WorldWideScience

Sample records for aqueous solution extractions

  1. Acetic acid extraction from aqueous solutions using fatty acids

    NARCIS (Netherlands)

    IJmker, H.M.; Gramblicka, M.; Kersten, S.R.A.; Ham, van der A.G.J.; Schuur, B.

    2014-01-01

    A major challenge for production of acetic acid via bio-based routes is cost-effective concentration and purification of the acetic acid from the aqueous solutions, for which liquid–liquid extraction is a possible method. A main challenge in extraction of acetic acid from dilute aqueous solutions is

  2. [Extraction of alpha-cypermethrin from aqueous methanol solutions].

    Science.gov (United States)

    Shormanov, V K; Chigareva, E N; Belousova, O V

    2010-01-01

    Alpha cypermethrin was extracted from aqueous methanol solutions using hydrophobic organic solvents. The efficiency of extraction was shown to depend on the chemical nature of the solvent, the water to methanol ratio, and saturation of the aqueous methanol layer with an electrolyte. Optimal extraction of alpha-cypermethrin was achieved using toluene as the solvent under desalinization conditions. The extraction factor for the removal of the sought amount of alpha-cypermethrin from the water-methanol solution (4:1) using various solvents was calculated.

  3. Reactive Extraction of Alcohols from Apolar Hydrocarbons with Aqueous Solutions

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The aqueous solutions are evaluated as sustainable reactive extraction solvents for the recovery of monohydroxyl alcohols (benzyl alcohol, 1-hexanol, cyclohexanol) present in few-percent concentrations in apolar hydrocarbons (toluene, n-hexane, and cyclohexane) by considering two approaches. An aqueous solution containing a reactive extractant, like borate salts, borate complexes, a monosalt of dicarboxylic acid,hydroxypropyl-cyclodextrins, and silver nitrate, shows limited potential to be used. Another approach, in which the alcohol is chemically modified prior to the extraction into an easy-extractable form, in this case a monoesterlcarboxylic acid, shows much more potential. An environmentally benign aqueous solution of sodium hydrogen carbonate can provide a distribution ratio of benzyl alcohol up to 200, leaving the solubility of the organic solvent in the aqueous solution unchanged relative to pure water and therefore increasing the selectivity with two orders of magnitude. The modification of aromatic, cyclo-aliphatic, and linear aliphatic alcohols can be performed efficiently in the apolar organic solvent without need for a catalyst. The recovery of the modified alcohol can be performed by back-extraction in combination with a spontaneous hydrolysis.

  4. Reactive Extraction of Alcohols from Apolar Hydrocarbons with Aqueous Solutions

    NARCIS (Netherlands)

    Kuzmanovic, Boris; Kuipers, Norbert J.M.; Haan, de André B.; Kwant, Gerard

    2006-01-01

    The aqueous solutions are evaluated as sustainable reactive extraction solvents for the recovery of monohydroxyl alcohols (benzyl alcohol, 1-hexanol, cyclohexanol) present in few-percent concentrations in apolar hydrocarbons (toluene, n-hexane, and cyclohexane) by considering two approaches. An aque

  5. Batch liquid-liquid extraction of phenol from aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Palma, M.S.A.; Shibata, C. [Department of Biochemical Pharmaceutical Technology, Faculty of Pharmaceutical Sciences, University of Sao Paulo, Sao Paulo-SP (Brazil); Paiva, J.L. [Department of Chemical Engineering, Polytechnical School, University of Sao Paulo, Sao Paulo-SP (Brazil); Zilli, M. [Department of Chemical and Process Engineering, University of Genoa, Genoa (Italy); Converti, A.

    2010-01-15

    The aim of this work is the study of batch liquid-liquid extraction of phenol from aqueous solutions in a bench-scale well-mixed reactor. The influence of the ratio of phase volumes, temperature, and rotational speed on phenol removal (0.72-1.1 % w/w) was investigated using methyl isobutyl ketone as an extracting solvent. For this purpose, the ratio of phase volumes were set at 0.1 and 0.2, the temperature at 10, 20, and 30 C, and the rotational speed at 300, 400, and 500 rpm. A physical model based on the material balance of the phases as well as the equation of mass flux between the phases allowed the estimation of the overall coefficient of mass transfer coupled with the superficial area. Moreover, it proved to fit, satisfactorily well, the experimental data of residual phenol concentration in the organic phase versus time under all the conditions investigated. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

  6. [Extraction of 2-amino-4-nitrophenol and 4-phenylphenol from aqueous solutions].

    Science.gov (United States)

    Fursova, I A; Shormanov, V K

    2002-01-01

    The authors provide the results of extraction of 2-amino-4-nitrophenol and 4-phenilphenol from aqueous solutions by five organic soluvants. The dependence of the extraction degree on some factors (nature of extragent, pH of aqueous phase medium, extragents saturation with water) was established. Necessary extraction rate for isolation of preset quality of the test substances was calculated.

  7. Efficient removal of naphthalene-2-ol from aqueous solutions by solvent extraction.

    Science.gov (United States)

    Shao, Jingjing; Cheng, Yan; Yang, Chunping; Zeng, Guangming; Liu, Wencan; Jiao, Panpan; He, Huijun

    2016-09-01

    Naphthalene-2-ol is a typical biologically recalcitrant pollutant in dye wastewater. Solvent extraction of naphthalene-2-ol from aqueous solutions using mixed solvents was investigated. Various extractants and diluents were evaluated, and the effects of volume ratio of extractant to diluent, initial pH, initial concentration of naphthalene-2-ol in aqueous solution, extraction time, temperature, volume ratio of organic phase to aqueous phase (O/A), stirring rate and extraction stages, on extraction efficiency were examined separately. Regeneration and reuse of the spent extractant were also investigated. Results showed that tributyl phosphate (TBP) achieved 98% extraction efficiency for naphthalene-2-ol in a single stage extraction, the highest among the 12 extractants evaluated. Extraction efficiency was optimized when cyclohexane and n-octane were used as diluents. The solvent combination of 20% TBP, 20% n-octanol and 60% cyclohexane (V/V) obtained the maximum extraction efficiency for naphthalene-2-ol, 99.3%, within 20min using three cross-current extraction stages under the following extraction conditions: O/A ratio of 1:1, initial pH of 3, 25°C and stirring rate of 150r/min. Recovery of mixed solvents was achieved by using 15% (W/W) NaOH solution at an O:A ratio of 1:1 and a contact time of 15min. The mixed solvents achieved an extraction capacity for naphthalene-2-ol stably higher than 90% during five cycles after regeneration.

  8. Preparation of nanoparticles of Magnolia bark extract by rapid expansion from supercritical solution into aqueous solutions.

    Science.gov (United States)

    He, Shuai; Zhou, Benjie; Zhang, Shouyao; Lei, Zhengjie; Zhang, Zhongyi

    2011-01-01

    A rapid expansion from supercritical solution into aqueous solution (RESSAS) technology was presented for the micronization of Chinese medicinal material. Magnolia bark extract (MBE) obtained by supercritical carbon dioxide (scCO₂) extraction technology was chosen as the experimental material. RESSAS process produced 303.0 nm nanoparticles (size distribution, 243.6-320.5 nm), which was significantly smaller than the 55.3 µm particles (size distribution, 8.3-102.4 µm) prepared by conventional mechanical milling. The effect of process parameters, including extraction temperature (30 °C, 40 °C, 50 °C), extraction pressure (200, 250, 300 bar) and nozzle size (50, 100, 200 µm), on the size distribution of nanoparticles was investigated. The characteristics of nanoparticles and materials were also studied by scanning electron microscopy (SEM) and laser light scattering (LLS). This study demonstrates that RESSAS is applicable for preparing nanoparticles of MBE at low operating temperature; the process is simple without any residual solvent.

  9. Extraction of cobalt(II) from aqueous solution by N,N'-carbonyl difatty amides

    Institute of Scientific and Technical Information of China (English)

    Emad A. Jaffar Al-Mulla; Khalid Waleed S. Al-Janabi

    2011-01-01

    The development of economic and environmentally friendly extractants to recover cobalt metal is required due to the increasing demand for this metal. In this study, solvent extraction of Co(Ⅱ) from aqueous solution using a mixture of N,N'-carbonyl difatty amides (CDFAs) synthesised from palm oil as the extractant was carried out. The effects of various parameters such as acid, contact time, extractant concentration, metal ion concentration and stripping agent and the separation of Co(Ⅱ) from other metal ions such as Fe(Ⅱ), Ni(Ⅱ), Zn(Ⅲ) and Cd(Ⅱ) were investigated. It was found that the extraction of Co(Ⅱ) into the organic phase involved the formation of 1:1 complexes. Co(Ⅱ) was successfully separated from commonly associated metal ions such as Fe(Ⅱ), Ni(Ⅱ), Zn(Ⅲ) and Cd(Ⅱ). Co(Ⅱ) stripping from the loaded organic phase was studied in aqueous solution. These results are useful to recover Co(Ⅱ) from aqueous solution utilising (CDFAs) as an extractant.

  10. Low-temperature liquid-liquid extraction of phenols from aqueous solutions with hydrophilic mixtures of extractants

    Science.gov (United States)

    Rudakov, O. B.; Khorokhordina, E. A.; Preobrazhenskii, M. A.; Rudakova, L. V.

    2016-08-01

    The volume ratios in acetonitrile-ethyl acetate (90 : 10, 95 : 5), acetonitrile-isopropanol-ethyl acetate (70 : 15 : 15, 80 : 5 : 15), and isopropanol-1-butanol (50 : 50) mixtures were determined. Their mixing with water (1 : 1) and storage at-10°C led to partitioning into two immiscible liquid phases without formation of the ice phase. The mixtures were shown to be useful as hydrophilic extractants in low-temperature liquidliquid extraction of phenol from aqueous solutions.

  11. Extraction of copper(II) ions from aqueous solutions with a methimazole-based ionic liquid.

    Science.gov (United States)

    Reyna-González, Juan M; Torriero, Angel A J; Siriwardana, Amal I; Burgar, Iko M; Bond, Alan M

    2010-09-15

    The recently synthesized ionic liquid (IL) 2-butylthiolonium bis(trifluoromethanesulfonyl)amide, [mimSBu][NTf(2)], has been used for the extraction of copper(II) from aqueous solution. The pH of the aqueous phase decreases upon addition of [mimSBu](+), which is attributed to partial release of the hydrogen attached to the N(3) nitrogen atom of the imidazolium ring. The presence of sparingly soluble water in [mimSBu][NTf(2)] also is required in solvent extraction studies to promote the incorporation of Cu(II) into the [mimSBu][NTf(2)] ionic liquid phase. The labile copper(II) system formed by interacting with both the water and the IL cation component has been characterized by cyclic voltammetry as well as UV-vis, Raman, and (1)H, (13)C, and (15)N NMR spectroscopies. The extraction process does not require the addition of a complexing agent or pH control of the aqueous phase. [mimSBu][NTf(2)] can be recovered from the labile copper-water-IL interacting system by washing with a strong acid. High selectivity of copper(II) extraction is achieved relative to that of other divalent cobalt(II), iron(II), and nickel(II) transition-metal cations. The course of microextraction of Cu(2+) from aqueous media into the [mimSBu][NTf(2)] IL phase was monitored in situ by cyclic voltammetry using a well-defined process in which specific interaction with copper is believed to switch from the ionic liquid cation component, [mimSBu], to the [NTf(2)] anion during the course of electrochemical reduction from Cu(II) to Cu(I). The microextraction-voltammetry technique provides a fast and convenient method to determine whether an IL is able to extract electroactive metal ions from an aqueous solution.

  12. Accumulation of yellow Monascus pigments by extractive fermentation in nonionic surfactant micelle aqueous solution.

    Science.gov (United States)

    Xiong, Xu; Zhang, Xuehong; Wu, Zhenqiang; Wang, Zhilong

    2015-02-01

    Monascus species can produce various secondary metabolites of polyketide structure. In the current study, it is found that an interesting phenomenon, i.e., submerged culture of Monascus species in an aqueous solution majorly accumulated intracellular orange Monascus pigments exhibiting one peak at 470 nm with absorbance of 32 OD while extractive fermentation in a nonionic surfactant micelle aqueous solution produced extracellular and intracellular yellow Monascus pigments exhibiting one peak at 410 nm with absorbance 30 OD and 12 OD, respectively. The spectrum profiles of both intracellular and extracellular Monascus pigments were affected by surfactant loading, extractive fermentation time, and surfactant adding time. Meanwhile, the instability of orange Monascus pigments in the extracellular nonionic surfactant micelle aqueous solution was also confirmed experimentally. The mechanism behind this phenomenon is attributed to the export of intracellular yellow Monascus pigments into its broth by extractive fermentation. The transferring of intracellular yellow Monascus pigments into its broth blocks yellow Monascus pigments from further enzymatic conversion or eliminates the feedback inhibition of yellow Monascus pigments based on the biosynthetic pathway of Monascus pigments.

  13. Extraction of Co(II) from aqueous solution using emulsion liquid membrane.

    Science.gov (United States)

    Gasser, M S; El-Hefny, N E; Daoud, J A

    2008-03-01

    The extraction equilibrium of Co(II) from thiocyanate medium by CYANEX 923 (mixture of straight chain alkylated phosphine oxides) in cyclohexane was studied. The stoichiometry of the extraction reaction was postulated based on slope analysis method and the extraction constant Kex was calculated. The stripping percentage of Co(II) with sulphuric acid from the loaded CYANEX 923 was found to increase with the increase in acid concentration. The extraction of Co(II) from aqueous thiocyanate medium into emulsion liquid membrane using CYANEX 923 extractant was also studied. The influence of different parameters such as stirring speed, surfactant concentration, pH of the extractant phase, carrier concentration, internal phase stripping acid concentration, initial Co(II) concentration as well as temperature on the emulsion stability were investigated. The applicability of the emulsion liquid membrane (ELM) process using CYANEX 923 as extractant and SPAN 80 as surfactant for the removal and the concentration of Co(II) from thiocyanate solution was investigated. The results show that it is possible to recover 95% of cobalt in the inner phase after 10 min of contacting time with a concentration factor of 5.

  14. Removing Boron from an Aqueous Solution Using Turmeric Extract-Aided Coagulation-Flocculation

    Directory of Open Access Journals (Sweden)

    Azhar Abdul Halim

    2012-01-01

    Full Text Available Problem statement: Boron exists in an environment naturally either through weathering of rocks or volcanic activity but due to anthropogenic activity, boron had been distributed widely into our surroundings. Boron was a problematic pollutant due to the difficulty to remove it from the water. Turmeric which had been widely used as a spice and traditional medicine, were investigated to determine its capabilities to aid in coagulation-flocculation process to remove boron. Optimizing coagulation-flocculation process might be effective to remove boron to a lower concentration. Approach: In this study, the optimum parameter for pH, dose of aluminium sulfate (alum and a dose of turmeric extract were determined by conducting a set of jar test experiment. The coagulation-flocculation process was performed to study the effectiveness of the turmeric extract as a coagulant aid in boron removal. Results: The result demonstrated that coagulation-flocculation process with the aid of turmeric extract can remove boron effectively at optimum conditions rather than coagulation-flocculation process without the aid of turmeric extract. The optimum conditions for boron removal were achieved at pH 7, an alum dosage of 18, 367 mg L-1 and turmeric extract dosage of 82 mg L-1. Conclusion/Recommendations: Result showed that removal of boron depends on pH, alum dosage and turmeric extract dosage. The boron removal percentage of the aqueous solution using the coagulation-flocculation process aided by the addition of turmeric extract and without the addition of turmeric extract were 95 and 62%, respectively. In addition, there was a significance difference between both processes. Turmeric extract as a coagulant aid demonstrated promising performance in boron removal and can be used as an alternative treatment to treat boron-containing wastewater.

  15. EXTRACTION AND SORPTION BENZOIC ACID FROM AQUEOUS SOLUTIONS OF POLYMERS BASED ON N-VINYLAMIDES

    Directory of Open Access Journals (Sweden)

    A. G. Savvina

    2015-01-01

    Full Text Available The widespread use of aromatic acids (benzoic acid, salicylic as preservatives necessitates their qualitative and quantitative determination in food. Effective and common way to separation and concentration of aromatic acids liquid extraction. Biphasic system of water-soluble polymers based on (poly-N-vinyl pyrrolidone, and poly-N-vinylcaprolactam satisfy the requirements of the extraction system. When sorption concentration improved definition of the metrological characteristics, comply with the requirements for sensitivity and selectivity definition appears possible, use of inexpensive and readily available analytical equipment. When studying the adsorption of benzoic acid used as a sorbent crosslinked polymer based on N-vinyl pyrrolidone, obtained by radical polymerisation of a functional monomer and crosslinker. In the extraction of benzoic acid to maximize the allocation of water and the organic phase of the polymer used salt solutions with concentrations close to saturation. Regardless of the nature of the anion salt is used as salting-out agent, aromatic acids sorption increases with the size of the cations. In the experiment the maximum recovery rate (80% benzoic acid obtained in the PVP (0.2 weight%. Ammonium sulphate. The dependence stepepni benzoic acid extraction from time sorption sorbent mass and the pH of the aqueous phase. To establish equilibrium in the system, for 20 minutes. The dependence of the degree of extraction of the acid pH indicates that the acid is extracted into the molecular form. The maximum adsorption is reached at pH 3,5, with its efficiency decreases symbatically reduce the amount of undissociated acid molecules in solution.

  16. A novel cloud-point extraction process for preconcentrating selected polycyclic aromatic hydrocarbons in aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Bai, D.; Li, J.; Chen, S.B.; Chen, B.-H. [National University of Singapore (Singapore). Dept. of Chemical and Environmental Engineering

    2001-10-01

    Polycyclic aromatic hydrocarbons (PAHs) released in such processes as incomplete coal combustion and during the disposal of coal tar, are subject to strict emission controls in which the determination of PAHs has to be addressed. PAHs have low aqueous solubility which necessitates preconcentration prior to the analytical determination of PAHs. A novel but simple cloud-point extraction (CPE) process is developed to preconcentrate the trace of selected polycyclic aromatic hydrocarbons (PAHs) with the use of the readily biodegradable nonionic surfactant of secondary ethyoxylated alcohol Tergitol 15-S-7 as extractant. The concentrations of PAHs, mixtures of naphthalene and phenanthrene as well as pyrene in the spiked samples were determined with the new CPE process at ambient temperature (23{degree}C) followed by high performance liquid chromatography (HPLC) with fluorescence detection. More than 80% of phenanthrene and pyrene, respectively, and 96% of naphthalene initially present in the aqueous solutions with concentrations near or below their aqueous solubilities were recovered using this new CPE process. Importantly Tergitol 15-S-7 does not give any fluorometric signal to interfere with fluorescence detection of PAHs in the UV range. No special washing step is, thus, required to remove surfactant before HPLC analyses. Different experimental conditions were studied. The optimum conditions for the preconcentration and determination of these selected PAHs at ambient temperature have been established as the following: (1) 3 wt% surfactant; (2) addition of 0.5 M Na{sub 2}SO{sub 4}; (3) 10 min for equilibration time; and (4) 3000 rpm for centrifugal speed with duration of 10 min. 50 refs., 7 figs.

  17. Application of Moringa Peregrina seed extract as a natural coagulant for Phenol removal from aqueous solution

    Directory of Open Access Journals (Sweden)

    Edris Bazrafshan

    2013-02-01

    Conclusion: According to the obtained results, Moringa peregrina seed extract, with respect to its high efficacy, can be used as an effective, efficient, and inexpensive coagulant in removing phenol from aqueous environments.

  18. RECOVERY OF CARBOXYLIC ACIDS FROM AQUEOUS SOLUTIONS BY LIQUID-LIQUID EXTRACTION WITH A TRIISOOCTYLAMINE DILUENT SYSTEM

    Directory of Open Access Journals (Sweden)

    G. Malmary

    2001-12-01

    Full Text Available Tertiary alkylamines in solution with organic diluents are attractive extractants for the recovery of carboxylic acids from dilute aqueous phases. The aim of this study was to investigate the mechanism for extraction of organic acids from water by a long-chain aliphatic tertiary amine. In order to attain this objective, we studied the liquid-liquid equilibria between the triisooctylamine + 1-octanol + n-heptane system as solvent and an aqueous solution of an individual carboxylic acid such as citric, lactic and malic acids. The experiments showed that the partition coefficient for a particular organic acid depends on the kind of solute, notably when the acid concentration in the aqueous phase is low. A mathematical model, where both chemical association and physical distribution are taken into consideration, is proposed. The model suggests that the various complexes obtained between amine and organic acids contribute to the distribution of the solute between the coexisting phases in equilibrium.

  19. Transport extraction for trace element separation and preconcentration. Pt. 2; Preconcentration of iodine from aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Palagyi, S. (Inst. of Inorganic and Analytical Chemistry, L. Eoetvoes Univ., Budapest (Hungary)); Braun, T. (Inst. of Inorganic and Analytical Chemistry, L. Eoetvoes Univ., Budapest (Hungary))

    1993-08-01

    Transport extraction based on solvent sublation has been used for a 400-fold preconcentration of iodide from aqueous samples into an immiscible organic solvent. Separation efficiencies amounting up to 95% were obtained for iodide concentrations of 1-10 mg/l, independent of the volume of the aqueous samples in the range of 1-4l. Iodide was oxidized to iodine, which was subsequently transport-extracted as an ionic associate with the cationic surface-active agent N-cetylpyridinium chloride into 10ml of benzene. The effect of various parameters (concentration of iodide, bubbling time, N[sub 2]-gas flow-rate, volume of the aqueous phase) on transport extraction was investigated. Kinetic investigations showed that the transport-extraction process essentially follows a modified Langmuir adsorption model, which makes it possible to calculate the mass-transfer rate constant of the process for each particular case. (orig.)

  20. Indium recovery from acidic aqueous solutions by solvent extraction with D2EHPA: a statistical approach to the experimental design

    Directory of Open Access Journals (Sweden)

    Fortes M.C.B.

    2003-01-01

    Full Text Available This experimental work presents the optimization results of obtaining a high indium concentration solution and minimum iron poisoning by solvent extraction with D2EHPA solubilized in isoparaffin and exxsol. The variables studied in the extraction step were D2EHPA concentration, acidity of the aqueous phase and time of contact between phases. Different hydrochloric and sulfuric acid concentrations were studied for the stripping step. The optimum experimental conditions resulted in a solution with 99% indium extraction and less than 4% iron. The construction of a McCabe-Thiele diagram indicated two theoretical countercurrent stages for indium extraction and at least six stages for indium stripping. Finally, the influence of associated metals found in typical sulfate leach liquors from zinc plants was studied. Under the experimental conditions for maximum indium extraction, 96% indium extraction was obtained, iron extraction was about 4% and no Ga, Cu and Zn were co-extracted.

  1. Novel Regenerated Solvent Extraction Processes for the Recovery of Carboxylic Acids or Ammonia from Aqueous Solutions Part I. Regeneration of Amine-Carboxylic Acid Extracts

    Energy Technology Data Exchange (ETDEWEB)

    Poole, L.J.; King, C.J.

    1990-03-01

    Two novel regenerated solvent extraction processes are examined. The first process has the potential to reduce the energy costs inherent in the recovery of low-volatility carboxylic acids from dilute aqueous solutions. The second process has the potential for reducing the energy costs required for separate recovery of ammonia and acid gases (e.g. CO{sub 2} and H{sub 2}S) from industrial sour waters. The recovery of carboxylic acids from dilute aqueous solution can be achieved by extraction with tertiary amines. An approach for regeneration and product recovery from such extracts is to back-extract the carboxylic acid with a water-soluble, volatile tertiary amine, such as trimethylamine. The resulting trimethylammonium carboxylate solution can be concentrated and thermally decomposed, yielding the product acid and the volatile amine for recycle. Experimental work was performed with lactic acid, succinic acid, and fumaric acid. Equilibrium data show near-stoichiometric recovery of the carboxylic acids from an organic solution of Alamine 336 into aqueous solutions of trimethylamine. For fumaric and succinic acids, partial evaporation of the aqueous back extract decomposes the carboxylate and yields the acid product in crystalline form. The decomposition of aqueous solutions of trimethylammonium lactates was not carried out to completion, due to the high water solubility of lactic acid and the tendency of the acid to self-associate. The separate recovery of ammonia and acid gases from sour waters can be achieved by combining steam-stripping of the acid gases with simultaneous removal of ammonia by extraction with a liquid cation exchanger. The use of di-2,4,4-trimethylpentyl phosphinic acid as the liquid cation exchanger is explored in this work. Batch extraction experiments were carried out to measure the equilibrium distribution ratio of ammonia between an aqueous buffer solution and an organic solution of the phosphinic acid (0.2N) in Norpar 12. The concentration

  2. Thermal Stability Study of the Grape Seeds Extracts in the Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Carmen Pop

    2015-05-01

    Full Text Available This study was carried out to evaluate the effect of parameters the extraction process of grape seeds extracts on the bioactive compounds. The aqueous extracts were screened for total polyphenol content and total flavonoid content wich were determined spectrophotometrically using a modified Folin-Ciocalteu method, respectively a chromogenic system of NaNO2–Al (NO33–NaOH based method. The antioxidant activity was determined using DPPH method while  their polyphenolic composition by means of HPLC-DAD- MS/ ESI(+ analysis. Total phenols content and flavonoid content varied between 37.835 and 31.830 mg GAE/g, 23.420 and 17.645 mg QE/g respectively in Fetească Neagră seeds; between 24.265 and 27.065 mg GAE/g, 17.970 and 15.205 mg QE/g respectively in Fetească Regală seeds. All extracts showed remarkable DPPH radical-scavenging activity ranging from 94.110 to 95.515%. The study revealed 14 phenolic compounds belonging to the following groups: flavan-3-ol monomers, proanthocyanidins, hydroxycinnamic acid and hydroxybenzoic acid derivatives. Quantitative differences among the varieties and the level of temperature applied of  the extraction process were observed. The results suggested that the heat treatment of grape seeds liberated phenolic compounds having a significant effect in increasing the amounts of active when a 90°C extraction temperature was used.

  3. Removal of crystal violet dye from aqueous solution using triton X-114 surfactant via cloud point extraction

    Directory of Open Access Journals (Sweden)

    Arunagiri Appusamy

    2014-09-01

    Full Text Available In this work, the cloud point extraction (CPE was carried out for the removal of crystal violet dye from aqueous solution using triton X-114 surfactant. Density, refractive index and viscosity of pure components and two different phases of the mixture were measured, and the corresponding excess molar volume was calculated. Most of the dye molecules get solubilized in the coacervate phase, leaving a dye free dilute phase. This experiment was conducted for different sets of surfactant and solute concentration in order to find out the cloud point temperature and their influencing factors such as extraction efficiency, phase volume ratio, distribution coefficient and pre-concentration factor. Furthermore, the thermodynamic parameters like change in Gibbs-free energy (ΔG0, the change in enthalpy (ΔH0 and the change in entropy (ΔS0 were analyzed and found that cloud point extraction with surfactant was a more feasible process in the removal of dyes from aqueous solution.

  4. Removal of lead(II) from aqueous solutions using carbonate hydroxyapatite extracted from eggshell waste.

    Science.gov (United States)

    Liao, Dexiang; Zheng, Wei; Li, Xiaoming; Yang, Qi; Yue, Xiu; Guo, Liang; Zeng, Guangming

    2010-05-15

    Carbonate hydroxyapatite (CHAP) synthesized from eggshell waste was used for removing lead ion from aqueous solutions. The effects of pH, contact time and initial concentration were studied in batch experiments. The maximum uptake of lead ion was obtained at pH 6.0. Adsorption equilibrium was established by 60 min. The pseudo-first order, pseudo-second order and intraparticle diffusion kinetic models were applied to study the kinetics of the sorption processes. The pseudo-second order kinetic model provided the best correlation (R(2)>0.9991) of the used experimental data compared to the pseudo-first order and intraparticle diffusion kinetic models. The adsorption of lead ion by CHAP increased as the initial concentration of lead ion increased in the medium. The maximum lead ion adsorbed was found to be 101 mg g(-1). It was found that the adsorption of Pb(II) on CHAP was correlated well (R(2)=0.9995) with the Langmuir equation as compared to Freundlich isotherm equation under the concentration range studied. This study indicated that CHAP could be used as an efficient adsorbent for removal of lead ion from aqueous solution.

  5. Solvent extraction of Th(IV) from aqueous solution with methylimidazole in ionic liquid

    Energy Technology Data Exchange (ETDEWEB)

    Li, Wenkui; Lv, Hui; Liu, Ziyi; Wu, Jianrong; Li, Shun; Shen, Yinglin [Lanzhou Univ. (China). Radiochemistry Lab.; Yang, Shenghua [State Key Laboratory of Applied Organic Chemistry, Lanzhou (China)

    2016-07-01

    An extraction of Th(IV) was performed using 1-methylimidazole (1-MIM) or 2-methylimidazole (2-MIM) as the extractant in imidazolium type ionic liquids (ILs) or n-pentanol. The extractability for Th{sup 4+} in ILs was by far higher than that obtained in n-pentanol. The extraction mechanism was determined by slope analysis and ESI-MS. The transfer of Th{sup 4+} with MIM into ILs proceeded through both a cationic exchange and a neutral solvation mechanism, whereas the partitioning of Th{sup 4+} with MIM into n-pentanol only underwent a neutral solvation mechanism. The thermodynamic parameters values (ΔH, ΔS and ΔG) for extraction of Th{sup 4+} with 1-MIM in IL were calculated and the results indicated the extraction reaction was spontaneous and went through endothermic process. Separation of Th{sup 4+} from the solution of lanthanides (III) and uranium was also carried out by 1-MIM in ILs and n-pentanol.

  6. Adsorptive micro-extraction techniques--novel analytical tools for trace levels of polar solutes in aqueous media.

    Science.gov (United States)

    Neng, N R; Silva, A R M; Nogueira, J M F

    2010-11-19

    A novel enrichment technique, adsorptive μ-extraction (AμE), is proposed for trace analysis of polar solutes in aqueous media. The preparation, stability tests and development of the analytical devices using two geometrical configurations, i.e. bar adsorptive μ-extraction (BAμE) and multi-spheres adsorptive μ-extraction (MSAμE) is fully discussed. From the several sorbent materials tested, activated carbons and polystyrene divinylbenzene phases demonstrated the best stability, robustness and to be the most suitable for analytical purposes. The application of both BAμE and MSAμE devices proved remarkable performance for the determination of trace levels of polar solutes and metabolites (e.g. pesticides, disinfection by-products, drugs of abuse and pharmaceuticals) in water matrices and biological fluids. By comparing AμE techniques with stir bar sorptive extraction based on polydimethylsiloxane phase, great effectiveness is attained overcoming the limitations of the latter enrichment approach regarding the more polar solutes. Furthermore, convenient sensitivity and selectivity is reached through AμE techniques, since the great advantage of this new analytical technology is the possibility to choose the most suitable sorbent to each particular type of application. The enrichment techniques proposed are cost-effective, easy to prepare and work-up, demonstrating robustness and to be a remarkable analytical tool for trace analysis of priority solutes in areas of recognized importance such as environment, forensic and other related life sciences.

  7. Extraction of formic and acetic acids from aqueous solution by dynamic headspace-needle trap extraction temperature and pH optimization.

    Science.gov (United States)

    Lou, Da-Wei; Lee, Xinqing; Pawliszyn, Janusz

    2008-08-08

    A combined method of dynamic headspace-needle trap sample preparation and gas chromatography for the determination of formic and acetic acids in aqueous solution was developed in this study. A needle extraction device coupled with a gas aspirating pump was intended to perform sampling and preconcentration of target compounds from aqueous sample before gas chromatographic analysis. The needle trap extraction (NTE) technique allows for the successful sampling of short chain fatty acids under dynamic conditions while keeping the headspace (HS) volume constant. Two important parameters, including extraction temperature and effect of acidification, have been optimized and evaluated using the needle trap device. The method detection limits for the compounds estimated were 87.2microg/L for acetic acid and 234.8microg/L for formic acid in spite of the low flame ionization detection response for formic acid and its low Henry's law constant in aqueous solution. Precision was determined based on the two real samples and ranged between 4.7 and 10.7%. The validated headspace-needle trap extraction method was also successfully applied to several environmental samples.

  8. Treatment of Aqueous Solutions

    NARCIS (Netherlands)

    Van Spronsen, J.; Witkamp, G.J.

    2013-01-01

    The invention is directed to a process for the recovery or removal of one or more crystallizable compounds from an aqueous solution containing, apart from the said crystallizable compounds, one or more organic or inorganic scale- forming or scale-inducing materials having a lower solubility in water

  9. Extraction of nitric acid, uranyl nitrate, and bismuth nitrate from aqueous nitric acid solutions with CMPO

    Energy Technology Data Exchange (ETDEWEB)

    Spencer, B.B.

    1995-08-01

    DOE sponsored development of the transuranium extraction (TRUEX) process for removing actinides from radioactive wastes. The solvent is a mixture of CMPO and TBP. Since the extraction characteristics of CMPO are not as well understood as those of TBP, the extraction of nitric acid, uranyl nitrate, and bismuth nitrate with CMPO (dissolved in n-dodecane) were studied. Results indicate that CMPO extracts nitric acid with a 1:1 stoichiometry; equilibrium constant is 2. 660{plus_minus}0.092 at 25 C, and extraction enthalpy is -5. 46{plus_minus}0.46 kcal/mol. Slope analysis indicates that uranyl nitrate extracts with a mixed equilibria of 1:1 and 2:1 stoichiometries in nearly equal proportion. Equil. constant of the 2: 1 extraction was 1.213 {times} 10{sup 6}{plus_minus}3.56 {times} 10{sup 4} at 25 C; reaction enthalpy was -9.610{plus_minus}0.594 kcal/mol. Nitration complexation constant is 8.412{plus_minus}0.579, with an enthalpy of -10.72{plus_minus}1.87 kcal/mol. Bismuth nitrate also extracts with a mixed equilibria of (perhaps) 1:1 and 2:1 stoichiometries. A 2:1 extraction equilibrium and a nitrate complexation adequately model the data. Kinetics and enthalpies were also measured.

  10. Novel Regenerated Solvent Extraction Processes for the Recovery of Carboxylic Acids or Ammonia from Aqueous Solutions Part II. Recovery of Ammonia from Sour Waters

    Energy Technology Data Exchange (ETDEWEB)

    Poole, L.J.; King, C.J.

    1990-03-01

    Two novel regenerated solvent extraction processes are examined. The first process has the potential to reduce the energy costs inherent in the recovery of low-volatility carboxylic acids from dilute aqueous solutions. The second process has the potential for reducing the energy costs required for separate recovery of ammonia and acid gases (e.g. CO{sub 2} and H{sub 2}S) from industrial sour waters. The recovery of carboxylic acids from dilute aqueous solution can be achieved by extraction with tertiary amines. An approach for regeneration and product recovery from such extracts is to back-extract the carboxylic acid with a water-soluble, volatile tertiary amine, such as trimethylamine. The resulting trimethylammonium carboxylate solution can be concentrated and thermally decomposed, yielding the product acid and the volatile amine for recycle. Experimental work was performed with lactic acid, SUCCiOlC acid, and fumaric acid. Equilibrium data show near-stoichiometric recovery of the carboxylic acids from an organic solution of Alamine 336 into aqueous solutions of trimethylamine. For fumaric and succinic acids, partial evaporation of the aqueous back extract decomposes the carboxylate and yields the acid product in crystalline form. The decomposition of aqueous solutions of trimethylammonium lactates was not carried out to completion, due to the high water solubility of lactic acid and the tendency of the acid to self-associate. The separate recovery of ammonia and acid gases from sour waters can be achieved by combining steam-stripping of the acid gases with simultaneous removal of ammonia by extraction with a liquid cation exchanger. The use of di-2,4,4-trimethylpentyl phosphinic acid as the liquid cation exchanger is explored in this work. Batch extraction experiments were carried out to measure the equilibrium distribution ratio of ammonia between an aqueous buffer solution and an organic solution of the phosphinic acid (0.2N) in Norpar 12. The concentration

  11. Synergic effects in the extraction of paracetamol from aqueous NaCl solution by the binary mixtures of diethyl ether and low molecular weight primary alcohols

    Science.gov (United States)

    Nikolić, G. M.; Živković, J. V.; Atanasković, D. S.; Nikolić, M. G.

    2013-12-01

    Liquid-liquid extraction of paracetamol from aqueous NaCl solutions was performed with diethyl ether, 1-propanol, 1-butanol, isobutanol, 1-pentanol, and binary mixtures diethyl ether/1-propanol, diethyl ether/1-butanol, and diethyl ether/isobutanol. Among the pure solvents investigated in this study best extraction efficacy was obtained with 1-butanol. Synergic effects in the extraction with binary mixtures was investigated and compared with some other systems used for the extraction of poorly extractable compounds. Results obtained in this study may be of both fundamental and practical importance.

  12. Selective adsorption of Pb(II) from aqueous solution using porous biosilica extracted from marine diatom biomass: Properties and mechanism

    Science.gov (United States)

    Qi, Yarong; Wang, Jingfeng; Wang, Xin; Cheng, Jay Jiayang; Wen, Zhiyou

    2017-02-01

    Biosilica with a surface area of 143 m2 g-1 derived from marine diatoms was prepared using an easy two-step method involving washing with dilute acid and baking. The extracted biosilica was used to remove divalent lead ions, i.e., Pb(II), from aqueous solution. The effects on Pb(II) adsorption of initial pH, shaking speed, and adsorbent loading were investigated. The adsorption of Pb(II) in the presence of other ions was also investigated. The biosilica showed a high adsorption capacity with high selectivity for Pb(II). The experimental maximum adsorption capacity was 108.2-120.4 mg g-1 at an adsorbent loading of 1 g L-1. The adsorption process was best described by the Langmuir model. The adsorbent selectively adsorbed Pb(II) from binary ion systems in the presence of Cu(II), Cd(II), Ni(II), and Ag(I). The results of this study show that biosilica extracted from fresh marine diatoms is a more efficient and selective adsorbent for Pb(II) than other inorganic adsorbents.

  13. Reactive extraction of carboxylic acids from apolar hydrocarbons using aqueous solutions of sodium hydrogen carbonate with back-recovery using carbon dioxide under pressure

    NARCIS (Netherlands)

    Kuzmanovic, Boris; Kuipers, Norbert J.M.; Haan, de Andre B.; Kwant, Gerard

    2007-01-01

    A combination of using an aqueous solution of sodium hydrogen carbonate for forward-extraction of carboxylic acids from a dilute apolar organic solvent, and carbon dioxide under pressure for its back-recovery, is studied. Used in combination, these two steps might provide a technique for the recover

  14. Bach Adsorption Study for the Extraction of Silver Ions by Hydrazone Compounds from Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Abdussalam Salhin Mohamad Ali

    2012-01-01

    Full Text Available Sorbent materials based on a hydrazone Schiff base compound, C14H11BrN4O4, were prepared either by immobilizing the ligand into sol-gel (SG1 or bonding to silica (SG2. The sorbent materials were characterized by FT-IR, EDX, SEM, TEM, and TGA. The sorption characteristics of a matrix of eight transition metal ions (Ag+, Cu2+, Co2+, Ni2+, Fe3+, Pb2+, Zn2+, and Mn2+ using batch method were studied. Several key parameters that affected the extraction efficiency such as pH, contact time, metal ions concentration, and gel size (for SGl were investigated and optimized. Under the optimized conditions, the physically immobilized hydrazone sorbent (SG1 exhibits highest selectivity towards Ag+ ions, while the chemically bonded hydrazone sorbent (SG2 exhibits high extraction for all metal ions tested. However, for practical applications such as the removal and preconcentration of Ag+, the physically immobilized sorbent (SG1 is preferred.

  15. Efficient and eco-friendly extraction of corn germ oil using aqueous ethanol solution assisted by steam explosion.

    Science.gov (United States)

    Ni, Shuangshuang; Zhao, Wei; Zhang, Yiqi; Gasmalla, Mohammed A A; Yang, Ruijin

    2016-04-01

    An improved aqueous extraction method has been established for extraction of oil from corn germs. This method primarily included steam explosion pretreatment and aqueous ethanol extraction. Process variables such as steam pressure, resident time, particle size and ethanol concentration were investigated. The highest yield of 93.74 % was obtained when ground steam-exploded corn germ (1.3 MPa, 30 s, 30-35 μm particle size) was treated with 30 % (v/v) aqueous ethanol for 2 h, at 60 °C and pH 9.0. The residual oil content in water and sediment phase decreased dramatically to 4 % and 3 %, respectively. The enhancement mechanism of the process induced by steam explosion was analyzed by confocal laser scanning microscope (CLSM). The quality of extracted crude oil was also investigated. The results showed that the quality of extracted oil was superior to commercial oils.

  16. Mild extraction methods using aqueous glucose solution for the analysis of natural dyes in textile artefacts dyed with Dyer's madder (Rubia tinctorum L.).

    Science.gov (United States)

    Ford, Lauren; Henderson, Robert L; Rayner, Christopher M; Blackburn, Richard S

    2017-03-03

    Madder (Rubia tinctorum L.) has been widely used as a red dye throughout history. Acid-sensitive colorants present in madder, such as glycosides (lucidin primeveroside, ruberythric acid, galiosin) and sensitive aglycons (lucidin), are degraded in the textile back extraction process; in previous literature these sensitive molecules are either absent or present in only low concentrations due to the use of acid in typical textile back extraction processes. Anthraquinone aglycons alizarin and purpurin are usually identified in analysis following harsh back extraction methods, such those using solvent mixtures with concentrated hydrochloric acid at high temperatures. Use of softer extraction techniques potentially allows for dye components present in madder to be extracted without degradation, which can potentially provide more information about the original dye profile, which varies significantly between madder varieties, species and dyeing technique. Herein, a softer extraction method involving aqueous glucose solution was developed and compared to other back extraction techniques on wool dyed with root extract from different varieties of Rubia tinctorum. Efficiencies of the extraction methods were analysed by HPLC coupled with diode array detection. Acidic literature methods were evaluated and they generally caused hydrolysis and degradation of the dye components, with alizarin, lucidin, and purpurin being the main compounds extracted. In contrast, extraction in aqueous glucose solution provides a highly effective method for extraction of madder dyed wool and is shown to efficiently extract lucidin primeveroside and ruberythric acid without causing hydrolysis and also extract aglycons that are present due to hydrolysis during processing of the plant material. Glucose solution is a favourable extraction medium due to its ability to form extensive hydrogen bonding with glycosides present in madder, and displace them from the fibre. This new glucose method offers an

  17. Extraction and preconcentration of selenium from aqueous solutions and its determination in water and hair samples by atomic-absorption spectrophotometry.

    Science.gov (United States)

    Ejaz, M; Qureshi, M A

    1987-03-01

    Several organic solvents, including benzene, xylene, toluene, nitrobenzene, chloroform, carbon tetrachloride, chlorobenzene and high molecular-weight pyridines such as 4-(5-nonyl)pyridine, 2-hexyl-pyridine and benzylpyridine have been investigated as components of systems for the extraction and preconcentration of selenium from nitric acid solutions containing iodide. The results are discussed in terms of choice of reagents and the acid and iodide concentrations, and of several other parameters affecting the extraction. The utility of the method for separation of selenium from aqueous solution has been evaluated. The method has been used for preconcentration of trace levels of selenium from water and hair samples for determination by atomic-absorption spectrophotometry.

  18. 2010 Water & Aqueous Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Dor Ben-Amotz

    2010-08-13

    Water covers more than two thirds of the surface of the Earth and about the same fraction of water forms the total mass of a human body. Since the early days of our civilization water has also been in the focus of technological developments, starting from converting it to wine to more modern achievements. The meeting will focus on recent advances in experimental, theoretical, and computational understanding of the behavior of the most important and fascinating liquid in a variety of situations and applications. The emphasis will be less on water properties per se than on water as a medium in which fundamental dynamic and reactive processes take place. In the following sessions, speakers will discuss the latest breakthroughs in unraveling these processes at the molecular level: Water in Solutions; Water in Motion I and II; Water in Biology I and II; Water in the Environment I and II; Water in Confined Geometries and Water in Discussion (keynote lecture and poster winners presentations).

  19. Preparation and application of polymer inclusion membranes (PIMs) including alamine 336 for the extraction of metals from an aqueous solution: Priprava in uporaba membrane iz polimera (PIM) in alamina 336 za ločenje kovin iz vodnih raztopin:

    OpenAIRE

    2014-01-01

    Polymer inclusion membranes (PIMs) present an attractive approach for the separation of metals from an aqueous solution. The present study is about the application of Alamine 336 as an ion carrier in PIMs. The separation of copper (II), cobalt (II), nickel (II) and cadmium (II) from aqueous solutions with polymer inclusion membranes was investigated. PIMs are formed by casting a solution containing a carrier (extractant), a plasticizer and a base polymer, such as cellulose tri-acetate (CTA) o...

  20. Determination of organophosphorus flame retardants in fish by pressurized liquid extraction using aqueous solutions and solid-phase microextraction coupled with gas chromatography-flame photometric detector.

    Science.gov (United States)

    Gao, Zhanqi; Deng, Yuehua; Yuan, Wenting; He, Huan; Yang, Shaogui; Sun, Cheng

    2014-10-31

    A novel method was developed for the determination of organophosphorus flame retardants (PFRs) in fish. The method consists of a combination of pressurized liquid extraction (PLE) using aqueous solutions and solid-phase microextraction (SPME), followed by gas chromatography-flame photometric detector (GC-FPD). The experimental parameters that influenced extraction efficiency were systematically evaluated. The optimal responses were observed by extracting 1g of fish meat with the solution of water:acetonitrile (90:10, v/v) at 150°C for 5min and acid-washed silica gel used as lipid sorbent. The obtained extract was then analyzed by SPME coupled with GC-FPD without any additional clean-up steps. Under the optimal conditions, the proposed procedure showed a wide linear range (0.90-5000ngg(-1)) obtained by analyzing the spiked fish samples with increasing concentrations of PFRs and correlation coefficient (R) ranged from 0.9900 to 0.9992. The detection limits (S/N=3) were in the range of 0.010-0.208ngg(-1) with standard deviations (RSDs) ranging from 2.0% to 9.0%. The intra-day and inter-day variations were less than 9.0% and 7.8%, respectively. The proposed method was successfully applied to the determination of PFRs in real fish samples with recoveries varying from 79.8% to 107.3%. The results demonstrate that the proposed method is highly effective for analyzing PFRs in fish samples.

  1. AQUEOUS BIPHASE EXTRACTION FOR PROCESSING OF FINE COAL

    Energy Technology Data Exchange (ETDEWEB)

    K. Osseo-Asare; X. Zeng

    2002-01-01

    The objective of this research project is to develop an aqueous biphase extraction process for the treatment of fine coals. Aqueous biphase extraction is an advanced separation technology that relies on the ability of an aqueous system consisting of a water-soluble polymer and another component, e.g., another polymer, an inorganic salt, or a nonionic surfactant, to separate into two immiscible aqueous phases. The principle behind the partition of solid particles in aqueous biphase systems is the physicochemical interaction between the solid surface and the surrounding liquid solution. In order to remove sulfur and mineral matter from fine coal with aqueous biphasic extraction, it is necessary to know the partitioning behavior of coal, as well as the inorganic mineral components. Therefore, in this research emphasis was placed on the partitioning behavior of fine coal particles as well as model fine inorganic particles in aqueous biphase systems.

  2. Kinetic Study of Copper(II Simultaneous Extraction/Stripping from Aqueous Solutions by Bulk Liquid Membranes Using Coupled Transport Mechanisms

    Directory of Open Access Journals (Sweden)

    Loreto León

    2016-09-01

    Full Text Available Heavy metals removal/recovery from industrial wastewater has become a prime concern for both economic and environmental reasons. This paper describes a comparative kinetic study of the removal/recovery of copper(II from aqueous solutions by bulk liquid membrane using two types of coupled facilitated transport mechanisms and three carriers of different chemical nature: benzoylacetone, 8-hydroxyquinoline, and tri-n-octylamine. The results are analyzed by means of a kinetic model involving two consecutive irreversible first-order reactions (extraction and stripping. Rate constants and efficiencies of the extraction (k1, EE and the stripping (k2, SE reactions, and maximum fluxes through the membrane, were determined for the three carriers to compare their efficiency in the Cu(II removal/recovery process. Counter-facilitated transport mechanism using benzoylacetone as carrier and protons as counterions led to higher maximum flux and higher extraction and stripping efficiencies due to the higher values of both the extraction and the stripping rate constants. Acceptable linear relationships between EE and k1, and between SE and k2, were found.

  3. Extraction of uranyl nitrate, sulphate and chloride with tri-n-octyl amine (TOA from aqueous solutions

    Directory of Open Access Journals (Sweden)

    DJORDJE M. PETKOVIC

    2001-07-01

    Full Text Available Extraction of uranyl nitrate, chloride and sulphate with tri-n-octyl amine (TOA in benzene as a function of the TOA concentration has been studied. The concentration based extraction equilibrium constants were calculated from the distribution data of the uranyl salts, fitting the parameters of a chemical model to the experimentally obtained extraction isotherms. The calculated equilibrium constants are 46.5, 89.4 and 4.2·104 for uranyl nitrate, chloride and sulphate, respectively. These values are in good agreement with the previously reported extraction equilibrium constants calculated by the inflection point method.

  4. Extraction and separation of titanium(IV with D2EHPA and PC-88A from aqueous perchloric acid solutions

    Directory of Open Access Journals (Sweden)

    PURSHOTTAM M. DHADKE

    2002-07-01

    Full Text Available The liquid-liquid extraction of Ti(IV from perchlorate media using, di(2-ethylhexyl phosphoric acid (D2EHPA and 2-ethylhexyl prosphonic acid mono-2-ethylhexyl ester (PC-88A in toluene as the extractant was studied. Quantitative extraction of Ti(IV was observed in the lower acidity range of 0.01 to 0.1 mol dm-3 with 0.003 mol dm-3 D2EHPA and 0.01 mol dm-3 PC-88A in toluene, respectively, and in the higher acidity range of 9.0 to 10.0 mol dm-3 with 0.1 mol dm-3 D2EHPA and PC-88A in toluene. Ti(IV was completely stripped from the metal loaded organic phase of both the extractants with 3 % H2O2 in 1 M H2SO4 and determined spectrophotometrically. The stoichiometry of the extracted species was determined on the basis of slope analysis. The extraction in the lower acidity range was found to proceed by a cation-exchange mechanism with the extracted species being TiOR2·2HR, while in the higher acidity range it was by solvation with the extracted species being Ti(OH3ClO4·4HR. Separation of Ti(IV was also carried out from some associated metals like Fe(III, Al(III, V(V, Ce(IV, Mg(II and Mn(II. The developed methods were extended for the determination of Ti(IV in real samples like ilmenite, magnetite and red mud in order to show the practical utility of the extractants.

  5. Allelopathic Potential of Cucumber Tissues Aqueous Extracts

    Institute of Scientific and Technical Information of China (English)

    DONG Lin-lin; HAO Zhi-peng; ZUO Yuan-mei; LI Xiao-lin; WANG Qian

    2011-01-01

    [ Objective] The aim of this study was to explore allelopathic effects of the water-extracted crude of cucumber plant parts on seed germination and seedling growth of lettuce ( Lactuca sativa L. ), cabbage ( Brassica pekinensis L. ), radish ( Raphanus sativus L. ) and scallion ( Allium fistulosum L. ). [ Method] The allelopathic effects of different cucumber tissues aqueous extracts were investigated on lettuce, cabbage,radish and scallion using the water-soluble allelopathic principle by seedling bioassay tests. [ Result] The trends of inhibitory effects of different cucumber parts increased with increasing extract concentrations. The inhibition effects and the inhibition rate of three aqueous extracts were more significant on root growth than shoot length. Leaf aqueous extracts represented the most exhibited and root aqueous extracts representing the least inhibitory on seed germination, shoot length and root length of lettuce, cabbage, radish and scallion. [Conclusion] This study had provided basis for allelopathic character of different cucumber plant parts.

  6. Stabilization of a magnetic nano-adsorbent by extracted pectin to remove methylene blue from aqueous solution: A comparative studying between two kinds of cross-likened pectin

    Energy Technology Data Exchange (ETDEWEB)

    Rakhshaee, Roohan, E-mail: rakhshaei@iaurasht.ac.ir [Department of Applied Chemistry, Faculty of Science, Islamic Azad University, Rasht Branch, P.O. Box 41335-3516, Rasht (Iran, Islamic Republic of); Panahandeh, Mohammad [Environmental Research Institute of Jahad Daneshgahi (Iran, Islamic Republic of)

    2011-05-15

    The removal of methylene blue (MB) as a cationic dye from aqueous solution by the stabilized Fe{sub 3}O{sub 4} nano-particles with the extracted pectin from apple waste (FN-PA) increased due to using the cross-linked forms of the bound pectin on the nano-particles surface by glutaraldehyde (FN-PAG) and adipic acid (FN-PAA) as the cross-linking agents. This increase happened in spite of binding some of the adsorbent functional groups of pectin with nano-particles. It can be due to the local concentrate of other free functional groups after connecting with nano-scale particles. Thermodynamic studies showed that the adsorption equilibrium constant and the maximum adsorption capacities increased with increasing temperature for all of the nano-bioparticles. The kinetic followed the second-order models with the highest rate constants viz. 16.23, 19.76 and 23.04 (x10{sup -3} g/mg min) by FN-PAA. The adsorption force arrangement of MB by these nano-biosorbents regarding their activation energy was obtained as: FN-PAA > FN-PAG > FN-PA.

  7. Process for the extraction of strontium from acidic solutions

    Energy Technology Data Exchange (ETDEWEB)

    Horwitz, E.P.; Dietz, M.L.

    1993-01-01

    The invention is a process for selectively extracting strontium values from aqueous nitric acid waste solutions containing these and other fission product values. The extractant solution is a macrocyclic polyether in an aliphatic hydrocarbon diluent containing a phase modifier. The process will selectively extract strontium values from nitric acid solutions which are up to 6 molar in nitric acid.

  8. Terahertz absorption of dilute aqueous solutions.

    Science.gov (United States)

    Heyden, Matthias; Tobias, Douglas J; Matyushov, Dmitry V

    2012-12-21

    Absorption of terahertz (THz) radiation by aqueous solutions of large solutes reports on the polarization response of their hydration shells. This is because the dipolar relaxation of the solute is dynamically frozen at these frequencies, and most of the solute-induced absorption changes, apart from the expulsion of water, are caused by interfacial water. We propose a model expressing the dipolar response of solutions in terms of a single parameter, the interface dipole moment induced in the interfacial water by electromagnetic radiation. We apply this concept to experimental THz absorption of hydrated sugars, amino acids, and proteins. None of the solutes studied here follow the expectations of dielectric theories, which predict a negative projection of the interface dipole on the external electric field. We find that this prediction is not able to describe the available experimental data, which instead suggests a nearly zero interface dipole for sugars and a more diverse pattern for amino acids. Hydrophobic amino acids, similarly to sugars, give rise to near zero interface dipoles, while strongly hydrophilic ones are best described by a positive projection of the interface dipole on the external field. The sign of the interface dipole is connected to the slope of the absorption coefficient with the solute concentration. A positive slope, implying an increase in the solution polarity relative to water, mirrors results frequently reported for protein solutions. We therefore use molecular dynamics simulations of hydrated glucose and lambda repressor protein to calculate the interface dipole moments of these solutes and the concentration dependence of the THz absorption. The absorption at THz frequencies increases with increasing solute concentration in both cases, implying a higher polarity of the solution compared to bulk water. The structure of the hydration layer, extracted from simulations, is qualitatively similar in both cases, with spatial correlations

  9. Calorimetric studies of macromolecular aqueous solutions

    NARCIS (Netherlands)

    Blandamer, M.J; Cullis, P.M.; Engberts, J.B.F.N.

    1996-01-01

    Both titration and differential scanning microcalorimetric techniques are shown to yield important information concerning the properties of macromolecules in aqueous solution. Application of titration calorimetry is examined in me context of deaggregation of canonic micelles (e.g. hexadecyltrimethyl

  10. Development of Solid-Phase Extraction Using Molecularly Imprinted Polymer for the Analysis of Organophosphorus Pesticides-(Chlorpyrifos) in Aqueous Solution

    OpenAIRE

    Binsalom, A.; Chianella, I.; Campbell, K.; Zourob, M.

    2016-01-01

    A new and selective sorbent for molecularly imprinted solid-phase extraction (MISPE) was prepared to extract chlorpyrifos (CPF) residue from solutions. The extracted analyte was analyzed by high performance liquid chromotography (HPLC) coupled with photodiode array detection. To synthesize the molecularly imprinted polymers, four different pyrogens (acetonitrile, toluene, dichloromethane and chloroform) were initially studied. CPF was used as the template molecule, methacrylic acid as the fun...

  11. Simultaneous Separation of Manganese, Cobalt, and Nickel by the Organic-Aqueous-Aqueous Three-Phase Solvent Extraction

    Science.gov (United States)

    Shirayama, Sakae; Uda, Tetsuya

    2016-04-01

    This research outlines an organic-aqueous-aqueous three-phase solvent extraction method and proposes its use in a new metal separation process for the recycling of manganese (Mn), cobalt (Co), and nickel (Ni) from used lithium ion batteries (LIBs). The three-phase system was formed by mixing xylene organic solution, 50 pct polyethylene glycol (PEG) aqueous solution, and 1 mol L-1 sodium sulfate (Na2SO4) aqueous solution. The xylene organic solution contained 2-ethylhexylphosphonic acid (D2EHPA) as an extractant for Mn ion, and the Na2SO4 aqueous solution contained 1 mol L-1 potassium thiocyanate (KSCN) as an extractant for Co ion. Concentrations of the metal ions were varied by dissolving metal sulfates in the Na2SO4 aqueous solution. As a result of the experiments, Mn, Co, and Ni ions were distributed in the xylene organic phase, PEG-rich aqueous phase, and Na2SO4-rich aqueous phase, respectively. The separation was effective when the pH value was around 4. Numerical simulation was also conducted in order to predict the distribution of metal ions after the multi-stage counter-current extractions.

  12. Precipitation of neptunium dioxide from aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, K E

    1999-12-01

    Tens of thousands of metric tons of highly radioactive, nuclear waste have been generated in the US. Currently, there is no treatment or disposal facility for these wastes. Of the radioactive elements in high-level nuclear waste, neptunium (Np) is of particular concern because it has a long half-life and may potentially be very mobile in groundwaters associated with a proposed underground disposal site at Yucca Mountain, Nevada. Aqueous Np concentrations observed in previous, short-term solubility experiments led to calculated potential doses exceeding proposed long-term regulatory limits. However, thermodynamic data for Np at 25 C showed that these observed aqueous Np concentrations were supersaturated with respect to crystalline NpO{sub 2}. It was hypothesized that NpO{sub 2} is the thermodynamically stable solid phase in aqueous solution, but it is slow to form in an aqueous solution of NpO{sub 2}{sup +} on the time scale of previous experiments. The precipitation of NpO{sub 2} would provide significantly lower aqueous Np concentrations leading to calculated doses below proposed regulatory limits. To test this hypothesis, solubility experiments were performed at elevated temperature to accelerate any slow precipitation kinetics. Ionic NpO{sub 2}{sup +} (aq) was introduced into very dilute aqueous solutions of NaCl with initial pH values ranging from 6 to 10. The reaction vessels were placed in an oven and allowed to react at 200 C until steady-state aqueous Np concentrations were observed. In all cases, aqueous Np concentrations decreased significantly from the initial value of 10{sup {minus}4} M. The solids that formed were analyzed by x-ray powder diffraction, x-ray absorption spectroscopy, and scanning electron microscopy. The solids were determined to be high-purity crystals of NpO{sub 2}. This is the first time that crystalline NpO{sub 2} has been observed to precipitate from NpO{sub 2}{sup +}(aq) in near-neutral aqueous solutions. The results obtained

  13. Layer-by-layer encapsulated nano-emulsion of ionic liquid loaded with functional material for extraction of Cd(2+) ions from aqueous solutions.

    Science.gov (United States)

    Elizarova, Iuliia S; Luckham, Paul F

    2017-04-01

    Ionic liquids can serve as an environmentally-friendly replacement for solvents in emulsions, therefore they are considered suitable to be used as an emulsified medium for various active materials one of which are extractors of metal ions. Increasing the extraction efficiency is considered to be one of the key objectives when working with such extraction systems. One way to improve the extraction efficiency is to increase the contact area between the extractant and the working ionic solution. This can be accomplished by creating a nano-emulsion of ionic liquid containing such an extractant. Since emulsification of ionic liquid is not always possible in the sample itself, there is a necessity of creating a stable emulsion that can be added externally and on demand to samples from which metal ions need to be extracted. We propose a method of fabrication of a highly-stable extractant-loaded ionic liquid-in-water nano-emulsion via a low-energy phase reversal emulsification followed by continuous layer-by-layer polyelectrolyte deposition process to encapsulate the nano-emulsion and enhance the emulsion stability. Such a multilayered stabilized nano-emulsion was tested for extraction of Cd(2+) and Ca(2+) ions in order to determine its extraction efficiency and selectivity. It was found to be effective in the extraction of Cd(2+) ions with near 100% cadmium removal, as well as being selective since no Ca(2+) ions were extracted. The encapsulated emulsion was removed from samples post-extraction using two methods - filtration and magnetic separation, both of which were shown to be viable under different circumstances - larger and mechanically stronger capsules could be removed by filtration, however magnetic separation worked better for both smaller and bigger capsules. The long-term stability of nano-emulsion was also tested being a very important characteristic for its proposed use: it was found to be highly stable after four months of storage time.

  14. Hydrophobic Solvation: Aqueous Methane Solutions

    Science.gov (United States)

    Konrod, Oliver; Lankau, Timm

    2007-01-01

    A basic introduction to concept of a solvation shell around an apolar solute as well as its detection is presented. The hydrophobic solvation of toluene is found to be a good teaching example which connects macroscopic, phenomenological thermodynamic results with an atomistic point of view.

  15. Enzymatic Aqueous Extraction of Soybean Oil

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The procedure of enzymatic aqueous extraction of soybean oil was assessed when two-step controlled enzymatic hydrolysis was applied. With aqueous extraction of soybean oil-containing protein, the highest yield of oil was 96.1% at the optimized conditions studied. Soybean oil-containing protein was hydrolyzed and resulted in releasing part of oil. The separated protein that contained 40% oil was enriched due to its adsorption capacity of released oil, the average oil extraction yeild reached 93.5%. Then the high oil content protein was hydrolyzed again to release oil by enzyme, the oil extraction yeild was 80.4%. As a result, high quality of soybean oil was obtained and the content of total oil yield was 74.4%.

  16. Separation of uranium from aqueous solutions using calix[6]arenes in liquid-liquid extraction as well as solid phase extraction; Abtrennung von Uran aus waessriger Loesung durch Calix[6]arene mittels Fluessig-Fluessig-Extraktion sowie Festphasen-Extraktion

    Energy Technology Data Exchange (ETDEWEB)

    Schmeide, K.; Geipel, G.; Bernhard, G.

    2004-11-01

    The suitability of different calyx[n] arene types for uranyl extraction from liquid solutions was examined by means of liquid-liquid extraction using aqueous phases and organic solvents of varying compositions. It was found that COOH-derivatised calyx[6] arenes have good extraction properties and can even be used in the acid pH range. The use of calixarene-modified fleeces for the separation of uranyl from aqueous phases was examined in batch experiments with pH and uranyl concentration as variables and in the presence or absence of competing ions. The results showed that calixarene-modified fleeces can be used for uranium separation starting from pH 4. At pH 5, up to a maximum of 7.6 x 10{sup -7} mol uranium can be bound per 1 g of calixarene-modified fleece. The separation of uranyl from synthetic pit waters was examined as a means of testing the separation capacity of calixarene-modified fleeces in environmentally sensitive waters. Studies on the reversibility of uranium bonding to calixarene-treated polyester fleeces have shown that under environmentally realistic conditions (neutral pH range) the uranium is firmly bound to the calixarene-modified fleeces and cannot be mobilised. By contrast, in acidic environments calixarene-modified fleeces are capable of near-complete regeneration. Such regenerated textile filter materials can then be used for further uranium separation cycles. [German] Die Eignung verschiedener Calix[n]aren-Typen fuer die Uranylextraktion aus waessriger Loesung wurde mittels Fluessig-Fluessig-Extraktion unter Variation der Zusammensetzung der waessrigen Phase und des organischen Loesungsmittels untersucht. Es konnte gezeigt werden, dass COOH-derivatisierte Calix[6]arene gute Extraktionseigenschaften aufweisen und selbst im sauren pH-Bereich angewendet werden koennen. Die Uranylabtrennung aus waessriger Loesung durch calixarenmodifizierte Vliese wurde in Abhaengigkeit des pH-Wertes und der Uranylkonzentration in Abwesenheit und Gegenwart von

  17. Aqueous Solution Chemistry on Mars

    Science.gov (United States)

    Quinn, R.; Hecht, M.; Kounaves, S.; Young, S.; West, S.; Fisher, A.; Grunthaner, P.

    2007-12-01

    Currently en route to Mars, the Phoenix mission carries four wet chemistry cells designed to perform basic solution chemistry on martian soil. The measurement objectives are typical of those that would be performed on an unknown sample on Earth, including detection of common anions and cations, total conductivity, pH, redox potential, cyclic voltammetry (CV), etc. Both the challenge and the novelty arise from the necessity to perform these measurements with severely constrained resources in a harsh and (literally) alien environment. Sensors for all measurements are integrated into a common "beaker," with the ability to perform a two-point calibration of some sensors using a pair of low-concentration solutions. Sulfate measurement is performed with a crude titration. While most measurements use ion selective electrodes, halide interferences are resolved by independent chronopotentiometry (CP) measurements. No preconditioning of the soil-water mixture is possible, nor is any physical characterization of the introduced soil sample beyond coarse visual inspection. Among the idiosyncrasies of the measurement is the low external pressure, which requires that the analysis be performed close to the boiling point of water under an atmosphere consisting almost entirely of water vapor. Despite these liabilities, however, extensive laboratory characterization has validated the basic approach, and protocols for both CV and CP have been developed and tested. Enhancing the value of the measurement is the suite of coordinated observations, such as microscopy and evolved gas analysis, to be performed by other Phoenix instruments.

  18. Water & Aqueous Solutions. Final Progress Report

    Energy Technology Data Exchange (ETDEWEB)

    None

    2002-08-09

    The Gordon Research Conference (GRC) on Water & Aqueous Solutions was held at Holderness School, New Hampshire, 8/4/02 thru 8/9/02. Emphasis was placed on current unpublished research and discussion of the future target areas in this field.

  19. Actinide recovery using aqueous biphasic extraction: Initial developmental studies

    Energy Technology Data Exchange (ETDEWEB)

    Chaiko, D.J.; Mensah-Biney, R.; Mertz, C.J.; Rollins, A.N.

    1992-08-01

    Aqueous biphasic extraction systems are being developed to treat radioactive wastes. The separation technique involves the selective partitioning of either solutes or colloid-size particles between two scible aqueous phases. Wet grinding of plutonium residues to an average particle size of one micron will be used to liberate the plutonium from the bulk of the particle matrix. The goal is to produce a plutonium concentrate that will integrate with existing and developing chemical recovery processes. Ideally, the process would produce a nonTRU waste stream. Coupling physical beneficiation with chemical processing will result in a substantial reduction in the volume of mixed wastes generated from dissolution recovery processes. As part of this program, we will also explore applications of aqueous biphasic extraction that include the separation and recovery of dissolved species such as metal ions and water-soluble organics. The expertise and data generated in this work will form the basis for developing more cost-effective processes for handling waste streams from environmental restoration and waste management activities within the DOE community. This report summarizes the experimental results obtained during the first year of this effort. Experimental efforts were focused on elucidating the surface and solution chemistry variables which govern partitioning behavior of plutonium and silica in aqueous biphasic extraction systems. Additional efforts were directed toward the development of wet grinding methods for producing ultrafine particles with diameters of one micron or less.

  20. Water-compatible dummy molecularly imprinted resin prepared in aqueous solution for green miniaturized solid-phase extraction of plant growth regulators.

    Science.gov (United States)

    Wang, Mingyu; Chang, Xiaochen; Wu, Xingyu; Yan, Hongyuan; Qiao, Fengxia

    2016-08-01

    A water-compatible dummy molecularly imprinted resin (MIR) was synthesized in water using melamine, urea, and formaldehyde as hydrophilic monomers of co-polycondensation. A triblock copolymer (PEO-PPO-PEO, P123) was used as porogen to dredge the network structure of MIR, and N-(1-naphthyl) ethylenediamine dihydrochloride, which has similar shape and size to the target analytes, was the dummy template of molecular imprinting. The obtained MIR was used as the adsorbent in a green miniaturized solid-phase extraction (MIR⬜mini-SPE) of plant growth regulators, and there was no organic solvent used in the entire MIR⬜mini-SPE procedure. The calibration linearity of MIR⬜mini-SPE⬜HPLC method was obtained in a range 5⬜250ngmL(↙1) for IAA, IPA, IBA, and NAA with correlation coefficient (r) Ⱕ0.9998. Recoveries at three spike levels are in the range of 87.6⬜100.0% for coconut juice with relative standard deviations Ⱔ8.1%. The MIR⬜mini-SPE method possesses the advantages of environmental friendliness, simple operation, and high efficiency, so it is potential to apply the green pretreatment strategy to extraction of trace analytes in aqueous samples.

  1. Synergistic Extraction of Gallium for Sulfate Solution

    Institute of Scientific and Technical Information of China (English)

    DENGTong; HUANGLijuan; 等

    2002-01-01

    A novel extractant mixture, di-2-ethylhexyl phosphate (DEHPA) plus HX, was propose and tested for recovering gallium from sulfate solution.It was found that the extraction capacity of DEPHA for gallium from sulfate solution could be enhanced significantly due to the synergistic effect of acidix extractant HX. Gallium extraction is negligible below pH 0 and highly sensitive to pH of aqueous phase in the range from 0 to 1, and satisfactory extraction can be gained at pH>1. More than 96% Ga extraction was obtained using 15% DEHPA plus 2% HX. Although Fe(Ⅲ) was found to be extracted preferentially to Ga (Ⅲ), effective extraction of Ga (Ⅲ) was possible by reducing ferric to the ferrous state prior to extraction. A loaded organic phase containing 0.48g·L-1 Ga could be produced from solution of 0.12g·L-1 Ga at A/O ratio of 4:1 via three mixer-settler operation stages. Gallium was stripped quantitatively from the loaded organic phase with 1.5mol·L-1 of sulfuric acid.

