WorldWideScience

Sample records for application psar volume

  1. Nuclear Fuel Recovery and Recycling Center. License application, PSAR, volume 3

    International Nuclear Information System (INIS)

    Volume 3 comprises Chapter 5 which provides descriptive information on Nuclear Fuel Recovery and Recycling Center buildings and other facilities, including their locations. The design features discussed include those used to withstand environmental and accidental forces and to insure radiological protection

  2. Marble Hill Nuclear Generating Station, Units 1 and 2. License application, PSAR, general information

    International Nuclear Information System (INIS)

    An application is presented for two PWR reactors to be constructed in Salud Township, Jefferson County, Indiana, about six miles northeast of New Washington on the Ohio River. Each unit will have a rated core power level of 3411 MW(t) with a corresponding electrical output of 1130 MW(e). Mechanical draft cooling towers will be provided. The facility, which will replicate the Byron facility will be employed for the generation of electricity for transmission, sale for resale, and distribution

  3. Preliminary Safety Analysis Report (PSAR), The NSLS 200 MeV Linear Electron Accelerator

    Energy Technology Data Exchange (ETDEWEB)

    Blumberg, L.N.; Ackerman, A.I.; Dickinson, T.; Heese, R.N.; Larson, R.A.; Neuls, C.W.; Pjerov, S.; Sheehan, J.F.

    1993-06-15

    The radiological, fire and electrical hazards posed by a 200 MeV electron Linear Accelerator, which the NSLS Department will install and commission within a newly assembled structure, are addressed in this Preliminary Safety Analysis Report. Although it is clear that this accelerator is intended to be the injector for a future experimental facility, we address only the Linac in the present PSAR since neither the final design nor the operating characteristics of the experimental facility are known at the present time. The fire detection and control system to be installed in the building is judged to be completely adequate in terms of the marginal hazard presented - no combustible materials other than the usual cabling associated with such a facility have been identified. Likewise, electrical hazards associated with power supplies for the beam transport magnets and accelerator components such as the accelerator klystrons and electron gun are classified as marginal in terms of potential personnel injury, cost of equipment lost, program downtime and public impact perceptions as defined in the BNL Environmental Safety and Health Manual and the probability of occurrence is deemed to be remote. No unusual features have been identified for the power supplies or electrical distribution system, and normal and customary electrical safety standards as practiced throughout the NSLS complex and the Laboratory are specified in this report. The radiation safety hazards are similarly judged to be marginal in terms of probability of occurrence and potential injury consequences since, for the low intensity operation proposed - a factor of 25 less than the maximum Linac capability specified by the vendor - the average beam power is only 0.4 watts. The shielding specifications given in this report will give adequate protection to both the general public and nonradiation workers in areas adjacent to the building as well as radiation workers within the controlled access building.

  4. P-SAR: An Advanced Miniature Synthetic Aperture Radar for Forestry Applications. Preliminary Design

    NARCIS (Netherlands)

    Figueras i Ventura, J.; Hoogeboom, P.

    2005-01-01

    A preliminary study of the design of a small, low cost, Pband airborne, polarimetric synthetic aperture radar (SAR) is presented. The design was requested by the Wageningen University and the Borneo Orangutan Survival Foundation (BOS) to carry out forest biomass monitoring in Indonesia. The requirem

  5. Partial scan artifact reduction (PSAR) for the assessment of cardiac perfusion in dynamic phase-correlated CT

    Energy Technology Data Exchange (ETDEWEB)

    Stenner, Philip; Schmidt, Bernhard; Bruder, Herbert; Allmendinger, Thomas; Haberland, Ulrike; Flohr, Thomas; Kachelriess, Marc [Institute of Medical Physics, Henkestrasse 91, 91052 Erlangen (Germany); Siemens AG, Healthcare Sector, Siemensstrasse 1, 91301 Forchheim (Germany); Institute of Medical Physics, Henkestrasse. 91, 91052 Erlangen (Germany)

    2009-12-15

    Purpose: Cardiac CT achieves its high temporal resolution by lowering the scan range from 2{pi} to {pi} plus fan angle (partial scan). This, however, introduces CT-value variations, depending on the angular position of the {pi} range. These partial scan artifacts are of the order of a few HU and prevent the quantitative evaluation of perfusion measurements. The authors present the new algorithm partial scan artifact reduction (PSAR) that corrects a dynamic phase-correlated scan without a priori information. Methods: In general, a full scan does not suffer from partial scan artifacts since all projections in [0, 2{pi}] contribute to the data. To maintain the optimum temporal resolution and the phase correlation, PSAR creates an artificial full scan p{sub n}{sup AF} by projectionwise averaging a set of neighboring partial scans p{sub n}{sup P} from the same perfusion examination (typically N{approx_equal}30 phase-correlated partial scans distributed over 20 s and n=1,...,N). Corresponding to the angular range of each partial scan, the authors extract virtual partial scans p{sub n}{sup V} from the artificial full scan p{sub n}{sup AF}. A standard reconstruction yields the corresponding images f{sub n}{sup P}, f{sub n}{sup AF}, and f{sub n}{sup V}. Subtracting the virtual partial scan image f{sub n}{sup V} from the artificial full scan image f{sub n}{sup AF} yields an artifact image that can be used to correct the original partial scan image: f{sub n}{sup C}=f{sub n}{sup P}-f{sub n}{sup V}+f{sub n}{sup AF}, where f{sub n}{sup C} is the corrected image. Results: The authors evaluated the effects of scattered radiation on the partial scan artifacts using simulated and measured water phantoms and found a strong correlation. The PSAR algorithm has been validated with a simulated semianthropomorphic heart phantom and with measurements of a dynamic biological perfusion phantom. For the stationary phantoms, real full scans have been performed to provide theoretical reference

  6. Finite Volumes for Complex Applications VII

    CERN Document Server

    Ohlberger, Mario; Rohde, Christian

    2014-01-01

    The methods considered in the 7th conference on "Finite Volumes for Complex Applications" (Berlin, June 2014) have properties which offer distinct advantages for a number of applications. The second volume of the proceedings covers reviewed contributions reporting successful applications in the fields of fluid dynamics, magnetohydrodynamics, structural analysis, nuclear physics, semiconductor theory and other topics. The finite volume method in its various forms is a space discretization technique for partial differential equations based on the fundamental physical principle of conservation. Recent decades have brought significant success in the theoretical understanding of the method. Many finite volume methods preserve further qualitative or asymptotic properties, including maximum principles, dissipativity, monotone decay of free energy, and asymptotic stability. Due to these properties, finite volume methods belong to the wider class of compatible discretization methods, which preserve qualitative propert...

  7. Electrical Capacitance Volume Tomography: Design and Applications

    OpenAIRE

    Warsito Warsito; Liang-Shih Fan; Qussai Marashdeh; Fei Wang

    2010-01-01

    This article reports recent advances and progress in the field of electrical capacitance volume tomography (ECVT). ECVT, developed from the two-dimensional electrical capacitance tomography (ECT), is a promising non-intrusive imaging technology that can provide real-time three-dimensional images of the sensing domain. Images are reconstructed from capacitance measurements acquired by electrodes placed on the outside boundary of the testing vessel. In this article, a review of progress on capa...

  8. 6th international symposium on finite volumes for complex applications

    CERN Document Server

    Halama, Jan; Herbin, Raphaèle; Hubert, Florence; Fort, Jaroslav; FVCA 6; Finite Volumes for Complex Applications VI : Problems and perspectives

    2011-01-01

    Finite volume methods are used for various applications in fluid dynamics, magnetohydrodynamics, structural analysis or nuclear physics. A closer look reveals many interesting phenomena and mathematical or numerical difficulties, such as true error analysis and adaptivity, modelling of multi-phase phenomena or fitting problems, stiff terms in convection/diffusion equations and sources. To overcome existing problems and to find solution methods for future applications requires many efforts and always new developments. The goal of The International Symposium on Finite Volumes for Complex Applica

  9. Organic weed control with vinegar: Application volumes and adjuvants

    Science.gov (United States)

    Preliminary results have indicated that vinegar has potential as an organic herbicide, but further research is needed to increase our understanding of the relationship between acetic acid concentrations, application volumes, adjuvants, weed species, and weed maturity on effectiveness of vinegar to c...

  10. A proposed application programming interface for a physical volume repository

    Science.gov (United States)

    Jones, Merritt; Williams, Joel; Wrenn, Richard

    1996-01-01

    The IEEE Storage System Standards Working Group (SSSWG) has developed the Reference Model for Open Storage Systems Interconnection, Mass Storage System Reference Model Version 5. This document, provides the framework for a series of standards for application and user interfaces to open storage systems. More recently, the SSSWG has been developing Application Programming Interfaces (APIs) for the individual components defined by the model. The API for the Physical Volume Repository is the most fully developed, but work is being done on APIs for the Physical Volume Library and for the Mover also. The SSSWG meets every other month, and meetings are open to all interested parties. The Physical Volume Repository (PVR) is responsible for managing the storage of removable media cartridges and for mounting and dismounting these cartridges onto drives. This document describes a model which defines a Physical Volume Repository, and gives a brief summary of the Application Programming Interface (API) which the IEEE Storage Systems Standards Working Group (SSSWG) is proposing as the standard interface for the PVR.

  11. An experimental result of estimating an application volume by machine learning techniques.

    Science.gov (United States)

    Hasegawa, Tatsuhito; Koshino, Makoto; Kimura, Haruhiko

    2015-01-01

    In this study, we improved the usability of smartphones by automating a user's operations. We developed an intelligent system using machine learning techniques that periodically detects a user's context on a smartphone. We selected the Android operating system because it has the largest market share and highest flexibility of its development environment. In this paper, we describe an application that automatically adjusts application volume. Adjusting the volume can be easily forgotten because users need to push the volume buttons to alter the volume depending on the given situation. Therefore, we developed an application that automatically adjusts the volume based on learned user settings. Application volume can be set differently from ringtone volume on Android devices, and these volume settings are associated with each specific application including games. Our application records a user's location, the volume setting, the foreground application name and other such attributes as learning data, thereby estimating whether the volume should be adjusted using machine learning techniques via Weka. PMID:25713755

  12. Application of finite volume method to free surface flow

    OpenAIRE

    Hoření, Bohumír

    2005-01-01

    The contribution deals with an application of discontinuous Galerkin method to free surface flow calculation. Both the super- and sub-critical flows are studied for steady and unsteady flow conditions. The numerical method is tested experimentally on flow over a broad crest weir of height to length ratio 1/8. Also VOF (volume of fluid) method is tested for the same geometrical configuration.

  13. Barnwell Nuclear Fuels Plant applicability study. Volume III. Appendices

    International Nuclear Information System (INIS)

    Volume III suppliees supporting information to assist Congress in making a decision on the optimum utilization of the Barnwell Nuclear Fuels Plant. Included are applicable fuel cycle policies; properties of reference fuels; description and evaluation of alternative operational (flue cycle) modes; description and evaluation of safeguards systems and techniques; description and evaluation of spiking technology; waste and waste solidification evaluation; and Department of Energy programs relating to nonproliferation

  14. Application of automated topography focus corrections for volume manufacturing

    Science.gov (United States)

    Wiltshire, Timothy J.; Liegl, Bernhard R.; Hwang, Emily M.; Lucksinger, Mark R.

    2010-03-01

    This work describes the implementation and performance of AGILE focus corrections for advanced photo lithography in volume production as well as advanced development in IBM's 300mm facility. In particular, a logic hierarchy that manages the air gage sub-system corrections to optimize tool productivity while sampling with sufficient frequency to ensure focus accuracy for stable production processes is described. The information reviewed includes: General AGILE implementation approaches; Sample focus correction contours for critical 45nm, 32nm, and 22nm applications; An outline of the IBM Advanced Process Control (APC) logic and system(s) that manage the focus correction sets; Long term, historical focus correction data for stable 45nm processes as well as development stage 32nm processes; Practical issues encountered and possible enhancements to the methodology.

  15. Sensors Applications, Volume 5, Sensors in Household Appliances

    Science.gov (United States)

    Tschulena, Guido; Lahrmann, Andreas

    2003-11-01

    A competent and comprehensive survey of current and future sensors applied in electronic household devices. Engineers and scientists will find here reports of an increase in product safety, efficiency and consumer comfort, coupled with a decrease in power consumption and water/wastewater. The book also looks at the customer appeal of advanced "intelligent" appliances, showing the heightened need for comprehensive information on their potentials and limitations. Taken as a whole, this series covers all major fields of application for commercial sensors, as well as their manufacturing techniques and major types. As such the series does not treat bulk sensors, but rather places strong emphasis on microsensors, microsystems and integrated electronic sensor packages. Each of the individual volumes is tailored to the needs and queries of readers from the relevant branch of industry.

  16. Turbine design and application volumes 1, 2, and 3

    Science.gov (United States)

    Glassman, Arthur J. (Editor)

    1994-01-01

    NASA has an interest in turbines related primarily to aeronautics and space applications. Airbreathing turbine engines provide jet and turboshaft propulsion, as well as auxiliary power for aircraft. Propellant-driven turbines provide rocket propulsion and auxiliary power for spacecraft. Closed-cycle turbine engines using inert gases, organic fluids, and metal fluids have been studied for providing long-duration electric power for spacecraft. Other applications of interest for turbine engines include land-vehicle (cars, trucks, buses, trains, etc.) propulsion power and ground-based electrical power. In view of the turbine-system interest and efforts at Lewis Research Center, a course entitled 'Turbine Design and Application' was presented during 1968-69 as part of the In-house Graduate Study Program. The course was somewhat revised and again presented in 1972-73. Various aspects of turbine technology were covered including thermodynamic and fluid-dynamic concepts, fundamental turbine concepts, velocity diagrams, losses, blade aerodynamic design, blade cooling, mechanical design, operation, and performance. The notes written and used for the course have been revised and edited for publication. Such a publication can serve as a foundation for an introductory turbine course, a means for self-study, or a reference for selected topics. Any consistent set of units will satisfy the equations presented. Two commonly used consistent sets of units and constant values are given after the symbol definitions. These are the SI units and the U.S. customary units. A single set of equations covers both sets of units by including all constants required for the U.S. customary units and defining as unity those not required for the SI units. Three volumes are compiled into one.

  17. Application of Cameron decomposition in the analysis of PSAR images%Cameron分解法在极化SAR图像分析中的应用

    Institute of Scientific and Technical Information of China (English)

    汪洋; 鲁加国; 张芬

    2006-01-01

    利用Cameron分解法对极化SAR图像进行分析,将目标的极化散射矩阵与8类具有特定散射机理的典型散射体匹配,根据匹配角度提出了一种分类算法,从而对地物目标进行分类;实验结果表明,该分类算法对于分类地物目标,进而分析其散射机理是十分有效的.

  18. Application of Finite Volume Method to Structural Stochastic Dynamics

    OpenAIRE

    Weidong Chen; Yanchun Yu; Ping Jia; Xiande Wu; Fengchao Zhang

    2013-01-01

    The stochastic dynamic problems were becoming more difficult after considering the influences of stochastic factors and the complexity of the dynamic problems. To this background, the finite volume method combined with Perturbation Method was proposed for the stochastic dynamic analysis. The equations of perturbation-finite volume method were derived; the explicit expressions between random response and basic random variables were given; the method of stochastic dynamic analysis was discussed...

  19. Anisotropic 3D texture synthesis with application to volume rendering

    DEFF Research Database (Denmark)

    Laursen, Lasse Farnung; Ersbøll, Bjarne Kjær; Bærentzen, Jakob Andreas

    2011-01-01

    images using a 12.1 megapixel camera. Next, we extend the volume rendering pipeline by creating a transfer function which yields not only color and opacity from the input intensity, but also texture coordinates for our synthesized 3D texture. Thus, we add texture to the volume rendered images....... This method is applied to a high quality visualization of a pig carcass, where samples of meat, bone, and fat have been used to produce the anisotropic 3D textures....

  20. Students' and Teachers' Application of Surface Area to Volume Relationships

    Science.gov (United States)

    Taylor, Amy R.; Jones, M. Gail

    2013-02-01

    The National Science Education Standards emphasize teaching unifying concepts and processes such as basic functions of living organisms, the living environment, and scale (NRC 2011). Scale includes understanding that different characteristics, properties, or relationships within a system might change as its dimensions are increased or decreased (NRC 2011). One such relationship involves surface area to volume which is a pervasive concept that can be found throughout different sciences. This concept is important for students to not only understand the association of the two, but to also be able to apply this relationship in science contexts. The purpose of this study is to investigate the factors that influence the understanding surface area to volume relationships. This study examined middle school students', high school students', and science teachers' logical thinking skills (including proportional reasoning), visual-spatial skills, and understandings of surface area to volume relationships. Regression results indicated that participants' reasoning abilities and components of visual-spatial skills could be possible predictors for one's ability to understand surface area to volume relationships. Implications for teaching scale concepts such as surface area to volume relationships in the science classroom are discussed.

  1. Volume rendering: application in static field conformal radiosurgery

    Science.gov (United States)

    Bourland, J. Daniel; Camp, Jon J.; Robb, Richard A.

    1992-09-01

    Lesions in the head which are large or irregularly shaped present challenges for radiosurgical treatment by linear accelerator or other radiosurgery modalities. To treat these lesions we are developing static field, conformal stereotactic radiosurgery. In this procedure seven to eleven megavoltage x-ray beams are aimed at the target volume. Each beam is designed from the beam's-eye view, and has its own unique geometry: gantry angle, table angle, and shape which conforms to the projected cross-section of the target. A difficulty with this and other 3- D treatment plans is the visualization of the treatment geometry and proposed treatment plan. Is the target volume geometrically covered by the arrangement of beams, and is the dose distribution adequate? To answer these questions we have been investigating the use of ANALYZETM volume rendering to display the target anatomy and the resultant dose distribution.

  2. Cooperative Instructional Application of Writing Research. Final Report. Volume Two.

    Science.gov (United States)

    Cronnell, Bruce; And Others

    The second of three volumes on the relationship between writing research and instruction, this report first describes a 1982 conference on writing policies and problems sponsored by the Educational Research and Development division of the Southwest Regional Laboratory (SWRL) and the California State University, Long Beach. The second section…

  3. Applications of texture mapping to volume and flow visualization

    Energy Technology Data Exchange (ETDEWEB)

    Max, N.; Crawfis, R.; Becker, B.

    1995-05-01

    The authors describe six visualization methods which take advantage of hardware polygon scan conversion, texture mapping, and compositing, to give interactive viewing of 3D scalar fields, and motion for 3D flows. For volume rendering, these are splatting of an optimized 3D reconstruction filter, and tetrahedral cell projection using a texture map to provide the exponential per pixel necessary for accurate opacity calculation. For flows, these are the above tetrahedral projection method for rendering the ``flow volume`` dyed after passing through a dye releasing polygon, ``splatting`` of cycled anisotropic textures to provide flow direction and motion visualization, splatting motion blurred particles to indicate flow velocity, and advecting a texture directly to show the flow motion. All these techniques are tailored to take advantage of existing graphics pipelines to produce interactive visualization tools.

  4. An experimental result of estimating an application volume by machine learning techniques

    OpenAIRE

    Hasegawa, Tatsuhito; Koshino, Makoto; Kimura, Haruhiko

    2015-01-01

    In this study, we improved the usability of smartphones by automating a user’s operations. We developed an intelligent system using machine learning techniques that periodically detects a user’s context on a smartphone. We selected the Android operating system because it has the largest market share and highest flexibility of its development environment. In this paper, we describe an application that automatically adjusts application volume. Adjusting the volume can be easily forgotten becaus...

  5. Dedicating Finite Volume Method to Electromagnetic Plasma Modeling: Circuit Breaker Application

    OpenAIRE

    Rondot, Loïc; Mazauric, Vincent; Delannoy, Yves; Meunier, Gérard

    2009-01-01

    For several applications including strong hydrodynamics constraints (like in a circuit breaker), Finite Element solvers are not suitable for fluid dynamical modeling. For these applications, the coupling between the Computational Fluid Dynamics and the electromagnetism modeling is not easy. In this context, a magnetodynamic formulation is developed using the Finite Volume Method to address specific issues in multiphysics involved in circuit breaker modeling. The principles of Finite Volume Me...

  6. CFD Applications in Energy and Environment Sectors: Volume 1

    Directory of Open Access Journals (Sweden)

    Maher A.R. Sadiq Al-Baghdadi and Hashim R. Abdol Hamid

    2012-01-01

    Full Text Available Chapter 1: Simulation and Modelling of Oxygen Coal Combustion with Flue Gas Recirculation. Chaouki Ghenai Chapter 2: The Choice of the Best Air Distribution Concept in Air-Conditioned Auditorium by Means of CFD Numerical Prediction. Barbara Lipska, Piotr Koper Chapter 3: CFD Applications in Natural Ventilation of Buildings and Air Quality Dispersion. N. Nikolopoulos, A. Nikolopoulos, I. Papadakis, K.-S. P. Nikas Chapter 4: CFD Modeling of Air Pollutant Transport and Dispersion. Labovský Juraj, Jelemenský Ľudovít Chapter 5: CFD Modeling of Multiphase Flow in Environmental Engineering. Masroor Mohajerani, Mehrab Mehrvar, Farhad Ein-Mozaffari Chapter 6: CFD Study on the Roles of Trees on Airflow and Pollutant Dispersion within Urban Street Canyons. Salim Mohamed Salim, Andrew Chan, Riccardo Buccolieri, Silvana Di Sabatino Chapter 7: Energy Efficiency and Air Quality in Hospitals Design. Essam E. Khalil Chapter 8: Application of CFD in Pulverized Fuel Combustion. M. Tayyeb Javed, Tahira Sultana Chapter 9: A Heat Transfer Model For Fluids Based on Cellular Automaton Application to an Air Conditioning of A Building. Andrés Saiz Martínez Chapter 10: CFD Application in Power Plants. Essam E. Khalil Chapter 11: Analysis and Computation of the Heat Charge/Discharge Behavior in Packed Bed Thermal Storage Systems. Pei-Wen Li, Jon Van Lew, Wafaa Karaki, Cho Lik Chan, Jake Stephens

  7. Multiagent Systems and Applications Volume 1Practice and Experience

    CERN Document Server

    Jain, Lakhmi

    2013-01-01

    The focus of the book is on completed implementations of agent-based software systems. Here, agent technology is considered broadly, starting from development of agent platforms, all the way through systems actually implemented. The covered topics also include lessons learned during implementation of agent platforms and the reflection on the process of development and application of agent-based systems.   The book includes 10 chapters where interested reader can find discussion of important issues encountered during development of well-known agent platforms such as JADE and Jadex as well as some interesting experiences in developing a new platform that combines software agent and Web Services. Furthermore, the book shows readers several valuable examples of applications based on multi-agent systems including simulations, agents in autonomous negotiations and agents in public administration modelling. We believe that the book will prove useful to the researchers, professors and the practitioners in all discip...

  8. Engineering Applications of Computational Fluid Dynamics: Volume 2

    Directory of Open Access Journals (Sweden)

    Maher A.R. Sadiq Al-Baghdadi

    2013-01-01

    Full Text Available Chapter 1: CFD Modeling of Methane Reforming in Compact Reformers. Meng Ni Chapter 2: FEM Based Solution of Thermo Fluid Dynamic Phenomena in Solid Oxide Fuel Cells (SOFCS. F. Arpino, A. Carotenuto, N. Massarotti, A. Mauro Chapter 3: Computational Fluid Dynamics in the Development of a 3D Simulator for Testing Pollution Monitoring Robotic Fishes. John Oyekan, Bowen Lu, Huosheng Hu Chapter 4: CFD Applications in Electronic Packaging. C.Y. Khor, Chun-Sean Lau, M.Z. Abdullah Chapter 5: CFD Simulation of Savonius Wind Turbine Operation. Jo?o Vicente Akwa, Adriane Prisco Petry Chapter 6: Intermittency Modelling of Transitional Boundary Layer Flows on Steam and Gas Turbine Blades. Erik Dick, Slawomir Kubacki, Koen Lodefier, Witold Elsner Chapter 7: Numerical Analysis of the Flow through Fitting in Air Conditioning Systems. N.C. Uz?rraga-Rodriguez, A. Gallegos-Mu?oz, J.M. Belman-Flores, J.C. Rubio-Arana Chapter 8: Design and Optimization of Food Processing Equipments using Computational Fluid Dynamics Modeling. N. Chhanwal and C. Anandharamakrishnan Chapter 9: Fuel and Intake Systems Optimization of a Converted LPG Engine: Steady and Unsteady in-Cylinder Flow CFD Investigations and Experiments Validation. M. A. Jemni, G. Kantchev, Z. Driss, M. S. Abid Chapter 10: Computational Fluid Dynamics Application for Thermal Management in Underground Mines. Agus P. Sasmito, Jundika C. Kurnia, Guan Mengzhao, Erik Birgersson, Arun S. Mujumdar Chapter 11: Computational Fluid Dynamics and its Applications. R.Parthiban, C.Muthuraj, A.Rajakumar

  9. Long discontinuous carbon fibre/polypropylene composites for high volume automotive applications

    OpenAIRE

    Burn, David T.

    2016-01-01

    The volume of fibre reinforced composites is increasing within the automotive industry, as stringent emissions legislation and consumer demands for improved fuel economy are encouraging manufacturers to reduce vehicular mass. Moreover, the falling cost of carbon fibre has meant that these composites are now being considered for semi-structural and structural components for medium-volume (+50,000ppa) applications in Euro Market Segments E and F (Jaguar XF, BMW 7 Series, Mercedes S-Class). ...

  10. Engineering Applications of Computational Fluid Dynamics: Volume 2

    OpenAIRE

    Maher A.R. Sadiq Al-Baghdadi

    2013-01-01

    Chapter 1: CFD Modeling of Methane Reforming in Compact Reformers. Meng Ni Chapter 2: FEM Based Solution of Thermo Fluid Dynamic Phenomena in Solid Oxide Fuel Cells (SOFCS). F. Arpino, A. Carotenuto, N. Massarotti, A. Mauro Chapter 3: Computational Fluid Dynamics in the Development of a 3D Simulator for Testing Pollution Monitoring Robotic Fishes. John Oyekan, Bowen Lu, Huosheng Hu Chapter 4: CFD Applications in Electronic Packaging. C.Y. Khor, Chun-Sean Lau, M.Z. Abdullah Chapter 5: CFD Simu...

  11. Aluminum Tailor-Welded Blanks for High Volume Automotive Applications

    Energy Technology Data Exchange (ETDEWEB)

    Hovanski, Yuri; Upadhyay, Piyush; Pilli, Siva Prasad; Carlson, Blair; Carsley, John; Hartfield-Wunsch, Susan; Eisenmenger, Mark

    2014-02-04

    A Design of Experiment based approach is used to systematically investigate relationships between 8 different welding factors (4 related to tool geometry, 4 related to weld process control) and resulting weld properties including strength, elongation and formability in 1.2mm-2mm thick friction stir welding of AA5182-O for TWB application. The factors that result in most significant effects are elucidated. The interactions between several key factors like plunge depth, tool tilt, pin feature and pin length on the overall weld quality is discussed. Appropriate levels of factors that lead to excellent weld properties are also identified.

  12. Data Mining Foundations and Intelligent Paradigms Volume 3 Medical, Health, Social, Biological and other Applications

    CERN Document Server

    Jain, Lakhmi

    2012-01-01

    Data mining is one of the most rapidly growing research areas in computer science and statistics. In Volume 3 of this three volume series, we have brought together contributions from some of the most prestigious researchers in applied data mining. Areas of application covered are diverse and include healthcare and finance. Each of the chapters is self contained. Statisticians, applied scientists/ engineers and researchers in bioinformatics will find this volume valuable. Additionally, it provides a sourcebook for graduate students interested in the current direction of research in applied data mining.

  13. Are urine flow-volume nomograms developed on Caucasian men optimally applicable for Indian men? Need for appraisal of flow-volume relations in local population

    OpenAIRE

    Agarwal, Mayank M.; Choudhury, Sunirmal; Mandal, Arup K.; Mavuduru, Ravimohan; Singh, Shrawan K.

    2010-01-01

    Introduction: Flow-volume nomograms and volume-corrected flow-rates (cQ) are tools to correct uroflow rates (Q) with varied voided volumes (VV) of urine. We investigated the applicability of the available nomograms in our local population. Materials and Methods: Raw data of our previous study on variation in Q with voiding position (standing, sitting, and squatting) in healthy adult men was reanalyzed. Additionally, the departmental urodynamic database of the last four years was searched for ...

  14. Grouting applications in civil engineering. Volume I and II

    International Nuclear Information System (INIS)

    A comprehensive description of grouting applications in civil engineering is presented that can serve as a basis for the selection of grouting methods in the borehole sealing problem. The breadth and depth of the study was assured by conducting the main part of the review, the collection and evaluation of information, without specifically considering the borehole sealing problem (but naturally incorporating any aspect of civil engineering applications that could be of potential use). Grouting is very much an art and not a science. In most cases, it is a trial and error procedure where an inexpensive method is initially tried and then a more expensive one is used until the desired results are obtained. Once a desired effect is obtained, it is difficult to credit any one procedure with the success because the results are due to the summation of all the methods used. In many cases, the method that proves successful reflects a small abnormality in the ground or structure rather than its overall characteristics. Hence, successful grouting relies heavily on good engineering judgement and experience, and not on a basic set of standard correlations or equations. 800 references

  15. Engineering Applications of Computational Fluid Dynamics: Volume 1

    Directory of Open Access Journals (Sweden)

    Maher A.R. Sadiq Al-Baghdadi

    2013-01-01

    Full Text Available Chapter 1: Filtered Density Function as a Modern CFD Tool. N. Ansari, F.A. Jaberi, M.R.H. Sheikhi, P. Givi Chapter 2: CFD Applications in Steam Boilers. N. Nikolopoulos, A. Nikolopoulos, E. Karambinis, M. Agraniotis, P. Grammelis, E. Kakaras Chapter 3: CFD Simulation on Human-Environment System. Shengwei Zhu Chapter 4: CFD Applications in Membrane Technology by Finite Element Analysis. José M. Gozálvez-Zafrilla, Asunción Santafé-Moros Chapter 5: CFD Modelling of Stirred Tanks. Z. Driss, M. Ammar, W. Chtourou, M.S. Abid Chapter 6: CFD Modeling and Simulations: Horizontal Deep Drilling Process and Filter Cake Formation. Mohd A. Kabir, Isaac K. Gamwo Chapter 7: CFD Simulation of Phase Particle Entrapment. Peymani F. Y., Ganbari S. A., Liu Y., Hayatdavoudi A. Chapter 8: Simulation of Low-Btu Syngas Combustion in Trapped Vortex Combustor. Khaled Zbeeb, Chaouki Ghenai Chapter 9: Experimental, Analytical and Numerical Investigation of a Swirling Submerged Jet Flow. H. Alighanbari, M. R. Amiralaei, S. Savtchenko Chapter 10: CFD Simulations of Two-Phase Flow. Yu Zhang Chapter 11: CFD Simulation of Syntrophic Anaerobic Digestion of Volatile Fatty Acids in a Continuous Stirred Reactor. T. Amani, S.M. Mousavi, M. Nosrati

  16. Thermal Storage Applications Workshop. Volume 2: Contributed Papers

    Science.gov (United States)

    1979-01-01

    The solar thermal and the thermal and thermochemical energy storage programs are described as well as the technology requirements for both external (electrical) and internal (thermal, chemical) modes for energy storage in solar power plants. Specific technical issues addressed include thermal storage criteria for solar power plants interfacing with utility systems; optimal dispatch of storage for solar plants in a conventional electric grid; thermal storage/temperature tradeoffs for solar total energy systems; the value of energy storage for direct-replacement solar thermal power plants; systems analysis of storage in specific solar thermal power applications; the value of seasonal storage of solar energy; criteria for selection of the thermal storage system for a 10 MW(2) solar power plant; and the need for specific requirements by storage system development teams.

  17. High Volume Fraction Carbon Nanotube Composites for Aerospace Applications

    Science.gov (United States)

    Siochi, E. J.; Kim, J.-W.; Sauti, G.; Cano, R. J.; Wincheski, R. A.; Ratcliffe, J. G.; Czabaj, M.

    2016-01-01

    Reported mechanical properties of carbon nanotubes (CNTs) at the nanoscale suggest their potential to enable significantly lighter structures of interest for space applications. However, their utility depends on the retention of these properties in bulk material formats that permit practical fabrication of large structures. This presentation summarizes recent progress made to produce carbon nanotube composites with specific tensile properties that begin to rival those of carbon fiber reinforced polymer composites. CNT content in these nanocomposites was greater than 70% by weight. Tested nanocomposite specimens were fabricated from kilometers or tens of square meters of CNT, depending on the starting material format. Processing methods to yield these results, and characterization and testing to evaluate the performance of these composites will be discussed. The final objective is the demonstration of a CNT composite overwrapped pressure vessel to be flight tested in the Fall of 2016.

  18. High Volume Fraction Carbon Nanotube Composites for Aerospace Applications

    Science.gov (United States)

    Siochi, Emilie J.; Kim, Jae-Woo; Sauti, Godfrey; Cano, Roberto J.; Wincheski, Russell A.; Ratcliffe, James G.; Czabaj, Michael; Jensen, Benjamin D.; Wise, Kristopher E.

    2015-01-01

    Reported nanoscale mechanical properties of carbon nanotubes (CNTs) suggest that their use may enable the fabrication of significantly lighter structures for use in space applications. To be useful in the fabrication of large structures, however, their attractive nanoscale properties must be retained as they are scaled up to bulk materials and converted into practically useful forms. Advances in CNT production have significantly increased the quantities available for use in manufacturing processes, but challenges remain with the retention of nanoscale properties in larger assemblies of CNTs. This work summarizes recent progress in producing carbon nanotube composites with tensile properties approaching those of carbon fiber reinforced polymer composites. These advances were achieved in nanocomposites with CNT content of 70% by weight. The processing methods explored to yield these CNT composite properties will be discussed, as will the characterization and test methods that were developed to provide insight into the factors that contribute to the enhanced tensile properties. Technology maturation was guided by parallel advancements in computational modeling tools that aided in the interpretation of experimental data.

  19. Composite materials. Volume 3 - Engineering applications of composites. Volume 4 - Metallic matrix composites. Volume 8 - Structural design and analysis, Part 2

    Science.gov (United States)

    Noton, B. R. (Editor); Kreider, K. G.; Chamis, C. C.

    1974-01-01

    This volume discusses a vaety of applications of both low- and high-cost composite materials in a number of selected engineering fields. The text stresses the use of fiber-reinforced composites, along with interesting material systems used in the electrical and nuclear industries. As to technology transfer, a similarity is noted between many of the reasons responsible for the utilization of composites and those problems requiring urgent solution, such as mechanized fabrication processes and design for production. Features topics include road transportation, rail transportation, civil aircraft, space vehicles, builing industry, chemical plants, and appliances and equipment. The laminate orientation code devised by Air Force materials laboratory is included. Individual items are announced in this issue.

  20. Uncooled amorphous silicon IRFPA for high performance and high volume applications

    Science.gov (United States)

    Pochic, D.; Durand, A.; Tissot, J. L.; Crastes, A.; Vilain, M.; Legras, O.; Tinnes, S.; Minassian, C.; Robert, P.

    2009-09-01

    For more than 10 years now, uncooled sensors have given new opportunities in the IR field of applications by being able to be produce in large volume. Compared to cooled technology, uncooled detectors offer many interesting advantages: high reliability, lower cost ... whereas the performance is high enough for a lot of applications. Thermography, building inspection, enhanced driver vision and military (thermal weapon sight, low altitude UAV sensor) are applications which can be provided with affordable IR focal plane arrays... As uncooled IR sensors are mainly dedicated to these high volume applications, any uncooled IRFPA technology has to be able to provide high performance sensors but also to be producible in large volume at a minimum cost. The high level of accumulated expertise by ULIS and CEA/LETI on uncooled microbolometers made from amorphous silicon layer enables ULIS to develop a full range of IRFPA formats from 160x120 to 1024x768 pixels with 25μm and 17μm pixel-pitch, designed for high end and high volume applications. The detector ROIC designs rely on a simple architecture (detector configuration addressed by a serial link for user defined amplifier gain, windowing capability...) which enables easier systems upgrade and therefore a reduced system development non recurrent cost. The packaging technique depends on the application environment and the production volume in order to fit with the market expectation. Starting from metallic and ceramics package, very advanced new technique is under development in order to reduce uncooled IRFPA production cost. NETD in the range of 30mK (f/1, 300K, 60Hz) as well as operability higher than 99.99%, are routinely achieved with amorphous silicon technology.

  1. High-energy molecular lasers self-controlled volume-discharge lasers and applications

    CERN Document Server

    Apollonov, V V

    2016-01-01

    This book displays the physics and design of high-power molecular lasers. The lasers described are self-controlled volume-discharge lasers. The book explains self-sustained discharge lasers, self-initiated discharge lasers and technical approaches to laser design. Important topics discussed are laser efficiency, laser beam quality and electric field homogeneity. The book contains many new innovative applications.

  2. Continuous modelling study of numerical volumes - Applications to the visualization of anatomical structures

    International Nuclear Information System (INIS)

    Several technics of imaging (IRM, image scanners, tomoscintigraphy, echography) give numerical informations presented by means of a stack of parallel cross-sectional images. Since many years, 3-D mathematical tools have been developed and allow the 3 D images synthesis of surfaces. In first part, we give the technics of numerical volume exploitation and their medical applications to diagnosis and therapy. The second part is about a continuous modelling of the volume with a tensor product of cubic splines. We study the characteristics of this representation and its clinical validation. Finally, we treat of the problem of surface visualization of objects contained in the volume. The results show the interest of this model and allow to propose specifications for 3-D workstation realization

  3. Joint modelling of flood peaks and volumes: A copula application for the Danube River

    Directory of Open Access Journals (Sweden)

    Papaioannou George

    2016-12-01

    Full Text Available Flood frequency analysis is usually performed as a univariate analysis of flood peaks using a suitable theoretical probability distribution of the annual maximum flood peaks or peak over threshold values. However, other flood attributes, such as flood volume and duration, are necessary for the design of hydrotechnical projects, too. In this study, the suitability of various copula families for a bivariate analysis of peak discharges and flood volumes has been tested. Streamflow data from selected gauging stations along the whole Danube River have been used. Kendall’s rank correlation coefficient (tau quantifies the dependence between flood peak discharge and flood volume settings. The methodology is applied to two different data samples: 1 annual maximum flood (AMF peaks combined with annual maximum flow volumes of fixed durations at 5, 10, 15, 20, 25, 30 and 60 days, respectively (which can be regarded as a regime analysis of the dependence between the extremes of both variables in a given year, and 2 annual maximum flood (AMF peaks with corresponding flood volumes (which is a typical choice for engineering studies. The bivariate modelling of the extracted peak discharge - flood volume couples is achieved with the use of the Ali-Mikhail-Haq (AMH, Clayton, Frank, Joe, Gumbel, Hüsler-Reiss, Galambos, Tawn, Normal, Plackett and FGM copula families. Scatterplots of the observed and simulated peak discharge - flood volume pairs and goodness-of-fit tests have been used to assess the overall applicability of the copulas as well as observing any changes in suitable models along the Danube River. The results indicate that for the second data sampling method, almost all of the considered Archimedean class copula families perform better than the other copula families selected for this study, and that for the first method, only the upper-tail-flat copulas excel (except for the AMH copula due to its inability to model stronger relationships.

  4. Higher-Order, Space-Time Adaptive Finite Volume Methods: Algorithms, Analysis and Applications

    Energy Technology Data Exchange (ETDEWEB)

    Minion, Michael

    2014-04-29

    The four main goals outlined in the proposal for this project were: 1. Investigate the use of higher-order (in space and time) finite-volume methods for fluid flow problems. 2. Explore the embedding of iterative temporal methods within traditional block-structured AMR algorithms. 3. Develop parallel in time methods for ODEs and PDEs. 4. Work collaboratively with the Center for Computational Sciences and Engineering (CCSE) at Lawrence Berkeley National Lab towards incorporating new algorithms within existing DOE application codes.

  5. Application of dual volume reconstruction technique in embolization of intracranial aneurysms

    Directory of Open Access Journals (Sweden)

    Xiang-hai ZHANG

    2014-03-01

    Full Text Available Objective To explore the value of dual volume reconstruction technique in Guglielmi detachable coil (GDC embolization of intracranial aneurysms. Methods Three-dimensional imaging data of 20 patients received GDC embolization of intracranial aneurysms from Jun. 2012 to Apr. 2013 were analyzed for dual volume reconstruction. The value of application of dual volume reconstruction was evaluated by the detection rate of coils bolus, degree of aneurysm occlusion, the length of aneurysm sac and aneurysm neck before and after embolization, and the characteristics and clinical value of the reconstructed images. Results  A total of 20 coil boluses were detected by dual volume reconstruction images, and the detection rate was 100%. Among all of 20 patients, no visualization of contrast medium in the aneurysm was found in 13 patients, while contrast agent was found in the aneurysm sac in 3 patients and in the aneurysm neck in 4 patients. The length of aneurysm neck and sac was somewhat changed before and after embolization with no statistically significant difference (P>0.05. The dual volume reconstruction could reveal coil bolus, vessels, cranium and fusion images, and the aneurysms could be shown by different imaging modes according to the clinical requirement. Conclusion Dual volume reconstruction technique can display the location of coil bolus, degree of occlusion and aneurysm size, and evaluate the embolization effect by multifarious imaging modes, providing a great deal of information for the evaluation of GDC embolization of intracranial aneurysm. DOI: 10.11855/j.issn.0577-7402.2014.02.13

  6. Draft Title 40 CFR 191 compliance certification application for the Waste Isolation Pilot Plant. Volume 4: Appendix BIR Volume 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-31

    This report consists of the waste stream profile for the WIPP transuranic waste baseline inventory at Lawrence Livermore National Laboratory. The following assumptions/modifications were made by the WTWBIR team in developing the LL waste stream profiles: since only current volumes were provided by LL, the final form volumes were assumed to be the same as the current volumes; the WTWBIR team had to assign identification numbers (IDs) to those LL waste streams not given an identifier by the site, the assigned identification numbers are consistent with the site reported numbers; LL Final Waste Form Groups were modified to be consistent with the nomenclature used in the WTWBID, these changes included word and spelling changes, the assigned Final Waste Form Groups are consistent with the information provided by LL; the volumes for the year 1993 were changed from an annual rate of generation (m{sup 3}/year) to a cumulative value (m{sup 3}).

  7. High field volume coil with unbalance current distribution for MRI applications of rodents

    Science.gov (United States)

    Marrufo, O. R.; Hernández, J.; Rodríguez, A. O.

