WorldWideScience

Sample records for ash mud boulders

  1. Heterogeneous Catalysts for VOC Oxidation from Red Mud and Bagasse Ash Carbon

    Science.gov (United States)

    Pande, Gaurav

    A range of VOC oxidation catalysts have been prepared in this study from agricultural and industrial waste as the starting point. The aim is to prepare catalysts with non-noble metal oxides as the active catalytic component (iron in red mud). The same active component was also supported on activated carbon obtained from unburned carbon in bagasse ash. Red mud which is an aluminum industry waste and rich in different phases of iron as oxide and hydroxide is used as the source for the catalytically active species. It is our aim to enhance the catalytic performance of red mud which though high in iron concentration has a low surface area and may not have the properties of an ideal catalyst by itself. In one of the attempts to enhance the catalytic performance, we have tried to leach red mud for which we have explored a range of leaching acids for effecting the leaching most efficiently and then precipitated the iron from the leachate as its hydroxide by precipitating with alkali solution followed by drying and calcination to give high surface area metal oxide material. Extensive surface characterization and VOC oxidation catalytic testing were performed for these solids. In a step to further enhance the catalytic activity towards oxidation, copper was introduced by taking another industrial waste from the copper tubing industry viz. the pickling acid. Copper has a more favourable redox potential making it catalytically more effective than iron. To make the mixed metal oxide, red mud leachate was mixed with the pickling acid in a pre-decided ratio before precipitating with alkali solution followed by drying and calcination as was done with the red mud leachate. The results from these experiments are encouraging. The temperature programmed reduction (TPR) of the solids show that the precipitate of red mud leachates show hydrogen uptake peak at a lower temperature than for just the calcined red mud. This could be due to the greatly enhanced surface area of the prepared

  2. Mud Flow - Slow and Fast

    Science.gov (United States)

    Mei, C. C.; Liu, K.-F.; Yuhi, M.

    Heavy and persistent rainfalls in mountainous areas can loosen the hillslope and induce mud flows which can move stones, boulders and even trees, with destructive power on their path. In China where 70% of the land surface is covered by mountains, debris flows due to landslides or rainfalls affect over 18.6% of the nation. Over 10,000 debris flow ravines have been identified; hundreds of lives are lost every year [1]. While accurate assessment is still pending, mud flows caused by Hurr icane Mitch in 1998 have incurred devastating floods in Central America. In Honduras alone more than 6000 people perished. Half of the nation's infrastructures were damaged. Mud flows can also be the result of volcanic eruption. Near the volcano, lava and pyroclastic flows dominate. Further downstream solid particles become smaller and can mix with river or lake water, rainfall, melting snow or ice, or eroded soil, resulting in hyperconcentrated mud mixed with rocks. The muddy debris can travel at high speeds over tens of miles down the hill slopes and devastate entire communities. In 1985 the catastrophic eruption of Nevado del Ruiz in Colombia resulted in mud flows which took the life of 23,000 inhabitants in the town of Amero [2]. During the eruption of Mt. Pinatubo in Phillipnes in 1991, one cubic mile of volcanic ash and rock fragments fell on the mountain slopes. Seasonal rain in the following months washed down much of the loose deposits, causing damage to 100,000 villages. These catastrophes have been vividly recorded in the film documentary by Lyons [3].

  3. Use of fly ash, phosphogypsum and red mud as a liner material for the disposal of hazardous zinc leach residue waste.

    Science.gov (United States)

    Coruh, Semra; Ergun, Osman Nuri

    2010-01-15

    Increasing amounts of residues and waste materials coming from industrial activities in different processes have become an increasingly urgent problem for the future. The release of large quantities of heavy metals into the environment has resulted in a number of environmental problems. The present study investigated the safe disposal of the zinc leach residue waste using industrial residues such as fly ash, phosphogypsum and red mud. In the study, leachability of heavy metals from the zinc leach residue has been evaluated by mine water leaching procedure (MWLP) and toxicity characteristic leaching procedure (TCLP). Zinc removal from leachate was studied using fly ash, phosphogypsum and red mud. The adsorption capacities and adsorption efficiencies were determined. The adsorption rate data was analyzed according to the pseudo-second-order kinetic, Elovich kinetic and intra-particle diffusion kinetic models. The pseudo-second-order kinetic was the best fit kinetic model for the experimental data. The results show that addition of fly ash, phosphogypsum and red mud to the zinc leach residue drastically reduces the heavy metal content in the leachate and could be used as liner materials.

  4. Leachability of heavy metals in geopolymer-based materials synthesized from red mud and rice husk ash

    Science.gov (United States)

    Nguyen, Hoc Thang; Pham, Vo Thi Ha Quyen; Dang, Thanh Phong; Dao, Thanh Khe

    2018-04-01

    Red mud is an industrial waste generated during aluminum production from bauxite whereas rice husk ash is an agricultural waste from burning of rice husk that could cause negative impact on the environment if not properly managed. This study demonstrates the utilization of red mud in combination with rice husk ash to form a geopolymer-based material which can be used as bricks or replacement for traditional cement materials. The focus of this study is on the leachability of heavy metals in the raw materials and the geopolymer as this would be significant in assessing the environmental impact of the product. Leachability of metals such as Cu, Zn, Cd, Pb, Fe, and Cr was evaluated based on European (EN 124572-2 EU CEN TC292/ CEN TC 308) standard with pH value 7. Results indicate that the leachability of these metals in the geopolymer matrix is lower than that of the raw materials.

  5. Development of heat resistant geopolymer-based materials from red mud and rice husk ash

    Science.gov (United States)

    Thang, Nguyen Hoc; Nhung, Le Thuy; Quyen, Pham Vo Thi Ha; Phong, Dang Thanh; Khe, Dao Thanh; Van Phuc, Nguyen

    2018-04-01

    Geopolymer is an inorganic polymer composite developed by Joseph Davidovits in 1970s. Such material has potentials to replace Ordinary Portland Cement (OPC)-based materials in the future because of its lower energy consumption, minimal CO2 emissions and lower production cost as it utilizes industrial waste resources. Hence, geopolymerization and the process to produce geopolymers for various applications like building materials can be considered as green industry. Moreover, in this study, red mud and rice husk ash were used as raw materials for geopolymeric production, which are aluminum industrial and agricultural wastes that need to be managed to reduce their negative impact to the environment. The red mud and rice husk ash were mixed with sodium silicate (water glass) solution to form geopolymer paste. The geopolymer paste was filled into 5-cm cube molds according to ASTM C109/C109M 99, and then cured at room temperature for 28 days. These products were then tested for compressive strength and volumetric weight. Results indicated that the material can be considered lightweight with a compressive strength at 28 days that are in the range of 6.8 to 15.5 MPa. Moreover, the geopolymer specimens were also tested for heat resistance at a temperature of 1000oC for 2 hours. Results suggest high heat resistance with an increase of compressive strength from 262% to 417% after exposed at high temperature.

  6. Durability of Bricks Coated with Red mud Based Geopolymer Paste

    Science.gov (United States)

    Singh, Smita; Basavanagowda, S. N.; Aswath, M. U.; Ranganath, R. V.

    2016-09-01

    The present study is undertaken to assess the durability of concrete blocks coated with red mud - fly ash based geopolymer paste. Concrete blocks of size 200 x 200 x 100mm were coated with geopolymer paste synthesized by varying the percentages of red mud and fly ash. Uncoated concrete blocks were also tested for the durability for comparison. In thermal resistance test, the blocks were subjected to 600°C for an hour whereas in acid resistance test, they were kept in 5% sulphuric acid solution for 4 weeks. The specimens were thereafter studied for surface degradation, strength loss and weight loss. Pastes with red mud percentage greater than 50% developed lot of shrinkage cracks. The blocks coated with 30% and 50% red mud paste showed better durability than the other blocks. The use of blocks coated with red mud - fly ash geopolymer paste improves the aesthetics, eliminates the use of plaster and improves the durability of the structure.

  7. Mount St. Helens ash and mud: Chemical properties and effects on germination and establishment of trees and browse plants.

    Science.gov (United States)

    M.A. Radwan; Dan L. Campbell

    1981-01-01

    Chemical properties of ash and mud from the 1980 volcanic eruption of Mount St. Helens and their effect on germination and seedling production of selected plants were studied. The volcanic materials were low in some important nutrients and cation exchange capacity, and they adversely affected seedling production. Catsear, a preferred wildlife browse, and lodgepole pine...

  8. Lightweight Heat Resistant Geopolymer-based Materials Synthesized from Red Mud and Rice Husk Ash Using Sodium Silicate Solution as Alkaline Activator

    Directory of Open Access Journals (Sweden)

    Hoc Thang Nguyen

    2017-01-01

    Full Text Available Geopolymer is an inorganic polymer composite with potentials to replace Ordinary Portland Cement (OPC-based materials in the future because of its lower energy consumption, minimal CO2 emissions and lower production cost as it utilizes industrial waste resources. Hence, geopolymerization and the process to produce geopolymers for various applications like building materials can be considered as green industry. Moreover, in our study, the raw materials we used are red mud and rice husk ash, which are are industrial and agricultural wastes that need to be managed to reduce their impact to the environment. The red mud and rice husk ash combined with sodium silicate (water glass solution were mixed to form geopolymer materials. Moreover, the geopolymer specimens were also tested for heat resistance at a temperature of 1000°C for 2 hours. Results suggest high heat resistance with an increase of compressive strength after exposed at high temperature.

  9. Fly-Ash-Based Geopolymers: How the Addition of Recycled Glass or Red Mud Waste Influences the Structural and Mechanical Properties

    Czech Academy of Sciences Publication Activity Database

    Toniolo, N.; Taveri, Gianmarco; Hurle, K.; Roether, J. A.; Ercole, P.; Dlouhý, Ivo; Boccaccini, A. R.

    2017-01-01

    Roč. 8, č. 3 (2017), s. 411-420 ISSN 2190-9385 EU Projects: European Commission(XE) 642557 - CoACH Institutional support: RVO:68081723 Keywords : Geopolymers * Fly ash * Red mud * Waste glass Subject RIV: JH - Ceramic s, Fire-Resistant Materials and Glass OBOR OECD: Ceramic s Impact factor: 1.220, year: 2016 https://www. ceramic -science.com/articles/all-articles.html?article_id=100566

  10. Mineral phases of green liquor dregs, slaker grits, lime mud and wood ash of a Kraft pulp and paper mill

    Energy Technology Data Exchange (ETDEWEB)

    Martins, Fernanda Machado [Laboratorio de Quimica Mineral Aplicada, Departamento de Quimica-UFPR, Universidade Federal do Parana (UFPR), CP 19081, CEP 81531990, Curitiba-PR (Brazil); Munhoz Martins, Joaniel [Laboratorio de Analise de Minerais e Rochas (LAMIR-UFPR) (Brazil); Ferracin, Luiz Carlos [Laboratorio Quimico da Votorantin Cimentos (Brazil); Cunha, Carlos Jorge da [Laboratorio de Quimica Mineral Aplicada, Departamento de Quimica-UFPR, Universidade Federal do Parana (UFPR), CP 19081, CEP 81531990, Curitiba-PR (Brazil)]. E-mail: cjdcunha@quimica.ufpr.br

    2007-08-17

    Four residues generated in a Kraft, pulp and paper plant, were characterized by X-ray fluorescence spectroscopy (XFA), powder X-ray diffraction (XRD), thermogravimmetric analysis (TG) and Fourier transform infrared spectroscopy (FTIR). A quantitative phase composition model, that accounts for the observed data and for the physico-chemical conditions of formation, was postulated for each material. Emphasis was given on the identification of the mineral components of each material. The green liquor dregs and the lime mud contain Calcite and Gipsite. The slaker grits contains Calcite, Portlandite, Pirssonite, Larnite and Brucite. The Calcite phase, present in the dregs and in the lime mud, has small amounts of magnesium replacing calcium. The wood ash contains Quartz as the major crystalline mineral phase.

  11. Mineral phases of green liquor dregs, slaker grits, lime mud and wood ash of a Kraft pulp and paper mill

    International Nuclear Information System (INIS)

    Martins, Fernanda Machado; Munhoz Martins, Joaniel; Ferracin, Luiz Carlos; Cunha, Carlos Jorge da

    2007-01-01

    Four residues generated in a Kraft, pulp and paper plant, were characterized by X-ray fluorescence spectroscopy (XFA), powder X-ray diffraction (XRD), thermogravimmetric analysis (TG) and Fourier transform infrared spectroscopy (FTIR). A quantitative phase composition model, that accounts for the observed data and for the physico-chemical conditions of formation, was postulated for each material. Emphasis was given on the identification of the mineral components of each material. The green liquor dregs and the lime mud contain Calcite and Gipsite. The slaker grits contains Calcite, Portlandite, Pirssonite, Larnite and Brucite. The Calcite phase, present in the dregs and in the lime mud, has small amounts of magnesium replacing calcium. The wood ash contains Quartz as the major crystalline mineral phase

  12. Experimental Study of Goaf Filling Materials Based on Red Mud

    Science.gov (United States)

    Mu, Mangen; Gao, Xiaozhen; Guo, Taoming; Hu, Xinping

    2018-01-01

    Red mud as soild waste is difficult to treatment. Goaf filling materials can make a large use of red mud. By the experimental study,we find that the red mud, fly ash, ground slag and desulfida-tion gypsum can be used to make goaf filling materials based on the principle of alkali excitation and metalion stability.Through the control variable method, we find that the optimal proportion of goaf filling materials based on red mud is red mud 55%, fly ash 30%, cement 7.5%, fly ash 2.5%, desulfurization gypsum 5%, admixture 1%, and water solid ratio=1:1.2.The 28days final material strength was 2.0 MPa,which achives the technical specification requirements.Through the test of SEM, XRD and IR, it is indicated that the strength formation of goaf filling material based on red mud is from the unformed linking hydration products of amorphous alkali excitation system. With curing time from 3 to 7 days, the unformed linking hydration products grown a lot of vitreous hydration products. When hydration reaction basicly finished after 28 days, the hydration products have developed into a large volume of massive vitreous with an extremely dense structure. The Ca2SiO3 mineral phase is significantly reduced, which is participate in hydration reactions. The decrease of Ca2SiO3 indicates that the Si-O bond in the system have been ruptured and reorganized.

  13. Fabrication of CuO-doped catalytic material containing zeolite synthesized from red mud and rice husk ash for CO oxidation

    Science.gov (United States)

    Hieu Do Thi, Minh; Thinh Tran, Quoc; Nguyen, Tri; Van Nguyen Thi, Thuy; Huynh, Ky Phuong Ha

    2018-06-01

    In this study a series of the CuO-doped materials containing zeolite with varying CuO contents were synthesized from red mud (RM) and rice husk ash (RHA). The rice husk ash/red mud with the molar ratio of , and being 1.8, 2.5 and 60, respectively, were maintained during the synthetic process of materials. The characteristic structure samples were analyzed by x-ray diffraction (XRD), Fourier transformed infrared spectroscopy (FTIR), scanning electron microscopy (SEM), transmission electron microscope (TEM), Brunauer–Emmett–Teller (BET) surface area and H2 temperature program reduction (H2-TPR). The catalytic activity of samples was evaluated in CO oxidation reaction in a microflow reactor at temperature range 200 °C–350 °C. The obtained results showed that all synthetic samples there exist the A-type zeolites with the average crystal size of 15–20 nm, the specific surface area of , and pore volume of . The material synthesized from RM and RHA with the zeolite structure (ZRM, undoped CuO) could also oxidize CO completely at 350 °C, and its activity was increase significantly when doped with CuO. CuO-doped materials with the zeolite structure exhibited excellent catalytic activity in CO oxidation. The ZRM sample loading 5 wt% CuO with particle nanosize about 10–30 nm was the best one for CO oxidation with complete conversion temperature at 275 °C.

  14. Tracking Boulders

    Science.gov (United States)

    2006-01-01

    13 March 2006 This Mars Global Surveyor (MGS) Mars Orbiter Camera (MOC) image shows a portion of a trough in the Sirenum Fossae region. On the floor and walls of the trough, large -- truck- to house-sized -- boulders are observed at rest. However, there is evidence in this image for the potential for mobility. In the central portion of the south (bottom) wall, a faint line of depressions extends from near the middle of the wall, down to the rippled trough floor, ending very near one of the many boulders in the area. This line of depressions is a boulder track; it indicates the path followed by the boulder as it trundled downslope and eventually came to rest on the trough floor. Because it is on Mars, even when the boulder is sitting still, this once-rolling stone gathers no moss. Location near: 29.4oS, 146.6oW Image width: 3 km (1.9 mi) Illumination from: upper left Season: Southern Summer

  15. EXPLOITATION OF GRANITE BOULDER

    Directory of Open Access Journals (Sweden)

    Ivan Cotman

    1994-12-01

    Full Text Available The processes of forming, petrography, features, properties and exploitation of granite boulders are described. The directional drilling and black powder blasting is the succesful method in exploitation of granite boulders (boulder technology (the paper is published in Croatian.

  16. Mud Flow Characteristics Occurred in Izuoshima Island, 2013

    Science.gov (United States)

    Takebayashi, H.; Egashira, S.; Fujita, M.

    2015-12-01

    Landslides and mud flows were occurred in the west part of the Izuoshima Island, Japan on 16 October 2013. The Izuoshima Island is a volcanic island and the land surface is covered by the volcanic ash sediment in 1m depth. Hence, the mud flow with high sediment concentration was formed. The laminar layer is formed in the debris flow from the bed to the fluid surface. On the other hand, the laminar flow is restricted near the bed in the mud flow and the turbulence flow is formed on the laminar flow layer. As a result, the equilibrium slope of the mud flow becomes smaller comparing to the debris flow. In this study, the numerical analysis mud flow model considering the effect of turbulence flow on the equilibrium slope of the mud flow is developed. Subsequently, the model is applied to the mud flow occurred in the Izuoshima Island and discussed the applicability of the model and the flow characteristics of the mud flow. The differences of the horizontal flow areas between the simulated results and the field data are compared and it was found that the outline of the horizontal shape of the flow areas is reproduced well. Furthermore, the horizontal distribution of the erosion and deposition area is reproduced by the numerical analysis well except for the residential area (Kandachi area). Kandachi area is judged as the erosion area by the field observation, but the sediment was deposited in the numerical analysis. It is considered that the 1.5hour heavy rain over 100mm/h after the mud flow makes the discrepancy. The difference of the horizontal distribution of the maximum flow surface elevation between the simulated results and the field data are compared and it was found that the simulated flow depth is overestimated slightly, because of the wider erosion area due to the coarse resolution elevation data. The averaged velocity and the depth of the mud flow was enough large to collapse the houses.

  17. Proposed Construction of Boulder Seismic Station Monitoring Sites, Boulder, Wyoming. Environmental Assessment

    Science.gov (United States)

    2009-02-01

    boreholes at the Boulder Seismic Station for research, development, test, and evaluation (RDT&E) as part of the U.S. Nuclear Treaty monitoring...14 LIST OF FIGURES Figure 1. Location of the proposed Boulder Seismic Station, borehole locations and associated buffers...juncture of Spring Creek and Scab Creek Road (Figure 1). Currently, the Boulder Seismic Station has a 13-element array of seismometers on the property

  18. Nutritional Considerations for Bouldering.

    Science.gov (United States)

    Smith, Edward J; Storey, Ryan; Ranchordas, Mayur K

    2017-08-01

    Bouldering competitions are held up to International level and governed by the International Federation of Sport Climbing. Bouldering has been selected to feature at the 2020 Olympic Games in Tokyo, however, physiological qualities and nutritional requirements to optimize performance remain inadequately defined due to large gaps in the literature. The primary goals of training include optimizing the capacity of the anaerobic energy systems and developing sport-specific strength, with emphasis on the isometric function of the forearm flexors responsible for grip. Bouldering athletes typically possess a lean physique, similar to the characteristics of sport climbers with reported body fat values of 6-12%. Athletes strive for a low body weight to improve power to weight ratio and limit the load on the extremities. Specialized nutritional support is uncommon and poor nutritional practices such as chronic carbohydrate restriction are prevalent, compromising the health of the athletes. The high intensity nature of bouldering demands a focus on adequate carbohydrate availability. Protein intake and timing should be structured to maximize muscle protein synthesis and recovery, with the literature suggesting 0.25-0.3 g/kg in 3-4 hr intervals. Supplementing with creatine and b-alanine may provide some benefit by augmenting the capacity of the anaerobic systems. Boulderers are encouraged to seek advice from nutrition experts to enhance performance, particularly important when weight loss is the desired outcome. Further research is warranted across all nutritional aspects of bouldering which is summarized in this review.

  19. From oil-based mud to water-based mud

    International Nuclear Information System (INIS)

    Christiansen, C.

    1991-01-01

    Maersk Olie og Gas AS has used low toxic oil-based muds extensively since 1982 for drilling development wells and later in the development of horizontal well drilling techniques. However, in view of the strong drive towards a reduction in the amount of oil discharged to the North Sea from the oil industry, Maersk Olie og Gas AS initiated trials with new or improved types of water-based mud, first in deviated wells (1989) and then in horizontal wells (1990). The paper reviews Maersk Olie og Gas As experience with oil-based mud since the drilling of the first horizontal well in 1987, specifically with respect to cuttings washing equipment, oil retention on cuttings, and the procedure for monitoring of this parameter. It describes the circumstances leading to the decision to revert to water-based mud systems. Finally, it reviews the experience gained so far with the new improved types of water-based mud systems, mainly glycol and KCl/polymer mud systems. Comparison of operational data, such as rate of penetration, torque and drag, etc., is made between wells drilled with oil-based mud and water-based mud. The trials with the new improved types of water-based mud systems have been positive, i.e. horizontal wells can be drilled successfully with water-based mud. As a result, Maersk Olie og and Gas AS has decided to discontinue the use of low toxic oil-based muds in the Danish sector of the North Sea

  20. A study of burrow morphology in representative axiidean and gebiidean mud shrimps, from the Persian Gulf and Gulf of Oman, Iran

    Directory of Open Access Journals (Sweden)

    Vahid Sepahvand

    Full Text Available Mud shrimps (formerly Thalassinidea are common burrow dwelling decapod crustaceans in the littoral zone of the Persian Gulf and Gulf of Oman. Their burrow morphology was investigated using foam casting methods. The present study shows that the burrow morphology in Upogebia carinicauda is not consistent and the recorded variations are based on habitat type and some physical characteristics of sediments. Adult burrow morphology in sandy-muddy substrate with shells, and boulder field habitats were Y-shaped and complex burrows of horizontal channels with turning chambers and vertical connections to internal passages or crevices of boulders, respectively. In burrows of U. carinicauda, some narrow passages, connected to the upper part of adult burrows in sandy-muddy habitats, belong to juveniles. Another species, Neocallichirus jousseaumei was found under boulders in sandy-muddy habitats of the Gulf of Oman and Qeshm Island, Persian Gulf. Since this type of habitat is special in some features, no conspicuous ex-current openings (usually obvious as conical mounds of extruded sediment have been observed on the sediment surface; as these were hidden among the boulders surrounded by mixed sand and shells. The only method for observing this type of burrow was to remove the boulders by hand or lever.

  1. Boulder Dislodgment Reloaded: New insights from boulder transport and dislodgement by tsunamis and storms from three-dimensional numerical simulations with GPUSPH

    Science.gov (United States)

    Weiss, R.; Zainali, A.

    2014-12-01

    Boulders can be found on many coastlines around the globe. They are generally thought to be moved either during coastal storms or tsunamis because they are too heavy to be moved by more common marine or coastal processes. To understand storm and tsunami risk at given coastline, the event histories of both events need to be separated to produce a robust event statistics for quantitative risk analyses. Because boulders are most likely only moved by coastal storms or tsunamis, they are very suitable to produce the data basis for such event statistics. Boulder transport problem has been approached by comparing the driving with resisting forces acting on a boulder. However, we argue that this approach is not sufficient because the comparison of resisting and driving forces only constitutes boulder motion, but not for boulder dislodgment. Boulder motion means that the boulder starts to move out of its pocket. However, this motion does not guarantee that the boulder will reach the critical dislodgment position. Boulder dislodgment is a necessary condition to identify whether or not a boulder has moved. For boulder dislodgement, an equation of motion is needed, and that equation is Newtons Second Law of Motion (NSL). We perform fully coupled three-dimensional numerical simulation of boulders moved by waves where the boulders move according to NSL. Our numerical simulations are the first of their kind applied to tsunami and storm boulder motion. They show how storm and tsunami waves interact with boulders in a more realistic physical setting, and highlight the importance of submergence. Based on our simulations we perform a dimensional analysis that identifies the Froude number as important parameter, which can be considered large only in the front of tsunami waves, but small in the rest of tsunami wave and also generally small in storm waves. From a general point of view, our results indicate that the boulder transport problem is more complex than recently considered, and

  2. Utilization technology on slurried ash

    Energy Technology Data Exchange (ETDEWEB)

    Kanbe, Yoshio; Yasuda, Minoru; Furuki, Yasuhiko [The Coal Mining Research Centre, Japan, Tokyo, Japan; Electric Power Development Co., Ltd., Tokyo (Japan))

    1987-08-01

    Three research results of the utilization technology on slurried ash were reported. As for the utilization as the fly ash quick setting (FQS) backfill grout for tail void in shield works of tunneling, grout blending was simplified, the blended solution of cement, clay, additives and water was stabilized, and a favorable workability and long term durability were obtained. As for the utilization as the material of a SMW (soil mixing wall) method for continuous walls in long shaft digging, a fly ash-gypsum-cement (FGC) stabilizer showed an excellent workability and remarkably high water-tightness as compared with conventional cement bentonite. As for the utilization as the material of an injection method of overlay mats in foundation works of light weight structures on the sea bed mud foundation, since a FGC concrete weight in water was remarkably light as 0.7t/m{sup 3}, no both large mold form strength and vibration compacting were required. 10 figs., 8 tabs.

  3. Management of Lignite Fly Ash for Improving Soil Fertility and Crop Productivity

    Science.gov (United States)

    Ram, Lal C.; Srivastava, Nishant K.; Jha, Sangeet K.; Sinha, Awadhesh K.; Masto, Reginald E.; Selvi, Vetrivel A.

    2007-09-01

    Lignite fly ash (LFA), being alkaline and endowed with excellent pozzolanic properties, a silt loam texture, and plant nutrients, has the potential to improve soil quality and productivity. Long-term field trials with groundnut, maize, and sun hemp were carried out to study the effect of LFA on growth and yield. Before crop I was sown, LFA was applied at various doses with and without press mud (an organic waste from the sugar industry, used as an amendment and source of nutrients). LFA with and without press mud was also applied before crops III and V were cultivated. Chemical fertilizer, along with gypsum, humic acid, and biofertilizer, was applied in all treatments, including the control. With one-time and repeat applications of LFA (with and without press mud), yield increased significantly (7.0-89.0%) in relation to the control crop. The press mud enhanced the yield (3.0-15.0%) with different LFA applications. The highest yield LFA dose was 200 t/ha for one-time and repeat applications, the maximum yield being with crop III (combination treatment). One-time and repeat application of LFA (alone and in combination with press mud) improved soil quality and the nutrient content of the produce. The highest dose of LFA (200 t/ha) with and without press mud showed the best residual effects (eco-friendly increases in the yield of succeeding crops). Some increase in trace- and heavy-metal contents and in the level of γ-emitters in soil and crop produce, but well within permissible limits, was observed. Thus, LFA can be used on a large scale to boost soil fertility and productivity with no adverse effects on the soil or crops, which may solve the problem of bulk disposal of fly ash in an eco-friendly manner.

  4. Probability of Boulders

    DEFF Research Database (Denmark)

    Ditlevsen, Ove Dalager

    1997-01-01

    To collect background information for formulating a description of the expected soil properties along the tunnel line, in 1987 Storebælt initiated a statistical investigation of the occurrence and size of boulders in the Great Belt area. The data for the boulder size distribution were obtained....... The data collection part of the investigation was made on the basis of geological expert advice (Gunnar Larsen, Århus) by the Danish Geotechnical Institute (DGI).The statistical data analysis combined with stochastic modeling based on geometry and sound wave diffraction theory gave a point estimate...

  5. Engineered covers for mud pit closures Central Nevada Test Area, Nevada

    International Nuclear Information System (INIS)

    Madsen, D.D.

    2000-01-01

    Two abandoned drilling mud pits impacted with petroleum hydrocarbons were determined to require closure action at the Central Nevada Test Area. The UC-4 Mud Pit C is approximately 0.12 hectares (0.3 acres) and 1.2 meters (4 feet) in depth. The UC-1 Central Mud Pit (CMP) is approximately 1.54 hectares (3.8 acres) and 2.4 meters (8 feet) in depth. Both mud pits contain bentonite drilling muds with a thin dry crust, low shear strength, low permeability, and high moisture content. The following closure methodologies were evaluated: stabilization by mixing/injection with soil, fly ash, and lime; excavation and disposal; on-site drying; thermal destruction; wick drains; administrative closure (postings and land-use restrictions); and engineered covers. Based upon regulatory closure criteria, implementation, and cost considerations, the selected remedial alternative was the construction of an engineered cover. A multilayered cover with a geo-grid and geo-synthetic clay liner (GCL) was designed and constructed over the UC-4 Mud Pit C to evaluate the constructability and applicability of the design for the CMP cover. The geo-grid provided structural strength for equipment and material loads during cover construction, and the GCL was used as a moisture infiltration barrier. The design was determined to be constructable and applicable. To reduce project costs for the CMP cover, a vegetative cover was designed with drainage toward the center of the cover rather than the perimeter. The vegetative cover with the internal drainage design resulted in a fill volume reduction of approximately 63 percent compared to the multilayered cover design with a GCL

  6. Factors controlling mud accumulation in the Heuksan mud belt off southwestern Korea

    Science.gov (United States)

    Chang, Tae Soo; Ha, Hun Jun; Chun, Seung Soo

    2015-12-01

    The Heuksan mud belt (hereafter HMB) is 20~50 km wide, ~200 km long, and ~50 m thick, having accumulated in the course of the Holocene transgression on the tide-dominated epicontinental shelf southwest of Korea. The internal architecture of the HMB is characterized by offshore prograding clinoforms. Of particular interest are the depositional processes responsible for this anomalously thick mud accumulation within a relatively short period of time. Tidal currents are important in the dispersal of mud in the HMB, although these alone cannot explain such an enormous mud deposit. In order to understand the formative processes of the HMB, a detailed sedimentary facies analysis, including high-resolution grain-size measurements, has been conducted on more than 30 short cores and three long drill cores recovered from the mud belt. Five major mud facies were identified. Of these, mud sequences showing a thickening-thinning trend of alternating silt and clay laminae suggestive of a tidal origin occur dominantly at inner to mid shelf locations. By contrast, internally structureless muds with sharp bases and no bioturbation, which are interpreted of representing fluid-mud deposits, are widespread at mid to outer shelf locations. Wave-generated mud ripples and storm beds on the inner shelf suggest that storm waves in winter resuspend previously deposited mud to form near-bed fluid-mud suspensions with resulting gravity-driven mud transport across the low-gradient outer shelf. This previously not recognized process is probably a major factor controlling depositional processes on the giant mud belt, enabling rapid accumulation and offshore progradation even during transgression, i.e., at times of sea-level rise.

  7. 78 FR 48670 - Boulder Canyon Project

    Science.gov (United States)

    2013-08-09

    ... DEPARTMENT OF ENERGY Western Area Power Administration Boulder Canyon Project AGENCY: Western Area... Canyon Project (BCP) electric service provided by the Western Area Power Administration (Western). The... INFORMATION: Hoover Dam, authorized by the Boulder Canyon Project Act (45 Stat. 1057, December 21, 1928), sits...

  8. 77 FR 48151 - Boulder Canyon Project

    Science.gov (United States)

    2012-08-13

    ... DEPARTMENT OF ENERGY Western Area Power Administration Boulder Canyon Project AGENCY: Western Area... Canyon Project (BCP) electric service provided by the Western Area Power Administration (Western). The... INFORMATION: Hoover Dam, authorized by the Boulder Canyon Project Act (45 Stat. 1057, December 21, 1928), sits...

  9. 76 FR 56430 - Boulder Canyon Project

    Science.gov (United States)

    2011-09-13

    ... DEPARTMENT OF ENERGY Western Area Power Administration Boulder Canyon Project AGENCY: Western Area... Project (BCP) electric service provided by the Western Area Power Administration (Western). The Rates will... by the Boulder Canyon Project Act (45 Stat. 1057, December 21, 1928), sits on the Colorado River...

  10. 76 FR 8359 - Boulder Canyon Project

    Science.gov (United States)

    2011-02-14

    ... DEPARTMENT OF ENERGY Western Area Power Administration Boulder Canyon Project AGENCY: Western Area... Western Area Power Administration (Western) is proposing an adjustment to the Boulder Canyon Project (BCP... Reclamation Project Act of 1939 (43 U.S.C. 485h(c)), and other acts that specifically apply to the project...

  11. 78 FR 7775 - Boulder Canyon Project

    Science.gov (United States)

    2013-02-04

    ... DEPARTMENT OF ENERGY Western Area Power Administration Boulder Canyon Project AGENCY: Western Area...), is proposing an adjustment to the Boulder Canyon Project (BCP) electric service base charge and rates... subsequent laws, particularly section 9(c) of the Reclamation Project Act of 1939 (43 U.S.C. 485h(c)); and...

  12. 77 FR 2533 - Boulder Canyon Project

    Science.gov (United States)

    2012-01-18

    ... DEPARTMENT OF ENERGY Western Area Power Administration Boulder Canyon Project AGENCY: Western Area...), is proposing an adjustment to the Boulder Canyon Project (BCP) electric service base charge and rates...) of the Reclamation Project Act of 1939 (43 U.S.C. 485h(c)); and other acts that specifically apply to...

  13. Toward a new paradigm for boulder dislodgement during storms

    Science.gov (United States)

    Weiss, Robert; Sheremet, Alex

    2017-07-01

    Boulders are an important coastal hazard event deposit because they can only be moved by tsunamis and energetic storms effects of storms. Storms and tsunami are competing processes for coastal change along many shorelines. Therefore, distinguishing the boulders that were moved during a storm from those moved by a tsunami is important. In this contribution, we present the results of a parameter study based on the TRIADS model for wave shoaling on mildly sloping beaches, coupled with a boulder-dislodgement model that is based on Newton's Second Law of Motion. The results show how smaller slopes expose the waves longer to the nonlinear processes, thus increasing the energy in the infragravity wave band. More energy in the infragravity wave band means that there are more energy wave lengths that can dislodge larger boulders. At the same time, a steeper slope lowers the threshold for boulder dislodgement (critical angle of dislodgement), making it more likely for larger boulders to be dislodged on a steeper slope. The competition between these two processes govern boulder dislodgement during storms and is investigated inhere.

  14. Engineering properties of lightweight geopolymer synthesized from coal bottom ash and rice husk ash

    Science.gov (United States)

    Thang, Nguyen Hoc; Hoa, Nguyen Ngoc; Quyen, Pham Vo Thi Ha; Tuyen, Nguyen Ngoc Kim; Anh, Tran Vu Thao; Kien, Pham Trung

    2018-04-01

    Geopolymer technology was developed by Joseph Davidovits in 1970s based on reactions among alumino-silicate resources in high alkaline conditions. Geopolymer has been recently gaining attention as an alternative binder for Ordinary Portland cement (OPC) due to its low energy and CO2 burden. The raw materials used for geopolymerization normally contain high SiO2 and Al2O3 in the chemical compositions such as meta-kaoline, rice husk ash, fly ash, bottom ash, blast furnace slag, red mud, and others. Moreover, in this paper, coal bottom ash (CBA) and rice husk ash (RHA), which are industrial and agricultural wastes, respectively, were used as raw materials with high alumino-silicate resources. Both CBA and RHA were mixed with sodium hydroxide (NaOH) solution for 20 minutes to obtain the geopolymer pastes. The pastes were filled in 5-cm cube molds according to ASTM C109/C109M 99, and then cured at room condition for hardening of the geopolymer specimens. After 24 hours, the specimens were removed out of the molds and continuously cured at room condition for 27 days. The geopolymer-based materials were then tested for engineering properties such as compressive strength (MPa), volumetric weight (kg/m3), and water absorption (kg/m3). Results indicated that the material can be considered lightweight with volumetric weight from 1192 to 1425 kg/m3; compressive strength at 28 days is in the range of 12.38 to 37.41 MPa; and water absorption is under 189.92 kg/m3.

  15. Drilling mud

    Energy Technology Data Exchange (ETDEWEB)

    Rusayev, A A; Bibikov, K V; Simonenkov, I D; Surkova, K I

    1982-01-01

    Drilling mud is proposed which contains clay, water, water output reducer, pH regulator, viscosity reducer and hydrogen sulfide absorber. In order to improve the absorbing capacity of the drilling mud with pH 8-11 and simultaneously preservation of the technological properties of the mud, it contains as the absorber of hydrogen sulfide pyrite cinders with the following ratio of components, % by mass: clay 5.0-35.0; water output reducer 0.2-2.0; pH regulator 0.05-0.25; viscosity reducer 0.1-1.0; pyrite cinders 0.5-4.0; water--the rest.

  16. Drilling mud

    Energy Technology Data Exchange (ETDEWEB)

    Baranovskiy, V D; Brintsev, A I; Gusev, V G; Katenev, Ye P; Pokhorenko, I V

    1979-10-25

    A drilling mud is proposed, which contains a dispersion medium, a dispersion phase, for instance, clay, a stabilizer reagent, for instance, carboxymethylcellulose and a weighter. In order to reduce the viscosity and to increase the stability of the mud it contains as the dispersion medium a 75% aqueous solution of the L-7 reagent. To increase the salt resistance of the mud, it additionally contains sodium chloride in a volume of 4.04.5 percent by weight, and to regulate the alkalinity, it additionally contains sodium hydroxide in a volume of 1.1 to 1.3 percent by weight.

  17. Numerical simulation of mud erosion rate in sand-mud alternate layer and comparison with experiment

    Science.gov (United States)

    Yoshida, T.; Yamaguchi, T.; Oyama, H.; Sato, T.

    2015-12-01

    For gas production from methane hydrates in sand-mud alternate layers, depressurization method is expected as feasible. After methane hydrate is dissociated, gas and water flow in pore space. There is a concern about the erosion of mud surface and it may result in flow blockage that disturbs the gas production. As a part of a Japanese National hydrate research program (MH21, funded by METI), we developed a numerical simulation of water-induced mud erosion in pore-scale sand-mud domains to model such mud erosion. The size of which is of the order of 100 micro meter. Water flow is simulated using a lattice Boltzmann method (LBM) and mud surface is treated as solid boundary with arbitrary shape, which changes with time. Periodic boundary condition is adopted at the domain boundaries, except for the surface of mud layers and the upper side. Shear stress acting on the mud surface is calculated using a momentum-exchange method. Mud layer is eroded when the shear stress exceeds a threshold coined a critical shear stress. In this study, we compared the simulated mud erosion rate with experimental data acquired from an experiment using artificial sand-mud core. As a result, the simulated erosion rate agrees well with that of the experiment.

  18. Wake patterns behind boulders in the rings of Saturn

    International Nuclear Information System (INIS)

    Brattli, A.; Havnes, O.; Melandsoe, F.

    2002-01-01

    The flow of charged dust around an electrically charged boulder moving through an environment thought to be typical of planatery rings is studied. As the boulder moves through the ring dust it will excite a V-shaped Mach cone pattern of a form and complexity which varies significantly with boulder size, relative velocity between the boulder and the dust, and with dust plasma conditions. Parameters relevant to the Saturnian ring system are used to compute examples which demonstrate the change in Mach cone patterns with the relevant parameters. Shortcomings of the model are discussed and ways to improve the calculations of Mach cone patterns are pointed out

  19. Evaluation of blends bauxite-calcination-method red mud with other industrial wastes as a cementitious material: Properties and hydration characteristics

    International Nuclear Information System (INIS)

    Zhang Na; Liu Xiaoming; Sun Henghu; Li Longtu

    2011-01-01

    Red mud is generated from alumina production, and its disposal is currently a worldwide problem. In China, large quantities of red mud derived from bauxite calcination method are being discharged annually, and its utilization has been an urgent topic. This experimental research was to evaluate the feasibility of blends red mud derived from bauxite calcination method with other industrial wastes for use as a cementitious material. The developed cementitious material containing 30% of the bauxite-calcination-method red mud possessed compressive strength properties at a level similar to normal Portland cement, in the range of 45.3-49.5 MPa. Best compressive strength values were demonstrated by the specimen RSFC2 containing 30% bauxite-calcination-method red mud, 21% blast-furnace slag, 10% fly ash, 30% clinker, 8% gypsum and 1% compound agent. The mechanical and physical properties confirm the usefulness of RSFC2. The hydration characteristics of RSFC2 were characterized by XRD, FTIR, 27 Al MAS-NMR and SEM. As predominant hydration products, ettringite and amorphous C-S-H gel are principally responsible for the strength development of RSFC2. Comparing with the traditional production for ordinary Portland cement, this green technology is easier to be implemented and energy saving. This paper provides a key solution to effectively utilize bauxite-calcination-method red mud.

  20. Multi-Sensor Mud Detection

    Science.gov (United States)

    Rankin, Arturo L.; Matthies, Larry H.

    2010-01-01

    Robust mud detection is a critical perception requirement for Unmanned Ground Vehicle (UGV) autonomous offroad navigation. A military UGV stuck in a mud body during a mission may have to be sacrificed or rescued, both of which are unattractive options. There are several characteristics of mud that may be detectable with appropriate UGV-mounted sensors. For example, mud only occurs on the ground surface, is cooler than surrounding dry soil during the daytime under nominal weather conditions, is generally darker than surrounding dry soil in visible imagery, and is highly polarized. However, none of these cues are definitive on their own. Dry soil also occurs on the ground surface, shadows, snow, ice, and water can also be cooler than surrounding dry soil, shadows are also darker than surrounding dry soil in visible imagery, and cars, water, and some vegetation are also highly polarized. Shadows, snow, ice, water, cars, and vegetation can all be disambiguated from mud by using a suite of sensors that span multiple bands in the electromagnetic spectrum. Because there are military operations when it is imperative for UGV's to operate without emitting strong, detectable electromagnetic signals, passive sensors are desirable. JPL has developed a daytime mud detection capability using multiple passive imaging sensors. Cues for mud from multiple passive imaging sensors are fused into a single mud detection image using a rule base, and the resultant mud detection is localized in a terrain map using range data generated from a stereo pair of color cameras.

  1. Volcanic ash deposition, eelgrass beds, and inshore habitat loss from the 1920s to the 1990s at Chignik, Alaska

    Science.gov (United States)

    Zimmermann, Mark; Ruggerone, Gregory T.; Freymueller, Jeffrey T.; Kinsman, Nicole; Ward, David H.; Hogrefe, Kyle R.

    2018-03-01

    We quantified the shallowing of the seafloor in five of six bays examined in the Chignik region of the Alaska Peninsula, confirming National Ocean Service observations that 1990s hydrographic surveys were shallower than previous surveys from the 1920s. Castle Bay, Chignik Lagoon, Hook Bay, Kujulik Bay and Mud Bay lost volume as calculated from Mean Lower Low Water (Chart Datum) to the deepest depths and four of these sites lost volume from Mean High Water to the deepest depths. Calculations relative to each datum were made because tidal datum records exhibited an increase in tidal range in this region from the 1920s to the 1990s. Our analysis showed that Mud Bay is quickly disappearing while Chignik Lagoon is being reduced to narrow channels. Anchorage Bay was the only site that increased in depth over time, perhaps due to erosion. Volcanoes dominate the landscape of the Chignik area. They have blanketed the region in deep ash deposits before the time frame of this study, and some have had smaller ash-producing eruptions during the time frame of this study. Remobilization of land-deposited ash and redeposition in marine areas - in some locations facilitated by extensive eelgrass (Zostera marina) beds (covering 54% of Chignik Lagoon and 68% of Mud Bay in 2010) - is the most likely cause of shallowing in the marine environment. Loss of shallow water marine habitat may alter future abundance and distribution of several fish, invertebrate and avian species.

  2. A brief review on fly ash and its use in surface engineering

    Science.gov (United States)

    Bhajantri, Vishwanath; Krishna, Prasad; Jambagi, Sudhakar

    2018-04-01

    Fly ash is a by-product obtained from coal power plants. Over the past two decades, handling this industrial waste has been a great challenge for many developing countries. However, this menace can be used in many industrial applications viz., civil, automobile and aerospace applications. In civil industry, the fly ash has been used in concreate to enhance the porosity that increases the curing time of the concrete. The fly ash has been gaining importance these days as a feedstock material for many thermal spray processes. In automobile sector, the fly ash has been used as a thermal barrier coating in IC engines, whereas in aerospace industry, which demands lighter and stronger materials, the fly ash has been used as a reinforcement material. Hence, so far, fly ash has been used as an either single or a composite feed stock material in thermal spray processes. The fly ash with other materials like alumina, titania and red mud have been deposited using thermal spray processes. These coatings have exhibited higher wear, corrosion and erosion resistance as compared to the uncoated specimens. In this paper, a brief review on fly ash and its use, especially its use as a feed stock in thermal spray coating, is presented. Therefore, the use of fly ash has opened a new frontier of research in thermal spray coating area where economically viable coatings can be produced using industrial waste like fly ash.

  3. Physical and Chemical Properties of Sintering Red Mud and Bayer Red Mud and the Implications for Beneficial Utilization

    Science.gov (United States)

    Wang, Ping; Liu, Dong-Yan

    2012-01-01

    Performances of two common types of red mud, Bayer red mud and Sintering red mud, were investigated in this research. Their compositions, mechanical properties and microstructure characterization were measured through XRD, TG and SEM analysis. Their shear strength, particle size, density and hydraulic characteristics also had been performed. Huge differences between the basic mineral types of these two kinds of red mud also can be found. The comparison of compositions shows that CaCO3 content in Sintering red mud is higher, Bayer red mud has more hazardous elements such as As, Pb and Hg and both have a high concentration of radioactivity. The micro particle of Bayer red mud is finer and more disperse, but the Sintering red mud has higher shear strength. Combining the TG and hydraulic characteristics analysis, it can be shown that Bayer red mud has higher value of water content and Sintering red mud has higher hydraulic conductivity. The paper then illustrates that Sintering red mud can become the main filling material of supporting structure of red mud stocking yard. Bayer red mud has a high reuse value and also can be used as a mixing material of masonry mortar.

  4. Boulder Dislodgement by Tsunamis and Storms: Version 2.0

    Science.gov (United States)

    Weiss, Robert

    2016-04-01

    In the past, boulder dislodgement by tsunami and storm waves has been approached with a simple threshold approach in which a boulder was moved if the sum of the acting forces on the boulder is larger than zero. The impulse theory taught us, however, that this criterion is not enough to explain particle dislodgement. We employ an adapted version of the Newton's Second Law of Motion (NSLM) in order to consider the essence of the impulse theory which is that the sum of the forces has to exceed a certain threshold for a certain period of time. Furthermore, a classical assumption is to consider linear waves. However, when waves travel toward the shore, they alter due to non-linear processes. We employ the TRIADS model to quantify that change and how it impacts boulder dislodgement. We present our results of the coupled model (adapted NSLM and TRIADS model). The results project a more complex picture of boulder transport by storms and tsunami. The following question arises: What information do we actually invert, and what does it tell us about the causative event?

  5. Shallow-Water Mud Acoustics

    Science.gov (United States)

    2015-09-30

    1 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Shallow-Water Mud Acoustics William L. Siegmann...models and methods that explain observed material and acoustic properties of different physical types of shallow-ocean mud sediments. Other goals...are to assess prior data relating to the acoustic properties of mud and to provide guidance in the development and interpretation of experiments. A

  6. Geological Investigations on Boulder-Clay of E. Groningen

    NARCIS (Netherlands)

    Gijzel, van P.; Overweel, C.J.; Veenstra, H.J.

    1959-01-01

    In this article the results of a study on boulder-clay in the neighbourhood of Winschoten (N.E. Netherlands) are communicated (Chapter I). The underlying sediments of the boulder-clay in this area consist of fine preglacial sands and black clay. In the nuclei of the many drumlins a strongly

  7. Measurement of alpha radioactive air pollutants in fly ash brick dwellings

    International Nuclear Information System (INIS)

    Chauhan, R.P.; Kant, K.; Sharma, S.K.; Chakarvarti, S.K.

    2003-01-01

    The exposure of population to high concentrations of radon and its daughters for a long period lead to pathological effects like the respiratory functional changes and the occurrence of lung cancer. In the present study indoor radon monitoring has been carried out in fly ash brick dwellings in some villages/towns of district Faridabad, Haryana (India) using alpha sensitive LR-115 type II solid-state nuclear track detectors. The radon concentration levels in fly ash brick dwellings varied from 197 to 448 Bq m -3 with an average of 277±13 Bq m -3 while annual effective dose received by the occupants varied from 3.4 to 7.7 mSv with an average of 4.8±0.2 mSv. These results have been compared with the radon levels found in cemented and mud dwellings taken from our studies for these dwellings. These studies were also made simultaneously along with fly ash dwellings using same technique and in the same regions

  8. Revegetating fly ash landfills with Prosopis juliflora L.: impact of different amendments and Rhizobium inoculation.

    Science.gov (United States)

    Rai, U N; Pandey, K; Sinha, S; Singh, A; Saxena, R; Gupta, D K

    2004-05-01

    A revegetation trial was conducted to evaluate the feasibility of growing a legume species, Prosopis juliflora L., on fly ash ameliorated with combination of various organic amendments, blue-green algal biofertilizer and Rhizobium inoculation. Significant enhancements in plant biomass, photosynthetic pigments, protein content and in vivo nitrate reductase activity were found in the plants grown on ameliorated fly ash in comparison to the plants growing in unamended fly ash or garden soil. Higher growth was obtained in fly ash amended with blue-green algae (BGA) than farmyard manure or press mud (PM), a waste from sugar-processing industry, due to the greater contribution of plant nutrients, supply of fixed nitrogen and increased availability of phosphorus. Nodulation was suppressed in different amendments of fly ash with soil in a concentration-duration-dependent manner, but not with other amendments. Plants accumulated higher amounts of Fe, Mn, Cu, Zn and Cr in various fly ash amendments than in garden soil. Further, inoculation of the plant with a fly ash tolerant Rhizobium strain conferred tolerance for the plant to grow under fly ash stress conditions with more translocation of metals to the above ground parts. The results showed the potential of P. juliflora to grow in plantations on fly ash landfills and to reduce the metal contents of fly ash by bioaccumulation in its tissues.

  9. Tsunami-induced boulder transport - combining physical experiments and numerical modelling

    Science.gov (United States)

    Oetjen, Jan; Engel, Max; May, Simon Matthias; Schüttrumpf, Holger; Brueckner, Helmut; Prasad Pudasaini, Shiva

    2016-04-01

    Coasts are crucial areas for living, economy, recreation, transportation, and various sectors of industry. Many of them are exposed to high-energy wave events. With regard to the ongoing population growth in low-elevation coastal areas, the urgent need for developing suitable management measures, especially for hazards like tsunamis, becomes obvious. These measures require supporting tools which allow an exact estimation of impact parameters like inundation height, inundation area, and wave energy. Focussing on tsunamis, geological archives can provide essential information on frequency and magnitude on a longer time scale in order to support coastal hazard management. While fine-grained deposits may quickly be altered after deposition, multi-ton coarse clasts (boulders) may represent an information source on past tsunami events with a much higher preservation potential. Applying numerical hydrodynamic coupled boulder transport models (BTM) is a commonly used approach to analyse characteristics (e.g. wave height, flow velocity) of the corresponding tsunami. Correct computations of tsunamis and the induced boulder transport can provide essential event-specific information, including wave heights, runup and direction. Although several valuable numerical models for tsunami-induced boulder transport exist (e. g. Goto et al., 2007; Imamura et al., 2008), some important basic aspects of both tsunami hydrodynamics and corresponding boulder transport have not yet been entirely understood. Therefore, our project aims at these questions in four crucial aspects of boulder transport by a tsunami: (i) influence of sediment load, (ii) influence of complex boulder shapes other than idealized rectangular shapes, (iii) momentum transfers between multiple boulders, and (iv) influence of non-uniform bathymetries and topographies both on tsunami and boulder. The investigation of these aspects in physical experiments and the correct implementation of an advanced model is an urgent need

  10. 40 CFR 230.42 - Mud flats.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 24 2010-07-01 2010-07-01 false Mud flats. 230.42 Section 230.42... Aquatic Sites § 230.42 Mud flats. (a) Mud flats are broad flat areas along the sea coast and in coastal rivers to the head of tidal influence and in inland lakes, ponds, and riverine systems. When mud flats...

  11. Thermal Mud Molecular Overview

    Directory of Open Access Journals (Sweden)

    Ersin Odabasi

    2014-06-01

    Full Text Available Thermal mud (peloids, which are frequently used for thermal therapy purposes consist of organic and inorganic (minerals compounds in general. Organic structure is formed after a variety of chemical processes occurring in decades and comprise of a very complex structure. Stagnant water environment, herbal diversity, microorganism multiplicity and time are crucial players to form the structure. Data regarding description of organic compounds are very limited. Nowadays, it was clearly understood that a variety of compounds those are neglected in daily practice are found in thermal mud after GC-MS and similar methods are being frequently used. Those compounds which are biologically active are humic compounds, carboxylic acids, terpenoids, steroids and fatty acids. By comprising the thermal mud, these different compound groups which are related to divers areas from cosmetology to inflammation, make the thermal mud very meaningful in the treatment of human disease. In this review, it was tried to put forward the effects of several molecule groups those consisting of the thermal mud structure. [TAF Prev Med Bull 2014; 13(3.000: 257-264

  12. DOE Zero Energy Ready Home Case Study: Boulder ZED Design Build - Boulder, Colorado

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2014-11-01

    This case study describes a DOE Zero Energy Ready Home in Boulder, Colorado, that scored HERS 38 without PV and 0 with PV. This 2,504 ft2 custom home has advanced framed walls, superior insulation a ground-source heat pump, ERV, and triple-pane windows.

  13. Multiple severe typhoons in recent history revealed by coral boulders of northwestern Luzon, Philippines

    Science.gov (United States)

    Gong, Shou-Yeh; Wu, Tso-Ren; Liu, Sze-Chieh; Shen, Chuan-Chou; Siringan, Fernando; Lin, Han-Wei

    2017-04-01

    Meter-sized coral boulders occurred on Holocene reef flat at Pasuquin, Ilocos Norte and Cabugao, Ilocos Sur, Philippines. Boulders larger than 3 meters were located and measured by field survey and UAV photogrammetry. Boulders now distributed 45-140 m away from edge of Holocene reef flat, and above highest high tide. The lithology of those boulders is the same as the underlying Holocene coral reef at the sites, hence believed to be broken from reef edge locally. Fossil corals in those boulders mostly appeal not in upward-growing attitude but overturned or tilted. Several tens of photos were taken around selected boulders from different angles, and 3D models were established from the photos. Dimension and volumes were calculated from 3D models. Boulder volumes can be estimated much more accurately this way than simply multiple X, Y, and Z as many previous studies did. The volumes of boulders larger than 3 m in length vary from 10-52.6 m3. Assuming 2.1 g/cm3 for wet density, weights of boulders are estimated to range from 21-110 metric tons. Boulders of such size and weight obviously can't be moved by normal waves, and likely dislodged by Extreme Wave Event (EWE). Small and well-preserved corals were found in depressions on boulder surface and interpreted to represent timing of final displacement. Corals found on seven boulders at Pasuquin were 230Th dated to be 1782, 1904, 1946, 1957, 1978 and 2003 AD respectively. No tsunami was reported in historical records in northern Luzon for those years, but several documented typhoons could be responsible for displacement of each of those boulders. Another Porites boulder at Cabugao was dated to be tilted five times from 673-838 AD, averaging one EWE every 33 years. Such frequent occurrence of EWE is unlikely resulted from tsunami. Therefore, those coral boulders at Pasuquin and Cabugao are interpreted to be displaced by severe typhoons.

  14. Multiphase modelling of mud volcanoes

    Science.gov (United States)

    Colucci, Simone; de'Michieli Vitturi, Mattia; Clarke, Amanda B.

    2015-04-01

    Mud volcanism is a worldwide phenomenon, classically considered as the surface expression of piercement structures rooted in deep-seated over-pressured sediments in compressional tectonic settings. The release of fluids at mud volcanoes during repeated explosive episodes has been documented at numerous sites and the outflows resemble the eruption of basaltic magma. As magma, the material erupted from a mud volcano becomes more fluid and degasses while rising and decompressing. The release of those gases from mud volcanism is estimated to be a significant contributor both to fluid flux from the lithosphere to the hydrosphere, and to the atmospheric budget of some greenhouse gases, particularly methane. For these reasons, we simulated the fluid dynamics of mud volcanoes using a newly-developed compressible multiphase and multidimensional transient solver in the OpenFOAM framework, taking into account the multicomponent nature (CH4, CO2, H2O) of the fluid mixture, the gas exsolution during the ascent and the associated changes in the constitutive properties of the phases. The numerical model has been tested with conditions representative of the LUSI, a mud volcano that has been erupting since May 2006 in the densely populated Sidoarjo regency (East Java, Indonesia), forcing the evacuation of 40,000 people and destroying industry, farmland, and over 10,000 homes. The activity of LUSI mud volcano has been well documented (Vanderkluysen et al., 2014) and here we present a comparison of observed gas fluxes and mud extrusion rates with the outcomes of numerical simulations. Vanderkluysen, L.; Burton, M. R.; Clarke, A. B.; Hartnett, H. E. & Smekens, J.-F. Composition and flux of explosive gas release at LUSI mud volcano (East Java, Indonesia) Geochem. Geophys. Geosyst., Wiley-Blackwell, 2014, 15, 2932-2946

  15. NASA's Asteroid Redirect Mission: The Boulder Capture Option

    Science.gov (United States)

    Abell, Paul A.; Nuth, J.; Mazanek, D.; Merrill, R.; Reeves, D.; Naasz, B.

    2014-01-01

    NASA is examining two options for the Asteroid Redirect Mission (ARM), which will return asteroid material to a Lunar Distant Retrograde Orbit (LDRO) using a robotic solar-electric-propulsion spacecraft, called the Asteroid Redirect Vehicle (ARV). Once the ARV places the asteroid material into the LDRO, a piloted mission will rendezvous and dock with the ARV. After docking, astronauts will conduct two extravehicular activities (EVAs) to inspect and sample the asteroid material before returning to Earth. One option involves capturing an entire small (approximately 4-10 m diameter) near-Earth asteroid (NEA) inside a large inflatable bag. However, NASA is examining another option that entails retrieving a boulder (approximately 1-5 m) via robotic manipulators from the surface of a larger (approximately 100+ m) pre-characterized NEA. This option can leverage robotic mission data to help ensure success by targeting previously (or soon to be) well-characterized NEAs. For example, the data from the Hayabusa mission has been utilized to develop detailed mission designs that assess options and risks associated with proximity and surface operations. Hayabusa's target NEA, Itokawa, has been identified as a valid target and is known to possess hundreds of appropriately sized boulders on its surface. Further robotic characterization of additional NEAs (e.g., Bennu and 1999 JU3) by NASA's OSIRIS REx and JAXA's Hayabusa 2 missions is planned to begin in 2018. The boulder option is an extremely large sample-return mission with the prospect of bringing back many tons of well-characterized asteroid material to the Earth-Moon system. The candidate boulder from the target NEA can be selected based on inputs from the world-wide science community, ensuring that the most scientifically interesting boulder be returned for subsequent sampling. This boulder option for NASA's ARM can leverage knowledge of previously characterized NEAs from prior robotic missions, which provides more

  16. Fly ash for soil amelioration: A review on the influence of ash blending with inorganic and organic amendments

    Science.gov (United States)

    Ram, L. C.; Masto, R. E.

    2014-01-01

    Globally, fly ash (FA), generated in huge quantities from coal fired power plants is a problematic solid waste. Utilization of FA as an ameliorant for improving soil quality has received a great deal of attention over the past four decades, and many studies have been carried out worldwide. The silt-sized particles, low bulk density (BD), higher water holding capacity (WHC), favorable pH, and significant presence of plant nutrients in FA, make it a potential amendment for soils. The studies suggest enormous potential for the use of FA to improve cultivable, degraded/waste land, mine soil, landfills, and also to reclaim abandoned ash ponds, for agriculture and forestry. FA application improves the physical, chemical and biological qualities of soils to which it is applied. However, in some cases, depending on the characteristics of FA, the release of trace elements and soluble salts from FA to a soil-plant-human system could be a constraint. The effect is minimal in the case of weathered FA. The findings reflected the heterogeneity of ash characteristics, soil types, and agro-climatic conditions, thus a generalized conclusion on the impact of FA on plant species and soil quality is difficult. It is very important that the application of FA to soil must be very specific depending on the properties of the FA and soil. A considerable amount of research has been carried out to blend FA with varieties of organic and inorganic materials, like lime, gypsum, red mud, animal manure, poultry manure, sewage sludge, composts, press mud, vermicompost, biochar, bioinoculants, etc. Co-application of FA with these materials has much advantage: enhanced nutrient availability, decreased bioavailability of toxic metals, pH buffering, organic matter addition, microbial stimulation, overall improvement in the general health of the soil, etc. The performance of FA blending with organic and inorganic materials is better than FA alone treatments. Farm manure was found to be the most

  17. Chemical Speciation of Chromium in Drilling Muds

    International Nuclear Information System (INIS)

    Taguchi, Takeyoshi; Yoshii, Mitsuru; Shinoda, Kohzo

    2007-01-01

    Drilling muds are made of bentonite and other clays, and/or polymers, mixed with water to the desired viscosity. Without the drilling muds, corporations could not drill for oil and gas and we would have hardly any of the fuels and lubricants considered essential for modern industrial civilization. There are hundreds of drilling muds used and some kinds of drilling muds contain chromium. The chemical states of chromium in muds have been studied carefully due to concerns about the environmental influence. However it is difficult to determine the chemical state of chromium in drilling muds directly by conventional analytical methods. We have studied the chemical form of chromium in drilling muds by using a laboratory XAFS system and a synchrotron facility

  18. Rich mineralized boulders of the Rirang River, west Kalimantan

    International Nuclear Information System (INIS)

    Tjokrokardono, S.; Sastratenaya, A.S.

    1988-01-01

    The Rirang River is a small tributary of the Kalan River. It is 1.5 km long and flows in a N60 deg. E direction. To the west it is separated from the Sampurno Valley by an asymmetric pass with a relatively gentle slope on the Rirang side and a very steep slope down to the Sampurno River. The Rirang Valley lacks outcrops because of a high degree of alteration. It is known to contain mineralized boulders, most of which are of centimetric to decimetric size, but some may exceed 1 m. The uranium content in these boulders varies between 0.6 and 6.67%. Two types of mineralized boulders exist: banded and non-banded types. The former usually have a rounded shape due to erosion on their angles. They are composed of dark centimetric fragments of breccia, roughly aligned, giving a banded aspect, and are cemented by lighter coloured materials of monazite. The mineral composition of the fragments is of fine brown monazite, molybdenite, pyrite, rutile and tourmaline. Uranium minerals are located at the edges of the dark components. Most of the non-banded type boulders are of metasiltstone containing mineralized stringers of uraninite, molybdenite, pyrite, and a little monazite and tourmaline. Some investigations have been carried out, but the geological context and the origin of the boulders are, as yet, not fully understood. (author). 2 refs, 10 figs, 2 tabs

  19. 46 CFR 128.450 - Liquid-mud systems.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 4 2010-10-01 2010-10-01 false Liquid-mud systems. 128.450 Section 128.450 Shipping...: EQUIPMENT AND SYSTEMS Design Requirements for Specific Systems § 128.450 Liquid-mud systems. (a) Liquid-mud... this chapter. (b) Tanks for oil-based liquid mud must be fitted with tank vents equipped with flame...

  20. 30 CFR 250.1614 - Mud program.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 2 2010-07-01 2010-07-01 false Mud program. 250.1614 Section 250.1614 Mineral... OPERATIONS IN THE OUTER CONTINENTAL SHELF Sulphur Operations § 250.1614 Mud program. (a) The quantities, characteristics, use, and testing of drilling mud and the related drilling procedures shall be designed and...

  1. An advanced three-phase physical, experimental and numerical method for tsunami induced boulder transport

    Science.gov (United States)

    Oetjen, Jan; Engel, Max; Prasad Pudasaini, Shiva; Schüttrumpf, Holger; Brückner, Helmut

    2017-04-01

    Coasts around the world are affected by high-energy wave events like storm surges or tsunamis depending on their regional climatological and geological settings. By focusing on tsunami impacts, we combine the abilities and experiences of different scientific fields aiming at improved insights of near- and onshore tsunami hydrodynamics. We investigate the transport of coarse clasts - so called boulders - due to tsunami impacts by a multi-methodology approach of numerical modelling, laboratory experiments, and sedimentary field records. Coupled numerical hydrodynamic and boulder transport models (BTM) are widely applied for analysing the impact characteristics of the transport by tsunami, such as wave height and flow velocity. Numerical models able to simulate past tsunami events and the corresponding boulder transport patterns with high accuracy and acceptable computational effort can be utilized as powerful forecasting models predicting the impact of a coast approaching tsunami. We have conducted small-scale physical experiments in the tilting flume with real shaped boulder models. Utilizing the structure from motion technique (Westoby et al., 2012) we reconstructed real boulders from a field study on the Island of Bonaire (Lesser Antilles, Caribbean Sea, Engel & May, 2012). The obtained three-dimensional boulder meshes are utilized for creating downscaled replica of the real boulder for physical experiments. The results of the irregular shaped boulder are compared to experiments with regular shaped boulder models to achieve a better insight about the shape related influence on transport patterns. The numerical model is based on the general two-phase mass flow model by Pudasaini (2012) enhanced for boulder transport simulations. The boulder is implemented using the immersed boundary technique (Peskin, 2002) and the direct forcing approach. In this method Cartesian grids (fluid and particle phase) and Lagrangian meshes (boulder) are combined. By applying the

  2. Numerical investigation of fluid mud motion using a three-dimensional hydrodynamic and two-dimensional fluid mud coupling model

    Science.gov (United States)

    Yang, Xiaochen; Zhang, Qinghe; Hao, Linnan

    2015-03-01

    A water-fluid mud coupling model is developed based on the unstructured grid finite volume coastal ocean model (FVCOM) to investigate the fluid mud motion. The hydrodynamics and sediment transport of the overlying water column are solved using the original three-dimensional ocean model. A horizontal two-dimensional fluid mud model is integrated into the FVCOM model to simulate the underlying fluid mud flow. The fluid mud interacts with the water column through the sediment flux, current, and shear stress. The friction factor between the fluid mud and the bed, which is traditionally determined empirically, is derived with the assumption that the vertical distribution of shear stress below the yield surface of fluid mud is identical to that of uniform laminar flow of Newtonian fluid in the open channel. The model is validated by experimental data and reasonable agreement is found. Compared with numerical cases with fixed friction factors, the results simulated with the derived friction factor exhibit the best agreement with the experiment, which demonstrates the necessity of the derivation of the friction factor.

  3. Boulder emplacement and remobilisation by cyclone and submarine landslide tsunami waves near Suva City, Fiji

    Science.gov (United States)

    Lau, A. Y. Annie; Terry, James P.; Ziegler, Alan; Pratap, Arti; Harris, Daniel

    2018-02-01

    The characteristics of a reef-top boulder field created by a local submarine landslide tsunami are presented for the first time. Our examination of large reef-derived boulders deposited by the 1953 tsunami near Suva City, Fiji, revealed that shorter-than-normal-period tsunami waves generated by submarine landslides can create a boulder field resembling a storm boulder field due to relatively short boulder transport distances. The boulder-inferred 1953 tsunami flow velocity is estimated at over 9 m s- 1 at the reef edge. Subsequent events, for example Cyclone Kina (1993), appear to have remobilised some large boulders. While prior research has demonstrated headward retreat of Suva Canyon in response to the repeated occurrence of earthquakes over the past few millennia, our results highlight the lingering vulnerability of the Fijian coastlines to high-energy waves generated both in the presence (tsunami) and absence (storm) of submarine failures and/or earthquakes. To explain the age discrepancies of U-Th dated coral comprising the deposited boulders, we introduce a conceptual model showing the role of repeated episodes of tsunamigenic submarine landslides in removing reef front sections through collapse. Subsequent high-energy wave events transport boulders from exposed older sections of the reef front onto the reef where they are deposited as 'new' boulders, alongside freshly detached sections of the living reef. In similar situations where anachronistic deposits complicate the deposition signal, age-dating of the coral boulders should not be used as a proxy for determining the timing of the submarine landslides or the tsunamis that generated them.

  4. Mud extrusion and ring-fault gas seepage - upward branching fluid discharge at a deep-sea mud volcano.

    Science.gov (United States)

    Loher, M; Pape, T; Marcon, Y; Römer, M; Wintersteller, P; Praeg, D; Torres, M; Sahling, H; Bohrmann, G

    2018-04-19

    Submarine mud volcanoes release sediments and gas-rich fluids at the seafloor via deeply-rooted plumbing systems that remain poorly understood. Here the functioning of Venere mud volcano, on the Calabrian accretionary prism in ~1,600 m water depth is investigated, based on multi-parameter hydroacoustic and visual seafloor data obtained using ship-borne methods, ROVs, and AUVs. Two seepage domains are recognized: mud breccia extrusion from a summit, and hydrocarbon venting from peripheral sites, hosting chemosynthetic ecosystems and authigenic carbonates indicative of long-term seepage. Pore fluids in freshly extruded mud breccia (up to 13 °C warmer than background sediments) contained methane concentrations exceeding saturation by 2.7 times and chloride concentrations up to five times lower than ambient seawater. Gas analyses indicate an underlying thermogenic hydrocarbon source with potential admixture of microbial methane during migration along ring faults to the peripheral sites. The gas and pore water analyses point to fluids sourced deep (>3 km) below Venere mud volcano. An upward-branching plumbing system is proposed to account for co-existing mud breccia extrusion and gas seepage via multiple surface vents that influence the distribution of seafloor ecosystems. This model of mud volcanism implies that methane-rich fluids may be released during prolonged phases of moderate activity.

  5. The Role of Porosity in the Formation of Coastal Boulder Deposits - Hurricane Versus Tsunami

    Science.gov (United States)

    Spiske, M.; Boeroecz, Z.; Bahlburg, H.

    2007-12-01

    Coastal boulder deposits are a consequence of high-energy wave impacts, such as storms, hurricanes or tsunami. Distinguishing parameters between storm, hurricane and tsunami origin are distance of a deposit from the coast, boulder weight and inferred wave height. Formulas to calculate minimum wave heights of both storm and tsunami waves depend on accurate determination of boulder dimensions and lithology from the respective deposits. At present however, boulder porosity appears to be commonly neglected, leading to significant errors in determined bulk density, especially when boulders consist of reef or coral limestone. This limits precise calculations of wave heights and hampers a clear distinction between storm, hurricane and tsunami origin. Our study uses Archimedean and optical 3D-profilometry measurements for the determination of porosities and bulk densities of reef and coral limestone boulders from the islands of Aruba, Bonaire and Curaçao (ABC Islands, Netherlands Antilles). Due to the high porosities (up to 68 %) of the enclosed coral species, the weights of the reef rock boulders are as low as 20 % of previously calculated values. Hence minimum calculated heights both for tsunami and hurricane waves are smaller than previously proposed. We show that hurricane action appears to be the likely depositional mechanism for boulders on the ABC Islands, since 1) our calculations result in tsunami wave heights which do not permit the overtopping of coastal platforms on the ABC Islands, 2) boulder fields lie on the windward (eastern) sides of the islands, 3) recent hurricanes transported boulders up to 35 m3 and 4) the scarcity of tsunami events affecting the coasts of the ABC Islands compared to frequent impacts of tropical storms and hurricanes.

  6. Mud volcanism of South-Caspian depression

    International Nuclear Information System (INIS)

    Aliyev, A.A.

    2002-01-01

    Full text : South-Caspian depression is presented by area of large warping with thick (more than 25 km) sedimentary series and with wide development of mud volcanism. This depression is unique according to its number of mud volcanoes and intensity of their eruptions. There are about 400 mud volcanoes in this area, which is more than than a half of all volcanoes of the planet. Among them - 220 are continental, more 170 are marine, defined by different methods in the South-Caspian aquatorium. As a result of mudvolcanic activity islands, banks, shoals and underwater ridges are formed in marine conditions. Depths of underwater volcanoes vary from few meters to 900 m as the height of cones are different too. Marine mud volcanoes in geological history of Caspian sea evolution and in its recent history had and important significance. Activity of mud volcanoes in sea conditions lead to the formation of positive elements of relief. Products of ejection take part in the formation of microrelief of surrounding areas of sea bottom influence upon its dynamics and composition of bottom sediments. The carried out comparative analysis of mud volcanism manifestation both onshore and offshore showed the basic differences and similarities in morphology of volcanoes and geology-geochemical peculiarities of eruption products. New data on tectonics of mud volcanism development has been obtained over recent years. Mud volcanoes of South-Caspian depression are studied for assessment and oil-gas content of deep-seated deposits. Geochemical method of search of oil and gas deposits in mudvolcanic areas had been worked out.