  2. Removal of phenols from aqueous solutions by emulsion liquid membranes.

    Science.gov (United States)

    Reis, M Teresa A; Freitas, Ondina M F; Agarwal, Shiva; Ferreira, Licínio M; Ismael, M Rosinda C; Machado, Remígio; Carvalho, Jorge M R

    2011-09-15

    The present study deals with the extraction of phenols from aqueous solutions by using the emulsion liquid membranes technique. Besides phenol, two derivatives of phenol, i.e., tyrosol (2-(4-hydroxyphenyl)ethanol) and p-coumaric acid (4-hydroxycinnamic acid), which are typical components of the effluents produced in olive oil plants, were selected as the target solutes. The effect of the composition of the organic phase on the removal of solutes was examined. The influence of pH of feed phase on the extraction of tyrosol and p-coumaric was tested for the membrane with Cyanex 923 as an extractant. The use of 2% Cyanex 923 allowed obtaining a very high extraction of phenols (97-99%) in 5-6 min of contact time for either single solute solutions or for their mixtures. The removal efficiency of phenol and p-coumaric acid attained equivalent values by using the system with 2% isodecanol, but the removal rate of tyrosol was found greatly reduced. The extraction of tyrosol and p-coumaric acid from their binary mixture was also analysed for different operating conditions like the volume ratio of feed phase to stripping phase (sodium hydroxide), the temperature and the initial concentration of solute in the feed phase.

  3. Extraction and Chromatographic Determination of Shikimic Acid in Chinese Conifer Needles with 1-Benzyl-3-methylimidazolium Bromide Ionic Liquid Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Fengli Chen

    2014-01-01

    Full Text Available An ionic liquids-based ultrasound-assisted extraction (ILUAE method was successfully developed for extracting shikimic acid from conifer needles. Eleven 1-alkyl-3-methylimidazolium ionic liquids with different cations and anions were investigated and 1-benzyl-3-methylimidazolium bromide solution was selected as the solvent. The conditions for ILUAE, including the ionic liquid concentration, ultrasound power, ultrasound time, and liquid-solid ratio, were optimized. The proposed method had good recovery (99.37%–100.11% and reproducibility (RSD, n = 6; 3.6%. ILUAE was an efficient, rapid, and simple sample preparation technique that showed high reproducibility. Based on the results, a number of plant species, namely, Picea koraiensis, Picea meyeri, Pinus elliottii, and Pinus banksiana, were identified as among the best resources of shikimic acid.

  4. Zeolites as alcohol adsorbents from aqueous solutions

    Directory of Open Access Journals (Sweden)

    Cekova Blagica

    2006-01-01

    Full Text Available The potential usage of zeolites as adsorbents for the removal of organic molecules from water was investigated in a series of experiments with aqueous solutions of lower alcohols. This could represent a simple solution to the problem of cleaning up industrial wastewater as well as recovering valuable chemicals at relatively low costs. Adsorption isotherms of the Langmuir type were applied, and calculations showed that the amount of propanol adsorbed on silicalite corresponded to approximately 70% of the pore volume. The adsorption process is simple, and recovery of the more concentrated products is easily done by heat treatment and/or at lowered pressures. Adsorption experiments with aqueous acetone showed that silicalite had approximately the same adsorption capacity for acetone as for n-propanol. Heats of adsorption were determined calorimetrically.

  5. Aqueous solution dispersement of carbon nanotubes

    Science.gov (United States)

    Kim, Jae-Woo (Inventor); Park, Cheol (Inventor); Choi, Sang H. (Inventor); Lillehei, Peter T. (Inventor); Harrison, Joycelyn S. (Inventor)

    2011-01-01

    Carbon nanotubes (CNTs) are dispersed in an aqueous buffer solution consisting of at least 50 weight percent water and a remainder weight percent that includes a buffer material. The buffer material has a molecular structure defined by a first end, a second end, and a middle disposed between the first and second ends. The first end is a cyclic ring with nitrogen and oxygen heteroatomes, the middle is a hydrophobic alkyl chain, and the second end is a charged group.

  6. Partitioning of U, Np, Th, and Eu between acidic aqueous Al(NO3)3 solutions and various TOPO extraction chromatographic materials

    Science.gov (United States)

    Shafer, Jenifer C.; Sulakova, Jana; Ogden, Mark D.; Nash, Kenneth L.

    2010-03-01

    As the Hanford site undergoes remediation, it is noted that significant economies could be realized by minimizing the amount of aluminum deposited in High-Level Waste glass. Though such a step is not planned, an acidic scrub of the Hanford sludge could enhance Al removal. It is likely that the resulting Al(NO3)3 solution would contain measurable amounts of transuranic elements, thus the solution might require some secondary treatment to remove TRU contamination. Thus far, extraction chromatography (EXC) has shown promise [1] as an alternative to a liquid-liquid remediation of the Hanford site. Previous EXC studies have shown >99% of the Eu can be extracted from simulated Al/Cr waste. This study continues an examination of a hypothetical secondary cleanup of the waste by studying the removal of UO22+, NpO2+, NpO22+ and Th4+ from using tri-n-octyl phospine oxide (TOPO) impregnated XAD7 resins. Neptunium was held in the V and VI oxidation states using ascorbic acid and chromate, respectively. Initial results show extraction following classical metal recovery trends, wherein an increased Zeff correlates with increased distribution of the metal into the organic resin phase. The uptake of Eu3+ (representative of An3+) on a column of the same material was also investigated. Uptake kinetics were improved by wetting the TOPO-XAD7 resin with n-dodecane (TOPO-XAD7n). The presence of n-dodecane also provided consistency between batch mode and column mode metal recovery. Preliminary data show >99% recovery of metal ions with a Zeff >= 3 under various simulated conditions.

  7. OPTICAL PROPERTIES OF CARBAMIDE AQUEOUS SOLUTIONS

    Directory of Open Access Journals (Sweden)

    E. V. Avramenko

    2016-03-01

    Full Text Available Subject of Research. The paper presents the results of measurements of refractometric properties (refractive index n, its temperature factor dn/dt and the ultraviolet spectral absorption in carbonic acid diamide aqueous solutions (carbamide depending on solid residue mass fraction md = 0-50 % and on temperaturet = 10-70 °C.Method of Research. Laboratory methods ofliquid-phase medium refractometry and ultraviolet spectrophotometry were applied for the research. We carried out computational modeling of electronic states spectrum for the carbonic acid diamide molecule and theoretical calculation of the fundamental electronic absorption of the molecule in the ultraviolet wavelenght region.Main Results. We have established that the solution concentration md has a nonlinear character and may be represented by the quadratic polynomial with the error Δn= ± 0,0005. We have shown the refractive indexdependence on temperature n(t changes in linear fashion att = 10-70 °C.At that, the inclination of lines n(t increases at the increase of md; so, the temperature factor dn/dt may be approximated by the quadratic polynomial. Transmission spectra of solutions in the spectral region λ= 225-760 nm have no special features except for the sharp edge in the short-wavelength region; the fundamental electronic absorptionis responsible for it. We have established that dispersion dependences of the refraction index n(λ;md in aqueous solutions of carbamide at λ= 360-760 nm and at md = 0-50 % may be calculated with the satisfactory error without additional adjustable parameters from the ultraviolet absorption data in terms of the one-dimentional oscillator Lorentz model.PracticalRelevance. Representedmeasurements of carbonic acid diamide aqueous solutions optical properties may be applied for the adjustment and calibration of commercial refractometers at processing lines of the AdBlue reagent manufacture for the selective catalytic reduction (SCR of motor transport

  8. Density of aqueous solutions of CO2

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, Julio E.

    2001-10-10

    In this report, we present a numerical representation for the partial molar volume of CO2 in water and the calculation of the corresponding aqueous solution density. The motivation behind this work is related to the importance of having accurate representations for aqueous phase properties in the numerical simulation of carbon dioxide disposal into aquifers as well as in geothermal applications. According to reported experimental data the density of aqueous solutions of CO2 can be as much as 2-3% higher than pure water density. This density variation might produce an influence on the groundwater flow regime. For instance, in geologic sequestration of CO2, convective transport mixing might occur when, several years after injection of carbon dioxide has stopped, the CO2-rich gas phase is concentrated at the top of the formation, just below an overlaying caprock. In this particular case the heavier CO2 saturated water will flow downward and will be replaced by water with a lesser CO2 content.

  9. Aqueous enzymatic extraction of Moringa oleifera oil.

    Science.gov (United States)

    Mat Yusoff, Masni; Gordon, Michael H; Ezeh, Onyinye; Niranjan, Keshavan

    2016-11-15

    This paper reports on the extraction of Moringa oleifera (MO) oil by using aqueous enzymatic extraction (AEE) method. The effect of different process parameters on the oil recovery was discovered by using statistical optimization, besides the effect of selected parameters on the formation of its oil-in-water cream emulsions. Within the pre-determined ranges, the use of pH 4.5, moisture/kernel ratio of 8:1 (w/w), and 300stroke/min shaking speed at 40°C for 1h incubation time resulted in highest oil recovery of approximately 70% (goil/g solvent-extracted oil). These optimized parameters also result in a very thin emulsion layer, indicating minute amount of emulsion formed. Zero oil recovery with thick emulsion were observed when the used aqueous phase was re-utilized for another AEE process. The findings suggest that the critical selection of AEE parameters is key to high oil recovery with minimum emulsion formation thereby lowering the load on the de-emulsification step.

  10. Aqueous Solution Vessel Thermal Model Development II

    Energy Technology Data Exchange (ETDEWEB)

    Buechler, Cynthia Eileen [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-10-28

    The work presented in this report is a continuation of the work described in the May 2015 report, “Aqueous Solution Vessel Thermal Model Development”. This computational fluid dynamics (CFD) model aims to predict the temperature and bubble volume fraction in an aqueous solution of uranium. These values affect the reactivity of the fissile solution, so it is important to be able to calculate them and determine their effects on the reaction. Part A of this report describes some of the parameter comparisons performed on the CFD model using Fluent. Part B describes the coupling of the Fluent model with a Monte-Carlo N-Particle (MCNP) neutron transport model. The fuel tank geometry is the same as it was in the May 2015 report, annular with a thickness-to-height ratio of 0.16. An accelerator-driven neutron source provides the excitation for the reaction, and internal and external water cooling channels remove the heat. The model used in this work incorporates the Eulerian multiphase model with lift, wall lubrication, turbulent dispersion and turbulence interaction. The buoyancy-driven flow is modeled using the Boussinesq approximation, and the flow turbulence is determined using the k-ω Shear-Stress-Transport (SST) model. The dispersed turbulence multiphase model is employed to capture the multiphase turbulence effects.

  11. Speciation in aqueous solutions of nitric acid.

    Science.gov (United States)

    Hlushak, S; Simonin, J P; De Sio, S; Bernard, O; Ruas, A; Pochon, P; Jan, S; Moisy, P

    2013-02-28

    In this study, speciation in aqueous solutions of nitric acid at 25 °C was assessed in two independent ways. First, Raman experiments were carried out and interpreted in terms of free nitrate ions, ion pairs and neutral HNO(3) molecules. In parallel, a model was developed to account for the formation of these two kinds of pairs. It was based on an extension of the binding mean spherical approximation (BiMSA), or associative MSA (AMSA), in which the size and the charge of the ions in the chemical pair may differ from those of the free ions. A simultaneous fit of the osmotic coefficient and of the proportion of free ions (obtained from Raman spectroscopy experiments) led to an estimation of the speciation in nitric acid solutions. The result obtained using this procedure was compared with the estimation obtained from the Raman experiments.

  12. Multistep nucleation of nanocrystals in aqueous solution

    Science.gov (United States)

    Loh, N. Duane; Sen, Soumyo; Bosman, Michel; Tan, Shu Fen; Zhong, Jun; Nijhuis, Christian A.; Král, Petr; Matsudaira, Paul; Mirsaidov, Utkur

    2017-01-01

    The nucleation and growth of solids from solutions impacts many natural processes and is fundamental to applications in materials engineering and medicine. For a crystalline solid, the nucleus is a nanoscale cluster of ordered atoms that forms through mechanisms still poorly understood. In particular, it is unclear whether a nucleus forms spontaneously from solution via a single- or multiple-step process. Here, using in situ electron microscopy, we show how gold and silver nanocrystals nucleate from supersaturated aqueous solutions in three distinct steps: spinodal decomposition into solute-rich and solute-poor liquid phases, nucleation of amorphous nanoclusters within the metal-rich liquid phase, followed by crystallization of these amorphous clusters. Our ab initio calculations on gold nucleation suggest that these steps might be associated with strong gold-gold atom coupling and water-mediated metastable gold complexes. The understanding of intermediate steps in nuclei formation has important implications for the formation and growth of both crystalline and amorphous materials.

  13. Aqueous Solutions of Ionic Liquids: Microscopic Assembly.

    Science.gov (United States)

    Vicent-Luna, Jose Manuel; Dubbeldam, David; Gómez-Álvarez, Paula; Calero, Sofia

    2016-02-01

    Aqueous solutions of ionic liquids are of special interest, due to the distinctive properties of ionic liquids, in particular, their amphiphilic character. A better understanding of the structure-property relationships of such systems is hence desirable. One of the crucial molecular-level interactions that influences the macroscopic behavior is hydrogen bonding. In this work, we conduct molecular dynamics simulations to investigate the effects of ionic liquids on the hydrogen-bond network of water in dilute aqueous solutions of ionic liquids with various combinations of cations and anions. Calculations are performed for imidazolium-based cations with alkyl chains of different lengths and for a variety of anions, namely, [Br](-), [NO3](-), [SCN](-) [BF4](-), [PF6](-), and [Tf2N](-). The structure of water and the water-ionic liquid interactions involved in the formation of a heterogeneous network are analyzed by using radial distribution functions and hydrogen-bond statistics. To this end, we employ the geometric criterion of the hydrogen-bond definition and it is shown that the structure of water is sensitive to the amount of ionic liquid and to the anion type. In particular, [SCN](-) and [Tf2N](-) were found to be the most hydrophilic and hydrophobic anions, respectively. Conversely, the cation chain length did not influence the results.

  14. Heterogeneous nucleation of aspartame from aqueous solutions

    Science.gov (United States)

    Kubota, Noriaki; Kinno, Hiroaki; Shimizu, Kenji

    1990-03-01

    Waiting times, the time from the instant of quenching needed for a first nucleus to appear, were measured at constant supercoolings for primary nucleation of aspartame (α-L-aspartyl-L-phenylalanine methylester) from aqueous solutions, which were sealed into glass ampoules (solution volume = 3.16 cm 3). Since the waiting time became shorter by filtering the solution prior to quenching, the nucleation was concluded to be heterogeneously induced. The measured waiting time consisted of two parts: time needed for the nucleus to grow to a detactable size (growth time) and stochastic time needed for nucleation (true waiting time). The distribution of the true waiting time, is well explained by a stochastic model, in which nucleation is regarded to occur heterogeneously and in a stochastic manner by two kinds of active sites. The active sites are estimated to be located on foreign particles in which such elements as Si, Al and Mg were contained. The amount of each element is very small in the order of magnitude of ppb (mass basis) of the whole solution. The growth time was correlated with the degree of supercooling.

  15. Effect of aqueous extract of Ipomoea carnea leaf on isolated frog and mouse heart.

    Science.gov (United States)

    Bachhav, K V; Burande, M D; Rangari, V D; Mehta, J K

    1999-11-01

    Ipomoea carnea fam. Convolvulaceae is a poisonous plant and its toxicity is supposed to be due to the cardiac and respiratory failure. The present paper describes the cardiac effect of aqueous extract of the fresh leaves of I. carnea using mouse and frog heart. The aqueous extract produced an initial blockade of isolated frog heart for 5-10 sec followed by dose dependent increase in both amplitude and rate that lasts up to 2 min. Atropine (1 microgram/ml) blocked the initial depressant phase and potentiated the stimulant effect of the aqueous extract. The dose dependent increase in cardiac contractility of aqueous extract was not altered by propranolol or calcium channel blockers like nifedipine or diltiazem. The decrease in sodium chloride concentration or increase in potassium chloride concentration or calcium chloride concentration in physiological salt solution inhibited the responses to aqueous extract while an increase in sodium chloride concentration or decrease in potassium chloride or calcium chloride concentration in physiological salt solution potentiated the responses to the aqueous extract of I. carnea. It may be suggested from the data that aqueous extract of I. carnea produces positive inotropic effect on isolate frog heart possibly by sodium extrusion or release of the intracellular calcium.

  16. Functionalized polymers for binding to solutes in aqueous solutions

    Science.gov (United States)

    Smith, Barbara F.; Robison, Thomas W.

    2006-11-21

    A functionalized polymer for binding a dissolved molecule in an aqueous solution is presented. The polymer has a backbone polymer to which one or more functional groups are covalently linked. The backbone polymer can be such polymers as polyethylenimine, polyvinylamine, polyallylamine, and polypropylamine. These polymers are generally water-soluble, but can be insoluble when cross-linked. The functional group can be for example diol derivatives, polyol derivatives, thiol and dithiol derivatives, guest-host groups, affinity groups, beta-diphosphonic acids, and beta-diamides

  17. "Switchable water": aqueous solutions of switchable ionic strength.

    Science.gov (United States)

    Mercer, Sean M; Jessop, Philip G

    2010-04-26

    "Salting out" is a standard method for separating water-soluble organic compounds from water. In this method, adding a large amount of salt to the aqueous solution forces the organic compound out of the aqueous phase. However, the method can not be considered sustainable because it creates highly salty water. A greener alternative would be a method that allows reversible salting out. Herein, we describe aqueous solutions of switchable ionic strength. Aqueous solutions of a diamine in water have essentially zero ionic strength but are converted by CO(2) into solutions of high ionic strength. The change is reversible. Application to the reversible salting out of THF from water is described.

  18. Ion Exchange Extraction of Boron from Aqueous Fluids by Amberlite IRA 743 Resin

    Institute of Scientific and Technical Information of China (English)

    肖应凯; 廖步勇; 刘卫国; 肖云; SWIHART,GeorgeH.

    2003-01-01

    The ion exchange characteristics d Amherlite IRA 743 resin for extracting boron from aqueous fluids have been investigated in detail. The results show that AmherHte IRA 743 resin, a boron specific ion exchange resin, can quantitatively extract boron as the B (OH)4- spedes from weakly basle solution. Some exchangeable anions such as CI- and SO42- are present, resulting in an increase in pH value of the loeded solution within the nan, and the boron in natural aqueous fluids with low nH is also extracted by Amberlite IRA 743 resin. However, the voiume of loaded solution must be restricted. The maximum voiume of loaded solution giving quantitative extraction of boron decreases for sample soh.,tiom of lower pH value. Warm HCI solution is more effective than room temperature HCI solution for eluting boron from Amberllte IRA 743 resin.

  19. Hafnium extraction from acidic chloride solutions by Cyanex 923

    Energy Technology Data Exchange (ETDEWEB)

    El-Ammouri, E.; Distin, P.A. [McGill Univ., Montreal (Canada)

    1996-08-01

    Hafnium extraction from hydrochloric acid/lithium chloride solutions into Cyanex 923 in kerosene has been studied. Variables investigated were hydrochloric acid, total chloride and hafnium concentrations in the aqueous phase, and extractant/modifier (isodecanol) levels in the organic phase. Hafnium is considered to load as the tetrachloride complex forming a disolvate with Cyanex 923. Results are compared with equivalent data for zirconium extraction. 14 refs., 7 figs., 2 tabs.

  20. The extraction of uranium using graphene aerogel loading organic solution.

    Science.gov (United States)

    Chen, Mumei; Li, Zheng; Li, Jihao; Li, Jingye; Li, Qingnuan; Zhang, Lan

    2017-05-01

    A new approach for uranium extraction employing graphene aerogel (GA) as a skeleton loading organic solution (GA-LOS) is proposed and investigated. Firstly, the GA with super-hydrophobicity and high organic solution absorption capacity was fabricated by one-step reduction and self-assembly of graphene oxide with ethylenediamine. By adsorbing Tri-n-butyl phosphate (TBP)/n-dodecane solution to prepare GA-LOS, the extraction of U(VI) from nitric acid medium using GA-LOS was investigated and compared with conventional solvent extraction. It is found that the GA-LOS method can provide several advantages over conventional solvent extraction and adsorption due to the elimination of aqueous-organic mixing-separation procedures and easy solid-liquid separation. Furthermore, it also possesses higher extraction capacity (the saturated extraction capacity of GA loading TBP for U(VI) was 316.3mgg(-1) ) and lower consumption of organic diluents, leading to less organic waste. Moreover, the stability of GA-LOS in aqueous solution and cycling test were also studied, and it shows a remarkable regeneration capability, making it an ideal candidate for metal extraction from aqueous solution.

  1. Removal of Phenol from Dilute Solutions by Predispersed Solvent Extraction

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Predispersed solvent extraction (PDSE) is a new method for separating solutes from aqueous solution by solvent extraction and one which has shown promise for extraction from extremely dilute solution very efficient and very quick. The use of colloidal liquid aphrons in predispersed solvent extraction may ameliorate the problems such as emulsion formation, reduction of interfacial mass transfer and low interfacial mass transfer areas in solvent extraction process. In present paper, colloidal liquid aphrons are successfully generated using kerosene as a solvent, tributyl phosphate(TBP) as an extractant, sodium dodecyl benzene sulphate(SDBS) as surfactant in aqueous phase and Tween-80 in oil phase. Extraction of phenol from dilute solution was studied by using colloidal liquid aphrons and colloidal gas aphrons in a semi-batch extraction column. It has been found that the PDSE process is more suitable for extraction of dilute solutions. It has also been discovered that the PDSE process has a great advantage over traditional single-stage extraction process.

  2. Formation of hydroxyapatite in various aqueous solutions

    Science.gov (United States)

    Sturgeon, Jacqueline Lee

    Hydroxyapatite (HAp), Ca10(PO4)6(OH) 2, is important in the field of biomaterials as it is the mineral component of bones and teeth. Biological apatites do not maintain an exact composition and are usually calcium-deficient, represented as Ca(10- x)(HPO 4)x(PO4)(6-x)(OH)(2-x), where x ranges from 0 to 1, with various ion substitutions. Formation of calcium-deficient hydroxyapatites (CDHAp) from solid calcium phosphate precursor materials was performed at physiologic temperature (37°C) in a variety of aqueous solutions. Two cement systems were utilized in these experiments: tetralcium phosphate (TetCP) with dicalcium phosphate anhydrous (DCPA) and beta-tricalcium phosphate (beta-TCP). The kinetics, solution chemistry, phase evolution, and microstructure of the developed apatites were analyzed as appropriate. Reaction of beta-TCP in ammonium fluoride solutions formed HAp substituted with fluoride and calculated to be deficient in calcium. A new ratio of TetCP to DCPA was used with solutions of sodium bicarbonate to form a calcium-deficient carbonate hydroxyapatite. The capacity for sodium dihydrogen phosphate to buffer pH increases and enhance reaction kinetics in this system was also explored. Formation of a highly crystalline CDHAp was achieved by hydrolyzing beta-TCP in water for extended time periods. Lattice parameters were among the features characterized for this apatite. The hydrolysis of beta-TCP in phosphate buffered saline (PBS) and simulated body fluids (SBF) was also investigated; use of SBF was found to completely inhibit formation of HAp in this system while reaction in PBS was slow in comparison to water. The effects of filler materials on the mechanical properties of a calcium phosphate cement were examined using the TetCP/DCPA system. Dense aggregates were not found to decrease compressive strength in comparison to the cement alone. The use of aggregates was found to improve the compressive strength of cement formed using NaHCO3 solution as a

  3. The ultrasound-assisted aqueous extraction of rice bran oil.

    Science.gov (United States)

    Khoei, Maryam; Chekin, Fereshteh

    2016-03-01

    In this work, aqueous extraction of rice bran oil was done without and with ultrasound pretreatment. Key factors controlling the extraction and optimal operating conditions were identified. The highest extraction efficiency was found at pH=12, temperature of 45°C, agitation speed of 800rpm and agitation time of 15min, ultrasound treatment time of 70min and ultrasound treatment temperature of 25°C. Moreover, extraction yields were compared to ultrasound-assisted aqueous extraction and Soxhlet extraction. The results showed that the yield of rice bran oil at ultrasound-assisted aqueous extraction was close to the yield of oil extracted by hexane Soxhlet extraction. This result implied that the yield of rice bran oil was significantly influenced by ultrasound. With regard to quality, the oil extracted by ultrasound-assisted aqueous process had a lower content of free fatty acid and lower color imparting components than the hexane-extracted oil. Also, effect of parboiling of paddy on hexane and ultrasound-assisted aqueous extraction was studied. Both extraction methods gives higher percentage of oil from par boiled rice bran compared with raw rice bran. This may be due to the fact that parboiling releases the oil.

  4. Ionic liquid-modified silica-coated magnetic nanoparticles: promising adsorbents for ultra-fast extraction of paraquat from aqueous solution.

    Science.gov (United States)

    Latifeh, Farzad; Yamini, Yadollah; Seidi, Shahram

    2016-03-01

    In the present study, ionic liquid-modified silica-coated magnetic nanoparticles (Fe3O4@SiO2@IL) were synthesized and applied as adsorbents for extraction and determination of paraquat (PQ) followed by high-performance liquid chromatography. For assurance of the extraction efficiency, the obtained results were compared with those obtained by bared magnetic nanoparticles (MNPs). Experimental design and response surface methodology were used for optimization of different parameters which affect extraction efficiency of paraquat using both adsorbents. Under the optimized conditions, extraction recoveries in the range of 20-25 and 35-40 % with satisfactory repeatability values (RSDs%, n = 4) less than 5.0 % were obtained for bared MNPs and Fe3O4@SiO2@IL, respectively. The limits of detection were 0.1 and 0.25 μg/L using Fe3O4@SiO2@IL and bared MNPs, respectively. The linearity was obtained in the range of 0.25 to 25 μg/L and 0.5 to 25 μg/L for Fe3O4@SiO2@IL and bared MNPs, respectively, with the coefficients of determination better than 0.9950. Finally, Fe3O4@SiO2@IL was chosen as superior adsorbent due to more dispersion ability, higher extraction recovery, lower detection limit, as well as better linearity and repeatability. Calculated errors (%) were in the range of 3 to 10 % depicting acceptable accuracy for the analysis of PQ by the proposed method. Finally, the method was successfully applied for extraction and determination of PQ in some water and countryside soil samples.

  5. 21 CFR 524.1200b - Kanamycin ophthalmic aqueous solution.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Kanamycin ophthalmic aqueous solution. 524.1200b Section 524.1200b Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... § 524.1200b Kanamycin ophthalmic aqueous solution. (a) Specifications. The drug, which is in an...

  6. Structure of aqueous sodium perchlorate solutions.

    Science.gov (United States)

    General, Ignacio J; Asciutto, Eliana K; Madura, Jeffry D

    2008-12-01

    Salt solutions have been the object of study of many scientists through history, but one of the most important findings came along when the Hofmeister series were discovered. Their importance arises from the fact that they influence the relative solubility of proteins, and solubility is directly related to one of today's holy grails: protein folding. In this work we characterize one of the more-destabilizing salts in the series, sodium perchlorate, by studying it as an aqueous solution at various concentrations ranging from 0.08 to 1.60 mol/L. Molecular dynamics simulations at room temperature permitted a detailed study of the organization of solvent and cosolvent, in terms of its radial distribution functions, along with the study of the structure of hydrogen bonds in the ions' solvation shells. We found that the distribution functions have some variations in their shape as concentration changes, but the position of their peaks is mostly unaffected. Regarding water, the most salient fact is the noticeable (although small) change in the second hydration shell and even beyond, especially for g(O(w)***O(w)), showing that the locality of salt effects should not be restricted to considerations of only the first solvation shell. The perturbation of the second shell also appears in the study of the HB network, where the difference between the number of HBs around a water molecule and around the Na(+) cation gets much smaller as one goes from the first to the second solvation shell, yet the difference is not negligible. Nevertheless, the effect of the ions past their first hydration shell is not enough to make a noticeable change in the global HB network. The Kirkwood-Buff theory of liquids was applied to our system, in order to calculate the activity derivative of the cosolvent. This coefficient, along with a previously calculated preferential binding, allowed us to establish that if a folded AP peptide is immersed in the studied solution, becoming the solute, then

  7. Fluoride Adsorption by Pumice from Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Amir Hossein Mahvi

    2012-01-01

    Full Text Available Drinking water provides many vital elements for the human body, but the presence of some dissolved elements more than permissible concentration can endanger human health. Among the dissolved elements in drinking water, fluoride is noticeable, because both the very low or very high concentrations have adverse health impacts such as dental caries. Therefore, fluoride concentration should be kept in acceptable levels. In this study Pumice was used for fluoride removal. It was found that Fluoride sorption kinetic was fitted by pseudo-second-order model. The maximum sorption capacity of Pumice was found to be 13.51 mg/g at laboratory temperature (24°C. Maximum sorption study occurred at pH= 3. Results of Isotherm showed the fluoride sorption has been well fitted with Freundlich isotherm model. This study has demonstrated that Pumice can be used as effective adsorbents for fluoride removal from aqueous solutions. The adsorbent prepared in this study was cheap and efficient in removal of fluoride than other adsorbents.

  8. A method for separating water soluble organics from a process stream by aqueous biphasic extraction

    Energy Technology Data Exchange (ETDEWEB)

    Chaiko, David J.; Mego, William A.

    1997-12-01

    The present invention relates to a method for separating water-miscible organic species from a process stream by aqueous biphasic extraction. In particular, the method includes extracting the organic species into a polymer-rich phase of an aqueous biphase system in which the process stream comprises the salt-rich phase, and, next, separating the polymer from the extracted organic species by contacting the loaded, polymer-rich phase with a water-immiscible organic phase. Alternatively, the polymer can be separated from the extracted organic species by raising the temperature of the loaded, polymer-rich phase above the cloud point, such that the polymer and the water-soluble organic species separate into two distinct aqueous phases. In either case, a substantially salt-free, concentrated aqueous solution containing the organic species is recovered.

  9. Tunable aqueous polymer-phase impregnated resins-technology-a novel approach to aqueous two-phase extraction.

    Science.gov (United States)

    van Winssen, F A; Merz, J; Schembecker, G

    2014-02-14

    Aqueous Two-Phase Extraction (ATPE) represents a promising unit operation for downstream processing of biotechnological products. The technique provides several advantages such as a biocompatible environment for the extraction of sensitive and biologically active compounds. However, the tendency of some aqueous two-phase systems to form intensive and stable emulsions can lead to long phase separation times causing an increased footprint for the required mixer-settler devices or the need for additional equipment such as centrifuges. In this work, a novel approach to improve ATPE for downstream processing applications called 'Tunable Aqueous Polymer-Phase Impregnated Resins' (TAPPIR(®))-Technology is presented. The technology is based on the immobilization of one aqueous phase inside the pores of a solid support. The second aqueous phase forms the bulk liquid around the impregnated solids. Due to the immobilization of one phase, phase emulsification and phase separation of ATPE are realized in a single step. In this study, a biodegradable and sustainable aqueous two-phase system consisting of aqueous polyethylene glycol/sodiumcitrate solutions was chosen. The impregnation of different macroporous glass and ceramic solids was investigated and could be proven to be stable. Additionally, the separation of the dye Patent blue V was successfully performed with the TAPPIR(®)-Technology. Thus, the "proof of principle" of this technology is presented.

  10. Solid phase extraction of chromium(VI) from aqueous solutions by adsorption of its diphenylcarbazide complex on an Amberlite XAD-4 resin column.

    Science.gov (United States)

    Rajesh, N; Jalan, Rohit Kumar; Hotwany, Pinky

    2008-02-11

    A method has been developed for the solid phase extraction of chromium(VI) based on the adsorption of its diphenylcarbazide complex on an Amberlite XAD-4 resin column. The influence of acidity, stability of the column, sample volume, flow rate and interfering ions were studied in detail. The adsorbed complex could be eluted using acetone-sulfuric acid mixture and the concentration of chromium was determined using visible spectrophotometry. A detection limit of 6 microg L(-1) could be achieved. A preconcentration factor of 27 could be obtained for 400 mL sample volume. The validity of the method was checked in spiked water samples and electroplating wastewater.

  11. Ozone photolysis of paracetamol in aqueous solution.

    Science.gov (United States)

    Neamţu, Mariana; Bobu, Maria; Kettrup, Antonius; Siminiceanu, Ilie

    2013-01-01

    The degradation of a paracetamol (N-acetil-para-aminofenol) aqueous solution (C (0) P = 5 mmol L(-1)) is studied in a bench-scale setup by means of simple ozonation (O3) and ozonation catalyzed with UV light (O3/UV) in order to quantify the influence of UV light on the degradation process. The results have shown that under the adopted experimental conditions (25°C, applied ozone dose = 9.8 mg L(-1) and gas flow rate of 20 L h(-1)) both oxidative systems are capable of removing the substrate with mineralization degrees up to 51% for ozonation and 53% for O3/UV. HPICE chromatography allowed the detection of nitrate ions and maleic and oxalic acids as ultimate carboxylic acids. The experimental data have been interpreted through 5 indicators: the conversion of paracetamol (XP ), the conversion degree of TOC (XTOC ), the apparent rate constant (kap ), the Hatta number (Ha) and the enhancement factor (E). The main advantage of photo-ozonation compared to simple ozonation was a more advanced conversion (79% vs. 92% after 90 min). The paracetamol decay follows a pseudo-first-order reaction with a superior rate constant (higher by 54%) for the UV catalyzed system in comparison with direct ozonation. Mineralization is slightly accelerated (+4%) in the O3/UV system, due to the additional production of hydroxyl radicals induced by the UV light and a higher Hatta number (+24%). Nevertheless, the process was still in the slow reaction kinetic regime (Ha < 0.3), and the enhancement factor was not significantly increased. The results are useful for the design and scale-up of the gas-liquid processes.

  12. Photolysis of Periodate and Periodic Acid in Aqueous Solution

    DEFF Research Database (Denmark)

    Sehested, Knud; Kläning, U. K.

    1978-01-01

    The photochemistry of periodate and periodic acid in aqueous solution was studied (i) by quantum yield measurements at low light intensity (ii) by flash photolysis, and (iii) by photolysis of glassy samples at 77 K. The photochemical studies were supplemented with pulse radiolysis studies...... of aqueous periodate solutions and with kinetic studies using stopped-flow technique. In strongly alkaline solution the photodecomposition of periodate proceeds via formation of O– and IVI. At pH

  13. Thermophysical Properties of Aqueous Solutions Used as Secondary Working Fluids

    OpenAIRE

    Melinder, Åke

    2007-01-01

    Secondary working fluids (secondary refrigerants, heat transfer fluids, antifreezes, brines) have long been used in various indirect re-frigeration and heat pump systems. Aqueous solutions (water solu-tions) have long been used as single phase (liquid only) secondary working fluids for cooling in supermarkets, ice rinks, heat recovery systems, heat pumps and other applications. However, aqueous solutions are increasingly used also for freezers in supermarkets and other applications in low tem...

  14. Efficient indium-tin-oxide free inverted organic solar cells based on aluminum-doped zinc oxide cathode and low-temperature aqueous solution processed zinc oxide electron extraction layer

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Dazheng; Zhang, Chunfu, E-mail: cfzhang@xidian.edu.cn; Wang, Zhizhe; Zhang, Jincheng; Tang, Shi; Wei, Wei; Sun, Li; Hao, Yue, E-mail: yhao@xidian.edu.cn [State Key Discipline Laboratory of Wide Band Gap Semiconductor Technology, School of Microelectronics, Xidian University, No. 2 South Taibai Road, Xi' an 710071 (China)

    2014-06-16

    Indium-tin-oxide (ITO) free inverted organic solar cells (IOSCs) based on aluminum-doped zinc oxide (AZO) cathode, low-temperature aqueous solution processed zinc oxide (ZnO) electron extraction layer, and poly(3-hexylthiophene-2, 5-diyl):[6, 6]-phenyl C{sub 61} butyric acid methyl ester blend were realized in this work. The resulted IOSC with ZnO annealed at 150 °C shows the superior power conversion efficiency (PCE) of 3.01%, if decreasing the ZnO annealing temperature to 100 °C, the obtained IOSC also shows a PCE of 2.76%, and no light soaking issue is observed. It is found that this ZnO film not only acts as an effective buffer layer but also slightly improves the optical transmittance of AZO substrates. Further, despite the relatively inferior air-stability, these un-encapsulated AZO/ZnO IOSCs show comparable PCEs to the referenced ITO/ZnO IOSCs, which demonstrates that the AZO cathode is a potential alternative to ITO in IOSCs. Meanwhile, this simple ZnO process is compatible with large area deposition and plastic substrates, and is promising to be widely used in IOSCs and other relative fields.

  15. Critical properties of aqueous solutions. Part 1: Experimental data

    Science.gov (United States)

    Abdulagatov, A. I.; Stepanov, G. V.; Abdulagatov, I. M.

    2008-08-01

    All data available in the literature on the critical properties of binary aqueous solutions like H2O + common salt, H2O + hydrocarbon, H2O + alcohol, H2O + gas, and others are gathered. Methods for determining them are presented together with errors and concentration measurement intervals for each source of data. The format in which the data are presented will allow the readers to quickly find the necessary information on the critical properties of aqueous solutions from the original sources and use them for solving scientific and engineering tasks. Certain general features of the critical lines and phase diagrams of aqueous solutions with volatile and nonvolatile components are discussed.

  16. Extraction of Fe(III) and U(VI) with 1-phenyl-3-methyl-4-acyl-pyrazolones-5 from aqueous solutions of different acids and complexing agents. Separation of Fe(III) from U(VI)

    Energy Technology Data Exchange (ETDEWEB)

    Okafor, E.C. (Nigeria Univ., Nsukka (Nigeria). Dept. of Pure and Industrial Chemistry); Uzoukwu, B.A. (Port Harcourt Univ. (Nigeria). Dept. of Pure and Industrial Chemistry)

    1990-01-01

    Solvent extraction behaviour of Fe(III) and U(VI) in aqueous media containing various mineral acids or complexing agents, using 4-butyryl, 4-palmitoyl and 4-trichloroacetyl derivatives of 1-phenyl-3-methyl-pyrazolone-5 in xylene as extraction reagents have been studied. The possible extraction mechanism has been investigated. Solid complexes of Fe(III) and U(VI) with the chelating agents have been isolated and analysed. Separation factors of Fe(III) and U(VI) using these chelating agents are reported and methods suggested for separation of Fe(III) from U(VI) in an aqueous medium containing 0.1 M HCl or 5x10{sup -4} M EDTA. (orig.).

  17. Extractive removal of chromium (VI) from industrial waste solution.

    Science.gov (United States)

    Agrawal, Archana; Pal, Chandana; Sahu, K K

    2008-11-30

    Extractive removal of Cr (VI) was carried out from chloride solutions using cyanex 923 mixed with kerosene. The efficiency of this extractant was studied under various experimental conditions, such as concentration of different mineral acids in the aqueous phase, concentration of cyanex 923 and Cr (VI) present in the initial aqueous feed, temperature and time of extraction, organic to aqueous (O/A) phase ratio. Percentage Cr (VI) extraction decreases with the increase in temperature at varying concentration of cyanex 923. The interference of the impurities usually associated with Cr (VI) such as Cr (III), Cu, Ni, Fe (II), Zn, Chloride and sulphate, etc., were examined under the optimized conditions and only Zn was found to interfere. Under the optimum experimental conditions 98.6-99.9% of Cr (VI) was extracted in 3-5 min at O/A of 2 with the initial feed concentration of 1g/L of Cr (VI). The extracted Cr (VI) was quantitatively stripped with 1M NaOH and the organic phase obtained after the stripping of Cr (VI) was washed with dilute HCl solution to neutralize any NaOH trapped/adhered to the solvent and then with distilled water. This regenerated solvent was reused in succeeding extraction of chromium (VI). Finally a few experiments were performed with the synthetic effluent from an electroplating industry.

  18. Instability of aqueous solutions of polyacrylamide in a hydrodynamic field

    Science.gov (United States)

    Makogon, B. P.; Bykova, E. N.; Bezrukova, M. A.; Klenin, S. I.; Ivanyuta, Yu. F.; Povkh, I. L.; Toryanik, A. I.

    1985-09-01

    This article discusses findings obtained regarding the effect of a hydrodynamic field on the reduced viscosity, effect of turbulent friction reduction, light scattering, double refraction, and optical density of aqueous solutions of hydrolyzed polyacrylamide.

  19. Hypoglycemic Activity of Aqueous Extracts from Catharanthus roseus

    Directory of Open Access Journals (Sweden)

    Elisa Vega-Ávila

    2012-01-01

    Full Text Available Introduction. Catharanthus roseus (L. is used in some countries to treat diabetes. The aim of this study was to evaluate the hypoglycemic activity of extracts from the flower, leaf, stem, and root in normal and alloxan-induced diabetic mice. Methods. Roots, leaves, flowers, and stems were separated to obtain organic and aqueous extracts. The blood glucose lowering activity of these extracts was determinate in healthy and alloxan-induced (75 mg/Kg diabetic mice, after intraperitoneal administration (250 mg/Kg body weight. Blood samples were obtained and blood glucose levels were analyzed employing a glucometer. The data were statistically compared by ANOVA. The most active extract was fractioned. Phytochemical screen and chromatographic studies were also done. Results. The aqueous extracts from C. roseus reduced the blood glucose of both healthy and diabetic mice. The aqueous stem extract (250 mg/Kg and its alkaloid-free fraction (300 mg/Kg significantly ( reduced blood glucose in diabetic mice by 52.90 and 51.21%. Their hypoglycemic activity was comparable to tolbutamide (58.1%, . Conclusions. The best hypoglycemic activity was presented for the aqueous extracts and by alkaloid-free stem aqueous fraction. This fraction is formed by three polyphenols compounds.

  20. Hypoglycemic Activity of Aqueous Extracts from Catharanthus roseus

    Science.gov (United States)

    Vega-Ávila, Elisa; Cano-Velasco, José Luis; Alarcón-Aguilar, Francisco J.; Fajardo Ortíz, María del Carmen; Almanza-Pérez, Julio César; Román-Ramos, Rubén

    2012-01-01

    Introduction. Catharanthus roseus (L.) is used in some countries to treat diabetes. The aim of this study was to evaluate the hypoglycemic activity of extracts from the flower, leaf, stem, and root in normal and alloxan-induced diabetic mice. Methods. Roots, leaves, flowers, and stems were separated to obtain organic and aqueous extracts. The blood glucose lowering activity of these extracts was determinate in healthy and alloxan-induced (75 mg/Kg) diabetic mice, after intraperitoneal administration (250 mg/Kg body weight). Blood samples were obtained and blood glucose levels were analyzed employing a glucometer. The data were statistically compared by ANOVA. The most active extract was fractioned. Phytochemical screen and chromatographic studies were also done. Results. The aqueous extracts from C. roseus reduced the blood glucose of both healthy and diabetic mice. The aqueous stem extract (250 mg/Kg) and its alkaloid-free fraction (300 mg/Kg) significantly (P < 0.05) reduced blood glucose in diabetic mice by 52.90 and 51.21%. Their hypoglycemic activity was comparable to tolbutamide (58.1%, P < 0.05). Conclusions. The best hypoglycemic activity was presented for the aqueous extracts and by alkaloid-free stem aqueous fraction. This fraction is formed by three polyphenols compounds. PMID:23056144

  1. Gold and Silver Extraction from Leach Solutions

    OpenAIRE

    Bagdaulet K. Kenzhaliyev; Renata R. Iskhakova; Zamzagul D. Dosymbaeva; Esen N. Sulejmenov

    2014-01-01

    There has been carried out an investigation on the extraction of gold and silver from thiosulfate solutions: standard test and technological solutions of chemical and electrochemical leaching. The influence of related metals on the process of extracting gold from solution was studied. There has been conducted a comparative study of the IR spectra of solutions after the sorption of gold, silver and related metals.

  2. Surface tension and related thermodynamic quantities of aqueous electrolyte solutions

    CERN Document Server

    Matubayasi, Norihiro

    2013-01-01

    Surface tension provides a thermodynamic avenue for analyzing systems in equilibrium and formulating phenomenological explanations for the behavior of constituent molecules in the surface region. While there are extensive experimental observations and established ideas regarding desorption of ions from the surfaces of aqueous salt solutions, a more successful discussion of the theory has recently emerged, which allows the quantitative calculation of the distribution of ions in the surface region. Surface Tension and Related Thermodynamic Quantities of Aqueous Electrolyte Solutions provides a d

  3. Biosorption of arsenic from aqueous solution using dye waste.

    Science.gov (United States)

    Nigam, Shubha; Vankar, Padma S; Gopal, Krishna

    2013-02-01

    The purpose of this study is to examine on removal of arsenic from water by biosorption through potential application of herbal dye wastes. Four different flower dye residues (after extraction of natural dye) viz. Hibiscus rosasinensis, Rosa rosa, Tagetes erecta, and Canna indica were utilized successfully for the removal of arsenic from aqueous solution. Batch studies were carried out for various parameters viz. pH, sorbent dose, contact time, initial metal ion concentration, and temperature. Data were utilized for isothermal, kinetic, and thermodynamic studies. Scanning electron microscopy (SEM), energy-dispersive x-ray spectroscopy (EDAX), and Fourier transform infrared (FTIR) analyses of biomass were performed. The results showed that 1 g/100 ml for 5.0-5.5 h contact time at pH 6.0-7.5 with agitation rate 150 rpm provided 98, 96, 92, and 85 % maximum absorption of arsenic by R. rosa, H. rosasinensis, T. erecta, and C. indica, respectively, at initial concentration of 500 ppb. Data followed Langmuir isotherm showing sorption to be monolayer on heterogeneous surface of biosorbent. Negative values of ΔG° indicated spontaneous nature, whereas ΔH° indicates exothermic nature of system followed by pseudo-first-order adsorption kinetics. FTIR results showed apparent changes in functional group regions after metal chelation. SEM and EDAX analyses showed the changes in surface morphology of all test biosorbents. Herbal dye wastes, used as biosorbent, exhibited significant (85-98 %) removal of arsenic from aqueous solution. Hence, these biosorbents are cost-effective, easily available, eco-friendly, and comparatively more effective than other biosorbents already in use. These may be used to remove arsenic and other toxic metals from water.

  4. Method for separating water soluble organics from a process stream by aqueous biphasic extraction

    Energy Technology Data Exchange (ETDEWEB)

    Chaiko, D.J.; Mego, W.A.

    1999-09-07

    A method for separating water-miscible organic species from a process stream by aqueous biphasic extraction is provided. An aqueous biphase system is generated by contacting a process stream comprised of water, salt, and organic species with an aqueous polymer solution. The organic species transfer from the salt-rich phase to the polymer-rich phase, and the phases are separated. Next, the polymer is recovered from the loaded polymer phase by selectively extracting the polymer into an organic phase at an elevated temperature, while the organic species remain in a substantially salt-free aqueous solution. Alternatively, the polymer is recovered from the loaded polymer by a temperature induced phase separation (cloud point extraction), whereby the polymer and the organic species separate into two distinct solutions. The method for separating water-miscible organic species is applicable to the treatment of industrial wastewater streams, including the extraction and recovery of complexed metal ions from salt solutions, organic contaminants from mineral processing streams, and colorants from spent dye baths.

  5. Method for separating water soluble organics from a process stream by aqueous biphasic extraction

    Energy Technology Data Exchange (ETDEWEB)

    Chaiko, David J. (Naperville, IL); Mego, William A. (Naperville, IL)

    1999-01-01

    A method for separating water-miscible organic species from a process stream by aqueous biphasic extraction is provided. An aqueous biphase system is generated by contacting a process stream comprised of water, salt, and organic species with an aqueous polymer solution. The organic species transfer from the salt-rich phase to the polymer-rich phase, and the phases are separated. Next, the polymer is recovered from the loaded polymer phase by selectively extracting the polymer into an organic phase at an elevated temperature, while the organic species remain in a substantially salt-free aqueous solution. Alternatively, the polymer is recovered from the loaded polymer by a temperature induced phase separation (cloud point extraction), whereby the polymer and the organic species separate into two distinct solutions. The method for separating water-miscible organic species is applicable to the treatment of industrial wastewater streams, including the extraction and recovery of complexed metal ions from salt solutions, organic contaminants from mineral processing streams, and colorants from spent dye baths.

  6. The effect of aqueous solution in Raman spectroscopy

    Science.gov (United States)

    Kang, Jian; Yuan, Xiaojuan; Dong, Xiao; Gu, Huaimin

    2009-08-01

    In Raman detection, the most popular solution for the samples is tri-distilled water. But the effect of aqueous solution is barely studied in Raman spectroscopy. In fact Raman spectroscopy of solid-state and liquid-state are obvious different. In addition, FWHM of Raman spectral peaks also change evidently. In this paper, several samples were selected for the experiment; including sodium nitrate, sodium nitrite, glucose and caffeine. By comparing the Raman spectroscopy of samples at different concentrations, it is found that the concentration of the sample can affect the strength of Raman spectroscopy, but it can hardly impact FWHM of Raman spectral peaks. By comparing the Raman spectroscopy of liquid-state with the Raman spectroscopy of solid-state, it is observed that the FWHM of some Raman spectral peaks varied obviously; that may be because when the sample was dissolved into the water, the crystal lattice structure was broken, and for some samples atom form became ion form in aqueous solution. Those structural variations caused the variation of the FWHM. The Raman spectroscopy of caffeine aqueous solution at very low concentration was also detected and analyzed. Compared with the Raman spectra of solid-state samples, it is found that some Raman spectral peaks disappeared when the sample was dissolved in water. It is possible that the low concentration of the sample result in the weakening of Raman signals and the disappearing of some weak Raman spectral peaks. Then Ag nanoparticles were added into the caffeine aqueous solution, the results suggest that surface enhanced Raman spectroscopy (SERS) not only can enhance the Raman spectral signal, but also can reduce the effect of aqueous solution. It is concluded that the concentration of sample only affects the strength of Raman spectroscopy; the aqueous solution can affect the FWHM of Raman spectral peaks; and SERS can reduce the effect of aqueous solution.

  7. Extraction and separation of tungsten (VI) from aqueous media with Triton X-100-ammonium sulfate-water aqueous two-phase system without any extractant.

    Science.gov (United States)

    Yongqiang Zhang; Tichang Sun; Tieqiang Lu; Chunhuan Yan

    2016-11-25

    An aqueous two-phase system composed of Triton X-100-(NH4)2SO4-H2O was proposed for extraction and separation of tungsten(VI) from aqueous solution without using any extractant. The effects of aqueous pH, concentration of ammonium sulfate, Triton X-100 and tungsten, extracting temperature on the extraction of tungsten were investigated. The extraction of tungsten has remarkable relationship with aqueous pH and are to above 90% at pH=1.0-3.0 under studied pH range (pH=1.0-7.0) and increases gradually with increasing Triton X-100 concentration, but decreases slightly with increasing ammonium sulfate concentration. The extraction percentage of tungsten is hardly relevant to temperature but its distribution coefficient linearly increases with increasing temperature within 303.15-343.15K. The distribution coefficient of tungsten increases with the increase of initial tungsten concentration (0.1-3%) and temperature (303.15 K-333.15K). The solubilization capacity of tungsten in Triton X-100 micellar phase is independent of temperature. FT-IR analysis reveals that there is no evident interaction between polytungstate anion and ether oxygen unit in Triton X-100, and DLS analysis indicates that zeta potential of Triton X-100 micellar phase have a little change from positive to negative after extracting tungsten. Based on the above-mentioned results, it can be deduced that polytungstate anions are solubilized in hydrophilic outer shell of Triton X-100 micelles by electrostatic attraction depending on its relatively high hydrophobic nature. The stripping of tungsten is mainly influenced by temperature and can be easily achieved to 95% in single stage stripping. The tungsten (VI) is separated out from solution containing Fe(III), Co(II), Ni(II), Cu(II), Zn(II), Al(III), Cr(III) and Mn(II) under the suitable conditions.

  8. Analgesic effect of the aqueous and ethanolic extracts of clove

    Directory of Open Access Journals (Sweden)

    Mina Kamkar Asl

    2013-04-01

    Full Text Available Objective: The beneficial effects of clove on toothache have been well documented. We have also previously shown the analgesic effects of clove essential oil. The present work was done to investigate the analgesic effects of the aqueous extract of clove using hot plate test. The possible role of opioid receptors in the analgesic effects of clove was also investigated using naloxone. Materials and Methods: Ninety male mice were divided into nine groups: (1 Saline, (2-4 Aaqueous (Aq 50, Aq 100, and Aq 200 groups which were treated with 50, 100, and 200 mg/kg of aqueous extract of clove, respectively, (5-7 Ethanolic (Eth 50, Eth 100, and Eth 200 groups which were treated with 50, 100, and 200 mg/kg of ethanolic extract of clove, respectively, and (8-9 Aq 100- Naloxone and Aq 200- Naloxone which were pretreated with 4 mg/kg of naloxone before injection of 100 or 200 mg/kg of the aqueous extract. The hot plate test was performed as a base record 10 min before injection of drugs and consequently repeated every 10 minutes after the injection. Results: The maximal percent effect (MPE in the animal groups treated with 50, 100, and 200 mg/kg of aqueous extract was significantly higher than the control group. Pretreatment with naloxone reduced the analgesic effects of both 100 and 200 mg/kg of the aqueous extract. Administration of all three doses of the ethanloic extract also non-significantly increased the MPE. Conclusion: The results of the present study showed that aqueous extract of clove has analgesic effect in mice demonstrated by hot plate test which is reversible by naloxone. The role of opioid system in the analgesic effect of clove might be suggested. However, more investigations are needed to elucidate the exact mechanism(s.

  9. Eco-friendly synthesis of Graphene using the aqueous extract of Amaranthus dubius

    Directory of Open Access Journals (Sweden)

    M. Jannathul Firdhouse

    2013-06-01

    Full Text Available An eco-friendly process of reduction of graphene oxide using aqueous extract of Amaranthus dubius under refluxing method is herein reported. The colour change of the graphene oxide (GO solution from brown to black was noted during the reduction of graphene oxide. UV-Visible spectrophotometer was used to monitor the formation of reduced graphene oxide (AKRGO. The crystallite size of nanographene was confirmed by XRD analysis and Scherrer’s formula. FTIR spectral analysis revealed the reduction of graphene oxide using aqueous extract of Amaranthus dubius. The morphology of the synthesized graphene was examined by SEM analysis.

  10. Label-free monitoring of interaction between DNA and oxaliplatin in aqueous solution by terahertz spectroscopy

    Science.gov (United States)

    Wu, Xiaojun; E, Yiwen; Xu, Xinlong; Wang, Li

    2012-07-01

    We demonstrated the feasibility of applying terahertz time-domain spectroscopy (THz-TDS) to monitor the molecular reactions in aqueous solutions of anticancer drug oxaliplatin with λ-DNA and macrophages DNA. The reaction time dependent refractive index and absorption coefficient were extracted and analyzed. The reaction half-decaying time of about 4.0 h for λ-DNA and 12.9 h for M-DNA was established. The results suggest that the THz-TDS detection could be an effective label-free technique to sense the molecular reaction in aqueous solutions and could be very useful in biology, medicine, and pharmacy industry.

  11. Aqueous solutions at the interface with phospholipid bilayers.

    Science.gov (United States)

    Berkowitz, Max L; Vácha, Robert

    2012-01-17

    In a sense, life is defined by membranes, because they delineate the barrier between the living cell and its surroundings. Membranes are also essential for regulating the machinery of life throughout many interfaces within the cell's interior. A large number of experimental, computational, and theoretical studies have demonstrated how the properties of water and ionic aqueous solutions change due to the vicinity of membranes and, in turn, how the properties of membranes depend on the presence of aqueous solutions. Consequently, understanding the character of aqueous solutions at their interface with biological membranes is critical to research progress on many fronts. The importance of incorporating a molecular-level description of water into the study of biomembrane surfaces was demonstrated by an examination of the interaction between phospholipid bilayers that can serve as model biological membranes. The results showed that, in addition to well-known forces, such as van der Waals and screened Coulomb, one has to consider a repulsion force due to the removal of water between surfaces. It was also known that physicochemical properties of biological membranes are strongly influenced by the specific character of the ions in the surrounding aqueous solutions because of the observation that different anions produce different effects on muscle twitch tension. In this Account, we describe the interaction of pure water, and also of aqueous ionic solutions, with model membranes. We show that a symbiosis of experimental and computational work over the past few years has resulted in substantial progress in the field. We now better understand the origin of the hydration force, the structural properties of water at the interface with phospholipid bilayers, and the influence of phospholipid headgroups on the dynamics of water. We also improved our knowledge of the ion-specific effect, which is observed at the interface of the phospholipid bilayer and aqueous solution, and its

  12. Acidities of Water and Methanol in Aqueous Solution and DMSO

    Science.gov (United States)

    Gao, Daqing

    2009-01-01

    The relative acidities of water and methanol have been a nagging issue. In gas phase, methanol is more acidic than water by 36.0 kJ/mol; however, in aqueous solution, the acidities of methanol and water are almost identical. The acidity of an acid in solution is determined by both the intrinsic gas-phase ionization Gibbs energy and the solvent…

  13. Synthesis and Aqueous Solution Viscosity of Hydrophobically Modified Xanthan Gum

    Institute of Scientific and Technical Information of China (English)

    QIAN Xiao-lin; WU Wen-hui; YU Pei-zhi; WANG Jian-quan

    2007-01-01

    Two xanthan gum derivatives hydrophobically modified by 4 or 8 tetradecyl chains per 100 xanthan gum structure units were synthesized. The derivatives were studied by scanning electron microscope and pyrene fluorescence spectrometry. And the aqueous solution apparent viscosity of the derivatives was investigated. The results indicate that the network of the derivatives with more hydrophobic groups is closer and tighter. With increasing of alkyl chain substitution degree, the hydrophobically associating interactions enhance in aqueous solution. Aqueous solution apparent viscosity of the derivatives increases with increasing of polymer concentration and alkyl substitution degree, and decreases with the increase of temperature. In the brine solution, the strong viscosity enhancement phenomenon appears. The interaction between the derivatives and surfactant sodium dodecylbenzene sulfonate is strong.

  14. STUDIES ON METHOD FOR AQUEOUS EXTRACTION OF SOYBEAN OIL

    Institute of Scientific and Technical Information of China (English)

    钱俊青

    2001-01-01

    Water extraction of soybean oil was studied to find the optimal conditions for recovery of oil pre-enriched protein and for aqueous extraction of soybean oil. Orthogonal tests were employed in the procedures of oil pre-enrichment and aqueous extraction. Soybeans were crushed to pass a 40 mesh sieve, soaked under the optimum conditions (solid/water=1/5(w/v), 40 ℃, pH 10, 3 h) and water-ground to 100 mesh, stirred in 65 ℃ water for 20 min, and centrifuged at 1400 g to separate oil pre-enriched protein. The protein yield was 17.8 g from 100 g soybeans, which contained 62.8% oil. The oil yield was 69.0%. Optimum conditions for the aqueous extraction procedure were: solid-to-water ratio 1∶2, pH 9.0, time 30 min, stirring in boiling water bath, stationary time 10 min, centrifuge at 3600 g for 10 min. Experimental values showed that the oil yield after aqueous extraction from oil pre-enriched protein reached 88.3%, so the total oil extraction rate was 60.8%.

  15. Deacidification of oils and fats of biological origine by aqueous solutions of tertiary amines*

    Directory of Open Access Journals (Sweden)

    Peter Siegfried

    2001-01-01

    Full Text Available Deacidification of triacylglycerols by extraction is investigated using aqueous solutions of amines as extractants. Tertiary amines with boiling points ranging between 100° and 170°C, such as 2-methylamino-diethanol, 2-dimethylamino-ethanol, 4-methylmorpholine, 1-dimethylamino-2-propanol etc. were found to be suitable substances. Especially the deacidification by aqueous solutions of 2-dimethylamino-ethanol (DMAE was amply investigated as it is used as an active agent in remedies. Amazingly gelatinous soap stocks are not formed, when the concentration of DMAE exceeds 20% if the free fatty acid content of the oil is below 15%. Two liquid phases are formed in systems composed of triacylglyceroles and aqueous solutions containing 20 to 80% DMAE. Palm oil containing 4.3 wt.% free fatty acids was mixed with an equal amount of an aqueous solution of 30 wt.% DMAE at 60°C. In equilibrium an extract containing 86 wt.% free fatty acids (solvents deducted and a raffinate of 0.09 wt.% free fatty acids are obtained. Loss of neutral oil being 0.7 wt.%.

  16. Extraction of Palladium (Ⅱ) with p-Methylphenylalkylsulfide from Aqueous Chloride Media

    Institute of Scientific and Technical Information of China (English)

    杨立; 章正熙; 刘旭辉; 郭亚莉; 二井晋; 竹内宽

    2005-01-01

    p-Methylphenylalkylsulfide of various alkyl chain length as extractant were synthesized and the extraction of palladium was examined in terms of equilibrium and kinetics. Distribution ratio of Pd was independent of alkyl chain length. For aqueous chloride media, there was a significant difference in distribution ratios for the solution of NaC1 and HC1. The results of loading test and the slope analysis suggest that the extractant and Pd (Ⅱ) form 2:1 complex. Furthermore, the extraction rate based on the volume of aqueous phase was obtained in a stirred vessel, and the rate equation was presented. Unfortunately, it was difficult to construct surfactant liquid membrane system by use of the present extractant.

  17. Extraction Mechanism of La3+ from Hydrochloric Acid Solution Using Cyanex 302

    Institute of Scientific and Technical Information of China (English)

    乌东北; 牛春吉; 李德谦

    2004-01-01

    The solvent extraction of La3+ from hydrochloric acid solutions was investigated using bis(2, 4, 4-trimethylpentyl) monothiophosphinic acid(Cyanex 302, HL) as an extractant. The effect of equilibrium of aqueous acidity on extraction of La3+ using Cyanex 302 in different diluents was discussed. The effects of extractant concentration and chloride ion on the extraction reaction were also studied. Stoichiometry of the extraction reactions and the nature of metal complexes formed were determined using slope analysis technique and IR measurement.

  18. Structure of water and the thermodynamics of aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Nemethy, G.

    1970-10-26

    This report represents the summary of a series of lectures held at the Istituto Superiore di Sanita, Laboratori di Fisica, from 18 September to 26 October 1970. The topics discussed were: Intermolecular forces, the individual water molecule and the hydrogen bond, the structures of the solid phases of water, experimental information on the strucuture of liquid water, theoretical models of water structure, experimental properties and theoretical models of aqueous solutions of nonpolar solutes, polar solutes, and electrolytes, the conformational stability of biological macromolecules.

  19. Conductivity of Oxalic Acid in Aqueous Solution at Low Concentration

    Institute of Scientific and Technical Information of China (English)

    倪良; 韩世钧

    2005-01-01

    Oxalic acid is a weak and unsymmetrical bi-basic acid. There exist dissociation and association equilibria among the species in aqueous solution. The molar conductivity of the solution is the sum of the ionic contributions.Based on this idea, a new prediction equation of ionic conductivity was proposed at low concentration. The molar conductivities of the solution and its relevant ions were calculated respectively. The results obtained were in good agreement with those from experiments and the Quint-Viallard equation.

  20. Electrochemical oxidation of pyrrhotute in aqueous solution

    Institute of Scientific and Technical Information of China (English)

    QIN Wen-qing; LI Quan; QIU Guan-zhou; XU Ben-jun

    2005-01-01

    The anodic surface oxidation of natural pyrrhotite in 0.3 mol/L KCl and HCl solution (pH 4. 0) and 0.1 mol/L Na2 B4O7 solution (pH 9.18) respectively was investigated by using cyclic voltammetry, Tafel plot, and chronoamperometry. In 0.3 mol/L KCl and HCl solution (pH 4.0), at potential less than 0.5 V(vs SHE), the production of anodic oxidation on pyrrhotite surface can not maintain a stable phase to form a passive film. In 0. 1 mol/L Na2B4 O7 solution (pH 9.18), when the electrode potential increases to more than 0.5 V (vs SHE), part of S is oxidized to sulfate, making the passive film somewhat porous, but elemental S and metal oxidates Fe(OH)3 still remain on the electrode surface, and the passive film can not be broken down totally. According to PARCalc Tafel analysis,the corresponding corrosion current density (J0) is 5.34 μA/cm2 , which is also the exchange current density of the oxidation reaction on pyrrhotite electrode surface in 0. 1 mol/L Na2B4O7 solution (pH 9.18). The electrochemical dynamics equation of the oxidation was determined.

  1. Gold and Silver Extraction from Leach Solutions

    Directory of Open Access Journals (Sweden)

    Bagdaulet K. Kenzhaliyev

    2014-03-01

    Full Text Available There has been carried out an investigation on the extraction of gold and silver from thiosulfate solutions: standard test and technological solutions of chemical and electrochemical leaching. The influence of related metals on the process of extracting gold from solution was studied. There has been conducted a comparative study of the IR spectra of solutions after the sorption of gold, silver and related metals.

  2. Molecular Weight and Aggregation of Erwinia Gum in Aqueous Solutions

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Erwinia(E) gum is composed of glucose, fucose, galactose and glucuronic acid. The weight-average molecular weights Mw, number-average molecular weights Mn and intrinsic viscosities[η] of the four fractions and the unfractionated E gum in aqueous solutions at desired temperatures were studied by light scattering, membrane osmometry, size exclusion chromatography(SEC) and viscometry. The experimental results prove that E gum formed aggregates in the aqueous solution at 25 ℃ and the aggregates were broken gradually with increasing temperature. The dissociation of the aggregates of E gum in the aqueous solution started at 36 ℃, and was completed at around 90 ℃. The [η] values of E gum and its fractions are much higher than those of the conventional polymers with the similar molecular weights, and decrease with increasing NaCl concentration.

  3. Oxidation of Hydrazine in Aqueous Solutions

    Science.gov (United States)

    1978-03-01

    mechanism is different in the two different temperature regions [ Levenspiel (Reference 21)]. Lurker (Reference 7) also observed that at 6°C a kinetic...and Bielski, B., Kinetic Systems: Mathematical Descriptions of Chemical Kinetics in Solution, Wiley Interscience, New York (1972). 21. Levenspiel , 0

  4. Preparation of stable aqueous solution of keratins, and physiochemical and biodegradational properties of films.

    Science.gov (United States)

    Yamauchi, K; Yamauchi, A; Kusunoki, T; Kohda, A; Konishi, Y

    1996-08-01

    A stable aqueous solution of reduced keratins was prepared by extracting the proteins from wool (Corriedale) with a mixture of urea, mercaptanol, surfactant, and water at 40-60 degrees C. Sodium dodecyl sulfate was especially effective as a surfactant, not only in promoting extraction but also in stabilizing the aqueous protein solution. The proteins had the following constants: MW, 52,000-69,000 daltons; cysteine content, 8-9 mol%; pl about 6.7. A clear film was readily prepared from a keratin solution containing glycerol. The film was insoluble in water and organic solvents including dimethyl sulfoxide. The keratin film was permeable to glucose, urea, and sodium chloride. The keratin film was degraded in vitro (by trypsin) and in vivo (by subcutaneous embedding in mice).

  5. Development of tropine-salt aqueous two-phase systems and removal of hydrophilic ionic liquids from aqueous solution.

    Science.gov (United States)

    Wu, Haoran; Yao, Shun; Qian, Guofei; Song, Hang

    2016-08-26

    A novel aqueous two-phase systems (ATPS) composed of a small molecule organic compound tropine and an organic or inorganic salt aqueous solution has been developed for the first time. The phase behavior of tropine-salt ATPS was systemically investigated and the phase equilibrium data were measured in different temperatures and concentrations and correlated by the Merchuk equation with satisfactory results. The detection of the conductivity and particle size proved the formation of micelle in the process of forming tropine-salt ATPS. The separation application of the ATPS was assessed with the removal of hydrophilic benzothiazolium-based ionic liquids (ILs) from aqueous solution. The result showed that ILs were effectively extracted into the top tropine-rich phase. Finally, ILs in the top tropine-rich phase were further separated by the means of adsorption-desorption with DM301 macroporous resin and ethanol. The method of novel tropine-salt ATPS combined with adsorption-desorption is demonstrated a promising alternative thought and approach for the removal or recovery of hydrophilic compounds from aqueous media and also could provide a potential application for bio-separation.

  6. Predicting accurate absolute binding energies in aqueous solution

    DEFF Research Database (Denmark)

    Jensen, Jan Halborg

    2015-01-01

    Recent predictions of absolute binding free energies of host-guest complexes in aqueous solution using electronic structure theory have been encouraging for some systems, while other systems remain problematic. In this paper I summarize some of the many factors that could easily contribute 1-3 kcal......-represented by continuum models. While I focus on binding free energies in aqueous solution the approach also applies (with minor adjustments) to any free energy difference such as conformational or reaction free energy differences or activation free energies in any solvent....

  7. A lithium ion battery using an aqueous electrolyte solution

    OpenAIRE

    Zheng Chang; Chunyang Li; Yanfang Wang; Bingwei Chen; Lijun Fu; Yusong Zhu; Lixin Zhang; Yuping Wu; Wei Huang

    2016-01-01

    Energy and environmental pollution have become the two major problems in today’s society. The development of green energy storage devices with good safety, high reliability, high energy density and low cost are urgently demanded. Here we report on a lithium ion battery using an aqueous electrolyte solution. It is built up by using graphite coated with gel polymer membrane and LISICON as the negative electrode, and LiFePO4 in aqueous solution as the positive electrode. Its average discharge vo...

  8. Ionisation constants of inorganic acids and bases in aqueous solution

    CERN Document Server

    Perrin, D D

    2013-01-01

    Ionisation Constants of Inorganic Acids and Bases in Aqueous Solution, Second Edition provides a compilation of tables that summarize relevant data recorded in the literature up to the end of 1980 for the ionization constants of inorganic acids and bases in aqueous solution. This book includes references to acidity functions for strong acids and bases, as well as details about the formation of polynuclear species. This text then explains the details of each column of the tables, wherein column 1 gives the name of the substance and the negative logarithm of the ionization constant and column 2

  9. Removal of Phosphate from Aqueous Solution with Modified Bentonite

    Institute of Scientific and Technical Information of China (English)

    唐艳葵; 童张法; 魏光涛; 李仲民; 梁达文

    2006-01-01

    Bentonite combined with sawdust and other metallic compounds was used to remove phosphate from aqueous solutions in this study. The adsorption characteristics of phosphate on the modified bentonite were investigated, including the effects of temperature, adsorbent dosage, initial concentration of phosphate and pH on removal of phosphate by conducting a series of batch adsorption experiments. The results showed that 98% of phosphate removal rate was obtained since sawdust and bentonite used in this investigation were abundantly and locally available. It is concluded that modified bentonite is a relatively efficient, low cost and easily available adsorbent for the removal of phosphate from aqueous solutions.

