WorldWideScience

Sample records for arizona study qa analytical

  1. Integrating solar PV (photovoltaics) in utility system operations: Analytical framework and Arizona case study

    International Nuclear Information System (INIS)

    Wu, Jing; Botterud, Audun; Mills, Andrew; Zhou, Zhi; Hodge, Bri-Mathias; Heaney, Mike

    2015-01-01

    A systematic framework is proposed to estimate the impact on operating costs due to uncertainty and variability in renewable resources. The framework quantifies the integration costs associated with sub-hourly variability and uncertainty as well as day-ahead forecasting errors in solar PV (photovoltaics) power. A case study illustrates how changes in system operations may affect these costs for a utility in the southwestern United States (Arizona Public Service Company). We conduct an extensive sensitivity analysis under different assumptions about balancing reserves, system flexibility, fuel prices, and forecasting errors. We find that high solar PV penetrations may lead to operational challenges, particularly during low-load and high solar periods. Increased system flexibility is essential for minimizing integration costs and maintaining reliability. In a set of sensitivity cases where such flexibility is provided, in part, by flexible operations of nuclear power plants, the estimated integration costs vary between $1.0 and $4.4/MWh-PV for a PV penetration level of 17%. The integration costs are primarily due to higher needs for hour-ahead balancing reserves to address the increased sub-hourly variability and uncertainty in the PV resource. - Highlights: • We propose an analytical framework to estimate grid integration costs for solar PV. • Increased operating costs from variability and uncertainty in solar PV are computed. • A case study of a utility in Arizona is conducted. • Grid integration costs are found in the $1.0–4.4/MWh range for a 17% PV penetration. • Increased system flexibility is essential for minimizing grid integration costs

  2. Environmental analytical laboratory setup operation and QA/QC

    International Nuclear Information System (INIS)

    Hsu, J.P.; Boyd, J.A.; DeViney, S.

    1991-01-01

    Environmental analysis requires precise and timely measurements. The required precise measurement is ensured with quality control and timeliness through an efficient operation. The efficiency of the operation also ensures cost-competitiveness. Environmental analysis plays a very important role in the environmental protection program. Due to the possible litigation involvement, most environmental analyses follow stringent criteria, such as the U.S. EPA Contract Laboratory Program procedures with analytical results documented in an orderly manner. The documentation demonstrates that all quality control steps are followed and facilitates data evaluation to determine the quality and usefulness of the data. Furthermore, the tedious documents concerning sample checking, chain-of-custody, standard or surrogate preparation, daily refrigerator and oven temperature monitoring, analytical and extraction logbooks, standard operation procedures, etc., also are an important part of the laboratory documentation. Quality control for environmental analysis is becoming more stringent, required documentation is becoming more detailed and turnaround time is shorter. However, the business is becoming more cost-competitive and it appears that this trend will continue. In this paper, we discuss what should be done to deal this high quality, fast-paced and tedious environmental analysis process at a competitive cost. The success of environmental analysis is people. The knowledge and experience of the staff are the key to a successful environmental analysis program. In order to be successful in this new area, the ability to develop new methods is crucial. In addition, the laboratory information system, laboratory automation and quality assurance/quality control (QA/QC) are major factors for laboratory success. This paper concentrates on these areas

  3. Comparability between NQA-1 and the QA programs for analytical laboratories within the nuclear industry and EPA hazardous waste laboratories

    International Nuclear Information System (INIS)

    English, S.L.; Dahl, D.R.

    1989-01-01

    There is increasing cooperation between the Department of Energy (DOE), Department of Defense (DOD), and the Environmental Protection Agency (EPA) in the activities associated with monitoring and clean-up of hazardous wastes. Pacific Northwest Laboratory (PNL) examined the quality assurance/quality control programs that the EPA requires of the private sector when performing routine analyses of hazardous wastes to confirm how or if the requirements correspond with PNL's QA program based upon NQA-1. This paper presents the similarities and differences between NQA-1 and the QA program identified in ASTM-C1009-83, Establishing a QA Program for Analytical Chemistry Laboratories within the Nuclear Industry; EPA QAMS-005/80, Interim Guidelines and Specifications for Preparing Quality Assurance Project Plans, which is referenced in Statements of Work for CERCLA analytical activities; and Chapter 1 of SW-846, which is used in analyses of RCRA samples. The EPA QA programs for hazardous waste analyses are easily encompassed within an already established NQA-1 QA program. A few new terms are introduced and there is an increased emphasis upon the QC/verification, but there are many of the same basic concepts in all the programs

  4. KINERJA AKADEMIK PASCA SERTIFIKASI AUN-QA PADA PROGRAM STUDI DI INSTITUT PERTANIAN BOGOR

    Directory of Open Access Journals (Sweden)

    Adelyna Adelyna

    2016-05-01

    Full Text Available The aims of the research are to evaluate the academic performance progress of the six study programs of IPB after the certification of AUN-QA. The research was a case study in six study programs that had been certified by AUN-QA until December 2014. This research was conducted with the objectives of defining the relevant indicators of BSC IPB and AUN-QA criteria, analyzing the criteria values of AUN-QA after the AUN-QA certification, analyzing the academic performance based on KPI BSC after the AUN-QA certification, and analyzing the problems in improving academic performance as the basis for the formulation of strategies for improving academic quality. The method used in this research was the balanced scorecard approach (BSC. The results showed that the certification of AUN-QA contains 15 relevant criteria and supports the achievement of BSC IPB. Key performance indicators (KPI BSC IPB supported by the AUN-QA criteria consist of 21 of the 33 indicators of BSC IPB, and 14 of them are relegated to the BSC department indicators. The AUN-QA criteria values on the study program have increased with the highest criterion value in student quality and the lowest one in support staff quality. The weak criteria required to be improved include support staff quality, student assessment, stakeholder feedback, and program specification.Keywords: AUN-QA certification, academic performance, balanced scorecard

  5. A comparative study and analysis of QA requirements for the establishment of a nuclear R and D QA system

    International Nuclear Information System (INIS)

    Kim, Kwan Hyun

    2000-06-01

    This technical report provides recommendations on how to fulfill the requirements of the code in relation to QA activities for nuclear R and D field. This guide applies to the quality assurance (QA) programmes of the responsible organization, i.e. the organization having overall responsibility for the nuclear power plant, as well as to any other separate QA programmes in each stage of a nuclear R and D project. This guide covers QA work on items, services and processes impacting nuclear safety during siting, design, construction, commissioning, operation and decommissioning of nuclear power plants. The impact on safety may occur during the performance of the QA work, or owing to the application of the results of the QA. This guide may, with appropriate modification, also be usefully applied at nuclear installations other than nuclear R and D field

  6. SU-F-T-275: A Correlation Study On 3D Fluence-Based QA and 2D Dose Measurement-Based QA

    International Nuclear Information System (INIS)

    Liu, S; Mazur, T; Li, H; Green, O; Sun, B; Mutic, S; Yang, D

    2016-01-01

    Purpose: The aim of this paper was to demonstrate the feasibility and creditability of computing and verifying 3D fluencies to assure IMRT and VMAT treatment deliveries, by correlating the passing rates of the 3D fluence-based QA (P(ά)) to the passing rates of 2D dose measurementbased QA (P(Dm)). Methods: 3D volumetric primary fluencies are calculated by forward-projecting the beam apertures and modulated by beam MU values at all gantry angles. We first introduce simulated machine parameter errors (MU, MLC positions, jaw, gantry and collimator) to the plan. Using passing rates of voxel intensity differences (P(Ir)) and 3D gamma analysis (P(γ)), calculated 3D fluencies, calculated 3D delivered dose, and measured 2D planar dose in phantom from the original plan are then compared with those from corresponding plans with errors, respectively. The correlations of these three groups of resultant passing rates, i.e. 3D fluence-based QA (P(ά,Ir) and P(ά,γ)), calculated 3D dose (P(Dc,Ir) and P(Dc,γ)), and 2D dose measurement-based QA (P(Dm,Ir) and P(Dm,γ)), will be investigated. Results: 20 treatment plans with 5 different types of errors were tested. Spearman’s correlations were found between P(ά,Ir) and P(Dc,Ir), and also between P(ά,γ) and P(Dc,γ), with averaged p-value 0.037, 0.065, and averaged correlation coefficient ρ-value 0.942, 0.871 respectively. Using Matrixx QA for IMRT plans, Spearman’s correlations were also obtained between P(ά,Ir) and P(Dm,Ir) and also between P(ά,γ) and P(Dm,γ), with p-value being 0.048, 0.071 and ρ-value being 0.897, 0.779 respectively. Conclusion: The demonstrated correlations improve the creditability of using 3D fluence-based QA for assuring treatment deliveries for IMRT/VMAT plans. Together with advantages of high detection sensitivity and better visualization of machine parameter errors, this study further demonstrates the accuracy and feasibility of 3D fluence based-QA in pre-treatment QA and daily QA. Research

  7. Studies on a Q/A selector for the SECRAL electron cyclotron resonance ion source.

    Science.gov (United States)

    Yang, Y; Sun, L T; Feng, Y C; Fang, X; Lu, W; Zhang, W H; Cao, Y; Zhang, X Z; Zhao, H W

    2014-08-01

    Electron cyclotron resonance ion sources are widely used in heavy ion accelerators in the world because they are capable of producing high current beams of highly charged ions. However, the design of the Q/A selector system for these devices is challenging, because it must have a sufficient ion resolution while controlling the beam emittance growth. Moreover, this system has to be matched for a wide range of ion beam species with different intensities. In this paper, research on the Q/A selector system at the SECRAL (Superconducting Electron Cyclotron Resonance ion source with Advanced design in Lanzhou) platform both in experiment and simulation is presented. Based on this study, a new Q/A selector system has been designed for SECRAL II. The features of the new design including beam simulations are also presented.

  8. Interlaboratory analytical performance studies; a way to estimate measurement uncertainty

    Directory of Open Access Journals (Sweden)

    El¿bieta £ysiak-Pastuszak

    2004-09-01

    Full Text Available Comparability of data collected within collaborative programmes became the key challenge of analytical chemistry in the 1990s, including monitoring of the marine environment. To obtain relevant and reliable data, the analytical process has to proceed under a well-established Quality Assurance (QA system with external analytical proficiency tests as an inherent component. A programme called Quality Assurance in Marine Monitoring in Europe (QUASIMEME was established in 1993 and evolved over the years as the major provider of QA proficiency tests for nutrients, trace metals and chlorinated organic compounds in marine environment studies. The article presents an evaluation of results obtained in QUASIMEME Laboratory Performance Studies by the monitoring laboratory of the Institute of Meteorology and Water Management (Gdynia, Poland in exercises on nutrient determination in seawater. The measurement uncertainty estimated from routine internal quality control measurements and from results of analytical performance exercises is also presented in the paper.

  9. SU-F-T-287: A Preliminary Study On Patient Specific VMAT Verification Using a Phosphor-Screen Based Geometric QA System (Raven QA)

    International Nuclear Information System (INIS)

    Lee, M; Yi, B; Wong, J; Ding, K

    2016-01-01

    Purpose: The RavenQA system (LAP Laser, Germany) is a QA device with a phosphor screen detector for performing the QA tasks of TG-142. This study tested if it is feasible to use the system for the patient specific QA of the Volumetric Modulated Arc Therapy (VMAT). Methods: Water equivalent material (5cm) is attached to the front of the detector plate of the RavenQA for dosimetry purpose. Then the plate is attached to the gantry to synchronize the movement between the detector and the gantry. Since the detector moves together with gantry, The ’Reset gantry to 0’ function of the Eclipse planning system (Varian, CA) is used to simulate the measurement situation when calculating dose of the detector plate. The same gantry setup is used when delivering the treatment beam for feasibility test purposes. Cumulative dose is acquired for each arc. The optical scatter component of each captured image from the CCD camera is corrected by deconvolving the 2D spatial invariant optical scatter kernel (OSK). We assume that the OSK is a 2D isotropic point spread function with inverse-squared decrease as a function of radius from the center. Results: Three cases of VMAT plans including head & neck, whole pelvis and abdomen-pelvis are tested. Setup time for measurements was less than 5 minutes. Passing rates of absolute gamma were 99.3, 98.2, 95.9 respectively for 3%/3mm criteria and 96.2, 97.1, 86.4 for 2%/2mm criteria. The abdomen-pelvis field has long treatment fields, 37cm, which are longer than the detector plate (25cm). This plan showed relatively lower passing rate than other plans. Conclusion: An algorithm for IMRT/VMAT verification using the RavenQA has been developed and tested. The model of spatially invariant OSK works well for deconvolution purpose. It is proved that the RavenQA can be used for the patient specific verification of VMAT. This work is funded in part by a Maryland Industrial Partnership Program grant to University of Maryland and to JPLC who owns the

  10. Deep nets vs expert designed features in medical physics: An IMRT QA case study.

    Science.gov (United States)

    Interian, Yannet; Rideout, Vincent; Kearney, Vasant P; Gennatas, Efstathios; Morin, Olivier; Cheung, Joey; Solberg, Timothy; Valdes, Gilmer

    2018-03-30

    The purpose of this study was to compare the performance of Deep Neural Networks against a technique designed by domain experts in the prediction of gamma passing rates for Intensity Modulated Radiation Therapy Quality Assurance (IMRT QA). A total of 498 IMRT plans across all treatment sites were planned in Eclipse version 11 and delivered using a dynamic sliding window technique on Clinac iX or TrueBeam Linacs. Measurements were performed using a commercial 2D diode array, and passing rates for 3%/3 mm local dose/distance-to-agreement (DTA) were recorded. Separately, fluence maps calculated for each plan were used as inputs to a convolution neural network (CNN). The CNNs were trained to predict IMRT QA gamma passing rates using TensorFlow and Keras. A set of model architectures, inspired by the convolutional blocks of the VGG-16 ImageNet model, were constructed and implemented. Synthetic data, created by rotating and translating the fluence maps during training, was created to boost the performance of the CNNs. Dropout, batch normalization, and data augmentation were utilized to help train the model. The performance of the CNNs was compared to a generalized Poisson regression model, previously developed for this application, which used 78 expert designed features. Deep Neural Networks without domain knowledge achieved comparable performance to a baseline system designed by domain experts in the prediction of 3%/3 mm Local gamma passing rates. An ensemble of neural nets resulted in a mean absolute error (MAE) of 0.70 ± 0.05 and the domain expert model resulted in a 0.74 ± 0.06. Convolutional neural networks (CNNs) with transfer learning can predict IMRT QA passing rates by automatically designing features from the fluence maps without human expert supervision. Predictions from CNNs are comparable to a system carefully designed by physicist experts. © 2018 American Association of Physicists in Medicine.

  11. Achievements and advantages of participation in the IAEA project RER 002/004/1999-2001 'QA/QC of Nuclear Analytical Techniques'

    International Nuclear Information System (INIS)

    Vata, Ion; Cincu, Em.

    2002-01-01

    The National Institute for Physics and Engineering 'Horia Hulubei' (IFIN-HH) decided in the late 1990s to start applying nuclear techniques in economy and social life on a routine scale; reaching this goal implied achieving first-rate analytical performances and complying with the QA/QC requirements, as detailed in the ISO 17025. The IAEA Project appeared in 1999 as the best opportunity and tool for our specialists to become familiar with the standard requirements and begin to implement them in their operations, thus further enabling them to apply for accreditation according to the international criteria. This report outlines the experience gained from the participation in the project. The accomplishments of the project are presented and the main difficulties are identified

  12. QA programme documentation

    International Nuclear Information System (INIS)

    Scheibelt, L.

    1980-01-01

    The present paper deals with the following topics: The need for a documented Q.A. program; Establishing a Q.A. program; Q.A. activities; Fundamental policies; Q.A. policies; Quality objectives Q.A. manual. (orig./RW)

  13. Assessment of selected inorganic constituents in streams in the Central Arizona Basins Study Area, Arizona and northern Mexico, through 1998

    Science.gov (United States)

    Anning, David W.

    2003-01-01

    Stream properties and water-chemistry constituent concentrations from data collected by the National Water-Quality Assessment and other U.S. Geological Survey water-quality programs were analyzed to (1) assess water quality, (2) determine natural and human factors affecting water quality, and (3) compute stream loads for the surface-water resources in the Central Arizona Basins study area. Stream temperature, pH, dissolved-oxygen concentration and percent saturation, and dissolved-solids, suspended-sediment, and nutrient concentration data collected at 41 stream-water quality monitoring stations through water year 1998 were used in this assessment. Water-quality standards applicable to the stream properties and water-chemistry constituent concentration data for the stations investigated in this study generally were met, although there were some exceedences. In a few samples from the White River, the Black River, and the Salt River below Stewart Mountain Dam, the pH in reaches designated as a domestic drinking water source was higher than the State of Arizona standard. More than half of the samples from the Salt River below Stewart Mountain Dam and almost all of the samples from the stations on the Central Arizona Project Canal?two of the three most important surface-water sources used for drinking water in the Central Arizona Basins study area?exceeded the U.S. Environmental Protection Agency drinking water Secondary Maximum Contaminant Level for dissolved solids. Two reach-specific standards for nutrients established by the State of Arizona were exceeded many times: (1) the annual mean concentration of total phosphorus was exceeded during several years at stations on the main stems of the Salt and Verde Rivers, and (2) the annual mean concentration of total nitrogen was exceeded during several years at the Salt River near Roosevelt and at the Salt River below Stewart Mountain Dam. Stream properties and water-chemistry constituent concentrations were related to

  14. SU-E-T-636: ProteusONE Machine QA Procedure and Stabiity Study: Half Year Clinical Operation

    Energy Technology Data Exchange (ETDEWEB)

    Freund, D; Ding, X; Wu, H; Zhang, J; Syh, J; Syh, J; Patel, B; Song, X [Willis-Knighton Medical Center, Shreveport, LA (United States)

    2015-06-15

    Purpose: The objective of this study is to evaluate the stability of ProteusOne, the 1st commercial PBS proton system, throughout the daily QA and monthly over 6 month clinical operation. Method: Daily QA test includes IGRT position/repositioning, output in the middle of SOBP, beam flatness, symmetry, inplane and crossplane dimensions as well as energy range check. Daily range shifter QA consist of output, symmetry and field size checks to make sure its integrity. In 30 mins Daily QA test, all the measurements are performed using the MatriXXPT (IBA dosimetry). The data from these measurement was collected and compare over the first 6 month of clinical operation. In addition to the items check in daily QA, the summary also includes the monthly QA gantry star shots, absolute position check using a novel device, XRV-100. Results: Average machine output at the center of the spread out bragg peak was 197.5±.8 cGy and was within 1%of the baseline at 198.4 cGy. Beam flatness was within 1% cross plane with an average of 0.67±0.12% and 2% in-plane with an average of 1.08±0.17% compared to baseline measurements of 0.6 and 1.03, respectively. In all cases the radiation isocenter shift was less than or equal to 1mm. Output for the range shifter was within 2% for each individual measurement and averaged 34.4±.2cGy compare to a baseline reading of 34.5cGy. The average range shifter in and cross plane field size measurements were 19.8±0.5cm and 20.5±0.4cm compared with baseline values of 20.19cm and 20.79cm, respectively. Range shifter field symmetry had an average of less 1% for both in-plane and cross plane measurements. Conclusion: All machine metrics over the past 6 months have proved to be stable. Although, some averages are outside the baseline measurement they are within 1% tolerance and the deviation across all measurements is minimal.

  15. SU-E-T-636: ProteusONE Machine QA Procedure and Stabiity Study: Half Year Clinical Operation

    International Nuclear Information System (INIS)

    Freund, D; Ding, X; Wu, H; Zhang, J; Syh, J; Syh, J; Patel, B; Song, X

    2015-01-01

    Purpose: The objective of this study is to evaluate the stability of ProteusOne, the 1st commercial PBS proton system, throughout the daily QA and monthly over 6 month clinical operation. Method: Daily QA test includes IGRT position/repositioning, output in the middle of SOBP, beam flatness, symmetry, inplane and crossplane dimensions as well as energy range check. Daily range shifter QA consist of output, symmetry and field size checks to make sure its integrity. In 30 mins Daily QA test, all the measurements are performed using the MatriXXPT (IBA dosimetry). The data from these measurement was collected and compare over the first 6 month of clinical operation. In addition to the items check in daily QA, the summary also includes the monthly QA gantry star shots, absolute position check using a novel device, XRV-100. Results: Average machine output at the center of the spread out bragg peak was 197.5±.8 cGy and was within 1%of the baseline at 198.4 cGy. Beam flatness was within 1% cross plane with an average of 0.67±0.12% and 2% in-plane with an average of 1.08±0.17% compared to baseline measurements of 0.6 and 1.03, respectively. In all cases the radiation isocenter shift was less than or equal to 1mm. Output for the range shifter was within 2% for each individual measurement and averaged 34.4±.2cGy compare to a baseline reading of 34.5cGy. The average range shifter in and cross plane field size measurements were 19.8±0.5cm and 20.5±0.4cm compared with baseline values of 20.19cm and 20.79cm, respectively. Range shifter field symmetry had an average of less 1% for both in-plane and cross plane measurements. Conclusion: All machine metrics over the past 6 months have proved to be stable. Although, some averages are outside the baseline measurement they are within 1% tolerance and the deviation across all measurements is minimal

  16. NRC overview: Repository QA

    International Nuclear Information System (INIS)

    Kennedy, J.E.

    1988-01-01

    The US Department of Energy (DOE) is on the threshold of an extensive program for characterizing Yucca Mountain in Nevada to determine if it is a suitable site for the permanent disposal of high-level nuclear waste. Earlier this year, the DOE published the Consultation Draft Site Characterization Plan for the Nevada site, which describes in some detail the studies that need to be performed to determine if the site is acceptable. In the near future, the final site characterization plan (SCP) is expected to be issued and large-scale site characterization activities to begin. The data and analyses that will result from the execution of that plan are expected to be the primary basis for the license application to the US Nuclear Regulatory Commission (NRC). Because of the importance of these data and analyses in the assessment of the suitability of the site and in the demonstration of that suitability in the NRC licensing process, the NRC requires in 10CFR60 that site characterization be performed under a quality assurance (QA) program. The QA program is designed to provide confidence that data are valid, retrievable, and reproducible. The documentation produced by the program will form an important part of the record on which the suitability of the site is judged in licensing. In addition, because the NRC staff can review only a selected portion of the data collected, the staff will need to rely on the system of controls in the DOE QA program

  17. How users adopt healthcare information: An empirical study of an online Q&A community.

    Science.gov (United States)

    Jin, Jiahua; Yan, Xiangbin; Li, Yijun; Li, Yumei

    2016-02-01

    The emergence of social media technology has led to the creation of many online healthcare communities, where patients can easily share and look for healthcare-related information from peers who have experienced a similar problem. However, with increased user-generated content, there is a need to constantly analyse which content should be trusted as one sifts through enormous amounts of healthcare information. This study aims to explore patients' healthcare information seeking behavior in online communities. Based on dual-process theory and the knowledge adoption model, we proposed a healthcare information adoption model for online communities. This model highlights that information quality, emotional support, and source credibility are antecedent variables of adoption likelihood of healthcare information, and competition among repliers and involvement of recipients moderate the relationship between the antecedent variables and adoption likelihood. Empirical data were collected from the healthcare module of China's biggest Q&A community-Baidu Knows. Text mining techniques were adopted to calculate the information quality and emotional support contained in each reply text. A binary logistics regression model and hierarchical regression approach were employed to test the proposed conceptual model. Information quality, emotional support, and source credibility have significant and positive impact on healthcare information adoption likelihood, and among these factors, information quality has the biggest impact on a patient's adoption decision. In addition, competition among repliers and involvement of recipients were tested as moderating effects between these antecedent factors and the adoption likelihood. Results indicate competition among repliers positively moderates the relationship between source credibility and adoption likelihood, and recipients' involvement positively moderates the relationship between information quality, source credibility, and adoption

  18. Patient QA systems for rotational radiation therapy

    DEFF Research Database (Denmark)

    Fredh, Anna; Scherman, J.B.; Munck af Rosenschöld, Per Martin

    2013-01-01

    The purpose of the present study was to investigate the ability of commercial patient quality assurance (QA) systems to detect linear accelerator-related errors.......The purpose of the present study was to investigate the ability of commercial patient quality assurance (QA) systems to detect linear accelerator-related errors....

  19. The Migrant Border Crossing Study: A methodological overview of research along the Sonora-Arizona border.

    Science.gov (United States)

    Martínez, Daniel E; Slack, Jeremy; Beyerlein, Kraig; Vandervoet, Prescott; Klingman, Kristin; Molina, Paola; Manning, Shiras; Burham, Melissa; Walzak, Kylie; Valencia, Kristen; Gamboa, Lorenzo

    2017-07-01

    Increased border enforcement efforts have redistributed unauthorized Mexican migration to the United States (US) away from traditional points of crossing, such as San Diego and El Paso, and into more remote areas along the US-Mexico border, including southern Arizona. Yet relatively little quantitative scholarly work exists examining Mexican migrants' crossing, apprehension, and repatriation experiences in southern Arizona. We contend that if scholars truly want to understand the experiences of unauthorized migrants in transit, such migrants should be interviewed either at the border after being removed from the US, or during their trajectories across the border, or both. This paper provides a methodological overview of the Migrant Border Crossing Study (MBCS), a unique data source on Mexican migrants who attempted an unauthorized crossing along the Sonora-Arizona border, were apprehended, and repatriated to Nogales, Sonora in 2007-09. We also discuss substantive and theoretical contributions of the MBCS.

  20. A Study of Post-Graduate Plans of Arizona High School Seniors. Final Report.

    Science.gov (United States)

    Fenske, Robert H.; And Others

    A study undertaken in Arizona in 1975 was comprised of two parts, a pilot study and a comprehensive survey of high school students. It had as an overall objective to provide a data resource useful to all citizens and postsecondary institutions, to manpower and employment agencies, and to the state's high schools for program planning and…

  1. The quality assurance process for the ARTSCAN head and neck study - A practical interactive approach for QA in 3DCRT and IMRT

    International Nuclear Information System (INIS)

    Johansson, Karl-Axel; Nilsson, Per; Zackrisson, Bjoern; Ohlson, Birgitta; Kjellen, Elisabeth; Mercke, Claes; Alvarez-Fonseca, Mauricio; Billstroem, Anette; Bjoerk-Eriksson, Thomas; Bjoer, Ove; Ekberg, Lars; Friesland, Signe; Karlsson, Magnus; Lagerlund, Magnus; Lundkvist, Lena; Loefroth, Per-Olov; Loefvander-Thapper, Kerstin; Nilsson, Alla; Nyman, Jan; Persson, Essie

    2008-01-01

    Aim: This paper describes the quality assurance (QA) work performed in the Swedish multicenter ARTSCAN (Accelerated RadioTherapy of Squamous cell CArcinomas in the head and Neck) trial to guarantee high quality in a multicenter study which involved modern radiotherapy such as 3DCRT or IMRT. Materials and methods: The study was closed in June 2006 with 750 randomised patients. Radiation therapy-related data for every patient were sent by each participating centre to the QA office where all trial data were reviewed, analysed and stored. In case of any deviation from the protocol, an interactive process was started between the QA office and the local responsible clinician and/or physicist to increase the compliance to the protocol for future randomised patients. Meetings and workshops were held on a regular basis for discussions on various trial-related issues and for the QA office to report on updated results. Results and discussion: This review covers the 734 patients out of a total of 750 who had entered the study. Deviations early in the study were corrected so that the overall compliance to the protocol was very high. There were only negligible variations in doses and dose distributions to target volumes for each specific site and stage. The quality of the treatments was high. Furthermore, an extensive database of treatment parameters was accumulated for future dose-volume vs. endpoint evaluations. Conclusions: This comprehensive QA programme increased the probability to draw firm conclusions from our study and may serve as a concept for QA work in future radiotherapy trials where comparatively small effects are searched for in a heterogeneous tumour population

  2. Risk Assessment Stability: A Revalidation Study of the Arizona Risk/Needs Assessment Instrument

    Science.gov (United States)

    Schwalbe, Craig S.

    2009-01-01

    The actuarial method is the gold standard for risk assessment in child welfare, juvenile justice, and criminal justice. It produces risk classifications that are highly predictive and that may be robust to sampling error. This article reports a revalidation study of the Arizona Risk/Needs Assessment instrument, an actuarial instrument for juvenile…

  3. LED Street Lighting Solutions: Flagstaff, Arizona as a Case Study

    Science.gov (United States)

    Hall, Jeffrey C.

    2018-01-01

    Dark-sky protection in Flagstaff, Arizona extends back to 1958, with the first ordinance in the City banning advertising floodlights. The current ordinance, adopted in 1989, is comprehensive and has played a critical role in maintaining the quality of the night sky for astronomy, tourism, public enjoyment, and other purposes. Flagstaff, like many communities around the world, is now working on a transition from legacy bulb-based technology to LED for its outdoor lighting. The City, Lowell Observatory, the U. S. Naval Observatory, and the Flagstaff Dark Skies Coalition have been working intensively for two years to identify an LED-based street lighting solution that will preserve the City's dark skies while meeting municipal needs. We will soon be installing test fixtures for an innovative solution incorporating narrow-band amber LED and modest amounts of low-CCT white LED. In this talk, I will review the types of LEDs available for outdoor lighting and discuss the plans for Flagstaff's street lighting in the LED era, which we hope will be a model for communities worldwide.

  4. A feasibility study for Arizona's roadway safety management process using the Highway Safety Manual and SafetyAnalyst : final report.

    Science.gov (United States)

    2016-07-01

    To enable implementation of the American Association of State Highway Transportation (AASHTO) Highway Safety Manual using : SaftetyAnalyst (an AASHTOWare software product), the Arizona Department of Transportation (ADOT) studied the data assessment :...

  5. A user need study and system plan for an Arizona Natural Resources Information System report to the Arizona state legislature

    Science.gov (United States)

    1980-01-01

    A survey instrument was developed and implemented in order to evaluate the current needs for natural resource information in Arizona and to determine which state agencies have information systems capable of coordinating, accessing and analyzing the data. Data and format requirements were determined for the following categories: air quality, animals, cultural resources, geology, land use, soils, water, vegetation, ownership, and social and economic aspects. Hardware and software capabilities were assessed and a data processing plan was developed. Possible future applications with the next generation LANDSAT were also identified.

  6. Seamless Digital Environment – Data Analytics Use Case Study

    Energy Technology Data Exchange (ETDEWEB)

    Oxstrand, Johanna [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2017-08-01

    Multiple research efforts in the U.S Department of Energy Light Water Reactor Sustainability (LWRS) Program studies the need and design of an underlying architecture to support the increased amount and use of data in the nuclear power plant. More specifically the three LWRS research efforts; Digital Architecture for an Automated Plant, Automated Work Packages, Computer-Based Procedures for Field Workers, and the Online Monitoring efforts all have identified the need for a digital architecture and more importantly the need for a Seamless Digital Environment (SDE). A SDE provides a mean to access multiple applications, gather the data points needed, conduct the analysis requested, and present the result to the user with minimal or no effort by the user. During the 2016 annual Nuclear Information Technology Strategic Leadership (NITSL) group meeting the nuclear utilities identified the need for research focused on data analytics. The effort was to develop and evaluate use cases for data mining and analytics for employing information from plant sensors and database for use in developing improved business analytics. The goal of the study is to research potential approaches to building an analytics solution for equipment reliability, on a small scale, focusing on either a single piece of equipment or a single system. The analytics solution will likely consist of a data integration layer, predictive and machine learning layer and the user interface layer that will display the output of the analysis in a straight forward, easy to consume manner. This report describes the use case study initiated by NITSL and conducted in a collaboration between Idaho National Laboratory, Arizona Public Service – Palo Verde Nuclear Generating Station, and NextAxiom Inc.

  7. Analytical Study of Oxalates Coprecipitation

    Directory of Open Access Journals (Sweden)

    Liana MARTA

    2003-03-01

    Full Text Available The paper deals with the establishing of the oxalates coprecipitation conditions in view of the synthesis of superconducting systems. A systematic analytical study of the oxalates precipitation conditions has been performed, for obtaining superconducting materials, in the Bi Sr-Ca-Cu-O system. For this purpose, the formulae of the precipitates solubility as a function of pH and oxalate excess were established. The possible formation of hydroxo-complexes and soluble oxalato-complexes was taken into account. A BASIC program was used for tracing the precipitation curves. The curves of the solubility versus pH for different oxalate excess have plotted for the four oxalates, using a logaritmic scale. The optimal conditions for the quantitative oxalate coprecipitation have been deduced from the diagrams. The theoretical curves were confirmed by experimental results. From the precursors obtained by this method, the BSCCO superconducting phases were obtained by an appropriate thermal treatment. The formation of the superconducting phases was identified by X-ray diffraction analysis.

  8. Analytic study of resistive instabilities

    Energy Technology Data Exchange (ETDEWEB)

    Svensson, Magnus

    2003-05-01

    In a fusion plasma there is always a small amount of resistivity that may cause instabilities. Although their rather slow growth rates they can be of major importance for fusion plasma confinement. In this work a MAPLE-code was rewritten and simplified to make it possible to analytically solve the linearized MHD-equations with resistivity in an RFP-configuration. By using the MHD-equations and expanding the unknown perturbed quantities u{sub 1r}(r) and B{sub 1r}(r) as Taylor series and solving each coefficient we could get eigenvalues, dispersion relations and a relation between the growth rate and the resistivity. The new code was first used to solve two cases with no resistivity and simple unstable equilibria which after running gave the correct expected results. The difference from running the original code with these two cases was the greater speed of the calculations and the less memory needed. Then by using an ideal MHD-stable equilibrium in a plasma with no resistivity the code gave us solutions which unfortunately were not of the expected kind but the time of the calculations was still very fast. The resistivity was finally added to the code with the ideal MHD-stable equilibrium. The program also this time gave incorrect results. We could, however, see from a relation between the growth rate and the resistivity that the solution may be approximately correct in this domain. Although we did not get all the correct results we have to consider the fact that we got results, that were not possible before. Before this work was carried out we could not get any results at all in the resistive cue because of the very long memory demanding expressions. In future work and studies it is not only possible to get the desired eigenvalues {gamma} as function of {eta} but also possible to get expressions for eigenfunctions, dispersion relations and other significant relations with a number of variable parameters. We could also use the method for any geometry and possibly for

  9. Analytic study of resistive instabilities

    International Nuclear Information System (INIS)

    Svensson, Magnus

    2003-05-01

    In a fusion plasma there is always a small amount of resistivity that may cause instabilities. Although their rather slow growth rates they can be of major importance for fusion plasma confinement. In this work a MAPLE-code was rewritten and simplified to make it possible to analytically solve the linearized MHD-equations with resistivity in an RFP-configuration. By using the MHD-equations and expanding the unknown perturbed quantities u 1r (r) and B 1r (r) as Taylor series and solving each coefficient we could get eigenvalues, dispersion relations and a relation between the growth rate and the resistivity. The new code was first used to solve two cases with no resistivity and simple unstable equilibria which after running gave the correct expected results. The difference from running the original code with these two cases was the greater speed of the calculations and the less memory needed. Then by using an ideal MHD-stable equilibrium in a plasma with no resistivity the code gave us solutions which unfortunately were not of the expected kind but the time of the calculations was still very fast. The resistivity was finally added to the code with the ideal MHD-stable equilibrium. The program also this time gave incorrect results. We could, however, see from a relation between the growth rate and the resistivity that the solution may be approximately correct in this domain. Although we did not get all the correct results we have to consider the fact that we got results, that were not possible before. Before this work was carried out we could not get any results at all in the resistive cue because of the very long memory demanding expressions. In future work and studies it is not only possible to get the desired eigenvalues γ as function of η but also possible to get expressions for eigenfunctions, dispersion relations and other significant relations with a number of variable parameters. We could also use the method for any geometry and possibly for non

  10. Summary report of the TC regional project on 'QA/QC of nuclear analytical techniques' RER-2-004 (1999-2001)

    International Nuclear Information System (INIS)

    Akgun, A. Fadil

    2002-01-01

    This report provides a summary of the Cekmece Nuclear Research and Training Centre participation in the Project. The Project helped in setting up quality assurance system in the Centre and resulted in a progress in analytical proficiency as shown in the proficiency test results. The main accomplishments are listed along with the tasks to be done

  11. Energy-Water Microgrid Case Study at the University of Arizona's BioSphere 2

    Science.gov (United States)

    Daw, J.; Macknick, J.; Kandt, A.; Giraldez, J.

    2016-12-01

    Microgrids can provide reliable and cost-effective energy services in a variety of conditions and locations. To date, there has been minimal effort invested in developing energy-water microgrids that demonstrate the feasibility and leverage the synergies associated with designing and operating renewable energy and water systems in a coordinated framework. Water and wastewater treatment equipment can be operated in ways to provide ancillary services to the electrical grid and renewable energy can be utilized to power water-related infrastructure, but the potential for co-managed systems has not yet been quantified or fully characterized. Co-management and optimization of energy and water resources could lead to improved reliability and economic operating conditions. Energy-water microgrids could be a promising solution to improve energy and water resource management for islands, rural communities, distributed generation, Defense operations, and many parts of the world lacking critical infrastructure.The National Renewable Energy Laboratory (NREL) and the University of Arizona have been jointly researching energy-water microgrid opportunities through an effort at the university's BioSphere 2 (B2) Earth systems science research facility. B2 is an ideal case study for an energy-water microgrid test site, given its size, its unique mission and operations, the existence and criticality of water and energy infrastructure, and its ability to operate connected-to or disconnected-from the local electrical grid. Moreover, the B2 is a premier facility for undertaking agricultural research, providing an excellent opportunity to evaluate connections and tradeoffs in the food-energy-water nexus. The research effort at B2 identified the technical potential and associated benefits of an energy-water microgrid through the evaluation of energy ancillary services and peak load reductions and quantified the potential for B2 water-related loads to be utilized and modified to provide

  12. Heavy thinning of ponderosa pine stands: An Arizona case study

    Science.gov (United States)

    Peter F. Ffolliott; Jr. Baker; Gerald J. Gottfried

    2000-01-01

    Growth and structural changes in a mosaic of even-aged ponderosa pine (Pinus ponderosa) stands were studied for 25 years to determine the long-term impacts of a heavy thinning treatment to a basal-area level of 25 ft2/acre. Basal area and volume growth of these stands has increased since thinning and likely will continue to...

  13. Nuclear Hybrid Energy Systems Regional Studies: West Texas & Northeastern Arizona

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, Humberto E. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Chen, Jun [Idaho National Lab. (INL), Idaho Falls, ID (United States); Kim, Jong Suk [Idaho National Lab. (INL), Idaho Falls, ID (United States); McKellar, Michael George [Idaho National Lab. (INL), Idaho Falls, ID (United States); Deason, Wesley R [Idaho National Lab. (INL), Idaho Falls, ID (United States); Vilim, Richard B. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Bragg-Sitton, Shannon M. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Boardman, Richard D. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-04-01

    The primary objective of this study is to conduct a preliminary dynamic analysis of two realistic hybrid energy systems (HES) including a nuclear reactor as the main baseload heat generator (denoted as nuclear HES or nuclear hybrid energy systems [[NHES]) and to assess the local (e.g., HES owners) and system (e.g., the electric grid) benefits attainable by the application of NHES in scenarios with multiple commodity production and high penetration of renewable energy. It is performed for regional cases not generic examples based on available resources, existing infrastructure, and markets within the selected regions. This study also briefly addresses the computational capabilities developed to conduct such analyses, reviews technical gaps, and suggests some research paths forward.

  14. a cross-sectional analytic study 2014

    African Journals Online (AJOL)

    Assessment of HIV/AIDS comprehensive correct knowledge among Sudanese university: a cross-sectional analytic study 2014. ... There are limited studies on this topic in Sudan. In this study we investigated the Comprehensive correct ...

  15. Three-dimensional dose distribution in contrast-enhanced digital mammography using Gafchromic XR-QA2 films: Feasibility study

    International Nuclear Information System (INIS)

    Hwang, Yi-Shuan; Lin, Yu-Ying; Cheung, Yun-Chung; Tsai, Hui-Yu

    2014-01-01

    This study was aimed to establish three-dimensional dose distributions for contrast-enhanced digital mammography (CEDM) using self-developed Gafchromic XR-QA2 films. Dose calibration and distribution evaluations were performed on a full-field digital mammography unit with dual energy (DE) contrast-enhanced option. Strategy for dose calibration of films in the DE mode was based on the data obtained from common target/filter/kVp combinations used clinically and the dose response model modified from Rampado's model. Dose derived from films were also verified by measured data from an ionization chamber. The average difference of dose was 8.9% in the dose range for clinical uses. Three-dimensional dose distributions were estimated using triangular acrylic phantom equipped with the mammography system. Five pieces of film sheets were separately placed between the acrylic slabs to evaluate the dose distribution at different depths. After normalizing the dose in each pixel to the maximum dose at the top-center position of the acrylic, normalized dose distribution for transverse, coronal and sagittal planes, could thus be obtained. The depth dose distribution evaluated in this study may further serve as a reference for evaluating the patient glandular dose at different depths based on the entrance exposure information. - Highlights: • CEDM techniques can enhance contrast uptake areas and suppress background tissue. • Dose for the dual-energy acquisition is about 20% higher than standard mode. • A new method is proposed to estimate the 3D dose distribution in dual-energy CEDM. • Depth of normalized dose ratio of 0.5 is less than but near 1 cm in the DE mode

  16. Emotional Testimonies:An Ethnographic Study of Emotional Suffering Related to Migration from Mexico to Arizona

    Directory of Open Access Journals (Sweden)

    Rebecca eCrocker

    2015-07-01

    Full Text Available It is increasingly argued that social and economic inequity poorly affect overall health. One of the means through which these inequities are translated to the body is via negative emotions, which carry known psychological and physiological responses. This paper examines migration-related psychosocial stressors impacting first generation Mexican immigrants in southern Arizona, and reports on the primary emotional experiences immigrants associate with these stressors. Data were drawn from a qualitative, ethnographic study conducted over the course of 14 months during 2013-2014 with first generation Mexican immigrants (N=40 residing in Tucson Arizona and service providers working directly in the immigrant community (N=32. Results indicate that the primary structural vulnerabilities that cause emotional hardship amongst immigrants are pre-migration stressors and adversity, dangerous border crossings, detention and deportation, undocumented citizenship status, family separation, and extreme poverty. Many of these factors have intensified over the past decade due to increased border security and state level anti-immigrant legislation in Arizona. Immigrants connected these hardships to the emotions of trauma (50%, fear (65%, depression (75%, loneliness (75%, sadness (80%, and stress (85%, and most respondents reported suffering from three or more of these emotions. Given the heavy emotional toll of migration and the direct impact that regional legislation and border security had on well-being, this paper argues that emotion be considered an important mechanism for health declines in the immigrant community. In order to stem the frequency and intensity of emotional stress in the Mexican immigrant community in Tucson, it is imperative to support organizations and policies that promote community building and support networks and also expand access to and availability of mental health services for immigrants regardless of documentation status.

  17. Emotional Testimonies: An Ethnographic Study of Emotional Suffering Related to Migration from Mexico to Arizona

    Science.gov (United States)

    Crocker, Rebecca

    2015-01-01

    It is increasingly argued that social and economic inequities poorly affect overall health. One of the means through which these inequities are translated to the body is via negative emotions, which carry known psychological and physiological responses. This paper examines migration-related psychosocial stressors impacting first-generation Mexican immigrants in southern Arizona, and reports on the primary emotional experiences immigrants associate with these stressors. Data were drawn from a qualitative, ethnographic study conducted over the course of 14 months during 2013–2014 with first-generation Mexican immigrants (N = 40) residing in Tucson Arizona and service providers working directly in the immigrant community (N = 32). Results indicate that the primary structural vulnerabilities that cause emotional hardship among immigrants are pre-migration stressors and adversity, dangerous border crossings, detention and deportation, undocumented citizenship status, family separation, and extreme poverty. Many of these factors have intensified over the past decade due to increased border security and state level anti-immigrant legislation in Arizona. Immigrants connected these hardships to the emotions of trauma (50%), fear (65%), depression (75%), loneliness (75%), sadness (80%), and stress (85%), and most respondents reported suffering from three or more of these emotions. Given the heavy emotional toll of migration and the direct impact that regional legislation and border security had on well-being, this paper argues that emotion be considered an important mechanism for health declines in the immigrant community. In order to stem the frequency and intensity of emotional stress in the Mexican immigrant community in Tucson, it is imperative to support organizations and policies that promote community building and support networks and also expand access to and availability of mental health services for immigrants regardless of documentation status. PMID

  18. Quality control and quality assurance of nuclear analytical techniques. Thematic planning of QC/QA in technical co-operations. Report of the external participants

    International Nuclear Information System (INIS)

    Innes, R.W.; Bode, P.; Brickenkamp, C.S.; Casa, A.; Abdul Khalik Haji Wood

    1998-02-01

    In areas of trade, health, safety, and environmental protection users of a laboratory's analytical results, for example by governments and private institutions, are increasingly requiring demonstrable proof of the reliability and credibility of the laboratory's analytical results using internationally accepted standards. This is so that the products and the decisions based on these laboratory results will be accepted in the respective national and international communities. These requirements are being imposed, for example by the European Community and others, for products to be imported and can be a significant barrier to trade, especially for developing nations. In addition to this there is a growing need for these laboratories to operate efficiently and effectively to reduce internal waste, to provide reports on time in an economical manner and to become self supporting. The need for change is global and this proposal is for the Agency to pursue a thematic plan for the implementation of quality assurance as partners in development with the selected laboratories using nuclear analytical techniques. This report describes a model project for this thematic approach to confirm the models immediate benefits as well as facilitating long-term sustainability of member states' laboratories. The model is thematic in that it is also applicable to all other projects for which the credibility and reliability of the results of a laboratory's processes and results must be demonstrated. This model project provides a cost effective approach for protecting the Agency's investment in these laboratories and strengthening the ability of these national institutions to define, organize, and manage the application of nuclear technology in their respective countries. This pilot project consists of (1) determining the general levels of knowledge and application of quality assurance principles (as delineated in ISO Guide 25) in the responding laboratories; (2) selecting a trail group of

  19. Arizona transportation history.

    Science.gov (United States)

    2011-12-01

    The Arizona transportation history project was conceived in anticipation of Arizonas centennial, which will be : celebrated in 2012. Following approval of the Arizona Centennial Plan in 2007, the Arizona Department of : Transportation (ADOT) recog...

  20. The study of international and interstate transport of ozone in Yuma, Arizona

    Science.gov (United States)

    Li, Y.; Sonenberg, M.; Wood, J. L.; Pearson, C. R.; Colson, H.; Malloy, J. W.; Pace, M.; Mao, F.; Paul, J.; Busby, B. R.; Parkey, B.; Drago, L.; Franquist, T. S.

    2017-12-01

    In October 2015, EPA reduced the National Ambient Air Quality Standards (NAAQS) for ozone from 75 parts per billion (ppb) to 70 ppb. Meeting the new standard may be extremely challenging for some areas, including rural Yuma County in the State of Arizona. Yuma County faces unique air quality challenges, since it borders the Mexican states of Baja California and Sonora, and the State of California. The present study investigates the contribution of international and interstate transport of ozone and ozone precursors to episodes of elevated ozone concentrations in Yuma. The Arizona Department of Environmental Quality (ADEQ) merged HYSPLIT modeling outputs with two years of hourly ground ozone monitor data to investigate the potential area contributions to ozone concentrations in Yuma County. This analysis found that elevated ozone concentrations in Yuma in 2014 and 2015 frequently coincided with back-trajectories over both California and Mexico, typically favoring Mexico during the spring. In May 2017, ADEQ installed a new ozone monitor in San Luis Rio Colorado, Sonora, Mexico (Latitude: 32.4665, Longitude: -114.7688), which is 29 km south of ozone site in Yuma County. We will present the first simultaneous observations of ozone seasons in Sonora, Mexico, eastern California, and Yuma.

  1. A New Method to Study Analytic Inequalities

    Directory of Open Access Journals (Sweden)

    Xiao-Ming Zhang

    2010-01-01

    Full Text Available We present a new method to study analytic inequalities involving n variables. Regarding its applications, we proved some well-known inequalities and improved Carleman's inequality.

  2. QA at Fermilab

    Energy Technology Data Exchange (ETDEWEB)

    Bodnarczuk, M.

    1988-01-01

    This paper opens with a brief overview of the purpose of Fermilab and historical synopsis of the development and current status of quality assurance (QA) at the Laboratory. The paper subsequently addresses some of the more important aspects of interpreting the national standard ANSI/ASME NQA-1 in pure research environments like Fermilab. Highlights of this discussion include, (1) what is hermeneutics and why are hermeneutical considerations relevant for QA, (2) a critical analysis of NQA-1 focussing on teleological aspects of the standard, (3) a description of the hermeneutical approach to NQA-1 used at Fermilab which attempts to capture the true intents of the document without violating the deeply ingrained traditions of quality standards and peer review that have been foundational to the overall success of the paradigms of high-energy physics.

  3. School Finance in Arizona: A State-Local Partnership. A Special Study.

    Science.gov (United States)

    National Education Association, Washington, DC. Commission on Professional Rights and Responsibilities.

    This report discusses the dispute in Arizona over the 1967 legislation regulating educational finance and offers alternatives to that legislation. The document describes factors and issues relevant to an understanding of the present dispute, defines accepted principles of educational finance, provides factual information about Arizona's support of…

  4. Critical Race Theory Counterstory as Allegory: A Rhetorical Trope to Raise Awareness about Arizona's Ban on Ethnic Studies

    Science.gov (United States)

    Martinez, Aja Y.

    2013-01-01

    he critical race counterstory in this essay takes on the form of allegory to raise awareness about Arizona's anti-immigrant/Mexican climate, and pays particular attention to legislation targeted at Tucson Unified School District's Mexican American studies (also RAZA studies) program.

  5. Arizona Conserve Water Educators Guide

    Science.gov (United States)

    Project WET Foundation, 2007

    2007-01-01

    This award-winning, 350-page, full-color book provides a thorough study of Arizona water resources from a water conservation perspective. Its background section contains maps, graphs, diagrams and photos that facilitate the teaching of 15 interactive, multi-disciplinary lessons to K-12 students. In addition, 10 Arizona case studies are highlighted…

  6. Rural electrification in multiethnic Arizona: A study of power, urbanization and change

    Science.gov (United States)

    Glaser, Leah Suzanne

    2002-01-01

    From as early as the 1880s until as late as the 1970s, electrical power served as a critical tool for bringing America's diverse western communities into an urban industrial era. This study examines the process of electrification in three demographically diverse rural regions of Eastern Arizona. These three regions include the valleys of the Southeast, the White Mountains, and the Navajo Reservation to the north. While federal programs aided rural residents, local and regional factors determined the timing and nature of electrification and its impact. Access to electricity depended upon economics and technological advances, as well as a combination of local community and regional characteristics such as location, landscape, demographics, politics, and culture. At the turn of the century, electricity, with its elaborate and extensive infrastructure of wires, towers, and poles, emerged across America's cultural landscapes as the industrial era's most prominent symbol of progress, power, and a modern, urban lifestyle. Technological innovations and mechanization flourished, but primarily in the urban areas of the Northeast. People living outside concentrated settlements, of all ethnic backgrounds, had few hopes for delivery due to the cost of building power lines to a limited market. Arizona's rural population has historically been ethnically diverse, and its landscape varies from desert valleys to mountains of alpine forest. The federal government owns much of the land. Aided by federal guidance and funding sources like the New Deal's Rural Electrification Administration (REA), the existing rural communities took the initiative and constructed electrical systems specific to their local and regional needs. While products of the communities that built them, these systems symbolized and defined newly urbanized regions within the context of old rural landscapes, lifestyles, and traditions. In some ways the rural electrification process urbanized rural Arizona. The

  7. AN ANALYTICAL STUDY OF SWITCHING TRACTION MOTORS

    Directory of Open Access Journals (Sweden)

    V. M. Bezruchenko

    2010-03-01

    Full Text Available The analytical study of switching of the tractive engines of electric locomotives is conducted. It is found that the obtained curves of change of current of the sections commuted correspond to the theory of average rectilinear switching. By means of the proposed method it is possible on the stage of design of tractive engines to forecast the quality of switching and to correct it timely.

  8. SU-F-T-315: Comparative Studies of Planar Dose with Different Spatial Resolution for Head and Neck IMRT QA

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, T; Koo, T [Hallym University Medical Center, Chuncheon, Gangwon (Korea, Republic of)

    2016-06-15

    Purpose: To quantitatively investigate the planar dose difference and the γ value between the reference fluence map with the 1 mm detector-to-detector distance and the other fluence maps with less spatial resolution for head and neck intensity modulated radiation (IMRT) therapy. Methods: For ten head and neck cancer patients, the IMRT quality assurance (QA) beams were generated using by the commercial radiation treatment planning system, Pinnacle3 (ver. 8.0.d Philips Medical System, Madison, WI). For each beam, ten fluence maps (detector-to-detector distance: 1 mm to 10 mm by 1 mm) were generated. The fluence maps with larger than 1 mm detector-todetector distance were interpolated using MATLAB (R2014a, the Math Works,Natick, MA) by four different interpolation Methods: for the bilinear, the cubic spline, the bicubic, and the nearest neighbor interpolation, respectively. These interpolated fluence maps were compared with the reference one using the γ value (criteria: 3%, 3 mm) and the relative dose difference. Results: As the detector-to-detector distance increases, the dose difference between the two maps increases. For the fluence map with the same resolution, the cubic spline interpolation and the bicubic interpolation are almost equally best interpolation methods while the nearest neighbor interpolation is the worst.For example, for 5 mm distance fluence maps, γ≤1 are 98.12±2.28%, 99.48±0.66%, 99.45±0.65% and 82.23±0.48% for the bilinear, the cubic spline, the bicubic, and the nearest neighbor interpolation, respectively. For 7 mm distance fluence maps, γ≤1 are 90.87±5.91%, 90.22±6.95%, 91.79±5.97% and 71.93±4.92 for the bilinear, the cubic spline, the bicubic, and the nearest neighbor interpolation, respectively. Conclusion: We recommend that the 2-dimensional detector array with high spatial resolution should be used as an IMRT QA tool and that the measured fluence maps should be interpolated using by the cubic spline interpolation or the

  9. SU-F-P-54: Guidelines to Check Image Registration QA of a Clinical Deformation Registration Software: A Single Institution Preliminary Study

    Energy Technology Data Exchange (ETDEWEB)

    Gill, G; Souri, S; Rea, A; Chen, Y; Antone, J; Qian, X; Riegel, A; Taylor, P; Marrero, M; Diaz, F; Cao, Y; Jamshidi, A; Klein, E [Northwell Health, Lake Success, NY (United States); Barley, S; Sorell, V; Karangelis, G [Oncology Systems Limited, Longbow Close, Shrewsbury SY1 3GZ (United Kingdom); Button, T [Stony Brook University Hospital, Stony Brook, NY (United States)

    2016-06-15

    Purpose: The objective of this study is to verify and analyze the accuracy of a clinical deformable image registration (DIR) software. Methods: To test clinical DIR software qualitatively and quantitatively, we focused on lung radiotherapy and analyzed a single (Lung) patient CT scan. Artificial anatomical changes were applied to account for daily variations during the course of treatment including the planning target volume (PTV) and organs at risk (OAR). The primary CT (pCT) and the structure set (pST) was deformed with commercial tool (ImSimQA-Oncology Systems Limited) and after artificial deformation (dCT and dST) sent to another commercial tool (VelocityAI-Varian Medical Systems). In Velocity, the deformed CT and structures (dCT and dST) were inversely deformed back to original primary CT (dbpCT and dbpST). We compared the dbpST and pST structure sets using similarity metrics. Furthermore, a binary deformation field vector (BDF) was created and sent to ImSimQA software for comparison with known “ground truth” deformation vector fields (DVF). Results: An image similarity comparison was made by using “ground truth” DVF and “deformed output” BDF with an output of normalized “cross correlation (CC)” and “mutual information (MI)” in ImSimQA software. Results for the lung case were MI=0.66 and CC=0.99. The artificial structure deformation in both pST and dbpST was analyzed using DICE coefficient, mean distance to conformity (MDC) and deformation field error volume histogram (DFEVH) by comparing them before and after inverse deformation. We have noticed inadequate structure match for CTV, ITV and PTV due to close proximity of heart and overall affected by lung expansion. Conclusion: We have seen similarity between pCT and dbpCT but not so well between pST and dbpST, because of inadequate structure deformation in clinical DIR system. This system based quality assurance test will prepare us for adopting the guidelines of upcoming AAPM task group 132

  10. SU-F-P-54: Guidelines to Check Image Registration QA of a Clinical Deformation Registration Software: A Single Institution Preliminary Study

    International Nuclear Information System (INIS)

    Gill, G; Souri, S; Rea, A; Chen, Y; Antone, J; Qian, X; Riegel, A; Taylor, P; Marrero, M; Diaz, F; Cao, Y; Jamshidi, A; Klein, E; Barley, S; Sorell, V; Karangelis, G; Button, T

    2016-01-01

    Purpose: The objective of this study is to verify and analyze the accuracy of a clinical deformable image registration (DIR) software. Methods: To test clinical DIR software qualitatively and quantitatively, we focused on lung radiotherapy and analyzed a single (Lung) patient CT scan. Artificial anatomical changes were applied to account for daily variations during the course of treatment including the planning target volume (PTV) and organs at risk (OAR). The primary CT (pCT) and the structure set (pST) was deformed with commercial tool (ImSimQA-Oncology Systems Limited) and after artificial deformation (dCT and dST) sent to another commercial tool (VelocityAI-Varian Medical Systems). In Velocity, the deformed CT and structures (dCT and dST) were inversely deformed back to original primary CT (dbpCT and dbpST). We compared the dbpST and pST structure sets using similarity metrics. Furthermore, a binary deformation field vector (BDF) was created and sent to ImSimQA software for comparison with known “ground truth” deformation vector fields (DVF). Results: An image similarity comparison was made by using “ground truth” DVF and “deformed output” BDF with an output of normalized “cross correlation (CC)” and “mutual information (MI)” in ImSimQA software. Results for the lung case were MI=0.66 and CC=0.99. The artificial structure deformation in both pST and dbpST was analyzed using DICE coefficient, mean distance to conformity (MDC) and deformation field error volume histogram (DFEVH) by comparing them before and after inverse deformation. We have noticed inadequate structure match for CTV, ITV and PTV due to close proximity of heart and overall affected by lung expansion. Conclusion: We have seen similarity between pCT and dbpCT but not so well between pST and dbpST, because of inadequate structure deformation in clinical DIR system. This system based quality assurance test will prepare us for adopting the guidelines of upcoming AAPM task group 132

  11. Analytic and numerical studies of Scyllac equilibrium

    International Nuclear Information System (INIS)

    Barnes, D.C.; Brackbill, J.U.; Dagazian, R.Y.; Freidberg, J.P.; Schneider, W.; Betancourt, O.; Garabedian, P.

    1976-01-01

    The results of both numerical and analytic studies of the Scyllac equilibria are presented. Analytic expansions are used to derive equilibrium equations appropriate to noncircular cross sections, and compute the stellarator fields which produce toroidal force balance. Numerical algorithms are used to solve both the equilibrium equations and the full system of dynamical equations in three dimensions. Numerical equilibria are found for both l = 1,0 and l= 1,2 systems. It is found that the stellarator fields which produce equilibria in the l = 1.0 system are larger for diffuse than for sharp boundary plasma profiles, and that the stability of the equilibria depends strongly on the harmonic content of the stellarator fields

  12. Analytical study of doubly excited ridge states

    International Nuclear Information System (INIS)

    Wong, H.Y.

    1988-01-01

    Two different non-separable problems are explored and analyzed. Non-perturbative methods need to be used to handle them, as the competing forces involved in these problems are equally strong and do not yield to a perturbative analysis. The first one is the study of doubly excited ridge states of atoms, in which two electrons are comparably excited. An analytical wavefunction for such states is introduced and is used to solve the two-electron Hamiltonian in the pair coordinates called hyperspherical coordinates variationally. The correlation between the electrons is built in analytically into the structure of the wavefunction. Sequences of ridge states out to very high excitation are computed and are organized as Rydberg series converging to the double ionization limit. Numerical results of such states in He and H - are compared with other theoretical calculations where available. The second problem is the analysis of the photodetachment of negative ions in an electric field via the frame transformation theory. The presence of the electron field requires a transformation from spherical to cylindrical symmetry for the outgoing photoelectron. This gives an oscillatory modulating factor as the effect of the electric field on cross-sections. All of this work is derived analytically in a general form applicable to the photodetachment of any negative ion. The expressions are applied to H - and S - for illustration

  13. Application of QA geoscience investigations

    International Nuclear Information System (INIS)

    Henderson, J.T.

    1980-01-01

    This paper discusses the evolution of a classical hardware QA program (as currently embodied in DOE/ALO Manual Chapter 08XA; NRC 10CFR Part 50, Appendix B; and other similar documents) into the present geoscience quality assurance programs that address eventual NRC licensing, if required. In the context of this paper, QA will be restricted to the tasks associated with nuclear repositories, i.e. site identification, selection, characterization, verification, and utilization

  14. Impact of shade on outdoor thermal comfort—a seasonal field study in Tempe, Arizona

    Science.gov (United States)

    Middel, Ariane; Selover, Nancy; Hagen, Björn; Chhetri, Nalini

    2016-12-01

    Shade plays an important role in designing pedestrian-friendly outdoor spaces in hot desert cities. This study investigates the impact of photovoltaic canopy shade and tree shade on thermal comfort through meteorological observations and field surveys at a pedestrian mall on Arizona State University's Tempe campus. During the course of 1 year, on selected clear calm days representative of each season, we conducted hourly meteorological transects from 7:00 a.m. to 6:00 p.m. and surveyed 1284 people about their thermal perception, comfort, and preferences. Shade lowered thermal sensation votes by approximately 1 point on a semantic differential 9-point scale, increasing thermal comfort in all seasons except winter. Shade type (tree or solar canopy) did not significantly impact perceived comfort, suggesting that artificial and natural shades are equally efficient in hot dry climates. Globe temperature explained 51 % of the variance in thermal sensation votes and was the only statistically significant meteorological predictor. Important non-meteorological factors included adaptation, thermal comfort vote, thermal preference, gender, season, and time of day. A regression of subjective thermal sensation on physiological equivalent temperature yielded a neutral temperature of 28.6 °C. The acceptable comfort range was 19.1 °C-38.1 °C with a preferred temperature of 20.8 °C. Respondents exposed to above neutral temperature felt more comfortable if they had been in air-conditioning 5 min prior to the survey, indicating a lagged response to outdoor conditions. Our study highlights the importance of active solar access management in hot urban areas to reduce thermal stress.

  15. Modeling background radiation using geochemical data: A case study in and around Cameron, Arizona.

    Science.gov (United States)

    Marsac, Kara E; Burnley, Pamela C; Adcock, Christopher T; Haber, Daniel A; Malchow, Russell L; Hausrath, Elisabeth M

    2016-12-01

    This study compares high resolution forward models of natural gamma-ray background with that measured by high resolution aerial gamma-ray surveys. The ability to predict variations in natural background radiation levels should prove useful for those engaged in measuring anthropogenic contributions to background radiation for the purpose of emergency response and homeland security operations. The forward models are based on geologic maps and remote sensing multi-spectral imagery combined with two different sources of data: 1) bedrock geochemical data (uranium, potassium and thorium concentrations) collected from national databases, the scientific literature and private companies, and 2) the low spatial resolution NURE (National Uranium Resource Evaluation) aerial gamma-ray survey. The study area near Cameron, Arizona, is located in an arid region with minimal vegetation and, due to the presence of abandoned uranium mines, was the subject of a previous high resolution gamma-ray survey. We found that, in general, geologic map units form a good basis for predicting the geographic distribution of the gamma-ray background. Predictions of background gamma-radiation levels based on bedrock geochemical analyses were not as successful as those based on the NURE aerial survey data sorted by geologic unit. The less successful result of the bedrock geochemical model is most likely due to a number of factors including the need to take into account the evolution of soil geochemistry during chemical weathering and the influence of aeolian addition. Refinements to the forward models were made using ASTER visualizations to create subunits of similar exposure rate within the Chinle Formation, which contains multiple lithologies and by grouping alluvial units by drainage basin rather than age. Copyright © 2016 The Authors. Published by Elsevier Ltd.. All rights reserved.

  16. Impact of shade on outdoor thermal comfort-a seasonal field study in Tempe, Arizona.

    Science.gov (United States)

    Middel, Ariane; Selover, Nancy; Hagen, Björn; Chhetri, Nalini

    2016-12-01

    Shade plays an important role in designing pedestrian-friendly outdoor spaces in hot desert cities. This study investigates the impact of photovoltaic canopy shade and tree shade on thermal comfort through meteorological observations and field surveys at a pedestrian mall on Arizona State University's Tempe campus. During the course of 1 year, on selected clear calm days representative of each season, we conducted hourly meteorological transects from 7:00 a.m. to 6:00 p.m. and surveyed 1284 people about their thermal perception, comfort, and preferences. Shade lowered thermal sensation votes by approximately 1 point on a semantic differential 9-point scale, increasing thermal comfort in all seasons except winter. Shade type (tree or solar canopy) did not significantly impact perceived comfort, suggesting that artificial and natural shades are equally efficient in hot dry climates. Globe temperature explained 51 % of the variance in thermal sensation votes and was the only statistically significant meteorological predictor. Important non-meteorological factors included adaptation, thermal comfort vote, thermal preference, gender, season, and time of day. A regression of subjective thermal sensation on physiological equivalent temperature yielded a neutral temperature of 28.6 °C. The acceptable comfort range was 19.1 °C-38.1 °C with a preferred temperature of 20.8 °C. Respondents exposed to above neutral temperature felt more comfortable if they had been in air-conditioning 5 min prior to the survey, indicating a lagged response to outdoor conditions. Our study highlights the importance of active solar access management in hot urban areas to reduce thermal stress.

  17. Analytic scattering kernels for neutron thermalization studies

    International Nuclear Information System (INIS)

    Sears, V.F.

