WorldWideScience

Sample records for applications preparacao caracterizacao

  1. Preparation, characterization and evaluation of electrocatalysts supported on functionalized carbon black for polymer exchange membrane fuel cell applications; Preparacao, caracterizacao e avaliacao de eletrocatalisadores suportados em carbono funcionalizado para aplicacao em celulas a combustivel tipo PEM

    Energy Technology Data Exchange (ETDEWEB)

    Carmo, Marcelo do

    2008-12-18

    The fuel cell technology associated with the growing exigency of low environmental impact energy became prosperous in the world energy scenery. The fuel cell is basically a device that converts directly the chemical energy of a fuel into electrical and thermal energy with a continuous operation by the constant feed of a fuel. Especially, the carbon black Vulcan XC72 is usually employed as an electro catalyst support, and some factors as an accessible and high surface area in order to get maximum particles dispersion, pore size, adequate pore distribution and the presence of functional groups in the carbon black surface are considered fundamental characteristics for an innovative materials development. However, the Vulcan XC72 still reveals insufficient conditions for these purposes. This study consists in the preparation and in the physical chemical characterization of functionalized carbon black by hydrogen peroxide and by polymeric chains with proton conduction properties, and its posterior utilization as electro catalyst support for PEMFC and DMFC application. After the carbon functionalization, an improvement in the carbon black dispersion in water media was observed, a beneficial effect for electro catalyst preparation. It was also observed, that the functional groups and the polymeric chains worked as stabilizers in the particle growing, producing much more homogeneous electrocatalysts, exhibiting smaller average particle size. Especially, in the case of polymeric chains functionalization, a decrease in the ohmic drop was observed for this system, attributed to an improvement in the proton transference. (author)

  2. Preparation and characterization of zirconium based colloidal suspensions; Preparacao e caracterizacao de suspensoes coloidais a base de zirconio

    Energy Technology Data Exchange (ETDEWEB)

    Chiavacci, Leila Aparecida; Pulcinelli, Sandra Helena; Santilli, Celso Valentim [UNESP, Araraquara, SP (Brazil). Inst. de Quimica

    1995-12-31

    Attention has been paid to zirconia based ceramic materials due to its technological applications, like catalysts, ionic changers, sensors, etc. Colloidal suspensions based on zirconium, containing different cation/anion molar ratio, have been prepared aiming the improvement of its extrinsical properties. The systems have been characterized by turbidimetry and the xerogels have been analysed by scanning electronic microscopy, infrared spectroscopy and x-ray diffraction. Results make evident the viability of preparation of transparent colloidal suspensions, gel and powders, in which the particles size and morphology could be controlled. (author) 3 figs.

  3. Preparation and characterization of PVA/SSA membranes with Al{sub 2}O{sub 3} nanoparticles for fuel cell applications; Preparacao de caracterizacao de membranas de PVAL/SSA na presenca de nanoparticulas de Al{sub 2}O{sub 3} para aplicacao em celulas de combustivel

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Paula N.; Pires, Alfredo T.N. [Grupo de Estudo em Materiais Polimericos - POLIMAT - UFSC, Florianopolis, SC (Brazil); Catarino, Margarida; Brandao, Lucia; Tanaka, Alfredo; Mendes, Adelio [Faculdade de Engenharia da Universidade do Porto, Porto (Portugal)

    2011-07-01

    In the present study, PVA/SSA membranes were prepared with and without the addition of Al{sub 2}O{sub 3} nanoparticles. Sulfosuccinic acid (SSA) was used as the crosslinking agent. Membranes were prepared with different amounts of SSA (26, 43 and 55 wt.%) and with 5 and 10 wt.% of nanoparticles. Crosslinking was performed at 90 degree C during 1.5 h. Membranes were analyzed by infrared spectroscopy, thermal analysis, water absorption, ion exchange capacity (IEC) and proton conductivity. The results showed that control of the crosslinking conditions, IEC value, water absorption and polymer structure are of significant importance to obtain a set of properties suitable for application in proton exchange membrane fuel cells. (author)

  4. Preparation and characterization of polymer blends based on recycled PET and polyester derived by terephthalic acid; Preparacao e caracterizacao de blendas polimericas a base de PET reciclado e poliester derivado do acido tereftalico

    Energy Technology Data Exchange (ETDEWEB)

    Ohara, L.; Miranda, C.S.; Fiuza, R.P.; Luporini, S.; Carvalho, R.F.; Jose, N.M., E-mail: leandro.ohara@gmail.co [Universidade Federal da Bahia (GECIM/UFBA), Salvador, BA (Brazil). Inst. de Quimica. Grupo de Energia e Ciencias dos Materiais

    2010-07-01

    Environmentally friendly materials, made from industrial waste, are being increasingly used as a solution to the growing amount of waste generated by society, but also as a cheaper alternative to replace conventional materials for use in construction. In this work were investigated the properties of polymer blends based on recycled PET and a polyester derived from terephthalic acid and glycerin, a co-product of biodiesel. The samples were characterized by XRD, TGA, DSC, FTIR and SEM. The polyester synthesized showed a degradation event near 300 deg C. The blends with higher ratio of PET showed thermal behavior similar to pure PET. The X-ray diffraction showed that the polymer blends are semicrystalline materials. The micrographs presents the presence of a smooth surface, indicating the possibility of miscibility between the arrays. Therefore, the blending makes possible the fabrication of low-cost materials with applications in several areas. (author)

  5. Preparation and characterization of sugar cane bagasse fiber modified with nanoparticles of zirconium oxide; Preparacao e caracterizacao de fibras de bagaco de cana modificadas com nanoparticulas de oxido de zirconio

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, K.C.C. de; Mulinari, D.R.; Voorwald, H.C.J.; Cioffi, M.O.H., E-mail: kcccarvalho@hotmail.com.b [UNESP, Guaratingueta, SP (Brazil). Fac. de Engenharia. Dept. de Materiais e Tecnologia(FEG)

    2010-07-01

    The sugar cane bagasse fiber are renewable materials and have great application potential when used as reinforcement in a polymer matrix to give rise to composite materials and as supports for adsorption of heavy metals. This paper therefore describes the preparation and characterization of bleached and hydrated zirconium oxide modified sugar cane bagasse fiber by conventional precipitation method. Through the technique of electron microscopy we observed the presence of oxide nanoparticles on the fiber surface, proving the efficiency of the conventional precipitation method. With the X-ray diffraction analysis it was determined a decrease of 6.2% in the crystallinity index of modified fibers when compared to the bleached fibers showing the deposition of amorphous zirconium oxide on the fiber surface. (author)

  6. New routes of preparation of polyaniline films and dosimetric characterization for high-doses gamma radiation; Novas rotas de preparacao de filmes de polianilina e caracterizacao dosimetrica para radiacao gama em altas doses

    Energy Technology Data Exchange (ETDEWEB)

    Pacheco, Ana Paula Lima

    2003-08-15

    This work presents a new conducting polymeric material based on polyaniline thin films that will be used in the confection of dosimetric devices. On preparation of the films a homogeneous and viscous solution of poly (acrylic acid) and MnO{sub 2} is deposited on PMMA surface, which after dried, is immersed in an acid aniline solution. The films formed present low resistivity (6.10{sup 2} {omega}m), good mechanical resistance and adherence on the electrodes. The films were characterized by infrared spectroscopy, conductivity measurements and manganese elemental analyses. The resistance variations show linear correlation (r{sup 2} = 0,9928) with gamma irradiation dose in the range of 1000 to 6000 Gy, with medium error less than 5% and sensitivity response. The dosimetric devices present as advantage real time measurements, low cost, use in calibration of industrial radioactive sources. Moreover, this composite could in future replace Fricke dosimeter and its applications. A calibration curve is showed for PANI dosimeter, here proposed, to use at high gamma doses. (author)

  7. Production and characterization of ceramics for armor application; Producao e caracterizacao de ceramicas para blindagem balistica

    Energy Technology Data Exchange (ETDEWEB)

    Alves, J.T.; Lopes, C.M.A. [Instituto Tecnologico de Aeronautica (ITA), Sao Jose dos Campos, SP (Brazil). Div. de Engenharia Mecanica-Aeronautica; Assis, J.M.K.; Melo, F.C.L., E-mail: cmoniz@iae.cta.b [Instituto de Aeronautica e Espaco (IAE), Sao Jose dos Campos, SP (Brazil). Div. de Materiais

    2010-07-01

    The fabrication of devices for ballistic protection as bullet proof vests and helmets and armored vehicles has been evolving over the past years along with the materials and models used for this specific application. The requirements for high efficient light-weight ballistic protection systems which not interfere in the user comfort and mobility has driven the research in this area. In this work we will present the results of characterization of two ceramics based on alumina and silicon carbide. The ceramics were produced in lab scale and the specific mass, scanning electron microscopy (SEM) microstructure, Vickers hardness, flexural resistance at room temperature and X-ray diffraction were evaluated. Ballistic tests performed in the selected materials showed that the ceramics present armor efficiency. (author)

  8. Preparation and characterization of sulfated zirconia acid catalysts for application in the esterification of cottonseed oil; Preparacao e caracterizacao de catalisadores acidos de zirconia sulfatada para aplicacao na esterificacao do oleo de algodao

    Energy Technology Data Exchange (ETDEWEB)

    Silva, F. N.; Moura, T. F. B.; Silva, A.S.; Costa, A.C.F.M., E-mail: fnilson.s@hotmail.com [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Pos-graduacao em Engenharia de Materiais; Pallone, E.M.J.A. [Universidade de Sao Paulo (USP), Pirassununga, SP (Brazil). Dept. de Ciencias Basicas

    2017-07-15

    This work aimed to produce zirconia by combustion synthesis, to analyze the structure and morphology comparatively with a commercial monoclinic ZrO{sub 2} , as well as, to investigate the sulfation, aiming to obtain acid catalysts for its use in the esterification of cotton oil for biodiesel. The samples were characterized by X-ray diffraction, scanning electron microscopy (SEM), specific surface area by BET method, infrared spectroscopy (FTIR), thermal analysis (TG/DrTG/DTA), granulometric distribution, pH and chromatography. The synthesized sample evidenced the formation of the monoclinic phase with traces of the orthorhombic phase, while in the commercial sample only the monoclinic phase was observed. In the sulfation process, traces of the tetragonal phase, typical of sulfated zirconia, were observed with the presence of the monoclinic phase in the two samples. With the impregnation of the sulfate ion on the surface of the samples, an increase in the particle size was observed, as seen in the characterization of BET, granulometric distribution and SEM, which also indicated a homogeneous morphology consisting of fine particles of approximately spherical shape for both samples. The chromatography indicated conversion of 65.5 and 91.8% in methyl esters to the synthesized and commercial SO{sub 4} {sup 2-}/ZrO{sub 2} , respectively. The results indicated that the sulfation increased the acidity, which was evidenced by the decrease in the pH, ranging from 5.12 to 2.65, which contributed significantly to the increase of the conversion, indicating that the SO{sub 4} {sup 2-}/ZrO{sub 2} is a promising catalyst in the esterification. (author)

  9. Preparation and characterization of phase-pure anatase and rutile TiO{sub 2} powder by new chemistry route; Preparacao e caracterizacao de nanoparticulas de TiO{sub 2} nas fases anatase e rutila por uma nova rota quimica

    Energy Technology Data Exchange (ETDEWEB)

    Pereira, E. A.; Montanhera, M.A.; Paula, F.R., E-mail: sevlarede2@yahoo.com.br [Universidade Estadual Paulista Julio de Mesquista Filho (UNESP), Ilha Soltiera, SP (Brazil). Faculdade de Engenharia. Departameinto de Fisica e Quimica; Spada, E.R. [Universidade de Sao Paulo (USP), Sao Carlos, SP (Brazil). Institutlo de Fisica

    2014-07-01

    Titanium dioxide (TiO{sub 2}) is used in a wire range applications such as photocatalysis and sensor device. In this work is shown a new and effective method for the preparation of TiO{sub 2} nanocrystalline in the crystallographic forms, anatase and rutile. The method involves dissolving the TiOSO{sub 4} powder in H{sub 2}O{sub 2} solution and thermal treatment of amorphous precipitate. The technique of X-ray diffraction was used to follow the structure evolution of amorphous precipitate. Pure anatase structure and rutile are obtained at 600 deg C and 1000 deg C with a grain size estimated 24 and 55 nm respectively. TiO{sub 2} nanoparticles is a promising alternative of the low cost whose potential for solar cells deserve a careful evaluation, especially in hybrid solar cells that employs TiO{sub 2} as electron acceptor and as transport channels. (author)

  10. Preparation and characterization of composites based on PBAT/Starch blend, micro and nanofillers of bio-CaCO{sub 3}; Preparacao e caracterizacao de compositos baseados na blenda de PBAT/amido, micro e nanocargas de bio-CaCo{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Valquiria A.; Neto, Jose C. de M.; Moura, Esperidiana A.B. [Instituto de Pesquisas Energeticas e Nucleares (IPEN-CNEN/SP), Sao Paulo, SP (Brazil); Tiimob, Boniface; Rangari, Vijaya K. [Department of Materials Science and Engineering, Tuskegee University, Tuskegee, AL (United States); Silva, Raimundo N.A. da, E-mail: jmacedo@uea.edu.br [Universidade do Estado do Amazonas (UEA), Manaus, AM (Brazil). Escola Superior de Tecnologia. Coordenacao de Engenharia de Materiais

    2015-07-01

    Biodegradable polymeric materials have been used as an alternative to synthetic polymeric materials due to their reduced environmental impact. Among the biodegradable polymers is investigated poly (butylene adipate-co-terephthalate) (PBAT). This polymer has the flexibility, high strain at break and easy processing, but a high cost and low toughness that limits their applications. The development of PBAT blends with thermoplastic starch or other biodegradable polymers may lead to a balance of properties, expand its range of applications and also make it more economically viable. The mechanical properties of biodegradable PBAT blends may be further improved by incorporating micro or nanofillers from renewable sources. This study aimed to the processing and characterization of a PBAT/Starch blend reinforced with 2% (wt.) of bioCaCO{sub 3} nanoparticles (nano-bioCaCO{sub 3}) and 5% (wt.) of bioCaCO{sub 3}-micro (particles ≤ 125 μm). For the preparations were used a co-rotating twin-screw extruder. For the characterization of the prepared materials were used X-ray diffraction (XRD) and tensile test. The XRD results showed the greatest intensity peak of CaCO{sub 3} in the matrix for composites containing bio-CaCO{sub 3} nanofillers suggesting a better interaction between matrix and nanofillers. The results of the tensile test confirmed the better interaction between matrix and nanofillers. These results showed that the addition of only 2 % (wt.) of bio-CaCO{sub 3} nanoparticles in PBAT/Starch blend led to obtaining a tougher material with improved tensile strength and elastic modulus properties regarding the polymer blend. (author)

  11. Preparation and characterization of bentonite organo clay; Preparacao de caracterizacao de argilas bentonitas organofilicas

    Energy Technology Data Exchange (ETDEWEB)

    Bertagnolli, C.; Almeida Neto, A.F. [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Fac. de Engenharia Quimica. Lab. de Engenharia Ambiental; Silva, M.G.C., E-mail: meuris@feq.unicamp.b [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Fac. de Engenharia Quimica

    2009-07-01

    Bentonite clays organically modified have great potential use for environmental remediation, especially in the separation of organic compounds from the water. The aim of this work was the preparation of organophilic clays from 'Verde-Lodo' bentonite clay with the quaternary ammonium salts cetyl-pyridinium chloride and benzalkonium chloride. The materials obtained were characterized by XRD, thermogravimetric analyses, Helium picnometry, SEM and energy dispersive X-ray techniques. The results show consistently successful synthesis of the organoclay through the increase in the basal spacing, as well as salt elimination picks and presence of carbon and chlorine in the modified clays; they are inexistent elements in the natural clay. (author)

  12. Preparation and characterization of the fish reference material; Preparacao e caracterizacao de um material de referencia de peixe

    Energy Technology Data Exchange (ETDEWEB)

    Ulrich, Joao Cristiano

    2011-07-01

    The certified reference materials (CRMs) play an important role in obtaining measurement results traceable to the International System of Units, through an unbroken chain of comparisons. Thus, the demand for new certified reference materials (CRMs) increases every day in all areas of knowledge. The availability of reference materials, mainly in Brazil is still incipient, given that the demand far exceeds the available variety of these materials. The amount of certified reference materials available in the country is insufficient to meet the need of the scientific community and demands for development of new methodologies. Among the many areas in need of reference materials, we highlight the importance for the food trade balance for these products within the country. The certification of food products, intended both for export and for domestic consumption, requires analysis methods that provide precise and accurate results to ensure product quality. This paper describes the preparation and certification of a reference material in the fish matrix in mercury and methylmercury. The study brings together since the stage of material selection, preparation, development of homogeneity and stability studies and characterization. The certification was performed by means of measurements using two analytical techniques, flow injection analysis - cold vapor atomic absorption spectrometry (FIA-CV-AAS) and isotope dilution applied to mass spectrometry (IDMS), which is a primary method. In this work the standards of the ISO 30 (ABNT 30-34) and ISO Guide 35 was used as the basis for the preparation and characterization of the material. For the calculation of uncertainties was used the GUM and Eurachem guide. As a result, was produced and certified a lot of material in relation to the concentration of mercury (Hg = 0.271 {+-} 0.057 mg g{sup -1}) and methylmercury (MeHg = 0.245 {+-} 0.038 mg g{sup -1}), and informational values of lead and arsenic. (author)

  13. Thermoplastic starch materials prepared from rice starch; Preparacao e caracterizacao de materiais termoplasticos preparados a partir de amido de arroz

    Energy Technology Data Exchange (ETDEWEB)

    Pontes, Barbara R.B.; Curvelo, Antonio A.S., E-mail: barbarapont@gmail.co [Universidade de Sao Paulo (IQSC/USP), Sao Carlos, SP (Brazil). Inst. de Quimica

    2009-07-01

    Rice starch is a source still little studied for the preparation of thermoplastic materials. However, its characteristics, such as the presence of proteins, fats and fibers may turn into thermoplastics with a better performance. The present study intends the evaluation of the viability of making starch thermoplastic from rice starch and glycerol as plasticizer. The results of X-ray diffraction and scanning electronic microscopy demonstrate the thermoplastic acquisition. The increase of plasticizer content brings on more hydrophilic thermoplastics with less resistance to tension and elongation at break. (author)

  14. Preparation, characterization and certification of uranium isotope reference materials; Preparacao, Caracterizacao e certificacao de materiais de referencia isotopicos de uranio

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira Junior, Olivio Pereira de

    2006-07-01

    This work describes the preparation, characterization and certification of a set of uranium isotope reference materials ranging from 0.5 to 20.0 % of {sup 235}U in mass. The most important concepts of metrology in chemical measurements were applied so that the certified quantities in these materials could be directly traceable to the International System of Units (SI). As a consequence of this approach, these materials can be used in the instruments calibration, estimation of measurement uncertainty, method validation, assessment of performance of analysts, quality control routines and interlaboratory comparison programmes. The most advanced methods and techniques in mass spectrometry, that is, gas source mass spectrometry (GSMS), thermal ionisation mass spectrometry (TIMS) and inductively coupled plasma mass spectrometry (ICPMS) were investigated to identify which are the dominant components in the uncertainty and to quantify its contribution to the final value of the measurement uncertainty of the isotopic ratio. The results obtained were then compared to verify which are the methods and techniques associated to the lowest measurement uncertainty values. The isotope amount ratio n({sup 235}U)/n({sup 238}U) was certified in the materials produced to expanded uncertainties ranging from 0.02 to 0.10 % and the ratios n({sup 234}U)/n({sup 238}U) and n({sup 236}U)/n({sup 238}U), to uncertainties ranging from 0.03 to 2.20 %. These values fully comply to the requirements of the isotopic characterization of nuclear fuel as well as the analysis of environmental samples for nuclear safeguards. (author)

  15. Preparation and characterization of hybrid materials from natural chrysotile; Preparacao e caracterizacao de materiais hibridos a partir da crisotila natural

    Energy Technology Data Exchange (ETDEWEB)

    Giraldelli, M.G.; Silva, M.L.C.P., E-mail: marciogiraldelli@hotmail.co [Universidade de Sao Paulo (EEL/USP), Lorena, SP (Brazil). Escola de Engenharia

    2010-07-01

    Special attention has been given to the development of new materials from natural chrysotile. This fiber has about 40% silicon oxide in its structure with an outer layer of brucite (MgOH{sub 2}). With the aim of obtaining a material with a more uniform structure, acid leaching was performed to remove the outer layer of brucite, resulting in a silicon oxide hydrate. This material was used as support for the deposition of Nb{sub 2}O{sub 5}.nH{sub 2}O. The Nb{sub 2}O{sub 5}.nH{sub 2}O was prepared by conventional precipitation using as starting material niobium metallic. In this study, we performed the synthesis and characterization of the material SiO{sub 2}.nH{sub 2}O / Nb{sub 2}O{sub 5}.nH{sub 2}O 1:1. Both chrysotile as niobium are widely available national resources, which confirms the economic viability of resource use. The materials studied were characterized by XRD, SEM and TG/DTG. (author)

  16. Organophosphorus pentavalent compounds: history, synthetic methods of preparation and application as insecticides and antitumor agents; Compostos organofosforados pentavalentes: historico, metodos sinteticos de preparacao e aplicacoes como inseticidas e agentes antitumorais

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Viviane Martins Rebello dos; Donnici, Claudio Luis [Universidade Federal de Minas Gerais, Belo Horizonte, MG (Brazil). Dept. de Quimica; DaCosta, Joao Batista Neves; Caixeiro, Janaina Marques Rodrigues [Universidade Federal Rural do Rio de Janeiro, Seropedica, RJ (Brazil). Dept. de Quimica]. E-mail: dacosta@ufrrj.br

    2007-01-15

    This paper is a review of the history, synthesis and application of organophosphorus compounds, especially of those of pentavalent phosphorus, such as phosphoramidates, phosphorothioates, phosphonates and phosphonic acids with insecticide and anticancer activities. The organophosphorus compounds with agrochemical applications show great structural variety, They include not only insecticides, but also fungicides, herbicides, and others. The large variety of commercially available organophosphorus pesticides is remarkable. Even more interesting is the high efficiency of some organophosphorus compounds as anticancer agents such as cyclophosphamide and its derivatives. (author)

  17. Purification and preparation of bismuth(III) iodide for application as radiation semiconductor detector; Purificacao e preparacao do cristal semicondutor de iodeto de bismuto para aplicacao como detector de radiacao

    Energy Technology Data Exchange (ETDEWEB)

    Ferraz, Caue de Mello

    2016-11-01

    This study describes the experimental procedure of a BiI{sub 3} purification method powder, aiming a future application of these semiconductor crystals as room temperature radiation detector. The Repeated Vertical Bridgman Technique was applied for the purification, based on the melting and nucleation phenomena. An ampoule filled with a maximum of 25% by volume of BiI{sub 3} powder was mounted into the Bridgman furnace and vertically moved at a speed of 2 millimeters per hour, inside the furnace with programmed thermal gradient and temperature profile, at a temperature maximum of 530 deg C. The reduction of the impurities in the BiI{sub 3}, each purification, was analysed by Instrumental Neutron Activation Analysis (INAA), in order to evaluate the efficiency of the purification technique established in this work, for trace metal impurities. It was demonstrated that the Repeated Bridgman is effective to reduce the concentration of many impurities in BiI{sub 3}, such as Ag, As, Br, Cr, K, Mo, Na and Sb. The crystalline structure of the BiI{sub 3} crystal purified twice and third times was similar to the BiI{sub 3} pattern. However, for BiI{sub 3} powder and purified once an intensity contribution of the BiOI was observed in the diffractograms. It is known that semiconductor detectors fabricated from high purity crystal exhibit significant improvement in their performance compared to those produced from low purity crystals. (author)

  18. Preparation and characterization of Nafion - TiO{sub 2} composite electrolytes for application in proton exchange membrane fuel cells; Preparacao e caracterizacao de eletrolitos compositos Nafion - TiO{sub 2} para aplicacao em celulas a combustivel de membrana de troca protonica

    Energy Technology Data Exchange (ETDEWEB)

    Matos, Bruno Ribeiro de

    2008-11-06

    The fabrication and characterization of Nafion - TiO{sub 2} composites, and the use of such electrolytes in PEM (Proton Exchange Membrane) fuel cell operating at high temperature (130 deg C) were studied. The operation of a PEM fuel cell at such high temperature is considered as an effective way to promote fast electrode reaction kinetics, high diffusional transport, and high tolerance to the carbon monoxide fuel contaminant. The polymer Nafion{sup R} is the most used electrolyte in PEM fuel cells due to its high proton conductivity. However, the proton transport in Nafion is dependent on the water content in the polymeric membrane. The need of absorbed water in the polymer structure limits the operation of the fuel cell to temperatures close to 100 deg C, above which Nafion exhibits a fast decrease of the ionic conductivity. In order to increase the performance of the electrolyte operating at high temperatures, Nafion-TiO{sub 2} composites have been prepared by casting. The addition of titania hygroscopic particles to the polymeric matrix aims at the enhancement of the humidification of the electrolyte at temperatures above 100 deg C. Three types of titania particles with different specific surface area and morphology have been investigated. Nafion-based composites with the addition of titania nanoparticles, in the 2.5-15 wt.% range, with nearly spherical shape and specific surface area up to approx. 115 m{sup 2}g{sup -1} were found to have higher glass transition temperature than the polymer. Such an increase improves the stability of the electrolyte during the fuel cell operation at high temperatures. The addition of titania-derived nanotubes results in a pronounced increase of the performance of PEM fuel cell operating at 130 deg C. In this composite, the high specific surface area and the tubular shape of the inorganic phase are responsible for the measured increase of both the absorption and retention of water of the composite electrolyte. Nonetheless, the polarization curves of fuel cell using the composite electrolytes exhibited an increase of the ohmic polarization associated with the addition of the insulating titania particles. As the chemical structure of Nafion was observed to be insensitive to the addition of the inorganic particles, the high performance of the composite electrolytes is a result of competing effects: the decrease of the electrical conductivity and a higher thermal stability or water absorption/retention capacity. The experimental results suggest that the Nafion-TiO{sub 2} composites are promising electrolytes for PEM fuel cells operating at temperatures above approx. 100 deg C. (author)

  19. Characterization of isolated communities: application in the city of Ubatuba, Sao Paulo state, Brazil; Caracterizacao de comunidades isoladas: aplicacao em comunicade de Ubatura/SP

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira, Maria Julita Guerra [Secretaria de Estado de Energia, Recursos Hidricos e Saneamento (SERHS), Sao Paulo, SP (Brazil)], e-mail: mjulita@sp.gov.br; Pilla, Adelina Teixeira Fonseca de [Equilibrio, Desenvolvimento Ambiental Ltda., Sao Paulo, SP (Brazil)], e-mail: adelina.fonseca@uol.com.br

    2004-07-01

    This paper presents a methodology for characterization of isolated communities, developed on a consultant work for the Ministry of Mines and Energy - MME. It still presents the application of this methodology of analysis on a isolated community in the city of Ubatuba, Sao Paulo state. (author)

  20. Obtaining and characterization of chitosan biocomposites / HAP for application as biomaterial; Obtencao e caracterizacao de biocomposito quitosana/hidroxiapatita para aplicacao como biomaterial

    Energy Technology Data Exchange (ETDEWEB)

    Leal, R.C.A.; Nascimento, I.V.S.R.; Fook, M.V.L.; Furtado, G.T.F.S., E-mail: ritaalvesleal@hotmail.com [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Departamento de Engenharia de Materiais

    2011-07-01

    The hydroxyapatite is one of the most biocompatible materials known by encouraging bone growth. However, the main drawback it is the poor mechanical strength. A method to overcome this problem is the addition of the biopolymer chitosan, suitable for applications as biomaterials. In this study was obtained a hydroxyapatite - chitosan biocomposites for application as a biomaterial. In the FTIR analysis it was identified characteristic bands of hydroxyapatite and a possible overlap of the amino group of chitosan by carbonate. XRD analysis showed that there was no change in the profile of HA after chitosan incorporation. In SEM analysis of the biocomposites HA / chitosan, it is observed that there wasn't a complete dispersion of HA particles in the chitosan. In the image of calcined biocomposite, it was found that after heat treatment at 900 ° C chitosan was eliminated, resulting in a porous material. The analysis has shown that the presence of chitosan did not cause significant changes in the phase of hydroxyapatite. (author)

  1. Characterization of quartzite waste and their application on red ceramic; Caracterizacao de residuo de quartzitos e sua aplicacao em ceramica vermelha

    Energy Technology Data Exchange (ETDEWEB)

    Babisk, M.P.; Vidal, F.W.H., E-mail: mbabisk@cetem.gov.br [Centro de Tecnologia Mineral (CETEM/MCT), Rio de Janeiro, RJ (Brazil); Vieira, C.M.F.; Ribeiro, W.S. [Universidade Estadual do Norte Fluminense Darcy Ribeiro (UENF), Campos dos Goytacazes, RJ (Brazil)

    2012-07-01

    The incorporation of industrial waste into red ceramic have been used currently in the search for alternative raw materials, and also seeking for an environmentally friendly waste disposal that pollute. During the process of beneficiation of dimension stone, there are significant losses of material and waste generation, which have been placed inappropriately in nature, with no provision for use or reuse. The quartzite is geologically classified as a metamorphic rock composed almost entirely of quartz grains. The aim of this study is to characterize and evaluate the applicability of quartzite waste in the red ceramic. Incorporations were studied up to 40% by weight of waste in the ceramics body and the results indicated that the residue of quartz is a material with great potential to be used as a component in a red ceramic. (author)

  2. Synthesis and characterization of nanocomposites ZnO / polypyrrole for anti corrosive application; Sintese e caracterizacao de nanocompositos ZnO/polipirrol para aplicacao anticorrosivas

    Energy Technology Data Exchange (ETDEWEB)

    Valenca, D.P.; Bouchonneau, N.; Vieira, M.R.S.; Alves, K.G.B.; Melo, C.P. de; Urtiga Filho, S.L., E-mail: demetriusvalenca@gmail.com [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil)

    2014-07-01

    Nanoparticles of metal oxides and conductive polymers have been investigated as alternative additives in corrosion protection of oxidizable metals. In this hybrid nanocomposites work Polypyrrole-ZnO were synthesized and characterized as a potential application as industrial paint anti corrosive additive. The different steps of the synthesis and characterization of nanocomposites are described. The nanocomposites were obtained from the emulsion polymerization of aqueous solutions of pyrrole and sodium dodecyl sulfate containing ZnO nanoparticles dispersed in the mass. The nanoparticles were characterized by scanning electron microscopy and transmission, dynamic light scattering, diffraction of X-rays and techniques of infrared spectroscopy. From the characterization techniques, it was possible to determine the average size of nanoparticles of ZnO and ZnO-Polypyrrole. The peaks in the diffraction pattern of X-rays observed in the nanocomposite were the same as in ZnO, confirming the presence of ZnO in the composite. (author)

  3. Characterization of OSL dosemeters for application in dose evaluation in computerized tomography procedures; Caracterizacao de dosimetros OSL para aplicacao em avaliacoes de doses em procedimentos de tomografia computadorizada

    Energy Technology Data Exchange (ETDEWEB)

    Martins, Louise M.G.; Santos, Josilene C.; Umisedo, Nancy K.; Terini, RIcardo A.; Costa, Paulo R. [Universidade de Sao Paulo (USP), SP (Brazil). Instituto de Fisica

    2016-07-01

    This work aims to present results of the characterization of Al{sub 2}O{sub 3}:C optically stimulated luminescent detector (OSLD). The following aspects were studied: sensitivity, energy response and air kerma dependence in computed tomography (CT) energy range. The main objective of this work is to evaluate the applicability of this kind of dosimeter for CT organ dose assessment. The energy response showed a non-homogenous pattern which has already been found in literature. The air kerma dependence of OSL signal showed a linear trend. Concerning their sensitivity, it was observed that the same batch can have different responses for the same quality, after a second irradiation step, which shows that this kind of detector should be used with care in case of more than one irradiation. (author)

  4. Synthesis, characterization and electrical properties of solid electrolyte for solid oxide fuel cell; Preparacao, caracterizacao e propriedades eletricas de eletrolito solido para celula a combustivel de oxido solido

    Energy Technology Data Exchange (ETDEWEB)

    Berton, Marco Antonio Coelho; Garcia, Carlos Mario; Matos, Jeferson Hrenechen [Instituto de Tecnologia para o Desenvolvimento (LACTEC), Curitiba, PR (Brazil)], Emails: felsky@latec.org.br, garcia@latec.org.br, jeferson.h@latec.org.br

    2010-04-15

    Solid electrolytes of BaCe{sub 08}Gd{sub O29} were prepared by the polymeric precursor method. X-ray diffraction data shows a single phase with orthorhombic crystalline structure. The densification process was followed by scanning electronic microscopy and apparent density measurements. The apparent density was developed for different temperatures of sintering, reaching > 96% for sintered temperature of 1550 {sup 0}C deg . The electrochemical impedance analysis was development in the temperature of 400-700 deg C, in air atmosphere at 700 deg C a value of 30,6 mS.cm{sup -1} was obtained. The results of conductivity have confirmed the gadolinium doped barium cerate has a great potential for use as solid electrolyte for intermediate temperature solid oxide fuel cell, at experimental controlled conditions. (author)

  5. Preparation and characterization of polymer nanocomposites based on chitosan and clay minerals; Preparacao e caracterizacao de nanocompositos polimerico baseados em quitosana e argilo minerais

    Energy Technology Data Exchange (ETDEWEB)

    Fiori, Ana Paula Santos de Melo; Gabiraba, Victor Parizio; Praxedes, Ana Paula Perdigao [Instituto Federal de Alagoas (IFAL), Marechal Deodoro, AL (Brazil); Nunes, Marcelo Ramon da Silva; Balliano, Tatiane L.; Silva, Rosanny Christhinny da; Tonholo, Josealdo; Ribeiro, Adriana Santos, E-mail: aribeiro@qui.ufal.br [Universidade Federal de Alagoas (UFAL), Maceio, AL (Brazil)

    2014-09-15

    In this work nanocomposites based on chitosan and different clays were prepared using polyethyleneglycol (PEG) as plasticizer. The samples obtained were characterized by Fourier Transform Infrared Spectroscopy (FTIR), X-Ray Diffraction (XRD), Scanning Electron Microscopy (SEM), thermogravimetric analysis (TGA/DTG) and by mechanical characterization (tensile test) with the aim of investigating the interactions between chitosan and clay. The nanocomposite films prepared using sodium bentonite (Ben) showed an increase of 81.2% in the maximum tensile stress values and a decrease of 16.0% in the Young’s modulus when compared to the chitosan with PEG (QuiPEG) films, evidencing that the introduction of the clay into the polymer matrix provided a more flexible and resistant film, whose elongation at break was 93.6% higher than for the QuiPEG film. (author)

  6. Preparation and characterization of bentonite clays mixture destined to the removal of heavy metals; Preparacao e caracterizacao da mistura de argilas bentoniticas destinadas a remocao de metais pesados

    Energy Technology Data Exchange (ETDEWEB)

    Almeida Neto, A.F. de; Silva, M.G.C. da, E-mail: ambrosio@feq.unicamp.b [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Fac. de Engenharia Quimica. Dept. de Termofluidodinamica

    2009-07-01

    In this work a mixture was prepared with 50% wt. of the Bofe and Verde-lodo clays. The characterization methods used they were: thermal analyses (TG and DTG), X-ray diffraction, fisissorption of N{sub 2}, scanning electron microscopy and X-ray energy dispersive spectroscopy. The rehearsals of adsorption we accomplished in system of finite bath using as adsorbent the mixture loamy in natura or it mixes calcined. Starting from TG and DTG a thermal treatment was accomplished to 500 deg C of the loamy mixture. Through the results of the copper adsorption, it was verified that mixes loamy it provokes chemical precipitation of the copper while the calcined sample presents amount metal adsorbed around 7.31 mg of copper/g of adsorbent. The value of removal percentage obtained by the calcined sample it was of 63.02%. (author)

  7. Synthesis and characterization of lead oxides for preparation of nanocomposites with polyamide; Sintese e caracterizacao de oxido de chumbo para preparacao de nanocompositos com poliamida

    Energy Technology Data Exchange (ETDEWEB)

    Cado, Ronan Gorski; Severo, Vinicius A.; Bulhores, Luis Otavio S. [Centro Universitario Franciscano, Santa Maria, RS (Brazil). Programa de Pos-Graduacao em Nanociencias. Lab. de Desenvolvimento de Materiais Nanoestruturados

    2016-07-01

    Lead oxide nanoparticles with diameters between 100 to 250 nm were obtained using a polymeric precursor method in the presence of citric acid and ethylene glycol. X-ray diffraction (XRD) and dynamic light scattering to measure the size and zeta potential in solution in dispersions with different pH were used to characterize the as-obtained samples. The nanoparticles were incorporated into polyamide 6.6 and composite films were prepared by electrospinning being evaluated the variation of the mechanical properties of the polymer and its effectiveness in attenuation of X-rays. (author)

  8. Resveratrol-loaded poly({epsilon}-caprolactone) microparticles: preparation and characterization; Microparticulas de poli({epsilon}-caprolactona) contendo resveratrol: preparacao e caracterizacao

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    Resveratrol-loaded poly({epsilon}-caprolactone) (PCL) microparticles were obtained by simple emulsion/solvent evaporation method. Three drug-loaded formulations were prepared with the aim of investigating the influence of composition on the encapsulation efficiency. Morphological and spectroscopic methods were performed for these materials. The microparticles revealed residual moisture close to 1.5% and encapsulation efficiency above 80%. Spherical shape and smooth surface were observed by SEM. No pores were either verified. Resveratrol-loaded microparticles showed an average particle size of around 50 {mu}m. X-ray diffraction analysis demonstrated that the microencapsulation reduced the drug crystallinity. The FTIR results suggest that no chemical bond was formed between polymer and drug. (author)

  9. Synthesis and characterization of Pt-Sn-Ni alloys to application as catalysts for direct ethanol fuel cells; Sintese e caracterizacao de ligas de Pt-Sn-Ni para aplicacao como caztalisadores em celulas a combustivel do tipo DEFC

    Energy Technology Data Exchange (ETDEWEB)

    Silva, E.L. da; Correa, P.S.; Oliveira, E.L. de; Takimi, A.S.; Malfatti, C.F., E-mail: celia.malfatti@ufrgs.b [Universidade Federal do Rio Grande do Sul (LAPEC/UFRGS), Porto Alegre, RS (Brazil). Programa de Pos-Graduacao em Engenharia Mecanica. Lab. de Pesquisa em Corrosao; Radtke, C. [Universidade Federal do Rio Grande do Sul (IQ/UFRGS), Porto Alegre, RS (Brazil). Inst. de Quimica

    2010-07-01

    Direct ethanol fuel cells (DEFCs) have been the focus of recent research due its application in mobile energy sources. In order to obtain the maximum efficiency from these systems, it is necessary the total ethanol oxidation, which implies in C-C bond break. Different catalysts described in literature are employed with this intent. This work consists in studying PtSnNi catalysts supported on carbon Vulcan XC72R, to application in DEFCs. Thus, it was used the impregnation/reduction method, varying the atomic proportion among Pt, Sn and Ni. The alloys were characterized by X-Ray Diffraction, Cyclic Voltammetry and Transmission Microscopy. Preliminary results show that predominant structure on the catalysts is the face centered cubic platinum and the densities currents are dependent on the platinum amount. (author)

  10. Synthesis and characterization of sulfonic acid membranes based on interpenetrating polymer networks for application in fuel cells; Sintese e caracterizacao de membranas sulfonadas baseadas em redes polimericas interpenetrantes para aplicacao em celulas a combustivel

    Energy Technology Data Exchange (ETDEWEB)

    Blanco, Lyzed Toloza; Loureiro, Felipe A.M.; Rocco, Ana Maria [Grupo de Materiais Condutores e Energia, Escola de Quimica, Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil)], e-mail: amrocco@eq.ufrj.br; Pereira, Robson Pacheco [Instituto de Ciencias Exatas, Universidade Federal Fluminense (UFF), Volta Redonda, RJ (Brazil)

    2011-07-01

    In the present work, the synthesis and characterization of sulfonic membranes based on interpenetrating polymer networks (IPN). In order to obtain such systems, the diglycidyl ether of bisphenol A (DGEBA) was polymerized in presence of polyethyleneimine (PEI). These membranes were submitted to sulfonation reactions, originating IPN-SO{sub 3}H membranes. The characterization by FTIR evidenced the formation of a Semi-IPN structure, while sulfonation reactions resulted in systems containing -SO{sub 3}H groups covalently bonded to the chains. The membranes exhibited water retention up to 200 degree C, in a temperature range sufficient for application in PEMFC under hydration. (author)

  11. Fabrication and electrical characterization of polyaniline-silicon heterojunction for gamma radiation dosimetry application; Fabricacao e caracterizacao eletrica de heterojuncoes de polianilina - silicio para aplicacao em dosimetria de radiacao gama

    Energy Technology Data Exchange (ETDEWEB)

    Laranjeira, Jane Maria Goncalves

    2004-08-15

    In this work a technique has been developed to fabricate high quality polyaniline-silicon heterojunction diodes for use as gas and/or ionizing radiation sensors. Polyaniline thin films (40 nm thick) produced by spin-coating on silicon substrates, were the active part of the junction structure. The devices presented excellent reproducibility of their electrical characteristics with high rectification ratio, 60,000 at {+-}1.0 V, and typical reverse current at - 1.0 V of 3 nA at 295 K. A G/I x G plot has been used to analyze the current-voltage characteristics, yielding typical series resistance of 4 k{omega} {+-} 5% and ideality factor in a range of 1,9 {+-} 0.5%. The heterojunction diode presents high sensitivity to gamma radiation in the dose range of 3 x 10{sup -2} to 7 kGy with a linear response in the forward and reverse bias. The excellent electrical characteristics together with the linear response with the dose, strongly suggest the application of this device for spectrometry or dosimetry of high doses of gamma radiation. These devices presented high sensitivity to gas moistures such as ammonia, nitric acid and trichloroethylene. In both cases the sensitivity was observed through shifts of the current-voltage curves, which can be easily monitored to provide a calibration curve of the sensor either as a radiation dosimeter or as a gas sensor for use in applications for gas monitoring or radiation dosimetry. Several aspects of the reliability physics of silicon-polyaniline heterojunction, such as degradation effects induced by local heating, charge trapping and temperature changes, have been discussed. These results further confirm the quality of the devices electrical characteristics and their suitability for radiation and gas sensors applications. Another interesting results presented in this work was the use of polyemeraldine nanofilms (thickness in the range 30-50 nm) deposited by 'spin coating' on glass substrates as an optical dosimeter for

  12. Synthesis and characterization of hydroxyapatite porous matrixes for application as radiation sources in brachytherapy; Sintese e caracterizacao de matrizes porosas de hidroxiapatita para aplicacao como fontes radioativas em braquiterapia

    Energy Technology Data Exchange (ETDEWEB)

    Lacerda, Kassio Andre; Lameiras, Fernando Soares; Silva, Viviane Viana [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)]. E-mail: kassiolacerda@yahoo.com.br

    2006-04-15

    Porous ceramic materials based on calcium phosphate compounds (CPC) have been studied aiming at different biomedical applications such as implants, drug delivery systems and radioactive sources for brachytherapy. Two kinds of hydroxyapatite (HAp) powders and their ceramic bodies were characterized by a combination of different techniques (X-rays diffraction and fluorescence, infrared spectrophotometry, BET method, thermal analysis, and scanning electron microscopy) to evaluate their physico-chemical and microstructural characteristics in terms of chemical composition, segregated phases, microstructure, porosity, and chemical and thermal stability. The results revealed that these systems presented potential for use as porous biodegradable radioactive sources able to be loaded with a wide range of radionuclides for cancer treatment by the brachytherapy technique. (author)

  13. Obtaining and electrical characterization of silicone/barium titanate composite for variable capacitor applications; Obtencao e caracterizacao eletrica de composito silicone/titanato de bario para aplicacoes em capacitor variavel

    Energy Technology Data Exchange (ETDEWEB)

    Vieira, D.A.; Souza, P.S.S.; Souza, C.P., E-mail: debora.vieira@cear.ufpb.br [Universidade Federal da Paraiba (UFPB), Joao Pessoa, PB (Brazil). Centro de Energias Alternativas e Renovaveis. Departamento de Engenharia Eletrica; Menezes, P.C.F. [Universidade Federal de Campina Grande (UFCG), Campina Grande, PB (Brazil). Departamento de Engenharia de Materiais

    2014-07-01

    Silicone/barium titanate composites are excellent candidates for applications in the production of electronics components. In this work, silicone/barium titanate composite was obtained for the production of capacitors with variable dielectric distance. The mixture of composite (20% of barium titanate) was performed in a mixer with stem type propellers, at room temperature for 20 minutes. The cure was held in vacuum kiln. After obtaining the composite, was mounted a parallel plate capacitor, using composite as dielectric. The composite obtained was subjected to x-ray diffraction, scanning electron microscopy and capacitive electrical test. The DRX confirms the presence of ceramic charge in composite with the presence of broad peaks of barium titanate and micrographs show the barium titanate particles dispersed in polymer matrix. The capacitance of the sample was approximately 28,7pF. (author)

  14. Synthesis and characterization of LDH/Ppi composite and its application as adsorbent of 2,4-dichlorophenoxyacetic (herbicide); Sintese e caracterizacao do composito HDL/Ppi e sua aplicacao como adsorvente do 2,4-diclorofenoxiacetico (herbicida)

    Energy Technology Data Exchange (ETDEWEB)

    Pacheco, I.S.; Oliveira, R.S.; Girotto, L.G.; Freitas, L.L. de; Amaral, F.A. do; Canobre, S.C., E-mail: ingrid_1194@hotmail.com [Universidade Federal de Uberlandia (UFU), MG (Brazil). Instituto de Quimica

    2016-07-01

    This work had as main objective the synthesis and characterization of LDH [Co-Al-Cl] method by hydrolysis of urea and then its synthesized polypyrrole coating by chemically targeting the application as adsorbent dichlorophenoxyacetic acid (2,4-D). The x-ray diffractogram of well defined showed diffraction peaks corresponding to the planes 003, 006, 009 and 110 which allow them to rhombohedral indexes and lamellar structure. The composite LDH / Ppi had a percentage of 49% herbicide retention in aqueous solution. From the investigated adsorption isotherm models that more fit the experimental data was the Freundlich, so it could be inferred that the interaction between the LDH / Ppi and the herbicide was physical, ie an rapid, reversible adsorption and does not specify. (author)

  15. Chemometrics application in fuel's MTR type chemical characterization by X-ray fluorescence; Aplicacao da quimiometria para caracterizacao quimica de combustiveis tipo MTR por fluorescencia de raios-X

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Clayton Pereira da

    2012-07-01

    In Brazil and worldwide the nuclear power has occupied a prominent position with many applications in industry, power generation, environment and medicine, improving the quality of tests and treatments, therefore people's lives. Uranium is the main element used in nuclear facilities and it s employed as base material to generation of electricity in the manufacture of radiopharmaceuticals. In the '50s, during the Cold War, the then newly created International Atomic Energy Agency proposed to oversee nuclear facilities and encourage the manufacture of nuclear fuels with low-enriched uranium (LEU) fuel came then type Material Test Reactor (MTR), manufactured initially in U{sub 3}O{sub 8} and U{sub 3}Si{sub 2} later, both dispersed in aluminum. The use of this technology requires a constant improvement of all processes involving the manufacture of MTR subject to several international protocols, which seek to ensure the reliability of the fuel from the standpoint of practical and environmental. In this context, the control of impurities, from the point of view of neutron economy, directly affects the quality of any nuclear fuel, so strict control is necessary. The literature has reported procedures which, beyond generating residues, are lengthy and costly, they need calibration curve and consequently reference materials. The aim of this work is to establish and validate a methodology for nondestructive quantitative chemical analysis, low cost and analysis time, as well as minimize the generation of waste, for multielement determination of major constituents (Utotal and Si) and impurities (B, Mg, Al, Cr, Mn, Fe, Co, Ni, Cu, Zn, Mo, Cd and others) present in U3O8 and U{sub 3}Si{sub 2}, meeting the needs of nuclear reactors in the nuclear fuel qualification type MTR. For that purposes, will be applied the X-ray fluorescence technique which allows fast chemical and nondestructive analysis, aside from sample preparation procedures that do not require previous

  16. Preparation and characterization of a composite based on Zr(IV) and phosphoric acid; Preparacao e caracterizacao de um composito a base de Zr(IV) e acido fosforico

    Energy Technology Data Exchange (ETDEWEB)

    Silveira, T.F.S. da; Carmo, D.R. do, E-mail: taylafserantoni@gmail.com [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Ilha Solteira, SP (Brazil). Faculdade de Engenharia. Departamento de Fisica e Quimica

    2014-07-01

    The present work describes the preparation and characterization of a composite formed from zirconium (IV) isopropoxide and phosphoric acid (ZrP). This composite (ZrP) was characterized by techniques such as infrared spectroscopy (FTIR), {sup 13}C and {sup 31}P nuclear magnetic resonance (NMR), X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDS) and thermogravimetric analysis (TG). Vibrational spectrum for ZrP showed a band at ∼ 1010 cm{sup -1} assigned to the stretching P=O(νP=O). The results obtained by EDS confirmed the presence of elements Zr, P and O in the formed composite, and any C has been detected in concordance of NMR of {sup 13}C. The {sup 31}P NMR spectrum of ZrP showed two pronounced peaks characteristic of zirconium phosphate. In the TG curve three steps of weight loss were observed for ZrP. (author)

  17. Preparation and characterization of high density polyethylene and residual fibre of Attalea funifera Mart (piacava) composites; Preparacao e caracterizacao de compositos de polietileno de alta densidade com residuos de fibras de piacava da especie Attalea funifera Mart

    Energy Technology Data Exchange (ETDEWEB)

    Agrela, Sara P.; Guimaraes, Danilo H.; Jose, Nadia M., E-mail: saraagrela@hotmail.co [Universidade Federal da Bahia (GECIM/IQ/UFBA), Salvador, BA (Brazil). Inst. de Quimica. Grupo de Energia e Ciencias dos Materiais; Carvalho, Gleidson G.P. [Universidade Federal da Bahia (UFBA), Salvador, BA (Brazil). Escola de Medicina Veterinaria. Dept. de Producao Animal; Carvalho, Ricardo F. [Universidade Federal da Bahia (EP/UFBA), Salvador, BA (Brazil). Escola Politecnica. Curso de Mestrado em Engenharia Ambiental Urbana

    2009-07-01

    The use of natural fiber reinforcement thermoplastic polymer is continuously increasing. This fact is manly due to its advantages as low cost, availability, recyclability, low energy demand and then environmental appeal if compared to synthetics fibers. The composites were prepared in different fiber volume ratios (5%, 10% and 20%) mixed with high density polyethylene (HDPE) and heated at 190 deg C. Thermogravimetric analysis and differential scanning calorimetry were used to investigate thermal stability. The composites structure was characterized by Fourier Transform Infrared spectroscopy, X-ray diffractometry. Fiber and residue of piassava (Attalea funifera Mart) chemical composition were determined by Van Soest Method. The results indicate that thermo stability of the composites of HDPE prepared with fiber volume ratios up to 20% is only slightly lowered. (author)

  18. Methyl biodiesel from Dipteryx lacunifera: preparation, characterization and effect of antioxidant on the oxidation stability; Biodiesel metilico de Dipteryx lacunifera: preparacao, caracterizacao e efeito de antioxidantes na estabilidade a oxidacao

    Energy Technology Data Exchange (ETDEWEB)

    Araujo, Francisca Diana da Silva; Moura, Carla Veronica Rodarte de; Chaves, Mariana H., E-mail: mariana@ufpi.edu.b [Universidade Federal do Piaui (UFPI), Teresina, PI (Brazil). Dept. de Quimica

    2010-07-01

    The objective of this work was to study the potentialities of Dipteryx lacunifera Ducke seeds oil for biodiesel production. The yield in oil was of 46.11 {+-} 0.37%. Methyl biodiesel was prepared by base catalyzed transesterification yielding 88.13% and percentage conversion of triglycerides to corresponding methyl ester of 89.1%. The addition of the tertiary butylhydroquinone (TBHQ, 50 ppm), butylated hydroxytoluene (BHT, 50 ppm) and cashew nut shell liquid (CNSL, 2000 ppm) antioxidants in the biodiesel contributed to the increase of the induction period of 2.97 h for 8.08; 6.06 and 6.02 h, respectively. (author)

  19. Synthesis and characterization of rare earth molybdates nanoparticles for detection of specific prostatic cancer (PSA); Preparacao e caracterizacao de nanoparticulas de molibdatos de terras raras para deteccao do antigeno especifico da prostata (PSA)

    Energy Technology Data Exchange (ETDEWEB)

    Dias, Clarissa Lombardi

    2013-07-01

    The interest in using rare earths to investigate the properties and functions of biochemical systems as well as to determinate biological substances has increased in several fields, including biomarkers in immunology (fluoro immunoassays). Nowadays the use of lanthanides in the diagnosis of various diseases have become more important through the development of commercial diagnostic kits. As main feature, these rare earths can show a long lifetime, photo stability and emission bands of atomic like behavior and well defined, in the visible region, demonstrating unique advantages when compared to other luminescent species. The present work had as its goal to synthesize rare earth molybdates by the co-precipitation method as well as to characterize these materials by X-ray diffraction, near infrared spectroscopy, thermogravimetric analysis, scanning electronic microscopy, transmission electronic microscopy and luminescent studies. In this work, three different studied were developed: the influence of the vortex speed variation during co-precipitation in the structure of the final product, morphology and luminescence properties; the influence of the annealing temperature also in the structure, morphology and luminescence properties; and the influence of concentration of the doping in the luminescence properties. Another important step of this work was the functionalization of nanoparticles using an organosilane (APTES) to coat and establish points for binding the particles to biological species. It was proved that this process was very efficient by the characterization results and the silica incorporation was well succeeded. Specific prostatic cancer (PSA) was then linked to the functionalized nanoparticles to diagnostic prostatic cancer by fluoroimmunoassay and levels for detection were established. (author)

  20. Preparation and physico-chemical characterization of inclusion complexes between local anesthetics and hydroxypropyl-{beta}-cyclodextrin; Preparacao e caracterizacao fisico-quimica de complexos de inclusao entre anestesicos locais e hidroxipropil-{beta}-ciclodextrina

    Energy Technology Data Exchange (ETDEWEB)

    Moraes, Carolina Morales; Abrami, Priscila; Goncalves, Marcos Moises; Andreo Filho, Newton [Universidade de Sorocaba, SP (Brazil); Fernandes, Sergio Antonio; Paula, Eneida de [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Inst. de Biologia. Dept. de Bioquimica; Fraceto, Leonardo Fernandes [UNESP, Sorocaba, SP (Brazil). Dept. de Engenharia Ambiental]. E-mail: leonardo@sorocaba.unesp.br

    2007-07-15

    S(-) Bupivacaine (S(-)BVC) and Lidocaine (LDC) are widely used local anesthetics (LA). Hydroxypropyl {beta}-cyclodextrin (HP-{beta}-CD) is used as a drug-carrier system. The aim of this work was to characterize inclusion complexes between LA and HP-{beta}-CD. The affinity constants determined at different pHs show favourable complexation. The release kinetics experiments showed that S(-)BVC and LDC changed the released profiles in the presence of HP-{beta}-CD. Nuclear magnetic resonance experiments gave information about the interaction between LA and the cyclodextrin cavity. This study focused on the physicochemical characterization of drug-delivery formulations that come out as potentially new therapeutic options for pain treatment. (author)

  1. Study of (Fe/HZM-5) catalyst be used in the Fischer-Tropsch synthesis: preparation and characterization; Estudo do catalisador (Fe/HZSM-5) a ser utilizado na sintese de Fischer-Tropsch: preparacao e caracterizacao

    Energy Technology Data Exchange (ETDEWEB)

    Gonzaga, Arthur C. [Universidade Estadual do Maranhao (UEMA0), MA (Brazil); Sousa, Bianca V. de; Lima, Wellington S.; Rodrigues, Meiry G.F. [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Unidade Academica de Engenharia Quimica

    2008-07-01

    In this work it was developed an iron catalyst supported on the ZSM-5 zeolite to be used in the Fischer-Tropsch Synthesis (FTS). The NH{sub 4}{sup +}ZSM-5 zeolitic support was submitted to the wet impregnation, using the 0.1 M of the Fe(NO{sub 3}){sub 3}.9H{sub 2}O solution to obtain the Fe/NH{sub 4}{sup +}ZSM-5 sample in the content of iron 5% wt. After, the material was submitted for the drying process and in the following, for the calcination one, obtaining the Fe/HZSM-5 form. The EDS characterization analyses showed that in the Fe/HZSM-5 sample the iron is in the Fe{sub 2}O{sub 3} form and that the impregnation and calcination processes did not cause significant exchanges in the zeolitic support framework. The results of the N{sub 2} physical adsorption of the 5% Fe/HZSM-5 showed the presence of the micropores and mesopores. From these results, the obtained material (5% Fe/HZSM-5) presents a great potential to be used like a catalyst in the FTS. (author)

  2. Co-coagulation of the NBR latex and clay aqueous suspension: preparation and characterization;Co-coagulacao de latex de NBR e suspensao aquosa de argila: preparacao e caracterizacao

    Energy Technology Data Exchange (ETDEWEB)

    Reis, Raquel S.; Brum, Elisson; Silva, Vanessa M. [Nitriflex S/A Industria e Comercio, Rio de Janeiro, RJ (Brazil); Souza, Diego H.S.; Gomes, Ailton de S.; Nunes, Regina C.R., E-mail: rcnunes@ima.ufrj.b [Universidade Federal do Rio de Janeiro (IMA/UFRJ), RJ (Brazil). Inst. de Macromoleculas Profa. Eloisa Mano

    2009-07-01

    Blends of nitrile rubber (NBR) and sodium montmorillonite (MMT-Na) were prepared by co-coagulation of the NBR latex with aqueous suspension of clay. The content of MMT was varied from 0 to 7 phr and different mixtures were analyzed by X-ray diffraction, light scattering, gel content, thermogravimetric analysis and the oscillating disk rheometer. The different methods used indicated that there was formation of a structure interspersed in the mixtures studied, and that increasing the content MMT-Na enhances the values obtained. Rheological measurements on compositions with NBR showed the influence of clay on increasing the time of healing in terms of its content, as is the gel content and the thermal resistance. All results were compared to composition of NBR without MMT. (author)

  3. Study and development of nanocomposites PBT/bentonite clay treated by ionizing radiation: preparation and characterization; Estudo e desenvolvimento de nanocompositos PBT/argila bentonita tratados por radiacao ionizante: preparacao e caracterizacao

    Energy Technology Data Exchange (ETDEWEB)

    Sartori, Mariana do Nascimento

    2014-07-01

    This work describes the preparation and characterization of composites based on poly (butylene terephthalate) - PBT and brazilian modified clay prepared by the melt intercalation. PBT nanocomposites with 3 and 5 % by weight of organically modified clay, by the addition of a quaternary ammonium salt, were prepared by extrusion using a twin-screw extruder machine. After the extrusion process, the materials were injected to obtain specimens tests samples for the characterization tests. Part of the specimens samples were irradiated using an electron beam accelerator with 1.5 MeV at room temperature in the presence of air. Samples of pure PBT and irradiated and non-irradiated nanocomposites were characterized by mechanical tests of tensile, flexural and impact, heat distortion temperature (HDT), X - ray diffraction (XRD), scanning electron microscopy (SEM), melt flow index (MFI) thermogravimetry (TG) and differential scanning calorimetry (DSC) and the correlation between the properties was discussed. The results showed that the addition of clay, in both percentages, promoted an increase greater than 50 % in tensile strength at break and a gain of around 35% in heat distortion temperature when compared to the pure polymer. The treatment with ionizing radiation of electron beam at the doses used in this study showed no significant changes in material properties. (author)

  4. Synthesis and characterization of polyamide and polyester, from glycerol and dicarboxylic acids, polymeric blends;Preparacao e caracterizacao de blendas de poliamida e poliesteres a base de glicerol e acidos dicarboxilicos

    Energy Technology Data Exchange (ETDEWEB)

    Brioude, Michel M.; Bresciani, Danusa; Guimaraes, Danilo H.; Jose, Nadia M., E-mail: mbrioude@gmail.co [Universidade Federal da Bahia (UFBA), Salvador, BA (Brazil); Prado, Luis A.S.A. [Technische Universitaet Hamburg, Harburg (Germany). Inst. of Polymer and Composites

    2009-07-01

    In this work were prepared and characterized polyamide and polyester blends. The polyester, called PAT, was produced in a becker equipped with high-torque mechanical stirrer, thermometer and condenser Claisen, by adding of glycerol, adipic acid, terephthalic acid and catalyst. The blends films were prepared by physical mixture followed by thermal compression. The polymeric blends and the pure materials were characterized by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that the blends are semi-crystalline and have good thermal behavior, besides, it evidences that the PAT and polyamide phases are immiscible. (author)

  5. Preparation and characterization of electrocatalysts based on palladium for electro-oxidation of alcohols in alkaline medium; Preparacao e caracterizacao de eletrocatalisadores a base de paladio para oxidacao eletroquimica de alcoois em meio alcalino

    Energy Technology Data Exchange (ETDEWEB)

    Brandalise, Michele

    2012-07-01

    In this study Pd/C, Au/C, PdAu/C, PdAuPt/C, PdAuBi/C and PdAuIr/C electrocatalysts were prepared by the sodium borohydride reduction method for the electrochemical oxidation of methanol, ethanol and ethylene glycol. This methodology consists in mix an alkaline solution of sodium borohydride to a mixture containing water/isopropyl alcohol, metallic precursors and the Vulcan XC 72 carbon support. The electrocatalysts were characterized by energy dispersive X-ray (EDX), X-ray diffraction (XRD), transmission electron microscopy (TEM) and cyclic voltammetry. The electrochemical oxidation of the alcohols was studied by chronoamperometry using a thin porous coating technique. The mechanism of ethanol electro-oxidation was studied by Fourier Transformed Infrared (FTIR) in situ. The most effective electrocatalysts were tested in alkaline single cells directly fed with methanol, ethanol or ethylene glycol. Preliminary studies showed that the most suitable atomic composition for preparing the ternary catalysts is 50:45:05. Electrochemical data in alkaline medium show that the electrocatalysts PdAuPt/C (50:45:05) showed the better activity for methanol electro oxidation, while PdAuIr/C was the most active for ethanol oxidation and PdAuBi/C (50:45:05) was the most effective for ethylene glycol oxidation in alkaline medium. These results show that the addition of gold in the composition of electrocatalysts increases their catalytic activities. The spectroelectrochemical FTIR in situ data permitted to conclude that C-C bond is not broken and the acetate is formed. (author)

  6. Preparation and electrical characterization of electrolytes obtained from solid solution (Zr{sub 0.84}Y{sub 0.16O1.90}) x (Ce{sub 0.80}Gd{sub 0.20}O{sub 1.90}){sub 1-x} for fuel cells application; Preparacao e caracterizacao eletrica de eletrolitos obtidos a partir da solucao solida (Zr{sub 0.84}Y{sub 0.16O1.90}) x (Ce{sub 0.80}Gd{sub 0.20}O{sub 1.90}){sub 1-x} para aplicacao em pilhas de combustivel

    Energy Technology Data Exchange (ETDEWEB)

    Tonelli, Bruno C.; Antunes, Fabio C.; Souza, Dulcina P.F. de, E-mail: fcaufscar@yahoo.com.b [Universidade Federal de Sao Carlos (LAPCEC/UFSCar), SP (Brazil). Programa de Pos-Graduacao em Ciencia e Engenharia de Materiais. Lab. de Preparacao e Caracterizacao Eletrica em Ceramicas

    2010-07-01

    Oxide fuel cells based on yttria stabilized zirconia (YSZ) operates near 1000 deg C. This high temperature results in physical and chemical degradation of the device. Rare earths doped ceria (REC) based systems can operate at low temperatures due to higher ionic conductivity. However, at low oxygen partial pressure, doped ceria shows n-type electronic conductivity due to reduction of Ce{sup +4} to Ce{sup +3}. Trying to put together the zirconia and ceria advantage, YSZ-REC composites have been investigated. In this work, YSZ-GdDC powders mixtures were prepared and pellets were isostatically pressed. Pellets were sintered 1100-1500 deg C temperature range. Sintered pellets were characterized by density measurements, X-ray diffraction, impedance spectroscopy and scanning electron microscopy. The experimental procedure adopted in this work generated solid solutions instead of composite samples. Nevertheless, the composition containing {approx}76 vol.% of YSZ, in spite of the high porosity, showed electrical conductivity similar to pure YSZ. (author)

  7. Preparation and characterization of novel nanocomposites of inorganic/polysaccharide type =

    Science.gov (United States)

    Oliveira, Fabiane Costa

    O uso de polimeros naturais no ambito da preparacao de nanocompositos nao tem sido tao amplamente estudado quando comparado com os polimeros sinteticos. Assim, esta tese tem como objectivo estudar metodologias para a preparacao de novos materiais nanocompositos sob a forma de dispersoes e filmes utilizando polissacarideos como matriz. A tese esta dividida em cinco capitulos sendo o ultimo capitulo dedicado as conclusoes gerais e a sugestoes para trabalhos futuros. Inicialmente e apresentada uma breve revisao bibliografica sobre os principais temas colocando esta tese em contexto. Consideracoes sobre o uso de polimeros naturais e a sua combinacao com a utilizacao de nanoparticulas inorganicas para a fabricacao de novos bionanocomposites sao descritas e os objectivos e outline da tese sao tambem apresentados. No segundo capitulo, a preparacao de particulas de silica puras ou modificadas bem como a sua caracterizacao por FTIR, SEM, TEM, TGA, DLS (tamanho e potencial zeta) e medicoes de angulo de contacto sao discutidas. De modo a melhorar a compatibilidade da silica com os polissacarideos, as particulas SiO2 foram modificados com dois compostos do tipo organosilano: 3- metacril-oxipropil-trimetoxissilano (MPS) e 3-aminopropil-trimetoxissilano (APS). As particulas SiO2 MPS foram posteriormente encapsuladas com de poli(metacrilato de glicidilo) utilizando a tecnica de polimerizacao em emulsao. A utilizacao dos nanocompositos resultantes na preparacao de dispersoes de bionanocompositos nao foi bem sucedida e por esse motivo nao os estudos nao foram prosseguidos. O uso de SiO2 APS na preparacao de dispersoes bionanocomposite foi eficiente. No terceiro capitulo e apresentada uma revisao sobre dispersoes bionanocompositas e respectiva caracterizacao destacando aspectos fundamentais sobre reologia e microestrutura. Em seguida, e discutido o estudo sistematico realizado sobre o comportamento reologico de dispersoes de SiO2 utilizando tres polissacarideos distintos no que

  8. Characterization of Lanthanum Ferric Cobaltite doped with Strontium (LSCF) films deposited by spray-pyrolysis for application as cathode in PaCOS-TI; Caracterizacao de filmes de CFLE depositados por spray-pirolise para utilizacao como catodo em PaCOS-TI

    Energy Technology Data Exchange (ETDEWEB)

    Almeida, L.S.; Guimaraes, V.F.; Paes Junior, H.R. [Universidade Estadual do Norte Fluminense Darcy Ribeiro (UENF), Campos dos Goytacazes, RJ (Brazil). Lab. de Materiais Avancados], Emails: laryssadsa@yahoo.com.br, valtencyguimaraes@yahoo.com.br, herval@uenf.br

    2010-07-01

    The lanthanum ferric cobaltite doped with strontium (LSCF) is a ceramic material with the perovskite structure that stands out in the field of research for its use as cathode in solid oxide fuel cells at intermediate temperatures (IT-SOFC). The films were synthesized by spray-pyrolysis technique on 8% mol Yttria stabilized zirconia (YSZ) substrates. It was studied the influence of heat treatment temperatures (600-1000 deg C) on the properties of the films under the conditions of treatment during four hours. Samples were tested electrically by measuring the variation of electrical conductivity with temperature, structurally by X-ray diffraction (XRD) and morphologically by scanning electron microscopy (SEM). The films heat treated at 700 deg C for 4 hours showed better performance for application as cathode. (author)

  9. Characterization of residues of effluent treatment plant from lapping process of soda-lime glass and its application in the production of concrete; Caracterizacao de residuo de estacao de tratamento de efluentes de processo de lapidacao de vidro sodo-calcico e sua aplicacao na producao de concreto

    Energy Technology Data Exchange (ETDEWEB)

    Antonio, Aline Pignaton; Calmon, Joao Luiz; Tristao, Fernando Avancini, E-mail: apignaton@hotmail.com, E-mail: calmonbarcelona@gmail.com, E-mail: fernandoavancini@ct.ufes.br [Universidade Federal do Espirito Santo (UFES), Vitoria, ES (Brazil). Programa de Pos-Graduacao em Engenharia Civil

    2012-07-01

    This study enunciates the physical, chemical and mineralogical composition of the residue from the process of ETE cutting of soda-lime glasses and its application in concrete as a replacement to the weight of CPV ARI RS cement, at levels of 0, 5, 10, 15 and 20%. Tests were performed on fresh and hardened (ages 3, 7, 28 and 300 days). The results were compared and statistically analyzed. In the fresh state, reductions in the amount of exuding water and consistency were observed. The results of compressive strength were statistically different, while the results for the tensile strength by diametrical compression and modulus of elasticity results were belonging to homogeneous groups. Beneficial effects the levels of residue on the cementitious matrix and the transition zone of concrete were identified by SEM, particularly concrete in S15.

