WorldWideScience

Sample records for arnold engineering development

  1. Potentiometric surfaces of the Arnold Engineering Development Complex Area, Arnold Air Force Base, Tennessee, May and September 2011

    Science.gov (United States)

    Haugh, Connor J.; Robinson, John A.

    2016-01-29

    Arnold Air Force Base occupies about 40,000 acres in Coffee and Franklin Counties, Tennessee. The primary mission of Arnold Air Force Base is to provide risk-reduction information in the development of aerospace products through test and evaluation. This mission is achieved in part through test facilities at Arnold Engineering Development Complex (AEDC), which occupies about 4,000 acres in the center of Arnold Air Force Base. Arnold Air Force Base is underlain by gravel and limestone aquifers, the most productive of which is the Manchester aquifer. Several volatile organic compounds, primarily chlorinated solvents, have been identified in the groundwater at Arnold Air Force Base. In 2011, the U.S. Geological Survey, in cooperation with the U.S. Air Force, Arnold Air Force Base, completed a study of groundwater flow focused on the Arnold Engineering Development Complex area. The Arnold Engineering Development Complex area is of particular concern because within this area (1) chlorinated solvents have been identified in the groundwater, (2) the aquifers are dewatered around below-grade test facilities, and (3) there is a regional groundwater divide.

  2. Future aerospace ground test facility requirements for the Arnold Engineering Development Center

    Science.gov (United States)

    Kirchner, Mark E.; Baron, Judson R.; Bogdonoff, Seymour M.; Carter, Donald I.; Couch, Lana M.; Fanning, Arthur E.; Heiser, William H.; Koff, Bernard L.; Melnik, Robert E.; Mercer, Stephen C.

    1992-01-01

    Arnold Engineering Development Center (AEDC) was conceived at the close of World War II, when major new developments in flight technology were presaged by new aerodynamic and propulsion concepts. During the past 40 years, AEDC has played a significant part in the development of many aerospace systems. The original plans were extended through the years by some additional facilities, particularly in the area of propulsion testing. AEDC now has undertaken development of a master plan in an attempt to project requirements and to plan for ground test and computational facilities over the coming 20 to 30 years. This report was prepared in response to an AEDC request that the National Research Council (NRC) assemble a committee to prepare guidance for planning and modernizing AEDC facilities for the development and testing of future classes of aerospace systems as envisaged by the U.S. Air Force.

  3. Arnold

    CERN Document Server

    Khesin, Boris A

    2014-01-01

    Vladimir Arnold, an eminent mathematician of our time, is known both for his mathematical results, which are many and prominent, and for his strong opinions, often expressed in an uncompromising and provoking manner. His dictum that "Mathematics is a part of physics where experiments are cheap" is well known. This book consists of two parts: selected articles by and an interview with Vladimir Arnold, and a collection of articles about him written by his friends, colleagues, and students. The book is generously illustrated by a large collection of photographs, some never before published. The b

  4. United States Air Force Summer Research Program -- 1991. High School Apprenticeship Program (HSAP) Reports, Volume 12: Rome Laboratory, Arnold Engineering Development Plan

    Science.gov (United States)

    1991-12-01

    convenient document retrieval and internal voice communications system. 12-12 AFOSR High School Apprenticeship Program July 22-August 16 1991 Gene ...with the computer software packages used here at Sverdrup; Gene Smith and Gail Arnold for their aid in faxing my pay voucher every two weeks. GENERAL...10M .,.n Z~ w z .; z z ZZ r3r M z X E X 2 z Y ZiMZ . Z Z Z Z X2X Z X Z X 2 rZ Z Z W: I. I 1 It W6 hfe II 1 - -- m _ V m-! ’ =t2Csu C1 M 0 oNt - ;I

  5. Engine Test Facility (ETF)

    Data.gov (United States)

    Federal Laboratory Consortium — The Air Force Arnold Engineering Development Center's Engine Test Facility (ETF) test cells are used for development and evaluation testing of propulsion systems for...

  6. From the 'Village of a Thousand Souls' to 'Race Crossing in Jamaica': Arnold Gesell, eugenics and child development.

    Science.gov (United States)

    Weizmann, Fredric

    2010-01-01

    Perhaps best known for providing age-related norms in early development, norms that are still used as a basis for measures of developmental maturity, Arnold Gesell was a key figure in developmental psychology from the 1920s through the 1950s. After examining Gesell's reputation and status in the field, we explore Gesell's changing relationship to eugenics, both in terms of Gesell's often contradictory attitudes about the role of hereditary and environmental influences in development, and in terms of the broader relationship between the eugenics movement and science.

  7. What Arnold Gesell Would Advocate Today

    Science.gov (United States)

    Bergen, Doris

    2017-01-01

    The first issue of "Childhood Education," published in 1924, included an article by the eminent physician, Arnold Gesell. In the article, "The Significance of the Nursery School" he advocated for early childhood education, indicating its importance for both promoting the development of young children and supporting and…

  8. Summer Research Program - 1996 High School Apprenticeship Program. Volume 16, Arnold Engineering Development Center

    National Research Council Canada - National Science Library

    Moore, Gary

    1996-01-01

    The United States Air Force Summer Research Program (USAF-SRP) is designed to introduce university, college, and technical institute faculty members, graduate students, and high school students to Air Force research...

  9. Summer Research Program - 1997 High School Appenticeship Program Volume 16 Arnold Engineering Development Center

    National Research Council Canada - National Science Library

    Moore, Gary

    1997-01-01

    The United States Air Force Summer Research Program (USAF-SRP) is designed to introduce university, college, and technical institute faculty members, graduate students, and high school students to Air Force research...

  10. Final Environmental Assessment Test Operations at Arnold Engineering Development Center. Volumes 1 & 2

    Science.gov (United States)

    2008-06-01

    collected in sufficient numbers (3-10 fish) to provide a 200-g composite homogenate sample of edible tissue for analysis of recommended target...Number 3411 Metal Cans Yes AA-1 3412 Metal Shipping Barrels, Drums, Kegs, and Pails Yes AA-1 3421 Cutlery Yes AA-1 3423 Hand and Edge Tools, Except

  11. Arnold Gesell's progressive vision: child hygiene, socialism and eugenics.

    Science.gov (United States)

    Harris, Ben

    2011-08-01

    In October 1913, The American Magazine published an article by Arnold Gesell that portrayed Alma, Wisconsin (his hometown) as overflowing with the mentally and morally unfit. In "The Village of a Thousand Souls", Gesell called for the observation and segregation of the unfit as a eugenic measure. This article explores the reasons behind this infamous article by someone who became a famous developmental psychologist and pediatrician. Gesell's papers at the Library of Congress reveal his socialist views of poverty, injustice, and human development. The archives of his father's photography studio at the Wisconsin Historical Society reveal his manipulation of the photographic record to fit his negative view of Alma. Typical of the era, Gesell's Progressive vision combined social control and negative eugenics with egalitarianism and the benevolent engineering of the environment.

  12. Kolmogorov-Arnold-Moser Theorem

    Indian Academy of Sciences (India)

    system (not necessarily the 2-body system). Kolmogorov was the first to provide a solution to the above general problem in a theorem formulated in 1954 (see Suggested. Reading). However, he provided only an outline of the proof. The actual proof (with all the details) turned to be quite difficult and was provided by Arnold ...

  13. Arnold Tongues in Cell Dynamics

    Science.gov (United States)

    Jensen, Mogens

    In a recent work with Leo Kadanoff we studied the synchronization between an internal and an external frequency. One obtains a highly structured diagram with details that in essence are related to the difference between rational and irrational number. The synchronized regions appear as Arnold tongues that widen as the coupling between the frequencies increases. Such tongues have been observed in many physical systems, like in the Libchaber convective cell in the basement of the University of Chicago. In biological systems, where oscillators appear in in a broad variety, very little research on Arnold tongues has been performed. We discuss single cell oscillating dynamics triggered by an external cytokine signal. When this signal is overlaid by an oscillating variation, the two oscillators might couple leading to Arnold tongue diagram. When the tongues overlap, the cell dynamics can shift between the tongues eventually leading to a chaotic response. We quantify such switching in single cell experiments and in model systems based on Gillespie simulations. Kadanoff session.

  14. Arnold Gesell and the maturation controversy.

    Science.gov (United States)

    Dalton, Thomas C

    2005-01-01

    This article examines the work of Arnold Lucius Gesell and argues that he not only paved the way for contemporary research in motor development, but that he and colleagues anticipated fundamental issues about growth that must be addressed by psychologists and neuroscientists who are committed to the advancement of developmental science. Arnold Lucius Gesell was a pioneer in developmental psychology when the field was in its infancy. He worked diligently for the rights of physically and mentally handicapped children to receive special education that would enable them to find gainful employment. Gesell's writings in books and popular magazines increased public awareness of and support for preschool education and better foster care for orphans. Despite these achievements, many of his successors have questioned his views about infant development. Developmental psychologists have criticized Gesell for proposing a stage theory of infant growth that has fallen into disfavor among contemporary researchers. His conception of development as a maturational process has been challenged for allegedly reducing complex behavioral, perceptual, and learning processes to genetic factors. The author rejects this overly simplistic interpretation and contends that Gesell's work continues to stand the test of time.

  15. Developing systems engineers

    CSIR Research Space (South Africa)

    Goncalves, D

    2008-07-01

    Full Text Available will have rendered him incapable of dealing with the majority of problems that will face him.” (Quoted in [12]). UP has applied the SPICES model, proposed by Harden et al. [12], for developing their medical curriculum. Some aspects of the model... are useful to developing systems engineers and will be considered in SE terms at a relevant level of detail. The SPICES model is contrasted against traditional medical curriculum approaches in TABLE 1. These are two extremes on a continuum. Traditional...

  16. Engineering sustainable development

    International Nuclear Information System (INIS)

    Prendergast, J.

    1993-01-01

    This article discusses sustainable development, a policy which attempts to balance environmental preservation and economic growth, and promises a way to provide a decent life for Earth's human inhabitants without destroying the global ecosystem. Sustainable development is an effort to use technology to help clean up the mess it helped make, and engineers will be central players in its success or failure. Key aspects include more efficient energy use through conservation measures and switching to renewable sources, waste minimization, much greater recycling and reuse of materials, more comprehensive economic/environmental assessments employing life-cycle analyses, and better management of resources

  17. "Very much in love": The letters of Magda Arnold and Father John Gasson.

    Science.gov (United States)

    Rodkey, Elissa N

    2017-07-01

    Magda Arnold (1903-2002), best known for her pioneering appraisal theory of emotion, belonged to the second generation of women in psychology who frequently experienced institutional sexism and career barriers. Following her religious conversion, Arnold had to contend with the additional challenge of being an openly Catholic woman in psychology at a time when Catholic academics were stigmatized. This paper announces the discovery of and relies upon a number of previously unknown primary sources on Magda Arnold, including approximately 150 letters exchanged by Arnold and Father John Gasson. This correspondence illuminates both the development of Arnold's thought and her navigation of the career challenges posed by her conversion. I argue that Gasson's emotional and intellectual support be considered as resources that helped Arnold succeed despite the discrimination she experienced. Given the romantic content of the correspondence, I also consider Arnold and Gasson in the context of other academic couples in psychology in this period and argue that religious belief ought to be further explored as a potential contributor to the resilience of women in psychology's history. © 2017 Wiley Periodicals, Inc.

  18. Environmental Engineering and Sustainable Development

    OpenAIRE

    Said Salah Eldin Elnashaie

    2018-01-01

    Chemical Engineering is a very rich discipline and it is best classified using System Theory (ST) and utilized using the Integrated System Approach (ISA). Environmental Engineering (EE) is a subsystem of Chemical Engineering and also a subsystem of Sustainable Development (SD). In this paper both EE and SD are discussed from a Chemical Engineering point of view utilizing ST and ISA.

  19. Three-dimensional tori and Arnold tongues

    Energy Technology Data Exchange (ETDEWEB)

    Sekikawa, Munehisa, E-mail: sekikawa@cc.utsunomiya-u.ac.jp [Department of Mechanical and Intelligent Engineering, Utsunomiya University, Utsunomiya-shi 321-8585 (Japan); Inaba, Naohiko [Organization for the Strategic Coordination of Research and Intellectual Property, Meiji University, Kawasaki-shi 214-8571 (Japan); Kamiyama, Kyohei [Department of Electronics and Bioinformatics, Meiji University, Kawasaki-shi 214-8571 (Japan); Aihara, Kazuyuki [Institute of Industrial Science, the University of Tokyo, Meguro-ku 153-8505 (Japan)

    2014-03-15

    This study analyzes an Arnold resonance web, which includes complicated quasi-periodic bifurcations, by conducting a Lyapunov analysis for a coupled delayed logistic map. The map can exhibit a two-dimensional invariant torus (IT), which corresponds to a three-dimensional torus in vector fields. Numerous one-dimensional invariant closed curves (ICCs), which correspond to two-dimensional tori in vector fields, exist in a very complicated but reasonable manner inside an IT-generating region. Periodic solutions emerge at the intersections of two different thin ICC-generating regions, which we call ICC-Arnold tongues, because all three independent-frequency components of the IT become rational at the intersections. Additionally, we observe a significant bifurcation structure where conventional Arnold tongues transit to ICC-Arnold tongues through a Neimark-Sacker bifurcation in the neighborhood of a quasi-periodic Hopf bifurcation (or a quasi-periodic Neimark-Sacker bifurcation) boundary.

  20. Arnold Meri : ülesanne oli mulle ebameeldiv / Arnold Meri ; interv. Rasmus Kagge

    Index Scriptorium Estoniae

    Meri, Arnold, 1919-2009

    2003-01-01

    Ilmunud ka: Infopress 17. okt. nr. 42 lk. 34. Kaitsepolitsei tunnistas Arnold Meri kahtlustatavaks genotsiidis ja tsiviilelanikevastases ründes. Intervjuu Arnold Meriga tema rollist 1949. aasta märtsiküüditamises. Lisa: Küüditamine Eestis. Kommenteerib Marko Püüa

  1. Development of engineered barrier

    Energy Technology Data Exchange (ETDEWEB)

    Chun, Kwan Sik; Cho, Won Jin; Lee, Jae Owan; Kim, Seung Soo; Kang, Mu Ja

    1999-03-01

    Engineered barrier development was carried out into the three research fields : waste form, disposal container, and buffer. The waste form field dealt with long-term leaching tests with borosilicate waste glasses surrounded by compacted bentonite. The leach rate decreased with increasing time, and was higher for the waste specimen rich in U and Na. In the container field, preliminary concepts of disposal containers were recommended by conducting structural analysis, thermal analysis, and shielding analysis, and major properties of stainless steel, copper, and titanium as a container material were surveyed. The sensitization degrees of SUS 316 and316L were lower than those of SUS 304 and 304L, respectively. The crevice corrosion of sensitized stainless steel was sensitive to the content of salt. Researches into the buffer included establishment of its performance criteria followed by investigating major properties of buffer using potential material in Korea. Experiments were made for measuring hydraulic conductivities, swelling properties, mechanical properties, thermal conductivities, pore-water chemistry properties, and adsorption properties was also investigated. (author)

  2. Development of engineered barrier

    International Nuclear Information System (INIS)

    Chun, Kwan Sik; Cho, Won Jin; Lee, Jae Owan; Kim, Seung Soo; Kang, Mu Ja

    1999-03-01

    Engineered barrier development was carried out into the three research fields : waste form, disposal container, and buffer. The waste form field dealt with long-term leaching tests with borosilicate waste glasses surrounded by compacted bentonite. The leach rate decreased with increasing time, and was higher for the waste specimen rich in U and Na. In the container field, preliminary concepts of disposal containers were recommended by conducting structural analysis, thermal analysis, and shielding analysis, and major properties of stainless steel, copper, and titanium as a container material were surveyed. The sensitization degrees of SUS 316 and 316L were lower than those of SUS 304 and 304L, respectively. The crevice corrosion of sensitized stainless steel was sensitive to the content of salt. Researches into the buffer included establishment of its performance criteria followed by investigating major properties of buffer using potential material in Korea. Experiments were made for measuring hydraulic conductivities, swelling properties, mechanical properties, thermal conductivities, pore-water chemistry properties, and adsorption properties was also investigated. (author)

  3. Accounting engineering for sustainable development

    Directory of Open Access Journals (Sweden)

    Sidornya A.

    2017-01-01

    Full Text Available The article deals with the sustainable development of industrial enterprises in Russia, accounting for sustainable industrial growth of the national economy, tools of accounting engineering aimed at creating an information basis of transformation the Russian economic model to knowledge based economy. The proposed mechanism of ownership control of industrial enterprises in the context of long-term planning of the national economy. Theoretical bases of accounting engineering, its tools are defined. A brief review of the literature on the problem of accounting engineering is provided. A practical example of the application of the accounting engineering logic for the industrial enterprise is reviewed. It describes the research results obtained during the last 25 years of Russian scientific school of accounting engineering. Conclusions and recommendations on the use of accounting engineering to sustainable development of the Russian economy are formulated.

  4. Automotive Stirling Engine Development Project

    Science.gov (United States)

    Ernst, William D.; Shaltens, Richard K.

    1997-01-01

    The development and verification of automotive Stirling engine (ASE) component and system technology is described as it evolved through two experimental engine designs: the Mod 1 and the Mod 2. Engine operation and performance and endurance test results for the Mod 1 are summarized. Mod 2 engine and component development progress is traced from the original design through hardware development, laboratory test, and vehicle installation. More than 21,000 hr of testing were accomplished, including 4800 hr with vehicles that were driven more dm 59,000 miles. Mod 2 engine dynamometer tests demonstrated that the engine system configuration had accomplished its performance goals for power (60 kW) and efficiency (38.5%) to within a few percent. Tests with the Mod 2 engine installed in a delivery van demonstrated combined metro-highway fuel economy improvements consistent with engine performance goals and the potential for low emission levels. A modified version of the Mod 2 has been identified as a manufacturable design for an ASE. As part of the ASE project, the Industry Test and Evaluation Program (ITEP), NASA Technology Utilization (TU) project, and the industry-funded Stirling Natural Gas Engine program were undertaken to transfer ASE technology to end users. The results of these technology transfer efforts are also summarized.

  5. Arnold Green: Deklaratsioon sündis suurte pingutustega / Arnold Green ; interv. Ilmar Palli

    Index Scriptorium Estoniae

    Green, Arnold, 1920-2011

    2008-01-01

    Vestlus Eesti NSV välisministri Arnold Greeniga iseseisvusdeklaratsiooni vastuvõtmisest 16. novembril 1988. aastal. Vt. samas: Eesti Nõukogude Sotsialistliku Vabariigi Ülemnõukogu deklaratsioon Eesti NSV suveräänsusest; Kuidas valmis deklaratsiooni tekst

  6. Matthew Arnold and Minimal Competency Testing.

    Science.gov (United States)

    Tuman, Myron C.

    1979-01-01

    Presents arguments by Robert Lowe and Matthew Arnold on the 19th century British "Payment by Results" Plan, whereby schools received funds for students who passed minimal competency tests. Emphasizes that the Victorian experience produced acrimonious teachers with low morale and encourages contemporary minimal testing advocates not to…

  7. Educating Engineers for Sustainable Development

    DEFF Research Database (Denmark)

    Myrdal, Christina Grann; Holgaard, Jette Egelund

    In this paper, we explore the potentials of designing engineering education activities for sustainability development based on how environmental concerns are integrated into product development processes in a company context. First we draw on a case study from the Danish company Grundfos Management...... A/S and based on their experience with product development practise and competence development of product developers, we propose a set of competences to be addressed in engineering education for sustainable development (EESD). Furthermore, we use the problem based learning philosophy as a base...

  8. Arnold Rüütel ja Toomas Hendrik Ilves raamaturiiulil

    Index Scriptorium Estoniae

    2006-01-01

    Arnold Rüütel. Tuleviku taassünd. Tallinn : Ilo, 2001; Toomas Kall. Rüütel : rahva keeles ja meeles. Tallinn : Varrak, 2006; Eesti Vabariigi President Arnold Rüütel. [Tallinn] : Ilo, 2006; Arnold Rüütel. Agraar-tööstuskompleksi areng Eesti NSV-s. Tallinn : Valgus, 1982; Arnold Rüütel. President : [valik Vabariigi Presidendi Arnold Rüütli kõnedest]. Tallinn : Eesti Keele Sihtasutus, 2003; Toomas Hendrik Ilves. Eesti jõudmine. Tallinn : Varrak, 2006

  9. Proceedings of the Annual Tri-Service Meeting for Aircraft Engine Monitoring and Diagnostics (7th) Held on 5-7 December 1978, at Arnold Engineering Development Center, Arnold AFS, Tennessee

    Science.gov (United States)

    1979-07-01

    before repair. Fewer repairs results in significantly lower overall maintenance cost. The motivations for diagnostics systems are obviously broad going...PT2 62 7 Pb/PT7M vs. PT7M/PT2 8 N1/\\/o2 vs. N2/\\rO2 - 9 "fP6 2 02. 68 vs. N21� 10 Pb/PT7!4 Vs. N2,r02 HEALTH U PS4 /PT2 Vs. N2/1r02 INDICATORS 12... Ps4 /PS3 vs. N,1`6 2 13 Wfe/Pb 2 68 vs. N2/f0 2 - 14 TTS/02 vs. N2/\\r02 *- 15 Wfe/FN0’ 6 8 (TSFC) vs, FN/62 16 N2 /%Fr 2 Vs. FN/62 17 TT5/02 vs. FN/62

  10. LDUA engineering development plan

    International Nuclear Information System (INIS)

    Engstrom, J.W.

    1994-01-01

    This document provides guidance to perform Light Duty Utility Arm (LDUA) development work and documentation required to validate the design of the LDUA System.The LDUA system will be used to deploy various types of sensors and devices to demonstrate the technology and qualify the integrated systems for operational use in the Hanford single shell tanks to characterize the waste inside and assess tank integrity

  11. Engineering research, development and technology

    International Nuclear Information System (INIS)

    1994-05-01

    The mission of the Engineering Research, Development, and Technology Program at Lawrence Livermore National Laboratory (LLNL) is to develop the technical staff, tools, and facilities needed to support current and future LLNL programs. The efforts are guided by a dual-benefit research and development strategy that supports Department of Energy missions, such as national security through nuclear deterrence and economic competitiveness through partnerships with U.S. industry. This annual report, organized by thrust area, describes the activities for the fiscal year 1993. The report provides timely summaries of objectives, methods, and results from nine thrust areas for this fiscal year: Computational Electronics and Electromagnetics; Computational Mechanics; Diagnostics and Microelectronics; Fabrication Technology; Materials Science and Engineering; Power Conversion Technologies; Nondestructive Evaluation; Remote Sensing, Imaging, and Signal Engineering; and Emerging Technologies. Separate abstracts were prepared for 47 papers in this report

  12. Transforming Engineering Education - For Innovation and Development

    DEFF Research Database (Denmark)

    Marjoram, Tony

    2013-01-01

    Engineering and technology are of vital importance in innovation, social and economic development in higher and lower income countries. Development is driven by engineering applications and infrastructure, and most innovations derive from engineering. The last 50 years has seen significant change...... of young people in engineering, and the need to develop policy perspectives on the transformation of engineering education....... in knowledge production, dissemination and application, and associated needs for engineering, and yet engineering education has changed little over this period. This paper discusses the important role of problem-based learning and humanitarian engineering in promoting the interest, enrolment and retention...

  13. Arnold Rüütel - tshelovek goda!

    Index Scriptorium Estoniae

    2001-01-01

    Saar Polli küsitlusuuringu tulemusel pidas 35% vastanuist aasta inimeseks Arnold Rüütlit. Pealk. ajalehes Molodjozh Estonii (2001) 28. dets.: "Glavnõi tshelovek", lk. 2 ; pealk. ajalehes Narvskaja Gazeta (2001) 28. dets.: "Tshelovekom goda v Estonii stal novõi prezident stranõ", lk. 3 ; pealk. ajalehes Narvskaja Nedelja (2001) 29. dets.: "Titula tshelovek goda zhiteli Estonii udostoili Arnolda Rüütelja i ben Ladena", lk. 3 ; pealk. ajalehes Severnoje Poberezhje (2001) 28. dets.: "Tshelovekom goda stal novõi prezident", lk. 3. Arvamust avaldavad Tiit Sinissaar ja Villu Reiljan

  14. Method Engineering: Engineering of Information Systems Development Methods and Tools

    NARCIS (Netherlands)

    Brinkkemper, J.N.; Brinkkemper, Sjaak

    1996-01-01

    This paper proposes the term method engineering for the research field of the construction of information systems development methods and tools. Some research issues in method engineering are identified. One major research topic in method engineering is discussed in depth: situational methods, i.e.

  15. Summer Research Program (1992). Summer Faculty Research Program (SFRP) Reports. Volume 6. Arnold Engineering Development Center, Civil Engineering Laboratory, Frank J. Seiler Research Laboratory, Wilford Hall Medical Center

    Science.gov (United States)

    1992-12-01

    sediment fauna, rhizome and stem biota (amphipods, bivalves and polychaetes), leaf periphyton ( microbiota , anemones, hydroids, ectoprocts, crustaceans...programs, the Air Force should support a small scale experiment which must be unique to the Air Force applications. If results in phase I are fruitful ,Ŕ...dissolved in the melt. This method for preparing a Li-containing neutral melt does not appear to be fruitful . RESULTS AND DISCUSSION After MEIC of acceptable

  16. Method Engineering: Engineering of Information Systems Development Methods and Tools

    OpenAIRE

    Brinkkemper, J.N.; Brinkkemper, Sjaak

    1996-01-01

    This paper proposes the term method engineering for the research field of the construction of information systems development methods and tools. Some research issues in method engineering are identified. One major research topic in method engineering is discussed in depth: situational methods, i.e. the configuration of a project approach that is tuned to the project at hand. A language and support tool for the engineering of situational methods are discussed.

  17. [Presidendipaar Ingrid ja Arnold Rüütel] / Annika Haas

    Index Scriptorium Estoniae

    Haas, Annika

    2007-01-01

    President Arnold Rüütel ja Ingrid Rüütel Briti suursaadiku Nigel Haywoodi lahkumispeol Tallinna Teaduste Akadeemia peasaalis. Foto allkiri: Presidendipaar Ingrid ja Arnold Rüütel kuulavad Briti suursaadiku Nigel Haywoodi kiidulaulu Eesti kiire arengu aadressil

  18. Arnold mängib Spielbergi filmis / Tarmo Vahter

    Index Scriptorium Estoniae

    Vahter, Tarmo

    2001-01-01

    T. Vahter:" Arnold Rüütli toetajad on lubanud vändata presidendist propagandafilmi, mis näitab meest õiges valguses. Mööda Tallinna jalutades jääb mulje, et see film on juba valmis. Siin ja seal ripuvad üleval Steven Spielbergi Tehisintellekti reklaamplakatid. Lühend A I on ju Arnold Esimene"

  19. Automotive Stirling Engine Development Program

    Science.gov (United States)

    Nightingale, N.; Ernst, W.; Richey, A.; Simetkosky, M.; Smith, G.; Antonelli, M. (Editor)

    1983-01-01

    Mod I engine testing and test results, the test of a Mod I engine in the United States, Mod I engine characterization and analysis, Mod I Transient Test Bed fuel economy, Mod I-A engine performance are discussed. Stirling engine reference engine manufacturing and reduced size studies, components and subsystems, and the study and test of low-cost casting alloys are also covered. The overall program philosophy is outlined, and data and results are presented.

  20. CT findings in Arnold-Chiari malformation

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, Y.; Nakamura, S. (Aichi Prefecture Colony, Kasugai (Japan). Central Hospital); Yamada, H.; Kageyama, N.

    1981-12-01

    CT scans of Arnold-Chiari malformations demonstrate many abnormal findings that are considered to be specific for this type of malformation. Fifty patients with Arnold-Chiari malformations were studied, and their CT findings were analyzed. This number included 14 preshunted neonatal cases and 36 post-shunted infantile cases. Craniolacunia was recognized only in the neonatal cases, but other skull changes, including scaphocephaly and petrous scalloping, were found more frequently in the infantile cases. The posterior fossa abnormality was composed of several specific changes, such as a non-visualized fourth ventricle, a lateral or upward growth of the cerebellum, or a beaking deformity of the midbrain. These findings were far more common in the infantile cases. However, in 7 neonatal cases on which CT cisternography was performed, these posterior fossa changes were well recognized in the majority of cases. Hydrocephalus was found in all cases. In half of the post-shunted infantile cases, the lateral ventricles were markedly collapsed. Characteristic features of the lateral ventricles, such as a protruding of the caudate nuclei, a pointing of the frontal and/or occipital horns, an absent septum pellucidum, or dominently dilated occipital horns, were commonly found in both neonatal and infantile cases. The subarachnoid space was remarkably widened at the retrothalamic cistern and/or the interhemispheric fissure in many cases.

  1. Optical image encryption using multilevel Arnold transform and noninterferometric imaging

    Science.gov (United States)

    Chen, Wen; Chen, Xudong

    2011-11-01

    Information security has attracted much current attention due to the rapid development of modern technologies, such as computer and internet. We propose a novel method for optical image encryption using multilevel Arnold transform and rotatable-phase-mask noninterferometric imaging. An optical image encryption scheme is developed in the gyrator transform domain, and one phase-only mask (i.e., phase grating) is rotated and updated during image encryption. For the decryption, an iterative retrieval algorithm is proposed to extract high-quality plaintexts. Conventional encoding methods (such as digital holography) have been proven vulnerably to the attacks, and the proposed optical encoding scheme can effectively eliminate security deficiency and significantly enhance cryptosystem security. The proposed strategy based on the rotatable phase-only mask can provide a new alternative for data/image encryption in the noninterferometric imaging.

  2. Systems Engineering Leadership Development: Advancing Systems Engineering Excellence

    Science.gov (United States)

    Hall, Phil; Whitfield, Susan

    2011-01-01

    This slide presentation reviews the Systems Engineering Leadership Development Program, with particular emphasis on the work being done in the development of systems engineers at Marshall Space Flight Center. There exists a lack of individuals with systems engineering expertise, in particular those with strong leadership capabilities, to meet the needs of the Agency's exploration agenda. Therefore there is a emphasis on developing these programs to identify and train systems engineers. The presentation reviews the proposed MSFC program that includes course work, and developmental assignments. The formal developmental programs at the other centers are briefly reviewed, including the Point of Contact (POC)

  3. Perspectives of ukrainian mechanical engineering development

    OpenAIRE

    Dyrda, E.; Schepetkova, A.; Galushko, O.

    2013-01-01

    Theses are devoted to problems and perspectives of Ukrainian mechanical engineering development. Role of mechanical engineering in national economy is described. Problems of mechanical engineering, such as losing the cometetive advantages, production decreasing, debts growing, ineffective assets structure, are investigated. Influence of European integration process on mechanical engineering enterprises is discussed.

  4. Career Development in Nuclear Engineering

    International Nuclear Information System (INIS)

    Sibbens, G.

    2015-01-01

    In the eighties it was not common for girls to study engineering. But a few young girls have always been fascinated by science and technical applications and dared to go for a gender untypical education. What are these female engineers doing today? This paper describes the career development of a woman, who completed her Master of Science in Nuclear Engineering, found first a job in an international company as cooperator in the research group of radiation physics and later as head of technical support and quality assurance of medical systems and then succeeded in a competition to be recruited at the European Commission (EC). There she started as an assistant for the primary standardisation of radionuclides and high-resolution alpha-particle spectrometry including the preparation of radioactive sources in the radionuclide metrology sector at the Institute for Reference Materials and Measurements of the European Commission’s Joint Research Centre and consequently published her work in scientific journals. Today, 29 years later, I am the laboratory responsible for the preparation and characterisation of nuclear targets at EC-JRC-IRMM, leading a team that has unique know-how in the preparation of thin film deposits (called targets) tailor-made for nuclear physics measurements at the EC–JRC–IRMM and international accelerator sites. High quality measurements of nuclear data and materials are being asked for in the context of nuclear safety, minimisation of high level nuclear waste and safeguards and security. The different steps of my career development and the repeated process of managing learning, work, family and leisure are presented. The career path across different jobs and responsibilities and the career progress via a certification training programme are also explained to encourage the next generation of female professionals to continue playing a vital role in nuclear science and technology. (author)

  5. "Tangible as tissue": Arnold Gesell, infant behavior, and film analysis.

    Science.gov (United States)

    Curtis, Scott

    2011-09-01

    From 1924 to 1948, developmental psychologist Arnold Gesell regularly used photographic and motion picture technologies to collect data on infant behavior. The film camera, he said, records behavior "in such coherent, authentic and measurable detail that ... the reaction patterns of infant and child become almost as tangible as tissue." This essay places his faith in the fidelity and tangibility of film, as well as his use of film as evidence, in the context of developmental psychology's professed need for legitimately scientific observational techniques. It also examines his use of these same films as educational material to promote his brand of scientific child rearing. But his analytic techniques - his methods of extracting data from the film frames - are the key to understanding the complex relationship between his theories of development and his chosen research technology.

  6. Development of an Engineering Soil Database

    Science.gov (United States)

    2017-12-27

    ER D C TR 1 7- 15 Rapid Airfield Damage Recovery (RADR) Program Development of an Engineering Soil Database En gi ne er R es ea rc...distribution is unlimited. The US Army Engineer Research and Development Center (ERDC) solves the nation’s toughest engineering and environmental...challenges. ERDC develops innovative solutions in civil and military engineering , geospatial sciences, water resources, and environmental sciences

  7. Arnold Hauser e a literatura espanhola

    Directory of Open Access Journals (Sweden)

    Mario M. González

    2010-01-01

    Full Text Available The reading of Arnold Hauser´s work, in particular his book Der Manierismus, written in 1964, that deals with Spanish literature, allows us to overcome the usual classifications found in manuals of this area based only on chronological data. Hauser calls "Mannerism" the crisis of the Renaissance, distinguishing it from European Baroque movements. Some of the Spanish authors and their works from the sixteenth and seventeenth centuries respond to the characteristics of Mannerism, if one takes into account their perspectivism, the presence of paradox, their cerebral construction, the discovery of the modern reader, their autonomy as literary works, the overcoming of the classical genders, the use of dialog, etc, and can, therefore, be seen as the basis of the literary Modernity.

  8. Educating Civil Engineers for Developing Countries

    Science.gov (United States)

    Stanley, D.

    1974-01-01

    Based on engineering teaching experience in Africa and Asia, ideas are presented on educating civil engineers for developing countries, especially those in Africa. Some of the problems facing educational planners, teachers, and students are addressed, including responsibilities of a newly graduated civil engineer, curriculum development, and…

  9. Evaluation of magnetic resonance imaging of Arnold-Chiari malformation

    Energy Technology Data Exchange (ETDEWEB)

    Yoshino, Kimihiro; Suga, Masakazu; Takemoto, Motohisa

    1987-06-01

    We evaluated the usefulness of magnetic resonance imaging (MRI) in the diagnosis of the Arnold-Chiari malformation. The patient, a 52-year-old man, complained of dizziness on walking. He initially refused to undergone myelography, but 4 months later, underwent MRI test, which lead to the diagnosis of Arnold-Chiari malformation (I type). Not all patients with symptoms of Arnold-Chiari malformation, syringomyelia, syringobulbia and cervical spinal tumor, undergone myelography, which is an invasive technique, therefore MRI should be the first examination for the patients with disorders involving the craniocervical junction.

  10. Development of Engine Loads Methodology, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR seeks to improve the definition of design loads for rocket engine components such that higher performing, lighter weight engines can be developed more...

  11. Campaign Quality Gap: Developing Strategic Engineering Competency

    National Research Council Canada - National Science Library

    Wilson, Jr, Roger A

    2007-01-01

    Recent policy developments in the Department of Defense (DOD) impose new and significant challenges for the Nation's strategic engineering directorate, the US Army Corps of Engineers (USACE). DOD Directive...

  12. Software engineering architecture-driven software development

    CERN Document Server

    Schmidt, Richard F

    2013-01-01

    Software Engineering: Architecture-driven Software Development is the first comprehensive guide to the underlying skills embodied in the IEEE's Software Engineering Body of Knowledge (SWEBOK) standard. Standards expert Richard Schmidt explains the traditional software engineering practices recognized for developing projects for government or corporate systems. Software engineering education often lacks standardization, with many institutions focusing on implementation rather than design as it impacts product architecture. Many graduates join the workforce with incomplete skil

  13. Cryogenic rocket engine development at Delft aerospace rocket engineering

    NARCIS (Netherlands)

    Wink, J; Hermsen, R.; Huijsman, R; Akkermans, C.; Denies, L.; Barreiro, F.; Schutte, A.; Cervone, A.; Zandbergen, B.T.C.

    2016-01-01

    This paper describes the current developments regarding cryogenic rocket engine technology at Delft Aerospace Rocket Engineering (DARE). DARE is a student society based at Delft University of Technology with the goal of being the first student group in the world to launch a rocket into space. After

  14. Hydrogen hybrid vehicle engine development: Experimental program

    Energy Technology Data Exchange (ETDEWEB)

    Van Blarigan, P. [Sandia National Lab., Livermore, CA (United States)

    1995-09-01

    A hydrogen fueled engine is being developed specifically for the auxiliary power unit (APU) in a series type hybrid vehicle. Hydrogen is different from other internal combustion (IC) engine fuels, and hybrid vehicle IC engine requirements are different from those of other IC vehicle engines. Together these differences will allow a new engine design based on first principles that will maximize thermal efficiency while minimizing principal emissions. The experimental program is proceeding in four steps: (1) Demonstration of the emissions and the indicated thermal efficiency capability of a standard CLR research engine modified for higher compression ratios and hydrogen fueled operation. (2) Design and test a new combustion chamber geometry for an existing single cylinder research engine, in an attempt to improve on the baseline indicated thermal efficiency of the CLR engine. (3) Design and build, in conjunction with an industrial collaborator, a new full scale research engine designed to maximize brake thermal efficiency. Include a full complement of combustion diagnostics. (4) Incorporate all of the knowledge thus obtained in the design and fabrication, by an industrial collaborator, of the hydrogen fueled engine for the hybrid vehicle power train illustrator. Results of the CLR baseline engine testing are presented, as well as preliminary data from the new combustion chamber engine. The CLR data confirm the low NOx produced by lean operation. The preliminary indicated thermal efficiency data from the new combustion chamber design engine show an improvement relative to the CLR engine. Comparison with previous high compression engine results shows reasonable agreement.

  15. [Development of domain specific search engines].

    Science.gov (United States)

    Takai, T; Tokunaga, M; Maeda, K; Kaminuma, T

    2000-01-01

    As cyber space exploding in a pace that nobody has ever imagined, it becomes very important to search cyber space efficiently and effectively. One solution to this problem is search engines. Already a lot of commercial search engines have been put on the market. However these search engines respond with such cumbersome results that domain specific experts can not tolerate. Using a dedicate hardware and a commercial software called OpenText, we have tried to develop several domain specific search engines. These engines are for our institute's Web contents, drugs, chemical safety, endocrine disruptors, and emergent response for chemical hazard. These engines have been on our Web site for testing.

  16. Sustainable Development in Engineering Education

    Science.gov (United States)

    Taoussanidis, Nikolaos N.; Antoniadou, Myrofora A.

    2006-01-01

    The principles and practice of environmentally and socially sustainable engineering are in line with growing community expectations and the strengthening voice of civil society in engineering interventions. Pressures towards internationalization and globalization are reflected in new course accreditation criteria and higher education structures.…

  17. Engineering Research in Irish Economic Development

    Science.gov (United States)

    Kelly, John

    2011-01-01

    This article summarizes the main findings and recommendations of a report published in December 2010 by the Irish Academy of Engineering (IAE). The report, representing the views of a committee of distinguished Irish engineers from a wide range of disciplines, addresses the role of engineering research in Ireland's economic development and the…

  18. How to Develop an Engineering Design Task

    Science.gov (United States)

    Dankenbring, Chelsey; Capobianco, Brenda M.; Eichinger, David

    2014-01-01

    In this article, the authors provide an overview of engineering and the engineering design process, and describe the steps they took to develop a fifth grade-level, standards-based engineering design task titled "Getting the Dirt on Decomposition." Their main goal was to focus more on modeling the discrete steps they took to create and…

  19. Interim Particulate Matter Test Method for the Determination of Particulate Matter from Gas Turbine Engines, SERDP Project WP-1538 Final Report

    Science.gov (United States)

    Under Project No. WP-1538 of the Strategic Environmental Research and Development Program, the U. S. Air Force's Arnold Engineering Development Center (AEDC) is developing an interim test method for non-volatile particulate matter (PM) specifically for the Joint Strike Fighter (J...

  20. Development of maintenance engineering system

    International Nuclear Information System (INIS)

    1995-03-01

    Department of JMTR project has developed the Maintenance Engineering System which evaluates the aging tendency of the facilities. The system is used for the repair plan and the replace period of parts, components, equipments or facilities. The system has the data-base which consists of the check data, the inspection data, the trouble data and the repair data at the JMTR since the virgin criticality. The system is utilized maintenance works and concludes the maintenance procedures for the failure components, equipments and facilities. This system has the following characteristics. (1) Anybody can operate the system as easily as word processor. (2) Data are put into by man-machine-interface. (3) The data sheets are with light color and the recognizable arrangements. (4) The system is cost-efficient using commercial personal computers and applications. The research card and the layouts of the input data sheet had been formatted. Data has been begun to be put into the system and to check its functions. The result demonstrates that the system is available for preventive maintenance at the JMTR. (author)

  1. Arnold Rüütel: 1994. aasta kevad ja suvi / Arnold Rüütel ; intervjueerinud Toivo Tootsen

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2003-01-01

    1994. aasta kevad-sügisel raadiosaate "Keskööprogramm" jaoks tehtud intervjuud Arnold Rüütliga. Vabariigi Presidendi kõne Eesti Vabariigi 85. aastapäeval Estonia teatris 24. veebruaril 2003. Fotod

  2. ICF ETF and its engineering development requirements

    International Nuclear Information System (INIS)

    Blink, J.A.; Allen, W.O.; Billman, K.

    1980-10-01

    Inertial confinement fusion driver development and ICF target physics are being intensively explored both theoretically and experimentally. However, engineering considerations of harnessing the fusion energy pulses that are an ultimate product and goal of the ICF physics program are only being addressed on a small scale. Experience with development of other new technologies indicates that engineering development time will be substantial for ICF energy converters. The authors met at Livermore in July 1980 to form an ICF Reactor Technology Working Group to address this issue. This paper outlines the current state of planning for an ICF Engineering Test Facility (ETF) and the engineering development that must precede it

  3. Model based development of engine control algorithms

    NARCIS (Netherlands)

    Dekker, H.J.; Sturm, W.L.

    1996-01-01

    Model based development of engine control systems has several advantages. The development time and costs are strongly reduced because much of the development and optimization work is carried out by simulating both engine and control system. After optimizing the control algorithm it can be executed

  4. President Arnold Rüütli avaldus / Arnold Rüütel

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2006-01-01

    Ilmunud ka: Eesti Päevaleht : Eriväljaanne Lennart Meri 29.III 1929 - 14.III 2006. Eesti Vabariigi president 1992-2001, 14. märts, lk. 2 ; Virumaa Teataja, 15. märts, lk. 11, pealk.: Presidendi avaldus 14. märtsil 2006 ; Videvik, 16. märts, lk. 1. President Arnold Rüütel teatab president Lennart Meri surmast ning avaldab kaastunnet president Lennart Meri perekonnale ja kõigile lähedastele. Samas ka: Ametlik teade

  5. Development of natural gas rotary engines

    Science.gov (United States)

    Mack, J. R.

    1991-08-01

    Development of natural gas-fueled rotary engines was pursued on the parallel paths of converted Mazda automotive engines and of establishing technology and demonstration of a test model of a larger John Deer Technologies Incorporated (JDTI) rotary engine with power capability of 250 HP per power section for future production of multi-rotor engines with power ratings 250, 500, and 1000 HP and upward. Mazda engines were converted to natural gas and were characterized by a laboratory which was followed by nearly 12,000 hours of testing in three different field installations. To develop technology for the larger JDTI engine, laboratory and engine materials testing was accomplished. Extensive combustion analysis computer codes were modified, verified, and utilized to predict engine performance, to guide parameters for actual engine design, and to identify further improvements. A single rotor test engine of 5.8 liter displacement was designed for natural gas operation based on the JDTI 580 engine series. This engine was built and tested. It ran well and essentially achieved predicted performance. Lean combustion and low NOW emission were demonstrated.

  6. The Development of Precise Engineering Surveying Technology

    Directory of Open Access Journals (Sweden)

    LI Guangyun

    2017-10-01

    Full Text Available With the construction of big science projects in China, the precise engineering surveying technology developed rapidly in the 21th century. Firstly, the paper summarized up the current development situation for the precise engineering surveying instrument and theory. Then the three typical cases of the precise engineering surveying practice such as accelerator alignment, industry measurement and high-speed railway surveying technology are focused.

  7. Interdisciplinary Integrated Engineering Development Course in HITACHI

    Science.gov (United States)

    Ojima, Masahiro

    As an example of interdisciplinary education for engineers in private companies, IED (Integrated Engineering Development) course at HITACHI Ltd. is presented. To help 30 years old or so promising engineers create a new product based on a new technology, one year term course is designed for four types of engineers; mechanical, electric & electronic, information software, and digital systems. Each course has core basic technologies plus related supplementary subjects to promote an interdisciplinary integrated engineer. Not only lectures given by university professors but heavy duty home work is also given by senior engineers of HITACHI to make them apply basic theory to practical problems. Furthermore, self development planning, leadership development program and technology-marketing project are introduced to promote human skills and business sense needed for technology leaders in company.

  8. Automotive Stirling engine development program: A success

    Science.gov (United States)

    Tabata, W. K.

    1987-01-01

    The original 5-yr Automotive Stirling Engine Development Program has been extended to 10 years due to reduced annual funding levels. With an estimated completion date of April 1988, the technical achievements and the prospectives of meeting the original program objectives are reviewed. Various other applications of this developed Stirling engine technology are also discussed.

  9. Product design and development engineering

    International Nuclear Information System (INIS)

    Lee, Kookhwan

    2008-01-01

    This book gives design of molded plastics, design of press product, design of die casting products, the application of communication terminal design, application and design of machine elements(screw, spring, bearing, gear, retaining ridge, drawing standards, KS and JIS material marks list), 3D CAD, concurrent engineering of product design, creative concept design.

  10. Creativity Development for Engineering Students

    DEFF Research Database (Denmark)

    Zhou, Chunfang; Holgaard, Jette Egelund; Kolmos, Anette

    2010-01-01

    In this paper we outline two approaches to enhance creative skills in a PBL environment at Aalborg University, Denmark. The two strategies are respectively characterized by 1) integrating creativity training into curriculum and 2) introducing real life engineering projects for students. Two cases...

  11. Light-duty diesel engine development status and engine needs

    Energy Technology Data Exchange (ETDEWEB)

    1980-08-01

    This report reviews, assesses, and summarizes the research and development status of diesel engine technology applicable to light-duty vehicles. In addition, it identifies specific basic and applied research and development needs in light-duty diesel technology and related health areas where initial or increased participation by the US Government would be desirable. The material presented in this report updates information provided in the first diesel engine status report prepared by the Aerospace Corporation for the Department of Energy in September, 1978.

  12. Membrane Engineering for Sustainable Development: A Perspective

    OpenAIRE

    Aamer Ali; Enrico Drioli; Francesca Macedonio

    2017-01-01

    Membrane engineering can offer an important contribution in realizing sustainable industrial development. It provides opportunities to redesign the conventional process of engineering in the logic of Process Intensification. Relatively new and less exploited membrane operations offer innovative solutions to the scarcity of raw materials, freshwater and energy. Here, we identify the most interesting aspects of membrane engineering in some strategic industrial sectors. Several cases of either s...

  13. Developing marketing system for civil engineering firm

    Directory of Open Access Journals (Sweden)

    Jovićević Ratko

    2006-01-01

    Full Text Available In this paper intention was to reveal insufficient connection between theory and practice in civil engineering as indispose condition for more efficient solving problems which products unstable environment of engineering firms. Successful connection between theory and practice, when we talk about marketing in civil engineering, did not develop at satisfied way. Civil engineering is, in aspect of implementation of modern philosophy of marketing, in big residue related to the other spices of economy. In that order we want to appoint on possibility to resolve this discrepancy.

  14. Development of multilayer constructs for tissue engineering

    NARCIS (Netherlands)

    Bettahalli, N. M. S.; Groen, N.; Steg, H.; Unadkat, H.; de Boer, J.; van Blitterswijk, C. A.; Wessling, M.; Stamatialis, D.

