WorldWideScience

Sample records for aqueous alkaline solution

  1. Transient species produced in irradiated alkaline aqueous solutions containing oxygen

    International Nuclear Information System (INIS)

    The spectra and decay kinetics of the optical absorption in the UV region and at 430nm (maximum of the ozonide ion absorption), were investigated in oxygenated neutral, slightly and strongly alkaline aqueous solutions. It is assumed that the initial absorption after the pulse in oxygenated alkaline solutions is due to the ozonide ion O3-, superoxide radical ion O2- and ozone O3. The long-living absorption in these solutions cannot be excluded as to be probably caused by the ozone O3 or some product formed from O2- or an alkaline stabilized form of this radical-ion. The advantage of applying additional non-optical measurements of the system is shown on the example of H2O2 role played in the mechanism. (author)

  2. Decomposition Studies of Triphenylboron, Diphenylborinic Acid and Phenylboric Acid in Aqueous Alkaline Solutions Containing Copper

    Energy Technology Data Exchange (ETDEWEB)

    Crawford, C.L. [Westinghouse Savannah River Company, AIKEN, SC (United States); Peterson, R. A.

    1997-02-11

    This report documents the copper-catalyzed chemical kinetics of triphenylboron, diphenylborinic acid and phenylboric acid (3PB, 2PB and PBA) in aqueous alkaline solution contained in carbon-steel vessels between 40 and 70 degrees C.

  3. Dual fluorescence of naphthylamines in alkaline aqueous solution

    Science.gov (United States)

    Ma, Li-Hua; Wen, Zhen-Chang; Lin, Li-Rong; Jiang, Yun-Bao

    2001-10-01

    Dual fluorescence was observed with N-(1-naphthyl)aminoacetate (1-NAA) in aqueous solution of pH 13.0 in the presence of cationic surfactants, cetyltrimethylammonium bromide (CTAB) and chloride (CTAC), below and after the critical micelle concentration (CMC). Similar dual fluorescence was also found with 1- and 2-naphthylamine (1-NA, 2-NA), N-(2-naphthyl)aminoacetate (2-NAA) and (1-naphthyl)ethylenediamine (1-NEDA), in the presence and absence of the cationic surfactants, but not with N, N-disubstituted 1- and 2-NAs. We concluded that the dual fluorescence was due to the excited-state deprotonation of the amino group in these NAs. The p Ka*s of the dual fluorescent NAs were estimated to be around 14 from the dual fluorescence pH titrations. No clear correlation was found for p Ka* with the amino substitution and the presence of cationic micelle.

  4. Oxidative dissolution of spent nuclear fuel in aqueous alkaline solutions - An alternative to the Purex process?

    Energy Technology Data Exchange (ETDEWEB)

    Runde, Wolfgang; Peper, Shane; Brodnax, Lia; Crooks, William; Zehnder, Ralph; Jarvinen, Gordon

    2004-07-01

    As an alternative to acidic reprocessing of spent nuclear, oxidative dissolution of UO{sub 2} into aqueous alkaline solutions and subsequent separation of fission products is considered. The efficacy of such a method is limited by the kinetics of the UO{sub 2} dissolution and the capacity of alkaline solutions for dissolved U(VI) species. We performed a series of dissolution studies on UO{sub 2} and U{sub 3}O{sub 8} in aqueous alkaline solutions applying various oxidants. Among the oxidative agents commonly used to transform low-valence actinides into their higher oxidation states, H{sub 2}O{sub 2} has proven to be the most effective in basic media. Consequently, we investigated the dissolution of UO{sub 2} and U{sub 3}O{sub 8} in NaOH-H{sub 2}O{sub 2} and Na{sub 2}CO{sub 3}-H{sub 2}O{sub 2} solutions and determined the dissolution kinetics as a function of peroxide and hydroxide (carbonate) concentrations. Methods to remove fission products, e.g., Cs, Sr, Ba and Zr, from alkaline solutions will be evaluated based upon their decontamination factors. We will discuss the feasibility of using chemically oxidizing alkaline solutions as an alternative spent nuclear fuel reprocessing method based on results from experimental quantitative investigations. (authors)

  5. Enhanced oxygen evolution at hydrous oxy-hydroxide modified iron electrodes in aqueous alkaline solution

    OpenAIRE

    Lyons, Michael; Doyle, Richard

    2011-01-01

    Outstanding issues regarding the film formation and the oxygen evolution reaction (OER) electrocatalytic behaviour of multicycled iron oxyhydroxide films in aqueous alkaline solution have been revisited. The oxide is grown using a repetitive poltential multicycling technique, and the mechanism of the latter hydrous oxide formation process has been discussed. A duplex layer model of the oxide/solution interphase region is proposed. The acid/base behaviour of the hydrous oxide and the microdisp...

  6. Alkaline deoxygenated graphene oxide as adsorbent for cadmium ions removal from aqueous solutions.

    Science.gov (United States)

    Liu, Jun; Du, Hongyan; Yuan, Shaowei; He, Wanxia; Yan, Pengju; Liu, Zhanhong

    2015-01-01

    Alkaline deoxygenated graphene oxide (aGO) was prepared through alkaline hydrothermal treatment and used as adsorbent to remove Cd(II) ions from aqueous solutions for the first time. The characterization results of transmission electron microscopy, X-ray diffraction, Raman spectroscopy, and Fourier transform infrared (FT-IR) spectra indicate that aGO was successfully synthesized. The batch adsorption experiments showed that the adsorption kinetics could be described by the pseudo-second-order kinetic model, and the isotherms equilibrium data were well fitted with the Langmuir model. The maximum adsorption capacity of Cd(II) on aGO was 156 mg/g at pH 5 and T=293 K. The adsorption thermodynamic parameters indicated that the adsorption process was a spontaneous and endothermic reaction. The mainly adsorption mechanism speculated from FT-IR results may be attributed to the electrostatic attraction between Cd2+ and negatively charged groups (-CO-) of aGO and cation-π interaction between Cd2+ and the graphene planes. The findings of this study demonstrate the potential utility of the nanomaterial aGO as an effective adsorbent for Cd(II) removal from aqueous solutions. PMID:26038925

  7. Reaction of the hydroxyl radical with glutathione in neutrai and alkaline aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Sjoberg, L. (Royal Inst. of Tech., Stockholm, Sweden); Eriksen, T.E.; Revesz, L.

    1982-02-01

    The reaction of OH with glutathione (..gamma..-glu-cys-gly) in neutral and alkaline aqueous solutions has been studied by pulse radiolysis. In addition to the sulfur-centered GS-(GSSG/sup -/.) radical formed by electron transfer or hydrogen abstraction from GS/sup -/ (GSH), at least one carbon-centered radical is formed with pH-dependent yield by hydrogen abstraction from the ..gamma..-glutamyl moiety. The latter radical is transformed in a first-ordered reaction most probably to a carbon-centered radical on the cysteine group. No evidence for the formation of carbon-centered radicals was found in comparable experiments with cysteine and 2-mercaptopropionylglycine.

  8. A Convenient and Environmentally Benign Method of Reducing Aryl Ketones or Aldehydes by Zinc Powder in an Aqueous Alkaline Solution

    Institute of Scientific and Technical Information of China (English)

    ZHANG,Chao-Zhi; YANG,Hui; WU,De-Lin; LU,Guo-Yuan

    2007-01-01

    A convenient and environmentally benign method for reducing the carbonyl group in hydroxy- and amino-9,10-anthracenediones, ortho (or para) acyl phenols and acyl anilines to a methylene group by zinc powder in an aqueous sodium hydroxide solution was reported. Based on theoretical calculations using the density functional theory (DFT), the mechanism of these reduction reactions was postulated. This mechanism can be applied to help predicting the reduced products of aryl ketones (or aldehydes) in an alkaline solution.

  9. The oxygen evolution reaction on passive oxide covered transition metal electrodes in aqueous alkaline solution. Part 1 - Nickel

    OpenAIRE

    LYONS, MICHAEL EDWARD

    2008-01-01

    Various aspects of the oxygen evolution reaction (OER) at passive oxide covered polycrystalline Ni electrodes in aqueous alkaline solution were investigated using electrochemical techniques. Steady state polarisation and electrochemical impedance spectroscopy (EIS) were used to measure kinetically significant parameters including the Tafel slope and the reaction order with respect to OH- activity. While reproducible values of the Tafel slope were readily observed, the recorded cur...

  10. The reactivity of the electron formed in the radiolysis of aerated alkaline aqueous solutions containing tetracycline hydrochloride, at 77 Ksup(+)

    International Nuclear Information System (INIS)

    The radiolysis of tetracycline hydrochloride dissolved in aerated alkaline aqueous solutions containing 0.1, 0.5 and 1M NaOH at 77 K, followed by ESR is reported. The rate constants for the reactions between the electron and physical or chemical traps which are present in these solutions are calculated. The reactivity of electrons that are formed in the radiolysis of water decreases in the following proportions: physical traps: chemical traps: molecules of water (4.8x10sup(14) : 6.5x10sup(8) : 1.0). The electrons react preferentially with the solute instead of the solvent. (author)

  11. On the decay of the ozonide radical in aqueous alkaline solutions

    Science.gov (United States)

    Bhattacharyya, P. K.; Saini, R. D.

    1982-11-01

    In flash photolysis of an oxygenated aqueous potassium persulphate solution at pH 12.5 the decay of the ozonide radical has been found to follow 3/2 order kinetics which has been explained by reactions O -3 + O - ⇌ 2 O -2 and O -3 + HO 2 → 2 O 2 + OH -

  12. Investigation into formation of nanoparticles of tetravalent neptunium in slightly alkaline aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Husar, Richard

    2015-08-20

    Considering the worldwide growing discharge of minor actinides and the current need for geological disposal facilities for radioactive waste, this work provides a contribution to the safety case concerning Np transport if it would be released from deep repository sites and moving from alkaline cement conditions (near-field) to more neutral environmental conditions (far-field). The reducing conditions in a nuclear waste repository render neptunium tetravalent, which is assumed to be immobile in aqueous environment due to the low solubility solution of Np(IV). For tetravalent actinide nuclides, the most significant transport should occur via colloidal particles. This work demonstrates the formation of intrinsic neptunium dioxide nanocrystals and amorphous Np(IV) silica colloids under environmentally relevant conditions. The dissociation of the initial soluble Np(IV) complex (i.e. [Np(IV)(CO{sub 3}){sub 5}]{sup 6-}) induces the intrinsic formation of nanocrystalline NpO{sub 2} in the solution phase. The resulting irregularly shaped nanocrystals with an average size of 4 nm exhibit a face-centered cubic (fcc), fluorite-type structure (space group Fm anti 3m). The NCs tend to agglomerate under ambient conditions due to the weakly charged hydrodynamic surface at neutral pH (zetapotential ζ ∝0 mV). The formation of micron-sized agglomerates, composed of nanocrystals of 2-5 nm in size, and the subsequent precipitation cause immobilization of the major amount of Np(IV) in the Np carbonate system. Agglomeration of NpO{sub 2} nanocrystals in dependence on time was indicated by PCS and UV-vis absorption spectroscopy with the changes of baseline characteristics and absorption maximum at 742 nm. Hitherto, unknown polynuclear species as intermediate species of NpO{sub 2} nanocrystal formation were isolated from solution and observed by HR-TEM. These polynuclear Np species appear as dimers, trimers and hexanuclear compounds in analogy with those reported for other actinides

  13. Investigation into formation of nanoparticles of tetravalent neptunium in slightly alkaline aqueous solution

    International Nuclear Information System (INIS)

    Considering the worldwide growing discharge of minor actinides and the current need for geological disposal facilities for radioactive waste, this work provides a contribution to the safety case concerning Np transport if it would be released from deep repository sites and moving from alkaline cement conditions (near-field) to more neutral environmental conditions (far-field). The reducing conditions in a nuclear waste repository render neptunium tetravalent, which is assumed to be immobile in aqueous environment due to the low solubility solution of Np(IV). For tetravalent actinide nuclides, the most significant transport should occur via colloidal particles. This work demonstrates the formation of intrinsic neptunium dioxide nanocrystals and amorphous Np(IV) silica colloids under environmentally relevant conditions. The dissociation of the initial soluble Np(IV) complex (i.e. [Np(IV)(CO3)5]6-) induces the intrinsic formation of nanocrystalline NpO2 in the solution phase. The resulting irregularly shaped nanocrystals with an average size of 4 nm exhibit a face-centered cubic (fcc), fluorite-type structure (space group Fm anti 3m). The NCs tend to agglomerate under ambient conditions due to the weakly charged hydrodynamic surface at neutral pH (zetapotential ζ ∝0 mV). The formation of micron-sized agglomerates, composed of nanocrystals of 2-5 nm in size, and the subsequent precipitation cause immobilization of the major amount of Np(IV) in the Np carbonate system. Agglomeration of NpO2 nanocrystals in dependence on time was indicated by PCS and UV-vis absorption spectroscopy with the changes of baseline characteristics and absorption maximum at 742 nm. Hitherto, unknown polynuclear species as intermediate species of NpO2 nanocrystal formation were isolated from solution and observed by HR-TEM. These polynuclear Np species appear as dimers, trimers and hexanuclear compounds in analogy with those reported for other actinides. Intrinsic formation of NpO2 (fcc

  14. Galvanic Corrosion between Alloy 690 and Magnetite in Alkaline Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Soon-Hyeok Jeon

    2015-12-01

    Full Text Available The galvanic corrosion behavior of Alloy 690 coupled with magnetite has been investigated in an alkaline solution at 30 °C and 60 °C using a potentiodynamic polarization method and a zero resistance ammeter. The positive current values were recorded in the galvanic couple and the corrosion potential of Alloy 690 was relatively lower. These results indicate that Alloy 690 behaves as the anode of the pair. The galvanic coupling between Alloy 690 and magnetite increased the corrosion rate of Alloy 690. The temperature increase led to an increase in the extent of galvanic effect and a decrease in the stability of passive film. Galvanic effect between Alloy 690 and magnetite is proposed as an additional factor accelerating the corrosion rate of Alloy 690 steam generator tubing in secondary water.

  15. Electrochemistry in aqueous solution at high temperature and under pressure: study of nickel in a highly alkaline environment

    International Nuclear Information System (INIS)

    This research thesis reports the study of the corrosion resistance and anodic behaviour of various metals and alloys used in conventional thermal or nuclear power stations, more particularly the case of nickel in a highly alkaline environment (KOH 5 N) which is widely used for hydrogen production by water electrolysis. The author studied the influence of temperature and pressure on the electrochemical behaviour of nickel, and more particularly the first-oxidation kinetics. The report discusses the physicochemical and thermodynamic properties of aqueous systems at high temperature and under pressure, presents the general techniques of high-temperature electrochemistry, describes the experimental installation, and reports the development of a reference electrode which can operate in those experimental conditions. The author reports the study of the electrochemical behaviour of nickel in alkaline environment and at high temperature, reports a surface analysis performed by Auger spectroscopy, electron spectroscopy for chemical analysis or ESCA, and scanning electronic microscopy, reports the study of the electrochemical behaviour of nickel in a potassium hydroxide solution under normal temperature and pressure, but also in acid environment. Results are interpreted with respect to temperature

  16. Kinetics of oxidation of odorous sulfur compounds in aqueous alkaline solution with H2O2.

    Science.gov (United States)

    Feliers, C; Patria, L; Morvan, J; Laplanche, A

    2001-10-01

    Sulfur species oxidation is a crucial issue wastewater treatment. The production of sulfur compounds like H2S,CH3SH, C2H5SH, disulfides and dimethyle sulfide generates odorous nuisances for the neighborhood. The oxidation of these species by H2O2 in alkaline solution has been investigated. The results showed that thiols CH3SH and C2H5SH react with H202 only in their dissociated form RS- with rate constants respectively k = 8.81 +/- 0.48 M-1s-1 and 8.37 +/- 0.63 M-1.s-1. Mercaptans oxidation produces 100 % of dimethyldisulfide or diethyldisulfide. The oxidation of disulfides shows a difference of reactivity between H2O2 and HO2- towards sulfur species. Increasing the pH accelerates significantly the reactions in the case of CH3SSCH3. The oxidation rate can be described as: r = k[RSSR][H2O2][RSSR][H2O2] + k[RSSR][HO2-] [RSSR][HO2-] with k[RSSR][H2O2] = 1.2 x 10(-4) +/- 0.2 x 10(-4) M-1s-1 and k[RSSR][HO2-] = 3.4 x 10(-4) +/- 0.6 x 10(-4) M-1.s-1 for CH3SSCH3. Dimethyl sulfide presents a reactivity different from disulfides. The oxidation rate can also be described as: r = k[CH3SCH3][H2O21][CH3SCH3][H2O2] + k[CH3SCH3][HO-] [CH3SCH3][HO2-], however, oxidation rate decreases with pH increase. k[CH3SCH3][H2O2] = 12.8 x 10(-3) +/- 0.96 x 10(-3) M-1.s-1 and k[CH3SCH3][HO2-] = 4 x 10(-3) +/- 0.3 x 10(-3) M-1.s-1.

  17. Investigation into the Formation of Nanoparticles of Tetravalent Neptunium in Slightly Alkaline Aqueous Solution

    OpenAIRE

    Husar, Richard

    2015-01-01

    Considering the worldwide growing discharge of minor actinides and the current need for geological disposal facilities for radioactive waste, this work provides a contribution to the safety case concerning Np transport if it would be released from deep repository sites and moving from alkaline cement conditions (near-field) to more neutral environmental conditions (far-field). The reducing conditions in a nuclear waste repository render neptunium tetravalent, which is assumed to be immobile i...

  18. Redox switching and oxygen evolution at hydrous oxyhydroxide modified nickel electrodes in aqueous alkaline solution: effect of hydrous oxide thickness and base concentration

    OpenAIRE

    Lyons, Michael

    2012-01-01

    Outstanding issues regarding the film formation, the redox switching reaction and the oxygen evolution reaction (OER) electrocatalytic behaviour of multi-cycled nickel oxy-hydroxide films in aqueous alkaline solution have been discussed. The oxide is grown using a repetitive potential multi-cycling technique, and the mechanism of the latter hydrous oxide formation process has been discussed. A duplex layer model of the oxide/solution interphase region is proposed. The acid/base behaviour of t...

  19. Preparation, stability, and structural characterization of plutonium(VII) in alkaline aqueous solution.

    Science.gov (United States)

    Antonio, Mark R; Williams, C W; Sullivan, James A; Skanthakumar, S; Hu, Yung-Jin; Soderholm, L

    2012-05-01

    A freshly prepared solution of Pu(VI) in 2 M NaOH was oxidized to Pu(VII), via ozonolysis, while simultaneously collecting X-ray absorption spectra. Analyses of the XANES (X-ray absorption near edge structure) and EXAFS (extended X-ray absorption fine structure) data, acquired throughout the in situ experiments, show a dioxo coordination environment for Pu(VI), PuO(2)(2+), typical for it and the hexavalent actinyl species of U and Np, and its evolution into a tetraoxo-coordination environment for Pu(VII), PuO(4)(-), like that known for Np(VII). The EXAFS data provide average Pu-O distances of 1.79(1) and 1.88(1) Å, respectively. The second coordination shells, also fit as O atoms, provide Pu-O distances of 2.29-2.32 Å that are independent of the Pu oxidation state. The coordination numbers for the distant O atoms in sums with those for the nearest O atoms are consistent with 6-O environments for both Pu(VI) and Pu(VII) ions in accordance with their previously proposed speciation as [Pu(VI)O(2)(OH)(4)](2-) and [Pu(VII)O(4)(OH)(2)](3-), respectively. This solution speciation accounts precisely for the Pu(VI) and Pu(VII) coordination environments reported in various solid state structures. The Pu(VII) tetraoxo-dihydroxo anion was found to have a half-life of 3.7 h. Its instability is attributed to spontaneous reduction to Pu(VI) and not to a measurable extent of disproportionation. We found no direct evidence for Pu(VIII) in the X-ray data and, furthermore, the stoichiometry of the oxidation of Cr(III) by Pu is consistent with that expected for a valence-pure Pu(VII) preparation by ozonation and, in turn, stoichiometrically equivalent to the established Np(VII)/Cr(III) redox reaction. PMID:22524489

  20. Formation of ozone in the reaction between the ozonide radical ion, O3-, and the carbonate radical ion, CO3-, in aqueous alkaline solutions

    International Nuclear Information System (INIS)

    Ozone forms in aqueous alkaline solutions by a reaction between the O3- and CO3- radical ions. This reaction has been demonstrated under conditions favorable for the generation of suitable concentrations of these ions by a high-pressure pulse radiolysis technique. The reaction is O3- + CO3- → O3 + CO32-. Its rate constant k/sub (O3-+CO3-)/ of (6 +- 2) x 107 dm3 mol-1 s-1 has been determined by computer simulation of the reactions involved

  1. Room temperature phosphorescence lifetime and quantum yield of erythrosine B and rose bengal in aerobic alkaline aqueous solution

    International Nuclear Information System (INIS)

    The room-temperature phosphorescence behavior of erythrosine B (ER) and rose bengal (RB) in aerobic aqueous solution at pH 10 (10−4 M NaOH) is investigated. The samples were excited with sliced second harmonic pulses of a Q-switched Nd:glass laser. A gated photomultiplier tube was used for instantaneous fluorescence signal discrimination and a digital oscilloscope was used for signal recording. For phosphorescence lifetime measurement the oscilloscope response time was adjusted to appropriate time resolution and sensitivity by the ohmic input resistance. In the case of phosphorescence quantum yield determination the gated photomultiplier – oscilloscope arrangement was operated in integration mode using 10 MΩ input resistance. Phosphorescence quantum yield calibration was achieved with erythrosine B and rose bengal doped starch films of known quantum yields. The determined phosphorescence lifetimes (quantum yields) of ER and RB in 0.1 mM NaOH are τP=1.92±0.1 μs (φP=(1.5±0.3)×10−5) and 2.40±0.1 μs ((5.7±0.9)×10−5), respectively. The results are discussed in terms of triplet state deactivation by dissolved molecular oxygen. - Highlights: ► Phosphorescence lifetime of fluorone dyes in aerobe aqueous solution is measured. ► Phosphorescence quantum yield of fluorone dyes in aerobe solution is determined. ► Experimental setup with Q-switched laser and gated PMT detection is described. ► Phosphorescence quenching by dissolved molecular oxygen is analyzed. ► Absorption and fluorescence behavior of fluorones in aqueous solution is studied.

  2. An optimization study on removal of Zn from aqueous solution by ultrasound assisted preparation of activated carbon from alkaline impregnated hazelnut shell

    International Nuclear Information System (INIS)

    Nowadays, ultrasound has gained importance in a wide variety of industrial fields especially in wastewater and sewage treatment. Ultrasound exhibits several beneficial effects in solid liquid systems by means of the cavitations phenomenon by causing the formation of many microcracks on the solid surface; thus, it increases the surface area between the reactants and cleans solid reactant or catalyst particle surfaces. In this study, activated carbon adsorbent for removing heavy metal cations such as Zn2+ from aqueous solutions has been prepared. For this purpose, KOH solution was impregnated into hazelnut shells under ultrasonic irradiation. After filtration, hazelnut shells have been carbonized under inert N2 atmosphere. The experiments were planned by statistical design methods. Finally, activated carbons were characterized by the evolution of their zinc adsorption capacity. Optimum preparation conditions were obtained by using constrained optimization program by means of the Matlab computer software. Activated carbon with the maximum adsorption capacity was further characterized by using scanning electron microscopy. The alkaline impregnation into hazelnut shells under ultrasonic irradiation was found to be beneficial for preparation of activated carbon for use as adsorbents to remove Zn2+ from aqueous solutions. (author)

  3. Amino-functionalized alkaline clay with cationic star-shaped polymer as adsorbents for removal of Cr(VI) in aqueous solution

    Science.gov (United States)

    Pan, Yuanfeng; Cai, Pingxiong; Farmahini-Farahani, Madjid; Li, Yiduo; Hou, Xiaobang; Xiao, Huining

    2016-11-01

    Pentaerythritol (PER) was esterified with 2-bromoisobutyryl bromide to synthesize a four-arm initiator 4Br-PER for atom transfer radical polymerization (ATRP). Star-shaped copolymers (P(AM-co-DMAEMA)4, CSP) were prepared via ATRP using dimethyl aminoethyl methacrylate (DMAEMA) and acrylamide (AM) as comonomers, while Br-PER and CuBr/2,2‧-bipyridine (BPY) as the initiator and the catalyst, respectively. The resulting four-arm initiator and star-shaped polymer (CSP) were characterized with FT-IR, 1H NMR and Ubbelohde viscometry. Alkaline clay (AC) was immobilized with CSPs to yield amino groups, and the cationic star polymer-immobilized alkaline clay (CSP-AC) was applied to remove Cr(VI) from the aqueous solution in batch experiments. Various influencing factors, including pH, contact time and immobilization amount of CSP on adsorption capacity of CSP-AC for Cr(VI) were also investigated. The results demonstrated that Cr(VI) adsorption was highly pH dependent. The optimized pH value was 4.0. The adsorption isotherms of the adsorbent fit the Langmuir model well, with the maximum adsorption capacity of 137.9 mg/g at 30 °C. The material should be a promising adsorbent for Cr(VI) removal, with the advantages of high adsorption capacity.

  4. Alkaline earth cation extraction from acid solution

    Science.gov (United States)

    Dietz, Mark; Horwitz, E. Philip

    2003-01-01

    An extractant medium for extracting alkaline earth cations from an aqueous acidic sample solution is described as are a method and apparatus for using the same. The separation medium is free of diluent, free-flowing and particulate, and comprises a Crown ether that is a 4,4'(5')[C.sub.4 -C.sub.8 -alkylcyclohexano]18-Crown-6 dispersed on an inert substrate material.

  5. Aqueous polyethylene oxide solutions

    International Nuclear Information System (INIS)

    A number of aspects concerning the reorientation of polymer, water and ion hydration complexes have been studied in aqueous solution of polyethylene oxide (PEO). The polymer dynamics are investigated by 1H-PEO and 13C-PEO nuclear relaxation experiments. 162 refs.; 30 figs.; 19 tabs

  6. Treatment of Aqueous Solutions

    NARCIS (Netherlands)

    Van Spronsen, J.; Witkamp, G.J.

    2013-01-01

    The invention is directed to a process for the recovery or removal of one or more crystallizable compounds from an aqueous solution containing, apart from the said crystallizable compounds, one or more organic or inorganic scale- forming or scale-inducing materials having a lower solubility in water

  7. Investigation of the reaction of the ozonide ion with neptunium (VI) ions in aqueous alkaline solutions by the method of pulse radiolysis

    International Nuclear Information System (INIS)

    The method of pulse radiolysis with spectrophotometric recording of short-lived particles is used to investigate the kinetics of the reactions of O3- ion-radicals with Np(V) and Np(VI) in alkaline solutions. The rate constant of the first reaction is equal to (2.0 ± 0.3)·106, and of the second, (2.1 ± 0.2)·105 liter/(mole·sec) in 0.2-2.0 M LiOH. The peculiarities of γ-radiolysis of Np(VI) in alkaline solutions containing N2O and in aerated solutions containing K2S2O8 are elucidated. The yield of Np(VII) is determined by the behavior of O3-, which depends on the concentration of Np(VI) and OH-

  8. Technetium recovery from high alkaline solution

    Science.gov (United States)

    Nash, Charles A.

    2016-07-12

    Disclosed are methods for recovering technetium from a highly alkaline solution. The highly alkaline solution can be a liquid waste solution from a nuclear waste processing system. Methods can include combining the solution with a reductant capable of reducing technetium at the high pH of the solution and adding to or forming in the solution an adsorbent capable of adsorbing the precipitated technetium at the high pH of the solution.

  9. Influence of acid and alkaline sources on optical, structural and photovoltaic properties of CdSe nanoparticles precipitated from aqueous solution

    Science.gov (United States)

    Coria-Monroy, C. Selene; Sotelo-Lerma, Mérida; Hu, Hailin

    2016-06-01

    CdSe is a widely researched material for photovoltaic applications. One of the most important parameters of the synthesis is the pH value, since it determines the kinetics and the mechanism of the reaction and in consequence, the optical and morphological properties of the products. We present the synthesis of CdSe in solution with strict control of pH and the comparison of ammonia and KOH as alkaline sources and diluted HCl as acid medium. CdSe formation was monitored with photoluminescence emission spectra (main peak in 490 nm, bandgap of CdSe nanoparticles). XRD patterns indicated that CdSe nanoparticles are mainly of cubic structure for ammonia and HCl, but the hexagonal planes appear with KOH. Product yield decreases with pH and also decreases with KOH at constant pH value since ammonia has a double function, as complexing agent and alkaline source. Changes in morphology were observed in SEM images as well with the different alkaline source. The effect of alkaline sources on photovoltaic performance of hybrid organic solar cells with CdSe and poly(3-hexylthiophene) as active layers was clearly observed, indicating the importance of synthesis conditions on optoelectronic properties of promising semiconductor nanomaterials for solar cell applications.

  10. Electrochemical characterization of the LiCoO{sub 2}/acetylene carbon ratios for porous electrodes in alkaline lithium aqueous solutions by electrochemical impedance spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Castaneda, H., E-mail: castanedah@battelle.or [Battelle Memorial Institute, 505 King Avenue, Columbus OH, 43201 (United States); Tan, B.; Saunders, J. [Battelle Memorial Institute, 505 King Avenue, Columbus OH, 43201 (United States)

    2010-05-01

    LiCoO{sub 2} electrodes were fabricated with different acetylene carbon (AC) additions and fixed binder content. Subsequent electrochemical testing showed different processes at the interface that are related to pore distribution and electrode composition. Electrochemical impedance spectroscopy characterized the mechanisms close to open circuit conditions. The active state, combined with diffusion mechanisms within the cylindrical pores, contributed to the functionality of the particles according to the LiCoO{sub 2}/AC content, and surface characteristics of the electrode influenced the impedance distribution. The de Levie theory for porous electrode was used to describe the influence of the LiCoO{sub 2}/AC ratios in the impedance distribution when exposed to alkaline aqueous electrolytes (LiOH + Li{sub 2}SO{sub 4}). The pore model helped relate physical properties of the composite material, such as pore count, pore length, and double layer capacitance, with the mechanisms present at the interface. The theoretical model was validated with experimental data and the fitting process resulted in good agreement.

  11. Formation of ozone in the reaction between the ozonide radical ion, O/sub 3//sup -/, and the carbonate radical ion, CO/sub 3//sup -/, in aqueous alkaline solutions. [Electron beams

    Energy Technology Data Exchange (ETDEWEB)

    Holcman, J.; Sehested, K.; Bjergbakke, E.; Hart, E.J.

    1982-05-27

    Ozone forms in aqueous alkaline solutions by a reaction between the O/sub 3//sup -/ and CO/sub 3//sup -/ radical ions. This reaction has been demonstrated under conditions favorable for the generation of suitable concentrations of these ions by a high-pressure pulse radiolysis technique. The reaction is O/sub 3//sup -/ + CO/sub 3//sup -/ ..-->.. O/sub 3/ + CO/sub 3//sup 2 -/. Its rate constant k/sub (O/sub 3//sup -/+CO/sub 3//sup -/)/ of (6 +- 2) x 10/sup 7/ dm/sup 3/ mol/sup -1/ s/sup -1/ has been determined by computer simulation of the reactions involved.

  12. Photolysis of Periodate and Periodic Acid in Aqueous Solution

    DEFF Research Database (Denmark)

    Sehested, Knud; Kläning, U. K.

    1978-01-01

    The photochemistry of periodate and periodic acid in aqueous solution was studied (i) by quantum yield measurements at low light intensity (ii) by flash photolysis, and (iii) by photolysis of glassy samples at 77 K. The photochemical studies were supplemented with pulse radiolysis studies...... of aqueous periodate solutions and with kinetic studies using stopped-flow technique. In strongly alkaline solution the photodecomposition of periodate proceeds via formation of O– and IVI. At pH

  13. A Revisit to the Corrosion Inhibition of Aluminum in Aqueous Alkaline Solutions by Water-Soluble Alginates and Pectates as Anionic Polyelectrolyte Inhibitors

    Directory of Open Access Journals (Sweden)

    Refat Hassan

    2013-01-01

    Full Text Available The corrosion behavior of aluminum (Al in alkaline media in presence of some natural polymer inhibitors has been reinvestigated. The inhibition action of the tested inhibitors was found to obey both Langmuir and Freundlich isotherms models. The inhibition efficiency was found to increase with increasing the inhibitors concentration and decrease with increasing the temperature, suggesting physical adsorption mechanism. Factors such as the concentration and geometrical structure of the inhibitor, concentration of the corrosive medium, and temperature affecting the corrosion rates were examined. The kinetic parameters were evaluated, and a suitable corrosion mechanism consistent with the kinetic results obtained is suggested and discussed.

  14. 2010 Water & Aqueous Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Dor Ben-Amotz

    2010-08-13

    Water covers more than two thirds of the surface of the Earth and about the same fraction of water forms the total mass of a human body. Since the early days of our civilization water has also been in the focus of technological developments, starting from converting it to wine to more modern achievements. The meeting will focus on recent advances in experimental, theoretical, and computational understanding of the behavior of the most important and fascinating liquid in a variety of situations and applications. The emphasis will be less on water properties per se than on water as a medium in which fundamental dynamic and reactive processes take place. In the following sessions, speakers will discuss the latest breakthroughs in unraveling these processes at the molecular level: Water in Solutions; Water in Motion I and II; Water in Biology I and II; Water in the Environment I and II; Water in Confined Geometries and Water in Discussion (keynote lecture and poster winners presentations).

  15. EXTRACTION OF BETULIN BY ALIPHATIC ALCOHOLS C3-C4 FROM AN EXTERNAL LAYER OF A BIRCH BARK HYDROLYZED IN AQUEOUS ALKALINE SOLUTION

    Directory of Open Access Journals (Sweden)

    Владимир Александрович Левданский

    2014-09-01

    Full Text Available It was established, that after hydrolysis of birch bark in water solution of alkali in the presence of isopropanol, butanol and isobutanol two layers were formed. The top layer contained betulin dissolved in alcohol, and the bottom layer contained a water-soluble alkali and its hydrolysis products of bark. Betulin was isolated by the separation and concentration of the alcohol layer. The structure of betulin was confirmed by methods of IR and NMR spectroscopy.

  16. Progress of research on the influence of alkaline cation and alkaline solution on bentonite properties

    International Nuclear Information System (INIS)

    Based on the previous laboratory studies and numerical simulation on bentonite in alkaline environments, the effects of alkaline cation and alkaline solution on mineral composition, microstructure, swelling capacity and hydraulic properties of bentonite are emphasized in this paper, temperature, pH values and concentration are discussed as main affecting factors. When bentonite is exposed to alkaline cation or alkaline solution, microstructure of bentonite will be changed due to the dissolution of montmorillonite and the formation of secondary minerals, which results in the decrease of swelling pressure. The amount of the reduction of swelling pressure depends on the concentration of alkaline solution. Temperature, polyvalent cation, salinity and concentration are the main factors affecting hydraulic properties of bentonite under alkaline conditions. Therefore, future research should focus on the mechanism of coupling effects of weak alkaline solutions on the mineral composition, microstructure, swelling capacity and hydraulic properties of bentonite under different temperatures and different pH values. (authors)

  17. Determination of bisphenol A in thermal printing papers treated by alkaline aqueous solution using the combination of single-drop microextraction and HPLC.

    Science.gov (United States)

    Gao, Leihong; Zou, Jing; Liu, Haihong; Zeng, Jingbin; Wang, Yiru; Chen, Xi

    2013-04-01

    A method for the quantitative determination of bisphenol A in thermal printing paper was developed and validated. Bisphenol A was extracted from the paper samples using 2% NaOH solution, then the extracted analyte was enriched using single-drop microextraction followed by HPLC analysis. Several parameters relating to the single-drop microextraction efficiency including extraction solvent, extraction temperature and time, stirring rate, and pH of donor phase were studied and optimized. Spiked recovery of bisphenol A at 20 and 5 mg/g was found to be 95.8 and 108%, and the method detection limit and method quantification limit was 0.03 and 0.01 mg/g, respectively. Under the optimized conditions, the proposed method was applied to the determination of bisphenol A in seven types of thermal printing paper samples, and the concentration of bisphenol A was found in the range of 0.53-20.9 mg/g. The considerably minimum usage of organic solvents (5 μL 1-octanol) and high enrichment factor (189-197) in the sample preparation are the two highlighted advantages in comparison with previously published works.

  18. Radiolysis of Aqueous Toluene Solutions

    International Nuclear Information System (INIS)

    Aqueous toluene solutions have been irradiated with Co γ-rays. In unbuffered solutions the various cresol isomers are formed in a total yield of 0.45, 0.87 and 0.94 molecules/100 eV absorbed energy in argon-, N2O- and air - saturated solutions, respectively. The yields are reduced in acid (pH 3) solutions (G 0.14, 0.14 and 0.52, respectively) but the reduction is compensated by the formation of 1,2-di-phenylethane in yields of 0.49 and 1.60 in argon- and N2O-saturated solutions, respectively. Benzyl radicals are formed through an acid catalysed water elimination reaction from the initially formed hydroxymethylcyclohexadienyl radical. Phenyltolylmethanes, dimethylbiphenyls and partly reduced dimers are also formed during the radiolysis. Hydrogen is formed in the same yield as the molecular yield, g(H2). Xylene isomers and benzene are formed in trace quantities. The most remarkable effects of the addition of Fe(III) ions to deaerated acid toluene solutions are the formation of benzyl alcohol and benzaldehyde and an increase in the yield of 1,2-diphenylethane

  19. DEHYDRATION CONDENSATION IN AQUEOUS SOLUTION

    Energy Technology Data Exchange (ETDEWEB)

    Steinman, Gary; Kenyon, Dean H.; Calvin, Melvin

    1965-04-01

    EARLIER investigations have demonstrated that di-cyandiamide (DCDA), the dimer of cyanamide, can successfully promote the dehydration condensation of: (1) glucose and orthophosphate to give glucose-6-phosphate; (2) adenosine and orthophosphate to give adenosine-5'-monophosphate; (3) orthophosphate to give pyrophosphate; (4) alanine to give alanylalanine and alanylalanylalanine. These reactions were carried out in dilute aqueous solutions in the dark. (It was also demonstrated that the combination of ultra-violet light and dicyandiamide could promote the synthesis of dipeptides. This observation has since been confirmed by other investigators.) These experiments were designed to demonstrate one possible means by which such compounds could have been formed on the prebiotic Earth, thus providing materials needed for the origin of living systems. Dicyandiamide itself could have been, present on the primitive Earth as was demonstrated with the ultra-violet irradiation of cyanide solution.

  20. Radiolysis of Aqueous Benzene Solutions

    International Nuclear Information System (INIS)

    Aerated and deaerated aqueous solutions of benzene have been irradiated with 60Co γ-rays. The products of radiolysis in deaerated, unbuffered or acid, solutions were phenol, biphenyl, hydrogen and in acid solutions also hydrogen peroxide with the following yields: G(phenol) = 0. 37 (0. 37), G(biphenyl) = 1.3 (1.7), G(H2) = 0.44 (0. 43) and G(H2O2) = 0 (0.60), the figures in brackets giving the results for acid solutions. The results are shown to agree with the conclusion that k(e-aq + H2O2) >> k(H + H2O2). Furthermore, the results indicate that a competition takes place between the reactions: 2 C6H6OH · -> dimer -> biphenyl. C6H7 · + C6H6OH · -> dimer -> biphenyl. The yields in aerated, unbuffered or acid, solutions were: G(phenol) = 2.1 (2.3), G(biphenyl) = 0 (0), and G(H2O2) = 2.2 (3.1), the figures in brackets being valid for acid solutions. The ratio k(H + C6H6)/k(H + O2) was 1.4x10-2. The results indicate that peroxides, or more probably hydroperoxides, take part in the reactions. After the addition of Fe2+ or Fe3+ to aerated acid solutions G(phenol) was increased to 6.6 and 3.4 respectively. Oxygen was consumed more rapidly in the presence of Fe. Reaction mechanisms are discussed

  1. Revisiting zinc passivation in alkaline solutions

    International Nuclear Information System (INIS)

    Highlights: • Zinc passive films were characterised by electrochemical tests coupled with cross sectional FIB-SEM. • Passive layers at pH > 12 comprised of an outer precipitated layer and inner compact oxide. • The electrolyte pH influences the nature/stability of the outer precipitated layer and this impacts the passive state on zinc. • The precipitated layers on zinc at pH 12 support cathode reactions and catalyse oxide growth. -- Abstract: Passive films nominally consist of an inner compact oxide and the outer precipitated layer. In the case of zinc (Zn), the outer layer is mainly precipitated ZnO/Zn(OH)2. Electrolyte pH controls the stability of the outer precipitated layer. In a pH 13 solution, formation of soluble Zn(OH)3− and Zn(OH)42− phases render the precipitated layer unstable increasing zinc corrosion, whereas at pH 12, the precipitated layer (ZnO/Zn(OH)2) is more stable making it an effective anodic barrier upon zinc. These precipitated oxides formed at pH 12 support cathodic reactions on their surface which in turn catalyse further oxide growth by a cathodically driven process. Focused ion beam-scanning electron microscopy (FIB-SEM) was used to support some of the electrochemical assertions, revealing the form and morphology of the passive layers that grow upon zinc exposed to alkaline solutions

  2. Modeling reactive geochemical transport of concentrated aqueous solutions

    Science.gov (United States)

    Zhang, Guoxiang; Zheng, Zuoping; Wan, Jiamin

    2005-02-01

    Aqueous solutions with ionic strength larger than 1 M are usually considered concentrated aqueous solutions. These solutions can be found in some natural systems and are also industrially produced and released into accessible natural environments, and as such, they pose a big environmental problem. Concentrated aqueous solutions have unique thermodynamic and physical properties. They are usually strongly acidic or strongly alkaline, with the ionic strength possibly reaching 30 M or higher. Chemical components in such solutions are incompletely dissociated. The thermodynamic activities of both ionic and molecular species in these solutions are determined by the ionic interactions. In geological media the problem is further complicated by the interactions between the solutions and sediments and rocks. The chemical composition of concentrated aqueous solutions when migrating through the geological media may be drastically altered by these strong fluid-rock interactions. To effectively model reactive transport of concentrated aqueous solutions, we must take into account the ionic interactions. For this purpose we substantially extended an existing reactive transport code, BIO-CORE2D©, by incorporating a Pitzer ion interaction model to calculate the ionic activity. In the present paper, the model and two test cases of the model are briefly introduced. We also simulate a laboratory column experiment in which the leakage of highly alkaline waste fluid stored at Hanford (a U.S. Department of Energy site, located in Washington State) was studied. Our simulation captures the measured pH evolution and indicates that all the reactions controlling the pH evolution, including cation exchanges and mineral dissolution/precipitation, are coupled.

  3. Nanoporous activated carbon cloth for capacitive deionization of aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Oh, Han-Jun [Department of Materials Science, Hanseo University, Seosan, 352-820 (Korea, Republic of); Lee, Jong-Ho [Department of Chemistry, Hanseo University, Seosan, 352-820 (Korea, Republic of); Ahn, Hong-Joo [Korea Atomic Energy Research Institute, Daejeon, 305-600 (Korea, Republic of); Jeong, Yongsoo [Korea Institute of Machinery and Materials, Changwon, 641-010 (Korea, Republic of); Kim, Young-Jig [Department of Metallurgical Engineering, Sungkyunkwan University, Suwon, 440-746 (Korea, Republic of); Chi, Choong-Soo [School of Advanced Materials Engineering, Kookmin University, Seoul, 136-702 (Korea, Republic of)]. E-mail: cschi@kookmin.ac.kr

    2006-09-25

    Activated nanostructured-carbon cloths with a high ratio of surface area to volume are used as electrode for capacitive deionization. The electrochemical properties on capacitive deionization for NaCl solution have been investigated to improve efficiency of capacitive deionization properties from aqueous solution, employing chemical surface-modification by etching in alkaline and acidic solution. The removal efficiency of inorganic salts of activated carbon cloths by chemical modification significantly increased. Specially the carbon cloth surface modified in HNO{sub 3} showed an effect of improvement in the CDI efficiency due to not only ion adsorption by an electric double layer, but also electron transfer by Faradaic reaction.

  4. Recombination of Geminate (OH,eaq-) Pairs in Concentrated Alkaline Solutions: Lack of Evidence For Hydroxyl Radical Deprotonation

    CERN Document Server

    Lian, R; Shkrob, I A; Bartels, D M; Oulianov, D A; Gosztola, D J; Lian, Rui; Crowell, Robert A.; Shkrob, Ilya A.; Bartels, David M.; Oulianov, Dmitri A.; Gosztola, David

    2004-01-01

    Picosecond dynamics of hydrated electrons and hydroxyl radicals generated in 200 nm photodissociation of aqueous hydroxide and 400 nm (3-photon) ionization of water in concentrated alkaline solutions were obtained. No deprotonation of hydroxyl radicals was observed on sub-nanosecond time scale, even in 1-10 M KOH solutions. This result is completely at odds with the kinetic data for deprotonation of OH radical in dilute alkaline solutions. We suggest that the deprotonation of hydroxyl radical is slowed down dramatically in concentrated alkaline solutions.

  5. γ-radiation induced tetracycline removal in an aqueous solution

    International Nuclear Information System (INIS)

    Degradation effect of tetracycline (TC) by γ-radiation was investigated in an aqueous solution. The effects of initial concentrations of TC, pH values, combining with H2O2 or CH3OH on degradation of TC were studied. Results showed that TC can be effectively degradated by γ-irradiation in an aqueous solution. Degradation of TC could be remarkably improved both in acid solution and alkaline solution, especially when pH value was 9.0. In addition, H2O2 could gently promote degradation of TC induced by γ-radiation. While, CH3OH markedly restrained degradation of TC induced by γ-radiation. The degradation mechanism of TC was supposed by results of quantum chemical calculations and LC-MS. Results proved that degradation of TC induced by γ-radiation was mainly ascribed to · OH oxidation. (authors)

  6. The aluminum chemistry and corrosion in alkaline solutions

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Jinsuo [International Nuclear System Engineering, MS-K 575, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)], E-mail: jszhang@lanl.gov; Klasky, Marc; Letellier, Bruce C. [International Nuclear System Engineering, MS-K 575, Los Alamos National Laboratory, Los Alamos, NM 87545 (United States)

    2009-02-15

    Aluminum-alkaline solution systems are very common in engineering applications including nuclear engineering. Consequently, a thorough knowledge of the chemistry of aluminum and susceptibility to corrosion in alkaline solutions is reviewed. The aluminum corrosion mechanism and corrosion rate are examined based on current experimental data. A review of the phase transitions with aging time and change of environment is also performed. Particular attention is given to effect of organic and inorganic ions. As an example, the effect of boron is examined in detail because of the application in nuclear reactor power systems. Methods on how to reduce the corrosion rate of aluminum in alkaline solutions are also highlighted.

  7. Comparison of alkaline industrial wastes for aqueous mineral carbon sequestration through a parallel reactivity study.

    Science.gov (United States)

    Noack, Clinton W; Dzombak, David A; Nakles, David V; Hawthorne, Steven B; Heebink, Loreal V; Dando, Neal; Gershenzon, Michael; Ghosh, Rajat S

    2014-10-01

    Thirty-one alkaline industrial wastes from a wide range of industrial processes were acquired and screened for application in an aqueous carbon sequestration process. The wastes were evaluated for their potential to leach polyvalent cations and base species. Following mixing with a simple sodium bicarbonate solution, chemistries of the aqueous and solid phases were analyzed. Experimental results indicated that the most reactive materials were capable of sequestering between 77% and 93% of the available carbon under experimental conditions in four hours. These materials - cement kiln dust, spray dryer absorber ash, and circulating dry scrubber ash - are thus good candidates for detailed, process-oriented studies. Chemical equilibrium modeling indicated that amorphous calcium carbonate is likely responsible for the observed sequestration. High variability and low reactive fractions render many other materials less attractive for further pursuit without considering preprocessing or activation techniques.

  8. Interfacial Thermodynamics of Coexisting Aqueous Polymer Solutions

    NARCIS (Netherlands)

    Vis, M.

    2015-01-01

    Phase separation is commonly observed when two different polymers are present in aqueous solution, forming aqueous two-phase systems which typically consist for 90% of water. It is demonstrated that the presence of charge on one of the polymers results in an electric potential difference between the

  9. Kinetics of ptaquiloside hydrolysis in aqueous solution

    DEFF Research Database (Denmark)

    Ayala-Luis, Karina B.; Bildsøe Hansen, Pernille; Rasmussen, Lars Holm;

    2006-01-01

    of the toxin, a full understanding of the PTA degradation in aqueous environments is important. The kinetics of PTA hydrolysis was examined at 22C in aqueous buffered solutions (pH 2.88–8.93). The reaction was found to follow first-order kinetics with respect to PTA at all pH and temperature conditions. At p...

  10. Tannin (Polyphenol) Stability in Aqueous Solutions

    Science.gov (United States)

    Understanding the chemical stability of tannins (polyphenolics) in soils is critical to understanding their biological activities and fate. We examined the stability of chemically defined tannins in aqueous solutions under conditions simulating natural and laboratory conditions. We evaluated tanni...

  11. Calorimetric studies of macromolecular aqueous solutions

    NARCIS (Netherlands)

    Blandamer, M.J; Cullis, P.M.; Engberts, J.B.F.N.

    1996-01-01

    Both titration and differential scanning microcalorimetric techniques are shown to yield important information concerning the properties of macromolecules in aqueous solution. Application of titration calorimetry is examined in me context of deaggregation of canonic micelles (e.g. hexadecyltrimethyl

  12. KINETICS OF THE HYDROXYPROPYLATION OF POTATO STARCH IN AQUEOUS-SOLUTION

    NARCIS (Netherlands)

    LAMMERS, G; STAMHUIS, EJ; BEENACKERS, AACM

    1993-01-01

    Kinetic results are presented for the hydroxypropylation of Potato starch with methyloxirane in aqueous solution. Reaction temperatures were varied from 303 to 362 K. Sodium hydroxide was used as a catalyst. The overall conversion rate of methyloxirane in alkaline starch solution is determined by th

  13. Study of the physicochemical properties of the interface between titanium dioxide and various aqueous solutions

    International Nuclear Information System (INIS)

    The aim of this work is the study of ion exchange capacity of titanium dioxide in view of high temperature water purification and radioactive effluent processing because of its resistance to heat and radiations. Titanium dioxide is obtained by alkaline hydrolysis of an aqueous solution of Ti (IV) and is characterized by analytical physical chemistry methods. Interface between Ti02 and simple aqueous solutions (electrolytes) is more particularly studied by potentiometry

  14. Precipitation of neptunium dioxide from aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Roberts, K E

    1999-12-01

    Tens of thousands of metric tons of highly radioactive, nuclear waste have been generated in the US. Currently, there is no treatment or disposal facility for these wastes. Of the radioactive elements in high-level nuclear waste, neptunium (Np) is of particular concern because it has a long half-life and may potentially be very mobile in groundwaters associated with a proposed underground disposal site at Yucca Mountain, Nevada. Aqueous Np concentrations observed in previous, short-term solubility experiments led to calculated potential doses exceeding proposed long-term regulatory limits. However, thermodynamic data for Np at 25 C showed that these observed aqueous Np concentrations were supersaturated with respect to crystalline NpO{sub 2}. It was hypothesized that NpO{sub 2} is the thermodynamically stable solid phase in aqueous solution, but it is slow to form in an aqueous solution of NpO{sub 2}{sup +} on the time scale of previous experiments. The precipitation of NpO{sub 2} would provide significantly lower aqueous Np concentrations leading to calculated doses below proposed regulatory limits. To test this hypothesis, solubility experiments were performed at elevated temperature to accelerate any slow precipitation kinetics. Ionic NpO{sub 2}{sup +} (aq) was introduced into very dilute aqueous solutions of NaCl with initial pH values ranging from 6 to 10. The reaction vessels were placed in an oven and allowed to react at 200 C until steady-state aqueous Np concentrations were observed. In all cases, aqueous Np concentrations decreased significantly from the initial value of 10{sup {minus}4} M. The solids that formed were analyzed by x-ray powder diffraction, x-ray absorption spectroscopy, and scanning electron microscopy. The solids were determined to be high-purity crystals of NpO{sub 2}. This is the first time that crystalline NpO{sub 2} has been observed to precipitate from NpO{sub 2}{sup +}(aq) in near-neutral aqueous solutions. The results obtained

  15. Alkaline solution absorption of carbon dioxide method and apparatus

    Science.gov (United States)

    Hobbs, D.T.

    1991-01-01

    Disclosed is a method for measuring the concentration of hydroxides (or pH) in alkaline solutions, using the tendency of hydroxides to adsorb CO{sub 2}. The method comprises passing CO{sub 2} over the surface of an alkaline solution in a remote tank before and after measurements of the CO{sub 2} concentration. Comparison of the measurements yields the adsorption fraction from which the hydroxide concentration can be calculated using a correlation of hydroxide or pH to adsorption fraction. A schematic is given of a process system according to a preferred embodiment of the invention. 2 figs.

  16. Hydrophobic Solvation: Aqueous Methane Solutions

    Science.gov (United States)

    Konrod, Oliver; Lankau, Timm

    2007-01-01

    A basic introduction to concept of a solvation shell around an apolar solute as well as its detection is presented. The hydrophobic solvation of toluene is found to be a good teaching example which connects macroscopic, phenomenological thermodynamic results with an atomistic point of view.

  17. Issues in Freeze Drying of Aqueous Solutions

    Institute of Scientific and Technical Information of China (English)

    王维; 陈墨; 陈国华

    2012-01-01

    Freeze drying or lyophilization of aqueous solutions is widely used in pharmaceutical industry. The in-creased importance Of the process is gaining a worldwide interest of research. A growing body of literature has demonstrated that the scientific approach can result in improved product quality with minimum trial and error em-piricism. Formulation and process development need a systematical understanding of the physical chemistry of freezing and freeze drying, material science and mechanisms of heat and mass transfer. This paper presents an overview on freeze ding of aqueous solutions based on publications in the past few decades. The important issuesof the process are analyzed.

  18. Qualitative aspects of the degradation of mitomycins in alkaline solution.

    Science.gov (United States)

    Beijnen, J H; den Hartigh, J; Underberg, W J

    1985-01-01

    The major degradation product in alkaline solution of mitomycin A, mitomycin C and porfiromycin is the corresponding 7-hydroxymitosane. The isolation and the physico-chemical and analytical properties of these compounds and their derivatized analogues are discussed. Data are presented on the degradation of mitomycin C at extremely high pH values. PMID:16867711

  19. Quasi-Immiscible Spreading of Aqueous Surfactant Solutions on Entangled Aqueous Polymer Solution Subphases

    OpenAIRE

    Sharma, Ramankur; Corcoran, Timothy E.; Garoff, Stephen; Przybycien, Todd M.; Swanson, Ellen R.; Tilton, Robert D.

    2013-01-01

    Motivated by the possibility of enhancing aerosol drug delivery to mucus-obstructed lungs, the spreading of a drop of aqueous surfactant solution on a physically entangled aqueous poly(acrylamide) solution subphase that mimics lung airway surface liquid was investigated. Sodium dodecyl sulfate was used as the surfactant. To visualize spreading of the drop and mimic the inclusion of a drug substance, fluorescein, a hydrophilic and non-surface active dye, was added to the surfactant solution. T...

  20. Aqueous Solution Chemistry on Mars

    Science.gov (United States)

    Quinn, R.; Hecht, M.; Kounaves, S.; Young, S.; West, S.; Fisher, A.; Grunthaner, P.

    2007-12-01

    Currently en route to Mars, the Phoenix mission carries four wet chemistry cells designed to perform basic solution chemistry on martian soil. The measurement objectives are typical of those that would be performed on an unknown sample on Earth, including detection of common anions and cations, total conductivity, pH, redox potential, cyclic voltammetry (CV), etc. Both the challenge and the novelty arise from the necessity to perform these measurements with severely constrained resources in a harsh and (literally) alien environment. Sensors for all measurements are integrated into a common "beaker," with the ability to perform a two-point calibration of some sensors using a pair of low-concentration solutions. Sulfate measurement is performed with a crude titration. While most measurements use ion selective electrodes, halide interferences are resolved by independent chronopotentiometry (CP) measurements. No preconditioning of the soil-water mixture is possible, nor is any physical characterization of the introduced soil sample beyond coarse visual inspection. Among the idiosyncrasies of the measurement is the low external pressure, which requires that the analysis be performed close to the boiling point of water under an atmosphere consisting almost entirely of water vapor. Despite these liabilities, however, extensive laboratory characterization has validated the basic approach, and protocols for both CV and CP have been developed and tested. Enhancing the value of the measurement is the suite of coordinated observations, such as microscopy and evolved gas analysis, to be performed by other Phoenix instruments.

  1. Experiences in the capture of combustion gases of rice husk with alkaline solutions

    OpenAIRE

    Abelardo Prada Matiz; Caroll Edith Cortés Castillo

    2011-01-01

    The present work is aimed at studying the processes of capture of combustion gases of rice husk with alkaline solutions of sodium hydroxide (NaOH) and potassium hydroxide (KOH) and its subsequent transformation into calcium carbonate (CaCO3), a substance useful in agriculture, by adding calcium chloride(CaCl2) in aqueous solution. Was determined the basic characteristics of the process of capture of combustion gases such as reaction time, pH, mass and performance of calcium carbonate (CaCO3) ...

  2. Radium removal from aqueous sulphate solutions

    International Nuclear Information System (INIS)

    A process for removing radium from an aqueous sulphate solution also containing magnesium is claimed. The pH of the solution is less than 10. A soluble barium salt is added to the solution to precipitate radium as barium radium sulphate. The pH of the solution is then raised to at least 11 to precipitate an insoluble magnesium compound which collects the barium radium sulphate precipitate. The precipitates are separated from the solution. If the sulphate solution contains dissolved magnesium and other impurities at a pH not greater than 7, then the first step in the process involves raising the pH of the solution to a value not greater than 10 to precipitate some of the magnesium and a substantial proportion of the other impurities and separating the precipitate from the solution. The radium removal is a step in the treatment of liquids resulting from the sulphuric acid leaching of uranium ores

  3. Aqueous solutions of ionic liquids: microscopic assembly

    NARCIS (Netherlands)

    J.M. Vicent-Luna; D. Dubbeldam; P. Gómez-Álvarez; S. Calero

    2016-01-01

    Aqueous solutions of ionic liquids are of special interest, due to the distinctive properties of ionic liquids, in particular, their amphiphilic character. A better understanding of the structure-property relationships of such systems is hence desirable. One of the crucial molecular-level interactio

  4. Water & Aqueous Solutions. Final Progress Report

    Energy Technology Data Exchange (ETDEWEB)

    None

    2002-08-09

    The Gordon Research Conference (GRC) on Water & Aqueous Solutions was held at Holderness School, New Hampshire, 8/4/02 thru 8/9/02. Emphasis was placed on current unpublished research and discussion of the future target areas in this field.

  5. SEPARATION OF SCANDIUM FROM AQUEOUS SOLUTIONS

    Science.gov (United States)

    Peppard, D.F.; Nachtman, E.S.

    1958-02-25

    This patent relates to a process for the separation of scandium from yttrium, thorium, and trivalent rare earths and with their separation from each other. It has been found that scandium and yttrium can be separated from trivalent rare earths in acidic solution, for example, a solution 6 M in HCl, by contacting with tributyl phosphate, whereupon the scandum is preferentially extracted into the organic phase, leaving the yttrium and trivalent rare earths in the aqueous phase.

  6. Mechanism of gold dissolving in alkaline thiourea solution

    Institute of Scientific and Technical Information of China (English)

    CHAI Li-yuan; WANG Yun-yan

    2007-01-01

    Reaction mechanism of gold dissolving in alkaline thiourea solution was studied by electrochemical methods, such as cyclic voltammetry, chronopotentiometry, AC impedance, linear sweep voltammetry. Apparent activation energy of anodic process of gold electrode dissolving in alkaline thiourea solution is 14.91 kJ/mol. Rate determining step is the process of gold thiourea complex diffusing away from electrode surface to solution. The results of AC impedance and chronopotentiometry indicate that thiourea adsorbs on gold electrode surface before dissolving in solution. There does not exist proceeding chemical reactions. Formamidine disulfide, the decomposed product of thiourea, does not participate the process of gold dissolution and thiourea complex. Species with electro-activity produced in the process of electrode reaction adsorbs on the electrode surface. In alkaline thiourea solution, gold dissolving mechanism undergoes the following courses: adsorption of thiourea on electrode surface; charge transfer from gold atom to thiourea molecule; Au[SC(NH2)2]ads+ receiving a thiourea molecule and forming stable Au[SC(NH2)2]2+; and then Au[SC(NH2)2]2+diffusing away from the electrode surface to solution, the last step is the rate-determining one.

  7. IUPAC-NIST Solubility Data Series. 95. Alkaline Earth Carbonates in Aqueous Systems. Part 1. Introduction, Be and Mg

    Science.gov (United States)

    De Visscher, Alex; Vanderdeelen, Jan; Königsberger, Erich; Churagulov, Bulat R.; Ichikuni, Masami; Tsurumi, Makoto

    2012-03-01

    The alkaline earth carbonates are an important class of minerals. This volume compiles and critically evaluates solubility data of the alkaline earth carbonates in water and in simple aqueous electrolyte solutions. Part 1, the present paper, outlines the procedure adopted in this volume in detail, and presents the beryllium and magnesium carbonates. For the minerals magnesite (MgCO3), nesquehonite (MgCO3.3H2O), and lansfordite (MgCO3.5H2O), a critical evaluation is presented based on curve fits to empirical and/or thermodynamic models. Useful side products of the compilation and evaluation of the data outlined in the introduction are new relationships for the Henry constant of CO2 with Sechenov parameters, and for various equilibria in the aqueous phase including the dissociation constants of CO2(aq) and the stability constant of the ion pair MCO30(aq) (M = alkaline earth metal). Thermodynamic data of the alkaline earth carbonates consistent with two thermodynamic model variants are proposed. The model variant that describes the Mg2+-HCO3- ion interaction with Pitzer parameters was more consistent with the solubility data and with other thermodynamic data than the model variant that described the interaction with a stability constant.