  10. Glasslike behavior in aqueous electrolyte solutions.

    Science.gov (United States)

    Turton, David A; Hunger, Johannes; Hefter, Glenn; Buchner, Richard; Wynne, Klaas

    2008-04-28

    When salts are added to water, generally the viscosity increases, suggesting that the ions increase the strength of the water's hydrogen-bond network. However, infrared pump-probe measurements on electrolyte solutions have found that ions have no influence on the rotational dynamics of water molecules, implying no enhancement or breakdown of the hydrogen-bond network. Here, we report optical Kerr effect and dielectric relaxation spectroscopic measurements, which have enabled us to separate the effects of rotational and transitional motions of the water molecules. These data show that electrolyte solutions behave like a supercooled liquid approaching a glass transition in which rotational and translational molecular motions are decoupled. It is now possible to understand previously conflicting viscosity data, nuclear magnetic resonance relaxation, and ultrafast infrared spectroscopy in a single unified picture.

  11. Glasslike Behavior in Aqueous Electrolyte Solutions

    CERN Document Server

    Turton, David A; Hefter, Glenn; Buchner, Richard; Wynne, Klaas; 10.1063/1.2906132

    2009-01-01

    When salts are added to water, the viscosity generally increases suggesting the ions increase the strength of the water's hydrogen-bond network. However, infrared pump-probe measurements on electrolyte solutions have found that ions have no influence on the rotational dynamics of water molecules implying no enhance-ment or breakdown of the hydrogen-bond network. Here we report optical Kerr-effect and dielectric relaxa-tion spectroscopic measurements, which have enabled us to separate the effects of rotational and transitional motions of the water molecules. These data show that electrolyte solutions behave like a supercooled liquid approaching a glass transition in which rotational and translational molecular motions are decoupled. It is now possible to understand previously conflicting viscosity data, nuclear magnetic resonance relaxation, and ultrafast infrared spectroscopy in a single unified picture.

  12. Aqueous extraction of pectin from sisal waste.

    Science.gov (United States)

    Santos, Jener David G; Espeleta, Alexandre F; Branco, Alexsandro; de Assis, Sandra A

    2013-02-15

    In this work, sisal waste was used as a source of pectin. Sisal is known worldwide as a source of hard fibres, and Brazil is the largest producer of sisal, producing more than 246,000 tonnes. However, the process of removing the fibres of the sisal leaf generates 95% waste. This study investigated the effect of the liquid/solid ratio (%), time (min), and temperature (°C) on the yield of the pectin obtained from sisal waste by attractive environmentally friendly process. A statistical Box-Behnken design was applied to determine the important effects and interactions of these independent variables on the yield of pectin, the dependent variable. Significant models were obtained. The yield of the extracted pectin ranged from 4.61 to 19.2%. The conditions that produced the highest yield (19.2%) were a temperature of 85 °C, extraction time of 60 min and a liquid/solid ratio of 2%.

  13. LIGHT SCATTERING OF POLYSACCHARIDE FROM LACQUER IN AQUEOUS SOLUTION

    Institute of Scientific and Technical Information of China (English)

    ZHANG Lina; DU Yumin; KUMANOTANI JU

    1989-01-01

    The polysaccharide having weight-average molecular weight Mw= 1. 09 × 105 , isolated from the sap of lac trees ( Vietnam ), was separated into 12 fractions by aqueous-phase preparative gel permeation chromatography. The molecular weights and molecular weight distributions of the fractions were measured in aqueous 0.08M KCl/0.01 M NaAc and 0.4M KCl/0.05M NaAc at pH = 7.6 by light scattering, viscometry and gel permeation chromatography. The Mark-Houwink equation in aqueous 0.08M KCl/0.01M NaAc at30 ℃ was found to be [ η] = 2.28 ×10-2 M0.52w ( cm3/g ), which indicated the polysaccharide chain in the aqueous solution to be a spherical random coil.

  14. Antibacterial Activity of Medicinal Aqueous Plant Extracts against Mycobacterium tuberculosis

    Directory of Open Access Journals (Sweden)

    Muna Mohammed Buzayan

    2012-09-01

    Full Text Available Tuberculosis (TB remains a serious health problem in many regions of the world, and the development of resistance to antibiotics by this microbe created the need for new drugs to replace those which have lost effectiveness. This study assesses the medicinal anti-Mycobacterium tuberculosis properties of natural products obtained from plants collected from Eastern Libya. In this study aqueous extracts of nine different plants were assayed for their Mycobacterium tuberculosis inhibitory activity using the BACTEC MGIT960 susceptibility test method. The aqueous extracts of Ceratonia siliqua L, Helichrysum stoechas (L. Moench and Thymus algeriensis did not show any activity against M. tuberculosis in different concentrations. The aqueous extract of Marrubium vulgare L. from Syria showed high activity against M. tuberculosis. Marrubium alysson L., Marrubium vulgare L., Pistacia lentiscus L, Quercus coccifera L, Thymus capitatus (L. Hoffm. & Link, showed varying degrees of activity against M. tuberculosis. The results of this study show that aqueous extracts from six different medicinal plants have different effects against M. tuberculosis in vitro.

  15. Photocatalytic degradation of molinate in aqueous solutions.

    Science.gov (United States)

    Bizani, E; Lambropoulou, D; Fytianos, K; Poulios, I

    2014-11-01

    In this study, the degradation of molinate through heterogeneous photocatalysis, using two different types of the semiconductor TiO2 as photocatalyst, as well as through homogeneous treatment, applying the photo-Fenton reaction, has been investigated. As far as heterogeneous photocatalysis is concerned, the degradation of the pesticide follows apparent first-order kinetics, while the type of the catalyst and the pH value of the solution affect the degradation rate. The effect of the addition of electron scavengers (H2O2 and K2S2O8) was also studied. In the case of photo-Fenton-assisted system, the degradation also follows pseudo-first-order kinetics. Parameters such as iron's and electron scavenger's concentration and inorganic ions strongly affect the degradation rate. The extent of pesticide mineralization was investigated using dissolved organic carbon (DOC) measurements. The toxicity of the treated solution was evaluated using the Microtox test based on the luminescent bacteria Vibrio fischeri. The detoxification and mineralization efficiency was found to be dependent on the system studied, and although it did not follow the rate of pesticide disappearance, it took place in considerable extent. The study of the photodegradation treatment was completed by the determination of the intermediate by-products formed during the process, which was carried out using LC-MS/MS technique and led to similar compounds with both processes.

  16. Optimising the Encapsulation of an Aqueous Bitter Melon Extract by Spray-Drying

    OpenAIRE

    Tan, Sing Pei; Kha, Tuyen Chan; Parks, Sophie; Stathopoulos, Costas; Paul D. Roach

    2015-01-01

    Our aim was to optimise the encapsulation of an aqueous bitter melon extract by spray-drying with maltodextrin (MD) and gum Arabic (GA). The response surface methodology models accurately predicted the process yield and retentions of bioactive concentrations and activity (R 2 > 0.87). The optimal formulation was predicted and validated as 35% (w/w) stock solution (MD:GA, 1:1) and a ratio of 1.5:1 g/g of the extract to the stock solution. The spray-dried powder had a high process yield (66.2% ...

  17. Optimising the Encapsulation of an Aqueous Bitter Melon Extract by Spray-Drying

    OpenAIRE

    Sing Pei Tan; Tuyen Chan Kha; Sophie Parks; Costas Stathopoulos; Paul D. Roach

    2015-01-01

    Our aim was to optimise the encapsulation of an aqueous bitter melon extract by spray-drying with maltodextrin (MD) and gum Arabic (GA). The response surface methodology models accurately predicted the process yield and retentions of bioactive concentrations and activity (R2 > 0.87). The optimal formulation was predicted and validated as 35% (w/w) stock solution (MD:GA, 1:1) and a ratio of 1.5:1 g/g of the extract to the stock solution. The spray-dried powder had a high process yield (66.2...

  18. Permeability in a state of partial solidification of aqueous solution

    Science.gov (United States)

    Okada, Masashi; Kang, Chaedong; Okiyama, Haruhiko

    A mushy region was formed by solidifying NaCl aqueous solution in a circular tube or a rectangular tube. The measurements of permeability were performed by changing volume fraction of liquid region in the mushy region. The dendritic ice in the solidification process was observed with a CCD microscope. The following results were obtained. The permeability increases with the volume fraction of liquid phase, and decreases with increasing the super-cooling degree of the solution or increasing the initial concentration of the solution, and is constant after the mushy region was formed. The arm space of dendrite becomes narrower as the super-cooling degree of the solution increases.

  19. Radiolysis of paracetamol in dilute aqueous solution

    Science.gov (United States)

    Szabó, László; Tóth, Tünde; Homlok, Renáta; Takács, Erzsébet; Wojnárovits, László

    2012-09-01

    Using radiolytic experiments hydroxyl radical (main reactant in advanced oxidation processes) was shown to effectively destroy paracetamol molecules. The basic reaction is attachment to the ring. The hydroxy-cyclohexadienyl radical produced in the further reactions may transform to hydroxylated paracetamol derivatives or to quinone type molecules and acetamide. The initial efficiency of aromatic ring destruction in the absence of dissolved O2 is c.a. 10%. The efficiency is 2-3 times higher in the presence of O2 due to its reaction with intermediate hydroxy-cyclohexadienyl radical and the subsequent ring destruction reactions through peroxi radical. Upon irradiation the toxicity of solutions at low doses increases with the dose and then at higher doses it decreases. This is due to formation of compounds with higher toxicity than paracetamol (e.g. acetamide, hidroquinone). These products, however, are highly sensitive to irradiation and degrade easily.

  20. Solubility of carbon dioxide in aqueous piperazine solutions

    NARCIS (Netherlands)

    Derks, P. W. J.; Dijkstra, H. B. S.; Hogendoorn, J. A.; Versteeg, G. F.

    2005-01-01

    In the present work, new experimental data are presented on the solubility of carbon dioxide in aqueous piperazine solutions, for concentrations of 0.2 and 0.6 molar piperazine and temperatures of 25, 40, and 70°C respectively. The present data, and other data available in the literature, were corr

  1. Rheological properties of silica suspensions in aqueous cellulose derivatives solutions

    Science.gov (United States)

    Ryo, Y.; Kawaguchi, M.

    1992-05-01

    The rheological properties of the silica suspensions in aqueous solutions of hydroxypropylmethylcellulose (HPMC) were investigated in terms of the shear stress and storage and loss moduli (G' and G`) as a function of silica content, HPMC concentration, and HPMC molecular weight by using a coaxial cylinder rheometer.

  2. Oscillometric and conductometric analysis of aqueous and organic dosimeter solutions

    DEFF Research Database (Denmark)

    Kovacs, A.; Slezsak, I.; McLaughlin, W.L.;

    1995-01-01

    ''conductometric'' electrodes and the study of the effect of frequency on the sensitivity of the method. On the basis of these investigations an oscillometric reader has been designed and tested. The same evaluation methods have been tested on the irradiated aqueous alanine solutions, aiming also at the study...

  3. Adsorptive removal of antibiotics from aqueous solution using carbon materials.

    Science.gov (United States)

    Yu, Fei; Li, Yong; Han, Sheng; Ma, Jie

    2016-06-01

    Antibiotics, an important type of environmental contamination, have attracted many researchers to the study of their removal from aqueous solutions. Adsorption technology is a fast, efficient, and economical physicochemical method that is extensively used in wastewater treatment. From original activated carbon and carbon nanotubes to the latest graphene-based materials, carbon-based materials have been widely used as highly effective adsorbents for contaminant removal from aqueous solution because of their large specific surface area, high porosity, and high reaction activity. In this article, adsorption removal methods for four major types of antibiotic (tetracyclines, sulfonamides, macrolides, and quinolones) are reviewed. We also provide an overview of the application development of carbon materials as adsorbents for antibiotic removal from aqueous solution. The most promising works are discussed, and the main challenges in preparing high-performance adsorbents and the development tendency of adsorbents are also analyzed. This work provides theoretical guidance for subsequent research in the design and modification of carbon materials for applications in the adsorption removal of antibiotics from aqueous solution.

  4. CATALYSIS BY SURFACTANT AGGREGATES IN AQUEOUS-SOLUTIONS

    NARCIS (Netherlands)

    ENGBERTS, JBFN

    1992-01-01

    Catalysis of organic reactions by unfunctionalized surfactant aggregates (micelles, vesicles) in aqueous solution is largely determined by medium effects induced at the micellar binding sites and by entropy effects due to compartimentalization. The efficiency of these catalytic effects responds to c

  5. Kinetics of absorption of carbon dioxide in aqueous piperazine solutions

    NARCIS (Netherlands)

    Derks, P. W. J.; Kleingeld, T.; van Aken, C.; Hogendoorn, J. A.; Versteeg, G. F.

    2006-01-01

    In the present work the absorption of carbon dioxide into aqueous piperazine (PZ) solutions has been studied in a stirred cell, at low to moderate temperatures, piperazine concentrations ranging from 0.6 to 1.5 kmol m- 3, and carbon dioxide pressures up to 500 mbar, respectively. The obtained experi

  6. DETERMINATION OF CHLORHEXIDINE IN SALIVA AND IN AQUEOUS-SOLUTIONS

    NARCIS (Netherlands)

    de Vries, J.; Ruben, J; Arends, J.

    1991-01-01

    A new method is presented for the determination of chlorhexidine in centrifuged saliva and in aqueous solutions by means of fluorescence spectroscopy. The method relies on complex formation between chlorhexidine and eosin. The fluorescence value of the chlorhexidine-eosin system decreases with incre

  7. Colorimetric and fluorescent detection of biological thiols in aqueous solution

    Institute of Scientific and Technical Information of China (English)

    Yin-Hui Li; Jin-Feng Yang; Chang-Hui Liu; Ji-Shan Li; Rong-Hua Yang

    2013-01-01

    A new colorimetric and fluorescent probe,2-(2,4-dinitrostyryl)-1,3,3-trimethyl-3H-indolium iodide (DTI),for selective and sensitive detection of biological thiols is reported.In aqueous solution at physiological pH 7.4,biological thiols react with DTI via Michael addition to give the brownish red adduct concomitant with fluorescence emission decrease.

  8. Adsorption of lead ions from aqueous solutions using clinoptilolite

    OpenAIRE

    Golomeova, Mirjana; Zendelska, Afrodita; Krstev, Boris; Golomeov, Blagoj; Blažev, Krsto; Krstev, Aleksandar

    2014-01-01

    The adsorption of lead ions from synthetic aqueous solutions was performed by using natural zeolite (clinoptilolite). In order to determine the effectivity of clinoptilolite a series of experiments were performed under batch conditions from single ion solutions. Experiments were carried out at different initial concentration of lead ions, different initial pH values and different adsorbent mass. The adsorption kinetics is reasonably fast. It means that in the first 20 min approximately 90...

  9. Removal of azo dye from aqueous solutions using chitosan

    Directory of Open Access Journals (Sweden)

    Zuhair Jabbar

    2014-06-01

    Full Text Available Adsorption of Congo Red (CR from aqueous solution onto chitosan was investigated in a batch system. The effects of solution pH, initial dye concentration, and temperature were studied. Results indicated that chitosan could be used as a biosorbent to remove the azo dyes from contaminated water. Synthesize of chitosan involved three main stages as preconditioning, demineralization, deproteinization and deacetylation. Chitosan was characterized using Fourier Transform Infrared Spectroscopy (FTIR and solubility in 1% acetic acid.

  10. The effects of electrolysis on operational solutions in electromembrane extraction: The role of acceptor solution.

    Science.gov (United States)

    Kubáň, Pavel; Boček, Petr

    2015-06-12

    Fundamental operational principle and instrumental set-up of electromembrane extraction (EME) suggest that electrolysis may play an important role in this recently developed micro-extraction technique. In the present study, the effect of electrolysis in EME is described comprehensively for the first time and it is demonstrated that electrolysis considerably influences EME performance. Micro-electromembrane extraction (μ-EME) across free liquid membrane formed by 1-pentanol was utilized for real-time monitoring of the electrolytically induced changes in composition of μ-EME solutions. These changes were visualized with a set of acid-base indicators. Changes in colours of their aqueous solutions revealed serious variations in their pH values, which occurred within seconds to minutes of the μ-EME process. Variations of up to eight pH units were observed for indicator solutions initially prepared in 1, 5 and 10mM hydrochloric acid. No or only negligible pH changes (less than 0.15 pH unit) were observed for indicator solutions prepared in 50 and 100mM acetic acid demonstrating that initial composition of the aqueous solutions was the crucial parameter. These results were also confirmed by theoretical calculations of maximum pH variations in the solutions, which were based on total electric charge transfers measured in the μ-EME systems, and by exact measurements of their pH values after μ-EMEs. Acceptor solutions that, in the current practice, consist predominantly of low concentrations of strong mineral acids or alkali hydroxides may thus not always ensure adequate EME performance, which was manifested by decrease in extraction recoveries of a basic drug papaverine. A suitable remedy to the observed effects is the application of acceptor solutions containing high concentrations of weak acids or bases. These solutions not only eliminate the decrease in recoveries but also serve well as matrices of extracted samples for subsequent analysis by capillary

  11. Efficacy of an aqueous Pelargonium sidoides extract against herpesvirus.

    Science.gov (United States)

    Schnitzler, P; Schneider, S; Stintzing, F C; Carle, R; Reichling, J

    2008-12-01

    The compounds of an aqueous root extract of the African medicinal plant Pelargonium sidoides were analysed by LC-MS spectroscopy and the antiviral effect of this extract against herpes simplex virus was examined in cell culture. Besides predominant coumarins, simple phenolic structures as well as flavonoid and catechin derivatives were identified as major constituents in the Pelargonium extract. The inhibitory activity of this extract against herpes simplex virus type 1 (HSV-1) and herpes simplex virus type 2 (HSV-2) was tested in vitro on RC-37 cells using a plaque reduction assay and exhibited high antiviral activity against both herpesviruses in viral suspension tests. The 50% inhibitory concentration (IC(50)) of the aqueous Pelargonium sidoides extract for herpes simplex virus plaque formation was determined at 0.00006% and 0.000005% for HSV-1 and HSV-2, respectively. At maximum noncytotoxic concentrations of the extract, plaque formation was significantly reduced by more than 99.9% for HSV-1 and HSV-2 and a clear concentration-dependent antiviral activity against HSV could be demonstrated for this extract. In order to determine the mode of antiviral action, the extract was added at different times to the cells or viruses during the infection cycle. Both herpesviruses were significantly inhibited when pretreated with the plant extract or when the extract was added during the adsorption phase, whereas acyclovir demonstrated antiviral activity only intracellularly during replication of HSV. These results indicate that P. sidoides extract affected the virus before penetration into the host cell and reveals a different mode of action when compared to the classical drug acyclovir. Hence this extract is capable of exerting an antiviral effect on herpes simplex virus and might be suitable for topical therapeutic use as antiviral drug both in labial and genital herpes infection.

  12. Characterization of reaction products of iron and iron salts and aqueous plant extracts

    Energy Technology Data Exchange (ETDEWEB)

    Jaen, J.A. [Universidad de Panama, Centro de Investigaciones con Tecnicas Nucleares/Depto. de Quimica (Panama); Garcia de Saldana, E.; Hernandez, C. [Universidad de Panama, Maestria en Ciencias Quimicas (Panama)

    1999-11-15

    The complexes formed in aqueous solution as a result of a reaction of iron and iron salts (Fe{sup 2+} and Fe{sup 3+}) and some plant extracts were analyzed using Moessbauer spectroscopy and Fourier transform infrared. The extracts were obtained from Opuntia elatior mill., Acanthocereus pentagonus (L.) Britton, Mimosa tenuiflora, Caesalpinia coriaria (Jacq.) Willd., Bumbacopsis quinata (Jacq.) Dugand and Acacia mangium Willd., plants growing wildly in different zones of the Isthmus of Panama. Results suggest the formation of mono- and bis-type complexes, and in some cases, the occurrence of a redox reaction. The feasibility of application of the studied extracts as atmospheric corrosion inhibitors is discussed.

  13. Characterization of reaction products of iron and iron salts and aqueous plant extracts

    Science.gov (United States)

    Jaén, J. A.; García de Saldaña, E.; Hernández, C.

    1999-11-01

    The complexes formed in aqueous solution as a result of a reaction of iron and iron salts (Fe2+ and Fe3+) and some plant extracts were analyzed using Mössbauer spectroscopy and Fourier transform infrared. The extracts were obtained from Opuntia elatior mill., Acanthocereus pentagonus (L.) Britton, Mimosa tenuiflora, Caesalpinia coriaria (Jacq.) Willd., Bumbacopsis quinata (Jacq.) Dugand and Acacia mangium Willd., plants growing wildly in different zones of the Isthmus of Panama. Results suggest the formation of mono- and bis-type complexes, and in some cases, the occurrence of a redox reaction. The feasibility of application of the studied extracts as atmospheric corrosion inhibitors is discussed.

  14. Phytoremediation of Heavy Metals in Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Felix Aibuedefe AISIEN

    2010-12-01

    Full Text Available One of the major environmental problems is the pollution of water and soil by toxic heavy metals. This study investigated the phytoremediation potential of water hyacinth, for the removal of cadmium (Cd, lead (Pb and zinc (Zn. Water hyacinths were cultured in bore-hole water, supplemented with 5mg/l of Zn and Pb and 1mg/l of Cd at pH 4.5, 6.8 and 8.5. The plants were separately harvested each week for six weeks. The results showed that removal of these metals from solution was fast especially in the first two weeks, after which it became gradual till saturation point was reached. The accumulation of Cd and Zn in leaves and roots increased with increase in pH. The highest accumulation was in the roots with metal concentration of 4870mg/kg, 4150mg/kg and 710mg/kg for Zn, Pb and Cd respectively at pH 8.5. The maximum values of bioconcentration factor (BCF for Zn, Pb and Cd were 1674, 1531 and 1479 respectively, suggesting that water hyacinth was good accumulator of Zn, Pb and Cd, and could be used to treat industrial wastewater contaminated with heavy metals such as Zn, Pb and Cd.

  15. Block copolymer membranes for aqueous solution applications

    KAUST Repository

    Nunes, Suzana Pereira

    2016-03-22

    Block copolymers are known for their intricate morphology. We review the state of the art of block copolymer membranes and discuss perspectives in this field. The main focus is on pore morphology tuning with a short introduction on non-porous membranes. The two main strategies for pore formation in block copolymer membranes are (i) film casting and selective block sacrifice and (ii) self-assembly and non-solvent induced phase separation (SNIPS). Different fundamental aspects involved in the manufacture of block copolymer membranes are considered, including factors affecting the equilibrium morphology in solid films, self-assembly of copolymer in solutions and macrophase separation by solvent-non-solvent exchange. Different mechanisms are proposed for different depths of the SNIPS membrane. Block copolymer membranes can be prepared with much narrower pore size distribution than homopolymer membranes. Open questions and indications of what we consider the next development steps are finally discussed. They include the synthesis and application of new copolymers and specific functionalization, adding characteristics to respond to stimuli and chemical environment, polymerization-induced phase separation, and the manufacture of organic-inorganic hybrids.

  16. Assembly of DNA Architectures in a Non-Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Thomas J. Proctor

    2012-08-01

    Full Text Available In the present work, the procedures for the creation of self-assembled DNA nanostructures in aqueous and non-aqueous media are described. DNA-Surfactant complex formation renders the DNA soluble in organic solvents offering an exciting way to bridge the transition of DNA origami materials electronics applications. The DNA retains its structural features, and these unique geometries provide an interesting candidate for future electronics and nanofabrication applications with potential for new properties. The DNA architectures were first assembled under aqueous conditions, and then characterized in solution (using circular dichroism (CD spectroscopy and on the surface (using atomic force microscopy (AFM. Following aqueous assembly, the DNA nanostructures were transitioned to a non-aqueous environment, where butanol was chosen for optical compatibility and thermal properties. The retention of DNA hierarchical structure and thermal stability in non-aqueous conditions were confirmed via CD spectroscopy. The formation and characterization of these higher order DNA-surfactant complexes is described in this paper.

  17. Critical droplet theory explains the glass formability of aqueous solutions.

    Science.gov (United States)

    Warkentin, Matthew; Sethna, James P; Thorne, Robert E

    2013-01-04

    When pure water is cooled at ~10(6) K / s, it forms an amorphous solid (glass) instead of the more familiar crystalline phase. The presence of solutes can reduce this required (or "critical") cooling rate by orders of magnitude. Here, we present critical cooling rates for a variety of solutes as a function of concentration and a theoretical framework for understanding these rates. For all solutes tested, the critical cooling rate is an exponential function of concentration. The exponential's characteristic concentration for each solute correlates with the solute's Stokes radius. A modification of critical droplet theory relates the characteristic concentration to the solute radius and the critical nucleation radius of ice in pure water. This simple theory of ice nucleation and glass formability in aqueous solutions has consequences for general glass-forming systems, and in cryobiology, cloud physics, and climate modeling.

  18. An efficient petiole-feeding bioassay for introducing aqueous solutions into dicotyledonous plants.

    Science.gov (United States)

    Lin, Yu-Hsiang; Lin, Meng-Han; Gresshoff, Peter M; Ferguson, Brett J

    2011-01-01

    Introducing bioactive molecules into plants helps establish their roles in plant growth and development. Here we describe a simple and effective petiole-feeding protocol to introduce aqueous solutions into the vascular stream and apoplast of dicotyledonous plants. This 'intravenous feeding' procedure has wide applicability to plant physiology, specifically with regard to the analysis of source-sink allocations, long-distance signaling, hormone biology and overall plant development. In comparison with existing methods, this technique allows the continuous feeding of aqueous solutions into plants without the need for constant monitoring. Findings are provided from experiments using soybean plants fed with a range of aqueous solutions containing tracer dyes, small metabolites, radiolabeled chemicals and biologically active plant extracts controlling nodulation. Typically, feeding experiments consist of (i) generating samples to feed (extracts, solutions and so on); (ii) growing recipient plants; (iii) setting up the feeding apparatus; and (iv) feeding sample solutions into the recipient plants. When the plants are ready, the feeding procedure can take 1-3 h to set up depending on the size of experiment (not including preparation of materials). The petiole-feeding technique also works with other plant species, including tomato, chili pepper and cabbage plants, as demonstrated here.

  19. Raman spectra of amino acids and their aqueous solutions

    Science.gov (United States)

    Zhu, Guangyong; Zhu, Xian; Fan, Qi; Wan, Xueliang

    2011-03-01

    Amino acids are the basic "building blocks" that combine to form proteins and play an important physiological role in all life-forms. Amino acids can be used as models for the examination of the importance of intermolecular bonding in life processes. Raman spectra serve to obtain information regarding molecular conformation, giving valuable insights into the topology of more complex molecules (peptides and proteins). In this paper, amino acids and their aqueous solution have been studied by Raman spectroscopy. Comparisons of certain values for these frequencies in amino acids and their aqueous solutions are given. Spectra of solids when compared to those of the solute in solution are invariably much more complex and almost always sharper. We present a collection of Raman spectra of 18 kinds of amino acids ( L-alanine, L-arginine, L-aspartic acid, cystine, L-glutamic acid, L-glycine, L-histidine, L-isoluecine, L-leucine, L-lysine, L-phenylalanine, L-methionone, L-proline, L-serine, L-threonine, L-tryptophan, L-tyrosine, L-valine) and their aqueous solutions that can serve as references for the interpretation of Raman spectra of proteins and biological materials.

  20. Solid-like mechanical behaviors of ovalbumin aqueous solutions.

    Science.gov (United States)

    Ikeda, S; Nishinari, K

    2001-04-12

    Flow and dynamic mechanical properties of ovalbumin (OVA) aqueous solutions were investigated. OVA solutions exhibited relatively large zero-shear viscosity values under steady shear flow and solid-like mechanical responses against oscillating small shear strains, that is, the storage modulus was always larger than the loss modulus in the examined frequency range (0.1--100 rad s(-1)). These results suggest that dispersed OVA molecules arranged into a colloidal crystal like array stabilized by large interparticle repulsive forces. However, marked solid-like mechanical behaviors were detected even when electrostatic repulsive forces among protein molecules were virtually absent, which could not be explained solely on the basis of conventional Derjaguin--Landau--Verwey--Overbeek (DLVO) theory. Large non-DLVO repulsive forces seem to stabilize native OVA aqueous solutions.

  1. Adsorption of EDTA on activated carbon from aqueous solutions.

    Science.gov (United States)

    Zhu, Hai-song; Yang, Xiao-juan; Mao, Yan-peng; Chen, Yu; Long, Xiang-li; Yuan, Wei-kang

    2011-01-30

    In this study, the adsorption of EDTA on activated carbon from aqueous solutions has been investigated in a batch stirred cell. Experiments have been carried out to investigate the effects of temperature, EDTA concentration, pH, activated carbon mass and particle size on EDTA adsorption. The experimental results manifest that the EDTA adsorption rate increases with its concentration in the aqueous solutions. EDTA adsorption also increases with temperature. The EDTA removal from the solution increases as activated carbon mass increases. The Langmuir and Freundlich equilibrium isotherm models are found to provide a good fitting of the adsorption data, with R(2) = 0.9920 and 0.9982, respectively. The kinetic study shows that EDTA adsorption on the activated carbon is in good compliance with the pseudo-second-order kinetic model. The thermodynamic parameters (E(a), ΔG(0), ΔH(0), ΔS(0)) obtained indicate the endothermic nature of EDTA adsorption on activated carbon.

  2. Molecular mechanism of the viscosity of aqueous glucose solutions

    Science.gov (United States)

    Bulavin, L. A.; Zabashta, Yu. F.; Khlopov, A. M.; Khorol'skii, A. V.

    2017-01-01

    Experimental relations are obtained for the viscosity of aqueous glucose solutions in the temperature range of 10-80°C and concentration range 0.01-2.5%. It is found that the concentration dependence of fluidity is linear when the concentration is higher than a certain value and varies at different temperatures. The existence of such a dependence indicates that the mobilities of solvent and solute molecules are independent of the concentration of solutions. This assumption is used to construct a theoretical model, in which the structure of an aqueous glucose solution is presented as a combination of two weakly interacting networks formed by hydrogen bonds between water molecules and between glucose molecules. Theoretical relations are obtained using this model of network solution structure for the concentration and temperature dependence of solution viscosity. Experimental data are used to calculate the activation energies for water ( U w = 3.0 × 10-20 J) and glucose molecules ( U g = 2.8 × 10-20 J). It is shown that the viscosity of a solution in such a network structure is governed by the Brownian motion of solitons along the chains of hydrogen bonds. The weak interaction between networks results in the contributions to solution fluidity made by the motion of solitons in both of them being almost independent.

  3. Adsorption of Chromium(VI) from Aqueous Solutions by Coffee Polyphenol-Formaldehyde/Acetaldehyde Resins

    OpenAIRE

    2013-01-01

    Removal of chromium(VI) from wastewater is essential as it is toxic. Thus, removal of chromium(VI) was performed using coffee polyphenol-formaldehyde/acetaldehyde resins as adsorbents. Adsorbent resins were prepared by condensation of decaffeinated coffee powder with formaldehyde/acetaldehyde and used for the removal of Cr(VI) ions from aqueous solutions. A simple and sensitive solid phase extraction procedure was applied for the determination of chromium at trace levels by spectroscopic meth...

  4. Direct hydride derivatization of methyl- and ethylmercury chlorides in aqueous solution with KBH4

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    A convenient hydride derivatization procedure of methyl-and ethylmercury chlorides to volatile hydrides was reported. In sealed vials methylmercury and ethylmercury compounds in acidic aqueous solutions were converted into their volatile forms by the reaction with potassium tetrahydroborate(KBH4) and elvolved to the headspace of the vials. The gaseous analytes in the headspace were extracted and concentrated by solid phase microextraction(SPME) and injected into gas chromatography (GC) for separation and identified by mass selective detector(MS).

  5. Spontaneous Oligomerization of Nucleotide Alternatives in Aqueous Solutions

    Science.gov (United States)

    Smith, Karen E.; House, Christopher H.; Dworkin, Jason P.; Callahan, Michael P.

    2017-03-01

    On early Earth, a primitive polymer that could spontaneously form from likely available precursors may have preceded both RNA and DNA as the first genetic material. Here, we report that heated aqueous solutions containing 5-hydroxymethyluracil (HMU) result in oligomers of uracil, heated solutions containing 5-hydroxymethylcytosine (HMC) result in oligomers of cytosine, and heated solutions containing both HMU and HMC result in mixed oligomers of uracil and cytosine. Oligomerization of hydroxymethylated pyrimidines, which may have been abundant on the primitive Earth, might have been important in the development of simple informational polymers.

  6. Immunosuppressive activity of an aqueous Viola tricolor herbal extract

    Science.gov (United States)

    Sauer, Barbara; Huber, Roman; Gruber, Christian W.; Gründemann, Carsten

    2014-01-01

    Ethnopharmacological relevance Heartsease (Viola tricolor L.), a member of the Violaceae family, has a long history as a medicinal plant and has been documented in the Pharmacopoeia of Europe. Due to its anti-inflammatory properties it is regarded as a traditional remedy against skin diseases, for example for the treatment of scabs, itching, ulcers, eczema or psoriasis, and it is also used in the treatment of inflammation of the lungs and chest such as bronchitis or asthma. Because T-cells play an important role in the pathological process of inflammatory diseases we investigated the effect of an aqueous Viola extract on lymphocyte functions and explored the ‘active’ principle of the extract using bioactivity-guided fractionation. Material and Methods An aqueous Viola extract was prepared by C18 solid-phase extraction. Effects on proliferation of activated lymphocytes (using the cell membrane permeable fluorescein dye CFSE), apoptosis and necrosis (using annexin V and propidium iodide staining), interleukin-2 (IL-2) receptor expression (using fluorochrome-conjugated antibodies) and IL-2 cytokine secretion (using an ELISA-based bead array system) were measured by flow cytometry. Influence on lymphocyte polyfunctionality was characterized by Viola extract-induced production of IFN-γ and TNF-α, as well as its influence on lymphocyte degranulation activity. Fractionation and phytochemical analysis of the extract were performed by RP-HPLC and mass spectrometry. Results The aqueous Viola extract inhibited proliferation of activated lymphocytes by reducing IL-2 cytokine secretion without affecting IL-2 receptor expression. Similarly, effector functions were affected as indicated by the reduction of IFN-γ and TNF-α production; degranulation capacity of activated lymphocytes remained unaffected. Bioassay-guided fractionation and phytochemical analysis of the extract led to identification of circular plant peptides, so called cyclotides, as bioactive components

  7. Antioxidant status of dog aqueous humor after extracapsular lens extraction

    Directory of Open Access Journals (Sweden)

    Barros P.S.M.

    2003-01-01

    Full Text Available We determined the antioxidant status of the aqueous humor after extracapsular lens extraction in 14 mongrel dogs weighing about 10 kg. The animals were examined by slit lamp biomicroscopy, applanation tonometry and indirect ophthalmoscopy. One eye was submitted to conventional extracapsular lens extraction and the other was used as control. Samples of aqueous humor were obtained by anterior chamber paracentesis before and at days 1, 2, 3, 7 and 15 after surgery. Total antioxidant status was determined as the capacity of aqueous humor to inhibit free radical generation by 2,2-azobis(2-amidopropane chlorine. Ascorbic acid concentration was measured by HPLC with UV detection. Protein content was determined with the biuret reagent. Statistical analysis was performed by ANOVA followed by the Tukey-Kramer test. Protein concentration increased from 0.61 to 22 mg/ml 24 h after surgery. These levels were maintained and returned to normal at day 7. Total antioxidant capacity was reduced from 50 to about 30 min until day 3 and at day 7 it was equal to control. Ascorbic acid levels were reduced from 252 to about 110 µM and then returned to control values at day 15. Considering the importance of ascorbic acid concentration in aqueous humor for the maintenance of the antioxidant status of the anterior segment of the eye, the decrease of antioxidant defenses suggests that the surgical procedures promote an oxidative stress condition in the eye.

  8. Dephosphorization of Steelmaking Slag by Leaching with Acidic Aqueous Solution

    Science.gov (United States)

    Qiao, Yong; Diao, Jiang; Liu, Xuan; Li, Xiaosa; Zhang, Tao; Xie, Bing

    2016-09-01

    In the present paper, dephosphorization of steelmaking slag by leaching with acidic aqueous solution composed of citric acid, sodium hydroxide, hydrochloric acid and ion-exchanged water was investigated. The buffer solution of C6H8O7-NaOH-HCl system prevented changes in the pH values. Kinetic parameters including leaching temperature, slag particle size and pH values of the solution were optimized. The results showed that temperature has no obvious effect on the dissolution ratio of phosphorus. However, it has a significant effect on the dissolution ratio of iron. The dephosphorization rate increases with the decrease of slag particle size and the pH value of the solution. Over 90% of the phosphorus can be dissolved in the solution while the corresponding leaching ratio of iron was only 30% below the optimal condition. Leaching kinetics of dephosphorization follow the unreacted shrinking core model with a rate controlled step by the solid diffusion layer, the corresponding apparent activation energy being 1.233 kJ mol-1. A semiempirical kinetic equation was established. After leaching, most of the nC2S-C3P solid solution in the steelmaking slag was selectively dissolved in the aqueous solution and the iron content in the solid residue was correspondingly enriched.

  9. Antinociceptive activity of Mentha piperita leaf aqueous extract in mice

    Directory of Open Access Journals (Sweden)

    Yousef A. Taher

    2012-03-01

    Full Text Available Mentha piperita L. (Labiatae is an herbaceous plant, used in folk medicine for the treatment of several medical disorders.In the present study, the aqueous extract of Mentha piperita leaf, at the i.p doses 200 and 400 mg/kg, showed significant analgesic effects against both acetic acid-induced writhing and hot plate-induced thermal stimulation in mice, with protection values of 51.79% and 20.21% respectively. On the contrary, the Mentha piperita leaf aqueous extract did not exhibit anti-inflammatory activity against carrageenan induced paw oedema.These findings indicate that Mentha piperita has a potential analgesic effect that may possibly have mediated centrally and peripherally, as well as providing a pharmacological evidence for its traditional use as a pain reliever.

  10. Rheological properties of novel thermo-responsive polycarbonates aqueous solutions

    Institute of Scientific and Technical Information of China (English)

    王月霞; 谭业邦; 黄晓玲

    2008-01-01

    Thermo-responsive multiblock polycarbonates were facilely synthesized by covalently binding poly(ethylene glycol)(PEG) and poly(propylene glycol)(PPG) blocks,using triphosgene as coupling agent and pyridine as catalyst.The aqueous solutions of thermo-responsive polycarbonates were investigated by rheological measurements.Steady-state shear measurements reveal that the polycarbonate solutions exhibit shear-thinning behavior and the hydrophilic content has a pronounced effect on the flow behavior of the polycarbonates aqueous solutions.The shear viscosity decreases with increasing poly(ethylene oxide)(PEO) composition.The increase of viscosity with increasing concentration is probably attributed to the formation of stronger network owing to interchain entanglement of PEO block at higher concentration.When the flow curves are fitted to the power law model,flow index is obtained to be less than 1,as exhibiting typical pesudoplastic fluid.The viscoelastic properties of the system also show close dependence on the composition of polycarbonates.Temperature sweep confirms that the multiblock polycarbonates exhibit thermo-responsive properties.For 7% aqueous solution of polycarbonate with composition ratio of EO to PO of 1/1,the sol-gel transition occurs at 37 ℃,which makes the system suitable as an injectable drug delivery system.

  11. Large Angular Jump Mechanism Observed for Hydrogen Bond Exchange in Aqueous Perchlorate Solution

    Energy Technology Data Exchange (ETDEWEB)

    Ji, Minbiao; /SLAC, PULSE /Stanford U., Phys. Dept.; Odelius3, Michael; /Stockholm U.; Gaffney1, K.J.; /aff SLAC, PULSE

    2010-06-11

    The mechanism for hydrogen bond (H-bond) switching in solution has remained subject to debate despite extensive experimental and theoretical studies. We have applied polarization-selective multidimensional vibrational spectroscopy to investigate the H-bond exchange mechanism in aqueous NaClO{sub 4} solution. The results show that a water molecule shifts its donated H-bonds between water and perchlorate acceptors by means of large, prompt angular rotation. Using a jump-exchange kinetic model, we extract an average jump angle of 49 {+-} 4{sup o}, in qualitative agreement with the jump angle observed in molecular dynamics simulations of the same aqueous NaClO{sub 4} solution.

  12. Fermentation of aqueous plant seed extracts by lactic acid bacteria

    Energy Technology Data Exchange (ETDEWEB)

    Schafner, D.W.; Beuchat, R.L.

    1986-05-01

    The effects of lactic acid bacterial fermentation on chemical and physical changes in aqueous extracts of cowpea (Vigna unguiculata), peanut (Arachis hypogea), soybean (Glycine max), and sorghum (Sorghum vulgare) were studied. The bacteria investigated were Lactobacillus helveticus, L. delbrueckii, L. casei, L. bulgaricus, L. acidophilus, and Streptococcus thermophilus. Organisms were inoculated individually into all of the seed extracts; L. bulgaricus and S. thermophilus were also evaluated together as inocula for fermenting the legume extracts. During fermentation, bacterial population and changes in titratable acidity, pH, viscosity, and color were measured over a 72 h period at 37 degrees C. Maximum bacterial populations, titratable acidity, pH, and viscosity varied depending upon the type of extract and bacterial strain. The maximum population of each organism was influenced by fermentable carbohydrates, which, in turn, influenced acid production and change in pH. Change in viscosity was correlated with the amount of protein and titratable acidity of products. Color was affected by pasteurization treatment and fermentation as well as the source of extract. In the extracts inoculated simultaneously with L. bulgaricus and S. thermophilus, a synergistic effect resulted in increased bacterial populations, titratable acidity, and viscosity, and decreased pH in all the legume extracts when compared to the extracts fermented with either of these organisms individually. Fermented extracts offer potential as substitutes for cultured dairy products. 24 references.

  13. Properties of vermicompost aqueous extracts prepared under different conditions.

    Science.gov (United States)

    Hanc, Ales; Boucek, Jiri; Svehla, Pavel; Dreslova, Marketa; Tlustos, Pavel

    2016-09-23

    The aim of this work was to determine the influence of aeration and time of extraction on the agrochemical properties of aqueous extracts from vermicomposts made from horse manure (M) and apple pomace (P) waste. There were two extract treatments: stirring without aeration (S), and stirring with aeration (A) for 48 h. Aeration significantly increased the levels of electrical conductivity (EC) and the concentration of [Formula: see text], [Formula: see text], and macro-elements in the extracts. In the (A) treatment, the extraction efficiency of K and Mg increased twofold, and the extraction efficiency of Ca and P increased by one-third compared with the (S) treatment. Simultaneously, the extracts prepared under aeration were characteristic with a higher pH value compared with non-aerated variants. The EC and content of macro-elements in the extracts increased proportionally with time. Their highest growth was found within the first 6 h. After 48 h, the highest release of macro-elements into the extract was found in the case of the horse manure under stirring with aeration.

  14. Toxicological studies of aqueous extract of Acacia nilotica root

    Directory of Open Access Journals (Sweden)

    Alli Lukman Adewale

    2015-03-01

    Full Text Available Acacia nilotica is a widely used plant in traditional medical practice in Northern Nigeria and many African countries. The aim of this study was to determine the toxicological effects of a single dose (acute and of repeated doses (sub-acute administration of aqueous extract of A. nilotica root in rodents, following our earlier study on antiplasmodial activity. In the acute toxicity test, three groups of Swiss albino mice were orally administered aqueous extract of A. nilotica (50, 300 and 2000 mg/kg body weight and signs of toxicity were observed daily for 14 days. In the sub-acute toxicity study, four groups of 12 rats (6 male and 6 female were used. Group 1 received 10 ml/kg b.w distilled water (control, while groups 2, 3 and 4 received 125, 250 and 500 mg/kg b.w of the extract, respectively, for 28 consecutive days by oral gavage. Signs of toxicity/mortality, food and water intake and body weight changes were observed. Biochemical parameters were analysed in both plasma and liver homogenate. In the acute and sub-acute toxicity studies, the extract did not cause mortality. A significant reduction in the activity of lactate dehydrogenase was observed at 250 and 500 mg/kg b.w, while alanine aminotransferase, aspartate aminotransferase and alkaline phosphatase activities were significantly higher than control values at 500 mg/kg b.w. The aqueous extract of A. nilotica was found to be safe in single dose administration in mice but repeated administration of doses higher than 250 mg/kg b.w of the extract for 28 days in rats may cause hepatotoxicity.

  15. Aqueous extract of neem leaves in treatment of Psoriasis vulgaris

    Directory of Open Access Journals (Sweden)

    Pandey S

    1994-01-01

    Full Text Available A double blind clinical drug trial was conducted to see the efficacy of an indigenous drug made up of aqueous extract of Neem leaves in 50 cases of uncomplicated psoriasis taking conventional coal tar regime. Patients taking drug in addition to coal tar had shown a quicker and better response in comparison to placebo group. No any untoward effect was noticed during the period of trial. Probable mode of action is discussed.

  16. Phenolic compounds from the aqueous extract of Acacia catechu

    Institute of Scientific and Technical Information of China (English)

    Xing Cui Li; Li Xin Yang; Hong Qing Wang; Ruo Yun Chen

    2011-01-01

    From the aqueous extract of Acacia catechu, two new phenolic compounds (3R,4R)-3-(3,4-dihydroxyphenyl)-4-hydroxycy-clohexanone (1) and (4R)-5-(l-(3,4-dihydrophenyl)-3-oxoburyl)-dihydrofuran-2(3H)-one (2) were obtained. Their structures were determined on the basis of spectroscopic analysis. Free-radical scavenging activities of them were evaluated.

  17. Growth inhibition of struvite crystals by the aqueous root extract of Rotula aquatica.

    Science.gov (United States)

    Chauhan, C K; Joshi, M J; Vaidya, A D B

    2011-06-01

    Formation of urinary stone is a serious and debilitating problem throughout the world. In the present study, the inhibitory effect of aqueous extract of root of Rotula aquatica was investigated against struvite crystals (one of the components of urinary stone) grown in vitro using single diffusion gel growth technique. For setting the gel, sodium metasilicate solution (specific gravity 1.05) and 0.5 M aqueous solution of ammonium dihydrogen phosphate were mixed, so that the pH of the mixture could be set at 7.0. Equal amounts of supernatant solution of magnesium acetate (1.0 M) prepared with 0.0%, 0.5% and 1% concentrations of the extract were gently poured on the set gels. It was observed that the number, dimension, total mass, total volume, growth rate and depth of growth of struvite crystals decreased with the increasing extract concentrations in the supernatant solutions. The enhancement of dissolution rate and fragmentation of struvite crystals suggested potential application of the extract for inhibition of struvite type urinary stone.

  18. Evaluation of the Hypoglycemic Properties of Anacardium humile Aqueous Extract

    Directory of Open Access Journals (Sweden)

    Márcio A. Urzêda

    2013-01-01

    Full Text Available The antihyperglycemic effects of several plant extracts and herbal formulations which are used as antidiabetic formulations have been described and confirmed to date. The main objective of this work was to evaluate the hypoglycemic activity of the aqueous extract of Anacardium humile. Although the treatment of diabetic animals with A. humile did not alter body weight significantly, a reduction of the other evaluated parameters was observed. Animals treated with A. humile did not show variation of insulin levels, possibly triggered by a mechanism of blood glucose reduction. Levels of ALT (alanine aminotransferase decreased in treated animals, suggesting a protective effect on liver. Levels of cholesterol were also reduced, indicating the efficacy of the extract in reestablishing the balance of nutrients. Moreover, a kidney protection may have been achieved due to the partial reestablishment of blood glucose homeostasis, while no nephrotoxicity could be detected for A. humile. The obtained results demonstrate the effectiveness of A. humile extracts in the treatment of alloxan-induced diabetic rats. Therefore, A. humile aqueous extract, popularly known and used by diabetic patients, induced an improvement in the biochemical parameters evaluated during and following treatment of diabetic rats. Thus, a better characterization of the medicinal potential of this plant will be able to provide a better understanding of its mechanisms of action in these pathological processes.

  19. Antioxidative and antiplatelet effects of aqueous inflorescence Piper betle extract.

    Science.gov (United States)

    Lei, Daniel; Chan, Chiu-Po; Wang, Ying-Jan; Wang, Tong-Mei; Lin, Bor-Ru; Huang, Chun-Hsun; Lee, Jang-Jaer; Chen, Hsin-Ming; Jeng, Jiiang-Huei; Chang, Mei-Chi

    2003-03-26

    Piper betle, belonging to the Piperaceae family, is a tropical plant, and its leaf and inflorescence are popularly consumed by betel quid (BQ) chewers in Taiwan and many other South and Southeast Asian countries. However, little is known about the biochemical properties of inflorescence Piper betle (IPB) toward reactive oxygen species (ROS) and platelet functions. In the present work, aqueous IPB extract was shown to be a scavenger of H(2)O(2), superoxide radical, and hydroxyl radical with a 50% inhibitory concentration (IC(50)) of about 80, 28, and 73 microg/mL, respectively. IPB extract also prevented the hydroxyl radical induced PUC18 plasmid DNA breaks at concentrations higher than 40 microg/mL. Since ROS are crucial for platelet aggregation, we further found that IPB extract also inhibited the arachidonic acid (AA) induced and collagen-induced platelet aggregation, with an IC(50) of 207 and 335 microg/mL, respectively. IPB extract also inhibited the AA-, collagen- (>100 microg/mL of IPB), and thrombin (>250 microg/mL of IPB)-induced thromboxane B(2) (TXB(2)) production by more than 90%. However, IPB extract showed little effect on thrombin-induced aggregation. These results indicated that aqueous components of IPB are potential ROS scavengers and may prevent the platelet aggregation possibly via scavenging ROS or inhibition of TXB(2) production.

  20. Calixarene-entrapped nanoemulsion for uranium extraction from contaminated solutions.

    Science.gov (United States)

    Spagnul, Aurélie; Bouvier-Capely, Céline; Phan, Guillaume; Rebière, François; Fattal, Elias

    2010-03-01

    Accidental cutaneous contamination by actinides such as uranium occurring to nuclear power plant workers can lead to their dissemination in other tissues and induce severe damages. Until now, no specific emergency treatment for such contamination has been developed. The aim of the present work was to formulate a tricarboxylic calix[6]arene molecule, known to exhibit good affinity and selectivity for complexing uranium, within a topical delivery system for the treatment of skin contamination. Since calixarene was shown to reduce oil/water interfacial tension, we have designed an oil-in-water nanoemulsion, taking advantage of the small droplet size offering a high contact surface with the contaminated aqueous medium. Characterization of the calixarene nanoemulsion was performed by determination of the oily droplet size, zeta potential and pH, measured as a function of the calixarene concentration. The obtained results have confirmed the surface localization of calixarene molecules being potentially available to extract uranyl ions from an aqueous contaminated solution. In a preliminary experiments, the calixarene nanoemulsion was used for the removal of free uranium from an aqueous contaminated solution. Results showed that the calixarene nanoemulsion extracted up to 80 +/- 5% of uranium, which demonstrates the potential interest of this delivery system for uranium skin decontamination.

  1. Adsorption Kinetics of Methylene Blue from Aqueous Solutions onto Palygorskite

    Institute of Scientific and Technical Information of China (English)

    PENG Shuchuan; WANG Shisheng; CHEN Tianhu; JIANG Shaotong; HUANG Chuanhui

    2006-01-01

    The adsorption kinetics of methylene blue from aqueous solutions on purified palygorskite was investigated. The kinetics data related to the adsorption of methylene blue from aqueous solutions are in good agreement with the pseudo-second order equation in ranges of initial concentration of 120-210 mg/L, oscillation speed of 100-200 r/min and temperature of 298-328K. The experimental results show that methylene blue is only adsorbed onto the external surface of purified palygorskite,and the apparent adsorption activation energy is 13.92 k J/mol. The relatively low apparent adsorption activation energy suggests that the adsorption of methylene blue involves in not only a chemical, but also a physical adsorption process, and it is controlled by the combination of chemical adsorption and liquid-film diffusion.

  2. Photodegradation of Norfloxacin in aqueous solution containing algae

    Institute of Scientific and Technical Information of China (English)

    Junwei Zhang; Dafang Fu; Jilong Wu

    2012-01-01

    Photodegradation of Norfloxacin in aqueous solution containing algae under a medium pressure mercury lamp (15 W,λmax =365 nm) was investigated.Results indicated that the photodegradation of Norfloxacin could be induced by the algae in the heterogeneous algaewater systems.The photodegradation rate of Norfloxacin increased with increasing algae concentration,and was greatly influenced by the temperature and pH of solution.Meanwhile,the cooperation action of algae and Fe(Ⅲ),and the ultrasound were beneficial to photodegradation of Norfloxaciu.The degradation kinetics of Norfloxacin was found to follow the pseudo zero-order reaction in the suspension of algae.In addition,we discussed the photodegradation mechanism of Norfloxacin in the suspension of algae.This work will be helpful for understanding the photochemical degradation of antibiotics in aqueous environment in the presence of algae,for providing a new method to deal with antibiotics pollution.

  3. Predicting accurate absolute binding energies in aqueous solution

    DEFF Research Database (Denmark)

    Jensen, Jan Halborg

    2015-01-01

    Recent predictions of absolute binding free energies of host-guest complexes in aqueous solution using electronic structure theory have been encouraging for some systems, while other systems remain problematic. In this paper I summarize some of the many factors that could easily contribute 1-3 kcal...... mol(-1) errors at 298 K: three-body dispersion effects, molecular symmetry, anharmonicity, spurious imaginary frequencies, insufficient conformational sampling, wrong or changing ionization states, errors in the solvation free energy of ions, and explicit solvent (and ion) effects that are not well......-represented by continuum models. While I focus on binding free energies in aqueous solution the approach also applies (with minor adjustments) to any free energy difference such as conformational or reaction free energy differences or activation free energies in any solvent....

  4. Adsorption of cadmium from aqueous solutions by perlite.

    Science.gov (United States)

    Mathialagan, T; Viraraghavan, T

    2002-10-14

    The present study examined the use of perlite for the removal of cadmium from aqueous solutions. The effects of pH and contact time on the adsorption process were examined. The optimum pH for adsorption was found to be 6.0. Residual cadmium concentration reached equilibrium in 6h and the rate of cadmium adsorption by perlite was rapid in the first hour of the reaction time. Ho's pseudo-second-order model best described the kinetics of the reaction. Batch adsorption experiments conducted at room temperature (22+/-1 degrees C) showed that the adsorption pattern followed the Freundlich isotherm model. The maximum removal of cadmium obtained from batch studies was 55%. Thomas model was used to describe the adsorption data from column studies. The results generally showed that perlite could be considered as a potential adsorbent for cadmium removal from aqueous solutions.

  5. Removal of methyl violet from aqueous solution by perlite.

    Science.gov (United States)

    Doğan, Mehmet; Alkan, Mahir

    2003-11-01

    The use of perlite for the removal of methyl violet from aqueous solutions at different concentration, pH, and temperature has been investigated. Adsorption equilibrium is reached within 1 h. The capacity of perlite samples for the adsorption of methyl violet was found to increase with increasing pH and temperature and decrease with expansion and increasing acid-activation. The adsorption isotherms are described by means of the Langmuir and Freundlich isotherms. The adsorption isotherm was measured experimentally at different conditions and the experimental data were correlated reasonably well by the adsorption isotherm of Langmuir. The order of heat of adsorption corresponds to a physical reaction. It is concluded that the methyl violet is physically adsorbed onto the perlite. The removal efficiency (P) and dimensionless separation factor (R) have shown that perlite can be used for removal of methyl violet from aqueous solutions, but unexpanded perlite is more effective.

  6. SWELLING EQUILIBRIUM OF NONIONIC POLYACRYLAMIDE HYDROGEL IN AQUEOUS SALT SOLUTIONS

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    A series of nonionic polyacrylamide hydrogels, using acrylamide as monomer and N,N’-methylene diacrylamide as crosslinking agent, were prepared by the free radical polymerization in aqueous solution. Swelling equilibria for the gels were carried out in aqueous solutions of NaCl, KCl, CaCl2, Na2HPO4 and K2HPO4 with concentration ranging from 10-3 to 5mol/kgH2O at 25℃. Experimental results revealed that the chlorides and phosphates cause a different behavior at higher salt concentration. The swelling ratio increases with increasing concentration of chlorides salts, while decreases with the increased phosphates salt concentration. The phenomena seem to be related to the different interactions of chloride and hydrogen phosphate ions with the network groups. Furthermore, the effects of different concentration of crosslinking agent and total monomers on gel swelling performance were also investigated.

  7. A lithium ion battery using an aqueous electrolyte solution

    Science.gov (United States)

    Chang, Zheng; Li, Chunyang; Wang, Yanfang; Chen, Bingwei; Fu, Lijun; Zhu, Yusong; Zhang, Lixin; Wu, Yuping; Huang, Wei

    2016-06-01

    Energy and environmental pollution have become the two major problems in today’s society. The development of green energy storage devices with good safety, high reliability, high energy density and low cost are urgently demanded. Here we report on a lithium ion battery using an aqueous electrolyte solution. It is built up by using graphite coated with gel polymer membrane and LISICON as the negative electrode, and LiFePO4 in aqueous solution as the positive electrode. Its average discharge voltage is up to 3.1 V and energy density based on the two electrode materials is 258 Wh kg‑1. It will be a promising energy storage system with good safety and efficient cooling effects.

  8. Diketopiperazine-mediated peptide formation in aqueous solution

    Science.gov (United States)

    Nagayama, M.; Takaoka, O.; Inomata, K.; Yamagata, Y.

    1990-05-01

    Though diketopiperazines (DKP) are formed in most experiments concerning the prebiotic peptide formation, the molecules have not been paid attention in the studies of chemical evolution. We have found that triglycine, tetraglycine or pentaglycine are formed in aqueous solution of glycine anhydride (DKP) and glycine, diglycine or triglycine, respectively. A reaction of alanine with DKP resulted in the formation of glycylglycylalanine under the same conditions. These results indicate that the formation of the peptide bonds proceeds through the nucleophilic attack of an amino group of the amino acids or the oligoglycines on the DKP accompanied by the ring-opening. The formation of glycine anhydride, di-, tri- and tetraglycine was also observed in a mixed aqueous solution of urea and glycine in an open system to allow the evaporation of ammonia. A probable pathway is proposed for prebiotic peptide formation through diketopiperazine on the primitive Earth.

  9. Zinc chloride aqueous solution as a solvent for starch.

    Science.gov (United States)

    Lin, Meiying; Shang, Xiaoqin; Liu, Peng; Xie, Fengwei; Chen, Xiaodong; Sun, Yongyi; Wan, Junyan

    2016-01-20

    It is important to obtain starch-based homogeneous systems for starch modification. Regarding this, an important key point is to find cheap, low-cost and low-toxicity solvents to allow complete dissolution of starch and its easy regeneration. This study reveals that a ZnCl2 aqueous solution is a good non-derivatizing solvent for starch at 50 °C, and can completely dissolve starch granules. The possible formation of a "zinc-starch complex" might account for the dissolution; and the degradation of starch, which was caused by the H(+) inZnCl2 aqueous solution, could not contribute to full dissolution. From polarized light microscopic observation combined with the solution turbidity results, it was found that the lowest ZnCl2 concentration for full dissolution was 29.6 wt.% at 50 °C, with the dissolving time being 4h. Using Fourier-transform infrared (FTIR), solid state (13)C nuclear magnetic resonance (NMR), and X-ray diffraction (XRD), it was revealed that ZnCl2 solution had no chemical reaction with starch glucosides, but only weakened starch hydrogen bonding and converted the crystalline regions to amorphous regions. In addition, as shown by intrinsic viscosity and thermogravimetric analysis (TGA), ZnCl2 solution caused degradation of starch macromolecules, which was more serious with a higher concentration of ZnCl2 solution.

  10. Fractional Walden rule for electrolytes in supercooled disaccharide aqueous solutions.

    Science.gov (United States)

    Longinotti, M Paula; Corti, Horacio R

    2009-04-23

    The electrical conductivity of CsCl, KCl, Bu(4)NBr, and Bu(4)NI was studied in stable and supercooled (metastable) sucrose and trehalose aqueous solutions over a wide viscosity range. The results indicate that large positive deviations from the Walden rule occur in these systems due to the higher tendency of the ions to move in water-rich regions, as previously observed for NaCl and MgCl(2). The electrical molar conductivity viscosity dependence can be described with a fractional Walden rule (Lambdaeta(alpha) = constant), where alpha is a decoupling parameter which increases with ionic size and varies between 0.61 and 0.74 for all of the studied electrolytes. Using the electrical molar conductivity dependence of ion-ion interactions, an effective dielectric constant was calculated for a trehalose 39 wt% aqueous solution as a function of temperature. Above 278 K, the effective and the bulk solution dielectric constants are similar, but at lower temperatures, where the carbohydrate becomes less mobile than water, the effective dielectric constant approaches the dielectric constant of water. We also conclude that the solute-solvent dielectric friction contribution can be neglected, reinforcing the idea that the observed breakdown of the Walden rule is due to the existence of local microheterogeneities. The Walden plots for the studied ionic solutes show a decoupling similar to that found for the diffusion of water in the same solutions.

  11. Possibility of cerium extraction from solutions by inorganic redoxite

    Energy Technology Data Exchange (ETDEWEB)

    Vol' khin, V.V.; L' vovich, B.I.; Kalyuzhnyj, A.V. (Permskij Politekhnicheskij Inst. (USSR))

    1981-01-01

    Ce(3) extraction process from aqueous solutions (0.01 n solution of Ce/sub 2/(SO/sub 4/)/sub 3/) by NiOOH hydroxide, used as an inorganic redox-sorbent (redoxite), is studied. Porocess has been carried out under static and dynamic conditions at 295+-2 K. During the interaction of Ce(3) ions with NiOOH redox potential of the (PHI) system changes insignificantly. The PHI value is determined mainly by redox potential of the NiOOH Ni/sup 2 +/ pair and depends on pH and Ni/sup 2 +/ ions activity in solution. Experimental results testify to considerable complete transition of Ce(3) ions from solution into solid phase. After the interaction completing PHI jump is observed and redox potential of the system is determined by the CeO(OH)/sub 2//Ce/sup 3 +/ pair.

  12. Pulse Radiolysis of Adrenaline in Acid Aqueous Solutions

    DEFF Research Database (Denmark)

    Gohn, M.; Getoff, N.; Bjergbakke, Erling

    1976-01-01

    Pulse radiolysis of adrenaline in acid aqueous solutions (pH 1–3) was carried out. The rate constants for the reactions of adrenaline with H and OH were determined: k(H + adr.) = (0·9±0·1) × 109 dm3 mol−1s−1; k(OH + adr.) = (1·65±0·15) × 1010 dm3 mol−1s−1. The H-adduct of adrenaline has two λmax...

  13. EXAFS studies of actinide ions in aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Karim, D P; Georgopoulos, P; Knapp, G S

    1979-01-01

    The applicability of the EXAFS technique in the study of actinide systems is discussed. Uranium L/sub III/-edge spectra obtained on an in-lab rotating anode EXAFS facility are presented and analyzed for crystalline UO/sub 2/F/sub 2/ and aqueous solutions containing hexavalent uranium ions. Methods for the extension of the technique to more dilute systems are discussed.

  14. Degradation of α-Naphthol by Plasma in Aqueous Solution

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Degradation of α-naphthol induced by plasma in aqueous solution was investigatedin different initial concentration with contact glow discharge electrolysis(CGDE). The resultsshowed that the degradation of α-naphthol obeyed the first-rate law. Some of predominant products were analyzed by a high performance liquid chromatography (HPLC). A path of α-naphtholdisappearance caused by plasma was proposed according to the detected intermediate products.

  15. Plasma Induced Degradation of Benzidine in Aqueous Solution

    Institute of Scientific and Technical Information of China (English)

    高锦章; 盖克; 杨武; 董彦杰

    2003-01-01

    The degradation of benzidine in aqueous solution by the low temperature plasmawas examined. The results showed that the concentration of medium and the value of pH have anappreciable effect on the degradation of benzidine. What is more important is that iron ions actingas a catalyst play an important role in this reaction. For exploring the degradation mechanismof benzidine, some of the intermediate products were recorded by HPLC(high performance liquidchromatography).

  16. Angular correlation of annihilation photons in frozen aqueous solutions

    DEFF Research Database (Denmark)

    Milosevic-Kvajic, M.; Mogensen, O. E.; Kvajic, G.

    1972-01-01

    Linear‐slit angular correlation curves were obtained at about −140°C for frozen aqueous solutions of HF, HCl, HBr, HI, NH3, FeCl2, FeCl3, NaI, H2SO4, NHO3, MnSO4, KMnO4, K2Cr2O7, NaOH, and LiOH. We found no appreciable influence of a 4% concentration of the last seven impurities. Only halide‐cont...

  17. Micellization of Zonyl FSN-100 Fluorosurfactant in Aqueous Solutions

    OpenAIRE

    Skvarla, Juraj; Uchman, M.; Procházka, K.; Tošner, Z.; Garamus, V. M.; Pispas, S.; Štěpánek, M.

    2014-01-01

    We report on micellization of nonionic fluorosurfactant Zonyl FSN-100 in aqueous solutions studied by means of NMR spectroscopy, light and small-angle X-ray scattering, surface tension measurements, isothermal titration calorimetry and fluorescence spectroscopy. The results allow for determination of basic parameters of Zonyl FSN-100 association like critical micellar concentration, size and association number of Zonyl FSN-100 micelles which have a core–shell structure with the core of fluoro...

  18. Removal of arsenic from aqueous solution using electrocoagulation.

    Science.gov (United States)

    Balasubramanian, N; Kojima, Toshinori; Basha, C Ahmed; Srinivasakannan, C

    2009-08-15

    Removal of arsenic from aqueous solution was carried out using electrocoagulation. Experiments were conducted using mild steel sacrificial anode covering wide range in operating conditions to assess the removal efficiency. The maximum arsenic removal efficiency was recorded as 94% under optimum condition. The electrocoagulation mechanism of arsenic removal has been developed to understand the effect of applied charge and electrolyte pH on arsenic removal efficiency. Further the experimental data were tested with different adsorption isotherm model to describe the electrocoagulation process.

  19. Adsorption of Copper from Aqueous Solution Using Mango Seed Powder

    OpenAIRE

    Samiksha V. Ashtikar; Amruta D. Parkhi

    2014-01-01

    The objective of the study was the removal of copper metal ions from aqueous solution using mango seed powder as low cost adsorbent. The influences of contact time, adsorbent doses & temperature were studied in batch experiments at room temperature. The results showed that with increase in the contact time percent removal of copper increases. The adsorption was rapid during first 45 minutes & equilibrium was reached in 90 minutes. The results also showed that with increase in ...

  20. The green synthesis of fine particles of gold using an aqueous extract of Monotheca buxifolia (Flac.)

    Science.gov (United States)

    Anwar, Natasha; Khan, Abbas; Shah, Mohib; Azam, Andaleeb; Zaman, Khair; Parven, Zahida

    2016-12-01

    This study deals with the synthesis and physicochemical investigation of gold nanoparticles using an aqueous extract of Monotheca buxifolia (Flac.). On the treatment of aqueous solution of tetrachloroauric acid with the plant extract, gold nanoparticles were rapidly fabricated. The synthesized particles were characterized by UV-Vis spectrophotometry (UV), Fourier transform infrared spectroscopy (FTIR), energy dispersive X-ray (EDX) and Scanning electron microscopy (SEM). The formation of AuNPs was confirmed by noting the change in color through visual observations as well as via UV-Vis spectroscopy. UV‒Vis spectrum of the aqueous medium containing gold nanoparticles showed an absorption peak at around 540 nm. FTIR was used to identify the chemical composition of gold nanoparticles and Au-capped plant extract. The presence of elemental gold was also confirmed through EDX analysis. SEM analysis of the gold nanoparticles showed that they have a uniform spherical shape with an average size in the range of 70-78 nm. This green system showed to be better capping and stabilizing agent for the fine particles. Further, the antioxidant activity of Monotheca buxifolia (Flac.) extract and Au-capped with the plant extract was also evaluated using FeCl3/K3[Fe(CN)]6 in vitro assay.

  1. Aqueous solubility data for pressurized hot water extraction for solid heterocyclic analogs of anthracene, phenanthrene and fluorene.

    Science.gov (United States)

    Karásek, Pavel; Planeta, Josef; Roth, Michal

    2007-01-26

    We report the aqueous solubilities of phenanthrene and several solid three-ring aromatic heterocycles (phenanthridine, acridine, phenazine, thianthrene, phenothiazine, phenoxathiin, phenoxazine, carbazole, dibenzofuran, dibenzothiophene, and 4,6-dimethyldibenzothiophene) at temperatures ranging from 313K to the solute melting point and at a pressure of 5MPa. The data were measured by dynamic saturation method using an in-house-assembled apparatus for pressurized hot water extraction (PHWE). The solute from a known mass of the saturated aqueous solution was transferred to an organic solvent (hexane or toluene), and the organic phase was analyzed by GC/MS. In any of the solutes, the GC/MS records did not indicate any noticeable decomposition within the temperature range of the measurements. The resultant solubilities were converted to activity coefficients of the individual solutes in saturated aqueous solutions, and the results are discussed in terms of temperature and type/number of heteroatoms.

  2. Removal of fluoride ions from aqueous solution by waste mud

    Energy Technology Data Exchange (ETDEWEB)

    Kemer, Baris; Ozdes, Duygu; Gundogdu, Ali; Bulut, Volkan N.; Duran, Celal [Karadeniz Technical University, Faculty of Arts and Sciences, Department of Chemistry, 61080 Trabzon (Turkey); Soylak, Mustafa, E-mail: soylak@erciyes.edu.tr [Erciyes University, Faculty of Arts and Sciences, Department of Chemistry, 38039 Kayseri (Turkey)

    2009-09-15

    The present study was carried out to assess the ability of original waste mud (o-WM) and different types of activated waste mud which are acid-activated (a-WM) and precipitated waste mud (p-WM), in order to remove excess of fluoride from aqueous solution by using batch technique. The p-WM exhibited greater performance than the others. Adsorption studies were conducted as a function of pH, contact time, initial fluoride concentration, adsorbent concentration, temperature, etc. Studies were also performed to understand the effect of some co-existing ions present in aqueous solutions. Adsorption process was found to be almost independent of pH for all types of waste mud. Among the kinetic models tested for p-WM, pseudo-second-order model fitted the kinetic data well with a perfect correlation coefficient value of 1.00. It was found that the adequate time for the adsorption equilibrium of fluoride was only 1 h. Thermodynamic parameters including the Gibbs free energy ({Delta}G{sup o}), enthalpy ({Delta}H{sup o}), and entropy ({Delta}S{sup o}) revealed that adsorption of fluoride ions on the p-WM was feasible, spontaneous and endothermic in the temperature range of 0-40 deg. C. Experimental data showed a good fit with the Langmuir and Freundlich adsorption isotherm models. Results of this study demonstrated the effectiveness and feasibility of WM for removal of fluoride ions from aqueous solution.