    2010-12-01

    The development of transceiver volume coils for high field MRI is still a very dynamic field of investigation and development Temnikov has been recently proposed a new volume coil design, similar to the to the gradiometer coil. It is also claimed that it is possible to individually tune it with a single chip capacitor. This motivated the development of a coil prototype based on this idea for whole-body MRI of rodents at 7 Tesla. Electromagnetic simulations of the RF field generated by this coil design were previously performed to study its properties. Electromagnetic simulations were also conducted for a standard birdcage coil with similar dimensions for fare comparison. In all numerical simulations, an unbalanced currents distribution was assumed by applying half the current intensity to designated legs. This coil design operated in the transceiver mode and was linear-driven. The coil size was manufactured to accommodate small rodents. Numerical simulations showed a field uniformity improvement of our coil over the standard birdcage coil. A popular birdcage coil was also constructed to compare their performances. Phantom and rat images were acquired for both volume coils to prove the viability of this coil design for high field MRI applications and standard spin echo pulse sequences Thus, these preliminary results make this coil design a good candidate for MRI and MRS applications of high magnetic fields.

  8. Characterization of volume holographic optical elements recorded in Bayfol HX photopolymer for solar photovoltaic applications.

    Science.gov (United States)

    Marín-Sáez, Julia; Atencia, Jesús; Chemisana, Daniel; Collados, María-Victoria

    2016-03-21

    Volume Holographic Optical Elements (HOEs) present interesting characteristics for photovoltaic applications as they can select spectrum for concentrating the target bandwidth and avoiding non-desired wavelengths, which can cause the decrease of the performance on the cell, for instance by overheating it. Volume HOEs have been recorded on Bayfol HX photopolymer to test the suitability of this material for solar concentrating photovoltaic systems. The HOEs were recorded at 532 nm and provided a dynamic range, reaching close to 100% efficiency at 800 nm. The diffracted spectrum had a FWHM of 230 nm when illuminating at Bragg angle. These characteristics prove HOEs recorded on Bayfol HX photopolymer are suitable for concentrating solar light onto photovoltaic cells sensitive to that wavelength range. PMID:27136889

  9. Application of three-dimensional digital image processing for reconstruction of microstructural volume from serial sections

    Energy Technology Data Exchange (ETDEWEB)

    Tewari, A.; Gokhale, A.M.

    2000-03-01

    Three-dimensional digital image processing is useful for reconstruction of microstructural volume from a stack of serial sections. Application of this technique is demonstrated via reconstruction of a volume segment of the liquid-phase sintered microstructure of a tungsten heavy alloy processed in the microgravity environment of NASA's space shuttle, Columbia. Ninety serial sections (approximately one micrometer apart) were used for reconstruction of the three-dimensional microstructure. The three-dimensional microstructural reconstruction clearly revealed that the tungsten grains are almost completely connected in three-dimensional space. Both the matrix and the grains are topologically co-continuous, although the alloy was liquid-phase sintered in microgravity. Therefore, absence of gravity did not produced a microstructure consisting of discrete isolated W grains uniformly dispersed in the liquid Ni-Fe alloy matrix at the sintering temperature.

  10. Characterization of volume holographic optical elements recorded in Bayfol HX photopolymer for solar photovoltaic applications.

    Science.gov (United States)

    Marín-Sáez, Julia; Atencia, Jesús; Chemisana, Daniel; Collados, María-Victoria

    2016-03-21

    Volume Holographic Optical Elements (HOEs) present interesting characteristics for photovoltaic applications as they can select spectrum for concentrating the target bandwidth and avoiding non-desired wavelengths, which can cause the decrease of the performance on the cell, for instance by overheating it. Volume HOEs have been recorded on Bayfol HX photopolymer to test the suitability of this material for solar concentrating photovoltaic systems. The HOEs were recorded at 532 nm and provided a dynamic range, reaching close to 100% efficiency at 800 nm. The diffracted spectrum had a FWHM of 230 nm when illuminating at Bragg angle. These characteristics prove HOEs recorded on Bayfol HX photopolymer are suitable for concentrating solar light onto photovoltaic cells sensitive to that wavelength range.

  11. On-Line Monitoring of Instrument Channel Performance: Volume 3: Applications to Nuclear Power Plant Technical Specification Instrumentation

    International Nuclear Information System (INIS)

    This report is a guide for a technical specification change submittal and subsequent implementation of on-line monitoring for safety-related applications. This report is the third in a three-volume set. Volume 1, ''Guidelines for Model Development and Implementation'', presents the various tasks that must be completed to prepare models for and to implement an on-line monitoring system

  12. Application of rock mechanics to cut-and-fill mining. Volume 2

    Energy Technology Data Exchange (ETDEWEB)

    1980-05-15

    The conference on application of rock mechanics to cut-and-fill mining was held June 1-3, 1980, at the University of Luleaa, Sweden. The papers in this volume deal almost entirely with the Naesliden project in Sweden. Stress measurements were made on the rock mass before and during mining and complex computer codes using the finite element method developed to calculate the strains and their changes as mining developed. Major problems involved the effects of joints and the mechanical properties of the hydraulic backfill and in corporating these items in the calculations. Most papers were entered individually into EDB. (LTN)

  13. 7th International Symposium on Applications of Laser Techniques to Fluid Mechanics, volume 2

    Science.gov (United States)

    1994-07-01

    The proceedings volumes 1 and 2 comprise the papers that were accepted for presentation at the Seventh International Symposium on Applications of Laser Techniques to Fluid Mechanics held at The Calouste Gulbenkian Foundation in Lisbon, during the period of July 11 to 14, 1994. The prime objective of this Seventh Symposium is to provide a forum for the presentation of the most advanced research on laser techniques for flow measurements, and reveal significant results to fluid mechanics. The applications of laser techniques to scientific and engineering fluid flow research is emphasized, but contributions to the theory and practice of laser methods are also considered where they facilitate new improved fluid mechanic research. Attention is focused on laser-Doppler anemometry, particle sizing and other methods for the measurement of velocity and scalars such as particle image velocimetry and laser induced fluorescence.

  14. 7th International Symposium on Applications of Laser Techniques to Fluid Mechanics, volume 1

    Science.gov (United States)

    1994-07-01

    The proceedings volumes 1 and 2 comprise the papers that were accepted for presentation at the Seventh International Symposium on Applications of Laser Techniques to Fluid Mechanics held at The Calouste Gulbenkian Foundation in Lisbon, during the period of July 11 to 14, 1994. The prime objective of this Seventh Symposium is to provide a forum for the presentation of the most advanced research on laser techniques for flow measurements, and reveal significant results to fluid mechanics. The applications of laser techniques to scientific and engineering fluid flow research is emphasized, but contributions to the theory and practice of laser methods are also considered where they facilitate new improved fluid mechanics research. Attention is focused on laser-Doppler anemometry, particle sizing and other methods for the measurement of velocity and scalars such as particle image velocimetry and laser induced fluorescence.

  15. Electrokinetic applications for environmental restoration, waste volume reduction, and contaminant containment systems

    International Nuclear Information System (INIS)

    In the US and all over the world, following over 50 years of nuclear arms production operations, the magnitude of resultant environmental damage is only beginning to surface. The US Department of Energy estimates that by the year 2070, the total volume of high-level waste, transuranic waste, low-level waste, and low-level mixed waste, generated as a result of past and current nuclear activities, will exceed 20 million cubic meters. In Russia, it is reported that more than 30% of all groundwater is contaminated with agricultural and industrial chemical waste. Government agencies today are faced with the responsibility of developing technologies that are suitable for dealing with severe environmental contamination and accumulating waste inventories. In response to this demand, applications of electrokinetics have emerged in the field of environmental waste management as alternatives for environmental decontamination and ecological protection. Electrokinetics involves the movement of charged species under the influence of an applied electric field and is applicable in several areas of environmental waste management, including cleanup of soil and groundwater, barrier detection, and emergency or protective fencing. The worldwide interest in this technology has steadily escalated over the past decade. Today, state-of-the-art applications of electrokinetics have been demonstrated in the US, The Netherlands, Russia, The Ukraine, and India. This paper addresses the latest advances in the various applications of this technology as well as the most significant breakthroughs in the history of electrokinetics

  16. Application of Hydrogel in Reconstruction Surgery: Hydrogel/Fat Graft Complex Filler for Volume Reconstruction in Critical Sized Muscle Defects.

    Science.gov (United States)

    Lui, Y F; Ip, W Y

    2016-01-01

    Autogenic fat graft usually suffers from degeneration and volume shrinkage in volume reconstruction applications. How to maintain graft viability and graft volume is an essential consideration in reconstruction therapies. In this presented investigation, a new fat graft transplantation method was developed aiming to improve long term graft viability and volume reconstruction effect by incorporation of hydrogel. The harvested fat graft is dissociated into small fragments and incorporated into a collagen based hydrogel to form a hydrogel/fat graft complex for volume reconstruction purpose. In vitro results indicate that the collagen based hydrogel can significantly improve the survivability of cells inside isolated graft. In a 6-month investigation on artificial created defect model, this hydrogel/fat graft complex filler has demonstrated the ability of promoting fat pad formation inside the targeted defect area. The newly generated fat pad can cover the whole defect and restore its original dimension in 6-month time point. Compared to simple fat transplantation, this hydrogel/fat graft complex system provides much improvement on long term volume restoration effect against degeneration and volume shrinkage. One notable effect is that there is continuous proliferation of adipose tissue throughout the 6-month period. In summary, the hydrogel/fat graft system presented in this investigation demonstrated a better and more significant effect on volume reconstruction in large sized volume defect than simple fat transplantation. PMID:27446947

  17. Formation of superpower volume discharges and their application for modification of surface of metals

    Science.gov (United States)

    Tarasenko, Victor F.; Shulepov, M. A.

    2008-05-01

    The results of experimental investigations of a volume avalanche discharge initiated by an e-beam (VADIEB) and surface layer of Cu and AlBe foils modifications at the plasma action of VADIEB are given. The volume discharge in the air of atmosphere pressure formed in the gap with the cathode having small curvature radius and with high voltage pulses of nanosecond duration and positive and negative polarity. A supershort avalanche electron beam (SAEB) with formation conditions in gases under atmospheric pressure have been investigated. It is proved that the surface layer is cleared of carbon at foil treatment, and atoms of oxygen penetrate into a foil. It is show that the cleaning depth depends on polarity of voltage pulses. At positive polarity of a copper foil electrode the cleaning is observed at the depth over 50 nm, and atoms of oxygen penetrate at the depth up to 25 nm. Plasma of the superpower volume discharge of nanosecond duration with a specific excitation power of hundreds of MW/cm3, and SAEB, and the discharge plasma radiation of various spectral ranges (including UV, VUV and X-ray) has the influence on the anode. The supershort avalanche electronic beam is generated only at negative polarity of a voltage pulse on an electrode with a small radius of curvature. SAEB influence on modifications of the copper foil surface is registered. VADIEB is easily realized in various gases and at various pressures, and, at gas pressure decrease the density of the beam current in helium can achieve 2 kA/cm2. It allows predicting an opportunity of VADIEB application for metal surface modifications in various technological processes, and for surface dielectric modifications at the certain design of the anode.

  18. Multiplexed Volume Bragg Gratings in Narrowand Broad-band Spectral Systems: Analysis and Application

    Science.gov (United States)

    Ingersoll, Gregory B.

    Volume Bragg gratings (VBGs) are important holographic optical elements in many spectral systems. Using multiple volume gratings, whether multiplexed or arranged sequentially, provides advantages to many types of systems in overall efficiency, dispersion performance, flexibility of design, etc. However, the use of multiple gratings---particularly when the gratings are multiplexed in a single holographic optical element (HOE)---is subject to inter-grating coupling effects that ultimately limit system performance. Analyzing these coupling effects requires a more complex mathematical model than the straightforward analysis of a single volume grating. We present a matrix-based algorithm for determining diffraction efficiencies of significant coupled waves in these multiplexed grating holographic optical elements (HOEs). Several carefully constructed experiments with spectrally multiplexed gratings in dichromated gelatin verify our conclusions. Applications of this theory to broad- and narrow-band systems are explored in detailed simulations. Broadband systems include spectrum splitters for diverse-bandgap photovoltaic (PV) cells. Volume Bragg gratings can serve as effective spectrum splitters, but the inherent dispersion of a VBG can be detrimental given a broad-spectrum input. The performance of a holographic spectrum splitter element can be improved by utilizing multiple volume gratings, each operating in a slightly different spectral band. However, care must be taken to avoid inter-grating coupling effects that limit ultimate performance. We explore broadband multi-grating holographic optical elements (HOEs) in sandwiched arrangements where individual single-grating HOEs are placed in series, and in multiplexed arrangements where multiple gratings are recorded in a single HOE. Particle swarm optimization (PSO) is used to tailor these systems to the solar spectrum taking into account both efficiency and dispersion. Both multiplexed and sandwiched two-grating systems

  19. Application of Local Discretization Methods in the NASA Finite-Volume General Circulation Model

    Science.gov (United States)

    Yeh, Kao-San; Lin, Shian-Jiann; Rood, Richard B.

    2002-01-01

    We present the basic ideas of the dynamics system of the finite-volume General Circulation Model developed at NASA Goddard Space Flight Center for climate simulations and other applications in meteorology. The dynamics of this model is designed with emphases on conservative and monotonic transport, where the property of Lagrangian conservation is used to maintain the physical consistency of the computational fluid for long-term simulations. As the model benefits from the noise-free solutions of monotonic finite-volume transport schemes, the property of Lagrangian conservation also partly compensates the accuracy of transport for the diffusion effects due to the treatment of monotonicity. By faithfully maintaining the fundamental laws of physics during the computation, this model is able to achieve sufficient accuracy for the global consistency of climate processes. Because the computing algorithms are based on local memory, this model has the advantage of efficiency in parallel computation with distributed memory. Further research is yet desirable to reduce the diffusion effects of monotonic transport for better accuracy, and to mitigate the limitation due to fast-moving gravity waves for better efficiency.

  20. Seismic hazard analysis application of methodology, results, and sensitivity studies. Volume 4

    Energy Technology Data Exchange (ETDEWEB)

    Bernreuter, D. L

    1981-08-08

    As part of the Site Specific Spectra Project, this report seeks to identify the sources of and minimize uncertainty in estimates of seismic hazards in the Eastern United States. Findings are being used by the Nuclear Regulatory Commission to develop a synthesis among various methods that can be used in evaluating seismic hazard at the various plants in the Eastern United States. In this volume, one of a five-volume series, we discuss the application of the probabilistic approach using expert opinion. The seismic hazard is developed at nine sites in the Central and Northeastern United States, and both individual experts' and synthesis results are obtained. We also discuss and evaluate the ground motion models used to develop the seismic hazard at the various sites, analyzing extensive sensitivity studies to determine the important parameters and the significance of uncertainty in them. Comparisons are made between probabilistic and real spectral for a number of Eastern earthquakes. The uncertainty in the real spectra is examined as a function of the key earthquake source parameters. In our opinion, the single most important conclusion of this study is that the use of expert opinion to supplement the sparse data available on Eastern United States earthquakes is a viable approach for determining estimted seismic hazard in this region of the country. 29 refs., 15 tabs.

  1. Introducing the Jacobian-volume-histogram of deforming organs: application to parotid shrinkage evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Fiorino, Claudio; Maggiulli, Eleonora; Broggi, Sara; Cattaneo, Giovanni Mauro; Calandrino, Riccardo [Medical Physics, San Raffaele Scientific Institute, Milano (Italy); Liberini, Simone; Faggiano, Elena; Rizzo, Giovanna [Institute of Molecular Bioimaging and Physiology, CNR, Segrate (Italy); Dell' Oca, Italo; Di Muzio, Nadia, E-mail: fiorino.claudio@hsr.it [Radiotherapy, San Raffaele Scientific Institute, Milano (Italy)

    2011-06-07

    The Jacobian of the deformation field of elastic registration between images taken during radiotherapy is a measure of inter-fraction local deformation. The histogram of the Jacobian values (Jac) within an organ was introduced (JVH-Jacobian-volume-histogram) and first applied in quantifying parotid shrinkage. MVCTs of 32 patients previously treated with helical tomotherapy for head-neck cancers were collected. Parotid deformation was evaluated through elastic registration between MVCTs taken at the first and last fractions. Jac was calculated for each voxel of all parotids, and integral JVHs were calculated for each parotid; the correlation between the JVH and the planning dose-volume histogram (DVH) was investigated. On average, 82% ({+-}17%) of the voxels shrinks (Jac < 1) and 14% ({+-}17%) shows a local compression >50% (Jac < 0.5). The best correlation between the DVH and the JVH was found between V10 and V15, and Jac < 0.4-0.6 (p < 0.01). The best constraint predicting a higher number of largely compressing voxels (Jac0.5<7.5%, median value) was V15 {>=} 75% (OR: 7.6, p = 0.002). Jac and the JVH are promising tools for scoring/modelling toxicity and for evaluating organ/contour variations with potential applications in adaptive radiotherapy.

  2. Environmental fate model for ultra-low-volume insecticide applications used for adult mosquito management

    Science.gov (United States)

    Schleier, Jerome J.; Peterson, Robert K.D.; Irvine, Kathryn M.; Marshall, Lucy M.; Weaver, David K.; Preftakes, Collin J.

    2012-01-01

    One of the more effective ways of managing high densities of adult mosquitoes that vector human and animal pathogens is ultra-low-volume (ULV) aerosol applications of insecticides. The U.S. Environmental Protection Agency uses models that are not validated for ULV insecticide applications and exposure assumptions to perform their human and ecological risk assessments. Currently, there is no validated model that can accurately predict deposition of insecticides applied using ULV technology for adult mosquito management. In addition, little is known about the deposition and drift of small droplets like those used under conditions encountered during ULV applications. The objective of this study was to perform field studies to measure environmental concentrations of insecticides and to develop a validated model to predict the deposition of ULV insecticides. The final regression model was selected by minimizing the Bayesian Information Criterion and its prediction performance was evaluated using k-fold cross validation. Density of the formulation and the density and CMD interaction coefficients were the largest in the model. The results showed that as density of the formulation decreases, deposition increases. The interaction of density and CMD showed that higher density formulations and larger droplets resulted in greater deposition. These results are supported by the aerosol physics literature. A k-fold cross validation demonstrated that the mean square error of the selected regression model is not biased, and the mean square error and mean square prediction error indicated good predictive ability.

  3. DAO's Finite-volume/Physical-space Data Assimilation System: Stratospheric Applications

    Science.gov (United States)

    daSilva, Arlindo; Lin, S.-J.; Einaudi, Franco (Technical Monitor)

    2000-01-01

    In this talk we describe the next-generation data assimilation system being developed at NASA's Data Assimilation Office (DAO), with emphasis on the applications to stratospheric forecasts and stratospheric constituent transport. This data assimilation system includes the General Circulation Model jointly developed by the DAO and the Climate and Global Dynamics Division (CGDD) at NCAR. This model is based on the finite-volume dynamical core) developed at DAO with physical parameterizations from the NCAR Climate Community Model. The Physical-space Statistical Analysis System (PSAS) is used to combine a first guess from the NASA-NCAR GCM with observational data to provide an updated estimate of the state of the atmosphere. Case studies for the (northern) Winter of 2000 will be discussed.

  4. Applications of a finite-volume algorithm for incompressible MHD problems

    CERN Document Server

    Vantieghem, S; Jackson, A

    2016-01-01

    We present the theory, algorithms and implementation of a parallel finite-volume algorithm for the solution of the incompressible magnetohydrodynamic (MHD) equations using unstructured grids that are applicable for a wide variety of geometries. Our method implements a mixed Adams-Bashforth/Crank-Nicolson scheme for the nonlinear terms in the MHD equations and we prove that it is stable independent of the time step. To ensure that the solenoidal condition is met for the magnetic field, we use a method whereby a pseudo-pressure is introduced into the induction equation; since we are concerned with incompressible flows, the resulting Poisson equation for the pseudo-pressure is solved alongside the equivalent Poisson problem for the velocity field. We validate our code in a variety of geometries including periodic boxes, spheres, spherical shells, spheroids and ellipsoids; for the finite geometries we implement the so-called ferromagnetic or pseudo-vacuum boundary conditions appropriate for a surrounding medium w...

  5. Automatic delineation of functional volumes in emission tomography for oncology applications

    International Nuclear Information System (INIS)

    One of the main factors of error for semi-quantitative analysis in positron emission tomography (PET) imaging for diagnosis and patient follow up, as well as new flourishing applications like image guided radiotherapy, is the methodology used to define the volumes of interest in the functional images. This is explained by poor image quality in emission tomography resulting from noise and partial volume effects induced blurring, as well as the variability of acquisition protocols, scanner models and image reconstruction procedures. The large number of proposed methodologies for the definition of a PET volume of interest does not help either. The majority of such proposed approaches are based on deterministic binary thresholding that are not robust to contrast variation and noise. In addition, these methodologies are usually unable to correctly handle heterogeneous uptake inside tumours. The objective of this thesis is to develop an automatic, robust, accurate and reproducible 3D image segmentation approach for the functional volumes determination of tumours of all sizes and shapes, and whose activity distribution may be strongly heterogeneous. The approach we have developed is based on a statistical image segmentation framework, combined with a fuzzy measure, which allows to take into account both noisy and blurry properties of nuclear medicine images. It uses a stochastic iterative parameters estimation and a locally adaptive model of the voxel and its neighbours for the estimation and segmentation. The developed approaches have been evaluated using a large array of datasets, comprising both simulated and real acquisitions of phantoms and tumours. The results obtained on phantom acquisitions allowed to validate the accuracy of the segmentation with respect to the size of considered structures, down to 13 mm in diameter (about twice the spatial resolution of a typical PET scanner), as well as its robustness with respect to noise, contrast variation, acquisition

  6. Comparison of different application systems and CT-assisted treatment planning procedures in the treatment of primary endometrium carcinoma. Is it technically possible to include the whole uterus volume in the volume treated by brachytherapy?

    International Nuclear Information System (INIS)

    In a consecutive series of 10 patients with primary irradiated endometrial carcinoma we analyzed the correlation between target volume and treated volume using either standard 1-channel applicators or individual Heyman-applicators. Application of the ovoids was followed by a planning CT scan for all patients. Based on this, target volume (uterus volume) was estimated on a 3D-planning system. According to the measurable length of the uterus cavity we determined the corresponding standard 1-channel applicator and calculated the respectively treated volume. Estimating the advantages of an optimized treatment planning strategy for individual Heyman-applications we compared the treated volumes, which result from a standardized and optimized treatment planning procedure. The mean uterus volume was 180 cm3 (range 57 to 316 cm3). Asymmetric uterus configurations with longitudinal or sagittal side differences exceeding 1 cm were found in 40% of the cases. Using standard 1-channel applicators on average 47% (range 25 to 89%) of the uterus volume were enclosed by the treated volume compared to 70% for Heyman-applications. Differentiating these individual applications according to the variable treatment modality values of mean 66% (range 36 to 110%) for the standardized and 73% (range 48 to 95%) for the optimized treatment planning strategy were found. Moreover optimized planning modalities led to an improved coverage of the target volume in 5 out of 10 cases with an increase in volume of 20% on average (range 11 to 32%). In 3 cases changes of less than 5% were noticed (no improvement). In order to protect organs at risk treated volume had to be decreased in 2 cases for 19% and 40% respectively. (orig./MG)

  7. Application Level Protocol Development for Library and Information Science Applications. Volume 1: Service Definition. Volume 2: Protocol Specification. Report No. TG.1.5; TG.50.

    Science.gov (United States)

    Aagaard, James S.; And Others

    This two-volume document specifies a protocol that was developed using the Reference Model for Open Systems Interconnection (OSI), which provides a framework for communications within a heterogeneous network environment. The protocol implements the features necessary for bibliographic searching, record maintenance, and mail transfer between…

  8. Personnel neutron dose assessment upgrade: Volume 2, Field neutron spectrometer for health physics applications

    International Nuclear Information System (INIS)

    Both the (ICRP) and the (NCPR) have recommended an increase in neutron quality factors and the adoption of effective dose equivalent methods. The series of reports entitled Personnel Neutron Dose Assessment Upgrade (PNL-6620) addresses these changes. Volume 1 in this series of reports (Personnel Neutron Dosimetry Assessment) provided guidance on the characteristics, use, and calibration of personnel neutron dosimeters in order to meet the new recommendations. This report, Volume 2: Field Neutron Spectrometer for Health Physics Applications describes the development of a portable field spectrometer which can be set up for use in a few minutes by a single person. The field spectrometer described herein represents a significant advance in improving the accuracy of neutron dose assessment. It permits an immediate analysis of the energy spectral distribution associated with the radiation from which neutron quality factor can be determined. It is now possible to depart from the use of maximum Q by determining and realistically applying a lower Q based on spectral data. The field spectrometer is made up of two modules: a detector module with built-in electronics and an analysis module with a IBM PC/reg sign/-compatible computer to control the data acquisition and analysis of data in the field. The unit is simple enough to allow the operator to perform spectral measurements with minimal training. The instrument is intended for use in steady-state radiation fields with neutrons energies covering the fission spectrum range. The prototype field spectrometer has been field tested in plutonium processing facilities, and has been proven to operate satisfactorily. The prototype field spectrometer uses a 3He proportional counter to measure the neutron energy spectrum between 50 keV and 5 MeV and a tissue equivalent proportional counter (TEPC) to measure absorbed neutron dose

  9. Resource Conservation and Recovery Act, Part B permit application [for the Waste Isolation Pilot Plant (WIPP)]. Volume 1, Revision 3

    Energy Technology Data Exchange (ETDEWEB)

    1993-03-01

    This volume includes the following chapters: Waste Isolation Pilot Plant RCRA A permit application; facility description; waste analysis plan; groundwater monitoring; procedures to prevent hazards; RCRA contingency plan; personnel training; corrective action for solid waste management units; and other Federal laws.

  10. ESTABLISHMENT OF DESIGN CRITERIA FOR OPTIMUM BURNERS FOR APPLICATION TO HEAVY FUEL FIRED PACKAGE BOILERS. VOLUME 2. PILOT SCALE TESTS

    Science.gov (United States)

    The report gives results of a research program to develop low-NOx heavy oil burners for application to industrial package boilers. Volume I documents Phase 1 of the program, bench scale studies which defined optimum conditions for two-stage combustion. The information led to a co...

  11. ESTABLISHMENT OF DESIGN CRITERIA FOR OPTIMUM BURNERS FOR APPLICATION TO HEAVY FUEL FIRED PACKAGE BOILERS. VOLUME 1. LABORATORY SCALE TESTS

    Science.gov (United States)

    The report gives results of a research program to develop low-NOx heavy oil burners for application to industrial package boilers. Volume I documents Phase 1 of the program, bench scale studies which defined optimum conditions for two-stage combustion. The information led to a co...

  12. Application of adaptive and neural network computational techniques to Traffic Volume and Classification Monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Mead, W.C.; Fisher, H.N.; Jones, R.D.; Bisset, K.R.; Lee, L.A.

    1993-09-01

    We are developing a Traffic Volume and Classification Monitoring (TVCM) system based on adaptive and neural network computational techniques. The value of neutral networks in this application lies in their ability to learn from data and to form a mapping of arbitrary topology. The piezoelectric strip and magnetic loop sensors typically used for TVCM provide signals that are complicated and variable, and that correspond in indirect ways with the desired FWHA 13-class classification system. Further, the wide variety of vehicle configurations adds to the complexity of the classification task. Our goal is to provide a TVCM system featuring high accuracy, adaptability to wide sensor and envirorunental variations, and continuous fault detection. We have instrumented an experimental TVCM site, developed PC-based on-line data acquisition software, collected a large database of vehicles` signals together with accurate ground truth determination, and analyzed the data off-line with a neural net classification system that can distinguish between class 2 (automobiles) and class 3 (utility vehicles) with better than 90% accuracy. The neural network used, called the Connectionist Hyperprism Classification (CHC) network, features simple basis functions; rapid, linear training algorithms for basis function amplitudes and widths; and basis function elimination that enhances network speed and accuracy. Work is in progress to extend the system to other classes, to quantify the system`s adaptability, and to develop automatic fault detection techniques.

  13. Lung Volume Reduction After Stereotactic Ablative Radiation Therapy of Lung Tumors: Potential Application to Emphysema

    Energy Technology Data Exchange (ETDEWEB)

    Binkley, Michael S. [Department of Radiation Oncology, Stanford University School of Medicine, Stanford, California (United States); Shrager, Joseph B. [Division of Thoracic Surgery, Department of Cardiothoracic Surgery, Stanford University School of Medicine, Stanford, California (United States); Stanford Cancer Institute, Stanford University School of Medicine, Stanford, California (United States); Leung, Ann N. [Department of Radiology, Stanford University School of Medicine, Stanford, California (United States); Popat, Rita [Department of Health Research and Policy, Stanford University School of Medicine, Stanford, California (United States); Trakul, Nicholas [Department of Radiation Oncology, Stanford University School of Medicine, Stanford, California (United States); Department of Radiation Oncology, University of Southern California Keck School of Medicine, Los Angeles, California (United States); Atwood, Todd F.; Chaudhuri, Aadel [Department of Radiation Oncology, Stanford University School of Medicine, Stanford, California (United States); Maxim, Peter G. [Department of Radiation Oncology, Stanford University School of Medicine, Stanford, California (United States); Stanford Cancer Institute, Stanford University School of Medicine, Stanford, California (United States); Diehn, Maximilian, E-mail: Diehn@Stanford.edu [Department of Radiation Oncology, Stanford University School of Medicine, Stanford, California (United States); Stanford Cancer Institute, Stanford University School of Medicine, Stanford, California (United States); Institute for Stem Cell Biology and Regenerative Medicine, Stanford University School of Medicine, Stanford, California (United States); Loo, Billy W., E-mail: BWLoo@Stanford.edu [Department of Radiation Oncology, Stanford University School of Medicine, Stanford, California (United States); Stanford Cancer Institute, Stanford University School of Medicine, Stanford, California (United States)

    2014-09-01

    Purpose: Lung volume reduction surgery (LVRS) improves dyspnea and other outcomes in selected patients with severe emphysema, but many have excessive surgical risk for LVRS. We analyzed the dose-volume relationship for lobar volume reduction after stereotactic ablative radiation therapy (SABR) of lung tumors, hypothesizing that SABR could achieve therapeutic volume reduction if applied in emphysema. Methods and Materials: We retrospectively identified patients treated from 2007 to 2011 who had SABR for 1 lung tumor, pre-SABR pulmonary function testing, and ≥6 months computed tomographic (CT) imaging follow-up. We contoured the treated lobe and untreated adjacent lobe(s) on CT before and after SABR and calculated their volume changes relative to the contoured total (bilateral) lung volume (TLV). We correlated lobar volume reduction with the volume receiving high biologically effective doses (BED, α/β = 3). Results: 27 patients met the inclusion criteria, with a median CT follow-up time of 14 months. There was no grade ≥3 toxicity. The median volume reduction of the treated lobe was 4.4% of TLV (range, −0.4%-10.8%); the median expansion of the untreated adjacent lobe was 2.6% of TLV (range, −3.9%-11.6%). The volume reduction of the treated lobe was positively correlated with the volume receiving BED ≥60 Gy (r{sup 2}=0.45, P=.0001). This persisted in subgroups determined by high versus low pre-SABR forced expiratory volume in 1 second, treated lobe CT emphysema score, number of fractions, follow-up CT time, central versus peripheral location, and upper versus lower lobe location, with no significant differences in effect size between subgroups. Volume expansion of the untreated adjacent lobe(s) was positively correlated with volume reduction of the treated lobe (r{sup 2}=0.47, P<.0001). Conclusions: We identified a dose-volume response for treated lobe volume reduction and adjacent lobe compensatory expansion after lung tumor SABR, consistent across

  14. Application of a High Order Finite Volume Scheme on Unstructured Grids to Fluid Dynamics and Aerothermochemistry

    OpenAIRE

    Haider, F.; Bertier, N.; Courbet, B.; Vuillot, F.; Croisille, J.P.

    2015-01-01

    This paper presents a high order finite volume scheme built on a new k-exact reconstruction algorithm for general unstructured grids. The algorithm is capable of computing accurate polynomial approximations using data from adjacent cells only, overcoming a major obstacle to extend classical finite volume schemes beyond 2 nd order spatial accuracy. Moreover, it can easily be integrated in a cell or vertex centered finite volume method that uses the cell averages as the only unknown per grid ce...

  15. Energy-state formulation of lumped volume dynamic equations with application to a simplified free piston Stirling engine

    Science.gov (United States)

    Daniele, C. J.; Lorenzo, C. F.

    1979-01-01

    Lumped volume dynamic equations are derived using an energy-state formulation. This technique requires that kinetic and potential energy state functions be written for the physical system being investigated. To account for losses in the system, a Rayleigh dissipation function is also formed. Using these functions, a Lagrangian is formed and using Lagrange's equation, the equations of motion for the system are derived. The results of the application of this technique to a lumped volume are used to derive a model for the free-piston Stirling engine. The model was simplified and programmed on an analog computer. Results are given comparing the model response with experimental data.

  16. Assessment of research needs for advanced heterogeneous catalysts for energy applications. Final report: Volume 1, Executive summary

    Energy Technology Data Exchange (ETDEWEB)

    Mills, G.A.

    1994-04-01

    This report assesses the direction, technical content, and priority of research needs judged to provide the best chance of yielding new and improved heterogeneous catalysts for energy-related applications over a period of 5--20 years. It addresses issues of energy conservation, alternate fuels and feedstocks, and the economics and applications that could alleviate pollution from energy processes. Recommended goals are defined in 3 major, closely linked research thrusts: catalytic science, environmental protection by catalysis, and industrial catalytic applications. This volume provides a comprehensive executive summary, including research recommendations.

  17. Hydration and blood volume effects on human thermoregulation in the heat: Space applications

    Science.gov (United States)

    Sawka, Michael N.; Gonzalez, Richard R.; Pandolf, Kent B.

    1994-01-01

    Astronauts exposed to prolonged weightlessness will experience deconditioning, dehydration, and hypovolemia which all adversely affect thermoregulation. These thermoregulatory problems can be minimized by several countermeasures that manipulate body water and vascular volumes. USARIEM scientists have extensively studied dehydration effects and several possible countermeasures including hyperhydration, plasma and erythrocyte volume expansion. This paper reviews USARIEM research into these areas.

  18. Applications of Hubble Volume in Atomic Physics, Nuclear Physics, Particle Physics, Quantum Physics and Cosmic Physics

    Directory of Open Access Journals (Sweden)

    U. V. S. Seshavatharam

    2013-08-01

    Full Text Available In this paper an attempt is made to emphasize the major shortcomings of standard cosmology. It can be suggested that, the current cosmological changes can be understood by studying the atom and the atomic nucleus through ground based experiments. If light is coming from the atoms of the gigantic galaxy, then redshift can be interpreted as an index of the galactic atomic ‘light emission mechanism’. In no way it seems to be connected with ‘galaxy receding’. With ‘cosmological increasing (emitted photon energy’, observed cosmic redshift can be considered as a measure of the age difference between our galaxy and any observed galaxy. If it is possible to show that, (from the observer older galaxy’s distance increases with its ‘age’, then ‘galaxy receding’ and ‘accelerating universe’ concepts can be put for a revision at fundamental level. At any given cosmic time, the product of ‘critical density’ and ‘Hubble volume’ gives a characteristic cosmic mass and it can be called as the ‘Hubble mass’. Interesting thing is that, Schwarzschild radius of the ‘Hubble mass’ again matches with the ‘Hubble length’. Most of the cosmologists believe that this is merely a coincidence. At any given cosmic time,’Hubble length’ can be considered as the gravitational or electromagnetic interaction range. If one is willing to think in this direction, by increasing the number of applications of Hubble mass and Hubble volume in other areas of fundamental physics like quantum physics, nuclear physics, atomic physics and particle physics - slowly and gradually - in a progressive way, concepts of ‘Black hole Cosmology’ can be strengthened and can also be confirmed.

  19. Bystander Exposure to Ultra-Low-Volume Insecticide Applications Used for Adult Mosquito Management

    Directory of Open Access Journals (Sweden)

    Robert K.D. Peterson

    2011-06-01

    Full Text Available A popular and effective management option for adult mosquitoes is the use of insecticides applied by ultra-low-volume (ULV equipment. However, there is a paucity of data on human dermal exposure to insecticides applied by this method. The objective of the current study was to estimate dermal exposures to the insecticide active ingredient permethrin using water- (Aqua-Reslin® and oil-based (Permanone® 30-30 formulations with passive dosimetry. No significant differences in deposition of permethrin were observed between years, distance from the spray source, front or back of the body, or the placement of the patches on the body. However, exposure to Aqua-Reslin was significantly greater than Permanone 30-30 and average concentrations deposited on the body were 4.2 and 2.1 ng/cm2, respectively. The greater deposition of Aqua-Reslin is most likely due to the higher density of the water-based formulation which causes it to settle out faster than the lighter oil-based formulation of Permanone 30-30. The estimated average absorbed dermal exposure for permethrin from Aqua-Reslin and Permanone 30-30 was 0.00009 and 0.00005 mg/kg body weight, respectively. We also found that ground deposition of ULV insecticides can be used as a surrogate for estimating dermal exposure. The estimated exposures support the findings of previous risk assessments that exposure to ULV applications used for mosquito management are below regulatory levels of concern.

  20. Sampling based motion planning with reachable volumes: Application to manipulators and closed chain systems

    KAUST Repository

    McMahon, Troy

    2014-09-01

    © 2014 IEEE. Reachable volumes are a geometric representation of the regions the joints of a robot can reach. They can be used to generate constraint satisfying samples for problems including complicated linkage robots (e.g. closed chains and graspers). They can also be used to assist robot operators and to help in robot design.We show that reachable volumes have an O(1) complexity in unconstrained problems as well as in many constrained problems. We also show that reachable volumes can be computed in linear time and that reachable volume samples can be generated in linear time in problems without constraints. We experimentally validate reachable volume sampling, both with and without constraints on end effectors and/or internal joints. We show that reachable volume samples are less likely to be invalid due to self-collisions, making reachable volume sampling significantly more efficient for higher dimensional problems. We also show that these samples are easier to connect than others, resulting in better connected roadmaps. We demonstrate that our method can be applied to 262-dof, multi-loop, and tree-like linkages including combinations of planar, prismatic and spherical joints. In contrast, existing methods either cannot be used for these problems or do not produce good quality solutions.

  1. Feasibility of consistently estimating timber volume through landsat-based remote sensing applications

    Science.gov (United States)

    Arroyo, Renaldo Josue Salazar

    The Mississippi Institute for Forest Inventory (MIFI) is the only cost-effective large-scale forest inventory system in the United States with sufficient precision for producing reliable volume/weight/biomass estimates for small working circle areas (procurement areas). When forest industry is recruited to Mississippi, proposed working circles may overlap existing boundaries of bordering states leaving a gap of inventory information, and a remote sensing-based system for augmenting missing ground inventory data is desirable. The feasibility of obtaining acceptable cubic foot volume estimates from a Landsat-derived volume estimation model (Wilkinson 2011) was assessed by: 1) an initial study to temporally validate Landsat-derived cubic foot volume outside bark to a pulpwood top estimates in comparison with MIFI ground truth inventory plot estimates at two separate time periods, and 2) re-developing a regression model based on remotely sensed imagery in combination with available MIFI plot data. Initial results failed to confirm the relationships shown in past research between radiance values and volume estimation. The complete lack of influence of radiance values in the model led to a re-assessment of volume estimation schemes. Data outlier trimming manipulation was discovered to lead to false relationships with radiance values reported in past research. Two revised volume estimation models using age, average stand height, and trees per-acre and age and height alone as independent variables were found sufficient to explain variation of volume across the image. These results were used to develop a procedure for other remote sensing technologies that could produce data with sufficient precision for volume estimation where inventory data are sparse or non-existent.

  2. A simple method for the production of large volume 3D macroporous hydrogels for advanced biotechnological, medical and environmental applications

    Science.gov (United States)

    Savina, Irina N.; Ingavle, Ganesh C.; Cundy, Andrew B.; Mikhalovsky, Sergey V.

    2016-02-01

    The development of bulk, three-dimensional (3D), macroporous polymers with high permeability, large surface area and large volume is highly desirable for a range of applications in the biomedical, biotechnological and environmental areas. The experimental techniques currently used are limited to the production of small size and volume cryogel material. In this work we propose a novel, versatile, simple and reproducible method for the synthesis of large volume porous polymer hydrogels by cryogelation. By controlling the freezing process of the reagent/polymer solution, large-scale 3D macroporous gels with wide interconnected pores (up to 200 μm in diameter) and large accessible surface area have been synthesized. For the first time, macroporous gels (of up to 400 ml bulk volume) with controlled porous structure were manufactured, with potential for scale up to much larger gel dimensions. This method can be used for production of novel 3D multi-component macroporous composite materials with a uniform distribution of embedded particles. The proposed method provides better control of freezing conditions and thus overcomes existing drawbacks limiting production of large gel-based devices and matrices. The proposed method could serve as a new design concept for functional 3D macroporous gels and composites preparation for biomedical, biotechnological and environmental applications.

  3. High order discontinuous finite-volume/finite-element method for CFD applications

    OpenAIRE

    Ramezani A; Stipcich G.

    2014-01-01

    The proposed method naturally merges the desirable conservative properties and intuitive physical formulation of the widely used finite-volume (FV) technique, with the capability of local arbitrary high-order accuracy and high-resolution which is distinctive in the discontinuous finite-element (FE) framework. This relatively novel scheme, the discontinuous hybrid control-volume/finite-element method (DCVFEM), has been already applied to the solution of advection-diffusion problems and shallow...

  4. Application of Minimum Effective Cuff Inflating Volume for Laryngeal Mask Airway and its Impact on Postoperative Pharyngeal Complications

    Institute of Scientific and Technical Information of China (English)

    Bing-Bing Li; Jie Yan; Hong-Gang Zhou; Jing Hao; Ai-Jia Liu; Zheng-Liang Ma

    2015-01-01

    Background:High intracuffpressure can cause severe pharyngeal complications including sore throat or hoarseness after laryngeal mask airway (LMA) removal postoperatively.Though the application of minimum effective cuffinflating volume is suggested to maintain airway sealing and adequacy of ventilation for patients receiving general anesthesia with LMA at lower level of the intracuffpressure,it is currently not a standard care in most of the anesthetic departments.In this study,the minimum effective cuff inflating volume was determined for classic LMA Well LeadTM (Well Lead Medical Co.,Ltd.,China) and its impact on postoperative pharyngeal complications was also explored.Methods:Patients with American Society of Anesthesiologists physical status (Ⅰ-Ⅲ) undergoing the short-duration urological surgery were recruited in this trial.First,the minimum effective cuff inflating volume was determined for size 4 or 5 LMA Well LeadTM in the study 1.Immediately following placement and confirmation of ideal LMA position,the cuff was inflated with 5,7,10 ml of air and up to 30 ml at 5 ml increment.The intracuff pressure,oropharyngeal leak pressure (OLP),and inspiratory peak airway pressure under positive pressure ventilation at the corresponding cuff volume as indicated above were recorded.Second,the enrolled patients were randomly allocated into minimum effective cuff inflating volume group (MC) and routine care (RC) group in the study 2.The minimum effective cuff inflating volume was applied and maintained in MC group,whereas the cuff volume was inflated with half of the maximum cuff inflating volume recommended by manufacturer in RC group throughout the surgical procedure and stay in postanesthesia care unit prior to LMA removal.The incidence of pharyngeal complications at 0,2,24,and 48 h after removal of LMA and other intra-operative adverse events were also documented.Results:The intracuffpressure varied with the cuff inflating volume in a positive linear correlation

  5. Volume measurement by using super-resolution MRI: application to prostate volumetry

    CERN Document Server

    Oubel, Estanislao; Iannessi, Antoine

    2015-01-01

    Accuracy and precision of measurements are important for patient follow up in oncology but, unfortunately, partial volume effects introduce an undesired variability between observers. Super resolution techniques (SR) combine multiple acquisitions of an object into a single image richer in details. Herein, the use of SR for reducing variability is investigated in the specific context of prostate measurements. Prostate is typically imaged by T2-weighted MRI in three perpendicular low resolution images, each of them presenting partial volume effects in the direction of the slice selection gradient. SR techniques allow to combine these images into an image presenting the same level of details in all directions. This is expected to increase the accuracy and reproducibility of volume measurements, which in turn improves other derived measurements like PSA density.