    The rapidly developing field of tissue engineering produces living substitutes that restore, maintain or improve the function of tissues or organs. In contrast to standard therapies, the engineered products become integrated within the patient, affording a potentially permanent and specific cure of

  15. Development of multilayer constructs for tissue engineering

    NARCIS (Netherlands)

    Bettahalli Narasimha, M.S.; Groen, N.; Steg, H.; Unadkat, H.V.; de Boer, Jan; van Blitterswijk, Clemens; Wessling, Matthias; Stamatialis, Dimitrios

    2014-01-01

    The rapidly developing field of tissue engineering produces living substitutes that restore, maintain or improve the function of tissues or organs. In contrast to standard therapies, the engineered products become integrated within the patient, affording a potentially permanent and specific cure of

  16. Integrated diesel engine NOx reduction technology development

    Energy Technology Data Exchange (ETDEWEB)

    Hoelzer, J.; Zhu, J.; Savonen, C.L. [Detroit Diesel Corp., MI (United States); Kharas, K.C.C.; Bailey, O.H.; Miller, M.; Vuichard, J. [Allied Signal Environmental Catalysts, Tulsa, OK (United States)

    1997-12-31

    The effectiveness of catalyst performance is a function of the inlet exhaust gas temperature, gas flow rate, concentration of NO{sub x} and oxygen, and reductant quantity and species. Given this interrelationship, it becomes immediately clear that an integrated development approach is necessary. Such an approach is taken in this project. As such, the system development path is directed by an engine-catalyst engineering team. Of the tools at the engine engineer`s disposal the real-time aspects of computer assisted subsystem modeling is valuable. It will continue to be the case as ever more subtle improvements are needed to meet competitive performance, durability, and emission challenges. A review of recent prototype engines has shown that considerable improvements to base diesel engine technology are being made. For example, HSDI NO{sub x} has been reduced by a factor of two within the past ten years. However, additional substantial NO{sub x}/PM reduction is still required for the future. A viable lean NO{sub x} catalyst would be an attractive solution to this end. The results of recent high and low temperature catalyst developments were presented. High temperature base metal catalysts have been formulated to produce very good conversion efficiency and good thermal stability, albeit at temperatures near the upper range of diesel engine operation. Low temperature noble metal catalysts have been developed to provide performance of promising 4-way control but need increased NO{sub x} reduction efficiency.

  17. Kui punane oli Arnold Rüütli punaminevik / Toomas Kümmel

    Index Scriptorium Estoniae

    Kümmel, Toomas

    2001-01-01

    EKP tippjuhtkonda kuulunud peatselt presidendi ametisse astuva Arnold Rüütli punaminevikust. Samas: Arnold Rüütli stiilinäiteid: 1987. a. avaldatud mõtted Eesti ajaloost ja 1989. a. eesti keelest

  18. Arnold Sommerfeld science, life and turbulent times : 1868-1951

    CERN Document Server

    Eckert, Michael

    2013-01-01

    Arnold Sommerfeld (1868-1951) belongs with Max Planck (1858-1947), Albert Einstein (1879-1955) and Niels Bohr (1885-1962) among the founders of modern theoretical physics, a science that developed into a budding discipline during his lifetime. Sommerfeld witnessed many of the most dramatic scientific, cultural and political events of this era. His correspondence with his family offers a vivid testament to the challenges and joys of a life in science. This biography attempts to reconstruct Sommerfeld’s life and work not only from the perspective of his achievements in theoretical physics but also with the goal of portraying the career of a scientist within the social and political environment in which it evolved. It is based to a large extent on Sommerfeld’s voluminous correspondence, which sheds light both on his private and scientific life. Furthermore, it provides an authentic view on the circumstances that shaped Sommerfeld’s career in different places – Königsberg, Göttingen, Clausthal, Aachen, ...

  19. Engineering: issues, challenges and opportunities for development

    CSIR Research Space (South Africa)

    Wall, K

    2010-10-01

    Full Text Available to contribute to greater international understanding of the issues, challenges and opportunities facing engineering, with a particular focus on contributions of our discipline to sustainable development. The Report, one of the most cost-effective reports UNESCO...

  20. United States Air Force Summer Research Program -- 1993 Summer Research Program Final Reports. Volume 11. Arnold Engineering Development Center, Frank J. Seiler Research Laboratory, Wilford Hall Medical Center

    Science.gov (United States)

    1993-01-01

    Order Polynoonlial 900 0 700-. Xr ’A S600.E:’ 500’. -400± w-i... -- 200j -: 0 0’.5 1 1.5 2 2.5 3 Equivalence Ratio (1.0 = Stoichlometric) Figure 8...0_< X < Xr Z(z,s)= eAxZ(O s) +AeA(x-xI)B C’idV-) < X2El ’Z~~2(1 e AZ(0, s) + AleA(x-x’) - eA(x-x’)]Bc’"(’), Z2 < Z ə 12- 6 The matrix exponential...H,0 is applicable to bone mineral as a whole, and (b) that bone contains 70% mineral, all in the form of hydroxyapatite , Ca, 0 (PO,)(OH),." They

  1. United States Air Force Summer Research Program 1991. Summer Faculty Research Program (SFRP) Reports. Volume 4. Rome Laboratory, Arnold Engineering Development Center, F. J. Seiler Research Laboratory

    Science.gov (United States)

    1992-01-09

    Parsing. Kaplan , D. 1975. "Quantifying in", in Davidson et al eds. The Logic of Grammar, Keenan, E. L. and L. M. Faltz 1985, Boolean Semantics for Natural...Area ( mA2 ) 100e-12 Nsrf Esrfb Phib contl type-ohmic cont2 type-ohmic Layer Descriptions Mat. X Grade Th(A) Nd Grade Edb Na Grade Eab Max Mesh algaas x

  2. Summer Research Program - 1997 Summer Faculty Research Program Volume 6 Arnold Engineering Development Center United States Air Force Academy Air Logistics Centers

    Science.gov (United States)

    1997-12-01

    Fracture Analysis of the F-5, 15%-Spar Bolt DR Devendra Kumar SAALC/LD 6- 16 CUNY-City College, New York, NY A Simple, Multiversion Concurrency Control...Program, University of Dayton, Dayton, OH. [3]AFGROW, Air Force Crack Propagation Analysis Program, Version 3.82 (1997) 15-8 A SIMPLE, MULTIVERSION ...Office of Scientific Research Boiling Air Force Base, DC and San Antonio Air Logistic Center August 1997 16-1 A SIMPLE, MULTIVERSION CONCURRENCY

  3. Assessment and Development of Engineering Design Processes

    DEFF Research Database (Denmark)

    Ulrikkeholm, Jeppe Bjerrum

    , the engineering companies need to have efficient engineering design processes in place, so they can design customised product variants faster and more efficiently. It is however not an easy task to model and develop such processes. To conduct engineering design is often a highly iterative, illdefined and complex...... the process can be fully understood and eventually improved. Taking its starting point in this proposition, the outcome of the research is an operational 5-phased procedure for assessing and developing engineering design processes through integrated modelling of product and process, designated IPPM......, and eventually the results are discussed, overall conclusions are made and future research is proposed. The results produced throughout the research project are developed in close collaboration with the Marine Low Speed business unit within the company MAN Diesel & Turbo. The business unit is the world market...

  4. Biomedical engineering for health research and development.

    Science.gov (United States)

    Zhang, X-Y

    2015-01-01

    Biomedical engineering is a new area of research in medicine and biology, providing new concepts and designs for the diagnosis, treatment and prevention of various diseases. There are several types of biomedical engineering, such as tissue, genetic, neural and stem cells, as well as chemical and clinical engineering for health care. Many electronic and magnetic methods and equipments are used for the biomedical engineering such as Computed Tomography (CT) scans, Magnetic Resonance Imaging (MRI) scans, Electroencephalography (EEG), Ultrasound and regenerative medicine and stem cell cultures, preparations of artificial cells and organs, such as pancreas, urinary bladders, liver cells, and fibroblasts cells of foreskin and others. The principle of tissue engineering is described with various types of cells used for tissue engineering purposes. The use of several medical devices and bionics are mentioned with scaffold, cells and tissue cultures and various materials are used for biomedical engineering. The use of biomedical engineering methods is very important for the human health, and research and development of diseases. The bioreactors and preparations of artificial cells or tissues and organs are described here.

  5. DATA HIDING IN ENCRYPTED IMAGES USING ARNOLD TRANSFORM

    Directory of Open Access Journals (Sweden)

    S. Siva Shankar

    2016-08-01

    Full Text Available Digital image steganography has several applications in information security and communication. Data hiding in encrypted images ensure that both the cover image and the secret message can be recovered at the receiver end. This work presents a novel data hiding and image encryption scheme using random diffusion and Two dimensional Arnold cat mapping transform. The secret message bits are placed in the least significant bit positions of the cover image. Then a shared key is used to generate random 8 bit random integer stream and is added to the stego image in the random diffusion step. Arnold cat mapping transformation is done to scramble the pixels. The two steps of random diffusion and Arnold transform mapping are done alternatively several times to completely encrypt the image contents. The process is reversed at the receiver end to get both the secret message and the cover image with little loss. The random diffusion step overcomes the limited period of the Arnold transform. The embedding capacity of one bit per pixel is achieved. Security analysis is carried out which shows that the encryption is highly secure. The number of collisions is low thus preventing brute force attacks. The original cover image is recoverable with minimal losses.

  6. Arnold : esimesed 60 aastat / Joe Wuebben ja Peter McGough ; tõlkinud Sebastian Vaikmaa

    Index Scriptorium Estoniae

    Wuebben, Joe

    2009-01-01

    Sisaldab Arnold Schwarzeneggeri biograafiat, mis on esitatud kaheosalise filmistsenaariumina; artikli osa "Täielik Arnold" on kokkuvõte 30 aasta jooksul ajakirja Muscle & Fitness rubriikides "Küsi tšempionilt" ja "Küsi Arnoldilt" ilmunud Arnold Schwarzeneggeri artiklitest jõusaalis treenimisest; artikli osa "Täis elujõudu" on kokku kogutud nimekate kulturistide tsitaate Arnold Schwarzeneggerist; artikli osa "Kaaned" sisaldab kõiki Arnold Schwarzeneggeriga Weideri kulturismiajakirjade esikaani aastatest 1968-2007 ; intervjuus räägib Schwarzenegger oma edasisest karjäärist pärast kulturismiga lõpetamist 1980.

  7. Systems engineering real estate development projects

    Science.gov (United States)

    Gusakova, Elena; Titarenko, Boris; Stepanov, Vitaliy

    2017-10-01

    In recent years, real estate development has accumulated a wealth of experience in implementing major projects, which requires comprehension and systematization. The scientific instrument of system engineering is studied in the article and is substantively interpreted with reference to real estate development projects. The most perspective approaches and models are substantiated, allowing strategically to plan the life cycle of the project as a whole, and also to solve the engineering butt problems of the project. The relevance of further scientific studies of regularities and specifics of the life cycle of real estate development projects conducted at the Moscow State University of Economics and Management at the ISTA department is shown.

  8. NNC's engineering development centre at Risley

    International Nuclear Information System (INIS)

    Garnsey, R.

    1994-01-01

    NNC's Engineering Development Centre (EDC) provides specialist engineering, manufacturing and development support to customers. EDC is located at Risley, near Warrington, but its operation are closely integrated into the Company's overall business activities based at its headquarters in Knutsford, Cheshire, fifteen miles away. EDC's facilities and expertise were originally developed to support the UK's nuclear power station construction programme. However, EDC professionals have since applied their specialist expertise to the benefit of new customers in line with the Company's diversification and a large and growing proportion of work is now in support of the defence and process industries. (author)

  9. Engineering software development with HyperCard

    Science.gov (United States)

    Darko, Robert J.

    1990-01-01

    The successful and unsuccessful techniques used in the development of software using HyperCard are described. The viability of the HyperCard for engineering is evaluated and the future use of HyperCard by this particular group of developers is discussed.

  10. Software Engineering Principles for Courseware Development.

    Science.gov (United States)

    Magel, Kenneth

    1980-01-01

    Courseware (computer based curriculum materials) development should follow the lessons learned by software engineers. The most important of 28 principles of software development presented here include a stress on human readability, the importance of early planning and analysis, the need for independent evaluation, and the need to be flexible.…

  11. Offshore Wind Energy Systems Engineering Curriculum Development

    Energy Technology Data Exchange (ETDEWEB)

    McGowan, Jon G. [Univ. of Massachusetts, Amherst, MA (United States); Manwell, James F. [Univ. of Massachusetts, Amherst, MA (United States); Lackner, Matthew A. [Univ. of Massachusetts, Amherst, MA (United States)

    2012-12-31

    Utility-scale electricity produced from offshore wind farms has the potential to contribute significantly to the energy production of the United States. In order for the U.S. to rapidly develop these abundant resources, knowledgeable scientists and engineers with sound understanding of offshore wind energy systems are critical. This report summarizes the development of an upper-level engineering course in "Offshore Wind Energy Systems Engineering." This course is designed to provide students with a comprehensive knowledge of both the technical challenges of offshore wind energy and the practical regulatory, permitting, and planning aspects of developing offshore wind farms in the U.S. This course was offered on a pilot basis in 2011 at the University of Massachusetts and the National Renewable Energy Laboratory (NREL), TU Delft, and GL Garrad Hassan have reviewed its content. As summarized in this report, the course consists of 17 separate topic areas emphasizing appropriate engineering fundamentals as well as development, planning, and regulatory issues. In addition to the course summary, the report gives the details of a public Internet site where references and related course material can be obtained. This course will fill a pressing need for the education and training of the U.S. workforce in this critically important area. Fundamentally, this course will be unique due to two attributes: an emphasis on the engineering and technical aspects of offshore wind energy systems, and a focus on offshore wind energy issues specific to the United States.

  12. Arnold Rüütli valimisplatvorm / Arnold Rüütel

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2006-01-01

    Ilmunud ka: Äripäev (2006) 13. sept., lk. 23, pealk.: Eesti peab olema inimestele turvaline kodu ; Kesknädal (2006) 13. sept., lk. 4-5, pealk.: Muudame riigi turvaliseks rahvakoduks ; Sakala (2006) 14. sept., lk. 2, pealk.: Eesti olgu inimestele turvaline kodu ; Pärnu Postimees (2006) 14. sept., lk. 15, pealk.: Eesti peab olema inimestele turvaline kodu ; Põhjarannik (2006) 14. sept., lk. 2, Eesti peab olema inimestele turvaline kodu ; Severnoje Poberezhje (2006) 14. sept., lk. 2 ; Vesti Nedeli Den za Dnjom (2006) 15. sept., lk. 20 ; Lääne-Harju Ekspress (2006) 16. sept., lk. 7 ; Hiiu Leht (2006) 19. sept., lk. 4. President Arnold Rüütel rõhutab oma valimisplatvormis, et Eesti ülim eesmärk on rahva püsimajäämine ja oma riigi hoidmine. Kommenteerib Toomas Hendrik Ilves. Lisa: Presidendikultuuri seitse alusmõtet. Ajal. Äripäev kommenteerib Aivar Hundimägi, T. H. Ilvese kommentaar ainult Eesti Päevalehes

  13. Federal Funding of Engineering Research and Development, 1980-1984.

    Science.gov (United States)

    American Society of Mechanical Engineers, Washington, DC.

    Data on the sources, amounts, and trends of federal funding for engineering research and development (R&D) are presented for 1980-1984. Narrative highlights are provided for: the total federal funding obligations for engineering R&D, mechanical engineering, astronautical engineering, aeronautical engineering, chemical engineering, civil…

  14. Development of HCCI Engines for Dimethyl Ether

    DEFF Research Database (Denmark)

    Hansen, Kim Rene; Pedersen, Troels Dyhr; Schramm, Jesper

    This report has been prepared for the Danish Energy Agency. It summarizes the results of the project entitled: “Development of HCCI engines for DME”. The project has been financed by “EFP 06”. The chapters about theoretical and experimental studies have been written using the language and termino......This report has been prepared for the Danish Energy Agency. It summarizes the results of the project entitled: “Development of HCCI engines for DME”. The project has been financed by “EFP 06”. The chapters about theoretical and experimental studies have been written using the language...

  15. Clinical and radiological findings in arnold chiari malformation

    International Nuclear Information System (INIS)

    Khan, A.A.; Bhatti, S.N.; Ahmed, E.; Aurangzeb, A.; Ali, A.; Khan, A.; Afzal, S.; Khan, G.

    2010-01-01

    Background: The Chiari Malformation I (CMI) is a disorder of uncertain origin that has been traditionally defined as downward herniation of the cerebellar tonsils through the foramen magnum. The anomaly is a leading cause of syringomyelia and occurs in association with osseous abnormalities at the cranio vertebral junction. In contrast to other Chiari malformations, CMI tends to present in the second or third decade of life and is sometimes referred to as the 'adult-type' Chiari malformation. The objective was to document clinical and radiological findings in Arnold Chiari Malformation-I. Method: This was a descriptive study carried out in Ayub Teaching Hospital Abbottabad at Neurosurgery Department during July 2008 - July 2010. We examined a prospective cohort of 60 symptomatic patients. All patients underwent magnetic resonance imaging of the head and spine. Results: There were 40 female and 20 male patients. The age of onset was 24.9 +- 15.8 years. Common associated radiological problems included syringomyelia (60%), scoliosis (25%), and basilar invagination (12%), increased cervical lordosis 5 (8.5%), and Klippel Feil syndrome 2 (3.3%). The most consistent magnetic resonance imaging findings were obliteration of the retrocerebellar cerebrospinal fluid spaces (70% patients), tonsillar herniation of at least 5 mm (100% patients), and varying degrees of post fossa anomalies. Linical manifestations were headaches, pseudotumor-like episodes, a Meniere's disease-like syndrome, lower cranial nerve signs, and spinal cord disturbances in the absence of syringomyelia. Conclusion: These data support accumulating evidence that CMI is a disorder of the para-axial mesoderm that is characterised by underdevelopment of the posterior cranial fossa and overcrowding of the normally developed hindbrain. Tonsillar herniation of less than 5 mm does not exclude the diagnosis. Clinical manifestations of CMI seem to be related to cerebrospinal fluid disturbances (which are responsible

  16. Clinical and radiological findings in arnold chiari malformation

    Energy Technology Data Exchange (ETDEWEB)

    Khan, A A; Bhatti, S N; Ahmed, E; Aurangzeb, A; Ali, A; Khan, A; Afzal, S; Khan, G [Ayub Medical College, Abbottabad (Pakistan). Department of Neurosurgery

    2010-04-15

    Background: The Chiari Malformation I (CMI) is a disorder of uncertain origin that has been traditionally defined as downward herniation of the cerebellar tonsils through the foramen magnum. The anomaly is a leading cause of syringomyelia and occurs in association with osseous abnormalities at the cranio vertebral junction. In contrast to other Chiari malformations, CMI tends to present in the second or third decade of life and is sometimes referred to as the 'adult-type' Chiari malformation. The objective was to document clinical and radiological findings in Arnold Chiari Malformation-I. Method: This was a descriptive study carried out in Ayub Teaching Hospital Abbottabad at Neurosurgery Department during July 2008 - July 2010. We examined a prospective cohort of 60 symptomatic patients. All patients underwent magnetic resonance imaging of the head and spine. Results: There were 40 female and 20 male patients. The age of onset was 24.9 +- 15.8 years. Common associated radiological problems included syringomyelia (60%), scoliosis (25%), and basilar invagination (12%), increased cervical lordosis 5 (8.5%), and Klippel Feil syndrome 2 (3.3%). The most consistent magnetic resonance imaging findings were obliteration of the retrocerebellar cerebrospinal fluid spaces (70% patients), tonsillar herniation of at least 5 mm (100% patients), and varying degrees of post fossa anomalies. Linical manifestations were headaches, pseudotumor-like episodes, a Meniere's disease-like syndrome, lower cranial nerve signs, and spinal cord disturbances in the absence of syringomyelia. Conclusion: These data support accumulating evidence that CMI is a disorder of the para-axial mesoderm that is characterised by underdevelopment of the posterior cranial fossa and overcrowding of the normally developed hindbrain. Tonsillar herniation of less than 5 mm does not exclude the diagnosis. Clinical manifestations of CMI seem to be related to cerebrospinal fluid disturbances (which are responsible

  17. Arnold-Chiari Type II Malformation: A Case Report and Review of Prenatal Sonographic Findings

    Directory of Open Access Journals (Sweden)

    Maryam Nik Nejadi

    2008-01-01

    Full Text Available The Arnold-Chiari malformation is a congenital abnormality of CNS, characterized by downwarddisplacement the parts of the cerebellum, fourth ventricle, pons and medulla oblongata into thespinal canal. This malformation is one of causative factor of death in neonates and infants. Athorough understanding of the direct and indirect sonographic findings is necessary for diagnosis ofChiari II malformation in the developing fetus.In this case report, we present a Chiari malformation II detected at 23 weeks of gestation by routinelysonographic screening. The Role of prenatal sonography in recognition of the malformation andprognostic value of these features are discussed.

  18. Developing 3D microstructures for tissue engineering

    DEFF Research Database (Denmark)

    Mohanty, Soumyaranjan

    casting process to generate various large scale tissue engineering constructs with single pore geometry with the desired mechanical stiffness and porosity. In addition, a new technique was developed to fa bricate dual-pore scaffolds for various tissue-engineering applications where 3D printing...... materials have been developed and tested for enhancing the differentiation of hiPSC-derived hepatocytes and fabricating biodegradable scaffolds for in-vivo tissue engineering applications. Along with various scaffolds fabrication methods we finally presented an optimized study of hepatic differentiation...... of hiPSC-derived DE cells cultured for 25 days in a 3D perfusion bioreactor system with an array of 16 small-scale tissue-bioreactors with integrated dual-pore pore scaffolds and flow rates. Hepatic differentiation and functionality of hiPSC-derived hepatocytes were successfully assessed and compared...

  19. Effective Software Engineering Leadership for Development Programs

    Science.gov (United States)

    Cagle West, Marsha

    2010-01-01

    Software is a critical component of systems ranging from simple consumer appliances to complex health, nuclear, and flight control systems. The development of quality, reliable, and effective software solutions requires the incorporation of effective software engineering processes and leadership. Processes, approaches, and methodologies for…

  20. Development status of the Vulcain engine

    Science.gov (United States)

    Gastal, J.; Eury, S.; Borromee, J.; Micewicz, J. B.

    1993-06-01

    The present account of the current status of the Ariane V launch vehicle's Vulcain first-stage cryofueled bipropellant engine gives attention to the Vulcain's overall configuration, as well as to its component designs, operational flowcharts, turbopump and combustion chamber performance verification trials, and program management responsibilities. Prospective development efforts currently envisioned are noted.

  1. President Arnold Rüütel lubab Eesti kreenist välja tuua / Arnold Rüütel ; intervjueerinud Henrik Roonemaa

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2001-01-01

    Eesti presidendiks valitud Arnold Rüütli sõnul on tema ja kommunism väga kauged mõisted ning lubab jätkata NATO ja EL suunal. Autor: ERL. Parlamendisaadik. Samas: Arnold Rüütli kõnest valimiskogu ees

  2. Development of engineering drawing ability for emerging engineering education

    Science.gov (United States)

    Guo, Jian-Wen; Cao, Xiao-Chang; Xie, Li; Jin, Jian-Jun; Wang, Chu-Diao

    2017-09-01

    Students majoring in engineering is required by the emerging engineering education (3E) in the aspect of their ability of engineering drawing. This paper puts forward training mode of engineering drawing ability for 3E. This mode consists of three kinds of training including training in courses, training in competitions and training in actual demand. We also design the feasible implementation plan and supplies viable references to carry out the mode.

  3. Quantum watermarking scheme through Arnold scrambling and LSB steganography

    Science.gov (United States)

    Zhou, Ri-Gui; Hu, Wenwen; Fan, Ping

    2017-09-01

    Based on the NEQR of quantum images, a new quantum gray-scale image watermarking scheme is proposed through Arnold scrambling and least significant bit (LSB) steganography. The sizes of the carrier image and the watermark image are assumed to be 2n× 2n and n× n, respectively. Firstly, a classical n× n sized watermark image with 8-bit gray scale is expanded to a 2n× 2n sized image with 2-bit gray scale. Secondly, through the module of PA-MOD N, the expanded watermark image is scrambled to a meaningless image by the Arnold transform. Then, the expanded scrambled image is embedded into the carrier image by the steganography method of LSB. Finally, the time complexity analysis is given. The simulation experiment results show that our quantum circuit has lower time complexity, and the proposed watermarking scheme is superior to others.

  4. Wind Energy Workforce Development: Engineering, Science, & Technology

    Energy Technology Data Exchange (ETDEWEB)

    Lesieutre, George A.; Stewart, Susan W.; Bridgen, Marc

    2013-03-29

    Broadly, this project involved the development and delivery of a new curriculum in wind energy engineering at the Pennsylvania State University; this includes enhancement of the Renewable Energy program at the Pennsylvania College of Technology. The new curricula at Penn State includes addition of wind energy-focused material in more than five existing courses in aerospace engineering, mechanical engineering, engineering science and mechanics and energy engineering, as well as three new online graduate courses. The online graduate courses represent a stand-alone Graduate Certificate in Wind Energy, and provide the core of a Wind Energy Option in an online intercollege professional Masters degree in Renewable Energy and Sustainability Systems. The Pennsylvania College of Technology erected a 10 kilowatt Xzeres wind turbine that is dedicated to educating the renewable energy workforce. The entire construction process was incorporated into the Renewable Energy A.A.S. degree program, the Building Science and Sustainable Design B.S. program, and other construction-related coursework throughout the School of Construction and Design Technologies. Follow-on outcomes include additional non-credit opportunities as well as secondary school career readiness events, community outreach activities, and public awareness postings.

  5. Development of Advanced Small Hydrogen Engines

    Energy Technology Data Exchange (ETDEWEB)

    Sapru, Krishna; Tan, Zhaosheng; Chao, Ben

    2010-09-30

    The main objective of the project is to develop advanced, low cost conversions of small (< 25 hp) gasoline internal combustion engines (ICEs) to run on hydrogen fuel while maintaining the same performance and durability. This final technical report summarizes the results of i) the details of the conversion of several small gasoline ICEs to run on hydrogen, ii) the durability test of a converted hydrogen engine and iii) the demonstration of a prototype bundled canister solid hydrogen storage system. Peak power of the hydrogen engine achieves 60% of the power output of the gasoline counterpart. The efforts to boost the engine power with various options including installing the over-sized turbocharger, retrofit of custom-made pistons with high compression ratio, an advanced ignition system, and various types of fuel injection systems are not realized. A converted Honda GC160 engine with ACS system to run with hydrogen fuel is successful. Total accumulative runtime is 785 hours. A prototype bundled canister solid hydrogen storage system having nominal capacity of 1.2 kg is designed, constructed and demonstrated. It is capable of supporting a wide range of output load of a hydrogen generator.

  6. Engineering Education for Sustainable Development. The Contribution of University Curricula to Engineering Education for Sustainable Development.

    NARCIS (Netherlands)

    Kastenhofer, Karen; Lansu, Angelique; Van Dam-Mieras, Rietje; Sotoudeh, Mahshid

    2010-01-01

    Global failures to reach a sustainable development within present-day societies as well as recent breakthroughs within technoscience pose new challenges to engineering education. The list of competencies which engineers should have to rise to these challenges is long and diverse, and often

  7. Develop railway engineering modules in UTK civil engineering undergraduate and graduate courses.

    Science.gov (United States)

    2015-05-31

    The importance of railway transport has long been recognized. However, no railway : engineering courses have been provided in the UTK civil engineering curricula. The : objective of this education project is to develop some railway engineering module...

  8. Difusión de Arnold en un modelo simple

    Science.gov (United States)

    Cincotta, P. M.; Nuñez, J. A.; Miloni, O.

    Investigadores como Merritt, Valluri, Pfenniger o Contopoulos (por citar los más relevantes) consideran seriamente la hipótesis que la difusión de Arnold juega un rol importante en la evolución dinámica de los sistemas estelares y planetarios. Sin embargo no existe ninguna evidencia. El mayor problema para investigar fenómenos como éste es que uno debe estudiar numéricamente sistemas multidimensionales (más de dos grados de libertad) y visualizar de alguna manera el espacio de fases (más de cuatro dimensiones). Más complicado aún es el caso de difusión de Arnold, donde deben considerarse tiempos de movimiento extremadamente largos y tratar con parámetros exponencialmente pequeños. El propósito de este trabajo es estudiar, en un modelo simple 3D, la existencia o no de difusión de Arnold mediante experimentos numéricos y estimaciones analíticas. Siguiendo los trabajos de Cincotta (2000) y Cincotta, Nuñez y Simo (2000), aquí se pretende ``visualizar" la difusión y, a la vez, determinar la escala de tiempo en la que ésta se podría manifestar. Este trabajo es el escalón inicial para luego abordar este problema en modelos.

  9. Engineering development in nuclear power plant construction

    International Nuclear Information System (INIS)

    Guenther, P.

    1979-01-01

    Proceeding from the up-to-now experience in the erection of nuclear power stations, especially of the first and second unit of the Greifswald nuclear power plant, the following essential aspects of the development of constructional engineering are discussed: (1) constructional features and criteria, (2) organizational management, (3) current status and problems in prelimary operations, and (4) possibilities of further expenditure reductions in constructing nuclear power stations

  10. Topics in singularity theory V I. Arnold's 60th anniversary collection

    CERN Document Server

    Khovanskii, A; Vassiliev, V

    1997-01-01

    "We were fortunate. We studied under Arnold. We moved in his orbit and had the opportunity to discuss with him everything under the sun. For every one of us this was a rare gift, a great good fortune in our lives." -from the Introduction Leading mathematician and expert teacher, V. I. Arnold turned 60 in June of 1997. This volume contains a selection of original papers prepared for the occasion of this 60th anniversary by former students and other participants in Arnold's Moscow seminar. A weekly event since the mid-1960s, this seminar and its participants have been inspired by Arnold's creati

  11. Protein engineering for biofuel production: Recent development

    Directory of Open Access Journals (Sweden)

    Nisha Singh

    2016-09-01

    Full Text Available The unstable and unsure handiness of crude oil sources moreover the rising price of fuels have shifted international efforts to utilize renewable resources for the assembly of greener energy and a replacement which might additionally meet the high energy demand of the globe. Biofuels represent a sustainable, renewable, and also the solely predictable energy supply to fossil fuels. During the green production of Biofuels, several in vivo processes place confidence in the conversion of biomass to sugars by engineered enzymes, and the subsequent conversion of sugars to chemicals via designed proteins in microbial production hosts. Enzymes are indispensable within the effort to provide fuels in an ecologically friendly manner. They have the potential to catalyze reactions with high specificity and potency while not using dangerous chemicals. Nature provides an in depth assortment of enzymes, however usually these should be altered to perform desired functions in needed conditions. Presently available enzymes like cellulose are subject to tight induction and regulation systems and additionally suffer inhibition from numerous end products. Therefore, more impregnable and economical catalyst preparations ought to be developed for the enzymatic method to be more economical. Approaches like protein engineering, reconstitution of protein mixtures and bio prospecting for superior enzymes are gaining importance. Advances in enzyme engineering allow the planning and/or directed evolution of enzymes specifically tailored for such industrial applications. Recent years have seen the production of improved enzymes to help with the conversion of biomass into fuels. The assembly of the many of those fuels is feasible due to advances in protein engineering. This review discusses the distinctive challenges that protein engineering faces in the method of changing lignocellulose to biofuels and the way they're addressed by recent advances in this field.

  12. Idaho National Engineering Laboratory site development plan

    International Nuclear Information System (INIS)

    1994-09-01

    This plan briefly describes the 20-year outlook for the Idaho National Engineering Laboratory (INEL). Missions, workloads, worker populations, facilities, land, and other resources necessary to fulfill the 20-year site development vision for the INEL are addressed. In addition, the plan examines factors that could enhance or deter new or expanded missions at the INEL. And finally, the plan discusses specific site development issues facing the INEL, possible solutions, resources required to resolve these issues, and the anticipated impacts if these issues remain unresolved

  13. Technology developments for a compound cycle engine

    Science.gov (United States)

    Bobula, George A.; Wintucky, William T.; Castor, J. G.

    1988-01-01

    The Compound Cycle Engine (CCE) is a highly turbocharged, power compounded power plant which combines the light weight pressure rise capability of a gas turbine with the high efficiency of a diesel. When optimized for a rotorcraft, the CCE will reduce fuel burned for a typical 2 hour (plus 30 min reserve) mission by 30 to 40 percent when compared to a conventional advanced technology gas turbine. The CCE can provide a 50 percent increase in range-payload product on this mission. Results of recent activities in a program to establish the technology base for a CCE are presented. The objective of this program is to research and develop those critical technologies which are necessary for the demonstration of a multicylinder diesel core in the early 1990s. A major accomplishment was the initial screening and identification of a lubricant which has potential for meeting the material wear rate limits of the application. An in-situ wear measurement system also was developed to provide accurate, readily obtainable, real time measurements of ring and liner wear. Wear data, from early single cylinder engine tests, are presented to show correlation of the in-situ measurements and the system's utility in determining parametric wear trends. A plan to demonstrate a compound cycle engine by the mid 1990s is included.

  14. Research and development in power plant engineering

    International Nuclear Information System (INIS)

    Riedle, K.; Taud, R.

    2001-01-01

    Research and development are a bridge for visions that are escorted to a successful market introduction. Also in power plant engineering, research and development are a lever with which the product power plant, its technology and processes can be adapted to the quickly changing future market. In the overview given by this paper, therefore at first the development boosters and targets are outlined from the viewpoint of the market; then the available technology portfolio is addressed in a concise way. Targets for the development can be seen from the support programmes of the governments. Before a preview is given, some development topics from the point of view of the manufacturer are introduced. (orig.) [de

  15. Strategic alliances in engineering, technology and development

    International Nuclear Information System (INIS)

    Jazrawi, W.

    1991-01-01

    The role of strategic alliances in the development of heavy oil resources, both mineable and in-situ, is discussed. A strategic alliance is defined as a custom designed, long term collaborative working arrangement between two parties to pool, exchange, and integrate their resources to maximize mutual gain. A combination of one or more of the following success factors is seen as contributing to the unlocking of static heavy oil resources: sufficiently high and sustained crude oil prices; strategic intent to pursue heavy oil development regardless of short-term setbacks or economic downturns; technology breakthroughs that can reduce bitumen supply and upgrading costs; and strategic alliances. An idealized model for strategic alliances designed to help develop heavy oil resources is illustrated. The advantages and pitfalls involved in strategic alliances are listed along with the characteristics of viable contract agreements for such alliances. Some examples of strategic alliances in engineering and technology development are presented from Alberta experience. 2 figs., 1 tab

  16. Sustainable Development in Engineering Education: A Pedagogical Approach

    Science.gov (United States)

    Ahrens, A.; Zascerinska, J.

    2012-01-01

    Engineering education is facing a challenge of the development of student engineers' social responsibility in the context of sustainable development. The aim of the research is to analyze efficiency of engineering curriculum in the context of sustainable development underpinning elaboration of pedagogical guidelines on the development of students'…

  17. Advancing Systems Engineering Excellence: The Marshall Systems Engineering Leadership Development Program

    Science.gov (United States)

    Hall, Philip; Whitfield, Susan

    2011-01-01

    As NASA undertakes increasingly complex projects, the need for expert systems engineers and leaders in systems engineering is becoming more pronounced. As a result of this issue, the Agency has undertaken an initiative to develop more systems engineering leaders through its Systems Engineering Leadership Development Program; however, the NASA Office of the Chief Engineer has also called on the field Centers to develop mechanisms to strengthen their expertise in systems engineering locally. In response to this call, Marshall Space Flight Center (MSFC) has developed a comprehensive development program for aspiring systems engineers and systems engineering leaders. This presentation will summarize the two-level program, which consists of a combination of training courses and on-the-job, developmental training assignments at the Center to help develop stronger expertise in systems engineering and technical leadership. In addition, it will focus on the success the program has had in its pilot year. The program hosted a formal kickoff event for Level I on October 13, 2009. The first class includes 42 participants from across MSFC and Michoud Assembly Facility (MAF). A formal call for Level II is forthcoming. With the new Agency focus on research and development of new technologies, having a strong pool of well-trained systems engineers is becoming increasingly more critical. Programs such as the Marshall Systems Engineering Leadership Development Program, as well as those developed at other Centers, help ensure that there is an upcoming generation of trained systems engineers and systems engineering leaders to meet future design challenges.

  18. Modern mechanical engineering research, development and education

    CERN Document Server

    2014-01-01

    This book covers modern subjects of mechanical engineering such as nanomechanics and nanotechnology, mechatronics and robotics, computational mechanics, biomechanics, alternative energies, sustainability as well as all aspects related with mechanical engineering education. The chapters help enhance the understanding of both the fundamentals of mechanical engineering and its application to the solution of problems in modern industry. This book is suitable for students, both in final undergraduate mechanical engineering courses or at the graduate level. It also serves as a useful reference for academics, mechanical engineering researchers, mechanical, materials and manufacturing engineers, professionals in related with mechanical engineering.

  19. Center Planning and Development Student Engineer

    Science.gov (United States)

    Jenkins, Kenneth T.

    2013-01-01

    This fall I was the Student Trainee (Engineering) Pathways Intern (co-op) at the Kennedy Space Center (KSC) in the Center Planning Development (CPD) Directorate. CPD works with commercial companies who are interested using KSCs unique capabilities in spaceflight, spacecraft processing, ground systems and Research Development (RD) projects that fall in line with NASAs mission and goals. CPD is divided into four (4) groups: (1) AD-A, which works on the Master Planning for center, (2) AD-B (where I am), which works on project management and integration, (3) AD-C, which works on partnership development, and (4) AD-T, which works on the RD aspects of partnerships. CPDs main goal is to one day make KSC the worlds largest spaceport and maintain the center as a leader in space exploration. CPD is a very diverse group with employees having a wide knowledge of not only the Space Shuttle, but also that of the Apollo era. Our director of CPD, Scott Colloredo, is on the advisory board for Commercial Space Operations (CSO) and has a degree at ERAU. I worked on a number of different tasks for AD-B, as well as CPD, that includes, but not limited to: reviewing and reissuing engineering drawings from the Apollo and Shuttle eras, to supporting NASA rocket launches (MAVEN), and working on actual agreementsproposals that will be used in the partnership process with multiple partners. Most of the work I have done is sensitive information and cannot be disclosed.

  20. Developing safety culture in nuclear power engineering

    International Nuclear Information System (INIS)

    Tevlin, S.A.

    2000-01-01

    The new issue (no. 11) of the IAEA publications series Safety Reports, devoted to the safety culture in nuclear engineering Safety culture development in the nuclear activities. Practical recommendations to achieve success, is analyzed. A number of recommendations of international experts is presented and basic general indicators of satisfactory and insufficient safety culture in the nuclear engineering are indicated. It is shown that the safety culture has two foundations: human behavior and high quality of the control system. The necessity of creating the confidence by the management at all levels of the enterprise, development of individual initiative and responsibility of the workers, which make it possible to realize the structural hierarchic system, including technical, human and organizational constituents, is noted. Three stages are traced in the process of introducing the safety culture. At the first stage the require,emts of scientific-technical documentation and provisions of the governmental, regional and control organs are fulfilled. At the second stage the management of the organization accepts the safety as an important direction in its activities. At the third stage the organization accomplishes its work, proceeding from the position of constant safety improvement. The general model of the safety culture development is considered [ru

  1. Kõrgeid ja inimlikke sihte / Arnold Rüütel

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2006-01-01

    Eesti Päevaleht lüh. Ilmunud ka: Postimees : na russkom jazõke 3. jaan. lk. 7; Pärnu Postimees 3. jaan. lk. 11; Virumaa Teataja 3. jaan. lk. 11; Järva Teataja 3. jaan. lk. 7; Võrumaa Teataja 3. jaan. lk. 2; Põhjarannik 3. jaan. lk. 2; Severnoje Poberezhje 3. jaan. lk. 2; Meie Maa 3. jaan. lk. 2; Hiiu Leht 3. jaan. lk. 2; Eesti Päevaleht 3. jaan. lk. 2; Maaleht 5. jaan. lk. 6, Lääne-Harju Ekspress 7. jaan. lk. 3. President Arnold Rüütli uusaastaläkitus

  2. Arnold Rüütel vassis taas aastaarvuga / Anneli Ammas

    Index Scriptorium Estoniae

    Ammas, Anneli, 1962-

    2006-01-01

    President Arnold Rüütel väitis 31. augusti Eesti Päevalehes, et temast sai kommunistlik noor 1949. aastal, autori sõnul algas A. Rüütli liikmelisus ELKNÜ-s juba 1946. aastal. Lähiajaloo uurija Meelis Maripuu väitel ei olnud 1946. aastal ELKNÜ veel massiorganisatsioon. Vt. samas: Varasem intervjuu - see oli 1949, pärast küüditamist; Rüütel: ma pole midagi salanud ; Ilves: Eesti vajab iga inimest. Toomas Hendrik Ilvese avaldusest seoses Johannes Hindi kohtuasja käsitlemisega ajakirjanduses

  3. Siringomielia y malformación de Arnold-Chiari

    Directory of Open Access Journals (Sweden)

    Jairo Muñoz Escobar

    1971-01-01

    Full Text Available Presentamos en este informe, nuestra experiencia en ocho casos de siringomielia en dos de ellos asociada a malformación de Arnold Chiari, que hemos analizado desde el punto de vista clínico y de los hallazgos de radiología simple y contrastada. Analizamos igualmente las técnicas quirúrgicas empleadas y los resultados obtenidos en siete casos que fueron intervenidos quirúrgicamente. Finalmente comparamos nuestros hallazgos y resultados con los mencionados en la literatura y hacemos algunos comentarios sobre fisio-patología.

  4. A Systems Engineering Approach to Architecture Development

    Science.gov (United States)

    Di Pietro, David A.

    2015-01-01

    Architecture development is often conducted prior to system concept design when there is a need to determine the best-value mix of systems that works collectively in specific scenarios and time frames to accomplish a set of mission area objectives. While multiple architecture frameworks exist, they often require use of unique taxonomies and data structures. In contrast, this paper characterizes architecture development using terminology widely understood within the systems engineering community. Using a notional civil space architecture example, it employs a multi-tier framework to describe the enterprise level architecture and illustrates how results of lower tier, mission area architectures integrate into the enterprise architecture. It also presents practices for conducting effective mission area architecture studies, including establishing the trade space, developing functions and metrics, evaluating the ability of potential design solutions to meet the required functions, and expediting study execution through the use of iterative design cycles

  5. President Arnold Rüütel : kui ma poleks president, siis oleksin talupidaja / Arnold Rüütel ; intervjueerinud Toivo Tänavsuu

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2005-01-01

    President Arnold Rüütel vastab küsimustele, mis puudutavad Ettevõtluse Auhinna konkurssi, EL-iga liitumisega kaasnenud eeliseid Eesti majandusele, lähiaastatel lahendamist vajavaid probleeme Eesti majanduses

  6. President Arnold Rüütel siirdas Kalevipojale südame / Meelis Lainvoo

    Index Scriptorium Estoniae

    Lainvoo, Meelis

    2003-01-01

    Rakvere Teatri suvelavastuse "Kalevipoeg" viimasel etendusel osalesid Arnold ja Ingrid Rüütel ning poliitikud Tõnis Palts, Tõnis Lukas, Arvo Haug ja Tõnu Kõiv. President Arnold Rüütel pani Neerutis Sadulamäel Kalevipoja kujule viimase kivi. Skulptuuri autori Seaküla Simsoni kommentaar

  7. An Awkward Echo: Matthew Arnold and John Dewey. Research in Curriculum and Instruction

    Science.gov (United States)

    Dietz, Mark David

    2010-01-01

    Matthew Arnold, 19th century English poet, literary critic and school inspector, felt that each age had to determine that philosophy that was most adequate to its own concerns and contexts. This study looks at the influence that Matthew Arnold had on John Dewey and attempts to fashion a philosophy of education that is adequate for our own…

  8. ANAESTHETIC MANAGEMENT IN A PATIENT WITH ARNOLD-CHI ARI MALFORMATION TYPE I AND SYRINGOMYELIA

    OpenAIRE

    Kartika; Pratap; Vijayalaxmi; Kalyan Chakravarthy; Nagaraju

    2013-01-01

    ABSTRACT: Syringomyelia is an unusual neurological condition characterised by the the presence of cystic cavity in the spinal cord resultin g in neurological manifestations. Here, we report a safe anesthetic management of patient with Arnold-Ch iari malformation type I and syringomyelia posted for foramen magnum decompression . INTRODUCTION: Arnold-Chiari malformation (ACM) is a developmental malformation characterised by downward displacement of cere...

  9. Johannes Hindi abil Arnold Rüütli vastu / Aare Vets

    Index Scriptorium Estoniae

    Vets, Aare

    2006-01-01

    President Arnold Rüütli vastastest rünnakutest presidendivalimiste kampaanias, näitena Eesti Ekspressis ilmunud artikkel, mille järgi Arnold Rüütel on vastutav Johannes Hindi vangistamises. J. Hindi tegevusest silikaltsiidi tootmisel ja Desintegraatori direktorina, kriminaalasja algatamisest ja karistamisest Eesti NSV-s

  10. Systems design and engineering : facilitating multidisciplinary development projects

    NARCIS (Netherlands)

    Bonnema, Gerrit Maarten; Veenvliet, Karel; Broenink, Johannes F.

    2016-01-01

    As its name implies, the aim of Systems Design and Engineering: Facilitating Multidisciplinary Development Projects is to help systems engineers develop the skills and thought processes needed to successfully develop and implement engineered systems. Such expertise typically does not come through

  11. 77 FR 14462 - Research, Engineering and Development Advisory Committee

    Science.gov (United States)

    2012-03-09

    ... DEPARTMENT OF TRANSPORTATION Federal Aviation Administration Research, Engineering and Development....S.C. App. 2), notice is hereby given of a meeting of the FAA Research, Engineering and Development.... Name: Research, Engineering & Development Advisory Committee. Time and Date: April 18, 2012--9:30 a.m...

  12. 77 FR 54648 - Research, Engineering and Development Advisory Committee

    Science.gov (United States)

    2012-09-05

    ... DEPARTMENT OF TRANSPORTATION Federal Aviation Administration Research, Engineering and Development....S.C. App. 2), notice is hereby given of a meeting of the FAA Research, Engineering and Development...: Research, Engineering & Development Advisory Committee. TIME AND DATE: September 26, 2012--9 a.m. to 4 p.m...

  13. 76 FR 12404 - Research, Engineering and Development Advisory Committee

    Science.gov (United States)

    2011-03-07

    ... DEPARTMENT OF TRANSPORTATION Federal Aviation Administration Research, Engineering and Development....S.C. App. 2), notice is hereby given of a meeting of the FAA Research, Engineering and Development...: Research, Engineering & Development Advisory Committee. Time and Date: April 20, 2011--9:30 a.m. to 4 p.m...

  14. 75 FR 14243 - Research, Engineering And Development Advisory Committee

    Science.gov (United States)

    2010-03-24

    ... DEPARTMENT OF TRANSPORTATION Federal Aviation Administration Research, Engineering And Development....S.C. App. 2), notice is hereby given of a meeting of the FAA Research, Engineering and Development...: Research, Engineering & Development Advisory Committee. Time and Date: April 21, 2010--9 a.m. to 5 p.m...

  15. 76 FR 44648 - Research, Engineering and Development Advisory Committee

    Science.gov (United States)

    2011-07-26

    ... DEPARTMENT OF TRANSPORTATION Federal Aviation Administration Research, Engineering and Development....S.C. App. 2), notice is hereby given of a meeting of the FAA Research, Engineering and Development.... Name: Research, Engineering & Development Advisory Committee. Time and Date: September 21, 2011--9 a.m...

  16. 78 FR 16357 - Research, Engineering and Development Advisory Committee

    Science.gov (United States)

    2013-03-14

    ... DEPARTMENT OF TRANSPORTATION Federal Aviation Administration Research, Engineering and Development... hereby given of a meeting of the FAA Research, Engineering and Development (R,E&D) Advisory Committee. Name: Research, Engineering & Development Advisory Committee. Time and Date: April 24--8:30 a.m. to 4...

  17. Arnold Rüütel: Eesti riigipead peaks valima rahvas või valijamehed / Arnold Rüütel ; intervjueerinud Tuuli Koch, Ingvar Bärenklau

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2006-01-01

    Ilmunud ka: Postimees : na russkom jazõke (2006) 14. sept., lk. 4-5; Virumaa Teataja (2006) 20. sept., lk. 6, pealk.: Arnold Rüütel presidendivalimisi Riigikogule ei usaldaks, lüh. President Arnold Rüütel pooldab presidendi otsevalimist või ilma Riigikogu vooruta kohe valimiskogus, tutvustab oma valimisplatvormi, räägib oma tervisest ja presidendiametist. Vt. samas: Rüütel: üks aasta selles neetud keskkomitee sekretäri ametis

  18. Juubilar Arnold Rüütel soovib Eestisse vähem vaesust ja kiuslikkust / Arnold Rüütel ; interv. Agnes Kuus

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2008-01-01

    Ilmunud ka: Postimees : na russkom jazõke 12. mai lk. 5. Intervjuu president Arnold Rüütliga tema 80. sünnipäeva puhul, milles juubilar meenutab pingelisi aegu seoses Eesti iseseisvumisega. Vt. samas: Arnold Rüütel 80; President Toomas Hendrik Ilves hindab Rüütli tasakaalukust. President T. H. Ilvese sõnul aitas president Rüütel tuua Euroopat Eestimaale lähemale

  19. Heat engine development for solar thermal power systems

    Science.gov (United States)

    Pham, H. Q.; Jaffe, L. D.