  7. Organic chemical composition of mud from the LUSI mud volcano, Sidoarjo, East Java, Indonesia

    Science.gov (United States)

    Rosenbauer, R. J.; Campbell, P.; Lam, A.

    2009-12-01

    Sidoarjo, East Java, Indonesia is the site of LUSI, a terrestrial mud volcano that has been erupting since May 29, 2006. In response to a U.S. Department of State request, the U.S. Geological Survey has been assisting the Indonesian Government to describe the geological and geochemical aspects and potential health risk of the mud eruption. We report here on the organic chemical composition of the mud. Organic chemical analyses were carried out by gas chromatography/mass spectroscopy following organic extraction by microwave-assisted solvent extraction and compound fractionation by adsorption chromatography. There is a petroliferous component in the mud that is fresh, immature, and nonbiodegraded. There is a complete suite of n-alkanes with a bell-shaped pattern typical of fresh petroleum with a Cmax around C20. The alkane content ranges from 0.12 to 1.01 mg/kg dry mud. The presence of certain hopanes (i.e. 17 α,21β(H)-30-norhopane and 17α,21β(H)-hopane) is also indicative of the presence of oil. The proportions of other biomarker compounds (pristane/phytane = 2.4) and the dominance of the C27 sterane (5α(H),14α(H),17α(H)-chlolestane) suggest that oil formed under oxic conditions and has a likely coastal marine or terrigenous source. The presence of oleanane indicates a Cretaceous or younger age for the petrogenic material. These geochemical parameters are consistent with Indonesian oil derived from Tertiary marlstone source rocks that contained kerogen deposited under oxic conditions, probably the upper Miocene Klasafet Formation. Polycyclic aromatic hydrocarbons (PAHs) are present and range in content from 0.1 to 2.2 mg/kg dry mud. The low molecular weight (LMW) PAHs, in particular, naphthalene and methyl-naphthalene are dominant except for perylene which is ubiquitous in the environment. The presence of both parent and higher homologue PAHs indicate a petrogenic rather than combustion source. PAHs are known carcinogens but toxicity data in sediments are

  8. Calcification–carbonation method for red mud processing

    Energy Technology Data Exchange (ETDEWEB)

    Li, Ruibing [School of Metallurgy, Northeastern University, Shenyang 110819 (China); Laboratory for Simulation and Modelling of Particulate Systems, Department of Chemical Engineering, Monash University, Clayton, Victoria, 3800 (Australia); Zhang, Tingan, E-mail: zhangta@smm.neu.edu.cn [School of Metallurgy, Northeastern University, Shenyang 110819 (China); Liu, Yan; Lv, Guozhi; Xie, Liqun [School of Metallurgy, Northeastern University, Shenyang 110819 (China)

    2016-10-05

    Highlights: • A new approach named calcification–carbonation method for red mud processing is proposed. • The method can prevent emission of red mud from alumina production and is good for the environment. • Thermodynamics characteristics were investigated. • The method was verified experimentally using a jet-flow reactor. - Abstract: Red mud, the Bayer process residue, is generated from alumina industry and causes environmental problem. In this paper, a novel calcification–carbonation method that utilized a large amount of the Bayer process residue is proposed. Using this method, the red mud was calcified with lime to transform the silicon phase into hydrogarnet, and the alkali in red mud was recovered. Then, the resulting hydrogarnet was decomposed by CO{sub 2} carbonation, affording calcium silicate, calcium carbonate, and aluminum hydroxide. Alumina was recovered using an alkaline solution at a low temperature. The effects of the new process were analyzed by thermodynamics analysis and experiments. The extraction efficiency of the alumina and soda obtained from the red mud reached 49.4% and 96.8%, respectively. The new red mud with <0.3% alkali can be used in cement production. Using a combination of this method and cement production, the Bayer process red mud can be completely utilized.

  9. Radionuclides in redistributed sediments and ash from the Las Conchas fire in Northern New Mexico

    International Nuclear Information System (INIS)

    Matteson, B.S.; Oldham, Jr.W.J.

    2013-01-01

    The 2011 Las Conchas fire burned 632 km 2 of ponderosa pine forests and pinon-juniper woodlands in the Jemez Mountains in north central New Mexico. In the weeks following the fire, heavy rainfall caused extensive flooding and erosion of surface soil and ash from the affected areas. Samples from mud and ash flows were collected and analyzed for 137 Cs and Pu, which were originally deposited as global fallout during the era of atmospheric nuclear testing. The mean concentrations for 238 Pu, 239,240 Pu and 137 Cs were 0.18 ± 0.05, 4.16 ± 1.95, and 111 ± 56 mBq/g, respectively. 239,240 Pu and 137 Cs are significantly elevated above non-fire affected regional background levels. (author)

  10. Assessing the role of coastal characteristics in erosional process of rocky shores by boulder quarrying.

    Science.gov (United States)

    Causon Deguara, Joanna; Gauci, Ritienne

    2017-04-01

    Rocky coasts are considered as relatively stable coastlines, subject to erosional processes that change the landscape over long periods of time. Block quarrying is one such process, occurring when hydraulic pressure from wave impact dislodges boulders from within the outcropping bedrock. These dislodged boulders can be either deposited inland or dragged seaward by further wave action. This process can be evidenced from boulder deposits on the coast, as well as sockets and detachment scarps that are identified at the shoreline and in the backshore. This study seeks to identify the role of attributes such as aspect, geological structure and water depth have on erosion of rocky coasts through boulder quarrying processes. This is being done through observation of coastline morphology and an analysis of boulder accumulations and erosional features identified on a 3km stretch of rocky shore. The study area is situated on the SE coast of the Island of Malta (Central Mediterranean). The coastline being analysed generally trends NW - SE and consists of a series of limestone beds that dip slightly towards the NE. The boulder deposits observed along the site vary in size, quantity and position with respect to the shoreline. Whilst some areas exhibit large boulder accumulations, other areas are distinguished by the complete absence of such deposits. Taking into consideration the wave climate, the variable size, quantity and distribution of boulder accumulations observed along the site may indicate that geological structure and aspect play an important role in boulder dislodgment by wave action. Key words: rock coast, boulder quarrying, erosional process, Malta

  11. Lahar—River of volcanic mud and debris

    Science.gov (United States)

    Major, Jon J.; Pierson, Thomas C.; Vallance, James W.

    2018-05-09

    Lahar, an Indonesian word for volcanic mudflow, is a mixture of water, mud, and volcanic rock flowing swiftly along a channel draining a volcano. Lahars can form during or after eruptions, or even during periods of inactivity. They are among the greatest threats volcanoes pose to people and property. Lahars can occur with little to no warning, and may travel great distances at high speeds, destroying or burying everything in their paths.Lahars form in many ways. They commonly occur when eruptions melt snow and ice on snow-clad volcanoes; when rains fall on steep slopes covered with fresh volcanic ash; when crater lakes, volcano glaciers or lakes dammed by volcanic debris suddenly release water; and when volcanic landslides evolve into flowing debris. Lahars are especially likely to occur at erupting or recently active volcanoes.Because lahars are so hazardous, U.S. Geological Survey scientists pay them close attention. They study lahar deposits and limits of inundation, model flow behavior, develop lahar-hazard maps, and work with community leaders and governmental authorities to help them understand and minimize the risks of devastating lahars.

  12. Stockpiling and Comprehensive Utilization of Red Mud Research Progress

    Science.gov (United States)

    Liu, Dong-Yan; Wu, Chuan-Sheng

    2012-01-01

    With increasing production of red mud, the environmental problems caused by it are increasingly serious, and thus the integrated treatment of red mud is imminent. This article provides an overview of the composition and the basic characteristics of red mud. The research progress of safe stockpiling and comprehensive utilization of red mud is summarized. The safe stockpiling of red mud can be divided into two aspects: the design and safe operation of the stocking yard. The comprehensive utilization of red mud can be further divided into three aspects: the effective recycling of components, resource utilization and application in the field of environmental protection. This paper points out that the main focus of previous studies on red mud stockpiling is cost reproduction and land tenure. The recovery of resources from red mud has a high value-added, but low level industrialization. The use of red mud as a building material and filler material is the most effective way to reduce the stockpiling of red mud. Red mud used for environmental remediation materials is a new hotspot and worth promoting for its simple processing and low cost.

  13. METHODS OF IMPROVING THE MUD PUMP VALVE LIFE

    Directory of Open Access Journals (Sweden)

    Miruna BĂLTĂREȚU IANCU

    2015-11-01

    Full Text Available Petroleum drilling rigs are used for identifying geologic reservoirs and for creating wells for extraction. The mud pumps of drilling rigs are operated at high mud rates to make possible the drilling process. The durability of the mud pump valves to erosive wear, due to the action of abrasive drilling fluid containing solid particles, depends on their constructive form and on the mud flow velocity. This paper analyzes a few methods of increasing the wear resistance of mud pump valves.

  14. Modeling of Mud-Wave Interaction: Mud-Induced Wave Transport & Wave-Induced Mud Transport

    National Research Council Canada - National Science Library

    Winterwerp, Johan C

    2007-01-01

    .... Also a new rheological model has been proposed to describe liquefaction of soft mud by waves, and the subsequent strength recovery after the passage of the waves. A scheme is presented on how to implement these formulations in Delft3D.

  15. Global and local re-impact and velocity regime of ballistic ejecta of boulder craters on Ceres

    Science.gov (United States)

    Schulzeck, F.; Schröder, S. E.; Schmedemann, N.; Stephan, K.; Jaumann, R.; Raymond, C. A.; Russell, C. T.

    2018-04-01

    Imaging by the Dawn-spacecraft reveals that fresh craters on Ceres below 40 km often exhibit numerous boulders. We investigate how the fast rotating, low-gravity regime on Ceres influences their deposition. We analyze size-frequency distributions of ejecta blocks of twelve boulder craters. Global and local landing sites of boulder crater ejecta and boulder velocities are determined by the analytical calculation of elliptic particle trajectories on a rotating body. The cumulative distributions of boulder diameters follow steep-sloped power-laws. We do not find a correlation between boulder size and the distance of a boulder to its primary crater. Due to Ceres' low gravitational acceleration and fast rotation, ejecta of analyzed boulder craters (8-31 km) can be deposited across the entire surface of the dwarf planet. The particle trajectories are strongly influenced by the Coriolis effect as well as the impact geometry. Fast ejecta of high-latitude craters accumulate close to the pole of the opposite hemisphere. Fast ejecta of low-latitude craters wraps around the equator. Rotational effects are also relevant for the low-velocity regime. Boulders are ejected at velocities up to 71 m/s.

  16. Boulder coastal deposits at Favignana Island rocky coast (Sicily, Italy): Litho-structural and hydrodynamic control

    Science.gov (United States)

    Pepe, Fabrizio; Corradino, Marta; Parrino, Nicolò; Besio, Giovanni; Presti, Valeria Lo; Renda, Pietro; Calcagnile, Lucio; Quarta, Gianluca; Sulli, Attilio; Antonioli, Fabrizio

    2018-02-01

    Boulders are frequently dislodged from rock platforms, transported and deposited along coastal zones by high-magnitude storm waves or tsunamis. Their size and shape are often controlled by the thickness of bedding planes as well as by high-angle to bedding fracture network. We investigate these processes along two coastal areas of Favignana Island by integrating geological data for 81 boulders, 49 rupture surfaces (called sockets) and fracture orientation and spacing with four radiocarbon dates, numerical hydrodynamic analysis, and hindcast numerical simulation data. Boulders are scattered along the carbonate platform as isolated blocks or in small groups, which form, as a whole, a discontinuous berm. Underwater surveys also highlight free boulders with sharp edges and sockets carved out in the rock platform. Boulders are composed of ruditic- to arenitic-size clastic carbonates. Their size ranges from 0.6 to 3.7 m, 0.55 to 2.4 m, and 0.2 to 1 m on the major (A), medium (B), and minor (C) axes, respectively. The highest value of mass estimation is 12.5 t. Almost all of boulders and sockets are characterized by a tabular or bladed shape. The comparisons between a) the fractures spacing and the length of A- and B-axes, and b) the frequency peaks of C-axis with the recurrent thickness of beds measured along the coastal zone demonstrate the litho-structural control in the size and shape of joint-bounded boulders. These comparisons, together with the similarity between the shapes of the boulders and those of the sockets as well as between the lithology of boulders and the areas surrounding the sockets, suggest that blocks originate by detachment from the platform edge. Thus, the most common pre-transport setting is the joint-bounded scenario. Hydrodynamic equations estimate that the storm wave heights necessary to initiate the transport of blocks diverge from 2 m to 8 m for joint-bounded boulders and from few tens of centimeters up to 11 m for submerged boulders. The

  17. Bulk additive system reduces mud costs and waste

    International Nuclear Information System (INIS)

    Wisnie, A.P.

    1994-01-01

    Today, personnel safety and environmental acceptability are high priorities in oil and gas operations. Many advances have been made, but packaging and handling of drilling mud has not changed in 35 years. In most cases, bulk barite is available, however, drilling muds are typically built from chemicals contained in 50 to 100-lb sacks or 5-gal buckets. Materials must be physically opened by rig personnel and mixed into drilling mud. Chemical exposure liability, and lifting or housekeeping related injuries associated with large quantities of packaging pose serious occupational safety risk. Figures from OSHA (1986) indicate that of 1,492 serious injury cases in Louisiana oil and gas operations, 42% were to back and lower extremities, 3% were eye injuries and 1% were chemical burns. Although exact figures are not available, experience suggests that a significant number of injuries are related to mud product physical handling. Another problem with current mud packaging is generated waste. Mud material lost because of broken sacks, inefficient transfer and as residue is unacceptable. Most mud engineers agree that 5 to 15% of mud products are lost or damaged on typical offshore jobs, depending on weather. When material that is spilled or left in packages, probably 2 to 3%, is added, the total is significant. Reusable containers for drilling mud products and manifold system design effectively eliminate these problems

  18. Utilization of red mud and Pb/Zn smelter waste for the synthesis of a red mud-based cementitious material.

    Science.gov (United States)

    Li, Yuan-Cheng; Min, Xiao-Bo; Ke, Yong; Chai, Li-Yuan; Shi, Mei-Qing; Tang, Chong-Jian; Wang, Qing-Wei; Liang, Yan-Jie; Lei, Jie; Liu, De-Gang

    2018-02-15

    A new method in which Pb/Zn smelter waste containing arsenic and heavy metals (arsenic sludge), red mud and lime are utilized to prepare red mud-based cementitious material (RCM) is proposed in this study. XRD, SEM, FTIR and unconfined compressive strength (UCS) tests were employed to assess the physicochemical properties of RCM. In addition, ettringite and iron oxide-containing ettringite were used to study the hydration mechanism of RCM. The results show that the UCS of the RCM (red mud+arsenic sludge+lime) was higher than that of the binder (red mud+arsenic sludge). When the mass ratio of m (binder): m (lime) was 94:6 and then maintained 28days at ambient temperature, the UCS reached 12.05MPa. The red mud has potential cementitious characteristics, and the major source of those characteristics was the aluminium oxide. In the red mud-arsenic sludge-lime system, aluminium oxide was effectively activated by lime and gypsum to form complex hydration products. Some of the aluminium in ettringite was replaced by iron to form calcium sulfoferrite hydrate. The BCR and leaching toxicity results show that the leaching concentration was strongly dependent on the chemical speciation of arsenic and the hydration products. Therefore, the investigated red mud and arsenic sludge can be successfully utilized in cement composites to create a red mud-based cementitious material. Copyright © 2017 Elsevier B.V. All rights reserved.

  19. Gulf of Mexico mud toxicity limitations

    Energy Technology Data Exchange (ETDEWEB)

    Dunn, H.E.; Beardmore, D.H. (Phillips Petroleum Co., Bartlesville, OK (USA)); Stewart, W.S. (Drilling Specialties Co. (US))

    1989-10-01

    Because of the Environmental Protection Agency's recent toxicity limits on drilling mud discharges for offshore Gulf of Mexico, Phillips Petroleum conducted a mud toxicity study based on both field and lab tests. The study, discussed in this article, found the polyanionic cellulose-sulfomethylated quebracho-chrome lignosulfonate mud Phillips had been using would comfortably pass the toxicity limitations. The study also found barite and thinners were of low toxicity, and hydrocarbons and surfactants were highly toxic.

  20. Ca(2+) and OH(-) release of ceramsites containing anorthite and gehlenite prepared from waste lime mud.

    Science.gov (United States)

    Qin, Juan; Yang, Chuanmeng; Cui, Chong; Huang, Jiantao; Hussain, Ahmad; Ma, Hailong

    2016-09-01

    Lime mud is a kind of solid waste in the papermaking industry, which has been a source of serious environmental pollution. Ceramsites containing anorthite and gehlenite were prepared from lime mud and fly ash through the solid state reaction method at 1050°C. The objective of this study was to explore the efficiency of Ca(2+) and OH(-) release and assess the phosphorus and copper ion removal performance of the ceramsites via batch experiments, X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that Ca(2+) and OH(-) were released from the ceramsites due to the dissolution of anorthite, gehlenite and available lime. It is also concluded that gehlenite had stronger capacity for Ca(2+) and OH(-) release compared with anorthite. The Ca(2+) release could be fit well by the Avrami kinetic model. Increases of porosity, dosage and temperature were associated with increases in the concentrations of Ca(2+) and OH(-) released. Under different conditions, the ceramsites could maintain aqueous solutions in alkaline conditions (pH=9.3-10.9) and the release of Ca(2+) was not affected. The removal rates of phosphorus and copper ions were as high as 96.88% and 96.81%, respectively. The final pH values of both phosphorus and copper ions solutions changed slightly. The reuse of lime mud in the form of ceramsites is an effective strategy. Copyright © 2016. Published by Elsevier B.V.

  1. Preliminary study of uranium favorability of the Boulder batholith, Montana

    International Nuclear Information System (INIS)

    Castor, S.B.; Robins, J.W.

    1978-01-01

    The Boulder batholith of southwestern Montana is a composite Late Cretaceous intrusive mass, mostly composed of quartz monzonite and granodiorite. This study was not restricted to the plutonic rocks; it also includes younger rocks that overlie the batholith, and older rocks that it intrudes. The Boulder batholith area has good overall potential for economic uranium deposits, because its geology is similar to that of areas that contain economic deposits elsewhere in the world, and because at least 35 uranium occurrences of several different types are present. Potential is greatest for the occurrence of small uranium deposits in chalcedony veins and base-metal sulfide veins. Three areas may be favorable for large, low-grade deposits consisting of a number of closely spaced chalcedony veins and enriched wall rock; the Mooney claims, the Boulder area, and the Clancy area. In addition, there is a good possibility of by-product uranium production from phosphatic black shales in the project area. The potential for uranium deposits in breccia masses that cut prebatholith rocks, in manganese-quartz veins near Butte, and in a shear zone that cuts Tertiary rhyolite near Helena cannot be determined on the basis of available information. Low-grade, disseminated, primary uranium concentrations similar to porphyry deposits proposed by Armstrong (1974) may exist in the Boulder batholith, but the primary uranium content of most batholith rocks is low. The geologic environment adjacent to the Boulder batholith is similar in places to that at the Midnite mine in Washington. Some igneous rocks in the project area contain more than 10 ppM U 3 O 8 , and some metasedimentary rocks near the batholith contain reductants such as sulfides and carbonaceous material

  2. Geohazard reconnaissance mapping for potential rock boulder fall using low altitude UAV photogrammetry

    Science.gov (United States)

    Sharan Kumar, N.; Ashraf Mohamad Ismail, Mohd; Sukor, Nur Sabahiah Abdul; Cheang, William

    2018-05-01

    This paper discusses potential applications of unmanned aerial vehicles (UAVs) for evaluation of risk immediately with photos and 3-dimensional digital element. Aerial photography using UAV ready to give a powerful technique for potential rock boulder fall recognition. High-resolution outputs from this method give the chance to evaluate the site for potential rock boulder falls spatially. The utilization of UAV to capture the aerial photos is a quick, reliable, and cost-effective technique contrasted with terrestrial laser scanning method. Reconnaissance of potential rock boulder susceptible to fall is very crucial during the geotechnical investigation. This process is essential in the view of the rock fall hazards nearby site before the beginning of any preliminary work. Photogrammetric applications have empowered the automated way to deal with identification of rock boulder susceptible to fall by recognizing the location, size, and position. A developing examination of the utilization of digital photogrammetry gives numerous many benefits for civil engineering application. These advancements have made important contributions to our capabilities to create the geohazard map on potential rock boulder fall.

  3. Boulder Capture System Design Options for the Asteroid Robotic Redirect Mission Alternate Approach Trade Study

    Science.gov (United States)

    Belbin, Scott P.; Merrill, Raymond G.

    2014-01-01

    This paper presents a boulder acquisition and asteroid surface interaction electromechanical concept developed for the Asteroid Robotic Redirect Mission (ARRM) option to capture a free standing boulder on the surface of a 100 m or larger Near Earth Asteroid (NEA). It details the down select process and ranking of potential boulder capture methods, the evolution of a simple yet elegant articulating spaceframe, and ongoing risk reduction and concept refinement efforts. The capture system configuration leverages the spaceframe, heritage manipulators, and a new microspine technology to enable the ARRM boulder capture. While at the NEA it enables attenuation of terminal descent velocity, ascent to escape velocity, boulder collection and restraint. After departure from the NEA it enables, robotic inspection, sample caching, and crew Extra Vehicular Activities (EVA).

  4. Mud dynamics on the shoreface and upper shelf, Noordwijk, The Netherlands

    NARCIS (Netherlands)

    Kleinhans, M.G.; Montfort, O.; Dankers, P.J.T.; Rijn, L.C. van; Bonne, W.

    2005-01-01

    Mud dynamics on the shoreface were studied with measured mud concentrations in the water related to hydrodynamics and measured mud concentrations in the sandy bed. In addition, mud infiltration into the bed was modelled and mud inmixing into the bed by macro-benthos was assessed. The mud

  5. Clay mineralogy of the mud banks of Cochin

    Digital Repository Service at National Institute of Oceanography (India)

    Nair, R.R.; Murty, P.S.N.

    The mineralogy of the sediments constituting the mud banks formed off Cochin, Kerala, India was studied. The clay mineral composition was used as a means of understanding the nature and source of origin of the muds. Fine fraction of the mud samples...

  6. Mud volcanos and mud domes of the central Mediterranean Ridge: near bottom and in situ observations

    NARCIS (Netherlands)

    Huguen, C.; Mascle, J.; Woodside, J.M.; Zitter, T.A.C.; Foucher, J.-P.

    2005-01-01

    The first high-resolution mapping of mud volcanoes and mud domes of the Central Mediterranean Ridge (Eastern Mediterranean) presented here is based on successive in situ observations from the Nautile submersible [MEDINAUT (1998) and NAUTINIL (2003) surveys] and near-bottom side-scan sonar data

  7. Hyperspectral remote sensing and mud volcanism in Azerbaijan

    NARCIS (Netherlands)

    Scholte, K.H.

    2005-01-01

    The fact that Azerbaijan mud volcanoes are closely associated with oil and gas makes their study and identification of the physical and chemical properties of insitu mud volcano surfaces important. Although the composition of in-situ mud volcano surfaces can be highly variable, it usually

  8. Boulder Food Rescue: An Innovative Approach to Reducing Food Waste and Increasing Food Security.

    Science.gov (United States)

    Sewald, Craig A; Kuo, Elena S; Dansky, Hana

    2018-05-01

    Food waste and food insecurity are both significant issues in communities throughout the U.S., including Boulder, Colorado. As much as 40% of the food produced in the U.S. goes uneaten and ends up in landfills. Nearly 13% of people in the Boulder region experience some level of food insecurity. Founded in 2011, Boulder Food Rescue supports community members to create their own food security through a participatory approach to an emergency food system. The organization uses a web-application "robot" to manage a schedule of volunteers. They coordinate with individuals at low-income senior housing sites, individual housing sites, family housing sites, after-school programs, and pre-schools to set up no-cost grocery programs stocked with food from local markets and grocers that would otherwise go to waste. Each site coordinator makes decisions about how, when, and where food delivery and distribution will occur. The program also conducts robust, real-time data collection and analysis. Boulder Food Rescue is a member and manager of the Food Rescue Alliance, and its model has been replicated and adapted by other cities, including Denver, Colorado Springs, Seattle, Jackson Hole, Minneapolis, Binghamton, and in the Philippines. Information for this special article was collected through key informant interviews with current and former Boulder Food Rescue staff and document review of Boulder Food Rescue materials. Boulder Food Rescue's open source software is available to other communities; to date, 40 cities have used the tool to start their own food rescue organizations. Boulder Food Rescue hopes to continue spreading this model to other cities that are considering ways to reduce food waste and increase food security. This article is part of a supplement entitled Building Thriving Communities Through Comprehensive Community Health Initiatives, which is sponsored by Kaiser Permanente, Community Health. Copyright © 2018 American Journal of Preventive Medicine. Published by

  9. Distribution and Characteristics of Boulder Halos at High Latitudes on Mars: Ground Ice and Surface Processes Drive Surface Reworking

    Science.gov (United States)

    Levy, J. S.; Fassett, C. I.; Rader, L. X.; King, I. R.; Chaffey, P. M.; Wagoner, C. M.; Hanlon, A. E.; Watters, J. L.; Kreslavsky, M. A.; Holt, J. W.; Russell, A. T.; Dyar, M. D.

    2018-02-01

    Boulder halos are circular arrangements of clasts present at Martian middle to high latitudes. Boulder halos are thought to result from impacts into a boulder-poor surficial unit that is rich in ground ice and/or sediments and that is underlain by a competent substrate. In this model, boulders are excavated by impacts and remain at the surface as the crater degrades. To determine the distribution of boulder halos and to evaluate mechanisms for their formation, we searched for boulder halos over 4,188 High Resolution Imaging Science Experiment images located between 50-80° north and 50-80° south latitude. We evaluate geological and climatological parameters at halo sites. Boulder halos are about three times more common in the northern hemisphere than in the southern hemisphere (19% versus 6% of images) and have size-frequency distributions suggesting recent Amazonian formation (tens to hundreds of millions of years). In the north, boulder halo sites are characterized by abundant shallow subsurface ice and high thermal inertia. Spatial patterns of halo distribution indicate that excavation of boulders from beneath nonboulder-bearing substrates is necessary for the formation of boulder halos, but that alone is not sufficient. Rather, surface processes either promote boulder halo preservation in the north or destroy boulder halos in the south. Notably, boulder halos predate the most recent period of near-surface ice emplacement on Mars and persist at the surface atop mobile regolith. The lifetime of observed boulders at the Martian surface is greater than the lifetime of the craters that excavated them. Finally, larger minimum boulder halo sizes in the north indicate thicker icy soil layers on average throughout climate variations driven by spin/orbit changes during the last tens to hundreds of millions of years.

  10. Preliminary study of uranium favorability of the Boulder batholith, Montana

    Energy Technology Data Exchange (ETDEWEB)

    Castor, S.B.; Robins, J.W.

    1978-01-01

    The Boulder batholith of southwestern Montana is a composite Late Cretaceous intrusive mass, mostly composed of quartz monzonite and granodiorite. This study was not restricted to the plutonic rocks; it also includes younger rocks that overlie the batholith, and older rocks that it intrudes. The Boulder batholith area has good overall potential for economic uranium deposits, because its geology is similar to that of areas that contain economic deposits elsewhere in the world, and because at least 35 uranium occurrences of several different types are present. Potential is greatest for the occurrence of small uranium deposits in chalcedony veins and base-metal sulfide veins. Three areas may be favorable for large, low-grade deposits consisting of a number of closely spaced chalcedony veins and enriched wall rock; the Mooney claims, the Boulder area, and the Clancy area. In addition, there is a good possibility of by-product uranium production from phosphatic black shales in the project area. The potential for uranium deposits in breccia masses that cut prebatholith rocks, in manganese-quartz veins near Butte, and in a shear zone that cuts Tertiary rhyolite near Helena cannot be determined on the basis of available information. Low-grade, disseminated, primary uranium concentrations similar to porphyry deposits proposed by Armstrong (1974) may exist in the Boulder batholith, but the primary uranium content of most batholith rocks is low. The geologic environment adjacent to the Boulder batholith is similar in places to that at the Midnite mine in Washington. Some igneous rocks in the project area contain more than 10 ppM U/sub 3/O/sub 8/, and some metasedimentary rocks near the batholith contain reductants such as sulfides and carbonaceous material.

  11. Cyclic Activity of Mud Volcanoes: Evidences from Trinidad (SE Caribbean)

    Science.gov (United States)

    Deville, E.

    2007-12-01

    Fluid and solid transfer in mud volcanoes show different phases of activity, including catastrophic events followed by periods of relative quiescence characterized by moderate activity. This can be notably shown by historical data onshore Trinidad. Several authors have evoked a possible link between the frequencies of eruption of some mud volcanoes and seismic activity, but in Trinidad there is no direct correlation between mud eruptions and seisms. It appears that each eruptive mud volcano has its own period of catastrophic activity, and this period is highly variable from one volcano to another. The frequency of activity of mud volcanoes seems essentially controlled by local pressure regime within the sedimentary pile. At the most, a seism can, in some cases, activate an eruption close to its term. The dynamics of expulsion of the mud volcanoes during the quiescence phases has been studied notably from temperature measurements within the mud conduits. The mud temperature is concurrently controlled by, either, the gas flux (endothermic gas depressurizing induces a cooling effect), or by the mud flux (mud is a vector for convective heat transfer). Complex temperature distribution was observed in large conduits and pools. Indeed, especially in the bigger pools, the temperature distribution characterizes convective cells with an upward displacement of mud above the deep outlet, and ring-shaped rolls associated with the burial of the mud on the flanks of the pools. In simple, tube-like shaped, narrow conduits, the temperature is more regular, but we observed different types of profiles, with either downward increasing or decreasing temperatures. If the upward flow of mud would be regular, we should expect increasing temperatures and progressively decreasing gradient with depth within the conduits. However, the variable measured profiles from one place to another, as well as time-variable measured temperatures within the conduits and especially, at the base of the

  12. Chemical monitoring of mud products on drilled cuttings

    International Nuclear Information System (INIS)

    Hughes, T.L.; Jones, T.G.J.; Tomkins, P.G.; Gilmour, A.; Houwen, O.H.; Sanders, M.

    1991-01-01

    An increasing area of concern for offshore drilling practices in the environmental impact of discharged drilled cuttings contaminated with drilling fluids. The standard retort analysis is of limited accuracy and chemical specificity. Anticipating future requirements for a more complete accounting of mud chemicals discharged to the environment, we present here results for chemical monitoring using a modern comprehensive chemical analysis technique. Fourier transform infrared (FT-IR) spectrometry. In this paper description is given of sampling methods found to be practical and the main calibration requirements are discussed. The techniques developed in the course of this work give a good mineralogical breakdown of mud solids (commercial and drilled solids) in addition to the environmentally relevant measurements relating to mud on cuttings. The possibility of using the new technique for the rigsite monitoring of drilling cuttings is demonstrated. Cuttings samples simultaneously from the flow line, shaker screen, desilter and mud cleaner were analyzed. It is found that mud polymers and other organic additives can be measured with sufficient accuracy to measure the removal of mud products by discharged cuttings. The technique is also applicable to quantify the losses of oil-based mud on cuttings. Field testing has shown that the instrumentation used in sufficiently robust and simple to use for rig-site application

  13. Geological model for Boulder 1 at Station 2, South Massif, Valley of Taurus-Littrow

    Science.gov (United States)

    Schmitt, H. H.

    1975-01-01

    A possible geological model for the origin and history of the materials that make up Boulder 1 is proposed on the basis of firm and probable regional, local, and boulder geological constraints. These constraints are described in detail, unresolved questions are considered, and a model is presented which appears to satisfy all the firm constraints and most of the probable constraints. According to this model, the crystallization of plagioclase and other ANT-suite phases now present in the boulder as clasts and matrix materials took place during the melted-shell stage of lunar history; the original rocks were greatly modified during the cratered-highland stage; and the events that determined the major characteristics of the boulder occurred during the large-basin stage.

  14. Hidden values in bauxite residue (red mud): Recovery of metals

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Yanju; Naidu, Ravi, E-mail: ravi.naidu@unisa.edu.au

    2014-12-15

    Highlights: • Current iron recovery techniques using red mud are depicted. • Advantages and disadvantages exist in different recovering processes. • Economic and environmental friendly integrated usage of red mud is promising. - Abstract: Bauxite residue (red mud) is a hazardous waste generated from alumina refining industries. Unless managed properly, red mud poses significant risks to the local environment due to its extreme alkalinity and its potential impacts on surface and ground water quality. The ever-increasing generation of red mud poses significant challenges to the aluminium industries from management perspectives given the low proportion that are currently being utilized beneficially. Red mud, in most cases, contains elevated concentrations of iron in addition to aluminium, titanium, sodium and valuable rare earth elements. Given the scarcity of iron supply globally, the iron content of red mud has attracted increasing research interest. This paper presents a critical overview of the current techniques employed for iron recovery from red mud. Information on the recovery of other valuable metals is also reviewed to provide an insight into the full potential usage of red mud as an economic resource rather than a waste. Traditional hydrometallurgy and pyrometallurgy are being investigated continuously. However, in this review several new techniques are introduced that consider the process of iron recovery from red mud. An integrated process which can achieve multiple additional values from red mud is much preferred over the single process methods. The information provided here should help to improve the future management and utilization of red mud.

  15. Hidden values in bauxite residue (red mud): Recovery of metals

    International Nuclear Information System (INIS)

    Liu, Yanju; Naidu, Ravi

    2014-01-01

    Highlights: • Current iron recovery techniques using red mud are depicted. • Advantages and disadvantages exist in different recovering processes. • Economic and environmental friendly integrated usage of red mud is promising. - Abstract: Bauxite residue (red mud) is a hazardous waste generated from alumina refining industries. Unless managed properly, red mud poses significant risks to the local environment due to its extreme alkalinity and its potential impacts on surface and ground water quality. The ever-increasing generation of red mud poses significant challenges to the aluminium industries from management perspectives given the low proportion that are currently being utilized beneficially. Red mud, in most cases, contains elevated concentrations of iron in addition to aluminium, titanium, sodium and valuable rare earth elements. Given the scarcity of iron supply globally, the iron content of red mud has attracted increasing research interest. This paper presents a critical overview of the current techniques employed for iron recovery from red mud. Information on the recovery of other valuable metals is also reviewed to provide an insight into the full potential usage of red mud as an economic resource rather than a waste. Traditional hydrometallurgy and pyrometallurgy are being investigated continuously. However, in this review several new techniques are introduced that consider the process of iron recovery from red mud. An integrated process which can achieve multiple additional values from red mud is much preferred over the single process methods. The information provided here should help to improve the future management and utilization of red mud

  16. Boulder accumulations related to extreme wave events on the eastern coast of Malta

    Science.gov (United States)

    Biolchi, Sara; Furlani, Stefano; Antonioli, Fabrizio; Baldassini, Niccoló; Causon Deguara, Joanna; Devoto, Stefano; Di Stefano, Agata; Evans, Julian; Gambin, Timothy; Gauci, Ritienne; Mastronuzzi, Giuseppe; Monaco, Carmelo; Scicchitano, Giovanni

    2016-03-01

    The accumulation of large boulders related to waves generated by either tsunamis or extreme storm events have been observed in different areas of the Mediterranean Sea. Along the eastern low-lying rocky coasts of Malta, five sites with large boulder deposits have been investigated, measured and mapped. These boulders have been detached and moved from the nearshore and the lowest parts of the coast by sea wave action. In the Sicily-Malta channel, heavy storms are common and originate from the NE and NW winds. Conversely, few tsunamis have been recorded in historical documents to have reached the Maltese archipelago. We present a multi-disciplinary study, which aims to define the characteristics of these boulder accumulations, in order to assess the coastal geo-hazard implications triggered by the sheer ability of extreme waves to detach and move large rocky blocks inland. The wave heights required to transport 77 coastal boulders were calculated using various hydrodynamic equations. Particular attention was given to the quantification of the input parameters required in the workings of these equations, such as size, density and distance from the coast. In addition, accelerator mass spectrometry (AMS) 14C ages were determined from selected samples of marine organisms encrusted on some of the coastal boulders. The combination of the results obtained both by the hydrodynamic equations, which provided values comparable with those observed and measured during the storms, and radiocarbon dating suggests that the majority of the boulders have been detached and moved by intense storm waves. These boulders testify to the existence of a real hazard for the coasts of Malta, i.e. that of very high storm waves, which, during exceptional storms, are able to detach large blocks of volumes exceeding 10 m3 from the coastal edge and the nearshore bottom, and also to transport them inland. Nevertheless, the occurrence of one or more tsunami events cannot be ruled out, since

  17. 3D Modeling of Glacial Erratic Boulders in the Haizi Shan Region, Eastern Tibetan Plateau

    Science.gov (United States)

    Sheriff, M.; Stevens, J.; Radue, M. J.; Strand, P.; Zhou, W.; Putnam, A. E.

    2017-12-01

    The focus of our team's research is to study patterns of glacier retreat in the Northern and Southern Hemispheres at the end of the last ice age. Our purpose is to search for what caused this great global warming. Such information will improve understanding of how the climate system may respond to the human-induced buildup of fossil carbon dioxide. To reconstruct past glacier behavior, we sample boulders deposited by glaciers to find the rate of ancient recession. Each sample is tested to determine the age of the boulder using 10Be cosmogenic-nuclide dating. My portion of this research focuses on creating 3D models of the sampled boulders. Such high-resolution 3D models afford visual inspection and analysis of each boulder in a virtual reality environment after fieldwork is complete. Such detailed virtual reconstructions will aid post-fieldwork evaluation of sampled boulders. This will help our team interpret 10Be dating results. For example, a high-resolution model can aid post-fieldwork observations, and allow scientists to determine whether the rock has been previously covered, eroded, or moved since it was deposited by the glacier, but before the sample was collected. Also a model can be useful for recognizing patterns between age and boulder morphology. Lastly, the models can be used for those who wish to review the data after publication. To create the 3D models, I will use Hero4 GoPro and Canon PowerShot digital cameras to collect photographs of each boulder from different angles. I will then process the digital imagery using `structure-from-motion' techniques and Agisoft Photoscan software. All boulder photographs will be synthesized to 3D and based on a standardized scale. We will then import these models into an environment that can be accessed using cutting-edge virtual reality technology. By producing a virtual archive of 3D glacial boulder reconstructions, I hope to provide deeper insight into geological processes influencing these boulders during and

  18. Monitoring drilling mud composition using flowing liquid junction electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Jasinski, R; Fletcher, P; Vercaemer, C

    1990-06-27

    The concentration of a chosen ionic component of a drilling mud is determined from the potential difference between an ion selective electrode, selective to the component and a reference electrode, the reference electrode being connected to the mud by a liquid junction through which reference electrolyte flows from the electrode to the mud. The system avoids errors due to undesirable interactions between the mud and the reference electrode materials. (author).

  19. Microfossils in the Ordovician erratic boulders from South-western Finland

    Directory of Open Access Journals (Sweden)

    Nõlvak, J.

    1995-12-01

    Full Text Available Chitinozoans, ostracods and acritarchs found in four glacially transported limestone boulders from the south-western coast of Finland have been studied in order to test the usefulness of these microfossil groups in age determinations. Also rare specimens of conodonts, inarticulated brachiopods and foraminifers were found. Baltic limestone (or Östersjö limestone was the most problematic, because only fossils with calcitic or phosphatic shells are preserved. It is concluded that the boulders identified correlate with the Uhaku and Rakvere stages of the Middle Ordovician.

  20. 33 CFR 117.177 - Mud Slough.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 1 2010-07-01 2010-07-01 false Mud Slough. 117.177 Section 117.177 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY BRIDGES DRAWBRIDGE OPERATION REGULATIONS Specific Requirements California § 117.177 Mud Slough. The draw of the Union Pacific...

  1. AudioMUD: a multiuser virtual environment for blind people.

    Science.gov (United States)

    Sánchez, Jaime; Hassler, Tiago

    2007-03-01

    A number of virtual environments have been developed during the last years. Among them there are some applications for blind people based on different type of audio, from simple sounds to 3-D audio. In this study, we pursued a different approach. We designed AudioMUD by using spoken text to describe the environment, navigation, and interaction. We have also introduced some collaborative features into the interaction between blind users. The core of a multiuser MUD game is a networked textual virtual environment. We developed AudioMUD by adding some collaborative features to the basic idea of a MUD and placed a simulated virtual environment inside the human body. This paper presents the design and usability evaluation of AudioMUD. Blind learners were motivated when interacted with AudioMUD and helped to improve the interaction through audio and interface design elements.

  2. Hidden values in bauxite residue (red mud): recovery of metals.

    Science.gov (United States)

    Liu, Yanju; Naidu, Ravi

    2014-12-01

    Bauxite residue (red mud) is a hazardous waste generated from alumina refining industries. Unless managed properly, red mud poses significant risks to the local environment due to its extreme alkalinity and its potential impacts on surface and ground water quality. The ever-increasing generation of red mud poses significant challenges to the aluminium industries from management perspectives given the low proportion that are currently being utilized beneficially. Red mud, in most cases, contains elevated concentrations of iron in addition to aluminium, titanium, sodium and valuable rare earth elements. Given the scarcity of iron supply globally, the iron content of red mud has attracted increasing research interest. This paper presents a critical overview of the current techniques employed for iron recovery from red mud. Information on the recovery of other valuable metals is also reviewed to provide an insight into the full potential usage of red mud as an economic resource rather than a waste. Traditional hydrometallurgy and pyrometallurgy are being investigated continuously. However, in this review several new techniques are introduced that consider the process of iron recovery from red mud. An integrated process which can achieve multiple additional values from red mud is much preferred over the single process methods. The information provided here should help to improve the future management and utilization of red mud. Copyright © 2014 Elsevier Ltd. All rights reserved.

  3. The diversity of mud volcanoes in the landscape of Azerbaijan

    Science.gov (United States)

    Rashidov, Tofig

    2014-05-01

    As the natural phenomenon the mud volcanism (mud volcanoes) of Azerbaijan are known from the ancient times. The historical records describing them are since V century. More detail study of this natural phenomenon had started in the second half of XIX century. The term "mud volcano" (or "mud hill") had been given by academician H.W. Abich (1863), more exactly defining this natural phenomenon. All the previous definitions did not give such clear and capacious explanation of it. In comparison with magmatic volcanoes, globally the mud ones are restricted in distribution; they mainly locate within the Alpine-Himalayan, Pacific and Central Asian mobile belts, in more than 30 countries (Columbia, Trinidad Island, Italy, Romania, Ukraine, Georgia, Azerbaijan, Turkmenistan, Iran, Pakistan, Indonesia, Burma, Malaysia, etc.). Besides it, the zones of mud volcanoes development are corresponded to zones of marine accretionary prisms' development. For example, the South-Caspian depression, Barbados Island, Cascadia (N.America), Costa-Rica, Panama, Japan trench. Onshore it is Indonesia, Japan, and Trinidad, Taiwan. The mud volcanism with non-accretionary conditions includes the areas of Black Sea, Alboran Sea, the Gulf of Mexico (Louisiana coast), Salton Sea. But new investigations reveal more new mud volcanoes and in places which were not considered earlier as the traditional places of mud volcanoes development (e.g. West Nile Rive delta). Azerbaijan is the classic region of mud volcanoes development. From over 800 world mud volcanoes there are about 400 onshore and within the South-Caspian basin, which includes the territory of East Azerbaijan (the regions of Shemakha-Gobustan and Low-Kura River, Absheron peninsula), adjacent water area of South Caspian (Baku and Absheron archipelagoes) and SW Turkmenistan and represents an area of great downwarping with thick (over 25 km) sedimentary series. Generally, in the modern relief the mud volcanoes represent more or less large uplifts

  4. Corrective Action Investigation Plan for Corrective Action Unit 234: Mud Pits, Cellars, and Mud Spills, Nevada Test Site, Nevada, Revision 0

    International Nuclear Information System (INIS)

    Grant Evenson

    2007-01-01

    Corrective Action Unit 234, Mud Pits, Cellars, and Mud Spills, consists of 12 inactive sites located in the north and northeast section of the NTS. The 12 CAU 234 sites consist of mud pits, mud spills, mud sumps, and an open post-test cellar. The CAU 234 sites were all used to support nuclear testing conducted in the Yucca Flat and Rainier Mesa areas during the 1950s through the 1970s. The CASs in CAU 234 are being investigated because hazardous and/or radioactive constituents may be present in concentrations that could potentially pose a threat to human health and the environment. Existing information on the nature and extent of potential contamination is insufficient to evaluate and recommend corrective action alternatives for the CASs. Additional information will be generated by conducting a CAI before evaluating and selecting appropriate corrective action alternatives

  5. A story about distributions of dimensions and locations of boulders

    DEFF Research Database (Denmark)

    Ditlevsen, Ove Dalager

    2006-01-01

    for making a bored tunnel through the till deposit. Geographical universality was discovered through the statistical analysis of observations of boulder coordinates and dimension measures from wide spread cliff beach locations. One conclusion is that the joint size distribution up to some degree of modeling...... distribution. Moreover, these ratios are independent of the maximal dimension. The random point field structure of the boulder coordinates as isolated points or as clusters of points makes Poisson fields reasonable modeling candidates for the fields of both single points and cluster points. The cluster size...

  6. A story about estimation of a random field of boulders from incomplete seismic measurements

    DEFF Research Database (Denmark)

    Ditlevsen, Ove Dalager

    2005-01-01

    deposits along the tunnel line. By use of this important distribution information and of the observed homogeneity of the seismic point source field together with the physical properties of diffraction it became possible to make the wanted prediction. During the excavation the found boulders were counted......This paper reports on the statistical interpretation of seismic diffraction measurements of boulder locations. The measurements are made in a corridor along the planned tunnel line for the later realized bored tunnel through the till deposits under the East Channel of the Great Belt in Denmark...... graphical registrations on seismograms do not make a proper interpretation possible without detailed knowledge about the joint distribution of the primary dimensions of the boulders. Therefore separate measurements were made of the dimensions of boulders deposited visibly on the cliff beaches of the Great...

  7. Thermal mud maturation: organic matter and biological activity.

    Science.gov (United States)

    Centini, M; Tredici, M R; Biondi, N; Buonocore, A; Maffei Facino, R; Anselmi, C

    2015-06-01

    Many of the therapeutic and cosmetic treatments offered in spas are centred on mud therapy, to moisturize the skin and prevent skin ageing and rheumatic diseases. Thermal mud is a complex matrix composed of organic and inorganic elements which contribute to its functions. It is a natural product derived from the long mixing of clay and thermal water. During its maturation, organic substances are provided by the microalgae, which develop characteristic of the composition of thermal water. The aim of this study was to identify methods for introducing objective parameters as a basis for characterizing thermal mud and assessing its efficacy. Samples of thermal mud were collected at the Saturnia spa, where there are several sulphureous pools. The maturation of the mud was evaluated by organic component determination using extractive methods and chromatographic analysis (HPLC, GC-MS, SPME). We also studied the radical scavenging activity of mud samples at different stages of maturation, in a homogeneous phase, using several tests (DPPH, ORAC, ABTS). We identified several classes of compounds: saturated and unsaturated fatty acids, hydroxyl acids, dicarboxylic acids, ketoacids, alcohols and others. SPME analysis showed the presence of various hydrocarbons compounds (C(11) -C(17)) and long-chain alcohols (C(12) -C(16)). Six or seven months seemed appropriate to complete the process of maturation, and the main effect of maturation time was the increase of lipids. Six-month mud showed the highest activity. The hydrophilic extract was more active than the lipophilic extract. The results indicate that maturation of thermal mud can be followed on the basis of the changes in its organic composition and antioxidant properties along the time. They also highlight the need to develop reference standards for thermal muds in relation to assess their use for therapeutic and cosmetic purposes. © 2015 Society of Cosmetic Scientists and the Société Française de Cosmétologie.

  8. Mud Logging; Control geologico en perforaciones petroliferas (Mud Logging)

    Energy Technology Data Exchange (ETDEWEB)

    Pumarega Lafuente, J.C.

    1994-12-31

    Mud Logging is an important activity in the oil field and it is a key job in drilling operations, our duties are the acquisition, collection and interpretation of the geological and engineering data at the wellsite, also inform the client immediately of any significant changes in the well. (Author)

  9. Asteroid Redirect Robotic Mission: Robotic Boulder Capture Option Overview

    Science.gov (United States)

    Mazanek, Daniel D.; Merrill, Raymond G.; Belbin, Scott P.; Reeves, David M.; Earle, Kevin D.; Naasz, Bo J.; Abell, Paul A.

    2014-01-01

    The National Aeronautics and Space Administration (NASA) is currently studying an option for the Asteroid Redirect Robotic Mission (ARRM) that would capture a multi-ton boulder (typically 2-4 meters in size) from the surface of a large (is approximately 100+ meter) Near-Earth Asteroid (NEA) and return it to cislunar space for subsequent human and robotic exploration. This alternative mission approach, designated the Robotic Boulder Capture Option (Option B), has been investigated to determine the mission feasibility and identify potential differences from the initial ARRM concept of capturing an entire small NEA (4-10 meters in size), which has been designated the Small Asteroid Capture Option (Option A). Compared to the initial ARRM concept, Option B allows for centimeter-level characterization over an entire large NEA, the certainty of target NEA composition type, the ability to select the boulder that is captured, numerous opportunities for mission enhancements to support science objectives, additional experience operating at a low-gravity planetary body including extended surface contact, and the ability to demonstrate future planetary defense strategies on a hazardous-size NEA. Option B can leverage precursor missions and existing Agency capabilities to help ensure mission success by targeting wellcharacterized asteroids and can accommodate uncertain programmatic schedules by tailoring the return mass.

  10. Radioactivity of peat mud used in therapy.

    Science.gov (United States)

    Karpińska, Maria; Mnich, Krystian; Kapała, Jacek; Bielawska, Agnieszka; Kulesza, Grzegorz; Mnich, Stanisław

    2016-02-01

    The aim of the study was to determine the contents of natural and artificial isotopes in peat mud and to estimate the radiation dose absorbed via skin in patients during standard peat mud treatment. The analysis included 37 samples collected from 8 spas in Poland. The measurements of isotope concentration activity were conducted with the use of gamma spectrometry methods. The skin dose in a standard peat mud bath therapy is approximately 300 nSv. The effective dose of such therapy is considered to be 22 nSv. The doses absorbed during peat mud therapy are 5 orders of magnitude lower than effective annual dose absorbed from the natural radiation background by a statistical Pole (3.5 mSv). Neither therapeutic nor harmful effect is probable in case of such a small dose of ionising radiation. Copyright © 2015 Elsevier Ltd. All rights reserved.

  11. Treatment of a mud pit by bioremediation.

    Science.gov (United States)

    Avdalović, Jelena; Đurić, Aleksandra; Miletić, Srdjan; Ilić, Mila; Milić, Jelena; Vrvić, Miroslav M

    2016-08-01

    The mud generated from oil and natural gas drilling, presents a considerable ecological problem. There are still insufficient remedies for the removal and minimization of these very stable emulsions. Existing technologies that are in use, more or less successfully, treat about 20% of generated waste drilling mud, while the rest is temporarily deposited in so-called mud pits. This study investigated in situ bioremediation of a mud pit. The bioremediation technology used in this case was based on the use of naturally occurring microorganisms, isolated from the contaminated site, which were capable of using the contaminating substances as nutrients. The bioremediation was stimulated through repeated inoculation with a zymogenous microbial consortium, along with mixing, watering and biostimulation. Application of these bioremediation techniques reduced the concentration of total petroleum hydrocarbons from 32.2 to 1.5 g kg(-1) (95% degradation) during six months of treatment. © The Author(s) 2016.

  12. Experimental study on rule of radioactive change of red mud concrete

    Science.gov (United States)

    Wu, Bin; Tan, Zhuoying; Yu, Zhongtao

    2017-12-01

    Red mud was used to partially replace cement to prepare red mud concrete, with replacement rate of red mud mass being 0%, 5%, 10%, 15% and 20% respectively, and hydration age being 3d, 28d and 90d. The experiment of cube compressive strength and radioactivity were conducted for 90 cubical test pieces respectively. The results show that with rise of replacement rate of red mud, the cube compressive strength of red mud concrete at the same hydration age first increased and then decreased, leading to increase of content of 226Ra,232Th,40K in red mud concrete, and increase of material’s radioactivity accordingly; as hydration age was prolonged, with the replacement rate of red mud being the same, the compressive strength increased, and internal and external exposure indices and total specific activity all increased yet with small increase range. Generally the hydration age does not significantly influence the radioactivity of red mud concrete.

  13. The effects of drilling muds on marine invertebrate larvae and adults

    International Nuclear Information System (INIS)

    Raimondi, P.T.; Barnett, A.M.; Krause, P.R.

    1997-01-01

    A series of laboratory experiments tested the effects of drilling muds from an active platform off southern California on larvae and adults of marine invertebrates. Red abalone (Haliotis rufescens) were used to determine effects of drilling muds on fertilization, early development, survivorship, and settlement, and experiments on adult brown cup corals (Paracyathus stearnsii) tested effects on adult survivorship, viability, and tissue loss. Exposures to drilling muds did not have an effect on abalone fertilization or early development. However, several exposures to drilling muds resulted in weak, but significant, positive effects of drilling muds on settlement of competent larvae. In contrast, settlement of red abalone larvae on natural coralline algal crusts decreased with increasing concentrations of drilling muds. This suggests that drilling muds affect either the abalone's ability to detect natural settlement inducers, or they affect the inducer itself. Exposure of brown cup corals to concentrations of drilling muds adversely impacted their survivorship and viability. These effects were likely caused by increased tissue mortality of the coral polyps

  14. Final Technical Report - Modernization of the Boulder Canyon Hydroelectric Project

    Energy Technology Data Exchange (ETDEWEB)

    Taddeucci, Joe [Dept. of Public Works, Boulder, CO (United States). Utilities Division

    2013-03-29

    The Boulder Canyon Hydroelectric Project (BCH) was purchased by the City of Boulder, CO (the city) in 2001. Project facilities were originally constructed in 1910 and upgraded in the 1930s and 1940s. By 2009, the two 10 MW turbine/generators had reached or were nearing the end of their useful lives. One generator had grounded out and was beyond repair, reducing plant capacity to 10 MW. The remaining 10 MW unit was expected to fail at any time. When the BCH power plant was originally constructed, a sizeable water supply was available for the sole purpose of hydroelectric power generation. Between 1950 and 2001, that water supply had gradually been converted to municipal water supply by the city. By 2001, the water available for hydroelectric power generation at BCH could not support even one 10 MW unit. Boulder lacked the financial resources to modernize the facilities, and Boulder anticipated that when the single, operational historical unit failed, the project would cease operation. In 2009, the City of Boulder applied for and received a U.S. Department of Energy (DOE) grant for $1.18 million toward a total estimated project cost of $5.155 million to modernize BCH. The federal funding allowed Boulder to move forward with plant modifications that would ensure BCH would continue operation. Federal funding was made available through the American Recovery and Reinvestment Act (ARRA) of 2009. Boulder determined that a single 5 MW turbine/generator would be the most appropriate capacity, given the reduced water supply to the plant. Average annual BCH generation with the old 10 MW unit had been about 8,500 MW-hr, whereas annual generation with a new, efficient turbine could average 11,000 to 12,000 MW-hr. The incremental change in annual generation represents a 30% increase in generation over pre-project conditions. The old turbine/generator was a single nozzle Pelton turbine with a 5-to-1 flow turndown and a maximum turbine/generator efficiency of 82%. The new unit is a

  15. Red mud characterization using nuclear analytical techniques

    International Nuclear Information System (INIS)

    Obhodas, J.; Sudac, D.; Matjacic, L.; Valkovic, V.

    2011-01-01

    Red mud is a toxic waste left as a byproduct in aluminum production Bayer process. Since it contains significant concentrations of other chemical elements interesting for industry, including REE, it is also potential secondary ore source. Recent events in some countries have shown that red mud presents a serious environmental hazard if not properly stored. The subject of our study is the red mud from an ex-aluminum plant in Obrovac, Croatia, left from processing of bauxite mined during late 70's and early 80's at the eastern Adriatic coast and since than stored in open concrete basins for more than 30 years. We have used energy dispersive x-ray fluorescence analysis (both tube and radioactive source excitation), fast neutron activation analysis and passive gamma spectrometry to identify a number of elements present in the red mud, their concentration levels and radioactivity in the red mud. The high concentrations of Al, Si, Ca, Ti and Fe have been measured. Chemical elements Sc, Cr, Mn, Co, Ni, Cu, Zn, Ga, As, Se, Br, Y, La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Pb, Th and U were found in lower concentrations. No significant levels of radioactivity have been measured. (authors)

  16. Elementary concentration of Peruibe black mud by neutron activation analysis

    Energy Technology Data Exchange (ETDEWEB)

    Torrecilha, Jefferson K.; Ponciano, Ricardo; Silva, Paulo S.C da, E-mail: jeffkoy@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN-CNEN/SP), Sao Paulo, SP (Brazil)

    2013-07-01

    The Peruibe Black Mud is used in therapies such as psoriasis, peripheral dermatitis, acne, seborrehea, myalgia arthritis and rheumatic non-articular processes. This material is characterized by is fine organic matter particles, sulphate reducing bacteria and a high content of potential reduction ions. Although this material is particles, sulphate reducing bacteria and a high content of potential reduction ions. Although this material is considered natural, it may not be free of possible adverse health effects, like toxic chemical elements, when used for therapeutic purposes. In the therapeutic treatments involving clays, clays are used in mud form also called peloids, obtained by maturation process. Five in natura and three maturated Black Mud samples were collected in Peruibe city, Sao Paulo State, Brazil. To investigate the distribution of major, trace and rare earth elements in the in natura and maturated clays that constitute the Peruibe Black Mud, neutron activation analysis (NAA) was used. A comparison between in natura and maturated mud shows that major, trace and rare earth elements follow the same order in both types. Generally, the concentrations in the maturated mud are slightly lower than in natura mud. Enrichment on the upper continental crust could be observed for the elements As, Br, Sb and Se, in these types of mud. (author)

  17. Aluminium leaching from red mud by filamentous fungi.

    Science.gov (United States)

    Urík, Martin; Bujdoš, Marek; Milová-Žiaková, Barbora; Mikušová, Petra; Slovák, Marek; Matúš, Peter

    2015-11-01

    This contribution investigates the efficient and environmentally friendly aluminium leaching from red mud (bauxite residue) by 17 species of filamentous fungi. Bioleaching experiments were examined in batch cultures with the red mud in static, 7-day cultivation. The most efficient fungal strains in aluminium bioleaching were Penicillium crustosum G-140 and Aspergillus niger G-10. The A. niger G-10 strain was capable to extract up to approximately 141 mg·L(-1) of aluminium from 0.2 g dry weight red mud. Chemical leaching with organic acids mixture, prepared according to A. niger G-10 strain's respective fungal excretion during cultivation, proved that organic acids significantly contribute to aluminium solubilization from red mud. Copyright © 2015 Elsevier Inc. All rights reserved.

  18. New insights into the sorption mechanism of cadmium on red mud

    International Nuclear Information System (INIS)

    Luo Lei; Ma Chenyan; Ma Yibing; Zhang Shuzhen; Lv Jitao; Cui Mingqi

    2011-01-01

    Effectiveness and mechanism of cadmium (Cd) sorption on original, acidified and ball milling nano-particle red muds were investigated using batch sorption experiments, sequential extraction analysis and X-ray absorption near edge structure (XANES) spectroscopy. The maximum sorption capacity of Cd was 0.16, 0.19, and 0.21 mol/kg for the original, acidified, and nano-particle red muds at pH 6.5, respectively. Both acidification and ball-milling treatments significantly enhanced Cd sorption and facilitated transformation of Cd into less extractable fractions. The Cd L III -edge XANES analysis indicated the formation of inner-sphere complexes of Cd similar to XCdOH (X represents surface groups on red mud) on the red mud surfaces although outer-sphere complexes of Cd were the primary species. This work shed light on the potential application of red mud to remediate Cd-contaminated soils and illustrated the promising tool of XANES spectroscopy for speciation of multicomponent systems of environmental relevance. - Graphical abstract: Display Omitted Highlights: → Red mud has a strong affinity for Cd contaminants. → Ball-milling treatments significantly enhance Cd sorption on red mud. → Cadmium partially formed inner-sphere complexes on the red mud surfaces. → Red mud can be used to remediate Cd contaminated soils effectively. - Cadmium can be strongly sorbed and partially forms inner-sphere complexes on red mud.

  19. Giant boulders and Last Interglacial storm intensity in the North Atlantic

    Science.gov (United States)

    Rovere, Alessio; Casella, Elisa; Harris, Daniel L.; Lorscheid, Thomas; Nandasena, Napayalage A. K.; Dyer, Blake; Sandstrom, Michael R.; Stocchi, Paolo; D'Andrea, William J.; Raymo, Maureen E.

    2017-11-01

    As global climate warms and sea level rises, coastal areas will be subject to more frequent extreme flooding and hurricanes. Geologic evidence for extreme coastal storms during past warm periods has the potential to provide fundamental insights into their future intensity. Recent studies argue that during the Last Interglacial (MIS 5e, ˜128–116 ka) tropical and extratropical North Atlantic cyclones may have been more intense than at present, and may have produced waves larger than those observed historically. Such strong swells are inferred to have created a number of geologic features that can be observed today along the coastlines of Bermuda and the Bahamas. In this paper, we investigate the most iconic among these features: massive boulders atop a cliff in North Eleuthera, Bahamas. We combine geologic field surveys, wave models, and boulder transport equations to test the hypothesis that such boulders must have been emplaced by storms of greater-than-historical intensity. By contrast, our results suggest that with the higher relative sea level (RSL) estimated for the Bahamas during MIS 5e, boulders of this size could have been transported by waves generated by storms of historical intensity. Thus, while the megaboulders of Eleuthera cannot be used as geologic proof for past “superstorms,” they do show that with rising sea levels, cliffs and coastal barriers will be subject to significantly greater erosional energy, even without changes in storm intensity.

  20. Giant boulders and Last Interglacial storm intensity in the North Atlantic.

    Science.gov (United States)

    Rovere, Alessio; Casella, Elisa; Harris, Daniel L; Lorscheid, Thomas; Nandasena, Napayalage A K; Dyer, Blake; Sandstrom, Michael R; Stocchi, Paolo; D'Andrea, William J; Raymo, Maureen E

    2017-11-14

    As global climate warms and sea level rises, coastal areas will be subject to more frequent extreme flooding and hurricanes. Geologic evidence for extreme coastal storms during past warm periods has the potential to provide fundamental insights into their future intensity. Recent studies argue that during the Last Interglacial (MIS 5e, ∼128-116 ka) tropical and extratropical North Atlantic cyclones may have been more intense than at present, and may have produced waves larger than those observed historically. Such strong swells are inferred to have created a number of geologic features that can be observed today along the coastlines of Bermuda and the Bahamas. In this paper, we investigate the most iconic among these features: massive boulders atop a cliff in North Eleuthera, Bahamas. We combine geologic field surveys, wave models, and boulder transport equations to test the hypothesis that such boulders must have been emplaced by storms of greater-than-historical intensity. By contrast, our results suggest that with the higher relative sea level (RSL) estimated for the Bahamas during MIS 5e, boulders of this size could have been transported by waves generated by storms of historical intensity. Thus, while the megaboulders of Eleuthera cannot be used as geologic proof for past "superstorms," they do show that with rising sea levels, cliffs and coastal barriers will be subject to significantly greater erosional energy, even without changes in storm intensity.

  1. Marvelous Mud

    Science.gov (United States)

    Keeler, Rusty

    2011-01-01

    The author visited the Open Spaces Preschool in Whangarei, New Zealand and was surprised to see the most amazing natural preschool play. There were six preschoolers stripped down to tee shirts and underpants slipping, slopping, and sliding in the dirt spot which had now become the most lovely, silky-smooth deep-brown mud ever. Studies have…

  2. Mud Volcanoes as Exploration Targets on Mars

    Science.gov (United States)

    Allen, Carlton C.; Oehler, Dorothy Z.

    2010-01-01

    Tens of thousands of high-albedo mounds occur across the southern part of the Acidalia impact basin on Mars. These structures have geologic, physical, mineralogic, and morphologic characteristics consistent with an origin from a sedimentary process similar to terrestrial mud volcanism. The potential for mud volcanism in the Northern Plains of Mars has been recognized for some time, with candidate mud volcanoes reported from Utopia, Isidis, northern Borealis, Scandia, and the Chryse-Acidalia region. We have proposed that the profusion of mounds in Acidalia is a consequence of this basin's unique geologic setting as the depocenter for the tune fraction of sediments delivered by the outflow channels from the highlands.

  3. Ferroacryl mud for drilling deep bore holes

    Energy Technology Data Exchange (ETDEWEB)

    Lisyanskiy, V I; Chepiga, V I; Devydenko, V N

    1982-01-01

    The composition, technology of production and control of the parameters of a ferroacyl (FAR) mud for drilling for prospecting holes in the Donets-Basin are developed. The mud consists of Chasov Yal clay (150-160 kg), hypane (40 1), iron sulfate (1kg) and water (approximately 1 m/sup 3/). The mud exhibits the following parameters: density 1.05 -1.1 g/cm/sup 3/, viscosity 20-21 s; water yield 3-5 cm/sup 3/; crust 0.5 mm. Compared to existing flushing fluids based on hypane the FAR contains fewer components and the cost of the materials is considerably less. It features very high flocculating properties.

  4. A Bingham-plastic model for fluid mud transport under waves and currents

    Science.gov (United States)

    Liu, Chun-rong; Wu, Bo; Huhe, Ao-de

    2014-04-01

    Simplified equations of fluid mud motion, which is described as Bingham-Plastic model under waves and currents, are presented by order analysis. The simplified equations are non-linear ordinary differential equations which are solved by hybrid numerical-analytical technique. As the computational cost is very low, the effects of wave current parameters and fluid mud properties on the transportation velocity of the fluid mud are studied systematically. It is found that the fluid mud can move toward one direction even if the shear stress acting on the fluid mud bed is much smaller than the fluid mud yield stress under the condition of wave and current coexistence. Experiments of the fluid mud motion under current with fluctuation water surface are carried out. The fluid mud transportation velocity predicted by the presented mathematical model can roughly match that measured in experiments.

  5. Biota - 2011 Vegetation Inventory - Mud Lake, MN/SD

    Data.gov (United States)

    Army Corps of Engineers, Department of the Army, Department of Defense — 2011 Vegetation Classification for Mud Lake, MN/SD Vegetation Project Report, OMBIL Environmental Stewardship - Level 1 Inventory. Mud Lake, located on the Minnesota...

  6. A reagent for processing drilling muds

    Energy Technology Data Exchange (ETDEWEB)

    Polyakov, G.A.; Khon-Pak, A.T.; Khon, A.V.; Normatov, L.N.; Telegin, B.V.

    1983-01-01

    A reagent is proposed for processing drilling muds. It contains an acrylic polymer and potassium permanganate. The reagent is distinguished by the fact that in order to improve the quality of the drilling muds by increasing their salt resistance, the reagent contains hydrolized nitron fiber as the acrylic polymer with the following component relationship (in percent by weight): potassium permanganate, 0.015 to 0.065 and hydrolyzed nitron fiber, the remainder.

  7. Red mud as a carbon sink: variability, affecting factors and environmental significance.

    Science.gov (United States)

    Si, Chunhua; Ma, Yingqun; Lin, Chuxia

    2013-01-15

    The capacity of red mud to sequester CO(2) varied markedly due to differences in bauxite type, processing and disposal methods. Calcium carbonates were the dominant mineral phases responsible for the carbon sequestration in the investigated red mud types. The carbon sequestration capacity of red mud was not fully exploited due to shortages of soluble divalent cations for formation of stable carbonate minerals. Titanate and silicate ions were the two major oxyanions that appeared to strongly compete with carbonate ions for the available soluble Ca. Supply of additional soluble Ca and Mg could be a viable pathway for maximizing carbon sequestration in red mud and simultaneously reducing the causticity of red mud. It is roughly estimated that over 100 million tonnes of CO(2) have been unintentionally sequestered in red mud around the world to date through the natural weathering of historically produced red mud. Based on the current production rate of red mud, it is likely that some 6 million tonnes of CO(2) will be sequestered annually through atmospheric carbonation. If appropriate technologies are in place for incorporating binding cations into red mud, approximately 6 million tonnes of additional CO(2) can be captured and stored in the red mud while the hazardousness of red mud is simultaneously reduced. Copyright © 2012 Elsevier B.V. All rights reserved.

  8. Identification of mud crab reovirus VP12 and its interaction with the voltage-dependent anion-selective channel protein of mud crab Scylla paramamosain.

    Science.gov (United States)

    Xu, Hai-Dong; Su, Hong-Jun; Zou, Wei-Bin; Liu, Shan-Shan; Yan, Wen-Rui; Wang, Qian-Qian; Yuan, Li-Li; Chan, Siuming Francis; Yu, Xiao-Qiang; He, Jian-Guo; Weng, Shao-Ping

    2015-05-01

    Mud crab reovirus (MCRV) is the causative agent of a severe disease in cultured mud crab (Scylla paramamosain), which has caused huge economic losses in China. MCRV is a double-stranded RNA virus with 12 genomic segments. In this paper, SDS-PAGE, mass spectrometry and Western blot analyses revealed that the VP12 protein encoded by S12 gene is a structural protein of MCRV. Immune electron microscopy assay indicated that MCRV VP12 is a component of MCRV outer shell capsid. Yeast two hybrid cDNA library of mud crab was constructed and mud crab voltage-dependent anion-selective channel (mcVDAC) was obtained by MCRV VP12 screening. The full length of mcVDAC was 1180 bp with an open reading frame (ORF) of 849 bp encoding a 282 amino acid protein. The mcVDAC had a constitutive expression pattern in different tissues of mud crab. The interaction between MCRV VP12 and mcVDAC was determined by co-immunoprecipitation assay. The results of this study have provided an insight on the mechanisms of MCRV infection and the interactions between the virus and mud crab. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. Comparison of Copper Scavenging Capacity between Two Different Red Mud Types

    Directory of Open Access Journals (Sweden)

    Yingqun Ma

    2012-09-01

    Full Text Available A batch experiment was conducted to compare the Cu scavenging capacity between two different red mud types: the first one was a highly basic red mud derived from a combined sintering and Bayer process, and the second one was a seawater-neutralized red mud derived from the Bayer process. The first red mud contained substantial amounts of CaCO3, which, in combination with the high OH− activity, favored the immobilization of water-borne Cu through massive formation of atacamite. In comparison, the seawater-neutralized red mud had a lower pH and was dominated by boehmite, which was likely to play a significant role in Cu adsorption. Overall, it appears that Cu was more tightly retained by the CaCO3-dominated red mud than the boehmite-dominated red mud. It is concluded that the heterogeneity of red mud has marked influences on its capacity to immobilize water-borne Cu and maintain the long-term stability of the immobilized Cu species. The research findings obtained from this study have implications for the development of Cu immobilization technology by using appropriate waste materials generated from the aluminium industry.

  10. Comparison of Copper Scavenging Capacity between Two Different Red Mud Types

    Science.gov (United States)

    Ma, Yingqun; Si, Chunhua; Lin, Chuxia

    2012-01-01

    A batch experiment was conducted to compare the Cu scavenging capacity between two different red mud types: the first one was a highly basic red mud derived from a combined sintering and Bayer process, and the second one was a seawater-neutralized red mud derived from the Bayer process. The first red mud contained substantial amounts of CaCO3, which, in combination with the high OH− activity, favored the immobilization of water-borne Cu through massive formation of atacamite. In comparison, the seawater-neutralized red mud had a lower pH and was dominated by boehmite, which was likely to play a significant role in Cu adsorption. Overall, it appears that Cu was more tightly retained by the CaCO3-dominated red mud than the boehmite-dominated red mud. It is concluded that the heterogeneity of red mud has marked influences on its capacity to immobilize water-borne Cu and maintain the long-term stability of the immobilized Cu species. The research findings obtained from this study have implications for the development of Cu immobilization technology by using appropriate waste materials generated from the aluminium industry.

  11. Potential environmental benefits from regulatory consideration of synthetic drilling muds

    International Nuclear Information System (INIS)

    Burke, C.J.; Veil, J.A.

    1995-02-01

    When drilling exploration and production wells for oil and gas, drillers use specialized drilling fluids, referred to as muds, to help maintain well control and to remove drill cuttings from the hole. Historically, either water-based muds (WBMs) or oil-based muds (OBMs) have been used for offshore wells. Recently, in response to US Environmental Protection Agency (EPA) regulations and drilling-waste discharge requirements imposed by North Sea nations, the drilling industry has developed several types of synthetic-based muds (SBMs) that combine the desirable operating qualities of OBMs with the lower toxicity and environmental impact qualities of WBMs. This report describes the operational, environmental, and economic features of all three types of muds and discusses potential EPA regulatory barriers to wider use of SBMs

  12. Bioactive substances of the Techirghiol therapeutic mud

    Directory of Open Access Journals (Sweden)

    Mihail Hoteteu

    2018-02-01

    Full Text Available The study aims to characterize Techirghiol's sapropelic mud both by determining the organic and inorganic composition of the constituent phases and by isolating some compounds of humic substances. The distribution between the solid and liquid phases of the peloid of the Ca2+, Mg2+, Fe3+cations, PO43- anion, bioactive compounds of the protein, lipid and carbohydrate classes as well as the phosphatase activity of Techirghiol sapropelic mud are analyzed. The mud is fractionated using the pH and solvent polarity variation and is spectrophotometrically characterized based on absorption in the wavelength range 340-700 nm humic acids and fulvic acids differentiated on the basis of solubility and molecular mass.