  3. Dermal absorption of a dilute aqueous solution of malathion

    Directory of Open Access Journals (Sweden)

    Scharf John

    2008-01-01

    Full Text Available Malathion is an organophosphate pesticide commonly used on field crops, fruit trees, livestock, agriculture, and for mosquito and medfly control. Aerial applications can result in solubilized malathion in swimming pools and other recreational waters that may come into contact with human skin. To evaluate the human skin absorption of malathion for the assessment of risk associated with human exposures to aqueous solutions, human volunteers were selected and exposed to aqueous solutions of malathion. Participants submerged their arms and hands in twenty liters of dilute malathion solution in either a stagnant or stirred state. The "disappearance method" was applied by measuring malathion concentrations in the water before and after human exposure for various periods of time. No measurable skin absorption was detected in 42% of the participants; the remaining 58% of participants measured minimal absorbed doses of malathion. Analyzing these results through the Hazard Index model for recreational swimmer and bather exposure levels typically measured in contaminated swimming pools and surface waters after bait application indicated that these exposures are an order of magnitude less than a minimal dose known to result in a measurable change in acetylcholinesterase activity. It is concluded that exposure to aqueous malathion in recreational waters following aerial bait applications is not appreciably absorbed, does not result in an effective dose, and therefore is not a public health hazard.

  4. Catalytic oxidation of calcium sulfite in solution/aqueous slurry

    Institute of Scientific and Technical Information of China (English)

    WU Xiao-qin; WU Zhong-biao; WANG Da-hui

    2004-01-01

    Forced oxidation of calcium sulfite aqueous slurry is a key step for the calcium-based flue gas desulfurization(FGD) residue. Experiments were conducted in a semi-batch system and a continuous flow system on lab scales. The main reactor in semi-batch system is a 1000 ml volume flask. It has five necks for continuous feeding of gas and a batch of calcium sulfite solution/aqueous slurry. In continuous flow system, the main part is a jacketed Pyrex glass reactor in which gas and solution/aqueous slurry are fed continuously. Calcium sulfite oxidation is a series of complex free-radical reactions. According to experimental results and literature data, the reactions are influenced significantly by manganese as catalyst. At low concentration of manganese and calcium sulfite, the reaction rate is dependent on 1.5 order of sulfite concentration, 0.5 order of manganese concentration, and zero order of oxygen concentration in which the oxidation is controlled by chemical kinetics. With concentrations of calcium sulfite and manganese increasing, the reactions are independent gradually on the constituents in solution but are impacted by oxygen concentration. Manganese can accelerate the free-radical reactions, and then enhances the mass transfer of oxygen from gas to liquid. The critical concentration of calcium sulfite is 0.007 mol/L, manganese is 10-4 mol/L, and oxygen is of 0.2-0.4 atm.

  5. Direct photolysis of nitroaromatic compounds in aqueous solutions

    Institute of Scientific and Technical Information of China (English)

    CHEN Bing; YANG Chun; GOH Ngoh Khang

    2005-01-01

    The direct photolysis of nitrobenzene and nitrophenols in aqueous solutions irradiated by polychromatic light were investigated.Several aromatic intermediates were identified as three nitrophenol isomers, nitrohydroquinone, nitrosobenzene, nitrocatechol, catechol and phenol. Nitrite and nitrate ions were also detected in the irradiated solution indicating direct photolysis of nitrobenzene or nitrophenols.The degradation of nitrobenzene and nitrophenols and the formation of three nitrophenol isomers were observed to follow zero-order kinetics. The quantum yields for nitrobenzene and nitrophenols removal are about 10-3 and 10-3-10-4 respectively. The mechanism for nitrobenzene degradation was suggested to follow mainly nitro-nitrite intramolecular arrangement.

  6. Analysis and modeling of alkali halide aqueous solutions

    DEFF Research Database (Denmark)

    Kim, Sun Hyung; Anantpinijwatna, Amata; Kang, Jeong Won;

    2016-01-01

    A new model is proposed for correlation and prediction of thermodynamic properties of electrolyte solutions. In the proposed model, terms of a second virial coefficient-type and of a KT-UNIFAC model are used to account for a contribution of binary interactions between ion and ion, and water and ion...... on calculations for various electrolyte properties of alkali halide aqueous solutions such as mean ionic activity coefficients, osmotic coefficients, and salt solubilities. The model covers highly nonideal electrolyte systems such as lithium chloride, lithium bromide and lithium iodide, that is, systems...

  7. Radiolysis of berberine or palmatine in aqueous solution

    Science.gov (United States)

    Marszalek, Milena; Wolszczak, Marian

    2011-01-01

    The reactions of hydrated electron (eaq-), hydrogen atom (H rad ) (reducing species) and Cl2•-, Br2•-, N,O•H radicals (oxidizing species) with berberine or palmatine in aqueous solution have been studied by steady-state and pulse radiolysis. The spectra of transient intermediates, leading to the final products, are presented. The rate constants of the reaction of eaq- and rad OH radical with both alkaloids in the homogenous solution and in the presence of DNA are reported. It is demonstrated that the primary products of the reaction of berberine and palmatine with eaq- and radicals generated during radiolysis are unstable and undergo further reactions.

  8. Radiolytic degradation of atrazine aqueous solution containing humic substances.

    Science.gov (United States)

    Basfar, A A; Mohamed, K A; Al-Abduly, A J; Al-Shahrani, A A

    2009-03-01

    Degradation of atrazine herbicide in humic substances (HS) aqueous solutions and distilled water solutions was investigated on a laboratory scale upon gamma-irradiation from a (60)Co source. In addition, the effect of ionizing radiation on the atrazine residues removal efficiency was investigated in relation to degradation of by-products. gamma-Irradiation experiments were carried out for three targeted concentrations (i.e. 0.464, 2.318 and 4.636 microM) with doses over the range 0.1-60 kGy. The initial concentration of herbicide, scavengers and irradiation doses play a significant role in the degradation efficiency as shown by decay constants of atrazine residues. gamma-Radiolysis showed that atrazine exhibited high degradation percentages at low absorbed doses in HS aqueous solutions compared to distilled water solutions. Absorbed doses from 0.6 to 21 kGy and from 6 to 72 kGy at a dose rate of 14.52 kGyh(-1) achieved 90% degradation for atrazine with initial concentrations over the range 0.464-4.636 microM in humic and distilled water solutions, respectively. The radiolytic degradation by-products and their mass balances were qualitatively determined with good confidence using gas chromatography/quadruple mass spectrometry (GC/MS) with electron impact ionization (EI(+)) mode.

  9. Applicability of the theory of volume filling of micropores to adsorption of caprolactam from aqueous solutions with active carbons

    Energy Technology Data Exchange (ETDEWEB)

    Khodorov, E.I.; Kazakov, V.A.; Semerikova, V.V.; Surinova, S.I.

    1985-06-10

    The absence of a scientifically based method of selecting adsorbents in the extraction of organic substances from waste water and solution which would allow for their multicycle use in adsorption-desorption stages often prevents the introduction of adsorption technology into industrial practice. This paper demonstrates the possibility of calculating the adsorption equilibrium of highly soluble organic compounds with the theory of volume filling of micropores equations in consideration of the activities of the extracted component in the solution and the change in the partial affinity coefficient with the degree of filling of the adsorption volume on the example of extraction of caprolactam from aqueous solutions.

  10. Extraction studies of selected actinide ions from aqueous solutions with 4-benzoyl-2,4-dihydro-5-methyl-2-phenyl-3H-pyrazol-3-thione and tri-n-octylphosphine oxide

    Energy Technology Data Exchange (ETDEWEB)

    Hannink, N.J.; Hoffman, D.C. [Lawrence Berkeley Lab., CA (United States)]|[California Univ., Berkeley, CA (United States). Dept. of Chemistry; Smith, B.F. [Los Alamos National Lab., NM (United States)

    1991-11-01

    The first measurements of distribution coefficients (K{sub d}) for Cm(III), Bk(III), Cf(III), Es(III), and Fm(III) between aqueous perchlorate solutions and solutions of 4-benzoyl-2,4-dihydro-5-methyl-2-phenyl-3H-pyrazol-3-thione (BMPPT) and the synergist tri-n-octylphosphine oxide (TOPO) in toluene are reported. Curium-243, berkelium-250, californium-249, einsteinium-254, and fermium-253 were used in these studies. The K{sub d} for {sup 241}Am was also measured and is in agreement with previously published results. Our new results show that the K{sub d}`s decrease gradually with increasing atomic number for the actinides with a dip at Cf. In general, the K{sub d}`s for these actinides are about a factor of 5 to 10 greater than the K{sub d}`s for the homologous lanthanides at a pH of 2.9, a BMPPT concentration of 0.2 M, and a TOPO concentration of 0.04 M. The larger K{sub d}`s for the actinides are consistent with greater covalent bonding between the actinide metal ion and the sulfur bonding site in the ligand.

  11. Extraction studies of selected actinide ions from aqueous solutions with 4-benzoyl-2,4-dihydro-5-methyl-2-phenyl-3H-pyrazol-3-thione and tri-n-octylphosphine oxide

    Energy Technology Data Exchange (ETDEWEB)

    Hannink, N.J.; Hoffman, D.C. (Lawrence Berkeley Lab., CA (United States) California Univ., Berkeley, CA (United States). Dept. of Chemistry); Smith, B.F. (Los Alamos National Lab., NM (United States))

    1991-11-01

    The first measurements of distribution coefficients (K{sub d}) for Cm(III), Bk(III), Cf(III), Es(III), and Fm(III) between aqueous perchlorate solutions and solutions of 4-benzoyl-2,4-dihydro-5-methyl-2-phenyl-3H-pyrazol-3-thione (BMPPT) and the synergist tri-n-octylphosphine oxide (TOPO) in toluene are reported. Curium-243, berkelium-250, californium-249, einsteinium-254, and fermium-253 were used in these studies. The K{sub d} for {sup 241}Am was also measured and is in agreement with previously published results. Our new results show that the K{sub d}'s decrease gradually with increasing atomic number for the actinides with a dip at Cf. In general, the K{sub d}'s for these actinides are about a factor of 5 to 10 greater than the K{sub d}'s for the homologous lanthanides at a pH of 2.9, a BMPPT concentration of 0.2 M, and a TOPO concentration of 0.04 M. The larger K{sub d}'s for the actinides are consistent with greater covalent bonding between the actinide metal ion and the sulfur bonding site in the ligand.

  12. Extraction studies of selected actinide ions from aqueous solutions with 4-benzoyl-2,4-Dihydro-5-methyl-2-phenyl-3H-pyrazol-3-thione and Tri-n-octylphosphine oxide

    Energy Technology Data Exchange (ETDEWEB)

    Hannink, N.J.; Hoffman, D.C. [Lawrence Berkeley Lab., CA (United States); Smith, B.F. [Los Alamos National Lab., NM (United States)

    1992-07-01

    The first measurements of distribution coefficients (k{sub d}) for Cm(III), Bk(III), Cf(III), Es(III), and Fm(III) between aqueous perchlorate solutions and solutions of 4-benzoyl-2,4-dihydro-5-methyl-2-phenyl-3H-pyrazol-3-thione (BMPPT) and the synergist tri-n-octylphosphine oxide (TOPO) in toluene are reported. Curium-243, berkelium-250, californium-249, einsteinium-254, and fermium-253 were used in these studies. The K{sub d} for {sup 241}Am was also measured and is in agreement with previously published results. Our new results show that the K{sub d}`s decrease gradually with increasing atomic number for the actinides with a dip at Cf. In general, the K{sub d}`s for these actinides are about about a factor of 10 greater than the K{sub d}`s for the homologous lanthanides at a pH of 2.9, a BMPPT concentration of 0.2 M, and a TOPO concentration of 0.04 M. The larger K{sub d}`s for the actinides are consistent with greater covalent bonding between the actinide metal ion and the sulfur bonding site in the ligand. 9 refs., 2 figs., 1 tab.

  13. Photodegradation in Micellar Aqueous Solutions of Erythrosin Esters Derivatives.

    Science.gov (United States)

    Herculano, Leandro Silva; Lukasievicz, Gustavo Vinicius Bassi; Sehn, Elizandra; Caetano, Wilker; Pellosi, Diogo Silva; Hioka, Noboru; Astrath, Nelson Guilherme Castelli; Malacarne, Luis Carlos

    2015-07-01

    Strong light absorption and high levels of singlet oxygen production indicate erythrosin B as a viable candidate as a photosensitizer in photodynamic therapy or photodynamic inactivation of microorganisms. Under light irradiation, erythrosin B undergoes a photobleaching process that can decrease the production of singlet oxygen. In this paper, we use thermal lens spectroscopy to investigate photobleaching in micellar solutions of erythrosin ester derivatives: methyl, butyl, and decyl esters in low concentrations of non-ionic micellar aqueous solutions. Using a previously developed thermal lens model, it was possible to determine the photobleaching rate and fluorescence quantum efficiency for dye-micelle solutions. The results suggest that photobleaching is related to the intensity of the dye-micelle interaction and demonstrate that the thermal lens technique can be used as a sensitive tool for quantitative measurement of photochemical properties in very diluted solutions.

  14. Corrosion behavior of bulk metallic glasses in different aqueous solutions

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    The corrosion behavior of as-cast fully amorphous, structural relaxed amorphous and crystallized Fe65.5Cr4Mo4Ga4P12C5B5.5 bulk metallic glasses (BMGs) in NaCl, HCl and NaOH solutions was investigated by electrochemical polarization and immersion methods. X-ray photoelectron spectroscopy measurements was used to analyze the changes of the elements on the alloy surface before and after immersion in various solutions. The corrosion resistance of the Fe65.5Cr4Mo4Ga4P12C5B5.5 BMG was better than its structural relaxation/crystallization counterparts and common alloys (such as stainless steel, carbonized steel, and steel) in the selected aqueous solutions. The high corrosion resistance of this alloy in corrosive solutions leads to the formation of Fe-, Cr- and Mo-enriched protective thin surface films.

  15. Structure of concentrated aqueous solutions of scandium chloride

    Science.gov (United States)

    Smirnov, P. R.; Grechin, O. V.

    2017-03-01

    It is shown via X-ray diffraction that aqueous solutions of scandium chloride form ionic associates in a wide range of concentrations. It is established that the Sc3+ ion coordination number increases upon dilution to 8.2 at an unchanged Sc3+-OH2 distance of 0.215 nm. The second coordination sphere of the cation forms at an average distance of 0.420 nm. The number of solvent molecules in the sphere logically increases during dilution. It is concluded that the anion does not form its own sphere in highly concentrated solutions. This coordination sphere begins to form only in solutions with moderate concentrations at a distance of 0.315 nm, and it contains six water molecules in diluted solutions.

  16. On the structure of an aqueous propylene glycol solution

    Science.gov (United States)

    Rhys, Natasha H.; Gillams, Richard J.; Collins, Louise E.; Callear, Samantha K.; Lawrence, M. Jayne; McLain, Sylvia E.

    2016-12-01

    Using a combination of neutron diffraction and empirical potential structure refinement computational modelling, the interactions in a 30 mol. % aqueous solution of propylene glycol (PG), which govern both the hydration and association of this molecule in solution, have been assessed. From this work it appears that PG is readily hydrated, where the most prevalent hydration interactions were found to be through both the PG hydroxyl groups but also alkyl groups typically considered hydrophobic. Hydration interactions of PG dominate the solution over PG self-self interactions and there is no evidence of more extensive association. This hydration behavior for PG in solutions suggests that the preference of PG to be hydrated rather than to be self-associated may translate into a preference for PG to bind to lipids rather than itself, providing a potential explanation for how PG is able to enhance the apparent solubility of drug molecules in vivo.

  17. Adsorption of nicotine on different zeolite types, from aqueous solutions

    Directory of Open Access Journals (Sweden)

    Stošić Dušan K.

    2007-01-01

    Full Text Available The plant alkaloid, nicotine, is a strongly toxic heterocyclic compound: the lethal dose for an adult human being (40-60 mg is importantly lower in comparison with the other known poisons such as arsenic or strychni­ne. Cigarettes represent "the most toxic and addictive form of nicotine". Besides the negative effects of nicotine on public health produced by self-administration, recently another potentially very dangerous effect has been recognized: because of its miscibility with water, nicotine can be found in industrial wastewaters, and consequently, in groundwater. Therefore, the problem of nicotine removal from aqueous solutions has became an interesting topic. In this work, the removal of nicotine has been probed by adsorption on solid materials. Adsorption of nicotine on different zeolites (clinoptilolite, ZSM-5 and β zeolite and on activated carbon was investigated from aqueous solutions, at 298 K. The obtained results are presented as adsorption isotherms: the amount of adsorbed nicotine as a function of equilibrium concentration. These data were obtained from the residual amount of nicotine in the aqueous phase, by the use of UV spectroscopy. The highest amounts of adsorbed nicotine was found for activated carbon and p zeolite (~ mmol·g-1. The attempt to modify the adsorption properties of ZSM-5 zeolite has been also done: ZSM-5 was modified by ion-exchange with VIII group metal (Cu2+ and Fe3+. In addition, the adsorption of nicotine on ZSM-5 zeolite with different Si/Al ratios has been done. It has been noticed that ion-exchange did not improve the adsorption possibilities, while the adsorption was importantly lower in the case of higher silicon content in ZMS-5 structure. 13C NMR spectra were collected for suspensions formed of solid adsorbent and aqueous solution of nicotine; in this way, the part of nicotine molecule which is most probably connected with the adsorbent was recognized.

  18. Vasorelaxant effect of the aqueous extract of Ajuga iva in rat aorta.

    Science.gov (United States)

    El-Hilaly, Jaouad; Lyoussi, Badiaâ; Wibo, Maurice; Morel, Nicole

    2004-07-01

    The aim of the present study was to investigate the ex vivo and in vitro vascular activity of the aqueous extract of Ajuga iva (L.) Schreber (Labiatae) in normotensive Wistar rats. Chronic oral administration of the extract of Ajuga iva did not significantly affect the systolic blood pressure. In aorta isolated from Ajuga iva-treated rats, the contractile response to noradrenaline was depressed compared to the responses obtained in aorta from untreated rats but the endothelium-dependent relaxation evoked by acetylcholine was not affected. In vitro, Ajuga iva extract inhibited the contraction evoked by noradrenaline. The addition of Ajuga iva extract during the plateau phase of noradrenaline-evoked contraction produced a relaxation that was sensitive to N-nitro-L-arginine. After pre-incubation of the artery in the presence of the plant extract, vasorelaxant effect was markedly less pronounced. The endothelium-dependent relaxation induced by acetylcholine was concentration-dependently blunted in the presence of Ajuga iva extract in the bathing solution. This study indicates that the aqueous extract of Ajuga iva possesses NO-mediated and NO-independent vasorelaxing properties in vitro while only the endothelium-independent effect was observed ex vivo.

  19. The Gibbs-free-energy landscape for the solute association in nanoconfined aqueous solutions

    Institute of Scientific and Technical Information of China (English)

    赵亮; 王春雷; 方海平; 涂育松

    2015-01-01

    The theoretical model and the numerical analyses on the Gibbs-free-energy of the association states of am-phiphilic molecules in nanoconfined aqueous solutions are presented in detail. We exhibit the continuous change of the Gibbs-free-energy trend, which plays a critical role in the association states of the system transforming from the dispersion state, through the “reversible state”, and finally to the aggregation state in amphiphilic molecule solutions. Furthermore, for the“reversible state”, we present the difference in the free-energy bar-rier heights of the dispersion state and aggregation state, resulting from the competition between the entropy, which makes the solute molecules evenly disperse in the solution and the energy contribution driving the am-phiphilic molecules to aggregate into a larger cluster. These findings provide a comprehensive understanding of confinement effects on the solute association processes in aqueous solutions and may further improve the techniques of material fabrication.

  20. Separation of glycols from dilute aqueous solutions via complexation with boronic acids

    Energy Technology Data Exchange (ETDEWEB)

    Randel, L.A.; King, C.J.

    1991-07-01

    This work examines methods of separating low molecular weight glycols from dilute aqueous solution. Extraction into conventional solvents is generally not economical, since, in the literature reviewed, distribution ratios for the two- to four-carbon glycols are all less than one. Distribution ratios can be increased, however, by incorporating into the organic phase an extracting agent that will complex with the solute of interest. The extracting agent investigated in this work is 3-nitrophenylboronic acid (NPBA). NPBA, a boric acid derivative, reversibly complexes with many glycols. The literature on complexation of borate and related compounds with glycols, including mechanistic data, measurement techniques, and applications to separation processes, provides information valuable for designing experiments with NPBA and is reviewed herein. 88 refs., 15 figs., 24 tabs.

  1. Enzyme-assisted aqueous extraction of lipid from microalgae.

    Science.gov (United States)

    Liang, Kehong; Zhang, Qinghua; Cong, Wei

    2012-11-28

    An improved lipid extraction process has been established for microalgal using enzyme-assisted aqueous extraction processing (EAEP), which mainly involved in sonication and enzyme treatment. As compared to cellulase, neutral protease and alkaline protease, significantly higher lipid recovery was achieved by snailase and trypsin. The highest lipid recovery of 49.82% was obtained by a combined sonication-enzyme treatment at pH 4. The enhancement mechanism of the EAEP was analyzed in terms of the particle size of cream and zeta potential. In addition, microalgal lipid recovery was also affected by lipid class composition and the type of algae. The present study demonstrates a promising alternative to conventional lipid extraction of microalgae and the quantitative information on EAEP of oleaginous alga can provide valuable data for process design at pilot and industrial scale.

  2. Aqueous extracts of microalgae exhibit antioxidant and anticancer activities

    Institute of Scientific and Technical Information of China (English)

    Sanaa MM Shanab; Soha SM Mostafa; Emad A Shalaby; Ghada I Mahmoud

    2012-01-01

    Objective: To investigate the antioxidant and anticancer activities of aqueous extracts of nine microalgal species. Methods: Variable percentages of major secondary metabolites (total phenolic content, terpenoids and alkaloids) as well as phycobiliprotein pigments (phycocyanin, allophycocyanin and phycoerythrin) in the aqueous algal extracts were recorded. Antioxidant activity of the algal extracts was performed using 2, 2 diphenyl-1-picrylhydrazyl (DPPH) test and 2,2'-azino-bis (ethylbenzthiazoline-6-sulfonic acid (ABTS.+) radical cation assay. Anticancer efficiency of the algal water extracts was investigated against Ehrlich Ascites Carcinoma cell (EACC) and Human hepatocellular cancer cell line (HepG2). Results: Antioxidant activity of the algal extracts was performed using DPPH test and ABTS.+ radical cation assays which revealed 30.1-72.4% and 32.0-75.9% respectively. Anticancer efficiency of the algal water extracts was investigated against Ehrlich Ascites Carcinoma Cell (EACC) and Human Hepatocellular cancer cell line (HepG2) with an activity ranged 87.25% and 89.4% respectively. Culturing the promising cyanobacteria species; Nostocmuscorum and Oscillatoria sp. under nitrogen stress conditions (increasing and decreasing nitrate content of the normal BG11 medium, 1.5 g/L), increased nitrate concentration (3, 6 and 9 g/L) led to a remarkable increase in phycobilin pigments followed by an increase in both antioxidant and anticancer activities in both cyanobacterial species. While the decreased nitrate concentration (0.75, 0.37 and 0.0 g/L) induced an obvious decrease in phycobilin pigments with complete absence of allophycocyanin in case of Oscillatoria sp. Conclusions: Nitrogen starvation (0.00 g/L nitrate) induced an increase and comparable antioxidant and anticancer activities to those cultured in the highest nitrate content.

  3. Non-aqueous heavy oil extraction from oil sand

    Energy Technology Data Exchange (ETDEWEB)

    Bohnert, George [National Nuclear Security Administration (United States)

    2011-07-01

    The Kansas City plant operated by Honeywell has a long history of working with DOE NNSA on engineering and manufacturing services supporting national security requirements. The plant has developed a non-aqueous method for heavy oil extraction from oil sands. This method is environmentally friendly as it does not use any external body of water, which would normally be contaminated in the conventional method. It is a 2 phase process consisting of terpene, limonene or alpha pinene, and carbon dioxide. The CO2 and terpene phases are both closed loop systems which minimizes material loss. The limonene and alpha pinene are both naturally derived solvents that come from citrus sources or pine trees respectively. Carbon dioxide is an excellent co-solvent with terpene. There is also a possibility for heat loss recovery during the distillation phase. This process produces clean dry sand. Laboratory tests have concluded that this using non-aqueous liquids process works effectively.

  4. RHEOLOGICAL BEHAVIOR OF ERWINIA GUM IN AQUEOUS SOLUTION

    Institute of Scientific and Technical Information of China (English)

    Li-na Zhang; Mei Zhang; Jing-hua Chen; Hideki Iijima; Hiromichi Tsuchiya

    1999-01-01

    Erwinia (E) gum, an extracellular polysaccharide, is composed of fucose, galatose, glucose and glucuronic acid. Its viscosity behavior was investigated by a low-shear-rate multiball viscometer and a rotational viscometer. Its weight-average molecular weight Mw and intrinsic viscosity [η] in 0.2 mol/L NaCl aqueous solution were measured by light scattering method at 35℃ and viscometry at 25℃ and found to be 1.06 × 106 g/mol and 1050 mL/g, respectively, and its aggregates in aqueous solution were proved by gel permeation chromatography (GPC). These results indicated that E gum in water has exceedingly high viscosity and exhibits Binham fluid behavior, owing to its aggregation. The viscosity of E gum decreased with increasing temperature, and the turning point appeared at 38℃ for dilute solution and 80℃ for concentrated solution suggesting that the aggregates of E gum in water started to disaggregate under these temperatures. In addition, the aggregates can be disrupted by adding either acid or base. The experimental results indicated that the E gum is a good thickening agent, and its fluid behavior is similar to xanthan.

  5. Optimising the Encapsulation of an Aqueous Bitter Melon Extract by Spray-Drying.

    Science.gov (United States)

    Tan, Sing Pei; Kha, Tuyen Chan; Parks, Sophie; Stathopoulos, Costas; Roach, Paul D

    2015-09-09

    Our aim was to optimise the encapsulation of an aqueous bitter melon extract by spray-drying with maltodextrin (MD) and gum Arabic (GA). The response surface methodology models accurately predicted the process yield and retentions of bioactive concentrations and activity (R² > 0.87). The optimal formulation was predicted and validated as 35% (w/w) stock solution (MD:GA, 1:1) and a ratio of 1.5:1 g/g of the extract to the stock solution. The spray-dried powder had a high process yield (66.2% ± 9.4%) and high retention (>79.5% ± 8.4%) and the quality of the powder was high. Therefore, the bitter melon extract was well encapsulated into a powder using MD/GA and spray-drying.

  6. Optimising the Encapsulation of an Aqueous Bitter Melon Extract by Spray-Drying

    Directory of Open Access Journals (Sweden)

    Sing Pei Tan

    2015-09-01

    Full Text Available Our aim was to optimise the encapsulation of an aqueous bitter melon extract by spray-drying with maltodextrin (MD and gum Arabic (GA. The response surface methodology models accurately predicted the process yield and retentions of bioactive concentrations and activity (R2 > 0.87. The optimal formulation was predicted and validated as 35% (w/w stock solution (MD:GA, 1:1 and a ratio of 1.5:1 g/g of the extract to the stock solution. The spray-dried powder had a high process yield (66.2% ± 9.4% and high retention (>79.5% ± 8.4% and the quality of the powder was high. Therefore, the bitter melon extract was well encapsulated into a powder using MD/GA and spray-drying.

  7. Monte Carlo Simulation of Aqueous Dilute Solutions of Polyhydric Alcohols

    Science.gov (United States)

    Lilly, Arnys Clifton, Jr.

    In order to investigate the details of hydrogen bonding and solution molecular conformation of complex alcohols in water, isobaric-isothermal Monte Carlo simulations were carried out on several systems. The solutes investigated were ethanol, ethylene glycol, 1,2-propylene glycol, 1,3 -propylene glycol and glycerol. In addition, propane, which does not hydrogen bond but does form water hydrates, was simulated in aqueous solution. The complex alcohol-water systems are very nonideal in their behavior as a function of solute concentration down to very dilute solutions. The water model employed was TIP4P water^1 and the intermolecular potentials employed are of the Jorgensen type^2 in which the interactions between the molecules are represented by interaction sites usually located on nuclei. The interactions are represented by a sum of Coulomb and Lennard-Jones terms between all intermolecular pairs of sites. Intramolecular rotations in the solute are modeled by torsional potential energy functions taken from ethanol, 1-propanol and 2-propanol for C-O and C-C bond rotations. Quasi-component pair correlation functions were used to analyze the hydrogen bonding. Hydrogen bonds were classified as proton acceptor and proton donor bonds by analyzing the nearest neighbor pair correlation function between hydroxyl oxygen and hydrogen and between solvent-water hydrogen and oxygen. The results obtained for partial molar heats of solution are more negative than experimental values by 3.0 to 14 kcal/mol. In solution, all solutes reached a contracted molecular geometry with the OH groups generally on one side of the molecule. There is a tendency for the solute OH groups to hydrogen bond with water, with more proton acceptor bonds than proton donor bonds. The water -solute binding energies correlate with experimental measurements of the water-binding properties of the solute. ftn ^1Jorgensen, W. L. et al, J. Chem. Phys., 79, 926 (1983). ^2Jorgensen, W. L., J. Phys Chem., 87, 5304

  8. Beryllium Chelation by Dicarboxylic Acids in Aqueous Solution.

    Science.gov (United States)

    Schmidt, Michael; Bauer, Andreas; Schmidbaur, Hubert

    1997-05-07

    Maleic and phthalic acids are found to react with Be(OH)(2), generated in situ from BeSO(4)(aq) and Ba(OH)(2)(aq), in aqueous solution at pH 3.0 or 4.4, respectively (25 degrees C), to give solutions containing the complexes (H(2)O)(2)Be[(OOCCH)(2)] (1) and (H(2)O)(2)Be[(OOC)(2)C(6)H(4)] (3). The products can be isolated in high yield and identified by microanalytical data. With 2 equiv of the dicarboxylic acids and the pH adjusted to 5.5 and 5.9, respectively, by addition of ammonia, the bis-chelate complexes [(NH(4))(+)](2){[Be[(OOCCH)(2)](2)}(2)(-) (2) and [(NH(4))(+)](2){Be[(OOC)(2)C(6)H(4)](2)}(2)(-) (4) are obtained, which can also be isolated. The compounds show distinct (9)Be, (1)H, and (13)C resonances in their NMR spectra in aqueous solutions. Layering of an aqueous solution of compound 4 with acetone at ambient temperature leads to the precipitation of single crystals suitable for an X-ray structure determination. This salt (5) was found to contain the bis-chelated dianion {Be[(OOC)(2)C(6)H(4)](2)}(2)(-) with the beryllium atom in the spiro center of two seven-membered rings and an overall geometry approaching closely C(2) symmetry. These anions are associated with two crystallographically independent but structurally similar counterions [MeC(O)CH(2)CMe(2)NH(3)](+), which are the product of a condensation reaction of the ammonium cation with the acetone solvent. In the crystal the ammonium hydrogen atoms of the cations form N-H.O hydrogen bonds with the oxo functions of the dianion.

  9. Nano particles@Calix arenas via aqueous solution

    Directory of Open Access Journals (Sweden)

    Sahar Dehghani

    2016-05-01

    Full Text Available The electronic structure and magnetic properties of Al2O3, GaN and Fe3O4@ Calix (8 COOH have been studied using ONIOM and DFT methods. The studies focus on how to improve the adsorption of some nano particles solution aqueous for achieving good magnetic and functionalized potential performances. The results revealed that the Fe3O4@ Calix (8 COOH and some of its derivations exhibited better thermodynamic stability. Furthermore, the particle size and magnetic property of the GaN@ Calix (8 COOH nano particles can be controlled by the aqueous. The electrical properties such as NMR Shielding, electron densities, energy densities, potential energy densities, ELF, LOL, ellipticity of electron density, eta index and ECP for nano particles@ Calix (8COOH have been calculated.

  10. Rapid structural analysis of nanomaterials in aqueous solutions

    Science.gov (United States)

    Ryuzaki, Sou; Tsutsui, Makusu; He, Yuhui; Yokota, Kazumichi; Arima, Akihide; Morikawa, Takanori; Taniguchi, Masateru; Kawai, Tomoji

    2017-04-01

    Rapid structural analysis of nanoscale matter in a liquid environment represents innovative technologies that reveal the identities and functions of biologically important molecules. However, there is currently no method with high spatio-temporal resolution that can scan individual particles in solutions to gain structural information. Here we report the development of a nanopore platform realizing quantitative structural analysis for suspended nanomaterials in solutions with a high z-axis and xy-plane spatial resolution of 35.8 ± 1.1 and 12 nm, respectively. We used a low thickness-to-diameter aspect ratio pore architecture for achieving cross sectional areas of analyte (i.e. tomograms). Combining this with multiphysics simulation methods to translate ionic current data into tomograms, we demonstrated rapid structural analysis of single polystyrene (Pst) beads and single dumbbell-like Pst beads in aqueous solutions.

  11. Hydrogen bond breaking in aqueous solutions near the critical point

    Science.gov (United States)

    Mayanovic, Robert A.; Anderson, Alan J.; Bassett, William A.; Chou, I.-Ming

    2001-01-01

    The nature of water-anion bonding is examined using X-ray absorption fine structure spectroscopy on a 1mZnBr2/6m NaBr aqueous solution, to near critical conditions. Analyses show that upon heating the solution from 25??C to 500??C, a 63% reduction of waters occurs in the solvation shell of ZnBr42-, which is the predominant complex at all pressure-temperature conditions investigated. A similar reduction in the hydration shell of waters in the Br- aqua ion was found. Our results indicate that the water-anion and water-water bond breaking mechanisms occurring at high temperatures are essentially the same. This is consistent with the hydration waters being weakly hydrogen bonded to halide anions in electrolyte solutions. ?? 2001 Elsevier Science B.V.

  12. Separation characteristics of alcohol from aqueous solution by ultrasonic atomization.

    Science.gov (United States)

    Yasuda, Keiji; Mochida, Kyosuke; Asakura, Yoshiyuki; Koda, Shinobu

    2014-11-01

    The generation rate of ultrasonically atomized droplets and the alcohol concentration in droplets were estimated by measuring the flow rate and the alcohol concentration of vapors from a bulk solution with a fountain. The effect of the alcohol concentration in the bulk solution on the generation rate of droplets and the alcohol concentration in droplets were investigated. The ultrasonic frequency was 2.4MHz, and ethanol and methanol aqueous solutions were used as samples. The generation rate of droplets for ethanol was smaller than that for methanol at the same alcohol molar fraction in the bulk solution. For both solutions, at low alcohol concentration in the bulk solution, the alcohol concentration in droplets was lower than that in vapors and the atomized droplets were visible. On the other side, at high concentration, the concentration in droplets exceeded that in vapors and the atomized droplets became invisible. These results could be explained that the alcohol-rich clusters in the bulk solution were preferentially atomized by ultrasonic irradiation. The concentration in droplets for ethanol was higher than that for methanol at low alcohol concentration because the amount of alcohol-rich clusters was larger. When the alcohol molar fraction was greater than 0.6, the atomized droplets almost consisted of pure alcohol.

  13. Anxiolytic activity of aqueous extract of Garcinia indica in mice

    Directory of Open Access Journals (Sweden)

    Manish Patel

    2013-01-01

    Full Text Available Background: Anxiety or depressed mood is associated with low levels of serotonin in the brain. A hydroxycitric acid (HCA, constituent of Garcinia indica (GIA, increases serotonin release from isolated rat brain cortex. Aim: To evaluate the anxiolytic activity of aqueous extract of dried fruits of GIA in mice. Materials and Methods: The anxiolytic-like effects of aqueous extract of dried fruits of GIA were evaluated by using elevated plus maze (EPM, hole board and light/dark exploration models in Swiss albino mice. Control mice were treated with an equal volume of saline, and positive control mice were treated with diazepam (1 mg/kg. Results: GIA administered orally, 30 min before the test in different doses (125, 250 and 500 mg/kg of body weight, was able to increase significantly (P < 0.05 the time-spent and entries into open arms of the EPM and reduced the time-spent and entries into closed arms versus control. In the hole-board test, treatment with GIA (250 and 500 mg/kg significantly increased the number of head-dips and duration of head dipping (P < 0.05. In the light-dark paradigm test, number of transitions and the time spent in the light box increased with reduction in time spent in the dark box and immobility period significantly (P < 0.05 after treatment with GIA. However, no significant changes in locomotor activity were observed versus control. Conclusion: The results of the present study suggest that aqueous extract of dried fruits of GIA is an effective anxiolytic agent for behavioural models in mice.

  14. Effect of aqueous Glycyrrhza globra extract on menopausal symptoms

    Directory of Open Access Journals (Sweden)

    N. Moslemizadeh

    2007-01-01

    Full Text Available AbstractBackground and purpose: Most women consider menopausal symptoms as natural period in their life. Many of them experienced some problems before and after the condition. There are many side effects of hormone therapy for menopausal symptoms.In different regions with various diet regimens, menopausal symptoms are different. Glycyhrhza glabra has constituents with estrogen like activity. In this study for the first time aqueous Glycyrrhza glabra extract was evaluated for decreasing menopausal symptoms.Materials and Methods: Aqueous Glycyrrhza glabra extract prepared by maceration method. The extract was concentrated and then powdered. The powder used as 250 mg capsule and standardized by glycyrrhizha content. After matching for age, menopausal age and BMI, 29 and 24 women were allocated in case and control groups respectively. Three 250 mg capsules were prescribed per day to women in case group and women in control group received placebo. The mean number of hot flashes and degree of menopausal symptoms, KI (Kupperman Index were calculated every two weeks and classified as; without symptom, weak, medium and severs. Data were analyzed using T-test and the effects of drug on hot flash and KI were assessed in different weeks.Results: The mean age and menopausal age were 50.5 ± and 48± respectively. Results showed that the mean numbers of hot flashes, KI and FSH decreased significantly in case group but they were not significant in control group. Also estradiol hormone increased significantly in case group.Conclusion: Aqueous Glycyrrhza glabra affects hot flash and KI and is a simple and cheap drug for menopausal symptoms without any side effects.

  15. 有机硅表面活性剂对水体中多环芳烃的浊点萃取研究%Cloud Point Extraction of Polycyclic Aromatic Hydrocarbons in Aqueous Solution with Silicone Surfactants

    Institute of Scientific and Technical Information of China (English)

    姚炳佳; 杨立; 胡琼; Shigendo Akita

    2007-01-01

    Cloud point extraction (CPE) processes with two silicone suffactants, Dow Corning DC-190 and DC-193, were studied as preconcentration and treatment for the water polluted by three trace polycyclic aromatic hydrocarbons (PAHs): anthracene, phenanthrene and pyrene. For all cases, the volumes of suffactant-rich phase obtained by two silicone suffactants were very small, i.e. a lower water content in the surfactant-rich phase was obtained. For example, less than 3% of the initial solution was obtained in a 1% (by mass) surfactant solution, which was much smaller than that of TX-114 in the same surfactant concentration. And TX-114 is known as a high compact surfactant-rich phase among most nonionic surfactants, thus the comparison showed that an excellent enrichment was ensured in the analysis application by the CPE process with the silicone surfactants, and the lower water content obtained in the surfactant-rich phase is also important in the large scale water treatment. The influences of additives and phase separation methodology on the recovery of PAHs were discussed. Comparing with DC-193,DC-190 has a lower cloud point and a higher recovery (near 100%) of all the three PAHs in same surfactant concentration, which was required for application as a preconcentration process prior to HPLC system. However the DC-190 solution is hard to be phase separated only by heating, whereas DC-193 has a relative higher phase separating speed by heating, but a high cloud point (around 360K) limits its application. Due to the phase separation by heating is the only method of CPE suitable to the large scale water treatment, the mixtures of two silicone surfacrants solutions were investigated in this study. A solution containing 1% of mixed DC-190 and DC-193 (in the ratio of 90∶10) removed anthracene, phenanthrene and pyrene near 100% with a relative low cloud point and quick phase separating speed.

  16. Removal of Cholera Toxin from Aqueous Solution by Probiotic Bacteria

    Directory of Open Access Journals (Sweden)

    Jussi A. O. Meriluoto

    2012-06-01

    Full Text Available Cholera remains a serious health problem, especially in developing countries where basic hygiene standards are not met. The symptoms of cholera are caused by cholera toxin, an enterotoxin, which is produced by the bacterium Vibrio cholerae. We have recently shown that human probiotic bacteria are capable of removing cyanobacterial toxins from aqueous solutions. In the present study we investigate the ability of the human probiotic bacteria, Lactobacillus rhamnosus strain GG (ATCC 53103 and Bifidobacterium longum 46 (DSM 14583, to remove cholera toxin from solution in vitro. Lactobacillus rhamnosus strain GG and Bifidobacterium longum 46 were able to remove 68% and 59% of cholera toxin from aqueous solutions during 18 h of incubation at 37 °C, respectively. The effect was dependent on bacterial concentration and L. rhamnosus GG was more effective at lower bacterial concentrations. No significant effect on cholera toxin concentration was observed when nonviable bacteria or bacterial supernatant was used.

  17. Preparation of fluorescent polyaniline nanoparticles in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Alves, Kleber G. B. [Universidade Federal de Pernambuco, Departamento de Engenharia Mecanica (Brazil); Melo, Etelino F. de [Universidade Federal de Pernambuco, Departamento de Quimica Fundamental (Brazil); Andrade, Cesar A. S. [Universidade Federal de Pernambuco, Departamento de Bioquimica (Brazil); Melo, Celso P. de, E-mail: celso@df.ufpe.br [Universidade Federal de Pernambuco, Departamento de Fisica (Brazil)

    2013-01-15

    We report the synthesis of stable polyaniline nanoparticles (PANI{sub N}Ps) based on the chemical oxidative polymerization of aniline in aqueous solutions of surfactants. Surfactants of three different types-cationic (dodecyltrimethylammonium bromide-DTAB), anionic (sodium dodecyl sulfate-SDS), and non-ionic (Triton X-405-TX-405)-were used. The resulting PANI{sub N}Ps{sub s}urfactant samples were characterized through UV-Vis, fluorescence and Fourier transform infrared spectroscopies, and scanning electronic microscopy (SEM). We have verified that the color of the PANI{sub N}Ps{sub s}urfactant dispersions is affected by a change in the pH of the solution. The PANI-NPs{sub s}urfactant colloidal suspensions in aqueous solution present a surprising high fluorescence quantum yield value (ranging from 1.9 Multiplication-Sign 10{sup -3} to 6.9 Multiplication-Sign 10{sup -3}) that can be controlled as a function of the pH, a fact that we associate to the corresponding protonation degree of the PANI polymeric chains. We suggest that these fluorescent nanocomposites can find important technological applications in different areas such as organic light emitting devices, biosensors, and pigments for coatings.

  18. In vitro and in vivo treatments of Echinococcus granulosus with Huaier aqueous extract and albendazole liposome.

    Science.gov (United States)

    Lv, Hailong; Jiang, Yufeng; Liao, Min; Sun, Hongli; Zhang, Shijie; Peng, Xinyu

    2013-01-01

    The aim of this study was to investigate the in vitro and in vivo efficacies of chemotherapy employing albendazole liposome (L-ABZ), Huaier aqueous extract, and a Huaier aqueous extract/L-ABZ combination against Echinococcus granulosus. Protoscolices of E. granulosus were incubated in vitro with the two drugs, either separately or in combination, at the following final concentrations: 2 mg/mL Huaier aqueous extract, 10 μg/mL L-ABZ, and 2 mg/mL Huaier aqueous extract + 10 μg/mL L-ABZ. Huaier aqueous extract and L-ABZ displayed slower protoscolicidal activity when applied separately than when used in combination. The maximum protoscolicidal effect was found with the combination Huaier aqueous extract + L-ABZ. Despite the low Huaier aqueous extract + L-ABZ concentrations used, protoscolex viability dropped rapidly. In vivo studies were performed on mice injected with protoscolices of E. granulosus. Huaier aqueous extract and L-ABZ were administered three times a week for a period of 4 months by the oral route. Huaier aqueous extract in E. granulosus-infected mice was effective. Combined application of both drugs did increase the treatment efficacy. In conclusion, the outcomes obtained clearly demonstrated that in vitro and in vivo treatment with Huaier aqueous extract and L-ABZ is effective against E. granulosus.

  19. Lubrication, adsorption, and rheology of aqueous polysaccharide solutions.

    Science.gov (United States)

    Stokes, Jason R; Macakova, Lubica; Chojnicka-Paszun, Agnieszka; de Kruif, Cornelis G; de Jongh, Harmen H J

    2011-04-05

    Aqueous lubrication is currently at the forefront of tribological research due to the desire to learn and potentially mimic how nature lubricates biotribological contacts. We focus here on understanding the lubrication properties of naturally occurring polysaccharides in aqueous solution using a combination of tribology, adsorption, and rheology. The polysaccharides include pectin, xanthan gum, gellan, and locus bean gum that are all widely used in food and nonfood applications. They form rheologically complex fluids in aqueous solution that are both shear thinning and elastic, and their normal stress differences at high shear rates are found to be characteristic of semiflexible/rigid molecules. Lubrication is studied using a ball-on-disk tribometer with hydrophobic elastomer surfaces, mimicking biotribological contacts, and the friction coefficient is measured as a function of speed across the boundary, mixed, and hydrodynamic lubrication regimes. The hydrodynamic regime, where the friction coefficient increases with increasing lubricant entrainment speed, is found to depend on the viscosity of the polysaccharide solutions at shear rates of around 10(4) s(-1). The boundary regime, which occurs at the lowest entrainment speeds, depends on the adsorption of polymer to the substrate. In this regime, the friction coefficient for a rough substrate (400 nm rms roughness) is dependent on the dry mass of polymer adsorbed to the surface (obtained from surface plasmon resonance), while for a smooth substrate (10 nm rms roughness) the friction coefficient is strongly dependent on the hydrated wet mass of adsorbed polymer (obtained from quartz crystal microbalance, QCM-D). The mixed regime is dependent on both the adsorbed film properties and lubricant's viscosity at high shear rates. In addition, the entrainment speed where the friction coefficient is a minimum, which corresponds to the transition between the hydrodynamic and mixed regime, correlates linearly with the ratio

  20. NMR studies of proton exchange kinetics in aqueous formaldehyde solutions

    Science.gov (United States)

    Rivlin, Michal; Eliav, Uzi; Navon, Gil

    2014-05-01

    Aqueous solutions of formaldehyde, formalin, are commonly used for tissue fixation and preservation. Treatment with formalin is known to shorten the tissue transverse relaxation time T2. Part of this shortening is due to the effect of formalin on the water T2. In the present work we show that the shortening of water T2 is a result of proton exchange between water and the major constituent of aqueous solutions of formaldehyde, methylene glycol. We report the observation of the signal of the hydroxyl protons of methylene glycol at 2 ppm to high frequency of the water signal that can be seen at low temperatures and at pH range of 6.0 ± 1.5 and, at conditions where it cannot be observed by the single pulse experiment, it can be detected indirectly through the water signal by the chemical exchange saturation transfer (CEST) experiment. The above finding made it possible to obtain the exchange rate between the hydroxyl protons of the methylene glycol and water in aqueous formaldehyde solutions, either using the dispersion of the spin-lattice relaxation rate in the rotating frame (1/T1ρ) or, at the slow exchange regime, from the line width hydroxyl protons of methylene glycol. The exchange rate was ∼104 s-1 at pH 7.4 and 37 °C, the activation energy, 50.2 kJ/mol and its pH dependence at 1.1 °C was fitted to: k (s-1) = 520 + 6.5 × 107[H+] + 3.0 × 109[OH-].

  1. Characterization of aqueous silver nitrate solutions for leakage tests

    Directory of Open Access Journals (Sweden)

    José Ferreira Costa

    2011-06-01

    Full Text Available OBJECTIVE: To determine the pH over a period of 168 h and the ionic silver content in various concentrations and post-preparation times of aqueous silver nitrate solutions. Also, the possible effects of these factors on microleakage test in adhesive/resin restorations in primary and permanent teeth were evaluated. MATERIAL AND METHODS: A digital pHmeter was used for measuring the pH of the solutions prepared with three types of water (purified, deionized or distilled and three brands of silver nitrate salt (Merck, Synth or Cennabras at 0, 1, 2, 24, 48, 72, 96 and 168 h after preparation, and storage in transparent or dark bottles. Ionic silver was assayed according to the post-preparation times (2, 24, 48, 72, 96, 168 h and concentrations (1, 5, 25, 50% of solutions by atomic emission spectrometry. For each sample of each condition, three readings were obtained for calculating the mean value. Class V cavities were prepared with enamel margins on primary and permanent teeth and restored with the adhesive systems OptiBond FL or OptiBond SOLO Plus SE and the composite resin Filtek Z-250. After nail polish coverage, the permanent teeth were immersed in 25% or 50% AgNO3 solution and the primary teeth in 5% or 50% AgNO3 solutions for microleakage evaluation. ANOVA and the Tukey's test were used for data analyses (α=5%. RESULTS: The mean pH of the solutions ranged from neutral to alkaline (7.9±2.2 to 11.8±0.9. Mean ionic silver content differed depending on the concentration of the solution (4.75±0.5 to 293±15.3 ppm. In the microleakage test, significant difference was only observed for the adhesive system factor (p=0.000. CONCLUSIONS: Under the tested experimental conditions and based on the obtained results, it may be concluded that the aqueous AgNO3 solutions: have neutral/alkaline pH and service life of up to 168 h; the level of ionic silver is proportional to the concentration of the solution; even at 5% concentration, the solutions were

  2. Characterization of aqueous silver nitrate solutions for leakage tests

    Science.gov (United States)

    COSTA, José Ferreira; SIQUEIRA, Walter Luiz; LOGUERCIO, Alessandro Dourado; REIS, Alessandra; de OLIVEIRA, Elizabeth; ALVES, Cláudia Maria Coelho; BAUER, José Roberto de Oliveira; GRANDE, Rosa Helena Miranda

    2011-01-01

    Objectives To determine the pH over a period of 168 h and the ionic silver content in various concentrations and post-preparation times of aqueous silver nitrate solutions. Also, the possible effects of these factors on microleakage test in adhesive/resin restorations in primary and permanent teeth were evaluated. Material and Methods A digital pHmeter was used for measuring the pH of the solutions prepared with three types of water (purified, deionized or distilled) and three brands of silver nitrate salt (Merck, Synth or Cennabras) at 0, 1, 2, 24, 48, 72, 96 and 168 h after preparation, and storage in transparent or dark bottles. Ionic silver was assayed according to the post-preparation times (2, 24, 48, 72, 96, 168 h) and concentrations (1, 5, 25, 50%) of solutions by atomic emission spectrometry. For each sample of each condition, three readings were obtained for calculating the mean value. Class V cavities were prepared with enamel margins on primary and permanent teeth and restored with the adhesive systems OptiBond FL or OptiBond SOLO Plus SE and the composite resin Filtek Z-250. After nail polish coverage, the permanent teeth were immersed in 25% or 50% AgNO3 solution and the primary teeth in 5% or 50% AgNO3 solutions for microleakage evaluation. ANOVA and the Tukey's test were used for data analyses (α=5%). Results The mean pH of the solutions ranged from neutral to alkaline (7.9±2.2 to 11.8±0.9). Mean ionic silver content differed depending on the concentration of the solution (4.75±0.5 to 293±15.3 ppm). In the microleakage test, significant difference was only observed for the adhesive system factor (p=0.000). Conclusions Under the tested experimental conditions and based on the obtained results, it may be concluded that the aqueous AgNO3 solutions: have neutral/alkaline pH and service life of up to 168 h; the level of ionic silver is proportional to the concentration of the solution; even at 5% concentration, the solutions were capable of

  3. ADSORPTION OF METHYLENE BLUE FROM AQUEOUS SOLUTION ON ATTAPULGITE

    Institute of Scientific and Technical Information of China (English)

    WANG Deping; LV Pengfei; YAN Yongsheng; LIU Hui; WANG Guanjun

    2007-01-01

    Batch adsorption experiments were carried out for the removal of methylene blue (MB) from aqueous solution using attapulgite as adsorbent. The effects of various parameters such as temperature, contact time, the pH value, and attapulgite dosage on the adsorption performance were investigated. The standard curve and regression equation were established by spectrophotometry. The adsorption experimental results showed that the adsorption equilibrium data were well in accord with Langmuir adsorptive model. The optimal result was acquired under the experimental condition of attapulgite dosage 0.18g, MB concentration 50.0mg/L, pH 10, and adsorption time 20min at room temperature.

  4. Kinetics of gibbsite leaching in sodium hydroxide aqueous solution

    Directory of Open Access Journals (Sweden)

    Pavlović Ljubica J.

    2002-01-01

    Full Text Available In order to study the kinetics and mechanism of the reaction, laboratory leaching was carried out with industrially produced gibbsite γ-Al(OH3 in aqueous solutions containing an excess of sodium hydroxide. The results obtained reaction temperature, duration and base concentration varied. The basic kinetic parameters were determined from: the reaction rate constant k=8.72·107 exp (-74990/RT and the process activation energy in the range Ea=72.5-96.81 kJ/mol.

  5. Pulse radiolysis of pyridine and methylpyridines in aqueous solutions

    DEFF Research Database (Denmark)

    Solar, S.; Getoff, N.; Sehested, K.

    1993-01-01

    The radicals formed from pyridine, 3-methylpyridine, 3,5-dimethylpyridine, 2,6-dimethylpyridine and 2,4,6-trimethylpyridine by attack of H, e(aq)-, OH and O.- in aqueous solutions were investigated by pulse radiolysis in the pH-range 1-13.8. The UV-vis. absorption spectra as well as the formation...... and decay kinetics for the protonated and unprotonated forms of the methylpyridine radicals studied are presented. The pK(a)-values for the OH-adducts were determined....

  6. Hydrate-based heavy metal separation from aqueous solution

    Science.gov (United States)

    Song, Yongchen; Dong, Hongsheng; Yang, Lei; Yang, Mingjun; Li, Yanghui; Ling, Zheng; Zhao, Jiafei

    2016-02-01

    A novel hydrate-based method is proposed for separating heavy metal ions from aqueous solution. We report the first batch of experiments and removal characteristics in this paper, the effectiveness and feasibility of which are verified by Raman spectroscopy analysis and cross-experiment. 88.01-90.82% of removal efficiencies for Cr3+, Cu2+, Ni2+, and Zn2+ were obtained. Further study showed that higher R141b-effluent volume ratio contributed to higher enrichment factor and yield of dissociated water, while lower R141b-effluent volume ratio resulted in higher removal efficiency. This study provides insights into low-energy, intensive treatment of wastewater.

  7. Fluorescence of aqueous solutions of commercial humic products

    Science.gov (United States)

    Gosteva, O. Yu.; Izosimov, A. A.; Patsaeva, S. V.; Yuzhakov, V. I.; Yakimenko, O. S.

    2012-01-01

    We have studied the spectral luminescence characteristics of aqueous solutions of humic products obtained from different raw material sources, and their behavior as the excitation wavelength increases from 270 nm to 355 nm. We have identified differences in the spectral properties of industrial humic products from coalified materials, lignin-containing organic waste, and humic products from plant raw material (peat, sapropel, vermicompost). We have shown that humic products from plant raw material have spectral properties closer to those for humic substances in natural water or soil than humic products from coalified materials.

  8. Standard Electrode Potentials Involving Radicals in Aqueous Solution: Inorganic Radicals

    Energy Technology Data Exchange (ETDEWEB)

    Armstrong, David A.; Huie, Robert E.; Koppenol, Willem H.; Lymar, Sergei V.; Merenyi, Gabor; Neta, Pedatsur; Ruscic, Branko; Stanbury, David M.; Steenken, Steen; Wardman, Peter

    2015-12-01

    Recommendations are made for standard potentials involving select inorganic radicals in aqueous solution at 25 °C. These recommendations are based on a critical and thorough literature review and also by performing derivations from various literature reports. The recommended data are summarized in tables of standard potentials, Gibbs energies of formation, radical pKa’s, and hemicolligation equilibrium constants. In all cases, current best estimates of the uncertainties are provided. An extensive set of Data Sheets is appended that provide original literature references, summarize the experimental results, and describe the decisions and procedures leading to each of the recommendations

  9. Adsorption of Copper from Aqueous Solution Using Mango Seed Powder

    Directory of Open Access Journals (Sweden)

    Samiksha V. Ashtikar

    2014-04-01

    Full Text Available The objective of the study was the removal of copper metal ions from aqueous solution using mango seed powder as low cost adsorbent. The influences of contact time, adsorbent doses & temperature were studied in batch experiments at room temperature. The results showed that with increase in the contact time percent removal of copper increases. The adsorption was rapid during first 45 minutes & equilibrium was reached in 90 minutes. The results also showed that with increase in the adsorbent doses & temperature percent removal of copper increases. Thus mango seeds have the potential to be applied as alternative low-cost biosorbent in the remediation of heavy metal contamination in waste water.

  10. Thermodynamics of multisolute adsorption from dilute aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Jossens, L. (Univ. Calif. Berkeley); Fritz, W.; Myers, A.L.; Prausnitz, J.M.; Schluender, E.U.

    1978-01-01

    Equilibrium adsorption data were obtained at 20/sup 0/C on activated carbon for six ternary aqueous systems simulating organic chemical wastewaters (phenol/p-nitrophenol, p-chlorophenol/p-nitrophenol, p-nitrophenol/benzoic acid, p-chlorophenol/phenyl acetic acid, o-phenylphenol/p-nitrophenol, and 2,4-dichlorophenol/dodecyl benzol sulfonic acid). The three-parameter Toth adsorption isotherm represented well the component single-solute data adsorption. With the thermodynamic ideal-adsorbed-solution method, total adsorptions were calculated from single-solute data predicted by the Toth equation and compared with experimental data. Prediction for total adsorption was within approx. 2-10Vertical Bar3<; for adsorption of individual components, within approx. 3-20Vertical Bar3<. A new three-parameter adsorption isotherm was derived, which also represented well the single-solute data. For bi-solute systems where dissociation is negligible, calculated individual adsorptions agreed with experiment within 2Vertical Bar3<. Systematic deviations between calculation and observed results may be due to the acidities of the solutes.

  11. Determination of ferrous and ferric iron in aqueous biological solutions

    Energy Technology Data Exchange (ETDEWEB)

    Pepper, S.E. [Earth and Environmental Sciences Division, Los Alamos National Laboratory, 1400 University Drive, Carlsbad, NM 88220 (United States); Borkowski, M., E-mail: marian@lanl.gov [Earth and Environmental Sciences Division, Los Alamos National Laboratory, 1400 University Drive, Carlsbad, NM 88220 (United States); Richmann, M.K.; Reed, D.T. [Earth and Environmental Sciences Division, Los Alamos National Laboratory, 1400 University Drive, Carlsbad, NM 88220 (United States)

    2010-03-24

    A solvent extraction method was employed to determine ferrous and ferric iron in aqueous samples. Fe{sup 3+} is selectively extracted into the organic phase (n-heptane) using HDEHP (bis(2-ethylhexyl) hydrogen phosphate) and is then stripped using a strong acid. After separation, both oxidation states and the total iron content were determined directly by ICP-MS analysis. This extraction method was refined to allow determination of both iron oxidation states in the presence of strong complexing ligands, such as citrate, NTA and EDTA. The accuracy of the method was verified by crosschecking using a refinement of the ferrozine assay. Presented results demonstrate the ability of the extraction method to work in a microbiological system in the presence of strong chelating agents following the bioreduction of Fe{sup 3+} by the Shewanella alga BrY. Based on the results we report, a robust approach was defined to separately analyze Fe{sup 3+} and Fe{sup 2+} under a wide range of potential scenarios in subsurface environments where radionuclide/metal contamination may coexist with strongly complexing organic contaminants.

  12. Study on diuretic activity of saffron (stigma of Crocus sativus L. Aqueous extract in rat

    Directory of Open Access Journals (Sweden)

    Nabi Shariatifar

    2014-01-01

    Full Text Available Saffron is the most expensive spice in the world and consists of the dried stigmas of Crocus sativus L. It is used as food coloring and flavoring in food industry and traditional cooking and also in folk medicine as antispasmodic, carminative, stomachic, expectorant, aphrodisiac and cardiotonic. The present study has evaluated the diuretic activity of aqueous extract of dried saffron (stigma of Crocussativus in rat. Aqueous extracts of saffron were administered to experimental rats orally as doses of 60, 120 and 240 mg/kg body weight (BW and compared with hydrochlorothiazide (10 mg/kg B.W., intraperitoneally, a potent diuretic as positive control and normal saline solution as placebo for control group. The measured parameters for diuretic activity were total urine volume, urine electrolytes concentration such as sodium and potassium, creatinine and urea concentration. The treated rats with aqueous extract of saffron as doses of 120 and 240 mg/kg BW showed higher urine output when compared to the control group. Also, it has shown a significant dose-dependent increase in the excretion of electrolytes when compared to the control group. Our findings proved the diuretic activity of saffron which is used in traditional medicine, it can be an effective and safe strategy for related dysfunction. Also further studies are needed to identify the mechanisms of action, probably other effects and interactions with other medicines.

  13. Rapid green synthesis of silver nanoparticles by aqueous extract of seeds of Nyctanthes arbor-tristis

    Science.gov (United States)

    Basu, Shibani; Maji, Priyankar; Ganguly, Jhuma

    2016-01-01

    The present study explores that the aqueous extract of the seeds of Nyctanthes arbor-tristis (aka night jasmine) is very efficient for the synthesis of stable AgNPs from aqueous solution of AgNO3. The extract acts as both reducing (from Ag+ to Ag0) and capping agent in the aqueous phase. The constituents in extract are mainly biomolecules like carbohydrates and phenolic compounds, which are responsible for the preparation of stable AgNPs within 20 min of reaction time at 25 °C using without any severe conditions. The synthesized silver nanoparticles were characterized with UV-Visible spectroscopy, FT-IR, XRD and SEM. UV-Vis spectroscopy analysis showed peak at 420 nm, which corresponds to the surface plasmon resonance of AgNPs. XRD results showed peaks at (111), (200), (220), which confirmed the presence of AgNPs with face-centered cubic structure. The uniform spherical nature of the AgNPs and size (between 50 and 80 nm) were further confirmed by SEM analysis.

  14. Photoelectron Spectra of Aqueous Solutions from First Principles

    Energy Technology Data Exchange (ETDEWEB)

    Gaiduk, Alex P.; Govoni, Marco; Seidel, Robert; Skone, Jonathan H.; Winter, Bernd; Galli, Giulia

    2016-06-08

    We present a combined computational and experimental study of the photoelectron spectrum of a simple aqueous solution of NaCl. Measurements were conducted on microjets, and first-principles calculations were performed using hybrid functionals and many-body perturbation theory at the G0W0 level, starting with wave functions computed in ab initio molecular dynamics simulations. We show excellent agreement between theory and experiments for the positions of both the solute and solvent excitation energies on an absolute energy scale and for peak intensities. The best comparison was obtained using wave functions obtained with dielectric-dependent self-consistent and range-separated hybrid functionals. Our computational protocol opens the way to accurate, predictive calculations of the electronic properties of electrolytes, of interest to a variety of energy problems.

  15. Adsorption of thorium from aqueous solutions by perlite.

    Science.gov (United States)

    Talip, Z; Eral, M; Hiçsönmez, U

    2009-02-01

    The use of expanded perlite for the adsorption of thorium from aqueous solution by batch technique is presented. The effects of particle size, pH of the solution, initial thorium concentration, shaking time, V/m ratio and temperature were determined. It was found that the adsorption capacity increases by the increase in the pH of the suspensions. The rate of thorium adsorption on expanded perlite was observed to be fast in the first hour of the reaction time. Adsorption isotherms were expressed by Langmuir and Freundlich adsorption models and the adsorption experiments conducted at 30 +/- 1 degrees C showed that the adsorption isotherms correlated well with the Langmuir model. From the adsorption data, thermodynamic parameters such as DeltaG(o), DeltaH(o) and DeltaS(o) were calculated as a function of temperature.

  16. Radiolysis of pentachlorophenol (PCP) in aqueous solution by gamma radiation

    Institute of Scientific and Technical Information of China (English)

    XUE Jun; WANG Jianlong

    2008-01-01

    Steady-state radiolysis experiments were performed to investigate the y-irradiation treatment of pentachlorophenol (PCP) in aqueoussolution. The effect of initial concentration on the PCP degradation was also investigated. The experimental results showed that γ-irradiation was able to degrade PCP in aqueous solution successfully, and the radiolytical degradation process of PCP could be describedby the first-order kinetic model. When the initial concentration of PCP was 25 and 50 mg/L and the radiation dose was 4 and 6 kGy,respectively, the degradation efficiency was 100%. A luminescence bacterial test was used for evaluating the toxicity of the radiolyticintermediate products. Total detoxification of a 75 mg/L PCP solution could be achieved by carrying out the irradiation procedure at the dose of 15 kGy.

  17. Rheological properties of aqueous solutions of biopolymeric hyaluronan

    Science.gov (United States)

    Szwajczak, Elzbieta

    2004-09-01

    Aqueous solutions of hyaluronic acid (hyaluronan, HA) were studied. The HA compound is a natural polysaccharide, bipolymer. It plays an important role in numerous biological processes as a component of the extracellular matrix, connective tissues and, especially, human and animal synovial joints. Natural and artificial solutions of the HA have demonstrated the viscoelastic nature. These properties are shown to be related to the microstructure parameters (bulk concentration, molecular weight) and external parameters (temperature, stress, shear rate). We emphasize the role of the flow properties of polymeric systems. It is found a liquid crystalline "order" can be "induced" during the material flow. The dynamic properties, such as the elastic shear modulus and viscous shear modulus, are given. These results are discussed in relation to the postulated function of hyaluronic acid in synovial joint and with respect to possibilities o their application in medicine and pharmacology.

  18. The crystal growth of barium flouride in aqueous solution

    Science.gov (United States)

    Barone, J. P.; Svrjcek, D.; Nancollas, G. H.

    1983-06-01

    The kinetics of growth of barium flouride seed crystals were investigated in aqueous solution at 25°C using a constant composition method, in which the supersaturation and ionic strength were maintained constant by the addition of titrants consisting of barium nitrate and potassium flouride solutions. The rates of reaction, studied over a range of supersaturation (σ ≈ 0.4 to 1.0), were interpreted in terms of crystal growth models. A spiral growth mechanism best describes the data, and scanning electron microscopy indicates a three-dimensional growth. In the presence of inorganic additives such as phosphate, however, induction periods precede a morphological two-dimensional crystallization. Coulter Counter results show little crystal agglomeration.

  19. Removal of phosphate from aqueous solution with blast furnace slag.

    Science.gov (United States)

    Oguz, Ensar

    2004-10-18

    Blast furnace slag was used to remove phosphate from aqueous solutions. The influence of pH, temperature, agitation rate, and blast furnace slag dosage on phosphate removal was investigated by conducting a series of batch adsorption experiments. In addition, the yield and mechanisms of phosphate removal were explained on the basis of the results of X-ray spectroscopy, measurements of zeta potential of particles, specific surface area, and images of scanning electron microscopy (SEM) of the particles before and after adsorption. The specific surface area of the blast furnace slag was 0.4m(2)g(-1). The removal of phosphate predominantly has taken place by a precipitation mechanism and weak physical interactions between the surface of adsorbent and the metallic salts of phosphate. In this study, phosphate removal in excess of 99% was obtained, and it was concluded that blast furnace slag is an efficient adsorbent for the removal of phosphate from solution.

  20. INTERACTION OF POLYVINYLPYRROLIDONE WITH METAL CHLORIDE AQUEOUS SOLUTIONS

    Institute of Scientific and Technical Information of China (English)

    Mohammad Saleem Khan; Khaista Gul; Najeeb Ur Rehman

    2004-01-01

    Interactions of polyvinylpyrrolidone (PVP) with metal chlorides (MgCl2, CaCl2, KC1 and BaC12) have been investigated by viscometric and spectrophotometric techniques in aqueous solutions. Intrinsic viscosity [η] of (PVP) has shown a discontinuity with varying concentration of metal chlorides. The decreasing order of effectiveness of cation is K1+>Ca2+> Mg2+> Ba2+ for poly(vinylpyrrolidone) solution. Changes in the absorption spectra of the cosolutes were observed in the presence of PVP in the lower limit of the UV-visible region i.e. 200-210 nm. These changes were attributed to interaction of PVP molecules with the cosolute molecules. As the concentration of the cosolute increased, a red shift in the peaks was observed, indicating an increase in interaction between PVP and cosolutes.

  1. Removal of methylene blue from aqueous solution by graphene oxide.

    Science.gov (United States)

    Yang, Sheng-Tao; Chen, Sheng; Chang, Yanli; Cao, Aoneng; Liu, Yuanfang; Wang, Haifang

    2011-07-01

    Graphene oxide (GO) is a highly effective absorbent of methylene blue (MB) and can be used to remove MB from aqueous solution. A huge absorption capacity of 714 mg/g is observed. At initial MB concentrations lower than 250 mg/L, the removal efficiency is higher than 99% and the solution can be decolorized to nearly colorless. The removal process is fast and more efficient at lower temperatures and higher pH values. The increase of ionic strength and the presence of dissolved organic matter would further enhance the removal process when MB concentration is high. The results indicate that GO can be applied in treating industrial effluent and contaminated natural water. The implications to graphene-based environmental technologies are discussed.