    The parabolic dish solar collector systems for converting sunlight to electrical power through a heat engine will, require a small heat engine of high performance long lifetime to be competitive with conventional power systems. The most promising engine candidates are Stirling, high temperature Brayton, and combined cycle. Engines available in the current market today do not meet these requirements. The development of Stirling and high temperature Brayton for automotive applications was studied which utilizes much of the technology developed in this automotive program for solar power engines. The technical status of the engine candidates is reviewed and the components that may additional development to meet solar thermal system requirements are identified.

  20. Developing a New Industrial Engineering Curriculum Using a Systems Engineering Approach

    Science.gov (United States)

    Buyurgan, Nebil; Kiassat, Corey

    2017-01-01

    This paper reports on the development of an engineering curriculum for a new industrial engineering programme at a medium-sized private university in the northeast United States. A systems engineering process has been followed to design and develop the new curriculum. Considering the programme curriculum as a system, first the stakeholders have…

  1. Development of ergonomic website for engineering education

    Directory of Open Access Journals (Sweden)

    Faradilla Arnes

    2018-01-01

    Full Text Available Engineering education contains two aspects; theory and practice. Practice activity supports the students to implement the theory obtained in the class. Therefore, it will be better if the theory has material visualization in order to support and make easier the student and lecturer in teaching activity. Analisis Perancangan Kerja dan Ergonomi (APK & E is one of the laboratories in Industrial Engineering, Universitas Islam Indonesia. APK & E laboratory which uses website as a tool to communicate to the students. Currently, the existing website still show standard display by conventional way. Based on the questionnaire, the student difficult to understand the material especially for Micromotion Study since this material requires the video to show the student in assembly activity. Augmented Reality (AR combines the real and virtual objects that interactive in the real time and registered in 3D space. AR also combines the real and virtual in displaying information in the real time, in a way that enhances the individual abilities to operate the system in the real world. The system which combines between AR and Micromotion Study was come up. The required software to develop the online AR system is FLARToolKit 2.5.1. In this research, marker detection accuracy measurement of the used toolkit has been conducted and it showed 85% of accuracy level.

  2. Educating the Engineer for Sustainable Community Development

    Science.gov (United States)

    Munoz, D. R.

    2008-12-01

    More than ever before, we are confronting the challenges of limited resources (water, food, energy and mineral), while also facing complex challenges with the environment and related social unrest. Resource access problems are exacerbated by multi-scale geopolitical instability. We seek a balance that will allow profit but also leave a world fit for our children to inherit. Many are working with small groups to make positive change through finding solutions that address these challenges. In fact, some say that in sum, it is the largest human movement that has ever existed. In this talk I will share our experiences to alleviate vulnerabilities for populations of humans in need while working with students, corporate entities and non governmental organizations. Our main focus is to educate a new cadre of engineers that have an enhanced awareness of and better communication skills for a different cultural environment than the one in which they were raised and are hungry to seek new opportunities to serve humanity at a basic level. The results of a few of the more than forty humanitarian engineering projects completed since 2003 will be superimposed on a theoretical framework for sustainable community development. This will be useful information to those seeking a social corporate position of responsibility and a world that more closely approaches a sustainable equilibrium.

  3. Some developing concepts of engineering education

    Science.gov (United States)

    Perkins, C. D.

    1975-01-01

    An analysis of the circumstances which have created a shortage of aeronautical engineering undergraduate students in the universities is presented. Suggestions for motivating students to enter aeronautical engineering are examined. The support of the aeronautical industry for graduate education funding is recommended. Examples of actions taken by governmental agencies to promote increased interest in aeronautical engineering are included.

  4. Bildung and identity development in engineering education

    DEFF Research Database (Denmark)

    Du, Xiangyun

    2006-01-01

    a social context. The analysis of empirical data shows that studying engineering involves not only the mastery of scientific knowledge and technical skills, but also learning the language, established practices, beliefs, values, and norms in the engineering culture, and learning to become an engineer...

  5. 78 FR 47049 - Research, Engineering and Development Advisory Committee

    Science.gov (United States)

    2013-08-02

    ... DEPARTMENT OF TRANSPORTATION Federal Aviation Administration Research, Engineering and Development...; 5 U.S.C. App. 2), notice is hereby given of a meeting of the FAA Research, Engineering and.... Name: Research, Engineering & Development Advisory Committee. Time and Date: September 18--8:30 a.m. to...

  6. Developing Project Duration Models in Software Engineering

    Institute of Scientific and Technical Information of China (English)

    Pierre Bourque; Serge Oligny; Alain Abran; Bertrand Fournier

    2007-01-01

    Based on the empirical analysis of data contained in the International Software Benchmarking Standards Group(ISBSG) repository, this paper presents software engineering project duration models based on project effort. Duration models are built for the entire dataset and for subsets of projects developed for personal computer, mid-range and mainframeplatforms. Duration models are also constructed for projects requiring fewer than 400 person-hours of effort and for projectsre quiring more than 400 person-hours of effort. The usefulness of adding the maximum number of assigned resources as asecond independent variable to explain duration is also analyzed. The opportunity to build duration models directly fromproject functional size in function points is investigated as well.

  7. Developing engineering processes through integrated modelling of product and process

    DEFF Research Database (Denmark)

    Nielsen, Jeppe Bjerrum; Hvam, Lars

    2012-01-01

    This article aims at developing an operational tool for integrated modelling of product assortments and engineering processes in companies making customer specific products. Integrating a product model in the design of engineering processes will provide a deeper understanding of the engineering...... activities as well as insight into how product features affect the engineering processes. The article suggests possible ways of integrating models of products with models of engineering processes. The models have been tested and further developed in an action research study carried out in collaboration...... with a major international engineering company....

  8. Development of an Intelligent Car Engine Fault Troubleshooting ...

    African Journals Online (AJOL)

    Development of an Intelligent Car Engine Fault Troubleshooting System (CEFTS) ... and also provides a troubleshooting framework for other researchers to work on. Keywords: ... inference engine, knowledge acquisition, artificial intelligence.

  9. Math Description Engine Software Development Kit

    Science.gov (United States)

    Shelton, Robert O.; Smith, Stephanie L.; Dexter, Dan E.; Hodgson, Terry R.

    2010-01-01

    The Math Description Engine Software Development Kit (MDE SDK) can be used by software developers to make computer-rendered graphs more accessible to blind and visually-impaired users. The MDE SDK generates alternative graph descriptions in two forms: textual descriptions and non-verbal sound renderings, or sonification. It also enables display of an animated trace of a graph sonification on a visual graph component, with color and line-thickness options for users having low vision or color-related impairments. A set of accessible graphical user interface widgets is provided for operation by end users and for control of accessible graph displays. Version 1.0 of the MDE SDK generates text descriptions for 2D graphs commonly seen in math and science curriculum (and practice). The mathematically rich text descriptions can also serve as a virtual math and science assistant for blind and sighted users, making graphs more accessible for everyone. The MDE SDK has a simple application programming interface (API) that makes it easy for programmers and Web-site developers to make graphs accessible with just a few lines of code. The source code is written in Java for cross-platform compatibility and to take advantage of Java s built-in support for building accessible software application interfaces. Compiled-library and NASA Open Source versions are available with API documentation and Programmer s Guide at http:/ / prim e.jsc.n asa. gov.

  10. Collaborative Engineering for Research and Development

    Science.gov (United States)

    Davis, Jose M.; Keys, L. Ken; Chen, Injazz J.

    2004-01-01

    Research and development (R&D) organizations are being required to be relevant, to be more application-oriented, and to be partners in the strategic management of the business while meeting the same challenges as the rest of the organization, namely: (1) reduced time to market; (2) reduced cost; (3) improved quality; (4) increased reliability; and (5) increased focus on customer needs. Recent advances in computer technology and the Internet have created a new paradigm of collaborative engineering or collaborative product development (CPD), from which new types of relationships among researchers and their partners have emerged. Research into the applicability and benefits of CPD in a low/no production, R&D, and/or government environment is limited. In addition, the supply chain management (SCM) aspects of these relationships have not been studied. This paper presents research conducted at the NASA Glenn Research Center (GRC) investigating the applicability of CPD and SCM in an R&D organization. The study concentrates on the management and implementation of space research activities at GRC. Results indicate that although the organization is engaged in collaborative relationships that incorporate aspects of SCM, a number of areas, such as development of trust and information sharing merit special attention.

  11. Rapid product development: project engineering joined to design engineering in a concurrent engineering context

    Science.gov (United States)

    Bernard, Alain; Ouazzani, A.; Chambolle, F.; Bocquet, Jean Claud

    1997-01-01

    Software tools for designers are mainly based on geometry. Today, many industrial modelers have been rebuilt with C++, or any other object oriented language. This paper proposes to locate the research topics, in order to develop a functional link between project management tools, technical data management and product models. The 'design process' aspect will also be justified through the need of capitalizing designer intent and design history. This is related to different research works of Mechanical Engineering and Logistics Laboratory of Ecole Centrale Paris, and especially two PhD topics.

  12. Engineering Research, Development and Technology, FY95: Thrust area report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-02-01

    The mission of the Engineering Research, Development, and Technology Program at Lawrence Livermore National Laboratory (LLNL) is to develop the knowledge base, process technologies, specialized equipment, tools and facilities to support current and future LLNL programs. Engineering`s efforts are guided by a strategy that results in dual benefit: first, in support of Department of Energy missions, such as national security through nuclear deterrence; and second, in enhancing the nation`s economic competitiveness through their collaboration with US industry in pursuit of the most cost-effective engineering solutions to LLNL programs. To accomplish this mission, the Engineering Research, Development, and Technology Program has two important goals: (1) identify key technologies relevant to LLNL programs where they can establish unique competencies, and (2) conduct high-quality research and development to enhance their capabilities and establish themselves as the world leaders in these technologies. To focus Engineering`s efforts, technology thrust areas are identified and technical leaders are selected for each area. The thrust areas are comprised of integrated engineering activities, staffed by personnel from the nine electronics and mechanical engineering divisions, and from other LLNL organizations. This annual report, organized by thrust area, describes Engineering`s activities for fiscal year 1995. The report provides timely summaries of objectives methods, and key results from eight thrust areas: computational electronics and electromagnetics; computational mechanics; microtechnology; manufacturing technology; materials science and engineering; power conversion technologies; nondestructive evaluation; and information engineering.

  13. Engineering education in Bangladesh - an indicator of economic development

    Science.gov (United States)

    Chowdhury, Harun; Alam, Firoz

    2012-05-01

    Developing nations including Bangladesh are significantly lagging behind the millennium development target due to the lack of science, technology and engineering education. Bangladesh as a least developing country has only 44 engineers per million people. Its technological education and gross domestic product growth are not collinear. Although limited progress was made in humanities, basic sciences, agriculture and medical sciences, a vast gap is left in technical and engineering education. This paper describes the present condition of engineering education in the country and explores ways to improve engineering education in order to meet the national as well as global skills demand.

  14. Cummins Engine Company B5.9 Propane Engine Development, Certification, and Demonstration Project

    Energy Technology Data Exchange (ETDEWEB)

    The ADEPT Group, Inc. (Los Angeles, California)

    1998-12-18

    The objective of this project was to successfuly develop and certify an LPG-dedicated medium-duty original equipment manufacturer (OEM) engine that could be put into production. The engine was launched into production in 1994, and more than 800 B5.9G engines are now in service in the United States and abroad. This engine is now offered by more than 30 bus and truck OEMs.

  15. Kõrgeid ja inimlikke sihte / Arnold Rüütel

    Index Scriptorium Estoniae

    Rüütel, Arnold

    2006-01-01

    President Arnold Rüütli uusaastaläkitus. Ilmunud ka Postimees : na russkom jazõke (2006/Jan/3) lk. 7 ; Pärnu Postimees (2006/Jan/3) lk. 11 ; Virumaa Teataja (2006/Jan/3) lk. 7 ; Järva Teataja (2006/Jan/3) lk. 2 ; Võrumaa Teataja (2006/Jan/3) lk. 2 ; Põhjarannik (2006/Jan/3) lk. 2 ; Severnoje Poberezhje (2006/Jan/3) lk. 2 ; Meie Maa (2006/Jan/3) lk. 2 ; Hiiu Leht (2006/Jan/3) lk. 2; Eesti Päevaleht, lüh. (2006/Jan/3) lk. 3; Maaleht (2006/Jan/5) lk. 6 ; Lääne-Harju Ekspress (2006/Jan/7) lk. 3; Vaba Eesti Sõna = Free Estonian Word, 2006/Jan/5, lk. 2

  16. Agile Service Development: A Rule-Based Method Engineering Approach

    NARCIS (Netherlands)

    dr. Martijn Zoet; Stijn Hoppenbrouwers; Inge van de Weerd; Johan Versendaal

    2011-01-01

    Agile software development has evolved into an increasingly mature software development approach and has been applied successfully in many software vendors’ development departments. In this position paper, we address the broader agile service development. Based on method engineering principles we

  17. A Summer Leadership Development Program for Chemical Engineering Students

    Science.gov (United States)

    Simpson, Annie E.; Evans, Greg J.; Reeve, Doug

    2012-01-01

    The Engineering Leaders of Tomorrow Program (LOT) is a comprehensive curricular, co-curricular, extra-curricular leadership development initiative for engineering students. LOT envisions: "an engineering education that is a life-long foundation for transformational leaders and outstanding citizens." Academic courses, co-curricular certificate…

  18. Condition and prospects of development of agricultural mechanical engineering

    OpenAIRE

    Vsevolod Babushkin; Margarita Ignatyeva

    2011-01-01

    In this paper, an estimation of condition and level of development of agricultural mechanical engineering is given; also an expert estimation of scales of the Russian market of agricultural machinery is given. The factors negatively influencing formation of the named market are designated. Features and prospects of development of agricultural mechanical engineering of Sverdlovsk region are defined. State regulation mechanisms of domestic agricultural mechanical engineering development are des...

  19. Engineering, Development and Philosophy American, Chinese and European Perspectives

    CERN Document Server

    Mitcham, Carl; Li, Bocong; An, Yanming

    2012-01-01

    This inclusive, cross-cultural study rethinks the nexus between engineering, development, and culture. It offers diverse commentary from a range of disciplinary perspectives on how the philosophies of today’s cultural triumvirate—American, European and Chinese—are shaped and given nuance by the cross-fertilization of engineering and development. Scholars from the humanities and social sciences as well as engineers themselves reflect on key questions that arise in this relational context, such as how international development work affects the professional views, identities, practice and ethics of engineers.   The first volume to offer a systematic and collaborative study that cuts across continental boundaries, the book delineates the kinds of skills and competences that tomorrow’s engineering success stories will require, and analyzes fascinating aspects of the interplay between engineering and philosophy, such as how traditionally Chinese ways of thinking can influence modern engineering practice in...

  20. New trends in nuclear power engineering development

    International Nuclear Information System (INIS)

    Krasin, A.K.

    1974-01-01

    The specific features are considered of three designs of nuclear power plants with fast reactors: three-circuit nuclear power plant with liquid sodium as primary and secondary coolant, in the third circuit water vapor being used as turbine working medium, dual cycle nuclear power plant with pressurized helium as primary coolant and water vapor as turbine working medium, direct cycle nuclear power plant with a dissociating gas (nitrogen tetroxide N 2 O 4 ) as reactor coolant and turbine working medium. The version of the direct cycle nuclear power plant with dissociating N 2 O 4 was proposed and being developed by the Institute of Nuclear Engineering of the Academy of Sciencies of the BSSR. The thermal and physical properties of the dissociating gas allow a high-power-density reactor core to be used with a hard neutron spectra resulting in a high breeding ratio and a short doubling time. The pressure range from 150 to 170 bar was proven for this coolant under laboratory conditions and structural materials were chosen that ensure all the components of the direct cycle nuclear power plant to be workable. At present it is difficult to say which of the three versions is the most advantageous. The further development of a full-scale prototypes of a commercial nuclear power plant with a fast reactor and investigation of their technical and economic parameters remain the problems of utmost importance. A possible use of nuclear reactors is shortly considered for process heat production, in ferrous metallurgy, for hydrogen and new isotope production, and for radiation chemistry as well

  1. Engineer Research and Development Center's Materials Testing Center (MTC)

    Data.gov (United States)

    Federal Laboratory Consortium — The Engineer Research and Development Center's Materials Testing Center (MTC) is committed to quality testing and inspection services that are delivered on time and...

  2. Supporting Usability Engineering in Small Software Development Organizations

    DEFF Research Database (Denmark)

    Bornoe, Nis; Stage, Jan

    2013-01-01

    Despite an interest and use of different usability engineering methods small software development organizations find it challenging to implement usability engineering into the software development process. We present the results from a study about usability engineering in practice. Through a series...... of semistructured interviews we want to get an understanding of how usability is implemented into the organizations and how it’s practiced in reality. We found that the developers found it problematic to combine agile software development methods with classic usability engineering methods. A lack of solid usability...... engineering expertise and not least experience seems to be a main obstacle for a successful implementation of usability engineering into current software development practices. They are requesting methods and procedures that fit better with their current practices and strategies to implement usability...

  3. Evaluation of environmental data relating to selected nuclear power plant sites. The Duane Arnold Energy Center site

    International Nuclear Information System (INIS)

    Vaslow, F.; Murarka, I.P.

    1976-08-01

    Analyses were made on 1974-1975 data pertaining to water quality and the use of biocides at the Duane Arnold Energy Center, which began operating in February 1975. The analyses showed no immediate deleterious effects due to plant operations. Although the plant has not been in operation long enough to reveal any long-term deleterious effects, present indications do not lead to a concerned prediction that any are developing. The data utilized, the methods of analysis, and the results obtained are presented in detail along with recommendations for improving the current monitoring techniques

  4. Microbial Development and Metabolic Engineering | Bioenergy | NREL

    Science.gov (United States)

    Diversity Our genetically engineered microbes utilize a variety of feedstock including cellulose, xylan , syngas, simple sugars, organic acids, and carbon dioxide (CO2). We have modified the metabolic pathways

  5. Engineering Education in Bangladesh--An Indicator of Economic Development

    Science.gov (United States)

    Chowdhury, Harun; Alam, Firoz

    2012-01-01

    Developing nations including Bangladesh are significantly lagging behind the millennium development target due to the lack of science, technology and engineering education. Bangladesh as a least developing country has only 44 engineers per million people. Its technological education and gross domestic product growth are not collinear. Although…

  6. Further developments in performance prediction techniques of adiabatic diesel engines

    Energy Technology Data Exchange (ETDEWEB)

    Rasihhan, Y

    1990-01-01

    The engine cycle simulation program 'SPICE', developed at Bath University, has been used extensively for insulated diesel engine research. The present study introduces more comprehensive engine heat transfer models thus enabling us to study the insulated engine heat transfer and performance characteristics in more detail. The new version of 'SPICE' separates the gas to wall heat transfer into two parts, convective and radiative. For this purpose, a detailed radiative heat transfer model which considers both the flame (gas and soot) and wall to wall radiative heat transfer is written. The previous engine resistance model is refined and replaced by a more detailed resistance model which considers piston-liner conduction heat transfer and 2-D heat flow in the liner. The wall surface temperature swing is also included in the engine heat transfer calculations which is quite significant in low conductivity ceramic insulated engines. A 1-D finite difference model is written for the transient heat transfer region of the wall and linked to the engine resistance model. This new version of 'SPICE' is used to predict the insulated engine heat transfer and performance for the experimental Petter PH1W engine for various insulation levels and schemes. An answer to the controversy of increase in engine heat loss with insulation is looked for. The effect of wall deposits on engine heat transfer and its significance for the insulated engine is highlighted. (Author).

  7. Engineering Knowledge and Student Development: An Institutional and Pedagogical Critique of Engineering Education

    Science.gov (United States)

    Tang, Xiaofeng

    Educators have recommended the integration of engineering and the liberal arts as a promising educational model to prepare young engineers for global economic, environmental, sociotechnical, and ethical challenges. Drawing upon philosophy of technology, engineering studies, and educational psychology, this dissertation examines diverse visions and strategies for integrating engineering and liberal education and explores their impacts on students' intellectual and moral development. Based on archival research, interviews, and participant observation, the dissertation presents in-depth case studies of three educational initiatives that seek to blend engineering with the humanities, social sciences, and arts: Harvey Mudd College, the Picker Engineering Program at Smith College, and the Programs in Design and Innovation at Rensselaer Polytechnic Institute. The research finds that learning engineering in a liberal arts context increases students' sense of "owning" their education and contributes to their communication, teamwork, and other non-technical professional skills. In addition, opportunities for extensive liberal arts learning in the three cases encourage some students to pursue alternative, less technocentric approaches to engineering. Nevertheless, the case studies suggest that the epistemological differences between the engineering and liberal arts instructors help maintain a technical/social dualism among most students. Furthermore, the dissertation argues a "hidden curriculum," which reinforces the dominant ideology in the engineering profession, persists in the integrated programs and prevents the students from reflecting on the broad social context of engineering and critically examining the assumptions upheld in the engineering profession.

  8. Arnold Rüütel rikkus betoonpaneelidest kai ehitamisega seadust / Oliver Rand

    Index Scriptorium Estoniae

    Rand, Oliver, 1971-

    2007-01-01

    Laimjala vallas Saarekülas president Arnold Rüütli omavolilist ehitustegevust kontrollimas käinud keskkonnainspektorid leidsid, et paadisilla rajamiseks oleks president pidanud taotlema erikasutusluba. Ilmunud ka: Meie Maa (2007) 24. aug. 2007, lk. 1

  9. Olulisim interdistsiplinaarne sündmus anno domini 2004? / Arnold Rüütel

    Index Scriptorium Estoniae

    Rüütel, Arnold

    2004-01-01

    President Arnold Rüütel, kultuuriminister Urmas Paet, Tallinna linnapea Tõnis Palts ja Tartu linnapea Laine Jänes vastavad ajalehe Postimees küsimusele mööduva aasta interdistsiplinaarsematest kultuurisündmustest

  10. Positive semidefinite matrix completion, universal rigidity and the Strong Arnold Property

    NARCIS (Netherlands)

    M. Laurent (Monique); A. Varvitsiotis (Antonios)

    2014-01-01

    htmlabstractThis paper addresses the following three topics: positive semidefinite (psd) matrix completions, universal rigidity of frameworks, and the Strong Arnold Property (SAP). We show some strong connections among these topics, using semidefinite programming as unifying theme. Our main

  11. Arnold Rüütel saab kõrgeima autasu / Silja Lättemäe

    Index Scriptorium Estoniae

    Lättemäe, Silja, 1952-

    2008-01-01

    President Arnold Rüütel saab president Toomas Hendrik Ilveselt Riigivapi ketiklassi teenetemärgi. Rahvaliit pole rahul, et A. Rüütel pole saanud ühtki riiklikku autasu oma panuse eest Eesti taasiseseisvumisse

  12. Presidendi kantselei tellis Arnold Rüütli büsti / Kadri Paas

    Index Scriptorium Estoniae

    Paas, Kadri, 1982-

    2007-01-01

    Presidendi kantselei sõlmis kunstnik Endel Tanilooga 31. oktoobril 2007 lepingu president Arnold Rüütli pronksbüsti tegemiseks. Kuju valmib 2008. a. jaanuaris ja paigutatakse tulevikus kantselei roosiaeda

  13. Arnold Sommerfeld. Atomic physicist and messenger of culture 1868-1951. A biography; Arnold Sommerfeld. Atomphysiker und Kulturbote 1868-1951. Eine Biografie

    Energy Technology Data Exchange (ETDEWEB)

    Eckert, Michael

    2013-09-01

    Arnold Sommerfeld is beside Albert Einstein, Niels Bohr, and Max Planck one of the founders of modern atomic and quantum theory. His career began in the 1890th years at the University of Goettingen, the world center of mathematics of that time. Since 1906 he created on the professorship for theoretical physics at the Munich university one of the most important schools of science, the students of which are well-known theorists of the atomic era like as the Nobel-price winners Hans Bethe, Peter Debye, Wolfgang Pauli, and Werner Heisenberg. He also developed far beyond his subject an unprecedented impact. He travelled as ''messenger of culture'' in many countries in order to advertise in the years after the first world war for the reputation of Germany as culture nation. By the nationalsocialism the Munich ''nursery of theoretical physics'' however was prepared an inglorious end, because Sommerfeld counted for a ''main propagandist of Jewish theories''. By the example of this life of a physicist also the eventful history of a whole subject.

  14. Development cooperation as methodology for teaching social responsibility to engineers

    Science.gov (United States)

    Lappalainen, Pia

    2011-12-01

    The role of engineering in promoting global well-being has become accentuated, turning the engineering curriculum into a means of dividing well-being equally. The gradual fortifying calls for humanitarian engineering have resulted in the incorporation of social responsibility themes in the university curriculum. Cooperation, communication, teamwork, intercultural cooperation, sustainability, social and global responsibility represent the socio-cultural dimensions that are becoming increasingly important as globalisation intensifies the demands for socially and globally adept engineering communities. This article describes an experiment, the Development Cooperation Project, which was conducted at Aalto University in Finland to integrate social responsibility themes into higher engineering education.

  15. Difficult intubation in a parturient with syringomyelia and Arnold-Chiari malformation: Use of Airtraq™ laryngoscope

    Directory of Open Access Journals (Sweden)

    Bensghir Mustapha

    2011-01-01

    Full Text Available Anesthetic technique in parturient with syringomyelia and Arnold-Chiari malformation is variable depending on the teams. Difficult intubation is one of the risks when general anesthesia is opted. Different devices have been used to manage the difficult intubation in pregnant women. We report the use of Airtraq™ laryngoscope after failed standard laryngoscopy in a parturient with syringomyelia and Arnold-Chiari type I malformation.

  16. President Arnold Rüütel tahab anda noortele peredele maad / Mati Määrits

    Index Scriptorium Estoniae

    Määrits, Mati, 1958-

    2005-01-01

    Põlvamaa omavalitsusjuhid avaldasid toetust president Arnold Rüütli ettepanekule anda maad eelkõige noortele peredele. Presidendi juuresolekul ei leitud aga üksmeelt haridusinvesteeringute jaotamises laste arvust lähtudes. President Arnold Rüütel vastab küsimusele, kas kaks päeva Põlvamaal suutsid teda millegagi üllatada. Maakonnavisiit Põlvamaale 08.-09.06.2005

  17. Comparing Two Approaches for Engineering Education Development

    DEFF Research Database (Denmark)

    Edström, Kristina; Kolmos, Anette

    2012-01-01

    During the last decade there have been two dominating models for reforming engineering education: Problem/Project Based Learning (PBL) and the CDIO Initiative. The aim of this paper is to compare the PBL and CDIO approaches to engineering education reform, to identify and explain similarities...... and differences. CDIO and PBL will each be defined and compared in terms of the original need analysis, underlying educational philosophy and the essentials of the respective approaches to engineering education. In these respects we see many similarities. Circumstances that explain differences in history...... approaches have much in common and can be combined, and especially that the practitioners have much to learn from each other’s experiences through a dialogue between the communities. This structured comparison will potentially indicate specifically what an institution experienced in one of the communities...

  18. Who will save the tokamak - Harry Potter, Arnold Schwarzenegger, or Shaquille O'Neil?

    Science.gov (United States)

    Freidberg, J.; Mangiarotti, F.; Minervini, J.

    2014-10-01

    The tokamak is the current leading contender for a fusion power reactor. The reason for the preeminence of the tokamak is its high quality plasma physics performance relative to other concepts. Even so, it is well known that the tokamak must still overcome two basic physics challenges before becoming viable as a DEMO and ultimately a reactor: (1) the achievement of non-inductive steady state operation, and (2) the achievement of robust disruption free operation. These are in addition to the PMI problems faced by all concepts. The work presented here demonstrates by means of a simple but highly credible analytic calculation that a ``standard'' tokamak cannot lead to a reactor - it is just not possible to simultaneously satisfy all the plasma physics plus engineering constraints. Three possible solutions, some more well-known than others, to the problem are analyzed. These visual image generating solutions are defined as (1) the Harry Potter solution, (2) the Arnold Schwarzenegger solution, and (3) the Shaquille O'Neil solution. Each solution will be described both qualitatively and quantitatively at the meeting.

  19. Comparison of Engine Simulation Software for Development of Control System

    Directory of Open Access Journals (Sweden)

    KinYip Chan

    2013-01-01

    Full Text Available Most commonly used commercial engine simulation packages generate detailed estimation of the combustion and gas flow parameters. These parameters are required for advanced research on fluid flow and heat transfer and development of geometries of engine components. However, engine control involves different operating parameters. Various sensors are installed into the engine, the combustion performance is recorded, and data is sent to engine control unit (ECU. ECU computes the new set of parameters to make fine adjustments to actuators providing better engine performance. Such techniques include variable valve timing, variable ignition timing, variable air to fuel ratio, and variable compression ratio. In the present study, two of the commercial packages, Ricardo Wave and Lotus Engine Simulation, have been tested on the capabilities for engine control purposes. These packages are compared with an in-house developed package and with reference results available from the literature. Different numerical experiments have been carried out from which it can be concluded that all packages predict similar profiles of pressure and temperature in the engine cylinder. Moreover, those are in reasonable agreement with the reference results while in-house developed package is possible to run simulations with changing speed for engine control purpose.

  20. Thrust Area Report, Engineering Research, Development and Technology

    Energy Technology Data Exchange (ETDEWEB)

    Langland, R. T.

    1997-02-01

    The mission of the Engineering Research, Development, and Technology Program at Lawrence Livermore National Laboratory (LLNL) is to develop the knowledge base, process technologies, specialized equipment, tools and facilities to support current and future LLNL programs. Engineering`s efforts are guided by a strategy that results in dual benefit: first, in support of Department of Energy missions, such as national security through nuclear deterrence; and second, in enhancing the nation`s economic competitiveness through our collaboration with U.S. industry in pursuit of the most cost- effective engineering solutions to LLNL programs. To accomplish this mission, the Engineering Research, Development, and Technology Program has two important goals: (1) identify key technologies relevant to LLNL programs where we can establish unique competencies, and (2) conduct high-quality research and development to enhance our capabilities and establish ourselves as the world leaders in these technologies. To focus Engineering`s efforts technology {ital thrust areas} are identified and technical leaders are selected for each area. The thrust areas are comprised of integrated engineering activities, staffed by personnel from the nine electronics and mechanical engineering divisions, and from other LLNL organizations. This annual report, organized by thrust area, describes Engineering`s activities for fiscal year 1996. The report provides timely summaries of objectives, methods, and key results from eight thrust areas: Computational Electronics and Electromagnetics; Computational Mechanics; Microtechnology; Manufacturing Technology; Materials Science and Engineering; Power Conversion Technologies; Nondestructive Evaluation; and Information Engineering. Readers desiring more information are encouraged to contact the individual thrust area leaders or authors. 198 refs., 206 figs., 16 tabs.

  1. Development of interdisciplinary undergraduate railroad engineering course.

    Science.gov (United States)

    2016-02-29

    Professor James McKinney was a participant in the AREMA 2008 Railroad Engineering Education Symposium (REES) held at the University of Illinois at Urbana-Champaign, as well as the AREMA 2010 REES held at the Johnson County Community College/BNSF's Tr...

  2. Development Activities on Airbreathing Combined Cycle Engines

    Science.gov (United States)

    McArthur, J. Craig; Lyles, Garry (Technical Monitor)

    2000-01-01

    Contents include the following: Advanced reusable transportation(ART); aerojet and rocketdyne tests, RBCC focused concept flowpaths,fabricate flight weigh, test select components, document ART project, Istar (Integrated system test of an airbreathing rocket); combined cycle propulsion testbed;hydrocarbon demonstrator tracebility; Istar engine system and vehicle system closure study; and Istar project planning.

  3. Systems Engineering Assessment & Workforce Development Plan

    Science.gov (United States)

    2012-11-05

    Government or its technical domains. Other fields, such as culinary and healthcare, have also identified these emerging and growing issues (Calhoun...et al. (2009). "The Art and Science of Systems Engineering." Systems Research Forum 3(2): 81-100. Shenhar, A. and B. Sauser, Eds. (2009). Systems

  4. Development of an Industrial Engineering Project

    Science.gov (United States)

    Moreno, Lorenzo; Gonzalez, Evelio; Acosta, Leopoldo; Toledo, Jonay; Marichal, Nicolas; Hamilton, Alberto; Sigut, Marta; Mendez, J. Albino; Hernandez, Sergio; Torres, Santiago

    2005-01-01

    This paper presents a teaching strategy of the scheduling and developmental phase of an Industrial Engineering computer project. It is based on a real project which has been carried out by our department in collaboration with a local company. The classroom setting provides an environment where students can experience firsthand all phases of the…

  5. Modeling the development of tissue engineered cartilage

    NARCIS (Netherlands)

    Sengers, B.G.

    2005-01-01

    The limited healing capacity of articular cartilage forms a major clinical problem. In general, current treatments of cartilage damage temporarily reliefs symptoms, but fail in the long term. Tissue engineering (TE) has been proposed as a more permanent repair strategy. Cartilage TE aims at

  6. Engineering vascular development for tissue regeneration

    NARCIS (Netherlands)

    Rivron, N.C.

    2010-01-01

    Tissue engineering and regenerative medicine aim at restoring a damaged tissue by recreating in vitro or promoting its regeneratin in vovo. The vasculature is central to these therapies for the irrigation of the defective tissue (oxygen, nutrients or circulating regenerative cells) and as an

  7. An Engineer-To-Order Mass Customization Development Framework

    DEFF Research Database (Denmark)

    Bossen, Jacob; Hansson, Michael Natapon; Madsen, Ole

    2014-01-01

    competitiveness and revenue, in which Engineer-To-Order companies may benefit from adopting Mass Customization concepts. As automated manufacturing systems tends to be software intensive, it become equally important to enable reusability for physical components and for software related artefacts. In parallel...... to Mass Customization, Software Product Line Engineering has emerged as a way for software developers to manage variability and reusability. This paper seeks to combine the concepts of Mass Customization and Software Product Line Engineering, by introducing a development framework applicable for Engineer...

  8. IDC Re-Engineering Phase 3 Development Plan.

    Energy Technology Data Exchange (ETDEWEB)

    Harris, James M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Burns, John F. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Pollock, David L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-01-01

    Sandia National Laboratories has prepared a project development plan that proposes how the parties interested in the IDC Re-Engineering system will coordinate its development, testing and transition to operations.

  9. IDC Re-Engineering Phase 3 Development Plan

    International Nuclear Information System (INIS)

    Harris, James M.; Burns, John F.; Pollock, David L.

    2017-01-01

    Sandia National Laboratories has prepared a project development plan that proposes how the parties interested in the IDC Re-Engineering system will coordinate its development, testing and transition to operations.

  10. Assessing the feasibility of a web-based registry for multiple orphan lung diseases: the Australasian Registry Network for Orphan Lung Disease (ARNOLD) experience

    OpenAIRE

    Casamento, K.; Laverty, A.; Wilsher, M.; Twiss, J.; Gabbay, E.; Glaspole, I.; Jaffe, A.

    2016-01-01

    Background We investigated the feasibility of using an online registry to provide prevalence data for multiple orphan lung diseases in Australia and New Zealand. Methods A web-based registry, The Australasian Registry Network of Orphan Lung Diseases (ARNOLD) was developed based on the existing British Paediatric Orphan Lung Disease Registry. All adult and paediatric respiratory physicians who were members of the Thoracic Society of Australia and New Zealand in Australia and New Zealand were s...

  11. Engineering for Sustainable Development - an Obligatory Skill of the Future Engineer

    DEFF Research Database (Denmark)

    Alting, Leo

    2001-01-01

    , the environmental and the social/societal. The economical responsibility is handled by the well-known and accepted methods/tools/regulations, to handle the environmental responsibility good engineering methods and tools are appearing, but to handle the social/societal responsibility only fragmented and inconsistent...... elements exist. However, one thing is clear - we will have to provide our engineering students with understanding, methods and tools so that they can engineer sustainable solutions - especially engineer environmentally friendlier solutions. The Department of Manufacturing Engineering and the Institute...... for Product Development have actively taken part in the development from awareness of the environmental problems to providing methods and tools to support a sustainable development. The situation today in the education at DTU is shortly mentioned and the education at the Department of Manufacturing...

  12. Photonics education development for electrical engineering students

    Science.gov (United States)

    Cao, Yang; Luo, Yuan; Liu, Yu; Hu, ZhangFang; Cai, Xuemei

    2017-08-01

    We describe the contents of an advanced undergraduate course on photonics at School of Electrical Engineering, Chongqing University of Posts and Telecommunications. The main goal of the course is to equip the student with the necessary theoretical and practical knowledge to participate in photonics-related industry and further graduate level study and research if they choose. The prerequisites include college-level physics and higher mathematics which a general engineering student has already had in his/her first and second year college study. Although applications of photonics are ubiquitous such as telecommunications, photonic computing, spectroscopy, military technology, and biophotonics etc. Telecommunication information system application is more emphasized in our course considering about the potential job chances for our students.

  13. Development of nuclear rocket engine technology

    International Nuclear Information System (INIS)

    Gunn, S.V.

    1989-01-01

    Research sponsored by the Atomic Energy Commission, the USAF, and NASA (later on) in the area of nuclear rocket propulsion is discussed. It was found that a graphite reactor, loaded with highly concentrated Uranium 235, can be used to heat high pressure liquid hydrogen to temperatures of about 4500 R, and to expand the hydrogen through a high expansion ratio rocket nozzle assembly. The results of 20 reactor tests conducted at the Nevada Test Site between July 1959 and June 1969 are analyzed. On the basis of these results, the feasibility of solid graphite reactor/nuclear rocket engines is revealed. It is maintained that this technology will support future space propulsion requirements, using liquid hydrogen as the propellant, for thrust requirements ranging from 25,000 lbs to 250,000 lbs, with vacuum specific impulses of at least 850 sec and with full engine throttle capability. 12 refs

  14. The Systems Engineering Process for Human Support Technology Development

    Science.gov (United States)

    Jones, Harry

    2005-01-01

    Systems engineering is designing and optimizing systems. This paper reviews the systems engineering process and indicates how it can be applied in the development of advanced human support systems. Systems engineering develops the performance requirements, subsystem specifications, and detailed designs needed to construct a desired system. Systems design is difficult, requiring both art and science and balancing human and technical considerations. The essential systems engineering activity is trading off and compromising between competing objectives such as performance and cost, schedule and risk. Systems engineering is not a complete independent process. It usually supports a system development project. This review emphasizes the NASA project management process as described in NASA Procedural Requirement (NPR) 7120.5B. The process is a top down phased approach that includes the most fundamental activities of systems engineering - requirements definition, systems analysis, and design. NPR 7120.5B also requires projects to perform the engineering analyses needed to ensure that the system will operate correctly with regard to reliability, safety, risk, cost, and human factors. We review the system development project process, the standard systems engineering design methodology, and some of the specialized systems analysis techniques. We will discuss how they could apply to advanced human support systems development. The purpose of advanced systems development is not directly to supply human space flight hardware, but rather to provide superior candidate systems that will be selected for implementation by future missions. The most direct application of systems engineering is in guiding the development of prototype and flight experiment hardware. However, anticipatory systems engineering of possible future flight systems would be useful in identifying the most promising development projects.

  15. Arnold Rüütel: e-hääletamine tuleb niikuinii / Arnold Rüütel ; intervjueerinud Kai Kalamees

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2005-01-01

    President Arnold Rüütel vastab küsimustele, mis on seotud tema otsusega mitte kuulutada välja e-hääletamist lubavat seadust. Presidendi sõnul ei mõjuta tema otsus kuidagi e-hääletuse tänavust toimumist

  16. President Arnold Rüütel : "Me ei tohi seda teed enam edasi minna" / Arnold Rüütel ; intervjueerinud Harda Roosna

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2006-01-01

    President Arnold Rüütli visiidist Hiiumaale. President vastas küsimustele meditsiini, tööhõive, päästeteenistuse kohta. Vabariigi President Hiiumaal 26.-27.07.2006. Vt. samas: President poebussis ja kirikus

  17. Arnold Rüütel: "Kohati jääb meie erakondadel puudu sisemisest demokraatiast." / Arnold Rüütel ; intervjueerinud Urmo Soonvald

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2004-01-01

    President Arnold Rüütel vastab küsimustele, mis puudutavad vedurijuhtide streiki, noorte arstide lahkumist välismaale, Rahvaliidu saadikurühma tekkimist Tallinna volikogus, Res Publica ja Reformierakonna võimalikku liitumist, Leedu-visiiti

  18. Reverse engineering development: Crosstalk opportunities between developmental biology and tissue engineering.

    Science.gov (United States)

    Marcucio, Ralph S; Qin, Ling; Alsberg, Eben; Boerckel, Joel D

    2017-11-01

    The fields of developmental biology and tissue engineering have been revolutionized in recent years by technological advancements, expanded understanding, and biomaterials design, leading to the emerging paradigm of "developmental" or "biomimetic" tissue engineering. While developmental biology and tissue engineering have long overlapping histories, the fields have largely diverged in recent years at the same time that crosstalk opportunities for mutual benefit are more salient than ever. In this perspective article, we will use musculoskeletal development and tissue engineering as a platform on which to discuss these emerging crosstalk opportunities and will present our opinions on the bright future of these overlapping spheres of influence. The multicellular programs that control musculoskeletal development are rapidly becoming clarified, represented by shifting paradigms in our understanding of cellular function, identity, and lineage specification during development. Simultaneously, advancements in bioartificial matrices that replicate the biochemical, microstructural, and mechanical properties of developing tissues present new tools and approaches for recapitulating development in tissue engineering. Here, we introduce concepts and experimental approaches in musculoskeletal developmental biology and biomaterials design and discuss applications in tissue engineering as well as opportunities for tissue engineering approaches to inform our understanding of fundamental biology. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc. J Orthop Res 35:2356-2368, 2017. © 2017 Orthopaedic Research Society. Published by Wiley Periodicals, Inc.

  19. The Bologna Process, Globalisation and Engineering Education Developments

    Science.gov (United States)

    Uhomoibhi, James O.

    2009-01-01

    Purpose: The purpose of this paper is to report on the Bologna Process in the light of globalisation and examine how it affects curriculum and engineering education developments. Design/methodology/approach: The growing need for creative competitiveness and the striving for specific profiles of engineering qualifications that are of high quality…

  20. Developing a Vision of Pre-College Engineering Education

    Science.gov (United States)

    Marshall, Jill A.; Berland, Leema K.

    2012-01-01

    We report the results of a study focused on identifying and articulating an ''epistemic foundation'' underlying a pre-collegiate focus on engineering. We do so in the context of UTeach"Engineering" (UTE), a program supported in part by funding by the National Science Foundation and designed to develop a model approach to address the…

  1. Developing a system engineering program to improve performance and reliability

    International Nuclear Information System (INIS)

    Keuter, D.

    1985-01-01

    After several maintenance, operational, and equipment problems last year, Trojan set out on a mission to improve plant performance and reliability by strengthening its on-site engineering organization. This paper presents Trojan's plans in developing an on-site system engineering organization

  2. What Do Final Year Engineering Students Know about Sustainable Development?

    Science.gov (United States)

    Nicolaou, I.; Conlon, E.

    2012-01-01

    This paper presents data from a project that aims to determine the level of knowledge and understanding of engineering students about sustainable development (SD). The data derive from a survey completed by final year engineering students in three Irish Higher Education Institutions. This paper is part of a larger study that examines the…

  3. Development of a full scope reactor engineering simulator

    International Nuclear Information System (INIS)

    Venhuizen, J.R.; Laats, E.T.

    1988-01-01

    An engineering laboratory is pursuing the development of an engineering simulator for use by several agencies of the U.S. Government. According to the authors, this simulator will provide the highest fidelity simulation with initial objectives for studying augmented nuclear reactor operator training, and later for advanced concepts testing as applicable to control room accident diagnosis and management

  4. Towards evolution-guided microbial engineering - tools development and applications

    DEFF Research Database (Denmark)

    Genee, Hans Jasper

    is thedevelopment of highly robust biosensor-based synthetic selection systemsthat enable high-throughput functional interrogation of complexphenotypic libraries. Using the model organism Escherichia coli as a host, Ideploy these systems to i) perform metagenome wide sequenceindependentidentification of novel...... for microbial engineering anddemonstrates direct applications to gene discovery, protein engineering andcell factory development....

  5. Developments in REDES: The Rocket Engine Design Expert System

    Science.gov (United States)

    Davidian, Kenneth O.

    1990-01-01

    The Rocket Engine Design Expert System (REDES) was developed at NASA-Lewis to collect, automate, and perpetuate the existing expertise of performing a comprehensive rocket engine analysis and design. Currently, REDES uses the rigorous JANNAF methodology to analyze the performance of the thrust chamber and perform computational studies of liquid rocket engine problems. The following computer codes were included in REDES: a gas properties program named GASP; a nozzle design program named RAO; a regenerative cooling channel performance evaluation code named RTE; and the JANNAF standard liquid rocket engine performance prediction code TDK (including performance evaluation modules ODE, ODK, TDE, TDK, and BLM). Computational analyses are being conducted by REDES to provide solutions to liquid rocket engine thrust chamber problems. REDES was built in the Knowledge Engineering Environment (KEE) expert system shell and runs on a Sun 4/110 computer.

  6. Developing the Next Generation of Science Data System Engineers

    Science.gov (United States)

    Moses, John F.; Behnke, Jeanne; Durachka, Christopher D.

    2016-01-01

    At Goddard, engineers and scientists with a range of experience in science data systems are needed to employ new technologies and develop advances in capabilities for supporting new Earth and Space science research. Engineers with extensive experience in science data, software engineering and computer-information architectures are needed to lead and perform these activities. The increasing types and complexity of instrument data and emerging computer technologies coupled with the current shortage of computer engineers with backgrounds in science has led the need to develop a career path for science data systems engineers and architects.The current career path, in which undergraduate students studying various disciplines such as Computer Engineering or Physical Scientist, generally begins with serving on a development team in any of the disciplines where they can work in depth on existing Goddard data systems or serve with a specific NASA science team. There they begin to understand the data, infuse technologies, and begin to know the architectures of science data systems. From here the typical career involves peermentoring, on-the-job training or graduate level studies in analytics, computational science and applied science and mathematics. At the most senior level, engineers become subject matter experts and system architect experts, leading discipline-specific data centers and large software development projects. They are recognized as a subject matter expert in a science domain, they have project management expertise, lead standards efforts and lead international projects. A long career development remains necessary not only because of the breadth of knowledge required across physical sciences and engineering disciplines, but also because of the diversity of instrument data being developed today both by NASA and international partner agencies and because multidiscipline science and practitioner communities expect to have access to all types of observational data

  7. Developing the Next Generation of Science Data System Engineers

    Science.gov (United States)

    Moses, J. F.; Durachka, C. D.; Behnke, J.

    2015-12-01

    At Goddard, engineers and scientists with a range of experience in science data systems are needed to employ new technologies and develop advances in capabilities for supporting new Earth and Space science research. Engineers with extensive experience in science data, software engineering and computer-information architectures are needed to lead and perform these activities. The increasing types and complexity of instrument data and emerging computer technologies coupled with the current shortage of computer engineers with backgrounds in science has led the need to develop a career path for science data systems engineers and architects. The current career path, in which undergraduate students studying various disciplines such as Computer Engineering or Physical Scientist, generally begins with serving on a development team in any of the disciplines where they can work in depth on existing Goddard data systems or serve with a specific NASA science team. There they begin to understand the data, infuse technologies, and begin to know the architectures of science data systems. From here the typical career involves peer mentoring, on-the-job training or graduate level studies in analytics, computational science and applied science and mathematics. At the most senior level, engineers become subject matter experts and system architect experts, leading discipline-specific data centers and large software development projects. They are recognized as a subject matter expert in a science domain, they have project management expertise, lead standards efforts and lead international projects. A long career development remains necessary not only because of the breath of knowledge required across physical sciences and engineering disciplines, but also because of the diversity of instrument data being developed today both by NASA and international partner agencies and because multi-discipline science and practitioner communities expect to have access to all types of observational

  8. Active Involvement of Software Developers in Usability Engineering

    DEFF Research Database (Denmark)

    Bornoe, Nis; Stage, Jan

    2017-01-01

    The essence of usability evaluations is to produce feedback that supports the downstream utility so the interaction design can be improved and problems can be fixed. In practice, software development organizations experience several obstacles for conducting usability engineering. One suggested...... approach is to train and involve developers in all phases of usability activities from evaluations, to problem reporting, and making redesign proposals. Only limited work has previously investigated the impact of actively involving developers in usability engineering. In this paper, we present two small......, and problem fixing. At the organizational level, we found that the attitude towards and understanding of the role of usability engineering improved....