  6. Volume fraction dependent magnetic behaviour of ferrofluids for rotating seal applications

    Science.gov (United States)

    Schinteie, G.; Palade, P.; Vekas, L.; Iacob, N.; Bartha, C.; Kuncser, V.

    2013-10-01

    Ferrofluid samples consisting of magnetite nanoparticles (NPs) coated with oleic acid and dispersed in a non-polar organic solvent have been synthesized by chemical routes. Different volume fractions, φ, of magnetic NPs were considered. The overall structural characterization of NPs has been performed by x-ray diffractometry, with lattice parameters and average coherence lengths evaluated via Rietveld refinements. The magnetic properties of different samples have been analysed by SQUID magnetometry and temperature-dependent Mössbauer spectroscopy and finally explained by adequate magnetic relaxation mechanisms. Zero field cooling-field cooling protocols provided useful information about specific volume fraction dependent magnetic relaxation and de-freezing processes, the lack of the Verwey transition and stronger dipolar interactions at higher volume fractions. Anisotropy energies as obtained by both temperature dependent Mössbauer spectroscopy and magnetometry data are compared and a new procedure for a quantitative characterization of the dipolar interactions is proposed.

  7. Derivation of Plastic Work Rate Done per Unit Volume for Mean Yield Criterion and Its Application

    Institute of Scientific and Technical Information of China (English)

    Dewen ZHAO; Yingjie XIE; Xiaowen WANG; Xianghua LIU

    2005-01-01

    In Haigh Westergaard stress space linear combination of twin shear stress and Tresca yield functions is called the mean yield (MY) criterion. The mathematical relationship of the criterion and its plastic work rate done per unit volume were derived. A generalized worked example of slab forging was analyzed by the criterion and its corresponding plastic work rate done per unit volume. Then, the precision of the solution was compared with those by Mises and Twin shear stress yield criterions, respectively. It turned out that the calculated results by MY criterion were in good agreement with those by Mises criterion.

  8. Viability Assessment of a Repository at Yucca Mountain. Volume 4: License Application Plan and Costs

    Energy Technology Data Exchange (ETDEWEB)

    None

    1998-12-01

    Volume 4 provides the DOE plan and cost estimate for the remaining work necessary to proceed from completing this VA to submitting an LA to NRC. This work includes preparing an EIS and evaluating the suitability of the site. Both items are necessary components of the documentation required to support a decision in 2001 by the Secretary of Energy on whether or not to recommend that the President approve the site for development as a repository. If the President recommends the site to Congress and the site designation becomes effective, then DOE will submit the LA to NRC in 2002 for authorization to construct the repository. The work described in Volume 4 constitutes the last step in the characterization of the Yucca Mountain site and the design and evaluation of the performance of a repository system in the geologic setting of this site. The plans in this volume for the next 4 years' work are based on the results of the previous 15 years' work, as reported in Volumes 1, 2, and 3 of this VA. Volume 1 summarizes what DOE has learned to date about the Yucca Mountain site. Volume 2 describes the current, reference repository design, several design options that might enhance the performance of the reference design, and several alternative designs that represent substantial departures from the reference design. Volume 2 also summarizes the results of tests of candidate materials for waste packages and for support of the tunnels into which waste would be emplaced. Volume 3 provides the results of the latest performance assessments undertaken to evaluate the performance of the design in the geologic setting of Yucca Mountain. The results described in Volumes 1, 2, and 3 provide the basis for identifying and prioritizing the work described in this volume. DOE believes that the planned work, together with the results of previous work, will be sufficient to support a site suitability evaluation for site recommendation and, if the site is recommended and designated, a

  9. Automated cerebellar segmentation: Validation and application to detect smaller volumes in children prenatally exposed to alcohol

    Directory of Open Access Journals (Sweden)

    Valerie A. Cardenas

    2014-01-01

    Discussion: These results demonstrate excellent reliability and validity of automated cerebellar volume and mid-sagittal area measurements, compared to manual measurements. These data also illustrate that this new technology for automatically delineating the cerebellum leads to conclusions regarding the effects of prenatal alcohol exposure on the cerebellum consistent with prior studies that used labor intensive manual delineation, even with a very small sample.

  10. DEVELOPMENT AND APPLICATION OF A WATER SUPPLY FINANCIAL REPORTING SYSTEM. VOLUME 1

    Science.gov (United States)

    This two-volume report describes the development of a computerized financial reporting system (FRS) for the Kenton County, Kentucky, Water District No. 1 (KCWD). The system was designed and implemented after a computer based cost analysis system (CAS) had proved to be advantageou...

  11. DEVELOPMENT AND APPLICATION OF A WATER SUPPLY FINANCIAL REPORTING SYSTEM. VOLUME 2

    Science.gov (United States)

    This two-volume report describes the development of a computerized financial reporting system (FRS) for the Kenton County, Kentucky, Water District No. 1 (KCWD). The system was designed and implemented after a computer based cost analysis system (CAS) had proved to be advantageou...

  12. Licensing an assured isolation facility for low-level radioactive waste. Volume 2: Recommendations on the content and review of an application

    Energy Technology Data Exchange (ETDEWEB)

    Silverman, D.J.; Bauser, M.A. [Morgan, Lewis and Bockius, Washington, DC (United States); Baird, R.D. [Rogers and Associates Engineering Corp., Salt Lake City, UT (United States)

    1998-07-01

    This report provides a detailed set of proposed criteria and guidance for the preparation of a license application for an assured isolation facility (AIF). The report is intended to provide a detailed planning basis upon which a prospective applicant may begin pre-licensing discussions with the Nuclear Regulatory Commission and initiate development of a license application. The report may also be useful to the NRC or to state regulatory agencies that may be asked to review such an application. Volume 1 of this report provides background information, and describes the licensing approach and methodology. Volume 2 identifies specific information that is recommended for inclusion in a license application.

  13. Licensing an assured isolation facility for low-level radioactive waste. Volume 2: Recommendations on the content and review of an application

    International Nuclear Information System (INIS)

    This report provides a detailed set of proposed criteria and guidance for the preparation of a license application for an assured isolation facility (AIF). The report is intended to provide a detailed planning basis upon which a prospective applicant may begin pre-licensing discussions with the Nuclear Regulatory Commission and initiate development of a license application. The report may also be useful to the NRC or to state regulatory agencies that may be asked to review such an application. Volume 1 of this report provides background information, and describes the licensing approach and methodology. Volume 2 identifies specific information that is recommended for inclusion in a license application

  14. A sixth-order finite volume method for the 1D biharmonic operator: Application to intramedullary nail simulation

    Directory of Open Access Journals (Sweden)

    Costa Ricardo

    2015-09-01

    Full Text Available A new very high-order finite volume method to solve problems with harmonic and biharmonic operators for onedimensional geometries is proposed. The main ingredient is polynomial reconstruction based on local interpolations of mean values providing accurate approximations of the solution up to the sixth-order accuracy. First developed with the harmonic operator, an extension for the biharmonic operator is obtained, which allows designing a very high-order finite volume scheme where the solution is obtained by solving a matrix-free problem. An application in elasticity coupling the two operators is presented. We consider a beam subject to a combination of tensile and bending loads, where the main goal is the stress critical point determination for an intramedullary nail.

  15. Aperture size to therapeutic volume relation for a multielement ultrasound system: determination of applicator adequacy for superficial hyperthermia.

    Science.gov (United States)

    Moros, E G; Myerson, R J; Straube, W L

    1993-01-01

    Three-dimensional acoustic and thermal models were developed to simulate superficial hyperthermia treatments using a new multielement planar ultrasonic system. Typical power density and steady-state temperature distributions are presented. A parametric study was performed to determine the relationship between therapeutic volume (volume at and above 42 degrees C) and aperture size (number of active elements). The parameters investigated were: maximum allowable temperature, skin surface temperature, blood perfusion (thermal diffusion length), acoustic absorption, and frequency. Results showed that this device produces well distributed sound beams with lateral dimensions comparable to the aperture size. These simulated results were in agreement with experimental measurements. The simulated temperature distributions were uniform at each depth across the applicator's aperture. The main heating characteristics found were: (1) the therapeutic volume was directly proportional to the aperture size; (2) the lateral dimensions of the therapeutic volume were independent of the parameters studied and remained practically constant with depth for several centimeters, with a very rapid increase near the skin surface and a very rapid fall off at depth; and (3) therapeutic penetration was strongly dependent on maximum allowable temperature, frequency, and acoustic absorption; and weakly dependent on blood perfusion and skin surface temperature. These heating characteristics are new in commercial systems for superficial hyperthermia. Despite the well-distributed beams, it was found that in order to produce adequate hyperthermia with this device the lateral dimensions of tumors must be smaller than the applicator's active aperture and that thermal depth coverage must be monitored during treatments. Guidelines for aperture selection and thermometry strategies are discussed. PMID:8289722

  16. Radioactive waste package assay facility. Volume 1. Application of assay technology

    International Nuclear Information System (INIS)

    This report, in three volumes, covers the work carried out by Taylor Woodrow Construction Ltd., and two major sub-contractors: Harwell Laboratory (AEA Technology) and Siemens Plessey Controls Ltd., on the development of a radioactive waste package assay facility, for cemented 500 litre intermediate level waste drums. In volume 1, the reasons for assay are considered together with the various techniques that can be used, and the information that can be obtained. The practical problems associated with the use of the various techniques in an integrated assay facility are identified, and the key parameters defined. Engineering and operational features are examined and provisional designs proposed for facilities at three throughput levels: 15,000, 750 and 30 drums per year respectively. The capital and operating costs for such facilities have been estimated. A number of recommendations are made for further work. 16 refs., 14 figs., 13 tabs

  17. Deduction of plastic work rate per unit volume for unified yield criterion and its application

    Institute of Scientific and Technical Information of China (English)

    ZHAO De-wen; LI Jing; LIU Xiang-hua; WANG Guo-dong

    2009-01-01

    A unified linear expression of plastic work rate per unit volume is deduced from the unified linear yield criterion and the associated flow rule. The expression is suitable for various linear yield loci in the error triangle between Tresca's and twin shear stress yield loci on the π-plane. It exhibits generalization in which the different value of criterion parameter b corresponds to a specific linear formula of plastic work rate per unit volume. Finally, with the unified linear expression of plastic work rate and upper-bound parallel velocity field the strip forging without bulge is successfully analyzed and an analytical result is also obtained. The comparison with traditional solutions shows that when b=1/(1+(√3)) the result is the same as the upper bound result by Mises' yield criterion, and it also is identical to that by slab method with m=1, σ0=0.

  18. Application of the control volume mixed finite element method to a triangular discretization

    Science.gov (United States)

    Naff, R.L.

    2012-01-01

    A two-dimensional control volume mixed finite element method is applied to the elliptic equation. Discretization of the computational domain is based in triangular elements. Shape functions and test functions are formulated on the basis of an equilateral reference triangle with unit edges. A pressure support based on the linear interpolation of elemental edge pressures is used in this formulation. Comparisons are made between results from the standard mixed finite element method and this control volume mixed finite element method. Published 2011. This article is a US Government work and is in the public domain in the USA. ?? 2012 John Wiley & Sons, Ltd. This article is a US Government work and is in the public domain in the USA.

  19. Study of relationship between volume of distribution and body weight application to amikacin.

    Science.gov (United States)

    Rughoo, L; Bourguignon, L; Maire, P; Ducher, M

    2014-06-01

    Amikacin use is difficult because of its narrow therapeutic and its pharmacokinetic variability. This variability of amikacin is not well known. To adapt amikacin the physician assumes that there is a linear and continuous relation between the volume of distribution and the body weight. The objective of our study was to evaluate the relationship between the volume of distribution (Vd) and the body weight (BW) using a non parametric statistical analysis of dependence so called Z method. Retrospective pharmacokinetic population study and statistic analysis. 872 patients receiving intravenous amikacin. The volume of distribution was modelled using the Non Parametric Adaptive Grid algorithm (NPAG) for a two-compartment model with intravenous infusion. Z coefficient was performed to evaluate the relationships between Vd and BW. For the 872 patients (mean age of 73 ± 17 years) dispatched as follow 53 % female and 47 % male, the analysis of the statistical relationships by the non parametric Z analysis showed a scattered linkage between Vd and BW. For the whole population, the relationship between Vd and BW was not linear (regression analysis). Z analysis demonstrated that only for 80 % of patients there is a relationship between Vd and BW. For these patients, regression analysis give a significant adjustment of a linear model (r = 0.47, p < 0.001). In the whole studied population there is not a continuous and linear relationship between Vd estimated by NPAG and the BW. These results underline the difficulties to adapt doses of amikacin with only BW information.

  20. Application analysis of solar total energy systems to the residential sector. Volume II, energy requirements. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1979-07-01

    This project analyzed the application of solar total energy systems to appropriate segments of the residential sector and determined their market penetration potential. This volume covers the work done on energy requirements definition and includes the following: (1) identification of the single-family and multi-family market segments; (2) regionalization of the United States; (3) electrical and thermal load requirements, including time-dependent profiles; (4) effect of conservation measures on energy requirements; and (5) verification of simulated load data with real data.

  1. Tri-color composite volume H-PDLC grating and its application to 3D color autostereoscopic display.

    Science.gov (United States)

    Wang, Kangni; Zheng, Jihong; Gao, Hui; Lu, Feiyue; Sun, Lijia; Yin, Stuart; Zhuang, Songlin

    2015-11-30

    A tri-color composite volume holographic polymer dispersed liquid crystal (H-PDLC) grating and its application to 3-dimensional (3D) color autostereoscopic display are reported in this paper. The composite volume H-PDLC grating consists of three different period volume H-PDLC sub-gratings. The longer period diffracts red light, the medium period diffracts the green light, and the shorter period diffracts the blue light. To record three different period gratings simultaneously, two photoinitiators are employed. The first initiator consists of methylene blue and p-toluenesulfonic acid and the second initiator is composed of Rose Bengal and N-phenyglycine. In this case, the holographic recording medium is sensitive to entire visible wavelengths, including red, green, and blue so that the tri-color composite grating can be written simultaneously by harnessing three different color laser beams. In the experiment, the red beam comes from a He-Ne laser with an output wavelength of 632.8 nm, the green beam comes from a Verdi solid state laser with an output wavelength of 532 nm, and the blue beam comes from a He-Cd laser with an output wavelength of 441.6 nm. The experimental results show that diffraction efficiencies corresponding to red, green, and blue colors are 57%, 75% and 33%, respectively. Although this diffraction efficiency is not perfect, it is high enough to demonstrate the effect of 3D color autostereoscopic display. PMID:26698768

  2. Design and Evaluation of an Intelligent Remote Tidal Volume Variability Monitoring System in E-Health Applications.

    Science.gov (United States)

    Fekr, Atena Roshan; Radecka, Katarzyna; Zilic, Zeljko

    2015-09-01

    A reliable long-term monitoring and diagnosis of breath disorders at an early stage provides an improvement of medical act, life expectancy, and quality of life while decreasing the costs of treatment and medical services. Therefore, a real-time unobtrusive monitoring of respiration patterns, as well as breath parameters, is a critical need in medical applications. In this paper, we propose an intelligent system for patient home care, capable of measuring respiration rate and tidal volume variability via a wearable sensing technology. The proposed system is designed particularly for the goal of diagnosis and treatment in patients with pathological breathing, e.g., respiratory complications after surgery or sleep disorders. The complete system was comprised of wearable calibrated accelerometer sensor, Bluetooth low energy, and cloud database. The experiments are conducted with eight subjects and the overall error in respiration rate calculation is obtained 0.29%±0.33% considering SPR-BTA spirometer as the reference. We also introduce a method for tidal volume variability estimation while validated using Pearson correlation. Furthermore, since it is essential to detect the critical events resulted from sudden rise or fall in per breath tidal volume of the patients, we provide a technique to automatically find the accurate threshold values based on each individual breath characteristics. Therefore, the system is able to detect the major changes, precisely by more than 98%, and provide immediate feedback such as sound alarm for round-the-clock respiration monitoring. PMID:26087508

  3. Application of the finite volume method to the radial conduction model of the CATHENA code

    International Nuclear Information System (INIS)

    The CATHENA code uses the finite element method (FEM) for the one-dimensional heat conduction model, which determines the temperature distribution from the fuel center to the cladding in the radial direction. However, it is shown that the finite element solutions in the heat source region such as a fuel pellet are converged to exact solutions with an increasing number of the mesh elements. Since the finite volume method (FVM) ensures local and global energy conservation due to an integral conservation over each control volume, the FVM is applied to the CATHENA wall conduction model to avoid the mesh size effect on the fuel temperature prediction. The accuracy and validity of the finite volume model in the CATHENA code are tested against two cases, a steady state and a transient heat conduction case, for which exact solutions are available. The constant temperature on the boundary surface and a uniform internal heat generation rate are assumed for the steady state problem. In the transient heat conduction problem, a cylinder is initially at a uniform temperature and suddenly its boundary surface is subjected to convection with a constant heat transfer coefficient into an ambient at a constant temperature. The steady state solutions by the FVM model are found to give almost the same results as the analytical solutions and consistent results with varying mesh sizes, while the original CATHENA with FEM over-predicts the center temperature with larger mesh sizes. The new model also closely follows the analytic solutions of the dimensionless transient heat conduction equation for a long cylinder

  4. Volume of visual field assessed with kinetic perimetry and its application to static perimetry

    Directory of Open Access Journals (Sweden)

    Christoforidis JB

    2011-04-01

    Full Text Available John B ChristoforidisCollege of Medicine, The Ohio State University, Columbus, OH, USABackground: The purpose of this study was to quantify the volume of the kinetic visual field with a single unit that accounts for visual field area and differential luminance sensitivity.Methods: Kinetic visual field perimetry was performed with a Goldmann perimeter using I4e, I3e, I2e, and I1e targets. The visual fields of 25 normal volunteers (17 women, eight men of mean age 33.9 ± 10.1 (range 17–64 years were obtained and digitized. Isopter areas were measured with a method devised to correct cartographic distortion due to polar projection inherent in perimetry and are expressed in steradians. The third dimension of each isopter represents sensitivity to target luminance and was calculated as log (target luminance-1. If luminance is expressed in cd/m2, the values for the third dimension are 0.5 for I4e, 1.0 for I3e, 1.5 for I2e, and 2.0 for I1e. The resulting unit is a steradian (log 103 (cd/m2-1 which is referred to as a Goldmann. In addition, the visual fields of four patients with representative visual defect patterns were examined and compared with normal subjects.Results: Mean isopter areas for normal subjects were 3.092 ± 0.242 steradians for I4e, 2.349 ± 0.280 steradians for I3e, 1.242 ± 0.263 steradians for I2e, and 0.251 ± 0.114 steradians for the I1e target. Isopter volumes were 1.546 ± 0.121 Goldmanns for the I4e target, 1.174 ± 0.140 Goldmanns for I3e, 0.621 ± 0.131 Goldmanns for I2e, and 0.126 ± 0.057 Goldmanns for I1e. The total mean visual field volume in our study for the I target was 3.467 ± 0.371 Goldmanns.Conclusion: The volume of the island of vision may be used to quantify a visual field with a single value which contains information about both visual field extension and differential luminance sensitivity. This technique may be used to assess the progression or stability of visual field defects over time. A similar method may

  5. ON THE FINITE VOLUME ELEMENT VERSION OF RITZ-VOLTERRA PROJECTION AND APPLICATIONS TO RELATED EQUATIONS

    Institute of Scientific and Technical Information of China (English)

    Tie Zhang; Yan-ping Lin; Robert J.Tait

    2002-01-01

    In this paper, we present a general error analysis framework for the finite volume element (FVE) approximation to the Ritz-Volterra projection, the Sobolev equations and parabolic integro-differential equations. The main idea in our paper is to consider the FVE methods as perturbations of standard finite element methods which enables us to derive the optimal L2 and H1 norm error estimates, and the L∞ and W1∞ norm error estimates by means of the time dependent Green functions. Our disc ussions also include elliptic and parabolic problems as the special cases.

  6. [Application possibilities and initial experience with digital volume tomography in hand and wrist imaging].

    Science.gov (United States)

    Goerke, Sebastian M; Neubauer, J; Zajonc, H; Thiele, J R; Kotter, E; Langer, M; Stark, G B; Lampert, F M

    2015-02-01

    During the last decade, DVT (digital volume tomography) imaging has become a widely used standard technique in head and neck imaging. Lower radiation exposure compared to conventional computed tomography (MDCT) has been described. Recently, DVT has been developed as an extremity scanner and as such represents a new imaging technique for hand surgery. We here describe the first 24 months experience with this new imaging modality in hand and wrist imaging by presenting representative cases and by describing the technical background. Furthermore, the method's advantages and disadvantages are discussed with reference to the given literature. PMID:25706176

  7. A Study on the Evaluation of Field Application of High-Fluidity Concrete Containing High Volume Fly Ash

    Directory of Open Access Journals (Sweden)

    Yun-Wang Choi

    2015-01-01

    Full Text Available In the recent concrete industry, high-fluidity concrete is being widely used for the pouring of dense reinforced concrete. Normally, in the case of high-fluidity concrete, it includes high binder contents, so it is necessary to replace part of the cement through admixtures such as fly ash to procure economic feasibility and durability. This study shows the mechanical properties and field applicability of high-fluidity concrete using mass of fly ash as alternative materials of cement. The high-fluidity concrete mixed with 50% fly ash was measured to manufacture concrete that applies low water/binder ratio to measure the mechanical characteristics as compressive strength and elastic modulus. Also, in order to evaluate the field applicability, high-fluidity concrete containing high volume fly ash was evaluated for fluidity, compressive strength, heat of hydration, and drying shrinkage of concrete.

  8. First-trimester assessment of the fetal palate: a novel application of the Volume NT algorithm.

    Science.gov (United States)

    Sepulveda, Waldo; Cafici, Daniel; Bartholomew, Julie; Wong, Amy E; Martinez-Ten, Pilar

    2012-09-01

    We describe a new technique that can facilitate the first-trimester examination of the fetal palate using the Volume NT algorithm (Samsung Medison, Seoul, Korea), a program that automatically detects the exact midsagittal plane of the head and is primarily designed for semiautomatic measurement of the nuchal translucency thickness. Three-dimensional (3D) data sets from the fetal face were captured with Volume NT and subsequently reformatted with the Oblique View software to obtain orthogonal views of the primary and secondary palate in coronal and axial planes, respectively. By testing this method in selected 3D data sets obtained retrospectively (n = 12) and prospectively (n = 28), we were able to extract clinically acceptable views of the fetal palate in all cases. This preliminary report shows that with this new 3D automation development, early evaluation of the fetal palate is feasible and reproducible and could be easily incorporated into the first-trimester sonographic protocol once its ability to detect abnormal cases is demonstrated. PMID:22922625

  9. Diffusion on a curved surface coupled to diffusion in the volume: Application to cell biology

    Science.gov (United States)

    Novak, Igor L.; Gao, Fei; Choi, Yung-Sze; Resasco, Diana; Schaff, James C.; Slepchenko, Boris M.

    2007-10-01

    An algorithm is presented for solving a diffusion equation on a curved surface coupled to diffusion in the volume, a problem often arising in cell biology. It applies to pixilated surfaces obtained from experimental images and performs at low computational cost. In the method, the Laplace-Beltrami operator is approximated locally by the Laplacian on the tangential plane and then a finite volume discretization scheme based on a Voronoi decomposition is applied. Convergence studies show that mass conservation built in the discretization scheme and cancellation of sampling error ensure convergence of the solution in space with an order between 1 and 2. The method is applied to a cell-biological problem where a signaling molecule, G-protein Rac, cycles between the cytoplasm and cell membrane thus coupling its diffusion in the membrane to that in the cell interior. Simulations on realistic cell geometry are performed to validate, and determine the accuracy of, a recently proposed simplified quantitative analysis of fluorescence loss in photobleaching. The method is implemented within the Virtual Cell computational framework freely accessible at http://www.vcell.org.

  10. Development of a multicomponent force and moment balance for water tunnel applications, volume 1

    Science.gov (United States)

    Suarez, Carlos J.; Malcolm, Gerald N.; Kramer, Brian R.; Smith, Brooke C.; Ayers, Bert F.

    1994-12-01

    The principal objective of this research effort was to develop a multicomponent strain gauge balance to measure forces and moments on models tested in flow visualization water tunnels. An internal balance was designed that allows measuring normal and side forces, and pitching, yawing and rolling moments (no axial force). The five-components to applied loads, low interactions between the sections and no hysteresis. Static experiments (which are discussed in this Volume) were conducted in the Eidetics water tunnel with delta wings and a model of the F/A-18. Experiments with the F/A-18 model included a thorough baseline study and investigations of the effect of control surface deflections and of several Forebody Vortex Control (FVC) techniques. Results were compared to wind tunnel data and, in general, the agreement is very satisfactory. The results of the static tests provide confidence that loads can be measured accurately in the water tunnel with a relatively simple multicomponent internal balance. Dynamic experiments were also performed using the balance, and the results are discussed in detail in Volume 2 of this report.

  11. Optimization of multi-grating volume holographic spectrum splitters for photovoltaic applications.

    Science.gov (United States)

    Ingersoll, G B; Leger, J R

    2016-07-10

    Recent research has shown that using multiple diverse-bandgap photovoltaic (PV) cells in conjunction with a spectrum splitting optical system can significantly improve PV power generation efficiency. Although volume Bragg gratings (VBGs) can serve as effective spectrum splitters, the inherent dispersion of a VBG can be detrimental given a broad-spectrum input. The performance of a single holographic spectrum splitter element can be improved by utilizing multiple single volume gratings, each operating in a slightly different spectral band. However, care must be taken to avoid inter-grating coupling effects that limit the ultimate performance. This work explores broadband two-grating holographic optical elements (HOEs) in multiplexed (single element) and sandwiched-grating arrangements. Particle swarm optimization is used to tailor these systems to the solar spectrum, taking into account both efficiency and dispersion. Both multiplexed and sandwiched two-grating systems exhibit performance improvements over single-grating solutions, especially when reduced dispersion is required. Under a ±2° constraint on output angular spread from wavelength dispersion, sandwiched-, multiplexed-, and single-grating systems exhibit power conversion efficiencies of 82.1%, 80.9%, and 77.5%, respectively, compared to an ideal bandpass spectrum splitter. Dispersion performance can be further improved by employing more than two VBGs in the spectrum splitter, but efficiency is compromised by additional cross-coupling effects. Multiplexed-grating systems are especially susceptible to these effects, but have the advantage of utilizing only a single HOE.

  12. Optimization of multi-grating volume holographic spectrum splitters for photovoltaic applications.

    Science.gov (United States)

    Ingersoll, G B; Leger, J R

    2016-07-10

    Recent research has shown that using multiple diverse-bandgap photovoltaic (PV) cells in conjunction with a spectrum splitting optical system can significantly improve PV power generation efficiency. Although volume Bragg gratings (VBGs) can serve as effective spectrum splitters, the inherent dispersion of a VBG can be detrimental given a broad-spectrum input. The performance of a single holographic spectrum splitter element can be improved by utilizing multiple single volume gratings, each operating in a slightly different spectral band. However, care must be taken to avoid inter-grating coupling effects that limit the ultimate performance. This work explores broadband two-grating holographic optical elements (HOEs) in multiplexed (single element) and sandwiched-grating arrangements. Particle swarm optimization is used to tailor these systems to the solar spectrum, taking into account both efficiency and dispersion. Both multiplexed and sandwiched two-grating systems exhibit performance improvements over single-grating solutions, especially when reduced dispersion is required. Under a ±2° constraint on output angular spread from wavelength dispersion, sandwiched-, multiplexed-, and single-grating systems exhibit power conversion efficiencies of 82.1%, 80.9%, and 77.5%, respectively, compared to an ideal bandpass spectrum splitter. Dispersion performance can be further improved by employing more than two VBGs in the spectrum splitter, but efficiency is compromised by additional cross-coupling effects. Multiplexed-grating systems are especially susceptible to these effects, but have the advantage of utilizing only a single HOE. PMID:27409317

  13. Soft goldstone excitations in finite volumes applications from eV to TeV physics

    International Nuclear Information System (INIS)

    Finite site soft pion theorems are reviewed with special emphasis on applications. These range from quantum models relevant for high T/sub C/ superconductivity to classical models relevant for the symmetry breaking sector of the standard model. 8 refs

  14. High-resolution dynamic angiography using flat-panel volume CT: feasibility demonstration for neuro and lower limb vascular applications

    Energy Technology Data Exchange (ETDEWEB)

    Mehndiratta, Amit [Massachusetts General Hospital, Department of Radiology, Harvard Medical School, Boston, MA (United States); University of Oxford, Institute of Biomedical Engineering and Keble College, Oxford (United Kingdom); Indian Institute of Technology Delhi and All India Institute of Medical Science, Centre for Biomedical Engineering, New Delhi (India); Rabinov, James D. [Massachusetts General Hospital, Interventional Neuroradiology, Harvard Medical School, Boston, MA (United States); Grasruck, Michael [Siemens Medical Solutions, Forchheim (Germany); Liao, Eric C. [Massachusetts General Hospital, Department of Plastic and Reconstructive Surgery and Center for Regenerative Medicine, Harvard Medical School, Boston, MA (United States); Crandell, David [Spaulding Rehabilitation Hospital, Department of Physical Medicine and Rehabilitation, Harvard Medical School, Charlestown, MA (United States); Gupta, Rajiv [Massachusetts General Hospital, Department of Radiology, Harvard Medical School, Boston, MA (United States)

    2015-07-15

    This paper evaluates a prototype flat-panel volume CT (fpVCT) for dynamic in vivo imaging in a variety of neurovascular and lower limb applications. Dynamic CTA was performed on 12 patients (neuro = 8, lower limb = 4) using an fpVCT with 120 kVp, 50 mA, rotation time varying from 8 to 19 s, and field of view of 25 x 25 x 18 cm{sup 3}. Four-dimensional data sets (i.e. 3D images over time) were reconstructed and reviewed. Dynamic CTA demonstrated sufficient spatio-temporal resolution to elucidate first-pass and recirculation dynamics of contrast bolus through neurovasclar pathologies and phasic blood flow though lower-limb vasculature and grafts. The high spatial resolution of fpVCT resulted in reduced partial volume and metal beam-hardening artefacts. This facilitated assessment of vascular lumen in the presence of calcified plaque and evaluation of fractures, especially in the presence of fixation hardware. Evaluation of arteriovenous malformation using dynamic fpVCT angiography was of limited utility. Dynamic CTA using fpVCT can visualize time-varying phenomena in neuro and lower limb vascular applications and has sufficient diagnostic imaging quality to evaluate a number of pathologies affecting these regions. (orig.)

  15. Photovoltaic system criteria documents. Volume 3: Environmental issues and evaluation criteria for photovoltaic applications

    Science.gov (United States)

    Koenig, John C.; Billitti, Joseph W.; Tallon, John M.

    1979-01-01

    The environmental issues and evaluation criteria relating to the suitability of sites proposed for photovoltaic (PV) system deployment are identified. The important issues are defined, briefly discussed and then developed into evaluation criteria. System designers are provided with information on the environmental sensitivity of PV systems in realistic applications, background material which indicates the applicability of the siting issues identified, and evaluation criteria are defined to facilitate the selection of sites that maximize PV system operation.

  16. Industrial applications study. Volume V. Bibliography of relevant literature. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Harry L.; Hamel, Bernard B.; Karamchetty, Som; Steigelmann, William H.; Gajanana, Birur C.; Agarwal, Anil P.; Klock, Lawrence W.; Henderson, James M.; Calobrisi, Gary; Hedman, Bruce A.; Koluch, Michael; Biancardi, Frank; Bass, Robert; Landerman, Abraham; Peters, George; Limaye, Dilip; Price, Jeffrey; Farr, Janet

    1976-12-01

    This five-volume report represents an initial Phase O evaluation of waste heat recovery and utilization potential in the manufacturing portion of the industrial sector. The scope of this initial phase was limited to the two-digit SIC level and addressed the feasibility of obtaining in-depth energy information in the industrial sector. Within this phase, a successful methodology and approaches for data gathering and assessment are established. Using these approaches, energy use and waste heat profiles were developed at the 2-digit level; with this data, waste heat utilization technologies were evaluated. The first section of the bibliography lists extensive citations for all industries. The next section is composed of an extensive literature search with abstracts for industrial energy conservation. EPA publications on specific industries and general references conclude the publication. (MCW)

  17. Microinvasion of liver metastases from colorectal cancer: predictive factors and application for determining clinical target volume

    International Nuclear Information System (INIS)

    This study evaluates the microscopic characteristics of liver metastases from colorectal cancer (LMCRC) invasion and provides a reference for expansion from gross tumor volume (GTV) to clinical targeting volume (CTV). Data from 129 LMCRC patients treated by surgical resection at our hospital between January 2008 and September 2009 were collected for study. Tissue sections used for pathology and clinical data were reviewed. Patient information used for the study included gender, age, original tumor site, number of tumors, tumor size, levels of carcinoembryonic antigen (CEA) and carbohydrate antigen 199 (CA199), synchronous or metachronous liver metastases, and whether patients received chemotherapy. The distance of liver microinvasion from the tumor boundary was measured microscopically by two senior pathologists. Of 129 patients evaluated, 81 (62.8 %) presented microinvasion distances from the tumor boundary ranging between 1.0 − 7.0 mm. A GTV-to-CTV expansion of 5, 6.7, or 7.0 mm was required to provide a 95, 99, or 100 % probability, respectively, of obtaining clear resection margins by microscopic observation. The extent of invasion was not related to gender, age, synchronous or metachronous liver metastases, tumor size, CA199 level, or chemotherapy. The extent of invasion was related to original tumor site, CEA level, and number of tumors. A scoring system was established based on the latter three positive predictors. Using this system, an invasion distance less than 3 mm was measured in 93.4 % of patients with a score of ≤1 point, but in only 85.7 % of patients with a score of ≤2 points. The extent of tumor invasion in our LMCRC patient cohort correlated with original tumor site, CEA level, and number of tumors. These positive predictors may potentially be used as a scoring system for determining GTV-to-CTV expansion

  18. Multiagent Systems and Applications Volume 2 Development Using the GORITE BDI Framework

    CERN Document Server

    Jarvis, Dennis; Ronnquist, Ralph; Jain, Lakhmi C

    2013-01-01

    Since its conception almost 30 years ago, the BDI (Belief Desire Intention) model of agency has become established, along with Soar, as the approach of choice for practitioners in the development of knowledge intensive agent applications. However, in developing BDI agent applications for over 15 years, the authors of this book have observed a disconnect between what the BDI model provides and what is actually required of an agent model in order to build practical systems. The GORITE BDI framework was  developed to address this gap and this book is written for students, researchers and practitioners who wish to gain a practical understanding of how GORITE is used to develop BDI agent applications. In this regard, a feature of the book is the use of complete, annotated examples. As GORITE is a Java framework,  a familiarity with Java (or a similar language) is assumed, but no prior knowledge of the BDI model is required.

  19. Assessment of research needs for advanced heterogeneous catalysts for energy applications. Final report: Volume 2, Topic reports

    Energy Technology Data Exchange (ETDEWEB)

    Mills, G.A.

    1994-04-01

    This report assesses the direction, technical content, and priority of research needs judged to provide the best chance of yielding new and improved heterogeneous catalysts for energy-related applications over the period of 5-20 years. It addresses issues of energy conservation, alternate fuels and feedstocks, and the economics and applications that could alleviate pollution from energy processes. Recommended goals are defined in 3 research thrusts: catalytic science, environmental protection by catalysis, and industrial catalytic applications. This study was conducted by an 11-member panel of experts from industry and academia, including one each from Japan and Europe. This volume first presents an in-depth overview of the role of catalysis in future energy technology in chapter 1; then current catalytic research is critically reviewed and research recommended in 8 topic chapters: catalyst preparation (design and synthesis), catalyst characterization (structure/function), catalyst performance testing, reaction kinetics/reactor design, catalysis for industrial chemicals, catalysis for electrical applications (clean fuels, pollution remediation), catalysis for control of exhaust emissions, and catalysts for liquid transportation fuels from petroleum, coal, residual oil, and biomass.

  20. Application of rock mechanics to cut-and-fill mining. Volume 3

    Energy Technology Data Exchange (ETDEWEB)

    1980-05-15

    The conference on application of rock mechanics to cut-and-fill mining was held June 1-3, 1980, at the University of Luleaa, Luleaa, Sweden. Basic rock mechanics investigations of interest involving improving the support characteristics of backfilling by adding cement, compacting, and water removal have been entered individually into EDB. The papers also cover measurements of the support capability of such fills and the application of deformation measurements and calculations using finite element computer codes to the mining of particular ore bodies, including changes in the calculations as the mining progressed. (LTN)

  1. Probabilistic risk assessment course documentation. Volume 2. Probability and statistics for PRA applications

    International Nuclear Information System (INIS)

    This course is intended to provide the necessary probabilistic and statistical skills to perform a PRA. Fundamental background information is reviewed, but the principal purpose is to address specific techniques used in PRAs and to illustrate them with applications. Specific examples and problems are presented for most of the topics

  2. Case-study application of venture analysis: the integrated energy utility. Volume 3. Appendices

    Energy Technology Data Exchange (ETDEWEB)

    Fein, E; Gordon, T J; King, R; Kropp, F G; Shuchman, H L; Stover, J; Hausz, W; Meyer, C

    1978-11-01

    The appendices for a case-study application of venture analysis for an integrated energy utility for commercialization are presented. The following are included and discussed: utility interviews; net social benefits - quantitative calculations; the financial analysis model; market penetration decision model; international district heating systems; political and regulatory environment; institutional impacts.

  3. Draft Title 40 CFR 191 compliance certification application for the Waste Isolation Pilot Plant. Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-31

    The Waste Isolation Pilot Plant (WIPP) is a research and development facility for the demonstration of the permanent isolation of transuranic radioactive wastes in a geologic formation. The facility was constructed in southeastern New Mexico in a manner intended to meet criteria established by the scientific and regulatory community for the safe, long-term disposal of transuranic wastes. The US Department of Energy (DOE) is preparing an application to demonstrate compliance with the requirements outlined in Title 40, Part 191 of the Code of Federal Regulations (CFR) for the permanent disposal of transuranic wastes. As mandated by the Waste Isolation Pilot Plant (WIPP) Land Withdrawal Act of 1992, the US Environmental Protection Agency (EPA) must evaluate this compliance application and provide a determination regarding compliance with the requirements within one year of receiving a complete application. Because the WIPP is a very complex program, the DOE has planned to submit the application as a draft in two parts. This strategy will allow for the DOE and the EPA to begin technical discussions on critical WIPP issues before the one-year compliance determination period begins. This report is the first of these two draft submittals.

  4. Draft Title 40 CFR 191 compliance certification application for the Waste Isolation Pilot Plant. Volume 1

    International Nuclear Information System (INIS)

    The Waste Isolation Pilot Plant (WIPP) is a research and development facility for the demonstration of the permanent isolation of transuranic radioactive wastes in a geologic formation. The facility was constructed in southeastern New Mexico in a manner intended to meet criteria established by the scientific and regulatory community for the safe, long-term disposal of transuranic wastes. The US Department of Energy (DOE) is preparing an application to demonstrate compliance with the requirements outlined in Title 40, Part 191 of the Code of Federal Regulations (CFR) for the permanent disposal of transuranic wastes. As mandated by the Waste Isolation Pilot Plant (WIPP) Land Withdrawal Act of 1992, the US Environmental Protection Agency (EPA) must evaluate this compliance application and provide a determination regarding compliance with the requirements within one year of receiving a complete application. Because the WIPP is a very complex program, the DOE has planned to submit the application as a draft in two parts. This strategy will allow for the DOE and the EPA to begin technical discussions on critical WIPP issues before the one-year compliance determination period begins. This report is the first of these two draft submittals

  5. Deposition from Ultra-Low Volume Application of Public Health Insecticides in a Hot Desert Environment.

    Science.gov (United States)

    Fisher, Michael L; Hoel, David F; Farooq, Muhammad; Walker, Todd W

    2015-06-01

    Three insecticides commonly used for mosquito and sand fly control were applied 30 min to 3 h after sunset during June and July 2010, at Camp Buehring, Kuwait, to determine the relative quantity of pesticides to height and distance traveled in a hot desert environment. A BVA dilution oil was used for the control. Oil-based adulticides were sprayed using a truck-mounted Curtis DynaFog Maxi-Pro 4 ultra-low volume (ULV) sprayer. Malathion (Fyfanon ULV, 96% active ingredient [AI]), resmethrin (Scourge 4+12, 4% AI), pyrethrins (ULD BP-300, 3% AI), and BVA Spray 13 (100% refined petroleum distillate) were mixed with Uvitex optical brightener fluorescent dye and applied at 2 speeds on evenings when wind speed was less than 16.1 km/h (10 mph). Collection targets using biodegradable cotton ribbons (1 m×2.5 cm) were later read with a fluorometer to quantify the amount of insecticide deposited on targets set at heights of 15.2, 76.2, and 152.4 cm (6, 30, and 60 in.) and distances of 1.5, 6.1, 15.2, 30.5, 61.0, and 91.4 m (5, 20, 50, 100, 200, and 300 ft). Mean insecticide deposition across all distances was 31% on 76.2-cm targets and 49% on 152.4-cm targets, while 15.2-cm targets typically collected Middle East. PMID:26181691

  6. Application handbook for a Standardized Control Module (SCM) for DC-DC converters, volume 1

    Science.gov (United States)

    Lee, F. C.; Mahmoud, M. F.; Yu, Y.

    1980-01-01

    The standardized control module (SCM) was developed for application in the buck, boost and buck/boost DC-DC converters. The SCM used multiple feedback loops to provide improved input line and output load regulation, stable feedback control system, good dynamic transient response and adaptive compensation of the control loop for changes in open loop gain and output filter time constraints. The necessary modeling and analysis tools to aid the design engineer in the application of the SCM to DC-DC Converters were developed. The SCM functional block diagram and the different analysis techniques were examined. The average time domain analysis technique was chosen as the basic analytical tool. The power stage transfer functions were developed for the buck, boost and buck/boost converters. The analog signal and digital signal processor transfer functions were developed for the three DC-DC Converter types using the constant on time, constant off time and constant frequency control laws.