  2. Radiolysis of berberine or palmatine in aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Marszalek, Milena [Institute of Applied Radiation Chemistry, Technical University of Lodz, Wroblewskiego 15, 93-590 Lodz (Poland); Wolszczak, Marian, E-mail: marianwo@mitr.p.lodz.p [Institute of Applied Radiation Chemistry, Technical University of Lodz, Wroblewskiego 15, 93-590 Lodz (Poland)

    2011-01-15

    The reactions of hydrated electron (e{sub aq}{sup -}), hydrogen atom (H{sup {center_dot}}) (reducing species) and Cl{sub 2}{sup {center_dot}}{sup -},Br{sub 2}{sup {center_dot}}{sup -},{sup {center_dot}}N{sub 3},{sup {center_dot}}OH radicals (oxidizing species) with berberine or palmatine in aqueous solution have been studied by steady-state and pulse radiolysis. The spectra of transient intermediates, leading to the final products, are presented. The rate constants of the reaction of e{sub aq}{sup -} and {sup {center_dot}}OH radical with both alkaloids in the homogenous solution and in the presence of DNA are reported. It is demonstrated that the primary products of the reaction of berberine and palmatine with e{sub aq}{sup -} and radicals generated during radiolysis are unstable and undergo further reactions.

  3. Influence of coal properties on mercury uptake from aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Lakatos, J.; Brown, S.D.; Snape, C.E. [Miskolc University, Miskolc-Egyetemvaros (Hungary). Research Inst. of Applied Chemistry

    1999-10-01

    The uptake of mercury (II) from aqueous solution by a range of coals has been studied and the results have been compared to those for a number of other sorbents, including commercial active carbons and cation-exchange resins. At pH 5 in a buffer medium, the capacities for mercury removal of the low-rank coals and the oxidized bituminous coals investigated are comparable to those of the other sorbents tested. For the lignites investigated, a high content of organic sulfur does not markedly affect the capacity for mercury uptake in relatively neutral and low chloride media, owing to redox reactions being the most likely mechanism involved. However, in highly acidic solutions, the capacities for mercury uptake are considerably greater for the high-sulfur coals investigated than for their low-sulfur counterparts due to chelation being the major sorption process involved. 36 refs., 4 figs., 7 tabs.

  4. Aqueous Solution Thermal Conductivity of Beryllium-Subgroup Metal Chlorides

    Directory of Open Access Journals (Sweden)

    K. Abdullayev

    2013-01-01

    Full Text Available The paper presents experimental data on thermal conductivity of BeCl2 and SrCl2 salt aqueous solutions in the temperature range from 20 to 300 °С  and at various electrolyte concentrations  in mass percent. For the first time thermal conductivity of the system Н2О + BeCl2 has been investigated at high temperatures.The experimental results are described with the help of an empirical equation in the form of: λs = λo (1+ Am + Bm3/2 + Cm2,where λs  and λo – thermal conductivity coefficients of solution and water; A, B and C – coefficients depending on electrolyte nature; m – molality in units mol/kg.The formula error is less than  ±1 %.

  5. Modeling of sodium acetate recovery from aqueous solutions by electrodialysis.

    Science.gov (United States)

    Fidaleo, Marcello; Moresi, Mauro

    2005-09-05

    The main engineering parameters (i.e., ion transport numbers in solution and electro-membranes; effective solute and water transport numbers; effective membrane surface area, membrane surface resistances, and limiting current intensity) affecting the recovery of sodium acetate from model solutions by electrodialysis (ED) were determined in accordance with a sequential experimental procedure. Such parameters allowed a satisfactory simulation of a few validation tests carried out under constant or step-wisely variable current intensity. The performance of this ED process was characterized in terms of a current efficiency (omega) of about 93% in the constant-current region, a water transport number (t(W)) of about 15, and a specific energy consumption (epsilon) increasing from 0.14 to 0.31 kWh/kg for a solute recovery yield of 95% as the current density (j) was increased from 112 to 337 A/m2. The specific resistance of the anion- or cation-exchange membranes were found to be three or two times greater than those measured in aqueous NaCl solutions and are to be used to design and/or optimize ED stacks involved in the downstream processing of acetic acid fermentation broths.

  6. Methanol Uptake By Low Temperature Aqueous Sulfuric Acid Solutions

    Science.gov (United States)

    Iraci, Laura T.; Essin, Andrew M.; Golden, David M.; Hipskind, R. Stephen (Technical Monitor)

    2001-01-01

    To evaluate the role of upper tropospheric and lower stratospheric aerosols in the global budget of methanol, the solubility and reactivity of CH3OH in aqueous sulfuric acid solutions are under investigation. Using standard uptake techniques in a Knudsen cell reactor, we have measured the effective Henry's law coefficient, H(*), for methanol dissolution into 45 to 70 percent by weight H2SO4. We find that methanol solubility ranges from 10(exp 5) to 10(exp 8) M/atm and increases with decreasing temperature and with increasing sulfuric acid content. These solubility measurements include uptake due to physical solvation and all rapid equilibria which are established in solution. Our data indicate that simple uptake by aqueous sulfuric acid particles will not be a significant sink for methanol in the UT/LS. These results differ from those recently reported in the literature, and an explanation of this disparity will be presented. In addition to solvation, reaction between primary alcohols and sulfuric acid does occur, leading to the production of alkyl sulfates. Literature values for the rate of this reaction suggest that formation of CH3OSO3H may proceed in the atmosphere but is not significant under our experimental conditions. Results obtained using a complementary equilibrium measurement technique confirm this directly. In addition, the extent of methanol sequestration via formation of mono- and dimethylsulfate will be evaluated under several atmospheric conditions.

  7. Removal of heavy metals from aqueous solution by sawdust adsorption

    Institute of Scientific and Technical Information of China (English)

    BULUT Yasemin; TEZ Zeki

    2007-01-01

    The adsorption of lead, cadmium and nicel from aqueous solution by sawdust of walnut was investigated. The effect of contact time,initial metal ion concentration and temperature on metal ions removal has been studied. The equilibrium time was found to be of the order of 60 min. Kinetics fit pseudo first-order, second-order and intraparticle diffusion models, hence adsorption rate constants were calculated. The adsorption data of metal ions at temperatures of 25, 45 and 60C have been described by the Freundlich and Langmuir isotherm models. The thermodynamic parameters such as energy, entropy and enthalpy changes for the adsorption of heavy metal ions have also been computed and discussed. Ion exchange is probably one of the major adsorption mechanisms for binding divalent metal ions to the walnut sawdust. The selectivity order of the adsorbent is Pb(Ⅱ)≈Cd(Ⅱ)>Ni(Ⅱ). From these results, it can be concluded that the sawdust of walnut could be a good adsorbent for the metal ions from aqueous solutions.

  8. New terahertz dielectric spectroscopy for the study of aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    George, Deepu K.; Charkhesht, Ali; Vinh, N. Q., E-mail: Vinh@vt.edu [Department of Physics, Virginia Tech, Blacksburg, Virginia 24061 (United States)

    2015-12-15

    We present the development of a high precision, tunable far-infrared (terahertz) frequency-domain dielectric spectrometer for studying the dynamics of biomolecules in aqueous solutions in the gigahertz-to-terahertz frequency. As an important benchmark system, we report on the measurements of the absorption and refractive index for liquid water in the frequency range from 5 GHz to 1.12 THz (0.17–37.36 cm{sup −1} or 0.268–60 mm). The system provides a coherent radiation source with power up to 20 mW in the gigahertz-to-terahertz region. The dynamic range of our instrument reaches 10{sup 12} and the system achieves a spectral resolution of less than 100 Hz. The temperature of samples can be controlled precisely with error bars of ±0.02 °C from 0 °C to 90 °C. Given these attributes, our spectrometer provides unique capabilities for the accurate measurement of even very strongly absorbing materials such as aqueous solutions.

  9. Gamma radiolytic degradation of naphthalene in aqueous solution

    Science.gov (United States)

    Chu, Libing; Yu, Shaoqing; Wang, Jianlong

    2016-06-01

    The decomposition of naphthalene in aqueous solution was studied using gamma irradiation combined with both H2O2 and TiO2 nanoparticles. Gamma irradiation led to a complete degradation of naphthalene and a partial mineralization. With initial concentration of 5-32 mg/L, more than 98% of naphthalene was removed and TOC reduction reached 28-31% at an absorbed dose of 3.0 kGy. The degradation of naphthalene was faster at neutral pH and the initial degradation rate increased with increasing the initial concentration of naphthalene. Addition of H2O2 and TiO2 nanoparticles all enhanced the degradation and mineralization of naphthalene. TOC removal efficiency increased from 28% (irradiation alone) to 35% with addition of H2O2 (40 mg/L), and to 48% with addition of TiO2 (0.8 g/L). The degradation of naphthalene in aqueous solution by gamma irradiation was mainly through the oxidation by ·OH radicals. The intermediate naphthol and carboxylic acids such as formic acid and oxalic acid were identified by LC-MS and IC.

  10. QENS study on thermal gelation in aqueous solution of methylcellulose

    Energy Technology Data Exchange (ETDEWEB)

    Onoda-Yamamuro, N. [Department of Natural Sciences, College of Science and Engineering, Tokyo Denki University, Hiki-gun, Saitama 350-0394 (Japan)]. E-mail: yamamuro@u.dendai.ac.jp; Yamamuro, O. [Neutron Science Laboratory, Institute for Solid State Physics, University of Tokyo, 106-1 Shirakata, Tokai, Ibaraki 319-1106 (Japan); Inamura, Y. [Neutron Science Laboratory, Institute for Solid State Physics, University of Tokyo, 106-1 Shirakata, Tokai, Ibaraki 319-1106 (Japan); Nomura, H. [Department of Natural Sciences, College of Science and Engineering, Tokyo Denki University, Hiki-gun, Saitama 350-0394 (Japan)

    2007-04-30

    Dynamics of water and methylcellulose (MC) molecules in MC aqueous solution has been studied by means of quasi-elastic neutron-scattering (QENS) measurements. The dynamic structure factor S(Q,E) of the MC aqueous solution was fitted well to the sum of Lorentzian and delta functions. The former is attributed to diffusive motion of water molecules and the latter to local vibrational motion of MC molecules. The self-diffusion coefficient of water molecules was obtained from the Q dependence of the half-width at half-maximum (HWHM) of the Lorentzian function, while the mean-square displacement of MC molecules from the Q dependence of the intensity of the delta term. Both the diffusion coefficient and the mean-square displacement gradually increased on heating and abruptly decreased around the thermal gelation temperature (around 320 K). The present results revealed that the microscopic motions of both water and MC molecules give rise to dynamic slowing down on thermal gelation.

  11. Radiation crosslinking of methylcellulose and hydroxyethylcellulose in concentrated aqueous solutions

    Science.gov (United States)

    Wach, Radoslaw A.; Mitomo, Hiroshi; Nagasawa, Naotsugu; Yoshii, Fumio

    2003-12-01

    The effects of ionizing radiation on aqueous solutions of cellulose ethers, methylcellulose (MC) and hydroxyethylcellulose (HEC) were investigated. The well-established knowledge states that cellulose and its derivatives belong to degrading type of polymers. However, in our study intermolecular crosslinking initiated by gamma rays or electron beam leaded to the formation of insoluble gel. This is an opposite effect of irradiation to the degradation. Paste-like form of the initial specimen, i.e. concentration 20-30%, when water plasticizes the bulk of polymer; and a high dose rate were favorable for hydrogel formation. Gel fraction up to 60% and 70% was obtained from solutions of HEC and MC, respectively. Produced hydrogels swell markedly in aqueous media by imbibing and holding the solvent. Radiation parameters of irradiation, such as yields of degradation and crosslinking and the gelation dose, were evaluated by sol-gel analysis on the basis of Charlesby-Rosiak equation. Despite of the crosslinked structure, obtained hydrogels can be included into the group of biodegradable materials. They undergo decomposition by the action of cellulase enzyme or microorganisms from compost.

  12. Pulse-Radiolysis of Aqueous KBrO4 Solutions

    DEFF Research Database (Denmark)

    Olsen, K. J.; Sehested, Knud; Appelman, L.H.

    1973-01-01

    Pulse-radiolysis of aqueous KBrO4 solutions show that BrO−4 reacts with e−aq by the reaction BrO−4 + e−aq → BrO−3 + O−. keaq + BrO−4 = (7.0 ± 0.7) × 109 M−1 sec−1. The reactions between BrO−4 and H, OH and O− are slow. The rate constants for these reactions are less than 107 M−1 sec−1.......Pulse-radiolysis of aqueous KBrO4 solutions show that BrO−4 reacts with e−aq by the reaction BrO−4 + e−aq → BrO−3 + O−. keaq + BrO−4 = (7.0 ± 0.7) × 109 M−1 sec−1. The reactions between BrO−4 and H, OH and O− are slow. The rate constants for these reactions are less than 107 M−1 sec−1....

  13. New terahertz dielectric spectroscopy for the study aqueous solutions

    CERN Document Server

    George, Deepu K; Vinh, N Q

    2015-01-01

    We present a development of a high precision, tunable far-infrared (terahertz) frequency-domain dielectric spectrometer for studying the dynamics of biomolecules in aqueous solutions in the gigahertz-to-terahertz frequency. As a first application we report on the measurement of the absorption and refractive index for liquid water in the frequency range from 5 GHz to 1.12 THz (0.17 to 37.36 cm-1 or 0.268 to 60 mm). The system provides a coherent radiation source with a power up to 20 mW in the gigahertz-to-terahertz region. The power signal-to-noise ratio of our instrument reaches 1015 and the system achieves a spectral resolution of less than 100 Hz. The temperature of samples can be controlled precisely with an error bars of 0.02 oC from above 0 oC to 90 oC. Given these attributes, our spectrometer provides unique capabilities for the accurate measurement of even very strongly absorbing materials such as aqueous solutions.

  14. Examination of rheological properties of aqueous solutions of sodium caseinate

    Directory of Open Access Journals (Sweden)

    Jolanta Gawałek

    2012-12-01

    Full Text Available Application of sodium caseinate as a functional additive in manufacturing processes requires production of its concentrated aqueous solutions which, in industrial conditions, presents a number of difficulties. In order to develop an effective and optimal industrial process of mixing – manufacturing a concentrated solution of sodium caseinate, it is essential to know rheological properties in a definite range of concentrations changing in the course of the dissolving process. The material for investigations was typical commercial sodium caseinate in the form of dry powder manufactured in Poland from acid casein using the method of extrusion. The objective of the undertaken empirical studies was the assessment of the impact of the concentration on rheological properties of sodium caseinate concentrates. Investigations were carried out for five concentrates manufactured in a mixer equipped in a mechanical agitator at concentrations ranging X (% Î (2.5¸12.5 and changing mass proportions of sodium caseinate in the aqueous solution as follows: GS/G (kgS·kg-1 = 0.025. On the basis of the obtained research results, classical flow curves were plotted for individual concentrates. The determined values of viscosity and density of the examined solutions were correlated in the form of h = f(GS/G and r = f(GS/G dependencies which were used during the determination of classical characteristics of mixing forces essential for the assessment of energetic expenditures required to manufacture concentrates in a mixer equipped in a mechanical agitator. The density of the examined concentrates increased in a way directly proportional, while the dynamic viscosity coefficient increased exponentially together with the increase of sodium caseinate concentration. Sodium caseinate concentrates exhibited Newtonian character in the examined range of concentrations.

  15. Population and size distribution of solute-rich mesospecies within mesostructured aqueous amino acid solutions.

    Science.gov (United States)

    Jawor-Baczynska, Anna; Moore, Barry D; Lee, Han Seung; McCormick, Alon V; Sefcik, Jan

    2013-01-01

    Aqueous solutions of highly soluble substances such as small amino acids are usually assumed to be essentially homogenous systems with some degree of short range local structuring due to specific interactions on the sub-nanometre scale (e.g. molecular clusters, hydration shells), usually not exceeding several solute molecules. However, recent theoretical and experimental studies have indicated the presence of much larger supramolecular assemblies or mesospecies in solutions of small organic and inorganic molecules as well as proteins. We investigated both supersaturated and undersaturated aqueous solutions of two simple amino acids (glycine and DL-alanine) using Dynamic Light Scattering (DLS), Brownian Microscopy/Nanoparticles Tracking Analysis (NTA) and Cryogenic Transmission Electron Microscopy (Cryo-TEM). Colloidal scale mesospecies (nanodroplets) were previously reported in supersaturated solutions of these amino acids and were implicated as intermediate species on non-classical crystallization pathways. Surprisingly, we have found that the mesospecies are also present in significant numbers in undersaturated solutions even when the solute concentration is well below the solid-liquid equilibrium concentration (saturation limit). Thus, mesopecies can be observed with mean diameters ranging from 100 to 300 nm and a size distribution that broadens towards larger size with increasing solute concentration. We note that the mesospecies are not a separate phase and the system is better described as a thermodynamically stable mesostructured liquid containing solute-rich domains dispersed within bulk solute solution. At a given temperature, solute molecules in such a mesostructured liquid phase are subject to equilibrium distribution between solute-rich mesospecies and the surrounding bulk solution.

  16. Effects of the aqueous extract solution of Radix Puerariae on tissues of brain, kidney, fat and pancreas in experimental diabetic rats%葛根水煎液对糖尿病大鼠脑、肾、脂肪、胰腺组织的影响

    Institute of Scientific and Technical Information of China (English)

    涂星; 卢映; 唐洪梅; 房财富

    2013-01-01

    目的:观察葛根水煎液对糖尿病大鼠的脑、肾、脂肪和胰腺组织的影响.方法:设立正常对照组、模型对照组和给药模型组,采用高脂饮食加腹腔注射链脲佐菌素(STZ)对2型糖尿病大鼠造模,运用石蜡包埋切片技术制作脑、肾、脂肪和胰腺的组织切片,并作光镜观察.结果:葛根水煎液能够较好地修复胰岛代偿性肥大,改善病理状态下的胰岛的体积和细胞形态;减小肾小球体积的病理性增大;改善糖尿病大鼠大脑皮层神经元细胞的变性以及脂肪细胞的变性、坏死和溶解等改变.结论:葛根水煎液能够修复和保护实验型糖尿病大鼠的脑、肾、脂肪和胰腺组织,改善其生理机能.%OBJECTIVE To observe the effects of the aqueous extract solution of Radix Puerariae on brain,kidney,fat and pancreas tissues.METHODS Three groups-the normal control group,model control group and experimental model group were set up.The type 2 diabetic model was established by feeding the Wistar rats with the high fat food firstly and intra-peritoneal injection with streptozotocin(STZ).The technology of paraffin wax slice was used to make the pathological section of brain,kidney,fat and pancreas tissue and then observed them under light microscope (LM).RESULTS The aqueous extract solution of Radix Puerariae was able to repair the compensatory hypertrophy of pancreatic islets and could ameliorate the volume and shape of the islet cell which was under pathological state.It could diminish the pathological dilatation of glomerulus,and ameliorate the degeneration of neuronal cells which located in cerebral cortex and the degeneration,lytic necrosis of the adipocyte.CONCLUSION The aqueous extract solution of Radix Puerariae was able to protect and repair the brain,kidney,fat and pancreatic tissue of the experimental diabetic rats,and to improve their physiological functions.

  17. Optimization and orthogonal design of an ultrasonic-assisted aqueous extraction process for extracting chlorogenic acid from dry tobacco leaves

    Institute of Scientific and Technical Information of China (English)

    Martin Tongai Mazvimba; YU Ying; CUI Zhi-Qin; ZHANG Ying

    2012-01-01

    Processing parameters for heat reflux and ultrasonic-assisted extraction techniques were optimized.Optimal operating conditions,extraction solvents and extraction yields for both methods were established.Although methanol showed high extraction efficiency in heat reflux extraction,residual amounts of methanol caused adulteration of extracts.To circumvent this drawback,a novel ultrasonic-assisted aqueous extraction process was optimized and orthogonally designed to pave the way for replacing the toxic organic solvent,methanol with water.A new approach which utilizes fractional volumes of an extraction solvent was developed to minimize solvent consumption,improve chlorogenic acid solubility in water and enhance its aqueous extraction from dried tobacco leaves.Desired trajectories for the new ultrasonic assisted aqueous extraction process were found.

  18. Relationship between solution structure and phase behavior: a neutron scattering study of concentrated aqueous hexamethylenetetramine solutions.

    Science.gov (United States)

    Burton, R C; Ferrari, E S; Davey, R J; Finney, J L; Bowron, D T

    2009-04-30

    The water-hexamethylenetetramine system displays features of significant interest in the context of phase equilibria in molecular materials. First, it is possible to crystallize two solid phases depending on temperature, both hexahydrate and anhydrous forms. Second, saturated aqueous solutions in equilibrium with these forms exhibit a negative dependence of solubility (retrograde) on temperature. In this contribution, neutron scattering experiments (with isotopic substitution) of concentrated aqueous hexamethylenetetramine solutions combined with empirical potential structure refinement (EPSR) were used to investigate the time-averaged atomistic details of this system. Through the derivation of radial distribution functions, quantitative details emerge of the solution coordination, its relationship to the nature of the solid phases, and of the underlying cause of the solubility behavior of this molecule.

  19. Treatment of sugi (Cryptomeria japonica D.) sapwood with aqueous solution of acetic acid

    Institute of Scientific and Technical Information of China (English)

    LUBao-wang; DUGuang-hua; MATSUITakanao; MATSUSHITAYoh-ichi

    2003-01-01

    Sugi sapwood samples were processed with aqueous solution of acetic acid in order to find the response of the weight of sugi sapwood and the treatment of aqueous solution of acetic acid. The result showed that loss of weight for the treated sugisapwood was about equal to yield of extracts from sugi sapwood, and increased with the increment of the concentration of aqueous solution of acetic acid. Fourier transform infrared spectroscopy spectra changes of the treated sugi wood and extracts from sugi sapwood were analyzed by FT-IR spectroscopic technique. Increasing tendency of absorption intensities of the stretching vibration at 3 400 cm-1 of hydroxyl group (OH) and C=C in lignin stretching vibration at 1510 cm-1 of benzene ring inlignin were observed from FT-IR of the treated sugi sapwood. From FT-IR spectra of extracts from sugi sapwood by aqueoussolution of acetic acid, the dissolution of lignin was observed during the treatment with 30% acetic acid solution aqueous.

  20. Effect of aqueous and ethanolic extracts of Pimpinella anisum L. seeds on milk production in rats.

    Science.gov (United States)

    Hosseinzadeh, Hossein; Tafaghodi, Mohsen; Abedzadeh, Shirin; Taghiabadi, Elahe

    2014-08-01

    Pimpinella anisum L. (P. anisum) is used as a galactagogue in traditional medicine; hence, the effect of aqueous and ethanolic extracts of P. anisum seeds on milk production in rats was evaluated. The milk production was assessed by measuring the pups' weights during the suckling period. The intraperitoneal LD(50) values of P. anisum aqueous and ethanolic extracts were 4.93 and 3.77 g/kg, respectively. The aqueous (1 g/kg) and ethanolic extracts (1 g/kg) increased the milk production significantly (p anisum aqueous and ethanolic extracts can increase milk production in rats.

  1. Separation of compounds with multiple -OH groups from dilute aqueous solutions via complexation with organoboronate

    Energy Technology Data Exchange (ETDEWEB)

    Chow, Tina Kuo Fung

    1992-05-01

    The complexing extractant agent investigated in this work is 3-nitrophenylboronic acid (NPBA) in its anionic form (NPB). NPBA and Aliquat 336 (quaternary amine) is dissolved in 2-ethyl-l-hexanol, and the extractant is contacted with aq. NaOH. Solutes investigated were 1,2-propanediol, glycerol, fructose, sorbitol and lactic acid. Batch extraction experiments were performed at 25{degree}C. Partition coefficients, distribution ratios and loadings are reported for varying concentrations of solute and NPB. All solutes complexed with NPB{sup {minus}}, with all complexes containing only one NPB{sup {minus}} per complex. The 1:1 complexation constants for the solutes glycerol, fructose and sorbitol follow trends similar to complexation with B(OH){sub 4}{sup {minus}} (aq.), i.e. the complexation constants increase with increasing number of {minus}OH groups available for complexation. Assumption of 1:1 complex is not valid for 1, 2-propanediol, which showed overloading (more than one mole of solute complexed to one mole NPB{sup {minus}}) at higher concentrations. The {minus}OH group on the NPB{sup {minus}} which is left uncomplexed after one solute molecule had bound to the other two {minus}OH groups may be responsible for the overloading. Overloading is also observed in extraction of tactic acid, but through a different mechanism. It was found that TOMA{sup +} can extract lactic acid to an extent comparable to the uptake of lactic acid by NPB{sup {minus}}. The complexation is probably through formation of an acid-base ion pair. Losses of NPBA into the aqueous phase could lead to problems, poor economics in industrial separation processes. One way of overcoming this problem would be to incorporate the NPBA onto a solid support.

  2. Adsorption of cesium on cement mortar from aqueous solutions.

    Science.gov (United States)

    Volchek, Konstantin; Miah, Muhammed Yusuf; Kuang, Wenxing; DeMaleki, Zack; Tezel, F Handan

    2011-10-30

    The adsorption of cesium on cement mortar from aqueous solutions was studied in series of bench-scale tests. The effects of cesium concentration, temperature and contact time on process kinetics and equilibrium were evaluated. Experiments were carried out in a range of initial cesium concentrations from 0.0103 to 10.88 mg L(-1) and temperatures from 278 to 313 K using coupons of cement mortar immersed in the solutions. Non-radioactive cesium chloride was used as a surrogate of the radioactive (137)Cs. Solution samples were taken after set periods of time and analyzed by inductively coupled plasma mass spectroscopy. Depending on the initial cesium concentration, its equilibrium concentration in solution ranged from 0.0069 to 8.837 mg L(-1) while the respective surface concentration on coupons varied from 0.0395 to 22.34 μg cm(-2). Equilibrium test results correlated well with the Freundlich isotherm model for the entire test duration. Test results revealed that an increase in temperature resulted in an increase in adsorption rate and a decrease in equilibrium cesium surface concentration. Among several kinetic models considered, the pseudo-second order reaction model was found to be the best to describe the kinetic test results in the studied range of concentrations. The adsorption activation energy determined from Arrhenius equation was found to be approximately 55.9 kJ mol(-1) suggesting that chemisorption was the prevalent mechanism of interaction between cesium ions and cement mortar.

  3. Electrical conductivity of aqueous solutions of aluminum salts

    Science.gov (United States)

    Vila, J.; Rilo, E.; Segade, L.; Cabeza, O.; Varela, L. M.

    2005-03-01

    We present experimental measurements of the specific electrical conductivity (σ) in aqueous solutions of aluminum salts at different temperatures, covering all salt concentrations from saturation to infinite dilution. The salts employed were AlCl3 , AlBr3 , AlI3 , and Al(NO3)3 , which present a 1:3 relationship between the electrical charges of anion and cation. In addition, we have measured the density in all ranges of concentrations of the four aqueous electrolyte solutions at 298.15K . The measured densities show an almost linear behavior with concentration, and we have fitted it to a second order polynomial with very high degree of approximation. The measurement of the specific conductivity at constant temperature reveals the existence of maxima in the conductivity vs concentration curves at molar concentrations around 1.5M for the three halide solutions studied, and at approximately 2M for the nitrate. We present a theoretical foundation for the existence of these maxima, based on the classical Debye-Hückel-Onsager hydrodynamic mean-field framework for electrical transport and its high concentration extensions, and also a brief consideration of ionic frictional coefficients using mode-coupling theory. We also found that the calculated values of the equivalent conductance vary in an approximately linear way with the square root of the concentration at concentrations as high as those where the maximum of σ appears. Finally, and for completeness, we have measured the temperature dependence of the electrical conductivity at selected concentrations from 283to353K , and performed a fit to an exponential equation of the Vogel-Fulcher-Tamman type. The values of the calculated temperatures of null mobility of the four salts are reported.

  4. Anti-influenza virus effect of aqueous extracts from dandelion

    Directory of Open Access Journals (Sweden)

    He Wen

    2011-12-01

    Full Text Available Abstract Background Human influenza is a seasonal disease associated with significant morbidity and mortality. Anti-flu Traditional Chinese Medicine (TCM has played a significant role in fighting the virus pandemic. In TCM, dandelion is a commonly used ingredient in many therapeutic remedies, either alone or in conjunction with other natural substances. Evidence suggests that dandelion is associated with a variety of pharmacological activities. In this study, we evaluated anti-influenza virus activity of an aqueous extract from dandelion, which was tested for in vitro antiviral activity against influenza virus type A, human A/PR/8/34 and WSN (H1N1. Results Results obstained using antiviral assays, minigenome assay and real-time reverse transcription-PCR analysis showed that 0.625-5 mg/ml of dandelion extracts inhibited infections in Madin-Darby canine kidney (MDCK cells or Human lung adenocarcinoma cell line (A549 of PR8 or WSN viruses, as well as inhibited polymerase activity and reduced virus nucleoprotein (NP RNA level. The plant extract did not exhibit any apparent negative effects on cell viability, metabolism or proliferation at the effective dose. This result is consistent with the added advantage of lacking any reported complications of the plant's utility in traditional medicine over several centuries. Conclusion The antiviral activity of dandelion extracts indicates that a component or components of these extracts possess anti-influenza virus properties. Mechanisms of reduction of viral growth in MDCK or A549 cells by dandelion involve inhibition on virus replication.

  5. Arsenic Removal from Aqueous Solutions by Salvadora persica Stem Ash

    Directory of Open Access Journals (Sweden)

    Ferdos Kord Mostafapour

    2013-01-01

    Full Text Available Arsenic is a naturally occurring metalloid, which is widely distributed in nature and is regarded as the largest mass poisoning in history. In the present study, the adsorption potential of Salvadora persica (S. persica stem ash in a batch system for the removal of As(V from aqueous solutions was investigated. Isotherm studies were carried out to evaluate the effect of contact time (20–240 min, pH (2–11, initial arsenic concentration (50–500 μg/L, and adsorbent dose on sorption efficiency. Maximum removal efficiency of 98.33% and 99.32% was obtained at pH 6, adsorbent dosage 3.5 g/L, initial As(V concentration 500 μg/L, and contact time 80 and 60 min for S. persica stem ash at 300 °C and 500 °C, respectively. Also, the adsorption equilibriums were analyzed by the Langmuir and Freundlich isotherm models. Such equilibriums showed that the adsorption data was well fitted with the Freundlich isotherm model for S. persica stem ash at both 300 °C and 500 °C (R2=0.8983 and 0.9274, resp.. According to achieved results, it was defined that S. persica stem ash can be used effectively for As(V removal from the aqueous environment.

  6. Colloidal Stability of Graphene Oxide Nanosheets in Aqueous Solutions

    Science.gov (United States)

    Guikema, Janice; Wang, Yung-Li; Chen, Kai

    2013-03-01

    Carbon-based nanomaterials are increasingly used in commercial products as well as in research and industrial applications. Due to its extraordinary properties, graphene has attracted intense research interest and has been demonstrated in many potential applications including solar cells, conductive ink, and transistors. Graphene oxide has also been studied extensively and has been used to produce biocompatible antibacterial paper. Chemical reduction of graphene oxide is commonly used to produce inexpensive graphene in large quantities. With the increasing use of graphene and graphene oxide in consumer products, these nanomaterials may inevitably be released to aqueous systems, resulting in potential risk to environmental ecosystems and human health. The fate and mobility of graphene and its oxides in aquatic systems is dependent on their colloidal stability. We will discuss our study of the early-stage aggregation kinetics of graphene oxide in aqueous solutions. We prepared a suspension of single-layer graphene oxide nanosheets in water and used time-resolved dynamic light scattering to study the influence of electrolytes and pH on the aggregation kinetics of the nanosheets. Atomic force microscopy was employed to further examine the graphene oxide nanosheets.

  7. Comparison of Photochemical Reactions of m-Cresol in Aqueous Solution and in Ice

    Institute of Scientific and Technical Information of China (English)

    PENG Fei; XUE Hong-hai; TANG Xiao-jian; KANG Chun-li; LI Lin-lin; LI Zhe

    2012-01-01

    We compared the photochemical reaction of m-cresol containing OH precursors such as H2O2,NO2- and NO3- in aqueous solution with those in ice.The results show that the conversion rate of m-cresol in aqueous solution was higher than that in ice,H2O2,NO2- and NO3- all accelerated the photoconversion of m-cresol in both aqueous solution and ice.The photochemical reactions of m-cresol obeys the first order kinetics equation.According to the photoproducts identified by GC-MS,we proposed that hydroxylation and nitration reactions occurred in both aqueous solution and ice.Coupling reaction was common in ice,however,in aqueous solution it was found only in UV system.Our results suggest that the photochemical reactions of m-cresol were different in aqueous solution and in ice.

  8. Mechanism of extractant loss in solvent extraction process (Ⅰ)——Transfer of saponified D2EHPA from organic phase to aqueous phase and its aggregation behaviour

    Institute of Scientific and Technical Information of China (English)

    王笃金; 吴瑾光; 李彦; 翁诗甫; 吴佩强; 徐光宪

    1995-01-01

    The phenomenon of the loss of saponified D2EHPA(di(2-ethylhexyl)phosphoric acid,HA)from organic phase to aqueous phase and its aggregation behaviour were studied with FT-IR and DLS(dynamic light scattering)techniques based on the fact that saponified extractant can form reversed micelles orw/o microemulsions in n-heptane,a non-polar diluent.The results indicate that "normal rnioelles" or o/wmicroemulsions are formed from acidic extractant and its sodium salt in aqueous phase,and the micelle ormicroemulsion drop has a non-polar core which can solubilize nheptane,so the equilibrated aqueous phasecontaining extractant is a complex fluid rather than a "real solution".Therefore,the aqueous aggregate for-mation leads to the extractant loss in solvent extraction process.Strong electrolytes can prevent or lessen theextractant loss.The results of this paper provide a theoretical possibility for solving the problem ofextractant and solvent loss in liquid-liquid extraction industry.

  9. ACUTE TOXICITY OF THE AQUEOUS EXTRACT FROM BRILLANTAISIA VOGELIANA (NÉES BENTH. (ACANTHACEAE

    Directory of Open Access Journals (Sweden)

    Aimé Valère SOH OUMBE

    2013-04-01

    Full Text Available Brillantaisia vogeliana (Acanthacées is a plant used in the West-Cameroon traditional pharmacopeia. This species have been used to facilitate deliverance and delivery and to treat stomach ailment. The aqueous extract of leaves was studied by conventional pharmacological methods.Twelve female rats were randomly assigned in two groups of 6 animals each designated as control and treated groups. After a sighting study, one group of the fasted animals for 12h received a single oral dose of 2000 mg/kg body weight of aqueous solution of Brillantaisia vogeliana while control group received distilled water.Oral consumption of 2 g/kg of Brillantaisia vogeliana produced neither mortality nor significant differences in the body and relative organs weights except relative liver weight between control and treated animals. Moreover, no abnormality and no histopathological changes were detectable between both control and treated animals. Hematological analysis showed no difference in any of the parameters tested (WBC count, platelet, total leukocytes, RBC count, hematocrit and hemoglobin estimation in either control or treated groups. No significant change occurred in the blood chemistry parameters, including creatinine, urea nitrogen (UN, alkaline phosphatase, aspartate amino transferase (ASAT, alanine aminotransferase (ALAT, calcium and phosphorus. However, α-amylase and total protein showed a significant difference between control and treated groups. The results showed the innocuity of the aqueous extract of B. vogeliana and thus validated its utilization in Cameroonian traditional pharmacopoeia. The LD50 was higher than 2g/kg of body weight and according to Globally Harmonized Hazard Classification and Labelling Scheme (GHS, aqueous extract of B. vogeliana was classified in group 5.

  10. Study of the nanobubble phase of aqueous NaCl solutions by dynamic light scattering

    Energy Technology Data Exchange (ETDEWEB)

    Bunkin, N F; Shkirin, A V [A M Prokhorov General Physics Institute, Russian Academy of Sciences, Moscow (Russian Federation); Burkhanov, I S; Chaikov, L L [P N Lebedev Physics Institute, Russian Academy of Sciences, Moscow (Russian Federation); Lomkova, A K [N.E. Bauman Moscow State Technical University, Moscow (Russian Federation)

    2014-11-30

    Aqueous NaCl solutions with different concentrations have been investigated by dynamic scattering of laser radiation. It is experimentally shown that these solutions contain scattering particles with a wide size distribution in a range of ∼10 – 100 nm. The experimental results indirectly confirm the existence of quasi-stable gas nanobubbles in the bulk of aqueous ionic solutions. (light scattering)

  11. Adsorption of catechol from aqueous solution by aminated hypercrosslinked polymers

    Institute of Scientific and Technical Information of China (English)

    SUN Yue; LI Xiao-tao; XU Chao; CHEN Jin-long; LI Ai-min; ZHANG Quan-xing

    2005-01-01

    Adsorption of catechol from aqueous solution with the hypercrosslinked polymeric adsorbent NDA-100 and its derivatives AH-1,AH-2 and AH-3 aminated by dimethylamine, the commercial resin Amberlite XAD-4 and weakly basic anion exchanger resin D301 was compared. It was found that the aminated hypercrosslinked resins had the highest adsorption capacities among the tested polymers. The empirical Freundlich equation was successfully employed to describe the adsorption process. Specific surface area and micropore structure of the adsorbent, in company with tertiary amino groups on matrix affected the adsorption performance towards catechol. In addition,thermodynamic study was carried out to interpret the adsorption mechanism. Kinetic study testified that the tertiary amino groups on the polymer matrix could decrease the adsorption rate and increase the adsorption apparent activation energy.

  12. Adsorption of Anthraquinone Dyes from Aqueous Solutions by Penicillium Terrestre

    Institute of Scientific and Technical Information of China (English)

    XIN Bao-ping; LIU Xiao-mei

    2006-01-01

    Penicillium terrestre was used for removing four anthraquinone dyes from aqueous solution. The experiments were performed in Erlenmeyer flasks and spore suspension was used for inoculation. The results show that the mechanism of dye removal by penicillium terrestre is biosorption and the growing pellets exhibit higher adsorptive capacity than the resting or dead ones. The maximum removals of disperse blue 2BLN, reactive brilliant blue KN-R, acid anthraquinone blue and bromamine acid at the concentration of 120 mg/L by biosorption of growing pellets are 100 %, 100 %, 96 % and 91%, respectively. The 100.0 % and 91.4 % KN-R removals are achieved respectively at the much higher concentration of 250 and 400 mg/L. 2.5 g/L glucose is sufficient for 100% KN-R removal by growing pellets. Salinity (NaC1) increase from 0 to 2% (W/V) moderately accelerates both mycelium growth and KN-R removal.

  13. Degradation of aqueous solutions of camphor by heterogeneous photocatalysis.

    Science.gov (United States)

    Sirtori, Carla; Altvater, Priscila K; de Freitas, Adriane M; Peralta-Zamora, Patricio G

    2006-02-28

    In this study the photocatalytic degradation of aqueous solutions of camphor was investigated by using TiO2 and ZnO photocatalysts. In the presence of artificial UV-light the highly photosensitive camphor was almost totally degraded after reaction times of 60 min. However, under these conditions the mineralization degree was lower than 25%. In the presence of semiconductors the degradation was complete after a treatment time of about 30 min. Moreover, the mineralization was considerably greater, mainly with the use of TiO2 (> 80% at reaction time of 60 min). Heterogeneous photocatalytic processes applied in the presence of solar radiation show a promising degradation capability. TiO2-based processes afforded mineralization degrees of about 90% after a reaction time of 120 min, when the system was assisted by aeration.

  14. Microfluidic synthesis of monodisperse Cu nanoparticles in aqueous solution.

    Science.gov (United States)

    Ke, Te; Zeng, Xiao-Fei; Wang, Jie-Xin; Le, Yuan; Chu, Guang-Wen; Chen, Jian-Feng; Shao, Lei

    2011-06-01

    The continuous production of Cu nanoparticles with a particle size of 2-5 nm was conducted by sodium borohydride reduction of copper sulfate in aqueous solution in a tube-in-tube microchannel reactor (TMR), which consists of an inner tube and an outer tube with the reaction performed in the annular microchannel between these two tubes. The as-prepared Cu nanoparticles were compared with those obtained by a conventional batch synthesis process by using transmission electron microscopy (TEM), X-ray diffraction (XRD) and UV-vis spectroscopy. Due to the highly intensified micromixing effects in the TMR, Cu nanoparticles prepared by this route exhibits a smaller particle size, narrower size distribution and better stability in air. The TMR shows an excellent ability of preparing high-quality Cu nanoparticles in mild conditions. In addition, with the unique microchannel structure, the throughput capability of the TMR for the production of Cu nanoparticles is up to several liters per minute.

  15. Conformation of poly(γ-glutamic acid) in aqueous solution.

    Science.gov (United States)

    Muroga, Yoshio; Nakaya, Asami; Inoue, Atsuki; Itoh, Daiki; Abiru, Masaya; Wada, Kaori; Takada, Masako; Ikake, Hiroki; Shimizu, Shigeru

    2016-04-01

    Local conformation and overall conformation of poly(γ-DL-glutamic acid) (PγDLGA) and poly(γ-L-glutamic acid) (PγLGA) in aqueous solution was studied as a function of degree of ionization ε by (1) H-NMR, circular dichroism, and potentiometric titration. It was clarified that their local conformation is represented by random coil over an entire ε range and their overall conformation is represented by expanded random-coil in a range of ε > ε(*) , where ε(*) is about 0.3, 0.35, 0.45, and 0.5 for added-salt concentration of 0.02M, 0.05M, 0.1M, and 0.2M, respectively. In a range of ε acidic media.

  16. Application of ultrasound to textiles washing in aqueous solutions.

    Science.gov (United States)

    Gotoh, Keiko; Harayama, Kokoro

    2013-03-01

    The ultrasound was applied to textile washing as a mechanical action for soil removal. The polyester fabric was soiled with carbon black or oleic acid as a model contaminant, and washed with the original fabric in aqueous solutions without and with alkali or surfactant by applying ultrasound, shaking or stirring action. The detergency and soil redeposition were evaluated from the change in the surface reflectance of artificially soiled fabrics and the original fabric due to washing. In comparison with shaking and stirring actions, ultrasound was found to remove the particulate and oily soils efficiently in a short time and at low bath ratio. With increasing ultrasound power, the detergency of both soils increased and exceeded that obtained with Wascator, a horizontal axis drum type washer. Using three standard fabrics for determining mechanical action during washing, it was shown that ultrasound washing caused little mechanical damage to the fabric. However, the soil redeposition was frequently observed for ultrasonic washing, especially at low bath ratio.

  17. Aqueous dispersions of silver nanoparticles in polyelectrolyte solutions

    Indian Academy of Sciences (India)

    Dan Donescu; Raluca Somoghi; Marius Ghiurea; Raluca Ianchis; Cristian Petcu; Stefania Gavriliu; Magdalena Lungu; Claudia Groza; Carmen R Ionescu; Carmen Panzaru

    2013-03-01

    In this report, we present the versatile and effective technique, using environmental friendly reductant glucose, to prepare stable silver nanodispersions by reduction of Ag+ ions. Alternant copolymers of maleic anhydride with vinyl acetate and styrene sulphonate sodium acid salt polyelectrolytes were synthesized in aqueous solution and used as stabilizers. The formation of nano silver particles was confirmed by UV-Vis spectrophotometry and TEM measurements. Dynamic Light Scattering (DLS) measurements were needed to study how the reagents and their concentrations influence particle size. SEM images show the nanostructure of the hybrid films and indicate a strong interaction between the polyelectrolyte and the silver NPs. Moreover, the silver NPs could be stored for one year without observation of aggregates or sedimentation. The final solid products obtained after evaporating to dryness can be used to produce stable dispersions upon mixing with water. Few of the final products were found to exhibit a high antibacterial and antifungal activity.

  18. Transport Process of Isopropanol Aqueous Solution by Pervaporation

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    To study the transport process of isopropanol aqueous solution by pervaporation, the transport model of isopropanol and that of water at 323 K in polyvinyl alcohol(PVA) membrane were obtained in this paper. Theoretical predictions agreed well with the experimental results. The interactional parameter between water and PVA membrane is less than that between isopropanol and PVA membrane, which shows that water is preferentially dissolved in PVA membrane. The plasticizing coefficient and diffusion coefficient at infinite dilution of water are larger than those of isopropanol,which shows that the dissolution and permeation in PVA membrane of water are greater than those of isopropanol. Both the interactional parameter between water and isopropanol in the membrane and that in feed rise with the increase of isopropanol content in feed, which shows that the larger isopropanol content is, the higher selectivity of the membrane is and the more remarkable separation effect of pervaporation is.

  19. Adsorption of basic dye from aqueous solution onto fly ash

    Energy Technology Data Exchange (ETDEWEB)

    J.X. Lin; S.L. Zhan; M.H. Fang; X.Q. Qian; H. Yang [Zhejiang University, Hangzhou (China). College of Civil Engineering and Architecture

    2008-04-15

    The fly ash treated by H{sub 2}SO{sub 4} was used as a low-cost adsorbent for the removal of a typical dye, methylene blue, from aqueous solution. An increase in the specific surface area and dye-adsorption capacity was observed after the acid treatment. The adsorption isotherm and kinetics of the treated fly ash were studied. The experimental results were fitted using Langmuir and Freundlich isotherms. It shows that the Freundlich isotherm is better in describing the adsorption process. Two kinetic models, pseudo-first order and pseudo-second order, were employed to analyze the kinetic data. It was found that the pseudo-second-order model is the better choice to describe the adsorption behavior. The thermodynamic study reveals that the enthalpy ({Delta}H{sup 0}) value is positive (5.63 kJ/mol), suggesting an endothermic nature of the adsorption.

  20. Adsorption of CTAB onto perlite samples from aqueous solutions.

    Science.gov (United States)

    Alkan, Mahir; Karadaş, Mecit; Doğan, Mehmet; Demirbaş, Ozkan

    2005-11-15

    In this study, the adsorption properties of unexpanded and expanded perlite samples in aqueous cetyltrimethylammonium bromide (CTAB) solutions were investigated as a function of ionic strength, pH, and temperature. It was found that the amount of cetyltrimethylammonium bromide adsorbed onto unexpanded perlite was greater than that onto expanded perlite. For both perlite samples, the sorption capacity increased with increasing ionic strength and pH and decreasing temperature. Experimental data were analyzed by Langmuir and Freundlich isotherms and it was found that the experimental data were correlated reasonably well by the Freundlich adsorption isotherm. Furthermore, the isotherm parameters (KF and n) were also calculated. The adsorption enthalpy was determined from experimental data at different temperatures. Results have shown that the interaction between the perlite surface and CTAB is a physical interaction, and the adsorption process is an exothermic one.

  1. Infrared spectroscopy for monitoring gas hydrates in aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Dobbs, G.T.; Luzinova, Y.; Mizaikoff, B. [Georgia Inst. of Technology, Atlanta, GA (United States). School of Chemistry and Biochemistry; Raichlin, Y.; Katzir, A. [Tel-Aviv Univ., Tel-Aviv (Israel). Shool of Physics and Astronomy

    2008-07-01

    This paper introduced the first principles for monitoring gas hydrate formation and dissociation in aqueous solution by evaluating state-responsive infrared (IR) absorption features of water with fiberoptic evanescent field spectroscopy. A first order linear functional relationship was also derived according to Lambert Beer's law in order to quantify the percentage gas hydrate within the volume of water probed via the evanescent field. In addition, spectroscopic studies evaluating seafloor sediments collected from a gas hydrate site in the Gulf of Mexico revealed minimal spectral interferences from sediment matrix components. As such, evanescent field sensing strategies were established as a promising perspective for monitoring the dynamics of gas hydrates in oceanic environments. 21 refs., 5 figs.

  2. Formation of wormlike micelles in anionic surfactant AES aqueous solutions

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The growth and structure of anionic micelles of sodium dodecyl trioxyethylene sulfate (AES) in the presence 3+of multivalent counterion Al were investigated by means of dynamic rheological methods. It has been obtained by the measurements of shear viscosity, complex viscosity and dynamic moduli, as well as the application of Cox-Merz rule and Cole-Cole plot that wormlike micelle and network structure could be formed in AES/AlCl3 aqueous solutions.The structure was of a character of nonlinear viscoelastic fluid and departure from the simple Maxwell model. The technique of freeze-fracture transmission electron microscopy (FF-TEM) was also used to confirm the formation of this interesting structure.``

  3. Experimental study on thermophoresis of colloids in aqueous surfactant solutions

    Science.gov (United States)

    Dong, Ruo-Yu; Zhou, Yi; Yang, Chun; Cao, Bing-Yang

    2015-12-01

    Thermophoresis refers to the motion of particles under a temperature gradient and it is one of the particle manipulation techniques. Regarding the thermophoresis of particles in liquid media, however, many open questions still remain, especially the role of the interfacial effect. This work reports on a systematic experimental investigation of surfactant effects, especially the induced interfacial effect, on the thermophoresis of colloids in aqueous solutions via a microfluidic approach. Two kinds of commonly used surfactants, sodium dodecyl sulfate (SDS) and cetyltrimethylammonium bromide (CTAB), are selected and the results show that from relatively large concentrations, the two surfactants can greatly enhance the thermophilic mobilities. Specifically, it is found that the colloid-water interfaces modified with more polar end groups can potentially lead to a stronger thermophilic tendency. Due to the complex effects of surfactants, further theoretical model development is needed to quantitatively describe the dependence of thermophoresis on the interface characteristics.

  4. γ-Irradiation of malic acid in aqueous solutions

    Science.gov (United States)

    Negron-Mendoza, Alicia; Graff, Rebecca L.; Ponnamperuma, Cyril

    1980-12-01

    The γ-irradiation of malic acid in aqueous solutions was studied under initially oxygenated and oxygen-free conditions in an attempt to determine the possible interconversion of malic acid into other carboxylic acids, specifically those associated with Krebs cycle. The effect of dose on product formation of the system was investigated. Gas-liquid chromatography combined with mass spectrometry was used as the principal means of identification of the non-volatile products. Thin layer chromotography and direct probe mass spectroscopy were also employed. The findings show that a variety of carboxylic acids are formed, with malonic and succinic acids in greatest abundance. These products have all been identified as being formed in the γ-irradiation of acetic acid, suggesting a common intermediary. Since these molecules fit into a metabolic cycle, it is strongly suggestive that prebiotic pathways provided the basis for biological systems.

  5. Removal of lead from aqueous solutions by Penicillium biomass

    Energy Technology Data Exchange (ETDEWEB)

    Hui Niu; Xue Shu Xu; Jian Hua Wang (Chengdu Univ. of Science and Technology, Sichuan (China). Dept. of Chemical Engineering); Volesky, B. (McGill Univ., Montreal (Canada). Dept. of Chemical Engineering)

    1993-09-05

    The removal of lead ions from aqueous solutions by adsorption on nonliving Penicillium chrysogenum biomass was studied. Biosorption of the Pb[sup +2] ion was strongly affected by pH. Within a pH range of 4 to 5, the saturated sorption uptake of Pb[sup +2] was 116 mg/g dry biomass, higher than that of activated charcoal and some other microorganisms. At pH 4.5, P. chrysogenum biomass exhibited selectivity for Pb[sup +2] over other metal ions such as Cd[sup +2], Cu[sup +2], Zn [sup +2], and As[sub +3]. Sorption preference for metals decreased in the following order: Pb > Cd > Cu > Zn > As. The sorption uptake of Pb[sup +2] remained unchanged in the presence of Cu[sup +2] and As [sup +3], it decreased in the presence of Zn[sup +2], and increased in the presence of Cd[sup +2].

  6. VISCOSITY BEHAVIOR OF LACQUER POLYSACCHARIDE IN AQUEOUS SOLUTION

    Institute of Scientific and Technical Information of China (English)

    QIU Xingping; ZHANG Lina; DU Yumin; QIAN Baogong

    1991-01-01

    The dependence of measured viscosity on NaCl concentration (0.1 to 3.0M), pH (range of 2-13) and cadoxen composition Wcad (from 2% to 100% ) for the lacquer polysaccharide in NaCl/cadoxen/H2O mixture containing HCl or without were obtained. All the viscosity exponents γ in the Mark-Houwink equations under three different solvent condition are close to 0.5. The wcad dependence of reduced viscosity ηsp/c confirms the single strand chain of the polysaccharide. As the γ values close to 0.5 and values of unperturbed dimension θ/M and [η] much smaller than those for usual linear polymers, these facts suggest that the polysaccharide chains in the aqueous solutions should be dense random coil owing to the highly branched structure.

  7. Ultrasonic Measurements of Temperature in Aqueous Solutions: Why and How

    Directory of Open Access Journals (Sweden)

    A. Afaneh

    2011-01-01

    Full Text Available The paper describes two different approaches to ultrasonic measurements of temperature in aqueous solutions. The first approach uses two narrowband ultrasonic transducers and support electronics that form an oscillating sensor which output frequency is related to the measured temperature. This low-cost sensor demonstrated sensitivity of about 40 Hz/K at the distance of 190 mm and the operating frequency of about 25 kHz. The second approach utilised pulse-echo mode at the centre frequency of 20 MHz. The reflector featured a cavity that was filled with deionised water. The ultrasound propagation delay in the cavity was related to the temperature in the solution. The experiments were conducted for deionised water, and solutions of sodium persulfate, sodium chloride, and acetic acid with concentrations up to 0.5 M. In the experiments (conducted within the temperature range from 15 to 30°C, we observed increases in the ultrasound velocity for increased temperatures and concentrations as was expected. Measurement results were compared with literature data for pure and seawater. It was concluded that ultrasonic measurements of temperature were conducted with the resolution well below 0.1 K for both methods. Advantages of ultrasonic temperature measurements over conventional thermometers were discussed.

  8. Aqueous solution of basic fuchsin as food irradiation dosimeter

    Institute of Scientific and Technical Information of China (English)

    Hasan M. KHAN; Shagufta NAZ

    2007-01-01

    Dosimetric characterization of aqueous solution of basic fuchsin was studied spectrophotometrically for possible application in the low-dose food irradiation dosimetry. Absorption spectra of unirradiated and irradiated solutions were determined and the decrease in absorbance with the dose was noted down. Radiation-induced bleaching of the dye was measured at wavelengths of maximum absorption λmax (540nm) as well as 510nm and 460 nm. At all these wavelengths, the decrease in absorbance of the dosimeter was linear with respect to the absorbed dose from 50 Gy to 600 Gy. The stability of dosimetric solution during post-irradiation storage in the dark at room temperature showed that after initial bleaching during first ten to twenty days, the response was almost stable for about 34 days. The study on the effect of different light and temperature conditions also showed that the response gradually decreased during the storage period of 34 days, which shows that basic fuchsin dye is photosensitive as well as thermally sensitive.

  9. Hydrophobicity and thermodynamic response for aqueous solutions of amphiphiles

    Science.gov (United States)

    Zemánková, Katerina; Troncoso, Jacobo; Cerdeiriña, Claudio A.; Romaní, Luis; Anisimov, Mikhail A.

    2016-06-01

    The anomalous behavior of aqueous solutions of amphiphiles in the water-rich region is analyzed via a phenomenological approach that utilizes the isobaric heat capacity Cp as an experimental probe. We report extensive data for solutions of 14 amphiphiles as a function of temperature at atmospheric pressure. Beyond that, Cp data but also isobaric thermal expansivities and isothermal compressibilities for three solutions of tert-butanol as a function of both temperature and pressure are presented. Results rule out the possibility that the observed phenomenology is associated with the anomalous thermodynamics of pure water. Indeed, our Cp data, quantitatively consistent with recent spectroscopic analyses, suggest that water-mediated interactions between the nonpolar parts of amphiphiles are at the origin of anomalies, with the effects of such "hydrophobic aggregation" being observed at mole fractions as small as 0.01. Physicochemical details like the size, the electronic charge distribution and the geometry of amphiphile molecules as well as third-order derivatives of the Gibbs energy and the associated Koga lines support the above claims while they further contribute to characterizing the role of hydrophobicity in these phenomena. Progress with a view to gain a deeper, more concrete understanding remains.

  10. Carbon dioxide capture capacity of sodium hydroxide aqueous solution.

    Science.gov (United States)

    Yoo, Miran; Han, Sang-Jun; Wee, Jung-Ho

    2013-01-15

    The present paper investigates the various features of NaOH aqueous solution when applied as an absorbent to capture carbon dioxide (CO(2)) emitted with relatively high concentration in the flue gas. The overall CO(2) absorption reaction was carried out according to consecutive reaction steps that are generated in the order of Na(2)CO(3) and NaHCO(3). The reaction rate and capture efficiency were strongly dependent on the NaOH concentration in the Na(2)CO(3) production range, but were constant in the NaHCO(3) production step, irrespective of the NaOH concentration. The amount of CO(2) absorbed in the solution was slightly less than the theoretical value, which was ascribed to the low trona production during the reaction and the consequent decrease in CO(2) absorption in the NaOH solution. The mass ratio of absorbed CO(2) that participated in the Na(2)CO(3), NaHCO(3), and trona production reactions was calculated to be 20:17:1, respectively.

  11. The anti-cancer effect of Huaier aqueous extract with rh-Endostatin and DDP

    Institute of Scientific and Technical Information of China (English)

    Yuxuan Che; Meixiang Zhou; Peng Zhan; Tiantian Zou; Xiuhua Sun

    2014-01-01

    The-aim-of-our-study-was-to-explore-the-inhibition-and-apoptosis-inducing-ef-ect-of-the-combination-of-Huaier-aqueous-extract-with-recombinant-human-Endostatin-and-DDP-in-human-lung-adenocarcinoma-A549-cel-s.-We-also-investigated-the-reversal-ef-ect-of-Huaier-aqueous-extract-in-reversing-cisplatin-resistance-in-human-lung-adenocarcinoma-A549/DDP-cel-s.-Methods:We-treated-A549-cel-s-with-Huaier-aqueous-extract-and-the-combination-of-Huaier-aqueous-ex-tract-and-DDP-or-rh-Endostatin-for-24-h,-36-h-and-48-h.-And-then-we-calculated-the-inhibition-rate-through-MTT-approach-and-detected-the-apoptosis-rate-by-flow-cytometry.-We-also-treated-A549-and-A549/DDP-cel-s-with-DDP,-Huaier-aqueous-extract,-DDP-and-Huaier-aqueous-extract-for-72-h,-respectively.-Results:Huaier-aqueous-extract-can-inhibit-the-growth-of-A549-cel-s-and-the-inhibition-rate-improved-with-the-increase-of-the-concentration.-The-inhibition-rate-of-the-combination-of-rh-Endostatin-and-4-mg/mL-of-Huaier-aqueous-extract-in-three-time-points-and-the-combination-of-rh-Endostatin-and-2-mg/mL-of-Huaier-aqueous-extract-in-the-time-point-of-48-h-on-the-growth-of-A549-cel-s-al-improved-(P<0.005).-The-inhibition-rate-of-the-com-bination-of-DDP-and-Huaier-aqueous-extract-with-the-concentration-of-2-mg/mL-or-4-mg/mL-on-the-growth-of-A549-cel-s-al-improved-(P<0.005).-The-combination-of-Huaier-aqueous-extract-and-DDP-and-the-combination-of-Huaier-aqueous-extract-with-rh-Endostatin-and-DDP-can-improve-the-inhibition-on-the-growth-of-A549-cel-s-(P<0.005).-Conclusion:Huaier-aqueous-extract-has-the-inhibition-and-apoptosis-inducing-ef-ects-on-the-A549-cel-s.-And-the-combination-of-Huaier-aqueous-extract-and-rh-Endostatin-or-DDP-has-the-synergistic-ef-ects-on-the-inhibition-of-A549-cel-s.-The-combination-of-Huaier-aqueous-extract-with-rh-Endostatin-and-DDP-has-the-synergistic-ef-ects-on-the-inhibition-of-A549-cel-s.-Huaier-aqueous-extract-can-reverse-the-cisplatin-resistance-in-human-lung-adenocarcinoma-A549/DDP-cel-s.

  12. Mechanism of chitosan adsorption on silica from aqueous solutions.

    Science.gov (United States)

    Tiraferri, Alberto; Maroni, Plinio; Rodríguez, Diana Caro; Borkovec, Michal

    2014-05-06

    We present a study of the adsorption of chitosan on silica. The adsorption behavior and the resulting layer properties are investigated by combining optical reflectometry and the quartz crystal microbalance. Exactly the same surfaces are used to measure the amount of adsorbed chitosan with both techniques, allowing the systematic combination of the respective experimental results. This experimental protocol makes it possible to accurately determine the thickness of the layers and their water content for chitosan adsorbed on silica from aqueous solutions of varying composition. In particular, we study the effect of pH in 10 mM NaCl, and we focus on the influence of electrolyte type and concentration for two representative pH conditions. Adsorbed layers are stable, and their properties are directly dependent on the behavior of chitosan in solution. In mildly acidic solutions, chitosan behaves like a weakly charged polyelectrolyte, whereby electrostatic attraction is the main driving force for adsorption. Under these conditions, chitosan forms rigid and thin adsorption monolayers with an average thickness of approximately 0.5 nm and a water content of roughly 60%. In neutral solutions, on the other hand, chitosan forms large aggregates, and thus adsorption layers are significantly thicker (∼10 nm) as well as dissipative, resulting in a large maximum of adsorbed mass around the pK of chitosan. These films are also characterized by a substantial amount of water, up to 95% of their total mass. Our results imply the possibility to produce adsorption layers with tailored properties simply by adjusting the solution chemistry during adsorption.

  13. Humic acid removal from aqueous solutions by peroxielectrocoagulation process

    Directory of Open Access Journals (Sweden)

    Ahmad Reza Yazdanbakhsh

    2015-06-01

    Full Text Available Background: Natural organic matter is the cause of many problems associated with water treatment such as the presence of disinfection by-products (DBPs and membrane fouling during water filtration. In this study, the performance of the peroxi-electrocoagulation process (PEP was investigated for the removal of humic acids (HAs from aqueous solutions. Methods: PEP was carried out for the removal of HA using a plexiglas reactor with a volume of 2 L and fitted with iron electrodes and a direct current supply (DC. Samples were taken at various amounts of pH (2-4, current density (1 and 2A/cm2, hydrogen peroxide (50-150 mg/L and reaction time (5-20 minutes and then filtered to remove sludge formed during reaction. Finally, the HA concentration was measured by UV absorbance at 254 nm (UV254. Results: Results indicated that increasing the concentration of H2O2 from 50 to 150 mg/L increased HA removal efficiency from 83% to 94.5%. The highest removal efficiency was observed at pH 3.0; by increasing the pH to the alkaline range, the efficiency of the process was reduced. It was found that HA removal efficiency was high in current density 1A/cm2. Increasing current density up to 1 A cm-2 caused a decrease in removal efficiency. Results of this study showed that under the optimum operating range for the process ([current density] = 1A/cm2, [hydrogen peroxide concentration] = 150 mg/L, [reaction time]= 20 minutes and [pH]= 3.0, HA removal efficiency reached 98%. Conclusion: It can be concluded that PEP has the potential to be utilized for cost-effective removal of HA from aqueous solutions.

  14. Removal of zirconium from aqueous solution by modified clinoptilolite

    Energy Technology Data Exchange (ETDEWEB)

    Faghihian, H., E-mail: h.faghih@sci.ui.ac.ir [Department of Chemistry, University of Isfahan, 81746-73441, Isfahan (Iran, Islamic Republic of); Kabiri-Tadi, M. [Department of Chemistry, University of Isfahan, 81746-73441, Isfahan (Iran, Islamic Republic of)

    2010-06-15

    Adsorptive behavior of natural clinoptilolite was assessed for the removal of zirconium from aqueous solutions. Natural zeolite was characterized by X-ray diffraction, X-ray fluorescence, thermal methods of analysis and FTIR. The zeolite sample composed mainly of clinoptilolite and presented a cation exchange capacity of 1.46 meq g{sup -1}. K, Na and Ca-exchanged forms of zeolite were prepared and their sorption capacities for removal of zirconium from aqueous solutions were determined. The effects of relevant parameters, including initial concentration, contact time, temperature and initial pH on the removal efficiency were investigated in batch studies. The pH strongly influenced zirconium adsorption capacity and maximal capacity was obtained at pH 1.0. The maximum removal efficiency obtained at 40 deg. C and equilibration time of 24 h on the Ca-exchanged form. Kinetics and isotherm of adsorption were also studied. The pseudo-first-order, pseudo-second-order, Elovich and intra-particle diffusion models were used to describe the kinetic data. The pseudo-second-order kinetic model provided excellent kinetic data fitting (R{sup 2} > 0.998) with rate constant of 1.60 x 10{sup -1}, 1.96 x 10{sup -1}, 2.45 x 10{sup -1} and 2.02 x 10{sup -1} g mmol{sup -1} min{sup -1} respectively for Na, K, Ca-exchanged forms and natural clinoptilolite. The Langmuir and Freundlich models were applied to describe the equilibrium isotherms for zirconium uptake and the Langmuir model agrees very well with experimental data. Thermodynamic parameters were determined and are discussed.

  15. Cations bind only weakly to amides in aqueous solutions.

    Science.gov (United States)

    Okur, Halil I; Kherb, Jaibir; Cremer, Paul S

    2013-04-01

    We investigated salt interactions with butyramide as a simple mimic of cation interactions with protein backbones. The experiments were performed in aqueous metal chloride solutions using two spectroscopic techniques. In the first, which provided information about contact pair formation, the response of the amide I band to the nature and concentration of salt was monitored in bulk aqueous solutions via attenuated total reflection Fourier transform infrared spectroscopy. It was found that molar concentrations of well-hydrated metal cations (Ca(2+), Mg(2+), Li(+)) led to the rise of a peak assigned to metal cation-bound amides (1645 cm(-1)) and a decrease in the peak associated with purely water-bound amides (1620 cm(-1)). In a complementary set of experiments, the effect of cation identity and concentration was investigated at the air/butyramide/water interface via vibrational sum frequency spectroscopy. In these studies, metal ion-amide binding led to the ordering of the adjacent water layer. Such experiments were sensitive to the interfacial partitioning of cations in either a contact pair with the amide or as a solvent separated pair. In both experiments, the ordering of the interactions of the cations was: Ca(2+) > Mg(2+) > Li(+) > Na(+) ≈ K(+). This is a direct cationic Hofmeister series. Even for Ca(2+), however, the apparent equilibrium dissociation constant of the cation with the amide carbonyl oxygen was no tighter than ∼8.5 M. For Na(+) and K(+), no evidence was found for any binding. As such, the interactions of metal cations with amides are far weaker than the analogous binding of weakly hydrated anions.

  16. Safety and antidiarrheal activity of Priva adhaerens aqueous leaf extract in a murine model

    Science.gov (United States)

    Nansunga, Miriam; Barasa, Ambrose; Abimana, Justus; Alele, Paul E.; Kasolo, Josephine

    2014-01-01

    Ethnopharmacological relevance Priva adhaerens (Forssk.) Chiov., a wildly growing plant, is reported in central Uganda to be an effective traditional remedy for diarrhea. The objective of this study was to provide a scientific basis for the ethnopharmacological utility of this plant whose aqueous leaf and shoot extract was evaluated for acute toxicity and antidiarrheal activity using a murine model. Materials and methods Acute toxicity of the aqueous leaf and shoot extract was assessed after determining the major phytochemicals present in the extract. The aqueous leaf and shoot extract was assayed against castor oil-induced diarrhea, transit time, and enteropooling, in comparison to loperamide, a standard drug. Results The oral LD50 value obtained for Priva adhaerens aqueous extract was greater than 5000 mg/kg in rats; the aqueous leaf and shoot extract possessed several important phytochemicals. Furthermore, the aqueous extract significantly, and dose-dependently, reduced frequency of stooling in castor oil-induced diarrhea, intestinal motility, and castor oil-induced enteropooling in rats. Conclusion This murine model shows that it is relatively safe to orally use the aqueous leaf and shoot extract of Priva adhaerens . The aqueous extract contains phytochemicals that are active for the treatment of diarrhea in a rat model. PMID:25304198

  17. Extraction of copper from bacterial leach solution using LIX98

    Institute of Scientific and Technical Information of China (English)

    柳建设; 邱冠周; 葛玉卿; 徐竞

    2002-01-01

    Extraction of copper from bacterial leach solution using Lix984 had been performed.It was found that the main factors influencing extraction yield of copper are the phase ratio and the concentration of extractant,following the pH of solution and extraction time and the order of factors influencing the separation rate is the pH of solution,the concentration of extractant,the extraction time and the phase ratio.The best conditions obtained by the orthogonal tests are as follows: the extractant concentration 4%,extraction time 3 min,phase ratio 1∶1,pH of solution 2.

  18. Adsorption of cesium on cement mortar from aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Volchek, Konstantin, E-mail: konstantin.volchek@ec.gc.ca [Emergencies Science and Technology Section, Environment Canada, 335 River Road, Ottawa, Ontario, Canada K1A 0H3 (Canada); Miah, Muhammed Yusuf [Emergencies Science and Technology Section, Environment Canada, 335 River Road, Ottawa, Ontario, Canada K1A 0H3 (Canada); Department of Applied Chemistry and Chemical Technology, Noakhali Science and Technology University (Bangladesh); Kuang, Wenxing; DeMaleki, Zack [Emergencies Science and Technology Section, Environment Canada, 335 River Road, Ottawa, Ontario, Canada K1A 0H3 (Canada); Tezel, F. Handan [Department of Chemical and Biological Engineering, University of Ottawa, 161 Louis-Pasteur, Ottawa, Ontario, Canada K1N 6N5 (Canada)

    2011-10-30

    Highlights: {yields} The adsorption of cesium on cement mortar was investigated in a range of temperatures and cesium concentrations. {yields} The pseudo-second order kinetic model produced a good fit with the experimental kinetic data. {yields} Equilibrium test results correlated well with the Freundlich isotherm adsorption model. {yields} The interaction between cesium ions and cement mortar was dominated by chemical adsorption. - Abstract: The adsorption of cesium on cement mortar from aqueous solutions was studied in series of bench-scale tests. The effects of cesium concentration, temperature and contact time on process kinetics and equilibrium were evaluated. Experiments were carried out in a range of initial cesium concentrations from 0.0103 to 10.88 mg L{sup -1} and temperatures from 278 to 313 K using coupons of cement mortar immersed in the solutions. Non-radioactive cesium chloride was used as a surrogate of the radioactive {sup 137}Cs. Solution samples were taken after set periods of time and analyzed by inductively coupled plasma mass spectroscopy. Depending on the initial cesium concentration, its equilibrium concentration in solution ranged from 0.0069 to 8.837 mg L{sup -1} while the respective surface concentration on coupons varied from 0.0395 to 22.34 {mu}g cm{sup -2}. Equilibrium test results correlated well with the Freundlich isotherm model for the entire test duration. Test results revealed that an increase in temperature resulted in an increase in adsorption rate and a decrease in equilibrium cesium surface concentration. Among several kinetic models considered, the pseudo-second order reaction model was found to be the best to describe the kinetic test results in the studied range of concentrations. The adsorption activation energy determined from Arrhenius equation was found to be approximately 55.9 kJ mol{sup -1} suggesting that chemisorption was the prevalent mechanism of interaction between cesium ions and cement mortar.