  8. Characterization of aqueous silver nitrate solutions for leakage tests

    Directory of Open Access Journals (Sweden)

    José Ferreira Costa

    2011-06-01

    Full Text Available OBJECTIVE: To determine the pH over a period of 168 h and the ionic silver content in various concentrations and post-preparation times of aqueous silver nitrate solutions. Also, the possible effects of these factors on microleakage test in adhesive/resin restorations in primary and permanent teeth were evaluated. MATERIAL AND METHODS: A digital pHmeter was used for measuring the pH of the solutions prepared with three types of water (purified, deionized or distilled and three brands of silver nitrate salt (Merck, Synth or Cennabras at 0, 1, 2, 24, 48, 72, 96 and 168 h after preparation, and storage in transparent or dark bottles. Ionic silver was assayed according to the post-preparation times (2, 24, 48, 72, 96, 168 h and concentrations (1, 5, 25, 50% of solutions by atomic emission spectrometry. For each sample of each condition, three readings were obtained for calculating the mean value. Class V cavities were prepared with enamel margins on primary and permanent teeth and restored with the adhesive systems OptiBond FL or OptiBond SOLO Plus SE and the composite resin Filtek Z-250. After nail polish coverage, the permanent teeth were immersed in 25% or 50% AgNO3 solution and the primary teeth in 5% or 50% AgNO3 solutions for microleakage evaluation. ANOVA and the Tukey's test were used for data analyses (α=5%. RESULTS: The mean pH of the solutions ranged from neutral to alkaline (7.9±2.2 to 11.8±0.9. Mean ionic silver content differed depending on the concentration of the solution (4.75±0.5 to 293±15.3 ppm. In the microleakage test, significant difference was only observed for the adhesive system factor (p=0.000. CONCLUSIONS: Under the tested experimental conditions and based on the obtained results, it may be concluded that the aqueous AgNO3 solutions: have neutral/alkaline pH and service life of up to 168 h; the level of ionic silver is proportional to the concentration of the solution; even at 5% concentration, the solutions were

  9. Characterization of aqueous silver nitrate solutions for leakage tests

    Science.gov (United States)

    COSTA, José Ferreira; SIQUEIRA, Walter Luiz; LOGUERCIO, Alessandro Dourado; REIS, Alessandra; de OLIVEIRA, Elizabeth; ALVES, Cláudia Maria Coelho; BAUER, José Roberto de Oliveira; GRANDE, Rosa Helena Miranda

    2011-01-01

    Objectives To determine the pH over a period of 168 h and the ionic silver content in various concentrations and post-preparation times of aqueous silver nitrate solutions. Also, the possible effects of these factors on microleakage test in adhesive/resin restorations in primary and permanent teeth were evaluated. Material and Methods A digital pHmeter was used for measuring the pH of the solutions prepared with three types of water (purified, deionized or distilled) and three brands of silver nitrate salt (Merck, Synth or Cennabras) at 0, 1, 2, 24, 48, 72, 96 and 168 h after preparation, and storage in transparent or dark bottles. Ionic silver was assayed according to the post-preparation times (2, 24, 48, 72, 96, 168 h) and concentrations (1, 5, 25, 50%) of solutions by atomic emission spectrometry. For each sample of each condition, three readings were obtained for calculating the mean value. Class V cavities were prepared with enamel margins on primary and permanent teeth and restored with the adhesive systems OptiBond FL or OptiBond SOLO Plus SE and the composite resin Filtek Z-250. After nail polish coverage, the permanent teeth were immersed in 25% or 50% AgNO3 solution and the primary teeth in 5% or 50% AgNO3 solutions for microleakage evaluation. ANOVA and the Tukey's test were used for data analyses (α=5%). Results The mean pH of the solutions ranged from neutral to alkaline (7.9±2.2 to 11.8±0.9). Mean ionic silver content differed depending on the concentration of the solution (4.75±0.5 to 293±15.3 ppm). In the microleakage test, significant difference was only observed for the adhesive system factor (p=0.000). Conclusions Under the tested experimental conditions and based on the obtained results, it may be concluded that the aqueous AgNO3 solutions: have neutral/alkaline pH and service life of up to 168 h; the level of ionic silver is proportional to the concentration of the solution; even at 5% concentration, the solutions were capable of

  10. Solubilisation of lignite during oxydesulphurization in alkaline solutions

    Energy Technology Data Exchange (ETDEWEB)

    Yaman, S.; Kuecuekbayrak, S. [Istanbul Technical Univ., Chemical Engineering Dept. (Turkey)

    1997-12-31

    Some desulphurization processes such as oxydesulphurization in which dissolved oxygen is attached to coal particles are performed usually in alkaline solutions. Therefore, these processes are resulted in not only sulphur removal but also some solubilisation of the coal matrix. In this study three different Turkish lignite samples are subjected to various oxydesulphurization processes in which dilute solutions of NaOH, Na{sub 2}CO{sub 3}, NH{sub 4}OH or Na{sub 2}B{sub 4}O{sub 7} containing dissolved oxygen under pressure were applied. The experiments were performed in a magnetically stirred and electrically heated Parr autoclave. The extent of the solubilisation is varied depending on the type and concentration of the alkaline used, the applied temperature and the rank of the lignite sample used. (orig.)

  11. A new electrochemical oscillatory system of bromate in alkaline solution

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    A new electrochemical oscillatory system of bromate in alkaline solution is reported. In PtBromate-Alkaline solution system, two different types of electrochemical oscillations (Type Ⅰ and Type Ⅱ) can be observed. Type Ⅰ appears before hydrogen evolution and Type Ⅱ involves periodic hydrogen evolution. Type Ⅰ relates to the adsorption/desorption of the hydrogen on platinum electrode, and Type Ⅱ with periodic oscillation stems from the coupling of electrochemical reactions (the reduction of bromate and evolution hydrogen reaction) with mass transfer (diffusion and convection). More over, under the right conditions, the two types appear in different oscillatory modes, for example,simple periodical mode and mixed one, etc,, Crossed cycle in the cyclic voltammograms, which is the basiccharacteristics for electrochemical oscillatory systems, has also been observed as expected.

  12. Removal of radium from aqueous sulphate solutions

    International Nuclear Information System (INIS)

    Radium is often present in ores and an aqueous solution associated with the ore may consequently contain dissolved radium. It is frequently necessary to remove radium from such solutions to reduce the total radium content to a prescribed low level before the solution can be returned to the environment. The present invention is based on the discovery that the total radium content can be reduced to a satisfactory level within a reasonable time by adding a soluble barium salt to a radium-containing sulphate solution which also contains dissolved magnesium at a pH not greater than about 0 to precipitate radium as barium radium sulphate, raising the pH to at least 11 to precipitate an insoluble magnesium compound which collects the barium radium sulphate precipitate, and separating substantially all of the precipitates from the solution

  13. Flocculation performance of a cationic biopolymer derived from a cellulosic source in mild aqueous solution.

    Science.gov (United States)

    Liimatainen, Henrikki; Sirviö, Juho; Sundman, Ola; Visanko, Miikka; Hormi, Osmo; Niinimäki, Jouko

    2011-10-01

    The flocculation behavior of cationic, quaternary ammonium groups containing cellulosic biopolymers, CDACs, synthesized by cationizing dialdehyde cellulose in mild aqueous solution was studied in a kaolin suspension. In particular, the role of CDAC dosage and solution pH, NaCl concentration, and temperature were clarified. In addition, the initial apparent charge densities (CDs), particle sizes, ζ-potential, and stability of CDs were determined. CDACs possessed a high flocculation activity in neutral and acidic solutions, but a significant decrease was observed in alkaline solutions (pH >9). This was also seen as a decline in the apparent CD and particle size of the CDACs in alkaline conditions. The measurements also indicated that the apparent CD decreased to a constant level of 3 mmol/g in aqueous solutions. However, no notable decrease in flocculation performance was obtained after several days of storage. Moreover, the variation of NaCl concentration and temperature did not affect the flocculation activity. PMID:21862324

  14. Uranyl fluoride luminescence in acidic aqueous solutions

    International Nuclear Information System (INIS)

    Luminescence emission spectra and decay rates are reported for uranyl species in acidic aqueous solutions containing HF or added NaF. The longest luminescence lifetime, 0.269 ± 0.006 ms, was observed from uranyl in 1 M HF + 1 M HClO4 at 296 K and decreased with increasing temperature. Based on a luminescence dynamics model that assumes equilibrium among electronically excited uranyl fluoride species and free fluoride ion, this long lived uranyl luminescence in aqueous solution is attributed primarily to UO2F2. Studies on the effect of added LiNO3 or Na2WO4·2H2O showed relatively weak quenching of uranyl fluoride luminescence which suggests that high sensitivity determination of the UF6 content of WF6 gas should be feasible via uranyl luminescence analysis of hydrolyzed gas samples of impure WF6

  15. Zeolites as alcohol adsorbents from aqueous solutions

    Directory of Open Access Journals (Sweden)

    Cekova Blagica

    2006-01-01

    Full Text Available The potential usage of zeolites as adsorbents for the removal of organic molecules from water was investigated in a series of experiments with aqueous solutions of lower alcohols. This could represent a simple solution to the problem of cleaning up industrial wastewater as well as recovering valuable chemicals at relatively low costs. Adsorption isotherms of the Langmuir type were applied, and calculations showed that the amount of propanol adsorbed on silicalite corresponded to approximately 70% of the pore volume. The adsorption process is simple, and recovery of the more concentrated products is easily done by heat treatment and/or at lowered pressures. Adsorption experiments with aqueous acetone showed that silicalite had approximately the same adsorption capacity for acetone as for n-propanol. Heats of adsorption were determined calorimetrically.

  16. Does Dimeric Melittin Occur in Aqueous Solutions?

    OpenAIRE

    Schubert, D; Pappert, G.; Boss, K.

    1985-01-01

    Melittin, a peptide from bee venom, is known to undergo a monomer / tetramer conversion in aqueous solutions. We have studied the possible participation of dimers in the association equilibrium of melittin by sedimentation equilibrium experiments in the analytical ultracentrifuge and subsequent mathematical analysis of the concentration distributions obtained. It was found that the dimeric state is not significantly populated, the contribution of dimer to the total peptide weight probably bei...

  17. Aqueous solution dispersement of carbon nanotubes

    Science.gov (United States)

    Kim, Jae-Woo (Inventor); Park, Cheol (Inventor); Choi, Sang H. (Inventor); Lillehei, Peter T. (Inventor); Harrison, Joycelyn S. (Inventor)

    2011-01-01

    Carbon nanotubes (CNTs) are dispersed in an aqueous buffer solution consisting of at least 50 weight percent water and a remainder weight percent that includes a buffer material. The buffer material has a molecular structure defined by a first end, a second end, and a middle disposed between the first and second ends. The first end is a cyclic ring with nitrogen and oxygen heteroatomes, the middle is a hydrophobic alkyl chain, and the second end is a charged group.

  18. Mechanism of zinc electroplating in alkaline zincate solution

    Institute of Scientific and Technical Information of China (English)

    PENG Wen-jie; WANG Yun-yan

    2007-01-01

    The cathodic deposition properties and mechanism of Zn in alkaline zincate solution were studied by electrochemical techniques. The results show that Zn2+ exists in the alkaline solution in the form of Zn(OH)42-. The apparent activation energy of the electrode reaction is 38.93 kJ/mol, which indicates that the discharge of Zn(OH)42- on cathode is controlled by electrochemical polarization, and accompanied by a preceding chemical reaction. The diflusion coefficient of Zn(OH)42- is 2.452×10~cm2/s. Zn(OH)2 is the species directly discharged on the cathode surface. Based on the above results the mechanism of zinc electroplating in alkaline zincate solution was put forward.The discharged species is Zn(OH)2 formed from the preceding chemical reaction, which becomes Zn(OH)ad when gaining one electron, and then gaining the second electron to become Zn.The first electron gaining step is rate determining one.

  19. Interactions of N,N'-dimethylaminoethanol with steel surfaces in alkaline and chlorine containing solutions

    Science.gov (United States)

    Welle, A.; Liao, J. D.; Kaiser, K.; Grunze, M.; Mäder, U.; Blank, N.

    1997-10-01

    Formulations based on dilute aqueous solutions of N,N'-dimethylethanolamine (DMEA) are used to protect reinforcement steel bars ('rebar') in concrete from corrosion. In a previous paper we discussed the usefulness of X-ray photoelectron spectroscopy (XPS) to detect DMEA adsorbed from solution and the application of secondary neutral mass spectrometry (SNMS) to study migration of DMEA through a cement matrix. In this report we present XPS data of DMEA adsorbed on steel surfaces from alkaline and chlorine containing solutions of variable concentration range and discuss models for the interaction of DMEA with the oxidized steel surface and the mechanism of corrosion inhibition of DMEA. DMEA is strongly bonded to the steel surface and displaces ionic species from the substrate/solution interface hence protecting the ironoxide surface from ionic attack.

  20. OPTICAL PROPERTIES OF CARBAMIDE AQUEOUS SOLUTIONS

    Directory of Open Access Journals (Sweden)

    E. V. Avramenko

    2016-03-01

    Full Text Available Subject of Research. The paper presents the results of measurements of refractometric properties (refractive index n, its temperature factor dn/dt and the ultraviolet spectral absorption in carbonic acid diamide aqueous solutions (carbamide depending on solid residue mass fraction md = 0-50 % and on temperaturet = 10-70 °C.Method of Research. Laboratory methods ofliquid-phase medium refractometry and ultraviolet spectrophotometry were applied for the research. We carried out computational modeling of electronic states spectrum for the carbonic acid diamide molecule and theoretical calculation of the fundamental electronic absorption of the molecule in the ultraviolet wavelenght region.Main Results. We have established that the solution concentration md has a nonlinear character and may be represented by the quadratic polynomial with the error Δn= ± 0,0005. We have shown the refractive indexdependence on temperature n(t changes in linear fashion att = 10-70 °C.At that, the inclination of lines n(t increases at the increase of md; so, the temperature factor dn/dt may be approximated by the quadratic polynomial. Transmission spectra of solutions in the spectral region λ= 225-760 nm have no special features except for the sharp edge in the short-wavelength region; the fundamental electronic absorptionis responsible for it. We have established that dispersion dependences of the refraction index n(λ;md in aqueous solutions of carbamide at λ= 360-760 nm and at md = 0-50 % may be calculated with the satisfactory error without additional adjustable parameters from the ultraviolet absorption data in terms of the one-dimentional oscillator Lorentz model.PracticalRelevance. Representedmeasurements of carbonic acid diamide aqueous solutions optical properties may be applied for the adjustment and calibration of commercial refractometers at processing lines of the AdBlue reagent manufacture for the selective catalytic reduction (SCR of motor transport

  1. 21 CFR 524.1200b - Kanamycin ophthalmic aqueous solution.

    Science.gov (United States)

    2010-04-01

    ... § 524.1200b Kanamycin ophthalmic aqueous solution. (a) Specifications. The drug, which is in an aqueous solution including suitable and harmless preservatives and buffer substances, contains 10 milligrams of... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Kanamycin ophthalmic aqueous solution....

  2. Density of aqueous solutions of CO2

    Energy Technology Data Exchange (ETDEWEB)

    Garcia, Julio E.

    2001-10-10

    In this report, we present a numerical representation for the partial molar volume of CO2 in water and the calculation of the corresponding aqueous solution density. The motivation behind this work is related to the importance of having accurate representations for aqueous phase properties in the numerical simulation of carbon dioxide disposal into aquifers as well as in geothermal applications. According to reported experimental data the density of aqueous solutions of CO2 can be as much as 2-3% higher than pure water density. This density variation might produce an influence on the groundwater flow regime. For instance, in geologic sequestration of CO2, convective transport mixing might occur when, several years after injection of carbon dioxide has stopped, the CO2-rich gas phase is concentrated at the top of the formation, just below an overlaying caprock. In this particular case the heavier CO2 saturated water will flow downward and will be replaced by water with a lesser CO2 content.

  3. Electrochemical processing of alkaline nitrate and nitrite solutions

    International Nuclear Information System (INIS)

    Processing of high-level waste at the Savannah River Plant (SRP) will produce, as a by product, a low- level, alkaline salt solution containing approximately 17% sodium nitrate and sodium nitrite. This solution will be incorporated into a cement formulation, saltstone, and placed in an engineered landfill. Electrochemical methods have been investigated to decrease the nitrate and nitrite in this solution in order to lower the leaching of nitrate and nitrite from saltstone and to reduce the volume of saltstone. Laboratory experiments have demonstrated the technical feasibility of electrolytically reducing the nitrate and nitrite in a synthetic salt solution similar in composition to that expected to be produced at SRP. Greater than 99% of the sodium nitrate and sodium nitrite can be reduced, producing ammonia, nitrogen, oxygen, and sodium hydroxide. In addition, significant reductions in the volume of saltstone may be realized if the sodium hydroxide produced by electrolysis can be recycled

  4. Sorption of 137Cs from Aqueous Waste Solutions using Pottery

    International Nuclear Information System (INIS)

    A simple and inexpensive method for sorption of 137Cs from aqueous solutions using a highly available vase shape pottery material has been investigated. Porosity of the used pottery allowed for the penetration of the radioactive solution through its permeable body. Two routes had been investigated for cesium removal from the radioactive solutions. In the first one, pottery bodies were immersed into the radioactive solutions. In the second method; the radioactive solutions were filled the inner volumes of the pottery bodies. Vase shape pottery showed higher sorption capability for 137Cs much more than its powder forms, especially in the alkaline medium. Pottery bodies showed high potential for 137Cs removal. Adsorption isotherms revealed good lit to the Freundlich and Langumir isotherms. During sorption processes outside and inside the pottery body, 137Cs was well captured inside the amorphous microstructure of the pottery body. In this respect, micro filtration of cesium radionuclides through the used pottery could be postulated. Desorption experiments indicated higher immobilization affinity for radiocesium into pottery bodies, which indicates a high containment for 137Cs with an irreversible fixation mechanism

  5. NIR Spectroscopic Properties of Aqueous Acids Solutions

    Directory of Open Access Journals (Sweden)

    Mohd Zubir MatJafri

    2012-06-01

    Full Text Available Acid content is one of the important quality attributes in determining the maturity index of agricultural product, particularly fruits. Despite the fact that much research on the measurement of acidity in fruits through non-destructive spectroscopy analysis at NIR wavelengths between 700 to 1,000 nm has been conducted, the same response towards individual acids is not well known. This paper presents NIR spectroscopy analysis on aqueous citric, tartaric, malic and oxalic solutions through quantitative analysis by selecting a set of wavelengths that can best be used to measure the pH of the solutions. The aquaphotomics study of the acid solutions has generated R2 above 0.9 for the measurement of all acids. The most important wavelengths for pH are located at 918–925 nm and 990–996 nm, while at 975 nm for water.

  6. Optical manipulation of proteins in aqueous solution

    International Nuclear Information System (INIS)

    Optical trapping of lysozyme, cytochrome c, or myoglobin based on photon pressure generated by focusing 1064 nm laser beam in an aqueous solution was explored. For all the proteins, microparticle formation was observed at the focal point under an optical microscope. Furthermore, the microparticles were identified to the molecular assemblies of the corresponding protein by means of confocal Raman microspectroscopy. For lysozyme, molecular clusters in solution were optically trapped to form the microparticle and it took more than 1 h to produce the microparticle. By contrast, molecular assembling proceeded within 1 min for cytochrome c and myoglobin. Since heme in cytochrome c or myoglobin would have a high polarizability, that would contribute to rapid assembling of the protein. Thus we demonstrated that a focused laser beam was a powerful tool to manipulate protein molecules in solution.

  7. Aqueous Solution Vessel Thermal Model Development II

    Energy Technology Data Exchange (ETDEWEB)

    Buechler, Cynthia Eileen [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-10-28

    The work presented in this report is a continuation of the work described in the May 2015 report, “Aqueous Solution Vessel Thermal Model Development”. This computational fluid dynamics (CFD) model aims to predict the temperature and bubble volume fraction in an aqueous solution of uranium. These values affect the reactivity of the fissile solution, so it is important to be able to calculate them and determine their effects on the reaction. Part A of this report describes some of the parameter comparisons performed on the CFD model using Fluent. Part B describes the coupling of the Fluent model with a Monte-Carlo N-Particle (MCNP) neutron transport model. The fuel tank geometry is the same as it was in the May 2015 report, annular with a thickness-to-height ratio of 0.16. An accelerator-driven neutron source provides the excitation for the reaction, and internal and external water cooling channels remove the heat. The model used in this work incorporates the Eulerian multiphase model with lift, wall lubrication, turbulent dispersion and turbulence interaction. The buoyancy-driven flow is modeled using the Boussinesq approximation, and the flow turbulence is determined using the k-ω Shear-Stress-Transport (SST) model. The dispersed turbulence multiphase model is employed to capture the multiphase turbulence effects.

  8. Electrolytic denitrification of alkaline nitrate and nitrite solution

    International Nuclear Information System (INIS)

    Processing of high-level waste at the Savannah River Plant (SRP) will produce a low-level alkaline salt solution, containing approximately 17% sodium nitrate and sodium nitrite. This solution will be incorporated into a cement wasteform, saltstone, and placed in an engineered landfill. Laboratory experiments have demonstrated the technical feasibility of electrochemically reducing the nitrate and nitrite in a synthetic, nonradioactive salt solution similar in composition to that expected to be produced at SRP. Greater than ninety-five percent of the sodium nitrate and sodium nitrite can be reduced electrolytically, producing ammonia, nitrogen, oxygen, and sodium hydroxide. Reduction of the nitrate and nitrite will reduce the leaching of nitrate and nitrite from the saltstone monolith. In addition, significant reductions in the volume of saltstone may be realized if the sodium hydroxide produced by electrolysis can be recycled

  9. Pulse Radiolysis of Aqueous Thiocyanate Solution

    International Nuclear Information System (INIS)

    The pulse radiolysis of N2O saturated aqueous solutions of KSCN was studied under neutral pH conditions. The observed optical absorption spectrum of the SCN#lgbullet# radical in solution is more complex than previously reported, but it is in good agreement with that measured in the gas phase. Kinetic traces at 330 nm and 472 nm corresponding to SCN#lgbullet# and (SCN)2#lgbullet#-, respectively, were fit using a Monte Carlo simulation kinetic model. The rate coefficient for the oxidation of SCN- ions by OH radicals, an important reaction used in competition kinetics measurements, was found to be 1.4 ± 0.1 x 1010 M-1 s-1, about 30% higher than the normally accepted value. A detailed discussion of the reaction mechanism is presented

  10. Aqueous Solutions of Ionic Liquids: Microscopic Assembly.

    Science.gov (United States)

    Vicent-Luna, Jose Manuel; Dubbeldam, David; Gómez-Álvarez, Paula; Calero, Sofia

    2016-02-01

    Aqueous solutions of ionic liquids are of special interest, due to the distinctive properties of ionic liquids, in particular, their amphiphilic character. A better understanding of the structure-property relationships of such systems is hence desirable. One of the crucial molecular-level interactions that influences the macroscopic behavior is hydrogen bonding. In this work, we conduct molecular dynamics simulations to investigate the effects of ionic liquids on the hydrogen-bond network of water in dilute aqueous solutions of ionic liquids with various combinations of cations and anions. Calculations are performed for imidazolium-based cations with alkyl chains of different lengths and for a variety of anions, namely, [Br](-), [NO3](-), [SCN](-) [BF4](-), [PF6](-), and [Tf2N](-). The structure of water and the water-ionic liquid interactions involved in the formation of a heterogeneous network are analyzed by using radial distribution functions and hydrogen-bond statistics. To this end, we employ the geometric criterion of the hydrogen-bond definition and it is shown that the structure of water is sensitive to the amount of ionic liquid and to the anion type. In particular, [SCN](-) and [Tf2N](-) were found to be the most hydrophilic and hydrophobic anions, respectively. Conversely, the cation chain length did not influence the results.

  11. Study of the electrochemical oxidation mechanism of formaldehyde on gold electrode in alkaline solution

    Institute of Scientific and Technical Information of China (English)

    Rui-Wen Yan; Bao-Kang Jin

    2013-01-01

    The oxidation of formaldehyde in alkaline solution was studied by in situ rapid-scan time-resolved IR spectroelectrochemistry (RS-TR-FTIRS) method.In the potential range between-0.7 V and 0.2 V,the gem-diol anions were oxidized (according to the 2765 cm-1 ofvH-o and 1034 cm-1 ofvco downward IR bands) and the formate ions appeared (according to the 1588,1357 cm-1 of the asymmetric and symmetricvoco and 1380 cm-1 ofδc-H upward IR bands) in aqueous solution.It was also confirmed that gem-diol anion was oxidized (according to the 2026,1034 cm-1 downward IR bands) to formate ions (according to the 1595,1357,1380 cm-1 upward IR bands) and water (according to the 3427 cm-1 ofvH-o upward IR band) in heavy water solution.The results illustrated that formaldehyde formed gem-diol anion in alkaline solution and was absorbed on the electrode surface; then gem-diol anion was oxidized to formate ions and water.

  12. Aqueous solubility and alkaline hydrolysis of the novel high explosive hexanitrohexaazaisowurtzitane (CL-20).

    Science.gov (United States)

    Karakaya, Pelin; Sidhoum, Mohammed; Christodoulatos, Christos; Nicolich, Steve; Balas, Wendy

    2005-04-11

    The recently developed polycyclic nitramine CL-20 is considered as a possible replacement for the monocyclic nitramines RDX and HMX. The present study reports aqueous solubility data for CL-20, as well as the kinetic parameters for its alkaline hydrolysis with sodium hydroxide below and above its solubility limits. Aqueous solubility of CL-20 was measured in the temperature range of 4-69 degrees C and the data were fitted to a generalized solubility model. Alkaline hydrolysis experiments were conducted at 15, 20, 30 and 40 degrees C, with hydroxide concentrations ranging from 0.25 to 300 mM. Like RDX and HMX, alkaline hydrolysis of CL-20 follows second-order kinetics. CL-20 alkaline hydrolysis was found to proceed at a significantly faster rate than RDX. The temperature dependency of the second-order rate constants was evaluated using the Arrhenius model. The activation energy for CL-20 was found to be within close range of the activation energies reported for RDX and HMX. PMID:15811680

  13. The oxygen evolution reaction on passive oxide covered transition metal electrodes in alkaline solution. Part 2-Cobalt.

    OpenAIRE

    LYONS, MICHAEL EDWARD

    2008-01-01

    Details are outlined of an electrochemical investigation of the oxygen evolution reaction (OER) at passive oxide covered polycrystalline Co electrodes in aqueous alkaline solution. Kinetic studies on electrodes subjected to different pre-treatment routines, yielded different values of the Tafel slope and the reaction order with respect to OH- activity. Only one mechanistic pathway could account for all observed values of these kinetic parameters. This pathway is similar, although ...

  14. The oxygen evolution reaction on passive oxide covered transition metal electrodes in alkaline solution. Part III - Iron.

    OpenAIRE

    LYONS, MICHAEL EDWARD

    2008-01-01

    The kinetics of the oxygen evolution reaction (OER) at passive oxide covered polycrystalline Fe electrodes in aqueous alkaline solution were examined using both dc steady state polarisation and ac impedance techniques. It proved difficult to obtain reproducible polarisation data for bright anodes, and so an electrochemical pre-treatment routine was devised. Upon ageing of a given electrode specimen, and with application of the pre-treatment regime before each experiment, it was po...

  15. Apparent Dissolution Kinetics of Diatomite in Alkaline Solution

    Institute of Scientific and Technical Information of China (English)

    DU Gaoxiang; L(U) Guocheng; HE Xuwen

    2013-01-01

    The dissolution kinetics of diatomite in alkaline solution is the theoretical basis for the process optimization of alkali-diatomite reaction and its applications.In this study,the dissolution kinetics of diatomite in NaOH solution is investigated.The results indicate that the dissolution reaction fits well the unreacted shrinking core model for solid-liquid heterogeneous reactions.The apparent reaction order for NaOH is 2 and the apparent activation energy for the reaction (Ea) is 28.06 kJ.mol-1.The intra-particle diffusion through the sodium silicate layer is the rate-controlling step.When the dissolution reaction occurs at the interface of unreacted diatomite solid core,the diffusion in the trans-layer (the liquid film around the wetted particle) reduces the rate of whole dissolution process.

  16. Corrosion of silicon nitride in high temperature alkaline solutions

    Science.gov (United States)

    Qiu, Liyan; Guzonas, Dave A.; Qian, Jing

    2016-08-01

    The corrosion of silicon nitride (Si3N4) in alkaline solutions was studied at temperatures from 60 to 300 °C. Si3N4 experienced significant corrosion above 100 °C. The release rates of silicon and nitrogen follow zero order reaction kinetics and increase with increasing temperature. The molar ratio of dissolved silicon and nitrogen species in the high temperature solutions is the same as that in the solid phase (congruent dissolution). The activation energy for silicon and nitrogen release rates is 75 kJ/mol which agrees well with that of silica dissolution. At 300 °C, the release of aluminum is observed and follows first order reaction kinetics while other minor constituents including Ti and Y are highly enriched on the corrosion films due to the low solubility of their oxides.

  17. Catalyzed reduction of nitrate in aqueous solutions

    International Nuclear Information System (INIS)

    Sodium nitrate and other nitrate salts in wastes is a major source of difficulty for permanent disposal. Reduction of nitrate using aluminum metal has been demonstrated, but NH3, hydrazine, or organic compounds containing oxygen would be advantageous for reduction of nitrate in sodium nitrate solutions. Objective of this seed money study was to determine minimum conditions for reduction. Proposed procedure was batchwise heating of aqueous solutions in closed vessels with monitoring of temperatures and pressures. A simple, convenient apparatus and procedure were demonstrated for observing formation of gaseous products and collecting samples for analyses. The test conditions were 250 degree C and 1000 psi max. Any useful reduction of sodium nitrate to sodium hydroxide as the primary product was not found. The nitrate present at pHs 3 or NH4NO3 is easily decomposed, and the effect of nitromethane at these low pHs was confirmed. When acetic acid or formic acid was added, 21 to 56% of the nitrate in sodium nitrate solutions was reduced by methanol or formaldehyde. With hydrazine and acetic acid, 73 % of the nitrate was decomposed to convert NaNO3 to sodium acetate. With hydrazine and formic acid, 36% of the nitrate was decomposed. If these products are more acceptable for final disposal than sodium nitrate, the reagents are cheap and the conversion conditions would be practical for easy use. Ammonium acetate or formate salts did not significantly reduce nitrate in sodium nitrate solutions

  18. On the complex structural diffusion of proton holes in nanoconfined alkaline solutions within slit pores.

    Science.gov (United States)

    Muñoz-Santiburcio, Daniel; Marx, Dominik

    2016-01-01

    The hydroxide anion OH(-)(aq) in homogeneous bulk water, that is, the solvated proton hole, is known to feature peculiar properties compared with excess protons solvated therein. In this work, it is disclosed that nanoconfinement of such alkaline aqueous solutions strongly affects the key structural and dynamical properties of OH(-)(aq) compared with the bulk limit. The combined effect of the preferred hypercoordinated solvation pattern of OH(-)(aq), its preferred perpendicular orientation relative to the confining surfaces, the pronounced layering of nanoconfined water and the topology of the hydrogen bond network required for proton hole transfer lead to major changes of the charge transport mechanism, in such a way that the proton hole migration mechanism depends exquisitely on the width of the confined space that hosts the water film. Moreover, the anionic Zundel complex, which is of transient nature in homogeneous bulk solutions, can be dynamically trapped as a shallow intermediate species by suitable nanoconfinement conditions. PMID:27550616

  19. On the complex structural diffusion of proton holes in nanoconfined alkaline solutions within slit pores

    Science.gov (United States)

    Muñoz-Santiburcio, Daniel; Marx, Dominik

    2016-08-01

    The hydroxide anion OH-(aq) in homogeneous bulk water, that is, the solvated proton hole, is known to feature peculiar properties compared with excess protons solvated therein. In this work, it is disclosed that nanoconfinement of such alkaline aqueous solutions strongly affects the key structural and dynamical properties of OH-(aq) compared with the bulk limit. The combined effect of the preferred hypercoordinated solvation pattern of OH-(aq), its preferred perpendicular orientation relative to the confining surfaces, the pronounced layering of nanoconfined water and the topology of the hydrogen bond network required for proton hole transfer lead to major changes of the charge transport mechanism, in such a way that the proton hole migration mechanism depends exquisitely on the width of the confined space that hosts the water film. Moreover, the anionic Zundel complex, which is of transient nature in homogeneous bulk solutions, can be dynamically trapped as a shallow intermediate species by suitable nanoconfinement conditions.

  20. Absorption and Chemisorption of Small Levitated Single Bubbles in Aqueous Solutions

    OpenAIRE

    Alexander Tollkötter; Norbert Kockmann

    2014-01-01

    The absorption and chemisorption of small bubbles with N2 or CO2 were investigated experimentally in aqueous and alkaline solutions. Different bubble sizes were studied ranging from 0.1 to 2.5 mm in alkaline concentrations of 0.1 mM to 1 M NaOH. The experiments were conducted in a device consisting of a converging microchannel with a down flowing liquid. Levitation positions of single bubbles were optically characterized. A correlation was developed for the drag force coefficient, CD, includi...

  1. 臭氧氧化结合碱液吸收法烟气脱硝的工艺研究%Absorption of NOx from flue gas with alkaline aqueous solution combined with gas-phase oxidation of NO using ozone

    Institute of Scientific and Technical Information of China (English)

    李君; 盛重义; 杨柳; 邓劲松

    2014-01-01

    NO was oxidized into NO2 first by injecting ozone into flue gas stream,and then NO2 was absorbed from flue gas by urea,sodium hydroxide and calcium hydroxide solution. The mole ratio of O3 to NO,inlet NO and SO2 concentration in flue gas,and relative humidity were investigated in the influence of NO oxidation. The experimental results indicated that the optimal molar ratio of O3 to NO is 1. 02. NO conversion decreased with the increase of NO concentration. The SO2 concentration and the relative humidity in flue gas have few effects on the NO oxidation. The absorption products of NOx oxidized by ozone injection with NaOH aqueous solution were analyzed. And the characterization results showed that NO was little absorbed by alkaline aqueous solution, while the NO2 absorption efficiency was more than 80%.%利用臭氧将烟气中溶解度较小的NO氧化成NO2,再结合尿素、氢氧化钠、氢氧化钙溶液吸收脱除臭氧氧化产物,重点考察了O3与NO反应的摩尔比、进口NO浓度、烟气中SO2浓度和相对湿度等工艺参数对NO氧化的影响,并探明不同的吸收液脱除臭氧氧化产物的特性。结果显示O3与NO反应的最佳摩尔比为1.02,随着进口NO浓度的增加氧化效率下降,而烟气中的SO2和相对湿度对NO氧化影响较小。通过对氢氧化钙吸收臭氧氧化产物的特性分析得出,碱液对NO的吸收率相对较小,而对NO2的吸收率达到80%以上。

  2. Functionalized polymers for binding to solutes in aqueous solutions

    Science.gov (United States)

    Smith, Barbara F.; Robison, Thomas W.

    2006-11-21

    A functionalized polymer for binding a dissolved molecule in an aqueous solution is presented. The polymer has a backbone polymer to which one or more functional groups are covalently linked. The backbone polymer can be such polymers as polyethylenimine, polyvinylamine, polyallylamine, and polypropylamine. These polymers are generally water-soluble, but can be insoluble when cross-linked. The functional group can be for example diol derivatives, polyol derivatives, thiol and dithiol derivatives, guest-host groups, affinity groups, beta-diphosphonic acids, and beta-diamides

  3. Removal of radium from aqueous solutions using adsorbent produced from coconut coir pith

    International Nuclear Information System (INIS)

    A study was conducted to evaluate the potential use of the coconut coir pith as an adsorbent for the removal of radium from aqueous solutions. Experiments to establish adsorptions as a function of pH and contact time were carried out. The results showed that radium adsorption are dependent upon pH and contact time of coconut coir pith with aqueous solutions. 70-80% of radium were adsorbed in the neutral to alkaline pH range. The amount of radium adsorbed also increased with contact time, reaching an optimum after 250 min. Thus, it can be concluded that the coconut coir pith has the potential to be used as an adsorbent in radium removal from aqueous solutions. (Author)

  4. Zinc electrodeposition from alkaline zincate solution by pulsating overpotentials

    Directory of Open Access Journals (Sweden)

    MILOS V. SIMICIC

    2000-09-01

    Full Text Available It is well known that smooth zinc deposits cannot be obtained from alkaline zincate using constant overpotential and current rate. During prolonged metal deposition, spongy and dendritic deposits are formed. It has been shown that the deposits are less agglomerated in the case of square-wave pulsating overpotentials regime than the ones obtained in case of constant overpotential regime. This is explained in a semiquantitative way by two phenomena: selective anodic dissolution during overpotentials “off” period and decreasing diffusion control. These effects is more pronounced at higher pause-to-pulse ratio. Increasing the pause-to-pulse ratio causes a reduction of the ratio between diffusion and activation overpotential, resulting in a more compact deposit. Confirmation of the proposed semiquantitative mathematical model was obtained by zinc electrodeposition onto a copper wire from a 0.1 M zincate solution in 1.0 M KOH at room temperature.

  5. Electrochemical kinetics of gold dissolving in alkaline thiourea solution

    Institute of Scientific and Technical Information of China (English)

    CHAI Li-yuan; WANG Yun-yan

    2006-01-01

    Kinetic parameters of the electrode reactions were measured by investigating steady-state current-potential behaviors. The results show that the apparent transfer coefficient of anodic process is 0.058 2, diffusion coefficient of thiourea gold complex is 6.04 × 10-6 cm2/s,anodic reaction order of thiourea is 2. 018 3, and anodic reaction order of OH- is 0. 016 6. The theoretical kinetics equation of gold dissolving in alkaline thiourea solution is deduced,which indicates that anodic reaction order of thiourea is 2, and anodic reaction order of OH- is 0. The theoretical values of the kinetic parameters are consistent with experimental values very well. The correctness of the mechanism is further demonstrated using apparent transfer coefficient according to the electrochemical dynamic equation of multi-electron reaction.

  6. Humic acid removal from aqueous solutions by peroxielectrocoagulation process

    Directory of Open Access Journals (Sweden)

    Ahmad Reza Yazdanbakhsh

    2015-06-01

    Full Text Available Background: Natural organic matter is the cause of many problems associated with water treatment such as the presence of disinfection by-products (DBPs and membrane fouling during water filtration. In this study, the performance of the peroxi-electrocoagulation process (PEP was investigated for the removal of humic acids (HAs from aqueous solutions. Methods: PEP was carried out for the removal of HA using a plexiglas reactor with a volume of 2 L and fitted with iron electrodes and a direct current supply (DC. Samples were taken at various amounts of pH (2-4, current density (1 and 2A/cm2, hydrogen peroxide (50-150 mg/L and reaction time (5-20 minutes and then filtered to remove sludge formed during reaction. Finally, the HA concentration was measured by UV absorbance at 254 nm (UV254. Results: Results indicated that increasing the concentration of H2O2 from 50 to 150 mg/L increased HA removal efficiency from 83% to 94.5%. The highest removal efficiency was observed at pH 3.0; by increasing the pH to the alkaline range, the efficiency of the process was reduced. It was found that HA removal efficiency was high in current density 1A/cm2. Increasing current density up to 1 A cm-2 caused a decrease in removal efficiency. Results of this study showed that under the optimum operating range for the process ([current density] = 1A/cm2, [hydrogen peroxide concentration] = 150 mg/L, [reaction time]= 20 minutes and [pH]= 3.0, HA removal efficiency reached 98%. Conclusion: It can be concluded that PEP has the potential to be utilized for cost-effective removal of HA from aqueous solutions.

  7. Pulse radiolysis of tetraalkylammonium hydroxides in alkaline solution containing oxygen

    International Nuclear Information System (INIS)

    In the pulse radiolysis of aqueous oxygenated solutions of tetraalkylammonium hydroxides there is a build-up of ozonide ion lasting up to 100 μs after the pulse. The build-up does not occur in solutions containing a twenty fold (reactivity) excess of N2O to O2. The influence of various concentrations of tetraalkylammonium cations, oxygen and different reactivity ratios of N2O to O2 on the build-up of ozonide ion after the pulse was investigated. The reaction rates of O2-and O- with peroxy radicals and organic cations, respectively, control the nature of the observed build-up and decay of ozonide ion. (author)

  8. Raman spectroscopy application to analyses of components in aqueous solutions

    Science.gov (United States)

    Li, Gang; Zhang, Guoping

    2006-09-01

    The characterization of species in aqueous solutions has presented a challenge to analytical and physical chemist, because the JR absorption of the aqueous solvent is so intense that it becomes difficult to observe the solute in the water by JR absorption. In contrast, Raman spectrum of the solute is unaffected by the water, so the weak scattering of water makes the technique well suited to aqueous samples, and the Raman spectrum exhibits well-defined bands corresponding to fundamental modes of vibration. In addition, Raman spectroscopy has some inherent advantages in aqueous solution analysis, because the spectral features of signals from different species are much more distinct, and it provides characteristic signatures for samples, such as blood, protein and cholesterol. All the advantages make Raman spectroscopy be a potential alternative for the study of aqueous solutions. Now, Raman spectroscopy has been applied to studying samples in aqueous solutions, blood serum, intracellular protein levels. Now, industrial wasted water contains many organic contaminants, and it is necessary to determine and monitor these contaminants. The paper first introduces Raman spectroscopy, and then describes its applications to determining the components in aqueous solutions, analyzes and assignes the Raman spectra of o-dichlorobenzene, o-xylene, m-xyiene and p-xylene in detail. The experimental results demonstrate that Raman spectroscopy is a particularly powerful technique for aqueous solutions analyses.

  9. Acetic acid extraction from aqueous solutions using fatty acids

    NARCIS (Netherlands)

    IJmker, H.M.; Gramblicka, M.; Kersten, S.R.A.; Ham, van der A.G.J.; Schuur, B.

    2014-01-01

    A major challenge for production of acetic acid via bio-based routes is cost-effective concentration and purification of the acetic acid from the aqueous solutions, for which liquid–liquid extraction is a possible method. A main challenge in extraction of acetic acid from dilute aqueous solutions is

  10. ESR study on carboxymethyl chitosan radicals in an aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Saiki, Seiichi, E-mail: saiki.seiichi@jaea.go.j [Graduate School of Engineering, University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-8656 (Japan); Quantum Beam Science Directorate, Japan Atomic Energy Agency, 1233 Watanuki, Takasaki, Gunma 370-1292 (Japan); Nagasawa, Naotsugu; Hiroki, Akihiro; Morishita, Norio; Tamada, Masao [Quantum Beam Science Directorate, Japan Atomic Energy Agency, 1233 Watanuki, Takasaki, Gunma 370-1292 (Japan); Muroya, Yusa; Kudo, Hisaaki [Graduate School of Engineering, University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-8656 (Japan); Katsumura, Yosuke [Graduate School of Engineering, The University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-8656 (Japan); Advanced Science Research Center, Japan Atomic Energy Agency, 2-4 Shirakata-Shirane, Tokai, Naka, Ibaraki 319-1195 (Japan)

    2010-03-15

    Carboxymethyl chitosan (CMCTS) at a highly concentrated aqueous solution forms hydrogel by ionizing irradiation. To study on radiation-induced reaction mechanism of CMCTS in an aqueous solution, CMCTS radicals formed by reactions with OH radical were observed by ESR method. As a result of ESR spectral analysis, CMCTS radicals were identified as radicals on carboxymethyl groups.

  11. Structure of aqueous sodium perchlorate solutions.

    Science.gov (United States)

    General, Ignacio J; Asciutto, Eliana K; Madura, Jeffry D

    2008-12-01

    Salt solutions have been the object of study of many scientists through history, but one of the most important findings came along when the Hofmeister series were discovered. Their importance arises from the fact that they influence the relative solubility of proteins, and solubility is directly related to one of today's holy grails: protein folding. In this work we characterize one of the more-destabilizing salts in the series, sodium perchlorate, by studying it as an aqueous solution at various concentrations ranging from 0.08 to 1.60 mol/L. Molecular dynamics simulations at room temperature permitted a detailed study of the organization of solvent and cosolvent, in terms of its radial distribution functions, along with the study of the structure of hydrogen bonds in the ions' solvation shells. We found that the distribution functions have some variations in their shape as concentration changes, but the position of their peaks is mostly unaffected. Regarding water, the most salient fact is the noticeable (although small) change in the second hydration shell and even beyond, especially for g(O(w)***O(w)), showing that the locality of salt effects should not be restricted to considerations of only the first solvation shell. The perturbation of the second shell also appears in the study of the HB network, where the difference between the number of HBs around a water molecule and around the Na(+) cation gets much smaller as one goes from the first to the second solvation shell, yet the difference is not negligible. Nevertheless, the effect of the ions past their first hydration shell is not enough to make a noticeable change in the global HB network. The Kirkwood-Buff theory of liquids was applied to our system, in order to calculate the activity derivative of the cosolvent. This coefficient, along with a previously calculated preferential binding, allowed us to establish that if a folded AP peptide is immersed in the studied solution, becoming the solute, then

  12. Direct Solar Charging of an Organic-Inorganic, Stable, and Aqueous Alkaline Redox Flow Battery with a Hematite Photoanode.

    Science.gov (United States)

    Wedege, Kristina; Azevedo, João; Khataee, Amirreza; Bentien, Anders; Mendes, Adélio

    2016-06-13

    The intermittent nature of the sunlight and its increasing contribution to electricity generation is fostering the energy storage research. Direct solar charging of an auspicious type of redox flow battery could make solar energy directly and efficiently dispatchable. The first solar aqueous alkaline redox flow battery using low cost and environmentally safe materials is demonstrated. The electrolytes consist of the redox couples ferrocyanide and anthraquinone-2,7-disulphonate in sodium hydroxide solution, yielding a standard cell potential of 0.74 V. Photovoltage enhancement strategies are demonstrated for the ferrocyanide-hematite junction by employing an annealing treatment and growing a layer of a conductive polyaniline polymer on the electrode surface, which decreases electron-hole recombination. PMID:27151516

  13. Removal of radium from aqueous solutions

    International Nuclear Information System (INIS)

    Adsorption of radium from aqueous solution with montmorillonite clay was investigated. Adsorption isotherm data of the radium and montmorillonite clay system were developed and fitted to both the Langmuir and Freundlich isotherm equations. The Langmuir isotherm equation was determined to be q = 6.700 C/1 + 8.447 x 10-5C and the Freundlich isotherm equation is q = 45.431 C/sup 1/1.401/. A rotary precoat filtration technique was used for dewatering the slurries of the montmorillonite clay and diatomaceous earth mixture. The rate of filtration was found to be a function of the weight percent of the clay, applied vacuum, drum speed and precoat thickness. The functional relationship is of the form Q = (0.682 + 0.035 X1 - 0.014 X2 + 0.140 X3 + 0.007 X1X2)/1 + (3.744 - 0.767 X3 + 0.079 X1X2)C125. 15 figures, 11 tables

  14. New sand consolidation technique using hot alkaline solutions: laboratory evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Moreno, F.E.; Rico, A.; Mendez, Z. [PDVSA-Intevep, Caracas (Venezuela); Materan, S. [Simon Bolivar Univ., Caracas (Venezuela)

    2002-06-01

    Some well known problems in the petroleum industry are related to sanding problems caused by pressure falls, friction and dissolution of minerals during steam injection. The prospect of using hot alkaline solutions to achieve sand consolidation was investigated in this paper. Experimental work was performed using Venezuelan sand samples (S-1, S-2, and S-3) from various unconsolidated heavy oil reservoirs and commercial Silboca (S-4) sands to validate this new reservoir sand consolidation technique. A pressure of 500 pounds per square inch was applied to samples that had been packed into Teflon tubes and placed in a horizontal stainless steel cell. Following this, for a period varying from 2 to 5 hours, a hot sodium carbonate solution between 120 and 250 Celsius was injected. Every twenty minutes, the effluent solution was sampled. Before and after each run, permeability measurements were obtained to monitor the variations. Sand packs were dried at 100 Celsius after each test. An electron microscope was used to observe the morphology of secondary phases. For S-1 and S-2, sodium aluminium silicates were identified in the secondary phases for tests with temperature above 240 Celsius. In the case of S-3 and S-4, no consolidation was observed. The authors believe that large grain sizes and a 98 per cent quartz content respectively explain this phenomenon. It is suspected that sand consolidation requires the presence of aluminium contained in clays and/or feldspar. The critical parameters for sand consolidation were identified as temperature, pore volume, composition, and grain size. The process did not seem greatly affected by soaking time and injection rate. The advantages of this technique would be principally the minimization of sanding problems and reductions in the costs associated with production operations. 7 refs., 12 figs.

  15. Ozone photolysis of paracetamol in aqueous solution.

    Science.gov (United States)

    Neamţu, Mariana; Bobu, Maria; Kettrup, Antonius; Siminiceanu, Ilie

    2013-01-01

    The degradation of a paracetamol (N-acetil-para-aminofenol) aqueous solution (C (0) P = 5 mmol L(-1)) is studied in a bench-scale setup by means of simple ozonation (O3) and ozonation catalyzed with UV light (O3/UV) in order to quantify the influence of UV light on the degradation process. The results have shown that under the adopted experimental conditions (25°C, applied ozone dose = 9.8 mg L(-1) and gas flow rate of 20 L h(-1)) both oxidative systems are capable of removing the substrate with mineralization degrees up to 51% for ozonation and 53% for O3/UV. HPICE chromatography allowed the detection of nitrate ions and maleic and oxalic acids as ultimate carboxylic acids. The experimental data have been interpreted through 5 indicators: the conversion of paracetamol (XP ), the conversion degree of TOC (XTOC ), the apparent rate constant (kap ), the Hatta number (Ha) and the enhancement factor (E). The main advantage of photo-ozonation compared to simple ozonation was a more advanced conversion (79% vs. 92% after 90 min). The paracetamol decay follows a pseudo-first-order reaction with a superior rate constant (higher by 54%) for the UV catalyzed system in comparison with direct ozonation. Mineralization is slightly accelerated (+4%) in the O3/UV system, due to the additional production of hydroxyl radicals induced by the UV light and a higher Hatta number (+24%). Nevertheless, the process was still in the slow reaction kinetic regime (Ha < 0.3), and the enhancement factor was not significantly increased. The results are useful for the design and scale-up of the gas-liquid processes. PMID:23647117

  16. Ozone photolysis of paracetamol in aqueous solution.

    Science.gov (United States)

    Neamţu, Mariana; Bobu, Maria; Kettrup, Antonius; Siminiceanu, Ilie

    2013-01-01

    The degradation of a paracetamol (N-acetil-para-aminofenol) aqueous solution (C (0) P = 5 mmol L(-1)) is studied in a bench-scale setup by means of simple ozonation (O3) and ozonation catalyzed with UV light (O3/UV) in order to quantify the influence of UV light on the degradation process. The results have shown that under the adopted experimental conditions (25°C, applied ozone dose = 9.8 mg L(-1) and gas flow rate of 20 L h(-1)) both oxidative systems are capable of removing the substrate with mineralization degrees up to 51% for ozonation and 53% for O3/UV. HPICE chromatography allowed the detection of nitrate ions and maleic and oxalic acids as ultimate carboxylic acids. The experimental data have been interpreted through 5 indicators: the conversion of paracetamol (XP ), the conversion degree of TOC (XTOC ), the apparent rate constant (kap ), the Hatta number (Ha) and the enhancement factor (E). The main advantage of photo-ozonation compared to simple ozonation was a more advanced conversion (79% vs. 92% after 90 min). The paracetamol decay follows a pseudo-first-order reaction with a superior rate constant (higher by 54%) for the UV catalyzed system in comparison with direct ozonation. Mineralization is slightly accelerated (+4%) in the O3/UV system, due to the additional production of hydroxyl radicals induced by the UV light and a higher Hatta number (+24%). Nevertheless, the process was still in the slow reaction kinetic regime (Ha < 0.3), and the enhancement factor was not significantly increased. The results are useful for the design and scale-up of the gas-liquid processes.

  17. Stability in alkaline aqueous electrolyte of air electrode protected with fluorinated interpenetrating polymer network membrane

    Science.gov (United States)

    Bertolotti, Bruno; Messaoudi, Houssam; Chikh, Linda; Vancaeyzeele, Cédric; Alfonsi, Séverine; Fichet, Odile

    2015-01-01

    We developed original anion exchange membranes to protect air electrodes operating in aqueous lithium-air battery configuration, i.e. supplied with atmospheric air and in concentrated aqueous lithium hydroxide. These protective membranes have an interpenetrating polymer network (IPN) architecture combining a hydrogenated cationic polyelectrolyte network based on poly(epichlorohydrin) (PECH) and a fluorinated neutral network based on perfluoropolyether (Fluorolink® MD700). Two phases, each one rich in one of the polymer, are co-continuous in the materials. This morphology allows combining their properties according to the weight proportions of each polymer. Thus, PECH/Fluorolink IPNs show ionic conductivity varying from 1 to 2 mS cm-1, water uptake from 30 to 90 wt.% and anionic transport number from 0.65 to 0.80 when the PECH proportion varies from 40 to 90 wt.%. These membranes have been systematically assembled on air electrodes. Air electrode protected with PECH/Fluorolink 70/30 IPN shows outstanding stability higher than 1000 h, i.e. a 20-fold increase in the lifetime of the non-modified electrode. This efficient membrane/air electrode assembly is promising for development of alkaline electrolyte based storage or production energy systems, such as metal air batteries or alkaline fuel cells.

  18. Reaction mechanism of 3-chlorophenol with OH, H in aqueous solution.

    Science.gov (United States)

    Zhu, Jie; Chen, Ye-Fei; Dong, Wen-Bo; Pan, Xun-Xi; Hou, Hui-Qi

    2003-01-01

    The reaction mechanism of 3-chlorophenol with OH, H in aqueous solution was studied by transient technology. The 3-chlorophenol aqueous solutions have been saturated with air or N2 previously. Under alkaline condition, the reaction of OH radical with 3-chlorophenol produces 3-chlorinated phenoxyl radical, with the absorption peaks at 400 nm and 417 nm. Under neutral condition, the reaction of OH radical with 3-chlorophenol produces OH-adduct with the maximal absorption at about 340 nm. And in acid solution, the reaction of H with 3-chlorophenol produces H-adduct with the maximal absorption at about 320 nm. 3-chlorophenol is compared with 4-and 2-chlorophenols from the free radical pathways. The results show that the positions of chlorine on the aromatic ring strongly influence the dehalogenation and degradation process.

  19. Mechanism of formation of oil by the hot aqueous alkaline digestion of cellulose

    Energy Technology Data Exchange (ETDEWEB)

    Molten, P.M.; Miller, R.K.; Donovan, J.M.; Demmitt, T.F.

    1977-01-01

    The overall mechanism of cellulose converson in hot aqueous alkali appears to be one of degradation through glucose to low molecular weight saccharinic acids, dihydroxybutyric acid, glycolic acid, and carbonyl products such as acetone, acetaldehyde, formaldehyde, and similar compounds. Although the products identified in the present report were fairly complex furans, carbocyclic ketones, unsaturated hydrocarbons, and aromatic compounds, nevertheless, in most cases, they could have been formed from simple carbonyl compounds through a series of condensations involving carbanion intermediates. It is conceivable that residual alkali in the oil during acetone extraction could have given rise to diacetone alcohol as an artifact. This is refuted by examination of an aqueous residue which was extracted with diethyl ether and which was never exposed to any acetone: Compounds derived from diacetone alcohol (such as mesityl oxide or 4-methyl-3-penten-2-one) were also identified in the diethyl ether extract of the aqueous phase. Other compounds were identified in the oil acetone extract which could not have been derived from acetone or diacetone alcohol, but which could have been formed from other carbonyl compounds by the same mechanism. Hence, diacetone alcohol is a genuine product of cellulose conversion although apparently not an intermediate in further synthesis of other products. The further reaction of the postulated cyclic intermediates, and the route to formation of unsaturated hydrocarbons of high molecular weight is intended to be the next subject of investigation in the current work. The fundamental difference in the mechanism of cellulose conversion to oil by pyrolysis and by aqueous alkaline digestion predicted by theory is therefore confirmed. Pyrolysis products may be explained generally by carbonium ion and free radical reactions (in fact, cellulose decomposition is acid-catalyzed), while in aqueous alkali, nucleophilic carbanion reactions are favored.

  20. Reactive transport modeling of column experiments on the evolution of saline-alkaline waste solutions.

    Science.gov (United States)

    Zheng, Zuoping; Zhang, Guoxiang; Wan, Jiamin

    2008-04-01

    Leakage of saline-alkaline tank waste solutions often creates a serious environmental contamination problem. To better understand the mechanisms controlling the fate of such waste solutions in the Hanford vadose zone, we simulated reactive transport in columns designed to represent local site conditions. The Pitzer ion interaction module was used, with principal geochemical processes considered in the simulation including quartz dissolution, precipitation of brucite, calcite, and portlandite, multi-component cation exchange, and aqueous complexation reactions. Good matches were observed between the simulated and measured column data at ambient temperature ( approximately 21 degrees C). Relatively good agreement was also obtained at high temperature ( approximately 70 degrees C). The decrease of pH at the plume front is examined through formation of secondary mineral phases and/or quartz dissolution. Substantial formation of secondary mineral phases resulting from multi-component cation exchange suggests that these phases are responsible for a decrease in pH within the plume front. In addition, a sensitivity analysis was conducted with respect to cation exchange capacity, selectivity coefficient, mineral assemblage, temperature, and ionic strength. This study could serve as a useful guide to subsequent experimental work, to thermodynamic models developed for the concentrated solutions at high ionic strength and to other types of waste plume studies. PMID:18313795

  1. Reactive transport modeling of column experiments on the evolution of saline alkaline waste solutions

    Science.gov (United States)

    Zheng, Zuoping; Zhang, Guoxiang; Wan, Jiamin

    2008-04-01

    Leakage of saline-alkaline tank waste solutions often creates a serious environmental contamination problem. To better understand the mechanisms controlling the fate of such waste solutions in the Hanford vadose zone, we simulated reactive transport in columns designed to represent local site conditions. The Pitzer ion interaction module was used, with principal geochemical processes considered in the simulation including quartz dissolution, precipitation of brucite, calcite, and portlandite, multi-component cation exchange, and aqueous complexation reactions. Good matches were observed between the simulated and measured column data at ambient temperature (˜ 21 °C). Relatively good agreement was also obtained at high temperature (˜ 70 °C). The decrease of pH at the plume front is examined through formation of secondary mineral phases and/or quartz dissolution. Substantial formation of secondary mineral phases resulting from multi-component cation exchange suggests that these phases are responsible for a decrease in pH within the plume front. In addition, a sensitivity analysis was conducted with respect to cation exchange capacity, selectivity coefficient, mineral assemblage, temperature, and ionic strength. This study could serve as a useful guide to subsequent experimental work, to thermodynamic models developed for the concentrated solutions at high ionic strength and to other types of waste plume studies.

  2. Nanoscale lubricating film formation by linear polymer in aqueous solution

    Science.gov (United States)

    Liu, Shuhai; Guo, Dan; Xie, Guoxin

    2012-11-01

    Film-forming properties of polymer in aqueous solution flowing through a nanogap have been investigated by using a thin film interferometry. The film properties of linear polymer in aqueous solution flowing through a confined nanogap depend on the ratio of water film thickness to averaged radius of polymer chains H0/RPolymer. It was found that the lubrication film thickness of linear polymer in aqueous solution decreases as the polymer molecular weight increasing when H0/RPolymer < 2 ˜ 3. A new lubrication map was proposed, which includes the lubrication regime of weak confinement influence, the lubrication regime of strong confinement influence (LRSCI), and the transition regime of confinement influence. It is very difficult to increase the lubrication film thickness using the higher molecule weight in the LRSCI regime. The lubrication mechanism inferred from our experimental results may help to better understand the dynamic film properties of linear polymer in aqueous solution flowing through a nanogap.

  3. Surface tension and related thermodynamic quantities of aqueous electrolyte solutions

    CERN Document Server

    Matubayasi, Norihiro

    2013-01-01

    Surface tension provides a thermodynamic avenue for analyzing systems in equilibrium and formulating phenomenological explanations for the behavior of constituent molecules in the surface region. While there are extensive experimental observations and established ideas regarding desorption of ions from the surfaces of aqueous salt solutions, a more successful discussion of the theory has recently emerged, which allows the quantitative calculation of the distribution of ions in the surface region. Surface Tension and Related Thermodynamic Quantities of Aqueous Electrolyte Solutions provides a d

  4. Fabrication of ZnO:Mn nanoparticles with organic shell in a highly alkaline aqueous environment

    Science.gov (United States)

    Chawla, Santa; Sharda; Jayanthi, K.

    2011-01-01

    Synthesis of undoped and Mn doped ZnO nanoparticles by an inclusive co precipitation method and in situ capping with heteromultifunctional organic stabilizer mercaptosuccinic acid (MSA) in a core shell structure, in highly alkaline aqueous matrix have been accomplished. Near room temperature synthesis resulted in high quality monophasic wurtzite hexagonal structure of rod shaped nanoparticles of bare ZnO:Mn with no signature of dopant as separate phase. MSA capping resulted in nanoball like formation. Thermo gravimetric analysis (TGA) and FTIR confirmed MSA capping. ZnO: Mn particles emit in orange and red when excited by UV and blue light. Surface modification makes the nanoparticles hydrophilic with active organic surface easy for bioconjugation with any ligand and can have applications in drug delivery or as nanoscale fluorescent probe in a biological system.

  5. Spectroscopic and mechanistic investigations into oxidation of aspartame by diperiodatocuprate(III in aqueous alkaline medium

    Directory of Open Access Journals (Sweden)

    Jayant I. Gowda

    2015-12-01

    Full Text Available The oxidation of aspartame (ASP by diperiodatocuprate(III (DPC in aqueous alkaline medium at 298 K and a constant ionic strength of 0.30 mol dm−3 was studied spectrophotometrically. The reaction between aspartame and diperiodatocuprate(III in alkaline medium exhibits 1:6 stoichiometry in the reaction. The order of the reaction with respect to [diperiodatocuprate(III] was unity, while the apparent order with respect to [aspartame] was less than unity over the concentration range studied. The rate of the reaction increased with increase in [OH−] whereas the rate decreased with increase in [$ {\\text{IO}}^-_4 $]. Increasing the ionic strength of the medium increased the rate. The main products were identified by FT-IR, NMR, and LC-MS spectral studies. The probable mechanism was proposed. The activation parameters with respect to slow step of the mechanism were computed and discussed. Thermodynamic quantities were also calculated. Kinetic studies suggest that [Cu(H2IO6(H2O2] is the reactive species of Cu(III.

  6. Solubility of vanadium from manganese vanadates in aqueous solutions of soda ash

    Science.gov (United States)

    Khalezov, B. D.; Krasheninin, A. G.; Vatolin, N. A.; Ovchinnikova, L. A.

    2016-05-01

    It is shown that, in the course of developing the technology of pure vanadium pentoxide preparation from manganic vanadium-containing metallurgical slags, their oxidative roasting and cinder formation without alkaline additives are accompanied by the decomposition of spinelides with the formation of manganese meta- and pyrovanadates. Concentrated aqueous solutions of soda ash with an Na2CO3 concentration of 120-150 g/dm3 are accepted as a selective leaching reagent for vanadium from a cinder. Manganese metaand pyrovanadates are synthesized, and the procedure of their preparation is presented. The solubility of vanadium from manganese vanadates in aqueous solutions of soda ash at C_{Na_2 CO_3 } = 150 g/dm^3 is studied at 20-95°C for pyrovanadate and at 85-95°C for metavanadate. It is shown that vanadium should be leached from converter manganic slags roasted without alkaline metal additives at a leaching solution temperature higher than 95°C. There is a possibility to increase the vanadium content in a leaching solution to 60-80 g/dm3. The results obtained are used in the development of the technology of vanadium leaching.

  7. Removal of toxic metals from aqueous solutions by fungal biomass of Agaricus macrosporus

    Energy Technology Data Exchange (ETDEWEB)

    Melgar, M.J. E-mail: mjmelgar@lugo.usc.es; Alonso, J.; Garcia, M.A

    2007-10-15

    Fungi such as Agaricus macrosporus show potential for the removal of heavy metals from aqueous solutions contaminated by zinc, copper, mercury, cadmium or lead. This study investigated biosorption of these metals by living or non-living biomass of A. macrosporus from an acid solution, an acid solution supplemented with potassium and phosphorus, and an alkaline solution. Uptake showed a pH-dependent profile. Maximum percentage uptake of all metals was found to occur at alkaline pH (Cu 96%, Pb 89%). With living biomass, metal biosorption was greater and faster in K/P-supplemented acid medium than in non-supplemented acid medium, with equilibrium reached within 15 min for all metals, and the highest percentage uptake being of cadmium (96%). In general, the greatest differences in biosorption capacity were seen for living biomass, between supplemented and non-supplemented acid medium; the smallest differences were between living and dead biomass in alkaline medium. These results support the potential utility of A. macrosporus for heavy metal removal.