  10. Production and characterization of compounds based on MgB{sub 4}O{sub 7} for application in dosimetry; Producao e caracterizacao de compostos a base de MgB{sub 4}O{sub 7} para aplicacao em dosimetria

    Energy Technology Data Exchange (ETDEWEB)

    Souza, Luiza Freire de

    2016-07-01

    Many materials with luminescent properties are used for ionizing radiation dosimetry through the thermoluminescence (TL) and optically stimulated luminescence (OSL) techniques. Detectors based on lithium fluoride (LiF), calcium sulphate (CaSO{sub 4}) and aluminum oxide (Al{sub 2}O{sub 3}), doped or codoped with various elements, are the TL or OSL commercial dosimeters most widely used currently. However, several researches are focused to the development of new TL /OSL materials in intention to enhance the dosimetric properties, in view that no TL/OSL dosimeter has all the ideal characteristics for monitoring the radiation. In this context, magnesium tetraborate (MgB{sub 4}O{sub 7}), which has been presented in the literature as a material for dosimetry TL, was investigated in this work. As there are no reports on the structural characterization of this material or regarding to its applicability on OSL dosimetry, the proposal of the present work was to develop compounds based on MgB{sub 4}O{sub 7}, with different doping, by solid state synthesis. It was made the structural, optical, TL and OSL characterization of the compound to verify it feasibility for application on radiation dosimetry. Initially, it was determined the calcination temperature and time for MgB{sub 4}O{sub 7} formation, with the use of thermal analyses and x ray diffraction. The ideal calcination was found at 900 °C for 7 hours. It were produced , in powder form, the compounds: MgB{sub 4}O{sub 7}, MgB{sub 4}O{sub 7}:Dy, MgB{sub 4}O{sub 7}:Dy,Li, MgB{sub 4}O{sub 7}:Ce, MgB{sub 4}O{sub 7}:Ce,Li, MgB{sub 4}O{sub 7}:Nd and MgB{sub 4}O{sub 7}:Nd,Li. For TL and OSL analyses it were produced pellets sintering at 950 °C for 2 hours. The radioluminescence (RL) analyses of MgB{sub 4}O{sub 7}:Dy and MgB{sub 4}O{sub 7}:Dy,Li shows wavelength emissions at 490, 590, 670 and 760 nm. For MgB{sub 4}O{sub 7}:Ce and MgB{sub 4}O{sub 7}:Ce,Li RL was observed wide emission band in the ultraviolet region. For the Mg

  11. Optical and structural characterization of the pure and doped BaY{sub 2}F{sub 8} with rare earths for application in radiation detectors and scintillators; Caracterizacao optica e estrutural do BaY{sub 2}F{sub 8} puro e dopado com terras raras visando aplicacao em detectores de radiacao e cintiladores

    Energy Technology Data Exchange (ETDEWEB)

    Mello, Ana Carolina Santana de

    2008-07-01

    In this work Barium Yttrium Fluoride (BaY{sub 2}F{sub 8} -BaYF) doped with different concentrations of ions Tb{sup 3+}, Er{sup 3+}, Tm{sup 3+} e Nd{sup 3+} were characterized, aiming the application in radiation detection devices that use the scintillating properties. Two types of samples were produced in the CLA-IPEN-SP, polycrystalline samples, obtained via solid state reaction of BaF{sub 2} and YF{sub 3} under HF atmosphere, and single crystals, obtained via the zone melting method also in a HF atmosphere. The samples were characterized using the following experimental techniques: X-ray powder diffraction, Radioluminescence (RL), Optical Absorption and Dispersive X-ray Absorption Spectroscopy (DXAS). The X-ray diffraction pattern showed the presence of the phase BaY{sub 2}F{sub 8} and a small amount of the phase Ba{sub 4}Y{sub 3}F{sub 17} in the polycrystalline pure and Tb{sup 3+}doped samples. The other samples showed only the desired BaY{sub 2}F{sub 8} phase. The radioluminescence measurements of the doped BaYF, when irradiated with X-rays, showed emission peaks in energies that are characteristics of the 4f-4f transitions of rare earths. The RL of the samples with 2 mol por cent and 3 mold of Tb{sup 3+}showed quite intense peaks with a maximum emission peak at 545 nm. The Tm{sup 3+}doped BYF showed that the scintillation efficiency is not directly proportional to the doping level, and the highest RL emission were obtained for the polycrystalline samples doped with 1 mol por cent, showing a maximum peak intensity at 456 nm (the blue region of the visible spectrum). All samples showed a phosphorescent decay time of the order of seconds. Single crystals of BaYF doped with 2 mol por cent of Er{sup 3+}, in addition to one of the highest phosphorescence time, presents a quite strong Rl in the green region of the spectra. The radiation damage was evaluated by the optical absorption techniques and the results showed that the formation of the absorption bands can be

  12. Preparation and characterization of asymmetric membranes of poly (vinylidene fluoride) supported in polyester - I: effect of heat treatment in the properties of membranes; Preparacao e caracterizacao de membranas assimetricas de poli (fluoreto de vinilideno) suportadas em poliester - I: efeito do tratamento termico nas propriedades das membranas

    Energy Technology Data Exchange (ETDEWEB)

    Thuermer, Monica B.; Poletto, Patricia; Marcolin, Marcos; Ferreira, Daiane G.; Zeni, Mara [Universidade de Caxias do Sul (CCET/UCS), RS (Brazil). Centro de Ciencias Exatas e Tecnologia], E-mail: mzandrad@ucs.br

    2010-07-15

    Poly(Vinylidene Fluoride) (PVDF) is a semicrystalline polymer containing an amorphous and a crystalline phase. This characteristic is important for the preparation of asymmetric membranes, because the crystalline phase has great influence on the membranes structure, while the amorphous phase affects the porosity. PVDF membranes were prepared by the phase inversion process, which were then evaluated with regard to permeability and morphology, as well as the thermal treatment effect. The following membranes were compared: without thermal treatment, with thermal treatment and commercially-available membrane. The analysis of chemical resistance, water permeability flux to different pressures and diffusion of ions, in addition to studies with Scanning Electron Microscopy (SEM), Differential Scanning Calorimetry (DSC) and Thermogravimetric Analysis (TGA), were performed to investigate the membranes properties. (author)

  13. Preparation of mesoporous silica films SBA-15 over different substrates; Preparacao de filmes de silica mesoporosa SBA-15 sobre diferentes substratos

    Energy Technology Data Exchange (ETDEWEB)

    Campos, V.O.; Sousa, E.M.B. de; Macedo, W.A.A., E-mail: vitorcampos@ufmg.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil). Servico de Nanotecnologia

    2010-07-01

    Mesoporous materials have been target of frequent interest due to its wide application possibilities, for example development of gas sensors, catalysis, molecules transportation, pharmaceuticals release, synthesis of auto-organized nanostructures, among others. The possibilities of application are enhanced when such materials are disposed in the form of thin and ultrathin films. In this work the preparation of mesoporous SBA-15 silica films is explored by means of the dipcoating technique of a sol-gel on different substrates (glass slides, stainless steel, copper), using the surfactant poly(ethylene glycol)-block-poly(propylene glycol)- block-poly(ethylene glycol), known as P123, a block copolymer. Synthesis parameters surfactant concentration, aging time and temperature were investigated. In this work we present the morphological and structural characterization of the prepared films, which were obtained using atomic force microscopy and x-ray fluorescence and diffraction. (author)

  14. Preparation of microspheres containing methyl methacrylate (MMA) with magnetic nanoparticles; Preparacao de microesferas contendo metacrilato de metila (PMMA) com nanoparticulas magneticas

    Energy Technology Data Exchange (ETDEWEB)

    Feuser, P.E.; Souza, M.N. de, E-mail: paulofeuser@hotmail.co, E-mail: nele@eq.ufrj.b [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Dept. de Engenharia Quimica

    2010-07-01

    Magnetic nanoparticles have found many technological applications and has been intensively studied due to its special magnetic properties. In most biomedical applications, microspheres containing magnetic nanoparticles is used as a vehicle for transporting drugs, presenting several advantages when compared to other conventional methods. PMMA is a polymer which has biocompatibility and can be used for the encapsulation of magnetic nanoparticles, showing a great degree of saturation magnetization. PMMA microparticles containing magnetic nanoparticles were prepared by suspension polymerization. Polymers containing magnetic nanoparticles were characterized by X-ray diffraction (XRD), vibrating sample magnetization, thermogravimetric analysis, optical microscopy, chromatography gel permeation, analysis of particle size - malversizer 2000 (Malvern Instruments). The average size of magnetic nanoparticles was approximately 150 {mu}m and depending on the amount of magnetic nanoparticles in the reaction medium Mw of microspheres can be altered. (author)

  15. Characteristics of ornamental rocks waste: application of mechanochemical concepts; Caracterizacao de residuos de rochas ornamentais: aplicacao de conceitos mecanoquimicos

    Energy Technology Data Exchange (ETDEWEB)

    Santos, J. dos; Galembeck, F., E-mail: jsquimica@gmail.com [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Instituto de Quimica

    2016-07-01

    Processing of ornamental rocks produces up to 80% weight residues which become an environmental problem. In this work, we analyzed residual powders from cutting and crushing granite Cinza Corumba, to study the influence of mechanical processes in the properties of the residues. The powders were characterized by X-ray diffraction and fluorescence, infrared spectroscopy, scanning electron microscopy, surface area determination and adsorption of methylene blue. The same elements and minerals are found in both powders but the powders formed during crushing contain lubricating oil residues, from the crusher. Particle shapes of the crushed powder (surface area 2.85 m2/g) are more irregular than cut powder (surface area 1.98 m2/g). Adsorption of methylene blue is lighter in the crushed powder than in the cutting powder. Thus, the powders analyzed have different surface properties. (author)

  16. Study for preparation of nanoporous titania on titanium by anodic oxidation; Estudo da preparacao de titania nanoporosa sobre titanio por oxidacao anodica

    Energy Technology Data Exchange (ETDEWEB)

    Passos, Alessandra Pires

    2014-07-01

    Currently titanium is the most common material used in dental, orthopedic implants and cardiovascular applications. In the mid 1960s, prof. Braenemark and coworkers developed the concept of osseointegration, meaning the direct structural and functional connection between living bone and the surface of artificial implant. Thus, studies on the modification of the implant surface are widely distributed among them are the acid attack, blasting with particles of titanium oxide or aluminum oxide, coating with bioactive materials such as hydroxyapatite, and the anodic oxidation. The focus of this work was to investigate the treatment of titanium surface by anodic oxidation. The aim was to develop a nanoporous titanium oxide overlay with controlled properties over titanium substrates. Recent results have shown that such surface treatment improves the biological interaction at the interface bone-implant besides protecting the titanium further oxidation and allow a faster osseointegration. The anodizing process was done in the potentiostatic mode, using an electrolyte composed of 1.0 mol/L H{sub 3}PO{sub 4} and HF 0.5% m/I. The investigated process parameters were the electrical potential (Va) and the process time (T). The electric potential was varied from 10 V to 30 V and the process time was defined as 1.0 h, 1.5 h or 2.0 h. The treated Ti samples were characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM), energy dispersive spectroscopy X-ray (EDS), and X-ray diffraction (XRD). The results showed the formation of nanoporous titanium oxide by anodizing with electric potential (Va) in the range of 20 V to 30 V and process time in the range of 1 to 2 hours. The average pore diameter was in the range 94-128 nm. Samples anodized in electric potential lower than 20 V did not show the formation of the nanoporous surface. In the case of Va above 30 V, it was observed the formation of agglomerates of TiO{sub 2}. The results obtained in this study

  17. Physicochemical characterization of purple banana fiber; Caracterizacao fisico-quimica de fibra de bananeira roxa

    Energy Technology Data Exchange (ETDEWEB)

    Goncalves, A.P.B.; Guimaraes, D.H.; Miranda, C.S.; Oliveira, J.C.; Cruz, A.M.F.; Luporini, S.; Jose, N.M., E-mail: anapaulabispo43@yahoo.com.br [Universidade Federal da Bahia (GECIM/UFBA), Salvador, BA (Brazil). Programa de Pos-Graduacao em Engenharia Quimica. Grupo de Energia e Ciencias dos Materiais

    2014-07-01

    Due to the environmental appeal that has grown in recent years, researches involving the use of renewable sources raw materials reaffirm this need. The vegetable fibers has excelled as promising materials with possibilities in different applications. The objective of this work is the evaluation of the physicochemical properties of banana fiber. These fibers were extracted from the banana pseudostem of a species not yet reported in the literature, Musa velutina, known as purple banana. For this experiment were used in natura fibers and processed fibers with NaOH 5% which were characterized by TGA, DSC, DRX and FTIR analysis. In the thermal analysis, both tested fibers showed good thermal properties. In DRX analysis, the processed fibers showed higher crystallinity. The use of these materials implies adding value to an agricultural waste in addition to being a more ecologically correct proposal. (author)

  18. Characterization of TEMPO-oxidized bacterial cellulose; Caracterizacao de celulose bacteriana tempo-oxidada

    Energy Technology Data Exchange (ETDEWEB)

    Nascimento, Eligenes S.; Pereira, Andre L.S.; Lima, Helder L.; Barroso, Maria K. de A., E-mail: eligenessampaio@hotmail.com [Universidade Federal Ceara (UFC), Fortaleza, CE (Brazil); Barros, Matheus de O. [Instituto Federal do Ceara (IFCE), Fortaleza, CE (Brazil); Morais, Joao P.S. [Embrapa Algodao, Campina Grande, PB (Brazil); Borges, Maria de F.; Rosa, Morsyleide de F. [Embrapa Agroindustria Tropical, Fortaleza, CE (Brazil)

    2015-07-01

    The aim of this study was to characterize the TEMPO-oxidized bacterial cellulose, as a preliminary research for further application in nanocomposites. Bacterial cellulose (BC) was selectively oxidized at C-6 carbon by TEMPO radical. Oxidized bacterial cellulose (BCOX) was characterized by TGA, FTIR, XRD, and zeta potential. BCOX suspension was stable at pH 7.0, presented a crystallinity index of 83%, in spite of 92% of BC, because of decrease in the free hydroxyl number. FTIR spectra showed characteristic BC bands and, in addition, band of carboxylic group, proving the oxidation. BCOX DTG showed, in addition to characteristic BC thermal events, a maximum degradation peak at 233 °C, related to sodium anhydro-glucuronate groups formed during the cellulose oxidation. Thus, BC can be TEMPO-oxidized without great loss in its structure and properties. (author)

  19. Synthesis and characterization of boron nitrides nanotubes; Sintese e caracterizacao de nanotubos de nitreto de boro

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira, T.H.; Sousa, E.M.B. [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil). Servico de Nanotecnologia

    2010-07-01

    This paper presents a new synthesis for the production of boron nitride nanotubes (BNNT) from boron powder, ammonium nitrate and hematite tube furnace CVD method. The samples were subjected to some characterization techniques as infrared spectroscopy, thermal analysis, X-ray diffraction and scanning electron microscopy and transmission. By analyzing the results can explain the chemical reactions involved in the process and confirm the formation of BNNT with several layers and about 30 nanometers in diameter. Due to excellent mechanical properties and its chemical and thermal stability this material is promising for various applications. However, BNNT has received much less attention than carbon nanotubes, it is because of great difficulty to synthesize appreciable quantities from the techniques currently known, and this is one of the main reasons this work.(author)

  20. Synthesis and characterization of new ionic liquids; Sintese e caracterizacao de novos liquidos ionicos

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, L.M.C. de; Mattedi, S.; Boaventura, J.S., E-mail: luanaufrn@hotmail.co [Universidade Federal da Bahia (UFBA), Salvador, BA (Brazil). Escola Politecnica. Programa de Pos-Graduacao em Engenharia Quimica; Iglesias, M. [Universidade Federal da Bahia (UFBA), Salvador, BA (Brazil). Escola Politecnica. Programa de Pos-Graduacao em Engenharia Quimica; Universidad de Santiago de Compostela (Spain). Escuela Tecnica Superior de Ingenieria. Dept. de Ingenieria Quimica

    2010-07-01

    In recent years, ionic liquids have been highlighted for its potential in various industrial applications. Among them, the salts of Broensted has a promising profile for the low toxicity, low cost and simple synthesis. This paper presents the synthesis and characterization of new salts of Bronsted with branched (lactate) or large chain anions (oleate) for future use as additives promoters of proton conductivity in fuel cells of ethanol. Experimental data were measured for density, sound velocity and conductivity of pure ionic liquids and mixtures. The density decreases linearly with increasing temperature, and sound velocity shows a similar trend, but not linear. The conductivity increases according to the Arrhenius model with activation energy less than 10 J/mol. Tests NMR, FTIR and TGA confirm ionic structure and thermal stability up to 165 deg C. (author)

  1. Preparation of PtSn/C, PtRu/C, PtRh/C, PtRuRh/C and PtSnRh/C electrocatalysts using an alcohol-reduction process for methanol and ethanol oxidation; Preparacao e caracterizacao de eletrocatalisadores PtRu, PtSn, PtRh, PtRuRh e PtSnRh para oxidacao direta de alcoois em celulas a combustivel tipo PEM utilizando a metodologia da reducao por alcool

    Energy Technology Data Exchange (ETDEWEB)

    Dias, Ricardo Rodrigues

    2009-07-01

    In this work, Pt/C, PtRh (90:10), PtRh/C (50:50), PtSn/C (50:50), PtRu (50:50)/C, PtRuRh/C (50:40:10) and PtSnRh/C (50:40:10) were prepared by an alcohol-reduction process with metal loading of 20 wt.% using H{sub 2}PtCl{sub 6}.6H{sub 2}O (Aldrich), SnCl{sub 2}.2H{sub 2}O (Aldrich),and RhCl{sub 2}.XH{sub 2}O (Aldrich) as metals sources and Vulcan XC72 as support. The electrocatalysts were characterized by EDX, XRD and cyclic voltammetry (CV). The electro-oxidation of ethanol was studied by CV, chronoamperomety at room temperature in acid medium and tests at 100 deg C on a single cell of a direct methanol or ethanol fuel cell. The EDX analysis showed that the metal atomic ratios of the obtained electrocatalysts were similar to the nominal atomic ratios used in the preparation. The diffractograms of electrocatalysts prepared showed four peaks at approximately 2{theta} =40 deg, 47 deg, 67 deg and 82 deg, which are associated with the (111), (200), (220) and (311) planes, respectively, of a face cubic-centered (fcc) structure characteristic of platinum and platinum alloys. The average crystallite sizes using the Scherrer equation and the calculated values were in the range of 2-3 nm. For Pt Sn/C and PtSnRh/C two additional peaks were observed at 2 = 34 deg and 52 deg that were identified as a SnO{sub 2} phase. Pt Sn/C (50:50) and PtSnRh/C (50:40:10) electro catalyst showed the best performance for ethanol oxidation at room temperature. For methanol oxidation at room temperature Pt Ru/C, Pt Sn/C and PtRuRh/C electrocatalysts showed the best performance. Tests at 100 deg C on a single cell of a direct ethanol fuel cell PtSnRh/C showed the best performance, for methanol oxidation PtRuRh/C showed the best performance. (author)

  2. Preparation and characterization of electroluminescent devices based on complexes of {beta}-diketonates of Tb{sup 3+}, Eu{sup 3+}, Gd{sup 3+} ions with macrocyclic ligands and UO{sub 2}{sup 2+} films; Preparacao e caracterizacao de dispositivos eletroluminescentes de complexos de {beta}-dicetonados de ions Tb{sup 3+}, Eu{sup 3+}, Gd{sup 3+} com ligantes macrociclicos e filmes de UO{sub 2}{sup 2+}

    Energy Technology Data Exchange (ETDEWEB)

    Gibelli, Edison Bessa

    2010-07-01

    Complexes containing Rare Earth ions are of great interest in the manufacture of electro luminescent devices as organic light emitting devices (OLED). These devices, using rare earth trivalent ions (TR{sup 3+}) as emitting centers, show high luminescence with extremely fine spectral bands due to the structure of their energy levels, long life time and high quantum efficiency. This work reports the preparation of Rare Earth {beta}-diketonate complexes (Tb{sup 3+}, Eu{sup 3+} and Gd{sup 3+}) and (tta - thenoyltrifluoroacetonate and acac - acetylacetonate) containing a ligand macrocyclic crown ether (DB18C6 - dibenzo18coroa6) and polymer films of UO{sub 2}{sup 2+}. The materials were characterized by complexometric titration with EDTA, CH elemental analysis, near infrared absorption spectroscopy, thermal analysis, X-ray diffraction (powder method) and luminescence spectroscopy. For manufacturing the OLED it was used the technique of deposition of thin films by physical vapor (PVD, Physical Vapor Deposition). (author)

  3. Characterization of nanocomposites PHBV/attapulgite organophilic; Caracterizacao de nanocompositos PHBV/atapulgita organofilica

    Energy Technology Data Exchange (ETDEWEB)

    Silva, L.C.A.; Barreto, L.S., E-mail: lilianealcantara@msn.co [Universidade Federal de Sergipe (UFS), Sao Cristovao, SE (Brazil). Programa de Pos-graduacao em Ciencia e Engenharia de Materiais; Thire, R.M.S.M. [Coordenacao dos Programas de Pos-Graduacao de Engenharia (PEMM/COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Engenharia Metalurgica e de Materiais

    2010-07-01

    Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) - PHBV is a biodegradable polyester which have been studied as an option for the production of disposable goods. This thermoplastic has some disadvantages that limit its use in industrial scale applications: the relative difficulty of processing, high degree of crystallinity and high cost of production relative to conventional polymers. An alternative to improve the properties of PHBV is the incorporation of small amounts of clay to the polymer. The aim of this work was to produce and characterize PHBV nanocomposites reinforced with organophilic attapulgite in different compositions. Natural attapulgite was modified with hexadecylmethylammonium chloride. The nanocomposites were characterized by XRD, SEM and Thermal analysis. It was observed reduction of the degree of crystallinity, melting and glass transition temperatures and the thermal stability of polymer in function on the addition of clay to the matrix of the PHBV. The best results were obtained for PHBV films containing 3% and 5% attapulgite. These films presented a slight increasing in processing window and decreasing in crystalline temperature and in degree of crystallinity as compared to pure PHBV. (author)

  4. Synthesis and characterization of biomorphic ceramics; Sintese e caracterizacao de ceramicas biomorficas

    Energy Technology Data Exchange (ETDEWEB)

    Rambo, Carlos Renato

    2001-07-01

    Biotemplating represents a recently developed technology for manufacturing of biomorphous ceramics from naturally grown plant structures. This approach allows the production of ceramic materials with cellular structure, where the microstructural features of the ceramic product are similar to the native plant. After processing, the biomorphic ceramic exhibits directed pore morphology in the micrometer range. Biomorphic SiC fibers were produced from bamboo by carbothermal reduction of SiO{sub 2} originally present in the bamboo structure. Bamboo pieces were heated up to 1500 deg C in argon to promote the reaction between carbon and silica. Biomorphic alumina, mullite and zirconia ceramics were manufactured via the sol-gel route by repeated infiltration of low viscous oxide precursors (sols) into rattan, pine and bamboo structures. The raw samples were pyrolyzed at 800 deg C in nitrogen for 1h and subsequently annealed at 1550 deg C in air. The microstructure and physical properties of the biomorphic ceramics were characterized by X-ray diffraction (XRD) and high temperature-XRD, scanning electron microscopy (SEM), porosimetry and picnometry. Thermal analysis (TGA/DTA) was performed on the infiltrated samples in order to evaluate the reactions and the total weight loss during the thermal process. The mechanical properties were evaluated by compressive strength tests. In contrast to conventional processed ceramic foam of similar porosity, the microstructure highly porous biomorphic ceramics shows uniaxial pore morphology with anisotropic properties. These properties are favorable for applications in catalyst support, filters or low-density heat insulation structures, or as biomaterials. (author)

  5. Atomic layer deposition of metal oxide by non-aqueous sol-gel chemistry =

    Science.gov (United States)

    Marichy, Catherine

    O trabalho apresentado neste manuscrito foi desenvolvido no ambito do programa doutoral intitulado “Deposicao de Camadas Atomicas (ALD) de oxido de metais por sol-gel nao-aquoso”. O objectivo deste trabalho foi a preparacao de hetero-estruturas funcionais por ALD e a sua caracterizacao. Foi desenvolvido um novo processo de deposicao de oxido de estanho a temperatura baixa-moderada, utilizando um metodo ALD nao-aquoso, o qual foi aplicado com sucesso ao revestimento controlado das paredes internas e externas de nanotubos de carbono. Uma vez que a preparacao de nanomateriais funcionais requer uma elevada exatidao do processo de deposicao, foi demonstrada a deposicao precisa de filmes que se adaptem a forma do substrato ou de filmes nano-estruturados constituidos por particulas em varios substratos. Alem disso, foram depositados com grande exatidao varios oxidos de metal em nanotubos de carbono e demonstrou-se a possibilidade de ajustar o revestimento feito por ALD atraves do controlo da funcionalizacao da superficie do substrato nano-estruturado de carbono. As hetero-estruturas obtidas foram posteriormente aplicadas como sensores de gases. O melhoramento verificado na sensibilidade foi atribuido a formacao de heterojuncoes p-n entre o filme de oxido de metais e o suporte. O trabalho desenvolvido tendo como objetivo o controlo do revestimento por ALD atraves da funcionalizacao da superficie do suporte e certamente de interesse para o design de hetero-estruturas funcionais baseadas em substratos de carbono. De facto, durante o ultimo periodo do programa de doutoramento, este conceito foi alargado a funcionalizacao e revestimento com oxidos de metal de fibras de carbono preparadas por “electrospinning”, de forma a melhorar a estabilidade e a atividade eletrocatalitica de catalisadores a base de Pt. Este trabalho foi realizado maioritariamente na Universidade de Aveiro mas tambem na Universidade Nacional de Seul e beneficiou de varias colaboracoes internacionais

  6. Preparation of Pt/USY catalysers and application in the reformation of n-octane; Preparacao de catalisadores Pt/USY e aplicacao na reforma do n-octano

    Energy Technology Data Exchange (ETDEWEB)

    Araujo, Alfredina dos S.; Sousa, Bianca V.; Grau, Javier M.; Rodrigues, Meiry Glaucia F. [Universidade Federal de Campina Grande (UFCG), PB (Brazil)

    2008-07-01

    During the catalytic reform, the hydrocarbons of long chain are reconstructed, through reactions of isomerization, hydrogenation, desidrocyclization and dehydrogenation, among others. These reactions occur in acid or metallic small farms, on a bifunctional catalyzer of type Pt/Al{sub 2}O{sub 3}-Cl. The metallic component is active in the hydrogenation and dehydrogenation, while the support (chlorinated alumine) possess acidity enough to promote isomerization reactions. The joint action of the two small farms promotes other reactions, as the desidrocyclization, through a bifunctional mechanism. Reactions also occur undesirable (hydrocracking and hydrogenation) that they diminish the selectivity and they deactivate the catalyzer for coke formation. The catalyzers most promising for this reaction are the acid zeolites of great pores, had to its textural characteristics that facilitate the access of the reagents to active small farms. In this work, the catalytic performance of the metallic function in the dehydrogenation reaction, the conversion and income in the reaction of reform of n-octane will be studied, of the catalyzers of the Pt/USY type. (author)

  7. Effect of the addition of collagen in the preparation of hydroxyapatite, aiming the application of pulp capping; Efeito da adicao de colageno na preparacao de hidroxiapatita visando a aplicacao como capeador pulpar

    Energy Technology Data Exchange (ETDEWEB)

    Ribeiro, Geysy L.; Mendes, Luis C., E-mail: geysylopes@ima.ufrj.br [Instituto de Macromoleculas Professora Eloisa Mano (IMA) - Universidade Federal do Rio de Janeiro, UFRJ. Centro de Tecnologia, RJ (Brazil)

    2011-07-01

    This work studied the action of collagen (COLL) in the hydroxyapatite (HA) synthesis, produced through sol-gel process, in order to mimetize the chemical composition of dental tissue. The resulting material was characterized by energy dispersive X-ray spectroscopy (EDX), Fourier transform infrared spectroscopy (FT-IR), wide-angle X-ray diffraction (WAXD) and scanning electron microscopy (SEM). The Ca/P ratio was determined through EDX - 1,89 e 2,38, with and without collagen, respectively. The FT-IR analysis showed no significant interaction between the constituents of the composite. The R-ray diffractograms indicated an increase of the resolution and intensity of the HA peak. The photomicrographies showed that the preparation method exhibited significantly influence onto the hydroxyapatite morphology, as well as resulted in a homogeneously dispersed composite. (author)

  8. Application of different methodologies in the preparation of organic matrices for determination of trace elements by differential pulse anodic stripping voltammetry; Aplicacao de diferentes metodologias na preparacao de matrizes organicas para a determinacao voltametrica de elementos traco

    Energy Technology Data Exchange (ETDEWEB)

    Sisti, Cristina

    2001-07-01

    The determination of trace elements in food samples is of great importance for the human health, considering the factors of essentiality and toxicity. On the other hand, the chemical analysis is largely affected for the steps of sample preparation; laboratory contamination of the sample and the reagents or still volatilization and losses of the elements. If these parameters are not controlled the achieved precision and accuracy could be low. In this work, the content of zinc, cadmium, lead and copper was determined in adults diet samples collected by duplicate portion technique and bovine liver, applying the differential pulse anodic stripping voltametry - (DP-ASV) technique. In the digestion of the matrices in acid medium, conventional methodologies were used, conductive heating in open recipients and equipment with microwaves source in open and closed vessels. The best procedure was the sample digestion by microwaves, in closed vessels and the other treatments made in controlled atmosphere with hood laminar-airflow class 100. The established methodology was validated with the use of a certified sample as reference (NIST - bovine liver 1577b). (author)

  9. Rheological characterization of nanocomposites Nylon 6/bentonite clay; Caracterizacao reologica de nanocompositos de poliamida 6/argila bentonitica

    Energy Technology Data Exchange (ETDEWEB)

    Silva, T.R.G.; Fernandes, P.C.; Oliveira, S.V., E-mail: taci_gouveia@yahoo.com.b [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Curso de Pos-Graduacao em Ciencia e Engenharia de Materiais; Araujo, E.M.; Melo, T.J.A. [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Unidade Academica de Engenharia de Materiais

    2010-07-01

    Polymer nanocomposites are a class of materials that have been widely used in various applications. Among them, has been emphasizing the preparation of polymer films with barrier properties for applications in polymer membranes. In this work, nanocomposites of nylon 6/bentonite clay were obtained from a Homogenizer, in the ratios of 1, 3 and 5 wt% clay. The Brasgel PA bentonite clay was treated organically with Praepagen HY salt, to make it organophilic. By X-ray diffraction (XRD), it was showed that the efficiency of the incorporation of salt in the clay. The rheological curves showed that for the AST clay the torque did not change when compared with the pure nylon 6, while for the clay ACT, the torque increased gradually with the percentage of clay. (author)

  10. Synthesis and characterization of sulfonated polyesters derived from glycerol; Sintese e caracterizacao de poliesteres sulfonados obtidos a partir do glicerol

    Energy Technology Data Exchange (ETDEWEB)

    Fiuza, R.A.; Jose, N.M.; Boaventura, J.S. [Universidade Federal da Bahia (IQ/UFBA), Salvador, BA (Brazil). Inst. de Quimica; Fiuza, R.P. [Universidade Federal da Bahia (EP/UFBA), Salvador, BA (Brazil). Escola Politecnica. Curso de Mestrado em Engenharia Quimica

    2010-07-01

    In this work were synthesized polyesters from glycerol and acid sulfonated phthalic previously. The materials were characterized by DSC, TGA, FTIR, SEM, XRD and XRF. The results showed effective sulfonation of phthalic acid. The presence of sulfonic groups promoted strong changes in the crystallinity of the new material makes the lens. The polyesters made from phthalic acid sulfonated combine characteristics such as heat resistance and groups that drivers potentiate the electrolyte for application in fuel cells proton exchange membrane and also for gas separation. (author)

  11. Characterization of limestone of region South and Southeast of Para; Caracterizacao de calcario da regiao Sul e Sudeste do Para

    Energy Technology Data Exchange (ETDEWEB)

    Marinho, A.R.O.; Vieira, J.H.A.; Antunes Junior, L.V.; Medeiros, A.C.; Souza, G.P., E-mail: marabaonline@gmail.com [Universidade Federal do Sul e Sudeste do Para (FEMAT/UNIFESSPA), Maraba, PA (Brazil)

    2014-07-01

    Limestone is used in daily activities, and it is common the use of products containing calcium carbonate in various applications, from construction to food production, air purification to sewage treatment, the sugar refining materials for the toothpaste, the manufacture of glass and steel in the manufacture of paper, plastics, paints, ceramics and many others. The Limestone present in the region of south and southeast of Para is presented in deposits that have not been explored on a large scale, being justified a deepening in characteristics thereof. For the characterization of the material, gross samples were comminuted by crushing and ball mill, sieved and then separated into aliquots. In the end were used fluorescence analysis of X-ray, diffraction X-rays, determination of the moisture and loss on ignition of the material at 950 °C for one hour, obtaining results of a dolomitic limestone. (author)

  12. Characterization of clay of Santa Maria Madalena-RJ (Brazil); Caracterizacao do solo do municipio de Santa Maria Madalena

    Energy Technology Data Exchange (ETDEWEB)

    Freitas, R.A.; Borges, B.F.; Rosario, S. do; Alexandre, J.; Beiral, W.V.; Anderson, R.B.; Pessanha, E.F., E-mail: jonas@uenf.br, E-mail: wevuenf@yahoo.com.br [Universidade Estadual do Norte Fluminense Darcy Ribeiro (LECIV/UENF), Campos dos Goytacazes, RJ (Brazil). Laboratorio de Engenharia Civil

    2011-07-01

    The city of Santa Maria Madalena, located in the mountainous region of Rio de Janeiro State, has a region of rocky and extensive area of native forest. Its economy is primarily intended for farming, agriculture and tourism. Characterization studies were conducted in this region, aiming to determine the optimal production process for its application in the ceramics industry. The tests were conducted in the laboratories of the Universidade Estadual Norte Fluminense Darcy Ribeiro - UENF and were determined and the physical, chemical and mineralogical characteristic. Were performed Granulometric Analysis, Atterberg Limit, Chemical Analysis, X Ray Diffraction. The specimens used in evidence were extruded and then fired at the following temperatures: 750 ° C and 850 ° C, and subsequently conducted measurements of absorption, linear shrinkage and resistance to flexion-compression. (author)

  13. Nickel coating electroplated characterization with and without carbon nanotubes; Caracterizacao de niquel eletrodepositado na presenca de nanotubos de carbono

    Energy Technology Data Exchange (ETDEWEB)

    Lopes, A.C.; Banczek, E.P.; Cunha, M.T.; Rodrigues, P.R.P. [Universidade Estadual do Centro-Oeste, Guarapuava, PR (Brazil). Dept. de Quimica; Costa, I. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil); Terada, M. [Universidade de Sao Paulo (EPUSP), SP (Brazil). Escola Politecnica. Dept. de Engenharia Metalurgica e de Materiais

    2010-07-01

    The metals have great application, but when their properties are not suitable they should be improved through treatments to increase corrosion resistance, mechanical and wear. The metals electrodeposition such as nickel is one of treatment options. This study aims the development a nickel coating with and without (CNT), obtained by electrodeposition on aluminum alloy AA6061. The nickel electrodeposition was performed with cyclic voltammetry and chronoamperometry. Open circuit potential and anodic polarization curves were carried out samples characterization. The microstructure and the chemical composition of the M{sub x}O{sub z} coating were studied using the scanning electron microscopy, energy dispersion spectroscopy and X-ray diffraction. The results indicated that the nickel coating improve the corrosion resistance of aluminum in the presence of CNT. (author)

  14. Production and characterization of poly(styrene-co-methylmethacrylate);Producao e caracterizacao de poliestireno-co-metacrilato de metila

    Energy Technology Data Exchange (ETDEWEB)

    Augustinho, Tiago R.; Coan, Thais; Abarca, Silvia A.C.; Testoni, Alex A.S.; Baumgarten, Bruno P.; Machado, Ricardo A.F., E-mail: tiagoqmc@gmail.co [Universidade Federal de Santa Catarina (UFSC), Florianopolis (Brazil). Dept. de Engenharia Quimica e Alimentos

    2009-07-01

    Polystyrene (PS) is a polymer used in diverse industrial segments. It is easy to process and has a low cost when compared to other materials. However, PS has low mechanical resistance, which limits its application in some areas. Thus, a methodology that is sufficiently used is the synthesis of a copolymer, formed of two or more monomers to get products that have characteristics that are not possible to obtain with only one monomer. In this work, the styrene and methyl methacrylate monomers had been carried through reactions of copolymerization by means of polymerization in suspension using (MMA) with styrene in a bigger percentage. MMA was selected for being a monomer that results in a polymeric configuration more resistant than the PS. The copolymerization was proven to occur by infra-red spectroscopy (IR) and Nuclear Magnetic Resonance (NMR). Different analyses were performed using different initiators, weight molar and conversion studies. (author)

  15. Obtaining and characterization of polycaprolactone with nanocellulose microcomposite; Obtencao e caracterizacao de microcompositos de policaprolactona com nanocelulose

    Energy Technology Data Exchange (ETDEWEB)

    Paz, R.A. da; Araujo, E.M., E-mail: rene@cct.ufcg.edu.br [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Unidade Academica de Engenharia de Materiais; Leite, A.M.D. [Universidade Federal do Rio Grande do Norte (UFRN), RN (Brazil). Escola de Ciencia e Tecnologia; Rosa, M.F. [Embrapa Agroindustria Tropical, Fortaleza, CE (Brazil)

    2016-07-01

    Research into the development of biodegradable materials of renewable energy sources are increasing and polycaprolactone (PCL) is a biodegradable thermoplastic which has many applications. The cellulose nanocrystals (NCC) are crystalline domains of cellulose sources and have been evaluated as reinforcement in polymer matrices for their potential to improve many properties. Micro Composites PCL with NCC were developed by by melting intercalation 3 content and 5% nanocellulose. Specimens tensile and impact were injection molded and the material was characterized by FTIR, XRD, TGA, DSC and mechanical properties. The FTIR and TGA results show the presence of load array and greater thermal stability respectively. XRD and DSC shows an increase in crystallinity. The properties: tensile and impact the system showed improvements in module, tension, and ductility of the material. (author)

  16. Application of artificial neural networks on the characterization of radioactive waste drums; Aplicacao de redes neurais artificiais na caracterizacao de tambores de rejeito radioativo

    Energy Technology Data Exchange (ETDEWEB)

    Potiens Junior, Ademar Jose; Hiromoto, Goro, E-mail: apotiens@ipen.b, E-mail: hiromoto@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2011-10-26

    The methodology consist of system simulation of drum-detector by Monte Carlo for obtention of counting efficiency. The obtained data were treated and a neural artificial network (RNA) were constructed for evaluation of total activity of drum. For method evaluation measurements were performed in ten position parallel to the drum axis and the results submitted to the RNA. The developed methodology showed to be effective for isotopic characterization of gamma emitter radioactive wastes distributed in a heterogeneous way in a 200 litters drum. The objective of this work as to develop a methodology of analyse for quantification and localization of radionuclides not homogeneous distributed in a 200 liters drum based on the mathematical techniques

  17. Characterization and potential application of pataua vegetable oil in apatite flotation; Caracterizacao e potencial aplicacao do oleo vegetal de pataua na floracao de apatita

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, P.S. de; Mansur, H.S.; Peres, A.E.C., E-mail: eng.priscila.oliveira@gmail.com [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil)

    2016-07-01

    The present research characterizes the Pataua palm (Oenocarpus bataua) oil regarding to its fatty acids profile and acidity index, and evaluates its use for apatite flotation. The Pataua oil evaluated is unsaturated e predominantly composed of cis-9-octadecenoic acid (oleic acid). The mineral sample characterization revealed a material composed by a fluoroapatite deficient in fluorine, a possibly result of isomorphic substitution, and with quartz and monazite inclusions. The analysis of the mineral after reagent conditioning, by Fourier Transform Infrared Spectroscopy (FTIR), pointed to the presence of characteristic bands of carbon chains and carboxylate group, suggesting the collector adsorption through the mechanisms of chemisorption and insoluble calcium salts precipitation. Thus, it is proposed the Pataua oil potential use in flotation systems aiming apatite recovery. (author)

  18. Characterization of products of combustion of mineral coal; Caracterizacao de produtos solidos da combustao do carvao mineral

    Energy Technology Data Exchange (ETDEWEB)

    Pinheiro, H.S.; Albuquerque, J. S. V.; Sales, J.C.; Nogueira, R.E.F.Q., E-mail: hs.pinheiro@metalmat.ufc.br [Universidade Federal do Ceara (UFCE), Fortaleza, CE (Brazil). Centro de Tecnologia. Departamento de Engenharia Metalurgica e de Materiais

    2011-07-01

    During the burning of coal in power plants, various types of waste or by products are generated. These materials have been the subject of several studies. They contain ashes and have many technological applications, such as in the production of various types of ceramic pieces. The objective of this work was to study the feasibility of adding the coal combustion products as filler for ceramics. X-ray fluorescence analysis was used to identify and quantify the proportions of the elements contained in the sample and x-ray diffraction to identify the phases present. The analysis by X-ray diffraction revealed a diffraction pattern of silicon sulfide, calcium silicate and sulfide phases of Aluminium, Potassium and Titanium. X-ray fluorescence analysis showed silica (37.14%), calcium (21.86%), aluminum (14.69%) and sulfur (8.70%). These results show characteristics of materials with potential for incorporation in ceramic bodies, provided that some processing is done to eliminate the sulfur. (author)

  19. Development and characterization of the lead iodide semiconductor detector; Desenvolvimento e caracterizacao do detector semicondutor de iodeto de chumbo

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Icimone Braga de

    2001-07-01

    A methodology for purification and growth of PbI{sub 2} crystal as well as for its characterization as a room temperature radiation detector was developed in this work. Commercial salts were purified using the zone refining method and, for the purified material growth, the Bridgman method was used. To calculate the purification efficiency, studies of the decrease impurities concentrations were made in the salts and in three sections of the materials purified, using the neutron activation analysis technique. The results showed that the impurities segregate preferentially in the ingot final section. A significant decrease of the impurities concentration in function of the purification pass number was observed. The grown crystals presented good crystalline quality according to the results of the X-ray diffraction analysis. To evaluate the crystal as a semiconductor detector, measurements of dark leakage current, resistivity and the response of ({sup 241}Am) alpha particle and ({sup 241}Am, {sup 57}Co, {sup 133}Ba and {sup 137}Cs) gamma rays were carried out. The radiation response is strongly dependent on the crystals purity. The crystals purified with 500 passes exhibited energy resolution of 10% for {sup 241} Am alpha particle and the gamma rays resolution was compatible with the literature. The photosensibility of the PbI{sub 2} crystal found in the wavelength from 400 to 600 nm range suggests an another application at this crystal as a photodetector to be coupled to scintillators. (author)

  20. Carbon supported nanoparticles Pt Ru (Pt Ru/C electrocatalysts) prepared using electron beam irradiation; Preparacao de nanoparticulas de PtRu suportadas em carbono (eletrocatalisadores PtRu/C) utilizando feixe de eletrons

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Dionisio F. da; Oliveira Neto, Almir; Pino, Eddy S.; Linardi, Marcelo; Spinace, Estevam V. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Programa de Celulas a Combustivel], e-mail: espinace@ipen.br, e-mail: dfsilva@ipen.br

    2006-07-01

    Carbon-supported Pt Ru (electrocatalysts PtRu/C nanoparticles) were prepared submitting a water/ethylene glycol mixture containing Pt(IV) and Ru(III) ions and the carbon support to electron beam irradiation. The PtRu/C electrocatalysts were characterized by EDX, XRD and cyclic voltammetry and tested for methanol electro-oxidation aiming fuel cell application. The obtained PtRu/C electrocatalysts were more active for methanol electro-oxidation than the commercial PtRu/C ETEK electrocatalyst at ambient temperature. (author)

  1. Physico-chemical characterization of human recombinant follicle-stimulating hormone (hFSH) and its subunits by reversed-phase high-performance liquid chromatography ( RP-HPLC): comparison with pituitary hFSH reference preparation from 'National Hormone and Pituitary Program' from USA; Caracterizacao fisico-quimica da foliculotropina humana(hFSH) recombinabte e de suas subunidades, por cromatografia liquida de alta eficiencia (HPLC) em fase reversa: comparacao com a preparacao de referencia de hFSH de origem hipofisaria do ''National Hormone and Pituitary Program'' dos EUA

    Energy Technology Data Exchange (ETDEWEB)

    Loureiro, Renan Fernandes

    2006-07-01

    A reversed-phase high-performance liquid chromatography (RP-HPLC) method for the qualitative and quantitative analysis of intact human folliclestimulating hormone (hFSH) was established and validated for accuracy, precision and sensitivity. Human FSH is a dimeric glycoprotein hormone widely used as a diagnostic analyte and as therapeutic product in reproductive medicine. The technique developed preserves the protein integrity, allowing the analysis of the intact heterodimeric form rather than just of its subunits, as it is the case for the majority of the conditions currently employed. This methodology has also been employed for comparing the relative hydrophobicity of pituitary, urinary and two Chinese hamster ovary (CHO)-derived hFSH preparations, as well as of two other related glycoprotein hormones of the anterior pituitary: human thyroid-stimulating hormone (hTSH) and human luteinizing hormone (hLH). The least hydrophobic of the three glycohormones analyzed was hFSH, followed by hTSH and hLH. A significant difference (p<0.005) was observed in t{sub R} between the pituitary and recombinant hFSH preparations, reflecting structural differences in their carbohydrate moieties. Two main isoforms were detected in urinary hFSH, including a form which was significantly different (p<0.005) for the pituitary and recombinant preparations. The linearity of the dose-response curve (r = 0.9965, n = 15) for this RP-HPLC methodology, as well as an inter-assay precision with relative standard deviation less than 4% for the quantification of different hFSH preparations and a sensitivity of the order of 40 ng, were demonstrated. The chromatographic behavior and relative hydrophobicity of the individual subunits of the pituitary and recombinant preparations were also analyzed. Furthermore, the accurate molecular mass of the individual hFSH subunits and of the heterodimer were simultaneously determined by matrix-assisted laser desorption ionization time-of-flight mass spectral analysis (MALDI-TOF-MS). The present methodology represents, in our opinion, an essential tool for characterization and quality control of this hormone that is not yet described in the main pharmacopoeias. (author)

  2. Obtaining and characterization of films of stereo complexes PLLA-PDLA; Obtencao e caracterizacao de filmes de estereocomplexos de PLLA-PDLA

    Energy Technology Data Exchange (ETDEWEB)

    Goncalves, R.P.; Dias, M.L.; Picciani, P.H.S., E-mail: raquelpires@ima.ufrj.b [Universidade Federal do Rio de Janeiro (IMA/UFRJ), RJ (Brazil). Inst. de Macromoleculas Professora Eloisa Mano

    2010-07-01

    Polilactides stereorregulars as poly (L-lactide) (PLLA) has wide application in biomedical and packaging, but despite the structure regular, have relatively low crystallization rate, which limits some applications. The formation of stereocomplexes the mixture of PLLA with poly (D-lactide) (PDLA) has been a strategy used to modify the crystalline structure of these materials, which has an important role in controlling its degradation. In this work we prepared films of PLLA and PDLA alone and their mixtures, aiming to produce stereocomplexes. The PLLA and PDLA were synthesized using different catalysts: tin octoate and calcium methoxide, to investigate the effect of microstructure of polymers in the formation of stereocomplex. The films were obtained by pressing at different temperatures. The materials were characterized by X-ray diffraction and GPC. The results indicate that stereocomplexes with different characteristics are obtained when synthesized with two types of catalysts. (author)

  3. Environmental characterization foundry sands used in sanitary landfills; Caracterizacao ambiental de areias descartadas de fundicao utilizadas na cobertura de residuos em aterros sanitarios

    Energy Technology Data Exchange (ETDEWEB)

    Domingues, L.G.F.; Ferreira, G.C.S.; Pires, M.S.G.; Teixeira, I.; Carnin, R.; Sarro, W.S., E-mail: lucienegferrari@gmail.com [Universidade Estadual de Campinas (UNICAMP), SP (Brazil)

    2016-07-01

    The national solid waste policy recommends reducing solid waste generation and reusing them in different applications. Preliminary studies show that the foundry sand generated from cast metal parts undercut, has excellent applicability in grain size stabilization of soils for geotechnical functions, and therefore, should not be discarded as waste. This study aimed at environmental characterization of two lots of waste foundry sand (WFS), from different industries, to the particle size stabilization of a clayey soil for use in coverage of solid waste in landfills. The methodology included physicochemical characterization tests (grain size, permeability, XRF and heavy metals) and environmental (NBR 10004: 2004, NBR 10005: 2004, NBR 10006: 20004 and acute toxicity with Vibrio fischeri). The results prove the environmental viability of using these lots of WFS as functional material in the composition of landfills. (author)

  4. Synthesis and characterization of semi-IPNs based on PVP and PLLA; Sintese e caracterizacao de semi-IPNs envolvendo os homopolimeros PVP e PLLA

    Energy Technology Data Exchange (ETDEWEB)

    Camilo, A.P.R.; Mano, V., E-mail: mano@ufsj.edu.b [Universidade Federal de Sao Joao del Rei (UFSJ), MG (Brazil). Dept. de Ciencias Naturais; Felisberti, M.I. [Universidade Estadual de Campinas (IQ/UNICAMP), SP (Brazil). Inst. de Quimica

    2010-07-01

    The specific interest in the synthesis of semi-IPNs based on PLLA and PVP homopolymers due to the fact these are biodegradable and biocompatible, which allows us to infer applications in the medical field as sutures, implants, matrices for controlled release of drugs etc. The objective was to prepare a multicomponent material amphiphile in the form of semi-interpenetrating polymer networks, based on poly (L-lactide), PLLA, hydrophobic homopolymer, and poly (vinylpyrrolidone), PVP, hydrophilic component. The preparation of semi-IPN combined the polymerization and crosslinking of N-vinylpyrrolidone in the presence of poly (L-lactide). The products were characterized by spectroscopic and thermal methods. (author)

  5. Surface characterization of alloy Ti-6Al-7Nb treated plasma; Caracterizacao superficial de ligas de Ti-6Al-7Nb tratadas a plasma

    Energy Technology Data Exchange (ETDEWEB)

    Moura, J.K.L.; Macedo, H.R.A.; Brito, E.M.; Brandim, A.S., E-mail: jessika.kaline@hotmail.com [Instituto Federal do Piaui (PPGEM/IFPI), Teresina, PI (Brazil)

    2014-07-01

    Plasma surface modifications are subject of numerous studies to improve the quality of a given material. Titanium and its alloys are widely used in biomedical applications and plasma treatment technique is increasingly used to improve the surface properties thereof. The research have a objective in the comparative analysis of the change in microstructure of Ti-6Al-7Nb alloys after treatment of plasma nitriding. The technical are: nitriding with cathode cage (NGC) and planar discharge. The characterization was obtained by MEV (Scanning Electronic Microscope) and hardness. The results was compared about the better surface modification that meets future prospects of the biocompatibility of the alloy.(author)

  6. Physico-chemical characterization of biodiesel from pests attacked corn oil; Caracterizacao fisico-quimica do biodiesel de oleo de milho danificado por pragas

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, Fabia M.; Correa, Paulo C.; Martins, Marcio A.; Santos, Silmara B.; Damian, Amanda D. [Universidade Federal de Vicosa (UFV), MG (Brazil)], Emails: copace@ufv.br, aredes@ufv.br, syllmara@vicosa.ufv.br

    2009-07-01

    The biodiesel is a renewable energy source alternative to fossil fuels. The biodiesel synthesis can be made by many types of triglycerides transesterification, it is possible to use this biofuel in vehicles if it has the quality required from Agencia Nacional de Petroleo, Gas Natural e Biocombustiveis (ANP). Searching an application for pests attacked corn, there is feasibility technical for the biodiesel production from this corn oil. The biodiesel synthesis was made through ethyl transesterification process with alkaline catalyst using ethanol. The biodiesel physical-chemical characterization was performed using ANP methods. (author)

  7. Extraction and characterization of galactomannan extracted from Prosopis juliflora seeds; Extracao e caracterizacao de galactomanana extraida a partir de sementes de Prosopis juliflora

    Energy Technology Data Exchange (ETDEWEB)

    Rodrigues, Delane da C.; Cunha, Arcelina P.; Oliveira, Williara Q. de; Gallao, Maria Izabel, E-mail: izagalao@gmail.com [Rede Nordeste de Biotecnologia (RENORBIO), Fortaleza, CE (Brazil). Centro de Ciencia; Azeredo, Henriette M.C. de [EMBRAPA Agroindustria Tropical, Fortaleza, CE (Brazil)

    2013-07-01

    Different seeds are rich in polysaccharides, which are widely used in research and in industry. The objective was to extract galactomannan from mesquite seeds (Prosopis juliflora) and evaluate their chemical properties for future application in edible films. To test the feasibility of using the polysaccharide, the yield was obtained and the material analyzed by Thermal Analysis (TGA-Thermogravimetric Analysis and Calorimetry Differential Scanning-DSC), Spectroscopy Infrared Region Fourier Transform (FTIR) and Nuclear Magnetic Resonance (NMR). According to the results, the galactomannan was equivalent with the polysaccharides extracted from other sources except for the low yield (6.6%). (author)

  8. Extraction and characterization of galactomannan extracted from Prosopis juliflora seeds; Extracao e caracterizacao de galactomanana extraida a partir de sementes de Prosopis juliflora

    Energy Technology Data Exchange (ETDEWEB)