  19. Antiulcer activity of aqueous and ethanolic extracts of Ocimum sanctum leaves in albino rats

    Directory of Open Access Journals (Sweden)

    Sowmya Kaniganti

    2016-08-01

    Conclusions: Both the doses of aqueous and ethanolic extracts of Ocimum sanctum leaves exhibited significant antiulcer activity in pyloric ligation model, whereas only 200 mg/kg of aqueous leaf extract was effective in cold restrain stress model. [Int J Basic Clin Pharmacol 2016; 5(4.000: 1353-1358

  20. In-vitro anti- inflammatory activity of aqueous extract of leaves of Plectranthus amboinicus (Lour.) Spreng.

    Science.gov (United States)

    Ravikumar, V R; Dhanamani, M; Sudhamani, T

    2009-04-01

    Aqueous extract of leaves of Plectranthus amboinicus (lour.) Spreng, which is traditionally used in the treatment of cough and cold was screened for its anti- inflammatory activity by HRBC membrane stabilisation model. Aqueous extract (500 mcg/ml) showed significant anti-inflammatory activity as compared to that of hydrocortisone sodium.

  1. In-vitro anti- inflammatory activity of aqueous extract of leaves of Plectranthus amboinicus (Lour.) Spreng

    OpenAIRE

    Ravikumar, V.R.; Dhanamani, M.; Sudhamani, T.

    2009-01-01

    Aqueous extract of leaves of Plectranthus amboinicus (lour.) Spreng, which is traditionally used in the treatment of cough and cold was screened for its anti- inflammatory activity by HRBC membrane stabilisation model. Aqueous extract (500 mcg/ml) showed significant anti-inflammatory activity as compared to that of hydrocortisone sodium.

  2. Bactericidal Action of Photo-Irradiated Aqueous Extracts from the Residue of Crushed Grapes from Winemaking.

    Science.gov (United States)

    Tsukada, Mana; Sheng, Hong; Tada, Mika; Mokudai, Takayuki; Oizumi, Satomi; Kamachi, Toshiaki; Niwano, Yoshimi

    2016-01-01

    Our previous studies revealed that photo-irradiation of polyphenols could exert bactericidal action via reactive oxygen species (ROS). In the present study, the photo-irradiation-induced bactericidal activity of the aqueous extract from the residue of crushed grapes from winemaking was investigated in relation to ROS formation. Staphylococcus aureus suspended in the extract was irradiated with LED light at 400 nm. This solution killed the bacteria, and a 3-4 log and a >5-log reduction of the viable counts were observed within 10 and 20 min, respectively. LED light irradiation alone also killed the bacteria, but the viable counts were 2-4 log higher than those of the photo-irradiated extract. In contrast, almost no change occurred in the suspension without LED irradiation. When hydroxyl radical scavengers were added to the suspension, the bactericidal effect of the photo-irradiated extract was attenuated. Furthermore, electron spin resonance analysis demonstrated that hydroxyl radicals were generated by the photo-irradiation of the extract. The present study suggests that polyphenolic compounds in the extract exert bactericidal activity via hydroxyl radical formation upon photo-irradiation.

  3. Lead removal from aqueous solutions by a Tunisian smectitic clay.

    Science.gov (United States)

    Chaari, Islem; Fakhfakh, Emna; Chakroun, Salima; Bouzid, Jalel; Boujelben, Nesrine; Feki, Mongi; Rocha, Fernando; Jamoussi, Fakher

    2008-08-15

    The adsorption of Pb(2+) ions onto Tunisian smectite-rich clay in aqueous solution was studied in a batch system. Four samples of clay (AYD, AYDh, AYDs, AYDc) were used. The raw AYD clay was sampled in the Coniacian-Early Campanian of Jebel Aïdoudi in El Hamma area (South of Tunisia). AYDh and AYDs corresponds to AYD activated by 2.5 mol/l hydrochloric acid and 2.5 mol/l sulphuric acid, respectively. AYDc corresponds to AYD calcined at different temperatures (100, 200, 300, 400, 500 and 600 degrees C). The raw AYD clay was characterized by X-ray diffraction, chemical analysis, infrared spectroscopy and coupled DTA-TGA. Specific surface area of all the clay samples was determined from nitrogen adsorption isotherms. Preliminary adsorption tests showed that sulphuric acid and hydrochloric acid activation of raw AYD clay enhanced its adsorption capacity for Pb(2+) ions. However, the uptake of Pb(2+) by AYDs was very high compared to that by AYDh. This fact was attributed to the greater solubility of clay minerals in sulphuric acid compared to hydrochloric acid. Thermic activation of AYD clay reduced the Pb(2+) uptake as soon as calcination temperature reaches 200 degrees C. All these preliminary results were well correlated to the variation of the specific surface area of the clay samples. The ability of AYDs sample to remove Pb(2+) from aqueous solutions has been studied at different operating conditions: contact time, adsorbent amount, metal ion concentration and pH. Kinetic experiments showed that the sorption of lead ions on AYDs was very fast and the equilibrium was practically reached after only 20 min. The results revealed also that the adsorption of lead increases with an increase in the solution pH from 1 to 4.5 and then decreases, slightly between pH 4.5 and 6, and rapidly at pH 6.5 due to the precipitation of some Pb(2+) ions. The equilibrium data were analysed using Langmuir isotherm model. The maximum adsorption capacity (Q(0)) increased from 25 to 25

  4. Gamma Radiolysis Studies of Aqueous Solution of Brilliant Green Dye

    Directory of Open Access Journals (Sweden)

    D. V. Parwate

    2011-01-01

    Full Text Available The effect of γ–radiation on colour intensity of aqueous solution of Brilliant Green has been investigated at two different concentrations. The degradation of Brilliant Green (BG has also been investigated in presence of suspended ZnO, by adding different amounts of ZnO. Simultaneously the conductance and pH of each solution system were measured before and after γ-irradiation. All the γ–irradiations were performed at a dose rate of 0.60 kGyhr-1 in GC-900. The maximum dose required for the complete degradation of the dye was found to be 0.39 kGy. G(-dye values were found to decrease with increase in gamma dose and were in the range 4.26 - 12.81. The conductance (7.6 - 25.3 μS and pH values increased marginally with dose for both the concentrations. The rate of decolouration was found to be high at lower doses and the efficiency of dye removal was higher at low concentration of the dye. This may be attributed to the presence of reaction by-products from the destruction of parent compound build up and compete for reaction intermediate species. The rate of reaction and rate constants were calculated and it was found that the degradation reaction follows first order kinetics. It was found that the decolouration percentage was more in dye systems in absence of ZnO.

  5. Removal of Nitrate From Aqueous Solution Using Rice Chaff

    Directory of Open Access Journals (Sweden)

    Dehghani

    2015-09-01

    Full Text Available Background Nitrate is largely dissolved in the surface and ground water, due to its high solubility. Continual uptake of nitrite through drinking water can lead to problems and diseases (such as blue baby for humans, especially children. Objectives The aim of this study was to develop a new and inexpensive method for the removal of nitrate from water. In this regard, the possibility of using chaff for removal of nitrate from aqueous solutions was studied and the optimum operating conditions of nitrate removal was determined. Materials and Methods This is a cross-sectional study conducted in laboratory scale. The UV spectrophotometer at a wavelength of maximum absorbance (220 nm was used to determine the nitrate concentration. The effect of pH, amount of chaff, temperature, and contact time were investigated. Results The result of this study revealed that chaff as an absorbent could remove nitrate from solutions, and the efficiency of adsorption increased as contact time increased from 5 to 30 minutes, amount of chaff increased from 1 to 3 g, temperature increased in a range of 300 - 400°C and the amount of pH decreased from 10 to 3. The maximum adsorption rate was around pH 3 (53.14%. Conclusions It was shown that the removal efficiency of nitrate was directly proportional to the amount of chaff, temperature, and contact time but inversely to the pH. This study showed that nitrate removal by chaff is a promising technique.

  6. Structure and phase behavior of aqueous methylcellulose solutions

    Science.gov (United States)

    McAllister, John; Schmidt, Peter; Lodge, Timothy; Bates, Frank

    2015-03-01

    Cellulose ethers (CE) constitute a multi-billion dollar industry, and have found end uses in a broad array of applications from construction materials, food products, personal care products, and pharmaceuticals for more than 80 years. Methylcellulose (MC, with the trade name METHOCEL™) is a CE in which there is a partial substitution of -OH groups with -OCH3 groups. This results in a polymer that is water-soluble at low temperatures, and aqueous solutions of MC display gelation and phase separation at higher temperatures. The nature of MC gelation has been debated for many years, and this project has made significant advances in the understanding of the solution properties of CEs. We have characterized a fibrillar structure of MC gels by cryogenic transmission electron microscopy (cryo-TEM) and small angle neutron scattering (SANS). Using light scattering, turbidity measurements, and dynamic mechanical spectroscopy (DMS) we report that MC microphase separates by nucleation and growth of fibril aggregates, and is a different process from LCST phase separation.

  7. Single Molecule Electrochemical Detection in Aqueous Solutions and Ionic Liquids.

    Science.gov (United States)

    Byers, Joshua C; Paulose Nadappuram, Binoy; Perry, David; McKelvey, Kim; Colburn, Alex W; Unwin, Patrick R

    2015-10-20

    Single molecule electrochemical detection (SMED) is an extremely challenging aspect of electroanalytical chemistry, requiring unconventional electrochemical cells and measurements. Here, SMED is reported using a "quad-probe" (four-channel probe) pipet cell, fabricated by depositing carbon pyrolytically into two diagonally opposite barrels of a laser-pulled quartz quadruple-barreled pipet and filling the open channels with electrolyte solution, and quasi-reference counter electrodes. A meniscus forms at the end of the probe covering the two working electrodes and is brought into contact with a substrate working electrode surface. In this way, a nanogap cell is produced whereby the two carbon electrodes in the pipet can be used to promote redox cycling of an individual molecule with the substrate. Anticorrelated currents generated at the substrate and tip electrodes, at particular distances (typically tens of nanometers), are consistent with the detection of single molecules. The low background noise realized in this droplet format opens up new opportunities in single molecule electrochemistry, including the use of ionic liquids, as well as aqueous solution, and the quantitative assessment and analysis of factors influencing redox cycling currents, due to a precisely known gap size.

  8. Drop-on-demand for aqueous solutions of sodium alginate

    Science.gov (United States)

    Herran, C. Leigh; Coutris, Nicole

    2013-06-01

    Inkjet printing is a rapidly growing commercial process for applications that depend on precisely patterning micro-scale droplets. These applications increasingly require complex fluids, introducing viscoelastic properties which play an important role in droplet formation. The objective of this study is to determine how to obtain single, uniform and spherical ("successful") droplets from aqueous solutions of sodium alginate with a piezoelectric drop-on-demand printing method. In order to control the volume and velocities of droplets, the effect on the droplet formation of the characteristics of the waveform such as voltage amplitude and dwell time is studied. The results depend also on the fluid rheology. The viscosity of the chosen fluid is a function of the concentration, as the viscoelastic properties increase at higher concentration. In this paper, the droplet formation process is characterized in terms of both the waveform and the rheological properties of the solution. The characterization of the fluids and waveform will be pursued first and the droplet formation and its control will be studied. Finally, the results will be presented with a map in ranges of the Ohnesorge, Deborah and Weber numbers.

  9. Columnar molecular aggregation in the aqueous solutions of disodium cromoglycate

    Science.gov (United States)

    Agra-Kooijman, Dena M.; Singh, Gautam; Lorenz, Alexander; Collings, Peter J.; Kitzerow, Heinz-S.; Kumar, Satyendra

    2014-06-01

    Stack, chimneylike, and threadlike assemblies have previously been proposed for the structure of disodium cromoglycate (DSCG) aggregates in aqueous solutions. The results of the synchrotron x-ray scattering investigations reported here reveal the formation of simple columnar assemblies with π-π stacking at a separation of 3.4 Å between the DSCG molecules. Lateral separation between the assemblies is concentration and temperature dependent, varying from ˜35 to 42 Å in the orientationally ordered nematic (N) phase and from 27 to 32 Å in the columnar or middle (M) phase having long range lateral positional order. The assemblies' length depends on concentration and consists of ˜23 molecules in the N phase, becoming three to ten times larger in the M phase. The scission energy is concentration dependent in the N phase with values ˜7.19 ± 0.14 kBT (15 wt %), 2.73 ± 0.4 kBT (20 wt %), and 3.05 ± 0.2 kBT (25 wt %). Solutions of all concentrations undergo a spinodal decomposition at temperatures above ˜40 °C, resulting in DSCG-rich regions with the M phase and water-rich regions in the N and isotropic phases.

  10. Corrosion of metastable iron alloys in aqueous solutions

    Science.gov (United States)

    Wolf, Gerhard K.; Ferber, H.

    1983-05-01

    There exist some examples showing that metastable surface alloys can modify the corrision properties of a substrate in the same way as stable alloys do. In the present paper the corrosion behaviour of metastable surface alloys obtained by implanting gold, lead and mercury in iron was studied in aqueous solution of pH = 5.6. Potentiodynamic current density-potential curves were recorded of the implanted samples without further treatment and after isothermal annealing to temperatures up to 800°C. The results were compared with structural information on the alloys obtained by Turos et al. with α-backscattering and channeling experiments. Gold implantation turned out to enhance the active corrosion rate of iron, while lead and mercury had an impeding effect. The annealing experiments showed that the surface alloying facilitated the passivation of iron as long as the substitutional solid solution was "(meta)stable". After the breakdown at higher annealing temperatures leading to surface migration and clustering of the implanted elements a significant increase of the critical current density for passivation took place. This indicates passivation difficulties caused by the heterogeneous distribution of the "alloying" particles. In general the results suggest that substitutional metastable iron alloys cause in a systematic way corrosion inhibition or enhancement. However, their corrosion properties may change completely for non-substitutional distribution of the alloying elements as originating from annealing at higher temperatures.

  11. Cast iron deterioration with time in various aqueous salt solutions

    Indian Academy of Sciences (India)

    Rita Mehra; Aditi Soni

    2002-02-01

    The changes with time in the corrosion rate and corrosion current density on a cast iron electrode in various aqueous salt solutions have been carried out using total immersion test and potentiostatic polarization curves. The concentration of salts taken is expected to be present in potable water. The relative behaviour of these salts towards corrosion has also been studied, which is found to be different from previous studies. The total immersion test parameters viz. weight loss, corrosion rate as well as potentiostatic parameters, open circuit potential, corr, Tafel slopes, corrosion rate, have been calculated by standard methods. Besides these the relative increase in corrosion rate with time as well as the percentage to which corrosion rate should be decreased so as to provide protection towards corrosion have also been calculated. It was found that KCl and NaCl are major contributors than MnSO4, Pb(NO3)2, KI and KBr. The relative increase in corrosion is high in KBr, KI, NaNO3, CaCl2, and less in Pb(NO3)2, NaHCO3 and CaCO3 test solutions. For the reliability of results the data has been statistically analysed.

  12. Enrichment of surfactant from its aqueous solution using ultrasonic atomization.

    Science.gov (United States)

    Takaya, Haruko; Nii, Susumu; Kawaizumi, Fumio; Takahashi, Katsuroku

    2005-08-01

    Dilute aqueous solutions of dodecyl-benzenesulfonic acid sodium salt (DBS-Na) and polyoxyethylenenonylphenyl ethers (PONPEs) were ultrasonically atomized. The surfactants were concentrated in collected mist droplets. The enrichment ratio increased with decreasing surfactant concentration. Depending on the surfactant's molecular weight and affinity to water, different enrichment ratio was observed in the range of low feed concentrations. For anionic surfactant, DBS-Na, the enrichment ratio was significantly improved by KCl addition and a peak appeared on the plot of the ratio against KCl concentration. Addition of NaCl or CaCl2 . 2H2O to the surfactant solution also enhanced the enrichment ratio; however, the effect was relatively small. Such behaviors of the ratio were interpreted as enhanced interfacial adsorption of the surfactant and a lack of supply of surfactant monomers from liquid bulk because of slow breaking of surfactant micelles. Time required for collecting an amount of mist was also observed. Among the three salt systems, the time for KCl system was twice as long as others. This fact suggested that the formation of smaller droplets in KCl system.

  13. Metal ion removal from aqueous solution using physic seed hull.

    Science.gov (United States)

    Mohammad, Masita; Maitra, Saikat; Ahmad, Naveed; Bustam, Azmi; Sen, T K; Dutta, Binay K

    2010-07-15

    The potential of physic seed hull (PSH), Jantropha curcas L. as an adsorbent for the removal of Cd(2+) and Zn(2+) metal ions from aqueous solution has been investigated. It has been found that the amount of adsorption for both Cd(2+) and Zn(2+) increased with the increase in initial metal ions concentration, contact time, temperature, adsorbent dosage and the solution pH (in acidic range), but decreased with the increase in the particle size of the adsorbent. The adsorption process for both metal ions on PSH consists of three stages-a rapid initial adsorption followed by a period of slower uptake of metal ions and virtually no uptake at the final stage. The kinetics of metal ions adsorption on PSH followed a pseudo-second-order model. The adsorption equilibrium data were fitted in the three adsorption isotherms-Freundlich, Langmuir and Dubinin-Radushkevich isotherms. The data best fit in the Langmuir isotherm indication monolayer chemisorption of the metal ions. The adsorption capacity of PSH for both Zn(2+) and Cd(2+) was found to be comparable with other available adsorbents. About 36-47% of the adsorbed metal could be leached out of the loaded PSH using 0.1M HCl as the eluting medium.

  14. Adsorption of itaconic acid from aqueous solutions onto alumina

    Directory of Open Access Journals (Sweden)

    JELENA J. GULICOVSKI

    2008-08-01

    Full Text Available Itaconic acid, IA (C5H6O4, was investigated as a potential flocculant for the aqueous processing of alumina powders. The adsorption of IA, as a function of its concentration and pH value of the solution, onto the alumina surface was studied by the solution depletion method. The stability of the suspensions in the presence of itaconic acid was evaluated in light of the surface charge of the alumina powder used, the degree of dissociation of IA, as well as the sedimentation behavior and rheology of the suspensions. It was found that the adsorption process is extremely pH dependent; the maximum adsorption of IA onto alumina surface occurring at a pH close to the value of the first IA dissociation constant, pKa1. Also, IA does not influence the value of the point of zero charge of alumina. It was shown that IA represents an efficient flocculant for concentrated acidic alumina suspensions.

  15. Decomposition of 2-mercaptothiazoline in aqueous solution by ozonation.

    Science.gov (United States)

    Chen, Y H; Chang, C Y; Chen, C C; Chiu, C Y; Yu, Y H; Chiang, P C; Ku, Y; Chen, J N; Chang, C F

    2004-07-01

    This study investigates the ozonation of 2-mercaptothiazoline (2-MT). The 2-MT is one of the important organic additives for the electroplating solution of the printed wiring board industry and has been widely used as a corrosion inhibitor in many industrial processes. It is of concern for the aquatic pollution control especially in the wastewaters. Semibatch ozonation experiments in the completely stirred tank reactor are performed under various concentrations of input ozone. The concentrations of 2-MT, sulfate, and ammonium are analyzed at specified time intervals to elucidate the decomposition of 2-MT during the ozonation. In addition, the time variation of the dissolved ozone concentration (C(ALb)) is continuously monitored in the course of experiments. Total organic carbon (TOC) is chosen and measured as a mineralization index of the ozonation of 2-MT. The results indicate that the decomposition of 2-MT is efficient, while the mineralization of TOC is limited via the ozonation only. Simultaneously, the yield of sulfate with the maximum value of about 47% is characterized by the increases of TOC removal and ozone consumption. These results can provide some useful information for assessing the feasibility of the treatment of 2-MT in the aqueous solution by the ozonation.

  16. Separation of Indium and Iron from Dilute Sulphate Solutions with a Phosphorous Mixer Extractant

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The phosphorous mixer introduced could replace D2EHPA as an extractant applied in the extraction of indium. The extraction properties of the phosphorous mixer were studied. The influences of extractant concentration, organic/aqueous (O/A) phase ratio, equilibrium time, and pH value of the feed solutions on the extraction of indium and separation of indium-iron were investigated experimentally. Under the best operating conditions, more than 98% of indium was extracted through two-stage counter-current extraction. The optimizing condition of indium extraction is determined as follows: O/A = 1∶(9€?2) in volume ratio; 30% PPD in sulphonated kerosene; pH of the feed, about 0.6; equilibrium time, 3€? min. The extractant has good reusing and anti-aging properties.

  17. Extraction studies of cobalt (Ⅱ) and nickel (Ⅱ) from chloride solution using PC88A

    Institute of Scientific and Technical Information of China (English)

    LUO Lin; WEI Jian-hong; WU Gen-yi; F. TOYOHISA; S. ATSUSHI

    2006-01-01

    Solvent extraction study of cobalt and nickel were carried out from a chloride solution with a high ratio of Co to Ni using the sodium salt of PC88A as extractant diluted in kerosene. The solution was generated in batches by leaching a tungsten super alloy scraps. The results show that extraction rate of metal ions increases with increase of aqueous phase pH value. The pH0.5 value difference of 1.40 with PC88A indicates the possible separation of cobalt and nickel. Increase of the concentration of the solvent can enhance the percentage extraction of both metal ions. Improvement of temperature is beneficial to extraction separation of cobalt and nickel. Extraction and stripping processes were also studied in a cross-current solvent extraction unit and the results were also given.

  18. Solvent extraction-separation of La(III), Eu(III) and Er(III) ions from aqueous chloride medium using carbamoyl-carboxylic acid extractants

    Institute of Scientific and Technical Information of China (English)

    Reyhaneh Safarbali; Mohammad Reza Yaftian; Abbasali Zamani

    2016-01-01

    N,N-dibutyldiglycol amic acid (HLI) and N,N-dioctyldiglycol amic acid (HLI) were synthesized and characterized by con-ventional spectroscopic methods. These molecules were examined as extractants for extraction-separation of La(III), Eu(III) and Er(III), as representative ions of light, middle and heavy rare earths, from aqueous chloride solutions. The analysis of the extraction equilibria revealed that the extracted species of lanthanum and europium ions by both of the extractants had a 1:3 metal to ligand ratio. It was suggested that erbium ions were extracted into the organic phase via the formation of Er(LI or I)2Cl complexes. The effect of the organic diluents on the extraction-separation efficiency of the studied rare earths by HLI and HLI was investigated by comparing the results obtained in dichloromethane and carbon tetrachloride. Regardless to the diluent used, the order of selectivity presented by the investigated extractants was Er(III)>Eu(III)>La(III). It is noteworthy that, a significant enhancement in separation of the studied rare earths by the extractants was achieved in their competitive extraction experiments with respect to that obtained in single component extraction experiments. Applicability of the extractants for the removal of rare earth ions from spent Ni-MH batteries was tested by removal of La(III), Eu(III) and Er(III) ions from simulated leach solution of such batteries.

  19. Green synthesis of silver nanoparticles using cranberry powder aqueous extract: characterization and antimicrobial properties

    Directory of Open Access Journals (Sweden)

    Ashour AA

    2015-12-01

    Full Text Available Asmaa A Ashour,1 Dina Raafat,2 Hanan M El-Gowelli,3 Amal H El-Kamel1 1Department of Pharmaceutics, 2Department of Pharmaceutical Microbiology, 3Department of Pharmacology and Toxicology, Faculty of Pharmacy, Alexandria University, Alexandria, Egypt Background: The growing threat of microbial resistance against traditional antibiotics has prompted the development of several antimicrobial nanoparticles (NPs, including silver NPs (AgNPs. In this article, a simple and eco-friendly method for the synthesis of AgNPs using the cranberry powder aqueous extract is reported.Materials and methods: Cranberry powder aqueous extracts (0.2%, 0.5%, and 0.8% w/v were allowed to interact for 24 hours with a silver nitrate solution (10 mM at 30°C at a ratio of 1:10. The formation of AgNPs was confirmed by ultraviolet-visible spectroscopy and their concentrations were determined using atomic absorption spectroscopy. The prepared NPs were evaluated by transmission electron microscopy, measurement of ζ-potential, and Fourier-transform infrared spectroscopy. The in vitro antimicrobial properties of AgNPs were then investigated against several microbial strains. Finally, in vivo appraisal of both wound-healing and antimicrobial properties of either plain AgNPs (prepared using 0.2% extract or AgNP-Pluronic F-127 gel was conducted in a rat model after induction of a Staphylococcus aureus ATCC 6538P wound infection.Results: The formation of AgNPs was confirmed by ultraviolet-visible spectroscopy, where a surface-plasmon resonance absorption peak was observed between 432 and 438 nm. Both size and concentration of the formed AgNPs increased with increasing concentration of the extracts. The developed NPs were stable, almost spherical, and polydisperse, with a size range of 1.4–8.6 nm. The negative ζ-potential values, as well as Fourier-transform infrared spectroscopy analysis, indicated the presence of a capping agent adsorbed onto the surface of the particles. In

  20. Sonochemical degradation of martius yellow dye in aqueous solution.

    Science.gov (United States)

    Singla, Ritu; Grieser, Franz; Ashokkumar, Muthupandian

    2009-01-01

    The sonolytic degradation of the textile dye martius yellow, also known as either naphthol yellow or acid orange 24, was studied at various initial concentrations in water. The degradation of the dye followed first-order kinetics under the conditions examined. Based on gas chromatographic results and sonoluminescence measurements of sonicated aqueous solutions of the dye, it is concluded that pyrolysis does not play a significant role in its degradation. The chromatographic identification of hydroxy added species indicates that an OH radical induced reaction is the main degradation pathway of the dye. Considering the non-volatility and surface activity of the dye, the degradation of the dye most probably takes place at the bubble/solution interface. The quantitative and qualitative formation of the degradation intermediates and final products were monitored using HPLC and ESMS. The analytical results suggest that the sonolytic degradation of the dye proceeds via hydroxylation of the aryl ring and also by C-N bond cleavage of the chromophoric ring, either through OH radical attack or through another unidentified process. The identification of various intermediates and end products also imply that the degradation of martius yellow proceeds through multiple reaction pathways. Total organic carbon (TOC) analyses of the dye solutions at various times following sonication revealed that sonolysis was effective in the initial degradation of the parent dye but very slow in achieving mineralization. The slow rate of mineralization is likely to be due to the inability of many of the intermediate products such as, the carboxylic acids, to accumulate at the bubble (air/water) interface and undergo decomposition due to their high water solubility (low surface activity).

  1. Interaction of gypsum with lead in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Astilleros, J.M., E-mail: jmastill@geo.ucm.es [Dpto. Cristalografia y Mineralogia, Universidad Complutense de Madrid, Jose Antonio Novais, 2, E-28040 Madrid (Spain); Godelitsas, A. [Department of Mineralogy and Petrology, Faculty of Geology and Geoenvironment, University of Athens, Panepistimioupoli Zographou, 15784 Athens (Greece); Rodriguez-Blanco, J.D. [School of Earth and Environments, Faculty of Environment, University of Leeds, Leeds LS2 9JT (United Kingdom); Fernandez-Diaz, L. [Dpto. Cristalografia y Mineralogia, Universidad Complutense de Madrid, Jose Antonio Novais, 2, E-28040 Madrid (Spain); Prieto, M. [Dpto. de Geologia, Universidad de Oviedo, E-30005 Oviedo (Spain); Lagoyannis, A.; Harissopulos, S. [Tandem Accelerator Laboratory, Institute of Nuclear Physics, NCSR ' Demokritos' , GR-15310 Attiki (Greece)

    2010-07-15

    Sorption processes on mineral surfaces are a critical factor in controlling the distribution and accumulation of potentially harmful metals in the environment. This work investigates the effectiveness of gypsum (CaSO{sub 4}.2H{sub 2}O) to sequester Pb. The interaction of gypsum fragments with Pb-bearing solutions (10, 100 and 1000 mg/L) was monitored by performing macroscopic batch-type experiments conducted at room temperature. The aqueous phase composition was periodically determined by Atomic Absorption Spectrometry (AAS), Ion Chromatography (IC) and Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). Regardless of the [Pb{sub aq}]{sub initial}, a [Pb{sub aq}]{sub final} < 4 mg/L was always reached. The uptake process was fast (t < 1 h) for [Pb{sub aq}]{sub initial} {>=} 100 mg/L and significantly slower (t > 1 week) for [Pb{sub aq}]{sub initial} = 10 mg/L. Speciation calculations revealed that after a long time of interaction (1 month), all the solutions reached equilibrium with respect to both gypsum and anglesite. For [Pb{sub aq}]{sub initial} {>=} 100 mg/L, sorption takes place mainly via the rapid dissolution of gypsum and the simultaneous formation of anglesite both on the gypsum surface and in the bulk solution. In the case of [Pb{sub aq}]{sub initial} = 10 mg/L, no anglesite precipitation was observed, but surface spectroscopy (proton Rutherford Backscattering Spectroscopy, p-RBS) confirmed the formation of Pb-bearing surface layers on the (0 1 0) gypsum surface in this case also. This study shows that the surface of gypsum can play an important role in the attenuation of Pb in contaminated waters.

  2. The study of influence of the Teslar technology on aqueous solution of some biomolecules

    CERN Document Server

    Andreev, E; Krasnoholovets, V; 10.1155/2007/94286

    2012-01-01

    The possibility of recording physical changes in aqueos solutions caused by a unique field generated by the Teslar chip (TC) inside a quartz wristwatch has been studied using holographic interferometry. We show that the refraction index of degassed pure distilled water and aqueous solutions of L-tyrosine and b-alanine affected by the TC does not change during the first 10 minutes of influence. In contrast, a 1% aqueous solution of plasma extracted from the blood of a patient with heart-vascular disease changes the refractive index when affected by the TC. The characteristic time of reaction is about 100 s. Based on our prior research experience we state that the response of the system studied to the TC's field is similar to that stipulated by the action of a constant magnetic field with the intensity of 1.1 x 10^{-3} T. Nevertheless, our team could unambiguously prove that the TC generates the inerton field, which is associated with a substructure of the matter waves (and, therefore, it does not relate to the...

  3. The Study of Influence of the Teslar Technology on Aqueous Solution of Some Biomolecules

    Directory of Open Access Journals (Sweden)

    E. Andreev

    2007-01-01

    Full Text Available The possibility of recording physical changes in aqueos solutions caused by a unique field generated by the Teslar chip (TC inside a quartz wristwatch has been studied using holographic interferometry. We show that the refraction index of degassed pure distilled water and aqueous solutions of L-tyrosine and b-alanine affected by the TC does not change during the first 10 minutes of influence. In contrast, a 1% aqueous solution of plasma extracted from the blood of a patient with heart vascular disease changes the refractive index when affected by the TC. The characteristic time of reaction is about 102 seconds. Based on our prior research experience, we state that the response of the system studied to the TC's field is similar to that stipulated by the action of a constant magnetic field with the intensity of 1.1×10−3 T. Nevertheless, our team have unambiguously proved that the TC generates the inerton field, which is associated with a substructure of the matter waves (and, therefore, it does not relate to the electromagnetic nature. We could unambiguously prove that the TC generates the inerton field.

  4. Thin extractive membrane for monitoring actinides in aqueous streams.

    Science.gov (United States)

    Chavan, Vivek; Paul, Sumana; Pandey, Ashok K; Kalsi, P C; Goswami, A

    2013-09-15

    Alpha spectrometry and solid state nuclear track detectors (SSNTDs) are used for monitoring ultra-trace amount of alpha emitting actinides in different aqueous streams. However, these techniques have limitations i.e. alpha spectrometry requires a preconcentration step and SSNTDs are not chemically selective. Therefore, a thin polymer inclusion membrane (PIM) supported on silanized glass was developed for preconcentraion and determination of ultra-trace concentration of actinides by α-spectrometry and SSNTDs. PIMs were formed by spin coating on hydrophobic glass slide or solvent casting to form thin and self-supported membranes, respectively. Sorption experiments indicated that uptakes of actinides in the PIM were highly dependent on acidity of solution i.e. Am(III) sorbed up to 0.1 molL(-1) HNO₃, U(VI) up to 0.5 molL(-1) HNO₃ and Pu(IV) from HNO₃ concentration as high as 4 molL(-1). A scheme was developed for selective sorption of target actinide in the PIM by adjusting acidity and oxidation state of actinide. The actinides sorbed in PIMs were quantified by alpha spectrometry and SSNTDs. For SSNTDs, neutron induced fission-fragment tracks and α-particle tracks were registered in Garware polyester and CR-39 for quantifications of natural uranium and α-emitting actinides ((241)Am/(239)Pu/(233)U), respectively. Finally, the membranes were tested to quantify Pu in 4 molL(-1) HNO3 solutions and synthetic urine samples.

  5. Solvent extraction of radionuclides from aqueous tank waste

    Energy Technology Data Exchange (ETDEWEB)

    Bonnesen, P.; Sachleben, R.; Moyer, B. [Oak Ridge National Lab., TN (United States)

    1996-10-01

    The purpose of this task is to develop an efficient solvent-extraction and stripping process to remove the fission products {sup 99}Tc, {sup 90}Sr, and {sup 137}Cs from alkaline tank waste, such as those stored at Hanford and Oak Ridge. As such, this task expands on FY 1995`s successful development of a solvent-extraction and stripping process for technetium separation from alkaline tank-waste solutions. This process now includes the capability of removing both technetium and strontium simultaneously. In this form, the process has been named SRTALK and will be developed further in this program as a prelude to developing a system capable of removing technetium, strontium, and cesium.

  6. [Aqueous iodine solutions as disinfectants: composition, stability, comparison with chlorine and bromine solution (author's transl)].

    Science.gov (United States)

    Gottardi, W

    1978-09-01

    The equilibrium concentrations of aqueous iodine solutions in dependence of the total concentration and the pH-value have been calculated with and without regard of the iodate formation. The values obtained by the latter methode enabled by application of the known rate law to calculate the initial rate of the iodate formation and to draw from this conclusions concerning the stability of iodine solutions. On the grounds of these calculations to aqueous iodine solutions in the concentration and pH-range which is relevant for disinfection (greater than 10(-5) M/l, pH 6--9) one can attribute a stability sufficient for the use in practice and - unlike chlorine and bromine solutions - a content of bactericidal "free halogene" which is higher and independent of the pH-value. The disinfecting action of the iodine cation (H2O+J) which is supposed to be very powerful can be neglected because of its low concentration (10(-3)--10(-6%) of the total concentration). Hypoiodic acid which has already been converted into iodate by disproportionation is as good as lost for the disinfection because of the extremely slow reverse reaction.

  7. Improved phenol adsorption from aqueous solution using electrically conducting adsorbents

    Energy Technology Data Exchange (ETDEWEB)

    Asghar, Hafiz Muhammad Anwaar; Hussain, Syed Nadir [The University of Manchester, Manchester (United Kingdom); Sattar, Hamed [University of Leeds, Leeds (United Kingdom); Brown, Nigel Willis [Daresbury Innovation Centre, Cheshire (United Kingdom); Roberts, Edward Pelham Lindfield [University of Calgary, Calgary (Canada)

    2014-05-15

    The electrically conducting and partially porous graphite based adsorbent (called Nyex{sup TM} 2000) was tested for its adsorption capacity and electrochemical regeneration ability for the removal of phenol from aqueous solution. Nyex{sup TM} 2000 was tested in comparison with Nyex{sup TM} 1000, which is currently being used for a number of industrial waste water treatment applications. Nyex{sup TM} 1000 exhibited small adsorption capacity of 0.1 mg g{sup -1} for phenol because of having small specific surface area of 1 m{sup 2} g{sup -1}. In contrast, Nyex{sup TM} 2000 with specific surface area of 17 m{sup 2} g{sup -1} delivered an adsorption capacity of 0.8 mg g{sup -1}, which was eight-fold higher than that of Nyex{sup TM} 1000. Nyex{sup TM} 2000 was successfully electrochemically regenerated by passing a current of 0.5 A, charge passed of 31 C g{sup -1} for a treatment time of 45 minutes. These electrochemical parameters were comparable to Nyex{sup TM} 1000 for which a current of 0.5 A, charge passed of 5 C g{sup -1} for a treatment time of 20 minutes were applied for complete oxidation of adsorbed phenol. The comparatively high charge density was found to be required for Nyex{sup TM} 2000, which is justified with its higher adsorption capacity. The FTIR results validated the mineralization of adsorbed phenol into CO{sub 2} and H{sub 2}O except the formation of few by-products, which were in traces when compared with the concentration of phenol removed from aqueous solution. The electrical energy as required for electrochemical oxidation of phenol adsorbed onto Nyex{sup TM} 1000 and 2000 was found to be 214 and 196 J mg{sup -1}, respectively. The comparatively low energy requirement for electrochemical oxidation using Nyex{sup TM} 2000 is consistent with its higher bed electrical conductivity, which is twice that of Nyex{sup TM} 1000.

  8. Determination of aromatic amines in aqueous extracts of polyurethane foam using hydrophilic interaction liquid chromatography and mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Riddar Johnson, Jakob, E-mail: jakob.riddarjohnson@anchem.su.se [Work Environment Chemistry, Stockholm University, P.O. Box 460, 281 24 Haessleholm (Sweden); Karlsson, Daniel; Dalene, Marianne; Skarping, Gunnar [Work Environment Chemistry, Stockholm University, P.O. Box 460, 281 24 Haessleholm (Sweden)

    2010-09-23

    A method is presented for the determination of aromatic amines in aqueous extracts of polyurethane (PUR) foam. The method is based on the extraction of PUR foam using aqueous acetic acid (0.1%, w/v) followed by determination of extracted aromatic amines using hydrophilic interaction liquid chromatography (HILIC) and tandem mass spectrometry (MS/MS) with positive electrospray ionisation. The injections of volumes up to 5 {mu}L of aqueous solutions were made possible by on-column focusing with partially filled loop injections. The fragmentation patterns for 2,4- and 2,6-toluene diamine (TDA) and 4,4'-methylene dianiline (MDA) were clarified by performing a hydrogen-deuterium exchange study. TDA and MDA were determined using trideuterated 2,4- and 2,6-TDA and dideuterated 4,4'-MDA as internal standards. Linear calibration graphs were obtained over the range 0.025-0.5 {mu}g mL{sup -1} with correlation coefficients >0.996 and the instrumental detection limit for each compound was <50 fmol. The stability of the amines was influenced by the matrix, so their concentrations decreased over time. Agreement was observed between the results of analyses of PUR foam extracts by HILIC-MS/MS and results obtained by ethyl chloroformate derivatisation and reversed phase (RP) liquid chromatography-mass spectrometry (LC-MS/MS). TDA was observed to be unstable in extracts of foam but not in pure solutions.

  9. Aqueous Two-phase Systems with Ultrasonic Extraction Used for Extracting Phenolic Compounds from Inonotus obliquus

    Institute of Scientific and Technical Information of China (English)

    ZHAO; Yan-xia; LIU; Yu-bing; LIU; Feng; ZHENG; Wei-fa

    2013-01-01

    Objective To optimize the extracting technology of assessing the maximum yield of phenolic compounds (PC) from Inonotus obliquus by single factor experiments and orthogonal array design methods through aqueous two-phase systems combined with ultrasonic extraction. Methods The range of the independent variables, namely levels of acetone and ammonium sulfate, and ultrasonic time were identified by a first set of single factor experiments. The actual values of the independent variables coded at four levels and three factors were selected based on the results of the single factor experiments. Subsequently, the levels of acetone and ammonium sulfate, and ultrasonic time were optimized using the orthogonal array method. Results The optimum conditions for the extraction of PC were found to use 7.0 mL acetone, 5.5 mg ammonium sulfate, with ultrasonic time for 5 min. Under these optimized conditions, the experimental maximum yield of PC was 37.8 mg/g, much higher than that of the traditional ultrasonic extraction (UE, 29.0 mg/g). And the PC obtained by this method had stronger anti-oxidative activities than those by traditional UE method. Conclusion These results indicate the suitability of the models developed and the success in optimizing the extraction conditions. This is an economical and efficient method for extracting polyphenols from I. obliquus.

  10. Aqueous Two-phase Systems with Ultrasonic Extraction Used for Extracting Phenolic Compounds from Inonotus obliquus

    Institute of Scientific and Technical Information of China (English)

    ZHAO Yan-xia; LIU Yu-bing; LIU Feng; ZHENG Wei-fa

    2013-01-01

    Objective To optimize the extracting technology of assessing the maximum yield of phenolic compounds (PC)from Inonotus obliquus by single factor experiments and orthogonal array design methods through aqueous two-phase systems combined with ultrasonic extraction.Methods The range of the independent variables,namely levels of acetone and ammonium sulfate,and ultrasonic time were identified by a first set of single factor experiments.The actual values of the independent variables coded at four levels and three factors were selected based on the results of the single factor experiments.Subsequently,the levels of acetone and ammonium sulfate,and ultrasonic time were optimized using the orthogonal array method.Results The optimum conditions for the extraction of PC were found to use 7.0 mL acetone,5.5 mg ammonium sulfate,with ultrasonic time for 5 min.Under these optimized conditions,the experimental maximum yield of PC was 37.8 mg/g,much higher than that of the traditional ultrasonic extraction (UE,29.0 mg/g).And the PC obtained by this method had stronger anti-oxidative activities than those by traditional UE method.Conclusion These results indicate the suitability of the models developed and the success in optimizing the extraction conditions.This is an economical and efficient method for extracting polyphenols from Ⅰ.obliquus.

  11. A study on the reaction between CO2 and alkanolamines in aqueous solutions

    NARCIS (Netherlands)

    Blauwhoff, P.M.M.; Versteeg, G.F.; Swaaij, W.P.M. van

    1983-01-01

    Literature data on the rates of reaction between CO2 and alkanolamines (MEA, DEA, DIPA, TEA and MDEA) in aqueous solution are discussed. These data induced us to carry out absorption experiments of CO2 into aqueous DEA, DIPA, TEA and MDEA solutions from which the respective rate constants were deriv

  12. A study on the reaction between CO2 and alkanolamines in aqueous solutions

    NARCIS (Netherlands)

    Blauwhoff, P.M.M.; Versteeg, G.F.; Swaaij, W.P.M. van

    1984-01-01

    Literature data on the rates of reaction between CO2 and alkanolamines (MEA, DEA, DIPA, TEA and MDEA) in aqueous solution are discussed. These data induced us to carry out absorption experiments of CO2 into aqueous DEA, DIPA, TEA and MDEA solutions from which the respective rate constants were deriv

  13. In Situ Structural Characterization of Ferric Iron Dimers in Aqueous Solutions

    DEFF Research Database (Denmark)

    Zhu, Mengqiang; Puls, Brendan W.; Frandsen, Cathrine

    2013-01-01

    The structure of ferric iron (Fe3+) dimers in aqueous solutions has long been debated. In this work, we have determined the dimer structure in situ in aqueous solutions using extended X-ray absorption fine structure (EXAFS) spectroscopy. An Fe K-edge EXAFS analysis of 0.2 M ferric nitrate solutio...

  14. Density, Viscosity, Solubility, and Diffusivity of N2O in Aqueous Amino Acid Salt Solutions

    NARCIS (Netherlands)

    Kumar, P. Senthil; Hogendoorn, J.A.; Feron, P.H.M.; Versteeg, G.F.

    2001-01-01

    Solubility and diffusivity of N2O in aqueous solutions of potassium taurate are reported over a wide range of concentration and temperature. Also, the solubility of N2O in aqueous potassium glycinate solution is reported at 295 K. The ion specific constants are reported for taurate and glycinate ani

  15. The photochemical decomposition of Indol in an aqueous solution; Descomposicion fotoquimica de Indol en solucion acuosa

    Energy Technology Data Exchange (ETDEWEB)

    Ibarz, A.; Tejero, J.M.; Panades, R.

    1998-06-01

    The photo decomposition of Indol at different pH has been studied. The Indol photo decomposition rate in aqueous solution a maximum at pH 10. By means of a simple mechanism in three steps, it is possible to explain the kinetics behavior of the Indol photo decomposition in aqueous solution. (Author) 6 refs.

  16. Formation of quasi-free and bubble positronium states in water and aqueous solutions

    CERN Document Server

    Stepanov, Serge V; Byakov, Vsevolod M; Zvezhinskiy, D S; Subrahmanyam, V S

    2013-01-01

    It is shown that in aqueous solutions a positronium atom is first formed in the quasi-free state, and, after 50-100 ps, becomes localized in a nanobubble. Analysis of the annihilation spectra of NaNO3 aqueous solutions shows that the hydrated electron is not involved in the positronium (Ps) formation.

  17. Facile synthesis of “green” gold nanocrystals using cynarin in an aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Katircioğlu, Zeynep; Şakalak, Hüseyin [Department of Metallurgical and Materials Engineering, Selcuk University, Konya 42075 (Turkey); Nanobiotechnology Laboratory, Advanced Technology Research and Application Center, Selcuk University, Konya 42075 (Turkey); Ulaşan, Mehmet [Nanobiotechnology Laboratory, Advanced Technology Research and Application Center, Selcuk University, Konya 42075 (Turkey); Department of Chemistry, Selcuk University, Konya 42075 (Turkey); Gören, Ahmet Ceyhan, E-mail: ahmetceyhan.goren@tubitak.gov.tr [TÜBİTAK UME, Chemistry Group, Organic Chemistry Laboratories, 41470 Gebze, Kocaeli (Turkey); Yavuz, Mustafa Selman, E-mail: selmanyavuz@selcuk.edu.tr [Department of Metallurgical and Materials Engineering, Selcuk University, Konya 42075 (Turkey); Nanobiotechnology Laboratory, Advanced Technology Research and Application Center, Selcuk University, Konya 42075 (Turkey)

    2014-11-01

    Highlights: • The first time a remarkably simple, versatile, environmentally friendly, one-pot and biogenic fabrication and aqueous synthesis of monodisperse gold nanoparticles by using cynarin. • Cynarin as a reductant and capping agent. • Exclusion of extra reducing agents or reductant. • Fabrication of Pd and Ag nanoparticles using cynarin in aqueous media. - Abstract: Herein we describe a water-based protocol that generates Au nanoparticles (AuNPs) by mixing aqueous solutions of HAuCl4 and cynarin (a natural product extract from artichoke leaf). Based on the observations from {sup 1}H NMR spectrum of AuNPs, a polyol oxidation mechanism by metal ions which eventually results in AuNPs formation, is proposed. Basically, the aromatic alcohol groups (1,2-benzenediol) of cynarin are oxidized to α-hydroxy ketone intermediate product, and then further oxidized to the vicinal diketone final product while the Au{sup 3+} ions are reduced to its atomic form (Au{sup 0}) which leads the generation of Au nanoparticles. This new protocol has also been employed to prepare multiply twinned Pd nanoparticles and Ag cubical aggregates. Due to exclusion of organic solvent, surfactant, or stabilizer for all these synthesis, this protocol may provide a simple, versatile, and environmentally benign route to fabricate noble-metal nanoparticles having various compositions and morphologies.

  18. Optical properties of chitosan in aqueous solution of L- and D-ascorbic acids

    Science.gov (United States)

    Malinkina, Olga N.; Shipovskaya, Anna B.; Kazmicheva, Olga F.

    2016-04-01

    The optical properties of aqueous chitosan solutions in L- and D-ascorbic acids were studied by optical rotatory dispersion and spectrophotometry. The specific optical rotation [α] of all chitosan solutions tested was positive, in contrast to aqueous solutions of the ascorbic acid enantiomers, which exhibit an inverse relationship of [α] values. Significant differences in the absolute values of [α] of the chitosan solutions at polymer-acid ratios exceeding the equimolar one were found.

  19. Study of Elaeagnus angustifolia Fruit Aqueous Extract on the Histomorphometrical Changes of Retina in Mouse Embryo

    Directory of Open Access Journals (Sweden)

    Jamshid Arum

    2016-09-01

    Full Text Available Background Modern societies tend to use herbs or traditional medicine because of fewer side effects than synthetic drugs. Elaeagnus angustifolia is a plant with many therapeutic effects. Objectives This study aimed to investigate the effect of aqueous extract of Elaeagnus angustifolia on fetal mice retina in Balb/C by evaluating of histomophometrical and immunohistochemical parameters in the eye mouse embryos Methods In this experimental study, thirty pregnant mice were randomly divided into two groups. Control group received food and drinking water, and the experimental group received food and the aqueous extract at a dose of 500 mg/kg in the form of water solution from the day zero of pregnancy up to the 18th day. Pregnant mice were killed and their fetuses were taken, fixed and stained with hematoxylin-eosin. Histomorphometrical and immunohistochemical changes of retin examined. Results The mean of Crown-Rump length and weight of fetuses significantly increased in experimental group compared to control group. In experimental group, a significant decrease was shown in the mean of diameters and weight of placenta compared to control group. Retinal thickness in posterior, superior and inferior part significantly reduced in experimental group compared to control group. however, retinal thickness in anterior part in experimental group was not different when compared to control group. The number of Ki-67-positive cells showed that the retinal cells proliferation in experimental group decreased compared to control group. Conclusions The use of aqueous extract of Elaeagnus angustifolia at dose of 500 mg/kg to pregnant mice caused the growth and histological changes on fetal mouse and in the retinal mouse development.

  20. Acute toxicity and cytotoxicity evaluation of Dendrobium moniliforme aqueous extract in vivo and in vitro

    Science.gov (United States)

    Lee, Mu-Jin; Jung, Ho-Kyung; Kim, Min-Suk; Jang, Ji-Hun; Sim, Mi-Ok; Kim, Tea-Mook; Park, Ho; Ahn, Byung-Kwan; Cho, Hyun-Woo; Cho, Jung-Hee

    2016-01-01

    Dendrobium moniliforme (L.) Sw., an herb of the Orchidaceae family, has long been used in traditional medicine to strengthen bones, nourish the stomach, and promote the production of bodily fluid. Recently, polysaccharides isolated from Dendrobium have been used in functional foods and nutraceutical products. A traditional method to process Dendrobium is to soak fresh stems in an ethanol solution, which is the most important factor to ensure high yields of aqueous-extractable polysaccharides. The present study was carried out to investigate the potential acute toxicity of D. moniliforme aqueous extract (DMAE), by a single oral dose in Sprague-Dawley rats. The test article was orally administered once by gavage to male and female rats at doses of 0, 2,500, and 5,000 mg/kg body weight (n=5 male and female rats for each dose). Throughout the study period, no treatment-related deaths were observed and no adverse effects were noted in clinical signs, body weight, food consumption, serum biochemistry, organ weight, or gross findings at any dose tested. The results show that a single oral administration of DMAE did not induce any toxic effects at a dose below 5,000 mg/kg in rats, and the minimal lethal dose was considered to be over 5,000 mg/kg body weight for both sexes. With respect to cytotoxicity, the cell viability of human embryonic kidney (HEK293) cells was less than 50% when the cells were treated with 10 mg/mL aqueous extract for 24 h. PMID:27729930

  1. Aqueous extract of Rosmarinus officinalis L. inhibits neutrophil influx and cytokine secretion.

    Science.gov (United States)

    Silva, Ana Mara de Oliveira E; Machado, Isabel Daufenback; Santin, José Roberto; de Melo, Illana Louise Pereira; Pedrosa, Gabriela Vieira; Genovese, Maria Ines; Farsky, Sandra Helena Poliselli; Mancini-Filho, Jorge

    2015-01-01

    Rosmarinus officinalis L. phenolic compounds have attracted considerable attention because of their antioxidant and antimicrobial properties, including its ability to treat inflammatory disorders. In this work, we investigated the in vivo and in vitro effects of R. officinalis aqueous extract on neutrophil trafficking from the blood into an inflamed tissue, on cell-derived secretion of chemical mediators, and on oxidative stress. Anti-inflammatory activity was investigated using carrageenan-induced inflammation in the subcutaneous tissue of male Wistar rats orally treated with the R. officinalis extract (100, 200, or 400 mg/kg). The leukocyte influx (optical microscopy), secretion of chemical mediators (prostaglandin E2 (PGE2), TNF-α, interleukin 6 (IL-6), leukotriene B4 (LTB4), and cytokine-induced neutrophil chemoattractant 1 by enzyme-linked immunosorbent assay), and the anti-oxidative profile (super oxide dismutase (SOD), glutathione peroxidase, and thiobarbituric acid reactive substance (TBARS) spectrophotometry) were quantified in the inflamed exudate. N-Formyl-methionine-leucine-phenylalanine-induced chemotaxis, lipopolysaccharide-induced NO2 (-) production (Greiss reaction), and adhesion molecule expression (flow cytometry) were in vitro quantified using oyster glycogen recruited peritoneal neutrophils previous treated with the extract (1, 10, or 100 µg/mL). Animals orally treated with phosphate-buffered saline and neutrophils incubated with Hank's balanced salt solution were used as control. R. officinalis extract oral treatment caused a dose-dependent reduction in the neutrophil migration as well as decreased SOD, TBARS, LTB4, PGE2, IL-6, and TNF-α levels in the inflamed exudate. In vitro treatment with R. officinalis decreased neutrophil chemotaxis, NO2 (-) production, and shedding of L-selectin and β2 integrin expressions. Results here presented show that R. officinalis aqueous extract displays important in vivo and in vitro anti

  2. Studies on the mechanism of efficient extraction of tea components by aqueous ethanol.

    Science.gov (United States)

    Hu, Ci-Jie; Gao, Ying; Liu, Yang; Zheng, Xin-Qiang; Ye, Jian-Hui; Liang, Yue-Rong; Lu, Jian-Liang

    2016-03-01

    Effect of solvent on the extraction yield and its relevant mechanism have been studied in this paper. Compared with extraction by water, catechins and caffeine could be easily extracted from green tea by aqueous ethanol, but hardly at all by absolute ethanol. Results of the vacuum-assisted extraction, solubility determination of EGCG and caffeine, as well as swelling ratio analysis of the infused leaves, indicated that an excellent leaf-matrix-swelling effect and high solubility of tea components might be the key mechanisms for high extraction efficiency by the aqueous ethanol. These mechanisms were further confirmed by the pre-swelling extraction. This is a first report on the mechanism of efficient extraction by aqueous organic solvent. Application of pre-swelling extraction is also discussed.

  3. Non-aqueous phase liquid spreading during soil vapor extraction

    Science.gov (United States)

    Kneafsey, Timothy J.; Hunt, James R.

    2004-02-01

    Many non-aqueous phase liquids (NAPLs) are expected to spread at the air-water interface, particularly under non-equilibrium conditions. In the vadose zone, this spreading should increase the surface area for mass transfer and the efficiency of volatile NAPL recovery by soil vapor extraction (SVE). Observations of spreading on water wet surfaces led to a conceptual model of oil spreading vertically above a NAPL pool in the vadose zone. Analysis of this model predicts that spreading can enhance the SVE contaminant recovery compared to conditions where the liquid does not spread. Experiments were conducted with spreading volatile oils hexane and heptane in wet porous media and capillary tubes, where spreading was observed at the scale of centimeters. Within porous medium columns up to a meter in height containing stagnant gas, spreading was less than ten centimeters and did not contribute significantly to hexane volatilization. Water film thinning and oil film pinning may have prevented significant oil film spreading, and thus did not enhance SVE at the scale of a meter. The experiments performed indicate that volatile oil spreading at the field scale is unlikely to contribute significantly to the efficiency of SVE.

  4. Removal of nitrate and phosphate from aqueous solutions by microalgae

    Directory of Open Access Journals (Sweden)

    M.H. Sayadi

    2016-12-01

    Full Text Available The aim of this study was to evaluate the ability of microalgae Spirulina platensis and Chlorella vulgaris to remove nitrate and phosphate in aqueous solutions. Spirulina platensis and Chlorella vulgar is microalgae was collected in 1000 ml of municipal water and KNO3, K2HPO4 was added as sources of nitrate and phosphate in three different concentrations (0.25, 0.35 and 0.45g/L. During the growth period, the concentration of nitrate and phosphate was recorded at 1, 4, 6 and 8 days. The highest nitrate removal on the 8 day for Chlorella vulgaris was 89.80% at the treatment of 0.25g/L and for Spirulina platensis was 81.49% at the treatment of 0.25g/L. The highest phosphate removal for Spirulina platensis was 81.49% at the treatment of 0.45g/L and for Chlorella vulgaris was 88% at the treatment of 0.45g/L. The statistical results showed that the amount of phosphate and nitrate removal during different time periods by Chlorella vulgaris depicted a significant difference at P

  5. Electrochemical degradation of amaranth aqueous solution on ACF.

    Science.gov (United States)

    Fan, Li; Zhou, Yanwei; Yang, Weishen; Chen, Guohua; Yang, Fenglin

    2006-09-21

    The degradation of Amaranth, a kind of azo dye, has been studied under galvanostatic model with activated carbon fiber (ACF) electrode in aqueous solution with electrochemical method. The ACF was used as anode and cathode, respectively for the decolorization process. The onset oxidation potential and reduction potential for Amaranth on ACF were respectively ascertained at 0.6 and -0.4 V. During the range of -1.1 to 0.50 mA cm(-2), the decolorization was clarified into three processes as electroreduction, adsorption and electrooxidation. There were little contributions to the color and COD removals for the process of adsorption. The color removal can be up to 99% when the current density was 0.50 mA cm(-2). The maximum COD removal was 52% for the process of electrooxidation. Hundred percent color removal was obtained when the current density of -1.0 mA cm(-2) was applied. The maximum COD removal was 62% for the electroreduction. The COD removal results from the adsorption of products for the decolorization process of electrooxidation or electroreduction.

  6. Cadmium Removal from Aqueous Solutions by Ground Pine Cone

    Directory of Open Access Journals (Sweden)

    H Izanloo, S Nasseri

    2005-01-01

    Full Text Available A study on the removal of cadmium ions from aqueous solutions by pine cone was conducted in batch conditions. Kinetic data and equilibrium removal isotherms were obtained. The influence of different experimental parameters such as contact time, initial concentration of cadmium, pine cone mass and particle size, and temperature on the kinetics of cadmium removal was studied. Results showed that the main parameters that played an important role in removal phenomenon were initial cadmium concentration, particle size and pine cone mass. The necessary time to reach equilibrium was between 4 and 7 hours based on the initial concentration of cadmium. The capacity of cadmium adsorption at equilibrium increased with the decrease of pine cone particle size. The capacity of cadmium adsorption at equilibrium by pine cone increased with the quantity of pine cone introduced (1–4 g/L. Temperature in the range of 20-30°C showed a restricted effect on the removal kinetics (13.56 mg/g at 20°C and a low capacity of adsorption about 11.48 mg/g at 30°C. The process followed pseudo second-order kinetics. The cadmium uptake of pine cone was quantitatively evaluated using adsorption isotherms. Results indicated that the Langmuir model gave a better fit to the experimental data in comparison with the Freundlich equation.

  7. Sonochemical degradation of organophosphorus pesticide in dilute aqueous solutions

    Institute of Scientific and Technical Information of China (English)

    Robina Farooq; FENG Kai-lin; S. F. Shaukat; HUANG Jian-jun

    2003-01-01

    Ultrasonic irradiation was found to accelerate the rate of hydrolysis of omethoate in aqueous solution over the pH range of 2-12. Process parameters studied include pH, steady-state temperature, concentration, and the type of gases. Greater than 96% hydrolysis was observed in 30 minutes through this process and the rate of destruction increased with the help of more soluble and low thermal inert gas. So with Krypton, omethoate was found to undergo rapid destruction as compared with Argon. In the presence of ultrasound, the observed first-order rate of hydrolysis of omethoate is found to be independent of pH. The formation of transient supercritical water(SCW) appears to be an important factor in the acceleration of chemical reactions in the presence of ultrasound. A detailed chemical reaction mechanism for omethoate destruction in water was formulated. Experimental results and theoretical kinetic mechanism demonstrated that the most of the omethoate undergo destruction inside the cavitating holes. A very less effect of temperature on the degradation of omethoate within a temperature range of 20-70℃ proves that a small quantity of omethoate undergoes secondary destruction in the bulk liquid.

  8. SORPTION OF Cu2+ FROM AQUEOUS SOLUTIONS BY SLOVAK BENTONITES

    Directory of Open Access Journals (Sweden)

    ANNA BRTÁŇOVÁ

    2012-03-01

    Full Text Available Bentonites are used as barriers in landfills, or in areas of old mining activities to prevent contamination of environment by leachates containing heavy metals. Batch experiments were performed under static conditions to study sorption of Cu2+ from aqueous solutions via adsorption on industrial products made from Slovak bentonites Lieskovec and Jelšový Potok. The samples were characterized by X-ray powder diffraction, infrared spectroscopy and by specific surface area and cation exchange capacities measurements. Effects of pH, concentration of metal cations and contact time were analysed. The adsorption was strongly dependent on pH of the medium, and the uptake of adsorbed metal increased from pH 2.0 to 6.5, while the solubility of Cu at higher pH values decreased. The uptake of Cu2+ was rapid and it increased with increasing metal concentration, while the relative amount of adsorbed Cu2+ decreased. The equilibrium adsorption capacity of the adsorbents used for Cu2+ was extrapolated using the linear Freundlich and Langmuir adsorption isotherms. The Langmuir isotherm was found to fit better the experimental data measured for both bentonites.

  9. Adsorption removal of thiocyanate from aqueous solution by calcined hydrotalcite

    Institute of Scientific and Technical Information of China (English)

    LI Yu-jiang; YANG Min; ZHANG Xiao-jin; WU Tao; CAO Nan; WEI Na; BI Yan-jun; WANG Jing

    2006-01-01

    A hydrotalcite with Mg/Al molar ratio 2 was prepared by co-precipitation method and was characterized by XRD,TG/DTA, Zeta potential and BET surface area. The hydrotalcite was calcined at 500℃, with the dehydration from interlayer, the dehydroxilation from the brucite-like layer and the decomposition of carbonate successively, transformed into the mixed oxide type.The removal of thiocyanate from aqueous solution by using the original hydrotalcite and calcined hydrotalcite (HTC-500) was investigated. The results showed that the thiocyanate adsorption capacity of calcined hydrotalcite was much higher than that of the original form. Calcined hydrotalcite was particularly effective at removing thiocyanate, and that the effective range of pH for the thiocyanate removal are between 5.5-10.0. The experimental data of thiocyanate removal fit nicely with Langmuir isotherm, and the saturated adsorption uptake was 96.2 mg SCN-/g HTC-500. The adsorption ofthiocyanate by calcined hydrotalcite follows first-order kinetics. And the intercalation to the structure recovery for calcined hydrotalcite. But the presence of additional anions could affect the adsorption behavior of thiocyanate.

  10. Adsorption removal of thiocyanate from aqueous solution by calcined hydrotalcite.

    Science.gov (United States)

    Li, Yu-Jiang; Yang, Min; Zhang, Xiao-Jin; Wu, Tao; Cao, Nan; Wei, Na; Bi, Yan-Jun; Wang, Jing

    2006-01-01

    A hydrotalcite with Mg/Al molar ratio 2 was prepared by co-precipitation method and was characterized by XRD, TG/DTA, Zeta potential and BET surface area. The hydrotalcite was calcined at 500 degrees C, with the dehydration from interlayer, the dehydroxilation from the brucite-like layer and the decomposition of carbonate successively, transformed into the mixed oxide type. The removal of thiocyanate from aqueous solution by using the original hydrotalcite and calcined hydrotalcite (HTC-500) was investigated. The results showed that the thiocyanate adsorption capacity of calcined hydrotalcite was much higher than that of the original form. Calcined hydrotalcite was particularly effective at removing thiocyanate, and that the effective range of pH for the thiocyanate removal are between 5.5-10.0. The experimental data of thiocyanate removal fit nicely with Langmuir isotherm, and the saturated adsorption uptake was 96.2 mg SCN-/g HTC-500. The adsorption of thiocyanate by calcined hydrotalcite follows first-order kinetics. And the intercalation to the structure recovery for calcined hydrotalcite. But the presence of additional anions could affect the adsorption behavior of thiocyanate.

  11. Lifetimes of -halo and -azidobenzyl carbocations in aqueous solution

    Indian Academy of Sciences (India)

    R Sanjeev; V Jagannadham

    2002-02-01

    The title cations were produced in aqueous solution by chemical initiation (solvolysis) of benzyl-gem-dihalides and benzyl-gem-diazides. The solvolysis reactions of benzyl-gem-dihalides and benzyl-gem-diazides in water proceed by a stepwise mechanism through -halobenzyl carbocation and -azidobenzyl carbocation intermediates, which are captured by water to give the corresponding carbonyl compounds as the sole detectable products. Rate constant ratio / (M-1) for partitioning of the carbocation between reaction with halide/azide ion and reaction with water is determined by analysis of halide/azide common ion inhibition of the solvolysis reaction. The rate constants (s-1) for the reaction of the cation with solvent water were determined from the experimental values of / and solv, for the solvolysis of the benzyl-gem-dihalides and benzyl-gem-diazides respectively, using = 5 × 109 M-1 s-1 for diffusion-limited reaction of halide/azide ion with -substituted benzyl carbocations. The values of 1/ are thus the lifetimes of the -halobenzyl carbocations and -azidobenzyl carbocations respectively.

  12. The evaporation behavior of sessile droplets from aqueous saline solutions.

    Science.gov (United States)

    Soulié, Virginie; Karpitschka, Stefan; Lequien, Florence; Prené, Philippe; Zemb, Thomas; Moehwald, Helmuth; Riegler, Hans

    2015-09-14

    Quantitative experiments on the evaporation from sessile droplets of aqueous saline (NaCl) solutions show a strong dependence on salt concentration and droplet shape. The experiments were performed with seven decades of initial NaCl concentrations, with various droplet sizes and with different contact angles. The evaporation rate is significantly lower for high salt concentrations and small contact angles than what is expected from the well-accepted diffusion-controlled evaporation scenario for sessile droplets, even if the change of the vapor pressure due to the salt is taken into account. Particle tracking velocimetry reveals that this modification of the evaporation behavior is caused by marangoni flows that are induced by surface tension gradients originating from the local evaporative peripheral salt enrichment. In addition it is found that already very low salt concentrations lead to a pinning of the three phase contact line. Whereas droplets with concentration ≥10(-6) M NaCl are pinned as soon as evaporation starts, droplets with lower salt concentration do evaporate in a constant contact angle mode. Aside from new, fundamental insights the findings are also relevant for a better understanding of the widespread phenomenon of corrosion initiated by sessile droplets.

  13. Photo- and thermal degradation of piroxicam in aqueous solution

    Directory of Open Access Journals (Sweden)

    M Aminuddin

    2011-01-01

    Full Text Available Light and temperature have considerable effect on the degradation of piroxicam in aqueous solutions. The pH and acetate buffer ions also affect the degradation process. The apparent first-order rate constants for the photochemical and thermal degradation of piroxicam have been determined as 2.04-10.01 and 0.86-3.06×10−3 min−1 , respectively. The first-order plots for the degradation of piroxicam showed good linearity within a range of 20-50% loss of piroxicam at pH 2.0-12.0. The rate-pH profile for the photodegradation of piroxicam is a U-shaped curve and for the thermal degradation a bell-shaped curve in the pH range of 2.0-12.0. The thermal degradation of piroxicam was maximum around pH 6.0. It is increased in the presence of acetate ions but was not affected by citrate and phosphate ions.

  14. ADSORPTION FROM AQUEOUS SOLUTION ONTO NATURAL AND ACID ACTIVATED BENTONITE

    Directory of Open Access Journals (Sweden)

    Laila Al-Khatib

    2012-01-01

    Full Text Available Dyes have long been used in dyeing, paper and pulp, textiles, plastics, leather, paint, cosmetics and food industries. Nowadays, more than 100,000 commercial dyes are available with a total production of 700,000 tones manufactured all over the world annually. About 10-15% of dyes are being disposed off as a waste into the environment after dyeing process. This poses certain hazards and environmental problems. The objective of this study is to investigate the adsorption behavior of Methylene Blue (MB from aqueous solution onto natural and acid activated Jordanian bentonite. Both bentonites are firstly characterized using XRD, FTIR and SEM techniques. Then batch adsorption experiments were conducted to investigate the effect of initial MB concentration, contact time, pH and temperature. It was found that the percentage of dye removal was improved from 75.8% for natural bentonite to reach 99.6% for acid treated bentonite. The rate of MB removal followed the pseudo second order model with a high correlation factor. The Langmuir and Freundlich adsorption models were applied to describe the equilibrium isotherms. The Langmuir isotherm model was found more representative. The results indicate that bentonite could be employed as a low cost adsorbent in wastewater treatment for the removal of colour and dyes.

  15. Defluoridation from aqueous solutions by granular ferric hydroxide (GFH).

    Science.gov (United States)

    Kumar, Eva; Bhatnagar, Amit; Ji, Minkyu; Jung, Woosik; Lee, Sang-Hun; Kim, Sun-Joon; Lee, Giehyeon; Song, Hocheol; Choi, Jae-Young; Yang, Jung-Seok; Jeon, Byong-Hun

    2009-02-01

    This research was undertaken to evaluate the feasibility of granular ferric hydroxide (GFH) for fluoride removal from aqueous solutions. Batch experiments were performed to study the influence of various experimental parameters such as contact time (1 min-24h), initial fluoride concentration (1-100 mgL(-1)), temperature (10 and 25 degrees C), pH (3-12) and the presence of competing anions on the adsorption of fluoride on GFH. Kinetic data revealed that the uptake rate of fluoride was rapid in the beginning and 95% adsorption was completed within 10 min and equilibrium was achieved within 60 min. The sorption process was well explained with pseudo-first-order and pore diffusion models. The maximum adsorption capacity of GFH for fluoride removal was 7.0 mgg(-1). The adsorption was found to be an endothermic process and data conform to Langmuir model. The optimum fluoride removal was observed between pH ranges of 4-8. The fluoride adsorption was decreased in the presence of phosphate followed by carbonate and sulphate. Results from this study demonstrated potential utility of GFH that could be developed into a viable technology for fluoride removal from drinking water.

  16. Structure of aqueous electrolyte solutions near a hydrophobic surface

    Directory of Open Access Journals (Sweden)

    M.Kinoshita

    2007-09-01

    Full Text Available The structure of aqueous solutions of 1:1 salts (KCl, NaCl, KF,and CsI near a hydrophobic surface is analysed using the angle-dependent integral equation theory. Water molecules are taken to be hard spheres imbedded with multipolar moments including terms up to octupole order, and hard spherical ions are immersed in this model water. The many-body interactions associated with molecular polarizability are treated at the self-consistent mean field level. The effects of cationic and anionic sizes and salt concentration in the bulk are discussed in detail. As the salt concentration increases, the layer of water molecules next to the surface becomes denser but its orientational order remains almost unchanged. The concentration of each ion at the surface can be drastically different from that in the bulk. Asa striking example, at sufficiently low salt concentrations, the concentration of I- is about 500 times higher than that of F- at the surface.