  13. Irradiation of residual muds and its use in the oat cultivation

    International Nuclear Information System (INIS)

    Moreno, A.J.; Colin, C.A.; Gomeztagle, M.M.; Frias, P.H.

    1997-01-01

    The irradiation of residual muds samples from a wastewater treatment plant at gamma radiation dose of 15 kGy removes from muds on average: fats and oils (33%), detergent (92%), phenols (50%) and over 99% of microorganisms of total account. The evaluation of irradiated residual mud and without irradiation as soil conditioner in oat growing (avena safira), was realized by triplicate, using different rates (80, 60, 40 and 20%) of frank sandy soil and irradiated and non-irradiated residual mud. The growing with rates 60/40 % of soil and irradiated mud respectively, resulted being more adequate as soil conditioner. It is important to clarify that for putting residual mud it is necessary that metals concentration not exceed the maximum permissible levels for the soil type and the corresponding growing. (Author)

  14. Feasibility study for an innovative industrial red mud utilisation method.

    Science.gov (United States)

    Kounalakis, Petros; Aravossis, Konstantinos; Karayianni, ChS

    2016-02-01

    Red mud is a high volume industrial waste, and its management poses a unique challenge. For the utilisation of red mud, an economical, energy saving, environmental friendly and widely applicable method has been found. The proposed novel method is purely chemical, and achieves the recovery of all the oxides contained in red mud totally and transforms them into high value added products. The present work shows that an investment in an industrial plant, treating red mud and turning a toxic industrial waste in commercial products, is safe and viable. © The Author(s) 2015.

  15. Evaluation of Boulder, CO, SmartRegs Ordinance and Better Buildings Program

    Energy Technology Data Exchange (ETDEWEB)

    Arena, L.; Vijayakumar, G.

    2012-04-01

    Under the SmartRegs ordinance in the city of Boulder, Colorado, all rental properties in the city must achieve an energy efficiency level comparable to a HERS Index of approximately 120 points or lower by the year 2019. The City of Boulder received a $12 million grant from the DOE's Better Buildings initiative to create and incentivize their EnergySmart Program. In this report, the Consortium for Advanced Residential Buildings (CARB) describes its work with the program, including energy audits of rental properties, developing training programs for insulators and inspectors, and conducting interviews with property owners.

  16. Evaluation of Boulder, CO,SmartRegs Ordinance and Better Buildings Program

    Energy Technology Data Exchange (ETDEWEB)

    Arena, L. [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States); Vijayakumar, G. [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States)

    2012-04-01

    Under the SmartRegs ordinance in the city of Boulder, Colorado, all rental properties in the city must achieve an energy efficiency level comparable to a HERS Index of approximately 120 points or lower by the year 2019. The City of Boulder received a $12 million grant from the DOE’s Better Buildings initiative to create and incentivize their EnergySmart Program. In this report, the Consortium for Advanced Residential Buildings (CARB) describes its work with the program, including energy audits of rental properties, developing training programs for insulators and inspectors, and conducting interviews with property owners.

  17. Discrete Element Method Simulation of a Boulder Extraction From an Asteroid

    Science.gov (United States)

    Kulchitsky, Anton K.; Johnson, Jerome B.; Reeves, David M.; Wilkinson, Allen

    2014-01-01

    The force required to pull 7t and 40t polyhedral boulders from the surface of an asteroid is simulated using the discrete element method considering the effects of microgravity, regolith cohesion and boulder acceleration. The connection between particle surface energy and regolith cohesion is estimated by simulating a cohesion sample tearing test. An optimal constant acceleration is found where the peak net force from inertia and cohesion is a minimum. Peak pulling forces can be further reduced by using linear and quadratic acceleration functions with up to a 40% reduction in force for quadratic acceleration.

  18. Mud depocenters on continental shelves—appearance, initiation times, and growth dynamics

    Science.gov (United States)

    Hanebuth, Till J. J.; Lantzsch, Hendrik; Nizou, Jean

    2015-12-01

    Mud accumulates on continental shelves under a variety of environmental conditions and results in a diverse formation of mud depocenters (MDCs). Their three-dimensional architectures have been in the focus of several recent studies. Due to some terminological confusion concerning MDCs, the present study sets out to define eight individual MDC types in terms of surface sediment distribution and internal geometry. Under conditions of substantial sediment supply, prodeltas (distal zones off river deltas; triangular sheets), subaqueous deltas (disconnected from deltas by strong normal-to-shore currents; wedge-like clinoforms), and mud patches (scattered distribution) and mud blankets (widespread covers) are formed. Forced by hydrodynamic conditions, mud belts in the strict sense (detached from source; elongated bodies), and shallow-water contourite drifts (detached from source; growing normal to prevailing current direction; triangular clinoforms) develop. Controlled by local morphology, mud entrapments (in depressions, behind morphological steps) and mud wedges (triangular clinoforms growing in flow direction) are deposited. Shelf mud deposition took place (1) during early outer-shelf drowning (~14 ka), (2) after inner-shelf inundation to maximum flooding (9.5-6.5 ka), and (3) in sub-recent times (near the fluvial source, (2) uni-directional, extending along advective current transport paths, and (3) progradational, forming clinoforms that grow either parallel or normal to the bottom current direction. Classical mud belts may be initiated around defined nuclei, the remote sites of which are determined by seafloor morphology rather than the location of the source. From a stratigraphic perspective, mud depocenters coincide with sea-level highstand-related, shelf-wide condensed sections. They often show a conformable succession from transgressive to highstand systems tract stages.

  19. Mechanism of high-temperature resistant water-base mud

    Energy Technology Data Exchange (ETDEWEB)

    Luo, P

    1981-01-01

    Based on experiments, the causes and laws governing the changes in the performance of water-base mud under high temperature are analyzed, and the requisites and mechanism of treating agents resisting high temperature are discussed. Ways and means are sought for inhibiting, delaying and making use of the effect of high temperature on the performance of mud, while new ideas and systematic views have been expressed on the preparation of treating agents and set-up of a high temperature resistant water-base mud system. High temperature dispersion and high temperature surface inactivation of clay in the mud, as well as their effect and method of utilization are reviewed. Subjects also touched upon include degradation and cross-linking of the high-temperature resistant treating agents, their use and effect. Based on the above, the preparation of a water-base and system capable of resisting 180 to 250/sup 0/C is recommended.

  20. Heavy metals distribution in the Dead Sea black mud, Jordan

    International Nuclear Information System (INIS)

    Momani, K.; El-Hasan, T.; Auaydeh, S.

    2009-01-01

    The concentrations of trace metals (Fe, Mn, Ni, Zn, Co, Cr, Cu and Pb) were investigated in the Dead Sea black mud and river sediments in the northern basin of the Dead Sea region, Jordan. The pH of the mud was slightly above 8 while it was around 6 for the seawater. All analyzed heavy metal content in the black mud, except Pb, was less than their contents in other types of mud. Tlis might be due to the effect of the mildly acideic pH of seawater, which would enhance the metal solubility or incorporation within salt mineral structure, rather than precipitation. The sequential extraction results showed that Ni and Co transferred into the carbonate fraction, Mn is found mostly as manganese-iron oxide, and the residual phase contained Cr, Cu, Fe,and Pb. This study illustrated that the black mud had low heavy metal contents, thus indicating low toxicity. additionally, it shows insignificance effect of the mixing of freshwater with seawater on the heavy metal contents in the black mud. (authors).

  1. Mud Brick Resilience

    DEFF Research Database (Denmark)

    Johannessen, Runa

    2012-01-01

    In the seemingly endless circle of demolition and illegal rebuilding hand-made mud bricks produced from the soil of contested territory become an act of resistance. In June 2011, the Palestinian village Fasayel encountered the Israeli military’s demolition of 21 of the village’s built structures....

  2. Drilling mud

    Energy Technology Data Exchange (ETDEWEB)

    Babets, M A; Nechayev, N D; Vinogradova, G P

    1982-01-01

    A drilling mud is proposed which contains clay, alkali, water and stabilizer reagent. It is distinguished by the fact that in order to improve the viscosity and static shear stress, the stabilizer reagent contained is composted solid general wastes with the following ratio of components (% by weight): clay 10-15, alkali 0.1-0.2; composted solid general wastes 2-5; water--the rest.

  3. Magnetic Characterization of Sand and Boulder Samples from Citarum River and Their Origin

    Directory of Open Access Journals (Sweden)

    Sudarningsih

    2017-09-01

    Full Text Available The Citarum River is a nationally strategic river located near Bandung, the capital city of West Java Province. The feasibility of using magnetic methods for monitoring pollution level is currently being tested in the river. Due to its location in a volcanic area, the sediments from the river are expected to be highly magnetic. In this study, sand and boulder samples from Balekambang, a relatively pristine upstream area of the river, were subjected to magnetic and geochemical characterizations to establish the baseline for unpolluted sediments. Such baseline is important for future magnetic monitoring of sediments in the river. The mass-specific magnetic susceptibility of boulder samples was found to be varied from 819.2 to 2340.5 × 10-8m3 kg-1 while that of sand samples varied from 2293.9 to 3845.3 × 10-8m3 kg-1. These high magnetic susceptibility values infer that river sediments are highly magnetic even before being contaminated by industrial and household wastes. The predominant magnetic mineral in sand samples was multi-domain magnetite while that in boulder samples was single to pseudo-single domain magnetite. These differences were supported by the results from petrographic and XRF analyses, implying that the sand and boulder samples originated from different geological formations.

  4. Assessment of contamination by percolation of septic tank effluent through natural and amended soils.

    Science.gov (United States)

    Cheung, K C; Venkitachalam, T H

    2004-01-01

    Fly ash has been found to be a potential material for the treatment of municipal and industrial wastewater, and may be useful in the treatment of septic tank effluent. Laboratory columns (30 cm) were used to determine the sorption capacity and hydraulic properties of lagoon fly ash, loamy sand, sand, and sand amended by lagoon fly ash (30 and 60%) and red mud gypsum (20%). The removal of chemical oxygen demand (COD) was high in all column effluents (71-93%). Extent of nitrification was high in Spearwood sand, Merribrook loamy sand and 20% red mud gypsum amended Spearwood sand. However, actual removal of nitrogen (N) was high in columns containing lagoon fly ash. Unamended Spearwood sand possessed only minimal capacity for P sorption. Merribrook loamy sand and red mud gypsum amended sand affected complete P removal throughout the study period of 12 weeks. Significant P leakage occurred from lagoon fly ash amended sand columns following 6-10 weeks of operation. Neither lagoon fly ash nor red mud gypsum caused any studied heavy metal contamination including manganese (Mn), lead (Pb), zinc (Zn), cadmium (Cd) and chromium (Cr) of effluent. It can be concluded that Merribrook loamy sand is better natural soil than Spearwood sand as a filter medium. The addition of lagoon fly ash enhanced the removal of P in Spearwood sand but the efficiency was lower than with red mud gypsum amendment.

  5. Optimization of Mud Hammer Drilling Performance--A Program to Benchmark the Viability of Advanced Mud Hammer Drilling

    Energy Technology Data Exchange (ETDEWEB)

    Arnis Judzis

    2006-03-01

    Operators continue to look for ways to improve hard rock drilling performance through emerging technologies. A consortium of Department of Energy, operator and industry participants put together an effort to test and optimize mud driven fluid hammers as one emerging technology that has shown promise to increase penetration rates in hard rock. The thrust of this program has been to test and record the performance of fluid hammers in full scale test conditions including, hard formations at simulated depth, high density/high solids drilling muds, and realistic fluid power levels. This paper details the testing and results of testing two 7 3/4 inch diameter mud hammers with 8 1/2 inch hammer bits. A Novatek MHN5 and an SDS Digger FH185 mud hammer were tested with several bit types, with performance being compared to a conventional (IADC Code 537) tricone bit. These tools functionally operated in all of the simulated downhole environments. The performance was in the range of the baseline ticone or better at lower borehole pressures, but at higher borehole pressures the performance was in the lower range or below that of the baseline tricone bit. A new drilling mode was observed, while operating the MHN5 mud hammer. This mode was noticed as the weight on bit (WOB) was in transition from low to high applied load. During this new ''transition drilling mode'', performance was substantially improved and in some cases outperformed the tricone bit. Improvements were noted for the SDS tool while drilling with a more aggressive bit design. Future work includes the optimization of these or the next generation tools for operating in higher density and higher borehole pressure conditions and improving bit design and technology based on the knowledge gained from this test program.

  6. Integrated mined-area reclamation and land use planning. Volume 3A. A case study of surface mining and reclamation planning: South Boulder Creek Park Project, Sand and Gravel Operations, Boulder, Colorado

    Energy Technology Data Exchange (ETDEWEB)

    Lewis, L R; Perry, A O; LaFevers, J R

    1977-02-01

    This case study details reclamation planning for the Flatiron Companies' South Boulder Creek Park Project in Boulder, Colorado. The site contains a deposit of high-quality sand and gravel considered to be one of the best and largest known deposits of aggregate materials in the Front Range area. The aggregate deposit is located in a highly visible site just off the Denver-Boulder Turnpike at the entrance to the city from Denver, and adjacent to a residential portion of the city. In order to make maximum use of pre-mining planning, as a tool for resolving a conflict over the company's proposed operation, an extensive cooperative planning effort was initiated. This included the preparation of an environmental impact assessment, numerous public hearings, operating and reclamation plan review by city authorities, annexation of the site to the city, and the granting of a scenic easement on the property to the city for the development of a regional recreation park. A suite of contractual agreements was worked out among Flatiron Companies, the City of Boulder, the Colorado Open Lands Foundation, and the Federal Bureau of Outdoor Recreation. The purpose of this case study is to allow the planner to gain insight into the procedures, possibilities, and constraints involved in premining planning in a cooperative situation.

  7. Wadden Sea Mud

    DEFF Research Database (Denmark)

    Møller-Jensen, P.

    The present thesis deals with the transport phenomena of estuarine cohesive sediment from a laboratory and a numerical point of view. The cohesive sediment used throughout the whole process was natural mud from the Danish part of the Wadden sea, Ho Bay. In the laboratory, the work was concentrated...

  8. Treatment and use of muds of wastewaters in the agriculture

    International Nuclear Information System (INIS)

    Mendez A, Hernando

    1995-01-01

    The plant includes a preliminary treatment of the domestic residual waters; with two anaerobic reactors type UASB and a facultative lagoon as pos-treatment, system that reaches a removal of 85% of organic load, obtaining a tributary of 20 g/cm 3 of biodegradable oxygen. It is in the primary treatment where muds of interest are generated from the point of view of their application with agricultural and forest aims. These muds present a majors elements as P, Ca, K, Mg and minor, Fe, Cu, Zn being these nutrients and the organic matter the components that allow a good development of the material vegetable forest and agricultural type. In the agricultural area of CORPOICA and the CDMB jointly developed studies of laboratory greenhouse and of field with the purpose of knowing the potential of the muds like nutrition source. The greenhouse study, showed significant results of the muds on the development of the plants of corn and under field conditions the grain production increased from 1.051 kg/ha to 2;077 kg/ha with the treatments without muds and with three tons for hectare respectively. In another study on the pathogen population of muds handling, the behavior of the population of some pathogens organisms, of the blended muds was evaluated with agricultural lime, it diminished the population of fecal coliform bacteria, clastridium, mushrooms and yeasts significantly

  9. Usability of Clay Mixed Red Mud as Building Material in Transdanubian (Hungary) Region

    International Nuclear Information System (INIS)

    Sas, Z.; Somlai, J.J.; Szeiler, G.; Kovacs, T.

    2014-01-01

    The most commonly used building materials in Hungary and in numerous country of the world are the bricks, which made from clays. Due to the congenial internal structure properties of the clays these raw materials can be mixed with other materials, provides great possibility to reuse industrial by-products as additive material. The production and inbuilt of new types of synthetic building materials based on NORM (naturally occurring radioactive materials) by-products is raising concerns among authorities, public and scientists. Several NORM residues produced in large quantity, such as: phospogypsum (phosphate industry), red mud (aluminium processing industry), fly ash, coal slag (coal burning and steelworks) and so on are presently under investigation. The aluminum manufacturing in Ajka (Hungary) started in 1943. As a result of the bauxite refining activities up to now approximately 30 Mt of red mud has been produced in Hungary, stored in reservoirs. The radionuclide content of the bauxite usually exceeds the world average in soils (WA), which entirely remains in the by-product during Bayer process. The exposure pathways in case of application of NORM residues have to be explored in order to reveal the potential risks of NORMs on residents. The gamma radiation originated from the primordial radionuclides (K-40; U-238; Th-232) and their daughter elements found in nature and in building materials as well increase the external dose of the human body. In the EU the Radiation Protection 112 (RP 112) guideline serves for classification of building material, wherein the gamma exposure is limited by I-index

  10. Synthesis of petrographic, geochemical, and isotopic data for the Boulder batholith, southwest Montana

    Science.gov (United States)

    du Bray, Edward A.; Aleinikoff, John N.; Lund, Karen

    2012-01-01

    The Late Cretaceous Boulder batholith in southwest Montana consists of the Butte Granite and a group of associated smaller intrusions emplaced into Mesoproterozoic to Mesozoic sedimentary rocks and into the Late Cretaceous Elkhorn Mountains Volcanics. The Boulder batholith is dominated by the voluminous Butte Granite, which is surrounded by as many as a dozen individually named, peripheral intrusions. These granodiorite, monzogranite, and minor syenogranite intrusions contain varying abundances of plagioclase, alkali feldspar, quartz, biotite, hornblende, rare clinopyroxene, and opaque oxide minerals. Mafic, intermediate, and felsic subsets of the Boulder batholith intrusions are defined principally on the basis of color index. Most Boulder batholith plutons have inequigranular to seriate textures although several are porphyritic and some are granophyric (and locally miarolitic). Most of these plutons are medium grained but several of the more felsic and granophyric intrusions are fine grained. Petrographic characteristics, especially relative abundances of constituent minerals, are distinctive and foster reasonably unambiguous identification of individual intrusions. Seventeen samples from plutons of the Boulder batholith were dated by SHRIMP (Sensitive High Resolution Ion Microprobe) zircon U-Pb geochronology. Three samples of the Butte Granite show that this large pluton may be composite, having formed during two episodes of magmatism at about 76.7 ± 0.5 Ma (2 samples) and 74.7 ± 0.6 million years ago (Ma) (1 sample). However, petrographic and chemical data are inconsistent with the Butte Granite consisting of separate, compositionally distinct intrusions. Accordingly, solidification of magma represented by the Butte Granite appears to have spanned about 2 million year (m.y.). The remaining Boulder batholith plutons were emplaced during a 6-10 m.y. span (81.7 ± 1.4 Ma to 73.7 ± 0.6 Ma). The compositional characteristics of these plutons are similar to those

  11. What was the transport mode of large boulders in the Campine Plateau and the lower Meuse valley during the mid-Pleistocene?

    Science.gov (United States)

    De Brue, Hanne; Poesen, Jean; Notebaert, Bastiaan

    2015-01-01

    The Campine Plateau in northeastern Belgium, a remnant of an alluvial fan deposited by the Meuse River during the mid-Pleistocene, is characterised by the presence of boulders with maximum dimensions of up to 2 m, embedded in a gravel matrix. These boulders originated in the Ardennes region and are generally assumed to have been transported by ice-rafting processes. This paper investigates for the first time quantitatively the possibility of purely hydraulic transport of the boulders, taking into account channel and flow characteristics in the boulder provenance area during the mid-Pleistocene. Empirical transport relations that describe incipient motion thresholds in nonuniform river beds as a function of the relative grain size, or the ratio between the grain size of interest and the median grain size of the channel bed, are applied in order to calculate critical water depths for transport of boulders of various sizes. Results indicate that hydraulic transport of boulders with intermediate diameters < 1 m could have occurred within limited reaches of the palaeoriver, more specifically in the palaeo-Amblève tributary; whereas the small slope gradient of the palaeo-Meuse most probably inhibited boulder movement by hydraulic forces only. Although calculations of the ice volume required to lift a boulder to the water surface and comparison of the ice floe's dimensions with palaeochannel morphology do suggest that ice rafting is theoretically possible, several alternative, more probable transport mechanisms for the larger boulders of the Campine Plateau are proposed, requiring much smaller critical ice volumes and water depths than ice-rafting processes or purely hydraulic transport. These hypotheses include decreased bed friction and effective boulder density caused by a limited ice layer attached to the river bed and the boulder, hence lowering hydraulic transport thresholds, as well as the formation of ice jams and dams inducing catastrophic flooding and

  12. A modified time-temperature relationship for titanomagnetite and its application to igneous erratic boulders in Hachijo Island, Japan

    Science.gov (United States)

    Tonosaki, T.; Nakamura, N.; Goto, K.; Sato, T.; Watanabe, M.

    2016-12-01

    On land along shore line in an island all over the world, there are many huge boulders which seem that they had been broken and transported by errastic events (such as extreme waves). The presence of boulders on land provides geological evidence that the region had been suffered by ancient tsunami or storm waves, establishing the evaluation of risk-management policies for future disasters. In volcanic island of Hachijo, Japan, there are huge (>5000 kg) andesitic boulder (20 m altitude high), and basaltic boulders (4 m altitude high) which seem that they had been broken from an outcrop and emplaced from it. Because radiocarbon dating can not be applied to volcanic rocks, a magnetic viscous dating might be powerful tool to determine the rotation history of rocks. Tyson Smith and Vrosub (1994) succeeded in revealing the age of landslide basaltic rocks by geological evidence, using Pullaiah's time-temperature monogram by Neel's relaxation theory of single domain (SD) particles of magnetite (Pullaiah et al. 1975). However, our application of this monogram to igneous boulders fails to determine the age due to a different magnetic mineralogy including titanomagnetite. Therefore, by introducing a modified monogram for single domain particles of titanomagnetite, we tried to reveal a possible reworked age of the boulders. However, our boulders still fail to identify the reworked age. In this presentation, we will present our current situation of the problem and a working hypothesis to solve it.

  13. Pozzolanic Activity Assessment of LUSI (LUmpur SIdoarjo) Mud in Semi High Volume Pozzolanic Mortar

    Science.gov (United States)

    Hardjito, Djwantoro; Antoni; Wibowo, Gunadi M.; Christianto, Danny

    2012-01-01

    LUSI mud obtained from the mud volcano in Sidoarjo, Indonesia, is a viable aluminosilicate material to be utilized as pozzolanic material. LUSI is an abbreviation of the local name of the mud, i.e., Lumpur Sidoarjo, meaning Sidoarjo mud. This paper reports the results of an investigation to assess the pozzolanic activity of LUSI mud, especially in semi high volume pozzolanic mortar. In this case, the amount of mud incorporated is between 30% to 40% of total cementitious material, by mass. The content of SiO2 in the mud is about 30%, whilst the total content of SiO2, Fe2O3 and Al2O3 is more than 70%. Particle size and degree of partial cement replacement by treated LUSI mud affect the compressive strength, the strength activity index (SAI), the rate of pozzolanic activity development, and the workability of mortar incorporating LUSI mud. Manufacturing semi high volume LUSI mud mortar, up to at least 40% cement replacement, is a possibility, especially with a smaller particle size of LUSI mud, less than 63 μm. The use of a larger percentage of cement replacement by LUSI mud does not show any adverse effect on the water demand, as the flow of the fresh mortar increased with the increase of percentage of LUSI mud usage.

  14. Mud Volcanoes of Trinidad as Astrobiological Analogs for Martian Environments

    Directory of Open Access Journals (Sweden)

    Riad Hosein

    2014-10-01

    Full Text Available Eleven onshore mud volcanoes in the southern region of Trinidad have been studied as analog habitats for possible microbial life on Mars. The profiles of the 11 mud volcanoes are presented in terms of their physical, chemical, mineralogical, and soil properties. The mud volcanoes sampled all emitted methane gas consistently at 3% volume. The average pH for the mud volcanic soil was 7.98. The average Cation Exchange Capacity (CEC was found to be 2.16 kg/mol, and the average Percentage Water Content was 34.5%. Samples from three of the volcanoes, (i Digity; (ii Piparo and (iii Devil’s Woodyard were used to culture bacterial colonies under anaerobic conditions indicating possible presence of methanogenic microorganisms. The Trinidad mud volcanoes can serve as analogs for the Martian environment due to similar geological features found extensively on Mars in Acidalia Planitia and the Arabia Terra region.

  15. Mud Volcanoes of Trinidad as Astrobiological Analogs for Martian Environments

    Science.gov (United States)

    Hosein, Riad; Haque, Shirin; Beckles, Denise M.

    2014-01-01

    Eleven onshore mud volcanoes in the southern region of Trinidad have been studied as analog habitats for possible microbial life on Mars. The profiles of the 11 mud volcanoes are presented in terms of their physical, chemical, mineralogical, and soil properties. The mud volcanoes sampled all emitted methane gas consistently at 3% volume. The average pH for the mud volcanic soil was 7.98. The average Cation Exchange Capacity (CEC) was found to be 2.16 kg/mol, and the average Percentage Water Content was 34.5%. Samples from three of the volcanoes, (i) Digity; (ii) Piparo and (iii) Devil’s Woodyard were used to culture bacterial colonies under anaerobic conditions indicating possible presence of methanogenic microorganisms. The Trinidad mud volcanoes can serve as analogs for the Martian environment due to similar geological features found extensively on Mars in Acidalia Planitia and the Arabia Terra region. PMID:25370529

  16. Use of red mud as addition for portland cement mortars

    International Nuclear Information System (INIS)

    Ribeiro, D.V.; Morelli, M.R.

    2011-01-01

    The aim of the present research work was to investigate the possibility of adding red mud, an alkaline leaching waste that is obtained from bauxite during the Bayer process for alumina production, in the raw meal of Portland cement mortars. The red mud is classified as dangerous, according to NBR 10004/2004, and world while generation reached over 117 million tons/year. This huge production requires high consuming products to be used as incorporation matrix and we studied the influence of red mud addition on the characteristics of cement mortars and concrete. In this paper the properties of Portland cement mortars incorporating high amounts of red mud was evaluated: pH variation, fresh (setting time, workability or normal consistency and water retention), and hardened state (mechanical strength, capillary water absorption, density and apparent porosity). Results seem promising for red mud additions up to 20 wt%. (author)

  17. Mud volcanoes of trinidad as astrobiological analogs for martian environments.

    Science.gov (United States)

    Hosein, Riad; Haque, Shirin; Beckles, Denise M

    2014-10-13

    Eleven onshore mud volcanoes in the southern region of Trinidad have been studied as analog habitats for possible microbial life on Mars. The profiles of the 11 mud volcanoes are presented in terms of their physical, chemical, mineralogical, and soil properties. The mud volcanoes sampled all emitted methane gas consistently at 3% volume. The average pH for the mud volcanic soil was 7.98. The average Cation Exchange Capacity (CEC) was found to be 2.16 kg/mol, and the average Percentage Water Content was 34.5%. Samples from three of the volcanoes, (i) Digity; (ii) Piparo and (iii) Devil's Woodyard were used to culture bacterial colonies under anaerobic conditions indicating possible presence of methanogenic microorganisms. The Trinidad mud volcanoes can serve as analogs for the Martian environment due to similar geological features found extensively on Mars in Acidalia Planitia and the Arabia Terra region.

  18. Resources Management Strategy For Mud Crabs (Scylla spp.) In Pemalang Regency

    Science.gov (United States)

    Purnama Fitri, Aristi Dian; Boesono, Herry; Sabdono, Agus; Adlina, Nadia

    2017-02-01

    The aim of this research is to develop resources management strategies of mud crab (Scylla spp.) in Pemalang Regency. The method used is descriptive survey in a case study. This research used primary data and secondary data. Primary data were collected through field observations and in-depth interviews with key stakeholders. Secondary data were collected from related publications and documents issued by the competent institutions. SWOT Analysis was used to inventory the strengths, weaknesses, opportunities and threats. TOWS matrix was used to develop an alternative of resources management strategies. SWOT analysis was obtained by 6 alternative strategies that can be applied for optimization of fisheries development in Pemalang Regency. The strategies is the control of mud crab fishing gear, restricted size allowable in mud crab, control of mud crab fishing season, catch monitoring of mud crab, needs a management institutions which ensure the implementation of the regulation, and implementation for mud crab aquaculture. Each alternative strategy can be synergized to optimize the resources development in Pemalang Regency.

  19. Eruption of a deep-sea mud volcano triggers rapid sediment movement

    Science.gov (United States)

    Feseker, Tomas; Boetius, Antje; Wenzhöfer, Frank; Blandin, Jerome; Olu, Karine; Yoerger, Dana R.; Camilli, Richard; German, Christopher R.; de Beer, Dirk

    2014-01-01

    Submarine mud volcanoes are important sources of methane to the water column. However, the temporal variability of their mud and methane emissions is unknown. Methane emissions were previously proposed to result from a dynamic equilibrium between upward migration and consumption at the seabed by methane-consuming microbes. Here we show non-steady-state situations of vigorous mud movement that are revealed through variations in fluid flow, seabed temperature and seafloor bathymetry. Time series data for pressure, temperature, pH and seafloor photography were collected over 431 days using a benthic observatory at the active Håkon Mosby Mud Volcano. We documented 25 pulses of hot subsurface fluids, accompanied by eruptions that changed the landscape of the mud volcano. Four major events triggered rapid sediment uplift of more than a metre in height, substantial lateral flow of muds at average velocities of 0.4 m per day, and significant emissions of methane and CO2 from the seafloor. PMID:25384354

  20. Multi-hole seismic modeling in 3-D space and cross-hole seismic tomography analysis for boulder detection

    Science.gov (United States)

    Cheng, Fei; Liu, Jiangping; Wang, Jing; Zong, Yuquan; Yu, Mingyu

    2016-11-01

    A boulder stone, a common geological feature in south China, is referred to the remnant of a granite body which has been unevenly weathered. Undetected boulders could adversely impact the schedule and safety of subway construction when using tunnel boring machine (TBM) method. Therefore, boulder detection has always been a key issue demanded to be solved before the construction. Nowadays, cross-hole seismic tomography is a high resolution technique capable of boulder detection, however, the method can only solve for velocity in a 2-D slice between two wells, and the size and central position of the boulder are generally difficult to be accurately obtained. In this paper, the authors conduct a multi-hole wave field simulation and characteristic analysis of a boulder model based on the 3-D elastic wave staggered-grid finite difference theory, and also a 2-D imaging analysis based on first arrival travel time. The results indicate that (1) full wave field records could be obtained from multi-hole seismic wave simulations. Simulation results describe that the seismic wave propagation pattern in cross-hole high-velocity spherical geological bodies is more detailed and can serve as a basis for the wave field analysis. (2) When a cross-hole seismic section cuts through the boulder, the proposed method provides satisfactory cross-hole tomography results; however, when the section is closely positioned to the boulder, such high-velocity object in the 3-D space would impact on the surrounding wave field. The received diffracted wave interferes with the primary wave and in consequence the picked first arrival travel time is not derived from the profile, which results in a false appearance of high-velocity geology features. Finally, the results of 2-D analysis in 3-D modeling space are comparatively analyzed with the physical model test vis-a-vis the effect of high velocity body on the seismic tomographic measurements.

  1. Laboratory exposures of invertebrate and vertebrate species to concentrations of IA-35 (Petro-Canada) drill mud fluid, production water, and Hibernia mud cuttings

    Energy Technology Data Exchange (ETDEWEB)

    Payne, J.; Fancey, L.; Andrews, C.; Meade, J.; Power, F.; Veinot, G. [Department of Fisheries and Oceans, St. John' s, NF (Canada). Science Branch; Lee, K. [Department of Fisheries and Oceans, Mont-Joli, PQ (Canada). Maurice Lamontagne Inst.; Cook, A. [Environment Canada, Moncton, NB (Canada). Environmental Quality Laboratory

    2001-04-01

    The authors studied the short term effects on brine shrimp nauplii (Artemia franciscana), capelin larvae (Mallotus villosus), marine copepods (Calanus finmarchicus), juvenile yellowtail flounder (Limanda ferruginea) and ctenophores (Pleurobrachius pileus) of synthetic drill mud fluid, produced water and drill mud cuttings. In this report, they presented the data collected, including data on the water solubility of Petro-Canada drill mud fluid IA-35 and metal analysis of production water from the Sable Island Offshore Exploration Project. Low acute toxicity potential for drill mud fluid, production water and Hibernia drill cuttings for the species and life stages tested were revealed. The hypothesis to the effect that wastes pose very little or no risk of an acute toxic nature to the marine environment were reinforced by the results from this study. 5 refs., 25 tabs.

  2. City of Boulder, Colorado Municipal Tree Resource Analysis

    Science.gov (United States)

    E.G. McPherson; J.R. Simpson; P.J. Peper; S.L. Gardner; K.E. Vargas; Q. Xiao

    2005-01-01

    Boulder is a vibrant city, renowned for its livability and cultural wealth and well known for its Smart Growth policies that protect and restore environmental quality while enhancing economic opportunity. The city maintains trees as an integral component of the urban infrastructure. Research indicates that healthy trees can mitigate impacts associated with the built...

  3. Linking geochemical processes in mud volcanoes with arsenic mobilization driven by organic matter

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Chia-Chuan; Kar, Sandeep [Department of Earth Sciences, National Cheng Kung University, Tainan, Taiwan (China); Jean, Jiin-Shuh, E-mail: jiinshuh@mail.ncku.edu.tw [Department of Earth Sciences, National Cheng Kung University, Tainan, Taiwan (China); Wang, Chung-Ho [Institute of Earth Sciences, Academia Sinica, Taipei, Taiwan (China); Lee, Yao-Chang [National Synchrotron Radiation Research Center, Hsinchu 30076, Taiwan (China); Sracek, Ondra [OPV s.r.o. (Groundwater Protection Ltd.), Bělohorská 31, 169 00 Praha 6 (Czech Republic); Department of Geology, Faculty of Science, Palacký University, 17. listopadu 12, 771 46 Olomouc (Czech Republic); Li, Zhaohui [Department of Earth Sciences, National Cheng Kung University, Tainan, Taiwan (China); Department of Geosciences, University of Wisconsin – Parkside, Kenosha, WI 53144 (United States); Bundschuh, Jochen [Department of Earth Sciences, National Cheng Kung University, Tainan, Taiwan (China); Faculty of Engineering and Surveying and National Centre for Engineering in Agriculture, The University of Southern Queensland, Toowoomba (Australia); Yang, Huai-Jen [Department of Earth Sciences, National Cheng Kung University, Tainan, Taiwan (China); Chen, Chien-Yen [Department of Earth and Environmental Sciences, National Chung Cheng University, Chiayi 621, Taiwan (China)

    2013-11-15

    Highlights: ► Study represents geochemical characteristics and their spatial variability among six mud volcanoes of southern Taiwan. ► Anoxic mud volcanic fluids containing high NaCl imply connate water as the possible source. ► δ{sup 18}O-rich fluids is associated with silicate and carbonate mineral released through water–rock interaction. ► High As content in mud and its sequential extraction showed mostly adsorbed As on organic and sulphidic phases. ► Organic matter specially humic acid showed redox dependence and it may play an important role in binding and mobility of arsenic. -- Abstract: The present study deals with geochemical characterization of mud fluids and sediments collected from Kunshuiping (KSP), Liyushan (LYS), Wushanting (WST), Sinyangnyuhu (SYNH), Hsiaokunshui (HKS) and Yenshuikeng (YSK) mud volcanoes in southwestern Taiwan. Chemical constituents (cations, anions, trace elements, organic carbon, humic acid, and stable isotopes) in both fluids and mud were analyzed to investigate the geochemical processes and spatial variability among the mud volcanoes under consideration. Analytical results suggested that the anoxic mud volcanic fluids are highly saline, implying connate water as the probable source. The isotopic signature indicated that δ{sup 18}O-rich fluids may be associated with silicate and carbonate mineral released through water–rock interaction, along with dehydration of clay minerals. Considerable amounts of arsenic in mud irrespective of fluid composition suggested possible release through biogeochemical processes in the subsurface environment. Sequential extraction of As from the mud indicated that As was mostly present in organic and sulphidic phases, and adsorbed on amorphous Mn oxyhydroxides. Volcanic mud and fluids are rich in organic matter (in terms of organic carbon), and the presence of humic acid in mud has implications for the binding of arsenic. Functional groups of humic acid also showed variable sources of

  4. Linking geochemical processes in mud volcanoes with arsenic mobilization driven by organic matter.

    Science.gov (United States)

    Liu, Chia-Chuan; Kar, Sandeep; Jean, Jiin-Shuh; Wang, Chung-Ho; Lee, Yao-Chang; Sracek, Ondra; Li, Zhaohui; Bundschuh, Jochen; Yang, Huai-Jen; Chen, Chien-Yen

    2013-11-15

    The present study deals with geochemical characterization of mud fluids and sediments collected from Kunshuiping (KSP), Liyushan (LYS), Wushanting (WST), Sinyangnyuhu (SYNH), Hsiaokunshui (HKS) and Yenshuikeng (YSK) mud volcanoes in southwestern Taiwan. Chemical constituents (cations, anions, trace elements, organic carbon, humic acid, and stable isotopes) in both fluids and mud were analyzed to investigate the geochemical processes and spatial variability among the mud volcanoes under consideration. Analytical results suggested that the anoxic mud volcanic fluids are highly saline, implying connate water as the probable source. The isotopic signature indicated that δ(18)O-rich fluids may be associated with silicate and carbonate mineral released through water-rock interaction, along with dehydration of clay minerals. Considerable amounts of arsenic in mud irrespective of fluid composition suggested possible release through biogeochemical processes in the subsurface environment. Sequential extraction of As from the mud indicated that As was mostly present in organic and sulphidic phases, and adsorbed on amorphous Mn oxyhydroxides. Volcanic mud and fluids are rich in organic matter (in terms of organic carbon), and the presence of humic acid in mud has implications for the binding of arsenic. Functional groups of humic acid also showed variable sources of organic matter among the mud volcanoes being examined. Because arsenate concentration in the mud fluids was found to be independent from geochemical factors, it was considered that organic matter may induce arsenic mobilization through an adsorption/desorption mechanism with humic substances under reducing conditions. Organic matter therefore plays a significant role in the mobility of arsenic in mud volcanoes. Copyright © 2012 Elsevier B.V. All rights reserved.

  5. Structuring Disaster Recovery Infrastructure Decisions: Lessons from Boulder County's 2013 Flood Recovery

    Science.gov (United States)

    Clavin, C.; Petropoulos, Z.

    2017-12-01

    Recovery phase decision making processes, as compared to mitigation and response phase decision making processes, require communities make significant financial and capital decisions in the months after a disaster. Collectively, these investments may significantly contribute to the resilience of a community to future hazards. Pre-disaster administrative decisions are well-established within existing planning processes. Post-event recovery requires community decision makers to quickly evaluate technical proposals and manage significant recovery financial resources to ensure their community rebuilds in a manner that will be more resilient to future events. These technical and administrative hurdles in the aftermath of a disaster create a challenging atmosphere to make sound, scientifically-informed decisions leading to resilient recovery. In September 2013, a 1,000-year rain event that resulted in flooding throughout the Front Range of Colorado, significantly impacting Boulder County. While the event is long past, disaster recovery efforts still continue in parts of Boulder County. Boulder County officials formed a county collaborative that adapted the NIST Community Resilience Planning Guide for Buildings and Infrastructure Systems to facilitate a goals-based multi-criteria decision making process. Rather than use hazard-based information to guide infrastructure design, the county's decision process established time-to-recovery goals for infrastructure systems that were used as criteria for project design. This presentation explores the decision-making process employed by Boulder County to specify design standards for resilient rebuilding of infrastructure systems and examine how this infrastructure planning model could be extrapolated to other situations where there is uncertainty regarding future infrastructure design standards.

  6. Protecting black ash from the emerald ash borer

    Science.gov (United States)

    Les Benedict

    2010-01-01

    Black ash (Fraxinus nigra) is an important resource for Tribes in the Northeast and Great Lakes regions of the North American continent. Ash in North America is being threatened with widespread destruction as a result of the introduction of emerald ash borer beetle (Agrilus planipennis) in 2002. Measures are being taken to slow the spread of emerald ash borer beetle....

  7. Comparison with Offshore and Onshore Mud Volcanoes in the Southwestern Taiwan

    Science.gov (United States)

    Chen, Y. H.; Su, C. C.; Chen, T. T.; Liu, C. S.; Paull, C. K.; Caress, D. W.; Gwiazda, R.; Lundsten, E. M.; Hsu, H. H.

    2017-12-01

    The offshore area southwest (SW) of Taiwan is on the convergent boundary between the Eurasian and Philippine Sea plates. The plate convergence manifests in this unique geological setting as a fold-and-thrust-belt. Multi-channel seismic profiles, and bathymetry and gravity anomaly data collected from Taiwan offshore to the SW show the presence of a large amount of mud volcanoes and diapirs with NE-SW orientations. In the absence of comprehensive sampling and detailed geochemistry data from submarine mud volcanoes, the relation between onshore and offshore mud volcanoes remains ambiguous. During two MBARI and IONTU joint cruises conducted in 2017 we collected high-resolution multibeam bathymetry data (1-m-resolution) and chirp sub-bottom profiles with an autonomous underwater vehicle (AUV) from submarine Mud Volcano III (MV3), and obtained precisely located samples and video observations with a remotely operated vehicle (ROV). MV3 is an active submarine mud volcano at 465 m water depth offshore SW Taiwan. This cone-shape mud volcano is almost 780 m wide, 150 m high, with 8° slopes, and a 30 m wide mound on the top. Several linear features are observed in the southwest of the mound, and these features are interpreted as a series of marks caused by rolling rocks that erupted from the top of MV3. We collected three rocks and push cores from MV3 and its top with the ROV, in order to compare their chemical and mineralogical composition to that of samples collected from mud volcanoes along the Chishan fault. The surface and X-radiography imaging, 210Pb chronology, grain size and X-ray diffractometer analyses were conducted to compare geochemical and sedimentary properties of offshore and onshore mud volcanoes. The results indicate that the offshore and onshore mud volcanoes have similar characteristics. We suggest that offshore and onshore mud volcanoes of SW Taiwan are no different in the source of their materials and their mechanism of creation and evolution.

  8. A geochemical study on mud volcanoes in the Junggar Basin, China

    Energy Technology Data Exchange (ETDEWEB)

    Nakada, Ryoichi, E-mail: ryo-nakada@hiroshima-u.ac.jp [Department of Earth and Planetary Systems Science, Graduate School of Science, Hiroshima University, Higashi-Hiroshima, Hiroshima 739-8526 (Japan); Takahashi, Yoshio [Department of Earth and Planetary Systems Science, Graduate School of Science, Hiroshima University, Higashi-Hiroshima, Hiroshima 739-8526 (Japan); Tsunogai, Urumu [Division of Earth and Planetary Sciences, Graduate School of Science, Hokkaido University, Kita-10 Nishi-8, Kita-ku, Sapporo 060-0810 (Japan); Zheng Guodong [Key Laboratory of Petroleum Resources Research, Institute of Geology and Geophysics, Chinese Academy of Sciences, 382 West Donggang Road, Lanzhou 730000 (China); Shimizu, Hiroshi [Department of Earth and Planetary Systems Science, Graduate School of Science, Hiroshima University, Higashi-Hiroshima, Hiroshima 739-8526 (Japan); Hattori, Keiko H. [Department of Earth Science, University of Ottawa, Ottawa, ON, K1N 6N5 (Canada)

    2011-07-15

    Highlights: > Gases released from Xinjiang mud volcanoes are dominated by thermogenic origin. > Secondary microbial activities occurring closer to the surface dramatically changed the {delta}{sup 13}C{sub CO2}. > The water-rock interaction occurred at deeper level than gas and petroleum reservoir. - Abstract: A comprehensive study was performed to characterize, for the first time, the mud, water, and gases released from onshore mud volcanoes located in the southern margin of the Junggar Basin, northwestern China. Chemical compositions of mud, along with the geology of the basin, suggest that a source of the mud is Mesozoic or Cenozoic shale. Oxygen and H isotope compositions of the released water suggest a local meteoric origin. Combined with the positive Eu anomalies of the water, a large {sup 18}O shift of the water suggests extensive interaction with rocks. Gases discharged from the mud volcanoes are predominantly thermogenic hydrocarbons, and the high {delta}{sup 13}C values (>+20 per mille VPDB) for CO{sub 2} gases and dissolved carbonate in muddy water suggest secondary methanogenesis with CO{sub 2} reduction after oil biodegradation. The enrichments of Eu and {sup 18}O in water and the low thermal gradient of the area suggest that the water-rock interactions possibly occur deeper than 3670 {+-} 200 m. On the other hand, considering the relationship to the petroleum reservoir around the mud volcanoes, the depth of the gases can be derived from about 3600 m, a depth that is greater than that generally estimated for reservoirs whose gas is characterized by {sup 13}C-enriched CO{sub 2}. Oil biodegradation with CO{sub 2} reduction likely occurs at a shallower depth along the seepage system of the mud volcano. The results contribute to the worldwide data set of gas genesis in mud volcanoes. Moreover, they further support the concept that most terrestrial mud volcanoes release thermogenic gas produced in very deep sediments and may be early indicators of oil

  9. Characterization of ancient construction materials (mud walls and adobe in the churches at Cisneros, Villada and Boada de Campos (Palencia

    Directory of Open Access Journals (Sweden)

    Sánchez Hernández, R.

    2000-03-01

    Full Text Available The aim of this work is to characterize the ancient building materials (mud wall and adobe of three churches in the province of Palencia. This is the first part of a study which seeks to evaluate how the mud walls of the tower of the church of Cisneros reacted to restoration treatment which consisted of a structural reinforcement made by injecting a highly fluid grout of cement/lime/sand mortar. This treatment implies the introduction of large quantities of water into the fabric. The mud walls of the tower of Cisneros are compositionally and texturally very similar to each other, which indicates that despite their large dimensions, care was taken in the homogeneity of the materials. These mud walls are also very similar to those of the church of Villada. The original raw material is mud with some additives (rubble, ashes, bones, etc. and some remains of lime used as a stabiliser. Although there is a very high proportion of clay, no effervescing clay has been detected. Hence it is deduced that once the mud wall was built, there were no important changes in volume due to variation in the humidity of the fabric. The characteristics of the adobe of the tower of Boada are logically different form those of the mud walls, being made of less sandy, more clayey mud with a high proportion of straw that the mud walls do not have, and without the addition of bricks, bones, etc.

    El objetivo de este trabajo es caracterizar los materiales antiguos de construcción (tapial y adobe de tres iglesias en la provincia de Falencia. El trabajo es la primera parte de un estudio en el que se pretende evaluar el comportamiento de los tapiales de la torre de la iglesia de Cisneros frente al tratamiento de restauración, consistente en un cosido estructural mediante la realización de perforaciones en las que se introduce una barra de acero y donde, posteriormente, se inyecta una lechada muy fluidificada de mortero de cemento/cal/arena. Este tratamiento implica la

  10. OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE - A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING

    Energy Technology Data Exchange (ETDEWEB)

    Arnis Judzis

    2003-01-01

    This document details the progress to date on the ''OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE -- A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING'' contract for the quarter starting October 2002 through December 2002. Even though we are awaiting the optimization portion of the testing program, accomplishments included the following: (1) Smith International participated in the DOE Mud Hammer program through full scale benchmarking testing during the week of 4 November 2003. (2) TerraTek acknowledges Smith International, BP America, PDVSA, and ConocoPhillips for cost-sharing the Smith benchmarking tests allowing extension of the contract to add to the benchmarking testing program. (3) Following the benchmark testing of the Smith International hammer, representatives from DOE/NETL, TerraTek, Smith International and PDVSA met at TerraTek in Salt Lake City to review observations, performance and views on the optimization step for 2003. (4) The December 2002 issue of Journal of Petroleum Technology (Society of Petroleum Engineers) highlighted the DOE fluid hammer testing program and reviewed last years paper on the benchmark performance of the SDS Digger and Novatek hammers. (5) TerraTek's Sid Green presented a technical review for DOE/NETL personnel in Morgantown on ''Impact Rock Breakage'' and its importance on improving fluid hammer performance. Much discussion has taken place on the issues surrounding mud hammer performance at depth conditions.

  11. Advanced Mud System for Microhole Coiled Tubing Drilling

    Energy Technology Data Exchange (ETDEWEB)

    Kenneth Oglesby

    2008-12-01

    An advanced mud system was designed and key components were built that augment a coiled tubing drilling (CTD) rig that is designed specifically to drill microholes (less than 4-inch diameter) with advanced drilling techniques. The mud system was tailored to the hydraulics of the hole geometries and rig characteristics required for microholes and is capable of mixing and circulating mud and removing solids while being self contained and having zero discharge capability. Key components of this system are two modified triplex mud pumps (High Pressure Slurry Pumps) for advanced Abrasive Slurry Jetting (ASJ) and a modified Gas-Liquid-Solid (GLS) Separator for well control, flow return and initial processing. The system developed also includes an additional component of an advanced version of ASJ which allows cutting through most all materials encountered in oil and gas wells including steel, cement, and all rock types. It includes new fluids and new ASJ nozzles. The jetting mechanism does not require rotation of the bottom hole assembly or drill string, which is essential for use with Coiled Tubing (CT). It also has low reactive forces acting on the CT and generates cuttings small enough to be easily cleaned from the well bore, which is important in horizontal drilling. These cutting and mud processing components and capabilities compliment the concepts put forth by DOE for microhole coiled tubing drilling (MHTCTD) and should help insure the reality of drilling small diameter holes quickly and inexpensively with a minimal environmental footprint and that is efficient, compact and portable. Other components (site liners, sump and transfer pumps, stacked shakers, filter membranes, etc.. ) of the overall mud system were identified as readily available in industry and will not be purchased until we are ready to drill a specific well.

  12. Red mud flocculation process in alumina production

    Science.gov (United States)

    Fedorova, E. R.; Firsov, A. Yu

    2018-05-01

    The process of thickening and washing red mud is a gooseneck of alumina production. The existing automated systems of the thickening process control involve stabilizing the parameters of the primary technological circuits of the thickener. The actual direction of scientific research is the creation and improvement of models and systems of the thickening process control by model. But the known models do not fully consider the presence of perturbing effects, in particular the particle size distribution in the feed process, distribution of floccules by size after the aggregation process in the feed barrel. The article is devoted to the basic concepts and terms used in writing the population balance algorithm. The population balance model is implemented in the MatLab environment. The result of the simulation is the particle size distribution after the flocculation process. This model allows one to foreseen the distribution range of floccules after the process of aggregation of red mud in the feed barrel. The mud of Jamaican bauxite was acting as an industrial sample of red mud; Cytec Industries of HX-3000 series with a concentration of 0.5% was acting as a flocculant. When simulating, model constants obtained in a tubular tank in the laboratories of CSIRO (Australia) were used.

  13. The affirmation of the scientist-practitioner. A look back at Boulder.

    Science.gov (United States)

    Baker, D B; Benjamin, L T

    2000-02-01

    In the aftermath of World War II, several influences were paramount in forcing academic psychology to recognize, albeit reluctantly, the coming professionalization of psychology. The federal government, wishing to avoid a repeat of blunders following World War I that led to significant dissatisfaction among veterans, took proactive steps to ensure that mental health needs of the new veterans would be met. The USPHS and the VA were mandated to expand significantly the pool of mental health practitioners, a direction that led not only to the funding of the Boulder conference but also to the development of APA's accreditation program, funded practical and internship arrangements with the VA, and the USPHS grants to academic departments for clinical training. The GI Bill, amended to include payment for graduate education, created tremendous interest in graduate programs in psychology. As a result, psychology programs were inundated with funded applicants, most of whom were interested in the application of psychology to clinical and other applied fields. Graduate psychology departments were mixed in their views of this "blessing." The reality of a separate curriculum for professional training in psychology was a bitter pill for some academic psychologists to swallow. Graduate departments feared that control of their programs would be taken over by external forces and that they would lose their right to determine their own curriculum. Further, they feared the domination of clinical training within their own departments and the effects of such educational emphasis on their traditional experimental programs. The Boulder conference brought together these disparate needs and concerns, although one can argue about how well some points of view were represented with respect to others. It was a time of high anticipation and fear. The conference could easily have ended in failure, with such diverse interests being unable to reach any consensus. There are many letters in the

  14. Recent shallow moonquake and impact-triggered boulder falls on the Moon: New insights from the Schrödinger basin

    Science.gov (United States)

    Senthil Kumar, P.; Sruthi, U.; Krishna, N.; Lakshmi, K. J. P.; Menon, Rajeev; Amitabh; Gopala Krishna, B.; Kring, David A.; Head, James W.; Goswami, J. N.; Kiran Kumar, A. S.

    2016-02-01

    Shallow moonquakes are thought to be of tectonic origin. However, the geologic structures responsible for these moonquakes are unknown. Here we report sites where moonquakes possibly occurred along young lobate scarps in the Schrödinger basin. Our analysis of Lunar Reconnaissance Orbiter and Chandrayaan-1 images revealed four lobate scarps in different parts of the Schrödinger basin. The scarps crosscut small fresh impact craters (bounced on nearby slopes. A cluster of a large number of boulder falls near Scarp 1 indicates that the scarp was seismically active recently. A low runout efficiency of the boulders (~2.5) indicates low to moderate levels of ground shaking, which we interpret to be related to low-magnitude moonquakes in the scarp. Boulder falls are also observed in other parts of the basin, where we mapped >1500 boulders associated with trails and bouncing marks. Their origins are largely controlled by recent impact events. Ejecta rays and secondary crater chains from a 14 km diameter impact crater traversed Schrödinger and triggered significant boulder falls about 17 Ma. Therefore, a combination of recent shallow moonquakes and impact events triggered the boulder falls in the Schrödinger basin.

  15. Effect of potassium-salt muds on gamma ray, and spontaneous potential measurements

    International Nuclear Information System (INIS)

    Cox, J.W.; Raymer, L.L.

    1976-01-01

    Interpretations of the gamma ray and Spontaneous Potential curves generally assume the presence of sodium chloride as the dominant salt in both the formation water and the mud filtrate. However, potassium-salt muds are increasingly being used by the oil industry. The potassium cation is significantly different from the sodium cation in its radioactive and electrochemical properties. Natural potassium contains a radioactive isotope which emits gamma rays. Thus, the presence of potassium salts in the mud system may contribute to Gamma-Ray tool response. Since the Gamma Ray is used quantitatively in many geological sequences as an indicator of clay content, a way to correct for the effect of potassium in the mud column is desirable. Correction methods and charts based on laboratory measurements and field observations are presented. The effect of temperature on the resistivity of potassium muds is also briefly discussed. From data available, it appears to be similar to that for NaCl muds. On the bases of field observations and laboratory work, the electrochemical properties of potassium-chloride and potassium-carbonate muds and mud filtrates are discussed. Activity relationships are proposed, and the influence of these salts on the SP component potentials--namely, the liquid-junction, membrane, and bi-ionic potentials--is described. Several field examples are presented

  16. Biological properties of mud extracts derived from various spa resorts.

    Science.gov (United States)

    Spilioti, Eliana; Vargiami, Margarita; Letsiou, Sophia; Gardikis, Konstantinos; Sygouni, Varvara; Koutsoukos, Petros; Chinou, Ioanna; Kassi, Eva; Moutsatsou, Paraskevi

    2017-08-01

    Spa resorts are known for thousands of years for their healing properties and have been empirically used for the treatment of many inflammatory conditions. Mud is one of the most often used natural materials for preventive, healing and cosmetic reasons and although it has been used since the antiquity, little light has been shed on its physical, chemical and biological properties. In this study we examined the effect of mud extracts on the expression of adhesion molecules (CAMs) by endothelial cells as well as their effects on monocyte adhesion to activated endothelial cells. Most of mud extracts inhibited the expression of VCAM-1 by endothelial cells and reduced monocyte adhesion to activated endothelial cells, indicating a potent anti-inflammatory activity. Furthermore, the mud extracts were tested for their antimicrobial activity; however, most of them appeared inactive against S. aureus and S. epidermidis. One of the mud extracts (showing the best stabilization features) increased significantly the expression of genes involved in cell protection, longevity and hydration of human keratinocytes, such as, collagen 6A1, forkhead box O3, sirtuin-1, superoxide dismutase 1 and aquaporin-3. The present study reveals that mud exerts important beneficial effects including anti-inflammatory and anti-aging activity as well as moisturizing effects, implicating important cosmeceutical applications.

  17. Valorisation of waste ilmenite mud in the manufacture of sulphur polymer cement.

    Science.gov (United States)

    Contreras, Manuel; Gázquez, Manuel Jesús; García-Díaz, Irene; Alguacil, Francisco J; López, Félix A; Bolívar, Juan Pedro

    2013-10-15

    This paper reports the preparation of sulphur polymer cements (SPCs) incorporating waste ilmenite mud for use in concrete construction works. The ilmenite mud raw material and the mud-containing SPCs (IMC-SPCs) were characterised physico-chemically and radiologically. The optimal IMC-SPC mixture had a sulphur/mud ratio (w/w) of 1.05 (mud dose 20 wt%); this cement showed the greatest compressive strength (64 MPa) and the lowest water absorption coefficient (0.4 g cm(-2) at 28 days). Since ilmenite mud is enriched in natural radionuclides, such as radium isotopes (2.0·10(3) Bq kg(-1)(228)Ra and 5.0·10(2) Bq kg(-1)(226)Ra), the IMC-SPCs were subjected to leaching experiments, which showed their environmental impact to be negligible. The activity concentration indices for the different radionuclides in the IMC-SPCs containing 10% and 20% ilmenite mud met the demands of international standards for materials used in the construction of non-residential buildings. Copyright © 2013 Elsevier Ltd. All rights reserved.

  18. Mud Volcanoes - Analogs to Martian Cones and Domes (by the Thousands!)

    Science.gov (United States)

    Allen, Carlton C.; Oehler, Dorothy

    2010-01-01

    Mud volcanoes are mounds formed by low temperature slurries of gas, liquid, sediments and rock that erupt to the surface from depths of meters to kilometers. They are common on Earth, with estimates of thousands onshore and tens of thousands offshore. Mud volcanoes occur in basins with rapidly-deposited accumulations of fine-grained sediments. Such settings are ideal for concentration and preservation of organic materials, and mud volcanoes typically occur in sedimentary basins that are rich in organic biosignatures. Domes and cones, cited as possible mud volcanoes by previous authors, are common on the northern plains of Mars. Our analysis of selected regions in southern Acidalia Planitia has revealed over 18,000 such features, and we estimate that more than 40,000 occur across the area. These domes and cones strongly resemble terrestrial mud volcanoes in size, shape, morphology, associated flow structures and geologic setting. Geologic and mineralogic arguments rule out alternative formation mechanisms involving lava, ice and impacts. We are studying terrestrial mud volcanoes from onshore and submarine locations. The largest concentration of onshore features is in Azerbaijan, near the western edge of the Caspian Sea. These features are typically hundreds of meters to several kilometers in diameter, and tens to hundreds of meters in height. Satellite images show spatial densities of 20 to 40 eruptive centers per 1000 square km. Many of the features remain active, and fresh mud flows as long as several kilometers are common. A large field of submarine mud volcanoes is located in the Gulf of Cadiz, off the Atlantic coasts of Morocco and Spain. High-resolution sonar bathymetry reveals numerous km-scale mud volcanoes, hundreds of meters in height. Seismic profiles demonstrate that the mud erupts from depths of several hundred meters. These submarine mud volcanoes are the closest morphologic analogs yet found to the features in Acidalia Planitia. We are also conducting

  19. The role of porosity in discriminating between tsunami and hurricane emplacement of boulders — A case study from the Lesser Antilles, southern Caribbean

    Science.gov (United States)

    Spiske, Michaela; Böröcz, Zoltán; Bahlburg, Heinrich

    2008-04-01

    Coastal boulder deposits are a consequence of high-energy wave impacts, such as storms, hurricanes or tsunami. Parameters useful for distinguishing between hurricane and tsunami origins include distance of a deposit from the coast, boulder weight and inferred wave height. In order to investigate the role of porosity on boulder transport and elucidate the distinction between tsunami and hurricane impacts, we performed Archimedean and optical 3D-profilometry measurements for the determination of accurate physical parameters for porous reef and coral limestone boulders from the islands of Aruba, Bonaire and Curaçao (ABC Islands, Netherlands Antilles, Leeward Islands). Subsets of different coral species and lithotypes constituting the boulders were sampled, the physical parameters of boulders were analyzed, and each boulder component was attributed to a certain range of porosity and density. Lowest porosities were observed in calcarenite (5-8%), whereas highest porosities were measured for serpulid reef rock (47-68%). Porous serpulid reef rock (0.8-1.2 g/cm 3) and the coral Diploria sp. (0.6-1.0 g/cm 3) possess the lowest bulk densities, while less porous calcarenite (2.0-2.7 g/cm 3) and the coral Montastrea cavernosa yield the highest bulk density values (1.6-2.7 g/cm 3). The obtained physical parameters were used to calculate boulder weights and both hurricane and tsunami wave heights necessary to initiate transport of these boulders. Boulders are up to 5.6 times lighter than given in previously published data, and hence required minimum hurricane or tsunami waves are lower than hitherto assumed. The calculated wave heights, the high frequency of tropical storms and hurricanes in the southern Caribbean and the occurrence of boulders exclusively on the windward sides of the islands, implicate that for boulders on the ABC Islands a hurricane origin is more likely than a tsunami origin.

  20. Isoform-specific functions of Mud/NuMA mediate binucleation of Drosophila male accessory gland cells.

    Science.gov (United States)

    Taniguchi, Kiichiro; Kokuryo, Akihiko; Imano, Takao; Minami, Ryunosuke; Nakagoshi, Hideki; Adachi-Yamada, Takashi

    2014-12-20

    In standard cell division, the cells undergo karyokinesis and then cytokinesis. Some cells, however, such as cardiomyocytes and hepatocytes, can produce binucleate cells by going through mitosis without cytokinesis. This cytokinesis skipping is thought to be due to the inhibition of cytokinesis machinery such as the central spindle or the contractile ring, but the mechanisms regulating it are unclear. We investigated them by characterizing the binucleation event during development of the Drosophila male accessory gland, in which all cells are binucleate. The accessory gland cells arrested the cell cycle at 50 hours after puparium formation (APF) and in the middle of the pupal stage stopped proliferating for 5 hours. They then restarted the cell cycle and at 55 hours APF entered the M-phase synchronously. At this stage, accessory gland cells binucleated by mitosis without cytokinesis. Binucleating cells displayed the standard karyokinesis progression but also showed unusual features such as a non-round shape, spindle orientation along the apico-basal axis, and poor assembly of the central spindle. Mud, a Drosophila homolog of NuMA, regulated the processes responsible for these three features, the classical isoform Mud(PBD) and the two newly characterized isoforms Mud(L) and Mud(S) regulated them differently: Mud(L) repressed cell rounding, Mud(PBD) and Mud(S) oriented the spindle along the apico-basal axis, and Mud(S) and Mud(L) repressed central spindle assembly. Importantly, overexpression of Mud(S) induced binucleation even in standard proliferating cells such as those in imaginal discs. We characterized the binucleation in the Drosophila male accessory gland and examined mechanisms that regulated unusual morphologies of binucleating cells. We demonstrated that Mud, a microtubule binding protein regulating spindle orientation, was involved in this binucleation. We suggest that atypical functions exerted by three structurally different isoforms of Mud regulate

  1. Usage of Vermiculite as Additive Material in Water-Based Drilling Muds

    Directory of Open Access Journals (Sweden)

    Onur Eser Kök

    2018-05-01

    Full Text Available Drilling mud is used in drilling operations to ensure well stability and to transport the cut-offs to the surface and is generally classified as; Spud, Lignosulfonate and Polymer types. Spud Mud is the simple mud and mostly used at the beginning of drilling operations. It is mainly composed of bentonite and water. With increasing depth, It is hard to keep well stability and to carry cuttings from the bottom of hole to the surface with the basic drilling fluid. Thus, some materials are used to maintain the rheological and filtration properties of the mud. One of them is vermiculite that is a general name of the hydrated ferromagnesian aluminium silicate group. It has expanded properties when heated. Like all clay minerals, the cation exchange capacity is very high and very similar to the montmorillonites in terms of high cation exchange capacity. In this study, the usage of vermiculite as an additive material in drilling muds was investigated. Spud muds containing vermiculite in different amounts were prepared. Then rheological and filtration analysis of the muds were done according to American Petroleum Institute (API RP-13B-1 Standard. When evaluated the results, AV reached 41cP, PV 27cP, YP 28lb/100ft2 , 10 sec. gel strength 17lb/100ft2 , 10 min. gel strength 26 lb/100ft2 and filtration 9cc. The results showed that the vermiculite can might be used as a viscosifier and fluid loss reducing additive material in the drilling mud.

  2. Engineering Behavior and Characteristics of Wood Ash and Sugarcane Bagasse Ash

    Directory of Open Access Journals (Sweden)

    Francisco Grau

    2015-10-01

    Full Text Available Biomasses are organic materials that are derived from any living or recently-living structure. Plenty of biomasses are produced nationwide. Biomasses are mostly combusted and usually discarded or disposed of without treatment as biomass ashes, which include wood and sugarcane bagasse ashes. Thus, recycling or treatment of biomass ashes leads to utilizing the natural materials as an economical and environmental alternative. This study is intended to provide an environmental solution for uncontrolled disposal of biomass ashes by way of recycling the biomass ash and replacing the soils in geotechnical engineering projects. Therefore, in this study, characteristic tests of wood and sugarcane bagasse ashes that are considered the most common biomass ashes are conducted. The test of chemical compositions of biomass ashes is conducted using energy dispersive X-ray spectroscopy (EDS, and Scanning Electron Microscope (SEM, and heavy metal analysis is also conducted. Engineering behaviors including hydraulic conductivity, constrained modulus and shear modulus are examined. Also, coal fly ash Class C is used in this study for comparison with biomass ashes, and Ottawa 20/30 sands containing biomass ashes are examined to identify the soil replacement effect of biomass ashes. The results show that the particle sizes of biomass ashes are halfway between coal fly ash Class C and Ottawa 20/30 sand, and biomass ashes consist of a heterogeneous mixture of different particle sizes and shapes. Also, all heavy metal concentrations were found to be below the US Environmental Protection Agency (EPA maximum limit. Hydraulic conductivity values of Ottawa 20/30 sand decrease significantly when replacing them with only 1%–2% of biomass ashes. While both the constrained modulus and shear modulus of biomass ashes are lower than Ottawa 20/30 sand, those of mixtures containing up to 10% biomass ashes are little affected by replacing the soils with biomass ashes.

  3. Seismic-sequence stratigraphy and geologic structure of the Floridan aquifer system near "Boulder Zone" deep wells in Miami-Dade County, Florida

    Science.gov (United States)

    Cunningham, Kevin J.

    2015-01-01

    The U.S. Geological Survey, in cooperation with the Miami-Dade Water and Sewer Department, acquired, processed, and interpreted seismic-reflection data near the North and South District “Boulder Zone” Well Fields to determine if geologic factors may contribute to the upward migration of injected effluent into that upper part of the Floridan aquifer system designated by the U.S. Environmental Protection Agency as an underground source of drinking water. The depth of the Boulder Zone at the North and South District “Boulder Zone” Well Fields ranges from about 2,750 to 3,300 feet below land surface (ft bls), whereas overlying permeable zones used as alternative drinking water supply range in depth from about 825 to 1,580 ft bls at the North and South District “Boulder Zone” Well Fields. Seismic-sequence stratigraphy and geologic structures imaged on seismic-reflection profiles created for the study describe the part of the Floridan aquifer system overlying and within the Boulder Zone. Features of the Floridan aquifer system underlying the Boulder Zone were not studied because seismic-reflection profiles acquired near the North and South District “Boulder Zone” Well Fields lacked adequate resolution at such depths.

  4. Inscuteable Regulates the Pins-Mud Spindle Orientation Pathway

    Science.gov (United States)

    Mauser, Jonathon F.; Prehoda, Kenneth E.

    2012-01-01

    During asymmetric cell division, alignment of the mitotic spindle with the cell polarity axis ensures that the cleavage furrow separates fate determinants into distinct daughter cells. The protein Inscuteable (Insc) is thought to link cell polarity and spindle positioning in diverse systems by binding the polarity protein Bazooka (Baz; aka Par-3) and the spindle orienting protein Partner of Inscuteable (Pins; mPins or LGN in mammals). Here we investigate the mechanism of spindle orientation by the Insc-Pins complex. Previously, we defined two Pins spindle orientation pathways: a complex with Mushroom body defect (Mud; NuMA in mammals) is required for full activity, whereas binding to Discs large (Dlg) is sufficient for partial activity. In the current study, we have examined the role of Inscuteable in mediating downstream Pins-mediated spindle orientation pathways. We find that the Insc-Pins complex requires Gαi for partial activity and that the complex specifically recruits Dlg but not Mud. In vitro competition experiments revealed that Insc and Mud compete for binding to the Pins TPR motifs, while Dlg can form a ternary complex with Insc-Pins. Our results suggest that Insc does not passively couple polarity and spindle orientation but preferentially inhibits the Mud pathway, while allowing the Dlg pathway to remain active. Insc-regulated complex assembly may ensure that the spindle is attached to the cortex (via Dlg) before activation of spindle pulling forces by Dynein/Dynactin (via Mud). PMID:22253744

  5. Dead Sea mud packs for chronic low back pain.

    Science.gov (United States)

    Abu-Shakra, Mahmoud; Mayer, Amit; Friger, Michael; Harari, Marco

    2014-09-01

    Low back pain (LBP) is chronic disease without a curative therapy. Alternative and complementary therapies are widely used in the management of this condition. To evaluate the efficacy of home application of Dead Sea mud compresses to the back of patients with chronic LBP. Forty-six consecutive patients suffering from chronic LBP were recruited. All patients were followed at the Soroka University Rheumatic Diseases Unit. The patients were randomized into two groups: one group was treated with mineral-rich mud compresses, and the other with mineral-depleted compresses. Mud compresses were applied five times a week for 3 consecutive weeks. The primary outcome was the patient's assessment of the overall back pain severity. The score of the Ronald & Morris questionnaire served as a secondary outcome. Forty-four patients completed the therapy and the follow-up assessments: 32 were treated with real mud packs and 12 used the mineral-depleted packs. A significant decrease in intensity of pain, as described by the patients, was observed only in the treatment group. In this group, clinical improvement was clearly seen at completion of therapy and was sustained a month later. Significant improvement in the scores of the Roland & Morris questionnaire was observed in both groups. The data suggest that pain severity was reduced in patients treated with mineral-rich mud compresses compared with those treated with mineral-depleted compresses. Whether this modest effect is the result of a "true" mud effect or other causes can not be determined in this study.

  6. Determination of rare earth elements in red mud by ICP-MS

    International Nuclear Information System (INIS)

    Kumar, Sanjukta A.; Suvarna, S.; Kiran Kumar, G.

    2017-01-01

    Red mud or red sludge is a highly alkaline waste product composed mainly of iron oxide that is generated in the industrial production of aluminum from bauxite. With about 77 million tons of this hazardous material being produced annually, red mud poses a serious disposal problem in the mining industry. Discharge of red mud is hazardous environmentally because of its alkalinity. Many studies have been conducted to develop uses of red mud. An estimated 2 to 3 million tones are used annually in the production of cement, road construction and as a source for iron. Potential applications include the production of low cost concrete, application to sandy soils to improve phosphorus cycling, amelioration of soil acidity, landfill capping and carbon sequestration. Red mud contains a large amount of iron along with appreciable concentrations of many strategic elements such as rare earth elements and therefore can be a source of valuable secondary raw material. This necessitates the elemental characterization of red mud. This paper presents an effective dissolution procedure using a mixture of phosphoric acid and nitric acid for red mud followed by determination of rare earth elements by ICP-MS. The method was validated by spike recovery experiments. The recoveries were found within 98 to 102 %. The relative standard deviation (RSD) of the method was found to be within 5 %

  7. Ecological effects of low toxicity oil-based mud drilling in the Beatrice oilfield

    Energy Technology Data Exchange (ETDEWEB)

    Addy, J M; Hartley, J P; Tibbetts, P J.C.

    1984-12-01

    To investigate the effects of drilling discharges on the seabed fauna, surveys were carried out in the Beatrice oilfield after drilling 13 wells with water-based muds, and then after one and five further wells had been drilled using low toxicity oil-based muds. Localized benthic effects were found after the water-based mud drilling. After the use of oil-based muds, the nature of the effects was different, although there was little increase in the area involved. Possible reasons for this are discussed and burial and organic enrichment are suggested as the major influences. It is concluded that the use of low toxicity oil-based mud at Beatrice has resulted in only limited benthic effects, suggesting that the use of these muds is environmentally acceptable.