    1990-01-01

    Current plans call for the inclusion of a liquid hydrogen or deuterium cold source in the NRU replacement vessel. This report is part of an ongoing study of neutron thermalization in such a cold source. Here, we develop a simple analytical model for the scattering kernel of monatomic and diatomic liquids. We also present the results of extensive numerical calculations based on this model for liquid hydrogen, liquid deuterium, and mixtures of the two. These calculations demonstrate the dependence of the scattering kernel on the incident and scattered-neutron energies, the behavior near rotational thresholds, the dependence on the centre-of-mass pair correlations, the dependence on the ortho concentration, and the dependence on the deuterium concentration in H 2 /D 2 mixtures. The total scattering cross sections are also calculated and compared with available experimental results

  18. Analytical study of dissipative solitary waves

    Energy Technology Data Exchange (ETDEWEB)

    Dini, Fatemeh [Department of Physics, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of); Emamzadeh, Mehdi Molaie [Department of Physics, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of); Khorasani, Sina [School of Electrical Engineering, Sharif University of Technology, PO Box 11365-363, Tehran (Iran, Islamic Republic of); Bobin, Jean Louis [Universite Pierre et Marie Curie, Paris (France); Amrollahi, Reza [Department of Physics, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of); Sodagar, Majid [School of Electrical Engineering, Sharif University of Technology, PO Box 11365-363, Tehran (Iran, Islamic Republic of); Khoshnegar, Milad [School of Electrical Engineering, Sharif University of Technology, PO Box 11365-363, Tehran (Iran, Islamic Republic of)

    2008-02-15

    In this paper, the analytical solution to a new class of nonlinear solitons is presented with cubic nonlinearity, subject to a dissipation term arising as a result of a first-order derivative with respect to time, in the weakly nonlinear regime. Exact solutions are found using the combination of the perturbation and Green's function methods up to the third order. We present an example and discuss the asymptotic behavior of the Green's function. The dissipative solitary equation is also studied in the phase space in the non-dissipative and dissipative forms. Bounded and unbounded solutions of this equation are characterized, yielding an energy conversation law for non-dissipative waves. Applications of the model include weakly nonlinear solutions of terahertz Josephson plasma waves in layered superconductors and ablative Rayleigh-Taylor instability.

  19. Installation Restoration Program. Phase II, Stage 1. Problem Confirmation Study, Luke Air Force Base, Glendale, Arizona.

    Science.gov (United States)

    1984-11-01

    potable water in LAFB. Surface water from the Central Arizona Project (CAP) is available to the Base, but at a significantly higher cost than that of...available supplies of potable water which currently support the Base mission at LAFB. 1-16 1-16 SECTION 2 ENVIRONMENTAL SETTING 2.1 REGIONAL GEOLOGY Luke Air...the northern portion of the Base discharges toward the nearest natural surface water feature, the Agua Fria River. Figure 2-1 summarizes surface

  20. Graded approach for establishment of QA requirements for Type B packaging of radioactive material

    International Nuclear Information System (INIS)

    Fabian, R.R.; Woodruff, K.C.

    1988-01-01

    A study that was conducted by the Nuclear Regulatory Commission for the U.S. Congress to assess the effectiveness of quality assurance (QA) activities has demonstrated a need to modify and improve the application of QA requirements for the nuclear industry. As a result, the packaging community, along with the nuclear industry as a whole, has taken action to increase the efficacy of the QA function. The results of the study indicate that a graded approach for establishing QA requirements is the preferred method. The essence of the graded approach is the establishment of applicable QA requirements to an extent consistent with the importance to safety of an item, component, system, or activity. This paper describes the process that is used to develop the graded approach for QA requirements pertaining to Type B packaging

  1. Hydrosalinity studies of the Virgin River, Dixie Hot Springs, and Littlefield Springs, Utah, Arizona, and Nevada

    Science.gov (United States)

    Gerner, Steven J.; Thiros, Susan A.; Gerner, Steven J.; Thiros, Susan A.

    2014-01-01

    in the Virgin River Gorge containing known fault zones accounted for about 48 percent of this total seepage loss. An additional seepage loss of 6.7 ft3/s was calculated for the reach of the Virgin River between Bloomington, Utah, and the Utah/Arizona State line. This loss in flow is small compared to total flow in the river and is comparable to the rated error in streamflow measurements in this reach; consequently, it should be used with caution. Littlefield Springs were studied to determine the fraction of its discharge that originates as upstream seepage from the Virgin River and residence time of this water in the subsurface. Geochemical and environmental tracer data from groundwater and surface-water sites in the Virgin River Gorge area suggest that discharge from Littlefield Springs is a mixture of modern (post-1950s) seepage from the Virgin River upstream of the springs and older groundwater from a regional carbonate aquifer. Concentrations of the chlorofluorocarbons (CFCs) CFC-12 and CFC-113, chloride/fluoride and chloride/bromide ratios, and the stable isotope deuterium indicate that water discharging from Littlefield Springs is about 60 percent seepage from the Virgin River and about 40 percent discharge from the regional carbonate aquifer. The river seepage component was determined to have an average subsurface traveltime of about 26 ±1.6 years before discharging at Littlefield Springs. Radiocarbon data for Littlefield Springs suggest groundwater ages from 1,000 to 9,000 years. Because these are mixed waters, the component of discharge from the carbonate aquifer is likely much older than the groundwater ages suggested by the Littlefield Springs samples. If the dissolved-solids load from Dixie Hot Springs to the Virgin River were reduced, the irrigation water subsequently applied to agricultural fields in the St. George and Washington areas, which originates as water from the Virgin River downstream of Dixie Hot Springs, would have a lower dissolved

  2. Experimental analytical study on heat pipes

    International Nuclear Information System (INIS)

    Ismail, K.A.R.; Liu, C.Y.; Murcia, N.

    1981-01-01

    An analytical model is developed for optimizing the thickness distribution of the porous material in heat pipes. The method was used to calculate, design and construct heat pipes with internal geometrical changes. Ordinary pipes are also constructed and tested together with the modified ones. The results showed that modified tubes are superior in performance and that the analytical model can predict their performance to within 1.5% precision. (Author) [pt

  3. Nuclear analytical techniques for nanotoxicology studies

    International Nuclear Information System (INIS)

    Zhang, Z.Y.; Zhao, Y.L.; Chai, Z.F.

    2011-01-01

    With the rapid development of nanotechnology and its applications, a wide variety of nanomaterials are now used in commodities, pharmaceutics, cosmetics, biomedical products, and industries. The potential interactions of nanomaterials with living systems and the environment have attracted increasing attention from the public, as well as from manufacturers of nanomaterial-based products, academic researchers and policymakers. It is important to consider the environmental, health and safety aspects at an early stage of nanomaterial development and application in order to more effectively identify and manage potential human and environmental health impacts from nanomaterial exposure. This will require research in a range of areas, including detection and characterization, environmental fate and transport, ecotoxicology and toxicology. Nuclear analytical techniques (NATs) can play an important role in such studies due to their intrinsic merits such as high sensitivity, good accuracy, high space resolution, ability to distinguish the endogenous or exogenous sources of materials, and ability of in situ and in vivo analysis. In this paper, the applications of NATs in nanotoxicological and nano-ecotoxicological studies are outlined, and some recent results obtained in our laboratory are reported. (orig.)

  4. Physics acceptance and QA procedures for IMRT

    International Nuclear Information System (INIS)

    LoSasso, T.; Ling, C.

    2001-01-01

    Full text: Intensity modulated radiation therapy (IMRT) may improve tumor control without compromising normal tissues by facilitating higher, more conformal tumor doses relative to 3D CRT. Intensity modulation (IM) is now possible with inverse planning and radiation delivery using dynamic multileaf collimation. Compared to 3D CRT, certain components in the IMRT process are more obscure to the user. Thus, special quality assurance procedures are required. Hardware and software are still relatively new to many users, and the potential for error is unknown. The relationship between monitor unit (MU) setting and radiation dose for IM beams is much more complex than for non-IM fields. The leaf sequence computer files, which control the MLC position as a function of MU, are large and do not lend themselves to simple manual verification. The 'verification' port film for each IM treatment field, usually obtained with the MLC set at the extreme leaf positions for that field to outline the entire irradiated area, does not verify the intensity modulation pattern. Finally, in IMRT using DMLC (the so-called sliding window technique), a small error in the window (or gap) width will lead to a significant dose error. In earlier papers, we provided an evaluation of the mechanical and dosimetric aspects in the use of a MLC in the dynamic mode. Mechanical tolerances are significantly tighter for DMLC than for static MLC treatments. Transmission through the leaves and through rounded leaf ends and head scatter were shown to be significant to the accuracy of radiation dose delivery using DMLC. With these considerations, we concluded that the present DMLC hardware and software are effective for routine clinical implementation, provided that a carefully designed routine QA procedure is followed to assure the normality of operation. In our earlier studies, an evaluation of the long-term stability of DMLC operation had not yet been performed. This paper describes the current status of our

  5. Improvement of QA/QC activities in the construction of nuclear power plant

    International Nuclear Information System (INIS)

    Jinji Tomita; Shigetaka Tomaru

    1987-01-01

    Construction of commercial nuclear power plants in Japan started at around 1965. In this presentation are described quality assurance (QA) activities of a plant supplier who is a manufacturer of the key components as well. The QA activities until now are divided into several periods of the construction history in Japan. First term is 1960's when the QA activities are featured as the study and implementation through the construction of imported plants. Since then technologies and procedures of our own have been established and improved for the construction of high reliability plants. Our present QA activities are based on the active reflection of those lessons learned of past experiences. (author)

  6. Waste-management QA training and motivation

    International Nuclear Information System (INIS)

    Henderson, J.T.

    1982-01-01

    Early in the development of a QA Program for the Waste Management and Geotechnical Projects Directorate, thought was given to establishing a QA Training Program commensurate with the needs and appropriate to the motivation of a staff of more than 130 scientists and project leaders. These individuals, i.e., researchers rather than hardware designers, had no prior experience with QA programs, and from their perception generally did not believe that such controls had any merit. Therefore, historically proven approaches to QA training had to be quickly modified or totally discarded. For instance, due to the mobility and diversity of backgrounds of personnel at SNL, the QA training program had to accommodate many different levels of QA maturity at any given time. Furthermore, since the application of QA to R and D was continuing to profit from project-specific lessons learned, these improvements in the QA program had to be easily and quickly imparted in the general staff's evolving awareness of QA. A somewhat novel approach to QA training has been developed that draws heavily upon SNL's existing In-Hours Technical Education Courses (INTEC) studio capabilities. This training attempts to accommodate individual staff needs and to ensure the required QA skills and awareness for the diverse types of programs addressed

  7. Final audit report of remedial action construction at the UMTRA Project Mexican Hat, Utah -- Monument Valley, Arizona, sites

    International Nuclear Information System (INIS)

    1995-10-01

    The final audit report for remedial action at the Mexican Hat, Utah, Monument Valley, Arizona, Uranium Mill Tailings Remedial Action (UMTRA) Project sites consists of a summary of the radiological surveillances/audits, quality assurance (QA) in-process surveillances, and QA remedial action close-out inspections performed by the US Department of Energy (DOE) and the Technical Assistance Contractor (TAC); on-site construction reviews (OSCR) performed by the US Nuclear Regulatory Commission (NRC); and a surveillance performed by the Navajo Nation. This report refers to remedial action activities performed at the Mexican Hat, Utah--Monument Valley, Arizona, Uranium Mill Tailings Remedial Action (UMTRA) Project sites

  8. How Academic Department Chairs View the Influence of Corporate Ethics Scandals on Ethics Education in Arizona Business Schools: A Qualitative Case Study at the Postsecondary Level

    Science.gov (United States)

    Gillis, Robert James

    2017-01-01

    The purpose of this qualitative single case study was to explore how department chairs described the influence of recent corporate ethics scandals on content and availability of ethics education in postsecondary business schools in Arizona. The following research questions guided this study: RQ1: How do department chairs describe the influence of…

  9. An intensive two-week study of an urban CO2 dome in Phoenix, Arizona, USA

    International Nuclear Information System (INIS)

    Idso, C.D.; Balling, R.C. Jr.

    2001-01-01

    Atmospheric CO 2 concentrations were measured prior to dawn and in the middle of the afternoon at a height of 2m above the ground along four transects through the metropolitan area of Phoenix, Arizona on 14 consecutive days in January 2000. The data revealed the existence of a strong but variable urban CO 2 dome, which at one time exhibited a peak CO 2 concentration at the center of the city that was 75% greater than that of the surrounding rural area. Mean city-center peak enhancements, however, were considerably lower, averaging 43% on weekdays and 38% on weekends; and averaged over the entire commercial sector of the city, they were lower still, registering 30% on weekdays and 23% on weekends. Over the surrounding residential areas, on the other hand, there are no weekday-weekend differences in boundary-layer CO 2 concentration. Furthermore, because of enhanced vertical mixing during the day, near-surface CO 2 concentrations in the afternoon are typically reduced from what they are prior to sunrise. This situation is additionally perturbed by the prevailing southwest-to-northeast flow of air at that time of day, which lowers afternoon CO 2 concentrations on the southern and western edges of the city still more, as a consequence of the importation of pristine rural air. The southwest-to-northeast flow of air also sometimes totally compensates for the afternoon vertical-mixing-induced loss of CO 2 from areas on the northern and eastern sides of the city, as a consequence of the northeastward advection of CO 2 emanating from the central, southern and western sectors of the city. Hence, although complex, the nature of the urban CO 2 dome of Phoenix, Arizona, is readily understandable in terms of basic meteorological phenomena and their interaction with human activities occurring at the land/air interface. (Author)

  10. Culturally Responsive Active Citizenship Education for Newcomer Students: A Cross-State Case Study of Two Teachers in Arizona and New York

    Science.gov (United States)

    Ramirez, Pablo; Jaffee, Ashley Taylor

    2016-01-01

    This paper examines how two social studies teachers in New York and Arizona engage newcomer youth in active citizenship education. Using a framework of culturally responsive active citizenship education, this article sheds light on how two teachers, in two different social, political, and educational contexts, enact critical citizenship practices…

  11. QA manpower requirement for nuclear power plants

    International Nuclear Information System (INIS)

    Link, M.

    1980-01-01

    To ensure the quality of the plant, QA activities are to be performed by the owner, the main contractor, the subcontractors and the Licensing Authority. The responsibilities of the QA-personnel of these organizations comprise as a minimum the control of the quality assurance systems and the proof of the quality requirements. Numbers of the required QA-personnel, designated for different tasks and recommended educational levels and professional qualifications will be given. (orig./RW)

  12. Holistic versus Analytic Evaluation of EFL Writing: A Case Study

    Science.gov (United States)

    Ghalib, Thikra K.; Al-Hattami, Abdulghani A.

    2015-01-01

    This paper investigates the performance of holistic and analytic scoring rubrics in the context of EFL writing. Specifically, the paper compares EFL students' scores on a writing task using holistic and analytic scoring rubrics. The data for the study was collected from 30 participants attending an English undergraduate program in a Yemeni…

  13. Impact and payback of a QA/QC program for steam-water chemistry

    International Nuclear Information System (INIS)

    Lerman, S.I.; Wilson, D.

    1992-01-01

    QA/QC programs for analytical laboratories and in-line instrumentation are essential if we are to have any faith in the data they produce. When the analytes are at trace levels, as they frequently are in a steam-water cycle, the importance of QA/QC increases by an order of magnitude. The cost and resources of such a program, although worth it, are frequently underestimated. QA/QC is much more than running a standard several times a week. This paper will discuss some of the essential elements of such a program, compare them to the cost, and point out the impact of not having such a program. RP-2712-3 showed how essential QA/QC is to understand the limitations of instruments doing trace analysis of water. What it did not do, nor was it intended to, is discuss how good reliability can be in your own plant. QA programs that include training of personnel, written procedures, and comprehensive maintenance and inventory programs ensure optimum performance of chemical monitors. QC samples run regularly allow plant personnel to respond to poor performance in a timely manner, appropriate to plant demands. Proper data management establishes precision information necessary to determine how good our measurements are. Generally, the plant has the advantage of a central laboratory to perform corroborative analysis, and a comprehensive QA/QC program will integrate the plant monitoring operations with the central lab. Where trace analysis is concerned, attention to detail becomes paramount. Instrument performance may be below expected levels, and instruments are probably being run at the bottom end of their optimum range. Without QA/QC the plant manager can have no confidence in analytical results. Poor steam-water chemistry can go unnoticed, causing system deterioration. We can't afford to wait for another RP-2712-3 to tell us how good our data is

  14. Follow-up utterances in QA dialogue

    NARCIS (Netherlands)

    van Schooten, B.W.; op den Akker, Hendrikus J.A.

    2006-01-01

    The processing of user follow-up utterances by a QA system is a topic which is still in its infant stages, but enjoys growing interest in the QA community. In this paper, we discuss the broader issues related to handling follow-up utterances in a real-life "information kiosk" setting. With help of a

  15. QA

    International Nuclear Information System (INIS)

    Anon.

    1984-01-01

    Koeberg's system for quality assurance was discussed with the Quality Assurance Programme Manager for Koeberg Construction. An American style of quality assurance, practised on French technology is used for Koeberg. The quality assurance that is practised at Koeberg, also affected other industries in South Africa

  16. Applying QA to nuclear-development programs

    International Nuclear Information System (INIS)

    Caplinger, W.H.

    1981-12-01

    The application of quality assurance (QA) principles to developmental programs is usually accomplished by tailoring or selecting appropriate requirements from large QA systems. Developmental work at Westinghouse Hanford Company (WHC) covers the complete range from basic research to in-core reactor tests. Desired requirements are selected from the 18 criteria in ANSI/ASME NQA Standard 1 by the cognizant program engineer in conjunction with the quality engineer. These referenced criteria assure that QA for the program is planned, implemented, and maintained. In addition, the WHC QA Manual provides four categories or levels of QA that are assigned to programs or components within the program. These categories are based on safety, reliability, and consequences of failure to provide a cost effective program

  17. STRengthening analytical thinking for observational studies

    DEFF Research Database (Denmark)

    Sauerbrei, Willi; Abrahamowicz, Michal; Altman, Douglas G.

    2014-01-01

    The validity and practical utility of observational medical research depends critically on good study design, excellent data quality, appropriate statistical methods and accurate interpretation of results. Statistical methodology has seen substantial development in recent times. Unfortunately, ma...

  18. Electrochemical, surface analytical and quantum chemical studies ...

    Indian Academy of Sciences (India)

    subject of numerous studies due to their high technological value and wide range .... Mulliken population analysis of atoms in triazole derivatives, depending on the ... 2102–0003) with an accelerating voltage of 20 kV, at a scan speed=slow 5 and ... the corrosion rate can also be determined by Tafel extra- polation of either ...

  19. Backache amongst soldiers: a prospective analytical study

    International Nuclear Information System (INIS)

    Ilyas, S.; Rehman, A.U.; Janjua, S.H.; Tarrar, A.M.

    2012-01-01

    Objective: To investigate the occupational predispositions of low back pain in soldiers Study Design: Descriptive study. Place and Duration of Study: Combined Military Hospital, Bahawalpur, from June 2009 to Jan 2010. Patients and Methods: A questionnaire was developed to investigate the occupation-related issues in soldiers reporting with low backache in surgical OPD at CMH Bahawalpur. It included personal and occupational factors. The body mass index was also calculated. Of the 107 male soldiers assessed, 90 were enrolled into the study. The statistical analysis was performed by descriptive analysis of the data using SPSS 17.0. Results: Of all the soldiers evaluated (n=90), 32 (35.6%) were clerks/computer operators, 21 (23.1%) were drivers and 14(15.6%) were signal men. All were males (100%) and the average BMI was 24.8 kg/m2. The 69 (76.7%) patients who had backache had prolonged working hours (average 10.8 hours per day), 68 (75.6%) patients used to sleep over tape/nawar bed and only 12 (13.3%) had been sleeping on mattresses. The onset of pain was sudden in 58 (64.4%) patients. 27 (23.3%) had developed acute backache after prolonged sitting, 21 (30%) after lifting heavy objects. The pain was exaggerated by doing morning physical training 82 (91.1%), prolonged sitting 61 (67.8%) and standing with rifle 24 (26.7%). Conclusion: The prevalence of low back pain in sedentary occupation or soldiers on sitting jobs was higher 69 (76%). The number of working hours on these occupations was associated with occurrence as well as aggravation of low back pain. (author)

  20. Moving from gamma passing rates to patient DVH-based QA metrics in pretreatment dose QA

    Energy Technology Data Exchange (ETDEWEB)

    Zhen, Heming; Nelms, Benjamin E.; Tome, Wolfgang A. [Department of Medical Physics, University of Wisconsin, Madison, Wisconsin 53705 (United States); Department of Human Oncology, University of Wisconsin, Madison, Wisconsin 53792 and Canis Lupus LLC, Merrimac, Wisconsin 53561 (United States); Department of Medical Physics, University of Wisconsin, Madison, Wisconsin 53705 and Department of Human Oncology, University of Wisconsin, Madison, Wisconsin 53792 (United States)

    2011-10-15

    considerable scatter in the gamma passing rate vs DVH-based metric curves. However, for the same input data, the PDP estimates were in agreement with actual patient DVH results. Conclusions: Gamma passing rate, even if calculated based on patient dose grids, has generally weak correlation to critical patient DVH errors. However, the PDP algorithm was shown to accurately predict the DVH impact using conventional planar QA results. Using patient-DVH-based metrics IMRT QA allows per-patient dose QA to be based on metrics that are both sensitive and specific. Further studies are now required to analyze new processes and action levels associated with DVH-based metrics to ensure effectiveness and practicality in the clinical setting.

  1. Process control analysis of IMRT QA: implications for clinical trials

    International Nuclear Information System (INIS)

    Pawlicki, Todd; Rice, Roger K; Yoo, Sua; Court, Laurence E; McMillan, Sharon K; Russell, J Donald; Pacyniak, John M; Woo, Milton K; Basran, Parminder S; Boyer, Arthur L; Bonilla, Claribel

    2008-01-01

    The purpose of this study is two-fold: first is to investigate the process of IMRT QA using control charts and second is to compare control chart limits to limits calculated using the standard deviation (σ). Head and neck and prostate IMRT QA cases from seven institutions in both academic and community settings are considered. The percent difference between the point dose measurement in phantom and the corresponding result from the treatment planning system (TPS) is used for analysis. The average of the percent difference calculations defines the accuracy of the process and is called the process target. This represents the degree to which the process meets the clinical goal of 0% difference between the measurements and TPS. IMRT QA process ability defines the ability of the process to meet clinical specifications (e.g. 5% difference between the measurement and TPS). The process ability is defined in two ways: (1) the half-width of the control chart limits, and (2) the half-width of ±3σ limits. Process performance is characterized as being in one of four possible states that describes the stability of the process and its ability to meet clinical specifications. For the head and neck cases, the average process target across institutions was 0.3% (range: -1.5% to 2.9%). The average process ability using control chart limits was 7.2% (range: 5.3% to 9.8%) compared to 6.7% (range: 5.3% to 8.2%) using standard deviation limits. For the prostate cases, the average process target across the institutions was 0.2% (range: -1.8% to 1.4%). The average process ability using control chart limits was 4.4% (range: 1.3% to 9.4%) compared to 5.3% (range: 2.3% to 9.8%) using standard deviation limits. Using the standard deviation to characterize IMRT QA process performance resulted in processes being preferentially placed in one of the four states. This is in contrast to using control charts for process characterization where the IMRT QA processes were spread over three of the

  2. Terrestrial precipitation and soil moisture: A case study over southern Arizona and data development

    Science.gov (United States)

    Stillman, Susan

    Quantifying climatological precipitation and soil moisture as well as interannual variability and trends requires extensive observation. This work focuses on the analysis of available precipitation and soil moisture data and the development of new ways to estimate these quantities. Precipitation and soil moisture characteristics are highly dependent on the spatial and temporal scales. We begin at the point scale, examining hourly precipitation and soil moisture at individual gauges. First, we focus on the Walnut Gulch Experimental Watershed (WGEW), a 150 km2 area in southern Arizona. The watershed has been measuring rainfall since 1956 with a very high density network of approximately 0.6 gauges per km2. Additionally, there are 19 soil moisture probes at 5 cm depth with data starting in 2002. In order to extend the measurement period, we have developed a water balance model which estimates monsoon season (Jul-Sep) soil moisture using only precipitation for input, and calibrated so that the modeled soil moisture fits best with the soil moisture measured by each of the 19 probes from 2002-2012. This observationally constrained soil moisture is highly correlated with the collocated probes (R=0.88), and extends the measurement period from 10 to 56 years and the number of gauges from 19 to 88. Then, we focus on the spatiotemporal variability within the watershed and the ability to estimate area averaged quantities. Spatially averaged precipitation and observationally constrained soil moisture from the 88 gauges is then used to evaluate various gridded datasets. We find that gauge-based precipitation products perform best followed by reanalyses and then satellite-based products. Coupled Model Intercomparison Project Phase 5 (CMIP5) models perform the worst and overestimate cold season precipitation while offsetting the monsoon peak precipitation forward or backward by a month. Satellite-based soil moisture is the best followed by land data assimilation systems and

  3. Analytical electron microscope study of eight ataxites

    Science.gov (United States)

    Novotny, P. M.; Goldstein, J. I.; Williams, D. B.

    1982-01-01

    Optical and electron optical (SEM, TEM, AEM) techniques were employed to investigate the fine structure of eight ataxite-iron meteorites. Structural studies indicated that the ataxites can be divided into two groups: a Widmanstaetten decomposition group and a martensite decomposition group. The Widmanstaetten decomposition group has a Type I plessite microstructure and the central taenite regions contain highly dislocated lath martensite. The steep M shaped Ni gradients in the taenite are consistent with the fast cooling rates, of not less than 500 C/my, observed for this group. The martensite decomposition group has a Type III plessite microstructure and contains all the chemical group IVB ataxites. The maximum taenite Ni contents vary from 47.5 to 52.7 wt % and are consistent with slow cooling to low temperatures of not greater than 350 C at cooling rates of not greater than 25 C/my.

  4. Analytical study of anisotropic compact star models

    Energy Technology Data Exchange (ETDEWEB)

    Ivanov, B.V. [Bulgarian Academy of Science, Institute for Nuclear Research and Nuclear Energy, Sofia (Bulgaria)

    2017-11-15

    A simple classification is given of the anisotropic relativistic star models, resembling the one of charged isotropic solutions. On the ground of this database, and taking into account the conditions for physically realistic star models, a method is proposed for generating all such solutions. It is based on the energy density and the radial pressure as seeding functions. Numerous relations between the realistic conditions are found and the need for a graphic proof is reduced just to one pair of inequalities. This general formalism is illustrated with an example of a class of solutions with linear equation of state and simple energy density. It is found that the solutions depend on three free constants and concrete examples are given. Some other popular models are studied with the same method. (orig.)

  5. Analytical study in 1D nuclear waste migration

    International Nuclear Information System (INIS)

    Perez Guerrero, Jesus S.; Heilbron Filho, Paulo L.; Romani, Zrinka V.

    1999-01-01

    The simulation of the nuclear waste migration phenomena are governed mainly by diffusive-convective equation that includes the effects of hydrodynamic dispersion (mechanical dispersion and molecular diffusion), radioactive decay and chemical interaction. For some special problems (depending on the boundary conditions and when the domain is considered infinite or semi-infinite) an analytical solution may be obtained using classical analytical methods such as Laplace Transform or variable separation. The hybrid Generalized Integral Transform Technique (GITT) is a powerful tool that can be applied to solve diffusive-convective linear problems to obtain formal analytical solutions. The aim of this work is to illustrate that the GITT may be used to obtain an analytical formal solution for the study of migration of radioactive waste in saturated flow porous media. A case test considering 241 Am radionuclide is presented. (author)

  6. Analytical Study of Active Prosthetic Legs

    Science.gov (United States)

    Ono, Kyosuke; Katsumata, Mie

    Walking with prosthesis has not been well analyzed mathematically and it seems that the design of powered prosthesis has been done empirically so far. This paper presents a dynamic simulation of a normal human walking and walking with an active prosthesis. We also studied the two controlling methods of a powered thigh prosthesis based on multi-body simulation of human walking. First we measured the normal human walking gait, then, we showed that a 3-DOF human walking model can walk on level ground by applying tracking control to the measured walking gait within a certain range of tuned walking period. Next, we applied the tracking control and self-excited control to the powered thigh prosthesis and compared the robustness and efficiency of the two control methods by numerical simulation. As a result, we found that the self-excited control can significantly decrease the hip joint torque and specific cost to 1/3 compared with the tracking control. Moreover, the self-excited control is superior to the tracking control because tuning for the walking period is not needed for the active prosthetic leg.

  7. AN ANALYTICAL STUDY IN ADHESIVE BOWEL OBSTRUCTION

    Directory of Open Access Journals (Sweden)

    Gerald Anand Raja

    2017-04-01

    Full Text Available BACKGROUND Peritoneal adhesions can be defined as abnormal fibrous bands between organs or tissues or both in the abdominal cavity that are normally separated. Adhesions may be acquired or congenital; however, most are acquired as a result of peritoneal injury, the most common cause of which is abdominopelvic surgery. Less commonly, adhesions may form as the result of inflammatory conditions, intraperitoneal infection or abdominal trauma. The extent of adhesion formation varies from one patient to another and is most dependent on the type and magnitude of surgery performed as well as whether any postoperative complications develop. Fortunately, most patients with adhesions do not experience any overt clinical symptoms. For others, adhesions may lead to any one of a host of problems and can be the cause of significant morbidity and mortality. MATERIALS AND METHODS This is a retrospective study of 50 patients admitted in Government Royapettah Hospital with adhesive bowel obstruction between September 2008 to September 2010. All patients were admitted and managed either conservatively or surgically. RESULTS 1. Adhesive bowel disease is the most common cause for bowel obstruction followed by hernias. 2. Increased incidence is noted in females. 3. Increased incidence of adhesions was documented in gynaecological and colorectal surgeries. 4. Below umbilical incisions have higher propensity for adhesion formation. 5. Laparotomies done for infective aetiology have higher adhesion risks. 6. Most of adhesive obstructions can be managed conservatively. 7. Adhesiolysis preferably laparoscopic can be done. For gangrenous bowel resection and anastomosis or ostomy done. 8. Given the above risk factors, adhesive bowel disease can be prevented to a certain extent. CONCLUSION The formation of peritoneal adhesions continues to plague patients, surgeons and society. Although, research in this area is ongoing, there is currently no method that is 100% effective in

  8. Land-Use Mapping in a Mixed Urban-Agricultural Arid Landscape Using Object-Based Image Analysis: A Case Study from Maricopa, Arizona

    Directory of Open Access Journals (Sweden)

    Christopher S. Galletti

    2014-06-01

    Full Text Available Land-use mapping is critical for global change research. In Central Arizona, U.S.A., the spatial distribution of land use is important for sustainable land management decisions. The objective of this study was to create a land-use map that serves as a model for the city of Maricopa, an expanding urban region in the Sun Corridor of Arizona. We use object-based image analysis to map six land-use types from ASTER imagery, and then compare this with two per-pixel classifications. Our results show that a single segmentation, combined with intermediary classifications and merging, morphing, and growing image-objects, can lead to an accurate land-use map that is capable of utilizing both spatial and spectral information. We also employ a moving-window diversity assessment to help with analysis and improve post-classification modifications.

  9. March 2014 Arizona thoracic society notes

    OpenAIRE

    Robbins RA

    2014-01-01

    No abstract available. Article truncated after 150 words. The March 2014 Arizona Thoracic Society meeting was a special meeting. In conjunction with the Valley Fever Center for Excellence and the Arizona Respiratory Center the Eighteenth Annual Farness Lecture was held in the Sonntag Pavilion at St. Joseph's Hospital at 6 PM on Friday, April 4, 2014. The guest speaker was Antonio "Tony" Catanzaro, MD from the University of California San Diego and current president of the Cocci Study Group. T...

  10. Analytical and numerical studies of creation probabilities of hierarchical trees

    Directory of Open Access Journals (Sweden)

    S.S. Borysov

    2011-03-01

    Full Text Available We consider the creation conditions of diverse hierarchical trees both analytically and numerically. A connection between the probabilities to create hierarchical levels and the probability to associate these levels into a united structure is studied. We argue that a consistent probabilistic picture requires the use of deformed algebra. Our consideration is based on the study of the main types of hierarchical trees, among which both regular and degenerate ones are studied analytically, while the creation probabilities of Fibonacci, scale-free and arbitrary trees are determined numerically.

  11. Analytical study on model tests of soil-structure interaction

    International Nuclear Information System (INIS)

    Odajima, M.; Suzuki, S.; Akino, K.

    1987-01-01

    Since nuclear power plant (NPP) structures are stiff, heavy and partly-embedded, the behavior of those structures during an earthquake depends on the vibrational characteristics of not only the structure but also the soil. Accordingly, seismic response analyses considering the effects of soil-structure interaction (SSI) are extremely important for seismic design of NPP structures. Many studies have been conducted on analytical techniques concerning SSI and various analytical models and approaches have been proposed. Based on the studies, SSI analytical codes (computer programs) for NPP structures have been improved at JINS (Japan Institute of Nuclear Safety), one of the departments of NUPEC (Nuclear Power Engineering Test Center) in Japan. These codes are soil-spring lumped-mass code (SANLUM), finite element code (SANSSI), thin layered element code (SANSOL). In proceeding with the improvement of the analytical codes, in-situ large-scale forced vibration SSI tests were performed using models simulating light water reactor buildings, and simulation analyses were performed to verify the codes. This paper presents an analytical study to demonstrate the usefulness of the codes

  12. QA CLASSIFICATION ANALYSIS OF GROUND SUPPORT SYSTEMS

    International Nuclear Information System (INIS)

    D. W. Gwyn

    1996-01-01

    The purpose and objective of this analysis is to determine if the permanent function Ground Support Systems (CI: BABEEOOOO) are quality-affecting items and if so, to establish the appropriate Quality Assurance (QA) classification

  13. Radioactivity in the environment; a case study of the Puerco and Little Colorado River basins, Arizona and New Mexico

    Science.gov (United States)

    Wirt, Laurie

    1994-01-01

    This report, written for the nontechnical reader, summarizes the results of a study from 1988-91 of the occurrence and transport of selected radionuclides and other chemical constituents in the Puerco and Little Colorado River basins, Arizona and New Mexico. More than two decades of uranium mining and the 1979 failure of an earthen dam containing mine tailings released high levels of radionuclides and other chemical constituents to the Puerco River, a tributary of the Little Colorado River. Releases caused public concern that ground water and streamflow downstream from mining were contaminated. Study findings show which radioactive elements are present, how these elements are distributed between water and sediment in the environment, how concentrations of radioactive elements vary naturally within basins, and how levels of radioactivity have changed since the end of mining. Although levels of radioactive elements and other trace elements measured in streamflow commonly exceed drinking-water standards, no evidence was found to indicate that the high concentrations were still related to uraniurn mining. Sediment radioactivity was higher at sample sites on streams that drain the eastern part of the Little Colorado River basin than that of samples from the western part. Radioactivity of suspended sediment measured in this study, therefore, represents natural conditions for the streams sampled rather than an effect of mining. Because ground water beneath the Puerco River channel is shallow, the aquifer is vulnerable to contamination. A narrow zone of ground water beneath the Puerco River containing elevated uranium concentrations was identified during the study. The highest concentrations were nearest the mines and in samples collected in the first few feet beneath the streambed. Natuxal radiation levels in a few areas of the underlying sedimentary aquifer not connected to the Puerco River also exceeded water quality standards. Water testing would enable those residents

  14. Radioactivity in the environment: a case study of the Puerco and Little Colorado River Basins, Arizona and New Mexico

    International Nuclear Information System (INIS)

    Wirt, L.

    1994-01-01

    This report, written for the nontechnical reader, summarizes the results of a study from 1988-91 of the occurrence and transport of selected radionuclides and other chemical constituents in the Puerco and Little Colorado River basins, Arizona and New Mexico. More than two decades of uranium mining and the 1979 failure of an earthen dam containing mine tailings released high levels of radionuclides and other chemical constituents to the Puerco River, a tributary of the Little Colorado River. Releases caused public concern that ground water and streamflow downstream from mining were contaminated. Study findings show which radioactive elements are present, how these elements are distributed between water and sediment in the environment, how concentrations of radioactive elements vary naturally within basins, and how levels of radioactivity have changed since the end of mining. Although levels of radioactive elements and other trace elements measured in streamflow commonly exceed drinking-water standards, no evidence was found to indicate that the high concentrations were still related to uraniurn mining. Sediment radioactivity was higher at sample sites on streams that drain the eastern part of the Little Colorado River basin than that of samples from the western part. Radioactivity of suspended sediment measured in this study, therefore, represents natural conditions for the streams sampled rather than an effect of mining. Because ground water beneath the Puerco River channel is shallow, the aquifer is vulnerable to contamination. A narrow zone of ground water beneath the Puerco River containing elevated uranium concentrations was identified during the study. The highest concentrations were nearest the mines and in samples collected in the first few feet beneath the streambed. Natuxal radiation levels in a few areas of the underlying sedimentary aquifer not connected to the Puerco River also exceeded water quality standards. Water testing would enable those residents

  15. Analytical and Numerical Studies of Sloshing in Tanks

    Energy Technology Data Exchange (ETDEWEB)

    Solaas, F

    1996-12-31

    For oil cargo ship tanks and liquid natural gas carriers, the dimensions of the tanks are often such that the highest resonant sloshing periods and the ship motions are in the same period range, which may cause violent resonant sloshing of the liquid. In this doctoral thesis, linear and non-linear analytical potential theory solutions of the sloshing problem are studied for a two-dimensional rectangular tank and a vertical circular cylindrical tank, using perturbation technique for the non-linear case. The tank is forced to oscillate harmonically with small amplitudes of sway with frequency in the vicinity of the lowest natural frequency of the fluid inside the tank. The method is extended to other tank shapes using a combined analytical and numerical method. A boundary element numerical method is used to determine the eigenfunctions and eigenvalues of the problem. These are used in the non-linear analytical free surface conditions, and the velocity potential and free surface elevation for each boundary value problem in the perturbation scheme are determined by the boundary element method. Both the analytical method and the combined analytical and numerical method are restricted to tanks with vertical walls in the free surface. The suitability of a commercial programme, FLOW-3D, to estimate sloshing is studied. It solves the Navier-Stokes equations by the finite difference method. The free surface as function of time is traced using the fractional volume of fluid method. 59 refs., 54 figs., 37 tabs.

  16. Analytical and Numerical Studies of Sloshing in Tanks

    Energy Technology Data Exchange (ETDEWEB)

    Solaas, F.

    1995-12-31

    For oil cargo ship tanks and liquid natural gas carriers, the dimensions of the tanks are often such that the highest resonant sloshing periods and the ship motions are in the same period range, which may cause violent resonant sloshing of the liquid. In this doctoral thesis, linear and non-linear analytical potential theory solutions of the sloshing problem are studied for a two-dimensional rectangular tank and a vertical circular cylindrical tank, using perturbation technique for the non-linear case. The tank is forced to oscillate harmonically with small amplitudes of sway with frequency in the vicinity of the lowest natural frequency of the fluid inside the tank. The method is extended to other tank shapes using a combined analytical and numerical method. A boundary element numerical method is used to determine the eigenfunctions and eigenvalues of the problem. These are used in the non-linear analytical free surface conditions, and the velocity potential and free surface elevation for each boundary value problem in the perturbation scheme are determined by the boundary element method. Both the analytical method and the combined analytical and numerical method are restricted to tanks with vertical walls in the free surface. The suitability of a commercial programme, FLOW-3D, to estimate sloshing is studied. It solves the Navier-Stokes equations by the finite difference method. The free surface as function of time is traced using the fractional volume of fluid method. 59 refs., 54 figs., 37 tabs.

  17. NORTH END ROADLESS AREA, ARIZONA.

    Science.gov (United States)

    Drewes, Harald; Bigsby, P.R.

    1984-01-01

    Studies conducted in the North End Roadless Area, Arizona indicate probable or substantiated metallic mineral-resource potential in about one-fifth of the area. The area has potential for disseminated or stockwork-type molybdenum mineralization, copper-lead-zinc-silver veins, lead-zinc-silver limestone replacement deposits, and tungsten-bearing contact metamorphic skarn deposits. The area also contains cement rock and marble dimension stone, but has only slight promise for the occurrence of petroleum and natural gas.

  18. Archetypes of Supply Chain Analytics Initiatives—An Exploratory Study

    Directory of Open Access Journals (Sweden)

    Tino T. Herden

    2018-05-01

    Full Text Available While Big Data and Analytics are arguably rising stars of competitive advantage, their application is often presented and investigated as an overall approach. A plethora of methods and technologies combined with a variety of objectives creates a barrier for managers to decide how to act, while researchers investigating the impact of Analytics oftentimes neglect this complexity when generalizing their results. Based on a cluster analysis applied to 46 case studies of Supply Chain Analytics (SCA we propose 6 archetypes of initiatives in SCA to provide orientation for managers as means to overcome barriers and build competitive advantage. Further, the derived archetypes present a distinction of SCA for researchers seeking to investigate the effects of SCA on organizational performance.

  19. Analytical studies related to Indian PHWR containment system performance

    International Nuclear Information System (INIS)

    Haware, S.K.; Markandeya, S.G.; Ghosh, A.K.; Kushwaha, H.S.; Venkat Raj, V.

    1998-01-01

    Build-up of pressure in a multi-compartment containment after a postulated accident, the growth, transportation and removal of aerosols in the containment are complex processes of vital importance in deciding the source term. The release of hydrogen and its combustion increases the overpressure. In order to analyze these complex processes and to enable proper estimation of the source term, well tested analytical tools are necessary. This paper gives a detailed account of the analytical tools developed/adapted for PSA level 2 studies. (author)

  20. Preliminary study of N[sub 2]O flux over irrigated Bermudagrass in a desert environment. [USA - Arizona

    Energy Technology Data Exchange (ETDEWEB)

    Matthias, A.D.; Artiola, J.F.; Musil, S.A. (Arizona University, Tucson, AZ (USA). Dept. of Soil and Water Science)

    1993-04-01

    The increase of atmospheric nitrous oxide is believed to be related to human activities, including increased agricultural use of nitrogen (N) fertilizers and irrigation. The purpose of this study was to evaluate N[sub 2]O flux (F(N)) into the atmosphere using chamber and gradient profile methods over an irrigated, N fertilized, bermudagrass (Cynodon dactylon cv. 'Midiron') field in the Sonoran Desert of Arizona. For the gradient profile method it was hypothesized that locally stable atmospheric conditions would enhance N[sub 2]O concentration differences sufficiently (more than approximately) 4 nl l[sup -1] to be resolved by gas chromatographic analysis of air samples collected at two heights (0.05 and 3.3 m) over the field. Significant differences (205 and 30 nl l[sup -1]) in mean concentration occurred during two sampling intervals in late afternoon and early morning of a 24 h period on 18-19 July 1991. During those intervals the surface layer was stable and relatively large F(N) estimated by the chamber method (371 and 48 ng m[sup -2] s[sup -1]) were comparable with F(N) estimated by the gradient profile method (283 and 101 ng m[sup -2] s[sup -1]). Simulations based on similarity theory indicate that resolution of N[sub 2]O concentration differences less than l nl l[sup -1] was required, but could not be achieved, when the surface layer was unstable and/or F(N) was small. Analysis also indicates that uncertainty of F(N) estimated by the chamber method was reduced slightly by estimation of temporal variation of vapour pressure in chamber air.

  1. Case Study : Visual Analytics in Software Product Assessments

    NARCIS (Netherlands)

    Telea, Alexandru; Voinea, Lucian; Lanza, M; Storey, M; Muller, H

    2009-01-01

    We present how a combination of static source code analysis, repository analysis, and visualization techniques has been used to effectively get and communicate insight in the development and project management problems of a large industrial code base. This study is an example of how visual analytics

  2. Mineral resources of the Muggins Mountains Wilderness Study Area, Yuma County, Arizona

    International Nuclear Information System (INIS)

    Smith, D.B.; Tosdal, R.M.; Pitkin, J.A.; Kleinkopf, M.D.; Wood, R.H.

    1989-01-01

    The Muggins Mountains Wilderness Study Area covers approximately 8,855 acres immediately south of the Yuma Proving Ground. This study area contains sand and gravel, and it has a moderate potential for gold in placer deposits. One small drainage basin along the southeast boundary of this study area has a moderate potential for uranium. This study area has a low potential for geothermal energy and for oil and gas resources

  3. Microwave magnetoelectric fields: An analytical study of topological characteristics

    Energy Technology Data Exchange (ETDEWEB)

    Joffe, R., E-mail: ioffr1@gmail.com [Microwave Magnetic Laboratory, Department of Electrical and Computer Engineering, Ben Gurion University of the Negev, Beer Sheva (Israel); Department of Electrical and Electronics Engineering, Shamoon College of Engineering, Beer Sheva (Israel); Shavit, R.; Kamenetskii, E.O. [Microwave Magnetic Laboratory, Department of Electrical and Computer Engineering, Ben Gurion University of the Negev, Beer Sheva (Israel)

    2015-10-15

    The near fields originated from a small quasi-two-dimensional ferrite disk with magnetic-dipolar-mode (MDM) oscillations are the fields with broken dual (electric-magnetic) symmetry. Numerical studies show that such fields – called the magnetoelectric (ME) fields – are distinguished by the power-flow vortices and helicity parameters (E.O. Kamenetskii, R. Joffe, R. Shavit, Phys. Rev. E 87 (2013) 023201). These numerical studies can well explain recent experimental results with MDM ferrite disks. In the present paper, we obtain analytically topological characteristics of the ME-field modes. For this purpose, we used a method of successive approximations. In the second approximation we take into account the influence of the edge regions of an open ferrite disk, which are excluded in the first-approximation solving of the magnetostatic (MS) spectral problem. Based on the analytical method, we obtain a “pure” structure of the electric and magnetic fields outside the MDM ferrite disk. The analytical studies can display some fundamental features that are non-observable in the numerical results. While in numerical investigations, one cannot separate the ME fields from the external electromagnetic (EM) radiation, the present theoretical analysis allows clearly distinguish the eigen topological structure of the ME fields. Importantly, this ME-field structure gives evidence for certain phenomena that can be related to the Tellegen and bianisotropic coupling effects. We discuss the question whether the MDM ferrite disk can exhibit properties of the cross magnetoelectric polarizabilities. - Highlights: • We obtain analytically topological characteristics of the ME-field modes. • We take into account the influence of the edge regions of an open ferrite disk. • We obtain a “pure” structure of the electromagnetic fields outside the ferrite disk. • Analytical studies show features that are non-observable in the numerical results. • ME-field gives evidence for

  4. Microwave magnetoelectric fields: An analytical study of topological characteristics

    International Nuclear Information System (INIS)

    Joffe, R.; Shavit, R.; Kamenetskii, E.O.

    2015-01-01

    The near fields originated from a small quasi-two-dimensional ferrite disk with magnetic-dipolar-mode (MDM) oscillations are the fields with broken dual (electric-magnetic) symmetry. Numerical studies show that such fields – called the magnetoelectric (ME) fields – are distinguished by the power-flow vortices and helicity parameters (E.O. Kamenetskii, R. Joffe, R. Shavit, Phys. Rev. E 87 (2013) 023201). These numerical studies can well explain recent experimental results with MDM ferrite disks. In the present paper, we obtain analytically topological characteristics of the ME-field modes. For this purpose, we used a method of successive approximations. In the second approximation we take into account the influence of the edge regions of an open ferrite disk, which are excluded in the first-approximation solving of the magnetostatic (MS) spectral problem. Based on the analytical method, we obtain a “pure” structure of the electric and magnetic fields outside the MDM ferrite disk. The analytical studies can display some fundamental features that are non-observable in the numerical results. While in numerical investigations, one cannot separate the ME fields from the external electromagnetic (EM) radiation, the present theoretical analysis allows clearly distinguish the eigen topological structure of the ME fields. Importantly, this ME-field structure gives evidence for certain phenomena that can be related to the Tellegen and bianisotropic coupling effects. We discuss the question whether the MDM ferrite disk can exhibit properties of the cross magnetoelectric polarizabilities. - Highlights: • We obtain analytically topological characteristics of the ME-field modes. • We take into account the influence of the edge regions of an open ferrite disk. • We obtain a “pure” structure of the electromagnetic fields outside the ferrite disk. • Analytical studies show features that are non-observable in the numerical results. • ME-field gives evidence for

  5. A preliminary population study of alcove bog orchid (Platanthera zothecina) at Navajo National Monument, Arizona

    Science.gov (United States)

    Laura E. Hudson

    2001-01-01

    This study on Platanthera zothecina (alcove bog orchid) was initiated by the National Park Service after a recent threatened and endangered species survey at Navajo National Monument. It is listed as Category 2 (species of special concern) by the U.S. Fish and Wildlife Service, and Category 3 (likely to become endangered) by the Navajo Nation. Because P. zothecina is a...

  6. Pedagogy against the State: The Ban on Ethnic Studies in Arizona

    Science.gov (United States)

    Wanberg, Kyle

    2013-01-01

    Drawing on the traditions of critical pedagogy from Paulo Freire and Henry Giroux to recent critical research developed in the "Journal of Pedagogy," this study explores how a particular case of curriculum reform in the US is entangled with racial neoliberalism and paranoia.

  7. Nuclear Hybrid Energy Systems - Regional Studies. West Texas and Northeastern Arizona

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, Humberto E. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Chen, Jun [Idaho National Lab. (INL), Idaho Falls, ID (United States); Kim, Jong S. [Idaho National Lab. (INL), Idaho Falls, ID (United States); McKellar, Michael G. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Deason, Wesley R. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Vilim, Richard B. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Bragg-Sitton, Shannon M. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Boardman, Richard D. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-04-01

    The primary objective of this study is to conduct a preliminary dynamic analysis of two realistic hybrid energy systems (HES) including a nuclear reactor as the main baseload heat generator (denoted as nuclear HES or nuclear hybrid energy systems [NHES]) and to assess the local (e.g., HES owners) and system (e.g., the electric grid) benefits attainable by the application of NHES in scenarios with multiple commodity production and high penetration of renewable energy. It is performed for regional cases - not generic examples - based on available resources, existing infrastructure, and markets within the selected regions. This study also briefly addresses the computational capabilities developed to conduct such analyses, reviews technical gaps, and suggests some research paths forward.

  8. An analytical study of double bend achromat lattice

    Energy Technology Data Exchange (ETDEWEB)

    Fakhri, Ali Akbar, E-mail: fakhri@rrcat.gov.in; Kant, Pradeep; Singh, Gurnam; Ghodke, A. D. [Raja Ramanna Centre for Advanced Technology, Indore 452 013 (India)

    2015-03-15

    In a double bend achromat, Chasman-Green (CG) lattice represents the basic structure for low emittance synchrotron radiation sources. In the basic structure of CG lattice single focussing quadrupole (QF) magnet is used to form an achromat. In this paper, this CG lattice is discussed and an analytical relation is presented, showing the limitation of basic CG lattice to provide the theoretical minimum beam emittance in achromatic condition. To satisfy theoretical minimum beam emittance parameters, achromat having two, three, and four quadrupole structures is presented. In this structure, different arrangements of QF and defocusing quadruple (QD) are used. An analytical approach assuming quadrupoles as thin lenses has been followed for studying these structures. A study of Indus-2 lattice in which QF-QD-QF configuration in the achromat part has been adopted is also presented.

  9. An analytical study of double bend achromat lattice.

    Science.gov (United States)

    Fakhri, Ali Akbar; Kant, Pradeep; Singh, Gurnam; Ghodke, A D

    2015-03-01

    In a double bend achromat, Chasman-Green (CG) lattice represents the basic structure for low emittance synchrotron radiation sources. In the basic structure of CG lattice single focussing quadrupole (QF) magnet is used to form an achromat. In this paper, this CG lattice is discussed and an analytical relation is presented, showing the limitation of basic CG lattice to provide the theoretical minimum beam emittance in achromatic condition. To satisfy theoretical minimum beam emittance parameters, achromat having two, three, and four quadrupole structures is presented. In this structure, different arrangements of QF and defocusing quadruple (QD) are used. An analytical approach assuming quadrupoles as thin lenses has been followed for studying these structures. A study of Indus-2 lattice in which QF-QD-QF configuration in the achromat part has been adopted is also presented.

  10. An analytical study of double bend achromat lattice

    International Nuclear Information System (INIS)

    Fakhri, Ali Akbar; Kant, Pradeep; Singh, Gurnam; Ghodke, A. D.

    2015-01-01

    In a double bend achromat, Chasman-Green (CG) lattice represents the basic structure for low emittance synchrotron radiation sources. In the basic structure of CG lattice single focussing quadrupole (QF) magnet is used to form an achromat. In this paper, this CG lattice is discussed and an analytical relation is presented, showing the limitation of basic CG lattice to provide the theoretical minimum beam emittance in achromatic condition. To satisfy theoretical minimum beam emittance parameters, achromat having two, three, and four quadrupole structures is presented. In this structure, different arrangements of QF and defocusing quadruple (QD) are used. An analytical approach assuming quadrupoles as thin lenses has been followed for studying these structures. A study of Indus-2 lattice in which QF-QD-QF configuration in the achromat part has been adopted is also presented

  11. Construction QA/QC systems: comparative analysis

    International Nuclear Information System (INIS)

    Willenbrock, J.H.; Shepard, S.

    1980-01-01

    An analysis which compares the quality assurance/quality control (QA/QC) systems adopted in the highway, nuclear power plant, and U.S. Navy construction areas with the traditional quality control approach used in building construction is presented. Full participation and support by the owner as well as the contractor and AE firm are required if a QA/QC system is to succeed. Process quality control, acceptance testing and quality assurance responsibilities must be clearly defined in the contract documents. The owner must audit these responsibilities. A contractor quality control plan, indicating the tasks which will be performed and the fact that QA/QC personnel are independent of project time/cost pressures should be submitted for approval. The architect must develop realistic specifications which consider the natural variability of material. Acceptance criteria based on the random sampling technique should be used. 27 refs

  12. Dispersion of helically corrugated waveguides: Analytical, numerical, and experimental study

    International Nuclear Information System (INIS)

    Burt, G.; Ronald, K.; Young, A.R.; Phelps, A.D.R.; Cross, A.W.; Konoplev, I.V.; He, W.; Thomson, J.; Whyte, C.G.; Samsonov, S.V.; Denisov, G.G.; Bratman, V.L.

    2004-01-01

    Helically corrugated waveguides have recently been studied for use in various applications such as interaction regions in gyrotron traveling-wave tubes and gyrotron backward-wave oscillators and as a dispersive medium for passive microwave pulse compression. The paper presents a summary of various methods that can be used for analysis of the wave dispersion of such waveguides. The results obtained from an analytical approach, simulations with the three-dimensional numerical code MAGIC, and cold microwave measurements are analyzed and compared

  13. Ecosystem services valuation to support decisionmaking on public lands—A case study of the San Pedro River watershed, Arizona

    Science.gov (United States)

    Bagstad, Kenneth J.; Semmens, Darius; Winthrop, Rob; Jaworksi, Delilah; Larson, Joel

    2012-01-01

    This report details the findings of the Bureau of Land Management–U.S. Geological Survey Ecosystem Services Valuation Pilot Study. This project evaluated alternative methods and tools that quantify and value ecosystem services, and it assessed the tools’ readiness for use in the Bureau of Land Management decisionmaking process. We tested these tools on the San Pedro River watershed in northern Sonora, Mexico, and southeast Arizona. The study area includes the San Pedro Riparian National Conservation Area (managed by the Bureau of Land Management), which has been a focal point for conservation activities and scientific research in recent decades. We applied past site-specific primary valuation studies, value transfer, the Wildlife Habitat Benefits Estimation Toolkit, and the Integrated Valuation of Ecosystem Services and Tradeoffs (InVEST) and Artificial Intelligence for Ecosystem Services (ARIES) models to value locally important ecosystem services for the San Pedro River watershed—water, carbon, biodiversity, and cultural values. We tested these approaches on a series of scenarios to evaluate ecosystem service changes and the ability of the tools to accommodate scenarios. A suite of additional tools were either at too early a stage of development to run, were proprietary, or were place-specific tools inappropriate for application to the San Pedro River watershed. We described the strengths and weaknesses of these additional ecosystem service tools against a series of evaluative criteria related to their usefulness for Bureau of Land Management decisionmaking. Using these tools, we quantified gains or losses of ecosystem services under three categories of scenarios: urban growth, mesquite management, and water augmentation. These results quantify tradeoffs and could be useful for decisionmaking within Bureau of Land Management district or field offices. Results are accompanied by a relatively high level of uncertainty associated with model outputs, valuation

  14. Investigations of low qa discharges in the SINP tokamak

    Indian Academy of Sciences (India)

    Low edge safety factor discharges including very low qa (1 qa ... From fluctuation analysis of the external magnetic probe data it has been found that MHD ... To investigate the internal details of these discharges, an internal magnetic probe ...

  15. An analytical study on the thermal stress of mass concrete

    International Nuclear Information System (INIS)

    Yoshida, H.; Sawada, T.; Yamazaki, M.; Miyashita, T.; Morikawa, H.; Hayami, Y.; Shibata, K.

    1983-01-01

    The thermal stress in mass concrete occurs as a result of the effect associated with the heat of hydration of the cement. Sometimes, the excessive stresses cause the cracking or other tensile failure in concrete. Therefore it is becoming necessary in the design and construction of mass concrete to predict the thermal stress. The thermal stress analysis of mass concrete requires to take account of the dependence of the elastic modulus on the age of concrete as well as the stress relaxation by creep effect. The studies of those phenomena and the analytical methods have been reported so far. The paper presents the analytical method and discusses its reliability through the application of the method to the actual structure, measuring the temperatures and the thermal stresses. The method is the time dependent thermal stress analysis based on the finite element method, which takes account of creep effect, the aging of concrete and the effect of temperature variation in time. (orig./HP)

  16. A Web-Based Geovisual Analytical System for Climate Studies

    Directory of Open Access Journals (Sweden)

    Zhenlong Li

    2012-12-01

    Full Text Available Climate studies involve petabytes of spatiotemporal datasets that are produced and archived at distributed computing resources. Scientists need an intuitive and convenient tool to explore the distributed spatiotemporal data. Geovisual analytical tools have the potential to provide such an intuitive and convenient method for scientists to access climate data, discover the relationships between various climate parameters, and communicate the results across different research communities. However, implementing a geovisual analytical tool for complex climate data in a distributed environment poses several challenges. This paper reports our research and development of a web-based geovisual analytical system to support the analysis of climate data generated by climate model. Using the ModelE developed by the NASA Goddard Institute for Space Studies (GISS as an example, we demonstrate that the system is able to (1 manage large volume datasets over the Internet; (2 visualize 2D/3D/4D spatiotemporal data; (3 broker various spatiotemporal statistical analyses for climate research; and (4 support interactive data analysis and knowledge discovery. This research also provides an example for managing, disseminating, and analyzing Big Data in the 21st century.

  17. Transformational Leadership and Teacher Motivation in Southwestern Arizona High Schools

    Science.gov (United States)

    Reynolds, Catherine L.

    2009-01-01

    The purpose of this study was to explore the relationship between transformational leadership and teacher motivation in Southwestern Arizona high schools. Teachers in a school district in Southwestern Arizona comprised of high schools were surveyed using two instruments, Leithwood and Jantzi's (1998) The Leadership and Management of Schools in…

  18. The impact of Arizona Highways Magazine on tourism.

    Science.gov (United States)

    2012-03-01

    The purpose of this study was to: 1) examine the effect of Arizona Highways Magazine (AHM) on tourism, 2) determine trip : characteristics of AHM subscribers traveling in Arizona, and 3) calculate a benefit/cost ratio for AHM based on the : magazine...

  19. Innovations in Arizona's Accountability Policies and Frameworks for Alternative Schools

    Science.gov (United States)

    Schlessman, Amy

    2014-01-01

    This study presents Arizona's innovations in academic accountability policy and academic accountability frameworks for alternative schools. A timeline of statutes and regulations including the State Board of Education approved alternative school definition provides Arizona's context for alternative school accountability policy and frameworks.…

  20. Seamless Digital Environment - Plan for Data Analytics Use Case Study

    International Nuclear Information System (INIS)

    Oxstrand, Johanna Helene; Bly, Aaron Douglas

    2016-01-01

    The U.S Department of Energy Light Water Reactor Sustainability (LWRS) Program initiated research in to what is needed in order to provide a roadmap or model for Nuclear Power Plants to reference when building an architecture that can support the growing data supply and demand flowing through their networks. The Digital Architecture project published report Digital Architecture Planning Model (Oxstrand et. al, 2016) discusses things to consider when building an architecture to support the increasing needs and demands of data throughout the plant. Once the plant is able to support the data demands it still needs to be able to provide the data in an easy, quick and reliable method. A common method is to create a ''one stop shop'' application that a user can go to get all the data they need. The creation of this leads to the need of creating a Seamless Digital Environment (SDE) to integrate all the ''siloed'' data. An SDE is the desired perception that should be presented to users by gathering the data from any data source (e.g., legacy applications and work management systems) without effort by the user. The goal for FY16 was to complete a feasibility study for data mining and analytics for employing information from computer-based procedures enabled technologies for use in developing improved business analytics. The research team collaborated with multiple organizations to identify use cases or scenarios, which could be beneficial to investigate in a feasibility study. Many interesting potential use cases were identified throughout the FY16 activity. Unfortunately, due to factors out of the research team's control, none of the studies were initiated this year. However, the insights gained and the relationships built with both PVNGS and NextAxiom will be valuable when moving forward with future research. During the 2016 annual Nuclear Information Technology Strategic Leadership (NITSL) group meeting it was identified would be very beneficial to the industry to

  1. Minority Student Progress Report 2009: A Snapshot of Arizona's Educational Achievement

    Science.gov (United States)

    Morel-Seytoux, Sylvie

    2009-01-01

    The Arizona Minority Education Policy Analysis Center (AMEPAC) is a policy center of the Arizona Commission for Postsecondary Education. AMEPAC's mission is to stimulate, through studies, statewide discussion, and debate, constructive improvement of Arizona minority students' early awareness, access, and achievement throughout the educational…

  2. Analytical and Experimental Study of Residual Stresses in CFRP

    Directory of Open Access Journals (Sweden)

    Chia-Chin Chiang

    2013-01-01

    Full Text Available Fiber Bragg Grating sensors (FBGs have been utilized in various engineering and photoelectric fields because of their good environment tolerance. In this research, residual stresses of carbon fiber reinforced polymer composites (CFRP were studied using both experimental and analytical approach. The FBGs were embedded inside middle layers of CFRP to study the formation of residual stress during curing process. Finite element analysis was performed using ABAQUS software to simulate the CFRP curing process. Both experimental and simulation results showed that the residual stress appeared during cooling process and the residual stresses could be released when the CFRP was machined to a different shape.

  3. IMRT QA: Selecting gamma criteria based on error detection sensitivity

    Energy Technology Data Exchange (ETDEWEB)

    Steers, Jennifer M. [Department of Radiation Oncology, Cedars-Sinai Medical Center, Los Angeles, California 90048 and Physics and Biology in Medicine IDP, David Geffen School of Medicine, University of California, Los Angeles, Los Angeles, California 90095 (United States); Fraass, Benedick A., E-mail: benedick.fraass@cshs.org [Department of Radiation Oncology, Cedars-Sinai Medical Center, Los Angeles, California 90048 (United States)

    2016-04-15

    Purpose: The gamma comparison is widely used to evaluate the agreement between measurements and treatment planning system calculations in patient-specific intensity modulated radiation therapy (IMRT) quality assurance (QA). However, recent publications have raised concerns about the lack of sensitivity when employing commonly used gamma criteria. Understanding the actual sensitivity of a wide range of different gamma criteria may allow the definition of more meaningful gamma criteria and tolerance limits in IMRT QA. We present a method that allows the quantitative determination of gamma criteria sensitivity to induced errors which can be applied to any unique combination of device, delivery technique, and software utilized in a specific clinic. Methods: A total of 21 DMLC IMRT QA measurements (ArcCHECK®, Sun Nuclear) were compared to QA plan calculations with induced errors. Three scenarios were studied: MU errors, multi-leaf collimator (MLC) errors, and the sensitivity of the gamma comparison to changes in penumbra width. Gamma comparisons were performed between measurements and error-induced calculations using a wide range of gamma criteria, resulting in a total of over 20 000 gamma comparisons. Gamma passing rates for each error class and case were graphed against error magnitude to create error curves in order to represent the range of missed errors in routine IMRT QA using 36 different gamma criteria. Results: This study demonstrates that systematic errors and case-specific errors can be detected by the error curve analysis. Depending on the location of the error curve peak (e.g., not centered about zero), 3%/3 mm threshold = 10% at 90% pixels passing may miss errors as large as 15% MU errors and ±1 cm random MLC errors for some cases. As the dose threshold parameter was increased for a given %Diff/distance-to-agreement (DTA) setting, error sensitivity was increased by up to a factor of two for select cases. This increased sensitivity with increasing dose

  4. National uranium resource evaluation: Williams quadrangle, Arizona

    International Nuclear Information System (INIS)

    O'Neill, A.J.; Nystrom, R.J.; Thiede, D.S.

    1981-03-01

    Geologic environments of the Williams Quadrangle, Arizona, were evaluated for uranium favorability by means of literature research, uranium-occurrence investigation and other surface studies, subsurface studies, aerial radiometric data, hydrogeochemical data, and rock-sample analytic data. Favorability criteria are those of the National Uranium Resource Evaluation program. Three geologic environments are favorable for uranium: the Tertiary fluvial rocks of the Colorado Plateau where they unconformably overlie impermeable bed rock (for channel-controlled peneconcordant deposits); collapse breccia pipes in Paleozoic strata of the Colorado Plateau (for vein-type deposits in sedimentary rocks); and Precambrian crystalline rocks of the Hualapai, Peacock, and Aquarius Mountains, and Cottonwood and Grand Wash Cliffs (for magmatic-hydrothermal deposits). Unfavorable geologic environments are: Tertiary and Quaternary volcanic rocks, Tertiary and Quaternary sedimentary rocks of the Colorado Plateau, nearly all Paleozoic and Mesozoic sedimentary rocks, and the Precambrian-Cambrian unconformity of the Grand Wash Cliffs area. Tertiary rocks in Cenozoic basins and Precambrian crystalline rocks in the Grand Canyon region and in parts of the Aquarius Mountains and Cottonwood and Grand Wash Cliffs are unevaluated

  5. Basic concept of QA for advanced technologies

    International Nuclear Information System (INIS)

    Mijnheer, Ben

    2008-01-01

    The lecture was structured as follows: (1) Rationale for accurate dose determination; (2) Existing recommendations and guidance; (3) Challenges within the current QA paradigm; (4) New paradigm adopted by AAPM TG 100; and (5) Application of new paradigm to IMRT. Attention was paid, i.a., to major accidents in radiotherapy such as Epinal-1. (P.A.)

  6. Radiotherapy QA of the DAHANCA 19 protocol

    DEFF Research Database (Denmark)

    Samsøe, E.; Andersen, E.; Hansen, C. R.