    Rodrigues, Delane da C.; Cunha, Arcelina P.; Oliveira, Williara Q. de; Gallao, Maria Izabel, E-mail: izagalao@gmail.com [Rede Nordeste de Biotecnologia (RENORBIO), Forteleza, CE (Brazil). Centro de Ciencia; Universidade Federal do Ceara (UFC), Fortalea, CE (Brazil); Azeredo, Henriette M. C de [EMBRAPA Agroindustria Tropical, Fortaleza, CE (Brazil)

    2015-07-01

    Different seeds are rich in polysaccharides, which are widely used in research and in industry. The objective was to extract galactomannan from mesquite seeds (Prosopis juliflora) and evaluate their chemical properties for future application in edible films. To test the feasibility of using the polysaccharide, the yield was obtained and the material analyzed by Thermal Analysis (TGA-Thermogravimetric Analysis and Calorimetry Differential Scanning-DSC), Spectroscopy Infrared Region Fourier Transform (FTIR) and Nuclear Magnetic Resonance (NMR). According to the results, the galactomannan was equivalent with the polysaccharides extracted from other sources except for the low yield (6.6%). (author)

  9. Chemical characterization of polymeric surge arresters and insulators used in high voltage lines; Caracterizacao quimica de para-raios e isoladores utilizados em linhas de alta tensao

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira Junior, Joao B. de; Castro Junior, Joao B. de; Silva, Maria Elisa S.R. e; Freitas, Roberto F.S.; Sousa, Ricardo G. de [Lab. de Ciencia e Tecnologia de Polimeros, Dept. de Engenharia Quimica da EE.UFMG, Belo Horizonte, MG (Brazil); Souza, Breno P.G. de [CEMIG Distribuicao S/A, Belo Horizonte, MG (Brazil)], e-mail: bpgsouza@gmail.com

    2011-07-01

    In the last two decades, traditional porcelain and glass surge arresters and insulators, used in the electrical system, have been replaced by polymeric materials. For this type of application it is recommended that these devices have a high resistance to environmental stresses and impacts without suffering degradation process. Considering the environmental conditions these polymers are exposed to, when used for this purpose, studies of their chemical composition are needed. In this work, polymeric materials present in surge arresters and insulators used in electrical system were chemically characterized by Fourier Transform Infrared Spectroscopy (FTIR). FTIR analysis showed that the samples tested are made of poly(dimethylsiloxane) - PDMS (silicone) and additives such as alumina trihydrated [Al (OH)3] and calcium carbonate. (author)

  10. Obtain and characterization of chitosan / propranolol microparticles by spray drying; Obtencao e caracterizacao de microparticulas de quitosana / propranolol por spray drying

    Energy Technology Data Exchange (ETDEWEB)

    Nascimento, Ednaldo G. do; Silva Junior, Arnobio A. da, E-mail: ednaldogn@yahoo.com.br [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil); Santos, Katia S.C.R. dos [Universidade Federal do Amazonas (UFAM), Manaus, AM (brazil)

    2015-07-01

    The study investigated the application of chitosan microparticles as carriers into hard gelatin capsule containing propranolol, evaluating the variability of the molecular weight and the chitosan particles by spray drying. The formulations were characterized by average weight, dosing unit dose uniformity and dissolution profile according to the pharmacopoeia. While the microparticles were characterized by Fourier transformed infrared spectroscopy, scanning electron microscopy and X-ray diffraction. The results showed that chitosan microparticles obtained without the drug and then physically mixed with propranolol promoted a modified release 85% of the drug after 5 hours. While, chitosan microparticles sprayed with propranolol released only 55% at 5 hours is presented both as a modified release system. Samples of dried chitosan showed up amorphous and homogeneous and spherical morphology. (author)

  11. Characteristics of the radiochromic film Gafchromictm EBT3 model for use in brachytherapy; Caracterizacao do filme radiocromico Gafchromictm modelo EBT3 para uso em braquiterapia

    Energy Technology Data Exchange (ETDEWEB)

    Luvizotto, Jessica

    2015-07-01

    Brachytherapy is a radiotherapy treatment modality using radioactive sealed sources within walking distance of the tumor, reducing the risk of applying an unwanted dose to adjacent healthy tissues. For brachytherapy is reliable, it is necessary to establish a dosimetric practices program aimed at determining the optimal dose of radiation for this radiotherapy practice. This paper presents the application of two methodologies for the dosimetry using radiochromic films. Experimental measurements were performed with EBT3 films in phantoms consisting of homogeneous and heterogeneous material (lung, bone and soft tissue) built especially for dose measurements in brachytherapy. The processing and analysis of the resulting images of the experimental procedure were performed with ImageJ software and MATLAB. The results were evaluated from comparisons dose of experimental measurements and simulations obtained by the Monte Carlo method. (author)

  12. Synthesis and characterization of NiO nanoparticles by Pechini method; Sintese e caracterizacao de nanoparticulas de NiO pelo metodo Pechini

    Energy Technology Data Exchange (ETDEWEB)

    Nascimento, A.; Ribeiro, M.A.; Costa, A.C.F.M.; Gama, L. [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Dept. de Engenharia de Materiais; Bernardi, M.I.B. [Universidade de Sao Paulo (IFSC/USP), Sao Carlos, SP (Brazil). Inst. de Fisica

    2009-07-01

    In recent years, ultrafine magnetic particles of NiO have attracting the attention because of its unknown behavior, enormous scientific potential and technological application. Some of its more important properties are accented magnetic moments, double dynamic exchange, quantization of wave of spin and etc. In this context, this work has for objective to synthesize and to characterize nanoparticles of NiO for the Pechini method. The powder was analyzed by X-rays diffraction. The results of scanning electron microscopy, adsorption of nitrogen. The analysis of X-rays diffraction of the sample showed single-phase peaks of NiO, with crystallite size close to 38 nm. The surface area was 6.44 m{sup 2}/g. The image from scanning electron microscopy shows soft homogeneous agglomerates. The Pechini synthesis was efficient in the production of powders of NiO nano metrics and single-phase. (author)

  13. Synthesis and characterization on titanium dioxide prepared by precipitation and hydrothermal treatment; Sintese e caracterizacao de dioxido de titanio preparado por precipitacao e tratamento hidrotermico

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Andre V.P. dos; Yoshito, Walter K.; Lazar, Dolores R.R.; Ussui, Valter, E-mail: vussui@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2012-07-01

    Surface properties of titanium dioxide (titania) are outstanding among ceramic materials and enables uses as catalysts, photoelectrochemical devices, solar cells and others. In many of these applications, it is necessary to keep the anatase phase, that is stable only in low temperatures (<400 deg C). In the present work, the influence of hydrothermal treatment on physical characteristics and crystal structure of titania powders synthesized by precipitation was investigated. Characterizations of obtained powders were carried out by X-ray diffraction, surface area analysis by N2 gas sorption (BET) and microstructure of powders and ceramics were analyzed by scanning electron microscopy. As prepared powders were formed as cylindrical pellets by uniaxial pressing and sintered at 1500 deg C for 01 hour. Results showed that anatase phase without formation of rutile phase can be formed in hydrothermally treated samples . Rutile phase is predominant in calcined and/or sintered samples (author)

  14. Synthesis and characterization of poly(styrene-co-methyl methacrylate); Sintese e caracterizacao do poli(estireno-co-metacrilato de metila)

    Energy Technology Data Exchange (ETDEWEB)

    Augustinho, Tiago R.; Abarca, Silvia A.C.; Machado, Ricardo A.F. [Departamento de Engenharia Quimica e Alimentos - Universidade Federal de Santa Catarina - UFSC, Florianopolis, SC (Brazil)

    2011-07-01

    Polystyrene (PS) is nowadays commonly used due its advantages over competitors. PS presents a lower cost when compared with Acrylonitrile Butadiene Styrene (ABS) and with Polyethylene Tere-phthalate (PET), and can be easier processed than polypropylene (PP). At expandable form (EPS), can be used as projective equipment, thermal insulation, floating boards, refrigerators, isothermal, and low cost applications such as packaging and disposable material. Searching for more resistant materials and with a low cost, researches with copolymers materials are being developed. In this study, copolymerization reactions were carried out by suspension polymerization using monomers styrene and methyl methacrylate (MMA) with styrene. Styrene was in the highest percentage in relation to the MMA. The MMA was selected because is a monomer that presents a higher resistance than PS. The copolymerization was confirmed by performing infrared spectroscopy (IR), nuclear magnetic resonance of hydrogen (RMN{sup 1}H), differential scanning calorimetry (DSC) and thermogravimetry (TGA). (author)

  15. Physicochemical characterization of ceramics from Sao Paulo II archaeological site; Caracterizacao fisico-quimica da ceramica do sitio arqueologico Sao Paulo II

    Energy Technology Data Exchange (ETDEWEB)

    Ribeiro, Rogerio Baria

    2013-08-01

    Archaeometry is a consolidated field with a wide application of nuclear analytical techniques for the characterization, protection, and restoration of archaeological pieces. This project aimed at studying the elementary chemical composition of 70 ceramic fragments samples from Sao Paulo II archaeological site, located along the Solimoes River channel, next to Coari city, in Brazilian Amazon. The characterization of samples was performed by neutron activation analysis (NAA). By the determination of 24 elements in the ceramic fragments ( Ce, Co, Cr, Cs, Eu, Fe, Hf, K, La, Lu, Na, Nd, Sb, Sm. Rb, Se, Ta, Tb, Th, U, Yb and Zn), it was possible to define groups of samples regarding the similarity/dissimilarity in elementary chemical composition. For such a task, the multivariate statistical methods employed were cluster analysis (C A), principal component analysis (PCA) and discriminant analysis (DA). Afterwards, seven ceramic fragments were selected based on the groups previously established, for the characterization of the site temporal horizon. Those ceramic fragments were analyzed by thermoluminescence (TL) and EPR for dating purposes. The firing temperatures were determined by electron paramagnetic resonance (EPR) technique, in order to infer about some aspects of the ceramic manufacture employed by the ancient peoples that lived in Sao Paulo 11. By the results obtained in this study, it was possible to identify the quantity of clay sources employed by the ceramists and the age of the ceramic pieces. Therefore, the results of this research may contribute to the study on the occupation dynamics in the pre-colonial Brazilian Amazon. (author)

  16. Preparation and characterization of corn reinforced polymer sheet of fibers; Obtencao e caracterizacao de polimero reforcado com fibras da folha de milho

    Energy Technology Data Exchange (ETDEWEB)

    Moreira, Tatiana Martinez; Seo, Emilia Satoshi Miyamaru, E-mail: tatianaltda@hotmail.com, E-mail: esmiyseo@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2016-10-15

    There is a global trend in seeking plant fibers to replace the synthetic fibers to obtain reinforced composites aimed at the use of renewable resources. In this context, this paper aims to develop the process of preparing maize leaf fibers, characterizing them and adapting them for applications in the construction industry and develop a reinforced polymer composite with these fibers. Corn leaves were dried in environmental temperature, treated by mercerizing, then neutralized with acid solution and washed in running water. The characterization of the corn leaf fibers was carried out by X-ray diffraction, X-ray fluorescence, scanning electron microscopy, specific surface area, thermogravimetry and specific mass. The mercerizing treatment was effective, because the maize fibers have characteristics similar to synthetic fibers, leading to a possibility of new technological uses. The polymeric composite material was developed by extrusion processes and injection and tested for tensile testing, differential scanning calorimetry and scanning electron microscopy, thus reused an organic waste that would be disposed of by inserting it in a technological process, contributing to the research and development of new polymeric materials as well as to reduce waste discarded as scrap. (author)

  17. Characterization of tissue-equivalent materials for use in construction of physical phantoms; Caracterizacao de materiais tecido-equivalentes para uso em construcao de fantomas fisicos

    Energy Technology Data Exchange (ETDEWEB)

    Souza, Edvan V. de, E-mail: edvanmsn@hotmail.com [Instituto Federal de Educacao, Ciencia e Tecnologia de Pernambuco (IFFPE), Recife, PE (Brazil); Oliveira, Alex C.H. de, E-mail: oliveira_ach@yahoo.com [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil); Vieira, Jose W., E-mail: jose.wilson59@uol.com.br [Escola Politecnica de Pernambuco (UPE), Recife, PE (Brazil); Lima, Fernando R.A., E-mail: falima@cenen.gov.br [Centro Regional de Ciencias Nucleares (CRCN-NE/CNEN-PE), Recife, PE (Brazil)

    2013-07-01

    Phantoms are physical or computational models used to simulate the transport of ionizing radiation, their interactions with human body tissues and evaluate the deposition of energy. Depending on the application, you can build phantoms of various types and features. The physical phantoms are made of materials with behavior similar to human tissues exposed to ionizing radiation, the so-called tissue-equivalent materials. The characterization of various tissue-equivalent materials is important for the choice of materials to be used is appropriate, seeking a better cost-benefit ratio. The main objective of this work is to produce tables containing the main characteristics of tissue-equivalent materials. These tables were produced in Microsoft Office Excel. Among the main features of tissue-equivalent materials that were added to the tables, are density, chemical composition, physical state, chemical stability and solubility. The main importance of this work is to contribute to the construction of high-quality physical phantoms and avoid the waste of materials.

  18. Characterization of taquara-lixa (Merostachys skvortzovii Sendulsky) fibers for use in polymer composites; Caracterizacao de fibras de taquara-lixa (Merostachys skvortzovii Sendulsky) utilizaveis em compositos polimericos

    Energy Technology Data Exchange (ETDEWEB)

    Borges Neto, Camilo; Flores-Sahagun, Thais H.S.; Andrade, Alan S. de; Mazzaro, Irineu, E-mail: cyborg@ufpr.br [Universidade Federal do Parana (UFPR), Curitiba, PR (Brazil)

    2015-07-01

    Characterization of untreated or alkali-treated 'taquara-lixa' (Merostachys skvortzovii Sendulsky ), a low cost Brazilian bamboo fiber, was performed by determining their chemical composition (moisture, ash, lignin and extractives contents), solubility in hot or cold water, pH values and crystallinity index. Thermal analysis showed that fibers begin to degrade at 250 deg C. Samples of taquara-lixa/epoxy resin composites were prepared with 56% w/w aligned long fibers (280 mm) and with 54% (w/w) dispersed short fibers (25 mm) and a sandwich-beam sample shaped in three layers was prepared with two outer long fiber composite layers separated by a thicker layer of the short fiber material. Composites were characterized by x-ray diffraction patterns, water and moisture absorption and flexural tests. Elasticity and shear modulus of composites (15500 MPa and 932 MPa/6800 MPa and 1042 MPa for long and short composites, respectively) indicated that these materials can be used for structural applications, with the advantage of low water (8.4%) and low moisture (2.4-2.8%) absorption. (author)

  19. Development and characterization of special ionization chambers for computed tomography beams; Desenvolvimento e caracterizacao de camaras de ionizacao especiais para feixes de tomografia computadorizada

    Energy Technology Data Exchange (ETDEWEB)

    Castro, Maysa Costa de

    2016-10-01

    The use of computed tomography (CT) for imaging procedures is growing due to advances in the CT equipment technology, because they allow the obtention of images with better resolution than through other techniques. Therefore, they are responsible for increasing the dose radiation of patients during the procedure. This fact led to a greater concern about the doses received by patients who undergo this type of examination. To perform the dosimetry in CT beams, the most widely used instrument is the pencil type ionization chamber, because this dosimeter has a uniform response to the incident radiation beam for all angles. The conventional ionization chamber, which is available on the market, has a sensitive volume length of 10 cm; however, some studies have shown that this dosimeter has underestimated the dose values. Therefore, in this study two ionization chambers with sensitive volume lengths of 10 cm and 30 cm, making use of low cost national materials, were developed at the Calibration Laboratory of Instruments (LCI-IPEN/CNEN). The characterization of these chambers was performed, and the results were obtained within the international recommended limits. As an application, the developed ionization chambers and a commercial chamber were tested in a clinical tomograph. The developed ionization chambers were analyzed in a complete way for their possible uses. (author)

  20. Methodological development and characterization of welded joints in Poly (vinylidene fluoride) (PVDF); Desenvolvimento metodologico e caracterizacao de juntas soldadas de PVDF

    Energy Technology Data Exchange (ETDEWEB)

    Cedrola, S.M.L.; Costa, M.F. da; Pasqualino, I.P., E-mail: samanta@metalmat.ufrj.b [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil)

    2010-07-01

    Pipelines are of great concern in the transport sector of oil and gas industries, mainly due to the natural internal aging process caused by contact with the different transported fluids. Installation of polymeric pipes called liners is a good option for rehabilitation of long segments of deteriorated pipelines. Among the potential materials for such application is Poly (vinylidene fluoride) (PVDF). Meanwhile the installation process cannot be carried out in one single step and the polymeric pipe must be cut in sections that are welded during the installation process. In this research welding methodology was studied aiming to optimize welding conditions and the mechanical properties of the joined materials. The first step was processing the PVDF via compression molding on different conditions. Then, the sample was cut and butt-welded. Welding parameters such as, time control, temperature and contact pressure were studied. Afterwards, the stress-strain properties of the welded material was evaluated and physical characterization was carried by x-ray diffraction (DRX). (author)

  1. Biochemical and pharmacological characterization of irradiated crotamine by gamma rays of {sup 60}Co; Caracterizacao bioquimica e farmacologica da crotamina irradiada por raios gama de {sup 60}Co

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Karina Corleto

    2014-07-01

    The serum production in Brazil, the only effective treatment in cases of snakebites, uses horses that although large size, have reduced l lifespan compared with horses not immunized. Ionizing radiation has been shown as an excellent tool in reducing the toxicity of venoms and toxins isolated, and promote the achievement of better immunogens for serum production, and contributing to the welfare of serum-producing animals. It is known, however, that the effects of ionizing radiation on protein are characterized by various chemical modifications, such as fragmentation, cross-linking due to aggregation and oxidation products generated by water radiolysis. However, the action of gamma radiation on toxins is not yet fully understood structurally and pharmacologically, a fact that prevents the application of this methodology in the serum production process. So we proposed in this paper the characterization of crotamine, an important protein from the venom of Crotalus durissus terrificus species, irradiated with {sup 60}Co gamma rays. After isolating the toxin by chromatographic techniques and testing to prove the obtaining of pure crotamine, it was irradiated with gamma rays and subjected to structural analysis, Fluorescence and Circular Dichroism. Using high hydrostatic pressure tests were also conducted in order to verify that the conformational changes caused by radiation suffer modifications under high pressures. From the pharmacological point of view, muscle contraction tests were conducted with the objective of limiting the action of crotamine in smooth muscle as well as the change in the action of toxin caused structural changes to the front. Analysis of Circular Dichroism and Fluorescence showed changes in structural conformation of crotamine when subjected to gamma radiation and that such changes possibly occurring in the secondary and tertiary structure of the protein. The observed in pharmacological tests showed that the irradiated crotamine was less effective

  2. Silica-gel structural characterization during the initial phases of gelation and drying; Caracterizacao estrutural de geis de silica durante as etapas iniciais de gelacao e secagem

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira, Max Passos

    1996-12-31

    For centuries, glasses and ceramics have been made via melting or solid state reactions at temperatures above 100 deg C. The sol-gel process offers new approaches to the synthesis of glasses and ceramics, combining control of composition and structure at the molecular level with the ability to shape materials in bulk, powder, fiber and thin-film forms. The growth of sol-gel technology research is due to the many unique features of that class of materials. Major applications include optical elements and integrated optical devices, ceramic filters, membranes, supercondutors, magnetic, catalytic and manostructured materials to antioxidant, anticorrosion coatings and composite and biomedical materials. In this work a variety of techniques like spectroscopy, Raman spectroscopy, ultraviolet-visible spectroscopy, light scattering nuclear magnetic resonance, X ray diffraction and nitrogen adsorption have been employed to investigate the initial phase of the sol-gel transition of gamma ray irradiated tetramethoxysilane (TMOS) solutions and non-irradiated TMOS solution and to get information about the structure of the silica gels obtained under different gelation conditions. Typically the tetramethoxysilane solutions were prepared using a molar ratio of TMOS to demineralized water of 1 to 16. Some experiments were made under catalysed conditions. The mixing was carried out at room temperature. The turbidity and light scattering experiments on the polycondensation of tetramethoxysilane show that exists no drastic difference in the gelling time of a gamma ray irradiated and a non-irradiated TMOS+H{sub 2}O (1+16 M) solution. In the absence of a catalyst, the gelling time for both reactions occurs in about 3.30 h. When HNO{sub 3} (o.03 M) was used, the gelling time observed was 3 days. Raman and ultraviolet-visible spectroscopy show no drastic difference during the initial phase at the sol-gel transition under ambient temperature/pressure and under gamma radiation. The gels

  3. Characterization of silicates and calcium carbonates applied to high-dose dosimetry; Caracterizacao de silicatos e carbonatos de calcio aplicados a dosimetria de doses altas

    Energy Technology Data Exchange (ETDEWEB)

    Vila, Gustavo Barreto

    2012-07-01

    The predominant isomorphous form in the biominerals studied in this work (oyster shell, coral, mother of pearl and shell) was aragonite. The appearance of the calcite phase occurred at 500 deg C at a heating rate of 10 deg {sup C}/s for all samples except for the coral sample, which was 400 deg C, independent of the heating rate. The most abundant element in the biominerals samples was Ca in the CaO form, and in the silicates (tremolite, diopside and rhodonite) Si in the SiO form. The most common trace element observed in the biominerals samples was Fe. The analyses of electron paramagnetic resonance showed lines of Mn{sup 2+} in the coral and mother-of-pearl samples before irradiation. In the case of the irradiated samples, the defects found were CO{sub 2}{sup -}, CO{sub 3}{sup 3-}, CO{sub 3}{sup -} and SO{sub 2}{sup -}, in the g range between 2.0010 and 2.0062. In the analyses by optical absorption of biominerals, transitions due to the presence of Mn in the samples were found. A thermoluminescent (TL) peak at approximately 140 deg C was found for the biominerals and at 180 deg C for silicates, which intensity depends directly on the dose. For samples exposed to different types of radiation, the TL peak occurred at lower temperatures. From the dose-response curves obtained for these materials, it was possible to determine a linear range for which their application in high dose dosimetry becomes possible. Taking into account the radiation type, among biominerals and silicates, the lowest detectable dose (40mGy) to gamma radiation was achieved for oyster shell samples using the measuring technique of optically stimulated luminescence (OSL). Using beta radiation, for diopside and tremolite samples the lowest detectable dose of 60mGy was obtained. For all samples, using the TL, OSL and thermally stimulated exoelectron emission (TSEE) techniques in alpha, beta and gamma radiation beans a good response reproducibility was obtained. Therefore, the samples characterized

  4. Technological characterization of new clay deposits in the south region of Amapa, Brazil aiming applications in the ceramic industry; Caracterizacao tecnologica de novos depositos de argilas da regiao sul do Amapa visando aplicacoes na industriav ceramica

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Adriano Lima da; Luna, Carlos Bruno Barreto; Chaves, Alexsandra Cristina; Neves, Gelmires de Araujo, E-mail: adrianolimadasilva@hotmail.com, E-mail: brunobarretodemaufcg@hotmail.com [Universidade Federal de Campina Grande (UAEMa/CCT/UFCG), PB (Brazil). Unidade Academica de Engenharia de Materiais

    2017-01-15

    The objective of the present work was to characterize two new Clay deposits (A and B) from the south region of Amapa state, aiming to establish their adequate uses as ceramic raw materials and to promote the potential of the ceramic industry in the region. Were prepared specimens by uniaxial pressing, being applied a two phase pressing of 13,4 MPa and 20 MPa, respectively. The samples were dried in an oven at 110 deg C, and submitted to burning at 850, 1000 and 1200 deg C. Were determined linear firing shrinkage, water absorption, apparent porosity and modulus of flexural modulus of rupture, as well as mineralogical evolution after burning. Finishing, the microstructure of the sintered clay at 1200 deg C was evaluated in a scanning electron microscope. The results showed that the clay A presented a better mechanical development, having a red coloration and, therefore, potential to the red ceramic industry. On the other hand, the clay B presented a light color, due to a low content of iron oxide and, therefore, having potential as refractory raw material. In general, one clay is suitable to be used in white ceramic and the other in red ceramic. (author)

  5. Microstructural development and characterization of lanthanum chromite-based ceramics to application in solid oxide fuel cells; Desenvolvimento microestrutural e caracterizacao de ceramicas a base de cromita de lantanio para aplicacao em celulas a combustivel de oxido solido

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, R.N.; Furtado, J.G. de M.; Soares, C.M.; Serra, E.T. [Centro de Pesquisas de Energia Eletrica (CEPEL), Rio de Janeiro, RJ (Brazil)], e-mail: rnunes@cepel.br

    2006-07-01

    This work has for objective to investigate and to characterize the microstructural development of lanthanum chromite-based ceramics (LaCrO{sub 3}) doped with earth alkaline metals, correlating the microstructural parameters (mainly the densification level) and processing parameters with the electrothermal properties reached. Lanthanum chromite-based ceramic systems doped with earth-alkaline metals (Ca, Mg and Sr) had been produced from respective metallic nitrates by solid state reactions process. The phase compositions were evaluated by X-ray diffraction and the densification level by Archimedes method. The microstructural characterization was effected by scanning electron microscopy, energy dispersive X-ray spectroscopy and thermal analysis techniques. Electrical tests were used to evaluate the electrical conductivity of the studied ceramics. The obtained results corroborate the literature comments concerning the difficulty of lanthanum chromite-based ceramics with high densification level and evidence the great influence of the nature of the dopants on the sintering mechanism and the microstructural and electric characteristics of the produced ceramics. The best ones results, in terms of densification and electrical conductivity, had been gotten through multiple doping with calcium and strontium, and in sintering temperature conditions lower that the normally considered to pure or monodoped lanthanum chromite-based ceramics. (author)

  6. Characterization of radiation qualities used for the determination of characteristic in CT application according to IEC 61267:2005;Caracterizacao das qualidades de radiacao usadas na determinacao das caracteristicas em aplicacoes de CT de acordo com a IEC 61267: 2005

    Energy Technology Data Exchange (ETDEWEB)

    Dias, Daniel M.; Silva Junior, Iremar A. da; Potiens, Maria da Penha A. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2009-07-01

    The purpose of this study was to establish the standard RQT radiation qualities which represent simulations of the unattenuated beam used in Computed Tomography (CT). Thus, to avoiding excessive efforts for establishing a radiation quality by means of the spectral distribution of the photon fluence, the characterization of these standard radiation qualities was expressed in terms of the X-ray tube voltage, first and second half-value layer (HVL). To establishing the standard radiation beam, according to the IEC 61267 and the TRS 457 was measured first of all the correct values of the X ray tube voltages in terms of Practical Peak Voltage. The standard radiation qualities RQT were produced using the same set up mounted for the RQR qualities which had been early established, and for simulating the patient in order to achieve the standard RQT series, suitable thicknesses of layers of copper were used to obtain the values of the first HVL according to IEC 61267. (author)

  7. Polymeric membranes obtained from S-PEEK for application in PEM fuel cells; Caracterizacao de membranas polimericas obtidas a partir dos S-PEEK para aplicacao em celulas combustiveis do tipo PEM

    Energy Technology Data Exchange (ETDEWEB)

    Barreto, Ednardo G.; Fiuza, Raildo A.; Catao, Ronei S.; Jose, Nadia M.; Boaventura, Jaime S. [Universidade Federal da Bahia (UFBA), Salvador, BA (Brazil). Inst. de Quimica], e-mail: ednardobarreto@yahoo.com.br, e-mail: raildofiuza@gmail.com, e-mail: roneicatao@ig.com.br, e-mail: nadia@ufba.br, e-mail: bventura@ufba.br; Pepe, Yuri [Universidade Federal da Bahia (UFBA), Salvador, BA (Brazil). Inst. de Fisica

    2007-07-01

    This work had the objective to develop and to characterize S-PEEK membranes (sulfonated poly ether ether ketone) through chemical and electrochemical analyses. Conductivity test in function of the frequency and tension had been carried through; as well as, the open circuit tension of a fuel cell using the S-PEEK as electrolyte. Additional tests included TGA (Thermogravimetric Analysis), water absorption test, DSC (Differential Scanning Calorimetry), as tools to characterize conducting, thermal and mechanical proprieties of polymeric membrane. (author)

  8. Characterization of commercial ceramic adsorbents and their application on naphthenic acids removal of petroleum distillates; Caracterizacao de adsorventes ceramicos comerciais e sua aplicacao na remocao de acidos naftenicos de destilados de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Silva, J.P.; Senna, L.F. de; Lago, D.C.B. do; Silva Junior, P.F. da; Figueiredo, M.A.G. de; Dias, E.G. [Universidade do Estado do Rio de Janeiro (UERJ), RJ (Brazil)], e-mail: julia_psi@yahoo.com.br; Chiaro, S.S.X. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas (CENPES)

    2006-07-01

    One denominates 'naphthenic acids' to the mixture of carboxylic acids that is present in petroleum oil, and is directly responsible for its acidity and corrosiveness in liquid phase during the refine process. These acids are also presents in distilled fraction of petroleum, causing several problems in final products quality. A possible way to remove them from petroleum distilled fractions is the adsorption in porous materials. However, the published results indicate that ion exchange resins would be the best adsorbents for this process, which would probably increase its cost. In this work, two commercial adsorbents (clay and activated alumina) were characterized by a set of physical-chemistry techniques and evaluated concerning their capacity of removing naphthenic acids from a light petroleum fraction. It was also verified the influence of a previous thermal treatment to the adsorption in their physical-chemistry characteristics and its properties. (author)

  9. Optimization of preparation, labelling and quality control procedures of {sup 99m}Tc-glucarate for the diagnosis of acute myocardial infarction; Otimizacao dos procedimentos de preparacao, marcacao e controle de qualidade do glucarato-{sup 99m}Tc para diagnostico do infarto agudo do miocardio

    Energy Technology Data Exchange (ETDEWEB)

    Camargo, Ana Claudia

    2007-07-01

    Cardiovascular diseases account for the main causes of morbidity and mortality among the adult population. Despite the advances of preventive medicine, acute myocardial infarction continues to be frequent and the difficulty of the differential diagnosis is an additional cause of fatal events. Its diagnosis is based on the triad: typical chest pain, alterations in the electrocardiogram and elevation of serum cardiac enzymes. However, many patients evolve without the complete syndrome. Therefore the development of non-invasive assays for the early detection of damaged myocardium is of extreme importance. {sup 99m}Tc-glucarate is a radiopharmaceutical of great interest for application in Nuclear Medicine, because it is referred as a potential marker of necrotic tissues in the early phase of an acute coronary event. This presentation describes the optimization of preparation, lyophilization and labelling as well as quality control procedures of {sup 99m}Tc-glucarate, based on former studies published in the literature. Radiochemical purity was evaluated by the ascending paper chromatography technique. Labelling efficiency as a function respectively of time of reaction, volume and activity of {sup 99m}TcO4- was consistently higher than 97%. The lyophilized kit was stable during 12 months of storage. Biodistribution in healthy Swiss mice showed rapid blood clearance, renal excretion and low uptake by organs adjacent to the heart. Scintigraphic studies of injected Wistar rats confirmed the results of the biodistribution obtained by direct organ counting. Scintigraphies of infarcted female rats proved the sensitivity of the method. (author)

  10. Characterization of gadolinia-doped ceria with manganese addition synthesized by the cation complexation technique; Caracterizacao de ceria-gadolinia e ceria-gadolinia-manganes sintetizados pelo metodo de complexacao de cations

    Energy Technology Data Exchange (ETDEWEB)

    Yang, J.D.; Muccillo, R.; Muccillo, E.N.S., E-mail: enavarro@usp.b [Instituto de Pesquisas Energeticas e Nucleares (CCTM/IPEN/CNEN-SP), Sao Paulo, SP (Brazil). Centro de Ciencia e Tecnologia de Materiais; Rocha, R.A. [Universidade Federal do ABC (CEMCSA/UFABC), Santo Andre, SP (Brazil). Centro de Engenharia, Modelagem e Ciencias Sociais Aplicadas

    2010-07-01

    Ceria-based compounds may be used for several technological applications like catalysts, grinding media and materials for electrolyte and electrodes in solid oxide fuel cells. For most of these applications fine powders are required. In this work, nanostructured ceria powders containing 20 mol % gadolinia with and without manganese addition were synthesized by the cation complexation technique. The prepared powders were calcined at 600 deg C for thermal decomposition of the metal citrate precursors. Results of X-ray diffraction, scanning electron microscopy and specific surface area evidenced the role of manganese on physical characteristics of the nanostructured materials. The cation complexation technique revealed to be a promising method for obtaining nanostructured powders with high yield and suitable physical properties for several technological applications. (author)

  11. Preparation of organoclays in matrix elastomer; Preparacao de argilas organofilicas em matriz de elastomero

    Energy Technology Data Exchange (ETDEWEB)

    Gonzales-Fernandes, M.; Valenzuela-Diaz, F.R.; Wiebeck, H., E-mail: mgf@usp.br [Universidade de Sao Paulo (PMT/USP), Sao Paulo, SP (Brazil). Escola Politecnica; Esper, F.J. [Faculdades Metropolitanas Unidas (FISP/FMU), Itapevi, SP (Brazil); Martin-Cortes, G.R. [Centro Universitario Estacio Radial de Sao Paulo (UniRadial), SP (Brazil)

    2014-07-01

    Natural rubber nanocomposite / bentonite modified by sodification chocolate B and treated with quaternary ammonium salt was prepared. The clay in its natural state after sodification and after quaternization was characterized by XRD, IR, and stereoscopic microscope and SEM was measured its ability to swell in many organic solvents. The plates obtained after curing, measures have had their mechanical properties and analyzed by XRD. The nanocomposites showed improvement in their mechanical properties compared to boards without the addition of clay. (author)

  12. Mullite preparation from natural raw materials; Preparacao de mulita a partir de materias-primas naturais

    Energy Technology Data Exchange (ETDEWEB)

    Sales, Lindemberg Felismino; Almeida Filho, Humberto Dias de; Goncalves, Joao de Freitas; Macedo, Daniel Araujo de [Universidade Federal da Paraiba (UFPB), Joao Pessoa, PB (Brazil). Departamento de Engenharia de Materiais

    2016-07-01

    The mullite (3Al2O3.2SiO2) has emerged as one of the most important refractory ceramics today. In this work, kaolin, and mixtures of coffee husk ash, a residue arising from the burning of coffee husks were studied in order to obtain the mullite ceramic base. Ceramic formulations with different maximum percentage (1%, 5% and 10%) of the residue were shaped by uniaxial pressing at 250 MPa and sintered between 1100 and 1400 ° C for 1 h. The technological properties were determined on the basis of residue content and sintering temperature. The phase transformations and microstructure were examined by XRD and SEM. The bulk density (MEA) samples containing 1% by mass of coffee residue, and sintered at 1350 ° C was 2.7 g / cm3. (author)

  13. Obtaining, characterization and fibre use of nanostructured TiO{sub 2} doped with tungsten as photocatalysts; Obtencao, caracterizacao e utilizacao de fibras nanoestruturadas de TiO{sub 2} dopadas com tungstenio como fotocatalisadores

    Energy Technology Data Exchange (ETDEWEB)

    Soares, L.G.; Bergmann, C.P.; Alves, A.K., E-mail: lugoes.soares@gmail.com [Universidade Federal do Rio Grande do Sul (UFRS), Porto Alegre, RS (Brazil). Laboratorio de Materiais Ceramicos

    2016-07-01

    The use and applicability of nanomaterials are increasingly common in our day to day, due to propitiate more effective end products, lightweight and low cost. The nanomaterials used preferably in various applications is due to properties such as reduced particle size, diversified and high surface area. In this work nanostructured fibers of TiO{sub 2} and TiO{sub 2}/WO{sub 3} were obtained by electrospinning, annealed at temperatures between 650 deg C and 800 deg C, and its photocatalytic activity was evaluated. The technique of X-ray diffraction (XRD) was used to determine the crystalline structure and crystallite size. The morphology of nanomaterials was observed by scanning electron microscopy (SEM). Preliminary results indicate that the nano-doped tungsten presented more efficient in bleaching methyl orange dye, indicating a higher catalytic activity of this material compared to a standard catalyst. This phenomenon can be explained through the phases present and morphological characteristics of the fibers. (author)

  14. Chemical characterization of xyloglucan obtained from Tamarindus indica seeds from the semi arid northeastern; Caracterizacao quimica de xiloglucana obtida a partir de sementes de Tamarindus indica oriundas do semi arido nordestino

    Energy Technology Data Exchange (ETDEWEB)

    Rodrigues, Delane da C.; Cunha, Arcelina P.; Silva, Sarah M.F.; Gallao, Maria Izabel, E-mail: izagalao@gmail.com [Rede Nordeste de Biotecnologia (RENORBIO), Fortaleza, CE (Brazil). Centro de Ciencia; Azeredo, Henriette M.C. de [EMBRAPA Agroindustria Tropical, Fortaleza, CE (Brazil)

    2013-07-01

    Playing an important role in food, seeds are sources of carbohydrates, proteins and lipids, so they have been explored for a long time by the food industry. For this reason, the objective of present work is to obtain and characterize xyloglucan obtained from tamarind seeds (Tamarindus indica). In order to assess possible industrial applications of the polysaccharide, it was characterized by Infrared Fourier Transform spectroscopy (FTIR), Nuclear Magnetic Resonance (NMR) and Thermogravimetric Analysis (TGA). Search results showed that it was possible to perform xyloglucan extraction but the process still requires improvements in order to increase the extraction yield. FTIR, NMR and TGA results were similar to those found in literature. (author)

  15. Chemical characterization of xyloglucan obtained from Tamarindus indica seeds from the semi arid northeastern (Brazil); Caracterizacao quimica de xiloglucana obtida a partir de sementes de tamarindus indica oriundas do semi arido nordestino

    Energy Technology Data Exchange (ETDEWEB)

    Rodrigues, Delane da C.; Cunha, Arcelina P.; Silva, Sarah M.F.; Gallao, Maria Izabel, E-mail: izagalao@gmail.com [Rede Nordeste de Biotecnologia (RENORBIO), Forteleza, CE (Brazil). Centro de Ciencia; Universidade Federal do Ceara (UFC), Fortalea, CE (Brazil); Azeredo, Henriette M.C. de [EMBRAPA Agroindustria Tropical, Fortaleza, CE (Brazil)

    2015-07-01

    Playing an important role in food, seeds are sources of carbohydrates, proteins and lipids, so they have been explored for a long time by the food industry. For this reason, the objective of present work is to obtain and characterize xyloglucan obtained from tamarind seeds (Tamarindus indica). In order to assess possible industrial applications of the polysaccharide, it was characterized by Infrared Fourier Transform spectroscopy (FTIR), Nuclear Magnetic Resonance (NMR) and Thermogravimetric Analysis (TGA). Search results showed that it was possible to perform xyloglucan extraction but the process still requires improvements in order to increase the extraction yield. FTIR, NMR and TGA results were similar to those found in literature. (author)

  16. Porous HA-Al{sub 2}O{sub 3} composite characterization using corn starch as a porogen agent; Caracterizacao do composito poroso HA - Al{sub 2}0{sub 3} utilizando amido de milho como agente porogenico

    Energy Technology Data Exchange (ETDEWEB)

    Silva, L.A.J. da; Galdino, A.G.S.; Cardoso, G.B.C.; Zavaglia, C.A.C., E-mail: l101255@fem.unicamp.br [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Faculdade de Engenharia Mecanica. Departamento de Engenharia de Materiais

    2011-07-01

    The porous ceramics based on hydroxyapatite have great potential for application in bone grafts due to its chemical similarity with the mineral phase of bone tissue, but have poor biomechanical properties, which cause limitations in its applications. This work aims to analyze the structural characteristics of porous ceramics obtained by addition of hydroxyapatite (HA, sintered in the laboratory), Corn Starch (CS, commercial) and Al{sub 2}O{sub 3} (ALCOA), at different temperatures. Samples were made of dense HA (100% HA), porous (70% HA - 30% CS) and with addition of 2.5%, 5% and 7.5% Al{sub 2}O{sub 3} porous composition. The samples were sintered at 1250°C, 1300 deg C and 135 0°C and characterized by: XRF, XRD, SEM and density by the Archimedes method. Concludes It is the possibility of obtaining samples porous HA / Al{sub 2}O{sub 3} using starch as porogenic agent. The temperature and concentration of Al{sub 2}O{sub 3} most appropriate were: 1250°C and 7.5%. (author)

  17. Synthesis and characterization of tungsten carbide doped cobalt via gas-solid reaction in rotary bed reactor; Sintese e caracterizacao de carbeto de tungstenio dopado com cobalto via reacao gas-solido em reator de leito rotativo

    Energy Technology Data Exchange (ETDEWEB)

    Tertuliano, R.S.C.; Araujo, C.P.B. de; Frota, A.V.V.M.; Moriyama, A.L.L.; Souza, C.P. de, E-mail: ruasavio@hotmail.com [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil). Departamento de Engenharia Quimica

    2016-07-01

    The search for materials with high added value, high applicability and sustainability, motivates innovations in all areas of engineering. In this context, so-called doped carbides, ceramic and metal compounds are included. This work proposes the synthesis and characterization of tungsten carbide doped cobalt (WC-Co) through the gas-solid reaction in a rotating bed reactor. The production stages of the material are: precursor synthesis by wetting, drying at 80 deg C, characterization of the precursor by MEV, DRX and FRX, gas-solid reaction at 750 deg C in a reducing atmosphere of CH{sub 4} / H{sub 2} in a rotary reactor at 34 rpm and characterization of the reaction product by the techniques already mentioned. The results showed that tungsten carbide powders were produced with cobalt inserted into the structure, with high surface area, nanometric grains and with potential for applications in the areas of catalysis, reactors and fuel cells, showing the relevance of this type of research.

  18. Stochastic modeling applied to characterization of Namorado field reservoir (Bacia de Campos - RJ, Brasil); Modelagem estocastica aplicada a caracterizacao do reservatorio de campo de Namorado (Bacia de Campos - RJ, Brasil)

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Caio Graco Pereira; Clennell, Bennedict [Bahia Univ., Salvador, BA (Brazil). Curso de Pos-graduacao em Geofisica]. E-mail: cgps@cpgg.ufba.br; clennell@cpgg.ufba.br; Mato, Luiz Ferradans [PETROBRAS, Salvador, BA (Brazil). Exploracao e Producao]. E-mail: ferradans@petrobras.com.br

    2003-07-01

    The Namorado field is in the centre of the Campos Basin, 70 km from shore, between the 150 and 250 m isobaths. This field is divided into four blocks separated by faults. The main blocks have several levels of turbiditic sands interfingering with shale. The external geometry of the sand bodies is lenticular aligned in the direction NW/SE. The media thickness of the genetic units is 160 m, the thickness of porous sandstones varies from 5 to 105 m. The main faciologic types that occurs in the Namorado field do not have internal structure, leading to poor discrimination of internal characteristics. For application of stochastic modeling to the Namorado reservoir log data and core data, were grouped into reservoir and non-reservoir according to the facies, in addition to the application of the binary discriminant function. The method of simulation used was the Sequential Indicator Simulation. The anisotropy defined was 100:1 in the horizontal direction, the structure has transverse isotropy with a range of 40 m (obtained from the experimental variogram). After several model realizations were averaged, the predicted pattern of reservoir facies distribution (probability of reservoir a quality) were combined, and to correlate well with published sections and other quality indicators. (author)

  19. Synthesis and characterization of polyaniline/clay conducting nanocomposites for use in protective coatings; Sintese e caracterizacao de nanocompositos condutores de polianilina/argila para utilizacao em revestimentos protetores

    Energy Technology Data Exchange (ETDEWEB)

    Baldissera, A.F.; Ferreira, C.A.; Senisse, C.A.L.; Oliveira, L.S., E-mail: alebaldissera@hotmail.co [Universidade Federal do Rio Grande do Sul (LAPOL/UFRGS), Porto Alegre, RS (Brazil). Lab. de Materiais Polimericos

    2010-07-01

    Nanomaterials have been shown highly promising materials for various technological applications. In engineering, may be noted the polymer nanocomposites, which are a new class of composite materials, where a nanoclay, or charge with nanometric dimensions, is dispersed in a polymer matrix at low concentration or volume. The clays are more common and when added in quantities less than 5% in the nanocomposites, cause a significant increase in these properties, such as mechanical, optical, magnetic barrier, and especially permeability and flammability. In this context, this work aimed at obtaining the polymeric nanocomposites of polyaniline (PAni) with different commercial clays (cloisite Na{sup +}, 10A and 30B). The preparation of PAni-MMT nanocomposites was performed by in situ polymerization of aniline in acidic (HCl). Electrical conductivity measurements, infrared spectroscopy and X-ray diffraction were some of the techniques used to characterize the nanocomposites. (author)

  20. Characterized and cleaning process of montmorillonite clay from Parelhas, Rio Grande do Norte state, Brazil; Caracterizacao e processo de purificacao de argila montmorilonitica da cidade de Parelhas, RN, Brasil

    Energy Technology Data Exchange (ETDEWEB)

    Melo, G.N; Costa, T.C.C; Paskocimas, C.A, E-mail: gudson.nicolau@gmail.co [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)

    2010-07-01

    The application of montmorillonite nano composites has been improved in order to obtain dispersed phase with particles of nano metric dimensions. To obtain these nanoparticles, the clays must pass an effective purification process for removing unwanted materials, which would undermine the processes of intercalation and exfoliation of montmorillonite in a polymer matrix. This study intention to characterize and purify a montmorillonite clay from deposit recently discovered in the city of Parelhas in Rio Grande do Norte, through the separation of coarser materials by decantation followed by a chemical attack that promoted oxidation in samples where it was realized reduction of impurities such as organic matter and other substances that would hinder the achievement of nanoparticles. Under these conditions, the clay is suitable for the work as dispersed phase in a polymer matrix nano composite. The results were demonstrated by analysis of scanning electron microscopy (SEM), chemical analysis, BET and X-ray diffraction (XRD). (author)

  1. Processing and characterization of biocomposites Poly (3-hydroxybutyrate) / hydroxyapatite for temporary support in bone regeneration; Processamento e caracterizacao de biocompositos Poli (3-hidroxibutirato) / hidroxiapatita para suporte temporario na regeneracao ossea

    Energy Technology Data Exchange (ETDEWEB)

    Cardoso, Cyntia Esteves; Ferreira, Willian Hermogenes; Andrade, Cristina Tristao [Universidade Federal do Rio de Janeiro (UFRJ), Rio de Janeiro, RJ (Brazil). Centro de Tecnologia. Instituto de Macromoleculas Professora Eloisa Mano

    2011-07-01

    Composite materials like biopolymer / hydroxyapatite (HA) has been attracting the interest of researchers because of its applications in medicine. These materials have been used as temporary supports during the regeneration of bone tissue. In this work, poly (3-hydroxybutyrate) (PHB) was chosen as matrix because it has good processability and biocompatibility. The HA was obtained by precipitation from calcium hydroxide and phosphoric acid, varying the speed of dripping, the synthesis temperature and time of calcination. The techniques of infrared absorption spectroscopy and X-ray diffraction (XRD) were used to characterize the samples synthesized HA. The biocomposites were prepared in an internal mixer, with compositions PHB / HA varied. After processing, the biocomposites were ground, characterized by XRD analysis and the crystallinity index. The aim of this study was to examine the variables during the synthesis of HA and its thermal treatment in order to obtain a powder of HA using a simple technique and accessible, creating good properties for the biocomposites prepared. (author)

  2. Study of characteristics of a two phase biomaterial hydroxyapatite / β -tricalcium phosphate 60/40 the composition in volume; Estudo de caracterizacao de um biomaterial bifasico hidroxiapatita/fosfato tricalcio - β na composicao 60/40 em volume

    Energy Technology Data Exchange (ETDEWEB)

    Dalmonico, G.M.L.; Passoni, L.; Prandi, R.G.; Camargo, N.H.A.; Gemelli, E., E-mail: gidalmonico@gmail.com [Universidade do Estado de Santa Catarina (CCT/UDESC), Joinville, SC (Brazil). Centro de Ciencias Tecnologicas. Programa de Pos-Graduacao em Ciencias e Engenharia de Materiais

    2011-07-01

    This work has developed on the preparation and characterization of the composition of biphasic hydroxyapatite /β-calcium phosphate = 60/40%. The mixture composition was performed using the mechanical fragmentation process in an attrition mill for 1 hour. The powder recovered from the biphasic attrition mill after drying, was subjected to compression, to obtain the specimens, the dimensions of 10mm height and 5mm in diameter. The specimens obtained from compaction were sintered at temperature of 1100 ° C/2h. The recovered material was subjected to sintering studies of characterization: compression, hardness and porosity. The results showed a breakdown voltage greater than 76.27 ± 13.56, higher than the microhardness 572.80 ± 13.31 MPa and the porosity of around 40% by volume. The results of the composition biphasic hydroxyapatite /β-calcium phosphate are encouraging, since the biomaterial presented favorable conditions for biomedical applications in the reconstitution of the bone structure. (author)

  3. Aging and characterization of PVC compound used as flat-panel of a low cost solar collector; Envelhecimento e caracterizacao de compostos de PVC usado em placas de coletores solares de baixo custo

    Energy Technology Data Exchange (ETDEWEB)

    Prado, Bruna R.; Pinto, Tatiana T.; Bartoli, Julio R. [Depto. de Tecnologia de Polimeros, Faculdade de Engenharia Quimica/Universidade Estadual de Campinas. FEQ/UNICAMP, SP (Brazil)], e-mail: bartoli@feq.unicamp.br; Fernandes, Elizabeth G. [Tezca P and D Celulas Solares (Brazil)

    2011-07-01

    Regardless the excellent amount of solar irradiation in Brazil, the development and production of solar water heating systems did not reach the low-income families yet. The relatively high cost of conventional solar water heaters is still the main reason to prevent it. The development of a low cost solar water heater (around US$ 200), easy technology, was the scope of previous work. All-plastic solar collector prototypes were developed using unplasticized Poly (vinyl chloride) ceiling panels and tubes, commodities from building engineering. Nevertheless, the main thermal and photo degradation mechanisms for PVC are well known; the unusual application of PVC as solar collector materials should need a specific investigation on environmental aging. This work presents a study on outdoor aging and characterization of PVC flat-plate absorber of solar collectors after 5 years on use. (author)

  4. Evaluation of the mineralogical characterization of several smectite clay deposits of the state of Paraiba, Brazil using statistical analysis of variance; Avaliacao da caracterizacao mineralogica de diversos depositos de argilas esmectiticas do estado da Paraiba utilizando analise estatistica de variancia

    Energy Technology Data Exchange (ETDEWEB)

    Gama, A.J.A.; Menezes, R.R.; Neves, G.A.; Brito, A.L.F. de, E-mail: agama@reitoria.ufcg.edu.br [Universidade Federal de Campina Grande (UFCG), PB (Brazil)

    2015-07-01

    Currently over 80% of industrialized bentonite clay produced in Brazil in sodium form for use in various industrial applications come from the deposits in Boa Vista - PB. Recently they were discovered new bentonite deposits situated in the municipalities of Cubati - PB, Drawn Stone - PB, Sossego - PB, and last in olive groves - PB, requiring systematic studies to develop all its industrial potential. Therefore, this study aimed to evaluate chemical characterization several deposits of smectite clays from various regions of the state of Paraíba through the analysis of statistical variance. Chemical analysis form determined by fluorescence x-ray (EDX). Then analyzes were carried out of variance statistics and Tukey test using the statistical soft MINITAB® 17.0. The results showed that the chemical composition of bentonite clay of new deposits showed different amounts of silica, aluminum, magnesium and calcium in relation clays in Boa Vista, and clays imported. (author)

  5. Physicochemical characterization of steel slag post-processed as aggregate for sustainable concrete; Caracterizacao fisico-quimica de agregados de escoria de aciaria LD pos-processada para concretos sustentaveis

    Energy Technology Data Exchange (ETDEWEB)

    Souza, B.P. de; Fontes, W.C.; Carvalho, J.M.F. de; Mol, R.M.R.; Costa, E.C.P. da; Peixoto, R.A.F., E-mail: wannarquit@gmail.com [Universidade Federal de Ouro Preto (LMC/UFOP), MG (Brazil). Laboratorio de Materiais de Construcao Civil

    2016-07-01

    The concrete is the material most widely used in construction, consuming a large amount of natural resources for its production. Therefore, this work analyzes the technical and environmental aspects of concrete with full replacement of natural aggregates for processed LD steelmaking slag. The experimental program comprehends physical characterization - particle size distribution, moisture content, bulk and specific density - and elemental chemical characterization with X-Ray Fluorescence, and mineralogical characterization via X-Ray Diffraction. Morphological characterization was performed through a stereomicroscope. From these results, concrete with compressive strengths of 20 and 40 Mpa were developed, with ABPC methodology. These were characterized in the fresh and hardened states, obtaining results favorable to the steelmaking slag application in Portland cement concrete. This sustainable concrete features properties similar conventional concrete, and contributing to sustainability of buildings. (author)

  6. Chemical characterization of composites developed from glycerol and dicarboxylic acids rein forced with piassava fiber; Caracterizacao quimica de compositos desenvolvidos a partir do glicerol e acidos dicarboxilicos reforcados com fibra de piacava

    Energy Technology Data Exchange (ETDEWEB)

    Miranda, Cleidiene S.; Oliveira, Jamerson C.; Guimaraes, Danilo H.; Jose, Nadia M., E-mail: cleidienesm@gmail.com [Universidade Federal da Bahia, Instituto de Quimica, GECIM - Programa de Pos-Graduacao em Engenharia Quimica, Salvador, BA (Brazil); Carvalho, Ricardo F. [Universidade Federal da Bahia, Escola Politecnica, Mestrado em Engenharia Ambiental Urbana, Salvador, BA (Brazil)

    2011-07-01

    In search of alternative technologies that enable the use of products with lower environmental impact, This study aims to develop a composite polymer-based piassava fiber. The sludge, waste and byproduct of commercial uses currently being used as reinforcement in polymer matrices, due to presence of lignocellulosic materials. The matrix polymer used was synthesized from glycerol with dicarboxylic acids, in order to open future perspectives on the use of glycerin generated from purified biodiesel production plastics. Composites with 2, 5, 10 wt% of piassava fiber cut into 5 mm raw and treated were obtained a mixture of solution. The materials were characterized by TGA, DSC, XRD and SEM. It was observed that the material under study is promising for the industrial market, because it has good compatibility with natural fibers allowing wider application of fiber natural and glycerol, producing semicrystalline composites and with good thermal properties. (author)

  7. Microstructural characterization of porous materials by X-ray microtomography and gamma ray transmission techniques; Caracterizacao da microestrutura de materiais porosos por microtomografia de raios X e transmissao de raios gama

    Energy Technology Data Exchange (ETDEWEB)

    Moreira, Anderson Camargo

    2006-07-01

    This work presents the application of the X-ray microtomography and gamma ray transmission techniques for the microstructure characterization of different kinds of materials. Total porosity, pore size distribution and the two point correlation functions were measured. The two point correlation function, which allows the reconstruction of 3D models, was carried out for two samples. Seven ceramic tablets of Alumina (Al{sub 2}O{sub 3}), seven tablets of Boron Carbide (B{sub 4}C), three samples of sedimentary rocks and one sample of Titanium foam were analyzed. The experimental set up for the Gamma Ray Transmission technique consisted of: a 2'' x 2'' crystal NaI(Tl) detector, an {sup 241} Am radioactive source (59,53 keV, 100 mCi), an automatic micrometric table for the sample XZ movement and standard gamma spectrometry electronics. Two microtomography systems were used: a Fein Focus system, constituted by an X-ray tube, operated at 160 kV and 0.3 to 1.1 mA, a CCD camera and the movement sample system, and a Skyscan system, model 1072, with a X-ray tube operated at 100 kV and 100{mu}A, and a CCD camera. The ceramic tablets, analyzed by the gamma ray transmission technique presented results for most of the porosities data with smaller confidence intervals and inside the intervals supplied by the tablets manufacturer. The Titanium porous sample was analyzed by the two techniques, its microtomography images achieved a resolution of 17{mu}m, obtained employing the Fein Focus system. For both techniques, this sample showed high porosity, which allows its application for this purpose. The sandstones samples were analyzed by the Skyscan system, achieving resolutions of 19{mu}m, 11{mu}m and 3.8{mu}m for each sample, respectively. The resolutions of 11{mu}m and 3.8{mu}m were the ones that generated better 2D sections for the respective samples and, consequently, more reliable porosities. The 3.8{mu}m resolution was the one that best quantified the pore size

  8. Development of a pilot fluidized bed combustion to NOx reduction using natural gas: characterization and dimensioning; Desenvolvimento de um combustor piloto a leito fluidizado para reducao de NOx usando gas natural: caracterizacao e dimensionamento

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Douglas A.; Lucena, Sergio [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil)

    2004-07-01

    At the present time, the operation of combustion systems and the design of combustors continue being important problems in the Engineering, and don't involve just the size increase of combustors, but also changes of characteristics in the details of projects. The combustors applications are directly related to the needs, like: material transformation for heating, drying or incineration; and all have the inconvenience of emanating of pollutant gaseous (such like NOx). In combustion systems of gases, NOx is basically created in the reaction between nitrogen and oxygen to high temperatures ({approx} 1200 deg C). Below such conditions, the contribution of thermal NOx is recognisably small. The efficient reduction, safe control and economical elimination of pollutant emissions in the systems of burning are the main focuses of environmental legislation and concern to several industrialized countries, besides Brazil. Furthermore, in appeal at the Environmental Laws and at the rising consumption of combustible gases (Natural Gas), new technologies more attractive and economically viable have been studied, for example the combustion systems in fluidized bed. In this kind of system is possible to obtain high combustion efficiency at low temperatures ({approx} 900 deg C) with NOx reduction. In this work is intended of characterizing and dimensioning an industrial fluidized bed combustor that uses Natural Gas like feedstock in the combustion system, with smaller amounts of emitted NOx. (author)

  9. Software development for a orifice plate characterization used in the oil and gas industry; Desenvolvimento de um 'software' para caracterizacao de placas de orificio utilizadas na industria do petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Andreas, N. Andreas [Universidade Federal de Itajuba (UNIFEI), MG (Brazil)

    2008-07-01

    The petroleum industry is an economic area that has a strong impact, because this, the information precision is one of the most important facts and it is able to be defined with software simulation. The knowledge of the exactly quantify of petroleum is fundamental, and then the instrumentation is essential for this measurement. There are many mechanisms to measure the volume flow, and one of the most used is the Orifice Plates, which has been more common in the Natural Gas Industry. The software development goal is the characterization of these Orifice Plates, allowing that the constant, which characterizes certain Plate, to be determined without Labor instruments, for that the software has an actualized database. But, the software needs some variables, that are responsible for the environment characteristics and the used material, to calculate the constant of the Orifice Plate, for example, fluid viscosity, environment temperature and kind of the Orifice Plate. The utilized equations in this software are based on the Stolz II equations. This tool is able to facilitate the work in petroleum industry, besides it is done for mobile applications, allowing analyses in real time. (author)

  10. The geomechanical characterization of the rocky mass foundation of the Tijuco Alto hydroelectric power plant, Ribeira River, Sao Paulo/Parana States, Brazil; Caracterizacao geomecanica do Macico de Fundacao da UHE Tijuco Alto (Rio Ribeira - SP/PR)

    Energy Technology Data Exchange (ETDEWEB)

    Figueiredo, Amarilis Lucia Casteli de

    1996-07-01

    This work has as its main objective the geomechanical characterization on the future rocky mass foundation of the Tijuco Alto dam, sited at the Ribeira river, in the cities of Ribeirao, Sao Paulo state and Adrianopolis, Parana state, Brazil, owned by the Companhia Brasileira de Aluminio (Brazilian company of Aluminium). To reach that target, field studies were made to qualify the geotechnical parameters of the rocky mass, in the axis area open galleries. It was also used in situ deformability and stress test results performed in those galleries, that were reinterpreted for a better adaptation of the mass values. The knowledge of the mass inherent characteristics together with the laboratories test results, allowed for the geomechanical classification applications in several different gallery sectors. The geomechanical data obtained allowed through mathematical expressions, to reach the rocky mass values correlations of interest to the work (deformability and strength), that could be compared to the in situ test results. That analysis permitted, besides the classification critical system evaluation, the geomechanical characterization of the rocky mass, focusing its ability to the dam arch construction. (author)

  11. Characterization of dispersion of a nano composites PP/TiO{sub 2} non modified; Caracterizacao da dispersao dos nanocompositos de PP/TiO{sub 2} nao modificados

    Energy Technology Data Exchange (ETDEWEB)

    Soares, Igor L.; Tavares, Maria I.B.; Silva, Vanessa A. da; Legramanti, Cintia, E-mail: igorl@ima.ufrj.br [Universidade Federal do Rio de Janeiro - UFRJ, Instituto de Macromoleculas - IMA (Brazil); Luetkmeyer, Leandro [Universidades Federais do Mato Grosso - UFMT, Escritorio de Inovacao Tecnologica - EIT (Brazil)

    2011-07-01

    Polymeric nano composites are composite materials where an inorganic particle, which has a dimension in the nanometer range, is dispersed in a polymer matrix. Nano composites, using polypropylene (PP) as matrix polymer and titanium dioxide (TiO{sub 2}) as filler, have great versatility in marketing applications, this factor is inherent in the PP and the inherent ability photo degraded TiO{sub 2} particles. This combination can lead to a widely used material and a degradation time after discharge reduced, there by becoming, a residue of low environmental impact. This study aimed to evaluate the dispersion and particle distribution of TiO{sub 2}, non modified, in PP matrix, using the process of preparation by melt extrusion pathway and characterization of the materials obtained: on the molecular dynamics, using low field NMR solid state, measures the relaxation time spin-network (T{sub 1}H); morphology using XRD technique, and thermal analysis technique with the TGA of pure PP and nano composites PP/TiO{sub 2}. (author)

  12. Discriminant analysis applied to characterization of Namorado field reservoir (Bacia de Campos - RJ, Brasil); Analise discriminante aplicada a caracterizacao do reservatorio do Campo de Namorado (Bacia de Campos - RJ, Brasil)

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Caio Graco Pereira; Clennell, Bennedict [Bahia Univ., Salvador, BA (Brazil). Curso de Pos-graduacao em Geofisica]. E-mail: cgps@cpgg.ufba.br; clennell@cpgg.ufba.br; Mato, Luiz Ferradans [PETROBRAS, Salvador, BA (Brazil). Exploracao e Producao]. E-mail: ferradans@petrobras.com.br

    2003-07-01

    The Namorado field is in the centre of the Campos Basin. The external geometry of the sand bodies is lenticular aligned in the direction NW/SE. In the study, the lithofacies were grouped on the basis of the reservoir characteristics and general rock type in order to simplify the discrimination function. The lithofacies were grouped into: conglomerates and conglomeratic, massive stratified and interfingering sands and clay, diamicitites, slumps and clay stones. Regarding reservoir quality, the lithofacies were grouped into: continuous and stratified reservoir, nonreservoir rocks and flow barriers. Data samples can form two or more groups of objects, and there is no a priori knowledge of the spatial arrangement of the objects or of the determining characteristics of the populations, from which the samples were taken. For application of multivariate analysis in the Namorado Field, it is first necessary to divide the lithologies into reservoir rocks and non-reservoir rocks. A linear equation was obtained that combines variables from log data. The binary discriminant, applied to logged intervals for winch core data was available was 80% successful in placing the lithologies into the right categories. With this equation, it was possible to categorize the lithologies in uncored holes based only on the log data. (author)

  13. Viscoelastic characterization of carbon fiber-epoxy composites by creep and creep rupture tests; Caracterizacao viscoelastica por meio de ensaios de fluencia e ruptura por fluencia de compositos polimericos de matriz de matriz de resina epoxidica e fibra de carbono

    Energy Technology Data Exchange (ETDEWEB)

    Farina, Luis Claudio

    2009-07-01

    One of the main requirements for the use of fiber-reinforced polymer matrix composites in structural applications is the evaluation of their behavior during service life. The warranties of the integrity of these structural components demand a study of the time dependent behavior of these materials due to viscoelastic response of the polymeric matrix and of the countless possibilities of design configurations. In the present study, creep and creep rupture test in stress were performed in specimens of unidirectional carbon fiber-reinforced epoxy composites with fibers orientations of 60 degree and 90 degree, at temperatures of 25 and 70 degree C. The aim is the viscoelastic characterization of the material through the creep curves to some levels of constant tension during periods of 1000 h, the attainment of the creep rupture envelope by the creep rupture curves and the determination of the transition of the linear for non-linear behavior through isochronous curves. In addition, comparisons of creep compliance curves with a viscoelastic behavior prediction model based on Schapery equation were also performed. For the test, a modification was verified in the behavior of the material, regarding the resistance, stiffness and deformation, demonstrating that these properties were affected for the time and tension level, especially in work temperature above the ambient. The prediction model was capable to represent the creep behavior, however the determination of the equations terms should be considered, besides the variation of these with the applied tension and the elapsed time of test. (author)

  14. Technological characterization of a mineral deposit. A case study: the niobium of Catalao I, Goias State, Brazil; Caracterizacao tecnologica de um deposito mineral. Um estudo de caso: o niobio de Catalao I, Goias

    Energy Technology Data Exchange (ETDEWEB)

    Sant`Agostino, Lilia Mascarenhas

    1996-12-31

    This thesis presents a contribution to the subject of ore technological characterization integrated to orebody context, regarding sample, ore characteristics, ore types definition and distribution through the mineral occurrence, and ore reserves modeling using technological parameters. A professional experience in this specialization based a conceptual discussion of the matter, supported by a practical approach. The initial approach is the subject definition, and it`s importance for technological and economical feasibility studies, in all phases of mining research and development, as a tool for beneficiation alternatives definition. The multidisciplinary aspect of the knowledge involved for ore characterization is remarked, considering that is an interface segment to be conduced interactively with others. It is an applied mineralogy, that needs some geological and some ore dressing imputes. After the general considerations about importance and applicability, it follows a methodological approach of laboratory procedures and analytical techniques, as a result of practical experience acquired in the study of several ores. The main points discussed are related with criterion to organized laboratory preparation scheme and to select appropriated analytical techniques, without detailing them, for what some specialized bibliography is indicated. Finalizing the theoretical explanation, there is a concise description about computers resources for 3D orebody modeling, and integrated software applied for geology and mining. For illustration, it is exposed a complex ore case study: niobium mineralization associated with the alkaline-carbonatitic occurrence of Catalao I, located in Goias State, Brazil. Besides the explanation of laboratory procedures and methods applied, results treatment and interpretation are emphasized, under both characterization and economic point of view. (author) 135 refs., 57 figs., 38 tabs.