  8. Reagent for treating clay drilling muds

    Energy Technology Data Exchange (ETDEWEB)

    Tkachenko, P V; Leshchinskiy, P A; Shnaper, B I; Zinchuk, I F; Zlobin, V P

    1982-01-01

    A reagent is proposed for treating clay drilling muds. It contains lignite, caustic soda and modifying agent. It is distinguished by the fact that in order to reduce the cost of the reagent with simultaneous decrease in the viscosity and static shear stress of the drilling mud, it additionally contains iron sulfate, and the modifying agent contained is wastes of carbonic acid production with the following ratio of components (parts by weight): lignite 10.0-15.0, caustic soda 2.0-3.0, wastes of carbonic acid production 0.5-0.75; iron sulfate 1.0-2.0.

  9. Removal of hexavalent chromium by using red mud activated with cetyltrimethylammonium bromide.

    Science.gov (United States)

    Li, Deliang; Ding, Ying; Li, Lingling; Chang, Zhixian; Rao, Zhengyong; Lu, Ling

    2015-01-01

    The removal of hexavalent chromium [Cr(VI)] from aqueous solution by using red mud activated with cetyltrimethylammonium bromide (CTAB) was studied. The optimum operation parameters, such as CTAB concentration, pH values, contact time, and initial Cr(VI) concentration, were investigated. The best concentration of CTAB for modifying red mud was found to be 0.50% (mCTAB/VHCl,0.6 mol/L). The lower pH (mud activated with CTAB can greatly improve the removal ratio of Cr(VI) as high as four times than that of original red mud. Adsorption equilibrium was reached within 30 min under the initial Cr(VI) concentration of 100 mg L(-1). The isotherm data were analysed using Langmuir and Freundlich models. The adsorption of Cr(VI) on activated red mud fitted well to the Langmuir isotherm model, and the maximum adsorption capacity was estimated as 22.20 mg g(-1) (Cr/red mud). The adsorption process could be well described using the pseudo-second-order model. The result shows that activated red mud is a promising agent for low-cost water treatment.

  10. Investigation of the Dashigil mud volcano (Azerbaijan) using beryllium-10

    Energy Technology Data Exchange (ETDEWEB)

    Kim, K.J., E-mail: kjkim@kigam.re.kr [Korea Geological Research Division, Korea Institute of Geoscience and Mineral Resources, Daejeon 305-350 (Korea, Republic of); Baskaran, M.; Jweda, J. [Department of Geology, Wayne State University, Detroit, MI 48202 (United States); Feyzullayev, A.A.; Aliyev, C. [Geology Institute of the Azerbaijan National Academy of Sciences (ANAS), Baku, AZ 1143 (Azerbaijan); Matsuzaki, H. [MALT, University of Tokyo, Tokyo (Japan); Jull, A.J.T. [NSF Arizona AMS Lab, University of Arizona, AZ 85721 (United States)

    2013-01-15

    We collected and analyzed five sediments from three mud volcano (MV) vents and six suspended and bottom sediment samples from the adjoining river near the Dashgil mud volcano in Azerbaijan for {sup 10}Be. These three MV are found among the 190 onshore and >150 offshore MV in this region which correspond to the western flank of the South Caspian depression. These MVs overlie the faulted and petroleum-bearing anticlines. The {sup 10}Be concentrations and {sup 10}Be/{sup 9}Be ratios are comparable to the values reported for mud volcanoes in Trinidad Island. It appears that the stable Be concentrations in Azerbaijan rivers are not perturbed by anthropogenic effects and are comparable to the much older sediments (mud volcano samples). The {sup 10}Be and {sup 9}Be concentrations in our river sediments are compared to the global data set and show that the {sup 10}Be values found for Kura River are among the lowest of any river for which data exist. We attribute this low {sup 10}Be concentration to the nature of surface minerals which are affected by the residual hydrocarbon compounds that occur commonly in the study area in particular and Azerbaijan at large. The concentrations of {sup 40}K and U-Th-series radionuclides ({sup 234}Th, {sup 210}Pb, {sup 226}Ra, and {sup 228}Ra) indicate overall homogeneity of the mud volcano samples from the three different sites. Based on the {sup 10}Be concentrations of the mud volcano samples, the age of the mud sediments could be at least as old as 4 myr.

  11. A drilling mud for drilling wells in collapsing rocks

    Energy Technology Data Exchange (ETDEWEB)

    Bochkarev, G P; Anderson, B A; Minkhayrov, K A; Sharipov, A U

    1982-01-01

    In a known drilling mud for drilling wells in collapsing rocks, which contains clay, sodium silicate and polyacrylamide (PAA), in order to increase its specific electrical resistance and to increase the strengthening properties, a silicoorganic liquid is additionally introduced into its composition with the following component ratio (percent): clay, 5 to 7; sodium silicate, 5 to 7; polyacrylamide, 0.3 to 0.5; silicoorganic liquid, GKZh-94, 0.5 to 1.5 and water, the remainder. The GKZh-94 is a chemical compound based on alkylphenylchlorsilanes and substituted ethers of orthosilicic acid, used for waterproofing fabrics and soils. The addition of GKZh-94 provides the required values of the specific electric resistance of the mud and does not distort the gas logging indications. The proposed mud has low water production (4 to 6 cubic centimeters), optimal viscosity (25 to 31 seconds) and high structural and mechanical properties. Its strengthening properties are substantially above those of the known mud.

  12. Binding of Vapour-Phase Mercury (Hg0) on Chemically Treated Bauxite Residues (Red Mud)

    Science.gov (United States)

    In this study, Hg capture using red mud, seawater-neutralized red mud, and acid-treated red mud is evaluated and compared to other, more conventional sorbent materials. Red mud (also known as bauxite residue) is a by-product of extracting alumina from ground bauxite ore by treati...

  13. AML (Advanced Mud Logging: First Among Equals

    Directory of Open Access Journals (Sweden)

    T. Loermans

    2017-09-01

    Full Text Available During the past ten years an enormous development in mud logging technology has been made. Traditional mud logging was only qualitative in nature, and mudlogs could not be used for the petrophysical well evaluations which form the basis for all subsequent activities on wells and fields. AML however can provide quantitative information, logs with a reliability, trueness and precision like LWD and WLL. Hence for well evaluation programmes there are now three different logging methods available, each with its own pros and cons on specific aspects: AML, LWD and WLL. The largest improvements have been made in mud gas analysis and elemental analysis of cuttings. Mud gas analysis can yield hydrocarbon fluid composition for some components with a quality like PVT analysis, hence not only revolutionising the sampling programme so far done with only LWD/WLL, but also making it possible to geosteer on fluid properties. Elemental analysis of cuttings, e.g. with XRF, with an ability well beyond the capabilities of the spectroscopy measurements possible earlier with LWD/WLL tools, is opening up improved ways to evaluate formations, especially of course where the traditional methods are falling short of requirements, such as in unconventional reservoirs. An overview and specific examples of these AML logs is given, from which it may be concluded that AML now ought to be considered as “first among its equals”.

  14. CO2 flux from Javanese mud volcanism.

    Science.gov (United States)

    Queißer, M; Burton, M R; Arzilli, F; Chiarugi, A; Marliyani, G I; Anggara, F; Harijoko, A

    2017-06-01

    Studying the quantity and origin of CO 2 emitted by back-arc mud volcanoes is critical to correctly model fluid-dynamical, thermodynamical, and geochemical processes that drive their activity and to constrain their role in the global geochemical carbon cycle. We measured CO 2 fluxes of the Bledug Kuwu mud volcano on the Kendeng Fold and thrust belt in the back arc of Central Java, Indonesia, using scanning remote sensing absorption spectroscopy. The data show that the expelled gas is rich in CO 2 with a volume fraction of at least 16 vol %. A lower limit CO 2 flux of 1.4 kg s -1 (117 t d -1 ) was determined, in line with the CO 2 flux from the Javanese mud volcano LUSI. Extrapolating these results to mud volcanism from the whole of Java suggests an order of magnitude total CO 2 flux of 3 kt d -1 , comparable with the expected back-arc efflux of magmatic CO 2 . After discussing geochemical, geological, and geophysical evidence we conclude that the source of CO 2 observed at Bledug Kuwu is likely a mixture of thermogenic, biogenic, and magmatic CO 2 , with faulting controlling potential pathways for magmatic fluids. This study further demonstrates the merit of man-portable active remote sensing instruments for probing natural gas releases, enabling bottom-up quantification of CO 2 fluxes.

  15. Conditioning of red mud for subsequent titanium and scandium recovery. A conceptual design study

    Energy Technology Data Exchange (ETDEWEB)

    Alkan, G.; Xakalashe, B.; Kaussen, F.; Friedrich, Bernd [RWTH Aachen Univ. (Germany). IME Inst. of Process Metallurgy and Metal Recycling; Yagmurlu, B. [RWTH Aachen Univ. (Germany). IME Inst. of Process Metallurgy and Metal Recycling; MEAB Chemie Technik GmbH, Aachen (Germany)

    2017-03-15

    Leaching experiments were undertaken on red mud materials (red mud and red mud slag). The red mud slag was produced via the carbothermic reduction of red mud at high temperatures (T > 1500 C) via SAF treatment. Furthermore, iron was recovered in the smelting step to the metal phase. Ti and Sc were successfully recovered from the red mud materials by hydrometallurgical treatment. For both critical metals, it was found that sulfuric acid was the best mineral acid among others. Since direct red mud leaching had some shortcomings, a route designed to overcome them is proposed. For optimal Ti and Sc recovery from red mud a promising process flowsheet combining pyrometallurgical and hydrometallurgical treatment is proposed as follows: pyrometallurgical processing (fluxed smelting to produce calcium oxide based slag phases and controlled cooling for crystalline and glassy slags), leaching for maximized Ti- and Sc extraction and followed by a multistage precipitation (for metal recovery and solution purification). Initial trial results showed that the proposed process is promising.

  16. Natural radionuclides in bauxitic tailings (Red-Mud) in the Gulf of Corinth, Greece

    International Nuclear Information System (INIS)

    Papatheodorou, G.; Maratou, A.; Ferentinos, G.; Papaefthymiou, H.

    2004-01-01

    A detailed environmental survey was carried out in the central Gulf of Corinth in order to determine radionuclides in the bauxite ed-mud tailings which have been discharged on the sea floor by a Bauxite Processing Plant (Aluminio Ellados A.E). The discharge of bauxitic tailings via two pipelines at a water depth of 100 m, in Antikyra Bay (Northern Gulf of Corinth), has resulted in the formation of two red-mud mound-like deposits. The red-mud deposits at the mouth of the out falls, are not stable and very often red-mud masses are detached from the two main deposits and are transported to the Corinth central basin, by turbidity currents, at a water depth of 850 m and about 17 km away from the main deposits. Thus, at the Antikyra bay, the red-mud has formed a surficial veneer (0.5-2.0 cm) on the sea floor. On the Corinth central basin floor the red mud has formed successive red-mud layers which are interrupted by layers of natural mud. Fifteen gravity cores have been selected from the studied area and a number of bauxite samples have been collected from mines that supply the bauxite processing plant. Red-mud, natural mud and bauxite samples were analyzed for 238 U 226 Ra, 232 Th, 40 K, and 137 Cs by direct gamma spectrometry. The study of radionuclides concentrations has shown that: (a) the enrichment factor of radionuclides in the red-mud in the main deposit at the mouth of the out falls, in relation to bauxite samples, is about 2.0, (b) the enrichment factor of 238 U, 226 Ra and 232 Th in the red-mud in the main deposit and the central basin, in relation to natural sediments below, is visibly higher than 1.0 (2.0-19.0) whilst 40 K exhibits the opposite trend, and (c) the enrichment/dilution factor of radionuclides in the red-mud surficial veneer at the Antikyra Bay, in relation to the natural sediments below, is ranging between 0.4 and 3.5. (author)

  17. The anaerobic digestion of organic matter in sugarbeet mud

    NARCIS (Netherlands)

    Keizer, M.G.; Haan, de F.A.M.; Blom, J.J.C.; Knaapen, J.W.P.M.

    1981-01-01

    Storage of sugar-beet mud in the traditional way, i.e., direct dewatering after pumping the slurry in storage basins, may cause odor nuisance because of digestion of organic substances. In order to prevent these bad odor problems the mud should remain submerged during the digestion period. No

  18. Ash Utilisation 2012. Ashes in a Sustainable Society. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2012-11-01

    Conference themes: Risk assessment, Fly ash- Road construction, Recycling and Greenhouse gases, Storage of ashes, Fertilizer, Metal Mining, Support and Barriers, Construction Material, Civil Engineering, and MSWI bottom ash.

  19. MUD and Self Efficacy.

    Science.gov (United States)

    Lee, Kwan Min

    2000-01-01

    Proposes a theoretical framework for analyzing the effect of MUD (Multi-User Dungeons) playing on users' self-efficacy by applying Bandura's social learning theory, and introduces three types of self-efficacy: computer self-efficacy; social self-efficacy; and generalized self-efficacy. Considers successful performance, vicarious experience,…

  20. Aerobic Degradation of Drill Muds by Axenic and Mixed Bacterial ...

    African Journals Online (AJOL)

    Prof. Ogunji

    significant difference in the degradation of the drilling muds by the isolates (p > 0.05). ... the potentials of some indigenous bacteria to biodegrade drilling muds used in ... transported to the laboratory aseptically for evaluation, in labeled plastic.

  1. The "Mud-volcanoes route" (Emilia Apennines, northern Italy)

    Science.gov (United States)

    Coratza, Paola; Castaldini, Doriano

    2016-04-01

    In the present paper the "Mud-volcanoes route" (MVR), an itinerary unfolds across the districts of Viano, Sassuolo, Fiorano Modenese and Maranello, in which part of the Emilia mud volcanoes fields are located, is presented. The Mud-volanoes route represents an emotional journey that connects places and excellences through the geological phenomenon of mud volcanoes, known with the local name "Salse". The Mud Volcanoes are created by the surfacing of salt water and mud mixed with gaseous and liquid hydrocarbons along faults and fractures of the ground. The name "Salsa"- from Latin salsus - results from the"salt" content of these muddy waters, ancient heritage of the sea that about a million years ago was occupying the current Po Plain. The "Salse" may take the shape of a cone or a level-pool according to the density of the mud. The Salse of Nirano, in the district of Fiorano Modenese, is one of the most important in Italy and among the most complex in Europe. Less extensive but equally charming and spectacular, are the "Salse" located in the districts of Maranello (locality Puianello), Sassuolo (locality Montegibbio) and Viano (locality Casola Querciola and Regnano). These fascinating lunar landscapes have always attracted the interest of researchers and tourist.The presence on the MVR territory of ancient settlements, Roman furnaces and mansions, fortification systems and castles, besides historic and rural buildings, proves the lasting bond between this land and its men. In these places, where the culture of good food has become a resource, we can find wine cellars, dairy farms and Balsamic vinegar factories that enable us to appreciate unique worldwide products. This land gave also birth to some personalities who created unique worldwide famous values, such as the myth of the Ferrrari, the ceramic industry and the mechatronics. The MVR is represented in a leaflet containing, short explanation, photos and a map in which are located areas with mud volcanoes, castles

  2. 78 FR 79436 - Boulder Canyon Project-Post-2017 Resource Pool

    Science.gov (United States)

    2013-12-30

    ... customers of electric utilities. The marketing criteria should include municipal corporations and political... Pool AGENCY: Western Area Power Administration, DOE. ACTION: Notice of final marketing criteria and... marketing agency of the Department of Energy (DOE), announces the Boulder Canyon Project (BCP) post-2017...

  3. Delay Pressure Detection Method to Eliminate Pump Pressure Interference on the Downhole Mud Pressure Signals

    Directory of Open Access Journals (Sweden)

    Yue Shen

    2013-01-01

    Full Text Available The feasibility of applying delay pressure detection method to eliminate mud pump pressure interference on the downhole mud pressure signals is studied. Two pressure sensors mounted on the mud pipe in some distance apart are provided to detect the downhole mud continuous pressure wave signals on the surface according to the delayed time produced by mud pressure wave transmitting between the two sensors. A mathematical model of delay pressure detection is built by analysis of transmission path between mud pump pressure interference and downhole mud pressure signals. Considering pressure signal transmission characteristics of the mud pipe, a mathematical model of ideal low-pass filter for limited frequency band signal is introduced to study the pole frequency impact on the signal reconstruction and the constraints of pressure sensor distance are obtained by pole frequencies analysis. Theoretical calculation and numerical simulation show that the method can effectively eliminate mud pump pressure interference and the downhole mud continuous pressure wave signals can be reconstructed successfully with a significant improvement in signal-to-noise ratio (SNR in the condition of satisfying the constraints of pressure sensor distance.

  4. Mud diaprism and it's effect on the hydrocarbon system in the south Caspian

    International Nuclear Information System (INIS)

    Baganz, O.W.; Ballard, J.H.; Krenov, M.

    2002-01-01

    Full text : Mud diapirism plays a special role in the geology and petroleum system of the south Caspian basin. Hundreads of mud intrusions penetrate the thick Plio-Pleistocene section. This article talks in detail about aspects of the influence of mud diapirs and their related with mud volcanoes on the generation and trapping of hydrocarbons. Some of these aspects are : 1) The influence on the sedimentation; 2) Structural impact; 3) Stress and strain in the surrounded formations; 4) Thermal effect; 5) Pressure effect. All these aspects of the diapiric and mud-volcanic activity should be kept in mind during the volumetric calculations and play evaluation.

  5. Status of the mud crab fishery in Kenya: A review | Mirera | Western ...

    African Journals Online (AJOL)

    In Kenya, mud crabs are fished mainly by men and to a lesser extent by women and children due to the accessibility of the fishing areas by foot. This makes mud crabs a key fishery that is easily accessible for exploitation by most coastal artisanal fishers for subsistence and commercial purposes. Mud crabs have been a ...

  6. Designing a suitable alternative to oil-based mud

    International Nuclear Information System (INIS)

    Holgate, M.; Irwin, G.; Cousins, L.

    1991-01-01

    This paper reports on wireline logging problems which have plagued the reservoir section of development wells in Welton oil field in the East Midlands area of England. And resulting incomplete or poor-quality logging data spurred a look at ways of improving hole conditions. Oil-based muds often are seen as the ideal solution, but they are expensive. Their use also commits the operator to additional costs from safeguarding personnel and limiting environmental impact. Such expense was initiated to develop a cheaper, more environmentally friendly, water-based alternative. A wide-ranging review was carried out to determine the most cost-effective options to obtain reservoir information. This included an examination of lithology, casing design, bit selection, hydraulics, logging requirements and techniques, and development of a suitable water-based mud. This holistic approach was seen as the most effective method of avoiding use of oil-based mud. After successful experimentation, a water-based mud was used in subsequent wells at Welton. A high-salt mud system and the drilling principles discussed here produced significant improvement in hole conditions. Application of a holistic approach led to many operational improvements. For instance, the casing shoe was deepened to case off the most troublesome zone in the local Edlington formation. There also was a better awareness of alternative logging techniques, the commercial factors that influenced their use and their operational and technical limitations. Logging problems were reduced but not eliminated. Where there were problems, application of improved techniques minimized their impact. Last, but not least, there was an unexpected spin-off in that the bit chosen to reduce hole erosion also reduced the time taken to drill the section

  7. Particularies of recultivation of bore muds on oil-gas fields of Tyumen region

    Science.gov (United States)

    Petuhova, V. S.; Skipin, L. N.; Skipin, D. L.; Gaevaya, E. V.

    2017-10-01

    The article reflects negative physical and chemical properties of the bore muds in respect to Tyumen region (high dispersion, swelling ability, ash structure, crust formation, low filterability, a high degree of salinization, alkalinity and toxicity). Indicated properties are mainly stipulated by the increased content of exchangeable sodium in the absorbing complex and by the presence of soda in aqueous solution. The source of absorbed sodium and soda in water extract is the use of caustic soda in the drilling mixture. It was found out that these negative properties are illuminated using coagulant in a form of phosphogypsum - waste of chemical industry. Necessity in the nitrogen for the bean cultures-phytomeliorants is provided at the expense of legume bacteria in a form of the rizotorphin formulation. It is worth noting that growing of legume bacteria in extremely salted breeding ground on the leguminous agar has allowed choosing the most salt resistant species among the numerous strains of Melilotus officinalis and medicago. The presence of phosphorus in phosphogypsum positively influences the productivity of leguminous crops in the beginning of recultivation.

  8. Seafloor monitoring for synthetic-based mud discharged in the Western Gulf of Mexico

    International Nuclear Information System (INIS)

    Candler, J.E.; Hoskin, S.; Churan, M.

    1995-01-01

    Synthetic-based muds have been used to simultaneously improve drilling and environmental performance. The fate and effects of synthetic-based mud discharges in the marine environment have been issues of concern with the drilling industry and governmental agencies. Most of the environmental data on synthetic-based muds have been generated under laboratory conditions. This study uses field-collected data to investigate, the fate and effects of a polyalphaolefin synthetic-based drilling fluid. The first well drilled in the Gulf of Mexico using synthetic-based mud was completed in June 1992. Approximately 441 bbl of cuttings and 354 bbl of synthetic-based mud were discharged over a 9-day period. Three sampling trips have been made to the discharge location to collect sediment samples for chemical and biological analysis over a 2-year period. The sediment samples were analyzed for content of organic compounds and barium. On the third trip, infaunal samples were also taken. Information collected from the chemical and biological analysis is documented and compared to similar field studies performed on oil-based and water-based muds. Sampling techniques and analytical protocols are described to facilitate future studies. Two years after discharges of synthetic-based cuttings were completed, an area within 50 m of the discharge point continued to exhibit alterations in the benthic community not normally associated with water-based mud discharges. However, the study indicates that polyalphaolefin synthetic-based mud exhibits significant improvements over oil-based mud in terms of removal of organic contamination and minimization of adverse effects on the benthic community

  9. A comparative study of mud-like and coralliform calcium carbonate gallbladder stones.

    Science.gov (United States)

    Ma, Rui-Hong; Luo, Xiao-Bing; Wang, Xiao-Feng; Qiao, Tie; Huang, Hai-Yi; Zhong, Hai-Qiang

    2017-07-01

    To gain insight to underlying mechanism of the formation of calcium carbonate (CaCO 3 ) gallbladder stones, we did comparative study of stones with mud appearance and those with coralliform appearance. A total of 93 gallbladder stones with mud appearance and 50 stones with coralliform appearance were analyzed. The appearance, color, texture, and the detection of Clonorchis sinensis eggs by microscopic examination were compared between the two groups. Then, the material compositions of stones were analyzed using Fourier Transform Infrared spectroscopy and the spectrogram characteristics were compared. Moreover, microstructure characteristics of the two kinds of stones were observed and compared with Scanning Electron Microscopy. Mud-like gallbladder stones were mainly earthy yellow or brown with brittle or soft texture, while coralliform stones were mainly black with extremely hard texture, the differences between the two groups was significant (p mud-like gallbladder stones were CaCO 3 stones, and mainly aragonite; while all of the coralliform stones were CaCO 3 stones, and mainly calcite (p mud-like CaCO 3 stones was lower than that in coralliform CaCO 3 stones (p Mud-like CaCO 3 stones mainly happened to patients with cystic duct obstruction. Clonorchis sinensis infection was mainly associated with coralliform (calcite) CaCO 3 stones. Cystic duct obstruction was mainly associated with mud-like (aragonite) CaCO 3 stones. © 2017 Wiley Periodicals, Inc.

  10. Mineralogical and geochemical study of mud volcanoes in north ...

    African Journals Online (AJOL)

    The gulf of Cadiz is one of the most interesting areas to study mud volcanoes and structures related to cold fluid seeps since their discovery in 1999. In this study, we present results from gravity cores collected from Ginsburg and Meknes mud volcanoes and from circular structure located in the gulf of Cadiz (North Atlantic ...

  11. Biomass ash utilization

    Energy Technology Data Exchange (ETDEWEB)

    Bristol, D.R.; Noel, D.J.; O`Brien, B. [HYDRA-CO Operations, Inc., Syracuse, NY (United States); Parker, B. [US Energy Corp., Fort Fairfield, ME (United States)

    1993-12-31

    This paper demonstrates that with careful analysis of ash from multiple biomass and waste wood fired power plants that most of the ash can serve a useful purpose. Some applications require higher levels of consistency than others. Examples of ash spreading for agricultural purposes as a lime supplement for soil enhancement in Maine and North Carolina, as well as a roadbase material in Maine are discussed. Use of ash as a horticultural additive is explored, as well as in composting as a filtering media and as cover material for landfills. The ash utilization is evaluated in a framework of environmental responsibility, regulations, handling and cost. Depending on the chemical and physical properties of the biomass derived fly ash and bottom ash, it can be used in one or more applications. Developing a program that utilizes ash produced in biomass facilities is environmentally and socially sound and can be financially attractive.

  12. HEAVY METALS IN SURFACE MUD SEDIMENT IN EKATERINBURG (RUSSIA

    Directory of Open Access Journals (Sweden)

    A. A. Seleznev

    2018-03-01

    Full Text Available Problem Statement. Now the most part of the world’s population lives in cities, thus, it is relevant the search for universal, low-cost and express methods for environmental geochemical investigations of an urban environment. The objective of the study is the assessment of content and properties of surface mud sediment at the urban territory (on the example of Ekaterinburg, Russia. Methods of the study. The 30 samples of surface mud sediment, soils and ground were collected in the residential area of the city. Particle size composition, measurements of heavy metals content, correlation analysis was conducted for the samples. Results. Surface mud sediment at the residential territories can be classified as surface facie of the recent anthropogenic sediment. Samples of the environmental compartments were collected at the territories of six blocks of houses of various years of construction, located in various parts of the city and at the various geological units. Five samples were collected in each block: 3 samples within the block and 2 samples – outside. The content of Pb, Zn, Cu, Ni, Co, and Mn was measured in particle size fractions of the samples. Particle size composition of the surface mud sediment in Ekaterinburg is similar to the particle size composition of the grounds formed on the sediments of Holocene age in Urals region. The positive statistically significant correlation was found between the couples of metals: Zn and Pb, Zn and Cu, Co and Ni. The distribution of concentrations of Pb, Zn and Cu over particle size fractions of surface mud sediment is heterogeneous. Pollution of the ground and soil in urban areas is due to the transition of heavy metals with particles of dust and fine sand. Typical geochemical association of metals for particle size fraction of surface mud sediment 0.002–0.01 mm – Mn-Zn-Ni-Cu-Pb-Co, that is similar to the association for sediments of surface puddles in local zones of relief, soils and bottom

  13. Experimental study and mechanism analysis of modified limestone by red mud for improving desulfurization

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Hongtao; Han, Kuihua; Niu, Shengli; Lu, Chunmei; Liu, Mengqi; Li, Hui [Shandong Univ., Jinan (China). School of Energy and Power Engineering

    2013-07-01

    Red mud is a type of solid waste generated during alumina production from bauxite, and how to dispose and utilize red mud in a large scale is yet a question with no satisfied answer. This paper attempts to use red mud as a kind of additive to modify the limestone. The enhancement of the sulfation reaction of limestone by red mud (two kinds of Bayer process red mud and one kind of sintering process red mud) are studied by a tube furnace reactor. The calcination and sulfation process and kinetics are investigated in a thermogravimetric (TG) analyzer. The results show that red mud can effectively improve the desulfurization performance of limestone in the whole temperature range (1,073-1,373K). Sulfur capacity of limestone (means quality of SO{sub 2} which can be retained by 100mg of limestone) can be increased by 25.73, 7.17 and 15.31% while the utilization of calcium can be increased from 39.68 to 64.13%, 60.61 and 61.16% after modified by three kinds of red mud under calcium/metallic element (metallic element described here means all metallic elements which can play a catalytic effect on the sulfation process, including the Na, K, Fe, Ti) ratio being 15, at the temperature of 1,173K. The structure of limestone modified by red mud is interlaced and tridimensional which is conducive to the sulfation reaction. The phase composition analysis measured by XRD of modified limestone sulfated at high temperature shows that there are correspondingly more sulphates for silicate and aluminate complexes of calcium existing in the products. Temperature, calcium/metallic element ratio and particle diameter are important factors as for the sulfation reaction. The optimum results can be obtained as calcium/metallic element ratio being 15. Calcination characteristic of limestone modified by red mud shows a migration to lower temperature direction. The enhancement of sulfation by doping red mud is more pronounced once the product layer has been formed and consequently the promoting

  14. Rare gas constraints on the history of Boulder 1, Station 2, Apollo 17

    International Nuclear Information System (INIS)

    Leich, D.A.; Kahl, S.B.; Kirschbaum, A.R.; Niemeyer, S.; Phinney, D.

    1975-01-01

    Rare gas isotopic analyses have been performed on both pile-irradiated and unirradiated samples from Boulder 1, Station 2. Two samples from rock 72255, the Civet Cat clast and a sample of adjacent breccia, have concordant 40 Ar- 39 Ar ages of 3.99 +- 0.03 b.y. and 4.01 +- 0.03 b.y., respectively. Several samples from rock 72275 have complex thermal release patterns with no datable features, but an intermediate temperature plateau from the dark rim material of the Marble Cake clast yields an age of 3.99 +- 0.03 b.y., indistinguishable from the age of rock 72255. We regard these ages as upper limits on the time of the Serenitatis basin-forming event. The absence of fossil solar-wind trapped gases in the breccia samples implies that a prior existence for the boulder as near-surface regolith material can be regarded as extremely unlikely. Instead, the small trapped rare-gas components have isotopic and elemental compositions diagnostic of the terrestrial-type trapped component which has previously been identified in several Apollo 16 breccias and in rock 14321. Excess fission Xe is found in all Boulder 1 samples in approximately 1:1 proportions with Xe from spontaneous fission of 238 U. This excess fission Xe is attributed to spontaneous fission of 244 Pu in situ. Cosmic-ray exposure ages for samples from rocks 72215 and 72255 are concordant with mean 81 Kr-Kr exposure ages of 41.4 +- 1.4 m.y. and 44.1 +- 3.3 m.y., respectively. However, a distinctly different 81 Kr-Kr exposure age of 52.5 +- 1.4 m.y. is obtained for samples from rock 72275. A two-stage exposure model is developed to account for this discordance and for the remaining cosmogenic rare-gas data. The first stage was initiated at least 55 m.y. ago, probably as a result of the excavation of the boulder source-crop. A discrete change in shielding depths approx. 35 m.y. ago probably corresponds to the dislodgement of Boulder 1 from the South Massif and emplacement in its present position

  15. Valorization of mud from Fergoug dam in manufacturing mortars

    Directory of Open Access Journals (Sweden)

    L. Laoufi

    2016-12-01

    Full Text Available The production of calcined mud, with pozzolanic properties, from the large quantities of sediments dredged from Algerian dams, could be a good opportunity for the formulation of high performance mortars and pozzolanic concretes, with lower costs and less greenhouse gas (CO2 emissions. The optimal temperatures selected for calcination were 750, 850 and 950 °C. The burning operation was continuous over a period of 3 h. Therefore, a series of physical, chemical, mechanical and microstructural analyses were conducted on sediment samples, collected from the waters of Fergoug dam. The results obtained from the analyses of the calcined mud, from the dam, allowed saying that mortars with different percentages of that mud represent a potential source of high reactivity pozzolanic materials.

  16. Development of novel ash hybrids to introgress resistance to emerald ash borer into north American ash species

    Science.gov (United States)

    Jennifer L. Koch; David W. Carey; Mary E. Mason

    2008-01-01

    Currently, there is no evidence that any of the native North American ash species have any resistance to the emerald ash borer (EAB). This means that the entire ash resource of the eastern United States and Canada is at risk of loss due to EAB. In contrast, outbreaks of EAB in Asian ash species are rare and appear to be isolated responses to stress (Bauer et al. 2005,...

  17. Warts phosphorylates mud to promote pins-mediated mitotic spindle orientation in Drosophila, independent of Yorkie.

    Science.gov (United States)

    Dewey, Evan B; Sanchez, Desiree; Johnston, Christopher A

    2015-11-02

    Multicellular animals have evolved conserved signaling pathways that translate cell polarity cues into mitotic spindle positioning to control the orientation of cell division within complex tissue structures. These oriented cell divisions are essential for the development of cell diversity and the maintenance of tissue homeostasis. Despite intense efforts, the molecular mechanisms that control spindle orientation remain incompletely defined. Here, we describe a role for the Hippo (Hpo) kinase complex in promoting Partner of Inscuteable (Pins)-mediated spindle orientation. Knockdown of Hpo, Salvador (Sav), or Warts (Wts) each result in a partial loss of spindle orientation, a phenotype previously described following loss of the Pins-binding protein Mushroom body defect (Mud). Similar to orthologs spanning yeast to mammals, Wts kinase localizes to mitotic spindle poles, a prominent site of Mud localization. Wts directly phosphorylates Mud in vitro within its C-terminal coiled-coil domain. This Mud coiled-coil domain directly binds the adjacent Pins-binding domain to dampen the Pins/Mud interaction, and Wts-mediated phosphorylation uncouples this intramolecular Mud interaction. Loss of Wts prevents cortical Pins/Mud association without affecting Mud accumulation at spindle poles, suggesting phosphorylation acts as a molecular switch to specifically activate cortical Mud function. Finally, loss of Wts in Drosophila imaginal disc epithelial cells results in diminished cortical Mud and defective planar spindle orientation. Our results provide new insights into the molecular basis for dynamic regulation of the cortical Pins/Mud spindle positioning complex and highlight a novel link with an essential, evolutionarily conserved cell proliferation pathway. Copyright © 2015 Elsevier Ltd. All rights reserved.

  18. Assessing enigmatic boulder deposits in NE Aegean Sea: importance of historical sources as tool to support hydrodynamic equations

    Directory of Open Access Journals (Sweden)

    M. Vacchi

    2012-04-01

    Full Text Available Due to their importance in the assessment of coastal hazards, several studies have focused on geomorphological and sedimentological field evidence of catastrophic wave impacts related to historical tsunami events. Among them, many authors used boulder fields as important indicators of past tsunamis, especially in the Mediterranean Sea. The aim of this study was to understand the mechanism of deposition of clusters of large boulders, consisting of beachrock slabs, which were found on the southern coasts of Lesvos Island (NE Aegean Sea. Methods to infer the origin of boulder deposits (tsunami vs. storm wave are often based on hydrodynamic models even if different environmental complexities are difficult to be incorporated into numerical models. In this study, hydrodynamic equations did not provide unequivocal indication of the mechanism responsible for boulder deposition in the study area. Further analyses, ranging from geomorphologic to seismotectonic data, indicated a tsunami as the most likely cause of displacement of the boulders but still do not allow to totally exclude the extreme storm origin. Additional historical investigations (based on tsunami catalogues, historical photos and aged inhabitants interviews indicated that the boulders are likely to have been deposited by the tsunami triggered by the 6.7 Ms Chios-Karaburum earthquake of 1949 or, alternatively, by minor effects of the destructive tsunami produced by 1956's Amorgos Island earthquake. Results of this study point out that, at Mediterranean scale, to flank numerical models with the huge amount of the available historical data become a crucial tool in terms of prevention policies related to catastrophic coastal events.

  19. Provenance discrimination of sediments in the Zhejiang-Fujian mud belt, East China Sea: Implications for the development of the mud depocenter

    Science.gov (United States)

    Liu, Xiting; Li, Anchun; Dong, Jiang; Lu, Jian; Huang, Jie; Wan, Shiming

    2018-01-01

    In the past decade, the 800 km elongated mud belt off Zhejiang-Fujian coast, East China Sea (ECS), has been extensively studied for understanding the source to sink processes on the East Asian continental margin in the context of the Asian monsoon. However, to better understand the sediment source and dispersal pattern, the existing mineralogical and geochemical data of adjacent river systems, including the Changjiang River (CJR) and local rivers in Zhejiang, Fujian and Taiwan, need to be systematically reviewed. Therefore, various indicators from published literatures for the provenance discrimination in the mud belt have been summarised in this article. The results show that high diversity of clay mineral assemblages in fluvial sediments being supplied into the mud belt, e.g., dominant illite and chlorite in the CJR, absence of smectite in Taiwan rivers, similar amounts of the four clay mineral species in Zhejiang rivers, and dominant kaolinite in Fujian rivers. On heavy mineralogy, the CJR is dominated by dolomite, hornblende, and flaky minerals; and among of them, dolomite is distinctive for the CJR. For geochemical approaches, elemental compositions, combined with strontium and neodymium isotopes, reflect strong provenance control. However, geochemical and mineralogical compositions are found to vary with grain size, and thus extra caution should be taken when using these parameters as provenance indicator to discriminate the marine sediments with variety of grain-size fractions. In addition, pyrrhotite, occurred in fluvial sediments from western Taiwan, has not been found in sediments derived from mainland China, indicating that magnetic parameters could be used to discriminate sediment provenance. The mud belt formed during sea-level highstand, when modern current system in the ECS has been established, resulting in sediments derived from the CJR have been transported southward since 8 ka. In addition, sediment provenances have not been constant since

  20. Mud Pit Risk-Based Closure Strategy Report, Nevada Test Site, Nevada, Revision 0

    Energy Technology Data Exchange (ETDEWEB)

    Brain Hoenes

    2004-08-01

    This report presents the findings of the human and ecological risk assessment for the NTS mud pits. The risk assessment utilizes data from 52 of the 270 NTS mud pits in conjunction with corroborative data from 87 other DOE mud pits associated with nuclear testing (at locations on the NTS, in the western United States, and Alaska) as well as relevant process knowledge. Based on the risk assessment findings, the report provides a strategy for further evaluation, characterization, and closure of all 270 NTS mud pit CASs using the Streamlined Approach for Environmental Restoration (SAFER).

  1. Implementation of viscoelastic mud-induced energy attenuation in the third-generation wave model, SWAN

    Science.gov (United States)

    Beyramzade, Mostafa; Siadatmousavi, Seyed Mostafa

    2018-01-01

    The interaction of waves with fluid mud can dissipate the wave energy significantly over few wavelengths. In this study, the third-generation wave model, SWAN, was advanced to include attenuation of wave energy due to interaction with a viscoelastic fluid mud layer. The performances of implemented viscoelastic models were verified against an analytical solution and viscous formulations for simple one-dimensional propagation cases. Stationary and non-stationary test cases in the Surinam coast and the Atchafalaya Shelf showed that the inclusion of the mud-wave interaction term in the third-generation wave model enhances the model performance in real applications. A high value of mud viscosity (of the order of 0.1 m2/s) was required in both field cases to remedy model overestimation at high frequency ranges of the wave spectrum. The use of frequency-dependent mud viscosity value improved the performance of model, especially in the frequency range of 0.2-0.35 Hz in the wave spectrum. In addition, the mud-wave interaction might affect the high frequency part of the spectrum, and this part of the wave spectrum is also affected by energy transfer from wind to waves, even for the fetch lengths of the order of 10 km. It is shown that exclusion of the wind input term in such cases might result in different values for parameters of mud layer when inverse modeling procedure was employed. Unlike viscous models for wave-mud interaction, the inverse modeling results to a set of mud parameters with the same performance when the viscoelastic model is used. It provides an opportunity to select realistic mud parameters which are in more agreement with in situ measurements.

  2. Silica from Ash

    Indian Academy of Sciences (India)

    management, polymer composites and chemical process design. Figure 1 Difference in color of the ash ... The selection of ash is important as the quality of ash determines the total amount as well as quality of silica recoverable Ash which has undergone maximum extent of combustion is highly desirable as it contains ...

  3. Rheological measurements on artifical muds

    NARCIS (Netherlands)

    De Wit, P.J.

    1992-01-01

    The rheological behaviour of three artificial muds was determined using a rotational viscometer. First some characteristics of the viscometer used were rneasured. For want of an appropriate calibration tluid, the viscosity of demineralized water was determined. The result agreed very well with what

  4. Morphodynamic Modeling of Tidal Mud Flats

    National Research Council Canada - National Science Library

    Winterwerp, Johan C

    2008-01-01

    The objective of the current research proposal is to develop and test a numerical model to simulate and predict the seasonal morphodynamic evolution of intertidal mud flats in macrotidal environments...

  5. Effect of strong acids on red mud structural and fluoride adsorption properties.

    Science.gov (United States)

    Liang, Wentao; Couperthwaite, Sara J; Kaur, Gurkiran; Yan, Cheng; Johnstone, Dean W; Millar, Graeme J

    2014-06-01

    The removal of fluoride using red mud has been improved by acidifying red mud with hydrochloric, nitric and sulphuric acid. The acidification of red mud causes sodalite and cancrinite phases to dissociate, confirmed by the release of sodium and aluminium into solution as well as the disappearance of sodalite bands and peaks in infrared and X-ray diffraction data. The dissolution of these mineral phases increases the amount of available iron and aluminium oxide/hydroxide sites that are accessible for the adsorption of fluoride. However, concentrated acids have a negative effect on adsorption due to the dissolution of these iron and aluminium oxide/hydroxide sites. The removal of fluoride is dependent on the charge of iron and aluminium oxide/hydroxides on the surface of red mud. Acidifying red mud with hydrochloric, nitric and sulphuric acid resulted in surface sites of the form ≡SOH2(+) and ≡SOH. Optimum removal is obtained when the majority of surface sites are in the form ≡SOH2(+) as the substitution of a fluoride ion does not cause a significant increase in pH. This investigation shows the importance of having a low and consistent pH for the removal of fluoride from aqueous solutions using red mud. Copyright © 2014 Elsevier Inc. All rights reserved.

  6. False deformation temperatures for ash fusibility associated with the conditions for ash preparation

    Energy Technology Data Exchange (ETDEWEB)

    Wall, T.F.; Gupta, S.K.; Gupta, R.P.; Sanders, R.H.; Creelman, R.A.; Bryant, G.W. [University of Newcastle, Callaghan, NSW (Australia). Cooperative Research Centre for Black Coal Utilization, Dept. of Chemical Engineering

    1999-07-01

    A study was made to investigate the fusibility behaviour of coal ashes of high ash fusion temperatures. Coals and ashes formed in the boiler were sampled in several Australian power stations, with laboratory ashes being prepared from the coals. The laboratory ashes gave lower values for the deformation temperature (DT) than the combustion ashes when the ash had low levels of basic oxide components. Thermo-mechanical analysis, quantitative X-ray diffraction and scanning electron microscopy were used to establish the mechanisms responsible for the difference. Laboratory ash is finer than combustion ash and it includes unreacted minerals (such as quartz, kaolinite and illite) and anhydrite (CaSO{sub 4}). Fusion events which appear to be characteristic of reacting illite, at temperatures from 900 to 1200{degree}C, were observed for the laboratory ashes, these being associated with the formation of melt phase and substantial shrinkage. The combustion ashes did not contain this mineral and their fusion events were observed at temperatures exceeding 1300{degree}C. The low DTs of coal ashes with low levels of basic oxides are therefore a characteristic of laboratory ash rather than that found in practical combustion systems. These low temperatures are not expected to be associated with slagging in pulverised coal fired systems. 10 refs., 3 figs., 2 tabs.

  7. Electrical resistivity and rheological properties of sensing bentonite drilling muds modified with lightweight polymer

    Directory of Open Access Journals (Sweden)

    Ahmed S. Mohammed

    2018-03-01

    Full Text Available In this study, the electrical resistivity and rheological properties of a water-based bentonite clay drilling mud modified with the lightweight polymer (guar gum under various temperature were investigated. Based on the experimental and analytical study, the electrical resistivity was identified as the sensing property of the bentonite drilling mud so that the changes in the properties can be monitored in real-time during the construction. The bentonite contents in the drilling muds were varied up to 8% by the weight of water and temperature was varied from 25 °C to 85 °C. The guar gum content (GG% was varied between 0% and 1% by the weight of the drilling mud to modify the rheological properties and enhance the sensing electrical resistivity of the drilling mud. The guar gum and bentonite clay were characterized using thermal gravimetric analysis (TGA. The total weight loss at 800 °C for the bentonite decreased from 12.96% to 0.7%, about 95% reduction, when the bentonite was mixed with 1% of guar gum. The results also showed that 1% guar gum decreased the electrical resistivity of the drilling mud from 50% to 90% based on the bentonite content and the temperature of the drilling mud. The guar gum modification increased the yield point (YP and plastic viscosity (PV by 58% to 230% and 44% to 77% respectively based on the bentonite content and temperature of the drilling mud. The rheological properties of the drilling muds have been correlated to the electrical resistivity of the drilling mud using nonlinear power and hyperbolic relationships. The model predictions agreed well with the experimental results. Hence the performance of the bentonite drilling muds with and without guar gum can be characterized based on the electrical resistivity which can be monitored real-time in the field. Keywords: Bentonite, Polymer (Guar gum, Electrical resistivity, Rheological properties, Temperature, Modeling

  8. Analysis of chloride diffusivity in concrete containing red mud

    Directory of Open Access Journals (Sweden)

    D.V. Ribeiro

    Full Text Available Red mud is a solid waste produced in the alumina production process and, due to its high pH, is classified as hazardous. Its incorporation in concrete mixtures, acting as filler due to the particles fineness, might be an interesting reuse alternative. The focus of this paper is to study the chloride diffusivity of concrete mixtures containing red-mud. The concentration of chlorides was monitored by measuring the conductivity of the anolyte, which was distilled water initially. In addition, the estimation of the chloride ions diffusion coefficients in steady and non-steady conditions, Ds and Dns, was obtained from the ''time-lag'' and ''equivalent time'' between diffusion and migration experiments. Due to superfine particle-size distribution and the "filler" effect, the red mud addition seems to assure lower chloride diffusivity.

  9. A Comparative SEM-EDS Elemental Composition of Mud in Coastal ...

    African Journals Online (AJOL)

    The present study was aimed to understand the comparative abundance and source of elemental constituents in mud of four coastal shrimp farming areas, Vunh Tau (VT), Nha Trang (NT), Da Nang (DN) and Hue (HU) in Viet Nam using SEM-EDS analysis. Mud samples were collected from shrimp farming coastal zones ...

  10. Use of clay-free polymer saline drilling muds. Primeneniye bezglinistykh polimerosolevykh burovykh rastvorov

    Energy Technology Data Exchange (ETDEWEB)

    Krysin, N I; Ishmukhametova, A M; Krysina, T I; Mavlyutov, M R

    1982-01-01

    A brief analysis is made of the geological and technical and technological conditions for drilling and stripping productive beds in the Perm Prikamye. Domestic and foreign experience in the area of studies covering the effect of properties of the drilling muds on the indicators of operation of bits and preservation of stability of the well shaft walls, as well as for development of formulas for clay-free drilling muds is generalized. Results are presented of studies on viscosity and filtering properties of drilling muds, development of clay-free drilling muds based on potassium containing wastes and bed waters.

  11. Mud Banks along the southwest coast of India are not too muddy for plankton.

    Science.gov (United States)

    Jyothibabu, R; Balachandran, K K; Jagadeesan, L; Karnan, C; Arunpandi, N; Naqvi, S W A; Pandiyarajan, R S

    2018-02-07

    Considering Alappuzha Mud Bank in the southern Kerala coast as a typical case of biologically productive Mud Banks that form along the southwest coast of India during the Southwest Monsoon (June - September), the present study addresses several pertinent missing links between the physical environment in Mud Banks and their influence on plankton stock. This study showed that very strong coastal upwelling prevails in the entire study domain during the Southwest Monsoon, which manifests itself in the form of significantly cool, hypoxic and nitrate-rich waters surfacing near the coast. The upwelled water persisting throughout the Southwest Monsoon period was found to have fuelled the exceptionally high phytoplankton stock in the entire study area, including the Mud Bank region. Having accepted that Mud Banks are special because of the calm sea surface conditions and relatively high turbidity level in the water column around them, the present study showed that except at points close to the sea bottom, turbidity level in the Alappuzha Mud Bank was below the critical level to inhibit the plankton stock. The suspended sediments that form in the Mud Bank occasionally could be attributed to the disturbance of the bottom fluid muddy layer and their vertical spurts.

  12. Propagation of Measurement-While-Drilling Mud Pulse during High Temperature Deep Well Drilling Operations

    Directory of Open Access Journals (Sweden)

    Hongtao Li

    2013-01-01

    Full Text Available Signal attenuates while Measurement-While-Drilling (MWD mud pulse is transmited in drill string during high temperature deep well drilling. In this work, an analytical model for the propagation of mud pulse was presented. The model consists of continuity, momentum, and state equations with analytical solutions based on the linear perturbation analysis. The model can predict the wave speed and attenuation coefficient of mud pulse. The calculated results were compared with the experimental data showing a good agreement. Effects of the angular frequency, static velocity, mud viscosity, and mud density behavior on speed and attenuation coefficients were included in this paper. Simulated results indicate that the effects of angular frequency, static velocity, and mud viscosity are important, and lower frequency, viscosity, and static velocity benefit the transmission of mud pulse. Influenced by density behavior, the speed and attenuation coefficients in drill string are seen to have different values with respect to well depth. For different circulation times, the profiles of speed and attenuation coefficients behave distinctly different especially in lower section. In general, the effects of variables above on speed are seen to be small in comparison.

  13. Plugging wellbore fractures : limit equilibrium of a Bingham drilling mud cake in a tensile crack

    Energy Technology Data Exchange (ETDEWEB)

    Garagash, D.I. [Dalhousie Univ., Halifax, NS (Canada). Dept. of Civil and Resource Engineering

    2009-07-01

    The proper selection of drilling muds is important in order to successfully drill hydrocarbon wells in which wellbore mud pressure remains low enough to prevent circulation loss and high enough to support the uncased wellbore against the shear failure. This paper presented a mathematical model to study invasion of mud cake into a drilling-induced planar fracture at the edge of a wellbore perpendicular to the minimum in situ principal stress. The model assumed a planar edge-crack geometry loaded by the wellbore hoop stress, variable mud pressure along the invaded region adjacent to the wellbore, and uniform pore-fluid pressure along the rest of the crack. The invading mud was assumed to freely displaces the pore-fluid in the crack without mixing with it. The case corresponding to a sufficiently permeable formation was considered. This solution provides a means to evaluate whether or not the mud cake could effectively plug the fracture, thereby prevent fracture propagation and associated uncontrollable loss of wellbore drilling mud. The toughness or tensile strength is evaluated based on criterion for initiation of crack propagation, which may lead to uncontrollable loss of mud circulation in a well. The study provided information on the breakdown pressure as a function of the rock ambient stress, ambient pore pressure, pre-existing crack length, and mud cake properties. 12 refs., 6 figs.

  14. Cementing Efficiency of Low Calcium Fly Ash in Fly Ash Concretes

    OpenAIRE

    T. D. Gunneswara Rao; Mudimby Andal

    2014-01-01

    Research on the utilization of fly ash will no longer refer the fly ash as a waste material of thermal power plants. Use of fly ash in concrete making, makes the concrete economical as well as durable. The fly ash is being added to the concrete in three ways namely, as partial replacement to cement, as partial replacement to fine aggregates and as admixture. Addition of fly ash to the concrete in any one of the form mentioned above, makes the concrete more workable and durable than the conven...

  15. INTEGRATED DRILLING SYSTEM USING MUD ACTUATED DOWN HOLE HAMMER AS PRIMARY ENGINE

    Energy Technology Data Exchange (ETDEWEB)

    John V. Fernandez; David S. Pixton

    2005-12-01

    A history and project summary of the development of an integrated drilling system using a mud-actuated down-hole hammer as its primary engine are given. The summary includes laboratory test results, including atmospheric tests of component parts and simulated borehole tests of the hammer system. Several remaining technical hurdles are enumerated. A brief explanation of commercialization potential is included. The primary conclusion for this work is that a mud actuated hammer can yield substantial improvements to drilling rate in overbalanced, hard rock formations. A secondary conclusion is that the down-hole mud actuated hammer can serve to provide other useful down-hole functions including generation of high pressure mud jets, generation of seismic and sonic signals, and generation of diagnostic information based on hammer velocity profiles.

  16. Titanium leaching from red mud by diluted sulfuric acid at atmospheric pressure

    International Nuclear Information System (INIS)

    Agatzini-Leonardou, S.; Oustadakis, P.; Tsakiridis, P.E.; Markopoulos, Ch.

    2008-01-01

    Laboratory-scale research has focused on the recovery of titanium from red mud, which is obtained from bauxite during the Bayer process for alumina production. The leaching process is based on the extraction of this element with diluted sulfuric acid from red mud under atmospheric conditions and without using any preliminary treatment. Statistical design and analysis of experiments were used, in order to determine the main effects and interactions of the leaching process factors, which were: acid normality, temperature and solid to liquid ratio. The titanium recovery efficiency on the basis of red mud weight reached 64.5%. The characterization of the initial red mud, as well as this of the leached residues was carried out by X-ray diffraction, TG-DTA and scanning electron microscopy

  17. Emerald ash borer biocontrol in ash saplings: the potential for early stage recovery of North American ash

    Science.gov (United States)

    In many parts of North America, ash stands have been reduced by the emerald ash borer (Agrilus planipennis) invasion to a few surviving mature trees and young basal sprouts, saplings, and seedlings. Without a seed bank, ash tree recovery will require survival and maturation of these younger cohorts...

  18. Radioactivity of wood ash

    International Nuclear Information System (INIS)

    Rantavaara, A.; Moring, M.

    2000-01-01

    STUK (Finnish Radiation and Nuclear Safety Authority) has investigated natural and artificial radioactivity in wood ash and radiation exposure from radionuclides in ash since 1996. The aim was to consider both handling of ash and different ways of using ash. In all 87 ash samples were collected from 22 plants using entirely or partially wood for their energy production in 1996-1997. The sites studied represented mostly chemical forest industry, sawmills or district heat production. Most plants used fluidised bed combustion technique. Samples of both fly ash and bottom ash were studied. The activity concentrations of radionuclides in samples of, e.g., dried fly ash from fuel containing more than 80% wood were determined. The means ranged from 2000 to less than 50 Bq kg -1 , in decreasing order: 137 Cs, 40 K, 90 Sr, 210 Pb, 226 Ra, 232 Th, 134 Cs, 235 U. In bott radionuclide contents decreased in the same order as in fly ash, but were smaller, and 210 Pb was hardly detectable. The NH 4 Ac extractable fractions of activities for isotopes of alkaline elements (K, Cs) in bottom ash were lower than in fly ash, whereas solubility of heavier isotopes was low. Safety requirements defined by STUK in ST-guide 12.2 for handling of peat ash were fulfilled at each of the sites. Use of ash for land-filling and construction of streets was minimal during the sampling period. Increasing this type of ash use had often needed further investigations, as description of the use of additional materials that attenuate radiation. Fertilisation of forests with wood ash adds slightly to the external irradiation in forests, but will mostly decrease doses received through use of timber, berries, mushrooms and game meat. (orig.)

  19. Recovery of rare earths from red mud

    International Nuclear Information System (INIS)

    Bautista, R.G.

    1992-01-01

    The prospect for the recovery of rare earths from red mud, the bauxite tailings from the production of alumina is examined. The Jamaican red mud by far has the higher trace concentrations of lanthanum, cerium, neodymium, and yttrium. Scandium is also present. The dissolution of the rare earth is a major extraction problem because of the large volume of other materials. The recovery processes that have been proposed include the production of co-products such as iron, alumina, and titanium concentrates, with the rare earths going with the titanium. In this paper a critical examination of the possible processes are presented with the recommended research projects to be carried out

  20. Method of preparing light-weight plugging mud

    Energy Technology Data Exchange (ETDEWEB)

    Gorskiy, V F; Melnichuk, A N; Vernikovskiy, A N

    1982-01-01

    A method is proposed for preparing a light-weight plugging mud which includes mixing Portland cement on an aqueous suspension of palygorskite. It is distinguished by the fact that in order to improve the quality of the mud and strength of the cement stone with simultaneous decrease in the gas permeability, before mixing the Portland cement, the aqueous suspension of palygorskite is dispersed to stabilization of viscosity, and after mixing the Portland cement, the obtained cement-clay mixture is exposed to additional dispersion under pressure. The ratio of the ingredients is the following (% by mass): Portland cement 32.0-61.0; palygorskite 1.2-2.9; water--the rest.

  1. Additive to clay drilling muds

    Energy Technology Data Exchange (ETDEWEB)

    Voytenko, V.S.; Nekrasova, V.B.; Nikitinskiy, E.L.; Ponomarev, V.N.

    1984-01-01

    The purpose of the invention is to improve the lubricating and strengthening properties of clay drilling muds. This goal is achieved because the lubricating and strengthening additive used is waste from the pulp and paper industry at the stage of reprocessing crude sulfate soap into phytosterol.

  2. Time-dependent source model of the Lusi mud volcano

    Science.gov (United States)

    Shirzaei, M.; Rudolph, M. L.; Manga, M.

    2014-12-01

    The Lusi mud eruption, near Sidoarjo, East Java, Indonesia, began erupting in May 2006 and continues to erupt today. Previous analyses of surface deformation data suggested an exponential decay of the pressure in the mud source, but did not constrain the geometry and evolution of the source(s) from which the erupting mud and fluids ascend. To understand the spatiotemporal evolution of the mud and fluid sources, we apply a time-dependent inversion scheme to a densely populated InSAR time series of the surface deformation at Lusi. The SAR data set includes 50 images acquired on 3 overlapping tracks of the ALOS L-band satellite between May 2006 and April 2011. Following multitemporal analysis of this data set, the obtained surface deformation time series is inverted in a time-dependent framework to solve for the volume changes of distributed point sources in the subsurface. The volume change distribution resulting from this modeling scheme shows two zones of high volume change underneath Lusi at 0.5-1.5 km and 4-5.5km depth as well as another shallow zone, 7 km to the west of Lusi and underneath the Wunut gas field. The cumulative volume change within the shallow source beneath Lusi is ~2-4 times larger than that of the deep source, whilst the ratio of the Lusi shallow source volume change to that of Wunut gas field is ~1. This observation and model suggest that the Lusi shallow source played a key role in eruption process and mud supply, but that additional fluids do ascend from depths >4 km on eruptive timescales.

  3. Radiological aspects of the usability of red mud as building material additive

    International Nuclear Information System (INIS)

    Somlai, Janos; Jobbagy, Viktor; Kovacs, Jozsef; Tarjan, Sandor; Kovacs, Tibor

    2008-01-01

    Several researchers have examined and achieved favourable results in connection with the building industry's use of red mud extracted in large quantities from the processing of bauxite. These days more and more precedence is being given to limiting the radiological dose to the population. In this study carried out in Hungary, the use of red mud, bauxite, and clay additives recommended for the production of special cements, were examined from a radiological aspect. 226 Ra and 232 Th activity concentrations measured in Hungarian bauxite, red mud and clay samples were significantly similar with the levels for such raw materials mentioned in international literature. Taking radiation protection aspects into consideration, none of these products can be directly used for building construction. Taking Hungarian and international values into consideration, a small amount of red mud, not exceeding 15% could be used for brick production, for example as a colouring material. However, beyond this amount the standards for building materials would not be met. For the production of cements an even stricter limit needs to be determined when both bauxite and red mud are used

  4. Source Signature of Sr Isotopes in Fluids Emitting From Mud volcanoes in Taiwan

    Science.gov (United States)

    Chung, C.; You, C.; Chao, H.

    2003-12-01

    Located at the boundary between the Philippine Sea Plate and the Asia Continental Plate, abundance of mud volcanoes were erupted on land in Taiwan. According to their occurrences and associated tectonic settings, these mud volcanoes were classified into four groupies. The group (I) mud volcanoes are located in the western coastal plane, whereas group (II) and (III) are situated near the Kutinkung anticline axis and the Chishan fault respectively. The group (IV) mud volcanoes are discovered at the Coastal Range. Although there are numerous studies focused on morphology, possible fluid migration paths and sources are poorly understood. We have collected and analyzed major ions and Sr isotopic ratios in fluids separated from various mud volcanoes in Taiwan. Chemical contents of these fluids were measured by IC and the emitted gasses were analyzed by GC. The Sr concentrations in these fluids were determined using AA and the isotopic compositions were analyzed by TIMS. The dominated ions in fluids are Na and Cl which account for 98% of dissolved materials. All fluids show similar Na/Cl ratios(0.7-0.8), slightly higher than seawater but each group has unique Sr isotopic signature. Waters expelled from group I mud volcanoes featured with low salinity and high Sr isotopic ratios ranged from 0.71150 to 0.71175. Groups II and III were outcroped in the Kutinkung formation but show distinctive chemical compositions. Group II fluids have four times Cl concentrations(358-522mM) compared with those of group III(85-162mM). The latter fluids appear to be more radiogenic(0.71012- 0.71075) indicating possible influence due to water-rock interactions. Low 87Sr/86Sr(0.70692-0.70939) is typical characteristic of mud volcano fluids in group IV where large Mg and K depletion were discovered, suggesting effects due to sediment diagenetic processes. The chemical compositions of mud volcano associated gasses show similar distribution pattern. The major gas constituents in mud volcano zones

  5. 78 FR 20168 - Notice of Intent To Rule on Request To Release Airport Property at the Boulder Municipal Airport...

    Science.gov (United States)

    2013-04-03

    ... To Release Airport Property at the Boulder Municipal Airport, Boulder, CO AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Notice of request to release airport property. SUMMARY: The FAA proposes to... of Section 125 of the Wendell H. Ford Aviation Investment Reform Act for the 21st Century (AIR 21...

  6. Viral infections stimulate the metabolism and shape prokaryotic assemblages in submarine mud volcanoes.

    Science.gov (United States)

    Corinaldesi, Cinzia; Dell'Anno, Antonio; Danovaro, Roberto

    2012-06-01

    Mud volcanoes are geological structures in the oceans that have key roles in the functioning of the global ecosystem. Information on the dynamics of benthic viruses and their interactions with prokaryotes in mud volcano ecosystems is still completely lacking. We investigated the impact of viral infection on the mortality and assemblage structure of benthic prokaryotes of five mud volcanoes in the Mediterranean Sea. Mud volcano sediments promote high rates of viral production (1.65-7.89 × 10(9) viruses g(-1) d(-1)), viral-induced prokaryotic mortality (VIPM) (33% cells killed per day) and heterotrophic prokaryotic production (3.0-8.3 μgC g(-1) d(-1)) when compared with sediments outside the mud volcano area. The viral shunt (that is, the microbial biomass converted into dissolved organic matter as a result of viral infection, and thus diverted away from higher trophic levels) provides 49 mgC m(-2) d(-1), thus fuelling the metabolism of uninfected prokaryotes and contributing to the total C budget. Bacteria are the dominant components of prokaryotic assemblages in surface sediments of mud volcanoes, whereas archaea dominate the subsurface sediment layers. Multivariate multiple regression analyses show that prokaryotic assemblage composition is not only dependant on the geochemical features and processes of mud volcano ecosystems but also on synergistic interactions between bottom-up (that is, trophic resources) and top-down (that is, VIPM) controlling factors. Overall, these findings highlight the significant role of the viral shunt in sustaining the metabolism of prokaryotes and shaping their assemblage structure in mud volcano sediments, and they provide new clues for our understanding of the functioning of cold-seep ecosystems.

  7. Mud peeling and horizontal crack formation in drying clays

    KAUST Repository

    Style, Robert W.

    2011-03-01

    Mud peeling is a common phenomenon whereby horizontal cracks propagate parallel to the surface of a drying clay. Differential stresses then cause the layer of clay above the crack to curl up to form a mud peel. By treating the clay as a poroelastic solid, we analyze the peeling phenomenon and show that it is caused by the gradient in tensile stress at the surface of the clay, analogously to the spalling of thermoelastic materials. For a constant water evaporation rate at the clay surface we derive equations for the depth of peeling and the time of peeling as functions of the evaporation rate. Our model predicts a simple relationship between the radius of curvature of a mud peel and the depth of peeling. The model predictions are in agreement with the available experimental data. Copyright 2011 by the American Geophysical Union.

  8. Comparative toxicity of offshore and oil-added drilling muds to larvae of the grass shrimp Palaemonetes intermedius

    Energy Technology Data Exchange (ETDEWEB)

    Conklin, P.J.; Rao, K.R.

    1984-11-01

    Offshore drilling fluids (muds) varied widely in their toxicity to grass shrimp (Palaemonetes intermedius) larvae. The 96-h LC/sub 50/s for the eleven drilling muds tested ranged from 142 to > 100,000 ppM (..mu..l/L). There was a significant correlation between oil content of the drilling muds and their toxicity. Furthermore, addition of diesel oil (No. 2 fuel oil) or mineral oil to an offshore drilling mud having a low oil content or to an oil-free synthetic drilling mud led to a marked increase in the toxicity of these muds. Thus, much of the toxicity of the offshore drilling muds tested can be attributable to the oil content. 24 references, 2 figures, 3 tables.

  9. Geochemical recovery of the Torna-Marcal river system after the Ajka red mud spill, Hungary.

    Science.gov (United States)

    Anton, Á D; Klebercz, O; Magyar, Á; Burke, I T; Jarvis, A P; Gruiz, K; Mayes, W M

    2014-12-01

    The failure of the Ajka red mud depository in October 2010 led to the largest single release of red mud into the surface water environment. This study provides a comparative assessment of stream sediment quality in the Torna-Marcal-Rába catchment between post-disaster surveys (2010) and follow up surveys at an identical suite of 21 locations in 2013. The signature of red mud apparent in initial surveys with high Al, As, Cr, Na, V was only apparent at a small number of sample stations in recent surveys. These constitute 20 km reach of affected sediments in the immediate aftermath of the spill. Concentrations of red mud-derived contaminants are predominately associated with fine fractions of the red mud (mud-derived contaminants and, along with extensive remedial efforts, has substantially limited the within-channel inventory of potentially ecotoxic metals and metalloids.

  10. Comparing the efficacy of mature mud pack and hot pack treatments for knee osteoarthritis.

    Science.gov (United States)

    Sarsan, Ayşe; Akkaya, Nuray; Ozgen, Merih; Yildiz, Necmettin; Atalay, Nilgun Simsir; Ardic, Fusun

    2012-01-01

    The objective of this study is to compare the efficacy of mature mud pack and hot pack therapies on patients with knee osteoarthritis. This study was designed as a prospective, randomized-controlled, and single-blinded clinical trial. Twenty-seven patients with clinical and radiologic evidence of knee osteoarthritis were randomly assigned into two groups and were treated with mature mud packs (n 15) or hot packs (n=12). Patients were evaluated for pain [based on the visual analog scale (VAS)], function (WOMAC, 6 min walking distance), quality of life [Short Form-36 (SF-36)], and serum levels of tumor necrosis factor-alpha (TNF-α), interleukin-6 (IL-6), and insulin-like growth factor-1 (IGF-1) at baseline, post-treatment, and 3 and 6~months after treatment. The mud pack group shows a significant improvement in VAS, pain, stifness, and physical function domains of WOMAC. The difference between groups of pain and physical activity domains is significant at post-treatment in favor of mud pack. For a 6 min walking distance, mud pack shows significant improvement, and the difference is significant between groups in favor of mud pack at post-treatment and 3 and 6 months after treatment. Mud pack shows significant improvement in the pain subscale of SF-36 at the third month continuing until the sixth month after the treatment. Significant improvements are found for the social function, vitality/energy, physical role disability, and general health subscales of SF-36 in favor of the mud pack compared with the hot pack group at post-treatment. A significant increase is detected for IGF-1 in the mud pack group 3 months after treatment compared with the baseline, and the difference is significant between groups 3 months after the treatment. Mud pack is a favorable option compared with hotpack for pain relief and for the improvement of functional conditions in treating patients with knee osteoarthritis.

  11. Red mud application in construction industry: review of benefits and possibilities

    Science.gov (United States)

    Lima, M. S. S.; Thives, L. P.; Haritonovs, V.; Bajars, K.

    2017-10-01

    Red mud is a waste originated in the processing of bauxite into aluminium, which properties of high alkalinity make it cumulatively stored, occupying increasing deforested areas. Annually, it is estimated that approximately 117 million tons of red mud are generated in the world, with no prospect of use, what represents an imminent risk of pollution prone to contamination. Nevertheless, environmental liabilities caused by red mud affect not only the environment, but also the companies responsible for the waste, which will be subject to highest fee payments. Although there are studies that prove the feasibility of using this solid waste in the constitution of ceramic materials, there are no large-scale applications. This study seeks to evaluate the possibilities of red mud application in construction industry, focusing into two main areas: cement production/ceramic material and road construction. Backgrounds from other researchers were taken into consideration and analysed according environmental, economic and technical feasibilities.

  12. A novel approach in red mud neutralization using cow dung.

    Science.gov (United States)

    Patel, Sucharita; Pal, Bhatu Kumar; Patel, Raj Kishore

    2018-05-01

    In this study, cow dung was identified as a neutralizing agent for red mud (RM). Present research estimated a significant reduction in pH value of red mud (10 g) from 10.28 to 8.15 and reduction in alkalinity of ~148 mg/L from ~488 mg/L by adding 80 g of cow dung in 40 days of anaerobic condition. XRD results exhibit a high intensity of quartz and found new compound, the calcium carbide. The acid neutralizing capacity (ANC) of NRM reduces to ~0.87 from ~1.506 mol H + /kg. Based on the resultant research, present study proposes cow dung as an efficient neutralizing agent for reducing the pH and alkalinity in the red mud.

  13. Moraine preservation and boulder erosion in the tropical Andes: interpreting old surface exposure ages in glaciated valleys

    Science.gov (United States)

    Smith, Jacqueline A.; Finkel, Robert C.; Farber, Daniel L.; Rodbell, Donald T.; Seltzer, Geoffrey O.

    2005-10-01

    Cosmogenic dating provides a long-awaited means of directly dating glacial deposits that pre-date the last glacial cycle. Although the potential benefits of longer chronologies are obvious, the greater uncertainty associated with older cosmogenic ages may be less readily apparent. We illustrate the challenges of developing and interpreting a long chronology using our data from the Peruvian Andes. We used surface exposure dating with cosmogenic radionuclides (CRNs; 10Be and 26Al) to date 140 boulders on moraines in valleys bordering the Junin Plain (11° S, 76° W) in central Peru. Our chronology spans multiple glacial cycles and includes exposure ages greater than 1 million years, which indicate that long-term rates of boulder erosion have been very low. Interpreting the chronology of moraines for glaciations that predate the last glacial cycle is complicated by the need to consider boulder erosion and exhumation, surface uplift, and inheritance of CRNs from previous exposure intervals. As an example, we recalculate exposure ages using our boulder erosion rates (0.3-0.5 metres per million years) and estimated surface uplift rates to emphasise both the challenges involved in interpreting old surface exposure ages and the value of chronological data, even with large uncertainties, when reconstructing the palaeoclimate of a region.

  14. The condition and ways to develop operations to establish standards for drilling muds in the ''Grozneft''' Union

    Energy Technology Data Exchange (ETDEWEB)

    Baranov, V S; Volkova, A P

    1979-01-01

    Four intervals are strictly defined in the geological section of the sites of ''Grozneft''', which require the use of different types of drilling muds (R). The upper part of the section to the Karagano-Chokraksk sediments inclusively should be drilled with wash through by limestone clay mud, whose use should begin immediately after the lowering of the conducter. The upper Maykop sediments should be drilled with the use of a weighted limestone mud, strictly observing the concentration of the lime and the caustic soda in the mud. In the deposits of the lower Maykop, where the temperature reaches 120/sup 0/C, a gypsum and clay mud should be used, using oxyl for regulating its viscosity. In the deposits of the Upper Cretaceous, for which absorption is characteristic, it is expedient to wash through with water or clay mud, processed by UShchR and bichromate. The deposits of the lower Cretaceous should be drilled with wash through by a gypsum mud, processed by lignosulfonates, where it is recommended to use KSSB-4. The capability is assumed of using chlorocalcium clay mud in drilling the Maykop clays. A condition for the effective use of any types of drilling muds is the improved system for removing drilled out rock from the mud.