    2015-01-01

    Purpose/Objective: It has been demonstrated that nonadherence to protocol-specified radiotherapy (RT) requirements is associated with reduced survival, local control and potentially increased toxicity [1]. Thus, quality assurance (QA) of RT is important when evaluating the results of clinical...

  7. March 2014 Arizona thoracic society notes

    Directory of Open Access Journals (Sweden)

    Robbins RA

    2014-04-01

    Full Text Available No abstract available. Article truncated after 150 words. The March 2014 Arizona Thoracic Society meeting was a special meeting. In conjunction with the Valley Fever Center for Excellence and the Arizona Respiratory Center the Eighteenth Annual Farness Lecture was held in the Sonntag Pavilion at St. Joseph's Hospital at 6 PM on Friday, April 4, 2014. The guest speaker was Antonio "Tony" Catanzaro, MD from the University of California San Diego and current president of the Cocci Study Group. There were 57 in attendance representing the pulmonary, critical care, sleep, and infectious disease communities. After opening remarks by Arizona Thoracic Society president, Lewis Wesselius (a former fellow under Dr. Catanzaro at UCSD, John Galgiani, director of the Valley Fever Center for Excellence, gave a brief history of the Farness lecture before introducing Dr. Catanzaro. The lecture is named for Orin J. Farness, a Tucson physician, who was the first to report culture positive coccidioidomycosis (cocci or Valley Fever. ...

  8. The Virtual Arizona Experience

    Science.gov (United States)

    Allison, M. L.; Davis, R.; Conway, F. M.; Bellasai, R.

    2012-12-01

    To commemorate the once-in-a-lifetime event of Arizona's hundredth birthday, the Centennial Commission and the Governor of Arizona envisioned a museum and companion website that would capture the state's history, celebrate its people, and embrace its future. Working with world-renowned museum designers, the state began to seek ideas from across Arizona to create plans for a journey of discovery through science and the humanities. The museum would introduce visitors to some of the people who nurtured the state through its early years and others who are innovating its tomorrows. Showcases would include the resources and experiences that shaped the state's history and are transforming its present day, highlighting the ingenuity that tamed the wild frontier and is envisioning Arizona's next frontiers through science and technology. The Arizona Experience (www.arizonaexperience.org) was initially intended to serve as the web presence for the physical museum, but as delays occurred with the physical museum, the site has quickly developed an identify of its own as an interactive, multimedia experience, reaching a wider audience with functions that would be difficult or expensive to produce in a museum. As leaders in scientific and technological innovation in the state, the Arizona Geological Survey was tasked with designing and creating the Arizona Experience site. The general themes remain the same; however, the site has added content and applications that are better suited to the online environment in order to create a rich, dynamic supplement to a physical museum experience. The website offers the features and displays of the future museum with the interactive nature and learning environment of the web. This provides an encyclopedic overview of the State of Arizona by subject matter experts in a manner that is free and open to the public and erases socio-economic, political, and physical boundaries. Over the Centennial Year of 2012 the site will release a new theme and

  9. Dispersant testing : a study on analytical test procedures

    International Nuclear Information System (INIS)

    Fingas, M.F.; Fieldhouse, B.; Wang, Z.; Environment Canada, Ottawa, ON

    2004-01-01

    Crude oil is a complex mixture of hydrocarbons, ranging from small, volatile compounds to very large, non-volatile compounds. Analysis of the dispersed oil is crucial. This paper described Environment Canada's ongoing studies on various traits of dispersants. In particular, it describes small studies related to dispersant effectiveness and methods to improve analytical procedures. The study also re-evaluated the analytical procedure for the Swirling Flask Test, which is now part of the ASTM standard procedure. There are new and improved methods for analyzing oil-in-water using gas chromatography (GC). The methods could be further enhanced by integrating the entire chromatogram rather than just peaks. This would result in a decrease in maximum variation from 5 per cent to about 2 per cent. For oil-dispersant studies, the surfactant-dispersed oil hydrocarbons consist of two parts: GC-resolved hydrocarbons and GC-unresolved hydrocarbons. This study also tested a second feature of the Swirling Flask Test in which the side spout was tested and compared with a new vessel with a septum port instead of a side spout. This decreased the variability as well as the energy and mixing in the vessel. Rather than being a variation of the Swirling Flask Test, it was suggested that a spoutless vessel might be considered as a completely separate test. 7 refs., 2 tabs., 4 figs

  10. Analytical study of zirconium and hafnium α-hydroxy carboxylates

    International Nuclear Information System (INIS)

    Terra, V.R.

    1991-01-01

    The analytical study of zirconium and hafnium α-hydroxy carboxylates was described. For this purpose dl-mandelic, dl-p-bromo mandelic, dl-2-naphthyl glycolic, and benzilic acids were prepared. These were used in conjunction with glycolic, dl-lactic, dl-2-hydroxy isovaleric, dl-2-hydroxy hexanoic, and dl-2-hydroxy dodecanoic acids in order to synthesize the zirconium(IV) and hafnium(IV) tetrakis(α-hydroxy carboxylates). The compounds were characterized by melting point determination, infrared spectroscopy, thermogravimetric analysis, calcination to oxides and X-ray diffractometry by the powder method. (C.G.C)

  11. Meta-Analytical Studies in Transport Economics. Methodology and Applications

    Energy Technology Data Exchange (ETDEWEB)

    Brons, M.R.E.

    2006-05-18

    Vast increases in the external costs of transport in the late twentieth century have caused national and international governmental bodies to worry about the sustainability of their transport systems. In this thesis we use meta-analysis as a research method to study various topics in transport economics that are relevant for sustainable transport policymaking. Meta-analysis is a research methodology that is based on the quantitative summarisation of a body of previously documented empirical evidence. In several fields of economic, meta-analysis has become a well-accepted research tool. Despite the appeal of the meta-analytical approach, there are methodological difficulties that need to be acknowledged. We study a specific methodological problem which is common in meta-analysis in economics, viz., within-study dependence caused by multiple sampling techniques. By means of Monte Carlo analysis we investigate the effect of such dependence on the performance of various multivariate estimators. In the applied part of the thesis we use and develop meta-analytical techniques to study the empirical variation in indicators of the price sensitivity of demand for aviation transport, the price sensitivity of demand for gasoline, the efficiency of urban public transport and the valuation of the external costs of noise from rail transport. We focus on the estimation of mean values for these indicators and on the identification of the impact of conditioning factors.

  12. Minimum requirements on a QA program in radiation oncology

    International Nuclear Information System (INIS)

    Almond, P.R.

    1996-01-01

    In April, 1994, the American Association of Physicists in Medicine published a ''Comprehensive QA for radiation oncology:'' a report of the AAPM Radiation Therapy Committee. This is a comprehensive QA program which is likely to become the standard for such programs in the United States. The program stresses the interdisciplinary nature of QA in radiation oncology involving the radiation oncologists, the radiotherapy technologies (radiographers), dosimetrists, and accelerator engineers, as well as the medical physicists. This paper describes a comprehensive quality assurance program with the main emphasis on the quality assurance in radiation therapy using a linear accelerator. The paper deals with QA for a linear accelerator and simulator and QA for treatment planning computers. Next the treatment planning process and QA for individual patients is described. The main features of this report, which should apply to QA programs in any country, emphasizes the responsibilities of the medical physicist. (author). 7 refs, 9 tabs

  13. Minimum requirements on a QA program in radiation oncology

    Energy Technology Data Exchange (ETDEWEB)

    Almond, P R [Louisville Univ., Louisville, KY (United States). J.G. Brown Cancer Center

    1996-08-01

    In April, 1994, the American Association of Physicists in Medicine published a ``Comprehensive QA for radiation oncology:`` a report of the AAPM Radiation Therapy Committee. This is a comprehensive QA program which is likely to become the standard for such programs in the United States. The program stresses the interdisciplinary nature of QA in radiation oncology involving the radiation oncologists, the radiotherapy technologies (radiographers), dosimetrists, and accelerator engineers, as well as the medical physicists. This paper describes a comprehensive quality assurance program with the main emphasis on the quality assurance in radiation therapy using a linear accelerator. The paper deals with QA for a linear accelerator and simulator and QA for treatment planning computers. Next the treatment planning process and QA for individual patients is described. The main features of this report, which should apply to QA programs in any country, emphasizes the responsibilities of the medical physicist. (author). 7 refs, 9 tabs.

  14. An Analytical Study of Prostate-Specific Antigen Dynamics.

    Science.gov (United States)

    Esteban, Ernesto P; Deliz, Giovanni; Rivera-Rodriguez, Jaileen; Laureano, Stephanie M

    2016-01-01

    The purpose of this research is to carry out a quantitative study of prostate-specific antigen dynamics for patients with prostatic diseases, such as benign prostatic hyperplasia (BPH) and localized prostate cancer (LPC). The proposed PSA mathematical model was implemented using clinical data of 218 Japanese patients with histological proven BPH and 147 Japanese patients with LPC (stages T2a and T2b). For prostatic diseases (BPH and LPC) a nonlinear equation was obtained and solved in a close form to predict PSA progression with patients' age. The general solution describes PSA dynamics for patients with both diseases LPC and BPH. Particular solutions allow studying PSA dynamics for patients with BPH or LPC. Analytical solutions have been obtained and solved in a close form to develop nomograms for a better understanding of PSA dynamics in patients with BPH and LPC. This study may be useful to improve the diagnostic and prognosis of prostatic diseases.

  15. Trade in and Valuation of Virtual Water Impacts in a City: A Case Study Of Flagstaff, Arizona

    Science.gov (United States)

    Rushforth, R.; Ruddell, B. L.

    2013-12-01

    An increasingly intense component of the global coupled natural and human system (CNH) is the economic trade of various types of resources and the outsourcing of resource impacts between geographically distant economic systems. The human economy's trade arrangements allow specific localities, especially cities, to exceed spatially local resource stock sustainability and footprint constraints, as evidenced in the urban metabolism literature. Each movement or trade of a resource along a network is associated with an embedded or 'virtual' exchange of indirect impacts on the inputs to the production process. The networked trade of embedded resources, therefore, is an essential human adaptation to resource limitations. Using the Embedded Resource Impact Accounting (ERA) framework, we examine the network of embedded water flows created through the trade of goods and services and economic development in Flagstaff, Arizona, and associate these flows with the creation of value in sectors of the economy

  16. Sky View Factors from Synthetic Fisheye Photos for Thermal Comfort Routing—A Case Study in Phoenix, Arizona

    Directory of Open Access Journals (Sweden)

    Ariane Middel

    2017-03-01

    Full Text Available The Sky View Factor (SVF is a dimension-reduced representation of urban form and one of the major variables in radiation models that estimate outdoor thermal comfort. Common ways of retrieving SVFs in urban environments include capturing fisheye photographs or creating a digital 3D city or elevation model of the environment. Such techniques have previously been limited due to a lack of imagery or lack of full scale detailed models of urban areas. We developed a web based tool that automatically generates synthetic hemispherical fisheye views from Google Earth at arbitrary spatial resolution and calculates the corresponding SVFs through equiangular projection. SVF results were validated using Google Maps Street View and compared to results from other SVF calculation tools. We generated 5-meter resolution SVF maps for two neighborhoods in Phoenix, Arizona to illustrate fine-scale variations of intra-urban horizon limitations due to urban form and vegetation. To demonstrate the utility of our synthetic fisheye approach for heat stress applications, we automated a radiation model to generate outdoor thermal comfort maps for Arizona State University’s Tempe campus for a hot summer day using synthetic fisheye photos and on-site meteorological data. Model output was tested against mobile transect measurements of the six-directional radiant flux density. Based on the thermal comfort maps, we implemented a pedestrian routing algorithm that is optimized for distance and thermal comfort preferences. Our synthetic fisheye approach can help planners assess urban design and tree planting strategies to maximize thermal comfort outcomes and can support heat hazard mitigation in urban areas.

  17. Kaljujooniste keskus Arizonas / Andres Kurg

    Index Scriptorium Estoniae

    Kurg, Andres, 1975-

    1998-01-01

    Arhitekt William Bruderi projekteeritud kaljujooniste uurimis- ja eksponeerimiskeskus Phoenixis, Arizonas säilitab kivijooniseid, mille autoriteks olid sealset piirkonda kuni 16. sajandini asustanud hohokamid

  18. Resonant particle production during inflation: a full analytical study

    Energy Technology Data Exchange (ETDEWEB)

    Pearce, Lauren; Peloso, Marco [School of Physics and Astronomy, University of Minnesota, 116 Church Street S.E., Minneapolis, MN 55455 (United States); Sorbo, Lorenzo, E-mail: lpearce@physics.umn.edu, E-mail: peloso@physics.umn.edu, E-mail: sorbo@physics.umass.edu [Amherst Center for Fundamental Interactions, Department of Physics, University of Massachusetts, 1126 Lederle Graduate Research Tower (LGRT), Amherst, MA 01003 (United States)

    2017-05-01

    We revisit the study of the phenomenology associated to a burst of particle production of a field whose mass is controlled by the inflaton field and vanishes at one given instance during inflation. This generates a bump in the correlators of the primordial scalar curvature. We provide a unified formalism to compute various effects that have been obtained in the literature and confirm that the dominant effects are due to the rescattering of the produced particles on the inflaton condensate. We improve over existing results (based on numerical fits) by providing exact analytic expressions for the shape and height of the bump, both in the power spectrum and the equilateral bispectrum. We then study the regime of validity of the perturbative computations of this signature. Finally, we extend these computations to the case of a burst of particle production in a sector coupled only gravitationally to the inflaton.

  19. Marginalizing TESOL: Preservice Teacher Training in Arizona

    Science.gov (United States)

    Diniz de Figueiredo, Eduardo H.; Hammill, Matthew J.; Fredricks, Daisy E.

    2011-01-01

    This pilot study investigated the attitudes of preservice teachers at a major university in Arizona concerning the Structured English Immersion (SEI) program that is now being used with English language learners (ELLs). Using a survey, we examined how preservice teachers feel about potentially working with ELLs in this SEI context. We focused on…

  20. Turnover of Public School Superintendents in Arizona

    Science.gov (United States)

    Meyer, Joyce Ntsoaki

    2013-01-01

    This study used a descriptive qualitative design utilizing a phenomenological approach to determine and examine the reasons behind the voluntary or involuntary turnover of Arizona school superintendents. Open-ended questions were used to interview five superintendents who had left their districts between 2008 and 2013 about their perceptions on…

  1. Beam dynamics of mixed high intensity highly charged ion Beams in the Q/A selector

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, X.H., E-mail: zhangxiaohu@impcas.ac.cn [Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Yuan, Y.J.; Yin, X.J.; Qian, C.; Sun, L.T. [Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Du, H.; Li, Z.S.; Qiao, J.; Wang, K.D. [Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Zhao, H.W.; Xia, J.W. [Institute of Modern Physics, Chinese Academy of Sciences, Lanzhou 730000 (China)

    2017-06-11

    Electron cyclotron resonance (ECR) ion sources are widely used in heavy ion accelerators for their advantages in producing high quality intense beams of highly charged ions. However, it exists challenges in the design of the Q/A selection systems for mixed high intensity ion beams to reach sufficient Q/A resolution while controlling the beam emittance growth. Moreover, as the emittance of beam from ECR ion sources is coupled, the matching of phase space to post accelerator, for a wide range of ion beam species with different intensities, should be carefully studied. In this paper, the simulation and experimental results of the Q/A selection system at the LECR4 platform are shown. The formation of hollow cross section heavy ion beam at the end of the Q/A selector is revealed. A reasonable interpretation has been proposed, a modified design of the Q/A selection system has been committed for HIRFL-SSC linac injector. The features of the new design including beam simulations and experiment results are also presented.

  2. Analytic study of the Migdal-Kadanoff recursion formula

    International Nuclear Information System (INIS)

    Ito, K.R.

    1984-01-01

    After proposing lattice gauge field models in which the Migdal renormalization group recursion formulas are exact, we study the recursion formulas analytically. If D is less than 4, it is shown that the effective actions of D-dimensional U(1) lattice gauge models are uniformly driven to the high temperature region no matter how low the initial temperature is. If the initial temperature is large enough, this holds for any D and gauge group G. These are also the cases for the recursion formulas of Kadanoff type. It turns out, however, that the string tension for D=3 obtained by these methods is rather big compared with the one already obtained by Mack, Goepfert and by the present author. The reason is clarified. (orig.)

  3. Analytical study plan: Shielded Cells batch 1 campaign; Revision 1

    International Nuclear Information System (INIS)

    Bibler, N.E.; Ha, B.C.; Hay, M.S.; Ferrara, D.M.; Andrews, M.K.

    1993-01-01

    Radioactive operations in the Defense Waste Processing Facility (DWPF) will require that the Savannah River Technology Center (SRTC) perform analyses and special studies with actual Savannah River Site (SRS) high-level waste sludge. SRS Tank 42 and Tank 51 will comprise the first batch of sludge to be processed in the DWPF. Approximately 25 liters of sludge from each of these tanks will be characterized and processed in the Shielded Cells of SRTC. During the campaign, processes will include sludge characterization, sludge washing, rheology determination, mixing, hydrogen evolution, feed preparation, and vitrification of the waste. To complete the campaign, the glass will be characterized to determine its durability and crystallinity. This document describes the types of samples that will be produced, the sampling schedule and analyses required, and the methods for sample and analytical control

  4. Analytic study of nonperturbative solutions in open string field theory

    International Nuclear Information System (INIS)

    Bars, I.; Kishimoto, I.; Matsuo, Y.

    2003-01-01

    We propose an analytic framework to study the nonperturbative solutions of Witten's open string field theory. The method is based on the Moyal star formulation where the kinetic term can be split into two parts. The first one describes the spectrum of two identical half strings which are independent from each other. The second one, which we call midpoint correction, shifts the half string spectrum to that of the standard open string. We show that the nonlinear equation of motion of string field theory is exactly solvable at zeroth order in the midpoint correction. An infinite number of solutions are classified in terms of projection operators. Among them, there exists only one stable solution which is identical to the standard butterfly state. We include the effect of the midpoint correction around each exact zeroth order solution as a perturbation expansion which can be formally summed to the complete exact solution

  5. Data from synoptic water-quality studies on the Colorado River in the Grand Canyon, Arizona, November 1990 and June 1991

    Science.gov (United States)

    Taylor, Howard E.; Peart, D.B.; Antweiler, Ronald C.; Brinton, T.I.; Campbell, W.L.; Barbarino, J.R.; Roth, D.A.; Hart, R.J.; Averett, R.C.

    1996-01-01

    Two water-quality synoptic studies were made on the Colorado River in the Grand Canyon, Arizona. Field measurements and the collection of water samples for laboratory analysis were made at 10 mainstem and 6 tributary sites every 6 hours for a 48-hour period on November 5-6, 1990, and again on June 18-20, 1991. Field measurements included discharge, alkalinity, water temperature, light penetration, pH, specific conductance, and dissolved oxygen. Water samples were collected for the laboratory analysis of major and minor ions (calcium, magnesium, sodium, potassium, strontium, chloride, sulfate, silica as SiO2), trace elements (aluminum, arsenic, boron, barium, beryllium, cadmium, cobalt, chromium, copper, iron, lead, lithium, manganese, molybdenum, nickel, selenium, thallium, uranium, vanadium and zinc), and nutrients (phosphate, nitrate, ammonium, nitrite, total dissolved nitrogen, total dissolved phosphorus and dissolved organic carbon). Biological measurements included drift (benthic invertebrates and detrital material), and benthic invertebrates from the river bottom.

  6. Understanding Business Analytics Success and Impact: A Qualitative Study

    Science.gov (United States)

    Parks, Rachida F.; Thambusamy, Ravi

    2017-01-01

    Business analytics is believed to be a huge boon for organizations since it helps offer timely insights over the competition, helps optimize business processes, and helps generate growth and innovation opportunities. As organizations embark on their business analytics initiatives, many strategic questions, such as how to operationalize business…

  7. Retrospective analysis of 'gamma distribution' based IMRT QA criteria

    International Nuclear Information System (INIS)

    Wen, C.; Chappell, R.A.

    2010-01-01

    Full text: IMRT has been implemented into clinical practice at Royal Hobart Hospital (RHH) since mid 2006 for treating patients with Head and Neck (H and N) or prostate tumours. A local quality assurance (QA) acceptance criteria based on 'gamma distribution' for approving IMRT plan was developed and implemented in early 2007. A retrospective analysis of such criteria over 194 clinical cases will be presented. The RHH IMRT criteria was established with assumption that gamma distribution obtained through inter-comparison of 2 D dose maps between planned and delivered was governed by a positive-hail' normal distribution. A commercial system-MapCheck was used for 2 D dose map comparison with a built-in gamma analysis tool. Gamma distribution histogram was generated and recorded for all cases. By retrospectively analysing those distributions using curve fitting technique, a statistical gamma distribution can be obtained and evaluated. This analytical result can be used for future IMRT planing and treatment delivery. The analyses indicate that gamma distribution obtained through MapCheckTM is well under the normal distribution, particularly for prostate cases. The applied pass/fail criteria is not overly sensitive to identify 'false fails' but can be further tighten-up for smaller field while for larger field found in both H and N and prostate cases, the criteria was correctly applied. Non-uniform distribution of detectors in MapCheck and experience level of planners are two major factors to variation in gamma distribution among clinical cases. This criteria derived from clinical statistics is superior and more accurate than single-valued criteria for lMRT QA acceptance procedure. (author)

  8. Integrated solid waste management of Scottsdale, Arizona

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-01

    The subject document reports the results of an in-depth investigation of the fiscal year 1992 cost of the city of Scottsdale, Arizona, integrated municipal solid waste management (IMSWM) system, the energy consumed to operate the system, and the environmental performance requirements for each of the system`s waste-processing and disposal facilities. The document reports actual data from records kept by participants. Every effort was made to minimize the use of assumptions, and no attempt is made to interpret the data reported. Analytical approaches are documented so that interested analysts may per-form manipulation or further analysis of the data. As such, the report is a reference document for municipal solid waste (MSW) management professionals who are interested in the actual costs and energy consumption, for a 1-year period, of an operating IMSWM system. The report is organized into two main parts. The first part is the executive summary and case study portion of the report. The executive summary provides a basic description of the study area and selected economic and energy information. Within the case study are detailed descriptions of each component operating during the study period; the quantities of solid waste collected, processed, and marketed within the study boundaries; the cost of MSW in Scottsdale; an energy usage analysis; a review of federal, state, and local environmental requirement compliance; a reference section; and a glossary of terms. The second part of the report focuses on a more detailed discourse on the above topics. In addition, the methodology used to determine the economic costs and energy consumption of the system components is found in the second portion of this report. The methodology created for this project will be helpful for those professionals who wish to break out the costs of their own integrated systems.

  9. Experimental and analytical study on thermoelectric self cooling of devices

    International Nuclear Information System (INIS)

    Martinez, A.; Astrain, D.; Rodriguez, A.

    2011-01-01

    This paper presents and studies the novel concept of thermoelectric self cooling, which can be introduced as the cooling and temperature control of a device using thermoelectric technology without electricity consumption. For this study, it is designed a device endowed with an internal heat source. Subsequently, a commonly used cooling system is attached to the device and the thermal performance is statistically assessed. Afterwards, it is developed and studied a thermoelectric self cooling system appropriate for the device. Experimental and analytical results show that the thermal resistance between the heat source and the environment reduced by 25-30% when the thermoelectric self cooling system is installed, and indicates the promising applicability of this technology to devices that generate large amounts of heat, such as electrical power converters, transformers and control systems. Likewise, it was statistically proved that the thermoelectric self cooling system leads to significant reductions in the temperature difference between the heat source and the environment, and, what is more, this reduction increases as the heat flow generated by the heat source increases, which makes evident the fact that thermoelectric self cooling systems work as temperature controllers. -- Highlights: → Novel concept of thermoelectric self cooling is presented and studied. → No extra electricity is needed. → Thermal resistance between the heat source and the environment reduces by 25-30%. → Increasing reduction in temperature difference between heat source and environment. → Great applicability to any device that generates heat and must be cooled.

  10. Conventional patient specific IMRT QA and 3DVH verification of dose distribution for helical tomotherapy

    International Nuclear Information System (INIS)

    Sharma, Prabhat Krishna; Joshi, Kishore; Epili, D.; Gavake, Umesh; Paul, Siji; Reena, Ph.; Jamema, S.V.

    2016-01-01

    In recent years, patient-specific IMRT QA has transitioned from point dose measurements by ion chambers to films to 2D array measurements. 3DVH software has taken this transition a step further by estimating the 3D dose delivered to the patient volume from 2D diode measurements using a planned dose perturbation (PDP) algorithm. This algorithm was developed to determine, if the conventional IMRT QA though sensitive at detecting errors, has any predictive power in detecting dose errors of clinical significance related to dose to the target volume and organs at risk (OAR). The aim of this study is to compare the conventional IMRT patient specific QA and 3DVH dose distribution for patients treated with helical tomotherapy (HT)

  11. The assessment report of QA program through the analysis of quality trend in 1994

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Yung Se; Hong, Kyung Sik; Park, Sang Pil; Park, Kun Woo [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1995-04-01

    Effectiveness and adequacy of KAERI Qualify Assurance Program is assessed through the analysis of quality trend. As a result of assessment, Quality Assurance System for each project has reached the stage of stabilization, and especially, significant improvement of the conformance to QA procedure, the control of QA Records and documents and the inspiration of quality mind for the job has been made. However, some problems discovered in this trend analysis, ie, improvement of efficiency of quality training and economies of design verification system, are required to take preventive actions and consider appropriate measures. In the future, QA is expected to be a support to assurance of nuclear safety and development of advanced technology by making it possible to establish the best quality system suitable for our situation, based on the assessment method for quality assurance program presented in this study. 5 figs., 30 tabs. (Author).

  12. The assessment report of QA program through the analysis of quality trend in 1994

    International Nuclear Information System (INIS)

    Kim, Yung Se; Hong, Kyung Sik; Park, Sang Pil; Park, Kun Woo

    1995-04-01

    Effectiveness and adequacy of KAERI Qualify Assurance Program is assessed through the analysis of quality trend. As a result of assessment, Quality Assurance System for each project has reached the stage of stabilization, and especially, significant improvement of the conformance to QA procedure, the control of QA Records and documents and the inspiration of quality mind for the job has been made. However, some problems discovered in this trend analysis, ie, improvement of efficiency of quality training and economies of design verification system, are required to take preventive actions and consider appropriate measures. In the future, QA is expected to be a support to assurance of nuclear safety and development of advanced technology by making it possible to establish the best quality system suitable for our situation, based on the assessment method for quality assurance program presented in this study. 5 figs., 30 tabs. (Author)

  13. Analysis of QA audit checklist for equipment suppliers

    International Nuclear Information System (INIS)

    Tian Xuehang

    2012-01-01

    Eleven aspects during the equipment manufacturing by the suppliers, including the guidelines and objectives of quality assurance, management department review, document and record control, staffing and training, design control, procurement control, control of items, process control, inspection and testing control, non-conformance control, and internal and external QA audit, are analyzed in this article. The detailed QA audit checklist on these above mentioned aspects are described and the problems found in real QA audit are listed in this article. (authors)

  14. A MULTIDISCIPLINARY ANALYTICAL FRAMEWORK FOR STUDYING ACTIVE MOBILITY PATTERNS

    Directory of Open Access Journals (Sweden)

    D. Orellana

    2016-06-01

    Full Text Available Intermediate cities are urged to change and adapt their mobility systems from a high energy-demanding motorized model to a sustainable low-motorized model. In order to accomplish such a model, city administrations need to better understand active mobility patterns and their links to socio-demographic and cultural aspects of the population. During the last decade, researchers have demonstrated the potential of geo-location technologies and mobile devices to gather massive amounts of data for mobility studies. However, the analysis and interpretation of this data has been carried out by specialized research groups with relatively narrow approaches from different disciplines. Consequently, broader questions remain less explored, mainly those relating to spatial behaviour of individuals and populations with their geographic environment and the motivations and perceptions shaping such behaviour. Understanding sustainable mobility and exploring new research paths require an interdisciplinary approach given the complex nature of mobility systems and their social, economic and environmental impacts. Here, we introduce the elements for a multidisciplinary analytical framework for studying active mobility patterns comprised of three components: a Methodological, b Behavioural, and c Perceptual. We demonstrate the applicability of the framework by analysing mobility patterns of cyclists and pedestrians in an intermediate city integrating a range of techniques, including: GPS tracking, spatial analysis, auto-ethnography, and perceptual mapping. The results demonstrated the existence of non-evident spatial behaviours and how perceptual features affect mobility. This knowledge is useful for developing policies and practices for sustainable mobility planning.

  15. An analytical study of various telecomminication networks using Markov models

    International Nuclear Information System (INIS)

    Ramakrishnan, M; Jayamani, E; Ezhumalai, P

    2015-01-01

    The main aim of this paper is to examine issues relating to the performance of various Telecommunication networks, and applied queuing theory for better design and improved efficiency. Firstly, giving an analytical study of queues deals with quantifying the phenomenon of waiting lines using representative measures of performances, such as average queue length (on average number of customers in the queue), average waiting time in queue (on average time to wait) and average facility utilization (proportion of time the service facility is in use). In the second, using Matlab simulator, summarizes the finding of the investigations, from which and where we obtain results and describing methodology for a) compare the waiting time and average number of messages in the queue in M/M/1 and M/M/2 queues b) Compare the performance of M/M/1 and M/D/1 queues and study the effect of increasing the number of servers on the blocking probability M/M/k/k queue model. (paper)

  16. a Multidisciplinary Analytical Framework for Studying Active Mobility Patterns

    Science.gov (United States)

    Orellana, D.; Hermida, C.; Osorio, P.

    2016-06-01

    Intermediate cities are urged to change and adapt their mobility systems from a high energy-demanding motorized model to a sustainable low-motorized model. In order to accomplish such a model, city administrations need to better understand active mobility patterns and their links to socio-demographic and cultural aspects of the population. During the last decade, researchers have demonstrated the potential of geo-location technologies and mobile devices to gather massive amounts of data for mobility studies. However, the analysis and interpretation of this data has been carried out by specialized research groups with relatively narrow approaches from different disciplines. Consequently, broader questions remain less explored, mainly those relating to spatial behaviour of individuals and populations with their geographic environment and the motivations and perceptions shaping such behaviour. Understanding sustainable mobility and exploring new research paths require an interdisciplinary approach given the complex nature of mobility systems and their social, economic and environmental impacts. Here, we introduce the elements for a multidisciplinary analytical framework for studying active mobility patterns comprised of three components: a) Methodological, b) Behavioural, and c) Perceptual. We demonstrate the applicability of the framework by analysing mobility patterns of cyclists and pedestrians in an intermediate city integrating a range of techniques, including: GPS tracking, spatial analysis, auto-ethnography, and perceptual mapping. The results demonstrated the existence of non-evident spatial behaviours and how perceptual features affect mobility. This knowledge is useful for developing policies and practices for sustainable mobility planning.

  17. Analytical & Experimental Study of Radio Frequency Cavity Beam Profile Monitor

    Energy Technology Data Exchange (ETDEWEB)

    Balcazar, Mario D. [Fermilab; Yonehara, Katsuya [Fermilab

    2017-10-22

    The purpose of this analytical and experimental study is multifold: 1) To explore a new, radiation-robust, hadron beam profile monitor for intense neutrino beam applications; 2) To test, demonstrate, and develop a novel gas-filled Radio-Frequency (RF) cavity to use in this monitoring system. Within this context, the first section of the study analyzes the beam distribution across the hadron monitor as well as the ion-production rate inside the RF cavity. Furthermore a more effecient pixel configuration across the hadron monitor is proposed to provide higher sensitivity to changes in beam displacement. Finally, the results of a benchtop test of the tunable quality factor RF cavity will be presented. The proposed hadron monitor configuration consists of a circular array of RF cavities located at a radial distance of 7cm { corresponding to the standard deviation of the beam due to scatering { and a gas-filled RF cavity with a quality factor in the range 400 - 800.

  18. Analytical methods for study of transmission line lightning protection

    International Nuclear Information System (INIS)

    Pettersson, Per.

    1993-04-01

    Transmission line lightning performance is studied by analytical methods. The elements of shielding failure flashovers and back-flashovers are analysed as functions of incidence, response and insulation. Closed-form approximate expressions are sought to enhance understanding of the phenomena. Probabilistic and wave propagation aspects are particularly studied. The electrogeometric model of lightning attraction to structures is used in combination with the log-normal probability distribution of lightning to ground currents. The log-normality is found to be retained for the currents collected by mast-type as well as line-type structures, but with a change of scale. For both types, exceedingly simple formulas for the number of hits are derived. Simple closed-form expressions for the line outage rates from back- flashovers and shielding failure flashovers are derived in a uniform way as functions of the critical currents. The expressions involve the standardized normal distribution function. System response is analysed by use of Laplace transforms in combination with text-book transmission-line theory. Inversion into time domain is accomplished by an approximate asymptotic method producing closed-form results. The back-flashover problem is analysed in particular. Approximate, image type expressions are derived for shunt admittance of wires above, on and under ground for analyses of fast transients. The derivation parallels that for series impedance, now well-known. 3 refs, 5 figs

  19. Ecoregions of Arizona (poster)

    Science.gov (United States)

    Griffith, Glenn E.; Omernik, James M.; Johnson, Colleen Burch; Turner, Dale S.

    2014-01-01

    Ecoregions denote areas of general similarity in ecosystems and in the type, quality, and quantity of environmental resources; they are designed to serve as a spatial framework for the research, assessment, management, and monitoring of ecosystems and ecosystem components. By recognizing the spatial differences in the capacities and potentials of ecosystems, ecoregions stratify the environment by its probable response to disturbance. These general purpose regions are critical for structuring and implementing ecosystem management strategies across federal agencies, state agencies, and nongovernment organizations that are responsible for different types of resources within the same geographical areas. The Arizona ecoregion map was compiled at a scale of 1:250,000. It revises and subdivides an earlier national ecoregion map that was originally compiled at a smaller scale. The approach used to compile this map is based on the premise that ecological regions can be identified through the analysis of the spatial patterns and the composition of biotic and abiotic phenomena that affect or reflect differences in ecosystem quality and integrity. These phenomena include geology, physiography, vegetation, climate, soils, land use, wildlife, and hydrology. The relative importance of each characteristic varies from one ecological region to another regardless of the hierarchical level. A Roman numeral hierarchical scheme has been adopted for different levels of ecological regions. Level I is the coarsest level, dividing North America into 15 ecological regions. Level II divides the continent into 50 regions. At level III, the continental United States contains 105 ecoregions and the conterminous United States has 85 ecoregions. Level IV is a further subdivision of level III ecoregions. Arizona contains arid deserts and canyonlands, semiarid shrub- and grass-covered plains, woodland- and shrubland-covered hills, lava fields and volcanic plateaus, forested mountains, glaciated

  20. Application of QA to R ampersand D support of HLW programs

    International Nuclear Information System (INIS)

    Ryder, D.E.

    1988-01-01

    Quality has always been of primary importance in the research and development (R ampersand D) environment. An organization's ability to attract funds for new or continued research is largely dependent on the quality of past performance. However, with the possible exceptions of peer reviews for fund allocation and the referee process prior to publication, past quality assurance (QA) activities were primarily informal good practices. This resulted in standards of acceptable practice that varied from organization to organization. The increasing complexity of R ampersand D projects and the increasing need for project results to be upheld outside the scientific community (i.e., lawsuits and licensing hearings) are encouraging R ampersand D organizations and their clients to adopt more formalized methods for the scientific process and to increase control over support organizations (i.e., suppliers and subcontractors). This has become especially true for R ampersand D organizations involved in the high-level (HLW) projects for a number of years. The PNL began to implement QA program requirements within a few HLW repository preliminary studies in 1978. In 1985, PNL developed a comprehensive QA program for R ampersand D activities in support of two of the proposed repository projects. This QA program was developed by the PNL QA department with a significant amount of support assistance and guidance from PNL upper management, the Basalt Waste Isolation Project (BWIP), and the Salt Repository Program Office (SPRO). The QA program has been revised to add a three-level feature and is currently being implemented on projects sponsored by the Office of Geologic Repositories (DOE/OGR), Repository Technology Program (DOE-CH), Nevada Nuclear Waste Storage Investigation (NNWSI) Project, and other HLW projects

  1. DEMT experimental and analytical studies on seismic isolation

    International Nuclear Information System (INIS)

    Gantenbein, F.; Buland, P.

    1989-01-01

    Work on seismic isolation has been performed in France for many years, and the isolation device developed by SPIE-BATIGNOLLES in collaboration with Electricite de France (EDF) has been incorporated in the design of pressurized-water reactor (PWR) nuclear power plants. This paper reviews the experimental and theoretical studies performed at CEA/DEMT related to the overall behavior of isolated structures. The experimental work consists of the seismic shaking-table tests of a concrete cylinder isolated by neoprene sliding pads, and the vibrational tests on the reaction mass of the TAMARIS seismic facility. The analytical work consists of the development of procedures for dynamic calculation methods: for soil-structure interaction where pads are placed between an upper raft and pedestals, for time-history calculations where sliding plates are used, and for fluid-structure interaction where coupled fluid and structure motions and sloshing modes are important. Finally, this paper comments on the consequences of seismic isolation for the analysis of fast breeder reactor (FBR) vessels. The modes can no longer be considered independent (SRSS Method leads to important errors), and the sloshing increases

  2. Analytical study of solids-gas two phase flow

    International Nuclear Information System (INIS)

    Hosaka, Minoru

    1977-01-01

    Fundamental studies were made on the hydrodynamics of solids-gas two-phase suspension flow, in which very small solid particles are mixed in a gas flow to enhance the heat transfer characteristics of gas cooled high temperature reactors. Especially, the pressure drop due to friction and the density distribution of solid particles are theoretically analyzed. The friction pressure drop of two-phase flow was analyzed based on the analytical result of the single-phase friction pressure drop. The calculated values of solid/gas friction factor as a function of solid/gas mass loading are compared with experimental results. Comparisons are made for Various combinations of Reynolds number and particle size. As for the particle density distribution, some factors affecting the non-uniformity of distribution were considered. The minimum of energy dispersion was obtained with the variational principle. The suspension density of particles was obtained as a function of relative distance from wall and was compared with experimental results. It is concluded that the distribution is much affected by the particle size and that the smaller particles are apt to gather near the wall. (Aoki, K.)

  3. Ground penetrating radar geologic field studies of the ejecta of Barringer Meteorite Crater, Arizona, as a planetary analog

    Science.gov (United States)

    Russell, Patrick S.; Grant, John A.; Williams, Kevin K.; Carter, Lynn M.; Brent Garry, W.; Daubar, Ingrid J.

    2013-09-01

    penetrating radar (GPR) has been a useful geophysical tool in investigating a variety of shallow subsurface geological environments on Earth. Here we investigate the capabilities of GPR to provide useful geologic information in one of the most common geologic settings of planetary surfaces, impact crater ejecta. Three types of ejecta are surveyed with GPR at two wavelengths (400 MHz, 200 MHz) at Meteor Crater, Arizona, with the goal of capturing the GPR signature of the subsurface rock population. In order to "ground truth" the GPR characterization, subsurface rocks are visually counted and measured in preexisting subsurface exposures immediately adjacent to and below the GPR transect. The rock size-frequency distribution from 10 to 50 cm based on visual counts is well described by both power law and exponential functions, the former slightly better, reflecting the control of fragmentation processes during the impact-ejection event. GPR counts are found to overestimate the number of subsurface rocks in the upper meter (by a factor of 2-3x) and underestimate in the second meter of depth (0.6-1.0x), results attributable to the highly scattering nature of blocky ejecta. Overturned ejecta that is fractured yet in which fragments are minimally displaced from their complement fragments produces fewer GPR returns than well-mixed ejecta. The use of two wavelengths and division of results into multiple depth zones provides multiple aspects by which to characterize the ejecta block population. Remote GPR measurement of subsurface ejecta in future planetary situations with no subsurface exposure can be used to characterize those rock populations relative to that of Meteor Crater.

  4. Size Effect of the 2-D Bodies on the Geothermal Gradient and Q-A Plot

    Science.gov (United States)

    Thakur, M.; Blackwell, D. D.

    2009-12-01

    Using numerical models we have investigated some of the criticisms on the Q-A plot of related to the effect of size of the body on the slope and reduced heat flow. The effects of horizontal conduction depend on the relative difference of radioactivity between the body and the country rock (assuming constant thermal conductivity). Horizontal heat transfer due to different 2-D bodies was numerically studied in order to quantify resulting temperature differences at the Moho and errors on the predication of Qr (reduced heat flow). Using the two end member distributions of radioactivity, the step model (thickness 10km) and exponential model, different 2-D models of horizontal scale (width) ranging from 10 -500 km were investigated. Increasing the horizontal size of the body tends to move observations closer towards the 1-D solution. A temperature difference of 50 oC is produced (for the step model) at Moho between models of width 10 km versus 500 km. In other words the 1-D solution effectively provides large scale averaging in terms of heat flow and temperature field in the lithosphere. For bodies’ ≤ 100 km wide the geotherms at shallower levels are affected, but at depth they converge and are 50 oC lower than that of the infinite plate model temperature. In case of 2-D bodies surface heat flow is decreased due to horizontal transfer of heat, which will shift the Q-A point vertically downward on the Q-A plot. The smaller the size of the body, the more will be the deviation from the 1-D solution and the more will be the movement of Q-A point downwards on a Q-A plot. On the Q-A plot, a limited points of bodies of different sizes with different radioactivity contrast (for the step and exponential model), exactly reproduce the reduced heat flow Qr. Thus the size of the body can affect the slope on a Q-A plot but Qr is not changed. Therefore, Qr ~ 32 mWm-2 obtained from the global terrain average Q-A plot represents the best estimate of stable continental mantle heat

  5. Manufacturing and QA of adaptors for LHC

    International Nuclear Information System (INIS)

    Madhu Murthy, V.; Dwivedi, J.; Goswami, S.G.; Soni, H.C.; Mainaud Durand, H.; Quesnel, J.P.; )

    2006-01-01

    The LHC low beta quadrupoles, have very tight alignment tolerances and are located in areas with strong radiation field. They require remote re-alignment, by motorized jacks, based on the feedback of alignment sensors of each magnet. Jacks designed to support arc cryomagnets of LHC are modified and motorized with the help of adaptors. Two types of adapters, for vertical and transverse axes of the jacks, were developed and supplied through collaboration between RRCAT, DAE, India and CERN, Geneva. This paper describes their functional requirements, manufacture and quality assurance (QA). (author)

  6. Systematic analytical characterization of new psychoactive substances: A case study.

    Science.gov (United States)

    Lobo Vicente, Joana; Chassaigne, Hubert; Holland, Margaret V; Reniero, Fabiano; Kolář, Kamil; Tirendi, Salvatore; Vandecasteele, Ine; Vinckier, Inge; Guillou, Claude

    2016-08-01

    New psychoactive substances (NPS) are synthesized compounds that are not usually covered by European and/or international laws. With a slight alteration in the chemical structure of existing illegal substances registered in the European Union (EU), these NPS circumvent existing controls and are thus referred to as "legal highs". They are becoming increasingly available and can easily be purchased through both the internet and other means (smart shops). Thus, it is essential that the identification of NPS keeps up with this rapidly evolving market. In this case study, the Belgian Customs authorities apprehended a parcel, originating from China, containing two samples, declared as being "white pigments". For routine identification, the Belgian Customs Laboratory first analysed both samples by gas-chromatography mass-spectrometry and Fourier-Transform Infrared spectroscopy. The information obtained by these techniques is essential and can give an indication of the chemical structure of an unknown substance but not the complete identification of its structure. To bridge this gap, scientific and technical support is ensured by the Joint Research Centre (JRC) to the European Commission Directorate General for Taxation and Customs Unions (DG TAXUD) and the Customs Laboratory European Network (CLEN) through an Administrative Arrangement for fast recognition of NPS and identification of unknown chemicals. The samples were sent to the JRC for a complete characterization using advanced techniques and chemoinformatic tools. The aim of this study was also to encourage the development of a science-based policy driven approach on NPS. These samples were fully characterized and identified as 5F-AMB and PX-3 using (1)H and (13)C nuclear magnetic resonance (NMR), high-resolution tandem mass-spectrometry (HR-MS/MS) and Raman spectroscopy. A chemoinformatic platform was used to manage, unify analytical data from multiple techniques and instruments, and combine it with chemical and

  7. Biological and analytical studies of peritoneal dialysis solutions

    Directory of Open Access Journals (Sweden)

    N. Hudz

    2018-04-01

    Full Text Available The purpose of our work was to conduct biological and analytical studies of the peritoneal dialysis (PD solutions containing glucose and sodium lactate and establish correlations between cell viability of the Vero cell line and values of analytical indexes of the tested solutions. The results of this study confirm the cytotoxicity of the PD solutions even compared with the isotonic solution of sodium chloride, which may be due to the low pH of the solutions, presence of glucose degradation products (GDPs and high osmolarity of the solutions, and unphysiological concentrations of glucose and sodium lactate. However, it is not yet known what factors or their combination and to what extent cause the cytotoxicity of PD solutions. In the neutral red (NR test the weak, almost middle (r = -0.496 and 0.498, respectively and unexpected correlations were found between reduced viability of monkey kidney cells and increased pH of the PD solutions and between increased cell viability and increased absorbance at 228 nm of the tested PD solutions. These two correlations can be explained by a strong correlation (r = -0.948 between a decrease in pH and an increase in the solution absorbance at 228 nm. The opposite effect was observed in the MTT test. The weak, but expected correlations (r = 0.32 and -0.202, respectively were found between increased cell viability and increased pH in the PD solutions and between decreased cell viability and increased absorbance at 228 nm of the tested PD solutions. The middle and weak correlations (r = 0.56 and 0.29, respectively were detected between increased cell viability and increased lactate concentration in the NR test and MTT test. The data of these correlations can be partially explained by the fact that a correlation with a coefficient r = -0.34 was found between decreased pH in the solutions and increased lactate concentration. The very weak correlations (0.138 and 0.196, respectively were found between increased cell

  8. Experimental and analytical study of the sputtering phenomena

    International Nuclear Information System (INIS)

    Howard, P.A.

    1976-03-01

    One form of the sputtering phenomena, the heat-transfer process that occurs when an initially hot vertical surface is cooled by a falling liquid film, was examined from a new experimental approach. The sputtering front is the lowest wetted position on the vertical surface and is characterized by a short region of intense nucleate boiling. The sputtering front progresses downward at nearly a constant rate, the surface below the sputtering front being dry and almost adiabatic. This heat-transfer process is of interest in the analysis of some of the performance aspects of emergency core-cooling systems of light-water reactors. An experimental apparatus was constructed to examine the heat-transfer characteristics of a sputtering front. In the present study, a heat source of sufficient intensity was located immediately below the sputtering front, which prevented its downward progress, thus permitting detailed measurements of steady-state surface temperatures throughout a sputtering front. Experimental evidence showed the sputtering front to correspond to a critical heat-flux (CHF) phenomenon. Data were obtained with water flow rates of 350-1600 lb/sub m//hr-ft and subcoolings of 40-140 0 F on a 3 / 8 -in. solid copper rod at 1 atm. A two-dimensional analytical model was developed to describe a stationary sputtering front where the wet-dry interface corresponds to a CHF phenomena and the dry zone is adiabatic. This model is nonlinear because of the temperature dependence of the heat-transfer coefficient in the wetted region and has yielded good agreement with data. A simplified one-dimensional approximation was developed which adequately describes these data. Finally, by means of a coordinate transformation and additional simplifying assumptions, this analysis was extended to analyze moving sputtering fronts, and reasonably good agreement with reported data was shown

  9. [Pregnancy-Associated Breast Cancer: An analytical observational study].

    Science.gov (United States)

    Baulies, Sonia; Cusidó, Maite; Tresserra, Francisco; Rodríguez, Ignacio; Ubeda, Belén; Ara, Carmen; Fábregas, Rafael

    2014-03-04

    Pregnancy-associated breast cancer is defined as breast cancer diagnosed during pregnancy and up to one year postpartum. A retrospective, analytical, observational study comparing 56 cases of breast cancer and pregnancy (PABC) diagnosed 1976-2008 with 73 patients with breast cancer not associated with pregnancy (non-PABC) was performed. Demographic data, prognostic factors, treatment and survival were reviewed and compared. The prevalence of PABC in our center is 8.3/10,000. The highest frequency (62%) appeared during the postpartum period. The stages are higher in PABC, being 31.3% advanced (EIII and EIV) in PABC versus 13.3% in non-PABC (P < .05). Regarding prognostic factors, 27.3% in PABC had a tumoral grade 3 versus 15.8% of non-PABC. Among women with PABC, 33.3% had negative estrogen receptors, 48.7% negative progesterone receptors and 34.5% positive Her2Neu compared with 22.2, 24.1 and 31%, respectively of non-PABC patients. Finally, positive lymph nodes were found in 52.8% of PABC, versus 33.8% non-PABC (P < .05). Overall and disease-free survival rate at 5 years for PABC was 63.7 and 74.2%, respectively. The poorer survival observed is possibly due to the presence of adverse prognostic features such as lymph node metastases, negative hormone receptors, tumoral grade iii, as well as a delay in diagnosis with a higher rate of advanced stages. Copyright © 2012 Elsevier España, S.L. All rights reserved.

  10. Determination of serum albumin, analytical challenges: a French multicenter study.

    Science.gov (United States)

    Rossary, Adrien; Blondé-Cynober, Françoise; Bastard, Jean-Philippe; Beauvieux, Marie-Christine; Beyne, Pascale; Drai, Jocelyne; Lombard, Christine; Anglard, Ingrid; Aussel, Christian; Claeyssens, Sophie; Vasson, Marie-Paule

    2017-06-01

    Among the biological markers of morbidity and mortality, albumin holds a key place in the range of criteria used by the High Authority for Health (HAS) for the assessment of malnutrition and the coding of information system medicalization program (PMSI). If the principle of quantification methods have not changed in recent years, the dispersion of external evaluations of the quality (EEQ) data shows that the standardization using the certified reference material (CRM) 470 is not optimal. The aim of this multicenter study involving 7 sites, conducted by a working group of the French Society of Clinical Biology (SFBC), was to assess whether the albuminemia values depend on the analytical system used. The albumin from plasma (n=30) and serum (n=8) pools was quantified by 5 different methods [bromocresol green (VBC) and bromocresol purple (PBC) colorimetry, immunoturbidimetry (IT), immunonephelometry (IN) and capillary electrophoresis (CE)] using 12 analyzers. Bland and Altman's test evaluated the difference between the results obtained by the different methods. For example, a difference as high as 13 g/L was observed for the same sample between the methods (p albumin across the range of values tested compared to PBC (p albumin values inducing a difference of performance between the immunoprecipitation methods (IT vs IN, p albumin results are related to the technical/analyzer tandem used. This variability is usually not taken into account by the clinician. Thus, clinicians and biologists have to be aware and have to check, depending on the method used, the albumin thresholds identified as risk factors for complications related to malnutrition and PMSI coding.

  11. Interactions between $U(1)$ Cosmic Strings: An Analytical Study

    OpenAIRE

    Bettencourt, L. M. A.; Rivers, R. J.

    1994-01-01

    We derive analytic expressions for the interaction energy between two general $U(1)$ cosmic strings as the function of their relative orientation and the ratio of the coupling constants in the model. The results are relevant to the statistic description of strings away from critical coupling and shed some light on the mechanisms involved in string formation and the evolution of string networks.

  12. Accounting for human factor in QC and QA inspections

    International Nuclear Information System (INIS)

    Goodman, J.

    1986-01-01

    Two types of human error during QC/QA inspection have been identified. The method of accounting for the effects of human error in QC/QA inspections was developed. The result of evaluation of the proportion of discrepant items in the population is affected significantly by human factor

  13. Examining Arizona's Policy Response Post "Flores v. Arizona" in Educating K-12 English Language Learners

    Science.gov (United States)

    Jimenez-Silva, Margarita; Gomez, Laura; Cisneros, Jesus

    2014-01-01

    This article provides an analysis of Arizona's policy response in educating English language learners by conducting a narrative review. A critical Latina/o theory approach was used to analyze the data. This study reveals 5 salient policy responses: (a) severely limit bilingual education, (b) develop controversial funding solutions, (c) implement a…

  14. Summary Report for the Evaluation of Current QA Processes Within the FRMAC FAL and EPA MERL.

    Energy Technology Data Exchange (ETDEWEB)

    Shanks, Sonoya T.; Ted Redding; Lynn Jaussi; Allen, Mark B.; Fournier, Sean Donovan; Leonard, Elliott J.

    2017-04-01

    The Federal Radiological Monitoring and Assessment Center (FRMAC) relies on accurate and defensible analytical laboratory data to support its mission. Therefore, FRMAC must ensure that the environmental analytical laboratories providing analytical services maintain an ongoing capability to provide accurate analytical results to DOE. It is undeniable that the more Quality Assurance (QA) and Quality Control (QC) measures required of the laboratory, the less resources that are available for analysis of response samples. Being that QA and QC measures in general are understood to comprise a major effort related to a laboratory’s operations, requirements should only be considered if they are deemed “value-added” for the FRMAC mission. This report provides observations of areas for improvement and potential interoperability opportunities in the areas of Batch Quality Control Requirements, Written Communications, Data Review Processes, Data Reporting Processes, along with the lessons learned as they apply to items in the early phase of a response that will be critical for developing a more efficient, integrated response for future interactions between the FRMAC and EPA assets.

  15. Analytical and Numerical Studies of Several Fluid Mechanical Problems

    Science.gov (United States)

    Kong, D. L.

    2014-03-01

    In this thesis, three parts, each with several chapters, are respectively devoted to hydrostatic, viscous, and inertial fluids theories and applications. Involved topics include planetary, biological fluid systems, and high performance computing technology. In the hydrostatics part, the classical Maclaurin spheroids theory is generalized, for the first time, to a more realistic multi-layer model, establishing geometries of both the outer surface and the interfaces. For one of its astrophysical applications, the theory explicitly predicts physical shapes of surface and core-mantle-boundary for layered terrestrial planets, which enables the studies of some gravity problems, and the direct numerical simulations of dynamo flows in rotating planetary cores. As another application of the figure theory, the zonal flow in the deep atmosphere of Jupiter is investigated for a better understanding of the Jovian gravity field. An upper bound of gravity field distortions, especially in higher-order zonal gravitational coefficients, induced by deep zonal winds is estimated firstly. The oblate spheroidal shape of an undistorted Jupiter resulting from its fast solid body rotation is fully taken into account, which marks the most significant improvement from previous approximation based Jovian wind theories. High viscosity flows, for example Stokes flows, occur in a lot of processes involving low-speed motions in fluids. Microorganism swimming is such a typical case. A fully three dimensional analytic solution of incompressible Stokes equation is derived in the exterior domain of an arbitrarily translating and rotating prolate spheroid, which models a large family of microorganisms such as cocci bacteria. The solution is then applied to the magnetotactic bacteria swimming problem, and good consistency has been found between theoretical predictions and laboratory observations of the moving patterns of such bacteria under magnetic fields. In the analysis of dynamics of planetary

  16. Review of Factor Analytic Studies Examining Symptoms of Autism Spectrum Disorders

    Science.gov (United States)

    Shuster, Jill; Perry, Adrienne; Bebko, James; Toplak, Maggie E.

    2014-01-01

    Factor analytic studies have been conducted to examine the inter-relationships and degree of overlap among symptoms in Autism Spectrum Disorder (ASD). This paper reviewed 36 factor analytic studies that have examined ASD symptoms, using 13 different instruments. Studies were grouped into three categories: Studies with all DSM-IV symptoms, studies…

  17. Semi Active Control of Civil Structures, Analytical and Numerical Studies

    Science.gov (United States)

    Kerboua, M.; Benguediab, M.; Megnounif, A.; Benrahou, K. H.; Kaoulala, F.

    numerical example of the parallel R-L piezoelectric vibration shunt control simulated with MATLAB® is presented. An analytical study of the resistor-inductor (R-L) passive piezoelectric vibration shunt control of a cantilever beam was undertaken. The modal and strain analyses were performed by varying the material properties and geometric configurations of the piezoelectric transducer in relation to the structure in order to maximize the mechanical strain produced in the piezoelectric transducer.

  18. Effect of a family history of psoriasis and age on comorbidities and quality of life in patients with moderate to severe psoriasis: Results from the ARIZONA study.

    Science.gov (United States)

    López-Estebaranz, Jose Luis; Sánchez-Carazo, Jose Luis; Sulleiro, Sara

    2016-04-01

    Psoriasis is a chronic inflammatory skin disease whose clinical characteristics vary from patient to patient. We aimed to analyze how comorbidities and quality of life (QoL, as per the Dermatology Life Quality Index [DLQI]) may be affected by a family history of psoriasis and by age. The ARIZONA study was a multicenter, cross-sectional study in 1022 adult patients diagnosed with moderate to severe psoriasis at least 6 months prior to inclusion. The severity of psoriasis and the proportion of patients with comorbidities were not affected by the presence of a family history. The regression analysis revealed that the presence of a family history of psoriasis was associated with the effect on the patient's QoL (P = 0.002), regardless of disease severity. The mean DLQI total score varied significantly across age groups (5.1 ± 5.3 for the 18-30-year group, 5.7 ± 6.5 for the 31-60-year group and 3.8 ± 5.1 for the >60-year group; P = 0.001). In conclusion, the presence of a family history of psoriasis appears to disrupt QoL in patients with moderate to severe psoriasis, but it hardly affected the prevalence of comorbid conditions. The effect of age on QoL was particularly noticeable in younger patients, highlighting its negative impact. As expected, older patients appeared to be burdened with a higher number of comorbidities than their younger counterparts. © 2015 Japanese Dermatological Association.

  19. SU-E-J-52: Decreasing Frequency of Performing TG-142 Imaging QA – 5 Year Experience

    Energy Technology Data Exchange (ETDEWEB)

    Lin, T; Ma, C [Fox Chase Cancer Center, Philadelphia, PA (United States)

    2015-06-15

    Purpose This study is an update to check if the frequency of imaging QA suggested by AAPM Task Group Report 142 (TG142) is necessary with our 5 year experience. TG142 presents recommendations for QA criteria of IGRT treatment. ACR has adopted it to be the requirements for any radiatiotherapy practices; however, we propose to reduce the frequency on image quality QA according to this 5 year study.Method and Materials: This study uses VarianIX2100 and Siemens Artiste Linacs to perform QAs on KV, MV, CBCT modalities. The QA was designed following under the recommendations of TG142. This study reports the daily imaging positioning/repositioning and imaging and treatment coordinate coincidence. QA results on kV, MV and CBCT from 4/7/2010∼3/11/15 are analyzed. KV, MV, CBCT images are taken with the Varian isocube localized at the isocenter. Digital graticule is used in the software to verify the isocenter position. CBCT images are taken with the cube placed at 1cm superior, lateral and anterior of the isocenter. In-line fusion software is used to verify the contrived shift. Digital ruler provided at the on-board-imaging software or adaptive-targeting software was used to measure the position differences. The position differences were recorded at AP,LR,SI directions. Results 5 year records on kV, MV, CBCT show the shifts in all three directions are within the tolerance of 1mm suggested in TG142 for stereotactic radiation treatment(SRS/SRT). There is no occasion where shifts are outside 1mm tolerance. Conclusions The daily imaging QA suggested in TG142 is useful in ensuring the accuracy needed for SRS/SRT in IGRT. 5 year measurements presented suggest that decreasing the frequency of imaging QA may be acceptable, in particular for institutions reporting no violation of tolerance over periods of few years.

  20. SU-E-J-52: Decreasing Frequency of Performing TG-142 Imaging QA – 5 Year Experience

    International Nuclear Information System (INIS)

    Lin, T; Ma, C

    2015-01-01

    Purpose This study is an update to check if the frequency of imaging QA suggested by AAPM Task Group Report 142 (TG142) is necessary with our 5 year experience. TG142 presents recommendations for QA criteria of IGRT treatment. ACR has adopted it to be the requirements for any radiatiotherapy practices; however, we propose to reduce the frequency on image quality QA according to this 5 year study.Method and Materials: This study uses VarianIX2100 and Siemens Artiste Linacs to perform QAs on KV, MV, CBCT modalities. The QA was designed following under the recommendations of TG142. This study reports the daily imaging positioning/repositioning and imaging and treatment coordinate coincidence. QA results on kV, MV and CBCT from 4/7/2010∼3/11/15 are analyzed. KV, MV, CBCT images are taken with the Varian isocube localized at the isocenter. Digital graticule is used in the software to verify the isocenter position. CBCT images are taken with the cube placed at 1cm superior, lateral and anterior of the isocenter. In-line fusion software is used to verify the contrived shift. Digital ruler provided at the on-board-imaging software or adaptive-targeting software was used to measure the position differences. The position differences were recorded at AP,LR,SI directions. Results 5 year records on kV, MV, CBCT show the shifts in all three directions are within the tolerance of 1mm suggested in TG142 for stereotactic radiation treatment(SRS/SRT). There is no occasion where shifts are outside 1mm tolerance. Conclusions The daily imaging QA suggested in TG142 is useful in ensuring the accuracy needed for SRS/SRT in IGRT. 5 year measurements presented suggest that decreasing the frequency of imaging QA may be acceptable, in particular for institutions reporting no violation of tolerance over periods of few years

  1. A virtual dosimetry audit - Towards transferability of gamma index analysis between clinical trial QA groups.

    Science.gov (United States)

    Hussein, Mohammad; Clementel, Enrico; Eaton, David J; Greer, Peter B; Haworth, Annette; Ishikura, Satoshi; Kry, Stephen F; Lehmann, Joerg; Lye, Jessica; Monti, Angelo F; Nakamura, Mitsuhiro; Hurkmans, Coen; Clark, Catharine H

    2017-12-01

    Quality assurance (QA) for clinical trials is important. Lack of compliance can affect trial outcome. Clinical trial QA groups have different methods of dose distribution verification and analysis, all with the ultimate aim of ensuring trial compliance. The aim of this study was to gain a better understanding of different processes to inform future dosimetry audit reciprocity. Six clinical trial QA groups participated. Intensity modulated treatment plans were generated for three different cases. A range of 17 virtual 'measurements' were generated by introducing a variety of simulated perturbations (such as MLC position deviations, dose differences, gantry rotation errors, Gaussian noise) to three different treatment plan cases. Participants were blinded to the 'measured' data details. Each group analysed the datasets using their own gamma index (γ) technique and using standardised parameters for passing criteria, lower dose threshold, γ normalisation and global γ. For the same virtual 'measured' datasets, different results were observed using local techniques. For the standardised γ, differences in the percentage of points passing with γ audit has been an informative step in understanding differences in the verification of measured dose distributions between different clinical trial QA groups. This work lays the foundations for audit reciprocity between groups, particularly with more clinical trials being open to international recruitment. Copyright © 2017 Elsevier B.V. All rights reserved.

  2. Job satisfaction among Arizona adult nurse practitioners.

    Science.gov (United States)

    Schiestel, Charlotte

    2007-01-01

    A literature review for studies of job satisfaction among nurse practitioners (NPs) suggests that the true determinants of job satisfaction have not been discovered. The purpose of this study was to determine job satisfaction among adult health NPs (ANPs) practicing in Arizona. The Misener nurse practitioner job satisfaction scale was mailed to 329 Arizona ANPs who were certified by the Arizona State Board of Nursing (47% response rate). The mean overall satisfaction score was 4.69 out of a possible score of 6.0 for very satisfied. Differences in employer type, gender, annual income, membership in professional nursing organization, or full-time versus part-time employment status did not result in significantly different scores on the job satisfaction scale in this group. A deep and sustained nursing shortage, the exodus of experienced nurses from the profession, and a projected shortage of primary care providers have generated interest among professional groups, private and government healthcare commissions, and the healthcare industry in determining what factors may influence an individual to choose and remain active in nursing practice. Researchers, educators, employers, and the healthcare industry must look beyond well-worn assumptions about job satisfaction to explore what the individual NP finds satisfying about his or her role.

  3. ANALYTICAL APPROACHES TO THE STUDY OF EXPORT TRANSACTIONS

    Directory of Open Access Journals (Sweden)

    Ekaterina Viktorovna Medvedeva

    2015-12-01

    Full Text Available Analytical approaches to research of export operations depend on the conditions containing in separate external economic contracts with foreign buyers and also on a form of an exit of the Russian supplier of export goods to a foreign market. By means of analytical procedures it is possible to foresee and predict admissible situations which can have an adverse effect on a financial position of the economic subject. The economic entity, the engaged foreign economic activity, has to carry out surely not only the analysis of the current activity, but also the analysis of export operations. In article analytical approaches of carrying out the analysis of export operations are considered, on an example the analysis of export operations in dynamics is submitted, it is recommended to use the formulas allowing to estimate export in dynamics. For the comparative analysis export volume in the comparable prices is estimated. On the commodity groups including and quantitatively and qualitatively commensurable goods, the index of quantitative structure is calculated, the coefficient of delay of delivery of goods in comparison with other periods pays off. Carrying out the analysis allows to determine a tendency of change of export deliveries by export operations for the analyzed period for adoption of administrative decisions.Purpose Definition of the ways and receptions of the analysis applying when carrying out the analysis of export operations.Methodology in article economic-mathematical methods, and also statistical methods of the analysis were used.Results: the most informative parameters showing some aspects of carrying out the analysis of export operations are received.Practical implications it is expedient to apply the received results the economic subjects which are carrying out foreign economic activity, one of which elements are export operations.

  4. SU-E-CAMPUS-T-04: Statistical Process Control for Patient-Specific QA in Proton Beams

    Energy Technology Data Exchange (ETDEWEB)

    LAH, J [Myongji Hospital, Goyangsi, Gyeonggi-do (Korea, Republic of); SHIN, D [National Cancer Center, Goyangsi, Gyeonggi-do (Korea, Republic of); Kim, G [UCSD Medical Center, La Jolla, CA (United States)

    2014-06-15

    Purpose: To evaluate and improve the reliability of proton QA process, to provide an optimal customized level using the statistical process control (SPC) methodology. The aim is then to suggest the suitable guidelines for patient-specific QA process. Methods: We investigated the constancy of the dose output and range to see whether it was within the tolerance level of daily QA process. This study analyzed the difference between the measured and calculated ranges along the central axis to suggest the suitable guidelines for patient-specific QA in proton beam by using process capability indices. In this study, patient QA plans were classified into 6 treatment sites: head and neck (41 cases), spinal cord (29 cases), lung (28 cases), liver (30 cases), pancreas (26 cases), and prostate (24 cases). Results: The deviations for the dose output and range of daily QA process were ±0.84% and ±019%, respectively. Our results show that the patient-specific range measurements are capable at a specification limit of ±2% in all treatment sites except spinal cord cases. In spinal cord cases, comparison of process capability indices (Cp, Cpm, Cpk ≥1, but Cpmk ≤1) indicated that the process is capable, but not centered, the process mean deviates from its target value. The UCL (upper control limit), CL (center line) and LCL (lower control limit) for spinal cord cases were 1.37%, −0.27% and −1.89%, respectively. On the other hands, the range differences in prostate cases were good agreement between calculated and measured values. The UCL, CL and LCL for prostate cases were 0.57%, −0.11% and −0.78%, respectively. Conclusion: SPC methodology has potential as a useful tool to customize an optimal tolerance levels and to suggest the suitable guidelines for patient-specific QA in clinical proton beam.