  8. Aqueous Rechargeable Alkaline CoxNi2-xS2/TiO2 Battery.

    Science.gov (United States)

    Liu, Jilei; Wang, Jin; Ku, Zhiliang; Wang, Huanhuan; Chen, Shi; Zhang, Lili; Lin, Jianyi; Shen, Ze Xiang

    2016-01-26

    An electrochemical energy storage system with high energy density, stringent safety, and reliability is highly desirable for next-generation energy storage devices. Here an aqueous rechargeable alkaline CoxNi2-xS2 // TiO2 battery system is designed by integrating two reversible electrode processes associated with OH(-) insertion/extraction in the cathode part and Li ion insertion/extraction in the anode part, respectively. The prototype CoxNi2-xS2 // TiO2 battery is able to deliver high energy/power densities of 83.7 Wh/kg at 609 W/kg (based on the total mass of active materials) and good cycling stabilities (capacity retention 75.2% after 1000 charge/discharge cycles). A maximum volumetric energy density of 21 Wh/l (based on the whole packaged cell) has been achieved, which is comparable to that of a thin-film battery and better than that of typical commercial supercapacitors, benefiting from the unique battery and hierarchical electrode design. This hybrid system would enrich the existing aqueous rechargeable LIB chemistry and be a promising battery technology for large-scale energy storage.

  9. Interactions between crystal violet and AOT in aqueous solutions and in AOT/isooctane/water microemulsions

    Institute of Scientific and Technical Information of China (English)

    HAO Xiaojuan; AN Xueqin; CHEN Zhiyun; SHEN Weiguo

    2004-01-01

    The absorbance of crystal violet (CV) in a series of aqueous solutions and a series of sodium bis(2-ethyl- hexyl) sulfosuccinate (AOT)/isooctane/water microemulsions has been determined. Association models have been used to analyse the experimental data to obtain the association constants of CV and AOT in the above two media. It was found that about up to 57% CV was associated by AOT in AOT/ isooctane/water microemulsions, which reduced the reaction rate of alkaline fading of crystal violet in the microemulsions.

  10. Electrochemical study of benzene on Pt of various surface structures in alkaline and acidic solutions

    OpenAIRE

    Montilla Jiménez, Francisco; Morallón Núñez, Emilia; Vázquez Picó, José Luis

    2002-01-01

    The electrochemical behaviour of benzene on platinum electrodes (polycrystalline and single-crystal electrodes) has been studied in acidic and alkaline solutions. In acid solutions the reduction of benzene to cyclohexane takes place in all the platinum surface structure employed, however it does not occur in alkaline media (0.1 M NaOH). In this case, the hydrogen adsorption/desorption processes displace the adsorbed benzene from the electrode surface. The oxidation of benzene is also af...

  11. Kinetics of absorption of trace iodine vapor in aqueous solution of sodium hydroxide, 1

    International Nuclear Information System (INIS)

    The absorption rate of iodine vapor in the air to water or aqueous solution of sodium hydroxide is varied considerably by the concentration of iodine vapor and sodium hydroxide in the solution. Here, experiments have been carried out on the short contact time absorption of trace iodine vapor contained in decarboxylated air into water or sodium hydroxide solution, using a laminar flow liquid column, and the absorption mechanism and the rate of iodine removal by a alkaline washing have been theoretically considered. In the case that water is used as absorbing liquid, it is necessary to evaluate the rate of hypoiodite formation in order to estimate the overall absorption rate, since hypoiodite reaction progresses at finite rate. While if aqueous solution of sodium hydroxide is used, the hypoiodite formation is fast enough to treat the absorption as the instantaneous reversible reaction at the interface. The main factors determining the reaction rate in a liquid film are the concentration of molecular iodine and hydroxyl ions, and the latter is mainly varied by electric charge balance condition in aqueous solution. (Wakatsuki, Y.)

  12. Study on Gold(Ⅰ) Solvent Extraction from Alkaline Cyanide Solution by TBP with Addition of Surfactant

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    The new solvent extraction system for gold(Ⅰ) from alkaline cyanide solution by TBP with addition of surfactant in aqueous phase was studied. The effect of various factors, such as equilibrium pH, constitution of organic phase, molar ratio of CPB∶Au(CN)2-, extraction time, aqueous/organic phase ratio, different initial gold concentration, equilibrium temperature, different diluent, different types of extractants and surfactants etc., was inspected. The results show that gold(Ⅰ) can be extracted quantitatively by controlling the quantity of surfactant (CPB); both the equilibrium pH and diluent hardly influence percent extraction. Gold(Ⅰ) percent extraction reaches more than 98% under the optimal experimental conditions. 30% vol TBP diluted by sulphonating kerosene can load gold(Ⅰ) to rather high levels. Loading capacity is in excess of 38 g/L. The extraction mechanism is discussed and the overall extraction reaction is deduced.

  13. Development of alkaline solution separations for potential partitioning of used nuclear fuels

    Energy Technology Data Exchange (ETDEWEB)

    Jarvinen, Gordon D [Los Alamos National Laboratory; Runde, Wolfgang H [Los Alamos National Laboratory; Goff, George S [Los Alamos National Laboratory

    2009-01-01

    The processing of used nuclear fuel in alkaline solution provides potentially useful new selectivity for separating the actinides from each other and f rom the fission products. Over the ast decade, several research teams around the world have considered dissolution of used fuel in alkaline solution and further partitioning in this medium as an alternative to acid dissolution. The chemistry of the actinides and fission products in alkaline soilltion requires extensive investigation to more carefully evaluate its potential for developing useful separation methods for used nuclear fueI.

  14. Acidities of Water and Methanol in Aqueous Solution and DMSO

    Science.gov (United States)

    Gao, Daqing

    2009-01-01

    The relative acidities of water and methanol have been a nagging issue. In gas phase, methanol is more acidic than water by 36.0 kJ/mol; however, in aqueous solution, the acidities of methanol and water are almost identical. The acidity of an acid in solution is determined by both the intrinsic gas-phase ionization Gibbs energy and the solvent…

  15. Synthesis and Aqueous Solution Viscosity of Hydrophobically Modified Xanthan Gum

    Institute of Scientific and Technical Information of China (English)

    QIAN Xiao-lin; WU Wen-hui; YU Pei-zhi; WANG Jian-quan

    2007-01-01

    Two xanthan gum derivatives hydrophobically modified by 4 or 8 tetradecyl chains per 100 xanthan gum structure units were synthesized. The derivatives were studied by scanning electron microscope and pyrene fluorescence spectrometry. And the aqueous solution apparent viscosity of the derivatives was investigated. The results indicate that the network of the derivatives with more hydrophobic groups is closer and tighter. With increasing of alkyl chain substitution degree, the hydrophobically associating interactions enhance in aqueous solution. Aqueous solution apparent viscosity of the derivatives increases with increasing of polymer concentration and alkyl substitution degree, and decreases with the increase of temperature. In the brine solution, the strong viscosity enhancement phenomenon appears. The interaction between the derivatives and surfactant sodium dodecylbenzene sulfonate is strong.

  16. Absorption and Chemisorption of Small Levitated Single Bubbles in Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Alexander Tollkötter

    2014-02-01

    Full Text Available The absorption and chemisorption of small bubbles with N2 or CO2 were investigated experimentally in aqueous and alkaline solutions. Different bubble sizes were studied ranging from 0.1 to 2.5 mm in alkaline concentrations of 0.1 mM to 1 M NaOH. The experiments were conducted in a device consisting of a converging microchannel with a down flowing liquid. Levitation positions of single bubbles were optically characterized. A correlation was developed for the drag force coefficient, CD, including wall effects based on the force equilibrium. A linear decrease of bubble diameters was identified with and without chemical reaction, which is referred to as a rigid bubble surface area. Measured Sherwood numbers agree well with the literature values for the investigated Reynolds number range.

  17. Methanol oxidation on Pd/Pt(poly) in alkaline solution

    Science.gov (United States)

    Maksic, A.; Rakocevic, Z.; Smiljanic, M.; Nenadovic, M.; Strbac, S.

    2015-01-01

    Bimetallic electrodes prepared by Pd nanoislands spontaneously deposited on polycrystalline platinum, Pt(poly), at submonolayer coverage were explored for methanol oxidation in alkaline media. Characterization of obtained Pd/Pt(poly) nanostructures was performed ex situ by AFM imaging, spectroscopic ellipsometry and by X-ray photoelectron spectroscopy. In situ characterization of the obtained electrodes and subsequent methanol oxidation measurements were performed by cyclic voltammetry in 0.1 M KOH. Platinum surface with 35% Pd coverage exhibited the highest catalytic activity for methanol oxidation in alkaline media, exceeding those of bare Pt and Pd. Both synergistic and electronic effects are responsible for such enhanced catalysis. The origin of the synergistic effect and possible reaction pathways for methanol oxidation were discussed taking into account the activity of obtained bimetallic electrodes for the oxidation of CO and formaldehyde, as the most probable reaction intermediates.

  18. Conductivity of Oxalic Acid in Aqueous Solution at Low Concentration

    Institute of Scientific and Technical Information of China (English)

    倪良; 韩世钧

    2005-01-01

    Oxalic acid is a weak and unsymmetrical bi-basic acid. There exist dissociation and association equilibria among the species in aqueous solution. The molar conductivity of the solution is the sum of the ionic contributions.Based on this idea, a new prediction equation of ionic conductivity was proposed at low concentration. The molar conductivities of the solution and its relevant ions were calculated respectively. The results obtained were in good agreement with those from experiments and the Quint-Viallard equation.

  19. Molecular Weight and Aggregation of Erwinia Gum in Aqueous Solutions

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Erwinia(E) gum is composed of glucose, fucose, galactose and glucuronic acid. The weight-average molecular weights Mw, number-average molecular weights Mn and intrinsic viscosities[η] of the four fractions and the unfractionated E gum in aqueous solutions at desired temperatures were studied by light scattering, membrane osmometry, size exclusion chromatography(SEC) and viscometry. The experimental results prove that E gum formed aggregates in the aqueous solution at 25 ℃ and the aggregates were broken gradually with increasing temperature. The dissociation of the aggregates of E gum in the aqueous solution started at 36 ℃, and was completed at around 90 ℃. The [η] values of E gum and its fractions are much higher than those of the conventional polymers with the similar molecular weights, and decrease with increasing NaCl concentration.

  20. Reorientation and Allied Dynamics in Water and Aqueous Solutions

    Science.gov (United States)

    Laage, Damien; Stirnemann, Guillaume; Sterpone, Fabio; Rey, Rossend; Hynes, James T.

    2011-05-01

    The reorientation of a water molecule is important for a host of phenomena, ranging over—in an only partial listing—the key dynamic hydrogen-bond network restructuring of water itself, aqueous solution chemical reaction mechanisms and rates, ion transport in aqueous solution and membranes, protein folding, and enzymatic activity. This review focuses on water reorientation and related dynamics in pure water, and for aqueous solutes with hydrophobic, hydrophilic, and amphiphilic character, ranging from tetra-methylurea to halide ions and amino acids. Attention is given to the application of theory, simulation, and experiment in the probing of these dynamics, in usefully describing them, and in assessing the description. Special emphasis is placed on a novel sudden, large-amplitude jump mechanism for water reorientation, which contrasts with the commonly assumed Debye rotational diffusion mechanism, characterized by small-amplitude angular motion. Some open questions and directions for further research are also discussed.

  1. [Extraction of alpha-cypermethrin from aqueous methanol solutions].

    Science.gov (United States)

    Shormanov, V K; Chigareva, E N; Belousova, O V

    2010-01-01

    Alpha cypermethrin was extracted from aqueous methanol solutions using hydrophobic organic solvents. The efficiency of extraction was shown to depend on the chemical nature of the solvent, the water to methanol ratio, and saturation of the aqueous methanol layer with an electrolyte. Optimal extraction of alpha-cypermethrin was achieved using toluene as the solvent under desalinization conditions. The extraction factor for the removal of the sought amount of alpha-cypermethrin from the water-methanol solution (4:1) using various solvents was calculated.

  2. Ionisation constants of inorganic acids and bases in aqueous solution

    CERN Document Server

    Perrin, D D

    2013-01-01

    Ionisation Constants of Inorganic Acids and Bases in Aqueous Solution, Second Edition provides a compilation of tables that summarize relevant data recorded in the literature up to the end of 1980 for the ionization constants of inorganic acids and bases in aqueous solution. This book includes references to acidity functions for strong acids and bases, as well as details about the formation of polynuclear species. This text then explains the details of each column of the tables, wherein column 1 gives the name of the substance and the negative logarithm of the ionization constant and column 2

  3. Predicting accurate absolute binding energies in aqueous solution

    DEFF Research Database (Denmark)

    Jensen, Jan Halborg

    2015-01-01

    Recent predictions of absolute binding free energies of host-guest complexes in aqueous solution using electronic structure theory have been encouraging for some systems, while other systems remain problematic. In this paper I summarize some of the many factors that could easily contribute 1-3 kcal......-represented by continuum models. While I focus on binding free energies in aqueous solution the approach also applies (with minor adjustments) to any free energy difference such as conformational or reaction free energy differences or activation free energies in any solvent....

  4. Degradation kinetics of benzyl nicotinate in aqueous solution

    Directory of Open Access Journals (Sweden)

    Mbah C

    2010-01-01

    Full Text Available The degradation of benzyl nicotinate in aqueous solution over a pH range of 2.0-10.0 at 50±0.2 o was studied. The degradation was determined by high performance liquid chromatography. The degradation was observed to follow apparent first-order rate kinetics and the rate constant for the decomposition at 25 o was estimated by extrapolation. The reaction was shown to be hydroxide ion catalyzed and the Arrhenius plots showed the temperature dependence of benzyl nicotinate degradation. A significant increase in the stability of benzyl nicotinate was observed when glycerol or polyethylene glycol 400 was incorporated into the aqueous solution.

  5. Removal of Phosphate from Aqueous Solution with Modified Bentonite

    Institute of Scientific and Technical Information of China (English)

    唐艳葵; 童张法; 魏光涛; 李仲民; 梁达文

    2006-01-01

    Bentonite combined with sawdust and other metallic compounds was used to remove phosphate from aqueous solutions in this study. The adsorption characteristics of phosphate on the modified bentonite were investigated, including the effects of temperature, adsorbent dosage, initial concentration of phosphate and pH on removal of phosphate by conducting a series of batch adsorption experiments. The results showed that 98% of phosphate removal rate was obtained since sawdust and bentonite used in this investigation were abundantly and locally available. It is concluded that modified bentonite is a relatively efficient, low cost and easily available adsorbent for the removal of phosphate from aqueous solutions.

  6. Valence Electronic Structure of Aqueous Solutions: Insights from Photoelectron Spectroscopy

    Science.gov (United States)

    Seidel, Robert; Winter, Bernd; Bradforth, Stephen E.

    2016-05-01

    The valence orbital electron binding energies of water and of embedded solutes are crucial quantities for understanding chemical reactions taking place in aqueous solution, including oxidation/reduction, transition-metal coordination, and radiation chemistry. Their experimental determination based on liquid-photoelectron spectroscopy using soft X-rays is described, and we provide an overview of valence photoelectron spectroscopy studies reported to date. We discuss principal experimental aspects and several theoretical approaches to compute the measured binding energies of the least tightly bound molecular orbitals. Solutes studied are presented chronologically, from simple electrolytes, via transition-metal ion solutions and several organic and inorganic molecules, to biologically relevant molecules, including aqueous nucleotides and their components. In addition to the lowest vertical ionization energies, the measured valence photoelectron spectra also provide information on adiabatic ionization energies and reorganization energies for the oxidation (ionization) half-reaction. For solutes with low solubility, resonantly enhanced ionization provides a promising alternative pathway.

  7. Glasslike Behavior in Aqueous Electrolyte Solutions

    CERN Document Server

    Turton, David A; Hefter, Glenn; Buchner, Richard; Wynne, Klaas; 10.1063/1.2906132

    2009-01-01

    When salts are added to water, the viscosity generally increases suggesting the ions increase the strength of the water's hydrogen-bond network. However, infrared pump-probe measurements on electrolyte solutions have found that ions have no influence on the rotational dynamics of water molecules implying no enhance-ment or breakdown of the hydrogen-bond network. Here we report optical Kerr-effect and dielectric relaxa-tion spectroscopic measurements, which have enabled us to separate the effects of rotational and transitional motions of the water molecules. These data show that electrolyte solutions behave like a supercooled liquid approaching a glass transition in which rotational and translational molecular motions are decoupled. It is now possible to understand previously conflicting viscosity data, nuclear magnetic resonance relaxation, and ultrafast infrared spectroscopy in a single unified picture.

  8. Glasslike behavior in aqueous electrolyte solutions.

    Science.gov (United States)

    Turton, David A; Hunger, Johannes; Hefter, Glenn; Buchner, Richard; Wynne, Klaas

    2008-04-28

    When salts are added to water, generally the viscosity increases, suggesting that the ions increase the strength of the water's hydrogen-bond network. However, infrared pump-probe measurements on electrolyte solutions have found that ions have no influence on the rotational dynamics of water molecules, implying no enhancement or breakdown of the hydrogen-bond network. Here, we report optical Kerr effect and dielectric relaxation spectroscopic measurements, which have enabled us to separate the effects of rotational and transitional motions of the water molecules. These data show that electrolyte solutions behave like a supercooled liquid approaching a glass transition in which rotational and translational molecular motions are decoupled. It is now possible to understand previously conflicting viscosity data, nuclear magnetic resonance relaxation, and ultrafast infrared spectroscopy in a single unified picture.

  9. Reaction mechanism of 3-chlorophenol with OH, H in aqueous solution

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    The reaction mechanism of 3-chlorophenol with OH, H inaqueous solution was studied by transient technology. The3-chlorophenol aqueous solutions have been saturated with air or N2previously. Under alkaline condition, the reaction of OH radicalwith 3-chlorophenol produces 3-chlorinated phenoxyl radical, withthe absorption peaks at 400 nm and 417 nm. Under neutral condition,the reaction of OH radical with 3-chlorophenol produces OH-adductwith the maximal absorption at about 340 nm. And in acid solution,the reaction of H with 3-chlorophenol produces H-adduct with themaximal absorption at about 320 nm. 3-chlorophenol is compared with4- and 2-chlorophenols from the free radical pathways. The resultsshow that the positions of chlorine on the aromatic ring stronglyinfluence the dehalogenation and degradation process.

  10. Effect of electron beam irradiation on the degradation of monochlorophenols in aqueous solution

    Institute of Scientific and Technical Information of China (English)

    ADELEKE Olukunle Francis; ZHOU Rui-min; Zu Jian-hua; Ekoko Bakambo Gracien

    2005-01-01

    Electron beam was successfully used for the degradation of 2-chlorophenol (2-CP) and 4-chlorophenol (4-CP) in aqueous solutions in this research. The effect of radiation dose on substrate degradation and dechlorination of solutions with concentration of 50 mg/L was investigated. The effect of initial concentration, pH and presence of oxygen was also investigated. The concentration of 2-CP and 4-CP remaining in solution after irradiation were measured by HPLC. The results showed that increased radiation dose led to increased degradation of the chlorophenols and increased Cl- yield. Deaeration was also found to significantly increase the rate of degradation of chlorophenols in water while degradation and dechlorination under alkaline condition was lower than at low to neutral pH.

  11. LIGHT SCATTERING OF POLYSACCHARIDE FROM LACQUER IN AQUEOUS SOLUTION

    Institute of Scientific and Technical Information of China (English)

    ZHANG Lina; DU Yumin; KUMANOTANI JU

    1989-01-01

    The polysaccharide having weight-average molecular weight Mw= 1. 09 × 105 , isolated from the sap of lac trees ( Vietnam ), was separated into 12 fractions by aqueous-phase preparative gel permeation chromatography. The molecular weights and molecular weight distributions of the fractions were measured in aqueous 0.08M KCl/0.01 M NaAc and 0.4M KCl/0.05M NaAc at pH = 7.6 by light scattering, viscometry and gel permeation chromatography. The Mark-Houwink equation in aqueous 0.08M KCl/0.01M NaAc at30 ℃ was found to be [ η] = 2.28 ×10-2 M0.52w ( cm3/g ), which indicated the polysaccharide chain in the aqueous solution to be a spherical random coil.

  12. Anodic dissolution of gold in alkaline solutions containing thiourea, thiosulfate and sulfite ions

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Gold dissolves electrochemically in alkaline solutions containing ligands to form complex ions with gold ion. Therefore, selective leaching of noble metals is expected without dissolution of base metals such as steels, aluminum alloys in scrap treatment. Gold electrodes were investigated using linear sweep voltammetry, EQCM method and potentiostatic electrolysis in alkaline solutions containing thiourea, Na2SO3 and Na2S2O3. The solution composition, electrode potential affect gold dissolution rate and current efficiency. The gold dissolved from anode electrode forms complex ions, suspension particles as compound precipitates and deposits on cathode electrode as a metal. Anodic efficiency for gold dissolution is between 10% and 22%. This is caused by the oxidation decomposition of sulfite ions and thiourea. The stability of the alkaline solution containing these elements was also estimated by capillary electrophoresis technique.

  13. Phosphorylation of glyceric acid in aqueous solution using trimetaphosphate.

    Science.gov (United States)

    Kolb, V; Orgel, L E

    1996-02-01

    The phosphorylation of glyceric acid is an interesting prebiotic reaction because it converts a simple, potentially prebiotic organic molecule into phosphate derivatives that are central to carbohydrate metabolism. We find that 0.05 M glyceric acid in the presence of 0.5 M trimetaphosphate in alkaline solution gives a mixture of 2- and 3-phosphoglyceric acids in combined yields of up to 40%. PMID:11536746

  14. Phosphorylation of Glyceric Acid in Aqueous Solution Using Trimetaphosphate

    Science.gov (United States)

    Kolb, Vera; Orgel, Leslie E.

    1996-01-01

    The phosphorylation of glyceric acid is an interesting prebiotic reaction because it converts a simple, potentially prebiotic organic molecule into phosphate derivatives that are central to carbohydrate metabolism. We find that 0.05 M glyceric acid in the presence of 0.5 M trimetaphosphate in alkaline solution gives a mixture of 2- and 3-phosphoglyceric acids in combined yields of up to 40%.

  15. Photocatalytic degradation of molinate in aqueous solutions.

    Science.gov (United States)

    Bizani, E; Lambropoulou, D; Fytianos, K; Poulios, I

    2014-11-01

    In this study, the degradation of molinate through heterogeneous photocatalysis, using two different types of the semiconductor TiO2 as photocatalyst, as well as through homogeneous treatment, applying the photo-Fenton reaction, has been investigated. As far as heterogeneous photocatalysis is concerned, the degradation of the pesticide follows apparent first-order kinetics, while the type of the catalyst and the pH value of the solution affect the degradation rate. The effect of the addition of electron scavengers (H2O2 and K2S2O8) was also studied. In the case of photo-Fenton-assisted system, the degradation also follows pseudo-first-order kinetics. Parameters such as iron's and electron scavenger's concentration and inorganic ions strongly affect the degradation rate. The extent of pesticide mineralization was investigated using dissolved organic carbon (DOC) measurements. The toxicity of the treated solution was evaluated using the Microtox test based on the luminescent bacteria Vibrio fischeri. The detoxification and mineralization efficiency was found to be dependent on the system studied, and although it did not follow the rate of pesticide disappearance, it took place in considerable extent. The study of the photodegradation treatment was completed by the determination of the intermediate by-products formed during the process, which was carried out using LC-MS/MS technique and led to similar compounds with both processes. PMID:24928378

  16. Photocatalytic degradation of molinate in aqueous solutions.

    Science.gov (United States)

    Bizani, E; Lambropoulou, D; Fytianos, K; Poulios, I

    2014-11-01

    In this study, the degradation of molinate through heterogeneous photocatalysis, using two different types of the semiconductor TiO2 as photocatalyst, as well as through homogeneous treatment, applying the photo-Fenton reaction, has been investigated. As far as heterogeneous photocatalysis is concerned, the degradation of the pesticide follows apparent first-order kinetics, while the type of the catalyst and the pH value of the solution affect the degradation rate. The effect of the addition of electron scavengers (H2O2 and K2S2O8) was also studied. In the case of photo-Fenton-assisted system, the degradation also follows pseudo-first-order kinetics. Parameters such as iron's and electron scavenger's concentration and inorganic ions strongly affect the degradation rate. The extent of pesticide mineralization was investigated using dissolved organic carbon (DOC) measurements. The toxicity of the treated solution was evaluated using the Microtox test based on the luminescent bacteria Vibrio fischeri. The detoxification and mineralization efficiency was found to be dependent on the system studied, and although it did not follow the rate of pesticide disappearance, it took place in considerable extent. The study of the photodegradation treatment was completed by the determination of the intermediate by-products formed during the process, which was carried out using LC-MS/MS technique and led to similar compounds with both processes.

  17. Demonstration of reverse symmetry waveguide sensing in aqueous solutions

    DEFF Research Database (Denmark)

    Horvath, R.; Pedersen, H.C.; Larsen, N.B.

    2002-01-01

    A reverse symmetry waveguide is presented for evanescent wave sensing in aqueous solutions. The waveguide consists of a thin polystyrene film, supported by a thicker substrate layer of nanoporous silica on glass. The nanoporous substrate layer has a refractive index of n(S)=1.193, hence, with an ......A reverse symmetry waveguide is presented for evanescent wave sensing in aqueous solutions. The waveguide consists of a thin polystyrene film, supported by a thicker substrate layer of nanoporous silica on glass. The nanoporous substrate layer has a refractive index of n(S)=1.193, hence......, with an aqueous cover refractive index of n(C)=1.331, a reverse symmetry (n(S)

  18. Drag enhancement of aqueous electrolyte solutions in turbulent pipe flow.

    Science.gov (United States)

    Doherty, Andrew P; Spedding, Peter L; Chen, John J J

    2010-04-22

    Detailed experimental results are presented for both laminar and turbulent flow of aqueous solutions in pipes of different diameters. Nonelectrolytes, such as sugar solutions followed the normal Moody pressure loss curves. Drag enhancement was demonstrated for turbulent flow of aqueous electrolyte solutions but not for laminar flow. The increased pressure drop for turbulent electrolyte flow was attributed to an electroviscous effect and a theory was developed to explain the drag enhancement. The increased pressure drop for the turbulent region of flow was shown to depend on the Debye length in the laminar sublayer on the pipe wall. Reasonable predictions of the increasing drag were obtained for both 1:1 and 2:1 electrolyte solutions. PMID:20337452

  19. Permeability in a state of partial solidification of aqueous solution

    Science.gov (United States)

    Okada, Masashi; Kang, Chaedong; Okiyama, Haruhiko

    A mushy region was formed by solidifying NaCl aqueous solution in a circular tube or a rectangular tube. The measurements of permeability were performed by changing volume fraction of liquid region in the mushy region. The dendritic ice in the solidification process was observed with a CCD microscope. The following results were obtained. The permeability increases with the volume fraction of liquid phase, and decreases with increasing the super-cooling degree of the solution or increasing the initial concentration of the solution, and is constant after the mushy region was formed. The arm space of dendrite becomes narrower as the super-cooling degree of the solution increases.

  20. Nb-TiO{sub 2} supported platinum nanocatalyst for oxygen reduction reaction in alkaline solutions

    Energy Technology Data Exchange (ETDEWEB)

    Elezovic, N.R., E-mail: nelezovic@tmf.bg.ac.rs [Institute for Multidisciplinary Research, University of Belgrade, Kneza Viseslava 1, Belgrade (Serbia); Babic, B.M. [Vinca Institute of Nuclear Sciences, Belgrade (Serbia); Radmilovic, V.R. [National Center for Electron Microscopy, LBNL University of California, Berkely (United States); Vracar, Lj.M.; Krstajic, N.V. [Faculty of Technology and Metallurgy, University of Belgrade, Belgrade (Serbia)

    2011-10-30

    Highlights: > Nb doped TiO{sub 2} catalyst support was successfully synthesized. > Synthesized support surface area was much higher comparing with sub-stoichiometric titanium oxides as supporting material. > The Nb-TiO{sub 2} supported Pt catalyst was successfully prepared and characterized by TEM technique. > Nb doped TiO{sub 2} support seems to be more suitable than carbon based support. > The change in the rate-determining step was proposed for reaction mechanism explanation. - Abstract: Platinum based nanocatalyst at home made Nb-TiO{sub 2} support was synthesized and characterized as the catalyst for oxygen reduction reaction in 0.1 mol dm{sup -3} NaOH, at 25 deg. C. Nb doped TiO{sub 2} catalyst support, containing 5% of Nb, has been synthesized by modified acid-catalyzed sol-gel procedure in non-aqueous medium. BET and X-ray diffraction (XRD) techniques were applied for characterization of synthesized supporting material. XRD analysis revealed only presence of anatase TiO{sub 2} phase in synthesized support powder. Existence of any peaks belonging to Nb compounds has not been observed, indicating Nb incorporated into the lattice. Nb-TiO{sub 2} supported Pt nanocatalyst synthesized, using borohydride reduction method, was characterized by TEM and HRTEM techniques. Platinum nanoparticles distribution, over Nb doped TiO{sub 2} support, was quite homogenous. Mean particle size of about 4 nm was found with no pronounced particle agglomeration. Electrochemical techniques: cyclic voltammetry and linear sweep voltammetry at rotating disc electrode were applied in order to study kinetics and estimate catalytic activity of this new catalyst for the oxygen reduction reaction in alkaline solution. Two different Tafel slopes were found: one close to -90 mV dec{sup -1} in low current density region and other approximately -200 mV dec{sup -1} in high current density region, which is in good accordance with literature results for oxygen reduction at Pt single crystals, as

  1. [Pulsed radiolysis of aqueous solutions of serum albumin containing naphthoquinones].

    Science.gov (United States)

    Pribush, A G; Savich, A V

    1987-01-01

    As was shown by the pulse radiolysis method the simultaneous presence of naphthoquinone and human serum albumin molecules in an aqueous solution leads to the adsorption of the former on the surface of the latter. It is suggested that in these conditions the protein tertiary structure changes. New conformation reduces the reactivity of albumin toward the hydrated electron. PMID:3628723

  2. Reactive Extraction of Alcohols from Apolar Hydrocarbons with Aqueous Solutions

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    The aqueous solutions are evaluated as sustainable reactive extraction solvents for the recovery of monohydroxyl alcohols (benzyl alcohol, 1-hexanol, cyclohexanol) present in few-percent concentrations in apolar hydrocarbons (toluene, n-hexane, and cyclohexane) by considering two approaches. An aqueous solution containing a reactive extractant, like borate salts, borate complexes, a monosalt of dicarboxylic acid,hydroxypropyl-cyclodextrins, and silver nitrate, shows limited potential to be used. Another approach, in which the alcohol is chemically modified prior to the extraction into an easy-extractable form, in this case a monoesterlcarboxylic acid, shows much more potential. An environmentally benign aqueous solution of sodium hydrogen carbonate can provide a distribution ratio of benzyl alcohol up to 200, leaving the solubility of the organic solvent in the aqueous solution unchanged relative to pure water and therefore increasing the selectivity with two orders of magnitude. The modification of aromatic, cyclo-aliphatic, and linear aliphatic alcohols can be performed efficiently in the apolar organic solvent without need for a catalyst. The recovery of the modified alcohol can be performed by back-extraction in combination with a spontaneous hydrolysis.

  3. Neodymium(3) complexing with bischloromethylphosphinic acid in aqueous solution

    International Nuclear Information System (INIS)

    High resolution spectrography is used to study Nd3+ complexing with (ClCH2)2POOH(HL) in aqueous solution. NdL2+ complex (lg Kstab = 0.44±0.04) with the corresponding absorption band with a maximum at λ=4283 A is formed in a system

  4. Gamma radiolysis of aqueous solutions of glycerin α-monochlorohydrin

    International Nuclear Information System (INIS)

    Data on γ-radiolysis of 0.1 mol/l aqueous solutions of glycerin α-monochlorohydrin (GMC) are presented. The radiolysis mechanism is considered. The rate constant of GMC reaction with esub(aq) k=(6.8+-0.8)x108 l/molxs is determined on the basis of experimental data

  5. DETERMINATION OF CHLORHEXIDINE IN SALIVA AND IN AQUEOUS-SOLUTIONS

    NARCIS (Netherlands)

    de Vries, J.; Ruben, J; Arends, J.

    1991-01-01

    A new method is presented for the determination of chlorhexidine in centrifuged saliva and in aqueous solutions by means of fluorescence spectroscopy. The method relies on complex formation between chlorhexidine and eosin. The fluorescence value of the chlorhexidine-eosin system decreases with incre

  6. Solubility of carbon dioxide in aqueous piperazine solutions

    NARCIS (Netherlands)

    Derks, P. W. J.; Dijkstra, H. B. S.; Hogendoorn, J. A.; Versteeg, G. F.

    2005-01-01

    In the present work, new experimental data are presented on the solubility of carbon dioxide in aqueous piperazine solutions, for concentrations of 0.2 and 0.6 molar piperazine and temperatures of 25, 40, and 70°C respectively. The present data, and other data available in the literature, were corr

  7. Adsorption of lead ions from aqueous solutions using clinoptilolite

    OpenAIRE

    Golomeova, Mirjana; Zendelska, Afrodita; Krstev, Boris; Golomeov, Blagoj; Blažev, Krsto; Krstev, Aleksandar

    2014-01-01

    The adsorption of lead ions from synthetic aqueous solutions was performed by using natural zeolite (clinoptilolite). In order to determine the effectivity of clinoptilolite a series of experiments were performed under batch conditions from single ion solutions. Experiments were carried out at different initial concentration of lead ions, different initial pH values and different adsorbent mass. The adsorption kinetics is reasonably fast. It means that in the first 20 min approximately 90...

  8. Adsorption of copper ions from aqueous solutions on natural zeolite

    OpenAIRE

    Zendelska, Afrodita; Golomeova, Mirjana; Blažev, Krsto; Krstev, Boris; Golomeov, Blagoj; Krstev, Aleksandar

    2015-01-01

    The adsorption of copper ions from synthetic aqueous solutions on natural zeolite (clinoptilolite) was examined. In order to determine the rate of adsorption and the copper uptake at equilibrium, a series of experiments were performed under batch conditions from single ion solutions. Equilibrium data were evaluated based on adsorption (Langmuir and Freundlich) isotherms. The adsorption kinetics is reasonably fast. In the first 20 min of the experiment, approximately 80% of Cu2+ io...

  9. Removal of azo dye from aqueous solutions using chitosan

    OpenAIRE

    Zuhair Jabbar; G. Hadi Ferdoos Sami; A , Angham

    2014-01-01

    Adsorption of Congo Red (CR) from aqueous solution onto chitosan was investigated in a batch system. The effects of solution pH, initial dye concentration, and temperature were studied. Results indicated that chitosan could be used as a biosorbent to remove the azo dyes from contaminated water. Synthesize of chitosan involved three main stages as preconditioning, demineralization, deproteinization and deacetylation. Chitosan was characterized using Fourier Transform Infrared Spectroscopy (FTI...

  10. Biosorption of mercury from aqueous solutions using highly characterised peats

    OpenAIRE

    A.M. Rizzuti; F.L. Ellis; L.W. Cosme; A.D. Cohen

    2015-01-01

    This research investigated the biosorption of mercury from aqueous solutions by six highly characterised peats. Samples of the peats were tested both in unaltered condition and after being treated with hydrochloric acid (HCl) to free up any occupied exchange sites. Other variables tested were sample dose, contact time, mixing temperature, and the concentration and pH of the mercury solution. Desorption studies were also performed, and tests were done to determine whether the peats could be re...

  11. Influence if acidity and concentration of aqueous uranyl nitrate solutions on the efficiency of uranium absorption by hydrolytic wood lignin

    International Nuclear Information System (INIS)

    Efficiency of uranium(VI) absorption by hydrolytic wood lignin from uranyl nitrate aqueous solutions under static conditions at room temperature, depending on solution acidity and uranium concentration, was studied using the methods of elementary analysis and IR spectroscopy. It was ascertained that hydrolytic lignin manifests a high ability to strong uranium(VI) absorption from low-acid and alkaline solutions. Interaction of uranium(VI) and hydrolytic lignin occurs both according to ion exchange mechanism and at the expense of donor-acceptor bonds formation

  12. Phytoremediation of Heavy Metals in Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Felix Aibuedefe AISIEN

    2010-12-01

    Full Text Available One of the major environmental problems is the pollution of water and soil by toxic heavy metals. This study investigated the phytoremediation potential of water hyacinth, for the removal of cadmium (Cd, lead (Pb and zinc (Zn. Water hyacinths were cultured in bore-hole water, supplemented with 5mg/l of Zn and Pb and 1mg/l of Cd at pH 4.5, 6.8 and 8.5. The plants were separately harvested each week for six weeks. The results showed that removal of these metals from solution was fast especially in the first two weeks, after which it became gradual till saturation point was reached. The accumulation of Cd and Zn in leaves and roots increased with increase in pH. The highest accumulation was in the roots with metal concentration of 4870mg/kg, 4150mg/kg and 710mg/kg for Zn, Pb and Cd respectively at pH 8.5. The maximum values of bioconcentration factor (BCF for Zn, Pb and Cd were 1674, 1531 and 1479 respectively, suggesting that water hyacinth was good accumulator of Zn, Pb and Cd, and could be used to treat industrial wastewater contaminated with heavy metals such as Zn, Pb and Cd.

  13. Block copolymer membranes for aqueous solution applications

    KAUST Repository

    Nunes, Suzana Pereira

    2016-03-22

    Block copolymers are known for their intricate morphology. We review the state of the art of block copolymer membranes and discuss perspectives in this field. The main focus is on pore morphology tuning with a short introduction on non-porous membranes. The two main strategies for pore formation in block copolymer membranes are (i) film casting and selective block sacrifice and (ii) self-assembly and non-solvent induced phase separation (SNIPS). Different fundamental aspects involved in the manufacture of block copolymer membranes are considered, including factors affecting the equilibrium morphology in solid films, self-assembly of copolymer in solutions and macrophase separation by solvent-non-solvent exchange. Different mechanisms are proposed for different depths of the SNIPS membrane. Block copolymer membranes can be prepared with much narrower pore size distribution than homopolymer membranes. Open questions and indications of what we consider the next development steps are finally discussed. They include the synthesis and application of new copolymers and specific functionalization, adding characteristics to respond to stimuli and chemical environment, polymerization-induced phase separation, and the manufacture of organic-inorganic hybrids.

  14. Critical droplet theory explains the glass formability of aqueous solutions.

    Science.gov (United States)

    Warkentin, Matthew; Sethna, James P; Thorne, Robert E

    2013-01-01

    When pure water is cooled at ~10(6) K / s, it forms an amorphous solid (glass) instead of the more familiar crystalline phase. The presence of solutes can reduce this required (or "critical") cooling rate by orders of magnitude. Here, we present critical cooling rates for a variety of solutes as a function of concentration and a theoretical framework for understanding these rates. For all solutes tested, the critical cooling rate is an exponential function of concentration. The exponential's characteristic concentration for each solute correlates with the solute's Stokes radius. A modification of critical droplet theory relates the characteristic concentration to the solute radius and the critical nucleation radius of ice in pure water. This simple theory of ice nucleation and glass formability in aqueous solutions has consequences for general glass-forming systems, and in cryobiology, cloud physics, and climate modeling. PMID:23383808

  15. Electrodeposition of metals from non-aqueous solutions

    International Nuclear Information System (INIS)

    Electrodeposition of metals from non-aqueous solutions is reviewed. Attention is paid mainly to surface morphology of deposits and their adhesion. The major reasons for carrying out electrodeposition in non-aqueous electrolytes (such as conventional organic solvents, ionic liquids and molten salts) are the water and air stability and the wide electrochemical window of these media. The following metals have been electrodeposited and investigated for the last 15 years: aluminum, zinc, silver, palladium, tantalum, zirconium, gadolinium, plutonium, nickel, cobalt, and other alloys.

  16. Raman spectra of amino acids and their aqueous solutions

    Science.gov (United States)

    Zhu, Guangyong; Zhu, Xian; Fan, Qi; Wan, Xueliang

    2011-03-01

    Amino acids are the basic "building blocks" that combine to form proteins and play an important physiological role in all life-forms. Amino acids can be used as models for the examination of the importance of intermolecular bonding in life processes. Raman spectra serve to obtain information regarding molecular conformation, giving valuable insights into the topology of more complex molecules (peptides and proteins). In this paper, amino acids and their aqueous solution have been studied by Raman spectroscopy. Comparisons of certain values for these frequencies in amino acids and their aqueous solutions are given. Spectra of solids when compared to those of the solute in solution are invariably much more complex and almost always sharper. We present a collection of Raman spectra of 18 kinds of amino acids ( L-alanine, L-arginine, L-aspartic acid, cystine, L-glutamic acid, L-glycine, L-histidine, L-isoluecine, L-leucine, L-lysine, L-phenylalanine, L-methionone, L-proline, L-serine, L-threonine, L-tryptophan, L-tyrosine, L-valine) and their aqueous solutions that can serve as references for the interpretation of Raman spectra of proteins and biological materials.

  17. Solid-like mechanical behaviors of ovalbumin aqueous solutions.

    Science.gov (United States)

    Ikeda, S; Nishinari, K

    2001-04-12

    Flow and dynamic mechanical properties of ovalbumin (OVA) aqueous solutions were investigated. OVA solutions exhibited relatively large zero-shear viscosity values under steady shear flow and solid-like mechanical responses against oscillating small shear strains, that is, the storage modulus was always larger than the loss modulus in the examined frequency range (0.1--100 rad s(-1)). These results suggest that dispersed OVA molecules arranged into a colloidal crystal like array stabilized by large interparticle repulsive forces. However, marked solid-like mechanical behaviors were detected even when electrostatic repulsive forces among protein molecules were virtually absent, which could not be explained solely on the basis of conventional Derjaguin--Landau--Verwey--Overbeek (DLVO) theory. Large non-DLVO repulsive forces seem to stabilize native OVA aqueous solutions.

  18. Cellulose conversion to polyols on supported Ru catalysts in aqueous basic solution

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    It is of great significance and challenge to achieve direct conversion of cellulose to specific polyols,e.g.,ethylene glycol and propylene glycol.For such selective conversion,a novel one-pot approach was studied by combination of alkaline hydrolysis and hydrogenation on supported Ru catalysts.A wide range of bases including solid bases,e.g.,Ca(OH)2 and La2O3,and phosphate buffers were examined in the cellulose reaction in water,and the cellulose conversions and polyol products depended largely on the basicity or pH values in the aqueous solutions.Ethylene glycol,1,2-propanediol,and especially 1,2,5-pentanetriol were obtained with selectivities of 15%,14% and 22%,respectively,at 38% cellulose conversion at pH 8 in phosphate buffer solution.These preliminary results provide potentials for efficient conversion of cellulose to targeted polyols by using the advantages of bases.

  19. Photolysis kinetics and influencing factors of bisphenol S in aqueous solutions

    Institute of Scientific and Technical Information of China (English)

    Guiping Cao; Jilai Lu; Gongying Wang

    2012-01-01

    The photodegradation of bisphenol S (BPS) in aqueous solutions was studied under different conditions.Photolysis and kinetics were investigated,as were the photolysis mechanism and the influences of initial pH value,light source,and environmental substances in water.The results showed that the photolysis of BPS occurred under UV light,and the rate increased with light source intensity.The photolysis of 5.0-50.0 mg/L BPS in water followed first-order kinetics:the rate was Υ =0.0161Caps under a 40-W UV-lamp,and the degradation half-life was 43.1 min.Due to its absorption of light,direct photolysis of BPS was a predominant pathway for BPS but was not obviously affected by reactive oxygen species.The results confirmed that the photolysis rates of BPS in alkaline water solution were faster than those in acidic and neutral water solution because of the ionization of BPS.The photodegradation rate of BPS increased in the presence of chloride and ferric ions,while the rate was inhibited by nitrate and phosphate in aqueous solution.

  20. Photolysis kinetics and influencing factors of bisphenol S in aqueous solutions.

    Science.gov (United States)

    Cao, Guiping; Lu, Jilai; Wang, Gongying

    2012-01-01

    The photodegradation of bisphenol S (BPS) in aqueous solutions was studied under different conditions. Photolysis and kinetics were investigated, as were the photolysis mechanism and the influences of initial pH value, light source, and environmental substances in water. The results showed that the photolysis of BPS occurred under UV light, and the rate increased with light source intensity. The photolysis of 5.0-50.0 mg/L BPS in water followed first-order kinetics: the rate was gamma = 0.0161C(BPS) under a 40-W UV-lamp, and the degradation half-life was 43.1 min. Due to its absorption of light, direct photolysis of BPS was a predominant pathway for BPS but was not obviously affected by reactive oxygen species. The results confirmed that the photolysis rates of BPS in alkaline water solution were faster than those in acidic and neutral water solution because of the ionization of BPS. The photodegradation rate of BPS increased in the presence of chloride and ferric ions, while the rate was inhibited by nitrate and phosphate in aqueous solution.

  1. Methylene blue adsorption of GMZ bentonite and the effect of hyper-alkaline solution erosion

    International Nuclear Information System (INIS)

    The method of combining the halo method with the spectrometer method, was used to study on the Methylene blue (MB) adsorption of Gaomiaozi (GMZ) bentonite, which had been eroded by hyper-alkaline solution, to investigate the mechanism of the effect of hyper-alkaline pore water on the buffer/backfill properties of GMZ bentonite. Results present, method employed in this article is brief and feasible, and high accuracy; The total specific surface area calculated by the test of MB adsorption is more accurate than the method of ethylene glycol monomethyl ether (EGIVIE). The MB adsorption of samples, which had been eroded by hyper-alkaline solution, decreases with the increase of the concentration of hyper-alkaline solution, and the change law agrees with the variation of the mass percentage of montmorillonite in bentonite tested by X- Ray diffraction (XRD). Therefore, the erosion of hyper-alkaline pore water might dissolve montmorillonite, which is the effective composition of bentonite, and destroy the tetrahedron- octahedron-tetrahedron (T-O-T) structure of montmorillonite, then lead to the decrease of cation exchange capability and the specific surface area of montmorillonite, and the the macroscopic expressions are the decrease of MB adsorption, the swelling potential and the increase of permeability. (authors)

  2. Dephosphorization of Steelmaking Slag by Leaching with Acidic Aqueous Solution

    Science.gov (United States)

    Qiao, Yong; Diao, Jiang; Liu, Xuan; Li, Xiaosa; Zhang, Tao; Xie, Bing

    2016-09-01

    In the present paper, dephosphorization of steelmaking slag by leaching with acidic aqueous solution composed of citric acid, sodium hydroxide, hydrochloric acid and ion-exchanged water was investigated. The buffer solution of C6H8O7-NaOH-HCl system prevented changes in the pH values. Kinetic parameters including leaching temperature, slag particle size and pH values of the solution were optimized. The results showed that temperature has no obvious effect on the dissolution ratio of phosphorus. However, it has a significant effect on the dissolution ratio of iron. The dephosphorization rate increases with the decrease of slag particle size and the pH value of the solution. Over 90% of the phosphorus can be dissolved in the solution while the corresponding leaching ratio of iron was only 30% below the optimal condition. Leaching kinetics of dephosphorization follow the unreacted shrinking core model with a rate controlled step by the solid diffusion layer, the corresponding apparent activation energy being 1.233 kJ mol-1. A semiempirical kinetic equation was established. After leaching, most of the nC2S-C3P solid solution in the steelmaking slag was selectively dissolved in the aqueous solution and the iron content in the solid residue was correspondingly enriched.

  3. Rheological properties of novel thermo-responsive polycarbonates aqueous solutions

    Institute of Scientific and Technical Information of China (English)

    王月霞; 谭业邦; 黄晓玲

    2008-01-01

    Thermo-responsive multiblock polycarbonates were facilely synthesized by covalently binding poly(ethylene glycol)(PEG) and poly(propylene glycol)(PPG) blocks,using triphosgene as coupling agent and pyridine as catalyst.The aqueous solutions of thermo-responsive polycarbonates were investigated by rheological measurements.Steady-state shear measurements reveal that the polycarbonate solutions exhibit shear-thinning behavior and the hydrophilic content has a pronounced effect on the flow behavior of the polycarbonates aqueous solutions.The shear viscosity decreases with increasing poly(ethylene oxide)(PEO) composition.The increase of viscosity with increasing concentration is probably attributed to the formation of stronger network owing to interchain entanglement of PEO block at higher concentration.When the flow curves are fitted to the power law model,flow index is obtained to be less than 1,as exhibiting typical pesudoplastic fluid.The viscoelastic properties of the system also show close dependence on the composition of polycarbonates.Temperature sweep confirms that the multiblock polycarbonates exhibit thermo-responsive properties.For 7% aqueous solution of polycarbonate with composition ratio of EO to PO of 1/1,the sol-gel transition occurs at 37 ℃,which makes the system suitable as an injectable drug delivery system.

  4. Formation of magnetite (Fe3O4)in aqueous media and properties of the interface magnetite/solution

    International Nuclear Information System (INIS)

    The formation of Fe3O4 particles in aqueous media and the properties of the Fe3O4/aqueous solution interface are studied. This system is of particular interest in nuclear reactor chemistry, since Fe3O4 was identified as the main component of the corrosion products of nuclear power plants cooled with pressurized water, of the Atucha I and II, and Embalse type. Four methods for the synthesis of Fe3O4 are described: a) controlled oxidation of Fe(OH)2 in the presence of NaNO3 at 25 deg C; b) controlled oxidation of Fe(OH)2 in the presence of NaNO3 and N2H4 and at 100 deg C; c) alkalinization of a F2+ and Fe3+ solutions at 80 deg C; d) simultaneous oxidation and alkalinization of a Fe2+. The interfacial properties of Fe3O4 particles suspended in aqueous solutions of indifferent electrolytes are described. These properties are essential for the activity transport associated with the corrosion products. Finally, the adsorption of H3BO3, Hsub(n)PO4sup(n-3) and n Co(II) in the Fe3O4/solution interface at 30 deg C. It is concluded that the adsorbed species are chemically bonded to surface metal ions. (M.E.L.)

  5. Solid / solution interaction: The effect of carbonate alkalinity on adsorbed thorium

    Science.gov (United States)

    LaFlamme, Brian D.; Murray, James W.

    1987-02-01

    Elevated activities of dissolved Th have been found in Soap Lake, an alkaline lake in Eastern Washington. Dissolved 232Th ranges from less than 0.001 to 4.9 dpm/L compared to about 1.3 × 10 -5 dpm/ L in sea water. The enhanced activity in the lake coincides with an increase in carbonate alkalinity. Experiments were conducted to evaluate the effect of pH, ionic strength and carbonate alkalinity on Th adsorption on goethite. Thorium (10 -13 M total) in the presence of 5.22 mg/L α-FeOOH and 0.1 M NaNO 3 has an adsorption edge from pH 2-5. At pH 9.0 ± 0.6 the percent Th absorbed on the solid began to decrease from 100% at 100 meq/L carbonate alkalinity and exhibited no adsorption above 300 meq/L. The experimental data were modeled to obtain the intrinsic adsorption equilibrium constants for Th hydrolysis species. These adsorption constants were incorporated in the model to interpret the observed effect of carbonate alkalinity on Th adsorption. There are two main effects of the alkalinity. To a significant degree the decrease in Th adsorption is due to competition of HCO -3 and CO 2-3 ions for surface sites. Dissolved Th carbonate complexes also contribute to the increase of Th in solution.

  6. Adsorption of cadmium from aqueous solutions by perlite.

    Science.gov (United States)

    Mathialagan, T; Viraraghavan, T

    2002-10-14

    The present study examined the use of perlite for the removal of cadmium from aqueous solutions. The effects of pH and contact time on the adsorption process were examined. The optimum pH for adsorption was found to be 6.0. Residual cadmium concentration reached equilibrium in 6h and the rate of cadmium adsorption by perlite was rapid in the first hour of the reaction time. Ho's pseudo-second-order model best described the kinetics of the reaction. Batch adsorption experiments conducted at room temperature (22+/-1 degrees C) showed that the adsorption pattern followed the Freundlich isotherm model. The maximum removal of cadmium obtained from batch studies was 55%. Thomas model was used to describe the adsorption data from column studies. The results generally showed that perlite could be considered as a potential adsorbent for cadmium removal from aqueous solutions.

  7. Removal of methyl violet from aqueous solution by perlite.

    Science.gov (United States)

    Doğan, Mehmet; Alkan, Mahir

    2003-11-01

    The use of perlite for the removal of methyl violet from aqueous solutions at different concentration, pH, and temperature has been investigated. Adsorption equilibrium is reached within 1 h. The capacity of perlite samples for the adsorption of methyl violet was found to increase with increasing pH and temperature and decrease with expansion and increasing acid-activation. The adsorption isotherms are described by means of the Langmuir and Freundlich isotherms. The adsorption isotherm was measured experimentally at different conditions and the experimental data were correlated reasonably well by the adsorption isotherm of Langmuir. The order of heat of adsorption corresponds to a physical reaction. It is concluded that the methyl violet is physically adsorbed onto the perlite. The removal efficiency (P) and dimensionless separation factor (R) have shown that perlite can be used for removal of methyl violet from aqueous solutions, but unexpanded perlite is more effective.

  8. Degradation of Sodium-Polyacrylate in Dilute Aqueous Solution, II

    Science.gov (United States)

    Saita, Takao; Matumura, On

    1983-08-01

    It has been found that Na-PAA molecules in dilute aqueous solution are degraded by shearing stress, oxidation and photolysis during usual viscosity measurements with a capillary viscometer. The results of previous viscosity measurements, mainly about the mechanochemical degradation in air and in air-free conditions, showed that the degradation rate increases with increasing shear stress, and with decreasing polymer concentration. In this work, the effects of the molecular weight and temperature on the degradation rate are measured using a capillary viscometer in air, and the photodegradation of Na-PAA and PAA in aqueous solution irradiated with UV light are studied by viscosity measurements in air, and by UV absorption and ESR methods. The results show that the degradation of molecules is enhanced by an increase in the molecular weight and strongly accelerated by a rise in temperature and by UV irradiation, and is accompanied by free-radical chain reactions.

  9. A lithium ion battery using an aqueous electrolyte solution.

    Science.gov (United States)

    Chang, Zheng; Li, Chunyang; Wang, Yanfang; Chen, Bingwei; Fu, Lijun; Zhu, Yusong; Zhang, Lixin; Wu, Yuping; Huang, Wei

    2016-01-01

    Energy and environmental pollution have become the two major problems in today's society. The development of green energy storage devices with good safety, high reliability, high energy density and low cost are urgently demanded. Here we report on a lithium ion battery using an aqueous electrolyte solution. It is built up by using graphite coated with gel polymer membrane and LISICON as the negative electrode, and LiFePO4 in aqueous solution as the positive electrode. Its average discharge voltage is up to 3.1 V and energy density based on the two electrode materials is 258 Wh kg(-1). It will be a promising energy storage system with good safety and efficient cooling effects. PMID:27328707

  10. Photodegradation of Norfloxacin in aqueous solution containing algae

    Institute of Scientific and Technical Information of China (English)

    Junwei Zhang; Dafang Fu; Jilong Wu

    2012-01-01

    Photodegradation of Norfloxacin in aqueous solution containing algae under a medium pressure mercury lamp (15 W,λmax =365 nm) was investigated.Results indicated that the photodegradation of Norfloxacin could be induced by the algae in the heterogeneous algaewater systems.The photodegradation rate of Norfloxacin increased with increasing algae concentration,and was greatly influenced by the temperature and pH of solution.Meanwhile,the cooperation action of algae and Fe(Ⅲ),and the ultrasound were beneficial to photodegradation of Norfloxaciu.The degradation kinetics of Norfloxacin was found to follow the pseudo zero-order reaction in the suspension of algae.In addition,we discussed the photodegradation mechanism of Norfloxacin in the suspension of algae.This work will be helpful for understanding the photochemical degradation of antibiotics in aqueous environment in the presence of algae,for providing a new method to deal with antibiotics pollution.

  11. A lithium ion battery using an aqueous electrolyte solution

    Science.gov (United States)

    Chang, Zheng; Li, Chunyang; Wang, Yanfang; Chen, Bingwei; Fu, Lijun; Zhu, Yusong; Zhang, Lixin; Wu, Yuping; Huang, Wei

    2016-01-01

    Energy and environmental pollution have become the two major problems in today’s society. The development of green energy storage devices with good safety, high reliability, high energy density and low cost are urgently demanded. Here we report on a lithium ion battery using an aqueous electrolyte solution. It is built up by using graphite coated with gel polymer membrane and LISICON as the negative electrode, and LiFePO4 in aqueous solution as the positive electrode. Its average discharge voltage is up to 3.1 V and energy density based on the two electrode materials is 258 Wh kg−1. It will be a promising energy storage system with good safety and efficient cooling effects. PMID:27328707

  12. A lithium ion battery using an aqueous electrolyte solution

    Science.gov (United States)

    Chang, Zheng; Li, Chunyang; Wang, Yanfang; Chen, Bingwei; Fu, Lijun; Zhu, Yusong; Zhang, Lixin; Wu, Yuping; Huang, Wei

    2016-06-01

    Energy and environmental pollution have become the two major problems in today’s society. The development of green energy storage devices with good safety, high reliability, high energy density and low cost are urgently demanded. Here we report on a lithium ion battery using an aqueous electrolyte solution. It is built up by using graphite coated with gel polymer membrane and LISICON as the negative electrode, and LiFePO4 in aqueous solution as the positive electrode. Its average discharge voltage is up to 3.1 V and energy density based on the two electrode materials is 258 Wh kg‑1. It will be a promising energy storage system with good safety and efficient cooling effects.

  13. Polyamide nanofiltration membranes to remove aniline in aqueous solutions.

    Science.gov (United States)

    Hidalgo, A M; León, G; Gómez, M; Murcia, M D; Bernal, M D; Ortega, S

    2014-01-01

    Aniline is commonly used in a number of industrial processes. It is known to be a harmful and persistent pollutant and its presence in wastewater requires treatment before disposal. In this paper, the effectiveness of nanofiltration (NF) to remove aniline from aqueous solutions is studied in a flat membrane test module using two thin-layer composite membranes of polyamide (NF97 and NF99HF). The influence of different operational variables (applied pressure, feed concentration and pH) on the removal of aniline from synthetic aqueous solutions was analysed. The experimental NF results are compared with results previously obtained by reverse osmosis. Based on this comparative study, the effective order for aniline rejection is: HR98PP > NF97 > DESAL3B > SEPA-MS05 > NF99HF. PMID:24701913

  14. Diketopiperazine-mediated peptide formation in aqueous solution

    Science.gov (United States)

    Nagayama, M.; Takaoka, O.; Inomata, K.; Yamagata, Y.

    1990-05-01

    Though diketopiperazines (DKP) are formed in most experiments concerning the prebiotic peptide formation, the molecules have not been paid attention in the studies of chemical evolution. We have found that triglycine, tetraglycine or pentaglycine are formed in aqueous solution of glycine anhydride (DKP) and glycine, diglycine or triglycine, respectively. A reaction of alanine with DKP resulted in the formation of glycylglycylalanine under the same conditions. These results indicate that the formation of the peptide bonds proceeds through the nucleophilic attack of an amino group of the amino acids or the oligoglycines on the DKP accompanied by the ring-opening. The formation of glycine anhydride, di-, tri- and tetraglycine was also observed in a mixed aqueous solution of urea and glycine in an open system to allow the evaporation of ammonia. A probable pathway is proposed for prebiotic peptide formation through diketopiperazine on the primitive Earth.

  15. SWELLING EQUILIBRIUM OF NONIONIC POLYACRYLAMIDE HYDROGEL IN AQUEOUS SALT SOLUTIONS

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    A series of nonionic polyacrylamide hydrogels, using acrylamide as monomer and N,N’-methylene diacrylamide as crosslinking agent, were prepared by the free radical polymerization in aqueous solution. Swelling equilibria for the gels were carried out in aqueous solutions of NaCl, KCl, CaCl2, Na2HPO4 and K2HPO4 with concentration ranging from 10-3 to 5mol/kgH2O at 25℃. Experimental results revealed that the chlorides and phosphates cause a different behavior at higher salt concentration. The swelling ratio increases with increasing concentration of chlorides salts, while decreases with the increased phosphates salt concentration. The phenomena seem to be related to the different interactions of chloride and hydrogen phosphate ions with the network groups. Furthermore, the effects of different concentration of crosslinking agent and total monomers on gel swelling performance were also investigated.

  16. Radiolytic degradation of malathion and lindane in aqueous solutions

    International Nuclear Information System (INIS)

    Degradation of malathion and lindane pesticides present in an aqueous solution was investigated on a laboratory scale upon gamma-irradiation from a 60Co source. The effects of pesticide group, presence of various additives and absorbed dose on efficiency of pesticide degradation were investigated. Gamma-irradiation was carried out in distilled water solutions (malathion and lindane) and in combination with humic solution (HS), nitrous oxide (N2O) and HS/N2O (lindane) over the range 0.1-2 kGy (malathion) and 5-30 kGy (lindane). Malathion was easily degraded at low absorbed doses compared to lindane in distilled water solutions. Absorbed doses required to remove 50% and 90% of initial malathion and lindane concentrations in distilled water solutions were 0.53 and 1.77 kGy (malathion) and 17.97 and 28.79 kGy (lindane), respectively. The presence of HS, N2O and HS/N2O additives in aqueous solutions, significantly improved the effectiveness of radiolytic degradation of lindane. Chemical analysis of the pesticides and the by-products resulted from the radiolytic degradation were made using a gas chromatography associated with mass spectrometry (GC-MS). Additionally, the final degradation products of irradiation as detected by ion chromatography (IC) were acetic acid and traces of some anions (phosphate and chloride).

  17. Angular correlation of annihilation photons in frozen aqueous solutions

    DEFF Research Database (Denmark)

    Milosevic-Kvajic, M.; Mogensen, O. E.; Kvajic, G.;

    1972-01-01

    Linear‐slit angular correlation curves were obtained at about −140°C for frozen aqueous solutions of HF, HCl, HBr, HI, NH3, FeCl2, FeCl3, NaI, H2SO4, NHO3, MnSO4, KMnO4, K2Cr2O7, NaOH, and LiOH. We found no appreciable influence of a 4% concentration of the last seven impurities. Only halide...

  18. Determination of concentration of saturated ferrocene in aqueous solution

    OpenAIRE

    Aoki, Koichi

    2013-01-01

    Chun Ouyang, Koichi Jeremiah Aoki, Jingyuan Chen, Toyohiko Nishiumi, Bo Wang Department of Applied Physics, University of Fukui, Bunkyo, Fukui, Japan Abstract: The solubility of ferrocene in aqueous solution is known to be approximately 0.04 mmol/dm3. The solubility values determined by voltammetry have been overestimated because of adsorption on electrodes. This work deals with discerning diffusion from adsorption by altering not only the voltammetric time scale but also the solvents used. ...

  19. EXAFS studies of actinide ions in aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Karim, D P; Georgopoulos, P; Knapp, G S

    1979-01-01

    The applicability of the EXAFS technique in the study of actinide systems is discussed. Uranium L/sub III/-edge spectra obtained on an in-lab rotating anode EXAFS facility are presented and analyzed for crystalline UO/sub 2/F/sub 2/ and aqueous solutions containing hexavalent uranium ions. Methods for the extension of the technique to more dilute systems are discussed.