  9. Considerations for the development of task-based search engines

    DEFF Research Database (Denmark)

    Petcu, Paula; Dragusin, Radu

    2013-01-01

    Based on previous experience from working on a task-based search engine, we present a list of suggestions and ideas for an Information Retrieval (IR) framework that could inform the development of next generation professional search systems. The specific task that we start from is the clinicians......' information need in finding rare disease diagnostic hypotheses at the time and place where medical decisions are made. Our experience from the development of a search engine focused on supporting clinicians in completing this task has provided us valuable insights in what aspects should be considered...... by the developers of vertical search engines....

  10. Research on the Development and Enlightenment of Urban Environmental Engineering

    Science.gov (United States)

    Tian, Mingjing; Li, Guanglou; Zhang, Lu; Shou, Youping; Li, Yajuan; Ye, Wei; Xu, Jing

    2018-04-01

    In recent years, under the promotion of reform and opening up, China's economic development has greatly accelerated, urbanization is also gradually accelerated. In the process of urbanization, there are many problems. The development of environmental engineering is one of the most important points. While building our living environment; we should also pay attention to the implementation of sustainable development strategies. First of all, This paper describes basic situation of environmental engineering, and finally provided some measures to promote the strengthening of China's environmental engineering

  11. The engineering of microprocessor systems guidelines on system development

    CERN Document Server

    1979-01-01

    The Engineering of Microprocessor Systems: Guidelines on System Development provides economical and technical guidance for use when incorporating microprocessors in products or production processes and assesses the alternatives that are available. This volume is part of Project 0251 undertaken by The Electrical Research Association, which aims to give managers and development engineers advice and comment on the development process and the hardware and software needed to support the engineering of microprocessor systems. The results of Phase 1 of the five-phase project are contained in this fir

  12. Engineering for Sustainable Development - An obligatory Skill of the Future Engineer

    DEFF Research Database (Denmark)

    Hauschild, Michael Zwicky; Alting, Leo; Molin, Christine

    2003-01-01

    , Bruxelles (Belgium). Department of Manufacturing Engineering and Management hosted a mini-tutorial on Courses and Curricula in Sustainable Development and Environmental Management at the Technical University of Denmark. The procedings comprise papers from universities and institutions in many countries...

  13. Basic and detail engineering development of PTAMB

    International Nuclear Information System (INIS)

    Beuter, Oscar; Reibel, Jose A.; Mirad, Andres E.; Furriel, Miguel; Diaz, L.

    2009-01-01

    The purpose of the future Treatment and Conditioning of Medium and Low Activity Solid and Liquid Waste Plant (PTAMB) of the National Atomic Energy Commission (CNEA) will be to put up medium and low activity solid and liquid waste and to verify the quality of the conditioned waste generated in Ezeiza Atomic Center (CAE), Constituyentes Atomic Center (CAC) and other national producers outside CNEA. The PTAMB is a Class I Radioactive Installation (according to Basic Standard AR 10.1.1, Rev. 3 RNA, paragraphs 17 and 22) also called Relevant Installation. The aim of this document is to list the steps that carried out the Projects Department of the National Program of Radioactive Waste Management (PNGRR) to arrive to the realization of the detailed engineering of the plant. The project is in Public Tender stage and the beginning of the construction would be March 2010. Once built, the Plant will process the radioactive waste contained in the conceptual engineering, offering more precise control of these and their compatibility with the new final disposal systems to build. (author)

  14. Merged ontology for engineering design: Contrasting empirical and theoretical approaches to develop engineering ontologies

    DEFF Research Database (Denmark)

    Ahmed, Saeema; Storga, M

    2009-01-01

    to developing the ontology engineering design integrated taxonomies (EDIT) with a theoretical approach in which concepts and relations are elicited from engineering design theories ontology (DO) The limitations and advantages of each approach are discussed. The research methodology adopted is to map......This paper presents a comparison of two previous and separate efforts to develop an ontology in the engineering design domain, together with an ontology proposal from which ontologies for a specific application may be derived. The research contrasts an empirical, user-centered approach...

  15. Development of engine sound quality for passenger car with 6 cylinder engine; 6 kito engine joyosha no onshoku kazari

    Energy Technology Data Exchange (ETDEWEB)

    Iwasaki, Y; Miyamoto, K; Yamamoto, K [Toyota Motor Corp., Aichi (Japan)

    1997-10-01

    In recent years, the interior noise has been required not only to reduce the sound pressure level, but also to improve the sound quality, especially during acceleration. This paper describes the development of engine sound quality for the new model `ARISTO (GS300)` with in-line 6 gasoline engine. We used the sound simulator in order to evaluate the engine sound quality during acceleration, and decided the target sound. To attain that sound, the light-weighed Piston and connecting rod, and the improvement of intake system are adopted. 7 refs., 13 figs.

  16. Protein design in systems metabolic engineering for industrial strain development.

    Science.gov (United States)

    Chen, Zhen; Zeng, An-Ping

    2013-05-01

    Accelerating the process of industrial bacterial host strain development, aimed at increasing productivity, generating new bio-products or utilizing alternative feedstocks, requires the integration of complementary approaches to manipulate cellular metabolism and regulatory networks. Systems metabolic engineering extends the concept of classical metabolic engineering to the systems level by incorporating the techniques used in systems biology and synthetic biology, and offers a framework for the development of the next generation of industrial strains. As one of the most useful tools of systems metabolic engineering, protein design allows us to design and optimize cellular metabolism at a molecular level. Here, we review the current strategies of protein design for engineering cellular synthetic pathways, metabolic control systems and signaling pathways, and highlight the challenges of this subfield within the context of systems metabolic engineering. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  17. The development and application of CFD technology in mechanical engineering

    Science.gov (United States)

    Wei, Yufeng

    2017-12-01

    Computational Fluid Dynamics (CFD) is an analysis of the physical phenomena involved in fluid flow and heat conduction by computer numerical calculation and graphical display. The numerical method simulates the complexity of the physical problem and the precision of the numerical solution, which is directly related to the hardware speed of the computer and the hardware such as memory. With the continuous improvement of computer performance and CFD technology, it has been widely applied to the field of water conservancy engineering, environmental engineering and industrial engineering. This paper summarizes the development process of CFD, the theoretical basis, the governing equations of fluid mechanics, and introduces the various methods of numerical calculation and the related development of CFD technology. Finally, CFD technology in the mechanical engineering related applications are summarized. It is hoped that this review will help researchers in the field of mechanical engineering.

  18. The Clean Development Mechanism Re-engineered

    DEFF Research Database (Denmark)

    Lütken, Søren

    2016-01-01

    for engineering such mechanism, or indeed reengineering the CDM itself, to make it a viable mitigation financing tool, providing receipts for payments in the form of certified emission reductions (CER). Two solutions are presented, both of which secure new financing for projects that deliver real and measurable...... emissions reduction benefits on the basis of prospective revenues from emissions reduction: one introduces up-front securitization of the emissions reductions; the other builds on a defined value of the CERs without the need for a carbon price or a market for trading. Most of us use simple heuristics...... time. Simply put CERs are not project finance and do not address project capital needs when most needed — upfront. CER based returns are available only after a project is operational. That is why only one third of registered CDM projects went as far as to get their carefully calculated CERs issued...

  19. The development of biomedical engineering as experienced by one biomedical engineer.

    Science.gov (United States)

    Newell, Jonathan C

    2012-12-12

    This personal essay described the development of the field of Biomedical Engineering from its early days, from the perspective of one who lived through that development. It describes the making of a major invention using data that had been rejected by other scientists, the re-discovery of an obscure fact of physiology and its use in developing a major medical instrument, the development of a new medical imaging modality, and the near-death rescue of a research project. The essay concludes with comments about the development and present status of impedance imaging, and recent changes in the evolution of biomedical engineering as a field.

  20. Developing an Engineering Design Process Assessment using Mixed Methods.

    Science.gov (United States)

    Wind, Stefanie A; Alemdar, Meltem; Lingle, Jeremy A; Gale, Jessica D; Moore, Roxanne A

    Recent reforms in science education worldwide include an emphasis on engineering design as a key component of student proficiency in the Science, Technology, Engineering, and Mathematics disciplines. However, relatively little attention has been directed to the development of psychometrically sound assessments for engineering. This study demonstrates the use of mixed methods to guide the development and revision of K-12 Engineering Design Process (EDP) assessment items. Using results from a middle-school EDP assessment, this study illustrates the combination of quantitative and qualitative techniques to inform item development and revisions. Overall conclusions suggest that the combination of quantitative and qualitative evidence provides an in-depth picture of item quality that can be used to inform the revision and development of EDP assessment items. Researchers and practitioners can use the methods illustrated here to gather validity evidence to support the interpretation and use of new and existing assessments.

  1. Integration of safety engineering into a cost optimized development program.

    Science.gov (United States)

    Ball, L. W.

    1972-01-01

    A six-segment management model is presented, each segment of which represents a major area in a new product development program. The first segment of the model covers integration of specialist engineers into 'systems requirement definition' or the system engineering documentation process. The second covers preparation of five basic types of 'development program plans.' The third segment covers integration of system requirements, scheduling, and funding of specialist engineering activities into 'work breakdown structures,' 'cost accounts,' and 'work packages.' The fourth covers 'requirement communication' by line organizations. The fifth covers 'performance measurement' based on work package data. The sixth covers 'baseline requirements achievement tracking.'

  2. Research and development of turbofan engine for supersonic aircraft. Choonsokukiyo turbofan engine no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Yashima, S [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1992-01-01

    This paper described the researched results of the demonstrator of a turbofan engine for supersonic aircraft (IHI-17). A turbofan engine with an afterburner was experimentally fabricated and various engine tests have been carried out since 1988. Although the engine size is small, the fighter engine specifications were applied to its design and the prior or simultaneous research on each component was carried out. As a result, the system integration technique by which an engine was assembled by integrating each component could be established. New materials and new manufacturing techniques such as turbine blades of single crystal, turbine disks of powder metallurgy and deep chemical milling for a duct were developed to use for the long term engine test and the prospect to commercialization could be obtained. The following techniques have been established and the results satisfying target specifications could be achieved: the three dimensional aerodynamic design of compressor and turbine, the adoption of air blast fuel atomizer to suppress the smoke generation, an afterburner of spray bar system and the mounting type FADEC (full authority digital electronic control) to control the engine with the afterburner. 4 refs., 15 figs., 4 tabs.

  3. Effects of Reynold's number on flight performance of turbofan engine

    Energy Technology Data Exchange (ETDEWEB)

    Kozu, Masao; Yajima, Satoshi [Defense Agency Tokyo (Japan); Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan))

    1988-12-10

    Concerning the performance of the F3-30 turbofan engine which is carried on the intermediate trainer XT-4 of the Air Self Defense Force, tests simulating its flight conditions were conducted at the Altitude Test Facility (ATF) of the Arnold Engineering Development Center (AEDC), U.S. Air Force in order to adjust the effect of Reynold's number corresponding to the flight condition. This report summarizes the results of the above tests. As the results of the tests, it was revealed that in order to calculate with precision the flight performance of the F3-30 turbofan engine, it was required to adjust Reynold's number against the following figures, namely the fan air flow, compressor air flow, compressor adiabatic efficiency, low pressure turbine gas flow and low pressure turbine adiabatic efficiency. The engine performance calculated by using the above adjustments agreed well with the measured values of the ATF tests. 7 refs., 17 figs., 1 tab.

  4. Advanced Engineering Environments for Space Transportation System Development

    Science.gov (United States)

    Thomas, L. Dale; Smith, Charles A.; Beveridge, James

    2000-01-01

    There are significant challenges facing today's launch vehicle industry. Global competition, more complex products, geographically-distributed design teams, demands for lower cost, higher reliability and safer vehicles, and the need to incorporate the latest technologies quicker, all face the developer of a space transportation system. Within NASA, multiple technology development and demonstration projects are underway toward the objectives of safe, reliable, and affordable access to space. New information technologies offer promising opportunities to develop advanced engineering environments to meet these challenges. Significant advances in the state-of-the-art of aerospace engineering practice are envisioned in the areas of engineering design and analytical tools, cost and risk tools, collaborative engineering, and high-fidelity simulations early in the development cycle. At the Marshall Space Flight Center, work has begun on development of an advanced engineering environment specifically to support the design, modeling, and analysis of space transportation systems. This paper will give an overview of the challenges of developing space transportation systems in today's environment and subsequently discuss the advanced engineering environment and its anticipated benefits.

  5. On development of search engine for geodata

    Directory of Open Access Journals (Sweden)

    David Procházka

    2010-01-01

    Full Text Available Effective management and sharing of geodata is one of the priorities of the European Union (INSPIRE activity and companies all around the world. Many different companies and organisations publish their geodata using web mapping services. This situation leads to a multiple publishing of similar or completely same geodata. On the other hand, there is frequently a problem how to determine an appropriate mapserver with the required data. This paper presents a geodata search engine which solves the problem how to access geodata more effectively. Presented solution aggregates data from the different mapservers and provides an interface according to the Open Geospatial Consortium Web Map Server specification. This allows to use our solution in the standard GIS tools as common mapserver. Completely new feature is a request which allows to select map layers which fulfills specified criteria. Selection could be given by keywords in a map layer description and by defining a bounding box on Earth surface. Response is a list of appropriate layers sorted according to their relevance. Presented solution could be among other applications significant source of information for many data mining techniques. It allows to interconnect processed data with their space-temporal context.

  6. Phase 1 Development Testing of the Advanced Manufacturing Demonstrator Engine

    Science.gov (United States)

    Case, Nicholas L.; Eddleman, David E.; Calvert, Marty R.; Bullard, David B.; Martin, Michael A.; Wall, Thomas R.

    2016-01-01

    The Additive Manufacturing Development Breadboard Engine (BBE) is a pressure-fed liquid oxygen/pump-fed liquid hydrogen (LOX/LH2) expander cycle engine that was built and operated by NASA at Marshall Space Flight Center's East Test Area. The breadboard engine was conceived as a technology demonstrator for the additive manufacturing technologies for an advanced upper stage prototype engine. The components tested on the breadboard engine included an ablative chamber, injector, main fuel valve, turbine bypass valve, a main oxidizer valve, a mixer and the fuel turbopump. All parts minus the ablative chamber were additively manufactured. The BBE was successfully hot fire tested seven times. Data collected from the test series will be used for follow on demonstration tests with a liquid oxygen turbopump and a regeneratively cooled chamber and nozzle.

  7. The Global Goals for Sustainable Development in Engineering Education

    DEFF Research Database (Denmark)

    Thuesen, Christian; Geraldi, Joana

    History is full of examples of how engineers for good and bad have invented and implemented technologies, with consequence far beyond their imaginations. Think for instance on the development of the combustion engine which enabled a revolution in transport and individual mobility but at the same...... by across 11 countries conducted among 10,341 respondents finds that engineering indeed played a vital role in creating our past and will continue to play a critical role in shaping our future. While this finding mirrors the common understanding of engineering, the study points to a need to change the role...... students. Our findings from educating more than 500+ students is that the SDGs represent an outstanding tool to convey the importance of engineering and to create a sense of purpose that represent a key driver for motivation. It further it enables collaboration between various disciplines and stimulates...

  8. Non-Toxic Orbital Maneuvering System Engine Development

    Science.gov (United States)

    Green, Christopher; Claflin, Scott; Maeding, Chris; Butas, John

    1999-01-01

    Recent results using the Aestus engine operated with LOx/ethanol propellant are presented. An experimental program at Rocketdyne Propulsion and Power is underway to adapt this engine for the Boeing Reusable Space Systems Division non-toxic Orbital Maneuvering System/Reaction control System (OMS/RCS) system. Daimler-Chrysler Aerospace designed the Aestus as an nitrogen tetroxide/monomethyl hydrazine (NTO/MMH) upper-stage engine for the Ariane 5. The non-toxic OMS/RCS system's preliminary design requires a LOx/ethanol (O2/C2H5OH) engine that operates with a mixture ratio of 1.8, a specific impulse of 323 seconds, and fits within the original OMS design envelope. This paper describes current efforts to meet these requirements including, investigating engine performance using LOx/ethanol, developing the en-ine system sizing package, and meeting the vehicle operation parameters. Data from hot-fire testing are also presented and discussed.

  9. Linear engine development for series hybrid electric vehicles

    Science.gov (United States)

    Toth-Nagy, Csaba

    This dissertation argues that diminishing oil reserves, concern over global climate change, and desire to improve ambient air quality all demand the development of environment-friendly personal transportation. In certain applications, series hybrid electric vehicles offer an attractive solution to reducing fuel consumption and emissions. Furthermore, linear engines are emerging as a powerplant suited to series HEV applications. In this dissertation, a linear engine/alternator was considered as the auxiliary power unit of a range extender series hybrid electric vehicle. A prototype linear engine/alternator was developed, constructed and tested at West Virginia University. The engine was a 2-stroke, 2-cylinder, dual piston, direct injection, diesel engine. Experiment on the engine was performed to study its behavior. The study variables included mass of the translator, amount of fuel injected, injection timing, load, and stroke with operating frequency and mechanical efficiency as the basis of comparison. The linear engine was analyzed in detail and a simple simulation model was constructed to compare the trends of simulation with the experimental data and to expand on the area where the experimental data were lacking. The simulation was based on a simple and analytical model, rather than a detailed and intensely numerical one. The experimental and theoretical data showed similar trends. Increasing translator mass decreased the operating frequency and increased compression ratio. Larger mass and increased compression ratio improved the ability of the engine to sustain operation and the engine was able to idle on less fuel injected into the cylinder. Increasing the stroke length caused the operating frequency to drop. Increasing fueling or decreasing the load resulted in increased operating frequency. This projects the possibility of using the operating frequency as an input for feedback control of the engine. Injection timing was varied to investigate two different

  10. Image encryption with chaotic map and Arnold transform in the gyrator transform domains

    Science.gov (United States)

    Sang, Jun; Luo, Hongling; Zhao, Jun; Alam, Mohammad S.; Cai, Bin

    2017-05-01

    An image encryption method combing chaotic map and Arnold transform in the gyrator transform domains was proposed. Firstly, the original secret image is XOR-ed with a random binary sequence generated by a logistic map. Then, the gyrator transform is performed. Finally, the amplitude and phase of the gyrator transform are permutated by Arnold transform. The decryption procedure is the inverse operation of encryption. The secret keys used in the proposed method include the control parameter and the initial value of the logistic map, the rotation angle of the gyrator transform, and the transform number of the Arnold transform. Therefore, the key space is large, while the key data volume is small. The numerical simulation was conducted to demonstrate the effectiveness of the proposed method and the security analysis was performed in terms of the histogram of the encrypted image, the sensitiveness to the secret keys, decryption upon ciphertext loss, and resistance to the chosen-plaintext attack.

  11. Engineering for Sustainable Development and the Common Good

    Science.gov (United States)

    Kelly, William E.

    2006-01-01

    In 1994, the American Society of Civil Engineers (ASCE) updated its Code of Ethics to include specific statements on sustainable development and at about the same time, 1994, ASCE adopted its Policy 418 on sustainable development. Sustainable development as defined by ASCE "is the challenge of meeting human needs for natural resources, industrial…

  12. Internal combustion engines a detailed introduction to the thermodynamics of spark and compression ignition engines, their design and development

    CERN Document Server

    Benson, Rowland S

    1979-01-01

    Internal Combustion of Engines: A Detailed Introduction to the Thermodynamics of Spark and Compression Ignition Engines, Their Design and Development focuses on the design, development, and operations of spark and compression ignition engines. The book first describes internal combustion engines, including rotary, compression, and indirect or spark ignition engines. The publication then discusses basic thermodynamics and gas dynamics. Topics include first and second laws of thermodynamics; internal energy and enthalpy diagrams; gas mixtures and homocentric flow; and state equation. The text ta

  13. Development of HANARO engineering simulator (I)

    International Nuclear Information System (INIS)

    Jung, Hoan Sung; Han, G. Y.; Kim, M. J.; Kim, Y. K.; Lee, K. H.; Park, S. J.; Kim, H. K.; Park, J. H.

    2001-01-01

    The simulation models for HANARO have been developed. Core dynamics is modeled by two-point kinetics. Thermal-hydraulic characteristics are also modeled for the primary, secondary, and reflector cooling systems. Control algorithms used in the digital controller are modeled to control the reactor in same manner with the real system. Prototype simulator was implemented to test developed models. The computer system for distributed simulation was prepared

  14. Challenges and solutions in natural gas engine development and productions

    Energy Technology Data Exchange (ETDEWEB)

    Ahmadi, Mahdi; Izanloo, Hossein [Irankhodro Powertrain Co. (IPCO) (Iran)

    2008-07-01

    As an alternative fuel, natural gas is generally accepted for internal combustion engines and some developments have been conducted in order to adopt it for the road vehicles and stationary applications. Foresights shows natural gas vehicles will be a part of the future transportation technology regarding to their mid and long-term benefits. Therefore inherent problems of natural gas engine technology should be overcome to produce a competitive engine. In this paper major problems and their possible solutions in developing and producing natural gas engine for passenger cars are detailed and discussed. Challenging materials are sorted and presented in two categorizes: technical and econo-strategical problems. In the technical section major difficulties faced in components or systems of natural gas engine are analysed in different aspects of design, validation, and production. In addition problems arisen from the fuel characteristics which influence the function and durability of engine are argued. Subjects like freezing in gas regulator, cold start fuel injection, gas leakage, impurities within compressed natural gas, variation in fuel composition, thermo-mechanics of cylinder head and block, wear of valve seat inserts, spark plug erosion, back-fire phenomenon, engine oil quality requirement, low power density and mileage are described. In the econo-strategical discussion, challenges like limited gas distribution infrastructure, lack of specific manufacturing standards and codes, and non-dedicated emission standards are explained. In both part of the paper a comprehensive view is extended to clarify the effect, risk and solutions of each problem. Due to the fact that almost all information and analysis presented in this paper are based on the experience of developing a natural gas engine family, and an extensive literature review, discussions and conclusions could be useful as a guide line for future natural gas engine projects. (orig.)

  15. Arnold Sommerfeld. Atomic physicist and messenger of culture 1868-1951. A biography

    International Nuclear Information System (INIS)

    Eckert, Michael

    2013-01-01

    Arnold Sommerfeld is beside Albert Einstein, Niels Bohr, and Max Planck one of the founders of modern atomic and quantum theory. His career began in the 1890th years at the University of Goettingen, the world center of mathematics of that time. Since 1906 he created on the professorship for theoretical physics at the Munich university one of the most important schools of science, the students of which are well-known theorists of the atomic era like as the Nobel-price winners Hans Bethe, Peter Debye, Wolfgang Pauli, and Werner Heisenberg. He also developed far beyond his subject an unprecedented impact. He travelled as ''messenger of culture'' in many countries in order to advertise in the years after the first world war for the reputation of Germany as culture nation. By the nationalsocialism the Munich ''nursery of theoretical physics'' however was prepared an inglorious end, because Sommerfeld counted for a ''main propagandist of Jewish theories''. By the example of this life of a physicist also the eventful history of a whole subject.

  16. Development of an engine system simulation software package - ESIM

    Energy Technology Data Exchange (ETDEWEB)

    Erlandsson, Olof

    2000-10-01

    A software package, ESIM is developed for simulating internal combustion engine systems, including models for engine, manifolds, turbocharger, charge-air cooler (inter cooler) and inlet air heater. This study focus on the thermodynamic treatment and methods used in the models. It also includes some examples of system simulations made with these models for validation purposes. The engine model can be classified as a zero-dimensional, single zone model. It includes calculation of the valve flow process, models for heat release and models for in-cylinder, exhaust port and manifold heat transfer. Models are developed for handling turbocharger performance and charge air cooler characteristics. The main purpose of the project related to this work is to use the ESIM software to study heat balance and performance of homogeneous charge compression ignition (HCCI) engine systems. A short description of the HCCI engine is therefore included, pointing out the difficulties, or challenges regarding the HCCI engine, from a system perspective. However, the relations given here, and the code itself, is quite general, making it possible to use these models to simulate spark ignited, as well as direct injected engines.

  17. Engineering research, development and technology: Thrust area report FY 91

    International Nuclear Information System (INIS)

    1991-01-01

    The mission of the Engineering Research, Development, and Technology Program at Lawrence, Livermore National Laboratory (LLNL) is to develop the technical staff and the technology needed to support current and future LLNL programs. To accomplish this mission, the Engineering Research, Development, and Technology Program has two important goals: (1) to identify key technologies and (2) conduct high quality work to enhance our capabilities in these key technologies. To help focus our efforts, we identify technology thrust areas and select technical leaders for each area. The thrust areas are integrated engineering activities and, rather than being based on individual disciplines, they are staffed by personnel from Electronics Engineering, Mechanical Engineering, and other LLNL organizations, as appropriate. The thrust area leaders are expected to establish strong links to LLNL program leaders and to industry; to use outside and inside experts to review the quality and direction of the work; to use university contacts to supplement and complement their efforts; and to be certain that we are not duplicating the work of others. The thrust area leader is also responsible for carrying out the work that follows from the Engineering Research, Development, and Technology Program so that the results can be applied as early as possible to the needs of LLNL programs. This annual report, organized by thrust area, describes activities conducted within the Program for the fiscal year, 1991. Its intent is to provide timely summaries of objectives, theories, methods, and results

  18. System Engineering and Technical Challenges Overcome in the J-2X Rocket Engine Development Project

    Science.gov (United States)

    Ballard, Richard O.

    2012-01-01

    Beginning in 2006, NASA initiated the J-2X engine development effort to develop an upper stage propulsion system to enable the achievement of the primary objectives of the Constellation program (CxP): provide continued access to the International Space Station following the retirement of the Space Station and return humans to the moon. The J-2X system requirements identified to accomplish this were very challenging and the time expended over the five years following the beginning of the J- 2X effort have been noteworthy in the development of innovations in both the fields for liquid rocket propulsion and system engineering.

  19. Research and development related to the services engineering

    International Nuclear Information System (INIS)

    Rembado, J. L.

    2000-01-01

    In the present paper it is clarified what is understood by the expression R and D, Research and Development in the Servicie Engineering's which support the nuclear power plants exploitation, being more appropriated to talk about Innovation and Technological Development. In this paper it is analysed the need to have an innovation as per the marketing needs and to have a technological development to maintain an independence to let us to keep and increase the company's activity. It is described how the Services Engineering's with technological development turn to equipment suppliers which can be supplied to the nuclear sector as well as to other industrial sectors. Finally, it is described the innovation and technological development evolution, the technological polities objectives and the action lines of Tecnatom, S. A. as a Services Engineering's. (Author)

  20. Engineered barrier development for a nuclear waste repository in basalt

    International Nuclear Information System (INIS)

    Smith, M.J.

    1980-05-01

    The BWIP Engineered Barrier Program has been developed to provide an integrated approach to the development of site-specific Engineered Barrier assemblages for a repository located in basalt. The goal of this program is to specify engineered and natural barriers which will ensure that nuclear and non-radioactive hazardous materials emplaced in a repository in basalt do not exceed acceptable rates of release to the biosphere. A wide range of analytical and experimental activities related to the basalt repository environment, waste package environment, waste/barrier/rock interactions, and barrier performance assessment provide the basis for selection of systems capable of meeting licensing requirements. Work has concentrated on specifying and testing natural and man-made materials which can be used to plug boreholes in basalt and which can be used as multiple barriers to surround nuclear waste forms and containers. The Engineered Barriers Program is divided into two major activities: multiple barrier studies and borehole plugging. 8 figures, 4 tables

  1. Crisis Situations in Engineering Product Development

    DEFF Research Database (Denmark)

    Muenzberg, Christopher; Hammer, Jens; Brem, Alexander

    2016-01-01

    approaches reduce the problem identification time and increase the efficiency of crisis management. The goal of this research is to identify methods which are able to support the crisis management process successfully. Therefore, a literature-based analysis of developing methods, especially TRIZ is conducted......Crisis situations are special situations during the development process. They are characterized by time and handling pressure. Therefore, it is necessary to identify and apply a methodical problem solving approach to overcome these situations. Due to their prescriptive character, problem solving...

  2. Lennart Meri rännak jätkub ajaloos / Arnold Rüütel

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2006-01-01

    Ilmunud ka: Eesti Päevaleht 27. märts, lk. 3, pealkiri: VAbariigi presidendi Arnold Rüütli mälestuskõne president Lennart Mei ärasaatmisel Kadriorus, 26. märtsil 2006 SL Õhtuleht 27. märts lk. 2,8, Järva Teataja 28. märts lk. 2. Eesti Vabariigi presidendi Arnold Rüütli mälestuskõne president Lennart Meri riiklikul hüvastijätutseremoonial 26. märtsil 2006 Kadriorus

  3. Presidentidest usaldas rahvas kõige enam Arnold Rüütlit / Vahur Koorits

    Index Scriptorium Estoniae

    Koorits, Vahur, 1981-

    2009-01-01

    Kaitseministeeriumi korraldatud institutsioonide usaldusväärsuse küsitlusest selgus, et president Arnold Rüütlit usaldas tema ametiajal keskmiselt 79 % Eesti inimestest. President Toomas Hendrik Ilves pälvis 73 % vastanute usalduse ja president Lennart Meri usaldas tema viimasel ametiaastal 70 % küsitletutest. Lisatud joonis: Usaldus taasiseseisvuseaegsete presidentide vastu (aastatel 2001-2008). Arvamust avaldavad president Arnold Rüütel, Postimehe kolumnist Enn Soosaar, uuringufirma Saar Poll juhataja Andrus Saar ja president T. H. Ilvese avalike suhete nõunik Toomas Sildam

  4. Essays in mathematics and its applications in honor of Vladimir Arnold

    CERN Document Server

    Pardalos, Panos

    2016-01-01

    This volume, dedicated to the eminent mathematician Vladimir Arnold, presents a collection of research and survey papers written on a large spectrum of theories and problems that have been studied or introduced by Arnold himself. Emphasis is given to topics relating to dynamical systems, stability of integrable systems, algebraic and differential topology, global analysis, singularity theory and classical mechanics. A number of applications of Arnold’s groundbreaking work are presented. This publication will assist graduate students and research mathematicians in acquiring an in-depth understanding and insight into a wide domain of research of an interdisciplinary nature.

  5. Anesthesia management for pregnant patient with Arnold-Chiari malformation type I: A case report

    Directory of Open Access Journals (Sweden)

    Şaban Yalçın

    2012-06-01

    Full Text Available The Arnold-Chiari I malformation (ACM is a congenitalanomaly characterized by downward herniation of thecerebellar tonsils into the spinal canal. The anomaly maypresent in a variety of ways with vague symptoms suchas head and limb pains, vertigo, hypoesthesia, weaknessin the extremities. Diagnosis is often difficult and thereforedelayed. Measurement of intracranial pressure in thesepatients is an important measure thus precautions shoulbe taken for avoidance of increased intracranial pressure.In this case report, we discussed the anesthetic managementof a pregnant patient with Arnold Chiari I malformationwho underwent an emergency caesarean section.

  6. Sustainable Development in the Engineering Curriculum: Teaching and Learning Resources

    OpenAIRE

    Penlington, Roger; Steiner, Simon

    2014-01-01

    This repository of teaching and learning resources is a companion to the 2nd edition of “An Introduction to Sustainable Development in the Engineering Curriculum”, by Roger Penlington and Simon Steiner, originally created by The Higher Education Academy Engineering Subject Centre, Loughborough University. \\ud The purpose of this collection of teaching and learning re-sources is to provide access, with a brief resumé, to materials in curricula reform, recognition awards, and university movemen...

  7. Development of human factors engineering guide for nuclear power project

    International Nuclear Information System (INIS)

    Wu Dangshi; Sheng Jufang

    1997-01-01

    'THE PRACTICAL GUIDE FOR APPLICATION OF HUMAN FACTORS ENGINEERING TO NUCLEAR POWER PROJECT (First Draft, in Chinese)', which was developed under a research program sponsored by National Nuclear Safety Administration (NNSA) is described briefly. It is hoped that more conscious, more systematical and more comprehensive application of Human Factors Engineering to the nuclear power projects from the preliminary feasibility studies up to the commercial operation will benefit the safe, efficient and economical operations of nuclear power plants in China

  8. Turbulence models development and engineering applications

    International Nuclear Information System (INIS)

    Groetzbach, G.; Ammann, T.; Dorr, B.; Hiltner, I.; Hofmann, S.; Kampczyk, M.; Kimhi, Y.; Seiter, C.; Woerner, M.; Alef, M.; Hennemuth, A.

    1995-01-01

    The FLUTAN code is used for analyzing the decay heat removal in new reactor concepts. The turbulence models applied in FLUTAN are improved by the development of the TURBIT code. TURBIT serves for a numerical simulation of turbulent channel flow. (orig.)

  9. Concurrent Engineering in seafood product development

    DEFF Research Database (Denmark)

    Jonsdottir, Stella; Vesterager, Johan; Børresen, Torger

    1998-01-01

    benefit from the CE approach which can support product developers to provide concurrent specifications for raw materials, ingredients, packaging, and production methods. The approach involves the use of product models from which line extensions are more easily generated than by use of customary stepwise...... techniques. it is anticipated that other food industries also can benefit from the more simultaneous approach...

  10. Development of Toyota new 1GZ-FE engine; Shingata V12 gasoline engine no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kawamura, H; Asahi, T; Goto, M; Endo, K; Terada, M [Toyota Motor Corp., Aichi (Japan)

    1997-10-01

    The first V-12 cylinder engine for passenger car in Japan, the 1GZ-FE, which is the status of high luxury vehicles has been developed. In order to proceed the merit of V-12 cylinder engine, Intelligent Variable Valve Timing (VVT-i) system, Slant squish combustion chamber, Iridium pole spark plug and Intelligent electronic throttle control system were introduced. Through these features this new 1GZ-FE has achieved an overwhelming smoothness and quietness and yet highest torque among the same displacement engine at low and medium engine speed. Additionally the 1GZ-FE achieved good fuel economy and high reliability which exceed any other competitors. 14 refs., 4 figs.

  11. System reliability developments in structural engineering

    International Nuclear Information System (INIS)

    Moses, F.

    1982-01-01

    Two major limitations occur in present structural design code developments utilizing reliability theory. The notional system reliabilities may differ significantly from calibrated component reliabilities. Secondly, actual failures are often due to gross errors not reflected in most present code formats. A review is presented of system reliability methods and further new concepts are developed. The incremental load approach for identifying and expressing collapse modes is expanded by employing a strategy to identify and enumerate the significant structural collapse modes. It further isolates the importance of critical components in the system performance. Ductile and brittle component behavior and strength correlation is reflected in the system model and illustrated in several examples. Modal combinations for the system reliability are also reviewed. From these developments a system factor can be addended to component safety checking equations. Values may be derived from system behavior by substituting in a damage model which accounts for the response range from component failure to collapse. Other strategies are discussed which emphasize quality assurance during design and in-service inspection for components whose behavior is critical to the system reliability. (Auth.)

  12. Development of decommissioning system engineering technology

    International Nuclear Information System (INIS)

    Lee, K. W.; Kim, S. K.; Seo, B. K.

    2012-02-01

    In the decommissioning planning stage, it is important to select the optimized decommissioning process considering the cost and safety. Especially the selection of the optimized decommissioning process is necessary because it affects to improve worker's safety and decommissioning work efficiency. The decommissioning process evaluation technology can provide the optimized decommissioning process as constructing various decommissioning scenarios and it can help to prevent the potential accidents as delivering the exact work procedures to workers and to help workers to perform decommissioning work skillfully. It's necessary to measure the radioactive contamination in the highly contaminated facilities such as hot-cells or glove-boxes to be decommissioned for decommissioning planning. These facilities are very high radiation level, so it is difficult to approach. In this case the detector system is preferable to separate the sensor and electronics, which have to locate in the facility outside to avoid the electric noise and worker's radiation exposure. In this project, we developed the remote detection system for radiation measurement and signal transmission in the high radiation area. In order to minimize worker's exposure when decommissioning highly activated nuclear facilities, it is necessary to develop the remote handling tool to perform the dismantling work remotely. Especially, since cutting, measuring, and decontamination works should be performed remotely in the highly activated area, the remote handling tool for conducting these works should be developed. Therefore, the multi-purpose dismantling machine that can measuring dose, facility cutting, and remote handling for maintenance and decommissioning of highly activated facility should be needed

  13. Developing a new industrial engineering curriculum using a systems engineering approach

    Science.gov (United States)

    Buyurgan, Nebil; Kiassat, Corey

    2017-11-01

    This paper reports on the development of an engineering curriculum for a new industrial engineering programme at a medium-sized private university in the northeast United States. A systems engineering process has been followed to design and develop the new curriculum. Considering the programme curriculum as a system, first the stakeholders have been identified, and some preliminary analysis on their needs and requirements has been conducted. Following that, the phases of conceptual design, preliminary design, and detailed design have been pursued during which different levels of validation, assessment, and evaluation processes have been utilised. In addition, a curriculum assessment and continuous improvement process have been developed to assess the curriculum and the courses frequently. The resulting curriculum is flexible, allowing the pursuit of accelerated graduate programmes, a second major, various minor options, and study-abroad; relevant, tailored to the needs of industry partners in the vicinity; and practical, providing hands-on education, resulting in employment-ready graduates.

  14. Software Engineering Research/Developer Collaborations in 2005

    Science.gov (United States)

    Pressburger, Tom

    2006-01-01

    In CY 2005, three collaborations between software engineering technology providers and NASA software development personnel deployed three software engineering technologies on NASA development projects (a different technology on each project). The main purposes were to benefit the projects, infuse the technologies if beneficial into NASA, and give feedback to the technology providers to improve the technologies. Each collaboration project produced a final report. Section 2 of this report summarizes each project, drawing from the final reports and communications with the software developers and technology providers. Section 3 indicates paths to further infusion of the technologies into NASA practice. Section 4 summarizes some technology transfer lessons learned. Also included is an acronym list.

  15. Systems Engineering Education Development(SEED)Case Study

    Science.gov (United States)

    Bagg, Thomas C., III; Brumfield, Mark D.; Jamison, Donald E.; Granata, Raymond L.; Casey, Carolyn A.

    2003-01-01

    The Systems Engineering Development Program (SEED) was initiated to help Goddard resolve a Systems Engineering skill shortage. The chronology of events and the experiences of the pilot program are outlined to describe the development of the present program. The program goals are included in order to give a focus on what the developers saw as the program drivers. Lessons learned from a pilot program were incorporated into the present program. This program is constantly learning from its past efforts and looks for continuous improvement. We list several future ideas for improvement and change.

  16. The contribution of bacterial genome engineering to sustainable development.

    Science.gov (United States)

    Reuß, Daniel R; Commichau, Fabian M; Stülke, Jörg

    2017-09-01

    The United Nations' Sustainable Development Goals define important challenges for the prosperous development of mankind. To reach several of these goals, among them the production of value-added compounds, improved economic and ecologic balance of production processes, prevention of climate change and protection of ecosystems, the use of engineered bacteria can make valuable contributions. We discuss the strategies for genome engineering and how they can be applied to meet the United Nations' goals for sustainable development. © 2017 The Authors. Microbial Biotechnology published by John Wiley & Sons Ltd and Society for Applied Microbiology.

  17. Discussion on the Development of Green Chemistry and Chemical Engineering

    Science.gov (United States)

    Zhang, Yunshen

    2017-11-01

    Chemical industry plays a vital role in the development process of national economy. However, in view of the special nature of the chemical industry, a large number of poisonous and harmful substances pose a great threat to the ecological environment and human health in the entire process of raw material acquisition, production, transportation, product manufacturing, and the final practical application. Therefore, it is a general trend to promote the development of chemistry and chemical engineering towards a greener environment. This article will focus on some basic problems occurred in the development process of green chemistry and chemical engineering.

  18. Arnold Rüütel: riigikogu peab hoiduma Iraagi küsimuses populismist / Arnold Rüütel ; intervjueerinud Urmet Kook

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2006-01-01

    President Arnold Rüütel vastab küsimustele, mis puudutavad tema tervist, presidendiks kandideerimist, tema maailmavaadet ja minevikku ning suhet religiooniga, Keskerakonna ja Rahvaliidu koostöölepingut, 1991. aasta putšistide nimetatud Eesti asevalitsejat, Venemaa hiljutist nooti seoses piirilepinguga, presidendi edasisi plaane, samuti tema suhtumist kohustuslikku religiooniõpetusse, Iraagi-missiooni pikendamisse, võõrtööjõu sissetoomisse

  19. Case studies for developing globally responsible engineers

    OpenAIRE

    Global Dimension in Engineering Education

    2015-01-01

    Document realitzat amb un ajut financer de la Unió Europea. Per poder accedir al material complementari per a docents dels 28 casos estudi que formen el llibre, activeu el "Document relacionat" Col·lecció de 28 casos estudi per a professors d'enginyeria: 1. Rural development and planning in LDCs: the “Gamba Deve – Licoma axis”,district of Caia, Mozambique 2. Reducing the impact of soil erosion and reservoir siltation on agricultural production and water availability: the case stu...

  20. Systems Engineering Technical Leadership Development Program

    Science.gov (United States)

    2012-08-30

    a penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. 1. REPORT DATE 30 AUG...topics and elements were collected from a wide variety of sources, including NASA6, Nokia , BAE Systems, the DoD, and the Australian government to develop...WHS TOO009 RT0004 Report No. SERC-2012-TR-034-1 August 30, 2012 UNCLASSIFIED 17 solutions to pursue and why they should be built. 2. Help teams

  1. Developing a Conceptual Design Engineering Toolbox and its Tools

    Directory of Open Access Journals (Sweden)

    R. W. Vroom

    2004-01-01

    Full Text Available In order to develop a successful product, a design engineer needs to pay attention to all relevant aspects of that product. Many tools are available, software, books, websites, and commercial services. To unlock these potentially useful sources of knowledge, we are developing C-DET, a toolbox for conceptual design engineering. The idea of C-DET is that designers are supported by a system that provides them with a knowledge portal on one hand, and a system to store their current work on the other. The knowledge portal is to help the designer to find the most appropriate sites, experts, tools etc. at a short notice. Such a toolbox offers opportunities to incorporate extra functionalities to support the design engineering work. One of these functionalities could be to help the designer to reach a balanced comprehension in his work. Furthermore C-DET enables researchers in the area of design engineering and design engineers themselves to find each other or their work earlier and more easily. Newly developed design tools that can be used by design engineers but have not yet been developed up to a commercial level could be linked to by C-DET. In this way these tools can be evaluated in an early stage by design engineers who would like to use them. This paper describes the first prototypes of C-DET, an example of the development of a design tool that enables designers to forecast the use process and an example of the future functionalities of C-DET such as balanced comprehension.

  2. Engineering Ethics Education from the Viewpoint of Development Psychology

    Science.gov (United States)

    Hamazaki, Takashi

    This paper is outline for the development of children's mind in modern family and school, and is reviewed on the development theory of morality and prosociality related to engineering ethics education. In particular we are reviewed on the discipline and education of morality and prosociality from infancy to adulthood.

  3. Where Is "Community"?: Engineering Education and Sustainable Community Development

    Science.gov (United States)

    Schneider, J.; Leydens, J. A.; Lucena, J.

    2008-01-01

    Sustainable development initiatives are proliferating in the US and Europe as engineering educators seek to provide students with knowledge and skills to design technologies that are environmentally sustainable. Many such initiatives involve students from the "North," or "developed" world building projects for villages or…

  4. Component-based development of software language engineering tools

    NARCIS (Netherlands)

    Ssanyu, J.; Hemerik, C.

    2011-01-01

    In this paper we outline how Software Language Engineering (SLE) could benefit from Component-based Software Development (CBSD) techniques and present an architecture aimed at developing a coherent set of lightweight SLE components, fitting into a general-purpose component framework. In order to

  5. Dual deflectable beam strip engine development.

    Science.gov (United States)

    Dulgeroff, C. R.; Zuccaro, D. E.; Kami, S.; Schnelker, D. E.; Ward, J. W.

    1972-01-01

    This paper describes a dual beam thruster that has been designed, constructed, and tested. The system is suitable for two-axes attitude control and is comprised of two orthogonal strips, each capable of producing 0.30 mlb thrust and beam deflections of more than plus or minus 20 deg. The nominal specific impulse for the thruster is 5000 sec, and the thrust level from each strip can be varied from 0 to 100%. Neutralizer filaments that were developed and life tested over 2000 hours producing more than 40 mA of electron emission per watt of input power are also discussed. The system power required for clean ionizers is approximately 200 W.

  6. Development of Czechoslovak nuclear power engineering

    International Nuclear Information System (INIS)

    Keher, J.

    1985-01-01

    The output of Czechoslovak nuclear power plants is envisaged at 2200 MW by 1985, 4400 MW by 1990 and 10,280 MW by the year 2000. The operation so far is assessed of Bohunice V-1 and Bohunice V-2 power plants as is the construction of the Dukovany nuclear power plant. International cooperation in the fulfilment of the nuclear power programme is based on the General Agreement on Cooperation in the Prospective Development and Interlinkage of CMEA Power Systems to the year 1990, the Agreement on Multilateral International Specialization and Cooperation of Production and on Mutual Deliveries of Nuclear Power Plant Equipment. The most important factor in international cooperation is the Programme of Cooperation between the CSSR and the USSR. The primary target in the coming period is the Temelin nuclear power plant project and the establishment of unified control of the nuclear power complex. (M.D.)

  7. THE DEVELOPMENT OF A STRATEGIC INDUSTRIAL ENGINEERING PHILOSOPHY

    Directory of Open Access Journals (Sweden)

    P. Leonard

    2012-01-01

    Full Text Available

    ENGLISH ABSTRACT: The proposed expansion of the Industrial Engineering discipline, termed Strategic Industrial Engineering, holds that scientific industrial engineering knowledge may be applied to capitalistic systems with the strategic goal of maximising wealth for the corporate shareholders. This paper provides an overview of the development of such a Strategic Industrial Engineering Philosophy and discusses the possible application of this philosophy in improving the capital productivity of an organisation.

    AFRIKAANSE OPSOMMING: Die voorgestelde uitbreiding van die Bedryfsingenieurswesedissipline, genaamd Strategiese Bedryfsingenieurswese, beweer dat wetenskaplike bedryfsingenieurswesekennis toegepas mag word op kapitalistiese stelsels met die maksimisering van welvaart vir die korporatiewe aandeelhouers as die strategiese doelwit. Hierdie artikel verskaf ’n oorsig van die ontwikkeling van so ’n Strategiese Bedryfsingenieurswesefilosofie en bespreek die moontlike toepassing van hierdie filosofie in die verbetering van die kapitaalproduktiwiteit van ’n onderneming.

  8. Benefits of reverse engineering technologies in software development makerspace

    Directory of Open Access Journals (Sweden)

    Aabidi M.H.

    2017-01-01

    Full Text Available In the recent decades, the amount of data produced by scientific, engineering, and life science applications has increased with several orders of magnitude. In parallel with this development, the applications themselves have become increasingly complex in terms of functionality, structure, and behavior. In the same time, development and production cycles of such applications exhibit a tendency of becoming increasingly shorter, due to factors such as market pressure and rapid evolution of supporting and enabling technologies. As a consequence, an increasing fraction of the cost of creating new applications and manufacturing processes shifts from the creation of new artifacts to the adaption of existing ones. A key component of this activity is the understanding of the design, operation, and behavior of existing manufactured artifacts, such as software code bases, hardware systems, and mechanical assemblies. For instance, in the software industry, it is estimated that maintenance costs exceed 80% of the total costs of a software product's lifecycle, and software understanding accounts for as much as half of these maintenance costs. To facilitate the software development process, it would be ideal to have tools that automatically generate or help to generate UML (Unified Modeling Language models from source code. Reverse engineering the software architecture from source code provides a valuable service to software practitioners. Case tools implementing MDA and reverse-engineering constitute an important opportunity of software development engineers. So MDA and reverse engineering is an important key witch make makerspace more productive and more efficient.

  9. DEVELOPMENT OF OPERATING DRIVE SYSTEMS IN ENGINEERING EQUIPMENT

    Directory of Open Access Journals (Sweden)

    A. A. Kotlobai

    2015-01-01

    Full Text Available Engineering machines being in operational service with military units of  engineer troops are fit to their purpose and their application is relevant in modern conditions. Maintenance of operating conditions in engineering equipment which was produced earlier by the USSR enterprises is considered as a rather complicated task due to lack of spare parts because their production has been discontinued.One of the approaches used for maintenance of engineering equipment combat capabilities is modernization of operating drive systems that presupposes replacement of mechanical systems in working element drives by hydrostatic drives which are realized while using modern element base. Usage of hydraulic units in drive systems being in mass production for replacement of mechanical systems manufactured earlier in small batches makes it possible to reduce labour inputs for maintenance and repair of machines. The paper presents some possibilities for development of operating drive systems in engineering equipment. The proposed approach is given through an example of  engineering obstacle-clearing vehicle (IMR-2M and excavation machines (MDK-3 and MDK-2M.Application of a hydraulic drive in working elements of the excavation machines permits to withdraw from cardan  shafts, a gear box, a rotary gear and an overload clutch. A hydraulic motor of the cutter and thrower drive is mounted  on a working element gearbox. While executing modernization of hydraulic systems in excavation machines a pump unit has been proposed for the cutter and thrower drive which consists of a controlled pump and a system for automatic maintenance of the pump operational parameters. While developing the operating drive systems in engineering equipment in accordance with the proposed requirements it is possible to simplify drive systems of working elements and  ensure reliable machinery operation in the units of engineer troops. 