  7. Application of rock mechanics to cut-and-fill mining. Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    1980-05-15

    The conference on application of rock mechanics to cut-and-fill mining was held June 1-3, 1980, at the University of Luleaa, Sweden. The conference began with reviews of the application of rock mechanics to mining and back filling in Australia, Canada and the USA. More particular papers involved mines in Sweden, Italy, Australia (pre reinforcement of walls with steel cables cemented in) and at the Con Mine in Canada. Two papers involved backfill material and specifications. Eight papers involved the use of the mathematical models for calculating the stresses developed in the rock mass by computer calculations and therefore, the probable stability. Such calculations are particularly necessary in deep mines. Papers of general interest were entered individually into EDB. (LTN)

  8. Evaluation of the Trajectory Operations Applications Software Task (TOAST). Volume 2: Interview transcripts

    Science.gov (United States)

    Perkins, Sharon; Martin, Andrea; Bavinger, Bill

    1990-01-01

    The Trajectory Operations Applications Software Task (TOAST) is a software development project whose purpose is to provide trajectory operation pre-mission and real-time support for the Space Shuttle. The purpose of the evaluation was to evaluate TOAST as an Application Manager - to assess current and planned capabilities, compare capabilities to commercially-available off the shelf (COTS) software, and analyze requirements of MCC and Flight Analysis Design System (FADS) for TOAST implementation. As a major part of the data gathering for the evaluation, interviews were conducted with NASA and contractor personnel. Real-time and flight design users, orbit navigation users, the TOAST developers, and management were interviewed. Code reviews and demonstrations were also held. Each of these interviews was videotaped and transcribed as appropriate. Transcripts were edited and are presented chronologically.

  9. Noninvasive Evaluation of Bladder Wall Mechanical Properties as a Function of Filling Volume: Potential Application in Bladder Compliance Assessment.

    Directory of Open Access Journals (Sweden)

    Ivan Nenadic

    Full Text Available We propose a novel method to monitor bladder wall mechanical properties as a function of filling volume, with the potential application to bladder compliance assessment. The proposed ultrasound bladder vibrometry (UBV method uses ultrasound to excite and track Lamb waves on the bladder wall from which its mechanical properties are derived by fitting measurements to an analytical model. Of particular interest is the shear modulus of bladder wall at different volumes, which we hypothesize, is similar to measuring the compliance characteristics of the bladder.Three experimental models were used: 1 an ex vivo porcine model where normal and aberrant (stiffened by formalin bladders underwent evaluation by UBV; 2 an in vivo study to evaluate the performance of UBV on patients with clinically documented compliant and noncompliant bladders undergoing UDS; and 3 a noninvasive UBV protocol to assess bladder compliance using oral hydration and fractionated voiding on three healthy volunteers.The ex vivo studies showed a high correlation between the UBV parameters and direct pressure measurement (R2 = 0.84-0.99. A similar correlation was observed for 2 patients with compliant and noncompliant bladders (R2 = 0.89-0.99 undergoing UDS detrusor pressure-volume measurements. The results of UBV on healthy volunteers, performed without catheterization, were comparable to a compliant bladder patient.The utility of UBV as a method to monitor changes in bladder wall mechanical properties is validated by the high correlation with pressure measurements in ex vivo and in vivo patient studies. High correlation UBV and UDS in vivo studies demonstrated the potential of UBV as a bladder compliance assessment tool. Results of studies on healthy volunteers with normal bladders demonstrated that UBV could be performed noninvasively. Further studies on a larger cohort are needed to fully validate the use of UBV as a clinical tool for bladder compliance assessment.

  10. CMOS detectors for space applications: from R&D to operational program with large volume foundry

    OpenAIRE

    Martin-Gonthier, Philippe; Magnan, Pierre; Corbière, Franck; Rolando, Sébastien; Saint-Pé, Olivier; Breart de Boisanger, M.; Larnaudie, Franck

    2010-01-01

    Nowadays, CMOS image sensors are widely considered for space applications. The use of CIS (CMOS Image sensor) processes has significantly enhanced their performances such as dark current, quantum efficiency and conversion gain. However, in order to fulfil specific space mission requirements, dedicated research and development work has to be performed to address specific detector performance issues. This is especially the case for dynamic range improvement through output voltage swing optim...

  11. A New DFT Architecture to Reduce Test Data Volume and Test Application Time

    OpenAIRE

    Ling, Zhang; Jishun, Kuang; Junjin, Mei

    2016-01-01

    This paper proposes a new DFT Architecture that contains three test scan modes. The test data could be interval broadcast to scan chains whenever the data in corresponding locations are compatible. Compared with the conventional broadcast scan architecture, the proposed architecture achieves better compression ratio in all cases, and the test application time is also induced. The hardware overhead is very low. Both theoretical and experimental results prove efficacy and versatility of the pro...

  12. Effectiveness of indoor ultra-low volume application of Aqua Reslin® Super during an emergency.

    Science.gov (United States)

    Ordóñez González, José Genaro; Thirion, Jaime; García Orozco, Abel; Rodríguez, Américo D

    2011-06-01

    Indoor ultra-low volume (ULV) applications of Aqua Reslin Super (Permethrin + s-bioallethrin) were carried out using portable Solo Port 423 sprayers in an urban area of Reforma, Chiapas, Mexico. Sprayers were calibrated to discharge a flow rate of 110 ml/min with a dose range of approximately 0.55 to 0.792 mg Al/m3 space. Entomological evaluation, based on 3 cages per house, each containing 15 sugar-fed, 2-4-day-old Aedes aegypti females and placed in hidden locations in 4 randomly selected houses for 15 min, showed 98.8% to 100% mortality. After the spraying, ovitrap data showed no mosquito adults present 4 days after the applications, and only 1 ovitrap out of 60 positive 8 days after the intervention. This evaluation suggests that indoor ULV application can be useful during emergencies after disasters, during dengue outbreaks, or to prevent mosquito population outbreaks before rainy seasons and, therefore, the onset of dengue transmission in Mexican dengue transmission risk areas.

  13. Assessment of solar options for small power systems applications. Volume III. Analysis of concepts

    Energy Technology Data Exchange (ETDEWEB)

    Laity, W.W.; Aase, D.T.; Apley, W.J.; Bird, S.P.; Drost, M.K.; Garrett-Price, B.A.; Williams, T.A.

    1980-09-01

    A comparative analysis of solar thermal conversion concepts that are potentially suitable for development as small electric power systems (1 to 10 MWe) is given. Seven generic types of collectors, together with associated subsystems for electric power generation, were considered. The collectors can be classified into three categories: (1) two-axis tracking (with compound-curvature reflecting surfaces; (2) one-axis tracking (with single-curvature reflecting suraces; and (3) nontracking (with low-concentration reflecting surfaces). All seven collectors were analyzed in conceptual system configurations with Rankine-cycle engines. In addition, two of the collectors (the Point Focus Central Receiver and the Point Focus Distributed Receiver) were analyzed with Brayton-cycle engines, and the latter of the two also was analyzed with Stirling-cycle engines. This volume describes the systems analyses performed on all the alternative configurations of the seven generic collector concepts and the results obtained. The SOLSTEP computer code used to determine each configuration's system cost and performance is briefly described. The collector and receiver performance calculations used are also presented. The capital investment and related costs that were obtained from the systems studies are presented, and the levelized energy costs are given as a function of capacity factor obtained from the systems studies. Included also are the values of the other attributes used in the concepts' final ranking. The comments, conclusions, and recommendations developed by the PNL study team during the concept characterization and systems analysis tasks of the study are presented. (WHK)

  14. Storm-water infiltration and focused recharge modeling with finite-volume two-dimensional Richards equation: application to an experimental rain garden

    OpenAIRE

    Aravena, Jazmín E.; Dussaillant, Alejandro

    2009-01-01

    Rain gardens are infiltration systems that provide volume and water quality control, recharge enhancement, as well as landscape, ecological, and economic benefits. A model for application to rain gardens based on Richards equation coupled to a surface water balance was developed, using a two-dimensional finite-volume code. It allows for alternating upper boundary conditions, including ponding and overflow, and can simulate heterogeneous soil-layering or more complex geometries to estimate inf...

  15. High-volume use of self-cementing spray dry absorber material for structural applications

    Science.gov (United States)

    Riley, Charles E.

    Spray dry absorber (SDA) material, or spray dryer ash, is a byproduct of energy generation by coal combustion and sulfur emissions controls. Like any resource, it ought to be used to its fullest potential offsetting as many of the negative environmental impacts of coal combustion as possible throughout its lifecycle. Its cementitious and pozzolanic properties suggest it be used to augment or replace another energy and emissions intensive product: Portland cement. There is excellent potential for spray dryer ash to be used beneficially in structural applications, which will offset CO2 emissions due to Portland cement production, divert landfill waste by further utilizing a plentiful coal combustion by-product, and create more durable and sustainable structures. The research into beneficial use applications for SDA material is relatively undeveloped and the material is highly underutilized. This dissertation explored a specific self-cementing spray dryer ash for use as a binder in structural materials. Strength and stiffness properties of hydrated spray dryer ash mortars were improved by chemical activation with Portland cement and reinforcement with polymer fibers from automobile tire recycling. Portland cement at additions of five percent of the cementitious material was found to function effectively as an activating agent for spray dryer ash and had a significant impact on the hardened properties. The recycled polymer fibers improved the ductility and toughness of the material in all cases and increased the compressive strength of weak matrix materials like the pure hydrated ash. The resulting hardened materials exhibited useful properties that were sufficient to suggest that they be used in structural applications such as concrete, masonry block, or as a hydraulic cement binder. While the long-term performance characteristics remain to be investigated, from an embodied-energy and carbon emissions standpoint the material investigated here is far superior to

  16. Water recovery and solid waste processing for aerospace and domestic applications. Volume 1: Final report

    Science.gov (United States)

    Murray, R. W.

    1973-01-01

    A comprehensive study of advanced water recovery and solid waste processing techniques employed in both aerospace and domestic or commercial applications is reported. A systems approach was used to synthesize a prototype system design of an advanced water treatment/waste processing system. Household water use characteristics were studied and modified through the use of low water use devices and a limited amount of water reuse. This modified household system was then used as a baseline system for development of several water treatment waste processing systems employing advanced techniques. A hybrid of these systems was next developed and a preliminary design was generated to define system and hardware functions.

  17. Thirteenth Workshop for Computational Fluid Dynamic Applications in Rocket Propulsion and Launch Vehicle Technology. Volume 2

    Science.gov (United States)

    Williams, R. W. (Compiler)

    1996-01-01

    This conference publication includes various abstracts and presentations given at the 13th Workshop for Computational Fluid Dynamic Applications in Rocket Propulsion and Launch Vehicle Technology held at the George C. Marshall Space Flight Center April 25-27 1995. The purpose of the workshop was to discuss experimental and computational fluid dynamic activities in rocket propulsion and launch vehicles. The workshop was an open meeting for government, industry, and academia. A broad number of topics were discussed including computational fluid dynamic methodology, liquid and solid rocket propulsion, turbomachinery, combustion, heat transfer, and grid generation.

  18. Optimal nutrient application strategy for bioremediation of oil-polluted beaches. Volume 1

    International Nuclear Information System (INIS)

    Offshore oil spills in coastal areas generally occur in the intertidal zone of beaches and affect the top 25 cm of soil, known as the bioremediation zone. Biostimulation by nutrient application such as nitrogen and phosphorus is a viable technology for restoring oil-contaminated beaches. The key for achieving a rapid cost-effective cleanup is to ensure maximum nutrient residence time. This study proposed a strategy that consisted of injecting nutrients through a perforated pipe at the high tide line. Beach hydraulics were numerically simulated to estimate the optimal injection flow rate of nutrient solution. It was shown that the optimal application should begin following high tide just as it drops and should last for half a tidal cycle. The flow rate ensures that the saturated wet-front of the nutrient solution on the beach surface moves seaward with the same speed of the falling tide keeping a constant distance with the tide line. The numerical results were generalized to a broad range of hydraulic and tidal properties of beaches using an innovative dimensionless formulation for water flow and solute transport in porous media. Nomographs were presented to provide the flow rate based on 4 parameters, notably the beach slope, permeability, tidal amplitude and tidal period. 29 refs., 1 tab., 5 figs

  19. Thermal power systems, small power systems application project. Volume 1: Executive summary

    Science.gov (United States)

    Marriott, A. T.

    1979-01-01

    Current small power system technology as applied to power plants up to 10 MWe in size was assessed. Markets for small power systems were characterized and cost goals were established. Candidate power plant system design concepts were selected for evaluation and preliminary performance and cost assessments were made. Economic studies were conducted and breakeven capital costs were determined for leading contenders among the candidate systems. An application study was made of the potential use of small power systems in providing part of the demand for pumping power by the extensive aqueduct system of California, estimated to be 1000 MWe by 1985. Criteria and methodologies were developed for application to the ranking of candidate power plant system design concepts. Experimental power plants concepts of 1 MWe rating were studied leading toward the definition of a power plant configuration for subsequent detail design, construction, testing and evaluation as Engineering Experiment No. 1 (EE No. 1). Site selection criteria and ground rules for the solicitation of EE No. 1 site participation proposals by DOE were developed.

  20. High-Volume Non-Destructive Test Applications at the Hanford Atomic Products Operation

    International Nuclear Information System (INIS)

    Safety and efficiency of critical Hanford processes are assured with rapid, reliable, and automatic non-destructive tests. High-sensitive eddy-current and ultrasonic inspection systems are in routine use in the field and in manufacturing production processes to provide maximum quality assurance of large volumes of material in minimum inspection time. This paper describes inspection systems being used to ensure quality of Hanford's production nuclear-fuel manufacturing processes. Operated as regular in-line manufacturing equipment, these systems employ ultrasonic attenuation measurements to monitor grain structure of bare uranium fuel cores, ultrasonic and eddy- current techniques to ensure adequate bonding and thickness of 0.040 in aluminium cladding on canned elements, and novel wide-band, high-resolution ultrasonic inspection techniques to detect defects in the fuel end-weld closures. Combined eddy-current and ultrasonic tests are applied simultaneously to perform a complete fuel- element inspection on a nine-second cycle; defective elements are automatically segregated from the process stream. Emphasis is given to advanced ultrasonic test methods of inspecting thin-walled, fuel-sheath tubing. Special highly focused transducers are used with wide-band circuitry to generate pure shear waves in 0.015-in-thick wall tubing. Lamb and other complicated wave motions are excluded so that tests results are readily interpreted and reproduced. Novel, economical methods of producing defect standards have been developed, as have critically important methods of ensuring uniform operating characteristics of the transducers themselves. Automatic tubing inspection equipment has been developed, and results of its routine use in testing some 30 000 ft of tubing are summarized. Finally, eddy-current techniques developed specifically for inspecting installed heat-exchanger tubing are reviewed. The technique employs novel read-out features which plot defect indications as oscilloscope

  1. Sixth Annual Workshop on Space Operations Applications and Research (SOAR 1992), volume 2

    International Nuclear Information System (INIS)

    This document contains papers presented at the Space Operations, Applications, and Research Symposium (SOAR) hosted by the U.S. Air Force (USAF) on 4-6 Aug. 1992. The symposium was cosponsored by the Air Force Material Command and by NASA/JSC. Key technical areas covered during the symposium were robotics and telepresence, automation and intelligent systems, human factors, life sciences, and space maintenance and servicing. The SOAR differed from most other conferences in that it was concerned with Government-sponsored research and development relevant to aerospace operations. Symposium proceedings include papers covering various disciplines presented by experts from NASA, the USAF, universities, and industry. Separate abstracts have been prepared for articles from this report

  2. Study of power management technology for orbital multi-100KWe applications. Volume 3: Requirements

    Science.gov (United States)

    Mildice, J. W.

    1980-01-01

    Mid to late 1980's power management technology needs to support development of a general purpose space platform, capable of suplying 100 to 250 KWe to a variety of users in low Earth orbit are examined. A typical, shuttle assembled and supplied space platform is illustred, along with a group of payloads which might reasonably be expected to use such a facility. Examination of platform and user power needs yields a set of power requirements used to evaluate power management options for life cycle cost effectivness. The most cost effective ac/dc and dc systems are evaluated, specifically to develop system details which lead to technology goals, including: array and transmission voltages, best frequency for ac power transmission, and advantages and disadvantages of ac and dc systems for this application. System and component requirements are compared with the state-of-the-art to identify areas where technological development is required.

  3. Case-study application of venture analysis: the integrated energy utility. Volume 2. Technical report

    Energy Technology Data Exchange (ETDEWEB)

    Fein, E; Gordon, T J; King, R; Kropp, F G; Shuchman, H L; Stover, J; Hausz, W; Meyer, C

    1978-11-01

    Application of venture analysis would, at a minimum, need to address issues involving careful definition of the product/service being considered; market needs that the product will satisfy; investment/manufacturing costs; minimum selling price needed to achieve desired ROI or other financial measure; market potential at relevant prices; potential for competitors to obsolete the product before investment is recovered; assessment of companies' resources and capabilities to supply the product. There is clearly no single method for performing every venture analysis, because the economic and structural environment associated with each industry varies widely. These and other factors produce differences in cost structure, marketing organizations, and nature of products which dictate that an appropriate method of venture analysis must be tailored to each industry. The initial chapter of the report presents some brief remarks concerning the important concepts that all venture analyses must consider and then describes in detail the method used for the venture analyzed in this report. The case study addresses IEUS for commercialization. The type of IEUS investigated supplies electricity and thermal energy; the thermal energy distributed in the form of high-temperature water, i.e., water from at least 90/sup 0/C upwards to 200/sup 0/C. (MCW)

  4. Commercial applications of solar total energy systems. Volume 4. Appendices. Final report. [Solar Total Energy System Evaluation Program (STESEP) code

    Energy Technology Data Exchange (ETDEWEB)

    Boobar, M.G.; McFarland, B.L.; Nalbandian, S.J.; Willcox, W.W.; French, E.P.; Smith, K.E.

    1978-07-01

    A methodology has been developed by Atomics International under contract to the Department of Energy to define the applicability of solar total energy systems (STES) to the commercial sector (e.g., retail stores, shopping centers, offices, etc.) in the United States. Candidate STES concepts were selected to provide on-site power generation capability, as well as thermal energy for both heating and cooling applications. Each concept was evaluated on the basis of its cost effectiveness (i.e., as compared to other concepts) and its ability to ultimately penetrate and capture a significant segment of this market, thereby resulting in a saving of fossil fuel resources. This volume contains the appendices. Topics include deterministic insolation model computer code; building energy usage data; computer simulation programs for building energy demand analysis; model buildings for STES evaluation; Solar Total Energy System Evaluation Program (STESEP) computer code; transient simulation of STES concept; solar data tape analysis; program listings and sample output for use with TRNSYS; transient simulation, and financial parameters sensitivities. (WHK)

  5. Application of measurement of lung volumes from MSCT images in evaluation of pulmonary function of patients with chronic obstructive pulmonary disease

    International Nuclear Information System (INIS)

    Objective: To explore the application value of lung volumes from 64 multi-slice CT (MSCT) images in patients with chronic obstructive pulmonary disease (COPD) and study the correlation between lung volumes measured by MSCT and pulmonary function test (PFT) results. Methods: 24 patients clinically diagnosed with COPD (COPD group) and 22 healthy people (control group) were selected and underwent both chest MSCT scans and PFT within one week. The total lung was scanned at full inspiration and full expiration with MSCT, respectively. The total lung volumes were measured by CT Pulmo software (Siemens, Forchheim, Germany). The quantitative total lung volumes from MSCT images were compared with PFT and SPSS13.0 was applied to assess the correlation. Results: Compared with control group, the full inspiration volume (Vin) (P<0.05), the full expiration volume (Vex) (P<0.05), and Vex/Vin (P<0.01) were elevated, while Vin-Vex was declined obviously in COPD group (P<0.05). Vin was in positive correlation with total lung capacity (TLC) (r= 0.923, P<0.01) and Vex was also in positive correlation with residual volume (RV) (r= 0.912, P<0.05), as well as Vin-Vex with vital capacity (VC) (r=0.763, P<0.01) and Vex/Vin with RV/TLC (r= 0.754, P<0.01). The Vex showed best correlation with FEV1% and FEV1/FVC (r=-0.616, P<0.01; r=-0.543, P<0.05). Vin, Vex and Vex/Vin were significantly elevated in patients with COPD compared with those in control group. Conclusion: Lung volumes obtained from MSCT images show a strong correlation with PFT results in patients with COPD. Lung volumes measured from MSCT images can be used to evaluate the pulmonary function in patients with COPD. (authors)

  6. Application of SLIM-MAUD: A test of an interactive computer-based method for organizing expert assessment of human performance and reliability: Volume 2, Appendices

    International Nuclear Information System (INIS)

    The US Nuclear Regulatory Commission (NRC) has been conducting a multiyear research program to investigate different methods for using expert judgments to estimate human error probabilities (HEPs) in nuclear power plants. One of the methods investigated, derived from multi-attribute utility theory, is the Success Likelihood Index Methodolocy implemented through Multi-Attribute Utility Decomposition (SLIM-MAUD). This report describes a systematic test application of the SLIM-MAUD methodology. The test application is evaluated on the basis of three criteria: practicality, acceptability, and usefulness. Volume I of this report represents an overview of SLIM-MAUD, describes the procedures followed in the test application, and provides a summary of the results obtained. Volume II consists of technical appendices to support in detail the materials contained in Volume I, and the users' package of explicit procedures to be followed in implementing SLIM-MAUD. The results obtained in the test application provide support for the application of SLIM-MAUD to a wide variety of applications requiring estimates of human errors

  7. Report of the Survey on the Design Review of New Reactor Applications. Volume 1 - Instrumentation and Control

    International Nuclear Information System (INIS)

    At the tenth meeting of the CNRA Working Group on the Regulation of New Reactors (WGRNR) in March 2013, the members agreed to present the responses to the Second Phase, or Design Phase, of the Licensing Process Survey as a multi-volume text. As such, each report will focus on one of the eleven general technical categories covered in the survey. The general technical categories were selected to conform to the topics covered in the International Atomic Energy Agency (IAEA) Safety Guide GS-G-4.1. This report, which is the first volume, provides a discussion of the survey responses related to Instrumentation and Control (I and C). The Instrumentation and Control category includes the twelve following technical topics: Reactor trip system, actuation systems for Engineered Safety Features (ESF), safe shutdown system, safety-related display instrumentation, information and interlock systems important to safety, controls systems, main control room, supplementary control room, diverse I and C systems, data communication systems, software reliability and cyber-security. For each technical topic, the member countries described the information provided by the applicant, the scope and level of detail of the technical review, the technical basis for granting regulatory authorisation, the skill sets required and the Level of effort needed to perform the review. Based on a comparison of the information provided in response to the survey, the following observations were made: - Among the regulatory organisations that responded to the survey, there are similarities in the design information provided by an applicant. In most countries, the design information provided by an applicant includes, but is not limited to, a description of the I and C system design and functions, a description of the verification and validation programmes, and provisions for analysis, testing, and inspection of various I and C systems. - In addition to the regulations, it is a common practice for countries

  8. Role of computation fluid dynamics in aeronautical engineering (4). Development and applications of implicit TVD finete volume code

    Energy Technology Data Exchange (ETDEWEB)

    Shima, Eiji; Jounouchi, Tadamasa

    1986-12-01

    Potential analysis in aeronautic design has reached the stage of practical use although it involves problems concerning accuracy and restrictions on its application. On the other hand, numerical analysis using Euler and Navier-Stokes (N-S) equations is based on a highly accurate theory, so is preferable, but has not reached the stage of practical use because it involves problems that shapes that can be analyzed are restricted on account of factors relating to computation lattice generation and because it involves difficulty relating to computation time. The essential factor in numerical analysis is stoutness (numeric stability). From this viewpoint, an Euler/N-S method was developed; the theory begins with TVD finite volume code, and incorporates various types of improvement to raise accuracy and shorten computation time; hence, it satisfies design requirements. The use of this method helps get solution under a wide range of flow condition without any fine adjustments, such as artificial viscosity. (6 figs, 1 tab, 10 refs)

  9. Separation of surface, subsurface and volume fatigue damage effects in AISI 348 steel for power plant applications

    Energy Technology Data Exchange (ETDEWEB)

    Klein, Martin; Nowak, David; Walther, Frank [Technical Univ. Dortmund (Germany). Dept. of Materials Test Engineering (WPT); Starke, Peter [Saarland Univ., Saarbruecken (Germany). Chair of Non-Destructive Testing and Quality Assurance; Boller, Christian [Saarland Univ., Saarbruecken (Germany). Chair of Non-Destructive Testing and Quality Assurance; Fraunhofer IZFP, Saarbruecken (Germany)

    2016-08-01

    A wide range of industries including energy, chemistry, pharmacy, textiles, food and drink, pulp and paper, etc. is using stainless steels. Metastable austenitic steels such as used in power plants and chemical industry are subjected to cyclic mechanical and thermal loading in air as well as under the influence of corrosive media. This paper provides an overview on different nondestructive and electrochemical measurement techniques, which allow differentiating fatigue damage effects in total strain controlled multiple and constant amplitude tests with respect to damage appearance on surface, in subsurface area as well as in volume of specimens or components microstructure. In addition to conventional mechanical stress-strain hysteresis curves, electrical resistance, magnetic and open circuit potential measurements have been applied to characterize the cyclic deformation behavior of the metastable austenitic steel AISI 348 (X10CrNiNb18-9) in laboratory air and in distilled water. Based on these results obtained, the paper provides an outlook on the possibility for an efficient (remaining) fatigue life evaluation approach, which is adapted to the needs of the application areas.

  10. Double-echo perfusion-weighted MR imaging: basic concepts and application in brain tumors for the assessment of tumor blood volume and vascular permeability

    Energy Technology Data Exchange (ETDEWEB)

    Uematsu, Hidemasa [University of Fukui, Department of Radiology, Faculty of Medical Sciences, Fukui (Japan); Maeda, Masayuki [Mie University School of Medicine, Department of Radiology, Mie (Japan)

    2006-01-01

    Perfusion-weighted magnetic resonance (MR) imaging using contrast agents plays a key role in characterizing tumors of the brain. We have shown that double-echo perfusion-weighted MR imaging (DEPWI) is potentially useful in assessing brain tumors. Quantitative indices, such as tumor blood volume, are obtained using DEPWI, which allows correction of underestimation of tumor blood volume due to leakage of contrast agents from tumor vessels, in addition to simultaneous acquisition of tumor vessel permeability. This article describes basic concepts of DEPWI and demonstrates clinical applications in brain tumors. (orig.)

  11. Application of ultradisperse magnetic adsorbents for removal of small concentrations of pollutants from large volumes of water

    Science.gov (United States)

    Nechitailo, Galina S.; Kuznetsov, Anatoli; Kuznetsov, Oleg

    2016-07-01

    with the adsorbed toluidine blue were removed from the solution by magnetic separation. The sorbent was proven to have high sorption capacity and rapid adsorption kinetics for toluidine blue. These experiments demonstrated the validity of the method, where a small concentration of a pollutant was successfully collected from a large volume of water. By varying the ratio of the sorbent/pollutant, it is possible to optimize the sorbent use and the time required to adsorb all pollutant present in the treated water. A variety of magnetically controlled sorbents can be designed and used in this method, from broad-spectrum adsorbing sorbents to sorbents specifically targeting a particular pollutant. These sorbents can be used either individually or as mixtures of sorbents with different properties, depending on the desired purification goals. Simplicity and scalability of this method allow a variety of ecological applications, as well as industrial ones, from process water purification to wastewater treatment.

  12. An Industrial Perspective of CAM/ROB Fuzzy Integrated Postprocessing Implementation for Redundant Robotic Workcells Applicability for Big Volume Prototyping

    Science.gov (United States)

    Andrés, J.; Gracia, L.; Tornero, J.; García, J. A.; González, F.

    2009-11-01

    The implementation of a postprocessor for the NX™ platform (Siemens Corp.) is described in this paper. It is focused on a milling redundant robotic milling workcell consisting of one KUKA KR 15/2 manipulator (6 rotary joints, KRC2 controller) mounted on a linear axis and synchronized with a rotary table (i.e., two additional joints). For carrying out a milling task, a choice among a set of possible configurations is required, taking into account the ability to avoid singular configurations by using both additional joints. Usually, experience and knowledge of the workman allow an efficient control in these cases, but being it a tedious job. Similarly to this expert knowledge, a stand-alone fuzzy controller has been programmed with Matlab's Fuzzy Logic Toolbox (The MathWorks, Inc.). Two C++ programs complement the translation of the toolpath tracking (expressed in the Cartesian space) from the NX™-CAM module into KRL (KUKA Robot Language). In order to avoid singularities or joint limits, the location of the robot and the workpiece during the execution of the task is fit after an inverse kinematics position analysis and a fuzzy inference (i.e., fuzzy criterion in the Joint Space). Additionally, the applicability of robot arms for the manufacture of big volume prototypes with this technique is proven by means of one case studied. It consists of a big orographic model to simulate floodways, return flows and retention storage of a reservoir in the Mijares river (Puebla de Arenoso, Spain). This article deals with the problem for a constant tool orientation milling process and sets the technological basis for future research at five axis milling operations.

  13. Impacts of equations of state (EOS) and impurities on the volume calculation of CO2 mixtures in the applications of CO2 capture and storage (CCS) processes

    International Nuclear Information System (INIS)

    Volume property is the necessary thermodynamic property in the design and operation of the CO2 capture and storage system (CCS). Because of their simple structures, cubic equations of state (EOS) are preferable to be applied in predicting volumes for engineering applications. This paper evaluates the reliabilities of seven cubic EOS, including PR, PT, RK, SRK, MPR, MSRK and ISRK for predicting volumes of binary CO2 mixtures containing CH4, H2S, SO2, Ar and N2, based on the comparisons with the collected experimental data. Results show that for calculations on the volume properties of binary CO2 mixtures, PR and PT are generally superior to others for all of the studied mixtures. In addition, it was found that the binary interaction parameter has clear effects on the calculating accuracy of an EOS in the volume calculations of CO2 mixtures. In order to improve the accuracy, kij was calibrated for all of the EOS regarding the gas and liquid phases of all the studied binary CO2 mixtures, respectively.

  14. Application of 3D Scanned Imaging Methodology for Volume, Surface Area, and Envelope Density Evaluation of Densified Biomass

    Science.gov (United States)

    Measurement of surface area, volume, and density is an essential for quantifying, evaluating, and designing the biomass densification, storage, and transport operations. Acquiring accurate and repeated measurements of these parameters for hygroscopic densified biomass are not straightforward and on...

  15. Volume-controlled buckling of thin elastic shells: Application to crusts formed on evaporating partially-wetted droplets

    OpenAIRE

    Head, D. A.

    2006-01-01

    Motivated by the buckling of glassy crusts formed on evaporating droplets of polymer and colloid solutions, we numerically model the deformation and buckling of spherical elastic caps controlled by varying the volume between the shell and the substrate. This volume constraint mimics the incompressibility of the unevaporated solvent. Discontinuous buckling is found to occur for sufficiently thin and/or large contact angle shells, and robustly takes the form of a single circular region near the...

  16. Developments and innovation in carbon dioxide (CO{sub 2}) capture and storage technology. Volume 1: carbon dioxide (CO{sub 2}) capture, transport and industrial applications

    Energy Technology Data Exchange (ETDEWEB)

    Mercedes Maroto-Valer, M. (ed.)

    2010-07-01

    This volume initially reviews the economics, regulation and planning of CCS for power plants and industry, and goes on to explore developments and innovation in post- and pre-combustion and advanced combustion processes and technologies for CO{sub 2} capture in power plants. This coverage is extended with sections on CO{sub 2} compression, transport and injection and industrial applications of CCS technology, including in the cement and concrete and iron and steel industries.

  17. Application of Imaging Techniques to Mechanics of Materials and Structures, Volume 4 : Proceedings of the 2010 Annual Conference on Experimental and Applied Mechanics

    CERN Document Server

    2013-01-01

    This the fourth volume of six from the Annual Conference of the Society for Experimental Mechanics, 2010, brings together 58 chapters on Application of Imaging Techniques to Mechanics of Materials and Structure. It presents findings from experimental and computational investigations involving a range of imaging techniques including Recovery of 3D Stress Intensity Factors From Surface Full-field Measurements, Identification of Cohesive-zone Laws From Crack-tip Deformation Fields, Application of High Speed Digital Image Correlation for Vibration Mode Shape Analysis, Characterization of Aluminum Alloys Using a 3D Full Field Measurement, and Low Strain Rate Measurements on Explosives Using DIC.

  18. Application of machine learning methods to describe the effects of conjugated equine estrogens therapy on region-specific brain volumes

    OpenAIRE

    Casanova, Ramon; Espeland, Mark A.; Goveas, Joseph S; Davatzikos, Christos; Gaussoin, Sarah A.; Maldjian, Joseph A.; Brunner, Robert L.; Kuller, Lewis H.; Johnson, Karen C.; Mysiw, W. Jerry; Wagner, Benjamin; Susan M. Resnick

    2011-01-01

    Use of conjugated equine estrogens (CEE) has been linked to smaller regional brain volumes in women aged ≥65 years, however it is unknown whether this results in a broad-based characteristic pattern of effects. Structural MRI was used to assess regional volumes of normal tissue and ischemic lesions among 513 women who had been enrolled in a randomized clinical trial of CEE therapy for an average of 6.6 years, beginning at ages 65-80 years. A multivariate pattern analysis, based on a machine l...

  19. Applicability of the theory of volume filling of micropores to adsorption of caprolactam from aqueous solutions with active carbons

    Energy Technology Data Exchange (ETDEWEB)

    Khodorov, E.I.; Kazakov, V.A.; Semerikova, V.V.; Surinova, S.I.

    1985-06-10

    The absence of a scientifically based method of selecting adsorbents in the extraction of organic substances from waste water and solution which would allow for their multicycle use in adsorption-desorption stages often prevents the introduction of adsorption technology into industrial practice. This paper demonstrates the possibility of calculating the adsorption equilibrium of highly soluble organic compounds with the theory of volume filling of micropores equations in consideration of the activities of the extracted component in the solution and the change in the partial affinity coefficient with the degree of filling of the adsorption volume on the example of extraction of caprolactam from aqueous solutions.

  20. Comparison of an ultra-low volume (ULV sprayer against a conventional sprayer, for foliar fertiliser and fungicide applications in turfgrass

    Directory of Open Access Journals (Sweden)

    Ferguson Jason Connor

    2016-01-01

    Full Text Available Two field studies (I and II at the University of Nebraska-Lincoln: John Seaton Anderson Turfgrass Research Facility near Mead, NE, USA, were conducted to determine if a new ultra-low volume (ULV sprayer can apply foliar nutrient, growth regulator, and fungicide treatments, in a manner similar to that of a conventional sprayer. Treatments were applied over creeping bentgrass ‘L-93’ (Agrostis stolonifera L. managed as a fairway at 561 l · ha−1 and 47 l · ha−1 with the conventional and ULV sprayer, respectfully. Data were collected for chlorophyll content with a chlorophyll meter, and for the normalised difference vegetation index (NDVI with a turf colour meter. Each plot was harvested for biomass at 21 days after treatment. Study II compared the ULV sprayer and a conventional sprayer, for the control of brown patch (Rhizoctonia solani Kuhn in creeping bentgrass. The treatments were propiconazole and azoxystrobin. Spray volume was 561 l · ha−1 for the conventional sprayer, and 19 l · ha−1 for the ULV sprayer. Statistical differences in turf quality or dry weight reductions between the conventional and ULV sprayer were not detected. Brown patch control was also similar between the two sprayers, but azoxystrobin provided better control than propiconazole. Even with a 30-fold decrease in application volume, the results indicated that the Kamterter ULV sprayer may be a useful and effective management option for foliar fertiliser and fungicide applications in turfgrass.

  1. Dynamic Thermodynamics with Internal Energy, Volume, and Amount of Moles as States : Application to Liquefied Gas Tank

    NARCIS (Netherlands)

    Arendsen, A. R. J.; Versteeg, G. F.

    2009-01-01

    Dynamic models for process design, optimization, and control usually solve a set of heat and/or mass balances as a function of time and/or position in the process. To obtain more robust dynamic models and to minimize the amount of assumptions, internal energy, volume, and amount of moles are chosen

  2. Application of Partial Volume Effect Correction and 4D PET in the Quantification of FDG Avid Lung Lesions

    NARCIS (Netherlands)

    Salavati, Ali; Borofsky, Samuel; Boon-Keng, Teo K.; Houshmand, Sina; Khiewvan, Benjapa; Saboury, Babak; Codreanu, Ion; Torigian, Drew A.; Zaidi, Habib; Alavi, Abass

    2015-01-01

    Purpose: The aim of this study is to assess a software-based method with semiautomated correction for partial volume effect (PVE) to quantify the metabolic activity of pulmonary malignancies in patients who underwent non-gated and respiratory-gated 2-deoxy-2-[F-18]fluoro-D-glucose (FDG)-positron emi

  3. Spatial and temporal single-cell volume estimation by a fluorescence imaging technique with application to astrocytes in primary culture

    Science.gov (United States)

    Khatibi, Siamak; Allansson, Louise; Gustavsson, Tomas; Blomstrand, Fredrik; Hansson, Elisabeth; Olsson, Torsten

    1999-05-01

    Cell volume changes are often associated with important physiological and pathological processes in the cell. These changes may be the means by which the cell interacts with its surrounding. Astroglial cells change their volume and shape under several circumstances that affect the central nervous system. Following an incidence of brain damage, such as a stroke or a traumatic brain injury, one of the first events seen is swelling of the astroglial cells. In order to study this and other similar phenomena, it is desirable to develop technical instrumentation and analysis methods capable of detecting and characterizing dynamic cell shape changes in a quantitative and robust way. We have developed a technique to monitor and to quantify the spatial and temporal volume changes in a single cell in primary culture. The technique is based on two- and three-dimensional fluorescence imaging. The temporal information is obtained from a sequence of microscope images, which are analyzed in real time. The spatial data is collected in a sequence of images from the microscope, which is automatically focused up and down through the specimen. The analysis of spatial data is performed off-line and consists of photobleaching compensation, focus restoration, filtering, segmentation and spatial volume estimation.

  4. NASA Historical Data Book. Volume 6; NASA Space Applications, Aeronautics and Space Research and Technology, Tracking and Data Acquisition/Support Operations, Commercial Programs and

    Science.gov (United States)

    Rumerman, Judy A.

    2000-01-01

    This sixth volume of the NASA Historical Data Book is a continuation of those earlier efforts. This fundamental reference tool presents information, much of it statistical, documenting the development of several critical areas of NASA responsibility for the period between 1979 and 1988. This volume includes detailed information on the space applications effort, the development and operation of aeronautics and space research and technology programs, tracking and data acquisition/space operations, commercial programs, facilities and installations, personnel, and finances and procurement during this era. Special thanks are owed to the student research assistants who gathered and input much of the tabular material-a particularly tedious undertaking. There are numerous people at NASA associated with historical study, technical information, and the mechanics of publishing who helped in myriad ways in the preparation of this historical data book.

  5. EXCEL VBA Application to Achieve the Image Volume Name%EXCEL中应用VBA实现图片的批量命名

    Institute of Scientific and Technical Information of China (English)

    孟伟

    2011-01-01

    Visual Basic for Applications (VBA) is a macro language of Visual Basic, it's mainly used to extend functionality of Windows applications, especially Microsoft Office software. It can be said that it is an application visual Basic Script. This article focuses on the use of VBA in EXCEL to achieve the volume image file name.%VisualBasicforApplications(VBA)是一种VisualBasic的一种宏语言,主要能用来扩展Windows的应用程式功能,特别是MicrosoftOffice软件。也可说是一种应用程式视觉化的BasicScript。本文着重介绍运用VBA在EXCEL中实现对图片文件的批量命名。

  6. Application of SLIM-MAUD: a test of an interactive computer-based method for organizing expert assessment of human performance and reliability. Volume 1. Main report

    International Nuclear Information System (INIS)

    The US Nuclear Regulatory Commission has been conducting a multiyear research program to investigate different methods for using expert judgments to estimate human error probabilities in nuclear power plants. One of the methods investigated, derived from multi-attribute utility theory, is the Success Likelihood Index Methodology implemented through Multi-Attribute Utility Decomposition (SLIM-MAUD). This report describes a systematic test application of the SLIM-MAUD methodology. The test application is evaluated on the basis of three criteria: practicality, acceptability, and usefulness. Volume I of this report presents an overview of SLIM-MAUD, describes the procedures followed in the test application, and provides a summary of the results obtained. 14 refs

  7. Excess molar volumes of 1,3 propanediol + (C1-C5 alkan-1-ols: Application of cubic EOS

    Directory of Open Access Journals (Sweden)

    Almasi Mohammad

    2012-01-01

    Full Text Available Densities of the binary mixtures consist of methanol, ethanol, 1- propanol, 1-butanol and 1-pentanol with 1,3 Propanediol were measured at temperatures (293.15, 298.15, 303.15 and 313.15 K and atmospheric pressure. Measurements have been made over the full range of compositions and for the pure compounds by using a vibrating tube densimeter. Excess molar volumes have been obtained from these experimental results and were fitted to a Redlich-Kister type expansion. The results were interpreted in terms of molecular interactions and structural factors of the alcohols. It was observed that an increase of the alcohol carbon chain length led to lower interactions on mixing. The Peng-Robinson-Stryjek-Vera (PRSV equation of state has been used to correlate the binary excess molar volumes.

  8. Robust finite volume schemes and variational inversions for 2D shallow water models. Application to flood plain dynamics

    OpenAIRE

    Couderc, F.; Monnier, J; Vila, J.-P; Larnier, K.; Madec, R; Dartus, D.

    2015-01-01

    This study proposes original combinations of higher order Godunov type finite volume schemes and time discretization schemes for the 2d shallow water equations, leading to fully second-order accuracy with well-balanced property. Also accuracy, positiveness and stability properties in presence of dynamic wet/dry fronts is demonstrated. The test cases are the classical ones plus extra new ones representing the geophysical flow features and difficulties. Preliminary numerical experiments give so...

  9. Quantification of slag heap volumes and masses through the use of induced polarization : application to the Castel-Minier site

    OpenAIRE

    Florsch, Nicolas; Llubes, M.; Tereygeol, E.; A. Ghorbani; Roblet, P.

    2011-01-01

    When used for archaeological purposes, geophysical methods are often useful for the exploration, detection and mapping of archaeological remains. In the case of ancient metallurgical activities, slag accumulations form precious mineral records of these activities. Evaluating the volume of slag produced in such locations is an important issue, since it enables an estimate of the amount of metal produced in the smeltery. Unfortunately, slags themselves cannot be easily detected by DC electrical...