  20. Ozone chemistry in aqueous solution : ozone decomposition and stabilisation

    OpenAIRE

    Eriksson, Margareta

    2005-01-01

    Ozone is used in many applications in the industry as an oxidising agent for example for bleaching and sterilisation. The decomposition of ozone in aqueous solutions is complex, and is affected by many properties such as, pH, temperature and substances present in the water. Additives can either accelerate the decomposition rate of ozone or have a stabilising effect of the ozone decay. By controlling the decomposition of ozone it is possible to increase the oxidative capacity of ozone. In this...

  1. Pulse radiolysis of aqueous lignin solutions with acryl monomers

    International Nuclear Information System (INIS)

    Radiation-induced polymerization in aqueous solutions of methylmethacrylate and methylacrylate with and without lignin added was studied by pulse radiolysis method. Optical spectra of intermediates taking part in the chain evolution were obtained. The rate constant of the chain polymerization termination diminished when lignin added from 1.2 x 109 up to 2 x 108 mol-1 s-1. A reaction scheme of radiation-induced polymerization was proposed which included the lignin entering in chain propagation reactions. (author)

  2. Pulse Radiolysis of Adrenaline in Acid Aqueous Solutions

    DEFF Research Database (Denmark)

    Gohn, M.; Getoff, N.; Bjergbakke, Erling

    1976-01-01

    Pulse radiolysis of adrenaline in acid aqueous solutions (pH 1–3) was carried out. The rate constants for the reactions of adrenaline with H and OH were determined: k(H + adr.) = (0·9±0·1) × 109 dm3 mol−1s−1; k(OH + adr.) = (1·65±0·15) × 1010 dm3 mol−1s−1. The H-adduct of adrenaline has two λmax...

  3. Fluorescence of lanthanide(III) complexes in aqueous solutions

    International Nuclear Information System (INIS)

    The fluorescence of lanthanide ions and of their complexes with EDTA, NTA and AA in aqueous solutions was investigated. It has been shown that the fluorescence band intensities of Sm(III), Eu(III), Gd(III), Tb(III) and Dy(III) complexes depend on the pH and the complexing agent concentration. Fluorescence measurements were used to characterise the lanthanide complexes formed and an attempt was made to interpret the results theoretically. (Author)

  4. Defect structure of cubic solid solutions of alkaline earth and rare earth fluorides

    NARCIS (Netherlands)

    DenHartog, HW

    1996-01-01

    In this paper we will consider the disorder in some cubic solid solutions consisting of one of the alkaline earth fluorides and one of the rare earth fluorides. This is an attractive group of model materials, because these materials have a rather simple overall cubic structure. We will discuss the m

  5. Dissolution of gaseous methyl iodide into aqueous sodium hydroxide solutions

    International Nuclear Information System (INIS)

    Absorption process of gaseous methyl iodide by water or sodium hydroxide solutions was investigated using a semi-flow type experimental apparatus by measuring the concentration of all measurable chemical species in both the gas and the liquid phase. The experimental temperature ranged from 288 to 311 K and the gaseous methyl iodide and aqueous sodium hydroxide concentrations were approximately 0.6 x 10-3 to 7 x 10-3 and 0 to 0.2 mol/dm3, respectively. It is estimated that the dissolution of methyl iodide into the sodium hydroxide solution proceeds according to the following steps. Step (1) Methyl iodide in air dissolves physically into the aqueous phase. Physical dissolution process obeys Henry's law. Step (2) Methyl iodide dissolved into the aqueous phase is decomposed by a base catalytic hydrolysis and produces methyl alcohol and iodide ion. The equilibrium constants of physical dissolution were obtained from the steady concentration in both the gas and the liquid phases in the semi-flow type experiment because the hydrolysis reaction rate of methyl iodide is very slow in comparison with the physical dissolution in this experimental conditions. The obtained value of the standard heat of solution of methyl iodide into water was 7.2 kcal/mol. Salting-out effect was observed when the concentration of sodium hydroxide in the absorbent was over 0.01 mol/dm3. (auth.)

  6. Dermal absorption of a dilute aqueous solution of malathion

    Directory of Open Access Journals (Sweden)

    Scharf John

    2008-01-01

    Full Text Available Malathion is an organophosphate pesticide commonly used on field crops, fruit trees, livestock, agriculture, and for mosquito and medfly control. Aerial applications can result in solubilized malathion in swimming pools and other recreational waters that may come into contact with human skin. To evaluate the human skin absorption of malathion for the assessment of risk associated with human exposures to aqueous solutions, human volunteers were selected and exposed to aqueous solutions of malathion. Participants submerged their arms and hands in twenty liters of dilute malathion solution in either a stagnant or stirred state. The "disappearance method" was applied by measuring malathion concentrations in the water before and after human exposure for various periods of time. No measurable skin absorption was detected in 42% of the participants; the remaining 58% of participants measured minimal absorbed doses of malathion. Analyzing these results through the Hazard Index model for recreational swimmer and bather exposure levels typically measured in contaminated swimming pools and surface waters after bait application indicated that these exposures are an order of magnitude less than a minimal dose known to result in a measurable change in acetylcholinesterase activity. It is concluded that exposure to aqueous malathion in recreational waters following aerial bait applications is not appreciably absorbed, does not result in an effective dose, and therefore is not a public health hazard.

  7. Catalytic oxidation of calcium sulfite in solution/aqueous slurry

    Institute of Scientific and Technical Information of China (English)

    WU Xiao-qin; WU Zhong-biao; WANG Da-hui

    2004-01-01

    Forced oxidation of calcium sulfite aqueous slurry is a key step for the calcium-based flue gas desulfurization(FGD) residue. Experiments were conducted in a semi-batch system and a continuous flow system on lab scales. The main reactor in semi-batch system is a 1000 ml volume flask. It has five necks for continuous feeding of gas and a batch of calcium sulfite solution/aqueous slurry. In continuous flow system, the main part is a jacketed Pyrex glass reactor in which gas and solution/aqueous slurry are fed continuously. Calcium sulfite oxidation is a series of complex free-radical reactions. According to experimental results and literature data, the reactions are influenced significantly by manganese as catalyst. At low concentration of manganese and calcium sulfite, the reaction rate is dependent on 1.5 order of sulfite concentration, 0.5 order of manganese concentration, and zero order of oxygen concentration in which the oxidation is controlled by chemical kinetics. With concentrations of calcium sulfite and manganese increasing, the reactions are independent gradually on the constituents in solution but are impacted by oxygen concentration. Manganese can accelerate the free-radical reactions, and then enhances the mass transfer of oxygen from gas to liquid. The critical concentration of calcium sulfite is 0.007 mol/L, manganese is 10-4 mol/L, and oxygen is of 0.2-0.4 atm.

  8. Observations on the Solubility of Skeletal Carbonates in Aqueous Solutions.

    Science.gov (United States)

    Chave, K E; Deffeyes, K S; Weyl, P K; Garrels, R M; Thompson, M E

    1962-07-01

    Carbonate skeletal materials of marine organisms exhibit a wide range of solubilities in aqueous solutions. In most cases, the dissolution of the carbonate mineral is irreversible and therefore the material can have no true equilibrium solubility. Relative solubilities have been measured in distilled water and in sea water. The least soluble mineral appears to be calcite with low magnesium content; the most soluble is calcite containing 20 to 30 percent MgCO(3) in solid solution. Aragonite has an intermediate solubility. PMID:17774123

  9. Radiolysis of berberine or palmatine in aqueous solution

    Science.gov (United States)

    Marszalek, Milena; Wolszczak, Marian

    2011-01-01

    The reactions of hydrated electron (eaq-), hydrogen atom (H rad ) (reducing species) and Cl2•-, Br2•-, N,O•H radicals (oxidizing species) with berberine or palmatine in aqueous solution have been studied by steady-state and pulse radiolysis. The spectra of transient intermediates, leading to the final products, are presented. The rate constants of the reaction of eaq- and rad OH radical with both alkaloids in the homogenous solution and in the presence of DNA are reported. It is demonstrated that the primary products of the reaction of berberine and palmatine with eaq- and radicals generated during radiolysis are unstable and undergo further reactions.

  10. Direct photolysis of nitroaromatic compounds in aqueous solutions

    Institute of Scientific and Technical Information of China (English)

    CHEN Bing; YANG Chun; GOH Ngoh Khang

    2005-01-01

    The direct photolysis of nitrobenzene and nitrophenols in aqueous solutions irradiated by polychromatic light were investigated.Several aromatic intermediates were identified as three nitrophenol isomers, nitrohydroquinone, nitrosobenzene, nitrocatechol, catechol and phenol. Nitrite and nitrate ions were also detected in the irradiated solution indicating direct photolysis of nitrobenzene or nitrophenols.The degradation of nitrobenzene and nitrophenols and the formation of three nitrophenol isomers were observed to follow zero-order kinetics. The quantum yields for nitrobenzene and nitrophenols removal are about 10-3 and 10-3-10-4 respectively. The mechanism for nitrobenzene degradation was suggested to follow mainly nitro-nitrite intramolecular arrangement.

  11. Characterization of aqueous silver nitrate solutions for leakage tests

    OpenAIRE

    José Ferreira Costa; Walter Luiz Siqueira; Alessandro Dourado Loguercio; Alessandra Reis; Elizabeth de Oliveira; Cláudia Maria Coelho Alves; José Roberto de Oliveira Bauer; Rosa Helena Miranda Grande

    2011-01-01

    OBJECTIVE: To determine the pH over a period of 168 h and the ionic silver content in various concentrations and post-preparation times of aqueous silver nitrate solutions. Also, the possible effects of these factors on microleakage test in adhesive/resin restorations in primary and permanent teeth were evaluated. MATERIAL AND METHODS: A digital pHmeter was used for measuring the pH of the solutions prepared with three types of water (purified, deionized or distilled) and three brands of silv...

  12. Biosorption of mercury from aqueous solutions using highly characterised peats

    Directory of Open Access Journals (Sweden)

    A.M. Rizzuti

    2015-02-01

    Full Text Available This research investigated the biosorption of mercury from aqueous solutions by six highly characterised peats. Samples of the peats were tested both in unaltered condition and after being treated with hydrochloric acid (HCl to free up any occupied exchange sites. Other variables tested were sample dose, contact time, mixing temperature, and the concentration and pH of the mercury solution. Desorption studies were also performed, and tests were done to determine whether the peats could be re-used for mercury biosorption. The results indicate that all six peat types biosorb mercury from aqueous solutions extremely well (92−100 % removal and that their mercury removal capacities are not significantly affected by manipulation of the various factors tested. The factor that had the greatest impact on the mercury removal capacities of the peats was the pH of the mercury solution. The optimal mercury solution pH for mercury removal was in the range 5−7 for four of the peats and in the range 2−3 for the other two. The desorption results indicate that it may be possible to recover up to 41 % of the removed mercury. All of the peat types tested can be repeatedly re-used for additional mercury biosorption cycles. Hence, their disposal should not become a hazardous waste problem.

  13. Corrosion behavior of bulk metallic glasses in different aqueous solutions

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    The corrosion behavior of as-cast fully amorphous, structural relaxed amorphous and crystallized Fe65.5Cr4Mo4Ga4P12C5B5.5 bulk metallic glasses (BMGs) in NaCl, HCl and NaOH solutions was investigated by electrochemical polarization and immersion methods. X-ray photoelectron spectroscopy measurements was used to analyze the changes of the elements on the alloy surface before and after immersion in various solutions. The corrosion resistance of the Fe65.5Cr4Mo4Ga4P12C5B5.5 BMG was better than its structural relaxation/crystallization counterparts and common alloys (such as stainless steel, carbonized steel, and steel) in the selected aqueous solutions. The high corrosion resistance of this alloy in corrosive solutions leads to the formation of Fe-, Cr- and Mo-enriched protective thin surface films.

  14. Adsorption of nicotine on different zeolite types, from aqueous solutions

    Directory of Open Access Journals (Sweden)

    Stošić Dušan K.

    2007-01-01

    Full Text Available The plant alkaloid, nicotine, is a strongly toxic heterocyclic compound: the lethal dose for an adult human being (40-60 mg is importantly lower in comparison with the other known poisons such as arsenic or strychni­ne. Cigarettes represent "the most toxic and addictive form of nicotine". Besides the negative effects of nicotine on public health produced by self-administration, recently another potentially very dangerous effect has been recognized: because of its miscibility with water, nicotine can be found in industrial wastewaters, and consequently, in groundwater. Therefore, the problem of nicotine removal from aqueous solutions has became an interesting topic. In this work, the removal of nicotine has been probed by adsorption on solid materials. Adsorption of nicotine on different zeolites (clinoptilolite, ZSM-5 and β zeolite and on activated carbon was investigated from aqueous solutions, at 298 K. The obtained results are presented as adsorption isotherms: the amount of adsorbed nicotine as a function of equilibrium concentration. These data were obtained from the residual amount of nicotine in the aqueous phase, by the use of UV spectroscopy. The highest amounts of adsorbed nicotine was found for activated carbon and p zeolite (~ mmol·g-1. The attempt to modify the adsorption properties of ZSM-5 zeolite has been also done: ZSM-5 was modified by ion-exchange with VIII group metal (Cu2+ and Fe3+. In addition, the adsorption of nicotine on ZSM-5 zeolite with different Si/Al ratios has been done. It has been noticed that ion-exchange did not improve the adsorption possibilities, while the adsorption was importantly lower in the case of higher silicon content in ZMS-5 structure. 13C NMR spectra were collected for suspensions formed of solid adsorbent and aqueous solution of nicotine; in this way, the part of nicotine molecule which is most probably connected with the adsorbent was recognized.

  15. Depolarization of negative muons in water and aqueous solutions

    International Nuclear Information System (INIS)

    The dependence of negative muon depolarization on temperature and hydrogen peroxide concentration is measured in various aqueous solutions located in longitudinal or transverse magnetic fields. It is shown that the experimental data are mot inconsistent with the familiar concepts regarding the behaviour of free radicals in aqueous solutions. The residual polarization in pure water solution of hydrogen peroxide is found to 1.8 times higher than that in pure water. This is interpreted as being the result of chemical interaction between meso nitrogen and hydrogen peroxide molecules leading to the formation of diamagnetic compounds. It is shown that the degree of depolarization does not depend on the magnetic field strength. According to the depolarization model in which meso nitrogen chemical reactions are taken into account this signifies that the meso atom enters the chemical reactions during a time t≅10-11 sec. at T=300 K; the paramagnetic products of these primary reactions which contain meso nitrogen then participate in secondary reactions during a time t1≤10-7 sec. The rate constants of the reactions leading to the formation of diamagnetic products can be obtained by treating the concentration and temperature dependences of depolarization in an aqueous solution of hydrogen peroxide in accordance with the model assuming chemical reactions between the meso atom and H2O molecules. The order of magnitude of the constant k≅10-11 sec-1⋅sm3is the same as that of the constant for reactions between free H and OH radicals in water. The temperature dependences of depolarization in water and a water solution of hydrogen peroxide are same consistent with the concept that the meso nitrogen reactions are chemical reactions by diffusion. (author)

  16. The Gibbs-free-energy landscape for the solute association in nanoconfined aqueous solutions

    Institute of Scientific and Technical Information of China (English)

    赵亮; 王春雷; 方海平; 涂育松

    2015-01-01

    The theoretical model and the numerical analyses on the Gibbs-free-energy of the association states of am-phiphilic molecules in nanoconfined aqueous solutions are presented in detail. We exhibit the continuous change of the Gibbs-free-energy trend, which plays a critical role in the association states of the system transforming from the dispersion state, through the “reversible state”, and finally to the aggregation state in amphiphilic molecule solutions. Furthermore, for the“reversible state”, we present the difference in the free-energy bar-rier heights of the dispersion state and aggregation state, resulting from the competition between the entropy, which makes the solute molecules evenly disperse in the solution and the energy contribution driving the am-phiphilic molecules to aggregate into a larger cluster. These findings provide a comprehensive understanding of confinement effects on the solute association processes in aqueous solutions and may further improve the techniques of material fabrication.

  17. Inclusion complexation of novocaine by beta-cyclodextrin in aqueous solutions.

    Science.gov (United States)

    Iglesias, Emilia

    2006-06-01

    The formation of inclusion complexes between beta-cyclodextrin (beta-CD) and the local anesthetic 2-(diethylamino)ethyl-p-amino-benzoate (novocaine) in aqueous solutions under different acidity conditions, using steady-state fluorescence or UV-vis spectroscopies, electrical conductivity, or the kinetic study of both the nitrosation reaction of the primary amine group in a mild acid medium and the hydrolysis of the ester function under an alkaline medium, has been studied. The inclusion complex formation between neutral or protonated novocaine and beta-CD of 1:1 stoichiometry was observed; however, the magnitude of the binding constants depends on the nature of both the guest and the host, and the higher-affinity guest-host was found under conditions when both the novocaine and the beta-CD were neutral molecules.

  18. Reaction mechanism studies on isoquinoline with hydroxyl radical in aqueous solutions

    Institute of Scientific and Technical Information of China (English)

    ZHU Dazhang; WANG Shilong; SUN Xiaoyu; NI Yarning; YAO Side

    2007-01-01

    The reaction mechanism between isoquinoline and .OH radical in aqueous dilute solutions under different conditions was studied by pulse radiolysis. The main chara-cteristic peaks in these transient absorption spectra were attributed and the growth-decay trends of several transient species were investigated. Under neutral or alkaline condi-tions, the reaction of-OH radical and isoquinoline produces OH-adducts with respective rate constants of 3.4 × 109 and 6.6× 109 mol-1.dm3·s-1 while under acidic conditions, the isoquinoline was firstly protonated and then -OH added to the benzene ring and produced protonated isoquinoline OH-adducts with a rate constant of 3.9× 109 mol-1.dm3·s-1.With a better understanding on radiolysis ofisoquinoline, this study is of help for its degradation and for environmental protection.

  19. Aqueous Solutions on Silica Surfaces: Structure and Dynamics from Simulations

    Science.gov (United States)

    Striolo, Alberto; Argyris, Dimitrios; Tummala, Naga Rajesh

    2009-03-01

    Our group is interested in understanding the properties of aqueous electrolyte solutions at interfaces. The fundamental questions we seek to answer include: (A) how does a solid structure perturb interfacial water? (B) How far from the solid does this perturbation persist? (C) What is the rate of water reorientation and exchange in the perturbed layer? (D) What happens in the presence of simple electrolytes? To address such topics we implemented atomistic molecular dynamics simulations. Recent results for water and simple electrolytes near silicon dioxide surfaces of various degrees of hydroxylation will be presented. The data suggest the formation of a layered aqueous structure near the interface. The density profile of interfacial water seems to dictate the density profiles of aqueous solutions containing NaCl, CaCl2, CsCl, and SrCl2 near the solid surfaces. These results suggest that ion-ion and ion-water correlations are extremely important factors that should be considered when it is desired to predict the distribution of electrolytes near a charged surface. Our results will benefit a number of practical applications including water desalination, exploitation of the oil shale in the Green River Basin, nuclear waste sites remediation, and design of nanofluidic devices.

  20. RHEOLOGICAL BEHAVIOR OF ERWINIA GUM IN AQUEOUS SOLUTION

    Institute of Scientific and Technical Information of China (English)

    Li-na Zhang; Mei Zhang; Jing-hua Chen; Hideki Iijima; Hiromichi Tsuchiya

    1999-01-01

    Erwinia (E) gum, an extracellular polysaccharide, is composed of fucose, galatose, glucose and glucuronic acid. Its viscosity behavior was investigated by a low-shear-rate multiball viscometer and a rotational viscometer. Its weight-average molecular weight Mw and intrinsic viscosity [η] in 0.2 mol/L NaCl aqueous solution were measured by light scattering method at 35℃ and viscometry at 25℃ and found to be 1.06 × 106 g/mol and 1050 mL/g, respectively, and its aggregates in aqueous solution were proved by gel permeation chromatography (GPC). These results indicated that E gum in water has exceedingly high viscosity and exhibits Binham fluid behavior, owing to its aggregation. The viscosity of E gum decreased with increasing temperature, and the turning point appeared at 38℃ for dilute solution and 80℃ for concentrated solution suggesting that the aggregates of E gum in water started to disaggregate under these temperatures. In addition, the aggregates can be disrupted by adding either acid or base. The experimental results indicated that the E gum is a good thickening agent, and its fluid behavior is similar to xanthan.

  1. An electrochemical treatment for aqueous radioactive solutions using pottery

    International Nuclear Information System (INIS)

    A bench scale electrolytic cell made from plexiglas was used for electrochemical separation of 137Cs and 60Co from simullated aqueous radioactive solutions. In this cell, a stainless steel plate represented the anode. The electrochemical treatment technique used depends on forcing the radioactive cations of the solution (137Cs+ and 60Co++) towards the opposite electrode under the influence of applied electric current, where they highly sorbed in the pottery body. The highest removal for137Cs+ and 60Co was in the alkalina medium, especially at pH>9. The investigated factors affected the electrochemicla processes are, applied voltage, treatment duration, hydrogen ion concentration of the radioactive solution, and the consumed electrical energy . It was found that at pH 11, applied voltage 30V and current 100 mA, the highest removal of 137Cs is 99.8% after 2.5 hours, and 99.3% and 99.3% for 60Co after 1.25 hour.The total consumed energy for 137Cs and 60Co were 33.75 and 16.88 W.h.dm-3, respectively. Comparing with other treatment methods, the electrochemical method revealed three advantages: shorter treatment time, low-cost materials, and low consumed energy. The results obtained showed that the dual application of electric current and sorption on the surface of pottery are feasible for the treatment of aqueous radioactive solutions

  2. Aqueous solution of basic fuchsin as food irradiation dosimeter

    International Nuclear Information System (INIS)

    Dosimetric characterization of aqueous solution of basic fuchsin has been studied spectrophotometrically for the possible application in the low-dose food irradiation dosimetry. Absorption spectra of unirradiated and irradiated solutions were determined and decrease in the absorption with the radiation dose was noted down. Radiation-induced bleaching of the dye was measured at wavelengths of maximum absorption λmax (540nm) as well as 510, 460 and 400 nm wavelengths. At all these wavelengths, the decrease in the absorbance of the dosimeter was linear with respect to the absorbed dose from 0.05 to 0.6 kGy. The stability of dosimetric solution during the post-irradiation storage in the dark at room temperature showed that after initial bleaching during first eight days, the response was almost stable for about 34 days. The effect of different light and temperature conditions also showed that the response gradually decreased during the storage period of 34 days, which shows that the basic fuchsin dye is photosensitive as well as thermally sensitive. The possibility of using aqueous solution of basic fuchsin as food irradiation dosimeter will be discussed. (authors)

  3. Nano particles@Calix arenas via aqueous solution

    Directory of Open Access Journals (Sweden)

    Sahar Dehghani

    2016-05-01

    Full Text Available The electronic structure and magnetic properties of Al2O3, GaN and Fe3O4@ Calix (8 COOH have been studied using ONIOM and DFT methods. The studies focus on how to improve the adsorption of some nano particles solution aqueous for achieving good magnetic and functionalized potential performances. The results revealed that the Fe3O4@ Calix (8 COOH and some of its derivations exhibited better thermodynamic stability. Furthermore, the particle size and magnetic property of the GaN@ Calix (8 COOH nano particles can be controlled by the aqueous. The electrical properties such as NMR Shielding, electron densities, energy densities, potential energy densities, ELF, LOL, ellipticity of electron density, eta index and ECP for nano particles@ Calix (8COOH have been calculated.

  4. Wash Solution Bath Life Extension for the Space Shuttle Rocket Motor Aqueous Cleaning System

    Science.gov (United States)

    Saunders, Chad; Evans, Kurt; Sagers, Neil

    1999-01-01

    A spray-in-air aqueous cleaning system, which replaced 1,1,1 trichloroethane (TCA) vapor degreasing, is used for critical cleaning of Space Shuttle Redesigned Solid Rocket Motor (RSRM) metal parts. Small-scale testing demonstrated that the alkaline-based wash solution possesses adequate soil loading and cleaning properties. However, full-scale testing exhibited unexpected depletion of some primary components of the wash solution. Specifically, there was a significant decrease in the concentration of sodium metasilicate which forced change-out of the wash solution after eight days. Extension of wash solution bath life was necessary to ease the burden of frequent change-out on manufacturing. A laboratory study supports a depletion mechanism that is initiated by the hydrolysis of sodium tripolyphosphate (STPP) lowering the pH of the solution. The decrease in pH causes polymerization and subsequent precipitation of sodium metasilicate (SM). Further investigation showed that maintaining the pH was the key to preventing the precipitation of the sodium metasilicate. Implementation to the full scale operation demonstrated that periodic additions of potassium hydroxide (KOH) extended the useful bath life to more than four months.

  5. Magnetic composite nanofibers fabricated by electrospinning of Fe3O4/gelatin aqueous solutions

    International Nuclear Information System (INIS)

    Graphical abstract: Superparamagnetic Fe3O4/GE composite nanofibers with saturation magnetization of 12.87 emμ g−1 were prepared from gelatin aqueous solution at an elevated temperature by electrospinning. - Highlights: • Electrospinning GE aqueous solution at higher temperature. • Presenting a simple and effective technique, combining wet blending with high temperature electrospinning to prepare magnetic composite nanofibers. • Developing composite nanofibers with higher superparamagnetic properties is expected to be useful in application for the biomedical field. - Abstract: We have fabricated magnetic composite nanofibers containing superparamagnetic Fe3O4 nanoparticles by the electrospinning method. Highly dispersed Fe3O4 magnetic nanoparticles were synthesized by one-step co-precipitation of Fe2+/Fe3+ under an alkaline condition with 4 wt% poly(vinyl alcohol) (PVA) aqueous solution as the stabilizer. Gelatin (GE) was used as a polymeric matrix for fabricating the nanocomposites. The prepared Fe3O4/GE composite nanofibers were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD), respectively. These composite nanofibers show uniform and continuous morphology with the Fe3O4 nanoparticles embedded in the nanofibers. By studying the magnetic properties of the Fe3O4/GE composite nanofibers, we confirm that the composite nanofibers possess superparamagnetic properties with a high saturated magnetization (Ms = 12.87 emμ g−1) at room temperature. The features of this approach for getting one-dimensional magnetic nanostructure are its simplicity, effectiveness and safety. The Fe3O4/GE nanofibers with superparamagnetic properties would be potentially applied in biomedical field

  6. Bioprecipitation of uranium from alkaline waste solutions using recombinant Deinococcus radiodurans

    Energy Technology Data Exchange (ETDEWEB)

    Kulkarni, Sayali; Ballal, Anand; Apte, Shree Kumar, E-mail: aptesk@barc.gov.in

    2013-11-15

    Highlights: • Deinococcus radiodurans was genetically engineered to overexpress alkaline phosphatase (PhoK). • Deino-PhoK bioprecipitated U efficiently over a wide range of input U concentration. • A maximal loading of 10.7 g U/g of biomass at 10 mM input U was observed. • Radioresistance and U precipitation by Deino-PhoK remained unaffected by γ radiation. • Immobilization of Deino-PhoK facilitated easy separation of precipitated U. -- Abstract: Bioremediation of uranium (U) from alkaline waste solutions remains inadequately explored. We engineered the phoK gene (encoding a novel alkaline phosphatase, PhoK) from Sphingomonas sp. for overexpression in the radioresistant bacterium Deinococcus radiodurans. The recombinant strain thus obtained (Deino-PhoK) exhibited remarkably high alkaline phosphatase activity as evidenced by zymographic and enzyme activity assays. Deino-PhoK cells could efficiently precipitate uranium over a wide range of input U concentrations. At low uranyl concentrations (1 mM), the strain precipitated >90% of uranium within 2 h while a high loading capacity of around 10.7 g U/g of dry weight of cells was achieved at 10 mM U concentration. Uranium bioprecipitation by Deino-PhoK cells was not affected in the presence of Cs and Sr, commonly present in intermediate and low level liquid radioactive waste, or after exposure to very high doses of ionizing radiation. Transmission electron micrographs revealed the extracellular nature of bioprecipitated U, while X-ray diffraction and fluorescence analysis identified the precipitated uranyl phosphate species as chernikovite. When immobilized into calcium alginate beads, Deino-PhoK cells efficiently removed uranium, which remained trapped in beads, thus accomplishing physical separation of precipitated uranyl phosphate from solutions. The data demonstrate superior ability of Deino-PhoK, over earlier reported strains, in removal of uranium from alkaline solutions and its potential use in

  7. Boron removal from aqueous solution by direct contact membrane distillation

    International Nuclear Information System (INIS)

    The removal of boron from aqueous solution by direct contact membrane distillation (DCMD) was studied with self-prepared polyvinylidene fluoride (PVDF) hollow fiber membranes in the present work. The effect of pH, boron concentration, temperature and salt concentration of the feed solution on the boron rejection was investigated. The experimental results indicated that boron rejection was less dependent on the feed pH and salt concentration. DCMD process had high boron removal efficiency (>99.8%) and the permeate boron was below the maximum permissible level even at feed concentration as high as 750 mg/L. Although the permeate flux was enhanced exponentially with the feed temperature increasing, the influence of feed temperature on the boron rejection could be neglected. Finally, the natural groundwater sample containing 12.7 mg/L of boron was treated by DCMD process. The permeate boron kept below 20 μg/L whether the feed was acidified or not, but pre-acidification was helpful to maintain the permeate flux stability. All the experimental results indicated that DCMD could be efficiently used for boron removal from aqueous solution.

  8. Removal of Cholera Toxin from Aqueous Solution by Probiotic Bacteria

    Directory of Open Access Journals (Sweden)

    Jussi A. O. Meriluoto

    2012-06-01

    Full Text Available Cholera remains a serious health problem, especially in developing countries where basic hygiene standards are not met. The symptoms of cholera are caused by cholera toxin, an enterotoxin, which is produced by the bacterium Vibrio cholerae. We have recently shown that human probiotic bacteria are capable of removing cyanobacterial toxins from aqueous solutions. In the present study we investigate the ability of the human probiotic bacteria, Lactobacillus rhamnosus strain GG (ATCC 53103 and Bifidobacterium longum 46 (DSM 14583, to remove cholera toxin from solution in vitro. Lactobacillus rhamnosus strain GG and Bifidobacterium longum 46 were able to remove 68% and 59% of cholera toxin from aqueous solutions during 18 h of incubation at 37 °C, respectively. The effect was dependent on bacterial concentration and L. rhamnosus GG was more effective at lower bacterial concentrations. No significant effect on cholera toxin concentration was observed when nonviable bacteria or bacterial supernatant was used.

  9. Preparation of fluorescent polyaniline nanoparticles in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Alves, Kleber G. B. [Universidade Federal de Pernambuco, Departamento de Engenharia Mecanica (Brazil); Melo, Etelino F. de [Universidade Federal de Pernambuco, Departamento de Quimica Fundamental (Brazil); Andrade, Cesar A. S. [Universidade Federal de Pernambuco, Departamento de Bioquimica (Brazil); Melo, Celso P. de, E-mail: celso@df.ufpe.br [Universidade Federal de Pernambuco, Departamento de Fisica (Brazil)

    2013-01-15

    We report the synthesis of stable polyaniline nanoparticles (PANI{sub N}Ps) based on the chemical oxidative polymerization of aniline in aqueous solutions of surfactants. Surfactants of three different types-cationic (dodecyltrimethylammonium bromide-DTAB), anionic (sodium dodecyl sulfate-SDS), and non-ionic (Triton X-405-TX-405)-were used. The resulting PANI{sub N}Ps{sub s}urfactant samples were characterized through UV-Vis, fluorescence and Fourier transform infrared spectroscopies, and scanning electronic microscopy (SEM). We have verified that the color of the PANI{sub N}Ps{sub s}urfactant dispersions is affected by a change in the pH of the solution. The PANI-NPs{sub s}urfactant colloidal suspensions in aqueous solution present a surprising high fluorescence quantum yield value (ranging from 1.9 Multiplication-Sign 10{sup -3} to 6.9 Multiplication-Sign 10{sup -3}) that can be controlled as a function of the pH, a fact that we associate to the corresponding protonation degree of the PANI polymeric chains. We suggest that these fluorescent nanocomposites can find important technological applications in different areas such as organic light emitting devices, biosensors, and pigments for coatings.

  10. Removing Phosphorus from Aqueous Solutions Using Lanthanum Modified Pine Needles.

    Directory of Open Access Journals (Sweden)

    Xianze Wang

    Full Text Available The renewable pine needles was used as an adsorbent to remove phosphorus from aqueous solutions. Using batch experiments, pine needles pretreated with alkali-isopropanol (AI failed to effectively remove phosphorus, while pine needles modified with lanthanum hydroxide (LH showed relatively high removal efficiency. LH pine needles were effective at a wide pH ranges, with the highest removal efficiency reaching approximately 85% at a pH of 3. The removal efficiency was kept above 65% using 10 mg/L phosphorus solutions at desired pH values. There was no apparent significant competitive behavior between co-existing anions of sulfate, nitrate, and chloride (SO4(2-, NO3(- and Cl(-; however, CO3(2- exhibited increased interfering behavior as concentrations increased. An intraparticle diffusion model showed that the adsorption process occurred in three phases, suggesting that a boundary layer adsorption phenomena slightly affected the adsorption process, and that intraparticle diffusion was dominant. The adsorption process was thermodynamically unfavorable and non-spontaneous; temperature increases improved phosphorus removal. Total organic carbon (TOC assays indicated that chemical modification reduced the release of soluble organic compounds from 135.6 mg/L to 7.76 mg/L. This new information about adsorption performances provides valuable information, and can inform future technological applications designed to remove phosphorus from aqueous solutions.

  11. Removing Phosphorus from Aqueous Solutions Using Lanthanum Modified Pine Needles

    Science.gov (United States)

    Wang, Xianze; Liu, Zhongmou; Liu, Jiancong; Huo, Mingxin; Huo, Hongliang; Yang, Wu

    2015-01-01

    The renewable pine needles was used as an adsorbent to remove phosphorus from aqueous solutions. Using batch experiments, pine needles pretreated with alkali-isopropanol (AI) failed to effectively remove phosphorus, while pine needles modified with lanthanum hydroxide (LH) showed relatively high removal efficiency. LH pine needles were effective at a wide pH ranges, with the highest removal efficiency reaching approximately 85% at a pH of 3. The removal efficiency was kept above 65% using 10 mg/L phosphorus solutions at desired pH values. There was no apparent significant competitive behavior between co-existing anions of sulfate, nitrate, and chloride (SO42-, NO3- and Cl-); however, CO32- exhibited increased interfering behavior as concentrations increased. An intraparticle diffusion model showed that the adsorption process occurred in three phases, suggesting that a boundary layer adsorption phenomena slightly affected the adsorption process, and that intraparticle diffusion was dominant. The adsorption process was thermodynamically unfavorable and non-spontaneous; temperature increases improved phosphorus removal. Total organic carbon (TOC) assays indicated that chemical modification reduced the release of soluble organic compounds from 135.6 mg/L to 7.76 mg/L. This new information about adsorption performances provides valuable information, and can inform future technological applications designed to remove phosphorus from aqueous solutions. PMID:26630014

  12. Qualitative and quantitative analysis of beta emitters in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Hamzah, Zaini bin

    1983-01-01

    A beta spectrometer, consisting of a liquid scintillation counter, coupled to a programmable multichannel analyser was used to achieve the objective of detecting and measuring beta activity in low level aqueous environmental solution as well as identifying the radioisotopes present. Aqueous solutions of standard beta emitters, covering a range of energies between 18.6 KeV and 3550 KeV, were used to develop computer methods for analysis. The effects of pH, acids, bases, buffers, and salts on the stability of the mixture and on the detection efficiency of the radioisotopes, were investigated. It was found that temperature changes, beyond the operating temperature range, could result in severe errors. Application of the Cherenkov counting technique for beta emitters, gives extra data to support the main results. For the analysis of environmental solutions, which may contain a variety of radioisotopes, the system was used to obtain spectra of alpha emitters, beta emitters with internal conversion and Cherenkov radiation. Synthetic mixtures of tritium and carbon-14 of activity ratios between 8:1 and 1:8 were used to investigate the problems of multielement spectral analysis.

  13. NMR studies of proton exchange kinetics in aqueous formaldehyde solutions

    Science.gov (United States)

    Rivlin, Michal; Eliav, Uzi; Navon, Gil

    2014-05-01

    Aqueous solutions of formaldehyde, formalin, are commonly used for tissue fixation and preservation. Treatment with formalin is known to shorten the tissue transverse relaxation time T2. Part of this shortening is due to the effect of formalin on the water T2. In the present work we show that the shortening of water T2 is a result of proton exchange between water and the major constituent of aqueous solutions of formaldehyde, methylene glycol. We report the observation of the signal of the hydroxyl protons of methylene glycol at 2 ppm to high frequency of the water signal that can be seen at low temperatures and at pH range of 6.0 ± 1.5 and, at conditions where it cannot be observed by the single pulse experiment, it can be detected indirectly through the water signal by the chemical exchange saturation transfer (CEST) experiment. The above finding made it possible to obtain the exchange rate between the hydroxyl protons of the methylene glycol and water in aqueous formaldehyde solutions, either using the dispersion of the spin-lattice relaxation rate in the rotating frame (1/T1ρ) or, at the slow exchange regime, from the line width hydroxyl protons of methylene glycol. The exchange rate was ∼104 s-1 at pH 7.4 and 37 °C, the activation energy, 50.2 kJ/mol and its pH dependence at 1.1 °C was fitted to: k (s-1) = 520 + 6.5 × 107[H+] + 3.0 × 109[OH-].

  14. Transformations of polyols to organic acids and hydrogen in aqueous alkaline media

    NARCIS (Netherlands)

    Haasterecht, van T.; Deelen, van T.W.; Jong, de K.P.; Bitter, J.H.

    2014-01-01

    In this paper we show that carbon nanofiber supported copper and nickel nanoparticles can selectively transform ethylene glycol and glycerol into value added oxygenates (organic acids) under anaerobic aqueous conditions. During aqueous phase oxidation Cu based catalysts showed a nearly quantitative

  15. Removal of heavy metals from aqueous solutions using opalized tuff

    OpenAIRE

    Golomeova, Mirjana; Zendelska, Afrodita; Golomeov, Blagoj; Krstev, Boris; Jakupi, Shaban

    2015-01-01

    This paper presents the results of the examination of the possibility of applying opalized tuff as a natural raw material for disposal of heavy metals (copper, zinc, manganese and lead) from aqueous solutions. Of actual experiments obtained results show that working conditions attaching to the removal of Cu and Pb ions is more than 91% of zinc ions is above 81%, while manganese ions are removed about 77% .On this can be concluded that the removal of examined heavy metals using opalized tuff i...

  16. Degradation of Sodium-Polyacrylate in Dilute Aqueous Solution

    Science.gov (United States)

    Saita, Takao

    1980-12-01

    It is shown using a capillary viscometer that the viscosity of a dilute aqueous solution of sodium-polyacrylate at 20°C decreases gradually for each flow time measurement and also decreases with the time of rest. Assuming that the polymer degradation is caused by shearing stress and oxidation, their effects are discussed with the data obtained using a closed-type capillary viscometer derived for this investigation. It is proved from the results that rupture of the Na-PAA molecule is caused by mechanochemical degradation, and also photo-degradation under the usual illumination and sunlight in a laboratory.

  17. Fluorescence of aqueous solutions of commercial humic products

    Science.gov (United States)

    Gosteva, O. Yu.; Izosimov, A. A.; Patsaeva, S. V.; Yuzhakov, V. I.; Yakimenko, O. S.

    2012-01-01

    We have studied the spectral luminescence characteristics of aqueous solutions of humic products obtained from different raw material sources, and their behavior as the excitation wavelength increases from 270 nm to 355 nm. We have identified differences in the spectral properties of industrial humic products from coalified materials, lignin-containing organic waste, and humic products from plant raw material (peat, sapropel, vermicompost). We have shown that humic products from plant raw material have spectral properties closer to those for humic substances in natural water or soil than humic products from coalified materials.

  18. Hydrate-based heavy metal separation from aqueous solution

    Science.gov (United States)

    Song, Yongchen; Dong, Hongsheng; Yang, Lei; Yang, Mingjun; Li, Yanghui; Ling, Zheng; Zhao, Jiafei

    2016-02-01

    A novel hydrate-based method is proposed for separating heavy metal ions from aqueous solution. We report the first batch of experiments and removal characteristics in this paper, the effectiveness and feasibility of which are verified by Raman spectroscopy analysis and cross-experiment. 88.01-90.82% of removal efficiencies for Cr3+, Cu2+, Ni2+, and Zn2+ were obtained. Further study showed that higher R141b-effluent volume ratio contributed to higher enrichment factor and yield of dissociated water, while lower R141b-effluent volume ratio resulted in higher removal efficiency. This study provides insights into low-energy, intensive treatment of wastewater.

  19. ADSORPTION OF METHYLENE BLUE FROM AQUEOUS SOLUTION ON ATTAPULGITE

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Batch adsorption experiments were carried out for the removal of methylene blue (MB) from aqueous solution using attapulgite as adsorbent. The effects of various parameters such as temperature, contact time, the pH value, and attapulgite dosage on the adsorption performance were investigated. The standard curve and regression equation were established by spectrophotometry. The adsorption experimental results showed that the adsorption equilibrium data were well in accord with Langmuir adsorptive model. The optimal result was acquired under the experimental condition of attapulgite dosage 0.18g, MB concentration 50.0mg/L, pH 10, and adsorption time 20min at room temperature.

  20. Nano particles@Calix arenas via aqueous solution

    OpenAIRE

    Sahar Dehghani

    2016-01-01

    The electronic structure and magnetic properties of Al2O3, GaN and Fe3O4@ Calix (8) COOH have been studied using ONIOM and DFT methods. The studies focus on how to improve the adsorption of some nano particles solution aqueous for achieving good magnetic and functionalized potential performances. The results revealed that the Fe3O4@ Calix (8) COOH and some of its derivations exhibited better thermodynamic stability. Furthermore, the particle size and magnetic property of the GaN@ Calix (8) C...

  1. Strong adhesion and cohesion of chitosan in aqueous solutions

    OpenAIRE

    Lee, DW; Lim, C. (Cheryl); Israelachvili, JN; Hwang, DS

    2013-01-01

    Chitosan, a load-bearing biomacromolecule found in the exoskeletons of crustaceans and insects, is a promising biopolymer for the replacement of synthetic plastic compounds. Here, surface interactions mediated by chitosan in aqueous solutions, including the effects of pH and contact time, were investigated using a surface forces apparatus (SFA). Chitosan films showed an adhesion to mica for all tested pH ranges (3.0-8.5), achieving a maximum value at pH 3.0 after a contact time of 1 h (Wad ∼ ...

  2. Standard Electrode Potentials Involving Radicals in Aqueous Solution: Inorganic Radicals

    Energy Technology Data Exchange (ETDEWEB)

    Armstrong, David A.; Huie, Robert E.; Koppenol, Willem H.; Lymar, Sergei V.; Merenyi, Gabor; Neta, Pedatsur; Ruscic, Branko; Stanbury, David M.; Steenken, Steen; Wardman, Peter

    2015-12-01

    Recommendations are made for standard potentials involving select inorganic radicals in aqueous solution at 25 °C. These recommendations are based on a critical and thorough literature review and also by performing derivations from various literature reports. The recommended data are summarized in tables of standard potentials, Gibbs energies of formation, radical pKa’s, and hemicolligation equilibrium constants. In all cases, current best estimates of the uncertainties are provided. An extensive set of Data Sheets is appended that provide original literature references, summarize the experimental results, and describe the decisions and procedures leading to each of the recommendations

  3. The characterization methods for colloids in aqueous solutions

    International Nuclear Information System (INIS)

    This literature review deals with characterization methods for colloids in aqueous solutions and in groundwater. The basis for the review has been the needs of nuclear waste disposal studies and methods applicable in such studies. The methods considered include non-destructive laserspectroscopic methods (e.g. TRLFS, LPAS, PALS), several separation methods (e.g. ultrafiltration, dialysis, electrophoresis, field-flow-fractionation) and also some surface analytical methods, as well as some other methods giving additional information on formation and migration properties of colloids. (au.) (71 refs., 13 figs., 3 tabs.)

  4. Removal of phenols from aqueous solutions by emulsion liquid membranes.

    Science.gov (United States)

    Reis, M Teresa A; Freitas, Ondina M F; Agarwal, Shiva; Ferreira, Licínio M; Ismael, M Rosinda C; Machado, Remígio; Carvalho, Jorge M R

    2011-09-15

    The present study deals with the extraction of phenols from aqueous solutions by using the emulsion liquid membranes technique. Besides phenol, two derivatives of phenol, i.e., tyrosol (2-(4-hydroxyphenyl)ethanol) and p-coumaric acid (4-hydroxycinnamic acid), which are typical components of the effluents produced in olive oil plants, were selected as the target solutes. The effect of the composition of the organic phase on the removal of solutes was examined. The influence of pH of feed phase on the extraction of tyrosol and p-coumaric was tested for the membrane with Cyanex 923 as an extractant. The use of 2% Cyanex 923 allowed obtaining a very high extraction of phenols (97-99%) in 5-6 min of contact time for either single solute solutions or for their mixtures. The removal efficiency of phenol and p-coumaric acid attained equivalent values by using the system with 2% isodecanol, but the removal rate of tyrosol was found greatly reduced. The extraction of tyrosol and p-coumaric acid from their binary mixture was also analysed for different operating conditions like the volume ratio of feed phase to stripping phase (sodium hydroxide), the temperature and the initial concentration of solute in the feed phase.

  5. Characterization of Laboratory Prepared Concrete Pastes Exposed to High Alkaline and High Sodium Salt Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Langton, C. A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2016-06-30

    The objective of this study was to identify potential chemical degradation mechanisms for the Saltstone Disposal Unit (SDU) concretes, which over the performance life of the structures may be exposed to highly alkaline sodium salt solutions containing sulfate, hydroxide, and other potentially corrosive chemicals in salt solution and saltstone flush water, drain water, leachate and / or pore solution. The samples analyzed in this study were cement pastes prepared in the SIMCO Technologies, Inc. concrete laboratory. They were based on the paste fractions of the concretes used to construct the Saltstone Disposal Units (SDUs). SDU 1 and 4 concrete pastes were represented by the PV1 test specimens. The paste in the SDU 2, 3, 5, and 6 concrete was represented by the PV2 test specimens. SIMCO Technologies, Inc. selected the chemicals and proportions in the aggressive solutions to approximate proportions in the saltstone pore solution [2, 3, 5, and 6]. These test specimens were cured for 56 days in curing chamber before being immersed in aggressive solutions. After exposure, the samples were frozen to prevent additional chemical transport and reaction. Selected archived (retrieved from the freezer) samples were sent to the Savannah River National Laboratory (SRNL) for additional characterization using x-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive x-ray (EDX) spectroscopy. Characterization results are summarized in this report. In addition, a correlation between the oxide composition of the pastes and their chemical durability in the alkaline salt solutions is provided.

  6. Temperature dependence of the absorbance of alkaline solutions of 4-nitrophenyl phosphate--a potential source of error in the measurement of alkaline phosphatase activity.

    Science.gov (United States)

    Burtis, C A; Seibert, L E; Baird, M A; Sampson, E J

    1977-09-01

    The absorbance of an alkaline solution of 4-nitrophenyl phosphate is a function of temperature. Quantitative evaluation of this phenomenon indicates that it (a) depends on the concentration of the compound and is independent of source, buffer concentration, and pH above 9.0; (b) is reversible; (c) is not a result of alkaline hydrolysis or 4-nitrophenol contamination; and (d) correlates with a temperature-induced shift of its absorbance spectrum. The phenomenon may represent a potential analytical problem in methods for alkaline phosphatase in which this compound is the substrate. If thermal equilibrium is not reached and maintained during an alkaline phosphatase assay, the thermochromic response will be included in the measured rate. The magnitude of this error depends on the thermal response and control characteristics of each particular instrument and the reaction conditions under which such an analysis is performed. PMID:19164

  7. Bifunctional, Carbon-Free Nickel/Cobalt-Oxide Cathodes for Lithium-Air Batteries with an Aqueous Alkaline Electrolyte

    International Nuclear Information System (INIS)

    Highlights: • High activity bi-functional catalyst combination for ORR and OER . • An optimum ratio of high active bi-functional catalysts was found. • Novel electrodes without carbon to avoid carbon corrosion during OER mode. • EIS model for OER describes influence of a growing oxide layers. • Long-term test exhibited an excellent long-term stability over 1200 cycles. - Abstract: Lithium-air batteries with an aqueous alkaline electrolyte promise a very high practical energy density and capacity. These batteries are mainly limited by high overpotentials on the bifunctional cathode during charge and discharge. To reduce overpotentials the bifunctional cathode of such batteries must be improved significantly. Nickel is relatively inexpensive and has a good catalytic activity in alkaline media. Co3O4 was found to be a promising metal oxide catalyst for oxygen evolution in alkaline media but it has a low electronic conductivity. On the other hand since nickel has a good electronic conductivity Co3O4 can be added to pure nickel electrodes to enhance performance due to a synergetic effect. Due to the poor stability of carbon materials at high anodic potentials, gas diffusion electrodes were prepared without carbon to improve especially long-term stability. Gas diffusion electrodes were electrochemically investigated in a half cell. In addition, cyclic voltammogrametry (CV) and electrochemical impedance spectroscopy (EIS) were carried out. SEM was used for the physical and morphological investigations. Investigations showed that electrodes containing 20 wt.% Co3O4 exhibited the highest performance

  8. Thermodynamic, kinetic and mechanistic investigations of Piperazine oxidation by Diperiodatocuprate(III) complex in aqueous alkaline medium

    Indian Academy of Sciences (India)

    Vijay P Pattar; Prashant A Magdum; Deepa G Patil; Sharanappa T Nandibewoor

    2016-03-01

    The kinetics of oxidation of piperazine by the copper complex, diperiodatocuprate(III) in alkaline medium was studied at 298 K, at an ionic strength of 2.0*10-2 mol dm-3. The reaction between piperazine and diperiodatocuprate(III) in aqueous alkaline medium exhibited 1:2 stoichiometry. The oxidation products were identified by UV-Visible, GC-MS and IR spectral studies. In the present study we have obtained different kinetic observations. The reaction exhibited unit order in case of diperiodatocuprate(III), while less than unit order with respect to piperazine. The addition of alkali and periodate retarded the rate of reaction. The effects of added products, ionic strength and dielectric constant on the rate of the reaction were also studied. The active species of diperiodatocuprate(III) in alkaline media is [Cu(OH)2(H3IO6)]-. The activation parameters with respect to the rate determining step and the thermodynamic quantities with respect to the equilibrium steps were evaluated and discussed. The plausible mechanism consistent with the experimental results was proposed and discussed in detail.

  9. Regeneration of Aqueous Periodate Solutions by Ozone Treatment: A Sustainable Approach for Dialdehyde Cellulose Production.

    Science.gov (United States)

    Koprivica, Slavica; Siller, Martin; Hosoya, Takashi; Roggenstein, Walter; Rosenau, Thomas; Potthast, Antje

    2016-04-21

    A method for easy and fast regeneration of aqueous periodate solutions from dialdehyde cellulose (DAC) production by ozone treatment is presented, along with a direct and reliable simultaneous quantification of iodate and periodate by reversed-phase HPLC. The influence of iodate and ozone concentration, solution pH, and reaction time on the regeneration efficiency was studied, as well as the reaction kinetics. Regeneration of spent periodate solutions by ozone was successfully performed in alkaline medium, which favors the formation of free (.) OH radicals, as supported by the addition of radical scavengers and quantum mechanical calculations. At pH 13 and an ozone concentration of approximately 150 mg L(-1) , periodate was completely regenerated from a 100 mm solution of iodate within 1 h at room temperature. A cyclic process of cellulose oxidation and subsequent regeneration of spent periodate with 90 % efficiency has been developed. So far, commercial applications of DAC have been hampered by difficulties in reusing the costly periodate. This work overcomes this hurdle and presents a highly efficient, clean, and low-cost protocol for the preparation of DAC with integrated periodate recycling, with the possibility of scaling the process up.

  10. Electrochemical Characterization of New Silver Gas Diffusion Electrodes during Oxygen Reduction in Alkaline Solution

    OpenAIRE

    Wagner, Norbert

    2013-01-01

    In order to analyze in detail the kinetics of the oxygen reduction reaction (ORR) and the influence of the porous electrode structure on the electrode performance in alkaline solution (10 M NaOH) at 80°C electrochemical impedance measurements (EIS) and cyclic voltammograms (CV) have been performed. The investigated electrodes were technical silver gas diffusion electrodes (GDE) and porous silver membranes with different pore radii ranging from 0.2 µm to 5 µm. Silver gas diffusion electrodes w...

  11. Removal of radioruthenium from alkaline intermediate level radioactive waste solution : a laboratory investigation

    International Nuclear Information System (INIS)

    Various methods were investigated in the laboratory for the removal of radioruthenium from alkaline intermediate level radioactive waste solutions of reprocessing plant origin. The methods included batch equilibration with different ion exchangers and sorbents, column testing and chemical precipitation. A column method using zinc-activated carbon mixture and a chemical precipitation method using ferrous salt along with sodium sulphite were found to be promising for plant scale application. (author). 10 refs., 3 figs., 7 tabs

  12. Electrochemical Reduction of Oxygen on Multi-walled Carbon Nanotubes Electrode in Alkaline Solution

    Institute of Scientific and Technical Information of China (English)

    You Qun CHU; Chun An MA; Feng Ming ZHAO; Hui HUANG

    2004-01-01

    The multi-walled carbon nanotubes (MWNTs) electrode was constructed using poly- tetrafluoroethylene as binder, and the electrochemical reductive behavior of oxygen in alkaline solution was first examined on this electrode. Compared with other carbon materials, MWNTs show higher electrocatalytic activity, and the reversibility of O2 reduction reaction is greatly improved. The experiments reveal that the electrochemical reduction of O2 to HO2- is controlled by adsorption. The preliminary results illustrate the potential application of MWNTs in fuel cells.

  13. Rheological properties of aqueous solutions of biopolymeric hyaluronan

    Science.gov (United States)

    Szwajczak, Elzbieta

    2004-09-01

    Aqueous solutions of hyaluronic acid (hyaluronan, HA) were studied. The HA compound is a natural polysaccharide, bipolymer. It plays an important role in numerous biological processes as a component of the extracellular matrix, connective tissues and, especially, human and animal synovial joints. Natural and artificial solutions of the HA have demonstrated the viscoelastic nature. These properties are shown to be related to the microstructure parameters (bulk concentration, molecular weight) and external parameters (temperature, stress, shear rate). We emphasize the role of the flow properties of polymeric systems. It is found a liquid crystalline "order" can be "induced" during the material flow. The dynamic properties, such as the elastic shear modulus and viscous shear modulus, are given. These results are discussed in relation to the postulated function of hyaluronic acid in synovial joint and with respect to possibilities o their application in medicine and pharmacology.

  14. INTERACTION OF POLYVINYLPYRROLIDONE WITH METAL CHLORIDE AQUEOUS SOLUTIONS

    Institute of Scientific and Technical Information of China (English)

    Mohammad Saleem Khan; Khaista Gul; Najeeb Ur Rehman

    2004-01-01

    Interactions of polyvinylpyrrolidone (PVP) with metal chlorides (MgCl2, CaCl2, KC1 and BaC12) have been investigated by viscometric and spectrophotometric techniques in aqueous solutions. Intrinsic viscosity [η] of (PVP) has shown a discontinuity with varying concentration of metal chlorides. The decreasing order of effectiveness of cation is K1+>Ca2+> Mg2+> Ba2+ for poly(vinylpyrrolidone) solution. Changes in the absorption spectra of the cosolutes were observed in the presence of PVP in the lower limit of the UV-visible region i.e. 200-210 nm. These changes were attributed to interaction of PVP molecules with the cosolute molecules. As the concentration of the cosolute increased, a red shift in the peaks was observed, indicating an increase in interaction between PVP and cosolutes.

  15. Adsorption of thorium from aqueous solutions by perlite.

    Science.gov (United States)

    Talip, Z; Eral, M; Hiçsönmez, U

    2009-02-01

    The use of expanded perlite for the adsorption of thorium from aqueous solution by batch technique is presented. The effects of particle size, pH of the solution, initial thorium concentration, shaking time, V/m ratio and temperature were determined. It was found that the adsorption capacity increases by the increase in the pH of the suspensions. The rate of thorium adsorption on expanded perlite was observed to be fast in the first hour of the reaction time. Adsorption isotherms were expressed by Langmuir and Freundlich adsorption models and the adsorption experiments conducted at 30 +/- 1 degrees C showed that the adsorption isotherms correlated well with the Langmuir model. From the adsorption data, thermodynamic parameters such as DeltaG(o), DeltaH(o) and DeltaS(o) were calculated as a function of temperature.

  16. Radiolysis of berberine or palmatine in aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Marszalek, Milena [Institute of Applied Radiation Chemistry, Technical University of Lodz, Wroblewskiego 15, 93-590 Lodz (Poland); Wolszczak, Marian, E-mail: marianwo@mitr.p.lodz.p [Institute of Applied Radiation Chemistry, Technical University of Lodz, Wroblewskiego 15, 93-590 Lodz (Poland)

    2011-01-15

    The reactions of hydrated electron (e{sub aq}{sup -}), hydrogen atom (H{sup {center_dot}}) (reducing species) and Cl{sub 2}{sup {center_dot}}{sup -},Br{sub 2}{sup {center_dot}}{sup -},{sup {center_dot}}N{sub 3},{sup {center_dot}}OH radicals (oxidizing species) with berberine or palmatine in aqueous solution have been studied by steady-state and pulse radiolysis. The spectra of transient intermediates, leading to the final products, are presented. The rate constants of the reaction of e{sub aq}{sup -} and {sup {center_dot}}OH radical with both alkaloids in the homogenous solution and in the presence of DNA are reported. It is demonstrated that the primary products of the reaction of berberine and palmatine with e{sub aq}{sup -} and radicals generated during radiolysis are unstable and undergo further reactions.

  17. The crystal growth of barium flouride in aqueous solution

    Science.gov (United States)

    Barone, J. P.; Svrjcek, D.; Nancollas, G. H.

    1983-06-01

    The kinetics of growth of barium flouride seed crystals were investigated in aqueous solution at 25°C using a constant composition method, in which the supersaturation and ionic strength were maintained constant by the addition of titrants consisting of barium nitrate and potassium flouride solutions. The rates of reaction, studied over a range of supersaturation (σ ≈ 0.4 to 1.0), were interpreted in terms of crystal growth models. A spiral growth mechanism best describes the data, and scanning electron microscopy indicates a three-dimensional growth. In the presence of inorganic additives such as phosphate, however, induction periods precede a morphological two-dimensional crystallization. Coulter Counter results show little crystal agglomeration.

  18. Radiolysis of pentachlorophenol (PCP) in aqueous solution by gamma radiation

    Institute of Scientific and Technical Information of China (English)

    XUE Jun; WANG Jianlong

    2008-01-01

    Steady-state radiolysis experiments were performed to investigate the y-irradiation treatment of pentachlorophenol (PCP) in aqueoussolution. The effect of initial concentration on the PCP degradation was also investigated. The experimental results showed that γ-irradiation was able to degrade PCP in aqueous solution successfully, and the radiolytical degradation process of PCP could be describedby the first-order kinetic model. When the initial concentration of PCP was 25 and 50 mg/L and the radiation dose was 4 and 6 kGy,respectively, the degradation efficiency was 100%. A luminescence bacterial test was used for evaluating the toxicity of the radiolyticintermediate products. Total detoxification of a 75 mg/L PCP solution could be achieved by carrying out the irradiation procedure at the dose of 15 kGy.

  19. Analysis and modeling of alkali halide aqueous solutions

    DEFF Research Database (Denmark)

    Kim, Sun Hyung; Anantpinijwatna, Amata; Kang, Jeong Won;

    2016-01-01

    A new model is proposed for correlation and prediction of thermodynamic properties of electrolyte solutions. In the proposed model, terms of a second virial coefficient-type and of a KT-UNIFAC model are used to account for a contribution of binary interactions between ion and ion, and water and ion...... on calculations for various electrolyte properties of alkali halide aqueous solutions such as mean ionic activity coefficients, osmotic coefficients, and salt solubilities. The model covers highly nonideal electrolyte systems such as lithium chloride, lithium bromide and lithium iodide, that is, systems......, respectively, with a Debye-Hückel term for electrostatic interactions. In a second approach of the model, additional parameters for interactions of ion pairs in the KT-UNIFAC are introduced as a correction to get better agreement with data. Structural parameters of ions used in the framework of UNIFAC...

  20. Photoelectron spectra of aqueous solutions from first principles.

    Energy Technology Data Exchange (ETDEWEB)

    Gaiduk, A.lex P.; Govoni, Marco; Seidel, Robert; Skone, Jonathan H.; Winter, Bernd; Galli, Giulia

    2016-06-08

    We present a combined computational and experimental study of the photoelectron spectrum of a simple aqueous solution of NaCl. Measurements were conducted on microjets, and first-principles calculations were performed using hybrid functionals and many-body perturbation theory at the G0W0 level, starting with wave functions computed in ab initio molecular dynamics simulations. We show excellent agreement between theory and experiments for the positions of both the solute and solvent excitation energies on an absolute energy scale and for peak intensities. The best comparison was obtained using wave functions obtained with dielectric-dependent self-consistent and range-separated hybrid functionals. Our computational protocol opens the way to accurate, predictive calculations of the electronic properties of electrolytes, of interest to a variety of energy problems.

  1. The radiation chemistry of aqueous sodium terephthalate solutions

    International Nuclear Information System (INIS)

    The radiation chemistry of cobalt-60 gamma-irradiated aqueous sodium terephthalate solutions has been studied. In aerated 4 x 10-4M sodium hydroxide solutions, the main products are hydroxyterephthalate (HTA) (G = 0.99 +- 0.01), carbonate (G = 1.31 +- 0.08), and peroxides (G = 2.84 +- 0.04). The HTA and carbonate species are both formed as a result of hydroxyl radical attack and account for approximately 90 per cent of hydroxyl radical reactions. Oxygen needs to be present for efficient conversion of the terephthalate-OH radical adduct to HTA and oxygenation increases G(HTA) above the aerated solution value. G(HTA) is unaffected by changes in terephthalate concentration between 1 x 10-4M and 1 x 10-2M in sodium hydroxide solutions at pH 10. Decreasing the solution pH does however affect G(HTA). In phosphate buffered solutions pH 6.85, G(HTA) is 0.93 +- 0.01 and lower values are obtained with further decrease in solution pH. The lowering of the G(HTA) value is attributed to recombination reactions between the terephthalate-OH radical products and reducing radical products. Experimental evidence supporting the recombination postulate was obtained from the measurement of a parallel decrease in the peroxide yield and the observation of a dose rate effect on G(HTA). Competition kinetic studies with the added solutes carbonate and bicarbonate gave the rate ratios k (OH + TA2-) : k(OH + CO32-) : k(OH + HCO3-) = 1 : 0.105 : 0.0036

  2. Novel Ag/Kaolin Nanocomposite as Adsorbent for Removal of Acid Cyanine 5R from Aqueous Solution

    OpenAIRE

    Saeedeh Hashemian; Mohammad Reza Shahedi

    2013-01-01

    Ag/kaolin nanocomposite was prepared by reduction of Ag+ ion with ethanol at alkaline condition on kaolin surface. Nanocomposite was characterized by FTIR, XRD, TEM, and BET methods. Results showed the Ag/kaolin composite has particle size 50 nm. The surface area was increased from kaolin to Ag/kaolin from 1.0215 to 7.409 m2 g−1, respectively. Ag/kaolin nanocomposite was used for adsorption of acid cyanine 5R (AC5R) from aqueous solution. The effect of parameters such as contact time, pH, an...