  10. Engineering research, development and technology. Thrust area report, FY93

    Energy Technology Data Exchange (ETDEWEB)

    1994-05-01

    The mission of the Engineering Research, Development, and Technology Program at Lawrence Livermore National Laboratory (LLNL) is to develop the technical staff, tools, and facilities needed to support current and future LLNL programs. The efforts are guided by a dual-benefit research and development strategy that supports Department of Energy missions, such as national security through nuclear deterrence and economic competitiveness through partnerships with U.S. industry. This annual report, organized by thrust area, describes the activities for the fiscal year 1993. The report provides timely summaries of objectives, methods, and results from nine thrust areas for this fiscal year: Computational Electronics and Electromagnetics; Computational Mechanics; Diagnostics and Microelectronics; Fabrication Technology; Materials Science and Engineering; Power Conversion Technologies; Nondestructive Evaluation; Remote Sensing, Imaging, and Signal Engineering; and Emerging Technologies. Separate abstracts were prepared for 47 papers in this report.

  11. Policy Diversity as an Engine of Development

    Directory of Open Access Journals (Sweden)

    Daniel Daianu

    2004-06-01

    policy diversity to operate as a means to foster economic development; that there might be a paradigmatic cycle in the dynamic of economic policies

  12. Developments in environmental and engineering law in 1990

    International Nuclear Information System (INIS)

    Brandner, T.

    1991-01-01

    The detailed and clear compilation for the period 1.1.1990-31.1.1991 covers the following topics: Environmental and engineering law in the German unification process; superordinate developments in the EG and in Germany, in particular: Draft Federal Environmental Code, Civil Environmental Liability Act, EIA, German Federal Environmental Foundation; technological safety; climate protection - international agreements, EC law, developments in Germany; air and noise pollution control law; atomic and radiation protection law - point of departure, legislation, individual questions: Federal supervision, nuclear disposal and recycling. Moreover: Environmental concerns in regional planning; the law of nature conservation, water protection, waste management, hazardous materials, genetic engineering and soil protection. (HSCH) [de

  13. Quality functions for requirements engineering in system development methods.

    Science.gov (United States)

    Johansson, M; Timpka, T

    1996-01-01

    Based on a grounded theory framework, this paper analyses the quality characteristics for methods to be used for requirements engineering in the development of medical decision support systems (MDSS). The results from a Quality Function Deployment (QFD) used to rank functions connected to user value and a focus group study were presented to a validation focus group. The focus group studies take advantage of a group process to collect data for further analyses. The results describe factors considered by the participants as important in the development of methods for requirements engineering in health care. Based on the findings, the content which, according to the user a MDSS method should support is established.

  14. NTRCI Legacy Engine Research and Development Project Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Smith-Holbert, Connie [National Transportation Research Center, Inc., Knoxville, TN (United States); Petrolino, Joseph [National Transportation Research Center, Inc., Knoxville, TN (United States); Watkins, Bart [Power Source Technologies Inc., Corvallis, OR (United States); Irick, David [Power Source Technologies Inc., Corvallis, OR (United States)

    2011-12-31

    The Legacy engine is a completely new design, transitional diesel engine, replacing the reciprocating engine with a rotary engine. The Legacy engine offers significant advances over conventional internal combustion engines in 1) power to weight ratio; 2) multiple fuel acceptance; 3) fuel economy; and 4) environmental compliance. These advances are achieved through a combination of innovative design geometry, rotary motion, aspiration simplicity, and manufacturing/part simplicity. The key technical challenge to the Legacy engine's commercialization, and the focus of this project, was the development of a viable roton tip seal. The PST concept for the roton tip seal was developed into a manufacturable design. The design was evaluated using a custom designed and fabricated seal test fixture and further refined. This design was incorporated into the GEN2.5A prototype and tested for achievable compression pressure. The Decision Point at the end of Phase 1 of the project (described below) was to further optimize the existing tip seal design. Enhancements to the tip seal design were incorporated into the GEN2.5B prototype and tested and evaluated using the iterative research strategy described below. Compression pressures adequate for compression ignition of diesel fuel were achieved, although not consistently in all combustion volumes. The variation in compression pressures was characterized versus design features. As the roton tip seal performance was improved, results pointed toward inadequate performance of the housing side seals. Enhancement of the housing side seal system was accomplished using a custom designed side seal test fixture. The design enhancements developed with the test fixture were also incorporated into the GEN2.5B prototype and tested and evaluated using the iterative research strategy described below. Finally, to simplify the requirements for the roton tip seals and to enhance the introduction and combustion of fuel, a flush-mount fuel injector

  15. Architecture independent environment for developing engineering software on MIMD computers

    Science.gov (United States)

    Valimohamed, Karim A.; Lopez, L. A.

    1990-01-01

    Engineers are constantly faced with solving problems of increasing complexity and detail. Multiple Instruction stream Multiple Data stream (MIMD) computers have been developed to overcome the performance limitations of serial computers. The hardware architectures of MIMD computers vary considerably and are much more sophisticated than serial computers. Developing large scale software for a variety of MIMD computers is difficult and expensive. There is a need to provide tools that facilitate programming these machines. First, the issues that must be considered to develop those tools are examined. The two main areas of concern were architecture independence and data management. Architecture independent software facilitates software portability and improves the longevity and utility of the software product. It provides some form of insurance for the investment of time and effort that goes into developing the software. The management of data is a crucial aspect of solving large engineering problems. It must be considered in light of the new hardware organizations that are available. Second, the functional design and implementation of a software environment that facilitates developing architecture independent software for large engineering applications are described. The topics of discussion include: a description of the model that supports the development of architecture independent software; identifying and exploiting concurrency within the application program; data coherence; engineering data base and memory management.

  16. Sustainable Development as a Meta-Context for Engineering Education

    Directory of Open Access Journals (Sweden)

    Karel Mulder

    2013-12-01

    Full Text Available At the end of the first decade of the twenty-first century, there is unprecedented awareness of the need for a transformation in development, to meet the needs of the present while also preserving the ability of future generations to meet their own needs. However, within engineering, educators still tend to regard such development as an ‘aspect’ of engineering rather than an overarching meta-context, with ad hoc and highly variable references to topics. Furthermore, within a milieu of interpretations there can appear to be conflicting needs for achieving sustainable development, which can be confusing for students and educators alike. Different articulations of sustainable development can create dilemmas around conflicting needs for designers and researchers, at the level of specific designs and (sub- disciplinary analysis. Hence sustainability issues need to be addressed at a meta-level using a whole of system approach, so that decisions regarding these dilemmas can be made. With this appreciation, and in light of curriculum renewal challenges that also exist in engineering education, this paper considers how educators might take the next step to move from sustainable development being an interesting ‘aspect’ of the curriculum, to sustainable development as a meta-context for curriculum renewal. It is concluded that capacity building for such strategic considerations is critical in engineering education.

  17. Development of Implantable Medical Devices: From an Engineering Perspective

    Directory of Open Access Journals (Sweden)

    Yeun-Ho Joung

    2013-09-01

    Full Text Available From the first pacemaker implant in 1958, numerous engineering and medical activities for implantable medical device development have faced challenges in materials, battery power, functionality, electrical power consumption, size shrinkage, system delivery, and wireless communication. With explosive advances in scientific and engineering technology, many implantable medical devices such as the pacemaker, cochlear implant, and real-time blood pressure sensors have been developed and improved. This trend of progress in medical devices will continue because of the coming super-aged society, which will result in more consumers for the devices. The inner body is a special space filled with electrical, chemical, mechanical, and marine-salted reactions. Therefore, electrical connectivity and communication, corrosion, robustness, and hermeticity are key factors to be considered during the development stage. The main participants in the development stage are the user, the medical staff, and the engineer or technician. Thus, there are three different viewpoints in the development of implantable devices. In this review paper, considerations in the development of implantable medical devices will be presented from the viewpoint of an engineering mind.

  18. Composition of the essential oils of Pinus nigra Arnold from Turkey

    OpenAIRE

    Turkey, Composition of the essential oils of Pin

    2010-01-01

    Essential oil composition of the needles of Pinus nigra Arnold collected from different localities in Turkey was investigated by GC and GC/MS. The main components in the oils were a-pinene, b-pinene, b-caryophyllene, and germacrene D.

  19. Composition of the essential oils of Pinus nigra Arnold from Turkey

    OpenAIRE

    Turkey, Composition of the essential oils of Pin; SEZİK, Ekrem; ÜSTÜN, Osman; DEMİRCİ, Betül; BAŞER, K. Hüsnü Can

    2014-01-01

    Essential oil composition of the needles of Pinus nigra Arnold collected from different localities in Turkey was investigated by GC and GC/MS. The main components in the oils were a-pinene, b-pinene, b-caryophyllene, and germacrene D.

  20. Rüütel declines May 9 Moscow invitation / Arnold Rüütel

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2005-01-01

    President Arnold Rüütli avaldus 7. märtsil 2005, milles ta teatab oma otsusest mitte vastu võtta kutset osaleda selle aasta 9. mail Suures Isamaasõjas saavutatud võidu 60. aastapäeva pidustustel Moskvas

  1. Positive semidefinite matrix completion, universal rigidity and the Strong Arnold Property

    NARCIS (Netherlands)

    Laurent, Monique; Varvitsiotis, A.

    This paper addresses the following three topics: positive semidefinite (psd) matrix completions, universal rigidity of frameworks, and the Strong Arnold Property (SAP). We show some strong connections among these topics, using semidefinite programming as unifying theme. Our main contribution is a

  2. Maandatud pinged igavas provintsiriigis - Arnold Rüütli viis aastat Kadriorus / Ivar Tallo

    Index Scriptorium Estoniae

    Tallo, Ivar, 1964-

    2006-01-01

    Avaliku halduse ekspert analüüsib president Arnold Rüütli tegevust. Võrdlus president Lennart Meriga. Presidendi kantseleist. Vt. samas: Eesti Vabariigi president on meie põhiseaduse järgi Eesti riigipea, kellel on 20 konkreetset ametiülesannet. Lisa: President Rüütli tähtsamad abilised esimesel ametiajal

  3. Arnold Rüütel superstar ehk kevadine veinituur Gruusiasse / Raul Ranne

    Index Scriptorium Estoniae

    Ranne, Raul

    2006-01-01

    President Arnold Rüütli visiidist Gruusiasse. Vt. samas lk. A14 intervjuud presidendi kaaskonnas olnud suurettevõtja Urmas Sõõrumaaga. Sõõrumaa: "Ma soovitan Gruusiat!". Vabariigi Presidendi ametlik visiit Gruusia Vabariiki 9.-13.05.2006

  4. Vladimir I Arnold - Collected Works Representations of Functions, Celestial Mechanics, and KAM Theory 1957-1965

    CERN Document Server

    Arnold, Vladimir I; Khesin, Boris

    2010-01-01

    Vladimir Arnold is one of the great mathematical scientists of our time. He is famous for both the breadth and the depth of his work. At the same time he is one of the most prolific and outstanding mathematical authors. This first volume of his Collected Works focuses on representations of functions, celestial mechanics, and KAM theory.

  5. Anesthetic management in a child with Arnold-Chiari malformation and bilateral vocal cord paralysis.

    NARCIS (Netherlands)

    Setz, A.C.W.; Boer, H.D. de; Driessen, J.J.; Scheffer, G.J.

    2005-01-01

    We report a case of a child who was scheduled for an emergency ventriculoperitoneal shunt procedure. The patient had a type II Arnold-Chiari malformation (ACM) and associated hydrocephalus and presented with near complete respiratory obstruction from bilateral abductor vocal cord palsy. Early

  6. Ando Lepsi sõnavõtt Arnold Rüütli juubelil / Ando Leps

    Index Scriptorium Estoniae

    Leps, Ando, 1935-

    2008-01-01

    10. mail 2008 Eesti Rahvusraamatukogu konverentsisaalis Rahvusliku Arengu Fondi ettekandehommikul peetud tervituskõne president Arnold Rüütli 80. sünnipäeva puhul. Kõnes saavad kriitika osaliseks presidendid Konstantin Päts, Lennart Meri ja Toomas Hendrik Ilves

  7. Spectral decomposition of the stretching dynamics of the Arnold cat map

    International Nuclear Information System (INIS)

    Hasegawa, Hiroshi H.; Driebe, Dean J.; Li, C.-B.

    2003-01-01

    Using the Markov partition of the Arnold cat map on the covering space allows for the introduction of a stable basis in which the Frobenius-Perron operator may be decomposed. We consider in detail the stretching dynamics on the partition of the transformation that yields the cat map under two iterations. The discrete decay modes of the system are constructed

  8. Personal benefits of public open space: a case study in Boston's Arnold Arboretum

    Science.gov (United States)

    Thomas A. More; John Blackwell

    1998-01-01

    Managers of urban parks need to document the benefits that their parks produce. Use level is a typical measure of such benefits, but simple use statistics can mask the rich diversity of people and activities that the parks serve. This study examined the uses and users of Boston's Arnold Arboretum during late summer in 1992. On 25 sample days, we recorded...

  9. Vladimir I. Arnold collected works : hydrodynamics, bifurcation theory, algebraic geometry : 1965-1972

    CERN Document Server

    Arnold, Vladimir I; Khesin, Boris; Marsden, Jerrold E; Varchenko, AN; Vassiliev, Victor A; Viro, Oleg Yanovich; Zakalyukin, Vladimir

    2013-01-01

    Vladimir Arnold was one of the great mathematical scientists of our time. He is famous for both the breadth and the depth of his work. At the same time he is one of the most prolific and outstanding mathematical authors. This second volume of his ""Collected Works"" focuses on hydrodynamics, bifurcation theory, and algebraic geometry.

  10. Analysis of projects development of enterprises in engineering industries in Khmelnytskyi region

    OpenAIRE

    SHKODA M.S.

    2012-01-01

    This article analyzes the use of development projects in the engineering industry of Khmelnitsky region. The current state of engineering field. Solves warehouse development projects engineering enterprises and activities to enhance their implementation.

  11. Career development in Bioengineering/Biomedical Engineering: a student's roadmap.

    Science.gov (United States)

    Abu-Faraj, Ziad O

    2008-01-01

    Bioengineering/biomedical engineering education has progressed since the late 1950s and is still evolving in leading academic institutions worldwide. Today, Bioengineering/Biomedical Engineering is acclaimed as one of the most reputable fields within the global arena, and will likely be the catalyst for any future breakthroughs in Medicine and Biology. This paper provides a set of strategies and recommendations to be pursued by individuals aiming at planning and developing careers in this field. The paper targets the international student contemplating bioengineering/biomedical engineering as a career, with an underlying emphasis on the student within developing and transitional countries where career guidance is found deficient. The paper also provides a comprehensive definition of the field and an enumeration of its subdivisions.

  12. Nuclear engineering education: A competence based approach to curricula development

    International Nuclear Information System (INIS)

    2014-01-01

    Maintaining nuclear competencies in the nuclear industry is a one of the most critical challenges in the near future. With the development of a number of nuclear engineering educational programmes in several States, this publication provides guidance to decision makers in Member States on a competence based approach to curricula development, presenting the established practices and associated requirements for educational programmes in this field. It is a consolidation of best practices that will ensure sustainable, effective nuclear engineering programmes, contributing to the safe, efficient and economic operation of nuclear power plants. The information presented is drawn from a variety of recognized nuclear engineering programmes around the world and contributes to the main areas that are needed to ensure a viable and robust nuclear industry

  13. Using a systems engineering process to develop engineered barrier system design concepts

    International Nuclear Information System (INIS)

    Jardine, L.J.; Short, D.W.

    1991-05-01

    The methodology used to develop conceptual designs of the engineered barrier system and waste packages for a geologic repository is based on an iterative systems engineering process. The process establishes a set of general mission requirements and then conducts detailed requirements analyses using functional analyses, system concept syntheses, and trade studies identifications to develop preliminary system concept descriptions. The feasible concept descriptions are ranked based on selection factors and criteria and a set of preferred concept descriptions is then selected for further development. For each of the selected concept descriptions, a specific set of requirements, including constraints, is written to provide design guidance for the next and more detailed phase of design. The process documents all relevant waste management system requirements so that the basis and source for the specific design requirements are traceable and clearly established. Successive iterations performed during design development help to insure that workable concepts are generated to satisfy the requirements. 4 refs., 2 figs

  14. The development and application of engineered proteins for bioremediation

    Energy Technology Data Exchange (ETDEWEB)

    Trewhella, J. [ed.

    1995-09-26

    Clean up of the toxic legacy of the Cold War is projected to be the most expensive domestic project the nation has yet undertaken. Remediation of the Department of Energy and Department of Defense toxic waste sites alone are projected to cost {approximately}$1 trillion over a 20-30 year period. New, cost effective technologies are needed to attack this enormous problem. Los Alamos has put together a cross-divisional team of scientist to develop science based bioremediation technology to work toward this goal. In the team we have expertise in: (1) molecular, ecosystem and transport modeling; (2) genetic and protein engineering; (3) microbiology and microbial ecology; (4) structural biology; and (5) bioinorganic chemistry. This document summarizes talks at a workshop of different aspects of bioremediation technology including the following: Introducing novel function into a Heme enzyme: engineering by excavation; cytochrome P-450: ideal systems for bioremediation?; selection and development of bacterial strains for in situ remediation of cholorinated solvents; genetic analysis and preparation of toluene ortho-monooxygenase for field application in remediation of trichloroethylene; microbial ecology and diversity important to bioremediation; engineering haloalkane dehalogenase for bioremediation; enzymes for oxidative biodegradation; indigenous bacteria as hosts for engineered proteins; performance of indigenous bacterial, hosting engineered proteins in microbial communities.

  15. Development of security engineering curricula at US universities

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, M.L.

    1998-08-01

    The Southwest Surety Institute was formed in June 1996 by Arizona State University (ASU), New Mexico Institute of Mining and Technology (NM Tech), New Mexico State University (NMSU), and Sandia National Laboratories (SNL) to provide educational programs in Security Engineering, and to conduct research and development in security technologies. This is the first science-based program of its kind in the US, focused on educating Security Engineers to help government and industry address their security needs. Each member brings a unique educational capability to the Institute. NM Tech has a formidable explosives testing and evaluation facility. ASU is developing a Masters program in Security Engineering at their School of Technology located on a new campus in Mesa, Arizona. NMSU provides a Security Technology minor, merging programs in Criminal Justice and Engineering Technology. The Sandia National Laboratories security system design and evaluation process forms the basis for the Security Engineering curricula. In an effort to leverage the special capabilities of each university, distance education will be used to share courses among Institute members and eventually with other sites across the country.

  16. Application of software engineering to development of reactor safety codes

    International Nuclear Information System (INIS)

    Wilburn, N.P.; Niccoli, L.G.

    1981-01-01

    Software Engineering, which is a systematic methodology by which a large scale software development project is partitioned into manageable pieces, has been applied to the development of LMFBR safety codes. The techniques have been applied extensively in the business and aerospace communities and have provided an answer to the drastically increasing cost of developing and maintaining software. The five phases of software engineering (Survey, Analysis, Design, Implementation, and Testing) were applied in turn to development of these codes, along with Walkthroughs (peer review) at each stage. The application of these techniques has resulted in SUPERIOR SOFTWARE which is well documented, thoroughly tested, easy to modify, easier to use and maintain. The development projects have resulted in lower overall cost. (orig.) [de

  17. Development of university-industry partnerships in railroad engineering education

    Science.gov (United States)

    Lautala, Pasi T.

    to high demand for rail transportation and an older engineering workforce with the greatest demand for civil, electrical and mechanical engineers with bachelor's degrees. The rail industry and universities have grown apart over the past several decades, as rail programs and courses were abandoned at universities and there were very limited recruitment and research activities by the railroads at universities. Today, specialized course(s) in rail topics are offered at approximately three percent of ABET accredited civil engineering programs in the U.S. and only 16 percent of engineers who responded to the survey had received university exposure to rail topics. The research findings suggest that increased university participation has the potential to assist the rail industry in all aspects related to attracting, educating, recruiting, training and retaining engineering graduates. The primary advantages would be greater industry visibility and student knowledge in rail topics. Increased prior knowledge, on the other hand, improves the effectiveness of industry training programs and offers a potential for sizable training cost reductions. As a final conclusion, the research suggests that the most effective approach for developing future railroad engineers is a balancing act where the responsibilities should be shared by the rail industry and universities based on each others strengths. University participation should include multiple types and levels, including introductory lectures, co-op/internship programs, courses in railroad engineering, and a minor or certificate in railroad engineering that would include several courses. Due to the urgent demand for railroad engineers and time it takes to rebuild the expertise on campuses, the development process should begin immediately, be incremental, and utilize concepts, such as cooperation with other universities or engineer-in-residence, that reduce the demand of internal university resources. The challenges to the process

  18. Advanced diesel engine component development program, tasks 4-14

    Science.gov (United States)

    Kaushal, Tony S.; Weber, Karen E.

    1994-01-01

    This report summarizes the Advanced Diesel Engine Component Development (ADECD) Program to develop and demonstrate critical technology needed to advance the heavy-duty low heat rejection engine concept. Major development activities reported are the design, analysis, and fabrication of monolithic ceramic components; vapor phase and solid film lubrication; electrohydraulic valve actuation; and high pressure common rail injection. An advanced single cylinder test bed was fabricated as a laboratory tool in studying these advanced technologies. This test bed simulates the reciprocator for a system having no cooling system, turbo compounding, Rankine bottoming cycle, common rail injection, and variable valve actuation to achieve fuel consumption of 160 g/kW-hr (.26 lb/hp-hr). The advanced concepts were successfully integrated into the test engine. All ceramic components met their functional and reliability requirements. The firedeck, cast-in-place ports, valves, valve guides, piston cap, and piston ring were made from silicon nitride. Breakthroughs required to implement a 'ceramic' engine included the fabrication of air-gap cylinder heads, elimination of compression gaskets, machining of ceramic valve seats within the ceramic firedeck, fabrication of cast-in-place ceramic port liners, implementation of vapor phase lubrication, and elimination of the engine coolant system. Silicon nitride valves were successfully developed to meet several production abuse test requirements and incorporated into the test bed with a ceramic valve guide and solid film lubrication. The ADECD cylinder head features ceramic port shields to increase insulation and exhaust energy recovery. The combustion chamber includes a ceramic firedeck and piston cap. The tribological challenge posed by top ring reversal temperatures of 550 C was met through the development of vapor phase lubrication using tricresyl phosphate at the ring-liner interface. A solenoid-controlled, variable valve actuation system

  19. Advanced diesel engine component development program, tasks 4-14

    Science.gov (United States)

    Kaushal, Tony S.; Weber, Karen E.

    1994-11-01

    This report summarizes the Advanced Diesel Engine Component Development (ADECD) Program to develop and demonstrate critical technology needed to advance the heavy-duty low heat rejection engine concept. Major development activities reported are the design, analysis, and fabrication of monolithic ceramic components; vapor phase and solid film lubrication; electrohydraulic valve actuation; and high pressure common rail injection. An advanced single cylinder test bed was fabricated as a laboratory tool in studying these advanced technologies. This test bed simulates the reciprocator for a system having no cooling system, turbo compounding, Rankine bottoming cycle, common rail injection, and variable valve actuation to achieve fuel consumption of 160 g/kW-hr (.26 lb/hp-hr). The advanced concepts were successfully integrated into the test engine. All ceramic components met their functional and reliability requirements. The firedeck, cast-in-place ports, valves, valve guides, piston cap, and piston ring were made from silicon nitride. Breakthroughs required to implement a 'ceramic' engine included the fabrication of air-gap cylinder heads, elimination of compression gaskets, machining of ceramic valve seats within the ceramic firedeck, fabrication of cast-in-place ceramic port liners, implementation of vapor phase lubrication, and elimination of the engine coolant system. Silicon nitride valves were successfully developed to meet several production abuse test requirements and incorporated into the test bed with a ceramic valve guide and solid film lubrication. The ADECD cylinder head features ceramic port shields to increase insulation and exhaust energy recovery. The combustion chamber includes a ceramic firedeck and piston cap. The tribological challenge posed by top ring reversal temperatures of 550 C was met through the development of vapor phase lubrication using tricresyl phosphate at the ring-liner interface. A solenoid-controlled, variable valve actuation system

  20. Active Learning and Reflection in Product Development Engineering Education

    Science.gov (United States)

    Shekar, Aruna

    2007-01-01

    Traditional engineering courses at tertiary level have been traditionally theory-based, supported by laboratory work, but there is now a world-wide trend towards project-based learning. In product development education, project-based learning is essential in order to integrate the disciplines of design, marketing and manufacturing towards the…

  1. International Trade as an Engine of Growth in Developing Countries ...

    African Journals Online (AJOL)

    This study examines international trade as an engine of growth in developing countries, a case study of Nigeria. A review of the literature reveals that countries that are more open to international trade tends to experience higher growth rate and per-capital income than countries who do not trade or closed economy.

  2. Engineering development of advanced froth flotation. Volume 2, Final report

    Energy Technology Data Exchange (ETDEWEB)

    Ferris, D.D.; Bencho, J.R.; Torak, E.R. [ICF Kaiser Engineers, Inc., Pittsburgh, PA (United States)

    1995-03-01

    This report is an account of findings related to the Engineering and Development of Advanced Froth Flotation project. The results from benchscale and proof-of-concept (POC) level testing are presented and the important results from this testing are used to refine a conceptual design and cost estimate for a 20 TPH Semi-Works Facility incorporating the final proposed technology.

  3. Examining engineering costs for development of highway projects.

    Science.gov (United States)

    2012-12-01

    The Texas Department of Transportation (TxDOT) commissioned a research team at Texas State University-San Marcos Department of Accounting to analyze the cost of projects by determining the cost of a preliminary engineering hour necessary to develop h...

  4. Development of the Scale for "Convergence Thinking" in Engineering

    Science.gov (United States)

    Park, Sungmi

    2016-01-01

    Purpose: The purpose of this paper is to define the concept of "convergence thinking" as a trading zone for knowledge fusion in the engineering field, and develops its measuring scale. Design/ Methodology/Approach: Based on results from literature review, this study clarifies a theoretical ground for "convergence thinking."…

  5. Integration of Sustainable Development in Sanitary Engineering Education in Sweden

    Science.gov (United States)

    Rydhagen, B.; Dackman, C.

    2011-01-01

    In the Swedish Act for higher education, as well as in the policies of technical universities, it is stated that sustainable development (SD) should be integrated into engineering education. Researchers argue that SD needs to be integrated into the overall course content rather than added as a specific course. In this paper, six engineering…

  6. Engineering development testing of the GPHS-RTG converter

    International Nuclear Information System (INIS)

    Cockfield, R.D.

    1981-01-01

    The GPHS-RTG will provide electrical power for the Galileo orbiter and for the two spacecraft of the International Solar Polar Mission. The GPHS-RTG consists of two primary assemblies: the General Purpose Heat Source, and the converter. This paper deals only with the converter, and highlights engineering tests that provide support for its design development

  7. Engineering Education for Agricultural and Rural Development in Africa

    Science.gov (United States)

    Adewumi, B. A.

    2008-01-01

    Agricultural Engineering has transformed agricultural practices from subsistence level to medium and large-scale production via mechanisation in the developed nations. This has reduced the labour force requirements in agriculture; increased production levels and efficiency, product shelf life and product quality; and resulted into…

  8. Development of Management Methodology for Engineering Production Quality

    Science.gov (United States)

    Gorlenko, O.; Miroshnikov, V.; Borbatc, N.

    2016-04-01

    The authors of the paper propose four directions of the methodology developing the quality management of engineering products that implement the requirements of new international standard ISO 9001:2015: the analysis of arrangement context taking into account stakeholders, the use of risk management, management of in-house knowledge, assessment of the enterprise activity according to the criteria of effectiveness

  9. Development of Desktop Computing Applications and Engineering Tools on GPUs

    DEFF Research Database (Denmark)

    Sørensen, Hans Henrik Brandenborg; Glimberg, Stefan Lemvig; Hansen, Toke Jansen

    (GPUs) for high-performance computing applications and software tools in science and engineering, inverse problems, visualization, imaging, dynamic optimization. The goals are to contribute to the development of new state-of-the-art mathematical models and algorithms for maximum throughout performance...

  10. Interdisciplinary Research for Engineering Skills Development Interdisciplinary Research for Engineering Skills Development

    Directory of Open Access Journals (Sweden)

    Angel E. González-Lizardo

    2012-02-01

    Full Text Available Este trabajo reporta los resultados de una experiencia interdisciplinaria de investigaciónpara estudiantes de ingeniería, en el Laboratorio de Ingeniería de Plasma (PEL por sussiglas en inglés de la Universidad Politécnica de Puerto Rico (UPPR. Los rasgos fuertes de esta experiencia y su relación con los resultados esperados por la Junta de Acreditación para Ingeniería y Tecnología (ABET por sus siglas en inglés son destacados, y una descripción cualitativa de los resultados en términos de la ejecución de los estudiantes durante la experiencia y después de ella. Se presenta un ejemplo de las diferentes actividades realizadas por un equipo de estudiantes subgraduados y su relación con los resultados esperados por ABET. La experiencia de investigación en el PEL provee a los estudiantes con una oportunidad única para practicar la ingeniería antes de su graduación, a través de problemas reales, innovación, colaboración con otras instituciones, y presentación de su trabajo a audiencias de científicos e ingenieros. This work reports the results of an ad hoc interdisciplinary research experience for undergraduate engineering students at the Plasma Engineering Laboratory (PEL of the Polytechnic University of Puerto Rico (PUPR. The strong features of this experience and their relationship with Accreditation Board for Engineering and Technology (ABET outcomes are pointed out, and a qualitative description of the results is discussed, in terms of the performance of the students during the experience and after it. An example of the different activities performed by a team of undergraduate students, and their relationship with the ABET outcomes is presented. The undergraduate research at the PEL provides the students with a unique opportunity to practice engineering before graduation through real life problems, innovation, collaboration with other institutions, and presentation of their work for engineering and scientific audiences.

  11. Large-scale lysimeter site St. Arnold, Germany: analysis of 40 years of precipitation, leachate and evapotranspiration

    Directory of Open Access Journals (Sweden)

    N. Harsch

    2009-03-01

    Full Text Available This study deals with a lysimetrical-meteorological data series collected on the large-scale lysimeter site "St. Arnold", Germany, from November 1965 to April 2007. The particular relevance of this data rests both upon its perdurability and upon the fact that the site is comprised of a grassland basin, an oak/beech and a pine basin.

    Apart from analyzing long term trends of the meteorological measurements, the primary objective of this study is to investigate the water balance in grassland and forested basins, in particular comparing the precipitation term to leachate quantities and potential and actual evapotranspiration. The latter are based upon the Penman and the Penman-Monteith approaches, respectively.

    The main results of this survey are that, on a long-term average, the grassland basin turns more than half (53% of its annually incoming precipitation into leachate and only 36% into water vapour, while the deciduous forest exhibits a ratio of 37% for leachate and 56% for evapotranspiration, and the evergreen coniferous forest shows the highest evaporation rate (65% and the lowest leachate rate (26%.

    Concerning these water balances, considerable differences both between basins and between seasons stand out. While summer periods exhibit high evapotranspiration rates for the forests and moderate ones for the grassland, winter periods are characterised by considerable leachate quantities for grassland and the deciduous forest and moderate ones for the coniferous forest. Following the analysis of the climatic development in St. Arnold, trends towards a milder and more humid regional climate were detected.

  12. Development of a Thermoacoustic Stirling Engine Technology Demonstrator

    Science.gov (United States)

    Reissner, Alexander; Gerger, Joachim; Hummel, Stefan; Reißig, Jannis; Pawelke, Roland

    2014-08-01

    Waste heat is a primary source of energy loss in many aerospace and terrestrial applications. FOTEC, an Austrian Research Company located in Wiener Neustadt, is presently developing a micro power converter, promising high efficiencies even for small- scale applications. The converter is based on an innovative thermoacoustic stirling engine concept without any moving parts. Such a maintenance-free engine system would be particularly suitable for advanced space power systems (radioisotope, waste heat) or even within the scope of terrestrial energy harvesting. This paper will summarizes the status of our ongoing efforts on this micro power converter technology.

  13. Development of a Multimedia Toolkit for Engineering Graphics Education

    Directory of Open Access Journals (Sweden)

    Moudar Zgoul

    2009-09-01

    Full Text Available This paper focuses upon the development of a multimedia toolkit to support the teaching of Engineering Graphics Course. The project used different elements for the toolkit; animations, videos and presentations which were then integrated in a dedicated internet website. The purpose of using these elements is to assist the students building and practicing the needed engineering skills at their own pace as a part of an e-Learning solution. Furthermore, this kit allows students to repeat and view the processes and techniques of graphical construction, and visualization as much as needed, allowing them to follow and practice on their own.

  14. Upgrades of Hanford Engineering Development Laboratory hot cell facilities

    International Nuclear Information System (INIS)

    Daubert, R.L.; DesChane, D.J.

    1987-01-01

    The Hanford Engineering Development Laboratory operates the 327 Postirradiation Testing Laboratory (PITL) and the 324 Shielded Materials Facility (SMF). These hot cell facilities provide diverse capabilities for the postirradiation examination and testing of irradiated reactor fuels and materials. The primary function of these facilities is to determine failure mechanisms and effects of irradiation on physical and mechanical properties of reactor components. The purpose of this paper is to review major equipment and facility upgrades that enhance customer satisfaction and broaden the engineering capabilities for more diversified programs. These facility and system upgrades are providing higher quality remote nondestructive and destructive examination services with increased productivity, operator comfort, and customer satisfaction

  15. Development of GE90 engine with largest thrust. GE90 engine no kaihatsu jokyo

    Energy Technology Data Exchange (ETDEWEB)

    Aono, H [Ishikawajima-Harima Heavy Industries, Co. Ltd., Tokyo (Japan)

    1994-05-01

    The present paper explained the turbofan engine GE90 which is being developed by General Electric Co., USA. That engine is to meet the thrust (takeoff thrust) of 300 to 530kN as required for the new-generation wide-fuselage civil transport plane which is being designed for its planned operation in the 1990's. In April, 1991, the world's strongest thrust of 480kN was achieved with engine elements also confirmed through element test. Thereafter, the engine underwent a flying test on board of Boeing 747 to materialize the planned operation in 1995. Made to be 9 in by-pass ratio and about 40 in overall pressure ratio, the GE90 was given the concept that advantage could be secured in both propulsive efficiency and thermal efficiency. That concept could be materialized by the development of composite fan blade technology and energy-efficient technology which were both demonstrated with an unducted fan. In spite of its pressure ratio of 22, the GE90's high pressure compressor demonstrates its polytropic efficiency which is equal to that of the low pressure ratio compressor. 3 refs., 19 figs., 1 tab.

  16. Development Trends of Cartography and Geographic Information Engineering

    Directory of Open Access Journals (Sweden)

    WANG Jiayao

    2010-04-01

    Full Text Available Aimed at the problems of cartography and geographic information engineering and increasing demands of national and military infomationization construction, the paper proposes six hotspots on the research of cartography and geographic information engineering for the future on the foundation of analyzing the development track of cartology, which are heterogeneous geospatial data assimilation, transferring from emphasizing geography infor-mation gaining to user-oriented geographic information deep processing, web or grid geographic information service. intelligent spatial data generalization. integration of GIS and VGE. cartography and geographic information engineering theory system with multi-mode(Map,.GlS..VGE spatial-temporal integrated cognition as the core. And discusses the necessity ,existing groundwork and research contents on studying these hotspots.

  17. Automotive Stirling engine development program. [fuel economy assessment

    Science.gov (United States)

    Kitzner, E. W.

    1978-01-01

    The Ford/DOE automotive Stirling engine development program is directed towards establishing the technological and developmental base that would enable a decision on whether an engineering program should be directed at Stirling engine production. The fuel economy assessment aims to achieve, with a high degree of confidence, the ERDA proposal estimate of 20.6 MPG (gasoline) for a 4500 lb 1WC Stirling engine passenger car. The current M-H fuel economy projection for the 170 HP Stirling engine is 15.7 MPG. The confidence level for this projection is 32%. A confidence level of 29% is projected for a 22.1 MPG estimate. If all of the planned analyses and test work is accomplished at the end of the one year effort, and the projected improvements are substantiated, the confidence levels would rise to 59% for the 20.6 MPG projection and 54% for the 22.1 MPG projection. Progress achieved thus far during the fuel economy assessment is discussed.

  18. Unique Education and Workforce Development for NASA Engineers

    Science.gov (United States)

    Forsgren, Roger C.; Miller, Lauren L.

    2010-01-01

    NASA engineers are some of the world's best-educated graduates, responsible for technically complex, highly significant scientific programs. Even though these professionals are highly proficient in traditional analytical competencies, there is a unique opportunity to offer continuing education that further enhances their overall scientific minds. With a goal of maintaining the Agency's passionate, "best in class" engineering workforce, the NASA Academy of Program/Project & Engineering Leadership (APPEL) provides educational resources encouraging foundational learning, professional development, and knowledge sharing. NASA APPEL is currently partnering with the scientific community's most respected subject matter experts to expand its engineering curriculum beyond the analytics and specialized subsystems in the areas of: understanding NASA's overall vision and its fundamental basis, and the Agency initiatives supporting them; sharing NASA's vast reservoir of engineering experience, wisdom, and lessons learned; and innovatively designing hardware for manufacturability, assembly, and servicing. It takes collaboration and innovation to educate an organization that possesses such a rich and important historyand a future that is of great global interest. NASA APPEL strives to intellectually nurture the Agency's technical professionals, build its capacity for future performance, and exemplify its core valuesalJ to better enable NASA to meet its strategic visionand beyond.

  19. Biomedical engineering education in developing countries: research synthesis.

    Science.gov (United States)

    Douglas, Tania S

    2011-01-01

    Biomedical engineering (BME) contributes to development through improving human health. This paper examines BME education to address the needs of developing countries. Components of different BME programs described in the literature are synthesized to represent what has been proposed or implemented for the production of graduates able to address health problems in a manner suited to the local environment in which they occur. Published research on BME education is reviewed with reference to problem context, interventions and their mechanisms, and intended outcomes.

  20. TECHNOLOGICAL CONTRIBUTIONS OF THE MILITARY ENGINEERING TO THE NATIONAL DEVELOPMENT

    OpenAIRE

    RODRIGO CARO DE KARTZOW

    2018-01-01

    The development of the Chilean military industry is closely related to the growing of the national industry. Similarly to the way the history of the Army and the country are tightly related, the history of the military engineering is an example of organic growth when compared to its civilian counterpart. Collaboration instead of competition is the distinctive seal that best shows the development of weaponry, explosives, cartography and nuclear power. This collaboration have lasted with the ye...

  1. Development of System Engineering Technology for Nuclear Fuel Cycle

    International Nuclear Information System (INIS)

    Kim, Ho Dong; Kim, Sung Ki; Song, Kee Chan

    2010-04-01

    This report is aims to establish design requirements for constructing mock-up system of pyroprocess by 2011 to realize long-term goal of nuclear energy promotion comprehensive plan, which is construction of engineering scale pyroprocess integrated process demonstration facility. The development of efficient process for spent fuel and establishment of system engineering technology to demonstrate the process are required to develop nuclear energy continuously. The detailed contents of research for these are as follows; - Design of Mock-up facility for demonstrate pyroprocess, Construction, Approval, Trial run, Performance test - Development of nuclear material accountancy technology for unit processes of pyroprocess and design of safeguards system - Remote operation of demonstrating pyroprocess / Development of maintenance technology and equipment - Establishment of transportation system and evaluation of pre-safety for interim storage system - Deriving and implementation of a method to improve nuclear transparency for commercialization proliferation resistance nuclear fuel cycle Spent fuel which is the most important pending problem of nuclear power development would be reduced and recycled by developing the system engineering technology of pyroprocess facility by 2010. This technology would contribute to obtain JD for the use of spent fuel between the ROK-US and to amend the ROK-US Atomic Energy Agreement scheduled in 2014

  2. Arnold Rüütel: meie küla käis käest kätte / Arnold Rüütel ; intervjueerinud Enno Tammer

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2005-01-01

    President Arnold Rüütel Teise maailmasõjaga seotud mälestustest, Molotov-Ribbentropi paktist, Moskvas võidupüha tähistamisel mitteosalemise põhjustest ja 2006. a. presidendivalimistel osalemisest

  3. Data Mining and Optimization Tools for Developing Engine Parameters Tools

    Science.gov (United States)

    Dhawan, Atam P.

    1998-01-01

    This project was awarded for understanding the problem and developing a plan for Data Mining tools for use in designing and implementing an Engine Condition Monitoring System. Tricia Erhardt and I studied the problem domain for developing an Engine Condition Monitoring system using the sparse and non-standardized datasets to be available through a consortium at NASA Lewis Research Center. We visited NASA three times to discuss additional issues related to dataset which was not made available to us. We discussed and developed a general framework of data mining and optimization tools to extract useful information from sparse and non-standard datasets. These discussions lead to the training of Tricia Erhardt to develop Genetic Algorithm based search programs which were written in C++ and used to demonstrate the capability of GA algorithm in searching an optimal solution in noisy, datasets. From the study and discussion with NASA LeRC personnel, we then prepared a proposal, which is being submitted to NASA for future work for the development of data mining algorithms for engine conditional monitoring. The proposed set of algorithm uses wavelet processing for creating multi-resolution pyramid of tile data for GA based multi-resolution optimal search.

  4. Diesel engine development in view of reduced emission standards

    International Nuclear Information System (INIS)

    Knecht, Walter

    2008-01-01

    Diesel engine development for use in light-, medium- and heavy-duty road vehicles is mainly driven by more and more stringent emission standards. Apart from air quality related emissions such as nitrogen oxides and particulates, also greenhouse gas (GHG) emissions are likely to become of more and more importance. Furthermore, oil-based fuel availability might become a problem due to limited reserves or due to political influences which leads to significantly increased fuel costs. Based on the above aspects, advanced engine technologies become essential and are discussed. Fuel injection with rate shaping capability and elevated injection pressures, air handling systems to increase the brake mean effective pressures (BMEPs) and specific power with a downsizing approach, while retaining a good dynamic response using possibly two-stage turbocharging. Heterogeneous and near-homogeneous combustion processes where the latter could possibly reduce the requirements on the exhaust gas aftertreatment system. Improvement and further development of engine management and control systems, exhaust gas aftertreatment for a reduction of nitrogen oxides and especially particulates and last but not least, energy recovery from the exhaust gas. Furthermore, alternative fuel usage in road vehicles is becoming important and their application in internal combustion engines is discussed

  5. President Arnold Rüütel: Eestis on alanud valimiste eelne sisepoliitiline võitlus / Arnold Rüütel ; intervjueerinud Urmo Soonvald

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2005-01-01

    President Arnold Rüütel vastab küsimustele, mis puudutavad tema kohtumist Venemaa presidendi Vladimir Putiniga, Eesti-Vene piirilepingule allakirjutamist, Läti presidendi Vaira Vike-Freiberga otsust sõita 9. maiks Moskvasse, välisministeeriumiga seotud skandaali, poliitikute selgitusi riigisaladuse ümber tekkinud skandaali kohta, erakorralisi valimisi kui võimalikku lahendust praegusele sisepoliitilisele olukorrale, Eesti välisministri puudumist Brüsselis toimuval kohtumisel USA presidendiga, kohtumist välisministrikandidaat Rein Langiga

  6. Development of engineering identity in the engineering curriculum in Dutch higher education : an explorative study from the teaching staff perspective

    NARCIS (Netherlands)

    Dehing, A.J.M.; Baartman, L.K.J.; Jochems, W.M.G.

    2013-01-01

    How do engineering students develop a professional identity during the course of the curriculum? What are the development mechanisms and important conditions? In an exploratory study among teachers the authors tried to find out whether the development of engineering identity can be understood by

  7. Development of System Engineering Technology for Nuclear Fuel Cycle

    International Nuclear Information System (INIS)

    Kim, Hodong; Choi, Iljae

    2013-04-01

    The development of efficient process for spent fuel and establishment of system engineering technology to demonstrate the process are required to develop nuclear energy continuously. The demonstration of pyroprocess technology which is proliferation resistance nuclear fuel cycle technology can reduce spent fuel and recycle effectively. Through this, people's trust and support on nuclear power would be obtained. Deriving the optimum nuclear fuel cycle alternative would contribute to establish a policy on back-end nuclear fuel cycle in the future, and developing the nuclear transparency-related technology would contribute to establish amendments of the ROK-U. S. Atomic Energy Agreement scheduled in 2014

  8. Software Engineering Research/Developer Collaborations in 2004 (C104)

    Science.gov (United States)

    Pressburger, Tom; Markosian, Lawrance

    2005-01-01

    In 2004, six collaborations between software engineering technology providers and NASA software development personnel deployed a total of five software engineering technologies (for references, see Section 7.2) on the NASA projects. The main purposes were to benefit the projects, infuse the technologies if beneficial into NASA, and give feedback to the technology providers to improve the technologies. Each collaboration project produced a final report (for references, see Section 7.1). Section 2 of this report summarizes each project, drawing from the final reports and communications with the software developers and technology providers. Section 3 indicates paths to further infusion of the technologies into NASA practice. Section 4 summarizes some technology transfer lessons learned. Section 6 lists the acronyms used in this report.

  9. Nuclear Plant Analyzer development at the Idaho National Engineering Laboratory

    International Nuclear Information System (INIS)

    Laats, E.T.

    1986-10-01

    The Nuclear Plant Analyzer (NPA) is a state-of-the-art safety analysis and engineering tool being used to address key nuclear power plant safety issues. Under the sponsorship of the US Nuclear Regulatory Commission (NRC), the NPA has been developed to integrate the NRC's computerized reactor behavior simulation codes such as RELAP5, TRAC-BWR and TRAC-PWR, with well-developed computer color graphics programs and large repositories of reactor design and experimental data. An important feature of the NPA is the capability to allow an analyst to redirect a RELAP5 or TRAC calculation as it progresses through its simulated scenario. The analyst can have the same power plant control capabilities as the operator of an actual plant. The NPA resides on the dual Control Data Corporation Cyber 176 mainframe computers at the Idaho National Engineering Laboratory and Cray-1S computers at the Los Alamos National Laboratory (LANL) and Kirtland Air Force Weapons Laboratory (KAFWL)

  10. An engineering design network for SSC detector development

    International Nuclear Information System (INIS)

    DiGiacomo, N.J.

    1990-01-01

    The detector systems that are being proposed to exploit the capabilities of the SSC are of a scale and scope that will make them among the most complex devices ever built. To successfully design and build these systems over the next decade, the authors must make use of integrated state of the art computer aided engineering and design (CAE/CAD) tools that have been developed and employed in industry. The challenge is to made these tools and associated engineering resources available to the spectrum of institutions - large and small universities, industries and national labs - involved in SSC detector development in such a way that each may contribute and participate in the most effective manner. The authors believe that powerful workstations running sophisticated modeling, analysis and simulation software, linked by high speed data networks and governed by modern configuration management methods offer the ideal means of arriving at the optimum detector configuration for physics at the SSC

  11. Object oriented development of engineering software using CLIPS

    Science.gov (United States)

    Yoon, C. John

    1991-01-01

    Engineering applications involve numeric complexity and manipulations of a large amount of data. Traditionally, numeric computation has been the concern in developing an engineering software. As engineering application software became larger and more complex, management of resources such as data, rather than the numeric complexity, has become the major software design problem. Object oriented design and implementation methodologies can improve the reliability, flexibility, and maintainability of the resulting software; however, some tasks are better solved with the traditional procedural paradigm. The C Language Integrated Production System (CLIPS), with deffunction and defgeneric constructs, supports the procedural paradigm. The natural blending of object oriented and procedural paradigms has been cited as the reason for the popularity of the C++ language. The CLIPS Object Oriented Language's (COOL) object oriented features are more versatile than C++'s. A software design methodology based on object oriented and procedural approaches appropriate for engineering software, and to be implemented in CLIPS was outlined. A method for sensor placement for Space Station Freedom is being implemented in COOL as a sample problem.