  10. Mosquito Management on National Wildlife Refuges, Ecosystem Effects Study. Phase II, Part 1 - Effects of Ultra Low Volume Applications of Pyrethrin, Malathion and Permethrin on Macro-Invertebrates in the Sacramento National Wildlife Refuge, California

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Mosquito control districts often use ultra-low volume (ULV) applications of insecticides to control adult mosquitoes. Few field studies have tested the effects of...

  11. Environmental Report 1996, Volume 2

    Energy Technology Data Exchange (ETDEWEB)

    Harrach, R.J.

    1996-01-01

    This is Volume 2 of the Lawrence Livermore National Laboratory`s (LLNL`s) annual Environmental Report 1996, prepared for the US Department of Energy. Volume 2 supports Volume 1 summary data and is essentially a detailed data report that provides individual data points, where applicable. Volume 2 includes information on monitoring of air, air effluents, sewerable water, surface water, ground water, soil and sediment, vegetation and foodstuff, environmental radiation, and quality assurance.

  12. Multiphase flow modelling using non orthogonal collocated finite volumes : application to fluid catalytical cracking and large scale geophysical flows.

    Science.gov (United States)

    Martin, R. M.; Nicolas, A. N.

    2003-04-01

    A modeling approach of gas solid flow, taking into account different physical phenomena such as gas turbulence and inter-particle interactions is presented. Moment transport equations are derived for the second order fluctuating velocity tensor which allow to involve practical closures based on single phase turbulence modeling on one hand and kinetic theory of granular media on the other hand. The model is applied to fluid catalytic cracking processes and explosive volcanism. In the industry as well as in the geophysical community, multiphase flows are modeled using a finite volume approach and a multicorrector algorithm in time in order to determine implicitly the pressures, velocities and volume fractions for each phase. Pressures, and velocities are generally determined at mid-half mesh step from each other following the staggered grid approach. This ensures stability and prevents oscillations in pressure. It allows to treat almost all the Reynolds number ranges for all speeds and viscosities. The disadvantages appear when we want to treat more complex geometries or if a generalized curvilinear formulation of the conservation equations is considered. Too many interpolations have to be done and accuracy is then lost. In order to overcome these problems, we use here a similar algorithm in time and a Rhie and Chow interpolation (1983) of the collocated variables and essentially the velocities at the interface. The Rhie and Chow interpolation of the velocities at the finite volume interfaces allows to have no oscillations of the pressure without checkerboard effects and to stabilize all the algorithm. In a first predictor step, fluxes at the interfaces of the finite volumes are then computed using 2nd and 3rd order shock capturing schemes of MUSCL/TVD or Van Leer type, and the orthogonal stress components are treated implicitly while cross viscous/diffusion terms are treated explicitly. Pentadiagonal linear systems are solved in each geometrical direction (the so

  13. Application of ERAS-model and Prigogine-Flory-Patterson theory to excess molar volumes for ternary mixtures of (2-chlorobutane + butylacetate + isobutanol) at T = 298.15 K

    Energy Technology Data Exchange (ETDEWEB)

    Khanlarzadeh, K. [Department of Physical Chemistry, Faculty of Chemistry, University of Bu-Ali Sina, Hamedan (Iran, Islamic Republic of); Iloukhani, H., E-mail: iloukhani@basu.ac.ir [Department of Physical Chemistry, Faculty of Chemistry, University of Bu-Ali Sina, Hamedan (Iran, Islamic Republic of)

    2011-11-15

    Highlights: > Density of ternary and three binary mixtures of (2-chlorobutane + butylacetate + isobutanol) determined. > Excess molar volume, partial molar volume and apparent molar volume were calculated. > Excess molar volume was correlated as a function of mole fraction by using the Redlich-Kister and Cibulka equation for all mixtures. > The experimental results have been used to test the applicability of the ERAS-model and PFP theory. - Abstract: Densities of the ternary mixture consisting of {l_brace}2-chlorobutane (1) + butylacetate (2) + isobutanol (3){r_brace} and related binary mixtures were measured over the whole range of composition at T = 298.15 K and ambient pressure. Excess molar volumes V{sub m}{sup E} for the mixtures were derived and correlated as a function of mole fraction by using the Redlich-Kister and the Cibulka equations for binary and ternary mixtures, respectively. From the experimental data, partial molar volumes, V-bar{sub m,i} excess partial molar volumes, V-bar{sub i}{sup E} partial molar volumes at infinite dilution V-bar{sub m,i}{sup 0} and apparent molar volumes V-bar{sub {phi},i} were also calculated. For all binary mixtures over the entire range of mole fractions V{sub m}{sup E} data are positive. The experimental results of the constituted binary mixtures have been used to test the applicability of the extended real associated solution (ERAS-model) and Prigogine-Flory-Paterson (PFP) theory.

  14. Are you bleeding? Validation of a machine-learning algorithm for determination of blood volume status: application to remote triage.

    Science.gov (United States)

    Rickards, Caroline A; Vyas, Nisarg; Ryan, Kathy L; Ward, Kevin R; Andre, David; Hurst, Gennifer M; Barrera, Chelsea R; Convertino, Victor A

    2014-03-01

    Due to limited remote triage monitoring capabilities, combat medics cannot currently distinguish bleeding soldiers from those engaged in combat unless they have physical access to them. The purpose of this study was to test the hypothesis that low-level physiological signals can be used to develop a machine-learning algorithm for tracking changes in central blood volume that will subsequently distinguish central hypovolemia from physical activity. Twenty-four subjects underwent central hypovolemia via lower body negative pressure (LBNP), and a supine-cycle exercise protocol. Exercise workloads were determined by matching heart rate responses from each LBNP level. Heart rate and stroke volume (SV) were measured via Finometer. ECG, heat flux, skin temperature, galvanic skin response, and two-axis acceleration were obtained from an armband (SenseWear Pro2) and used to develop a machine-learning algorithm to predict changes in SV as an index of central blood volume under both conditions. The algorithm SV was retrospectively compared against Finometer SV. A model was developed to determine whether unknown data points could be correctly classified into these two conditions using leave-one-out cross-validation. Algorithm vs. Finometer SV values were strongly correlated for LBNP in individual subjects (mean r = 0.92; range 0.75-0.98), but only moderately correlated for exercise (mean r = 0.50; range -0.23-0.87). From the first level of LBNP/exercise, the machine-learning algorithm was able to distinguish between LBNP and exercise with high accuracy, sensitivity, and specificity (all ≥90%). In conclusion, a machine-learning algorithm developed from low-level physiological signals could reliably distinguish central hypovolemia from exercise, indicating that this device could provide battlefield remote triage capabilities. PMID:24408992

  15. High-resolution neutron protein crystallography with radically small crystal volumes: Application of perdeuteration to human aldose reductase

    International Nuclear Information System (INIS)

    Neutron diffraction data have been collected to 2.2 (angstrom) resolution from a small (0.15 mm3) crystal of perdeuterated human aldose reductase (h-AR; MW = 36 kDa) in order to help to determine the protonation state of the enzyme. h-AR belongs to the aldo-keto reductase family and is implicated in diabetic complications. Its ternary complexes (h-AR-coenzyme NADPH-selected inhibitor) provide a good model to study both the enzymatic mechanism and inhibition. Here, the successful production of fully deuterated human aldose reductase (h-AR(D)), subsequent crystallization of the ternary complex h-AR(D)-NADPH-IDD594 and neutron Laue data collection at the LADI instrument at ILL using a crystal volume of just 0.15 mm3 are reported. Neutron data were recorded to 2 (angstrom) resolution, with subsequent data analysis using data to 2.2 (angstrom). This is the first fully deuterated enzyme of this size (36 kDa) to be solved by neutron diffraction and represents a milestone in the field, as the crystal volume is at least one order of magnitude smaller than those usually required for other high-resolution neutron structures determined to date. This illustrates the significant increase in the signal-to-noise ratio of data collected from perdeuterated crystals and demonstrates that good-quality neutron data can now be collected from more typical protein crystal volumes. Indeed, the signal-to-noise ratio is then dominated by other sources of instrument background, the nature of which is under investigation. This is important for the design of future instruments, which should take maximum advantage of the reduction in the intrinsic diffraction pattern background from fully deuterated samples.

  16. Application of 3D laser scanner in ore volume measurement%三维激光扫描仪在测算矿方量中的应用

    Institute of Scientific and Technical Information of China (English)

    黄有; 郑坤; 刘修国; 王红平; 阮进成

    2012-01-01

    Recently, with the rapid development of 3D laser scanning technique, 3D laser scanners have been extensively applied in many fields. The paper mainly described the application of 3D laser scanner in ore volume measure. The volume of ore hea Pwas calculated after it was scanned by the Riegl VZ-400 3D laser scanner. The precision was confirmed by the comparison of the control points' geodetic coordinates measured by GPS and scanner coordinates. The result of experiment showed that the precision of 3D laser scanner could satisfy the requirements of ore volume measurement. In conclusion, the paper summarized the advantage of the usage of 3D laser scanning technology in ore volume measurement.%本文通过使用Riegl VZ-400型号的三维激光扫描仪对某矿堆进行了扫描,对扫描数据进行三维建模后测算矿堆的矿方量.采用GPS测量一定数量控制点的大地坐标与扫描仪测量的坐标进行比较来验证扫描数据的精度,得到平面坐标的差值绝对值最大为0 018m,而高程的差值绝对值最大为0.028m,实验结果表明三维激光扫描仪满足测算矿方量的精度.

  17. A prospective study of the effects of ultralow volume (ULV) aerial application of malathion on epidemic Plasmodium falciparum malaria. III. Ecologic aspects.

    Science.gov (United States)

    McLean, R G; Spillane, J T; Miles, J W

    1975-03-01

    The effects of aerial ultralow volume (ULV) malathion on selected species of nontarget animals in Haiti are reported. Mortality of certain groups of insects such as bees, flies, beetles, and butterflies was observed immediately following spray application. Minor fish mortality occurred only in shallow water exposed to direct spray. The brain acetylcholine esterase levels of living fish, tree lizards, birds and bats collected from treated areas were not significantly reduced. No ill or dead animals, besides the few fish, were seen even when maximum exposure occurred. Only minor changes in the feeding behavior of some insectivorous birds were observed. The relative bird density decreased substantially for only one species during the study, and other factors besides treatment were considered to be the reasons for the decline. Aerial applications of ULV malathion at dosages sufficient to dramatically reduce anopheline populations did not significantly affect nontarget vertebrates in this tropical environment. PMID:1091169

  18. Novel application of confocal laser scanning microscopy and 3D volume rendering toward improving the resolution of the fossil record of charcoal.

    Directory of Open Access Journals (Sweden)

    Claire M Belcher

    Full Text Available Variations in the abundance of fossil charcoals between rocks and sediments are assumed to reflect changes in fire activity in Earth's past. These variations in fire activity are often considered to be in response to environmental, ecological or climatic changes. The role that fire plays in feedbacks to such changes is becoming increasingly important to understand and highlights the need to create robust estimates of variations in fossil charcoal abundance. The majority of charcoal based fire reconstructions quantify the abundance of charcoal particles and do not consider the changes in the morphology of the individual particles that may have occurred due to fragmentation as part of their transport history. We have developed a novel application of confocal laser scanning microscopy coupled to image processing that enables the 3-dimensional reconstruction of individual charcoal particles. This method is able to measure the volume of both microfossil and mesofossil charcoal particles and allows the abundance of charcoal in a sample to be expressed as total volume of charcoal. The method further measures particle surface area and shape allowing both relationships between different size and shape metrics to be analysed and full consideration of variations in particle size and size sorting between different samples to be studied. We believe application of this new imaging approach could allow significant improvement in our ability to estimate variations in past fire activity using fossil charcoals.

  19. A 2D finite volume model for bebris flow and its application to events occurred in the Eastern Pyrenees

    Institute of Scientific and Technical Information of China (English)

    V.MEDINA; A.BATEMAN; M.H(U)RLIMANN

    2008-01-01

    FLATModel is a 2D finite volume code that contains several original approaches to improve debris-flow simulation.Firstly,FLATModel incorporates a "stop-and-go" technique in each cell to allow continuous collapses and remobilizations of the debris-flow mass.Secondly,flow velocity and consequently yield stress is directly associated with the type of rheology to improve boundary accuracy.Thirdly,a simple approach for entrainment is also included in the model to analyse the effect of basal erosion of debris flows.FLATMODEL was tested at several events that occurred in the Eastern Pyrenees and simulation results indicated that the model can represent rather well the different characteristics observed in the field.

  20. Application of Molecular Interaction Volume Model for Phase Equilibrium of Sn-Based Binary System in Vacuum Distillation

    Science.gov (United States)

    Kong, Lingxin; Yang, Bin; Xu, Baoqiang; Li, Yifu

    2014-09-01

    Based on the molecular interaction volume model (MIVM), the activities of components of Sn-Sb, Sb-Bi, Sn-Zn, Sn-Cu, and Sn-Ag alloys were predicted. The predicted values are in good agreement with the experimental data, which indicate that the MIVM is of better stability and reliability due to its good physical basis. A significant advantage of the MIVM lies in its ability to predict the thermodynamic properties of liquid alloys using only two parameters. The phase equilibria of Sn-Sb and Sn-Bi alloys were calculated based on the properties of pure components and the activity coefficients, which indicates that Sn-Sb and Sn-Bi alloys can be separated thoroughly by vacuum distillation. This study extends previous investigations and provides an effective and convenient model on which to base refining simulations for Sn-based alloys.

  1. Finite Volume schemes on unstructured grids for non-local models: Application to the simulation of heat transport in plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Goudon, Thierry, E-mail: thierry.goudon@inria.fr [Team COFFEE, INRIA Sophia Antipolis Mediterranee (France); Labo. J.A. Dieudonne CNRS and Univ. Nice-Sophia Antipolis (UMR 7351), Parc Valrose, 06108 Nice cedex 02 (France); Parisot, Martin, E-mail: martin.parisot@gmail.com [Project-Team SIMPAF, INRIA Lille Nord Europe, Park Plazza, 40 avenue Halley, F-59650 Villeneuve d' Ascq cedex (France)

    2012-10-15

    In the so-called Spitzer-Haerm regime, equations of plasma physics reduce to a nonlinear parabolic equation for the electronic temperature. Coming back to the derivation of this limiting equation through hydrodynamic regime arguments, one is led to construct a hierarchy of models where the heat fluxes are defined through a non-local relation which can be reinterpreted as well by introducing coupled diffusion equations. We address the question of designing numerical methods to simulate these equations. The basic requirement for the scheme is to be asymptotically consistent with the Spitzer-Haerm regime. Furthermore, the constraints of physically realistic simulations make the use of unstructured meshes unavoidable. We develop a Finite Volume scheme, based on Vertex-Based discretization, which reaches these objectives. We discuss on numerical grounds the efficiency of the method, and the ability of the generalized models in capturing relevant phenomena missed by the asymptotic problem.

  2. Low concentration ratio solar array for low Earth orbit multi-100kW application. Volume 2: Drawings

    Science.gov (United States)

    Nalbandian, S. J.; French, E. P.

    1982-01-01

    A preliminary design effort directed toward a low concentration ratio photovoltaic array system based on 1984 technology and capable of delivering multi-hundred kilowatts (300 kW to 100 kW range) in low Earth orbit. The array system consists of two or more array modules each capable of delivering between 113 kW to 175 kW using silicon solar cells or gallium arsenide solar cells, respectively. The array module deployed area is 1320 square meters and consists of 4356 pyramidal concentrator elements. The module, when stowed in the Space Shuttle's payload bay, has a stowage volume of a cube with 3.24 meters on a side. The concentrator elements are sized for a geometric concentration ratio (GCR) of six with an aperture area of 0.5 meters x 0.5 meters. Drawings for the preliminary design configuration and for the test hardware that was fabricated for design evaluation and test are provided.

  3. Representative elementary volume assessment of three-dimensional x-ray microtomography images of heterogeneous materials: Application to limestones

    Science.gov (United States)

    Rozenbaum, O.; du Roscoat, S. Rolland

    2014-05-01

    Over the last 15 years, x-ray microtomography has become a useful technique to obtain morphological, structural, and topological information on materials. Moreover, these three-dimensional (3D) images can be used as input data to assess certain properties (e.g., permeability) or to simulate phenomena (e.g., transfer properties). In order to capture all the features of interest, high spatial resolution is required. This involves imaging small samples, raising the question of the representativity of the data sets. In this article, we (i) present a methodology to analyze the microstructural properties of complex porous media from 3D images, (ii) assess statistical representative elementary volumes (REVs) for such materials; and (iii) establish criteria to delimit these REVs. In the context of cultural heritage conservation, a statistical study was done on 30 quarry samples for three sorts of stones. We first present the principles of x-ray microtomography experiments and emphasize the care that must be taken in the 3D image segmentation steps. Results show that statistical REVs exist for these media and are reached for the image sizes studied (1300 × 1300 × 1000 voxels) for two characteristics: porosity and chord length distributions. Furthermore, the estimators used (porosity, autocorrelation function, and chord length distributions) are sufficiently sensitive to quantitatively distinguish these three porous media from each other. Lastly, this study puts forward criteria based on the above-mentioned estimators to evaluate the REVs. These criteria avoid having to repeat the statistical study for each new material studied. This is particularly relevant to quantitatively monitor the modifications in materials (weathering, deformation …) or to determine the smallest 3D volume for simulation in order to reduce computing time.

  4. Effectiveness of ultra-low volume nighttime applications of an adulticide against diurnal Aedes albopictus, a critical vector of dengue and chikungunya viruses.

    Directory of Open Access Journals (Sweden)

    Ary Farajollahi

    Full Text Available Aedes albopictus, the Asian tiger mosquito, continues expanding its geographic range and involvement in mosquito-borne diseases such as chikungunya and dengue. Vector control programs rarely attempt to suppress this diurnal species with an ultra-low volume (ULV adulticide because for maximum efficacy applications are conducted at night. During 2009-2011 we performed experimental nighttime applications of a novel adulticide (DUET® against field populations of Ae. albopictus within an urban site composed of approximately 1,000 parcels (home and yard in northeastern USA. Dual applications at mid label rate of the adulticide spaced one or two days apart accomplished significantly higher control (85.0 ± 5.4% average reduction than single full rate applications (73.0 ± 5.4%. Our results demonstrate that nighttime ULV adulticiding is effective in reducing Ae. albopictus abundance and highlight its potential for use as part of integrated pest management programs and during disease epidemics when reducing human illness is of paramount importance.

  5. Institutional origins of the Department of Energy: the Office of Military Application. Energy History Series Volume 1, No. 1

    International Nuclear Information System (INIS)

    The Department of Energy Organization Act of 1977 brought together for the first time in one department most of the government's energy programs. With these programs came a score of organizational entities, each with its own history and traditions, from a dozen departments and independent agencies. This report traces the history of the Office of Military Application, from its inception as the Division of Military Application in the Atomic Energy Commission, through the Energy Research and Development Administration to its present status as an office in the Department of Energy

  6. Innovative housing '93, proceedings. Volume 3: Applications and demonstrations. L'habitation a la fine pointe '93, comptes rendus. Tome 3: Applications et demonstrations

    Energy Technology Data Exchange (ETDEWEB)

    1994-01-01

    A conference was held with the objective of creating an international forum for the promotion of more energy efficient and environmentally responsible housing. A compilation is presented of papers presented at the conference stream dedicated to applications and demonstrations. Topics of the papers included international low-rise demonstration projects, healthy housing and advanced houses, multi-storey applications, industrialized building systems, and applications in cold and hot climates. Specific innovations included use of solar heating, recycled materials, high levels of thermal insulation, renewable energies, high-efficiency windows, and advanced structural components. Separate abstracts have been prepared for 34 papers from this compendium.

  7. Compact uncooled amorphous silicon 160x120 IRFPA with 25 μm pixel-pitch for large volume applications

    Science.gov (United States)

    Tissot, J. L.; Legras, O.; Minassian, C.; Robert, P.; Fieque, B.; Tinnes, S.; Dupont, B.; Yon, J. J.; Arnaud, A.

    2007-10-01

    This paper reviews specifications and performances of a 160 x 120 uncooled infrared focal plane array made from amorphous silicon micro bolometer with a pixel-pitch of 25 μm, integrated in a LCC package. This detector has been specifically designed for being produced in large volume. The detector has kept all the innovations developed on the full TV format ROIC (detector configuration by serial link, low power consumption or wide electrical dynamic range... ) and offers an advanced TEC-less focal plane array well adapted to low end thermal imaging cameras. The specific appeal of this unit lies in the miniaturization of the packaging and its extremely light weight.In the last part of the paper, we will look more closely at electro-optical performances of this TEC-less product 160 x 120 as well as the other 25 μm products like the 384 x 288. We will insist on the wide thermal dynamic range and the low consumption achieved thanks to the mastering of the amorphous silicon technology coupled with the innovation in the ROIC design.

  8. Uncooled amorphous silicon 160 x 120 IRFPA with 25 μm pixel-pitch for large volume applications

    Science.gov (United States)

    Vilain, M.; Tissot, J. L.; Legras, O.; Yon, J. J.; Minassian, C.; Fièque, B.; Chiappa, J. M.

    2008-03-01

    This paper reviews the specifications and performances of a 160 × 120 uncooled infrared focal plane array made from amorphous silicon microbolometers with a pixel-pitch of 25 μm, integrated into a LCC TEC-less package. This detector has been specifically designed for large volume production, while keeping the main features of high end developments, at detection pixel level, as well as at ROIC level, like detector configuration by serial link in order to minimize the number of electrical inputs, low power, large dynamic range...) The main particular features of this achievement are the miniaturized very low weight package, along with easy TEC-less operation naturally afforded via the readout architecture, which leads to very low consumption levels, making it well adapted to low end hand held or helmet mounted thermal imaging cameras. We present in the last part of this paper the main electro-optical characteristics and TEC-less operation, demonstrating wide thermal dynamic range and low power, thanks to the simple single-level amorphous silicon technology, coupled with advanced ROIC design.

  9. Direct heat applications of geothermal energy in The Geysers/Clear Lake region. Volume I. Geotechnical assessment, agribusiness applications, socioeconomic assessment, engineering assessment. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1976-08-01

    Discussion is presented under the following section headings: background and some technical characteristics of geothermal resources; geology and geohydrology, geophysics, and, conclusions regarding availability of geothermal energy for nonelectric uses; agricultural assessment of Lake County, site assessment for potential agricultural development, analysis of potential agricultural applications, special application of low cost geothermal energy to algae harvesting, development of an integrated agribusiness, geothermal complex in Lake County, analysis of individual enterprises, and, recommendations for subsequent work; demographic characteristics, economic condition and perspective of Lake County, economic impact of geothermal in Lake County, social and economic factors related to geothermal resource development, socioeconomic impact of nonelectric uses of geothermal energy, and, identification of direct heat applications of geothermal energy for Lake County based on selected interviews; cost estimate procedure, example, justification of procedure, and, typical costs and conclusions; and, recommended prefeasibility and feasibility studies related to construction of facilities for nonelectric applications of geothermal resource utilization. (JGB)

  10. The Environment for Application Software Integration and Execution (EASIE) version 1.0. Volume 4: System installation and maintenance guide

    Science.gov (United States)

    Randall, Donald P.; Jones, Kennie H.; Rowell, Lawrence F.

    1988-01-01

    The Environment for Application Software Integration and Execution (EASIE) provides both a methodology and a set of software utility programs to ease the task of coordinating engineering design and analysis codes. This document provides necessary information for installing the EASIE software on a host computer system. The target host is a DEX VAX running VMS version 4; host dependencies are noted when appropriate. Relevant directories and individual files are identified, and compile/load/execute sequences are specified. In the case of the data management utilities, database management system (DBMS) specific features are described in an effort to assist the maintenance programmer in converting to a new DBMS. The document also describes a sample EASIE program directory structure to guide the program implementer in establishing his/her application dependent environment.

  11. Software design specification. Part 2: Orbital Flight Test (OFT) detailed design specification. Volume 3: Applications. Book 2: System management

    Science.gov (United States)

    1979-01-01

    The functions performed by the systems management (SM) application software are described along with the design employed to accomplish these functions. The operational sequences (OPS) control segments and the cyclic processes they control are defined. The SM specialist function control (SPEC) segments and the display controlled 'on-demand' processes that are invoked by either an OPS or SPEC control segment as a direct result of an item entry to a display are included. Each processing element in the SM application is described including an input/output table and a structured control flow diagram. The flow through the module and other information pertinent to that process and its interfaces to other processes are included.

  12. Thermal power systems: Small Power Systems Applications Project. Volume II. Detailed report. Annual technical report, fiscal year 1978

    Energy Technology Data Exchange (ETDEWEB)

    1979-01-15

    Small Power Systems Applications activities for FY 1978 are reported. Studies were conducted to address current small power system technology as applied to power plants up to 10 MWe in size. Markets for small power systems were characterized and cost goals were established for the project. Candidate power plant system design concepts were selected for evaluation and preliminary performance and cost assessments were made. Economic studies were conducted at JPL and under contract to Burns and McDonnell. Breakeven capital costs were determined for leading contenders among the candidate systems. An applications study was made of the potential use of small power systems in providing part of the demand for pumping power by the extensive aqueduct system of California, estimated to be 1000 MWe by 1985. Criteria and methodologies were developed for application to the ranking of candidate power plant system design concepts. Experimental power plants concepts of 1 MWe rating were studied by three contractors as a Phase I effort leading toward the definition of a power plant configuration for subsequent detail design, construction, testing and evaluation as Engineering Experiment No. 1 (EE No. 1). Site selection criteria and ground rules for the solicitation of EE No. 1 site participation proposals by DOE were developed.

  13. Interim report on the development and application of environmental mapped data digitization, encoding, analysis, and display software for the ALICE system. Volume II. [MAP, CHAIN, FIX, and DOUT, in FORTRAN IV for PDP-10

    Energy Technology Data Exchange (ETDEWEB)

    Amiot, L.W.; Lima, R.J.; Scholbrock, S.D.; Shelman, C.B.; Wehman, R.H.

    1979-06-01

    Volume I of An Interim Report on the Development and Application of Environmental Mapped Data Digitization, Encoding, Analysis, and Display Software for the ALICE System provided an overall description of the software developed for the ALICE System and presented an example of its application. The scope of the information presented in Volume I was directed both to the users and developers of digitization, encoding, analysis, and display software. Volume II presents information which is directly related to the actual computer code and operational characteristics (keys and subroutines) of the software. Volume II will be of more interest to developers of software than to users of the software. However, developers of software should be aware that the code developed for the ALICE System operates in an environment where much of the peripheral hardware to the PDP-10 is ANL/AMD built. For this reason, portions of the code may have to be modified for implementation on other computer system configurations. 11 tables.

  14. Aerial ultra-low-volume application of naled: impact on nontarget imperiled butterfly larvae (Cyclargus thomasi bethunebakeri) and efficacy against adult mosquitoes (Aedes taeniorhynchus).

    Science.gov (United States)

    Zhong, H; Hribar, L J; Daniels, J C; Feken, M A; Brock, C; Trager, M D

    2010-12-01

    We assessed the exposure and acute toxicity of naled, applied aerially as an ultra-low-volume spray for mosquito control, on late instar larvae of the Miami blue (Cyclargus thomasi bethunebakeri) (Comstock and Huntington 1943) (Lepidoptera: Lycaenidae), an imperiled South Florida butterfly. We concurrently evaluated the control efficacy against caged adult female salt-marsh mosquitoes (Aedes taeniorhynchus) (Wiedemann 1821) (Diptera: Culicidae). This 3-yr study was conducted in north Key Largo (Monroe County, FL) beginning in 2006. The field trials incorporated 15 sampling stations: nine in the target spray zone, three in the spray drift zone at varying distances from the target zone, and three in the control zone not subjected to naled spray drift. A total of six field spray trials were completed, three at an altitude of 30.5 m (100 feet), and three at 45.7 m (150 feet). For all trials, the ultra-low-volume application of Trumpet EC insecticide (78% naled) at a rate of 54.8 ml/ha (0.75 fl. oz/acre) was effective in killing caged adult mosquitoes in the target zone. Butterfly larvae survival was significantly reduced in the spray zone compared with drift and control zones. Analysis of insecticide residue data revealed that the mortality of the late instar butterfly larvae was a result of exposure to excess residues of naled. Additional research is needed to determine mitigation strategies that can limit exposure of sensitive butterflies to naled while maintaining mosquito control efficacy. PMID:22182563

  15. Application analysis of solar total energy systems to the residential sector. Volume III, conceptual design. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1979-07-01

    The objective of the work described in this volume was to conceptualize suitable designs for solar total energy systems for the following residential market segments: single-family detached homes, single-family attached units (townhouses), low-rise apartments, and high-rise apartments. Conceptual designs for the total energy systems are based on parabolic trough collectors in conjunction with a 100 kWe organic Rankine cycle heat engine or a flat-plate, water-cooled photovoltaic array. The ORC-based systems are designed to operate as either independent (stand alone) systems that burn fossil fuel for backup electricity or as systems that purchase electricity from a utility grid for electrical backup. The ORC designs are classified as (1) a high temperature system designed to operate at 600/sup 0/F and (2) a low temperature system designed to operate at 300/sup 0/F. The 600/sup 0/F ORC system that purchases grid electricity as backup utilizes the thermal tracking principle and the 300/sup 0/F ORC system tracks the combined thermal and electrical loads. Reject heat from the condenser supplies thermal energy for heating and cooling. All of the ORC systems utilize fossil fuel boilers to supply backup thermal energy to both the primary (electrical generating) cycle and the secondary (thermal) cycle. Space heating is supplied by a central hot water (hydronic) system and a central absorption chiller supplies the space cooling loads. A central hot water system supplies domestic hot water. The photovoltaic system uses a central electrical vapor compression air conditioning system for space cooling, with space heating and domestic hot water provided by reject heat from the water-cooled array. All of the systems incorporate low temperature thermal storage (based on water as the storage medium) and lead--acid battery storage for electricity; in addition, the 600/sup 0/F ORC system uses a therminol-rock high temperature storage for the primary cycle. (WHK)

  16. Application analysis of solar total energy systems to the residential sector. Volume IV, market penetration. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1979-07-01

    This volume first describes the residential consumption of energy in each of the 11 STES regions by fuel type and end-use category. The current and projected costs and availability of fossil fuels and electricity for the STES regions are reported. Projections are made concerning residential building construction and the potential market for residential STES. The effects of STES ownership options, institutional constraints, and possible government actions on market penetration potential were considered. Capital costs for two types of STES were determined, those based on organic Rankine cycle (ORC) heat engines and those based on flat plate, water-cooled photovoltaic arrays. Both types of systems utilized parabolic trough collectors. The capital cost differential between conventional and STE systems was calculated on an incremental cost per dwelling unit for comparison with projected fuel savings in the market penetration analysis. The market penetration analysis was planned in two phases, a preliminary analysis of each of the geographical regions for each of the STE systems considered; and a final, more precise analysis of those regions and systems showing promise of significant market penetration. However, the preliminary analysis revealed no geographical regions in which any of the STES considered promised to be competitive with conventional energy systems using utility services at the prices projected for future energy supplies in the residential market. Because no promising situations were found, the analysis was directed toward an examination of the parameters involved in an effort to identify those factors which make a residential STES less attractive than similar systems in the commercial and industrial areas. Results are reported. (WHK)

  17. Development and application of a risk assessment method for radioactive waste management. Volume III. Economic analysis; description and implementation of AMRAW-B model

    International Nuclear Information System (INIS)

    A Radioactive Waste Management Systems Model, is presented. The systems model and associated computer code called AMRAW (Assessment Method for Radioactive Waste), has two parts. The first part, AMRAW-A, consists of the Source Term (radioactive inventory versus time), the Release Model, and the Environmental Model. The second part of the systems model, AMRAW-B, is the Economic Model which calculates health effects corresponding to the various organ dose rates from AMRAW-A, collects these health effects in terms of economic costs and attributes these costs to radionuclides, decay groups, and elements initially in the waste inventory. This volume describes AMRAW-B, the Economics Model, and is in two parts: Part 1 presents a generic description of the AMRAW-B model, background economic theory and a description of the AMRAW-B computer code, and Part 2 presents implementation of the model with an application to terminal storage in a bedded salt reference repository

  18. 1993 RCRA Part B permit renewal application, Savannah River Site: Volume 10, Consolidated Incineration Facility, Section C, Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    Molen, G.

    1993-08-01

    This section describes the chemical and physical nature of the RCRA regulated hazardous wastes to be handled, stored, and incinerated at the Consolidated Incineration Facility (CIF) at the Savannah River Site. It is in accordance with requirements of South Carolina Hazardous Waste Management Regulations R.61-79.264.13(a) and(b), and 270.14(b)(2). This application is for permit to store and teat these hazardous wastes as required for the operation of CIF. The permit is to cover the storage of hazardous waste in containers and of waste in six hazardous waste storage tanks. Treatment processes include incineration, solidification of ash, and neutralization of scrubber blowdown.

  19. Direct heat applications of geothermal energy in The Geysers/Clear Lake region. Volume I. Geotechnical assessment, agribusiness applications, socioeconomic assessment, engineering assessment. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1977-08-01

    The different uses to which geothermal heat and fluids could be applied as a direct utilization of resource or as heat utilization are explored. The following aspects are covered: geotechnical assessment, agricultural and industrial applications, socioeconomic assessment, and engineering assessment. (MHR)

  20. Conceptual design of thermal energy storage systems for near term electric utility applications. Volume 1: Screening of concepts

    Science.gov (United States)

    Hausz, W.; Berkowitz, B. J.; Hare, R. C.

    1978-01-01

    Over forty thermal energy storage (TES) concepts gathered from the literature and personal contacts were studied for their suitability for the electric utility application of storing energy off-peak discharge during peak hours. Twelve selections were derived from the concepts for screening; they used as storage media high temperature water (HTW), hot oil, molten salts, and packed beds of solids such as rock. HTW required pressure containment by prestressed cast-iron or concrete vessels, or lined underground cavities. Both steam generation from storage and feedwater heating from storage were studied. Four choices were made for further study during the project. Economic comparison by electric utility standard cost practices, and near-term availability (low technical risk) were principal criteria but suitability for utility use, conservation potential, and environmental hazards were considered.

  1. Guidebook for performance assessment parameters used in the Waste Isolation Pilot Plant compliance certification application. Volume 2: Appendices

    International Nuclear Information System (INIS)

    The Waste Isolation Pilot Plant (WIPP) Compliance Certification Application (CCA) Performance Assessment (PA) Parameter Database and its ties to supporting information evolved over the course of two years. When the CCA was submitted to the Environmental Protection Agency (EPA) in October 1996, information such as identification of parameter value or distribution source was documented using processes established by Sandia National Laboratories WIPP Quality Assurance Procedures. Reviewers later requested additional supporting documentation, links to supporting information, and/or clarification for many parameters. This guidebook is designed to document a pathway through the complex parameter process and help delineate flow paths to supporting information for all WIPP CCA parameters. In addition, this report is an aid for understanding how model parameters used in the WIPP CCA were developed and qualified. To trace the source information for a particular parameter, a dual-route system was established. The first route uses information from the Parameter Records package as it existed when the CCA calculations were run. The second route leads from the EPA Parameter Database to additional supporting information

  2. Application of ICRP Radiation Protection Principles in Existing Exposure Situations with Large Volumes of NORM: The Wismut Case Study

    International Nuclear Information System (INIS)

    An outstanding example of an existing exposure situation resulting from large scale uranium mining and processing is the Wismut legacy in eastern Germany. From 1946 to 1990, the Soviet–German stock company SDAG WISMUT produced 216 000 t of uranium and thus became the world’s fourth largest uranium producer at that time. Due to the mining of low grade ore, about 800 million t of NORM residues (also referred to as low level radioactive waste) were deposited at the sites and an area of about 10 000 km2 became seriously affected and devastated. Mining and mineral processing took place in a densely populated area, whereby radioactive waste rock piles and tailings management facilities were placed close to residential areas. In such an existing exposure situation, the application of the International Commission on Radiological Protection key radiation protection principles has to meet site specific conditions and requires remedial measures which are far from standard solutions. This is illustrated in the paper. Approaches to decisions on justification of remedial activities are presented together with a description of the optimization process. (author)

  3. Guidebook for performance assessment parameters used in the Waste Isolation Pilot Plant compliance certification application. Volume 2: Appendices

    Energy Technology Data Exchange (ETDEWEB)

    Howarth, S.M.; Martell, M.A.; Weiner, R. [Sandia National Labs., Albuquerque, NM (United States); Lattier, C. [GRAM, Inc., Albuquerque, NM (United States)

    1998-06-01

    The Waste Isolation Pilot Plant (WIPP) Compliance Certification Application (CCA) Performance Assessment (PA) Parameter Database and its ties to supporting information evolved over the course of two years. When the CCA was submitted to the Environmental Protection Agency (EPA) in October 1996, information such as identification of parameter value or distribution source was documented using processes established by Sandia National Laboratories WIPP Quality Assurance Procedures. Reviewers later requested additional supporting documentation, links to supporting information, and/or clarification for many parameters. This guidebook is designed to document a pathway through the complex parameter process and help delineate flow paths to supporting information for all WIPP CCA parameters. In addition, this report is an aid for understanding how model parameters used in the WIPP CCA were developed and qualified. To trace the source information for a particular parameter, a dual-route system was established. The first route uses information from the Parameter Records package as it existed when the CCA calculations were run. The second route leads from the EPA Parameter Database to additional supporting information.

  4. Report on the ANSTO application for a licence to construct a Replacement Research Reactor, addressing seismic analysis and seismic design accident analysis, spent fuel and radioactive wastes

    International Nuclear Information System (INIS)

    The Report of the Nuclear Safety Committee (NSC) covers specific terms of reference as requested by the Chief Executive Officer of ARPANSA. The primary issue for the Working Group(WG) consideration was whether ANSTO had demonstrated: (i) that the overall approach to seismic analysis and its implementation in the design is both conservative and consistent with the international best practice; (ii) whether the full accident analysis in the Probabilistic Safety Assesment Report (PSAR) satisfies the radiation dose/frequency criteria specified in ARPANSA's regulatory assessment principle 28 and the assumptions used in the Reference Accident for the siting assessment have been accounted for in the PSAR; and (iii) the adequacy of the strategies for managing the spent fuel as proposed to be used in the Replacement Research Reactor and other radioactive waste (including emissions, taking into account the ALARA criterion) arising from the operation of the proposed replacement reactor and radioisotope production. The report includes a series of questions that were asked of the Applicant in the course of working group deliberations, to illustrate the breadth of inquiries that were made. The Committee noted that replies to some questions remain outstanding at the date of this document. The NSC makes a number of recommendations that appear in each section of the document, which has been compiled in three parts representing the work of each group. The NSC notes some lack of clarity in what was needed to be considered at this approval stage of the project, as against information that would be required at a later stage. While not in the original work plan, recent events of September 11, 2001 also necessitated some exploration of issues relating to construction security. Copyright (2002) Commonwealth of Australia

  5. Demonstration project as a procedure for accelerating the application of new technology (Charpie Task Force report). Volume II

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-02-01

    This report examines the issues associated with government programs proposed for the ''commercialization'' of new energy technologies; these programs are intended to hasten the pace at which target technologies are adopted by the private sector. The ''commercial demonstration'' is the principal tool used in these programs. Most previous government interventions in support of technological change have focused on R and D and left to the private sector the decision as to adoption for commercial utilization; thus there is relatively little in the way of analysis or experience which bears direct application. The analysis is divided into four sections. First, the role of R, D, and D within the structure of the national energy goals and policies is examined. The issue of ''prices versus gaps'' is described as a crucial difference of viewpoint concerning the role of the government in the future of the energy system. Second, the process of technological change as it occurs with respect to energy technologies is then examined for possible sources of misalignment of social and private incentives. The process is described as a series of investments. Third, correction of these sources of misalignment then becomes the goal of commercial demonstration programs as this goal and the means for attaining it are explored. Government-supported commercialization may be viewed as a subsidy to the introduction stage of the process; the circumstances under which such subsidies are likely to affect the success of the subsequent diffusion stage are addressed. The discussion then turns to the political, legal, and institutional problems. Finally, methods for evaluation and planning of commercial demonstration programs are analyzed. The critical areas of ignorance are highlighted and comprise a research agenda for improved analytical techniques to support decisions in this area.

  6. Application of a low-angle light scattering technique to cell volume and cell signaling studies on Ehrlich ascite tumor cells

    OpenAIRE

    Zinchenko, Valeriy P.; Lee, Vyacheslav V.; Berezhnov, Alexey V.; Mindukshev, Igor V.; Jenkins, Richard O; Goncharov, Nikolay V.

    2006-01-01

    A method for studying cells based on low-angle light scattering was applied to cell volume and cell signaling studies on Ehrlich ascite tumor cells (EATC). Changes in the volume of EATC were measured in hypotonic medium, as well as after activation with exogenous ATP, ionomycin and thimerosal. Increase of [Ca2+]i under ATP and ionomycin action induced reversible changes of cell volume: fast shrinking was followed by swelling. Thimerosal caused a reversible change in EATC volume with high ampl...

  7. Application of the Price-Volume Approach in Cases of Innovative Drugs Where Value-Based Pricing is Inadequate: Description of Real Experiences in Italy.

    Science.gov (United States)

    Messori, Andrea

    2016-08-01

    Several cases of expensive drugs designed for large patient populations (e.g. sofosbuvir) have raised a complex question in terms of drug pricing. Even assuming value-based pricing, the treatment with these drugs of all eligible patients would have an immense budgetary impact, which is unsustainable also for the richest countries. This raises the need to reduce the prices of these agents in comparison with those suggested by the value-based approach and to devise new pricing methods that can achieve this goal. The present study discusses in detail the following two methods: (i) The approach based on setting nation-wide budget thresholds for individual innovative agents in which a fixed proportion of the historical pharmaceutical expenditure represents the maximum budget attributable to an innovative treatment; (ii) The approach based on nation-wide price-volume agreements in which drug prices are progressively reduced as more patients receive the treatment. The first approach has been developed in the USA by the Institute for Clinical and Economic Review and has been applied to PCSK9 inhibitors (alirocumab and evolocumab). The second approach has been designed for the Italian market and has found a systematic application to manage the price of ranibizumab, sofosbuvir, and PCSK9 inhibitors. While, in the past, price-volume agreements have been applied only on an empirical basis (i.e. in the absence of any quantitative theoretical rule), more recently some explicit mathematical models have been described. The performance of these models is now being evaluated on the basis of the real-world experiences conducted in some European countries, especially Italy. PMID:27216427

  8. Minimizing the impact of the mosquito adulticide naled on honey bees, Apis mellifera (Hymenoptera: Apidae): aerial ultra-low-volume application using a high-pressure nozzle system.