  3. Preparation of metallic nanoparticles by irradiation in starch aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Nemţanu, Monica R., E-mail: monica.nemtanu@inflpr.ro; Braşoveanu, Mirela, E-mail: monica.nemtanu@inflpr.ro; Iacob, Nicuşor, E-mail: monica.nemtanu@inflpr.ro [National Institute for Lasers, Plasma and Radiation Physics, Electron Accelerators Laboratory, 409 Atomiştilor St., PO Box MG-36, 077125, Bucharest-Măgurele (Romania)

    2014-11-24

    Colloidal silver nanoparticles (AgNPs) were synthesized in a single step by electron beam irradiation reduction of silver ions in aqueous solution containing starch. The nanoparticles were characterized by spectrophotocolorimetry and compared with those obtained by chemical (thermal) reduction method. The results showed that the smaller sizes of AgNPs were prepared with higher yields as the irradiation dose increased. The broadening of particle size distribution occurred by increasing of irradiation dose and dose rate. Chromatic parameters such as b* (yellow-blue coordinate), C* (chroma) and ΔE{sub ab} (total color difference) could characterize the nanoparticles with respect of their concentration. Hue angle h{sup o} was correlated to the particle size distribution. Experimental data of the irradiated samples were also subjected to factor analysis using principal component extraction and varimax rotation in order to reveal the relation between dependent variables and independent variables and to reduce their number. The radiation-based method provided silver nanoparticles with higher concentration and narrower size distribution than those produced by chemical reduction method. Therefore, the electron beam irradiation is effective for preparation of silver nanoparticles using starch aqueous solution as dispersion medium.

  4. New terahertz dielectric spectroscopy for the study of aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    George, Deepu K.; Charkhesht, Ali; Vinh, N. Q., E-mail: Vinh@vt.edu [Department of Physics, Virginia Tech, Blacksburg, Virginia 24061 (United States)

    2015-12-15

    We present the development of a high precision, tunable far-infrared (terahertz) frequency-domain dielectric spectrometer for studying the dynamics of biomolecules in aqueous solutions in the gigahertz-to-terahertz frequency. As an important benchmark system, we report on the measurements of the absorption and refractive index for liquid water in the frequency range from 5 GHz to 1.12 THz (0.17–37.36 cm{sup −1} or 0.268–60 mm). The system provides a coherent radiation source with power up to 20 mW in the gigahertz-to-terahertz region. The dynamic range of our instrument reaches 10{sup 12} and the system achieves a spectral resolution of less than 100 Hz. The temperature of samples can be controlled precisely with error bars of ±0.02 °C from 0 °C to 90 °C. Given these attributes, our spectrometer provides unique capabilities for the accurate measurement of even very strongly absorbing materials such as aqueous solutions.

  5. New terahertz dielectric spectroscopy for the study aqueous solutions

    CERN Document Server

    George, Deepu K; Vinh, N Q

    2015-01-01

    We present a development of a high precision, tunable far-infrared (terahertz) frequency-domain dielectric spectrometer for studying the dynamics of biomolecules in aqueous solutions in the gigahertz-to-terahertz frequency. As a first application we report on the measurement of the absorption and refractive index for liquid water in the frequency range from 5 GHz to 1.12 THz (0.17 to 37.36 cm-1 or 0.268 to 60 mm). The system provides a coherent radiation source with a power up to 20 mW in the gigahertz-to-terahertz region. The power signal-to-noise ratio of our instrument reaches 1015 and the system achieves a spectral resolution of less than 100 Hz. The temperature of samples can be controlled precisely with an error bars of 0.02 oC from above 0 oC to 90 oC. Given these attributes, our spectrometer provides unique capabilities for the accurate measurement of even very strongly absorbing materials such as aqueous solutions.

  6. Removal of heavy metals from aqueous solution by sawdust adsorption

    Institute of Scientific and Technical Information of China (English)

    BULUT Yasemin; TEZ Zeki

    2007-01-01

    The adsorption of lead, cadmium and nicel from aqueous solution by sawdust of walnut was investigated. The effect of contact time,initial metal ion concentration and temperature on metal ions removal has been studied. The equilibrium time was found to be of the order of 60 min. Kinetics fit pseudo first-order, second-order and intraparticle diffusion models, hence adsorption rate constants were calculated. The adsorption data of metal ions at temperatures of 25, 45 and 60C have been described by the Freundlich and Langmuir isotherm models. The thermodynamic parameters such as energy, entropy and enthalpy changes for the adsorption of heavy metal ions have also been computed and discussed. Ion exchange is probably one of the major adsorption mechanisms for binding divalent metal ions to the walnut sawdust. The selectivity order of the adsorbent is Pb(Ⅱ)≈Cd(Ⅱ)>Ni(Ⅱ). From these results, it can be concluded that the sawdust of walnut could be a good adsorbent for the metal ions from aqueous solutions.

  7. Efficient removal of mercury from aqueous solutions and industrial effluent.

    Science.gov (United States)

    Dos Santos, Maria B P; Leal, Katia Z; Oliveira, Fernando J S; Sella, Silvia M; Vieira, Méri D; Marques, Elisa M D; Gomes, Vanessa A C

    2015-01-01

    The objective of this study was to examine the ability of a solid waste produced during beneficiation of ornamental rocks to remove mercury (Hg) from an industrial effluent and aqueous solutions under various conditions. Batch studies have been carried out by observing the effects of pH, concentration of the adsorbate, contact time, and so on. Various sorption isotherm models such as Langmuir, Freundlich, and Tóth have been applied for the adsorbent. Film and intraparticle diffusion were both found to be rate-limiting steps. Adsorption was properly described by the Freundlich model (capacity constant of 0.3090 (mg g(-1))(mg L(-1))(-1/n) and adsorption intensity indicator of 2.2939), which indicated a favorable sorption and encouraged subsequent studies for treatment of Hg-containing industrial effluent. Industrial effluent treatment efficiency reached Hg removals greater than 90% by using ornamental rock solid waste (ORSW). Besides, desorption studies indicated that the maximum recovery of mercury was 100 ± 2% for 1 mol L(-1) HNO3 and 74 ± 8% for 0.1 mol L(-1) HNO3. The ORSW could be reused thrice without significant difference on the Hg removal rate from industrial effluent. These findings place ORSW as a promising efficient and low-cost adsorbent for the removal of Hg from aqueous solutions and industrial effluent. PMID:26301849

  8. Gamma radiolytic degradation of naphthalene in aqueous solution

    Science.gov (United States)

    Chu, Libing; Yu, Shaoqing; Wang, Jianlong

    2016-06-01

    The decomposition of naphthalene in aqueous solution was studied using gamma irradiation combined with both H2O2 and TiO2 nanoparticles. Gamma irradiation led to a complete degradation of naphthalene and a partial mineralization. With initial concentration of 5-32 mg/L, more than 98% of naphthalene was removed and TOC reduction reached 28-31% at an absorbed dose of 3.0 kGy. The degradation of naphthalene was faster at neutral pH and the initial degradation rate increased with increasing the initial concentration of naphthalene. Addition of H2O2 and TiO2 nanoparticles all enhanced the degradation and mineralization of naphthalene. TOC removal efficiency increased from 28% (irradiation alone) to 35% with addition of H2O2 (40 mg/L), and to 48% with addition of TiO2 (0.8 g/L). The degradation of naphthalene in aqueous solution by gamma irradiation was mainly through the oxidation by ·OH radicals. The intermediate naphthol and carboxylic acids such as formic acid and oxalic acid were identified by LC-MS and IC.

  9. Examination of rheological properties of aqueous solutions of sodium caseinate

    Directory of Open Access Journals (Sweden)

    Jolanta Gawałek

    2012-12-01

    Full Text Available Application of sodium caseinate as a functional additive in manufacturing processes requires production of its concentrated aqueous solutions which, in industrial conditions, presents a number of difficulties. In order to develop an effective and optimal industrial process of mixing – manufacturing a concentrated solution of sodium caseinate, it is essential to know rheological properties in a definite range of concentrations changing in the course of the dissolving process. The material for investigations was typical commercial sodium caseinate in the form of dry powder manufactured in Poland from acid casein using the method of extrusion. The objective of the undertaken empirical studies was the assessment of the impact of the concentration on rheological properties of sodium caseinate concentrates. Investigations were carried out for five concentrates manufactured in a mixer equipped in a mechanical agitator at concentrations ranging X (% Î (2.5¸12.5 and changing mass proportions of sodium caseinate in the aqueous solution as follows: GS/G (kgS·kg-1 = 0.025. On the basis of the obtained research results, classical flow curves were plotted for individual concentrates. The determined values of viscosity and density of the examined solutions were correlated in the form of h = f(GS/G and r = f(GS/G dependencies which were used during the determination of classical characteristics of mixing forces essential for the assessment of energetic expenditures required to manufacture concentrates in a mixer equipped in a mechanical agitator. The density of the examined concentrates increased in a way directly proportional, while the dynamic viscosity coefficient increased exponentially together with the increase of sodium caseinate concentration. Sodium caseinate concentrates exhibited Newtonian character in the examined range of concentrations.

  10. Method of precipitating uranium from an aqueous solution and/or sediment

    Science.gov (United States)

    Tokunaga, Tetsu K; Kim, Yongman; Wan, Jiamin

    2013-08-20

    A method for precipitating uranium from an aqueous solution and/or sediment comprising uranium and/or vanadium is presented. The method includes precipitating uranium as a uranyl vanadate through mixing an aqueous solution and/or sediment comprising uranium and/or vanadium and a solution comprising a monovalent or divalent cation to form the corresponding cation uranyl vanadate precipitate. The method also provides a pathway for extraction of uranium and vanadium from an aqueous solution and/or sediment.

  11. Melittin Aggregation in Aqueous Solutions: Insight from Molecular Dynamics Simulations.

    Science.gov (United States)

    Liao, Chenyi; Esai Selvan, Myvizhi; Zhao, Jun; Slimovitch, Jonathan L; Schneebeli, Severin T; Shelley, Mee; Shelley, John C; Li, Jianing

    2015-08-20

    Melittin is a natural peptide that aggregates in aqueous solutions with paradigmatic monomer-to-tetramer and coil-to-helix transitions. Since little is known about the molecular mechanisms of melittin aggregation in solution, we simulated its self-aggregation process under various conditions. After confirming the stability of a melittin tetramer in solution, we observed—for the first time in atomistic detail—that four separated melittin monomers aggregate into a tetramer. Our simulated dependence of melittin aggregation on peptide concentration, temperature, and ionic strength is in good agreement with prior experiments. We propose that melittin mainly self-aggregates via a mechanism involving the sequential addition of monomers, which is supported by both qualitative and quantitative evidence obtained from unbiased and metadynamics simulations. Moreover, by combining computer simulations and a theory of the electrical double layer, we provide evidence to suggest why melittin aggregation in solution likely stops at the tetramer, rather than forming higher-order oligomers. Overall, our study not only explains prior experimental results at the molecular level but also provides quantitative mechanistic information that may guide the engineering of melittin for higher efficacy and safety. PMID:26208115

  12. Adsorption of cesium on cement mortar from aqueous solutions.

    Science.gov (United States)

    Volchek, Konstantin; Miah, Muhammed Yusuf; Kuang, Wenxing; DeMaleki, Zack; Tezel, F Handan

    2011-10-30

    The adsorption of cesium on cement mortar from aqueous solutions was studied in series of bench-scale tests. The effects of cesium concentration, temperature and contact time on process kinetics and equilibrium were evaluated. Experiments were carried out in a range of initial cesium concentrations from 0.0103 to 10.88 mg L(-1) and temperatures from 278 to 313 K using coupons of cement mortar immersed in the solutions. Non-radioactive cesium chloride was used as a surrogate of the radioactive (137)Cs. Solution samples were taken after set periods of time and analyzed by inductively coupled plasma mass spectroscopy. Depending on the initial cesium concentration, its equilibrium concentration in solution ranged from 0.0069 to 8.837 mg L(-1) while the respective surface concentration on coupons varied from 0.0395 to 22.34 μg cm(-2). Equilibrium test results correlated well with the Freundlich isotherm model for the entire test duration. Test results revealed that an increase in temperature resulted in an increase in adsorption rate and a decrease in equilibrium cesium surface concentration. Among several kinetic models considered, the pseudo-second order reaction model was found to be the best to describe the kinetic test results in the studied range of concentrations. The adsorption activation energy determined from Arrhenius equation was found to be approximately 55.9 kJ mol(-1) suggesting that chemisorption was the prevalent mechanism of interaction between cesium ions and cement mortar.

  13. Peculiarity of aqueous solutions of 2,2,2-trifluoroethanol.

    Science.gov (United States)

    Burakowski, Andrzej; Gliński, Jacek; Czarnik-Matusewicz, Bogusława; Kwoka, Paulina; Baranowski, Andrzej; Jerie, Kazimierz; Pfeiffer, Helge; Chatziathanasiou, Nikos

    2012-01-12

    Aqueous solutions of 2,2,2-trifluoroethanol appear to show a structural transition at alcohol mole fraction equal to x(TFE) = 0.05, which can be concluded from a discontinuity of the speed of sound. At the same concentration, a discontinuity was observed in the parameters of the long-living component of the positron annihilation spectrum. Moreover, the partial molar volumes of components show transition-like behavior in the range of low solute contents, which is significantly different from nonsubstituted ethanol. The peculiarities of the low concentration system correlate with minor infrared spectra changes assigned to a mode composed of the CH(2) bending and CF(3) stretching internal vibrations being sensitive to polarity of the hydration shell surrounding the solute. The majority of the spectral changes arise from a gradual shift of the equilibrium between trans ↔ gauche isomers when the composition of the solution is changing. A possible explanation for the peculiar behavior of the system is a thermodynamic equilibrium between hydrated monomers and dimers at that respective mole number. PMID:22142252

  14. Structural rearrangement of mesostructured silica nanoparticles incorporated with ZnO catalyst and its photoactivity: Effect of alkaline aqueous electrolyte concentration

    Energy Technology Data Exchange (ETDEWEB)

    Jusoh, N.W.C. [Department of Chemical Engineering, Faculty of Chemical Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia); Jalil, A.A., E-mail: aishah@cheme.utm.my [Department of Chemical Engineering, Faculty of Chemical Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia); Institute of Hydrogen Economy, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia); Triwahyono, S.; Karim, A.H. [Department of Chemistry, Faculty of Science, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia); Salleh, N.F. [Department of Chemical Engineering, Faculty of Chemical Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia); Annuar, N.H.R.; Jaafar, N.F.; Firmansyah, M.L. [Department of Chemistry, Faculty of Science, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia); Mukti, R.R. [Division of Inorganic and Physical Chemistry, Faculty of Mathematics and Natural Science, Institut Teknologi Bandung, Jl Ganesha No 10, Bandung 40132 (Indonesia); Ali, M.W. [Department of Chemical Engineering, Faculty of Chemical Engineering, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia); Institute of Hydrogen Economy, Universiti Teknologi Malaysia, 81310 UTM Johor Bahru, Johor (Malaysia)

    2015-03-01

    Graphical abstract: - Highlights: • Hierarchical-like structure of MSN was formed in alkaline aqueous electrolyte. • Desilication generated abundant silanol groups and oxygen vacancies. • Zn{sup 2+} inserted to external –OH groups of the MSN to form Si–O–Zn bonds. • Oxygen vacancies trapped electrons to enhance electron–hole pair separation. • Hydroxyl radical generated from three main sources greatly influenced photoactivity. - Abstract: ZnO-incorporated mesostructured silica nanoparticles (MSN) catalysts (ZM) were prepared by the introduction of Zn ions into the framework of MSN via a simple electrochemical system in the presence of various concentrations of NH{sub 4}OH aqueous solution. The physicochemical properties of the catalysts were studied by XRD, {sup 29}Si MAS NMR, nitrogen adsorption–desorption, FE-SEM, TEM, FTIR, and photoluminescence spectroscopy. Characterization results demonstrated that the alkaline aqueous electrolyte simply generated abundant silanol groups on the surface of the catalysts as a consequence of desilication to form the hierarchical-like structure of the MSN. Subsequent restructuring of the silica network by the creation of oxygen vacancies and formation of Si–O–Zn during the electrolysis, as well as formation of new Si–O–Si bonds during calcination seemed to be the main factors that enhanced the catalytic performance of photodecolorization of methyl orange. A ZM prepared in the presence of 1.0 M NH{sub 4}OH (ZM-1.0) was determined to be the most effective catalyst. The catalyst displays a higher first-order kinetics rate of 3.87 × 10{sup −1} h{sup −1} than unsupported ZnO (1.13 × 10{sup −1} h{sup −1}) that prepared under the same conditions in the absence of MSN. The experiment on effect of scavengers showed that hydroxyl radicals generated from the three main sources; reduced O{sub 2} at the conduction band, decomposed water at the valence band and irradiated H{sub 2}O{sub 2} in the solution

  15. Adsorption and Desorption Behavior of Tannic Acid in Aqueous Solution on Polyaniline Adsorbent

    Institute of Scientific and Technical Information of China (English)

    WANG Jiahong; JI Yanfen; DING Shaolan; MA Hongrui; HAN Xiaojing

    2013-01-01

    Tannic acid is generally considered as one of polyphenolic pollutants,which may cause severe threats to the environment.In this study,polyaniline adsorbent was synthesized by chemical oxidation to remove tannic acid in aqueous solutions.The adsorption amount of tannic acid varied greatly with pH of solution and strong adsorption was at pH 5.8-6.7.Coexisting cations,such as Na+,K+,and Ca2+,can enhance the adsorption of tannic acid on polyaniline,which may be contributed to the electrostatic interaction between tannic acid and polyaniline.The adsorption process could be well described by Langmuir model and the maximum adsorption capacity was 117.65 mg·g-1 at 35 ℃ and pH 6.0.The thermodynamic parameters calculated from the adsorption isotherms indicate that the adsorption of tannic acid is spontaneous and endothermic process.The polyaniline saturated with tannic acid can be desorbed in alkaline solution and regenerated adsorbent can be used repeatedly with high adsorption capacity,which implies that polyaniline adsorbents have a great potential in water purification for the removal of tannic acid.

  16. Electrochemical behaviour of teflon-bonded iron electrodes in alkaline solutions

    Energy Technology Data Exchange (ETDEWEB)

    Periasamy, P. [Central Electrochemical Research Institute, Karaikudi (India); Ramesh Babu, B. [Central Electrochemical Research Institute, Karaikudi (India); Venkatakrishna Iyer, S. [Central Electrochemical Research Institute, Karaikudi (India)

    1996-11-01

    The electrochemical behaviour of Teflon-bonded iron oxide electrodes in 5.35 M KOH+0.65 M LiOH solution that contains various additives (such as thiourea, ethylenediaminetetraacetic acid (EDTA), hexamine and sodium sulfide) is examined by cyclic voltammetry, chronopotentiometry, open-circuit potential (OCP) decay and charge/discharge studies. The incorporation of Na{sub 2}S in the alkaline electrolyte improves the performance of iron oxide electrodes by increasing the value of the OCP and decreasing the transient time. Moreover, the addition of Na{sub 2}S gives maximum capacity for the iron oxide electrode and a value of zero for dE/dt. The addition of thiourea lowers the performance of pressed iron electrodes. Thus, the incorporation of Na{sub 2}S in the alkaline electrolyte is essential for improving the performance of these electrodes. (orig.)

  17. Aqueous solution synthesis of zinc oxide for application in optoelectronics

    Science.gov (United States)

    Joo, John Hwajong

    Recently, ZnO has garnered widespread attention in the semiconductor community for its large set of useful properties, which include a wide bandgap and its resulting optical transparency, a large exciton binding energy, a significant piezoelectric response, and good electrical conductivity. In many ways, it shares many properties with a widely used and technologically important semiconductor GaN, which is widely used for blue LEDs and lasers. However, ZnO cannot substitute for GaN in most optoelectronic applications, because it cannot be doped p-type. On the other hand, unlike many traditional, covalently bonded semiconductors like GaN, ZnO can be easily formed aqueous solutions at close to room temperature and pressure in the form of large crystals or a variety of nanostructures, making possible applications that are normally very difficult with traditional semiconductors. In this light, we aimed to take advantage of aqueous solution-based, ZnO growth techniques and incorporated ZnO structures novel optoelectronic and photonic structures. By controlling the morphology of ZnO, we studied the effects of nanowire-based ZnO/Cu2O solar cells. Carrier collection was increased using a nanowire-based device architecture. The main result, however, was the time evolution of the performance of these devices due to the movement of ionized defects in the material. The effects of geometry on the ageing characteristics were studied, which showed that the carrier collection could be increased further with aging in a nanowire Cu2O solar cell. The aging behavior was substantially different between nanowire and planar solar cells, which implies that future design of nanostructured solar cells must long term aging effects. In addition to solar cells, we explored the possibilities of using aqueous solution growth of ZnO to fabricated whispering gallery mode optical cavities and waveguides for enhancing extraction from a single photon source. In both applications, we used templated

  18. Preparation1 and utilization of wheat straw anionic sorbent for the removal of nitrate from aqueous solution

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    In order to reduce the impact of eutrophication caused by agricultural residues (i.e. excess nitrate) in aqueous solution, economic and effective anionic sorbents are required. In this article, we prepared anionic sorbent using wheat straw. Its structural characteristics and adsorption properties for nitrate removal from aqueous solution were investigated. The results indicate that the yield of the prepared anionic sorbent, the total exchange capacity, and the maximum adsorption capacity were 350%, 2.57 mEq/g, and 2.08 mmol/g, respectively. The Freundlich isotherm mode is more suitable than the Langmuir mode and the adsorption process accords with the first order reaction kinetic rate equation. When multiple anions (SO42-, H2PO4-, NO3-, and NO2-) were present, the isotherm mode of prepared anionic sorbent for nitrate was consistent with Freundlich mode; however, the capacity of nitrate adsorption was reduced by 50%. In alkaline solutions, about 90% of adsorbed nitrate ions could be desorbed from prepared anionic sorbent. The results of this study confirmed that the wheat straw anionic sorbent can be used as an excellent nitrate sorbent that removes nitrate from aqueous solutions.

  19. DNA dynamics in aqueous solution: opening the double helix

    Science.gov (United States)

    Pohorille, A.; Ross, W. S.; Tinoco, I. Jr; MacElroy, R. D. (Principal Investigator)

    1990-01-01

    The opening of a DNA base pair is a simple reaction that is a prerequisite for replication, transcription, and other vital biological functions. Understanding the molecular mechanisms of biological reactions is crucial for predicting and, ultimately, controlling them. Realistic computer simulations of the reactions can provide the needed understanding. To model even the simplest reaction in aqueous solution requires hundreds of hours of supercomputing time. We have used molecular dynamics techniques to simulate fraying of the ends of a six base pair double strand of DNA, [TCGCGA]2, where the four bases of DNA are denoted by T (thymine), C (cytosine), G (guanine), and A (adenine), and to estimate the free energy barrier to this process. The calculations, in which the DNA was surrounded by 2,594 water molecules, required 50 hours of CRAY-2 CPU time for every simulated 100 picoseconds. A free energy barrier to fraying, which is mainly characterized by the movement of adenine away from thymine into aqueous environment, was estimated to be 4 kcal/mol. Another fraying pathway, which leads to stacking between terminal adenine and thymine, was also observed. These detailed pictures of the motions and energetics of DNA base pair opening in water are a first step toward understanding how DNA will interact with any molecule.

  20. Arsenic Removal from Aqueous Solutions by Salvadora persica Stem Ash

    Directory of Open Access Journals (Sweden)

    Ferdos Kord Mostafapour

    2013-01-01

    Full Text Available Arsenic is a naturally occurring metalloid, which is widely distributed in nature and is regarded as the largest mass poisoning in history. In the present study, the adsorption potential of Salvadora persica (S. persica stem ash in a batch system for the removal of As(V from aqueous solutions was investigated. Isotherm studies were carried out to evaluate the effect of contact time (20–240 min, pH (2–11, initial arsenic concentration (50–500 μg/L, and adsorbent dose on sorption efficiency. Maximum removal efficiency of 98.33% and 99.32% was obtained at pH 6, adsorbent dosage 3.5 g/L, initial As(V concentration 500 μg/L, and contact time 80 and 60 min for S. persica stem ash at 300 °C and 500 °C, respectively. Also, the adsorption equilibriums were analyzed by the Langmuir and Freundlich isotherm models. Such equilibriums showed that the adsorption data was well fitted with the Freundlich isotherm model for S. persica stem ash at both 300 °C and 500 °C (R2=0.8983 and 0.9274, resp.. According to achieved results, it was defined that S. persica stem ash can be used effectively for As(V removal from the aqueous environment.

  1. Forecasting of thermodynamic properties of solution for non-polar molecules in aqueous salt solutions and in aqueous organic solutions

    International Nuclear Information System (INIS)

    The scaled particle theory has been used rather successfully to predict the values of thermodynamic properties of solution for non-polar molecules. Two very important parameters has been used in the equations of the scaled particle theory: the hard sphere diameter of the solute and the closeness of the solvent (closeness in which the diameters of the hard sphere particles forming the solvent are taken into account). With non-polar solutes, a correlation exists between calculated and experimental values of: free enthalpy of solution - enthalpy of solution - molar heat capacity change for the solution process. The fit between calculated and experimental values is only more qualitative than quantitative. However the variation of thermodynamic properties with the temperature and the modality is consistent with the variation calculated according to the scaled particle theory. (author)

  2. Comparison of Photochemical Reactions of m-Cresol in Aqueous Solution and in Ice

    Institute of Scientific and Technical Information of China (English)

    PENG Fei; XUE Hong-hai; TANG Xiao-jian; KANG Chun-li; LI Lin-lin; LI Zhe

    2012-01-01

    We compared the photochemical reaction of m-cresol containing OH precursors such as H2O2,NO2- and NO3- in aqueous solution with those in ice.The results show that the conversion rate of m-cresol in aqueous solution was higher than that in ice,H2O2,NO2- and NO3- all accelerated the photoconversion of m-cresol in both aqueous solution and ice.The photochemical reactions of m-cresol obeys the first order kinetics equation.According to the photoproducts identified by GC-MS,we proposed that hydroxylation and nitration reactions occurred in both aqueous solution and ice.Coupling reaction was common in ice,however,in aqueous solution it was found only in UV system.Our results suggest that the photochemical reactions of m-cresol were different in aqueous solution and in ice.

  3. γ-Irradiation of malic acid in aqueous solutions

    Science.gov (United States)

    Negron-Mendoza, Alicia; Graff, Rebecca L.; Ponnamperuma, Cyril

    1980-12-01

    The γ-irradiation of malic acid in aqueous solutions was studied under initially oxygenated and oxygen-free conditions in an attempt to determine the possible interconversion of malic acid into other carboxylic acids, specifically those associated with Krebs cycle. The effect of dose on product formation of the system was investigated. Gas-liquid chromatography combined with mass spectrometry was used as the principal means of identification of the non-volatile products. Thin layer chromotography and direct probe mass spectroscopy were also employed. The findings show that a variety of carboxylic acids are formed, with malonic and succinic acids in greatest abundance. These products have all been identified as being formed in the γ-irradiation of acetic acid, suggesting a common intermediary. Since these molecules fit into a metabolic cycle, it is strongly suggestive that prebiotic pathways provided the basis for biological systems.

  4. Degradation of chlorophenols in aqueous solution by {gamma}-radiation

    Energy Technology Data Exchange (ETDEWEB)

    Hu Jun [INET, Tsinghua University, Beijing 100084 (China)]. E-mail: hujun@mail.tsinghua.edu.cn; Wang Jianlong [INET, Tsinghua University, Beijing 100084 (China)

    2007-08-15

    Degradation of chlorophenols (CPs) in aqueous solutions by {gamma}-radiation was studied. The effect of absorbed dose on degradation, dechlorination and mineralization of CPs were investigated. The results indicated that the degradation of CPs, Cl{sup -} release and mineralization increased with increase in absorbed dose. When the initial concentration was 100 mg L{sup -1} and the dosage was 6 kGy, the removal efficiencies of CPs were 44.54% for 2-CP, 91.46% for 3-CP, 82.72% for 4-CP and 93.25% for 2,4-DCP, respectively. The combination of irradiation and H{sub 2}O{sub 2} leads to a synergistic effect, which remarkably increased the degradation efficiency of CPs and TOC removal. The kinetics of CPs during irradiation are also mentioned.

  5. Degradation of chlorophenols in aqueous solution by γ-radiation

    Science.gov (United States)

    Hu, Jun; Wang, Jianlong

    2007-08-01

    Degradation of chlorophenols (CPs) in aqueous solutions by γ-radiation was studied. The effect of absorbed dose on degradation, dechlorination and mineralization of CPs were investigated. The results indicated that the degradation of CPs, Cl - release and mineralization increased with increase in absorbed dose. When the initial concentration was 100 mg L -1 and the dosage was 6 kGy, the removal efficiencies of CPs were 44.54% for 2-CP, 91.46% for 3-CP, 82.72% for 4-CP and 93.25% for 2,4-DCP, respectively. The combination of irradiation and H 2O 2 leads to a synergistic effect, which remarkably increased the degradation efficiency of CPs and TOC removal. The kinetics of CPs during irradiation are also mentioned.

  6. Adsorption of CTAB onto perlite samples from aqueous solutions.

    Science.gov (United States)

    Alkan, Mahir; Karadaş, Mecit; Doğan, Mehmet; Demirbaş, Ozkan

    2005-11-15

    In this study, the adsorption properties of unexpanded and expanded perlite samples in aqueous cetyltrimethylammonium bromide (CTAB) solutions were investigated as a function of ionic strength, pH, and temperature. It was found that the amount of cetyltrimethylammonium bromide adsorbed onto unexpanded perlite was greater than that onto expanded perlite. For both perlite samples, the sorption capacity increased with increasing ionic strength and pH and decreasing temperature. Experimental data were analyzed by Langmuir and Freundlich isotherms and it was found that the experimental data were correlated reasonably well by the Freundlich adsorption isotherm. Furthermore, the isotherm parameters (KF and n) were also calculated. The adsorption enthalpy was determined from experimental data at different temperatures. Results have shown that the interaction between the perlite surface and CTAB is a physical interaction, and the adsorption process is an exothermic one.

  7. Gamma-irradiation of malic acid in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Negron-Mendoza, A.; Graff, R.L.; Ponnamperuma, C.

    1980-12-01

    The gamma-irradiation of malic acid in aqueous solutions was studied under initially oxygenated and oxygen-free conditions in an attempt to determine the possible interconversion of malic acid into other carboxylic acids, specifically those associated with Krebs cycle. The effect of dose on product formation of the system was investigated. Gas-liquid chromatography combined with mass spectrometry was used as the principal means of identification of the nonvolatile products. Thin layer chromatography and direct probe mass spectroscopy were also employed. The findings show that a variety of carboxylic acids are formed, with malonic and succinic acids in greatest abundance. These products have all been identified as being formed in the gamma-irradiation of acetic acid, suggesting a common intermediary. Since these molecules fit into a metabolic cycle, it is strongly suggestive that prebiotic pathways provided the basis for biological systems.

  8. Photo-degradation behaviour of roseoflavin in some aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Tyagi, A. [Institut II - Experimentelle und Angewandte Physik, Universitaet Regensburg, Universitaetsstrasse 31, D-93053 Regensburg (Germany); Penzkofer, A., E-mail: alfons.penzkofer@physik.uni-regensburg.de [Institut II - Experimentelle und Angewandte Physik, Universitaet Regensburg, Universitaetsstrasse 31, D-93053 Regensburg (Germany); Mathes, T.; Hegemann, P. [Institut fuer Biologie/Experimentelle Biophysik, Humboldt Universitaet zu Berlin, Invalidenstrasse 42, D-10115 Berlin (Germany)

    2010-03-24

    An absorption and emission spectroscopic characterization of roseoflavin (8-dimethylamino-8-demethyl-riboflavin, RoF) in aqueous solutions was carried out. The studies were concentrated on roseoflavin in pH 8 phosphate buffer. Absorption cross-section spectra, fluorescence excitation spectra, fluorescence quantum distributions, fluorescence quantum yields and fluorescence lifetimes were determined. The fluorescence of RoF is quenched by photo-induced intra-molecular charge-transfer at room temperature. The photo-degradation of RoF in un-buffered water, in Tris-HCl buffer, and in phosphate buffer was studied. Phosphate buffer and to a smaller extent Tris buffer catalyse the RoF photo-degradation. Photo-excitation of the primary photoproduct, 8-methylamino-riboflavin (8-MNH-RF), enhanced the RoF degradation by triplet 8-MNH-RF - singlet RoF excitation transfer with subsequent triplet-state RoF degradation.

  9. Degradation of aqueous solutions of camphor by heterogeneous photocatalysis.

    Science.gov (United States)

    Sirtori, Carla; Altvater, Priscila K; de Freitas, Adriane M; Peralta-Zamora, Patricio G

    2006-02-28

    In this study the photocatalytic degradation of aqueous solutions of camphor was investigated by using TiO2 and ZnO photocatalysts. In the presence of artificial UV-light the highly photosensitive camphor was almost totally degraded after reaction times of 60 min. However, under these conditions the mineralization degree was lower than 25%. In the presence of semiconductors the degradation was complete after a treatment time of about 30 min. Moreover, the mineralization was considerably greater, mainly with the use of TiO2 (> 80% at reaction time of 60 min). Heterogeneous photocatalytic processes applied in the presence of solar radiation show a promising degradation capability. TiO2-based processes afforded mineralization degrees of about 90% after a reaction time of 120 min, when the system was assisted by aeration.

  10. Protein thermal stabilization in aqueous solutions of osmolytes.

    Science.gov (United States)

    Bruździak, Piotr; Panuszko, Aneta; Jourdan, Muriel; Stangret, Janusz

    2016-01-01

    Proteins' thermal stabilization is a significant problem in various biomedical, biotechnological, and technological applications. We investigated thermal stability of hen egg white lysozyme in aqueous solutions of the following stabilizing osmolytes: Glycine (GLY), N-methylglycine (NMG), N,N-dimethylglycine (DMG), N,N,N-trimethylglycine (TMG), and trimethyl-N-oxide (TMAO). Results of CD-UV spectroscopic investigation were compared with FTIR hydration studies' results. Selected osmolytes increased lysozyme's thermal stability in the following order: Gly>NMG>TMAO≈DMG>TMG. Theoretical calculations (DFT) showed clearly that osmolytes' amino group protons and water molecules interacting with them played a distinctive role in protein thermal stabilization. The results brought us a step closer to the exact mechanism of protein stabilization by osmolytes. PMID:26495438

  11. Infrared spectroscopy for monitoring gas hydrates in aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Dobbs, G.T.; Luzinova, Y.; Mizaikoff, B. [Georgia Inst. of Technology, Atlanta, GA (United States). School of Chemistry and Biochemistry; Raichlin, Y.; Katzir, A. [Tel-Aviv Univ., Tel-Aviv (Israel). Shool of Physics and Astronomy

    2008-07-01

    This paper introduced the first principles for monitoring gas hydrate formation and dissociation in aqueous solution by evaluating state-responsive infrared (IR) absorption features of water with fiberoptic evanescent field spectroscopy. A first order linear functional relationship was also derived according to Lambert Beer's law in order to quantify the percentage gas hydrate within the volume of water probed via the evanescent field. In addition, spectroscopic studies evaluating seafloor sediments collected from a gas hydrate site in the Gulf of Mexico revealed minimal spectral interferences from sediment matrix components. As such, evanescent field sensing strategies were established as a promising perspective for monitoring the dynamics of gas hydrates in oceanic environments. 21 refs., 5 figs.

  12. Radiation-induced degradation of 4-chloroaniline in aqueous solution

    International Nuclear Information System (INIS)

    The radiation-induced decomposition of 4-chloroaniline (4-ClA) was studied under steady-state conditions using aqueous solutions saturated with air, pure oxygen, N2O, argon and argon in the presence of t-Butanol. Using HPLC-method, the initial G-values of the substrate degradation as well as of a number of radiolytic products were determined. The formation of aminophenols, chlorophenols, aniline and phenol in addition to chloride, ammonia, formaldehyde and mixture of aldehydes as well as carboxylic acids was studied as a function of absorbed dose. Based on the experimental data, probable reaction mechanisms for the degradation of 4-ClA by γ-rays and the formation of the identified products are presented

  13. Ionizing radiation induced degradation of monuron in dilute aqueous solution

    Science.gov (United States)

    Kovács, Krisztina; He, Shijun; Míle, Viktória; Földes, Tamás; Pápai, Imre; Takács, Erzsébet; Wojnárovits, László

    2016-07-01

    The decomposition of monuron was investigated in dilute aqueous solutions using pulse radiolysis and γ-radiolysis in order to identify the intermediates and final products. The main reaction takes place between monuron and the hydroxyl radicals yielding hydroxycyclohexadienyl type radicals with a second order rate constant of (7.4±0.2)×109 mol-1 dm3 s-1. In •OH reactions, the aminyl and phenoxyl radicals may also form. Dechlorination was observed in both hydroxyl radical and hydrated electron reactions. The •OH induced dechlorination reactions are suggested to occur through OH substitution or phenoxyl radical formation. The rate of oxidation is very high in the presence of dissolved oxygen. Some of the results are also supported by quantum chemical calculations.

  14. Adsorption of catechol from aqueous solution by aminated hypercrosslinked polymers

    Institute of Scientific and Technical Information of China (English)

    SUN Yue; LI Xiao-tao; XU Chao; CHEN Jin-long; LI Ai-min; ZHANG Quan-xing

    2005-01-01

    Adsorption of catechol from aqueous solution with the hypercrosslinked polymeric adsorbent NDA-100 and its derivatives AH-1,AH-2 and AH-3 aminated by dimethylamine, the commercial resin Amberlite XAD-4 and weakly basic anion exchanger resin D301 was compared. It was found that the aminated hypercrosslinked resins had the highest adsorption capacities among the tested polymers. The empirical Freundlich equation was successfully employed to describe the adsorption process. Specific surface area and micropore structure of the adsorbent, in company with tertiary amino groups on matrix affected the adsorption performance towards catechol. In addition,thermodynamic study was carried out to interpret the adsorption mechanism. Kinetic study testified that the tertiary amino groups on the polymer matrix could decrease the adsorption rate and increase the adsorption apparent activation energy.

  15. Aqueous dispersions of silver nanoparticles in polyelectrolyte solutions

    Indian Academy of Sciences (India)

    Dan Donescu; Raluca Somoghi; Marius Ghiurea; Raluca Ianchis; Cristian Petcu; Stefania Gavriliu; Magdalena Lungu; Claudia Groza; Carmen R Ionescu; Carmen Panzaru

    2013-03-01

    In this report, we present the versatile and effective technique, using environmental friendly reductant glucose, to prepare stable silver nanodispersions by reduction of Ag+ ions. Alternant copolymers of maleic anhydride with vinyl acetate and styrene sulphonate sodium acid salt polyelectrolytes were synthesized in aqueous solution and used as stabilizers. The formation of nano silver particles was confirmed by UV-Vis spectrophotometry and TEM measurements. Dynamic Light Scattering (DLS) measurements were needed to study how the reagents and their concentrations influence particle size. SEM images show the nanostructure of the hybrid films and indicate a strong interaction between the polyelectrolyte and the silver NPs. Moreover, the silver NPs could be stored for one year without observation of aggregates or sedimentation. The final solid products obtained after evaporating to dryness can be used to produce stable dispersions upon mixing with water. Few of the final products were found to exhibit a high antibacterial and antifungal activity.

  16. VISCOSITY BEHAVIOR OF LACQUER POLYSACCHARIDE IN AQUEOUS SOLUTION

    Institute of Scientific and Technical Information of China (English)

    QIU Xingping; ZHANG Lina; DU Yumin; QIAN Baogong

    1991-01-01

    The dependence of measured viscosity on NaCl concentration (0.1 to 3.0M), pH (range of 2-13) and cadoxen composition Wcad (from 2% to 100% ) for the lacquer polysaccharide in NaCl/cadoxen/H2O mixture containing HCl or without were obtained. All the viscosity exponents γ in the Mark-Houwink equations under three different solvent condition are close to 0.5. The wcad dependence of reduced viscosity ηsp/c confirms the single strand chain of the polysaccharide. As the γ values close to 0.5 and values of unperturbed dimension θ/M and [η] much smaller than those for usual linear polymers, these facts suggest that the polysaccharide chains in the aqueous solutions should be dense random coil owing to the highly branched structure.

  17. Adsorption of Anthraquinone Dyes from Aqueous Solutions by Penicillium Terrestre

    Institute of Scientific and Technical Information of China (English)

    XIN Bao-ping; LIU Xiao-mei

    2006-01-01

    Penicillium terrestre was used for removing four anthraquinone dyes from aqueous solution. The experiments were performed in Erlenmeyer flasks and spore suspension was used for inoculation. The results show that the mechanism of dye removal by penicillium terrestre is biosorption and the growing pellets exhibit higher adsorptive capacity than the resting or dead ones. The maximum removals of disperse blue 2BLN, reactive brilliant blue KN-R, acid anthraquinone blue and bromamine acid at the concentration of 120 mg/L by biosorption of growing pellets are 100 %, 100 %, 96 % and 91%, respectively. The 100.0 % and 91.4 % KN-R removals are achieved respectively at the much higher concentration of 250 and 400 mg/L. 2.5 g/L glucose is sufficient for 100% KN-R removal by growing pellets. Salinity (NaC1) increase from 0 to 2% (W/V) moderately accelerates both mycelium growth and KN-R removal.

  18. Extraction of certain radionuclides from aqueous schungite solutions

    International Nuclear Information System (INIS)

    The sorption of 90Sr, 106Ru, 137Cs, and 238Pu from aqueous solutions over a wide pH range was studied. Swelled schungite chips (Nigozero, Kondopozhsk region) (1) and schungite (Onezhsk lake) (2) were tested as sorbents. The minerals were used both untreated and after oxidation (HNO3, 1:1, contact time 1 day). The oxidation, judging from the literature, facilitates the formation of carboxylic and phenolic functional groups on the surface of the carbon-containing sorbents. The presence of such groups is responsible for the high selectivity of the sorbents for multicharged cations. Futhermore, the hydrophobicity of the schungites enormously decreases after the oxidation. The studied sorbents had an average particle size of 0.08-0.1 mm. The schungite was contacted with the solution under static conditions with periodic stirring in order to establish equilibrium. The concentration of the radionuclides was 2-4 MBq/liter. The solution volumes were 10 ml. The sorbent content was 0.01 g. The required pH was set by adding HCl or NaOH

  19. Aqueous solution of basic fuchsin as food irradiation dosimeter

    Institute of Scientific and Technical Information of China (English)

    Hasan M. KHAN; Shagufta NAZ

    2007-01-01

    Dosimetric characterization of aqueous solution of basic fuchsin was studied spectrophotometrically for possible application in the low-dose food irradiation dosimetry. Absorption spectra of unirradiated and irradiated solutions were determined and the decrease in absorbance with the dose was noted down. Radiation-induced bleaching of the dye was measured at wavelengths of maximum absorption λmax (540nm) as well as 510nm and 460 nm. At all these wavelengths, the decrease in absorbance of the dosimeter was linear with respect to the absorbed dose from 50 Gy to 600 Gy. The stability of dosimetric solution during post-irradiation storage in the dark at room temperature showed that after initial bleaching during first ten to twenty days, the response was almost stable for about 34 days. The study on the effect of different light and temperature conditions also showed that the response gradually decreased during the storage period of 34 days, which shows that basic fuchsin dye is photosensitive as well as thermally sensitive.

  20. Ultrasonic Measurements of Temperature in Aqueous Solutions: Why and How

    Directory of Open Access Journals (Sweden)

    A. Afaneh

    2011-01-01

    Full Text Available The paper describes two different approaches to ultrasonic measurements of temperature in aqueous solutions. The first approach uses two narrowband ultrasonic transducers and support electronics that form an oscillating sensor which output frequency is related to the measured temperature. This low-cost sensor demonstrated sensitivity of about 40 Hz/K at the distance of 190 mm and the operating frequency of about 25 kHz. The second approach utilised pulse-echo mode at the centre frequency of 20 MHz. The reflector featured a cavity that was filled with deionised water. The ultrasound propagation delay in the cavity was related to the temperature in the solution. The experiments were conducted for deionised water, and solutions of sodium persulfate, sodium chloride, and acetic acid with concentrations up to 0.5 M. In the experiments (conducted within the temperature range from 15 to 30°C, we observed increases in the ultrasound velocity for increased temperatures and concentrations as was expected. Measurement results were compared with literature data for pure and seawater. It was concluded that ultrasonic measurements of temperature were conducted with the resolution well below 0.1 K for both methods. Advantages of ultrasonic temperature measurements over conventional thermometers were discussed.

  1. Cations bind only weakly to amides in aqueous solutions.

    Science.gov (United States)

    Okur, Halil I; Kherb, Jaibir; Cremer, Paul S

    2013-04-01

    We investigated salt interactions with butyramide as a simple mimic of cation interactions with protein backbones. The experiments were performed in aqueous metal chloride solutions using two spectroscopic techniques. In the first, which provided information about contact pair formation, the response of the amide I band to the nature and concentration of salt was monitored in bulk aqueous solutions via attenuated total reflection Fourier transform infrared spectroscopy. It was found that molar concentrations of well-hydrated metal cations (Ca(2+), Mg(2+), Li(+)) led to the rise of a peak assigned to metal cation-bound amides (1645 cm(-1)) and a decrease in the peak associated with purely water-bound amides (1620 cm(-1)). In a complementary set of experiments, the effect of cation identity and concentration was investigated at the air/butyramide/water interface via vibrational sum frequency spectroscopy. In these studies, metal ion-amide binding led to the ordering of the adjacent water layer. Such experiments were sensitive to the interfacial partitioning of cations in either a contact pair with the amide or as a solvent separated pair. In both experiments, the ordering of the interactions of the cations was: Ca(2+) > Mg(2+) > Li(+) > Na(+) ≈ K(+). This is a direct cationic Hofmeister series. Even for Ca(2+), however, the apparent equilibrium dissociation constant of the cation with the amide carbonyl oxygen was no tighter than ∼8.5 M. For Na(+) and K(+), no evidence was found for any binding. As such, the interactions of metal cations with amides are far weaker than the analogous binding of weakly hydrated anions.

  2. Catalytic destruction of hazardous organics in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Baker, E.G.; Sealock, L.J. Jr.

    1988-04-01

    Pacific Northwest Laboratory (PNL) is developing a process for destroying hazardous organics and chlorinated organics in aqueous solutions. The process is targeted at liquid waste streams that are difficult and costly to treat with conventional or developing technologies. Examples of these waste streams include contaminated groundwater and surface water and industrial wastewater. Aqueous solutions are treated with a transition metal catalyst at 300/degree/C to 460/degree/C and 2000 to 5000 psig pressure to convert the wastes to innocuous gases. During proof-of-principle tests conducted in a 1-L batch reactor, destruction of over 99/percent/ (in most cases approaching 99.9/percent/) of the organic material was achieved. Hexone (methyl is isobutyl ketone, MIBK), p-cresol, hexane, benzene, and naphthalene were used as model waste materials. The only major product with all of the organic compounds was a gas containing 50/percent/ to 75/percent/ methane, 25/percent/ to 45/percent/ carbon dioxide, and 0/percent) to 5/percent/ hydrogen. Reduced nickel was the only effective catalyst and that the optimal operating conditions for destroying nonchlorinated organics were 350/degree/C to 400/degree/C, 2000 to 4000 psig, and 30/endash/ to 60/endash/min residence time. These tests also indicated that catalyst deactivation or fouling would not be a problem at these conditions. Chlorobenzene and trichloroethylene (TEC), were also tested. Destruction of both compounds was 99/percent/ or greater, but the products were different from those obtained from hydrocarbons. With TCE, the major product was carbon dioxide; with chlorobenzene the major product identified was benzene. In the tests with the chlorinated hydrocarbons, the chlorine was converted to HC1 and the reduced nickel was converted to nickel hydroxide, which may be detrimental to long-term catalyst activity. (15 refs., 8 figs., 6 tabs).

  3. Biosorption of arsenic from aqueous solution using dye waste.

    Science.gov (United States)

    Nigam, Shubha; Vankar, Padma S; Gopal, Krishna

    2013-02-01

    The purpose of this study is to examine on removal of arsenic from water by biosorption through potential application of herbal dye wastes. Four different flower dye residues (after extraction of natural dye) viz. Hibiscus rosasinensis, Rosa rosa, Tagetes erecta, and Canna indica were utilized successfully for the removal of arsenic from aqueous solution. Batch studies were carried out for various parameters viz. pH, sorbent dose, contact time, initial metal ion concentration, and temperature. Data were utilized for isothermal, kinetic, and thermodynamic studies. Scanning electron microscopy (SEM), energy-dispersive x-ray spectroscopy (EDAX), and Fourier transform infrared (FTIR) analyses of biomass were performed. The results showed that 1 g/100 ml for 5.0-5.5 h contact time at pH 6.0-7.5 with agitation rate 150 rpm provided 98, 96, 92, and 85 % maximum absorption of arsenic by R. rosa, H. rosasinensis, T. erecta, and C. indica, respectively, at initial concentration of 500 ppb. Data followed Langmuir isotherm showing sorption to be monolayer on heterogeneous surface of biosorbent. Negative values of ΔG° indicated spontaneous nature, whereas ΔH° indicates exothermic nature of system followed by pseudo-first-order adsorption kinetics. FTIR results showed apparent changes in functional group regions after metal chelation. SEM and EDAX analyses showed the changes in surface morphology of all test biosorbents. Herbal dye wastes, used as biosorbent, exhibited significant (85-98 %) removal of arsenic from aqueous solution. Hence, these biosorbents are cost-effective, easily available, eco-friendly, and comparatively more effective than other biosorbents already in use. These may be used to remove arsenic and other toxic metals from water. PMID:22661261

  4. Influence aqueous solutions on the mechanical behavior of argillaceous rocks

    International Nuclear Information System (INIS)

    The hydration of the shale with an aqueous solution induces a swelling deformation which plays an important role in the behaviour of the structures excavated in this type of grounds. This deformation is marked by a three-dimensional and anisotropic character and involves several mechanisms like adsorption, osmosis or capillarity. Several researches were dedicated to swelling and were often much debated due to the complexity of the implied phenomena. The goal of this thesis is therefore to contribute to a better understanding of shale swelling when the rock is confined and hydrated with an aqueous solution. The main part of the work accomplished was related to the Lorraine shale and to the Tournemire shale. To characterize swelling and to identify the main governing parameters, it was necessary to start the issue with an experimental approach. Many apparatus were then developed to carry out tests under various conditions of swelling. In order to facilitate the interpretation of the tests and thereafter the modelling of the behaviour, the experimental procedure adopted consisted of studying first the mechanical aspect and then the chemical aspect of swelling. In the mechanical part, swelling was studied by imposing on the sample a mechanical loading while maintaining during the tests the same aqueous solution. The principal parameters which were studied are the effect of the lateral conditions on axial swelling (impeded strain or constant stress) as well as the influence of the axial stress on radial swelling. The anisotropy of swelling was studied by carrying out, for different orientations of the sample, tests of free swelling, impeded swelling and uniaxial swelling. These various mechanical tests allowed to study the three-dimensional anisotropic swelling in all the conditions and to select the most appropriate test to be used in the second phase of the research. The precise analysis performed to explain the mechanisms behind the swelling of an argillaceous rock

  5. The Removal of Dye from Aqueous Solution by Adsorption on Low Cost Adsorbents

    OpenAIRE

    J. J. Chamargore; Bharad, J. V.; Madje, B. R.; Ubale, M. B.

    2010-01-01

    Removal of color from aqueous solution by using low cost easily available adsorbent was conducted by batch experiment. The potential of the low cost adsorbent (Marble powder-treated and untreated) to remove methylene red from aqueous solution were assessed at room temperature. Laboratory investigation of the potential of marble powder and sulphuric acid treated marble powder to remove dye color from aqueous solution has been studied. Parameters studied included pH, adsorbent dose, initial dye...

  6. KINETICS OF THE HYDROXYETHYLATION OF STARCH IN ALKALINE SALT-CONTAINING AQUEOUS SLURRIES

    NARCIS (Netherlands)

    VANWARNERS, A; STAMNHUIS, EJ; BEENACKERS, AACM

    1994-01-01

    A two-phase kinetic model is presented for the base-catalyzed hydroxyethylation of potato starch using ethylene oxide at temperatures between 293 and 318 K in aqueous starch slurries containing sodium sulfate. The rate of the hydroxyethylation of starch as a function of starch anion concentration (c

  7. Characterization of alkaline-earth oxide additions to the MnO2 cathode in an aqueous secondary battery

    International Nuclear Information System (INIS)

    Highlights: → Adding MgO in MnO2 cathode enhances the battery discharge capacity. → Mechanism appears to be different with those of our previously published results. → Capacity fade with subsequent cycling is reduced only for MgO but not for BaO. → Transferred the primary battery into a secondary while using LiOH as electrolyte. - Abstract: The effect of alkaline-earth oxide additions on aqueous rechargeable battery is investigated using microscopic and spectroscopic techniques. The alkaline-earth oxide additions such as magnesium oxide (MgO) and barium oxide (BaO) were physically mixed to the manganese dioxide (MnO2) cathode of a cell comprising zinc as an anode and aqueous lithium hydroxide as the electrolyte. The results showed that such additions greatly improved the discharge capacity of the battery (from 145 to 195 for MgO and 265 mAh/g for BaO). Capacity fade with subsequent cycling is reduced only for MgO but not for BaO. With an aim to understand the role of these additives and its improvement in cell performance, we have used microscopy, spectroscopy, ion beam analysis and diffraction based techniques to study the process. Transmission electron microscopy (TEM), and energy dispersive X-ray spectroscopy analysis (EDS) results showed evidence of crystalline MnO2 particles for MgO as additive, whereas, MnO2 particles with diffused structure leading to mixture of phases is observed for BaO additives which is in agreement with X-ray diffraction (XRD) data. This work relates to improvement in the electrochemical behaviour of the Zn-MnO2 battery while the MgO additive helps to reduce the formation of manganese and zinc such as hetaerolite that hinders the lithium intercalation.

  8. Characterization of alkaline-earth oxide additions to the MnO{sub 2} cathode in an aqueous secondary battery

    Energy Technology Data Exchange (ETDEWEB)

    Minakshi, Manickam, E-mail: minakshi@murdoch.edu.au [Extractive Metallurgy, Murdoch University, Murdoch, WA 6150 (Australia); Blackford, Mark [Institute of Materials Engineering, ANSTO, Lucas Heights, NSW 2234 (Australia); Ionescu, Mihail [Institute for Environment Research, ANSTO, Lucas Heights, NSW 2234 (Australia)

    2011-05-19

    Highlights: > Adding MgO in MnO{sub 2} cathode enhances the battery discharge capacity. > Mechanism appears to be different with those of our previously published results. > Capacity fade with subsequent cycling is reduced only for MgO but not for BaO. > Transferred the primary battery into a secondary while using LiOH as electrolyte. - Abstract: The effect of alkaline-earth oxide additions on aqueous rechargeable battery is investigated using microscopic and spectroscopic techniques. The alkaline-earth oxide additions such as magnesium oxide (MgO) and barium oxide (BaO) were physically mixed to the manganese dioxide (MnO{sub 2}) cathode of a cell comprising zinc as an anode and aqueous lithium hydroxide as the electrolyte. The results showed that such additions greatly improved the discharge capacity of the battery (from 145 to 195 for MgO and 265 mAh/g for BaO). Capacity fade with subsequent cycling is reduced only for MgO but not for BaO. With an aim to understand the role of these additives and its improvement in cell performance, we have used microscopy, spectroscopy, ion beam analysis and diffraction based techniques to study the process. Transmission electron microscopy (TEM), and energy dispersive X-ray spectroscopy analysis (EDS) results showed evidence of crystalline MnO{sub 2} particles for MgO as additive, whereas, MnO{sub 2} particles with diffused structure leading to mixture of phases is observed for BaO additives which is in agreement with X-ray diffraction (XRD) data. This work relates to improvement in the electrochemical behaviour of the Zn-MnO{sub 2} battery while the MgO additive helps to reduce the formation of manganese and zinc such as hetaerolite that hinders the lithium intercalation.

  9. Measurement and correlation of physical properties of aqueous solutions of tetrabutylammonium hydroxide, piperazine and their aqueous blends

    Institute of Scientific and Technical Information of China (English)

    Rizwan Safdar; Abdul Aziz Omar; Lukman B Ismail; Arhama Bari; Bhajan Lal

    2015-01-01

    The density, viscosity and refractive index of aqueous solutions of tetrabutylammonium hydroxide (TBAOH), pi-perazine (PZ) and their aqueous blends are determined at several temperatures (303.15 to 333.15 K). All these measured physicochemical properties decreases with an increase in temperature. The density data is used to cal-culate the coefficient of thermal expansion and excess molar volume of al aqueous binary and ternary solutions. The coefficient of thermal expansion increases with increase in temperatures and concentrations. The negativity of excess molar volume for al the aqueous solution decreased with increase in temperature. Each physical prop-erty is correlated with temperature by least square method and the corresponding coefficients for each property are presented. The prediction values from correlations for the physical properties are in good agreement with the experimental values.

  10. THE KINETICS OF SAPONIFICATION OF IODOACETIC ACID BY SODIUM HYDROXIDE AND BY CERTAIN ALKALINE BUFFER SOLUTIONS.

    Science.gov (United States)

    Brdicka, R

    1936-07-20

    1. The rate of the saponification of iodoacetic acid in sodium hydroxide and alkaline buffer solutions yielding glycollic acid was measured by means of Heyrovský's polarographic method. 2. From the bimolecular velocity constants, increasing with the ionic strength of the solution, the Brönsted factor, F, which characterizes the primary salt effect, was calculated. 3. In the borate buffer solutions the monomolecular constants of the saponification were determined which, at values above the pH of neutralization of boric acid, show a proportionality to the concentration of hydroxyl anions. Below the pH of neutralization of boric acid, they are proportional to the concentration of borate anions.

  11. Adsorption of cesium on cement mortar from aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Volchek, Konstantin, E-mail: konstantin.volchek@ec.gc.ca [Emergencies Science and Technology Section, Environment Canada, 335 River Road, Ottawa, Ontario, Canada K1A 0H3 (Canada); Miah, Muhammed Yusuf [Emergencies Science and Technology Section, Environment Canada, 335 River Road, Ottawa, Ontario, Canada K1A 0H3 (Canada); Department of Applied Chemistry and Chemical Technology, Noakhali Science and Technology University (Bangladesh); Kuang, Wenxing; DeMaleki, Zack [Emergencies Science and Technology Section, Environment Canada, 335 River Road, Ottawa, Ontario, Canada K1A 0H3 (Canada); Tezel, F. Handan [Department of Chemical and Biological Engineering, University of Ottawa, 161 Louis-Pasteur, Ottawa, Ontario, Canada K1N 6N5 (Canada)

    2011-10-30

    Highlights: {yields} The adsorption of cesium on cement mortar was investigated in a range of temperatures and cesium concentrations. {yields} The pseudo-second order kinetic model produced a good fit with the experimental kinetic data. {yields} Equilibrium test results correlated well with the Freundlich isotherm adsorption model. {yields} The interaction between cesium ions and cement mortar was dominated by chemical adsorption. - Abstract: The adsorption of cesium on cement mortar from aqueous solutions was studied in series of bench-scale tests. The effects of cesium concentration, temperature and contact time on process kinetics and equilibrium were evaluated. Experiments were carried out in a range of initial cesium concentrations from 0.0103 to 10.88 mg L{sup -1} and temperatures from 278 to 313 K using coupons of cement mortar immersed in the solutions. Non-radioactive cesium chloride was used as a surrogate of the radioactive {sup 137}Cs. Solution samples were taken after set periods of time and analyzed by inductively coupled plasma mass spectroscopy. Depending on the initial cesium concentration, its equilibrium concentration in solution ranged from 0.0069 to 8.837 mg L{sup -1} while the respective surface concentration on coupons varied from 0.0395 to 22.34 {mu}g cm{sup -2}. Equilibrium test results correlated well with the Freundlich isotherm model for the entire test duration. Test results revealed that an increase in temperature resulted in an increase in adsorption rate and a decrease in equilibrium cesium surface concentration. Among several kinetic models considered, the pseudo-second order reaction model was found to be the best to describe the kinetic test results in the studied range of concentrations. The adsorption activation energy determined from Arrhenius equation was found to be approximately 55.9 kJ mol{sup -1} suggesting that chemisorption was the prevalent mechanism of interaction between cesium ions and cement mortar.

  12. Comparison of Inactivation and Unfolding of Calf Intestinal Alkaline Phosphatase in Guanidinium Chloride Solution

    Institute of Scientific and Technical Information of China (English)

    张英侠; 闫淑莲; 刘永利; 席宏伟; 周海梦

    2002-01-01

    The changes in activity and unfolding of calf intestinal alkaline phosphatase (CIP) during denaturation in guanidinium chloride solutions of different concentrations were investigated using ultraviolet difference absorption spectra and fluorescence emission spectra. Unfolding and inactivation rate constants were measured and compared. The inactivation course is much faster than that of unfolding, which suggests that the active site of CIP containing two zinc ions and one magnesium ion is situated in a limited and flexible region of the enzyme molecule, which is more fragile to the denaturant than the protein as a whole.

  13. Pitting corrosion of friction stir welded aluminum alloy thick plate in alkaline chloride solution

    Energy Technology Data Exchange (ETDEWEB)

    Xu Weifeng, E-mail: xwf1982@mail.nwpu.edu.c [School of Materials and Engineering, Northwestern Polytechnical University, Xi' an 710072 (China); Liu Jinhe; Zhu Hongqiang [School of Materials and Engineering, Northwestern Polytechnical University, Xi' an 710072 (China)

    2010-03-01

    The pitting corrosion of different positions (Top, Middle and Bottom) of weld nugget zone (WNZ) along thickness plate in friction stir welded 2219-O aluminum alloy in alkaline chloride solution was investigated by using open circuit potential, cyclic polarization, scanning electron microscopy and atomic force microscope. The results indicate that the material presents significant passivation, the top has highest corrosion potential, pitting potential and re-passivation potential compared with the bottom and base material. With the increase of traverse speed from 60 to 100 mm/min or rotary speed from 500 to 600 rpm, the corrosion resistance decreases.

  14. Kinetics of leaching of the aluminum hydroxide in bauxites by alkaline solutions at atmospheric pressure

    Science.gov (United States)

    Burtsev, A. V.; Lainer, Yu. A.; Gorichev, I. G.; Kipriyanov, N. A.; Izotov, A. D.

    2011-11-01

    The kinetics of leaching of the aluminum hydroxide from the gibbsite bauxites of Guinea (Kindia deposit) is studied under atmospheric conditions. The activation energy of the process is found to be 34.75 kJ/mol, which indicates that the process proceeds in a kinetic mode. The leaching of the aluminum hydroxide from bauxite in an alkaline solution is simulated using acid-base equilibria (ion exchange) and the electrochemical theory of the structure of a double electrical layer (Gram-Parsons theory).

  15. EIS ANALYSIS ON THE ANODIC PROCESS OF ZINC IN AN ALKALINE SOLUTION

    Institute of Scientific and Technical Information of China (English)

    Y. Zheng; J.M. Wang; H. Chen; J.Q. Zhang; C.N. Cao

    2004-01-01

    The EIS on the anodic process of pure Zn in an alkaline solution were performed and fitted using the expression of Faradic admittance, based on which the mechanism of the process was proposed. The results showed that besides electrode potential E the electrochemical reaction rate was affected by the adsorption of Zn(OH)ads on the electrode surface and the diffusion of in the electrolyte in active region, and only by the covering of passivation layer on the electrode surface in both transitive and passivation regions. The equivalent circuits applied in these various circumstances were proposed and the variation of some parameters and state variables was also discussed.