  12. Cryogenic Propellant Storage and Transfer Engineering Development Unit Hydrogen Tank

    Science.gov (United States)

    Werkheiser, Arthur

    2015-01-01

    The Cryogenic Propellant Storage and Transfer (CPST) project has been a long-running program in the Space Technology Mission Directorate to enhance the knowledge and technology related to handling cryogenic propellants, specifically liquid hydrogen. This particular effort, the CPST engineering development unit (EDU), was a proof of manufacturability effort in support of a flight article. The EDU was built to find and overcome issues related to manufacturability and collect data to anchor the thermal models for use on the flight design.

  13. Development of catalyst for diesel engine; Diesel engine yo shokubai no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Ueno, H; Furutani, T; Nagami, T [Toyota Motor Corp., Aichi (Japan); Aono, N; Goshima, H; Kasahara, K [Cataler Industrial Co. Ltd., Shizuoka (Japan)

    1997-10-01

    The new concept catalyst for diesel engine has been developed. When the exhaust temperature is low, SOF and HC are temporarily adsorbed by the adsorbent within the catalyst and are oxidized as the temperature rise. The process of this development have manifested as follows. (1) The coating material is important factor to govern the oxidation activity. (2) SOF is reduced by the coating material in low temperature less than 200degC. (3) The coating material, which has low SO2 adsorbing rate suppress the sulfate formation at high temperature. 2 refs., 11 figs., 1 tab.

  14. [Demise of the wound physician vocation exemplified by the political representative Arnold Schlegel (1850-1924)].

    Science.gov (United States)

    Gross, D

    1996-01-01

    The name of Arnold Schlegel stands for a dazzling and complex personality. After being apprenticed to a barber surgeon in Württemberg, he spent about four decades in Switzerland working as an innkeeper. Yet, Schlegel distinguished himself as one of the leading representatives of the last non-academic surgeons in Württemberg. In contrast to most of his surgical colleagues, most of Schlegel's vocational activities are documented. This study is based on unpublished documents of different archives of Württemberg and Switzerland. The aim of the study is to illuminate the life of Arnold Schlegel and, in view of his policy, to illustrate the trying circumstances of contemporary barber surgery.

  15. President kutsub koostööle / Arnold Rüütel

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2002-01-01

    Ilmunud ka: Postimees (2002) 25. veebr., lk. 11, pealk.: Vajame uut ühiskondlikku lepet; SL Õhtuleht (2002) 25. veebr., lk. 10, pealk.: Aeg rahvuslikuks leppeks, vt. samas karikatuur; Virumaa Teataja (2002) 26. veebr., lk. 7, pealk.: Eestis tuleb taastada sotsiaalne tasakaal; Maaleht (2002) 28. veebr., lk. 8, pealk.: Uhkus ajab upakile; Põhjarannik (2002) 26. veebr., lk. 5, pealk.: President Arnold Rüütli kõne Eesti Vabariigi 84. aastapäeval; Severnoje Poberezhje (2002) 26. veebr., lk. 5; Meie Maa (2002) 26. veebr., lk. 2, pealk.: Vajame põlvkondlikku järjepidevust ja uut ühiskondlikku lepet. President Arnold Rüütli kõne Eesti Vabariigi 84. aastapäeval Estonia teatris 24. veebruaril 2002. Lühendatult

  16. Arnold tongues and the Devil's Staircase in a discrete-time Hindmarsh–Rose neuron model

    International Nuclear Information System (INIS)

    Felicio, Carolini C.; Rech, Paulo C.

    2015-01-01

    We investigate a three-dimensional discrete-time dynamical system, described by a three-dimensional map derived from a continuous-time Hindmarsh–Rose neuron model by the forward Euler method. For a fixed integration step size, we report a two-dimensional parameter-space for this system, where periodic structures, the so-called Arnold tongues, can be seen with periods organized in a Farey tree sequence. We also report possible modifications in this parameter-space, as a function of the integration step size. - Highlights: • We investigate the parameter-space of a particular 3D map. • Periodic structures, namely Arnold tongues, can be seen there. • They are organized in a Farey tree sequence. • The map was derived from a continuous-time Hindmarsh–Rose neuron model. • The forward Euler method was used for such purpose.

  17. Émile Durkheim between Gabriel Tarde and Arnold van Gennep

    DEFF Research Database (Denmark)

    Thomassen, Bjørn

    2012-01-01

    This article will situate Durkheim's work by revisiting two debates that influenced his attempt to define and give direction to sociology and anthropology: the debates between Durkheim and Gabriel Tarde and the debates between Durkheim and Arnold van Gennep. The battle between Tarde and Durkheim...... has in recent years been the object of several conferences and publications. This has happened alongside a much needed Tarde revival in sociology. However, Tarde was only one of Durkheim's opponents. For a long period, following Tarde's death in 1904, Arnold van Gennep represented the strongest...... critique of Durkheim's project. This ‘debate’ is little known among anthropologists and social scientists. The aim of this article is to situate Durkheim and the birth of the social sciences in France between both of these two figures. The aim is therefore also to bring together two disciplinary debates...

  18. President Rüütel's speech at UN / Arnold Rüütel

    Index Scriptorium Estoniae

    Rüütel, Arnold

    2004-01-01

    President Arnold Rüütli 22. septembril New Yorgis ÜRO peaassamblee 59. istungjärgu peadebatil peetud kõne, milles ta keskendus ÜRO aastatuhande deklaratsioonis sõnastatud eesmärkide täitmise ja digitaalse lõhe ületamise võimalustele ning põlisrahvaste õiguste kaitsele. Töövisiit New Yorki 19.-24.09.2004

  19. Presidendi kõne Eesti Vabariigi 87. aastapäeval / Arnold Rüütel

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2005-01-01

    Ilmunud ka: Teataja : Eestimaa Rahvaliidu Ajaleht (2005) märts, nr. 3, lk. 1 ; Narva Postiljon (2005) 26. veebr.. lk. 2 ; SL Õhtuleht (2005) 25. veebr. (lüh.) ; Narva Postiljon (2005) 25. veebr. (lüh.). President Arnold Rüütli kõne 24. veebruaril Estonia teatrisaalis. Presidendi sõnul peab Eesti edasine areng olema tasakaalustatud

  20. Eestit peab esindama Moskvas valitsuse liige / Arnold Rüütel

    Index Scriptorium Estoniae

    Rüütel, Arnold

    2005-01-01

    Ilmunud ka Järva Teataja (2005/Mar/8) lk. 2 ; Põhjarannik (2005/Mar/8) lk. 2 ; Severnoje Poberezhje (2005/Mar/8) lk. 2 ; Vooremaa (2005/Mar/10) lk. 2 ; Harjumaa (2005/Mar/11) lk. 2. President Arnold Rüütli avaldus 7. märtsil 2005, milles ta teatab oma otsusest mitte vastu võtta kutset osaleda selle aasta 9. mail Suures Isamaasõjas saavutatud võidu 60. aastapäeva pidustustel Moskvas

  1. President : olen sügavas mures / Arnold Rüütel ; interv. Toomas Sildam

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2006-01-01

    President Arnold Rüütel nendib, et oma uusaastaläkituses noorte probleemidest Eesti ühiskonnas kõneldes ei teadnud ta, et samad probleemid puudutavad teravalt ka ta oma tütretütreid. Lisa: Lossiskandaal. Vt. samas: Ihukaitsjad vaikivad Rüütli eraelust; Ingvar Bärenklau. Rüütli lapselapsed elavad Kadriorus juba aastaid; Arvamust avaldavad Andrus Ansip, Urmas Reinsalu, Andres Herkel, Ain Seppik, Jaanus Männik ja Ivari Padar

  2. Basic stages in the development of the theory of Ramjet Engines (RJE)

    Science.gov (United States)

    Merkulov, I. A.

    1977-01-01

    Basic periods in the history of the development of ramjet engine theory are cited. The periods include the first experimental tests as well as the development of basic ideas and theoretical development of the cosmic ramjet engine.

  3. Translation of the V. I. Arnold paper "From Superpositions to KAM Theory" (Vladimir Igorevich Arnold. Selected — 60, Moscow: PHASIS, 1997, pp. 727-740)

    Science.gov (United States)

    Sevryuk, Mikhail B.

    2014-11-01

    V. I. Arnold (12 June 1937-3 June 2010) published several papers where he described, in the form of recollections, his two earliest research problems (superpositions of continuous functions and quasi-periodic motions in dynamical systems), the main results and their interrelations: [A1], then [A2] (reprinted as [A4, A6]), and [A3] (translated into English by the author as [A5]). The first exposition [A1] has never been translated into English; however, it contains many details absent in the subsequent articles. It seems therefore that publishing the English translation of the paper [A1] would not be superfluous. What follows is this translation. In many cases, the translator gives complete bibliographic descriptions of various papers mentioned briefly in the original Russian text. The English translations of papers in Russian are also pointed out where possible. A related material is contained also in Arnold's recollections "On A.N. Kolmogorov". Slightly different versions of these reminiscences were published several times in Russian and English [A7-A12]. The early history of KAM theory is also discussed in detail in the recent brilliant semi-popular book [A13].

  4. Engineering Competencies in International Development Co-operation - the Case of Capacity Development in Environment (CDE)

    DEFF Research Database (Denmark)

    Wangel, Arne

    2001-01-01

    The focus of the paper is the need for engineers to develop new competencies, when they are involved in international development cooperation. Drawing on the case of the Post-RIO strategy of capacity development in environment in developing countries, the paper reviews a recent response...... of such courses, which give emphasis to local views on institutional development and policy change. engineers from industrialised countries have a long tradition of working in the third world: building infrastructure to facilitate exports of raw materials during colonial times; implementing development aid...... on the transfer of managerial models across cultures, on how to develop inter-cultural competence in management, and on the significance of differences in engineering and industrial culture. Second, the concepts of dynamic assimilation and local learning processes and their implications for the practicing...

  5. Biomedical engineering tasks. [electrode development for electrocardiography and electroencephalography

    Science.gov (United States)

    1972-01-01

    Electrocardiographic and vectorcardiographic bioinstrumentation work centered on the development of a new electrode system harness for Project Skylab. Evaluation of several silver electrode configurations proved superior impedance voltage performance for silver/silver chloride electrodes mounted flush by using a paste adhesive. A portable ECG processor has been designed and a breadboard unit has been built to sample ECG input data at a rate of 500 samples per second for arrhythmia detection. A small real time display driver program has been developed for statistical analysis on selected QPS features. Engineering work on a sleep monitoring cap assembly continued.

  6. Advanced Vibration Analysis Tool Developed for Robust Engine Rotor Designs

    Science.gov (United States)

    Min, James B.

    2005-01-01

    The primary objective of this research program is to develop vibration analysis tools, design tools, and design strategies to significantly improve the safety and robustness of turbine engine rotors. Bladed disks in turbine engines always feature small, random blade-to-blade differences, or mistuning. Mistuning can lead to a dramatic increase in blade forced-response amplitudes and stresses. Ultimately, this results in high-cycle fatigue, which is a major safety and cost concern. In this research program, the necessary steps will be taken to transform a state-of-the-art vibration analysis tool, the Turbo- Reduce forced-response prediction code, into an effective design tool by enhancing and extending the underlying modeling and analysis methods. Furthermore, novel techniques will be developed to assess the safety of a given design. In particular, a procedure will be established for using natural-frequency curve veerings to identify ranges of operating conditions (rotational speeds and engine orders) in which there is a great risk that the rotor blades will suffer high stresses. This work also will aid statistical studies of the forced response by reducing the necessary number of simulations. Finally, new strategies for improving the design of rotors will be pursued.

  7. History of the Development of NERVA Nuclear Rocket Engine Technology

    International Nuclear Information System (INIS)

    David L., Black

    2000-01-01

    During the 17 yr between 1955 and 1972, the Atomic Energy Commission (AEC), the U.S. Air Force (USAF), and the National Aeronautics and Space Administration (NASA) collaborated on an effort to develop a nuclear rocket engine. Based on studies conducted in 1946, the concept selected was a fully enriched uranium-filled, graphite-moderated, beryllium-reflected reactor, cooled by a monopropellant, hydrogen. The program, known as Rover, was centered at Los Alamos Scientific Laboratory (LASL), funded jointly by the AEC and the USAF, with the intent of designing a rocket engine for long-range ballistic missiles. Other nuclear rocket concepts were studied during these years, such as cermet and gas cores, but are not reviewed herein. Even thought the program went through the termination phase in a very short time, the technology may still be fully recoverable/retrievable to the state of its prior technological readiness in a reasonably short time. Documents; drawings; and technical, purchasing, manufacturing, and materials specifications were all stored for ease of retrieval. If the U.S. space program were to discover a need/mission for this engine, its 1972 'pencils down' status could be updated for the technology developments of the past 28 yr for flight demonstration in 8 or fewer years. Depending on today's performance requirements, temperatures and pressures could be increased and weight decreased considerably

  8. Aero-methods and engineering research and development

    Energy Technology Data Exchange (ETDEWEB)

    Peterson, R K

    1979-01-01

    There is presently a sharp, ongoing increase in the volume of work being conducted throughout the country associated with the development of natural gas fields as well as the resulting accelerated development of major gas trunklines. Aero-methods have presently found wide application in the engineering and planning of equipment for such projects. Success has been obtained by the increased quantity and quality of the available engineering information: The ''Giprospetsgaz'' Institute is using aerial photography as the basis for selecting pipeline routes and to more accurately determine the equipment requirements along proposed trunklines such as for compressors, gas transfer stations, electrical power substations, worker settlements, water and transport infrastructure and communications. These requirements are the most important factors in reducing capital operating expenditures. The greatest savings, in economic terms, can be achieved by avoiding sparsely settled or uninhabited areas as much as possible. Similiarly, aerial photography coupled with computer application aids in the solution of engineering problems. Third-generation computers are recommended for this process.

  9. Development of a Systems Engineering Competency Model Tool for the Aviation and Missile Research, Development, And Engineering Center (AMRDEC)

    Science.gov (United States)

    2017-06-01

    grade level (GS-7 to GS-15). This foundational model is structured to support the individual needs of any Department of Defense organization and is... organizational level with traceability to the approved OPM competencies. The Redstone SECCM Tool will allow documentation of system engineering competencies and...assessment of individual and organizational development and training needs. This report documents the requirements analysis, system design, and system

  10. Effects of Engineering Design-Based Science on Elementary School Science Students' Engineering Identity Development across Gender and Grade

    Science.gov (United States)

    Capobianco, Brenda M.; Yu, Ji H.; French, Brian F.

    2015-04-01

    The integration of engineering concepts and practices into elementary science education has become an emerging concern for science educators and practitioners, alike. Moreover, how children, specifically preadolescents (grades 1-5), engage in engineering design-based learning activities may help science educators and researchers learn more about children's earliest identification with engineering. The purpose of this study was to examine the extent to which engineering identity differed among preadolescents across gender and grade, when exposing students to engineering design-based science learning activities. Five hundred fifty preadolescent participants completed the Engineering Identity Development Scale (EIDS), a recently developed measure with validity evidence that characterizes children's conceptions of engineering and potential career aspirations. Data analyses of variance among four factors (i.e., gender, grade, and group) indicated that elementary school students who engaged in the engineering design-based science learning activities demonstrated greater improvements on the EIDS subscales compared to those in the comparison group. Specifically, students in the lower grade levels showed substantial increases, while students in the higher grade levels showed decreases. Girls, regardless of grade level and participation in the engineering learning activities, showed higher scores in the academic subscale compared to boys. These findings suggest that the integration of engineering practices in the science classroom as early as grade one shows potential in fostering and sustaining student interest, participation, and self-concept in engineering and science.

  11. Development of computer aided engineering system for TRAC applications

    International Nuclear Information System (INIS)

    Arai, Kenji; Itoya, Seihiro; Uematsu, Hitoshi; Tsunoyama, Shigeaki

    1990-01-01

    An advanced best estimate computer program for nuclear reactor transient analysis, TRAC has been extensively used to carry out various thermal hydraulic calculations in the nuclear engineering field, because of its versatility. To perform efficiently a wide variety of TRAC calculation, the efficient utilization of computers and the convenient environment for input and output processing is necessary. We have applied a computer network comprising a super-computer, engineering work stations and personal computers to TRAC calculations and have assigned the appropriate functions to each computer. We have also been developing an interactive graphics system for input and output processing on an EWS. This hardware and software environment can improve the effectiveness of TRAC utilization for various thermal hydraulic calculations. (author)

  12. DEVELOPMENT AND TESTING OF A PRE-PROTOTYPE RAMGEN ENGINE

    Energy Technology Data Exchange (ETDEWEB)

    Aaron Koopman

    2003-07-01

    The research and development effort of a new kind of compressor and engine is presented. The superior performance of these two products arises from the superior performance of rotating supersonic shock-wave compression. Several tasks were performed in compliance with the DOE award objectives. A High Risk Technology review was conducted and evaluated by a team of 20 senior engineers and scientists representing various branches of the federal government. The conceptual design of a compression test rig, test rotors, and test cell adaptor was completed. The work conducted lays the foundation for the completed design and testing of the compression test rig, and the design of a supersonic shock-wave compressor matched to a conventional combustor and turbine.

  13. Turbofan Engine Core Compartment Vent Aerodynamic Configuration Development Methodology

    Science.gov (United States)

    Hebert, Leonard J.

    2006-01-01

    This paper presents an overview of the design methodology used in the development of the aerodynamic configuration of the nacelle core compartment vent for a typical Boeing commercial airplane together with design challenges for future design efforts. Core compartment vents exhaust engine subsystem flows from the space contained between the engine case and the nacelle of an airplane propulsion system. These subsystem flows typically consist of precooler, oil cooler, turbine case cooling, compartment cooling and nacelle leakage air. The design of core compartment vents is challenging due to stringent design requirements, mass flow sensitivity of the system to small changes in vent exit pressure ratio, and the need to maximize overall exhaust system performance at cruise conditions.

  14. Plant synthetic biology for molecular engineering of signalling and development.

    Science.gov (United States)

    Nemhauser, Jennifer L; Torii, Keiko U

    2016-03-02

    Molecular genetic studies of model plants in the past few decades have identified many key genes and pathways controlling development, metabolism and environmental responses. Recent technological and informatics advances have led to unprecedented volumes of data that may uncover underlying principles of plants as biological systems. The newly emerged discipline of synthetic biology and related molecular engineering approaches is built on this strong foundation. Today, plant regulatory pathways can be reconstituted in heterologous organisms to identify and manipulate parameters influencing signalling outputs. Moreover, regulatory circuits that include receptors, ligands, signal transduction components, epigenetic machinery and molecular motors can be engineered and introduced into plants to create novel traits in a predictive manner. Here, we provide a brief history of plant synthetic biology and significant recent examples of this approach, focusing on how knowledge generated by the reference plant Arabidopsis thaliana has contributed to the rapid rise of this new discipline, and discuss potential future directions.

  15. Human Factors Engineering: Current Practices and Development Needs in Finland

    Energy Technology Data Exchange (ETDEWEB)

    Savioja, Paula; Norros, Leena; Liinasuo, Marja; Laarni, Jari [VTT Technical Research Centre of Finland, Finland (Finland)

    2011-08-15

    This paper describes initial findings from a study concerning the practices and development needs of Human Factors Engineering (HFE) in Finland. HFE is increasing in importance as the Radiation and Nuclear Safety Authority Finland (STUK) is renewing the regulatory guidelines and the intention is to include requirements concerning HFE. The motivation for the paper is to discover how HFE is conducted currently in order to envision what should be aimed at when modifying requirements for design practices. In an interview with STUK it was discovered that current HFE practices encompass mainly activities related to control room modifications and as such namely verification and validation of new designs. The adoption of the entire HFE process in design and modification projects requires changes that include better integration of technical and Human Factors Engineering approaches. Boundary objects that mediate between different design disciplines are needed in order to enforce the stronger integration. Concept of operations (CONOPS) is suggested as a such boundary object.

  16. Developing engineering capabilities as a support to a nuclear program

    International Nuclear Information System (INIS)

    Rodriguez, A.G.

    1986-04-01

    The performance of a nuclear program needs a quite substantial and diversified volume of technological resources. Its integrated management is one of the basic aspects to be settled. In this regard, the creation of strong engineering organizations with the ability to develop management of the project technical activities as a whole has had success in various countries. These organizations should be provided with suitable means to rapidly assimilate the technology and should serve as a channel and support to local industry in general. The development of a nuclear program also requires the collaboration of other institutions, such as universities and research and development centers. In this sense, engineer and technician training necessities are important both in number and technological qualification, as is the availability of capacities in such different areas as simulation and advanced calculation, geology and soil mechanics, materials, fabrication processes, test laboratories, etc. The volume of technological activities to be developed in relation to a stable, although not necessarily large, nuclear program justifies in itself the assigning of important resources to all the above mentioned activities. However, it should be noted that it has been proved that the nuclear industry is completely pervious as regards other fields of activity. In fact, the more stringent quality requirements are quickly transmitted to other industrial processes, and the engineers trained in this area undergo a far from contemptible turnover towards non-nuclear activities. The basic research area in the nuclear field is not in itself a requirement that has to be in parallel with the development of a nuclear program. However, on medium and long-term bases, it may be interesting for a well balanced commercial program that research activities be established realistically and sensibly, even though short-term practical applications are not necessarily derived from this

  17. Software Development for EECU Platform of Turbofan Engine

    Science.gov (United States)

    Kim, Bo Gyoung; Kwak, Dohyup; Kim, Byunghyun; Choi, Hee ju; Kong, Changduk

    2017-04-01

    The turbofan engine operation consists of a number of hardware and software. The engine is controlled by Electronic Engine Control Unit (EECU). In order to control the engine, EECU communicates with an aircraft system, Actuator Drive Unit (ADU), Engine Power Unit (EPU) and sensors on the engine. This paper tried to investigate the process form starting to taking-off and aims to design the EECU software mode and defined communication data format. The software is implemented according to the designed software mode.

  18. Development of Advanced Carbon Face Seals for Aircraft Engines

    Science.gov (United States)

    Falaleev, S. V.; Bondarchuk, P. V.; Tisarev, A. Yu

    2018-01-01

    Modern aircraft gas turbine engines require the development of seals which can operate for a long time with low leakages. The basic type of seals applied for gas turbine engine rotor supports is face seal. To meet the modern requirements of reliability, leak-tightness and weight, low-leakage gas-static and hydrodynamic seals have to be developed. Dry gas seals use both gas-static and hydrodynamic principles. In dry gas seals microgrooves are often used, which ensure the reverse injection of leakages in the sealed cavity. Authors have developed a calculation technique including the concept of coupled hydrodynamic, thermal and structural calculations. This technique allows to calculate the seal performance taking into account the forces of inertia, rupture of the lubricant layer and the real form of the gap. Authors have compared the efficiency of seals with different forms of microgrooves. Results of calculations show that seal with rectangular form of microgrooves has a little gap leading to both the contact of seal surfaces and the wear. Reversible microgrooves have a higher oil mass flow rate, whereas HST micro-grooves have good performance, but they are difficult to produce. Spiral microgrooves have both an acceptable leakages and a high stiffness of liquid layer that is important in terms of ensuring of sealing performance at vibration conditions. Therefore, the spiral grooves were chosen for the developed seal. Based on calculation results, geometric dimensions were chosen to ensure the reliability of the seal operation by creating a guaranteed liquid film, which eliminates the wear of the sealing surfaces. Seals designed were tested both at the test rig and in the engine.

  19. Laser ignition - Spark plug development and application in reciprocating engines

    Science.gov (United States)

    Pavel, Nicolaie; Bärwinkel, Mark; Heinz, Peter; Brüggemann, Dieter; Dearden, Geoff; Croitoru, Gabriela; Grigore, Oana Valeria

    2018-03-01

    Combustion is one of the most dominant energy conversion processes used in all areas of human life, but global concerns over exhaust gas pollution and greenhouse gas emission have stimulated further development of the process. Lean combustion and exhaust gas recirculation are approaches to improve the efficiency and to reduce pollutant emissions; however, such measures impede reliable ignition when applied to conventional ignition systems. Therefore, alternative ignition systems are a focus of scientific research. Amongst others, laser induced ignition seems an attractive method to improve the combustion process. In comparison with conventional ignition by electric spark plugs, laser ignition offers a number of potential benefits. Those most often discussed are: no quenching of the combustion flame kernel; the ability to deliver (laser) energy to any location of interest in the combustion chamber; the possibility of delivering the beam simultaneously to different positions, and the temporal control of ignition. If these advantages can be exploited in practice, the engine efficiency may be improved and reliable operation at lean air-fuel mixtures can be achieved, making feasible savings in fuel consumption and reduction in emission of exhaust gasses. Therefore, laser ignition can enable important new approaches to address global concerns about the environmental impact of continued use of reciprocating engines in vehicles and power plants, with the aim of diminishing pollutant levels in the atmosphere. The technology can also support increased use of electrification in powered transport, through its application to ignition of hybrid (electric-gas) engines, and the efficient combustion of advanced fuels. In this work, we review the progress made over the last years in laser ignition research, in particular that aimed towards realizing laser sources (or laser spark plugs) with dimensions and properties suitable for operating directly on an engine. The main envisaged

  20. F3 turbofan engine. Overview of research and development

    Energy Technology Data Exchange (ETDEWEB)

    Kozu, Masao

    1986-12-10

    The development of XF3-30 Turbofan Engine (static propulsion 1670 kgf), to be equipped in the next exercise plane (XT-4) of the Air Self-Defense Force, was launched in FY 1975 and completed in FY 1985 in terms of certificate testing. This engine is the second national product after the first J3 in Japan. During the development work, technical gaps are avoided as far as possible while also noting cost control in mass production. Important items, felt during the development work for smoothly proceeding with the plan and early achieving the target, include optimum decision of low-fuel consumption rate, complete testing, careful study on the interface, long-term test run for detecting problems, frank attitude to accept facts, incentive of persons in charge and cooperation of related people. This report describes an outline of the plan from research to development, except for technical details that will be reported separately. (20 refs, 4 figs, 6 tabs, 5 photos)

  1. Development of Nuclear ship Engineering Simulation SYstem (NESSY)

    International Nuclear Information System (INIS)

    Kusunoki, Tsuyoshi; Kyouya, Masahiko; Takahashi, Teruo; Kobayashi, Hideo; Ochiai, Masa-aki; Hashidate, Kouji.

    1993-11-01

    NESSY has been developed for design studies of advanced marine reactors as a part of nuclear ship research and development since 1987. Engineering simulation model of the Mutsu, which is the first nuclear ship in Japan, was completed in March of 1993. In this report we concentration on detail description of softwares for Mutsu modeling. The aims of development of NESSY are as follows; (1) Assessment and confirmation on plant performance of an advanced marine reactor in each step of nuclear ship design (2) Development of abnormality diagnosis system and operator support system as a part of enhanced automization study, and study of human interface with hardware The characteristics of NESSY are the followings. (1) Total engineering simulation system simulate simultaneously ship motions, propulsion system behavior, and nuclear plant behavior under given weather and sea conditions. (2) Models based on physical theory as far as possible. (3) The simulator has high extensibility and flexibility. It is able to apply to other reactors, as the simulation model consists of the part of basic model and the part of plant data which are easy to change. After completion of Mutsu modeling, we are planning to utilize this system as one of design tools for an advanced marine reactor. (author)

  2. Developing English Communication Expertise for Engineers in the Global Age

    Science.gov (United States)

    Ono, Yoshimasa A.; Morimura, Kumiko

    This paper discusses contents and results of a new graduate course “English for Engineers and Scientists” given at School of Engineering, The University of Tokyo. This course is a new attempt to develop English communication expertise for engineering graduate students: how to write technical papers and how to make technical presentations in English. For these purposes, differences in the writing styles and in the sentence structures of English and Japanese are stressed: conclusions come first in English versus conclusions come last in Japanese; the three-step style of introduction, body, and conclusion in English versus the four-step style of ki-sho-ten-ketsu in Japanese. In addition, proper styles of technical papers (rhetoric) and related grammatical points are discussed. Technical presentation course consists of four-week lecture and seven-week practice session. In the lecture, essential points of technical presentations in English are discussed in detail, and in the practice session students‧ presentation skills are improved through guidance and instructions given by native-speaker moderators. The class evaluation results show that most students have obtained necessary skills of technical presentation, indicating that the combined course of lecture and practice session is essential for training students to make better technical presentations in English.

  3. Developing an Integration Infrastructure for Distributed Engine Control Technologies

    Science.gov (United States)

    Culley, Dennis; Zinnecker, Alicia; Aretskin-Hariton, Eliot; Kratz, Jonathan

    2014-01-01

    Turbine engine control technology is poised to make the first revolutionary leap forward since the advent of full authority digital engine control in the mid-1980s. This change aims squarely at overcoming the physical constraints that have historically limited control system hardware on aero-engines to a federated architecture. Distributed control architecture allows complex analog interfaces existing between system elements and the control unit to be replaced by standardized digital interfaces. Embedded processing, enabled by high temperature electronics, provides for digitization of signals at the source and network communications resulting in a modular system at the hardware level. While this scheme simplifies the physical integration of the system, its complexity appears in other ways. In fact, integration now becomes a shared responsibility among suppliers and system integrators. While these are the most obvious changes, there are additional concerns about performance, reliability, and failure modes due to distributed architecture that warrant detailed study. This paper describes the development of a new facility intended to address the many challenges of the underlying technologies of distributed control. The facility is capable of performing both simulation and hardware studies ranging from component to system level complexity. Its modular and hierarchical structure allows the user to focus their interaction on specific areas of interest.

  4. Development of engineering diffractometer at J-PARC

    Energy Technology Data Exchange (ETDEWEB)

    Moriai, Atsushi [Quantum Beam Science Directorate, Japan Atomic Energy Agency, Tokai-mura, Naka-gun, Ibaraki, 319-1195 (Japan)]. E-mail: atsushi.moriai@jaea.go.jp; Torii, Shuki [Quantum Beam Science Directorate, Japan Atomic Energy Agency, Tokai-mura, Naka-gun, Ibaraki, 319-1195 (Japan); Suzuki, Hiroshi [Quantum Beam Science Directorate, Japan Atomic Energy Agency, Tokai-mura, Naka-gun, Ibaraki, 319-1195 (Japan); Harjo, Stefanus [Quantum Beam Science Directorate, Japan Atomic Energy Agency, Tokai-mura, Naka-gun, Ibaraki, 319-1195 (Japan); Morii, Yukio [Quantum Beam Science Directorate, Japan Atomic Energy Agency, Tokai-mura, Naka-gun, Ibaraki, 319-1195 (Japan); Arai, Masatoshi [Quantum Beam Science Directorate, Japan Atomic Energy Agency, Tokai-mura, Naka-gun, Ibaraki, 319-1195 (Japan); Tomota, Yo [Ibaraki University, Hitachi-shi, Ibaraki, 316-8511 (Japan); Suzuki, Tetsuya [Ibaraki University, Hitachi-shi, Ibaraki, 316-8511 (Japan); Akiniwa, Yoshiaki [Nagoya University, Nagoya-shi, Aichi, 464-8603 (Japan); Kimura, Hidehiko [Nagoya University, Nagoya-shi, Aichi, 464-8603 (Japan); Akita, Koich [Musashi Institute of Technology, Setagaya-ku, Tokyo, 158-8557 (Japan)

    2006-11-15

    An engineering diffractometer for investigations of stresses and crystallographic structures within engineering components is now being developed at J-PARC project. The diffractometer is designed to view a decoupled-poisoned liquid H{sub 2} moderator providing neutrons with good symmetrical diffraction profiles in the acceptable wavelength range. The diffractometer will have a primary flight path of 40 m and a secondary flight path of 2.0 m for 90{sup o} scattering detector banks, and will include a curved supermirror neutron guide to avoid intensity loss due to the long flight path and to reduce backgrounds from fast neutrons and gamma rays. Therefore, stresses with sufficient accuracies in many engineering studies are quite promising. The diffractometer involves a sample translator which is able to handle large and heavy real industrial-scaled components. Detailed design works are being continuously promoted. The optimization of the diffractometer has been performed with a Monte Carlo simulation, and an appropriate resolution of less than 0.2% in {delta}d/d has been confirmed.

  5. Development of engineering diffractometer at J-PARC

    International Nuclear Information System (INIS)

    Moriai, Atsushi; Torii, Shuki; Suzuki, Hiroshi; Harjo, Stefanus; Morii, Yukio; Arai, Masatoshi; Tomota, Yo; Suzuki, Tetsuya; Akiniwa, Yoshiaki; Kimura, Hidehiko; Akita, Koich

    2006-01-01

    An engineering diffractometer for investigations of stresses and crystallographic structures within engineering components is now being developed at J-PARC project. The diffractometer is designed to view a decoupled-poisoned liquid H 2 moderator providing neutrons with good symmetrical diffraction profiles in the acceptable wavelength range. The diffractometer will have a primary flight path of 40 m and a secondary flight path of 2.0 m for 90 o scattering detector banks, and will include a curved supermirror neutron guide to avoid intensity loss due to the long flight path and to reduce backgrounds from fast neutrons and gamma rays. Therefore, stresses with sufficient accuracies in many engineering studies are quite promising. The diffractometer involves a sample translator which is able to handle large and heavy real industrial-scaled components. Detailed design works are being continuously promoted. The optimization of the diffractometer has been performed with a Monte Carlo simulation, and an appropriate resolution of less than 0.2% in Δd/d has been confirmed

  6. Center Planning and Development Student Engineer at KSC

    Science.gov (United States)

    Jenkins, Kenneth T., Jr.

    2015-01-01

    This summer I was the Student Trainee (Engineering) Pathways Intern (co-op) at the Kennedy Space Center (KSC) in the Center Planning & Development (CPD) Directorate. CPD works with commercial companies who are interested in using KSC's unique capabilities for spaceflight, spacecraft processing, ground systems and Research & Development (R&D) projects that fall in line with NASA's Mission and Vision. CPD is divided into three (3) groups: (1) AD-A, which works on the Master Planning for the center, (2) AD-B (where I am), which works on project control, management and integration, and (3) AD-C, which works on partnership development. CPD's main goal is to make KSC the world's preeminent multi-user spaceport and maintain the center as a leader in space exploration. CPD is a very diverse group of employees having a wide knowledge of not only the Space Shuttle, but also Expendable Launch Vehicles (ELV). The director of CPD, Scott Colloredo, is on the advisory board for Commercial Space Operations (CSO) and has a degree from ERAU. I worked on a number of different tasks for AD-B, as well as CPD, that includes, but not limited to: reviewing and reissuing engineering documents, weekly notes for CPD and senior management, engineering familiarizations with facilities at KSC, leading a tour for the Embry-Riddle Aeronautical University Career Services office, and working on actual agreements/proposals that will be used in the partnership process with multiple partners, along with other projects. Most of the work I have done is sensitive information and cannot be disclosed.

  7. Development Testing of 1-Newton ADN-Based Rocket Engines

    Science.gov (United States)

    Anflo, K.; Gronland, T.-A.; Bergman, G.; Nedar, R.; Thormählen, P.

    2004-10-01

    With the objective to reduce operational hazards and improve specific and density impulse as compared with hydrazine, the Research and Development (R&D) of a new monopropellant for space applications based on AmmoniumDiNitramide (ADN), was first proposed in 1997. This pioneering work has been described in previous papers1,2,3,4 . From the discussion above, it is clear that cost savings as well as risk reduction are the main drivers to develop a new generation of reduced hazard propellants. However, this alone is not enough to convince a spacecraft builder to choose a new technology. Cost, risk and schedule reduction are good incentives, but a spacecraft supplier will ask for evidence that this new propulsion system meets a number of requirements within the following areas: This paper describes the ongoing effort to develop a storable liquid monopropellant blend, based on AND, and its specific rocket engines. After building and testing more than 20 experimental rocket engines, the first Engineering Model (EM-1) has now accumulated more than 1 hour of firing-time. The results from test firings have validated the design. Specific impulse, combustion stability, blow-down capability and short pulse capability are amongst the requirements that have been demonstrated. The LMP-103x propellant candidate has been stored for more than 1 year and initial material compatibility screening and testing has started. 1. Performance &life 2. Impact on spacecraft design &operation 3. Flight heritage Hereafter, the essential requirements for some of these areas are outlined. These issues are discussed in detail in a previous paper1 . The use of "Commercial Of The Shelf" (COTS) propulsion system components as much as possible is essential to minimize the overall cost, risk and schedule. This leads to the conclusion that the Technology Readiness Level (TRL) 5 has been reached for the thruster and propellant. Furthermore, that the concept of ADN-based propulsion is feasible.

  8. Genetically engineered plants in the product development pipeline in India.

    Science.gov (United States)

    Warrier, Ranjini; Pande, Hem

    2016-01-02

    In order to proactively identify emerging issues that may impact the risk assessment and risk management functions of the Indian biosafety regulatory system, the Ministry of Environment, Forests and Climate Change sought to understand the nature and diversity of genetically engineered crops that may move to product commercialization within the next 10 y. This paper describes the findings from a questionnaire designed to solicit information about public and private sector research and development (R&D) activities in plant biotechnology. It is the first comprehensive overview of the R&D pipeline for GE crops in India.

  9. Engineering Education Development to Enhance Human Skill in DENSO

    Science.gov (United States)

    Isogai, Emiko; Nuka, Takeji

    Importance of human skills such as communication or instruction capability to their staff members has recently been highlighted in a workplace, due to decreasing opportunity of face-to-face communication between supervisors and their staff, or Instruction capability through OJT (On the Job Training) . Currently, communication skills are being reinforced mainly through OJT at DENSO. Therefore, as part of supplemental support tools, DENSO has established comprehensive engineers training program on off-JT basis for developing human skills, covering from newly employeed enginners up to managerial class since 2003. This paper describes education activities and reports the results.

  10. Development and engineering plan for graphite spent fuels conditioning program

    International Nuclear Information System (INIS)

    Bendixsen, C.L.; Fillmore, D.L.; Kirkham, R.J.; Lord, D.L.; Phillips, M.B.; Pinto, A.P.; Staiger, M.D.

    1993-09-01

    Irradiated (or spent) graphite fuel stored at the Idaho Chemical Processing Plant (ICPP) includes Fort St. Vrain (FSV) reactor and Peach Bottom reactor spent fuels. Conditioning and disposal of spent graphite fuels presently includes three broad alternatives: (1) direct disposal with minimum fuel packaging or conditioning, (2) mechanical disassembly of spent fuel into high-level waste and low-level waste portions to minimize geologic repository requirements, and (3) waste-volume reduction via burning of bulk graphite and other spent fuel chemical processing of the spent fuel. A multi-year program for the engineering development and demonstration of conditioning processes is described. Program costs, schedules, and facility requirements are estimated

  11. Development of biosensors and their application in metabolic engineering

    DEFF Research Database (Denmark)

    Zhang, Jie; Jensen, Michael Krogh; Keasling, Jay

    2015-01-01

    and ease of implementation with high-throughput analysis. Here we describe recent progress in biosensor development and their applications in a metabolic engineering context. We also highlight examples of how biosensors can be integrated with synthetic circuits to exert feedback regulation...... for the desired phenotypes. However, methods available for microbial genome diversification far exceed our ability to screen and select for those variants with optimal performance. Genetically encoded biosensors have shown the potential to address this gap, given their ability to respond to small molecule binding...

  12. Development of engineering scale HLLW vitrification technique at PNC

    International Nuclear Information System (INIS)

    Nagaki, H.; Oguino, N.; Tsunoda, N.; Segawa, T.

    1979-01-01

    Some processes have been investigated to develop the technology of solidification of the high-level radioactive liquid waste generated from the nuclear fuel reprocessing plant operated by the Power Reactor and Nuclear Fuel Development Corporation (PNC) at Tokai-mura. This report covers the present state of development of a Joule-heated ceramic melter and a direct megahertz induction-heated melter. Engineering-scale tests have been performed with both melters. The Joule-heated melter could produce 45 kg or 16 liters of glass per hour. The direct-induction furnace was able to melt 5 kg or 1.8 liters of glass per hour. Both melters were composed of electrofused cast refractory brick. Thus it was possible to melt the glass at above 1200 0 C. Glass produced at higher melting temperatures is generally superior. 3 figures, 2 tables

  13. Human factors in remote control engineering development activities

    International Nuclear Information System (INIS)

    Clarke, M.M.; Hamel, W.R.; Draper, J.V.

    1983-01-01

    Human factors engineering, which is an integral part of the advanced remote control development activities at the Oak Ridge National Laboratory, is described. First, work at the Remote Systems Development Facility (RSDF) has shown that operators can perform a wide variety of tasks, some of which were not specifically designed for remote systems, with a dextrous electronic force-reflecting servomanipulator and good television remote viewing capabilities. Second, the data collected during mock-up remote maintenance experiments at the RSDF have been analyzed to provide guidelines for the design of human interfaces with an integrated advanced remote maintenance system currently under development. Guidelines have been provided for task allocation between operators, remote viewing systems, and operator controls. 6 references, 5 figures, 2 tables

  14. Sublimator Driven Coldplate Engineering Development Unit Test Results

    Science.gov (United States)

    Sheth, Rubik B.; Stephan, Ryan A.; Leimkuehler, Thomas O.

    2010-01-01

    The Sublimator Driven Coldplate (SDC) is a unique piece of thermal control hardware that has several advantages over a traditional thermal control scheme. The principal advantage is the possible elimination of a pumped fluid loop, potentially increasing reliability and reducing complexity while saving both mass and power. Because the SDC requires a consumable feedwater, it can only be used for short mission durations. Additionally, the SDC is ideal for a vehicle with small transport distances and low heat rejection requirements. An SDC Engineering Development Unit was designed and fabricated. Performance tests were performed in a vacuum chamber to quantify and assess the performance of the SDC. The test data was then used to develop correlated thermal math models. Nonetheless, an Integrated Sublimator Driven Coldplate (ISDC) concept is being developed. The ISDC couples a coolant loop with the previously described SDC hardware. This combination allows the SDC to be used as a traditional coldplate during long mission phases and provides for dissimilar system redundancy

  15. TRENDS IN PRODUCT DEVELOPMENT: CONCURRENT ENGINEERING AND MECHATRONICS

    Directory of Open Access Journals (Sweden)

    Stefan IANCU

    2013-05-01

    Full Text Available This paper presents the most significant contemporary trends in new industrial product development:concurrent engineering (CE and mechatronics (M. Author defines what CE and M are, emphasizing whatconnections are between these two concepts, and which are the ways of integration in CE and M. The mainconclusion of this paper is that both these two concepts have known a strongly development in 1975-1985’s,when Information and Communication Technologies (ICT was in full swing of development. The influence ofICT is undoubted, but, from this point of view, there are differences: if M could not be implemented in theabsence of the ICT, communication and computational technologies are not strictly necessary for theimplementation of CE.

  16. Necessity of nuclear power engineering development in Kazakstan

    International Nuclear Information System (INIS)

    Takibaev, Zh.S.; Cherepnin, Yu.S.

    1996-01-01

    Kazakstan is a great land country. Mining and delivery of great coal amount to power facilities will require to rise prices for electrical power. High expenditures for energy will lead to rising prime cost of every industry production unit produced in the country. If all power supply in the country is obtained from solid fuel, than geographical factor would be a heavy weight for it economy that would be not able to produce competition able. There is no doubt, that Kazakstan coal power supply will be prevailing electric power source for a long period of future. But it is urgently necessary consider and develop alternative conceptions for development of young country. There are a number of favourable reasons for atomic power engineering development

  17. Developing engineering design core competences through analysis of industrial products

    DEFF Research Database (Denmark)

    Hansen, Claus Thorp; Lenau, Torben Anker

    2011-01-01

    Most product development work carried out in industrial practice is characterised by being incremental, i.e. the industrial company has had a product in production and on the market for some time, and now time has come to design a new and upgraded variant. This type of redesign project requires...... that the engineering designers have core design competences to carry through an analysis of the existing product encompassing both a user-oriented side and a technical side, as well as to synthesise solution proposals for the new and upgraded product. The authors of this paper see an educational challenge in staging...... a course module, in which students develop knowledge, understanding and skills, which will prepare them for being able to participate in and contribute to redesign projects in industrial practice. In the course module Product Analysis and Redesign that has run for 8 years we have developed and refined...

  18. Development of Engineering Design Education in the Department of Mechanical Engineering at Kanazawa Technical College

    Science.gov (United States)

    Yamada, Hirofumi; Ten-Nichi, Michio; Mathui, Hirosi; Nakamura, Akizi

    This paper introduces a method of the engineering design education for college of technology mechanical engineering students. In order to teach the practical engineering design, the MIL-STD-499A process is adapted and improved upon for a Mechatronics hands-on lesson used as the MOT method. The educational results in five years indicate that knowledge of the engineering management is useful for college students in learning engineering design. Portfolio for lessons and the hypothesis method also have better effects on the understanding of the engineering specialty.

  19. Development of a Gas-Fed Pulse Detonation Research Engine

    Science.gov (United States)

    Litchford, Ron J.; Hutt, John (Technical Monitor)

    2001-01-01

    In response to the growing need for empirical data on pulse detonation engine performance and operation, NASA Marshall Space Flight Center has developed and placed into operation a low-cost gas-fed pulse detonation research engine. The guiding design strategy was to achieve a simple and flexible research apparatus, which was inexpensive to build and operate. As such, the engine was designed to operate as a heat sink device, and testing was limited to burst-mode operation with run durations of a few seconds. Wherever possible, maximum use was made of standard off-the-shelf industrial or automotive components. The 5-cm diameter primary tube is about 90-cm long and has been outfitted with a multitude of sensor and optical ports. The primary tube is fed by a coaxial injector through an initiator tube, which is inserted directly into the injector head face. Four auxiliary coaxial injectors are also integrated into the injector head assembly. All propellant flow is controlled with industrial solenoid valves. An automotive electronic ignition system was adapted for use, and spark plugs are mounted in both tubes so that a variety of ignition schemes can be examined. A microprocessor-based fiber-optic engine control system was developed to provide precise control over valve and ignition timing. Initial shakedown testing with hydrogen/oxygen mixtures verified the need for Schelkin spirals in both the initiator and primary tubes to ensure rapid development of the detonation wave. Measured pressure wave time-of-flight indicated detonation velocities of 2.4 km/sec and 2.2 km/sec in the initiator and primary tubes, respectively. These values implied a fuel-lean mixture corresponding to an H2 volume fraction near 0.5. The axial distribution for the detonation velocity was found to be essentially constant along the primary tube. Time-resolved thrust profiles were also acquired for both underfilled and overfilled tube conditions. These profiles are consistent with previous time

  20. Hydraulic modeling development and application in water resources engineering

    Science.gov (United States)

    Simoes, Francisco J.; Yang, Chih Ted; Wang, Lawrence K.

    2015-01-01

    The use of modeling has become widespread in water resources engineering and science to study rivers, lakes, estuaries, and coastal regions. For example, computer models are commonly used to forecast anthropogenic effects on the environment, and to help provide advanced mitigation measures against catastrophic events such as natural and dam-break floods. Linking hydraulic models to vegetation and habitat models has expanded their use in multidisciplinary applications to the riparian corridor. Implementation of these models in software packages on personal desktop computers has made them accessible to the general engineering community, and their use has been popularized by the need of minimal training due to intuitive graphical user interface front ends. Models are, however, complex and nontrivial, to the extent that even common terminology is sometimes ambiguous and often applied incorrectly. In fact, many efforts are currently under way in order to standardize terminology and offer guidelines for good practice, but none has yet reached unanimous acceptance. This chapter provides a view of the elements involved in modeling surface flows for the application in environmental water resources engineering. It presents the concepts and steps necessary for rational model development and use by starting with the exploration of the ideas involved in defining a model. Tangible form of those ideas is provided by the development of a mathematical and corresponding numerical hydraulic model, which is given with a substantial amount of detail. The issues of model deployment in a practical and productive work environment are also addressed. The chapter ends by presenting a few model applications highlighting the need for good quality control in model validation.

  1. 76 FR 10403 - Hewlett Packard (HP), Global Product Development, Engineering Workstation Refresh Team, Working...

    Science.gov (United States)

    2011-02-24

    ...), Global Product Development, Engineering Workstation Refresh Team, Working On-Site at General Motors..., Non-Information Technology Business Development Team and Engineering Application Support Team, working... Hewlett Packard, Global Product Development, Engineering Workstation Refresh Team, working on-site at...

  2. 75 FR 48411 - Research, Engineering and Development Advisory Committee; Notice of Meeting

    Science.gov (United States)

    2010-08-10

    ... DEPARTMENT OF TRANSPORTATION Federal Aviation Administration Research, Engineering and Development.... 2), notice is hereby given of a meeting of the FAA Research, Engineering and Development (R, E&D) Advisory Committee. Name: Research, Engineering & Development Advisory Committee. Time and Date: September...

  3. Development of security engineering curricula at US universities

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, M.L.

    1998-06-01

    The Southwest Surety Institute was formed in 1996 to create unique, science-based educational programs in security engineering. The programs will integrate business, technology, and criminal justice elements to educate a new generation of security professionals. Graduates of the programs will better understand basic security system design and evaluation and contribute to strengthening of the body of knowledge in the area of security. A systematic approach incorporating people, procedures, and equipment will be taught that will emphasize basic security principles and establish the science of security engineering. The use of performance measures in the analysis of designed systems will enable effective decisions by an enterprise and provide the rationale for investment in security systems. Along with educational programs, Institute members will conduct original research and development built on existing relationships with sponsors from government and industry in areas such as counterterroism, microelectronics, banking, aviation, and sensor development. Additional information and updates on the Southwest Surety Institute are available via the Institute home page at www.emrtc.nmt.edu/ssi.