    Science.gov (United States)

    Zhong, He; Latham, Mark; Payne, Steve; Brock, Cate

    2004-02-01

    The impact of the mosquito adulticide naled on honey bees, Apis mellifera L., was evaluated by exposing test beehives to nighttime aerial ultra-low-volume (ULV) applications using a high-pressure nozzle system. The tests were conducted during routine mosquito control missions at Manatee County, Florida, in summer 2000. Two treatment sites were sprayed a total of four times over a 10-wk period. Honey bees, which clustered outside of the hive entrances, were subjected to naled exposure during these mosquito control sprays. The highest average naled ground deposition was 2,688 microg/m2 at the Port Manatee site, which resulted in statistically significant bee mortality (118) compared with the controls. At the Terra Ceia Road site, an intermediate level of naled deposition was found (1,435 microg/m2). For this spray mission, the range of dead bees per hive at Terra Ceia was 2 to 9 before spraying and 5 to 36 after naled application. Means of all other naled ground depositions were 100 dead bees) resulted when naled residue levels were > 2,000 kg/m2 and honey bees were clustered outside of the hive entrances during mosquito adulticide applications. Compared with the flat-fan nozzle systems currently used by most of Florida's mosquito control programs, the high-pressure nozzle system used in this experiment substantially reduced environmental insecticide contamination and lead to decreased bee mortality. Statistical analysis also showed that average honey yield at the end of the season was not significantly reduced for those hives that were exposed to the insecticide. PMID:14998120

  9. Research on Application of Four-parameter Cylinder-volume-ratio Stem Profile%四参数柱干比曲线式应用研究

    Institute of Scientific and Technical Information of China (English)

    孟宪法; 李悦黎; 张方秋

    2001-01-01

    The study involved estimating stem volume, calculating merchantable vo lume yielding rate and timber assortments volume with four-parameter cylinder- vo lume-ratio stem profile. The result shows it performs better than Schumarher-H all at estimating stem volume when the data from Quercus aliena we re classified by cla ss. Compared with taper function at calculating merchantable volume yielding rat e, four-parameter cylinder-volume-ratio stem profile also performs well with sys tematic error below 1% and mean square error below 5%. To Pinus tabu laeformis tr ees, taper function has better accuracy degree than cylinder-volume-rati o method , but the result is contrary to Q.aliena. When calculating t imber assortments vo lume with four-parameter cylinder-volume-ratio method, systematic error is be low 6% and mean square error below 19%.

  10. SHADOW MAPPING OR SHADOW VOLUME?

    Directory of Open Access Journals (Sweden)

    Hoshang Kolivand

    2011-01-01

    Full Text Available In this paper two techniques of shadow generation are described. Volume shadow is geometric base but shadow mapping is image base. Silhouette detection is a most expensive step to create volume shadow. Two algorithms to recognize silhouette are introduced. Stencil buffer and Z- buffer are two other tools for creating shadow by volume shadow technique. Both algorithms are implemented in virtual environment with moveable light source. Triangular method and the Visible-non visible method are introduced. The recent traditional silhouette detection and implementation techniques used in volume shadow algorithm are improved. With introduce flowchart of both algorithms, the last volume shadow algorithm using stencil buffer is rewritten. A very simple algorithm to create volume shadow is proposed. The last shadow mapping algorithm is rewritten. These techniques are poised to bring realism into commercial games. It may be use in virtual reality applications.

  11. Aplicação da análise custo/volume/lucro em pequena indústria de laticínios = Application of a cost/volume/profit analysis in a small industry of dairy products

    Directory of Open Access Journals (Sweden)

    Rodney Wernke

    2008-11-01

    Full Text Available Relata estudo de caso em que foi aplicada a Análise Custo/Volume/Lucro como instrumento de avaliação do desempenho de uma pequena indústria. Inicialmente foi efetuada uma revisão bibliográfica sobre os conceitos utilizados, especialmente margem de contribuição, ponto de equilíbrio e margem de segurança. Em seguida, descreveu-se o contexto da empresa pesquisada, mostrando suas principais características. Posteriormente foram apresentadas as etapas seguidas para aplicação da Análise Custo/Volume/Lucro. Foram demonstrados os cálculos efetuados e comentados os resultados oriundos mais relevantes para a administração da organização enfocada pelo estudo. Por último, foram elencadas as informações gerenciais obtidas, ressaltadas as limitações inerentes à ferramenta utilizada e sugerido tema para trabalhos futuros.This article reports a study case in which a Cost/Volume/Profit Analysis was applied asa tool to evaluate the performance of a small industry of dairy products. At first, abibliographic revision of the concepts was made, especially contribution margin, balancedpoint and security margin. After, the context of the industry was described, showing itsmain characteristics. After that, the steps which were followed so that the Cost/Volume/Profit Analysis was applied were presented, the calculi made were demonstrated andthe most relevant results from this study were commented for the industry management.Finally, the managerial information obtained was listed; emphasizing the limitations ofthe tool which was used and a theme for further research was suggested.

  12. Renormalized Volume

    CERN Document Server

    Gover, A Rod

    2016-01-01

    For any conformally compact manifold with hypersurface boundary we define a canonical renormalized volume functional and compute an explicit, holographic formula for the corresponding anomaly. For the special case of asymptotically Einstein manifolds, our method recovers the known results. The anomaly does not depend on any particular choice of regulator, but the coefficients of divergences do. We give explicit formulae for these divergences valid for any choice of regulating hypersurface; these should be relevant to recent studies of quantum corrections to entanglement entropies. The anomaly is expressed as a conformally invariant integral of a local Q-curvature that generalizes the Branson Q-curvature by including data of the embedding. In each dimension this canonically defines a higher dimensional generalization of the Willmore energy/rigid string action. We show that the variation of these energy functionals is exactly the obstruction to solving a singular Yamabe type problem with boundary data along the...

  13. Data catalog series for space science and applications flight missions. Volume 5A: Descriptions of astronomy, astrophysics, and solar physics spacecraft and investigations. Volume 5B: Descriptions of data sets from astronomy, astrophysics, and solar physics spacecraft and investigations

    Science.gov (United States)

    Kim, Sang J. (Editor)

    1988-01-01

    The main purpose of the data catalog series is to provide descriptive references to data generated by space science flight missions. The data sets described include all of the actual holdings of the Space Science Data Center (NSSDC), all data sets for which direct contact information is available, and some data collections held and serviced by foreign investigators, NASA and other U.S. government agencies. This volume contains narrative descriptions of data sets of astronomy, astrophysics, solar physics spacecraft and investigations. The following spacecraft series are included: Mariner, Pioneer, Pioneer Venus, Venera, Viking, Voyager, and Helios. Separate indexes to the planetary and interplanetary missions are also provided.

  14. On algebraic volume density property

    OpenAIRE

    Kaliman, Shulim; Kutzschebauch, Frank

    2012-01-01

    A smooth affine algebraic variety $X$ equipped with an algebraic volume form $\\omega$ has the algebraic volume density property (AVDP) if the Lie algebra generated by completely integrable algebraic vector fields of $\\omega$-divergence zero coincides with the space of all algebraic vector fields of $\\omega$-divergence zero. We develop an effective criterion of verifying whether a given $X$ has AVDP. As an application of this method we establish AVDP for any homogeneous space $X=G/R$ that admi...

  15. Environmental Assessment - Proposed Application of Aerially Applied Ultra Low Volume Naled for the Control of Adult Mosquitoes within the Big Branch Marsh National Wildlife Refuge in Lacombe, Louisiana

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This document assesses the effects that aerially applied ultra low volume Naled would have on adult mosquito populations. It also offers alternatives.

  16. Effective mode volumes for leaky optical cavities

    DEFF Research Database (Denmark)

    Kristensen, Philip Trøst; Van Vlack, Cole; Hughes, Stephen

    2011-01-01

    definition of an effective mode volume is ambiguous and not applicable. Instead, we propose an alternative effective mode volume which can be easily evaluated based on the mode calculation methods typically applied in the literature and which is directly applicable to a much wider range of physical systems....

  17. Double-echo perfusion-weighted MR imaging: basic concepts and application in brain tumors for the assessment of tumor blood volume and vascular permeability

    OpenAIRE

    Uematsu, Hidemasa; Maeda, Masayuki

    2006-01-01

    Perfusion-weighted magnetic resonance (MR) imaging using contrast agents plays a key role in characterizing tumors of the brain. We have shown that double-echo perfusion-weighted MR imaging (DEPWI) is potentially useful in assessing brain tumors. Quantitative indices, such as tumor blood volume, are obtained using DEPWI, which allows correction of underestimation of tumor blood volume due to leakage of contrast agents from tumor vessels, in addition to simultaneous acquisition of tumor vessel...

  18. Slice-to-volume registration and its potential application to interventional MRI-guided radio-frequency thermal ablation of prostate cancer.

    Science.gov (United States)

    Fei, Baowei; Duerk, Jeffrey L; Boll, Daniel T; Lewin, Jonathan S; Wilson, David L

    2003-04-01

    In this study, we registered live-time interventional magnetic resonance imaging (iMRI) slices with a previously obtained high-resolution MRI volume that in turn can be registered with a variety of functional images, e.g., PET, SPECT, for tumor targeting. We created and evaluated a slice-to-volume (SV) registration algorithm with special features for its potential use in iMRI-guided radio-frequency (RF) thermal ablation of prostate cancer. The algorithm features included a multiresolution approach, two similarity measures, and automatic restarting to avoid local minima. Imaging experiments were performed on volunteers using a conventional 1.5-T MR scanner and a clinical 0.2-T C-arm iMRI system under realistic conditions. Both high-resolution MR volumes and actual iMRI image slices were acquired from the same volunteers. Actual and simulated iMRI images were used to test the dependence of SV registration on image noise, receive coil inhomogeneity, and RF needle artifacts. To quantitatively assess registration, we calculated the mean voxel displacement over a volume of interest between SV registration and volume-to-volume registration, which was previously shown to be quite accurate. More than 800 registration experiments were performed. For transverse image slices covering the prostate, the SV registration algorithm was 100% successful with an error of bladder filling. These preliminary experiments indicate that MR SV registration is sufficiently accurate to aid image-guided therapy.

  19. LETTER TO THE EDITOR: Volume-controlled buckling of thin elastic shells: application to crusts formed on evaporating partially wetted droplets

    Science.gov (United States)

    Head, D. A.

    2006-10-01

    Motivated by observing the buckling of glassy crusts formed on evaporating droplets of polymer and colloid solutions, we numerically model the deformation and buckling of spherical elastic caps controlled by varying the volume between the shell and the substrate. This volume constraint mimics the incompressibility of the unevaporated solvent. Discontinuous buckling is found to occur for sufficiently thin and/or large contact angle shells, and robustly takes the form of a single circular region near the boundary that 'snaps' to an inverted shape, in contrast to the externally pressurized shells case. Scaling theory for shallow shells is shown to approximate well the critical buckling volume, the subsequent enlargement of the inverted region and the contact line force.

  20. Ajuste do modelo de Schumacher e Hall e aplicação de redes neurais artificiais para estimar volume de árvores de eucalipto Adjustment of the Schumacher and Hall model and application of artificial neural networks to estimate volume of eucalypt trees

    Directory of Open Access Journals (Sweden)

    Mayra Luiza Marques da Silva

    2009-12-01

    Full Text Available Objetivou-se, neste trabalho, avaliar o ajuste do modelo volumétrico de Schumacher e Hall por diferentes algoritmos, bem como a aplicação de redes neurais artificiais para estimação do volume de madeira de eucalipto em função do diâmetro a 1,30 m do solo (DAP, da altura total (Ht e do clone. Foram utilizadas 21 cubagens de povoamentos de clones de eucalipto com DAP variando de 4,5 a 28,3 cm e altura total de 6,6 a 33,8 m, num total de 862 árvores. O modelo volumétrico de Schumacher e Hall foi ajustado nas formas linear e não linear, com os seguintes algoritmos: Gauss-Newton, Quasi-Newton, Levenberg-Marquardt, Simplex, Hooke-Jeeves Pattern, Rosenbrock Pattern, Simplex, Hooke-Jeeves e Rosenbrock, utilizado simultaneamente com o método Quasi-Newton e com o princípio da Máxima Verossimilhança. Diferentes arquiteturas e modelos (Multilayer Perceptron MLP e Radial Basis Function RBF de redes neurais artificiais foram testados, sendo selecionadas as redes que melhor representaram os dados. As estimativas dos volumes foram avaliadas por gráficos de volume estimado em função do volume observado e pelo teste estatístico L&O. Assim, conclui-se que o ajuste do modelo de Schumacher e Hall pode ser usado na sua forma linear, com boa representatividade e sem apresentar tendenciosidade; os algoritmos Gauss-Newton, Quasi-Newton e Levenberg-Marquardt mostraram-se eficientes para o ajuste do modelo volumétrico de Schumacher e Hall, e as redes neurais artificiais apresentaram boa adequação ao problema, sendo elas altamente recomendadas para realizar prognose da produção de florestas plantadas.This research aimed at evaluating the adjustment of Schumacher and Hall volumetric model by different algorithms and the application of artificial neural networks to estimate the volume of wood of eucalyptus according to the diameter at breast height (DBH, total height (Ht of the clone. For such, 21 scalings of stands of eucalyptus clones were used with

  1. Development and application of a volume penalization immersed boundary method for the computation of blood flow and shear stresses in cerebral vessels and aneurysms

    NARCIS (Netherlands)

    Mikhal, Julia; Geurts, Bernard J.

    2013-01-01

    A volume-penalizing immersed boundary method is presented for the simulation of laminar incompressible flow inside geometrically complex blood vessels in the human brain. We concentrate on cerebral aneurysms and compute flow in curved brain vessels with and without spherical aneurysm cavities attach

  2. Targeting Cydia pomonella (L.)(Lepidoptera: Tortricidae) Adults with Low Volume Applications of Insecticides Alone and in Combination with Sex Pheromone

    Science.gov (United States)

    Studies examined the effectiveness of adding insecticides to low volume sprays of a microencapsulated (MEC) sex pheromone to manage codling moth, Cydia pomonella (L). The activities of fifteen insecticides against the adult stage were first evaluated with a plastic cup assay. In general, moth longev...

  3. Resource Conservation and Recovery Act: Part B, Permit application [for the Waste Isolation Pilot Plant (WIPP)]. Volume 1, Revison 1.0

    Energy Technology Data Exchange (ETDEWEB)

    1992-03-01

    This report contains information related to the permit application for the WIPP facility. Information is presented on solid waste management; personnel safety; emergency plans; site characterization; applicable regulations; decommissioning; and ground water monitoring requirements.

  4. A method to estimate the fractional fat volume within a ROI of a breast biopsy for WAXS applications: Animal tissue evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Tang, Robert Y., E-mail: rx-tang@laurentian.ca [Biomolecular Sciences Program, Laurentian University, 935 Ramsey Lake Road, Sudbury, Ontario P3E 2C6 (Canada); McDonald, Nancy, E-mail: mcdnancye@gmail.com; Laamanen, Curtis, E-mail: cx-laamanen@laurentian.ca [Department of Physics, Laurentian University, 935 Ramsey Lake Road, Sudbury, Ontario P3E 2C6 (Canada); LeClair, Robert J., E-mail: rleclair@laurentian.ca [Department of Physics, Laurentian University, 935 Ramsey Lake Road, Sudbury, Ontario P3E 2C6, Canada and Biomolecular Sciences Program, Laurentian University, 935 Ramsey Lake Road, Sudbury, Ontario P3E 2C6 (Canada)

    2014-11-01

    Purpose: To develop a method to estimate the mean fractional volume of fat (ν{sup ¯}{sub fat}) within a region of interest (ROI) of a tissue sample for wide-angle x-ray scatter (WAXS) applications. A scatter signal from the ROI was obtained and use of ν{sup ¯}{sub fat} in a WAXS fat subtraction model provided a way to estimate the differential linear scattering coefficient μ{sub s} of the remaining fatless tissue. Methods: The efficacy of the method was tested using animal tissue from a local butcher shop. Formalin fixed samples, 5 mm in diameter 4 mm thick, were prepared. The two main tissue types were fat and meat (fibrous). Pure as well as composite samples consisting of a mixture of the two tissue types were analyzed. For the latter samples, ν{sub fat} for the tissue columns of interest were extracted from corresponding pixels in CCD digital x-ray images using a calibration curve. The means ν{sup ¯}{sub fat} were then calculated for use in a WAXS fat subtraction model. For the WAXS measurements, the samples were interrogated with a 2.7 mm diameter 50 kV beam and the 6° scattered photons were detected with a CdTe detector subtending a solid angle of 7.75 × 10{sup −5} sr. Using the scatter spectrum, an estimate of the incident spectrum, and a scatter model, μ{sub s} was determined for the tissue in the ROI. For the composite samples, a WAXS fat subtraction model was used to estimate the μ{sub s} of the fibrous tissue in the ROI. This signal was compared to μ{sub s} of fibrous tissue obtained using a pure fibrous sample. Results: For chicken and beef composites, ν{sup ¯}{sub fat}=0.33±0.05 and 0.32 ± 0.05, respectively. The subtractions of these fat components from the WAXS composite signals provided estimates of μ{sub s} for chicken and beef fibrous tissue. The differences between the estimates and μ{sub s} of fibrous obtained with a pure sample were calculated as a function of the momentum transfer x. A t-test showed that the mean of the

  5. A method to estimate the fractional fat volume within a ROI of a breast biopsy for WAXS applications: Animal tissue evaluation

    International Nuclear Information System (INIS)

    Purpose: To develop a method to estimate the mean fractional volume of fat (ν¯fat) within a region of interest (ROI) of a tissue sample for wide-angle x-ray scatter (WAXS) applications. A scatter signal from the ROI was obtained and use of ν¯fat in a WAXS fat subtraction model provided a way to estimate the differential linear scattering coefficient μs of the remaining fatless tissue. Methods: The efficacy of the method was tested using animal tissue from a local butcher shop. Formalin fixed samples, 5 mm in diameter 4 mm thick, were prepared. The two main tissue types were fat and meat (fibrous). Pure as well as composite samples consisting of a mixture of the two tissue types were analyzed. For the latter samples, νfat for the tissue columns of interest were extracted from corresponding pixels in CCD digital x-ray images using a calibration curve. The means ν¯fat were then calculated for use in a WAXS fat subtraction model. For the WAXS measurements, the samples were interrogated with a 2.7 mm diameter 50 kV beam and the 6° scattered photons were detected with a CdTe detector subtending a solid angle of 7.75 × 10−5 sr. Using the scatter spectrum, an estimate of the incident spectrum, and a scatter model, μs was determined for the tissue in the ROI. For the composite samples, a WAXS fat subtraction model was used to estimate the μs of the fibrous tissue in the ROI. This signal was compared to μs of fibrous tissue obtained using a pure fibrous sample. Results: For chicken and beef composites, ν¯fat=0.33±0.05 and 0.32 ± 0.05, respectively. The subtractions of these fat components from the WAXS composite signals provided estimates of μs for chicken and beef fibrous tissue. The differences between the estimates and μs of fibrous obtained with a pure sample were calculated as a function of the momentum transfer x. A t-test showed that the mean of the differences did not vary from zero in a statistically significant way thereby validating the

  6. Twenty-fifth water reactor safety information meeting: Proceedings. Volume 1: Plenary sessions; Pressure vessel research; BWR strainer blockage and other generic safety issues; Environmentally assisted degradation of LWR components; Update on severe accident code improvements and applications

    International Nuclear Information System (INIS)

    This three-volume report contains papers presented at the conference. The papers are printed in the order of their presentation in each session and describe progress and results of programs in nuclear safety research conducted in this country and abroad. Foreign participation in the meeting included papers presented by researchers from France, Japan, Norway, and Russia. The titles of the papers and the names of the authors have been updated and may differ from those that appeared in the final program of the meeting. This volume contains the following information: (1) plenary sessions; (2) pressure vessel research; (3) BWR strainer blockage and other generic safety issues; (4) environmentally assisted degradation of LWR components; and (5) update on severe accident code improvements and applications. Selected papers have been indexed separately for inclusion in the Energy Science and Technology Database

  7. Modern Chemical Technology, Volume 5.

    Science.gov (United States)

    Pecsok, Robert L., Ed.; Chapman, Kenneth, Ed.

    This volume contains chapters 26-31 for the American Chemical Society (ACS) "Modern Chemical Technology" (ChemTeC) instructional material intended to prepare chemical technologists. Chapter 26 reviews oxidation and reduction, including applications in titrations with potassium permanganate and iodometry. Coordination compounds are described in the…

  8. 重度肺气肿的内镜下肺减容治疗技术%Application of endoscopic lung volume reduction technique in severe emphysema

    Institute of Scientific and Technical Information of China (English)

    迟晶; 郭述良; 贾晋伟; 李一诗

    2013-01-01

    慢性阻塞性肺病(chronic obstructive pulmonary diseases,COPD)在世界范围的发病率和死亡率占主要因素.COPD发展至重度肺气肿阶段时严重影响患者生活质量.内镜肺减容术(endoscopic lung volume reduction,ELVR)是通过支气管镜技术使过度充气的肺叶产生不张,疗效较传统的内科治疗更为确切,与外科肺减容术相比,ELVR以其微创,操作相对简单,并发症和死亡率降低等优点,引起了世界医学界的广泛研究.目前国内外研究较多的内镜下肺减容技术主要包括支气管内单向活瓣技术(one-way endobronchial valves,EBV)、气道旁路支架(airway bypass stents,ABS)、聚合物肺减容术(polymeric lung volume reduction,PLVR)、经支气管镜热蒸汽消融术(bronchoscopic thermal vapor ablation,BTVA)和肺减容弹簧圈(lung volume reduction coil,LVRC)等5种.本文将就上述内镜肺减容技术作一综述.%Chronic obstructive pulmonary disease (COPD) is a major cause of morbidity and mortality worldwide.Once the disease develops into severe emphysema,it seriously affects the patients' life quality.Endoscopic lung volume reduction(ELVR) with bronchoscopic techniques to bring about atelectasis of the hyperinflated lobe has been developed and studied widely over the past decade,because it has a better clinical effect than the traditional medicine treatment.The techniques have the advantages of minimally invasive and simple with less complications and lower mortality compared to the open surgical approach.Nowadays the most commonly used ELVR techniques include one-way endobronchial valves (EBV),airway bypass stents (ABS),polymeric lung volume reduction (PLVR),bronchoscopic thermal vapor ablation (BTVA) and lung volume reduction coil (LVRC).In this paper the ELVR techniques are reviewed.

  9. Fuzziness and medicine philosophical reflections and application systems in health care a companion volume to Sadegh-Zadeh’s handbook of analytical philosophy of medicine

    CERN Document Server

    Tabacchi, Marco

    2013-01-01

    This book is a collection of contributions written by philosophers and scientists active in different fields, such as mathematics, logics, social sciences, computer sciences and linguistics. They comment on and discuss various parts of and subjects and propositions introduced in the Handbook of Analytical Philosophy of Medicine from Kazem Sadegh-Zadeh, published by Springer in 2012. This volume reports on the fruitful exchange and debate that arose in the fuzzy community upon the publication of the Handbook. This was not only very much appreciated by the community but also seen as a critical starting point for beginning a new discussion. The results of this discussion, which involved many different perspectives from science and the humanities and was warmly encouraged by Kazem Sadegh-Zadeh himself, are accurately reported in this volume, which is intended to be a critical companion to Kazem Sadegh-Zadeh´s handbook.   Rudolf Seising is currently an adjoint researcher at the European Centre for Soft Computing...

  10. On the influence of local fluctuations in volume fraction of constituents on the effective properties of nonlinear composites. Application to porous materials

    Science.gov (United States)

    Gărăjeu, M.; Suquet, P.

    2007-04-01

    Composite materials often exhibit local fluctuations in the volume fraction of their individual constituents. This paper studies the influence of such small fluctuations on the effective properties of composites. A general asymptotic expansion of these properties in terms of powers of the amplitude of the fluctuations is given first. Then, this general result is applied to porous materials. As is well-known, the effective yield surface of ductile voided materials is accurately described by Gurson's criterion. Suitable extensions for viscoplastic solids have also been proposed. The question addressed in the present study pertains to nonuniform distributions of voids in a typical volume element or in other words to the presence of matrix-rich and pore-rich zones in the material. It is shown numerically and analytically that such deviations from a uniform distribution result in a weakening of the macroscopic carrying capacity of the material.

  11. Clinical application of a right ventricular pressure-volume loop determined by gated blood-pool imaging and simultaneously measured right ventricular pressure

    Energy Technology Data Exchange (ETDEWEB)

    Yasue, Takao; Watanabe, Sachiro; Sugishita, Nobuyoshi; Tanaka, Tsutomu; Yokoyama, Hideo (Prefectural Gifu Hospital (Japan))

    1983-09-01

    The data obtained by ECG-gated radionuclide angiography were collected simultaneously with right ventricular pressure and thermal cardiac output (CO) obtained by a Swan-Ganz catheter in Scintipac 1200 (Shimazu Co) in order to create a right ventricular pressure-volume (RV P-V) loop. Subjects consisted of 15 patients with old myocardial infarction (MI group), seven with angina pectoris (AP group), six with congestive cardiomyopathy (CCM group) and five with neurocirculatory asthenia (NCA group). Right ventricular end-diastolic volume (RVEDV) was calculated as RVEDV = CO/(EF x HR) (CO = cardiac output; HR = heart rate). Systolic work (W sub(S)), diastolic work (W sub(D)) and net work (W sub(N)) were calculated from a RV P-V loop by Simpson's method. The measurements were performed before and 5 min after sublingual administration of nitroglycerin (NG) (0.3 mg). The results were as follows: 1. RV P-V loops shifted towards the left lower part of the P-V plane after sublingual administration of nitroglycerin, indicating the reduction of pressure and volume of the right ventricle. 2. Right ventricular ejection fraction (RVEF) in the MI, AP and CCM groups showed smaller values than that of the NCA group. 3. Right ventricular end-diastolic volume index (RVEDVI) showed a converse relation with RVEF. 4. Cardiac index in all groups decreased after NG and a statistical significance was seen in the MI, AP and NCA groups (p<0.05). 5. RV W sub(S), RV W sub(D) and RV W sub(N) showed no difference among each groups in the control state, and significantly decreased after NG. We conclude that the present method using RV P-V loop might be useful as a noninvasive bedside monitoring and permits the evaluation of RV function in a clinical setting.

  12. Eleventh annual Department of Energy low-level waste management conference. Volume 3: Waste characterization, waste reduction and minimization, prototype licensing application

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-11-01

    Thirteen papers are presented in volume 3. The seven papers on waste characterization discuss sampling, analysis, and certification techniques for low-level radioactive wastes. Three papers discuss US DOE waste minimization policies and regulations, Y-12 Plant`s reduction of chlorinated solvents, and C-14 removal from spent resins. The last three papers discuss the licensing studies for earth-mounded concrete bunkers for LLW disposal. Papers have been processed separately for inclusion on the data base.

  13. The clinical application of 4D 18F-FDG PET/CT on gross tumor volume delineation for radiotherapy planning in esophageal squamous cell cancer

    OpenAIRE

    Wang, Yao-Ching; Hsieh, Te-Chun; Yu, Chun-Yen; Yen, Kuo-Yang; Chen, Shang-Wen; Yang, Shih-Neng; Chien, Chun-Ru; Hsu, Shih-Ming; Pan, Tinsu; Kao, Chia-Hung; Liang, Ji-An

    2012-01-01

    A combination of four-dimensional computed tomography with 18F-fluorodeoxyglucose positron emission tomography (4D CT-FDG PET) was used to delineate gross tumor volume (GTV) in esophageal cancer (EC). Eighteen patients with EC were prospectively enrolled. Using 4D images taken during the respiratory cycle, the average CT image phase was fused with the average FDG PET phase in order to analyze the optimal standardized uptake values (SUV) or threshold. PET-based GTV (GTVPET) was determined with...

  14. Clinical application of a right ventricular pressure-volume loop determined by gated blood-pool imaging and simultaneously measured right ventricular pressure

    International Nuclear Information System (INIS)

    The data obtained by ECG-gated radionuclide angiography were collected simultaneously with right ventricular pressure and thermal cardiac output (CO) obtained by a Swan-Ganz catheter in Scintipac 1200 (Shimazu Co) in order to create a right ventricular pressure-volume (RV P-V) loop. Subjects consisted of 15 patients with old myocardial infarction (MI group), seven with angina pectoris (AP group), six with congestive cardiomyopathy (CCM group) and five with neurocirculatory asthenia (NCA group). Right ventricular end-diastolic volume (RVEDV) was calculated as RVEDV = CO/(EF x HR) (CO = cardiac output; HR = heart rate). Systolic work (W sub(S)), diastolic work (W sub(D)) and net work (W sub(N)) were calculated from a RV P-V loop by Simpson's method. The measurements were performed before and 5 min after sublingual administration of nitroglycerin (NG) (0.3 mg). The results were as follows: 1. RV P-V loops shifted towards the left lower part of the P-V plane after sublingual administration of nitroglycerin, indicating the reduction of pressure and volume of the right ventricle. 2. Right ventricular ejection fraction (RVEF) in the MI, AP and CCM groups showed smaller values than that of the NCA group. 3. Right ventricular end-diastolic volume index (RVEDVI) showed a converse relation with RVEF. 4. Cardiac index in all groups decreased after NG and a statistical significance was seen in the MI, AP and NCA groups (p<0.05). 5. RV W sub(S), RV W sub(D) and RV W sub(N) showed no difference among each groups in the control state, and significantly decreased after NG. We conclude that the present method using RV P-V loop might be useful as a noninvasive bedside monitoring and permits the evaluation of RV function in a clinical setting

  15. 灰色预测模型在客运量预测中的应用%Application of Grey Forecast Model in Passenger Volume Forecast

    Institute of Scientific and Technical Information of China (English)

    顾央青

    2012-01-01

    Based on grey theory, the thesis established grey model GM(1,1) and took a forecasting test according to passenger volume data in Ningbo. The results showed a certain high forecasting precision, and proved the feasibility and effectiveness of this model in forecasting passenger volume. A future Ningbo's passenger volume from year 2010 to 2014 is forecasted on the basis of this research as well.%运用灰色理论,根据2000—2009年宁渡市客运量数据,建立灰色GM(1,1)预测模型并进行预测,结果表明预测精度较高.说明了该方法用于客运量预测的可行性和有效性.并在此基础上对2010~2014年的宁波市客运量作出预测。

  16. ICONE-4: Proceedings. Volume 2: Advanced reactors

    International Nuclear Information System (INIS)

    The proceedings for this conference are contained in 5 volumes. This volume is divided into the following areas: advanced reactor requirements; advanced reactor design and analysis; arrangement and construction; specific reactor designs; demonstration testing; safety systems and analysis; component demonstration testing; advanced reactor containment design; licensing topics and updates; accelerator applications and spallation sources; and advanced reactor development. Separate abstracts were prepared for most papers in this volume

  17. ICONE-4: Proceedings. Volume 3: Safety and reliability

    International Nuclear Information System (INIS)

    The proceedings of this conference are divided into five volumes. This volume is divided into the following sections: operation and maintenance; accident simulation and analysis; stability analysis; Korea Project -- safety analysis and radiation release; severe accident analysis; severe accident features; severe accident management; emerging risk-based PRA applications; PSA/PRA applications; PSA -- applications and procedures; PSA -- procedure and policy; dynamic PSA applications; and PSA -- policy and miscellaneous. Separate abstract were prepared for all papers in this volume

  18. LANDSAT-4 Science Characterization Early Results. Volume 4: Applications. [agriculture, soils land use, geology, hydrology, wetlands, water quality, biomass identification, and snow mapping

    Science.gov (United States)

    Barker, J. L. (Editor)

    1985-01-01

    The excellent quality of TM data allows researchers to proceed directly with applications analyses, without spending a significant amount of time applying various corrections to the data. The early results derived of TM data are discussed for the following applications: agriculture, land cover/land use, soils, geology, hydrology, wetlands biomass, water quality, and snow.

  19. Finite Volume Methods for Solving Electromagnetic Problems in Nonhomogeneous Media

    Institute of Scientific and Technical Information of China (English)

    Zou Jun

    2003-01-01

    This article shall review some of the recent advances on finite volume methods for solving electromagnetic problems in nonhomogeneous media. The stability, conver gence and applications of the finite volume methods will be discussed.

  20. Application for approval of derived authorized limits for the release of the 190-C trenches and 105-C process water tunnels at the Hanford Site: Volume 2 - Source term development

    International Nuclear Information System (INIS)

    As part of environmental restoration activities at the Hanford Site, Bechtel Hanford, Inc. (BHI) is conducting a series of evaluations to determine appropriate release conditions for specific facilities following the completion of decontamination and decommissioning (D and D) projects. The release conditions, with respect to the residual volumetric radioactive contamination, are termed authorized limits. This two volume report provides the necessary evaluations for the 290-C trenches and 105-C process water tunnels, and is intended to serve as the technical basis for a request for approval of authorized limits of residual radioactive contamination levels associated with these facilities. Volume 2 contains the Source Term Determination. This volume contains the radiological characterization data, spreadsheet analyses, and results of efforts to determine the radiological source terms. The source terms characterize the radionuclides and activity concentration levels for the facilities, and serves as input to the various radiation exposure pathways and scenarios used to estimate the individual radiation doses that could result from release of these facilities. Based on the results of these evaluations, it is determined that the application of the proposed authorized limits for the 190-C trenches and the 105-C process water tunnels represents a safe and cost-effective approach to their final disposition

  1. High Sensitivity RT-qPCR Assay of Nonlabeled siRNA in Small Blood Volume for Pharmacokinetic Studies: Application to Survivin siRNA.

    Science.gov (United States)

    Yeung, Bertrand Z; Lu, Ze; Wientjes, Guillaume M; Au, Jessie L-S

    2015-11-01

    RNAi therapeutics provide an opportunity to correct faulty genes, and several RNAi have entered clinical evaluation. The existing quantification methods typically use radioactivity- or fluorescence-labeled RNAi, require large blood volumes, and/or have a limited dynamic detection range. We established a quantitative reverse transcriptase real-time polymerase chain reaction (RT-qPCR) assay to measure RNAi; the model analyte was survivin siRNA (siSurvivin). A second siRNA was used as the internal standard. The three major steps were (a) extraction of the two siRNAs from blood or water, (b) synthesis of their cDNA by poly-A extension, and (c) qPCR of cDNA. Standard curves were established. Utility of the assay was demonstrated in a pharmacokinetic study where all 12 samples for the blood concentration-time profile were obtained from a single mouse given an intravenous dose of 1 nmole siSurvivin (prepared as lipoplex with pegylated cationic liposomes). The RT-qPCR assay was sensitive (lower detection limit of 100 fM) and had a 5 × 107-fold dynamic range and low sample volume requirement (10 μL). The 16-point standard curves constructed using whole blood samples were linear (R (2) > 0.98). The intraday and interday variations for the slopes were ≤6%, although the variations for accuracy and precision at individual concentrations were substantially higher (58-145%). Standard curves prepared with water in place of blood showed similar results (water may be used when blood is not available. The current RT-qPCR assay enabled the measurement of nonlabeled siRNA in small volume of blood samples. PMID:26286676

  2. Data catalog series for space science and applications flight missions. Volume 3B: Descriptions of data sets from low- and medium-altitude scientific spacecraft and investigations

    Science.gov (United States)

    Jackson, John E. (Editor); Horowitz, Richard (Editor)

    1986-01-01

    The main purpose of the data catalog series is to provide descriptive references to data generated by space science flight missions. The data sets described include all of the actual holdings of the Space Science Data Center (NSSDC), all data sets for which direct contact information is available, and some data collections held and serviced by foreign investigators, NASA and other U.S. government agencies. This volume contains narrative descriptions of data sets from low and medium altitude scientific spacecraft and investigations. The following spacecraft series are included: Mariner, Pioneer, Pioneer Venus, Venera, Viking, Voyager, and Helios. Separate indexes to the planetary and interplanetary missions are also provided.

  3. Data catalog series for space science and applications flight flight missions. Volume 2B: Descriptions of data sets from geostationary and high-altitude scientific spacecraft and investigations

    Science.gov (United States)

    Schofield, Norman J. (Editor); Parthasarathy, R. (Editor); Hills, H. Kent (Editor)

    1988-01-01

    The main purpose of the data catalog series is to provide descriptive references to data generated by space science flight missions. The data sets described include all of the actual holdings of the Space Science Data Center (NSSDC), all data sets for which direct contact information is available, and some data collections held and serviced by foreign investigators, NASA and other U.S. government agencies. This volume contains narrative descriptions of data sets from geostationary and high altitude scientific spacecraft and investigations. The following spacecraft series are included: Mariner, Pioneer, Pioneer Venus, Venera, Viking, Voyager, and Helios. Separate indexes to the planetary and interplanetary missions are also provided.

  4. Data catalog series for space science and applications flight missions. Volume 1A: Descriptions of planetary and heliocentric spacecraft and investigations, second edition

    Science.gov (United States)

    Cameron, Winifred Sawtell (Editor); Vostreys, Robert W. (Editor)

    1988-01-01

    The main purpose of the data catalog series is to provide descriptive references to data generated by space science flight missions. The data sets described include all of the actual holdings of the Space Science Data Center (NSSDC), all data sets for which direct contact information is available, and some data collections held and serviced by foreign investigators, NASA and other U.S. government agencies. This volume contains narrative descriptions of planetary and heliocentric spacecraft and associated experiments. The following spacecraft series are included: Mariner, Pioneer, Pioneer Venus, Venera, Viking, Voyager, and Helios. Separate indexes to the planetary and interplanetary missions are also included.

  5. Data catalog series for space science and applications flight missions. Volume 1B: Descriptions of data sets from planetary and heliocentric spacecraft and investigations

    Science.gov (United States)

    Horowitz, Richard (Compiler); Jackson, John E. (Compiler); Cameron, Winifred S. (Compiler)

    1987-01-01

    The main purpose of the data catalog series is to provide descriptive references to data generated by space science flight missions. The data sets described include all of the actual holdings of the Space Science Data Center (NSSDC), all data sets for which direct contact information is available, and some data collections held and serviced by foreign investigators, NASA and other U.S. government agencies. This volume contains narrative descriptions of planetary and heliocentric spacecraft and associated experiments. The following spacecraft series are included: Mariner, Pioneer, Pioneer Venus, Venera, Viking, Voyager, and Helios. Separate indexes to the planetary and interplanetary missions are also provided.

  6. Research and Application on Hierarchical Parallel Volume Rendering Algorithm%多层次并行体绘制算法的研究与应用

    Institute of Scientific and Technical Information of China (English)

    洪振刚; 罗省贤

    2009-01-01

    The 3D data field volume rendering technique is one of the most important research domains in scientific visualization. On the basis of researching and concluding the development procedure of volume rendering and its key technology, combined with multi-core cluster, a parallel ray casting volume rendering algorithm based on hierarchical parallel programming model has been proposed in this paper. This hierarchical parallel algorithm has been used in 3D city shallow geological model successfully. According to the comparative experiments and the analysis of different computation scale on ray casting algorithm between the pure MPI programming model and the hierarchical parallel MPI + OpenMP programming model, the results show that the hierarchical parallel ray casting algorithm accelerates the volume rendering speed, the results also show the hierarchical parallel MPI + OpenMP programming model has better performance than pure MPI programming model.%三维数据场的体绘制技术是科学可视化中一个重要的研究方向,本文在研究和总结体绘制的发展历程与关键技术的基础之上,着重研究了体绘制中的光线投射算法,结合多核处理器机群系统,提出并实现了一种基于多层次并行编程模型的并行光线投射体绘制算法,并成功地将该算法应用于三维城市浅层地质模型,取得了良好的可视化效果.分别对MPI环境和多层次并行编程MPI+OpenMP环境下的光线投射算法进行了不同计算规模的性能比较实验.实验和分析表明,多层次并行光线投射体绘制算法加快了体绘制的速度,MPI+OpenMP多层次并行模型性能高于纯MPI编程模型的性能.

  7. Note: Measurement method for sound velocity of melts in large volume press and its application to liquid sodium up to 2.0 GPa.

    Science.gov (United States)

    Song, Wei; Liu, Yonggang; Wang, Zhigang; Gong, Chaoying; Guo, Jie; Zhou, Wenge; Xie, Hongsen

    2011-08-01

    Based on large volume press and conventional pulse-echo ultrasonic technique, we have overcome the difficulty in determining the length of liquid specimen under high pressure, and the sound velocity in liquid Na has been measured up to 2 GPa. The P-V data deduced by our sound velocity results through equation of state is in an excellent agreement with previous data directly determined by piezometer method. This new experimental technique is convenient and ready for use, being expected to advance investigation on thermodynamic properties of liquid metals and other melts under high pressure. PMID:21895286

  8. Laser program annual report, 1977. Volume 2

    Energy Technology Data Exchange (ETDEWEB)

    Bender, C.F.; Jarman, B.D. (eds.)

    1978-07-01

    This volume contains detailed information on each of the following sections: (1) fusion target design, (2) target fabrication, (3) laser fusion experiments and analysis, (4) advanced lasers, (5) systems and applications studies, and (6) laser isotope separation program. (MOW)

  9. Laser program annual report, 1977. Volume 2

    International Nuclear Information System (INIS)

    This volume contains detailed information on each of the following sections: (1) fusion target design, (2) target fabrication, (3) laser fusion experiments and analysis, (4) advanced lasers, (5) systems and applications studies, and (6) laser isotope separation program

  10. Resource Conservation and Recovery Act, Part B Permit Application [for the Waste Isolation Pilot Plant (WIPP)]. Chapter D, Appendix D1 (conclusion): Volume 3, Revision 1.0

    Energy Technology Data Exchange (ETDEWEB)

    1992-06-01

    This report, Part B (Vol. 3) of the permit application for the WIPP facility, contains information related to the site characterization of the facility, including geology, design, rock salt evaluations, maps, drawings, and shaft excavations. (CBS)

  11. Resource Conservation and Recovery Act Part B permit application [for the Waste Isolation Pilot Plant (WIPP)]. Volume 7: Revision 1.0

    Energy Technology Data Exchange (ETDEWEB)

    1992-07-01

    This permit application (Vol. 7) for the WIPP facility contains appendices related to the following information: Ground water protection; personnel; solid waste management; and memorandums concerning environmental protection standards.

  12. AAAIC '88 - Aerospace Applications of Artificial Intelligence; Proceedings of the Fourth Annual Conference, Dayton, OH, Oct. 25-27, 1988. Volumes 1 ampersand 2

    International Nuclear Information System (INIS)

    Topics presented include integrating neural networks and expert systems, neural networks and signal processing, machine learning, cognition and avionics applications, artificial intelligence and man-machine interface issues, real time expert systems, artificial intelligence, and engineering applications. Also considered are advanced problem solving techniques, combinational optimization for scheduling and resource control, data fusion/sensor fusion, back propagation with momentum, shared weights and recurrency, automatic target recognition, cybernetics, optical neural networks

  13. Ovarian volume throughout life

    DEFF Research Database (Denmark)

    Kelsey, Thomas W; Dodwell, Sarah K; Wilkinson, A Graham;

    2013-01-01

    cancer. To date there is no normative model of ovarian volume throughout life. By searching the published literature for ovarian volume in healthy females, and using our own data from multiple sources (combined n=59,994) we have generated and robustly validated the first model of ovarian volume from...... to about 2.8 mL (95% CI 2.7-2.9 mL) at the menopause and smaller volumes thereafter. Our model allows us to generate normal values and ranges for ovarian volume throughout life. This is the first validated normative model of ovarian volume from conception to old age; it will be of use in the diagnosis...