  15. Elaboration of protocol for characterization of clay as a filling material and coverage for surface repository; Elaboracao de protocolo para caracterizacao de argilas como material de recheio e de cobertura para repositorio de superficie

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Daisy Mary Marchezini dos

    2017-04-01

    The nuclear energy in its various applications generates wastes that must be properly treated. The Radioactive Waste Management covers operations since generation of the waste until to its storage in repository ensuring the protection of man and of environment of the possible negative impacts. The radioactive waste are segregated, treated, conditioned in suitable packaging and posteriorly are stored or disposal in repository. The “RBMN Project” is a priority project of CNEN to implementation the repository for the deposition of low and intermediate level radioactive waste generated by nuclear energy activities in Brazil, proposing a definitive solution for its storage. Engineered and natural barriers as the filling layer and coverage layer will compose the disposal system of a near surface repository, concept proposed by the “RBMN Project”. The use these barriers views to avoid or restrict the release of radionuclides present in waste for the humans beings and environment. The waterproofing barriers are composed of clays. Certainly, for the national repository, will be used those clays existing in the place where it will be implanted it. So some fundamentals tests will have to be carried for to verify the suitability of these clays as barriers. These tests were determined and realized with a reference clay, a brazilian bentonite constituted of 67.2% montmorillonite. The results were compared with national and international literature of materials with similar mineralogical features. The values found with 95% reliance were 9.73±0,35 μm for granulometric size. For the moisture content were 13,3±0,6% and for capacity of cationic exchange were , 816±9 mmol.kg{sup -1}. For the hydraulic conductivity, without the use of internal pressure, it was obtained maximum value of 59.0% saturated. In addition, during the observed period, there was no percolation in the test specimen submitted to internal pressure of 200 kPa. This result leads to the conclusion that the

  16. Biopolymer chitin: extraction and characterization; Biopolimero quitina: extracao e caracterizacao

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    The biopolymers are materials made from renewable sources such as soybean, corn, cane sugar, cellulose and chitin. Chitin is the most abundant biopolymer found in nature, after cellulose. The chemical structure of chitin is distinguished by the hydroxyl group, of structure from cellulose, located at position C-2, which in the chitin is replaced by acetamine group. The objective of this study was to develop the chitin from exoskeletons of Litopenaeus vannamei shrimp, which are discarded as waste, causing pollutions, environmental problems and thus obtain better utilization of these raw materials. It also, show the extraction process and deacetylation of chitosan. The extraction of chitin followed steps of demineralization, desproteinization and deodorization. Chitin and chitosan were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and the thermals properties were analyzed by thermogravimetry (TG/DTG). (author)

  17. Obtention and characterization of biodiesel; Obtencao e caracterizacao do biodiesel

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Leonidas B.O. dos; Caitano, Moises; Aranda, Donato A.G.; Mothe, Cheila G. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil)

    2004-07-01

    Biodiesel is an ester resulting from the transesterification reaction of an alcohol and an oil obtained from biomass. The products of the transesterification are an ester and the glycerol. The biodiesel and the petroleum commercial diesel have similar properties, and they can be mixed and used in diesel motors. The use of biodiesel will allow a better exploration of the energetic potential of our cultures. The biodiesel has some advantages compared to others combustibles, such as adaptability to usual diesel motors and non-generation of NO{sub x} and SO{sub x} compounds. Many experiments with biodiesel have been made in Brazil since the 70's. This work made samples of biodiesel by transesterification batch reactions to many blends of soybean oil and residual fry oil, at room temperature, using mechanical mixture or magnetic agitation by a magnetic stirrer, using as catalysts sodium methoxide and potassium hydroxide. For each obtained sample tests to determine the Acidity Index (ABNT-MB-74), Saponification Index (ABNT-MB-75), Iodine Wijz Index (ABNT-MB- 77), thermal analysis by DTA and TG (TA Instruments SDT 2960, 30 to 800 deg C, 10 deg C/min at nitrogen atmosphere) and rheological test (Haake RS 150 Rheo Stress rheometer) were done. (author)

  18. Chemical characterization of marajoara ceramics; Caracterizacao quimica da ceramica marajoara

    Energy Technology Data Exchange (ETDEWEB)

    Toyota, Rosimeiri Galbiati

    2009-07-01

    In this study the elemental concentration of Ce, Co, Cr, Cs, Eu, Fe, Hf, K, La, Lu, Na, Nd, Rb, Sc, Sm, Ta, Tb, Th, U, Yb and Zn were determined by instrumental neutron activation analysis (INAA) in 204 fragments of Marajoara archaeological ceramics, of which 156 were provided by the Archaeology and Ethnology Museum of Sao Paulo University (MAE) and 48 were provided by Dr. Denise Pahl Schaan, Marajo Museum curator. Also, 9 contemporary ceramics produced and marketed at Marajo Island were analyzed. Electron paramagnetic resonance (EPR) analyses were performed in 8 archaeological samples and 1 contemporary sample in order to identify the burning temperature of the samples. X-ray diffraction (XRD) analyses were performed in 13 archaeological samples and 2 contemporary samples for the investigation of their mineralogical composition. Mahalanobis distance was used for the study of outlier while modified filter was used for the study of the temper added to the ceramic paste. Result interpretation was performed using cluster analysis, principal components analysis and discriminant analysis. Procrustes analysis was used for variable selection and it showed that the Ce, Fe, Eu, Hf, K and Th variables are adequate for the characterization of the analyzed samples. The comparative study among the archaeological and contemporary ceramics showed the arrangement of two well-defined and close groups for the archaeological samples and a third, distant group for the contemporary ones. This result indicates that the archaeological and contemporary ceramics differ in their composition. EPR and XRD analysis were inconclusive for the differentiation of archaeological and contemporary ceramics. (author)

  19. Energetic characterization of Amazonian biomass; Caracterizacao energetica de biomassas amazonicas

    Energy Technology Data Exchange (ETDEWEB)

    Feitosa Netto, Genesio Batista; Oliveira, Antonio Geraldo de Paula; Coutinho, Hebert Willian Martins; Nogueira, Manoel Fernandes Martins; Rendeiro, Goncalo [Universidade Federal do Para (UFPA), Belem, PA (Brazil). Dept. de Engenharia Mecanica

    2006-07-01

    In order to asses the potentiality of Amazon biomasses to generate power, either to supply electric energy to the grid or as fuel to plants supplying power for off-grid location, data for their proximate analysis must be available. A literature review on the subject indicated a lack of information and data concerning typical Amazon rain forest species. This work aimed to characterize (proximate analysis) 43 Amazon species in order to evaluate the energy resource from woody biomass wastes in Amazon region. Higher heating value, carbon, volatile and ash contents were measured in a dry basis. The measurements were performed obeying the following Brazilian standards, NBR 6923, NBR 8112, NBR 8633, NBR 6922. (author)

  20. Synthesis and characterization of Ce{sub 1-x}SmXO{sub 2-(x/2)} as solid electrolyte for application in IT-SOFCs; Sintese e caracterizacao de Ce{sub 1-x}SmXO{sub 2-(x/2)} como eletrolito solido para aplicacao em IT-SOFCs

    Energy Technology Data Exchange (ETDEWEB)

    Nicodemo, J.P.; Martinelli, A.E.; Nascimento, R.M. [Universidade Federal do Rio Grande do Norte (DECM/UFRN), Natal, RN (Brazil). Dept. de Engenharia de Materiais], e-mail: juli_pivotto@yahoo.com.br; Melo, D.M.A. [Universidade Federal do Rio Grande do Norte (DQ/UFRN), Natal, RN (Brazil). Dept. de Quimica; Cela, B. [Universidade Federal do Rio Grande do Norte (PPGCEM/UFRN), Natal, RN (Brazil). Programa de Pos-Graduacao em Ciencia e Engenharia de Materiais; Macedo, D.A. [Universidade Federal do Rio Grande do Norte (PPGEM/UFRN), Natal, RN (Brazil). Programa de Pos-Graduacao em Engenharia Mecanica

    2008-07-01

    Mixed rare earth doped CeO{sub 2} oxide-based have been extensively studied for use in solid electrolytes for fuel cells. Ceramics-based CeO{sub 2} have high ionic conductivity and enable the operation of solid oxide fuel cells (SOFCs) in intermediate temperatures, in the range of 500 to 750 deg C. In this work, was investigated the Sm{sub 2}O{sub 3} doped CeO{sub 2} by Pechini method to obtain Ce{sub 0,9}Sm{sub 0,1}O{sub 1,95}. The resulting powders were characterized by the chemical composition (EDS) and crystallographic (XRD), thermal analysis (TG/ATD and DTG), and particles morphology (SEM). After calcinations of 500 and 700 deg C for 2 hours were obtained nanosized powders with crystalline structure of cubic phase type fluorite fully formed. (author)

  1. Synthesis and characterization of nanostructured powders of hydroxyapatite and of three-calcium {beta} phosphate: elaboration of two phase compositions for application in the orthopedics and traumatology; Sintese e caracterizacao de pos nanoestruturados de hidroxiapatita e de fosfato tricalcico {beta}: elaboracao de composicoes bifasicas para aplicacoes na ortopedia e traumatologia

    Energy Technology Data Exchange (ETDEWEB)

    Dalmonico, G.M.L.; Pinheiro, D.M.; Camargo, N.H.A.; Orzechowki, L.G.; Goncalves, A.F.; Melnik, V.; Jesus, J.; Gemelli, E. [Universidade do Estado de Santa Catarina (UDESC), Joinville, SC (Brazil). Centro de Ciencias Tecnologicas], e-mail: gidalmonico@gmail.com

    2010-07-01

    This paper synthesized nano structured hydroxyapatite and three calcium {beta} phosphate, for elaboration of two phase compositions of HA/TCP in the concentration in volume of 80% HA/20% TCP-{beta}, 60% HA/40% TCP-{beta} and 50% HA/50% TCP-{beta}. For phase mixing realization, the method of mechanical fragmentation by attritor mill were used. The material recovered from the process of mechanical fragmentation was dried in rotate evaporator, supplying the two phase compositions. The preliminary studies shown the obtention of nano metric powders and a good phase dispersions inside the two phase compositions. (author)

  2. Surface preparation for XRD residual stress measurements; Preparacao de superficie para medicao de tensoes residuais em soldagem por DRX

    Energy Technology Data Exchange (ETDEWEB)

    Mishchenko, Andrii; Oliveira, Bruno Jose de; Scotti, Americo, E-mail: asmwelder@gmail.com, E-mail: brunojoliveira7@gmail.com, E-mail: ascotti@mecanica.ufu.br [Universidade Federal de Uberlandia (UFU), MG (Brazil)

    2016-10-15

    A characteristic feature of the X Ray Diffraction (XRD) method for stress determination is that measurements occur at a thin surface layer. Steel sheets come with surfaces modified by lamination, cleaning (sandblasting, grinding) and even corrosion, which induce residual stresses or roughness inherent to the material. Therefore, surface preparation prior to the residual stress measurement is essential, although no standard procedure seems to be available. A general recommendation is to remove a thin layer so that only residual stresses related to the welding process will be measured. In this study, the use of portable electrolytic equipment was evaluated for mechanized surface material removal. Chemical compositions of electrolytic solutions and the influence of current on the removed material, removal time and temperature during the process were studied. As a result, a suitable chemical solution for electro etching of low carbon steel was developed and a set of “soft” parameters that allowed the removal of about 300 um in a reasonable time was found. Higher currents reduce the removal time, yet increasing the consumption of the solution and plate temperature (which could adversely alter the microstructure or generate thermal stresses). Furthermore, the influence of these parameters on the operability of the process was demonstrated. (author)

  3. Preparation of lead titanate zirconate from metal citrates; Preparacao do titanato zirconato de chumbo a partir dos citratos metalicos

    Energy Technology Data Exchange (ETDEWEB)

    Bastos, C.M.R.

    1994-12-31

    Lead titanate zirconate (PZT) preparation from its metal constituent citrates have been investigated. Metal citrates were obtained by forced precipitation using a dehydration alcohol mixture. Salt solutions of lead nitrate and octahydrated zirconyl chloride, and titanium tetrachloride were treated separately with citric acid and ammonium hydroxide. Zirconium, titanium and lead oxides resulted from thermal decomposition of corresponding citrates at 500{sup 0} C, 450{sup 0} C and 250{sup 0} C, respectively. Lead titanate (PT) and lead zirconate (P Z) were obtained by calcining at 450{sup 0} C and 500{sup 0} C, respectively, after adequate heating of citrates mechanically mixed in ethyl ether. PZT samples were obtained with different starting stoichiometry. Rhombohedral PZT-1 53/47 sample was prepared from co precipitating zirconyl ammonium and ammonium lead citrates in presence of ethanolic titanium oxide dispersion, and calcinating at 800{sup 0} C. Rhombohedral PZT-q 52/48 sample was obtained from heating at 500{sup 0} C for 2 hours a mixture of metal citrates coprecipitated by dehydration mixture of acetone-ethanol-formic acid (2:1:0,06). Tetragonal PZT-m stoichiometry 53/47 sample were obtained by calcining at after 600{sup 0} C for 2 hours after heating a mechanically mixed metal citrates. PT phase arose at 400{sup 0} C. PZT-m powders obtained in a range of 400{sup 0} C-800{sup 0} C were isostatically pressed, and sintered at 1100{sup 0} C and 1200{sup 0} C in saturated Pb O atmosphere. Rhombohedral sintered PZT was obtained with 7,78 g.cm{sup -3} at 1200{sup 0} C. (author). 123 refs, 53 figs, 32 tabs.

  4. PANI-nanofibers/polyethylene blends: preparation and properties; Blendas de nanofibras de PANI/polietileno: preparacao e propriedades

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, F.; Hubler, R.; Basso, N.R.S., E-mail: nrbass@pucrs.b [Pontificia Universidade Catolica do Rio Grande do Sul (PUC-RS), Porto Alegre, RS (Brazil); Fim, F.C.; Galland, G.B. [Universidade Federal do Rio Grande do Sul (UFRGS), Porto Alegre, RS (Brazil)

    2010-07-01

    In this work polyaniline nanofibers (PANI-nanofibers) were prepared via interfacial polymerization. The PANI-nanofibers were dispersed in polyethylene (PE) matrix by in situ polymerization of ethylene using Cp{sub 2}ZrCl{sub 2} [bis(cyclopentadienyl) zirconium(IV) dichloride)] and methylaluminoxane as catalytic system. The composites were characterized by infra-red spectroscopy, X-ray diffraction, thermal analysis, transmission electron microscopy and scanning electron microscopy. The results show that nanofibers with average diameters of 200 nm were synthesized and that it was obtained well dispersed PE/PANI nanocomposites. The PANI-nanofibers load did not affect the catalytic activity, but it decreased crystallinity degree of nanocomposites. (author)

  5. Medical Applications

    OpenAIRE

    Biscari, C.; Falbo, L.

    2016-01-01

    The use of accelerators for medical applications has evolved from initial experimentation to turn-key devices commonly operating in hospitals. New applications are continuously being developed around the world, and the hadrontherapy facilities of the newest generation are placed at the frontier between industrial production and advanced R&D. An introduction to the different medical application accelerators is followed by a description of the hadrontherapy facilities, with special emphasis on ...

  6. LCA Applications

    DEFF Research Database (Denmark)

    Owsianiak, Mikołaj; Bjørn, Anders; Laurent, Alexis

    2017-01-01

    The chapter gives examples of applications of LCA by the central societal actors in government, industry and citizens, and discusses major motivations and challenges for the use of LCA to support science-based decision-making from their respective perspectives. We highlight applications of LCA in...

  7. Medical Applications

    CERN Document Server

    Biscari, C.

    2014-12-19

    The use of accelerators for medical applications has evolved from initial experimentation to turn-key devices commonly operating in hospitals. New applications are continuously being developed around the world, and the hadrontherapy facilities of the newest generation are placed at the frontier between industrial production and advanced R&D. An introduction to the different medical application accelerators is followed by a description of the hadrontherapy facilities, with special emphasis on CNAO, and the report closes with a brief outlook on the future of this field.

  8. Medical Applications

    International Nuclear Information System (INIS)

    Biscari, C; Falbo, L

    2014-01-01

    The use of accelerators for medical applications has evolved from initial experimentation to turn-key devices commonly operating in hospitals. New applications are continuously being developed around the world, and the hadrontherapy facilities of the newest generation are placed at the frontier between industrial production and advanced R&D. An introduction to the different medical application accelerators is followed by a description of the hadrontherapy facilities, with special emphasis on CNAO, and the report closes with a brief outlook on the future of this field

  9. Photovoltaic applications

    International Nuclear Information System (INIS)

    Sidrach, M.

    1992-01-01

    The most common terrestrial applications of photovoltaic plants are reviewed. Classification of applications can be done considering end-use sectors and load profiles (consumption demand). For those systems with direct coupling the working point is determined by the intersection of the load line with the I-V curve Design guidelines are provided for photovoltaic systems. This lecture focusses on the distribution system and safeguards

  10. PRIBIC Application

    International Nuclear Information System (INIS)

    Pascual Alonso, J.L.; Barcala Riveira, J.M.

    2002-01-01

    PRIBIC plant (Pollutants Reduction In small Biomass Combustion systems) at CEDER is a facility specifically designed to do biomass combustion tests. In these tests is necessary to know the values of different sensors in real time. With this information the PRIBIC plant is regulated to its optimum point of work and its possible to follow the operation criteria and get test objectives. Different electronic instruments record information about the plant operation. A software application was developed to let a centralised motorization of that information. The application communicates with the instrumentation, recovers data, lets operators see data in real time and saves the information in files. An important part of this document describes that application, and some considerations to generalise this kind of developments to other Experimental Plants, including cost estimations. Descriptions of plant, analysis of the problem, result evaluations, and conclusions can also be found in the document. (Author) 13 refs

  11. Technology applications

    Science.gov (United States)

    Anuskiewicz, T.; Johnston, J.; Leavitt, W.; Zimmerman, R. R.

    1972-01-01

    A summary of NASA Technology Utilization programs for the period of 1 December 1971 through 31 May 1972 is presented. An abbreviated description of the overall Technology Utilization Applications Program is provided as a background for the specific applications examples. Subjects discussed are in the broad headings of: (1) cancer, (2) cardiovascular disease, (2) medical instrumentation, (4) urinary system disorders, (5) rehabilitation medicine, (6) air and water pollution, (7) housing and urban construction, (8) fire safety, (9) law enforcement and criminalistics, (10) transportation, and (11) mine safety.

  12. Other applications

    International Nuclear Information System (INIS)

    Ligou, J.; Benoist, P.; Boffi, V.; Stenic, B.

    1981-01-01

    This chapter reports about the work done by four groups in Italy, France, Switzerland and Yugoslavia on the new applications of transport theory. Among them problems dealing with controlled thermonuclear reactions and/or fusion devices, nonlinear electric conductivity, atomic and crystal models were discussed

  13. Application note :

    Energy Technology Data Exchange (ETDEWEB)

    Russo, Thomas V.

    2013-08-01

    The development of the XyceTM Parallel Electronic Simulator has focused entirely on the creation of a fast, scalable simulation tool, and has not included any schematic capture or data visualization tools. This application note will describe how to use the open source schematic capture tool gschem and its associated netlist creation tool gnetlist to create basic circuit designs for Xyce, and how to access advanced features of Xyce that are not directly supported by either gschem or gnetlist.

  14. Determination Application

    Directory of Open Access Journals (Sweden)

    Paula Cristiane Pinto Mesquita Pardal

    2015-01-01

    Full Text Available The paper aims at discussing techniques for administering one implementation issue that often arises in the application of particle filters: sample impoverishment. Dealing with such problem can significantly improve the performance of particle filters and can make the difference between success and failure. Sample impoverishment occurs because of the reduction in the number of truly distinct sample values. A simple solution can be to increase the number of particles, which can quickly lead to unreasonable computational demands, which only delays the inevitable sample impoverishment. There are more intelligent ways of dealing with this problem, such as roughening and prior editing, procedures to be discussed herein. The nonlinear particle filter is based on the bootstrap filter for implementing recursive Bayesian filters. The application consists of determining the orbit of an artificial satellite using real data from the GPS receivers. The standard differential equations describing the orbital motion and the GPS measurements equations are adapted for the nonlinear particle filter, so that the bootstrap algorithm is also used for estimating the orbital state. The evaluation will be done through convergence speed and computational implementation complexity, comparing the bootstrap algorithm results obtained for each technique that deals with sample impoverishment.

  15. Synthesis and characterization of magnetic cobalt ferrite nanoparticles covered with 3-aminopropyltriethoxysilane for use as hybrid material in nano technology; Sintese e caracterizacao de nanoparticulas magneticas de ferrita de cobalto recobertas por 3-aminopropiltrietoxissilano para uso como material hibrido em nanotecnologia

    Energy Technology Data Exchange (ETDEWEB)

    Camilo, Ruth Luqueze

    2006-07-01

    Nowadays with the appear of nano science and nano technology, magnetic nanoparticles have been finding a variety of applications in the fields of biomedicine, diagnosis, molecular biology, biochemistry, catalysis, etc. The magnetic functionalized nanoparticles are constituted of a magnetic nucleus, involved by a polymeric layer with active sites, which ones could anchor metals or selective organic compounds. These nanoparticles are considered organic inorganic hybrid materials and have great interest as materials for commercial applications due to the specific properties. Among the important applications it can be mentioned: magneto hyperthermia treatment, drugs delivery in specific local of the body, molecular recognition, biosensors, enhancement of nuclear magnetic resonance images quality, etc. This work was developed in two parts: 1) the synthesis of the nucleus composed by superparamagnetic nanoparticles of cobalt ferrite and, 2) the recovering of nucleus by a polymeric bifunctional 3-aminopropyltriethoxysilane. The parameters studied in the first part of the research were: pH, hydroxide molar concentration, hydroxide type, reagent order of addition, reagent way of addition, speed of shake, metals initial concentrations, molar fraction of cobalt and thermal treatment. In the second part it was studied: pH, temperature, catalyst type, catalyst concentration, time of reaction, relation ratios of H{sub 2}O/silane, type of medium and the efficiency of the recovering regarding to pH. The products obtained were characterized using the following techniques X-ray powder diffraction (DRX), transmission electronic microscopy (TEM), scanning electronic microscopy (SEM), spectroscopy of scatterbrained energy spectroscopy (DES), atomic emission spectroscopy (ICP-AES), thermogravimetric analysis (TGA/DTGA), Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC) and magnetization curves (VSM). (author)

  16. Development and characterization of ceramic composites alumina-titania based reinforced with lanthanum oxide for fabrication of inert coatings for metallic tanks of the oil industry; Desenvolvimento e caracterizacao de compositos ceramicos baseados em alumina-titania reforcados com oxido de lantanio para fabricacao de revestimentos inertes em tanques metalicos da industria petrolifera

    Energy Technology Data Exchange (ETDEWEB)

    Bandeira, J.M.; Yadava, Y.P.; Silva, N.D.G.; Ferreira, R.A.S., E-mail: julianamb91@gmail.com, E-mail: yadava@ufpe.br [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil). Centro de Tecnologia e Geociencias. Departamento de Engenharia Mecanica

    2016-07-01

    Crude petroleum is highly corrosive causing superficial degradation in metallic tanks used for storage and transportation of this material, which causes a serious problem in the oil industry. An alternative to solve this problem is to use some kind of coating that is inert to this kind of corrosion. Alumina and titania are interesting materials for several engineering applications because, when compared with other ceramic materials, they present superior mechanical properties, e.g. high mechanical strength, good chemical stability and high fracture toughness combined with good wear resistance and a coefficient of thermal expansion close to the iron's, which makes them fit to use in ceramic hardening process and coating. In this paper, alumina-titania ceramic composites with 5%, 10%, 15% and 20% of titania (TiO2) and reinforced with 2% of lanthanum oxide of were produced by thermo-mechanical processing and sintering techniques at 1350 deg C. In these composites, microstructure and mechanical properties were analyzed using X-ray spectroscopy, optical microscopy, scanning electron microscopy and Vickers hardness in order to evaluate their applicability. X-ray spectroscopy showed the formation of composite without the presence of other phases. Optical microscopy and scanning electron microscopy showed a homogeneous microstructure in terms of particle size and distribution. Vickers hardness test showed a gradual decrease in hardness with the addition of titania. The composite with 5% of titania and 2% of lanthanum oxide is the best choice for structural applications. The composites were submerged in crude petroleum for 30 days to study their stability in such environment. Through the analysis of X-ray spectroscopy, optical microscopy and Vickers hardness before and after the submersion in crude petroleum, it was not observed structural or microstructural degradation nether alterations in mechanical properties. This way, it was concluded that these composites have

  17. Synthesis and characterization of Cd{sub x}Mn{sub 1-x}S nanoparticles stabilized with poly(vinyl alcohol); Sintese e caracterizacao de pontos quanticos de Cd{sub x}Mn{sub 1-x}S estabilizados com poli(alcool vinilico)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    Colloidal luminescent semiconductor nanocrystals, also known as quantum dots, have attracted considerable attention due to their significant potential application. The doping of nanocrystalline semiconductors with divalent manganese ions results in new optical properties of these semimagnetic semiconductor quantum dots. In this work we report the synthesis and characterization Cd{sub x}Mn{sub 1-x}S nanoparticles using poly(vinyl alcohol) as stabilizing agent. Different fractions of Cd{sup 2+}/Mn{sup 2+} ions were investigated aiming the production of stable nanoparticles with different photoluminescence properties. (author)

  18. Synthesis and characterization of CdS quantum dots stabilized with poly(vinyl alcohol): effect of molar fraction of precursors; Sintese e caracterizacao de pontos quanticos de CdS estabilizados com poli(alcool vinilico): efeito da fracao molar dos precursores

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    Semiconductor nanoparticles (quantum dots) with size lower than Bohr radius present quantum confinement effect, and properties dependent on particle diameter. The use of these nanoparticles for biological applications is highly promising, however this kind of use requires biocompatible systems. In this sense, the choice of poly(vinyl alcohol), PVA, as stabilizing agent has been investigated. The main goal of this work was synthesize and characterize CdS nanoparticles using PVA as capping agent varying the molar ratio of cadmium and sulfur precursors. The results revealed that absorption and emission properties, as well as nanoparticle size, were function of Cd/S ratio. (author)

  19. Characterization of the potential sites in the Brazilian semi-arid region for implantation of helium thermal pilot system of electric power generation; Caracterizacao dos sitios potenciais na regiao do semi-arido brasileiro para implantacao de sistema piloto heliotermico de geracao eletrica

    Energy Technology Data Exchange (ETDEWEB)

    Guimaraes, Ana Paula Cardoso; Nascimento, Marcos Vinicius Gusmao; Menezes, Paulo Cesar Pires; Cheroto, Silvia [Centro de Pesquisas de Energia Eletrica (CEPEL), Rio de Janeiro, RJ (Brazil)]. E-mails: pcardoso@cepel.br; pcpm@cepel.br

    2004-07-01

    This work contains studies an analyses related to the characterization of the potential sites for application of helium thermal technology at the brazilian semi-arid, with the mapping of the solar resource from the estimative of direct solar radiation data, the mapping of the hydraulic resources indicating the importance of the Sao Francisco basin in the study context, the mapping of the local electric power network, and a survey of the environmental impacts attributed to power plants with solar concentrators. The general objective is to identify the more adequate sites in Brazil for the implantation of a helium thermal pilot system for electric power generation.

  20. Detector applications

    International Nuclear Information System (INIS)

    Pehl, R.H.

    1977-10-01

    Semiconductor detectors are now applied to a very wide range of problems. The combination of relatively low cost, excellent energy resolution, and simultaneous broad energy-spectrum analysis is uniquely suited to many applications in both basic and applied physics. Alternative techniques, such as magnetic spectrometers for charged-particle spectroscopy, while offering better energy resolution, are bulky, expensive, and usually far more difficult to use. Furthermore, they do not directly provide the broad energy-spectrum measurements easily accomplished using semiconductor detectors. Scintillation detectors, which are approximately equivalent to semiconductor detectors in convenience and cost, exhibit 10 to 100 times worse energy resolution. However, their high efficiency and large potential size recommend their use in some measurements

  1. Studies of the development and characterization of the Cu-Ni-Pt and Cu-Ni-Sn alloys for electro-electronic uses; Estudos do desenvolvimento e caracterizacao das ligas Cu-Ni-Pt e Cu-Ni-Sn para fins eletro-eletronicos

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Luis Carlos Elias da

    2006-07-01

    The Cu and its alloys have different applications in the owed modern society the excellent electric properties, thermal conductivity, resistance to the corrosion and other properties. These applications can be in valves, pipes, pots for absorption of solar energy, radiators for automobiles, current driver, electronic driver, thermostats elements and structural parts of nuclear reactors, as, for example, reels for field toroidal for a reactor of nuclear coalition. The alloys used in nuclear reactors, we can highlight Cu-Be, Cu-Sn and Cu-Pt. Ni and Co frequently are added to the Cu alloys so that the solubility is moved for temperatures more elevated with relationship to the binary systems of Cu-Sn and Cu-Pt. The addition of Ni-Pt or Ni-Sn to the Cu in the same or inferior percentages to 1,5% plus thermomechanical treatments changes the properties of the copper. We studied the electric conductivity and hardness Vickers of the Cu-Ni-Pt and Cu-Ni-Sn and compared with the electrolytic Cu. In the proposed flowcharts, breaking of the obtaining of the ingot, we proceeded with thermo mechanical treatments. (author)

  2. Comparative analysis of synthesis and characterization of La{sub 0,9}Sr{sub 0,1}O{sub 3} via sol-gel and combustion reaction; Analise comparativa da sintese e caracterizacao de La{sub 0,9}Sr{sub 0,1}O{sub 3} via sol-gel e via reacao por combustao

    Energy Technology Data Exchange (ETDEWEB)

    Tarrago, D.P.; Haeser, G.S.; Malfatti, C.F.; Sousa, V.C. [Universidade Federal do Rio Grande do Sul (UFRS), Porto Alegre, RS (Brazil). Programa de Pos-Graduacao em Engenharia de Materiais, Minas e Metalurgica

    2011-07-01

    Strontium doped lanthanum manganites (LSM) are potential materials for cathode application in solid oxide fuel cells (SOFC) due to their properties and compatibility with yttria stabilized zirconia. In this work a LSM powder obtained by the sol-gel process is compared others previously obtained combustion synthesis using urea or sucrose as fuel. For the synthesis of LSM the nitrates of lanthanum, strontium and manganese were dissolved in citric acid and ethylene glycol forming a gel that was calcinated at 800 deg C. Both methods allowed the synthesis of a single phase powder, according to the X-ray diffraction patterns. Through gas adsorption it was found a specific surface area of 17m²/g, an intermediary value among the combustion synthesized powders. Scanning electron microscopy (SEM) revealed more compact agglomerates in the sol-gel powder, however, the transmission electron microscope (TEM) showed smaller and more uniform particles in this powder. (author)

  3. Morphological and structural characterization of the Zn{sub 0,9}Mn{sub 0,1}O powder synthesized by combustion reaction and Pechini; Caracterizacao estrutural e morfologica de pos de Zn{sub 0,9}Mn{sub 0,1}O sintetizados por reacao de combustao e metodo Pechini

    Energy Technology Data Exchange (ETDEWEB)

    Ribeiro, M.A.; Torquato, R.; Simoes, A.N.; Costa, A.C.F.M.; Gama, L., E-mail: anacristina@dema.ufcg.edu.b [Universidade Federal de Campina Grande (DEMA/UFCG), PB (Brazil). Dept. de Engenharia dos Materiais; Kiminami, R.H.G.A. [Universidade Federal de Sao Carlos (DEMA/UFSCar), SP (Brazil). Dept. de Engenharia de Materiais

    2009-07-01

    Zinc oxide, due to the piezoelectric and electro-optical characteristics, is used in application such as, chemical sensor, varistor, transparent conductive thin film and DMS. The aim of this work is to evaluate and compare structural and morphological characteristics of nanometric powders of Zn{sub 0,9}Mn{sub 0,1}O prepared by chemical synthesis of combustion reaction and Pechini method. The powders were characterized by XRD, SEM and BET. The XRD data shown to both studied method the presence of ZnO phase with hexagonal structure and without second phase. The powder prepared by combustion reaction presented 9% of reduction in crystallinity and 42% of increase in surface area in comparison with the powder prepared by Pechini method. The morphological analysis of the powder showed that both method produce powders with soft agglomerates constituted by nano size particles. (author)

  4. Developpement and characterization of an DL-Alanine Gel to be applied in the measurement of the dose distribution with the Spectrophotometry Technique; Desenvolvimento e caracterizacao de um gel alanima para aplicacao na medida da distribuicao da dose de radiacao usando a tecnica de espectrofotometria

    Energy Technology Data Exchange (ETDEWEB)

    Mizuno, Erick Yukio

    2007-07-01

    The aim of this work is to develop a DL-Alanine, Fe-II based gel dosimeter to be applied in the dosimetry of the Co-60 gamma-radiation fields in the dose range of radiation therapy procedures. The aminoacid DL-Alanine is dissolved in an acid solution containing the Fe-II and added to the gel. A series of essays was performed with different chemicals and different procedures were made to evaluate the behavior of the obtained dosimetric gel as function of the time. The absorption spectra, before and after the irradiation, present maximum in 457 nm and 588 nm, respectively. These two peaks correspond to absorption wavelengths of the chemical species Fe-II and Fe-III, respectively, both species being in equilibrium. With the irradiation, the formation of the radicals that oxide the Fe-II into Fe-III occurs, altering the chemical balance of both species - hence the increase of the Fe-III - and causing the gel to change its tonality, in such a way that it is possible to determine the absorbed dose. In the analysis of the spectra and respective dose-response curves it was observed that the dosimetric gel shows linearity in dose range of 0.5 to 40 Gy. From the obtained linearity results, stability and lower detectable dose - 0,3 Gy - it is possible to conclude that the present DL-Alanine, Fe-II based dosimetric gel presents an excellent potential to the application to which it is proposed, namely, the determination of the dose fields in radiation therapy and its future application as a standard in the determination of these fields, in 3D, using the Magnetic Resonance Imaging. (author)

  5. Modeling Applications.

    Science.gov (United States)

    McMEEKIN, Thomas A; Ross, Thomas

    1996-12-01

    The concept of predictive microbiology has developed rapidly through the initial phases of experimental design and model development and the subsequent phase of model validation. A fully validated model represents a general rule which may be brought to bear on particular cases. For some microorganism/food combinations, sufficient confidence now exists to indicate substantial benefits to the food industry from use of predictive models. Several types of devices are available to monitor and record environmental conditions (particularly temperature). These "environmental histories" can be interpreted, using predictive models, in terms of microbial proliferation. The current challenge is to provide systems for the collection and interpretation of environmental information which combine ease of use, reliability, and security, providing the industrial user with the ability to make informed and precise decisions regarding the quality and safety of foods. Many specific applications for predictive modeling can be developed from a basis of understanding the inherent qualities of a fully validated model. These include increased precision and confidence in predictions based on accumulation of quantitative data, objective and rapid assessment of the effect of environmental conditions on microbial proliferation, and flexibility in monitoring the relative contribution of component parts of processing, distribution, and storage systems for assurance of shelf life and safety.

  6. Thermal, mechanics and electrical characterization of the Al-0,6%Mg-08%Si alloy refined and modified with different copper contents; Caracterizacao termica, mecanica e eletrica da liga Al-0,6% Mg-0,8% Si refinada e modificada com diferentes teores de cobre

    Energy Technology Data Exchange (ETDEWEB)

    Freitas, E.S. [Universidade Federal do Para (UFPA), Belem, PA (Brazil)], Email: mmanufreitas@gmail.com; Marques, P.R.R.; Santos, W.L.R.; Kamizono, K.A.; Quaresma, J. Maria V.

    2009-07-01

    The aluminum, magnesium and silicon alloys form a very important group, utilized as casted form and worked alloys, especially in 6201 alloy series. These alloys show applicability on cables and wires fabrication to electrical energy transmission. The present work analyzes the copper content variation and its influence in electrical conductivity, tensile strength and in studied alloy ductility. The refined Al-0,6% Mg-0,8% Si studied alloy was modified with the following contents: [0,05; 0,10; 0,20 e 0,30]% Cu and unidirectional solidified. The test specimen were machined to 10 mm diameter and rolled to 3,98 mm, whose deformation rate was 60,2%. The obtained wires were mechanical, electrical and structural characterized and the mechanical and electrical characterization results were associated to fractures of evaluated micro cavities. The highest observation was the Cu content in alloy increases the TS, decreases electrical conductivity and increases liquidus isotherm's velocity, forming micro cavities. (author)

  7. Synthesis and characterization of lanthanum manganite films for using in solid oxide fuel cells for operation at intermediate temperatures; Sintese e caracterizacao de filmes de manganita de lantanio para utilizacao em pilhas a combustivel de oxido solido para operacao em temperaturas intermediarias

    Energy Technology Data Exchange (ETDEWEB)

    Gama, L.M.; Paes Junior, H.R. [Laboratorio de Materiais Avancados - LAMAV - Universidade Estadual do Norte Fluminense - UENF, Campos dos Goytacazes, RJ (Brazil)

    2010-07-01

    This work aims to investigate the effects of doping and thermal processing of LaMnO{sub 3}, La{sub 0},{sub 8}Sr{sub 0},{sub 2}MnO{sub 3} e La{sub 0},{sub 8}Ca{sub 0},{sub 2}MnO{sub 3} films deposited by spray-pyrolysis technique on their structural, morphological and electrical properties, seeking its application as cathode in solid oxide fuel cells for operation in intermediate temperatures (IT-SOFC). These films were deposited on ferritic stainless steel type AISI 444. The thermal processing of the films was accomplished in air with treatment temperature of 900 degree or 1000 degree during 2 hours. The characterization by Xray diffraction revealed that the thermal processing propitiated the formation of the expected phases with the structure of perovskite. The analysis of surface morphology showed that doping provides an increase in porosity. Electrical characterization showed that Sr-doped films showed higher conductivity values and an activation energy of the conduction process of 0,41 eV. (author)

  8. Development and characterization of AlCrN coated Si{sub 3}N{sub 4} ceramic cutting tool; Desenvolvimento e caracterizacao de ferramentas ceramicas de Si{sub 3}N{sub 4} revestidas com AlCrN

    Energy Technology Data Exchange (ETDEWEB)

    Souza, J.V.C.; Nono, M.C.A.; Machado, J.P.B., E-mail: vitor@las.inpe.b [Instituto Nacional de Pesquisas Espaciais (INPE), Sao Jose dos Campos, SP (Brazil); Silva, O.M.M. [Centro Tecnico de Aeronautica (CTA-IAE/AMR), Sao Jose dos Campos, SP (Brazil). Inst. de Aeronautica e Espaco. Div. de Materiais; Pimenta, M. [Balzers, Jundiai, SP (Brazil); Sa, F.C.L. [Centro Universitario de Volta Redonda (UNIFOA), RJ (Brazil)

    2010-07-01

    Ceramic cutting tools are showing a growing market perspective in terms of application on machining operations due to their high hardness, wear resistance, and machining without a cutting fluid, therefore are good candidates for cast iron and Nickel superalloys machining. The objective of the present paper was the development of Si{sub 3}N{sub 4} based ceramic cutting insert, characterization of its physical and mechanical properties, and subsequent coating with AlCrN using a PVD method. The characterization of the coating was made using an optical profiler, XRD, AFM and microhardness tester. The results showed that the tool presented a fracture toughness of 6,43 MPa.m{sup 1/2} and hardness of 16 GPa. The hardness reached 31 GPa after coating. The machining tests showed an improvement on work piece roughness when machining with coated insert, in comparison with the uncoated cutting tool. Probably this fact is related to hardness, roughness and topography of AlCrN. (author)

  9. Synthesis and characterization of Zn{sub 2}SiO{sub 4} ceramic pigments obtained by chemical method; Sintese e caracterizacao de pigmentos ceramicos a base de Zn{sub 2}SiO{sub 4} obtidos por metodo quimico

    Energy Technology Data Exchange (ETDEWEB)

    Rangel, J.H.G.; Silva, J.S.; Oliveira, M.M.; Azevedo, E.; Costa, M.G.S., E-mail: hiltonrangel2012@hotmail.com [Instituto Federal do Maranhao (IFMA), Sao Luiz, MA (Brazil); Longo, E. [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Araraquara, UNESP, SP (Brazil). Instituto de Quimica

    2014-07-01

    The silicates provide a wide field of application, ranging from molecular sieves to catalyst supports, and therefore their morphology resulting from the obtaining method of production has been widely studied. The isomorphous replacement of cation Zn in the structure of willemite by a chromophore metal has been widely studied in the use of silicate as ceramic pigments. In this study the polymeric precursor was used to synthesize zinc silicates of nickel-doped to obtain ceramic pigments. The polymeric precursor was treated at 350 deg C/2h and the material was calcined at temperatures from 700 to 1000 deg C/4h on plates of sintered alumina at a heating rate of 10 deg C/min under ambient atmosphere in a muffle furnace type. The results of the XRD indicated the presence of the rhombohedral phase of the willemite and the presence of ZnO as an secondary phase. The micrographs, obtained by SEM, showed that the increasing in the temperature of calcination of the material from 700 to 1000 deg C caused an increasing in particle size due to the formation of aggregates. The reissue spectra of Kubelka-Munk measured by diffuse reflectance showed signs that suggest the presence of different cations in coordination. Based on the results obtained by means of colorimetric coordinates, it was observed that the material had bluish gray color. (author)

  10. Characterization of array scintillation detector for follicle thyroid 2D imaging acquisition using Monte Carlo simulation; Caracterizacao de uma matriz detectora cintiladora para aquisicao de imagem 2D da regiao folicular da glandula tireoide por emissao radioativa usando simulacao Monte Carlo

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Carlos Borges da

    2007-05-15

    The image acquisition methods applied to nuclear medicine and radiobiology are a valuable research study for determination of thyroid anatomy to seek disorders associated to follicular cells. The Monte Carlo (MC) simulation has also been used in problems related to radiation detection in order to map medical images since the improvement of data processing compatible with personnel computers (PC). This work presents an innovative study to find out the adequate scintillation inorganic detector array that could be coupled to a specific light photo sensor, a charge coupled device (CCD) through a fiber optic plate in order to map the follicles of thyroid gland. The goal is to choose the type of detector that fits the application suggested here with spatial resolution of 10 {mu}m and good detector efficiency. The methodology results are useful to map a follicle image using gamma radiation emission. A source - detector simulation is performed by using a MCNP4B (Monte Carlo for Neutron Photon transport) general code considering different source energies, detector materials and geometries including pixel sizes and reflector types. The results demonstrate that by using MCNP4B code is possible to searching for useful parameters related to the systems used in nuclear medicine, specifically in radiobiology applied to endocrine physiology studies to acquiring thyroid follicles images. (author)

  11. Development of an optimized algorithm for the characterization of microflow using speckle patterns present in optical coherence tomography signal; Desenvolvimento de um algoritimo otimizado para caracterizacao de fluxos microfluidicos utilizando padroes de speckle presentes no sinal de tomografia por coerencia optica

    Energy Technology Data Exchange (ETDEWEB)

    Pretto, Lucas Ramos de

    2015-07-01

    This work discusses the Optical Coherence Tomography system (OCT) and its application to the microfluidics area. To this end, physical characterization of microfluidic circuits were performed using 3D (three-dimensional) models constructed from OCT images of such circuits. The technique was thus evaluated as a potential tool to aid in the inspection of microchannels. Going further, this work paper studies and develops analytical techniques for microfluidic flow, in particular techniques based on speckle pattern. In the first instance, existing methods were studied and improved, such as Speckle Variance - OCT, where a gain of 31% was obtained in processing time. Other methods, such as LASCA (Laser Speckle Contrast Analysis), based on speckle autocorrelation, are adapted to OCT images. Derived from LASCA, the developed analysis technique based on intensity autocorrelation motivated the development of a custom OCT system as well as an optimized acquisition software, with a sampling rate of 8 kHz. The proposed method was, then, able to distinguish different flow rates, and limits of detection were tested, proving its feasibility for implementation on Brownian motion analysis and flow rates below 10 μl/min. (author)

  12. Synthesis and characterization of La{sub 1-x}Sr{sub x}MnO{sub 3} (x=0,1) for cathode application in solid oxide fuel cells (SOFC); Sintese e caracterizacao de La{sub 1-x}Sr{sub x}MnO{sub 3} (x=0,1) visando sua aplicacao como catodo em celulas a combustivel de oxido solido (SOFC)

    Energy Technology Data Exchange (ETDEWEB)

    Tarrago, D.P.; Sousa, V.C., E-mail: dptarrago@gmail.co [Universidade Federal do Rio Grande do Sul (LABIOMAT/PPGEM/UFRGS), Porto Alegre, RS (Brazil). Programa de Pos graduacao em Engenharia de Minas. Lab. de Biomateriais; Malfatti, C.F. [Universidade Federal do Rio Grande do Sul (LAPEC/PPGEM/UFRGS), Porto Alegre, RS (Brazil). Programa de Pos graduacao em Engenharia de Minas. Lab. de Pesquisa em Corrosao

    2010-07-01

    Perovskite powders, with composition La{sub 1-x}Sr{sub x}MnO{sub 3} (x=0,1) were obtained via combustion synthesis using sucrose as fuel. In the X-ray diffraction patterns it was observed that in order to obtain a single phase and well crystallized material a calcination in 750 deg C for 3 hours was necessary. BET analysis detected a specific surface area of 45m{sup 2}/g, considerably higher than when obtained with other fuels. SEM micrographs revealed a spongy aspect with a connected porosity in the agglomerates and though TEM micrographs the presence of pores in the particles was verified. The powder compacted with 125MPa and sintered at 1050 deg C for two hours presented a 31% open porosity and the SEM micrographs showed a fine interconnected porosity. (author)

  13. Synthesis and characterization of nanoparticles ferrites of the type ZN{sub x}Cu{sub 1-x}FE{sub 2}O{sub 4} and your application catalyst in acetylation vegetable oils; Sintese e caracterizacao de nanoparticulas de ferritas do tipo Zn{sub x}Cu{sub 1-x}Fe{sub 2}O{sub 4} e a sua aplicacao como catalisador em acetilacao em oleos vegetais

    Energy Technology Data Exchange (ETDEWEB)

    Casagrande, D.S; Costa, W.V; Hechenleitner, A.A.W.; Oliveira, D.M.F. de; Pineda, E.A.G., E-mail: diogo_casagrande@msn.com [Universidade Estadual de Maringa (UEM), PR (Brazil)

    2016-07-01

    In this work were synthesized copper and zinc ferrites (0 - 10% mol with respect to copper), by the combustion method, using citrate as stabilizer. The obtained products were analyzed by Infrared spectrometry (FTIR), Raman spectroscopy (RAMAN) and x-ray diffractometry (DRX). Synthesized ferrites present hematite phase, maghemite phase and copper ferrite phases. The analysis indicated that increasing the zinc content leads to decreased of hematite phase. Increasing of zinc content lead to an increase of particle size. The best results of oil acylation were obtained with ferrites containing 2 and 4% of zinc, wherein the increase the increase of yield of acetylated product reached at 19% when compared with the yield obtained whit copper ferrite without zinc. (author)

  14. Synthesis and characterization of CeO{sub 2} - TiO{sub 2} system for use in heterogeneous photocatalysis in photodegradation of methylene blue dye; Sintese e caracterizacao do sistema CeO{sub 2} - TiO{sub 2} para aplicacao em fotocatalise heterogenea na fotodegradacao do corante azul de metileno

    Energy Technology Data Exchange (ETDEWEB)

    Bragatto, Julia

    2016-07-01

    This study has as its goal the synthesis of a mixed oxide system type CeO{sub 2} - TiO{sub 2}, through the polymeric precursor method, to be used in heterogeneous photocatalysis. The synthesized materials were characterized by Thermogravimetry (TG), Derivative Thermogravimetry (DTG), Differential Thermal Analysis (DTA) and X-Ray Diffraction (XRD). The results of the thermal analysis showed in what temperature ranges certain events occur such as the formation of cerium oxide between 600 and 800 ° C, which refers to the crystallization of the material. Regarding the formation of titanium oxide, events between 600 and 800 ° C are perceived, which suggests the transformation of anatase to rutile phase. The XRD analysis showed no occurrence of the same phase for all materials, meaning that there is a variation in the formation of phases according to concentration of precursor for each sample. Noteworthy are the formation of CeO{sub 2} for Ce75-Ti25 and Ce50-Ti50 concentrations, with cubic crystal structure of the fluorite type. In Ce75-Ti25 and Ce25-Ti75 it is present the TiO{sub 2} in the anatase and rutile phase, with crystal structure of the tetragonal and tetrahedron type, respectively, as well as the formation of CeTi{sub 2}O{sub 6} in Ce50-Ti50 and Ce25-Ti75, with structure monoclinic. From these analyses, it is possible to see which samples, and in which temperatures of calcination the material has increased crystallinity, making the choice for their application in heterogeneous photocatalysis, aiming the degradation of methylene blue dye. Among the tested materials for methylene blue, the sample that stood out was the Ce50-Ti50, with calcination temperature of 800 °C, with values close to 50% degradation, because it was the sample that showed higher dye adsorption capacity, which is the step that precedes photodegradation. (author)

  15. Synthesis and characterization of nano structures of Silica SBA-16 containing Gadolinium-159 as potential nanoparticulated system for cancer therapy; Sintese e caracterizacao de nanoestruturas de Silica SBA-16 contendo Gadolinio-159 como potencial sistema nanoparticulado para o tratamento do cancer

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Andre Felipe de

    2013-07-01

    Cancer is a leading cause of death worldwide, and malignant neoplasms of the lung, stomach, liver, colon and breast in greater numbers. And recently observed in the literature a large number of reviews where new materials, especially nanoparticle, has been studied as drug carriers and radioisotopes applied to cancer treatment. How mesoporous materials based on silica, thanks to its huge surface area and biocompatibility, have been studied intensively providing broad applications in various areas, the use of nanostructured silica SBA-16 might be a carrier specific radioisotope accumulate in the cells malignant. Thus the aim of this study is to develop in vitro studies using SBA-16 can selectively concentrate in malignant cells therapeutic amounts of the radioisotope Gadolinium-159 escorting them to death. This work was performed orderly synthesis of mesoporous silica, SBA-16 and incorporating the complex Gd-DTPA-BMA, as well as chemical and structural characterization. The techniques used to analyze the occurrence of the incorporation of the gadolinium complex in the silica matrix were elemental analysis (CHN), atomic emission spectroscopy (ICP-AES), infrared spectroscopy (FTIR), nitrogen adsorption (BET), small-angle X-ray scattering (SAXS) and thermogravimetric analysis (TG). To analyze the morphology of pure silica used the scanning electron microscopy (SEM) and transmission electron microscopy (TEM). By photon correlation spectroscopy (PCS) it was possible to obtain a measure of mean particle size, the polydispersity index (PDI) of the silica SBA-16, and the zeta potential by laser Doppler anemometry (LDA). The results of incorporation analyzed by ICP-AES indicated that the material SBA-16 had a higher rate of incorporation of gadolinium (93%). The release kinetics in simulated body fluid, showed considerable stability and low release (1%). The mesoporous silica SBA-16 showed cell viability in direct contact with cell culture. Samples with gadolinium

  16. Promise Zones for Applicants

    Data.gov (United States)

    Department of Housing and Urban Development — This tool assists applicants to HUD's Promise Zone initiative prepare data to submit with their application by allowing applicants to draw the exact location of the...

  17. Learning Android application testing

    CERN Document Server

    Blundell, Paul

    2015-01-01

    If you are an Android developer looking to test your applications or optimize your application development process, then this book is for you. No previous experience in application testing is required.

  18. Connected vehicle applications : environment.

    Science.gov (United States)

    2016-01-01

    The U.S. Department of Transportation has developed a number of connected vehicle environmental : applications, including the Applications for the Environment Real-Time Information Synthesis (AERIS) : research program applications and road weather ap...

  19. Sight Application Analysis Tool

    Energy Technology Data Exchange (ETDEWEB)

    Bronevetsky, G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2014-09-17

    The scale and complexity of scientific applications makes it very difficult to optimize, debug and extend them to support new capabilities. We have developed a tool that supports developers’ efforts to understand the logical flow of their applications and interactions between application components and hardware in a way that scales with application complexity and parallelism.