  15. Effect of self-glazing on reducing the radioactivity levels of red mud based ceramic materials

    Energy Technology Data Exchange (ETDEWEB)

    Qin, Shuo [College of Material Science and Engineering, Guilin University of Technology, Guilin, Guangxi 541004 (China); Wu, Bolin, E-mail: wubolin3211@gmail.com [College of Material Science and Engineering, Guilin University of Technology, Guilin, Guangxi 541004 (China)

    2011-12-30

    Graphical abstract: Self-glazing red mud based ceramic materials (RMCM) were produced by normal pressure sintering process using the main raw materials of red mud. The properties of the RMCM samples were investigated by the measurements of mechanical properties, radiation measurement, X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that the self-glazing RMCM have good mechanical properties (water absorption and apparent porosity approached zero; bulk density, 2.94 g/cm{sup 3}; compressive strength, 78.12 MPa). The radiation level has clear change regularity that the radioactivity levels of red mud (6360 Bq) are obvious declined, and can be reduced to that of the natural radioactive background of Guilin Karst landform, China (3600 Bq). It will not only consume large quantities of red mud, but also decrease the production cost of self-glazing RMCM. And the statement of this paper will offer effective ways to reduce the radioactivity level of red mud. Highlights: Black-Right-Pointing-Pointer The self-glazing phenomenon in red mud system was first discovered in our research. Black-Right-Pointing-Pointer Radiation levels of red mud can be reduced efficiently by self-glazing layer. Black-Right-Pointing-Pointer Red mud based ceramic materials will not cause harm to environment and humans. Black-Right-Pointing-Pointer This research possesses important economic significances to aluminum companies. - Abstract: Self-glazing red mud based ceramic materials (RMCM) were produced by normal pressure sintering process using the main raw materials of red mud. The properties of the RMCM samples were investigated by the measurements of mechanical properties, radiation measurement, X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that the self-glazing RMCM have good mechanical properties (water absorption and apparent porosity approached zero; bulk density, 2.94 g/cm{sup 3}; compressive strength, 78.12 MPa). The radiation

  16. Sensory Characteristics of Mud Clam (Polymesoda Erosa) Hydrolysate

    International Nuclear Information System (INIS)

    Normah Ismail; Noorasma Mustakim

    2016-01-01

    Mud clam (Polymesoda erosa) was hydrolysed using two different microbial enzymes; alcalase and flavourzyme. The volatile compounds, amino acids and molecular weight associated with umami and bitter taste in mud clam hydrolysate were determined by head space solid phase micro-extraction gas chromatography (HS-SPME-GCMS), High performance liquid chromatography (HPLC) and sodium dodecyl sulphate polyacrylamide gel electrophoresis (SDS-PAGE). The characteristics of hydrolysates produced using alcalase and flavourzyme were compared. In total, eighteen, seven and six volatile compounds were identified in the flesh, alcalase hydrolysate and flavourzyme hydrolysate, respectively. 2-piperidinone volatile compound content which is associated with bitterness was 6.79 % in alcalase hydrolysate and 3.78 % in flavourzyme hydrolysate. SDS-PAGE results showed that alcalase hydrolysate contains smaller peptide (<52 kDa) compared to flavourzyme hydrolysate (<126 kDa). In addition, sensory analysis using quantitative descriptive analysis (QDA) showed that flavourzyme hydroysate was the least bitter but elicited more umami taste compared to alcalase hydrolysate. Further treatments are still needed to enhance umami taste and to remove bitter taste in mud clam hydrolysate. (author)

  17. Scientific studies on decorated mud mortar of Ajanta

    Directory of Open Access Journals (Sweden)

    M. Singh

    2014-01-01

    Full Text Available This study is an attempt to reveal the decorated earthen plaster of Ajanta. The mud plaster of Ajanta caves has been analyzed with the help of physical and analytical tools. The results indicate that high silt (>70% low clay soil may have been mixed purposefully with lime (calcite for the reason to enhance the cementing characteristics. The presence of calcium oxalate was detected from FTIR spectra may have been the resultant product of proteic materials presented in mud plaster. Ferrugineous silicate along with rarer gluconite–celendonite and white zeolites were also perceived from SEM and FTIR spectral analysis. The existence of quartz and sepiolite in mud mortar was also detected from XRD and SEM studies. The vegetal matter might have been added to tailor the construction behavior. The analytical results authenticate the similarity of earthen plaster of Ajanta and alluvion deposits of Waghura River just in front of caves, probably used as raw material in improvement of new material that suits for restoration for optimize performance and compatibility with the existing materials.

  18. Evaluation of some vanillin-modified polyoxyethylene surfactants as additives for water based mud

    Directory of Open Access Journals (Sweden)

    M.M.A. El-Sukkary

    2014-03-01

    Full Text Available Water-based drilling fluids are increasingly being used for oil and gas exploration and are generally considered to be more environmentally acceptable than oil-based or synthetic-based fluids. In this study, new types of vanillin-modified polyoxyethylene surfactants were evaluated as additives in water-based mud. Their rheological properties in water-based mud were investigated which included the apparent viscosity, the plastic viscosity, the yield point, the gel strength, the thixotropy as well as the filtration properties. Also, the effect of high temperature on the rheology of the formulated water based mud was studied. The tested ethoxylated non-ionic surfactants showed good results when utilized in the formulation of water-based mud.

  19. Fly ash carbon passivation

    Science.gov (United States)

    La Count, Robert B; Baltrus, John P; Kern, Douglas G

    2013-05-14

    A thermal method to passivate the carbon and/or other components in fly ash significantly decreases adsorption. The passivated carbon remains in the fly ash. Heating the fly ash to about 500 and 800 degrees C. under inert gas conditions sharply decreases the amount of surfactant adsorbed by the fly ash recovered after thermal treatment despite the fact that the carbon content remains in the fly ash. Using oxygen and inert gas mixtures, the present invention shows that a thermal treatment to about 500 degrees C. also sharply decreases the surfactant adsorption of the recovered fly ash even though most of the carbon remains intact. Also, thermal treatment to about 800 degrees C. under these same oxidative conditions shows a sharp decrease in surfactant adsorption of the recovered fly ash due to the fact that the carbon has been removed. This experiment simulates the various "carbon burnout" methods and is not a claim in this method. The present invention provides a thermal method of deactivating high carbon fly ash toward adsorption of AEAs while retaining the fly ash carbon. The fly ash can be used, for example, as a partial Portland cement replacement in air-entrained concrete, in conductive and other concretes, and for other applications.

  20. Neutralization of red mud with pickling waste liquor using Taguchi's design of experimental methodology.

    Science.gov (United States)

    Rai, Suchita; Wasewar, Kailas L; Lataye, Dilip H; Mishra, Rajshekhar S; Puttewar, Suresh P; Chaddha, Mukesh J; Mahindiran, P; Mukhopadhyay, Jyoti

    2012-09-01

    'Red mud' or 'bauxite residue', a waste generated from alumina refinery is highly alkaline in nature with a pH of 10.5-12.5. Red mud poses serious environmental problems such as alkali seepage in ground water and alkaline dust generation. One of the options to make red mud less hazardous and environmentally benign is its neutralization with acid or an acidic waste. Hence, in the present study, neutralization of alkaline red mud was carried out using a highly acidic waste (pickling waste liquor). Pickling waste liquor is a mixture of strong acids used for descaling or cleaning the surfaces in steel making industry. The aim of the study was to look into the feasibility of neutralization process of the two wastes using Taguchi's design of experimental methodology. This would make both the wastes less hazardous and safe for disposal. The effect of slurry solids, volume of pickling liquor, stirring time and temperature on the neutralization process were investigated. The analysis of variance (ANOVA) shows that the volume of the pickling liquor is the most significant parameter followed by quantity of red mud with 69.18% and 18.48% contribution each respectively. Under the optimized parameters, pH value of 7 can be achieved by mixing the two wastes. About 25-30% of the total soda from the red mud is being neutralized and alkalinity is getting reduced by 80-85%. Mineralogy and morphology of the neutralized red mud have also been studied. The data presented will be useful in view of environmental concern of red mud disposal.

  1. Characterization of red mud-epoxy intumescent char using surface imaging and micro analysis

    Energy Technology Data Exchange (ETDEWEB)

    Arogundade, A. I., E-mail: ajiunolorioba@gmail.com; Megat-Yusoff, P. S. M., E-mail: puteris@petronas.com.my; Faiz, A. [Department of Mechanical Engineering, Universiti Tecknologi Petronas (Malaysia); Bhat, A. H. [Department of Fundamental and Applied Science, Universiti Tecknologi Petronas (Malaysia)

    2015-07-22

    In this study, red mud (RM), an oxide waste was proposed as reinforcing, synergistic filler for the traditional epoxy intumescent coating (IC). 5.5 wt% of acid-modified and unmodified red mud were introduced into the basic intumescent formulation of ammonium polyphosphate (APP), pentaerythritol (PER) and melamine (MEL). In order to predict effect of modification on its suitability, Field emission electron scanning microscopy and Fourier transform infra red were used to obtain detailed characteristics such as the cell size, pore distribution, homogeneity and chemical composition of the red mud-epoxy carbonaceous char. Both acid-modified and unmodified RM-filled ICs produced chars with smaller and more closely packed cells compared to chars from the unfilled coating. Both coating types had hard carbonaceous metal phosphate coverings that could act as heat barriers. The unmodified red mud was found to be antagonistic to the intumescent action with an expansion of only 2 times the initial thickness. The leached, low iron-red mud produced an expansion of 15 times the initial thickness, but possessed a hollow interior. From these findings, it may be deduced that while acid leaching of red mud may improve intumescent expansion, it would be necessary to optimize the percent filler loading to improve residual mass.

  2. Ashes to ashes: Large Fraxinus germplasm collections and their fates

    Science.gov (United States)

    Kim C. Steiner; Paul. Lupo

    2010-01-01

    As the emerald ash borer (EAB) threatens the survival of our ash species, measures should be taken to preserve their genetic variability in the event that we discover a way to restore populations destroyed by the beetle. As it happens, large germplasm collections exist for our most important and widely distributed eastern species of the genus, white ash (...

  3. Start up study of UASB reactor treating press mud for biohydrogen production

    International Nuclear Information System (INIS)

    Radjaram, B.; Saravanane, R.

    2011-01-01

    Anaerobic digestion of press mud mixed with water for biohydrogen production was performed in continuous fed UASB bioreactor for 120 days. Experiment was conducted by maintaining constant HRT of 30 h and the volume of biohydrogen evolved daily was monitored. Various parameters like COD, VFA, Alkalinity, EC, Volatile solids, pH with respect to biohydrogen production were monitored at regular interval of time. SBPR was 10.98 ml g -1 COD reduced d -1 and 12.77 ml g -1 VS reduced d -1 on peak yield of biohydrogen. COD reduction was above 70 ± 7%. Maximum gas yield was on the 78th day to 2240 ml d -1 . The aim of the experiment is to study the startup process of UASB reactor for biohydrogen production by anaerobic fermentation of press mud. The inoculum for the process is cow dung and water digested in anaerobic condition for 30 days with municipal sewage sludge. The study explores the viability of biohydrogen production from press mud which is a renewable form of energy to supplement the global energy crisis. -- Highlights: → Feasibility of biohydrogen production from press mud was explored in this study. The gas yield was maximum on the 78th day to 2240 ml d -1 with H 2 % of 52-59%. Biohydrogen yield was about 890 ml kg -1 press mud added d -1 . Press mud is identified as an excellent potential waste to tap energy.

  4. Function of drilling mud during well boring

    Energy Technology Data Exchange (ETDEWEB)

    Martinko, B

    1982-01-01

    This paper provides an analysis of primary functions that an emulsion mud must have when shallow wells are drilled: remove drilled waste matter from well, monitor stratal pressure, retain material when circulation is absent, release material to the surface, form an impermeable clay coating on walls of the well, prevent caving of soil, and prevent instrument corrosion. Recommendations are provided to achieve the above listed requirements in mud characteristics: density, filtration, viscosity, gelation and alkalization must be adjusted to the given requirements. It is concluded that fresh water alone cannot satisfy all the necessary requirements and it is recommended to avoid using it where possible, and instead utilize water with additives (emulsions). A number of water and additive compositions are offered. A polymer solution, consisting of water, NaCl or CaCl/sub 2/ to the required density, polymer (vegetative rubber or hydroxethylcellulose) in the amount of 3-6 kg/m/sup 3/ for circulation and 6-9 kg/m/sup 3/ when there's mud loss, can be utilized. Also finely ground CaCO/sub 3/ in the amount of 20-30 kg/m/sup 3/ can be utilized for cementing media. Formulas for a bentonite emulsion and others are included.

  5. Fusion characterization of biomass ash

    Energy Technology Data Exchange (ETDEWEB)

    Ma, Teng [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Sino-Danish Center for Education and Research, Beijing, 100190 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Fan, Chuigang; Hao, Lifang [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Li, Songgeng, E-mail: sgli@ipe.ac.cn [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Song, Wenli [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Lin, Weigang [State Key Laboratory ofMultiphase Complex Systems, Institute of Process Engineering, Chinese Academy of Sciences, No. 1 Zhongguancun North Second Street, Beijing 100190 (China); Department of Chemical and Biochemical Engineering, Technical University of Denmark, 2800 Kgs. Lyngby (Denmark)

    2016-08-20

    Highlights: • A novel method is proposed to analyze fusion characteristics of biomass ash. • T{sub m} can represent the severe melting temperature of biomass ash. • Compared with AFT, TMA is the better choice to analyze the fusion characteristics of biomass ash. - Abstract: The ash fusion characteristics are important parameters for thermochemical utilization of biomass. In this research, a method for measuring the fusion characteristics of biomass ash by Thermo-mechanical Analyzer, TMA, is described. The typical TMA shrinking ratio curve can be divided into two stages, which are closely related to ash melting behaviors. Several characteristics temperatures based on the TMA curves are used to assess the ash fusion characteristics. A new characteristics temperature, T{sub m}, is proposed to represent the severe melting temperature of biomass ash. The fusion characteristics of six types of biomass ash have been measured by TMA. Compared with standard ash fusibility temperatures (AFT) test, TMA is more suitable for measuring the fusion characteristics of biomass ash. The glassy molten areas of the ash samples are sticky and mainly consist of K-Ca-silicates.

  6. Biogeochemical interactions among the arsenic, iron, humic substances, and microbes in mud volcanoes in southern Taiwan.

    Science.gov (United States)

    Liu, Chia-Chuan; Maity, Jyoti Prakash; Jean, Jiin-Shuh; Sracek, Ondra; Kar, Sandeep; Li, Zhaohui; Bundschuh, Jochen; Chen, Chien-Yen; Lu, Hsueh-Yu

    2011-01-01

    Fluid and mud samples collected from Hsiaokunshui (HKS), Wushanting (WST), Yenshuikeng (YSK), Kunshuiping (KSP), Liyushan (LYS), and Sinyangnyuhu (SYNH) mud volcanoes of southwestern Taiwan were characterized for major ions, humic substances (HS) and trace elements concentrations. The relationship between the release of arsenic (As) and activities of sulfate-reducing bacteria has been assessed to understand relevant geochemical processes in the mud volcanoes. Arsenic (0.02-0.06 mg/L) and humic substances (4.13 × 10(-4) to 1.64 × 10(-3) mM) in the fluids of mud volcanoes showed a positive correlation (r = 0.99, p volcano. Arsenic and iron in mud sediments formed two separate groups i) high As, but low Fe in HKS, WST, and SYNH; and ii) low As, but high Fe in the YSK, KSP, and LYS mud volcanoes. The Eh(S.H.E.) values of the mud volcano liquids were characterized by mild to strongly reducing conditions. The HKS, SYNH, and WST mud volcanoes (near the Chishan Fault) belongs to strong reducing environment (-33 to -116 mV), whereas the LYS, YSK, and KSP mud volcanoes located near the coastal plain are under mild reducing environment (-11 to 172 mV). At low Eh values mud volcanoes, saturation index (SI) values of poorly crystalline phases such as amorphous ferric hydroxide indicate understaturation, whereas saturation is reached in relatively high Eh(S.H.E.) values mud volcanoes. Arsenic contents in sediments are low, presumably due to its release to fluids (As/Fe ratio in YSK, KSP, and LYS sediment: 4.86 × 10(-4)-6.20 × 10(-4)). At low Eh(S.H.E.) values (mild to strong reducing environment), arsenic may co-precipitate with sulfides as a consequence of sulfate reduction (As/Fe ratios in WST, HKS, and SYNH sediments: 0.42-0.69).

  7. Trace elements in coal ash

    Science.gov (United States)

    Deonarine, Amrika; Kolker, Allan; Doughten, Michael W.

    2015-01-01

    Coal ash is a residual waste product primarily produced by coal combustion for electric power generation. Coal ash includes fly ash, bottom ash, and flue-gas desulfurization products (at powerplants equipped with flue-gas desulfurization systems). Fly ash, the most common form of coal ash, is used in a range of products, especially construction materials. A new Environmental Protection Agency ruling upholds designation of coal ash as a non-hazardous waste under Subtitle D of the Resource Conservation and Recovery Act, allowing for the continued beneficial use of coal ash and also designating procedures and requirements for its storage.

  8. Mobility of 232Th and 210Po in red mud.

    Science.gov (United States)

    Hegedűs, Miklós; Tóth-Bodrogi, Edit; Jónás, Jácint; Somlai, János; Kovács, Tibor

    2018-04-01

    The valorization of industrial by-products such as red mud became a tempting opportunity, but the understanding of the risks involved is required for the safe utilization of these products. One of the risks involved are the elevated levels of radionuclides (in the 100-1300 Bq/kg range for both the 238 U and 232  Th decay chains, but usually lower than 1000 Bq/kg, which is the recommended limit for excemption or clearance according to the EU BSS released in 2013) in red mud that can affect human health. There is no satisfactory answer for the utilization of red mud; the main current solution is still almost exclusively disposal into a landfill. For the safe utilization and deposition of red mud, it is important to be able to assess the leaching behaviour of radionuclides. Because there is no commonly accepted measurement protocol for testing the leaching of radionuclides in the EU a combined measurement protocol was made and tested based on heavy metal leaching methods. The leaching features of red mud were studied by methods compliant with the MSZ-21470-50 Hungarian standard, the CEN/TS 14429 standard and the Tessier sequential extraction method for 232 Th and 210 Po. The leached solutions were taken to radiochemical separation followed by spontaneous deposition for Po and electrodeposition for Th. The 332 ± 33 Bq/kg 232 Th content was minimally mobile, 1% became available for distilled water 1% and 6% for Lakanen-Erviö solution; the Tessier extraction showed minimal mobility in the first four steps, while more than 85% remained in the residue. The 210 Po measurements had a severe disturbing effect in many cases, probably due to large amounts of iron present in the red mud, from the 310 ± 12 Bq/kg by aqua regia digestion, distilled water mobilized 23%, while Lakanen-Erviö solution mobilized ∼13%. The proposed protocol is suitable for the analysis of Th and Po leaching behaviour. Copyright © 2018 Elsevier Ltd. All rights reserved.

  9. Mercury release from fly ashes and hydrated fly ash cement pastes

    Science.gov (United States)

    Du, Wen; Zhang, Chao-yang; Kong, Xiang-ming; Zhuo, Yu-qun; Zhu, Zhen-wu

    2018-04-01

    The large-scale usage of fly ash in cement and concrete introduces mercury (Hg) into concrete structures and a risk of secondary emission of Hg from the structures during long-term service was evaluated. Three fly ashes were collected from coal-fired power plants and three blend cements were prepared by mixing Ordinary Portland cement (OPC) with the same amount of fly ash. The releasing behaviors of Hg0 from the fly ash and the powdered hydrated cement pastes (HCP) were measured by a self-developed Hg measurement system, where an air-blowing part and Hg collection part were involved. The Hg release of fly ashes at room temperature varied from 25.84 to 39.69 ng/g fly ash during 90-days period of air-blowing experiment. In contrast, the Hg release of the HCPs were in a range of 8.51-18.48 ng/g HCP. It is found that the Hg release ratios of HCPs were almost the same as those of the pure fly ashes, suggesting that the hydration products of the HCP have little immobilization effect on Hg0. Increasing temperature and moisture content markedly promote the Hg release.

  10. Fly ash aggregates. Vliegaskunstgrind

    Energy Technology Data Exchange (ETDEWEB)

    1983-03-01

    A study has been carried out into artificial aggregates made from fly ash, 'fly ash aggregates'. Attention has been drawn to the production of fly ash aggregates in the Netherlands as a way to obviate the need of disposal of fly ash. Typical process steps for the manufacturing of fly ash aggregates are the agglomeration and the bonding of fly ash particles. Agglomeration techniques are subdivided into agitation and compaction, bonding methods into sintering, hydrothermal and 'cold' bonding. In sintering no bonding agent is used. The fly ash particles are more or less welded together. Sintering in general is performed at a temperature higher than 900 deg C. In hydrothermal processes lime reacts with fly ash to a crystalline hydrate at temperatures between 100 and 250 deg C at saturated steam pressure. As a lime source not only lime as such, but also portland cement can be used. Cold bonding processes rely on reaction of fly ash with lime or cement at temperatures between 0 and 100 deg C. The pozzolanic properties of fly ash are used. Where cement is applied, this bonding agent itself contributes also to the strength development of the artificial aggregate. Besides the use of lime and cement, several processes are known which make use of lime containing wastes such as spray dry absorption desulfurization residues or fluid bed coal combustion residues. (In Dutch)

  11. Geoelectric monitoring at the Boulder magnetic observatory

    Directory of Open Access Journals (Sweden)

    C. C. Blum

    2017-11-01

    Full Text Available Despite its importance to a range of applied and fundamental studies, and obvious parallels to a robust network of magnetic-field observatories, long-term geoelectric field monitoring is rarely performed. The installation of a new geoelectric monitoring system at the Boulder magnetic observatory of the US Geological Survey is summarized. Data from the system are expected, among other things, to be used for testing and validating algorithms for mapping North American geoelectric fields. An example time series of recorded electric and magnetic fields during a modest magnetic storm is presented. Based on our experience, we additionally present operational aspects of a successful geoelectric field monitoring system.

  12. Hydration of fly ash cement and microstructure of fly ash cement pastes

    Energy Technology Data Exchange (ETDEWEB)

    Shiyuan, H.

    1981-01-01

    The strength development and hydration of fly ash cement and the influence of addition of gypsum on those were studied at normal and elevated temperatures. It was found that an addition of a proper amount of gypsum to fly ash cement could accelerate the pozzolanic reaction between CH and fly ash, and as a result, increase the strength of fly ash cement pastes after 28 days.

  13. Glass-ceramic from mixtures of bottom ash and fly ash.

    Science.gov (United States)

    Vu, Dinh Hieu; Wang, Kuen-Sheng; Chen, Jung-Hsing; Nam, Bui Xuan; Bac, Bui Hoang

    2012-12-01

    Along with the gradually increasing yield of the residues, appropriate management and treatment of the residues have become an urgent environmental protection problem. This work investigated the preparation of a glass-ceramic from a mixture of bottom ash and fly ash by petrurgic method. The nucleation and crystallization kinetics of the new glass-ceramic can be obtained by melting the mixture of 80% bottom ash and 20% fly ash at 950 °C, which was then cooled in the furnace for 1h. Major minerals forming in the glass-ceramics mainly are gehlenite (Ca(2)Al(2)SiO(7)) & akermanite (Ca(2)MgSiO(7)) and wollastonite (CaSiO(3)). In addition, regarding chemical/mechanical properties, the chemical resistance showing durability, and the leaching concentration of heavy metals confirmed the possibility of engineering and construction applications of the most superior glass-ceramic product. Finally, petrurgic method of a mixture of bottom ash and fly ash at 950 °C represents a simple, inexpensive, and energy saving method compared with the conventional heat treatment. Copyright © 2012 Elsevier Ltd. All rights reserved.

  14. Effects of mud supply on large-scale estuary morphology and development over centuries to millennia

    Directory of Open Access Journals (Sweden)

    L. Braat

    2017-10-01

    Full Text Available Alluvial river estuaries consist largely of sand but are typically flanked by mudflats and salt marshes. The analogy with meandering rivers that are kept narrower than braided rivers by cohesive floodplain formation raises the question of how large-scale estuarine morphology and the late Holocene development of estuaries are affected by cohesive sediment. In this study we combine sand and mud transport processes and study their interaction effects on morphologically modelled estuaries on centennial to millennial timescales. The numerical modelling package Delft3D was applied in 2-DH starting from an idealised convergent estuary. The mixed sediment was modelled with an active layer and storage module with fluxes predicted by the Partheniades–Krone relations for mud and Engelund–Hansen for sand. The model was subjected to a range of idealised boundary conditions of tidal range, river discharge, waves and mud input. The model results show that mud is predominantly stored in mudflats on the side of the estuary. Marine mud supply only influences the mouth of the estuary, whereas fluvial mud is distributed along the whole estuary. Coastal waves stir up mud and remove the tendency to form muddy coastlines and the formation of mudflats in the downstream part of the estuary. Widening continues in estuaries with only sand, while mud supply leads to a narrower constant width and reduced channel and bar dynamics. This self-confinement eventually leads to a dynamic equilibrium in which lateral channel migration and mudflat expansion are balanced on average. However, for higher mud concentrations, higher discharge and low tidal amplitude, the estuary narrows and fills to become a tidal delta.

  15. Experimental Evidence that Abrasion of Carbonate Sand is a Significant Source of Carbonate Mud

    Science.gov (United States)

    Trower, L.; Kivrak, L.; Lamb, M. P.; Fischer, W. W.

    2017-12-01

    Carbonate mud is a major sedimentary component of modern and ancient tropical carbonate environments, yet its enigmatic origin remains debated. Early views on the origin of carbonate mud considered the abrasion of carbonate sand during sediment transport as a possible mechanism. In recent decades, however, prevailing thought has generally settled on a binary explanation: 1) precipitation of aragonite needles within the water column, and 2) post-mortem dispersal of biological aragonite, in particular from algae, and perhaps aided by fish. To test these different hypotheses, we designed a model and a set of laboratory experiments to quantify the rates of mud production associated with sediment transport. We adapted a recent model of ooid abrasion rate to predict the rate of mud production by abrasion of carbonate sand as a function of grain size and sediment transport mode. This model predicts large mud production rates, ranging from 103 to 104 g CaCO3/m2/yr for typical grain sizes and transport conditions. These rate estimates are at least one order of magnitude more rapid than the 102 g CaCO3/m2/yr estimates for other mechanisms like algal biomineralization, indicating that abrasion could produce much larger mud fluxes per area as other mechanisms. We tested these estimates using wet abrasion mill experiments; these experiments generated mud through mechanical abrasion of both ooid and skeletal carbonate sand for grain sizes ranging from 250 µm to >1000 µm over a range of sediment transport modes. Experiments were run in artificial seawater, including a series of controls demonstrating that no mud was produced via homogenous nucleation and precipitation in the absence of sand. Our experimental rates match the model predictions well, although we observed small systematic differences in rates between abrasion ooid sand and skeletal carbonate sand that likely stems from innate differences in grain angularity. Electron microscopy of the experimental products revealed

  16. Dependence of radon emanation of red mud bauxite processing wastes on heat treatment

    International Nuclear Information System (INIS)

    Jobbagy, V.; Somlai, J.; Kovacs, J.; Szeiler, G.; Kovacs, T.

    2009-01-01

    Natural radioactivity content, radon emanation and some other physical characteristics of red mud were investigated, so that to identify the possibilities of the safe utilization of such material as a building material additive. Based on the radionuclide concentration, red mud is not permitted to be used directly as a building material, however, mixing of a maximum 20% red mud and 80% clay meets the requirements. The main aim of this work was to determine the dependence of the emanation factor of red mud firing temperature and some other parameters. The relevant experimental procedure was carried out in two different ways: without any additional material, and by adding a known amount of sawdust (5-35 wt%) then firing the sample at a given temperature (100-1000 deg. C). The average emanation factor of the untreated dry red mud was estimated to 20%, which decreased to about 5% at a certain heat treatment. Even lower values were found using semi-reductive atmosphere. It has been concluded that all emanation measurements results correlate well to the firing temperature, the specific surface and the pore volume.

  17. Alternatives Analysis Amchitka Island Mud Pit Cap Repair, Amchitka, Alaska January 2016

    Energy Technology Data Exchange (ETDEWEB)

    Darr, Paul S. [US Department of Energy, Washington, DC (United States). Office of Legacy Management

    2016-01-01

    The U.S. Department of Energy (DOE) Office of Legacy Management (LM) manages the Nevada Offsites program, which includes a series of reclaimed drilling mud impoundments on Amchitka Island, Alaska (Figure 1). Navarro Research and Engineering, Inc. is the Legacy Management Support contractor (the Contractor) for LM. The Contractor has procured Tetra Tech, Inc. to provide engineering support to the Amchitka mud pit reclamation project. The mud pit caps were damaged during a 7.9-magnitude earthquake that occurred in 2014. The goals of the current project are to investigate conditions at the mud pit impoundments, identify feasible alternatives for repair of the cover systems and the contents, and estimate relative costs of repair alternatives. This report presents descriptions of the sites and past investigations, existing conditions, summaries of various repair/mitigation alternatives, and direct, unburdened, order-of-magnitude (-15% to +50%) associated costs.

  18. Fusion characterization of biomass ash

    DEFF Research Database (Denmark)

    Ma, Teng; Fan, Chuigang; Hao, Lifang

    2016-01-01

    The ash fusion characteristics are important parameters for thermochemical utilization of biomass. In this research, a method for measuring the fusion characteristics of biomass ash by Thermo-mechanical Analyzer, TMA, is described. The typical TMA shrinking ratio curve can be divided into two...... stages, which are closely related to ash melting behaviors. Several characteristics temperatures based on the TMA curves are used to assess the ash fusion characteristics. A new characteristics temperature, Tm, is proposed to represent the severe melting temperature of biomass ash. The fusion...... characteristics of six types of biomass ash have been measured by TMA. Compared with standard ash fusibility temperatures (AFT) test, TMA is more suitable for measuring the fusion characteristics of biomass ash. The glassy molten areas of the ash samples are sticky and mainly consist of K-Ca-silicates....

  19. Arsenic, chromium and mercury removal using mussel shell ash or a sludge/ashes waste mixture.

    Science.gov (United States)

    Seco-Reigosa, Natalia; Peña-Rodríguez, Susana; Nóvoa-Muñoz, Juan Carlos; Arias-Estévez, Manuel; Fernández-Sanjurjo, María J; Alvarez-Rodríguez, Esperanza; Núñez-Delgado, Avelino

    2013-04-01

    Different batches of valued mussel shell and waste mussel shell ash are characterised. Shell ash has pH > 12 and high electrical conductivities (between 16.01 and 27.27 dS m(-1)), while calcined shell shows pH values up to 10.7 and electrical conductivities between 1.19 and 3.55 dS m(-1). X-ray fluorescence, nitric acid digestion and water extractions show higher concentrations in shell ash for most parameters. Calcite is the dominant crystalline compound in this ash (95.6%), followed by aragonite. Adsorption/desorption trials were performed for mussel shell ash and for a waste mixture including shell ash, sewage sludge and wood ash, showing the following percentage adsorptions: Hg(II) >94%, As(V) >96% and Cr(VI) between 11 and 30% for shell ash; Hg(II) >98%, As(V) >88% and Cr(VI) between 30 and 88% for the waste mixture. Hg and As desorption was ash and the waste mixture, while Cr desorption was between 92 and 45% for shell ash, and between 19 and 0% for the mixture. In view of that, mussel shell ash and the mixture including shell ash, sewage sludge and wood ash could be useful for Hg(II) and As(V) removal.

  20. Safety evaluation of traces of nickel and chrome in cosmetics: The case of Dead Sea mud.

    Science.gov (United States)

    Ma'or, Ze'evi; Halicz, Ludwik; Portugal-Cohen, Meital; Russo, Matteo Zanotti; Robino, Federica; Vanhaecke, Tamara; Rogiers, Vera

    2015-12-01

    Metal impurities such as nickel and chrome are present in natural ingredients-containing cosmetic products. These traces are unavoidable due to the ubiquitous nature of these elements. Dead Sea mud is a popular natural ingredient of cosmetic products in which nickel and chrome residues are likely to occur. To analyze the potential systemic and local toxicity of Dead Sea mud taking into consideration Dead Sea muds' natural content of nickel and chrome. The following endpoints were evaluated: (Regulation No. 1223/20, 21/12/2009) systemic and (SCCS's Notes of Guidance) local toxicity of topical application of Dead Sea mud; health reports during the last five years of commercial marketing of Dead Sea mud. Following exposure to Dead Sea mud, MoS (margin of safety) calculations for nickel and chrome indicate no toxicological concern for systemic toxicity. Skin sensitization is also not to be expected by exposure of normal healthy skin to Dead Sea mud. Topical application, however, is not recommended for already nickel-or chrome-sensitized persons. As risk assessment of impurities present in cosmetics may be a difficult exercise, the case of Dead Sea mud is taken here as an example of a natural material that may contain traces of unavoidable metals. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

  1. Exploring the molecular and biochemical basis of ash resistance to emerald ash borer

    Science.gov (United States)

    Justin G.A. Whitehill; Daniel A. Herms; Pierluigi. Bonello

    2010-01-01

    Larvae of the emerald ash borer (EAB) (Agrilus planipennis) feed on phloem of ash (Fraxinus spp.) trees. It is hypothesized that the resistance of Asian species of ash (e.g., Manchurian ash, F. mandshurica) to EAB is due to endogenous defenses present in phloem tissues in the form of defensive proteins and/or...

  2. Properties and Leachability of Self-Compacting Concrete Incorporated with Fly Ash and Bottom Ash

    Science.gov (United States)

    Kadir, Aeslina Abdul; Ikhmal Haqeem Hassan, Mohd; Jamaluddin, Norwati; Bakri Abdullah, Mohd Mustafa Al

    2016-06-01

    The process of combustion in coal-fired power plant generates ashes, namely fly ash and bottom ash. Besides, coal ash produced from coal combustion contains heavy metals within their compositions. These metals are toxic to the environment as well as to human health. Fortunately, treatment methods are available for these ashes, and the use of fly ash and bottom ash in the concrete mix is one of the few. Therefore, an experimental program was carried out to study the properties and determine the leachability of selfcompacting concrete incorporated with fly ash and bottom ash. For experimental study, self-compacting concrete was produced with fly ash as a replacement for Ordinary Portland Cement and bottom ash as a replacement for sand with the ratios of 10%, 20%, and 30% respectively. The fresh properties tests conducted were slump flow, t500, sieve segregation and J-ring. Meanwhile for the hardened properties, density, compressive strength and water absorption test were performed. The samples were then crushed to be extracted using Toxicity Characteristic Leaching Procedure and heavy metals content within the samples were identified accordingly using Atomic Absorption Spectrometry. The results demonstrated that both fresh and hardened properties were qualified to categorize as self-compacting concrete. Improvements in compressive strength were observed, and densities for all the samples were identified as a normal weight concrete with ranges between 2000 kg/m3 to 2600 kg/m3. Other than that, it was found that incorporation up to 30% of the ashes was safe as the leached heavy metals concentration did not exceed the regulatory levels, except for arsenic. In conclusion, this study will serve as a reference which suggests that fly ash and bottom ash are widely applicable in concrete technology, and its incorporation in self-compacting concrete constitutes a potential means of adding value to appropriate mix and design.

  3. Effect of ash components on the ignition and burnout of high ash coals

    Energy Technology Data Exchange (ETDEWEB)

    Feng, B.; Yan, R.; Zheng, C.G. [Huazhong University of Science and Technology, Wuhan (China). National Laboratory of Coal Combustion

    1998-11-01

    The effect of the ash components on the ignition and burnout of four Chinese high ash coals were studied by thermogravimetric analysis. To investigate the influence of the ash components, comparative experiments were carried out with original, deashed and impregnated coals. Eleven types of ash components, such as SiO{sub 2}, CaCO{sub 3}, MgO, Na{sub 2}CO{sub 3}, K{sub 2}CO{sub 3}, Al{sub 2}O{sub 3}, TiO{sub 2}, Fe{sub 2}O{sub 3}, FeS{sub 2}, NH{sub 4}Fe(SO{sub 4}){sub 2}{center_dot}12H{sub 2}O and FeSO{sub 4},(NH{sub 4}){center_dot}6H{sub 2}O were used in the present study. It was found that most of the ash components have negative effects. The strong influence of some ash components suggests that the combustion characteristics of high ash coal may be determined by the ash composition. 5 refs., 2 figs., 2 tabs.

  4. Gypsum addition to soils contaminated by red mud: implications for aluminium, arsenic, molybdenum and vanadium solubility.

    Science.gov (United States)

    Lehoux, Alizée P; Lockwood, Cindy L; Mayes, William M; Stewart, Douglas I; Mortimer, Robert J G; Gruiz, Katalin; Burke, Ian T

    2013-10-01

    Red mud is highly alkaline (pH 13), saline and can contain elevated concentrations of several potentially toxic elements (e.g. Al, As, Mo and V). Release of up to 1 million m(3) of bauxite residue (red mud) suspension from the Ajka repository, western Hungary, caused large-scale contamination of downstream rivers and floodplains. There is now concern about the potential leaching of toxic metal(loid)s from the red mud as some have enhanced solubility at high pH. This study investigated the impact of red mud addition to three different Hungarian soils with respect to trace element solubility and soil geochemistry. The effectiveness of gypsum amendment for the rehabilitation of red mud-contaminated soils was also examined. Red mud addition to soils caused a pH increase, proportional to red mud addition, of up to 4 pH units (e.g. pH 7 → 11). Increasing red mud addition also led to significant increases in salinity, dissolved organic carbon and aqueous trace element concentrations. However, the response was highly soil specific and one of the soils tested buffered pH to around pH 8.5 even with the highest red mud loading tested (33 % w/w); experiments using this soil also had much lower aqueous Al, As and V concentrations. Gypsum addition to soil/red mud mixtures, even at relatively low concentrations (1 % w/w), was sufficient to buffer experimental pH to 7.5-8.5. This effect was attributed to the reaction of Ca(2+) supplied by the gypsum with OH(-) and carbonate from the red mud to precipitate calcite. The lowered pH enhanced trace element sorption and largely inhibited the release of Al, As and V. Mo concentrations, however, were largely unaffected by gypsum induced pH buffering due to the greater solubility of Mo (as molybdate) at circumneutral pH. Gypsum addition also leads to significantly higher porewater salinities, and column experiments demonstrated that this increase in total dissolved solids persisted even after 25 pore volume replacements. Gypsum

  5. Shedding of ash deposits

    DEFF Research Database (Denmark)

    Zbogar, Ana; Frandsen, Flemming; Jensen, Peter Arendt

    2009-01-01

    Ash deposits formed during fuel thermal conversion and located on furnace walls and on convective pass tubes, may seriously inhibit the transfer of heat to the working fluid and hence reduce the overall process efficiency. Combustion of biomass causes formation of large quantities of troublesome...... ash deposits which contain significant concentrations of alkali, and earth-alkali metals. The specific composition of biomass deposits give different characteristics as compared to coal ash deposits, i.e. different physical significance of the deposition mechanisms, lower melting temperatures, etc....... Low melting temperatures make straw ashes especially troublesome, since their stickiness is higher at lower temperatures, compared to coal ashes. Increased stickiness will eventually lead to a higher collection efficiency of incoming ash particles, meaning that the deposit may grow even faster...

  6. Mariana Forearc Serpentine Mud Volcanoes Harbor Novel Communities of Extremophilic Archaea

    Science.gov (United States)

    Curtis, A. C.; Moyer, C. L.

    2005-12-01

    Since the Eocene (45 Ma) the Pacific Plate has been subducting beneath the Philippine Plate in the western Pacific ocean. This process has given rise to the Mariana Islands. As a direct result of this non-accretionary subduction, the Mariana Island Arc contains a broad forearc zone of serpentinite mud volcanoes located between the island chain and the trench. Forearc faulting, due to high pressure and low temperature build-up, produce slurries of mud and rock that mix with slab derived fluids and rise in conduits. Due to dehydration of the overlying mantle, native rock is converted to serpentinite, which squeezes out at fractures along the sea floor. This results in giant mud volcanoes (~30 km diameter and ~2 km high) that form a chain between 50 and 150 km behind the trench axis. Microbial samples were collected using Jason II from seven mud volcanoes along the length of the forearc and community fingerprinting was applied to genomic DNA using terminal restriction length polymorphism (T-RFLP). The resulting data were compared with traditional clone library and sequence analysis from samples obtained from the southernmost mud volcano, South Chamorro, site 1200, holes D and E, sampled during ODP Leg 195. The dominant archaeal phylotypes found clustered into two groups within the Methanobacteria, a class of anaerobic methanogens and methylotrophs. These phylotypes were detected at three of the seven mud volcanoes sampled and comprised 61% of the archaeal clone library from 1200 E. The first group was most closely related to the order Methanobacteriales, however, these novel phylotypes had similarity values of up to 0.90 at best with some resulting at 0.48. The second novel group of phylotypes were most closely related to order Methanosarcinales, with similarity values in the range of 0.50 to 0.22, indicating a relatively weak association with known phylotypes. At 1200 D, phylotypes associated with non-thermophilic Marine Group I Crenarchaeota were detected

  7. Pengaruh Kombinasi Fly Ash dan Bottom Ash sebagai Bahan Substitusi pada Campuran Beton terhadap Sifat Mekanis

    OpenAIRE

    Yahya, Tengku Tantoni; Kurniawandy, Alex; Djauhari, Zulfikar

    2017-01-01

    Fly ash and bottom ash were waste that generated from the power plant burning coal process. Fly ash and bottom ash has the potential to be developed as a basic ingredient in concrete composites. This research aimed to obtain the properties of fresh concrete and hard concrete of the combined effect of fly ash and bottom ash as a substitute ingredient in composite concrete. This research has examined the influence of a combination of waste fly ash and bottom ash to the compressive strength of a...

  8. Red mud enhances methanogenesis with the simultaneous improvement of hydrolysis-acidification and electrical conductivity.

    Science.gov (United States)

    Ye, Jie; Hu, Andong; Ren, Guoping; Zhou, Ting; Zhang, Guangming; Zhou, Shungui

    2018-01-01

    The role of red mud in the improvement of methanogenesis during sludge anaerobic digestion was innovatively investigated in this study. The results demonstrated that the addition of 20g/L red mud resulted in a 35.5% increase in methane accumulation. Red mud effectively promoted the hydrolysis-acidification of organic compounds in the sludge, which resulted in the increase of protein, polysaccharide, and VFAs by 5.1-94.5%. The activities of key enzymes were improved by 41.4-257.3%. Electrochemical measurements presented direct evidence that the electrical conductivity was significantly improved with red mud. More conductive magnetite was formed during the secondary mineralization after Fe(III) reduction by Fe (III)-reducing genes such as Clostridiaceae and Ruminococcaceae. The higher conductivity enhanced the electron transfer between the syntrophic bacteria (Geobacteraceae) and methanogens (Methanosaeta and Methanosarcina), and then improved the methanogenesis. This research provides a novel perspective on the synergism between sludge and red mud for methane production. Copyright © 2017 Elsevier Ltd. All rights reserved.

  9. Evaluation of red mud as pozzolanic material in replacement of cement for production of mortars

    International Nuclear Information System (INIS)

    Manfroi, E.P.; Cheriaf, M.; Rocha, J.C.

    2010-01-01

    Red mud is a by-product of the alkaline extraction of aluminum from the bauxite and represents a renewed environmental problem due the significant annual throughput by the plants. In the present work, the pozzolanic properties of Brazilian red mud fired at 600, 700, 800 and 900 deg C were investigated by monitoring lime consumption using DTA analysis and Brazilian standard methodology NBR 5772 (1992). Products and kinetics of hydration were determined in cement pastes produced with 5 and 15% red mud using x-ray diffraction and DTA analysis. Compressive strength and capillary absorption tests were realized on mortars constituted by 5, 10 and 15% red mud in replacement of cement. When calcined at 600 deg C, the red mud develops good pozzolanic properties, and the compressive strength of mortars produced with this waste meet values in accordance with regulatory standard. These results shown than red mud can be used, in partial replacement of cement, as new construction material to produce sustainable mortars with low environmental impact. (author)

  10. The Dead Sea Mud and Salt: A Review of Its Characterization, Contaminants, and Beneficial Effects

    Science.gov (United States)

    Bawab, Abeer Al; Bozeya, Ayat; Abu-Mallouh, Saida; Abu Irmaileh, Basha'er; Daqour, Ismail; Abu-Zurayk, Rund A.

    2018-02-01

    The Dead Sea has been known for its therapeutic and cosmetic properties. The unique climatic conditions in the Dead Sea area make it a renowned site worldwide for the field of climatotherapy, which is a natural approach for the provision of medications for many human diseases including unusual exclusive salt composition of the water, a special natural mud, thermal mineral springs, solar irradiation, oxygen-rich and bromine-rich haze. This review focuses on the physical, chemical, and biological characteristics of the Dead Sea mud and salts, in addition to their contaminants, allowing this review to serve as a guide to interested researchers to their risks and the importance of treatment. Beneficial effects of Dead Sea mud and salts are discussed in terms of therapy and cosmetics. Additional benefits of both Dead Sea mud and salts are also discussed, such as antimicrobial action of the mud in relation to its therapeutic properties, and the potency of mud and salts to be a good medium for the growth of a halophilic unicellular algae, used for the commercial production of β-carotene Dunaliella.

  11. Geochemical studies of the White Breccia Boulders at North Ray Crater, Descartes region of the lunar highlands

    Science.gov (United States)

    Lindstrom, M. M.; Lindstrom, D. J.; Lum, R. K. L.; Schuhmann, P. J.; Nava, D. F.; Schuhmann, S.; Philpotts, J. A.; Winzer, S. R.

    1977-01-01

    The samples of the White Breccia Boulders obtained during the Apollo 16 mission and investigated in the reported study include an anorthositic breccia (67415), a dark matrix breccia (67435), a light matrix breccia (67455), and a large clast of dark matrix breccia (67475) taken from the 67455 boulder. The chemical analyses of bulk samples of the samples are listed in a table. A graph shows the lithophile trace element abundances. Another graph indicates the variation of Sm with Al2O3 content for samples from the White Breccia Boulders. The North Ray Crater breccias are found to be in general slightly more aluminous than breccias from the other stations at the Apollo 16 site. Analyses of eight Apollo 16 breccias cited in the literature range from 25% to 35% Al2O3. However, the North Ray Crater breccias are more clearly distinct from the other Apollo 16 breccias in their contents of lithophile trace elements.

  12. Biodiesel Production from Castor Oil by Using Calcium Oxide Derived from Mud Clam Shell

    OpenAIRE

    Ismail, S.; Ahmed, A. S.; Anr, Reddy; Hamdan, S.

    2016-01-01

    The catalytic potential of calcium oxide synthesized from mud clam shell as a heterogeneous catalyst for biodiesel production was studied. The mud clam shell calcium oxide was characterized using particle size analyzer, Fourier transform infrared spectroscopy, scanning electron microscopy, and BET gas sorption analyzer. The catalyst performance of mud clam shell calcium oxide was studied in the transesterification of castor oil as biodiesel. Catalyst characterization and transesterification s...

  13. New technology of extracting the amount of rare earth metals from the red mud

    International Nuclear Information System (INIS)

    Martoyan, G A; Karamyan, G G; Vardan, G A

    2016-01-01

    The paper outlined the environmental and economic problems associated with red mud - the waste generated in processing of bauxite ore for aluminum production. The chemical analysis of red mud has identified a number of useful elements including rare earth metals. The electromembrane technology of red mud processing with extraction of valuable elements is described. A possible scheme of separation of these metals through electrolysis is also given. (paper)

  14. Environmental impact of toxic elements in red mud studied by fractionation and speciation procedures.

    Science.gov (United States)

    Milačič, Radmila; Zuliani, Tea; Ščančar, Janez

    2012-06-01

    Aluminum (Al) is mostly produced from bauxite ore, which contains up to 70% of Al(2)O(3) (alumina). Before alumina is refined to aluminum metal, it is purified by hot alkaline extraction. As a waste by-product red mud is formed. Due to its high alkalinity and large quantities, it represents a severe disposal problem. In Kidričevo (Slovenia), red mud was washed with water before disposal, and after drying, covered with soil. In Ajka (Hungary), the red mud slurry was collected directly in a containment structure, which burst caused a major accident in October 2010. In the present work the environmental impact of toxic elements in red mud from Kidričevo and Ajka were evaluated by applying a sequential extraction procedure and speciation analysis. The predominant red mud fraction was the insoluble residue; nevertheless, environmental concern was focused on the highly mobile water-soluble fraction of Al and Cr. Al in the water-soluble Ajka mud fraction was present exclusively in form of toxic [Al(OH)(4)](-), while Cr existed in its toxic hexavalent form. Comparative assessment to red mud from Kidričevo (Slovenia) with a lower alkalinity (pH 9) with that from Ajka demonstrated significantly lower Al solubility and the presence of only trace amounts of Cr(VI), confirming that disposal of neutralized mud is environmentally much more acceptable and carries a smaller risk of ecological accidents. Since during the Ajka accident huge amounts of biologically available Al and moderate Cr(VI) concentrations were released into the terrestrial and aquatic environments, monitoring of Al and Cr(VI) set free during remedial actions at the contaminated site is essential. Particular care should be taken to minimize the risk of release of soluble Al species and Cr(VI) into water supplies and surface waters. Copyright © 2012 Elsevier B.V. All rights reserved.

  15. Field evaluation of in situ remediation of a heavy metal contaminated soil using lime and red-mud

    Energy Technology Data Exchange (ETDEWEB)

    Gray, C.W. [Agriculture and the Environment Division, Rothamsted Research, Harpenden, Herts AL5 2JQ (United Kingdom); Dunham, S.J. [Agriculture and the Environment Division, Rothamsted Research, Harpenden, Herts AL5 2JQ (United Kingdom); Dennis, P.G. [Agriculture and the Environment Division, Rothamsted Research, Harpenden, Herts AL5 2JQ (United Kingdom); Zhao, F.J. [Agriculture and the Environment Division, Rothamsted Research, Harpenden, Herts AL5 2JQ (United Kingdom); McGrath, S.P. [Agriculture and the Environment Division, Rothamsted Research, Harpenden, Herts AL5 2JQ (United Kingdom)]. E-mail: steve.mcgrath@bbsrc.ac.uk

    2006-08-15

    We evaluated the effectiveness of lime and red mud (by-product of aluminium manufacturing) to reduce metal availability to Festuca rubra and to allow re-vegetation on a highly contaminated brown-field site. Application of both lime and red mud (at 3 or 5%) increased soil pH and decreased metal availability. Festuca rubra failed to establish in the control plots, but grew to a near complete vegetative cover on the amended plots. The most effective treatment in decreasing grass metal concentrations in the first year was 5% red mud, but by year two all amendments were equally effective. In an additional pot experiment, P application in combination with red mud or lime decreased the Pb concentration, but not total uptake of Pb in Festuca rubra compared to red mud alone. The results show that both red mud and lime can be used to remediate a heavily contaminated acid soil to allow re-vegetation. - Red mud was effective in immobilising heavy metals in soil.

  16. Field evaluation of in situ remediation of a heavy metal contaminated soil using lime and red-mud

    International Nuclear Information System (INIS)

    Gray, C.W.; Dunham, S.J.; Dennis, P.G.; Zhao, F.J.; McGrath, S.P.

    2006-01-01

    We evaluated the effectiveness of lime and red mud (by-product of aluminium manufacturing) to reduce metal availability to Festuca rubra and to allow re-vegetation on a highly contaminated brown-field site. Application of both lime and red mud (at 3 or 5%) increased soil pH and decreased metal availability. Festuca rubra failed to establish in the control plots, but grew to a near complete vegetative cover on the amended plots. The most effective treatment in decreasing grass metal concentrations in the first year was 5% red mud, but by year two all amendments were equally effective. In an additional pot experiment, P application in combination with red mud or lime decreased the Pb concentration, but not total uptake of Pb in Festuca rubra compared to red mud alone. The results show that both red mud and lime can be used to remediate a heavily contaminated acid soil to allow re-vegetation. - Red mud was effective in immobilising heavy metals in soil

  17. Melting and Sintering of Ashes

    DEFF Research Database (Denmark)

    Hansen, Lone Aslaug

    1997-01-01

    -1300°C, and a trend of higher fusion temperatures with increasing contents of Al-silicates and quartz was found.c) Fly ashes, bottom ashes and deposits from coal/straw co-firing were all found to consist mainly of metal-alumina and alumina-silicates. These ashes all melt in the temperature range 1000......The thesis contains an experimental study of the fusion and sintering of ashes collected during straw and coal/straw co-firing.A laboratory technique for quantitative determination of ash fusion has been developed based on Simultaneous Thermal Analysis (STA). By means of this method the fraction......, the biggest deviations being found for salt rich (i.e. straw derived) ashes.A simple model assuming proportionality between fly ash fusion and deposit formation was found to be capable of ranking deposition rates for the different straw derived fly ashes, whereas for the fly ashes from coal/straw co-firing...

  18. Cholesterol Effect on Survival and Development of Larval Mud Crab Scylla serrata

    Directory of Open Access Journals (Sweden)

    MUHAMMAD AGUS SUPRAYUDI

    2012-03-01

    Full Text Available The effect of cholesterol on the survival and development of larval mud crab Scylla serrata were examined by feeding larvae with Artemia enriched with different level of cholesterol. Artemia enriched with four stated levels of cholesterol i.e., 0, 5, 10, and 20 ul/l (Chol 0, 5, 10, and 20. All treatments were mixed with DHA70G at 25 ul/l. All the oil was adjusted to 100 ul/l by adding the oleic acid. Survival rate, intermolt period, and carapace width at the fisrt crab stage of mud crab larvae fed Chol 0, 5, and 10 were higher compared to that of Chol 20 (P < 0.05. We suggest that free sterol contained in Artemia at 1.37% was harmful to the growth performance of mud crab larvae. This study suggests that mud crab larvae required at least 0.61% cholesterol for maintaining good survival and development and therefore no need to enrich Artemia by cholesterol for the practical purpose.

  19. Potential for timing high-energy marine inundation events in the recent geological past through age-dating of reef boulders in Fiji

    Science.gov (United States)

    Terry, James P.; Etienne, Samuel

    2014-12-01

    Transported coastal boulders have increasingly come to represent a valuable element of investigations within the broader framework of multi-proxy approaches applied to coastal hazard studies. Through a case study on Taveuni Island in Fiji, this paper outlines some approaches and hindrances to effective timing of prehistorical high-energy marine inundation events (storms and tsunamis) on tropical coastlines from the evidence of reef-platform carbonate boulders. Various sources of errors are outlined that investigators must consider when attempting to use carbonate boulder ages as a surrogate for timing past events. On Taveuni, uranium : thorium dates with a high level of precision (1-7 years) suggest that major inundation events have a return period of approximately 40-45 years since 1650 AD. Of particular importance, considerably different age dates are provided by coral samples sourced from the top and bottom (i.e. opposite faces) of individual boulders, so highlighting interpretation biases that must be avoided.

  20. Investigation on Leaching Behaviour of Fly Ash and Bottom Ash Replacement in Self-Compacting Concrete

    Science.gov (United States)

    Kadir, Aeslina Abdul; Ikhmal Haqeem Hassan, Mohd; Bakri Abdullah, Mohd Mustafa Al

    2016-06-01

    Fly ash and bottom ash are some of the waste generated by coal-fired power plants, which contains large quantities of toxic and heavy metals. In recent years, many researchers have been interested in studying on the properties of self-compacting concrete incorporated with fly ash and bottom ash but there was very limited research from the combination of fly ash and bottom ash towards the environmental needs. Therefore, this research was focused on investigating the leachability of heavy metals of SCC incorporated with fly ash and bottom ash by using Toxicity Characteristic Leaching Procedure, Synthetic Precipitation Leaching Procedure and Static Leaching Test. The samples obtained from the coal-fired power plant located at Peninsula, Malaysia. In this study, the potential heavy metals leached out from SCC that is produced with fly ash as a replacement for Ordinary Portland Cement and bottom ash as a substitute for sand with the ratios from 10% to 30% respectively were designated and cast. There are eight heavy metals of concern such as As, Cr, Pb, Zn, Cu, Ni, Mn and Fe. The results indicated that most of the heavy metals leached below the permissible limits from the United States Environmental Protection Agency and World Health Organization limit for drinking water. As a conclusion, the minimum leaching of the heavy metals from the incorporation of fly ash and bottom ash in self-compacting concrete was found in 20% of fly ash and 20% of bottom ash replacement. The results also indicate that this incorporation could minimize the potential of environmental problems.

  1. Processed bottom ash for replacing fine aggregate in making high-volume fly ash concrete

    Directory of Open Access Journals (Sweden)

    Antoni

    2017-01-01

    Full Text Available Bottom ash is a coal plant by-product that is abundant and underutilized. There is the potential use of bottom ash as a fine aggregate replacement in concrete mixtures; however, the problems of water absorption and uniformity of quality of the material need to be overcome first. In this study, bottom ash was treated by sieve separation and pounding to smaller particle size for use as a sand substitute. The physical and chemical characteristics of bottom ash were tested after treatment including water absorption, sieve analysis, and fineness modulus. Highvolume fly ash (HVFA mortar specimens were made and the compressive strength and flowability test using bottom ash after treatment are compared with that of the sand specimen. Low water to cementitious ratio was used to ensure higher strength from the cementitious paste and superplasticizer demand was determined for each treatment. The result showed that bottom ash can be used as fine aggregate replacement material. Sieve separation of the bottom ash could produce 75% of the compressive strength compared with the control sand specimen, whereas pounded bottom ash could have up to 96% of the compressive strength of the control specimen. A 28-day compressive strength of 45 MPa was achievable with 100% replacement of fine aggregate with bottom ash.

  2. Sequential extraction applied to Peruibe black mud, SP, Brazil

    International Nuclear Information System (INIS)

    Torrecilha, Jefferson Koyaishi

    2014-01-01

    The Peruibe Black mud is used in therapeutic treatments such as psoriasis, peripheral dermatitis, acne and seborrhoea, as well as in the treatment of myalgia, arthritis, rheumatism and non-articular processes. Likewise other medicinal clays, it may not be free from possible adverse health effects due to possible hazardous minerals leading to respiratory system occurrences and other effects, caused by the presence of toxic elements. Once used for therapeutic purposes, any given material should be fully characterized and thus samples of Peruibe black mud were analyzed to determine physical and chemical properties: moisture content, organic matter and loss on ignition; pH, particle size, cation exchange capacity and swelling index. The elemental composition was determined by Neutron Activation Analysis, Atomic Absorption Graphite Furnace and X-ray fluorescence; the mineralogical composition was determined by X-ray diffraction. Another tool widely used to evaluate the behavior of trace elements, in various environmental matrices, is the sequential extraction. Thus, a sequential extraction procedure was applied to fractionate the mud in specific geochemical forms and verify how and how much of the elements may be contained in it. Considering the several sequential extraction procedures, BCR-701 method (Community Bureau of Reference) was used since it is considered the most reproducible among them. A simple extraction with an artificial sweat was, also, applied in order to verify which components are potentially available for absorption by the patient skin during the topical treatment. The results indicated that the mud is basically composed by a silty-clay material, rich in organic matter and with good cation exchange capacity. There were no significant variations in mineralogy and elemental composition of both, in natura and mature mud forms. The analysis by sequential extraction and by simple extraction indicated that the elements possibly available in larger

  3. A nonlinear model for the fluidization of marine mud by waves

    Energy Technology Data Exchange (ETDEWEB)

    Foda, M.A.; Hunt, J.R.; Chou, Hsien-Ter (Univ. of California, Berkeley (United States))

    1993-04-15

    The authors consider the problem of fluidization of mud deposits in shallow waters due to interactions with water waves. This is of increasing interest because of concerns that water pollutants, including heavy metals, pesticides, etc., are often found near surfaces of mud deposits. The authors look at the question of whether the cohesive properties of mud deposits exhibit nonlinear properties when they experience strains from water wave interactions. It is obvious that with large enough wave interactions the deposits become fluidized, and are not in that case truly nonlinear. In their modeling efforts they try to incorporate these ideas into a cohesive model where the magnitude of the water wave-sediment interaction has an influence on the type of response within the system.

  4. Mechanism of red mud combined with Fenton's reagent in sewage sludge conditioning.

    Science.gov (United States)

    Zhang, Hao; Yang, Jiakuan; Yu, Wenbo; Luo, Sen; Peng, Li; Shen, Xingxing; Shi, Yafei; Zhang, Shinan; Song, Jian; Ye, Nan; Li, Ye; Yang, Changzhu; Liang, Sha

    2014-08-01

    Red mud was evaluated as an alternative skeleton builder combined with Fenton's reagent in sewage sludge conditioning. The results show that red mud combined with Fenton's reagent showed good conditioning capability with the pH of the filtrate close to neutrality, indicating that red mud acted as a neutralizer as well as a skeleton builder when jointly used with Fenton's reagent. Through response surface methodology (RSM), the optimal dosages of Fe(2+), H2O2 and red mud were proposed as 31.9, 33.7 and 275.1 mg/g DS (dry solids), respectively. The mechanism of the composite conditioner could be illuminated as follows: (1) extracellular polymeric substances (EPS), including loosely bound EPS and tightly bound EPS, were degraded into dissolved organics, e.g., proteins and polysaccharides; (2) bound water was released and converted into free water due to the degradation of EPS; and (3) morphology of the conditioned sludge exhibited a porous structure in contrast with the compact structure of raw sludge, and the addition of red mud formed new mineral phases and a rigid lattice structure in sludge, allowing the outflow of free water. Thus, sludge dewatering performance was effectively improved. The economic assessment for a wastewater treatment plant of 370,000 equivalent inhabitants confirms that using red mud conditioning, combined with Fenton's reagent, leads to a saving of approximately 411,000 USD/y or 50.8 USD/t DS comparing with using lime and ordinary Portland cement combined with Fenton's reagent, and approximately 612,000 USD/y or 75.5 USD/t DS comparing with the traditional treatment. Copyright © 2014 Elsevier Ltd. All rights reserved.

  5. Propagation of Measurement-While-Drilling Mud Pulse during High Temperature Deep Well Drilling Operations

    OpenAIRE

    Li, Hongtao; Meng, Yingfeng; Li, Gao; Wei, Na; Liu, Jiajie; Ma, Xiao; Duan, Mubai; Gu, Siman; Zhu, Kuanliang; Xu, Xiaofeng

    2013-01-01

    Signal attenuates while Measurement-While-Drilling (MWD) mud pulse is transmited in drill string during high temperature deep well drilling. In this work, an analytical model for the propagation of mud pulse was presented. The model consists of continuity, momentum, and state equations with analytical solutions based on the linear perturbation analysis. The model can predict the wave speed and attenuation coefficient of mud pulse. The calculated results were compared with the experimental dat...

  6. Effect of formulation variables on the physical properties and stability of Dead Sea mud masks.

    Science.gov (United States)

    Shahin, Sawsan; Hamed, Saja; Alkhatib, Hatim S

    2015-01-01

    The physical stability of Dead Sea mud mask formulations under different conditions and their rheological properties were evaluated as a function of the type and level of thickeners, level of the humectant, incorporation of ethanol, and mode of mud treatment. Formulations were evaluated in terms of visual appearance, pH, moisture content, spreadability, extrudability, separation, rate of drying at 32 degrees C, and rheological properties. Prepared mud formulations and over-the-shelf products showed viscoplastic shear thinning behavior; satisfactory rheological behavior was observed with formulations containing a total concentration of thickeners less than 10% (w/w). Casson and Herschel-Bulkley models were found the most suitable to describe the rheological data of the prepared formulations. Thickener incorporation decreased phase separation and improved formulation stability. Bentonite incorporation in the mud prevented color changes during stability studies while glycerin improved spreadability. Addition of 5% (w/w) ethanol improved mud extrudability, slightly increased percent separation, accelerated drying at 32 degrees C, and decreased viscosity and yield stress values. Different mud treatment techniques did not cause a clear behavioral change in the final mud preparation. B10G and K5B5G were labeled as "best formulas" based on having satisfactory physical and aesthetic criteria investigated in this study, while other formulations failed in one or more of the tests we have performed.

  7. Ash fusion temperatures and the transformations of coal ash particles to slag

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, S.K.; Wall, T.F.; Creelman, R.A.; Gupta, R.P. [University of Newcastle, Newcastle, NSW (Australia). CRC for Black Coal Utilisation

    1998-07-01

    A mechanistic study is detailed in which coal ash is heated with its shrinkage measured continuously up to a temperature of 1600{degree}C. The temperature corresponding to the rapid rate of shrinkage correspond to the formation of eutectics identified on phase diagrams. Samples were therefore heated to these temperatures, cooled rapidly and examined using a scanning electron microscope (SEM) to identify the associated chemical and physical changes. The progressive changes in the range of chemical composition (from SEM), the extent of undissolved ash particles and porosity were then quantified and related to homogenisation, viscosity and ash fusion mechanisms. Alternate ash fusion temperatures based on different levels of shrinkage have also been suggested to characterise the ash deposition tendency of the coals. 13 refs., 9 figs.

  8. Interspecific proteomic comparisons reveal ash phloem genes potentially involved in constitutive resistance to the emerald ash borer.

    Science.gov (United States)

    Whitehill, Justin G A; Popova-Butler, Alexandra; Green-Church, Kari B; Koch, Jennifer L; Herms, Daniel A; Bonello, Pierluigi

    2011-01-01

    The emerald ash borer (Agrilus planipennis) is an invasive wood-boring beetle that has killed millions of ash trees since its accidental introduction to North America. All North American ash species (Fraxinus spp.) that emerald ash borer has encountered so far are susceptible, while an Asian species, Manchurian ash (F. mandshurica), which shares an evolutionary history with emerald ash borer, is resistant. Phylogenetic evidence places North American black ash (F. nigra) and Manchurian ash in the same clade and section, yet black ash is highly susceptible to the emerald ash borer. This contrast provides an opportunity to compare the genetic traits of the two species and identify those with a potential role in defense/resistance. We used Difference Gel Electrophoresis (DIGE) to compare the phloem proteomes of resistant Manchurian to susceptible black, green, and white ash. Differentially expressed proteins associated with the resistant Manchurian ash when compared to the susceptible ash species were identified using nano-LC-MS/MS and putative identities assigned. Proteomic differences were strongly associated with the phylogenetic relationships among the four species. Proteins identified in Manchurian ash potentially associated with its resistance to emerald ash borer include a PR-10 protein, an aspartic protease, a phenylcoumaran benzylic ether reductase (PCBER), and a thylakoid-bound ascorbate peroxidase. Discovery of resistance-related proteins in Asian species will inform approaches in which resistance genes can be introgressed into North American ash species. The generation of resistant North American ash genotypes can be used in forest ecosystem restoration and urban plantings following the wake of the emerald ash borer invasion.

  9. Survival Times of Meter-Sized Rock Boulders on the Surface of Airless Bodies

    Science.gov (United States)

    Basilevsky, A. T.; Head, J. W.; Horz, F.; Ramsley, K.

    2015-01-01

    This study considers the survival times of meter-sized rock boulders on the surfaces of several airless bodies. As the starting point, we employ estimates of the survival times of such boulders on the surface of the Moon by[1], then discuss the role of destruction due to day-night temperature cycling, consider the meteorite bombardment environment on the considered bodies in terms of projectile flux and velocities and finally estimate the survival times. Survival times of meter-sized rocks on lunar surface: The survival times of hand specimen-sized rocks exposed to the lunar surface environment were estimated based on experiments modeling the destruction of rocks by meteorite impacts, combined with measurements of the lunar surface meteorite flux, (e.g.,[2]). For estimations of the survival times of meter-sized lunar boulders, [1] suggested a different approach based on analysis of the spatial density of boulders on the rims of small lunar craters of known absolute age. It was found that for a few million years, only a small fraction of the boulders ejected by cratering process are destroyed, for several tens of million years approx.50% are destroyed, and for 200-300 Ma, 90 to 99% are destroyed. Following [2] and other works, [1] considered that the rocks are mostly destroyed by meteorite impacts. Destruction of rocks by thermal-stress. However, high diurnal temperature variations on the surface of the Moon and other airless bodies imply that thermal stresses may also be a cause of surface rock destruction. Delbo et al. [3] interpreted the observed presence of fine debris on the surface of small asteroids as due to thermal surface cycling. They stated that because of the very low gravity on the surface of these bodies, ejecta from meteorite impacts should leave the body, so formation there of fine debris has to be due to thermal cycling. Based on experiments on heating-cooling of cm-scale pieces of ordinary and carbonaceous chondrites and theoretical modeling of

  10. Toxicity of invert drilling muds composted with wood/bark chips

    Energy Technology Data Exchange (ETDEWEB)

    Bessie, K. [EBA Engineering Consultants Ltd., Calgary, AB (Canada)

    2006-07-01

    Since the early to mid 1990s, many companies have composted invert (diesel) drilling muds with wood chips/bark chips in the green (forestry) zone as a method of drilling mud treatment. This presentation addressed the toxicity of invert drilling muds composted with wood/bark chips and provided some background on composted invert drilling mud (CIDM). EBA Engineering monitored 22 third-party sites in 2002, some of which were biopiles, and others land treatment areas (LTAs). Active treatment started between 1995 and 1999 and some LTAs were seeded with varying degrees of success. Composted materials had hydrocarbon odour and staining and were very moist. Materials exceeded Alberta Environment guidelines for petroleum hydrocarbons (PHCs) and sometimes barium. Most sites were within areas that had forestry production/wildlife as end land use. Receptors included plants, soil invertebrates by soil contact, and wildlife by ingestion. Stakeholder meetings were held for their input and an ecotoxicity study was developed. Material tested, tests and species used as well as results of the ecotoxicity study were presented. A comparison of results to other EBA composting studies was also given. It was concluded that CIDM affects the reproduction of earthworms and springtails, and plant growth; wood/barks chips themselves can be ecotoxic; and, other compost studies with finely ground sawdust and no bark chips had less ecotoxicity. tabs., figs.

  11. Removal of fluoride ions from aqueous solution by waste mud

    International Nuclear Information System (INIS)

    Kemer, Baris; Ozdes, Duygu; Gundogdu, Ali; Bulut, Volkan N.; Duran, Celal; Soylak, Mustafa

    2009-01-01

    The present study was carried out to assess the ability of original waste mud (o-WM) and different types of activated waste mud which are acid-activated (a-WM) and precipitated waste mud (p-WM), in order to remove excess of fluoride from aqueous solution by using batch technique. The p-WM exhibited greater performance than the others. Adsorption studies were conducted as a function of pH, contact time, initial fluoride concentration, adsorbent concentration, temperature, etc. Studies were also performed to understand the effect of some co-existing ions present in aqueous solutions. Adsorption process was found to be almost independent of pH for all types of waste mud. Among the kinetic models tested for p-WM, pseudo-second-order model fitted the kinetic data well with a perfect correlation coefficient value of 1.00. It was found that the adequate time for the adsorption equilibrium of fluoride was only 1 h. Thermodynamic parameters including the Gibbs free energy (ΔG o ), enthalpy (ΔH o ), and entropy (ΔS o ) revealed that adsorption of fluoride ions on the p-WM was feasible, spontaneous and endothermic in the temperature range of 0-40 deg. C. Experimental data showed a good fit with the Langmuir and Freundlich adsorption isotherm models. Results of this study demonstrated the effectiveness and feasibility of WM for removal of fluoride ions from aqueous solution.

  12. OPTIMIZATION OF MUD HAMMER DRILLING PERFORMANCE - A PROGRAM TO BENCHMARK THE VIABILITY OF ADVANCED MUD HAMMER DRILLING

    Energy Technology Data Exchange (ETDEWEB)

    Alan Black; Arnis Judzis

    2003-01-01

    Progress during current reporting year 2002 by quarter--Progress during Q1 2002: (1) In accordance to Task 7.0 (D. No.2 Technical Publications) TerraTek, NETL, and the Industry Contributors successfully presented a paper detailing Phase 1 testing results at the February 2002 IADC/SPE Drilling Conference, a prestigious venue for presenting DOE and private sector drilling technology advances. The full reference is as follows: IADC/SPE 74540 ''World's First Benchmarking of Drilling Mud Hammer Performance at Depth Conditions'' authored by Gordon A. Tibbitts, TerraTek; Roy C. Long, US Department of Energy, Brian E. Miller, BP America, Inc.; Arnis Judzis, TerraTek; and Alan D. Black, TerraTek. Gordon Tibbitts, TerraTek, will presented the well-attended paper in February of 2002. The full text of the Mud Hammer paper was included in the last quarterly report. (2) The Phase 2 project planning meeting (Task 6) was held at ExxonMobil's Houston Greenspoint offices on February 22, 2002. In attendance were representatives from TerraTek, DOE, BP, ExxonMobil, PDVSA, Novatek, and SDS Digger Tools. (3) PDVSA has joined the advisory board to this DOE mud hammer project. PDVSA's commitment of cash and in-kind contributions were reported during the last quarter. (4) Strong Industry support remains for the DOE project. Both Andergauge and Smith Tools have expressed an interest in participating in the ''optimization'' phase of the program. The potential for increased testing with additional Industry cash support was discussed at the planning meeting in February 2002. Progress during Q2 2002: (1) Presentation material was provided to the DOE/NETL project manager (Dr. John Rogers) for the DOE exhibit at the 2002 Offshore Technology Conference. (2) Two meeting at Smith International and one at Andergauge in Houston were held to investigate their interest in joining the Mud Hammer Performance study. (3) SDS Digger Tools (Task 3

  13. Evaluation of the hurricanes Gustav and Ike impact on healing mud from San Diego River using nuclear and geochemical techniques

    International Nuclear Information System (INIS)

    Diaz Rizo, Oscar; Gelen Rudnikas, Alina Katia; Rodriguez, D'Alessandro; Arado Lopez, Juana O.; Dominguez Rodriguez, Roberto; Gonzalez Hernandez, Patricia; Melian Rodriguez, Clara M.; Suarez Munnoz, Margaret; Fagundo Castillo, Juan R.; Blanco Padilla, Dagoberto

    2011-01-01

    Effects induced by the hurricanes Gustav and Ike on San Diego River mud characteristics have been studied. X-ray fluorescence analysis, gamma spectrometry and measurement of some physico-chemical characteristics in mud samples, collected before and after hurricane impacts, shows that hurricanes induced changes in mud major composition and in some other mud characteristics. The average sedimentation rate determined by gamma spectrometry in San Diego River outlet permitted to estimate that the original mud characteristics will be recovered never before than 5-7 years. Further studies of the influence of mud characteristics changes due the hurricanes impact in mud therapeutic properties are recommended.(author)

  14. Selection of parameters for mud pumps used for HDD Systems

    Directory of Open Access Journals (Sweden)

    Jan Ziaja

    2006-10-01

    Full Text Available Design solutions of rigs used for HDD are presented in the paper. HDD devices are classified on the basis of presented criteria, and then a division of rigs was proposed. The principles of determining technological parameters of piston mud pumps for HDD are presented. The principles of determining volume flow rate for an arbitrary rheological model of drilling mud are discussed. The dependences enabling a calculation of resistance of drilling fluid flow in a circulation system are also presented.