  14. Isolating cells from female/male blood mixtures using florescence in situ hybridization combined with low volume PCR and its application in forensic science.

    Science.gov (United States)

    Feng, Lei; Li, Cai-Xia; Han, Jun-Ping; Xu, Cheng; Hu, Lan

    2015-11-01

    To obtain single-source short tandem repeat (STR) profiles in trace female/male blood mixture samples, we combined florescence in situ hybridization (FISH), laser microdissection, and low volume PCR (LV-PCR) to isolate male/female cells and improve sensitivity. The results showed that isolation of as few as 10 leukocytes was sufficient to yield full STR profiles in fresh female or male blood samples for 32 independent tests with a low additional alleles rate (3.91%) and drop-out alleles rate (5.01%). Moreover, this procedure was tested in two fresh blood mixture series at three ratios (1:5, 1:10, and 1:20), two mock female/male blood mixture casework samples, and one practical casework sample. Male and female STR profiles were successfully detected in all of these samples, showing that this procedure could be used in forensic casework in the future.

  15. Twenty-First Water Reactor Safety Information Meeting. Volume 3, Primary system integrity; Aging research, products and applications; Structural and seismic engineering; Seismology and geology: Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Monteleone, S. [comp.] [Brookhaven National Lab., Upton, NY (United States)

    1994-04-01

    This three-volume report contains 90 papers out of the 102 that were presented at the Twenty-First Water Reactor Safety Information Meeting held at the Bethesda Marriott Hotel, Bethesda, Maryland, during the week of October 25-27, 1993. The papers are printed in the order of their presentation in each session and describe progress and results of programs in nuclear safety research conducted in this country and abroad. Foreign participation in the meeting included papers presented by researchers from France, Germany, Japan, Russia, Switzerland, Taiwan, and United Kingdom. The titles of the papers and the names of the authors have been updated and may differ from those that appeared in the final program of the meeting. Selected papers were indexed separately for inclusion in the Energy Science and Technology Database.

  16. 投影矩阵在单形体积公式中的应用%Applications of Projection Matrix to a Simplex Volume Formula

    Institute of Scientific and Technical Information of China (English)

    殷红彩; 张华民

    2012-01-01

    利用投影矩阵和正交投影矩阵讨论了单形的多维角,建立了多维角正余弦的表达式,由此得到了单形的一类体积公式,并给出了投影矩阵的性质和第二高维余弦定理的一种新证法.%By using the projection matrix and the orthogonal projection matrix, the multi--dimension an- gle of a simplex is discussed and the expression of sine and cosine is acquired. At the same time we get a kind of volume formula for a simplex and a new way to prove the second high dimension cosine law.

  17. Mission analysis of photovoltaic solar energy conversion. Volume II. Survey of near-term (1976--1985) civilian applications in the United States

    Energy Technology Data Exchange (ETDEWEB)

    Rattin, E. J.

    1977-03-01

    The purpose of this market study was to identify and evaluate potential terrestrial civilian photovoltaic applications in the U.S. which were most likely to contribute significantly to the growth of near-term (to 1985) markets. A survey was conducted which led to the identification of many potential applications for photovoltaic power. These applications were subjected to a screening process which selected about 50 application groupings with considerable promise as near-term markets for photovoltaic arrays. For 21 of these 50 promising application groups, it was possible to make quantitative market estimates that totaled 13 MW/sub pk/ in projected annual array sales in 1985. The markets associated with the remaining 29 groups could not be quantitatively evaluated because of lack of an adequate existing data base and because the primary research required in order to provide such a data base was not feasible within the resources available in the study. If the average size of the markets associated with the unquantified groups, however, is comparable to the average for the quantified cases, then the total non-military U.S. market for arrays may well exceed 25 MW/sub pk//year in 1985. Foreign and U.S. military markets should add significantly to this total. In fact, the consensus of the photovoltaic industry representatives who were contacted is that the total foreign market over the near term may be several times as large as the domestic one.

  18. Necessary conditions for the homogeneous formation of a volume avalanche discharge with specific applications to rare gas-halide excimer laser discharges

    International Nuclear Information System (INIS)

    Self-sustained/avalanche discharges are an efficient method of rare gas-halide excimer laser excitation in small systems. However, with the exceptions of the work reported here, experiments attempting to increase the laser energy output by scaling up the discharge volume and/or pulse duration have not been successful. The major problem encountered in scaling experiments has been the formation of arc channels in the discharge volume. The presence of arcing can totally disrupt proper laser operation. This problem stems from a general lack of understanding of high pressure avalanche discharge phenomena. Therefore, clarifying the basic discharge formation process and establishing a set of criteria under which a homogeneous avalanche discharge can be obtained is of central importance in defining the scaling limits of avalanche discharge lasers. The work presented here reviews the phenomena involved in high E/n (electric field to gas number density ratio) breakdown and its relationship to the formation of spatially homogeneous discharges. This relationship was first explored by A.J. Palmer in 1974. The basic requirement of his model was that the preionization density be large enough to cause an appreciable overlap of the primary electron avalanches and hence smooth out the ensuing space-charge fields to the extent that individual streamer formation would be prevented. This is the same basic model used in the more detailed discharge formation analysis developed here except that the effects of a time varying electric field caused by a finite voltage rise time and the effects due to the various electrochemical properties of the gas mixture are property taken into consideration

  19. Ultra-trace plutonium determination in small volume seawater by sector field inductively coupled plasma mass spectrometry with application to Fukushima seawater samples.

    Science.gov (United States)

    Bu, Wenting; Zheng, Jian; Guo, Qiuju; Aono, Tatsuo; Tagami, Keiko; Uchida, Shigeo; Tazoe, Hirofumi; Yamada, Masatoshi

    2014-04-11

    Long-term monitoring of Pu isotopes in seawater is required for assessing Pu contamination in the marine environment from the Fukushima Dai-ichi Nuclear Power Plant accident. In this study, we established an accurate and precise analytical method based on anion-exchange chromatography and SF-ICP-MS. This method was able to determine Pu isotopes in seawater samples with small volumes (20-60L). The U decontamination factor was 3×10(7)-1×10(8), which provided sufficient removal of interfering U from the seawater samples. The estimated limits of detection for (239)Pu and (240)Pu were 0.11fgmL(-1) and 0.08fgmL(-1), respectively, which corresponded to 0.01mBqm(-3) for (239)Pu and 0.03mBqm(-3) for (240)Pu when a 20L volume of seawater was measured. We achieved good precision (2.9%) and accuracy (0.8%) for measurement of the (240)Pu/(239)Pu atom ratio in the standard Pu solution with a (239)Pu concentration of 11fgmL(-1) and (240)Pu concentration of 2.7fgmL(-1). Seawater reference materials were used for the method validation and both the (239+240)Pu activities and (240)Pu/(239)Pu atom ratios agreed well with the expected values. Surface and bottom seawater samples collected off Fukushima in the western North Pacific since March 2011 were analyzed. Our results suggested that there was no significant variation of the Pu distribution in seawater in the investigated areas compared to the distribution before the accident.

  20. The derivation of two-fluid, three-field governing equations in porous media using time-volume averaging formulation and its application to develop a safety analysis code

    International Nuclear Information System (INIS)

    Time-volume averaged two-fluid model considering structural materials in a control volume is formulated for two-phase flow analyses. It is obtained rigorously by averaging local time-averaged two-fluid model over a control volume including structural materials. It is applied to the derivation of balance equations for two-fluid three-field two-component flow model considering the interfacial mass, momentum and energy jump conditions. The internal energy balance equation instead of the total energy balance equation is more appropriate for the nuclear power plant thermal hydraulics. This kind of model is necessary to simulate the direct vessel injection system in Korean PWRs that delivers emergency core cooling water directly to the downcomer. Derived balance equations for gas, liquid and droplet field are used to develop a general purpose system code, i.e., SPACE (Safety and Performance Analysis Code). SPACE adopts the semi-implicit scheme. The finite volume approach is used to discretize the balance equations. SPACE can handle multi-dimensional problems. Unstructured collocated or structured staggered solver can be chosen by users. If necessary, combination of them can also be possible. As the network approach is required for system code, SPACE can handle network mesh blocks in parallel with structured and/or unstructured mesh blocks. Concerning the complexity of calculating the porosity, the calculation procedure is devised using the CAD tools in parallel with mesh generator for its estimation. By overlapping a cell generated by mesh handler onto the solid model generated by CAD, and by estimating the interaction among them, the porosity can be estimated. Several test cases are presented herein to show the adequacy of the SPACE approach. U-tube gas-water problem can show that the predicted frequency is matched with theory. Nine-volume water over steam problem can be used to see the gravitational head effect and the development of countercurrent flow from an initial

  1. Seismic engineering: 1993--Volume 1

    International Nuclear Information System (INIS)

    Separate abstracts were prepared for the technical papers presented at the American Society of Mechanical Engineers 1993 Pressure Vessels and Piping Conference on July 25--29 in Denver, Colorado. Knowledge gained from seismic effect and method development for seismic analysis have seen continuing advancement in the past year. This volume contains fifteen papers dealing with seismic methods, analysis, and applications, nine papers dealing with piping seismic design and evaluation, and eight papers dealing with piping supports and components

  2. Volcanic sulfur dioxide index and volcanic explosivity index inferred from eruptive volume of volcanoes in Jeju Island, Korea: application to volcanic hazard mitigation

    Science.gov (United States)

    Ko, Bokyun; Yun, Sung-Hyo

    2016-04-01

    Jeju Island located in the southwestern part of Korea Peninsula is a volcanic island composed of lavaflows, pyroclasts, and around 450 monogenetic volcanoes. The volcanic activity of the island commenced with phreatomagmatic eruptions under subaqueous condition ca. 1.8-2.0 Ma and lasted until ca. 1,000 year BP. For evaluating volcanic activity of the most recently erupted volcanoes with reported age, volcanic explosivity index (VEI) and volcanic sulfur dioxide index (VSI) of three volcanoes (Ilchulbong tuff cone, Songaksan tuff ring, and Biyangdo scoria cone) are inferred from their eruptive volumes. The quantity of eruptive materials such as tuff, lavaflow, scoria, and so on, is calculated using a model developed in Auckland Volcanic Field which has similar volcanic setting to the island. The eruptive volumes of them are 11,911,534 m3, 24,987,557 m3, and 9,652,025 m3, which correspond to VEI of 3, 3, and 2, respectively. According to the correlation between VEI and VSI, the average quantity of SO2 emission during an eruption with VEI of 3 is 2-8 × 103 kiloton considering that the island was formed under intraplate tectonic setting. Jeju Island was regarded as an extinct volcano, however, several studies have recently reported some volcanic eruption ages within 10,000 year BP owing to the development in age dating technique. Thus, the island is a dormant volcano potentially implying high probability to erupt again in the future. The volcanoes might have explosive eruptions (vulcanian to plinian) with the possibility that SO2 emitted by the eruption reaches stratosphere causing climate change due to backscattering incoming solar radiation, increase in cloud reflectivity, etc. Consequently, recommencement of volcanic eruption in the island is able to result in serious volcanic hazard and this study provides fundamental and important data for volcanic hazard mitigation of East Asia as well as the island. ACKNOWLEDGMENTS: This research was supported by a grant [MPSS

  3. MSCT容积再现在并腿畸形尸检中的应用%Application of MSCT with volume rendering in sirenomelia autopsy

    Institute of Scientific and Technical Information of China (English)

    马慧静; 徐来; 邵剑波; 杨小红

    2014-01-01

    目的:探讨胎儿并腿畸形的骨骼异常及尸检胎儿 MSCT容积再现对产前B超的提示作用。方法:对8例疑似并腿畸形胎儿行 MRI检查,引产后行 MSCT检查。结果:8例并腿畸形胎儿中,7例为单胎,1例为臀部联体双胎之一。8例中,1例表现为单个下肢,7例为形式各异的下肢融合畸形。8例均有髂骨异常、尾椎部分或全部缺失。7例伴有各种各样的胸腰椎和肋骨畸形,2例并左上肢畸形融合。结论:MSCT容积再现可以提供胎儿详细立体的影像学资料,提高对并腿畸形骨骼异常的认识及产前诊断水平。%Objective:To discuss the skeletal anomalies of sirenomelia of fetus and the value of post-natal MSCT with volume rendering technique for fetal prenatal ultrasound.Methods:8 fetuses suspected of sirenomelia underwent MRI exami-nation and these fetuses after induced labor underwent MSCT examination.Results:Of the 8 cases of sirenomelia,7 cases were monocyesis,and one case was one of coxal conjoined twins,one of the twins had sirenomelia.Of the 8 cases,one case had single lower limb,7 cases had various fusion of the lower limbs.There were iliac bone anomalies and complete or partial caudal vertebra defects in 7 cases.There were various deformities of thoracic and lumbar vertebrae and ribs deformities in 7 cases and fusion of the upper limbs in 2 cases.Conclusion:MSCT with volume rendering can provide significant and clear im-aging information of the entire fetus,which can improve the understanding and prenatal diagnostic level of skeletal anomalies of sirenomelia.

  4. The application of large volume airgun sources to the onshore-offshore seismic surveys: implication of the experimental results in northern South China Sea

    Institute of Scientific and Technical Information of China (English)

    QIU XueLin; CHEN Yong; ZHU RiXiang; XU HuiLong; SHI XiaoBin; YE ChunMing; ZHAO MingHui; XIA ShaoHong

    2007-01-01

    Onshore-offshore seismic experiments were carried out for the first time in northern South China Sea using large volume airgun sources at sea and seismic stations on land. The experimental results indicate that seismic signals from the new airgun array of R/V Shiyan 2 can be detected as far as 255 km. The signal effective area reaches nearly 50000 km2, which covers Hong Kong and Pearl River Delta. Compared with the old airgun array, the signal amplitude, propagation distance and effective area of the new airgun array have been increased notably, which demonstrates that the upgrade of the airgun source was successful. Comparisons with previous experimental results in other regions show that the shooting effect of the new airgun array is similar to those best airgun sources in the world. Especially, it is a new breakthrough in using the permanent seismic stations onshore to record long distance airgun signals offshore, which has great significance to the realization of the "seismic radar" concept and the 3D seismic surveys of crustal structure in coastal areas.

  5. Monge and the three point space resection problem: an application to the reconstruction of heights and volumes from a photograph of 1892

    Directory of Open Access Journals (Sweden)

    Federico Fallavollita

    2013-10-01

    Full Text Available The purpose of photogrammetric restitution is the reconstruction of the volumes, now lost, located along the road that crosses the village, on the left side of the photo. The reconstruction of points in space from twodimensional images is possible if these photos are projective figure and we have at least two projective oriented stars. The first image is a vintage photograph, the second is a figure reconstructed from an aerial photo of AM in 1938 and from the survey of the masonry still present at the site. For the survey, one of the two projective stars is assimilated to a class of vertical straight lines. With regard to photography, the problem is decomposed into two typical phases of photogrammetric processes: the internal orientation and the absolute orientation. For the absolute orientation we used the method of the pyramid vertex which, in use since the Eighteenth Century, consists in determining the projection center from three given points of which are known the positions in space.

  6. Adaptive finite volume methods with well-balanced Riemann solvers for modeling floods in rugged terrain: Application to the Malpasset dam-break flood (France, 1959)

    Science.gov (United States)

    George, D.L.

    2011-01-01

    The simulation of advancing flood waves over rugged topography, by solving the shallow-water equations with well-balanced high-resolution finite volume methods and block-structured dynamic adaptive mesh refinement (AMR), is described and validated in this paper. The efficiency of block-structured AMR makes large-scale problems tractable, and allows the use of accurate and stable methods developed for solving general hyperbolic problems on quadrilateral grids. Features indicative of flooding in rugged terrain, such as advancing wet-dry fronts and non-stationary steady states due to balanced source terms from variable topography, present unique challenges and require modifications such as special Riemann solvers. A well-balanced Riemann solver for inundation and general (non-stationary) flow over topography is tested in this context. The difficulties of modeling floods in rugged terrain, and the rationale for and efficacy of using AMR and well-balanced methods, are presented. The algorithms are validated by simulating the Malpasset dam-break flood (France, 1959), which has served as a benchmark problem previously. Historical field data, laboratory model data and other numerical simulation results (computed on static fitted meshes) are shown for comparison. The methods are implemented in GEOCLAW, a subset of the open-source CLAWPACK software. All the software is freely available at. Published in 2010 by John Wiley & Sons, Ltd.

  7. Water pollution screening by large-volume injection of aqueous samples and application to GC/MS analysis of a river Elbe sample

    Energy Technology Data Exchange (ETDEWEB)

    Mueller, S.; Efer, J.; Engewald, W. [Leipzig Univ. (Germany). Inst. fuer Analytische Chemie

    1997-03-01

    The large-volume sampling of aqueous samples in a programmed temperature vaporizer (PTV) injector was used successfully for the target and non-target analysis of real samples. In this still rarely applied method, e.g., 1 mL of the water sample to be analyzed is slowly injected direct into the PTV. The vaporized water is eliminated through the split vent. The analytes are concentrated onto an adsorbent inside the insert and subsequently thermally desorbed. The capability of the method is demonstrated using a sample from the river Elbe. By means of coupling this method with a mass selective detector in SIM mode (target analysis) the method allows the determination of pollutants in the concentration range up to 0.01 {mu}g/L. Furthermore, PTV enrichment is an effective and time-saving method for non-target analysis in SCAN mode. In a sample from the river Elbe over 20 compounds were identified. (orig.) With 3 figs., 2 tabs.

  8. 大体积承台混凝土配合比设计及工程应用%Design and Construction Application of Large Volume Cap Concrete

    Institute of Scientific and Technical Information of China (English)

    孙宏图

    2016-01-01

    针对东明黄河公路大桥主桥主墩承台混凝土的特点,通过掺加大掺量复合矿物掺合料、细集料采用机制砂及掺加聚羧酸缓凝高效减水剂的方案,配制出密实性好、水化热低、抗裂性能好的大体积混凝土。同时,结合科学的施工措施,有效防止了大体积承台温度裂缝的产生。%Aimed at the characteristics of the main pier pile concrete of the main bridge of Dongming Yellow River Highway Bridge, the mass concrete with good compactness, low hydration heat, good crack resistance is made by the plan of mixing lots of composite mineral admixture, using machine-made sand as fine aggregate and adding polycarboxylic acid retarded high efficiency water reducing agent. At the same time, the large volume cap temperature cracks are effectively prevented by the scientific construction measures.

  9. Low concentration ratio solar array for low Earth orbit multi-100 kW application. Volume 1: Design, analysis and development tests

    Science.gov (United States)

    1983-01-01

    A preliminary design effort directed toward a low concentration ratio photovoltaic array system capable of delivering multihundred kilowatts (300 kW to 1000 kW range) in low earth orbit is described. The array system consists of two or more array modules each capable of delivering between 113 kW to 175 kW using silicon solar cells or gallium arsenide solar cells, respectively. The array module deployed area is 1320 square meters and consists of 4356 pyramidal concentrator elements. The module, when stowed in the Space Shuttle's payload bay, has a stowage volume of a cube with 3.24 meters on a side. The concentrator elements are sized for a geometric concentration ratio (GCR) of six with an aperture area of .25 sq. m. The structural analysis and design trades leading to the baseline design are discussed. It describes the configuration, as well as optical, thermal and electrical performance analyses that support the design and overall performance estimates for the array are described.

  10. Realtime or Delayed Tele-Echography Using (A) a Robotic Arm, ISDN or Satellite Lines, (B) a Volumic Echographic Capture Mode and Internet (Application to Abdomen and Fetus)

    Science.gov (United States)

    Arbeille, Ph.; Cloppet, F.; Boucher, A.; Capri, A.; Vincent, N.

    2008-06-01

    Objective: to test (a) the tele-echography in realtime based on the use of a robotic arm, (b) the delayed tele echography using a volumic echographic capture and delayed processing. Method: A dedicated robotic arm (ESTELE) holding a real ultrasound probe is remotely controlled from the expert site with a fictive probe, and reproduces on the real probe all the movements of the expert hand. A dedicated motorized probe holder (TILTER) was used for tilting a 2D probe from -45 to +45°. Results: During fetal robotized Tele-echography (n=50) the expert was able to visualize and measure the fetal structures in 95% of the cases, while during abdomen echography (n=87) the expert visualized the main organs and lesions in 87% of the cases. The mean duration of the robotized tele echography session for one patient was 20+/-10 min. The delayed echography using the TILTER was tested on 40 patients. The organs were adequately visualized in 85% of the cases after 3 capture per organ. The average time from the first capture until the diagnostic was delivered was 40+/-10 minutes. Conclusion: Realtime or delayed Tele-echography provide similar information as direct examination in at least 85% of the cases. No false diagnostic was reported.

  11. Volume Regulation in Epithelia

    DEFF Research Database (Denmark)

    Larsen, Erik Hviid; Hoffmann, Else Kay

    2016-01-01

    We review studies on regulatory volume decrease (RVD) and regulatory volume increase (RVI) of major ion and water transporting vertebrate epithelia. The rate of RVD and RVI is faster in cells of high osmotic permeability like amphibian gallbladder and mammalian proximal tubule as compared...... to amphibian skin and mammalian cortical collecting tubule of low and intermediate osmotic permeability. Crosstalk between entrance and exit mechanisms interferes with volume regulation both at aniso-osmotic and iso-osmotic volume perturbations. It has been proposed that cell volume regulation is an intrinsic...

  12. Preliminary application of dynamic pulmonary xenon-133 single-photon emission tomography in the evaluation of patients with pulmonary emphysema for thoracoscopic lung volume reduction surgery

    Energy Technology Data Exchange (ETDEWEB)

    Suga, Kazuyoshi; Nishigauchi, Kazuya; Matsunaga, Naofumi; Matsumoto, Tsuneo; Kume, Norihiko [Univ. School of Medicine, Yamaguchi (Japan). Dept. of Radiol.; Sugi, Kazuro; Esato, Kensuke [First Department of Surgery, Yamaguchi University School of Medicine, Ube, Yamaguchi (Japan)

    1998-04-01

    Dynamic pulmonary xenon-133 single-photon emission tomography (SPET) with three-dimensional (3D) displays was preliminarily applied to select resection targets for thoracoscopic lung volume reduction surgery (LVRS) and to assess regional ventilatory changes following surgery. Dynamic SPET was performed using a triple-detector SPET system in 14 patients with pulmonary emphysema before and after LVRS. After reconstructing colour-illuminated, surface-rendered 3D images of equilibrium (EQ) and 3-min washout (WO{sub 3}), a single 3D fusion display was created from these two different time-course image sets, in which the 3D WO{sub 3} image indicating {sup 133}Xe retention was visible through the overlying 3D EQ image delineating lung contours. Volumetric extent of retention on this display was quantified by a {sup 133}Xe retention index, defined as the ratio (%) of total pixel numbers of segmented 3-min WO data to those of EQ data. {sup 133}Xe SPET and appropriately thresholded 3D displays efficiently localized a total of 36 retention sites; 19 (52.7%) of these sites were not localized by CT because they were within the widely or homogeneously spreading non-bullous emphysematous lung tissues. The 3D displays enhanced the perception of anatomical configurations and the extent of {sup 133}Xe retention compared with multislice tomograms. Postoperatively, 3D fusion display visualized the details of regional changes in retention, and changes in the retention index on the 3D display with a standardized threshold correlated well with changes in {sup 133}Xe clearance time (T{sub 1/2}) and %FEV{sub 1} (r = 0.881 and 0.856, respectively; P<0.0001). This preliminary study indicates that {sup 133}Xe SPET and appropriately thresholded, topographic 3D displays are of potential use in selecting resection targets for LVRS, and in evaluating the treatment effects on regional ventilation. (orig.) With 4 figs., 1 tab., 32 refs.

  13. Preliminary application of dynamic pulmonary xenon-133 single-photon emission tomography in the evaluation of patients with pulmonary emphysema for thoracoscopic lung volume reduction surgery

    International Nuclear Information System (INIS)

    Dynamic pulmonary xenon-133 single-photon emission tomography (SPET) with three-dimensional (3D) displays was preliminarily applied to select resection targets for thoracoscopic lung volume reduction surgery (LVRS) and to assess regional ventilatory changes following surgery. Dynamic SPET was performed using a triple-detector SPET system in 14 patients with pulmonary emphysema before and after LVRS. After reconstructing colour-illuminated, surface-rendered 3D images of equilibrium (EQ) and 3-min washout (WO3), a single 3D fusion display was created from these two different time-course image sets, in which the 3D WO3 image indicating 133Xe retention was visible through the overlying 3D EQ image delineating lung contours. Volumetric extent of retention on this display was quantified by a 133Xe retention index, defined as the ratio (%) of total pixel numbers of segmented 3-min WO data to those of EQ data. 133Xe SPET and appropriately thresholded 3D displays efficiently localized a total of 36 retention sites; 19 (52.7%) of these sites were not localized by CT because they were within the widely or homogeneously spreading non-bullous emphysematous lung tissues. The 3D displays enhanced the perception of anatomical configurations and the extent of 133Xe retention compared with multislice tomograms. Postoperatively, 3D fusion display visualized the details of regional changes in retention, and changes in the retention index on the 3D display with a standardized threshold correlated well with changes in 133Xe clearance time (T1/2) and %FEV1 (r = 0.881 and 0.856, respectively; P133Xe SPET and appropriately thresholded, topographic 3D displays are of potential use in selecting resection targets for LVRS, and in evaluating the treatment effects on regional ventilation. (orig.)

  14. Direct use applications of geothermal resources at Desert Hot Springs, California. Final report, May 23, 1977--July 31, 1978. Volume II: appendixes

    Energy Technology Data Exchange (ETDEWEB)

    Christiansen, C.C.

    1978-07-01

    The following appendixes are included: Desert Hot Springs (DHS) Geothermal Project Advisory Board, Geothermal Citizens Advisory Committee, community needs assessment, geothermal resource characterization, a detailed discussion of the geothermal applications considered for DHS, space/water heating, agricultural operations, detailed analysis of a geothermal aquaculture facility, detailed discussion of proposed energy cascading systems for DHS, regulatory requirements, environmental impact assessment, resource management plan, and geothermal resources property rights and powers of cities to regulate indigenous geothermal resources and to finance construction of facilities for utilization of such resources. (MHR)

  15. Uncooled amorphous silicon TEC-less 1/4 VGA IRFPA with 25μm pixel-pitch for high volume applications

    Science.gov (United States)

    Durand, A.; Minassian, C.; Tissot, J. L.; Vilain, M.; Robert, P.; Touvignon, A.; Chiappa, J. M.; Pistre, C.

    2009-05-01

    The high level of accumulated expertise by ULIS on uncooled microbolometers TEC-less operation enables ULIS to develop 384 x 288 (1/4 VGA) IRFPA format with 25μm pixel-pitch especially designed for TEC-less application. This detector, while keeping all the performances and all the innovations developed on previous ULIS ROIC (NETD performance, detector configuration by serial link, low power consumption and wide electrical dynamic range ...), can be operated on a wide range of ambient temperature, with constant settings. We present in this paper the electro-optical performances and the TEC-less capability of this device. The thermal behavior is described in detail.

  16. Annealing Reduces Free Volumes In Thermoplastics

    Science.gov (United States)

    Singh, Jag J.; St. Clair, Terry L.

    1988-01-01

    Investigation conducted to determine free volumes and water-absorption characteristics of two types of thermoplastic polymide as functions of annealing histories. Reductions reach asymptotic values after several annealing cycles. High-temperature thermoplastics excellent candidates for use in aerospace applications. Graphite-fiber composites containing thermoplastic matrices have wide applicability.

  17. Development of a plume-in-grid model for industrial point and volume sources: application to power plant and refinery sources in the Paris region

    Science.gov (United States)

    Kim, Y.; Seigneur, C.; Duclaux, O.

    2014-04-01

    Plume-in-grid (PinG) models incorporating a host Eulerian model and a subgrid-scale model (usually a Gaussian plume or puff model) have been used for the simulations of stack emissions (e.g., fossil fuel-fired power plants and cement plants) for gaseous and particulate species such as nitrogen oxides (NOx), sulfur dioxide (SO2), particulate matter (PM) and mercury (Hg). Here, we describe the extension of a PinG model to study the impact of an oil refinery where volatile organic compound (VOC) emissions can be important. The model is based on a reactive PinG model for ozone (O3), which incorporates a three-dimensional (3-D) Eulerian model and a Gaussian puff model. The model is extended to treat PM, with treatments of aerosol chemistry, particle size distribution, and the formation of secondary aerosols, which are consistent in both the 3-D Eulerian host model and the Gaussian puff model. Furthermore, the PinG model is extended to include the treatment of volume sources to simulate fugitive VOC emissions. The new PinG model is evaluated over Greater Paris during July 2009. Model performance is satisfactory for O3, PM2.5 and most PM2.5 components. Two industrial sources, a coal-fired power plant and an oil refinery, are simulated with the PinG model. The characteristics of the sources (stack height and diameter, exhaust temperature and velocity) govern the surface concentrations of primary pollutants (NOx, SO2 and VOC). O3 concentrations are impacted differently near the power plant than near the refinery, because of the presence of VOC emissions at the latter. The formation of sulfate is influenced by both the dispersion of SO2 and the oxidant concentration; however, the former tends to dominate in the simulations presented here. The impact of PinG modeling on the formation of secondary organic aerosol (SOA) is small and results mostly from the effect of different oxidant concentrations on biogenic SOA formation. The investigation of the criteria for injecting

  18. Draft Title 40 CFR 191 compliance certification application for the Waste Isolation Pilot Plant. Volume 9: Appendices RM, SCR, SER, SUM, WRAC

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-31

    The Rock Mechanics Program is important to the establishment of a radioactive waste repository in salt because rock mechanics deals with the prediction of creep closure and eventual encapsulation of the waste. The intent of this paper is to give the current status of the program. This program consists of three major modeling efforts: continuum creep, fracture, and the disturbed rock zone. These models, together with laboratory material parameters, plastic flow potentials, initial and boundary input data, and other peripheral information forms the predictive technology. The extent to which the predictive technology is validated against in situ test data adds certainty to the method. Application of the technology is through simulations of the test results, design, or performance using numerical codes. In summary, the predictive capabilities are technically sound and reasonable. The current status of the program is that which would be advanced for compliance.

  19. Integrated Application of Active Controls (IAAC) technology to an advanced subsonic transport project. ACT/Control/Guidance System study, volume 1

    Science.gov (United States)

    1982-01-01

    The active control technology (ACT) control/guidance system task of the integrated application of active controls (IAAC) technology project within the NASA energy efficient transport program was documented. The air traffic environment of navigation and air traffic control systems and procedures were extrapolated. An approach to listing flight functions which will be performed by systems and crew of an ACT configured airplane of the 1990s, and a determination of function criticalities to safety of flight, are the basis of candidate integrated ACT/Control/Guidance System architecture. The system mechanizes five active control functions: pitch augmented stability, angle of attack limiting, lateral/directional augmented stability, gust load alleviation, and maneuver load control. The scope and requirements of a program for simulating the integrated ACT avionics and flight deck system, with pilot in the loop, are defined, system and crew interface elements are simulated, and mechanization is recommended. Relationships between system design and crew roles and procedures are evaluated.

  20. Draft Title 40 CFR 191 compliance certification application for the Waste Isolation Pilot Plant. Volume 9: Appendices RM, SCR, SER, SUM, WRAC

    International Nuclear Information System (INIS)

    The Rock Mechanics Program is important to the establishment of a radioactive waste repository in salt because rock mechanics deals with the prediction of creep closure and eventual encapsulation of the waste. The intent of this paper is to give the current status of the program. This program consists of three major modeling efforts: continuum creep, fracture, and the disturbed rock zone. These models, together with laboratory material parameters, plastic flow potentials, initial and boundary input data, and other peripheral information forms the predictive technology. The extent to which the predictive technology is validated against in situ test data adds certainty to the method. Application of the technology is through simulations of the test results, design, or performance using numerical codes. In summary, the predictive capabilities are technically sound and reasonable. The current status of the program is that which would be advanced for compliance

  1. Development, manufacturing and testing of micromechanical pressure and volume-flow transducers for pneumatic applications; Entwicklung, Herstellung und Erprobung mikromechanischer Druck- und Durchflusssensoren fuer pneumatische Anwendungen

    Energy Technology Data Exchange (ETDEWEB)

    Martin, J.

    1998-12-01

    The present dissertation deals with novel micromechanical pressure and volume-flow transducers. They consist of a circular plastic transducer element which is elastically beared on a carrier membrane in the transducer case. A strain gauge rosette is embedded into the transducer element. This rosette consists of four active strain gauges that form a Wheatstone measuring bridge. The strain gauges are produced by wet-chemical etching from a 0.1 {mu}m thin gold layer. The nominal structural width of the measurement wires amounts to 12 {mu}m. The measuring bridge is operated at a constant supply voltage of 1 V. The pressure-induced deformations of the transducer element are detected by the strain gauges and transformed into a measurement voltage which is directly proportional to the acting differential pressure. The transducer element and the carrier membrane are made of polyimide. Both parts of the transducer case, between which the carrier membrane is located, are made of polysulfone by injection molding. The pressure transducers are manufactured and tested for the differential pressure ranges of 20, 250, 500, 750 and 1000 hPa. The diameter of the transducer element is about 1300 {mu}m for a pressure transducer with a measuring range of 20 hPa. With an increasing measuring range, the diameter decreases continuously such that a transducer with a measuring range of 1000 hPa has a transducer element diameter of 580 {mu}m. The flow transducer is obtained by the installation of a fine-pressure transducer (measuring range 20 hPa) into a case with integrated measuring capillaries. Three variants have been developed for the measuring ranges of 0.1, 1 and 10 sccm. The measuring capillary is dimensioned such that a laminar flow is generated inside. Hence, the pressure loss measured is directly proportional to the flow according to Hagen-Poiseuille`s law. The three different measuring ranges are obtained by using measuring capillaries of variable cross-section. (orig

  2. Formation of superpower volume discharges and their applications%超高功率体放电的形成及其应用

    Institute of Scientific and Technical Information of China (English)

    TARASENKO V F; BAKSHT E KH; BURACHENKO A G; LOMAEV M I; RYBKA D V; SHULEPOV M A; SOROKIN D A; SHUTKO V

    2011-01-01

    研究了氮气中的高压体(扩散)放电特性,实验中施加的极间隙脉冲电压达数百千伏,持续时间为数纳秒,上升时间为几个纳秒,给出了实验结果.研究了氦气压强为((0.4-2)×105Pa时,从扩散形式到火花放电的放电转换过程.确定了在氮气压强下电流幅度与逃逸电子束电流脉宽的关系.结果表明,导致隙间扩散放电的超短雪崩电子束(SAEB)对放电过程有重要的影响.在该压强下得出了SAEB瞬间产生相对放电电流的时延与压强的关系,根据该关系,时延随着压强增加而变化,并且在压强为2 ×105 Pa时最小,同时扩散放电电流脉冲的峰值随压强增加而减小.在0.5 × 105 Pa的压强下,使用刀片电极和6 cm长的N2:SF6=10:1的激活媒质,得到了输出能量为2 mJ、脉冲功率为0.55 MW的激光.最后,在大气压强下,对AlBe箔片进行了重复频率放电处理(REP),其表层清除了碳而且氧原子以450nm/300pulse渗人箔片.%The experimental results on study of characteristics of the high-pressure volume (diffuse) discharges in nitrogen at applying to the interelectrode gap voltage pulse with the amplitude of hundreds kV, duration of several ns and the rise-time of fraction ns are presented. At the pressure range of nitrogen in (0. 2-4) × 105 Pa, the discharge transformation from the diffuse form to the spark is investigated. Dependencies of the current amplitude and FWHM of the runaway electron beam current on nitrogen pressure are determined. It is shown that the generation of the Supershort Avalanche Electron Beam (SAEB) leading to the formation of diffuse discharge in the gap has a significant influence on the development of the discharge. At the pressures indicated above, the dependence of the time delay of SAEB's moment generating relatively discharge current beginning on pressure are obtained. According to this dependence, the time delay changes as pressure increases and it is minimal at pressure of 2× 105

  3. Waste minimization handbook, Volume 1

    International Nuclear Information System (INIS)

    This technical guide presents various methods used by industry to minimize low-level radioactive waste (LLW) generated during decommissioning and decontamination (D and D) activities. Such activities generate significant amounts of LLW during their operations. Waste minimization refers to any measure, procedure, or technique that reduces the amount of waste generated during a specific operation or project. Preventive waste minimization techniques implemented when a project is initiated can significantly reduce waste. Techniques implemented during decontamination activities reduce the cost of decommissioning. The application of waste minimization techniques is not limited to D and D activities; it is also useful during any phase of a facility's life cycle. This compendium will be supplemented with a second volume of abstracts of hundreds of papers related to minimizing low-level nuclear waste. This second volume is expected to be released in late 1996

  4. Waste minimization handbook, Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Boing, L.E.; Coffey, M.J.

    1995-12-01

    This technical guide presents various methods used by industry to minimize low-level radioactive waste (LLW) generated during decommissioning and decontamination (D and D) activities. Such activities generate significant amounts of LLW during their operations. Waste minimization refers to any measure, procedure, or technique that reduces the amount of waste generated during a specific operation or project. Preventive waste minimization techniques implemented when a project is initiated can significantly reduce waste. Techniques implemented during decontamination activities reduce the cost of decommissioning. The application of waste minimization techniques is not limited to D and D activities; it is also useful during any phase of a facility`s life cycle. This compendium will be supplemented with a second volume of abstracts of hundreds of papers related to minimizing low-level nuclear waste. This second volume is expected to be released in late 1996.

  5. Development and application of a risk assessment method for radioactive waste management. Volume I. Generic description of AMRAW-A model

    International Nuclear Information System (INIS)

    A Radioactive Waste Management Systems Model, is presented. The systems model and associated computer code called AMRAW (Assessment Method for Radioactive Waste), has two parts. The first part, AMRAW-A, consists of the Source Term (radioactive inventory versus time), the Release Model, and the Environmental Model. The Release Model considers various geologic and man-caused events which are potential mechanisms for release of radioactive material beyond the immediate environs of a repository or other location; the risk analysis mode uses events distributed probabilistically over time, and the consequence analysis mode uses discrete events occurring at specified times. The Environmental Model includes: (1) the transport to and accumulations at various receptors in the biosphere, (2) pathways from these environmental concentrations, and (3) resulting radiation dose to man. The second part of the systems model, AMRAW-B, is the Economic Model which calculates health effects corresponding to the various organ dose rates from AMRAW-A, collects these health effects in terms of economic costs and attributes these costs to radionuclides, decay groups, and elements initially in the waste inventory. Implementation, with calculated results, of AMRAW for Terminal Storage in a Bedded Salt Reference Repository are presented. Preliminary demonstrations for the repository operations phase of waste management and terminal storage in a shale formation are described; possible applications to other radioactive and nonradioactive hazardous materials are discussed. AMRAW uniquely links all steps together in a continuous calculation sequence

  6. New criterion for algebraic volume density property

    CERN Document Server

    Kaliman, Shulim

    2012-01-01

    A smooth affine algebraic variety $X$ equipped with an algebraic volume form $\\omega$ has the algebraic volume density property (AVDP) if the Lie algebra generated by completely integrable algebraic vector fields of $\\omega$-divergence zero coincides with the space of all algebraic vector fields of $\\omega$-divergence zero. We develop an effective criterion of verifying whether a given $X$ has AVDP. As an application of this method we establish AVDP for any homogeneous space $X=G/R$ that admits a $G$-invariant algebraic volume form where $G$ is a linear algebraic group and $R$ is a closed reductive subgroup of $G$.

  7. Finite volume hydromechanical simulation in porous media

    Science.gov (United States)

    Nordbotten, Jan Martin

    2014-05-01

    Cell-centered finite volume methods are prevailing in numerical simulation of flow in porous media. However, due to the lack of cell-centered finite volume methods for mechanics, coupled flow and deformation is usually treated either by coupled finite-volume-finite element discretizations, or within a finite element setting. The former approach is unfavorable as it introduces two separate grid structures, while the latter approach loses the advantages of finite volume methods for the flow equation. Recently, we proposed a cell-centered finite volume method for elasticity. Herein, we explore the applicability of this novel method to provide a compatible finite volume discretization for coupled hydromechanic flows in porous media. We detail in particular the issue of coupling terms, and show how this is naturally handled. Furthermore, we observe how the cell-centered finite volume framework naturally allows for modeling fractured and fracturing porous media through internal boundary conditions. We support the discussion with a set of numerical examples: the convergence properties of the coupled scheme are first investigated; second, we illustrate the practical applicability of the method both for fractured and heterogeneous media.

  8. Volume difference inequalities

    OpenAIRE

    Giannopoulos, Apostolos; Koldobsky, Alexander

    2016-01-01

    We prove several inequalities estimating the distance between volumes of two bodies in terms of the maximal or minimal difference between areas of sections or projections of these bodies. We also provide extensions in which volume is replaced by an arbitrary measure.

  9. Bronchoscopic lung volume reduction

    Directory of Open Access Journals (Sweden)

    M. I. Polkey

    2006-12-01

    Full Text Available Surgical lung volume reduction can improve exercise performance and forced expiratory volume in one second in patients with emphysema. However, the procedure is associated with a 5% mortality rate and a nonresponse rate of 25%. Accordingly, interest has focused on alternative ways of reducing lung volume. Two principle approaches are used: collapse of the diseased area using blockers placed endobronchially and the creation of extrapulmonary pathways. Preliminary data from the former approach suggest that it can be successful and that the magnitude of success is related to reduction in dynamic hyperinflation.

  10. Towards the Amplituhedron Volume

    CERN Document Server

    Ferro, Livia; Orta, Andrea; Parisi, Matteo

    2015-01-01

    It has been recently conjectured that scattering amplitudes in planar N=4 super Yang-Mills are given by the volume of the (dual) amplituhedron. In this paper we show some interesting connections between the tree-level amplituhedron and a special class of differential equations. In particular we demonstrate how the amplituhedron volume for NMHV amplitudes is determined by these differential equations. The new formulation allows for a straightforward geometric description, without any reference to triangulations. Finally we discuss possible implications for volumes related to generic N^kMHV amplitudes.

  11. Environmental chemistry: Volume A

    Energy Technology Data Exchange (ETDEWEB)

    Yen, T.F.

    1999-08-01

    This is an extensive introduction to environmental chemistry for engineering and chemical professionals. The contents of Volume A include a brief review of basic chemistry prior to coverage of litho, atmo, hydro, pedo, and biospheres.

  12. Cooking the volumes

    OpenAIRE

    Sparavigna, Amelia Carolina

    2012-01-01

    Cooking possesses a system of units of measurement, that includes measures of volumes based on pre-metric units. This paper discusses the cooking measures and compares their features with those of the ancient Roman measures of capacity.

  13. Integers annual volume 2013

    CERN Document Server

    Landman, Bruce

    2014-01-01

    ""Integers"" is a refereed online journal devoted to research in the area of combinatorial number theory. It publishes original research articles in combinatorics and number theory. This work presents all papers of the 2013 volume in book form.