  5. Analytical study of stress and deformation of HTR fuel blocks

    International Nuclear Information System (INIS)

    Tanaka, M.

    1982-01-01

    A two-dimensional finite element computer code named HANS-GR has been developed to predict the mechanical behavior of the graphite fuel blocks with realistic material properties and core environment. When graphite material is exposed to high temperature and fast neutron flux of high density, strains arise due to thermal expansion, irradiation-induced shrinkage and creep. Thus stresses and distortions are induced in the fuel block in which there are spatial variation of these strains. The analytical method used in the program to predcit these induced stresses and distortions by finite element method is discussed. In order to illustrate the versatility of the computer code, numerical results of two example analyses of the multi-hole type fuel elements in the VHTR Reactor are given. Two example analyses presented are those concerning the stresses in fuel blocks with control rod holes and distortions of the fuel blocks at the periphery of the reactor core. It is considered these phenomena should be carefully examined when the multi-hole type fuel elements are applied to VHTR. It is assured that the predicted mechanical behavior of the graphite components is strongly dependent on the material properties used and obtaining the reliable material property is important to make the analytical prediction a reliable one

  6. Target normal sheath acceleration analytical modeling, comparative study and developments

    International Nuclear Information System (INIS)

    Perego, C.; Batani, D.; Zani, A.; Passoni, M.

    2012-01-01

    Ultra-intense laser interaction with solid targets appears to be an extremely promising technique to accelerate ions up to several MeV, producing beams that exhibit interesting properties for many foreseen applications. Nowadays, most of all the published experimental results can be theoretically explained in the framework of the target normal sheath acceleration (TNSA) mechanism proposed by Wilks et al. [Phys. Plasmas 8(2), 542 (2001)]. As an alternative to numerical simulation various analytical or semi-analytical TNSA models have been published in the latest years, each of them trying to provide predictions for some of the ion beam features, given the initial laser and target parameters. However, the problem of developing a reliable model for the TNSA process is still open, which is why the purpose of this work is to enlighten the present situation of TNSA modeling and experimental results, by means of a quantitative comparison between measurements and theoretical predictions of the maximum ion energy. Moreover, in the light of such an analysis, some indications for the future development of the model proposed by Passoni and Lontano [Phys. Plasmas 13(4), 042102 (2006)] are then presented.

  7. Refinement of MLC modeling improves commercial QA dosimetry system for SRS and SBRT patient-specific QA.

    Science.gov (United States)

    Hillman, Yair; Kim, Josh; Chetty, Indrin; Wen, Ning

    2018-04-01

    dosimetry, MLC modeling, and inhomogeneity corrections in the beam model for SRS/SBRT QA. The improvements noted in this study, and further collaborations between clinical physicists and the vendor to refine the M3D beam model could enable M3D to become a premier SRS/SBRT QA tool. © 2018 American Association of Physicists in Medicine.

  8. MO-A-16A-01: QA Procedures and Metrics: In Search of QA Usability

    Energy Technology Data Exchange (ETDEWEB)

    Sathiaseelan, V [Northwestern Memorial Hospital, Chicago, IL (United States); Thomadsen, B [University of Wisconsin, Madison, WI (United States)

    2014-06-15

    Radiation therapy has undergone considerable changes in the past two decades with a surge of new technology and treatment delivery methods. The complexity of radiation therapy treatments has increased and there has been increased awareness and publicity about the associated risks. In response, there has been proliferation of guidelines for medical physicists to adopt to ensure that treatments are delivered safely. Task Group recommendations are copious, and clinical physicists' hours are longer, stretched to various degrees between site planning and management, IT support, physics QA, and treatment planning responsibilities.Radiation oncology has many quality control practices in place to ensure the delivery of high-quality, safe treatments. Incident reporting systems have been developed to collect statistics about near miss events at many radiation oncology centers. However, tools are lacking to assess the impact of these various control measures. A recent effort to address this shortcoming is the work of Ford et al (2012) who recently published a methodology enumerating quality control quantification for measuring the effectiveness of safety barriers. Over 4000 near-miss incidents reported from 2 academic radiation oncology clinics were analyzed using quality control quantification, and a profile of the most effective quality control measures (metrics) was identified.There is a critical need to identify a QA metric to help the busy clinical physicists to focus their limited time and resources most effectively in order to minimize or eliminate errors in the radiation treatment delivery processes. In this symposium the usefulness of workflows and QA metrics to assure safe and high quality patient care will be explored.Two presentations will be given:Quality Metrics and Risk Management with High Risk Radiation Oncology ProceduresStrategies and metrics for quality management in the TG-100 Era Learning Objectives: Provide an overview and the need for QA usability

  9. MO-A-16A-01: QA Procedures and Metrics: In Search of QA Usability

    International Nuclear Information System (INIS)

    Sathiaseelan, V; Thomadsen, B

    2014-01-01

    Radiation therapy has undergone considerable changes in the past two decades with a surge of new technology and treatment delivery methods. The complexity of radiation therapy treatments has increased and there has been increased awareness and publicity about the associated risks. In response, there has been proliferation of guidelines for medical physicists to adopt to ensure that treatments are delivered safely. Task Group recommendations are copious, and clinical physicists' hours are longer, stretched to various degrees between site planning and management, IT support, physics QA, and treatment planning responsibilities.Radiation oncology has many quality control practices in place to ensure the delivery of high-quality, safe treatments. Incident reporting systems have been developed to collect statistics about near miss events at many radiation oncology centers. However, tools are lacking to assess the impact of these various control measures. A recent effort to address this shortcoming is the work of Ford et al (2012) who recently published a methodology enumerating quality control quantification for measuring the effectiveness of safety barriers. Over 4000 near-miss incidents reported from 2 academic radiation oncology clinics were analyzed using quality control quantification, and a profile of the most effective quality control measures (metrics) was identified.There is a critical need to identify a QA metric to help the busy clinical physicists to focus their limited time and resources most effectively in order to minimize or eliminate errors in the radiation treatment delivery processes. In this symposium the usefulness of workflows and QA metrics to assure safe and high quality patient care will be explored.Two presentations will be given:Quality Metrics and Risk Management with High Risk Radiation Oncology ProceduresStrategies and metrics for quality management in the TG-100 Era Learning Objectives: Provide an overview and the need for QA usability

  10. On the use of biomathematical models in patient-specific IMRT dose QA

    Energy Technology Data Exchange (ETDEWEB)

    Zhen Heming [UT Southwestern Medical Center, Dallas, Texas 75390 (United States); Nelms, Benjamin E. [Canis Lupus LLC, Merrimac, Wisconsin 53561 (United States); Tome, Wolfgang A. [Department of Radiation Oncology, Division of Medical Physics, Montefiore Medical Center and Institute of Onco-Physics, Albert Einstein College of Medicine, Bronx, New York 10461 (United States)

    2013-07-15

    Purpose: To investigate the use of biomathematical models such as tumor control probability (TCP) and normal tissue complication probability (NTCP) as new quality assurance (QA) metrics.Methods: Five different types of error (MLC transmission, MLC penumbra, MLC tongue and groove, machine output, and MLC position) were intentionally induced to 40 clinical intensity modulated radiation therapy (IMRT) patient plans (20 H and N cases and 20 prostate cases) to simulate both treatment planning system errors and machine delivery errors in the IMRT QA process. The changes in TCP and NTCP for eight different anatomic structures (H and N: CTV, GTV, both parotids, spinal cord, larynx; prostate: CTV, rectal wall) were calculated as the new QA metrics to quantify the clinical impact on patients. The correlation between the change in TCP/NTCP and the change in selected DVH values was also evaluated. The relation between TCP/NTCP change and the characteristics of the TCP/NTCP curves is discussed.Results:{Delta}TCP and {Delta}NTCP were summarized for each type of induced error and each structure. The changes/degradations in TCP and NTCP caused by the errors vary widely depending on dose patterns unique to each plan, and are good indicators of each plan's 'robustness' to that type of error.Conclusions: In this in silico QA study the authors have demonstrated the possibility of using biomathematical models not only as patient-specific QA metrics but also as objective indicators that quantify, pretreatment, a plan's robustness with respect to possible error types.

  11. On the use of biomathematical models in patient-specific IMRT dose QA

    International Nuclear Information System (INIS)

    Zhen Heming; Nelms, Benjamin E.; Tomé, Wolfgang A.

    2013-01-01

    Purpose: To investigate the use of biomathematical models such as tumor control probability (TCP) and normal tissue complication probability (NTCP) as new quality assurance (QA) metrics.Methods: Five different types of error (MLC transmission, MLC penumbra, MLC tongue and groove, machine output, and MLC position) were intentionally induced to 40 clinical intensity modulated radiation therapy (IMRT) patient plans (20 H and N cases and 20 prostate cases) to simulate both treatment planning system errors and machine delivery errors in the IMRT QA process. The changes in TCP and NTCP for eight different anatomic structures (H and N: CTV, GTV, both parotids, spinal cord, larynx; prostate: CTV, rectal wall) were calculated as the new QA metrics to quantify the clinical impact on patients. The correlation between the change in TCP/NTCP and the change in selected DVH values was also evaluated. The relation between TCP/NTCP change and the characteristics of the TCP/NTCP curves is discussed.Results:ΔTCP and ΔNTCP were summarized for each type of induced error and each structure. The changes/degradations in TCP and NTCP caused by the errors vary widely depending on dose patterns unique to each plan, and are good indicators of each plan's “robustness” to that type of error.Conclusions: In this in silico QA study the authors have demonstrated the possibility of using biomathematical models not only as patient-specific QA metrics but also as objective indicators that quantify, pretreatment, a plan's robustness with respect to possible error types

  12. Analytical study of electron flows with a virtual cathode

    International Nuclear Information System (INIS)

    Dubinov, A.E.

    2000-01-01

    The dynamics of the electron flow behavior by its injection into a half-space is considered. Two problems are considered, namely the long-term injection of a monoenergetic electron flow and instantaneous flow injection with an assigned electron energy spectrum. The all flow electrons in both cases return to the injection plane. The simple analytical self-consistent model of the initial stage of the virtual cathode formation in a plane-parallel equipotential gap is plotted in the course of analysis whereof the duration of the virtual cathode formation process is determined. The performance of this model is not limited by the multivalence of the electron velocity in the flow. This makes it possible to extend the frames of the model performance relative to the moment of the virtual cathode formation and to consider its dynamics. The frequency of electron oscillations in the potential cathode-virtual cathode well is determined on the basis of the above model [ru

  13. Nuclear analytical methods for trace element studies in calcified tissues

    International Nuclear Information System (INIS)

    Chaudhry, M.A.; Chaudhry, M.N.

    2001-01-01

    Full text: Various nuclear analytical methods have been developed and applied to determine the elemental composition of calcified tissues (teeth and bones). Fluorine was determined by prompt gamma activation analysis through the 19 F(p,ag) 16 O reaction. Carbon was measured by activation analysis with He-3 ions, and the technique of Proton-Induced X-ray Emission (PIXE) was applied to simultaneously determine Ca, P, and trace elements in well-documented teeth. Dental hard tissues, enamel, dentine, cement, and their junctions, as well as different parts of the same tissue, were examined separately. Furthermore, using a Proton Microprobe, we measured the surface distribution of F and other elements on and around carious lesions on the enamel. The depth profiles of F, and other elements, were also measured right up to the amelodentin junction

  14. Study of trace elements in milk by nuclear analytical techniques

    International Nuclear Information System (INIS)

    Gharib, A.; Rahimi, H.; Pyrovan, H.; Raoffi, N.J.; Taherpoor, H.

    1985-01-01

    This work is part of project with the IAEA in a coordinated program on 'Trace Elements in Human and Bio-environmental Systems' to evaluate their nutritional requierements, interrelations and the role of trace elements in health, metabolism, etc. Cow's milk is regarded to be one of the most important and most nutritious foodstuffs of mankind. Hence, as a first step, an elemental analysis for milk was carried out: a few samples of pasteurized milk and local samples were investigated for essential and toxic trace elements. The secondary aim of the project was the assessment of various analytical techniques involved. AAS, PIXE and NAA are presented here. The latter was applied both instrumentally and radiochemically. Although the results pertaining to the various methods employed are not in good agreement, there is, however, some justification to clarify this internal inconsistency. PIXE analysis is very fast and rather routine, but the technique for trace element analysis needs certain adaptations and improvement. (author)

  15. A mathematical framework for virtual IMRT QA using machine learning.

    Science.gov (United States)

    Valdes, G; Scheuermann, R; Hung, C Y; Olszanski, A; Bellerive, M; Solberg, T D

    2016-07-01

    It is common practice to perform patient-specific pretreatment verifications to the clinical delivery of IMRT. This process can be time-consuming and not altogether instructive due to the myriad sources that may produce a failing result. The purpose of this study was to develop an algorithm capable of predicting IMRT QA passing rates a priori. From all treatment, 498 IMRT plans sites were planned in eclipse version 11 and delivered using a dynamic sliding window technique on Clinac iX or TrueBeam Linacs. 3%/3 mm local dose/distance-to-agreement (DTA) was recorded using a commercial 2D diode array. Each plan was characterized by 78 metrics that describe different aspects of their complexity that could lead to disagreements between the calculated and measured dose. A Poisson regression with Lasso regularization was trained to learn the relation between the plan characteristics and each passing rate. Passing rates 3%/3 mm local dose/DTA can be predicted with an error smaller than 3% for all plans analyzed. The most important metrics to describe the passing rates were determined to be the MU factor (MU per Gy), small aperture score, irregularity factor, and fraction of the plan delivered at the corners of a 40 × 40 cm field. The higher the value of these metrics, the worse the passing rates. The Virtual QA process predicts IMRT passing rates with a high likelihood, allows the detection of failures due to setup errors, and it is sensitive enough to detect small differences between matched Linacs.

  16. (U) An Analytic Study of Piezoelectric Ejecta Mass Measurements

    Energy Technology Data Exchange (ETDEWEB)

    Tregillis, Ian Lee [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-02-16

    We consider the piezoelectric measurement of the areal mass of an ejecta cloud, for the specific case where ejecta are created by a single shock at the free surface and fly ballistically through vacuum to the sensor. To do so, we define time- and velocity-dependent ejecta “areal mass functions” at the source and sensor in terms of typically unknown distribution functions for the ejecta particles. Next, we derive an equation governing the relationship between the areal mass function at the source (which resides in the rest frame of the free surface) and at the sensor (which resides in the laboratory frame). We also derive expressions for the analytic (“true”) accumulated ejecta mass at the sensor and the measured (“inferred”) value obtained via the standard method for analyzing piezoelectric voltage traces. This approach enables us to derive an exact expression for the error imposed upon a piezoelectric ejecta mass measurement (in a perfect system) by the assumption of instantaneous creation. We verify that when the ejecta are created instantaneously (i.e., when the time dependence is a delta function), the piezoelectric inference method exactly reproduces the correct result. When creation is not instantaneous, the standard piezo analysis will always overestimate the true mass. However, the error is generally quite small (less than several percent) for most reasonable velocity and time dependences. In some cases, errors exceeding 10-15% may require velocity distributions or ejecta production timescales inconsistent with experimental observations. These results are demonstrated rigorously with numerous analytic test problems.

  17. NHEXAS PHASE I ARIZONA STUDY--STANDARD OPERATING PROCEDURE FOR COLLECTION, STORAGE AND SHIPMENT OF URINE SAMPLES FOR SELECTED METALS AND PESTICIDES (UA-F-20.1)

    Science.gov (United States)

    The purpose of this SOP is to guide the collection, storage, and shipment of urine samples collected for the NHEXAS Arizona project. This SOP provides a brief description of sample, collection, preservation, storage, shipping, and custody procedures. This procedure was followed ...

  18. Traditional cultural use as a tool for inferring biogeography and provenance: a case study involving painted turtles (Chrysemys picta) and Hopi Native American culture in Arizona, USA

    Science.gov (United States)

    Lovich, Jeffrey E.; LaRue, Charles T.; Drost, Charles A.; Arundel, Terence R.

    2014-01-01

    Inferring the natural distribution and native status of organisms is complicated by the role of ancient and modern humans in utilization and translocation. Archaeological data and traditional cultural use provide tools for resolving these issues. Although the painted turtle (Chrysemys picta) has a transcontinental range in the United States, populations in the Desert Southwest are scattered and isolated. This pattern may be related to the fragmentation of a more continuous distribution as a result of climate change after the Pleistocene, or translocation by Native Americans who used turtles for food and ceremonial purposes. Because of these conflicting or potentially confounded possibilities, the distribution and status of C. picta as a native species in the state of Arizona has been questioned in the herpetological literature. We present evidence of a population that once occurred in the vicinity of Winslow, Arizona, far from current remnant populations on the upper Little Colorado River. Members of the Native American Hopi tribe are known to have hunted turtles for ceremonial purposes in this area as far back as AD 1290 and possibly earlier. Remains of C. picta are known from several pueblos in the vicinity including Homol'ovi, Awatovi, and Walpi. Given the great age of records for C. picta in Arizona and the concordance of its fragmented and isolated distribution with other reptiles in the region, we conclude that painted turtles are part of the native fauna of Arizona.

  19. Rickettsia parkeri Rickettsiosis, Arizona, USA.

    Science.gov (United States)

    Herrick, Kristen L; Pena, Sandra A; Yaglom, Hayley D; Layton, Brent J; Moors, Amanda; Loftis, Amanda D; Condit, Marah E; Singleton, Joseph; Kato, Cecilia Y; Denison, Amy M; Ng, Dianna; Mertins, James W; Paddock, Christopher D

    2016-05-01

    In the United States, all previously reported cases of Rickettsia parkeri rickettsiosis have been linked to transmission by the Gulf Coast tick (Amblyomma maculatum). Here we describe 1 confirmed and 1 probable case of R. parkeri rickettsiosis acquired in a mountainous region of southern Arizona, well beyond the recognized geographic range of A. maculatum ticks. The likely vector for these 2 infections was identified as the Amblyomma triste tick, a Neotropical species only recently recognized in the United States. Identification of R. parkeri rickettsiosis in southern Arizona demonstrates a need for local ecologic and epidemiologic assessments to better understand geographic distribution and define public health risk. Education and outreach aimed at persons recreating or working in this region of southern Arizona would improve awareness and promote prevention of tickborne rickettsioses.

  20. The Uneven Performance of Arizona's Charter Schools

    Science.gov (United States)

    Chingos, Matthew M.; West, Martin R.

    2015-01-01

    Arizona enrolls a larger share of its students in charter schools than any other state in the country, but no comprehensive examination exists of the impact of those schools on student achievement. Using student-level data covering all Arizona students from 2006 to 2012, we find that the performance of charter schools in Arizona in improving…

  1. Role of QA in total quality management environment

    International Nuclear Information System (INIS)

    McCarthy, J.B.; Ayres, R.A.

    1992-01-01

    A successful company in today's highly competitive business environment must emphasize quality in all activities at all times. For most companies, this requires a major cultural change to establish appropriate operating attitudes and priorities. A total quality environment is required where quality becomes a way of life, and this process must be carefully managed. It will not be accomplished in a few short months with a simple management pronouncement. Instead, it evolves over a period of years through continuous incremental improvement. This evolution towards total quality requires a dramatic change in the quality assurance (QA) function of most companies. Traditionally, quality was automatically equated to QA and its attendant procedures and personnel. Now, quality is becoming a global concept, and QA can play a significant role in the process. The QA profession must, however, recognize and accept a new role as consultant, coach, and partner in today's total quality game. The days of the hard-line enforcer of procedural requirements are gone

  2. Current Status of QA For Nuclear Power Plants in Japan

    International Nuclear Information System (INIS)

    Nagoshi, Hitohiko

    1986-01-01

    It is the current status of QA and our QA experiences with nuclear power plants against the background of the Japanese social and business environment. Accordingly, in 1972, 'The Guidance for Quality Assurance in Construction of Nuclear Power Plants' based on U. S. 10CEF50 Appendix B, was published by the Japan Electric Association. 'Jug-4101 The Guide for Quality Assurance of Nuclear Power Plants' has been prepared by referring to the IAEA QA code. The Guide has been accepted by the Japanese nuclear industry and applied to the QA programs of every organization concerned therewith. The Japanese approach to higher quality will naturally be different from that of other countries because of Japan's cultural, social, and economic conditions. Even higher quality is being aimed at through the LWR Improvement and Standardization Program and coordinated quality assurance efforts

  3. Worldwide QA networks for radiotherapy dosimetry

    International Nuclear Information System (INIS)

    Izewska, J.; Svensson, H.; Ibbott, G.

    2002-01-01

    institutions participating in the U.S. National Cancer Institute's (NCI's) co-operative clinical trials. The RPC currently monitors approximately 1300 centres throughout the USA, Canada and several other countries. The audit tools include, in addition to mailed TLD, review of the institution's dosimetry data, the treatment records of patients entered into trials, and the institution's QA programme. Anthropomorphic phantoms have been developed to evaluate specific treatment techniques. Other currently operating external audit programmes have been either associated with national and international clinical trial groups, similarly to RPC, e.g. EORTC (European Organisation for Research in Treatment of Cancer) in Europe, MRC (Medical Research Council) in the UK, or have been one-off national dosimetry intercomparison exercises, carried out to test various levels of radiotherapy dosimetry, e.g. in Sweden, the Netherlands, Belgium, Switzerland, Australia. Some individual countries have set up comprehensive regular audits of radiotherapy centres, including QA programmes, equipment and dosimetry, e.g. Finland, New Zealand. The IAEA supports its Member States in developing national programmes for TLD based QA audits in radiotherapy dosimetry and whenever possible, establishes links between the national programmes and the IAEA's Dosimetry Laboratory. It disseminates its standardised TLD methodology and provides technical back up to national TLD networks assuring at the same time traceability to primary dosimetry standards. There are several countries (Argentina, Algeria, Brazil, China, Colombia, Cuba, Czech Republic, India, Israel, Malaysia, Philippines, Poland and Vietnam) that have established TLD programmes to audit radiotherapy beams in their countries with assistance of the IAEA. Recently a new IAEA project has been initiated for national TLD audits in non-reference conditions as significant numbers of deviations in non-reference situations, as used clinically on patients, have been

  4. Case study: IBM Watson Analytics cloud platform as Analytics-as-a-Service system for heart failure early detection

    OpenAIRE

    Guidi, Gabriele; Miniati, Roberto; Mazzola, Matteo; Iadanza, Ernesto

    2016-01-01

    In the recent years the progress in technology and the increasing availability of fast connections have produced a migration of functionalities in Information Technologies services, from static servers to distributed technologies. This article describes the main tools available on the market to perform Analytics as a Service (AaaS) using a cloud platform. It is also described a use case of IBM Watson Analytics, a cloud system for data analytics, applied to the following research scope: detect...

  5. Analytic study of 1D diffusive relativistic shock acceleration

    Energy Technology Data Exchange (ETDEWEB)

    Keshet, Uri, E-mail: ukeshet@bgu.ac.il [Physics Department, Ben-Gurion University of the Negev, POB 653, Be' er-Sheva 84105 (Israel)

    2017-10-01

    Diffusive shock acceleration (DSA) by relativistic shocks is thought to generate the dN / dE ∝ E{sup −p} spectra of charged particles in various astronomical relativistic flows. We show that for test particles in one dimension (1D), p {sup −1}=1−ln[γ{sub d}(1+β{sub d})]/ln[γ{sub u}(1+β{sub u})], where β{sub u}(β{sub d}) is the upstream (downstream) normalized velocity, and γ is the respective Lorentz factor. This analytically captures the main properties of relativistic DSA in higher dimensions, with no assumptions on the diffusion mechanism. Unlike 2D and 3D, here the spectrum is sensitive to the equation of state even in the ultra-relativistic limit, and (for a J(üttner-Synge equation of state) noticeably hardens with increasing 1<γ{sub u}<57, before logarithmically converging back to p (γ{sub u→∞})=2. The 1D spectrum is sensitive to drifts, but only in the downstream, and not in the ultra-relativistic limit.

  6. Applications of nuclear analytical techniques to environmental studies

    International Nuclear Information System (INIS)

    Freitas, M.C.; Marques, A.P.; Reis, M.A.; Pacheco, A.M.G.; Barros, L.I.C.

    2001-01-01

    A few examples of application of nuclear-analytical techniques to biological monitors - natives and transplants - are given herein. Parmelia sulcata Taylor transplants were set up in a heavily industrialized area of Portugal - the Setubal peninsula, about 50 km south of Lisbon - where indigenous lichens are rare. The whole area was 10x15 km around an oil-fired power station, and a 2.5x2.5 km grid was used. In north-western Portugal, native thalli of the same epiphytes (Parmelia spp., mostly Parmelia sulcata Taylor) and bark from olive trees (Olea europaea) were sampled across an area of 50x50 km, using a 10x10 km grid. This area is densely populated and features a blend of rural, urban-industrial and coastal environments, together with the country's second-largest metro area (Porto). All biomonitors have been analyzed by INAA and PIXE. Results were put through nonparametric tests and factor analysis for trend significance and emission sources, respectively

  7. Study of trace elements in milk by nuclear analytical techniques

    Energy Technology Data Exchange (ETDEWEB)

    Gharib, A.; Rahimi, H.; Peyrovan, H.; Raofei, H.N.J.; Taherpour, H. (Atomic Energy Organization of Iran, Teheran. Nuclear Research Centre)

    This work is part of a project with the IAEA, in a coordinated programme on ''trace elements in Human Nutrition and Bio-Environmental Systems'' to evaluate their nutritional requirements, interrelations and the role of trace elements in health, metabolism etc. Cow's milk is regarded as one of the most important and nutritious foodstuffs consumed by people. Hence, as a first step, an elemental analysis for milk was carried out for this purpose so a few samples of pasteurized milk and local samples were investigated for essential and toxic trace elements. The secondary aim of this project was the assessment of various analytical techniques involved. However, in the present work, the methods involved were AAS, PIXE and NAA. The latter method applied, both instrumentally and radiochemically. Although the results pertaining to the various methods employed are not in good agreement, there is however, some justification to clarify this internal inconsistency. The precision for NAA and AAS allows greater degree of acceptance respectively. Although PIXE is very fast and rather routine, the technique of trace element analysis needs certain adaptations and developments.

  8. Estimation of eye lens dose during brain scans using Gafchromic XR-QA2 film in various multidetector CT scanners

    International Nuclear Information System (INIS)

    Akhilesh, Philomina; Jamhale, Shramika H.; Sharma, S.D.; Kumar, Rajesh; Datta, D.; Kulkarni, Arti R.

    2017-01-01

    The purpose of this study was to estimate eye lens dose during brain scans in 16-, 64-, 128- and 256-slice multidetector computed tomography (CT) scanners in helical acquisition mode and to test the feasibility of using radiochromic film as eye lens dosemeter during CT scanning. Eye lens dose measurements were performed using Gafchromic XR-QA2 film on a polystyrene head phantom designed with outer dimensions equivalent to the head size of a reference Indian man. The response accuracy of XR-QA2 film was validated by using thermoluminescence dosemeters. The eye lens dose measured using XR-QA2 film on head phantom for plain brain scanning in helical mode ranged from 43.8 to 45.8 mGy. The XR-QA2 film measured dose values were in agreement with TLD measured dose values within a maximum variation of 8.9%. The good correlation between the two data sets confirms the viability of using XR-QA2 film for eye lens dosimetry. (authors)

  9. SU-G-TeP2-01: Can EPID Based Measurement Replace Traditional Daily Output QA On Megavoltage Linac?

    International Nuclear Information System (INIS)

    Saleh, Z; Tang, X; Song, Y; Obcemea, C; Beeban, N; Chan, M; Li, X; Tang, G; Lim, S; Lovelock, D; LoSasso, T; Mechalakos, J; Both, S

    2016-01-01

    Purpose: To investigate the long term stability and viability of using EPID-based daily output QA via in-house and vendor driven protocol, to replace conventional QA tools and improve QA efficiency. Methods: Two Varian TrueBeam machines (TB1&TB2) equipped with electronic portal imaging devices (EPID) were employed in this study. Both machines were calibrated per TG-51 and used clinically since Oct 2014. Daily output measurement for 6/15 MV beams were obtained using SunNuclear DailyQA3 device as part of morning QA. In addition, in-house protocol was implemented for EPID output measurement (10×10 cm fields, 100 MU, 100cm SID, output defined over an ROI of 2×2 cm around central axis). Moreover, the Varian Machine Performance Check (MPC) was used on both machines to measure machine output. The EPID and DailyQA3 based measurements of the relative machine output were compared and cross-correlated with monthly machine output as measured by an A12 Exradin 0.65cc Ion Chamber (IC) serving as ground truth. The results were correlated using Pearson test. Results: The correlations among DailyQA3, in-house EPID and Varian MPC output measurements, with the IC for 6/15 MV were similar for TB1 (0.83–0.95) and TB2 (0.55–0.67). The machine output for the 6/15MV beams on both machines showed a similar trend, namely an increase over time as indicated by all measurements, requiring a machine recalibration after 6 months. This drift is due to a known issue with pressurized monitor chamber which tends to leak over time. MPC failed occasionally but passed when repeated. Conclusion: The results indicate that the use of EPID for daily output measurements has the potential to become a viable and efficient tool for daily routine LINAC QA, thus eliminating weather (T,P) and human setup variability and increasing efficiency of the QA process.

  10. SU-G-TeP2-01: Can EPID Based Measurement Replace Traditional Daily Output QA On Megavoltage Linac?

    Energy Technology Data Exchange (ETDEWEB)

    Saleh, Z; Tang, X; Song, Y; Obcemea, C; Beeban, N; Chan, M; Li, X; Tang, G; Lim, S; Lovelock, D; LoSasso, T; Mechalakos, J; Both, S [Memorial Sloan-Kettering Cancer Center, NY (United States)

    2016-06-15

    Purpose: To investigate the long term stability and viability of using EPID-based daily output QA via in-house and vendor driven protocol, to replace conventional QA tools and improve QA efficiency. Methods: Two Varian TrueBeam machines (TB1&TB2) equipped with electronic portal imaging devices (EPID) were employed in this study. Both machines were calibrated per TG-51 and used clinically since Oct 2014. Daily output measurement for 6/15 MV beams were obtained using SunNuclear DailyQA3 device as part of morning QA. In addition, in-house protocol was implemented for EPID output measurement (10×10 cm fields, 100 MU, 100cm SID, output defined over an ROI of 2×2 cm around central axis). Moreover, the Varian Machine Performance Check (MPC) was used on both machines to measure machine output. The EPID and DailyQA3 based measurements of the relative machine output were compared and cross-correlated with monthly machine output as measured by an A12 Exradin 0.65cc Ion Chamber (IC) serving as ground truth. The results were correlated using Pearson test. Results: The correlations among DailyQA3, in-house EPID and Varian MPC output measurements, with the IC for 6/15 MV were similar for TB1 (0.83–0.95) and TB2 (0.55–0.67). The machine output for the 6/15MV beams on both machines showed a similar trend, namely an increase over time as indicated by all measurements, requiring a machine recalibration after 6 months. This drift is due to a known issue with pressurized monitor chamber which tends to leak over time. MPC failed occasionally but passed when repeated. Conclusion: The results indicate that the use of EPID for daily output measurements has the potential to become a viable and efficient tool for daily routine LINAC QA, thus eliminating weather (T,P) and human setup variability and increasing efficiency of the QA process.

  11. Flexner 2.0—Longitudinal Study of Student Participation in a Campus-Wide General Pathology Course for Graduate Students at The University of Arizona

    Directory of Open Access Journals (Sweden)

    Margaret M. Briehl PhD

    2016-12-01

    Full Text Available Faculty members from the Department of Pathology at The University of Arizona College of Medicine-Tucson have offered a 4-credit course on enhanced general pathology for graduate students since 1996. The course is titled, “Mechanisms of Human Disease.” Between 1997 and 2016, 270 graduate students completed Mechanisms of Human Disease. The students came from 21 programs of study. Analysis of Variance, using course grade as the dependent and degree, program, gender, and year (1997-2016 as independent variables, indicated that there was no significant difference in final grade (F = 0.112; P = .8856 as a function of degree (doctorate: mean = 89.60, standard deviation = 5.75; master’s: mean = 89.34, standard deviation = 6.00; certificate program: mean = 88.64, standard deviation = 8.25, specific type of degree program (F = 2.066, P = .1316; life sciences: mean = 89.95, standard deviation = 6.40; pharmaceutical sciences: mean = 90.71, standard deviation = 4.57; physical sciences: mean = 87.79, standard deviation = 5.17, or as a function of gender (F = 2.96, P = .0865; males: mean = 88.09, standard deviation = 8.36; females: mean = 89.58, standard deviation = 5.82. Students in the physical and life sciences performed equally well. Mechanisms of Human Disease is a popular course that provides students enrolled in a variety of graduate programs with a medical school-based course on mechanisms of diseases. The addition of 2 new medically oriented Master of Science degree programs has nearly tripled enrollment. This graduate level course also potentially expands the interdisciplinary diversity of participants in our interprofessional education and collaborative practice exercises.

  12. SU-F-T-558: ArcCheck for Patient Specific QA in Stereotactic Ablative Radiotherapy

    International Nuclear Information System (INIS)

    Ramachandran, P; Tajaldeen, A; Esen, N; Geso, M; Taylor, D; Wanigaratne, D; Roozen, K; Kron, T

    2016-01-01

    Purpose: Stereotactic Ablative Radiotherapy (SABR) is one of the most preferred treatment techniques for early stage lung cancer. This technique has been extended to other treatment sites like Spine, Liver, Scapula, Sternum etc., This has resulted in increased physics QA time on machine. In this study, we’ve tested the feasibility of using ArcCheck as an alternative method to replace film dosimetry. Methods: Twelve patients with varied diagnosis of Lung, Liver, scapula, sternum and Spine undergoing SABR were selected for this study. Pre-treatment QA was performed for all the patients which include ionization chamber and film dosimetry. The required gamma criteria for each SABR plan to pass QA and proceed to treatment is 95% (3%,1mm). In addition to this routine process, the treatment plans were exported on to an ArcCheck phantom. The planned and measured dose from the ArcCheck device were compared using four different gamma criteria: 2%,2 mm, 3%,2 mm, 3%,1 mm and 3%, 3 mm. In addition to this, we’ve also introduced errors to gantry, collimator and couch angle to assess sensitivity of the ArcCheck with potential delivery errors. Results: The ArcCheck mean passing rates for all twelve cases were 76.1%±9.7% for gamma criteria 3%,1 mm, 89.5%±5.3% for 2%,2 mm, 92.6%±4.2% for 3%,2 mm, and 97.6%±2.4% for 3%,3 mm gamma criteria. When SABR spine cases are excluded, we observe ArcCheck passing rates higher than 95% for all the studied cases with 3%, 3mm, and ArcCheck results in acceptable agreement with the film gamma results. Conclusion: Our ArcCheck results at 3%, 3 mm were found to correlate well with our non-SABR spine routine patient specific QA results (3%,1 mm). We observed significant reduction in QA time on using ArcCheck for SABR QA. This study shows that ArcCheck could replace film dosimetry for all sites except SABR spine.

  13. SU-F-T-558: ArcCheck for Patient Specific QA in Stereotactic Ablative Radiotherapy

    Energy Technology Data Exchange (ETDEWEB)

    Ramachandran, P [Peter MacCallum Cancer Centre, Melbourne (Australia); RMIT University, Bundoora (Australia); Tajaldeen, A; Esen, N; Geso, M [RMIT University, Bundoora (Australia); Taylor, D; Wanigaratne, D; Roozen, K; Kron, T [Peter MacCallum Cancer Centre, Melbourne (Australia)

    2016-06-15

    Purpose: Stereotactic Ablative Radiotherapy (SABR) is one of the most preferred treatment techniques for early stage lung cancer. This technique has been extended to other treatment sites like Spine, Liver, Scapula, Sternum etc., This has resulted in increased physics QA time on machine. In this study, we’ve tested the feasibility of using ArcCheck as an alternative method to replace film dosimetry. Methods: Twelve patients with varied diagnosis of Lung, Liver, scapula, sternum and Spine undergoing SABR were selected for this study. Pre-treatment QA was performed for all the patients which include ionization chamber and film dosimetry. The required gamma criteria for each SABR plan to pass QA and proceed to treatment is 95% (3%,1mm). In addition to this routine process, the treatment plans were exported on to an ArcCheck phantom. The planned and measured dose from the ArcCheck device were compared using four different gamma criteria: 2%,2 mm, 3%,2 mm, 3%,1 mm and 3%, 3 mm. In addition to this, we’ve also introduced errors to gantry, collimator and couch angle to assess sensitivity of the ArcCheck with potential delivery errors. Results: The ArcCheck mean passing rates for all twelve cases were 76.1%±9.7% for gamma criteria 3%,1 mm, 89.5%±5.3% for 2%,2 mm, 92.6%±4.2% for 3%,2 mm, and 97.6%±2.4% for 3%,3 mm gamma criteria. When SABR spine cases are excluded, we observe ArcCheck passing rates higher than 95% for all the studied cases with 3%, 3mm, and ArcCheck results in acceptable agreement with the film gamma results. Conclusion: Our ArcCheck results at 3%, 3 mm were found to correlate well with our non-SABR spine routine patient specific QA results (3%,1 mm). We observed significant reduction in QA time on using ArcCheck for SABR QA. This study shows that ArcCheck could replace film dosimetry for all sites except SABR spine.

  14. QA role in advanced energy activities: Reductionism, emergence, and functionalism; presuppositions in designing internal QA audits

    Energy Technology Data Exchange (ETDEWEB)

    Bodnarczuk, M.

    1988-06-01

    After a brief overview of the mission of Fermilab, this paper explores some of the problems associated with designing internal QA audits. The paper begins with several examples of how audits should not be designed, then goes on to analyze two types of presuppositions about organizational structure (reductionism and emergence) that can be misleading and skew the data sample if folded too heavily into the checklist. A third type of presupposition (functionalism), is proposed as a viable way of achieving a more well-rounded measure of the performance of an organization, i.e. its effectiveness, not just compliance.

  15. The analytical and numerical study of the fluorination of uranium dioxide particles

    International Nuclear Information System (INIS)

    Sazhin, S.S.

    1997-01-01

    A detailed analytical study of the equations describing the fluorination of UO 2 particles is presented for some limiting cases assuming that the mass flowrate of these particles is so small that they do not affect the state of the gas. The analytical solutions obtained can be used for approximate estimates of the effect of fluorination on particle diameter and temperature but their major application, however, is probably in the verification of self-consistent numerical solutions. Computational results are presented and discussed for a self-consistent problem in which both the effects of gas on particles and particles on gas are accounted for. It has been shown that in the limiting cases for which analytical solutions have been obtained, the coincidence between numerical and analytical results is almost exact. This can be considered as a verification of both the analytical and numerical solutions. (orig.)

  16. Argumentation in Miranda v. Arizona.

    Science.gov (United States)

    Benoit, William L.

    1991-01-01

    Investigates the argumentation advanced in briefs, oral arguments, and the Supreme Court's opinion in the case of Miranda versus Arizona. Considers the background of the case, analyzes the argumentation and its influences on the court, and stresses the importance of viewing the Supreme Court as an active participant in the decision-making process.…

  17. Boots on the Ground: Arizona

    Centers for Disease Control (CDC) Podcasts

    2013-12-26

    In this podcast, we talk to CDC public health advisor Lisa Speissegger about her response efforts during the 2013 Arizona wildfires.  Created: 12/26/2013 by Office of Public Health Preparedness and Response (PHPR).   Date Released: 12/26/2013.

  18. Residential Energy Efficiency Potential: Arizona

    Energy Technology Data Exchange (ETDEWEB)

    Wilson, Eric J [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-11-16

    Energy used by Arizona single-family homes that can be saved through cost-effective improvements. Prepared by Eric Wilson and Noel Merket, NREL, and Erin Boyd, U.S. Department of Energy Office of Energy Policy and Systems Analysis.

  19. A Melioidosis Case in Arizona

    Centers for Disease Control (CDC) Podcasts

    2011-10-03

    David Blaney, Medical Officer, Bacterial Special Pathogens Branch, discusses an unusual melioidosis case in Arizona.  Created: 10/3/2011 by National Center for Emerging Zoonotic and Infectious Diseases (NCEZID).   Date Released: 10/5/2011.

  20. Arizona TeleMedicine Project.

    Science.gov (United States)

    Arizona Univ., Tucson. Coll. of Medicine.

    Designed to provide health services for American Indians living on rurally isolated reservations, the Arizona TeleMedicine Project proposes to link Phoenix and Tucson medical centers, via a statewide telecommunications system, with the Hopi, San Carlos Apache, Papago, Navajo, and White Mountain Apache reservations. Advisory boards are being…

  1. Consequences of Arizona's Immigration Policy on Social Capital among Mexican Mothers with Unauthorized Immigration Status

    Science.gov (United States)

    Valdez, Carmen R.; Padilla, Brian; Valentine, Jessa Lewis

    2013-01-01

    This study explores the consequences of increasingly restrictive immigration policies on social capital among Mexican mothers with unauthorized immigrant status in Arizona. Three focus groups conducted in Arizona explore how mothers' experiences with immigration policies have affected their neighborhood, community, and family ties. Focus group…

  2. The Invisible Revolving Door: The Issue of Teacher Attrition in English Language Development Classrooms in Arizona

    Science.gov (United States)

    Heineke, Amy J.

    2018-01-01

    The most restrictive language policy context in the United States, Arizona's monolingual and prescriptive approach to teaching English learners continues to capture national and international attention. Five school years removed from the initial implementation, this study aimed to understand the complexities of Arizona language policy in…

  3. An Autosomal Factor from Drosophila Arizonae Restores Normal Spermatogenesis in Drosophila Mojavensis Males Carrying the D. Arizonae Y Chromosome

    Science.gov (United States)

    Pantazidis, A. C.; Galanopoulos, V. K.; Zouros, E.

    1993-01-01

    Males of Drosophila mojavensis whose Y chromosome is replaced by the Y chromosome of the sibling species Drosophila arizonae are sterile. It is shown that genetic material from the fourth chromosome of D. arizonae is necessary and sufficient, in single dose, to restore fertility in these males. In introgression and mapping experiments this material segregates as a single Mendelian factor (sperm motility factor, SMF). Light and electron microscopy studies of spermatogenesis in D. mojavensis males whose Y chromosome is replaced by introgression with the Y chromosome of D. arizonae (these males are symbolized as mojY(a)) revealed postmeiotic abnormalities all of which are restored when the SMF of D. arizonae is co-introgressed (these males are symbolized as mojY(a)SMF(a)). The number of mature sperm per bundle in mojY(a)SMF(a) is slightly less than in pure D. mojavensis and is even smaller in males whose fertility is rescued by introgression of the entire fourth chromosome of D. arizonae. These observations establish an interspecific incompatibility between the Y chromosome and an autosomal factor (or more than one tightly linked factors) that can be useful for the study of the evolution of male hybrid sterility in Drosophila and the genetic control of spermatogenesis. PMID:8514139

  4. Examining the Use of a Visual Analytics System for Sensemaking Tasks: Case Studies with Domain Experts.

    Science.gov (United States)

    Kang, Youn-Ah; Stasko, J

    2012-12-01

    While the formal evaluation of systems in visual analytics is still relatively uncommon, particularly rare are case studies of prolonged system use by domain analysts working with their own data. Conducting case studies can be challenging, but it can be a particularly effective way to examine whether visual analytics systems are truly helping expert users to accomplish their goals. We studied the use of a visual analytics system for sensemaking tasks on documents by six analysts from a variety of domains. We describe their application of the system along with the benefits, issues, and problems that we uncovered. Findings from the studies identify features that visual analytics systems should emphasize as well as missing capabilities that should be addressed. These findings inform design implications for future systems.

  5. Analytical Study on Thermal and Mechanical Design of Printed Circuit Heat Exchanger

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Su-Jong [Idaho National Lab. (INL), Idaho Falls, ID (United States); Sabharwall, Piyush [Idaho National Lab. (INL), Idaho Falls, ID (United States); Kim, Eung-Soo [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2013-09-01

    The analytical methodologies for the thermal design, mechanical design and cost estimation of printed circuit heat exchanger are presented in this study. In this study, three flow arrangements of parallel flow, countercurrent flow and crossflow are taken into account. For each flow arrangement, the analytical solution of temperature profile of heat exchanger is introduced. The size and cost of printed circuit heat exchangers for advanced small modular reactors, which employ various coolants such as sodium, molten salts, helium, and water, are also presented.

  6. A meteorological study of parks and timbered areas in the western yellow-pine forests of Arizona and New Mexico

    Science.gov (United States)

    G. A. Pearson

    1913-01-01

    The object of the study, the results of which are presented here, was to determine the influence of the forest cover upon climate locally in the Southwest, in so far as this influence might be of importance in the management of timberlands and the possible afforestation of parks and denuded areas. Since the bearing upon forestry rather than upon meteorology is the...

  7. SU-E-T-392: Evaluation of Ion Chamber/film and Log File Based QA to Detect Delivery Errors

    International Nuclear Information System (INIS)

    Nelson, C; Mason, B; Kirsner, S; Ohrt, J

    2015-01-01

    Purpose: Ion chamber and film (ICAF) is a method used to verify patient dose prior to treatment. More recently, log file based QA has been shown as an alternative for measurement based QA. In this study, we delivered VMAT plans with and without errors to determine if ICAF and/or log file based QA was able to detect the errors. Methods: Using two VMAT patients, the original treatment plan plus 7 additional plans with delivery errors introduced were generated and delivered. The erroneous plans had gantry, collimator, MLC, gantry and collimator, collimator and MLC, MLC and gantry, and gantry, collimator, and MLC errors. The gantry and collimator errors were off by 4 0 for one of the two arcs. The MLC error introduced was one in which the opening aperture didn’t move throughout the delivery of the field. For each delivery, an ICAF measurement was made as well as a dose comparison based upon log files. Passing criteria to evaluate the plans were ion chamber less and 5% and film 90% of pixels pass the 3mm/3% gamma analysis(GA). For log file analysis 90% of voxels pass the 3mm/3% 3D GA and beam parameters match what was in the plan. Results: Two original plans were delivered and passed both ICAF and log file base QA. Both ICAF and log file QA met the dosimetry criteria on 4 of the 12 erroneous cases analyzed (2 cases were not analyzed). For the log file analysis, all 12 erroneous plans alerted a mismatch in delivery versus what was planned. The 8 plans that didn’t meet criteria all had MLC errors. Conclusion: Our study demonstrates that log file based pre-treatment QA was able to detect small errors that may not be detected using an ICAF and both methods of were able to detect larger delivery errors

  8. A Factor Analytic Study of the Teaching Events Stress Inventory.

    Science.gov (United States)

    Alexander, Livingston; And Others

    The purpose of this study was to determine if definitive factors emerge from the responses of teachers to the Teaching Events Stress Inventory (TESI). In a series of three studies during the years 1980 to 1982, data were collected to assess the levels and sources of stress experienced by 660 teachers in central and western Kentucky. The subjects…

  9. A Factor Analytic Study of the Internet Usage Scale

    Science.gov (United States)

    Monetti, David M.; Whatley, Mark A.; Hinkle, Kerry T.; Cunningham, Kerry T.; Breneiser, Jennifer E.; Kisling, Rhea

    2011-01-01

    This study developed an Internet Usage Scale (IUS) for use with adolescent populations. The IUS is a 26-item scale that measures participants' beliefs about how their Internet usage impacts their behavior. The sample for this study consisted of 947 middle school students. An exploratory factor analysis with varimax rotation was conducted on the…

  10. National uranium resource evaluation: Nogales Quadrangle, Arizona

    International Nuclear Information System (INIS)

    Luning, R.H.; Brouillard, L.A.

    1982-04-01

    Literature research, surface geologic investigations, rock sampling, and radiometric surveys were conducted in the Nogales Quadrangle, Arizona, to identify environments and to delineate areas favorable for uranium deposits according to criteria formulated during the National Uranium Resource Evaluation program. The studies were augmented by aerial radiometric and hydrogeochemical and stream-sediment surveys. No favorable environments were identified. Environments that do display favorable characteristics include magmatic-hydrothermal and authigenic environments in Precambrian and Jurassic intrusives, as well as in certain Mesozoic and Cenozoic igneous and sedimentary rocks

  11. Intensity-modulated radiation therapy: dynamic MLC (DMLC) therapy, multisegment therapy and tomotherapy. An example of QA in DMLC therapy

    International Nuclear Information System (INIS)

    Webb, S.

    1998-01-01

    Intensity-modulated radiation therapy will make a quantum leap in tumor control. It is the new radiation therapy for the new millennium. The major methods to achieve IMRT are: 1. Dynamic multileaf collimator (DMLC) therapy, 2. multisegment therapy, and 3. tomotherapy. The principles of these 3 techniques are briefly reviewed. Each technique presents unique QA issues which are outlined. As an example this paper will present the results of a recent new study of an important QA concern in DMLC therapy. (orig.) [de

  12. Minorities in Islamic History: An Analytical Study of Four Documents ...

    African Journals Online (AJOL)

    Journal for Islamic Studies. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 20 (2000) >. Log in or Register to get access to full text downloads.

  13. Experimental and Analytical Studies of Solar System Chemistry

    Science.gov (United States)

    Burnett, Donald S.

    2003-01-01

    The cosmochemistry research funded by this grant resulted in the publications given in the attached Publication List. The research focused in three areas: (1) Experimental studies of trace element partitioning. (2) Studies of the minor element chemistry and O isotopic compositions of MgAlO4 spinels from Ca-Al-Rich Inclusions in carbonaceous chondrite meteorites, and (3) The abundances and chemical fractionations of Th and U in chondritic meteorites.

  14. Analytical studies on the gum exudate from Anogeissus leiocarpus

    International Nuclear Information System (INIS)

    Ahmed, Samia Eltayeb

    1999-04-01

    Anogeissus leiocarpus gum samples were collected as natural exudate nodules, from three different location. Physicochemical properties of gum samples were studied. results showed significant differences within each location in most parameters studied except refractive index value which was found to be constant in all samples. The effect of location on the properties of gum samples was also studied and the analysis of variance showed insignificant differences (P≤0.05) in all properties studied except in ash content. Inter nodule variations of gum from two different location were studied individually. Results showed significant differences for each parameter studied except for the refractive index value. The properties studied of all gum samples were as follows: 9.2% moisture, 3.4% ash, 0.72% nitrogen, 4.74% protein, -35.5 specific rotation, 1.68 relative viscosity, 4.2 pH, 1.334 refractive index, 14.3 uronic acid, 0.44% reducing sugar, 1336.0 equivalent weight and 0.68% tannin content. UV absorption spectra of gum samples and gum nodules were determined. Cationic composition of gum samples was also determined and the results showed that (Mg) has highest value in all samples studied followed by Fe, Na, K, Ca, Zn and trace amount of Mn, Co, Ni, Cd and Pb. The water holding capacity was found to be 65.5% and emulsifying stability was found to be 1.008. The component sugars of gum were examined by different methods followed by qualitative and quantitative analysis. Analysis of hydrolysate crude gum sample by HPLC show L-rhamnose (6.82), L-arabinose (48.08), D-galactose (11.26) and two unknown oligosaccharides having values (0.22 and 32.61). Some physicochemical properties were studied. Results showed significant differences in nitrogen and protein contents, specific rotation, relative viscosity, equivalent weight and pH of fractions, where as insignificant differences were observed in uronic acid content and refractive index values

  15. Student Satisfaction in Higher Education: A Meta-Analytic Study

    Science.gov (United States)

    Santini, Fernando de Oliveira; Ladeira, Wagner Junior; Sampaio, Claudio Hoffmann; da Silva Costa, Gustavo

    2017-01-01

    This paper discusses the results of a meta-analysis performed to identify key antecedent and consequent constructs of satisfaction in higher education. We offer an integrated model to achieve a better understanding of satisfaction in the context of higher education. To accomplish this objective, we identified 83 studies that were valid and…

  16. A Study of Online Exams Procrastination Using Data Analytics Techniques

    Science.gov (United States)

    Levy, Yair; Ramim, Michelle M.

    2012-01-01

    Procrastination appears to be an inevitable part of daily life, especially for activities that are bounded by deadlines. It has implications for performance and is known to be linked to poor personal time management. Although research related to procrastination as a general behavior has been well established, studies assessing procrastination in…

  17. Assessing Vocal Performances Using Analytical Assessment: A Case Study

    Science.gov (United States)

    Gynnild, Vidar

    2016-01-01

    This study investigated ways to improve the appraisal of vocal performances within a national academy of music. Since a criterion-based assessment framework had already been adopted, the conceptual foundation of an assessment rubric was used as a guide in an action research project. The group of teachers involved wanted to explore thinking…

  18. Analytical techniques for the study of polyphenol-protein interactions.

    Science.gov (United States)

    Poklar Ulrih, Nataša

    2017-07-03

    This mini review focuses on advances in biophysical techniques to study polyphenol interactions with proteins. Polyphenols have many beneficial pharmacological properties, as a result of which they have been the subject of intensive studies. The most conventional techniques described here can be divided into three groups: (i) methods used for screening (in-situ methods); (ii) methods used to gain insight into the mechanisms of polyphenol-protein interactions; and (iii) methods used to study protein aggregation and precipitation. All of these methods used to study polyphenol-protein interactions are based on modifications to the physicochemical properties of the polyphenols or proteins after binding/complex formation in solution. To date, numerous review articles have been published in the field of polyphenols. This review will give a brief insight in computational methods and biosensors and cell-based methods, spectroscopic methods including fluorescence emission, UV-vis adsorption, circular dichroism, Fourier transform infrared and mass spectrometry, nuclear magnetic resonance, X-ray diffraction, and light scattering techniques including small-angle X-ray scattering and small-angle neutron scattering, and calorimetric techniques (isothermal titration calorimetry and differential scanning calorimetry), microscopy, the techniques which have been successfully used for polyphenol-protein interactions. At the end the new methods based on single molecule detection with high potential to study polyphenol-protein interactions will be presented. The advantages and disadvantages of each technique will be discussed as well as the thermodynamic, kinetic or structural parameters, which can be obtained. The other relevant biophysical experimental techniques that have proven to be valuable, such electrochemical methods, hydrodynamic techniques and chromatographic techniques will not be described here.

  19. Analytical, Experimental, and Modelling Studies of Lunar and Terrestrial Rocks

    Science.gov (United States)

    Haskin, Larry A.

    1997-01-01

    The goal of our research has been to understand the paths and the processes of planetary evolution that produced planetary surface materials as we find them. Most of our work has been on lunar materials and processes. We have done studies that obtain geological knowledge from detailed examination of regolith materials and we have reported implications for future sample-collecting and on-surface robotic sensing missions. Our approach has been to study a suite of materials that we have chosen in order to answer specific geologic questions. We continue this work under NAG5-4172. The foundation of our work has been the study of materials with precise chemical and petrographic analyses, emphasizing analysis for trace chemical elements. We have used quantitative models as tests to account for the chemical compositions and mineralogical properties of the materials in terms of regolith processes and igneous processes. We have done experiments as needed to provide values for geochemical parameters used in the models. Our models take explicitly into account the physical as well as the chemical processes that produced or modified the materials. Our approach to planetary geoscience owes much to our experience in terrestrial geoscience, where samples can be collected in field context and sampling sites revisited if necessary. Through studies of terrestrial analog materials, we have tested our ideas about the origins of lunar materials. We have been mainly concerned with the materials of the lunar highland regolith, their properties, their modes of origin, their provenance, and how to extrapolate from their characteristics to learn about the origin and evolution of the Moon's early igneous crust. From this work a modified model for the Moon's structure and evolution is emerging, one of globally asymmetric differentiation of the crust and mantle to produce a crust consisting mainly of ferroan and magnesian igneous rocks containing on average 70-80% plagioclase, with a large

  20. Analytic study of organic matters in Lodeve uranium ore

    International Nuclear Information System (INIS)

    Campuzano, E.J.

    1981-01-01

    Exploitation of uranium in the Permian basin of Lodeve is difficult because of simultaneous extraction of organic matters which are found, in small proportion, in ammonium diuranate and a supplementary purification is required. Available information on natural organic matters are briefly reviewed. Natural organic matters contained in the Lodeve uranium ore processing fluid is separated and fractionated. Physicochemical properties of ligands in each fraction are studied. The existence of bonds between these ligands and dissolved uranium is experimentally demonstrated [fr

  1. ANALYTICAL REVIEW OF ELECTRONIC RESOURCES FOR THE STUDY OF LATIN

    Directory of Open Access Journals (Sweden)

    Olena Yu. Balalaieva

    2014-04-01

    Full Text Available The article investigates the current state of development of e-learning content in the Latin language. It is noted that the introduction of ICT in the educational space has expanded the possibility of studying Latin, opened access to digital libraries resources, made it possible to use scientific and educational potential and teaching Latin best practices of world's leading universities. A review of foreign and Ukrainian information resources and electronic editions for the study of Latin is given. Much attention was paid to the didactic potential of local and online multimedia courses of Latin, electronic textbooks, workbooks of interactive tests and exercises, various dictionaries and software translators, databases and digital libraries. Based on analysis of the world market of educational services and products the main trends in the development of information resources and electronic books are examined. It was found that multimedia courses with interactive exercises or workbooks with interactive tests, online dictionaries and translators are the most widely represented and demanded. The noticeable lagging of Ukrainian education and computer linguistics in quantitative and qualitative measures in this industry is established. The obvious drawback of existing Ukrainian resources and electronic editions for the study of Latin is their noninteractive nature. The prospects of e-learning content in Latin in Ukraine are outlined.

  2. AN ANALYTICAL STUDY OF DEATHS DUE TO POISONING IN VISAKHAPATNAM

    Directory of Open Access Journals (Sweden)

    V. Chandrasekhar

    2017-11-01

    Full Text Available BACKGROUND The aim of this study was to determine and classify the various types of poisoning deaths as seen at Andhra Medical College Mortuary, Visakhapatnam city. MATERIALS AND METHODS This is a retrospective study of all the deaths due to poisoning seen in the Department of Forensic Medicine & Toxicology, Andhra Medical College, Visakhapatnam City over a 15 year period (January 2001‐December 2015 as recorded in the autopsy registers and postmortem reports of the department. RESULTS Poisoning is one of the commonest methods of committing suicide especially in developing countries like India. A total of 22475 autopsies were done during the period. Two thousand seventy four cases representing 9.23% of all bodies received by the mortuary were deaths due to poisoning. Organophosphate compounds were the most commonly 78.98% abused substance. The common motive of poisoning was suicidal 93.43%with male to female ratio 6.69:1.Peak incidence was observed in the age group 21-40 years. Type of poison consumed, socioeconomic status and place of household are also ascertained. CONCLUSION This study shows the pattern of poisoning deaths in Visakhapatnam and this preliminary data will provide a baseline for future research and help in formulating policies to prevent deaths due to poisoning.

  3. [Psychotic parricide: clinical and analytic study of 16 cases].

    Science.gov (United States)

    Dakhlaoui, Olfa; Khémiri, Omar; Gaha, Nesrine; Ridha, Rym; Haffani, Fakhreddine

    2009-12-01

    The parricide is defined as "murder of the father or the mother or any other legitimate ascendant." It represents 1 to 5% of all homicides and 20 to 30% of psychotic homicides. In Tunisia, few studies have focused on this issue. We propose in this work to describe the profile of psychotic parricide. We tried to identify risk factors in order to prevent this acting out. Our study is retrospective we observed 16 male patients diagnosed with schizophrenia hospitalized between June 1979 and March 2008 in the forensic psychiatry department at the psychiatric hospital in Tunis, discharged for no ground for prosecution following parricide. They accounted for 20.8% of psychotic homicides hospitalized during the same period (16/77) and approximately 30% of homicides committed by schizophrenic patients. We found as many as patricide as matricide. The main factors that have emerged through our study are an early age (28 years), being single (70%), the socio-cultural poverty, unemployment, paranoid delusions, hallucinations and recent treatment interruption. All these factors have been cited by many authors including Millaud et al, they also cited history of violence and violent behavior and alcohol or drug abuse. One important point is that some signs of this imminent gesture are often present but misunderstood, such a sense of situational impasse, a request for help, or reluctance during interview. It is essential to identify risk factors, even to actively seek some warning signs, which often are not spontaneously reported by the psychotic patient. Hospitalization under constraint in psychiatry should be the appropriate response if these dangerousness signals are noticed by the psychiatrist.

  4. Indian Kisan Credit Card Scheme: An Analytical Study

    Directory of Open Access Journals (Sweden)

    Dharmendra Mehta

    2016-03-01

    Full Text Available Kisan Credit Card (KCC has now been regarded as the only medium of short-term credit for agriculture. The Kisan Credit Card (KCC scheme was introduced by the Finance Minister in his budget speech in the year 1998-99. From the year 1998-99, the scheme was implemented by public sector commercial banks, RRBs (Regional Rural Banks and cooperative banks in the country. It has emerged as an innovative credit distribution system to meet the production credit requirements of the farmers in a timely and easy manner. The present paper is aimed to study role of Kisan Credit Card in the rural credit facilitation in India.

  5. Analytic study of SU(3) lattice gauge theory

    International Nuclear Information System (INIS)

    Zheng Xite; Xu Yong

    1989-01-01

    The variational-cumulant expansion method has been extended to the case of lattice SU(3) Wilson model. The plaquette energy as an order paramenter has been calculated to the 2nd order expansion. No 1st order phase transition in the D = 4 case is found which is in agreement with the monte Carlo results, and the 1st order phase transition in the d = 5 case is clearly seen. The method can be used in the study of problems in LGT with SU(3) gauge group

  6. Study of potential applications of compact ECRIS to analytical system

    International Nuclear Information System (INIS)

    Kidera, M.; Takahashi, K.; Seto, Y.; Kishi, S.; Enomoto, S.; Nagamatsu, T.; Tanaka, T.

    2012-01-01

    The objective of this study is to develop a desktop-sized system of element mass analysis (element analysis system) with a compact electron cyclotron resonance (ECR) ion source in the ionization section. This system is different from other element analysis systems in terms of the effective use of ionization by ECR plasma. A compact ECR ion source is required to fit in the desktop-sized element analysis system. This paper reporting the development of the compact ECR ion source, is followed by the associated poster. (authors)

  7. Photocatalytic degradation of rosuvastatin: Analytical studies and toxicity evaluations

    Energy Technology Data Exchange (ETDEWEB)

    Machado, Tiele Caprioli, E-mail: tiele@enq.ufrgs.br [Chemical Engineering Department, Federal University of Rio Grande do Sul, Rua Engenheiro Luiz Englert s/n, CEP: 90040-040 Porto Alegre, RS (Brazil); Pizzolato, Tânia Mara [Chemical Institute, Federal University of Rio Grande do Sul, Avenida Bento Gonçalves, 9500, CEP: 91501-970 Porto Alegre, RS (Brazil); Arenzon, Alexandre [Ecology Center, Federal University of Rio Grande do Sul, Avenida Bento Gonçalves, 9500, CEP: 91501-970 Porto Alegre, RS (Brazil); Segalin, Jeferson [Biotechnology Center, Federal University of Rio Grande do Sul, Avenida Bento Gonçalves, 9500, CEP: 91501-970 Porto Alegre, RS (Brazil); Lansarin, Marla Azário [Chemical Engineering Department, Federal University of Rio Grande do Sul, Rua Engenheiro Luiz Englert s/n, CEP: 90040-040 Porto Alegre, RS (Brazil)

    2015-01-01

    Photocatalytic degradation of rosuvastatin, which is a drug that has been used to reduce blood cholesterol levels, was studied in this work employing ZnO as catalyst. The experiments were carried out in a temperature-controlled batch reactor that was irradiated with UV light. Preliminary the effects of the photocatalyst loading, the initial pH and the initial rosuvastatin concentration were evaluated. The experimental results showed that rosuvastatin degradation is primarily a photocatalytic process, with pseudo-first order kinetics. The byproducts that were generated during the oxidative process were identified using nano-ultra performance liquid chromatography tandem mass spectrometry (nano-UPLC–MS/MS) and acute toxicity tests using Daphnia magna were done to evaluate the toxicity of the untreated rosuvastatin solution and the reactor effluent. - Highlights: • The photocatalytic degradation of rosuvastatin was studied under UV irradiation. • Commercial catalyst ZnO was used. • Initial rosuvastatin concentration, photocatalyst loading and pH were evaluated. • The byproducts generated during the oxidative process were detected and identified. • Acute toxicity tests using Daphnia magna were carried out.

  8. Comparative study of the vapor analytes of trinitrotoluene (TNT)

    Science.gov (United States)

    Edge, Cindy C.; Gibb, Julie; Dugan, Regina E.

    1998-12-01

    Trinitrotoluene (TNT) is a high explosive used in most antipersonnel and antitank landmines. The Institute for Biological Detection Systems (IBDS) has developed a quantitative vapor delivery system, termed olfactometer, for conducting canine olfactory research. The research is conducted utilizing dynamic conditions, therefore, it is imperative to evaluate the headspace of TNT to ensure consistency with the dynamic generation of vapor. This study quantified the vapor headspace of military- grade TNT utilizing two different vapor generated methodologies, static and dynamic, reflecting differences between field and laboratory environments. Static vapor collection, which closely mimics conditions found during field detection, is defined as vapor collected in an open-air environment at ambient temperature. Dynamic vapor collection incorporates trapping of gases from a high flow vapor generation cell used during olfactometer operation. Analysis of samples collected by the two methodologies was performed by gas chromatography/mass spectrometry and the results provided information with regard to the constituents detected. However, constituent concentration did vary between the sampling methods. This study provides essential information regarding the vapor constituents associated with the TNT sampled using different sampling methods. These differences may be important in determining the detection signature dogs use to recognize TNT.

  9. Experimental and analytical study of natural circulation in square loop

    International Nuclear Information System (INIS)

    Moorthi, A.; Prem Sai, K.; Ravi, K.V.