  20. Activated carbon preparation with pore nanosized from biomass precursors; Preparacao de carvoes ativados com poros de dimensoes nanometricas a partir de precursores de biomassa

    Energy Technology Data Exchange (ETDEWEB)

    Capobianco, Gino [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Fac. de Engenharia Mecanica. Dept. de Planejamento de Sistemas Energeticos; Coutinho, Aparecido dos Reis [Universidade Metodista de Piracicaba, SP (Brazil). Lab. de Materiais Carbonosos; Luengo, Carlos Alberto [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Inst. de Fisica Gleb Wataghin. Grupo Combustiveis Alternativos

    2004-07-01

    Here are reported preliminary tests using pinnus wood, mesocarpo of green coconut and macadamia shell. They are carbonized and later physically activated with CO{sub 2} or chemically with ZnCl{sub 2}. The resulting activated carbons (AC) are characterized with scanning electronic microscopy, the BET method for determination of the specific surface area-ASE, real density-DR, helium picnometry among others. The results indicate macadamia shell originates better AC, with average micropores in the range of 1,2-1,6 nm, apparent density of 1,08 g/cm{sup 3}, and ASE-BET 1400m{sup 2}/g. Then, these AC have the possibility to be applied in NG storage. (author)

  1. Preparation of soda-lime glass using rock wool waste; Preparacao de vidros sodo-calcicos utilizando residuo de la de rocha

    Energy Technology Data Exchange (ETDEWEB)

    Aleixo, F.C.; Della, V.P. [Instituto Federal do Espirito Santo, Vitoria, ES (Brazil); Ballmann, T.J.S.; Folgueras, M.V. [Universidade do Estado de Santa Catarina (UESC), Joinville, SC (Brazil); Junkes, J.A., E-mail: janajunkes@gmail.com [Centro Universitario Tiradentes, Maceio, AL (Brazil)

    2016-10-15

    Discarded by the mining industry during the maintenance stoppages of pelletizing furnaces, rock wool has in its composition SiO{sub 2} (56%), Na{sub 2} O (12%) and CaO (7%) propitious for obtaining soda-lime glasses. Under this focus, this work developed soda-lime glasses formulations, using as main raw-material rock wool waste in proportions from 50 to 100% by adjusting the chemical composition of the formulations with sand, sodium and calcium carbonates, as silica, soda and lime sources, respectively. In some formulations the sodium carbonate was replaced by sodium sulfate, which acts as a refining agent, improving homogenization and reducing the bubble formation during the melting. Initially, the raw-materials were evaluated by X-ray fluorescence, X-ray diffraction, differential thermal analysis, and thermogravimetric analysis. The tests showed that the rock wool waste has potential to be used in soda-lime glasses production, however, the chemical composition must be corrected. After knowing the waste potential, seven mixtures were prepared and molten at 1550 °C for 1 to 2 h. It has been found that the maximum rock wool waste percentage that can be used is between 60 and 80%, and that the 2 h melting time resulted in more homogeneous glasses and fewer bubbles according to the addition of sodium sulfate which is efficient for bubbles removal. (author)

  2. Preparation of membranes from cellulose obtained of sugarcane bagasse; Preparacao de membranas a partir de celulose obtida do bagaco de cana-de-acucar

    Energy Technology Data Exchange (ETDEWEB)

    Pereira, Paulo Henrique Fernandes; Cioffi, Maria Odila Hilario; Voorwald, Herman Jacobus Cornelis, E-mail: fernandes_eng@yahoo.com.b [UNESP, Guaratingueta, SP (Brazil). Fac. de Engenharia; Pinho, Maria Noberta de [Instituto Superior Tecnico de Lisboa (IST) (Portugal), Dept. de Engenharia; Silva, Maria Lucia Caetano Pinto da [Universidade de Sao Paulo (EEL/USP), Lorena, SP (Brazil). Escola de Engenharia

    2010-07-01

    In this work, cellulose obtained from sugarcane bagasse to produce both cellulose and acetylated cellulose to prepare asymmetric membranes. Membranes was procedure used a mixture of materials of DMAc/ LiCl systemic in different conditions. Cellulose and acetylated cellulose were characterized by thermogravimetric (TG), Xray diffraction (XRD) and scanning Electron Microscopy (SEM). Observed less stability thermal of acetylated cellulose when compared of cellulose. All membranes procedure were asymmetric, characterized by presence of a dense skin and porous support can be observed. SEM showed that the morphology of the superficial of membranes depends on the method preparation. (author)

  3. Procedure for lichen sample preparation for neutron activation analysis; Procedimento para preparacao de amostras de liquens para analise por ativacao com neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Aguiar, Larissa R. [Faculdades Oswaldo Cruz, Sao Paulo, SP (Brazil)]. E-mail: lraguiar@ipen.br; Alves, Edson R.; Saiki, Mitiko [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)]. E-mail: eralves@ipen.br; mitiko@ipen.br

    2007-07-01

    This paper presents the procedures established for collection and preparation of lichen samples for determination of chemical elements by using the neutron activation analysis (NAA). The concentration of Ba, Br, Cr, Fe, K, Na, Rb and Zn were obtained at levels of mg kg{sub 1}, and the elements As, Co, Cs, La, Sb, Sc and Se at levels of {mu}g kg{sub 1}, and the Ca at levels or percentages. Good re plicata analysis results were obtained. The reference material IAEA 336 Lichen were analysed for the quality control of the analytical results. (author)

  4. Preparation of association compound between rhodium(II) citrate and {beta}-cyclodextrin; Preparacao do composto de associacao entre citrato de rodio(II) e {beta}-ciclodextrina

    Energy Technology Data Exchange (ETDEWEB)

    Burgos, Ana E.; Okio, Coco K.Y.A., E-mail: aeburgosc@unal.edu.co [Departamento de Quimica, Universidad Nacional de Colombia, Bogota (Colombia); Sinisterra, Ruben D. [Departamento de Quimica, Instituto de Ciencias Exatas, Universidade Federal de Minas Gerais, Belo Horizonte - MG (Brazil)

    2012-07-01

    Inclusion compound of rhodium(II) citrate with{beta}-cyclodextrin in a 1:1 molar ratio was prepared using freeze-drying method. X-ray diffractometry, thermal analysis (TG/DTG/DSC), infrared and {sup 1}H-NMR with {sup 1}H spin lattice relaxation ({sup 1}H T{sub 1}) measurements and {sup 13}C techniques were used to characterize the system prepared. The results indicated the formation of inclusion or association compounds between rhodium(II) citrate and {beta}-cyclodextrin. (author)

  5. Preparation and performance of Ecobras/bentonite biodegrading films; Preparacao e desempenho de filmes polimericos biodegradaveis a base de Ecobras e bentonita

    Energy Technology Data Exchange (ETDEWEB)

    Costa, Ana Nery M.; Melo, Nadja M.C.; Canedo, Eduardo L.; Carvalho, Laura H., E-mail: laura@dema.ufcg.edu.br [Unidade Academica de Engenharia de Materiais, Universidade Federal de Campina Grande (UAEMa/UFCG) Campina Grande, PB (Brazil); Araujo, Arthur R.A. [Felinto Industria e Comercio Ltda., Campina Grande, PB (Brazil)

    2011-07-01

    Compounds based on the biodegradable polymer Ecobras and bentonite clay in its pristine, sonicated, and organically modified with a quaternary ammonium salt forms were prepared as flat films. Clays and compounds were characterized by x-ray diffraction and scanning electron microscopy. Mechanical properties of the films were determined according to pertinent ASTM standards. Reasonable properties, higher than those of the matrix, were obtained with compounds prepared with purified clays and organoclays, particularly for low clay loading. (author)

  6. Preparation of mixed oxides (Th,U)O{sub 2}: an evaluation of different techniques; Estudos de diferentes rotas de preparacao de oxidos binarios de torio e uranio

    Energy Technology Data Exchange (ETDEWEB)

    Ayoub, Jamil Mahmoud Said

    1999-07-01

    An evaluation of different ways of obtaining (Th-U)O{sub 2} mixed oxides is described. Coprecipitation, mechanical mixing of uranium and thorium powders, and the sol-gel technique were studied in order to get a large spectrum of knowledge of the process performance. The use of ultrasonic waves for the homogenization of the hydroxide mixture and microwave heating for powder drying was also investigated. Sol-gel showed the best results regarding the specific area for obtained samples. Oxide drying by microwave is an effective method to get mixed oxides for fuel fabrication. Neither coprecipitation nor mechanical mixing of the thorium and uranium oxide powders is suitable for the purpose. The obtained data are less than 70% than those achieved when sol-gel process is performed. Electronic microscopy, X-ray fluorescence and diffraction, thermogravimetry, specific gravidity and specific area determination (BET) used for sample characterization were convenient and accomplished good results. (author)

  7. Preparation of PVDF and PTFE membranes for fuel cell use; Preparacao de membranas de PVDF e PTFE enxertadas e sulfonadas para uso em celula a combustivel

    Energy Technology Data Exchange (ETDEWEB)

    Geraldes, Adriana N.; Zen, Heloisa A.; Ferreira, Henrique P.; Parra, Duclerc F.; Lugao, Ademar B.; Linardi, Marcelo [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)], e-mail: angeral@ipen.br

    2007-07-01

    Grafting of styrene onto polyvinylidenefluoride (PVDF), polytetrafluoroethylene (PTFE) was studied using styrene/toluene solutions. First, PTFE and PVDF films were prepared and the process was conducted by radiation induced graft polymerization of styrene, by a Co{sup 60} source. Films of PTFE and PVDF were immersed in styrene/toluene at 1:1 (v/v) concentration and then submitted to gamma radiation at 20 kGy doses. After irradiation, the samples were evaluated at the period of 21 days at room temperature in order to observe the grafting degree. Chemical changes in the PVDF and PTFE films after styrene grafting were monitored and the results were evaluated by FTIR, DSC, TGA and degree of grafting (DOG). The ion exchange capacity (IEC) after sulfonation of 1, 2 and 24 hours were also determined. (author)

  8. Preparation of hard magnetic materials based on nitrogenated rare-earth iron alloys; Preparacao de materiais magneticamente duros a base de ligas de terra rara - ferro nitrogenadas

    Energy Technology Data Exchange (ETDEWEB)

    Guilherme, Eneida da Graca

    1999-07-01

    Nd Fe{sub 11}Ti, Nd Fe{sub 10.5} Mo{sub 1.5} and Nd Fe{sub 10.75} Mo{sub 1.25} alloys were synthesized by reduction-diffusion calciothermic process (RDC) from neodymium chloride (NdCl{sub 3}), iron, titanium, molybdenum and reduction agent (metallic calcium). The effect of process variables, like temperature, time, excess amount of NdCl{sub 3}, heating rate, and composition variation of the Nd Fe{sub 12-x}Mo{sub x} (1 {>=} x {>=} 2). Mother alloys in which 1:12 phase is major were nitrogenated by gas-solid reaction with N{sub 2} and by chemical reaction with sodium zide (Na N{sub 3}). In addition, the influence of reducing particle size of the powdered mother alloys in the nitrogenation step with Na N{sub 3} were studied. As prepared and interstitially modified Nd Fe{sub 11} Ti, Nd Fe{sub 10.5} Mo{sub 1.5} and Nd Fe{sub 10.75} Mo{sub 1.25} alloys with nitrogen , were characterized by X-ray diffraction, Moessbauer spectroscopy, thermomagnetic, SEM and EDS. Nitrogenation by gas-solid reaction with N{sub 2} is found to be not promising, since resulted Curie temperatures (Tc) were lower than literature values. However, nitrogenation by chemical reaction with Na N{sub 3} was efficient with higher or same Tc than previous reported results. The average increases on Tc and volumetric expansion were 200 deg C and 4%, respectively. Milling of the mother alloys before nitrogenation at 330 deg C is preferred because reaction kinetics is enhanced. Nevertheless, at 450 deg C, a competition between the interstitially modified compound formation (alloy + N) and alloy dissociation has occurred, resulting in a Fe-{alpha} phase increase. (author)

  9. Study of preparation and surface morphology of self-ordered nanoporous alumina; Estudo da preparacao e da morfologia de superficie de alumina nanoporosa auto-organizada

    Energy Technology Data Exchange (ETDEWEB)

    Rodrigues, Elisa Marchezini; Martins, Maximiliano Delany, E-mail: elisamarch@gmail.com, E-mail: MG.mdm@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG. (Brazil); Silva, Ronald Arreguy, E-mail: arregsilva@yahoo.com.br [Centro Universitario de Belo Horizonte (UniBH), Belo Horizonte, MG (Brazil)

    2013-07-01

    Nanoporous alumina is a typical material that exhibits self-ordered nanochannels spontaneously organized in hexagonal shape. Produced by anodizing of metallic aluminum, it has been used as a template for production of materials at the nanoscale. This work aimed to study the preparation of nanoporous alumina by anodic anodizing of metallic aluminum substrates. The nanoporous alumina was prepared following the methodology proposed by Masuda and Fukuda (1995), a two-step method consisting of anodizing the aluminum sample in the potentiostatic mode, removing the layer of aluminum oxide (alumina) formed and then repeat the anodization process under the same conditions as the first anodization. This method produces nanoporous alumina with narrow pore diameter distribution and well-ordered structure. (author)

  10. Processes of preparation, deposition and analysis of thermionic emissive substances; Processos de preparacao, deposicao e analise de substancias emissoras de eletrons

    Energy Technology Data Exchange (ETDEWEB)

    Romao, B.M. Verdelli; Muraro Junior, A.; Tessaroto, L.A.B. [Centro Tecnico Aeroespacial (CTA-IEAv), Sao Jose dos Campos, SP (Brazil). Inst. de Estudos Avancados; Takahashi, J. [Sao Paulo Univ., SP (Brazil). Inst. de Fisica

    1992-09-01

    This paper shows the results of the optimization of the process of preparation and deposition of thermionic emissive substances that are used in the oxide-cathodes which are utilized in the gun of the IEAv linear electron accelerator. (author). 5 refs., 5 figs.

  11. Microwave power engineering applications

    CERN Document Server

    Okress, Ernest C

    2013-01-01

    Microwave Power Engineering, Volume 2: Applications introduces the electronics technology of microwave power and its applications. This technology emphasizes microwave electronics for direct power utilization and transmission purposes. This volume presents the accomplishments with respect to components, systems, and applications and their prevailing limitations in the light of knowledge of the microwave power technology. The applications discussed include the microwave heating and other processes of materials, which utilize the magnetron predominantly. Other applications include microwave ioni

  12. Web applications quality assessment

    OpenAIRE

    Tamulynaitė, Donaira

    2017-01-01

    Web applications are becoming more and more popular. Web application quality may determine its success, however, there is no one generally accepted standard or quality model for web applications quality evaluation. The aim of this thesis is to provide a quality model for web applications. The constructed quality model is based on ISO Systems and software Quality evaluation standard, as well as on theoretical research results analysed in this topic. 18 web application characteristics have been...

  13. Ruby on Rails Applications

    Science.gov (United States)

    Hochstadt, Jake

    2011-01-01

    Ruby on Rails is an open source web application framework for the Ruby programming language. The first application I built was a web application to manage and authenticate other applications. One of the main requirements for this application was a single sign-on service. This allowed authentication to be built in one location and be implemented in many different applications. For example, users would be able to login using their existing credentials, and be able to access other NASA applications without authenticating again. The second application I worked on was an internal qualification plan app. Previously, the viewing of employee qualifications was managed through Excel spread sheets. I built a database driven application to streamline the process of managing qualifications. Employees would be able to login securely to view, edit and update their personal qualifications.

  14. Characterization of grog of bricks; Caracterizacao de chamote de blocos de vedacao

    Energy Technology Data Exchange (ETDEWEB)

    Candido, V.S.; Pinheiro, R.M.; Monteiro, S.N.; Vieira, C.M.F. [Universidade Estadual do Norte Fluminense Darcy Ribeiro (LAMAV/CCT/UENF), Campos dos Goytacazes, RJ (Brazil). Lab. de Materiais Avancados

    2010-07-01

    This work aims to characterize a waste of red ceramic, grog, generated from the milling of defective pieces of bricks fired in a Hoffmann type furnace by a industry from Campos dos Goytacazes-RJ. The grog was tested for X-ray diffraction, X-ray fluorescence, thermogravimetric and differential thermal analysis, dilatometry, sieving and sedimentation by gravity and optical microscopy. The results indicated that the grog is predominantly constituted of quartz, muscovite mica and hematite. The presence of kaolinite indicates that the bricks were fired at low temperatures, below 600 deg C. Finally, the characterization results indicated that the grog presents itself as an alternative non plastic material to be used in mixtures with clays for the production of red ceramics. (author)

  15. Characterization of experimental cements with endodontic goal; Caracterizacao de cimentos experimentais com finalidade endodontica

    Energy Technology Data Exchange (ETDEWEB)

    Dantas, A.M.X.; Sousa, W.J.B.; Oliveira, E.D.C.; Carrodeguas, R.G.; Fook, M.V. Lia, E-mail: alana.mxd@hotmail [Universidade Federal de Campina Grande (CCT/UFCG), PB (Brazil). Unidade Academica de Engenharia de Materiais; Universidade Estadual da Paraiba (UEPB), Campina Grande, PB (Brazil). Departamento de Quimica

    2017-10-01

    The present study aimed to characterize experimental endodontic cements using as comparative parameter MTA cement. Two experimental endodontic cements were assessed: one based on 95% tri-strontium aluminate and 5% gypsum (CE1) and another based on 50% Sr{sub 3}Al{sub 2}O{sub 6} and 50% non-structural white cement (CE2). Experimental cements were manipulated and characterized by scanning electron microscopy (SEM), coupled to EDS mode, X-ray diffractometer (XRD) and Thermogravimetric (TG) analysis. Data analysis demonstrated that the particles of the materials used presented varied shapes and sizes, with similar elements and crystalline behavior. However, CE1 presented increased mass loss. Experimental cements presents similarities to MTA, nevertheless, further studies are encourage to determinate comparative properties with the commercially material. (author)

  16. Magnetic ionic liquids: synthesis and characterization; Liquidos ionicos magneticos: sintese e caracterizacao

    Energy Technology Data Exchange (ETDEWEB)

    Medeiros, Anderson M.M.S.; Parize, Alexandre L.; Oliveira, Vanda M.; Neto, Brenno A.D.; Rubim, Joel C. [Universidade de Brasilia (LMC/IQ/UnB), DF (Brazil). Inst. de Quimica. Lab de Materiais e Combustiveis

    2010-07-01

    The synthesis of magnetic ionic liquids (MILs) based on the stable dispersions of magnetic nanoparticles (MNPs) of {gamma}-Fe{sub 2}O{sub 3}, Fe{sub 3}O{sub 4}, and CoFe{sub 2}O{sub 4} in the ionic liquid 1-n-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide (BMI.NTf{sub 2}) is reported. The MNPs were obtained by the coprecipitation method. The surface of the {alpha}-Fe{sub 2}O{sub 3}, Fe{sub 3}O{sub 4}, and CoFe{sub 2}O{sub 4} MNPs with mean sizes (XRD) of 9.3, 12.3, and 11.0 nm, respectively were functionalized by 1-n-butyl-3-(3'-trimethoxypropylsilane)- imidazolium chloride. The non functionalized and functionalized MNPs were further characterized by Raman, FTIR-ATR, and FTNIR spectroscopy and by TGA. The stability of the MILs was assigned to the formation of at least one monolayer of the surface modifier agent that mimics the structure of the BMI.NTf{sub 2} IL. (author)

  17. Synthesis and characterization of metallic nuclear fuels; Sintese e caracterizacao de combustiveis nucleares metalicos

    Energy Technology Data Exchange (ETDEWEB)

    Longen, F.R., E-mail: frlongen@utfpr.edu.br [Universidade Tecnologica Federal do Parana (UTFPR), Medianeira, PR (Brazil); Barco, R.; Paesano Junior, A. [Universidade Estadual de Maringa (UEM), PR (Brazil); Pagano Junior, L. [Centro Tecnologico da Marinha (CETEM), Sao Paulo, SP (Brazil)

    2014-07-01

    U-Zr-Mo and U-Zr-Gd ternary alloys, potentially useful as metallic nuclear fuel, were prepared at different concentrations by arc-melting and characterized by X-ray diffraction. Those alloys containing molybdenum were submitted to thermal annealing in inert atmosphere, followed by quenching in water. These samples were measured before and after the thermal treatment. The diffractometric results evidenced that the as-cast alloys solidified mostly with a body centered cubic structure (γphase) and that for the uranium richest samples a second phase formed, with an orthorhombic structure (α phase). For the U-Zr-Gd alloys the X-ray diffractometry revealed the retention of a hexagonal structure (δ phase) and gadolinium traces in the poorest uranium samples. The U{sub 57}(Zr{sub 92}Gd{sub 8}){sub 43} sample resulted monophasic becoming, according to literature, the first time that a solid solution combining uranium and gadolinium is identified. (author)

  18. Characterization of caroa fiber (Neoglaziovia variegata); Caracterizacao de fibras de caroa (Neoglaziovia variegata)

    Energy Technology Data Exchange (ETDEWEB)

    Sales, J.C. de; Matos, C.F.; Miranda, C.S.; Guimaraes, D.H.; Goncalves, A.P.B.; Jose, N.M., E-mail: joed_salles@hotmail.com [Universidade Federal da Bahia (GECIM/UFBA), Salvador, BA (Brazil). Grupo de Energia e Ciencias dos Materiais

    2014-07-01

    The use of lignocellulosic fibers as reinforcement in polymeric materials to replace synthetic fibers, have been expanded, since several studies show that they have comparable mechanical, physical and chemical properties of the synthetic reinforcements. The caroa (Neoglaziovia variegata) is a plant in the bromeliad family (family Bromeliaceae), that occurs in semi-arid region. The fibers, which are extracted from its leaves are thin and bright and are used by people for making nets, bags and twine. This study aimed to characterize by SEM, DSC, TGA, XRD and density, caroa fibers in natura and treated with a solution of 5% sodium hydroxide for 1 h at room temperature. The mercerization promoted cleaning of the surface dirt, waxes and partial removal of hemicellulose and lignin. The thermal analysis showed characteristic events of the main constituents (lignin, hemicellulose and cellulose). The main event of decomposition occurs at a temperature around 330 ° C. (author)

  19. Bio-inspired synthesis and characterization of superparamagnetic particles; Sintese e caracterizacao bioinspirada de particulas superparamagneticas

    Energy Technology Data Exchange (ETDEWEB)

    Castro, Vinicius F., E-mail: vfc_mg@yahoo.com.br [Universidade Federal de Itajuba (UNIFEI), MG (Brazil); Queiroz, Alvaro A.A. [Universidade Federal de Itajuba (UNIFEI), MG (Brazil). Centro de Estudos e Inovacao em Materiais Biofuncionais Avancados

    2012-08-15

    This paper discusses the bio-inspired synthesis of type YFeAl ferrites encapsulated into polyglycerol dendrimers (PGLD) generation 3. The structure and morphological properties of the system YFeAl/PGLD was characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The magnetic properties were studied through the techniques of Moessbauer spectroscopy and magnetization. The cytotoxicity of the nanoparticles encapsulated in dendrimers PGLD G3 at the cell membrane was studied against mammalian cell line CHO.K1 measuring the amount of lactate dehydrogenase (LDH) released by the cell damage. Microscopy TEM and XRD analysis indicate that spherical nanoparticles were obtained highly crystalline and monodisperse with size 20 nm

  20. Thermodegradation of biodiesel: thermoanalytical and rheological characterization; Degradacao termica de biodiesel: caracterizacao termoanalitica e reologica

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Everson L.; Carvalho, Laura H.; Araujo, Gilmar T.; Gadelha, Tatiana S. [Universidade Federal de Campina Grande (UFCG), PB (Brazil)

    2008-07-01

    Brazil is a country of extensive agricultural land and great oil consumption and these factors favor biodiesel production in this country. In order for diesel/biodiesel mixtures to be effectively employed in diesel engines, a rigid quality control of these mixtures is needed. Biodiesel and mixtures must have their quality monitored with respect to oxidative resistance, thermal stability, fluidity and volatility, properties which can be modified by the adverse transport and stock conditions prior to consumption. Oxidation is the main degradation mechanism of products under transport and stock conditions, which can lead to significant economical losses. In this work sought the thermal degradation of neat biodiesel, synthesized in our laboratories was monitored. Thermal aging was conducted at 210 deg C for up to 1000 h. Virgin and thermally degraded samples were characterized by rheological measurements (in different shear conditions); FTIR; density and by color changes. We concluded that the soy biodiesel was successfully synthesized and that thermal exposure caused thermal-oxidative degradation of the biodiesel sample, significantly changing its properties as a function of thermal exposure times. (author)

  1. Surface characterization of titanium based dental implants; Caracterizacao de implantes odontologicos a base de titanio

    Energy Technology Data Exchange (ETDEWEB)

    Castilho, Guilherme Augusto Alcaraz

    2006-07-01

    Dental implantology uses metallic devices made of commercially pure titanium in order to replace lost teeth. Titanium presents favorable characteristics as bio material and modern implants are capable of integrate, witch is the union between bone and implant without fibrous tissue development. Three of the major Brazilian implant manufacturers were chosen to join the study. A foreign manufacturer participated as standard. The manufacturers had three specimens of each implant with two different surface finishing, as machined and porous, submitted to analysis. Surface chemical composition and implant morphology were analyzed by X-ray photoelectron spectroscopy (XP S), scanning electron microscopy (SEM) and microprobe. Implant surface is mainly composed of titanium, oxygen and carbon. Few contaminants commonly present on implant surface were found on samples. Superficial oxide layer is basically composed of titanium dioxide (TiO{sub 2}), another oxides as Ti O and Ti{sub 2}O{sub 3} were also found in small amount. Carbon on implant surface was attributed to manufacturing process. Nitrogen, Phosphorous and Silicon appeared in smaller concentration on surface. There was no surface discrepancy among foreign and Brazilian made implants. SEM images were made on different magnification, 35 X to 3500 X, and showed similarity among as machined implants. Porous surface finishing implants presented distinct morphology. This result was attributed to differences on manufacturing process. Implant bioactivity was accessed through immersion on simulated body solution (SBF) in order to verify formation of an hydroxyapatite (HA) layer on surface. Samples were divided on three groups according to immersion time: G1 (7 days), G2 (14 days), G3 (21 days), and deep in SBF solution at 37 deg C. After being removed from solution, XPS analyses were made and then implants have been submitted to microprobe analysis. XPS showed some components of SBF solution on sample surface but microprobe examinations did not confirmed the formation of HA layer. However, it was observed NaCl crystals on some implant surface. (author)

  2. Hydrogeological characterization of Itataia mine, Ceara, Brazil; Caracterizacao hidrogeologica da jazida de Itataia, CE

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Jose Roberto de Alcantara e

    2003-07-01

    This work analyzes the geological-geotechnical-geophysical behavior, aiming to define the characteristics of a karstic-fissural aquifer in the mid-northern region of the State of Ceara, named as Itataia Phosphor-Uranium Deposit. This area is constituted of marbles and gneisses from Itataia Group, which are morphologically located at a higher point to the south and at a lower point to the north, related to Paleoproterozoic Era. Fracture system led to the implantation of two karstic marble phases, being the oldest from Cambrian Period and the most recent from Tertiary/Quaternary Period. Porosity is secondary to fractures, fissures and crushed zones which act as hydraulic channels for groundwater flow. Major geophysics defined conducting lines are controlled by normal fractures and faults in both N70 deg E and N80 deg W directions, and secondarily in both N10 deg E and N30 deg W directions, dipping 70 deg -85 deg into the northern quadrant of the main axes. Fault characteristics are typical of graben and horst patterns. Rocks in the area are distributed into three classes of geotechnical massif: healthy rock, moderately altered and fractured rock, and strongly altered and fractured rock. The latter occurs predominantly in the center of the area, from the soil surface to an average depth of 150 meters. Groundwater flow is characterized by fractures which enlarged by the karstic phenomenon dissolution, and then become closer as deeper they are. This flow may be slower or even discontinue in light of silty-argillaceous alteration material that fill the open fracture gaps. Water level is not lower than 5 m or higher than 90 m, averaging by 30 m ali over the area. The synoptic piezometry map shows a general south-north direction; however in the southwestern portion - the recharge zone - it takes the south direction, while in the southeastern portion it takes the southeast direction. (author)

  3. Naphthenic acid characterization and distribution in crude oils; Caracterizacao e distribuicao de acidos naftenicos em petroleos

    Energy Technology Data Exchange (ETDEWEB)

    Guimaraes, Regina C.L.; Gomes, Alexandre de O. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil)

    2008-07-01

    Naphthenic acid corrosion was observed for the first time during the distillation process of some kind of crude oils in 1920. Recent reports about naphthenic acid corrosion have been found in China, India, Venezuela, Eastern Europe, Russia and the USA. In Brazil, heavy and acid crude oil processing is rising. Some brazilian crude oils have TAN around 3,0 mg KOH/g. The presence of relatively high levels of naphthenic acids in crude oils is a bane of petroleum refiners; and more recently, of producers as well, who have reported problems during production with calcium and sodium naphthenate . Essentially, these acids which are found to greater or lesser extent in virtually all crude oils are corrosive and tend to cause equipment failures, lead to high maintenance costs and may pose environmental disposal problems. In order to give these information to PETROBRAS, The Research and Development Center of PETROBRAS (CENPES) has been working in house and with brazilian universities developing analytical technicians to know better molecular structures and distribution of these acids compounds in crude oils. This work presents the actual methods and some results from these developments. (author)

  4. Characterization of hydroxyapatite substituted with silicon; Caracterizacao de hiroxiapatita substituida com silicio

    Energy Technology Data Exchange (ETDEWEB)

    Silva, H.M. da; Soares, G.A., E-mail: helena@metalmat.ufrj.b [Universidade Federal do Rio de Janeiro (COPPE/UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao em Engenharia. Lab. de Biomateriais para Engenharia Ossea; Mateescu, M.; Anselme, K. [Universite de Haute-Alsace (UHA/IS2M), Mulhouse (France). Inst. de Science des Materiaux; Palard, M.; Champion, E. [Universite de Limoges (France). Fac. des Sciences et Techniques

    2009-07-01

    Incorporation of silicon (Si) ions into hydroxyapatite structure (HA) influences on physical, chemical and physiological properties. Some studies reported the improved bioactivity Si substitution, and it also accelerates the biomineralization process. The main objective of this work is to characterize stoichiometric hydroxyapatite and hydroxyapatite substituted with 1.13% in weight of Si (SiHA) using a wet precipitation method followed by a heat treatment. SEM/EDS, AFM, DRX and FTIR analyses were used to characterize the samples. EDS and FTIR results confirmed the presence of Si. Silicon induces small changes on crystal structure of HA, not detected on X-ray diffraction patterns of sintered tablets of SiHA and HA. No secondary phases were observed, that indicates the Si had entered the HA lattice. (author)

  5. Engineering Adaptive Applications

    DEFF Research Database (Denmark)

    Dolog, Peter

    . The different requirements might be satisfied by different variants of features maintained and provided by Web applications. An adaptive Web application can be seen as a family of Web applications where application instances are those generated for particular user based on his characteristics relevant...... for a domain.In this book, we propose a new domain engineering framework which extends a development process of Web applications with techniques required when designing such adaptive customizable Web applications. The framework is provided with design abstractions which deal separately with information served...

  6. Apprehensive about applications

    International Nuclear Information System (INIS)

    Anon.

    1989-01-01

    Current predictions for high Tc applications range from six months to twenty years, depending on the application. Many companies are also understandably reluctant to discuss the progress of proprietary work, which in all probability means that they are close to being able to produce a final product. Many researchers are claiming that they will have device applications ready in one to two years. But these applications will be demonstration prototypes and most will take many more years of engineering before they will become commercially viable applications, at which point they become dependant on economic factors, not performance factors, for their ultimate acceptance or ejection by the commercial marketplace. As in low Tc superconductivity, economics, not performance, may determine which applications are eventually successful. Military applications are discussed as being the first which will utilize high Tc materials, primarily through SQUIDS. Other possible applications, including electronics, wires, and microwave devices, are addressed

  7. AHA: Anagram Hashing Application

    NARCIS (Netherlands)

    Reynaert, Martin; Borin, Lars

    2016-01-01

    We briefly present AHA, the Anagram Hashing Application, a new web application and service that allows researchers to effortlessly analyse the lexical variation present in their Gold Standard data and to publish the results.

  8. Connected vehicle applications : safety.

    Science.gov (United States)

    2016-01-01

    Connected vehicle safety applications are designed to increase situational awareness : and reduce or eliminate crashes through vehicle-to-infrastructure, vehicle-to-vehicle, : and vehicle-to-pedestrian data transmissions. Applications support advisor...

  9. Applicant Satisfaction Survey

    Data.gov (United States)

    Office of Personnel Management — The Chief Human Capital Officers developed 3 surveys that asks applicants to assess their satisfaction with the application process on a 1-10 point scale, with 10...

  10. Biomedical Applications of Graphene

    Science.gov (United States)

    Shen, He; Zhang, Liming; Liu, Min; Zhang, Zhijun

    2012-01-01

    Graphene exhibits unique 2-D structure and exceptional phyiscal and chemical properties that lead to many potential applications. Among various applications, biomedical applications of graphene have attracted ever-increasing interests over the last three years. In this review, we present an overview of current advances in applications of graphene in biomedicine with focus on drug delivery, cancer therapy and biological imaging, together with a brief discussion on the challenges and perspectives for future research in this field. PMID:22448195

  11. Nanoplasmonics advanced device applications

    CERN Document Server

    Chon, James W M

    2013-01-01

    Focusing on control and manipulation of plasmons at nanometer dimensions, nanoplasmonics combines the strength of electronics and photonics, and is predicted to replace existing integrated circuits and photonic devices. It is one of the fastest growing fields of science, with applications in telecommunication, consumer electronics, data storage, medical diagnostics, and energy.Nanoplasmonics: Advanced Device Applications provides a scientific and technological background of a particular nanoplasmonic application and outlines the progress and challenges of the application. It reviews the latest

  12. SIMS applications workshop. Proceedings

    International Nuclear Information System (INIS)

    1997-04-01

    The first ANSTO/AINSE SIMS Workshop drew together a mixture of Surface Analysis experts and Surface Analysis users with the concept that SIMS analysis has to be enfolded within the spectrum of surface analysis techniques and that the user should select the technique most applicable to the problem. With this concept in mind the program was structured as sessions on SIMS Facilities; Applications to Mineral Surfaces; Applications to Biological Systems, Applications to Surfaces as Semi- conductors, Catalysts and Surface Coatings; and Applications to Ceramics

  13. SNS application programming plan

    International Nuclear Information System (INIS)

    Chu, C.M.; Galambos, J.D.; Wei, J.; Allen, C.; McGehee, P.M.; Malitsky, N.

    2001-01-01

    The plan for Spallation Neutron Source accelerator physics application programs is presented. These high level applications involve processing and managing information from the diagnostic instruments, the machine control system, models and static databases and will be used to investigate and control beam behavior. Primary components include an SNS global database and Java-based XAL Application Toolkit. A key element in the SNS application programs is time synchronization of data used in these applications, due to the short pulse (1 ms), pulsed (60 Hz) nature of the device. The data synchronization progress is also presented.

  14. Criteria for Social Applications

    DEFF Research Database (Denmark)

    Atzenbeck, Claus; Tzagarakis, Manolis

    2007-01-01

    relationships between individuals thus creating social networks. Although Web 2.0 applications are a popular and characteristic class of such applications they are not the only representatives that permit such functionality. Applications in the Personal Information Management domain exhibit similar......Social networks are becoming increasingly important for a wide number of applications. This is in particular true in the context of the Web 2.0 movement where a number of Web-based applications emerged - termed social networking applications or services - that allow the articulation of social...... characteristics but have never been mentioned in the context of social networking. The increasing number and diversity of such applications makes their study, analysis and evaluation from a systems point of view critical and important as their study may help identify relationships that are useful when attempting...

  15. Electronic Submissions of Pesticide Applications

    Science.gov (United States)

    Applications for pesticide registration can be submitted electronically, including forms, studies, and draft product labeling. Applicants need not submit multiple electronic copies of any pieces of their applications.

  16. Technical applications of aerogels

    International Nuclear Information System (INIS)

    Hrubesh, L.W.

    1997-01-01

    Aerogel materials posses such a wide variety of exceptional properties that a striking number of applications have developed for them. Many of the commercial applications of aerogels such as catalysts, thermal insulation, windows, and particle detectors are still under development and new application as have been publicized since the ISA4 Conference in 1994: e.g.; supercapacitors, insulation for heat storage in automobiles, electrodes for capacitive deionization, etc. More applications are evolving as the scientific and engineering community becomes familiar with the unusual and exceptional physical properties of aerogels, there are also scientific and technical application, as well. This paper discusses a variety of applications under development at Lawrence Livermore National Laboratory for which several types of aerogels are formed in custom sizes and shapes. Particular discussions will focus on the uses of aerogels for physics experiments which rely on the exceptional, sometimes unique, properties of aerogels

  17. Applications of Photocatalytic Disinfection

    Directory of Open Access Journals (Sweden)

    Joanne Gamage

    2010-01-01

    Full Text Available Due to the superior ability of photocatalysis to inactivate a wide range of harmful microorganisms, it is being examined as a viable alternative to traditional disinfection methods such as chlorination, which can produce harmful byproducts. Photocatalysis is a versatile and effective process that can be adapted for use in many applications for disinfection in both air and water matrices. Additionally, photocatalytic surfaces are being developed and tested for use in the context of “self-disinfecting” materials. Studies on the photocatalytic technique for disinfection demonstrate this process to have potential for widespread applications in indoor air and environmental health, biological, and medical applications, laboratory and hospital applications, pharmaceutical and food industry, plant protection applications, wastewater and effluents treatment, and drinking water disinfection. Studies on photocatalytic disinfection using a variety of techniques and test organisms are reviewed, with an emphasis on the end-use application of developed technologies and methods.

  18. Industrial Application of Accelerators

    CERN Multimedia

    CERN. Geneva

    2017-01-01

    At CERN, we are very familiar with large, high energy particle accelerators. However, in the world outside CERN, there are more than 35000 accelerators which are used for applications ranging from treating cancer, through making better electronics to removing harmful micro-organisms from food and water. These are responsible for around $0.5T of commerce each year. Almost all are less than 20 MeV and most use accelerator types that are somewhat different from what is at CERN. These lectures will describe some of the most common applications, some of the newer applications in development and the accelerator technology used for them. It will also show examples of where technology developed for particle physics is now being studied for these applications. Rob Edgecock is a Professor of Accelerator Science, with a particular interest in the medical applications of accelerators. He works jointly for the STFC Rutherford Appleton Laboratory and the International Institute for Accelerator Applications at the Univer...

  19. Industrial Application of Accelerators

    CERN Multimedia

    CERN. Geneva

    2017-01-01

    At CERN, we are very familiar with large, high energy particle accelerators. However, in the world outside CERN, there are more than 35000 accelerators which are used for applications ranging from treating cancer, through making better electronics to removing harmful micro-organisms from food and water. These are responsible for around $0.5T of commerce each year. Almost all are less than 20 MeV and most use accelerator types that are somewhat different from what is at CERN. These lectures will describe some of the most common applications, some of the newer applications in development and the accelerator technology used for them. It will also show examples of where technology developed for particle physics is now being studied for these applications. Rob Edgecock is a Professor of Accelerator Science, with a particular interest in the medical applications of accelerators. He works jointly for the STFC Rutherford Appleton Laboratory and the International Institute for Accelerator Applications at the Uni...

  20. Technical applications of aerogels

    Energy Technology Data Exchange (ETDEWEB)

    Hrubesh, L.W.

    1997-08-18

    Aerogel materials posses such a wide variety of exceptional properties that a striking number of applications have developed for them. Many of the commercial applications of aerogels such as catalysts, thermal insulation, windows, and particle detectors are still under development and new application as have been publicized since the ISA4 Conference in 1994: e.g.; supercapacitors, insulation for heat storage in automobiles, electrodes for capacitive deionization, etc. More applications are evolving as the scientific and engineering community becomes familiar with the unusual and exceptional physical properties of aerogels, there are also scientific and technical application, as well. This paper discusses a variety of applications under development at Lawrence Livermore National Laboratory for which several types of aerogels are formed in custom sizes and shapes. Particular discussions will focus on the uses of aerogels for physics experiments which rely on the exceptional, sometimes unique, properties of aerogels.

  1. Assignment Tracking Android Application

    OpenAIRE

    Akanni, Feranmi Timothy

    2016-01-01

    One of the common ways of checking that knowledge is impacted into students at every level of education is by giving various tasks to students and part of the responsibilities of the teacher is to give assignments to students and check the solution provided by the students. Increase in technology development involves a number of mobile applications that are being developed and released on a daily basis, out of which Android operating application is one of the dominant mobile application. T...

  2. REST based mobile applications

    Science.gov (United States)

    Rambow, Mark; Preuss, Thomas; Berdux, Jörg; Conrad, Marc

    2008-02-01

    Simplicity is the major advantage of REST based webservices. Whereas SOAP is widespread in complex, security sensitive business-to-business aplications, REST is widely used for mashups and end-user centric applicatons. In that context we give an overview of REST and compare it to SOAP. Furthermore we apply the GeoDrawing application as an example for REST based mobile applications and emphasize on pros and cons for the use of REST in mobile application scenarios.

  3. Microcomputer interfacing and applications

    CERN Document Server

    Mustafa, M A

    1990-01-01

    This is the applications guide to interfacing microcomputers. It offers practical non-mathematical solutions to interfacing problems in many applications including data acquisition and control. Emphasis is given to the definition of the objectives of the interface, then comparing possible solutions and producing the best interface for every situation. Dr Mustafa A Mustafa is a senior designer of control equipment and has written many technical articles and papers on the subject of computers and their application to control engineering.

  4. Applications of combinatorial optimization

    CERN Document Server

    Paschos, Vangelis Th

    2013-01-01

    Combinatorial optimization is a multidisciplinary scientific area, lying in the interface of three major scientific domains: mathematics, theoretical computer science and management. The three volumes of the Combinatorial Optimization series aims to cover a wide range of topics in this area. These topics also deal with fundamental notions and approaches as with several classical applications of combinatorial optimization. "Applications of Combinatorial Optimization" is presenting a certain number among the most common and well-known applications of Combinatorial Optimization.

  5. Refrigeration systems and applications

    CERN Document Server

    Dincer, Ibrahim

    2010-01-01

    Refrigeration Systems and Applications, 2nd edition offers a comprehensive treatise that addresses real-life technical and operational problems, enabling the reader to gain an understanding of the fundamental principles and the practical applications of refrigeration technology. New and unique analysis techniques (including exergy as a potential tool), models, correlations, procedures and applications are covered, and recent developments in the field are included - many of which are taken from the author's own research activities in this area. The book also includes so

  6. Application Layer Multicast

    Science.gov (United States)

    Allani, Mouna; Garbinato, Benoît; Pedone, Fernando

    An increasing number of Peer-to-Peer (P2P) Internet applications rely today on data dissemination as their cornerstone, e.g., audio or video streaming, multi-party games. These applications typically depend on some support for multicast communication, where peers interested in a given data stream can join a corresponding multicast group. As a consequence, the efficiency, scalability, and reliability guarantees of these applications are tightly coupled with that of the underlying multicast mechanism.

  7. Microprocessors principles and applications

    CERN Document Server

    Debenham, Michael J

    1979-01-01

    Microprocessors: Principles and Applications deals with the principles and applications of microprocessors and covers topics ranging from computer architecture and programmed machines to microprocessor programming, support systems and software, and system design. A number of microprocessor applications are considered, including data processing, process control, and telephone switching. This book is comprised of 10 chapters and begins with a historical overview of computers and computing, followed by a discussion on computer architecture and programmed machines, paying particular attention to t

  8. Support vector machines applications

    CERN Document Server

    Guo, Guodong

    2014-01-01

    Support vector machines (SVM) have both a solid mathematical background and good performance in practical applications. This book focuses on the recent advances and applications of the SVM in different areas, such as image processing, medical practice, computer vision, pattern recognition, machine learning, applied statistics, business intelligence, and artificial intelligence. The aim of this book is to create a comprehensive source on support vector machine applications, especially some recent advances.

  9. Legacy application integration architecture

    OpenAIRE

    Grom, Jure

    2009-01-01

    Information needs of modern businesses are constantly growing. Own development of a business information system is time consuming and expensive but, as an alternative, using smaller partial solutions doesn’t cover all user needs. Decision to buy a universal solution, often results in only part of it being actively and efficiently used. By application integration we manage to achieve efficient use of applications, since by linking them, we enable sharing of business logics among applications a...

  10. Silver segregation in Ag/a-C nanocomposite coatings for potential application as antibacterial surfaces

    Science.gov (United States)

    Manninen, Noora Kristiina Alves de Sousa

    O desenvolvimento de superficies antibacterianas representa um desafio atual em diferentes aplicacoes industriais, nomeadamente, dispositivos medicos, embalagens alimentares, texteis e sistemas de tratamento de agua. A maioria das bacterias existe em biofilmes que aderem fortemente a diferentes tipos de superficies uma vez que esta adesao representa um mecanismo estrategico de sobrevivencia. O fenomeno da adesao e colonizacao microbiana resulta na falha de diferentes dispositivos e componentes utilizados nas aplicacoes acima mencionadas, tendo como consequencia perdas economicas elevadas e representando tambem um problema de saude publica quando se tratam de aplicacoes como dispositivos medicos ou embalagens alimentares. Neste sentido, ao longo das ultimas decadas o desenvolvimento de superficies antibacterianas tem sido considerada uma estrategia emergente no desenvolvimento de materiais mais eficientes a serem aplicados em diferentes sectores. O objetivo da presente tese consiste no desenvolvimento e caracterizacao de revestimentos nanocompositos multifuncionais baseados em revestimentos de carbono amorfo dopado com nanoparticulas de prata (Ag/a-C) para potencial aplicacao em superficies antibacterianas. A Ag e atualmente considerada como o agente bactericida mais promissor e eficiente, sendo que as nanoparticulas de prata representam o material mais comercializado na area da nanotecnologia. A estrategia de modificacao superficial com revestimentos baseados em carbono amorfo (a-C) tem-se tornado popular do ponto de vista industrial essencialmente, devido entre outras propriedades, a sua resistencia ao desgaste tribologico excecional, que permite combinar uma elevada dureza com um baixo coeficiente de atrito, elevada estabilidade quimica, resistencia a corrosao e biocompatibilidade em diferentes aplicacoes biomedicas. Na atualidade os revestimentos de a-C sao utilizados em diferentes aplicacoes industriais nomeadamente dispositivos medicos, laminas de barbear e

  11. AFRL POSS Applications Research

    National Research Council Canada - National Science Library

    Phillips, Shawn

    2002-01-01

    .... New applications are being investigated (e.g. batteries, capacitors, radomes). The technology transfer to Hybrid Plastics is a success story with significant volume increase and price reduction...

  12. Electrical applications 2

    CERN Document Server

    Tyler, David W

    1998-01-01

    Electrical Applications 2 covers the BTEC NII level objectives in Electrical Applications U86/330. To understand the applications, a knowledge of the underlying principles is needed and these are covered briefly in the text. Key topics discussed are: the transmission and distribution of electrical energy; safety and regulations; tariffs and power factor correction; materials and their applications in the electrical industry; transformers; DC machines; illumination; and fuse protection. Included in each chapter are worked examples which should be carefully worked through before progressing to t

  13. Nanotechnology in Aerospace Applications

    National Research Council Canada - National Science Library

    Meyyappan, M

    2007-01-01

    The aerospace applications for nanotechnology include high strength, low weight composites, improved electronics and displays with low power consumption, variety of physical sensors, multifunctional...

  14. Mongoose for application development

    CERN Document Server

    Holmes, Simon

    2013-01-01

    This book is a mini tutorial full of code examples and strategies to give you plenty of options when building your own applications with MongoDB.This book is ideal for people who want to develop applications on the Node.js stack quickly and efficiently. Prior knowledge of the stack is not essential as the book briefly covers the installation of the core components and builds all aspects of the example application. The focus of the book is on what Mongoose adds to you applications, so experienced Node.js developers will also benefit.

  15. Nanomaterials for Defense Applications

    Science.gov (United States)

    Turaga, Uday; Singh, Vinitkumar; Lalagiri, Muralidhar; Kiekens, Paul; Ramkumar, Seshadri S.

    Nanotechnology has found a number of applications in electronics and healthcare. Within the textile field, applications of nanotechnology have been limited to filters, protective liners for chemical and biological clothing and nanocoatings. This chapter presents an overview of the applications of nanomaterials such as nanofibers and nanoparticles that are of use to military and industrial sectors. An effort has been made to categorize nanofibers based on the method of production. This chapter particularly focuses on a few latest developments that have taken place with regard to the application of nanomaterials such as metal oxides in the defense arena.

  16. Application Technology Research Unit

    Data.gov (United States)

    Federal Laboratory Consortium — To conduct fundamental and developmental research on new and improved application technologies to protect floricultural, nursery, landscape, turf, horticultural, and...

  17. Hardening Azure applications

    CERN Document Server

    Gaurav, Suraj

    2015-01-01

    Learn what it takes to build large scale, mission critical applications -hardened applications- on the Azure cloud platform. This 208 page book covers the techniques and engineering principles that every architect and developer needs to know to harden their Azure/.NET applications to ensure maximum reliability and high availability when deployed at scale. While the techniques are implemented in .NET and optimized for Azure, the principles here will also be valuable for users of other cloud-based development platforms. Applications come in a variety of forms, from simple apps that can be bui

  18. Nanomaterials in biomedical applications

    DEFF Research Database (Denmark)

    Christiansen, Jesper de Claville; Potarniche, Catalina-Gabriela; Vuluga, Z.

    2011-01-01

    Advances in nano materials have lead to applications in many areas from automotive to electronics and medicine. Nano composites are a popular group of nano materials. Nanocomposites in medical applications provide novel solutions to common problems. Materials for implants, biosensors and drug del...

  19. Nanomaterials in biomedical applications

    DEFF Research Database (Denmark)

    Christiansen, Jesper de Claville; Potarniche, Catalina-Gabriela; Vuluga, Z.

    2011-01-01

    Advances in nano materials have lead to applications in many areas from automotive to electronics and medicine. Nano composites are a popular group of nano materials. Nanocomposites in medical applications provide novel solutions to common problems. Materials for implants, biosensors and drug...

  20. Neoglycoconjugates: preparation and applications

    National Research Council Canada - National Science Library

    Lee, Reiko T; Lee, Y. C

    1994-01-01

    ... and ApplicationsNeoglycoconjugates: Preparation and Applications Edited by Y. C. LEE Biology The Johns Baltimore, D e p a r t m e n t Hopkins University M a r y l a n d REIKO T. LEE Biology D e...

  1. Application Security Automation

    Science.gov (United States)

    Malaika, Majid A.

    2011-01-01

    With today's high demand for online applications and services running on the Internet, software has become a vital component in our lives. With every revolutionary technology comes challenges unique to its characteristics; for online applications, security is one huge concern and challenge. Currently, there are several schemes that address…

  2. Advertising on mobile applications

    OpenAIRE

    Sobolevsky, Alexandr

    2015-01-01

    The article analyzes the new method of mobile advertising. Advertising in mobile applications - a subspecies of mobile marketing, where advertising is distributed using mobile phones and smartphones. Ad placement is going on inside of applications and games for smartphones. It has a high potential due to the large number of mobile phone users (over 6.5 billion in 2013).

  3. Computer algebra applications

    International Nuclear Information System (INIS)

    Calmet, J.

    1982-01-01

    A survey of applications based either on fundamental algorithms in computer algebra or on the use of a computer algebra system is presented. Recent work in biology, chemistry, physics, mathematics and computer science is discussed. In particular, applications in high energy physics (quantum electrodynamics), celestial mechanics and general relativity are reviewed. (Auth.)

  4. Progressive Web applications

    CERN Multimedia

    CERN. Geneva

    2017-01-01

    Progressive Web Applications are native-like applications running inside of a browser context. In my presentation I would like describe their characteristics, benchmarks and building process using a quick and simple case study example with focus on Service Workers api.

  5. Connected vehicle application : safety.

    Science.gov (United States)

    2015-01-01

    Connected vehicle safety applications are designed to increase situational awareness : and reduce or eliminate crashes through vehicle-to-infrastructure (V2I), vehicle-to-vehicle (V2V), and vehicle-to-pedestrian (V2P) data transmissions. Applications...

  6. Dilemmas in SEA application

    DEFF Research Database (Denmark)

    Lyhne, Ivar

    Dilemmas in SEA Application: The DK Energy SectorIvar Lyhne - lyhne@plan.aau.dk. Based on three years of collaborative research, this paper outlines dilemmas in the application of SEA in the strategic development of the Danish energy sector. The dilemmas are based on concrete examples from practice...

  7. Applications of Evolutionary Computation

    NARCIS (Netherlands)

    Mora, Antonio M.; Squillero, Giovanni; Di Chio, C; Agapitos, Alexandros; Cagnoni, Stefano; Cotta, Carlos; Fernández De Vega, F; Di Caro, G A; Drechsler, R.; Ekárt, A; Esparcia-Alcázar, Anna I.; Farooq, M; Langdon, W B; Merelo-Guervós, J.J.; Preuss, M; Richter, O.-M.H.; Silva, Sara; Sim$\\$~oes, A; Squillero, Giovanni; Tarantino, Ernesto; Tettamanzi, Andrea G B; Togelius, J; Urquhart, Neil; Uyar, A S; Yannakakis, G N; Smith, Stephen L; Caserta, Marco; Ramirez, Adriana; Voß, Stefan; Squillero, Giovanni; Burelli, Paolo; Mora, Antonio M.; Squillero, Giovanni; Jan, Mathieu; Matthias, M; Di Chio, C; Agapitos, Alexandros; Cagnoni, Stefano; Cotta, Carlos; Fernández De Vega, F; Di Caro, G A; Drechsler, R.; Ekárt, A; Esparcia-Alcázar, Anna I.; Farooq, M; Langdon, W B; Merelo-Guervós, J.J.; Preuss, M; Richter, O.-M.H.; Silva, Sara; Sim$\\$~oes, A; Squillero, Giovanni; Tarantino, Ernesto; Tettamanzi, Andrea G B; Togelius, J; Urquhart, Neil; Uyar, A S; Yannakakis, G N; Caserta, Marco; Ramirez, Adriana; Voß, Stefan; Squillero, Giovanni; Burelli, Paolo; Esparcia-Alcazar, Anna I; Silva, Sara; Agapitos, Alexandros; Cotta, Carlos; De Falco, Ivanoe; Cioppa, Antonio Della; Diwold, Konrad; Ekart, Aniko; Tarantino, Ernesto; Vega, Francisco Fernandez De; Burelli, Paolo; Sim, Kevin; Cagnoni, Stefano; Simoes, Anabela; Merelo, J.J.; Urquhart, Neil; Haasdijk, Evert; Zhang, Mengjie; Squillero, Giovanni; Eiben, A E; Tettamanzi, Andrea G B; Glette, Kyrre; Rohlfshagen, Philipp; Schaefer, Robert; Caserta, Marco; Ramirez, Adriana; Voß, Stefan

    2015-01-01

    The application of genetic and evolutionary computation to problems in medicine has increased rapidly over the past five years, but there are specific issues and challenges that distinguish it from other real-world applications. Obtaining reliable and coherent patient data, establishing the clinical

  8. Geometry and its applications

    CERN Document Server

    Meyer, Walter J

    2006-01-01

    Meyer''s Geometry and Its Applications, Second Edition, combines traditional geometry with current ideas to present a modern approach that is grounded in real-world applications. It balances the deductive approach with discovery learning, and introduces axiomatic, Euclidean geometry, non-Euclidean geometry, and transformational geometry. The text integrates applications and examples throughout and includes historical notes in many chapters. The Second Edition of Geometry and Its Applications is a significant text for any college or university that focuses on geometry''s usefulness in other disciplines. It is especially appropriate for engineering and science majors, as well as future mathematics teachers.* Realistic applications integrated throughout the text, including (but not limited to): - Symmetries of artistic patterns- Physics- Robotics- Computer vision- Computer graphics- Stability of architectural structures- Molecular biology- Medicine- Pattern recognition* Historical notes included in many chapters...

  9. Lasers Fundamentals and Applications

    CERN Document Server

    Thyagarajan, K

    2010-01-01

    Lasers: Fundamentals and Applications, serves as a vital textbook to accompany undergraduate and graduate courses on lasers and their applications. Ever since their invention in 1960, lasers have assumed tremendous importance in the fields of science, engineering and technology because of their diverse uses in basic research and countless technological applications. This book provides a coherent presentation of the basic physics behind the way lasers work, and presents some of their most important applications in vivid detail. After reading this book, students will understand how to apply the concepts found within to practical, tangible situations. This textbook includes worked-out examples and exercises to enhance understanding, and the preface shows lecturers how to most beneficially match the textbook with their course curricula. The book includes several recent Nobel Lectures, which will further expose students to the emerging applications and excitement of working with lasers. Students who study lasers, ...

  10. Applications of ionizing radiations

    International Nuclear Information System (INIS)

    2014-01-01

    Developments in standard applications and brand new nuclear technologies, with high impact on the future of the agriculture, medicine, industry and the environmental preservation. The Radiation Technology Center (CTR) mission is to apply the radiation and radioisotope technologies in Industry, Health, Agriculture, and Environmental Protection, expanding the scientific knowledge, improving human power resources, transferring technology, generating products and offering services for the Brazilian society. The CTR main R and D activities are in consonance with the IPEN Director Plan (2011-2013) and the Applications of Ionizing Radiation Program, with four subprograms: Irradiation of Food and Agricultural Products; Radiation and Radioisotopes Applications in Industry and Environment; Radioactive Sources and Radiation Applications in Human Health; and Radioactive Facilities and Equipment for the Applications of Nuclear Techniques

  11. GPU computing and applications

    CERN Document Server

    See, Simon

    2015-01-01

    This book presents a collection of state of the art research on GPU Computing and Application. The major part of this book is selected from the work presented at the 2013 Symposium on GPU Computing and Applications held in Nanyang Technological University, Singapore (Oct 9, 2013). Three major domains of GPU application are covered in the book including (1) Engineering design and simulation; (2) Biomedical Sciences; and (3) Interactive & Digital Media. The book also addresses the fundamental issues in GPU computing with a focus on big data processing. Researchers and developers in GPU Computing and Applications will benefit from this book. Training professionals and educators can also benefit from this book to learn the possible application of GPU technology in various areas.

  12. Mobile Learning Applications Audit

    Directory of Open Access Journals (Sweden)

    Paul POCATILU

    2010-01-01

    Full Text Available While mobile learning (m-learning applications have proven their value in educational activities, there is a need to measure their reliability, accessibility and further more their trustworthiness. Mobile devices are far more vulnerable then classic computers and present inconvenient interfaces due to their size, hardware limitations and their mobile connectivity. Mobile learning applications should be audited to determine if they should be trusted or not, while multimedia contents like automatic speech recognition (ASR can improve their accessibility. This article will start with a brief introduction on m-learning applications, then it will present the audit process for m-learning applications, it will iterate their specific security threats, it will define the ASR process, and it will elaborate how ASR can enhance accessibility of these types of applications.

  13. Database Application Schema Forensics

    Directory of Open Access Journals (Sweden)

    Hector Quintus Beyers

    2014-12-01

    Full Text Available The application schema layer of a Database Management System (DBMS can be modified to deliver results that may warrant a forensic investigation. Table structures can be corrupted by changing the metadata of a database or operators of the database can be altered to deliver incorrect results when used in queries. This paper will discuss categories of possibilities that exist to alter the application schema with some practical examples. Two forensic environments are introduced where a forensic investigation can take place in. Arguments are provided why these environments are important. Methods are presented how these environments can be achieved for the application schema layer of a DBMS. A process is proposed on how forensic evidence should be extracted from the application schema layer of a DBMS. The application schema forensic evidence identification process can be applied to a wide range of forensic settings.

  14. Building Social Web Applications

    CERN Document Server

    Bell, Gavin

    2009-01-01

    Building a web application that attracts and retains regular visitors is tricky enough, but creating a social application that encourages visitors to interact with one another requires careful planning. This book provides practical solutions to the tough questions you'll face when building an effective community site -- one that makes visitors feel like they've found a new home on the Web. If your company is ready to take part in the social web, this book will help you get started. Whether you're creating a new site from scratch or reworking an existing site, Building Social Web Applications

  15. Wind energy applications guide

    Energy Technology Data Exchange (ETDEWEB)

    anon.

    2001-01-01

    The brochure is an introduction to various wind power applications for locations with underdeveloped transmission systems, from remote water pumping to village electrification. It includes an introductory section on wind energy, including wind power basics and system components and then provides examples of applications, including water pumping, stand-alone systems for home and business, systems for community centers, schools, and health clinics, and examples in the industrial area. There is also a page of contacts, plus two specific example applications for a wind-diesel system for a remote station in Antarctica and one on wind-diesel village electrification in Russia.

  16. Handbook of satellite applications

    CERN Document Server

    Madry, Scott; Camacho-Lara, Sergio

    2017-01-01

    The first edition of this ground breaking reference work was the most comprehensive reference source available about the key aspects of the satellite applications field. This updated second edition covers the technology, the markets, applications and regulations related to satellite telecommunications, broadcasting and networking—including civilian and military systems; precise satellite navigation and timing networks (i.e. GPS and others); remote sensing and meteorological satellite systems. Created under the auspices of the International Space University based in France, this brand new edition is now expanded to cover new innovative small satellite constellations, new commercial launching systems, innovation in military application satellites and their acquisition, updated appendices, a useful glossary and more.

  17. Developing Large Web Applications

    CERN Document Server

    Loudon, Kyle

    2010-01-01

    How do you create a mission-critical site that provides exceptional performance while remaining flexible, adaptable, and reliable 24/7? Written by the manager of a UI group at Yahoo!, Developing Large Web Applications offers practical steps for building rock-solid applications that remain effective even as you add features, functions, and users. You'll learn how to develop large web applications with the extreme precision required for other types of software. Avoid common coding and maintenance headaches as small websites add more pages, more code, and more programmersGet comprehensive soluti

  18. Professional Tizen application development

    CERN Document Server

    Jaygarl, HoJun; Kim, YoonSoo; Choi, Eunyoung; Bradwick, Kevin; Lansdell

    2014-01-01

    Create powerful, marketable applications with Tizen for the smartphone and beyond  Tizen is the only platform designed for multiple device categories that is HTML5-centric and entirely open source. Written by experts in the field, this comprehensive guide includes chapters on both web and native application development, covering subjects such as location and social features, advanced UIs, animations, sensors and multimedia. This book is a comprehensive resource for learning how to develop Tizen web and native applications that are polished, bug-free and ready to sell on a range of smart dev

  19. Biomaterials and therapeutic applications

    Science.gov (United States)

    Ferraro, Angelo

    2016-03-01

    A number of organic and inorganic, synthetic or natural derived materials have been classified as not harmful for the human body and are appropriate for medical applications. These materials are usually named biomaterials since they are suitable for introduction into living human tissues of prosthesis, as well as for drug delivery, diagnosis, therapies, tissue regeneration and many other clinical applications. Recently, nanomaterials and bioabsorbable polymers have greatly enlarged the fields of application of biomaterials attracting much more the attention of the biomedical community. In this review paper I am going to discuss the most recent advances in the use of magnetic nanoparticles and biodegradable materials as new biomedical tools.

  20. Superconductivity and its application

    International Nuclear Information System (INIS)

    Spadoni, M.

    1988-01-01

    This paper, after a short introduction to superconductivity and to multifilamentary superconducting composites is aiming to review the state of the art and the future perspective of some of the applications of the superconducting materials. The main interest is focussed to large scale applications like, for istance, magnets for accelerators or fusion reactors, superconducting system for NMR thomography, etc. A short paragraph is dedicated to applications for high sensitivity instrumentation. The paper is then concluded by some considerations about the potentialities of the newly discovered high critical temperature materials

  1. Android Applications Security

    Directory of Open Access Journals (Sweden)

    Paul POCATILU

    2011-01-01

    Full Text Available The use of smartphones worldwide is growing very fast and also the malicious attacks have increased. The mobile security applications development keeps the pace with this trend. The paper presents the vulnerabilities of mobile applications. The Android applications and devices are analyzed through the security perspective. The usage of restricted API is also presented. The paper also focuses on how users can prevent these malicious attacks and propose some prevention measures, including the architecture of a mobile security system for Android devices.

  2. The application of RFQs

    International Nuclear Information System (INIS)

    Schempp, A.

    1992-01-01

    The Radio Frequency Quadrupole Accelerator (RFQ) has found wide application, not only as the preinjector linac for new high energy light ion accelerators but also in a variety of other projects. Progress in development has made ion linacs practical for medical and industrial applications including radiation therapy, isotope and neutron production, material modification and ion beam diagnostic. The paper discusses various projects together with applications in science where RFQs serve as stand-alone tools, for example for the calibration of detectors, as decelerators or as small compact beam sources for atomic physics and materials research. (Author) 7 figs., 40 refs

  3. Professional mobile application development

    CERN Document Server

    McWherter, Jeff

    2012-01-01

    Create applications for all major smartphone platforms Creating applications for the myriad versions and varieties of mobile phone platforms on the market can be daunting to even the most seasoned developer. This authoritative guide is written in such as way that it takes your existing skills and experience and uses that background as a solid foundation for developing applications that cross over between platforms, thereby freeing you from having to learn a new platform from scratch each time. Concise explanations walk you through the tools and patterns for developing for all the mobile platfo

  4. Professional Cocoa Application Security

    CERN Document Server

    Lee, Graham J

    2010-01-01

    The first comprehensive security resource for Mac and iPhone developers. The Mac platform is legendary for security, but consequently, Apple developers have little appropriate security information available to help them assure that their applications are equally secure. This Wrox guide provides the first comprehensive go-to resource for Apple developers on the available frameworks and features that support secure application development.: While Macs are noted for security, developers still need to design applications for the Mac and the iPhone with security in mind; this guide offers the first

  5. Biomedical applications of polymers

    CERN Document Server

    Gebelein, C G

    1991-01-01

    The biomedical applications of polymers span an extremely wide spectrum of uses, including artificial organs, skin and soft tissue replacements, orthopaedic applications, dental applications, and controlled release of medications. No single, short review can possibly cover all these items in detail, and dozens of books andhundreds of reviews exist on biomedical polymers. Only a few relatively recent examples will be cited here;additional reviews are listed under most of the major topics in this book. We will consider each of the majorclassifications of biomedical polymers to some extent, inclu

  6. Excimer laser applications

    International Nuclear Information System (INIS)

    Fantoni, R.