  15. Sulfur Fixation by Chemically Modified Red Mud Samples Containing Inorganic Additives: A Parametric Study

    Directory of Open Access Journals (Sweden)

    Yang Liu

    2016-01-01

    Full Text Available Sulfur retention ability of Bayer red mud from alumina plant was investigated. Bayer red mud modified by fusel salt and waste mother liquor of sodium ferrocyanide as the main sulfur fixation agent and the calcium based natural mineral materials as servicing additives; the experimental results showed the following: (1 Through 10 wt% waste mother liquor of sodium ferrocyanide modifying Bayer red mud, sulfur fixation rate can increase by 13 wt%. (2 Magnesium oxide can obviously improve the sulfur fixation performance of Bayer red mud and up to a maximum sulfur fixation rate of 47 wt% at adding 1 wt% magnesium oxide. (3 Dolomite enhanced the sulfur fixation performances with the sulfur fixation rate of 68 wt% in optimized condition. (4 Vermiculite dust reduced sulfur dioxide during the fixed-sulfur process of modified Bayer red mud, and the desulphurization ration could reach up to a maximum 76 wt% at 950°C. (5 An advanced three-component sulfur fixation agent was investigated, in which the optimized mass ratio of modified Bayer red mud, dolomite, and vermiculite dust was 70 : 28 : 2 in order, and its sulfur fixation efficiency has reached to a maximum 87 wt% under its 20 wt% dosage in the coal.

  16. A comparative study of modern carbonate mud in reefs and carbonate platforms: Mostly biogenic, some precipitated

    Science.gov (United States)

    Gischler, Eberhard; Dietrich, Sarah; Harris, Daniel; Webster, Jody M.; Ginsburg, Robert N.

    2013-06-01

    Carbonate mud from reefs and carbonate platforms in six locations of the Atlantic, Indian, and Pacific Oceans (Belize, Bahamas, Florida, the Maldives, French Polynesia, Great Barrier Reef) was systematically and quantitatively analyzed with regard to texture, composition, mineralogy, and geochemistry. Mud composition shows considerable variability, however, the data supports the contention that these muds are largely derived from the breakdown of skeletal grains and codiacean algae. Only mud from the Bahamas and northern Belize, areas which are characterized by common whitings, is interpreted to be mainly inorganically precipitated. Three grain-size fractions (63-20 μm, 20-4 μm, aragonite needles, nanograins, and coccoliths. Coccoliths are common in deeper lagoonal settings of the open ocean settings (Maldives, French Polynesia). The geochemistry of the aragonite contents and strontium concentrations, suggesting physico-chemical precipitation. The northern Belize and Great Barrier Reef samples show the highest magnesium calcite values and, accordingly, produced the lowest aragonite and strontium measurements. The high-magnesium calcite portion of the northern Belize mud is either precipitated or due to abundant micritized skeletal grains (e.g., foraminifera): more studies are needed to verify the origin. In the case of the Great Barrier Reef sample, coralline algae appear to be the source of abundant high-magnesium calcite. This study emphasizes that from a global perspective, modern muds in reefs and carbonate platforms exhibit different compositions but are in many cases biologically derived. Even though the composition of modern carbonate muds varies among the six locations investigated, they may serve as analogs for the formation of muds in Cenozoic and Mesozoic reefs and carbonate platforms. Limitations of the interpretation of carbonate-mud origin include the difficulty of identifying, quantifying, and analyzing small grains, the ease with which small

  17. ADULT COHO SALMON AND STEELHEAD USE OF BOULDER WEIRS IN SOUTHWEST OREGON STREAMS

    Science.gov (United States)

    The placement of log and boulder structures in streams is a common and often effective technique for improving juvenile salmonid rearing habitat and increasing fish densities. Less frequently examined has been the use of these structures by adult salmonids. In 2004, spawner densi...

  18. Characteristics of laser textured silicon surface and effect of mud adhesion on hydrophobicity

    Energy Technology Data Exchange (ETDEWEB)

    Yilbas, B.S., E-mail: bsyilbas@kfupm.edu.sa [ME Department, King Fahd University of Petroleum & Minerals, Kfupm box 1913, Dhahran 31261 (Saudi Arabia); Ali, H. [ME Department, King Fahd University of Petroleum & Minerals, Kfupm box 1913, Dhahran 31261 (Saudi Arabia); Khaled, M. [CHEM Department, King Fahd University of Petroleum & Minerals, Dhahran (Saudi Arabia); Al-Aqeeli, N.; Abu-Dheir, N. [ME Department, King Fahd University of Petroleum & Minerals, Kfupm box 1913, Dhahran 31261 (Saudi Arabia); Varanasi, K.K. [Mechanical Engineering, Massachusetts Institute of Technology, Boston, MA (United States)

    2015-10-01

    Highlights: • Laser treatment increases surface microhardness and slightly lowers surface fracture toughness. • Residual stress formed is compressive and self-annealing effect of laser tracks lowers residual stress. • Nitride species lowers surface energy and adhesion work required to remove dust. • Mud residues do not have notable effect on fracture toughness and microhardness of treated surface. • Mud residues lower surface hydrophobicity. - Abstract: Laser gas assisted texturing of silicon wafer surface is carried out. Morphological and metallurgical changes in the treated layer are examined using the analytical tools. Microhardness and fracture toughness of the laser treated surface are measured using the indentation technique while residual stress formed is determined from the X-ray diffraction data. The hydrophobicity of the textured surfaces are assessed incorporating the contact angle data and compared with those of as received workpiece surfaces. Environmental dust accumulation and mud formation, due to air humidity, at the laser treated and as received workpiece surfaces are simulated and the effect of the mud residues on the properties of the laser treated surface are studied. The adhesion work due to the presence of the mud on the laser treated surface is also measured. It is found that laser textured surface composes of micro/nano poles and fibers, which in turn improves the surface hydrophobicity significantly. In addition, formation of nitride species contributes to microhardness increase and enhancement of surface hydrophobicity due to their low surface energy. The mud residues do not influence the fracture toughness and microhardness of the laser textured surface; however, they reduced the surface hydrophobicity significantly.

  19. Cellular immune responses and phagocytic activity of fishes exposed to pollution of volcano mud.

    Science.gov (United States)

    Risjani, Yenny; Yunianta; Couteau, Jerome; Minier, Christophe

    2014-05-01

    Since May 29, 2006, a mud volcano in the Brantas Delta of the Sidoarjo district has emitted mud that has inundated nearby villages. Pollution in this area has been implicated in detrimental effects on fish health. In fishes, leukocyte and phagocytic cells play a vital role in body defenses. We report for the first time the effect of "LUSI" volcano mud on the immune systems of fish in the Brantas Delta. The aim of this study was to find biomarkers to allow the evaluation of the effects of volcanic mud and anthropogenic pollution on fish health in the Brantas Delta. The study took places at the Brantas Delta, which was polluted by volcano mud, and at reference sites in Karangkates and Pasuruan. Leukocyte numbers were determined using a Neubauer hemocytometer and a light microscope. Differential leukocyte counts were determined using blood smears stained with May Grunwald-Giemsa, providing neutrophil, lymphocyte and monocyte counts. Macrophages were taken from fish kidney, and their phagocytic activity was measured. In vitro analyses revealed that leukocyte and differential leukocyte counts (DLC) were higher in Channa striata and Chanos chanos caught from the polluted area. Macrophage numbers were higher in Oreochromis mossambicus than in the other species, indicating that this species is more sensitive to pollution. In areas close to volcanic mud eruption, all specimens had lower phagocytic activity. Our results show that immune cells were changed and phagocytic activity was reduced in the polluted area indicating cytotoxicity and alteration of the innate immune system in fishes exposed to LUSI volcano mud and anthropogenic pollution. Copyright © 2014 Elsevier Ltd. All rights reserved.

  20. Survey for tolerance to emerald ash borer within North American ash species

    Science.gov (United States)

    Jennifer L. Koch; Mary E. Mason; David W. Carey; Kathleen Knight; Therese Poland; Daniel A. Herms

    2010-01-01

    Since the discovery of the emerald ash borer (EAB) near Detroit, MI, in 2002, more than 40 million ash trees have been killed and another 7.5 billion are at risk in the United States. When the EAB outbreak was initially discovered, our native ash species appeared to have no resistance to the pest.

  1. Cast-concrete products made with FBC ash and wet-collected coal-ash

    Energy Technology Data Exchange (ETDEWEB)

    Naik, T.R.; Kraus, R.N.; Chun, Y.M.; Botha, F.D. [University of Wisconsin, Milwaukee, WI (United States)

    2005-12-01

    Cast-concrete hollow blocks, solid blocks, and paving stones were produced at a manufacturing plant by replacing up to 45% (by mass) of portland cement with fluidized bed combustion (FBC) coal ash and up to 9% of natural aggregates with wet-collected, low-lime, coarse coal-ash (WA). Cast-concrete product specimens of all three types exceeded the compressive strength requirements of ASTM from early ages, with the exception of one paving-stone mixture, which fell short of the requirement by less than 10%. The cast-concrete products made by replacing up to 40% of cement with FBC ash were equivalent in strength (89-113% of control) to the products without ash. The abrasion resistance of paving stones was equivalent for up to 34% FBC ash content. Partial replacement of aggregates with WA decreased strength of the products. The resistance of hollow blocks and paving stones to freezing and thawing decreased appreciably with increasing ash contents. The cast-concrete products could be used indoors in regions where freezing and thawing is a concern, and outdoors in a moderate climate.

  2. Environmental control of drilling mud discharge through dewatering in cold weather climates

    International Nuclear Information System (INIS)

    Wojtanowicz, A.K.

    1991-01-01

    The paper presents results of an experimental study into the effect of drilling mud temperature upon the dewatering performance. Three temperature ranges were considered: from flowline temperature to room temperature, from room temperature to freezing point, and the freeze (4 degrees F)/thaw (54 degrees F) cycle. The tested drilling fluids included unweighted and weighted fresh water muds and a weighted salt water mud. a sealed laboratory batch reactor was used in the experiments to prevent rapid vaporization of separated water at temperatures above 140 degrees F. Also, ice or ice-salt baths were utilized for deep freezing. The dewaterability (net water removal) was measured with a bench-top plate press under constant expression pressure 30 psi

  3. Evolution and phylogeny of the mud shrimps (Crustacea: Decapoda) revealed from complete mitochondrial genomes.

    Science.gov (United States)

    Lin, Feng-Jiau; Liu, Yuan; Sha, Zhongli; Tsang, Ling Ming; Chu, Ka Hou; Chan, Tin-Yam; Liu, Ruiyu; Cui, Zhaoxia

    2012-11-16

    The evolutionary history and relationships of the mud shrimps (Crustacea: Decapoda: Gebiidea and Axiidea) are contentious, with previous attempts revealing mixed results. The mud shrimps were once classified in the infraorder Thalassinidea. Recent molecular phylogenetic analyses, however, suggest separation of the group into two individual infraorders, Gebiidea and Axiidea. Mitochondrial (mt) genome sequence and structure can be especially powerful in resolving higher systematic relationships that may offer new insights into the phylogeny of the mud shrimps and the other decapod infraorders, and test the hypothesis of dividing the mud shrimps into two infraorders. We present the complete mitochondrial genome sequences of five mud shrimps, Austinogebia edulis, Upogebia major, Thalassina kelanang (Gebiidea), Nihonotrypaea thermophilus and Neaxius glyptocercus (Axiidea). All five genomes encode a standard set of 13 protein-coding genes, two ribosomal RNA genes, 22 transfer RNA genes and a putative control region. Except for T. kelanang, mud shrimp mitochondrial genomes exhibited rearrangements and novel patterns compared to the pancrustacean ground pattern. Each of the two Gebiidea species (A. edulis and U. major) and two Axiidea species (N. glyptocercus and N. thermophiles) share unique gene order specific to their infraorders and analyses further suggest these two derived gene orders have evolved independently. Phylogenetic analyses based on the concatenated nucleotide and amino acid sequences of 13 protein-coding genes indicate the possible polyphyly of mud shrimps, supporting the division of the group into two infraorders. However, the infraordinal relationships among the Gebiidea and Axiidea, and other reptants are poorly resolved. The inclusion of mt genome from more taxa, in particular the reptant infraorders Polychelida and Glypheidea is required in further analysis. Phylogenetic analyses on the mt genome sequences and the distinct gene orders provide further

  4. Production of Green Steel from Red Mud: A Novel Concept

    Science.gov (United States)

    Bhoi, Bhagyadhar; Behera, Pravas Ranjan; Mishra, Chitta Ranjan

    Red mud of Indian origin contains around 55% plus of Fe2O3 and is considered as a hazardous waste for the alumina industry. For production of one tone of alumina employing the Bayer's Process, around two tones of red mud is generated from three tones of Bauxite. Conventional process of steel making is not devoid of environmental pollution. In the present investigation, efforts have been made to produce steel from red mud by adopting reduction roasting, magnetic separation and hydrogen plasma smelting route. Magnetic fraction, containing enriched iron oxide and minimal content of alumina, is produced following the first two stages which is then subjected to hydrogen plasma smelting process for production of steel. This novel concept follows a green path way for production of steel free from pollution and is termed as green steel. Further, the only by-product that is produced in the process, is water, which is eco-friendly and recyclable.

  5. Effects of Red-mud and Organic Fertilizer on Cadmium and Lead Absorption and Distribution in Rice

    Directory of Open Access Journals (Sweden)

    FANG Ya-yu

    2016-09-01

    Full Text Available Effects of red mud and organic fertilizer on distribution of cadmium(Cd and lead (Pb in soil-rice system were studied in field by orthogonal test. Results showed that after red mud and organic fertilizer added including single and combined, the soil pH value increased 0.36~1.90 units, contents of Cd and Pb in rice rhizosphere soil decreased 2.73%~26.25% and 7.15%~34.26% respectively and contents of Cd and Pb in brown rice decreased 23.24%~55.90% and 11.76%~29.41% respectively. In all treatments, single red mud was best, followed by red mud and organic fertilizer combined, single organic fertilizer was worst. The content of Cd and Pb in different rice organs with addition of red mud and organic fertilizer decreased significantly, the contribution rate of Cd and Pb at different stages changed obviously, and influences of adding quantity and fertilizing method were also significant. Different treatments had different effects on contents of Cd and Pb in brown rice. Compared with CK, red mud (4 000 kg·hm-2 was the best for Cd, combination of red mud (4 000 kg·hm-2 and organic fertilizer (1 000 kg·hm-2was the best for Pb, the contents of which were 55.90% and 29.41% less than the control respectively. Although contents of Cd and Pb in brown rice decreased significantly after red mud and organic fertilizer added, contents of Cd and Pb in brown rice were still higher than national food safety standards (GB 2762-2012 because of high polluted degree of Cd (65 times than standard and Pb(7 times than standard in soil. All results showed it was ineffective to control heavy metal pollution in brown rice only by red mud and organic fertilizer addition in high polluted degree soils.

  6. Can ash clog soil pores?

    Science.gov (United States)

    Stoof, Cathelijne; Stoof, Cathelijne; Gevaert, Anouk; Gevaert, Anouk; Baver, Christine; Baver, Christine; Hassanpour, Bahareh; Hassanpour, Bahareh; Morales, Veronica; Morales, Veronica; Zhang, Wei; Zhang, Wei; Martin, Deborah; Martin, Deborah; Steenhuis, Tammo; Steenhuis, Tammo

    2015-04-01

    Wildfire can greatly increase a landscape's vulnerability to flooding and erosion events, and ash is thought to play a large role in controlling runoff and erosion processes after wildfire. Although ash can store rainfall and thereby reduce runoff and erosion for a limited period after wildfires, it has also been hypothesized to clog soil pores and reduce infiltration. Several researchers have attributed the commonly observed increase in runoff and erosion after fire to the potential pore-clogging effect of ash. Evidence is however incomplete, as to date, research has solely focused on identifying the presence of ash in the soil, with the actual flow processes associated with the infiltration and pore-clogging of ash remaining a major unknown. In several laboratory experiments, we tested the hypothesis that ash causes pore clogging to the point that infiltration is hampered and ponding occurs. We first visualized and quantified pore-scale infiltration of water and ash in sand of a range of textures and at various infiltration rates, using a digital bright field microscope capturing both photo and video. While these visualization experiments confirm field and lab observation of ash washing into soil pores, we did not observe any clogging of pores, and have not been able to create conditions for which this does occur. Additional electrochemical analysis and measurement of saturated hydraulic conductivity indicate that pore clogging by ash is not plausible. Electrochemical analysis showed that ash and sand are both negatively charged, showing that attachment of ash to sand and any resulting clogging is unlikely. Ash also had quite high saturated conductivity, and systems where ash was mixed in or lying on top of sand had similarly high hydraulic conductivity. Based on these various experiments, we cannot confirm the hypothesis that pore clogging by ash contributes to the frequently observed increase in post-fire runoff, at least for the medium to coarse sands

  7. Influence of drilling muds on the primary chemosensory neurons in walking legs of the lobster, Homarus americanus

    Energy Technology Data Exchange (ETDEWEB)

    Derby, C D; Atema, J

    1981-01-01

    The effects of whole drilling muds on the normal activity of walking leg chemosensory neurons of the lobster, Homarus americanus, were examined using extracellular neurophysiological recording techniques. Exposure of legs for 3-5 min to 10 mg/L drilling mud suspended in seawater altered responses to food odors of 29% of the chemoreceptors examined (data pooled for the two drilling muds tested); similar exposure to 100 mg/L drilling mud resulted in interference with 44% of all receptors studied. The effects of both of these concentrations are statistically significant, although they are not different from each other. Interference was usually manifested as a marked reduction in the number of action potentials in a response. In one preparation, the exposure to drilling mud caused a change in the temporal pattern of the spikes without affecting the total number of spikes. Other chemosensory neurons were excited by 10 mg/L drilling mud itself. However, not all chemoreceptors are inhibited by these drilling muds since responses to feeding stimuli were recorded from the legs of lobsters that had been exposed to drilling mud for 4-8 d before the neurophysiological experiments. Antennular and leg chemoreceptors are important in eliciting normal feeding behavior in lobsters. Although behavioral assays have demonstrated that feeding behavior is altered following exposure to drilling muds and petroleum fractions, there is no conclusive proof for a causal relationship between chemoreceptor interference and behavior deficits. The two techniques complement each other as pollution detection assays, perhaps reflecting a common interference mechanism. 42 references, 4 figures, 2 tables.

  8. Fission track ages on apatite of Bergell rocks from central Alps and Bergell boulders in Oligocene sediments

    International Nuclear Information System (INIS)

    Wagner, G.A.; Miller, D.S.

    1979-01-01

    Previous radiometric dating studies indicated that the Bergell region, in contrast to other regions of the Central Alps, experienced an early, rapid uplift, but with decreasing rate. Furthermore, there is also a geological record of the early uplift history of the Bergell granite by the existence of boulders which were derived from this granite and which occur in the Late Oligocene sediments of the Po plain. In this work the uplift history of the Bergell is studied in more detail by fission track dating of additional apatites from the Bergell region. Secondly, by determining apatite fission track ages the granitic boulders of the Po plain can be re-assigned to their original vertical position within the Bergell intrusive before erosion removed them in Late Oligocene time. A rather conservative estimate replaces them 6 km above the present morphology of the Bergell massif. Thus, the thickness of the Bergell granite must have been at least 8 km. Generally, fission track studies on boulders may become an important tool to study the vertical extent of mountain chains during the geological past. (Auth.)

  9. Restoration of a boulder reef in temperate waters: Strategy, methodology and lessons learnt

    DEFF Research Database (Denmark)

    Støttrup, Josianne Gatt; Dahl, Karsten; Niemann, Sanne

    2017-01-01

    Anthropogenic impacts on marine habitats are a global problem, particularly in coastal areas. While boulder reefs in temperate waters hold high biomass and biodiversity, and may be unable to recover from anthropogenic stressors without restoration efforts, little is known about how to restore and...

  10. Treatment of alumina refinery waste (red mud) through neutralization techniques: A review.

    Science.gov (United States)

    Rai, Suchita; Wasewar, K L; Agnihotri, A

    2017-06-01

    In the Bayer process of extraction of alumina from bauxite, the insoluble product generated after bauxite digestion with sodium hydroxide at elevated temperature and pressure is known as 'red mud' or 'bauxite residue'. This alumina refinery waste is highly alkaline in nature with a pH of 10.5-12.5 and is conventionally disposed of in mostly clay-lined land-based impoundments. The alkaline constituents in the red mud impose severe and alarming environmental problems, such as soil and air pollution. Keeping in view sustainable re-vegetation and residue management, neutralization/treatment of red mud using different techniques is the only alternative to make the bauxite residue environmentally benign. Hence, neutralization techniques, such as using mineral acids, acidic waste (pickling liquor waste), coal dust, superphosphate and gypsum as amenders, CO 2 , sintering with silicate material and seawater for treatment of red mud have been studied in detail. This paper is based upon and emphasizes the experimental work carried out for all the neutralization techniques along with a comprehensive review of each of the processes. The scope, applicability, limitations and feasibility of these processes have been compared exhaustively. Merits and demerits have been discussed using flow diagrams. All the techniques described are technically feasible, wherein findings obtained with seawater neutralization can be set as a benchmark for future work. Further studies should be focused on exploring the economical viability of these processes for better waste management and disposal of red mud.

  11. The effect of barite mud on the division of the detector energy window in density logging while drilling

    International Nuclear Information System (INIS)

    Zhang Li; Sun Jianmeng; Yu Huawei; Jiang Dong; Zhang Jing

    2012-01-01

    In the litho-density logging, formation density and lithology were acquired by calculating the total counts in certain energy window. Therefore, the division of the energy window directly affects the evaluation of density and lithology value. In the process of the energy window division, mud type affects the determination of the range of energy window. In this work, Monte Carlo simulation method was applied to study the range of energy window regarding to water mud and barite mud, respectively. The results show that the range of the energy window with barite mud is less than that of the water mud, and lithology identification will have greater' error in the barite mud. It is important to analyze influencing factors and improve the measurement accuracy of the litho-density logging. (authors)

  12. An active dealkalization of red mud with roasting and water leaching

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Xiaobo, E-mail: zhuxiaobo0119@126.com [School of Materials Science and Engineering, Henan Polytechnic University, Jiaozuo, Henan 454000 (China); Henan Key Discipline Open Laboratory of Mining Engineering Materials, Henan 454000 (China); Li, Wang; Guan, Xuemao [School of Materials Science and Engineering, Henan Polytechnic University, Jiaozuo, Henan 454000 (China); Henan Key Discipline Open Laboratory of Mining Engineering Materials, Henan 454000 (China)

    2015-04-09

    Highlights: • The dealkalization of active roasting and water leaching from red mud was put forward. • The main factors on dealkalization during active roasting and water leaching were investigated. • The mechanism of dealkalization from red mud was in-depth studied in the process. - Abstract: The research has focused on the dealkalization of red mud after active roasting and water leaching, which is obtained from bauxite during alumina production. The main factors such as roasting temperature, roasting time, water leaching stage, leaching temperature, leaching reaction time and liquid to solid ratio were investigated. The mechanism of dealkalization was in-depth studied by using ICP–AES, XRD, TG-DSC, SEM–EDS and leaching kinetic. The results show that the dealkalization rate reached 82% under the condition of roasting temperature of 700 °C, roasting time of 30 min, four stage water leaching, liquid to solid ratio of 7 mL/g, leaching temperature of 90 °C and reaction time of 60 min. The diffraction peak of Na{sub 6}CaAl{sub 6}Si{sub 6}(CO{sub 3})O{sub 24}·2H{sub 2}O in red mud was decreased during the active roasting process, whereas the mineral phases of NaOH·H{sub 2}O and Na{sub 2}Ca(CO{sub 3}){sub 2} were appeared. The content of alkali obviously decreased and the grade of other elements increased during the process of active roasting and water leaching, which was in favor of next application process of red mud. The water leaching was controlled by internal diffusion of SCM and the apparent activation energy was 22.63 kJ/mol.

  13. An active dealkalization of red mud with roasting and water leaching

    International Nuclear Information System (INIS)

    Zhu, Xiaobo; Li, Wang; Guan, Xuemao

    2015-01-01

    Highlights: • The dealkalization of active roasting and water leaching from red mud was put forward. • The main factors on dealkalization during active roasting and water leaching were investigated. • The mechanism of dealkalization from red mud was in-depth studied in the process. - Abstract: The research has focused on the dealkalization of red mud after active roasting and water leaching, which is obtained from bauxite during alumina production. The main factors such as roasting temperature, roasting time, water leaching stage, leaching temperature, leaching reaction time and liquid to solid ratio were investigated. The mechanism of dealkalization was in-depth studied by using ICP–AES, XRD, TG-DSC, SEM–EDS and leaching kinetic. The results show that the dealkalization rate reached 82% under the condition of roasting temperature of 700 °C, roasting time of 30 min, four stage water leaching, liquid to solid ratio of 7 mL/g, leaching temperature of 90 °C and reaction time of 60 min. The diffraction peak of Na 6 CaAl 6 Si 6 (CO 3 )O 24 ·2H 2 O in red mud was decreased during the active roasting process, whereas the mineral phases of NaOH·H 2 O and Na 2 Ca(CO 3 ) 2 were appeared. The content of alkali obviously decreased and the grade of other elements increased during the process of active roasting and water leaching, which was in favor of next application process of red mud. The water leaching was controlled by internal diffusion of SCM and the apparent activation energy was 22.63 kJ/mol

  14. Ash study for biogas purification

    International Nuclear Information System (INIS)

    Juarez V, R. I.

    2016-01-01

    This work evaluates the ashes generated from the wood and coal combustion process of the thermoelectric plant in Petacalco, Guerrero (Mexico) in order to determine its viability as a filter in the biogas purification process. The ash is constituted by particles of morphology and different chemical properties, so it required a characterization of the same by different analytical techniques: as was scanning electron microscopy and X-ray diffraction, in order to observe the microstructure and determine the elemental chemical composition of the particles. Prior to the analysis, a set of sieves was selected to classify as a function of particle size. Four different types of ashes were evaluated: one generated by the wood combustion (wood ash) and three more of the Petacalco thermoelectric generated by the coal combustion (wet fly ash, dry fly ash and dry bottom ash). (Author)

  15. Lunar ash flows - Isothermal approximation.

    Science.gov (United States)

    Pai, S. I.; Hsieh, T.; O'Keefe, J. A.

    1972-01-01

    Suggestion of the ash flow mechanism as one of the major processes required to account for some features of lunar soil. First the observational background and the gardening hypothesis are reviewed, and the shortcomings of the gardening hypothesis are shown. Then a general description of the lunar ash flow is given, and a simple mathematical model of the isothermal lunar ash flow is worked out with numerical examples to show the differences between the lunar and the terrestrial ash flow. The important parameters of the ash flow process are isolated and analyzed. It appears that the lunar surface layer in the maria is not a residual mantle rock (regolith) but a series of ash flows due, at least in part, to great meteorite impacts. The possibility of a volcanic contribution is not excluded. Some further analytic research on lunar ash flows is recommended.

  16. Regular Recycling of Wood Ash to Prevent Waste Production (RecAsh). Technical Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Lars E-mail: lars.t.andersson@skogsstyreslen.se

    2007-03-15

    At present, the extraction of harvest residues is predicted to increase in Sweden and Finland. As an effect of the intensified harvesting, the export of nutrients and acid buffering substances from the growth site is also increased. Wood ash could be used to compensate forest soils for such losses. Most wood fuel ash is today often deposited in landfills. If the wood ash is recycled, wood energy is produced without any significant waste production. Ash recycling would therefore contribute to decreasing the production of waste, and to maintaining the chemical quality of forest waters and biological productivity of forest soils in the long term. The project has developed, analysed and demonstrated two regular ash-recycling systems. It has also distributed knowledge gathered about motives for ash recycling as well as technical and administrative solutions through a range of media (handbooks, workshops, field demonstrations, reports, web page and information videos). Hopefully, the project will contribute to decreasing waste problems related to bio-energy production in the EU at large. The project has been organised as a separate structure at the beneficiary and divided in four geographically defined subprojects, one in Finland and three in Sweden (Central Sweden, Northern Sweden, and South-western Sweden). The work in each subproject has been lead by a subproject leader. Each subproject has organised a regional reference group. A project steering committee has been established consisting of senior officials from all concerned partners. The project had nine main tasks with the following main expected deliverables and output: 1. Development of two complete full-scale ash-recycling systems; 2. Production of handbooks of the ash recycling system; 3. Ash classification study to support national actions for recommendations; 4. Organise regional demonstrations of various technical options for ash treatment and spreading; 5. Organise national seminars and demonstrations of

  17. Electrodialytic removal of heavy metals from different fly ashes. Influence of heavy metal speciation in the ashes

    DEFF Research Database (Denmark)

    Pedersen, Anne Juul; Ottosen, Lisbeth M.; Villumsen, Arne

    2003-01-01

    Electrodialytic Remediation has recently been suggested as a potential method for removal of heavy metals from fly ashes. In this work electrodialytic remediation of three different fly ashes, i.e. two municipal solid waste incinerator (MSWI) fly ashes and one wood combustion fly ash was studied...... in lab scale, and the results were discussed in relation to the expected heavy metal speciation in the ashes. In initial leaching experiments the pH-dependent desorption characteristics of the heavy metals Cd, Pb, Zn and Cu were analogous in the two MSWI ashes, and thus it was expected......-moval efficiencies were observed, especially for Pb and Zn. Cd, the sole heavy metal of environmental concern in the wood ash, was found more tightly bonded in this ash than in the two MSWI ashes. It was suggested that complex Cd-silicates are likely phases in the wood ash whereas more soluble, condensed phases...

  18. Removal of fluoride ions from aqueous solution by waste mud

    Energy Technology Data Exchange (ETDEWEB)

    Kemer, Baris; Ozdes, Duygu; Gundogdu, Ali; Bulut, Volkan N.; Duran, Celal [Karadeniz Technical University, Faculty of Arts and Sciences, Department of Chemistry, 61080 Trabzon (Turkey); Soylak, Mustafa, E-mail: soylak@erciyes.edu.tr [Erciyes University, Faculty of Arts and Sciences, Department of Chemistry, 38039 Kayseri (Turkey)

    2009-09-15

    The present study was carried out to assess the ability of original waste mud (o-WM) and different types of activated waste mud which are acid-activated (a-WM) and precipitated waste mud (p-WM), in order to remove excess of fluoride from aqueous solution by using batch technique. The p-WM exhibited greater performance than the others. Adsorption studies were conducted as a function of pH, contact time, initial fluoride concentration, adsorbent concentration, temperature, etc. Studies were also performed to understand the effect of some co-existing ions present in aqueous solutions. Adsorption process was found to be almost independent of pH for all types of waste mud. Among the kinetic models tested for p-WM, pseudo-second-order model fitted the kinetic data well with a perfect correlation coefficient value of 1.00. It was found that the adequate time for the adsorption equilibrium of fluoride was only 1 h. Thermodynamic parameters including the Gibbs free energy ({Delta}G{sup o}), enthalpy ({Delta}H{sup o}), and entropy ({Delta}S{sup o}) revealed that adsorption of fluoride ions on the p-WM was feasible, spontaneous and endothermic in the temperature range of 0-40 deg. C. Experimental data showed a good fit with the Langmuir and Freundlich adsorption isotherm models. Results of this study demonstrated the effectiveness and feasibility of WM for removal of fluoride ions from aqueous solution.

  19. Development of alkali activated cements and concrete mixture design with high volumes of red mud

    OpenAIRE

    Krivenko, Pavel; Kovalchuk, Oleksandr; Pasko, Anton; Croymans, Tom; Hutt, Mikael; Lutter, Guillaume; Vandevenne, Niels; Schreurs, Sonja; Schroeyers, Wouter

    2017-01-01

    Dedicated cement compositions were formulated to enable the incorporation of large volume fractions of red mud in alkali activated cements, taking into account the role of the aluminosilicate phase in the processes of hydration and hardening. High volume red mud alkali activated cements were synthesized using a proper combination of red mud, low basic aluminosilicate compounds with a glass phase (blast-furnace slag) and additives selected from high-basic Ca-containing cements with a crystalli...

  20. Quantitative X-ray Diffraction (QXRD) analysis for revealing thermal transformations of red mud.

    Science.gov (United States)

    Liao, Chang-Zhong; Zeng, Lingmin; Shih, Kaimin

    2015-07-01

    Red mud is a worldwide environmental problem, and many authorities are trying to find an economic solution for its beneficial application or/and safe disposal. Ceramic production is one of the potential waste-to-resource strategies for using red mud as a raw material. Before implementing such a strategy, an unambiguous understanding of the reaction behavior of red mud under thermal conditions is essential. In this study, the phase compositions and transformation processes were revealed for the Pingguo red mud (PRM) heat-treated at different sintering temperatures. Hematite, perovskite, andradite, cancrinite, kaolinite, diaspore, gibbsite and calcite phases were observed in the samples. However, unlike those red mud samples from the other regions, no TiO2 (rutile or anatase) or quartz were observed. Titanium was found to exist mainly in perovskite and andradite while the iron mainly existed in hematite and andradite. A new silico-ferrite of calcium and aluminum (SFCA) phase was found in samples treated at temperatures above 1100°C, and two possible formation pathways for SFCA were suggested. This is the first SFCA phase to be reported in thermally treated red mud, and this finding may turn PRM waste into a material resource for the iron-making industry. Titanium was found to be enriched in the perovskite phase after 1200°C thermal treatment, and this observation indicated a potential strategy for the recovery of titanium from PRM. In addition to noting these various resource recovery opportunities, this is also the first study to quantitatively summarize the reaction details of PRM phase transformations at various temperatures. Copyright © 2015 Elsevier Ltd. All rights reserved.

  1. First international ash marketing and technology conference

    Energy Technology Data Exchange (ETDEWEB)

    1978-01-01

    A total of 42 papers were presented in sessions with the following headings: production and disposal of ash - an international review; environmental, health, safety, and legal aspects of ash handling; marketing of ash; development of new uses for ash; cementitious use of ash; ash in manufactured products; and geotechnical uses of ash.

  2. [Herpesvirus detection in clinically healthy West African mud turtles (Pelusioscastaneus)].

    Science.gov (United States)

    Marschang, R E; Heckers, K O; Heynol, V; Weider, K; Behncke, H

    2015-01-01

    First description of a herpesvirus in West African mud turtles. A herpesvirus was detected in two clinically healthy West African mud turtles (Pelusios castaneus) by PCR during a quarantine exam. The animals had been imported from Togo, West Africa to Germany for the pet trade. Analysis of a portion of the genome of the detected virus showed that it is a previously unknown virus related to other chelonid herpesviruses. The virus was named pelomedusid herpesvirus 1. This case highlights the importance of testing for infectious agents during quarantine, even in clinically healthy animals.

  3. Effects of drilling muds on lobster behavior. Progress report, 1 January-1 October 1979

    Energy Technology Data Exchange (ETDEWEB)

    Atema, J; Ashkenas, L; Beale, E

    1979-01-01

    Drilling muds, used and discarded in great quantities during the drilling phase of exploration and production of oil wells, represent an unknown threat to the marine environment. The compositions of the muds vary greatly with drilling requirements. The toxicity of their components are largely unknown, but can range from apparently harmless to immediately lethal, as found recently in toxicity tests on a number of marine animals. This report contains eight sections, each describing an aspect of studies of lobster behavior, ecology, physiology and the effects of exposure to various levels of different drilling muds.

  4. Evaluation of the hurricanes Gustav and Ike impact on mud from San Diego River using nuclear and geochemical techniques

    International Nuclear Information System (INIS)

    Diaz Rizo, O.; Gelen Rudnikas, A.; D'Alessandro Rodriguez, K.; Arado Lopez, J. O.; Dominguez Rodriguez, R.; Gonzalez Hernandez, P.; Melian Rodriguez, C.M.; Suarez Munnoz, M.; Fagundo Castillo, J. R.; Blanco Padilla, D.

    2011-01-01

    Effects induced by the hurricanes Gustav and Ike on San Diego River mud characteristics have been studied. X-ray fluorescence analysis, gamma spectrometry and measurement of some physic-chemical characteristics in mud samples, collected before and after hurricane impacts, shows that hurricanes induced changes in mud major composition and in some other mud characteristics, affecting its properties for therapeutic uses. The average sedimentation rate determined by gamma spectrometry in San Diego River outlet permit to estimate that the original mud characteristics will be recovered never before than 5-7 years. (Author)

  5. Cold seep communities in the deep eastern Mediterranean Sea: composition, symbiosis and spatial distribution on mud volcanoes

    NARCIS (Netherlands)

    Olu-Le Roy, K; Sibuet, M.; Fiala-Medioni, A.; Gofas, S; Salas, C.; Mariotti, A.; Foucher, J.-P.; Woodside, J.M.

    2004-01-01

    Two mud volcano fields were explored during the French-Dutch MEDINAUT cruise (1998) with the submersible NAUTILE, one south of Crete along the Mediteranean Ridge at about 2000 m depth (Olimpi mud field) and the other south of Turkey between 1700 and 2000 m depth (Anaximander mud field) where high

  6. A study of the properties of concrete, grout and paste containing red mud for use in repositories for nuclear waste

    International Nuclear Information System (INIS)

    Martensson, P.; Tang, L.; Ding, Z.; Peng, X.

    2015-01-01

    This paper presents the results from a study of the properties of concrete, grout and paste containing red mud - a waste product derived from the digestion of bauxite with a versatile mineralogical composition - for use in repositories for nuclear waste. Two types of red mud from China were used in the experiments. Type 1 was taken from Chiping Xinfa Hoayu Alumina Co. LTD, Liaocheng City, Shandong Province, China and type 2 taken from Xianfeng Alumina Co. LTD, Chongqing, China. In the experiments concrete, grout and paste in which 0, 10, 20 and 30 % of the mass of the binder was replaced by red mud were prepared for studies of the influence on the physical, mechanical and chemical properties of the materials. The results show that the compressive strength for concrete in which 30 % of the mass of the binder had been replaced by red mud was reduced from 47 to 29 MPa after curing for 28 days for red mud type 1 and from 46 to 39 MPa for red mud type 2 compared to specimens without red mud. This is attributed to that red mud type 2 contains a larger amount of CaO which can contribute in the hydration process of the cement as nucleation. The influence on dry shrinkage of concrete containing different proportions of red mud differed between the two types of red mud used in this study. A possible influence from the method used for curing the specimens prior to the measurements was also observed. Addition of red mud in grout significantly increased the water permeability. This was attributed to that increasing amounts of red mud increases the porosity of the specimens and that the red mud mainly acts as an inert filler in the grout. Adsorption tests on crushed hardened cement paste containing red mud showed fluctuating results but tests on the raw materials showed a high sorption capacity for Cs. (authors)

  7. Investigating Created Properties of Nanoparticles Based Drilling Mud

    Science.gov (United States)

    Ghasemi, Nahid; Mirzaee, Mojtaba; Aghayari, Reza; Maddah, Heydar

    2018-05-01

    The success of drilling operations is heavily dependent on the drilling fluid. Drilling fluids cool down and lubricate the drill bit, remove cuttings, prevent formation damage, suspend cuttings and also cake off the permeable formation, thus retarding the passage of fluid into the formation. Typical micro or macro sized loss circulation materials (LCM) show limited success, especially in formations dominated by micropores, due to their relatively large sizes. Due to unique characteristics of nanoparticles such as their size and high surface area to volume ratio, they play an effective role in solving problems associated with the drilling fluid. In this study, we investigate the effect of adding Al2O3 and TiO2 nanoparticles into the drilling mud. Al2O3 and TiO2 nanoparticles were used in 20 and 60 nm of size and 0.05 wt% in concentration. Investigating the effects of temperature and pressure has shown that an increase in temperature can reduce the drilling mud rheological properties such as plastic viscosity, while an increase in pressure can enhance these properties. Also, the effects of pressure in high temperatures were less than those in low temperatures. Studying the effects of adding nanoparticles has shown that they can reduce the drilling mud rheological properties. Moreover, they can increase gel strength, reduce capillary suction time and decrease formation damage.

  8. Determining ash content in flotation wastes by means of the MPOF optical ash meter. [Poland

    Energy Technology Data Exchange (ETDEWEB)

    Sikora, T; Sliwa, J

    1982-03-01

    The paper evaluates an experimental unit of the MPOF optical ash meter, developed by the EMAG Research and Production Center for Electrical Engineering and Mining Automation. The MPOF, which is being tested at the coal preparation plant of the 30 lecia PRL mine, is the first system for continuous determination of ash content in flotation tailings developed in Poland. A block scheme of the system is given. It consists of a measuring head and electronic system which processes data supplied by the measuring head and calculates ash content. System operation is based on the principle of determining ash content in a mixture of coal and mineral wastes by measuring mixture reflectivity. Determining ash content in the mixture is possible as reflectivity coefficients for coal and ash are constant. Performance of the MPOF optical ash meter is evaluated; the results are shown in a table and a scheme. Measurement accuracy is satisfactory.

  9. MODELING AND ANALYSIS OF UNSTEADY FLOW BEHAVIOR IN DEEPWATER CONTROLLED MUD-CAP DRILLING

    Directory of Open Access Journals (Sweden)

    Jiwei Li

    Full Text Available Abstract A new mathematical model was developed in this study to simulate the unsteady flow in controlled mud-cap drilling systems. The model can predict the time-dependent flow inside the drill string and annulus after a circulation break. This model consists of the continuity and momentum equations solved using the explicit Euler method. The model considers both Newtonian and non-Newtonian fluids flowing inside the drill string and annular space. The model predicts the transient flow velocity of mud, the equilibrium time, and the change in the bottom hole pressure (BHP during the unsteady flow. The model was verified using data from U-tube flow experiments reported in the literature. The result shows that the model is accurate, with a maximum average error of 3.56% for the velocity prediction. Together with the measured data, the computed transient flow behavior can be used to better detect well kick and a loss of circulation after the mud pump is shut down. The model sensitivity analysis show that the water depth, mud density and drill string size are the three major factors affecting the fluctuation of the BHP after a circulation break. These factors should be carefully examined in well design and drilling operations to minimize BHP fluctuation and well kick. This study provides the fundamentals for designing a safe system in controlled mud-cap drilling operati.

  10. Ash Properties of Alternative Biomass

    DEFF Research Database (Denmark)

    Capablo, Joaquin; Jensen, Peter Arendt; Pedersen, Kim Hougaard

    2009-01-01

    analysis into three main groups depending upon their ash content of silica, alkali metal, and calcium and magnesium. To further detail the biomass classification, the relative molar ratio of Cl, S, and P to alkali were included. The study has led to knowledge on biomass fuel ash composition influence...... on ash transformation, ash deposit flux, and deposit chlorine content when biomass fuels are applied for suspension combustion....

  11. The problem about the possibility of establishing an interrelation between the activity of the sun and that of mud volcanos

    Energy Technology Data Exchange (ETDEWEB)

    Mekhtiyev, Sh.F.; Khalilov, E.N.

    1984-01-01

    Studies of the mud volcanos of Eastern Azerbaydzhan showed that periods of weakening in the mud volcano activity correspond to periods of increased solar activity and the opposite. A graph which characterizes the change in the mud volcano activity in time is built to establish the association between solar activity and the activity of the mud volcanos. Data from 300 eruptions of mud volcanos of the world were used. All the world's mud volcanos are located in zones of high seismic activity. These zones are characterized by the presence of deeply focused (subcrust) earthquakes. All the mud volcanos are located along seismic strips of the earth, which reflect zones of subduction or the Zavaritskiy Benioff zones. The mud volcanos are associated with global geodynamic processes, while their activity characterizes the activity of the subduction zones. The activity of the subduction zones rises in periods of increased solar activity. Building a rectilinear trend of the Gauss capacity showed that the activation of the world's mud volcanos is increased in time at a speed of 0.02 eruptions per year. The activation of the subduction zones also rises in time. These studies are one of the first attempts to analyze data about the eruptions of the world's mud volcanos with consideration of the new global tectonics and certain cosmic processes.

  12. Biodiesel Production from Castor Oil by Using Calcium Oxide Derived from Mud Clam Shell

    Directory of Open Access Journals (Sweden)

    S. Ismail

    2016-01-01

    Full Text Available The catalytic potential of calcium oxide synthesized from mud clam shell as a heterogeneous catalyst for biodiesel production was studied. The mud clam shell calcium oxide was characterized using particle size analyzer, Fourier transform infrared spectroscopy, scanning electron microscopy, and BET gas sorption analyzer. The catalyst performance of mud clam shell calcium oxide was studied in the transesterification of castor oil as biodiesel. Catalyst characterization and transesterification study results of synthesized catalyst proved the efficiency of the natural derived catalyst for biodiesel production. A highest biodiesel yield of 96.7% was obtained at optimal parameters such as 1 : 14 oil-to-methanol molar ratio, 3% w/w catalyst concentration, 60°C reaction temperature, and 2-hour reaction time. Catalyst reusability test shows that the synthesized calcium oxide from mud clam shell is reusable up to 5 times.

  13. Detection of Buried Objects : The MUD Project

    NARCIS (Netherlands)

    Quesson, B.A.J.; Vossen, R. van; Zampolli, M.; Beckers, A.L.D.

    2011-01-01

    The aim of the Mine Underwater Detection (MUD) project at TNO is to experimentally investigate the acoustic and magnetic detection of explosives underwater, buried in a soft sediment layer. This problem is relevant for the protection of harbors and littoral assets against terrorist attacks and for

  14. Biotic and abiotic factors affect green ash volatile production and emerald ash borer adult feeding preference.

    Science.gov (United States)

    Chen, Yigen; Poland, Therese M

    2009-12-01

    The emerald ash borer, Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), is an exotic woodborer first detected in 2002 in Michigan and Ontario and is threatening the ash resource in North America. We examined the effects of light exposure and girdling on green ash (Fraxinus pennsylvanica Marsh) volatile production, and effects of light exposure, girdling, and leaf age on emerald ash borer adult feeding preferences and phototaxis. Green ash seedlings grown under higher light exposure had lower amounts of three individual volatile compounds, (Z)-3-hexenol, (E)-beta-ocimene, and (Z,E)-alpha-farnesene, as well as the total amount of six detected volatile compounds. Girdling did not affect the levels of these volatiles. Emerald ash borer females preferred mature leaves, leaves from girdled trees, and leaves grown in the sun over young leaves, leaves from nongirdled trees, and leaves grown in the shade, respectively. These emerald ash borer preferences were most likely because of physical, nutritional, or biochemical changes in leaves in response to the different treatments. Emerald ash borer females and males showed positive phototaxis in laboratory arenas, a response consistent with emerald ash borer preference for host trees growing in sunlight.

  15. 10 Risk to Ash from Emerald Ash Borer: Can Biological Control Prevent the Loss of Ash Stands

    Science.gov (United States)

    Ash trees were once relatively free of serious, major diseases and insect pests in North America until the arrival of EAB, which was first detected in North America in Michigan in 2002. As of February 2014, EAB had been detected in 22 U.S. states and two Canadian provinces, killing millions of ash ...

  16. Processed bottom ash for replacing fine aggregate in making high-volume fly ash concrete

    OpenAIRE

    Antoni; Sulistio Aldi Vincent; Wahjudi Samuel; Hardjito Djwantoro; Hardjito Djwantoro

    2017-01-01

    Bottom ash is a coal plant by-product that is abundant and underutilized. There is the potential use of bottom ash as a fine aggregate replacement in concrete mixtures; however, the problems of water absorption and uniformity of quality of the material need to be overcome first. In this study, bottom ash was treated by sieve separation and pounding to smaller particle size for use as a sand substitute. The physical and chemical characteristics of bottom ash were tested after treatment includi...

  17. Paleoclimate Reconstruction during the 17th to 18th Century Using Fossil Coral Tsunami Boulders from Ishigaki Island, the Ryukyus, Japan

    Science.gov (United States)

    Tsuzuki, K.; Yokoyama, Y.; Seki, A.; Kawakubo, Y.; Araoka, D.; Suzuki, A.

    2014-12-01

    Little Ice Age (LIA) which lasted during approximately 1450 to 1850 (e.g. Grove, 1988) is known as naturally occurring climate fluctuation, so knowing LIA in detail is necessary to improve climate models. Instrumental records can only extend back to about 100 years in many areas, thus paleoclimate records are reconstructed using proxies in tree rings, sediments and so force. However there are differences in reconstructed timings and magnitudes of LIA occurred in each area (Overpack et al., 1997), and most of the records are based mainly on terrestrial proxies such as tree ring records, whereas only limited numbers of marine records are available (Mann et al., 2008). Coral skeletal climatology is a useful tool to reconstruct marine paleoclimate records in tropics and subtropics. Hermatypic corals, Porites spp. have aragonite skeletons and they have annual bands, which are suitable to reconstruct high-resolution paleoclimate in seasonal scale by measuring chemical compositions. Skeletal Sr/Ca ratio in Porites spp. has been widely used as a reliable proxy of SST (Sea Surface Temperature). However, corals grow for approximately several decades to 200 years, hence it is difficult to reconstruct LIA paleoclimate using living corals. Cobb et al. (2003) used fossil corals casted on shore by storms to reconstruct millennial scale paleoclimate. There are fossil coral boulders in the eastern coast of Ishigaki Island, Ryukyus, Japan. These fossil coral boulders were casted on shore by paleo Tsunami events, thus they are called "Tsunami boulders" (Araoka et al., 2010). Fossil corals used by Cobb et al. have 30-90-year records while some large Tsunami boulders have multi-centennial continuous records. In this study, we reconstruct paleo SST using the Tsunami boulder from Ishigaki Island. The boulder has 185 years of annual banding. U-series dating shows the boulder was moved on shore at Meiwa earthquake in 1771. We measure Sr/Ca ratio using LA-HR-ICPMS (Laser Ablation High

  18. Effect of Lubrication on Sliding Wear of Red Mud Particulate Reinforced Aluminium Alloy 6061

    Directory of Open Access Journals (Sweden)

    N. Panwar

    2017-09-01

    Full Text Available In present study, Red mud, an industrial waste, has been utilized as a reinforcement material to fabricate Aluminium 6061 matrix based metal matrix composite. Taguchi L18 orthogonal array has been employed for fabrication of composite castings and for conducting the tribological experimentation. ANOVA analysis has been applied to examine the effect of individual parameters such as sliding condition: dry and wet, reinforcement weight fraction, load, speed, and sliding distance on specific wear rate obtained experimentally. It has been found that tensile strength and impact energy increases while elongation decreases, with increasing weight fraction and decrease in particle size of red mud. The percentage contribution of the effect of factors on SWR is Sliding condition (73.17, speed (7.84, percentage reinforcement (7.35, load (5.75, sliding distance (2.24, and particle size (1.25. It has also been observed that specific wear rate is very low in wet condition. However, it decreases with increase in weight fraction of reinforcement, decrease in load and sliding speed. Al6061/red mud metal matrix composites have shown reasonable strength and wear resistance. The use of red mud in Aluminium composite provides the solution for disposal of red mud and can possibly become an economic replacement of Aluminium and its alloys.

  19. Influence of calcined mud on the mechanical properties and shrinkage of self-compacting concrete

    Directory of Open Access Journals (Sweden)

    Fatima Taieb

    2018-01-01

    Full Text Available The use of SCC has a particular interest in terms of sustainable development. Indeed, their specific formulation leads to a greater volume of dough than for common concretes, thus, a larger quantity of cement. However, for economical, ecological and technical reasons, it is sought to limit their cement content [1]. It is therefore necessary to almost always use mineral additions as a partial replacement for cement because the technology of self-compacting concretes can consume large quantities of fines, in this case calcinated mud issued from dams dredging sediments that can give and/or ameliorate characteristics and performances of this type of concretes. Four SCCs had been formulated from the same composition where the only percentage of calcinated mud of Chorfa (west of Algeria dam changed (0%, 10%, 20% and 30%. The effect of calcinated mud on characteristics at fresh state of SCC according to AFGC was quantified. Mechanical strengths and shrinkage deformation (total, autogenous, drying were evaluated. The results show the possibility to make SCCs with different dosages of calcinated mud having strengths that can defy those of the control SCC. The analysis of free deformations indicates the beneficial impact of the mud by contributing to decrease the amplitudes of the shrinkage compared to those of the control SCC.

  20. Use of Oil-Based Mud Cutting Waste in Cement Clinker Manufacturing

    OpenAIRE

    Saif Al-Dhamri, H; Black, L

    2014-01-01

    Oil-based Mud (OBM) cutting waste is generated during the process of oil well drilling. The drilled rocks are removed from deep within the drilled well and pumped to the surface. The portion removed , known at "cutting", is a mixture of rocks, mud, water and oil. Most drilling companies store this waste in open yards with no specific treatment solution. The environmental regulations in Oman specify that storage should involve isolation, to prevent penetration of the contamination to the surfa...

  1. Characterization of metals released from coal fly ash during dredging at the Kingston ash recovery project.

    Science.gov (United States)

    Bednar, A J; Averett, D E; Seiter, J M; Lafferty, B; Jones, W T; Hayes, C A; Chappell, M A; Clarke, J U; Steevens, J A

    2013-09-01

    A storage-pond dike failure occurred on December 22, 2008 at the Tennessee Valley Authority Kingston Fossil Plant resulting in the release of over 4million cubic meters (5million cubic yards) of fly ash. Approximately half of the released ash was deposited in the main channel of the Emory River, Tennessee, USA. Remediation efforts of the Emory River focused on hydraulic dredging, as well as mechanical excavation in targeted areas. However, agitation of the submerged fly ash during hydraulic dredging introduces river water into the fly ash material, which could promote dissolution and desorption of metals from the solid fly ash material. Furthermore, aeration of the dredge slurry could alter the redox state of metals in the fly ash material and thereby change their sorption, mobility, and toxicity properties. The research presented here focuses on the concentrations and speciation of metals during the fly ash recovery from the Emory River. Our results indicate that arsenite [As(III)] released from the fly ash material during dredging was slowly oxidized to arsenate [As(V)] in the slurry recovery system with subsequent removal through precipitation or sorption reactions with suspended fly ash material. Concentrations of other dissolved metals, including iron and manganese, also generally decreased in the ash recovery system prior to water discharge back to the river. Published by Elsevier Ltd.

  2. Prospects for ash pond reclamation

    Energy Technology Data Exchange (ETDEWEB)

    Shyyam, A.K.; Shukla, K.S.; Agrawal, D. (National Thermal Power Corporation Ltd., New Delhi (India))

    1993-01-01

    A typical modern coal fired station in India burns 0.7 t/MWh of coal and consequently generates ash at 0.245 t/MWh. The physical nature of ash, low available concentrations of certain plant nutrients and the presence of phytotoxic trace elements render fly ash marginally adequate for plant growth. As fly ash itself was thought to be an inappropriate growth medium for plants, regulators decided that a soil cover is mandatory. There is ample data to suggest that the attributes of fly ash detrimental to plant growth can be ameliorated, allowing the establishment of vegetation directly on fly ash surfaces. The natural revegetation of fly ash disposal sites has been reported in the world. The natural vegetation pioneered by Cynodon at different stages of ecological succession and comprising of species such as [ital Calotropis gigantea], [ital Lippia nodiflora], [ital Ipomea, cornea], [ital Xanthium parviflorum] has been noted at one of the NTPC projects, in Badarpur Thermal Power Station. Since natural reclamation is a time-consuming process, experimental trials of growing some species over the temporary ash lagoon directly (without soil cover) were carried out at Ramagundam Super Thermal Power Project (RSTPP) of NTPC, in South India to achieve faster results than the natural process. 6 refs., 8 figs.

  3. Radioisotope conveyor ash meter

    International Nuclear Information System (INIS)

    Savelov, V.D.

    1994-01-01

    Radioisotope conveyor ash meter realizes persistent measuring of ashiness of coal and products of its enrichment on the belt conveyor without contact. The principle of ash meter acting is based on functional dependence of the gamma radiation flows backscattering intensity of radioisotope sources from the ash volume content in the controlled fuel. Facility consists from the ashiness transducer and the processing and control device

  4. Environmental control of drilling mud discharge through dewatering in cold weather climates: effect of ambient temperature

    Energy Technology Data Exchange (ETDEWEB)

    Wojtanowicz, A. K. [Louisiana State Univ., Baton Rouge, LA (United States); Ye, Y. [Jianghan Petroleum Institute, Beijing, (China)

    1998-05-01

    Results of an experimental study of the effects of drilling mud temperature upon dewatering performance at various temperatures were presented. Three temperature ranges (from flowline temperature to room temperature, from room temperature to freezing point, and freeze/thaw, i.e. from -20 degrees C to 12 degrees C) were considered. Both unweighted and weighted fresh water muds and weighted salt water mud were tested using a sealed laboratory batch reactor, to prevent rapid vaporization of separated water at temperatures above 60 degrees C. Deep freezing was achieved by using ice or ice-salt baths. Net water removal was measured with a bench-top plate press under constant expression pressure of 270 kPa. Results showed that the freeze/thaw treatment process proved to be very effective, enhancing water removal by 34 to 39 per cent, and reducing waste mud volume by 64 to 72 per cent. No advantage to dewatering hot drilling mud from active systems was observed at temperatures above 21 degrees C. It was suggested that at temperatures under 21 degrees C, the waste drilling mud diverted from an active system should be dewatered when its temperature is still over 40 degrees C. to reduce the amount of chemicals needed for separation enhancement. 14 refs., 4 tabs., 4 figs.

  5. Capping hazardous red mud using acidic soil with an embedded layer of zeolite for plant growth.

    Science.gov (United States)

    Ma, Yingqun; Si, Chunhua; Lin, Chuxia

    2014-01-01

    A nearly three-year microcosm experiment was conducted to test the effectiveness of capping red mud using acidic soil with an embedded layer of zeolite in sustaining the growth of a grass species. This 'sandwich-structured' design allowed self-sustaining growth of the plants under rain-fed conditions no matter whether the underlying red mud was neutralized or not. During the initial stage, the plants grew better when the red mud was not neutralized with MgCl2 probably due to pH rise in the root zone. Neutralization of red mud led to salinization and pH decrease in the root zone. However, the difference in plant growth performance between these scenarios became less remarkable over time due to gradual improvement of soil conditions in the neutralized scenarios. Continuous leaching of soluble salts and alkali by rainwater extended the root zone to the red mud layer. As a result of vegetative production, soil organic matter rapidly accumulated. This, combined with increase in pH and decrease in salinity, markedly facilitated microbial activities and consequently improved the supply of nutrients. This study provides abasis for field-scale experimental design that will have implications for effectively establishing vegetative cover in red mud disposal sites to control dust hazards.

  6. Bioleaching of trace metals from coal ash using local isolate from coal ash ponds

    Directory of Open Access Journals (Sweden)

    Pangayao Denvert

    2018-01-01

    Full Text Available Bioleaching of chromium, copper, manganese and zinc from coal ash were investigated using isolates from coal ash ponds particularly Psuedomonas spp. Six (6 different coal ash ponds were examined however, after initial screening Psuedomonas spp. were only present in three (3 coal ash ponds. Among the three coal ash ponds, results showed that eight (8 putative Pseudomonas spp. isolates were present that were identified using the Polymerase Chain Reaction (PCR. Using the eight putative Pseudomonas spp. for bioleaching at optimum conditions and 15 days, the pH value ranges from 8.26 to 8.84 which was basic in nature. Moreover, the maximum metal leached were 8.04% Cr, 12.05% Cu, 4.34% Mn and 10.63% Zn.

  7. Differential InSAR Monitoring of the Lampur Sidoarjo Mud Volcano (Java, Indonesia) Using ALOS PALSAR Imagery

    Science.gov (United States)

    Thomas, Adam; Holley, Rachel; Burren, Richard; Meikle, Chris; Shilston, David

    2010-03-01

    The Lampur Sidoarjo mud volcano (Java, Indonesia), colloquially called LUSI, first appeared in May 2006. Its cause, whether the result of natural or anthropogenic activities (or a combination of both), is still being debated within the academic, engineering and political communities.The mud volcano expels up to 150,000 m3 of mud per day; and over time, this large volume of mud has had a major environmental and economic impact on the region. The mud flow from LUSI has now covered 6 km2 to depths some tens of metres, displacing approximately 30,000 residents; and continues to threaten local communities, businesses and industry. With such a large volume of mud being expelled each day it is inevitable (as with onshore oil and gas production fields) that there will be some ground surface movement and instability issues at the mud source (the main vent), and in the vicinity of the mud volcano footprint.Due to the dynamic ground surface conditions, engineers and academics alike have found it difficult to reliably monitor ground surface movements within the effected region using conventional surveying techniques. Consequently, engineers responsible for the risk assessment of ground surface instabilities within the proximity of LUSI have called upon the use of satellite interferometry to continually monitor the hazard.The Advanced Land Observing Satellite (ALOS), launched on 24th January 2006, carries onboard an L- band Synthetic Aperture Radar (SAR) instrument called PALSAR (Phased Array type L-band Synthetic Aperture Radar). In contrast to established C-band (5.6cm wavelength) SAR instruments onboard ERS-1 & -2, Envisat, Radarsat-1, and the recently launched Radarsat-2 satellite, PALSAR's (L-band/23.8cm wavelength) instrument presents a number of advantages, including the ability to map larger-scale ground motions, over relatively short timeframes, in tropical environments, without suffering as significantly from signal decorrelation associated with C-band imagery

  8. Natural radioactivity in Egyptian and industrially used australian bauxites and its tailing red mud

    International Nuclear Information System (INIS)

    Ibrahirm, N.; Abd el Maksoud, T.; El Ezaby, B.; Nada, A.; Abu Zeid, H.

    1999-01-01

    Red mud is produced in considerable masses as a waste product in the production of aluminum from bauxite. It may be used for industrial or agricultural purposes. According to it's genesis by weathering and sedimentation bauxites contain high concentrations of uranium and thorium. Three Egyptian bauxites, Australian industry used bauxite and its red mud tailing were analyzed by a high resolution gamma spectrometer, with a hyper pure germanium detector. The three Egyptian bauxites show high concentrations in uranium series, and around 120 Bq kg -1 for uranium -235. K-40 concentrations for these samples ranged from 289 to 575 Bq kg -1 . Thorium series concentrations show lower values. The industrially used bauxite shows very low concentrations for all radioactive nuclides. Its tailing red mud as a low level radioactive waste LLRW, shows low concentrations for uranium - series, thorium - series and also 40 K, so it is recommended to be used in industrial and agricultural purposes, which is not permissible for the normal red mud. (author)

  9. Clinical and anti-aging effect of mud-bathing therapy for patients with fibromyalgia.

    Science.gov (United States)

    Maeda, Toyoki; Kudo, Yoshihiro; Horiuchi, Takahiko; Makino, Naoki

    2017-12-06

    Spa bathing is known as a medical treatment for certain diseases causing chronic pains. Spa water contains mineral components which lower the specific heat of the water, resulting in a higher efficiency to warm body-core temperature. This phenomenon yields pain-relieving effect for rheumatoid arthritis, low back pain, sciatic neuralgia, fibromyalgia, etc. Here we introduce medical and biological effects of mud-spa-bathing therapy for fibromyalgia other than pain relief, the changes of blood examination data, and the telomere length of circulating leukocytes. The enrolled 7 patients with fibromyalgia syndrome were hospitalized and were subject to daily mud bathing at 40 °C for 10 min for about a month. Then, their subjective pain was reduced to about a quarter in average. They also showed lowered serum triglyceride and C-reactive protein level, maintaining the levels of aspartate transaminase and creatine phosphokinase, and increases of the red blood cell count, the serum albumin level, and the serum LDL-cholesterol level in comparison with cases without mud-bathing therapy, suggesting that mud bathing prevents inflammation and muscle atrophy and improves nutritional condition in fibromyalgia. In addition, the analysis of telomere length of peripheral leukocytes revealed a trend of negative correlation between telomere shortening and laboratory data change of hemoglobin and serum albumin. These telomeric changes can be explained hypothetically by an effect of mud bathing extending life-span of circulating leukocytes.

  10. Optimizing and Characterizing Geopolymers from Ternary Blend of Philippine Coal Fly Ash, Coal Bottom Ash and Rice Hull Ash

    Directory of Open Access Journals (Sweden)

    Martin Ernesto Kalaw

    2016-07-01

    Full Text Available Geopolymers are inorganic polymers formed from the alkaline activation of amorphous alumino-silicate materials resulting in a three-dimensional polymeric network. As a class of materials, it is seen to have the potential of replacing ordinary Portland cement (OPC, which for more than a hundred years has been the binder of choice for structural and building applications. Geopolymers have emerged as a sustainable option vis-à-vis OPC for three reasons: (1 their technical properties are comparable if not better; (2 they can be produced from industrial wastes; and (3 within reasonable constraints, their production requires less energy and emits significantly less CO2. In the Philippines, the use of coal ash, as the alumina- and silica- rich geopolymer precursor, is being considered as one of the options for sustainable management of coal ash generation from coal-fired power plants. However, most geopolymer mixes (and the prevalent blended OPC use only coal fly ash. The coal bottom ash, having very few applications, remains relegated to dumpsites. Rice hull ash, from biomass-fired plants, is another silica-rich geopolymer precursor material from another significantly produced waste in the country with only minimal utilization. In this study, geopolymer samples were formed from the mixture of coal ash, using both coal fly ash (CFA and coal bottom ash (CBA, and rice hull ash (RHA. The raw materials used for the geopolymerization process were characterized using X-ray fluorescence spectroscopy (XRF for elemental and X-ray diffraction (XRD for mineralogical composition. The raw materials’ thermal stability and loss on ignition (LOI were determined using thermogravimetric analysis (TGA and reactivity via dissolution tests and inductively-coupled plasma mass spectrometry (ICP analysis. The mechanical, thermal and microstructural properties of the geopolymers formed were analyzed using compression tests, Fourier transform infra-red spectroscopy (FTIR

  11. Optimizing and Characterizing Geopolymers from Ternary Blend of Philippine Coal Fly Ash, Coal Bottom Ash and Rice Hull Ash.

    Science.gov (United States)

    Kalaw, Martin Ernesto; Culaba, Alvin; Hinode, Hirofumi; Kurniawan, Winarto; Gallardo, Susan; Promentilla, Michael Angelo

    2016-07-15

    Geopolymers are inorganic polymers formed from the alkaline activation of amorphous alumino-silicate materials resulting in a three-dimensional polymeric network. As a class of materials, it is seen to have the potential of replacing ordinary Portland cement (OPC), which for more than a hundred years has been the binder of choice for structural and building applications. Geopolymers have emerged as a sustainable option vis-à-vis OPC for three reasons: (1) their technical properties are comparable if not better; (2) they can be produced from industrial wastes; and (3) within reasonable constraints, their production requires less energy and emits significantly less CO₂. In the Philippines, the use of coal ash, as the alumina- and silica- rich geopolymer precursor, is being considered as one of the options for sustainable management of coal ash generation from coal-fired power plants. However, most geopolymer mixes (and the prevalent blended OPC) use only coal fly ash. The coal bottom ash, having very few applications, remains relegated to dumpsites. Rice hull ash, from biomass-fired plants, is another silica-rich geopolymer precursor material from another significantly produced waste in the country with only minimal utilization. In this study, geopolymer samples were formed from the mixture of coal ash, using both coal fly ash (CFA) and coal bottom ash (CBA), and rice hull ash (RHA). The raw materials used for the geopolymerization process were characterized using X-ray fluorescence spectroscopy (XRF) for elemental and X-ray diffraction (XRD) for mineralogical composition. The raw materials' thermal stability and loss on ignition (LOI) were determined using thermogravimetric analysis (TGA) and reactivity via dissolution tests and inductively-coupled plasma mass spectrometry (ICP) analysis. The mechanical, thermal and microstructural properties of the geopolymers formed were analyzed using compression tests, Fourier transform infra-red spectroscopy (FTIR), scanning

  12. Effects of the addition of oil shale ash and coal ash on physic-chemical properties of CPJ45 cement

    Directory of Open Access Journals (Sweden)

    Nabih K.

    2014-04-01

    Full Text Available We focused our research on recycling industrial wastes, fly ash (F.A, bottom ash (B.A and oil shale ash (S.A in cement production. The study concerns physico-chemical characterization of these products and the influence of their addition on the mechanical proprieties of the CPJ45 cement. XRF allowed us to rank the three additives used according to their contents on major oxides. Coal ashes belong to the class F, and thus possess poozzolanic properties and oil shale ash belongs to the class C and possesses hydraulic and poozolanic properties. The crystalline phases constituting each ash were analysed by XRD. We observe in bottom ash the presence of quartz and mullite. The same crystals are found in fly ash with hematite and magnetite. Oil shale ash is composed of quartz, anhydrite, gehlenite, wollastonite and periclase. The microstructures of fly ash and bottom ash were studied using SEM. The bottom ash was composed respectively of fine particles that are generally irregularly shaped, their dimensions are between 5 and 28μm and of big particles(300 μm. The EDX analysis coupled with an electronic microscope provided some information about the major elements that constitute our samples. The dehydrations of anhydrous and three days hydrated cement were examined by DSC. For hydrated cements we noticed endothermic peaks related to the dehydration of CSH, CH and decomposition of carbonates. The study of the mechanical properties of CPJ45 cement by adding different proportions of fly ash, bottom ash and oil shale ash helped clarifying the percentage of ash that leaded to improve the 28 days mechanical strength. The results show that the cements studied have their maximum mechanical resistance with the addition at 7% of fly ash or 10% of oil shale ash.

  13. Fly ash dynamics in soil-water systems

    International Nuclear Information System (INIS)

    Sharma, S.; Fulekar, M.H.; Jayalakshmi, C.P.

    1989-01-01

    Studies regarding the effluents and coal ashes (or fly ash) resulting from coal burning are numerous, but their disposal and interactions with the soil and water systems and their detailed environmental impact assessment with concrete status reports on a global scale are scanty. Fly ash dynamics in soil and water systems are reviewed. After detailing the physical composition of fly ash, physicochemical changes in soil properties due to fly ash amendment are summarized. Areas covered include texture and bulk density, moisture retention, change in chemical equilibria, and effects of fly ash on soil microorganisms. Plant growth in amended soils is discussed, as well as plant uptake and accumulation of trace elements. In order to analyze the effect of fly ash on the physicochemical properties of water, several factors must be considered, including surface morphology of fly ash, pH of the ash sluice water, pH adjustments, leachability and solubility, and suspended ash and settling. The dynamics of fly ash in water systems is important due to pollution of groundwater resources from toxic components such as trace metals. Other factors summarized are bioaccumulation and biomagnification, human health effects of contaminants, and the impact of radionuclides in fly ash. Future research needs should focus on reduction of the environmental impact of fly ash and increasing utilization of fly ash as a soil amendment. 110 refs., 2 figs., 10 tabs

  14. Geochemical evolution of groundwater in the Mud Lake area, eastern Idaho, USA

    Science.gov (United States)

    Rattray, Gordon W.

    2015-01-01

    Groundwater with elevated dissolved-solids concentrations—containing large concentrations of chloride, sodium, sulfate, and calcium—is present in the Mud Lake area of Eastern Idaho. The source of these solutes is unknown; however, an understanding of the geochemical sources and processes controlling their presence in groundwater in the Mud Lake area is needed to better understand the geochemical sources and processes controlling the water quality of groundwater at the Idaho National Laboratory. The geochemical sources and processes controlling the water quality of groundwater in the Mud Lake area were determined by investigating the geology, hydrology, land use, and groundwater geochemistry in the Mud Lake area, proposing sources for solutes, and testing the proposed sources through geochemical modeling with PHREEQC. Modeling indicated that sources of water to the eastern Snake River Plain aquifer were groundwater from the Beaverhead Mountains and the Camas Creek drainage basin; surface water from Medicine Lodge and Camas Creeks, Mud Lake, and irrigation water; and upward flow of geothermal water from beneath the aquifer. Mixing of groundwater with surface water or other groundwater occurred throughout the aquifer. Carbonate reactions, silicate weathering, and dissolution of evaporite minerals and fertilizer explain most of the changes in chemistry in the aquifer. Redox reactions, cation exchange, and evaporation were locally important. The source of large concentrations of chloride, sodium, sulfate, and calcium was evaporite deposits in the unsaturated zone associated with Pleistocene Lake Terreton. Large amounts of chloride, sodium, sulfate, and calcium are added to groundwater from irrigation water infiltrating through lake bed sediments containing evaporite deposits and the resultant dissolution of gypsum, halite, sylvite, and bischofite.