  17. Effect of nanotechnology on heavy metal removal from aqueous solution

    Institute of Scientific and Technical Information of China (English)

    Hoda Kahrizi; Ali Bafkar; Masumeh Farasati

    2016-01-01

    The effect of nanotechnology on cadmium and zinc removal from aqueous solution was investigated. In order to characterize micro and nano phragmites australis adsorbent, we analyzed the data via FTIR, SEM, PSA, and EDX. The effect of various parameters such as pH, contact time, amount of adsorbent and initial concentration, was investigated. The optimum pH for the removal of cadmium for micro and nano phragmites australis adsorbent was 7, and for the removal of zinc by the micro adsorbent was 7 and by nano adsorbent was 6. The equilibrium time of zinc was 90 min and for the adsorption of cadmium by micro and nano adsorbent were 90 and 30 min, respectively. The optimum dose of micro adsorbent for the removal of cadmium was 0.7 g, and the other dose for the removal of zinc and cadmium was 0.5 g. The evaluation of adsorbent’s distribution coefficient showed that the highest rates of distribution coefficient with initial concentration of 5, 10, 30, and 50 mg/L were 394.83, 587.62, 759.39 and 1101.52 L/kg, respectively, which were observed in nano adsorbent. Desorption experiments for the nano adsorbent in three cycles were done. Among kinetics models, our experimental data were more consistent with Hoo kinetic model and for isotherm models, Freundlich isotherm was more consistent. The results show that nanotechnology could increase the performance of adsorbents and enhance the efficiency of the adsorption of cadmium and zinc ions.

  18. Modeling platinum group metal complexes in aqueous solution.

    Science.gov (United States)

    Lienke, A; Klatt, G; Robinson, D J; Koch, K R; Naidoo, K J

    2001-05-07

    We construct force fields suited for the study of three platinum group metals (PGM) as chloranions in aqueous solution from quantum chemical computations and report experimental data. Density functional theory (DFT) using the local density approximation (LDA), as well as extended basis sets that incorporate relativistic corrections for the transition metal atoms, has been used to obtain equilibrium geometries, harmonic vibrational frequencies, and atomic charges for the complexes. We found that DFT calculations of [PtCl(6)](2-).3H(2)O, [PdCl(4)](2-).2H(2)O, and [RhCl(6)](3-).3H(2)O water clusters compared well with molecular mechanics (MM) calculations using the specific force field developed here. The force field performed equally well in condensed phase simulations. A 500 ps molecular dynamics (MD) simulation of [PtCl(6)](2-) in water was used to study the structure of the solvation shell around the anion. The resulting data were compared to an experimental radial distribution function derived from X-ray diffraction experiments. We found the calculated pair correlation functions (PCF) for hexachloroplatinate to be in good agreement with experiment and were able to use the simulation results to identify and resolve two water-anion peaks in the experimental spectrum.

  19. Morphology control of brushite prepared by aqueous solution synthesis

    Directory of Open Access Journals (Sweden)

    T. Toshima

    2014-03-01

    Full Text Available Dicalcium phosphate dihydrate (DCPD, CaHPO4·2H2O, also known as brushite, is one of the important bioceramics due to not only diseases factors such as kidney stone and plaque formation but also purpose as fluoride insolubilization material. It is used medicinally to supply calcium, and is of interest for its unique properties in biological and pathological mineralization. It is important to control the crystal morphology of brushite since its chemical reactivity depends strongly on its surface properties; thus, its morphology is a key issue for its applications as a functional material or precursor for other bioceramics. Here, we report the effects of the initial pH and the Ca and phosphate ion concentrations on the morphology of DCPD particles during aqueous solution synthesis. Crystal morphologies were analyzed by scanning electron microscopy and X-ray diffraction. The morphology phase diagram of DCPD crystallization revealed that increasing the initial pH and/or ion concentration transformed DCPD morphology from petal-like into plate-like structures.

  20. Heavy metal removal from aqueous solutions by activated phosphate rock

    Energy Technology Data Exchange (ETDEWEB)

    Elouear, Z. [Laboratoire Eau Energie et Environnement, Departement de genie geologique, Ecole Nationale d' Ingenieurs de Sfax, BP W 3038, Sfax (Tunisia)], E-mail: zouheir.elouaer@tunet.tn; Bouzid, J.; Boujelben, N. [Laboratoire Eau Energie et Environnement, Departement de genie geologique, Ecole Nationale d' Ingenieurs de Sfax, BP W 3038, Sfax (Tunisia); Feki, M. [Unite de chimie industriel I, Ecole Nationale d' Ingenieurs de Sfax, BP W 3038 Sfax (Tunisia); Jamoussi, F. [Laboratoire de Georessources CERTE BP 95, 2050 Hamam-Lif (Tunisia); Montiel, A. [Societe Anonyme de Gestion des Eaux de Paris, 9 rue Schoelcher, 75675 Paris cedex 14 (France)

    2008-08-15

    The use of natural adsorbent such as phosphate rock to replace expensive imported synthetic adsorbent is particularly appropriate for developing countries such as Tunisia. In this study, the removal characteristics of lead, cadmium, copper and zinc ions from aqueous solution by activated phosphate rock were investigated under various operating variables like contact time, solution pH, initial metal concentration and temperature. The kinetic and the sorption process of these metal ions were compared for phosphate rock (PR) and activated phosphate rock (APR). To accomplish this objective we have: (a) characterized both (PR) and (APR) using different techniques (XRD, IR) and analyses (EDAX, BET-N{sub 2}); and, (b) qualified and quantified the interaction of Pb{sup 2+}, Cd{sup 2+}, Cu{sup 2+} and Zn{sup 2+} with these sorbents through batch experiments. Initial uptake of these metal ions increases with time up to 1 h for (PR) and 2 h for (APR), after then, it reaches equilibrium. The maximum sorption obtained for (PR) and (APR) is between pH 2 and 3 for Pb{sup 2+} and 4 and 6 for Cd{sup 2+}, Cu{sup 2+} and Zn{sup 2+}. The effect of temperature has been carried out at 10, 20 and 40 deg. C. The data obtained from sorption isotherms of metal ions at different temperatures fit to linear form of Langmuir sorption equation. The heat of sorption ({delta}H{sup o}), free energy ({delta}G{sup o}) and change in entropy ({delta}S{sup o}) were calculated. They show that sorption of Pb{sup 2+}, Cd{sup 2+}, Cu{sup 2+} and Zn{sup 2+}on (PR) and (APR) an endothermic process. These findings are significant for future using of (APR) for the removal of heavy metal ions from wastewater under realistic competitive conditions in terms of initial heavy metals, concentrations and pH.

  1. Spreading of aqueous SDS solutions over nitrocellulose membranes.

    Science.gov (United States)

    Zhdanov, S A; Starov, V M; Sobolev, V D; Velarde, M G

    2003-08-15

    Experimental investigations were carried out on the spreading of small drops of aqueous SDS solutions over dry thin porous substrates (nitrocellulose membranes) in the case of partial wetting. The time evolution was monitored of the radii of both the drop base and the wetted area inside the porous substrate. The total duration of the spreading process was subdivided into three stages: the first stage: the drop base expands until the maximum value of the drop base is reached, the contact angle rapidly decreases during this stage; the second stage: the radius of the drop base remains constant and the contact angle decreases linearly with time; the third stage: the drop base shrinks and the contact angle remains constant. The wetted area inside the porous substrate expends during the whole spreading process. Appropriate scales were used with a plot of the dimensionless radii of the drop base, of the wetted area inside the porous substrate and the dynamic contact angle on the dimensionless time. Our experimental data show: the overall time of the spreading of drops of SDS solution over dry thin porous substrates decreases with the increase of surfactant concentration; the difference between advancing and hydrodynamic receding contact angles decreases with the surfactant concentration increase; the constancy of the contact angle during the third stage of spreading has nothing to do with the hysteresis of contact angle, but determined by the hydrodynamic reasons. It is shown using independent spreading experiments of the same drops on nonporous nitrocellulose substrate that the static receding contact angle is equal to zero, which supports our conclusion on the hydrodynamic nature of the hydrodynamic receding contact angle on porous substrates.

  2. Evaluation of an integrated extraction process for in-situ phenol removal with micellar solutions of PEO-PPO-PEO block copolymers

    NARCIS (Netherlands)

    Heerema, L.D.; Cakali, D.; Roelands, C.P.M.; Goetheer, E.L.V.; Verdoes, D.; Keurentjes, J.

    2010-01-01

    This paper evaluates the applicability of aqueous solutions of Pluronics for the removal of phenol in a separation and regeneration process. Experimental results show that Pluronic P103 micelles allow extraction of phenol from aqueous solutions at 30°C. The phenol can be released due to the transiti

  3. Reomoval of Heavy Metals from Aqueous Solutions using Bascteria

    Institute of Scientific and Technical Information of China (English)

    HUANGMin-sheng; PANjing; 等

    2001-01-01

    The accumulation of heavy metals by microbial biomass with high surface area-to-volume ratio holds great potential for heavy metal removal in both soluble and particular forms,especially when the heavy metal concentrations are low(<50mg/L),E.coli and B.Subtilis are effective agents for metal removal.We further investigated the effect of pH,temperature,equilibration time,and pre-treatment reagents on the removal of pH(Ⅱ),Cd(Ⅱ) and Cr(VI) from aqueous solutions by E.Coli and B.subtilis.E.coli and B.subtilis were cultivated for 60 hours,the experimentally determined optimal cultivation time before they were used in metal removal experiments,Under the optimal conditions of pH 6.0,equilibration temperature 30℃ and equilibration time 1 hour,63.39% and 69.90%Cd(Ⅱ) can be removed by E.coli and B.subtilis.Under the optimal conditions of pH5.5,equilibration temperature 30℃ and equliobration time 1 hour,68.51% and 67.36% pB(Ⅱ) can be removed by E.coli and B.subtilis.And under the optimal conditons of pH5.5,equilibration temperature 30℃,and equilibration time 1 hour,60.26% and 54.56% Cr(VI) can be removed by E.coli and B.subtilis.Chemical treatment of cultivated bacteria(0.1mol/L NaOH,0.1mol/L HCl,30% ethanol,and distilled water)affects the efficiency of metal removal by E.coli and B.subtilis,pretreatment of biomass by NaOH enhanced Cd(Ⅱ),Pb(Ⅱ)and Cr(VI) removal,while preteatment by HCl,ethanol and distilled water reduced Ca(Ⅱ) ,Pb(Ⅱ) and Cr(VI) removal,For metal removal from industrial waste discharges,pretreated biomass of E.coli can remove 68.5% of Cd and 58.1% of Cr from solutions,while pretreated biomass of B.subtilis can remove 62.6% of Cd and 57% of Cr from Solutions.

  4. Biosynthesis of Monascus pigments by resting cell submerged culture in nonionic surfactant micelle aqueous solution.

    Science.gov (United States)

    Wang, Bo; Zhang, Xuehong; Wu, Zhenqiang; Wang, Zhilong

    2016-08-01

    Growing cell submerged culture is usually applied for fermentative production of intracellular orange Monascus pigments, in which accumulation of Monascus pigments is at least partially associated to cell growth. In the present work, extractive fermentation in a nonionic surfactant micelle aqueous solution was utilized as a strategy for releasing of intracellular Monascus pigments. Those mycelia with low content of intracellular Monascus pigments were utilized as biocatalyst in resting cell submerged culture. By this means, resting cell submerged culture for production of orange Monascus pigments was carried out successfully in the nonionic surfactant micelle aqueous solution, which exhibited some advantages comparing with the corresponding conventional growing cell submerged culture, such as non-sterilization operation, high cell density (24 g/l DCW) leading to high productivity (14 AU of orange Monascus pigments at 470 nm per day), and recycling of cells as biocatalyst leading to high product yield (approximately 1 AU of orange Monascus pigments at 470 nm per gram of glucose) based on energy metabolism.

  5. Biological Activities of Aqueous and Organic Extracts from Tropical Marine Sponges

    Directory of Open Access Journals (Sweden)

    Tom Turk

    2010-04-01

    Full Text Available We report on screening tests of 66 extracts obtained from 35 marine sponge species from the Caribbean Sea (Curaçao and from eight species from the Great Barrier Reef (Lizard Island. Extracts were prepared in aqueous and organic solvents and were tested for hemolytic, hemagglutinating, antibacterial and anti-acetylcholinesterase (AChE activities, as well as their ability to inhibit or activate cell protein phosphatase 1 (PP1. The most interesting activities were obtained from extracts of Ircinia felix, Pandaros acanthifolium, Topsentia ophiraphidites, Verongula rigida and Neofibularia nolitangere. Aqueous and organic extracts of I. felix and V. rigida showed strong antibacterial activity. Topsentia aqueous and some organic extracts were strongly hemolytic, as were all organic extracts from I. felix. The strongest hemolytic activity was observed in aqueous extracts from P. acanthifolium. Organic extracts of N. nolitangere and I. felix inhibited PP1. The aqueous extract from Myrmekioderma styx possessed the strongest hemagglutinating activity, whilst AChE inhibiting activity was found only in a few sponges and was generally weak, except in the methanolic extract of T. ophiraphidites.

  6. PHYTOCHEMICAL SCREENING AND IN VITRO ANTIOXIDANT ACTIVITY OF AQUEOUS AND HYDROALCOHOLIC EXTRACT OF BACOPA MONNIERI LINN.

    Directory of Open Access Journals (Sweden)

    Monic Shah et al

    2012-09-01

    Full Text Available The present study was undertaken to investigate in-vitro antioxidant activity of aqueous and hydroalcoholic extract of whole plant of Bacopa monnieri Linn. Family- Scrophularaceae. The total Phenolic content was determined using folin ciocalteau method while the total flavonoid content was determined using aluminium chloride method. In vitro antioxidant activity was evaluated using the Reducing power assay, Hydrogen peroxide scavenging assay, nitric oxide scavenging activity, superoxide scavenging activity and hydroxyl radical scavenging activity. The hydroalcoholic extract had more phenol concentration (116.1 mg/g of extract when compared to aqueous extract (58 mg/g of extract. The flavonoid content was more in hydroalcoholic extract (242.6 mg/g of extract when compared to that of aqueous extract (202.8 mg/g of extract. The reducing power and hydrogen peroxide scavenging of the extract was found to be concentration dependent. The nitric oxide scavenging activity, superoxide scavenging activity and Hydroxyl radical scavenging activity was also concentration dependent with IC50 value being 254.70 µg/ml , 934.06 µg/ml and 510.60 µg/ml respectively for Aqueous extract and 169.22 µg/ml, 495.83 µg/ml, 488 µg/ml respectively for hydroalcoholic extract. The order of the antioxidant potency of the whole plant extract is Hydroalcoholic >> aqueous. The results clearly indicate that aqueous and hydroalcoholic extract of Bacopa monnieri has anti oxidant property which may be due to the presence of phenols and flavonoids.

  7. Removal of methyl orange from aqueous solution by Azolla filicoloides: Synthesis of Fe3O4 nano-particles and its surface modification by the extracted pectin of Azolla

    Institute of Scientific and Technical Information of China (English)

    Roohan Rakhshaee; Masoud Giahi; Afshin Pourahmad

    2011-01-01

    The modified Fe3O4 nano-particles with the extracted pectin from the cell wall of Azolla filicoloides (FN-EP) can remove methyl orange as a water-soluble azo dye from waste water better than Azolla and the extracted pectin from Azolla (EPA), alone. It could be due to more crowding the main functional groups of uptake after binding pectin with nano-particles. Thermodynamic studies showed that adsorption equilibrium constant (KL) and maximum adsorption capacities (Qmax) were increased with decreasing temperature (exothermic). The maximum uptake capacity (Qmax) of dye by FN-EP in a batch reactor was 0.533, 0.498 and 0.446 mmol/g at 5, 25 and 50 ℃, respectively. The enthalpy change (AH) and entropy change (△S) were -15.31 kJ/mol and -0.02434 kJ/mol K, respectively.

  8. Antihypertensive Effect of an Aqueous Extract of Passiflora nepalensis Wall

    Directory of Open Access Journals (Sweden)

    S S Patel

    2011-06-01

    Full Text Available Summary: The present study was designed to investigate the antihypertensive effect of an aqueous extract of the whole plant of Passiflora nepalensis wall (APN in renal hypertensive rats. Hypertension in experimental animals was induced by renal ischemia and reperfusion (IR. The blood pressure, pulse pressure and heart rate fell dose-dependently in renal hypertensive and normotensive rats after intravenous administration of 80, 160 and 320 mg/kg APN, suggesting that APN possesses antihypertensive, hypotensive and negative chronotropic effects. Renal IR significantly increased the levels of thio-barbituric acid reactive substances and reduced the levels of superoxide dismutase, catalase, and glutathione peroxidase (p<0.001 versus control in kidney, which was altered after intravenous administration of 160 and 320 mg/kg of APN, suggesting that APN protect kidney from IR injury (p<0.001 versus renal IR. Histological evaluation showed that renal IR increased, whereas APN decreased the focal glomerular necrosis, degeneration of tubular epithelium, necrosis in tubular epithelium, interstitial inflammatory infiltration, and congestion of blood vessels.   Industrial relevance: Herbal medicines are getting more importance in the treatment of high blood pressure because the modern synthetic medicines have side effects. A large proportion of the Indian population for their physical and psychological health needs depend on traditional system of medicine. Medicinal plants have become the focus of intense study in term of conservation as to whether their traditional uses are supported by actual pharmacological effects or merely based on folklore. Herbal medicines are free from side effects and less costly when compared to synthetic drugs. The present study will help the industry to produce herbal drugs with fewer side effects, which are affordable and more effective in the treatment of hypertension.

  9. Mineralization of paracetamol in aqueous solution with advanced oxidation processes.

    Science.gov (United States)

    Torun, Murat; Gültekin, Özge; Şolpan, Dilek; Güven, Olgun

    2015-01-01

    Paracetamol is a common analgesic drug widely used in all regions of the world more than hundred tonnes per year and it poses a great problem for the aquatic environment. Its phenolic intermediates are classified as persistent organic pollutants and toxic for the environment as well as human beings. In the present study, the irradiation of aqueous solutions of paracetamol with 60Co gamma-rays was examined on a laboratory scale and its degradation path was suggested with detected radiolysis products. The synergic effect of ozone on gamma-irradiation was investigated by preliminary ozonation before irradiation which reduced the irradiation dose from 5 to 3 kGy to completely remove paracetamol and its toxic intermediate hydroquinone from 6 to 4 kGy as well as increasing the radiation chemical yield (Gi values 1.36 and 1.66 in the absence and presence of ozone, respectively). The observed amount of formed hydroquinone was also decreased in the presence of ozone. There is a decrease in pH from 6.4 to 5.2 and dissolved oxygen consumed, which is up to 0.8 mg l(-1), to form some peroxyl radicals used for oxidation. Analytical measurements were carried out with gas chromatography/mass spectrometry and ion chromatography (IC) both qualitatively and quantitatively. Amounts of paracetamol and hydroquinone were measured with gas chromatography after trimethylsilane derivatization. Small aliphatic acids, such as acetic acid, formic acid and oxalic acid, were measured quantitatively with IC as well as inorganic ions (nitrite and nitrate) in which their yields increase with irradiation.

  10. Ultrasound assisted enzymatic depolymerization of aqueous guar gum solution.

    Science.gov (United States)

    Prajapat, Amrutlal L; Subhedar, Preeti B; Gogate, Parag R

    2016-03-01

    The present work investigates the effectiveness of application of low intensity ultrasonic irradiation for the intensification of enzymatic depolymerization of aqueous guar gum solution. The extent of depolymerization of guar gum has been analyzed in terms of intrinsic viscosity reduction. The effect of ultrasonic irradiation on the kinetic and thermodynamic parameters related to the enzyme activity as well as the intrinsic viscosity reduction of guar gum using enzymatic approach has been evaluated. The kinetic rate constant has been found to increase with an increase in the temperature and cellulase loading. It has been observed that application of ultrasound not only enhances the extent of depolymerization but also reduces the time of depolymerization as compared to conventional enzymatic degradation technique. In the presence of cellulase enzyme, the maximum extent of depolymerization of guar gum has been observed at 60 W of ultrasonic rated power and ultrasonic treatment time of 30 min. The effect of ultrasound on the kinetic and thermodynamic parameters as well as the molecular structure of cellulase enzyme was evaluated with the help of the chemical reaction kinetics model and fluorescence spectroscopy. Application of ultrasound resulted in a reduction in the thermodynamic parameters of activation energy (Ea), enthalpy (ΔH), entropy (ΔS) and free energy (ΔG) by 47%, 50%, 65% and 1.97%, respectively. The changes in the chemical structure of guar gum treated using ultrasound assisted enzymatic approach in comparison to the native guar gum were also characterized by FTIR. The results revealed that enzymatic depolymerization of guar gum resulted in a polysaccharide with low degree of polymerization, viscosity and consistency index without any change in the core chemical structure which could make it useful for incorporation in food products.

  11. Ion aggregation in high salt solutions. III. Computational vibrational spectroscopy of HDO in aqueous salt solutions

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Jun-Ho; Lim, Sohee; Chon, Bonghwan; Cho, Minhaeng, E-mail: mcho@korea.ac.kr [Center for Molecular Spectroscopy and Dynamics, Institute for Basic Science, Seoul 136-713 (Korea, Republic of); Department of Chemistry, Korea University, Seoul 136-713 (Korea, Republic of); Kim, Heejae; Kim, Seongheun [Department of Chemistry, Korea University, Seoul 136-713 (Korea, Republic of)

    2015-05-28

    The vibrational frequency, frequency fluctuation dynamics, and transition dipole moment of the O—D stretch mode of HDO molecule in aqueous solutions are strongly dependent on its local electrostatic environment and hydrogen-bond network structure. Therefore, the time-resolved vibrational spectroscopy the O—D stretch mode has been particularly used to investigate specific ion effects on water structure. Despite prolonged efforts to understand the interplay of O—D vibrational dynamics with local water hydrogen-bond network and ion aggregate structures in high salt solutions, still there exists a gap between theory and experiment due to a lack of quantitative model for accurately describing O—D stretch frequency in high salt solutions. To fill this gap, we have performed numerical simulations of Raman scattering and IR absorption spectra of the O—D stretch mode of HDO in highly concentrated NaCl and KSCN solutions and compared them with experimental results. Carrying out extensive quantum chemistry calculations on not only water clusters but also ion-water clusters, we first developed a distributed vibrational solvatochromic charge model for the O—D stretch mode in aqueous salt solutions. Furthermore, the non-Condon effect on the vibrational transition dipole moment of the O—D stretch mode was fully taken into consideration with the charge response kernel that is non-local polarizability density. From the fluctuating O—D stretch mode frequencies and transition dipole vectors obtained from the molecular dynamics simulations, the O—D stretch Raman scattering and IR absorption spectra of HDO in salt solutions could be calculated. The polarization effect on the transition dipole vector of the O—D stretch mode is shown to be important and the asymmetric line shapes of the O—D stretch Raman scattering and IR absorption spectra of HDO especially in highly concentrated NaCl and KSCN solutions are in quantitative agreement with experimental results. We

  12. Direct extraction of genomic DNA from maize with aqueous ionic liquid buffer systems for applications in genetically modified organisms analysis.

    Science.gov (United States)

    Gonzalez García, Eric; Ressmann, Anna K; Gaertner, Peter; Zirbs, Ronald; Mach, Robert L; Krska, Rudolf; Bica, Katharina; Brunner, Kurt

    2014-12-01

    To date, the extraction of genomic DNA is considered a bottleneck in the process of genetically modified organisms (GMOs) detection. Conventional DNA isolation methods are associated with long extraction times and multiple pipetting and centrifugation steps, which makes the entire procedure not only tedious and complicated but also prone to sample cross-contamination. In recent times, ionic liquids have emerged as innovative solvents for biomass processing, due to their outstanding properties for dissolution of biomass and biopolymers. In this study, a novel, easily applicable, and time-efficient method for the direct extraction of genomic DNA from biomass based on aqueous-ionic liquid solutions was developed. The straightforward protocol relies on extraction of maize in a 10 % solution of ionic liquids in aqueous phosphate buffer for 5 min at room temperature, followed by a denaturation step at 95 °C for 10 min and a simple filtration to remove residual biopolymers. A set of 22 ionic liquids was tested in a buffer system and 1-ethyl-3-methylimidazolium dimethylphosphate, as well as the environmentally benign choline formate, were identified as ideal candidates. With this strategy, the quality of the genomic DNA extracted was significantly improved and the extraction protocol was notably simplified compared with a well-established method.

  13. Study of the separation of zirconium and hafnium from nitric solutions by solvent extraction

    Energy Technology Data Exchange (ETDEWEB)

    Amaral, Janubia Cristina B.S.; Rocha, Laura R.T.; Morais, Carlos Antonio de, E-mail: jcbsa@cdtn.br, E-mail: lrtr@cdtn.br, E-mail: cmorais@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, BH (Brazil)

    2013-07-01

    This paper describes the study of the separation of Zr and Hf in nitric and hydrochloric media by solvent extraction technique. As aqueous phase, solutions prepared from the Zr and Hf hydroxides and the liquor generated from the product of the alkaline fusion of the zircon were used. The content of Zr and Hf in these solutions were 15 g/L and 0.6 g/L Hf respectively, and its acidity was varied between 1.0 and 10 mol/L. The effect of the acid extractants (DEHPA, IONQUEST®801 and CYANEX®272), solvating extractants (TBP and CYANEX®923) and basic extractants (PRIMENE®JTM, ALAMINE®336 and ALIQUAT®336), all of them diluted in dodecane, was investigated. In the solutions of the basic extractants, 5.0% of tridecanol was added as a modifier agent. Among the extractants investigated, the TBP in a nitric medium showed the best performance in the separation of the Zr/Hf. For acid extractants a high extraction was observed, however, with low selectivity. With the basic extractants no metals extraction was observed under the conditions investigated. The best results were obtained with the liquor generated from the product of alkaline fusion of zircon at acidity 7.0 mol/L and nitrate concentration of 9.2 mol/L. Under these conditions an extraction percentage of 91.6% for Zr and of 12.1% for Hf and a separation factor of Zr/Hf of 79.3 was obtained. (author)

  14. Relaxant activity of aqueous and ethanol extracts of parsley (Petroselinum crispum (Mill. Nym. ex A.W. Hill, Apiaceae on isolated ileum of rat

    Directory of Open Access Journals (Sweden)

    Branković Suzana

    2010-01-01

    Full Text Available Introduction. Parsley (Petroselinum crispum is used in the traditional herbal medicine to treat intestinal disorders. The aim of this study was to examine the effect of aqueous and ethanol extracts of parsley on spontaneous and acetylcholine induced contractions on isolated rat ileum. Material and methods. Wistar albino rats (250-300g were used in this study. The ileum portions were isolated out and cleaned off mesenteries. Preparations 2 cm long were mounted in 20 ml tissue baths containing Tyrode's solution maintained at 37ºC and aerated with a mixture of 5% carbon dioxide in oxygen. In the first part of experiments, contractile responses to the aqueous (ethanol extracts of parsley were recorded. In the second part, increasing concentrations of acetylcholine were added to the organ bath for a full concentration response curve and then concentration response curves were obtained after adding the aqueous (ethanol extracts of parsley. Results and discussion. Our results showed that aqueous (62.22±7.15% and ethanol (79.16±9.34% extracts of parsley in dose dependent manner decreased the tonus of spontaneous contractions of isolated rat ileum. The aqueous (32.16±2.75% and ethanol (53.96±4.86% extracts of parsley reduced the acetylcholine induced contraction, the reduction was greater with ethanol extract than with the aqueous one. Conclusion. It can be concluded that the aqueous and ethanol extracts of parsley exert antispasmodic activity on rat ileum. The relaxant effect of ethanol extract was better comparing to aqueous extract of parsley.

  15. Method for Non-Invasive Determination of Chemical Properties of Aqueous Solutions

    Science.gov (United States)

    Todd, Paul W. (Inventor); Jones, Alan (Inventor); Thomas, Nathan A. (Inventor)

    2016-01-01

    A method for non-invasively determining a chemical property of an aqueous solution is provided. The method provides the steps of providing a colored solute having a light absorbance spectrum and transmitting light through the colored solute at two different wavelengths. The method further provides the steps of measuring light absorbance of the colored solute at the two different transmitted light wavelengths, and comparing the light absorbance of the colored solute at the two different wavelengths to determine a chemical property of an aqueous solution.

  16. In vitro Antioxidant and Antibacterial Activity of Aqueous and Methanolic Extract of Mollugo nudicaulis Lam. Leaves

    Institute of Scientific and Technical Information of China (English)

    A Rameshkumar; TSivasudha

    2012-01-01

    Objective: To investigate invitro antioxidant activity, antibacterial activity and phytochemical screening of the aqueous and methanolic extract of Mollugo nudicaulis leaves (MN). Methods:The total phenolic and flavonoids content was quantified by Folin-Ciocalteu and Aluminum chloride method respectively. Invitro antioxidant activity was carried out by DPPH, ABTS and reducing power assays and antimicrobial activity was carried out by disc diffusion method.Results:The phytochemical tests of Mollugo nudicaulis revealed the presence of alkaloid steroids, flavonoids and reducing sugar in the both aqueous and methanolic extracts. Terpenoids were absent in both aqueous and methanolic extract of Mollugo nudicaulis. The total phenolics content of the methanolic and aqueous extract of leaves was 47.01 ± 0.8 and 46.4 ± 0.05 mg/100 g. The total flavonoid content was 41.3 ± 0.04 and 36.2 ± 0.01 mg/100 g respectively. The methanolic and aqueous extract of leaves showed IC50 values of DPPH radical scavenging as 48 and 190 μg/ml respectively. The IC50 values of ABTS radical scavenging for methanolic of aqueous extracts was 83 and 198.3 μg/ml of plant extract respectively. The total phenolics and flavonoids content and invitro antioxidant activity of methanolic extract was higher compared with aqueous extract. The methanolic extract of Mollugo nudicaulis used to determine antibacterial activity against bacterial species namely Pseudomonas aeruginosa, Proteus sp, Streptococcus sp, Entrobacter sp. Conclusion: This investigation suggests that the methanolic extracts of Mollugo nudicaulis possess potential antioxidant and antibacterial compounds.

  17. Thermodynamics of polyamide separation membrane in contact with aqueous solutions

    Science.gov (United States)

    Zhang, Xijing

    Composite reverse osmosis (RO) membranes, which are typically comprised of a polyamide active-layer that is formed by interfacial polymerization on a porous polysulfone support, are widely used in technologies for desalination and water purification. The water permeation and the rejection of salts or other contaminants are mainly determined by the transport properties of the polyamide active layer. Both the permeabilities of water and salt are described using solution-diffusion model and the mechanism of salt distribution in polyamide is distinguished into ion-exchange and ion partitioning. The ion partition coefficient κ in the active layer is a key thermodynamic parameter that partially controls the ability of the membrane to desalinate water. FT30 membranes are soaked in aqueous solutions of CsCl, KBr, or Na 2WO4, freeze-dried to remove water without disturbing ion distribution, and analyzed by Rutherford backscattering spectrometry. κ is calculated as ˜ 6 from the ion concentration in active layer measured using RBS and porosity in the polysulfone support layer is also derived as 40--50% from RBS data. Stress change induced by salt distribution is investigated with an optical system. Stress goes up to 9 MPa for transferred polyamide active layer from commercial RO membrane FT30 and 8 MPa for lab-synthesized polyamide film. The saturation in stress change is due to the pre-occupation of ions onto all the stress-related sites. The absorption of water in reverse osmosis membranes FT30 and LF10 is investigated by a combination of measurements of water mass uptake and biaxial stress as a function of relative humidity. Water solubility in polyamide active layer is 12 wt% at a relative humidity of 95%. The slope of a water concentration versus humidity curve can be used to calculate inter-diffusivity of water in polyamide active layers. By combining the measurements of water mass uptake and biaxial stress, we estimate the specific volume of water in the active

  18. In vitro vasodilatory effect of aqueous leaf extract of Thymus serrulatus on thoracic aorta of Guinea pigs

    Institute of Scientific and Technical Information of China (English)

    Bekesho; Geleta; Mebrahtu; Eyasu; Selamu; Kebamo; Asfaw; Debella; Eyasu; Makonnen; Abiy; Abebe

    2015-01-01

    Objective:To investigate the vasodilatory effecl of Thymus serrulatus(T.serrulatus) aqueous leaf extract on KCl(high K~+.80 mmol/L) induced precontracted isolated thoracic aorta rings on guinea pigs and the role of aorta endothelium on this action.Methods:Guinea pig thoracic aorta was removed and placed in an organ bath containing Krebs-Henseleit solution and aorta contractions were recorded isometrically.Results:The results revealed that T.serrulalus aqueous leaf extract(0.5-5 mg/mL)significantly(P<0.001) reduced KCl-induced contractions of guinea pig thoracic aorta in both intact(n=5) and denuded(n=5) endothelium in a concentration dependent manner,and the vasodilatory effect of the extract on intact endothelium was significantly(P<0.05) higher than that on denuded endothelium.Glibenclamide(10 μmol/L) significantly(P<0.001) increased the vasodilatory effect of extract in intact endothelium as compared to methylene blue(10μmol/L).atropine(10 μmol/L) and indomethacin(10 μmol/L).The effecl was more obvious on intact than that on denuded endothelium.Conclusions:The present findings demonstrate that T.serrulalus aqueous leaf extract has vasodilator)’ activity which might result in antihypertensive effect and its vasodilatory effect is endothelium-dependent.This might support the traditional claim of the plant in hypertensive.

  19. Kinetics of the decomposition and the estimation of the stability of 10% aqueous and non-aqueous hydrogen peroxide solutions

    Directory of Open Access Journals (Sweden)

    Zun Maria

    2014-12-01

    Full Text Available In this study, the stability of 10% hydrogen peroxide aqueous and non-aqueous solutions with the addition of 6% (w/w of urea was evaluated. The solutions were stored at 20°C, 30°C and 40°C, and the decomposition of hydrogen peroxide proceeded according to first-order kinetics. With the addition of the urea in the solutions, the decomposition rate constant increased and the activation energy decreased. The temperature of storage also affected the decomposition of substance, however, 10% hydrogen peroxide solutions prepared in PEG-300, and stabilized with the addition of 6% (w/w of urea had the best constancy.

  20. Laser-induced photoelectrochemistry: scavenging of photoemitted electrons in aqueous and non-aqueous solutions by electroactive organic species

    Energy Technology Data Exchange (ETDEWEB)

    Richardson, J.H. (Lawrence Livermore Lab., CA); Kovalenko, L.J.; Deutscher, S.B.; Harrar, J.E.; Perone, S.P.

    1980-01-01

    Photoemission current at a mercury electrode has been characterized electrochemically for aqueous solutions of methyl viologen, the disodium salt of anthraquinone-1,5-disulfonic acid, hydroquinone, p-benzoquinone, and chlorophyllin, and in DMF solutions of N/sub 2/O and anthraquinone. The scavenging species could be determined by comparing photoemission current-voltage curves with polarographic and cyclic voltammetric data. 11 figures.

  1. Histopathological changes in Wistar albino rats exposed to aqueous extract of unripe Carica papaya

    Directory of Open Access Journals (Sweden)

    Taofeeq Oduola

    2010-05-01

    Full Text Available Background: Exposure of animals to xenobiotics may or may not trigger adverse response at cellular levels. Aqueous extract of unripe Carica papaya is consumed by sickle cell patients as antisickling agent in Western Nigeria. Aim: This study was undertaken to investigate the effects of Carica papaya on certain organs in Wister albino rats exposed to aqueous extract of unripe Carica papaya. Materials and Methods: Different doses of aqueous extract of unripe Carica papaya were administered orally daily for 42 days to six groups of rats. At the end of exposure, the animals were sacrificed and tissue sections were prepared from livers, kidneys, hearts and small intestines using standard techniques. Results: Histopathological results showed that no pathological changes were observed in tissue sections of experimental animals when compared with tissue sections of the same organs in control animals. Conclusion: No pathological changes were elicited in the organs of rats exposed to aqueous extract of unripe Carica papaya.

  2. Capparis spinosa L. aqueous extract evokes antidiabetic effect in streptozotocin-induced diabetic mice

    Directory of Open Access Journals (Sweden)

    Mohamed Eddouks

    2017-02-01

    Full Text Available Objective: As the aqueous extract of Capparis spinosa (CS possess antidiabetic effect, he present study aims to reveal the possible  mechanism of action of CS in diabetic mice.Materials and Methods: Both single and repeated oral administrations of aqueous extract of CS were performed in multi-low dose streptozotocin-induced (MLDS diabetic mice. Euglycemic hyperinsulinemic clamp was used in association with the endogenous glucose production (perfusion rate of 3-3H glucose to evaluate the effect of CS aqueous extract on insulin sensitivity.Results: Our study showed that aqueous extract of CS possess a potent hypoglycaemic activity in MLDS diabetic mice. Furthermore, the analysis perfusion of 3-3H glucose demonstrated  the parallel decrease of basal endogenous glucose production (EGP with the hypoglycaemic activity. EGP was lower in CS-Treated group when compared to the control group (p

  3. Hypoglycemic effect of aqueous extract of Ammi visnaga in normal and streptozotocin-induced diabetic rats.

    Science.gov (United States)

    Jouad, Hassan; Maghrani, Mhamed; Eddouks, Mohammed

    2002-01-01

    The effect of the aqueous extract of Ammi visnaga (Apiaceae) on blood glucose levels was investigated in fasting normal and streptozotocin-induced diabetic rats after single and repeated oral administration. The aqueous extract of Ammi visnaga (AV) at a dose of 20 mg/kg significantly reduced blood glucose in normal rats six hours after a single oral administration (P < 0.005) and nine days after repeated oral administration (P < 0.05). This hypoglycemic effect is more pronounced in streptozotocin (STZ) diabetic rats (P < 0.001). Acute toxicity (LD50) and general behavioural effects of an aqueous extract of AV fruits was studied in mice. The LD50 of intraperitoneal (i.p.) and oral administration was 3.6 and 10.1 g/kg, respectively. These findings suggest that the aqueous extract of AV possess significant hypoglycemic effect in both normal and STZ diabetic rats and support, therefore, its claimed clinical use by the Moroccan population.

  4. Efficient Removal of Ruthenium Byproducts from Olefin Metathesis Products by Simple Aqueous Extraction

    Science.gov (United States)

    Hong, Soon Hyeok; Grubbs, Robert H.

    2008-01-01

    Simple aqueous extraction removed ruthenium byproducts efficiently from ring-closing metathesis (RCM) reactions catalyzed by a PEG-supported N-heterocyclic carbene-based ruthenium complex. PMID:17428062

  5. Preparation of CdTe nanocrystal-polymer composite microspheres in aqueous solution by dispersing method

    Institute of Scientific and Technical Information of China (English)

    LI Minjie; WANG Chunlei; HAN Kun; YANG Bai

    2005-01-01

    Highly fluorescent CdTe nanocrystals were synthesized in aqueous solution, and then processible CdTe nanocrystal-polymer composites were fabricated by coating the aqueous nanocrystals with copolymers of styrene and octadecyl-p-vinyl-benzyldimethylammonium chloride (SOV- DAC) directly. A dichloromethane solution of CdTe nano- crystal-polymer composites was dispersed in the aqueous solution of poly (vinyl alcohol) (PVA) generating highly fluorescent microspheres. Experimental parameters such as the concentration of nanocrystal-polymer composites, the concentration of PVA, and stirring speed which had important effect on the preparation of the microspheres were investigated in detail with fluorescent microscope characterization.

  6. Formation and disappearance of superoxide radicals in aqueous solutions. [79 references

    Energy Technology Data Exchange (ETDEWEB)

    Allen, A O; Bielski, B H.J.

    1980-01-01

    A literature review of superoxide radicals in aqueous solutions is presented covering the following: history; methods of formation of aqueous HO/sub 2//HO/sub 2//sup -/ by radiolysis and photolysis, electrolysis, mixing nonaqueous solutions into water, chemical reactions, enzymatic generation of O/sub 2//sup -/, and photosensitization; and properties of HO/sub 2//O/sub 2//sup -/ in aqueous solution, which cover spontaneous dismutation rates, pk and absorption spectra, catalyzed dismutation, thermodynamics and the so-called Haber-Weiss Reaction.

  7. Linear polymer aqueous solutions in soft lubrication:From boundary to mixed lubrication

    Institute of Scientific and Technical Information of China (English)

    LIU; ShuHai; TAN; GuiBin; WANG; DeGuo

    2013-01-01

    In order to better understand linear polymer aqueous solutions in soft lubrication from boundary to mixed lubrication,poly(ethylene glycol) and sodium hyaluronateare used as model polymers were investigated by using UMT-2 tribometer with the ball-on-disk mode. The relationship between the master Stribeck curves of the polymer aqueous solutions and the influence factors were investigated. Experimental results indicated that soft lubrication is determined by lubricant rheological properties and surface-lubricant interactions, e.g., wetting behavior of polymer aqueous solution on tribological surfaces.

  8. Hydrate phase equilibria of CO2+N2+aqueous solution of THF, TBAB or TBAF system

    DEFF Research Database (Denmark)

    Sfaxi, Imen Ben Attouche; Durand, Isabelle; Lugo, Rafael

    2014-01-01

    We report hydrate dissociation conditions of CO2 (15 and 30mol%)+N2 (85 and 70mol%) in the presence of aqueous solutions of THF, TBAB or TBAF. The concentrations of TBAB and TBAF in the aqueous solutions are 5wt% and 9wt% while THF concentration in aqueous solution is 3mol%. Two different...... experimental techniques including isochoric pressure search method and a DSC method are used to measure the hydrate dissociation conditions. A comparison is finally made with the literature data. It is expected that this study provides better understanding of hydrate phase equilibria associated with CO2...... capture. © 2014 Elsevier Ltd....

  9. DIURETIC AND ANTI-INFLAMMATORY ACTIVITY OF AQUEOUS EXTRACT OF AERVA SANGUINOLENTA (L.) BLUME

    OpenAIRE

    Srinivas Reddy K; Rajeev Reddy E; Ganapaty S

    2011-01-01

    The study was designed to evaluate the diuretic and anti-inflammatory potency of aqueous extract of whole plant of Aerva sanguinolenta in wistar albino rats. Different parameters viz. total urine volume, urine concentration of electrolytes such as sodium; potassium and chloride have been evaluated for assessment of diuretic activity. Anti-inflammatory was performed against carrageenan induced paw oedema method by using indomethacin as standard.The results revealed that the aqueous extract sho...

  10. Antinociceptive and anti-inflammatory effects of aqueous extract of Chenopodium opulifolium schrad leaves

    Science.gov (United States)

    Ajayi, Abayomi M.; Tanayen, Julius Khidzee; Magomere, Albert; Ezeonwumelu, Joseph O. C.

    2017-01-01

    Aim: Chenopodium opulifolium is a specie of the Chenopodiaceae commonly used as vegetables in local diet and for treating different ailment in Uganda. This study was conducted to evaluate the antioxidant, antinociceptive and anti-inflammatory effects of the aqueous extract of C. opulifolium leaves (AECO). Materials and Methods: The dried leaf of the plant was extracted by maceration in water. Qualitative and quantitative phytochemical analysis, antioxidants, and membrane stabilizing effects were determined in the extract. The extract was then investigated for acute toxicity, antinociceptive (writhing, hot plate and open field test), and anti-inflammatory (egg albumin-induced paw edema) effects in rodents. Results: Phytochemical analysis revealed the presence of alkaloids, tannins, phlobatannins, flavonoids, and saponins in AECO. Total caffeic acid derivatives and total flavonoids content were 91.7 mgCAE/g sample and 94.7 mgRE/g sample, respectively. AECO demonstrated antioxidant effects in both 1,1-diphenyl-2-picryl-hydrazyl and NO assays. Significant membrane stabilizing activity was observed in both the heat and hypotonic solution-induced lysis of erythrocytes. The acute toxicity test showed that AECO (5000 mg/kg) did not cause any significant change in behavior or death in rats. AECO (100-400 mg/kg) produced a significant antinociceptive effect in both the writhing and hot plate tests, but no significant reduction in the locomotory activity in mice. Furthermore, the extract significantly (P < 0.05) reduced egg albumin-induced rat paw edema by 44.2%, 44.5%, and 51.2%, respectively, after 120 min. Conclusion: The results showed that C. opulifolium extract possesses significant antioxidant, antinociceptive and anti-inflammatory effects, and these affirm the reasons for its folkloric use. PMID:28163955

  11. Photophysical properties of betaxanthins: Vulgaxanthin I in aqueous and alcoholic solutions

    Energy Technology Data Exchange (ETDEWEB)

    Wendel, Monika [Quantum Electronics Laboratory, Faculty of Physics, Adam Mickiewicz University in Poznan, Umultowska 85, Poznan 61-614 (Poland); Szot, Dominika; Starzak, Karolina; Tuwalska, Dorota [Faculty of Chemical Engineering and Technology, Institute C-1, Section of Analytical Chemistry, Cracow University of Technology, Warszawska 24, Cracow 31-155 (Poland); Gapinski, Jacek [Molecular Biophysics Department, Faculty of Physics, Adam Mickiewicz University in Poznan, Umultowska 85, Poznan 61-614 (Poland); Naskrecki, Ryszard [Quantum Electronics Laboratory, Faculty of Physics, Adam Mickiewicz University in Poznan, Umultowska 85, Poznan 61-614 (Poland); Prukala, Dorota; Sikorski, Marek [Faculty of Chemistry, Adam Mickiewicz University in Poznan, Umultowska 89b, Poznan 61-614 (Poland); Wybraniec, Slawomir [Faculty of Chemical Engineering and Technology, Institute C-1, Section of Analytical Chemistry, Cracow University of Technology, Warszawska 24, Cracow 31-155 (Poland); Burdzinski, Gotard, E-mail: gotardb@amu.edu.pl [Quantum Electronics Laboratory, Faculty of Physics, Adam Mickiewicz University in Poznan, Umultowska 85, Poznan 61-614 (Poland)

    2015-11-15

    Betaxanthins are yellow pigments present in Caryophyllales plants and some higher fungi. We characterize photophysical properties of vulgaxanthin I and extracts of Amanita muscaria L. Vulgaxanthin I photoexcitation at λ{sub exc}=476 nm leads to the S{sub 1} excited state with the S{sub 1}→S{sub n} absorption bands at ca. 390 and 920 nm in both aqueous and alcoholic solutions. The S{sub 1} state lifetimes (2.9 and 37 ps in water) imply that vulgaxanthin I exists in two stereoisomeric forms. An increase in the solvent viscosity extends the S{sub 1} lifetimes and fluorescence quantum yields, probably due to hindered internal rotations in the dye. Internal conversion is the major S{sub 1} state deactivation path, with fluorescence being a minor channel, and S{sub 1}→T{sub 1} intersystem crossing not observed. Betaxanthins extracted from A. muscaria L. have similar properties. Efficient dissipation of the absorbed light energy as heat supports the postulate of photoprotective role of betaxanthins in vivo. - Highlights: • Betaxanthin S{sub 1} state deactivation mechanism is mainly radiationless. • S{sub 1} state shows absorption band with maxima at about 390 nm and 920 nm. • Solvent viscosity affects S{sub 1} state lifetime and fluorescence quantum yield. • Addition of potassium iodide to solution enhances ISC in betaxanthin.

  12. Perstraction of intracellular pigments by submerged cultivation of Monascus in nonionic surfactant micelle aqueous solution.

    Science.gov (United States)

    Hu, Zhiqiang; Zhang, Xuehong; Wu, Zhenqiang; Qi, Hanshi; Wang, Zhilong

    2012-04-01

    "Milking processing" describes the cultivation of microalgae in a water-organic solvent two-phase system that consists of simultaneous fermentation and secretion of intracellular product. It is usually limited by the conflict between the biocompatibility of the organic solvent to the microorganisms and the ability of the organic solvent to secret intracellular product into its extracellular broth. In the present work, submerged cultivation of Monascus in the nonionic surfactant Triton X-100 micelle aqueous solution for pigment production is exploited, in which the fungus Monascus remains actively growing. Permeabilization of intracellular pigments across the cell membrane and extraction of the pigments to the nonionic surfactant micelles of its fermentation broth occur simultaneously. "Milking" the intracellular pigments in the submerged cultivation of Monascus is a perstraction process. The perstractive fermentation of intracellular pigments has the advantage of submerged cultivation by secretion of the intracellular pigments to its extracellular broth and the benefit of extractive microbial fermentation by solubilizing the pigments into nonionic surfactant micelles. It is shown as the marked increase of the extracellular pigment concentration by the submerged cultivation of Monascus in the nonionic surfactant Triton X-100 micelle solution.

  13. Study on Gold(Ⅰ) Solvent Extraction from Alkaline Cyanide Solution by TBP with Addition of Surfactant

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    The new solvent extraction system for gold(Ⅰ) from alkaline cyanide solution by TBP with addition of surfactant in aqueous phase was studied. The effect of various factors, such as equilibrium pH, constitution of organic phase, molar ratio of CPB∶Au(CN)2-, extraction time, aqueous/organic phase ratio, different initial gold concentration, equilibrium temperature, different diluent, different types of extractants and surfactants etc., was inspected. The results show that gold(Ⅰ) can be extracted quantitatively by controlling the quantity of surfactant (CPB); both the equilibrium pH and diluent hardly influence percent extraction. Gold(Ⅰ) percent extraction reaches more than 98% under the optimal experimental conditions. 30% vol TBP diluted by sulphonating kerosene can load gold(Ⅰ) to rather high levels. Loading capacity is in excess of 38 g/L. The extraction mechanism is discussed and the overall extraction reaction is deduced.

  14. Syringa oblata Lindl. Aqueous Extract Is a Potential Biofilm Inhibitor in S. suis

    Science.gov (United States)

    Bai, Jingwen; Yang, Yanbei; Wang, Shuai; Gao, Lingfei; Chen, Jianqing; Ren, Yongzhi; Ding, Wenya; Muhammad, Ishfaq; Li, Yanhua

    2017-01-01

    Streptococcus suis (S. suis) is a zoonotic pathogen that causes severe disease symptoms in pigs and humans. Syringa oblata Lindl. distributed in the middle latitudes of Eurasia and North America were proved as the most development potential of Chinese Medicine. In this study, biofilm formation by S. suis decreased after growth with 1/2 MIC, 1/4 MIC, or 1/8 MIC of Syringa oblata Lindl. aqueous extract and rutin. Scanning electron microscopy analysis revealed the potential effect of Syringa oblata Lindl. aqueous extract and rutin against biofilm formation by S. suis. Using iTRAQ technology, comparative proteomic analyses was performed at two conditions: 1/2 MIC of Syringa oblata Lindl. aqueous extract treated and non-treated cells. The results revealed the existence of 28 proteins of varying amounts. We found that the majority of the proteins were related to cell growth and metabolism. We also found that Syringa oblata Lindl. Aqueous extract affected the synthesis enzymes. In summary, Syringa oblata Lindl. aqueous extract might be used to inhibit the biofilm formation effectively by S. suis, and the active ingredients of the Syringa oblate Lindl. aqueous extract is rutin. The content of rutin is 9.9 ± 0.089 mg/g dry weight. PMID:28194111

  15. Persistence of two neonicotinoid insecticides in wastewater, and in aqueous solutions of surfactants and dissolved organic matter.

    Science.gov (United States)

    Peña, A; Rodríguez-Liébana, J A; Mingorance, M D

    2011-07-01

    Wastewater treatment plants receive organic contaminants, such as pesticides, which reach the sewage system from domestic, industrial or agricultural activities. In wastewater, which is a complex mixture of organic and inorganic compounds, biotic or abiotic degradation of contaminants can be affected by the presence of co-solutes. The photodecomposition in natural sunlight of two neonicotinoid insecticides, thiamethoxam and thiacloprid, was investigated in wastewater, aqueous extracts of sewage sludge and in aqueous surfactant solutions, which are abundant in wastewater. Dissipation in the dark was also studied in wastewater, due to reduction of transmitted sunlight in wastewater ponds. With regard to photolysis, thiamethoxam degraded rapidly in all the aqueous solutions. Among them sewage sludge extracts slightly modified (average half-life 17.6h), wastewater increased (13.7h) and non-ionic surfactants led, as a family, to the highest dissipation rates (average 6.2h), with respect to control water (18.7h). Additionally this pesticide also underwent a slower biodegradation process in wastewater in the dark under anaerobic conditions (around 25d). A metabolite of thiamethoxam from the biological decomposition in wastewater was identified by HPLC/MS. On the other hand thiacloprid was found to be resistant to photo- and biodecomposition and remained almost unchanged during the experimental periods in all the tested media.

  16. Cryo-irradiation as a terminal method for the sterilization of drug aqueous solutions.

    Science.gov (United States)

    Maquille, Aubert; Habib Jiwan, Jean-Louis; Tilquin, Bernard

    2008-05-01

    The aim of this study is to evaluate the specificities of the irradiation of drugs in frozen aqueous solution. The structures of the degradation products were determined to gain insight into the radiolysis mechanisms occurring in frozen aqueous solutions. Metoclopramide hydrochloride and metoprolol tartrate were chosen as models. The frozen solutions were irradiated at dry ice temperature by high energy electrons at various doses. The drug purity (chemical potency) and the radiolysis products were quantified by HPLC-DAD. Characterization of the degradation products was performed by LC-APCI-MS-MS. The structures of the radiolysis products detected in irradiated frozen aqueous solutions were compared to those detected in solid-state and aqueous solutions (previous studies). For both metoclopramide and metoprolol, solute loss upon irradiation of frozen aqueous solutions was negligible. Five radiolysis products present in traces were identified in irradiated metoclopramide frozen solutions. Three of them were previously identified in solid-state irradiated metoclopramide crystals. The two others were formed following reactions with the hydroxyl radical (indirect effect). Only one fragmentation product was observed in irradiated metoprolol frozen solutions. For both drugs, radiosterilization of frozen solutions, even at high doses (25 kGy), was found to be possible.

  17. 1,3-DIPOLAR CYCLOADDITION OF PHENYL AZIDE TO NORBORNENE IN AQUEOUS-SOLUTIONS

    NARCIS (Netherlands)

    Wijnen, J.W; Steiner, R.A.; Engberts, J.B.F.N.

    1995-01-01

    Second-order rate constants for the cycloaddition of phenyl azide to norbornene were determined in aqueous solutions. In organic solvents this reaction shows a very small solvent effect. In highly aqueous media, however, remarkable accelerations are observed. The solvent dependence of the rate const

  18. Green synthesis of silver nanoparticles with antibacterial activities using aqueous Eriobotrya japonica leaf extract

    Science.gov (United States)

    Rao, Bo; Tang, Ren-Cheng

    2017-03-01

    An eco-friendly approach for the preparation of silver nanoparticles (AgNPs) from silver nitrate solution using aqueous Eriobotrya japonica leaf extract was investigated. The reduction of silver ions in solution was monitored using UV–visible absorption spectroscopy, and the surface plasmon resonance of AgNPs at 435 nm was observed. The proper condition to biosynthesize AgNPs using E. japonica leaf extract was optimized by UV–visible absorption spectroscopy and dynamic light scattering measurement (DLS). The biosynthesised nanoparticles were characterised using transmission electron microscopy (TEM), scanning electron microscopy (SEM), energy dispersive x-ray spectroscopy (EDX), DLS, x-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). XRD and EDX analyses confirmed the crystalline character of AgNPs and the presence of elemental silver. The prepared AgNPs were spherical in shape, and their average particle size determined by TEM was about 20 nm. Furthermore the AgNPs were found to exhibit effective antibacterial activities against Escherichia coli and Staphylococcus aureus.

  19. Integration of carboxyl modified magnetic particles and aqueous two-phase extraction for selective separation of proteins.

    Science.gov (United States)

    Gai, Qingqing; Qu, Feng; Zhang, Tao; Zhang, Yukui

    2011-07-15

    Both of the magnetic particle adsorption and aqueous two-phase extraction (ATPE) were simple, fast and low-cost method for protein separation. Selective proteins adsorption by carboxyl modified magnetic particles was investigated according to protein isoelectric point, solution pH and ionic strength. Aqueous two-phase system of PEG/sulphate exhibited selective separation and extraction for proteins before and after magnetic adsorption. The two combination ways, magnetic adsorption followed by ATPE and ATPE followed by magnetic adsorption, for the separation of proteins mixture of lysozyme, bovine serum albumin, trypsin, cytochrome C and myloglobin were discussed and compared. The way of magnetic adsorption followed by ATPE was also applied to human serum separation.

  20. Pulse radiolysis of tetrazolium violet in aqueous and aqueous-alcoholic solutions under oxidative and reductive conditions

    Energy Technology Data Exchange (ETDEWEB)

    Kovacs, A. [Institute of Isotopes, Hungarian Academy of Sciences, P.O. Box 77, H-1525 Budapest (Hungary)], E-mail: akovacs@iki.kfki.hu; Wojnarovits, L.; Palfi, T. [Institute of Isotopes, Hungarian Academy of Sciences, P.O. Box 77, H-1525 Budapest (Hungary); Emi-Reynolds, G. [Radiation Protection Institute, Ghana Atomic Energy Commission, P.O. Box LG 80, Legon-Accra (Ghana); Fletcher, J. [Department of Physics, University of Cape Coast, Cape Coast (Ghana)

    2008-09-15

    The radiolytic reduction of colourless tetrazolium salts to coloured formazans in liquid and solid state is suggested for dosimetry purposes. In order to clarify the reaction mechanism, a pulse radiolysis study was conducted in aqueous and aqueous-alcoholic solutions under oxidative and reductive conditions. Under reducing conditions, fast formation of the electron adduct tetrazolinyl radical was observed: coloured formazan final product formed during the decay of electron adduct. Both the decay of the tetrazolinyl radical and the formation of the formazan were found to be second order. The spectra of the formazan were similar in neutral and alkaline solutions, but with higher absorbance in the latter solutions due to the higher molar absorption coefficient. Under oxidative conditions formazan did not form; hydroxylated products through OH-adducts were observed in the pH range studied.

  1. Pulse radiolysis of tetrazolium violet in aqueous and aqueous-alcoholic solutions under oxidative and reductive conditions

    Science.gov (United States)

    Kovács, A.; Wojnárovits, L.; Pálfi, T.; Emi-Reynolds, G.; Fletcher, J.

    2008-09-01

    The radiolytic reduction of colourless tetrazolium salts to coloured formazans in liquid and solid state is suggested for dosimetry purposes. In order to clarify the reaction mechanism, a pulse radiolysis study was conducted in aqueous and aqueous-alcoholic solutions under oxidative and reductive conditions. Under reducing conditions, fast formation of the electron adduct tetrazolinyl radical was observed: coloured formazan final product formed during the decay of electron adduct. Both the decay of the tetrazolinyl radical and the formation of the formazan were found to be second order. The spectra of the formazan were similar in neutral and alkaline solutions, but with higher absorbance in the latter solutions due to the higher molar absorption coefficient. Under oxidative conditions formazan did not form; hydroxylated products through OH-adducts were observed in the pH range studied.

  2. Wound-healing potential of aqueous and ethanolic extracts of apamarga leaves

    Directory of Open Access Journals (Sweden)

    P K Ghosh

    2011-01-01

    Full Text Available The present research work was aimed at exploring the wound-healing activity of alcoholic and an aqueous Achyranthes aspera Linn (apamarga leaf extract. Leaf extracts (aqueous and ethanolic were examined for its wound-healing activity in the form of ointment (1% w/w in Excision model and Incision model in rats. The evaluation was made in terms of wound contractibility and wound closure time. A. aspera Linn leaf extract showed significant (P<0.001 wound-healing activity when compared with control and was as effective as soframycin (standard cream for comparison. The wound-healing potential of ethanolic extract was slightly more compared with aqueous extract. The present study showed the wound-healing potential of apamarga leaves.

  3. Effects of Aqueous Extract of Moringa Oleifera Linn on Alloxan Induced Hyperglycemia

    Directory of Open Access Journals (Sweden)

    Ruchi Singh

    2016-07-01

    Full Text Available The study determines the effect of aqueous extract of M. oleifera seeds with respect to its route of administration. The rats were divided into 4 groups. Group I-Rats received only rat chow and water. Group II- Rats received alloxan and were treated with 500mg/kg body weight after 2hours. Group III- Rats receiving alloxan after 2 hours were treated with aqueous extract of M. oleifera (500mg/kg body weight intraperitonially. Group IV- Rats receiving alloxan after 24 hours began receiving aqueous extract of M. oleifera seeds (500mg/kg body weight intraperitonially for 1 week. The result of the study showed a significant decrease in the blood glucose level after 12 hours and also after 7 days of both orally and intraperitonially with M. oleifera seed extract. This proves that M. oleifera seed extract have a hypoglycemic effect on both the mild and severe alloxan induced hyperglycemic rats.

  4. Aqueous two-phase system based on natural quaternary ammonium compounds for the extraction of proteins.

    Science.gov (United States)

    Zeng, Chao-Xi; Xin, Rui-Pu; Qi, Sui-Jian; Yang, Bo; Wang, Yong-Hua

    2016-02-01

    Aqueous two-phase systems, based on the use of natural quaternary ammonium compounds, were developed to establish a benign biotechnological route for efficient protein separation. In this study, aqueous two-phase systems of two natural resources betaine and choline with polyethyleneglycol (PEG400/600) or inorganic salts (K2 HPO4 /K3 PO4 ) were formed. It was shown that in the K2 HPO4 -containing aqueous two-phase system, hydrophobic interactions were an important driving force of protein partitioning, while protein size played a vital role in aqueous two-phase systems that contained polyethylene glycol. An extraction efficiency of more than 90% for bovine serum albumin in the betaine/K2 HPO4 aqueous two-phase system can be obtained, and this betaine-based aqueous two-phase system provided a gentle and stable environment for the protein. In addition, after investigation of the cluster phenomenon in the betaine/K2 HPO4 aqueous two-phase systems, it was suggested that this phenomenon also played a significant role for protein extraction in this system. The development of aqueous two-phase systems based on natural quaternary ammonium compounds not only provided an effective and greener method of aqueous two-phase system to meet the requirements of green chemistry but also may help to solve the mystery of the compartmentalization of biomolecules in cells.

  5. Selective extraction of zinc from sulfate leach solution of zinc ore

    Institute of Scientific and Technical Information of China (English)

    覃文庆; 蓝卓越; 黎维中; 邱冠周

    2003-01-01

    Selective extraction of zinc from sulfate leach solution of zinc ore was studied.D2EHPA dissolved in260# kerosene was used as extractant.The pH-extraction isotherms show the extraction order of D2EHPA for metals is Fe3+>Zn2+>Ca2+>Al3+>Mn2+>Cu2+>Cd2+>Co2+>Ni2+>Mg2+(pH0.5).This confirms that Fe3+ ispreferentially extracted before the extraction of zinc.Extraction experiments were carried out with varying the extractant content,equilibration time,aqueous pH and phase ratio,and the solvent extraction of zinc with sodium saltof D2EHPA were also investigated.Some impurity co-extracted into the zinc loaded organic phase was efficiently removed by scrub,and the Fe3+ was hardly stripped from organic phase by sulfuric acid,hence zinc was separatedfrom Fe3+ by selective stripping.A pregnant zinc sulfate solution with low contaminants was obtained by selectivesolvent extraction.

  6. Decomposition Studies of Triphenylboron, Diphenylborinic Acid and Phenylboric Acid in Aqueous Alkaline Solutions Containing Copper

    Energy Technology Data Exchange (ETDEWEB)

    Crawford, C.L. [Westinghouse Savannah River Company, AIKEN, SC (United States); Peterson, R. A.

    1997-02-11

    This report documents the copper-catalyzed chemical kinetics of triphenylboron, diphenylborinic acid and phenylboric acid (3PB, 2PB and PBA) in aqueous alkaline solution contained in carbon-steel vessels between 40 and 70 degrees C.

  7. Absorption of nitric oxide into aqueous solutions of ferrous chelates accompanied by instantaneous reaction

    NARCIS (Netherlands)

    Demmink, J.F; vanGils, I.C.F.; Beenackers, A.A C M

    1997-01-01

    The absorption of nitric oxide (NO) into aqueous solutions of ferrous chelates of nitrilotriacetic acid (NTA), ethylene diaminetetraacetic acid (EDTA), hydroxyethylenediaminetriacetic acid (HEDTA), and diethylenetriaminepentaacetic acid (DTPA) was studied in a stirred cell reactor. Experimental cond

  8. Thermodynamics of the complexation of arabinogalactan with salicylic and p-aminobenzoic acids in aqueous solutions

    Science.gov (United States)

    Mudarisova, R. Kh.; Badykova, L. A.

    2016-03-01

    The thermodynamics of complexation of arabinogalactan with salicylic and p-aminobenzoic acids in aqueous solutions is studied by means spectroscopy. The standard thermodynamic characteristics (Δ H°; Δ G°; Δ S°) of complexation are calculated.

  9. Probing regenerative potential of Moringa oleifera aqueous extracts using In vitro cellular assays

    Directory of Open Access Journals (Sweden)

    Evangeline E Fernandes

    2016-01-01

    Full Text Available Background: Molecules stimulating regeneration and proliferation of cells are of significance in combating ailments caused due to tissue injury, inflammation, and degenerative disorders. Moringa oleifera is one of the most valued food plants having the profile of important nutrients and impressive range of medicinal uses. Objective: To evaluate the potential of M. oleifera aqueous leaf and flower extracts to promote the proliferation of cells and explore their effect on cancer cell lines for assessment of safety. Materials and Methods: Aqueous leaf and flower extracts of M. oleifera were investigated for effect on rat-derived primary fibroblast, mesenchymal stem cells (MSCs, and cancer cell lines using cell proliferation assay. They were also tested and compared for wound healing, angiogenesis, and hepatoprotective effect using in vitro assays. Results: Statistically significant increase in the proliferation of primary rat fibroblast, MSCs, and angiogenesis was observed after treatment with aqueous flower extract. The aqueous leaf extract determined a comparatively moderate increment in the proliferation of MSCs and angiogenesis. It however showed prominent cytotoxicity to cancer cell lines and a significant hepatoprotective effect. Conclusion: A very clear difference in response of the two extracts to different types of cells was detected in this study. The aqueous flower extract exhibited a higher potential to stimulate cell proliferation while not exerting the same effect on cancer cell lines. The leaf extract on the other hand, had a prominent antitumor and hepatoptotective effects.

  10. Albendazole Solubilization in Aqueous Solutions of Nicotinamide: Thermodynamics and Solute Solvent Interactions

    Directory of Open Access Journals (Sweden)

    Sushree Tripathy

    2013-12-01

    Full Text Available The present study deals with experiments so as to highlight the solute (drug albendazole – solvent ( water interactions and related thermodynamic modifications in presence of the hydrotropic agent nicotinamide at different temperatures T (= 298.15 to 313.15K. Density and conductivity values of albendazole have been determined in water in (0.2, 0.4, 0.6, 0.8, 1 and 2 mol dm-3 aqueous solutions of nicotinamide at temperatures T(= 298.15, 303.15, 308.15 and 313.15K, where as solubility was studied at 308.15. A concentration dependent solubility enhancement of albendazole was observed. The solubility data was treated to obtain the concentration dependent solubilization efficiency and the Gibbs free energy of transfer (∆G0tr of albendazole from pure water to the solvent systems. From the density values, the limiting partial molar volumes and expansibilities have been calculated. The limiting molar conductance (L0 and Arrhenius activation energy (Es values have been calculated from the generated conductance values. The thermo physical parameters were discussed in terms of solute solvent interactions.

  11. Removal of Cadmium and Lead Ions from Aqueous Solution by Nanocrystalline Magnetite Through Mechanochemical Activation

    OpenAIRE

    Mohsen Hosseinzadeh; Seyyed Ali Seyyed Ebrahimi; Shahram Raygan; Seyed Morteza Masoudpanah

    2016-01-01

    In this study, the removal of cadmium and lead ions from aqueous solution by nanocrystalline magnetite was investigated. The nanocrystalline magnetite was synthesized by mechanochemical activation of hematite in a high energy planetary mill in argon atmosphere for 45 hours. The ability of the synthesized nanocrystalline magnetite for removal of Cd(II) and Pb(II) from aqueous solutions was studied in a batch reactor under different experimental conditions with different pHs, contact times, ini...

  12. Pervaporation of Aqueous Solution of Acetaldehyde Through ZSM-5 Filled PDMS Composite Membrane

    Institute of Scientific and Technical Information of China (English)

    伍艳辉; 谭惠芬; 李佟茗; 金源

    2012-01-01

    Hydrophobic ZSM-5 zeolite filled polydimethylsiloxane (PDMS) composite membranes with Nylon micro-filtration membrane as the support layer were prepared to separate acetaldehyde from its aqueous solution. The composite membranes were characterized by Fourier transform infrared spectroscopy and X-ray diffraction. Their structural morphology and thermal stability were also examined. The swelling study showed that the composite membranes presented higher degree of swelling in aqueous solution of acetaldehyde than in pure water at 25℃,

  13. Relation between the solubility of proteins in aqueous solutions and the second virial coefficient of the solution

    NARCIS (Netherlands)

    Haas, C; Drenth, J; Wilson, WW

    1999-01-01

    Tn recent publications it was pointed out that there is a correlation between the observed values of the solubility of proteins in aqueous solutions and the second virial coefficient of the solution. In this paper we give a theoretical explanation of this relation. The derived theoretical expression

  14. Oxidation of atrazine by photoactivated potassium persulfate in aqueous solutions

    Science.gov (United States)

    Khandarkhaeva, M. S.; Aseev, D. G.; Sizykh, M. R.; Batoeva, A. A.

    2016-11-01

    General laws of the photochemical oxidation of atrazine by inorganic peroxo compounds under the impact of solar radiation are studied. It is found that almost complete conversion of atrazine can be achieved via photochemical oxidation with persulfate after 120 min, but no deep mineralization is observed. The effect an aqueous matrix has on the processes of atrazine degradation in combined oxidation systems is considered.

  15. Characterization of trehalose aqueous solutions by neutron spin echo

    CERN Document Server

    Branca, C; Magazù, S; Maisano, G; Mangione, A; Pappas, C; Triolo, A

    2002-01-01

    The present work reports neutron spin-echo (NSE) results on aqueous mixtures of trehalose, a naturally occurring disaccharide of glucose, which shows an extraordinary bioprotective effectiveness against dehydration and freezing. The aim of the work is to furnish new results on the dynamics of the trehalose/water system on the nano- and picosecond scales. (orig.)