  16. Pitting corrosion of friction stir welded aluminum alloy thick plate in alkaline chloride solution

    International Nuclear Information System (INIS)

    The pitting corrosion of different positions (Top, Middle and Bottom) of weld nugget zone (WNZ) along thickness plate in friction stir welded 2219-O aluminum alloy in alkaline chloride solution was investigated by using open circuit potential, cyclic polarization, scanning electron microscopy and atomic force microscope. The results indicate that the material presents significant passivation, the top has highest corrosion potential, pitting potential and re-passivation potential compared with the bottom and base material. With the increase of traverse speed from 60 to 100 mm/min or rotary speed from 500 to 600 rpm, the corrosion resistance decreases.

  17. Exploration of As(III)/As(V) Uptake from Aqueous Solution by Synthesized Calcium Sulfate Whisker☆

    Institute of Scientific and Technical Information of China (English)

    Xiaojuan Chen; Liuchun Yang; Junfeng Zhang; Yan Huang

    2014-01-01

    Although common calcium-containing minerals such as calcite and gypsum may fix arsenic, the interaction be-tween modified calcic minerals and arsenic has seldom been reported. The uptake behavior of As(III)/As(V) from aqueous solutions by calcium sulfate whisker (CSW, dihydrate or anhydrite) synthesized through a cooling recrystal ization method was explored. A series of batch experiments were conducted to examine the effect of pH, reaction time, whisker dosage, and initial As concentration. X-ray diffraction (XRD) and scanning electron microscopy (SEM) were used to characterize the samples prepared. The results showed that pH of the aqueous solution was an important parameter for As(III)/As(V) uptake, and an excellent removal efficiency could be achieved under strongly alkaline condition. The data from batch experiments for reaction of As(V) with calcium sulfate dihydrate whisker (CSDW) and calcium sulfate anhydrous whisker (CSAW) were well described with extended Langmuir EXT1 model, from which theoretic maximum adsorption capacity of 46.57 mg As(V)·(g CSDW)−1 and 39.18 mg As(V)·(g CSAW)−1 were obtained. Some calcium arsenate solids products, such as CaAsO3(OH) (weilite, syn), Ca3(AsO4)2 (calcium arsenate), CaO–As2O5, Ca–As–O, Ca5(AsO4)3OH·xH2O (calcium arsenate hydroxide hydrate), and CaH(AsO4)·2H2O (hydrogen calcium arsenic oxide hydrate), were detected at pH = 12.5 through XRD analysis. This indicates that the interaction mechanism between As(V) and CSW is a complex adsorption process combined with surface dissolution and chemical precipitation.

  18. Micellization properties of cationic gemini surfactants in aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Łudzik, K., E-mail: kasialudzik@tlen.pl [Department of Physical Chemistry, University of Łódź, Pomorska 165, 90-236 Łódź (Poland); Piekarski, H.; Kubalczyk, K.; Wasiak, M. [Department of Physical Chemistry, University of Łódź, Pomorska 165, 90-236 Łódź (Poland)

    2013-04-20

    Highlights: ► We measured the d and c{sub p} of for the aqueous solutions of 8-6-8 and 8-12-8 surfactants. ► We analyzed the α{sub T} = f (m), V{sub ϕ} = f (m), c{sub p} = f (m) and C{sub p,ϕ} = f (m). ► The inflection point in the curves of the C{sub p,ϕ} = f (m) corresponds to the c.m.c. ► We analyzed thermodynamics parameters of the micellization for the surfactants. - Abstract: The main goal of this work was to investigate the self-assembly process for water solutions of two gemini surfactants, which differ in spacer chain length, at wide range of temperatures. For this reason the aqueous solutions of hexylene-1,6-bis(dimethyl-octylammonium bromide) and dodecylene-1,12-bis(dimethyloctylammonium bromide) have been examined by the calorimetric (DSC) and densimetric methods within the 293–323 K and 288–323 K temperature range, respectively. The analysis of c{sub p} values obtained for the examined systems allowed to propose an alternative way to estimate the region where micellization process can occur. The observed temperature dependence of the c.m.c. for surfactants investigated shows a typical shape for ionic gemini surfactants. This behavior was explained as a resultant of two competing effect: decrease in the hydrophilic properties of the surfactant molecule and decrease in the hydrophobic hydration of the alkyl chain along with the temperature increase. The enthalpy of micellization ΔH{sub mic} and other thermodynamics parameters associated with the micellization process: ΔG{sub mic}, ΔS{sub mic} and ΔC{sub p} {sub mic} were calculated on the base of the pseudo-phase separation model. As expected, more exothermic enthalpies of micellization are observed with increasing temperature for both the surfactants investigated in this work.

  19. Electrosorption of inorganic salts from aqueous solution using carbon aerogels.

    Science.gov (United States)

    Gabelich, Christopher J; Tran, Tri D; Suffet, I H Mel

    2002-07-01

    Capacitive deionization (CDI) with carbon aerogels has been shown to remove various inorganic species from aqueous solutions, though no studies have shown the electrosorption behavior of multisolute systems in which ions compete for limited surface area. Several experiments were conducted to determine the ion removal capacity and selectivity of carbon aerogel electrodes, using both laboratory and natural waters. Although carbon aerogel electrodes have been treated as electrical double-layer capacitors, this study showed that ion sorption followed a Langmuir isotherm, indicating monolayer adsorption. The sorption capacity of carbon aerogel electrodes was approximately 1.0-2.0 x 10(-4) equiv/g aerogel, with ion selectivity being based on ionic hydrated radius. Monovalent ions (e.g., sodium) with smaller hydrated radii were preferentially removed from solution over multivalent ions (e.g., calcium) on a percent or molar basis. Because of the relatively small average pore size (4-9 nm) of the carbon aerogel material, only 14-42 m2/g aerogel surface area was available for ion sorption. Natural organic matter may foul the aerogel surface and limit CDI effectiveness in treating natural waters. PMID:12144279

  20. Structure and phase behavior of aqueous methylcellulose solutions

    Science.gov (United States)

    McAllister, John; Schmidt, Peter; Lodge, Timothy; Bates, Frank

    2015-03-01

    Cellulose ethers (CE) constitute a multi-billion dollar industry, and have found end uses in a broad array of applications from construction materials, food products, personal care products, and pharmaceuticals for more than 80 years. Methylcellulose (MC, with the trade name METHOCEL™) is a CE in which there is a partial substitution of -OH groups with -OCH3 groups. This results in a polymer that is water-soluble at low temperatures, and aqueous solutions of MC display gelation and phase separation at higher temperatures. The nature of MC gelation has been debated for many years, and this project has made significant advances in the understanding of the solution properties of CEs. We have characterized a fibrillar structure of MC gels by cryogenic transmission electron microscopy (cryo-TEM) and small angle neutron scattering (SANS). Using light scattering, turbidity measurements, and dynamic mechanical spectroscopy (DMS) we report that MC microphase separates by nucleation and growth of fibril aggregates, and is a different process from LCST phase separation.

  1. Photocatalytic decomposition of cortisone acetate in aqueous solution.

    Science.gov (United States)

    Romão, Joana Sobral; Hamdy, Mohamed S; Mul, Guido; Baltrusaitis, Jonas

    2015-01-23

    The photocatalytic decomposition of cortisone 21-acetate (CA), a model compound for the commonly used steroid, cortisone, was studied. CA was photocatalytically decomposed in a slurry reactor with the initial rates between 0.11 and 0.46 mg L(-1)min(-1) at 10 mg L(-1) concentration, using the following heterogeneous photocatalysts in decreasing order of their catalytic activity: ZnO>Evonik TiO2 P25>Hombikat TiO2>WO3. Due to the lack of ZnO stability in aqueous solutions, TiO2 P25 was chosen for further experiments. The decomposition reaction was found to be pseudo-first order and the rate constant decreased as a function of increasing initial CA concentration. Changing the initial pH of the CA solution did not affect the reaction rate significantly. The decomposition reaction in the presence of the oxidizing sacrificial agent sodium persulfate showed an observed decomposition rate constant of 0.004 min(-1), lower than that obtained for TiO2 P25 (0.040 min(-1)). The highest photocatalytic degradation rate constant was obtained combining both TiO2 P25 and S2O8(2-) (0.071 min(-1)) showing a synergistic effect. No reactive intermediates were detected using LC-MS showing fast photocatalytic decomposition kinetics of CA. PMID:24953705

  2. Characterization of Chitin and Chitosan Molecular Structure in Aqueous Solution

    Energy Technology Data Exchange (ETDEWEB)

    Franca, Eduardo D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Lins, Roberto D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Freitas, Luiz C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Straatsma, t. P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2008-11-08

    Molecular dynamics simulations have been used to characterize the structure of chitin and chitosan fibers in aqueous solutions. Chitin fibers, whether isolated or in the form of a β-chitin nanoparticle, adopt the so-called 2-fold helix with Φ and φ values similar to its crystalline state. In solution, the intramolecular hydrogen bond HO3(n)•••O5(n+1) responsible for the 2-fold helical motif is stabilized by hydrogen bonds with water molecules in a well-defined orientation. On the other hand, chitosan can adopt five distinct helical motifs and its conformational equilibrium is highly dependent on pH. The hydrogen bond pattern and solvation around the O3 atom of insoluble chitosan (basic pH) are nearly identical to these quantities in chitin. Our findings suggest that the solubility and conformation of these polysaccharides are related to the stability of the intrachain HO3(n)•••O5(n+1) hydrogen bond, which is affect by the water exchange around the O3-HO3 hydroxyl group.

  3. Speciation of aluminum in aqueous solutions using ion chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Bertsch, P.M.; Anderson, M.A.

    1989-03-15

    An ion chromatographic method in which aluminum (AI) is quantitatively determined via postcolumn derivatization with Tiron (4,5-dihydroxy-m-benzenedisulfonic acid) was evaluated for its utility as a method for speciating AI in aqueous solutions. Fluro-, oxalato-, and citratoaluminum complexes were identified by distinct peaks within chromatograms of AI solutions when the appropriate ligand was added. Excellent quantitative agreement between predicted species concentrations (via the thermodynamic speciation model GEOCHEM) and those determined by ion chromatography was obtained for samples prepared in the eluent matrix. The predominantly outer sphere sulfatoaluminum complexes were not observed to elute as singly charged species, but rather exhibited a retention time indistinguishable from the AI(H/sub 2/O)6(3+) species. It is concluded that inner sphere AI complexes (generally possessing relatively high association constants) possess adequate kinetic stability to withstand degradation during the ion exchange process, whereas outer sphere complexes apparently readily dissociate in the presence of the sulfonate exchange sites. Deviations in sample ionic strength (mu) and pH from that of the eluent resulted in some redistribution among species, the degree of which was ligand specific.

  4. Hydroxyl radical induced degradation of salicylates in aerated aqueous solution

    International Nuclear Information System (INIS)

    Ionizing radiation induced degradation of acetylsalicylic acid, its hydrolysis product salicylic acid and a salicylic acid derivative 5-sulpho-salicylic acid, was investigated in dilute aqueous solutions by UV–vis spectrophotometry, HPLC separation and diode-array or MS/MS detection, chemical oxygen demand, total organic carbon content and by Vibrio fischeri toxicity measurements. Hydroxyl radicals were shown to degrade these molecules readily, and first degradation products were hydroxylated derivatives in all cases. Due to the by-products, among them hydrogen peroxide, the toxicity first increased and then decreased with the absorbed dose. With prolonged irradiation complete mineralization was achieved. - Highlights: • In OH induced reactions of salicylates first products are hydroxylated derivatives. • With prolonged irradiation dihydroxy derivatives also form. • In aerated solutions the one-electron oxidant OH induces 3–4 oxidations. • Toxicity first increases and then decreases with dose mainly due to H2O2 formation. • The toxicity in tap water is smaller than in pure water

  5. Removal of Nitrate From Aqueous Solution Using Rice Chaff

    Directory of Open Access Journals (Sweden)

    Dehghani

    2015-09-01

    Full Text Available Background Nitrate is largely dissolved in the surface and ground water, due to its high solubility. Continual uptake of nitrite through drinking water can lead to problems and diseases (such as blue baby for humans, especially children. Objectives The aim of this study was to develop a new and inexpensive method for the removal of nitrate from water. In this regard, the possibility of using chaff for removal of nitrate from aqueous solutions was studied and the optimum operating conditions of nitrate removal was determined. Materials and Methods This is a cross-sectional study conducted in laboratory scale. The UV spectrophotometer at a wavelength of maximum absorbance (220 nm was used to determine the nitrate concentration. The effect of pH, amount of chaff, temperature, and contact time were investigated. Results The result of this study revealed that chaff as an absorbent could remove nitrate from solutions, and the efficiency of adsorption increased as contact time increased from 5 to 30 minutes, amount of chaff increased from 1 to 3 g, temperature increased in a range of 300 - 400°C and the amount of pH decreased from 10 to 3. The maximum adsorption rate was around pH 3 (53.14%. Conclusions It was shown that the removal efficiency of nitrate was directly proportional to the amount of chaff, temperature, and contact time but inversely to the pH. This study showed that nitrate removal by chaff is a promising technique.

  6. Adsorption of itaconic acid from aqueous solutions onto alumina

    Directory of Open Access Journals (Sweden)

    JELENA J. GULICOVSKI

    2008-08-01

    Full Text Available Itaconic acid, IA (C5H6O4, was investigated as a potential flocculant for the aqueous processing of alumina powders. The adsorption of IA, as a function of its concentration and pH value of the solution, onto the alumina surface was studied by the solution depletion method. The stability of the suspensions in the presence of itaconic acid was evaluated in light of the surface charge of the alumina powder used, the degree of dissociation of IA, as well as the sedimentation behavior and rheology of the suspensions. It was found that the adsorption process is extremely pH dependent; the maximum adsorption of IA onto alumina surface occurring at a pH close to the value of the first IA dissociation constant, pKa1. Also, IA does not influence the value of the point of zero charge of alumina. It was shown that IA represents an efficient flocculant for concentrated acidic alumina suspensions.

  7. Single Molecule Electrochemical Detection in Aqueous Solutions and Ionic Liquids.

    Science.gov (United States)

    Byers, Joshua C; Paulose Nadappuram, Binoy; Perry, David; McKelvey, Kim; Colburn, Alex W; Unwin, Patrick R

    2015-10-20

    Single molecule electrochemical detection (SMED) is an extremely challenging aspect of electroanalytical chemistry, requiring unconventional electrochemical cells and measurements. Here, SMED is reported using a "quad-probe" (four-channel probe) pipet cell, fabricated by depositing carbon pyrolytically into two diagonally opposite barrels of a laser-pulled quartz quadruple-barreled pipet and filling the open channels with electrolyte solution, and quasi-reference counter electrodes. A meniscus forms at the end of the probe covering the two working electrodes and is brought into contact with a substrate working electrode surface. In this way, a nanogap cell is produced whereby the two carbon electrodes in the pipet can be used to promote redox cycling of an individual molecule with the substrate. Anticorrelated currents generated at the substrate and tip electrodes, at particular distances (typically tens of nanometers), are consistent with the detection of single molecules. The low background noise realized in this droplet format opens up new opportunities in single molecule electrochemistry, including the use of ionic liquids, as well as aqueous solution, and the quantitative assessment and analysis of factors influencing redox cycling currents, due to a precisely known gap size. PMID:26398675

  8. Columnar molecular aggregation in the aqueous solutions of disodium cromoglycate

    Science.gov (United States)

    Agra-Kooijman, Dena M.; Singh, Gautam; Lorenz, Alexander; Collings, Peter J.; Kitzerow, Heinz-S.; Kumar, Satyendra

    2014-06-01

    Stack, chimneylike, and threadlike assemblies have previously been proposed for the structure of disodium cromoglycate (DSCG) aggregates in aqueous solutions. The results of the synchrotron x-ray scattering investigations reported here reveal the formation of simple columnar assemblies with π-π stacking at a separation of 3.4 Å between the DSCG molecules. Lateral separation between the assemblies is concentration and temperature dependent, varying from ˜35 to 42 Å in the orientationally ordered nematic (N) phase and from 27 to 32 Å in the columnar or middle (M) phase having long range lateral positional order. The assemblies' length depends on concentration and consists of ˜23 molecules in the N phase, becoming three to ten times larger in the M phase. The scission energy is concentration dependent in the N phase with values ˜7.19 ± 0.14 kBT (15 wt %), 2.73 ± 0.4 kBT (20 wt %), and 3.05 ± 0.2 kBT (25 wt %). Solutions of all concentrations undergo a spinodal decomposition at temperatures above ˜40 °C, resulting in DSCG-rich regions with the M phase and water-rich regions in the N and isotropic phases.

  9. Cast iron deterioration with time in various aqueous salt solutions

    Indian Academy of Sciences (India)

    Rita Mehra; Aditi Soni

    2002-02-01

    The changes with time in the corrosion rate and corrosion current density on a cast iron electrode in various aqueous salt solutions have been carried out using total immersion test and potentiostatic polarization curves. The concentration of salts taken is expected to be present in potable water. The relative behaviour of these salts towards corrosion has also been studied, which is found to be different from previous studies. The total immersion test parameters viz. weight loss, corrosion rate as well as potentiostatic parameters, open circuit potential, corr, Tafel slopes, corrosion rate, have been calculated by standard methods. Besides these the relative increase in corrosion rate with time as well as the percentage to which corrosion rate should be decreased so as to provide protection towards corrosion have also been calculated. It was found that KCl and NaCl are major contributors than MnSO4, Pb(NO3)2, KI and KBr. The relative increase in corrosion is high in KBr, KI, NaNO3, CaCl2, and less in Pb(NO3)2, NaHCO3 and CaCO3 test solutions. For the reliability of results the data has been statistically analysed.

  10. Degradation of 2-mercaptobenzothiazole in aqueous solution by gamma irradiation

    Science.gov (United States)

    Bao, Qiburi; Chen, Lujun; Tian, Jinping; Wang, Jianlong

    2014-10-01

    Industrial wastewaters containing 2-mercaptobenzothiazole (MBT), a widely used chemical additive, usually cannot be treated properly by conventional biological methods, thus cause an environmental risk. Ionizing radiation was proposed as a method for abatement of several refractory pollutants from water. The paper investigated MBT degradation using irradiation technology. The decomposition kinetics was described, and the transformation and the change of biodegradability were discussed. The results of gamma radiation experiments on MBT-containing aqueous solutions indicated that reactive radicals resulting from water radiolysis effectively degrade MBT and improve the biodegradability of the solutions. At a 20 mg/L MBT concentration, the removal of 82% was achieved at the absorbed dose of 1.2 kGy. The results of specific oxygen uptake rate (SOUR) test showed that MBT was decomposed into biodegradable products, after irradiation at 20 kGy. Radicals attacked the sulfur atoms of the studied molecule leading to the release of sulfate ions, but the mineralization of organic carbons was rather weak. Initial concentration significantly affected the degradation efficacy of MBT by gamma radiation.

  11. Preparation, characterization and application of alkaline leached CuNiZn ternary coatings for long-term electrolysis in alkaline solution

    Energy Technology Data Exchange (ETDEWEB)

    Solmaz, Ramazan [Bingoel University, Science and Letters Faculty, Chemistry Department, 12000 Bingoel (Turkey); Doener, Ali; Kardas, Guelfeza [Cukurova University, Science and Letters Faculty, Chemistry Department, 01330 Balcali Adana (Turkey)

    2010-10-15

    The NiCuZn ternary coating was electrochemically deposited on a copper electrode. Then, it was etched in a concentrated alkaline solution (30% NaOH) to produce a porous and electrocatalytic surface suitable for use in the hydrogen evolution reaction (HER). The surface composition of coating before and after alkaline leaching was determined by energy dispersive X-ray (EDX) analysis. The surface morphologies were investigated by scanning electron microscopy (SEM). The long-term stability of electrode prepared for alkaline water electrolysis was investigated in 1 M KOH solution with the help of cathodic current-potential curves and electrochemical impedance spectroscopy (EIS) techniques. It was found that, the NiCuZn coating has a compact and porous structure with good physical stability. Alkaline leaching process further improved the activity of NiCuZn coating in comparison with binary NiCu deposit for the HER. The long-term operation at -100 mA cm{sup -2} showed good electrochemical stability over 120 h. (author)

  12. Interaction of gypsum with lead in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Astilleros, J.M., E-mail: jmastill@geo.ucm.es [Dpto. Cristalografia y Mineralogia, Universidad Complutense de Madrid, Jose Antonio Novais, 2, E-28040 Madrid (Spain); Godelitsas, A. [Department of Mineralogy and Petrology, Faculty of Geology and Geoenvironment, University of Athens, Panepistimioupoli Zographou, 15784 Athens (Greece); Rodriguez-Blanco, J.D. [School of Earth and Environments, Faculty of Environment, University of Leeds, Leeds LS2 9JT (United Kingdom); Fernandez-Diaz, L. [Dpto. Cristalografia y Mineralogia, Universidad Complutense de Madrid, Jose Antonio Novais, 2, E-28040 Madrid (Spain); Prieto, M. [Dpto. de Geologia, Universidad de Oviedo, E-30005 Oviedo (Spain); Lagoyannis, A.; Harissopulos, S. [Tandem Accelerator Laboratory, Institute of Nuclear Physics, NCSR ' Demokritos' , GR-15310 Attiki (Greece)

    2010-07-15

    Sorption processes on mineral surfaces are a critical factor in controlling the distribution and accumulation of potentially harmful metals in the environment. This work investigates the effectiveness of gypsum (CaSO{sub 4}.2H{sub 2}O) to sequester Pb. The interaction of gypsum fragments with Pb-bearing solutions (10, 100 and 1000 mg/L) was monitored by performing macroscopic batch-type experiments conducted at room temperature. The aqueous phase composition was periodically determined by Atomic Absorption Spectrometry (AAS), Ion Chromatography (IC) and Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). Regardless of the [Pb{sub aq}]{sub initial}, a [Pb{sub aq}]{sub final} < 4 mg/L was always reached. The uptake process was fast (t < 1 h) for [Pb{sub aq}]{sub initial} {>=} 100 mg/L and significantly slower (t > 1 week) for [Pb{sub aq}]{sub initial} = 10 mg/L. Speciation calculations revealed that after a long time of interaction (1 month), all the solutions reached equilibrium with respect to both gypsum and anglesite. For [Pb{sub aq}]{sub initial} {>=} 100 mg/L, sorption takes place mainly via the rapid dissolution of gypsum and the simultaneous formation of anglesite both on the gypsum surface and in the bulk solution. In the case of [Pb{sub aq}]{sub initial} = 10 mg/L, no anglesite precipitation was observed, but surface spectroscopy (proton Rutherford Backscattering Spectroscopy, p-RBS) confirmed the formation of Pb-bearing surface layers on the (0 1 0) gypsum surface in this case also. This study shows that the surface of gypsum can play an important role in the attenuation of Pb in contaminated waters.

  13. The reducibility of sulphuric acid and sulphate in aqueous solution

    International Nuclear Information System (INIS)

    In connection with the Swedish project for final storage of spent fuel elements it was necessary to assess whether dissolved sulphate can corrode the copper canister. A simple reaction between copper and sulphate is thermodynamically impossible, but copper can react to give copper sulphide if an additional electron donor such as iron(II) is available. The problem was extended to the more general question of the reducibility of sulphur(VI) in dilute aqueous solution. Chemical reduction of sulphate does not take place in dilute solution at temperatures below 100oC. In experiments on the reduction of sulphates under hydrothermal conditions a reaction only takes place at temperatures above 275-300oC. The oxidising action of sulphuric acid on metals becomes perceptible only at acid concentrations over 45-50%. In experiments on the cathodic reduction of 74% sulphuric acid the formation of hydrogen sulphide and elementary sulphur starts, depending on the current density, at 50-130oC, and polarographic measurements suggest that the reducible species is not the hydrogen sulphate ion but molecular sulphuric acid. The resistance of copper to oxygen-free sulphuric acid up to a concentration of 60% is well-known. Numerous processes in industrial electrochemistry take place in sulphuric acid or sulphate electrolytes. The reversible metal/metal-sulphate electrodes of lead and cadmium are unstable relative to the corresponding metal sulphides. Nevertheless the reversible lead sulphate electrode does not fail from sulphide formation. All these facts confirm that sulphur(VI) in dilute solution is completely inert towards chemical reducing agents and also to cathodic reduction. Thus corrosion of copper by sulphate under final-storage conditions and in the absence of sulphate reducing bacteria can be almost certainly be ruled out. (author) 5 figs., 85 refs

  14. Poorly crystalline hydroxyapatite: A novel adsorbent for enhanced fulvic acid removal from aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Wei, Wei [Department of Environmental Science and Engineering, Nanjing Normal University, Nanjing 210023 (China); Jiangsu Provincial Key Laboratory of Materials Cycling and Pollution Control, Nanjing Normal University, Nanjing 210023 (China); Jiangsu Center for Collaborative Innovation in Geographical Information Resource Development and Application, Nanjing Normal University, Nanjing 210023 (China); Yang, Lei; Zhong, Wenhui; Cui, Jing [Department of Environmental Science and Engineering, Nanjing Normal University, Nanjing 210023 (China); Wei, Zhenggui, E-mail: weizhenggui@gmail.com [Department of Environmental Science and Engineering, Nanjing Normal University, Nanjing 210023 (China); Jiangsu Provincial Key Laboratory of Materials Cycling and Pollution Control, Nanjing Normal University, Nanjing 210023 (China); Jiangsu Center for Collaborative Innovation in Geographical Information Resource Development and Application, Nanjing Normal University, Nanjing 210023 (China)

    2015-03-30

    Graphical abstract: - Highlights: • Poorly crystalline HAP was firstly used for FA removal from aqueous solution. • The maximum adsorption capacity was determined to be 90.20 mg/g at 318 K. • Adsorption kinetics, isotherms and thermodynamic have been studied in detail. • Adsorption mechanism involved surface complexation, electrostatic interaction and hydrogen bonding. - Abstract: In this study, poorly crystalline hydroxyapatite (HAP) was developed as an efficient adsorbent for the removal of fulvic acid (FA) from aqueous solution. Surface functionality, crystallinity, and morphology of the synthetic adsorbent were studied by Fourier-transformation infrared (FT-IR) spectroscopy, powder X-ray diffraction (XRD) and transmission electron microscopy (TEM). The effects of various parameters such as crystallinity of adsorbent, contact time, adsorbent dosage, pH, initial adsorbate concentration, temperature, ionic strength and the presence of alkaline earth metal ions on FA adsorption were investigated. Results indicated that the nanosized HAP calcined at lower temperature was poorly crystalline (X{sub c} = 0.23) and had better adsorption capacity for FA than those (X{sub c} = 0.52, 0.86) calcined at higher temperature. FA removal was increased with increases of adsorbent dosage, temperature, ionic strength and the presence of alkali earth metal ions, but decreased as the pH increased. Kinetic studies showed that pseudo-second-order kinetic model better described the adsorption process. Equilibrium data were best described by Sips models, and the estimated maximum adsorption capacity of poorly crystalline HAP was 90.20 mg/g at 318 K, displaying higher efficiency for FA removal than previously reported adsorbents. FT-IR results revealed that FA adsorption over the adsorbent could be attributed to the surface complexation between the oxygen atom of functional groups of FA and calcium ions of HAP. Regeneration studies indicated that HAP could be recyclable for a long

  15. Effect of Additional Sulfide and Thiosulfate on Corrosion of Q235 Carbon Steel in Alkaline Solutions

    Directory of Open Access Journals (Sweden)

    Bian Li Quan

    2016-01-01

    Full Text Available This paper investigated the effect of additional sulfide and thiosulfate on Q235 carbon steel corrosion in alkaline solutions. Weight loss method, scanning electron microscopy (SEM equipped with EDS, X-ray photoelectron spectroscopy (XPS, and electrochemical measurements were used in this study to show the corrosion behavior and electrochemistry of Q235 carbon steel. Results indicate that the synergistic corrosion rate of Q235 carbon steel in alkaline solution containing sulfide and thiosulfate is larger than that of sulfide and thiosulfate alone, which could be due to redox reaction of sulfide and thiosulfate. The surface cracks and pitting characteristics of the specimens after corrosion were carefully examined and the corrosion products film is flake grains and defective. The main corrosion products of specimen induced by S2− and S2O32- are FeS, FeS2, Fe3O4, and FeOOH. The present study shows that the corrosion mechanism of S2− and S2O32- is different for the corrosion of Q235 carbon steel.

  16. Sorption properties of hydrous manganese oxide for the removal of radioactive manganese from aqueous solution

    International Nuclear Information System (INIS)

    Radioactive manganese (54Mn) is formed in the structural and clad components of fast nuclear reactors due to the high energy neutron flux encountered in the core. It is a corrosion activation product having a half-life of 312.5 days and gamma energy of 835 keV. Hence, its removal from the waste which generates after washing the above mentioned components is very important. The removal properties of radioactive manganese, 54Mn, from an aqueous solution were studied here in a batch process using hydrous manganese oxide (HMO) coated with polyurethane foam as an inorganic sorbent. The HMO was synthesized by alkaline precipitation in air using manganese sulphate monohydrate and potassium permanganate. The synthesized material was found to be in powder form which took lot of time for settlement in solution; hence, it was coated with polyurethane foam, so that it can be easily used in a batch process. The removal of the radioisotope by the sorbent was studied by varying different experimental conditions such as solution pH, contact time, and effect of presence of other divalent ions. The studies carried out in our laboratory found that the sorption of manganese by hydrous manganese oxide followed pseudo-second order kinetics. On the other hand, with increasing pH of the solution (pH range studied: 1-8), the removal of manganese by the sorbent also increases until pH reaches 4.5, after that the sorption was almost same. The present studies confirmed that in the presence of other divalent ions, e.g. cobalt (ii) ions, the sorption was effected which may be due to the sorption of both the ions on hydrous manganese oxide. The sorption was very fast and more than 95% of manganese was removed within one hour of contact with hydrous manganese oxide. (author)

  17. The photochemical decomposition of Indol in an aqueous solution; Descomposicion fotoquimica de Indol en solucion acuosa

    Energy Technology Data Exchange (ETDEWEB)

    Ibarz, A.; Tejero, J.M.; Panades, R.

    1998-06-01

    The photo decomposition of Indol at different pH has been studied. The Indol photo decomposition rate in aqueous solution a maximum at pH 10. By means of a simple mechanism in three steps, it is possible to explain the kinetics behavior of the Indol photo decomposition in aqueous solution. (Author) 6 refs.

  18. Optical properties of chitosan in aqueous solution of L- and D-ascorbic acids

    Science.gov (United States)

    Malinkina, Olga N.; Shipovskaya, Anna B.; Kazmicheva, Olga F.

    2016-04-01

    The optical properties of aqueous chitosan solutions in L- and D-ascorbic acids were studied by optical rotatory dispersion and spectrophotometry. The specific optical rotation [α] of all chitosan solutions tested was positive, in contrast to aqueous solutions of the ascorbic acid enantiomers, which exhibit an inverse relationship of [α] values. Significant differences in the absolute values of [α] of the chitosan solutions at polymer-acid ratios exceeding the equimolar one were found.

  19. Removal of uranyl ions from aqueous solutions using barium titanate

    International Nuclear Information System (INIS)

    Remediation of water sources contaminated with radioactive waste products is a major environmental issue that demands new and more efficient technologies. For this purpose, we report a highly efficient ion-exchange material for the removal of radioactive nuclides from aqueous solutions. The kinetic characteristics of adsorption of uranyl ions on the surface of barium titanate were investigated using a spectrophotometric method under a wide range of conditions. By controlling the pH it was possible to exert fine control over the speciation of uranium, and by optimizing the temperature and grain size of the exchanger, almost total removal was achieved in a matter of just hours. The highest efficiency (>90 % removal) was realized at high temperature (80 deg C). Moreover, the effect of competitive ion adsorption from a range of different cations and anions was quantified. Adsorption was found to follow first-order kinetics and both Freundlich and Langmuir isotherms could be applied to this system. The results of a mathematical treatment of the kinetic data combined with the observation that adsorption was independent of stirring speed and dependent on the ion-exchanger grain size, indicate that the dominant mechanism influencing adsorption is particle spreading. The adsorption behavior was not influenced by exposure to high-intensity gamma radiation, indicating potential for use of this ion-exchanger in systems containing radioactive material. These results will be of use in the development of uranium extraction systems for contaminated water sources. (author)

  20. Ethylbenzene Removal by Carbon Nanotubes from Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Bijan Bina

    2012-01-01

    Full Text Available The removal of ethylbenzene (E from aqueous solution by multiwalled, single-walled, and hybrid carbon nanotubes (MWCNTs, SWCNTs, and HCNTs was evaluated for a nanomaterial dose of 1 g/L, concentration of 10–100 mg/L, and pH 7. The equilibrium amount removed by SWCNTs (E: 9.98 mg/g was higher than by MWCNTs and HCNTs. Ethylbenzene has a higher adsorption tendency on CNTs, so that more than 98% of it adsorbed in first 14 min, which is related to the low water solubility and the high molecular weight. The SWCNTs performed better for ethylbenzene sorption than the HCNTs and MWCNTs. Isotherms study indicates that the BET isotherm expression provides the best fit for ethylbenzene sorption by SWCNTs. Carbon nanotubes, specially SWCNTs, are efficient and rapid adsorbents for ethylbenzene which possess good potential applications to maintain high-quality water. Therefore, it could be used for cleaning up environmental pollution to prevent ethylbenzene borne diseases.

  1. The evaporation behavior of sessile droplets from aqueous saline solutions.

    Science.gov (United States)

    Soulié, Virginie; Karpitschka, Stefan; Lequien, Florence; Prené, Philippe; Zemb, Thomas; Moehwald, Helmuth; Riegler, Hans

    2015-09-14

    Quantitative experiments on the evaporation from sessile droplets of aqueous saline (NaCl) solutions show a strong dependence on salt concentration and droplet shape. The experiments were performed with seven decades of initial NaCl concentrations, with various droplet sizes and with different contact angles. The evaporation rate is significantly lower for high salt concentrations and small contact angles than what is expected from the well-accepted diffusion-controlled evaporation scenario for sessile droplets, even if the change of the vapor pressure due to the salt is taken into account. Particle tracking velocimetry reveals that this modification of the evaporation behavior is caused by marangoni flows that are induced by surface tension gradients originating from the local evaporative peripheral salt enrichment. In addition it is found that already very low salt concentrations lead to a pinning of the three phase contact line. Whereas droplets with concentration ≥10(-6) M NaCl are pinned as soon as evaporation starts, droplets with lower salt concentration do evaporate in a constant contact angle mode. Aside from new, fundamental insights the findings are also relevant for a better understanding of the widespread phenomenon of corrosion initiated by sessile droplets.

  2. Uranium biosorption from aqueous solution onto Eichhornia crassipes.

    Science.gov (United States)

    Yi, Zheng-ji; Yao, Jun; Chen, Hui-lun; Wang, Fei; Yuan, Zhi-min; Liu, Xing

    2016-04-01

    Batch experiments were conducted to investigate the biosorption of U(VI) from aqueous solutions onto the nonliving biomass of an aquatic macrophyte Eichhornia crassipes. The results showed that the adsorption of U(VI) onto E. crassipes was highly pH-dependent and the best pH for U(VI) removal was 5.5. U(VI) adsorption proceeded rapidly with an equilibrium time of 30 min and conformed to pseudo-second-order kinetics. The Langmuir isotherm model was determined to best describe U(VI) biosorption with a maximum monolayer adsorption capacity of 142.85 mg/g. Thermodynamic calculation results indicated that the U(VI) biosorption process was spontaneous and endothermic. Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy analysis implied that the functional groups (amino, hydroxyl, and carboxyl) may be responsible for the U(VI) adsorption process, in which the coordination and ion exchange mechanisms could be involved. We conclude that E. crassipes biomass is a promising biosorbent for the removal of uranium pollutants. PMID:26854553

  3. Biosorption of carbaryl from aqueous solution onto Pistia stratiotes biomass

    Science.gov (United States)

    Chattoraj, Soumya; Mondal, Naba Kumar; Das, Biswajit; Roy, Palas; Sadhukhan, Bikash

    2014-03-01

    In this work, adsorption of carbaryl from aqueous solution on Pistia stratiotes biomass was investigated. The effects of operating parameters such as initial concentration, pH, adsorbent dose and contact time on the adsorption of carbaryl were analyzed using response surface methodology. The proposed quadratic model for central composite design fitted very well to the experimental data that it could be used to navigate the design space according to analysis of variance results. Response surface plots were used to determine the interaction effects of main factors and optimum conditions of the process. The optimum adsorption conditions were found to be initial carbaryl concentration = 15.57 mg L-1, pH 2.01, adsorbent dose = 0.72 g and contact time = 30 min. The Langmuir, Freundlich and Temkin isotherm models were applied to the equilibrium data. The maximum biosorption capacity of P. stratiotes biomass for carbaryl was found to be 3.1 mg g-1. The pseudo-second-order kinetic model described the carbaryl biosorption process with a good fitting.

  4. Lifetimes of -halo and -azidobenzyl carbocations in aqueous solution

    Indian Academy of Sciences (India)

    R Sanjeev; V Jagannadham

    2002-02-01

    The title cations were produced in aqueous solution by chemical initiation (solvolysis) of benzyl-gem-dihalides and benzyl-gem-diazides. The solvolysis reactions of benzyl-gem-dihalides and benzyl-gem-diazides in water proceed by a stepwise mechanism through -halobenzyl carbocation and -azidobenzyl carbocation intermediates, which are captured by water to give the corresponding carbonyl compounds as the sole detectable products. Rate constant ratio / (M-1) for partitioning of the carbocation between reaction with halide/azide ion and reaction with water is determined by analysis of halide/azide common ion inhibition of the solvolysis reaction. The rate constants (s-1) for the reaction of the cation with solvent water were determined from the experimental values of / and solv, for the solvolysis of the benzyl-gem-dihalides and benzyl-gem-diazides respectively, using = 5 × 109 M-1 s-1 for diffusion-limited reaction of halide/azide ion with -substituted benzyl carbocations. The values of 1/ are thus the lifetimes of the -halobenzyl carbocations and -azidobenzyl carbocations respectively.

  5. Direct Photolysis of Chlorophenols In Aqueous Solution By Ultraviolet Excilamps

    Science.gov (United States)

    Matafonova, Galina; Philippova, Natalya; Batoev, Valeriy

    2011-08-01

    The direct photolysis of 2-chlorophenol (2-CP), 4-chlorophenol (4-CP) and 2,4-dichlorophenol (2,4-DCP) in model aqueous solution was studied using UV XeBr (282 nm) and KrCl (222 nm) excilamps. The highest pseudo-first order rate constants and quantum yields were found for molecular form of 4-CP (at pH 2 and 5.7) and anionic forms of 2-CP and 2,4-DCP (at pH 11) when irradiated by XeBr excilamp. The maximum removal efficiency of molecular form of 2-CP and 2,4-DCP with the lowest UV dose of absorbed energy was observed using KrCl excilamp. On the contrary, the XeBr excilamp required the lowest dose (˜2 Jṡcm-2) for complete degradation of molecular 4-CP and anionic 2-CP. The highest removal efficiency of anionic form of 4-CP (65%) was achieved when using KrCl excilamp.

  6. Electrochemical degradation of amaranth aqueous solution on ACF.

    Science.gov (United States)

    Fan, Li; Zhou, Yanwei; Yang, Weishen; Chen, Guohua; Yang, Fenglin

    2006-09-21

    The degradation of Amaranth, a kind of azo dye, has been studied under galvanostatic model with activated carbon fiber (ACF) electrode in aqueous solution with electrochemical method. The ACF was used as anode and cathode, respectively for the decolorization process. The onset oxidation potential and reduction potential for Amaranth on ACF were respectively ascertained at 0.6 and -0.4 V. During the range of -1.1 to 0.50 mA cm(-2), the decolorization was clarified into three processes as electroreduction, adsorption and electrooxidation. There were little contributions to the color and COD removals for the process of adsorption. The color removal can be up to 99% when the current density was 0.50 mA cm(-2). The maximum COD removal was 52% for the process of electrooxidation. Hundred percent color removal was obtained when the current density of -1.0 mA cm(-2) was applied. The maximum COD removal was 62% for the electroreduction. The COD removal results from the adsorption of products for the decolorization process of electrooxidation or electroreduction.

  7. Defluoridation from aqueous solutions by granular ferric hydroxide (GFH).

    Science.gov (United States)

    Kumar, Eva; Bhatnagar, Amit; Ji, Minkyu; Jung, Woosik; Lee, Sang-Hun; Kim, Sun-Joon; Lee, Giehyeon; Song, Hocheol; Choi, Jae-Young; Yang, Jung-Seok; Jeon, Byong-Hun

    2009-02-01

    This research was undertaken to evaluate the feasibility of granular ferric hydroxide (GFH) for fluoride removal from aqueous solutions. Batch experiments were performed to study the influence of various experimental parameters such as contact time (1 min-24h), initial fluoride concentration (1-100 mgL(-1)), temperature (10 and 25 degrees C), pH (3-12) and the presence of competing anions on the adsorption of fluoride on GFH. Kinetic data revealed that the uptake rate of fluoride was rapid in the beginning and 95% adsorption was completed within 10 min and equilibrium was achieved within 60 min. The sorption process was well explained with pseudo-first-order and pore diffusion models. The maximum adsorption capacity of GFH for fluoride removal was 7.0 mgg(-1). The adsorption was found to be an endothermic process and data conform to Langmuir model. The optimum fluoride removal was observed between pH ranges of 4-8. The fluoride adsorption was decreased in the presence of phosphate followed by carbonate and sulphate. Results from this study demonstrated potential utility of GFH that could be developed into a viable technology for fluoride removal from drinking water.

  8. Pulse radiolysis study of 5-amino tetrazole in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Dey, G.R.; Naik, D.B.; Kishore, K.; Moorthy, P.N. [Bhabha Atomic Research Centre, Bombay (India). Chemistry Div.

    1996-04-01

    Reactions of e{sub aq}{sup -}, H-atoms and {sup .}OH radicals have been studied with 5-amino tetrazole (ATZ) in aqueous solution. e{sub aq}{sup -}reaction in the pH range 4.5-9 did not give any light absorbing transient species but NH{sub 3} was obtained as a product indicating that the site for e{sub aq}{sup -} reactions is the -NH{sub 2} group. In the case of {sup .}OH radical reaction, a transient spectrum with {lambda}{sub max} at 340 nm was obtained at pH 7.5. An identical spectrum was produced by the reaction of SO{sub 4}{sup -.} radicals with ATZ at neutral pH indicating that both {sup .}OH radical and SO{sub 4}{sup -.} radical react by one electron oxidation. The rate constants for the reactions of e{sub aq}{sup -} and {sup .}OH with ATZ at pH 7.5 were found to be 6 x 10{sup 7} and 5.2 x 10{sup 9} dm{sup 3} mol{sup -1} s{sup -1} respectively, whereas the rate constant for H-atom reaction may be < 10{sup 7} dm{sup 3} mol{sup -1} s{sup -1}. (author).

  9. Sonochemical degradation of organophosphorus pesticide in dilute aqueous solutions

    Institute of Scientific and Technical Information of China (English)

    Robina Farooq; FENG Kai-lin; S. F. Shaukat; HUANG Jian-jun

    2003-01-01

    Ultrasonic irradiation was found to accelerate the rate of hydrolysis of omethoate in aqueous solution over the pH range of 2-12. Process parameters studied include pH, steady-state temperature, concentration, and the type of gases. Greater than 96% hydrolysis was observed in 30 minutes through this process and the rate of destruction increased with the help of more soluble and low thermal inert gas. So with Krypton, omethoate was found to undergo rapid destruction as compared with Argon. In the presence of ultrasound, the observed first-order rate of hydrolysis of omethoate is found to be independent of pH. The formation of transient supercritical water(SCW) appears to be an important factor in the acceleration of chemical reactions in the presence of ultrasound. A detailed chemical reaction mechanism for omethoate destruction in water was formulated. Experimental results and theoretical kinetic mechanism demonstrated that the most of the omethoate undergo destruction inside the cavitating holes. A very less effect of temperature on the degradation of omethoate within a temperature range of 20-70℃ proves that a small quantity of omethoate undergoes secondary destruction in the bulk liquid.

  10. Fenton Oxidation of Methyl Violet in Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Saeedeh Hashemian

    2013-01-01

    Full Text Available In this study, oxidative discoloration of methyl violet (MV dye in aqueous solution has been studied using Fenton (Fe2+/H2O2 process. The parameters such as concentration of Fe2+, H2O2, MV, temperature, and Cl− and ions that affected of discoloration in Fenton process were investigated. The rate of degradation is dependent on initial concentration of Fe2+ ion, initial concentration of H2O2, and pH of media. Discoloration of MV was increased by increasing the temperature of reaction. Optimized condition was determined and it was found that the obtained efficiency was about 95.5% after 15 minutes of reaction at pH 3. TOC of dye sample, before and after the oxidation process, was determined. TOC removal indicates partial and significant mineralization of MV dye. The results of experiments showed that degradation of MV dye in Fenton oxidation can be described with a pseudo-irst-order kinetic model. The thermodynamic constants of the Fenton oxidation process were evaluated. The results implied that the oxidation process was feasible, spontaneous, and endothermic.

  11. Photo- and thermal degradation of piroxicam in aqueous solution

    Directory of Open Access Journals (Sweden)

    M Aminuddin

    2011-01-01

    Full Text Available Light and temperature have considerable effect on the degradation of piroxicam in aqueous solutions. The pH and acetate buffer ions also affect the degradation process. The apparent first-order rate constants for the photochemical and thermal degradation of piroxicam have been determined as 2.04-10.01 and 0.86-3.06×10−3 min−1 , respectively. The first-order plots for the degradation of piroxicam showed good linearity within a range of 20-50% loss of piroxicam at pH 2.0-12.0. The rate-pH profile for the photodegradation of piroxicam is a U-shaped curve and for the thermal degradation a bell-shaped curve in the pH range of 2.0-12.0. The thermal degradation of piroxicam was maximum around pH 6.0. It is increased in the presence of acetate ions but was not affected by citrate and phosphate ions.

  12. A vibrational spectroscopy study on anserine and its aqueous solutions.

    Science.gov (United States)

    Akkaya, Y; Balci, K; Goren, Y; Akyuz, S; Stricker, M C; Stover, D D; Ritzhaupt, G; Collier, W B

    2015-01-01

    In this study based on vibrational spectroscopic measurements and Density Functional Theory (DFT), we aimed for a reliable interpretation of the IR and Raman spectra recorded for anserine in the solid phase and water (H2O) and heavy water (D2O) solutions. Initial DFT calculations at the B3LYP/6-31G(d) searched possible conformers of the anserine zwitterion using a systematic conformational search. The corresponding equilibrium geometrical parameters and vibrational spectral data were determined for each of the stable conformers (in water) by the geometry optimization and hessian calculations performed at the same level of theory using the polarized continuum model (PCM). The same calculations were repeated to determine the most energetically preferred dimer structure for the molecule and the associated geometry, force field and vibrational spectral data. The harmonic force constants obtained from these calculations were scaled by the Scaled Quantum Mechanical Force Field (SQM) method and then used in the calculation of the refined wavenumbers, potential energy distributions, IR and Raman intensities. These refined theoretical data, which confirm the zwitterion structure for anserine in the solid phase or aqueous solvents, revealed the remarkable effects of intermolecular hydrogen bonding on the structural properties and observed IR and Raman spectra of this molecule. PMID:25997178

  13. Formation and reactivity of phenylperoxyl radicals in aqueous solutions

    International Nuclear Information System (INIS)

    The reaction of phenyl radicals with oxygen, to produce phenylperoxyl radicals, and the reactions of several phenylperoxyl radicals with a number of organic compounds in aqueous solutions have been studied by pulse radiolysis. Phenyl radicals were produced by reduction of aryl halides with hydrated electrons. The rate constant for the reaction of 4-carboxyphenyl with O2 was determined from the rate of buildup of the peroxyl radical absorption at 520 nm as a function of [O2] and found to be 1.6 x 109 L mol-1 s-1. Phenyl radicals react with 2-PrOH by H abstraction; a rate constants of 4 x 106 L mol-1 s-1 was determined for 4-carboxyphenyl by competition with the reaction of this radical with O2. Phenylperoxyl radicals react with 4-methoxyphenolate ions, trolox C(6-hydroxy-2,5,7,8-tetramethylchroman-2-carboxylic acid), ascorbate ions, chlorpromazine, and ABTS [2,2'-azinobis(3-ethylbenzothiazoline-6-sulfonate ion)] by one-electron oxidation. The rate constants for such reactions, determined from the rate of formation of the one-electron oxidation product as a function of substrate concentration, were found to be near 108-109 L mol-1 s-1. 24 refs., 4 figs., 1 tab

  14. Adsorption removal of thiocyanate from aqueous solution by calcined hydrotalcite

    Institute of Scientific and Technical Information of China (English)

    LI Yu-jiang; YANG Min; ZHANG Xiao-jin; WU Tao; CAO Nan; WEI Na; BI Yan-jun; WANG Jing

    2006-01-01

    A hydrotalcite with Mg/Al molar ratio 2 was prepared by co-precipitation method and was characterized by XRD,TG/DTA, Zeta potential and BET surface area. The hydrotalcite was calcined at 500℃, with the dehydration from interlayer, the dehydroxilation from the brucite-like layer and the decomposition of carbonate successively, transformed into the mixed oxide type.The removal of thiocyanate from aqueous solution by using the original hydrotalcite and calcined hydrotalcite (HTC-500) was investigated. The results showed that the thiocyanate adsorption capacity of calcined hydrotalcite was much higher than that of the original form. Calcined hydrotalcite was particularly effective at removing thiocyanate, and that the effective range of pH for the thiocyanate removal are between 5.5-10.0. The experimental data of thiocyanate removal fit nicely with Langmuir isotherm, and the saturated adsorption uptake was 96.2 mg SCN-/g HTC-500. The adsorption ofthiocyanate by calcined hydrotalcite follows first-order kinetics. And the intercalation to the structure recovery for calcined hydrotalcite. But the presence of additional anions could affect the adsorption behavior of thiocyanate.

  15. Cadmium Removal from Aqueous Solutions by Ground Pine Cone

    Directory of Open Access Journals (Sweden)

    H Izanloo, S Nasseri

    2005-01-01

    Full Text Available A study on the removal of cadmium ions from aqueous solutions by pine cone was conducted in batch conditions. Kinetic data and equilibrium removal isotherms were obtained. The influence of different experimental parameters such as contact time, initial concentration of cadmium, pine cone mass and particle size, and temperature on the kinetics of cadmium removal was studied. Results showed that the main parameters that played an important role in removal phenomenon were initial cadmium concentration, particle size and pine cone mass. The necessary time to reach equilibrium was between 4 and 7 hours based on the initial concentration of cadmium. The capacity of cadmium adsorption at equilibrium increased with the decrease of pine cone particle size. The capacity of cadmium adsorption at equilibrium by pine cone increased with the quantity of pine cone introduced (1–4 g/L. Temperature in the range of 20-30°C showed a restricted effect on the removal kinetics (13.56 mg/g at 20°C and a low capacity of adsorption about 11.48 mg/g at 30°C. The process followed pseudo second-order kinetics. The cadmium uptake of pine cone was quantitatively evaluated using adsorption isotherms. Results indicated that the Langmuir model gave a better fit to the experimental data in comparison with the Freundlich equation.

  16. Alkaline leaching of metal melting industry wastes dseparation of zinc and lead in the leach solution

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    In this work, a thorough examinations on the extractability of zinc and lead present in the steelmaking dusts using alkaline leaching process and the effectiveness of the zinc and lead separation in the resultant leaching solutions using sulfide precipitation method were made. It was found that only about 53% of zinc and over 70% of the lead could be leached out of the dusts, while the other 47% of zinc and 306 of lead were left in the leaching residues. The zinc and lead in the resultant leaching solution can be effectively and selectively separated. When the weight ratio of sodium sulfide (M. W. = 222-240) to Pb was kept at 1.8, the lead in the solution could be precipitated out quantitatively while all the zinc was remained in the solution. The zinc left in the solution can be further recovered by the addition of extra sodium sulfide with a weight ratio of sodium sulfide to the zinc over 2.6. The resultant filtrate can be recycled to the leaching of dust in the next leaching process.

  17. Flash photolysis of chlorine dioxide in aqueous solution

    International Nuclear Information System (INIS)

    The primary process when aqueous solutions of chlorine dioxide are flash photo-lysed by light with a wave length greater than 270 nm is: OClO →hν ClO (2Π) + O (3P). The photochemical decomposition is characterized by the formation of small quantities of O (3P) atoms and of equal amounts of chlorine atoms and molecular oxygen, the latter originating in the reaction: ClOO → Cl + O2. The isomer ClOO is formed by the germinate recombination of ClO and O, a process which is twice as important as diffusion of the fragments into the mass of the solution and one which represents 30 per cent of the decomposition of the chlorine dioxide. Under our experimental conditions, the lifetime of the ClOO is less than one microsecond. Chlorine atoms are precursors of Cl2O2, whose UV absorption spectrum has been determined, and which is formed by the reactions: Cl + OClO → Cl2O2; Cl + Cl- → Cl2-; Cl2- + OClO → Cl2O2 + Cl- k = (1,0 ±0,1) 109 M-1s-1. Cl2O2 disappears by a first-order process which leads to the formation of the ions Cl- and ClO3-. Competition between the reactions: O (3P) + O2 → O3; O (3P) + OClO → ClO3. (kOClO + O)/(kO2 + O) = 1.85±0.25 has been studied and the molar extinction coefficient of ClO3 determined at its absorption maximum (255 nm): ε255nm = (920 ± 90) M-1 cm-1. (author)

  18. Ethylbenzene Removal from Aqueous Solutions by Nano Magnetic Particles

    Directory of Open Access Journals (Sweden)

    Mostafa Hadei

    2016-02-01

    Full Text Available Background and Objectives : Ethylbenzene (EB is a dangerously organic compound which the presence of this pollutant in water solutions can be considered as an environmental and public health hazard. In this study, nano magnetic particles (Fe 3 O 4 were used as an adsorbent to remove ethylbenzene from aqueous solutions. Methods : The specification of the adsorbent was investigated by transmission electronic microscope (TEM and X-ray diffraction (XRD pattern. A 4×4 factorial design including initial concentration of ethylbenzene, nano magnetic particles dose, contact time and pH were studied. Results : The results showed that the maximum ethylbenzene removal by nano magnetic particles was achieved in the following conditions; 100 mg.L -1 , 2000 mg.L -1 , 20 minutes and 8, in initial concentration, nano magnetic concentration, contact time and pH respectively. The most amounts of ethylbenzene adsorption and distribution ratio in optimum condition was 49.9 mg.g -1 and 261.9 l.g -1 respectively. The results demonstrated that the removal rate of ethylbenzene was higher in batch (99.8 % rather than continuous (97.4% condition. Conclusion: the removal rate of ethylbenzene was higher in batch rather than continuous condition.The study of isotherm showed that adsorption data follow up linear isotherm. Comparing adsorption rate of NM particles and other adsorbents proved that Fe 3 o 4 , as a material with high capacity of adsorption can apply for removing ethylbenzene as an efficient and also cheap adsorbent.  

  19. Heavy metal removal from aqueous solutions by activated phosphate rock

    Energy Technology Data Exchange (ETDEWEB)

    Elouear, Z. [Laboratoire Eau Energie et Environnement, Departement de genie geologique, Ecole Nationale d' Ingenieurs de Sfax, BP W 3038, Sfax (Tunisia)], E-mail: zouheir.elouaer@tunet.tn; Bouzid, J.; Boujelben, N. [Laboratoire Eau Energie et Environnement, Departement de genie geologique, Ecole Nationale d' Ingenieurs de Sfax, BP W 3038, Sfax (Tunisia); Feki, M. [Unite de chimie industriel I, Ecole Nationale d' Ingenieurs de Sfax, BP W 3038 Sfax (Tunisia); Jamoussi, F. [Laboratoire de Georessources CERTE BP 95, 2050 Hamam-Lif (Tunisia); Montiel, A. [Societe Anonyme de Gestion des Eaux de Paris, 9 rue Schoelcher, 75675 Paris cedex 14 (France)

    2008-08-15

    The use of natural adsorbent such as phosphate rock to replace expensive imported synthetic adsorbent is particularly appropriate for developing countries such as Tunisia. In this study, the removal characteristics of lead, cadmium, copper and zinc ions from aqueous solution by activated phosphate rock were investigated under various operating variables like contact time, solution pH, initial metal concentration and temperature. The kinetic and the sorption process of these metal ions were compared for phosphate rock (PR) and activated phosphate rock (APR). To accomplish this objective we have: (a) characterized both (PR) and (APR) using different techniques (XRD, IR) and analyses (EDAX, BET-N{sub 2}); and, (b) qualified and quantified the interaction of Pb{sup 2+}, Cd{sup 2+}, Cu{sup 2+} and Zn{sup 2+} with these sorbents through batch experiments. Initial uptake of these metal ions increases with time up to 1 h for (PR) and 2 h for (APR), after then, it reaches equilibrium. The maximum sorption obtained for (PR) and (APR) is between pH 2 and 3 for Pb{sup 2+} and 4 and 6 for Cd{sup 2+}, Cu{sup 2+} and Zn{sup 2+}. The effect of temperature has been carried out at 10, 20 and 40 deg. C. The data obtained from sorption isotherms of metal ions at different temperatures fit to linear form of Langmuir sorption equation. The heat of sorption ({delta}H{sup o}), free energy ({delta}G{sup o}) and change in entropy ({delta}S{sup o}) were calculated. They show that sorption of Pb{sup 2+}, Cd{sup 2+}, Cu{sup 2+} and Zn{sup 2+}on (PR) and (APR) an endothermic process. These findings are significant for future using of (APR) for the removal of heavy metal ions from wastewater under realistic competitive conditions in terms of initial heavy metals, concentrations and pH.

  20. Precipitation of Co(2+) carbonates from aqueous solution: insights on the amorphous to crystalline transformation.

    Science.gov (United States)

    González-López, Jorge; Fernández-González, Ángeles; Jiménez, Amalia

    2016-04-01

    Cobalt is toxic metal that is present only as a trace in the Earth crust. However, Co might concentrate on specific areas due to both natural and anthropogenic factors and thus, soils and groundwater can be contaminated. It is from this perspective that we are interested in the precipitation of cobalt carbonates, since co-precipitation with minerals phases is a well-known method for metal immobilization in the environment. In particular, the carbonates are widely used due to its reactivity and natural abundance. In order to evaluate the cobalt carbonate precipitation at room temperature, a simple experimental work was carried out in this work. The precipitation occurred via reaction of two common salts: 0.05M of CoCl2 and 0.05M of Na2CO3 in aqueous solution. After reaction, the precipitated solid was kept in the remaining water at 25 oC and under constant stirring for different aging times of 5 min, 1 and 5 hours, 1, 2, 4, 7, 30 and 60 days. In addition to the aging and precipitation experiments, we carried out experiments to determine the solubility of the solids. In these experiments each precipitate was dissolved in Milli-Q water until equilibrium was reached and then the aqueous solution was analyzed regarding Co2+ and total alkalinity. Furthermore, acid solution calorimetry of the products were attained. Finally, we modeled the results using the PHREEQC code. Solid and aqueous phase identification and characterization have been extensively reported in a previous work (González-López et al., 2015). The main results of our investigation were the initial precipitation of an amorphous cobalt carbonate that evolve towards a poorly crystalline cobalt hydroxide carbonate with aging treatment. Solubility of both phases have been calculated under two different approaches: precipitation and dissolution. Values of solubility from each approach were obtained with a general error due to differences in experiment conditions, for instance, ionic strength, temperature and

  1. Reomoval of Heavy Metals from Aqueous Solutions using Bascteria

    Institute of Scientific and Technical Information of China (English)

    HUANGMin-sheng; PANjing; 等

    2001-01-01

    The accumulation of heavy metals by microbial biomass with high surface area-to-volume ratio holds great potential for heavy metal removal in both soluble and particular forms,especially when the heavy metal concentrations are low(<50mg/L),E.coli and B.Subtilis are effective agents for metal removal.We further investigated the effect of pH,temperature,equilibration time,and pre-treatment reagents on the removal of pH(Ⅱ),Cd(Ⅱ) and Cr(VI) from aqueous solutions by E.Coli and B.subtilis.E.coli and B.subtilis were cultivated for 60 hours,the experimentally determined optimal cultivation time before they were used in metal removal experiments,Under the optimal conditions of pH 6.0,equilibration temperature 30℃ and equilibration time 1 hour,63.39% and 69.90%Cd(Ⅱ) can be removed by E.coli and B.subtilis.Under the optimal conditions of pH5.5,equilibration temperature 30℃ and equliobration time 1 hour,68.51% and 67.36% pB(Ⅱ) can be removed by E.coli and B.subtilis.And under the optimal conditons of pH5.5,equilibration temperature 30℃,and equilibration time 1 hour,60.26% and 54.56% Cr(VI) can be removed by E.coli and B.subtilis.Chemical treatment of cultivated bacteria(0.1mol/L NaOH,0.1mol/L HCl,30% ethanol,and distilled water)affects the efficiency of metal removal by E.coli and B.subtilis,pretreatment of biomass by NaOH enhanced Cd(Ⅱ),Pb(Ⅱ)and Cr(VI) removal,while preteatment by HCl,ethanol and distilled water reduced Ca(Ⅱ) ,Pb(Ⅱ) and Cr(VI) removal,For metal removal from industrial waste discharges,pretreated biomass of E.coli can remove 68.5% of Cd and 58.1% of Cr from solutions,while pretreated biomass of B.subtilis can remove 62.6% of Cd and 57% of Cr from Solutions.

  2. Hexavalent uranium diffusion into soils from concentrated acidic and alkaline solutions

    Energy Technology Data Exchange (ETDEWEB)

    Tokunaga, Tetsu K.; Wan, Jiamin; Pena, Jasquelin; Sutton, Stephen R.; Newville, Matthew

    2004-03-29

    Uranium contamination of soils and sediments often originates from acidic or alkaline waste sources, with diffusion being a major transport mechanism. Measurements of U(VI) diffusion from initially pH 2 and pH 11 solutions into a slightly alkaline Altamont soil and a neutral Oak Ridge soil were obtained through monitoring uptake from boundary reservoirs and from U concentration profiles within soil columns. The soils provided pH buffering, resulting in diffusion at nearly constant pH. Micro x-ray absorption near edge structure spectra confirmed that U remained in U(VI) forms in all soils. Time trends of U(VI) depletion from reservoirs, and U(VI) concentration profiles within soil columns yielded K{sub d} values consistent with those determined in batch tests at similar concentrations ({approx} 1 mM), and much lower than values for sorption at much lower concentrations (nM to {mu}M). These results show that U(VI) transport at high concentrations can be relatively fast at non-neutral pH, with negligible surface diffusion, because of weak sorption.