  15. Rare earth elements behavior in Peruibe black mud

    International Nuclear Information System (INIS)

    Torrecilha, Jefferson K.; Carvalho, Leandro P.; Gouvea, Paulo F.M.; Silva, Paulo S.C. da

    2015-01-01

    Rare earth elements in sediments have been used as powerful tools for environmental studies because of their behavior during geochemical processes and are also widely accepted as reliable provenance tracers because they are largely water-immobile and thus behave conservatively during sedimentary processes. The Peruibe Black Mud (PBM) is a sedimentary deposit originated from the interactions of marine sediments and organic matter in an estuarine environment that originates a peloid currently used for medicinal purposes. The objective of this study was to examine rare earth elements pattern distribution in the Peruibe black mud sedimentary deposit as a proxy for its geochemical development. Elemental ratios such as LaN/YbN, Th/U and La/Th were determined and a normalization of the mean rare earth elements concentrations in the samples related to NASC indicates that the light (La to Eu) rare earth elements present values close to the unity while the heavy (Tb to Lu) rare earth elements are depleted related to NASC. It can be observed that the light rare earth elements present enrichment values slightly enriched over the unity while the heavy rare earth elements present values generally below the unity reflecting the enrichment of the light rare earth elements over the heavy rare earth. Rare earth elements concentrations determined in Peruibe black mud samples showed a distribution similar to that found in the NASC for the light rare earth elements and depleted for the heavy rare earth elements. (author)

  16. Rare earth elements behavior in Peruibe black mud

    Energy Technology Data Exchange (ETDEWEB)

    Torrecilha, Jefferson K.; Carvalho, Leandro P.; Gouvea, Paulo F.M.; Silva, Paulo S.C. da, E-mail: jeffkoy@usp.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2015-07-01

    Rare earth elements in sediments have been used as powerful tools for environmental studies because of their behavior during geochemical processes and are also widely accepted as reliable provenance tracers because they are largely water-immobile and thus behave conservatively during sedimentary processes. The Peruibe Black Mud (PBM) is a sedimentary deposit originated from the interactions of marine sediments and organic matter in an estuarine environment that originates a peloid currently used for medicinal purposes. The objective of this study was to examine rare earth elements pattern distribution in the Peruibe black mud sedimentary deposit as a proxy for its geochemical development. Elemental ratios such as LaN/YbN, Th/U and La/Th were determined and a normalization of the mean rare earth elements concentrations in the samples related to NASC indicates that the light (La to Eu) rare earth elements present values close to the unity while the heavy (Tb to Lu) rare earth elements are depleted related to NASC. It can be observed that the light rare earth elements present enrichment values slightly enriched over the unity while the heavy rare earth elements present values generally below the unity reflecting the enrichment of the light rare earth elements over the heavy rare earth. Rare earth elements concentrations determined in Peruibe black mud samples showed a distribution similar to that found in the NASC for the light rare earth elements and depleted for the heavy rare earth elements. (author)

  17. Fly ash quality and utilization

    Energy Technology Data Exchange (ETDEWEB)

    Barta, L.E.; Lachner, L.; Wenzel, G.B. [Inst. for Energy, Budapest (Hungary); Beer, M.J. [Massachusetts Inst. of Technology, Cambridge, MA (United States)

    1995-12-01

    The quality of fly ash is of considerable importance to fly ash utilizers. The fly ash puzzolanic activity is one of the most important properties that determines the role of fly ash as a binding agent in the cementing process. The puzzolanic activity, however is a function of fly ash particle size and chemical composition. These parameters are closely related to the process of fly ash formation in pulverized coal fired furnaces. In turn, it is essential to understand the transformation of mineral matter during coal combustion. Due to the particle-to-particle variation of coal properties and the random coalescence of mineral particles, the properties of fly ash particles e.g. size, SiO{sub 2} content, viscosity can change considerably from particle to particle. These variations can be described by the use of the probability theory. Since the mean values of these randomly changing parameters are not sufficient to describe the behavior of individual fly ash particles during the formation of concrete, therefore it is necessary to investigate the distribution of these variables. Examples of these variations were examined by the Computer Controlled Scanning Electron Microscopy (CCSEM) for particle size and chemical composition for Texas lignite and Eagel Butte mineral matter and fly ash. The effect of combustion on the variations of these properties for both the fly ash and mineral matter were studied by using a laminar flow reactor. It is shown in our paper, that there are significant variations (about 40-50% around the mean values) of the above-listed properties for both coal samples. By comparing the particle size and chemical composition distributions of the mineral matter and fly ash, it was possible to conclude that for the Texas lignite mineral matter, the combustion did not effect significantly the distribution of these properties, however, for the Eagel Butte coal the combustion had a major impact on these mineral matter parameters.

  18. Ash cloud aviation advisories

    Energy Technology Data Exchange (ETDEWEB)

    Sullivan, T.J.; Ellis, J.S. [Lawrence Livermore National Lab., CA (United States); Schalk, W.W.; Nasstrom, J.S. [EG and G, Inc., Pleasanton, CA (United States)

    1992-06-25

    During the recent (12--22 June 1991) Mount Pinatubo volcano eruptions, the US Air Force Global Weather Central (AFGWC) requested assistance of the US Department of Energy`s Atmospheric Release Advisory Capability (ARAC) in creating volcanic ash cloud aviation advisories for the region of the Philippine Islands. Through application of its three-dimensional material transport and diffusion models using AFGWC meteorological analysis and forecast wind fields ARAC developed extensive analysis and 12-hourly forecast ash cloud position advisories extending to 48 hours for a period of five days. The advisories consisted of ``relative`` ash cloud concentrations in ten layers (surface-5,000 feet, 5,000--10,000 feet and every 10,000 feet to 90,000 feet). The ash was represented as a log-normal size distribution of 10--200 {mu}m diameter solid particles. Size-dependent ``ashfall`` was simulated over time as the eruption clouds dispersed. Except for an internal experimental attempt to model one of the Mount Redoubt, Alaska, eruptions (12/89), ARAC had no prior experience in modeling volcanic eruption ash hazards. For the cataclysmic eruption of 15--16 June, the complex three-dimensional atmospheric structure of the region produced dramatically divergent ash cloud patterns. The large eruptions (> 7--10 km) produced ash plume clouds with strong westward transport over the South China Sea, Southeast Asia, India and beyond. The low-level eruptions (< 7 km) and quasi-steady-state venting produced a plume which generally dispersed to the north and east throughout the support period. Modeling the sequence of eruptions presented a unique challenge. Although the initial approach proved viable, further refinement is necessary and possible. A distinct need exists to quantify eruptions consistently such that ``relative`` ash concentrations relate to specific aviation hazard categories.

  19. Identifying glass compositions in fly ash

    Directory of Open Access Journals (Sweden)

    Katherine eAughenbaugh

    2016-01-01

    Full Text Available In this study, four Class F fly ashes were studied with a scanning electron microscope; the glassy phases were identified and their compositions quantified using point compositional analysis with k-means clustering and multispectral image analysis. The results showed that while the bulk oxide contents of the fly ashes were different, the four fly ashes had somewhat similar glassy phase compositions. Aluminosilicate glasses (AS, calcium aluminosilicate glasses (CAS, a mixed glass, and, in one case, a high iron glass were identified in the fly ashes. Quartz and iron crystalline phases were identified in each fly ash as well. The compositions of the three main glasses identified, AS, CAS, and mixed glass, were relatively similar in each ash. The amounts of each glass were varied by fly ash, with the highest calcium fly ash containing the most of calcium-containing glass. Some of the glasses were identified as intermixed in individual particles, particularly the calcium-containing glasses. Finally, the smallest particles in the fly ashes, with the most surface area available to react in alkaline solution, such as when mixed with portland cement or in alkali-activated fly ash, were not different in composition than the large particles, with each of the glasses represented. The method used in the study may be applied to a fly ash of interest for use as a cementing material in order to understand its potential for reactivity.

  20. The Role of Biocontrol of Emerald Ash Borer in Protecting Ash Regeneration after Invasion

    Science.gov (United States)

    Emerald ash borer (EAB) is an invasive Asian beetle that is destroying ash in forests over much of eastern North America because of the high susceptibility of our native ash and a lack of effective natural enemies. To increase mortality of EAB larvae and eggs, the USDA (FS, ARS and APHIS) is carryin...

  1. Novel Desorber for Online Drilling Mud Gas Logging.

    Science.gov (United States)

    Lackowski, Marcin; Tobiszewski, Marek; Namieśnik, Jacek

    2016-01-01

    This work presents the construction solution and experimental results of a novel desorber for online drilling mud gas logging. The traditional desorbers use mechanical mixing of the liquid to stimulate transfer of hydrocarbons to the gaseous phase that is further analyzed. The presented approach is based on transfer of hydrocarbons from the liquid to the gas bubbles flowing through it and further gas analysis. The desorber was checked for gas logging from four different drilling muds collected from Polish boreholes. The results of optimization studies are also presented in this study. The comparison of the novel desorber with a commercial one reveals strong advantages of the novel one. It is characterized by much better hydrocarbons recovery efficiency and allows reaching lower limits of detection of the whole analytical system. The presented desorber seems to be very attractive alternative over widely used mechanical desorbers.

  2. Influence of dust and mud on the optical, chemical, and mechanical properties of a pv protective glass.

    Science.gov (United States)

    Yilbas, Bekir Sami; Ali, Haider; Khaled, Mazen M; Al-Aqeeli, Nasser; Abu-Dheir, Numan; Varanasi, Kripa K

    2015-10-30

    Recent developments in climate change have increased the frequency of dust storms in the Middle East. Dust storms significantly influence the performances of solar energy harvesting systems, particularly (photovoltaic) PV systems. The characteristics of the dust and the mud formed from this dust are examined using various analytical tools, including optical, scanning electron, and atomic force microscopies, X-ray diffraction, energy spectroscopy, and Fourier transform infrared spectroscopy. The adhesion, cohesion and frictional forces present during the removal of dry mud from the glass surface are determined using a microtribometer. Alkali and alkaline earth metal compounds in the dust dissolve in water to form a chemically active solution at the glass surface. This solution modifies the texture of the glass surface, thereby increasing the microhardness and decreasing the transmittance of the incident optical radiation. The force required to remove the dry mud from the glass surface is high due to the cohesive forces that result from the dried mud solution at the interface between the mud and the glass. The ability altering the characteristics of the glass surface could address the dust/mud-related limitations of protective surfaces and has implications for efficiency enhancements in solar energy systems.

  3. Closure Report for Corrective Action Unit 357: Mud Pits and Waste Dump, Nevada Test Site, Nevada, Rev. No.: 0

    Energy Technology Data Exchange (ETDEWEB)

    Laura A. Pastor

    2005-04-01

    This Closure Report (CR) presents information supporting closure of Corrective Action Unit (CAU) 357: Mud Pits and Waste Dump, Nevada Test Site (NTS), Nevada. The CR complies with the requirements of the Federal Facility Agreement and Consent Order (FFACO) that was agreed to by the State of Nevada, U.S. Department of Energy (DOE), and the U.S. Department of Defense (FFACO, 1996). Corrective Action Unit 357 is comprised of 14 Corrective Action Sites (CASs) located in Areas 1, 4, 7, 8, 10, and 25 of the NTS (Figure 1-1). The NTS is located approximately 65 miles (mi) northwest of Las Vegas, Nevada. Corrective Action Unit 357 consists of 11 CASs that are mud pits located in Areas 7, 8, and 10. The mud pits were associated with drilling activities conducted on the NTS in support of the underground nuclear weapons testing. The remaining three CASs are boxes and pipes associated with Building 1-31.2el, lead bricks, and a waste dump. These CAS are located in Areas 1, 4, and 25, respectively. The following CASs are shown on Figure 1-1: CAS 07-09-02, Mud Pit; CAS 07-09-03, Mud Pit; CAS 07-09-04, Mud Pit; CAS 07-09-05, Mud Pit; CAS 08-09-01, Mud Pit; CAS 08-09-02, Mud Pit; CAS 08-09-03, Mud Pit; CAS 10-09-02, Mud Pit; CAS 10-09-04, Mud Pit; CAS 10-09-05, Mud Pit; CAS 10-09-06, Mud Pit, Stains, Material; CAS 01-99-01, Boxes, Pipes; CAS 04-26-03, Lead Bricks; and CAS 25-15-01, Waste Dump. The purpose of the corrective action activities was to obtain analytical data that supports the closure of CAU 357. Environmental samples were collected during the investigation to determine whether contaminants exist and if detected, their extent. The investigation and sampling strategy was designed to target locations and media most likely to be contaminated (biased sampling). A general site conceptual model was developed for each CAS to support and guide the investigation as outlined in the Streamlined Approach for Environmental Restoration (SAFER) Plan (NNSA/NSO, 2003b). This CR

  4. Origin of Fluids and Salts at Mercator Mud Vulcano, Gulf of Cadiz

    OpenAIRE

    Katja Heeschen; M. Haeckel; C. Berndt; D. Teagle; M. Palmer; D. Green; M. Cooper; H. Vaneste; V. Liebetrau

    2008-01-01

    The Gulf of Cadiz is located at the plate boundary between the Eurasian and African plates and is characterized by widespread mud volcanism all along the continental margins. It is commonly believed that this results from sediment dewatering enhanced by the compressional forces within the accretionary prism. Recently, 3D seismic data and geochemical sediment cores indicated that in addition to compressional tectonics, halokinesis controls the location and dynamics of the Mercator mud volca...

  5. Preadolescent Girls' and Boys' Virtual MUD Play

    Science.gov (United States)

    Calvert, Sandra L.; Strouse, Gabrielle A.; Strong, Bonnie L.; Huffaker, David A.; Lai, Sean

    2009-01-01

    Same and opposite-sex pairs of preadolescents interacted twice in a MUD, a virtual domain where they created characters known as avatars and socially interacted with one another. Boys interacted primarily through rapid scene shifts and playful exchanges; girls interacted with one another through written dialogue. Opposite-sex pairs lagged behind…

  6. Distribution of effluent injected into the Boulder Zone of the Floridan aquifer system at the North District Wastewater Treatment Plant, southeastern Florida, 1997–2011

    Science.gov (United States)

    King, Jeffrey N.; Decker, Jeremy D.

    2018-02-09

    Nonhazardous, secondarily treated, domestic wastewater (effluent) has been injected about 1 kilometer below land surface into the Boulder Zone of the Floridan aquifer system at the North District Wastewater Treatment Plant in southeastern Florida. The Boulder Zone contains saline, nonpotable water. Effluent transport out of the injection zone is a risk of underground effluent injection. At the North District Wastewater Treatment Plant, injected effluent was detected outside the Boulder Zone. The U.S. Geological Survey, in cooperation with Miami-Dade Water and Sewer Department, investigated effluent transport from the Boulder Zone to overlying permeable zones in the Floridan aquifer system.One conceptual model is presented to explain the presence of effluent outside of the injection zone in which effluent injected into the Boulder Zone was transported to the Avon Park permeable zone, forced by buoyancy and injection pressure. In this conceptual model, effluent injected primarily into the Boulder Zone reaches a naturally occurring feature (a karst-collapse structure) near an injection well, through which the effluent is transported vertically upward to the uppermost major permeable zone of the Lower Floridan aquifer. The effluent is then transported laterally through the uppermost major permeable zone of the Lower Floridan aquifer to another naturally occurring feature northwest of the North District Wastewater Treatment Plant, through which it is then transported vertically upward into the Avon Park permeable zone. In addition, a leak within a monitoring well, between monitoring zones, allowed interflow between the Avon Park permeable zone and the Upper Floridan aquifer. A groundwater flow and effluent transport simulation of the hydrogeologic system at the North District Wastewater Treatment Plant, based on the hypothesized and non-unique conceptualization of the subsurface hydrogeology and flow system, generally replicated measured effluent constituent

  7. Armoured mud balls as a result of ephemeral fluvial flood in a humid climate: Modern example from Guizhou Province, South China

    Directory of Open Access Journals (Sweden)

    Gerhard H. Bachmann

    2014-10-01

    Full Text Available Armoured mud balls were observed after rainfall and a short flood in the otherwise dry Xiaohe (small river valley of Guanling County, Guizhou Province, South China, approximately 30 km southwest of Guanling City. Armoured mud balls are most common in semiarid climates, but rather unusual in a humid climate as in Guizhou. A number of well-rounded mud balls, 2–20 cm in diameter, were found lying on the gravel of the Xiaohe gully floor. The mud balls consist of sticky, light brown and slightly mottled clay without carbonate content. The surfaces of the mud balls were studded with rims of sand- or gravel-size limestone clasts, collected during bedload transport, as is typical for armoured mud balls. The mud balls originated from alluvial mudstone deposits of the valley floor and cliff that are most likely derived from the weathering and karstification of bedrock limestones. Such mudstones with high clay content seem to be especially well suited for forming armoured mud balls. As flood events are rather common in the area, the formation of armoured mud balls should be very frequent in the Xiaohe valley and similar valleys nearby, giving the possibility for further and more detailed studies. To the best of our knowledge this is the first description of armoured mud balls in China.

  8. Study of a large rapid ashing apparatus and a rapid dry ashing method for biological samples and its application

    International Nuclear Information System (INIS)

    Jin Meisun; Wang Benli; Liu Wencang

    1988-04-01

    A large rapid-dry-ashing apparatus and a rapid ashing method for biological samples are described. The apparatus consists of specially made ashing furnace, gas supply system and temperature-programming control cabinet. The following adventages have been showed by ashing experiment with the above apparatus: (1) high speed of ashing and saving of electric energy; (2) The apparatus can ash a large amount of samples at a time; (3) The ashed sample is pure white (or spotless), loose and easily soluble with few content of residual char; (4) The fresh sample can also be ashed directly. The apparatus is suitable for ashing a large amount of the environmental samples containing low level radioactivity trace elements and the medical, food and agricultural research samples

  9. A Mineralogical Assessment on Residues after Acidic Leaching of Bauxite Residue (Red Mud) for Titanium Recovery

    OpenAIRE

    Gözde Alkan; Claudia Schier; Lars Gronen; Srecko Stopic; Bernd Friedrich

    2017-01-01

    Due to its alkalinity, red mud produced by the Bayer process may affect both the environment and human health. For this reason, its further utilization instead of disposal is of great importance. Numerous methods have already been studied for hydrometallurgical treatment of red mud, especially for the recovery of various metallic components such as iron, aluminum, titanium or rare earth elements. This study focuses on the extraction of titanium from red mud and in particular the mineralogical...

  10. Experimental investigation of the influence of nanoparticles on water-based mud

    Science.gov (United States)

    Dhiman, Paritosh; Cheng, Yaoze; Zhang, Yin; Patil, Shirish

    2018-03-01

    This study has investigated the influence of nanoparticles including nanoparticle concentration, size, and type on water-based mud (WBM) properties including rheology, filtration, and lubricity through experimental tests, while the influence of temperature and aging on these properties have been investigated. It has been found that adding SiO2 nanoparticles increase the plastic viscosity and decrease the yield points and gel strengths with the increase of nanoparticle concentration. At fixed 0.5 wt%, the plastic viscosity decreases with the increase of TiO2 nanoparticle size, but the influence of TiO2 nanoparticle size on yield points and gel strengths is not monotonous. In general, adding negative charged SiO2 nanoparticles reduce the yield points and gel strengths, while adding positively charged TiO2, Al2O3, and Fe3O4 nanoparticles increase yield points and gel strengths. Adding lower concentrations (mud filtration and lubricity properties, but higher concentrations are adverse to these properties and adding 0.5 wt% TiO2, Al2O3 and Fe3O4 nanoparticles impaired these properties. Besides, it is found that there is no consistent influence of aging on mud properties and adding nanoparticles cannot improve aging resistance of mud. Although adding nanoparticles can significantly affect WBM properties, their influences are not consistency, depending on the integrated impact of the nanoparticle properties, such as surface electrical property, specific surface area, concentration, and size.

  11. Volcanic ash impacts on critical infrastructure

    Science.gov (United States)

    Wilson, Thomas M.; Stewart, Carol; Sword-Daniels, Victoria; Leonard, Graham S.; Johnston, David M.; Cole, Jim W.; Wardman, Johnny; Wilson, Grant; Barnard, Scott T.

    2012-01-01

    Volcanic eruptions can produce a wide range of hazards. Although phenomena such as pyroclastic flows and surges, sector collapses, lahars and ballistic blocks are the most destructive and dangerous, volcanic ash is by far the most widely distributed eruption product. Although ash falls rarely endanger human life directly, threats to public health and disruption to critical infrastructure services, aviation and primary production can lead to significant societal impacts. Even relatively small eruptions can cause widespread disruption, damage and economic loss. Volcanic eruptions are, in general, infrequent and somewhat exotic occurrences, and consequently in many parts of the world, the management of critical infrastructure during volcanic crises can be improved with greater knowledge of the likely impacts. This article presents an overview of volcanic ash impacts on critical infrastructure, other than aviation and fuel supply, illustrated by findings from impact assessment reconnaissance trips carried out to a wide range of locations worldwide by our international research group and local collaborators. ‘Critical infrastructure’ includes those assets, frequently taken for granted, which are essential for the functioning of a society and economy. Electricity networks are very vulnerable to disruption from volcanic ash falls. This is particularly the case when fine ash is erupted because it has a greater tendency to adhere to line and substation insulators, where it can cause flashover (unintended electrical discharge) which can in turn cause widespread and disruptive outages. Weather conditions are a major determinant of flashover risk. Dry ash is not conductive, and heavy rain will wash ash from insulators, but light rain/mist will mobilise readily-soluble salts on the surface of the ash grains and lower the ash layer’s resistivity. Wet ash is also heavier than dry ash, increasing the risk of line breakage or tower/pole collapse. Particular issues for water

  12. Behavioural changes of Atlantic cod (Gadus morhua) after marine boulder reef restoration: Implications for coastal habitat management and Natura 2000 areas

    DEFF Research Database (Denmark)

    Støttrup, Josianne Gatt; Svendsen, Jon Christian; Stenberg, Claus

    2017-01-01

    While marine reefs are degraded globally, the responses of fish to marine reef restoration remain uncertain, particularly in temperate waters. This study measured the effect of marine boulder reef restoration on the behaviour of Atlantic cod, Gadus morhua L., in a Natura 2000 area using acoustic...... telemetry. Cod were tagged and released in the study area before and after the restoration and tracked continuously for six months. A larger fraction of the released fish remained in the study area after restoration (94%) than before (53%). Moreover, throughout the study period, cod spent significantly more...... hours per day and prolonged their residence time in the study area after the restoration. The study indicates that marine reefs subjected to boulder extraction can be restored and function as favourable cod habitats. Temperate marine boulder reef restoration represents a valuable management tool...

  13. Predicted Versus Actual Savings for a Low-Rise Multifamily Retrofit in Boulder, Colorado

    Energy Technology Data Exchange (ETDEWEB)

    Arena, L. [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States); Williamson, J. [Consortium for Advanced Residential Buildings (CARB), Norwalk, CT (United States)

    2013-11-01

    To determine the most cost-effective methods of improving buildings, accurate analysis and prediction of the energy use of existing buildings is essential. However, multiple studies confirm that analysis methods tend to over-predict energy use in poorly insulated, leaky homes and thus, the savings associated with improving those homes. In this project, the Building America CARB team evaluated the retrofit of a multifamily building in Boulder, CO. The updated property is a 37 unit, 2 story apartment complex built in 1950, which underwent renovations in early 2009 to bring it into compliance with Boulder, CO's SmartRegs ordinance. Goals of the study were to: 1) evaluate predicted versus actual savings due to the improvements, 2) identify areas where the modeling assumptions may need to be changed, and 3) determine common changes made by renters that would negatively impact energy savings. Other issues that were investigated include the effects of improving building efficiency on tenant comfort, the impact on tenant turnover rates, and the potential market barriers for this type of community scale project.

  14. Analysis of the bacterial community in aged and aging pit mud of Chinese Luzhou-flavour liquor by combined PCR-DGGE and quantitative PCR assay.

    Science.gov (United States)

    Liang, Huipeng; Li, Wenfang; Luo, Qingchun; Liu, Chaolan; Wu, Zhengyun; Zhang, Wenxue

    2015-10-01

    The community structure of bacteria in aged and aging pit mud, which was judged according to their sensory and physicochemical characteristics, was analysed using polymerase chain reaction denaturing gradient gel electrophoresis (PCR-DGGE) and quantitative real-time PCR (qPCR). The phyla Firmicutes, Actinobacteria, Proteobacteria, Synergistetes and Unclassified Bacteria were detected and the fermentative Firmicutes was predominant in both types of pit mud in the PCR-DGGE analysis. Among Firmicutes, Clostridiales was dominant in aged pit mud while Bacillales and Lactobacillales were dominant in aging pit mud. The diversity of bacterial communities in aged pit mud was higher than that in aging pit mud. In the qPCR analysis the abundance of Clostridium IV in aged pit mud was higher than that in aging pit mud and there were significant differences in the quantity of Clostridium IV between aged and aging pit mud of the same cellar (P mud. The differences in the quantity of Clostridium IV might be involved in the distinction that the aged pit mud has a strong aroma while the aging pit mud does not. © 2014 Society of Chemical Industry.

  15. Transcriptomic signatures of ash (Fraxinus spp. phloem.

    Directory of Open Access Journals (Sweden)

    Xiaodong Bai

    2011-01-01

    Full Text Available Ash (Fraxinus spp. is a dominant tree species throughout urban and forested landscapes of North America (NA. The rapid invasion of NA by emerald ash borer (Agrilus planipennis, a wood-boring beetle endemic to Eastern Asia, has resulted in the death of millions of ash trees and threatens billions more. Larvae feed primarily on phloem tissue, which girdles and kills the tree. While NA ash species including black (F. nigra, green (F. pennsylvannica and white (F. americana are highly susceptible, the Asian species Manchurian ash (F. mandshurica is resistant to A. planipennis perhaps due to their co-evolutionary history. Little is known about the molecular genetics of ash. Hence, we undertook a functional genomics approach to identify the repertoire of genes expressed in ash phloem.Using 454 pyrosequencing we obtained 58,673 high quality ash sequences from pooled phloem samples of green, white, black, blue and Manchurian ash. Intriguingly, 45% of the deduced proteins were not significantly similar to any sequences in the GenBank non-redundant database. KEGG analysis of the ash sequences revealed a high occurrence of defense related genes. Expression analysis of early regulators potentially involved in plant defense (i.e. transcription factors, calcium dependent protein kinases and a lipoxygenase 3 revealed higher mRNA levels in resistant ash compared to susceptible ash species. Lastly, we predicted a total of 1,272 single nucleotide polymorphisms and 980 microsatellite loci, among which seven microsatellite loci showed polymorphism between different ash species.The current transcriptomic data provide an invaluable resource for understanding the genetic make-up of ash phloem, the target tissue of A. planipennis. These data along with future functional studies could lead to the identification/characterization of defense genes involved in resistance of ash to A. planipennis, and in future ash breeding programs for marker development.

  16. Geochemistry of mud volcano fluids in the Taiwan accretionary prism

    International Nuclear Information System (INIS)

    You Chenfeng; Gieskes, Joris M.; Lee, Typhoon; Yui Tzenfu; Chen Hsinwen

    2004-01-01

    Taiwan is located at the collision boundary between the Philippine Sea Plate and the Asian Continental Plate and is one of the most active orogenic belts in the world. Fluids sampled from 9 sub-aerial mud volcanoes distributed along two major geological structures in southwestern Taiwan, the Chishan fault and the Gutingkeng anticline, were analyzed to evaluate possible sources of water and the degree of fluid-sediment interaction at depth in an accretionary prism. Overall, the Taiwanese mud volcano fluids are characterized by high Cl contents, up to 347 mM, suggesting a marine origin from actively de-watering sedimentary pore waters along major structures on land. The fluids obtained from the Gutingkeng anticline, as well as from the Coastal Plain area, show high Cl, Na, K, Ca, Mg and NH 4 , but low SO 4 and B concentrations. In contrast, the Chishan fault fluids are much less saline (1/4 seawater value), but show much heavier O isotope compositions (δ 18 O=5.1-6.5 %o). A simplified scenario of mixing between sedimentary pore fluids and waters affected by clay dehydration released at depth can explain several crucial observations including heavy O isotopes, radiogenic Sr contents ( 87 Sr/ 86 Sr=0.71136-0.71283), and relatively low salinities in the Chishan fluids. Gases isolated from the mud volcanoes are predominantly CH 4 and CO 2 , where the CH 4 -C isotopic compositions show a thermogenic component of δ 13 C=-38 %o. These results demonstrate that active mud volcano de-watering in Taiwan is a direct product of intense sediment accretion and plate collision in the region

  17. Spectral analysis of white ash response to emerald ash borer infestations

    Science.gov (United States)

    Calandra, Laura

    The emerald ash borer (EAB) (Agrilus planipennis Fairmaire) is an invasive insect that has killed over 50 million ash trees in the US. The goal of this research was to establish a method to identify ash trees infested with EAB using remote sensing techniques at the leaf-level and tree crown level. First, a field-based study at the leaf-level used the range of spectral bands from the WorldView-2 sensor to determine if there was a significant difference between EAB-infested white ash (Fraxinus americana) and healthy leaves. Binary logistic regression models were developed using individual and combinations of wavelengths; the most successful model included 545 and 950 nm bands. The second half of this research employed imagery to identify healthy and EAB-infested trees, comparing pixel- and object-based methods by applying an unsupervised classification approach and a tree crown delineation algorithm, respectively. The pixel-based models attained the highest overall accuracies.

  18. Meteorological Uncertainty of atmospheric Dispersion model results (MUD)

    DEFF Research Database (Denmark)

    Havskov Sørensen, Jens; Amstrup, Bjarne; Feddersen, Henrik

    The MUD project addresses assessment of uncertainties of atmospheric dispersion model predictions, as well as optimum presentation to decision makers. Previously, it has not been possible to estimate such uncertainties quantitatively, but merely to calculate the 'most likely' dispersion scenario....

  19. Thermal treatment of ashes[Fly Ash from Municipal Waste Incineration]; Termisk rening av askor

    Energy Technology Data Exchange (ETDEWEB)

    Wikman, Karin; Berg, Magnus; Bjurstroem, Henrik [AaF-Energi och Miljoe AB, Stockholm (Sweden); Nordin, Anders [Umeaa Univ. (Sweden). Dept. of Applied Physics and Electronics

    2003-04-01

    In this project descriptions of different processes for thermal treatment of ashes have been compiled. A technical and economic evaluation of the processes has been done to identify possibilities and problems. The focus in the project lays on treatment of fly ash from municipal waste incineration but the processes can also be used to treat other ashes. When the ash is heated in the thermal treatment reactor, with or without additives, the material is sintered or vitrified and at the same time volatile substances (Zn, Pb, Cd, Hg etc.) are separated. In general the separation is more effective in processes with reducing conditions compared to oxidizing conditions. Oxidizing processes have both worse separation capacity and require more energy. The oxidizing processes are mainly used to stabilize the ash through vitrification and they are in some cases developed for management of municipal sewage sludge and bottom ash. However, these processes are often not as complex as for example an electric arc melting furnace with reducing conditions. The research today aim to develop more effective electrical melting systems with reducing conditions such as plasma melting furnaces, electric resistance melting furnaces and low frequency induction furnaces. A central question in the evaluation of different thermal treatment processes for ash is how the residues from the treatment can be used. It is not certain that the vitrified material is stable enough to get a high economic value, but it can probably be used as construction material. How the remaining metals in the ash are bound is very important in a long-time perspective. Further studies with leaching tests are necessary to clarify this issue. The heavy metal concentrate from the processes contains impurities, such as chlorine, which makes it unprofitable to obtain the metals. Instead the heavy metal concentrate has to be land filled. However, the amount of material for land filling will be much smaller if only the heavy

  20. Electron microscopy study of red mud after seawater neutralisation

    International Nuclear Information System (INIS)

    Toledo, S.P.; Kiyohara, P.K.; Antunes, M.L.P.; Frost, Ray

    2012-01-01

    Red Mud, residue of Bayer process for extracting alumina from bauxite, is produced in large quantity. This residue is very alkaline and can cause damage to health and the environment. One way to minimize the environmental impact of this residue is neutralization by sea water. The Brazilian Red Mud was treated with sea water. It appears that the initial pH of the samples is reduced to 8. The analysis by x-ray diffraction allows to identify the formation of hydrotalcite and aragonite. The transmission electron microscopy images show that this consists of particles with dimensions between 0.02 to 2 μm. It was possible to identify by EDS/MET particles of magnesium, confirming the formation of hydrotalcite. (author)

  1. Immobilization of copper flotation waste using red mud and clinoptilolite.

    Science.gov (United States)

    Coruh, Semra

    2008-10-01

    The flash smelting process has been used in the copper industry for a number of years and has replaced most of the reverberatory applications, known as conventional copper smelting processes. Copper smelters produce large amounts of copper slag or copper flotation waste and the dumping of these quantities of copper slag causes economic, environmental and space problems. The aim of this study was to perform a laboratory investigation to assess the feasibility of immobilizing the heavy metals contained in copper flotation waste. For this purpose, samples of copper flotation waste were immobilized with relatively small proportions of red mud and large proportions of clinoptilolite. The results of laboratory leaching demonstrate that addition of red mud and clinoptilolite to the copper flotation waste drastically reduced the heavy metal content in the effluent and the red mud performed better than clinoptilolite. This study also compared the leaching behaviour of metals in copper flotation waste by short-time extraction tests such as the toxicity characteristic leaching procedure (TCLP), deionized water (DI) and field leach test (FLT). The results of leach tests showed that the results of the FLT and DI methods were close and generally lower than those of the TCLP methods.

  2. Suspended matter and fluid mud off Alleppey, southwest coast of India

    Digital Repository Service at National Institute of Oceanography (India)

    Shynu, R.; Rao, V.P.; Samiksha, S.V.; Vethamony, P.; Naqvi, S.W.A.; Kessarkar, P.M.; Babu, M.T.; DineshKumar, P.K.

    ‘Alleppey Mudbank Process Studies (AMPS)’ during April-September 2014. Three stations (M1, M2 and M3; Fig. 1)3 to 3.5 km away from the coastwere selected for systematic time series data collection. Station M1 is located in the non-mud bank region. Station.... It is likely more than one process is involved in the formation of fluid mud. Acknowledgments The ‘Alleppey Mudbank Process Studies (AMPS-2014)’ has resulted from an initiative of the Director, CSIR-NIO. A series of discussions held with several colleagues...

  3. Application of Coal Ash to Postmine Land for Prevention of Soil Erosion in Coal Mine in Indonesia: Utilization of Fly Ash and Bottom Ash

    Directory of Open Access Journals (Sweden)

    Shinji Matsumoto

    2016-01-01

    Full Text Available The increase in the number of coal-fired power plants with the increase in coal production and its consumption has caused the problem of the treatment of a large amount of coal ash in Indonesia. In the past studies, coal ash was applied to postmine land with the aim of improving soil conditions for plant growth; however, heavy rain in the tropical climate may cause soil erosion with the change in soil conditions. This study presents the effects of application of coal ash to postmine land on soil erosion by performing the artificial rainfall test as well as physical testing. The results indicate that the risk of soil erosion can be reduced significantly by applying the coal ash which consists of more than 85% of sand to topsoil in the postmine land at the mixing ratio of over 30%. Additionally, they reveal that not only fine fractions but also microporous structures in coal ash enhance water retention capacity by retaining water in the structure, leading to the prevention of soil erosion. Thus, the risk of soil erosion can be reduced by applying coal ash to topsoil in consideration of soil composition and microporous structure of coal ash.

  4. Influence of solids concentration on the sedimentation rate of the mud in the aggregate industry

    Directory of Open Access Journals (Sweden)

    Benigno Leyva-de la Cruz

    2016-12-01

    Full Text Available The objective of this investigation is to determine, for the mud resulting from the wash process in the Jobo community arid industry in Sagua de Tánamo, the impact of solids percent on the theoretical sedimentation velocity that is predicted by the Stokes velocity Law. Samples of the discharge pipeline and the mud sedimentation area were analyzed from granulometric, density and solids concentration points of view. The solids percentage variable (S was analyzed in four scenarios (4, 12, 20 and 28 % and time (t was evaluated at intervals of 20 minutes for 5 hours. The behavior of mud sedimentation was characterized through the sedimentation velocity. The results indicate that the Stokes velocity law does not apply for estimating the mud sedimentation velocity with a 95% confidence. Therefore, a correction function is obtained for the Stokes velocity law expressed through the polynomial mathematical model of second degree.

  5. Effects of drilling muds on behavior of the American lobster, Homarus americanus, in water column and substrate exposures

    Energy Technology Data Exchange (ETDEWEB)

    Atema, J; Leavitt, D F; Barshaw, D E; Cuomo, M C

    1982-01-01

    Studies were conducted to explore the effects of drilling muds on various aspects of lobster behavior directly related to survival in the field. Toxicity of different drilling muds varied from immediately lethal to adult lobsters to apparently harmless to postlarval stages, with a variety of intermediate effects. Both the chemical toxicity in the water column and the physical effects of covering the substrate with drilling mud were studied, and both interfered with normal lobster behavior. The studies are mainly concerned with postlarval lobsters (stages IV and V), just after settling on the bottom. They were tested in 36-d chronic exposures (7 mg/L) and in seminatural aquaria with 1-mm layers of drilling mud covering the substrate. Toxicity in the water column manifested itself in feeding and molting delays, severe delays in shelter construction, increased walking and swimming, unprovoked tail flipping, and lethargy. A natural bay mud used as a control caused no such effects. Physical effects of substrate cover were apparent in experiments with 1-, 2-, and 4-mm layers of drilling mud and similar layers of a mixture of bentonite and barite covering a natural mud substrate. In depths of 4mm both kinds of substrate cover caused severe delays in shelter construction and in quality of burrows constructed. Thus, substrates with 4-mm to perhaps as little as 1-mm covering of drilling mud may cause increased exposure of lobsters to predators and currents, resulting in the substrate becoming unsuitable for lobster settling and survival.

  6. Comparison of authigenic carbonates formation at mud volcanoes and pockmarks in the Portuguese Margin vs. at the Yinazao serpentinite mud volcano in the Marianas forearc

    Science.gov (United States)

    Magalhaes, V. H.; Freitas, M.; Azevedo, M. R.; Pinheiro, L. M.; Salgueiro, E.; Abrantes, F. F. G.

    2017-12-01

    On the Portuguese passive continental margin, active and past seepage processes form mud volcanoes and pockmarks at the seafloor. Often associated with these structures are extensive methane-derived authigenic carbonates that form from deep-sourced methane-rich fluids that ascend from deep to the upper sedimentary column and often discharge at the seafloor. These carbonates form within the sediments and are either dominated by dolomite and high-Mg calcites, when formed under a restricted seawater circulation environment, anoxic and low sulphate conditions; or by aragonite and calcite when formed close to or at the seafloor in a high sulphate system. The δ13C values (-56.2‰ VPDB) found on the carbonate-cemented material clearly indicates methane as the major carbon source. On the Yinazao serpentinite mud volcano at an active, non-accretionary, convergent margin, sediment samples from IODP Sites U1491 and U1492 (Exp. 366) contain authigenic minerals such as aragonite, calcite, brucite, gypsum among others. Authigenic aragonite occurs predominantly within the top meters of the cores where both oxidation and seawater circulation in the sedimentary column are higher. In this system, initial results indicate that the major carbon source is most probably not methane but seawater related. This work discusses and compares the major carbon sources in both systems: sedimentary mud volcanoes and pockmarks of a passive margin vs. a serpentinite mud volcano of an active, non-accretionary, convergent margin. We acknowledge the support from the PES project - Pockmarks and fluid seepage in the Estremadura Spur: implications for regional geology, biology, and petroleum systems (PTDC/GEOFIQ/5162/2014) financed by the Portuguese Foundation for Science and Technology (FCT).

  7. [Sulphureous mud-bath therapy and changes in blood pressure: observational investigation].

    Science.gov (United States)

    Costantino, M; Marongiu, M B; Russomanno, G; Conti, V; Manzo, V; Filippelli, A

    2015-01-01

    The chronic arthropathies currently appear to be a major cause of disability with a negative impact on quality of life and health care spending. The mud-bath therapy is a spa treatment that induces benefic effects in chronic rheumatic diseases. It has long been debated on the assumption that the mud-bath spa therapy could have adverse cardiovascular effects which often induce caution and even a contraindication to the use of this treatment in chronic arthropathies associated with cardiovascular alterations such as hypertension. The aim of this observational study was to investigate, in arthrorheumatic subjects, the effects of sulphureous mud-bath cycle on blood pressure and the possible appearance of adverse drug reaction. 169 patients, with age range 42-86 years, suffering by chronic arthropathies were treated with sulphureous mud-bath therapy for 2 weeks. According to the arterial pressure values, measured before the spa treatment, the patients considered were divided in three groups: with normal blood pressure (NOR group); with high blood pressure, after, the latter group was divided in IPET (patients in treatment with antihypertensive drugs) and IPENT (patients not in antihypertensive therapy). The arterial pressure values, maximum and minimum, expressed in mmHg, were detected in the first (T1) - sixth (T6) and twelfth (T12) day of spa treatment. The media arterial pressure values collected before and after T1, before and after T6, before and after T12 , before T1 and after T12 were compared. The data, presented as mean±SD, were compared with the paired Student t test. A p value ≤0.05 was considered significant. The comparison between the mean values detected in pre and post T1, pre and post T6, pre and post T12 have showed that sulphureous mud-bath therapy induced a significant (pmud-bath therapy (post-T12) vs baseline (pre-T1) have demonstrated: in IPET and IPENT groups a significant (pmud-bath therapy in interdisciplinary therapeutic p rotocol of patients

  8. Possibilities of utilizing power plant fly ashes

    Directory of Open Access Journals (Sweden)

    Mezencevová Andrea

    2003-09-01

    Full Text Available The burning of fossil fuels in industrial power stations plays a significant role in the production of thermal and electrical energy. Modern thermal power plants are producing large amounts of solid waste, mainly fly ashes. The disposal of power plant waste is a large environmental problem at the present time. In this paper, possibilities of utilization of power plant fly ashes in industry, especially in civil engineering, are presented. The fly ash is a heterogeneous material with various physical, chemical and mineralogical properties, depending on the mineralogical composition of burned coal and on the used combustion technology. The utilization of fly ashes is determined of their properties. The fineness, specific surface area, particle shape, density, hardness, freeze-thaw resistance, etc. are decisive. The building trade is a branch of industry, which employs fly ash in large quantities for several decades.The best utilization of fluid fly ashes is mainly in the production of cement and concrete, due to the excellent pozzolanic and cementitious properties of this waste. In the concrete processing, the fly ash is utilized as a replacement of the fine aggregate (fine filler or a partial replacement for cement (active admixture. In addition to economic and ecological benefits, the use of fly ash in concrete improves its workability and durability, increases compressive and flexural strength, reduces segregation, bleeding, shrinkage, heat evolution and permeability and enhances sulfate resistance of concrete.The aim of current research is to search for new technologies for the fly ash utilization. The very interesting are biotechnological methods to recovery useful components of fly ashes and unconventional methods of modification of fly ash properties such as hydrothermal zeolitization and mechanochemical modification of its properties. Mechanochemistry deals with physico - chemical transformations and chemical reactions of solids induced by

  9. Topicality and possibilities for complete processing of red mud of aluminous production

    Directory of Open Access Journals (Sweden)

    В. Л. Трушко

    2017-10-01

    Full Text Available In the aluminum industry, the largest amount of waste is red mud (RM. that is a solid bauxite residue after hydrochemical processing and extraction of alumina. The topicality of its processing was shown by the ecological catastrophe in Hungary (2010, where the bund wall of the slurry storage was destroyed and the viscous mass of fine red mud fell on thousands of hectares of land.The risks of a recurrence of such a catastrophe increase due to the increased natural disasters: earthquakes, torrential rains and floods, as well as terrorist attacks. Therefore, it is proposed to exclude the storage of red mud in sludge storages and organize its shipment in transportable form to processing complexes.The article presents the results of scientific research and the experience of complex processing of red sludge on an industrial scale with the production of new types of marketable products.

  10. THE USE OF MUD "TINAKSKAYA" IN MEDICINE (LITERATURE REVIEW

    Directory of Open Access Journals (Sweden)

    Z. A. Tsurigova

    2015-01-01

    Full Text Available This review summarizes the published data on the therapeutic properties of the mud "Tinakskaya". In addition, data on the use of natural factors lake "Therapeutic" in medicine is performed.

  11. Measurement of natural activity in peat ashes

    International Nuclear Information System (INIS)

    Suomela, J.

    1985-01-01

    High proportions of radioactive materials in peat ashes may involve radiation hazards during handling and deposition of these waste materials. Measurements have been performed to determine the content of radioactive materials in ashes from peat burning. The activities in fly ash and ''solid'' ash in seven peat-fired power plants in Sweden are presented. The methods of analysing and measuring peat ashes for activity from different radionuclides are described. The activity levels in ash samples are given

  12. Meteorological Uncertainty of atmospheric Dispersion model results (MUD)

    DEFF Research Database (Denmark)

    Havskov Sørensen, Jens; Amstrup, Bjarne; Feddersen, Henrik

    The MUD project addresses assessment of uncertainties of atmospheric dispersion model predictions, as well as possibilities for optimum presentation to decision makers. Previously, it has not been possible to estimate such uncertainties quantitatively, but merely to calculate the ‘most likely’ di...

  13. Classification of pulverized coal ash

    International Nuclear Information System (INIS)

    Van der Sloot, H.A.; Van der Hoek, E.E.; De Groot, G.J.; Comans, R.N.J.

    1992-09-01

    The leachability of fifty different pulverized coal ashes from utilities in the Netherlands, Federal Republic of Germany and Belgium has been studied. Five different ashes were analyzed according to the complete standard leaching test and the results were published earlier. The examination of a wide variety of ashes under a wide range of pH and Liquid to Solid ratio (LS) conditions creates the possibility of identifying systematic trends in fly ash leaching behaviour and to identify the mechanisms controlling release. 16 figs., 2 tabs., 3 app., 25 refs

  14. Practical application of failure criteria in determining safe mud weight windows in drilling operations

    Directory of Open Access Journals (Sweden)

    R. Gholami

    2014-02-01

    Full Text Available Wellbore instability is reported frequently as one of the most significant incidents during drilling operations. Analysis of wellbore instability includes estimation of formation mechanical properties and the state of in situ stresses. In this analysis, the only controllable parameter during drilling operation is the mud weight. If the mud weight is larger than anticipated, the mud will invade into the formation, causing tensile failure of the formation. On the other hand, a lower mud weight can result in shear failures of rock, which is known as borehole breakouts. To predict the potential for failures around the wellbore during drilling, one should use a failure criterion to compare the rock strength against induced tangential stresses around the wellbore at a given mud pressure. The Mohr–Coulomb failure criterion is one of the commonly accepted criteria for estimation of rock strength at a given state of stress. However, the use of other criteria has been debated in the literature. In this paper, Mohr–Coulomb, Hoek–Brown and Mogi–Coulomb failure criteria were used to estimate the potential rock failure around a wellbore located in an onshore field of Iran. The log based analysis was used to estimate rock mechanical properties of formations and state of stresses. The results indicated that amongst different failure criteria, the Mohr–Coulomb criterion underestimates the highest mud pressure required to avoid breakouts around the wellbore. It also predicts a lower fracture gradient pressure. In addition, it was found that the results obtained from Mogi–Coulomb criterion yield a better comparison with breakouts observed from the caliper logs than that of Hoek–Brown criterion. It was concluded that the Mogi–Coulomb criterion is a better failure criterion as it considers the effect of the intermediate principal stress component in the failure analysis.

  15. Radioactivity of wood ash; Puun tuhkan radioaktiivisuus

    Energy Technology Data Exchange (ETDEWEB)

    Rantavaara, A.; Moring, M

    2000-01-01

    STUK (Finnish Radiation and Nuclear Safety Authority) has investigated natural and artificial radioactivity in wood ash and radiation exposure from radionuclides in ash since 1996. The aim was to consider both handling of ash and different ways of using ash. In all 87 ash samples were collected from 22 plants using entirely or partially wood for their energy production in 1996-1997. The sites studied represented mostly chemical forest industry, sawmills or district heat production. Most plants used fluidised bed combustion technique. Samples of both fly ash and bottom ash were studied. The activity concentrations of radionuclides in samples of, e.g., dried fly ash from fuel containing more than 80% wood were determined. The means ranged from 2000 to less than 50 Bq kg{sup -1}, in decreasing order: {sup 137}Cs, {sup 40}K, {sup 90}Sr, {sup 210}Pb,{sup 226}Ra, {sup 232}Th, {sup 134}Cs, {sup 235}U. In bott radionuclide contents decreased in the same order as in fly ash, but were smaller, and {sup 210}Pb was hardly detectable. The NH{sub 4}Ac extractable fractions of activities for isotopes of alkaline elements (K, Cs) in bottom ash were lower than in fly ash, whereas solubility of heavier isotopes was low. Safety requirements defined by STUK in ST-guide 12.2 for handling of peat ash were fulfilled at each of the sites. Use of ash for land-filling and construction of streets was minimal during the sampling period. Increasing this type of ash use had often needed further investigations, as description of the use of additional materials that attenuate radiation. Fertilisation of forests with wood ash adds slightly to the external irradiation in forests, but will mostly decrease doses received through use of timber, berries, mushrooms and game meat. (orig.)

  16. An improved ashing procedure for biologic sample

    Energy Technology Data Exchange (ETDEWEB)

    Zongmei, Wu [Zhejiang Province Enviromental Radiation Monitoring Centre (China)

    1992-07-01

    The classical ashing procedure in muffle was modified for biologic samples. In the modified procedure the door of muffle was open in the duration of ashing process, the ashing was accelerated and the ashing product quality was comparable to that the classical procedure. The modified procedure is suitable for ashing biologic samples in large batches.

  17. An improved ashing procedure for biologic sample

    International Nuclear Information System (INIS)

    Wu Zongmei

    1992-01-01

    The classical ashing procedure in muffle was modified for biologic samples. In the modified procedure the door of muffle was open in the duration of ashing process, the ashing was accelerated and the ashing product quality was comparable to that the classical procedure. The modified procedure is suitable for ashing biologic samples in large batches

  18. Treatment of fly ash for use in concrete

    Science.gov (United States)

    Boxley, Chett [Park City, UT

    2012-05-15

    A process for treating fly ash to render it highly usable as a concrete additive. A quantity of fly ash is obtained that contains carbon and which is considered unusable fly ash for concrete based upon foam index testing. The fly ash is mixed with a quantity of spray dryer ash (SDA) and water to initiate a geopolymerization reaction and form a geopolymerized fly ash. The geopolymerized fly ash is granulated. The geopolymerized fly ash is considered usable fly ash for concrete according to foam index testing. The geopolymerized fly ash may have a foam index less than 40%, and in some cases less than 20%, of the foam index of the untreated fly ash. An optional alkaline activator may be mixed with the fly ash and SDA to facilitate the geopolymerization reaction. The alkaline activator may contain an alkali metal hydroxide, carbonate, silicate, aluminate, or mixtures thereof.

  19. Observed salinity changes in the Alappuzha mud bank, southwest coast of India and its implication to hypothesis of mudbank formation

    Science.gov (United States)

    Muraleedharan, K. R.; Dinesh Kumar, P. K.; Prasanna Kumar, S.; Srijith, B.; John, Sebin; Naveen Kumar, K. R.

    2017-04-01

    Alappuzha mud bank draws special attention among the twenty-mud bank locations reported along the Kerala coast by its remoteness from riverine sources. Among several hypotheses proposed for the formation of mud bank, the subterranean hypothesis was most accepted because of the occurrence of low salinity in the bottom layers. The present study provides evidence to show that occurrence of low salinity waters near the bottom in the mud bank region is an artifact of measuring technique employed for the measurement of salinity. The usual technique of conductivity based salinity determination completely fails in the presence of water laden with high amount of suspended sediment. Laboratory experiments were conducted to determine the response of electrode and conductivity cell sensor types to determine the salinity using a range of suspended sediment in the water column. Actual sediment samples from the mud bank region were utilized for the above studies. Based on field observations and experiments, we conclude that the low salinity was the manifestation of the presence highly turbid fluid mud formation in the mud bank region rather than the influence of fresh water.

  20. Engineering properties of fly ash concrete

    International Nuclear Information System (INIS)

    Hilmi Mahmud

    1999-01-01

    This paper presents some of the engineering properties of Malaysian fly ash concrete. Workability, compressive, flexural, tensile splitting, drying shrinkage, elastic modulus and non destructive tests were performed on fly ash and control OPC concrete specimens. Data show that concrete containing 25% fly ash replacement of cement exhibit superior or similar engineering properties to that normal concrete without fly ash. These encouraging results demonstrated the technical merits of incorporating fly ash in concrete and should pave the way for wide scale use of this versatile material in the Malaysian construction industry. (author)

  1. Novel Desorber for Online Drilling Mud Gas Logging

    Directory of Open Access Journals (Sweden)

    Marcin Lackowski

    2016-01-01

    Full Text Available This work presents the construction solution and experimental results of a novel desorber for online drilling mud gas logging. The traditional desorbers use mechanical mixing of the liquid to stimulate transfer of hydrocarbons to the gaseous phase that is further analyzed. The presented approach is based on transfer of hydrocarbons from the liquid to the gas bubbles flowing through it and further gas analysis. The desorber was checked for gas logging from four different drilling muds collected from Polish boreholes. The results of optimization studies are also presented in this study. The comparison of the novel desorber with a commercial one reveals strong advantages of the novel one. It is characterized by much better hydrocarbons recovery efficiency and allows reaching lower limits of detection of the whole analytical system. The presented desorber seems to be very attractive alternative over widely used mechanical desorbers.

  2. Treatment of fly ash for use in concrete

    Science.gov (United States)

    Boxley, Chett; Akash, Akash; Zhao, Qiang

    2013-01-08

    A process for treating fly ash to render it highly usable as a concrete additive. A quantity of fly ash is obtained that contains carbon and which is considered unusable fly ash for concrete based upon foam index testing. The fly ash is mixed with an activator solution sufficient to initiate a geopolymerization reaction and for a geopolymerized fly ash. The geopolymerized fly ash is granulated. The geopolymerized fly ash is considered usable fly ash for concrete according to foam index testing. The geopolymerized fly ash may have a foam index less than 35% of the foam index of the untreated fly ash, and in some cases less than 10% of the foam index of the untreated fly ash. The activator solution may contain an alkali metal hydroxide, carbonate, silicate, aluminate, or mixtures thereof.

  3. Large-Scale Consumption and Zero-Waste Recycling Method of Red Mud in Steel Making Process

    Directory of Open Access Journals (Sweden)

    Guoshan Ning

    2018-03-01

    Full Text Available To release the environmental pressure from the massive discharge of bauxite residue (red mud, a novel recycling method of red mud in steel making process was investigated through high-temperature experiments and thermodynamic analysis. The results showed that after the reduction roasting of the carbon-bearing red mud pellets at 1100–1200 °C for 12–20 min, the metallic pellets were obtained with the metallization ratio of ≥88%. Then, the separation of slag and iron achieved from the metallic pellets at 1550 °C, after composition adjustment targeting the primary crystal region of the 12CaO·7Al2O3 phase. After iron removal and composition adjustment, the smelting-separation slag had good smelting performance and desulfurization capability, which meets the demand of sulfurization flux in steel making process. The pig iron quality meets the requirements of the high-quality raw material for steel making. In virtue of the huge scale and output of steel industry, the large-scale consumption and zero-waste recycling method of red mud was proposed, which comprised of the carbon-bearing red mud pellets roasting in the rotary hearth furnace and smelting separation in the electric arc furnace after composition adjustment.

  4. Gasification of high ash, high ash fusion temperature bituminous coals

    Science.gov (United States)

    Liu, Guohai; Vimalchand, Pannalal; Peng, WanWang

    2015-11-13

    This invention relates to gasification of high ash bituminous coals that have high ash fusion temperatures. The ash content can be in 15 to 45 weight percent range and ash fusion temperatures can be in 1150.degree. C. to 1500.degree. C. range as well as in excess of 1500.degree. C. In a preferred embodiment, such coals are dealt with a two stage gasification process--a relatively low temperature primary gasification step in a circulating fluidized bed transport gasifier followed by a high temperature partial oxidation step of residual char carbon and small quantities of tar. The system to process such coals further includes an internally circulating fluidized bed to effectively cool the high temperature syngas with the aid of an inert media and without the syngas contacting the heat transfer surfaces. A cyclone downstream of the syngas cooler, operating at relatively low temperatures, effectively reduces loading to a dust filtration unit. Nearly dust- and tar-free syngas for chemicals production or power generation and with over 90%, and preferably over about 98%, overall carbon conversion can be achieved with the preferred process, apparatus and methods outlined in this invention.

  5. Serpentinite mud volcanism: observations, processes, and implications.

    Science.gov (United States)

    Fryer, Patricia

    2012-01-01

    Large serpentinite mud volcanoes form on the overriding plate of the Mariana subduction zone. Fluids from the descending plate hydrate (serpentinize) the forearc mantle and enable serpentinite muds to rise along faults to the seafloor. The seamounts are direct windows into subduction processes at depths far too deep to be accessed by any known technology. Fluid compositions vary with distance from the trench, signaling changes in chemical reactions as temperature and pressure increase. The parageneses of rocks in the mudflows permits us to constrain the physical conditions of the decollement region. If eruptive episodes are related to seismicity, seafloor observatories at these seamounts hold the potential to capture a subduction event and trace the effects of eruption on the biological communities that the slab fluids support, such as extremophile Archaea. The microorganisms that inhabit this high-pH, extreme environment support their growth by utilizing chemical constituents present in the slab fluids. Some researchers now contend that the serpentinization process itself may hold the key to the origin of life on Earth.

  6. Can mud (silt and clay) concentration be used to predict soil organic carbon content within seagrass ecosystems?

    KAUST Repository

    Serrano, Oscar

    2016-09-07

    The emerging field of blue carbon science is seeking cost-effective ways to estimate the organic carbon content of soils that are bound by coastal vegetated ecosystems. Organic carbon (C-org) content in terrestrial soils and marine sediments has been correlated with mud content (i.e., silt and clay, particle sizes <63 mu m), however, empirical tests of this theory are lacking for coastal vegetated ecosystems. Here, we compiled data (n = 1345) on the relationship between C-org and mud contents in seagrass ecosystems (79 cores) and adjacent bare sediments (21 cores) to address whether mud can be used to predict soil C-org content. We also combined these data with the delta C-13 signatures of the soil C-org to understand the sources of Corg stores. The results showed that mud is positively correlated with soil C-org content only when the contribution of seagrass-derived C-org to the sedimentary C-org pool is relatively low, such as in small and fast-growing meadows of the genera Zostera, Halodule and Halophila, and in bare sediments adjacent to seagrass ecosystems. In large and long-living seagrass meadows of the genera Posidonia and Amphibolis there was a lack of, or poor relationship between mud and soil C-org content, related to a higher contribution of seagrass-derived C-org to the sedimentary C-org pool in these meadows. The relatively high soil C-org contents with relatively low mud contents (e.g., mud-C-org saturation) in bare sediments and Zostera, Halodule and Halophila meadows was related to significant allochthonous inputs of terrestrial organic matter, while higher contribution of seagrass detritus in Amphibolis and Posidonia meadows disrupted the correlation expected between soil C-org and mud contents. This study shows that mud is not a universal proxy for blue carbon content in seagrass ecosystems, and therefore should not be applied generally across all seagrass habitats. Mud content can only be used as a proxy to estimate soil C-org content for

  7. Geochemistry and microbiology at gas hydrate and mud volcano sites in the black sea

    Science.gov (United States)

    Drews, M.; Schmaljohann, R.; Wallmann, K.

    2003-04-01

    We present geochemical and microbiological results which were obtained from sediments at gas hydrate and mud volcano sites in the Sorokin Trough (northern Black Sea, south east of the Crimean peninsula) at water depths of about 1800 to 2100 m during the METEOR cruise 52-1. The surface near sub-bottom accumulations of gas hydrates (occuring at depths of several meters or less beneath the sea floor) in the Black Sea are associated with numerous mud volcanos. At stations we investigated gas hydrates occurred below 10 cm to 100 cm with a significant influence on the sediment biochemistry. Analyses revealed high methane concentrations, anoxic and sulfidic conditions, a steep sulfate gradient, carbonate precipitation, and high anaerobic methane oxidation rates. In proximity of the so called Odessa mud volcano one investigated sampling station showed maximum methane oxidation rates in the depth horizon of a firm 2 cm thick carbonate crust layer, adhered to by a bacterial mat. This observation is taken to indicate that the bacteria are causing or mediating the crust formation by their anaerobic methane oxidation metabolism. The station was further characterised by two layers of gas hydrate fragments and lenses below 1 m depth. A 2 to 4 cm thick carbonate crust with attached bacterial mat from a Yalta mud vulcano sample (2124 m water depth) was investigated under the scanning electron microscope. The stiff gelatinous mat showed a dense and morphologically uniform population of rod shaped bacteria with only a few nests of coccoid cells. Purified mat material exhibited anaerobic methane oxidation activity. These mats resemble the type previously found in the shallow NW methane seep area of the Black Sea, where it covers carbonate chimneys. Samples from two sites atop the summit of the active but flat-topped Dvurechenskii mud volcano were characterised by very high methane oxidation rates (up to 563 nmol/cm3/d) at the sediment surface. Strong pore water gradients of chloride

  8. Determining the ash content of coal flotation tailings using an MPOF optical ash meter

    Energy Technology Data Exchange (ETDEWEB)

    Sikora, T; Sliwa, J

    1982-01-01

    The block layout, a description of the design and principles of operation of an automatic optical, continuous action MPOF type ash meter are presented. The difference in the optical properties of coal and rock is used in the ash meter. The identification of the ash content is conducted on the basis of the spectral characteristics of reflection of a finely dispersed aqueous coal and rock suspension.

  9. THE PROPOSED ALUMINA INDUSTRY AND HOW TO MITIGATE AGAINST THE RED MUD FOOTPRINT IN GHANA

    Directory of Open Access Journals (Sweden)

    S. K. Y. Gawu

    2012-01-01

    Full Text Available Bauxite tailings, also known as red mud, are often generated in vast quantities by extracting alumina from bauxites. The relatively complex composition of the red mud, an insoluble residue from bauxite processing, coupled with its fine particle size distribution, high pH, poor settling properties and some toxic rare metal associations, make its disposal problematic. Two locations are being considered for the sitting of a bauxite refinery in Ghana. Since large quantities of tailings is expected to be produced at a selected site efforts need to be geared towards its management to ensure that the red mud footprint is not repeated in Ghana as happened elsewhere. This paper considers the two proposed sites and applies a site ranking criteria to identify the most suitable site, as well as an environmentally suitable disposal technology based on the selected site conditions and the general red mud characteristics. This study could serve as a sustainable development approach in site selection and the choice of disposal technologies.

  10. Mud cloth from Mali: its making and use

    African Journals Online (AJOL)

    Owner

    book covers and wrapping paper. ... used in mud cloth can be traced back to the 12th cen- tury AD ... cluded a bogolan wrap in his winter collection (Adire .... Stencils made from cardboard or plastic are also used. These stencilled cloths can be ...

  11. Limitations of microbial hydrocarbon degradation at the Amon mud volcano (Nile deep-sea fan

    Directory of Open Access Journals (Sweden)

    J. Felden

    2013-05-01

    Full Text Available The Amon mud volcano (MV, located at 1250 m water depth on the Nile deep-sea fan, is known for its active emission of methane and non-methane hydrocarbons into the hydrosphere. Previous investigations showed a low efficiency of hydrocarbon-degrading anaerobic microbial communities inhabiting the Amon MV center in the presence of sulfate and hydrocarbons in the seeping subsurface fluids. By comparing spatial and temporal patterns of in situ biogeochemical fluxes, temperature gradients, pore water composition, and microbial activities over 3 yr, we investigated why the activity of anaerobic hydrocarbon degraders can be low despite high energy supplies. We found that the central dome of the Amon MV, as well as a lateral mud flow at its base, showed signs of recent exposure of hot subsurface muds lacking active hydrocarbon degrading communities. In these highly disturbed areas, anaerobic degradation of methane was less than 2% of the methane flux. Rather high oxygen consumption rates compared to low sulfide production suggest a faster development of more rapidly growing aerobic hydrocarbon degraders in highly disturbed areas. In contrast, the more stabilized muds surrounding the central gas and fluid conduits hosted active anaerobic hydrocarbon-degrading microbial communities. The low microbial activity in the hydrocarbon-vented areas of Amon MV is thus a consequence of kinetic limitations by heat and mud expulsion, whereas most of the outer MV area is limited by hydrocarbon transport.

  12. Sequential activities of Dynein, Mud and Asp in centrosome-spindle coupling maintain centrosome number upon mitosis.

    Science.gov (United States)

    Bosveld, Floris; Ainslie, Anna; Bellaïche, Yohanns

    2017-10-15

    Centrosomes nucleate microtubules and are tightly coupled to the bipolar spindle to ensure genome integrity, cell division orientation and centrosome segregation. While the mechanisms of centrosome-dependent microtubule nucleation and bipolar spindle assembly have been the focus of numerous works, less is known about the mechanisms ensuring the centrosome-spindle coupling. The conserved NuMA protein (Mud in Drosophila ) is best known for its role in spindle orientation. Here, we analyzed the role of Mud and two of its interactors, Asp and Dynein, in the regulation of centrosome numbers in Drosophila epithelial cells. We found that Dynein and Mud mainly initiate centrosome-spindle coupling prior to nuclear envelope breakdown (NEB) by promoting correct centrosome positioning or separation, while Asp acts largely independently of Dynein and Mud to maintain centrosome-spindle coupling. Failure in the centrosome-spindle coupling leads to mis-segregation of the two centrosomes into one daughter cell, resulting in cells with supernumerary centrosomes during subsequent divisions. Altogether, we propose that Dynein, Mud and Asp operate sequentially during the cell cycle to ensure efficient centrosome-spindle coupling in mitosis, thereby preventing centrosome mis-segregation to maintain centrosome number. © 2017. Published by The Company of Biologists Ltd.

  13. Electrodialytic removal of heavy metals from fly ashes

    DEFF Research Database (Denmark)

    Pedersen, Anne Juul

    2002-01-01

    The aim of the Ph.D. work was to develop the electrodialytic remediation method for removal of heavy metals from fly ashes. The work was focused on two types of fly ashes: fly ashes from wood combustion and fly ashes from municipal solid waste incineration.......The aim of the Ph.D. work was to develop the electrodialytic remediation method for removal of heavy metals from fly ashes. The work was focused on two types of fly ashes: fly ashes from wood combustion and fly ashes from municipal solid waste incineration....

  14. Evidence of methane venting and geochemistry of brines on mud volcanoes of the eastern Mediterranean

    NARCIS (Netherlands)

    Charlou, J.-L.; Donval, J.-P.; Zitter, T.; Roy, N.; Jean Baptiste, P.; Foucher, J.P.; Woodside, J.M.; Medinaut, Party

    2003-01-01

    As a part of the Dutch-French MEDINAUT diving expedition in 1998, cold seeps and mud volcanoes were studied and sampled in two distinctive tectonic settings in the eastern Mediterranean Sea. The first setting was the Olimpi Mud Volcano field (OMV area), including Napoli, Milano, Maidstone and Moscow

  15. Utilization options for fly ash, bottom ash, and slag in Eastern Europe

    Energy Technology Data Exchange (ETDEWEB)

    Manz, O.E.

    1995-12-01

    Since 1967, at least six ash utilization symposiums have been held in the United States, with papers presented by several European authors on the utilization of coal by-products in Eastern Europe. There is currently over 80,000 megawatts of installed coal-fired capacity available in that region. Unfortunately, of the 117,778,000 tonnes of fly ash, bottom ash, and slag produced in Eastern Europe in 1989, only 13% was utilized. This paper outlines the research and levels and kinds of coal by-product utilization taking place in Eastern Europe since the late 1960s.

  16. Ash fusion temperatures and the transformations of coal ash particles to slag

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, S.; Wall, T.F.; Creelman, R.A.; Gupta, R. [Univ. of Newcastle, Callaghan (Australia)

    1996-12-31

    A mechanistic study is detailed in which coal ash is heated with its shrinkage measured continuously up to a temperature of 1600{degrees}C. The temperatures corresponding to the rapid rate of shrinkage are shown to correspond to the formation of eutectics identified on phase diagrams. Samples were therefore heated to these temperatures, cooled rapidly and examined with an SEM to identify the associated chemical and physical changes. The progressive changes in the range of chemical analysis (from SEM), the extent of undissolved ash particles and porosity were then quantified and related to homogenization, viscosity and ash fusion mechanisms.

  17. Ash fusion temperatures and the transformations of coal ash particles to slag

    Energy Technology Data Exchange (ETDEWEB)

    Wall, T.F.; Creelman, R.A.; Gupta, R.; Gupta, S. [Univ. of Newcastle (Australia)

    1996-10-01

    A mechanistic study is detailed in which coal ash is heated with the shrinkage and electrical resistance measured continuously up to a temperature of 1600{degrees}C. The temperatures corresponding to rapid rates of shrinkage are shown to correspond to the formation of eutectics identified on phase diagrams. Samples where therefore heated to these temperatures, cooled rapidly and examined with an SEM to identify the associated chemical and physical changes. The progressive changes in the range of chemical analysis (from SEM), the extent of undissolved ash particles and porosity are then quantified and related to the shrinkage events and standard ash fusion temperatures.

  18. Diplomacy Through Earth Sciences: An Overview of US Geological Survey Technical Assistance Regarding the Ongoing LUSI Mud Eruption, East Java, Indonesia

    Science.gov (United States)

    Casadevall, T. J.

    2009-12-01

    In June 2007, the US Department of State (DOS) requested assistance from the USGS to provide technical guidance and advice to the US Mission in Indonesia regarding the Lumpur Sidoarjo (LUSI) mud crisis. In May 2006, LUSI began as a mud eruption from a series of mud springs adjacent to an oil and gas exploration well being drilled near Surabaya, East Java, Indonesia. The production of mud and waters from the LUSI crater area has now continued for more than 3 years with no significant change in mud production rate (~110,000 cubic meters per day) nor in temperature of the mud (70-80 degrees C). Engineers suggest that mud production will continue at these rates for years to decades to come. Regardless of future activity at LUSI, the current mud accumulation of more than 100 million cubic meters poses a physical and environmental hazard which requires continuous monitoring and observation. The first response to the 2007 DOS request involved a site visit to Indonesia in September 2007. The result of that visit was to recommend to the Government of Indonesia (GOI) that they focus on long-term management of the mud rather than focus on the controversy as to the cause of the eruption or the debate about stopping the flow. Other recommendations from the initial 2007 technical visit included contracting for a US scientist to be co-located with engineers of the Sidoarjo Mud Management Board (BPLS) in Surabaya, East Java, to advise and consult on day-to-day developments at the site of the mud eruption. A second technical team visit by USGS scientists and an engineer from the US Army Corps of Engineers in October-November 2008 made additional recommendations on the long-term management of the mud and was followed in December by the start of a 6 month contract for the US mud adviser. From the start of activity in mid-2006 through late-2008, there was a clear sense of urgency at the US Mission in Indonesia to provide guidance and advice and included the personal intervention of

  19. A comprehensive sediment dynamics study of a major mud belt system on the inner shelf along an energetic coast.

    Science.gov (United States)

    Liu, James T; Hsu, Ray T; Yang, Rick J; Wang, Ya Ping; Wu, Hui; Du, Xiaoqin; Li, Anchun; Chien, Steven C; Lee, Jay; Yang, Shouye; Zhu, Jianrong; Su, Chih-Chieh; Chang, Yi; Huh, Chih-An

    2018-03-09

    Globally mud areas on continental shelves are conduits for the dispersal of fluvial-sourced sediment. We address fundamental issues in sediment dynamics focusing on how mud is retained on the seabed on shallow inner shelves and what are the sources of mud. Through a process-based comprehensive study that integrates dynamics, provenance, and sedimentology, here we show that the key mechanism to keep mud on the seabed is the water-column stratification that forms a dynamic barrier in the vertical that restricts the upward mixing of suspended sediment. We studied the 1000 km-long mud belt that extends from the mouth of the Changjiang (Yangtze) River along the coast of Zhejiang and Fujian Provinces of China and ends on the west coast of Taiwan. This mud belt system is dynamically attached to the fluvial sources, of which the Changjiang River is the primary source. Winter is the constructive phase when active deposition takes place of fine-grained sediment carried mainly by the Changjiang plume driven by Zhe-Min Coastal Currents southwestward along the coast.

  20. Hazards Associated With Recent Popocatepetl Ash Emissions

    Science.gov (United States)

    Nieto, A.; Martin, A.; Espinasa-Pereña, R.; Ferres, D.