  4. Developing Smartphone Apps for Education, Outreach, Science, and Engineering

    Science.gov (United States)

    Weatherwax, A. T.; Fitzsimmons, Z.; Czajkowski, J.; Breimer, E.; Hellman, S. B.; Hunter, S.; Dematteo, J.; Savery, T.; Melsert, K.; Sneeringer, J.

    2010-12-01

    The increased popularity of mobile phone apps provide scientists with a new avenue for sharing and distributing data and knowledge with colleagues, while also providing meaningful education and outreach products for consumption by the general public. Our initial development of iPhone and Android apps centered on the distribution of exciting auroral images taken at the South Pole for education and outreach purposes. These portable platforms, with limited resources when compared to computers, presented a unique set of design and implementation challenges that we will discuss in this presentation. For example, the design must account for limited memory; screen size; processing power; battery life; and potentially high data transport costs. Some of these unique requirements created an environment that enabled undergraduate and high-school students to participate in the creation of these apps. Additionally, during development it became apparent that these apps could also serve as data analysis and engineering tools. Our presentation will further discuss our plans to use apps not only for Education and Public Outreach, but for teaching, science and engineering.

  5. Advanced tendencies in development of photovoltaic cells for power engineering

    Science.gov (United States)

    Strebkov, D. S.

    2015-01-01

    Development of solar power engineering must be based on original innovative Russian and world technologies. It is necessary to develop promising Russian technologies of manufacturing of photovoltaic cells and semiconductor materials: chlorine-free technology for obtaining solar silicon; matrix solar cell technology with an efficiency of 25-30% upon the conversion of concentrated solar, thermal, and laser radiation; encapsulation technology for high-voltage silicon solar modules with a voltage up to 1000 V and a service life up to 50 years; new methods of concentration of solar radiation with the balancing illumination of photovoltaic cells at 50-100-fold concentration; and solar power systems with round-the-clock production of electrical energy that do not require energy storage devices and reserve sources of energy. The advanced tendency in silicon power engineering is the use of high-temperature reactions in heterogeneous modular silicate solutions for long-term (over one year) production of heat and electricity in the autonomous mode.

  6. Systems engineering identification and control of mixed waste technology development

    International Nuclear Information System (INIS)

    Beitel, G.A.

    1997-01-01

    The Department of Energy (DOE) established the Mixed Waste Characterization, Treatment, and Disposal Focus Area (MWFA) to develop technologies required to meet the Department's commitments for treatment of mixed low-level and transuranic wastes. Waste treatment includes all necessary steps from generation through disposal. Systems engineering was employed to reduce programmatic risk, that is, risk of failure to meet technical commitments within cost and schedule. Customer needs (technology deficiencies) are identified from Site Treatment Plans, Consent Orders, ten year plans, Site Technical Coordinating Groups, Stakeholders, and Site Visits. The Technical Baseline, a prioritized list of technology deficiencies, forms the basis for determining which technology development activities will be supported by the MWFA. Technology Development Requirements Documents are prepared for each technology selected for development. After technologies have been successfully developed and demonstrated, they are documented in a Technology Performance Report. The Technology Performance Reports are available to any of the customers or potential users of the technology, thus closing the loop between problem identification and product development. This systematic approach to technology development and its effectiveness after 3 years is discussed in this paper

  7. Complex approach in telecommunication engineering education: develop engineering skills by a team project

    Directory of Open Access Journals (Sweden)

    Scripcariu Luminița

    2017-01-01

    Full Text Available This paper provides an overview of the educational process of telecommunication engineering students by presenting the preparation of a team project focused on information security. Our educational approach combines basic knowledge such as mathematics with specialized engineering notions and various skills. The project theme is to design, implement and test an encryption algorithm. Students are provided with online courses, specific software programs and Internet access. They have to choose an encryption algorithm, to study its details and to write the script of the encryption algorithm in MATLAB program. The algorithm is implemented in C/C++ programming language and tested. Finally, a concurrent team tries to break the algorithm by finding the decryption key. It is an interactive approach which combines various education methods including gaming concepts. The covered topics provide students professional outcomes such as knowledge and use of specific mathematical tools and software environments (C/C ++ programming languages, MATLAB, abilities to design, develop, implement and test software algorithms. The project also provides transversal outcomes such as ability to team work, skills of computer use and information technology and capability to take responsibilities. Creativity is also encouraged by extending the algorithm to other encryption key lengths than the usual ones.

  8. An Integrated Surface Engineering Technology Development for Improving Energy Efficiency of Engine Components

    Energy Technology Data Exchange (ETDEWEB)

    Stephen Hsu; Liming Chang; Huan Zhan

    2009-05-31

    Frictional losses are inherent in most practical mechanical systems. The ability to control friction offers many opportunities to achieve energy conservation. Over the years, materials, lubricants, and surface modifications have been used to reduce friction in automotive and diesel engines. However, in recent years, progress in friction reduction technology has slowed because many of the inefficiencies have been eliminated. A new avenue for friction reduction is needed. Designing surfaces specifically for friction reduction with concomitant enhanced durability for various engine components has emerged recently as a viable opportunity due to advances in fabrication and surface finishing techniques. Recently, laser ablated dimples on surfaces have shown friction reduction properties and have been demonstrated successfully in conformal contacts such as seals where the speed is high and the load is low. The friction reduction mechanism in this regime appears to depend on the size, patterns, and density of dimples in the contact. This report describes modeling efforts in characterizing surface textures and understanding their mechanisms for enhanced lubrication under high contact pressure conditions. A literature survey is first presented on the development of descriptors for irregular surface features. This is followed by a study of the hydrodynamic effects of individual micro-wedge dimples using the analytical solution of the 1-D Reynolds equation and the determination of individual components of the total friction resistance. The results obtained provide a better understanding of the dimple orientation effects and the approach which may be used to further compare the friction reduction provided by different texture patterns.

  9. Update of development on the new Audi NSU rotary engine generation. [for application to aircraft engines

    Science.gov (United States)

    Vanbasshuysen, R.

    1978-01-01

    Rotary engines with a chamber volume of 750 cc as a two rotor automotive powerplant, called KKM 871 are described. This engine is compared to a 3 liter or 183 cubic inch, six-cylinder reciprocating engine. Emphasis is placed on exhaust emission control and fuel economy.

  10. TECHNOLOGICAL CONTRIBUTIONS OF THE MILITARY ENGINEERING TO THE NATIONAL DEVELOPMENT

    Directory of Open Access Journals (Sweden)

    RODRIGO CARO DE KARTZOW

    2018-01-01

    Full Text Available The development of the Chilean military industry is closely related to the growing of the national industry. Similarly to the way the history of the Army and the country are tightly related, the history of the military engineering is an example of organic growth when compared to its civilian counterpart. Collaboration instead of competition is the distinctive seal that best shows the development of weaponry, explosives, cartography and nuclear power. This collaboration have lasted with the years and we can afirm today that the relationship within civilian professionals and technicians and their military counterparts has reached an state that has never seen before. The governmental policies that fund R&D of initiatives that facilitate the science and technology study and research, come of a futuristic vision, born in the rim of the independent movements, driven naturally by the need of self sustain as sovereign nations.

  11. Engineering development studies for integrated evacuated CPC arrays

    Science.gov (United States)

    Winston, R.

    1982-04-01

    An evacuated tube concentrator which achieves respectable high temperature performance (100 C to 300 C) was developed. The design concept utilizes nonimaging CPC type concentration integrated into each tube by shaping the outer glass vacuum envelope. The detailed design, prototype fabrication and preliminary test measurements are reviewed. In addition the results of this first study specifically devoted to engineering development questions related to practical applications of this collector concept are summarized. Questions having to do with the deployment of medium to large area arrays, optimizations of the manifolding of individual tube panels, selected near term applications (with an emphasis on residential cooling based on Rankine driven chillers) and long term performance projections are addressed.

  12. Developing an interactive intervention planner: a systems engineering perspective

    CERN Document Server

    Fabry, Thomas; Feral, Bruno; Braesch, Christian

    2013-01-01

    Intervention planning is crucial for maintenance operations in particle accelerator environments with ionizing radiation, during which the radiation dose received by maintenance workers should be reduced to a minimum. In this context, we discuss the development of a new software tool and the entailed methodology, including the visualization aspects. The software tool integrates interactive exploration of a scene depicting an accelerator facility augmented with residual radiation level simulations, with the visualization of intervention data such as the followed trajectory and maintenance tasks. Its conception allows for future inclusion of measurements performed by mobile robotic devices. In this work, we explore the systems engineering life cycle of the development process of an interactive intervention planner, which includes the needs analysis, specification explicitation, conceptual mathematical modelling, iterative implementation, design and prototype testing and usability testing.

  13. Developing an Interactive Intervention Planner - A Systems Engineering Perspective

    Directory of Open Access Journals (Sweden)

    Thomas Fabry

    2013-09-01

    Full Text Available Intervention planning is crucial for maintenance operations in particle accelerator environments with ionizing radiation, during which the radiation dose received by maintenance workers should be reduced to a minimum. In this context, we discuss the development of a new software tool and the entailed methodology, including the visualization aspects. The software tool integrates interactive exploration of a scene depicting an accelerator facility augmented with residual radiation level simulations, with the visualization of intervention data such as the followed trajectory and maintenance tasks. Its conception allows for future inclusion of measurements performed by mobile robotic devices. In this work, we explore the systems engineering life cycle of the development process of an interactive intervention planner, which includes the needs analysis, specification explicitation, conceptual mathematical modelling, iterative implementation, design and prototype testing and usability testing.

  14. Nuclear Plant Analyzer development at the Idaho National Engineering Laboratory

    International Nuclear Information System (INIS)

    Laats, E.T.; Beelman, R.J.; Charlton, T.R.; Hampton, N.L.; Burtt, J.D.

    1985-01-01

    The Nuclear Plant Analyzer (NPA) is a state-of-the-art safety analysis and engineering tool being used to address key nuclear power plant safety issues. The NPA has been developed to integrate the NRC's computerized reactor behavior simulation codes such as RELAP5, TRAC-BWR, and TRAC-PWR, with well-developed computer graphics programs and large repositories of reactor design and experimental data. An important feature of the NAP is the capability to allow an analyst to redirect a RELAP5 or TRAC calculation as it progresses through its simulated scenario. The analyst can have the same power plant control capabilities as the operator of an actual plant. The NPA resides on the dual CDS Cyber-176 mainframe computers at the INEL and is being converted to operate on a Cray-1S computer at the LANL. The subject of this paper is the program conducted at the INEL

  15. Intra- and interpopulation relationships and taxonomic status of Pinus nigra Arnold in Croatia according to morphology and anatomy of needles

    Directory of Open Access Journals (Sweden)

    Zlatko Liber

    2014-01-01

    Full Text Available Intra- and interpopulational relationships and taxonomic status of six natural black pine populations (Pinus nigra Arnold from Croatia were analyzed. Special attention in this research was paid to the establishment of taxonomic status and distribution of stenoendemic Dalmatian black pine (Pinus nigra Arnold subsp. dalmatica (Vis. Franco. Three morphological and twenty-one anatomical traits of needles were used as well as analysis by the methods of multivariate statistics. Most of the researched individuals showed strong population affiliation, whereas a clinal transition of morphological and anatomical traits of needles was determined among the populations. The opinion of the existence of three subspecies of black pine on the territory of Republic of Croatia (Pinus nigra Arnold subsp. nigra, Pinus nigra Arnold subsp. dalmatica (Vis. Franco and Pinus nigra Arnold subsp. illyrica (Vid. Fukarek was confirmed. For each of the three subspecies new ranges were represented. Four Croatian populations were included in the stenoendemic subspecies of the Dalmatian black pine (Brač, Hvar, Grobnik and Pelješac, and a new distribution, broken in two, was suggested. Since the Dalmatian black pine has been reduced to several populations only, and there are some signs of continuous diminishing of its range, this research points out the need of making an action plan to preserve all natural populations of this subspecies.

  16. Satisfying the diverse development needs of an engineering organization

    International Nuclear Information System (INIS)

    Zarkesh, L.P.

    1991-01-01

    The Engineering Department at Davis-Besse Nuclear Power Station has established an aggressive philosophy for professionally developing their staff. This philosophy has evolved over the last four years into a program with specialized administrative tools which not only satisfies the intent of industry training guidelines, but also accentuates the development of the individual. This program consists of three parts: (1) The Development Program - A program constructed to actively integrate system and applied science courses, management and interpersonal skill courses, design basis courses (e.g., pipe break analysis, support design, etc.) special process courses (e.g., human factors, ALARA, etc.) and external seminars sponsored by industry experts; (2) The Individual Development Plan (IDP) - A documented course of action, developed annually, in which the employee and the line supervisor jointly contribute to the identification of career goals and strategic professional objectives; and (3) The Training Database - A PC database developed to retain and manage course information (e.g., requests, attendance priorities, schedule, history, etc.). The paper describes these three facets of the training program

  17. Development of salt tolerant plants through genetic engineering (abstract)

    International Nuclear Information System (INIS)

    Mukhtar, Z.; Khan, S.A.; Zafar, Y.

    2005-01-01

    Salinity stress is one of the most serious factors limiting the productivity of agricultural crops. Genetic engineering provides a useful tool for tailoring plants with enhanced salt tolerance characteristics. Many organisms have evolved mechanisms to survive and grow under such extreme environments. These organisms provide us with a useful source of genes which can be used to improve salt tolerance in plants. The present study aims at identification and cloning of useful halo tolerance conferring genes from fungi and plants and to develop salt tolerant transgenic plants. Here we describe the cloning and use of HSR1 gene (a yeast transcription factor known to confer salt tolerance) and Na/sup +//H/sup +/ antiporter gene AtNHX1 (3016 bp) from Arabidopsis thaliana, and transformation of tobacco with HSR1 and AtNHX1 genes through Agrobacterium method. A number of transgenic tobacco plants were regenerated from leaf explants transformed with Agrobacterium tumefaciens (LBA4404) having HSR1 and AtNHX1 genes by leaf disc method. The putative transgenic plants were analyzed by PCR and dot blot analysis. Screening of these transgenic plants at different salinity levels is in progress which will help identify the suitable plant lines and thus the promising genes which can be further exploited to engineer salt tolerant crop plants. (author)

  18. Free-Piston Shock Tunnel Test Technique Development: An AEDC/DLR Cooperative Program

    Science.gov (United States)

    2003-02-01

    Felderman Jacobs Sverdrup AEDC Group W. H. Beck and K. Hannemann DLR February 2003 Final Report for Period Ocotober 1997 — September 2001 ARNOLD ENGINEERING...Group W. H. Beck and K. Hannemann , DLR AEDC-TR-01-5 SAF/IAQ Attn: Maj. Keller 1080 Air Force Pentagon Washington, DC 20330-1080 Arnold Engineering...Canberra, 1968. 8. Hannemann , K., et al. " The Influence and the Delay of Driver Gas Contamination in HEG." AIAA 21st Aerodynamic Measurement

  19. Engineering the development of optical fiber sensors for adverse environments

    International Nuclear Information System (INIS)

    Hastings, M.C.

    1994-01-01

    During the last decade, many optical fiber sensors have been developed for particular applications in harsh environments with limited success. Off-the-shelf optical fiber sensors and measurement systems are not available, partly because they have not been engineered to meet tough environmental requirements necessary for applications outside the laboratory. Moreover, no generalized computer-aided tools exist to help advance their development, design, and use. Computer-aided design tools currently being developed are described in this paper. Structural finite element analyses have been coupled with optoelastic analyses of both all-fiber interferometers and serial microbend sensors for distributed measurement of various physical quantities. The combined analyses have been parameterized and implemented on personal computers and work stations for use as design/development tools that can be used to determine the performance of different sensor configurations in various environments. Potentially, these computer-aided tools could be used for failure diagnosis and redesign of existing optical fiber sensors. Performances predicted by the computer simulations are verified with experimental data and numerical analyses from the literature. The long-term goal is to develop user-friendly software packages for both sensor manufacturers and end users

  20. Development Cooperation as Methodology for Teaching Social Responsibility to Engineers

    Science.gov (United States)

    Lappalainen, Pia

    2011-01-01

    The role of engineering in promoting global well-being has become accentuated, turning the engineering curriculum into a means of dividing well-being equally. The gradual fortifying calls for humanitarian engineering have resulted in the incorporation of social responsibility themes in the university curriculum. Cooperation, communication,…

  1. Liminality and Traces of Affectivity in the Work of Arnold van Gennep

    DEFF Research Database (Denmark)

    Thomassen, Bjørn

    2013-01-01

    Linking liminality with affectivity does not mean to propose new and alternative interpretations of what liminality is or could be, taking it to territories distant from its place of origin, quite the contrary: it means to move the concept back to its rightful place in intellectual history, back ...... to the centre of human emotions trembling at the threshold. This can best be indicated by tracing how affectivity was a theme in Arnold van Gennep’s (AvG) life-work, even if it was not a word he used....

  2. Presidendipaari avaldus / Rüütel Arnold, Ingrid Rüütel

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2006-01-01

    Ilmunud ka Postimees : na russkom jazõke (2006) 23. jaan., lk. 2 ; Eesti Päevaleht (2006) 23. jaan., lk. 6 ; SL Õhtuleht (2006) 23. jaan., lk. 2 ; Hiiu Leht (2006) 24. jaan., lk. 2 ; Harjumaa (2006) 24. jaan., lk. 1 ; Pärnu Postimees (2006) 24. jaan., lk. 19 ; Virumaa Teataja (2006) 24. jaan., lk. 7 ; Sakala (2006) 24. jaan., lk. 2 ; Võrumaa Teataja (2006) 24. jaan., lk. 2 ; Põhjarannik (2006) 24. jaan., lk. 2 ; Severnoje Poberezhje (2006) 24. jaan., lk. 2 ; Meie Maa (2006/) 24. jaan., lk. 2. President Arnold Rüütli ja proua Ingrid Rüütli avaldus seoses Kadrioru lossis toimunud noortepidudega

  3. Development trend of low bypass ratio turbofan engines. Tei baipasu hi tabo fan engine no kaihatsu doko

    Energy Technology Data Exchange (ETDEWEB)

    Yashima, S [Ishikawajima-Harima Heavy Industries Co. Ltd., Tokyo (Japan)

    1994-03-10

    As a turbojet engine gets a thrust by blowing out the exhaust of a gas generator, for decreasing the fuel consumption ratio is more advantageous when a bypass air quantity is made as much as possible. Therefore in the subsonic speed passenger aircrafts putting an economy in the first place, the high bypass ratio turbofan engines are used. Even in case of the subsonic speed aircrafts, in addition, for the trainer airplanes and fighters, a type to be built in the engines in the fuselages, the low bypass ratio engines with small front areas are used. When a turbofan engine with a low bypass ratio is picked up, therefore recently, it is general that a military engine with a bypass ratio under 1 (about 0.5 is frequent) is pointed, as for a development trend also from a viewpoint of the performance improvement as a military engine, an improvement of the thrust-weight ratio and specific thrust are attached importance to. In this paper, these performance parameters, a trend to make them lighter weight, and the elementary technologies peculiar to a low bypass ratio engine are described, and moreover the study and development state in Europe, America and Japan are put in order. 8 refs., 14 figs., 2 tabs.

  4. Alliance for Earth Sciences, Engineering and Development in Africa

    Science.gov (United States)

    Barron, E. J.; Adewumi, M.

    2004-12-01

    Penn State University, with a significant number of African University partners (University of Ibadan, University of Lagos, University of Cape Town, University of Witwatersrand, and Agustino Neto University) as well as HBCUs (Howard University and the Mississippi Consortium for International Development - a consortium of four HBCUs in Mississippi), has established the Alliance for Earth Sciences, Engineering and Development in Africa (AESEDA). AESEDA is designed to enable the integration of science, engineering, and social sciences in order to develop human resources, promote economic vitality and enable environmental stewardship in Africa. The Alliance has a coherent and significant multidisciplinary focus, namely African georesources. Education is a central focus, with research collaboration as one element of the vehicle for education. AESEDA is focused on building an environment of intellectual discourse and pooled intellectual capital and developing innovative and enabling educational programs and enhancing existing ones. AESEDA also has unique capabilities to create role models for under-represented groups to significantly enable the utilization of human potential. The efforts of the Alliance center around specific activities in support of its objectives: (1) Focused research collaboration among partner institutions, (2) Development of an international community of scholars, and (3) Joint development of courses and programs and instructional innovation. Penn State has a unique ability to contribute to the success of this program. The College of Earth and Mineral Sciences contains strong programs in the areas of focus. More than 25 faculty in the College have active research and educational efforts in Africa. Hence, the Alliance has natural and vigorous support within the College. The College is also providing strong institutional support for AESEDA, by establishing a Director and support staff and creating permanent funds for a unique set of new faculty hires

  5. In situ sampling cart development engineering task plan

    International Nuclear Information System (INIS)

    DeFord, D.K.

    1995-01-01

    This Engineering Task Plan (ETP) supports the development for facility use of the next generation in situ sampling system for characterization of tank vapors. In situ sampling refers to placing sample collection devices (primarily sorbent tubes) directly into the tank headspace, then drawing tank gases through the collection devices to obtain samples. The current in situ sampling system is functional but was not designed to provide the accurate flow measurement required by today's data quality objectives (DQOs) for vapor characterization. The new system will incorporate modern instrumentation to achieve much tighter control. The next generation system will be referred to in this ETP as the New In Situ System (NISS) or New System. The report describes the current sampling system and the modifications that are required for more accuracy

  6. Development of an engineering model for ferromagnetic shape memory alloys

    International Nuclear Information System (INIS)

    Tani, Yoshiaki; Todaka, Takashi; Enokizono, Masato

    2008-01-01

    This paper presents a relationship among stress, temperature and magnetic properties of a ferromagnetic shape memory alloy. In order to derive an engineering model of ferromagnetic shape memory alloys, we have developed a measuring system of the relationship among stress, temperature and magnetic properties. The samples used in this measurement are Fe68-Ni10-Cr9-Mn7-Si6 wt% ferromagnetic shape memory alloy. They are thin ribbons made by rapid cooling in air. In the measurement, the ribbon sample is inserted into a sample holder winding consisting of the B-coil and compensation coils, and magnetized in an open solenoid coil. The ribbon is stressed with attachment weights and heated with a heating wire. The specific susceptibility was increased by applying tension, and slightly increased by heating below the Curie temperature

  7. Reconstruction of Orion Engineering Development Unit (EDU) Parachute Inflation Loads

    Science.gov (United States)

    Ray, Eric S.

    2013-01-01

    The process of reconstructing inflation loads of Capsule Parachute Assembly System (CPAS) has been updated as the program transitioned to testing Engineering Development Unit (EDU) hardware. The equations used to reduce the test data have been re-derived based on the same physical assumptions made by simulations. Due to instrumentation challenges, individual parachute loads are determined from complementary accelerometer and load cell measurements. Cluster inflations are now simulated by modeling each parachute individually to better represent different inflation times and non-synchronous disreefing. The reconstruction procedure is tailored to either infinite mass or finite mass events based on measurable characteristics from the test data. Inflation parameters are determined from an automated optimization routine to reduce subjectivity. Infinite mass inflation parameters have been re-defined to avoid unrealistic interactions in Monte Carlo simulations. Sample cases demonstrate how best-fit inflation parameters are used to generate simulated drag areas and loads which favorably agree with test data.

  8. A review of Curtiss-Wright rotary engine developments with respect to general aviation potential

    Science.gov (United States)

    Jones, C.

    1979-01-01

    Aviation related rotary (Wankel-type) engine tests, possible growth directions and relevant developments at Curtiss-Wright have been reviewed. Automotive rotary engines including stratified charge are described and flight test results of rotary aircraft engines are presented. The current 300 HP engine prototype shows basic durability and competitive performance potential. Recent parallel developments have separately confirmed the geometric advantages of the rotary engine for direct injected unthrottled stratified charge. Specific fuel consumption equal to or better than pre- or swirl-chamber diesels, low emission and multi-fuel capability have been shown by rig tests of similar rotary engine.

  9. Advanced mechanics from Euler's determinism to Arnold's chaos

    CERN Document Server

    Rajeev, S G

    2013-01-01

    Classical Mechanics is the oldest and best understood part of physics. This does not mean that it is cast in marble yet, a museum piece to be admired from a distance. Instead, mechanics continues to be an active area of research by physicists and mathematicians. Every few years, we need to re-evaluate the purpose of learning mechanics and look at old material in the light of modern developments. Once you have learned basic mechanics (Newton's laws, the solution of the Kepler problem) and quantum mechanics (the Schrodinger equation, hydrogen atom) it is time to go back and relearn classical mechanics in greater depth. It is the intent of this book to take you through the ancient (the original meaning of "classical") parts of the subject quickly: the ideas started by Euler and ending roughly with Poincare. We then take up the developments of twentieth century physics that have largely to do with chaos and discrete time evolution (the basis of numerical solutions).

  10. Development of the Canadian used fuel repository engineered barrier system

    Energy Technology Data Exchange (ETDEWEB)

    Hatton, C., E-mail: chatton@nwmo.ca [Nuclear Waste Management Organization, Toronto, ON (Canada)

    2015-07-01

    The Nuclear Waste Management Organization (NWMO) is responsible for the implementation of Adaptive Phased Management (APM), the federally-approved plan for the safe long-term management of Canada's used nuclear fuel. Under the APM plan, used nuclear fuel will ultimately be placed within a deep geological repository in a suitable rock formation. In implementing APM, the NWMO is committed to ensure consistency with international best practices in the development of its repository system, including any advances in technology. In 2012, the NWMO undertook an optimization study to look at both the design and manufacture of its engineered barriers. This study looked at current technologies for the design and manufacture of used fuel containers, placement technologies, repository design, and buffer and sealing systems, while taking into consideration the state of the art worldwide in repository design and acceptance. The result of that study is the current Canadian engineered barrier system, consisting of a 2.7 tonne used fuel container with a carbon-steel core, copper-coated surface and welded spherical heads. The used fuel container is encapsulated in a bentonite buffer box at the surface and then transferred underground. Once underground, the used fuel is placed into a repository room which is cut into the rock using traditional drill-and-blast technologies. This paper explains the logic for the selection of the container and sealing system design and the development of innovative technologies for their manufacture including the use of laser welding, cold spray and pulsed-electrodeposition copper coating for the manufacture of the used fuel container, isostatic presses for the production of the one-piece bentonite blocks, and slip-skid technologies for placement into the repository. (author)

  11. Development of the Canadian used fuel repository engineered barrier system

    International Nuclear Information System (INIS)

    Hatton, C.

    2015-01-01

    The Nuclear Waste Management Organization (NWMO) is responsible for the implementation of Adaptive Phased Management (APM), the federally-approved plan for the safe long-term management of Canada's used nuclear fuel. Under the APM plan, used nuclear fuel will ultimately be placed within a deep geological repository in a suitable rock formation. In implementing APM, the NWMO is committed to ensure consistency with international best practices in the development of its repository system, including any advances in technology. In 2012, the NWMO undertook an optimization study to look at both the design and manufacture of its engineered barriers. This study looked at current technologies for the design and manufacture of used fuel containers, placement technologies, repository design, and buffer and sealing systems, while taking into consideration the state of the art worldwide in repository design and acceptance. The result of that study is the current Canadian engineered barrier system, consisting of a 2.7 tonne used fuel container with a carbon-steel core, copper-coated surface and welded spherical heads. The used fuel container is encapsulated in a bentonite buffer box at the surface and then transferred underground. Once underground, the used fuel is placed into a repository room which is cut into the rock using traditional drill-and-blast technologies. This paper explains the logic for the selection of the container and sealing system design and the development of innovative technologies for their manufacture including the use of laser welding, cold spray and pulsed-electrodeposition copper coating for the manufacture of the used fuel container, isostatic presses for the production of the one-piece bentonite blocks, and slip-skid technologies for placement into the repository. (author)

  12. Development of teaching material to integrate GT-POWER into combustion courses for IC engine simulations.

    Science.gov (United States)

    2009-02-01

    The main objective of this project was to develop instructional engineering projects that utilize the newly-offered PACE software GT-POWER for engine simulations in combustion-related courses at the Missouri University of Science and Technology. Stud...

  13. Testing and Development of a Shrouded Gas Turbine Engine in a Freejet Facility

    National Research Council Canada - National Science Library

    Garcia, Hector

    2000-01-01

    .... The combined cycle engine (CCE) could be incorporated into a variety of applications. The building of a new freejet facility and engine test rig at the Naval Postgraduate School enabled dynamic testing of the ongoing development of a turboramjet...

  14. Development status of rotary engine at Toyo Kogyo. [for general aviation aircraft

    Science.gov (United States)

    Yamamoto, K.

    1978-01-01

    Progress in the development of rotary engines which use a thermal reactor as the primary part of the exhaust emission control system is reviewed. Possibilities of further improvements in fuel economy of future rotary engines are indicated.

  15. Developing the curriculum for a new Bachelor's degree in Engineering for Sustainable Development

    NARCIS (Netherlands)

    Lozano, F.J.; Lozano, R.

    2013-01-01

    With a growing interest in sustainability, a number of universities have engaged in educating the future leaders, decision makers, scientists, and engineers on how their decisions can help societies become more sustainable. This paper presents the process for developing the Bachelor’s degree

  16. Developing the curriculum for a new Bachelor's degree in Engineering for Sustainable Development

    NARCIS (Netherlands)

    Lozano, Francisco J.; Lozano, Rodrigo

    2014-01-01

    With a growing interest in sustainability, a number of universities have engaged in educating the future leaders, decision makers, scientists, and engineers on how their decisions can help societies become more sustainable. This paper presents the process for developing the Bachelor's degree

  17. Evolution of the Systems Engineering Education Development (SEED) Program at NASA Goddard Space Flight Center

    Science.gov (United States)

    Bagg, Thomas C., III; Brumfield, Mark D.; Jamison, Donald E.; Granata, Raymond L.; Casey, Carolyn A.; Heller, Stuart

    2003-01-01

    The Systems Engineering Education Development (SEED) Program at NASA Goddard Space Flight Center develops systems engineers from existing discipline engineers. The program has evolved significantly since the report to INCOSE in 2003. This paper describes the SEED Program as it is now, outlines the changes over the last year, discusses current status and results, and shows the value of human systems and leadership skills for practicing systems engineers.

  18. Near Earth Asteroid Solar Sail Engineering Development Unit Test Program

    Science.gov (United States)

    Lockett, Tiffany Russell; Few, Alexander; Wilson, Richard

    2017-01-01

    The Near Earth Asteroid (NEA) Scout project is a 30x20x10cm (6U) cubesat reconnaissance mission to investigate a near Earth asteroid utilizing an 86m2 solar sail as the primary propulsion system. This will be the largest solar sail NASA will launch to date. NEA Scout is a secondary payload currently manifested on the maiden voyage of the Space Launch System in 2018. In development of the solar sail subsystem, design challenges were identified and investigated for packaging within a 6U form factor and deployment in cis-lunar space. Analysis furthered understanding of thermal, stress, and dynamics of the stowed system and matured an integrated sail membrane model for deployed flight dynamics. This paper will address design, fabrication, and lessons learned from the NEA Scout solar sail subsystem engineering development unit. From optical properties of the sail material to folding and spooling the single 86m2 sail, the team has developed a robust deployment system for the solar sail. This paper will also address expected and received test results from ascent vent, random vibration, and deployment tests.

  19. The Quantum Arnold Transformation for the damped harmonic oscillator: from the Caldirola-Kanai model toward the Bateman model

    Science.gov (United States)

    López-Ruiz, F. F.; Guerrero, J.; Aldaya, V.; Cossío, F.

    2012-08-01

    Using a quantum version of the Arnold transformation of classical mechanics, all quantum dynamical systems whose classical equations of motion are non-homogeneous linear second-order ordinary differential equations (LSODE), including systems with friction linear in velocity such as the damped harmonic oscillator, can be related to the quantum free-particle dynamical system. This implies that symmetries and simple computations in the free particle can be exported to the LSODE-system. The quantum Arnold transformation is given explicitly for the damped harmonic oscillator, and an algebraic connection between the Caldirola-Kanai model for the damped harmonic oscillator and the Bateman system will be sketched out.

  20. The Quantum Arnold Transformation for the damped harmonic oscillator: from the Caldirola-Kanai model toward the Bateman model

    International Nuclear Information System (INIS)

    López-Ruiz, F F; Guerrero, J; Aldaya, V; Cossío, F

    2012-01-01

    Using a quantum version of the Arnold transformation of classical mechanics, all quantum dynamical systems whose classical equations of motion are non-homogeneous linear second-order ordinary differential equations (LSODE), including systems with friction linear in velocity such as the damped harmonic oscillator, can be related to the quantum free-particle dynamical system. This implies that symmetries and simple computations in the free particle can be exported to the LSODE-system. The quantum Arnold transformation is given explicitly for the damped harmonic oscillator, and an algebraic connection between the Caldirola-Kanai model for the damped harmonic oscillator and the Bateman system will be sketched out.

  1. Advanced Gasoline Turbocharged Direction Injection (GTDI) Engine Development

    Energy Technology Data Exchange (ETDEWEB)

    Wagner, Terrance [Ford Motor Co., Dearborn, MI (United States)

    2015-12-31

    This program was undertaken in response to US Department of Energy Solicitation DE-FOA-0000079, resulting in a cooperative agreement with Ford and MTU to demonstrate improvement of fuel efficiency in a vehicle equipped with an advanced GTDI engine. Ford Motor Company has invested significantly in GTDI engine technology as a cost effective, high volume, fuel economy solution, marketed globally as EcoBoost technology. Ford envisions additional fuel economy improvement in the medium and long term by further advancing EcoBoost technology. The approach for the project was to engineer a comprehensive suite of gasoline engine systems technologies to achieve the project objectives, and to progressively demonstrate the objectives via concept analysis / computer modeling, single-cylinder and multi-cylinder engine testing on engine dynamometer, and vehicle level testing on chassis rolls.

  2. Using the Engineering Design Cycle to Develop Integrated Project Based Learning in Aerospace Engineering

    NARCIS (Netherlands)

    Saunders-Smits, G.N.; Roling, P.; Brügemann, V.; Timmer, N.; Melkert, J.

    2012-01-01

    Over the past four years the Faculty of Aerospace Engineering at Delft University of Technology in the Netherlands has redeveloped its BSc curriculum to mimic an engineering design cycle. Each semester represents a step in the design cycle: exploration; system design; sub-system design; test,

  3. Development of Simulator Maintenance Engineer Qualification Program Draft

    International Nuclear Information System (INIS)

    Chung, Kyung Hun

    2010-01-01

    As of 2009, KHNP has currently seven full scope simulators that are used for training of Nuclear Power Plant (NPP) Operators. Well-trained Simulator Maintenance Engineers (SME) are required to support these simulators. These SMEs will maintain and address any issues identified or any changes required for keep up the simulator with their respective plant sites. These issues will be identified as Simulator Discrepancy Reports (DR) or Work Order (WO) by the simulator operation personnel in KHNP. The simulator maintenance is a very complex. The simulator consists of many areas of process and requires experts in software modeling for different processes such as Neutronics, thermohydraulics, Logics, control, Electrical systems and computer systems as well as hardware subjects such as I and C, I/O, computers, etc. All these areas need experts the subject expertise need to be divided among SME's. In other word the SME's need to be trained for different expertise as well as having different level of SME's. KHNP has seen the need to outsource the maintenance work for these complex simulators. To have one company concentrating on this work will have many benefits such as: · Provides proper and well trained experts · Maintains consistent support personnel · Maintains the maintenance history for the simulator · Coordinates and Maintains the knowledge in house · The simulator maintenance will be consistent In order to accomplish the goals, KEPCO RI has recognized that there is a need for a program to adequately train and qualify the SME's. KEPCO RI and GSE, which has provided 6 simulators among 7 NPP simulators in Korea, have jointly developed this Simulator Maintenance Engineer Qualification Program (SMEQP). After issue of this plan, KEPCO RI will maintain and modify as needed periodically to meet the goals and purpose of the plan

  4. Experience of Developing a Meta-Semantic Search Engine

    OpenAIRE

    Mukhopadhyay, Debajyoti; Sharma, Manoj; Joshi, Gajanan; Pagare, Trupti; Palwe, Adarsha

    2013-01-01

    Thinking of todays web search scenario which is mainly keyword based, leads to the need of effective and meaningful search provided by Semantic Web. Existing search engines are vulnerable to provide relevant answers to users query due to their dependency on simple data available in web pages. On other hand, semantic search engines provide efficient and relevant results as the semantic web manages information with well defined meaning using ontology. A Meta-Search engine is a search tool that ...

  5. A Chaotic Cryptosystem for Images Based on Henon and Arnold Cat Map

    Science.gov (United States)

    Sundararajan, Elankovan

    2014-01-01

    The rapid evolution of imaging and communication technologies has transformed images into a widespread data type. Different types of data, such as personal medical information, official correspondence, or governmental and military documents, are saved and transmitted in the form of images over public networks. Hence, a fast and secure cryptosystem is needed for high-resolution images. In this paper, a novel encryption scheme is presented for securing images based on Arnold cat and Henon chaotic maps. The scheme uses Arnold cat map for bit- and pixel-level permutations on plain and secret images, while Henon map creates secret images and specific parameters for the permutations. Both the encryption and decryption processes are explained, formulated, and graphically presented. The results of security analysis of five different images demonstrate the strength of the proposed cryptosystem against statistical, brute force and differential attacks. The evaluated running time for both encryption and decryption processes guarantee that the cryptosystem can work effectively in real-time applications. PMID:25258724

  6. Management of uncommon secondary trigeminal neuralgia related to a rare Arnold Chiari type I malformation

    Directory of Open Access Journals (Sweden)

    Zafar Ali Khan

    2017-12-01

    Full Text Available Background Trigeminal neuralgia (TN may sometimes present secondary to an intra-cranial cause. Arnold Chiari Malformation (ACM is downward herniation of the cerebellar tonsils through the foramen magnum that may be a cause of TN like pain in very rare cases. Aims The aim of this brief report is to suggest the proper management of uncommon secondary trigeminal neuralgia related to a rare Arnold Chiari type I malformation. Methods A male patient presented electric shock like stabbing pain on the right side of the face for more than ten years. The symptoms were typical of trigeminal neuralgia except that there was loss of corneal reflex on the right side and the patient also complained of gait & sleep disturbances. Complex and multilevel diagnosis was made. Results A multiplanar imaging through brain acquiring T1/T2W1 revealed ACM Type I Malformation with caudal displacement of cerebellar tonsils through foramen magnum. Conclusion Dental surgeons and oral and Maxillofacial Surgeons should exclude intra-cranial causes by Magnetic Resonance Imaging(MRI in patients of TN presenting with loss of corneal reflex, gait and sleep disturbances due to night time pain episodes.

  7. A Novel Image Encryption Based on Algebraic S-box and Arnold Transform

    Science.gov (United States)

    Farwa, Shabieh; Muhammad, Nazeer; Shah, Tariq; Ahmad, Sohail

    2017-09-01

    Recent study shows that substitution box (S-box) only cannot be reliably used in image encryption techniques. We, in this paper, propose a novel and secure image encryption scheme that utilizes the combined effect of an algebraic substitution box along with the scrambling effect of the Arnold transform. The underlying algorithm involves the application of S-box, which is the most imperative source to create confusion and diffusion in the data. The speciality of the proposed algorithm lies, firstly, in the high sensitivity of our S-box to the choice of the initial conditions which makes this S-box stronger than the chaos-based S-boxes as it saves computational labour by deploying a comparatively simple and direct approach based on the algebraic structure of the multiplicative cyclic group of the Galois field. Secondly the proposed method becomes more secure by considering a combination of S-box with certain number of iterations of the Arnold transform. The strength of the S-box is examined in terms of various performance indices such as nonlinearity, strict avalanche criterion, bit independence criterion, linear and differential approximation probabilities etc. We prove through the most significant techniques used for the statistical analyses of the encrypted image that our image encryption algorithm satisfies all the necessary criteria to be usefully and reliably implemented in image encryption applications.

  8. Success of Arnol'd's method in hierarchy of ocean models

    International Nuclear Information System (INIS)

    Ripa, P.

    1993-01-01

    The method of Arnol'd is used to derive stability conditions of Hamiltonian systems with singular Poisson brackets; notably, those of fluid mechanics. Let the field(s) var-phi(x,t) represent the state variables, and Hamiltonian H [var-phi] and Poisson bracket (.,.) be such that ∂ t var-phi = (var-phi, H). The bracket must have the usual properties; in addition, it may be singular, i.e. there may exist non-trivial functional(s) of state C(var-phi) - called Casimir(s) - such that (C,F) ≡ 0, for any admissible functional of state F(var-phi). Arnol'd's theorms on stability are applied to put constraints on the solutions var-phi(x,t). This model is then applied to the problem of circulation within ocean models, in particular to two families of classical ocean models, primitive equations (PEN) and quasi-geostrophic (QGM) models. These models are layered vertical structures with top and bottom boundaries which may be either rigid or free

  9. Theology of Arnold of Villanova: between Bible and politics

    Directory of Open Access Journals (Sweden)

    Bogusław Kochaniewicz

    2011-09-01

    Full Text Available Biblical interpretation of Arnold of Villanova manifests us not only a specific and particular current of exegesis within 14th century. He emphasised the idea of eschaton fullfilled, manifested through the history more and more clear and perfect. His exegesis, based on Joachim de Fiore’s work presented the Bible as an instrument of the historical knowledge. The Bible, interpreted in allegorical perspective, manifested the meaning of the events pasted and presents and future. In order that Bible could be always actual, it required miracles and apparitions, which would support and manifest extraordinary divine interventions within the history of the world. In Arnold’s opinion, the Bible, without miracles and mistical experiences, could lost its own meaning. Arnold of Villanova, being inspired by the Franciscan spiritual movement, strived to evidence the ideas of the nearness of the end of the world. Even if he was not an eminent theologian, he impressed and inspired his epoch. Therefore his name is mentioned by the manuals of the history of theology.

  10. Development of REFLA/TRAC code for engineering work station

    International Nuclear Information System (INIS)

    Ohnuki, Akira; Akimoto, Hajime; Murao, Yoshio

    1994-03-01

    The REFLA/TRAC code is a best-estimate code which is expected to check reactor safety analysis codes for light water reactors (LWRs) and to perform accident analyses for LWRs and also for an advanced LWR. Therefore, a high predictive capability is required and the assessment of each physical model becomes important because the models govern the predictive capability. In the case of the assessment of three-dimensional models in REFLA/TRAC code, a conventional large computer is being used and it is difficult to perform the assessment efficiently because the turnaround time for the calculation and the analysis is long. Then, a REFLA/TRAC code which can run on an engineering work station (EWS) was developed. Calculational speed of the current EWS is the same order as that of large computers and the EWS has an excellent function for multidimensional graphical drawings. Besides, the plotting processors for X-Y drawing and for two-dimensional graphical drawing were developed in order to perform efficient analyses for three-dimensional calculations. In future, we can expect that the assessment of three-dimensional models becomes more efficient by introducing an EWS with higher calculational speed and with improved graphical drawings. In this report, each outline for the following three programs is described: (1) EWS version of REFLA/TRAC code, (2) Plot processor for X-Y drawing and (3) Plot processor for two-dimensional graphical drawing. (author)

  11. Application of software engineering to development of reactor-safety codes

    International Nuclear Information System (INIS)

    Wilburn, N.P.; Niccoli, L.G.

    1980-11-01

    As a result of the drastically increasing cost of software and the lack of an engineering approach, the technology of Software Engineering is being developed. Software Engineering provides an answer to the increasing cost of developing and maintaining software. It has been applied extensively in the business and aerospace communities and is just now being applied to the development of scientific software and, in particular, to the development of reactor safety codes at HEDL

  12. Development of fuel economy 5W-20 gasoline engine oil; Teinenpi 5W-20 gasoline engine yu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Akiyama, K; Ueda, F; Kurono, K; Kawai, H; Sugiyama, S [Toyota Motor Corp., Aichi (Japan)

    1997-10-01

    A 5W-20 gasoline engine oil which improves vehicle fuel efficiency by more than 1.5% relative to a conventional 5W-30 gasoline engine oil was newly developed. Its high fuel economy performance lasts 10,000 km. The viscosity was optimized to satisfy both fuel economy and antiwear performances. Thiadiazole was used to retain the initial fuel economy performance provided by MoDTC. 5 refs., 7 figs., 2 tabs.

  13. Developing Systems Engineering Skills Through NASA Summer Intern Project

    Science.gov (United States)

    Bhasin, Kul; Barritt, Brian; Golden, Bert; Knoblock, Eric; Matthews, Seth; Warner, Joe

    2010-01-01

    During the Formulation phases of the NASA Project Life Cycle, communication systems engineers are responsible for designing space communication links and analyzing their performance to ensure that the proposed communication architecture is capable of satisfying high-level mission requirements. Senior engineers with extensive experience in communications systems perform these activities. However, the increasing complexity of space systems coupled with the current shortage of communications systems engineers has led to an urgent need for expedited training of new systems engineers. A pilot program, in which college-bound high school and undergraduate students studying various engineering disciplines are immersed in NASA s systems engineering practices, was conceived out of this need. This rapid summerlong training approach is feasible because of the availability of advanced software and technology tools and the students inherent ability to operate such tools. During this pilot internship program, a team of college-level and recently-hired engineers configured and utilized various software applications in the design and analysis of communication links for a plausible lunar sortie mission. The approach taken was to first design the direct-to-Earth communication links for the lunar mission elements, then to design the links between lunar surface and lunar orbital elements. Based on the data obtained from these software applications, an integrated communication system design was realized and the students gained valuable systems engineering knowledge. This paper describes this approach to rapidly training college-bound high school and undergraduate engineering students from various disciplines in NASA s systems engineering practices and tools. A summary of the potential use of NASA s emerging systems engineering internship program in broader applications is also described.

  14. Idaho National Engineering Laboratory decontamination and decommissioning robotics development program

    International Nuclear Information System (INIS)

    McKay, M.D.

    1993-04-01

    As part of the Idaho National Engineering Laboratory (INEL) Robotics Technology Development Program (RTDP) Decontamination ampersand Decommissioning (D ampersand D) robotics program, a task was designed to integrate the plasma arc cutting technology being developed under the Waste Facility Operations (WFO) robotics program into D ampersand D cutting applications. The plasma arc cutting technology is based upon the use of a high energy plasma torch to cut metallic objects. Traditionally, D ampersand D workers removing equipment and processes from a facility have used plasma arc cutting to accomplish this task. The worker is required to don a protective suit to shield from the high electromagnetic energy released from the cutting operation. Additionally, the worker is required to don protective clothing to shield against the radioactive materials and contamination. This protective clothing can become restrictive and cumbersome to work in. Because some of the work areas contain high levels of radiation, the worker is not allowed to dwell in the environment for sustained periods of time. To help alleviate some of the burdens required to accomplish this task, reduce or eliminate the safety hazardous to the worker, and reduce the overall cost of remediation, a program was established though the Office of Technology Development (OTD) to design and develop a robotic system capable of performing cutting operations using a plasma arc torch. Several D ampersand D tasks were identified having potential for use of the plasma arc cutting technology. The tasks listed below were chosen to represent common D ampersand D type activities where the plasma arc cutting technology can be applied

  15. Roles of plasma neutron source reactor in development of fusion reactor engineering: Comparison with fission reactor engineering

    International Nuclear Information System (INIS)

    Hirayama, Shoichi; Kawabe, Takaya

    1995-01-01

    The history of development of fusion power reactor has come to a turning point, where the main research target is now shifting from the plasma heating and confinement physics toward the burning plasma physics and reactor engineering. Although the development of fusion reactor system is the first time for human beings, engineers have experience of development of fission power reactor. The common feature between them is that both are plants used for the generation of nuclear reactions for the production of energy, nucleon, and radiation on an industrial scale. By studying the history of the development of the fission reactor, one can find the existence of experimental neutron reactors including irradiation facilities for fission reactor materials. These research neutron reactors played very important roles in the development of fission power reactors. When one considers the strategy of development of fusion power reactors from the points of fusion reactor engineering, one finds that the fusion neutron source corresponds to the neutron reactor in fission reactor development. In this paper, the authors discuss the roles of the plasma-based neutron source reactors in the development of fusion reactor engineering, by comparing it with the neutron reactors in the history of fission power development, and make proposals for the strategy of the fusion reactor development. 21 refs., 6 figs

  16. Project-organized learning and the development of competences in Engineering Education for Sustainable Development

    DEFF Research Database (Denmark)

    Guerra, Aida; Holgaard, Jette Egelund; Kolmos, Anette

    2013-01-01

    by the complex and economically driven society and develop innovative technologies to solve and prevent sustainable problems. In this perspective, ESD experts have stressed sustainability aspects as well as cross-disciplinary competences, such as inter-disciplinarity, adaptability, problem solving, critical...... thinking, systems thinking, etc. It is argued that Problem-Based Learning (PBL) provides a suitable framework for developing the competences mentioned, but there is a lack of studies that investigate the room which PBL practice leaves for ESD. In this study, we aim to investigate the staff’s perception......The integration of Education for Sustainable Development (ESD) principles has been claimed for all levels and areas of formal education. The integration of new kinds of competences, skills and knowledge into the engineering curricula aims to prepare future engineers to face the challenges posed...