  3. Ion aggregation in high salt solutions. III. Computational vibrational spectroscopy of HDO in aqueous salt solutions

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Jun-Ho; Lim, Sohee; Chon, Bonghwan; Cho, Minhaeng, E-mail: mcho@korea.ac.kr [Center for Molecular Spectroscopy and Dynamics, Institute for Basic Science, Seoul 136-713 (Korea, Republic of); Department of Chemistry, Korea University, Seoul 136-713 (Korea, Republic of); Kim, Heejae; Kim, Seongheun [Department of Chemistry, Korea University, Seoul 136-713 (Korea, Republic of)

    2015-05-28

    The vibrational frequency, frequency fluctuation dynamics, and transition dipole moment of the O—D stretch mode of HDO molecule in aqueous solutions are strongly dependent on its local electrostatic environment and hydrogen-bond network structure. Therefore, the time-resolved vibrational spectroscopy the O—D stretch mode has been particularly used to investigate specific ion effects on water structure. Despite prolonged efforts to understand the interplay of O—D vibrational dynamics with local water hydrogen-bond network and ion aggregate structures in high salt solutions, still there exists a gap between theory and experiment due to a lack of quantitative model for accurately describing O—D stretch frequency in high salt solutions. To fill this gap, we have performed numerical simulations of Raman scattering and IR absorption spectra of the O—D stretch mode of HDO in highly concentrated NaCl and KSCN solutions and compared them with experimental results. Carrying out extensive quantum chemistry calculations on not only water clusters but also ion-water clusters, we first developed a distributed vibrational solvatochromic charge model for the O—D stretch mode in aqueous salt solutions. Furthermore, the non-Condon effect on the vibrational transition dipole moment of the O—D stretch mode was fully taken into consideration with the charge response kernel that is non-local polarizability density. From the fluctuating O—D stretch mode frequencies and transition dipole vectors obtained from the molecular dynamics simulations, the O—D stretch Raman scattering and IR absorption spectra of HDO in salt solutions could be calculated. The polarization effect on the transition dipole vector of the O—D stretch mode is shown to be important and the asymmetric line shapes of the O—D stretch Raman scattering and IR absorption spectra of HDO especially in highly concentrated NaCl and KSCN solutions are in quantitative agreement with experimental results. We

  4. Ion aggregation in high salt solutions. III. Computational vibrational spectroscopy of HDO in aqueous salt solutions.

    Science.gov (United States)

    Choi, Jun-Ho; Kim, Heejae; Kim, Seongheun; Lim, Sohee; Chon, Bonghwan; Cho, Minhaeng

    2015-05-28

    The vibrational frequency, frequency fluctuation dynamics, and transition dipole moment of the O-D stretch mode of HDO molecule in aqueous solutions are strongly dependent on its local electrostatic environment and hydrogen-bond network structure. Therefore, the time-resolved vibrational spectroscopy the O-D stretch mode has been particularly used to investigate specific ion effects on water structure. Despite prolonged efforts to understand the interplay of O-D vibrational dynamics with local water hydrogen-bond network and ion aggregate structures in high salt solutions, still there exists a gap between theory and experiment due to a lack of quantitative model for accurately describing O-D stretch frequency in high salt solutions. To fill this gap, we have performed numerical simulations of Raman scattering and IR absorption spectra of the O-D stretch mode of HDO in highly concentrated NaCl and KSCN solutions and compared them with experimental results. Carrying out extensive quantum chemistry calculations on not only water clusters but also ion-water clusters, we first developed a distributed vibrational solvatochromic charge model for the O-D stretch mode in aqueous salt solutions. Furthermore, the non-Condon effect on the vibrational transition dipole moment of the O-D stretch mode was fully taken into consideration with the charge response kernel that is non-local polarizability density. From the fluctuating O-D stretch mode frequencies and transition dipole vectors obtained from the molecular dynamics simulations, the O-D stretch Raman scattering and IR absorption spectra of HDO in salt solutions could be calculated. The polarization effect on the transition dipole vector of the O-D stretch mode is shown to be important and the asymmetric line shapes of the O-D stretch Raman scattering and IR absorption spectra of HDO especially in highly concentrated NaCl and KSCN solutions are in quantitative agreement with experimental results. We anticipate that this

  5. Gold leaching with elemental sulfur in alkaline solutions under oxygen pressure

    Institute of Scientific and Technical Information of China (English)

    方兆珩; 石伟

    2003-01-01

    A gold leaching process by using oxidation products of elemental sulfur in alkaline solutions was pro-posed and investigated. A gold concentrate and a residue from an arsenic refractory gold concentrate by acidic oxida-tion leaching were tested. The residue contains 16.3% elemental sulfur and no more elemental sulfur was added intests. For the concentrate elemental sulfur was added before leaching tests. The leaching ratio of gold depends main-ly on the initial equivalent ratio of elemental sulfur to hydroxyl ions, the consumption of oxygen and the reactiontemperature in the process. Analysis of the experimental results shows that thiosulfate is the majority complexingreagent for gold in the process. Over 90% gold was leached from the residue and 82%-87% from the concentrate byusing this process.

  6. Kinetics of the decomposition and the estimation of the stability of 10% aqueous and non-aqueous hydrogen peroxide solutions

    Directory of Open Access Journals (Sweden)

    Zun Maria

    2014-12-01

    Full Text Available In this study, the stability of 10% hydrogen peroxide aqueous and non-aqueous solutions with the addition of 6% (w/w of urea was evaluated. The solutions were stored at 20°C, 30°C and 40°C, and the decomposition of hydrogen peroxide proceeded according to first-order kinetics. With the addition of the urea in the solutions, the decomposition rate constant increased and the activation energy decreased. The temperature of storage also affected the decomposition of substance, however, 10% hydrogen peroxide solutions prepared in PEG-300, and stabilized with the addition of 6% (w/w of urea had the best constancy.

  7. Behavior of the sorption of 60 Co in aqueous solution on inorganic materials as function of p H

    International Nuclear Information System (INIS)

    The sorption of the 60 Co is evaluated in aqueous solution on Mg O, MnO2, TiO2, Sn O, activated carbon and hydrotalcite calcined as a function of the p H, using the method for lots and quantifying at the 60 Co for gamma spectrometry. Likewise it was explained the one behavior of the sorption of the 60 Co in the materials with base in the chemical species of this radioactive isotope in aqueous solution. The chemical species of the 60 Co in solution were identified by electrophoresis of high voltage for the different p H values. It was found that under the experimental conditions, the 60 Co showed a significant sorption on MnO2, TiO2 and activated carbon. On the other hand, in Mg O, Sn O and calcined hydrotalcite also was observed a sorption, although in smaller quantities. The studied hydrated metallic oxides retained the 60 Co for ion exchange via. It was found that the 60 Co was present as a cationic specie to p H 1, 3, 5 and 7 and like a neutral specie to alkaline p H. (Author)

  8. Adsorption of Heavy Metal Ions from Aqueous Solutions by Zeolite Based on Oil Shale Ash: Kinetic and Equilibrium Studies

    Institute of Scientific and Technical Information of China (English)

    BAO Wei-wei; ZOU Hai-feng; GAN Shu-cai; XU Xue-chun; JI Gui-juan; ZHENG Ke-yan

    2013-01-01

    Na-A zeolite was successfully synthesized via the alkaline fusion method with oil shale ash as the raw material.The adsorption capacity of it was tested by removing CU2+,Ni2+,Pb2+ and Cd2+ from aqueous solutions.The results reveal the maximum adsorption capacity of adsorbent for Pb2+,Cu2+,Cd2+ and Ni2+ were 224.72,156.74,118.34 and 53.02 mg/g,respectively.The effects of contact time and pH value of solutions on the adsorption efficiency of the zeolite were evaluated.Besides,The equilibrium adsorption data and the batch kinetic data were correlated with Langmuir and Freundlich models and the pseudo-first-order and pseudo-second-order models separately.The results show that the Langmuir isotherm and the pseudo-second-order equation were more suitable for the adsorption of Na-A zeolite for the metal ions.In addition,Thermodynamic parameters of the adsorption(the Gibbs free energy,entropy,and enthalpy) were also evaluated and discussed.The results demonstrate that the adsorption process was spontaneous and endothermic under natural conditions and the synthesized zeolite was an effective adsorbent for the removal of metal ions from aqueous solution.

  9. Preparation of CdTe nanocrystal-polymer composite microspheres in aqueous solution by dispersing method

    Institute of Scientific and Technical Information of China (English)

    LI Minjie; WANG Chunlei; HAN Kun; YANG Bai

    2005-01-01

    Highly fluorescent CdTe nanocrystals were synthesized in aqueous solution, and then processible CdTe nanocrystal-polymer composites were fabricated by coating the aqueous nanocrystals with copolymers of styrene and octadecyl-p-vinyl-benzyldimethylammonium chloride (SOV- DAC) directly. A dichloromethane solution of CdTe nano- crystal-polymer composites was dispersed in the aqueous solution of poly (vinyl alcohol) (PVA) generating highly fluorescent microspheres. Experimental parameters such as the concentration of nanocrystal-polymer composites, the concentration of PVA, and stirring speed which had important effect on the preparation of the microspheres were investigated in detail with fluorescent microscope characterization.

  10. Sensitizing effect of cerium (4) sulfate on photooxidation of organic compounds in aqueous solutions

    International Nuclear Information System (INIS)

    Influence of Ce(SO4)2 addition on the photooxidation rate of organic substances in aqueous solutions has been discussed. It is shown that to a certain value, the rate constant of oxalic acid oxidation increases linearly with increasing oxidant amount. Using a combination of chemical and photochemical oxidation of oxalic acid in aqueous solution with Ce(SO4)2 as a sensitizer, one can increase the oxidation rate by a factor of 45 and to reduce the time required for carbon determination in aqueous solutions from 4-5 hours down to 8-9 min

  11. Hydrate phase equilibria of CO2+N2+aqueous solution of THF, TBAB or TBAF system

    DEFF Research Database (Denmark)

    Sfaxi, Imen Ben Attouche; Durand, Isabelle; Lugo, Rafael;

    2014-01-01

    We report hydrate dissociation conditions of CO2 (15 and 30mol%)+N2 (85 and 70mol%) in the presence of aqueous solutions of THF, TBAB or TBAF. The concentrations of TBAB and TBAF in the aqueous solutions are 5wt% and 9wt% while THF concentration in aqueous solution is 3mol%. Two different...... experimental techniques including isochoric pressure search method and a DSC method are used to measure the hydrate dissociation conditions. A comparison is finally made with the literature data. It is expected that this study provides better understanding of hydrate phase equilibria associated with CO2...

  12. Proton Transfer in Aqueous Solution: Exploring the Boundaries of Adaptive QM/MM

    NARCIS (Netherlands)

    Jiang, Tao; Boereboom, J.M.; Michel, C.; Fleurat-Lessard, P.; Bulo, R.E.

    2015-01-01

    In this chapter, we review the current state-of-the-art in quantum mechanical/molecular mechanical (QM/MM) simulations of reactions in aqueous solutions, and we discuss how proton transfer poses new challenges for its successful application. In the QM/MM description of an aqueous reaction, solvent m

  13. Sulfur species leached from pyrite during oxidative desulfurization of coal in alkaline solutions

    Energy Technology Data Exchange (ETDEWEB)

    Stephenson, M.D.; Wheelock, T.D.; Markuszewski, R.

    1983-01-01

    The results indicate that thiosulfate, sulfite, and sulfate are the principal soluble sulfur species produced when coal-derived pyrite leached with a hot alkaline solution containing dissolved oxygen. The distribution of soluble sulfur species in the leachate was found to depend on leaching temperature, oxygen partial pressure, leachant composition, and time of contact. At lower temperatures and oxygen partial pressures and with a short time of contact between the leaching solution and pyrite, the leachate sulfur species were dominated by thiosulfate. However, the leachate also contained significant amounts of sulfite and sulfate. When the temperature, oxygen partial pressure, or time of contact were increased, the proportions of thiosulfate and sulfite decreased and the proportion of sulfate increased. It was observed also that reacted pyrite particles catalyzed the oxidation of thiosulfate to sulfite and sulfate. Consequently when pyrite was oxidized in a stirred reactor for 1 h at elevated temperature and oxygen partial pressure, most of the dissolved sulfur appeared as sulfate and very little as thiosulfate or sulfite. 10 references, 4 figures, 1 table.

  14. Oxygen reduction at platinum nanoparticles supported on carbon cryogel in alkaline solution

    Directory of Open Access Journals (Sweden)

    N. R. ELEZOVIC

    2007-07-01

    Full Text Available The oxygen reduction reaction was investigated in 0.1 M NaOH solution, on a porous coated electrode formed of Pt particles supported on carbon cryogel. The Pt/C catalyst was characterized by the X-ray diffraction (XRD, transmission electron microscopy (TEM and cyclic voltammetry techniques. The results demonstrated a successful reduction of Pt to metallic form and homogenous Pt particle size distribution with a mean particle size of about 2.7 nm. The ORR kinetics was investigated by linear sweep polarization at a rotating disc electrode. The results showed the existence of two E – log j regions, usually referred to polycrystalline Pt in acid and alkaline solution. At low current densities (lcd, the Tafel slope was found to be close to –2.3RT/F, while at high current densities (hcd it was found to be close to –2×2.3RT/F. It is proposed that the main path in the ORR mechanism on Pt particles was the direct four-electron process, with the transfer of the first electron as the rate determining step. If the activities are expressed through the specific current densities, a small enhancement of the catalytic activity for Pt/C was observed compared to that of polycrystalline Pt. The effect of the Pt particle size on the electrocatalysis of oxygen reduction was ascribed to the predominant (111 facets of the platinum crystallites.

  15. Uranium mobility during interaction of rhyolitic glass with alkaline solutions: dissolution of glass

    Science.gov (United States)

    Zielinski, Robert A.

    1977-01-01

    This report concerns investigations designed to identify the important physical and chemical parameters influencing the rate of release of uranium from glass shards of rhyolitic air-fall ash. Oxidizing, silica undersaturated, alkaline solutions are eluted through a column of rhyolitic glass shards at a carefully controlled temperature, pressure, and flow rate. The solutions are monitored for the concentration of uranium and selected additional elements (Si, K, Li, F), and the glass is recovered and examined for physical and/or chemical evidence of attack. The flushing mode is designed to mimic leaching of glass shards by intermittent, near-surface waters with which the glass is not in equilibrium. Reported rates are applicable only to the experimental conditions (120?C, 7,000 psi), but it is assumed that the reaction mechanisms and the relative importance of rate-influencing parameters remain unchanged, at reduced temperature and pressure. Results of the above experiment indicate that silica and uranium are released from glass shards at comparable rates, while lithium and potassium are released faster and fluorine slower than either Si or U. Rates of release of silica and uranium correlate positively with the surface area of the shards. Rhyolitic shards release uranium at faster rates than rhyodacitic shards of comparable surface area. Changes in the shards resulting from experimental treatment and observed in the original glass separates from an Oligocene ash (compared to a Pleistocene ash) include; surface pitting, increased surface area, devitrification rinds (rate on the relative mobility of U, Si, Li, F, and K.

  16. Stability of ZnMgO oxide in a weak alkaline solution

    Energy Technology Data Exchange (ETDEWEB)

    Diler, E. [Laboratoire de Magnetisme de Bretagne, EA 4522, CNRS, Universite de Brest, UBO, 6 av. Le Gorgeu, 29285 Brest Cedex (France); Institut de la Corrosion, 220 rue Pierre Rivoalon, 29200 Brest (France); Rioual, S., E-mail: rioual@univ-brest.fr [Laboratoire de Magnetisme de Bretagne, EA 4522, CNRS, Universite de Brest, UBO, 6 av. Le Gorgeu, 29285 Brest Cedex (France); Lescop, B. [Laboratoire de Magnetisme de Bretagne, EA 4522, CNRS, Universite de Brest, UBO, 6 av. Le Gorgeu, 29285 Brest Cedex (France); Thierry, D. [Institut de la Corrosion, 220 rue Pierre Rivoalon, 29200 Brest (France); Rouvellou, B. [Laboratoire de Magnetisme de Bretagne, EA 4522, CNRS, Universite de Brest, UBO, 6 av. Le Gorgeu, 29285 Brest Cedex (France)

    2012-01-31

    Zinc oxide (ZnO) is a chemical compound of great interest used, for example, as photocatalyst in the purification of wastewater or polluted air. However, neither dissolution, nor photo-dissolution of ZnO is negligible: indeed, both processes reduce significantly the efficiency of photocatalysis and then lead to a secondary pollution by free Zn{sup 2+}. In the present study, the stability of ZnMgO thin films in weak alkaline solution is investigated. We demonstrate that the replacement of Zn{sup 2+} ion with Mg{sup 2+} ion results in the production of a Zn{sub 0.84}Mg{sub 0.16}O solid solution, whose stability is higher than that of the ZnO sample. This alloy, thus, constitutes an alternative to the use of ZnO in photocatalysis applications. To gain more insights into the higher resistance of such alloys to the dissolution process, X-Ray photoelectron spectroscopy measurements were performed. They highlighted the role of OH group adsorption in the experimentally observed enhancement of ZnMgO stability.

  17. Absorption of nitric oxide into aqueous solutions of ferrous chelates accompanied by instantaneous reaction

    NARCIS (Netherlands)

    Demmink, J.F; vanGils, I.C.F.; Beenackers, A.A C M

    1997-01-01

    The absorption of nitric oxide (NO) into aqueous solutions of ferrous chelates of nitrilotriacetic acid (NTA), ethylene diaminetetraacetic acid (EDTA), hydroxyethylenediaminetriacetic acid (HEDTA), and diethylenetriaminepentaacetic acid (DTPA) was studied in a stirred cell reactor. Experimental cond

  18. Formation of anhydrotetracycline in gamma irradiated aqueous tetracycline solutions (Preprint No. RC-12)

    International Nuclear Information System (INIS)

    Gamma radiolysis of antibiotic tetracycline in aqueous solutions has been studied under various conditions. Anhydrotetracycline, a potential toxic substance, was identified as a major radiation degradation product formed under deoxygenated conditions mainly because of H atom attack on tetracycline. (author)

  19. Thermodynamics of the complexation of arabinogalactan with salicylic and p-aminobenzoic acids in aqueous solutions

    Science.gov (United States)

    Mudarisova, R. Kh.; Badykova, L. A.

    2016-03-01

    The thermodynamics of complexation of arabinogalactan with salicylic and p-aminobenzoic acids in aqueous solutions is studied by means spectroscopy. The standard thermodynamic characteristics (Δ H°; Δ G°; Δ S°) of complexation are calculated.

  20. Separation of radiostrontium from alkaline reprocessing waste solution using a fixed-bed column of chelating iminodiacetic acid resin

    International Nuclear Information System (INIS)

    A fixed-bed ion exchange column filled with a chelating resin containing iminodiacetic acid functional groups has been tested for removal of strontium from simulated alkaline reprocessing waste solution. The breakthrough curve has been established. Column loading performance is correlated with batch equilibration results. The loaded strontium is eluted in a small volume of 0.5 M HNO3. (author)

  1. Supercooling of aqueous dimethylsulfoxide solution at normal and high pressures: Evidence for the coexistence of phase-separated aqueous dimethylsulfoxide solutions of different water structures

    Science.gov (United States)

    Kanno, H.; Kajiwara, K.; Miyata, K.

    2010-05-01

    Supercooling behavior of aqueous dimethylsulfoxide (DMSO) solution was investigated as a function of DMSO concentration and at high pressures. A linear relationship was observed for TH (homogeneous ice nucleation temperature) and Tm (melting temperature) for the supercooling of aqueous DMSO solution at normal pressure. Analysis of the DTA (differential thermal analysis) traces for homogeneous ice crystallization in the bottom region of the TH curve for a DMSO solution of R =20 (R: moles of water/moles of DMSO) at high pressures supported the contention that the second critical point (SCP) of liquid water should exist at Pc2=˜200 MPa and at Tc2<-100 °C (Pc2: pressure of SCP, Tc2: temperature of SCP). The presence of two TH peaks for DMSO solutions (R =15, 12, and 10) suggests that phase separation occurs in aqueous DMSO solution (R ≤15) at high pressures and low temperatures (<-90 °C). The pressure dependence of the two TH curves for DMSO solutions of R =10 and 12 indicates that the two phase-separated components in the DMSO solution of R =10 have different liquid water structures [LDL-like and HDL-like structures (LDL: low-density liquid water, HDL: high-density liquid water)] in the pressure range of 120-230 MPa.

  2. Reactant-solute encounters in aqueous solutions studied by kinetic methods : hydration cosphere overlap and camouflage effects

    NARCIS (Netherlands)

    Engberts, Jan B.F.N.; Blandamer, Michael J.

    1998-01-01

    Rates of chemical reactions in aqueous solutions are often sensitive to low concentrations of added solutes such as ureas, alcohols, α-amino acids and carbohydrates. In this work, several simple chemical reactions were used to probe this sensitivity, which arises from interactions between added solu

  3. Relation between the solubility of proteins in aqueous solutions and the second virial coefficient of the solution

    NARCIS (Netherlands)

    Haas, C; Drenth, J; Wilson, WW

    1999-01-01

    Tn recent publications it was pointed out that there is a correlation between the observed values of the solubility of proteins in aqueous solutions and the second virial coefficient of the solution. In this paper we give a theoretical explanation of this relation. The derived theoretical expression

  4. Biosorption of Lead Ions from Aqueous Solution Using Ficus benghalensis L.

    OpenAIRE

    Venkateswara Rao Surisetty; Janusz Kozinski; L. Rao Nageswara

    2013-01-01

    Ficus benghalensis L., a plant-based material leaf powder, is used as an adsorbent for the removal of lead ions from aqueous solution using the biosorption technique. The effects of process parameters such as contact time, adsorbent size and dosage, initial lead ion concentration, and pH of the aqueous solution on bio-sorption of lead by Ficus benghalensis L. were studied using batch process. The Langmuir isotherm was more suitable for biosorption followed by Freundlich and Temkin isotherms w...

  5. Separation of Co2+ present in aqueous solution on calcium carbonate

    International Nuclear Information System (INIS)

    The CaCO3 was synthesized by precipitation method and characterized using SEM, EDS, TGA and IR. It was studied the adsorption behavior of Co2+ present in aqueous solution on the synthesized material by experiments batch type at room temperature. Was found that removal of cobalt ions was greater than 40% indicating that this material can be used to remove Co2+ present in aqueous solution. (Author)

  6. Synthesis and aggregation properties of amphiphilic mono and bisadducts of fullerene in aqueous solution

    Institute of Scientific and Technical Information of China (English)

    Pu Zhang; Zhi Xin Guo; Shuang Lv

    2008-01-01

    New amphiphilic[60]fullerene monoadduet TPF and bisadducts BTPF were synthesized and well-characterized. Their aggregation properties in aqueous solution was investigated by UV-vis and TEM methods. In aqueous solution, monoadduct TPF forms irregularly shaped and some rod-like aggregates, whereas bisadducts BTPF gives spherical aggregates with diameters of 50-150 nm. It indicated that the aggregation properties of amphiphilic fullerene derivatives depend on the number of hydrophilic appendage on the C60 cage.

  7. Radiation-induced destruction peculiarities of hydroxyl containing amino acids in diluted aqueous solution

    International Nuclear Information System (INIS)

    Amino acids aqueous solution of alpha-alanine and beta-alanine, serine, threonine (concentration 5*10-4 M) were irradiated with dose rate 0.35 Gy/s in range 100-1100 Gy and analysed. Effectiveness of radiation-induced decomposition process depends on row of factors: concentration of amino acid aqueous solution, pH, oxygen presence and other acceptors

  8. Pervaporation of Aqueous Solution of Acetaldehyde Through ZSM-5 Filled PDMS Composite Membrane

    Institute of Scientific and Technical Information of China (English)

    伍艳辉; 谭惠芬; 李佟茗; 金源

    2012-01-01

    Hydrophobic ZSM-5 zeolite filled polydimethylsiloxane (PDMS) composite membranes with Nylon micro-filtration membrane as the support layer were prepared to separate acetaldehyde from its aqueous solution. The composite membranes were characterized by Fourier transform infrared spectroscopy and X-ray diffraction. Their structural morphology and thermal stability were also examined. The swelling study showed that the composite membranes presented higher degree of swelling in aqueous solution of acetaldehyde than in pure water at 25℃,

  9. Determination of deuterium in brines and in hypersaline aqueous solutions by mass spectrometry using zinc as reducing agent

    International Nuclear Information System (INIS)

    A procedure was developed for the determination of deuterium concentration in brines and in hypersaline aqueous solutions, without the removal of alkaline earth metal cations. Aqueous salt solutions of nine salts, LiCl, NaCl, NaI, Na2CO3, KCl, K2SO4, CsCl, CaCl2 and Mg(ClO4)2, with molalities ranging from 0.5 to 11.8 mol kg-1 were prepared by dissolving the dry anhydrous salts in de-ionized water of known isotopic composition. Only 8 μl of sample were required to be reduced with zinc metal at 460oC in a special glass container equipped with a Teflon stopper, to prepare hydrogen for isotopic analysis. The salts NaCl, NaI, Na2CO3, KCl, K2SO4 and CsCl required 0.25 g, LiCl and CaCl2 0.75 g and Mg(ClO4)2 1.00 g of zinc for complete reduction. Deuterium concentrations in brines containing large amounts of Ca2+, Mg2+, Cl- and SO42- ions were measured with an accuracy of ±1%o (1σ). In addition, the deuterium content in Dead Sea water was determined with the same method and gave δD = + 5.4 ±0.3%o using 1.50 g of zinc. (author)

  10. Equilibrium, kinetic and thermodynamic studies for sorption of Ni (II from aqueous solution using formaldehyde treated waste tea leaves

    Directory of Open Access Journals (Sweden)

    Jasmin Shah

    2015-05-01

    Full Text Available The sorption characteristic of Ni (II from aqueous solution using formaldehyde treated waste tea leaves as a low cost sorbent has been studied. The effect of pH, contact time, sorbent dose, initial metal ion concentration and temperature were investigated in batch experiments. The equilibrium data were fitted into four most common isotherm models; Freundlich, Langmuir, Tempkin and Dubinin–Radushkevich (D–R. The Langmuir model described the sorption isotherm best with maximum monolayer sorption capacity of 120.50 mg g−1. Four kinetic models, pseudo-first-order, pseudo-second-order, intraparticle diffusion and Elovich were employed to explain the sorption mechanism. The kinetics of sorption data showed that the pseudo-second-order model is the best with correlation coefficient of 0.9946. The spontaneous and exothermic nature of the sorption process was revealed from thermodynamic investigations. The effect of some common alkali and alkaline earth metal ions were also studied which showed that the presence of these ions have no effect on the sorption of Ni (II. The results showed that waste tea leaves have the potential to be used as a low cost sorbent for the removal of Ni (II from aqueous solutions.

  11. Magnetic composite nanofibers fabricated by electrospinning of Fe{sub 3}O{sub 4}/gelatin aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Shuhong, E-mail: openair@163.com [Key Laboratory of Functional Inorganic Material Chemistry (School of Chemical Engineering and Material, Heilongjiang University), Ministry of Education, Harbin 150080 (China); Sun, Zhiyao [Key Laboratory of Functional Inorganic Material Chemistry (School of Chemical Engineering and Material, Heilongjiang University), Ministry of Education, Harbin 150080 (China); Yan, Eryun [College of Materials Science and Engineering, Qiqihar University, Qiqihar 161006 (China); Yuan, Jihong; Gao, Yang; Bai, Yuhao; Chen, Yu [Key Laboratory of Functional Inorganic Material Chemistry (School of Chemical Engineering and Material, Heilongjiang University), Ministry of Education, Harbin 150080 (China); Wang, Cheng, E-mail: wangc_93@163.com [Key Laboratory of Functional Inorganic Material Chemistry (School of Chemical Engineering and Material, Heilongjiang University), Ministry of Education, Harbin 150080 (China); Zheng, Yongjie; Jing, Tao [College of Materials Science and Engineering, Qiqihar University, Qiqihar 161006 (China)

    2014-12-15

    Graphical abstract: Superparamagnetic Fe{sub 3}O{sub 4}/GE composite nanofibers with saturation magnetization of 12.87 emμ g{sup −1} were prepared from gelatin aqueous solution at an elevated temperature by electrospinning. - Highlights: • Electrospinning GE aqueous solution at higher temperature. • Presenting a simple and effective technique, combining wet blending with high temperature electrospinning to prepare magnetic composite nanofibers. • Developing composite nanofibers with higher superparamagnetic properties is expected to be useful in application for the biomedical field. - Abstract: We have fabricated magnetic composite nanofibers containing superparamagnetic Fe{sub 3}O{sub 4} nanoparticles by the electrospinning method. Highly dispersed Fe{sub 3}O{sub 4} magnetic nanoparticles were synthesized by one-step co-precipitation of Fe{sup 2+}/Fe{sup 3+} under an alkaline condition with 4 wt% poly(vinyl alcohol) (PVA) aqueous solution as the stabilizer. Gelatin (GE) was used as a polymeric matrix for fabricating the nanocomposites. The prepared Fe{sub 3}O{sub 4}/GE composite nanofibers were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD), respectively. These composite nanofibers show uniform and continuous morphology with the Fe{sub 3}O{sub 4} nanoparticles embedded in the nanofibers. By studying the magnetic properties of the Fe{sub 3}O{sub 4}/GE composite nanofibers, we confirm that the composite nanofibers possess superparamagnetic properties with a high saturated magnetization (M{sub s} = 12.87 emμ g{sup −1}) at room temperature. The features of this approach for getting one-dimensional magnetic nanostructure are its simplicity, effectiveness and safety. The Fe{sub 3}O{sub 4}/GE nanofibers with superparamagnetic properties would be potentially applied in biomedical field.

  12. Kinetics of ozone-phenol reaction in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Joshi, M.G.; Shambaugh, R.L.

    1982-01-01

    The kinetics of the reaction of ozone and phenol in aqueous medium was studied. The reaction was first order with respect to both ozone and phenol. The rate constant was found to increase with increase in the pH of the reaction mixture. Four different catalysts were examined for their effect on the rate of reaction. 30 refs.

  13. Characterization of trehalose aqueous solutions by neutron spin echo

    CERN Document Server

    Branca, C; Magazù, S; Maisano, G; Mangione, A; Pappas, C; Triolo, A

    2002-01-01

    The present work reports neutron spin-echo (NSE) results on aqueous mixtures of trehalose, a naturally occurring disaccharide of glucose, which shows an extraordinary bioprotective effectiveness against dehydration and freezing. The aim of the work is to furnish new results on the dynamics of the trehalose/water system on the nano- and picosecond scales. (orig.)

  14. Interaction between bacteriophage and pyrophyllite clay in aqueous solution

    Science.gov (United States)

    Park, Jeong-Ann; Kim, Jae-Hyun; Kang, Jin-Kyu; Son, Jeong-Woo; Yi, In-Geol; Kim, Song-Bae

    2014-05-01

    Viral contamination results in a degradation in drinking water quality and a threat to public health. Toprovide safe drinking water, water treatment alternatives using various adsorbents and filter media such as activated carbon, bituminous coal, quartz sand and clay have been considered. Pyrophyllite is a 2:1 clay mineral having dioctahedral layer structure with octahedrally coordinated Al ion sheets between two sheets of SiO4 tetrahedra. It is a hydrous aluminosilicate clay with the chemical composition AlSi2O5(OH). Pyrophyllite has recently been investigated as a potential low-cost and environmental friendly adsorbent for removing various contaminants. The aim of this study was to investigate the removal of the bacteriophage MS2 from aqueous solution using pyrophyllite. Batch experiments were conducted to examine the MS2 sorption to pyrophyllite. The influence of fluoride, a groundwater contaminant, on the removal of MS2 was also observed. Batch results demonstrated that pyrophyllite was effective in MS2 removal. The percent removal increased from 5.26% to 99.99% (= 4.0 log removal) as the pyrophyllite concentrations increased from 0.2 to 20 g/L. More than 99% of MS2 could be removed with a pyrophyllite concentration of ≥ 4 g/L. The sorption of MS2 to pyrophyllite was rapid. Within 15 min, approximately 99.98% (= 3.7 log removal) of MS2 was attained. More than 4.0 log removal was achieved after 180 min. The experimental data were analyzed with the pseudo first-order and pseudo second-order kinetic models. The correlation coefficient showed that pseudo second-order model was better than pseudo first-order model at describing the kinetic data. The amount of MS2 removed at equilibrium was determined to be 1.43 × 108 pfu/g from the pseudo second-order model. The experimental data were also analyzed with the Freundlich and Langmuir isotherm models. The correlation coefficients showed that the Langmuir model was more suitable than the Freundlich model for MS2

  15. Reusable nanocomposite of CoFe2O4/chitosan-graft-poly(acrylic acid) for removal of Ni(II) from aqueous solution

    International Nuclear Information System (INIS)

    In this paper, CoFe2O4/chitosan-graft-poly(acrylic acid) (CoFe2O4/CS-graft-PAA) nanocomposites were prepared successfully by coprecipitation of the compounds in alkaline solution and were used for removal of nickel (II) ions from aqueous solution. The sorption rate was affected significantly by the initial concentration of the solution, sorbent amount, and pH value of the solution. Batch experiments were conducted to investigate the adsorption capacity under different initial concentration (ranging from 25 to 150 mg L−1), solution pH (4.1, 5.3, 6.4 and 7.6), and contact time. These nanocomposites can be recycled conveniently from water with the assistance of an external magnet because of their exceptional properties. The prepared nanocomposites were characterized by Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), x-ray powder diffraction (XRD), and thermogravimetric analysis (TGA). (papers)

  16. Aqueous solutions of acidic ionic liquids for enhanced stability of polyoxometalate-carbon supercapacitor electrodes

    Science.gov (United States)

    Hu, Chenchen; Zhao, Enbo; Nitta, Naoki; Magasinski, Alexandre; Berdichevsky, Gene; Yushin, Gleb

    2016-09-01

    Nanocomposites based on polyoxometalates (POMs) nanoconfined in microporous carbons have been synthesized and used as electrodes for supercapacitors. The addition of the pseudocapacitance from highly reversible redox reaction of POMs to the electric double-layer capacitance of carbon lead to an increase in specific capacitance of ∼90% at 1 mV s-1. However, high solubility of POM in traditional aqueous electrolytes leads to rapid capacity fading. Here we demonstrate that the use of aqueous solutions of protic ionic liquids (P-IL) as electrolyte instead of aqueous sulfuric acid solutions offers an opportunity to significantly improve POM cycling stability. Virtually no degradation in capacitance was observed in POM-based positive electrode after 10,000 cycles in an asymmetric capacitor with P-IL aqueous electrolyte. As such, POM-based carbon composites may now present a viable solution for enhancing energy density of electrical double layer capacitors (EDLC) based on pure carbon electrodes.

  17. The kinetics of dye formation by pulse radiolysis of pararosaniline cyanide in aqueous or organic solution

    International Nuclear Information System (INIS)

    The radiation-induced conversion of the leucocyanide of pararosaniline dye to the highly colored salt-isomer of the dye in acidic aqueous solution (wavelength of maximum absorption lambda sub(max)=540 nm) or polar organic solution (lambda sub(max)=550 nm), takes place in two separate processes. The first is very fast (within 3 s-1 to 106 s-1, as the acidity or concentration of an oxidizing agent increases. In oxygen-free acidic aqueous or organic solutions (argon saturated) there is an unstable transient species (lambdasub(max)=380 nm). When using O2 or N2O-saturated aqueous or organic solution, there is no intermediate absorption band at 380 nm, but the slow process of dye formation at 540 or 550 nm is still sequential to the initial fast process having somewhat faster kinetics than in Ar-saturated solution. (author)

  18. Photo-Fenton oxidation of phenol and organochlorides (2,4-DCP and 2,4-D) in aqueous alkaline medium with high chloride concentration.

    Science.gov (United States)

    Luna, Airton J; Chiavone-Filho, Osvaldo; Machulek, Amilcar; de Moraes, José Ermírio F; Nascimento, Cláudio A O

    2012-11-30

    A highly concentrated aqueous saline-containing solution of phenol, 2,4-dichlorophenoxyacetic acid (2,4-D) and 2,4-dichlorophenol (2,4-DCP) was treated by the photo-Fenton process in a system composed of an annular reactor with a quartz immersion well and a medium-pressure mercury lamp (450 W). The study was conducted under special conditions to minimize the costs of acidification and neutralization, which are usual steps in this type of process. Photochemical reactions were carried out to investigate the influence of some process variables such as the initial concentration of Fe(2+) ([Fe(2+)](0)) from 1.0 up to 2.5 mM, the rate in mmol of H(2)O(2) fed into the system (FH(2)O(2);in) from 3.67 up to 7.33 mmol of H(2)O(2)/min during 120 min of reaction time, and the initial pH (pH(0)) from 3.0 up to 9.0 in the presence and absence of NaCl (60.0 g/L). Although the optimum pH for the photo-Fenton process is about 3.0, this particular system performed well in experimental conditions starting at alkaline and neutral pH. The results obtained here are promising for industrial applications, particularly in view of the high concentration of chloride, a known hydroxyl radical scavenger and the main oxidant present in photo-Fenton processes. PMID:22809483

  19. Photo-Fenton oxidation of phenol and organochlorides (2,4-DCP and 2,4-D) in aqueous alkaline medium with high chloride concentration.

    Science.gov (United States)

    Luna, Airton J; Chiavone-Filho, Osvaldo; Machulek, Amilcar; de Moraes, José Ermírio F; Nascimento, Cláudio A O

    2012-11-30

    A highly concentrated aqueous saline-containing solution of phenol, 2,4-dichlorophenoxyacetic acid (2,4-D) and 2,4-dichlorophenol (2,4-DCP) was treated by the photo-Fenton process in a system composed of an annular reactor with a quartz immersion well and a medium-pressure mercury lamp (450 W). The study was conducted under special conditions to minimize the costs of acidification and neutralization, which are usual steps in this type of process. Photochemical reactions were carried out to investigate the influence of some process variables such as the initial concentration of Fe(2+) ([Fe(2+)](0)) from 1.0 up to 2.5 mM, the rate in mmol of H(2)O(2) fed into the system (FH(2)O(2);in) from 3.67 up to 7.33 mmol of H(2)O(2)/min during 120 min of reaction time, and the initial pH (pH(0)) from 3.0 up to 9.0 in the presence and absence of NaCl (60.0 g/L). Although the optimum pH for the photo-Fenton process is about 3.0, this particular system performed well in experimental conditions starting at alkaline and neutral pH. The results obtained here are promising for industrial applications, particularly in view of the high concentration of chloride, a known hydroxyl radical scavenger and the main oxidant present in photo-Fenton processes.

  20. Production of ultrafine zinc powder from wastes containing zinc by electrowinning in alkaline solution

    Directory of Open Access Journals (Sweden)

    Zhao Youcai

    2013-12-01

    Full Text Available Production of ultrafine zinc powder from industrial wastes by electrowinning in alkaline solution was studied. Stainless steel and magnesium electrodes were used as anode and cathode, respectively. Morphology, size distribution and composition of the Zn particles were characterized by Scanning Electron Microscopy, Laser Particle Size Analyzer, and Inductive Coupled Plasma Emission Spectrometer. The required composition of the electrolyte for ultrafine particles was found to be 25-35 g/L Zn, 200-220 g/L NaOH and 20-40 mg/L Pb. The optimal conditions were a current density of 1000-1200 A/m² and an electrolyte temperature of 30-40 °C. The results indicated that the lead additive exerted a beneficial effect on the refining of the particles, by increasing the cathodic polarization. Through this study, ultrafine zinc powder with a size distribution of around 10 μm could be produced, and considerably high current efficiencies (97-99 % were obtained.

  1. Ultraviolet spectrum and decay of the ozonide ion radical, O3-, in strong alkaline solution

    International Nuclear Information System (INIS)

    Pulse radiolytic experiments in strong alkaline solution (pH 13-14) on the formation and the decay of the ozonide ion radical, O3-, are reported. The high-pressure cell technique was used applying 4 MPa of nitrous oxide and 0.1 MPa of oxygen. The spectrum of O3- in the uv was measured and the decay product was identified as the peroxy radical ion, O2-. A complete mechanism for the decay of O3- is based on the following reactions: O3- + O- → 2O2- and O2- + O- + H2O → O2 + 2OH-. A computer simulation of the high-pressure system as well as the atmospheric-pressure oxygenated system supports this mechanism and yields a rate constant, k/sub (O3- + O-)/ of (7.0 +- 1.0) x 108 dm3 mol-1s-1. As a consequence of our mechanism, a k/sub (O2- + O-)/ of (6.0 +- 1.0) x 108 dm3 mol-1 s-1 is also derived from the computations

  2. Apatite formation on alkaline-treated dense TiO2 coatings deposited using the solution precursor plasma spray process.

    Science.gov (United States)

    Chen, Dianying; Jordan, Eric H; Gell, Maurice; Wei, Mei

    2008-05-01

    A dense titania (TiO2) coating was deposited from an ethanol-based solution containing titanium isopropoxide using the solution precursor plasma spray (SPPS) process. XRD and Raman spectrum analyses confirmed that the coating is exclusively composed of rutile TiO2. SEM micrographs show the as-sprayed coating is dense with a uniform thickness and there are no coarse splat boundaries. The as-sprayed coating was chemically treated in 5M NaOH solution at 80 degrees C for 48 h. The bioactivity of as-sprayed and alkaline-treated coatings was investigated by immersing the coatings in simulated body fluid (SBF) for 14-28 days, respectively. After 28 days immersion, there is a complete layer of carbonate-containing apatite formed on the alkaline-treated TiO2 coating surface, but none formed on the as-sprayed coating.

  3. Catalytic condensation of formaldehyde in aqueous solution initiated by UV irradiation as putative "prebiological" route of the monosaccharides formation

    Science.gov (United States)

    Pestunova, O. P.; Simonov, A. N.; Matvienko, L. G.; Snytnikov, V. N.; Parmon, V. N.; Snytnikova, O. A.; Tsentalovich, Yu. P.

    The condensation of formaldehyde into higher monosaccharides in aqueous alkaline solutions catalyzed by several metal ions in particular Ca 2 and Mg 2 named as formose reaction is considered as a probable source of carbohydrates in prebiotic conditions Formaldehyde is detected in significant amounts in molecular clouds in space Undoubtedly it was an important gas component of circumsolar protoplanet disk Naturally formaldehyde could be dissolved in water of the Protoearth Calcium and magnesium that are capable of creating an alkaline medium are the abundant elements Thus the basic conditions for the formose reaction and for formation of monosaccharides in nature could be met However the formose reaction is autocatalytic since it can be initiated only in the presence of carbohydrates In spite of the fact that Russian chemist Butlerov discovered the formose reaction almost 150 years ago the reason of autocatalytic character of the process and the mechanism of initiation till now remained not quite clear In our work regular investigation of the mechanism of the formose reaction was carried out Influence of various initiators on reaction kinetics and composition of products was studied The composition of the formose reaction products in presence of different initiators is practically invariable under steady-state conditions and is caused by an aldol condensation of the lowest N 2 - and C 3 -carbohydrates The ability of the C 4 -C 6 sugars to initiate the formose reaction is revealed to correlate with the

  4. Effect of alkaline solutions on the tensile properties of glass-polyester pipes

    Directory of Open Access Journals (Sweden)

    Putić Slaviša S.

    2011-01-01

    Full Text Available Construction materials, traditionally used in process equipment, are today successfully replaced by composite materials. Hence, many pipes are made of these materials. The subject of this study was the influence of liquids on the state of stresses and tensile strengths in the longitudinal and circumferential direction of glass-polyester pipes of a definite structure and known fabrication process. These analyses are of great importance for the use of glass-polyester pipes in the chemical industry. The tensile properties (the ultimate tensile strength and the modulus of elasticity were tested and determined for specimens cut out of the pipes; flat specimens for the tensile properties in the longitudinal direction and ring specimens for the tensile properties in the circumferential direction. First, the tension test was performed on virgin samples (without the influence of any liquid, to obtain knowledge about the original tensile properties of the material composite studied. Subsequently, the specimens were soaked in alkaline solutions: sodium hydroxide (strong alkali and ammonium hydroxide (weak alkali. These solutions were selected because of their considerable difference in pH values. The specimens and rings were left for 3, 10, 30 and 60 days in each liquid at room temperature. Then, the samples were tested on tension by the standard testing procedure. A comparison of the obtained results was made based on the pH values of the aggressive media in which the examined material had been soaked, as well as based on the original tensile properties and the number of days of treatment. Micromechanical analyses of sample breakage helped in the elucidation of the influence of the liquids on the structure of the composite pipe and enabled models and mechanisms that produced the change of strength to be proposed.

  5. Influence of starch origin on rheological properties of concentrated aqueous solutions

    OpenAIRE

    Stojanović Željko P.; Jeremić Katarina B.; Jovanović Slobodan M.

    2011-01-01

    The rheological properties of corn and potato starch concentrated aqueous solutions were investigated at 25ºC. The starches were previously dispersed in water and the solutions were obtained by heating of dispersions at 115-120ºC for 20 minutes. The solutions of potato starch were transparent, while the corn starch solutions were opalescent. The results of dynamic mechanical measurements showed that the values of viscosity, h, storage modulus, G′, and loss modulus, G″, of the corn starc...

  6. Tetraethyl Orthosilicate Coated Hydroxyapatite Powders for Lead Ions Removal from Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Rodica V. Ghita

    2014-01-01

    Full Text Available The goal of this study was to synthetize and characterize a porous material based on tetraethyl orthosilicate (TEOS coated hydroxyapatite (HApTh after removal experiments of Pb2+ ions from aqueous solutions. In order to study the morphology and composition, the samples obtained after removal experiments of Pb2+ ions from aqueous solution with the initial Pb2+ ion concentrations of the aqueous solutions were 0.1 g·L−1 (HApTh-50 and 0.9 g·L−1 (HApTh-450 have been investigated by scanning electron microscopy (SEM equipped with an energy dispersive X-ray spectrometer (EDS, Fourier transform infrared spectroscopy (FTIR, and transmission electron microscopy (TEM. Removal experiments of Pb2+ ions were carried out in aqueous solutions with controlled concentration of Pb2+. After the removal experiment of Pb2+ ions from solutions, porous hydroxyapatite nanoparticles were transformed into HApTh-50 and HApTh-450 due to the adsorption of Pb2+ ions followed by a cation exchange reaction. The obtained results show that the porous HApTh nanopowders could be used for Pb2+ ions removal from aqueous solutions.

  7. Experimental determination of the temperature dependence of water activities for a selection of aqueous organic solutions

    Directory of Open Access Journals (Sweden)

    G. Ganbavale

    2014-05-01

    Full Text Available This work presents experimental data of the temperature dependence of water activity in aqueous organic solutions relevant for tropospheric conditions (200–273 K. Water activity (aw at low temperatures (T is a crucial parameter for predicting homogeneous ice nucleation. We investigated temperature dependent water activities, ice freezing and melting temperatures of solutions, and vapour pressures of a selection of atmospherically relevant aqueous organic systems. To measure aw over a wide composition range and with a focus on low temperatures, we use various aw measurement techniques and instruments: a dew point water activity meter, an electrodynamic balance (EDB, differential scanning calorimetry (DSC, and a setup to measure the total gas phase pressure at equilibrium over aqueous solutions. Water activity measurements were performed for aqueous multicomponent and multifunctional organic mixtures containing the functional groups typically found in atmospheric organic aerosols, such as hydroxyl, carboxyl, ketone, ether, ester, and aromatic groups. The aqueous organic systems studied at several fixed compositions over a considerable temperature range differ significantly in their temperature dependence. Aqueous organic systems of 1,4-butanediol and methoxyacetic acid show a moderate decrease in aw with decreasing temperature. The aqueous M5 system (a multicomponent system containing five different dicarboxylic acids and aqueous 2-(2-ethoxyethoxyethanol solutions both show a strong increase of water activity with decreasing temperature at high solute concentrations for TTaw can be reversed at low temperatures and that linear extrapolations of high temperature data may lead to erroneous predictions. To avoid this, experimentally determined aw at low temperature are needed to improve thermodynamic models towards lower temperatures and for improved predictions of the ice nucleation ability of organic–water systems.

  8. Sorption Potentials of Waste Tyre for Some Heavy Metals (Pb Cd in Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Austin Kanayo ASIAGWU

    2009-07-01

    Full Text Available An investigation into the adsorption potential of activated and inactivated waste tyre powders for some heavy metals (Pb2+ and Cd2+ in their aqueous solution has been studied. The result indicated that inactivated waste tyre is a good non-conventional adsorbent for the removal of Cd from aqueous solution. A total of 93.3% of Cadmium contents was removed. The inactivated waste type proved a good adsorbent for the removal of Pb2+ 5g of 500mm activated tyre removed over 86.66% of Pb2+ from solution.

  9. Investigation of Durasil absorbers for the removal of radionuclides from aqueous solutions

    International Nuclear Information System (INIS)

    Inorganic ion-exchange materials supplied by the Duratek Corporation, Maryland, USA have been tested in batch contact experiments to assess their effectiveness in removing radionuclides from aqueous solutions. The three absorbers tested, D10, D70 and D190, showed an affinity for all fourteen radionuclides present in the test solutions. (author)

  10. Study on Thermosensitive Micellization of Dextran-g-PNIPAAm in Aqueous Solutions

    Institute of Scientific and Technical Information of China (English)

    Dan ZHAO; Li Qun WANG; Ke Hua TU; Song Wei TAN

    2006-01-01

    The thermosensitive micellization of dextran-g-PNIPAAm in aqueous solutions has been investigated by fluorescence spectroscopy, dynamic light scattering and transmission electron microscope. The formed polymeric micelles showed different diameters of about 20 nm or 100nm, when the solution temperature was below or above the phase transition temperature.

  11. Temporarily plugging a subterranean reservoir with a self-foaming aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Berkshire, D.C.; Lybarger, J.H.; Reisberg, J.; Richardson, E.A.; Scheuerman, R.F.

    1980-11-11

    Portions of a subterranean reservoir are temporarily plugged by injecting an aqueous liquid solution which contains nitrogen gasgenerating reactants, a foaming surfactant and a pH controlling system arranged so that the solution remains relatively unreactive within the well but forms a relatively immobile foam within the pores or other openings within the reservoir formation.

  12. Aqueous solutions of proline and NaCl studied by differential scanning calorimetry at subzero temperatures

    DEFF Research Database (Denmark)

    Rasmussen, Peter Have; Jørgensen, Bo; Nielsen, Jette

    1997-01-01

    The hydration properties of proline are studied by differential scanning calorimetry (DSC) in aqueous solutions during freezing to -60 degrees C and subsequent heating to +20 degrees C. The concentration of proline in the freeze concentrated solution was estimated to approximately 50 wt% (w...

  13. Modeling flavor release from aqueous sucrose solutions, using mass transfer and partition coefficients

    NARCIS (Netherlands)

    Nahon, D.F.; Harrison, M.; Roozen, J.P.

    2000-01-01

    The penetration theory of interfacial mass transfer was used to model flavor release from aqueous solutions containing different concentrations of sucrose. The mass transfer coefficient and the gas/solution partition coefficient are the main factors of the model influencing the release in time. Para

  14. Electrical conductivity of aqueous solutions of perrhenic acid

    International Nuclear Information System (INIS)

    The physiocochemical properties of perrhenic acid, HReO4, are studied; its salts form the basis of solutions for electrochemical production of rhenium. Information is presented from which the electrical conductivity of solutions in the temperature range 15-90 degrees can be determined from known concentrations of the acid in water and vice versa

  15. Morphological modifications of selenium by recrystallization of its aqueous complex solutions.

    Science.gov (United States)

    Batabyal, Sudip K; Basu, C; Das, A R; Sanyal, G S

    2006-07-01

    Recrystallization of elemental selenium (Se) from aqueous solution in presence of sodium sulphite (Na2SO3) and sodium sulphide (Na2S) acting as complexing agents has resulted in the formation of nano and microstructures of Se having five different morphological modifications. (1) An aqueous solution of sodium selenosulphate (Na2SO3Se) obtained by dissolving Se in Na2SO3 under refluxing condition yields hemispherical microcrystals. (2) The filtrate of the above reaction mixture on aging produces hexagonal prismatic microrods of Se. Addition of Na2SO3Se solution to formalin (HCHO) at room temperature and refluxing conditions generates (3) Se nanorods, and (4) spherical microcrystals, respectively. (5) Recrystallization of Se from aqueous solution of Na2S develops flower shaped microcrystals.

  16. Reaction paths and equilibrium end-points in solid-solution aqueous-solution systems

    Science.gov (United States)

    Glynn, P.D.; Reardon, E.J.; Plummer, L.N.; Busenberg, E.

    1990-01-01

    Equations are presented describing equilibrium in binary solid-solution aqueous-solution (SSAS) systems after a dissolution, precipitation, or recrystallization process, as a function of the composition and relative proportion of the initial phases. Equilibrium phase diagrams incorporating the concept of stoichiometric saturation are used to interpret possible reaction paths and to demonstrate relations between stoichiometric saturation, primary saturation, and thermodynamic equilibrium states. The concept of stoichiometric saturation is found useful in interpreting and putting limits on dissolution pathways, but there currently is no basis for possible application of this concept to the prediction and/ or understanding of precipitation processes. Previously published dissolution experiments for (Ba, Sr)SO4 and (Sr, Ca)C??O3orth. solids are interpreted using equilibrium phase diagrams. These studies show that stoichiometric saturation can control, or at least influence, initial congruent dissolution pathways. The results for (Sr, Ca)CO3orth. solids reveal that stoichiometric saturation can also control the initial stages of incongruent dissolution, despite the intrinsic instability of some of the initial solids. In contrast, recrystallisation experiments in the highly soluble KCl-KBr-H2O system demonstrate equilibrium. The excess free energy of mixing calculated for K(Cl, Br) solids is closely modeled by the relation GE = ??KBr??KClRT[a0 + a1(2??KBr-1)], where a0 is 1.40 ?? 0.02, a1, is -0.08 ?? 0.03 at 25??C, and ??KBr and ??KCl are the mole fractions of KBr and KCl in the solids. The phase diagram constructed using this fit reveals an alyotropic maximum located at ??KBr = 0.676 and at a total solubility product, ???? = [K+]([Cl-] + [Br-]) = 15.35. ?? 1990.

  17. A chemical probe technique for the determination of reactive halogen species in aqueous solution: Part 2 – chloride solutions and mixed bromide/chloride solutions

    Directory of Open Access Journals (Sweden)

    C. Anastasio

    2006-02-01

    Full Text Available Although reactive halogen species (X*=X●, ●X2−, X2 and HOX, where X=Br, Cl, or I are important environmental oxidants, relatively little is known about their kinetics in condensed phases such as seawater and sea-salt particles. Here we describe a new technique to determine reactive chlorine and bromine species in aqueous solutions by using allyl alcohol (CH2=CHCH2OH as a chemical probe. This probe is combined with competition kinetics in order to determine steady state concentrations of X*(aq. In some cases the technique also can be used to determine the rates of formation and lifetimes of X* in aqueous solution. In a companion paper we reported the results of our method development for aqueous solutions containing only bromide (Br−. In this paper, we discuss method development for solutions containing chloride (Cl− alone, and for solutions containing both bromide and chloride.

  18. Release of fission products from oxidised zircaloy cladding in contact with an alkaline solution

    International Nuclear Information System (INIS)

    Before nuclear spent fuel reprocessing, the cladding tubes are sectioned into pieces called hulls in order to release the UO2 pellets. The hulls are collected as solid wastes and were embedded inside a concrete structure until 1995. In the perspective of geological storage, a great interest is given to iodine release during contact between hulls and basic water infiltrated inside the concrete structure. Experiments were performed on zircaloy or zirconium oxidised samples representative of oxidised hulls surfaces. Corrosion tests were performed in autoclave. The specimens were exposed to a basic solution at 250 deg C, 275 deg C and 300 deg C. The corrosion tests were conducted during 12 weeks with regular sampling every two weeks. The partial dissolution of the oxide coating was studied using the rare earth europium element as a surface marker of zirconia. Such a choice is based on experimental results ensuring that this marker will not diffuse in the 250-300 deg C temperature range. Europium was introduced by ion implantation (Rp = 42 nm). The evolutions of europium concentration profiles measured at each corrosion step show that a non homogeneous dissolution of zirconia occurs in this alkaline medium. The mean dissolution rate is equal to 1 nm/day at 300 deg C. In order to analyse the mechanism involved in iodine migration, iodine atoms were introduced in samples by ion implantation. The iodine profile evolution allows to identify two steps in iodine release. A rapid desorption which could not be related to zirconia dissolution and then a stabilisation as far as low the iodine concentration (0.3 at.%) were reached. We demonstrated that hydrogen (representative of hydroxyl) migration in zirconia is clearly enhanced by the presence of iodine in the sample and that the iodine release is correlated to that of hydroxyl ions. The correlation of the behaviour between iodine and hydroxyl ions could be explained by the creation of complexes. (author)

  19. Succinic acid in aqueous solution : connecting microscopic surface composition and macroscopic surface tension

    OpenAIRE

    Werner, Josephina; Julin, Jan; Dalirian, Maryam; Prisle, Nønne; Öhrwall, Gunnar; Persson, Ingmar; Björneholm, Olle; Riipinen, Ilona

    2014-01-01

    The water vapor interface of aqueous solutions of succinic acid, where pH values and bulk concentrations were varied, has been studied using surface sensitive X-ray photoelectron spectroscopy (XPS) and molecular dynamics (MD) simulations. It was found that succinic acid has a considerably higher propensity to reside in the aqueous surface region than its deprotonated form, which is effectively depleted from the surface due to the two strongly hydrated carboxylate groups. From both XPS experim...

  20. Strontium separation with ultrafiltration membranes from dilute aqueous solutions

    International Nuclear Information System (INIS)

    The separation of Sr2+ from dilute and trace solutions of low activity by means of hollow fiber Amicon ultrafiltration membranes is studied. The cation is absorbed on colloidal particles of titanium oxide formed directly in solution, and the coloidal dispersion is filtrated. The method has been studied under several different operative conditions (pH, Ti/Sr ratio, the presence of interfering ions, colloid formation time) with the aim of determining the optimum conditions to develop a separation process

  1. Application of the Ozonation Pre-treatment for Biodegradation of Aqueous Solutions of Methyltert-Butyl Ether

    Directory of Open Access Journals (Sweden)

    M. Sadeghi

    2005-01-01

    Full Text Available The effectiveness of ozone treatment for improving the biodegradability of recalcitrant pollutants has been proved by investigating the ozonation reaction of Methyl tert-butyl ether (MTBE a bioresistant gasoline oxygenate. Laboratory scale experiments have been carried out, at room temperature, by bubbling, for 120 min, ozonated air (3.4 ppm min-1 into 3 liter of an alkaline (pH=11.5 aqueous solution (100 mg L-1 of MTBE. The experimental results indicated that during the ozonation, complete MTBE degradation occurs in 100 min and after this time, ozone consumption goes on very slowly. At the end of the ozonation, after 100 min, the initial value of COD (256 mg O2 L-1 is 98 and correspond to a relative removal of about 62%.As for MTBE solution biodegradability expressed as (BOD5/(COD ratio, during the first 90 min its value regularly increases from lowest (0.01 up to a maximum of 0.68 that corresponds to an ozone consumption of 1.25 mg per each mg of COD initially present in the solution.The experimental results for determining the rate of MTBE removal due to stripping showed that about 14% of MTBE strips out after an hour of sparging with oxygen gas. The fraction of MTBE oxidized and/or striped increases to about 28% (in pH=7 and 70% (in pH=11.5 with ozonation over the same time period.

  2. Stability of peptides in high-temperature aqueous solutions

    Science.gov (United States)

    Shock, Everett L.

    1992-09-01

    Estimated standard molal thermodynamic properties of aqueous dipeptides and their constituent amino acids indicate that temperature increases correspond to increased stability of peptide bonds relative to hydrolysis reactions. Pressure increases cause slight decreases in peptide bond stability, which are generally offset by greater stability caused by temperature increases along geothermal gradients. These calculations suggest that peptides, polypeptides, and proteins may survive hydrothermal alteration of organic matter depending on the rates of the hydrolysis reactions. Extremely thermophilic organisms may be able to take advantage of the decreased energy required to form peptide bonds in order to maintain structural proteins and enzymes at elevated temperatures and pressures. As the rates of hydrolysis reactions increase with increasing temperature, formation of peptide bonds may become a facile process in hydrothermal systems and deep in sedimentary basins.

  3. Pulse radiolysis study on tetra-alkylammonium hydroxides in alkaline solutions containing 02 and N20

    International Nuclear Information System (INIS)

    The reactivity of the oxide radical ion 0- and the decay kinetics of the ozonide ion, 03-, have been investigated in aqueous solutions at pH 12.8 in the presence of tetramethyl-, tetraethyl-, tetrapropyl-, and tetrabutylammonium ions, 02 and N20. Using pulse radiolysis to follow the 03- kinetics gives information on the competition of 02 and R4N+ for 0-. Absolute rate constants for these reactions are: 3.0 x 108 dm3 mol-1 s-1 for 0- + (CH3)4N+, 1.0 x 109 dm3 mol-1 s-1 for 0- + (C2H5)4N+, 1.3 x 109 dm3 mol-1 s-1 for 0- + (C3H7)4N+ and 2.2 x 109 dm3 mol-1 s-1 for O- + (C4H9)4N+. The decay of 03- occurs through the thermal dissociation reaction, 03 →(reversible) 02 + 0-, for which the absolute rate constant at 220C was found to be 6.2 +- 1.2 x 103 s-1. (author)

  4. Equilibrium Studies of Some Metal Ions onto Modified Orange Mesocarp Extract in Aqueous Solution

    OpenAIRE

    Ibezim-Ezeani, Millicent U.; Okoye, Francis A.; Akaranta, Onyewuchi

    2012-01-01

    This paper examines the equilibrium removal of Zinc, Copper, Nickel and Cobalt ions from aqueous solutions by cation exchange resins synthesized using orange mesocarp extract. The percentage metal ion exchange of Carboxylated-Toluene Di-isocyanate Orange Mesocarp Extract Resin (CTOR) increased with increase in pH of the solution phase, while that of Sulphonated-Toluene Di-isocyanate Orange Mesocarp Extract Resin (STOR) was relatively uniform with increase in solution pH. The results also show...

  5. Radiation induced degradation of ketoprofen in dilute aqueous solution

    International Nuclear Information System (INIS)

    The intermediates and final products of ketoprofen degradation were investigated in 0.4 mmol dm−3 solution by pulse radiolysis and gamma radiolysis. For observation of final products UV−vis spectrophotometry and HPLC separation with diode array detection were used, and for identification MS was used. The reactions of •OH lead to hydroxycyclohexadienyl type radical intermediates, in their further reactions hydroxylated derivatives of ketoprofen form as final products. The hydrated electron is scavenged by the carbonyl oxygen and the electron adduct protonates to ketyl radical •OH is more effective in decomposing ketoprofen than hydrated electron. Chemical oxygen demand and total organic carbon content measurements on irradiated aerated solutions showed that using irradiation technology ketoprofen can be mineralised. The initial toxicity of the solution monitored by the Daphnia magna test steadily decreases with irradiation. Using 5 kGy dose no toxicity of the solution was detected with this test. - Highlights: ► In •OH reactions hydroxylated derivatives of ketoprofen form as stable products. ► •OH is more effective in decomposing ketoprofen than hydrated electron. ► Toxicity of the ketoprofen solution decreases with irradiation.