    2015-01-01

    The nuclear safety under station blackout conditions is a major concern in the design of the nuclear reactors. In the case of existing reactors, the heat removal capability of cooling systems under natural circulation conditions is to be ascertained by experiments/analysis. This will ensure the long term core cooling and thereby, the safety of reactor core. Natural circulation occurs when the heat sink is at a higher elevation compared with the heat source. In case, the heat source and the sink are nearly at the same elevation, the difference in the elevations of their thermal centres can provide the elevation head required for natural circulation. An experimental study of natural circulation in the above geometry was carried out. The effect of flow resistance, Heat Source strength (heater power) and elevation difference between the source and the sink on the heat transfer were studied. The results of the experiments were analysed using RELAP5/MOD 3.2 and a good match between the experimental data and RELAP5 predictions is observed. (author)

  10. Analytical and Experimental Feasibility Study of Combined OTEC on NPPs

    Energy Technology Data Exchange (ETDEWEB)

    Cho, Jeongtae; Oh, Kyemin; Heo, Gyunyoung [Kyung Hee Univ., Yongin (Korea, Republic of); Jung, Hoon [KEPCO Research Institute, Daejeon (Korea, Republic of)

    2013-05-15

    The concept of the Combined Ocean Thermal Energy Conversion (Combined OTEC) needs to study. Combined OTEC uses exhausted steam on Nuclear Power Plants (NPPs) as heat source instead surface water. Exhausted steam extracted from condenser evaporates working fluid of Combined OTEC at heat exchanger (Hx-W). Essential calculation for conceptual design of Combined OTEC was already performed and presented before. However, the technical issue whether sufficient extraction of exhausted steam from high degree of vacuum of condenser to Hx-W can be supplied or not was unclear, which is significant to continue a demonstration program. In this study, so, we calculated the rate of extracted steam to evaluate whether sufficient steam can be extracted using RELAP code. In aspect of implementation of Combined OTEC, confirmation of sufficient flow of exhausted steam into Hx-W is the starting point of research. As the result of RELAP calculation, we confirmed that exhausted steam would flow into Hx-W. Considering the amount of exhausted steam in NPPs which is 1000 MWe and has 36 % of efficiency, 9 % of flow rate to Hx-W is means that 160 MWt of heat can be available as heat source of Combined OTEC. Using this, it can be possible to improve efficiency of aged NPPs and can compensate power loss caused by increase of circulation water temperature particularly in summer season.

  11. Analytical studies of plasma extraction electrodes and ion beam formation

    International Nuclear Information System (INIS)

    Hassan, A.; Elsaftawy, A.; Zakhary, S. G.

    2007-01-01

    In this work a theoretical and computational study on the space charge dominated beams extracted from a plasma ion source through a spherical and planer electrode is simulated and optimized. The influence of some electrode parameters: axial position, electrode diameter, material and shape; on ion current extracted from a plasma source; were investigated and compared. The optimum values and conditions of the curvature of the plasma boundary, angular divergence, perveance, and the extraction gap were optimized to extract a high quality beams. It has shown that for a planar electrode system there is usually a minimum for optimum perveance versus angular divergence at about ? 0.6 for corresponding aspect ratios. This was assured by experimental data. The appropriate spherical electrode system focus the beam to a minimum value located at a distance equal to the focal length of the spherical extraction electrode.

  12. Multi-analytical study of historical semiconductor pigments

    International Nuclear Information System (INIS)

    Caporosso, V.

    2015-01-01

    This work is focused on the study of semiconductor-based pigments, which substituted traditional pigments in the second half of the 19. century. Synthetic semiconductor pigments may be chemically unstable due to the presence of many impurities unintentionally introduced during manufacturing. The aim of this work is to provide an insight on the application of X-ray Fluorescence (XRF) for the analysis of these painting materials, including both Cd- and Zn-based pigments. Three different approaches have been followed: the semi-quantitative analysis of samples with similar elemental composition, the complementary use of XRF and Raman spectroscopy for the analysis of elemental and molecular composition and the synchrotron-based XRF and XANES for the detection of impurities. The synergetic combination of different techniques provides information useful for the definition of specific markers for future analysis of paint-samples with implications for the conservation and treatment of late 19. and early 20. century paintings.

  13. Analytical study on spherules from Toungouska explosion site

    International Nuclear Information System (INIS)

    Jehanno, C.; Robin, E.; Rocchia, R.; Boclet, D.; Danon, J.

    1989-01-01

    Eighty years after the event, the Tunguska explosion of june 1908, has not found a satisfactory explanation. The cosmic bolide, supposed responsible for the event, has not yet been identified but numerous magnetic spherules have been recovered in the vicinity of the explosion site. Eighty spherules have been studied and compared with the Fe-Ni spherules from the steady micrometeoroid flux. Ninety percents of them cannot be identified with any known micrometeoroid families; their low average iridium content rather suggests a terrestrial origin. Five other spherules are obviously Fe-Ni spherules of the steady micrometeoroid rain and, thus, are unrelated the Tunguska event. Only three of the 80 spherules, consisting of a single iron oxide phase, could have been produced by the event. (author)

  14. Tribes and chiefdoms: An analytical study of some Brazilian ceramics

    International Nuclear Information System (INIS)

    Sabino, C.V.S.; Prous, A.P.; Wuest, I.; Guapindaia, V.

    2003-01-01

    There is no evidence of urban civilization in Brazilian prehistory; most inhabitants lived in tribal organizations, probably with regional economic integration among several independent tribes. There is little evidence of seasonal migrations between the coastal and inland areas of southern Brazil. Some specialized horticulturists competed among themselves but other groups lived more in isolation, and probably peacefully, in the upper interfluvial regions.The chiefdom system is supposed to have existed only along the river Amazon. In this region, some pottery makers may have been specialized craftsmen, and the finest ceramics that could have been exported from one village or region to another can be found. Outside this region, pottery was generally plain, except the tupiguarani, which was partly decorated. In this study some limited possibilities were tested, in three different cultural and regional contexts, to find out if the application of chemical analysis to economically and politically 'simple' societies can produce any results of additional archaeological relevance. (author)

  15. Analytical study of sodium combustion phenomena under sodium leak accidents

    International Nuclear Information System (INIS)

    Kim, Byung Ho; Jeong, J. Y.; Jeong, K. C.; Kim, T. J.; Choi, J. H.

    2001-12-01

    The rise of temperature and pressure, the release of aerosol in the buildings as a result of sodium fire must be considered for the safety measures of LMR. Therefore for the safety of the LMR, it is necessary to understand the characteristics of sodium fire, resulting from the various type of leakage. ASSCOPS(Analysis of Simultaneous Sodium Combustion in Pool and Spray) is the computer code for the analysis of the thermal consequence of sodium leak and fire in LMR that has been developed by Japan Nuclear Cycle Development Institute(JNC) in Japan. In this study, a preliminary analysis of sodium leak and fire accidents in S/G building of KALIMER is made by using ASSCOPS code. Various phenomena of interest are spray and pool burning, peak pressure, temperature change, local structure temperature, aerosol behavior, drain system into smothering tank, ventilation characteristics at each cell with the safety venting system and nitrogen injection system. In this calculation, the dimension of the S/G building was chosen in accordance with the selected options of LMR name KALIMER(Korea). As a result of this study, it was shown that subsequent effect of sodium fire depended upon whether the sodium continued to leak from the pipe or not, whether the ventilation system was running, whether the inert gas injection system was provided, whether the sodium on floor was drained into the smothering tank or not, whether the building was sealed or not, etc. Specially the excessive rise of pressure into each cell was prevented by installing the pressure release plates on wall of the building

  16. An Analytical Study of Tools and Techniques for Movie Marketing

    Directory of Open Access Journals (Sweden)

    Garima Maik

    2014-08-01

    Full Text Available Abstract. Bollywood or Hindi movie industry is one of the fastest growing sector in the media and entertainment space creating numerous business and employment opportunities. Movies in India are a major source of entertainment for all sects of society. They not only face competition from other movie industries and movies but from other source of entertainment such as adventure sports, amusement parks, theatre and drama, pubs and discothèques. A lot of man power, man hours, creative brains, and money are put in to build a quality feature film. Bollywood is the industry which continuously works towards providing the 7 billion population with something new always. So it is important for the movie and production team to stand out, to grab the due attention of the maximum audience. Movie makers employ various tools and techniques today to market their movies. They leave no stone unturned. They roll out teasers, First look, Theatrical trailer release, Music launch, City tours, Producer’s and director’s interview, Movie premier, Movie release, post release follow up and etc. to pull the viewers to the Cineplex. The audience today which comprises mainly of youth requires photos, videos, meet ups, gossip, debate, collaboration and content creation. These requirements of today’s generation are most fulfilled through digital platforms. However, the traditional media like newspapers, radio, and television are not old school. They reach out to mass audience and play an upper role in effective marketing. This study aims at analysing these tools for their effectiveness. The objectives are fulfilled through a consumer survey. This study will bring out the effectiveness and relational importance of various tools which are employed by movie marketers to generate maximum returns on the investments by using various data reduction techniques like factor analysis and statistical techniques like chi-square test with data visualization using pie charts

  17. THE FARTHEST MOSQUE OR THE ALLEGED TEMPLE AN ANALYTIC STUDY

    Directory of Open Access Journals (Sweden)

    Yehia Hassan Wazeri

    2013-12-01

    Full Text Available Abstract The Farthest Mosque (Al-Masjid Al-Aqsa in Jerusalem has been associated in the consciousness of the Muslims, with The Sacred Mosque (Al-Masjid Al-Haram in Makkah through a spiritual bond since the event of Isra’ (Night Journey and Mi`raj (Ascension to Heaven. The objective of this study is to determine the orientation of the Farthest Mosque and illustrate the similarity in geometric shape (plan and proportions, between the Farthest Mosque in Jerusalem and the sacred mosque (Al-Ka`bah in Makkah, in the first part of the research. The second part of the research involves a study of some texts from the Old Testament that address the architectural and structural descriptions of the alleged temple, with the purpose of exposing whether glaring contradictions exist between the texts of the Old Testament themselves or between them and the real architectural and structural facts acknowledged by specialists in this field. Keywords: The Farthest mosque, the Alleged Temple, Al-Ka`bah, geometric similarity     Abstrak Masjid tertua (Masjid al-Aqsa di Jarusalem telah dihubungkan dalam kesadaran umat muslim, dengan masjid suci (Masjidil Haram di Mekah melalui ikatan spiritual sejak kejadian Isra’ (perjalanan malam dan Mi’raj (kenaikan  ke  surga.  Tujuan  dari  kajian  ini  adalah  untuk  menentukan  orientasi  masjid  tertua  and menggambarkan kesamaan bentuk geometri (denah dan proporsi, antara masjid tertua di Jarusalem dan masjid suci (Ka’bah di Mekah, di bagian pertama penelitian. Bagian kedua penelitian melibatkan kajian beberapa tulisan dari surat wasiat kuno yang mengarah kepada deskripsi arsitektural dan struktural kuil, dengan tujuan mengekspos baik kontradiksi yang mencolok antara tulisan surat wasiat kuno itu sendiri maupun di antara mereka, dan fakta arsitektural dan struktural yang nyata diakui oleh spesialis di lapangan   Kata kunci: masjid tertua, kuil, ka’bah, kesamaan geometri

  18. Analytical techniques applied to study cultural heritage objects

    International Nuclear Information System (INIS)

    Rizzutto, M.A.; Curado, J.F.; Bernardes, S.; Campos, P.H.O.V.; Kajiya, E.A.M.; Silva, T.F.; Rodrigues, C.L.; Moro, M.; Tabacniks, M.; Added, N.

    2015-01-01

    The scientific study of artistic and cultural heritage objects have been routinely performed in Europe and the United States for decades. In Brazil this research area is growing, mainly through the use of physical and chemical characterization methods. Since 2003 the Group of Applied Physics with Particle Accelerators of the Physics Institute of the University of Sao Paulo (GFAA-IF) has been working with various methodologies for material characterization and analysis of cultural objects. Initially using ion beam analysis performed with Particle Induced X-Ray Emission (PIXE), Rutherford Backscattering (RBS) and recently Ion Beam Induced Luminescence (IBIL), for the determination of the elements and chemical compounds in the surface layers. These techniques are widely used in the Laboratory of Materials Analysis with Ion Beams (LAMFI-USP). Recently, the GFAA expanded the studies to other possibilities of analysis enabled by imaging techniques that coupled with elemental and compositional characterization provide a better understanding on the materials and techniques used in the creative process in the manufacture of objects. The imaging analysis, mainly used to examine and document artistic and cultural heritage objects, are performed through images with visible light, infrared reflectography (IR), fluorescence with ultraviolet radiation (UV), tangential light and digital radiography. Expanding more the possibilities of analysis, new capabilities were added using portable equipment such as Energy Dispersive X-Ray Fluorescence (ED-XRF) and Raman Spectroscopy that can be used for analysis 'in situ' at the museums. The results of these analyzes are providing valuable information on the manufacturing process and have provided new information on objects of different University of Sao Paulo museums. Improving the arsenal of cultural heritage analysis it was recently constructed an 3D robotic stage for the precise positioning of samples in the external beam setup

  19. Analytical techniques applied to study cultural heritage objects

    Energy Technology Data Exchange (ETDEWEB)

    Rizzutto, M.A.; Curado, J.F.; Bernardes, S.; Campos, P.H.O.V.; Kajiya, E.A.M.; Silva, T.F.; Rodrigues, C.L.; Moro, M.; Tabacniks, M.; Added, N., E-mail: rizzutto@if.usp.br [Universidade de Sao Paulo (USP), SP (Brazil). Instituto de Fisica

    2015-07-01

    The scientific study of artistic and cultural heritage objects have been routinely performed in Europe and the United States for decades. In Brazil this research area is growing, mainly through the use of physical and chemical characterization methods. Since 2003 the Group of Applied Physics with Particle Accelerators of the Physics Institute of the University of Sao Paulo (GFAA-IF) has been working with various methodologies for material characterization and analysis of cultural objects. Initially using ion beam analysis performed with Particle Induced X-Ray Emission (PIXE), Rutherford Backscattering (RBS) and recently Ion Beam Induced Luminescence (IBIL), for the determination of the elements and chemical compounds in the surface layers. These techniques are widely used in the Laboratory of Materials Analysis with Ion Beams (LAMFI-USP). Recently, the GFAA expanded the studies to other possibilities of analysis enabled by imaging techniques that coupled with elemental and compositional characterization provide a better understanding on the materials and techniques used in the creative process in the manufacture of objects. The imaging analysis, mainly used to examine and document artistic and cultural heritage objects, are performed through images with visible light, infrared reflectography (IR), fluorescence with ultraviolet radiation (UV), tangential light and digital radiography. Expanding more the possibilities of analysis, new capabilities were added using portable equipment such as Energy Dispersive X-Ray Fluorescence (ED-XRF) and Raman Spectroscopy that can be used for analysis 'in situ' at the museums. The results of these analyzes are providing valuable information on the manufacturing process and have provided new information on objects of different University of Sao Paulo museums. Improving the arsenal of cultural heritage analysis it was recently constructed an 3D robotic stage for the precise positioning of samples in the external beam setup

  20. Impaired Water 303(d) Polygons, Arizona, 2004, Arizona Department of Environmental Quality

    Data.gov (United States)

    U.S. Environmental Protection Agency — Arizona 303(d) waterbodies for 2004. These include lakes, reservoirs, ponds, etc. The 303(d) list is a related table to the feature class AZ_303d_04_area. Arizona's...

  1. [Obstructive sleep apnea syndrome. Analytical study of 63 cases].

    Science.gov (United States)

    Battikh, Mohamed H; Joobeur, Sameh; Ben Sayeh, Mohamed M; Rouetbi, Naceur; Maatallah, Anis; Daami, Monia; el Kamel, Ali

    2004-02-01

    Obstructive sleep apnoea (OSA) is a relatively common disorder, in developed country with prevalence estimated to lie between 2 and 4% in adult population. The diagnosis of this syndrome is made on the basis of characteristic clinical features and the results of nocturnal polysomnography. There is no data concerning the OSA in developing country. It is therefore of interest to determine the clinic and polysomnographic profile of this disease and to landmark factors correlated with severity in our country. This was achieved by studying a set of 63 OSA. The mean of age was 53 + 13 years with sex ratio 1. The means of Epworth sleepiness scale score, BMI and Apnoea/Hypopnoea index (AHI) were respectively 16 + 4, 38.8 + 7 kg/m2 and 51.7 + 28.6. 44% of patients have OSA severe with IAH > 50/h. Arousal index and desaturation index were respectively 36.4 + 21.7 and 49 + 26. Trial of continuous positive airway pressure (CPAP) therapy was proposed first to 40 patients, 17 were able to use CPAP.

  2. Water hammer and its effect on ageing: an analytical study

    International Nuclear Information System (INIS)

    Kedia, Suruchi

    2006-01-01

    Water hammer can be disastrous from the point of view of ageing of the pipe(s)/Piping system. Design of restraints and protection devices for the various piping systems must consider severe stresses that may generate because of fluid transients. These fluid transients are termed as water hammer when it is restricted to water. But to have limited margins on the stress loads of piping system it is very important to predict the actual dimensions of the stresses. This paper covers various causes and analyses of the situations under which water hammer waves get generated and also way(s) to have control on occurrences of such situations. Few case studies are also covered showing the results and graphs of the stress waves generated because of water hammer. Effort has also been made in the paper in the direction to find out the methodology to compute the ageing of the system because of water hammer waves. Further in this paper an attempt is made to show the systematic methodology towards the diagnosis of water hammer that can be treated as a foundation stone for the creation of water hammer diagnosis system. Active measures to minimize the water hammer intensity by influencing fluid dynamic conditions of the system will also be suggested. Finally the paper will present the ageing aspects because of the stresses that generate due to water hammer. (author)

  3. An Analytical Study of Mammalian Bite Wounds Requiring Inpatient Management

    Directory of Open Access Journals (Sweden)

    Young-Geun Lee

    2013-11-01

    Full Text Available BackgroundMammalian bite injuries create a public health problem because of their frequency, potential severity, and increasing number. Some researchers have performed fragmentary analyses of bite wounds caused by certain mammalian species. However, little practical information is available concerning serious mammalian bite wounds that require hospitalization and intensive wound management. Therefore, the purpose of this study was to perform a general review of serious mammalian bite wounds.MethodsWe performed a retrospective review of the medical charts of 68 patients who were referred to our plastic surgery department for the treatment of bite wounds between January 2003 and October 2012. The cases were analyzed according to the species, patient demographics, environmental factors, injury characteristics, and clinical course.ResultsAmong the 68 cases of mammalian bite injury, 58 (85% were caused by dogs, 8 by humans, and 2 by cats. Most of those bitten by a human and both of those bitten by cats were male. Only one-third of all the patients were children or adolescents. The most frequent site of injury was the face, with 40 cases, followed by the hand, with 16 cases. Of the 68 patients, 7 were treated with secondary intention healing. Sixty-one patients underwent delayed procedures, including delayed direct closure, skin graft, composite graft, and local flap.ConclusionsBased on overall findings from our review of the 68 cases of mammalian bites, we suggest practical guidelines for the management of mammalian bite injuries, which could be useful in the treatment of serious mammalian bite wounds.

  4. mosaicQA - A General Approach to Facilitate Basic Data Quality Assurance for Epidemiological Research.

    Science.gov (United States)

    Bialke, Martin; Rau, Henriette; Schwaneberg, Thea; Walk, Rene; Bahls, Thomas; Hoffmann, Wolfgang

    2017-05-29

    Epidemiological studies are based on a considerable amount of personal, medical and socio-economic data. To answer research questions with reliable results, epidemiological research projects face the challenge of providing high quality data. Consequently, gathered data has to be reviewed continuously during the data collection period. This article describes the development of the mosaicQA-library for non-statistical experts consisting of a set of reusable R functions to provide support for a basic data quality assurance for a wide range of application scenarios in epidemiological research. To generate valid quality reports for various scenarios and data sets, a general and flexible development approach was needed. As a first step, a set of quality-related questions, targeting quality aspects on a more general level, was identified. The next step included the design of specific R-scripts to produce proper reports for metric and categorical data. For more flexibility, the third development step focussed on the generalization of the developed R-scripts, e.g. extracting characteristics and parameters. As a last step the generic characteristics of the developed R functionalities and generated reports have been evaluated using different metric and categorical datasets. The developed mosaicQA-library generates basic data quality reports for multivariate input data. If needed, more detailed results for single-variable data, including definition of units, variables, descriptions, code lists and categories of qualified missings, can easily be produced. The mosaicQA-library enables researchers to generate reports for various kinds of metric and categorical data without the need for computational or scripting knowledge. At the moment, the library focusses on the data structure quality and supports the assessment of several quality indicators, including frequency, distribution and plausibility of research variables as well as the occurrence of missing and extreme values. To

  5. Case Study: IBM Watson Analytics Cloud Platform as Analytics-as-a-Service System for Heart Failure Early Detection

    Directory of Open Access Journals (Sweden)

    Gabriele Guidi

    2016-07-01

    Full Text Available In the recent years the progress in technology and the increasing availability of fast connections have produced a migration of functionalities in Information Technologies services, from static servers to distributed technologies. This article describes the main tools available on the market to perform Analytics as a Service (AaaS using a cloud platform. It is also described a use case of IBM Watson Analytics, a cloud system for data analytics, applied to the following research scope: detecting the presence or absence of Heart Failure disease using nothing more than the electrocardiographic signal, in particular through the analysis of Heart Rate Variability. The obtained results are comparable with those coming from the literature, in terms of accuracy and predictive power. Advantages and drawbacks of cloud versus static approaches are discussed in the last sections.

  6. Nationwide Multicenter Reference Interval Study for 28 Common Biochemical Analytes in China.

    Science.gov (United States)

    Xia, Liangyu; Chen, Ming; Liu, Min; Tao, Zhihua; Li, Shijun; Wang, Liang; Cheng, Xinqi; Qin, Xuzhen; Han, Jianhua; Li, Pengchang; Hou, Li'an; Yu, Songlin; Ichihara, Kiyoshi; Qiu, Ling

    2016-03-01

    A nationwide multicenter study was conducted in the China to explore sources of variation of reference values and establish reference intervals for 28 common biochemical analytes, as a part of the International Federation of Clinical Chemistry and Laboratory Medicine, Committee on Reference Intervals and Decision Limits (IFCC/C-RIDL) global study on reference values. A total of 3148 apparently healthy volunteers were recruited in 6 cities covering a wide area in China. Blood samples were tested in 2 central laboratories using Beckman Coulter AU5800 chemistry analyzers. Certified reference materials and value-assigned serum panel were used for standardization of test results. Multiple regression analysis was performed to explore sources of variation. Need for partition of reference intervals was evaluated based on 3-level nested ANOVA. After secondary exclusion using the latent abnormal values exclusion method, reference intervals were derived by a parametric method using the modified Box-Cox formula. Test results of 20 analytes were made traceable to reference measurement procedures. By the ANOVA, significant sex-related and age-related differences were observed in 12 and 12 analytes, respectively. A small regional difference was observed in the results for albumin, glucose, and sodium. Multiple regression analysis revealed BMI-related changes in results of 9 analytes for man and 6 for woman. Reference intervals of 28 analytes were computed with 17 analytes partitioned by sex and/or age. In conclusion, reference intervals of 28 common chemistry analytes applicable to Chinese Han population were established by use of the latest methodology. Reference intervals of 20 analytes traceable to reference measurement procedures can be used as common reference intervals, whereas others can be used as the assay system-specific reference intervals in China.

  7. ANALYTICAL STUDY OF ESSENTIAL INFANTILE ESOTROPIA AND ITS MANAGEMENT

    Directory of Open Access Journals (Sweden)

    Kandasamy Sivakumar

    2017-06-01

    Full Text Available BACKGROUND Essential Infantile Esotropia (EIE is the most common type of strabismus. About 0.1% of the newborn are found to have esotropia. 1 Though present since birth, it becomes manifest and remains constant around six months of age. The features are large angle constant strabismus, defective Binocular Single Vision (BSV, cross fixation, DVD and latent nystagmus. Most of the patients have mild-to-moderate hyperopia; the amount of deviation is unrelated to the amount and type of refractive error. MATERIALS AND METHODS Fifty cases with EIE were included in this prospective study. A thorough ophthalmic and orthoptic evaluation was done in all the patients. For patients more than three years of age, the angle of deviation was measured with prism bar cover test, and for patients less than three years of age, angle of deviation was measured with Hirschberg’s test. Associated features like cross fixation, abduction limitation, Dissociated Vertical Deviation (DVD, nystagmus, amblyopia and Inferior Oblique Overaction (IOOA were documented. Occlusion therapy was given to amblyopic patients prior to surgery. All these patients underwent surgery and were followed up for a period of six months. RESULTS The prevalence of EIE in our centre was 0.33%. Of the fifty patients, 28 were males and 22 were female patients. 39 patients (78% had deviation of 30-50 Prism Dioptres (PD. Incidence of DVD, inferior oblique overaction and nystagmus was found to be lower when compared to western population. Amblyopia should be diagnosed early and treated adequately before surgery. Standard surgical option is bimedial recession. Monocular recession-resection surgery in one eye can be opted for in cases of irreversible amblyopia. Three or four muscle surgery can be done if deviation is very large. If marked inferior oblique overaction is present, the same should be weakened in addition to the horizontal muscle surgery. CONCLUSION EIE is the most common type of strabismus

  8. A Horneyan analytic perspective on couple therapy: a case study.

    Science.gov (United States)

    Horwitz, N M

    1994-09-01

    This paper describes the study, diagnosis, and course of treatment of a marital couple incorporating Horney theory as a basis for understanding. The case illustrates how fundamental features of Horney theory--character structure, pride positions, attacks on the idealized image, alienated aspects of self, externalization and counter-externalization-can be illuminated in the expanded context of a specific other, the spouse, as background. In a marriage characterized by conflict, omnipresent struggles for authority, and malignantly destructive communication, the wife adopts a position of self-effacement externalizing expansiveness to her husband while the husband adopts an expansive-detached position externalizing both expansiveness and self-effacement to the wife. Externalizations from the wife include a form that has not been described in the psychoanalytic literature of the Horney school: indirect active externalization. As shown, the wife attributes an idealization of her husband to third parties. We observe, too, that the husband's reasonableness and the wife's emotional stridency have the effect of attacking the idealized image of the other. Defenses are mobilized in order to repair hurt pride reactions: for the husband, the wife's stridency is an assault on his sense of himself as a principled, virtous man. For the wife, the husband's reasonableness is experienced as an assault on her sense of herself as a caring wife and mother. In order to block their pride responses and attacks on each other's idealized image, which made conjoint sessions antagonistic and unproductive for a time, a "glass wall" technique was employed for some months that enabled each to speak to the other through me. I struggled against the temptation of siding with the husband's rationality and seeing the wife as secondary. I came to understand that the husband's reasonableness was oppressive for the wife. In order for the wife to feel understood empathically, I needed to fill the role of

  9. Analytical studies on optimization of containment design pressure

    International Nuclear Information System (INIS)

    Haware, S.K.; Ghosh, A.K.; Kushwaha, H.S.

    2005-01-01

    optimizing on the size of BOP in order to optimize the containment design pressure. The results of the optimization studies are presented and discussed in the paper. (authors)

  10. Proposal for a Similar Question Search System on a Q&A Site

    Directory of Open Access Journals (Sweden)

    Katsutoshi Kanamori

    2014-06-01

    Full Text Available There is a service to help Internet users obtain answers to specific questions when they visit a Q&A site. A Q&A site is very useful for the Internet user, but posted questions are often not answered immediately. This delay in answering occurs because in most cases another site user is answering the question manually. In this study, we propose a system that can present a question that is similar to a question posted by a user. An advantage of this system is that a user can refer to an answer to a similar question. This research measures the similarity of a candidate question based on word and dependency parsing. In an experiment, we examined the effectiveness of the proposed system for questions actually posted on the Q&A site. The result indicates that the system can show the questioner the answer to a similar question. However, the system still has a number of aspects that should be improved.

  11. Born analytical or adopted over time? a study investigating if new analytical tools can ensure the survival of market oriented startups.

    OpenAIRE

    Skogen, Hege Janson; De la Cruz, Kai

    2017-01-01

    Masteroppgave(MSc) in Master of Science in Strategic Marketing Management - Handelshøyskolen BI, 2017 This study investigates whether the prevalence of technological advances within quantitative analytics moderates the effect market orientation has on firm performance, and if startups can take advantage of the potential opportunities to ensure their own survival. For this purpose, the authors review previous literature in marketing orientation, startups, marketing analytics, an...

  12. 76 FR 28210 - Eastern Arizona Counties Resource Advisory Committee

    Science.gov (United States)

    2011-05-16

    ... DEPARTMENT OF AGRICULTURE Forest Service Eastern Arizona Counties Resource Advisory Committee AGENCY: Forest Service, USDA. ACTION: Notice of meeting. SUMMARY: The Eastern Arizona Counties will meet...: Julia Faith Rivera, RAC Program Manager, Eastern Arizona Counties Resource Advisory Committee, Apache...

  13. 76 FR 41755 - Eastern Arizona Counties Resource Advisory; Meeting

    Science.gov (United States)

    2011-07-15

    ... DEPARTMENT OF AGRICULTURE Forest Service Eastern Arizona Counties Resource Advisory; Meeting AGENCY: Forest Service, USDA. ACTION: Notice of meeting. SUMMARY: The Eastern Arizona Counties Resource... FURTHER INFORMATION CONTACT: Julia Faith Rivera, RAC Program Manager, Eastern Arizona Counties Resource...

  14. The GSPC: Newest Franchise in al-Qa'ida's Global Jihad

    National Research Council Canada - National Science Library

    Boudali, Lianne K

    2007-01-01

    ... of support in Europe. The alignment of the GSPC with al Qa ida represents a significant change in the group's strategy, however, its decision to join al Qa ida's global jihad should be understood as an act of desperation...

  15. Restrictive Language Policy in Practice: English Learners in Arizona

    Science.gov (United States)

    Heineke, Amy J.

    2016-01-01

    As the most restrictive language policy context in the United States, Arizona's monolingual and prescriptive approach to teaching English learners continues to capture international attention. More than five school years after initial implementation, this study uses qualitative data from the individuals doing the policy work to provide a holistic…

  16. Language Ideologies of Arizona Voters, Language Managers, and Teachers

    Science.gov (United States)

    Fitzsimmons-Doolan, Shannon

    2014-01-01

    Arizona is the site of many explicit language policies as well as ongoing scholarly discussions of related language ideologies--beliefs about the role of language in society. This study adds a critical piece to the investigation of the role of ideologies in language policy processes by thoroughly documenting language ideologies expressed by a…

  17. Statistical process control analysis for patient-specific IMRT and VMAT QA.

    Science.gov (United States)

    Sanghangthum, Taweap; Suriyapee, Sivalee; Srisatit, Somyot; Pawlicki, Todd

    2013-05-01

    This work applied statistical process control to establish the control limits of the % gamma pass of patient-specific intensity modulated radiotherapy (IMRT) and volumetric modulated arc therapy (VMAT) quality assurance (QA), and to evaluate the efficiency of the QA process by using the process capability index (Cpml). A total of 278 IMRT QA plans in nasopharyngeal carcinoma were measured with MapCHECK, while 159 VMAT QA plans were undertaken with ArcCHECK. Six megavolts with nine fields were used for the IMRT plan and 2.5 arcs were used to generate the VMAT plans. The gamma (3%/3 mm) criteria were used to evaluate the QA plans. The % gamma passes were plotted on a control chart. The first 50 data points were employed to calculate the control limits. The Cpml was calculated to evaluate the capability of the IMRT/VMAT QA process. The results showed higher systematic errors in IMRT QA than VMAT QA due to the more complicated setup used in IMRT QA. The variation of random errors was also larger in IMRT QA than VMAT QA because the VMAT plan has more continuity of dose distribution. The average % gamma pass was 93.7% ± 3.7% for IMRT and 96.7% ± 2.2% for VMAT. The Cpml value of IMRT QA was 1.60 and VMAT QA was 1.99, which implied that the VMAT QA process was more accurate than the IMRT QA process. Our lower control limit for % gamma pass of IMRT is 85.0%, while the limit for VMAT is 90%. Both the IMRT and VMAT QA processes are good quality because Cpml values are higher than 1.0.

  18. Semivolatile organic compounds in residential air along the Arizona - Mexico border

    Science.gov (United States)

    Gale, R.W.; Cranor, W.L.; Alvarez, D.A.; Huckins, J.N.; Petty, J.D.; Robertson, G.L.

    2009-01-01

    Concerns about indoor air quality and the potential effects on people living in these environments are increasing as more reports about the toxicities and the potential indoor air exposure levels of household-use chemicals and chemicals fromhousingandfurnishingmanufactureinairarebeingassessed. Gas chromatography/mass spectrometry was used to confirm numerous airborne contaminants obtained from the analysis of semipermeable membrane devices deployed inside of 52 homes situated along the border between Arizona and Mexico. We also describe nontarget analytes in the organochlorine pesticide fractions of 12 of these homes; this fraction is also the most likelytocontainthebroadestscopeofbioconcentratablechemicals accumulated from the indoor air. Approximately 400 individual components were identified, ranging from pesticides to a wide array of hydrocarbons, fragrances such as the musk xylenes, flavors relating to spices, aldehydes, alcohols, esters and phthalate esters, and other miscellaneous types of chemicals. The results presented in this study demonstrate unequivocally that the mixture of airborne chemicals present indoors is far more complex than previously demonstrated. ?? 2009 American Chemical Society.

  19. 77 FR 51966 - Eastern Arizona Resource Advisory Committee

    Science.gov (United States)

    2012-08-28

    ... DEPARTMENT OF AGRICULTURE Forest Service Eastern Arizona Resource Advisory Committee AGENCY: Forest Service, USDA. ACTION: Notice of meeting. SUMMARY: The Eastern Arizona Resource Advisory Committee...

  20. Utility view on QA/QC of WWER-440 fuel design and manufacture

    International Nuclear Information System (INIS)

    Vesely, P.

    1999-01-01

    In this lecture the legislation implements in the Czech Republic, QA/QC system at CEZ, demonstration and development program (purchaser point of view), audit of QA/QC system for fuel design and manufacturing as well as QA/QC records are discussed

  1. THE IMPORTANCE OF A SUCCESSFUL QUALITY ASSURANCE (QA) PROGRAM FROM A RESEARCH MANAGER'S PERSPECTIVE

    Science.gov (United States)

    The paper discusses the Air Pollution Prevention and Control Division's Quality Assurance (QA) program and the approaches used to meet QA requirements in the Division. The presentation is a technical manager's perspective of the Division's requirements for and approach to QA in i...

  2. Quality assurance (QA) training at Westinghouse including innovative approaches for achieving an effective QA programme and establishing constructive interaction

    International Nuclear Information System (INIS)

    Chivers, J.H.; Scanga, B.E.

    1982-01-01

    Experience of the Westinghouse Water Reactors Division with indoctrination and training of quality engineers includes training of personnel from Westinghouse divisions in the USA and overseas as well as of customers' personnel. A written plan is prepared for each trainee in order to fit the training to the individual's needs, and to cover the full range of information and activities. The trainee is also given work assignments, working closely with experienced quality engineers. He may prepare inspection plans and audit check lists, assist in the preparation of QA training modules, write procedures, and perform supplier surveillance and data analyses, or make special studies of operating systems. The trainee attends seminars and special courses on work-related technical subjects. Throughout the training period, emphasis is placed on inculcating an attitude of team work in the trainee so that the result of the training is the achievement of both quality and productivity. Certification is extended (given that education/experience/skill requirements are met) to such functions as mechanical equipment quality engineering, electrical equipment quality engineering, and start-up and testing quality engineering. A well-trained quality engineer is equipped to provide technical assistance to other disciplines and, through effective co-operation with others, contributes to the success of the organization's endeavours. (author)

  3. Low energy ion beam systems for surface analytical and structural studies

    International Nuclear Information System (INIS)

    Nelson, G.C.

    1980-01-01

    This paper reviews the use of low energy ion beam systems for surface analytical and structural studies. Areas where analytical methods which utilize ion beams can provide a unique insight into materials problems are discussed. The design criteria of ion beam systems for performing materials studies are described and the systems now being used by a number of laboratories are reviewed. Finally, several specific problems are described where the solution was provided at least in part by information provided by low energy ion analysis techniques

  4. Analytical Study of High Concentration PCB Paint at the Heavy Water Components Test Reactor

    International Nuclear Information System (INIS)

    Lowry, N.J.

    1998-01-01

    This report provides results of an analytical study of high concentration PCB paint in a shutdown nuclear test reactor located at the US Department of Energy's Savannah River Site (SRS). The study was designed to obtain data relevant for an evaluation of potential hazards associated with the use of and exposure to such paints

  5. Analytical Study of High Concentration PCB Paint at the Heavy Water Components Test Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Lowry, N.J.

    1998-10-21

    This report provides results of an analytical study of high concentration PCB paint in a shutdown nuclear test reactor located at the US Department of Energy's Savannah River Site (SRS). The study was designed to obtain data relevant for an evaluation of potential hazards associated with the use of and exposure to such paints.

  6. The Effect of Brain Based Learning on Academic Achievement: A Meta-Analytical Study

    Science.gov (United States)

    Gozuyesil, Eda; Dikici, Ayhan

    2014-01-01

    This study's aim is to measure the effect sizes of the quantitative studies that examined the effectiveness of brain-based learning on students' academic achievement and to examine with the meta-analytical method if there is a significant difference in effect in terms of the factors of education level, subject matter, sampling size, and the…

  7. Standard guide for establishing a quality assurance program for analytical chemistry laboratories within the nuclear industry

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2006-01-01

    1.1 This guide covers the establishment of a quality assurance (QA) program for analytical chemistry laboratories within the nuclear industry. Reference to key elements of ANSI/ISO/ASQC Q9001, Quality Systems, provides guidance to the functional aspects of analytical laboratory operation. When implemented as recommended, the practices presented in this guide will provide a comprehensive QA program for the laboratory. The practices are grouped by functions, which constitute the basic elements of a laboratory QA program. 1.2 The essential, basic elements of a laboratory QA program appear in the following order: Section Organization 5 Quality Assurance Program 6 Training and Qualification 7 Procedures 8 Laboratory Records 9 Control of Records 10 Control of Procurement 11 Control of Measuring Equipment and Materials 12 Control of Measurements 13 Deficiencies and Corrective Actions 14

  8. QA engineering for the LCP USA magnet manufacturers

    International Nuclear Information System (INIS)

    Childress, C.E.; Batey, J.E.; Burn, P.B.

    1981-01-01

    This paper describes the QA and QC efforts and results used in fabricating the superconducting magnets of competing designs being developed by American Manufacturers for testing in the ORNL Large Coil Test Facility. Control of the design, materials and processes to assure proper functioning of the magnets in the test facility as well as the content of archival data being compiled is discussed

  9. Discussion of QA grading for AP1000 NP plant

    International Nuclear Information System (INIS)

    Luo Shuiyun; Zhang Qingchuan

    2012-01-01

    The grading method of quality assurance for the following AP1000 project is presented based on the Westinghouse classification principle, referring to the classification method of the AP1000 self-reliance supporting project and considering the factors of classification, which can meet the requirements of domestic nuclear safety regulation and standard of the QA classification. (authors)

  10. Q&A: Grace Anne Koppel, Living Well with COPD

    Science.gov (United States)

    ... their own lives back is the most rewarding thing we have ever done. Read More "The Challenge of COPD" Articles Q&A: Grace Anne Koppel, Living Well with COPD / What is COPD? / What Causes COPD? / Getting Tested / Am I at Risk? / COPD Quiz Fall ...

  11. Q&A: The Basics of California's School Finance System

    Science.gov (United States)

    EdSource, 2006

    2006-01-01

    In a state as large and complex as California, education financing can become as complicated as rocket science. This two-page Q&A provides a brief, easy-to-understand explanation of California's school finance system and introduces the issues of its adequacy and equity. A list of resources providing additional information is provided.

  12. A community Q&A for HEP Software and Computing ?

    CERN Multimedia

    CERN. Geneva

    2016-01-01

    How often do you use StackOverflow or ServerFault to find information in your daily work? Would you be interested in a community Q&A site for HEP Software and Computing, for instance a dedicated StackExchange site? I looked into this question...

  13. Biogeography of amphibians and reptiles in Arizona

    Science.gov (United States)

    Eric W. Stitt; Theresa M. Mau-Crimmins; Don E. Swann

    2005-01-01

    We examined patterns of species richness for amphibians and reptiles in Arizona and evaluated patterns in species distribution between ecoregions based on species range size. In Arizona, the Sonoran Desert has the highest herpetofauna diversity, and the southern ecoregions are more similar than other regions. There appear to be distinct low- and mid-elevational...

  14. An analytical study of photoacoustic and thermoacoustic generation efficiency towards contrast agent and film design optimization

    Directory of Open Access Journals (Sweden)

    Fei Gao

    2017-09-01

    Full Text Available Photoacoustic (PA and thermoacoustic (TA effects have been explored in many applications, such as bio-imaging, laser-induced ultrasound generator, and sensitive electromagnetic (EM wave film sensor. In this paper, we propose a compact analytical PA/TA generation model to incorporate EM, thermal and mechanical parameters, etc. From the derived analytical model, both intuitive predictions and quantitative simulations are performed. It shows that beyond the EM absorption improvement, there are many other physical parameters that deserve careful consideration when designing contrast agents or film composites, followed by simulation study. Lastly, several sets of experimental results are presented to prove the feasibility of the proposed analytical model. Overall, the proposed compact model could work as a clear guidance and predication for improved PA/TA contrast agents and film generator/sensor designs in the domain area.

  15. Notes on analytical study of holographic superconductors with Lifshitz scaling in external magnetic field

    International Nuclear Information System (INIS)

    Zhao, Zixu; Pan, Qiyuan; Jing, Jiliang

    2014-01-01

    We employ the matching method to analytically investigate the holographic superconductors with Lifshitz scaling in an external magnetic field. We discuss systematically the restricted conditions for the matching method and find that this analytic method is not always powerful to explore the effect of external magnetic field on the holographic superconductors unless the matching point is chosen in an appropriate range and the dynamical exponent z satisfies the relation z=d−1 or z=d−2. From the analytic treatment, we observe that Lifshitz scaling can hinder the condensation to be formed, which can be used to back up the numerical results. Moreover, we study the effect of Lifshitz scaling on the upper critical magnetic field and reproduce the well-known relation obtained from Ginzburg–Landau theory

  16. Analytical study of synchronization in spin-transfer-driven magnetization dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Bonin, Roberto [Politecnico di Torino - sede di Verres, via Luigi Barone 8, I-11029 Verres (Italy); Bertotti, Giorgio; Bortolotti, Paolo [Istituto Nazionale di Ricerca Metrologica, Strada delle Cacce 91, I-10135 Torino (Italy); Serpico, Claudio [Dipartimento di Ingegneria Elettrica, Universita di Napoli ' Federico II' , via Claudio 21, I-80125 Napoli (Italy); D' Aquino, Massimiliano [Dipartimento per le Tecnologie, Universita di Napoli ' Parthenope' , via Medina 40, I-80133 Napoli (Italy); Mayergoyz, Isaak D, E-mail: p.bortolotti@inrim.i [Electrical and Computer Engineering Department and UMIACS, University of Maryland, College Park MD 20742 (United States)

    2010-01-01

    An analytical study of the synchronization effects in spin-transfer-driven nanomagnets subjected to either microwave magnetic fields or microwave electrical currents is discussed. Appropriate stability diagrams are constructed and the conditions under which the current-induced magnetization precession is synchronized by the microwave external excitation are derived and discussed. Analytical predictions are given for the existence of phase-locking effects in current-induced magnetization precessions and for the occurrence of hysteresis in phase-locking as a function of the spin-polarized current.

  17. A semi-analytical study on helical springs made of shape memory polymer

    International Nuclear Information System (INIS)

    Baghani, M; Naghdabadi, R; Arghavani, J

    2012-01-01

    In this paper, the responses of shape memory polymer (SMP) helical springs under axial force are studied both analytically and numerically. In the analytical solution, we first derive the response of a cylindrical tube under torsional loadings. This solution can be used for helical springs in which both the curvature and pitch effects are negligible. This is the case for helical springs with large ratios of the mean coil radius to the cross sectional radius (spring index) and also small pitch angles. Making use of this solution simplifies the analysis of the helical springs to that of the torsion of a straight bar with circular cross section. The 3D phenomenological constitutive model recently proposed for SMPs is also reduced to the 1D shear case. Thus, an analytical solution for the torsional response of SMP tubes in a full cycle of stress-free strain recovery is derived. In addition, the curvature effect is added to the formulation and the SMP helical spring is analyzed using the exact solution presented for torsion of curved SMP tubes. In this modified solution, the effect of the direct shear force is also considered. In the numerical analysis, the 3D constitutive equations are implemented in a finite element program and a full cycle of stress-free strain recovery of an SMP (extension or compression) helical spring is simulated. Analytical and numerical results are compared and it is shown that the analytical solution gives accurate stress distributions in the cross section of the helical SMP spring besides the global load–deflection response. Some case studies are presented to show the validity of the presented analytical method. (paper)

  18. Designing Robust Process Analytical Technology (PAT) Systems for Crystallization Processes: A Potassium Dichromate Crystallization Case Study

    DEFF Research Database (Denmark)

    Abdul Samad, Noor Asma Fazli Bin; Sin, Gürkan

    2013-01-01

    The objective of this study is to test and validate a Process Analytical Technology (PAT) system design on a potassium dichromate crystallization process in the presence of input uncertainties using uncertainty and sensitivity analysis. To this end a systematic framework for managing uncertaintie...

  19. Experimental and analytical study on removal of strontium from cultivated soil

    International Nuclear Information System (INIS)

    Fukutani, Satoshi; Takahashi, Tomoyuki

    2003-01-01

    Experimental and analytical study was done to estimate the removal of strontium from cultivated soil. The continuous batch tests were made and uneasy desorption form or immobility form was proved to exist. 2-Component Model, which considers easy desorption and uneasy desorption form fraction, was constructed and it showed good explanation of the continuous batch test results. (author)

  20. Measuring Students' Writing Ability on a Computer-Analytic Developmental Scale: An Exploratory Validity Study

    Science.gov (United States)

    Burdick, Hal; Swartz, Carl W.; Stenner, A. Jackson; Fitzgerald, Jill; Burdick, Don; Hanlon, Sean T.

    2013-01-01

    The purpose of the study was to explore the validity of a novel computer-analytic developmental scale, the Writing Ability Developmental Scale. On the whole, collective results supported the validity of the scale. It was sensitive to writing ability differences across grades and sensitive to within-grade variability as compared to human-rated…

  1. Developing a Model and Applications for Probabilities of Student Success: A Case Study of Predictive Analytics

    Science.gov (United States)

    Calvert, Carol Elaine

    2014-01-01

    This case study relates to distance learning students on open access courses. It demonstrates the use of predictive analytics to generate a model of the probabilities of success and retention at different points, or milestones, in a student journey. A core set of explanatory variables has been established and their varying relative importance at…

  2. Analyzing Security Breaches in the U.S.: A Business Analytics Case-Study

    Science.gov (United States)

    Parks, Rachida F.; Adams, Lascelles

    2016-01-01

    This is a real-world applicable case-study and includes background information, functional organization requirements, and real data. Business analytics has been defined as the technologies, skills, and practices needed to iteratively investigate historical performance to gain insight or spot trends. You are asked to utilize/apply critical thinking…

  3. SU-E-T-760: Tolerance Design for Site-Specific Range in Proton Patient QA Process Using the Six Sigma Model

    International Nuclear Information System (INIS)

    Lah, J; Shin, D; Kim, G

    2015-01-01

    Purpose: To show how tolerance design and tolerancing approaches can be used to predict and improve the site-specific range in patient QA process in implementing the Six Sigma. Methods: In this study, patient QA plans were selected according to 6 site-treatment groups: head &neck (94 cases), spine (76 cases), lung (89 cases), liver (53 cases), pancreas (55 cases), and prostate (121 cases), treated between 2007 and 2013. We evaluated a model of the Six Sigma that determines allowable deviations in design parameters and process variables in patient-specific QA, where possible, tolerance may be loosened, then customized if it necessary to meet the functional requirements. A Six Sigma problem-solving methodology is known as DMAIC phases, which are used stand for: Define a problem or improvement opportunity, Measure process performance, Analyze the process to determine the root causes of poor performance, Improve the process by fixing root causes, Control the improved process to hold the gains. Results: The process capability for patient-specific range QA is 0.65 with only ±1 mm of tolerance criteria. Our results suggested the tolerance level of ±2–3 mm for prostate and liver cases and ±5 mm for lung cases. We found that customized tolerance between calculated and measured range reduce that patient QA plan failure and almost all sites had failure rates less than 1%. The average QA time also improved from 2 hr to less than 1 hr for all including planning and converting process, depth-dose measurement and evaluation. Conclusion: The objective of tolerance design is to achieve optimization beyond that obtained through QA process improvement and statistical analysis function detailing to implement a Six Sigma capable design

  4. SU-E-T-760: Tolerance Design for Site-Specific Range in Proton Patient QA Process Using the Six Sigma Model

    Energy Technology Data Exchange (ETDEWEB)

    Lah, J [Myongji Hospital, Goyang, Gyeonggi-do (Korea, Republic of); Shin, D [National Cancer Center, Goyang-si, Gyeonggi-do (Korea, Republic of); Kim, G [University of California, San Diego, La Jolla, CA (United States)

    2015-06-15

    Purpose: To show how tolerance design and tolerancing approaches can be used to predict and improve the site-specific range in patient QA process in implementing the Six Sigma. Methods: In this study, patient QA plans were selected according to 6 site-treatment groups: head &neck (94 cases), spine (76 cases), lung (89 cases), liver (53 cases), pancreas (55 cases), and prostate (121 cases), treated between 2007 and 2013. We evaluated a model of the Six Sigma that determines allowable deviations in design parameters and process variables in patient-specific QA, where possible, tolerance may be loosened, then customized if it necessary to meet the functional requirements. A Six Sigma problem-solving methodology is known as DMAIC phases, which are used stand for: Define a problem or improvement opportunity, Measure process performance, Analyze the process to determine the root causes of poor performance, Improve the process by fixing root causes, Control the improved process to hold the gains. Results: The process capability for patient-specific range QA is 0.65 with only ±1 mm of tolerance criteria. Our results suggested the tolerance level of ±2–3 mm for prostate and liver cases and ±5 mm for lung cases. We found that customized tolerance between calculated and measured range reduce that patient QA plan failure and almost all sites had failure rates less than 1%. The average QA time also improved from 2 hr to less than 1 hr for all including planning and converting process, depth-dose measurement and evaluation. Conclusion: The objective of tolerance design is to achieve optimization beyond that obtained through QA process improvement and statistical analysis function detailing to implement a Six Sigma capable design.

  5. An analytical study on groundwater flow in drainage basins with horizontal wells

    Science.gov (United States)

    Wang, Jun-Zhi; Jiang, Xiao-Wei; Wan, Li; Wang, Xu-Sheng; Li, Hailong

    2014-06-01

    Analytical studies on release/capture zones are often limited to a uniform background groundwater flow. In fact, for basin-scale problems, the undulating water table would lead to the development of hierarchically nested flow systems, which are more complex than a uniform flow. Under the premise that the water table is a replica of undulating topography and hardly influenced by wells, an analytical solution of hydraulic head is derived for a two-dimensional cross section of a drainage basin with horizontal injection/pumping wells. Based on the analytical solution, distributions of hydraulic head, stagnation points and flow systems (including release/capture zones) are explored. The superposition of injection/pumping wells onto the background flow field leads to the development of new internal stagnation points and new flow systems (including release/capture zones). Generally speaking, the existence of n injection/pumping wells would result in up to n new internal stagnation points and up to 2n new flow systems (including release/capture zones). The analytical study presented, which integrates traditional well hydraulics with the theory of regional groundwater flow, is useful in understanding basin-scale groundwater flow influenced by human activities.

  6. SU-E-T-11: A Cloud Based CT and LINAC QA Data Management System

    Energy Technology Data Exchange (ETDEWEB)

    Wiersma, R; Grelewicz, Z; Belcher, A; Liu, X [The University of Chicago, Chicago, IL (United States)

    2015-06-15

    Purpose: The current status quo of QA data management consists of a mixture of paper-based forms and spreadsheets for recording the results of daily, monthly, and yearly QA tests for both CT scanners and LINACs. Unfortunately, such systems suffer from a host of problems as, (1) records can be easily lost or destroyed, (2) data is difficult to access — one must physically hunt down records, (3) poor or no means of historical data analysis, and (4) no remote monitoring of machine performance off-site. To address these issues, a cloud based QA data management system was developed and implemented. Methods: A responsive tablet interface that optimizes clinic workflow with an easy-to-navigate interface accessible from any web browser was implemented in HTML/javascript/CSS to allow user mobility when entering QA data. Automated image QA was performed using a phantom QA kit developed in Python that is applicable to any phantom and is currently being used with the Gammex ACR, Las Vegas, Leeds, and Catphan phantoms for performing automated CT, MV, kV, and CBCT QAs, respectively. A Python based resource management system was used to distribute and manage intensive CPU tasks such as QA phantom image analysis or LaTeX-to-PDF QA report generation to independent process threads or different servers such that website performance is not affected. Results: To date the cloud QA system has performed approximately 185 QA procedures. Approximately 200 QA parameters are being actively tracked by the system on a monthly basis. Electronic access to historical QA parameter information was successful in proactively identifying a Linac CBCT scanner’s performance degradation. Conclusion: A fully comprehensive cloud based QA data management system was successfully implemented for the first time. Potential machine performance issues were proactively identified that would have been otherwise missed by a paper or spreadsheet based QA system.

  7. SU-E-T-11: A Cloud Based CT and LINAC QA Data Management System

    International Nuclear Information System (INIS)

    Wiersma, R; Grelewicz, Z; Belcher, A; Liu, X

    2015-01-01

    Purpose: The current status quo of QA data management consists of a mixture of paper-based forms and spreadsheets for recording the results of daily, monthly, and yearly QA tests for both CT scanners and LINACs. Unfortunately, such systems suffer from a host of problems as, (1) records can be easily lost or destroyed, (2) data is difficult to access — one must physically hunt down records, (3) poor or no means of historical data analysis, and (4) no remote monitoring of machine performance off-site. To address these issues, a cloud based QA data management system was developed and implemented. Methods: A responsive tablet interface that optimizes clinic workflow with an easy-to-navigate interface accessible from any web browser was implemented in HTML/javascript/CSS to allow user mobility when entering QA data. Automated image QA was performed using a phantom QA kit developed in Python that is applicable to any phantom and is currently being used with the Gammex ACR, Las Vegas, Leeds, and Catphan phantoms for performing automated CT, MV, kV, and CBCT QAs, respectively. A Python based resource management system was used to distribute and manage intensive CPU tasks such as QA phantom image analysis or LaTeX-to-PDF QA report generation to independent process threads or different servers such that website performance is not affected. Results: To date the cloud QA system has performed approximately 185 QA procedures. Approximately 200 QA parameters are being actively tracked by the system on a monthly basis. Electronic access to historical QA parameter information was successful in proactively identifying a Linac CBCT scanner’s performance degradation. Conclusion: A fully comprehensive cloud based QA data management system was successfully implemented for the first time. Potential machine performance issues were proactively identified that would have been otherwise missed by a paper or spreadsheet based QA system

  8. Study on the application of quality assurance in research and development

    Energy Technology Data Exchange (ETDEWEB)

    Kwon, Hyuk Il; Lim, Kap Soon; Lee, Young Keun; Lim, Nam Jin; Cho, Moon Seong; Choi, Se Jin; Won, Byung Chool; Kwon, Woo Ju; Lee, Jae Hyung [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1995-12-01

    Application status of R and D QA system in advanced research organizations abroad was studied and related information were reviewed. On these bases, KAERI R and D QA system and detailed instructions for R and D projects were trained with the system. Especially for three of the five demo projects, project specific QA programs were developed in accordance with project types. Besides, the 1st Nuclear QA seminar and other events such as `Seminar on Adopting Quality Management in an R and D Environment` were held for the purpose of assisting QA implementation in demo projects as well as enhancing researchers` perceptions on QA. Based on these activities, measures for QA application in R and D were suggested, which include R and D QA document hierarchy, determination of the scope of QA application, and QA activities in project performance stage and appraisal stage. 4 tabs., 12 figs., 13 refs. (Author).

  9. IMRT QA using machine learning: A multi-institutional validation.

    Science.gov (United States)

    Valdes, Gilmer; Chan, Maria F; Lim, Seng Boh; Scheuermann, Ryan; Deasy, Joseph O; Solberg, Timothy D

    2017-09-01

    To validate a machine learning approach to Virtual intensity-modulated radiation therapy (IMRT) quality assurance (QA) for accurately predicting gamma passing rates using different measurement approaches at different institutions. A Virtual IMRT QA framework was previously developed using a machine learning algorithm based on 498 IMRT plans, in which QA measurements were performed using diode-array detectors and a 3%local/3 mm with 10% threshold at Institution 1. An independent set of 139 IMRT measurements from a different institution, Institution 2, with QA data based on portal dosimetry using the same gamma index, was used to test the mathematical framework. Only pixels with ≥10% of the maximum calibrated units (CU) or dose were included in the comparison. Plans were characterized by 90 different complexity metrics. A weighted poison regression with Lasso regularization was trained to predict passing rates using the complexity metrics as input. The methodology predicted passing rates within 3% accuracy for all composite plans measured using diode-array detectors at Institution 1, and within 3.5% for 120 of 139 plans using portal dosimetry measurements performed on a per-beam basis at Institution 2. The remaining measurements (19) had large areas of low CU, where portal dosimetry has a larger disagreement with the calculated dose and as such, the failure was expected. These beams need further modeling in the treatment planning system to correct the under-response in low-dose regions. Important features selected by Lasso to predict gamma passing rates were as follows: complete irradiated area outline (CIAO), jaw position, fraction of MLC leafs with gaps smaller than 20 or 5 mm, fraction of area receiving less than 50% of the total CU, fraction of the area receiving dose from penumbra, weighted average irregularity factor, and duty cycle. We have demonstrated that Virtual IMRT QA can predict passing rates using different measurement techniques and across multiple

  10. A European multicenter study on the analytical performance of the VERIS HBV assay.

    Science.gov (United States)

    Braun, Patrick; Delgado, Rafael; Drago, Monica; Fanti, Diana; Fleury, Hervé; Izopet, Jacques; Lombardi, Alessandra; Mancon, Alessandro; Marcos, Maria Angeles; Sauné, Karine; O Shea, Siobhan; Pérez-Rivilla, Alfredo; Ramble, John; Trimoulet, Pascale; Vila, Jordi; Whittaker, Duncan; Artus, Alain; Rhodes, Daniel

    Hepatitis B viral load monitoring is an essential part of managing patients with chronic Hepatits B infection. Beckman Coulter has developed the VERIS HBV Assay for use on the fully automated Beckman Coulter DxN VERIS Molecular Diagnostics System. 1 OBJECTIVES: To evaluate the analytical performance of the VERIS HBV Assay at multiple European virology laboratories. Precision, analytical sensitivity, negative sample performance, linearity and performance with major HBV genotypes/subtypes for the VERIS HBV Assay was evaluated. Precision showed an SD of 0.15 log 10 IU/mL or less for each level tested. Analytical sensitivity determined by probit analysis was between 6.8-8.0 IU/mL. Clinical specificity on 90 unique patient samples was 100.0%. Performance with 754 negative samples demonstrated 100.0% not detected results, and a carryover study showed no cross contamination. Linearity using clinical samples was shown from 1.23-8.23 log 10 IU/mL and the assay detected and showed linearity with major HBV genotypes/subtypes. The VERIS HBV Assay demonstrated comparable analytical performance to other currently marketed assays for HBV DNA monitoring. Copyright © 2017 Elsevier B.V. All rights reserved.

  11. A study on improvement of analytical prediction model for spacer grid pressure loss coefficients

    International Nuclear Information System (INIS)

    Lim, Jonh Seon

    2002-02-01

    Nuclear fuel assemblies used in the nuclear power plants consist of the nuclear fuel rods, the control rod guide tubes, an instrument guide tube, spacer grids,a bottom nozzle, a top nozzle. The spacer grid is the most important component of the fuel assembly components for thermal hydraulic and mechanical design and analyses. The spacer grids fixed with the guide tubes support the fuel rods and have the very important role to activate thermal energy transfer by the coolant mixing caused to the turbulent flow and crossflow in the subchannels. In this paper, the analytical spacer grid pressure loss prediction model has been studied and improved by considering the test section wall to spacer grid gap pressure loss independently and applying the appropriate friction drag coefficient to predict pressure loss more accurately at the low Reynolds number region. The improved analytical model has been verified based on the hydraulic pressure drop test results for the spacer grids of three types with 5x5, 16x16, 17x17 arrays, respectively. The pressure loss coefficients predicted by the improved analytical model are coincident with those test results within ±12%. This result shows that the improved analytical model can be used for research and design change of the nuclear fuel assembly

  12. Analytic method study of point-reactor kinetic equation when cold start-up

    International Nuclear Information System (INIS)

    Zhang Fan; Chen Wenzhen; Gui Xuewen

    2008-01-01

    The reactor cold start-up is a process of inserting reactivity by lifting control rod discontinuously. Inserting too much reactivity will cause short-period and may cause an overpressure accident in the primary loop. It is therefore very important to understand the rule of neutron density variation and to find out the relationships among the speed of lifting control rod, and the duration and speed of neutron density response. It is also helpful for the operators to grasp the rule in order to avoid a start-up accident. This paper starts with one-group delayed neutron point-reactor kinetics equations and provides their analytic solution when reactivity is introduced by lifting control rods discontinuously. The analytic expression is validated by comparison with practical data. It is shown that the analytic solution agrees well with numerical solution. Using this analytical solution, the relationships among neutron density response with the speed of lifting control rod and its duration are also studied. By comparing the results with those under the condition of step inserted reactivity, useful conclusions are drawn

  13. Noble gas encapsulation into carbon nanotubes: Predictions from analytical model and DFT studies

    Energy Technology Data Exchange (ETDEWEB)

    Balasubramani, Sree Ganesh; Singh, Devendra; Swathi, R. S., E-mail: swathi@iisertvm.ac.in [School of Chemistry, Indian Institute of Science Education and Research Thiruvananthapuram (IISER-TVM), Kerala 695016 (India)

    2014-11-14

    The energetics for the interaction of the noble gas atoms with the carbon nanotubes (CNTs) are investigated using an analytical model and density functional theory calculations. Encapsulation of the noble gas atoms, He, Ne, Ar, Kr, and Xe into CNTs of various chiralities is studied in detail using an analytical model, developed earlier by Hill and co-workers. The constrained motion of the noble gas atoms along the axes of the CNTs as well as the off-axis motion are discussed. Analyses of the forces, interaction energies, acceptance and suction energies for the encapsulation enable us to predict the optimal CNTs that can encapsulate each of the noble gas atoms. We find that CNTs of radii 2.98 − 4.20 Å (chiral indices, (5,4), (6,4), (9,1), (6,6), and (9,3)) can efficiently encapsulate the He, Ne, Ar, Kr, and Xe atoms, respectively. Endohedral adsorption of all the noble gas atoms is preferred over exohedral adsorption on various CNTs. The results obtained using the analytical model are subsequently compared with the calculations performed with the dispersion-including density functional theory at the M06 − 2X level using a triple-zeta basis set and good qualitative agreement is found. The analytical model is however found to be computationally cheap as the equations can be numerically programmed and the results obtained in comparatively very less time.

  14. Application of nuclear analytical methods to heavy metal pollution studies of estuaries

    International Nuclear Information System (INIS)

    Anders, B.; Junge, W.; Knoth, J.; Michaelis, W.; Pepelnik, R.; Schwenke, H.

    1984-01-01

    Important objectives of heavy metal pollution studies of estuaries are the understanding of the transport phenomena in these complex ecosystems and the discovery of the pollution history and the geochemical background. Such studies require high precision and accuracy of the analytical methods. Moreover, pronounced spatial heterogeneities and temporal variabilities that are typical for estuaries necessitate the analysis of a great number of samples if relevant results are to be obtained. Both requirements can economically be fulfilled by a proper combination of analytical methods. Applications of energy-dispersive X-ray fluorescence analysis with total reflection of the exciting beam at the sample support and of neutron activation analysis with both thermal and fast neutrons are reported in the light of pollution studies performed in the Lower Elbe River. (orig.)

  15. Application of nuclear analytical methods to heavy metal pollution studies of estuaries

    International Nuclear Information System (INIS)

    Anders, B.; Junge, W.; Knoth, J.; Michaelis, W.; Pepelnik, R.; Schwenke, H.

    1984-01-01

    Important objectives of heavy metal pollution studies of estuaries are the understanding of the transport phenomena in these complex ecosystems and the discovery of the pollution history and the geochemical background. Such studies require high precision and accuracy of the analytical methods. Moreover, pronounced spatial heterogeneities and temporal variabilities that are typical for estuaries necessitate the analysis of a great number of samples if relevant results are to be obtained. Both requirements can economically be fulfilled by a proper combination of analytical methods. Applications of energy-dispersive X-ray fluorescence analysis with total reflection of the exciting beam at the sample support and of neutron activation analysis with both thermal and fast neutrons are reported in the light of pollution studies performed in the Lower Elbe River. Profiles are presented for the total heavy metal content determined from particulate matter and sediment. They include V, Mn, Fe, Ni, Cu, Zn, As, Pb, and Cd. 16 references 10 figures, 1 table

  16. Final report of “A Detailed Study of the Physical Mechanisms Controlling CO2-Brine Capillary Trapping in the Subsurface” (University of Arizona, DE-SC0006696)

    Energy Technology Data Exchange (ETDEWEB)

    Schaap, Marcel G. [Univ. of Arizona, Tucson, AZ (United States)

    2016-07-25

    Carbon capture and storage (CCS) of carbon dioxide emissions generated by production or combustion of fossil fuels is a technologically viable means to reduce the build-up of CO2 in the atmosphere and oceans. Using advantages of scale and location, CCS is particularly suitable for large point sources near ubiquitous deep saline aquifers, depleted gas reservoirs, or at production reservoirs for enhanced oil recovery (EOR). In the BES-funded research project, Oregon State University (OSU) carried out capillary trapping experiments with proxy fluids that mimic the properties of the scCO2/brine system under ambient temperatures and pressures, and successfully developed a unique and novel x-ray compatible, high-pressure, elevated temperature setup to study the scCO2/brine system under challenging reservoir conditions. Both methodologies were applied to a variety of porous media, including synthetic (glass bead) and geologic (Bentheimer sandstone) materials. The University of Arizona (UA) developed pore-scale lattice Boltzmann (LB) models which are able to handle the experimental conditions for proxy fluids, as well as the scCO2/brine system, that are capable of simulating permeability in volumes of tens of millions of fluid elements. We reached the following summary findings (main institute indicated): 1. (OSU/UA) To understand capillary trapping in a multiphase fluid-porous medium system, the system must be analyzed from a pore-scale force balance perspective; trapping can be enhanced by manipulating wetting and nonwetting phase fluid properties. 2. (OSU) Pore-scale fluid connectivity and topology has a clear and direct effect on nonwetting phase capillary trapping efficiency. 3. (OSU) Rock type and flow regime also have a pronounced effects on capillary trapping. 4. (OSU/UA) There is a predictable relationship between NWP connectivity and NWP saturation, which allows for development of injection strategies that optimize trapping. The commonly used Land model (Land

  17. Analytical and biological studies of kanji and extracts of its ingredient, daucus carota L

    International Nuclear Information System (INIS)

    Latif, A.; Hussain, K.; Bukhari, N.; Karim, S.; Hussain, A.; Khurshid, F.