  17. Research and development of turbo engines in HYPR project. Choonsoku yusokiyo suishin system no kenkyu kaihatsu ni okeru turbo kei engine no shisaku

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, Y; Itahara, H; Kohara, S [Ishikawajima-Harima Heavy Industries, Co. Ltd., Tokyo (Japan)

    1994-05-01

    The present paper outlined the project which aimed at developing a combined cycle engine by a combination of turbojet engine operable from the takeoff or landing to Mach 3 and ramjet engine operable from Mach 2.5 to 5. The outline included the test result report of a prototypical engine which was the main subject of project. Upon conceptual research on the engine to comply with the future supersonic passenger plane, a variable cycle engine jointly equipped with a mixer/ejector noise lowering device was applied as a turbojet engine to lower the noise. The prototypical turbojet engine which was a target engine subscaled to about 1/10 in thrust aimed at demonstrating the total system performance of the turbojet engine which structured a combined cycle engine. Prior to testing the above prototype, the core engine was singly tested (in Phase 1) with a confirmed good result in firing and startup characteristics. 4 refs., 9 figs., 3 tabs.

  18. Development of a Dynamic Engine Brake Model for Control Purposes

    NARCIS (Netherlands)

    Seykens, X.L.J.; Baert, R.S.G.; Willems, F.P.T.; Vink, W.; van den Heuvel, I.T.M.

    2006-01-01

    This paper presents the extension of an existing mean value dynamic engine model with new models for the combination of a compression release brake and an exhaust valve brake. The focus is on the prediction of engine brake torque, exhaust gas temperatures and mass flow rates. The implemented models

  19. Development of a dynamic engine brake model for control purposes

    NARCIS (Netherlands)

    Seykens, X.L.J.; Baert, R.S.G.; Willems, F.P.T.; Vink, W.; van den Heuvel, I.T.M.; Corde, G.

    2007-01-01

    This paper presents the extension of an existing mean value dynamic engine model with new models for the combination of a compression release brake and an exhaust valve brake. The focus is on the prediction of engine brake torque, exhaust gas temperatures and mass flow rates. The implemented models

  20. Current Developments in the French Engineering Education System

    Science.gov (United States)

    Lemaître, Denis

    2017-01-01

    The French engineering education system has been established in quite a different way from others in Europe, such as the German and British systems, for instance. Due to both the whole state system and the private initiatives during the industrial revolution, the engineering education system today is composed of a large number (nearly 200) of…

  1. Development of a Taxonomy of Keywords for Engineering Education Research

    Science.gov (United States)

    Finelli, Cynthia J.; Borrego, Maura; Rasoulifar, Golnoosh

    2016-01-01

    The diversity of engineering education research provides an opportunity for cross-fertilisation of ideas and creativity, but it also can result in fragmentation of the field and duplication of effort. One solution is to establish a standardised taxonomy of engineering education terms to map the field and communicate and connect research…

  2. System Design and Engineering, lubricating multidisciplinary development projects

    NARCIS (Netherlands)

    Bonnema, Gerrit Maarten; Veenvliet, Karel; Broenink, Johannes F.

    This text book introduces systems engineering for designing systems in multidisciplinary projects. First an overview of the systems engineering process is given. Several systems thinking tracks are presented, to think about the system in a number of ways, its context, its user, its functionality,

  3. Arnold Sommerfeld

    Indian Academy of Sciences (India)

    IAS Admin

    After another year for a teaching diploma, and then a year of military service, he moved in ... He gave the first ever courses on relativity and quantum theory as he was ... Hearty congratulations on your fine discovery and best regards, yours,.

  4. Arnold Sommerfeld

    Indian Academy of Sciences (India)

    IAS Admin

    The German tradition in physics – as in music, philosophy and literature – has been an exceptional one over a very long period of time. Recall the likes of Gustav Kirchhoff, Hermann von Helmholtz, Heinrich Hertz and Wilhelm Röntgen during the 19th century; to be followed by Max Planck, Wilhelm Wien, Albert Einstein, ...

  5. Arnold Rüütel : kui lapsi ei sünni, kes siis Eesti ühiskonnas väärtusi loob? / Arnold Rüütel ; intervjueerinud Kärt Karpa

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2007-01-01

    President Arnold Rüütel vastab küsimustele, mis puudutavad tema praegust tegevust, Eestis taasiseseisvumise järel tehtud vigu, maapiirkondade kõrvalejäämist, Eesti poliitika ideoloogia muutumist taasiseseisvumisest alates, suhtumist ülemnõukogu saadikuisse, pronksööd, Rahvaliitu, suhtumist Rahvaliidu ja SDE võimalikku ühinemisse

  6. Software Engineering Research/Developer Collaborations (C104)

    Science.gov (United States)

    Shell, Elaine; Shull, Forrest

    2005-01-01

    The goal of this collaboration was to produce Flight Software Branch (FSB) process standards for software inspections which could be used across three new missions within the FSB. The standard was developed by Dr. Forrest Shull (Fraunhofer Center for Experimental Software Engineering, Maryland) using the Perspective-Based Inspection approach, (PBI research has been funded by SARP) , then tested on a pilot Branch project. Because the short time scale of the collaboration ruled out a quantitative evaluation, it would be decided whether the standard was suitable for roll-out to other Branch projects based on a qualitative measure: whether the standard received high ratings from Branch personnel as to usability and overall satisfaction. The project used for piloting the Perspective-Based Inspection approach was a multi-mission framework designed for reuse. This was a good choice because key representatives from the three new missions would be involved in the inspections. The perspective-based approach was applied to produce inspection procedures tailored for the specific quality needs of the branch. The technical information to do so was largely drawn through a series of interviews with Branch personnel. The framework team used the procedures to review requirements. The inspections were useful for indicating that a restructuring of the requirements document was needed, which led to changes in the development project plan. The standard was sent out to other Branch personnel for review. Branch personnel were very positive. However, important changes were identified because the perspective of Attitude Control System (ACS) developers had not been adequately represented, a result of the specific personnel interviewed. The net result is that with some further work to incorporate the ACS perspective, and in synchrony with the roll out of independent Branch standards, the PBI approach will be implemented in the FSB. Also, the project intends to continue its collaboration with

  7. Engineered nanomaterials for plant growth and development: A perspective analysis.

    Science.gov (United States)

    Verma, Sandeep Kumar; Das, Ashok Kumar; Patel, Manoj Kumar; Shah, Ashish; Kumar, Vinay; Gantait, Saikat

    2018-07-15

    With the overwhelmingly rapid advancement in the field of nanotechnology, the engineered nanomaterials (ENMs) have been extensively used in various areas of the plant system, including quality improvement, growth and nutritional value enhancement, gene preservation etc. There are several recent reports on the ENMs' influence on growth enhancements, growth inhibition as well as certain toxic impacts on plant. However, translocation, growth responses and stress modulation mechanisms of ENMs in the plant systems call for better and in-depth understanding. Herein, we are presenting a comprehensive and critical account of different types of ENMs, their applications and their positive, negative and null impacts on physiological and molecular aspects of plant growth, development and stress responses. Recent reports revealed mixed effects on plants, ranging from enhanced crop yield, epi/genetic alterations, and phytotoxicity, resulting from the ENMs' exposure. Creditable research in recent years has revealed that the effects of ENMs on plants are species specific and are variable among plant species. ENM exposures are reported to trigger free radical formation, responsive scavenging, and antioxidant armories in the exposed plants. The ENMs are also reported to induce aberrant expressions of microRNAs, the key post-transcriptional regulators of plant growth, development and stress-responses of plants. However, these modulations, if judiciously done, may lead to improved plant growth and yield. A better understanding of the interactions between ENMs and plant responses, including their uptake transport, internalization, and activity, could revolutionize crop production through increased disease resistance, nutrient utilization, and crop yield. Therefore, in this review, we are presenting a critical account of the different selected ENMs, their uptake by the plants, their positive/negative impacts on plant growth and development, along with the resultant ENM-responsive post

  8. Development of the environmental management integrated baseline at the Idaho National Engineering Laboratory using systems engineering

    International Nuclear Information System (INIS)

    Murphy, J.A.; Caliva, R.M.; Wixson, J.R.

    1997-01-01

    The Idaho National Engineering Laboratory (INEL) is one of many Department of Energy (DOE) national laboratories that has been performing environmental cleanup and stabilization, which was accelerated upon the end of the cold war. In fact, the INEL currently receives two-thirds of its scope to perform these functions. However, the cleanup is a highly interactive system that creates an opportunity for systems engineering methodology to be employed. At the INEL, a group called EM (Environmental Management) Integration has been given this charter along with a small core of systems engineers. This paper discusses the progress to date of converting the INEL legacy system into one that uses the systems engineering discipline as the method to ensure that external requirements are met

  9. Coal-fueled high-speed diesel engine development: Task 2, Market assessment and economic analysis

    Energy Technology Data Exchange (ETDEWEB)

    Kakwani, R. M.; Wilson, Jr., R. P.; Winsor, R. E.

    1991-12-01

    Based on the preliminary coal engine design developed, this task was conducted to identify the best opportunity(s) to enter the market with the future coal-fueled, high-speed diesel engine. The results of this market and economic feasibility assessment will be used to determine what specific heavy duty engine application(s) are most attractive for coal fuel, and also define basic economic targets for the engine to be competitive.

  10. Waste treatment at the Radiochemical Engineering Development Center

    International Nuclear Information System (INIS)

    Brunson, R.R.; Bond, W.D.; Chattin, F.R.; Collins, R.T.; Sullivan, G.R.; Wiles, R.H.

    1997-01-01

    At the Radiochemical Engineering Development Center (REDC) irradiated targets are processed for the recovery of valuable radioisotopes, principally transuranium nuclides. A system was recently installed for treating the various liquid alkaline waste streams for removal of excess radioactive contaminants at the REDC. Radionuclides that are removed will be stored as solids and thus the future discharge of radionuclides to liquid low level waste tank storage will be greatly reduced. The treatment system is of modular design and is installed in a hot cell (Cubicle 7) in Building 7920 at the REDC where preliminary testing is in progress. The module incorporates the following: (1) a resorcinol-formaldehyde resin column for Cs removal, (2) a cross flow filtration unit for removal of rare earths and actinides as hydroxide, and (3) a waste solidification unit. Process flowsheets for operation of the module, key features of the module design, and its computer-assisted control system are presented. Good operability of the cross flow filter system is mandatory to the successful treatment of REDC wastes. Results of tests to date on the operation of the filter in its slurry collection mode and its slurry washing mode are presented. These tests include the effects of entrained organic solvent in the waste stream feed to the filter

  11. Linking Engineering and Medical Training: A USC program seeks to introduce medical and engineering students to medical device development.

    Science.gov (United States)

    Tolomiczenko, George; Sanger, Terry

    2015-01-01

    Medical students are attracted by the prospect of a meaningful addition to their clinical work. Engineering students are excited by a unique opportunity to learn directly alongside their medical student peers. For both, as well as the scientific community at large, the boutique program at the University of Southern California (USC) linking engineering and medical training at the graduate level is instructive of a new way of approaching engineering education that can potentially provide benefits to both students and society. Students who have grown up in an era of ?mass customization? in the retail and service industries can enjoy that same degree of flexibility also in the realm of education. At the same time, society gains engineers who have developed an increased empathy and awareness of the clinical contexts in which their innovations will be implemented.

  12. Development of a natural gas stratified charge rotary engine

    Energy Technology Data Exchange (ETDEWEB)

    Sierens, R.; Verdonck, W.

    1985-01-01

    A water model has been used to determine the positions of separate inlet ports for a natural gas, stratified charge rotary engine. The flow inside the combustion chamber (mainly during the induction period) has been registered by a film camera. From these tests the best locations of the inlet ports have been obtained, a prototype of this engine has been built by Audi NSU and tested in the laboratories of the university of Gent. The results of these tests, for different stratification configurations, are given. These results are comparable with the best results obtained by Audi NSU for a homogeneous natural gas rotary engine.

  13. Kas Arnold Rüütel valetas süümevannet andes? / Anneli Ammas, Garel Püüa

    Index Scriptorium Estoniae

    Ammas, Anneli, 1962-

    2006-01-01

    Autorite hinnangul tekib 31. augustil Eesti Ekspressis ilmunud artikli põhjal, milles käsitleti Johannes Hindi represseerimist, küsimus, kas Arnold Rüütel on valetanud Eesti Vabariigile korduvalt süümevannet andes. TÜ professori Kalle Meruski seisukoht. Lisa: Rüütel käskis kontrolli tugevdada

  14. Rüütel jäi kommunistinagi iseendaks / Arnold Rüütel ; intervjueerinud Hille Tänavsuu

    Index Scriptorium Estoniae

    Rüütel, Arnold, 1928-

    2001-01-01

    Arnold Rüütlile esitatud küsimused puudutavad tema minevikku, suhtumist noorte pahameeleavaldustesse pärast A. Rüütli valimist presidendiks, presidendi võimalusi mõjutada asjade käiku, president Lennart Merit, salaalkoholi leviku põhjusi jm. Parlamendisaadik

  15. Arnold Rüütel alustas oma Valgamaa visiiti Tõrvas ja Otepääl / Urve Sinisalu

    Index Scriptorium Estoniae

    Sinisalu, Urve, 1945-

    2002-01-01

    President Arnold Rüütli visiidist Valgamaale. Kohtumisest Tõrva Gümnaasiumi direktori Ivar Hanvere ja Tõrva linnapea Väino Tõemetsaga, külaskäigust Ants Tauli torupillitallu. Kommenteerib Ingrid Rüütel. Maakonnavisiit Valgamaale 23.-24.09.2002

  16. Recent Developments in Thiolated Polymeric Hydrogels for Tissue Engineering Applications.

    Science.gov (United States)

    Gajendiran, Mani; Rhee, Jae-Sung; Kim, Kyobum

    2018-02-01

    This review focuses on the recent strategy in the preparation of thiolated polymers and fabrication of their hydrogel matrices. The mechanism involved in the synthesis of thiolated polymers and fabrication of thiolated polymer hydrogels is exemplified with suitable schematic representations reported in the recent literature. The 2-iminothiolane namely "Traut's reagent" has been widely used for effectively thiolating the natural polymers such as collagen and gelatin, which contain free amino group in their backbone. The free carboxylic acid group containing polymers such as hyaluronic acid and heparin have been thiolated by using the bifunctional molecules such as cysteamine and L-cysteine via N-(3-dimethylaminopropyl)-N'-ethylcarbodiimide/N-hydroxysuccinimide (EDC/NHS) coupling reaction. The degree of thiolation in the polymer chain has been widely determined by using Ellman's assay method. The thiolated polymer hydrogels are prepared by disulfide bond formation (or) thiol-ene reaction (or) Michael-type addition reaction. The thiolated polymers such as thiolated gelatin are reacted with polyethylene glycol diacrylate for obtaining interpenetrating polymer network hydrogel scaffolds. Several in vitro cell culture experiments indicate that the developed thiolated polymer hydrogels exhibited biocompatibility and cellular mimicking properties. The developed hydrogel scaffolds efficiently support proliferation and differentiation of various cell types. In the present review article, the thiol-functionalized protein-based biopolymers, carbohydrate-based polymers, and some synthetic polymers have been covered with recently published research articles. In addition, the usage of new thiolated nanomaterials as a crosslinking agent for the preparation of three-dimensional tissue-engineered hydrogels is highlighted.

  17. Trend and future of diesel engine: Development of high efficiency and low emission low temperature combustion diesel engine

    International Nuclear Information System (INIS)

    Ho, R J; Yusoff, M Z; Palanisamy, K

    2013-01-01

    Stringent emission policy has put automotive research and development on developing high efficiency and low pollutant power train. Conventional direct injection diesel engine with diffused flame has reached its limitation and has driven R and D to explore other field of combustion. Low temperature combustion (LTC) and homogeneous charge combustion ignition has been proven to be effective methods in decreasing combustion pollutant emission. Nitrogen Oxide (NO x ) and Particulate Matter (PM) formation from combustion can be greatly suppressed. A review on each of method is covered to identify the condition and processes that result in these reductions. The critical parameters that allow such combustion to take place will be highlighted and serves as emphasis to the direction of developing future diesel engine system. This paper is written to explore potential of present numerical and experimental methods in optimizing diesel engine design through adoption of the new combustion technology.

  18. Trend and future of diesel engine: Development of high efficiency and low emission low temperature combustion diesel engine

    Science.gov (United States)

    Ho, R. J.; Yusoff, M. Z.; Palanisamy, K.

    2013-06-01

    Stringent emission policy has put automotive research & development on developing high efficiency and low pollutant power train. Conventional direct injection diesel engine with diffused flame has reached its limitation and has driven R&D to explore other field of combustion. Low temperature combustion (LTC) and homogeneous charge combustion ignition has been proven to be effective methods in decreasing combustion pollutant emission. Nitrogen Oxide (NOx) and Particulate Matter (PM) formation from combustion can be greatly suppressed. A review on each of method is covered to identify the condition and processes that result in these reductions. The critical parameters that allow such combustion to take place will be highlighted and serves as emphasis to the direction of developing future diesel engine system. This paper is written to explore potential of present numerical and experimental methods in optimizing diesel engine design through adoption of the new combustion technology.

  19. Development of a Comprehensive Digital Avionics Curriculum for the Aeronautical Engineer

    National Research Council Canada - National Science Library

    Hofer, Thomas W

    2006-01-01

    ... avionics curriculum does not yet exist that satisfies the needs of graduates who will serve as aeronautical engineers involved with the development, integration, testing, fielding, and supporting...

  20. Development of Novel Biodegradable Amino Acid Ester Based Polyphosphazene-Hydroxyapatite Composites for Bone Tissue Engineering

    National Research Council Canada - National Science Library

    Sethuraman, Swaminathan; Nair, Lakshmi S; Singh, Anurima; Bender, Jared D; Greish, Yaser E; Brown, Paul W; Allcock, H. R; Laurencin, Cato T

    2005-01-01

    .... CPCs are attractive candidates for the development of scaffolds for bone tissue engineering, since they are moldable, resorbable, set at physiological temperature without the use of toxic chemicals...

  1. Development of a Civil Engineer Corps Community Portal Prototype

    National Research Council Canada - National Science Library

    Rader, Neil

    2002-01-01

    The Civil Engineer Corps (CEC) is a relatively small Navy community consisting of approximately 1300 officers, Billet locations for the CEC range from Bahrain, Saudi Arabia to Keflavik, Iceland, CEC officers have a broad range...

  2. Development of CFD model for augmented core tripropellant rocket engine

    Science.gov (United States)

    Jones, Kenneth M.

    1994-10-01

    The Space Shuttle era has made major advances in technology and vehicle design to the point that the concept of a single-stage-to-orbit (SSTO) vehicle appears more feasible. NASA presently is conducting studies into the feasibility of certain advanced concept rocket engines that could be utilized in a SSTO vehicle. One such concept is a tripropellant system which burns kerosene and hydrogen initially and at altitude switches to hydrogen. This system will attain a larger mass fraction because LOX-kerosene engines have a greater average propellant density and greater thrust-to-weight ratio. This report describes the investigation to model the tripropellant augmented core engine. The physical aspects of the engine, the CFD code employed, and results of the numerical model for a single modular thruster are discussed.

  3. Risk communication strategy development using the aerospace systems engineering process

    Science.gov (United States)

    Dawson, S.; Sklar, M.

    2004-01-01

    This paper explains the goals and challenges of NASA's risk communication efforts and how the Aerospace Systems Engineering Process (ASEP) was used to map the risk communication strategy used at the Jet Propulsion Laboratory to achieve these goals.

  4. Weapon System Requirements: Detailed Systems Engineering Prior to Product Development Positions Programs for Success

    Science.gov (United States)

    2016-11-01

    modified, replaced, or sustained by consumers or different manufacturers in addition to the manufacturer that developed the system. It also allows...WEAPON SYSTEM REQUIREMENTS Detailed Systems Engineering Prior to Product Development Positions Programs for Success...Engineering Prior to Product Development Positions Programs for Success Why GAO Did This Study Cost and schedule growth in DOD major defense

  5. The Relationship of Personality Models and Development Tasks in Software Engineering

    OpenAIRE

    Wiesche, Manuel;Krcmar, Helmut

    2015-01-01

    Understanding the personality of software developers has been an ongoing topic in software engineering research. Software engineering researchers applied different theoretical models to understand software developers? personalities to better predict software developers? performance, orchestrate more effective and motivated teams, and identify the person that fits a certain job best. However, empirical results were found as contradicting, challenging validity, and missing guidance for IT perso...

  6. An Introduction to Sustainable Development in the Engineering Curriculum

    OpenAIRE

    Penlington, Roger; Steiner, Simon

    2014-01-01

    This resource was originally created by The Higher Education Academy Engineering Subject Centre. Authored by Roger Penlington and Simon Steiner, the Guide has been updated and is now released by the Centre for Engineering and Design Education at Loughborough University [http://cede.lboro.ac.uk] as an online resource with a companion resource compendium. This guide is intended to stimulate thought and consideration amongst those who: as members of teaching staff, may wish to introduce EngSD in...

  7. Development of compressed natural gas/diesel dual-fuel turbocharged compressed ignition engine

    Energy Technology Data Exchange (ETDEWEB)

    Shenghua, L.; Ziyan, W.; Jiang, R. [Xi' an Jiaotong Univ. (China). Dept. of Automotive Engineering

    2003-09-01

    A natural gas and diesel dual-fuel turbocharged compression ignition (CI) engine is developed to reduce emissions of a heavy-duty diesel engine. The compressed natural gas (CNG) pressure regulator is specially designed to feed back the boost pressure to simplify the fuel metering system. The natural gas bypass improves the engine response to acceleration. The modes of diesel injection are set according to the engine operating conditions. The application of honeycomb mixers changes the flowrate shape of natural gas and reduces hydrocarbon (HC) emission under low-load and lowspeed conditions. The cylinder pressures of a CI engine fuelled with diesel and dual fuel are analysed. The introduction of natural gas makes the ignition delay change with engine load. Under the same operating conditions, the emissions of smoke and NO{sub x} from the dual-fuel engine are both reduced. The HC and CO emissions for the dual-fuel engine remain within the range of regulation. (Author)

  8. Development of concept-based physiology lessons for biomedical engineering undergraduate students.

    Science.gov (United States)

    Nelson, Regina K; Chesler, Naomi C; Strang, Kevin T

    2013-06-01

    Physiology is a core requirement in the undergraduate biomedical engineering curriculum. In one or two introductory physiology courses, engineering students must learn physiology sufficiently to support learning in their subsequent engineering courses and careers. As preparation for future learning, physiology instruction centered on concepts may help engineering students to further develop their physiology and biomedical engineering knowledge. Following the Backward Design instructional model, a series of seven concept-based lessons was developed for undergraduate engineering students. These online lessons were created as prerequisite physiology training to prepare students to engage in a collaborative engineering challenge activity. This work is presented as an example of how to convert standard, organ system-based physiology content into concept-based content lessons.

  9. Internal combustion engine report: Spark ignited ICE GenSet optimization and novel concept development

    Energy Technology Data Exchange (ETDEWEB)

    Keller, J.; Blarigan, P. Van [Sandia National Labs., Livermore, CA (United States)

    1998-08-01

    In this manuscript the authors report on two projects each of which the goal is to produce cost effective hydrogen utilization technologies. These projects are: (1) the development of an electrical generation system using a conventional four-stroke spark-ignited internal combustion engine generator combination (SI-GenSet) optimized for maximum efficiency and minimum emissions, and (2) the development of a novel internal combustion engine concept. The SI-GenSet will be optimized to run on either hydrogen or hydrogen-blends. The novel concept seeks to develop an engine that optimizes the Otto cycle in a free piston configuration while minimizing all emissions. To this end the authors are developing a rapid combustion homogeneous charge compression ignition (HCCI) engine using a linear alternator for both power take-off and engine control. Targeted applications include stationary electrical power generation, stationary shaft power generation, hybrid vehicles, and nearly any other application now being accomplished with internal combustion engines.

  10. Effects of water stress on germination of Pinus nigra Arnold. seeds

    International Nuclear Information System (INIS)

    Topacoglu, O.; Sevik, H.; Akkuzu, E.

    2016-01-01

    Climate change, global warming and the deterioration of related environmental conditions cause an important problem for forest tree species. For this reason, it is necessary to determine the response of trees to these conditions. The Objective of this study was to investigate the effects of water stress on seed germination of fifteen Pinus nigra Arnold. provenances in Turkey. For this purpose, the water stresses between 0 and -8.0 bars were obtained using polyethylene glycol-6000 (PEG) solutions. Seeds were kept for 35 days at 20 ± 0.5 degree C. In this study, significant variations between the provenances were found. Ankara Uluhan ( percent 95, 08) and Isparta Tota ( percent 85, 41) provenances at -8.0 bars having the highest cumulative germination percentages were the most resistant provenances against the water stress. This study has shown that the water stress reduced the germination speed, germination percentage and germination value. (author)

  11. Action Movie in Election Day: Eraser (1996, Arnold Chwarzenegger and Other Politics Medias

    Directory of Open Access Journals (Sweden)

    Fabro Boaz Steibel

    2008-08-01

    Full Text Available This article aims to explore methodological frontiers between movie theory and political ommunication studies. When identifying traces of how politics, art and entertainment interact, it is possible to understand how movie celebrities can act as politicians, and vice versa. Arnold Schwarzenegger is a world famous actor who has twice won the Californian gubernatorial election. The principal purpose of this article is not to discuss political spectacle or analyse Schwarzenegger’s approach to government. The idea is to understand how a film in which Schwarzenegger starred over a decade ago (Eraser, 1996 has influenced his campaign image construction. The article’s methodological basis is a collective text by the Editors of Cahiers du Cinéma, based on John Ford’s Young Mr. Lincoln (1939. Its methodology allows us to observe important characteristics of Schwarzenegger’s role in the Eraser movie, which are then compared to the 2002 election scenario.

  12. Nuclear magnetic resonance (NMR) imaging of Arnold-Chiari type I malformation with hydromyelia

    International Nuclear Information System (INIS)

    DeLaPaz, R.L.; Brady, T.J.; Buonanno, F.S.; New, P.F.; Kistler, J.P.; McGinnis, B.D.; Pykett, I.L.; Taveras, J.M.

    1983-01-01

    Saturation recovery nuclear magnetic resonance (NMR) images and metrizamide computed tomography (CT) scans were obtained in an adult patient with a clinical history suggestive of syringomyelia. Both NMR and CT studies showed low lying cerebellar tonsils. The CT study demonstrated central cavitation of the spinal cord from the midthoracic to midcervical levels but could not exclude an intramedullary soft tissue mass at the cervico-medullary junction. The NMR images in transverse, coronal, and sagittal planes demonstrated extension of an enlarged central spinal cord cerebrospinal fluid space to the cervico-medullary junction. This was felt to be strong evidence for exclusion of an intramedullary soft tissue mass and in favor of a diagnosis of Arnold-Chiari Type I malformation with hydromyelia. The noninvasive nature of spinal cord and cervico-medullary junction evaluation with NMR is emphasized

  13. Unilateral phrenic nerve stimulation for neurogenic hypoventilation in Arnold Chiari malformation

    Directory of Open Access Journals (Sweden)

    Nitin Garg

    2013-01-01

    Full Text Available Long- term ventilator dependence in patients with neurogenic hypoventilation is associated with significant morbidity and restricts mobility. Diaphragmatic pacing by phrenic nerve stimulation (PNS is a viable alternative. This is a case report of patient with Arnold-Chiari malformation with extensive syrinx who had neurogenic hypoventilation during sleep even after foramen magnum decompression and resolution of the syrinx. Unilateral PNS was done using spinal cord stimulator. With intermittent stimulation for 8 h while asleep, patient could be weaned off the ventilator completely. At 2 years follow- up, patient is ambulant and has returned to his routine activities. PNS is a good treatment tool in patients with neurogenic hypoventilation. Spinal cord stimulator can be used with optimal results. This is first such reported case of using spinal cord stimulator for PNS from India.

  14. Anesthesia for a patient of acromesomelic dysplasia with associated hydrocephalus, Arnold Chiari malformation and syringomyelia

    Directory of Open Access Journals (Sweden)

    Rudrashish Haldar

    2013-01-01

    Full Text Available Acromesomelic dysplasias are autosomal recessive osteochondrodysplasias. Acromesomelic dysplasia Maroteaux-type (AMDM, also known as St Helena dysplasia, is of two types: The classical and the mild variety. About 50 cases of AMDM have been reported till date, most of them being the classical variety. There is scarcity of literature on anesthesia for such patients. We are reporting a case of general anesthetic management of AMDM, associated with hydrocephalus, Arnold Chiari malformation type-1 and syringomyelia. The patient was a 10-year-old short-statured boy who presented with symptomatic thoracic kyphoscoliosis, gibbus deformity and back pain. On examination, there was no neurological deficit. Radiology revealed thoracic kyphoscoliosis, mild ventriculomegaly and upper cervical syringomyelia. The patient underwent posterior fossa decompression in the prone position under general anesthesia. We will discuss the anesthetic considerations for such patients and review the pertinent literature.

  15. Association of HTLV-I with Arnold Chiari syndrome and syringomyelia

    Directory of Open Access Journals (Sweden)

    Graça Maria de Castro Viana

    Full Text Available HTLV-I is associated with a broad spectrum of manifestations, including tropical spastic paraparesis and adult T-cell leukemia/lymphoma. Arnold Chiari syndrome is a condition characterized by herniation of the cerebellar tonsils through the foramen magnum. This condition should be suspected in all patients with headache and impaired motor coordination. Syringomyelia is a developmental anomaly that leads to the formation of an intramedullary cavity. Its clinical presentation is classically characterized by syringomyelic dissociation of sensation, with suspended distribution in the proximal portion of the trunk and upper limbs and preservation in other regions. We report here a case of association of the three diseases, which is rare in clinical practice, illustrating the difficulty in the diagnosis and therapeutic management of these conditions.

  16. Analysis of materials of the mural painting 'Los Prometeos' of Arnold Belkin, Managua, Nicaragua

    International Nuclear Information System (INIS)

    Espinosa, M.E.; Tapia, M.

    2004-01-01

    Arnold Belkin was one of the most important exponents of the new muralism, in his paintings topics like war, dead, injustice, as well as hope, peace, society transformation and science benefits to the humankind were always related. One of these murals is the 'Los Prometeos' located at Managua, Nicaragua. This mural painting actually is suffering a localized deterioration by weather conditions (humidity) and manufacture techniques. Samples were collected from different spots of mural which shows the deterioration problem, in order to characterized them scanning electron microscopy, energy dispersive X-ray spectroscopy and X-ray diffraction were used to analyzed the soluble salts influences (sulfates and chlorides) in the deterioration mechanism problem. (Author) 9 refs., 10 tabs., 17 figs

  17. Development of Graduate Course Education by Industry Collaboration in Center for Engineering Education Development, CEED

    Science.gov (United States)

    Noguchi, Toru; Yoshikawa, Kozo; Nakamura, Masato; Kaneko, Katsuhiko

    New education programs for engineering graduate courses, and the achievements are described. Following the previous reports on overseas and domestic internship2) , 3) , this article states other common programs ; seminars on state of technologies in industries, practical English and internationalization programs, and a program to accept overseas internship students. E-learning system to assist off-campus students is also described. All these programs are developed and conducted by specialist professors invited from industries and national institutions, in collaboration with faculty professors. Students learn how the engineering science apply to the practical problems, acquire wider view and deeper understanding on industries, and gain abilities to act in global society including communication skill, those are not taught in classrooms and laboratories. Educational effects of these industry collaborated programs is significant to activate the graduate course education, although the comprehensive evaluation is the future subject.

  18. Defining project scenarios for the agile requirements engineering product-line development questionnaire

    OpenAIRE

    Feng, Kunwu; Lempert, Meli; Tang, Yan; Tian, Kun; Cooper, Kendra M.L.; Franch Gutiérrez, Javier

    2007-01-01

    Current agile methods are focused on practices of small, rapid developing and iteration, more people oriented, less documentation projects, and the use of the methods in large, product line projects are somehow difficult. UTD and GESSI have started a project to develop an expert system that can assist a requirements enginer in selecting a requirements engineering process that is well suited for their project, in particular with respect to the use of agile and product line engineering methods....

  19. Developing a survey to collect expertise in agile product line requirements engineering processes

    OpenAIRE

    Feng, Kunwu; Lempert, Meli; Tang, Yan; Tian, Kun; Cooper, Kendra M.L.; Franch Gutiérrez, Javier

    2007-01-01

    Current agile methods are focused on practices of small, rapid developing and iteration, more people oriented, less documentation projects, and the use of the methods in large, product line projects are somehow difficult. UTD and GESSI have started a project to develop an expert system that can assist a requirements enginer in selecting a requirements engineering process that is well suited for their project, in particular with respect to the use of agile and product line engineering methods....

  20. Development of Demonstrably Predictive Models for Emissions from Alternative Fuels Based Aircraft Engines

    Science.gov (United States)

    2017-05-01

    Engineering Chemistry Fundamentals, Vol. 5, No. 3, 1966, pp. 356–363. [14] Burns, R. A., Development of scalar and velocity imaging diagnostics...in an Aero- Engine Model Combustor at Elevated Pressure Using URANS and Finite- Rate Chemistry ,” 50th AIAA/ASME/SAE/ASEE Joint Propulsion Conference...FINAL REPORT Development of Demonstrably Predictive Models for Emissions from Alternative Fuels Based Aircraft Engines SERDP Project WP-2151

  1. Orofacial clinical features in Arnold Chiari type I malformation: A case series.

    Science.gov (United States)

    de Arruda, José-Alcides; Figueiredo, Eugênia; Monteiro, João-Luiz; Barbosa, Livia-Mirelle; Rodrigues, Cleomar; Vasconcelos, Belmiro

    2018-04-01

    Arnold Chiari malformation (ACM) is characterized by an anatomical defect at the base of the skull where the cerebellum and the spinal cord herniate through the foramen magnum into the cervical spinal canal. Among the subtypes of the condition, ACM type I (ACM-I) is particularly outstanding because of the severity of symptoms. This study aimed to analyze the orofacial clinical manifestations of patients with ACM-I, and discuss their demographic distribution and clinical features in light of the literature. A case series with patients with ACM-I treated between 2012 and 2015 was described. The sample consisted of patients who were referred by the Department of Neurosurgery to the Oral and Maxillofacial Surgery Service of Hospital da Restauração in Brazil for the assessment of facial symptomatology. A questionnaire was applied to evaluate the presence of painful orofacial findings. Data are reported using descriptive statistical methods. Mean patient age was 39.3 years and the sample consisted mostly of male patients. A high prevalence of headache (50%) and pain in the neck (66.7%) and masticatory muscles (50%) was found. Only one patient reported difficulty in performing mandibular movements and two reported jaw clicking sounds. Mean mouth opening was 40.83 mm. ACM-I patients may exhibit orofacial symptoms which may mimic temporomandibular joint disorders. This study brings interesting information that could help clinicians and oral and maxillofacial surgeons to understand this uncommon condition and also help with the diagnosis of patients with similar physical characteristics by referring them to a neurosurgeon. Key words: Arnold-Chiari malformation, facial pain, diagnosis, orofacial.

  2. Quantum color image watermarking based on Arnold transformation and LSB steganography

    Science.gov (United States)

    Zhou, Ri-Gui; Hu, Wenwen; Fan, Ping; Luo, Gaofeng

    In this paper, a quantum color image watermarking scheme is proposed through twice-scrambling of Arnold transformations and steganography of least significant bit (LSB). Both carrier image and watermark images are represented by the novel quantum representation of color digital images model (NCQI). The image sizes for carrier and watermark are assumed to be 2n×2n and 2n‑1×2n‑1, respectively. At first, the watermark is scrambled into a disordered form through image preprocessing technique of exchanging the image pixel position and altering the color information based on Arnold transforms, simultaneously. Then, the scrambled watermark with 2n‑1×2n‑1 image size and 24-qubit grayscale is further expanded to an image with size 2n×2n and 6-qubit grayscale using the nearest-neighbor interpolation method. Finally, the scrambled and expanded watermark is embedded into the carrier by steganography of LSB scheme, and a key image with 2n×2n size and 3-qubit information is generated at the meantime, which only can use the key image to retrieve the original watermark. The extraction of watermark is the reverse process of embedding, which is achieved by applying a sequence of operations in the reverse order. Simulation-based experimental results involving different carrier and watermark images (i.e. conventional or non-quantum) are simulated based on the classical computer’s MATLAB 2014b software, which illustrates that the present method has a good performance in terms of three items: visual quality, robustness and steganography capacity.

  3. Development of High Efficiency Clean Combustion Engine Designs for Spark-Ignition and Compression-Ignition Internal Combustion Engines

    Energy Technology Data Exchange (ETDEWEB)

    Marriott, Craig; Gonzalez, Manual; Russell, Durrett

    2011-06-30

    This report summarizes activities related to the revised STATEMENT OF PROJECT OBJECTIVES (SOPO) dated June 2010 for the Development of High-Efficiency Clean Combustion engine Designs for Spark-Ignition and Compression-Ignition Internal Combustion Engines (COOPERATIVE AGREEMENT NUMBER DE-FC26-05NT42415) project. In both the spark- (SI) and compression-ignition (CI) development activities covered in this program, the goal was to develop potential production-viable internal combustion engine system technologies that both reduce fuel consumption and simultaneously met exhaust emission targets. To be production-viable, engine technologies were also evaluated to determine if they would meet customer expectations of refinement in terms of noise, vibration, performance, driveability, etc. in addition to having an attractive business case and value. Prior to this activity, only proprietary theoretical / laboratory knowledge existed on the combustion technologies explored The research reported here expands and develops this knowledge to determine series-production viability. Significant SI and CI engine development occurred during this program within General Motors, LLC over more than five years. In the SI program, several engines were designed and developed that used both a relatively simple multi-lift valve train system and a Fully Flexible Valve Actuation (FFVA) system to enable a Homogeneous Charge Compression Ignition (HCCI) combustion process. Many technical challenges, which were unknown at the start of this program, were identified and systematically resolved through analysis, test and development. This report documents the challenges and solutions for each SOPO deliverable. As a result of the project activities, the production viability of the developed clean combustion technologies has been determined. At this time, HCCI combustion for SI engines is not considered production-viable for several reasons. HCCI combustion is excessively sensitive to control variables

  4. How Much Do Engineering Students Know about Sustainable Development? The Findings of an International Survey and Possible Implications for the Engineering Curriculum

    Science.gov (United States)

    Azapagic, Adisa; Perdan, Slobodan; Shallcross, David

    2005-01-01

    This paper addresses the issue of engineering education for sustainable development. In an attempt to facilitate a better integration of sustainability teaching into the engineering curriculum, it seeks to provide answers to the following fundamental questions: (1) How much do engineering students know about sustainable development? (2) What are…

  5. DNA Nanotechnology-Enabled Interfacial Engineering for Biosensor Development.

    Science.gov (United States)

    Ye, Dekai; Zuo, Xiaolei; Fan, Chunhai

    2018-06-12

    Biosensors represent biomimetic analytical tools for addressing increasing needs in medical diagnosis, environmental monitoring, security, and biodefense. Nevertheless, widespread real-world applications of biosensors remain challenging due to limitations of performance, including sensitivity, specificity, speed, and reproducibility. In this review, we present a DNA nanotechnology-enabled interfacial engineering approach for improving the performance of biosensors. We first introduce the main challenges of the biosensing interfaces, especially under the context of controlling the DNA interfacial assembly. We then summarize recent progress in DNA nanotechnology and efforts to harness DNA nanostructures to engineer various biological interfaces, with a particular focus on the use of framework nucleic acids. We also discuss the implementation of biosensors to detect physiologically relevant nucleic acids, proteins, small molecules, ions, and other biomarkers. This review highlights promising applications of DNA nanotechnology in interfacial engineering for biosensors and related areas.

  6. PBL and CDIO: complementary models for engineering education development

    Science.gov (United States)

    Edström, Kristina; Kolmos, Anette

    2014-09-01

    This paper compares two models for reforming engineering education, problem/project-based learning (PBL), and conceive-design-implement-operate (CDIO), identifying and explaining similarities and differences. PBL and CDIO are defined and contrasted in terms of their history, community, definitions, curriculum design, relation to disciplines, engineering projects, and change strategy. The structured comparison is intended as an introduction for learning about any of these models. It also invites reflection to support the understanding and evolution of PBL and CDIO, and indicates specifically what the communities can learn from each other. It is noted that while the two approaches share many underlying values, they only partially overlap as strategies for educational reform. The conclusions are that practitioners have much to learn from each other's experiences through a dialogue between the communities, and that PBL and CDIO can play compatible and mutually reinforcing roles, and thus can be fruitfully combined to reform engineering education.

  7. Survey on the technological development issues for large-scale methanol engine power generation plant; Ogata methanol engine hatsuden plant ni kansuru gijutsu kaihatsu kadai chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Based on the result of `Survey on the feasibility of large-scale methanol engine power generation plant` in fiscal 1992, concrete technological development issues were studied for its practical use, and the technological R & D scheme was prepared for large-scale methanol engine power plant featured by low NOx and high efficiency. Technological development issues of this plant were as follows: improvement of thermal efficiency, reduction of NOx emission, improvement of the reliability and durability of ignition and fuel injection systems, and reduction of vibration. As the economical effect of the technological development, the profitability of NOx control measures was compared between this methanol engine and conventional heavy oil diesel engines or gas engines. As a result, this engine was more economical than conventional engines. It was suggested that development of the equipment will be completed in nearly 4 years through every component study, single-cylinder model experiment and real engine test. 21 refs., 43 figs., 19 tabs.

  8. Development of a Systems Engineering Model of the Chemical Separations Process

    International Nuclear Information System (INIS)

    Sun, Lijian; Li, Jianhong; Chen, Yitung; Clarksean, Randy; Ladler, Jim; Vandergrift, George

    2002-01-01

    Work is being performed to develop a general-purpose systems engineering model for the AAA separation process. The work centers on the development of a new user interface for the AMUSE code and on the specification of a systems engineering model. This paper presents background information and an overview of work completed to date. (authors)

  9. Development and engineering application of rotating drum acid-curing equipment in uranium mills

    International Nuclear Information System (INIS)

    Liu Wenhua

    2006-01-01

    The development and engineering application of rotating drum acid-curing equipment for 'strong acid-curing and ferri-trickle leaching' process are introduced, including the design of main structure, problems appeared in the development and engineering application, and methods solved. (authors)

  10. How to Educate Engineers for/in Sustainable Development: Ten Years of Discussion, Remaining Challenges

    Science.gov (United States)

    Mulder, Karel F.; Segalas, Jordi; Ferrer-Balas, Didac

    2012-01-01

    Purpose: The purpose of this paper is to analyse the process of changing engineering universities towards sustainable development (SD). It outlines the types of changes needed, both in respect of approaches, visions, philosophies and cultural change, which are crucial for engineering universities which want to implement sustainable development as…

  11. Development and Application of a Systems Engineering Framework to Support Online Course Design and Delivery

    Science.gov (United States)

    Bozkurt, Ipek; Helm, James

    2013-01-01

    This paper develops a systems engineering-based framework to assist in the design of an online engineering course. Specifically, the purpose of the framework is to provide a structured methodology for the design, development and delivery of a fully online course, either brand new or modified from an existing face-to-face course. The main strength…

  12. Development of Nuclear Engineering Educational Program at Ibaraki University with Regional Collaboration

    Science.gov (United States)

    Matsumura, Kunihito; Kaminaga, Fumito; Kanto, Yasuhiro; Tanaka, Nobuatsu; Saigusa, Mikio; Kikuchi, Kenji; Kurumada, Akira

    The College of Engineering, Ibaraki University is located at the Hitachi city, in the north part of Ibaraki prefecture. Hitachi and Tokai areas are well known as concentration of advanced technology center of nuclear power research organizations. By considering these regional advantages, we developed a new nuclear engineering educational program for students in the Collage of Engineering and The Graduate School of Science and Engineering of Ibaraki University. The program is consisted of the fundamental lectures of nuclear engineering and nuclear engineering experiments. In addition, several observation learning programs by visiting cooperative organizations are also included in the curriculum. In this paper, we report about the progress of the new educational program for nuclear engineering in Ibaraki University.

  13. Development and Performance Verification of Fiber Optic Temperature Sensors in High Temperature Engine Environments

    Science.gov (United States)

    Adamovsky, Grigory; Mackey, Jeffrey R.; Kren, Lawrence A.; Floyd, Bertram M.; Elam, Kristie A.; Martinez, Martel

    2014-01-01

    A High Temperature Fiber Optic Sensor (HTFOS) has been developed at NASA Glenn Research Center for aircraft engine applications. After fabrication and preliminary in-house performance evaluation, the HTFOS was tested in an engine environment at NASA Armstrong Flight Research Center. The engine tests enabled the performance of the HTFOS in real engine environments to be evaluated along with the ability of the sensor to respond to changes in the engine's operating condition. Data were collected prior, during, and after each test in order to observe the change in temperature from ambient to each of the various test point levels. An adequate amount of data was collected and analyzed to satisfy the research team that HTFOS operates properly while the engine was running. Temperature measurements made by HTFOS while the engine was running agreed with those anticipated.

  14. Continuing Professional Development (CPD) of the nuclear and radiation professional engineers

    International Nuclear Information System (INIS)

    Sasaki, Satoru

    2016-01-01

    Professional Engineer is the national qualification stipulated by the Professional Engineer Act. A Professional Engineer in this Act means a person who conducts business on matters of planning, research, design, analysis, testing, evaluation or guidance thereof, which requires application of extensive scientific and technical expertise, and has three obligation and two responsibility related to engineer ethic. A technical discipline for nuclear and radiation technology in 2004, was established for the purpose of upgrading the skills of engineers in nuclear technology fields, utilizing their ability in nuclear safety regulation fields, and further strengthening safety management system in each entity. The activity of the nuclear and radiation professional engineers for the past 10 years was evaluated. For the next ten years, awareness of the role of the professional engineer to talk with general public is needed, and it is important to continue professional development. (author)

  15. Automated Model Fit Method for Diesel Engine Control Development

    NARCIS (Netherlands)

    Seykens, X.; Willems, F.P.T.; Kuijpers, B.; Rietjens, C.

    2014-01-01

    This paper presents an automated fit for a control-oriented physics-based diesel engine combustion model. This method is based on the combination of a dedicated measurement procedure and structured approach to fit the required combustion model parameters. Only a data set is required that is

  16. GIS for Highway Engineering in Developing Countries | Mulaku ...

    African Journals Online (AJOL)

    A Geographic Information System (GIS) is a computer based information system that enables the input, management, analysis, output and dissemination of geospatial data and information. It is therefore an invaluable management tool in all fields where geospatial data is applied, such as highway engineering. Unfortunately ...

  17. PBL and CDIO: Complementary Models for Engineering Education Development

    Science.gov (United States)

    Edström, Kristina; Kolmos, Anette

    2014-01-01

    This paper compares two models for reforming engineering education, problem/project-based learning (PBL), and conceive-design-implement-operate (CDIO), identifying and explaining similarities and differences. PBL and CDIO are defined and contrasted in terms of their history, community, definitions, curriculum design, relation to disciplines,…

  18. Developing Air Force Systems Engineers - a Flight Path

    Science.gov (United States)

    2012-12-01

    to viewing problems from different perspectives. Specialists generally see the world through the lens of their own specialty. To paraphrase Abraham ... Maslow : If all you have is a hammer, everything looks like a nail. Systems engineers are supposed to take a different approach to problem solving

  19. Automated model fit method for diesel engine control development

    NARCIS (Netherlands)

    Seykens, X.L.J.; Willems, F.P.T.; Kuijpers, B.; Rietjens, C.J.H.

    2014-01-01

    This paper presents an automated fit for a control-oriented physics-based diesel engine combustion model. This method is based on the combination of a dedicated measurement procedure and structured approach to fit the required combustion model parameters. Only a data set is required that is

  20. Developing Design and Management Skills for Senior Industrial Engineering Students

    Science.gov (United States)

    Urbanic, R. J.

    2011-01-01

    In Canadian engineering institutions, a significant design experience must occur in the final year of study. In the Department of Industrial and Manufacturing Systems at the University of Windsor, unsolved, open ended projects sponsored by industrial partners from a variety of sectors are provided to the student teams in order for them to apply…