  6. Detecting the Biopolymer Behavior of Graphene Nanoribbons in Aqueous Solution

    Science.gov (United States)

    Wijeratne, Sithara S.; Penev, Evgeni S.; Lu, Wei; Li, Jingqiang; Duque, Amanda L.; Yakobson, Boris I.; Tour, James M.; Kiang, Ching-Hwa

    2016-01-01

    Graphene nanoribbons (GNR), can be prepared in bulk quantities for large-area applications by reducing the product from the lengthwise oxidative unzipping of multiwalled carbon nanotubes (MWNT). Recently, the biomaterials application of GNR has been explored, for example, in the pore to be used for DNA sequencing. Therefore, understanding the polymer behavior of GNR in solution is essential in predicting GNR interaction with biomaterials. Here, we report experimental studies of the solution-based mechanical properties of GNR and their parent products, graphene oxide nanoribbons (GONR). We used atomic force microscopy (AFM) to study their mechanical properties in solution and showed that GNR and GONR have similar force-extension behavior as in biopolymers such as proteins and DNA. The rigidity increases with reducing chemical functionalities. The similarities in rigidity and tunability between nanoribbons and biomolecules might enable the design and fabrication of GNR-biomimetic interfaces. PMID:27503635

  7. Corrosion fatigue behavior of high strength brass in aqueous solutions

    Energy Technology Data Exchange (ETDEWEB)

    Hamada, A.S.; Kassem, M.A.; Ramadan, R.M.; El-Zeky, M.A. [Suez Canal Univ., Dept. of Metallurgy and Materials Engineering (Egypt)

    2000-07-01

    Corrosion fatigue behavior of British Standard high strength brass, CZ 127 has been studied in various environments, 3.5%NaC1 solution and 3.5%NaC1 containing 1000ppm ammonia by applying the reverse bending technique, strain-controlled cyclic, at 67 cycles/min. Characteristics of the produced alloy were studied using differential thermal analysis with applying its results in heat treating of the alloy; metallographic examinations; hardness measurements; X-ray; and electrochemical behavior of the unstressed alloy. CZ 127 was fatigued at three different conditions, solution treated, peak aged, and over aged at a fixed strain amplitude, 0.03 5. Solution treated alloy gave the best fatigue properties in all environments tested among the other materials. Results of the alloy studied were compared with that obtained of 70/30 {alpha}-brass. Fracture surface of the fatigued alloy was examined using optical microscope and scanning electron microscope equipped with EDX. (author)

  8. Detecting the Biopolymer Behavior of Graphene Nanoribbons in Aqueous Solution.

    Science.gov (United States)

    Wijeratne, Sithara S; Penev, Evgeni S; Lu, Wei; Li, Jingqiang; Duque, Amanda L; Yakobson, Boris I; Tour, James M; Kiang, Ching-Hwa

    2016-01-01

    Graphene nanoribbons (GNR), can be prepared in bulk quantities for large-area applications by reducing the product from the lengthwise oxidative unzipping of multiwalled carbon nanotubes (MWNT). Recently, the biomaterials application of GNR has been explored, for example, in the pore to be used for DNA sequencing. Therefore, understanding the polymer behavior of GNR in solution is essential in predicting GNR interaction with biomaterials. Here, we report experimental studies of the solution-based mechanical properties of GNR and their parent products, graphene oxide nanoribbons (GONR). We used atomic force microscopy (AFM) to study their mechanical properties in solution and showed that GNR and GONR have similar force-extension behavior as in biopolymers such as proteins and DNA. The rigidity increases with reducing chemical functionalities. The similarities in rigidity and tunability between nanoribbons and biomolecules might enable the design and fabrication of GNR-biomimetic interfaces. PMID:27503635

  9. Radiolysis of Reactive Azo Dyes in Aqueous Solution

    Directory of Open Access Journals (Sweden)

    Agustin N.M. Bagyo

    2004-07-01

    Full Text Available The effects of radiation on aerated reactive dye solutions i.e Cibacron Violet, Cibacron Orange and Cibacron Yellow solutions have been studied. Parameters analysis were the change of pH after radiation, the change of absorption, degradation products and effects of pH on the radiolysis. The uv-vis absorption of solutions were observed before and after irradiation. pH variation was done from pHs 3, 5, 7, 9 and 12. Irradiation was done at doses of 0, 2, 4, 6, 8 and 10 kGy with dose rate of 5 kGy/h and was determined by a Fricke dosimeter. HPLC with UV detector was used to analyze the degradation products. Oxalic acid was the main degradation product and small amount of succinic acid was also detected.

  10. Partition Equilibrium Between Charged Membrane and Single Electrolyte Aqueous Solution

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Ionic partition equilibrium in charged membrane immersed in solution of single electrolyte with mono valence or multi-valence is systematically investigated and several expressions are established for determination of partition coefficients. On this basis, the effects of the ratio of membrane charge density to bulk electrolyte solution concentration, the charge sign and valence of electrolyte ions and the type of membrane on the partition equilibrium were analyzed and simulated within chosen parameters. It is revealed that ion partition is not related solely with the respective concentrations but also definitely with the concentration ratio of fixed group to bulk solution in addition to the charge sign and the valence. For a counterion, the partition coefficient increases with this ratio and the valence; while for a coion, the partition coefficient decreases with this ratio and the valence. The theoretical calculations were compared with the experimental data and a good agreement was observed.

  11. Partition Equilibrium Between Charged Membrane and Single Electrolyte Aqueous Solution

    Institute of Scientific and Technical Information of China (English)

    徐铜文; 杨伟华; 何柄林

    2001-01-01

    Ionic partition equilibrium in charged membrane immersed in solution of single electrolyte with monovalence or multi-valence is systematically investigated and several expressions are established for determination of partition coefficients. On this basis, the effects of the ratio of membrane charge density to hulk electrolyte solution concentration, the charge sign and valence of electrolyte ions and the type of membrane on the partition equilibrium were analyzed and simulated with in chosen parameters. It is revealed that ion partition is not related solely withthe respective concentrations but also definitely with the concentration ratio of fixed group to bulk solution in addition to the charge sign and the valence. For a counterion, the partition coefficient increases with this ratio and the valence; while for a coion, the partition coefficient decreases with this ratio and the valence. The theoreticalcal culations were compared with the experimental data and a good agreement was observed.

  12. Reversible Sol-Gel Transitions in Aqueous Solutions of N-Isopropylacrylamide Ionic Copolymers

    Energy Technology Data Exchange (ETDEWEB)

    Krzyminski, Karol J.; Jasionowski, Marek; Gutowska, Anna

    2008-04-01

    Ionic copolymers of N-isopropylacrylamide (NIPA) exhibiting sol-gel transitions in aqueous solutions were investigated. The studies were aimed at understanding of the structure-property relationship in design of injectable, in situ forming gels for potential biomedical applications in delivery of therapeutics and tissue engineering. Aqueous solutions of NIPA ionic copolymers were found to flow freely at ambient temperatures and formed soft gels with controlled syneresis above 32°C, the lower critical solution temperature of NIPA. The sol-gel transitions and temperature dependent properties of the resulting gels were analyzed using dynamic rheometry, UV and IR spectrometry, and were found to be controlled by the molecular weight and composition of copolymers, ionization state of comonomers, and composition of aqueous solvent.

  13. Synthesis of polyamidoxime-functionalized nanoparticles for uranium(VI) removal from neutral aqueous solutions

    International Nuclear Information System (INIS)

    It is important to separate uranium(VI) from water environment due to its high toxicity and radioactivity. A new kind of polystyrene nanoparticles with polyamidoxime is reported here for removal of uranium(VI) from aqueous solutions. The obtained PSt nanoparticles have a tunable sorption capacity. The sorption process follows pseudo-second-order kinetics, and the equilibrium can be reached within 6 h. Furthermore, the optimal pH value of sorption process is 6.5, and the adsorbents can be recycled well for uranium(VI) sorption from aqueous solution. This work indicates that the polyamidoxime-functionalized PSt nanoparticles may be used as a good adsorbent for the removal of uranium(VI) from neutral aqueous solution. (author)

  14. Detection of copper ions from aqueous solutions using layered double hydroxides thin films deposited by PLD

    Science.gov (United States)

    Vlad, A.; Birjega, R.; Matei, A.; Luculescu, C.; Nedelcea, A.; Dinescu, M.; Zavoianu, R.; Pavel, O. D.

    2015-10-01

    Layered double hydroxides (LDHs) thin films with Mg-Al were deposited using pulsed laser deposition (PLD) technique. We studied the ability of our films to detect copper ions in aqueous solutions. Copper is known to be a common pollutant in water, originating from urban and industrial waste. Clay minerals, including layered double hydroxides (LDHs), can reduce the toxicity of such wastes by adsorbing copper. We report on the uptake of copper ions from aqueous solution on LDH thin films obtained via PLD. The obtained thin films were characterized using X-ray Diffraction, Atomic Force Microscopy, and Scanning Electron Microscopy with Energy Dispersive X-ray analysis. The results in this study indicate that LDHs thin films obtained by PLD have potential as an efficient adsorbent for removing copper from aqueous solution.

  15. APPLICATION OF NONIONIC TEMPERATURE SENSITIVE HYDROGEL FOR CONCENTRATION OF PROTEIN AQUEOUS SOLUTION

    Institute of Scientific and Technical Information of China (English)

    SUN Yishi; QIU Zhiyong; HONG Yaoliang

    1992-01-01

    Six different N-alkyl substituted acrylamide nonionic hydrogels were prepared and their swelling characteristics were measured. Poly N-isopropyl acrylamide (PNIPA) and poly N-n-propylacrylamide (PNNPA) temperature sensitive hydrogels were chosen as the nonionic temperature sensitive hydrogels for concentration of very dilute aqueous protein solution. The separation properties of PNIPA and PNNPA hydrogels with different network dimensions were studied and the modification of the hydrogels was surveyed in order to decrease their surface adsorption of protein molecules. The experimental results of the concentration of BSA (Bovin serum albumin) dilute aqueous solution by hydroxylpropyl methacrylate (HPMA) copolymerized PNIPA hydrogel were given. The value and the limitation of concentration of dilute aqueous protein solution by this method was evaluated.

  16. Standard enthalpies of formation of α-aminobutyric acid and products of its dissociation in an aqueous solution

    Science.gov (United States)

    Lytkin, A. I.; Chernikov, V. V.; Krutova, O. N.

    2016-08-01

    Heats of solution of crystalline α-aminobutyric acid in water and in aqueous solutions of potassium hydroxide at 298.15 K are measured by means of direct calorimetry. Standard enthalpies of formation of the amino acid and products of its dissociation in an aqueous solution are calculated.

  17. systematic investigation of foam separation of nickel (l l) from dilute aqueous solutions, precipitate flotation of nickel(l l) hydroxide

    International Nuclear Information System (INIS)

    the foam separation of Ni (l l) from dilute aqueous solutions was investigated by precipitate flotation of nickel (l l) hydroxide from alkaline aqueous suspensions using the anionic surfactant sodium lauryl sulphate (Nals) and the cationic one , cetyl trimethyl ammonium bromide (CTAB), as collectors. the main parameters affecting the process in batch experiments were examined. nals was found to be effective at Ph values below the isoelectric point of the hydroxide precipitate ∼ 11 removals >99% were obtained at the optimum operating conditions . CTAB could float Ni (OH)2 at Ph values >11. effects of foreign ions and of adsorption of the collectors by the hydroxide as well as their removal by the flotation process were also studied. the interpretation of the results is based on the analysis of possible chemical and electrostatic interactions between the ionized surfactant sites on the precipitate, active groups of the collector and type and concentration of electrolyte ions

  18. Selected specific rates of reactions of transients from water in aqueous solution. Hydrated electron, supplemental data. [Reactions with transients from water, with inorganic solutes, and with solutes

    Energy Technology Data Exchange (ETDEWEB)

    Ross, A.B.

    1975-06-01

    A compilation of rates of reactions of hydrated electrons with other transients and with organic and inorganic solutes in aqueous solution appeared in NSRDS-NBS 43, and covered the literature up to early 1971. This supplement includes additional rates which have been published through July 1973.

  19. Biosorption of strontium from aqueous solutions onto spent coffee grounds

    International Nuclear Information System (INIS)

    A set of experiments was carried out to evaluate the strontium uptake potential of spent coffee grounds (SCG) by batch tests in aqueous medium. Adsorption of Sr2+ as a function of contact time and adsorbent dose, pH, particles size, agitation speed, temperature and co-ions presence was investigated. Obtained results revealed that the maximum adsorption took place at pH range of 5-8 and temperature values between 283 and 333 K. Particles size effect was not very significant and agitation speed influenced on the equilibrium time. Competitive adsorption experiments allowed us to classify the negative effect on the Sr2+ uptake according to this order Al3+ ≫ Co2+ > Mg2+ > Ca2+ ≫ Na+ > K+ > Cs+. Kinetic study indicated that the Sr2+ uptake was fast and it was well fitted by the pseudo second order reaction model. Adsorption isotherm was well interpreted by Langmuir model. The maximum adsorption capacity was found to be 69.01 mg g−1 at pH 7, 293 K, particles sizes = 200-400 μm and agitation speed 250 rpm. The thermodynamic study revealed that the process was spontaneous (ΔG0 0 2+ (ΔG0 0 > 0) and occurred by physical adsorption (Ea = 8.37 kJ mol-1). FTIR analysis showed carboxylic acid and amino group presence on SCG surface playing a vital role in Sr2+ biosorption. (author)

  20. Study of Penetration Kinetics of Sodium Hydroxide Aqueous Solution into Wood Samples

    Directory of Open Access Journals (Sweden)

    Lubomír Lapčík

    2013-12-01

    Full Text Available The kinetics of unidirectional penetration of NaOH aqueous solution into rectangular samples of wood oriented parallel to a stern axis were studied. Scots pine (Pinus sylvestris, European larch (Larix decidua, blackthorn (Prunus spinosa, white willow (Salix alba, and horse-chestnut wood (Aesculus hippocastanum were studied in this work. The time dependence of liquid incorporation was measured by the volumetric method as a change of total volume of coexisting liquid (NaOH/H2O phase. The total thickness of the swollen surface layer d and mean value of the apparent diffusion coefficient of aqueous NaOH solution at 22 °C were determined.

  1. Label-free monitoring of interaction between DNA and oxaliplatin in aqueous solution by terahertz spectroscopy

    Science.gov (United States)

    Wu, Xiaojun; E, Yiwen; Xu, Xinlong; Wang, Li

    2012-07-01

    We demonstrated the feasibility of applying terahertz time-domain spectroscopy (THz-TDS) to monitor the molecular reactions in aqueous solutions of anticancer drug oxaliplatin with λ-DNA and macrophages DNA. The reaction time dependent refractive index and absorption coefficient were extracted and analyzed. The reaction half-decaying time of about 4.0 h for λ-DNA and 12.9 h for M-DNA was established. The results suggest that the THz-TDS detection could be an effective label-free technique to sense the molecular reaction in aqueous solutions and could be very useful in biology, medicine, and pharmacy industry.

  2. REMOVAL OF CONGO RED DYE FROM AQUEOUS SOLUTION BY DATE PALM LEAF BASE

    OpenAIRE

    Ghadah Alsenani

    2014-01-01

    Removal of dyes from wastewater is important for industry and environmental protection. The adsorption technique, using biomass is attractive method for environmental and economical reasons. This study studies removal of Congo Red dye (CR) from aqueous solutions by adsorption using date palm Leaf Base (LB). The adsorption of congo red dye CR onto LB has been examined in aqueous solution by considering the influence of temperature up to 60°C and pH on the percentage removal of CR. The resu...

  3. Removal of Indigo Carmine Dye from Aqueous Solution Using Magnesium Hydroxide as an Adsorbent

    OpenAIRE

    Thimmasandra Narayan Ramesh; Vani Pavagada Sreenivasa

    2015-01-01

    Magnesium hydroxide is used as an adsorbent for the removal of indigo carmine dye from aqueous solution. We have investigated the effectiveness of removal of indigo carmine dye from aqueous solutions at pH 6-7 and 12-13 using magnesium hydroxide thereby varying the dose of the adsorbent, concentration of the dye, duration, and temperature. Structural transformations of adsorbent during the adsorption process at different pH values are monitored using powder X-ray diffraction and infrared spec...

  4. Sorption Potentials of Waste Tyre for Some Heavy Metals (Pb Cd) in Aqueous Solution

    OpenAIRE

    Austin Kanayo ASIAGWU; Patrice-Anthony-Chudi OKOYE; Orji IFEOMA; Patrick Ejo OMUKU

    2009-01-01

    An investigation into the adsorption potential of activated and inactivated waste tyre powders for some heavy metals (Pb2+ and Cd2+) in their aqueous solution has been studied. The result indicated that inactivated waste tyre is a good non-conventional adsorbent for the removal of Cd from aqueous solution. A total of 93.3% of Cadmium contents was removed. The inactivated waste type proved a good adsorbent for the removal of Pb2+ 5g of 500mm activated tyre removed over 86.66% of Pb2+ from solu...

  5. Cooling and Freezing Behaviors of Aqueous Sodium Chloride Solution in a Closed Rectangular Container

    Science.gov (United States)

    Narumi, Akira; Kashiwagi, Takao; Nakane, Ichirou

    This paper investigates cooling and freezing behaviors of NaCl aqueous solution in a rectangular container equipped with horizontal partitions of micro porous film in order to determine the mechanisms of heat and mass transfer through cell wall for the purpose of freezing food. For comparison, experiments were performed using partitions of copper plate, no partition, and water. These processes were visualized and measured using real-time laser holographic interferometry. It was found that there was very little difference in the cooling process due to partitions, but that there were significant differences in freezing process when NaCl aqueous solution is used.

  6. Ludwig-Soret effect of non-ionic surfactant aqueous solution studied by beam deflection method

    Science.gov (United States)

    Maeda, Kousaku; Kita, Rio; Shinyashiki, Naoki; Yagihara, Shin

    2013-02-01

    We have studied the thermal diffusion of non-ionic surfactant aqueous solutions by a beam deflection method. The thermal diffusion of pentaethylene glycol monododecyl ether (C12E5) and hexaethylene glycol monododecyl ether (C12E6) is studied in the concentration range of 1.0-99.0 wt% and in the temperature range of 20.0-35.0 °C. A stable temperature gradient is applied to the solution, where solute molecules shift to the cold side of the solution for lowconcentration samples. The concentration dependence of the Soret coefficient ST of the C12E6 aqueous solution shows a sign inversion behavior. At all concentrations, the developed concentration gradient is proportionally related to the applied temperature gradient. The results confirm that the magnitude of ST has no temperature gradient dependence under the studied experimental conditions.

  7. investigations for the separation of radioisotopes and selected metal ions from dilute aqueous solutions and aqueous waste simulant by foaming

    International Nuclear Information System (INIS)

    co precipitate flotation (CPF) investigations show that cesium can be efficiently separated from aqueous solutions by coprecipitation with zine hexacyanoferrate (II) (ZnHCF) and subsequent flotation of the precipitate . collectors of different types were tested but cetyl pyridinium chloride showed the best performance. before undertaking the flotation investigations , coprecipitation of Cs with ZnHCF was studied to determine the optimal coprecipitation conditions. the developed CPF process was applied successfully for 137Cs removal from process wastewater and low level liquid radioactive waste simulant. the obtained results compare favourably with data published for cesium removal by coprecipitation or adsorption processes. besides, CPF seems to be more advantageous

  8. Toward stable nickel catalysts for aqueous phase reforming of biomass-derived feedstock under reducing and alkaline conditions

    NARCIS (Netherlands)

    Haasterecht, van T.; Ludding, C.C.I.; Jong, de K.P.; Bitter, J.H.

    2014-01-01

    Nickel nanoparticles supported on carbon nanofibers (CNF) can be stabilized in aqueous phase processes at elevated temperatures and pressures by tuning the reaction conditions to control Ni oxidation and leaching. As a showcase, Ni/CNF was used for the production of hydrogen via aqueous phase reform

  9. Design and characterization of multicompartment micelles in aqueous solution

    OpenAIRE

    Kubowicz, Stephan

    2005-01-01

    Self-assembly of polymeric building blocks is a powerful tool for the design of novel materials and structures that combine different properties and may respond to external stimuli. In the past decades, most studies were focused on the self-assembly of amphiphilic diblock copolymers in solution. The dissolution of these block copolymers in a solvent selective for one block results mostly in the formation of micelles. The micellar structure of diblock copolymers is inherently limited to a homo...

  10. Surfactant-free exfoliation of graphite in aqueous solutions.

    Science.gov (United States)

    Ricardo, Karen B; Sendecki, Anne; Liu, Haitao

    2014-03-14

    We report an ultrasound exfoliation of graphite in a weakly basic solution to produce multi-layer graphene dispersion. A unique feature of this process is that no surfactant was added to stabilize the exfoliated graphene in water. The concentration of the graphene dispersion prepared by this approach can be up to 0.02 mg mL(-1) and it was stable at room temperature for several months.

  11. Criticality in aqueous solutions of 3-methylpyridine and sodium bromide.

    Science.gov (United States)

    Kostko, A F; Anisimov, M A; Sengers, J V

    2004-08-01

    We address a controversial issue regarding the nature of critical behavior in ternary electrolyte solutions of water, 3-methylpyridine, and sodium bromide. Earlier light-scattering studies showed an anomalous critical behavior in this system that was attributed to the formation of a microheterogeneous phase associated with ion-molecule clustering [M.A. Anisimov, J. Jacob, A. Kumar, V.A. Agayan, and J. V. Sengers, Phys. Rev. Lett. 85, 2336 (2000)

  12. Comparative analysis of the effect of pretreating aspen wood with aqueous and aqueous-organic solutions of sulfuric and nitric acid on its reactivity during enzymatic hydrolysis

    DEFF Research Database (Denmark)

    Dotsenko, Gleb; Osipov, D. O.; Zorov, I. N.;

    2016-01-01

    The effect of aspen wood pretreatment methods with the use of both aqueous solutions of sulfuric and nitric acids and aqueous-organic solutions (ethanol, butanol) of sulfuric acid (organosolv) on the limiting degree of conversion of this type of raw material into simple sugars during enzymatic...... of ground wood by 300–400%, compared to the initial raw material. Pretreatment with a 4.8% aqueous solution of nitric acid (125°C, 1.8 MPa, 10 min) is shown to be most effective, as it increases the reactivity of the ground aspen wood by more than 500%....

  13. Chemical behaviour of plutonium in aqueous chloride solutions

    International Nuclear Information System (INIS)

    The chemical behaviour of Plutonium has been investigated in concentrated NaCl solutions in the neutral pH range. The α-radiation induced radiolysis reactions oxidize the Cl--ion to Cl2, HClO, ClO- and other species, which produce a strongly oxidizing medium. Under these conditions the Pu ions of lower oxidation states are readily oxidized to Pu(VI), which then undergo depending on the pH of the solution, various chemical reactions to produce PuO2Cln, PuO2(ClO)m or PuO2(OH)x species. In addition to primary radiolysis reactions taking place in NaCl solutions, the reactions leading to the PuO2(Cl)n and PuO2(ClO)m species have been characterized and quantified systematically by spectroscopic and thermodynamic evaluation. The redox and complexation reactions of Pu ions under varying NaCl concentration, specific α-activity and pH are discussed. (orig.)

  14. Interfacial structures of acidic and basic aqueous solutions

    International Nuclear Information System (INIS)

    Phase-sensitive sum-frequency vibrational spectroscopy was used to study water/vapor interfaces of HCl, HI, and NaOH solutions. The measured imaginary part of the surface spectral responses provided direct characterization of OH stretch vibrations and information about net polar orientations of water species contributing to different regions of the spectrum. We found clear evidence that hydronium ions prefer to emerge at interfaces. Their OH stretches contribute to the 'ice-like' band in the spectrum. Their charges create a positive surface field that tends to reorient water molecules more loosely bonded to the topmost water layer with oxygen toward the interface, and thus enhances significantly the 'liquid-like' band in the spectrum. Iodine ions in solution also like to appear at the interface and alter the positive surface field by forming a narrow double-charge layer with hydronium ions. In NaOH solution, the observed weak change of the 'liquid-like' band and disappearance of the 'ice-like' band in the spectrum indicates that OH- ions must also have excess at the interface. How they are incorporated in the interfacial water structure is however not clear

  15. The Unusual Conformational Behavior of Polyzwitterionic Brushes in Aqueous Solutions

    Science.gov (United States)

    Mao, Jun; Chen, Wei; Yuan, Guangcui; Yu, Jing; Tirrell, Matthew

    Polyzwitterions constitute a peculiar class of polyelectrolytes, which are electrically neutral polymers containing both a positive and a negative charge on each repeating unit. Surfaces coated with polyzwitterionic brushes are resistant to the nonspecific accumulation of proteins and microorganisms, making them excellent candidates for a wide range of antifouling applications, from biocompatible medical devices to marine coatings. The surrounding environment can dramatically influence the conformational behavior of polyzwitterionic brushes. High-density polyzwitterionic brushes poly(2-methacryloyloxyethyl phosphorylcholine) (PMPC) were synthesized using surface initiated atom-transfer radical polymerization, and neutron reflectivity (NR) measurements were performed to investigate the ionic strength dependence of the conformational behaviors of PMPC brushes in monovalent salt solutions. Despite the numerous observations of normal pure polyelectrolyte brushes, NR results showed that both the densely concentrated layer near the substrate surface and the relatively swollen layer into the solution have been observed in different q range in a single neutron reflectivity profile. These results will definitely help us to better understand the relationship between the solution behaviors of zwitterionic polymer brushes and their antifouling properties.

  16. Electrosprayed molybdenum trioxide aqueous solution and its application in organic photovoltaic cells.

    Science.gov (United States)

    Suzuki, Katsumi; Fukuda, Takeshi; Liao, Yingjie

    2014-01-01

    A molybdenum trioxide thin film with smooth surface and uniform thickness was successfully achieved by an electrospray deposition method using an aqueous solution with a drastically low concentration of 0.05 wt%. Previous papers demonstrated that an additive solvent technique is useful for depositing the thin film by the electrospray deposition, and the high vapor pressure and a low surface tension of an additive solvent were found to be important factors. As a result, the smooth molybdenum trioxide thin film was obtained when the acetonitrile was used as the additive solvent. Furthermore, the vapor pressure of acetone is much higher than that of aqueous solution, and this indicates that the acetone is easily evaporated after spraying from the glass capillary. By optimizing a concentration of acetone in the molybdenum aqueous solution, a minimum root mean square roughness of the MoO3 thin film became 3.7 nm. In addition, an organic photovoltaic cell was also demonstrated using the molybdenum trioxide as a hole transport layer. Highest photoconversion efficiency was 1.72%, a value comparable to that using conventional thermal evaporation process even though the aqueous solution was used for the solution process. The photovonversion efficiency was not an optimized value, and the higher value can be achieved by optimizing the coating condition of the active layer.

  17. Electrosprayed molybdenum trioxide aqueous solution and its application in organic photovoltaic cells.

    Directory of Open Access Journals (Sweden)

    Katsumi Suzuki

    Full Text Available A molybdenum trioxide thin film with smooth surface and uniform thickness was successfully achieved by an electrospray deposition method using an aqueous solution with a drastically low concentration of 0.05 wt%. Previous papers demonstrated that an additive solvent technique is useful for depositing the thin film by the electrospray deposition, and the high vapor pressure and a low surface tension of an additive solvent were found to be important factors. As a result, the smooth molybdenum trioxide thin film was obtained when the acetonitrile was used as the additive solvent. Furthermore, the vapor pressure of acetone is much higher than that of aqueous solution, and this indicates that the acetone is easily evaporated after spraying from the glass capillary. By optimizing a concentration of acetone in the molybdenum aqueous solution, a minimum root mean square roughness of the MoO3 thin film became 3.7 nm. In addition, an organic photovoltaic cell was also demonstrated using the molybdenum trioxide as a hole transport layer. Highest photoconversion efficiency was 1.72%, a value comparable to that using conventional thermal evaporation process even though the aqueous solution was used for the solution process. The photovonversion efficiency was not an optimized value, and the higher value can be achieved by optimizing the coating condition of the active layer.

  18. Desalination of aqueous solutions by LTA and MFI zeolite membranes using pervaporation method

    Directory of Open Access Journals (Sweden)

    A. Malekpour

    2011-12-01

    Full Text Available LTA and MFI zeolite membranes were hydrothermally grown on the surface of an α-alumina porous support. The synthesized membranes were used for removal of cationic and anionic species from aqueous solutions by the pervaporation method. The perfection of the membranes was improved by employing the multi-stage synthesis method. The membranes were characterized by XRD, SEM and IR methods. The membranes were initially evaluated by the pervaporation separation of water from aqueous 2-propanol mixtures. The separation factors obtained were 7081 and 105 for NaA and ZSM-5 membranes, respectively. The ability of membranes for desalination of some aqueous solutions containing I-, Cs+ and Sr2+ ions was examined in various conditions. These ionic species were chosen because of their importance in the nuclear sciences. Both membranes effectively removed (more than 99 wt% I-, Cs+ and Sr2+ from their singlesalt solutions (0.001mol dm-3 over a temperature range of 298-338 K. The effects of parameters such as time and temperature on the separation factors and fluxes were investigated. This work shows that, due to their excellent chemical, thermal and mechanical stability, the zeolitic membranes are useful for desalination of aqueous solutions and treating saline wastewaters by pervaporation. Therefore, this method has the ability to desalinate harsh environment solutions involving strong solvent and radioactive components.

  19. Process of treating cellulosic membrane and alkaline with membrane separator

    Science.gov (United States)

    Hoyt, H. E.; Pfluger, H. L. (Inventor)

    1970-01-01

    The improvement of water-soluble cellulose ether membranes for use as separators in concentrated alkaline battery cells is discussed. The process of contacting membranes with an aqueous alkali solution of concentration less than that of the alkali solution to be used in the battery but above that at which the membrane is soluble is described.

  20. Modified carbon-free silver electrodes for the use as cathodes in lithium-air batteries with an aqueous alkaline electrolyte

    Science.gov (United States)

    Wittmaier, Dennis; Wagner, Norbert; Friedrich, K. Andreas; Amin, Hatem M. A.; Baltruschat, Helmut

    2014-11-01

    Gas diffusion electrodes with silver catalysts show a high activity towards oxygen reduction reaction in alkaline media but a rather poor activity towards oxygen evolution reaction. For the use in future lithium-air batteries with an aqueous alkaline electrolyte the activity of such electrodes must be improved significantly. As Co3O4 is a promising metal oxide catalyst for oxygen evolution in alkaline media, silver electrodes were modified with Co3O4. For comparison silver electrodes were also modified with IrO2. Due to the poor stability of carbon materials at high anodic potentials these gas diffusion electrodes were prepared without carbon support to improve especially the long-term stability. Gas diffusion electrodes were electrochemically investigated in an electrochemical half-cell arrangement. In addition to cyclic voltammograms electrochemical impedance spectroscopy (EIS) was carried out. SEM and XRD were used for the physical and morphological investigations. Investigations showed that silver electrodes containing 20 wt.% Co3O4 exhibited the highest performance and highest long-term stability. For comparison, rotating - ring - disc - electrode experiments have been performed using model electrodes with thin catalyst layers, showing that the amount of hydrogen peroxide evolved is negligible.

  1. Solvation of erbium(3) in aqueous dimethylsulfoxide solutions

    International Nuclear Information System (INIS)

    Solvation of Er3+ in aqua-dimethylsulfoxide solutions with concentration of DMSO from 0 to 89 mol.% was studied by electron spectroscopy method. Variation of Er3+ spectral characteristics during increasing DMSO concentration was demonstrated to be due to H2O -> DMSO substitution in first coordination sphere of Er3+, which was followed by strengthening of M-O bond with increasing covalence as well as distortion of coordination polyherdron. Concentration of DMSO in the H2O-DMSO mixture decreases with decline in radius of rare earth ion

  2. Biosorption of Mercury (II) from Aqueous Solutions onto Fungal Biomass

    OpenAIRE

    Víctor M. Martínez-Juárez; Juan F. Cárdenas-González; María Eugenia Torre-Bouscoulet; Ismael Acosta-Rodríguez

    2012-01-01

    The biosorption of mercury (II) on 14 fungal biomasses, Aspergillus flavus I–V, Aspergillus fumigatus I-II, Helminthosporium sp., Cladosporium sp., Mucor rouxii mutant, M. rouxii IM-80, Mucor sp 1 and 2, and Candida albicans, was studied in this work. It was found that the biomasses of the fungus M. rouxii IM-80, M. rouxii mutant, Mucor sp1, and Mucor sp 2 were very efficient removing the metal in solution, using dithizone, reaching the next percentage of removals: 95.3%, 88.7%, 80.4%, and 78...

  3. Standard method for colorimetric determination of technetium in aqueous solutions

    International Nuclear Information System (INIS)

    A colorimetric method is described for the determination of Tc in solutions from the processing of irradiated reactor fuels. The method is applicable to amounts of Tc from 5 to 200 μg/ml; however, the absorbance of the Tc-SCN complex in chloroform is linear from only 1 to 20 μg/ml of Tc in a 2-ml final volume. The complex absorbs at 513 nm, has a molar extinction coefficient of 46,000, and is stable for several hours. The method is highly specific for Tc

  4. Photo-degradation of chlorophenols in the aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Czaplicka, Marianna [Institute of Non-Ferrous of Metals, 44-100 Gliwice, Sowinskiego St. 5 (Poland)]. E-mail: mariannac@imn.gliwice.pl

    2006-06-30

    The review presents the chlorophenols photo-degradation kinetics and mechanism in the aquatic environment under UV-vis in the presence of hydroxyl radicals and singlet oxygen. The influence of experimental parameters e.g. pH, dissociation degree, presence of oxidants in solution, number and position of Cl atoms on the quantum yield and reaction rate constant of chlorophenols are discussed. Mechanisms of photolysis, reaction with hydroxyl radicals, singlet oxygen and secondary reactions for mono-, di-, tri-, tetra- and pentachlorophenol are proposed. The pathways for intermediate reactions e.g. dechlorination, oxidation, dimerization for chlorophenols are also presented.

  5. ADSORPTION OF NITRITE FROM AQUEOUS SOLUTION USING SAWDUST

    Directory of Open Access Journals (Sweden)

    Filiz Nuran ACAR

    2002-03-01

    Full Text Available The adsorption of nitrites ions onto sawdust materials have been studied using a batch system. In this study, using adsorbents are beech, pine, poplar and walnut sawdust materials. The maximum adsorption percentage was occured by beech sawdust. In the studies, the effects of adsorbents and the solution of initial pH for beech sawdust were analysed using the first order reversible reaction kinetic model. For the different experimental conditions, the reaction rate constants and equilibrium constant have been determined with this kinetic model.

  6. Removal of heavy metals from aqueous solution by Carrot residues

    International Nuclear Information System (INIS)

    The removal of Copper(II), Zinc(II), and Chromium (III) from wastewater by carrot residues was investigated to evaluate cation exchange capacity. The effects of solution P H and co-ions were studied in batch experiments. Adsorption equilibria were initially rapidly established, and then decreased markedly after 10 min. Column experiments were carried out in a glass column filled with carrot residues to evaluate the metal removal capacity. The influences of the feed concentration and feed rate were also studied in order to compare the dynamic capacity for metal binding in different feed concentrations

  7. The foam separation of zirconium (IV) from aqueous solutions

    International Nuclear Information System (INIS)

    The foam separation of zirconium(IV) from chloride solutions has been investigated over the 1.8-12 pH range using sodium lauryl sulphate or cetyl(trimethyl)ammonium bromide as collectors. The effects of gas flow rate, bubbling time, collector and zirconium(IV) concentrations, aging of the metal ion, and ionic strength have been studied and the results are discussed in relation to the hydrolytic behaviour of zirconium(IV). Under optimum conditions, ca. 99.5%-removal can be achieved. (orig.)

  8. Effects of pH on the stability of cyanidin and cyanidin 3-O-β-glucopyranoside in aqueous solution

    Directory of Open Access Journals (Sweden)

    Rakić Violeta P.

    2015-01-01

    Full Text Available The colour variation, colour intensity and stability at various pH values (2.0, 4.0, 7.0 and 9.0 of cyanidin 3-O-β-glucopyranoside (Cy3Glc and its aglycone cyanidin was investigated during a period of 8 hours storage at 25ºC. Our data showed that pH of aqueous solution had impact on spectroscopic profile of cyanidin and Cy3Glc. Beginning with the most acidic solutions, increasing the pH induce bathochromic shifts of absorbance maximum in the visible range for all examined pH values (with the exception pH 4.0 for cyanidin, while the presence of the 3-glucosidic substitution induce hypsochromic shift. Compared to cyanidin, Cy3Glc has higher colour intensity and higher stability in the whole pH range, except at pH 7.0. The 3-glucosidic substitution influences on the colour intensity of Cy3Glc in the alkaline region. After 8-hour incubation of Cy3Glc and cyanidin at pH 2.0 and 25 ºC, 99% of Cy3Glc and only 27% of cyanidin remained unchanged.

  9. Spray pyrolytic synthesis of large area NiO x thin films from aqueous nickel acetate solutions

    International Nuclear Information System (INIS)

    Non-stoichiometric nickel oxide thin films were prepared by pyrolytic decomposition of aerosol droplets of aqueous nickel acetate solution. Conventional un-nebulized spray pyrolysis system was used for the synthesis of thin films. The fine droplets were atomized by employing compressed air as carrier gas and allowed to decompose onto pre-heated Sn doped In2O3 (ITO) coated glass. The preparative parameters such as substrate temperature, solution concentration, distance from spray-nozzle to substrate, pressure of carrier air, etc., were optimized to obtain large area, uniform, thin films. The appropriate substrate temperature was selected after thermo-gravimetric analysis of nickel acetate. The temperature range of 330-420 deg. C was investigated for pyrolysis. Structural studies using X-ray diffraction (XRD) show the formation of cubic NiO. Morphological aspects of the films as-prepared and air annealed films have been studied by employing scanning electron microscopy. The optical absorption studies give direct band gap equal to 3.61 eV. The compositional analysis was carried out from the elemental depth profiles employing Auger electron spectroscopy. These indicate the formation of non-stoichiometric nickel oxide thin films. By studying I-V characteristics in alkaline electrolyte, electrocatalytic activity is tested

  10. Vapour pressure osmometry determination of water activity of binary and ternary aqueous (polymer + polymer) solutions

    International Nuclear Information System (INIS)

    Highlights: • VPO determination of water activity for binary and ternary aqueous polymer solutions. • Vapour pressure of binary and ternary aqueous polymer solutions were determined. • Water activities were correlated using the segment-based NRTL and Wilson models. • Molar Gibbs free energy changes due to mixing were determined. - Abstract: Precise water activity measurements at T = 308.15 K were carried out on several binary (water + polymer) and ternary {water + polymer (1) + polymer (2)} systems using the vapour pressure osmometry (VPO) technique. Polymers were polyethylene glycol 400 (PEG400), polyethylene glycol 6000 (PEG6000), polypropylene glycol 400 (PPG400), polyvinylpyrrolidone (PVP) and dextran (DEX). The water activity results obtained were used to calculate the vapour pressure of solutions as a function of concentration and the segment-based local composition models, NRTL and Wilson, were used to correlate the experimental water activity values. It was found that, for the polymer concentration range studied here, the values of the water activity obtained for the binary (water + polymer) solutions decrease in the order DEX > PVP > PEG6000 > PPG400 > PEG400. Furthermore, water activities of solutions of each polymer in the aqueous solutions of (5, 10, 15 and 20)% (w/w) other polymers investigated were also measured at T = 308.15 K. The ability of polymer (1) in decreasing the water activity of binary {water + polymer (2)} solutions was discussed on the basis of the (polymer + water) and {polymer (1) + polymer (2)} interactions

  11. Hydration and rotational diffusion of levoglucosan in aqueous solutions.

    Science.gov (United States)

    Corezzi, S; Sassi, P; Paolantoni, M; Comez, L; Morresi, A; Fioretto, D

    2014-05-14

    Extended frequency range depolarized light scattering measurements of water-levoglucosan solutions are reported at different concentrations and temperatures to assess the effect of the presence and distribution of hydroxyl groups on the dynamics of hydration water. The anhydro bridge, reducing from five to three the number of hydroxyl groups with respect to glucose, considerably affects the hydration properties of levoglucosan with respect to those of mono and disaccharides. In particular, we find that the average retardation of water dynamics is ≈3-4, that is lower than ≈5-6 previously found in glucose, fructose, trehalose, and sucrose. Conversely, the average number of retarded water molecules around levoglucosan is 24, almost double that found in water-glucose mixtures. These results suggest that the ability of sugar molecules to form H-bonds through hydroxyl groups with surrounding water, while producing a more effective retardation, it drastically reduces the spatial extent of the perturbation on the H-bond network. In addition, the analysis of the concentration dependence of the hydration number reveals the aptitude of levoglucosan to produce large aggregates in solution. The analysis of shear viscosity and rotational diffusion time suggests a very short lifetime for these aggregates, typically faster than ≈20 ps. PMID:24832286

  12. Hydration and rotational diffusion of levoglucosan in aqueous solutions

    Science.gov (United States)

    Corezzi, S.; Sassi, P.; Paolantoni, M.; Comez, L.; Morresi, A.; Fioretto, D.

    2014-05-01

    Extended frequency range depolarized light scattering measurements of water-levoglucosan solutions are reported at different concentrations and temperatures to assess the effect of the presence and distribution of hydroxyl groups on the dynamics of hydration water. The anhydro bridge, reducing from five to three the number of hydroxyl groups with respect to glucose, considerably affects the hydration properties of levoglucosan with respect to those of mono and disaccharides. In particular, we find that the average retardation of water dynamics is ≈3-4, that is lower than ≈5-6 previously found in glucose, fructose, trehalose, and sucrose. Conversely, the average number of retarded water molecules around levoglucosan is 24, almost double that found in water-glucose mixtures. These results suggest that the ability of sugar molecules to form H-bonds through hydroxyl groups with surrounding water, while producing a more effective retardation, it drastically reduces the spatial extent of the perturbation on the H-bond network. In addition, the analysis of the concentration dependence of the hydration number reveals the aptitude of levoglucosan to produce large aggregates in solution. The analysis of shear viscosity and rotational diffusion time suggests a very short lifetime for these aggregates, typically faster than ≈20 ps.

  13. The decisive role of free water in determining homogenous ice nucleation behavior of aqueous solutions.

    Science.gov (United States)

    Wang, Qiang; Zhao, Lishan; Li, Chenxi; Cao, Zexian

    2016-01-01

    It is a challenging issue to quantitatively characterize how the solute and pressure affect the homogeneous ice nucleation in a supercooled solution. By measuring the glass transition behavior of solutions, a universal feature of water-content dependence of glass transition temperature is recognized, which can be used to quantify hydration water in solutions. The amount of free water can then be determined for water-rich solutions, whose mass fraction, Xf, is found to serve as a universal relevant parameter for characterizing the homogeneous ice nucleation temperature, the meting temperature of primary ice, and even the water activity of solutions of electrolytes and smaller organic molecules. Moreover, the effects of hydrated solute and pressure on ice nucleation is comparable, and the pressure, when properly scaled, can be incorporated into the universal parameter Xf. These results help establish the decisive role of free water in determining ice nucleation and other relevant properties of aqueous solutions. PMID:27225427

  14. The decisive role of free water in determining homogenous ice nucleation behavior of aqueous solutions

    Science.gov (United States)

    Wang, Qiang; Zhao, Lishan; Li, Chenxi; Cao, Zexian

    2016-05-01

    It is a challenging issue to quantitatively characterize how the solute and pressure affect the homogeneous ice nucleation in a supercooled solution. By measuring the glass transition behavior of solutions, a universal feature of water-content dependence of glass transition temperature is recognized, which can be used to quantify hydration water in solutions. The amount of free water can then be determined for water-rich solutions, whose mass fraction, Xf, is found to serve as a universal relevant parameter for characterizing the homogeneous ice nucleation temperature, the meting temperature of primary ice, and even the water activity of solutions of electrolytes and smaller organic molecules. Moreover, the effects of hydrated solute and pressure on ice nucleation is comparable, and the pressure, when properly scaled, can be incorporated into the universal parameter Xf. These results help establish the decisive role of free water in determining ice nucleation and other relevant properties of aqueous solutions.

  15. Specific staining of nuclei with aqueous solutions of celestin blue B and gallocyanine.

    Science.gov (United States)

    Dutt, M K

    1982-09-01

    This paper presents methods for specific staining of nuclei with aqueous solutions of celestin blue B and gallocyanine in tissue sections from which RNA has been extracted selectively with concentrated phosphoric acid at 5 degrees C for 20 min or by hydrolysis in 6 N HCl at 28 degrees C for 15 min. It has been found that pH of the freshly prepared celestin blue B dye solution is 3.0 and that of an aqueous solution of gallocyanine is 2.8. These pHs can be lowered to 1.5 with concentrated sulphuric or nitric acid and at this pH staining of the nuclei is possible. But with concentrated sulphuric or nitric acid and at this pH staining of the nuclei is possible. But if the pHs are lowered with concentrated hydrochloric or phosphoric acid, effective use of these dyes is not possible. It has been suggested that some dispersion of the two dyes takes place with concentrated sulphuric or nitric acid which are used to lower the pH. Staining of the nuclei is also possible with an aqueous solution of celestin blue B at pH 3.0 but the same is not possible with gallocyanine at pH 2.8. The absorption spectra of nuclei stained with an aqueous solution of celestin blue B at pH 1.5 and 3.0 are fairly identical, the peak of maximum absorption being at 620 nm. Those of nuclei stained with an aqueous solution of gallocyanine reveal irregular peaks. Possible implications of these findings have been discussed. PMID:6183561

  16. Electrocrystallizations of copper on glassy carbon in CuCl2 silica sol and aqueous solutions

    Institute of Scientific and Technical Information of China (English)

    Yan Yan Feng; Min Gu; Yun Gui Du

    2012-01-01

    Electrocrystallizations of copper from both CuCl2 silica sol and aqueous solutions were studied by the chronoamperometry technique.It was found that current density contributions of the double-layer charging (iDL) in current-time transients (CTTs) from both of the solutions were large.An adsorption-nucleation based model was proposed to analyze quantitatively the CTTs,by which copper electrocrystallization mechanism was characterized as progressive nucleation with 3D growth (3DP) under diffusion control.The diffusion coefficient of copper ions and the AN∞ products in aqueous solutions were larger than that in silica sols,which indicated that copper nucleation was inhibited in sol solution.The large iDL may be resulted from the adsorption of chloride ions on the electrode surface.

  17. Complexation of Np(V) in aqueous solutions

    International Nuclear Information System (INIS)

    Various parameters affecting the diffusion coefficient of neptunium (V) in clay systems have been studied; e.g. clay mineralogy, the charge compensating cation in the clay, the ionic strength of a background perchlorate solution and the presence of three organic ligands. Several well established techniques have been employed to obtain stability constants for the neptunium systems; Np(V) EDTA and Np(V)/citrate, Np(V)/Aldrich Humic Acid (AHA), Np(V)/Gorleben Hulic Acid (GHA) and for the uranium systems U(VI)/EDTA, U(VI)/citrate and U(VI)/AHA. The experimental techniques employed were UV/visible spectroscopy, polarography, solvent extraction and ion exchange. (author). 50 refs., 24 figs., 9 tabs

  18. Complexation of Np(V) in aqueous solutions

    International Nuclear Information System (INIS)

    Various parameters affecting the diffusion coefficient of neptunium (V) in clay systems have been studied; e.g. clay mineralogy, the charge compensating cation in the clay, the ionic strength of a background perchlorate solution and the presence of three organic ligands. Several well established techniques have been employed to obtain stability constants for the neptunium systems; Np(V)/EDTA and Np(V)/citrate, Np(V)/Aldrich Humic Acid (AHA), Np(V)/Gorleben Humic Acid (GHA) and for the uranium systems U(VI)/EDTA, U(VI)/citrate and U(VI)/AHA. The experimental techniques employed were UV/visible spectroscopy, polarography, solvent extraction and ion exchange. (Author)

  19. persimmon tannin-formaldehyde gel decontamination of dilute aqueous solutions

    International Nuclear Information System (INIS)

    in the present work, the extracted juice of unripe astringent persimmon fruit, designated as (kakishibu) was found to have an extremely high affinity for uranium ion. to develop efficient adsorbent for uranium ion the juice was immobilized in formaldehyde. the removal of uranium ion onto the formed gel was found to be affected by several factors such as, concentration of formaldehyde in gel, equilibration time, solution ph, concentration of uranium ion, mass of adsorbent, presence of some cations and anions . the sorption isotherm was discussed in the light of Freundlich and Langmuir models. from Freundlich equation, the exponent 1/n was found in the range of 1>1/n0, δS0 and δG0 were calculated . the capacity of adsorbent was also determined by column technique and found to 20.20 mg/g

  20. Photodegradation of α-naphthaleneacetic acid in aqueous solution

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Kinetic processes of α-naphthaleneacetic acid (NAA) photolysis were studied under different conditions. The results showed that the ultraviolet light was more effective than fluorescent light in promoting degradation, and the degradation of NAA under ultraviolet light followed the first order kinetics with the photolysis rate constant of 1.15 x 10-2 min-1 and half-life time (t1/2) of 60 min. Further, it was proved that the photolysis rate was higher in the presence of oxygen, titanium dioxide (TiO2), and low pH ( acidic solution). At last, two photolysis intermediates were identified by GC-MS and possible photolysis pathways were proposed.

  1. Removal of Uranium From Aqueous Solution by Carbon Nanotubes.

    Science.gov (United States)

    Yu, Jing; Wang, Jianlong

    2016-10-01

    The adsorption of uranium onto carbon nanotubes (CNTs) was investigated. The effect of solution pH, contact time, initial uranium concentration, and temperature on the adsorption capacity of uranium was determined. CNTs were characterized by using scanning electron microscopy (SEM), transmission electron microscopy (TEM), powder x-ray diffraction (XRD), Raman spectra, and the Fourier infrared spectra (FTIR). The diameters of the CNTs varied from 10 to 50 nm in diameter and 1 ~ 2 μm in length. FTIR spectra analysis indicated that carboxyl groups were involved in adsorption of U(VI) by CNTs. The experimental results showed that U(VI) adsorption onto CNTs reached equilibrium within 10 min, and the removal efficiency was 95% at pH = 5. The adsorption kinetics of U(VI) could be described by a pseudo first-order kinetic model. The adsorption isotherm conformed to the Slips model. The adsorption process was spontaneous and endothermic. PMID:27575349

  2. Probing Ionic Liquid Aqueous Solutions Using Temperature of Maximum Density Isotope Effects

    Directory of Open Access Journals (Sweden)

    Mohammad Tariq

    2013-03-01

    Full Text Available This work is a new development of an extensive research program that is investigating for the first time shifts in the temperature of maximum density (TMD of aqueous solutions caused by ionic liquid solutes. In the present case we have compared the shifts caused by three ionic liquid solutes with a common cation—1-ethyl-3-methylimidazolium coupled with acetate, ethylsulfate and tetracyanoborate anions—in normal and deuterated water solutions. The observed differences are discussed in terms of the nature of the corresponding anion-water interactions.

  3. A Concise Equation of State for Aqueous Solutions of Electrolytes Incorporating Thermodynamic Laws and Entropy

    Directory of Open Access Journals (Sweden)

    Raji Heyrovská

    2004-03-01

    Full Text Available Abstract: Recently, the author suggested a simple and composite equation of state by incorporating fundamental thermodynamic properties like heat capacities into her earlier concise equation of state for gases based on free volume and molecular association / dissociation. This work brings new results for aqueous solutions, based on the analogy of the equation of state for gases and solutions over wide ranges of pressures (for gases and concentrations (for solutions. The definitions of entropy and heat energy through the equation of state for gases, also holds for solutions.

  4. Effects of applied potential on the stress corrosion cracking behavior of 7003 aluminum alloy in acid and alkaline chloride solutions

    Science.gov (United States)

    Zhang, Xiao-yan; Song, Ren-guo; Sun, Bin; Lu, Hai; Wang, Chao

    2016-07-01

    Potentiodynamic polarization tests and slow strain rate test (SSRT) in combination with fracture morphology observations were conducted to investigate the stress corrosion cracking (SCC) behavior of 7003 aluminum alloy (AA7003) in acid and alkaline chloride solutions under various applied potentials ( E a). The results show that AA7003 is to a certain extent susceptible to SCC via anodic dissolution (AD) at open-circuit potential (OCP) and is highly susceptible to hydrogen embrittlement (HE) at high negative E a in the solutions with pH levels of 4 and 11. The susceptibility increases with negative shift in the potential when E a is less than -1000 mV vs. SCE. However, the susceptibility distinctly decreases because of the inhibition of AD when E a is equal to -1000 mV vs. SCE. In addition, the SCC susceptibility of AA7003 in the acid chloride solution is higher than that in the alkaline solution at each potential. Moreover, the effect of hydrogen on SCC increases with increasing hydrogen ion concentration.

  5. AFM study of steel corrosion in aqueous solutions in concrete

    Directory of Open Access Journals (Sweden)

    Díaz-Benito, B.

    2011-03-01

    Full Text Available Early corrosion stages are studied in carbon steel by means of a solution simulating that contained in concrete pores. Non-carbonated solution contains 5% NaCl. The atomic force microscopy (AFM technique is used to study material performance after different immersion times (up to 48 h. Obtained data are compared to electrochemical ones (corrosion potential and polarization resistance. Analysis of images and roughness evolution along time shows that steel initially tends to reach passivity, although the passive layer rapidly loses its protective character due to chloride attack.

    Este trabajo estudia los primeros estados de la corrosión de un acero al carbono en una disolución que simula la existente en los poros del hormigón, sin carbonatar, con un 5% de NaCl. Para ello, se ha empleado la técnica de microscopía de fuerza atómica (AFM, estudiando el comportamiento del material tras diferentes tiempos de inmersión, hasta 48 h, en la disolución. Estos datos se comparan con datos electroquímicos (potencial de corrosión y resistencia de polarización. El análisis de las imágenes y la evolución de la rugosidad con el tiempo muestran que el acero tiende inicialmente a pasivarse, pero la capa pasiva pierde rápidamente su carácter protector debido al ataque de los cloruros.

  6. Degradation/oxidation susceptibility of organic photovoltaic cells in aqueous solutions.

    Science.gov (United States)

    Habib, K; Husain, A; Al-Hazza, A

    2015-12-01

    A criterion of the degradation/oxidation susceptibility of organic photovoltaic (OPV) cells in aqueous solutions was proposed for the first time. The criterion was derived based on calculating the limit of the ratio value of the polarization resistance of an OPV cell in aqueous solution (Rp(s)) to the polarization resistance of the OPV cell in air (Rp(air)). In other words, the criterion lim(Rp(s)/Rp(air)) = 1 was applied to determine the degradation/oxidation of the OPV cell in the aqueous solution when Rp(air) became equal (increased) to Rp(s) as a function of time of the exposure of the OPV cell to the aqueous solution. This criterion was not only used to determine the degradation/oxidation of different OPV cells in a simulated operational environment but also it was used to determine the electrochemical behavior of OPV cells in deionized water and a polluted water with fine particles of sand. The values of Rp(s) were determined by the electrochemical impedance spectroscopy at low frequency. In addition, the criterion can be applied under diverse test conditions with a predetermined period of OPV operations.

  7. CYCLIC VOLTAMMETRY OF ORGANIC AND INORGANIC N-CHLORAMINES IN AQUEOUS SOLUTION

    Science.gov (United States)

    Aqueous solutions or organic and inorganic N-chloramines as well as hypochlorite were examined by cyclic voltammetry at DH 8 and in strong acid (pH<2) with platinum and glassy carbon electrodes. The inorganic N-chloramines were characterized in 1 M HC104. NHC12 is reduced at abou...

  8. Spectroelectrochemical and cyclic voltamperometry of trigonal cluster of ruthenium acetate with pirazine in aqueous solution

    International Nuclear Information System (INIS)

    The electrochemical and spectroelectrochemical behavior of the trinuclear μ - oxo - cluster [Ru3O (Ac)6 (pirazine)3] in aqueous solution is reported. The reductive potential of the clusters and energy from transfer of charge metal-ligand are analysed. (M.J.C.)

  9. Adsorption of ammonium dinitramide (ADN) from aqueous solutions. 1. Adsorption on powdered activated charcoal.

    Science.gov (United States)

    Santhosh, G; Venkatachalam, S; Ninan, K N; Sadhana, R; Alwan, S; Abarna, V; Joseph, M A

    2003-03-17

    Investigations on the adsorption of ammonium dinitramide (NH(4)N(NO(2))(2)) (ADN) from aqueous solutions on powdered activated charcoal (PAC) were carried out in order to find out an effective and easier method of separating ADN from aqueous solutions. The effectiveness of PAC in the selective adsorption of ADN from aqueous solutions of ADN (ADN-F) and ADN in presence of sulfate (SO(4)(2-)) and nitrate (NO(3)(-)) ions (ADN-PS) was examined and compared using batch and column methods. The adsorption process follows both Langmuir and Freundlich adsorption isotherms and the isotherm parameters for the models were determined. The observed data favor the formation of monolayer adsorption. The adsorption capacities were found to be 63.3, 119, 105.3 and 82 mg of ADN per g of PAC for ADN-F (batch), ADN-PS (batch), ADN-F (column) and ADN-PS (column), respectively. Break-through curves for ADN-F and ADN-PS were obtained for the optimization of separation of ADN from aqueous solutions. Elution curves were generated for the desorption of ADN from PAC using hot water as eluent.

  10. Mixed matrix membranes for efficient adsorption of copper ions from aqueous solutions

    NARCIS (Netherlands)

    Tetala, Kishore K.R.; Stamatialis, Dimitrios F.

    2013-01-01

    This work presents adsorption of copper (Cu2+) ions from aqueous solutions using mixed matrix membrane (MMM) and its elution afterwards. The developed flat sheet MMM, comprises of chitosan beads incorporated in Ethylene vinyl alcohol (EVAL) polymer porous matrix and exhibits static Cu2+ ion adsorpti

  11. Speciation of actinides in aqueous solution by time-resolved laser-induced fluorescence spectroscopy (TRLFS)

    International Nuclear Information System (INIS)

    Time-resolved laser-induced fluorescence spectroscopy (TRLFS) as a sensitive and selective method has been applied to the speciation of actinides in aqueous solution. Studies on hydrolysis and carbonate complexation of U(VI) and on determination of hydration number of Cm(III) are reported. (author)

  12. Reentrant condensation of lysozyme: Implications for studying dynamics of lysozyme in aqueous solutions of lithium chloride

    Energy Technology Data Exchange (ETDEWEB)

    Mamontov, Eugene [ORNL; O' Neill, Hugh Michael [ORNL

    2014-01-01

    Recent studies have outlined the use of eutectic solution of lithium chloride in water to study microscopic dynamics of lysozyme in an aqueous solvent that is remarkably similar to pure water in many respects, yet allows experiments over a wide temperature range without the solvent crystallization. The eutectic point in (H2O)R(LiCl) system corresponds to R 7.3, and it is of interest to investigate whether less concentrated aqueous solutions of LiCl could be employed in low-temperature studies of a solvated protein. We have investigated a range of concentrations of lysozyme and LiCl in aqueous solutions to identify systems that do not show phase separation and avoid solvent crystallization on cooling down. Compared to the lysozyme concentration in solution, the concentration of LiCl in the aqueous solvent plays the major role in determining systems suitable for low-temperature studies. We have observed interesting and rich phase behavior reminiscent of reentrant condensation of proteins.

  13. Change in the amino acid composition of calf skin collagen after. gamma. -irradiation in aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Duzhenkova, N.A.; Savich, A.V. (Institut Biofiziki, Moscow (USSR))

    A study was made of the amino acid composition of calf skin collagen after ..gamma..-irradiation (/sup 60/Co) of 2.5x10/sup -6/ M aerated aqueous protein solution within the dose range from 30 to 2000 Gy. The radiosensitivity of amino acid residues was compared.

  14. Chemiluminescence in the reaction of ozone with 6-methyluracil in aqueous solutions

    Science.gov (United States)

    Zimin, Yu. S.; Khairullina, L. R.; Kutlugil'dina, G. G.; Mustafin, A. G.

    2015-12-01

    Chemiluminescence in the visible part of the spectrum during the oxidation of 6-methyluracil with ozone in aqueous solutions was found. The kinetics of variation of the luminescence intensity was studied in the temperature range 287-333 K, and the activation parameters of the process were determined.

  15. Relaxation of the Silver/Silver Iodide Electrode in Aqueous Solution

    NARCIS (Netherlands)

    Peverelli, K.J.

    1979-01-01

    The aim of this study is to detect and characterize relaxation processes on silver/silver iodide electrodes in aqueous electrolyte solution. The information obtained is to be used for an estimation of the consequences of similar processes on colloidal AgI particles during encounter.In chapter 1 a ge

  16. Diffusion Coefficient and Solubility of Isobutene and trans-2-Butene in Aqueous Sulfuric Acid Solutions

    NARCIS (Netherlands)

    Brilman, Derk W.F.; Swaaij, Wim P.M. van; Versteeg, Geert F.

    2001-01-01

    The diffusion coefficient and the physical solubility of isobutene and trans-2-butene in aqueous sulfuric acid solutions cannot be determined experimentally due to the occurrence of fast chemical reactions. In the present contribution these physicochemical parameters are estimated. For the solubilit

  17. Femtosecond midinfrared study of aggregation behavior in aqueous solutions of amphiphilic molecules

    NARCIS (Netherlands)

    Petersen, Christian; Bakulin, Artem A.; Pavelyev, Vlad G.; Pshenichnikov, Maxim S.; Bakker, Huib J.

    2010-01-01

    We study the spectral and orientational dynamics of HDO molecules in aqueous solutions of different concentrations of tertiary butyl alcohol (TBA) and trimethylamine-N-oxide (TMAO). The spectral dynamics is investigated with femtosecond two-dimensional infrared spectroscopy of the O-H stretch vibrat

  18. Blueshift of the silver plasmon band using controlled nanoparticle dissolution in aqueous solution

    DEFF Research Database (Denmark)

    Mogensen, Klaus Bo; Kneipp, Katrin

    2014-01-01

    In this work, we report the size-dependent blue shift of the silver nanoparticle plasmon band in aqueous solution by means of UV/VIS spectroscopy. An oxidative dissolution scheme allows a gradual decrease in the particle sizes by controlled oxidation during recording of the optical spectra. Hence...

  19. Deacidification of oils and fats of biological origine by aqueous solutions of tertiary amines*

    Directory of Open Access Journals (Sweden)

    Peter Siegfried

    2001-01-01

    Full Text Available Deacidification of triacylglycerols by extraction is investigated using aqueous solutions of amines as extractants. Tertiary amines with boiling points ranging between 100° and 170°C, such as 2-methylamino-diethanol, 2-dimethylamino-ethanol, 4-methylmorpholine, 1-dimethylamino-2-propanol etc. were found to be suitable substances. Especially the deacidification by aqueous solutions of 2-dimethylamino-ethanol (DMAE was amply investigated as it is used as an active agent in remedies. Amazingly gelatinous soap stocks are not formed, when the concentration of DMAE exceeds 20% if the free fatty acid content of the oil is below 15%. Two liquid phases are formed in systems composed of triacylglyceroles and aqueous solutions containing 20 to 80% DMAE. Palm oil containing 4.3 wt.% free fatty acids was mixed with an equal amount of an aqueous solution of 30 wt.% DMAE at 60°C. In equilibrium an extract containing 86 wt.% free fatty acids (solvents deducted and a raffinate of 0.09 wt.% free fatty acids are obtained. Loss of neutral oil being 0.7 wt.%.

  20. GROUP CONTRIBUTIONS TO COSPHERE COSPHERE INTERACTION PARAMETERS - ESTER HYDROLYSIS IN AQUEOUS-SOLUTIONS CONTAINING CARBOXAMIDES

    NARCIS (Netherlands)

    ENGBERTS, JBFN; KERSTHOLT, R; BLANDAMER, MJ

    1991-01-01

    Rate constants for the hydrolysis of p-methoxyphenyl dichloroethanoate in dilute aqueous solutions of carboxamides can be quantitatively accounted for using cosphere interaction parameters G(c) which are linear functions of the number of methylene groups in an added carboxamide.