  16. Characterization of trehalose aqueous solutions by neutron spin echo

    Energy Technology Data Exchange (ETDEWEB)

    Branca, C.; Faraone, A.; Magazu' , S.; Maisano, G.; Mangione, A. [Dipartimento di Fisica and INFM, Universita di Messina, PO Box 55, 98166 Messina (Italy); Pappas, C.; Triolo, A. [Hahn-Meitner-Institut, BENSC (NI), Glienicker Strasse, 14109 Berlin (Germany)

    2002-07-01

    The present work reports neutron spin-echo (NSE) results on aqueous mixtures of trehalose, a naturally occurring disaccharide of glucose, which shows an extraordinary bioprotective effectiveness against dehydration and freezing. The aim of the work is to furnish new results on the dynamics of the trehalose/water system on the nano- and picosecond scales. (orig.)

  17. Kinetics of ozone-phenol reaction in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Joshi, M.G.; Shambaugh, R.L.

    1982-01-01

    The kinetics of the reaction of ozone and phenol in aqueous medium was studied. The reaction was first order with respect to both ozone and phenol. The rate constant was found to increase with increase in the pH of the reaction mixture. Four different catalysts were examined for their effect on the rate of reaction. 30 refs.

  18. Towards an understanding of solvent extraction--electroanalytical characterization of chloride-leaching solutions.

    Science.gov (United States)

    Paiva, A P; Abrantes, L M

    2001-08-01

    Solvent extraction has been employed to purify media simulating chloride-leaching solutions resulting from complex sulfide concentrate processing, and cyclic voltammetry (CV) has been chosen to characterize those hydrometallurgical aqueous phases. The possibilities of the CV technique were investigated by the evaluation of the adequacy of a specific organic extractant, triisobutylphosphine sulfide, aimed to efficiently and selectively extract silver from a complex chloride medium, additionally containing tenfold to 40-fold molar concentrations of iron, copper and lead. The influence of the oxidation state of the metallic ions present in the feed solution, namely Cu(II) and Cu(I), is considered. The possibilities of CV analysis for the characterization of stripping solutions are also illustrated.

  19. The use of bis (-2-ethylhexyl) phosphoric acid for the extraction of zinc from concentrated ammonium chloride solutions

    Energy Technology Data Exchange (ETDEWEB)

    Amer, S.; Luis, A.; Cuadra, A. de la; Caravaca, C.

    1994-01-01

    The extraction of zinc from concentrated ammonium chloride solutions by means of the bis(-2-ethylhexyl) phosphoric acid is studied. Mass balances and chemical equilibria relating the different chemical species in both phases are presented in order to establish a model describing the behaviour of the different species. Good agreement between experimental data and theoretical curves is obtained. A comparison of the zinc extraction from a strong complexing medium as that of concentrated ammonium chloride solutions with an uncomplexing zinc perchlorate solution is made, in order to see the influence of the complexing effect of the aqueous phase on zinc extraction. (Author) 36 p.

  20. Phytochemistry and hepatoprotective activity of aqueous extract of Amaranthus tricolor Linn. roots

    Directory of Open Access Journals (Sweden)

    Simran Aneja

    2013-01-01

    Full Text Available Background: The genus Amaranthus has potential activity as a hepatoprotective agent. Objective : The present pharmacological investigation focuses on evaluation of the efficacy of aqueous extract of roots of Amaranthus tricolor Linn. for their protection against paracetamol (PCM overdose induced hepatotoxicity . Materials and Methods: The aqueous extract of roots of A. tricolor Linn. was prepared and phytochemical screening was done. The biochemical investigation viz. serum glutamic oxaloacetate transaminase (SGOT, serum glutamic pyruvate transaminase (SGPT, alkaline phosphatase (ALP and total Bilirubin (TB was done against PCM-induced hepatotoxicity in wistar albino rats. The histopathological studies of liver were also done. Results: The phytochemical screening of the aqueous extract showed the presence of alkaloids, carbohydrates, flavanoids, amino acids, proteins, fixed oil, saponins and tannins, and phenolic compounds. Pretreatment with the aqueous extract of root significantly prevented the physical, biochemical, histological, and functional changes induced by paracetamol in the liver. The extract showed significant hepatoprotective effects as evidenced by decreased serum enzyme activities like SGPT, SGOT, ALP, and TB, which was supported by histopathological studies of liver. The aqueous extract showed significant hepatoprotective activity comparable with standard drug silymarin as well as hepatotoxin drug PCM. Conclusion: From these results, it is concluded that the A. tricolor has potential effectiveness in treating liver damage in a dose dependent manner.

  1. Saffron (Crocus sativus) aqueous extract and its constituent crocin reduces stress-induced anorexia in mice.

    Science.gov (United States)

    Halataei, Bahar-al-Sadat; Khosravi, Maryam; Arbabian, Sedigheh; Sahraei, Hedayat; Golmanesh, Leila; Zardooz, Homeira; Jalili, Cyrus; Ghoshooni, Hassan

    2011-12-01

    In the present study, the effects of an ethanol and aqueous extract of saffron Crocus sativus and its constituents safranal and crocin on the stress-induced reduction in food intake, weight gain and anorexic time in mice were investigated. Male albino mice (20-25 g) were irregularly exposed to a trial of electroshock stress for 7 days. Then, the anorexic time as well as the animal's food intake and weight were recorded. In addition, blood samples were obtained on days 1 and 7 for corticosterone determination. Intraperitoneal (i.p.) administration of the aqueous but not the ethanol extract (10, 50 and 100 mg/kg) significantly reduced the anorexic time. The results were similar for crocin (1, 5 and 10 mg/kg; i.p.). In addition, a reduction in weight gain was observed in the controls as well as in the groups that received alcohol extract or safranal. However, this was not observed in animals treated with aqueous extract or crocin. The plasma corticosterone level did not increase in the aqueous extract and crocin treated animals. It can be concluded that the saffron aqueous extract and its constituent crocin reduce side effects of electroshock stress in mice.

  2. Alleloppathic effects and insecticidal activity of the aqueous extract of Satureja montana L.

    Directory of Open Access Journals (Sweden)

    Šućur Jovana

    2015-01-01

    Full Text Available Extensive use of synthetic insecticides, herbicides and other pesticides has negative effects on the environment and on human and animal health. Therefore scientists are turning towards natural pesticides such as active components of plant extracts. Effect of two concentrations (0.1% and 0.2% of Satureja montana L. aqueous extract on lipid peroxidation process, as well as the activity of the antioxidant enzymes (SOD, GPX, PPX and CAT in leaves and roots of pepper and black nightshade seedlings were examined 24, 72 and 120h after the treatment. Our results showed that higher concentration of S. montana aqueous extract induced lipid peroxidation in black nightshade roots. Furthermore, significant increases of pyrogallol and guaiacol peroxidase were detected in black nightshade leaves treated with 0.2% S. montana aqueous extract. The second aim was to evaluate effectiveness of aqueous extract as contact toxicant against whitefly. It was observed that aqueous extract with concentration of 0.2% showed toxic effect with 68.33% mortality after 96h.

  3. Activity of the aqueous extract of Schinus terebinthifolius Raddi on strains of the Candida genus.

    Science.gov (United States)

    Torres, Kátia Andrea de Menezes; Lima, Sônia Maria Rolim Rosa; Ueda, Suely Mitoi Ykko

    2016-12-01

    Objectives To evaluate the antifungal susceptibility profile of the aqueous extract of the bark of Schinus terebinthifolius Raddi against the strains of the genus Candida. Methods By using the disk diffusion method, 50 samples of the genus Candida (Candida albicans; Candida krusei; Candida glabrata; and Candida tropicalis), isolated from patients receiving treatment at Hospital Santa Casa de Misericórdia de São Paulo, and 1 American Type Culture Collection (ATCC) sample of each species were tested against: the isolated aqueous extract of the bark of Schinus terebinthifolius Raddi, isolated nystatin, and the association of nystatin and the aqueous extract of Schinus terebinthifolius Raddi. Results There were no significant differences regarding the different strains of Candida tested. In the presence of the aqueous extract of Schinus terebinthifolius Raddi, no inhibition halo was visible. Isolated nystatin formed an inhibition halo measuring respectively 18.50 mm and 19.50 mm for the Candida albicans species and the others referred to as non-Candida albicans (Candida krusei; Candida glabrata; and Candida tropicalis). The association of nystatin and the aqueous extract of Schinus terebinthifolius Raddi resulted in inhibition halos measuring 14.25 mm and 16.50 mm respectively. The comparisons of these results are statistically significant (p < 0,001). Conclusion The aqueous extract of Schinus terebinthifolius Raddi showed no antifungal activity in vitro against the strains tested, whereas the association of nystatin and the aqueous extract of Schinus terebinthifolius Raddi caused a decrease in the inhibition halo when compared with isolated nystatin.

  4. Allelopathy of aqueous leaf extracts from the invasive alien tree Pittosporum undulatum on germination and growth of barnyard grass

    Directory of Open Access Journals (Sweden)

    Fernando Bertol Carpanezzi

    2014-09-01

    Full Text Available Barnyard grass (Echinochloa crusgalli (L. P. Beauv. is a herbicide-resistant weed that brings negative impacts to rice crops and threatens floodplains biodiversity worldwide. This study aimed to investigate allelopathic influences of extracts from Pittosporum undulatum Vent. (cheesewood leaves on barnyard grass. Leachates in concentrations of 20%, 15%, 10%, 5% and 2.5% (w/v, aqueous extracts from powdered leached and non-leached leaves (10%, 7,5%, 5%, 2.5% and 1.25% for both, coumarin solution at 0.6 mM and original Roundup ® in concentration according to the label information were prepared. Petri-dishes germination bioassays, with counting at each 12 hours, allowed to determinate both germinability and germination rate; polyethylene glycol (PEG 6000 solutions were prepared to evaluate osmotic effects. In growth tests, seedlings were exposed for seven days, when root and shoot lengths were measured. Germination was sensitive to extracts from powdered leaves. In regard to growth, roots showed dose-dependent length reduction and necrosis. Inhibitory effects from different aqueous extracts suggest action of both internal and external leaf allelochemicals, raising the possibility of Pittosporum undulatum use for barnyard grass control.

  5. Postprandial glycaemia and inhibition of α-glucosidase activity by aqueous extract from Coriandrum sativum.

    Science.gov (United States)

    Brindis, F; González-Andrade, M; González-Trujano, M E; Estrada-Soto, S; Villalobos-Molina, R

    2014-01-01

    The antihyperglycaemic properties of the aqueous extract from the leaves and stems of Coriandrum sativum L. were evaluated in normoglycaemic rats, and on α-glucosidase activity from Saccharomyces cerevisiae, in order to validate its use in folk medicine. In in vivo experiments rats were administered with the aqueous extract of the plant at 100, 300 and 500 mg/kg, to observe the effect on oral sucrose tolerance test. The aqueous extract exhibited significant antihyperglycaemic activity at the three tested doses. In vitro experiments with α-glucosidase exhibited a competitive-type inhibition. These results confirm the antidiabetic properties of the extract of C. sativum L., probably by the inhibition of α-glucosidase in the gastrointestinal tract.

  6. Aqueous solutions of acidic ionic liquids for enhanced stability of polyoxometalate-carbon supercapacitor electrodes

    Science.gov (United States)

    Hu, Chenchen; Zhao, Enbo; Nitta, Naoki; Magasinski, Alexandre; Berdichevsky, Gene; Yushin, Gleb

    2016-09-01

    Nanocomposites based on polyoxometalates (POMs) nanoconfined in microporous carbons have been synthesized and used as electrodes for supercapacitors. The addition of the pseudocapacitance from highly reversible redox reaction of POMs to the electric double-layer capacitance of carbon lead to an increase in specific capacitance of ∼90% at 1 mV s-1. However, high solubility of POM in traditional aqueous electrolytes leads to rapid capacity fading. Here we demonstrate that the use of aqueous solutions of protic ionic liquids (P-IL) as electrolyte instead of aqueous sulfuric acid solutions offers an opportunity to significantly improve POM cycling stability. Virtually no degradation in capacitance was observed in POM-based positive electrode after 10,000 cycles in an asymmetric capacitor with P-IL aqueous electrolyte. As such, POM-based carbon composites may now present a viable solution for enhancing energy density of electrical double layer capacitors (EDLC) based on pure carbon electrodes.

  7. Laser stimulated extraction of Pd from solution with uranyl

    Energy Technology Data Exchange (ETDEWEB)

    Vlasov, M.; Mironov, S. [Gosudarstvennyj Komitet po Ispol`zovaniyu Atomnoj Ehnergii SSSR, Moscow (Russian Federation). Inst. Atomnoj Ehnergii; Krynetsky, B.; Kukhtenko, A.; Prokhorov, A.; Zhidkov, A.

    1995-03-01

    Have been investigated process of the extraction of metal palladium from solution Pd{sup 2}+HClO{sub 4}+(UO{sub 2}{sup 2+}) by radiation excimer XeCl-laser ({lambda}=308 nm). By optimal parameters of solution efficiency of extraction was about 100%. Have been discussed processes reduction of palladium by resonance laser action. (author).

  8. Kinetics and thermodynamics of textile dye adsorption from aqueous solutions using babassu coconut mesocarp

    Energy Technology Data Exchange (ETDEWEB)

    Vieira, Adriana P.; Santana, Sirlane A.A.; Bezerra, Cicero W.B.; Silva, Hildo A.S. [Departamento de Quimica/CCET, Universidade Federal do Maranhao, Av. dos, Portugueses S/N, Campus do Bacanga, 65080-540 Sao Luis, Maranhao (Brazil); Chaves, Jose A.P. [Colegio Universitario, Universidade Federal do Maranhao, 65080-540 Sao Luis, Maranhao (Brazil); Melo, Julio C.P. de [Institute of Chemistry, University of Campinas, UNICAMP, P.O. Box 6154, 13084-971 Campinas, Sao Paulo (Brazil); Silva Filho, Edson C. da [Quimica, Universidade Federal do Piaui, 64900-000 Bom Jesus, Piaui (Brazil); Airoldi, Claudio, E-mail: airoldi@iqm.unicamp.br [Institute of Chemistry, University of Campinas, UNICAMP, P.O. Box 6154, 13084-971 Campinas, Sao Paulo (Brazil)

    2009-07-30

    Extracted babassu coconut (Orbignya speciosa) mesocarp (BCM) was applied as a biosorbent for aqueous Blue Remazol R160 (BR 160), Rubi S2G (R S2G), Red Remazol 5R (RR 5), Violet Remazol 5R (VR 5) and Indanthrene Olive Green (IOG) dye solutions. The natural sorbent was processed batchwise while varying several system parameters such as stirring time, pH and temperature. The interactions were assayed with respect to both pseudo-first-order and second-order reaction kinetics, with the latter the more suitable kinetic model. The maximum adsorption was obtained at pH 1.0 for all dyes due to available anionic groups attached to the structures, which can be justified by pH{sub pzc} 6.7 for the biosorbent BCM. The ability of babassu coconut mesocarp to adsorb dyes gave the order R S2G > VR 5 > BR 160 > IOG > RR 5, which data were best fit to Freundlich model, but did not well-adjusted for all dyes. The dye/biopolymer interactions at the solid/liquid interface are all spontaneous as given by free Gibbs energy, with exothermic enthalpic values of -26.1, -15.8, -17.8, -15.8 and -23.7 kJ mol{sup -1} for BR 160, R S2G, RR 5, IOG and VR 5, respectively. In spite of the negative entropic values contribution, the set of thermodynamic data is favorable for all dyes removal. However, the results pointed to the effectiveness of the mesocarp of babassu coconut as a biosorbent for removing textile dyes from aqueous solutions.

  9. Treatment of infectious skin defects or ulcers with electrolyzed strong acid aqueous solution.

    Science.gov (United States)

    Sekiya, S; Ohmori, K; Harii, K

    1997-01-01

    A chronic ulcer with an infection such as methicillin-resistant Staphylococcus aureus is hard to heal. Plastic and reconstructive surgeons often encounter such chronic ulcers that are resistant to surgical or various conservative treatments. We applied conservative treatment using an electrolyzed strong acid aqueous solution and obtained satisfactory results. The lesion was washed with the solution or soaked in a bowl of the solution for approximately 20 min twice a day. Fresh electrolyzed strong acid aqueous solution is unstable and should be stored in a cool, dark site in a sealed bottle. It should be used within a week after it has been produced. Here we report on 15 cases of infectious ulcers that were treated by electrolyzed strong acid aqueous solution. Of these cases, 7 patients were healed, 3 were granulated, and in 5, infection subsided. In most cases the lesion became less reddish and less edematous. Discharge or foul odor from the lesion was decreased. Electrolyzed strong acid aqueous solution was especially effective for treating a chronic refractory ulcer combined with diabetes melitus or peripheral circulatory insufficiency. This clinically applied therapy of electrolyzed strong acid aqueous solution was found to be effective so that this new therapeutic technique for ulcer treatment can now be conveniently utilized.

  10. Phytotoxic effects of aqueous leaf extracts of four Myrtaceae species on three weeds

    Directory of Open Access Journals (Sweden)

    Maristela Imatomi

    2015-05-01

    Full Text Available Research on allelopathic interactions can be useful in the search for phytotoxins produced by plants that may be employed as natural herbicides. The aim of this study was to assess the phytotoxic action of aqueous leaf extract of Blepharocalyx salicifolius, Myrcia multiflora, Myrcia splendens and Myrcia tomentosa on the germination and development of three weeds. The working hypothesis was that leaf extracts of Myrtaceae may negatively influence the development of weed species. Aqueous leaf extracts at 5 and 10% (g mL-1 were tested on the germination and growth of Euphorbia heterophylla, Echinochloa crus-galli and Ipomoea grandifolia and compared with the herbicide oxyfluorfen and distilled water (control. The most extracts caused pronounced delays in seed germination and inhibited the growth of seedlings of E. heterophylla; I. grandifolia and E. crus-galli, with the last target species had no growth shoot inhibited by the extracts. In this study, the potential and efficiency of the tested aqueous leaf extracts were evident because they were more phytotoxic to the weeds than the herbicide. Thus, the aqueous extracts of leaves from Myrtaceae species show potential for the isolation of active compounds that can be used for the production of natural herbicides in the future.

  11. Supercooling of aqueous dimethylsulfoxide solution at normal and high pressures: Evidence for the coexistence of phase-separated aqueous dimethylsulfoxide solutions of different water structures.

    Science.gov (United States)

    Kanno, H; Kajiwara, K; Miyata, K

    2010-05-21

    Supercooling behavior of aqueous dimethylsulfoxide (DMSO) solution was investigated as a function of DMSO concentration and at high pressures. A linear relationship was observed for T(H) (homogeneous ice nucleation temperature) and T(m) (melting temperature) for the supercooling of aqueous DMSO solution at normal pressure. Analysis of the DTA (differential thermal analysis) traces for homogeneous ice crystallization in the bottom region of the T(H) curve for a DMSO solution of R=20 (R: moles of water/moles of DMSO) at high pressures supported the contention that the second critical point (SCP) of liquid water should exist at P(c2)= approximately 200 MPa and at T(c2)temperature of SCP). The presence of two T(H) peaks for DMSO solutions (R=15, 12, and 10) suggests that phase separation occurs in aqueous DMSO solution (Rtemperatures (different liquid water structures [LDL-like and HDL-like structures (LDL: low-density liquid water, HDL: high-density liquid water)] in the pressure range of 120-230 MPa.

  12. Use of Cistus aqueous extracts as botanical fungicides in the control of Citrus sour rot.

    Science.gov (United States)

    Karim, H; Boubaker, H; Askarne, L; Cherifi, K; Lakhtar, H; Msanda, F; Boudyach, E H; Ait Ben Aoumar, A

    2017-03-01

    In this work, we investigated the in vitro and in vivo antifungal activity of aqueous extracts obtained from eight Cistus plant species against the development of Geotrichum citri-aurantii, the causal agent of citrus sour rot. The results demonstrate the in vitro effectiveness of all tested Cistus species aqueous extracts against G. citri-aurantii, the inhibition of mycelial growth ranged between 80 and 100%. Furthermore, Cistus aqueous extracts totally inhibited germination of G. citri-aurantii arthrospores at a concentration of 5 mg/mL. Among the plant species tested, C. laurifolius, C. salviifolius, C. monspeliensis, C. ladanifer and C. populifolius displayed the best fungistatic activity since the minimum inhibitory concentration (MIC) was rot was lowered to 8.33% when fruits were treated with aqueous extracts of C. populifolius and C. creticus compared to 100% in the control. Disease severity was lowered to 3.74, 4.47 and 5.13% when fruits were treated with C. creticus, C. ladanifer and C. populifolius aqueous extracts, respectively. Using such these biopesticides in a replacement for synthetic fungicides or in combination with other established disease management practices could help control citrus postharvest decay in a more sustainable and eco-friendly way.

  13. Vasorelaxant action of aqueous extract of the leaves of Persea americana on isolated thoracic rat aorta.

    Science.gov (United States)

    Owolabi, Mbang A; Jaja, Smith I; Coker, Herbert A B

    2005-09-01

    The present study investigated the vasorelaxant action of the aqueous leaves extract of Persea americana on isolated rat aorta. The results showed that the extract produced significant vasorelaxation and that the effect is dependent on the synthesis or release of endothelium-derived relaxing factors (EDRFs) as well as the release of prostanoid. The extract also reduced vasoconstriction probably by inhibiting Ca2+ influx through calcium channels.

  14. Aqueous enzyme assisted oil extraction from oilseeds and emulsion de-emulsifying methods: a review

    OpenAIRE

    Mat Yusoff, Masni; Gordon, Mike; Niranjan, Keshavan

    2014-01-01

    Regulatory, safety, and environmental issues have prompted the development of aqueousenzymatic extraction (AEE) for extracting components from oil-bearing materials. The emulsion resulting from AEE requires de-emulsification to separate the oil; when enzymes are used for this purpose, the method is known as aqueous enzymatic emulsion de-emulsification (AEED). In general, enzyme assisted oil extraction is known to yield oil having highly favourable characteristics. This review covers techno...

  15. Antimicrobial effects of aqueous plant extracts on the fungi Microsporum canis and Trichophyton rubrum and on three bacterial species.

    Science.gov (United States)

    Maoz, M; Neeman, I

    1998-01-01

    Aqueous extracts of 10 plants were tested for their ability to inhibit Trichophyton rubrum and Microsporum canis, the aetiological agents of dermal fungal infections in humans. These extracts were also evaluated for their activity against some bacteria. Aqueous extracts from the leaves of Inula viscosa produced detectable antifungal activity against these dermatophytes.

  16. Be2+ hydration in concentrated aqueous solutions of BeCl2.

    Science.gov (United States)

    Mason, Philip E; Ansell, Stuart; Neilson, George W; Brady, John W

    2008-02-21

    Neutron diffraction experiments were carried out on concentrated aqueous solutions of beryllium chloride at three concentrations: 1.5, 3, and 6 molal. By working with a specific ("null") mixture of heavy water (D2O) and water (H2O), information on the local structure around Be2+ ions was extracted directly. For all three BeCl2 solutions, the results show that the Be2+ ion has a well-defined 4-fold coordination shell that is dominated by oxygen atoms. There is also a relatively small probability (10-15%) that there are direct contacts between Be2+ and Cl- at a distance of approximately 2.2 angstroms. The oxygen atoms of the highly structured Be2+ first hydration shell are found to be situated at 2.6 angstroms apart, and form a pyramidal structure, in agreement with recent MD simulation results. The Cl- ions have approximately seven oxygen atoms (water molecules) in their hydration shells sited at 3.2 angstroms.

  17. Enthalpy of solution of CO{sub 2} in aqueous solutions of 2-amino-2-methyl-1-propanol

    Energy Technology Data Exchange (ETDEWEB)

    Arcis, Hugues [Laboratoire de Thermodynamique des Solutions et des Polymeres, Universite Blaise Pascal, Clermont-Ferrand/CNRS, 63177 Aubiere (France); Rodier, Laurence [Laboratoire de Thermodynamique des Solutions et des Polymeres, Universite Blaise Pascal, Clermont-Ferrand/CNRS, 63177 Aubiere (France); Coxam, Jean-Yves [Laboratoire de Thermodynamique des Solutions et des Polymeres, Universite Blaise Pascal, Clermont-Ferrand/CNRS, 63177 Aubiere (France)]. E-mail: j-yves.coxam@univ-bpclermont.fr

    2007-06-15

    The enthalpies of solution of CO{sub 2} in aqueous solution of 2-amino-2-methyl-1-propanol (AMP) 15 wt% and 30 wt% were measured at 322.5 K and pressures range from (0.2 to 5) MPa using a flow calorimetric technique. The gas solubilities were simultaneously determined from the calorimetric data. The solubilities were compared to available literature values obtained by direct measurements. The experimental enthalpies of solution were compared to the values derived from the literature vapor liquid equilibrium data. This work provides calorimetric data that will be used later for the development of a thermodynamic model to predict both solubilities and enthalpies of solution of acid gases in aqueous amine solutions.

  18. Tetraethyl Orthosilicate Coated Hydroxyapatite Powders for Lead Ions Removal from Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Rodica V. Ghita

    2014-01-01

    Full Text Available The goal of this study was to synthetize and characterize a porous material based on tetraethyl orthosilicate (TEOS coated hydroxyapatite (HApTh after removal experiments of Pb2+ ions from aqueous solutions. In order to study the morphology and composition, the samples obtained after removal experiments of Pb2+ ions from aqueous solution with the initial Pb2+ ion concentrations of the aqueous solutions were 0.1 g·L−1 (HApTh-50 and 0.9 g·L−1 (HApTh-450 have been investigated by scanning electron microscopy (SEM equipped with an energy dispersive X-ray spectrometer (EDS, Fourier transform infrared spectroscopy (FTIR, and transmission electron microscopy (TEM. Removal experiments of Pb2+ ions were carried out in aqueous solutions with controlled concentration of Pb2+. After the removal experiment of Pb2+ ions from solutions, porous hydroxyapatite nanoparticles were transformed into HApTh-50 and HApTh-450 due to the adsorption of Pb2+ ions followed by a cation exchange reaction. The obtained results show that the porous HApTh nanopowders could be used for Pb2+ ions removal from aqueous solutions.

  19. Anticonvulsant activity of aqueous extract of Leonotis leonurus.

    Science.gov (United States)

    Bienvenu, E; Amabeoku, G J; Eagles, P K; Scott, G; Springfield, E P

    2002-04-01

    Water extract of Leonotis leonurus was tested for anticonvulsant activity against seizures produced in mice by pentylenetetrazole, picrotoxin, bicuculline and N-methyl-DL-aspartic acid (intraperitoneal injections). L. leonurus extract in the doses of 200 and 400 mg/kg respectively protected 37.5% and 50% of animals used and significantly (p leonurus extract significantly (p leonurus used did not alter the seizures induced by bicuculline (20 mg/kg) to any significant extent. The data suggest that the extract of L. leonurus has anticonvulsant activity and may probably be acting through non-specific mechanisms, since it affects both gabaergic and glutaminergic systems. High performance liquid chromatography (HPLC) and phytochemical tests carried out respectively show a spectrum profile, characteristic of L. leonurus and the presence of alkaloids, saponins and tannins in the extract.

  20. Experimental determination of the temperature dependence of water activities for a selection of aqueous organic solutions

    Directory of Open Access Journals (Sweden)

    G. Ganbavale

    2014-05-01

    Full Text Available This work presents experimental data of the temperature dependence of water activity in aqueous organic solutions relevant for tropospheric conditions (200–273 K. Water activity (aw at low temperatures (T is a crucial parameter for predicting homogeneous ice nucleation. We investigated temperature dependent water activities, ice freezing and melting temperatures of solutions, and vapour pressures of a selection of atmospherically relevant aqueous organic systems. To measure aw over a wide composition range and with a focus on low temperatures, we use various aw measurement techniques and instruments: a dew point water activity meter, an electrodynamic balance (EDB, differential scanning calorimetry (DSC, and a setup to measure the total gas phase pressure at equilibrium over aqueous solutions. Water activity measurements were performed for aqueous multicomponent and multifunctional organic mixtures containing the functional groups typically found in atmospheric organic aerosols, such as hydroxyl, carboxyl, ketone, ether, ester, and aromatic groups. The aqueous organic systems studied at several fixed compositions over a considerable temperature range differ significantly in their temperature dependence. Aqueous organic systems of 1,4-butanediol and methoxyacetic acid show a moderate decrease in aw with decreasing temperature. The aqueous M5 system (a multicomponent system containing five different dicarboxylic acids and aqueous 2-(2-ethoxyethoxyethanol solutions both show a strong increase of water activity with decreasing temperature at high solute concentrations for TTaw can be reversed at low temperatures and that linear extrapolations of high temperature data may lead to erroneous predictions. To avoid this, experimentally determined aw at low temperature are needed to improve thermodynamic models towards lower temperatures and for improved predictions of the ice nucleation ability of organic–water systems.

  1. Solvent extraction of copper and zinc from bioleaching solutions with LIX984 and D2EHPA

    Institute of Scientific and Technical Information of China (English)

    LAN Zhuo-yue; HU Yue-hua; LIU Jian-she; WANG Jun

    2005-01-01

    The solvent extraction of copper and zinc from the bioleaching solutions of low-grade sulfide ores with LIX984 and D2EHPA was investigated. The influences of extractant content, aqueous pH value, phase ratio and equilibration time on metals extraction were studied. The results show that LIX984 has a higher selectivity for copper than for iron, zinc and other metals, and has the copper extraction rate above 97%,while the zinc and iron extraction rate is less than 1.6% respectively. Zinc extraction is carried out following the copper extraction from the raffinate. The zinc extraction with di(2-ethylhexyl) phosphoric acid(D2EHPA) is low due to its poor cation exchange. A sodium salt of D2EHPA is used and the zinc extraction rate is enhanced to above 98%. Though iron (Ⅲ) is strongly extracted before the extraction of zinc by D2EHPA, it is difficult to strip iron from the organic phase by sulfuric acid. The zinc stripping rate is above 99% with 100 g/L sulfuric acid, while that of iron is 0.16%. Hence, the separation of zinc from iron can be achieved by the selective stripping.

  2. Sorption Potentials of Waste Tyre for Some Heavy Metals (Pb Cd in Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Austin Kanayo ASIAGWU

    2009-07-01

    Full Text Available An investigation into the adsorption potential of activated and inactivated waste tyre powders for some heavy metals (Pb2+ and Cd2+ in their aqueous solution has been studied. The result indicated that inactivated waste tyre is a good non-conventional adsorbent for the removal of Cd from aqueous solution. A total of 93.3% of Cadmium contents was removed. The inactivated waste type proved a good adsorbent for the removal of Pb2+ 5g of 500mm activated tyre removed over 86.66% of Pb2+ from solution.

  3. Near-infrared studies of glucose and sucrose in aqueous solutions: water displacement effect and red shift in water absorption from water-solute interaction.

    Science.gov (United States)

    Jung, Youngeui; Hwang, Jungseek

    2013-02-01

    We used near infrared spectroscopy to obtain concentration dependent glucose absorption spectra in aqueous solutions in the near-infrared range (3800-7500 cm(-1)). Here we introduce a new method to obtain reliable glucose absorption bands from aqueous glucose solutions without measuring the water displacement coefficients of glucose separately. Additionally, we were able to extract the water displacement coefficients of glucose, and this may offer a new general method using spectroscopy techniques applicable to other water-soluble materials. We also observed red shifts in the absorption bands of water in the hydration shell around solute molecules, which comes from the contribution of the interacting water molecules around the glucose molecules in solutions. The intensity of the red shift gets larger as the concentration increases, which indicates that as the concentration increases more water molecules are involved in the interaction. However, the red shift in frequency does not seem to depend significantly on the concentration. We also performed the same measurements and analysis with sucrose instead of glucose as solute and compared.

  4. Modeling flavor release from aqueous sucrose solutions, using mass transfer and partition coefficients

    NARCIS (Netherlands)

    Nahon, D.F.; Harrison, M.; Roozen, J.P.

    2000-01-01

    The penetration theory of interfacial mass transfer was used to model flavor release from aqueous solutions containing different concentrations of sucrose. The mass transfer coefficient and the gas/solution partition coefficient are the main factors of the model influencing the release in time. Para

  5. Aqueous solutions of proline and NaCl studied by differential scanning calorimetry at subzero temperatures

    DEFF Research Database (Denmark)

    Rasmussen, Peter Have; Jørgensen, Bo; Nielsen, Jette

    1997-01-01

    The hydration properties of proline are studied by differential scanning calorimetry (DSC) in aqueous solutions during freezing to -60 degrees C and subsequent heating to +20 degrees C. The concentration of proline in the freeze concentrated solution was estimated to approximately 50 wt% (w/w) in...

  6. Direct evidence on the existence of [Mo132]Keplerate-type species in aqueous solution.

    Science.gov (United States)

    Roy, Soumyajit; Planken, Karel L; Kim, Robbert; Mandele, Dexx v d; Kegel, Willem K

    2007-10-15

    We demonstrate the existence of discrete single molecular [Mo(132)] Keplerate-type clusters in aqueous solution. Starting from a discrete spherical [Mo(132)] cluster, the formation of an open-basket-type [Mo(116)] defect structure is shown for the first time in solution using analytical ultracentrifugation sedimentation velocity experiments.

  7. Study on Thermosensitive Micellization of Dextran-g-PNIPAAm in Aqueous Solutions

    Institute of Scientific and Technical Information of China (English)

    Dan ZHAO; Li Qun WANG; Ke Hua TU; Song Wei TAN

    2006-01-01

    The thermosensitive micellization of dextran-g-PNIPAAm in aqueous solutions has been investigated by fluorescence spectroscopy, dynamic light scattering and transmission electron microscope. The formed polymeric micelles showed different diameters of about 20 nm or 100nm, when the solution temperature was below or above the phase transition temperature.

  8. KINETICS OF THE HYDROXYPROPYLATION OF POTATO STARCH IN AQUEOUS-SOLUTION

    NARCIS (Netherlands)

    LAMMERS, G; STAMHUIS, EJ; BEENACKERS, AACM

    1993-01-01

    Kinetic results are presented for the hydroxypropylation of Potato starch with methyloxirane in aqueous solution. Reaction temperatures were varied from 303 to 362 K. Sodium hydroxide was used as a catalyst. The overall conversion rate of methyloxirane in alkaline starch solution is determined by th

  9. Comparison of cytotoxicity in vitro and irritation in vivo for aqueous and oily solutions of surfactants.

    Science.gov (United States)

    Czajkowska-Kośnik, Anna; Wolska, Eliza; Chorążewicz, Juliusz; Sznitowska, Małgorzata

    2015-01-01

    The in vivo model on rabbit eyes and the in vitro cytotoxicity on fibroblasts were used to compare irritation effect of aqueous and oily (Miglyol 812) solutions of surfactants. Tween 20, Tween 80 and Cremophor EL were tested in different concentrations (0.1, 1 or 5%) and the in vitro test demonstrated that surfactants in oil are less cytotoxic than in aqueous solutions. In the in vivo study, the aqueous solutions of surfactants were characterized as non-irritant while small changes in conjunctiva were observed after application the oily solutions of surfactants and the preparations were classified as slightly irritant, however this effect was similar when Miglyol was applied alone. In conclusion, it is reported that the MTT assay does not correlate well with the Draize scores.

  10. Morphological modifications of selenium by recrystallization of its aqueous complex solutions.

    Science.gov (United States)

    Batabyal, Sudip K; Basu, C; Das, A R; Sanyal, G S

    2006-07-01

    Recrystallization of elemental selenium (Se) from aqueous solution in presence of sodium sulphite (Na2SO3) and sodium sulphide (Na2S) acting as complexing agents has resulted in the formation of nano and microstructures of Se having five different morphological modifications. (1) An aqueous solution of sodium selenosulphate (Na2SO3Se) obtained by dissolving Se in Na2SO3 under refluxing condition yields hemispherical microcrystals. (2) The filtrate of the above reaction mixture on aging produces hexagonal prismatic microrods of Se. Addition of Na2SO3Se solution to formalin (HCHO) at room temperature and refluxing conditions generates (3) Se nanorods, and (4) spherical microcrystals, respectively. (5) Recrystallization of Se from aqueous solution of Na2S develops flower shaped microcrystals.

  11. Phase-transition and aggregation characteristics of a thermoresponsive dextran derivative in aqueous solutions.

    Science.gov (United States)

    Shi, Huan-Ying; Zhang, Li-Ming

    2006-10-16

    Grafting of poly(N-vinylcaprolactam) side chains onto a hydrophilic dextran backbone was found to provide the dextran with new, thermoresponsive properties in aqueous solutions. Depending on its solution concentration, the resulting dextran derivative could exhibit a temperature-induced phase-transition and critical transition temperature (T(c)). Different anions and cations of added salts, including five potassium salts and five alkali-metal chlorides, were observed to influence the T(c) value of its aqueous solution. Except for potassium iodide, all added salts were found to lower the T(c) value. The addition of the surfactant, cationic cetyltrimethylammonium bromide or anionic sodium dodecyl sulfate, resulted in an increase of the T(c) value. With the help of the Coomassie Brilliant Blue dye as a polarity probe, the formation of hydrophobic aggregates above the T(c) was revealed for this new dextran derivative in aqueous solution.

  12. Ab initio aqueous thermochemistry: application to the oxidation of hydroxylamine in nitric acid solution.

    Science.gov (United States)

    Ashcraft, Robert W; Raman, Sumathy; Green, William H

    2007-10-18

    Ab initio molecular orbital calculations were performed and thermochemical parameters estimated for 46 species involved in the oxidation of hydroxylamine in aqueous nitric acid solution. Solution-phase properties were estimated using the several levels of theory in Gaussian03 and using COSMOtherm. The use of computational chemistry calculations for the estimation of physical properties and constants in solution is addressed. The connection between the pseudochemical potential of Ben-Naim and the traditional standard state-based thermochemistry is shown, and the connection of these ideas to computational chemistry results is established. This theoretical framework provides a basis for the practical use of the solution-phase computational chemistry estimates for real systems, without the implicit assumptions that often hide the nuances of solution-phase thermochemistry. The effect of nonidealities and a method to account for them is also discussed. A method is presented for estimating the solvation enthalpy and entropy for dilute aqueous solutions based on the solvation free energy from the ab initio calculations. The accuracy of the estimated thermochemical parameters was determined through comparison with (i) enthalpies of formation in the gas phase and in solution, (ii) Henry's law data for aqueous solutions, and (iii) various reaction equilibria in aqueous solution. Typical mean absolute deviations (MAD) for the solvation free energy in room-temperature water appear to be ~1.5 kcal/mol for most methods investigated. The MAD for computed enthalpies of formation in solution was 1.5-3 kcal/mol, depending on the methodology employed and the type of species (ion, radical, closed-shell) being computed. This work provides a relatively simple and unambiguous approach that can be used to estimate the thermochemical parameters needed to build detailed ab initio kinetic models of systems in aqueous solution. Technical challenges that limit the accuracy of the estimates are

  13. Cardioprotective Effect of the Aqueous Extract of Lavender Flower against Myocardial Ischemia/Reperfusion Injury

    Directory of Open Access Journals (Sweden)

    Dong Wang

    2014-01-01

    Full Text Available This study was conducted to evaluate the cardioprotective property of the aqueous extract of lavender flower (LFAE. The myocardial ischemia/reperfusion (I/R injury of rat was prepared by Langendorff retrograde perfusion technology. The heart was preperfused with K-H solution containing LFAE for 10 min before 20 minutes global ischemia, and then the reperfusion with K-H solution was conducted for 45 min. The left ventricular developed pressure (LVDP and the maximum up/downrate of left ventricular pressure (±dp/dtmax were recorded by physiological recorder as the myocardial function and the myocardial infarct size was detected by TTC staining. Lactate dehydrogenase (LDH and creatine kinase (CK activities in the effluent were measured to determine the myocardial injury degree. The superoxide anion dismutase (SOD and malondialdehyde (MDA in myocardial tissue were detected to determine the oxidative stress degree. The results showed that the pretreatment with LFAE significantly decreased the myocardial infarct size and also decreased the LDH, CK activities, and MDA level, while it increased the LVDP, ±dp/dtmax, SOD activities, and the coronary artery flow. Our findings indicated that LFAE could provide protection for heart against the I/R injury which may be related to the improvement of myocardial oxidative stress states.

  14. The radiolysis of iodine in aqueous solutions containing methane

    Science.gov (United States)

    Paquette, Jean; Ford, Beverly L.

    The γ-radiolysis of iodine, iodine, iodate and periodate solutions containing methane has been investigated. Iodoalkanes are produced in these solutions upon irradiation. In the case of unbuffered iodine, iodate and periodate solutions at an initial concentration of 1.0 × 10 -4 mol dm -3, nearly all of the initial iodine is transformed into iodoalkanes after the absorption of a 4 kGy radiation dose. The yield of iodoalkanes is lower for iodine solutions and for iodide solutions buffered at neutral pH. It is concluded that the main reactions leading to the formation of iodoalkanes are CH 3+I 2→CH 3I+I and CH 3+I→CH 3I. In the case of iodate and periodate, these reactions could be preceeded by reactions involving the methyl radical and oxyiodine species: CH 3+IO x→CH 2O+HIO x-1.

  15. Effect of aqueous and ethanolic extracts of Lippia citriodora on candida albicans

    Science.gov (United States)

    Ghasempour, Maryam; Omran, Saeid Mahdavi; Moghadamnia, Ali Akbar; Shafiee, Faranak

    2016-01-01

    Introduction Because of resistance and side effects to common antifungal drugs activity, the research on herbal substances with antifungal activity is frequent. Lemon verbena (Lippia citriodora) is a member of Verbenaceae family. The aim of this study was to determine the anti-candida activities of the ethanolic and aqueous extracts of the lemon verbena leaves and compare them with nystatin and fluconazole. Methods In this 2015 study, 15 clinical isolates and standard strain of candida albicans PTCC 5027 were used, and the inhibitory effects of the ethanolic and aqueous extracts, Nystatin and Fluconazole, were evaluated using disk and well diffusion methods. Also, the minimal inhibitory concentration (MIC) was determined. Five concentrations of aqueous and ethanolic extracts (156–2500 μg/ml), Nystatin (8–128 μg/ml) and Fluconazole (4–64 μg/ml) were used in disk and well diffusion methods, and nine concentrations of aqueous and ethanolic extracts (19–5000 μg/ml), Nystatin (0.5–128 μg/ml), and Fluconazole (0.25–64 μg/ml) were applied for MIC. Data were analyzed using Tukey’s post-hoc and one-way ANOVA tests. The significant level was considered p < 0.05 in the current study. Results In the well and disk diffusion techniques, limited growth inhibition halos were produced around some clinical isolates at different concentrations of ethanolic extract; however, no growth inhibitory halo was observed with any concentrations of the aqueous extract. The MIC values of ethanolic extract, aqueous extract, Nystatin and Fluconazole for clinical isolated and standard strain were 833 ± 78.5and 625μg/ml; 4156 ± 67.4 and 2500 μg/ml; 10.13 ± 1.91 and 4 μg/ml; and 1.97 ± 0.25 and 1 μg/ml, respectively. Conclusion The results showed that the ethanolic extract was stronger than the aqueous extract of this plant, which can be used as an alternative for drugs. It is recommended that the ethanolic extract of this plant be investigated in vivo for better

  16. Extraction of penicillin G by aqueous two-phase system of [Bmim]BF4/NaH2PO4

    Institute of Scientific and Technical Information of China (English)

    LIU Qingfen; HU Xuesheng; WANG Yuhong; YANG Ping; XIA Hansong; YU Jiang; LIU Huizhou

    2005-01-01

    A novel approach for the extraction of penicillin G by aqueous two-phase system comprised of hydrophilic ionic liquid [Bmim]BF4 (1-butyl-3- methylimidazolium tetrafluoroborate) and NaH2PO4 is reported. The effects of some important parameters involving the concentration of NaH2PO4, the concentration of penicillin G, the amount of [Bmim]BF4 on the formation of aqueous two-phase system and the extraction yield of penicillin were investigated. The primary result shows that the ATPS can take advantage of penicillin concentrated in upper phase at higher pH value for penicillin extraction from its aqueous solution without emulsification.

  17. Solvent extraction of vanadium from sulfuric acid solution

    Institute of Scientific and Technical Information of China (English)

    WANG Mingyu; ZHANG Guiqing; WANG Xuewen; ZHANG Jialiang

    2009-01-01

    The behaviour of vanadium(V) extracted from sulfuric acid solution was investigated using Cyanex 923 as an cxtractant. The effects of the concentration of Cyanex 923 and the pH of the solution were studied. The extraction of vanadium(V) increases with the increase of Cyanex 923 concentration and shaking time. Cyanex 923 can extract vanadium(V) fi'om sulfuric acid solution at low pH conditions, and the best pH conditions for exuaction of vanadium(V) are at pH 1.0-2.0. The species extracted into the organic phase is VO2HSO4 with one molecule of Cyanex 923. Equilibrium studies were used to assess the extraction efficiency of vanadium(V) recovery from the sulfuric acid solution.

  18. Probing Regenerative Potential of Moringa oleifera Aqueous Extracts Using In vitro Cellular Assays

    Science.gov (United States)

    Fernandes, Evangeline E.; Pulwale, Anubha V.; Patil, Gauri A.; Moghe, Alpana S.

    2016-01-01

    Background: Molecules stimulating regeneration and proliferation of cells are of significance in combating ailments caused due to tissue injury, inflammation, and degenerative disorders. Moringa oleifera is one of the most valued food plants having the profile of important nutrients and impressive range of medicinal uses. Objective: To evaluate the potential of M. oleifera aqueous leaf and flower extracts to promote the proliferation of cells and explore their effect on cancer cell lines for assessment of safety. Materials and Methods: Aqueous leaf and flower extracts of M. oleifera were investigated for effect on rat-derived primary fibroblast, mesenchymal stem cells (MSCs), and cancer cell lines using cell proliferation assay. They were also tested and compared for wound healing, angiogenesis, and hepatoprotective effect using in vitro assays. Results: Statistically significant increase in the proliferation of primary rat fibroblast, MSCs, and angiogenesis was observed after treatment with aqueous flower extract. The aqueous leaf extract determined a comparatively moderate increment in the proliferation of MSCs and angiogenesis. It however showed prominent cytotoxicity to cancer cell lines and a significant hepatoprotective effect. Conclusion: A very clear difference in response of the two extracts to different types of cells was detected in this study. The aqueous flower extract exhibited a higher potential to stimulate cell proliferation while not exerting the same effect on cancer cell lines. The leaf extract on the other hand, had a prominent antitumor and hepatoptotective effects. SUMMARY Moringa oleifera flower extract showed significant ability to promote proliferation of rat fibroblast and mesenchymal stem cells. The extract also had prominent angiogenic and hepatoprotective effects.The extract did not influence proliferation of cancer cell lines indicating its safety for human consumption and use in pharmaceuticals.The Moringa oleifera leaf extract

  19. Hepatoprotective effect of leaves of aqueous ethanol extract of Cestrum nocturnum against paracetamol-induced hepatotoxicity

    Directory of Open Access Journals (Sweden)

    M. Imran Qadir

    2014-06-01

    Full Text Available The hepatoprotective activities of Cestrum nocturnum (Queen of Night was evaluated against the paracetamol induced hepatotoxicity in the mice. Aqueous ethanol (30:70 extract of plant was obtained by maceration. Results showed that aqueous ethanol extract of C. nocturnum (250 mg/kg and 500 mg/kg produced significant (p<0.05 hepatoprotective activities against paracetamol induced liver injury in Swiss albino mice. Histopathalogical studied of liver further supported the hepatoprotective effects of C. notrunum. Phyto-chemical screening showed the presence of alkaloids, flavonoids, saponins, terpenes, phenolic compounds, carbohydrates and volatile oils. Most of the flavonoids have hepatoprotective activity. Therefore, the hepatoprotective activity of C. nocturnum may be due to the presence of flavonoids and phenolic components. It was concluded from the present study that aqueous ethanol extract of leaves of C. nocturnum has hepatoprotective activity against the paracetamol-induced hepatotoxicity in albino mice.

  20. Anticonvulsant effect of Persea americana Mill (Lauraceae) (Avocado) leaf aqueous extract in mice.

    Science.gov (United States)

    Ojewole, John A O; Amabeoku, George J

    2006-08-01

    Various morphological parts of Persea americana Mill (Lauraceae) (avocado) are widely used in African traditional medicines for the treatment, management and/or control of a variety of human ailments, including childhood convulsions and epilepsy. This study examined the anticonvulsant effect of the plant's leaf aqueous extract (PAE, 50-800 mg/kg i.p.) against pentylenetetrazole (PTZ)-, picrotoxin (PCT)- and bicuculline (BCL)-induced seizures in mice. Phenobarbitone and diazepam were used as reference anticonvulsant drugs for comparison. Like the reference anticonvulsant agents used, Persea americana leaf aqueous extract (PAE, 100-800 mg/kg i.p.) significantly (p Persea americana leaf aqueous extract possesses an anticonvulsant property, and thus lends pharmacological credence to the suggested ethnomedical uses of the plant in the management of childhood convulsions and epilepsy.

  1. Aqueous extracts of Lippia turbinata and Aloysia citriodora (Verbenaceae): assessment of antioxidant capacity and DNA damage.

    Science.gov (United States)

    Portmann, Erika; Nigro, Marcela M López; Reides, Claudia G; Llesuy, Susana; Ricco, Rafael A; Wagner, Marcelo L; Gurni, Alberto A; Carballo, Marta A

    2012-03-01

    The aim of the present work was to make a contribution to the knowledge of aqueous extracts of Lippia turbinata and Aloysia citriodora (Verbenaceae; infusion and decoction) in relation with the establishment of its antioxidant activity and lack of DNA damage, for its potential use in therapeutics. The cytogenotoxic profile was evaluated through genotoxic biomarkers such as mitotic index, cellular proliferation kinetics, sister chromatid exchanges, single-cell gel electrophoresis assay, and micronucleus test in human peripheral blood lymphocyte cultures. No statistical differences were found (P > .05) between control and exposed cultures, even between both aqueous extracts. The total antioxidant capacity was shown to be higher in the decoction than in the infusion and both aqueous extracts protected against protein carbonylation and lipid peroxidation, the decoction being more efficient than the infusion (P < .005). These results suggest the safe use of these medicinal plants as chemoecologic agents in therapeutics.

  2. In vitro antibacterial effect of aqueous and ethanolic Moringa leaf extracts

    Institute of Scientific and Technical Information of China (English)

    Giselle Cristina Silva; Renata Albuquerque Costa; Antonio Adauto Fonteles Filho

    2011-01-01

    Objective:To evaluate the antibacterial effect of aqueous and ethanolic moringa leaf extracts (Moringa oleifera) on the growth of gram-positive and negative bacteria. Methods:Paper disks were soaked with 100, 200, 300 and 400μL of extract at 20 g/180 mL and 10 g/190 mL. All extracts were tested against Escherichia coli (ATCC25922), Staphylococcus aureus (ATCC25923), Vibrio parahaemolyticus, Enterococcus faecalis (ATCC29212), Pseudomonas aeruginosa (ATCC27853), Salmonella enteritidis (IH) and Aeromonas caviae. The susceptibility tests were performed using the modified disk diffusion method. Results:The strains E. coli, P. aeruginosa and S. enteritidis (IH) were resistant to all treatments. In general, disks with 400μL extract were the most efficient against S. aureus, V. parahaemolyticus, E. faecalis and A. caviae. Conclusions: The study indicates a promising potential for aqueous and ethanolic Moringa leaf extracts as alternative treatment of infections caused by the tested strains.

  3. Pharmacological evaluation of anxiolytic property of aqueous root extract of Cymbopogon citratus in mice

    Directory of Open Access Journals (Sweden)

    David Arome

    2014-01-01

    Full Text Available Aim: This study was designed to evaluate the anxiolytic property of aqueous root extract of Cymbopogon citratus in mice. Materials and Methods: In this study, stress induced hyperthermia (SIH, elevated plus maze (EPM and open field experimental models were employed. Results: In SIH model, the extract caused a significant (P 0.05 effect. In open field model, 200 mg/kg and 600 mg/kg extract doses significantly (P < 0.05 increased locomotion of the mice more than the standard, while rearing and defecation were less in the extract groups. Conclusion: In different experimental models used significant anxiolytic effect was observed of the aqueous extract at different dose levels in comparison to reference standard and normal saline group. This clearly justified its folkloric application in the treatment of anxiety disorders.

  4. Separation of compounds with multiple -OH groups from dilute aqueous solutions via complexation with organoboronate. [1,2-propanediol

    Energy Technology Data Exchange (ETDEWEB)

    Chow, Tina Kuo Fung.

    1992-05-01

    The complexing extractant agent investigated in this work is 3-nitrophenylboronic acid (NPBA) in its anionic form (NPB). NPBA and Aliquat 336 (quaternary amine) is dissolved in 2-ethyl-l-hexanol, and the extractant is contacted with aq. NaOH. Solutes investigated were 1,2-propanediol, glycerol, fructose, sorbitol and lactic acid. Batch extraction experiments were performed at 25{degree}C. Partition coefficients, distribution ratios and loadings are reported for varying concentrations of solute and NPB. All solutes complexed with NPB{sup {minus}}, with all complexes containing only one NPB{sup {minus}} per complex. The 1:1 complexation constants for the solutes glycerol, fructose and sorbitol follow trends similar to complexation with B(OH){sub 4}{sup {minus}} (aq.), i.e. the complexation constants increase with increasing number of {minus}OH groups available for complexation. Assumption of 1:1 complex is not valid for 1, 2-propanediol, which showed overloading (more than one mole of solute complexed to one mole NPB{sup {minus}}) at higher concentrations. The {minus}OH group on the NPB{sup {minus}} which is left uncomplexed after one solute molecule had bound to the other two {minus}OH groups may be responsible for the overloading. Overloading is also observed in extraction of tactic acid, but through a different mechanism. It was found that TOMA{sup +} can extract lactic acid to an extent comparable to the uptake of lactic acid by NPB{sup {minus}}. The complexation is probably through formation of an acid-base ion pair. Losses of NPBA into the aqueous phase could lead to problems, poor economics in industrial separation processes. One way of overcoming this problem would be to incorporate the NPBA onto a solid support.

  5. Reaction paths and equilibrium end-points in solid-solution aqueous-solution systems

    Science.gov (United States)

    Glynn, P.D.; Reardon, E.J.; Plummer, L.N.; Busenberg, E.

    1990-01-01

    Equations are presented describing equilibrium in binary solid-solution aqueous-solution (SSAS) systems after a dissolution, precipitation, or recrystallization process, as a function of the composition and relative proportion of the initial phases. Equilibrium phase diagrams incorporating the concept of stoichiometric saturation are used to interpret possible reaction paths and to demonstrate relations between stoichiometric saturation, primary saturation, and thermodynamic equilibrium states. The concept of stoichiometric saturation is found useful in interpreting and putting limits on dissolution pathways, but there currently is no basis for possible application of this concept to the prediction and/ or understanding of precipitation processes. Previously published dissolution experiments for (Ba, Sr)SO4 and (Sr, Ca)C??O3orth. solids are interpreted using equilibrium phase diagrams. These studies show that stoichiometric saturation can control, or at least influence, initial congruent dissolution pathways. The results for (Sr, Ca)CO3orth. solids reveal that stoichiometric saturation can also control the initial stages of incongruent dissolution, despite the intrinsic instability of some of the initial solids. In contrast, recrystallisation experiments in the highly soluble KCl-KBr-H2O system demonstrate equilibrium. The excess free energy of mixing calculated for K(Cl, Br) solids is closely modeled by the relation GE = ??KBr??KClRT[a0 + a1(2??KBr-1)], where a0 is 1.40 ?? 0.02, a1, is -0.08 ?? 0.03 at 25??C, and ??KBr and ??KCl are the mole fractions of KBr and KCl in the solids. The phase diagram constructed using this fit reveals an alyotropic maximum located at ??KBr = 0.676 and at a total solubility product, ???? = [K+]([Cl-] + [Br-]) = 15.35. ?? 1990.

  6. Modeling supercritical fluid extraction process involving solute-solid interaction

    Energy Technology Data Exchange (ETDEWEB)

    Goto, M.; Roy, B. Kodama, A.; Hirose, T. [Kumamoto Univ., Kumamoto (Japan)

    1998-04-01

    Extraction or leaching of solute from natural solid material is a mass transfer process involving dissolution or release of solutes from a solid matrix. Interaction between the solute and solid matrix often influences the supercritical fluid extraction process. A model accounting for the solute-solid interaction as well as mass transfer is developed. The BET equation is used to incorporate the interaction and the solubility of solutes into the local equilibrium in the model. Experimental data for the supercritical extraction of essential oil and cuticular wax from peppermint leaves are successfully analyzed by the model. The effects of parameters on the extraction behavior are demonstrated to illustrate the concept of the model. 18 refs., 5 figs., 1 tab.

  7. Optimization of Variables for Aqueous Extraction of Gum from Grewia mollis Powder

    Directory of Open Access Journals (Sweden)

    Emmanuel Panyoo Akdowa

    2014-01-01

    Full Text Available Grewia gum is a polysaccharide derived from the inner stem bark of the edible plant Grewia mollis. Juss (family Tiliaceae. It is a savanna shrub that grows wildly but is usually cultivated in Nigeria and Northern part of Cameroon. The main goal of the present study was to investigate the effect of aqueous extraction conditions on the extraction yield and physicochemical properties of the Grewia mollis. The studied aqueous extraction variables were water/powder (W/P ratio (10 : 1–80 : 1 w/p, temperature (25.0–85.0∘C, time (1–3 h, and pH (4.0–10.0. The results indicated that the aqueous extraction variables exhibited the least significant (P<0.05 effect on the yield and the viscosity of the gum. The result shows that the ratio of extraction is the main factor affecting the extraction of gum. The optimized extraction condition for higher viscosity was at the powder/water ratio of 1 : 55.4, pH of 7, time of 1 h, and temperature of 50∘C. However, the optimized extraction condition for higher yield was at the powder/water ratio of 1 : 80, pH of 4, time of 3 h, and temperature of 73∘C.

  8. Inhibition Effect of Mace Extract Microemulsion on Vitamin C Photooxidation in Aqueous Systems

    Directory of Open Access Journals (Sweden)

    Hasbullah Hasbullah

    2014-01-01

    Full Text Available Photooxidation in food systems cause nutritional losses and produces undesirable flavor, toxic and color compounds, which make foods less acceptable or unacceptable to consumers. The objective of this research was to know the effectiveness of mace extract microemulsion to inhibit vitamin C photooxidation in aqueous systems. Aqueous food systems used are both beverage model system and apple juice beverage, where in each system enriched by 100 ppm vitamin C as substrate and 20 ppm erytrosin as photosensitiser. It is about one percent and two percent of microemulsion that contain mace extract of 0, 500 and 750 ppm were added into each of aqueous food system. Inhibition effect of mace extract microemulsion toward vitamin C photooxidation based on the rate of vitamin C degradation in aqueous food systems that illuminated by fluorescent light with 2000 lux intensity within eight hours. The result indicated the mace extract microemulsion has anti-photooxidation activity and ability to inhibit vitamin C photooxidation in aqueous systems.

  9. Synthesis of tyrocidine A and its analogues by spontaneous cyclization in aqueous solution.

    Science.gov (United States)

    Bu, Xianzhang; Wu, Xiaoming; Xie, Guiyang; Guo, Zhihong

    2002-08-22

    [reaction: see text] Head-to-tail cyclization of peptides is a multistep process involving tedious C-terminal activation and side chain protection. Here we report a facile, quantitative cyclization method in aqueous ammonia solution for the total syntheses of the cyclic decapeptide antibiotic Tyrocidine A and its analogues from their fully deprotected linear thioester precursors on a solid support. This novel aqueous method is conformation-dependent and may be applicable to syntheses of other natural cyclic peptides.

  10. Solubility of Carbon Dioxide and Hydrogen Sulfide in Aqueous N-Methyldiethanolamine Solutions

    OpenAIRE

    Huttenhuis, P. J. G.; Agrawal, N.J.; Versteeg, G. F.

    2009-01-01

    In this work, 72 new experimental solubility data points for H(2)S and CO(2) mixtures in aqueous N-methyldiethanol amine (MDEA) solutions at different methane partial pressures (up to 69 bara) are presented. They are correlated using an electrolyte equation of state (E-EOS) thermodynamic model. This model has already been used to estimate the CO(2) solubility in aqueous MDEA (Huttenhuis et al. Fluid Phase Equilib. 2008, 264, 99-112) and the H(2)S solubility in aqueous MDEA (Huttenhuis et al. ...

  11. First-principle based modeling of urea decomposition kinetics in aqueous solutions

    Science.gov (United States)

    Nicolle, André; Cagnina, Stefania; de Bruin, Theodorus

    2016-11-01

    This study aims at validating a multi-scale modeling methodology based on an implicit solvent model for urea thermal decomposition pathways in aqueous solutions. The influence of the number of cooperative water molecules on kinetics was highlighted. The obtained kinetic model is able to accurately reproduce urea decomposition in aqueous phase under a variety of experimental conditions from different research groups. The model also highlights the competition between HNCO desorption to gas phase and hydrolysis in aqueous phase, which may influence SCR depollution process operation.

  12. The Content in Bioactive Compounds of Different Brewers' Spent Grain Aqueous Extracts

    Directory of Open Access Journals (Sweden)

    Anca FARCAS

    2016-11-01

    Full Text Available In the last decade by-products of food and beverage processing have attracted much attention due to their functionality and potential as food ingredients. Brewers’ spent grain is the major by-product of the brewing industry representing a valuable source of bioactive ingredients. The aim of this study was to assess the effect of extraction time and temperature on the efficiency of water as solvent for the extraction of bioactive compounds from brewers’ spent grain (BSG. In terms of extraction efficiency, the results from polyphenols, flavonoids and antioxidant activity, showed that the best extraction parameters for aqueous extracts are 90⁰C and 60 minutes. In comparison with the control, the best extraction method generated 87% of the phenolics and 43.46% of the flavonoids obtained by a methanol extraction. The preliminary results for the aqueous extracts showed that water can be used as extraction solvent, but a higher extraction time and temperature are needed in order to have a content in bioactive compounds similar to that of methanolic extracts. The obtained values for polyphenols, flavonoids and antioxidant activity, emphasize the importance and the opportunities of the reuse of this agro-industrial waste.

  13. Radiation induced degradation of ketoprofen in dilute aqueous solution

    Science.gov (United States)

    Illés, Erzsébet; Takács, Erzsébet; Dombi, András; Gajda-Schrantz, Krisztina; Gonter, Katalin; Wojnárovits, László

    2012-09-01

    The intermediates and final products of ketoprofen degradation were investigated in 0.4 mmol dm-3 solution by pulse radiolysis and gamma radiolysis. For observation of final products UV-vis spectrophotometry and HPLC separation with diode array detection were used, and for identification MS was used. The reactions of •OH lead to hydroxycyclohexadienyl type radical intermediates, in their further reactions hydroxylated derivatives of ketoprofen form as final products. The hydrated electron is scavenged by the carbonyl oxygen and the electron adduct protonates to ketyl radical •OH is more effective in decomposing ketoprofen than hydrated electron. Chemical oxygen demand and total organic carbon content measurements on irradiated aerated solutions showed that using irradiation technology ketoprofen can be mineralised. The initial toxicity of the solution monitored by the Daphnia magna test steadily decreases with irradiation. Using 5 kGy dose no toxicity of the solution was detected with this test.

  14. Forces between Hydrophobic Solids in Concentrated Aqueous Salt Solution

    OpenAIRE

    Mastropietro, Dean J; Ducker, William A.

    2012-01-01

    Much research has focused on the discovery and description of long-ranged forces between hydrophobic solids immersed in water. Here we show that the force between high contact-angle solids in concentrated salt solution (1 M KCl) agrees very well with van der Waals forces calculated from Lifshitz theory for separations greater than 5 nm. The hydrophobic solids are octadecyltrichlorosilane-coated glass, with an advancing contact angle of 108 degrees. Thus, in 1 M salt solution, it is unnecessar...

  15. Optimization and adsorption kinetic studies of aqueous manganese ion removal using chitin extracted from shells of edible Philippine crabs

    Science.gov (United States)

    Quimque, Mark Tristan J.; Jimenez, Marvin C.; Acas, Meg Ina S.; Indoc, Danrelle Keth L.; Gomez, Enjelyn C.; Tabuñag, Jenny Syl D.

    2017-01-01

    Manganese is a common contaminant in drinking water along with other metal pollutants. This paper investigates the use of chitin, extracted from crab shells obtained as restaurant throwaway, as an adsorbent in removing manganese ions from aqueous medium. In particular, this aims to optimize the adsorption parameters and look into the kinetics of the process. The adsorption experiments done in this study employed the batch equilibration method. In the optimization, the following parameters were considered: pH and concentration of Mn (II) sorbate solution, particle size and dosage of adsorbent chitin, and adsorbent-adsorbate contact time. At the optimal condition, the order of the adsorption reaction was estimated using kinetic models which describes the process best. It was found out that the adsorption of aqueous Mn (II) ions onto chitin obeys the pseudo-second order model. This model assumes that the adsorption occurred via chemisorption

  16. Volatile release from aqueous solutions under dynamic headspace dilution conditions.

    Science.gov (United States)

    Marin, M; Baek, I; Taylor, A J

    1999-11-01

    Static equilibrium was established between the gas phase (headspace) and an unstirred aqueous phase in a sealed vessel. The headspace was then diluted with air to mimic the situation when a container of food is opened and the volatiles are diluted by the surrounding air. Because this first volatile signal can influence overall flavor perception, the parameters controlling volatile release under these conditions are of interest. A mechanistic model was developed and validated experimentally. Release of compounds depended on the air-water partition coefficient (K(aw)) and the mass transport in both phases. For compounds with K(aw) values 10(-)(3), mass transport in the gas phase became significant and the Reynolds number played a role. Because release from packaged foods occurs at low Reynolds numbers, whereas most experiments are conducted at medium to high Reynolds numbers, the experimentally defined profile may not reflect the real situation.

  17. Direct Synthesis of Nanoceria in Aqueous Polyhydroxyl Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Karakoti, A. S.; Kuchibhatla, Satyanarayana V N T; Babu, K. S.; Seal, Sudipta

    2007-11-22

    Nanoceria has been shown to possess biomedical properties which have potential use in treatment of diseases caused by reactive oxygen species (ROS) like cancer. In the present work, stability and redox changes in nanoceria in the presence of polyhydroxyl groups such as glucose and dextran is reported. The effect of both acidic and basic medium on stability of nanoceria in the absence of buffer had been examined using UV-Visible spectroscopy and transmission electron microscopy. Experimental results showed that both dextran and glucose can extend the stability of nanoceria in basic medium without interfering with the redox chemistry. A comparison of aqueous and saccharides suspension in acid/base media undergoing redox transformation has been reported.

  18. Chemical and photochemical properties of chloroharmine derivatives in aqueous solutions.

    Science.gov (United States)

    Rasse-Suriani, Federico A O; Denofrio, M Paula; Yañuk, Juan G; Gonzalez, M Micaela; Wolcan, Ezequiel; Seifermann, Marco; Erra-Balsells, Rosa; Cabrerizo, Franco M

    2016-01-14

    Thermal and photochemical stability (Φ(R)), room temperature UV-vis absorption and fluorescence spectra, fluorescence quantum yields (Φ(F)) and lifetimes (τ(F)), quantum yields of hydrogen peroxide (Φ(H2O2)) and singlet oxygen (Φ(Δ)) production, and triplet lifetimes (τ(T)) have been obtained for the neutral and protonated forms of 6-chloroharmine, 8-chloroharmine and 6,8-dichloroharmine, in aqueous media. When it was possible, the effect of pH and oxygen concentration was evaluated. The nature of electronic transitions of protonated and neutral species of the three investigated chloroharmines was established using Time-Dependent Density Functional Theory (TD-DFT) calculations. The impact of all the foregoing observations on the biological role of the studied compounds is discussed.

  19. Allelopathic effects of the aqueous extract of the leaf and seed of Leucaena leucocephala on three selected weed species

    Science.gov (United States)

    Ishak, Muhamad Safwan; Sahid, Ismail

    2014-09-01

    A laboratory experiment was conducted to study the allelopathic effects of the aqueous extract of the leaf and seed of Leucaena leucocephala. The aqueous extracts were individually tested on three selected weed species, namely goatweed (Ageratum conyzoides), coat buttons (Tridax procumbens) and lilac tasselflower (Emilia sonchifolia). The allelopathic effects of the leaf and seed extracts on germination, shoot length, root length and fresh weight of each of the selected weed species were determined. Germination of goatweed, coat buttons and lilac tasselflower were inhibited by the aqueous extracts of both the leaf and seed of L. leucocephala and was concentration dependent. Different concentrations of the aqueous extracts showed various germination patterns on the selected weeds species. Seedling length and fresh weight of goatweed, coat buttons and lilac tasselflower were reduced in response to respective increasing concentrations of the seed extracts. Maximum inhibition by the aqueous seed extract was observed more on the root rather than the shoot growth. The aqueous seed extract at T3 concentration reduced root length of goatweed, coat buttons and lilac tasselflower by 95%, 86% and 91% (of the control) respectively. The aqueous seed extract showed greater inhibitory effects than that of the aqueous leaf extract.

  20. Electrochemical characteristics of dodecylbenzene sulfonic acid-doped polyaniline in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Choi, B.Y. [Korea Electr. Power Res. Inst., Taejon (Korea, Republic of). Power Utilization Group; Chung, I.J. [Department of Chemical Engineering, Korea Advanced Institute of Science and Technology, 373-1 Kusong Yusong, Taejon 305-701 (Korea, Republic of); Chun, J.H.; Ko, J.M. [Department of Industrial Chemistry, Taejon National University of Technology, 305-3, Samsung-2 dong, Dong-gu, Taejon 300-717 (Korea, Republic of)

    1999-02-26

    The electrochemical characteristics of the polyaniline (PAn) films doped with dodecylbenzene sulfonic acid (DBSA) were investigated in aqueous solutions by means of cyclic voltammetry. The PAn-DBSAs film showed a good electrochemical activity in a weak acid solution as well as in a strong acid solution due to the incorporation of small cation instead of DBSA trapped in the film for charge neutralization of polymer matrix. (orig.) 39 refs.