    2013-01-01

    A fermented beverage, Kanji, prepared from roots of Daucus carota L. subsp. sativus (Hoffm.) Arcang. var. vavilovii Mazk. (Apiaceae), despite long usage history has not been investigated for analytical studies and biological activities. Therefore, the present study aimed to investigate different types of Kanji samples and various types of extracts/fractions of root of the plant for a number of analytical studies and in vitro antioxidant activities. The Kanji sample, Lab-made Kanji, having better analytical and biological profile was further investigated for preliminary clinical studies. The analytical studies indicated that Lab-made Kanji was having comparatively higher contents of phytochemicals than that of the commercial Kanji samples, different types of extracts and fractions (P < 0.05). All the Kanji samples and aqueous and ethanol extracts of fresh roots exhibited comparable antioxidant activities in DPPH assay (52.20 - 54.19%) that were higher than that of methanol extract (48.78%) of dried roots. The antiradical powers (1/ EC50) of Lab-made Kanji and aqueous extract were found to be higher than that of the ethanol and methanol extracts. In beta-carotene linoleate assay, the Kanji samples showed higher activity than that of the methanol extract, but comparable to that of the vitamin-E and butylated hydroxyl anisole (BHA) (P < 0.05). A preliminary clinical evaluation indicated that Kanji has no harmful effect on blood components, liver function and serum lipid profile. The results of the present study indicate that Kanji is an effective antioxidant beverage. (author)

  18. Experimental and analytical studies of high heat flux components for fusion experimental reactor

    International Nuclear Information System (INIS)

    Araki, Masanori

    1993-03-01

    In this report, the experimental and analytical results concerning the development of plasma facing components of ITER are described. With respect to developing high heat removal structures for the divertor plates, an externally-finned swirl tube was developed based on the results of critical heat flux (CHF) experiments on various tube structures. As the result, the burnout heat flux, which also indicates incident CHF, of 41 ± 1 MW/m 2 was achieved in the externally-finned swirl tube. The applicability of existing CHF correlations based on uniform heating conditions was evaluated by comparing the CHF experimental data with the smooth and the externally-finned tubes under one-sided heating condition. As the results, experimentally determined CHF data for straight tube show good agreement, for the externally-finned tube, no existing correlations are available for prediction of the CHF. With respect to the evaluation of the bonds between carbon-based material and heat sink metal, results of brazing tests were compared with the analytical results by three dimensional model with temperature-dependent thermal and mechanical properties. Analytical results showed that residual stresses from brazing can be estimated by the analytical three directional stress values instead of the equivalent stress value applied. In the analytical study on the separatrix sweeping for effectively reducing surface heat fluxes on the divertor plate, thermal response of the divertor plate has been analyzed under ITER relevant heat flux conditions and has been tested. As the result, it has been demonstrated that application of the sweeping technique is very effective for improvement in the power handling capability of the divertor plate and that the divertor mock-up has withstood a large number of additional cyclic heat loads. (J.P.N.) 62 refs

  19. QA [quality assurance] at Fermilab; the hermeneutics of NQA-1

    International Nuclear Information System (INIS)

    Bodnarczuk, M.

    1988-06-01

    This paper opens with a brief overview of the purpose of Fermilab and a historical synopsis of the development and current status of quality assurance (QA) at the Laboratory. The paper subsequently addresses some of the more important aspects of interpreting the national standard ANSI/ASME NQA-1 in pure research environments like Fermilab. Highlights of this discussion include, what is hermeneutics and why are hermeneutical considerations relevant for QA, a critical analysis of NQA-1 focussing on teleological aspects of the standard, a description of the hermeneutical approach to NQA-1 used at Fermilab which attempts to capture the true intents of the document without violating the deeply ingrained traditions of quality standards and peer review that have been foundational to the overall success of the paradigms of high-energy physics

  20. QA (quality assurance) at Fermilab; the hermeneutics of NQA-1

    Energy Technology Data Exchange (ETDEWEB)

    Bodnarczuk, M.

    1988-06-01

    This paper opens with a brief overview of the purpose of Fermilab and a historical synopsis of the development and current status of quality assurance (QA) at the Laboratory. The paper subsequently addresses some of the more important aspects of interpreting the national standard ANSI/ASME NQA-1 in pure research environments like Fermilab. Highlights of this discussion include, what is hermeneutics and why are hermeneutical considerations relevant for QA, a critical analysis of NQA-1 focussing on teleological aspects of the standard, a description of the hermeneutical approach to NQA-1 used at Fermilab which attempts to capture the true intents of the document without violating the deeply ingrained traditions of quality standards and peer review that have been foundational to the overall success of the paradigms of high-energy physics.

  1. SU-F-T-459: ArcCHECK Machine QA : Highly Efficient Quality Assurance Tool for VMAT, SRS & SBRT Linear Accelerator Delivery

    International Nuclear Information System (INIS)

    Mhatre, V; Patwe, P; Dandekar, P

    2016-01-01

    Purpose: Quality assurance (QA) of complex linear accelerators is critical and highly time consuming. ArcCHECK Machine QA tool is used to test geometric and delivery aspects of linear accelerator. In this study we evaluated the performance of this tool. Methods: Machine QA feature allows user to perform quality assurance tests using ArcCHECK phantom. Following tests were performed 1) Gantry Speed 2) Gantry Rotation 3) Gantry Angle 4)MLC/Collimator QA 5)Beam Profile Flatness & Symmetry. Data was collected on trueBEAM stX machine for 6 MV for a period of one year. The Gantry QA test allows to view errors in gantry angle, rotation & assess how accurately the gantry moves around the isocentre. The MLC/Collimator QA tool is used to analyze & locate the differences between leaf bank & jaw position of linac. The flatness & Symmetry test quantifies beam flatness & symmetry in IEC-y & x direction. The Gantry & Flatness/Symmetry test can be performed for static & dynamic delivery. Results: The Gantry speed was 3.9 deg/sec with speed maximum deviation around 0.3 deg/sec. The Gantry Isocentre for arc delivery was 0.9mm & static delivery was 0.4mm. The maximum percent positive & negative difference was found to be 1.9 % & – 0.25 % & maximum distance positive & negative diff was 0.4mm & – 0.3 mm for MLC/Collimator QA. The Flatness for Arc delivery was 1.8 % & Symmetry for Y was 0.8 % & X was 1.8 %. The Flatness for gantry 0°,270°,90° & 180° was 1.75,1.9,1.8 & 1.6% respectively & Symmetry for X & Y was 0.8,0.6% for 0°, 0.6,0.7% for 270°, 0.6,1% for 90° & 0.6,0.7% for 180°. Conclusion: ArcCHECK Machine QA is an useful tool for QA of Modern linear accelerators as it tests both geometric & delivery aspects. This is very important for VMAT, SRS & SBRT treatments.

  2. SU-F-T-459: ArcCHECK Machine QA : Highly Efficient Quality Assurance Tool for VMAT, SRS & SBRT Linear Accelerator Delivery

    Energy Technology Data Exchange (ETDEWEB)

    Mhatre, V; Patwe, P; Dandekar, P [Sir HN RF Hospital, Mumbai, Maharashtra (India)

    2016-06-15

    Purpose: Quality assurance (QA) of complex linear accelerators is critical and highly time consuming. ArcCHECK Machine QA tool is used to test geometric and delivery aspects of linear accelerator. In this study we evaluated the performance of this tool. Methods: Machine QA feature allows user to perform quality assurance tests using ArcCHECK phantom. Following tests were performed 1) Gantry Speed 2) Gantry Rotation 3) Gantry Angle 4)MLC/Collimator QA 5)Beam Profile Flatness & Symmetry. Data was collected on trueBEAM stX machine for 6 MV for a period of one year. The Gantry QA test allows to view errors in gantry angle, rotation & assess how accurately the gantry moves around the isocentre. The MLC/Collimator QA tool is used to analyze & locate the differences between leaf bank & jaw position of linac. The flatness & Symmetry test quantifies beam flatness & symmetry in IEC-y & x direction. The Gantry & Flatness/Symmetry test can be performed for static & dynamic delivery. Results: The Gantry speed was 3.9 deg/sec with speed maximum deviation around 0.3 deg/sec. The Gantry Isocentre for arc delivery was 0.9mm & static delivery was 0.4mm. The maximum percent positive & negative difference was found to be 1.9 % & – 0.25 % & maximum distance positive & negative diff was 0.4mm & – 0.3 mm for MLC/Collimator QA. The Flatness for Arc delivery was 1.8 % & Symmetry for Y was 0.8 % & X was 1.8 %. The Flatness for gantry 0°,270°,90° & 180° was 1.75,1.9,1.8 & 1.6% respectively & Symmetry for X & Y was 0.8,0.6% for 0°, 0.6,0.7% for 270°, 0.6,1% for 90° & 0.6,0.7% for 180°. Conclusion: ArcCHECK Machine QA is an useful tool for QA of Modern linear accelerators as it tests both geometric & delivery aspects. This is very important for VMAT, SRS & SBRT treatments.

  3. Experimental and analytical study of high velocity impact on Kevlar/Epoxy composite plates

    Science.gov (United States)

    Sikarwar, Rahul S.; Velmurugan, Raman; Madhu, Velmuri

    2012-12-01

    In the present study, impact behavior of Kevlar/Epoxy composite plates has been carried out experimentally by considering different thicknesses and lay-up sequences and compared with analytical results. The effect of thickness, lay-up sequence on energy absorbing capacity has been studied for high velocity impact. Four lay-up sequences and four thickness values have been considered. Initial velocities and residual velocities are measured experimentally to calculate the energy absorbing capacity of laminates. Residual velocity of projectile and energy absorbed by laminates are calculated analytically. The results obtained from analytical study are found to be in good agreement with experimental results. It is observed from the study that 0/90 lay-up sequence is most effective for impact resistance. Delamination area is maximum on the back side of the plate for all thickness values and lay-up sequences. The delamination area on the back is maximum for 0/90/45/-45 laminates compared to other lay-up sequences.

  4. Horizontal Parallel Pipe Ground Heat Exchanger : Analytical Conception and Experimental Study

    International Nuclear Information System (INIS)

    Naili, Nabiha; Jemli, Ramzi; Farhat, Abdel Hamid; Ben Nasrallah, Sassi

    2009-01-01

    Due to limited amount of natural resources exploited for heating, and in order to reduce the environmental impact, people should strive to use renewable energy resources. Ambient low-grade energy may be upgraded by the ground heat exchanger (GH E), which exploits the ground thermal inertia for buildings heating and cooling. In this study, analytical performance and experiments analysis of a horizontal ground heat exchanger have been performed. The analytical study, relates to the dimensioning of the heat exchanger, shows that the heat exchanger characteristics are very important for the determination of heat extracted from ground. The experimental results were obtained during the period 30 November to 10 December 2007, in the heating season of the greenhouses. Measurements show that the ground temperature under a certain depth remains relatively constant. To exploit effectively the heat capacity of the ground, a horizontal heat exchanger system has to be constructed and tested in the Center of Research and Technology of Energy, in Tunisia

  5. Analytic study for physical protection system (PPS) in nuclear power plants (NPPs)

    Energy Technology Data Exchange (ETDEWEB)

    Woo, Tae Ho, E-mail: thw@snu.ac.kr

    2013-12-15

    Highlights: • The physical protection system (PPS) is investigated. • General NPPs are modeled in the study. • Possible terror cases, likelihood, and consequence are studied. • PPS is constructed by analytical methods. - Abstract: The nuclear safeguard is analyzed in the aspect of the physical protection system (PPS) in nuclear power plants (NPPs). The PPS is reviewed and its related terror scenarios are investigated. The PPS is developed using analytical methods. In the terror scenarios, there are 8 possible cases for the terror attacks to the NPPs. Then, the likelihood of terror is classified by the general terror incidents. The consequence of terror is classified by Design Basis Threat (DBT) of the International Atomic Energy Agency (IAEA) scale. The physical protection method is suggested by defense-in-depth constraints and severe accident countermeasures. Finally, the advanced PPS is constructed, which could be used for the preparation for the possible terror attacks in the NPPs.

  6. Analytic study for physical protection system (PPS) in nuclear power plants (NPPs)

    International Nuclear Information System (INIS)

    Woo, Tae Ho

    2013-01-01

    Highlights: • The physical protection system (PPS) is investigated. • General NPPs are modeled in the study. • Possible terror cases, likelihood, and consequence are studied. • PPS is constructed by analytical methods. - Abstract: The nuclear safeguard is analyzed in the aspect of the physical protection system (PPS) in nuclear power plants (NPPs). The PPS is reviewed and its related terror scenarios are investigated. The PPS is developed using analytical methods. In the terror scenarios, there are 8 possible cases for the terror attacks to the NPPs. Then, the likelihood of terror is classified by the general terror incidents. The consequence of terror is classified by Design Basis Threat (DBT) of the International Atomic Energy Agency (IAEA) scale. The physical protection method is suggested by defense-in-depth constraints and severe accident countermeasures. Finally, the advanced PPS is constructed, which could be used for the preparation for the possible terror attacks in the NPPs

  7. Group-analytic training groups for psychology students: A qualitative study

    DEFF Research Database (Denmark)

    Nathan, Vibeke Torpe; Poulsen, Stig

    2004-01-01

    This article presents results from an interview study of psychology students' experiences from group-analytic groups conducted at the University of Copenhagen. The primary foci are the significance of differences in themotivation participants'  personal aims of individual participantsfor particip......This article presents results from an interview study of psychology students' experiences from group-analytic groups conducted at the University of Copenhagen. The primary foci are the significance of differences in themotivation participants'  personal aims of individual participantsfor...... participation in the group, the impact of the composition of participants on the group process, and the professional learning through the group experience. In general the interviews show a marked satisfaction with the group participation. In particular, learning about the importance of group boundaries...

  8. Analytical method validation for quality control and the study of the 50 mg Propylthiouracil stability

    International Nuclear Information System (INIS)

    Valdes Bendoyro, Maria Olga; Garcia Penna, Caridad Margarita; Fernandez, Juan Lugones; Garcia Borges, Lisandra; Martinez Espinosa, Vivian

    2010-01-01

    A high-performance liquid chromatography analytical method was developed and validated for the quality control and stability studies of 50 mg Propylthiouracil tablets. Method is based in active principle separation through a 100 RP-18 RP-18 (5 μm) (250 x 4 mm) Lichrospher chromatography with UV detection to 272 nm, using a mobile phase composed by a ungaseous mixture of a 0.025 M buffer solution-monobasic potassium phosphate to pH= 4,6 ad acetonitrile in a 80:20 ratio with a flux speed of 0,5 mL/min. Analytical method was linear, precise, specific and exact in the study concentrations interval

  9. USGS QA Plan: Certification of digital airborne mapping products

    Science.gov (United States)

    Christopherson, J.

    2007-01-01

    To facilitate acceptance of new digital technologies in aerial imaging and mapping, the US Geological Survey (USGS) and its partners have launched a Quality Assurance (QA) Plan for Digital Aerial Imagery. This should provide a foundation for the quality of digital aerial imagery and products. It introduces broader considerations regarding processes employed by aerial flyers in collecting, processing and delivering data, and provides training and information for US producers and users alike.

  10. QA/QC - Practices and procedures in WWER fuel management

    International Nuclear Information System (INIS)

    Keselica, M.

    1999-01-01

    Construction time schedule and commissioning (unit by unit) of the NPP Dukovany as well as structure of electricity generation in the CEZ in 1998 are reviewed. History of QA/QC system establishment and rules (system standards) as well as organization chart of the NPP Dukovany and quality manual of reactor physics department are presented. Standards of worker's qualification and nuclear fuel inspections are discussed. Fuel reliability indicators are presented

  11. Institutional Patient-specific IMRT QA Does Not Predict Unacceptable Plan Delivery

    Energy Technology Data Exchange (ETDEWEB)

    Kry, Stephen F., E-mail: sfkry@mdanderson.org [Imaging and Radiation Oncology Core at Houston, Department of Radiation Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Molineu, Andrea [Imaging and Radiation Oncology Core at Houston, Department of Radiation Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Kerns, James R.; Faught, Austin M.; Huang, Jessie Y.; Pulliam, Kiley B.; Tonigan, Jackie [Imaging and Radiation Oncology Core at Houston, Department of Radiation Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); The University of Texas Health Science Center Houston, Graduate School of Biomedical Sciences, Houston, Texas (United States); Alvarez, Paola [Imaging and Radiation Oncology Core at Houston, Department of Radiation Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Stingo, Francesco [The University of Texas Health Science Center Houston, Graduate School of Biomedical Sciences, Houston, Texas (United States); Department of Biostatistics, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); Followill, David S. [Imaging and Radiation Oncology Core at Houston, Department of Radiation Physics, The University of Texas MD Anderson Cancer Center, Houston, Texas (United States); The University of Texas Health Science Center Houston, Graduate School of Biomedical Sciences, Houston, Texas (United States)

    2014-12-01

    Purpose: To determine whether in-house patient-specific intensity modulated radiation therapy quality assurance (IMRT QA) results predict Imaging and Radiation Oncology Core (IROC)-Houston phantom results. Methods and Materials: IROC Houston's IMRT head and neck phantoms have been irradiated by numerous institutions as part of clinical trial credentialing. We retrospectively compared these phantom results with those of in-house IMRT QA (following the institution's clinical process) for 855 irradiations performed between 2003 and 2013. The sensitivity and specificity of IMRT QA to detect unacceptable or acceptable plans were determined relative to the IROC Houston phantom results. Additional analyses evaluated specific IMRT QA dosimeters and analysis methods. Results: IMRT QA universally showed poor sensitivity relative to the head and neck phantom, that is, poor ability to predict a failing IROC Houston phantom result. Depending on how the IMRT QA results were interpreted, overall sensitivity ranged from 2% to 18%. For different IMRT QA methods, sensitivity ranged from 3% to 54%. Although the observed sensitivity was particularly poor at clinical thresholds (eg 3% dose difference or 90% of pixels passing gamma), receiver operator characteristic analysis indicated that no threshold showed good sensitivity and specificity for the devices evaluated. Conclusions: IMRT QA is not a reasonable replacement for a credentialing phantom. Moreover, the particularly poor agreement between IMRT QA and the IROC Houston phantoms highlights surprising inconsistency in the QA process.

  12. Institutional Patient-specific IMRT QA Does Not Predict Unacceptable Plan Delivery

    International Nuclear Information System (INIS)

    Kry, Stephen F.; Molineu, Andrea; Kerns, James R.; Faught, Austin M.; Huang, Jessie Y.; Pulliam, Kiley B.; Tonigan, Jackie; Alvarez, Paola; Stingo, Francesco; Followill, David S.

    2014-01-01

    Purpose: To determine whether in-house patient-specific intensity modulated radiation therapy quality assurance (IMRT QA) results predict Imaging and Radiation Oncology Core (IROC)-Houston phantom results. Methods and Materials: IROC Houston's IMRT head and neck phantoms have been irradiated by numerous institutions as part of clinical trial credentialing. We retrospectively compared these phantom results with those of in-house IMRT QA (following the institution's clinical process) for 855 irradiations performed between 2003 and 2013. The sensitivity and specificity of IMRT QA to detect unacceptable or acceptable plans were determined relative to the IROC Houston phantom results. Additional analyses evaluated specific IMRT QA dosimeters and analysis methods. Results: IMRT QA universally showed poor sensitivity relative to the head and neck phantom, that is, poor ability to predict a failing IROC Houston phantom result. Depending on how the IMRT QA results were interpreted, overall sensitivity ranged from 2% to 18%. For different IMRT QA methods, sensitivity ranged from 3% to 54%. Although the observed sensitivity was particularly poor at clinical thresholds (eg 3% dose difference or 90% of pixels passing gamma), receiver operator characteristic analysis indicated that no threshold showed good sensitivity and specificity for the devices evaluated. Conclusions: IMRT QA is not a reasonable replacement for a credentialing phantom. Moreover, the particularly poor agreement between IMRT QA and the IROC Houston phantoms highlights surprising inconsistency in the QA process

  13. Analytical studies on a modified Nagel-Schreckenberg model with the Fukui-Ishibashi acceleration rule

    International Nuclear Information System (INIS)

    Fu Chuanji; Wang Binghong; Yin Chuanyang; Zhou Tao; Hu Bo; Gao Kun; Hui, P.M.; Hu, C.-K.

    2007-01-01

    We propose and study a one-dimensional traffic flow cellular automaton model of high-speed vehicles with the Fukui-Ishibashi-type (FI) acceleration rule for all cars, and the Nagel-Schreckenberg-type (NS) stochastic delay mechanism. We obtain analytically the fundamental diagrams of the average speed and vehicle flux depending on the vehicle density and stochastic delay probability. Our theoretical results are in excellent agreement with numerical simulations

  14. A functional-analytic method for the study of difference equations

    Directory of Open Access Journals (Sweden)

    Siafarikas Panayiotis D

    2004-01-01

    Full Text Available We will give the generalization of a recently developed functional-analytic method for studying linear and nonlinear, ordinary and partial, difference equations in the and spaces, p∈ℕ, . The method will be illustrated by use of two examples concerning a nonlinear ordinary difference equation known as the Putnam equation, and a linear partial difference equation of three variables describing the discrete Newton law of cooling in three dimensions.

  15. Analytical study for the ability of nonlinear transmission lines to generate solitons

    International Nuclear Information System (INIS)

    Mostafa, S.I.

    2009-01-01

    The ability of the nonlinear transmission lines (NLTL) has been studied analytically, in this paper to generate solitons and to cause waveform spreading. This can be achieved by balancing nonlinearity and dispersion. A new technique of improved tanh method (ITM) and improved sech methods (ISM) is applied to the nonlinear partial differential equation that describes the NLTL. It is found that the parameters of the transmission line play an important role in controlling the shape of the soliton.

  16. The role of nuclear analytical techniques in the study of aqueous corrosion of glasses

    International Nuclear Information System (INIS)

    Trocellier, P.

    1984-01-01

    Direct observation of resonant nuclear reactions, backscattering spectrometry and X ray microanalysis with a nuclear microprobe were used to determine elementary depth profiles in the near surface region of leached glasses. Some computing programs required to interpretate the analytical information detected were built. Experimental conditions to characterize glass samples without secondary effects were defined; and the influence of some leaching parameters was studied to describe the first stages of aqueous corrosion of borosilicate glasses [fr

  17. SU-E-T-422: Correlation Between 2D Passing Rates and 3D Dose Differences for Pretreatment VMAT QA

    International Nuclear Information System (INIS)

    Jin, X; Xie, C

    2014-01-01

    Purpose: Volumetric modulated arc therapy (VMAT) quality assurance (QA) is typically using QA methods and action levels taken from fixedbeam intensity-modulated radiotherapy (IMRT) QA methods. However, recent studies demonstrated that there is no correlation between the percent gamma passing rate (%GP) and the magnitude of dose discrepancy between the planned dose and the actual delivered dose for IMRT. The purpose of this study is to investigate whether %GP is correlated with clinical dosimetric difference for VMAT. Methods: Twenty nasopharyngeal cancer (NPC) patients treated with dual-arc simultaneous integrated boost VMAT and 20 esophageal cancer patients treated with one-arc VMAT were enrolled in this study. Pretreatment VMAT QA was performed by a 3D diode array ArcCheck. Acceptance criteria of 2%/2mm, 3%/3mm, and 4%/4mm were applied for 2D %GP. Dose values below 10% of the per-measured normalization maximum dose were ignored.Mean DVH values obtained from 3DVH software and TPS were calculated and percentage dose differences were calculated. Statistical correlation between %GP and percent dose difference was studied by using Pearson correlation. Results: The %GP for criteria 2%/2mm, 3%/3mm, and 4%/4mm were 82.33±4.45, 93.47±2.31, 97.13±2.41, respectively. Dose differences calculated from 3DVH and TPS for beam isocenter, mean dose of PTV, maximum dose of PTV, D2 of PTV and D98 of PTV were -1.04±3.24, -0.74±1.71, 2.92±3.62, 0.89±3.29, -1.46±1.97, respectively. No correction were found between %GP and dose differences. Conclusion: There are weak correlations between the 2D %GP and dose differences calculated from 3DVH. The %GP acceptance criteria of 3%/3mm usually applied for pretreatment QA of IMRT and VMAT is not indicating strong clinical correlation with 3D dose difference. 3D dose reconstructions on patient anatomy may be necessary for physicist to predict the accuracy of delivered dose for VMAT QA

  18. Modeling nexus of urban heat island mitigation strategies with electricity/power usage and consumer costs: a case study for Phoenix, Arizona, USA

    Science.gov (United States)

    Silva, Humberto; Fillpot, Baron S.

    2018-01-01

    A reduction in both power and electricity usage was determined using a previously validated zero-dimensional energy balance model that implements mitigation strategies used to reduce the urban heat island (UHI) effect. The established model has been applied to show the change in urban characteristic temperature when executing four common mitigation strategies: increasing the overall (1) emissivity, (2) vegetated area, (3) thermal conductivity, and (4) albedo of the urban environment in a series of increases by 5, 10, 15, and 20% from baseline values. Separately, a correlation analysis was performed involving meteorological data and total daily energy (TDE) consumption where the 24-h average temperature was shown to have the greatest correlation to electricity service data in the Phoenix, Arizona, USA, metropolitan region. A methodology was then developed for using the model to predict TDE consumption reduction and corresponding cost-saving analysis when implementing the four mitigation strategies. The four modeled UHI mitigation strategies, taken in combination, would lead to the largest percent reduction in annual energy usage, where increasing the thermal conductivity is the single most effective mitigation strategy. The single least effective mitigation strategy, increasing the emissivity by 5% from the baseline value, resulted in an average calculated reduction of about 1570 GWh in yearly energy usage with a corresponding 157 million dollar cost savings. When the four parameters were increased in unison by 20% from baseline values, an average calculated reduction of about 2050 GWh in yearly energy usage was predicted with a corresponding 205 million dollar cost savings.

  19. Parametric study of a turbocompound diesel engine based on an analytical model

    International Nuclear Information System (INIS)

    Zhao, Rongchao; Zhuge, Weilin; Zhang, Yangjun; Yin, Yong; Zhao, Yanting; Chen, Zhen

    2016-01-01

    Turbocompounding is an important technique to recover waste heat from engine exhaust and reduce CO_2 emission. This paper presents a parametric study of turbocompound diesel engine based on analytical model. An analytical model was developed to investigate the influence of system parameters on the engine fuel consumption. The model is based on thermodynamics knowledge and empirical models, which can consider the impacts of each parameter independently. The effects of turbine efficiency, back pressure, exhaust temperature, pressure ratio and engine speed on the recovery energy, pumping loss and engine fuel reductions were studied. Results show that turbine efficiency, exhaust temperature and back pressure has great influence on the fuel reduction and optimal power turbine (PT) expansion ratio. However, engine operation speed has little impact on the fuel savings obtained by turbocompounding. The interaction mechanism between the PT recovery power and engine pumping loss is presented in the paper. Due to the nonlinear characteristic of turbine power, there is an optimum value of PT expansion ratio to achieve largest power gain. At the end, the fuel saving potential of high performance turbocompound engine and the requirements for it are proposed in the paper. - Highlights: • An analytical model for turbocompound engine is developed and validated. • Parametric study is performed to obtain lowest BSFC and optimal expansion ratio. • The influences of each parameter on the fuel saving potentials are presented. • The impact mechanisms of each parameter on the energy tradeoff are disclosed. • It provides an effective tool to guide the preliminary design of turbocompounding.

  20. A novel approach to EPID-based 3D volumetric dosimetry for IMRT and VMAT QA

    Science.gov (United States)

    Alhazmi, Abdulaziz; Gianoli, Chiara; Neppl, Sebastian; Martins, Juliana; Veloza, Stella; Podesta, Mark; Verhaegen, Frank; Reiner, Michael; Belka, Claus; Parodi, Katia

    2018-06-01

    Intensity modulated radiation therapy (IMRT) and volumetric modulated arc therapy (VMAT) are relatively complex treatment delivery techniques and require quality assurance (QA) procedures. Pre-treatment dosimetric verification represents a fundamental QA procedure in daily clinical routine in radiation therapy. The purpose of this study is to develop an EPID-based approach to reconstruct a 3D dose distribution as imparted to a virtual cylindrical water phantom to be used for plan-specific pre-treatment dosimetric verification for IMRT and VMAT plans. For each depth, the planar 2D dose distributions acquired in air were back-projected and convolved by depth-specific scatter and attenuation kernels. The kernels were obtained by making use of scatter and attenuation models to iteratively estimate the parameters from a set of reference measurements. The derived parameters served as a look-up table for reconstruction of arbitrary measurements. The summation of the reconstructed 3D dose distributions resulted in the integrated 3D dose distribution of the treatment delivery. The accuracy of the proposed approach was validated in clinical IMRT and VMAT plans by means of gamma evaluation, comparing the reconstructed 3D dose distributions with Octavius measurement. The comparison was carried out using (3%, 3 mm) criteria scoring 99% and 96% passing rates for IMRT and VMAT, respectively. An accuracy comparable to the one of the commercial device for 3D volumetric dosimetry was demonstrated. In addition, five IMRT and five VMAT were validated against the 3D dose calculation performed by the TPS in a water phantom using the same passing rate criteria. The median passing rates within the ten treatment plans was 97.3%, whereas the lowest was 95%. Besides, the reconstructed 3D distribution is obtained without predictions relying on forward dose calculation and without external phantom or dosimetric devices. Thus, the approach provides a fully automated, fast and easy QA

  1. Analytical method of waste allocation in waste management systems: Concept, method and case study

    International Nuclear Information System (INIS)

    Bergeron, Francis C.

    2017-01-01

    Waste is not a rejected item to dispose anymore but increasingly a secondary resource to exploit, influencing waste allocation among treatment operations in a waste management (WM) system. The aim of this methodological paper is to present a new method for the assessment of the WM system, the “analytical method of the waste allocation process” (AMWAP), based on the concept of the “waste allocation process” defined as the aggregation of all processes of apportioning waste among alternative waste treatment operations inside or outside the spatial borders of a WM system. AMWAP contains a conceptual framework and an analytical approach. The conceptual framework includes, firstly, a descriptive model that focuses on the description and classification of the WM system. It includes, secondly, an explanatory model that serves to explain and to predict the operation of the WM system. The analytical approach consists of a step-by-step analysis for the empirical implementation of the conceptual framework. With its multiple purposes, AMWAP provides an innovative and objective modular method to analyse a WM system which may be integrated in the framework of impact assessment methods and environmental systems analysis tools. Its originality comes from the interdisciplinary analysis of the WAP and to develop the conceptual framework. AMWAP is applied in the framework of an illustrative case study on the household WM system of Geneva (Switzerland). It demonstrates that this method provides an in-depth and contextual knowledge of WM. - Highlights: • The study presents a new analytical method based on the waste allocation process. • The method provides an in-depth and contextual knowledge of the waste management system. • The paper provides a reproducible procedure for professionals, experts and academics. • It may be integrated into impact assessment or environmental system analysis tools. • An illustrative case study is provided based on household waste

  2. Analytical method of waste allocation in waste management systems: Concept, method and case study

    Energy Technology Data Exchange (ETDEWEB)

    Bergeron, Francis C., E-mail: francis.b.c@videotron.ca

    2017-01-15

    Waste is not a rejected item to dispose anymore but increasingly a secondary resource to exploit, influencing waste allocation among treatment operations in a waste management (WM) system. The aim of this methodological paper is to present a new method for the assessment of the WM system, the “analytical method of the waste allocation process” (AMWAP), based on the concept of the “waste allocation process” defined as the aggregation of all processes of apportioning waste among alternative waste treatment operations inside or outside the spatial borders of a WM system. AMWAP contains a conceptual framework and an analytical approach. The conceptual framework includes, firstly, a descriptive model that focuses on the description and classification of the WM system. It includes, secondly, an explanatory model that serves to explain and to predict the operation of the WM system. The analytical approach consists of a step-by-step analysis for the empirical implementation of the conceptual framework. With its multiple purposes, AMWAP provides an innovative and objective modular method to analyse a WM system which may be integrated in the framework of impact assessment methods and environmental systems analysis tools. Its originality comes from the interdisciplinary analysis of the WAP and to develop the conceptual framework. AMWAP is applied in the framework of an illustrative case study on the household WM system of Geneva (Switzerland). It demonstrates that this method provides an in-depth and contextual knowledge of WM. - Highlights: • The study presents a new analytical method based on the waste allocation process. • The method provides an in-depth and contextual knowledge of the waste management system. • The paper provides a reproducible procedure for professionals, experts and academics. • It may be integrated into impact assessment or environmental system analysis tools. • An illustrative case study is provided based on household waste

  3. Coccidiodomycosis in Arizona 2007-2008

    Centers for Disease Control (CDC) Podcasts

    This podcast looks at the impact of Coccidioidomycosis, or Valley Fever, in Arizona in 2007 and early 2008. CDC epidemiologist Dr. Tom Chiller discusses what researchers learned about this fungal disease.

  4. Upon the reconstruction of accidents triggered by tire explosion. Analytical model and case study

    Science.gov (United States)

    Gaiginschi, L.; Agape, I.; Talif, S.

    2017-10-01

    Accident Reconstruction is important in the general context of increasing road traffic safety. In the casuistry of traffic accidents, those caused by tire explosions are critical under the severity of consequences, because they are usually happening at high speeds. Consequently, the knowledge of the running speed of the vehicle involved at the time of the tire explosion is essential to elucidate the circumstances of the accident. The paper presents an analytical model for the kinematics of a vehicle which, after the explosion of one of its tires, begins to skid, overturns and rolls. The model consists of two concurent approaches built as applications of the momentum conservation and energy conservation principles, and allows determination of the initial speed of the vehicle involved, by running backwards the sequences of the road event. The authors also aimed to both validate the two distinct analytical approaches by calibrating the calculation algorithms on a case study

  5. Study of a vibrating plate: comparison between experimental (ESPI) and analytical results

    Science.gov (United States)

    Romero, G.; Alvarez, L.; Alanís, E.; Nallim, L.; Grossi, R.

    2003-07-01

    Real-time electronic speckle pattern interferometry (ESPI) was used for tuning and visualization of natural frequencies of a trapezoidal plate. The plate was excited to resonant vibration by a sinusoidal acoustical source, which provided a continuous range of audio frequencies. Fringe patterns produced during the time-average recording of the vibrating plate—corresponding to several resonant frequencies—were registered. From these interferograms, calculations of vibrational amplitudes by means of zero-order Bessel functions were performed in some particular cases. The system was also studied analytically. The analytical approach developed is based on the Rayleigh-Ritz method and on the use of non-orthogonal right triangular co-ordinates. The deflection of the plate is approximated by a set of beam characteristic orthogonal polynomials generated by using the Gram-Schmidt procedure. A high degree of correlation between computational analysis and experimental results was observed.

  6. Study on the Analytical Method for Determination of P-32 in Human Hair

    International Nuclear Information System (INIS)

    Syarbaini; Lubis, E.; Sarwani

    1996-01-01

    Neutron doses due to accident criticality can be estimated by measuring of radionuclide of neutron activation products in human hair. In this work, the analytical method for the determination of P-32 in neutron irradiated hair sample by G.A Siwabessy reactor has been studied. This analytical method consists of dissolving of human hair sample by 10 M HNO3, separation dan purification of P-32 by precipitation as ammonium molibdophosphate finally, the precipitate was measured by low backgroundα/βcounter. The minimum detectable activity of P-32 was 0,05 Bq at a background of 4,6 cpm and with a counting efficiency of 55 % for a 30 minute counting time

  7. Analytical study on holographic superfluid in AdS soliton background

    International Nuclear Information System (INIS)

    Lai, Chuyu; Pan, Qiyuan; Jing, Jiliang; Wang, Yongjiu

    2016-01-01

    We analytically study the holographic superfluid phase transition in the AdS soliton background by using the variational method for the Sturm–Liouville eigenvalue problem. By investigating the holographic s-wave and p-wave superfluid models in the probe limit, we observe that the spatial component of the gauge field will hinder the phase transition. Moreover, we note that, different from the AdS black hole spacetime, in the AdS soliton background the holographic superfluid phase transition always belongs to the second order and the critical exponent of the system takes the mean-field value in both s-wave and p-wave models. Our analytical results are found to be in good agreement with the numerical findings.

  8. Integrative Spatial Data Analytics for Public Health Studies of New York State.

    Science.gov (United States)

    Chen, Xin; Wang, Fusheng

    2016-01-01

    Increased accessibility of health data made available by the government provides unique opportunity for spatial analytics with much higher resolution to discover patterns of diseases, and their correlation with spatial impact indicators. This paper demonstrated our vision of integrative spatial analytics for public health by linking the New York Cancer Mapping Dataset with datasets containing potential spatial impact indicators. We performed spatial based discovery of disease patterns and variations across New York State, and identify potential correlations between diseases and demographic, socio-economic and environmental indicators. Our methods were validated by three correlation studies: the correlation between stomach cancer and Asian race, the correlation between breast cancer and high education population, and the correlation between lung cancer and air toxics. Our work will allow public health researchers, government officials or other practitioners to adequately identify, analyze, and monitor health problems at the community or neighborhood level for New York State.

  9. Analytical study on the self-healing property of Bessel beam

    Science.gov (United States)

    Chu, X.

    2012-10-01

    With the help of Babinet principle, an analytical expression for the self-healing of Bessel beam is derived by using the Gaussian absorption function to describe the obstacle. Based on the analytical expression, the self-healing properties of Bessel beam are studied. It shows that Bessel beam has the ability to reconstruct its beam shape disturbed by an obstacle. However, during the self-healing process, not only the intensity of the beam behind the obstacle but also the other part will be affected by the obstruction. Meanwhile, the highlight spot, which intensity is larger than that without the obstacle will appear, and the size and strength of the highlight spot is determined by the size of the obstacle. From the change of Poynting vector and Babinet principle, the physical interpretations for the self-healing ability, the effects of the obstruction on the other part and the appearance of highlight spot are given.

  10. International conference on nuclear analytical methods in the life sciences (NAMLS) (abstracts)

    International Nuclear Information System (INIS)

    1999-01-01

    The International Conference on Nuclear Analytical Methods in the Life Sciences (NAMLS) was hold on October 26-30, 1998 in Beijing, China, which was organized by China Institute of Atomic Energy in Cooperation with IAEA, National Science Foundation of China, China National Nuclear Cooperation, Chinese Academy of Sciences, Institute of High Energy Physics, Shanghai Institute for Nuclear Research, Chinese Nuclear Society, Nuclear Physics Society of China and Nuclear Chemistry Society of China. the contents of this Conference include: 1. QA-QC and CRM studies; 2. Elemental speciation and localization; 3. Health-related environmental studies; 4. Recent development in nuclear and related analytical techniques; 5. Trace elements in health and diseases; 6. Miscellaneous applications of NAT in the life sciences

  11. Site study plan for geochemical analytical requirements and methodologies: Revision 1

    International Nuclear Information System (INIS)

    1987-12-01

    This site study plan documents the analytical methodologies and procedures that will be used to analyze geochemically the rock and fluid samples collected during Site Characterization. Information relating to the quality aspects of these analyses is also provided, where available. Most of the proposed analytical procedures have been used previously on the program and are sufficiently sensitive to yield high-quality analyses. In a few cases improvements in analytical methodology (e.g., greater sensitivity, fewer interferences) are desired. Suggested improvements to these methodologies are discussed. In most cases these method-development activities have already been initiated. The primary source of rock and fluid samples for geochemical analysis during Site Characterization will be the drilling program, as described in various SRP Site Study Plans. The Salt Repository Project (SRP) Networks specify the schedule under which the program will operate. Drilling will not begin until after site ground water baseline conditions have been established. The Technical Field Services Contractor (TFSC) is responsible for conducting the field program of drilling and testing. Samples and data will be handled and reported in accordance with established SRP procedures. A quality assurance program will be utilized to assure that activities affecting quality are performed correctly and that the appropriate documentation is maintained. 28 refs., 9 figs., 14 tabs

  12. An analytic study of applying Miller cycle to reduce NOx emission from petrol engine

    International Nuclear Information System (INIS)

    Wang Yaodong; Lin Lin; Roskilly, Anthony P.; Zeng Shengchuo; Huang, Jincheng; He Yunxin; Huang Xiaodong; Huang Huilan; Wei Haiyan; Li Shangping; Yang Jing

    2007-01-01

    An analytic investigation of applying Miller cycle to reduce nitrogen oxides (NO x ) emissions from a petrol engine is carried out. The Miller cycle used in the investigation is a late intake valve closing version. A detailed thermodynamic analysis of the cycle is presented. A comparison of the characters of Miller cycle with Otto cycle is presented. From the results of thermodynamic analyses, it can be seen that the application of Miller cycle is able to reduce the compression pressure and temperature in the cylinder at the end of compression stroke. Therefore, it lowers down the combustion temperature and NO x formation in engine cylinder. These results in a lower exhaust temperature and less NO x emissions compared with that of Otto cycle. The analytic results also show that Miller cycle ratio is a main factor to influence the combustion temperature, and then the NO x emissions and the exhaust temperature. The results from the analytic study are used to analyse and to compare with the previous experimental results. An empirical formula from the previous experimental results that showed the relation of NO x emissions with the exhaust temperature at different engine speed is presented. The results from the study showed that the application of Miller cycle may reduce NO x emissions from petrol engine

  13. A semi-analytical study of positive corona discharge in wire–plane electrode configuration

    International Nuclear Information System (INIS)

    Yanallah, K; Pontiga, F; Chen, J H

    2013-01-01

    Wire-to-plane positive corona discharge in air has been studied using an analytical model of two species (electrons and positive ions). The spatial distributions of electric field and charged species are obtained by integrating Gauss's law and the continuity equations of species along the Laplacian field lines. The experimental values of corona current intensity and applied voltage, together with Warburg's law, have been used to formulate the boundary condition for the electron density on the corona wire. To test the accuracy of the model, the approximate electric field distribution has been compared with the exact numerical solution obtained from a finite element analysis. A parametrical study of wire-to-plane corona discharge has then been undertaken using the approximate semi-analytical solutions. Thus, the spatial distributions of electric field and charged particles have been computed for different values of the gas pressure, wire radius and electrode separation. Also, the two dimensional distribution of ozone density has been obtained using a simplified plasma chemistry model. The approximate semi-analytical solutions can be evaluated in a negligible computational time, yet provide precise estimates of corona discharge variables. (paper)

  14. A semi-analytical study of positive corona discharge in wire-plane electrode configuration

    Science.gov (United States)

    Yanallah, K.; Pontiga, F.; Chen, J. H.

    2013-08-01

    Wire-to-plane positive corona discharge in air has been studied using an analytical model of two species (electrons and positive ions). The spatial distributions of electric field and charged species are obtained by integrating Gauss's law and the continuity equations of species along the Laplacian field lines. The experimental values of corona current intensity and applied voltage, together with Warburg's law, have been used to formulate the boundary condition for the electron density on the corona wire. To test the accuracy of the model, the approximate electric field distribution has been compared with the exact numerical solution obtained from a finite element analysis. A parametrical study of wire-to-plane corona discharge has then been undertaken using the approximate semi-analytical solutions. Thus, the spatial distributions of electric field and charged particles have been computed for different values of the gas pressure, wire radius and electrode separation. Also, the two dimensional distribution of ozone density has been obtained using a simplified plasma chemistry model. The approximate semi-analytical solutions can be evaluated in a negligible computational time, yet provide precise estimates of corona discharge variables.

  15. A modified analytical model to study the sensing performance of a flexible capacitive tactile sensor array

    International Nuclear Information System (INIS)

    Liang, Guanhao; Wang, Yancheng; Mei, Deqing; Xi, Kailun; Chen, Zichen

    2015-01-01

    This paper presents a modified analytical model to study the sensing performance of a flexible capacitive tactile sensor array, which utilizes solid polydimethylsiloxane (PDMS) film as the dielectric layer. To predict the deformation of the sensing unit and capacitance changes, each sensing unit is simplified into a three-layer plate structure and divided into central, edge and corner regions. The plate structure and the three regions are studied by the general and modified models, respectively. For experimental validation, the capacitive tactile sensor array with 8  ×  8 (= 64) sensing units is fabricated. Experiments are conducted by measuring the capacitance changes versus applied external forces and compared with the general and modified models’ predictions. For the developed tactile sensor array, the sensitivity predicted by the modified analytical model is 1.25%/N, only 0.8% discrepancy from the experimental measurement. Results demonstrate that the modified analytical model can accurately predict the sensing performance of the sensor array and could be utilized for model-based optimal capacitive tactile sensor array design. (paper)

  16. A multicenter nationwide reference intervals study for common biochemical analytes in Turkey using Abbott analyzers.

    Science.gov (United States)

    Ozarda, Yesim; Ichihara, Kiyoshi; Aslan, Diler; Aybek, Hulya; Ari, Zeki; Taneli, Fatma; Coker, Canan; Akan, Pinar; Sisman, Ali Riza; Bahceci, Onur; Sezgin, Nurzen; Demir, Meltem; Yucel, Gultekin; Akbas, Halide; Ozdem, Sebahat; Polat, Gurbuz; Erbagci, Ayse Binnur; Orkmez, Mustafa; Mete, Nuriye; Evliyaoglu, Osman; Kiyici, Aysel; Vatansev, Husamettin; Ozturk, Bahadir; Yucel, Dogan; Kayaalp, Damla; Dogan, Kubra; Pinar, Asli; Gurbilek, Mehmet; Cetinkaya, Cigdem Damla; Akin, Okhan; Serdar, Muhittin; Kurt, Ismail; Erdinc, Selda; Kadicesme, Ozgur; Ilhan, Necip; Atali, Dilek Sadak; Bakan, Ebubekir; Polat, Harun; Noyan, Tevfik; Can, Murat; Bedir, Abdulkerim; Okuyucu, Ali; Deger, Orhan; Agac, Suret; Ademoglu, Evin; Kaya, Ayşem; Nogay, Turkan; Eren, Nezaket; Dirican, Melahat; Tuncer, GulOzlem; Aykus, Mehmet; Gunes, Yeliz; Ozmen, Sevda Unalli; Kawano, Reo; Tezcan, Sehavet; Demirpence, Ozlem; Degirmen, Elif

    2014-12-01

    A nationwide multicenter study was organized to establish reference intervals (RIs) in the Turkish population for 25 commonly tested biochemical analytes and to explore sources of variation in reference values, including regionality. Blood samples were collected nationwide in 28 laboratories from the seven regions (≥400 samples/region, 3066 in all). The sera were collectively analyzed in Uludag University in Bursa using Abbott reagents and analyzer. Reference materials were used for standardization of test results. After secondary exclusion using the latent abnormal values exclusion method, RIs were derived by a parametric method employing the modified Box-Cox formula and compared with the RIs by the non-parametric method. Three-level nested ANOVA was used to evaluate variations among sexes, ages and regions. Associations between test results and age, body mass index (BMI) and region were determined by multiple regression analysis (MRA). By ANOVA, differences of reference values among seven regions were significant in none of the 25 analytes. Significant sex-related and age-related differences were observed for 10 and seven analytes, respectively. MRA revealed BMI-related changes in results for uric acid, glucose, triglycerides, high-density lipoprotein (HDL)-cholesterol, alanine aminotransferase, and γ-glutamyltransferase. Their RIs were thus derived by applying stricter criteria excluding individuals with BMI >28 kg/m2. Ranges of RIs by non-parametric method were wider than those by parametric method especially for those analytes affected by BMI. With the lack of regional differences and the well-standardized status of test results, the RIs derived from this nationwide study can be used for the entire Turkish population.

  17. Analytical mechanics

    CERN Document Server

    Lemos, Nivaldo A

    2018-01-01

    Analytical mechanics is the foundation of many areas of theoretical physics including quantum theory and statistical mechanics, and has wide-ranging applications in engineering and celestial mechanics. This introduction to the basic principles and methods of analytical mechanics covers Lagrangian and Hamiltonian dynamics, rigid bodies, small oscillations, canonical transformations and Hamilton–Jacobi theory. This fully up-to-date textbook includes detailed mathematical appendices and addresses a number of advanced topics, some of them of a geometric or topological character. These include Bertrand's theorem, proof that action is least, spontaneous symmetry breakdown, constrained Hamiltonian systems, non-integrability criteria, KAM theory, classical field theory, Lyapunov functions, geometric phases and Poisson manifolds. Providing worked examples, end-of-chapter problems, and discussion of ongoing research in the field, it is suitable for advanced undergraduate students and graduate students studying analyt...

  18. Phonon dispersion on Ag (100) surface: A modified analytic embedded atom method study

    International Nuclear Information System (INIS)

    Zhang Xiao-Jun; Chen Chang-Le

    2016-01-01

    Within the harmonic approximation, the analytic expression of the dynamical matrix is derived based on the modified analytic embedded atom method (MAEAM) and the dynamics theory of surface lattice. The surface phonon dispersions along three major symmetry directions, and XM-bar are calculated for the clean Ag (100) surface by using our derived formulas. We then discuss the polarization and localization of surface modes at points X-bar and M-bar by plotting the squared polarization vectors as a function of the layer index. The phonon frequencies of the surface modes calculated by MAEAM are compared with the available experimental and other theoretical data. It is found that the present results are generally in agreement with the referenced experimental or theoretical results, with a maximum deviation of 10.4%. The agreement shows that the modified analytic embedded atom method is a reasonable many-body potential model to quickly describe the surface lattice vibration. It also lays a significant foundation for studying the surface lattice vibration in other metals. (paper)

  19. Studies on analytical method and nondestructive measuring method on the sensitization of austenitic stainless steels

    International Nuclear Information System (INIS)

    Onimura, Kichiro; Arioka, Koji; Horai, Manabu; Noguchi, Shigeru.

    1982-03-01

    Austenitic stainless steels are widely used as structural materials for the machine and equipment of various kinds of plants, such as thermal power, nuclear power, and chemical plants. The machines and equipment using this kind of material, however, have the possibility of suffering corrosion damage while in service, and these damages are considered to be largely due to the sensitization of the material in sometimes. So, it is necessary to develop an analytical method for grasping the sensitization of the material more in detail and a quantitative nondestructive measuring method which is applicable to various kinds of structures in order to prevent the corrosion damage. From the above viewpoint, studies have been made on the analytical method based on the theory of diffusion of chromium in austenitic stainless steels and on Electro-Potentiokinetics Reactivation Method (EPR Method) as a nondestructive measuring method, using 304 and 316 austenitic stainless steels having different carbon contents in base metals. This paper introduces the results of EPR test on the sensitization of austenitic stainless steels and the correlation between analytical and experimental results. (author)

  20. Analytical Modeling Approach to Study Harmonic Mitigation in AC Grids with Active Impedance at Selective Frequencies

    Directory of Open Access Journals (Sweden)

    Gonzalo Abad

    2018-05-01

    Full Text Available This paper presents an analytical model, oriented to study harmonic mitigation aspects in AC grids. As it is well known, the presence of non-desired harmonics in AC grids can be palliated in several manners. However, in this paper, a power electronic-based active impedance at selective frequencies (ACISEF is used, due to its already proven flexibility and adaptability to the changing characteristics of AC grids. Hence, the proposed analytical model approach is specially conceived to globally consider both the model of the AC grid itself with its electric equivalent impedances, together with the power electronic-based ACISEF, including its control loops. In addition, the proposed analytical model presents practical and useful properties, as it is simple to understand and simple to use, it has low computational cost and simple adaptability to different scenarios of AC grids, and it provides an accurate enough representation of the reality. The benefits of using the proposed analytical model are shown in this paper through some examples of its usefulness, including an analysis of stability and the identification of sources of instability for a robust design, an analysis of effectiveness in harmonic mitigation, an analysis to assist in the choice of the most suitable active impedance under a given state of the AC grid, an analysis of the interaction between different compensators, and so on. To conclude, experimental validation of a 2.15 kA ACISEF in a real 33 kV AC grid is provided, in which real users (household and industry loads and crucial elements such as wind parks and HVDC systems are near inter-connected.

  1. Seamless Digital Environment – Plan for Data Analytics Use Case Study

    Energy Technology Data Exchange (ETDEWEB)

    Oxstrand, Johanna Helene [Idaho National Lab. (INL), Idaho Falls, ID (United States); Bly, Aaron Douglas [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2016-09-01

    The U.S Department of Energy Light Water Reactor Sustainability (LWRS) Program initiated research in to what is needed in order to provide a roadmap or model for Nuclear Power Plants to reference when building an architecture that can support the growing data supply and demand flowing through their networks. The Digital Architecture project published report Digital Architecture Planning Model (Oxstrand et. al, 2016) discusses things to consider when building an architecture to support the increasing needs and demands of data throughout the plant. Once the plant is able to support the data demands it still needs to be able to provide the data in an easy, quick and reliable method. A common method is to create a “one stop shop” application that a user can go to get all the data they need. The creation of this leads to the need of creating a Seamless Digital Environment (SDE) to integrate all the “siloed” data. An SDE is the desired perception that should be presented to users by gathering the data from any data source (e.g., legacy applications and work management systems) without effort by the user. The goal for FY16 was to complete a feasibility study for data mining and analytics for employing information from computer-based procedures enabled technologies for use in developing improved business analytics. The research team collaborated with multiple organizations to identify use cases or scenarios, which could be beneficial to investigate in a feasibility study. Many interesting potential use cases were identified throughout the FY16 activity. Unfortunately, due to factors out of the research team’s control, none of the studies were initiated this year. However, the insights gained and the relationships built with both PVNGS and NextAxiom will be valuable when moving forward with future research. During the 2016 annual Nuclear Information Technology Strategic Leadership (NITSL) group meeting it was identified would be very beneficial to the industry to

  2. Publication bias in studies of an applied behavior-analytic intervention: an initial analysis.

    Science.gov (United States)

    Sham, Elyssa; Smith, Tristram

    2014-01-01

    Publication bias arises when studies with favorable results are more likely to be reported than are studies with null findings. If this bias occurs in studies with single-subject experimental designs(SSEDs) on applied behavior-analytic (ABA) interventions, it could lead to exaggerated estimates of intervention effects. Therefore, we conducted an initial test of bias by comparing effect sizes, measured by percentage of nonoverlapping data (PND), in published SSED studies (n=21) and unpublished dissertations (n=10) on 1 well-established intervention for children with autism, pivotal response treatment (PRT). Although published and unpublished studies had similar methodologies, the mean PND in published studies was 22% higher than in unpublished studies, 95% confidence interval (4%, 38%). Even when unpublished studies are included, PRT appeared to be effective (PNDM=62%). Nevertheless, the disparity between published and unpublished studies suggests a need for further assessment of publication bias in the ABA literature.

  3. Coevolution of nonlinear trends in vegetation, soils, and topography with elevation and slope aspect: A case study in the sky islands of southern Arizona

    Science.gov (United States)

    Pelletier, Jon D.; Barron-Gafford, Greg A.; Breshears, David D.; Brooks, Paul D.; Chorover, Jon; Durcik, Matej; Harman, Ciaran J.; Huxman, Travis E.; Lohse, Kathleen A.; Lybrand, Rebecca; Meixner, Tom; McIntosh, Jennifer C.; Papuga, Shirley A.; Rasmussen, Craig; Schaap, Marcel; Swetnam, Tyson L.; Troch, Peter A.

    2013-06-01

    among vegetation dynamics, pedogenesis, and topographic development affect the "critical zone"—the living filter for Earth's hydrologic, biogeochemical, and rock/sediment cycles. Assessing the importance of such feedbacks, which may be particularly pronounced in water-limited systems, remains a fundamental interdisciplinary challenge. The sky islands of southern Arizona offer an unusually well-defined natural experiment involving such feedbacks because mean annual precipitation varies by a factor of five over distances of approximately 10 km in areas of similar rock type (granite) and tectonic history. Here we compile high-resolution, spatially distributed data for Effective Energy and Mass Transfer (EEMT: the energy available to drive bedrock weathering), above-ground biomass, soil thickness, hillslope-scale topographic relief, and drainage density in two such mountain ranges (Santa Catalina: SCM; Pinaleño: PM). Strong correlations exist among vegetation-soil-topography variables, which vary nonlinearly with elevation, such that warm, dry, low-elevation portions of these ranges are characterized by relatively low above-ground biomass, thin soils, minimal soil organic matter, steep slopes, and high drainage densities; conversely, cooler, wetter, higher elevations have systematically higher biomass, thicker organic-rich soils, gentler slopes, and lower drainage densities. To test if eco-pedo-geomorphic feedbacks drive this pattern, we developed a landscape evolution model that couples pedogenesis and topographic development over geologic time scales, with rates explicitly dependent on vegetation density. The model self-organizes into states similar to those observed in SCM and PM. Our results highlight the potential importance of eco-pedo-geomorphic feedbacks, mediated by soil thickness, in water-limited systems.

  4. Individual and Collective Responses to Crisis: An Analytical Framework for the Study of Social Resilience

    Directory of Open Access Journals (Sweden)

    Juan Díez Medrano

    2014-11-01

    Full Text Available This article proposes a sociological approach for the study of social resilience that emphasizes interpretation and the role of networks. After discussing past contributions to the study of social resilience and proposing an alternative analytical framework that builds on Max Weber’s approach to social action, the article illustrates the proposed strategy through a discussion of the acquisition of transnational skills as a strategy of social resilience. Available empirical evidence shows indeed that fluency in foreign languages works both a resilience strategy and a vehicle toward the emergence of an European demos

  5. 76 FR 28079 - Notice of Intent To Repatriate Cultural Items: Arizona State Museum, University of Arizona...

    Science.gov (United States)

    2011-05-13

    ... Arizona State Museum, University of Arizona, Tucson, AZ, that meet the definitions of unassociated... 4 eagle feathers, 1 stone purifying bowl, 3 medicine man's baskets, 1 medicine basket lid, 4 medicine man's basket fragments, 1 animal bone, 2 carved animal effigies, 1 carved human effigy, 1 feather...

  6. COMPARISONS OF PESTICIDE LEVELS AND EXPOSURES IN NHEXAS ARIZONA AND ARIZONA-MEXICO BORDER POPULATIONS

    Science.gov (United States)

    The distributions of organophosphate (OP) insecticides chlorpyrifos and diazinon in exposure matrices such as indoor air, house dust, food, and water have been determined for 416 homes in the general Arizona population, and for 87 homes along the Arizona-Mexico border. The con...

  7. Learners' and Teachers' Perceptions of Learning Analytics (LA): A Case Study of Southampton Solent University (SSU)

    Science.gov (United States)

    Khan, Osama

    2017-01-01

    This paper depicts a perceptual picture of learning analytics based on the understanding of learners and teachers at the SSU as a case study. The existing literature covers technical challenges of learning analytics (LA) and how it creates better social construct for enhanced learning support, however, there has not been adequate research on…

  8. Clinical validation of an in-house EPID dosimetry system for IMRT QA at the Prince of Wales Hospital

    Science.gov (United States)

    Tyler, M.; Vial, P.; Metcalfe, P.; Downes, S.

    2013-06-01

    In this study a simple method using standard flood-field corrected Electronic Portal Imaging Device (EPID) images for routine Intensity Modulated Radiation Therapy (IMRT) Quality Assurance (QA) was investigated. The EPID QA system was designed and tested on a Siemens Oncor Impression linear accelerator with an OptiVue 1000ST EPID panel (Siemens Medical Solutions USA, Inc, USA) and an Elekta Axesse linear accelerator with an iViewGT EPID (Elekta AB, Sweden) for 6 and 10 MV IMRT fields with Step-and-Shoot and dynamic-MLC delivery. Two different planning systems were used for patient IMRT field generation for comparison with the measured EPID fluences. All measured IMRT plans had >95% agreement to the planning fluences (using 3 cGy / 3 mm Gamma Criteria) and were comparable to the pass-rates calculated using a 2-D diode array dosimeter.

  9. Clinical validation of an in-house EPID dosimetry system for IMRT QA at the Prince of Wales Hospital

    International Nuclear Information System (INIS)

    Tyler, M; Downes, S; Vial, P; Metcalfe, P

    2013-01-01

    In this study a simple method using standard flood-field corrected Electronic Portal Imaging Device (EPID) images for routine Intensity Modulated Radiation Therapy (IMRT) Quality Assurance (QA) was investigated. The EPID QA system was designed and tested on a Siemens Oncor Impression linear accelerator with an OptiVue 1000ST EPID panel (Siemens Medical Solutions USA, Inc, USA) and an Elekta Axesse linear accelerator with an iViewGT EPID (Elekta AB, Sweden) for 6 and 10 MV IMRT fields with Step-and-Shoot and dynamic-MLC delivery. Two different planning systems were used for patient IMRT field generation for comparison with the measured EPID fluences. All measured IMRT plans had >95% agreement to the planning fluences (using 3 cGy / 3 mm Gamma Criteria) and were comparable to the pass-rates calculated using a 2-D diode array dosimeter.

  10. Analytical methods applied to the study of lattice gauge and spin theories

    International Nuclear Information System (INIS)

    Moreo, Adriana.

    1985-01-01

    A study of interactions between quarks and gluons is presented. Certain difficulties of the quantum chromodynamics to explain the behaviour of quarks has given origin to the technique of lattice gauge theories. First the phase diagrams of the discrete space-time theories are studied. The analysis of the phase diagrams is made by numerical and analytical methods. The following items were investigated and studied: a) A variational technique was proposed to obtain very accurated values for the ground and first excited state energy of the analyzed theory; b) A mean-field-like approximation for lattice spin models in the link formulation which is a generalization of the mean-plaquette technique was developed; c) A new method to study lattice gauge theories at finite temperature was proposed. For the first time, a non-abelian model was studied with analytical methods; d) An abelian lattice gauge theory with fermionic matter at the strong coupling limit was analyzed. Interesting results applicable to non-abelian gauge theories were obtained. (M.E.L.) [es

  11. Big data analytics for the Future Circular Collider reliability and availability studies

    Science.gov (United States)

    Begy, Volodimir; Apollonio, Andrea; Gutleber, Johannes; Martin-Marquez, Manuel; Niemi, Arto; Penttinen, Jussi-Pekka; Rogova, Elena; Romero-Marin, Antonio; Sollander, Peter

    2017-10-01

    Responding to the European Strategy for Particle Physics update 2013, the Future Circular Collider study explores scenarios of circular frontier colliders for the post-LHC era. One branch of the study assesses industrial approaches to model and simulate the reliability and availability of the entire particle collider complex based on the continuous monitoring of CERN’s accelerator complex operation. The modelling is based on an in-depth study of the CERN injector chain and LHC, and is carried out as a cooperative effort with the HL-LHC project. The work so far has revealed that a major challenge is obtaining accelerator monitoring and operational data with sufficient quality, to automate the data quality annotation and calculation of reliability distribution functions for systems, subsystems and components where needed. A flexible data management and analytics environment that permits integrating the heterogeneous data sources, the domain-specific data quality management algorithms and the reliability modelling and simulation suite is a key enabler to complete this accelerator operation study. This paper describes the Big Data infrastructure and analytics ecosystem that has been put in operation at CERN, serving as the foundation on which reliability and availability analysis and simulations can be built. This contribution focuses on data infrastructure and data management aspects and presents case studies chosen for its validation.

  12. Application of X-ray fluorescence analytical techniques in phytoremediation and plant biology studies

    International Nuclear Information System (INIS)

    Necemer, Marijan; Kump, Peter; Scancar, Janez; Jacimovic, Radojko; Simcic, Jurij; Pelicon, Primoz; Budnar, Milos; Jeran, Zvonka; Pongrac, Paula; Regvar, Marjana; Vogel-Mikus, Katarina

    2008-01-01

    Phytoremediation is an emerging technology that employs the use of higher plants for the clean-up of contaminated environments. Progress in the field is however handicapped by limited knowledge of the biological processes involved in plant metal uptake, translocation, tolerance and plant-microbe-soil interactions; therefore a better understanding of the basic biological mechanisms involved in plant/microbe/soil/contaminant interactions would allow further optimization of phytoremediation technologies. In view of the needs of global environmental protection, it is important that in phytoremediation and plant biology studies the analytical procedures for elemental determination in plant tissues and soil should be fast and cheap, with simple sample preparation, and of adequate accuracy and reproducibility. The aim of this study was therefore to present the main characteristics, sample preparation protocols and applications of X-ray fluorescence-based analytical techniques (energy dispersive X-ray fluorescence spectrometry-EDXRF, total reflection X-ray fluorescence spectrometry-TXRF and micro-proton induced X-ray emission-micro-PIXE). Element concentrations in plant leaves from metal polluted and non-polluted sites, as well as standard reference materials, were analyzed by the mentioned techniques, and additionally by instrumental neutron activation analysis (INAA) and atomic absorption spectrometry (AAS). The results were compared and critically evaluated in order to assess the performance and capability of X-ray fluorescence-based techniques in phytoremediation and plant biology studies. It is the EDXRF, which is recommended as suitable to be used in the analyses of a large number of samples, because it is multi-elemental, requires only simple preparation of sample material, and it is analytically comparable to the most frequently used instrumental chemical techniques. The TXRF is compatible to FAAS in sample preparation, but relative to AAS it is fast, sensitive and

  13. Studies on the spectral interference of gadolinium on different analytes in inductively coupled plasma atomic emission spectroscopy

    International Nuclear Information System (INIS)

    Sengupta, Arijit; Thulasidas, S.K.; Natarajan, V.; Airan, Yougant

    2015-01-01

    Due to the multi-electronic nature, rare earth elements are prone to exhibit spectral interference in ICP-AES, which leads to erroneous determination of analytes in presence of such matrix. This interference is very significant, when the analytes are to be determined at trace level in presence of emission rich matrix elements. An attempt was made to understand the spectral interference of Gd on 29 common analytes like Ag, Al, B, Ba, Bi, Ca, Cd, Ce, Co, Cr, Cu, Dy, Fe, Ga, Gd, In, La, Li, Lu, Mg, Mn, Na, Nd, Ni, Pb, Pr, Sr, Tl and Zn using ICP-AES with capacitive Charged Coupled Device (CCD) as detector. The present study includes identification of suitable interference free analytical lines of these analytes, evaluation of correction factor for each analytical line and determination of tolerance levels of these analytical lines along with the ICP-AES based methodology for simultaneous determination of Gd. Based on the spectral interference study, an ICP-AES based method was developed for the determination of these analytes at trace level in presence of Gd matrix without chemical separation. Further the developed methodology was validated using synthetic samples prepared from commercially available reference material solution of individual element; the results were found to be satisfactory. The method was also compared with other existing techniques

  14. NRC [Nuclear Regulatory Commission] perspective of software QA [quality assurance] in the nuclear history

    International Nuclear Information System (INIS)

    Weiss, S.H.