    2013-05-01

    Popocatepetl has been producing ash from small eruptions since 1994. Until 2012 about 650 small ash emissions have been recorded at the monitoring system of Popocatépetl Volcano. Ash consists mainly of glassy lithic clasts from the recent crater domes, plagioclase and pyroxene crystals, and in major eruptions, olivine and/or hornblende. Dome forming eruptions produced a fine white ash which covers the coarser ash. This fine ash consists of plagioclase, glass and cristobalite particles mostly under15 microns. During the recent crisis at Popocatépetl, April and May2012 ash fell on villages to the east and west of the volcano, reaching Mexico City (more than 20 million people) and Puebla (2 million people). In 14 cases the plumes had heights over 2 km, the largest on May 2 and 11 (3 and 4 km in height, respectively). Heavier ash fall occurred on April 13, 14, 20, and 23 and May 2, 3, 5, 11, 14, 23, 24 and 25. A database for ash fall was constructed from April 13 with field observations, reports emitted by the Centro Nacional de Comunicaciones (CENACOM), ash fall advisories received at CENAPRED and alerts from the Servicios a la Navegación en el Espacio Aéreo Mexicano (SENEAM). This aim of this database is to calculate areas affected by the ash and estimate the ash fall volume emitted by Popocatépetl in each of these events. Heavy ash fall from the May 8 to May 11 combined with reduced visibility due to fog forced to closure of the Puebla airport during various periods of time, for up to 13 hours. Domestic and international flights were cancelled. Ash eruptions have caused respiratory conditions in the state of Puebla, to the east of the volcano, since 1994 (Rojas et al, 2001), but because of the changing wind conditions in the summer mainly, some of these ash plumes go westward to towns in the State of Mexico and even Mexico City. Preliminary analyses of these eruptions indicate that some ash emissions produced increased respiratory noninfectious problems

  1. Analysis list: ash2 [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available ash2 Larvae + dm3 http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/target/ash2.1.tsv ...http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/target/ash2.5.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/target/ash2....10.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/colo/ash2.Larvae.tsv http://dbarchive.biosciencedbc.jp/kyushu-u/dm3/colo/Larvae.gml ...

  2. Attraction of the emerald ash borer to ash trees stressed by girdling, herbicide treatment, or wounding

    Science.gov (United States)

    Deborah McCullough; Therese Poland; David. Cappaert

    2009-01-01

    New infestations of emerald ash borer, Agrilus planipennis Fairmaire, an invasive pest native to Asia, are difficult to detect until densities build and symptoms appear on affected ash (Fraxinus spp). We compared the attraction of A. planipennis to ash trees stressed by girdling (bark and phloem removed...

  3. Ash in fire affected ecosystems

    Science.gov (United States)

    Pereira, Paulo; Jordan, Antonio; Cerda, Artemi; Martin, Deborah

    2015-04-01

    Ash in fire affected ecosystems Ash lefts an important footprint in the ecosystems and has a key role in the immediate period after the fire (Bodi et al., 2014; Pereira et al., 2015). It is an important source of nutrients for plant recover (Pereira et al., 2014a), protects soil from erosion and controls soil hydrological process as runoff, infiltration and water repellency (Cerda and Doerr, 2008; Bodi et al., 2012, Pereira et al., 2014b). Despite the recognition of ash impact and contribution to ecosystems recuperation, it is assumed that we still have little knowledge about the implications of ash in fire affected areas. Regarding this situation we wanted to improve our knowledge in this field and understand the state of the research about fire ash around world. The special issue about "The role of ash in fire affected ecosystems" currently in publication in CATENA born from the necessity of joint efforts, identify research gaps, and discuss future cooperation in this interdisciplinary field. This is the first special issue about fire ash in the international literature. In total it will be published 10 papers focused in different aspects of the impacts of ash in fire affected ecosystems from several parts of the world: • Fire reconstruction using charcoal particles (Burjachs and Espositio, in press) • Ash slurries impact on rheological properties of Runoff (Burns and Gabet, in press) • Methods to analyse ash conductivity and sorbtivity in the laboratory and in the field (Balfour et al., in press) • Termogravimetric and hydrological properties of ash (Dlapa et al. in press) • Effects of ash cover in water infiltration (Leon et al., in press) • Impact of ash in volcanic soils (Dorta Almenar et al., in press; Escuday et al., in press) • Ash PAH and Chemical extracts (Silva et al., in press) • Microbiology (Barreiro et al., in press; Lombao et al., in press) We believe that this special issue will contribute importantly to the better understanding of

  4. Formation and utilization of fly ash

    Energy Technology Data Exchange (ETDEWEB)

    Vargyai, J

    1974-01-01

    General problems of slag and fly ash formation and utilization are discussed. The ever-increasing energy demand, and the comeback of coal as an energy carrier in power plants call for efficient solutions to the problem of slag and fly ash. Slag and fly ash are used for concrete in which they partly replace cement. Other possible uses are the amelioration of acid soils, fireclay manufacture, road construction, and tiles. It is possible to recover metals, such as vanadium, iron, aluminum, and radioactive materials from certain types of fly ash and slag. The utilization of fly ash is essential also with respect to the abatement of entrainment from dumps.

  5. The influence of using volcanic ash and lime ash as filler on compressive strength in self compacting concrete

    Science.gov (United States)

    Karolina, Rahmi; Panatap Simanjuntak, Murydrischy

    2018-03-01

    Self Compacting Concrete (SCC) is a technology which is developing today in which concrete solidifies by itself without using vibrator. Casting conventional concrete which has a lot of reinforcement bars sometimes finds difficulty in achieving optimal solidity. The method used to solve this problem is by using SCC technology. SCC was made by using filler, volcanic ash, and lime ash as the filling materials so that the concrete became more solid and hollow space could be filled up. The variation of using these two materials was 10%, 15%, 20%, and 25% of the cementitious mass and using 1% of superplasticizer from cementitious material. The supporting testing was done by using the test when the concrete was still fluid and when it was solid. Malleable concrete was tested by using EFNARC 2002 standard in slump flow test, v-funnel test, l-shaped box test, and j-ring test to obtain filling ability and passing ability. In this malleable lime concrete test, there was the decrease, compared with normal SCC concrete without adding volcanic ash and lime ash. Testing was also done in solid concrete in compressive strength, tensile strength, and concrete absorption. The result of the testing showed that the optimum tensile strength in Variation 1, without volcanic ash and lime ash – with 1% of superplasticizer was 39.556 MPa, the optimum tensile strength in Variation 1, without volcanic ash and lime ash- with 1% of super-plasticizer was 3.563 MPa, while the value of optimum absorption which occurred in Variation 5 (25% of volcanic ash + 25% of lime ash + 50% of cement + 1% of superplasticizer) was 1.313%. This was caused by the addition of volcanic ash and lime ash which had high water absorption.

  6. Wildfire Ash: Chemical Composition, Ash-Soil Interactions and Environmental Impacts

    Science.gov (United States)

    Brook, Anna; Hamzi, Seham; Wittenberg, Lea

    2015-04-01

    Of the five classical factors of soil formation, climate, parent material, topography, time, organisms, and recently recognized human activity, it is the latter factor which discretely includes fire and post-burn impact. However, it is considered that soil undergoing fire just experience a temporary removal of the top organic horizon, thus slightly modified and often labeled as 'temporarily disturbed' soil or soil 'under restoration/rehabilitation'. In fact the suggested seventh factor, post-burned produced ash, can act both dependently and independently of the other soil forming factors (Levin et al., 2013; Certini 2013). They are interdependent in cases where ash influences occur on time scales similar to 'natural' soil formation (Keesstra et ai., 2014) such as changes in vegetation. On the other hand, in post-fire areas a strong dependency is expected between soil-water retention mechanism, climate and topography. Wild-land fires exert many changes on the physical, chemical, mineralogical, biological, and morphological properties of soil that, in turn, affect the soil's hydrology and nutrient flux, modifying its ability to support vegetation and resist erosion. The ash produced by forest fires is a complex mixture composed of organic and inorganic particles characterized by vary physical-chemical and morphological properties. The importance of this study is straightforwardly related to the frequency and large-scales wildfires in Mediterranean region. In fact, wildfires are major environmental and land management concern in the world, where the number and severity of wildfires has increased during the past decades (Bodi, 2013). Certini (2013) assumed that cumulatively all of the vegetated land is burned in about 31 years annually affecting 330-430 Mha (over 3% of the Earth's surface) and wide range of land cover types worldwide including forests, peatlands, shrublands and grasslands. Whereas, the fire is identified as an important factor in soil formation, the

  7. [Situation and assessment of heavy metal pollution in river and mud in one city in Henan Province].

    Science.gov (United States)

    Xi, Jingzhuan; Li, Cuimei; Wang, Shouying; Jiang, Zhigang; Zhang, Miaomiao; Han, Guangliang

    2010-11-01

    To study the heavy metal contamination status in river water and mud in the suburb of a city in Henan Province. Typical sampling method is used to select a farmland irrigation river of the suburb of a city. Use the atomic absorption spectrophotometry, and measure the heavy metal cadmium (Cd), copper (Cu), lead (Pb) in the river water samples and mud samples by graphite furnace method and flame method, respectively. The results of water were compared with GB 3838-2002, Environmental Quality Standards for Surface Water, and GB 5084-2005, Standards for Irrigation Water Quality. The results of mud were compared with national soil background value. The contents of Cu and Cd in the river samples do not exceed the standard, and that of Pb is 3 to 6 times higher than the standard. According to the single factor pollution index method, the single factor pollution indice of Cu, and Cd in the river are less than 0.2 and are of clean level, while that of Pb reaches 6.84, indicating the Pb pollution in river water is severe. Cu in mud is more than 4 times of the soil background value, and that of Cd is more than 69 times of the soil background value, and that of Pb is more than 2 times of the soil background value. The single item pollution index indicates, in mud, the pollution index of Pb is 2.5, medium level pollution. The pollution indice of Cu and Cd in mud are more than 3, is severe pollution, and the Cd pollution is especially heavy, and the single pollution index reaches 67.76. The comprehensive pollution indice of the river and the mud are 5.346 and 84.115, respectively, indicating that both are at heavy pollution level. The main pollution source of the river originates from Pb, and that of the mud is from Cd and it is required to take measure and control as early as possible.

  8. Associative properties of 137Cs in biofuel ashes

    International Nuclear Information System (INIS)

    Ravila, A.; Holm, E.

    1999-01-01

    The present study aims to reveal how radiocesium is associated to the ash particles derived from biofuel combustion. A sequential extraction procedure was carried out for the characterisation of radiocesium speciation in ash generated by different fuels and burner types. The ash types considered were fly ash and bottom ash collected from Swedish district heating plants using bark wood or peat as fuel. A fraction of the radiocesium in biofuel ash can easily become solubilised and mobilised by water and also, a significant fraction of the radionuclides can be bound to the ash particles in cation-exchangeable forms. Therefore, at using the ash derived from biofuels to recycle mineral nutrients for forestry or short rotation coppicing, radiocesium solubilised and leached from the ash by rains has a potential to rather quickly enter the rooting zone of forest vegetation or energy crops. On the other hand, radiocesium strongly bound to the ash will migrate slowly into the soil column with the successive accumulation of litter and in the process act to maintain the external dose rate at an elevated level for a long time. The results of the sequential extraction procedure and activity determination of the different extracted fractions implies that the bioavailable fraction of radiocesium in ash from bark, wood or peat is in the range between 20-85% of the total ash contents. Peat ash collected from a powder burner strongly retained a large fraction (70-90%) of its radiocesium content while the peat ash from a continuos fluidized bed type burner retained nearly 100% of the radiocesium in the bottom ash and only about 15% in the fly ash

  9. Indirect effects of emerald ash borer-induced ash mortality and canopy gap formation on epigaeic beetles.

    Science.gov (United States)

    Gandhi, Kamal J K; Smith, Annemarie; Hartzler, Diane M; Herms, Daniel A

    2014-06-01

    Exotic herbivorous insects have drastically and irreversibly altered forest structure and composition of North American forests. For example, emerald ash borer (Agrilus planipennis Fairmaire) from Asia has caused wide-scale mortality of ash trees (Fraxinus spp.) in eastern United States and Canada. We studied the effects of forest changes resulting from emerald ash borer invasion on epigaeic or ground beetles (Coleoptera: Carabidae) along a gradient of ash dieback and gap sizes in southeastern Michigan. Ground beetles were sampled in hydric, mesic, and xeric habitats in which black (Fraxinus nigra Marshall), green (Fraxinus pennsylvanica Marshall), and white (Fraxinus americana L.) ash were the most common species, respectively. During 2006-2007, we trapped 2,545 adult ground beetles comprising 52 species. There was a negative correlation between percent ash tree mortality in 2006 and catches of all beetles. Catches of Agonum melanarium Dejean (in 2006) and Pterostichus mutus (Say) (in 2006-2007) were negatively correlated with tree mortality and gap size, respectively. However, catches of Pterostichus corvinus Dejean were positively correlated with gap size in 2006. As ash mortality and average gap size increased from 2006 to 2007, catches of all beetles as well as P. mutus and Pterostichus stygicus (Say) increased (1.3-3.9 times), while species diversity decreased, especially in mesic and xeric stands. Cluster analysis revealed that beetle assemblages in hydric and mesic stand diverged (25 and 40%, respectively) in their composition from 2006 to 2007, and that hydric stands had the most unique beetle assemblages. Overall, epigaeic beetle assemblages were altered in ash stands impacted by emerald ash borer; however, these impacts may dissipate as canopy gaps close.

  10. Review of ecosystem level impacts of emerald ash borer on black ash wetlands: What does the future hold?

    Science.gov (United States)

    Randall K. Kolka; Anthony W. D' Amato; Joseph W. Wagenbrenner; Robert A. Slesak; Thomas G. Pypker; Melissa B. Youngquist; Alexis R. Grinde; Brian J. Palik

    2018-01-01

    The emerald ash borer (EAB) is rapidly spreading throughout eastern North America and devastating ecosystems where ash is a component tree. This rapid and sustained loss of ash trees has already resulted in ecological impacts on both terrestrial and aquatic ecosystems and is projected to be even more severe as EAB invades black ash-dominated wetlands of the western...

  11. Evaluation of New Fluid Mud Survey System at Field Sites

    National Research Council Canada - National Science Library

    Engler

    1992-01-01

    This technical note presents an intermediate evaluation of a fluid mud survey system with respect to operability, practicability, and repeatability based on field tests conducted at Calcasieu River, Louisiana...

  12. Radiocarbon and cation-radio ages for rock varnish on Tioga and Tahoe marainal boulders of Pine Creek, eastern Sierra Nevada, California, and their paleoclimatic implications

    Science.gov (United States)

    Dorn, R.I.; Turrin, B.D.; Jull, A.J.T.; Linick, T.W.; Donahue, D.J.

    1987-01-01

    Accelerator mass spectrometry 14C analyses of organic matter extracted from rock varnishes on morainal boulders yield limiting minimum ages for three crests of the Tioga glaciation. At Pine Creek in the eastern Sierra Nevada, varnish started to form on boulders of the outermost Tioga moraine before 19,000 yr B.P., and varnish originated on the innermost Tioga moraine before 13,200 yr B.P. Comparisons with lake-level, paleohydrological, paleoecological, colluvial, and rock varnish micromorphological data indicate that central-eastern California and western Nevada experienced a moisture-effective period during the late Pleistocene but after the Tioga maximum, and perhaps as Tioga glaciers receded from the mouth of Pine Creek canyon. Varnishes on Tahoeage morainal boulders at Pine Creek have cation-ratio ages of about 143,000-156,000 yr B.P., suggesting that the Tahoe glaciation should not be correlated with oxygen-isotope stage 4 in the early Wisconsin, but rather with stage 6. Varnishes on morainal boulders of an older glaciation at Pine Creek are dated by cation ratio at about 182,000-187,000 yr B.P. ?? 1987.

  13. Variation in the Volatile Profiles of Black and Manchurian Ash in Relation to Emerald Ash Borer Oviposition Preferences.

    Science.gov (United States)

    Rigsby, Chad M; McCartney, Nathaniel B; Herms, Daniel A; Tumlinson, James H; Cipollini, Don

    2017-08-01

    Emerald ash borer (EAB; Agrilus planipennis) is a devastating pest of ash (Fraxinus spp.) in its invaded range in North America. Its coevolved Asian hosts are more resistant and less preferred for oviposition than susceptible North American species. We compared EAB oviposition preferences and bark and canopy volatile organic compound (VOC) emissions of resistant Manchurian ash and susceptible black ash, and examined relationships between VOC profiles and oviposition. In the field, black ash was highly preferred for oviposition while no eggs were laid on Manchurian ash, and we found clear differences in the VOC profiles of Manchurian and black ash. We detected 78 compounds emitted from these species, including 16 compounds that elicited EAB antennal activity in prior studies. Four compounds were unique to black and 11 to Manchurian ash. Emission rates of 14 canopy and 19 bark volatiles varied among the two species, including four previously reported as antennally active. Specifically, 7-epi-sesquithujene (bark) emissions were greater from black ash, while β-caryophyllene (canopy), linalool (bark), and α-cubebene (bark) were emitted at higher rates by Manchurian ash. No relationships were found between the emission rate of any single compound or group of compounds (e.g. monoterpenes) suggesting that preference may be based on complex profile combinations. This is the first study to directly compare VOCs of black and Manchurian ash as well as the first to examine bark- and canopy-specific VOCs. The unique bark and canopy VOC profiles of these two species implicates potentially important variation in VOCs between a closely related resistant and susceptible species that provides a foundation for future studies of host preferences of EAB.

  14. POTENTIAL FOR INVASION OF UNDERGROUND SOURCES OF DRINKING WATER THROUGH MUD-PLUGGED WELLS: AN EXPERIMENTAL APPRAISAL

    Science.gov (United States)

    The main objective of the feasibility study described here was to test the hypothesis that properly plugged wells are effectively sealed by drilling mud. In The process of testing the hypothesis, evidence about dynamics of building mud cake on the wellbore-face was obtained, as ...

  15. The effect of drilling muds on the environment in conditions of the extreme North

    Energy Technology Data Exchange (ETDEWEB)

    Kuzmin, Yu I; Bratishko, Yu A; Voytenko, V S

    1983-01-01

    The results are cited of experimental studies of the effect of drilling muds on individual links in tundra biogeocenoses (soil, vegetation and bodies of water) The most toxic components (chromates, fusel oil and so on) are identified. The negative effect of the drilling mud on the life of lichens and on the change in the ecological situation in the bodies of water is shown.

  16. Mud Volcanoes - A New Class of Sites for Geological and Astrobiological Exploration of Mars

    Science.gov (United States)

    Allen, C.C.; Oehler, D.Z.; Baker, D.M.

    2009-01-01

    Mud volcanoes provide a unique low-temperature window into the Earth s subsurface - including the deep biosphere - and may prove to be significant sources of atmospheric methane. The identification of analogous features on Mars would provide an important new class of sites for geological and astrobiological exploration. We report new work suggesting that features in Acidalia Planitia are most consistent with their being mud volcanoes.

  17. Composites based on PET and red mud residues as catalyst for organic removal from water

    Energy Technology Data Exchange (ETDEWEB)

    Bento, Natálya I.; Santos, Patrícia S.C. [Science and Technology Institute, Federal University of Alfenas, Rodovia José Aurélio Vilela, 11999, BR 267, Km 533, CEP 37715-400 Poços de Caldas, MG (Brazil); Souza, Talita E. de; Oliveira, Luiz C.A. [Department of Chemistry, Federal University of Minas Gerais, UFMG, Av. Antônio Carlos, 6627, Pampulha, 31270-901 Belo Horizonte, MG (Brazil); Castro, Cínthia S., E-mail: cinthia.soares.castro@gmail.com [Science and Technology Institute, Federal University of Alfenas, Rodovia José Aurélio Vilela, 11999, BR 267, Km 533, CEP 37715-400 Poços de Caldas, MG (Brazil)

    2016-08-15

    Highlights: • Composite based on carbon/iron oxide from PET and red mud wastes for organic contaminants oxidation. • Composites are mainly composed of hematite and a carbon matrix from PET decomposition. • RM/PET-15 presents the highest methylene blue (MB) removal from water, by combined adsorption and oxidation processes. • The dye oxidation was confirmed by ESI-MS studies. • The RM/PET catalysts can be reused for at least four batch runs. - Abstract: In this study, we obtained a composite based on carbon/iron oxide from red mud and PET (poly(ethylene terephthalate)) wastes by mechanical mixture (10, 15 and 20 wt.% of PET powder/red mud) followed by a controlled thermal treatment at 400 °C under air. XRD analyses revealed that the α-Fe{sub 2}O{sub 3} is the main phase formed from red mud. TPR analyses showed that the iron oxide present in the composites undergoes reduction at lower temperature to form Fe{sup 2+} species present in Fe{sub 3}O{sub 4}, indicating that the iron oxide in the composite can exhibit greater reactivity in the catalytic processes compared to the original red mud. In fact, catalytic tests showed that the composites presented higher capacity to remove methylene blue dye (MB), presenting about 90% of removal after 24 h of reaction. The MB removal was also monitored by mass spectrometer with ionization via electrospray (ESI-MS), which demonstrated the occurrence of the oxidation process, showing the formation of MB oxidation products. The stability of the composites was confirmed after four reuse cycles. The results seem to indicate that PET carbon deposited over the iron oxide from red mud promotes adsorption of the contaminant allowing its contact with the iron atoms and their consequent reaction.

  18. Optimizing Use of Girdled Ash Trees for Management of Low-Density Emerald Ash Borer (Coleoptera: Buprestidae) Populations.

    Science.gov (United States)

    Siegert, Nathan W; McCullough, Deborah G; Poland, Therese M; Heyd, Robert L

    2017-06-01

    Effective survey methods to detect and monitor recently established, low-density infestations of emerald ash borer, Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), remain a high priority because they provide land managers and property owners with time to implement tactics to slow emerald ash borer population growth and the progression of ash mortality. We evaluated options for using girdled ash (Fraxinus spp.) trees for emerald ash borer detection and management in a low-density infestation in a forested area with abundant green ash (F. pennsylvanica). Across replicated 4-ha plots, we compared detection efficiency of 4 versus 16 evenly distributed girdled ash trees and between clusters of 3 versus 12 girdled trees. We also examined within-tree larval distribution in 208 girdled and nongirdled trees and assessed adult emerald ash borer emergence from detection trees felled 11 mo after girdling and left on site. Overall, current-year larvae were present in 85-97% of girdled trees and 57-72% of nongirdled trees, and larval density was 2-5 times greater on girdled than nongirdled trees. Low-density emerald ash borer infestations were readily detected with four girdled trees per 4-ha, and 3-tree clusters were as effective as 12-tree clusters. Larval densities were greatest 0.5 ± 0.4 m below the base of the canopy in girdled trees and 1.3 ± 0.7 m above the canopy base in nongirdled trees. Relatively few adult emerald ash borer emerged from trees felled 11 mo after girdling and left on site through the following summer, suggesting removal or destruction of girdled ash trees may be unnecessary. This could potentially reduce survey costs, particularly in forested areas with poor accessibility. Published by Oxford University Press on behalf of Entomological Society of America 2017. This work is written by US Government employees and is in the public domain in the US.

  19. The Totumo mud volcano and its near-shore marine sedimentological setting (North Colombia) - From sedimentary volcanism to epithermal mineralization

    Science.gov (United States)

    Dill, H. G.; Kaufhold, S.

    2018-04-01

    The Holocene mud volcano exposed at Totumo (younger than 4150 ± 50 yr BP) lines up together with some other landforms of its kind along the Caribbean Coast in northern Colombia. It currently vents a mud of the silicate-phosphate-bearing sulfur-sodium chloride type. The mud volcanoes evolved in an active continental margin setting of the South American Cordillera with high seismicity and affected by pervasive neotectonic structural disturbances. During the Neogene and Quaternary linear terrigenous shoreline sediments alternating with delta deposits evolved on this mobile crustal segment between the Andes and ancient Precambrian cratons. Meso- to microtidal sedimentary settings during transgression and progradation created meta- to instable sedimentary and petrophysical conditions (e.g. overpressure and gas-bearing bubble sands), favorable for the formation of mud volcanoes, whose lithofacies is subdivided into (1) footwall facies (detritus from metabasic, -pelitic source rocks), (2) mud volcano plus lateral facies (material from deep-seated hydrothermal sources, hydrocarbon plays, and brine reflux from the sea), (3) hanging wall facies, sand characterized by a strong longshore drift. The sedimentary volcanism in the area is characterized by different temperatures of formation: (1) pre-stage (oxides, garnet, alumosilicates, tourmaline, zircon, barite, Fe sulfides and -sulfates), light (Ca sulfates, calcite, quartz, feldspar) and clay minerals (kaolinite, mica, pyrophyllite, chlorite, vermiculite) are efficient tools to determine the source of mud, to subdivide the mud volcano system as to its facies and describe its physical-chemical regime as to the temperature of formation, pH and Eh values. The mud volcano system of Totumo bridges the gap between sedimentary "volcanism" and epithermal hot spring deposits of intermediate to high sulfidation and forms a useful "guide" to hydrocarbon accumulation.

  20. Volcanic ash dosage calculator: A proof-of-concept tool to support aviation stakeholders during ash events

    Science.gov (United States)

    Dacre, H.; Prata, A.; Shine, K. P.; Irvine, E.

    2017-12-01

    The volcanic ash clouds produced by Icelandic volcano Eyjafjallajökull in April/May 2010 resulted in `no fly zones' which paralysed European aircraft activity and cost the airline industry an estimated £1.1 billion. In response to the crisis, the Civil Aviation Authority (CAA), in collaboration with Rolls Royce, produced the `safe-to-fly' chart. As ash concentrations are the primary output of dispersion model forecasts, the chart was designed to illustrate how engine damage progresses as a function of ash concentration. Concentration thresholds were subsequently derived based on previous ash encounters. Research scientists and aircraft manufactures have since recognised the importance of volcanic ash dosages; the accumulated concentration over time. Dosages are an improvement to concentrations as they can be used to identify pernicious situations where ash concentrations are acceptably low but the exposure time is long enough to cause damage to aircraft engines. Here we present a proof-of-concept volcanic ash dosage calculator; an innovative, web-based research tool, developed in close collaboration with operators and regulators, which utilises interactive data visualisation to communicate the uncertainty inherent in dispersion model simulations and subsequent dosage calculations. To calculate dosages, we use NAME (Numerical Atmospheric-dispersion Modelling Environment) to simulate several Icelandic eruption scenarios, which result in tephra dispersal across the North Atlantic, UK and Europe. Ash encounters are simulated based on flight-optimal routes derived from aircraft routing software. Key outputs of the calculator include: the along-flight dosage, exposure time and peak concentration. The design of the tool allows users to explore the key areas of uncertainty in the dosage calculation and to visualise how this changes as the planned flight path is varied. We expect that this research will result in better informed decisions from key stakeholders during

  1. Proceedings of symposium on ash in North America

    Science.gov (United States)

    Charles H. Michler; Matthew D., eds. Ginzel

    2010-01-01

    Includes 5 papers and 30 abstracts covering topics related to the biology and ecology of the ash species, ash utilization and management, emerald ash borer, and other threats to ash, and genetics and conservation of ash species. A paper titled "Population-level variation of Fraxinus americana L. is influenced by climate...

  2. A comparative study on the rheology and wave dissipation of kaolinite and natural Hendijan Coast mud, the Persian Gulf

    Science.gov (United States)

    Soltanpour, Mohsen; Samsami, Farzin

    2011-03-01

    The objective of this paper is to investigate the rheological behavior of kaolinite and Hendijan mud, located at the northwest part of the Persian Gulf, and the dissipative role of this muddy bed on surface water waves. A series of laboratory rheological tests was conducted to investigate the rheological response of mud to rotary and cyclic shear rates. While a viscoplastic Bingham model can successfully be applied for continuous controlled shear-stress tests, the rheology of fluid mud displays complex viscoelastic behavior in time-periodic motion. The comparisons of the behavior of natural Hendijan mud with commercial kaolinite show rheological similarities. A large number of laboratory wave-flume experiments were carried out with a focus on the dissipative role of the fluid mud. Assuming four rheological models of viscous, Kelvin-Voigt viscoelastic, Bingham viscoplastic, and viscoelastic-plastic for fluid mud layer, a numerical multi-layered model was applied to analyze the effects of different parameters of surface wave and muddy bed on wave attenuation. The predicted results based on different rheological models generally agree with the obtained wave-flume data implying that the adopted rheological model does not play an important role in the accuracy of prediction.

  3. Factors affecting the survival of ash (Fraxinus spp.) trees infested by emerald ash borer (Agrilus planipennis)

    Science.gov (United States)

    Kathleen S. Knight; John P. Brown; Robert P. Long

    2013-01-01

    Emerald ash borer (Agrilus planipennis) (EAB), an Asian woodboring beetle accidentally introduced in North America, has killed millions of ash (Fraxinus spp.) trees and is spreading rapidly. This study examined the effects of tree- and site-level factors on the mortality of ash trees in stands infested by EAB in OH, USA. Our data...

  4. Use of unwounded ash trees for the detection of emerald ash borer adults: EAB landing behavior

    Science.gov (United States)

    Jordan M. Marshall; Melissa J. Porter; Andrew J. Storer

    2011-01-01

    Incorporation of multiple trapping techniques and sites within a survey program is essential to adequately identify the range of emerald ash borer (EAB) (Agrilus planipennis Fairmaire) infestation. Within natural forests, EAB lands on stick band traps wrapped around girdled ash trees at a rate similar to that on unwounded ash trees. The objective of...

  5. Effects of water availability on emerald ash borer larval performance and phloem phenolics of Manchurian and black ash.

    Science.gov (United States)

    Chakraborty, Sourav; Whitehill, Justin G A; Hill, Amy L; Opiyo, Stephen O; Cipollini, Don; Herms, Daniel A; Bonello, Pierluigi

    2014-04-01

    The invasive emerald ash borer (EAB) beetle is a significant threat to the survival of North American ash. In previous work, we identified putative biochemical and molecular markers of constitutive EAB resistance in Manchurian ash, an Asian species co-evolved with EAB. Here, we employed high-throughput high-performance liquid chromatography with photodiode array detection and mass spectrometry (HPLC-PDA-MS) to characterize the induced response of soluble phloem phenolics to EAB attack in resistant Manchurian and susceptible black ash under conditions of either normal or low water availability, and the effects of water availability on larval performance. Total larval mass per tree was lower in Manchurian than in black ash. Low water increased larval numbers and mean larval mass overall, but more so in Manchurian ash. Low water did not affect levels of phenolics in either host species, but six phenolics decreased in response to EAB. In both ashes, pinoresinol A was induced by EAB, especially in Manchurian ash. Pinoresinol A and pinoresinol B were negatively correlated with each other in both species. The higher accumulation of pinoresinol A in Manchurian ash after attack may help explain the resistance of this species to EAB, but none of the responses measured here could explain increased larval performance in trees subjected to low water availability. © 2013 John Wiley & Sons Ltd.

  6. Radioactivity of natural medicinal preparations contained extracts from peat mud available in retail trade used externally.

    Science.gov (United States)

    Karpińska, Maria; Kapała, Jacek; Raciborska, Agnieszka; Kulesza, Grzegorz; Milewska, Anna; Mnich, Stanisław

    2017-08-01

    In this work were identified and measured the activity of radioactive isotopes present in medicinal preparations from peat mud and estimated the doses obtained from them during therapy. Radioactivity of 22 preparations from peat mud and 20 water samples from water of the North-East region of Poland was studied. The median of the total activity was 24.8 Bq kg -1 . Total maximal isotope activity was observed in the Iwonicka Cube 146 Bq kg -1 while considerable amounts of isotopes were found in the Kolobrzeska Peat Mud Paste 112 Bq kg -1 . The doses obtained during therapy were within the range of 11 nSv-13 μSv depending on extracts of medicinal preparations from peat mud. The probability that such a small dose would stimulate biological effects is low. However, some clinicians believe that one of the possible therapeutic mechanisms in the treatment of rheumatoid disorders is the induction of immune response by ionising radiation.

  7. Review of Ecosystem Level Impacts of Emerald Ash Borer on Black Ash Wetlands: What Does the Future Hold?

    Directory of Open Access Journals (Sweden)

    Randall K. Kolka

    2018-04-01

    Full Text Available The emerald ash borer (EAB is rapidly spreading throughout eastern North America and devastating ecosystems where ash is a component tree. This rapid and sustained loss of ash trees has already resulted in ecological impacts on both terrestrial and aquatic ecosystems and is projected to be even more severe as EAB invades black ash-dominated wetlands of the western Great Lakes region. Using two companion studies that are simulating short- and long-term EAB infestations and what is known from the literature, we synthesize our current limited understanding and predict anticipated future impacts of EAB on black ash wetlands. A key response to the die-back of mature black ash will be higher water tables and the potential for flooding and resulting changes to both the vegetation and animal communities. Although seedling planting studies have shown some possible replacement species, little is known about how the removal of black ash from the canopy will affect non-ash species growth and regeneration. Because black ash litter is relatively high in nitrogen, it is expected that there will be important changes in nutrient and carbon cycling and subsequent rates of productivity and decomposition. Changes in hydrology and nutrient and carbon cycling will have cascading effects on the biological community which have been scarcely studied. Research to address these important gaps is currently underway and should lead to alternatives to mitigate the effects of EAB on black ash wetland forests and develop management options pre- and post-EAB invasion.

  8. Developing Capacity for Cities to Adapt to a Changing Climate-a Case Study in Boulder, Colorado

    Science.gov (United States)

    Sands, R.; Groves, D. G.; Nason, M.; Pandya, R.

    2016-12-01

    The City of Boulder in Colorado has undertaken many progressive climate-related initiatives, from signing the Kyoto protocol to passing a Climate Action Tax. But as the city prepared to launch its Climate Commitment document and lead a community process, it realized that one critical group that had not been fully engaged in the process was its own staff. It became clear that for organizational change to occur and for the city to meet its goals, city staff needed to develop a deeper understanding of the importance of the climate goals while also learning better how to use these goals to guide their long-term planning. In early 2016, the city launched a year-long "Climate Leaders" initiative which comprised of a series of workshops that brought together over 70 staff members with climate scientists and experts in climate adaptation planning. The first two workshops, billed as Climate 101 and 201, reviewed the best available scientific information about climate threats and potential impacts, and worked with participants to understand how climate changes could affect diverse city functions. These interactive workshops also explored ways to help city staff feel comfortable preparing for a significantly different climate and discussed ways to communicate this information to the public. From there the group split into two tracks. A "mitigation" track focused on the ways in which Boulder could meet its aggressive emissions reduction targets. The "adaptation" track developed integrated scenarios for citywide planning to highlight Boulder's vulnerability to climate change and guide adaptation planning. Bringing these two conversations together is helping city staff to explore critical linkages between mitigation and adaptation, develop common messages to build community support for climate action, and inform comprehensive climate resiliency planning. We will describe how Boulder successfully partnered with scientists and planning experts to program a year of interactive

  9. Mineralogic-chemical and physical characteristics of the mud in Ä°zmir (western Turkey): suitability for use in pelotherapy

    Science.gov (United States)

    Çelik Karakaya, Muazzez; Karakaya, Necati

    2013-04-01

    The study conducted on peloid used spas in İzmir city region (western part of Turkey) included the investigation of the mineralogical, physico-chemical and geochemical properties of the three types of peloid samples in order to assess the suitability of the material for healing- aesthetic-related purposes. In situ formed muds in lagoons near the Aegean Sea (named as first group) and inner swamp muds (second group) unprocessed and raw have been using therapy and thermal baths. Mud and hot springs at around the Aegean Sea have been popular since ancient times for the treatment of rheumatic diseases, musculoskeletal disorders in the region. The mineralogical characteristics of the thermal muds are in accordance with the geological origin of the material and water sources. Mineralogic composition, mineral content and morphologic properties of the samples were determined by X-ray diffraction (XRD) and scanning electron microscopy (SEM-EDS). Chemical composition of the muds and thermal waters were determined by ICP-EAS and ICP-MS. Both of the sediment is fine- to medium size-grained and composed mostly of clay minerals, partially quartz, feldspar, carbonates, and halite, and rarely gypsum. The mineralogic composition of the muds controls the physico-chemical properties of the muds. Anion e.g., Cl, Br, and SO4, contents the thermal waters of the first group is extremely different and so the springs contain a high level of sodium chloride, magnesium sulphate, and calcium bicarbonate. The water temperature is 45 oC with a pH of 6.95 and electrical conductivity (EC) is 4.5 mS/lt in the first group while 71 oC with a pH 6.58 and EC is 2.52 mS/lt in the second ones. However, major and some of the trace element concentration of the mud samples are nearly similar, As, Cd, Cu, Hg, Ni, Sb, Se, T and Zn content of the first group is exceptionally lower than the second ones. And the hazardous element concentrations are extremely higher than the pharmaceutical clay in the second

  10. A New Stochastic Modeling of 3-D Mud Drapes Inside Point Bar Sands in Meandering River Deposits

    Energy Technology Data Exchange (ETDEWEB)

    Yin, Yanshu, E-mail: yys6587@126.com [Yangtze University, School of Geosciences (China)

    2013-12-15

    The environment of major sediments of eastern China oilfields is a meandering river where mud drapes inside point bar sand occur and are recognized as important factors for underground fluid flow and distribution of the remaining oil. The present detailed architectural analysis, and the related mud drapes' modeling inside a point bar, is practical work to enhance oil recovery. This paper illustrates a new stochastic modeling of mud drapes inside point bars. The method is a hierarchical strategy and composed of three nested steps. Firstly, the model of meandering channel bodies is established using the Fluvsim method. Each channel centerline obtained from the Fluvsim is preserved for the next simulation. Secondly, the curvature ratios of each meandering river at various positions are calculated to determine the occurrence of each point bar. The abandoned channel is used to characterize the geometry of each defined point bar. Finally, mud drapes inside each point bar are predicted through random sampling of various parameters, such as number, horizontal intervals, dip angle, and extended distance of mud drapes. A dataset, collected from a reservoir in the Shengli oilfield of China, was used to illustrate the mud drapes' building procedure proposed in this paper. The results show that the inner architectural elements of the meandering river are depicted fairly well in the model. More importantly, the high prediction precision from the cross validation of five drilled wells shows the practical value and significance of the proposed method.

  11. Softening behaviour of brown coal ashes. Influence of ash components and gas atmosphere

    Energy Technology Data Exchange (ETDEWEB)

    Hegermann, R; Huettinger, K J [Karlsruhe Univ. (T.H.) (Germany, F.R.). Inst. fuer Chemische Technik

    1990-03-01

    The softening behaviour of brown coal ashes during gasification is important for three reasons: (1) Formation of large agglomerates, (2) inactivation of catalytically active ash components, (3) encapsulation of parts of the coal. The softening behaviour of the ashes was studied with a high temperature dilatometer at ambient pressure in various atmospheres (air, CO{sub 2}, Ar/H{sub 2}O, Ar, H{sub 2}/H{sub 2}O, H{sub 2}) using a push-rod with a conical tip. The heating rate was 5 Kmin{sup -1}, the final temperature 1000deg C, the residence time 1 h. (orig.).

  12. Drycon dry ash conveyor: dry bottom ash handling system with reduced operating costs and improved plant efficiency

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-07-01

    The Drycon dry bottom ash extraction system is designed to remove bottom ash beneath the furnace, cooling it without any need of water. Fresh air in countercurrent flow to the ash is used for the ash cooling. Data presented show how savings of time and costs can be achieved with this system and how a boiler efficiency can be increased using this technology. Considerable advantages in the reliability of operation with new improvements of the design are described. 7 figs.

  13. Characterization of ash pond ashes from 3rd thermal power plant by SEM/EDX and XRD methods

    OpenAIRE

    A Minjigmaa; Ts Zolzaya; E Bayanjargal; B Davaabal; J Temuujin

    2014-01-01

      Coal combustion by products from ash pond of 3rdthermal power plant of Ulaanbaatar city have been collected in 2010 and 2013 years. The ash samples have been characterized by XRD, XRF and SEM-EDX methods in order to evaluate their chemical and mineralogical composition changes with disposed times. The mineralogical composition of ash varies with time though the chemical composition of the ashes were close each other. Possibly, inefficient operating condition of the TPS shows influence on th...

  14. Organic carbon burial in a mangrove forest, margin and intertidal mud flat

    Science.gov (United States)

    Sanders, Christian J.; Smoak, Joseph M.; Naidu, A. Sathy; Sanders, Luciana M.; Patchineelam, Sambasiva R.

    2010-12-01

    The flux of total organic carbon (TOC) to depositional facies (intertidal mud flat, margin and forest) was quantified for a tropical mangrove forest in Brazil. Results indicate that these mangrove margins and intertidal mudflats are sites of large TOC accumulation, almost four times greater than the global averages for mangrove forests. The TOC burial rates were determined from organic carbon content in sediment cores which were dated using 210Pb. Burial rates were calculated to be 1129, 949, and 353 (g m -2 yr -1), for the mud flat, margin and forest, respectively. Sediment accumulation rates (SAR) were estimated to be 7.3, 5.0 and 2.8 mm yr -1. Sediment characterization (δ 13C, δ 15N, TOC/TN and mud fraction) indicated a representative mangrove system with a record of consistent organic matter flux of up to 100 years. Because of substantial burial of organic carbon in mangrove ecosystems, their role in the global carbon budget must be considered. More importantly, as climate change influences temperature and sea level, mangrove ecosystems will respond to specific climatic conditions.

  15. Study of the effect of T-80 on the parameters of clay muds used in West Kazakhstan

    Energy Technology Data Exchange (ETDEWEB)

    Akhmetshin, E A; Utebayev, B K; Yamaliyev, V U

    1982-01-01

    Results are presented of studying the effect of oxal T-80 on the standard parameters of salt-saturated muds. The optimal concentration of T-80 was revealed in treating the muds. The findings indicate that additive of oxal T-80 reduces water output by 6-15 cm/sup 3/ in 30 min. Viscosity is insignificantly reduced. The higher the mineralization, the greater the decrease in water output. For conditions of West Kazakhstan, addition of 10-20% T-80 makes it possible to cut in half the consumption of starch in treating salt-saturated clay muds.

  16. Project ash cultch: A report on optimal oyster cultch based on a prepared fly ash substratum

    International Nuclear Information System (INIS)

    Price, K.S.; Hansen, K.M.; Schlekat, C.E.

    1991-01-01

    Based on a three year study involving setting, growth, mortality, oyster condition, and metals accumulation, the evidence is extensive and convincing that stabilized coal ash is an acceptable oyster growing cultch (substratum). Oyster larvae are attracted to set on coal ash cultch at commercial fishery densities, tend to grow as well as on natural substrata (oyster shell), and are moderately more exposed to predators on the puck shaped ash materials as produced for this study. Oysters grown for one to two years on coal ash do not accumulate heavy metals and generally are in good health as measured by several biological condition indexes

  17. Spatially limited mud turbidites on the Cascadia margin: segmented earthquake ruptures?

    Directory of Open Access Journals (Sweden)

    C. Goldfinger

    2013-08-01

    Full Text Available A series of 23 thin, mostly mud-silt turbidites are found interspersed between larger, well-dated and regionally correlated paleoseismic sandy turbidites that extend along most of the Cascadia margin, northwestern United States. Investigation of the structure, distribution, and sedimentology of these thin mud-silt units supports the interpretation of these units as turbidites originating on the continental slope. Interpretation of mud turbidites is inhibited by bioturbation and lower response to analytical and imaging techniques; nevertheless most of the 23 interpreted beds exhibit most of the characteristics of coarser turbidites. These characteristics include sharp bases, fining upward sequences, darker color, increased gamma and CT density and magnetic susceptibility relative to the hemipelagic background, sparse microfossils, high lithic content, and evidence of transport from marine sources on the continental slope. New core data from sites south of Rogue Apron indicate that sandy and muddy turbidites may be correlated at least 150 km south to Trinidad Plunge Pool for the period ~ 4800 yr BP to present. Many of the mud turbidites initially described at Rogue Apron coarsen southward, becoming sandy turbidites. High-resolution Chirp seismic profiles reveal that turbidite stratigraphy along the base of the southern Cascadia continental slope is continuous, with little variation for at least 240 km along strike. The Chirp data show that turbidites along the Cascadia base of slope are ubiquitous, and likely not sourced solely from submarine canyon mouths, but may also have been delivered to the proximal abyssal plain as sheet flows from the open continental slope and coalescing local sources. Regional stratigraphy reveals that hemipelagic sedimentation rates and total Holocene turbidite thickness and mass are similar at widely separated sites, yet the total thickness of the Holocene section is greater by a factor of two in southern Cascadia

  18. Effects of Wood Ash on Soil Fungi

    DEFF Research Database (Denmark)

    Cruz Paredes, Carla

    ), copper (Cu) and nickel (Ni), is a major environmental concern. This work is part of the project ASHBACK (www.ashback.dk) which addresses the potentials and possible problems in re-distributing wood ash to the forest. The aim of this thesis was to determine the effects of biomass ash application...... in a Norway spruce forest where different amounts of wood ash were spread on the soil to study the effects on ectomycorrhizal (ECM) fungi, bioaccumulation of metals in sporocarps, and microbial communities. Laboratory microcosm experiments were run in parallel to the field studies, to compare the effects...... of wood ash with factorial additions of lime and Cd to disentangle the pH and Cd effects of wood ash amendments using community trait distributions. Barley yield, P content, and Cd content were not affected by biomass ashes. Some arbuscular mycorrhizal (AM) fungal species were reduced when biomass ashes...

  19. Mud Gas Logging In A Deep Borehole: IODP Site C0002, Nankai Trough Accretionary Prism

    Science.gov (United States)

    Toczko, S.; Hammerschmidt, S.; Maeda, L.

    2014-12-01

    Mud logging, a tool in riser drilling, makes use of the essentially "closed-circuit" drilling mud flow between the drilling platform downhole to the bit and then back to the platform for analyses of gas from the formation in the drilling mud, cuttings from downhole, and a range of safety and operational parameters to monitor downhole drilling conditions. Scientific riser drilling, with coincident control over drilling mud, downhole pressure, and returning drilling mud analyses, has now been in use aboard the scientific riser drilling vessel Chikyu since 2009. International Ocean Discovery Program (IODP) Expedition 348, as part of the goal of reaching the plate boundary fault system near ~5000 mbsf, has now extended the deep riser hole (Hole C0002 N & P) to 3058.5 mbsf. The mud gas data discussed here are from two approximately parallel boreholes, one a kick-off from the other; 860-2329 mbsf (Hole C0002N) and 2163-3058 mbsf (Hole C0002P). An approximate overlap of 166 m between the holes allows for some slight depth comparison between the two holes. An additional 55 m overlap at the top of Hole C0002P exists where a 10-5/8-inch hole was cored, and then opened to 12-1/4-inch with logging while drilling (LWD) tools (Fig. 1). There are several fault zones revealed by LWD data, confirmed in one instance by coring. One of the defining formation characteristics of Holes C0002 N/P are the strongly dipping bedding planes, typically exceeding 60º. These fault zones and bedding planes can influence the methane/ethane concentrations found in the returning drilling mud. A focused comparison of free gas in drilling mud between one interval in Hole C0002 P, drilled first with a 10 5/8-inch coring bit and again with an 12 ¼-inch logging while drilling (LWD) bit is shown. Hole C0002N above this was cased all the way from the sea floor to the kick-off section. A fault interval (in pink) was identified from the recovered core section and from LWD resistivity and gamma. The plot of

  20. Active hydrocarbon (methane) seepage at the Alboran Sea mud volcanoes indicated by specific lipid biomarkers.

    Science.gov (United States)

    Lopez-Rodriguez, C.; Stadnitskaia, A.; De Lange, G. J.; Martínez-Ruiz, F.; Comas, M.; Sinninghe Damsté, J. S.

    2012-04-01

    Mud volcanoes (MVs) and pockmark fields are known to occur in the Alboran Basin (Westernmost Mediterranean). These MVs occur above a major sedimentary depocenter that includes up to 7 km thick early Miocene to Holocene sequences. MVs located on the top of diapiric structures that originated from undercompacted Miocene clays and olistostromes. Here we provide results from geochemical data-analyses of four gravity cores acquired in the Northern Mud Volcano Field (north of the 36°N): i.e. Perejil, Kalinin and Schneiderś Heart mud expulsion structures. Extruded materials include different types of mud breccias. Specific lipid biomarkers (n-alkanes, hopanes, irregular isoprenoid hydrocarbons and Dialkyl Glycerol Diethers (DGDs) were analysed by gas chromatography (GC) and gas chromatography mass spectrometry (GC-MS). Determination of Glycerol Dialkyl Glycerol Tetraethers (GDGTs) by high performance liquid chromatography-spectrometry (HPLC-MS), and analysis of biomarker δ13C values were performed in selected samples. Lipid biomarker analysis from the three MVs revealed similar n-alkane distributions in all mud breccia intervals, showing significant hydrocarbon-derived signals and the presence of thermally immature organic-matter admixture. This suggests that similar strata fed these MVs. The hemipelagic drapes reveal comparable n-alkane distributions, suggesting that significant upward diffusion of fluids occurs. Distributions of GDGTs are generally accepted as usefull biomarkers to locate the anaerobic oxidation of methane (AOM) in marine sediments. However, our GDGT profiles only reflect the marine thaumarchaeotal signature. There seems to be no archaea producing specific GDGTs involved in AOM in the recovered interval. Evidence of recent activity (i.e., methane gas-bubbling and chemosynthetic fauna at the Perejil MV) and the presence of specific lipid biomarker related with methanotropic archaea (Irregular Isoprenoids and DGDs), however, suggest the existence of

  1. Life cycle adaption of biofuel ashes. Evaluation of new techniques for pelletizing of biofuel ashes, especially regarding operational properties and environmental effects in the forest after ash recycling. Stage 1

    International Nuclear Information System (INIS)

    Loevgren, Linnea; Lundmark, Jan-Erik; Jansson, Charlotta

    2000-11-01

    The aim of the project 'Adaptation of Wood Ashes to Recycling' is to evaluate a new technique - roll pelleting - for making wood ash suitable for reuse as a fertiliser for woodland. The project is being carried out at the forest product companies AssiDomaen and Stora Enso. The main financier is the Swedish National Energy Administration. Other financiers are AssiDomaen, Stora Enso, The Thermal Engineering Research Institute and The Forestry Research Institute of Sweden. The project has involved the construction of a full-scale roll pelleter in a mobile container and its trial operation at two Swedish pulp and paper mills. The leaching properties of the ash products were studied with a laboratory method. In addition, the effects of ash fertilisation with these products are being studied in a four-year field trial. Effects on soil pH, nutrient supply, soil water chemistry and ground vegetation are being evaluated by The Forestry Research Institute of Sweden and will be reported separately in the year 2003. In a laboratory prestudy, the leaching properties of pellets from twelve different ash products made in a laboratory prototype machine were evaluated. The ash products were made from residues from the AssiDomaen Froevi mill and the Stora Enso Fors mill. Fly ash from Froevi was used alone and mixed with green liquor sludge and lime sludge respectively. Fly ash from Fors was also used alone and mixed with coating colour. The laboratory method used for the evaluation of leaching properties is the method developed by IVL The Swedish Environmental Research Institute Ltd. The results show that the progress of the leaching of roll pelleted ash is significantly slower than for the corresponding crushed product and a reference lime product. The speed of leaching, measured as acid neutralisation capacity, ANC, was significantly lower for the roll pelleted ash compared to self-hardened and crushed ash products. Because of the high content of calcium, lime has on the whole, a

  2. Ash fusion temperatures and their association with the transformations of coal ash particles to slag

    Energy Technology Data Exchange (ETDEWEB)

    Gupta, S.K.; Wall, T.F.; Gupta, R.P. [Cooperative Research Centre for Black Coal Utilisation, Newcastle, NSW (Australia); Creelman, R.A. [Creelman (R.A.) and Associates, Sydney, NSW (Australia)

    1997-04-01

    Ash deposition on furnace walls in PF (pulverized fuel) furnaces is called slagging when it occurs in the high temperature areas of furnaces directly exposed to flame radiation and fouling in other regions such as tubes in the convection section of the boiler. There are well documented shortcomings of certain approaches relating to their uncertainties as predictive tools for plant performance such as poor repeatability and re-producibility of ash fusion measurements. The nature of physical and chemical changes occurring during melting of coal ash has been investigated in the current study to provide an alternative procedure to the ash fusion test. Shrinkage measurements are frequently used in metallurgy and ceramic science to study the physical properties of materials at high temperatures. The output of this experiment provides three to four `peaks` (maximum rate of shrinkage with temperature) of different intensity and at different temperatures which are related to melting characteristics of the sample. It was concluded that shrinkage extents exceeding 50 percent indicated that the effect of the ash particle size is of secondary importance compared to ash chemistry in determining shrinkage levels, with fine particles giving rapid shrinkage events 10 degrees C lower in temperature. (author). 7 figs., refs.

  3. Mud peeling and horizontal crack formation in drying clays

    KAUST Repository

    Style, Robert W.; Peppin, Stephen S. L.; Cocks, Alan C. F.

    2011-01-01

    equations for the depth of peeling and the time of peeling as functions of the evaporation rate. Our model predicts a simple relationship between the radius of curvature of a mud peel and the depth of peeling. The model predictions are in agreement

  4. Publication sites productive uses of combustion ash

    Science.gov (United States)

    Publication Sites Productive Uses of Combustion Ash For more information contact: e:mail: Public waste combustion ash in landfills. The new technology brief describes recent studies where ash was used

  5. Zebra mussels invade Lake Erie muds

    Science.gov (United States)

    Berkman, Paul Arthur; Haltuch, Melissa A.; Tichich, Emily; Garton, David W.; Kennedy, Gregory W.; Gannon, John E.; Mackey, Scudder D.; Fuller, Jonathan A.; Liebenthal, Dale L.

    1998-01-01

    Zebra mussels (Dreissena polymorpha) originated in western Russia but have now become widespread in Europe and North America. They are widely known for their conspicuous invasion of rocks and other hard substrates in North American and European watersheds. We have found beds of zebra mussels directly colonizing sand and mud sediments each year across hundreds of square kilometres of North America's Lake Erie. This transformation of sedimentary habitats into mussel beds represents an unforeseen change in the invasive capacity of this species.

  6. Red mud addition in the raw meal for the production of Portland cement clinker.

    Science.gov (United States)

    Tsakiridis, P E; Agatzini-Leonardou, S; Oustadakis, P

    2004-12-10

    The aim of the present research work was to investigate the possibility of adding red mud, an alkaline leaching waste, which is obtained from bauxite during the Bayer process for alumina production, in the raw meal for the production of Portland cement clinker. For that reason, two samples of raw meals were prepared: one with ordinary raw materials, as a reference sample ((PC)Ref), and another with 3.5% red mud ((PC)R/M). The effect on the reactivity of the raw mix was evaluated on the basis of the unreacted lime content in samples sintered at 1350, 1400 and 1450 degrees C. Subsequently, the clinkers were produced by sintering the two raw meals at 1450 degrees C. The results of chemical and mineralogical analyses as well as the microscopic examination showed that the use of the red mud did not affect the mineralogical characteristics of the so produced Portland cement clinker. Furthermore, both clinkers were tested by determining the grindability, setting time, compressive strength and expansibility. The hydration products were examined by XRD analysis at 2, 7, 28 and 90 days. The results of the physico-mechanical tests showed that the addition of the red mud did not negatively affect the quality of the produced cement.

  7. Multidisciplinary research for the safe fruition of an active geosite: the Salse di Nirano mud volcanoes (Northern Apennines, Italy)

    Science.gov (United States)

    Coratza, Paola; Albarello, Dario; Cipriani, Anna; Cantucci, Barbara; Castaldini, Doriano; Conventi, Marzia; Dadomo, Andrea; De Nardo, Maria Teresa; Macini, Paolo; Martinelli, Giovanni; Mesini, Ezio; Papazzoni, Cesare Andrea; Quartieri, Simona; Ricci, Tullio; Santagata, Tommaso; Sciarra, Alessandra; Vezzalini, Giovanna

    2017-04-01

    Mud volcanoes are emissions of cold mud due to the ascent to the surface of salty and muddy waters mixed with gaseous (methane) and, in minor part, fluid hydrocarbons (petroleum veils) along faults and fractures. In the Northern Apennines mud volcanoes are closely linked to the active tectonic compression associated with thrusts of regional importance. They are mostly cone-shaped and show variable geometry and size, ranging from one to few metres, and are located in 19 sites in the northwestern part of the Apennines. Particularly noteworthy is the Nirano mud volcano field, located in the Fiorano Modenese district, which, with a surface area of approximately 75,000 m2, is one of the best developed and largest mud volcano field of the entire Italian territory and among the largest in Europe; it is thus protected as natural reserve (Salse di Nirano) since 1982. The Nirano mud volcanoes are found at the bottom of an elliptical depression, interpreted as a collapse-like structure (caldera) that may have developed in response to the deflation of a shallow mud chamber triggered by several ejections and evacuation of fluid sediments. There are several individual or multiple cones within the field of the mud volcanoes of Nirano, with a rather discontinuous activity; apparatuses become dormant or even extinct whereas new vents can appear in other spots. In the research here presented about 50 vents have been mapped and few of them appeared in May 2016. The mud volcanoes of the region have been known since a long time and have always aroused great interest due to their outstanding scenic value, and, in the past the mud volcano emissions have been used in many ways. Beside their cultural value, the mud volcanoes of the study area represent a tourist attractiveness as testified by the increasing number of visitors (e.g. about 70,000 visitors in 2015 in the Salse di Nirano Natural Reserve). Numerous initiatives, targeted at various potential users, have been developed in the

  8. Effects of chemical composition of fly ash on efficiency of metal separation in ash-melting of municipal solid waste

    Energy Technology Data Exchange (ETDEWEB)

    Okada, Takashi, E-mail: t-okada@u-fukui.ac.jp [Laboratory of Solid Waste Disposal Engineering, Graduate School of Engineering, Hokkaido University, Kita 13 Nishi 8, Kita-ku, Sapporo 060-8628 (Japan); Tomikawa, Hiroki [Laboratory of Solid Waste Disposal Engineering, Graduate School of Engineering, Hokkaido University, Kita 13 Nishi 8, Kita-ku, Sapporo 060-8628 (Japan)

    2013-03-15

    Highlights: ► Separation of Pb and Zn from Fe and Cu in ash-melting of municipal solid waste. ► Molar ratio of Cl to Na and K in fly ash affected the metal-separation efficiency. ► The low molar ratio and a non-oxidative atmosphere were better for the separation. - Abstract: In the process of metal separation by ash-melting, Fe and Cu in the incineration residue remain in the melting furnace as molten metal, whereas Pb and Zn in the residue are volatilized. This study investigated the effects of the chemical composition of incineration fly ash on the metal-separation efficiency of the ash-melting process. Incineration fly ash with different chemical compositions was melted with bottom ash in a lab-scale reactor, and the efficiency with which Pb and Zn were volatilized preventing the volatilization of Fe and Cu was evaluated. In addition, the behavior of these metals was simulated by thermodynamic equilibrium calculations. Depending on the exhaust gas treatment system used in the incinerator, the relationships among Na, K, and Cl concentrations in the incineration fly ash differed, which affected the efficiency of the metal separation. The amounts of Fe and Cu volatilized decreased by the decrease in the molar ratio of Cl to Na and K in the ash, promoting metal separation. The thermodynamic simulation predicted that the chlorination volatilization of Fe and Cu was prevented by the decrease in the molar ratio, as mentioned before. By melting incineration fly ash with the low molar ratio in a non-oxidative atmosphere, most of the Pb and Zn in the ash were volatilized leaving behind Fe and Cu.

  9. Mud Volcanoes in the Martian Lowlands: Potential Windows to Fluid-Rich Samples from Depth

    Science.gov (United States)

    Oehler, Dorothy Z.; Allen, Carlton C.

    2009-01-01

    The regional setting of the Chryse-Acidalia area augurs well for a fluid-rich subsurface, accumulation of diverse rock types reflecting the wide catchment area, astrobiological prospectivity, and mud volcanism. This latter provides a mechanism for transporting samples from relatively great depth to the surface. Since mud volcanoes are not associated with extreme heat or shock pressures, materials they transport to the surface are likely to be relatively unaltered; thus such materials could contain interpretable remnants of potential martian life (e.g., organic chemical biomarkers, mineral biosignatures, or structural remains) as well as unmetamorphosed rock samples. None of the previous landings on Mars was located in an area with features identified as potential mud volcanoes (Fig. 3), but some of these features may offer targets for future missions aimed at sampling deep fluid-rich strata with potential habitable zones.

  10. Gas generation in incinerator ash; Gasbildning i aska

    Energy Technology Data Exchange (ETDEWEB)

    Arm, Maria; Lindeberg, Johanna; Rodin, Aasa; Oehrstroem, Anna; Backman, Rainer; Oehman, Marcus; Bostroem, Dan

    2006-02-15

    In recent years, explosions have occurred in certain phases of ash handling in Sweden. Investigations have revealed that hydrogen may have been present in all cases. The hydrogen is believed to be generated by chemical reactions of aluminium and other metals within the ash in the presence of water. The purpose with this study is to increase the knowledge of gas generation of incinerator ash. Thereby, guides for appropriate ash management can be introduced and the risk for further explosions prevented. The study has comprised analyses of the ash properties, such as chemical and physical composition and the pH, of ash from 14 incineration plants (mostly waste incineration plants). Different fractions of ash materials representing different parts of the process in each plant have been analysed. Furthermore, the fuel and the technical differences between the plants have been analysed. A tool for measuring the gas generation in the laboratory has been developed and the gas generation of the different ash materials at natural and increased pH was measured. Gas analyses and thermodynamic calculations have also been performed. The results showed that: bottom ash from fluidised bed boilers generated small amounts of gas at increased pH, much smaller amounts than the idle pass, cyclone and filter ash did, bottom ash from grate fired boilers generated more gas at increased pH than their cyclone ash and filter ash, with exception of the Linkoeping plant, all bio waste incineration plants generated ash with low gas generation potential, all fly ash materials with a gas generation potential of more than 10 l/kg originated from municipal waste incineration plants, filter ash that had been stored in oxygen rich environment generated significant less gas than fresh filter ash of the same origin, hardly any other gases were generated apart from hydrogen (very small amounts of acetone, furane, benzene and most likely methane were detected in some of the ash materials), there were no

  11. Radiological survey of the covered and uncovered drilling mud depository.

    Science.gov (United States)

    Jónás, Jácint; Somlai, János; Csordás, Anita; Tóth-Bodrogi, Edit; Kovács, Tibor

    2018-08-01

    In petroleum engineering, the produced drilling mud sometimes contains elevated amounts of natural radioactivity. In this study, a remediated Hungarian drilling mud depository was investigated from a radiological perspective. The depository was monitored before and after a clay layer was applied as covering. In this study, the ambient dose equivalent rate H*(10) of the depository has been measured by a Scintillator Probe (6150AD-b Dose Rate Meter). Outdoor radon concentration, radon concentration in soil gas, and in situ field radon exhalation measurements were carried out using a pulse-type ionization chamber (AlphaGUARD radon monitor). Soil gas permeability (k) measurements were carried out using the permeameter (RADON-JOK) in situ device. Geogenic radon potentials were calculated. The radionuclide content of the drilling mud and cover layer sample has been determined with an HPGe gamma-spectrometer. The gamma dose rate was estimated from the measured radionuclide concentrations and the results were compared with the measured ambient dose equivalent rate. Based on the measured results before and after covering, the ambient dose equivalent rates were 76 (67-85) nSv/h before and 86 (83-89) nSv/h after covering, radon exhalation was 9 (6-12) mBq/m 2 s before and 14 (5-28) mBq/m 2 s after covering, the outdoor radon concentrations were 11 (9-16) before and 13 (10-22) Bq/m 3 after covering and the soil gas radon concentrations were 6 (3-8) before and 24 (14-40) kBq/m 3 after covering. Soil gas permeability measurements were 1E-11 (7E-12-1E-11) and 1E-12 (5E-13-1E-12) m 2 and the calculated geogenic radon potential values were 6 (3-8) and 12 (6-21) before and after the covering. The main radionuclide concentrations of the drilling mud were C U-238 12 (10-15) Bq/kg, C Ra-226 31 (18-40) Bq/kg, C Th-232 35 (33-39) Bq/kg and C K-40 502 (356-673) Bq/kg. The same radionuclide concentrations in the clay were C U-238 31 (29-34) Bq/kg, C Ra-226 45 (40-51) Bq/kg, C Th-232 58 (55

  12. Utilization of Hospital Waste Ash in Concrete

    Directory of Open Access Journals (Sweden)

    Shazim Ali Memon

    2013-01-01

    Full Text Available Hospital waste management is a huge problem in Pakistan. The annual production of medical waste produced from health care facilities, in Pakistan, is around 250,000 tons. This research paper is intended to evaluate the feasibility of using of hospital waste ash obtained from Pakistan Institute of Medical Sciences, Rawalpindi, Pakistan, as partial replacement of cement. The main variable in this research is the amount of hospital waste ash (2, 4, 6 and 8% by weight of cement while the amount of cementitious material, water to cementitious material ratio, fine and coarse aggregate content were kept constant. Test results substantiate that hospital waste ash can be used in concrete. XRD (X-Ray Diffraction of hospital waste ash showed that it is rich in calcite while scanning electron micrographs indicated that the particles of hospital waste ash have highly irregular shape. The slump value, density of fresh concrete and water absorption decreased with the increase in the quantity of hospital waste ash in the mix. At 3 days of testing, the compressive strength of mixes with hospital waste ash was higher than the control mix while at 7 and 28 days the CM (Control Mix showed higher strength than the hospital waste ash mixes except the mix containing 2% hospital waste ash by weight of cement.

  13. Utilization of hospital waste ash in concrete

    International Nuclear Information System (INIS)

    Memon, S.; Sheikh, M.

    2013-01-01

    Hospital waste management is a huge problem in Pakistan. The annual production of medical waste produced from health care facilities, in Pakistan, is around 250,000 tons. This research paper is intended to evaluate the feasibility of using of hospital waste ash obtained from Pakistan Institute of Medical Sciences, Rawalpindi, Pakistan, as partial replacement of cement. The main variable in this research is the amount of hospital waste ash (2, 4, 6 and 8% by weight of cement) while the amount of cementitious material, water to cementitious material ratio, fine and coarse aggregate content were kept constant. Test results substantiate that hospital waste ash can be used in concrete. XRD (X-Ray Diffraction) of hospital waste ash showed that it is rich in calcite while scanning electron micrographs indicated that the particles of hospital waste ash have highly irregular shape. The slump value, density of fresh concrete and water absorption decreased with the increase in the quantity of hospital waste ash in the mix. At 3 days of testing, the compressive strength of mixes with hospital waste ash was higher than the control mix while at 7 and 28 days the CM (Control Mix) showed higher strength than the hospital waste ash mixes except the mix containing 2% hospital waste ash by weight of cement. (author)

  14. Comparative Analysis of the Use of Banana Peels and NaOH in Ph ...

    African Journals Online (AJOL)

    Ash produced from burnt banana peels were used as a substitutive for the industrial sodium hydroxide (NaOH) and potassium hydroxide, (KOH). The negative adverse effects of mud cuttings with inorganic additives on the environment have been demonstrated. The ash were observed to be environmentally more friendly ...

  15. Enhancing the rheological properties and shale inhibition behavior of water-based mud using nanosilica, multi-walled carbon nanotube, and graphene nanoplatelet

    Directory of Open Access Journals (Sweden)

    A. Aftab

    2017-06-01

    Full Text Available Five different drilling mud systems namely potassium chloride (KCl as a basic mud, KCl/partial hydrolytic polyacrylamide (PHPA, KCl/graphene nanoplatelet (GNP, KCl/nanosilica and KCl/multi-walled carbon nano tube (MWCNT were prepared and investigated for enhancement of rheological properties and shale inhibition. Nanoparticles were characterized in drilling mud using transmission electron microscope (TEM analysis. Mineralogical analysis of shale was examined by X-ray diffraction (XRD. Five shale plugs were prepared using compactor cell for the determination of shale swelling. Shale swelling was determined using the linear swell meter (LSM for 20 hours. Results revealed that basic mud and KCl/polymer mud systems shows 30% and 24% change in shale volume. MWCNT, nanosilica and GNP were added separately in the KCl mud system. 0.1 ppb of each MWCNT and nanosilica showed 32% and 33% change in shale volume. However, when the shale was interacted with WBM containing 0.1 ppb of GNP, it was found that only 10% change in shale volume occurred. The results showed that the addition of nanoparticles in the KCl mud system improved the shale inhibition. API, HPHT filtrate loss volume, plastic viscosity (PV and yield point (YP were improved using GNP. It is learned from the experimental work that small concentration of KCl with GNP can mitigate shale swelling compared to the mud contains higher concentration of KCl and PHPA in WBM. Thus, GNP can be a better choice for enhancement of WBM performance.

  16. The UZPI ash content monitoring device

    Energy Technology Data Exchange (ETDEWEB)

    Novikov, E.P.; Bezverkhii, E.A.; Mozhaev, L.G.

    1987-07-01

    This paper describes the results of industrial trials (in coal preparation plants) to establish the accuracy of the UZPI device which determines coal ash content using X-ray detection. It is designed to monitor ash content in the 4-40% range in coal with a grain size of 0-100 mm and a coal layer thickness of 50-150 mm (depending on the ash content and grain size). The ash frequently contains oxides, and although variations in magnesium, aluminium, silicon and sulfur oxides have virtually no effect on accuracy of the UZPI, changes in the levels of calcium oxides and particularly iron oxides have a considerable influence on measurement accuracy (caused by changes in their gamma ray scattering cross section values and atomic numbers). The overall sensitivity to ash content in coal varies from 1.6 to 2.4% abs./% while that to iron oxides in ash is 0.4% abs./%. Concludes that this device is suitable for use in coal preparation plants on thin layers of coal, but its efficiency is affected by external influences, e.g. fluctuations in conveyor loading.

  17. Using Integrated 2D and 3D Resistivity Imaging Methods for Illustrating the Mud-Fluid Conduits of the Wushanting Mud Volcanoes in Southwestern Taiwan

    Directory of Open Access Journals (Sweden)

    Ping-Yu Chang

    2011-01-01

    Full Text Available We conducted 2D and 3D looped resistivity surveys in the Wushanting Natural Landscape Preservation Area (WNLPA in order to understand the relationships of the mud-fluid conduits in the mud volcano system. 2D resistivity surveys were conducted along seven networked lines. Two separate C-shape looped electrode arrays surrounding the volcano craters were used in the study. First, the two 3D looped measurements were inverted separately. Yet the inverted 3D images of the mud-volcano system were inconsistent with the landscape features suggesting that artifacts perhaps appeared in the images. The 3D looped data were then combined with the 2D data for creating a global resistivity model of WNLPA. The resulting 3D image is consistent with the observed landscape features. With the resistivity model of WNLPA, we further tried to estimate the distribution of water content. The results suggest that the 3D resistivity image has the potential to resolve the dual porosity structures in the mudstone area. Last, we used a simplified WNLPA model for forward simulation in order to verify the field measurement results. We have concluded that the artifacts in the 3D looped images are in fact shadow effects from conductive objects out of the electrode loops, and that inverted images of combined 2D and 3D data provide detailed regional conductive structures in the WNLPA site.

  18. Quality characteristics of Greek fly ashes and potential uses

    Energy Technology Data Exchange (ETDEWEB)

    Skodras, G.; Grammelis, P.; Kakaras, E. [Institute for Solid Fuels Technology and Applications, Ptolemais (Greece); Karangelos, D.; Anagnostakis, M.; Hinis, E. [Nuclear Engineering Section, Mechanical Engineering Department, National Technical University of Athens, Athens (Greece)

    2007-01-15

    The main characteristics of fly ash from Greek coal-fired boilers are presented in this paper in relation to its exploitation potential. Both fuel and fly ash samples were collected and analyzed according to the ASTM Standards. Apart from the typical analyses (proximate, ultimate, ash analysis and calorific value), an ICP-AES spectrometer was used for the analysis of heavy metals in the ash. Experimental measurements in order to determine the radioactivity content of raw fuel and the fly ash were carried out as well. A representative fly ash sample from Ptolemais power plant was evaluated and tested as filler in Self-Compacting Concrete (SCC). Ashes from the Greek brown coal are classified in type C, most of the fly ash being produced in Ptolemais of Northern Greece, while the rest in Megalopolis. Ptolemais fly ash is rich in calcium compounds, while Megalopolis fly ash contains more pyrite. Increased heavy metal concentrations are observed in the fly ash samples of Greek coal. Greek fly ash appears to have not only pozzolanic but also hydraulic behaviour. Furthermore, Greek fly ash, depending on its origin, may have relatively high natural radioactivity content, reaching in the case of Megalopolis fly ash 1 kBq kg{sup -1} of {sup 226}Ra. The laboratory results showed that fly ashes can be a competitive substitute to conventional limestone filler material in SCC. Fly ash is mostly used in Greece in cement industry replacing cement clinker and aiming to the production of special types of Portland cements. However, a more aggressive utilisation strategy should be developed, since low quantities of the total produced fly ash are currently further utilised. (author)

  19. Breeding strategies for the development of emerald ash borer - resistant North American ash

    Science.gov (United States)

    Jennifer L. Koch; David W. Carey; Kathleen S. Knight; Therese Poland; Daniel A. Herms; Mary E. Mason

    2012-01-01

    The emerald ash borer (Agrilus plannipennis; EAB) is a phloem-feeding beetle that is endemic to Asia. It was discovered in North America in 2002, found almost simultaneously near Detroit, Michigan and Windsor, Ontario, Canada. Adult beetles feed on ash (Fraxinus spp.) foliage, but larval feeding on phloem, cambium, and...

  20. Outlook for ash in your forest: results of emerald ash borer research and implications for management

    Science.gov (United States)

    Kathleen S. Knight

    2014-01-01

    Since its accidental introduction near Detroit, Michigan, in the mid-1990s, emerald ash borer (EAB) has rapidly spread through much of the U.S. and adjacent Canada, leaving millions of dead ash trees in Midwestern states (4,11). Unfortunately, EAB attacks trees as small as an inch in stem diameter and it attacks all five ash species native to the region - white, green...