    1988-01-01

    This lecture deals with laser induced material photoprocessing, especially concerning those processes which are initiated by u.v. lasers (mostly excimer laser). Advantages of using the u.v. radiation emitted by excimer lasers, both in photophysical and photochemical processes of different materials, are discussed in detail. Applications concerning microelectronics are stressed with respect to other applications in different fields (organic chemistry, medicine). As further applications of excimer lasers, main spectroscopic techniques for ''on line'' diagnostics which employ excimer pumped dye lasers, emitting tunable radiation in the visible and near u.v. are reviewed

  7. Express web application development

    CERN Document Server

    Yaapa, Hage

    2013-01-01

    Express Web Application Development is a practical introduction to learning about Express. Each chapter introduces you to a different area of Express, using screenshots and examples to get you up and running as quickly as possible.If you are looking to use Express to build your next web application, ""Express Web Application Development"" will help you get started and take you right through to Express' advanced features. You will need to have an intermediate knowledge of JavaScript to get the most out of this book.

  8. Lift application development cookbook

    CERN Document Server

    Garcia, Gilberto T

    2013-01-01

    Lift Application Development Cookbook contains practical recipes on everything you will need to create secure web applications using this amazing framework.The book first teaches you basic topics such as starting a new application and gradually moves on to teach you advanced topics to achieve a certain task. Then, it explains every step in detail so that you can build your knowledge about how things work.This book is for developers who have at least some basic knowledge about Scala and who are looking for a functional, secure, and modern web framework. Prior experience with HTML and JavaScript

  9. User Types in Online Applications

    Directory of Open Access Journals (Sweden)

    Ion IVAN

    2011-08-01

    Full Text Available Online applications are presented in the context of information society. Online applications characteristics are analyzed. Quality characteristics are presented in relation to online applications users. Types of users for AVIO application are presented. Use cases for AVIO application are identified. The limitations of AVIO application are defined. Types of users in online applications are identified. The threedimensional matrix of access to the online application resources is built. The user type-oriented database is structured. Access management of the fields related to the database tables is analyzed. The classification of online applications users is done.

  10. Thermodynamics foundations and applications

    CERN Document Server

    Gyftopoulos, Elias P

    2005-01-01

    Designed by two MIT professors, this authoritative text discusses basic concepts and applications in detail, emphasizing generality, definitions, and logical consistency. More than 300 solved problems cover realistic energy systems and processes.

  11. Capital Projects Application (CPA)

    Data.gov (United States)

    General Services Administration — Capital Projects application (CPA) provides users with the ability to maintain project related financial data for Budget Activity (BA) 51, 55, 64, 01, 02, 03, 04....

  12. Food Applications and Regulation

    Science.gov (United States)

    Gálvez, Antonio; Abriouel, Hikmate; Omar, Nabil Ben; Lucas, Rosario

    This chapter deals with food applications of bacteriocins. Regulatory issues on the different possibilities for incorporating bacteriocins as bioprotectants are discussed. Specific applications of bacteriocins or bacteriocin-producing strains are described for main food categories, including milk and dairy products, raw meats, ready-to-eat meat and poultry products, fermented meats, fish and fish products or fermented fish. The last section of the chapter deals with applications in foods and beverages derived from plant materials, such as raw vegetable foods, fruits and fruit juices, cooked food products, fermented vegetable foods and ­fermented beverages. Results obtained for application of bacteriocins in combination with other hurdles are also discussed for each specific case, with a special emphasis on novel food packaging and food-processing technologies, such as irradiation, pulsed electric field treatments or high hydrostatic pressure treatment.

  13. Nuclear Technology applications

    International Nuclear Information System (INIS)

    Cibils Machado, W. E- mail: wrcibils@adinet.com.uy

    2002-01-01

    The present work tries on the applications of the nuclear technology in the life daily, such as agriculture and feeding, human health, industry, non destructive essays, isotopic hydrology, and the nuclear power stations for electricity production and radioisotopes production

  14. Industrial applications of radiochemistry

    International Nuclear Information System (INIS)

    Kobayashi, Masatoshi

    1979-01-01

    The industrial application of radiochemistry is summarized, mainly in regard to the application of tracers and activation analysis. Changes in the utilization of radioisotopes in Japan are quoted according to the statistics of the Japan Information Center of Science and Technology (JICST) and reports of the Japan Isotope Conference since 1956. In order to clarify the application of industrial tracers, especially physical tracers in the manufacturing process, serial changes in the concentration of radioactive tracers retained in a bath and in Hg in a soda factory were determined. A radiorelease method used for analysis of exhaust fumes from automobiles is introduced and purification of Al by means by activation analysis, which is used to analyze extremely small amounts of impurities in highly pure materials, is described. Also, application of 252 Cf for activation analysis and its legal intricacies are discussed. (Namekawa, K.)

  15. Condom application - slideshow

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/presentations/100109.htm Condom application - series—Procedure, part 1 To use the ... Go to slide 3 out of 3 Overview Condoms are made of latex rubber, polyurethane or lamb ...

  16. Special functions & their applications

    CERN Document Server

    Lebedev, N N

    1972-01-01

    Famous Russian work discusses the application of cylinder functions and spherical harmonics; gamma function; probability integral and related functions; Airy functions; hyper-geometric functions; more. Translated by Richard Silverman.

  17. Thermoluminescence and their applications

    International Nuclear Information System (INIS)

    Rodrigues, G.V.

    1986-01-01

    The theory involved in the phenomenon of thermoluminescence emission, the characteristics of the main thermoluminescent phosphorus and some of their applications are presented. Some of the main thermoluminescent dosemeters used in dosimetry are described. (M.C.K.) [pt

  18. Designing Adaptive Web Applications

    DEFF Research Database (Denmark)

    Dolog, Peter

    2008-01-01

    Learning system to study a discipline. In business to business interaction, different requirements and parameters of exchanged business requests might be served by different services from third parties. Such applications require certain intelligence and a slightly different approach to design. Adpative web......The unique characteristic of web applications is that they are supposed to be used by much bigger and diverse set of users and stakeholders. An example application area is e-Learning or business to business interaction. In eLearning environment, various users with different background use the e......-based applications aim to leave some of their features at the design stage in the form of variables which are dependent on several criteria. The resolution of the variables is called adaptation and can be seen from two perspectives: adaptation by humans to the changed requirements of stakeholders and dynamic system...

  19. Applications of decelerated ions

    International Nuclear Information System (INIS)

    Johnson, B.M.

    1985-03-01

    Many facilities whose sole purpose had been to accelerate ion beams are now becoming decelerators as well. The development and current status of accel-decel operations is reviewed here. Applications of decelerated ions in atomic physics experiments are discussed

  20. Microtron for radiation applications

    International Nuclear Information System (INIS)

    Soni, H.C.; Ramamurthi, S.S.

    1993-01-01

    The electron accelerator called microtron is a powerful tool for research, medical and industrial applications which need electron beam in energy range of few tens of MeV. Either electron beam from microtron is directly used for radiation applications or electron beam is utilized to produce x-rays or neutrons which are eventually used for radiation applications. After considering the vast potential, lower cost, simpler construction and excellent quality of electron beam from microtron, it was decided to develop this machine at Centre for Advanced Technology (CAT). The microtrons in two standard models have been developed which will cover all the above mentioned applications except free electron lasers. The microtron of model 1 provides electron beam of 20 MeV, 15/30 mA and that of model 2 provides electron beam of 8/12 MeV, 50/30 mA. (author). 2 figs., 1 tab

  1. Applications of Clustering

    Indian Academy of Sciences (India)

    First page Back Continue Last page Overview Graphics. Applications of Clustering. Biology – medical imaging, bioinformatics, ecology, phylogenies problems etc. Market research. Data Mining. Social Networks. Any problem measuring similarity/correlation. (dimensions represent different parameters)

  2. Neutron sources and applications

    Energy Technology Data Exchange (ETDEWEB)

    Price, D.L. [ed.] [Argonne National Lab., IL (United States); Rush, J.J. [ed.] [National Inst. of Standards and Technology, Gaithersburg, MD (United States)

    1994-01-01

    Review of Neutron Sources and Applications was held at Oak Brook, Illinois, during September 8--10, 1992. This review involved some 70 national and international experts in different areas of neutron research, sources, and applications. Separate working groups were asked to (1) review the current status of advanced research reactors and spallation sources; and (2) provide an update on scientific, technological, and medical applications, including neutron scattering research in a number of disciplines, isotope production, materials irradiation, and other important uses of neutron sources such as materials analysis and fundamental neutron physics. This report summarizes the findings and conclusions of the different working groups involved in the review, and contains some of the best current expertise on neutron sources and applications.

  3. Neutron sources and applications

    International Nuclear Information System (INIS)

    Price, D.L.; Rush, J.J.

    1994-01-01

    Review of Neutron Sources and Applications was held at Oak Brook, Illinois, during September 8--10, 1992. This review involved some 70 national and international experts in different areas of neutron research, sources, and applications. Separate working groups were asked to (1) review the current status of advanced research reactors and spallation sources; and (2) provide an update on scientific, technological, and medical applications, including neutron scattering research in a number of disciplines, isotope production, materials irradiation, and other important uses of neutron sources such as materials analysis and fundamental neutron physics. This report summarizes the findings and conclusions of the different working groups involved in the review, and contains some of the best current expertise on neutron sources and applications

  4. Thermoluminescence and applications

    International Nuclear Information System (INIS)

    Rodrigues, G.V.

    1986-01-01

    The theory of thermoluminescent emission, the characteristics of main thermoluminescent phosphorus, and some applications are presented. The main thermoluminescent dosemeters used in dosimetry are related. (M.C.K.)

  5. Engineering Adaptive Web Applications

    DEFF Research Database (Denmark)

    Dolog, Peter

    2007-01-01

    Information and services on the web are accessible for everyone. Users of the web differ in their background, culture, political and social environment, interests and so on. Ambient intelligence was envisioned as a concept for systems which are able to adapt to user actions and needs....... With the growing amount of information and services, the web applications become natural candidates to adopt the concepts of ambient intelligence. Such applications can deal with divers user intentions and actions based on the user profile and can suggest the combination of information content and services which...... suit the user profile the most. This paper summarizes the domain engineering framework for such adaptive web applications. The framework provides guidelines to develop adaptive web applications as members of a family. It suggests how to utilize the design artifacts as knowledge which can be used...

  6. Wordpress web application development

    CERN Document Server

    Ratnayake, Rakhitha Nimesh

    2015-01-01

    This book is intended for WordPress developers and designers who want to develop quality web applications within a limited time frame and for maximum profit. Prior knowledge of basic web development and design is assumed.

  7. Pedal Application Errors

    Science.gov (United States)

    2012-03-01

    This project examined the prevalence of pedal application errors and the driver, vehicle, roadway and/or environmental characteristics associated with pedal misapplication crashes based on a literature review, analysis of news media reports, a panel ...

  8. BIOSENSORS FOR ENVIRONMENTAL APPLICATIONS

    Science.gov (United States)

    A review, with 19 references, is given on challenges and possible opportunities for the development of biosensors for environmental monitoring applications. The high cost and slow turnaround times typically associated with the measurement of regulated pollutants clearly indicates...

  9. 76 FR 60836 - Applicants

    Science.gov (United States)

    2011-09-30

    .... Safeway Global Shipping LLC (NVO), 9630 Clarewood Street, Building D6, Houston, TX 77054, Officers...), Margaret J. Zimmer, President, Application Type: Add NVO Service. ] Zur-Go, Inc (NVO & OFF), 6907 NW., 82nd...

  10. Evolution of Mobile Applications

    Directory of Open Access Journals (Sweden)

    Phongtraychack Anachack

    2018-01-01

    Full Text Available Currently, we can see the rapid evolution of mobile technology, which involves mobile communication, mobile hardware, and mobile software. Features of mobile phones largely depend on software. In contemporary information and communication age [1–4], mobile application is one of the most concerned and rapidly developing areas. At the same time, the development of mobile application undergoes great changes with the introduction of new software, service platforms and software development kits (SDK. These changes lead to appearance of many new service platforms such as Google with Android and Apple with iOS. This article presents the information about the evolution of mobile application, gives some statistical data on the past and present situation, demonstrates how individual users of mobile devices can benefit, and shows how mobile applications affect society from the ethical perspective.

  11. Photovoltaic systems and applications

    Energy Technology Data Exchange (ETDEWEB)

    1982-01-01

    Abstracts are given of presentations given at a project review meeting held at Albuquerque, NM. The proceedings cover the past accomplishments and current activities of the Photovoltaic Systems Research, Balance-of-System Technology Development and System Application Experiments Projects at Sandia National Laboratories. The status of intermediate system application experiments and residential system analysis is emphasized. Some discussion of the future of the Photovoltaic Program in general, and the Sandia projects in particular is also presented.

  12. Applications for alliform carbon

    Energy Technology Data Exchange (ETDEWEB)

    Gogotsi, Yury; Mochalin, Vadym; McDonough, IV, John Kenneth; Simon, Patrice; Taberna, Pierre Louis

    2017-02-21

    This invention relates to novel applications for alliform carbon, useful in conductors and energy storage devices, including electrical double layer capacitor devices and articles incorporating such conductors and devices. Said alliform carbon particles are in the range of 2 to about 20 percent by weight, relative to the weight of the entire electrode. Said novel applications include supercapacitors and associated electrode devices, batteries, bandages and wound healing, and thin-film devices, including display devices.

  13. Industrial Robot Label Applicator

    OpenAIRE

    Kukasch, Kai

    2017-01-01

    The thesis deals with a project carried out for developing and setting up a robot label applicator system. The requirement was that RFID tracking labels can be applied on flexible positions, without manual effort and rearrangement, via programming. The purpose of the robot label applicator system is to increase the efficiency in production sites, where the RFID label position can change, depending on product or other reasons. New label positions should be programmed easily with a human-m...

  14. Superconductivity and their applications

    OpenAIRE

    Roque, António

    2017-01-01

    Trabalho apresentado em International Conference on Renewable Energies and Power Quality (ICREPQ’17), 4 a 6 de Abril de 2017, Málaga, Espanha The research in the field of superconductivity has led to the synthesis of superconducting materials with features that allow you to expand the applicability of this kind of materials. Among the superconducting materials characteristics, the critical temperature of the superconductor is framing the range and type of industrial applications that can b...

  15. Formal groups and applications

    CERN Document Server

    Hazewinkel, Michiel

    2012-01-01

    This book is a comprehensive treatment of the theory of formal groups and its numerous applications in several areas of mathematics. The seven chapters of the book present basics and main results of the theory, as well as very important applications in algebraic topology, number theory, and algebraic geometry. Each chapter ends with several pages of historical and bibliographic summary. One prerequisite for reading the book is an introductory graduate algebra course, including certain familiarity with category theory.

  16. Magnesium motorcycle applications

    International Nuclear Information System (INIS)

    Jianyong Cao; Zonghe Zhang; Dongxia Xiang; Jun Wang

    2005-01-01

    Magnesium, the lightest engineering structural metal, has been comprehensively used in castings of aviation and aerospace, communication and transportation, and IT components. This paper introduced the history, advantages and difficulties of magnesium castings for motorcycle application as well as its application state in China. It also indicated the production situation of magnesium motorcycle components in CQMST and difficulties need to overcome for further development. (orig.)

  17. Superconductor electronic device applications

    International Nuclear Information System (INIS)

    VanDuzer, T.

    1989-01-01

    Superconductors are becoming important in many applications where high sensitivity or speed is required. In this paper the authors give brief introduction to superconductive device physics and some comments on the role of high-temperature superconductors. They then present the basic principles of a number of applications in metrology, electromagnetic sensing, and analog and digital circuits. They conclude with the prospects for hybrid semiconductor-superconductor devices, circuits, and systems

  18. Applications of Genetic Programming

    DEFF Research Database (Denmark)

    Gaunholt, Hans; Toma, Laura

    1996-01-01

    In this report a study of genetic programming (GP) has been performed with respect to a number of applications such as Symbolic function regression, Solving Symbolic Differential Equations, Image encoding, the ant problem etc.......In this report a study of genetic programming (GP) has been performed with respect to a number of applications such as Symbolic function regression, Solving Symbolic Differential Equations, Image encoding, the ant problem etc....

  19. Applications of Nuclear Physics

    OpenAIRE

    Hayes, Anna C.

    2017-01-01

    Today the applications of nuclear physics span a very broad range of topics and fields. This review discusses a number of aspects of these applications, including selected topics and concepts in nuclear reactor physics, nuclear fusion, nuclear non-proliferation, nuclear-geophysics, and nuclear medicine. The review begins with a historic summary of the early years in applied nuclear physics, with an emphasis on the huge developments that took place around the time of World War II, and that und...

  20. Modelling Foundations and Applications

    DEFF Research Database (Denmark)

    This book constitutes the refereed proceedings of the 8th European Conference on Modelling Foundations and Applications, held in Kgs. Lyngby, Denmark, in July 2012. The 20 revised full foundations track papers and 10 revised full applications track papers presented were carefully reviewed......, as well as the high quality of the results presented in these accepted papers, demonstrate the maturity and vibrancy of the field....

  1. Technology Applications Team: Applications of aerospace technology

    Science.gov (United States)

    1993-01-01

    Highlights of the Research Triangle Institute (RTI) Applications Team activities over the past quarter are presented in Section 1.0. The Team's progress in fulfilling the requirements of the contract is summarized in Section 2.0. In addition to our market-driven approach to applications project development, RTI has placed increased effort on activities to commercialize technologies developed at NASA Centers. These Technology Commercialization efforts are summarized in Section 3.0. New problem statements prepared by the Team in the reporting period are presented in Section 4.0. The Team's transfer activities for ongoing projects with the NASA Centers are presented in Section 5.0. Section 6.0 summarizes the status of four add-on tasks. Travel for the reporting period is described in Section 7.0. The RTI Team staff and consultants and their project responsibilities are listed in Appendix A. The authors gratefully acknowledge the contributions of many individuals to the RTI Technology Applications Team program. The time and effort contributed by managers, engineers, and scientists throughout NASA were essential to program success. Most important to the program has been a productive working relationship with the NASA Field Center Technology Utilization (TU) Offices. The RTI Team continues to strive for improved effectiveness as a resource to these offices. Industry managers, technical staff, medical researchers, and clinicians have been cooperative and open in their participation. The RTI Team looks forward to continuing expansion of its interaction with U.S. industry to facilitate the transfer of aerospace technology to the private sector.

  2. Radioisotopes production and applications

    International Nuclear Information System (INIS)

    Dash, Ashutosh

    2015-01-01

    Application of radioisotopes for both medical and industrial applications constitutes one of the most important peaceful uses of atomic energy. The striking diffusion and the exciting perspective of radioisotope for a plethora of medical and industrial applications are mainly attributable to the penetrating and ionization properties of radiation emanating from radioisotopes. The revolutionary medical applications of radioisotopes for the diagnosis and treatment of a multitude of diseases are causing a rapid expansion of the nuclear medicine field. While the industrial uses of radioisotopes are not expanding as quickly, also require large amounts of radioisotopes. Production of radioisotopes is not only the first step, but also the most crucial for the success as well as sustainable growth of radioisotope applications. With the rapid growth and expanding areas of applications, the demands for isotopes have increased several folds. A number of radioisotopes of different physical half-life, energy of the particle or gamma emission, specific activity and chemistry are now regularly produced both at commercial centers as well as at selected nuclear science research institutes utilizing reactors and cyclotrons to meet the ever growing need

  3. LCS Content Document Application

    Science.gov (United States)

    Hochstadt, Jake

    2011-01-01

    My project at KSC during my spring 2011 internship was to develop a Ruby on Rails application to manage Content Documents..A Content Document is a collection of documents and information that describes what software is installed on a Launch Control System Computer. It's important for us to make sure the tools we use everyday are secure, up-to-date, and properly licensed. Previously, keeping track of the information was done by Excel and Word files between different personnel. The goal of the new application is to be able to manage and access the Content Documents through a single database backed web application. Our LCS team will benefit greatly with this app. Admin's will be able to login securely to keep track and update the software installed on each computer in a timely manner. We also included exportability such as attaching additional documents that can be downloaded from the web application. The finished application will ease the process of managing Content Documents while streamlining the procedure. Ruby on Rails is a very powerful programming language and I am grateful to have the opportunity to build this application.

  4. Production and characterization of ceramic composite Al{sub 2}O{sub 3}-TiO{sub 2} reinforced with Y{sub 2}O{sub 3} and its stability in crude oil for internal coating of petroleum tankers; Producao e caracterizacao de compositos ceramicos Al{sub 2}O{sub 3}-TiO{sub 2} reforcado com Y{sub 2}O{sub 3} e sua estabilidade em petroleo cru para revestimento interno de navios petroleiros

    Energy Technology Data Exchange (ETDEWEB)

    Yadava, Y.P.; David, N.R.; Sanguinetti Ferreira, R.A.; Shinohara, A.H., E-mail: yadava@ufpe.br, E-mail: natielle.ramos@hotmail.com [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil). Departamento de Engenharia Mecanica

    2014-07-01

    The internal surfaces of crude petroleum tankers are subjected to corrosive environments, therefore it is of great importance to research coatings for the protection of those structures. Ceramic materials generally exhibit characteristic chemical inertness and are shown as material option for this application. In this study alumina-titania ceramic composites have been produced and reinforced with yttria. These composites were produced by thermo-mechanical process, sintered at 1350 ° C for 24 hours, and left to cool down in the oven. The structural and microstructural characterization of the sintered material was tested by X-ray diffraction and scanning electron microscopy. And its mechanical property was studied by Vickers microhardness test. After this characterization, the samples underwent a stability test where they were immersed in crude oil at room temperature for 60 days, during which were periodically subjected to tests related to stability, which was found found that the material was free from cracks, fissures or fractures, presenting for these reasons characteristics of inertia when subjected to crude oil environment. (author)

  5. Nonlinear Optics and Applications

    Science.gov (United States)

    Abdeldayem, Hossin A. (Editor); Frazier, Donald O. (Editor)

    2007-01-01

    Nonlinear optics is the result of laser beam interaction with materials and started with the advent of lasers in the early 1960s. The field is growing daily and plays a major role in emerging photonic technology. Nonlinear optics play a major role in many of the optical applications such as optical signal processing, optical computers, ultrafast switches, ultra-short pulsed lasers, sensors, laser amplifiers, and many others. This special review volume on Nonlinear Optics and Applications is intended for those who want to be aware of the most recent technology. This book presents a survey of the recent advances of nonlinear optical applications. Emphasis will be on novel devices and materials, switching technology, optical computing, and important experimental results. Recent developments in topics which are of historical interest to researchers, and in the same time of potential use in the fields of all-optical communication and computing technologies, are also included. Additionally, a few new related topics which might provoke discussion are presented. The book includes chapters on nonlinear optics and applications; the nonlinear Schrodinger and associated equations that model spatio-temporal propagation; the supercontinuum light source; wideband ultrashort pulse fiber laser sources; lattice fabrication as well as their linear and nonlinear light guiding properties; the second-order EO effect (Pockels), the third-order (Kerr) and thermo-optical effects in optical waveguides and their applications in optical communication; and, the effect of magnetic field and its role in nonlinear optics, among other chapters.

  6. Applications of Cell Microencapsulation.

    Science.gov (United States)

    Opara, Emmanuel C

    2017-01-01

    The goal of this chapter is to provide an overview of the different purposes for which the cell microencapsulation technology can be used. These include immunoisolation of non-autologous cells used for cell therapy; immobilization of cells for localized (targeted) delivery of therapeutic products to ablate, repair, or regenerate tissue; simultaneous delivery of multiple therapeutic agents in cell therapy; spatial compartmentalization of cells in complex tissue engineering; expansion of cells in culture; and production of different probiotics and metabolites for industrial applications. For each of these applications, specific examples are provided to illustrate how the microencapsulation technology can be utilized to achieve the purpose. However, successful use of the cell microencapsulation technology for whatever purpose will ultimately depend upon careful consideration for the choice of the encapsulating polymers, the method of fabrication (cross-linking) of the microbeads, which affects the permselectivity, the biocompatibility and the mechanical strength of the microbeads as well as environmental parameters such as temperature, humidity, osmotic pressure, and storage solutions.The various applications discussed in this chapter are illustrated in the different chapters of this book and where appropriate relevant images of the microencapsulation products are provided. It is hoped that this outline of the different applications of cell microencapsulation would provide a good platform for tissue engineers, scientists, and clinicians to design novel tissue constructs and products for therapeutic and industrial applications.

  7. Discrete mathematics with applications

    CERN Document Server

    Koshy, Thomas

    2003-01-01

    This approachable text studies discrete objects and the relationsips that bind them. It helps students understand and apply the power of discrete math to digital computer systems and other modern applications. It provides excellent preparation for courses in linear algebra, number theory, and modern/abstract algebra and for computer science courses in data structures, algorithms, programming languages, compilers, databases, and computation.* Covers all recommended topics in a self-contained, comprehensive, and understandable format for students and new professionals * Emphasizes problem-solving techniques, pattern recognition, conjecturing, induction, applications of varying nature, proof techniques, algorithm development and correctness, and numeric computations* Weaves numerous applications into the text* Helps students learn by doing with a wealth of examples and exercises: - 560 examples worked out in detail - More than 3,700 exercises - More than 150 computer assignments - More than 600 writing projects*...

  8. Optimized packings with applications

    CERN Document Server

    Pintér, János

    2015-01-01

    This volume presents a selection of case studies that address a substantial range of optimized object packings (OOP) and their applications. The contributing authors are well-recognized researchers and practitioners. The mathematical modelling and numerical solution aspects of each application case study are presented in sufficient detail. A broad range of OOP problems are discussed: these include various specific and non-standard container loading and object packing problems, as well as the stowing of hazardous and other materials on container ships, data centre resource management, automotive engineering design, space station logistic support, cutting and packing problems with placement constraints, the optimal design of LED street lighting, robust sensor deployment strategies, spatial scheduling problems, and graph coloring models and metaheuristics for packing applications. Novel points of view related to model development and to computational nonlinear, global, mixed integer optimization and heuristic st...

  9. Radioisotope applications in industry

    International Nuclear Information System (INIS)

    Frevert, E.

    1983-03-01

    The practical applications of the isotope technique are reported and illustrated by examples of works of the Department of Isotope Application of the Austrian Research Centre Seibersdorf. First the field of process controlling device and controll is described, including thickness, density and moisture gauging, the estimation of coatings and material compounds, the location of material defects and the level control. After this a detailed description of all kinds of tracer investigations is given like measurements of flow rate, intermixture, distribution and volume, investigations of corrosion, wear and lubrication and locations of all kind. A short description of gas ionisation, sources of light and isotope batteries is mentioned. Finally a general view of the applications in the fields of chemistry, biology, agriculture and medicine and the most important of the Austrian law of protective screen and its enactment are given. (Author) [de

  10. Applications of photovoltaics

    International Nuclear Information System (INIS)

    Pearsall, N.

    1999-01-01

    The author points out that although photovoltaics can be used for generating electricity for the same applications as many other means of generation, they really come into their own where disadvantages associated with an intermittent unpredictable supply are not severe. The paper discusses the advantages and disadvantages to be taken into account when considering a photovoltaic power system. Five main applications, based on the system features, are listed and explained. They are: consumer, professional, rural electrification, building-integrated, centralised grid connected and space power. A brief history of the applications of photovoltaics is presented with statistical data on the growth of installed capacity since 1992. The developing market for photovoltaics is discussed together with how environmental issues have become a driver for development of building-integrated photovoltaics

  11. Applications of interval computations

    CERN Document Server

    Kreinovich, Vladik

    1996-01-01

    Primary Audience for the Book • Specialists in numerical computations who are interested in algorithms with automatic result verification. • Engineers, scientists, and practitioners who desire results with automatic verification and who would therefore benefit from the experience of suc­ cessful applications. • Students in applied mathematics and computer science who want to learn these methods. Goal Of the Book This book contains surveys of applications of interval computations, i. e. , appli­ cations of numerical methods with automatic result verification, that were pre­ sented at an international workshop on the subject in EI Paso, Texas, February 23-25, 1995. The purpose of this book is to disseminate detailed and surveyed information about existing and potential applications of this new growing field. Brief Description of the Papers At the most fundamental level, interval arithmetic operations work with sets: The result of a single arithmetic operation is the set of all possible results as the o...

  12. Applications of stable isotopes

    International Nuclear Information System (INIS)

    Gregg, C.T.

    1977-01-01

    Clinical applications include the galactose breath test which consists of oral administration of 13 C-labeled galactose and measurement of the 13 C content of respired CO 2 as a function of time in patients with cirrhotic livers for diagnosis of liver dysfunction. Another application was the breath test to study glucose metabolism in children. Respired 13 CO 2 from ingested glucose- 13 C was measured for normal and diabetic children. Studies on mice in which 60 percent of the body carbon was replaced with 13 C failed to show significant effects of the isotope. Studies on biochemical applications include nuclear magnetic resonance studies of 13 C-labeled amino acids from Chlorella pyrenoidosa; studies on 15 N nmr spectra of arginine-guanidino- 13 C-2,3-- 15 N 2 as a function of pH; and isolation of fatty acids from algae

  13. Practical applications of phosphors

    CERN Document Server

    Yen, William M; Yamamoto, Hajime

    2006-01-01

    Drawn from the second edition of the best-selling Phosphor Handbook, Practical Applications of Phosphors outlines methods for the production of various phosphors and discusses a broad spectrum of applications. Beginning with methods for synthesis and related technologies, the book sets the stage by classifying and then explaining practical phosphors according to usage. It describes the operating principle and structure of phosphor devices and the phosphor characteristics required for a given device, then covers the manufacturing processes and characteristics of phosphors. The book discusses research and development currently under way on phosphors with potential for practical usage and touches briefly on phosphors that have played a historical role, but are no longer of practical use. It provides a comprehensive treatment of applications including lamps and cathode-ray tubes, x-ray and ionizing radiation, and for vacuum fluorescent and field emission displays and covers inorganic and organic electroluminescen...

  14. Engineering Web Applications

    DEFF Research Database (Denmark)

    Casteleyn, Sven; Daniel, Florian; Dolog, Peter

    Nowadays, Web applications are almost omnipresent. The Web has become a platform not only for information delivery, but also for eCommerce systems, social networks, mobile services, and distributed learning environments. Engineering Web applications involves many intrinsic challenges due...... design and implementation to deployment and maintenance. They stress the importance of models in Web application development, and they compare well-known Web-specific development processes like WebML, WSDM and OOHDM to traditional software development approaches like the waterfall model and the spiral...... model. Important problem areas inherent to the Web, like localization, personalization, accessibility, and usage analysis, are dealt with in detail, and a final chapter provides both a description of and an outlook on recent Semantic Web and Web 2.0 developments. Overall, their book delivers...

  15. Lie algebras and applications

    CERN Document Server

    Iachello, Francesco

    2015-01-01

    This course-based primer provides an introduction to Lie algebras and some of their applications to the spectroscopy of molecules, atoms, nuclei and hadrons. In the first part, it concisely presents the basic concepts of Lie algebras, their representations and their invariants. The second part includes a description of how Lie algebras are used in practice in the treatment of bosonic and fermionic systems. Physical applications considered include rotations and vibrations of molecules (vibron model), collective modes in nuclei (interacting boson model), the atomic shell model, the nuclear shell model, and the quark model of hadrons. One of the key concepts in the application of Lie algebraic methods in physics, that of spectrum generating algebras and their associated dynamic symmetries, is also discussed. The book highlights a number of examples that help to illustrate the abstract algebraic definitions and includes a summary of many formulas of practical interest, such as the eigenvalues of Casimir operators...

  16. Novel materials based on chitosan, its derivatives and cellulose fibres

    Science.gov (United States)

    Fernandes, Susana Cristina de Matos

    O presente trabalho tem como principal objectivo o desenvolvimento de novos materiais baseados em quitosano, seus derivados e celulose, na forma de nanofibras ou de papel. Em primeiro lugar procedeu-se a purificacao das amostras comerciais de quitosano e a sua caracterizacao exaustiva em termos morfologicos e fisicoquimicos. Devido a valores contraditorios encontrados na literatura relativamente a energia de superficie do quitosano, e tendo em conta a sua utilizacao como precursor de modificacoes quimicas e a sua aplicacao em misturas com outros materiais, realizou-se tambem um estudo sistematico da determinacao da energia de superficie do quitosano, da quitina e seus respectivos homologos monomericos, por medicao de ângulos de contacto Em todas as amostras comerciais destes polimeros identificaram-se impurezas nao polares que estao associadas a erros na determinacao da componente polar da energia de superficie. Apos a remocao destas impurezas, o valor da energia total de superficie (gs), e em particular da sua componente polar, aumentou consideravelmente. Depois de purificadas e caracterizadas, algumas das amostras de quitosano foram entao usadas na preparacao de filmes nanocompositos, nomeadamente dois quitosanos com diferentes graus de polimerizacao, correspondentes derivados soluveis em agua (cloreto de N-(3-(N,N,N-trimetilamonio)-2- hidroxipropilo) de quitosano) e nanofibras de celulose como reforco (celulose nanofibrilada (NFC) e celulose bacteriana (BC). Estes filmes transparentes foram preparados atraves de um processo simples e com conotacao 'verde' pela dispersao homogenea de diferentes teores de NFC (ate 60%) e BC (ate 40%) nas solucoes de quitosano (1.5% w/v) seguida da evaporacao do solvente. Os filmes obtidos foram depois caracterizados por diversas tecnicas, tais como SEM, AFM, difraccao de raio-X, TGA, DMA, ensaios de traccao e espectroscopia no visivel. Estes filmes sao altamente transparentes e apresentam melhores propriedades mecânicas e maior

  17. Clinical applications of magnetoencephalography.

    Science.gov (United States)

    Stufflebeam, Steven M; Tanaka, Naoaki; Ahlfors, Seppo P

    2009-06-01

    Magnetoencephalography (MEG), in which magnetic fields generated by brain activity are recorded outside of the head, is now in routine clinical practice throughout the world. MEG has become a recognized and vital part of the presurgical evaluation of patients with epilepsy and patients with brain tumors. We review investigations that show an improvement in the postsurgical outcomes of patients with epilepsy by localizing epileptic discharges. We also describe the most common clinical MEG applications that affect the management of patients, and discuss some applications that are close to having a clinical impact on patients. (c) 2009 Wiley-Liss, Inc.

  18. Mixtures Estimation and Applications

    CERN Document Server

    Mengersen, Kerrie; Titterington, Mike

    2011-01-01

    This book uses the EM (expectation maximization) algorithm to simultaneously estimate the missing data and unknown parameter(s) associated with a data set. The parameters describe the component distributions of the mixture; the distributions may be continuous or discrete. The editors provide a complete account of the applications, mathematical structure and statistical analysis of finite mixture distributions along with MCMC computational methods, together with a range of detailed discussions covering the applications of the methods and features chapters from the leading experts on the subject

  19. Current military laser applications

    Energy Technology Data Exchange (ETDEWEB)

    Flinchbaugh, D.E.

    1975-08-01

    Several important military applications with the predominant laser type used are reviewed. Most of these lasers are infrared lasers of one sort or another. Airborne tactical programs utilizing laser designator/illuminators are pictorially summarized, including range finding, target seeking, designation, tracking, reconnaissance, and surveillance. A typical designator optical system configuration is presented and discussed. Examples of operational laser systems are given. It is seen that many of the laser applications in the civilian community have either direct or indirect analogs in the military field. A self-contained HF/DF chemical laser weapon that recirculates its by-products is examined.

  20. Laravel application development blueprints

    CERN Document Server

    Kiliçdagi, Arda

    2013-01-01

    Follow along as we work together to build 10 different applications using Laravel 4. Since each chapter is devoted to the design of a different application, there is no need to read the book in any particular order. Instead, you can pick and choose the blueprints that are of most interest to you and dive right in.This book is for intermediate to advanced level PHP programmers who want to master Laravel. It's assumed that you will have some experience with PHP already. This book is also for those who are already using a different PHP framework and are looking for better solutions.

  1. Science Application Teams

    Science.gov (United States)

    2000-01-01

    This paper discusses the science application team activities. Science Application team are: (1) Represent the diversity of NASA onboard computing of the future. (2) Drive architecture and system software requirements. (3) Demonstrate the benefit of highly capable computing onboard. (4) Study the birth of the first galaxies. (5) Study formation of stars. (6) Discusses the next generation space telescope hardware/software requirement: image processing and on-board optical calibration. Also discusses gamma ray large area space telescope; orbital thermal imaging spectrometer; solar terrestrial probe program; autonomous Mars rover;fault tolerance and errors.

  2. Modular Mobile Application Design

    Directory of Open Access Journals (Sweden)

    Jim Hahn

    2012-10-01

    Full Text Available This article describes the development of the Minrva library app for Android phones. The decisions to build a native application with Java and use a modular design are discussed. The application includes five modules: catalog search, in-building navigation, a barcode scanning feature, and up to date notifications of circulating technology availability. A sixth module, Amazon recommendations, that is not included in the version of the app that was released is also discussed. The article also reports on the findings of two rounds of usability testing and the plans for future development of the app.

  3. PSA in application

    International Nuclear Information System (INIS)

    Thadani, A.C.

    1989-01-01

    This paper reports on Probabilistic Safety Assessment methodologies which are finding wide application within the nuclear power industry. Plant specific studies have been useful in identifying design vulnerabilities, providing a basis for prioritization of plant modifications and in an operations management role. PSA applications in regulatory activities have also proven very beneficial to the US NRC in assessing significance of operating plant events/issues, consideration of potential design improvements, standard plant licensing and conducting regulatory and cost-benefit analyses on proposed generic issue resolution. The benefits from such studies are concluded to be well worth their cost

  4. Location Based Application Availability

    Science.gov (United States)

    Naeem Akram, Raja; Markantonakis, Konstantinos; Mayes, Keith

    Smart cards are being integrated into a diverse range of industries: ranging from banking, telecom, transport, home/office access control to health and E-passport. Traditionally, cardholders are required to carry a smart card for each application. However, recent developments in the Near Field Communication (NFC) have renewed the interest in multiple applications for different services on a single device. This paper builds onto the NFC initiative and avoids the smart card ownership issues that hinder the adoption of such devices. The proposal integrates the Global Positioning System with the NFC in mobile phones to provide a ubiquitously and flexible service access model.

  5. Optimization : insights and applications

    CERN Document Server

    Brinkhuis, Jan

    2005-01-01

    This self-contained textbook is an informal introduction to optimization through the use of numerous illustrations and applications. The focus is on analytically solving optimization problems with a finite number of continuous variables. In addition, the authors provide introductions to classical and modern numerical methods of optimization and to dynamic optimization. The book's overarching point is that most problems may be solved by the direct application of the theorems of Fermat, Lagrange, and Weierstrass. The authors show how the intuition for each of the theoretical results can be s

  6. Erokovnik mobile application

    OpenAIRE

    Barlič, Gregor

    2009-01-01

    The object of this dissertation is to describe a mobile application eRokovnik for managing different types of events. The application is primarily intended for modern mobile phones and as such allows to effectively monitor all functions and other events by user. The user has a transparent, simple and efficient user interface for easy management of data. Data is stored in the database on your mobile device locally. A backup copy of saved data can be made on user request using the integrate...

  7. Application of stepping motor

    International Nuclear Information System (INIS)

    1980-10-01

    This book is divided into three parts, which is about practical using of stepping motor. The first part has six chapters. The contents of the first part are about stepping motor, classification of stepping motor, basic theory og stepping motor, characteristic and basic words, types and characteristic of stepping motor in hybrid type and basic control of stepping motor. The second part deals with application of stepping motor with hardware of stepping motor control, stepping motor control by microcomputer and software of stepping motor control. The last part mentions choice of stepping motor system, examples of stepping motor, measurement of stepping motor and practical cases of application of stepping motor.

  8. Cluster analysis for applications

    CERN Document Server

    Anderberg, Michael R

    1973-01-01

    Cluster Analysis for Applications deals with methods and various applications of cluster analysis. Topics covered range from variables and scales to measures of association among variables and among data units. Conceptual problems in cluster analysis are discussed, along with hierarchical and non-hierarchical clustering methods. The necessary elements of data analysis, statistics, cluster analysis, and computer implementation are integrated vertically to cover the complete path from raw data to a finished analysis.Comprised of 10 chapters, this book begins with an introduction to the subject o

  9. Nanoelectronic device applications handbook

    CERN Document Server

    Morris, James E

    2013-01-01

    Nanoelectronic Device Applications Handbook gives a comprehensive snapshot of the state of the art in nanodevices for nanoelectronics applications. Combining breadth and depth, the book includes 68 chapters on topics that range from nano-scaled complementary metal-oxide-semiconductor (CMOS) devices through recent developments in nano capacitors and AlGaAs/GaAs devices. The contributors are world-renowned experts from academia and industry from around the globe. The handbook explores current research into potentially disruptive technologies for a post-CMOS world.These include: Nanoscale advance

  10. Plasmonics theory and applications

    CERN Document Server

    Shahbazyan, Tigran V

    2014-01-01

    This contributed volume summarizes recent theoretical developments in plasmonics and its applications in physics, chemistry, materials science, engineering, and medicine. It focuses on recent advances in several major areas of plasmonics including plasmon-enhanced spectroscopies, light scattering, many-body effects, nonlinear optics, and ultrafast dynamics. The theoretical and computational methods used in these investigations include electromagnetic calculations, density functional theory calculations, and nonequilibrium electron dynamics calculations. The book presents a comprehensive overview of these methods as well as their applications to various current problems of interest.

  11. Tunable laser applications

    CERN Document Server

    Duarte, FJ

    2008-01-01

    Introduction F. J. Duarte Spectroscopic Applications of Tunable Optical Parametric Oscillators B. J. Orr, R. T. White, and Y. He Solid-State Dye Lasers Costela, I. García-Moreno, and R. Sastre Tunable Lasers Based on Dye-Doped Polymer Gain Media Incorporating Homogeneous Distributions of Functional Nanoparticles F. J. Duarte and R. O. James Broadly Tunable External-Cavity Semiconductor Lasers F. J. Duarte Tunable Fiber Lasers T. M. Shay and F. J. Duarte Fiber Laser Overview and Medical Applications

  12. Gas solubilities widespread applications

    CERN Document Server

    Gerrard, William

    1980-01-01

    Gas Solubilities: Widespread Applications discusses several topics concerning the various applications of gas solubilities. The first chapter of the book reviews Henr's law, while the second chapter covers the effect of temperature on gas solubility. The third chapter discusses the various gases used by Horiuti, and the following chapters evaluate the data on sulfur dioxide, chlorine data, and solubility data for hydrogen sulfide. Chapter 7 concerns itself with solubility of radon, thoron, and actinon. Chapter 8 tackles the solubilities of diborane and the gaseous hydrides of groups IV, V, and

  13. Pump characteristics and applications

    CERN Document Server

    Volk, Michael

    2013-01-01

    Providing a wealth of information on pumps and pump systems, Pump Characteristics and Applications, Third Edition details how pump equipment is selected, sized, operated, maintained, and repaired. The book identifies the key components of pumps and pump accessories, introduces the basics of pump and system hydraulics as well as more advanced hydraulic topics, and details various pump types, as well as special materials on seals, motors, variable frequency drives, and other pump-related subjects. It uses example problems throughout the text, reinforcing the practical application of the formulae

  14. Graphs Theory and Applications

    CERN Document Server

    Fournier, Jean-Claude

    2008-01-01

    This book provides a pedagogical and comprehensive introduction to graph theory and its applications. It contains all the standard basic material and develops significant topics and applications, such as: colorings and the timetabling problem, matchings and the optimal assignment problem, and Hamiltonian cycles and the traveling salesman problem, to name but a few. Exercises at various levels are given at the end of each chapter, and a final chapter presents a few general problems with hints for solutions, thus providing the reader with the opportunity to test and refine their knowledge on the

  15. Experimental approaches and applications

    CERN Document Server

    Crasemann, Bernd

    1975-01-01

    Atomic Inner-Shell Processes, Volume II: Experimental Approaches and Applications focuses on the physics of atomic inner shells, with emphasis on experimental aspects including the use of radioactive atoms for studies of atomic transition probabilities. Surveys of modern techniques of electron and photon spectrometry are also presented, and selected practical applications of inner-shell processes are outlined. Comprised of six chapters, this volume begins with an overview of the general principles underlying the experimental techniques that make use of radioactive isotopes for inner-sh

  16. Developing Web Applications

    CERN Document Server

    Moseley, Ralph

    2007-01-01

    Building applications for the Internet is a complex and fast-moving field which utilizes a variety of continually evolving technologies. Whether your perspective is from the client or server side, there are many languages to master - X(HTML), JavaScript, PHP, XML and CSS to name but a few. These languages have to work together cleanly, logically and in harmony with the systems they run on, and be compatible with any browsers with which they interact. Developing Web Applications presents script writing and good programming practice but also allows students to see how the individual technologi

  17. Medical applications of accelerators

    CERN Document Server

    Rossi, Sandro

    1998-01-01

    At Present, about five thousands accelerators are devoted to biomedical applications. They are mainly used in radiotherapy, research and medical radioisotopes production. In this framework oncological hadron-therapy deserves particular attention since it represents a field in rapid evolution thanks to the joint efforts of laboratories with long experiences in particle physics. It is the case of CERN where the design of an optimised synchrotron for medical applications has been pursued. These lectures present these activities with particular attention to the new developments which are scientifically interesting and/or economically promising.

  18. Permit application modifications

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-11-01

    This document contains the Permit Application Modifications for the Y-12 Industrial Landfill V site on the Oak Ridge Reservation. These modifications include the assessment of stability of the proposed Landfill V under static and loading conditions. Analyses performed include the general slope stability, veneer stability of the bottom liner and cover system, and a liquefaction potential assessment of the foundation soils.

  19. Business Applications of WAP.

    Science.gov (United States)

    van Steenderen, Margaret

    2002-01-01

    Explains the development of WAP (wireless application protocol), how it works, and what the major advantages and disadvantages are, especially when applied to the use of information. Topics include standardization; mobile communications; the effect of WAP on business tools, electronic commerce, and information services; consumers; corporate users;…

  20. Clinical Application of Electrocardiography.

    Science.gov (United States)

    Brammell, H. L.; Orr, William

    The scalar electrocardiogram (ECG) is one of the most important and commonly used clinical tools in medicine. A detailed description of the recordings of cardiac electrical activity made by the ECG is presented, and the vast numbers of uses made with the data provided by this diagnostic tool are cited. Clinical applications of the ECG are listed.…

  1. Computer applications in radiology.

    Science.gov (United States)

    Vannier, M W

    1991-04-01

    Computer applications in radiology are evolving rapidly, tied to incremental improvements in hardware, software, and methods. In computer hardware, the emergence of dramatically improved graphic and computational performance for engineering workstations enables their use for visualization. Major changes in networking, storage, and display technology play a major role in influencing applications. The use of three-dimensional digitizers to perform localization of real three-dimensional points in conjunction with images and the rendering of objects using rapid prototyping methods, such as stereolithography, were recently reported. Major software advances have taken place through the availability of applications packages that are operated with menu-driven or point-and-click user interfaces, data flow languages, or complete turnkey applications. Imaging methods including CT, MR imaging, digital radiography, biomagnetism, and optical range sensing, which take advantage of advanced computer technology, are new this year. Image processing for multimodality fusion or image registration, visualization, reconstruction, and quantification of images, have been reported at a wide variety of conferences and in key publications. New computer methods to fabricate custom orthopaedic implants, and to improve imaging technology assessment were introduced.

  2. Knotoids, Braidoids and Applications

    Directory of Open Access Journals (Sweden)

    Neslihan Gügümcü

    2017-12-01

    Full Text Available This paper is an introduction to the theory of braidoids. Braidoids are geometric objects analogous to classical braids, forming a counterpart theory to the theory of knotoids. We introduce these objects and their topological equivalences, and we conclude with a potential application to the study of proteins.

  3. Medical applications of colloids

    CERN Document Server

    Matijevic, Egon

    2008-01-01

    The first book of its type on the medical and biomedical applications of colloids, although there are some related titles on different topicsDiscusses the effects of uniform particles in drug formulations and releaseEvaluates particle transport and deposition in the human body.

  4. Process intensification : Industrial applications

    NARCIS (Netherlands)

    Kiss, Anton A.

    2016-01-01

    The chapter presents process intensification technologies used in industrial applications, for increasing the eco-efficiency of the chemical equipment with the benefit of lower capital costs, substantial energy saving, reduced footprint, and safety by design. The key topics cover compact heat

  5. Applications of QCD

    International Nuclear Information System (INIS)

    Landshoff, P.V.

    1983-01-01

    The author describes the application of quantum chromodynamics to deep inelastic lepton scattering, the Drell-Yan process, e + e - -annihilation, #betta##betta#-physics, large psub(T) processes, and wide angle quark-quark scattering. Furthermore higher order terms are considered. (HSI)

  6. Applications of fluid dynamics

    International Nuclear Information System (INIS)

    Round, G.R.; Garg, V.K.

    1986-01-01

    This book describes flexible and practical approach to learning the basics of fluid dynamics. Each chapter is a self-contained work session and includes a fluid dynamics concept, an explanation of the principles involved, an illustration of their application and references on where more detailed discussions can be found

  7. Zirconia in biomedical applications.

    Science.gov (United States)

    Chen, Yen-Wei; Moussi, Joelle; Drury, Jeanie L; Wataha, John C

    2016-10-01

    The use of zirconia in medicine and dentistry has rapidly expanded over the past decade, driven by its advantageous physical, biological, esthetic, and corrosion properties. Zirconia orthopedic hip replacements have shown superior wear-resistance over other systems; however, risk of catastrophic fracture remains a concern. In dentistry, zirconia has been widely adopted for endosseous implants, implant abutments, and all-ceramic crowns. Because of an increasing demand for esthetically pleasing dental restorations, zirconia-based ceramic restorations have become one of the dominant restorative choices. Areas covered: This review provides an updated overview of the applications of zirconia in medicine and dentistry with a focus on dental applications. The MEDLINE electronic database (via PubMed) was searched, and relevant original and review articles from 2010 to 2016 were included. Expert commentary: Recent data suggest that zirconia performs favorably in both orthopedic and dental applications, but quality long-term clinical data remain scarce. Concerns about the effects of wear, crystalline degradation, crack propagation, and catastrophic fracture are still debated. The future of zirconia in biomedical applications will depend on the generation of these data to resolve concerns.

  8. Biomedical applications engineering tasks

    Science.gov (United States)

    Laenger, C. J., Sr.

    1976-01-01

    The engineering tasks performed in response to needs articulated by clinicians are described. Initial contacts were made with these clinician-technology requestors by the Southwest Research Institute NASA Biomedical Applications Team. The basic purpose of the program was to effectively transfer aerospace technology into functional hardware to solve real biomedical problems.

  9. Star Products and Applications

    OpenAIRE

    Iida, Mari; Yoshioka, Akira

    2010-01-01

    Star products parametrized by complex matrices are defined. Especially commutative associative star products are treated, and star exponentials with respect to these star products are considered. Jacobi's theta functions are given as infinite sums of star exponentials. As application, several concrete identities are obtained by properties of the star exponentials.

  10. Membrane contactor applications

    NARCIS (Netherlands)

    Klaassen, R.; Feron, P.H.M.; Jansen, A.

    2008-01-01

    In a membrane contactor the membrane separation is completely integrated with an extraction or absorption operation in order to exploit the benefits of both technologies fully. Membrane contactor applications that have been developed can be found in both water and gas treatment. Several recently

  11. Technology and applications

    International Nuclear Information System (INIS)

    Bogdany, J.; Vesztergombi, G.

    1994-07-01

    The workshop on Parallel Processing, Technology and Applications, held February 10-11, Budapest, Hungary, covered a variety of topics on computer data processing and parallel computing. One of the 17 presentations discussed the need for massively parallel processing in support of future high energy experiments

  12. Applications Using AIRS Data

    Science.gov (United States)

    Ray, S. E.; Pagano, T. S.; Fetzer, E. J.; Lambrigtsen, B.; Olsen, E. T.; Teixeira, J.; Licata, S. J.; Hall, J. R.; Thompson, C. K.

    2015-12-01

    The Atmospheric Infrared Sounder (AIRS) on NASA's Aqua spacecraft has been returning daily global observations of Earth's atmospheric constituents and properties since 2002. With a 12-year data record and daily, global observations in near real-time, AIRS data can play a role in applications that fall under many of the NASA Applied Sciences focus areas. For vector-borne disease, research is underway using AIRS near surface retrievals to assess outbreak risk, mosquito incubation periods and epidemic potential for dengue fever, malaria, and West Nile virus. For drought applications, AIRS temperature and humidity data are being used in the development of new drought indicators and improvement in the understanding of drought development. For volcanic hazards, new algorithms using AIRS data are in development to improve the reporting of sulfur dioxide concentration, the burden and height of volcanic ash and dust, all of which pose a safety threat to aircraft. In addition, anomaly maps of many of AIRS standard products are being produced to help highlight "hot spots" and illustrate trends. To distribute it's applications imagery, AIRS is leveraging existing NASA data frameworks and organizations to facilitate archiving, distribution and participation in the BEDI. This poster will communicate the status of the applications effort for the AIRS Project and provide examples of new maps designed to best communicate the AIRS data.

  13. Beaming teaching application

    DEFF Research Database (Denmark)

    Markovic, Milos; Madsen, Esben; Olesen, Søren Krarup

    2012-01-01

    BEAMING is a telepresence research project aiming at providing a multimodal interaction between two or more participants located at distant locations. One of the BEAMING applications allows a distant teacher to give a xylophone playing lecture to the students. Therefore, rendering of the xylophon...

  14. Permit application modifications

    International Nuclear Information System (INIS)

    1995-11-01

    This document contains the Permit Application Modifications for the Y-12 Industrial Landfill V site on the Oak Ridge Reservation. These modifications include the assessment of stability of the proposed Landfill V under static and loading conditions. Analyses performed include the general slope stability, veneer stability of the bottom liner and cover system, and a liquefaction potential assessment of the foundation soils

  15. Microfluidics for medical applications

    NARCIS (Netherlands)

    van den Berg, Albert; van den Berg, A.; Segerink, L.I.; Segerink, Loes Irene; Unknown, [Unknown

    2015-01-01

    Lab-on-a-chip devices for point of care diagnostics have been present in clinics for several years now. Alongside their continual development, research is underway to bring the organs and tissue on-a-chip to the patient, amongst other medical applications of microfluidics. This book provides the

  16. Polymeric Microspheres for Medical Applications

    Directory of Open Access Journals (Sweden)

    Ketie Saralidze

    2010-06-01

    Full Text Available Synthetic polymeric microspheres find application in a wide range of medical applications. Among other applications, microspheres are being used as bulking agents, embolic- or drug-delivery particles. The exact composition of the spheres varies with the application and therefore a large array of materials has been used to produce microspheres. In this review, the relation between microsphere synthesis and application is discussed for a number of microspheres that are used for different treatment strategies.

  17. Novel Applications of Peroxidase

    Science.gov (United States)

    Rob, Abdul; Ball, Andrew S.; Tuncer, Munir; Wilson, Michael T.

    1997-02-01

    The article entitled "Novel Biocatalysts Will Work Even Better for Industry" published recently in this Journal (1) was informative and interesting. However it touched only briefly on the application of peroxidase as catalyst. Here, we would like to mention in more detail the novel applications of peroxidase in agricultural, paper pulp, water treatment, pharmaceutical, and medical situations. Firstly, the peroxidase isolated from Phanerochaete chyrosporium has been shown to detoxify herbicides such as atrazine to less toxic compounds and would certainly find potential application in agriculture (2). Secondly, the peroxidase produced by Streptomyces thermoviolaceus may find application in the paper pulp industry as a delignifying agent (3). Thirdly, it has been shown that extracellular peroxidase produced by Streptomyces avermitilis can remove the intense color from paper-mill effluent obtained after semichemical alkaline pulping of wheat straw (4), and thus this enzyme might find application as a catalyst in water treatment plants. Fourthly, the heme-containing horseradish peroxidase enzyme has been exploited in several diagnostic applications in pharmaceutics and medicine, such as the detection of human immunodeficiency virus and cystic fibrosis (5-10). Finally, recent work from our laboratory has suggested that thermophilic nonheme peroxidase produced by Thermomonospora fusca BD25 may find medical use in the diagnosis of myocardial infarction (11, 12). Literature Cited 1. Wiseman, A. J. Chem. Educ. 1996, 73, 55-58. 2. Mougin, C. Appl. Environ. Microbiol. 1994, 60, 705-708. 3. McCarthy A. J.; Peace, W.; Broda, P. Appl. Microbiol. Technol. 1985, 23, 238-244. 4. Hernandez, M; Rodriguez J; Soliveri, J; Copa, J. L; Perez, M. I; Arias, M. E. Appl. Environ. Microbiol. 1994, 60, 3909-3913. 5. Hopfer, S. M.; Aslanzadeh, J. Ann. Clin. Lab. Sci. 1995, 25, 475-480. 6. Suzuki, K; Iman, M. J. Virol. Methods 1995, 55, 347-356. 7. Nielsen, K. J. Immunoassay 1995, 16, 183-197. 8

  18. The fusion applications study - FAME

    International Nuclear Information System (INIS)

    Schultz, K.R.; Engholm, B.A.; Bourque, R.F.; Cheng, E.T.; Schaffer, M.J.; Wong, C.P.C.

    1986-01-01

    The Fusion Applications and Market Evaluation (''FAME'') study, being conducted by GA Technologies for Lawrence Livermore National Laboratory (LLNL) and US Department of Energy, Office of Fusion Energy, (US DOE) is described. This two-year program has a FY86 objective of Evaluating Alternative Applications of Fusion, and a FY87 goal of Exploring Innovative Applications. Applications are being reviewed and categorized into Baseline, Nuclear, Chemical, Electromagnetic, and Thermal application categories. The ''traditional'' applications of electricity generation, fissile fuel and tritium production, and hydrogen production continue to look attractive. Particularly promising new applications to date, with potential for near-term markets, are isotope production and radiation processing, especially when allied with the traditional application of electricity production. The economics of separate applications as well as coproduction are discussed. The combination of electricity and /sup 60/Co production appears to be one of the most attractive

  19. Optical Polarizationin Biomedical Applications

    CERN Document Server

    Tuchin, Valery V; Zimnyakov, Dmitry A

    2006-01-01

    Optical Polarization in Biomedical Applications introduces key developments in optical polarization methods for quantitative studies of tissues, while presenting the theory of polarization transfer in a random medium as a basis for the quantitative description of polarized light interaction with tissues. This theory uses the modified transfer equation for Stokes parameters and predicts the polarization structure of multiple scattered optical fields. The backscattering polarization matrices (Jones matrix and Mueller matrix) important for noninvasive medical diagnostic are introduced. The text also describes a number of diagnostic techniques such as CW polarization imaging and spectroscopy, polarization microscopy and cytometry. As a new tool for medical diagnosis, optical coherent polarization tomography is analyzed. The monograph also covers a range of biomedical applications, among them cataract and glaucoma diagnostics, glucose sensing, and the detection of bacteria.

  20. Thin film device applications

    CERN Document Server

    Kaur, Inderjeet

    1983-01-01

    Two-dimensional materials created ab initio by the process of condensation of atoms, molecules, or ions, called thin films, have unique properties significantly different from the corresponding bulk materials as a result of their physical dimensions, geometry, nonequilibrium microstructure, and metallurgy. Further, these characteristic features of thin films can be drasti­ cally modified and tailored to obtain the desired and required physical characteristics. These features form the basis of development of a host of extraordinary active and passive thin film device applications in the last two decades. On the one extreme, these applications are in the submicron dimensions in such areas as very large scale integration (VLSI), Josephson junction quantum interference devices, magnetic bubbles, and integrated optics. On the other extreme, large-area thin films are being used as selective coatings for solar thermal conversion, solar cells for photovoltaic conver­ sion, and protection and passivating layers. Ind...

  1. Magnetoplasmadynamic thruster applications

    International Nuclear Information System (INIS)

    Pawlik, E.V.

    1976-01-01

    Advance study activities within NASA indicate that electric propulsion will be required to make certain types of potential missions feasible. The large power levels under consideration make magnetoplasmadynamic thrusters a good candidate for these applications since this type of electric thruster is best suited to operation at high power levels. The status of the magnetoplasmadynamic thruster is examined and compared to the ion thruster which also is a candidate. The use of these two types of electric propulsion devices for orbit raising of a self-powered large satellite is examined from a cost standpoint. In addition the use of nuclear electric propulsion is described for use as both a near-earth space tug and for an interplanetary exploration vehicle. These preliminary examinations indicate that the magnetoplasmadynamic thruster is the lowest cost thruster and therefore merits serious consideration for these applications

  2. Diverse applications of radioimmunoassay

    International Nuclear Information System (INIS)

    Yalow, R.S.

    1981-01-01

    The author discussed the issues concerning insulins of the different species (pig, dog and sperm whale) and the applications of species specific antisera in experimental and clinical settings. The possible role of a new form of ACTH as a hormonal marker was also discussed. Three species of insulin (pig, dog, and sperm whale) were separated by human antisera. Immune reaction was utilized to distinguish between endogenous human insulin and exogenously administered animal insulin. The longer acting insulins was found to be more immunogenic than regular crystalline insulins. Insulin concentrations in acid/ethanol extracts of the whole rat brain was about 25 times higher than plasma insulin. Plasma concentration of ACTH could be applicable to effect the distinction between tumor primary in or metastatic to the lung. (Nakanishi, T.)