    1988-01-01

    Computer technology has been a part of the nuclear industry since its inception. However, it is only recently that computers have been integrated into reactor operations. During the early history of commercial nuclear power in the United States, the US Nuclear Regulatory Commission (NRC) discouraged the use of digital computers for real-time control and monitoring of nuclear power plant operation. At the time, this position was justified since software engineering was in its infancy, and horror stories on computer crashes were plentiful. Since the advent of microprocessors and inexpensive computer memories, significant advances have been made in fault-tolerant computer architecture that have resulted in highly reliable, durable computer systems. The NRC's requirement for safety parameter display system (SPDS) stemmed form the results of studies and investigations conducted on the Three Mile Island Unit 2 (TMI-2) accident. An NRC contractor has prepared a handbook of software QA techniques applicable to the nuclear industry, published as NUREG/CR-4640 in August 1987. Currently, the NRC is considering development of an inspection program covering software QA. Future efforts may address verification and validation as applied to expert systems and artificial intelligence programs

  15. A finite-buffer queue with a single vacation policy: An analytical study with evolutionary positioning

    Directory of Open Access Journals (Sweden)

    Woźniak Marcin

    2014-12-01

    Full Text Available In this paper, application of an evolutionary strategy to positioning a GI/M/1/N-type finite-buffer queueing system with exhaustive service and a single vacation policy is presented. The examined object is modeled by a conditional joint transform of the first busy period, the first idle time and the number of packets completely served during the first busy period. A mathematical model is defined recursively by means of input distributions. In the paper, an analytical study and numerical experiments are presented. A cost optimization problem is solved using an evolutionary strategy for a class of queueing systems described by exponential and Erlang distributions.

  16. A functional-analytic method for the study of difference equations

    Directory of Open Access Journals (Sweden)

    Panayiotis D. Siafarikas

    2004-07-01

    Full Text Available We will give the generalization of a recently developed functional-analytic method for studying linear and nonlinear, ordinary and partial, difference equations in the ℓp1 and ℓp2 spaces, p∈ℕ, p≥1. The method will be illustrated by use of two examples concerning a nonlinear ordinary difference equation known as the Putnam equation, and a linear partial difference equation of three variables describing the discrete Newton law of cooling in three dimensions.

  17. Analytical and experimental study of two delay-coupled excitable units.

    Science.gov (United States)

    Weicker, Lionel; Erneux, Thomas; Keuninckx, Lars; Danckaert, Jan

    2014-01-01

    We investigate the onset of time-periodic oscillations for a system of two identical delay-coupled excitable (nonoscillatory) units. We first analyze these solutions by using asymptotic methods. The oscillations are described as relaxation oscillations exhibiting successive slow and fast changes. The analysis highlights the determinant role of the delay during the fast transition layers. We then study experimentally a system of two coupled electronic circuits that is modeled mathematically by the same delay differential equations. We obtain quantitative agreements between analytical and experimental bifurcation diagrams.

  18. Partial conservation of seniority in the j=9/2 shell: Analytic and numerical studies

    International Nuclear Information System (INIS)

    Qi Chong

    2011-01-01

    Recent studies show that for systems with four identical fermions in the j=9/2 shell, two special states, which have seniority v=4 and total spins I=4 and 6, are eigenstates of any two-body interaction. These states have good seniority for an arbitrary interaction. In this work, an analytic proof is given to this peculiar occurrence of partial conservation of seniority, which is the consequence of the special property of certain coefficients of fractional parentage. Further calculations did not reveal its existence in systems with other n and/or I for shells with j≤15/2.

  19. Analytical study of the conjecture rule for the combination of multipole effects in LHC

    CERN Document Server

    Guignard, Gilbert

    1997-01-01

    This paper summarizes the analytical investigation done on the conjecture law found by tracking for the effect on the dynamic aperture of the combination of two multipoles of various order. A one-dimensional model leading to an integrable system has been used to find closed formulae for the dynamic aperture associated with a fully distributed multipole. The combination has then been studied and the resulting expression compared with the assumed conjecture law. For integrated multipoles small with respect to the focusing strength, the conjecture appears to hold, though with an exponent different from the one expected by crude reasoning.

  20. Developing a business analytics methodology: a case study in the foodbank sector

    OpenAIRE

    Hindle, Giles; Vidgen, Richard

    2017-01-01

    The current research seeks to address the following question: how can organizations align their business analytics development projects with their business goals? To pursue this research agenda we adopt an action research framework to develop and apply a business analytics methodology (BAM). The four-stage BAM (problem situation structuring, business model mapping, analytics leverage analysis, and analytics implementation) is not a prescription. Rather, it provides a logical structure and log...

  1. Seismic vulnerability of the Himalayan half-dressed rubble stone masonry structures, experimental and analytical studies

    Directory of Open Access Journals (Sweden)

    N. Ahmad

    2012-11-01

    Full Text Available Half-Dressed rubble stone (DS masonry structures as found in the Himalayan region are investigated using experimental and analytical studies. The experimental study included a shake table test on a one-third scaled structural model, a representative of DS masonry structure employed for public critical facilities, e.g. school buildings, offices, health care units, etc. The aim of the experimental study was to understand the damage mechanism of the model, develop damage scale towards deformation-based assessment and retrieve the lateral force-deformation response of the model besides its elastic dynamic properties, i.e. fundamental vibration period and elastic damping. The analytical study included fragility analysis of building prototypes using a fully probabilistic nonlinear dynamic method. The prototypes are designed as SDOF systems assigned with lateral, force-deformation constitutive law (obtained experimentally. Uncertainties in the constitutive law, i.e. lateral stiffness, strength and deformation limits, are considered through random Monte Carlo simulation. Fifty prototype buildings are analyzed using a suite of ten natural accelerograms and an incremental dynamic analysis technique. Fragility and vulnerability functions are derived for the damageability assessment of structures, economic loss and casualty estimation during an earthquake given the ground shaking intensity, essential within the context of risk assessment of existing stock aiming towards risk mitigation and disaster risk reduction.

  2. Experimental and analytical studies on soil-structure interaction behavior of nuclear reactor building

    International Nuclear Information System (INIS)

    Tsushima, Y.

    1978-01-01

    The purpose of this study is to estimate damping effects due to soil-structure interaction by the dissipation of vibrational energy to the ground through the foundation in a building with a short fundamental period such as a nuclear reactor building. The author performed experimental and analytical studies on the vibrational characteristics of model steel structures ranging from one to four stories high erected on the rigid base and located on soil, which are simulated from the vibrational characteristics of a prototype reactor building: the former study is to obtain damping effects due to inner friction of steel frames and the latter to obtain radiation damping effects due to soil-structure interaction. The author also touches upon the results of experiments performed on a BWR-type reactor building in 1974, which showed damping ratios higher than 20% of those in fundamental modes. Then the author attempts to estimate the damping effects of the reactor building by his own method proposed in the report. Through these studies the author finally concludes that the experimental damping effects are remarkable in the lower modes by the energy dissipation and the analytical results show a fairly good fit to the experimental ones

  3. Web Analytics

    Science.gov (United States)

    EPA’s Web Analytics Program collects, analyzes, and provides reports on traffic, quality assurance, and customer satisfaction metrics for EPA’s website. The program uses a variety of analytics tools, including Google Analytics and CrazyEgg.

  4. Sci-Fri PM: Radiation Therapy, Planning, Imaging, and Special Techniques - 06: Patient-specific QA Procedure for Gated VMAT SABR Treatments using 10x Beam in Flattening-Filter Free Mode

    Energy Technology Data Exchange (ETDEWEB)

    Mestrovic, Ante; Chitsazzadeh, Shadi; Wells, Derek M.; Gray, Stephen [University of Calgary, Tom Baker Cancer Centre, Tom Baker Cancer Centre (Canada)

    2016-08-15

    Purpose: To develop a highly sensitive patient specific QA procedure for gated VMAT stereotactic ablative radiotherapy (SABR) treatments. Methods: A platform was constructed to attach the translational stage of a Quasar respiratory motion phantom to a pinpoint ion chamber insert and move the ion chamber inside the ArcCheck. The Quasar phantom controller uses a patient-specific breathing pattern to translate the ion chamber in a superior-inferior direction inside the ArcCheck. With this system the ion chamber is used to QA the correct phase of the gated delivery and the ArcCheck diodes are used to QA the overall dose distribution. This novel approach requires a single plan delivery for a complete QA of a gated plan. The sensitivity of the gating QA procedure was investigated with respect to the following parameters: PTV size, exhale duration, baseline drift, gating window size. Results: The difference between the measured dose to a point in the penumbra and the Eclipse calculated dose was under 2% for small residual motions. The QA procedure was independent of PTV size and duration of exhale. Baseline drift and gating window size, however, significantly affected the penumbral dose measurement, with differences of up to 30% compared to Eclipse. Conclusion: This study described a highly sensitive QA procedure for gated VMAT SABR treatments. The QA outcome was dependent on the gating window size and baseline drift. Analysis of additional patient breathing patterns is currently undergoing to determine a clinically relevant gating window size and an appropriate tolerance level for this procedure.

  5. Sensitivity of volumetric modulated arc therapy patient specific QA results to multileaf collimator errors and correlation to dose volume histogram based metrics.

    LENUS (Irish Health Repository)

    Coleman, Linda

    2013-11-01

    This study investigates the impact of systematic multileaf collimator (MLC) positional errors on gamma analysis results used for quality assurance (QA) of Rapidarc treatments. In addition, this study evaluates the relationship of these gamma analysis results and clinical dose volume histogram metrics (DVH) for Rapidarc treatment plans.

  6. SU-G-206-01: A Fully Automated CT Tool to Facilitate Phantom Image QA for Quantitative Imaging in Clinical Trials

    International Nuclear Information System (INIS)

    Wahi-Anwar, M; Lo, P; Kim, H; Brown, M; McNitt-Gray, M

    2016-01-01

    Purpose: The use of Quantitative Imaging (QI) methods in Clinical Trials requires both verification of adherence to a specified protocol and an assessment of scanner performance under that protocol, which are currently accomplished manually. This work introduces automated phantom identification and image QA measure extraction towards a fully-automated CT phantom QA system to perform these functions and facilitate the use of Quantitative Imaging methods in clinical trials. Methods: This study used a retrospective cohort of CT phantom scans from existing clinical trial protocols - totaling 84 phantoms, across 3 phantom types using various scanners and protocols. The QA system identifies the input phantom scan through an ensemble of threshold-based classifiers. Each classifier - corresponding to a phantom type - contains a template slice, which is compared to the input scan on a slice-by-slice basis, resulting in slice-wise similarity metric values for each slice compared. Pre-trained thresholds (established from a training set of phantom images matching the template type) are used to filter the similarity distribution, and the slice with the most optimal local mean similarity, with local neighboring slices meeting the threshold requirement, is chosen as the classifier’s matched slice (if it existed). The classifier with the matched slice possessing the most optimal local mean similarity is then chosen as the ensemble’s best matching slice. If the best matching slice exists, image QA algorithm and ROIs corresponding to the matching classifier extracted the image QA measures. Results: Automated phantom identification performed with 84.5% accuracy and 88.8% sensitivity on 84 phantoms. Automated image quality measurements (following standard protocol) on identified water phantoms (n=35) matched user QA decisions with 100% accuracy. Conclusion: We provide a fullyautomated CT phantom QA system consistent with manual QA performance. Further work will include parallel

  7. SU-G-206-01: A Fully Automated CT Tool to Facilitate Phantom Image QA for Quantitative Imaging in Clinical Trials

    Energy Technology Data Exchange (ETDEWEB)

    Wahi-Anwar, M; Lo, P; Kim, H; Brown, M; McNitt-Gray, M [UCLA Radiological Sciences, Los Angeles, CA (United States)

    2016-06-15

    Purpose: The use of Quantitative Imaging (QI) methods in Clinical Trials requires both verification of adherence to a specified protocol and an assessment of scanner performance under that protocol, which are currently accomplished manually. This work introduces automated phantom identification and image QA measure extraction towards a fully-automated CT phantom QA system to perform these functions and facilitate the use of Quantitative Imaging methods in clinical trials. Methods: This study used a retrospective cohort of CT phantom scans from existing clinical trial protocols - totaling 84 phantoms, across 3 phantom types using various scanners and protocols. The QA system identifies the input phantom scan through an ensemble of threshold-based classifiers. Each classifier - corresponding to a phantom type - contains a template slice, which is compared to the input scan on a slice-by-slice basis, resulting in slice-wise similarity metric values for each slice compared. Pre-trained thresholds (established from a training set of phantom images matching the template type) are used to filter the similarity distribution, and the slice with the most optimal local mean similarity, with local neighboring slices meeting the threshold requirement, is chosen as the classifier’s matched slice (if it existed). The classifier with the matched slice possessing the most optimal local mean similarity is then chosen as the ensemble’s best matching slice. If the best matching slice exists, image QA algorithm and ROIs corresponding to the matching classifier extracted the image QA measures. Results: Automated phantom identification performed with 84.5% accuracy and 88.8% sensitivity on 84 phantoms. Automated image quality measurements (following standard protocol) on identified water phantoms (n=35) matched user QA decisions with 100% accuracy. Conclusion: We provide a fullyautomated CT phantom QA system consistent with manual QA performance. Further work will include parallel

  8. Building Watson: An Overview of the DeepQA Project

    OpenAIRE

    Ferrucci, David; Brown, Eric; Chu-Carroll, Jennifer; Fan, James; Gondek, David; Kalyanpur, Aditya A.; Lally, Adam; Murdock, J. William; Nyberg, Eric; Prager, John; Schlaefer, Nico; Welty, Chris

    2010-01-01

    IBM Research undertook a challenge to build a computer system that could compete at the human champion level in real time on the American TV Quiz show, Jeopardy! The extent of the challenge includes fielding a real-time automatic contestant on the show, not merely a laboratory exercise. The Jeopardy! Challenge helped us address requirements that led to the design of the DeepQA architecture and the implementation of Watson. After 3 years of intense research and development by a core team of ab...

  9. ATLAS IBL Stave QA - In and Around SR1

    CERN Document Server

    Carney, Rebecca

    2013-01-01

    During the Phase-I upgrade the ATLAS Inner tracker will have a whole new layer of pixels inserted between the existing B-layer and a new, smaller, beam pipe. Briefly, there are 14 assemblies of 32 single and double-chip hybrid silicon pixel chips arranged side-by-side on light-weight, thermally conductive carbon-fibre coated carbon foam supports called staves. When the staves arrive at CERN, fully assembled, they undergo a QA procedure, which checks the power characteristics of sensors and read-out chips, and assess the quality of individual pixels.

  10. Common QA/QM Criteria for Multinational Vendor Inspection

    International Nuclear Information System (INIS)

    2014-01-01

    This VICWG document provides the 'Common QA/QM Criteria' which will be used in Multinational Vendor Inspection. The 'Common QA/QM Criteria' provides the basic consideration when performing the Vendor Inspection. These criteria has been developed in conformity with International Codes and Standards such as IAEA, ISO and so on that MDEP member countries adopted. The purpose of the VICWG is to establish areas of co-operation in the Vendor Inspection practices among MDEP member countries as described in the MDEP issue-specific Terms of Reference (ToR). As part of this, from the beginning, a survey was performed to understand and to identify areas of commonality and differences between regulatory practices of member countries in the area of vendor inspection. The VICWG also collaborated by performing Witnessed Inspections and Joint Inspections. Through these activities, it was recognized that member countries commonly apply the IAEA safety standard (GS-R-3) to the vendor inspection criteria, and almost ail European member countries apply the ISO standard (ISO9001). In the US, the NRC regulatory requirement in 10 CFR, Part 50, Appendix B is used. South Korea uses the same criteria as in the US. As a result of the information obtained, a comparison table between codes and standards (IAEAGS-R-3, ISO 9001:2008.10CFR50 Appendix Band ASME NQA-1) has been developed in order to inform the development of 'Common QA/QM Criteria'. The result is documented in Table 1, 'MDEP CORE QA/QM Requirement and Comparison between Codes and Standards'. In addition, each country's criteria were compared with the US 10CFR50 Appendix B as a template. Table 2 shows VICWG Survey on Quality Assurance Program Requirements. Through these activities above, we considered that the core requirements should be consistent with both IAEA safety standard and ISO standard, and considered that the common requirements in the US 10CFR50 Appendix B used to the survey

  11. Enriching consumer health vocabulary through mining a social Q&A site: A similarity-based approach.

    Science.gov (United States)

    He, Zhe; Chen, Zhiwei; Oh, Sanghee; Hou, Jinghui; Bian, Jiang

    2017-05-01

    The widely known vocabulary gap between health consumers and healthcare professionals hinders information seeking and health dialogue of consumers on end-user health applications. The Open Access and Collaborative Consumer Health Vocabulary (OAC CHV), which contains health-related terms used by lay consumers, has been created to bridge such a gap. Specifically, the OAC CHV facilitates consumers' health information retrieval by enabling consumer-facing health applications to translate between professional language and consumer friendly language. To keep up with the constantly evolving medical knowledge and language use, new terms need to be identified and added to the OAC CHV. User-generated content on social media, including social question and answer (social Q&A) sites, afford us an enormous opportunity in mining consumer health terms. Existing methods of identifying new consumer terms from text typically use ad-hoc lexical syntactic patterns and human review. Our study extends an existing method by extracting n-grams from a social Q&A textual corpus and representing them with a rich set of contextual and syntactic features. Using K-means clustering, our method, simiTerm, was able to identify terms that are both contextually and syntactically similar to the existing OAC CHV terms. We tested our method on social Q&A corpora on two disease domains: diabetes and cancer. Our method outperformed three baseline ranking methods. A post-hoc qualitative evaluation by human experts further validated that our method can effectively identify meaningful new consumer terms on social Q&A. Copyright © 2017 Elsevier Inc. All rights reserved.

  12. UMTRA project water sampling and analysis plan, Tuba City, Arizona

    International Nuclear Information System (INIS)

    1996-02-01

    Planned, routine ground water sampling activities at the U.S. Department of Energy (DOE) Uranium Mill Tailings Remedial Action (UMTRA) Project site in Tuba City, Arizona, are described in the following sections of this water sampling and analysis plan (WSAP). This plan identifies and justifies the sampling locations, analytical parameters, detection limits, and sampling frequency for the stations routinely monitored at the site. The ground water data are used for site characterization and risk assessment. The regulatory basis for routine ground water monitoring at UMTRA Project sites is derived from the U.S. Environmental Protection Agency (EPA) regulations in 40 CFR Part 192 (1994) and the final EPA standards of 1995 (60 FR 2854). Sampling procedures are guided by the UMTRA Project standard operating procedures (SOP) (JEG, n.d.), and the most effective technical approach for the site

  13. The impact of Arizona Highways Magazine's facebook page.

    Science.gov (United States)

    2014-02-01

    This project examined the relationship between use of the Arizona Highways magazine (AHM) Facebook Page and the decision to : travel to or within Arizona. Key purposes were to: (1) provide a thorough understanding of AHM Facebook Page users, includin...

  14. 21 CFR 866.3035 - Arizona spp. serological reagents.

    Science.gov (United States)

    2010-04-01

    ... (CONTINUED) MEDICAL DEVICES IMMUNOLOGY AND MICROBIOLOGY DEVICES Serological Reagents § 866.3035 Arizona spp... antisera and antigens used to identify Arizona spp. in cultured isolates derived from clinical specimens...

  15. Analytical and experimental study of two concentric cylinders coupled by a fluid gap

    International Nuclear Information System (INIS)

    Mulcahy, T.M.; Turula, P.; Chung, H.; Jendrzejczyk, J.A.

    1975-04-01

    A breeder reactor vessel is a substantial steel cylinder which is partially protected from the nuclear reaction temperature by a relatively thin concentric shell separated from the vessel by a narrow fluid-filled gap. An experimental and analytical study of the vibration of a model of such a shell used in the Fast Test Reactor is described. The analytical work consists first using a free vibration solution of the shell in vacuum as a basis for extrapolating vibration behavior for the same shell with a fluid gap. Then a direct finite element solution is found for the actual problem--the shell and the fluid coupling it to the rigid outer container. All the finite element computations were carried out using the NASTRAN program. The experimental setup consisted of a steel sheet rolled and welded into a cylinder, free at the top edge and at the bottom soldered to a disc which in turn was bolted to a heavy base plate. The fluid gap was provided by using a thick concrete shell as the outer cylinder. A series of these cylinders was used to provide several sizes of annular gap. The case of the steel shell alone, without fluid, was also considered. The steel cylinder was vibrated by an electromagnetic exciter using both harmonic loading and random loading functions. In general, correspondence of experimental and analytical results is within acceptable limits; however, several vibration modes corresponding to solutions with low circumferential wave numbers were not detected experimentally. Response analysis performed to compare the response amplitude at various modes indicates that the intensity at the modes in question is very low. (U.S.)

  16. Analytical pyrolysis-based study on intra-skeletal organic matrices from Mediterranean corals.

    Science.gov (United States)

    Adamiano, Alessio; Goffredo, Stefano; Dubinsky, Zvy; Levy, Oren; Fermani, Simona; Fabbri, Daniele; Falini, Giuseppe

    2014-09-01

    Off-line analytical pyrolysis combined with gas chromatography–mass spectroscopy (GC–MS), directly or after trimethylsilylation, along with infrared spectroscopy and amino acid analysis was applied for the first time to the characterization of the intra-skeletal organic matrix (OM) extracted from four Mediterranean hard corals. They were diverse in growth form and trophic strategy namely Balanophyllia europaea and Leptopsammia pruvoti—solitary corals, only the first having zooxanthelle—and Cladocora caespitosa and Astroides calycularis—colonial corals, only the first with zooxanthelle. Pyrolysis products evolved from OM could be assigned to lipid (e.g. fatty acids, fatty alcohols, monoacylglicerols), protein (e.g. 2,5-diketopiperazines, DKPs) and polysaccharide (e.g. anhydrosugars) precursors. Their quantitative distribution showed for all the species a low protein content with respect to lipids and polysaccharides. A chemometric approach using principal component analysis (PCA) and clustering analysis was applied on OM mean amino acidic compositions. The small compositional diversity across coral species was tentatively related with coral growth form. The presence of N-acetyl glucosamine markers suggested a functional link with other calcified tissues containing chitin. The protein fraction was further investigated using novel DKP markers tentatively identified from analytical pyrolysis of model polar linear dipeptides. Again, no correlation was observed in relation to coral ecology. These analytical results revealed that the bulk structure and composition of OMs among studied corals are similar, as it is the textural organization of the skeleton mineralized units. Therefore, they suggest that coral’s biomineralization is governed by similar macromolecules, and probably mechanisms, independently from their ecology.

  17. On New Families of Integrals in Analytical Studies of Superconductors within the Conformal Transformation Method

    Directory of Open Access Journals (Sweden)

    Ryszard Gonczarek

    2015-01-01

    Full Text Available We show that, by applying the conformal transformation method, strongly correlated superconducting systems can be discussed in terms of the Fermi liquid with a variable density of states function. Within this approach, it is possible to formulate and carry out purely analytical study based on a set of fundamental equations. After presenting the mathematical structure of the s-wave superconducting gap and other quantitative characteristics of superconductors, we evaluate and discuss integrals inherent in fundamental equations describing superconducting systems. The results presented here extend the approach formulated by Abrikosov and Maki, which was restricted to the first-order expansion. A few infinite families of integrals are derived and allow us to express the fundamental equations by means of analytical formulas. They can be then exploited in order to find quantitative characteristics of superconducting systems by the method of successive approximations. We show that the results can be applied in studies of high-Tc superconductors and other superconducting materials of the new generation.

  18. An analytical model for the study of a small LFR core dynamics: development and benchmark

    International Nuclear Information System (INIS)

    Bortot, S.; Cammi, A.; Lorenzi, S.; Moisseytsev, A.

    2011-01-01

    An analytical model for the study of a small Lead-cooled Fast Reactor (LFR) control-oriented dynamics has been developed aimed at providing a useful, very flexible and straightforward, though accurate, tool allowing relatively quick transient design-basis and stability analyses. A simplified lumped-parameter approach has been adopted to couple neutronics and thermal-hydraulics: the point-kinetics approximation has been employed and an average-temperature heat-exchange model has been implemented. The reactor transient responses following postulated accident initiators such as Unprotected Control Rod Withdrawal (UTOP), Loss of Heat Sink (ULOHS) and Loss of Flow (ULOF) have been studied for a MOX and a metal-fuelled core at the Beginning of Cycle (BoC) and End of Cycle (EoC) configurations. A benchmark analysis has been then performed by means of the SAS4A/SASSYS-1 Liquid Metal Reactor Code System, in which a core model based on three representative channels has been built with the purpose of providing verification for the analytical outcomes and indicating how the latter relate to more realistic one-dimensional calculations. As a general result, responses concerning the main core characteristics (namely, power, reactivity, etc.) have turned out to be mutually consistent in terms of both steady-state absolute figures and transient developments, showing discrepancies of the order of only some percents, thus confirming a very satisfactory agreement. (author)

  19. Natural phenolic antioxidants in human fluids: analytical approaches and antioxidant capacity studies

    International Nuclear Information System (INIS)

    Zhang, K.; Zuo, Y.

    2006-01-01

    Phenolic compounds are the most abundant natural antioxidants in our diet. Epidemiological studies have shown the possible prevention effects of consumption of fruits and vegetables rich in phenolic compounds on degenerative diseases, such as cardiovascular diseases and cancers. However, there is a serious lack of fundamental knowledge on the uptake and metabolism of phenolic compounds in humans. It is clear that phenolic molecules, only absorbed by humans, can exert biological effects. This review presents a current knowledge on the analytical methods, antioxidant capacity measurements, as well as research strategies related to natural phenolic antioxidants on human health. Both GC-MS and LC-MS have proved to be very useful analytical techniques that can be employed to identify and quantitate targeted phenolic antioxidants and their metabolites in biofluids. Free radical quenching tests provide a direct measurement of antioxidant capacity but lack specificity and may oversimplify the in vivo human physiological environment. Research strategies are diverse and mainly focused on positive health effect of antioxidants. In the future studies, multiple potential bioactivities, both positive and negative, should be considered. (author)

  20. Study on dynamic characteristics of reduced analytical model for PWR reactor internal structures

    International Nuclear Information System (INIS)

    Yoo, Bong; Lee, Jae Han; Kim, Jong Bum; Koo, Kyeong Hoe

    1993-01-01

    The objective of this study is to establish the procedure of the reduced analytical modeling technique for the PWR reactor internal(RI) structures and to carry out the sensitivity study of the dynamic characteristics of the structures by varying the structural parameters such as the stiffness, the mass and the damping. Modeling techniques for the PWR reactor internal structures and computer programs used for the dynamic analysis of the reactor internal structures are briefly investigated. Among the many components of RI structures, the dynamic characteristics for CSB was performed. The sensitivity analysis of the dynamic characteristics for the reduced analytical model considering the variations of the stiffnesses for the lower and upper flanges of the CSB and for the RV Snubber were performed to improve the dynamic characteristics of the RI structures against the external loadings given. In order to enhance the structural design margin of the RI components, the nonlinear time history analyses were attempted for the RI reduced models to compare the structural responses between the reference model and the modified one. (Author)

  1. An analytical and numerical study of solar chimney use for room natural ventilation

    Energy Technology Data Exchange (ETDEWEB)

    Bassiouny, Ramadan; Koura, Nader S.A. [Department of Mechanical Power Engineering and Energy, Minia University, Minia 61111 (Egypt)

    2008-07-01

    The solar chimney concept used for improving room natural ventilation was analytically and numerically studied. The study considered some geometrical parameters such as chimney inlet size and width, which are believed to have a significant effect on space ventilation. The numerical analysis was intended to predict the flow pattern in the room as well as in the chimney. This would help optimizing design parameters. The results were compared with available published experimental and theoretical data. There was an acceptable trend match between the present analytical results and the published data for the room air change per hour, ACH. Further, it was noticed that the chimney width has a more significant effect on ACH compared to the chimney inlet size. The results showed that the absorber average temperature could be correlated to the intensity as: (T{sub w} = 3.51I{sup 0.461}) with an accepted range of approximation error. In addition the average air exit velocity was found to vary with the intensity as ({nu}{sub ex} = 0.013I{sup 0.4}). (author)

  2. Possibilities and limits of multiprofessional attention in the care of psychiatric emergencies: analytical study

    Directory of Open Access Journals (Sweden)

    Fernanda Lima de Paula

    2017-05-01

    Full Text Available Goal: to analyze the possibilities and limits of multiprofessional care in the attention to psychiatric emergencies. Method: it is an analytical study of the type integrative review of the comprehensive literature. Searches were conducted in the Latin American and Caribbean Literature (LILACS and Nursing Database (BDENF databases and in the ScieLo Virtual Library, with the use of Descriptors in Health Sciences (DECs: “Emergency Services, Psychiatric”, “Forensic Psychiatry”, “Psychiatric Rehabilitation”, in the period from 2007 to 2017. Results: after data analysis, two thematic categories emerged: “Possibilities and limits in multiprofessional care for patients in crisis” and “The continuity of care to the patient in crisis by the multiprofessional team”. The studies point out fragility in the management of the multiprofessional team of care to the patients in psychiatric crisis. Therefore, in the substitutive services to the psychiatric hospital, it is necessary to strengthen the care and bonding tools for continuity of treatment after the cases of psychiatric emergency of these patients. Conclusion: this research provided a deepening of the knowledge regarding the challenges of the multiprofessional team in the care of analytical psychiatric emergencies and in relation to the patient in crisis, considering the main multiprofessional actions, understanding how this approach is done and patient follow-up. Descriptors: Emergency Services, Psychiatric. Forensic Psychiatry. Psychiatric Rehabilitation.

  3. EMPLOYEE PROMOTION PLANNING IN ANALYTICAL HIERARCHY PROCESS PERSPECTIVE: STUDY ON NATIONAL PUBLIC PROCUREMENT AGENCY

    Directory of Open Access Journals (Sweden)

    Ayuningtyas A.K.

    2017-10-01

    Full Text Available The promotion process is part of the career development conducted by Civil State Apparatus Employee (Pegawai Aparatur Sipil Negara which should be implemented by applying merit system. Employee-related strategic decision making has not applied merit system as mandated in applied laws. It occurred due to Public Service Appointment Board (Badan Pertimbangan Jabatan dan Kepangkatan not possessing assessment model and criteria which could be used to support promotion process implementation in the appropriate structural position based on employee competence and performance. This study aims to describe and analyze assessment criteria and subcriteria required to be considered in State Civil Servant Officers promotion planning by applying Analytical Hierarchy Process (AHP method in National Public Procurement Agency (Lembaga Kebijakan Pengadaan Barang/Jasa Pemerintah. This study uses the explanative quantitative univariate method. Data collection technique used questionnaire instrument. Analytical tool used was AHP. Research result exhibits that ASN employee promotion planning using assessment model is described as follows: Employee Performance Assessment consist of Employee Work Performance element with three criteria and Employee Work Behavior with twenty-three criteria; and Evaluation of Employee Promotion Implementation with eleven criteria. Through the use of AHP methods employee, promotion planning could be utilized as a tool for Baperjakat to produce employee decisions that will be promoted objectively and effectively.

  4. An analytical model and parametric study of electrical contact resistance in proton exchange membrane fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Zhiliang; Wang, Shuxin; Zhang, Lianhong [School of Mechanical Engineering, Tianjin University, Tianjin 300072 (China); Hu, S. Jack [Department of Mechanical Engineering, The University of Michigan, Ann Arbor, MI 48109-2125 (United States)

    2009-04-15

    This paper presents an analytical model of the electrical contact resistance between the carbon paper gas diffusion layers (GDLs) and the graphite bipolar plates (BPPs) in a proton exchange membrane (PEM) fuel cell. The model is developed based on the classical statistical contact theory for a PEM fuel cell, using the same probability distributions of the GDL structure and BPP surface profile as previously described in Wu et al. [Z. Wu, Y. Zhou, G. Lin, S. Wang, S.J. Hu, J. Power Sources 182 (2008) 265-269] and Zhou et al. [Y. Zhou, G. Lin, A.J. Shih, S.J. Hu, J. Power Sources 163 (2007) 777-783]. Results show that estimates of the contact resistance compare favorably with experimental data by Zhou et al. [Y. Zhou, G. Lin, A.J. Shih, S.J. Hu, J. Power Sources 163 (2007) 777-783]. Factors affecting the contact behavior are systematically studied using the analytical model, including the material properties of the two contact bodies and factors arising from the manufacturing processes. The transverse Young's modulus of chopped carbon fibers in the GDL and the surface profile of the BPP are found to be significant to the contact resistance. The factor study also sheds light on the manufacturing requirements of carbon fiber GDLs for a better contact performance in PEM fuel cells. (author)

  5. Experimental and analytical studies on the vibration serviceability of long-span prestressed concrete floor

    Science.gov (United States)

    Cao, Liang; Liu, Jiepeng; Li, Jiang; Zhang, Ruizhi

    2018-04-01

    An extensive experimental and theoretical research study was undertaken to study the vibration serviceability of a long-span prestressed concrete floor system to be used in the lounge of a major airport. Specifically, jumping impact tests were carried out to obtain the floor's modal parameters, followed by an analysis of the distribution of peak accelerations. Running tests were also performed to capture the acceleration responses. The prestressed concrete floor was found to have a low fundamental natural frequency (≈ 8.86 Hz) corresponding to the average modal damping ratio of ≈ 2.17%. A coefficients β rp is proposed for convenient calculation of the maximum root-mean-square acceleration for running. In the theoretical analysis, the prestressed concrete floor under running excitation is treated as a two-span continuous anisotropic rectangular plate with simply-supported edges. The calculated analytical results (natural frequencies and root-mean-square acceleration) agree well with the experimental ones. The analytical approach is thus validated.

  6. Service Quality of Online Shopping Platforms: A Case-Based Empirical and Analytical Study

    Directory of Open Access Journals (Sweden)

    Tsan-Ming Choi

    2013-01-01

    Full Text Available Customer service is crucially important for online shopping platforms (OSPs such as eBay and Taobao. Based on the well-established service quality instruments and the scenario of the specific case on Taobao, this paper focuses on exploring the service quality of an OSP with an aim of revealing customer perceptions of the service quality associated with the provided functions and investigating their impacts on customer loyalty. By an empirical study, this paper finds that the “fulfillment and responsiveness” function is significantly related to the customer loyalty. Further analytical study is conducted to reveal that the optimal service level on the “fulfillment and responsiveness” function for the risk averse OSP uniquely exists. Moreover, the analytical results prove that (i if the customer loyalty is more positively correlated to the service level, it will lead to a larger optimal service level, and (ii the optimal service level is independent of the profit target, the source of uncertainty, and the risk preference of the OSP.

  7. The path dependency theory: analytical framework to study institutional integration. The case of France.

    Science.gov (United States)

    Trouvé, Hélène; Couturier, Yves; Etheridge, Francis; Saint-Jean, Olivier; Somme, Dominique

    2010-06-30

    The literature on integration indicates the need for an enhanced theorization of institutional integration. This article proposes path dependence as an analytical framework to study the systems in which integration takes place. PRISMA proposes a model for integrating health and social care services for older adults. This model was initially tested in Quebec. The PRISMA France study gave us an opportunity to analyze institutional integration in France. A qualitative approach was used. Analyses were based on semi-structured interviews with actors of all levels of decision-making, observations of advisory board meetings, and administrative documents. Our analyses revealed the complexity and fragmentation of institutional integration. The path dependency theory, which analyzes the change capacity of institutions by taking into account their historic structures, allows analysis of this situation. The path dependency to the Bismarckian system and the incomplete reforms of gerontological policies generate the coexistence and juxtaposition of institutional systems. In such a context, no institution has sufficient ability to determine gerontology policy and build institutional integration by itself. Using path dependence as an analytical framework helps to understand the reasons why institutional integration is critical to organizational and clinical integration, and the complex construction of institutional integration in France.

  8. Maternal and infant activity: Analytic approaches for the study of circadian rhythm.

    Science.gov (United States)

    Thomas, Karen A; Burr, Robert L; Spieker, Susan

    2015-11-01

    The study of infant and mother circadian rhythm entails choice of instruments appropriate for use in the home environment as well as selection of analytic approach that characterizes circadian rhythm. While actigraphy monitoring suits the needs of home study, limited studies have examined mother and infant rhythm derived from actigraphy. Among this existing research a variety of analyses have been employed to characterize 24-h rhythm, reducing ability to evaluate and synthesize findings. Few studies have examined the correspondence of mother and infant circadian parameters for the most frequently cited approaches: cosinor, non-parametric circadian rhythm analysis (NPCRA), and autocorrelation function (ACF). The purpose of this research was to examine analytic approaches in the study of mother and infant circadian activity rhythm. Forty-three healthy mother and infant pairs were studied in the home environment over a 72h period at infant age 4, 8, and 12 weeks. Activity was recorded continuously using actigraphy monitors and mothers completed a diary. Parameters of circadian rhythm were generated from cosinor analysis, NPCRA, and ACF. The correlation among measures of rhythm center (cosinor mesor, NPCRA mid level), strength or fit of 24-h period (cosinor magnitude and R(2), NPCRA amplitude and relative amplitude (RA)), phase (cosinor acrophase, NPCRA M10 and L5 midpoint), and rhythm stability and variability (NPCRA interdaily stability (IS) and intradaily variability (IV), ACF) was assessed, and additionally the effect size (eta(2)) for change over time evaluated. Results suggest that cosinor analysis, NPCRA, and autocorrelation provide several comparable parameters of infant and maternal circadian rhythm center, fit, and phase. IS and IV were strongly correlated with the 24-h cycle fit. The circadian parameters analyzed offer separate insight into rhythm and differing effect size for the detection of change over time. Findings inform selection of analysis and

  9. Green supply chain management strategy selection using analytic network process: case study at PT XYZ

    Science.gov (United States)

    Adelina, W.; Kusumastuti, R. D.

    2017-01-01

    This study is about business strategy selection for green supply chain management (GSCM) for PT XYZ by using Analytic Network Process (ANP). GSCM is initiated as a response to reduce environmental impacts from industrial activities. The purposes of this study are identifying criteria and sub criteria in selecting GSCM Strategy, and analysing a suitable GSCM strategy for PT XYZ. This study proposes ANP network with 6 criteria and 29 sub criteria, which are obtained from the literature and experts’ judgements. One of the six criteria contains GSCM strategy options, namely risk-based strategy, efficiency-based strategy, innovation-based strategy, and closed loop strategy. ANP solves complex GSCM strategy-selection by using a more structured process and considering green perspectives from experts. The result indicates that innovation-based strategy is the most suitable green supply chain management strategy for PT XYZ.

  10. Nuclear legislation analytical study. Regulatory and institutional framework for nuclear activities

    International Nuclear Information System (INIS)

    1997-01-01

    This study is the second update of the 1995 edition of a series of analytical studies on nuclear legislation in OECD member countries, prepared by the OECD Nuclear Energy Agency (NEA) with the co-operation of the countries concerned. It is organised on the basis of a standardised format for all countries, thus facilitating the comparison of information. This study deals with national legislations concerning nuclear third party liability and other aspects of nuclear laws (transport, radiation protection, trade, radioactive waste management, public and semi-public agencies...). The 1997 update consists of replacement chapters for Australia, France, Germany, Korea, Norway, Sweden, and the United Kingdom. In addition, there are completely new chapters for the Czech Republic, Hungary and Poland. (A.L.B.)

  11. Learning Analytics focused on student behavior. Case study: dropout in distance learning institutions

    Directory of Open Access Journals (Sweden)

    Jose Aguilar

    2017-04-01

    Full Text Available Normally, Learning Analytics (LA can be focused on the analysis of the learning process or the student behavior. In this paper is analyzed the use of LA in the context of distance learning universities, particularly focuses on the students’ behavior. We propose to use a new concept, called "Autonomic Cycle of Learning Analysis Tasks", which defines a set of tasks of LA, whose common objective is to achieve an improvement in the process under study. In this paper, we develop the "Autonomic Cycle of LA Tasks" to analyze the dropout in distance learning institutions. We use a business intelligence methodology in order to develop the "Autonomic Cycle of LA Tasks" for the analysis of the dropout in distance learning. The Autonomic Cycle identifies factors that influence the decision of a student to abandon their studies, predicts the potentially susceptible students to abandon their university studies, and define a motivational pattern for these students.

  12. Chasing the effects of Pre-analytical Confounders - a Multicentre Study on CSF-AD biomarkers

    Directory of Open Access Journals (Sweden)

    Maria Joao Leitao

    2015-07-01

    Full Text Available Core cerebrospinal fluid (CSF biomarkers-Aβ42, Tau and pTau–have been recently incorporated in the revised criteria for Alzheimer’s disease (AD. However, their widespread clinical application lacks standardization. Pre-analytical sample handling and storage play an important role in the reliable measurement of these biomarkers across laboratories. In this study, we aim to surpass the efforts from previous studies, by employing a multicentre approach to assess the impact of less studied CSF pre-analytical confounders in AD-biomarkers quantification. Four different centres participated in this study and followed the same established protocol. CSF samples were analysed for three biomarkers (Aβ42, Tau and pTau and tested for different spinning conditions (temperature: Room temperature (RT vs. 4oC; speed: 500g vs. 2000g vs. 3000g, storage volume variations (25%, 50% and 75% of tube total volume as well as freezing-thaw cycles (up to 5 cyles. The influence of sample routine parameters, inter-centre variability and relative value of each biomarker (reported as normal/abnormal, was analysed. Centrifugation conditions did not influence biomarkers levels, except for samples with a high CSF total protein content, where either non centrifugation or centrifugation at RT, compared to 4ºC, led to higher Aβ42 levels. Reducing CSF storage volume from 75% to 50% of total tube capacity, decreased Aβ42 concentration (within analytical CV of the assay, whereas no change in Tau or pTau was observed. Moreover, the concentration of Tau and pTau appears to be stable up to 5 freeze-thaw cycles, whereas Aβ42 levels decrease if CSF is freeze-thawed more than 3 times. This systematic study reinforces the need for CSF centrifugation at 4ºC prior to storage and highlights the influence of storage conditions in Aβ42 levels. This study contributes to the establishment of harmonized standard operating procedures that will help reducing inter-lab variability of CSF

  13. Multimodal follow-up questions to multimodal answers in a QA system

    NARCIS (Netherlands)

    van Schooten, B.W.; op den Akker, Hendrikus J.A.

    2007-01-01

    We are developing a dialogue manager (DM) for a multimodal interactive Question Answering (QA) system. Our QA system presents answers using text and pictures, and the user may pose follow-up questions using text or speech, while indicating screen elements with the mouse. We developed a corpus of

  14. Application of QA grading to Yucca Mountain Site Characterization Project items and activities

    International Nuclear Information System (INIS)

    Murthy, R.B.; Smith, S.C.

    1991-01-01

    Grading is the act of selecting the quality assurance (QA) measures necessary to develop and maintain confidence in the quality of an item or activity. The list of QA measures from which this selection is made are the 20 criteria of the Yucca Mountain Site Characterization Project Quality Assurance Requirements Document

  15. Poster - Thur Eve - 29: Detecting changes in IMRT QA using statistical process control.

    Science.gov (United States)

    Drever, L; Salomons, G

    2012-07-01

    Statistical process control (SPC) methods were used to analyze 239 measurement based individual IMRT QA events. The selected IMRT QA events were all head and neck (H&N) cases with 70Gy in 35 fractions, and all prostate cases with 76Gy in 38 fractions planned between March 2009 and 2012. The results were used to determine if the tolerance limits currently being used for IMRT QA were able to indicate if the process was under control. The SPC calculations were repeated for IMRT QA of the same type of cases that were planned after the treatment planning system was upgraded from Eclipse version 8.1.18 to version 10.0.39. The initial tolerance limits were found to be acceptable for two of the three metrics tested prior to the upgrade. After the upgrade to the treatment planning system the SPC analysis found that the a priori limits were no longer capable of indicating control for 2 of the 3 metrics analyzed. The changes in the IMRT QA results were clearly identified using SPC, indicating that it is a useful tool for finding changes in the IMRT QA process. Routine application of SPC to IMRT QA results would help to distinguish unintentional trends and changes from the random variation in the IMRT QA results for individual plans. © 2012 American Association of Physicists in Medicine.

  16. Technical report on comparative analysis of ASME QA requirements and ISO series

    International Nuclear Information System (INIS)

    Kim, Kwan Hyun

    2000-06-01

    This technical report provides the differences on the QA requirement ASME and ISO in nuclear fields. This report applies to the quality assurance(QA) programmes of the design of two requirement. The organization having overall responsibility for the nuclear design, preservation, fabrication shall be described in this report in each stage of design project

  17. QA practice for online analyzers in water steam cycles

    International Nuclear Information System (INIS)

    Staub, L.

    2010-01-01

    The liberalization of power markets throughout the world has resulted in more and more power stations being operated in cycling mode, with frequent load changes and multiple daily start-up and shut-down cycles. This more flexible operation also calls for better automation and poses new challenges to water chemistry in water steam cycles, to avoid subsequent damage to vital plant components such as turbines, boilers or condensers. But automation for the most important chemistry control tool, the sampling and online analyzer system, is only possible if chemists can rely on their online analysis equipment. Proof of plausibility as well as reliability and availability of online analysis results becomes a major focus. While SOP and standard QA procedures for laboratory equipment are well established and daily practice, such measures are widely neglected for online process analyzers. This paper is aiming to establish a roadmap for the implementation of SOP and QA/QC procedures for online instruments in water steam cycles, leading to reliable chemical information that is trustworthy for process automation and chemistry control in water steam cycles. (author)

  18. QA practice for online analyzers in water steam cycles

    International Nuclear Information System (INIS)

    Staub Lukas

    2009-01-01

    The liberalization of power markets throughout the world has resulted in more and more power stations being operated in cycling mode, with frequent load changes and multiple daily start-up and shut-down cycles. This more flexible operation also calls for better automation and poses new challenges to water chemistry in water steam cycles, to avoid subsequent damage to vital plant components such as turbines, boilers or condensers. But automation for the most important chemistry control tool, the sampling and online analyzer system, is only possible if chemists can rely on their online analysis equipment. Proof of plausibility as well as reliability and availability of online analysis results becomes a major focus. While SOP and standard QA procedures for laboratory equipment are well established and daily practice, such measures are widely neglected for online process analyzers. This paper is aiming to establish a roadmap for the implementation of SOP and QA/QC procedures for online instruments in water steam cycles, leading to reliable chemical information that is trustworthy for process automation and chemistry control in water steam cycles. (author)

  19. Poster - 10: QA of Ultrasound Images for Prostate Brachytherapy

    Energy Technology Data Exchange (ETDEWEB)

    Szpala, Stanislaw; Kohli, Kirpal S. [BCCA-Fraser Valley Centre (Canada)

    2016-08-15

    Purpose: The current QA protocol of ultrasound systems used in prostate brachytherapy (TG128) addresses geometrical verifications, but the scope of evaluation of image quality is limited. We recognized importance of the latter in routine practice, and designed a protocol for QA of the images. Methods: Images of an ultrasound prostate phantom (CIRS053) were collected with BK Flex Focus 400. The images were saved as bmp after adjusting the gain to 50% for consistent results. Mean pixel values and signal to noise ratio were inspected in the representative sections of the phantom, including the mock prostate and the unechoic medium. Constancy of these numbers over a one year period was looked at. Results: The typical intensity in the mock prostate region in the transverse images ranged between 95 and 118 (out of 256), and the signal to noise was about 10. The intensity in the urethra region was about 170±40, and the unechoic medium was 2±2. The mean and the signal to noise ratio remained almost unchanged after a year, while the signal in the unechoic medium increased to about 7±4. Similar values were obtained in the sagittal images. Conclusions: The image analysis discussed above allows quick evaluation of constancy of the image quality. This may be also useful in troubleshooting image-quality problems during routine exams, which might not be due to deterioration of the US system, but other reasons, e.g. variations in tissue properties or air being trapped between the probe and the anatomy.

  20. Visual analytics for multimodal social network analysis: a design study with social scientists.

    Science.gov (United States)

    Ghani, Sohaib; Kwon, Bum Chul; Lee, Seungyoon; Yi, Ji Soo; Elmqvist, Niklas

    2013-12-01

    Social network analysis (SNA) is becoming increasingly concerned not only with actors and their relations, but also with distinguishing between different types of such entities. For example, social scientists may want to investigate asymmetric relations in organizations with strict chains of command, or incorporate non-actors such as conferences and projects when analyzing coauthorship patterns. Multimodal social networks are those where actors and relations belong to different types, or modes, and multimodal social network analysis (mSNA) is accordingly SNA for such networks. In this paper, we present a design study that we conducted with several social scientist collaborators on how to support mSNA using visual analytics tools. Based on an openended, formative design process, we devised a visual representation called parallel node-link bands (PNLBs) that splits modes into separate bands and renders connections between adjacent ones, similar to the list view in Jigsaw. We then used the tool in a qualitative evaluation involving five social scientists whose feedback informed a second design phase that incorporated additional network metrics. Finally, we conducted a second qualitative evaluation with our social scientist collaborators that provided further insights on the utility of the PNLBs representation and the potential of visual analytics for mSNA.

  1. Analytical study of Yang–Mills theory in the infrared from first principles

    Energy Technology Data Exchange (ETDEWEB)

    Siringo, Fabio, E-mail: fabio.siringo@ct.infn.it

    2016-06-15

    Pure Yang–Mills SU(N) theory is studied in the Landau gauge and four dimensional space. While leaving the original Lagrangian unmodified, a double perturbative expansion is devised, based on a massive free-particle propagator. In dimensional regularization, all diverging mass terms cancel exactly in the double expansion, without the need to include mass counterterms that would spoil the symmetry of the Lagrangian. No free parameters are included that were not in the original theory, yielding a fully analytical approach from first principles. The expansion is safe in the infrared and is equivalent to the standard perturbation theory in the UV. At one-loop, explicit analytical expressions are given for the propagators and the running coupling and are found in excellent agreement with the data of lattice simulations. A universal scaling property is predicted for the inverse propagators and shown to be satisfied by the lattice data. Higher loops are found to be negligible in the infrared below 300 MeV where the coupling becomes small and the one-loop approximation is under full control.

  2. Analytical study on the determination of boron in environmental water samples

    International Nuclear Information System (INIS)

    Lopez, F.J.; Gimenez, E.; Hernandez, F.

    1993-01-01

    An analytical study on the determination of boron in environmental water samples was carried out. The curcumin and carmine standard methods were compared with the most recent Azomethine-H method in order to evaluate their analytical characteristics and feasibility for the analysis of boron in water samples. Analyses of synthetic water, ground water, sea water and waste water samples were carried out and a statistical evaluation of the results was made. The Azomethine-H method was found to be the most sensitive (detection limit 0.02 mg l -1 ) and selective (no interference of commonly occurring ions in water was observed), showing also the best precision (relative standard deviation lower than 4%). Moreover, it gave good results for all types of samples analyzed. The accuracy of this method was tested by the addition of known amounts of standard solutions to different types of water samples. The slopes of standard additions and direct calibration graphs were similar and recoveries of added boron ranged from 99 to 107%. (orig.)

  3. Environmental concentrations of engineered nanomaterials: Review of modeling and analytical studies

    International Nuclear Information System (INIS)

    Gottschalk, Fadri; Sun, TianYin; Nowack, Bernd

    2013-01-01

    Scientific consensus predicts that the worldwide use of engineered nanomaterials (ENM) leads to their release into the environment. We reviewed the available literature concerning environmental concentrations of six ENMs (TiO 2 , ZnO, Ag, fullerenes, CNT and CeO 2 ) in surface waters, wastewater treatment plant effluents, biosolids, sediments, soils and air. Presently, a dozen modeling studies provide environmental concentrations for ENM and a handful of analytical works can be used as basis for a preliminary validation. There are still major knowledge gaps (e.g. on ENM production, application and release) that affect the modeled values, but over all an agreement on the order of magnitude of the environmental concentrations can be reached. True validation of the modeled values is difficult because trace analytical methods that are specific for ENM detection and quantification are not available. The modeled and measured results are not always comparable due to the different forms and sizes of particles that these two approaches target. -- Highlights: •Modeled environmental concentrations of engineered nanomaterials are reviewed. •Measured environmental concentrations of engineered nanomaterials are reviewed. •Possible validation of modeled data by measurements is critically evaluated. •Different approaches in modeling and measurement methods complicate validation. -- Modeled and measured environmental concentrations of engineered nanomaterials are reviewed and critically discussed

  4. An analytical study on the static vertical stiffness of wire rope isolators

    Energy Technology Data Exchange (ETDEWEB)

    Balaji, P. S.; Rahman, M. E.; Ho, Lau Hieng [Curtin University Sarawak, Miri (Malaysia); Moussa, Leblouba [University of Sharjah, Sharjah (United Arab Emirates)

    2016-01-15

    The vibrations caused by earthquake ground motions or the operations of heavy machineries can affect the functionality of equipment and cause damages to the hosting structures and surrounding equipment. A Wire rope isolator (WRI), which is a type of passive isolator known to be effective in isolating shocks and vibrations, can be used for vibration isolation of lightweight structures and equipment. The primary advantage of the WRI is that it can provide isolation in all three planes and in any orientation. The load-supporting capability of the WRI is identified from the static stiffness in the loading direction. Static stiffness mainly depends on the geometrical and material properties of the WRI. This study develops an analytical model for the static stiffness in the vertical direction by using Castigliano's second theorem. The model is validated by using the experimental results obtained from a series of monotonic loading tests. The flexural rigidity of the wire ropes required in the model is obtained from the transverse bending test. Then, the analytical model is used to conduct a parametric analysis on the effects of wire rope diameter, width, height, and number of turns (loops) on vertical stiffness. The wire rope diameter influences stiffness more than the other geometric parameters. The developed model can be accurately used for the evaluation and design of WRIs.

  5. Assessment the Relationship Between Parents' Literacy Level with Children Growth in Mashhad: An Analytic Descriptive Study

    Directory of Open Access Journals (Sweden)

    Masumeh Saeidi

    2013-12-01

    Full Text Available Introduction: Present children are the investments of community in the future. Preparing children health which leads to the stability of community health, provided to accurate implementation of educational and health programs in the community and especially in mothers. So it is necessary to determine the relationship between parents' literacy  with growth rate in children. Materials and Methods: This cross-sectional descriptive-analytic study was conducted on 300 mothers referring to 10 selected Mashhad health-care centers for monitoring their 6-24-month year old infants. They completed questionnaire. Participants were selected by cluster and simple random sampling. Data were analyzed by descriptive- analytic statistics and using SPSS 16. Results: Presentfindings showed a significant relationship between literacy  level of parents with child growth status, breast feeding rate, junk food consumption, referring to health care center for growth monitoring, the age of initiating supplementary nutrition, the use of oil and butter in baby food and rate of attending in educational classes. So that higher literacy  level of parents was associated with using more formula, less junk food, oil and butter in baby's food and more referring times to health care center for monitoring child growth, desirable growth, and  also initiating supplementary food more at the assigned time (p

  6. Assessment the Relationship between Parents' Literacy Level with Children Growth in Mashhad: An Analytic Descriptive Study

    Directory of Open Access Journals (Sweden)

    Bibi Leila Hoseini

    2014-04-01

    Full Text Available Introduction: Present children are the investments of community in the future. Preparing children health which leads to the stability of community health, provided to accurate implementation of educational and health programs in the community and especially in mothers. So it is necessary to determine the relationship between parents' literacy with growth rate in children.   Materials and Methods: This cross-sectional descriptive-analytic study was conducted on 300 mothers referring to 10 selected Mashhad health-care centers for monitoring their 6-24-month year old infants. They completed questionnaire. Participants were selected by cluster and simple random sampling. Data were analyzed by descriptive- analytic statistics and using SPSS 16.   Results: Presentfindings showed a significant relationship between literacy  level of parents with child growth status, breast feeding rate, junk food consumption, referring to health care center for growth monitoring, the age of initiating supplementary nutrition, the use of oil and butter in baby food and rate of attending in educational classes. So that higher literacy  level of parents was associated with using more formula, less junk food, oil and butter in baby's food and more referring times to health care center for monitoring child growth, desirable growth, and  also initiating supplementary food more at the assigned time (P

  7. 30 CFR 903.700 - Arizona Federal program.

    Science.gov (United States)

    2010-07-01

    ... Resources has jurisdiction over the mining of minerals, and oil and gas under Title 27 of the Arizona....700 Mineral Resources OFFICE OF SURFACE MINING RECLAMATION AND ENFORCEMENT, DEPARTMENT OF THE INTERIOR PROGRAMS FOR THE CONDUCT OF SURFACE MINING OPERATIONS WITHIN EACH STATE ARIZONA § 903.700 Arizona Federal...

  8. 75 FR 18145 - Eastern Arizona Counties Resource Advisory Committee

    Science.gov (United States)

    2010-04-09

    ... DEPARTMENT OF AGRICULTURE Forest Service Eastern Arizona Counties Resource Advisory Committee AGENCY: Forest Service, USDA. ACTION: Notice of meeting. SUMMARY: The Eastern Arizona Counties Resource... Rivera, Coordinator, Eastern Arizona Counties Resource Advisory Committee, c/o Forest Service, USDA, P.O...

  9. The Teacher's Role in Quality Classroom Interactions: Q&A with Dr. Drew Gitomer. REL Mid-Atlantic Teacher Effectiveness Webinar Series

    Science.gov (United States)

    Regional Educational Laboratory Mid-Atlantic, 2013

    2013-01-01

    In this webinar, Dr. Drew Gitomer, professor at Rutgers University, shared results from recent studies of classroom observations that helped participants understand both general findings about the qualities of classroom interactions and also the challenges to carrying out valid and reliable observations. This Q&A addressed the questions…

  10. Energy Fuels Nuclear, Inc. Arizona Strip Operations

    International Nuclear Information System (INIS)

    Pool, T.C.

    1993-01-01

    Founded in 1975 by uranium pioneer, Robert W. Adams, Energy Fuels Nuclear, Inc. (EFNI) emerged as the largest US uranium mining company by the mid-1980s. Confronting the challenges of declining uranium market prices and the development of high-grade ore bodies in Australia and Canada, EFNI aggressively pursued exploration and development of breccia-pipe ore bodies in Northwestern Arizona. As a result, EFNI's production for the Arizona Strip of 18.9 million pounds U 3 O 8 over the period 1980 through 1991, maintained the company's status as a leading US uranium producer

  11. Analytical and Experimental Study of Recycling Baffled Double-Pass Solar Air Heaters with Attached Fins

    Directory of Open Access Journals (Sweden)

    Chun Sheng Lin

    2013-03-01

    Full Text Available The study of the heat transfer of solar air heaters with a new design using an absorbing plate with fins and baffles, which facilitate the recycling of flowing air, is reported. The mathematical formulation and analytical analysis for such a recyclic baffled double-pass solar air heater were developed theoretically. The performance of the device was studied experimentally as well. The theoretical predicted and experimental results were compared with another design, i.e., a downward-type single-pass solar air heater without recycle and double-pass operations reported in our previous work. Significant improvement in heat-transfer efficiency is achieved with the baffle and fin design due to the recycling heating and the extended heat transfer area. The effects of mass flow rate and recycle ratio on the heat-transfer efficiency enhancement as well as on the power consumption increment are also discussed.

  12. Semi-analytical fluid study of the laser wake field excitation in the strong intensity regime

    Energy Technology Data Exchange (ETDEWEB)

    Jovanović, D., E-mail: djovanov@ipb.ac.rs [Institute of Physics, University of Belgrade, Belgrade (Serbia); Fedele, R., E-mail: renato.fedele@na.infn.it [Dipartimento di Fisica, Universitá di Napoli Federico II, Napoli (Italy); INFN Sezione di Napoli, Napoli (Italy); Belić, M., E-mail: milivoj.belic@qatar.tamu.edu [Texas A & M University at Qatar, Doha (Qatar); De Nicola, S., E-mail: sergio.denicola@spin.cnr.it [Dipartimento di Fisica, Universitá di Napoli Federico II, Napoli (Italy); INFN Sezione di Napoli, Napoli (Italy); CNR-SPIN, Complesso Universitario di Monte S' Angelo, Napoli (Italy)

    2016-09-01

    We present an analytical and numerical study of the interaction of a multi-petawatt, pancake-shaped laser pulse with an unmagnetized plasma. The study has been performed in the ultrarelativistic regime of electron jitter velocities, in which the plasma electrons are almost completely expelled from the pulse region. The calculations are applied to a laser wake field acceleration scheme with specifications that may be available in the next generation of Ti:Sa lasers and with the use of recently developed pulse compression techniques. A set of novel nonlinear equations is derived using a three-timescale description, with an intermediate timescale associated with the nonlinear phase of the electromagnetic wave and with the spatial bending of its wave front. They describe, on an equal footing, both the strong and the moderate laser intensity regimes, pertinent to the core and to the edges of the pulse.

  13. Experimental and analytical study of the bremsstrahlung radiation production at low energies

    International Nuclear Information System (INIS)

    Moran, P.; Gonzales, L.; Delgado, V.; Lopez, A.; Vano, E.

    1986-01-01

    The bremsstrahlung photon beam from an X-ray tube with chromium anode has been studied, for an electron energy of 60 Kev. In the experimental step, a new measurement method has been developed. This is based on the detection and measurement of the fluorescence produced when the photons from the tube impinge on targets which are used as calibrated flux monitors. The composition and physical characteristics of the targets are well-known. In the steps of experimental data treatment, an analytical study of the theoretical models describing thick target bremsstrahlung yield is performed. A factorization which accounts for the elemental physical processes is obtained, employing simple mathematical functions. The characteristic parameters found in the numerical fit process lead to results in good agreement with the experimental observations from other authors and predict theoretical exposure values in perfect agreement with the exposures measured for X-ray beams generated in several operating conditions. (author)

  14. Automating the Analytical Laboratories Section, Lewis Research Center, National Aeronautics and Space Administration: a feasibility study

    International Nuclear Information System (INIS)

    Boyle, W.G.; Barton, G.W.

    1979-01-01

    We studied the feasibility of computerized automation of the Analytical Laboratories Section at NASA's Lewis Research Center. Since that laboratory's duties are not routine, we set our automation goals with that in mind. We selected four instruments as the most likely automation candidates: an atomic absorption spectrophotometer, an emission spectrometer, an x-ray fluorescence spectrometer, and an x-ray diffraction unit. Our study describes two options for computer automation: a time-shared central computer and a system with microcomputers for each instrument connected to a central computer. A third option, presented for future planning, expands the microcomputer version. We determine costs and benefits for each option. We conclude that the microcomputer version best fits the goals and duties of the laboratory and that such an automated system is needed to meet the laboratory's future requirements

  15. Concept of a QA-programme for the recipient country, goals and measures

    International Nuclear Information System (INIS)

    Thomas, F.W.

    1986-04-01

    Ordering, design and erection of a NPP is a complex business even in a country with experience. Therefore a QA-Programme can be helpful to do the work in a planned and organized manner. In the case of a recipient country the use of administrative QA-measures seems to be a necessary support, especially for the ordering company. It is not the intention of the QA-Programme to say what to do, and so it cannot solve ''political'' questions of the business, but the QA-Programme can say how the work has to be done to bring it to a good end. This lecture points out the most important and interesting questions in the phase of establishing a QA-Programme. Examples of solutions are given. (author). 13 figs

  16. Applications of QA to RandD support of HLW programs

    International Nuclear Information System (INIS)

    Ryder, D.E.

    1988-05-01

    The application of a formal QA program to any discipline or organization can be difficult to achieve and to do so with a research and development organization has special challenges that are somewhat unique. This paper describes how a QA program based upon a national consensus standard (developed for application to the design, construction and operation of nuclear facilities) has been successfully applied to some of the research and development activities in support of the High Level Waste Programs. This description includes a discussion on the importance of being creative when interpreting the QA standard, a brief overview of the QA program that was developed and the results achieved during implementation of the QA program. 4 refs., 4 figs

  17. Symptoms of delirium: an exploratory factor analytic study among referred patients.

    Science.gov (United States)

    Jain, Gaurav; Chakrabarti, Subho; Kulhara, Parmanand

    2011-01-01

    Factor analytic studies of delirium symptoms among patients referred through consultation-liaison psychiatric services are rare. We examined the factor structure of delirium symptoms in referred patients and determined whether combining items from several delirium rating scales influenced the factor structure of delirium symptoms. Eighty-six patients with delirium (Diagnostic and Statistical Manual of Mental Disorders, Fourth Edition, Text Revision) referred though the consultation-liaison services were assessed with structured rating scales. Nineteen symptom items extracted from the Delirium Rating Scale-Revised-98 (DRS-R-98), the Memorial Delirium Assessment Scale and the Confusional State Evaluation Scale were subjected to an exploratory (principal component) factor analysis. A second such analysis was conducted on 15 items of the DRS-R-98 for comparison. Compared with prior studies, patients were younger and the majority had hyperactive delirium. Principal components analysis identified two factors: (1) a "cognitive" factor comprising of disturbances in language, thought processes, orientation, attention, short- and long-term memory, visuospatial ability, consciousness (awareness) and perseveration accounted for 28.9% of the variance and (2) a "behavioral" factor consisting of sleep-wake cycle disturbances, delusions, perceptual disturbances, motor agitation, affect-lability, distractibility, irritability and temporal onset accounted for 18.9% of the variance. An identical factor structure was obtained with the DRS-R-98 items. Similar to previous factor analytic studies, the present study supported the existence of two principal dimensions of delirium, cognitive and behavioral. Additionally, it extended the results of earlier investigations to a wider group of patients with delirium, suggesting that these dimensions might provide important clues to the neurobiology of delirium. Copyright © 2011 Elsevier Inc. All rights reserved.