  3. Nanotechnology applications in osteodistraction

    Directory of Open Access Journals (Sweden)

    Adam E Singleton

    2014-06-01

    Full Text Available Most current strategies for bone regeneration have relatively satisfactory results. However, there are drawbacks and limitations associated with their use and availability, and even controversial reports about their efficacy and cost-effectiveness. The induction of new bone formation through distraction osteogenesis (DO is widespread clinical application in the treatment of bone defects, limb deformities, and fracture nonunions. However, a lengthy period of external fixation is usually needed to allow the new bone to consolidate, and complications such as refracture at the distraction gap often occur. Although various biomaterials have been used as injectable delivery systems in DO models, little has been reported on the use of nanobiomaterials as carrier materials for the sustained release of growth factors in bone regeneration. One area of focus in nanotechnology is the delivery of osteogenic factors in an attempt to modulate the formation of bone. This review article seeks to demonstrate the potential of nanobiomaterials to improve biological applications pertinent to osteodistraction.

  4. Nonlocal diffusion and applications

    CERN Document Server

    Bucur, Claudia

    2016-01-01

    Working in the fractional Laplace framework, this book provides models and theorems related to nonlocal diffusion phenomena. In addition to a simple probabilistic interpretation, some applications to water waves, crystal dislocations, nonlocal phase transitions, nonlocal minimal surfaces and Schrödinger equations are given. Furthermore, an example of an s-harmonic function, its harmonic extension and some insight into a fractional version of a classical conjecture due to De Giorgi are presented. Although the aim is primarily to gather some introductory material concerning applications of the fractional Laplacian, some of the proofs and results are new. The work is entirely self-contained, and readers who wish to pursue related subjects of interest are invited to consult the rich bibliography for guidance.

  5. Quality Control Applications

    CERN Document Server

    Chorafas, Dimitris N

    2013-01-01

    Quality control is a constant priority in electrical, mechanical, aeronautical, and nuclear engineering – as well as in the vast domain of electronics, from home appliances to computers and telecommunications. Quality Control Applications provides guidance and valuable insight into quality control policies; their methods, their implementation, constant observation and associated technical audits. What has previously been a mostly mathematical topic is translated here for engineers concerned with the practical implementation of quality control. Once the fundamentals of quality control are established, Quality Control Applications goes on to develop this knowledge and explain how to apply it in the most effective way. Techniques are described and supported using relevant, real-life, case studies to provide detail and clarity for those without a mathematical background. Among the many practical examples, two case studies dramatize the importance of quality assurance: A shot-by-shot analysis of the errors made ...

  6. Handbook of satellite applications

    CERN Document Server

    Madry, Scott; Camacho-Lara, Sergio

    2013-01-01

    Top space experts from around the world have collaborated to produce this comprehensive, authoritative, and clearly illustrated reference guide to the fast growing, multi-billion dollar field of satellite applications and space communications. This handbook, done under the auspices of the International Space University based in France, addresses not only system technologies but also examines market dynamics, technical standards and regulatory constraints. The handbook is a completely multi-disciplinary reference book that covers, in an in-depth fashion, the fields of satellite telecommunications, Earth observation, remote sensing, satellite navigation, geographical information systems, and geosynchronous meteorological systems. It covers current practices and designs as well as advanced concepts and future systems. It provides a comparative analysis of the common technologies and design elements for satellite application bus structures, thermal controls, power systems, stabilization techniques, telemetry, com...

  7. Information Engineering and Applications

    CERN Document Server

    Ma, Yan; International Conference on Information Engineering and Applications (IEA) 2011

    2012-01-01

    The International Conference on Information Engineering and Applications (IEA) 2011 will be held on October 21-24, 2011, in Chongqing, China. It is organized by Chongqing Normal University, Chongqing University, Shanghai Jiao Tong University, Nanyang Technological University, the University of Michigan, Chongqing University of Arts and Sciences, and sponsored by the National Natural Science Foundation of China. The objective of IEA 2011 is to facilitate an exchange of information on best practices for the latest research advances in the area of information engineering and intelligence applications, which mainly includes computer science and engineering, informatics, communications and control, electrical engineering, information computing, business intelligence and management. IEA 2011 will provide a forum for engineers and scientists in academia, industry, and government to address the most innovative research and development including technical challenges, social and economic issues, and to present and disc...

  8. Application of ecological mapping

    International Nuclear Information System (INIS)

    Sherk, J.A.

    1982-01-01

    The US Fish and Wildlife Service has initiated the production of a comprehensive ecological inventory map series for use as a major new planning tool. Important species data along with special land use designations are displayed on 1:250,000 scale topographic base maps. Sets of maps have been published for the Atlantic and Pacific coastal areas of the United States. Preparation of a map set for the Gulf of Mexico is underway at the present time. Potential application of ecological inventory map series information to a typical land disposal facility could occur during the narrowing of the number of possible disposal sites, the design of potential disposal site studies of ecological resources, the preparation of the environmental report, and the regulatory review of license applications. 3 figures, 3 tables

  9. Biophotonics concepts to applications

    CERN Document Server

    Keiser, Gerd

    2016-01-01

    This book is designed to introduce senior-level and postgraduate students to the principles and applications of biophotonics. It also will serve well as a working reference to practicing physicians, clinicians, biomedical researchers, and biomedical engineers dealing with photonics-based tools and instruments. The book topics include the fundamentals of optics and photonics, the optical properties of biological tissues, various types of light-tissue interactions, microscopy for visualizing tissue components, spectroscopy for optically analyzing the properties of healthy and diseased tissue, and optical biomedical imaging. The tools and techniques described in the book include laser and LED optical sources, photodetectors, optical fibers, bioluminescent probes for labeling cells, optical-based biosensors, nanophotonics, surface plasmon resonance, and lab-on-a-chip technologies. Among the applications are optical coherence tomography (OCT), flow cytometery, photodynamic therapy (PDT), low-level light therapy (L...

  10. Technology applications bulletins

    International Nuclear Information System (INIS)

    Koncinski, W. Jr.

    1989-02-01

    Martin Marietta Energy Systems, Inc. (Energy Systems), operates five facilities for the US Department of Energy (DOE): the Oak Ridge National Laboratory (ORNL), which is a large, multidisciplinary research and development (R and D) center whose primary mission is energy research; the Oak Ridge Y-12 Plant, which engages in defense research, development, and production; and the uranium-enrichment plants at Oak Ridge; Paducah, Kentucky; and Portsmouth, Ohio. Much of the research carried out at these facilities is of interest to industry and to state or local governments. To make information about this research available, the Energy Systems Office of Technology Applications publishes brief descriptions of selected technologies and reports. These technology applications bulletins describe the new technology and inform the reader about how to obtain further information, gain access to technical resources, and initiate direct contact with Energy Systems researchers

  11. Ceramics for fusion applications

    International Nuclear Information System (INIS)

    Clinard, F.W. Jr.

    1987-01-01

    Ceramics are required for a variety of uses in both near-term fusion devices and in commercial powerplants. These materials must retain adequate structural and electrical properties under conditions of neutron, particle and ionizing irradiation; thermal and applied stresses; and physical and chemical sputtering. Ceramics such as Al 2 O 3 , MgAl 2 O 4 , BeO, Si 3 N 4 and SiC are currently under study for fusion applications, and results to date show widely-varying responses to the fusion environment. Materials can be identified today that will meet initial operating requirements, but improvements in physical properties are needed to achieve satisfactory lifetimes for critical applications. (author)

  12. [Industrial application of lipases].

    Science.gov (United States)

    Bancerz, Renata

    2017-01-01

    The ability of lipases to perform specific reactions of transformation (biotransformation) makes these enzymes a useful tool used in many syntheses, for example: in the production of detergents, cosmetics, biosurfactants, in the oil-chemical, paper, dairy, food or pharmaceutical industries. Lipases are ubiquitous enzymes but only lipases produced by microorganisms are important for industrial applications due to their wide variety of properties such as stability in organic solvents, action under mild conditions, high substrate specificity and region- and enantioselectivity, as well as the relatively simple methods of their production in fermentors and recovery from the culture medium. This paper reviews the latest achievements in the production of lipases in the submerged fermentation and solid state fermentation using waste products from the agricultural industry. In addition, new applications of lipases were described, including those for the synthesis of biopolymers and biodiesel and for the production of enantiomeric pharmaceuticals, agrochemicals and flavoring compounds.

  13. Mechanisms, Transmissions and Applications

    CERN Document Server

    Corves, Burkhard

    2012-01-01

    The first Workshop on Mechanisms, Transmissions and Applications -- MeTrApp-2011 was organized by the Mechatronics Department at the Mechanical Engineering Faculty, “Politehnica” University of Timisoara, Romania, under the patronage of the IFToMM Technical Committees Linkages and Mechanical Controls and Micromachines. The workshop brought together researchers and students who work in disciplines associated with mechanisms science and offered a great opportunity for scientists from all over the world to present their achievements, exchange innovative ideas and create solid international links, setting the trend for future developments in this important and creative field. The topics treated in this volume are mechanisms and machine design, mechanical transmissions, mechatronic and biomechanic applications, computational and experimental methods, history of mechanism and machine science and teaching methods.

  14. Quantum mechanics with applications

    CERN Document Server

    Beard, David B

    2014-01-01

    This introductory text emphasizes Feynman's development of path integrals and its application to wave theory for particles. Suitable for undergraduate and graduate students of physics, the well-written, clear, and rigorous text was written by two of the nation's leading authorities on quantum physics. A solid foundation in quantum mechanics and atomic physics is assumed. Early chapters provide background in the mathematical treatment and particular properties of ordinary wave motion that also apply to particle motion. The close relation of quantum theory to physical optics is stressed. Subsequent sections emphasize the physical consequences of a wave theory of material properties, and they offer extensive applications in atomic physics, nuclear physics, solid state physics, and diatomic molecules. Four helpful Appendixes supplement the text.

  15. Magnetism basics and applications

    CERN Document Server

    Stefanita, Carmen-Gabriela

    2012-01-01

    This textbook is aimed at engineering students who are likely to come across magnetics applications in their professional practice. Whether designing lithography equipment containing ferromagnetic brushes, or detecting defects in aeronautics, some basic knowledge of 21st century magnetism is needed. From the magnetic tape on the pocket credit card to the read head in a personal computer, people run into magnetism in many products. Furthermore, in a variety of disciplines tools of the trade exploit magnetic principles, and many interdisciplinary laboratory research areas cross paths with magnetic phenomena that may seem mysterious to the untrained mind. Therefore, this course offers a broad coverage of magnetism topics encountered more often in this millenium, revealing key concepts on which many practical applications rest. Some traditional subjects in magnetism are discussed in the first half of the book, followed by areas likely to spark the curiosity of those more interested in today’s technological achi...

  16. Ceramics for fusion applications

    International Nuclear Information System (INIS)

    Clinard, F.W. Jr.

    1986-01-01

    Ceramics are required for a variety of uses in both near-term fusion devices and in commercial powerplants. These materials must retain adequate structural and electrical properties under conditions of neutron, particle, and ionizing irradiation; thermal and applied stresses; and physical and chemical sputtering. Ceramics such as Al 2 O 3 , MgAl 2 O 4 , BeO, Si 3 N 4 and SiC are currently under study for fusion applications, and results to date show widely-varying response to the fusion environment. Materials can be identified today which will meet initial operating requirements, but improvements in physical properties are needed to achieve satisfactory lifetimes for critical applications

  17. Numerical semigroups and applications

    CERN Document Server

    Assi, Abdallah

    2016-01-01

    This work presents applications of numerical semigroups in Algebraic Geometry, Number Theory, and Coding Theory. Background on numerical semigroups is presented in the first two chapters, which introduce basic notation and fundamental concepts and irreducible numerical semigroups. The focus is in particular on free semigroups, which are irreducible; semigroups associated with planar curves are of this kind. The authors also introduce semigroups associated with irreducible meromorphic series, and show how these are used in order to present the properties of planar curves. Invariants of non-unique factorizations for numerical semigroups are also studied. These invariants are computationally accessible in this setting, and thus this monograph can be used as an introduction to Factorization Theory. Since factorizations and divisibility are strongly connected, the authors show some applications to AG Codes in the final section. The book will be of value for undergraduate students (especially those at a higher leve...

  18. Main applications of superconductors

    International Nuclear Information System (INIS)

    Tixador, P.; Brunet, Y.

    2007-01-01

    In 2004, the world market of superconductivity reached 3.65 billion euros and was mainly concerning the NbTi-type superconductors. The high critical temperature superconductors (HCTS) have not reached the industrial maturity yet, both in terms of efficiency and cost, but this situation may change at medium term. Superconductors are mainly used in the industry today to create moderated to high inductions (1.5 to more than 20 T) inside volumes up to several hundreds of m 3 . This article treats of the present day industrial applications of NbTi and Nb 3 Sn superconductors: 1 - specificities of superconductors: persisting mode, AC losses, protection of a superconducting magnet, dimensioning of a superconducting coil; 2 -industrial magnets: NMR imaging, spectroscopy, proton cyclotron; 3 - magnets for research: high energy physics (accelerators-colliders, detectors), fusion facilities (reaction, magnetic confinement, tokamak, ITER), laboratory magnets; 4 - magnets for specific applications: magnetic separation, magnetic levitated train, MHD. (J.S.)

  19. Nano technology and applications

    International Nuclear Information System (INIS)

    Takriti, S.

    2015-01-01

    Nano technology is the engineering of functional systems at the molecular scale. This covers both works and concepts that are more advanced. In its original sense, nano technology refers to the projected ability to construct items from the bottom up, using techniques and tools being developed today to make complete high performance products. Development of applications incorporating semiconductor nanoparticles to be used in the next generation of products, such as display technology, lighting, solar cells and biological imaging and others are widely progressives. Progress has been made in using medical applications (Nano medicine) which provided the possibility of delivering drugs to specific cells using nanoparticles. Otherwise, nanoparticles have high surface area to volume ratio, allowing many functional groups to be attached to a nanoparticle, which can seek out and bind to certain tumor cells (cancer). (author)

  20. Laravel application development cookbook

    CERN Document Server

    Matula, Terry

    2013-01-01

    Get to grips with a new technology, understand what it is and what it can do for you, and then get to work with the most important features and tasks.A short and precise guide to get you started with EaselJS , helping you to create some cool applications and games.EaselJS greatly simplifies application development in HTML5 Canvas using a syntax and an architecture very similar to the ActionScript 3.0 language. As a result, Flash / Flex developers will immediately feel at home but it's very easy to learn even if you've never opened Flash in your life. The book targets Web designers, animators,

  1. Biomedical applications of nanotechnology.

    Science.gov (United States)

    Ramos, Ana P; Cruz, Marcos A E; Tovani, Camila B; Ciancaglini, Pietro

    2017-04-01

    The ability to investigate substances at the molecular level has boosted the search for materials with outstanding properties for use in medicine. The application of these novel materials has generated the new research field of nanobiotechnology, which plays a central role in disease diagnosis, drug design and delivery, and implants. In this review, we provide an overview of the use of metallic and metal oxide nanoparticles, carbon-nanotubes, liposomes, and nanopatterned flat surfaces for specific biomedical applications. The chemical and physical properties of the surface of these materials allow their use in diagnosis, biosensing and bioimaging devices, drug delivery systems, and bone substitute implants. The toxicology of these particles is also discussed in the light of a new field referred to as nanotoxicology that studies the surface effects emerging from nanostructured materials.

  2. Superconductivity fundamentals and applications

    CERN Document Server

    Buckel, Werner

    2004-01-01

    This is the second English edition of what has become one of the definitive works on superconductivity in German -- currently in its sixth edition. Comprehensive and easy to understand, this introductory text is written especially with the non-specialist in mind. The authors, both long-term experts in this field, present the fundamental considerations without the need for extensive mathematics, describing the various phenomena connected with the superconducting state, with liberal insertion of experimental facts and examples for modern applications. While all fields of superconducting phenomena are dealt with in detail, this new edition pays particular attention to the groundbreaking discovery of magnesium diboride and the current developments in this field. In addition, a new chapter provides an overview of the elements, alloys and compounds where superconductivity has been observed in experiments, together with their major characteristics. The chapter on technical applications has been considerably expanded...

  3. Metagraphs and their applications

    CERN Document Server

    Basu, Amit

    2007-01-01

    The graph is a critical and useful concept in designing many information processing systems. Systems such as transaction processing systems, decision support systems, and workflow systems are all helped immensely by a graphical structure. Simple graphs and digraphs allow for the construction of a variety of system design tools that provide a convenient and appealing format for illustrating information infrastructures, while allowing any subsequent analyses to be performed by the user. However, the metagraph, a new graphical structure that is developed in this book, goes beyond the representational and provides Information Systems with a robust, analytical modeling graphic tool. METAGRAPHS AND THEIR APPLICATIONS is a presentation of metagraph theory and its applications that begins by defining a metagraph and its uses. They are more complex than a simple graph structure, but they allow for representation and analysis of more complex systems. The material contained in this book is presented in two parts. The fi...

  4. Industrial applications at GANIL

    International Nuclear Information System (INIS)

    Delagrange, H.

    1993-01-01

    After a first round of industrial applications using heavy ion beams, GANIL has refocused these activities along the lines defined by a strategy and market study. Heavy ion industrial applications take their roots in the physical effects of the interactions occurring between heavy ion projectiles and matter. Specific equipments operated by GANIL or CIRIL allow users to take benefit from these effects. By heavy ion irradiation, industrial companies qualify radiation hardened electronic components and sensitize plastic films to produce 'nuclear track' membranes. Research and development programs with laboratories of the public sector, focus on heavy ion lithography dedicated to large area luminescent flat screens with field emitter microtips and on tribology with radioactive implanted ions. Even sometimes facing difficulties to fill the gap between industry and research, GANIL is eager to promote heavy ion beam technologies. (author) 36 refs., 6 figs., 5 tabs

  5. Multifractals theory and applications

    CERN Document Server

    Harte, David

    2001-01-01

    Although multifractals are rooted in probability, much of the related literature comes from the physics and mathematics arena. Multifractals: Theory and Applications pulls together ideas from both these areas using a language that makes them accessible and useful to statistical scientists. It provides a framework, in particular, for the evaluation of statistical properties of estimates of the Renyi fractal dimensions.The first section provides introductory material and different definitions of a multifractal measure. The author then examines some of the various constructions for describing multifractal measures. Building from the theory of large deviations, he focuses on constructions based on lattice coverings, covering by point-centered spheres, and cascades processes. The final section presents estimators of Renyi dimensions of integer order two and greater and discusses their properties. It also explores various applications of dimension estimation and provides a detailed case study of spatial point patte...

  6. Iontophoresis: principles and applications

    Directory of Open Access Journals (Sweden)

    Eddy Krueger

    Full Text Available Introduction Iontophoresis is a noninvasive technique used to increase transdermal penetration of substances through the skin layer (epidermis, dermis and hypodermis in a controlled manner. Technological advance in recent decades have provided reduced cost of equipment needed for implementation, which allowed for the expansion of this technique. Objective The aim of this paper is to present the state of the art on iontophoresis, ranging from the atomic characteristics of the ion formation to the current applications of the technique. Methods Were researched papers from databases: IOP publishing, ScienceDirect, Pubmed, Springer, IEEE Xplore, Google Scholar and books with keywords iontophoresis, ions, topical applications between 1967 and 2010. Results Were selected (number of papers and database 1 IOP Publishing, 1 from ScienceDirect, Central, 1 from Springer, 2 from PubMed, 11 from IEEE Xplore, 35 from Google Scholar, and 15 books, totaling 66 references and websites with nationally marketed electrotherapy products. Conclusion Iontophoresis is suitable for applications such as acetic acid (calcific tendinitis and myositis ossificans, calcium chloride and magnesium sulfate (control of musculoskeletal spasms, dexamethasone (inflammation, lidocaine (inflammation of soft tissues, zinc oxide (rheumatoid arthritis. It is also used in cosmetic applications with devices attached to the skin and for eye treatment aimed at specific tissues of the eye, providing a treatment option for various eye diseases, reducing the complications secondary to traditional methods of treatment. The advantages are the significant increase in the release and control of therapeutic agents, including drugs with high molecular weight. The disadvantages of iontophoresis are the complexity of the drug release system and prolonged exposure of the skin to an electrical current.

  7. Homomorphic encryption and applications

    CERN Document Server

    Yi, Xun; Bertino, Elisa

    2014-01-01

    This book introduces the fundamental concepts of homomorphic encryption. From these foundations, applications are developed in the fields of private information retrieval, private searching on streaming data, privacy-preserving data mining, electronic voting and cloud computing. The content is presented in an instructional and practical style, with concrete examples to enhance the reader's understanding. This volume achieves a balance between the theoretical and the practical components of modern information security. Readers will learn key principles of homomorphic encryption as well as their

  8. Advanced Welding Applications

    Science.gov (United States)

    Ding, Robert J.

    2010-01-01

    Some of the applications of advanced welding techniques are shown in this poster presentation. Included are brief explanations of the use on the Ares I and Ares V launch vehicle and on the Space Shuttle Launch vehicle. Also included are microstructural views from four advanced welding techniques: Variable Polarity Plasma Arc (VPPA) weld (fusion), self-reacting friction stir welding (SR-FSW), conventional FSW, and Tube Socket Weld (TSW) on aluminum.

  9. Technology Applications Report

    Science.gov (United States)

    1995-01-01

    most advanced ballistic missile systems. BMDO is upgrading the PATRIOT missile, which is a land -based system designed to intercept aircraft and...a tall cake pan. It can be configured to convert heat from almost any type of fuel, such as liquid or solid biofuel and compressed natural gas...of the reactor have been cited for several applications. For example, some of the unique materials used for the reactor have grabbed the interest of a

  10. Applications of supramolecular chemistry

    CERN Document Server

    Schneider, Hans-Jörg

    2012-01-01

    ""The time is ripe for the present volume, which gathers thorough presentations of the numerous actually realized or potentially accessible applications of supramolecular chemistry by a number of the leading figures in the field. The variety of topics covered is witness to the diversity of the approaches and the areas of implementation…a broad and timely panorama of the field assembling an eminent roster of contributors.""-Jean-Marie Lehn, 1987 Noble Prize Winner in Chemistry

  11. Neural network applications

    Science.gov (United States)

    Padgett, Mary L.; Desai, Utpal; Roppel, T.A.; White, Charles R.

    1993-01-01

    A design procedure is suggested for neural networks which accommodates the inclusion of such knowledge-based systems techniques as fuzzy logic and pairwise comparisons. The use of these procedures in the design of applications combines qualitative and quantitative factors with empirical data to yield a model with justifiable design and parameter selection procedures. The procedure is especially relevant to areas of back-propagation neural network design which are highly responsive to the use of precisely recorded expert knowledge.

  12. Biomaterials and their applications

    CERN Document Server

    Reza Rezaie, Hamid; Öchsner, Andreas

    2015-01-01

    This short book presents an overview of different types of biomaterial such as bio ceramics, bio polymers, metals and bio composites, while especially focusing on nano biomaterials and their applications in different tissues. It provides a compact introduction to nano materials for drug delivery systems, tissue engineering and implants, while also reviewing essential trends in the biomaterial field over the last few decades and the latest developments.

  13. Hardware characteristic and application

    International Nuclear Information System (INIS)

    Gu, Dong Hyeon

    1990-03-01

    The contents of this book are system board on memory, performance, system timer system click and specification, coprocessor such as programing interface and hardware interface, power supply on input and output, protection for DC output, Power Good signal, explanation on 84 keyboard and 101/102 keyboard,BIOS system, 80286 instruction set and 80287 coprocessor, characters, keystrokes and colors, communication and compatibility of IBM personal computer on application direction, multitasking and code for distinction of system.

  14. Application of Auto CAD

    International Nuclear Information System (INIS)

    Park, Yong Un; Kim, Geun Ho

    1989-05-01

    This book has introduction to use this book and explanation of application on Auto CAD, which includes, sub directories, batch files, robot wrist, design of standard paper, title block, robort weld room, robert wrist joint, PC board, plant sym, electro, PID, machines, robots, bubbles, plant, schema, Pid, plant assembly, robots, dim plant, PL-ASSM, plotting line weight control, symbol drawing joint, Auto CAD using script file, set up of workout · MNU, workout MNU, ACAD, LSP and workout · MNU.

  15. Personal Network (PN) Applications

    DEFF Research Database (Denmark)

    Prasad, Ramjee; Skouby, K.

    2005-01-01

    The applications of PN will be realised under many scenarios where users can have access to their personal network all the time. This network will enable the user to share critical information, play games, control their home remotely, etc. All this will be achieved with seamless interworking...... and handover between networks and user devices. This paper presents an array of use case scenarios that validates the ubiquitous usage of PN....

  16. Personal network (PN) applications

    DEFF Research Database (Denmark)

    Prasad, R.; Skouby, Knud Erik

    2005-01-01

    The applications of PN will be realised under many scenarios where users can have access to their personal network all the time. This network will enable the user to share critical information, play games, control their home remotely, etc. All this will be achieved with seamless interworking...... and handover between networks and user devices. This paper presents an array of use case scenarios that validates the ubiquitous usage of PN....

  17. Android application security essentials

    CERN Document Server

    Rai, Pragati

    2013-01-01

    Android Application Security Essentials is packed with examples, screenshots, illustrations, and real world use cases to secure your apps the right way.If you are looking for guidance and detailed instructions on how to secure app data, then this book is for you. Developers, architects, managers, and technologists who wish to enhance their knowledge of Android security will find this book interesting. Some prior knowledge of development on the Android stack is desirable but not required.

  18. Nanotechnology and cancer applications

    OpenAIRE

    Gökdeniz, Mehmet; Akbaba, Muhsin; Nazlıcan, Ersin

    2018-01-01

    Applicationsof nanotechnology in various disciplines of medicine particularly cancer careare becoming increasingly popular so much so that the process of replacingtraditional health‑care by nanomedicine had already begun. Nanomedicine focuseson the formulations of imaging, diagnostic and therapeutic agents, which can becarried by biocompatible nanoparticles, for the purpose of cancer/ diseasemanagement.Common nanomaterials and devices applicable in cancer medicine are liposomes,polymeric‑mice...

  19. Optimization algorithms and applications

    CERN Document Server

    Arora, Rajesh Kumar

    2015-01-01

    Choose the Correct Solution Method for Your Optimization ProblemOptimization: Algorithms and Applications presents a variety of solution techniques for optimization problems, emphasizing concepts rather than rigorous mathematical details and proofs. The book covers both gradient and stochastic methods as solution techniques for unconstrained and constrained optimization problems. It discusses the conjugate gradient method, Broyden-Fletcher-Goldfarb-Shanno algorithm, Powell method, penalty function, augmented Lagrange multiplier method, sequential quadratic programming, method of feasible direc

  20. Graph theory with applications

    CERN Document Server

    Vasudev, C

    2006-01-01

    Salient Features Over 1500 problems are used to illustrate concepts, related to different topics, and introduce applications. Over 1000 exercises in the text with many different types of questions posed. Precise mathematical language is used without excessive formalism and abstraction. Care has been taken to balance the mix of notation and words in mathematical statements. Problem sets are stated clearly and unambiguously, and all are carefully graded for various levels of difficulty. This text has been carefully designed for flexible use.

  1. Applications of particle accelerators

    International Nuclear Information System (INIS)

    Barbalat, O.

    1994-01-01

    Particle accelerators are now widely used in a variety of applications for scientific research, applied physics, medicine, industrial processing, while possible utilisation in power engineering is envisaged. Earlier presentations of this subject, given at previous CERN Accelerator School sessions have been updated with papers contributed to the first European Conference on Accelerators in Applied Research and Technology (ECAART) held in September 1989 in Frankfurt and to the Second European Particle Accelerator Conference in Nice in June 1990. (orig.)

  2. Mimumes for SUBTLE applications

    Science.gov (United States)

    Lakhtakia, Akhlesh

    2014-08-01

    Inspired by natural multifunctionality, mimumes are microfibrous multifunctional metamaterials. Their microfibrosity engenders multifunctionality. Poly(p-xylylene) polymers that are currently used in bulk non-fibrous forms for packaging and tribological applications in electronic and biomedical arenas are excellent initial candidates to fabricate mimumes. In microfibrous forms, these polymers are expected to display simultaneous ultrasonic, biomedical, terahertz, light, and energy (SUBTLE) functionalities, thereby furthering the paradigm of design for system performance.

  3. Haar wavelets with applications

    CERN Document Server

    Lepik, Ülo

    2014-01-01

    This is the first book to present a systematic review of applications of the Haar wavelet method for solving Calculus and Structural Mechanics problems. Haar wavelet-based solutions for a wide range of problems, such as various differential and integral equations, fractional equations, optimal control theory, buckling, bending and vibrations of elastic beams are considered. Numerical examples demonstrating the efficiency and accuracy of the Haar method are provided for all solutions.

  4. Radioisotopes for medical applications

    International Nuclear Information System (INIS)

    Carr, S.

    1998-01-01

    For more than 3 decades, the Australian Nuclear Science and Technology Organisation has been the country's main supplier of radioisotopes for medical applications. The use of radioisotopes in medicine has revolutionised the diagnosis, management and treatment of many serious diseases such as cancer, heart disease and stroke. It is also beginning to play a key role in neurological disorders such as Parkinson and Alzheimers disease and epilepsy. More recently there has been considerable growth in the application of nuclear medicine to treat sport-related injuries - especially wrist, ankle and knees where more common techniques do not always enable accurate diagnosis. Australia is a recognised leader in nuclear medicine. This can be partially attributed to the close relationship between ANSTO and the medical community in providing opportunities to develop and evaluate new agents to support more effective patient care. A list of commercial isotopes produced in the reactor or the cyclotron and used in medical applications is given. Nuclear medicine plays an important role in the clinical environment and the timely supply of radioisotopes is a key element. ANSTO will continue to be the premier supplier of currently available and developing isotopes to support the health and well being of the Australian community

  5. [The applicability of results].

    Science.gov (United States)

    Marín-León, I

    2015-11-01

    The ultimate aim of the critical reading of medical literature is to use the scientific advances in clinical practice or for innovation. This requires an evaluation of the applicability of the results of the studies that have been published, which begins with a clear understanding of these results. When the studies do not provide sufficient guarantees of rigor in design and analysis, the conditions necessary for the applicability of the results are not met; however, the fact that the results are reliable is not enough to make it worth trying to use their conclusions. This article explains how carrying out studies in experimental or artificial conditions often moves them away from the real conditions in which they claim to apply their conclusions. To evaluate this applicability, the article proposes evaluating a set of items that will enable the reader to determine the likelihood that the benefits and risks reported in the studies will yield the least uncertainty in the clinical arena where they aim to be applied. Copyright © 2015 SERAM. Published by Elsevier España, S.L.U. All rights reserved.

  6. Applications of nuclear physics

    Science.gov (United States)

    Hayes, A. C.

    2017-02-01

    Today the applications of nuclear physics span a very broad range of topics and fields. This review discusses a number of aspects of these applications, including selected topics and concepts in nuclear reactor physics, nuclear fusion, nuclear non-proliferation, nuclear-geophysics, and nuclear medicine. The review begins with a historic summary of the early years in applied nuclear physics, with an emphasis on the huge developments that took place around the time of World War II, and that underlie the physics involved in designs of nuclear explosions, controlled nuclear energy, and nuclear fusion. The review then moves to focus on modern applications of these concepts, including the basic concepts and diagnostics developed for the forensics of nuclear explosions, the nuclear diagnostics at the National Ignition Facility, nuclear reactor safeguards, and the detection of nuclear material production and trafficking. The review also summarizes recent developments in nuclear geophysics and nuclear medicine. The nuclear geophysics areas discussed include geo-chronology, nuclear logging for industry, the Oklo reactor, and geo-neutrinos. The section on nuclear medicine summarizes the critical advances in nuclear imaging, including PET and SPECT imaging, targeted radionuclide therapy, and the nuclear physics of medical isotope production. Each subfield discussed requires a review article unto itself, which is not the intention of the current review; rather, the current review is intended for readers who wish to get a broad understanding of applied nuclear physics.

  7. Future applications of heterostructures

    Science.gov (United States)

    König, Ulf

    1996-01-01

    In this review the status and future of heterostructure devices is discussed. The author concentrates on III/V and Si/SiGe. Performance and applications are folded to the data and expectations of the micro- and opto-electronic market and to the traditional Si-mainstream. New trends, i.e. the SIA-roadmap, are checked how heterodevices can fit in. Only the most attractive candidates for applications are considered, i.e. the heterobipolar-, the hetero field effect-transistors, the resonant tunnel diode and to a less extent, some optoelectronic devices. Considered figures of merit are frequencies, transconductance, noise at high and low frequencies, threshold voltage, power delay, threshold current and quantum efficiencies. It is pointed out how to optimize those by material and design. Extrapolations to the future potential of heterodevices are made, just taking the claimed scaling of lateral dimensions into consideration. Field of applications are presented, where heterodevices offer exclusive qualities, i.e. high frequency transmission and sensors, and new mixed systems. In the case of logic the trend goes to nanoscaled devices and ICs targeting nanoelectronics beyond traditional electronics. Heterostructure layers allow a vertical nanoscaling and thus give an additional degree of freedom for designing and optimation. It is an attractive challenge for scientists and engineers to solve the related technological problems like thin, low thermal budget oxides, like defect free buffer layers etc. Special attention is put on Si/SiGe, which is now on an upswing in electronics and photonics.

  8. Panoramic lens applications revisited

    Science.gov (United States)

    Thibault, Simon

    2008-04-01

    During the last few years, innovative optical design strategies to generate and control image mapping have been successful in producing high-resolution digital imagers and projectors. This new generation of panoramic lenses includes catadioptric panoramic lenses, panoramic annular lenses, visible/IR fisheye lenses, anamorphic wide-angle attachments, and visible/IR panomorph lenses. Given that a wide-angle lens images a large field of view on a limited number of pixels, a systematic pixel-to-angle mapping will help the efficient use of each pixel in the field of view. In this paper, we present several modern applications of these modern types of hemispheric lenses. Recently, surveillance and security applications have been proposed and published in Security and Defence symposium. However, modern hemispheric lens can be used in many other fields. A panoramic imaging sensor contributes most to the perception of the world. Panoramic lenses are now ready to be deployed in many optical solutions. Covered applications include, but are not limited to medical imaging (endoscope, rigiscope, fiberscope...), remote sensing (pipe inspection, crime scene investigation, archeology...), multimedia (hemispheric projector, panoramic image...). Modern panoramic technologies allow simple and efficient digital image processing and the use of standard image analysis features (motion estimation, segmentation, object tracking, pattern recognition) in the complete 360° hemispheric area.

  9. Commercial applications for COIL

    Science.gov (United States)

    Solomon, Wayne C.; Carroll, David L.; King, D. M.; Fockler, L. A.; Stromberg, D. S.; Sexauer, M.; Milmoe, A.; Sentman, Lee H.

    2000-01-01

    The chemical oxygen-iodine laser (COIL) is a high power, fiber deliverable tool, which can be used for a number of different industrial applications. COIL is of particular interest because of its short fiber deliverable wavelength, high scaleable continuous wave power, and excellent material interaction properties. In past research the University of Illinois at Urbana-Champaign identified and decommissioning and decontamination (DD) of nuclear facilities as a primary focus for COIL technology. DD will be a major challenge in the coming decades. The use of a robotically driven fiber delivered cutting/ablation tool in contaminated areas promises to lower risks to workers for the DD mission. Further, the high cutting speed of COIL will significantly reduce the time required to cut contaminated equipment, reducing costs. The high power of COIL will permit the dismantling of thick stacks of piping and equipment as well as reactor vessels. COIL is very promising for the removal of material from contaminated surfaces, perhaps to depths thicker than an inch. Laser cutting and ablation minimizes dust and fumes, which reduces the required number of high efficiency particulate accumulator filters, thus reducing costly waste disposal. Other potential industrial applications for COIL are shipbuilding, automotive manufacturing, heavy machinery manufacturing, tasks requiring underwater cutting or welding, and there appear to be very promising applications for high powers lasers in the oil industry.

  10. Applications of nuclear physics

    International Nuclear Information System (INIS)

    Hayes-Sterbenz, Anna Catherine

    2017-01-01

    Today the applications of nuclear physics span a very broad range of topics and fields. This review discusses a number of aspects of these applications, including selected topics and concepts in nuclear reactor physics, nuclear fusion, nuclear non-proliferation, nuclear-geophysics, and nuclear medicine. The review begins with a historic summary of the early years in applied nuclear physics, with an emphasis on the huge developments that took place around the time of World War II, and that underlie the physics involved in designs of nuclear explosions, controlled nuclear energy, and nuclear fusion. The review then moves to focus on modern applications of these concepts, including the basic concepts and diagnostics developed for the forensics of nuclear explosions, the nuclear diagnostics at the National Ignition Facility, nuclear reactor safeguards, and the detection of nuclear material production and trafficking. The review also summarizes recent developments in nuclear geophysics and nuclear medicine. The nuclear geophysics areas discussed include geo-chronology, nuclear logging for industry, the Oklo reactor, and geo-neutrinos. The section on nuclear medicine summarizes the critical advances in nuclear imaging, including PET and SPECT imaging, targeted radionuclide therapy, and the nuclear physics of medical isotope production. Lastly, each subfield discussed requires a review article unto itself, which is not the intention of the current review; rather, the current review is intended for readers who wish to get a broad understanding of applied nuclear physics.

  11. Application of radiation imaging

    International Nuclear Information System (INIS)

    Sinha, Amar

    2004-01-01

    Imaging of radiation induced scintillations finds applications in many branches of science and technology. Over the years, many new applications of this technique have emerged. This has been possible particularly due to the development of new scintillating materials and new detectors using such scintillators. Nowhere has this development been more dramatic than in the field of century old medical imaging. Conventional film based technique has been replaced by several new detectors such as imaging plate, CCD based radiography system and flat panel detectors. In the field of x-ray crystallography replacement of film by imaging plate has reduced data reduction time from days to hours and finally use of CCD and ICCD based detectors have reduced this time to seconds and even less. In the field of non-destructive testing new techniques of 2D and 3D tomography, flow visualization has been possible due to rapid development in new scintillator and new electronic imaging detector systems incorporating such scintillators. This paper will review new frontiers in radiation imaging and describe some of the work being carried out at HPPD, BARC on various applications of radiation imaging using a variety of luminescent materials. (author)

  12. IMS applications analysis

    Energy Technology Data Exchange (ETDEWEB)

    RODACY,PHILIP J.; REBER,STEPHEN D.; SIMONSON,ROBERT J.; HANCE,BRADLEY G.

    2000-03-01

    This report examines the market potential of a miniature, hand-held Ion Mobility Spectrometer. Military and civilian markets are discussed, as well as applications in a variety of diverse fields. The strengths and weaknesses of competing technologies are discussed. An extensive Ion Mobility Spectrometry (IMS) bibliography is included. The conclusions drawn from this study are: (1) There are a number of competing technologies that are capable of detecting explosives, drugs, biological, or chemical agents. The IMS system currently represents the best available compromise regarding sensitivity, specificity, and portability. (2) The military market is not as large as the commercial market, but the military services are more likely to invest R and D funds in the system. (3) Military applications should be addressed before commercial applications are addressed. (4) There is potentially a large commercial market for rugged, hand-held Ion Mobility Spectrometer systems. Commercial users typically do not invest R and D funds in this type of equipment rather, they wait for off-the-shelf availability.

  13. Load Balancing Scientific Applications

    Energy Technology Data Exchange (ETDEWEB)

    Pearce, Olga Tkachyshyn [Texas A & M Univ., College Station, TX (United States)

    2014-12-01

    The largest supercomputers have millions of independent processors, and concurrency levels are rapidly increasing. For ideal efficiency, developers of the simulations that run on these machines must ensure that computational work is evenly balanced among processors. Assigning work evenly is challenging because many large modern parallel codes simulate behavior of physical systems that evolve over time, and their workloads change over time. Furthermore, the cost of imbalanced load increases with scale because most large-scale scientific simulations today use a Single Program Multiple Data (SPMD) parallel programming model, and an increasing number of processors will wait for the slowest one at the synchronization points. To address load imbalance, many large-scale parallel applications use dynamic load balance algorithms to redistribute work evenly. The research objective of this dissertation is to develop methods to decide when and how to load balance the application, and to balance it effectively and affordably. We measure and evaluate the computational load of the application, and develop strategies to decide when and how to correct the imbalance. Depending on the simulation, a fast, local load balance algorithm may be suitable, or a more sophisticated and expensive algorithm may be required. We developed a model for comparison of load balance algorithms for a specific state of the simulation that enables the selection of a balancing algorithm that will minimize overall runtime.

  14. Electrospinning and its applications

    International Nuclear Information System (INIS)

    Park, Jun-Seo

    2010-01-01

    Electrospinning is a process used to fabricate continuous nanoscale fibers with diameters in the sub-micrometer to nanometer range using a high-voltage power supply. Electrospun (e-spun) fibers and the non-woven webs manufactured from them have attracted considerable attention due to their outstanding characteristics, such as high porosity, small diameter, excellent pore interconnectivity and high surface-to-volume ratio. Because of the useful properties of e-spun fibers, many synthetic and natural polymers, including single and blended polymers, have been electrospun into fibers that can be employed in a variety of applications such as filtration and thermal insulation, and in the manufacture of protective clothing, sensors, conducting devices, wound dressings and scaffolds for tissue engineering. Utilizing the electrospinning technique and its product, some studies on its applications have been conducted in our lab. They included the fabrication of a conducting composite mat for electrical applications, an antibacterial web for a biomedical sector and PCM containing e-spun mat for energy storage

  15. Transactional Network Platform: Applications

    Energy Technology Data Exchange (ETDEWEB)

    Katipamula, Srinivas; Lutes, Robert G.; Ngo, Hung; Underhill, Ronald M.

    2013-10-31

    In FY13, Pacific Northwest National Laboratory (PNNL) with funding from the Department of Energy’s (DOE’s) Building Technologies Office (BTO) designed, prototyped and tested a transactional network platform to support energy, operational and financial transactions between any networked entities (equipment, organizations, buildings, grid, etc.). Initially, in FY13, the concept demonstrated transactions between packaged rooftop air conditioners and heat pump units (RTUs) and the electric grid using applications or "agents" that reside on the platform, on the equipment, on a local building controller or in the Cloud. The transactional network project is a multi-lab effort with Oakridge National Laboratory (ORNL) and Lawrence Berkeley National Laboratory (LBNL) also contributing to the effort. PNNL coordinated the project and also was responsible for the development of the transactional network (TN) platform and three different applications associated with RTUs. This document describes two applications or "agents" in details, and also summarizes the platform. The TN platform details are described in another companion document.

  16. Bayesian theory and applications

    CERN Document Server

    Dellaportas, Petros; Polson, Nicholas G; Stephens, David A

    2013-01-01

    The development of hierarchical models and Markov chain Monte Carlo (MCMC) techniques forms one of the most profound advances in Bayesian analysis since the 1970s and provides the basis for advances in virtually all areas of applied and theoretical Bayesian statistics. This volume guides the reader along a statistical journey that begins with the basic structure of Bayesian theory, and then provides details on most of the past and present advances in this field. The book has a unique format. There is an explanatory chapter devoted to each conceptual advance followed by journal-style chapters that provide applications or further advances on the concept. Thus, the volume is both a textbook and a compendium of papers covering a vast range of topics. It is appropriate for a well-informed novice interested in understanding the basic approach, methods and recent applications. Because of its advanced chapters and recent work, it is also appropriate for a more mature reader interested in recent applications and devel...

  17. Applicant Perspectives on the Otolaryngology Residency Application Process

    Science.gov (United States)

    2017-09-09

    82177.0 ’llrpproJlJ. Ct,r pvfJit r.,(ufe. f.li~+r:~n-1" ,,. vl\\l;.._.;tN. Applicant Perspectives on the Otolaryngology Residency Application...of the Department of Defense or its Components. • I have no financial conflicts of interest or sponsorship to disclose. Background • Applications...the Personal Statement Mandate on applications - Sources of advice and information -Suggestions for Improvement. Number of Programs Applied to

  18. Comparing Web Applications with Desktop Applications: An Empirical Study

    DEFF Research Database (Denmark)

    Pop, Paul

    2002-01-01

    of developing and using such applications. In this paper we present a comparison of web and desktop applications from the usability point of view. The comparison is based on an empirical study that investigates the performance of a group of users on two calendaring applications: Yahoo!Calendar and Microsoft...

  19. Laser Ablation for Medical Applications

    Science.gov (United States)

    Hayashi, Ken-Ichi

    Medical applications of laser are measurement, laser surgery, in-situ monitoring, and processing of medical devices. In this paper, author briefly reviews the trends of medical applications, describes some new applications, and then discuss about the future trends and problems of medical applications. At present, the domestic market of laser equipment for medical applications is nearly 1/10 of that for industrial applications, which has registered significant growth continuously. Laser surgery as a minimum invasive surgery under arthroscope is expected to decrease the pain of patients. Precise processing such as cutting and welding is suitable for manufacturing medical devices. Pulsed laser deposition has been successfully applied to the thin film coating. The corneal refractive surgery by ArF excimer laser has been widely accepted for its highly safe operation. Laser ablation for retinal implant in the visual prosthesis is one of the promising applications of laser ablation in medicine. New applications with femtosecond laser are expected in the near future.

  20. Android application development with Maven

    CERN Document Server

    Papapetrou, Patroklos

    2015-01-01

    Android Application Development with Maven is intended for Android developers or devops engineers who want to use Maven to effectively develop quality Android applications. It would be helpful, but not necessary, if you have some previous experience with Maven.

  1. Finite mathematics models and applications

    CERN Document Server

    Morris, Carla C

    2015-01-01

    Features step-by-step examples based on actual data and connects fundamental mathematical modeling skills and decision making concepts to everyday applicability Featuring key linear programming, matrix, and probability concepts, Finite Mathematics: Models and Applications emphasizes cross-disciplinary applications that relate mathematics to everyday life. The book provides a unique combination of practical mathematical applications to illustrate the wide use of mathematics in fields ranging from business, economics, finance, management, operations research, and the life and social sciences.

  2. Applications of nonlinear fiber optics

    CERN Document Server

    Agrawal, Govind

    2008-01-01

    * The only book describing applications of nonlinear fiber optics * Two new chapters on the latest developments: highly nonlinear fibers and quantum applications* Coverage of biomedical applications* Problems provided at the end of each chapterThe development of new highly nonlinear fibers - referred to as microstructured fibers, holey fibers and photonic crystal fibers - is the next generation technology for all-optical signal processing and biomedical applications. This new edition has been thoroughly updated to incorporate these key technology developments.The bo

  3. Ultrabroadband spectroscopy for security applications

    DEFF Research Database (Denmark)

    Engelbrecht, Sunniva; Berge, Luc; Skupin, Stefan

    2015-01-01

    Ultrabroadband spectroscopy is a promising novel approach to overcome two major hurdles which have so far limited the application of THz spectroscopy for security applications: the increased bandwidth enables to record several characteristic spectroscopic features and the technique allows...... evaluation of the technique for defense and civil security applications....

  4. Medical Professionals and Smartphone Applications.

    Science.gov (United States)

    Arunagiri, Varun; Parimala, M; Ragumani, P; Anbalagan, Kothai

    2017-06-01

    Ever since the advent of Smartphones, Smartphone applications (SAs) are revolutionizing the contemporary medicine. Smartphone application which was created in view of swift communications among the general public has now intruded the medical fraternity. But the ethics for using these applications to transfer patients' medical records through SA is bewildering among the medical professionals (MPs).

  5. Pervasive Application Rights Management Architecture

    OpenAIRE

    Dusparic, Ivana

    2005-01-01

    This dissertation describes an application rights management architecture that combines license management with digital rights management to provide an integrated platform for the specification, generation, delivery and management of application usage rights for pervasive computing environments. A new rights expression language is developed, extended from the existing language, ODRL, which allows the expression of mobile application usage rights and supports fine-grained usage ...

  6. Shopify application development

    CERN Document Server

    Larkin, Michael

    2014-01-01

    This is an easy-to follow manual that will guide you through the entire process of application development with Shopify, beginning with the installation and configuration of your local development environment for your app to the deployment of the app to Heroku. If you are a web developer or a designer who wants to extend Shopify stores by building apps, then this book is for you. A basic understanding of programming concepts and some familiarity with Shopify is all that is required to get started with Shopify app development.

  7. Industrial applications of cyclotrons

    International Nuclear Information System (INIS)

    Ditroi, F.

    1998-01-01

    Since the putting into operation of the Debrecen Cyclotron Laboratory with an MGC-20E (or U-103) machine, a lot of demands have been emerged on the practical exploitation of this facility. Since the cyclotron works at least in one half of its running time for medical purposes (isotope production), the rest can be devoted for fundamental research and practical applications. Special beam lines and laboratory facilities have been built for the purposes of materials investigation. These are mainly irradiation chambers, special irradiation facilities and sample holder/changers as well as special laboratory facilities for sample preparation and low background measurements

  8. Photocathodes in accelerator applications

    International Nuclear Information System (INIS)

    Fraser, J.S.; Sheffield, R.L.; Gray, E.R.; Giles, P.M.; Springer, R.W.; Loebs, V.A.

    1987-01-01

    Some electron accelerator applications require bursts of short pulses at high microscopic repetition rates and high peak brightness. A photocathode, illuminated by a mode-locked laser, is well suited to filling this need. The intrinsic brightness of a photoemitter beam is high; experiments are under way at Los Alamos to study the brightness of short bunches with high space charge after acceleration. A laser-illuminated Cs 3 Sb photoemitter is located in the first rf cavity of an injector linac. Diagnostics include a pepper-pot emittance analyzer, a magnetic spectrometer, and a streak camera

  9. Product Licenses Database Application

    CERN Document Server

    Tonkovikj, Petar

    2016-01-01

    The goal of this project is to organize and centralize the data about software tools available to CERN employees, as well as provide a system that would simplify the license management process by providing information about the available licenses and their expiry dates. The project development process is consisted of two steps: modeling the products (software tools), product licenses, legal agreements and other data related to these entities in a relational database and developing the front-end user interface so that the user can interact with the database. The result is an ASP.NET MVC web application with interactive views for displaying and managing the data in the underlying database.

  10. Android Studio application development

    CERN Document Server

    Zapata, Belén Cruz

    2013-01-01

    A practical guide, which will show you how to create Android applications using the new Google official IDE, Android Studio.If you are a developer who wants to learn the key features of Android Studio, and learn how to create their first app, this book is ideal for you! Developers interested in this book should be familiar with the object- oriented programming paradigm, and the Java programming language. It is also recommended that you understand the main characteristics of the Android mobile system.

  11. Nuclear cratering applications

    International Nuclear Information System (INIS)

    Williamson, M.M.

    1969-01-01

    The development of nuclear excavation technology is based on the promise that the relatively inexpensive energy available from thermonuclear explosives can be used to simultaneously break and move age quantities of rock and earth economically and safety. This paper discusses the economic and other advantages of using nuclear excavation for large engineering projects. A brief description of the phenomenology of nuclear excavation is given. Each of the several proposed general applications of nuclear excavation is discussed to include a few specific example of possible nuclear excavation projects. The discussion includes nuclear excavation for harbors, canals, terrain transits, aggregate production, mining and water resource development and conservation. (author)

  12. Unix Application Migration Guide

    CERN Document Server

    Microsoft. Redmond

    2003-01-01

    Drawing on the experience of Microsoft consultants working in the field, as well as external organizations that have migrated from UNIX to Microsoft® Windows®, this guide offers practical, prescriptive guidance on the issues you are likely to face when porting existing UNIX applications to the Windows operating system environment. Senior IT decision makers, network managers, and operations managers will get real-world guidance and best practices on planning and implementation issues to understand the different methods through which migration or co-existence can be accomplished. Also detailing

  13. Heroku cloud application development

    CERN Document Server

    Hanjura, Anubhav

    2014-01-01

    An easy-to-follow, hands-on guide that clearly explains the various components of the Heroku platform and provides step-by-step guidance as well as numerous examples on how to build and troubleshoot robust and scalable production-ready web applications on the Heroku platform.This book is intended for those who want to learn Heroku the right way. Perhaps you are new to Heroku or are someone who has heard about Heroku but have not built anything significant with it. You should have knowledge or familiarity with cloud computing and basic knowledge of database and network deployment.

  14. Games, theory and applications

    CERN Document Server

    Thomas, L C

    2011-01-01

    Anyone with a knowledge of basic mathematics will find this an accessible and informative introduction to game theory. It opens with the theory of two-person zero-sum games, two-person non-zero sum games, and n-person games, at a level between nonmathematical introductory books and technical mathematical game theory books. Succeeding sections focus on a variety of applications - including introductory explanations of gaming and meta games - that offer nonspecialists information about new areas of game theory at a comprehensible level. Numerous exercises appear with full solutions, in addition

  15. Cold regions isotope applications

    Energy Technology Data Exchange (ETDEWEB)

    Perrigo, L.D.; Divine, T.E.

    1976-04-01

    Pacific Northwest Laboratories (PNL) started the Cold Regions Isotope Applications Program in FY-1975 to identify special conditions in the Arctic and similar geographic areas (Cold Regions) where radioisotope power, heater, or sterilization systems would be desirable and economically viable. Significant progress was made in the first year of this program and all objectives for this initial 12-month period were achieved. The major conclusions and recommendations resulting for this effort are described below. The areas of interest covered include: radiosterilization of sewage; heating of septic tanks; and radioisotope thermoelectric generators as power sources for meteorological instruments and navigational aids. (TFD)

  16. Web Application Frameworks

    Directory of Open Access Journals (Sweden)

    Maria Cristina ENACHE

    2015-12-01

    Full Text Available As modern browsers become more powerful with rich features, building full-blown web applications in JavaScript is not only feasible, but increasingly popular. Based on trends on HTTP Archive, deployed JavaScript code size has grown 45% over the course of the year. MVC offers architectural benefits over standard JavaScript — it helps you write better organized, and therefore more maintainable code. This pattern has been used and extensively tested over multiple languages and generations of programmers. It's no coincidence that many of the most popular web programming frameworks also encapsulate MVC principles: Django, Ruby on Rails, CakePHP, Struts, or Laravell.

  17. Optimization Foundations and Applications

    CERN Document Server

    Miller, H Ronald

    2011-01-01

    A thorough and highly accessible resource for analysts in a broad range of social sciences. Optimization: Foundations and Applications presents a series of approaches to the challenges faced by analysts who must find the best way to accomplish particular objectives, usually with the added complication of constraints on the available choices. Award-winning educator Ronald E. Miller provides detailed coverage of both classical, calculus-based approaches and newer, computer-based iterative methods. Dr. Miller lays a solid foundation for both linear and nonlinear models and quickly moves on to dis

  18. Nonextensive entropy interdisciplinary applications

    CERN Document Server

    Tsallis, Constantino

    2004-01-01

    A great variety of complex phenomena in many scientific fields exhibit power-law behavior, reflecting a hierarchical or fractal structure. Many of these phenomena seem to be susceptible to description using approaches drawn from thermodynamics or statistical mechanics, particularly approaches involving the maximization of entropy and of Boltzmann-Gibbs statistical mechanics and standard laws in a natural way. The book addresses the interdisciplinary applications of these ideas, and also on various phenomena that could possibly be quantitatively describable in terms of these ideas.

  19. Microsystems for Space Applications

    Directory of Open Access Journals (Sweden)

    B. Palán

    2000-01-01

    Full Text Available Recent progress in microsystems technologies make them suitable for the space research and development due to their low volume, low mass, low power consumption, leading to reduced mission cost. The most interesting approach is using standard technologies with additional post-processing steps to realize sensors and actuators together with signal processing circuits. This paper summarises some aspects and difficulties of the space environment. The radiation effects in space are described and damage on CMOS structures are explained. Design methodologies for hardening microsystems and MOS based circuits against these effects are presented. Some examples of microsystems examples for space applications fabricated by researches world-wide are given.

  20. Application testing with Capybara

    CERN Document Server

    Robbins, Matthew

    2013-01-01

    Start performing integration testing with Capybara immediately. This book will get you up and running quickly and assumes no knowledge or experience of the technology.This book is for developers and testers who have had some exposure to Ruby but who want to know how to test their applications using Capybara and its compatible drivers, such as Selenium-Webdriver and Rack-Test. The examples are deliberately kept simple and example HTML mark-up is always included so that you can copy the examples to practice and experiment on your own machine.

  1. Best Sale Mobile Application

    OpenAIRE

    Chittugnanamoorthy, Balakumar

    2014-01-01

    The aim of this thesis was to find a best way to advertise short-term sales and reduce paper waste. Another aim was to help the seller to identify a potential customer for a specific product, by means of providing a number of people accessing an advertisement. A mobile phone is one of the widely used electronic devices by many people. Modern mobile phones support a good internet connection. Also, people carry their mobile devices with them even outside their homes. So a mobile application ...

  2. Visual languages and applications

    CERN Document Server

    Zhang, Kang

    2010-01-01

    Visual languages have long been a pursuit of effective communication between human and machine. With rapid advances of the Internet and Web technology, human-human communication through the Web or electronic mobile devices is becoming more and more prevalent. Visual Languages and Applications is a comprehensive introduction to diagrammatical visual languages. This book discusses what visual programming languages are, and how such languages and their underlying foundations can be usefully applied to other fields in computer science. It also covers a broad range of contents from the underlying t

  3. Industrial applications of radiations

    International Nuclear Information System (INIS)

    Gallien, C.L.

    1988-01-01

    Radiation processing refers to the use of ionizing radiation to initiate chemical or biological changes in various materials as a substitute for conventional thermal or chemical processes. The method was inroduced in the industrial field 30 years ago and is now being widely used for numerous applications, among which industrial radiography, polymer modification, sterilization or decontamination, and food preservation. Both electron beam accelerators and gamma sources can be used, depending mainly of the amount of radiation and the penetration required. Radiation processing presents an increasing economical importance; in 1986 the market volume of ionized products ranged 3 billion $ [fr

  4. Synchrotron radiation and applications

    International Nuclear Information System (INIS)

    Nenner, I.; Dexpert, H.; Bessiere, M.

    1989-01-01

    Synchrotron radiation gives a very large wavelength spectra from infrared to X-rays. The continuous spectra in the far ultraviolet and X rays and also the brightness of the source enlarge the studies of structural and electronic properties of matter. In a brief review of main applications, the paper presents more particularly absorption, diffusion and diffraction phenomena. Examples taken in inorganic chemistry and condensed matter physics show the power of X-ray aborption spectroscopy and electron spectroscopy methods (angular analysis of photoelectrons and mass spectroscopy) for the study of surfaces and solids. 51 refs [fr

  5. Applications of stable isotopes

    International Nuclear Information System (INIS)

    Letolle, R.; Mariotti, A.; Bariac, T.

    1991-06-01

    This report reviews the historical background and the properties of stable isotopes, the methods used for their measurement (mass spectrometry and others), the present technics for isotope enrichment and separation, and at last the various present and foreseeable application (in nuclear energy, physical and chemical research, materials industry and research; tracing in industrial, medical and agronomical tests; the use of natural isotope variations for environmental studies, agronomy, natural resources appraising: water, minerals, energy). Some new possibilities in the use of stable isotope are offered. A last chapter gives the present state and forecast development of stable isotope uses in France and Europe

  6. Ultracapacitors for automotive applications

    Energy Technology Data Exchange (ETDEWEB)

    Ashtiani, Cyrus [DaimlerChrysler Corp., CIMS 526-00-00, 1870 Technology Dr., Troy, MI 48083 (United States); Wright, Randy; Hunt, Gary [Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 834415-3830 (United States)

    2006-03-21

    In response to a growing consensus in the auto industry that ultracapacitors can potentially play a key role in the modern vehicle power distribution network, a task force was created at the United States Advanced Battery Consortium (USABC) to tackle issues facing the fledging industry. The task force embarked on first developing and establishing standards for performance and abuse tolerance of ultracapacitors in collaboration with the U.S. Department of Energy and National Labs. Subsequently, potential applications in the automotive industry were identified and a consensus requirement specification was drawn as a development guide for the industry. (author)

  7. Electronic circuits fundamentals & applications

    CERN Document Server

    Tooley, Mike

    2015-01-01

    Electronics explained in one volume, using both theoretical and practical applications.New chapter on Raspberry PiCompanion website contains free electronic tools to aid learning for students and a question bank for lecturersPractical investigations and questions within each chapter help reinforce learning Mike Tooley provides all the information required to get to grips with the fundamentals of electronics, detailing the underpinning knowledge necessary to appreciate the operation of a wide range of electronic circuits, including amplifiers, logic circuits, power supplies and oscillators. The

  8. Applications in solid mechanics

    DEFF Research Database (Denmark)

    Ølgaard, Kristian Breum; Wells, Garth N.

    2012-01-01

    Problems in solid mechanics constitute perhaps the largest field of application of finite element methods. The vast majority of solid mechanics problems involve the standard momentum balance equation, posed in a Lagrangian setting, with different models distinguished by the choice of nonlinear...... or linearized kinematics, and the constitutive model for determining the stress. For some common models, the constitutive relationships are rather complex. This chapter addresses a number of canonical solid mechanics models in the context of automated modeling, and focuses on some pertinent issues that arise...

  9. Metagenomics and Applications

    Directory of Open Access Journals (Sweden)

    L Rafati

    2016-11-01

    Full Text Available Introduction: Bacteria are a group of microorganisms which in contrast to their diversity in nature, only very few of them can be grown and isolated in the current standard laboratories. Metagenomics as a new field of research, during the last decade has worked on clarification of the genomes of the non-cultured microbes and researchers around the world with serious study of this group of bacteria, looking for new compounds such as new antibiotics, anti-cancer agents, new enzymes and biomolecules. Methods: This article is reviews study which with study of Texts and Internet and handy browsing of key words from reliable scientific resources and sites amongst: Google Scholar, Pub med, Science direct, Sid and Scopus in the years 2000 to 2013 were collected and studied. Results: The data collection instrument in the study includes all printed metagenomics related texts. Although, nowadays metagenomics is used to screen samples but now as a perfect technique beside the medium application and other traditional techniques will have better position. The highest usage of metagenomics is in clinical cases where with conventional techniques can't be discovered microbial reasons. So for tests and analyze information need to skilled scientists. Conclusion: This paper focuses on some of the latest achievements of Metagenomics and its application in new drugs, detection of enzymes, potential of biotechnology and environment.

  10. Surety applications in transportation

    Energy Technology Data Exchange (ETDEWEB)

    Matalucci, R.V.; Miyoshi, D.S.

    1998-01-01

    Infrastructure surety can make a valuable contribution to the transportation engineering industry. The lessons learned at Sandia National Laboratories in developing surety principles and technologies for the nuclear weapons complex and the nuclear power industry hold direct applications to the safety, security, and reliability of the critical infrastructure. This presentation introduces the concepts of infrastructure surety, including identification of the normal, abnormal, and malevolent threats to the transportation infrastructure. National problems are identified and examples of failures and successes in response to environmental loads and other structural and systemic vulnerabilities are presented. The infrastructure surety principles developed at Sandia National Laboratories are described. Currently available technologies including (a) three-dimensional computer-assisted drawing packages interactively combined with virtual reality systems, (b) the complex calculational and computational modeling and code-coupling capabilities associated with the new generation of supercomputers, and (c) risk-management methodologies with application to solving the national problems associated with threats to the critical transportation infrastructure are discussed.

  11. Application of radiation nowadays

    International Nuclear Information System (INIS)

    Habibah Adnan

    2009-01-01

    Despite of scientist know about radiation since 1890, but they have successfully developed many of application to help human life. Now, we can see that radiation was applied in medical, academic, industrial, and generating electricity. Besides that, radiations also have other applications that can help in agriculture activities, archaeology, legislation, geology, space exploration and many more. In hospital, doctor use nuclear medicine to trace, monitor and save almost thousands of people every year. According to research, 7 out of 10 American citizens had already use this services at least once in their life. Universities, college, secondary school, research center also use nuclear material in their laboratory. For example, through research, radiation can help in plants study, agriculture technique, soils study and others. Industrial sector are one sector that applied radiation widely. For example, radiation can kill almost 80 % bacteria or dangerous microorganism in food or export products. Nowadays, radiation cannot be curtailed although it can give more benefit more than risk. It depends on how we manage it.

  12. Environmental applications for biosurfactants

    International Nuclear Information System (INIS)

    Mulligan, Catherine N.

    2005-01-01

    Biosurfactants are surfactants that are produced extracellularly or as part of the cell membrane by bacteria, yeasts and fungi. Examples include Pseudomonas aeruginosa which produces rhamnolipids, Candida (formerly Torulopsis) bombicola, one of the few yeasts to produce biosurfactants, which produces high yields of sophorolipids from vegetable oils and sugars and Bacillus subtilis which produces a lipopeptide called surfactin. This review includes environmental applications of these biosurfactants for soil and water treatment. Biosurfactant applications in the environmental industries are promising due to their biodegradability, low toxicity and effectiveness in enhancing biodegradation and solubilization of low solubility compounds. However, more information is needed to be able to predict and model their behaviour. Full scale tests will be required. The role of biosurfactants in natural attenuation processes has not been determined. Very little information is available concerning the influence of soil components on the remediation process with biosurfactants. As most of the research until now has been performed with rhamnolipids, other biosurfactants need to be investigated as they may have more promising properties. - More information is needed to be able to predict and model the behaviour of biosurfactants

  13. Environmental applications for biosurfactants

    Energy Technology Data Exchange (ETDEWEB)

    Mulligan, Catherine N. [Department Building, Civil and Environmental Engineering, Concordia University, 1455 de Maisonneuve Boulevard W., Montreal, Quebec, H3G 1M8 (Canada)]. E-mail: mulligan@civil.concordia.ca

    2005-01-01

    Biosurfactants are surfactants that are produced extracellularly or as part of the cell membrane by bacteria, yeasts and fungi. Examples include Pseudomonas aeruginosa which produces rhamnolipids, Candida (formerly Torulopsis) bombicola, one of the few yeasts to produce biosurfactants, which produces high yields of sophorolipids from vegetable oils and sugars and Bacillus subtilis which produces a lipopeptide called surfactin. This review includes environmental applications of these biosurfactants for soil and water treatment. Biosurfactant applications in the environmental industries are promising due to their biodegradability, low toxicity and effectiveness in enhancing biodegradation and solubilization of low solubility compounds. However, more information is needed to be able to predict and model their behaviour. Full scale tests will be required. The role of biosurfactants in natural attenuation processes has not been determined. Very little information is available concerning the influence of soil components on the remediation process with biosurfactants. As most of the research until now has been performed with rhamnolipids, other biosurfactants need to be investigated as they may have more promising properties. - More information is needed to be able to predict and model the behaviour of biosurfactants.

  14. Novel oral laser applications

    Science.gov (United States)

    Yousif, A.; Strassl, M.; Beer, F.; Verhagen, L.; Wittschier, M.; Wintner, E.

    2007-03-01

    In dental hard tissue ablation, ultra-short laser pulses have proven sufficiently their potential for material ablation with negligible collateral damage providing many advantages. The absence of micro-cracks and the possibility to avoid overheating of the pulp during dental cavity preparation may be among the most important issues, the latter opening up an avenue for potential painless treatment. Beside the evident short interaction time of laser radiation with the irradiated tissue, scanning of the ultra-short pulse trains turned out to be crucial for ablating cavities of required quality and shape. Additionally, long-pulsed laser systems have demonstrated successfully their suitability for decontamination purposes. In this paper, an overview of different indications for laser application in dental therapies in both pulse regimes is presented. A special focus is set on the decontamination of dental implants in periimplantitis therapy. Having employed commercially available long pulse systems for dental applications and ultra-short 330 fs pulses, we present first results for temperature development and corresponding ablation thresholds for dental implants, as in the future more gentle implant cleaning by ultra-short laser pulses could become of interest.

  15. Berkovich spaces and applications

    CERN Document Server

    Favre, Charles; Nicaise, Johannes

    2015-01-01

    We present an introduction to Berkovich’s theory of non-archimedean analytic spaces that emphasizes its applications in various fields. The first part contains surveys of a foundational nature, including an introduction to Berkovich analytic spaces by M. Temkin, and to étale cohomology by A. Ducros, as well as a short note by C. Favre on the topology of some Berkovich spaces. The second part focuses on applications to geometry. A second text by A. Ducros contains a new proof of the fact that the higher direct images of a coherent sheaf under a proper map are coherent, and B. Rémy, A. Thuillier and A. Werner provide an overview of their work on the compactification of Bruhat-Tits buildings using Berkovich analytic geometry. The third and final part explores the relationship between non-archimedean geometry and dynamics. A contribution by M. Jonsson contains a thorough discussion of non-archimedean dynamical systems in dimension 1 and 2. Finally a survey by J.-P. Otal gives an account of Morgan-Shalen's the...

  16. Oracle Application Express 4 Recipes

    CERN Document Server

    Zehoo, Edmund

    2011-01-01

    Oracle Application Express 4 Recipes provides an example-based approach to learning Application Express - the ground-breaking, rapid application development platform included with every Oracle Database license. The recipes format is ideal for the quick-study who just wants a good example or two to kick start their thinking and get pointed in the right direction. The recipes cover the gamut of Application Express development. Author and Application Express expert Edmund Zehoo shows how to create data entry screens, visualize data in the form of reports and charts, implement validation and back-

  17. Direct application of geothermal energy

    Energy Technology Data Exchange (ETDEWEB)

    Reistad, G.M.

    1980-01-01

    An overall treatment of direct geothermal applications is presented with an emphasis on the above-ground engineering. The types of geothermal resources and their general extent in the US are described. The potential market that may be served with geothermal energy is considered briefly. The evaluation considerations, special design aspects, and application approaches for geothermal energy use in each of the applications are considered. The present applications in the US are summarized and a bibliography of recent studies and applications is provided. (MHR)

  18. Applications of high power microwaves

    International Nuclear Information System (INIS)

    Benford, J.; Swegle, J.

    1993-01-01

    The authors address a number of applications for HPM technology. There is a strong symbiotic relationship between a developing technology and its emerging applications. New technologies can generate new applications. Conversely, applications can demand development of new technological capability. High-power microwave generating systems come with size and weight penalties and problems associated with the x-radiation and collection of the electron beam. Acceptance of these difficulties requires the identification of a set of applications for which high-power operation is either demanded or results in significant improvements in peRFormance. The authors identify the following applications, and discuss their requirements and operational issues: (1) High-energy RF acceleration; (2) Atmospheric modification (both to produce artificial ionospheric mirrors for radio waves and to save the ozone layer); (3) Radar; (4) Electronic warfare; and (5) Laser pumping. In addition, they discuss several applications requiring high average power than border on HPM, power beaming and plasma heating

  19. Characterization of beta radiation fields using radiochromic films; Caracterizacao de campos de radiacao beta utilizando filmes radiocromicos

    Energy Technology Data Exchange (ETDEWEB)

    Benavente, Jhonny A.; Silva, Teogenes A. da, E-mail: jabc@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil). Programa de Pos-Graduacao em Ciencia e Tecnologia das Radiacoes, Minerais e Materiais; Meira-Belo, Luiz C.; Reynaldo, Sibele R. [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2011-07-01

    The objective of this work was to study the response of radiochromic films for beta radiation fields in terms of absorbed dose. The reliability of the EBT model Gafchromic radiochromic film was studied. A 9800 XL model Microtek, transmission scanner, a 369 model X-Rite optical densitometer and a Mini 1240 Shimadzu UV spectrophotometer were used for measurement comparisons. Calibration of the three systems was done with irradiated samples of radiochromic films with 0.1; 0.3; 0.5; 0.8; 1.0; 1.5; 2.0; 2.5; 3.0; 3.5; 4.5 e 5.0 Gy in beta radiation field from a Sr-90/Y-90 source. Calibration was performed by establishing a correlation between the absorbed dose values and the corresponding radiochromic responses. Results showed significant differences in the absorbed dose values obtained with the three methods. Absorbed dose values showed errors from 0.6 to 4.4%, 0.3 to 31.8% and 0.2 to 47.3% for the Microtek scanner, the X-Rite Densitometer and the Shimadzu spectrophotometer, respectively. Due to the easy acquisition and use for absorbed dose measurements, the densitometer and the spectrophotometer showed to be suitable techniques to evaluate radiation dose in relatively homogeneous fields. In the case of inhomogeneous fields or for a two dimension mapping of radiation fields to identify anisotropies, the scanner technique is the most recommended. (author)

  20. Clay characterization for making pressed and burned blocks; Caracterizacao da argila para confeccao de blocos prensados e queimados

    Energy Technology Data Exchange (ETDEWEB)

    Alexandre, J.; Silva, C.L. de A.P. e, E-mail: jonas@uenf.br, E-mail: caio_lobato_414@hotmail.com [Universidade Estadual do Norte Fluminense Darcy Ribeiro (UENF), Campos dos Goytacazes, RJ (Brazil)

    2012-07-01

    The municipality of Campos dos Goytacazes, located in the state of Rio de Janeiro, at 275 km from the capital, are the largest industrial ceramic state and he has over 100 unionized industries. The production of these industries is based on tiles, building blocks and bricks. Seeking the improvement and diversification of production, the North Fluminense State University has 18 years working in partnership with local industry, with students and teachers. One of the researches is the production of blocks pressed and burned. In this work are presented in many lab tests performed, morphology and some of technological properties. (author)

  1. Characterization of clay used for red ceramic fabrication; Caracterizacao de argila utilizada para fabricacao de ceramica vermelha

    Energy Technology Data Exchange (ETDEWEB)

    Pereira, P.S.; Morais, A.S.C.; Caldas, T.C.C.; Monteiro, S.N.; Vieira, C.M.F. [Universidade Estadual do Norte Fluminense Darcy Ribeiro (LAMAV/UENF), Campos dos Goytacazes, RJ (Brazil). Laboratorio de Materiais Avancados; Ribeiro, M.M., E-mail: patriciasp_@hotmail.com [Instituto Federal Fluminense (IFF), Campos dos Goytacazes, RJ (Brazil)

    2011-07-01

    The objective of this work is to characterize a clay used in the red ceramics fabrication, from Campos dos Goytacazes north of the State of Rio de Janeiro. The clay was submitted for physical, chemical and mineralogical tests. The results showed that the clay has a high content of clay minerals with kaolinitic predominance, high loss on ignition and low flux oxides. It is recommended that this clay is mixed with non-plastic materials. (author)

  2. Dosimetric characterization of a commercial two-dimensional array detector; Caracterizacao dosimetrica de um detector matricial bidimensional comercial

    Energy Technology Data Exchange (ETDEWEB)

    Gialluisi, Bruno L.; Santos, Gabriela R. dos; Sales, Camila P. de; Resende, Guilherme R.A.; Habitzreuter, Angela B.; Rodrigues, Laura N., E-mail: brunogialluisi@gmail.com [Universidade de Sao Paulo (HCFMRP/USP), Sao Paulo, SP (Brazil). Hospital das Clinicas. Servico de Radioterapia

    2013-04-15

    This paper investigates the dosimetric characteristics and performance of an array detector commercially available. The device is the I'mRT MatriXX® which is a two-dimensional detector array used in the verification of complex radiotherapy plans. It consists of 1,020 parallel plate ion chamber arranged in a 32x32 grid. Dose linearity was studied and its response was linear within the range of 5 to 1000 MU (R{sup 2} = 1). Dose rate dependence showed a maximum deviation of 0,62% comparatively with readings to 320 cGy/min. The detector stability was verified through repeated irradiations. Output factors matched well with measurements made with a Farmer chamber with an average deviation of 1,54%. The detector's effective point of measurement was determined and the inverse square law was also verified with a percentage deviation smaller than 3%. The results show that this detector can be used for quality control in IMRT thus reducing the time spent in the dosimetric verification of radiation fields. (author)

  3. Photovoltaic solar panels of crystalline silicon: characterization and separation; Paineis solares fotovoltaicos de silicio cristalino: caracterizacao e separacao

    Energy Technology Data Exchange (ETDEWEB)

    Diasa, P.R.; Benevita, M.G.; Veita, H.M., E-mail: pablo.dias@ufrgs.br [Universidade Federal do Rio Grande do Sul (LACOR/UFRGS), Porto Alegre, RS (Brazil). Laboratorio de Corrosao, Protecao e Reciclagem de Materiais

    2014-07-01

    The search for alternative power generation sources has been intensified in recent years. One of these alternatives is solar energy, since it is a virtually inexhaustible source and generates relatively small environmental impact compared to other traditional generation sources. The collection of solar energy and its conversion into thermal or electrical energy is only possible through the use of photovoltaic panels. These panels have a limited lifespan and will eventually be replaced by new ones. Thus, in the near future, large amounts of solar modules can be discarded as waste electronics. In order to retrieve important raw materials, reducing production costs and environmental impacts, recycling such materials is important. In this paper, photovoltaic module components were characterized through visual inspection, FRX, EDS and AAS. The glass was identified as ordinary glass (soda-lime glass), which allows reuse without any previous treatment and the metallic filaments were identified as tin- lead coated copper. (author)

  4. Characterization and stabilization of suspension of bovine bone ash; Caracterizacao e estabilizacao de suspensao de po de ossos bovinos

    Energy Technology Data Exchange (ETDEWEB)

    Carus, L.A.; Bento, L.; Takimi, A.S.; Braganca, S.R., E-mail: laucarus@gmail.com [Universidade Federal do Rio Grande do Sul (UFRGS), Porto Alegre, RS (Brazil). Programa de Pos-Graduacao em Engenharia de Minas Metalurgica e de Materiais

    2012-07-01

    The bovine bone powder is the main component in the production of bone china, which is known to be one of the finest and most expensive tableware. This special type of porcelain has unique aesthetic characteristics, among which stands out the whiteness, translucency and brightness. The properties of this porcelain, as well as its manufacture, depend on the characteristics of the bone ash. In this study the rheological properties of the suspensions using exclusively bovine bone ash were evaluated by testing the influence of the concentration of solids in suspension, the calcination temperature and the use of dispersing agents. It was found that the powder calcination temperature affects the rheology of the suspension by lowering the viscosity. (author)

  5. Characterization of montmorillonite-Ca to use polymer nanocomposites; Caracterizacao de argila esmectitica modificada visando seu uso em nanocompositos polimericos

    Energy Technology Data Exchange (ETDEWEB)

    Neto, Joao E.; Neto, Jose C.M.; Campo, Eduardo R.B. del, E-mail: joao_evengelista_neto@yahoo.com [Universidade do Estado do Amazonas (UEAM), Manaus, AM (Brazil). Coordenacao de Engenharia de Materiais; Nascimento, Nayra R. do [Universidade Estadual de Campinas (UNICAMP), SP (Brazil). Departamento de Engenharia de Materiais e Bioprocessos; Diaz, Francisco Rolando Valenzuela [Universidade de Sao Paulo (USP), SP (Brazil). Departamento de Engenharia Metalurgica e Materiais

    2015-07-01

    Bentonite is an important type of industrial clays due to its rheological properties or accession that are dependent on its high hydrophilicity. This clay has the capability of being modified with organic compounds by treatment with ammonium quaternary salts. After the clay treatment with these salts it presents a high degree of swelling property in organic liquids. Due to this swelling characteristics, the bentonite can be used in dispersions of organic liquids viscous and thixotropic. Another focus of interest this clay is in industry and academia because of its potential use in the adsorption of toxic substances and as fillers in nanocomposites clay / polymer. The objective of this study is to characterize a Cuban calcium bentonite modified with sodium dodecyl sulfate. The clay was characterized by X-ray diffraction, particle size analysis by laser diffraction and scanning electron microscopy. (author)

  6. Synthesis and characterization of hydroxyapatite-doped silver nanoparticles; Sintese e caracterizacao de hidroxiapatita dopada com nanoparticulas de prata

    Energy Technology Data Exchange (ETDEWEB)

    Andrade, Flavio Augusto Cavadas da Silva; Rollo, Joao Manuel Domingos de Almeida, E-mail: flavio.andrade@usp.br [Universidade de Sao Paulo (EESC/FMRP/IQSC/USP), Sao Carlos, SP (Brazil). Programa de Pos-Graduacao Interunidades Bioengenharia; Rigo, Eliana Cristina da Silva; Vercik, Andres; Vercik, Luci Cristina de Oliveira; Valencia, German Ayala; Ferreira, Leticcia Gaviao [Universidade de Sao Paulo (USP), Pirassununga, SP (Brazil). Faculdade de Zootecnia e Engenharia de Alimentos. Departamento de Ciencias Basicas

    2012-07-01

    Hydroxyapatite-doped silver nanoparticles was obtained by immersing the powder in increasing dilutions of a solution containing AGNPS which were synthesized in different times and were characterized by UV-vis spectroscopy. The X-ray diffraction (XRD)studies demonstrate no change in the major phase of HA. Scanning Electron Microscopy (SEM) revealed morphological characteristics of powders after doping and the presence of silver was confirmed by energy dispersive X-ray (EDAX) analysis.The antibacterial effect of the doped powders was evaluated using strain of Staphylococcus aureus by disc-diffusion test. The zone of inhibition was found to vary with the amount of silver nanoparticle in the doped powder even for low concentrations of AgNPs. These results indicate that the method of immersion hydroxyapatite in solutions containing AgNPs is promising to obtain bioactive materials with low cytotoxicity and antibacterial effects. (author)

  7. Characterization of granite waste for use in red ceramic; Caracterizacao de residuo de granito para utilizacao em ceramica vermelha

    Energy Technology Data Exchange (ETDEWEB)

    Aguiar, M.C.; Monteiro, S.N.; Vieira, C.M.F., E-mail: mari@uenf.br [Universidade Estadual do Norte Fluminense (UENF/LAMAV), Campos dos Goytacazes, RJ (Brazil). Laboratorio de Materiais Avancados; Borlini, M.C. [Centro de Tecnologia Mineral (CETEM), Cachoeiro de Itapemirim, ES (Brazil). Centro Avancado

    2011-07-01

    This work aims to study the characterization of the granite waste from the city of Santo Antonio de Padua-RJ for the use in red ceramic. The chemical, physical and morphological characterization of the waste was performed by chemical analysis, X-ray diffraction, particle size distribution, thermal analysis and scanning electron microscopy (SEM). The results indicated that this waste is a material with great potential to be used as a component of ceramic body due to its capacity to act as flux during the firing, and to improve the properties of the ceramic when is incorporate. (author)

  8. Synthesis and characterization of tungsten or calcium doped PZT ceramics; Sintese e caracterizacao do PZT dopado com W ou Ca

    Energy Technology Data Exchange (ETDEWEB)

    Santos, D.M.; Caracas, L.B.; Noronha, R.G.; Santos, M.M.T. dos [Universidade Federal do Maranhao (UFMA), Sao Luis, MA (Brazil). Dept. de Desenho e Tecnologia. Curso de Desenho Industrial; Paiva-Santos, C.O., E-mail: denilson@ufma.b [Universidade Estadual Paulista (IQ/UNESP), Araraquara, SP (Brazil). Inst. de Quimica

    2009-07-01

    Pure and doped (tungsten or calcium) PZT ceramics were prepared by association of the polymeric precursor and partial oxalate method. The phase formation was investigated by thermal analysis (TG/DSC) and X-ray diffraction (XRD). The affect of W or Ca doping PZT and their electrical properties was evaluated. Substitution of W by Ti and Ca by Pb leads to an increase of Curie temperature and broadening of dielectric constant. A typical hysteresis loop was observed at room temperature and the remnant polarization was increased with the content of W and Ca. (author)

  9. Electrochemical characterization of proton exchange membrane fuel cells; Caracterizacao eletroquimica de celulas a combustivel de membrana polimerica trocadora de protons

    Energy Technology Data Exchange (ETDEWEB)

    Furtado, Jose Geraldo de Melo; Serra, Eduardo Torres [Centro de Pesquisas de Energia Eletrica (CEPEL), Rio de Janeiro, RJ (Brazil)]. E-mail: furtado@cepel.br; Codeceira Neto, Alcides [Companhia HidroEletrica do Sao Francisco (CHESF), Recife, PE (Brazil)

    2008-07-01

    This paper describes the electrochemical behavior of a proton exchange membrane fuel cell in function of temperature and time of operation. Different polarization phenomena are considered in the 30 to 70 deg C temperature range, as well as the degradation of electrochemical behavior of the fuel cell analyzed up to 1260 hours of operation. The results show that there is a tendency for the experimental values approaching the theoretical as it increases the temperature of the membrane electrolyte. The electrochemical behavior of the PEMFC studied proved to be less stable at 70 deg C. On the other hand, at 30 deg C the fuel cell performance proved to be considerably lower than at other temperatures. Also, it was found that in certain current ranges occurs greater overlay in potential-current curves, and in some cases reversing between these curves depending on the electric current required for the data obtained at 60 and 70 deg C, indicating, perhaps, that at 70 deg C the characteristics of the electrolyte are slightly inferior to those at 70 deg C, corresponding to an electrolyte degradation. Additionally, for the system studied, we found that the rate of variation of the potential difference in function of the temperature is quite high at the beginning of the operation process and tends to stabilize in a level of around 2,3-2,5 {mu}V per minute for times greater than 330 hours of operation. (author)

  10. Characterization of the inclusion complex ropivacaine: {beta}-cyclodextrin; Caracterizacao do complexo de inclusso ropivacaina: {beta}-ciclodextrina

    Energy Technology Data Exchange (ETDEWEB)

    Fraceto, Leonardo Fernandes [Universidade Estadual Paulista Julio de Mesquita Filho, Sorocaba, SP (Brazil). Dept. de Engenharia Ambiental]. E-mail: leonardo@sorocaba.unesp.br; Goncalves, Marcos Moises [Universidade de Sorocaba, SP (Brazil); Moraes, Carolina Morales; Araujo, Daniele Ribeiro de; Zanella, Luciana; Paula, Eneida de [Universidade Estadual de Campinas (UNICAMP), Campinas, SP (Brazil). Inst. de Biologia. Dept. de Bioquimica; Pertinhez, Thelma de Aguiar [Universidade de Parma (Italy). Dept. de Medicina Experimental

    2007-09-15

    Ropivacaine (RVC) is a widely used local anesthetic. The complexation of RVC with {beta}-cyclodextrin ({beta}-CD) is of great interest for the development of more efficient local anesthetic formulations. The present work focuses on the characterization of the RVC:{beta}-CD complex by nuclear magnetic resonance (NMR). The stoichiometry of the complex is 1:2 RVC:{beta}-CD. DOSY-NMR shows that the association constant is 55.5 M{sup -1}. Longitudinal relaxation time results show that RVC changes its mobility in the presence of {beta}-CD. This study is focused on the physicochemical characterization of inclusion complexes that are potentials options for pain treatment. (author)

  11. Preliminary characterization of dose in personnel of interventional radiology; Caracterizacao preliminar da dose em profissionais de radiologia intervencionista

    Energy Technology Data Exchange (ETDEWEB)

    Godolfim, Laura Larre; Anes, Mauricio; Bacelar, Alexandre; Lykawka, Rochelle [Hospital de Clinicas de Porto Alegre (HCPA), Porto Alegre, RS (Brazil)

    2016-07-01

    Exposure to X-rays of Interventional Radiology professionals (IR) impacts in the high dose rate received by these individuals, and there are reports of biological effects of this professional activity. Therefore, it is fomented greater control over the doses received by these workers. This research intends to characterize the doses received by the professionals during IR procedures. We evaluated the doses of radiologists, anesthesiologists and nursing staff of the Hospital de Clinicas de Porto Alegre, through measures with dosimeters of the OSL type, distributed in up to six regions of the body of these professionals. Until now were accompanied 33 cholangiography procedures and 29 embolization procedures. As a preliminary result, it was possible to identify a wide variation between doses of the professionals of the same function in each procedure. In overview, the dose of the professionals presented in descending order as a radiologist 1> radiologist 2 > anesthetist > nursing. (author)

  12. Silicon carbide hollow fiber membranes: obtainment and characterization; Membranas de fibra oca de carbeto de silicio: obtencao e caracterizacao

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, S.S.L.; Ferreira, R.S.B.; Araujo, B.A.; Medeiros, K.M.; Lucena, H.L.; Araujo, E.M., E-mail: sandriely_sonaly@hotmail.com [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Departamento de Engenharia de Materiais

    2016-07-01

    Silicon carbide is a promising material for the production of membranes due to its high melting temperature, thermal shock resistance, excellent mechanical and chemical stability. So, this study aims to characterize silicon carbide membranes in order to apply them in the separation of oil-water. A solution (SiC + PES + 1-Methyl- 2-Pyrrolidone) and through the extrusion technique by immersion precipitation membranes were obtained with hollow fiber geometry was prepared. And then sintered at 1500 ° C. For the characterization analyzes were made XRD, FTIR and SEM to evaluate the morphology and composition of the membranes obtained before and after sintering. (author)

  13. Synthesis and characterization of type silicoaluminophosphates catalytic support; Sintese e caracterizacao de suportes cataliticos do tipo silicoaluminofosfatico

    Energy Technology Data Exchange (ETDEWEB)

    Leite, C.E.T.; Carvalho, M.W.N.C.; Pereira, K.R.O., E-mail: carlosedisio@hotmail.co [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Unidade Academica de Engenharia Quimica. Lab. de Catalise, Adsorcao e Biocombustiveis

    2010-07-01

    The refining processes, the catalytic hydrocracking is the future of diesel oil in Brazil and the first units are already scheduled to be inaugurated. Among the catalysts used in this process, silicoaluminophosphates (SAPO's) have considerable potential for use as they have been effective in the isomerization of n-alkanes, the isomerization of olefins and alkylation of aromatics. Because of this, the objective is to develop catalysts that will be used in hydrocracking reactions. The media like SAPO-5 were synthesized with different ratios silicon/aluminum, which is used as a catalytic support and have the function of crack organic molecules, since it has acidic character. The materials were characterized by techniques: X-ray diffraction, chemical analysis and textural by BET. After summarizing the media found that they had agreements with the crystalline phases presented in the literature.(author)

  14. Structural characterization of clays commercially used in red ceramics; Caracterizacao estrutural de argilas de morros comercialmente utilizadas em ceramica vermelha

    Energy Technology Data Exchange (ETDEWEB)

    Brito, E.M.; Moura, J.K.L.; Souza, R.B.; Brandim, A.S., E-mail: ebrito.lbv@hotmail.com [Instituto Federal do Piaui(PPGEM/IFPI), Teresina, PI (Brazil)

    2014-07-01

    The use of clays hills being an alternative to clay floodplain, due to environmental protection laws. The research project aims at the morphological and chemical characterization of hills clays used industrially for the production of ceramic tiles and blocks. Therefore, two types of methods were known commercially in the region of Teresina-PI through diffraction of X-rays (X-DR), scanning electron microscopy (SEM) and energy dispersive spectrometry X-ray (EDS). It can be observed that the samples have a high percentage of quartz, hematite still having in its constitution aluminum oxide, zirconium oxide and titanium oxide. The results show that the clays are clays and montmorillonites may be used for the production of ceramic tiles and blocks, but as the proportion of using the same will be focusing the next job. (author)

  15. Viscosity and density study for characterization of oil mixtures; Estudo da viscosidade e densidade para caracterizacao das misturas de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Michelle I.; Azevedo, Vildomar S.; Jacinto, Tulio Wagner B. [Aurizonia Petroleo S.A, Natal, RN (Brazil); Vieira, Mariane; Vidal, Rosangela Regia Lima; Garcia, Rosangela Balaban [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)

    2008-07-01

    The oil can be defined as a mixture of hydrocarbons and sulphur, nitrogen and oxygenated organic derivatives at lower amount. There is a practical difficulty of analytical determination of the oil composition, mainly due to the large quantity of medium and heavy oil fractions. For heavier fractions, it is necessary to infer the composition of the cut from properties that can be readily obtained in the laboratory, such as refraction index, density and viscosity. The analysis of oil composition and its fractions is important information on various aspects (IOB et al., 1996): determining the operating conditions of refining, selection of suitable catalysts and mixing operations ('blending'), the economic evaluation of mixtures and analysis of environmental impact due to emissions. The first study on characterization of fractions of the oil was reported by Hill and Coats (1928), who set an empirical relationship between the density and Saybolt viscosity named viscosity-density constant (VGC). The statement was obtained from the analysis of the density with the oil viscosity changes. Physical properties such as density, boiling point and viscosity can be used to classify the oil. The aim of this work was to classify oil fractions based on viscosity-density constant, using mixtures of oils with different APIs. The results showed that there is an optimum composition for each mixture, and the addition of more oil of medium classification does not lead to potential commercial oil. (author)

  16. Clinical, radiographic and scintigraphic aspects of the trapeziometacarpal osteoarthritis; Caracterizacao clinica, radiografica e cintilografica da osteoartrose trapeziometacarpiana

    Energy Technology Data Exchange (ETDEWEB)

    Kaziyama, Helena Hideko Seguchi

    1996-12-31

    Trapeziometacarpal osteoarthritis occurs mainly in women during the menopausal period. It is related to manual activities and is usually bilateral. The onset is insidious and the evolution is slow and progressive. It is characterized by of strength and pain in the basis of the thumb resulting in limitation of the use and function of the hand. The diagnosis of this condition is based on the physical examination. The manouver of compression axial-rotation of the trapezimetacarpal joint is a common positive finding. Typical findings of osteoarthritis are present in the radiological studies. Scintigraphic images have a predictive value. The early diagnosis is important to avoid the risk factors and to prevent disabilities of the hand. (author) 102 refs., 18 figs., 10 tabs.

  17. Hydrodynamic characterization in areas under influence in the petroleum industry; Caracterizacao hidrodinamica em areas sob influencia na industria petrolifera

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Daniel Alexsander Silva dos; Silva, Andre Giskard Aquino da [Rio Grande do Norte Univ., Natal, RN (Brazil)]. E-mail: danielsandersilva@hotmail.com; Vital, Helenice [Conselho Nacional de Desenvolvimento Cientifico e Tecnologico (CNPq), Brasilia, DF (Brazil); Silveira, Iracema Miranda da [Museu Camara Cascudo, Natal, RN (Brazil); Chaves, Marcelo dos Santos; Lima, Zuleide Maria Carvalho [Rio Grande do Norte Univ., Natal, RN (Brazil). Programa de Pos-graduacao em Geodinamica e Geofisica

    2003-07-01

    For elaboration of contingency plans it is necessary to execute the mapping of sensitive areas to oil spill, as well as to create suitable forecast models for oil pollution movements. These models should start from a consistent database, so that it can encompass the several phases of the environmental monitoring. In both cases hydrodynamic data are essential. The analysis of hydrodynamic parameters is also an important phase for the knowledge of the Holocene evolution of the study area, as well as for execution of a suitable development policy to be applied on the area. The activities developed in this research involve collection of data 'in situ' at the Galinhos-Guamare and Diogo Lopes lagoons, as well as data manipulation referring to the littoral drift collected monthly along the North coast of the state of Rio Grande do Norte by members of the Grupo de Geologia e Geofisica Marinha e Melhoramento Ambiental (GGEMMA) from UFRN.

  18. Extraction and characterization of crude oil asphaltenes sub fractions; Extracao e caracterizacao de subfracoes de asfaltenos de petroleo

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira, Silas R.; Calado, Lucas S.; Honse, Siller O.; Mansur, Claudia R.E.; Lucas, Elizabete F., E-mail: silas@ima.ufrj.br [Universidade Federal do Rio de Janeiro, Instituto de Macromoleculas, Laboratorio de Macromoleculas e Coloides na Industria de Petroleo, Rio de Janeiro, RJ (Brazil)

    2011-07-01

    Asphaltenes from crude oil have been studied for a long time. However, until today their chemical structures and physical-chemical properties are not well established. Nowadays, it is accepted that asphaltenes are dispersed in the crude oil as macro structures, which are mainly constituted of some condensed aromatic rings (about 6-20), containing aliphatic or naphthenic groups. The asphaltenes are also defined as the crude oil fraction that is insoluble in low molar mass n-alkanes and soluble in aromatic solvents, like benzene and toluene In order to investigate the molecular structure, in this work the asphaltenes were separated by using a different procedure as that normally described in the literature and characterized by infrared spectrometry, nuclear magnetic resonance, x-ray fluorescence, elemental analyses and particle size and size distribution. The difference in subfractions polarity can be attributed not only to the aromaticity changes but also to the content of elements, such as N, O, Fe, V, Si e Ni. (author)

  19. Poly(vinylpyrrolidone)/silver nanoparticles: preparation and characterization; Nanoparticulas de prata/poli(vinilpirrolidona): obtencao e caracterizacao

    Energy Technology Data Exchange (ETDEWEB)

    Andrade, P.F.; Goncalves, M.C. [Instituto de Quimica - UNICAMP, Campinas, SP (Brazil)], e-mail: patandrade@iqm.unicamp.br

    2010-07-01

    In this work silver nanoparticles were prepared by chemical reduction method using PVP as dispersant agent. The formation of silver nanoparticles was investigated by UV-vis optical spectroscopy and X-ray diffraction. FT-IR spectroscopy confirmed the formation of Ag/PVP complex. The transmission electron microscopy images indicated that the concentration of Ag{sup +} precursor influenced the nanoparticles dispersion and size distribution significantly. The results indicated that dispersed nanoparticles with uniform size distribution can be prepared by this methodology to obtain polymeric nano composites. (author)

  20. Synthesis and characterization of polyanhydride derived from castor oil; Sintese e caracterizacao de polianidrido derivado do oleo de mamona

    Energy Technology Data Exchange (ETDEWEB)

    Borges, Fernando de M.; Reis, Roberta Yonara Nascimento; Nobre, Francisco X.; Matos, Jose M.E., E-mail: robertayonara@gmail.com [Universidade Federal do Piaui (UFPI), Teresina, PI (Brazil)

    2015-07-01

    Polyanhydrides are biopolymers already used as drug carriers, that allow the controlled release of the drug in vivo. Currently, these polymers are produced from a polyol, such as ethyleneglycol. In this work we synthesized a polyanhydride from castor oil, from the derivatization of oil via alcoholysis reaction. The oil was then converted to a monoglyceride (MG) by alcoholysis reaction at 140 °C. The MG reacted with phthalic anhydride (PA) at 100 °C, forming the polymer P1. The polymer was characterized by FT-IR, {sup 1}H and {sup 13}C NMR. These techniques allowed confirmation of the polymer formation. (author)

  1. Characterization of poly pyrrole/montmorillonite electro polymerised onto Pt; Caracterizacao de filmes PPy/montmorilonita eletropolimerizados sobre Pt

    Energy Technology Data Exchange (ETDEWEB)

    Castagno, K.R.L., E-mail: katiarlc@pelotas.ifsul.edu.b [Instituto Federal Sul-rio-grandense (IFSul), RS (Brazil). Dept. de Quimica; Azambuja, D.S.; Dalmoro, V.; Mauller, R.S. [Universidade Federal do Rio Grande do Sul (UFRGS), Pelotas, RS (Brazil). Inst. de Quimica

    2010-07-01

    In this study films of polypyrrole/montmorillonite (PPy/MT) were electropolymerized on platinum in order to evaluate the performance of this technique in the preparation of nanocomposite materials and to determine the thermal properties and conductivity of the composites. The films were synthesized from a solution containing pyrrole, dodecylbenzene sulfonate, acid and two types of clays: montmorillonite-Na + (MT-Na) and montmorillonite-30B (MT-M). The characterization of the films we have used FT-IR, TEM, XRD, TGA, DSC and resistivity measurement by the four-point van der Pauw method. The study showed that the adopted method of exfoliation and the electropolymerization method used, allows obtaining nanocomposite materials. Analyses of FT-IR, TEM and XRD show that the clays are exfoliated in the polymer matrix. Thermal analysis of the films indicates that the addition of clay reflects an enhancement in the thermal properties of the matrix of PPy, but decreases the conductivity of the same. (author)

  2. Characterization of film-converter screens systems for neutron radiography; Caracterizacao de sistemas filme-conversor para radiografia com neutrons

    Energy Technology Data Exchange (ETDEWEB)

    Andrade, Marcos Leandro Garcia

    2002-07-01

    In general a good quality radiography is that one able to furnish high contrast and sharp edge images. Technically 'high contrast' means high capability to discern material thickness and 'sharp edges', high resolution power. In the present work the optimal conditions to obtain neutron radiography images by using the following film-converter screen systems, Kodak-AA/Gd vaporated; Kodak-AA/Gd metallic; Kodak-AA/LiF; Min-R/GdS{sub 2}O{sub 4}, have been determined. The irradiations were performed in a radiographic facility which was designed and constructed by the neutron radiography working group and is installed at the beamhole 08 of the IEA-R1 nuclear research reactor of the IPEN-CNEN/SP. In order to determine such conditions, the start point was to evaluate the neutron exposure interval for which the optical contrast is maximal and so quantify the sensitivity or capability to discern material thickness, as well as the spatial resolution achieved in the radiographic image, for these systems. The best results have been obtained for the Kodak-AA/Gd vaporated system which is able to discern, for example, 0,024 cm of lucite, with a maximal resolution of 22{mu}m. The radiography images presently obtained in IPEN-CNEN/SP have similar quality when compared to the ones from several other research centers, around the world, whose making use of the same film-converter screens systems. (author)

  3. Chemistry characterization and samples beryllium process impurity determination; Caracterizacao quimica e determinacao de impurezas de amostras de processo de berilio

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, Leonel Mathry de

    1992-12-01

    Brazil is the greatest world producer of beryl (3 Be O.Al{sub 2}O{sub 3}.6SiO{sub 2}) and has recently begun to produce beryllium compounds by means of a pilot plant constructed at Governador Valadares city (Minas Gerais - Brazil). The aim of this work was the determination of trace level impurities and macro constituents in the tenth % range to support analytical control process of plant production and characterization of beryllium compounds. The impurities separations and purification process was developed by two steps procedure. The first one using EDTA complexation has separated and reduced some impurities to less than 1 {mu}g/ml level. In the second one it was used a chelating resin (Chelex 100) and the separation efficiency was about 75 to 97 % related with the element tested. High pure berylium oxide standard was obtained from purification of Be(OH)2. The R X fluorescence presented only traces of Cu and Si < 1 % Fe and Mn, Zn, Ca, Al, Na and S were completely removed. The beryllium content was determined by direct atomic emission spectroscopy in argon plasma (Dcp) and compared with classic gravimetric method as Be O. The results were in agreement (49,2+/-0,2 % and 48,3+/-0,1 % respectively) between 95 % of confidence. A low temperature gravimetric method for beryllium determination was also studied using Oxine with microwave furnace. A total of 24 elements including macro and trace level were determined by Dcp and/or spectrophotometric methods. The Be/B separation was studied using anionic resin in poly alcohols medium. A more detailed study of equilibrium conditions is necessary. This work was realized at Laboratorio de Analise Mineral (LAM) of Comissao Nacional de Energia Nuclear - Rio de Janeiro (CNEN). (author)

  4. Characterization of ionizing radiation effects on human skin allografts; Caracterizacao dos efeitos da radiacao ionizante em pele humana para aloenxerto

    Energy Technology Data Exchange (ETDEWEB)

    Bourroul, Selma Cecilia

    2004-07-01

    The skin has a fundamental role in the viability of the human body. In the cases of extensive wounds, allograft skin provides an alternative to cover temporarily the damaged areas. After donor screening and preservation in glycerol (above 85%), the skin can be stored in the Skin Banks. The glycerol at this concentration has a bacteriostatic effect after certain time of preservation. On the other hand, skin sterilization by ionizing radiation may reduces the quarantine period for transplantation in patients and its safety is considered excellent. The objectives of this work were to establish procedures using two sources of ionizing radiation for sterilization of human skin allograft, and to evaluate the skin after gamma and electron beam irradiation. The analysis of stress-strain intended to verify possible effects of the radiation on the structure of preserved grafts. Skin samples were submitted to doses of 25 kGy and 50 kGy in an irradiator of {sup 60}Co and in an electron beam accelerator. Morphology and ultra-structure studies were also accomplished. The samples irradiated with a dose of 25 kGy seemed to maintain the bio mechanic characteristics. The gamma irradiated samples with a dose of 50 kGy and submitted to an electron beam at doses of 25 kGy and 50 kGy presented significant differences in the values of the elasticity modulus, in relation to the control. The analysis of the ultramicrographies revealed modifications in the structure and alterations in the pattern of collagen fibrils periodicity of the irradiated samples. (author)

  5. Characterization of AA7050 aluminium alloy processed by ECAP; Caracterizacao da liga de aluminio AA7050 processada por ECAP

    Energy Technology Data Exchange (ETDEWEB)

    Cardoso, K.R.; Guido, V. [Universidade do Vale do Paraiba (UNIVAP), Sao Jose dos Campos, SP (Brazil). Inst. de Pesquisa e Desenvolvimento; Travessa, D.N. [Empresa Brasileira de Aeronautica (EMBRAER), Sao Jose dos Campos, SP (Brazil); Jorge Junior, A.M. [Universidade Federal de Sao Carlos (DEMa/UFSCar), SP (Brazil). Dept. de Engenharia de Materiais

    2010-07-01

    The commercial AA7050 aluminium alloy in the solution heat treated condition (W) was processed by ECAP through route A. Two pressing temperatures (room and 150 deg C and velocities (5 and 30mm/min) were used, as well as different number of passes. The effect of such variables on the microstructure evolution was evaluated using optical and transmission electron microscopy with EDX microanalysis, and xray diffraction. It was found that the microstructure has been refined by ECAP, as a result of subgrains formed within deformation bands. ECAP at 150 deg C resulted in intense precipitation of plate like {eta} phase, which evolves to equiaxial morphology as the number of passes increases. (author)

  6. Study and characterization of porous ceramic obtained via gelatinization; Estudo e caracterizacao de corpos ceramicos porosos obtidos via gelatinizacao

    Energy Technology Data Exchange (ETDEWEB)

    Storion, A.G.; Campos, M.G.N.; Mariano, N.A.; Maestrelli, S.C. [Universidade Federal de Alfenas (UNIFAL), Pocos de Caldas, MG (Brazil); Mariano, W.A., E-mail: gabiags@hotmail.com [Universidade Federal de Sao Carlos(UFSCar), SP (Brazil)

    2016-07-01

    Conventional processes for manufacturing porous ceramic sometimes provide bodies with low mechanical strength, showing cracks and macro defects, in addition to the high complexity or cost. This work proposes a new porous ceramic processing route called cold gelatinization, using as raw material a clay with low plasticity, water and gelatin. At first, the characterization of the clay was carried out and then specimens of various compositions were produced by varying clay content (40, 50, 55 and 60% of solids) and keeping the water and gelatin content constant in the formulation. After cold forming the samples were and fired under various conditions: initial temperature of 300 or 600 °C; maximum firing temperature of 800, 900, 1000, 1100 or 1350 °C. After firing, it was obtained water absorption, apparent density, apparent porosity, linear shrinkage and mechanical resistance via 3 points bending test. The best results were for samples fired in temperatures lower than 1100 °C and 50% and 55 % of solid content. (author)

  7. Concrete hardened characterization using table scanner and microtomography computed; Caracterizacao de concreto endurecido utilizando scaner de mesa e microtomografia computadorizada

    Energy Technology Data Exchange (ETDEWEB)

    Wilson, R.E.; Pessoa, J.R.; Assis, J.T. de, E-mail: jrenatopessoa@gmail.com [Universidade do Estado do Rio de Janeiro (IPRJ/UERJ), RJ (Brazil); Dominguez, D.S.; Dias, L.A.; Santana, M. R. [Universidade Estadual de Santa Cruz (UESC), Ilheus, BA (Brazil)

    2016-07-01

    This paper proposes the use of image processing technologies to analyze hardened concrete samples obtained from table scanner and micro tomography. Techniques will be used to obtain numerical data on the distribution and geometry of aggregates and pores of the concrete, as well as their relative position. It is expected that the data obtained can produce information on the research of concrete pathologies such as AAR, and the freeze / thaw process. (author)

  8. Synthesis and characterization of metal soaps of lanthanides (III); Sintese e caracterizacao de saboes metalicos de lantanidios (III)

    Energy Technology Data Exchange (ETDEWEB)

    Payolla, Filipe Boccato; Ribeiro, Sidney Jose Lima; Massbni, Antonio Carlos [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Araraquara, SP (Brazil). Instituto de Quimica; Centro Universitario de Araraquara (UNIARA), Araraquara, SP (Brazil)

    2015-07-01

    The present study describes synthesis and partial characterization of Eu{sup 3+}, Nd{sup 3+}, Dy{sup 3+}, Tb{sup 3+} and Yb{sup 3+} behenate complexes. The compounds were analyzed using IR-Spectroscopy, TG-DTG, DSC, elemental analysis, XRD, luminescence and SEM. The results show the purity of the compounds. The XRD analysis and the SEM images show the high crystallinity of the complexes. TG-DTG and DSC analyses do not show a liquid crystal behavior, as occurs with other lanthanide metallic soaps. The mass loses until 1000° C show that the compounds lose ligand fragments at specific temperatures. XRD of the residues are compatible with the respective lanthanide oxides. The luminescence analysis shows that the Eu{sup 3+}, Nd{sup 3+} and Tb{sup 3+} complexes presents appreciable emission. The Judd-Ofelt parameters obtained are compatible with the values found in the literature. It was not possible to obtain the complexes in a glass-form because it is difficult to prevent the crystallization of the complexes even using liquid nitrogen. The XDR data indicate that one of the complexes axis has 52 Å of length, agreeing with a structure containing behenate-lanthanide ion-behenate. The structures of the complexes were not fully elucidated and more analyses are necessary. The complexes presented a molar ratio of 3:1 (L:M) and were formulated as Bh{sub 3}Eu, Bh{sub 3}Nd, Bh{sub 3}Dy, Bh{sub 3}Tb e Bh{sub 3}Yb (Bh = behenate anion). (author)

  9. Commissioning of Portal Dosimetry and characterization of an EPID; Comissionamento de Portal Dosimetry e caracterizacao de EPID

    Energy Technology Data Exchange (ETDEWEB)

    Olbi, D.S.; Sales, C.P. [Universidade de Sao Paulo (USP), SP (Brazil). Faculdade de Medicina; Nakandakari, M.V.N., E-mail: diego.olbi@hc.fm.usp.br [Instituto do Cancer do Estado de Sao Paulo, SP (Brazil). Servico de Radioterapia

    2016-07-01

    The development of technologies compensator blocks, MLC, high dose rate accelerators, treatment planning systems, among others, permitted that new treatment techniques in radiotherapy were created. Such techniques have the capacity to modulate radiation beam fluency (IMRT, VMAT), or to deliver high doses in few fractions or unique fractions (SRS). Following the same tendency, quality control of planning became more complex. It is necessary to evaluate the fluency delivered by the accelerator. Its levels of does and its spatial distribution should co-occur with the fluency calculated by TPS. Acquisition of new detector devices in quality control of treatments is fundamental to apply techniques. Portal Vision is a device EPID has the capacity to operate either in image mode or dosimetry mode, with the allowance of Portal Dosimetry. To evaluated planning in IMRT, the device is irradiated using planning e, therefore, the fluency measured is compared with calculated fluency, through gamma analysis. The aim of this work was to perform tests of commissioning of this device. (author)

  10. Electrochemical characterization of calcium cobaltite based porous electrodes; Caracterizacao eletroquimica de eletrodos porosos a base de cobaltita de calcio

    Energy Technology Data Exchange (ETDEWEB)

    Fulgencio, E.B.G.A.; Vasconcelos, K.; Silva, R.M.; Melo, P.; Caetano, A.A.; Campos, L.F.A.; Dutra, R.P.S.; Macedo, D.A., E-mail: erikbgrisi@gmail.com [Universidade Federal da Paraiba (UFPB), PB (Brazil)

    2016-07-01

    Materials based on alkali metal oxides and alkaline earth metal have shown high technological interest in recent years. Among these materials, calcium and cobalt oxide composition Ca{sub 3}Co{sub 4}O{sub 9} (C349) has emerged as thermoelectric material and, more recently, as cathode for solid oxide fuel cell (SOFC). In this study, C349 powder was obtained by solid state reaction of a mixture containing cobalt oxide and calcium carbonate from shellfish shells (CaCO{sub 3} ∼ 98%), previously calcined at 550° C. Symmetrical cells (cathode / substrate / cathode) were prepared by screen printing of C349 electrodes in gadolinium-doped ceria substrates. The characterization by electrochemical impedance spectroscopy revealed that the C349 obtained in this work has an area specific resistance compatible with electrodes obtained by chemical routes (from literature). (author)

  11. Characterization of marble waste for manufacture of artificial stone; Caracterizacao de residuo de marmore para fabricacao de rocha artificial

    Energy Technology Data Exchange (ETDEWEB)

    Aguiar, M.C.; Silva, A.G.P., E-mail: maricostalonga2@gmail.com [Universidade Estadual do Norte Fluminense (UENF/LAMAV), Campos dos Goytacazes, RJ (Brazil). Laboratorio de Materiais Avancados; Gadioli, M.C.B. [Centro de Tecnologia Mineral (CETEM/NR-ES), Cachoeiro de Itapemirim, ES (Brazil)

    2016-07-01

    This work aims to study the characterization of marble waste for the manufacture of artificial stone. The characterization of the waste was performed through X-ray fluorescence, X-ray diffraction, particle size distribution, scanning electron microscopy and confocal microscopy. The results indicated that the marble waste presents typical composition of a dolomite, calcite marble, and their minerals are: Calcite (CaCO{sub 3}) and dolomite (MgCa (CO{sub 3}){sub 2}. The waste presented predominance of particles below 200 mesh screen. This may be interesting for the production of artificial stone better visual appearance, such as marmoglass, for example. The results indicate that the use of marble waste for production of artificial stone is feasible and environmentally friendly alternative to give a destination for this waste generated in the order of millions of tons representing serious environmental problem. (author)

  12. Synthesis, characterization and thermal behavior of rare earth amido sulfonates; Sintese, caracterizacao e comportamento termico de amidossulfonatos de terras raras

    Energy Technology Data Exchange (ETDEWEB)

    Luiz, Jose Marques; Nunes, Ronaldo Spezia, E-mail: jmluiz@feg.unesp.br [Universidade Estadual Paulista Julio Mesquita Filho (UNESP), Guaratingueta, SP (Brazil). Faculdade de Engenharia. Departamento de Fisica e Quimica; Matos, Jivaldo do Rosario [Universidade de Sao Paulo (USP), SP (Brazil). Instituto de Quimica

    2013-09-01

    Hydrated compounds prepared in aqueous solution by reaction between amidosulfonic acid [H{sub 3}NSO{sub 3}] and suspensions of rare earth hydroxycarbonates [Ln{sub 2}(OH){sub x}(CO{sub 3}){sub y}.zH{sub 2}O] were characterized by elemental analysis (% Ln, % N and % H), infrared spectroscopy (FTIR) and thermogravimetry (TG). The compounds presented the stoichiometry Ln(NH{sub 2}SO{sub 3}){sub 3}.xH{sub 2}O (where x = 1, 5, 2.0 or 3.0). The IR spectra showed absorptions characteristic of H{sub 2}O molecules and NH{sub 2}SO{sub 3} groups. Degree of hydration, thermal decomposition steps and formation of stable intermediates of the type [Ln{sub 2}(SO{sub 4}){sub 3}] and (Ln{sub 2}O{sub 2}SO{sub 4}), besides formation of their oxides, was determined by thermogravimetry. (author)

  13. Clean Energy Application Center

    Energy Technology Data Exchange (ETDEWEB)

    Freihaut, Jim [Pennsylvania State Univ., University Park, PA (United States)

    2013-09-30

    The Mid Atlantic Clean Energy Application Center (MACEAC), managed by The Penn State College of Engineering, serves the six states in the Mid-Atlantic region (Pennsylvania, New Jersey, Delaware, Maryland, Virginia and West Virginia) plus the District of Columbia. The goals of the Mid-Atlantic CEAC are to promote the adoption of Combined Heat and Power (CHP), Waste Heat Recovery (WHR) and District Energy Systems (DES) in the Mid Atlantic area through education and technical support to more than 1,200 regional industry and government representatives in the region. The successful promotion of these technologies by the MACEAC was accomplished through the following efforts; (1)The MACEAC developed a series of technology transfer networks with State energy and environmental offices, Association of Energy Engineers local chapters, local community development organizations, utilities and, Penn State Department of Architectural Engineering alumni and their firms to effectively educate local practitioners about the energy utilization, environmental and economic advantages of CHP, WHR and DES; (2) Completed assessments of the regional technical and market potential for CHP, WHR and DE technologies application in the context of state specific energy prices, state energy and efficiency portfolio development. The studies were completed for Pennsylvania, New Jersey and Maryland and included a set of incentive adoption probability models used as a to guide during implementation discussions with State energy policy makers; (3) Using the technical and market assessments and adoption incentive models, the Mid Atlantic CEAC developed regional strategic action plans for the promotion of CHP Application technology for Pennsylvania, New Jersey and Maryland; (4) The CHP market assessment and incentive adoption model information was discussed, on a continuing basis, with relevant state agencies, policy makers and Public Utility Commission organizations resulting in CHP favorable incentive

  14. Security in Computer Applications

    CERN Multimedia

    CERN. Geneva

    2004-01-01

    Computer security has been an increasing concern for IT professionals for a number of years, yet despite all the efforts, computer systems and networks remain highly vulnerable to attacks of different kinds. Design flaws and security bugs in the underlying software are among the main reasons for this. This lecture addresses the following question: how to create secure software? The lecture starts with a definition of computer security and an explanation of why it is so difficult to achieve. It then introduces the main security principles (like least-privilege, or defense-in-depth) and discusses security in different phases of the software development cycle. The emphasis is put on the implementation part: most common pitfalls and security bugs are listed, followed by advice on best practice for security development. The last part of the lecture covers some miscellaneous issues like the use of cryptography, rules for networking applications, and social engineering threats. This lecture was first given on Thursd...

  15. Laser applications in neurosurgery

    Science.gov (United States)

    Cerullo, Leonard J.

    1985-09-01

    The "false start" of the laser in neurosurgery should not be misconstrued as a denial of the inherent advantages of precision and gentleness in dealing with neural tissue. Rather, early investigators were frustrated by unrealistic expectations, cumbersome equipment, and a general ignorance of microtechnique. By the early 70s, microneurosurgery was well established, surgical laser equipment for free hand and microlinked application had been developed, and a more realistic view of the limitations of the laser had been established. Consequently, the late 70s really heralded the renaissance of the laser in neurosurgery. Since then, there has been an overwhelming acceptance of the tool in a variety of clinical situations, broadly categorized in five groups. 1)|Perhaps the most generally accepted area is in the removal of extra-axial tumors of the brain and spinal cord. These tumors, benign by histology but treacherous by location, do not present until a significant amount of neurological compensation has already occurred. The application of additional trauma to the neural tissue, whether by further tumor growth or surgical manipulation, frequently results in irreversible damage. Here, the ability of the laser to vaporize tissue, in a fairly hemostatic fashion, without mechanical or thermal damage to sensitive surrounding tissues, is essential. 2)|The ability to incise delicate neural tissue with minimal spread of thermal destruction to adjacent functioning tissue makes the laser the ideal instrument when tumors deep under the surface are encountered in the brain or spinal cord. Thus, the second group of applications is in the transgression of normal neural structures to arrive at deeper pathological tissue. 3)|The third area of benefit for the laser in neurosurgery has been in the performance of neuroablative procedures, calling for deliberate destruction of functioning neural tissue in a controlled fashion. Again, the precision and shape confinement of the destructive

  16. Tensors and their applications

    CERN Document Server

    Islam, Nazrul

    2006-01-01

    About the Book: The book is written is in easy-to-read style with corresponding examples. The main aim of this book is to precisely explain the fundamentals of Tensors and their applications to Mechanics, Elasticity, Theory of Relativity, Electromagnetic, Riemannian Geometry and many other disciplines of science and engineering, in a lucid manner. The text has been explained section wise, every concept has been narrated in the form of definition, examples and questions related to the concept taught. The overall package of the book is highly useful and interesting for the people associated with the field. Contents: Preliminaries Tensor Algebra Metric Tensor and Riemannian Metric Christoffel`s Symbols and Covariant Differentiation Riemann-Christoffel Tensor The e-Systems and the Generalized Krönecker Deltas Geometry Analytical Mechanics Curvature of a Curve, Geodesic Parallelism of Vectors Ricci`s Coefficients of Rotation and Congruence Hyper Surfaces

  17. Interpretation and clinical applications

    International Nuclear Information System (INIS)

    Higgins, C.B.

    1987-01-01

    This chapter discusses the factors to be kept in mind during routine interpretation of MR images. This includes the factors that determine contrast on standard spin-echo images and some distinguishing features between true lesions and artifactually simulated lesions. This chapter also indicates the standard protocols for MRI of various portions of the body. Finally, the current indications for MRI of various portions of the body are suggested; however, it is recognized that the indications for MRI are rapidly increasing and consequently, at the time of publication of this chapter, it is likely that many more applications will have become evident. Interpretation of magnetic resonance (MR) images requires consideration of anatomy and tissue characteristics and extraction of artifacts resulting from motion and other factors

  18. Bilevel Programming and Applications

    Directory of Open Access Journals (Sweden)

    Vyacheslav V. Kalashnikov

    2015-01-01

    Full Text Available A great amount of new applied problems in the area of energy networks has recently arisen that can be efficiently solved only as mixed-integer bilevel programs. Among them are the natural gas cash-out problem, the deregulated electricity market equilibrium problem, biofuel problems, a problem of designing coupled energy carrier networks, and so forth, if we mention only part of such applications. Bilevel models to describe migration processes are also in the list of the most popular new themes of bilevel programming, as well as allocation, information protection, and cybersecurity problems. This survey provides a comprehensive review of some of the above-mentioned new areas including both theoretical and applied results.

  19. Phase transitions modern applications

    CERN Document Server

    Gitterman, Moshe

    2014-01-01

    This book provides a comprehensive review of the theory of phase transitions and its modern applications, based on the five pillars of the modern theory of phase transitions i.e. the Ising model, mean field, scaling, renormalization group and universality. This expanded second edition includes, along with a description of vortices and high temperature superconductivity, a discussion of phase transitions in chemical reaction and moving systems. The book covers a close connection between phase transitions and small world phenomena as well as scale-free systems such as the stock market and the Internet. Readership: Scientists working in different fields of physics, chemistry, biology and economics as well as teaching material for undergraduate and graduate courses.

  20. Stochastic calculus and applications

    CERN Document Server

    Cohen, Samuel N

    2015-01-01

    Completely revised and greatly expanded, the new edition of this text takes readers who have been exposed to only basic courses in analysis through the modern general theory of random processes and stochastic integrals as used by systems theorists, electronic engineers and, more recently, those working in quantitative and mathematical finance. Building upon the original release of this title, this text will be of great interest to research mathematicians and graduate students working in those fields, as well as quants in the finance industry. New features of this edition include: End of chapter exercises; New chapters on basic measure theory and Backward SDEs; Reworked proofs, examples and explanatory material; Increased focus on motivating the mathematics; Extensive topical index. "Such a self-contained and complete exposition of stochastic calculus and applications fills an existing gap in the literature. The book can be recommended for first-year graduate studies. It will be useful for all who intend to wo...