  18. Water-Rights Settlements and Reclamation in Central Arizona as a Cross-Cultural Experience: A Reexamination of Native Water Policy

    Science.gov (United States)

    Matsui, Kenichi

    2011-01-01

    As of December 2010, the US Congress had enacted more than twenty major community-specific Native water-rights settlements, and the state of Arizona had more of these settlements (eight) than any other US state. This unique situation has invited voluminous studies on Arizona's Native water-rights settlements. Although these studies have clarified…

  19. Feasibility of digital footprint data for health analytics and services: an explorative pilot study.

    Science.gov (United States)

    Harjumaa, Marja; Saraniemi, Saila; Pekkarinen, Saara; Lappi, Minna; Similä, Heidi; Isomursu, Minna

    2016-11-09

    As a result of digitalization, data is available about almost every aspect of our lives. Personal data collected by individuals themselves or stored by organizations interacting with people is known as a digital footprint. The purpose of this study was to identify prerequisites for collecting and using digital data that could be valuable for health data analytics and new health services. Researchers and their contacts involved in a nationwide research project focusing on digital health in Finland were asked to participate in a pilot study on collecting their own personal data from various organizations of their own choice, such as retail chains, banks, insurance companies, and healthcare providers. After the pilot, a qualitative inquiry was adopted to collect semi-structured interview data from twelve active participants in the pilot. Interviews comprised themes such as the experiences of collecting personal data, as well as the usefulness of the data in general and for the participants themselves. Interview data was then analyzed thematically. Even if the participants had an academic background and were highly motivated to collect and use their data, they faced many challenges, such as quite long delays in the provision of the data, and the unresponsiveness of some organizations. Regarding the usefulness of the acquired personal data, our results show that participants had high expectations, but they were disappointed with the small amount of data and its irrelevant content. For the most part, the data was not in a format that would be useful for health data analytics and new health services. Participants also found that there were actual mistakes in their health data reports. The study revealed that collecting and using digital footprint data, even by knowledgeable individuals, is not an easy task. As the usefulness of the acquired personal health data mainly depended on its form and usability for services or solutions relevant to an individual, rather than on

  20. Electro-Analytical Study of Material Interfaces Relevant for Chemical Mechanical Planarization and Lithium Ion Batteries

    Science.gov (United States)

    Turk, Michael C.

    This dissertation work involves two areas of experimental research, focusing specifically on the applications of electro-analytical techniques for interfacial material characterization. The first area of the work is centered on the evaluation and characterization of material components used for chemical mechanical planarization (CMP) in the fabrication of semiconductor devices. This part also represents the bulk of the projects undertaken for the present dissertation. The other area of research included here involves exploratory electrochemical studies of certain electrolyte and electrode materials for applications in the development of advanced lithium ion secondary batteries. The common element between the two areas of investigation is the technical approach that combines a broad variety of electro-analytical characterization techniques to examine application specific functions of the associated materials and devices. The CMP related projects concentrate on designing and evaluating materials for CMP slurries that would be useful in the processing of copper interconnects for the sub-22 nm technology node. Specifically, ruthenium and cobalt are nontraditional barrier materials currently considered for the new interconnects. The CMP schemes used to process the structures based on these metals involve complex surface chemistries of Ru, Co and Cu (used for wiring lines). The strict requirement of defect-control while maintaining material removal by precisely regulated tribo-corrosion complicates the designs of the CMP slurries needed to process these systems. Since Ru is electrochemically more noble than Cu, the surface regions of Cu assembled in contact with Ru tend to generate defects due to galvanic corrosion in the CMP environment. At the same time, Co is strongly reactive in the typical slurry environment and is prone to developing galvanic corrosion induced by Cu. The present work explores a selected class of alkaline slurry formulations aimed at reducing these

  1. Lower Colorado River GRP Dams and Water Retention Structures, Arizona, 2012, Arizona Department of Environmental Quality

    Data.gov (United States)

    U.S. Environmental Protection Agency — Location of dams and water retention structures as compiled from multiple sources by the Arizona Department of Environmental Quality (ADEQ). The data are "sensitive"...

  2. Analytical and computational study of magnetization switching in kinetic Ising systems with demagnetizing fields

    DEFF Research Database (Denmark)

    Richards, H.L.; Rikvold, P.A.

    1996-01-01

    particularly promising as materials for high-density magnetic recording media. In this paper we use analytic arguments and Monte Carlo simulations to quantitatively study the effects of the demagnetizing field on the dynamics of magnetization switching in two-dimensional, single-domain, kinetic Ising systems....... For systems in the weak-field ''stochastic region,'' where magnetization switching is on average effected by the nucleation and growth of a single droplet, the simulation results can be explained by a simple model in which the free energy is a function only of magnetization. In the intermediate......-field ''multidroplet region,'' a generalization of Avrami's law involving a magnetization-dependent effective magnetic field gives good agreement with the simulations. The effects of the demagnetizing field do not qualitatively change the droplet-theoretical picture of magnetization switching in highly anisotropic...

  3. An analytical study of physical models with inherited temporal and spatial memory

    Science.gov (United States)

    Jaradat, Imad; Alquran, Marwan; Al-Khaled, Kamel

    2018-04-01

    Du et al. (Sci. Reb. 3, 3431 (2013)) demonstrated that the fractional derivative order can be physically interpreted as a memory index by fitting the test data of memory phenomena. The aim of this work is to study analytically the joint effect of the memory index on time and space coordinates simultaneously. For this purpose, we introduce a novel bivariate fractional power series expansion that is accompanied by twofold fractional derivatives ordering α, β\\in(0,1]. Further, some convergence criteria concerning our expansion are presented and an analog of the well-known bivariate Taylor's formula in the sense of mixed fractional derivatives is obtained. Finally, in order to show the functionality and efficiency of this expansion, we employ the corresponding Taylor's series method to obtain closed-form solutions of various physical models with inherited time and space memory.

  4. Heuristic and analytic processes in reasoning: an event-related potential study of belief bias.

    Science.gov (United States)

    Banks, Adrian P; Hope, Christopher

    2014-03-01

    Human reasoning involves both heuristic and analytic processes. This study of belief bias in relational reasoning investigated whether the two processes occur serially or in parallel. Participants evaluated the validity of problems in which the conclusions were either logically valid or invalid and either believable or unbelievable. Problems in which the conclusions presented a conflict between the logically valid response and the believable response elicited a more positive P3 than problems in which there was no conflict. This shows that P3 is influenced by the interaction of belief and logic rather than either of these factors on its own. These findings indicate that belief and logic influence reasoning at the same time, supporting models in which belief-based and logical evaluations occur in parallel but not theories in which belief-based heuristic evaluations precede logical analysis.

  5. Evaluating the NOx Storage Catalysts (NSC Aging: A Preliminary Analytical Study with Electronic Microscopy

    Directory of Open Access Journals (Sweden)

    Leonarda Bellebuono

    2017-10-01

    Full Text Available This paper describes an expeditious and reliable method for determining the thermal effects in a static condition of commercial NOx storage catalysts (NSCs using scanning electron microscopy with an energy dispersive X-ray analytical system (SEM/EDS. It is worth remarking that possible changes in the morphology and in the elemental composition of the catalyst may be considered as the most important causes of the lower conversion of NOx. The information attained in this work indicates that Pt nanoparticle sintering is strongly increased by the oxygen exposure, and this can be considered a very useful preliminary investigation for the studies already present in the literature on the efficiency of NSCs.

  6. D.E.M.T. Experimental and analytical studies on seismic isolation

    International Nuclear Information System (INIS)

    Gantenbein, F.; Buland, P.

    1989-01-01

    The various studies which have been performed in C.E.A./D.E.M.T. will be reviewed in the paper. They are experimental or theoretical and related to the overall behavior of isolated structures. Among the experimental work one can notice: - the seismic tests on a shaking table of a concrete cylinder isolated by sliding neoprene pads, - the vibrational tests on the reaction mass of TAMARIS seismic facility. The analytical work consists of dynamic calculation method development: - for the soil structure interaction in case of pads interposed between an upper raft and pedestals; - for the time history calculation of sliding structures; - for fluid structure interaction (coupling of fluid and structure motion or sloshing modes). Finally comments will be given on the seismic isolation consequencies for the analysis of F.B.R. vessels: the modes can no more be considered independent (SRSS method leads to important errors), the sloshing increases

  7. Analytical Study on the Beyond Design Seismic Capacity of Reinforced Concrete Shear Walls

    Energy Technology Data Exchange (ETDEWEB)

    Nugroho, Tino Sawaldi Adi [Korea Advanced Institute of Science and Technology, Daejeon (Korea, Republic of); Chi, Ho-Seok [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

    2015-10-15

    The OECD-NEA has organized an international benchmarking program to better understand this critical issue. The benchmark program provides test specimen geometry, test setup, material properties, loading conditions, recorded measures, and observations of the test specimens. The main objective of this research is to assess the beyond design seismic capacity of the reinforced concrete shear walls tested at the European Laboratory for Structural Assessment between 1997 and 1998 through participation in the OECD-NEA benchmark program. In this study, assessing the beyond design seismic capacity of reinforced concrete shear walls is performed analytically by comparing numerical results with experimental results. The seismic shear capacity of the reinforced concrete shear wall was predicted reasonably well using ABAQUS program. However, the proper calibration of the concrete material model was necessary for better prediction of the behavior of the reinforced concrete shear walls since the response was influenced significantly by the material constitutive model.

  8. The interior of axisymmetric and stationary black holes: Numerical and analytical studies

    International Nuclear Information System (INIS)

    Ansorg, Marcus; Hennig, Joerg

    2011-01-01

    We investigate the interior hyperbolic region of axisymmetric and stationary black holes surrounded by a matter distribution. First, we treat the corresponding initial value problem of the hyperbolic Einstein equations numerically in terms of a single-domain fully pseudo-spectral scheme. Thereafter, a rigorous mathematical approach is given, in which soliton methods are utilized to derive an explicit relation between the event horizon and an inner Cauchy horizon. This horizon arises as the boundary of the future domain of dependence of the event horizon. Our numerical studies provide strong evidence for the validity of the universal relation A + A - (8πJ) 2 where A + and A - are the areas of event and inner Cauchy horizon respectively, and J denotes the angular momentum. With our analytical considerations we are able to prove this relation rigorously.

  9. Latent structure of the Wisconsin Card Sorting Test: a confirmatory factor analytic study.

    Science.gov (United States)

    Greve, Kevin W; Stickle, Timothy R; Love, Jeffrey M; Bianchini, Kevin J; Stanford, Matthew S

    2005-05-01

    The present study represents the first large scale confirmatory factor analysis of the Wisconsin Card Sorting Test (WCST). The results generally support the three factor solutions reported in the exploratory factor analysis literature. However, only the first factor, which reflects general executive functioning, is statistically sound. The secondary factors, while likely reflecting meaningful cognitive abilities, are less stable except when all subjects complete all 128 cards. It is likely that having two discontinuation rules for the WCST has contributed to the varied factor analytic solutions reported in the literature and early discontinuation may result in some loss of useful information. Continued multivariate research will be necessary to better clarify the processes underlying WCST performance and their relationships to one another.

  10. Stress control in electrodeposited CoFe films—Experimental study and analytical model

    International Nuclear Information System (INIS)

    Brankovic, Stanko R.; Kagajwala, Burhanuddin; George, Jinnie; Majkic, Goran; Stafford, Gery; Ruchhoeft, Paul

    2012-01-01

    Work investigating the effect of saccharin as an additive on growth stress and structure of electrodeposited CoFe films is presented. The saccharin concentrations were in the range between 0 g L −1 and 1.5 g L −1 . The stress measurements are performed in situ during electrodeposition of CoFe films using cantilever-bending method (curvature measurements). The structure of CoFe films was studied by transmission electron microscopy and X-ray diffraction. Results show that growth stress is a decreasing function of saccharin concentration. No appreciable change in composition, grain size, orientation or texture of CoFe films are observed with increasing saccharin content in solution. The growth stress dependence on saccharin concentration is discussed within the framework of analytical model, which directly links the observed stress decrease with the apparent saccharin coverage of the CoFe film surface during the electrodeposition process.

  11. A visual analytics design for studying rhythm patterns from human daily movement data

    Directory of Open Access Journals (Sweden)

    Wei Zeng

    2017-06-01

    Full Text Available Human’s daily movements exhibit high regularity in a space–time context that typically forms circadian rhythms. Understanding the rhythms for human daily movements is of high interest to a variety of parties from urban planners, transportation analysts, to business strategists. In this paper, we present an interactive visual analytics design for understanding and utilizing data collected from tracking human’s movements. The resulting system identifies and visually presents frequent human movement rhythms to support interactive exploration and analysis of the data over space and time. Case studies using real-world human movement data, including massive urban public transportation data in Singapore and the MIT reality mining dataset, and interviews with transportation researches were conducted to demonstrate the effectiveness and usefulness of our system.

  12. Experimental and analytical studies on waterhammer generated by the closing of check valves

    International Nuclear Information System (INIS)

    Huet, J.L.; Garcia, J.L.; Coppolani, P.; Ziegler, B.

    1987-01-01

    A double-guillotine rupture on a water line upstream from a check valve generates a severe transient between the check valve and the pressure vessel on the downstream side. Successively following phenomena occur: - decrease then reversal of the flow, - closing of the check valve with impact of the plug on its seat, - waterhammer propagating in the pipe downstream from the check valve. The COMMISARIAT A L'ENERGIE ATOMIQUE (C.E.A.) FRAMATOME and ELECTRICITE DE FRANCE (E.D.F.) have undertaken a joint program in order to: - investigate the behavior uf the check valve in the event of a sudden closure, - evaluate the pressure and flow transient in the line. The program includes: - full scale tests in two loops, CLAUDIA (C.E.A.) and ECLAIR (E.D.F.), - analytical studies in order to qualify the calculation codes. This paper describes the experimental program and presents the analysis results for a benchmark test

  13. Analytical and numerical studies of positive ion beam expansion for surface treatment applications

    Science.gov (United States)

    Lounes-Mahloul, Soumya; Bendib, Abderrezeg; Oudini, Noureddine

    2018-01-01

    The aim of this work is to study the expansion in vacuum, of a positive ion beam with the use of one dimensional (1D) analytic model and a two dimensional Particle-In-Cell (2D-PIC) simulation. The ion beam is extracted and accelerated from preformed plasma by an extraction system composed of two polarized parallel perforated grids. The results obtained with both approaches reveal the presence of a potential barrier downstream the extraction system which tends to reflect the ion flux. The dependence of the critical distance for which all extracted ions are reflected, is investigated as a function of the extracted ion beam current density. In particular, it is shown that the 1D model recovers the well-known Child-Langmuir law and that the 2D simulation presents a significant discrepancy with respect to the 1D prediction. Indeed, for a given value of current density, the transverse effects lead to a greater critical distance.

  14. Comparative aseismic response study of different analytical models of nuclear power plant

    International Nuclear Information System (INIS)

    Takemori, T.; Ogiwara, Y.; Kawakatsu, T.; Abe, Y.; Kitade, K.

    1977-01-01

    This study consists of two major sections; one is comparison of magnification factor of input acceleration between finite model and spring-mass model, the other is evaluation of modified spring-mass models for aseismic design of nuclear power plant. The structure model used in this study is a P.W.R. reactor containment building composed of the outer shield wall, the steel containment and the internal structure. The rigidity of the foundation rock is represented by shear wave velocity Vs. The magnification of bedrock acceleration at the structure foundation, main floors and free surface of foundation rock are calculated using axisymmetric finite element analytical model with various rock rigidities. The outer shield wall and the steel containment are represented by shell elements, and the internal structure and foundation rock are represented by quadrilateral elements. Each nodal point has four degrees of freedom, in shell element, and three in quadrilateral element. The total degrees of this analytical model are large, so the eigenvalue is calculated by the subspace iterative method. The responses are calculated by time history of acceleration and response spectrum based on the mode superposition method. The spring-mass model is most used in aseismic design for its simplicity. But, if the foundation rock spring is calculated assuming the semi-infinite elastic solid, the analyses of the magnification of acceleration in foundation rock are limited. From the calculated results of the F.E.M. model, the modification of the spring-mass model is estimated, considering the magnification ratio of foundation rock beneath the structure

  15. Plastic deformation of crystals: analytical and computer simulation studies of dislocation glide

    International Nuclear Information System (INIS)

    Altintas, S.

    1978-05-01

    The plastic deformation of crystals is usually accomplished through the motion of dislocations. The glide of a dislocation is impelled by the applied stress and opposed by microstructural defects such as point defects, voids, precipitates and other dislocations. The planar glide of a dislocation through randomly distributed obstacles is considered. The objective of the present research work is to calculate the critical resolved shear stress (CRSS) for athermal glide and the velocity of the dislocation at finite temperature as a function of the applied stress and the nature and strength of the obstacles. Dislocation glide through mixtures of obstacles has been studied analytically and by computer simulation. Arrays containing two kinds of obstacles as well as square distribution of obstacle strengths are considered. The critical resolved shear stress for an array containing obstacles with a given distribution of strengths is calculated using the sum of the quadratic mean of the stresses for the individual obstacles and is found to be in good agreement with the computer simulation data. Computer simulation of dislocation glide through randomly distributed obstacles containing up to 10 6 obstacles show that the CRSS decreases as the size of the array increases and approaches a limiting value. Histograms of forces and of segment lengths are obtained and compared with theoretical predictions. Effects of array shape and boundary conditions on the dislocation glide are also studied. Analytical and computer simulation results are compared with experimental results obtained on precipitation-, irradiation-, forest-, and impurity cluster-hardening systems and are found to be in good agreement

  16. Analytical electron microscope study of the omega phase transformation in a zirconium--niobium alloy

    Energy Technology Data Exchange (ETDEWEB)

    Zaluzec, N.J.

    1979-06-01

    An in-situ study of the as-quenched omega phase transformation in Zr--15% Nb was conducted between the temperatures of 77 and 300/sup 0/K using analytical electron microscopy. The domain size of the omega regions observed in this investigation was on the order of 30 A, consistent with previous observations in this system. No alignment of omega domains along <222> directions of the bcc lattice was observed and in-situ thermal cycling experiments failed to produce a long period structure of alternating ..beta.. and ..omega.. phase regions as predicted by one theory of this transformation. Several techniques of microstructural analysis were developed, refined, and standardized. Grouped under the general classification of Analytical Electron Microscopy (AEM) they provide the experimentalist with a unique tool for the microcharacterization of solids, allowing semiquantitative to quantitative analysis of the morphology, crystallography, elemental composition, and electronic structure of regions as small as 20 A in diameter. These techniques have complications, and it was necessary to study the AEM system used in this work so that instrumental artifacts which invalidate the information produced in the microscope environment might be eliminated. Once these factors had been corrected, it was possible to obtain a wealth of information about the microvolume of material under investigation. The microanalytical techniques employed during this research include: energy dispersive x-ray spectroscopy (EDS) using both conventional and scanning transmission electron microscopy (CTEM, STEM), transmission scanning electron diffraction (TSED), the stationary diffraction pattern technique, and electron energy loss spectroscopy (ELS) using a dedicated scanning transmission electron microscope (DSTEM).

  17. Plastic deformation of crystals: analytical and computer simulation studies of dislocation glide

    Energy Technology Data Exchange (ETDEWEB)

    Altintas, S.

    1978-05-01

    The plastic deformation of crystals is usually accomplished through the motion of dislocations. The glide of a dislocation is impelled by the applied stress and opposed by microstructural defects such as point defects, voids, precipitates and other dislocations. The planar glide of a dislocation through randomly distributed obstacles is considered. The objective of the present research work is to calculate the critical resolved shear stress (CRSS) for athermal glide and the velocity of the dislocation at finite temperature as a function of the applied stress and the nature and strength of the obstacles. Dislocation glide through mixtures of obstacles has been studied analytically and by computer simulation. Arrays containing two kinds of obstacles as well as square distribution of obstacle strengths are considered. The critical resolved shear stress for an array containing obstacles with a given distribution of strengths is calculated using the sum of the quadratic mean of the stresses for the individual obstacles and is found to be in good agreement with the computer simulation data. Computer simulation of dislocation glide through randomly distributed obstacles containing up to 10/sup 6/ obstacles show that the CRSS decreases as the size of the array increases and approaches a limiting value. Histograms of forces and of segment lengths are obtained and compared with theoretical predictions. Effects of array shape and boundary conditions on the dislocation glide are also studied. Analytical and computer simulation results are compared with experimental results obtained on precipitation-, irradiation-, forest-, and impurity cluster-hardening systems and are found to be in good agreement.

  18. Analytical electron microscope study of the omega phase transformation in a zirconium--niobium alloy

    International Nuclear Information System (INIS)

    Zaluzec, N.J.

    1979-06-01

    An in-situ study of the as-quenched omega phase transformation in Zr--15% Nb was conducted between the temperatures of 77 and 300 0 K using analytical electron microscopy. The domain size of the omega regions observed in this investigation was on the order of 30 A, consistent with previous observations in this system. No alignment of omega domains along directions of the bcc lattice was observed and in-situ thermal cycling experiments failed to produce a long period structure of alternating β and ω phase regions as predicted by one theory of this transformation. Several techniques of microstructural analysis were developed, refined, and standardized. Grouped under the general classification of Analytical Electron Microscopy (AEM) they provide the experimentalist with a unique tool for the microcharacterization of solids, allowing semiquantitative to quantitative analysis of the morphology, crystallography, elemental composition, and electronic structure of regions as small as 20 A in diameter. These techniques have complications, and it was necessary to study the AEM system used in this work so that instrumental artifacts which invalidate the information produced in the microscope environment might be eliminated. Once these factors had been corrected, it was possible to obtain a wealth of information about the microvolume of material under investigation. The microanalytical techniques employed during this research include: energy dispersive x-ray spectroscopy (EDS) using both conventional and scanning transmission electron microscopy (CTEM, STEM), transmission scanning electron diffraction (TSED), the stationary diffraction pattern technique, and electron energy loss spectroscopy (ELS) using a dedicated scanning transmission electron microscope

  19. Development and Validation of a Learning Analytics Framework: Two Case Studies Using Support Vector Machines

    Science.gov (United States)

    Ifenthaler, Dirk; Widanapathirana, Chathuranga

    2014-01-01

    Interest in collecting and mining large sets of educational data on student background and performance to conduct research on learning and instruction has developed as an area generally referred to as learning analytics. Higher education leaders are recognizing the value of learning analytics for improving not only learning and teaching but also…

  20. Factors Influencing Beliefs for Adoption of a Learning Analytics Tool: An Empirical Study

    Science.gov (United States)

    Ali, Liaqat; Asadi, Mohsen; Gasevic, Dragan; Jovanovic, Jelena; Hatala, Marek

    2013-01-01

    Present research and development offer various learning analytics tools providing insights into different aspects of learning processes. Adoption of a specific tool for practice is based on how its learning analytics are perceived by educators to support their pedagogical and organizational goals. In this paper, we propose and empirically validate…

  1. Setting analytical performance specifications based on outcome studies - is it possible?

    NARCIS (Netherlands)

    Horvath, Andrea Rita; Bossuyt, Patrick M. M.; Sandberg, Sverre; John, Andrew St; Monaghan, Phillip J.; Verhagen-Kamerbeek, Wilma D. J.; Lennartz, Lieselotte; Cobbaert, Christa M.; Ebert, Christoph; Lord, Sarah J.

    2015-01-01

    The 1st Strategic Conference of the European Federation of Clinical Chemistry and Laboratory Medicine proposed a simplified hierarchy for setting analytical performance specifications (APS). The top two levels of the 1999 Stockholm hierarchy, i.e., evaluation of the effect of analytical performance

  2. Laboratory QA/QC improvements for small drinking water systems at Savannah River Site

    Energy Technology Data Exchange (ETDEWEB)

    Turner, R.D.

    1995-12-01

    The Savannah River Site (SRS), a 310 square mile facility located near Aiken, S.C., is operated by Westinghouse Savannah River Company for the US Department of Energy. SRS has 28 separate drinking water systems with average daily demands ranging from 0.0002 to 0.5 MGD. All systems utilize treated groundwater. Until recently, the water laboratories for each system operated independently. As a result, equipment, reagents, chemicals, procedures, personnel, and quality control practices differed from location to location. Due to this inconsistency, and a lack of extensive laboratory OA/QC practices at some locations, SRS auditors were not confident in the accuracy of daily water quality analyses results. The Site`s Water Services Department addressed these concerns by developing and implementing a practical laboratory QA/QC program. Basic changes were made which can be readily adopted by most small drinking water systems. Key features of the program include: Standardized and upgraded laboratory instrumentation and equipment; standardized analytical procedures based on vendor manuals and site requirements; periodic accuracy checks for all instrumentation; creation of a centralized laboratory to perform metals digestions and chlorine colorimeter accuracy checks; off-site and on-site operator training; proper storage, inventory and shelf life monitoring for reagents and chemicals. This program has enhanced the credibility and accuracy of SRS drinking water system analyses results.

  3. Arizona Public Library Statistics, 2000-2001.

    Science.gov (United States)

    Elliott, Jan, Comp.

    These statistics were compiled from information supplied by Arizona's public libraries. The document is divided according to the following county groups: Apache, Cochise; Coconino, Gila; Graham, Greenlee, La Paz; Maricopa; Mohave, Navajo; Pima, Pinal; Santa Cruz, Yavapai; and Yuma. Statistics are presented on the following: general information;…

  4. Arizona Public Library Statistics. 1994-1995.

    Science.gov (United States)

    Arizona State Dept. of Library and Archives, Phoenix.

    The statistics in this document were provided by Arizona public libraries for 1994-95. The counties are grouped as follows: Apache, Cochise,and Coconino; Gila, Graham, Greenlee, and La Paz; Maricopa and Mohave; Navajo, Pima, and Pinal; and Santa Cruz, Yavapai, and Yuma. The following data is presented in table form for each of the five groups: (1)…

  5. Arizona Public Library Statistics, 1999-2000.

    Science.gov (United States)

    Arizona State Dept. of Library, Archives and Public Records, Phoenix.

    These statistics were compiled from information supplied by Arizona's public libraries. The document is divided according to the following county groups: Apache, Cochise; Coconino, Gila; Graham, Greenlee, La Paz; Maricopa; Mohave, Navajo; Pima, Pinal; Santa Cruz, Yavapai; Yuma. Statistics are presented on the following: general information;…

  6. Arizona Public Library Statistics, 1995-1996.

    Science.gov (United States)

    Arizona State Dept. of Library, Archives and Public Records, Phoenix.

    The statistics in this document were provided by Arizona public libraries for 1995-96. The counties are grouped as follows: Apache, Cochise, and Coconino; Gila, Graham, Greenlee, and La Paz; Maricopa and Mohave; Navajo, Pima, and Pinal; and Santa Cruz, Yavapai, and Yuma. The following data is presented in table form for each of the five groups:…

  7. Arizona's Forgotten Children: Promises To Keep.

    Science.gov (United States)

    Children's Action Alliance, Phoenix, AZ.

    This report provides an Arizona perspective on the implications and effects of homelessness on children and youth, whether they live with their families or on their own. Statistics on homeless families are provided, and issues affecting homeless families are discussed. These issues involve shelters, child care, education, and health. Issues that…

  8. Coccidiodomycosis in Arizona 2007-2008

    Centers for Disease Control (CDC) Podcasts

    2010-10-13

    This podcast looks at the impact of Coccidioidomycosis, or Valley Fever, in Arizona in 2007 and early 2008. CDC epidemiologist Dr. Tom Chiller discusses what researchers learned about this fungal disease.  Created: 10/13/2010 by National Center for Emerging and Zoonotic Infectious Diseases (NCEZID).   Date Released: 10/27/2010.

  9. 50 CFR 32.22 - Arizona.

    Science.gov (United States)

    2010-10-01

    ... of the State quail season. C. Big Game Hunting. We allow hunting of desert bighorn sheep in Arizona... the refuge from June 1 through August 19. C. Big Game Hunting. We allow hunting of mule and white... regulations subject to the following conditions: 1. You may only hunt feral hog during big game seasons. Each...

  10. Introduction to the Arizona Sky Island Arthropod Project (ASAP): Systematics, biogeography, ecology, and population genetics of arthropods of the Madrean Sky Islands

    Science.gov (United States)

    Wendy Moore; Wallace M. Meyer; Jeffrey A. Eble; Kimberly Franklin; John F. Wiens; Richard C. Brusca

    2013-01-01

    The Arizona Sky Island Arthropod Project (ASAP) is a new multi-disciplinary research program at the University of Arizona that combines systematics, biogeography, ecology, and population genetics to study origins and patterns of arthropod diversity along elevation gradients and among mountain ranges in the Madrean Sky Island Region. Arthropods represent taxonomically...

  11. Analytical methodology for the study of decontamination factors in mixer-settlers

    International Nuclear Information System (INIS)

    Alzabet, Horacio; Crubellati, Ricardo; Di Santo, Norberto; Eppis, Maria; Gonzalez, Guillermo; Bof, Elba; Devida, Claudio

    1987-01-01

    Due to the complexity of the samples, the choice of the analytical methodology to be applied at a radiochemical laboratory, for the evaluation of different separation steps if of a great importance. It is necessary to know the performance of mixer-settlers in two extreme situations: efficiency limit determined by fluid dynamic factors and separation factor determined by physicochemical variables. The element used to determine the efficiency limit was magnesium, due to its low distribution coefficient in tri-n-butyl phosphate (TBP). Zirconium, being one of the principal fission product, is partially extracted and was used to study the influence of chemical conditions. Atomic absorption spectrometry was selected for the determination of micro quantities of magnesium, and complexometry for macro quantities of this element. It was necessary to separate uranium using extraction chromatography with Kel F-TBP columns. Concentration range was 0.1 - 1 mg/L and 7 - 70 g/L respectively. Zirconium was determined by spectrophotometry with xylenol orange. For organic samples, it was necessary to reextract the analyte with fluoride, to evaporate with sulfuric acid and to complex the excess of fluoride with aluminum. Uranium determinations, required for mass balance, were carried out by spectrophotometry and potentiometry depending upon concentration. Because of the presence of zirconium, two methods were developed for uranium determination using liquid-liquid extraction in the presence of complexing agents. In one case, TBP was used as extractant, dibenzoylmethane as chromogenic reagent and EDTA as complexing agent. For very low quantities of uranium, tri-octyl phosphine oxide (TOPO) was the extractant, 2-(2-thiazolylazo)-5-diethylaminophenol (TAAP) the chromogenic reagent, and (1-2-cyclohexylenedinitrilo) tetraacetic acid (CDTA) the complexing agent. (Author)

  12. New analytical techniques for traffic management on the basis of system studies in logistics

    Directory of Open Access Journals (Sweden)

    Олександр Павлович Кіркін

    2017-07-01

    Full Text Available In today's market conditions, it is necessary for enterprises to constantly maintain their competitiveness. This is achieved through raising customer service standards and use of the latest management techniques. In most cases, enterprises adhere to the logistic principles to optimize production. Over time, however, the development of logistics resulted in emergence of its principal subdivisions: transport, storage, etc. Thus, nowadays there are several parallel methodological developments in the field of logistics and making up logistics chains and systems at different stages of the life cycle of the goods. System research in the field of warehouse logistics showed that the majority of its analytical models of management are based on task conflict. Similar tasks of managing traffic flows in transport logistics are solved by methods of SMO, graph theory, linear programming and differential equations of state etc. These methods are not more accurate than the methods of warehouse logistics, have similar important assumptions and simplifications, and require appropriate mathematical training and knowledge in the field of transport, and sometimes lack visible correlation with economic performance. New analytical techniques for the management of transportation systems based on task conflict will reduce the time and resources for optimization and finding solutions. Methods of warehousing logistics can only be used for the continuous transport quantities (intensity, speed, performance, capacity, execution of works, etc.. In the static condition the search for the optimal service intensity can be found in warehouse logistics. In the study of object in dynamics it is better to use transport approach. Some problems such as supplement of warehouse logistics models with elements of the transport task, are still to be decided

  13. A generic analytical foot rollover model for predicting translational ankle kinematics in gait simulation studies.

    Science.gov (United States)

    Ren, Lei; Howard, David; Ren, Luquan; Nester, Chris; Tian, Limei

    2010-01-19

    The objective of this paper is to develop an analytical framework to representing the ankle-foot kinematics by modelling the foot as a rollover rocker, which cannot only be used as a generic tool for general gait simulation but also allows for case-specific modelling if required. Previously, the rollover models used in gait simulation have often been based on specific functions that have usually been of a simple form. In contrast, the analytical model described here is in a general form that the effective foot rollover shape can be represented by any polar function rho=rho(phi). Furthermore, a normalized generic foot rollover model has been established based on a normative foot rollover shape dataset of 12 normal healthy subjects. To evaluate model accuracy, the predicted ankle motions and the centre of pressure (CoP) were compared with measurement data for both subject-specific and general cases. The results demonstrated that the ankle joint motions in both vertical and horizontal directions (relative RMSE approximately 10%) and CoP (relative RMSE approximately 15% for most of the subjects) are accurately predicted over most of the stance phase (from 10% to 90% of stance). However, we found that the foot cannot be very accurately represented by a rollover model just after heel strike (HS) and just before toe off (TO), probably due to shear deformation of foot plantar tissues (ankle motion can occur without any foot rotation). The proposed foot rollover model can be used in both inverse and forward dynamics gait simulation studies and may also find applications in rehabilitation engineering. Copyright 2009 Elsevier Ltd. All rights reserved.

  14. High-Risk Populations: The Pimas of Arizona and Mexico.

    Science.gov (United States)

    Schulz, Leslie O; Chaudhari, Lisa S

    2015-03-01

    The purpose of this review is first, to broadly summarize the long-term commitment that began in 1965 to studying type 2 diabetes and obesity through the cooperation of the Pima Indians of Arizona, and second, to discuss the investigations with the Pima Indians of Mexico that started in 1991. The later studies emphasize gene-environment interactions in the pathogenesis of these metabolic disorders. Through the participation of both groups of Pimas, the researchers made key findings with regard to the epidemiology, physiology, clinical assessment and genetics of type 2 diabetes and obesity.

  15. Action Video Game Training for Healthy Adults: A Meta-Analytic Study.

    Science.gov (United States)

    Wang, Ping; Liu, Han-Hui; Zhu, Xing-Ting; Meng, Tian; Li, Hui-Jie; Zuo, Xi-Nian

    2016-01-01

    Action video game (AVG) has attracted increasing attention from both the public and from researchers. More and more studies found video game training improved a variety of cognitive functions. However, it remains controversial whether healthy adults can benefit from AVG training, and whether young and older adults benefit similarly from AVG training. In the present study, we aimed to quantitatively assess the AVG training effect on the cognitive ability of adults and to compare the training effects on young and older adults by conducting a meta-analysis on previous findings. We systematically searched video game training studies published between January 1986 and July 2015. Twenty studies were included in the present meta-analysis, for a total of 313 participants included in the training group and 323 participants in the control group. The results demonstrate that healthy adults achieve moderate benefit from AVG training in overall cognitive ability and moderate to small benefit in specific cognitive domains. In contrast, young adults gain more benefits from AVG training than older adults in both overall cognition and specific cognitive domains. Age, education, and some methodological factors, such as the session duration, session number, total training duration, and control group type, modulated the training effects. These meta-analytic findings provide evidence that AVG training may serve as an efficient way to improve the cognitive performance of healthy adults. We also discussed several directions for future AVG training studies.

  16. Analysis of those national analytic epidemiological studies that by obtention the exposure-response functions

    International Nuclear Information System (INIS)

    Molina, E.; Meneses, E.

    2003-01-01

    The Impact Pathway methodology, developed in the frame of Extern E project for estimating of the external costs or externalities of the energy use, has as one of their main steps the health impact evaluation. This evaluation is carried out through exposure-response functions. In previous estimates of the external costs of power generation in Cuba, functions obtained in international studies were used. The main objective of this work was to carry out a summarized critical analysis of those national analytic epidemiological studies that, according the exposed methodology, consider the main aspects specialized with views to the possible preliminary proposal of functions exposure-response (FER) based own in epidemiologic evidences. In agreement with the analysis, the results show that the great majority of the studies are not useful for the FER establishment, at least in their present form. A minority studies exists that contributes limited evidence and their reanalysis could increase their contribution to the propose purpose. Finally the main problems found in the studies are enumerated revision object

  17. Prevalence of risk factors for stuttering among boys: analytical cross-sectional study

    Directory of Open Access Journals (Sweden)

    Cristiane Moço Canhetti Oliveira

    Full Text Available CONTEXT AND OBJECTIVE:There have been few studies on the risk factors for subgroups of stuttering. The aim of this study was to characterize the risk factors for developmental familial stuttering among boys who stutter and who do not stutter, such as disfluency types, associated quality and communication factors, emotional and physical stress, familial attitudes and personal reactions.DESIGN AND SETTING:Analytical cross-sectional study with a control group, performed at the Fluency Studies Laboratory of the Department of Speech and Hearing Disorders of a public university.METHODS: The parents of 40 age-matched stuttering and non-stuttering boys took part in this study. The participants were divided into two groups: stuttering children (SC and non-stuttering children (NSC, with ages between 6 years 0 months and 11 years 11 months. Initially, all of the participants underwent a fluency assessment and then data were gathered using the Protocol for the Risk of Developmental Stuttering.RESULTS:There were no differences in the physical stress distribution factors and personal reactions between the groups. Inappropriate familial attitudes were presented by 95% of the SC and 30% of the NSC. Four risk factors analyzed were not shown by the NSC, namely stuttering-like disfluency, quality factors, physical stress and emotional stresses.CONCLUSIONS:The findings suggest that the presence of stuttering-like disfluency, associated quality and communication factors, emotional stress and inappropriate family attitudes are important risk factors for familial developmental stuttering among boys.

  18. An Empirical Study on the Preference of Supermarkets with Analytic Hierarchy Process Model

    Science.gov (United States)

    Weng Siew, Lam; Singh, Ranjeet; Singh, Bishan; Weng Hoe, Lam; Kah Fai, Liew

    2018-04-01

    Large-scale retailers are very important to the consumers in this fast-paced world. Selection of desirable market to purchase products and services becomes major concern among consumers in their daily life due to vast choices available. Therefore, the objective of this paper is to determine the most preferred supermarket among AEON, Jaya Grocer, Tesco, Giant and Econsave by the undergraduate students in Malaysia with Analytic Hierarchy Process (AHP) model. Besides that, this study also aims to determine the priority of decision criteria in the selection of supermarkets among the undergraduatestudents with AHP model. The decision criteria employed in this study are product quality, competitive price, cleanliness, product variety, location, good price labelling, fast checkout and employee courtesy. The results of this study show that AEON is the most preferred supermarket followed by Jaya Grocer, Tesco, Econsave and Giant among the students based on AHP model. Product quality, cleanliness and competitive price are ranked as the top three influential factors in this study. This study is significant because it helps to determine the most preferred supermarket as well as the most influential decision criteria in the preference of supermarkets among the undergraduate students with AHP model.

  19. The application of analytical methods to the study of Pareto - optimal control systems

    Directory of Open Access Journals (Sweden)

    I. K. Romanova

    2014-01-01

    Full Text Available The subject of research articles - - methods of multicriteria optimization and their application for parametric synthesis of double-circuit control systems in conditions of inconsistency of individual criteria. The basis for solving multicriteria problems is a fundamental principle of a multi-criteria choice - the principle of the Edgeworth - Pareto. Getting Pareto - optimal variants due to inconsistency of individual criteria does not mean reaching a final decision. Set these options only offers the designer (DM.An important issue when using traditional numerical methods is their computational cost. An example is the use of methods of sounding the parameter space, including with use of uniform grids and uniformly distributed sequences. Very complex computational task is the application of computer methods of approximation bounds of Pareto.The purpose of this work is the development of a fairly simple search methods of Pareto - optimal solutions for the case of the criteria set out in the analytical form.The proposed solution is based on the study of the properties of the analytical dependences of criteria. The case is not covered so far in the literature, namely, the topology of the task, in which no touch of indifference curves (lines level. It is shown that for such tasks may be earmarked for compromise solutions. Prepositional use of the angular position of antigradient to the indifference curves in the parameter space relative to the coordinate axes. Formulated propositions on the characteristics of comonotonicity and contramonotonicity and angular characteristics of antigradient to determine Pareto optimal solutions. Considers the General algorithm of calculation: determine the scope of permissible values of parameters; investigates properties comonotonicity and contraventanas; to build an equal level (indifference curves; determined touch type: single sided (task is not strictly multicriteria or bilateral (objective relates to the Pareto

  20. QA lessons learned for parameter control from the WIPP Project

    International Nuclear Information System (INIS)

    Richards, R.R.

    1998-01-01

    This paper provides a summary of lessons learned from experiences on the Waste Isolation Pilot Plant (WJPP) Project in implementation of quality assurance controls surrounding inputs for performance assessment analysis. Since the performance assessment (PA) process is inherent in compliance determination for any waste repository, these lessons-learned are intended to be useful to investigators, analysts, and Quality Assurance (QA) practitioners working on high level waste disposal projects. On the WIPP Project, PA analyses for regulatory-compliance determination utilized several inter-related computer programs (codes) that mathematically modeled phenomena such as radionuclide release, retardation, and transport. The input information for those codes are the parameters that are the subject of this paper. Parameters were maintained in a computer database, which was then queried electronically by the PA codes whenever input was needed as the analyses were run

  1. Multi-criteria approach with linear combination technique and analytical hierarchy process in land evaluation studies

    Directory of Open Access Journals (Sweden)

    Orhan Dengiz

    2018-01-01

    Full Text Available Land evaluation analysis is a prerequisite to achieving optimum utilization of the available land resources. Lack of knowledge on best combination of factors that suit production of yields has contributed to the low production. The aim of this study was to determine the most suitable areas for agricultural uses. For that reasons, in order to determine land suitability classes of the study area, multi-criteria approach was used with linear combination technique and analytical hierarchy process by taking into consideration of some land and soil physico-chemical characteristic such as slope, texture, depth, derange, stoniness, erosion, pH, EC, CaCO3 and organic matter. These data and land mapping unites were taken from digital detailed soil map scaled as 1:5.000. In addition, in order to was produce land suitability map GIS was program used for the study area. This study was carried out at Mahmudiye, Karaamca, Yazılı, Çiçeközü, Orhaniye and Akbıyık villages in Yenişehir district of Bursa province. Total study area is 7059 ha. 6890 ha of total study area has been used as irrigated agriculture, dry farming agriculture, pasture while, 169 ha has been used for non-agricultural activities such as settlement, road water body etc. Average annual temperature and precipitation of the study area are 16.1oC and 1039.5 mm, respectively. Finally after determination of land suitability distribution classes for the study area, it was found that 15.0% of the study area has highly (S1 and moderately (S2 while, 85% of the study area has marginally suitable and unsuitable coded as S3 and N. It was also determined some relation as compared results of linear combination technique with other hierarchy approaches such as Land Use Capability Classification and Suitability Class for Agricultural Use methods.

  2. Familiarity Vs Trust: A Comparative Study of Domain Scientists' Trust in Visual Analytics and Conventional Analysis Methods.

    Science.gov (United States)

    Dasgupta, Aritra; Lee, Joon-Yong; Wilson, Ryan; Lafrance, Robert A; Cramer, Nick; Cook, Kristin; Payne, Samuel

    2017-01-01

    Combining interactive visualization with automated analytical methods like statistics and data mining facilitates data-driven discovery. These visual analytic methods are beginning to be instantiated within mixed-initiative systems, where humans and machines collaboratively influence evidence-gathering and decision-making. But an open research question is that, when domain experts analyze their data, can they completely trust the outputs and operations on the machine-side? Visualization potentially leads to a transparent analysis process, but do domain experts always trust what they see? To address these questions, we present results from the design and evaluation of a mixed-initiative, visual analytics system for biologists, focusing on analyzing the relationships between familiarity of an analysis medium and domain experts' trust. We propose a trust-augmented design of the visual analytics system, that explicitly takes into account domain-specific tasks, conventions, and preferences. For evaluating the system, we present the results of a controlled user study with 34 biologists where we compare the variation of the level of trust across conventional and visual analytic mediums and explore the influence of familiarity and task complexity on trust. We find that despite being unfamiliar with a visual analytic medium, scientists seem to have an average level of trust that is comparable with the same in conventional analysis medium. In fact, for complex sense-making tasks, we find that the visual analytic system is able to inspire greater trust than other mediums. We summarize the implications of our findings with directions for future research on trustworthiness of visual analytic systems.

  3. An Analytical Study to Measure the Efficiency of Advertising on Sale Apple Product as Case Study

    OpenAIRE

    Karwan Talaat Rashid

    2017-01-01

    The study is exploratory in nature, and the inductive approach of the research has been used, to identify the impact of relations between advertising and sales. The purpose of the study is to show how advertising can be used for many different markets in the different type of products, to capture an audience’s attention. The study is based on primary data collected through the structured questionnaire visiting the respondents and some other population of study online responded in the question...

  4. WEB ANALYTICS COMBINED WITH EYE TRACKING FOR SUCCESSFUL USER EXPERIENCE DESIGN: A CASE STUDY

    OpenAIRE

    Magdalena BORYS; Monika CZWÓRNÓG; Tomasz RATAJCZYK

    2016-01-01

    The authors propose a new approach for the mobile user experience design process by means of web analytics and eye-tracking. The proposed method was applied to design the LUT mobile website. In the method, to create the mobile website design, data of various users and their behaviour were gathered and analysed using the web analytics tool. Next, based on the findings from web analytics, the mobile prototype for the website was created and validated in eye-tracking usability testing. The analy...

  5. WEB ANALYTICS COMBINED WITH EYE TRACKING FOR SUCCESSFUL USER EXPERIENCE DESIGN: A CASE STUDY

    Directory of Open Access Journals (Sweden)

    Magdalena BORYS

    2016-12-01

    Full Text Available The authors propose a new approach for the mobile user experience design process by means of web analytics and eye-tracking. The proposed method was applied to design the LUT mobile website. In the method, to create the mobile website design, data of various users and their behaviour were gathered and analysed using the web analytics tool. Next, based on the findings from web analytics, the mobile prototype for the website was created and validated in eye-tracking usability testing. The analysis of participants’ behaviour during eye-tracking sessions allowed improvements of the prototype.

  6. Analytical and Numerical Study of Foam-Filled Corrugated Core Sandwich Panels under Low Velocity Impact

    Directory of Open Access Journals (Sweden)

    Mohammad Nouri Damghani

    2016-05-01

    Full Text Available Analytical and finite element simulations are used to predict the effect of core density on the energy absorption of composite sandwich panels under low-velocity impact. The composite sandwich panel contains two facesheets and a foam-filled corrugated core. Analytical model is defined as a two degree-of-freedom system based on equivalent mass, spring, and dashpot to predict the local and global deformation response of a simply supported panel. The results signify a good agreement between analytical and numerical predictions.

  7. SU-F-T-226: QA Management for a Large Institution with Multiple Campuses for FMEA

    Energy Technology Data Exchange (ETDEWEB)

    Tang, G; Chan, M; Lovelock, D; Lim, S; Febo, R; DeLauter, J; Both, S; Li, X; Ma, R; Saleh, Z; Song, Y; Tang, X; Xiong, W; Hunt, M; LoSasso, T [Memorial Sloan Kettering Cancer Center, New York, NY (United States)

    2016-06-15

    Purpose: To redesign our radiation therapy QA program with the goal to improve quality, efficiency, and consistency among a growing number of campuses at a large institution. Methods: A QA committee was established with at least one physicist representing each of our six campuses (22 linacs). Weekly meetings were scheduled to advise on and update current procedures, to review end-to-end and other test results, and to prepare composite reports for internal and external audits. QA procedures for treatment and imaging equipment were derived from TG Reports 142 and 66, practice guidelines, and feedback from ACR evaluations. The committee focused on reaching a consensus on a single QA program among all campuses using the same type of equipment and reference data. Since the recommendations for tolerances referenced to baseline data were subject to interpretation in some instances, the committee reviewed the characteristics of all machines and quantified any variations before choosing between treatment planning system (i.e. treatment planning system commissioning data that is representative for all machines) or machine-specific values (i.e. commissioning data of the individual machines) as baseline data. Results: The configured QA program will be followed strictly by all campuses. Inventory of available equipment has been compiled, and additional equipment acquisitions for the QA program are made as needed. Dosimetric characteristics are evaluated for all machines using the same methods to ensure consistency of beam data where possible. In most cases, baseline data refer to treatment planning system commissioning data but machine-specific values are used as reference where it is deemed appropriate. Conclusion: With a uniform QA scheme, variations in QA procedures are kept to a minimum. With a centralized database, data collection and analysis are simplified. This program will facilitate uniformity in patient treatments and analysis of large amounts of QA data campus

  8. Multi-analytical characterization of archaeological ceramics. A case study from the Sforza Castle (Milano, Italy).

    Science.gov (United States)

    Barberini, V.; Maspero, F.; Galimberti, L.; Fusi, N.

    2009-04-01

    The aim of this work was the characterization, using several analytical techniques, of a sample of ancient pottery found during archaeological excavations in the 14th century's Sforza Castle in Milano. The use of a multi-analytical approach is well established in the study of archaeological materials (e.g. Tite et al. 1984, Ribechini et al. 2008). The chemical composition of the sample was determined with X-ray fluorescence spectroscopy. The chemical composition is: SiO2 61.3(±3)%, Al2O3 22.5(±2)%, Fe2O3 7.19(±6)%, K2O 3.85(±1)%, MgO 1.6(±1)%, Na2O 1.6(±4)% (probably overestimated), TiO2 1.02(±2)%, CaO 0.93(±1)%, MnO 0.15(±1)% and P2O5 0.06(±2)%. The K2O content, important when dealing with TL dating, was determined also with atomic absorption spectrophotometry. The K2O content determined with atomic absorption is 3.86(±3)%, in agreement with X-ray fluorescence analysis. The mineralogical composition of the sample was determined with X-ray powder diffraction: quartz 59.6(±1) wt%, mica 37.8(±3) wt% and feldspar (plagioclase) 2.6(±2) wt%. The sample homogeneity was assessed with X-ray computerised tomography (CT), which is a very powerful non-destructive analysis tool for 3D characterization (Sèguin, 1991). CT images show differences in materials with different X-ray absorption (mainly depending on different densities) and 3D reconstruction has many interesting archaeological applications (e.g. study of sealed jars). CT images of the studied sample showed the presence of angular fragments (probably quartz) few millimetres wide immersed in a fine grained matrix. Moreover, before and after the CT analysis, some ceramic powder was sampled to perform thermoluminescence analysis (TL, the powder used for this analysis can not be recovered). It was thus possible to evaluate the dose absorbed by the material due the X-ray irradiation. The dose absorbed after 3 hours of irradiation, the time needed for a complete scan of a 7 x 5 x 1 cm, is about 100 Gy, which

  9. A Systematic Evaluation of Blood Serum and Plasma Pre-Analytics for Metabolomics Cohort Studies

    Directory of Open Access Journals (Sweden)

    Elodie Jobard

    2016-12-01

    Full Text Available The recent thriving development of biobanks and associated high-throughput phenotyping studies requires the elaboration of large-scale approaches for monitoring biological sample quality and compliance with standard protocols. We present a metabolomic investigation of human blood samples that delineates pitfalls and guidelines for the collection, storage and handling procedures for serum and plasma. A series of eight pre-processing technical parameters is systematically investigated along variable ranges commonly encountered across clinical studies. While metabolic fingerprints, as assessed by nuclear magnetic resonance, are not significantly affected by altered centrifugation parameters or delays between sample pre-processing (blood centrifugation and storage, our metabolomic investigation highlights that both the delay and storage temperature between blood draw and centrifugation are the primary parameters impacting serum and plasma metabolic profiles. Storing the blood drawn at 4 °C is shown to be a reliable routine to confine variability associated with idle time prior to sample pre-processing. Based on their fine sensitivity to pre-analytical parameters and protocol variations, metabolic fingerprints could be exploited as valuable ways to determine compliance with standard procedures and quality assessment of blood samples within large multi-omic clinical and translational cohort studies.

  10. Validation of analytical methods for the stability studies of naproxen suppositories for infant and adult use

    International Nuclear Information System (INIS)

    Rodriguez Hernandez, Yaslenis; Suarez Perez, Yania; Garcia Pulpeiro, Oscar

    2011-01-01

    Analytical and validating studies were performed in this paper, with a view to using them in the stability studies of the future formulations of naproxen suppositories for children and adults. The most influential factors in the naproxen stability were determined, that is, the major degradation occurred in acid medium, oxidative medium and by light action. One high-performance liquid chromatography-based method was evaluated, which proved to be adequate to quantify naproxen in suppositories and was selective against degradation products. The quantification limit was 3,480 μg, so it was valid for these studies. Additionally, the parameters specificity for stability, detection and quantification limits were evaluated for the direct semi-aqueous acid-base method, which was formerly validated for the quality control and showed satisfactory results. Nevertheless, the volumetric methods were not regarded as stability indicators; therefore, this method will be used along with the chromatographic methods of choice, that is, thin-layer chromatography and highperformance liquid chromatography, to determine the degradation products

  11. Sustainable in-well vapor stripping: A design, analytical model, and pilot study for groundwater remediation

    Science.gov (United States)

    Sutton, Patrick T.; Ginn, Timothy R.

    2014-12-01

    A sustainable in-well vapor stripping system is designed as a cost-effective alternative for remediation of shallow chlorinated solvent groundwater plumes. A solar-powered air compressor is used to inject air bubbles into a monitoring well to strip volatile organic compounds from a liquid to vapor phase while simultaneously inducing groundwater circulation around the well screen. An analytical model of the remediation process is developed to estimate contaminant mass flow and removal rates. The model was calibrated based on a one-day pilot study conducted in an existing monitoring well at a former dry cleaning site. According to the model, induced groundwater circulation at the study site increased the contaminant mass flow rate into the well by approximately two orders of magnitude relative to ambient conditions. Modeled estimates for 5 h of pulsed air injection per day at the pilot study site indicated that the average effluent concentrations of dissolved tetrachloroethylene and trichloroethylene can be reduced by over 90% relative to the ambient concentrations. The results indicate that the system could be used cost-effectively as either a single- or multi-well point technology to substantially reduce the mass of dissolved chlorinated solvents in groundwater.

  12. Prevalence of burnout syndrome in oncology nursing: A meta-analytic study.

    Science.gov (United States)

    Cañadas-De la Fuente, Guillermo A; Gómez-Urquiza, Jose L; Ortega-Campos, Elena M; Cañadas, Gustavo R; Albendín-García, Luis; De la Fuente-Solana, Emilia I

    2018-05-01

    To determine the prevalence of high levels of emotional exhaustion and depersonalization and low personal accomplishment in nursing professionals in oncology services. A meta-analytical study was performed. The search was carried out in March 2017 in Pubmed, CINAHL, Scopus, Scielo, Proquest, CUIDEN, and LILACS databases. Studies using Maslach Burnout Inventory for the assessment of burnout were included. The total sample of oncology nurses was n = 9959. The total number of included studies was n = 17, with n = 21 samples for the meta-analysis of emotional exhaustion and n = 18 for depersonalization and low personal accomplishment. The prevalence of emotional exhaustion and of depersonalization was 30% (95% CI = 26%-33%) and 15% (95% CI = 9%-23%), respectively, and that of low personal performance was 35% (95% CI = 27%-43%). The are many oncology nurses with emotional exhaustion and low levels of personal accomplishment. The presence and the risk of burnout among these staff members are considerable. Copyright © 2018 John Wiley & Sons, Ltd.

  13. Depression among HIV/AIDS Sudanese patients: a cross-sectional analytic study.

    Science.gov (United States)

    Elbadawi, Abdulateef; Mirghani, Hyder

    2017-01-01

    Depression and HIV/AIDS are common morbid health problems; the relationship is bidirectional exacerbating each other with deleterious consequences. There are limited studies on this topic in Sudan. In this study, we investigated depression among HIV/AIDS in Sudan. A cross-sectional analytic study was conducted among 362 HIV/AIDS patients from three centers in Khartoum, Sudan. Data were collected by the Hospital Depression and Anxiety (HADS) questionnaire. Chi-square was used for testing the significance and a P. Value of ≥ 0.05 was considered as statistically significant. Depression was evident in 332 (63.1%) of patients 68 (19.3%) had mild depression, 114 (32.4%) moderate depression, and 40 (11.4%) severe depression. Depression was commoner among women, illiterate, married/widowed, not receiving counseling, delaying the result of the test, P-value 0.05. Depression was prevalent among HIV/AIDS patients, especially females, low level of education, and widowed/married patients, and those not receiving counseling and post diagnosis sessions.

  14. The Education of English Language Learners in Arizona: A Legacy of Persisting Achievement Gaps in a Restrictive Language Policy Climate

    Science.gov (United States)

    Garcia, Eugene E.; Lawton, Kerry; Diniz de Figueiredo, Eduardo H.

    2010-01-01

    This report reviews achievement gaps in both reading and math between ELL and non-ELL students in Arizona over the post-Proposition 203 period 2005-2009 and during the first year of implementation of the 4 hour ELD block, 2008-09. The study finds that Arizona has made little to no progress in closing the achievement gap between ELL and non-ELL…

  15. Analytical characterization of recombinant hCG and comparative studies with reference product.

    Science.gov (United States)

    Thennati, Rajamannar; Singh, Sanjay Kumar; Nage, Nitin; Patel, Yena; Bose, Sandip Kumar; Burade, Vinod; Ranbhor, Ranjit Sudhakar

    2018-01-01

    Regulatory agencies recommend a stepwise approach for demonstrating biosimilarity between a proposed biosimilar and reference biological product emphasizing for functional and structural characterization to trace if there is any difference which may impact safety and efficacy. We studied the comparative structural and biological attributes of recombinant human chorionic gonadotropin (rhCG), SB005, with reference product, Ovidrel ® and Ovitrelle ® . Recombiant hCG was approved in 2000 by the US Food and Drug Administration for the induction of final follicular maturation, early luteinization in infertile women as part of assisted reproductive technology program. It is also indicated for the induction of ovulation and pregnancy in ovulatory infertile patients whose cause of infertility is not due to ovarian failure. Primary structure was studied by intact mass analysis, peptide fingerprinting, peptide mass fingerprinting and sequence coverage analysis. Higher order structure was studied by circular dichroism, ultraviolet-visible spectroscopy, fluorescence spectroscopy, and disulfide bridge analysis. Different isoforms of reference product and SB005 were identified using capillary isoelectric focusing and capillary zone electrophoresis. Glycosylation was studied by N-glycan mapping using LC-ESI-MS, point of glycosylation, released glycan analysis using ultra performance liquid chromatography and sialic acid analysis. Product related impurities such as oligomer content analysis and oxidized impurities were studied using size exclusion chromatography and reverse phase high performance liquid chromatography, respectively. Biological activity in term of potency of reference product and SB005 was studied by in vivo analysis. In this study we have compared analytical similarity of recombinant rhCG (SB005) produced at Sun Pharmaceuticals with the reference product with respect to its primary, higher order structure, isoforms, charge variants, glycosylation, sialyation

  16. Hydrogeology of the Mogollon Highlands, central Arizona

    Science.gov (United States)

    Parker, John T.C.; Steinkampf, William C.; Flynn, Marilyn E.

    2005-01-01

    The Mogollon Highlands, 4,855 square miles of rugged, mountainous terrain at the southern edge of the Colorado Plateau in central Arizona, is characterized by a bedrock-dominated hydrologic system that results in an incompletely integrated regional ground-water system, flashy streamflow, and various local water-bearing zones that are sensitive to drought. Increased demand on the water resources of the area as a result of recreational activities and population growth have made necessary an increased understanding of the hydrogeology of the region. The U.S. Geological Survey conducted a study of the geology and hydrology of the region in cooperation with the Arizona Department of Water Resources under the auspices of the Arizona Rural Watershed Initiative, a program launched in 1998 to assist rural areas in dealing with water-resources issues. The study involved the analysis of geologic maps, surface-water and ground-water flow, and water and rock chemical data and spatial relationships to characterize the hydrogeologic framework. The study area includes the southwestern corner of the Colorado Plateau and the Mogollon Rim, which is the eroded edge of the plateau. A 3,000- to 4,000-foot sequence of early to late Paleozoic sedimentary rocks forms the generally south-facing scarp of the Mogollon Rim. The area adjacent to the edge of the Mogollon Rim is an erosional landscape of rolling, step-like terrain exposing Proterozoic metamorphic and granitic rocks. Farther south, the Sierra Ancha and Mazatzal Mountain ranges, which are composed of various Proterozoic rocks, flank an alluvial basin filled with late Cenozoic sediments and volcanic flows. Eight streams with perennial to intermittent to ephemeral flow drain upland regions of the Mogollon Rim and flow into the Salt River on the southern boundary or the Verde River on the western boundary. Ground-water flow paths generally are controlled by large-scale fracture systems or by karst features in carbonate rocks. Stream

  17. Per-beam, planar IMRT QA passing rates do not predict clinically relevant patient dose errors

    Energy Technology Data Exchange (ETDEWEB)

    Nelms, Benjamin E.; Zhen Heming; Tome, Wolfgang A. [Canis Lupus LLC and Department of Human Oncology, University of Wisconsin, Merrimac, Wisconsin 53561 (United States); Department of Medical Physics, University of Wisconsin, Madison, Wisconsin 53705 (United States); Departments of Human Oncology, Medical Physics, and Biomedical Engineering, University of Wisconsin, Madison, Wisconsin 53792 (United States)

    2011-02-15

    Purpose: The purpose of this work is to determine the statistical correlation between per-beam, planar IMRT QA passing rates and several clinically relevant, anatomy-based dose errors for per-patient IMRT QA. The intent is to assess the predictive power of a common conventional IMRT QA performance metric, the Gamma passing rate per beam. Methods: Ninety-six unique data sets were created by inducing four types of dose errors in 24 clinical head and neck IMRT plans, each planned with 6 MV Varian 120-leaf MLC linear accelerators using a commercial treatment planning system and step-and-shoot delivery. The error-free beams/plans were used as ''simulated measurements'' (for generating the IMRT QA dose planes and the anatomy dose metrics) to compare to the corresponding data calculated by the error-induced plans. The degree of the induced errors was tuned to mimic IMRT QA passing rates that are commonly achieved using conventional methods. Results: Analysis of clinical metrics (parotid mean doses, spinal cord max and D1cc, CTV D95, and larynx mean) vs IMRT QA Gamma analysis (3%/3 mm, 2/2, 1/1) showed that in all cases, there were only weak to moderate correlations (range of Pearson's r-values: -0.295 to 0.653). Moreover, the moderate correlations actually had positive Pearson's r-values (i.e., clinically relevant metric differences increased with increasing IMRT QA passing rate), indicating that some of the largest anatomy-based dose differences occurred in the cases of high IMRT QA passing rates, which may be called ''false negatives.'' The results also show numerous instances of false positives or cases where low IMRT QA passing rates do not imply large errors in anatomy dose metrics. In none of the cases was there correlation consistent with high predictive power of planar IMRT passing rates, i.e., in none of the cases did high IMRT QA Gamma passing rates predict low errors in anatomy dose metrics or vice versa

  18. Quality assurance (QA) and quality control (QC) of image guided radiotherapy (IGRT). Osaka Rosai Hospital experience

    International Nuclear Information System (INIS)

    Tsuboi, Kazuki; Yagi, Masayuki; Fujiwara, Kanta

    2013-01-01

    The linear accelerator with image guided radiation therapy (IGRT) was introduced in May 2010. We performed the verification of the IGRT system, id est (i.e.), acceptance test and our original performance test and confirmed the acceptability for clinical use. We also performed daily QA/QC program before the start of treatment. One-year experience of QA/QC program showed excellent stability of IGRT function compared with our old machine. We further hope to establish the more useful management system and QA/QC program. (author)

  19. Per-beam, planar IMRT QA passing rates do not predict clinically relevant patient dose errors

    International Nuclear Information System (INIS)

    Nelms, Benjamin E.; Zhen Heming; Tome, Wolfgang A.

    2011-01-01

    Purpose: The purpose of this work is to determine the statistical correlation between per-beam, planar IMRT QA passing rates and several clinically relevant, anatomy-based dose errors for per-patient IMRT QA. The intent is to assess the predictive power of a common conventional IMRT QA performance metric, the Gamma passing rate per beam. Methods: Ninety-six unique data sets were created by inducing four types of dose errors in 24 clinical head and neck IMRT plans, each planned with 6 MV Varian 120-leaf MLC linear accelerators using a commercial treatment planning system and step-and-shoot delivery. The error-free beams/plans were used as ''simulated measurements'' (for generating the IMRT QA dose planes and the anatomy dose metrics) to compare to the corresponding data calculated by the error-induced plans. The degree of the induced errors was tuned to mimic IMRT QA passing rates that are commonly achieved using conventional methods. Results: Analysis of clinical metrics (parotid mean doses, spinal cord max and D1cc, CTV D95, and larynx mean) vs IMRT QA Gamma analysis (3%/3 mm, 2/2, 1/1) showed that in all cases, there were only weak to moderate correlations (range of Pearson's r-values: -0.295 to 0.653). Moreover, the moderate correlations actually had positive Pearson's r-values (i.e., clinically relevant metric differences increased with increasing IMRT QA passing rate), indicating that some of the largest anatomy-based dose differences occurred in the cases of high IMRT QA passing rates, which may be called ''false negatives.'' The results also show numerous instances of false positives or cases where low IMRT QA passing rates do not imply large errors in anatomy dose metrics. In none of the cases was there correlation consistent with high predictive power of planar IMRT passing rates, i.e., in none of the cases did high IMRT QA Gamma passing rates predict low errors in anatomy dose metrics or vice versa. Conclusions: There is a lack of correlation between

  20. Discussion of Regulatory Guide 7.10, emphasizing the graded approach for establishing QA programs

    International Nuclear Information System (INIS)

    Gordon, L.; Lake, W.H.

    1983-01-01

    To assist applicants in establishing an acceptable QA program to meet the programmatic elements of Appendix E to 10 CFR Part 71, Regulatory Guide 7.10 was developed. Regulatory Guide 7.10 is organized in three self-contained ANNEXES. Guidance applicable to designer/fabricators, to users, and users of radiographic devices are in separate annexes. QA programs for packaging to transport radioactive material are similar in regard to the various operations a licensee may be involved in. However, the appropriate QA/QC effort to verify the program elements may vary significantly. This is referred to as the graded approach. Appendix A in the guide addresses the graded approach