  14. Free volume under shear

    Science.gov (United States)

    Maiti, Moumita; Vinutha, H. A.; Sastry, Srikanth; Heussinger, Claus

    2015-10-01

    Using an athermal quasistatic simulation protocol, we study the distribution of free volumes in sheared hard-particle packings close to, but below, the random-close packing threshold. We show that under shear, and independent of volume fraction, the free volumes develop features similar to close-packed systems — particles self-organize in a manner as to mimick the isotropically jammed state. We compare athermally sheared packings with thermalized packings and show that thermalization leads to an erasure of these structural features. The temporal evolution in particular the opening-up and the closing of free-volume patches is associated with the single-particle dynamics, showing a crossover from ballistic to diffusive behavior.

  15. Innovation in gynaecological brachytherapy: new technologies, pulse dose-rate brachytherapy, image, definition of new volumes of interest and their impact on dosimetry: application in a clinical research programme 'S.T.I.C.'

    International Nuclear Information System (INIS)

    Brachytherapy plays a fundamental role in the therapeutic approach of patients with stage I-IV cervical carcinoma. Technical modalities have evolved during the last decades: stepping source technology, imaging modalities development, specially IMN, treatment planning system integrating 3D images. Images from CT-Scan and MRI have contributed to a better knowledge of tumoral extension and critical organs. CT and/or MRI compatible applicators allow a sectional image based approach with a better definition of tumour volume compared to traditional approaches. The introduction of 3D image based approach for GTV and CTV requires new definitions and a common language. In 2000, a working group within GEC-ESTRO was created to support 3D image based 3D treatment planning approach in cervix cancer BT. The task was to determine a common terminology enabling various groups to use a common language. Recommendations were described and proposed based on clinical experience and dosimetric concepts of different institutions. Two CTVs were described en relation to the risk for recurrence: high-risk CTV and intermediate risk CTV. In order to better define the role of such definitions and their potential impact on the complication incidence in patients with cervical cancer, a special French programme was developed. The aim of this programme is to study the incidence of the severe 2-year complication rate in two comparable patient populations: one population is treated using PDR brachytherapy with CT-Scan or MRI with the applicators in place allowing a 3D dosimetry with optimization, the second population is treated using standard X-rays radiographs, without any delineation of the target nor optimisation. Each population arm includes 425 patients. A medico-economic assessment is performed, allowing a real cost of the most sophisticated approach compared to a historical dosimetric system. (author)

  16. [Innovation in gynaecological brachytherapy: new technologies, pulse dose-rate brachytherapy, image, definition of new volumes of interest and their impact on dosimetry: application in a clinical research programme "STIC"].

    Science.gov (United States)

    Haie-Meder, C; Peiffert, D

    2006-11-01

    Brachytherapy plays a fundamental role in the therapeutic approach of patients with stage I-IV cervical carcinoma. Technical modalities have evolved during the last decades: stepping source technology, imaging modalities development, specially IMN, treatment planning system integrating 3D images. Images from CT-Scan and MRI have contributed to a better knowledge of tumoral extension and critical organs. CT and/or MRI compatible applicators allow a sectional image based approach with a better definition of tumour volume compared to traditional approaches. The introduction of 3D image based approach for GTV and CTV requires new definitions and a common language. In 2000, a working group within GEC-ESTRO was created to support 3D image based 3D treatment planning approach in cervix cancer BT. The task was to determine a common terminology enabling various groups to use a common language. Recommendations were described and proposed based on clinical experience and dosimetric concepts of different institutions. Two CTVs were described en relation to the risk for recurrence: high-risk CTV and intermediate risk CTV. In order to better define the role of such definitions and their potential impact on the complication incidence in patients with cervical cancer, a special French programme was developed. The aim of this programme is to study the incidence of the severe 2-year complication rate in two comparable patient populations: one population is treated using PDR brachytherapy with CT-Scan or MRI with the applicators in place allowing a 3D dosimetry with optimization, the second population is treated using standard X-rays radiographs without any delineation of the target nor optimisation. Each population arm includes 425 patients. A medicoeconomic assessment is performed, allowing a real cost of the most sophisticated approach compared to a historical dosimetric system.

  17. Application of partial pressure type oxygen sensor in oxygen volume fraction measurement%分压型氧传感器在氧气体积分数测量中的应用

    Institute of Scientific and Technical Information of China (English)

    卢灿; 叶结伢; 孙帮东; 周晓丹

    2009-01-01

    The composition of oxygen volume fraction measurement system with partial pressure type oxygen sensor is introduced, the structure and the application method of the sensor are discussed also. The signal processing and detection method of partial pressure type oxygen sensor and ambient pressure sensor are presented, as well as the design of control circuits. The measurement precision of the system precedes ±1 % FS at the room temperature, ±2 % FS at ambient temperature -55 ~70℃ by test. The system works stably and the precision excursion is less than ±1 % within 1000 h life test at 70 ℃ ambient temperature.%介绍了采用分压型氧传感器的氧气体积分数测量系统的构成,讨论了分压型氧传感器结构和应用方法.给出了分压型氧传感器和环境压力传感器的信号处理和检测方法,以及控制电路的设计.经过测试,系统在室温环境下测量精度优于±1%FS,-55~70℃范围内优于±2%FS.在70℃环境下1000h寿命试验中,工作稳定,精度漂移量小于±1%.

  18. 决策树算法在团购商品销售预测中的应用%Application of Sales Volume Forecast of Group Purchase Based on Decision Tree Method

    Institute of Scientific and Technical Information of China (English)

    费斐; 叶枫

    2013-01-01

      网络团购,指的是互相不认识的消费者在特定的时间内在同一网站上共同购买同一种商品,以求得最优价格的一种网络购物方式。现如今,作为平台方的团购网站在面对大量报名参加团购的商品,审核过程中需要介入大量人力,对经验过于依赖。利用决策树算法,对影响团购商品销量水平的变量进行分析,生成可读的决策树,用以辅助决策,筛选出优质的商品。%Group purchase is a shopping mode that customers buying goods which been selling at a discount in a limited period of time and specific website. Nowadays, facing the large number of application of commodity. Group purchase website as a Platform, which has to intervene a lot of manpower for product review. Also may excessively dependent on the former experience. This paper intends to use the decision tree algorithm to analyse the sales volume of the group purchase goods. Generate readable decision tree to make a strategic decision and select the high quality goods.

  19. Generalized Partial Volume

    DEFF Research Database (Denmark)

    Darkner, Sune; Sporring, Jon

    2011-01-01

    Mutual Information (MI) and normalized mutual information (NMI) are popular choices as similarity measure for multimodal image registration. Presently, one of two approaches is often used for estimating these measures: The Parzen Window (PW) and the Generalized Partial Volume (GPV). Their theoret......Mutual Information (MI) and normalized mutual information (NMI) are popular choices as similarity measure for multimodal image registration. Presently, one of two approaches is often used for estimating these measures: The Parzen Window (PW) and the Generalized Partial Volume (GPV...

  20. Volume anomaly in ferrimagnetism

    OpenAIRE

    Pascard, H.; Globus, A.

    1981-01-01

    The volume anomaly ΔV/V due to the magnetic energy corresponding to the exchange interactions is experimentally determined for YIG. The experimental values (from 77 K to Tc) agree with the values deduced from the theoretical expression based on the Néel's theories of volume anomaly and of ferrimagnetism. These results are compared with those obtained by other authors on ferromagnetic and antiferromagnetic materials with localized magnetic moments : a reduced curve is obtained.

  1. New volume and inverse volume operators for loop quantum gravity

    OpenAIRE

    Yang, Jinsong; Ma, Yongge

    2016-01-01

    A new alternative volume operator is constructed for loop quantum gravity by using the so-called co-triad operators as building blocks. It is shown that the new volume operator shares the same qualitative properties with the standard volume operator. Moreover, a new alternative inverse volume operator is also constructed in the light of the construction of the alternative volume operator, which is possessed of the same qualitative properties as those of the alternative volume operator. The ne...

  2. Drishti: a volume exploration and presentation tool

    Science.gov (United States)

    Limaye, Ajay

    2012-10-01

    Among several rendering techniques for volumetric data, direct volume rendering is a powerful visualization tool for a wide variety of applications. This paper describes the major features of hardware based volume exploration and presentation tool - Drishti. The word, Drishti, stands for vision or insight in Sanskrit, an ancient Indian language. Drishti is a cross-platform open-source volume rendering system that delivers high quality, state of the art renderings. The features in Drishti include, though not limited to, production quality rendering, volume sculpting, multi-resolution zooming, transfer function blending, profile generation, measurement tools, mesh generation, stereo/anaglyph/crosseye renderings. Ultimately, Drishti provides an intuitive and powerful interface for choreographing animations.

  3. Reachable volume RRT

    KAUST Repository

    McMahon, Troy

    2015-05-01

    © 2015 IEEE. Reachable volumes are a new technique that allows one to efficiently restrict sampling to feasible/reachable regions of the planning space even for high degree of freedom and highly constrained problems. However, they have so far only been applied to graph-based sampling-based planners. In this paper we develop the methodology to apply reachable volumes to tree-based planners such as Rapidly-Exploring Random Trees (RRTs). In particular, we propose a reachable volume RRT called RVRRT that can solve high degree of freedom problems and problems with constraints. To do so, we develop a reachable volume stepping function, a reachable volume expand function, and a distance metric based on these operations. We also present a reachable volume local planner to ensure that local paths satisfy constraints for methods such as PRMs. We show experimentally that RVRRTs can solve constrained problems with as many as 64 degrees of freedom and unconstrained problems with as many as 134 degrees of freedom. RVRRTs can solve problems more efficiently than existing methods, requiring fewer nodes and collision detection calls. We also show that it is capable of solving difficult problems that existing methods cannot.

  4. Innovation in gynaecological brachytherapy: new technologies, pulse dose-rate brachytherapy, image, definition of new volumes of interest and their impact on dosimetry: application in a clinical research programme 'S.T.I.C.'; Nouveautes en curietherapie gynecologique: nouvelles technologies, curietherapie pulsee, imagerie, definitions de nouveaux volumes d'interet et leur impact sur la dosimetrie: applications dans le cadre d'un STIC

    Energy Technology Data Exchange (ETDEWEB)

    Haie-Meder, C. [Institut Gustave-Roussy, Service de Curietherapie, 94 - Villejuif (France); Peiffert, D. [Centre Alexis-Vautrin, Service de Radiotherapie, 54 - Vandoeuvre-Les-Nancy (France)

    2006-11-15

    Brachytherapy plays a fundamental role in the therapeutic approach of patients with stage I-IV cervical carcinoma. Technical modalities have evolved during the last decades: stepping source technology, imaging modalities development, specially IMN, treatment planning system integrating 3D images. Images from CT-Scan and MRI have contributed to a better knowledge of tumoral extension and critical organs. CT and/or MRI compatible applicators allow a sectional image based approach with a better definition of tumour volume compared to traditional approaches. The introduction of 3D image based approach for GTV and CTV requires new definitions and a common language. In 2000, a working group within GEC-ESTRO was created to support 3D image based 3D treatment planning approach in cervix cancer BT. The task was to determine a common terminology enabling various groups to use a common language. Recommendations were described and proposed based on clinical experience and dosimetric concepts of different institutions. Two CTVs were described en relation to the risk for recurrence: high-risk CTV and intermediate risk CTV. In order to better define the role of such definitions and their potential impact on the complication incidence in patients with cervical cancer, a special French programme was developed. The aim of this programme is to study the incidence of the severe 2-year complication rate in two comparable patient populations: one population is treated using PDR brachytherapy with CT-Scan or MRI with the applicators in place allowing a 3D dosimetry with optimization, the second population is treated using standard X-rays radiographs, without any delineation of the target nor optimisation. Each population arm includes 425 patients. A medico-economic assessment is performed, allowing a real cost of the most sophisticated approach compared to a historical dosimetric system. (author)

  5. Application of automated volume scanner system in varicose vein of lower limbs%超声自动容积断层成像在下肢静脉曲张中的应用

    Institute of Scientific and Technical Information of China (English)

    朱隽; 陈悦; 朱绫琳; 庞芸; 陈林; 詹嘉; 柴启亮

    2011-01-01

    Objective To explore the application value of automated volume scanner system (AVSS) in varicose vein of lower limbs. Methods AVSS and 2D gray-scale ultrasonography were used to examine 45 varicose veins of lower limbs in 32 patients, and the features were analyzed in transactional and sagittal plane of the traditional gray-scale images, especially in skin-coronal plane patterns after obtaining the full volume images. Resnlts AVSS clearly indicated the characteristics of 45 varicose veins of lower limbs in skin-coronal plane patterns, including 35 simple varicose veins, 7 varicose veins with an-eurysmal dilatation, 5 with segmental venous thrombosis and 2 with both aneurysmal dilatation and segmental venous thrombosis. The detection rate of circuitous veins with AVSS was significantly higher than that with 2D gray-scale ultrasonography (P<0. 001). Conclusion AVSS can intuitively evaluate the development of the lower limb veins, and judge the function of venous valves combining traditional color Doppler flow image, which can provide important preoperative information.%目的 探讨超声自动容积断层成像系统(AVSS)在下肢静脉曲张中的应用价值.方法 分别对32例患者、45条下肢曲张静脉进行传统矢状面横切、纵切扫查和超声自动容积断层扫描,获得容积成像信息,观察并重点对表皮冠状面图像进行研究分析.结果 自动容积断层扫描显示45条曲张下肢静脉中,35条为单纯静脉曲张,7条合并瘤样扩张,5条伴有节段性静脉血栓形成,其中2条同时伴瘤样扩张和静脉血栓形成,病变均在AVSS表皮冠状面成像上清晰显示.AVSS纡曲静脉检出率明显高于二维灰阶超声(P<0.001).结论 超声AVSS可以整体直观评估下肢静脉的发病情况,结合传统彩色超声判断静脉瓣功能可为术前提供重要信息.

  6. New methods to interpolate large volume of data from points or particles (Mesh-Free) methods application for its scientific visualization; Nuevos metodos de interpolacion de grandes volumenes de datos provenientes de la aplicacion de los metodos de particulas o puntos (libre de malla) para su visualizacion cientifica

    Energy Technology Data Exchange (ETDEWEB)

    Reyes Lopez, Y.; Yervilla Herrera, H.; Viamontes Esquivel, A.; Recarey Morfa, C. A.

    2009-07-01

    In the following paper we developed a new method to interpolate large volumes of scattered data, focused mainly on the results of the Mesh free Methods, Points Methods and the Particles Methods application. Through this one, we use local radial basis function as interpolating functions. We also use over-tree as the data structure that allows to accelerate the localization of the data that influences to interpolate the values at a new point, speeding up the application of scientific visualization techniques to generate images from large data volumes from the application of Mesh-free Methods, Points and Particle Methods, in the resolution of diverse models of physics-mathematics. As an example, the results obtained after applying this method using the local interpolation functions of Shepard are shown. (Author) 22 refs.

  7. Volumes of chain links

    CERN Document Server

    Kaiser, James; Rollins, Clint

    2011-01-01

    Agol has conjectured that minimally twisted n-chain links are the smallest volume hyperbolic manifolds with n cusps, for n at most 10. In his thesis, Venzke mentions that these cannot be smallest volume for n at least 11, but does not provide a proof. In this paper, we give a proof of Venzke's statement. The proof for n at least 60 is completely rigorous. The proof for n between 11 and 59 uses a computer calculation, and can be made rigorous for manifolds of small enough complexity, using methods of Moser and Milley. Finally, we prove that the n-chain link with 2m or 2m+1 half-twists cannot be the minimal volume hyperbolic manifold with n cusps, provided n is at least 60 or |m| is at least 8, and we give computational data indicating this remains true for smaller n and |m|.

  8. HARNESSING BIG DATA VOLUMES

    Directory of Open Access Journals (Sweden)

    Bogdan DINU

    2014-04-01

    Full Text Available Big Data can revolutionize humanity. Hidden within the huge amounts and variety of the data we are creating we may find information, facts, social insights and benchmarks that were once virtually impossible to find or were simply inexistent. Large volumes of data allow organizations to tap in real time the full potential of all the internal or external information they possess. Big data calls for quick decisions and innovative ways to assist customers and the society as a whole. Big data platforms and product portfolio will help customers harness to the full the value of big data volumes. This paper deals with technical and technological issues related to handling big data volumes in the Big Data environment.

  9. Aperiodic Volume Optics

    Science.gov (United States)

    Gerke, Tim D.

    Presented in this thesis is an investigation into aperiodic volume optical devices. The three main topics of research and discussion are the aperiodic volume optical devices that we call computer-generated volume holograms (CGVH), defects within periodic 3D photonic crystals, and non-periodic, but ordered 3D quasicrystals. The first of these devices, CGVHs, are designed and investigated numerically and experimentally. We study the performance of multi-layered amplitude computer-generated volume holograms in terms of efficiency and angular/frequency selectivity. Simulation results show that such aperiodic devices can increase diffraction efficiency relative to periodic amplitude volume holograms while maintaining angular and wavelength selectivity. CGVHs are also designed as voxelated volumes using a new projection optimization algorithm. They are investigated using a volumetric diffraction simulation and a standard 3D beam propagation technique as well as experimentally. Both simulation and experiment verify that the structures function according to their design. These represent the first diffractive structures that have the capacity for generating arbitrary transmission and reflection wave fronts and that provide the ability for multiplexing arbitrary functionality given different illumination conditions. Also investigated and discussed in this thesis are 3D photonic crystals and quasicrystals. We demonstrate that these devices can be fabricated using a femtosecond laser direct writing system that is particularly appropriate for fabrication of such arbitrary 3D structures. We also show that these devices can provide 3D partial bandgaps which could become complete bandgaps if fabricated using high index materials or by coating lower index materials with high index metals. Our fabrication method is particularly suited to the fabrication of engineered defects within the periodic or quasi-periodic systems. We demonstrate the potential for fabricating defects within

  10. Volume holographic memory

    Directory of Open Access Journals (Sweden)

    Cornelia Denz

    2000-05-01

    Full Text Available Volume holography represents a promising alternative to existing storage technologies. Its parallel data storage leads to high capacities combined with short access times and high transfer rates. The design and realization of a compact volume holographic storage demonstrator is presented. The technique of phase-coded multiplexing implemented to superimpose many data pages in a single location enables to store up to 480 holograms per storage location without any moving parts. Results of analog and digital data storage are shown and real time optical image processing is demonstrated.

  11. Analytic varieties with finite volume amoebas are algebraic

    CERN Document Server

    Madani, Farid

    2011-01-01

    In this paper, we study the amoeba volume of a given $k-$dimensional generic analytic variety $V$ of the complex algebraic torus $(\\C^*)^n$. When $n\\geq 2k$, we show that $V$ is algebraic if and only if the volume of its amoeba is finite. In this precise case, we establish a comparison theorem for the volume of the amoeba and the coamoeba. Examples and applications to the $k-$linear spaces will be given.

  12. NUMERICAL INTEGRATION IN VOLUME CALCULATION OF IRREGULAR ANTICLINES

    OpenAIRE

    Tomislav Malvić; Rajna Rajić; Petra Slavinić; Kristina Novak Zelenika

    2014-01-01

    The volume of geological structures is often calculated by using the definite integral. Though in some cases the integral can be solved analytically, in practice we usually approximate its value by numerical integration techniques. The application of definite integral in volume calculation is illustrated by two examples. The volume of Mount Fuji, the world-known “conic” geomorphological structure, is calculated by analytical integration. Two basic numerical integration methods, that is, the t...

  13. 自动乳腺全容积成像技术诊断乳腺病灶的研究进展%Research Progress in Application of Automated Breast Volume Scanner in Diagnosis of Breast Lesions

    Institute of Scientific and Technical Information of China (English)

    何其佳; 赵玉珍

    2015-01-01

    Early screening, diagnosis and treatment of breast cancers play a key role in reduction of the mortality and improvement of the survival rate for patients with breast cancers. Through summarization of the related domestic and overseas literature, this paper compared the automated breast volume scanner (ABVS) with conventional ultrasound, elasticity imaging, breast molybdenum target mammography from four perspectives including the lesion detection rate, accuracy, sensitivity and speciifcity. Additionally, the features of coronal ABVS images of benign and malignant breast lesions were also analyzed, such as the convergence sign, high echo ring, micro calciifcation,etc. Finally, it summarized the advantages and disadvantages of application of ABVS in diagnosis of breast cancers, which offered reliable references for its wider clinical popularity.%乳腺癌早期筛查及诊治是降低乳腺癌患者病死率和提高其生存率的关键。本文通过总结归纳国内外文献资料,对比分析自动乳腺全容积成像(ABVS)与普通超声、弹性成像、乳腺钼靶的病灶检出率、诊断准确度、敏感度、特异度,分析乳腺良恶性病灶的ABVS冠状面图像特征,总结ABVS诊断乳腺肿物的优势和不足,为其推广运用于临床提供可靠依据。

  14. Live ultrasound volume reconstruction using scout scanning

    Science.gov (United States)

    Meyer, Amelie; Lasso, Andras; Ungi, Tamas; Fichtinger, Gabor

    2015-03-01

    Ultrasound-guided interventions often necessitate scanning of deep-seated anatomical structures that may be hard to visualize. Visualization can be improved using reconstructed 3D ultrasound volumes. High-resolution 3D reconstruction of a large area during clinical interventions is challenging if the region of interest is unknown. We propose a two-stage scanning method allowing the user to perform quick low-resolution scouting followed by high-resolution live volume reconstruction. Scout scanning is accomplished by stacking 2D tracked ultrasound images into a low-resolution volume. Then, within a region of interest defined in the scout scan, live volume reconstruction can be performed by continuous scanning until sufficient image density is achieved. We implemented the workflow as a module of the open-source 3D Slicer application, within the SlicerIGT extension and building on the PLUS toolkit. Scout scanning is performed in a few seconds using 3 mm spacing to allow region of interest definition. Live reconstruction parameters are set to provide good image quality (0.5 mm spacing, hole filling enabled) and feedback is given during live scanning by regularly updated display of the reconstructed volume. Use of scout scanning may allow the physician to identify anatomical structures. Subsequent live volume reconstruction in a region of interest may assist in procedures such as targeting needle interventions or estimating brain shift during surgery.

  15. Product formulas for volumes of flow polytopes

    CERN Document Server

    Meszaros, Karola

    2011-01-01

    Intrigued by the product formula prod_{i=1}^{n-2} C_i for the volume of the Chan-Robbins-Yuen polytope CRY_n, where C_i is the ith Catalan number, we construct a family of polytopes P_{m,n}, whose volumes are given by the product \\prod_{i=m+1}^{m+n-2}\\frac{1}{2i+1}{{m+n+i} \\choose {2i}}. The Chan-Robbins-Yuen polytope CRY_n coincides with P_{0,n-1}. Our construction of the polytopes P_{m,n} is an application of a systematic method we develop for expressing volumes of a class of flow polytopes as the number of certain triangular arrays. This method can also be used as a heuristic technique for constructing polytopes with combinatorial volumes. As an illustration of this we construct polytopes whose volumes equal the number of r-ary trees on n internal nodes, \\frac{1}{(r-1)n+1} {{rn} \\choose n}. Using triangular arrays we also express the volumes of flow polytopes as constant terms of formal Laurent series.

  16. Topology optimization using the finite volume method

    DEFF Research Database (Denmark)

    Computational procedures for topology optimization of continuum problems using a material distribution method are typically based on the application of the finite element method (FEM) (see, e.g. [1]). In the present work we study a computational framework based on the finite volume method (FVM, see...... the well known Reuss lower bound. [1] Bendsøe, M.P.; Sigmund, O. 2004: Topology Optimization - Theory, Methods, and Applications. Berlin Heidelberg: Springer Verlag [2] Versteeg, H. K.; W. Malalasekera 1995: An introduction to Computational Fluid Dynamics: the Finite Volume Method. London: Longman......, e.g. [2]) in order to develop methods for topology design for applications where conservation laws are critical such that element--wise conservation in the discretized models has a high priority. This encompasses problems involving for example mass and heat transport. The work described...

  17. Design for volume reduction

    NARCIS (Netherlands)

    Wever, R.; Boks, C.; Stevels, A.

    2007-01-01

    Traditionally packaging design-for-sustainability (DfS) strongly focuses on resource conservation and material recycling. The type and amount of materials used has been the driver in design. For consumer electronics (CE) products this weight-based approach is too limited; a volume-based approach is

  18. Introduction to the Volume.

    Science.gov (United States)

    Emihovich, Catherine; Schroder, Barbara; Panofsky, Carolyn P.

    1999-01-01

    Introduces a volume that examines the issue of critical thinking and whether or not it is culturally specific, discussing recent research on the subject. The papers focus on critical thinking and culture, historical consciousness and critical thinking, critical thinking as cultural-historical practice, culture and the development of critical…

  19. Microwave power engineering applications

    CERN Document Server

    Okress, Ernest C

    2013-01-01

    Microwave Power Engineering, Volume 2: Applications introduces the electronics technology of microwave power and its applications. This technology emphasizes microwave electronics for direct power utilization and transmission purposes. This volume presents the accomplishments with respect to components, systems, and applications and their prevailing limitations in the light of knowledge of the microwave power technology. The applications discussed include the microwave heating and other processes of materials, which utilize the magnetron predominantly. Other applications include microwave ioni

  20. 10 CFR 590.208 - Small volume exports.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Small volume exports. 590.208 Section 590.208 Energy... WITH RESPECT TO THE IMPORT AND EXPORT OF NATURAL GAS Applications for Authorization To Import or Export Natural Gas § 590.208 Small volume exports. Any person may export up to 100,000 cubic feet of natural...

  1. Computer vision technology in log volume inspection

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Log volume inspection is very important in forestry research and paper making engineering. This paper proposed a novel approach based on computer vision technology to cope with log volume inspection. The needed hardware system was analyzed and the details of the inspection algorithms were given. A fuzzy entropy based on image enhancement algorithm was presented for enhancing the image of the cross-section of log. In many practical applications the cross-section is often partially invisible, and this is the major obstacle for correct inspection. To solve this problem, a robust Hausdorff distance method was proposed to recover the whole cross-section. Experiment results showed that this method was efficient.

  2. Application of stroke volume variation in directing management of elderly septic shock patients%每搏量变异度在老年脓毒性休克患者中的应用

    Institute of Scientific and Technical Information of China (English)

    王志; 汤卫兵; 刘野

    2015-01-01

    目的:探讨每搏量变异度(SVV)在老年脓毒性休克患者中的应用。方法将进行机械通气的老年脓毒性休克患者28例分为常规组13例和SVV指导组15例,常规组根据中心静脉压(CVP)指导容量复苏,SVV指导组根据SVV、心输出量(CO)指导容量复苏。观察2组患者复苏时间、复苏后血乳酸、氧合指数、CVP、平均动脉压(MAP)、N端尿钠肽前体(NT-proB⁃NP)等变化,机械通气时间、24 h内左心功能不全发生率,28 d发生多器官功能障碍综合征(MODS)和死亡情况,记录SVV指导组复苏前后血流动力学参数SVV、CO、外周血管阻力(SVR)的变化。结果 SVV指导组复苏时间短于常规组(t=3.83),乳酸、NT-proBNP较常规组下降(t分别为3.20和12.32,P<0.05),氧合指数较常规组升高(t=3.01,P<0.05)。2组左心功能不全、MODS及病死率差异无统计学意义(P分别为0.198、0.410和0.372)。SVV指导组复苏后CO、SVV较复苏前改善(P<0.05)。结论 SVV能更好地指导老年脓毒性休克患者的容量复苏。%Objective To investigate the application of stroke volume variation (SVV) in directing management of elderly septic shock patients. Methods Patients who were diagnosed with elderly septic shock and supported with mechanical ventilation were in⁃cluded (n=28). They were divided into control group (n=13) and SVV group (n=15). Volume recovery was directed by CVP (central ve⁃nous pressure ) in control group and by SVV and CO (cardiac output) in SVV guoup respectively. Blood lactate, oxidation index, CVP , MVP, NT-proBNP, time of recovery, the length relying on mechanical ventilation and Vigileo parameters were compared after volume resuscition. During the period of treatment, the incidence of acute left ventricle dysfunction within 24 hours, MODS within 28 days and mortality rates of all causes were compared between these two groups. Changes in SVV, cardiac output (CO) and

  3. Polar Mohr diagram method and its application in calculating the shear displacements of general shear zones with volume loss--With the Sangshuyuanzi ductile shear zone as an example

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The main problem,in determining the shear displacement of a general shear zone with volume change using the available formula,is that it is hard to know the initial angle between the planes (or lines) in the plane of shear.A planar deformation analysis of this kind of ductile shear zone is carried out with the polar Mohr diagram.If the volume change is induced by homogeneous contraction in the Z direction of the shear zone,there are sufficient conditions for constructing a polar Mohr diagram regardless of sequence of the simple shear and volume change.Therefore,the angle between a line and the shear direction before and after the deformation can be measured.Making use of these lines the shear strain and the volume change can be calculated and the shear displacement can be determined.

  4. Polar Mohr diagram method and its application in calculating the shear displacements of general shear zones with volume loss——With the Sangshuyuanzi ductile shear zone as an example

    Institute of Scientific and Technical Information of China (English)

    李海; 郭召杰; 刘瑞洵; 刘树文; 张志诚

    2000-01-01

    The main problem, in determining the shear displacement of a general shear zone with volume change using the available formula, is that it is hard to know the initial angle between the planes (or lines) in the plane of shear. A planar deformation analysis of this kind of ductile shear zone is carried out with the polar Mohr diagram. If the volume change is induced by homogeneous contraction in the Z direction of the shear zone, there are sufficient conditions for constructing a polar Mohr diagram regardless of sequence of the simple shear and volume change. Therefore, the angle between a line and the shear direction before and after the deformation can be measured. Making use of these lines the shear strain and the volume change can be calculated and the shear displacement can be determined.

  5. Assistência de ar e volumes de aplicação na deposição de calda e no controle do arroz vermelho (Oryza sativa L. Air assistance and volume of application in spray deposition and in red rice control (Oryza sativa L.

    Directory of Open Access Journals (Sweden)

    Leopoldo L. S. Vigano

    2007-12-01

    Full Text Available O trabalho teve como objetivo avaliar o efeito da assistência de ar junto à barra pulverizadora e de três volumes de pulverização na dessecação e deposição da calda em arroz vermelho, sob cultivo de nabo forrageiro, em áreas de recuperação de várzeas, utilizando o herbicida paraquat e o corante Azul Brilhante, respectivamente. Os volumes de pulverização foram 100; 200 e 300 L ha-1 da solução aquosa, contendo corante alimentício (1.500 mg L-1. Com ou sem a assistência de ar junto à barra, foram utilizadas pontas de pulverização de jato plano tipo AXI 110015 à pressão de 117,3 kPa, AXI 11002 e AXI 11003 a 276 kPa. A avaliação da deposição da pulverização deu-se em folhas de plantas de arroz vermelho. Os maiores volumes (200 e 300 L ha-1 pulverizados com a assistência de ar junto à barra pulverizadora proporcionaram maiores depósitos do corante em relação ao volume de 100 L ha-1. Não foram constatadas diferenças na deposição do corante para os volumes pulverizados, sem a assistência de ar junto à barra, tampouco entre os volumes de 200 e 300 L ha-1 com a assistência de ar junto à barra. As maiores percentagens de controle do arroz vermelho foram obtidas com a assistência de ar junto à barra, independentemente do volume pulverizado, equivalendo-se ao controle obtido com 300 L ha-1, sem o uso dessa tecnologia.The aim of this research was to evaluate the effect of air-assistance on spraying at three volumes in spray deposition and control of red rice under fodder radish cultivation. To evaluate the control of this weed and spray deposition were used paraquat herbicide and a Brilliant Blue dye, respectively. The three spraying volumes were 100, 200 and 300 L ha-1, using a tracer dye at 1,500 mg L-1. Both solutions and volumes were sprayed with flat fan nozzles AXI 110015 at 117.3 kPa, AXI 11002 and AXI 11003 at 276 kPa, respectively, with and without air-assistance on the boom. The evaluation of deposition

  6. An Accurate Volume Measurement of Solid Lesions by correcting Partial Volume Effects on CT images

    Directory of Open Access Journals (Sweden)

    Bitty S. Varghese

    2016-06-01

    Full Text Available Under digital image processing, medical images have lots of applications like oncological diagnosis of tumors and chemotherapy. Computed Tomography (CT images are used to capture images of solid lesions like lung or liver. For oncological chemotherapy based therapeutics, estimation of size of tumor is the main task to determine whether the treatment is in right path or not. This means that, after chemotherapy, tumor either grows or shrinks. Due to irregular growth of tumor, diameter of tumor is not a standard parameter to determine the size. Volume is the appropriate method to identify the size. But partial volume artifacts, which arise due to low resolution of imaging device, reduces the accuracy of measurement. Partial volume correction (PVC which extracts the necessary information from the segmented output resolves this problem. This paper presents a different perspective of accurate volumetric measurement by correcting partial volume effect at the borders of segmentation result.

  7. Postoperative volume balance

    DEFF Research Database (Denmark)

    Frost, H; Mortensen, C.R.; Secher, N H;

    2016-01-01

    In healthy humans, stroke volume (SV) and cardiac output (CO) do not increase with expansion of the central blood volume by head-down tilt or administration of fluid. Here, we exposed 85 patients to Trendelenburg's position about one hour after surgery while cardiovascular variables were determined...... non-invasively by Modelflow. In Trendelenburg's position, SV (83 ± 19 versus 89 ± 20 ml) and CO (6·2 ± 1·8 versus 6·8 ± 1·8 l/min; both P... (39%) with a > 10% increase in SV (from 78 ± 16 to 90 ± 17 ml) corresponding to an increase in CO from 5·9 ± 1·5 to 6·9 ± 1·6 l min(-1) (Phead-down, administration of 250 ml Ringer's lactate solution increased SV (to 88 ± 18 ml) and CO (to 6·8 ± 1·7 l min(-1) ). In conclusion...

  8. Mean nuclear volume

    DEFF Research Database (Denmark)

    Mogensen, O.; Sørensen, Flemming Brandt; Bichel, P.;

    1999-01-01

    We evaluated the following nine parameters with respect to their prognostic value in females with endometrial cancer: four stereologic parameters [mean nuclear volume (MNV), nuclear volume fraction, nuclear index and mitotic index], the immunohistochemical expression of cancer antigen (CA125...... included total abdominal hysterectomy and bilateral salpingo-oophorectomy. All patients underwent radical operations. The tumors were classified postsurgically as P-stage I-III. All patients received the same postoperative radiation therapy. The surviving patients were observed for a median of 6.4 years...... (range 5.0-8.4 years). Cox regression analysis (automatic forward selection) showed the MNV to be the most significant prognostic parameter followed by the P-stage. Patients who had localized tumors or tumors with small nuclei had a better probability of surviving than did women with advanced tumors...

  9. Mixed volumes of hypersimplices

    OpenAIRE

    Liu, Gaku

    2014-01-01

    In this paper we consider mixed volumes of combinations of hypersimplices. These numbers, called "mixed Eulerian numbers", were first considered by A. Postnikov and were shown to satisfy many properties related to Eulerian numbers, Catalan numbers, binomial coefficients, etc. We give a general combinatorial interpretation for mixed Eulerian numbers and prove the above properties combinatorially. In particular, we show that each mixed Eulerian number enumerates a certain set of permutations in...

  10. Aplicação de modelos matemáticos na estimativa do volume de bulbo molhado por gotejamento superficial em diferentes tipos de solo Application of mathematical models to estimate the wet soil volume in superficial drip irrigation in different types of soils

    OpenAIRE

    Celsemy Eleutério Maia

    2010-01-01

    A informação do volume de solo molhado pela irrigação localizada é importante para o dimensionamento e manejo da irrigação por gotejamento superficial, bem como para a estimativa da quantidade de água disponível para as plantas. Com o objetivo de avaliar cinco modelos para estimar o volume molhado pela irrigação por gotejamento superficial, foram instalados experimentos em seis tipos de solos (Luvissolo Crômico, Argissolo Vermelho-Amarelo, Cambissolo Háplico, Neossolo Quartzarênico, Latossolo...

  11. Partial Volume Correction in Quantitative Amyloid Imaging

    Science.gov (United States)

    Su, Yi; Blazey, Tyler M.; Snyder, Abraham Z.; Raichle, Marcus E.; Marcus, Daniel S.; Ances, Beau M.; Bateman, Randall J.; Cairns, Nigel J.; Aldea, Patricia; Cash, Lisa; Christensen, Jon J.; Friedrichsen, Karl; Hornbeck, Russ C.; Farrar, Angela M.; Owen, Christopher J.; Mayeux, Richard; Brickman, Adam M.; Klunk, William; Price, Julie C.; Thompson, Paul M.; Ghetti, Bernardino; Saykin, Andrew J.; Sperling, Reisa A.; Johnson, Keith A.; Schofield, Peter R.; Buckles, Virginia; Morris, John C.; Benzinger, Tammie. LS.

    2014-01-01

    Amyloid imaging is a valuable tool for research and diagnosis in dementing disorders. As positron emission tomography (PET) scanners have limited spatial resolution, measured signals are distorted by partial volume effects. Various techniques have been proposed for correcting partial volume effects, but there is no consensus as to whether these techniques are necessary in amyloid imaging, and, if so, how they should be implemented. We evaluated a two-component partial volume correction technique and a regional spread function technique using both simulated and human Pittsburgh compound B (PiB) PET imaging data. Both correction techniques compensated for partial volume effects and yielded improved detection of subtle changes in PiB retention. However, the regional spread function technique was more accurate in application to simulated data. Because PiB retention estimates depend on the correction technique, standardization is necessary to compare results across groups. Partial volume correction has sometimes been avoided because it increases the sensitivity to inaccuracy in image registration and segmentation. However, our results indicate that appropriate PVC may enhance our ability to detect changes in amyloid deposition. PMID:25485714

  12. Volume of a laser-induced microjet

    Science.gov (United States)

    Kawamoto, Sennosuke; Hayasaka, Keisuke; Noguchi, Yuto; Tagawa, Yoshiyuki

    2015-11-01

    Needle-free injection systems are of great importance for medical treatments. In spite of their great potential, these systems are not commonly used. One of the common problems is strong pain caused by diffusion shape of the jet. To solve this problem, the usage of a high-speed highly-focused microjet as needle-free injection system is expected. It is thus crucial to control important indicators such as ejected volume of the jet for its safe application. We conduct experiments to reveal which parameter influences mostly the ejected volume. In the experiments, we use a glass tube of an inner diameter of 500 micro-meter, which is filled with the liquid. One end is connected to a syringe and the other end is opened. Radiating the pulse laser instantaneously vapors the liquid, followed by the generation of a shockwave. We find that the maximum volume of a laser-induced bubble is approximately proportional to the ejected volume. It is also found that the occurrence of cavitation does not affect the ejected volume while it changes the jet velocity.

  13. WYSIWYG (What You See is What You Get) volume visualization.

    Science.gov (United States)

    Guo, Hanqi; Mao, Ningyu; Yuan, Xiaoru

    2011-12-01

    In this paper, we propose a volume visualization system that accepts direct manipulation through a sketch-based What You See Is What You Get (WYSIWYG) approach. Similar to the operations in painting applications for 2D images, in our system, a full set of tools have been developed to enable direct volume rendering manipulation of color, transparency, contrast, brightness, and other optical properties by brushing a few strokes on top of the rendered volume image. To be able to smartly identify the targeted features of the volume, our system matches the sparse sketching input with the clustered features both in image space and volume space. To achieve interactivity, both special algorithms to accelerate the input identification and feature matching have been developed and implemented in our system. Without resorting to tuning transfer function parameters, our proposed system accepts sparse stroke inputs and provides users with intuitive, flexible and effective interaction during volume data exploration and visualization. PMID:22034329

  14. Thermodynamics of the low density excluded volume hadron gas

    CERN Document Server

    Zalewski, Kacper

    2015-01-01

    We discuss the influence of the excluded volume of hadrons on macroscopic variables and thermal parameters of the hadron gas at finite temperature and chemical potential in the low density approximation. Based solely on elementary thermodynamics we show that when the excluded volume grows at constant temperature, pressure, and number of particles, the overall volume increases just as much as the excluded volume, while the entropy and energy remain unchanged. The growth of the chemical potentials is equal to the work needed to create the respective excluded volumes. Consequently, the bulk density functions of a gas with excluded volume are expressed by the corresponding variables in a system of point particles with the shifted chemical potentials. Our results are fully consistent with the previous findings obtained upon applications of more advanced methods of statistical physics. A validity limit for the low density approximation is derived and discussed in the context of the hadron gas created in heavy ion c...

  15. Solving hyperbolic equations with finite volume methods

    CERN Document Server

    Vázquez-Cendón, M Elena

    2015-01-01

    Finite volume methods are used in numerous applications and by a broad multidisciplinary scientific community. The book communicates this important tool to students, researchers in training and academics involved in the training of students in different science and technology fields. The selection of content is based on the author’s experience giving PhD and master courses in different universities. In the book the introduction of new concepts and numerical methods go together with simple exercises, examples and applications that contribute to reinforce them. In addition, some of them involve the execution of MATLAB codes. The author promotes an understanding of common terminology with a balance between mathematical rigor and physical intuition that characterizes the origin of the methods. This book aims to be a first contact with finite volume methods. Once readers have studied it, they will be able to follow more specific bibliographical references and use commercial programs or open source software withi...

  16. STOVL propulsion system volume dynamics approximations

    Science.gov (United States)

    Drummond, Colin K.

    1989-01-01

    Two approaches to modeling turbofan engine component volume dynamics are explored and compared with a view toward application to real-time simulation of short take-off vertical landing (STOVL) aircraft propulsion systems. The first (and most popular) approach considers only heat and mass balances; the second approach includes a momentum balance and substitutes the heat equation with a complete energy balance. Results for a practical test case are presented and discussed.

  17. Dental anatomy portrayed with microscopic volume investigations.

    Science.gov (United States)

    Baumann, M A; Schwebel, T; Kriete, A

    1993-01-01

    The clinical treatment of the root canal of teeth--called endodontics--assumes a precise idea of the spatial arrangement of the anatomy of teeth and their inner structure. By using computer-assisted data acquisition from filmed sequences of histologic serial sections and a special kind of magnetic resonance microscope--the Stray Field Imaging (STRAFI)--volume investigations were carried out using special functions of a newly developed 3D software. Possible applications and future perspectives are discussed.

  18. Calculus Students' Understanding of Volume

    Science.gov (United States)

    Dorko, Allison; Speer, Natasha M.

    2013-01-01

    Researchers have documented difficulties that elementary school students have in understanding volume. Despite its importance in higher mathematics, we know little about college students' understanding of volume. This study investigated calculus students' understanding of volume. Clinical interview transcripts and written responses to volume…

  19. New volume and inverse volume operators for loop quantum gravity

    CERN Document Server

    Yang, Jinsong

    2016-01-01

    A new alternative volume operator is constructed for loop quantum gravity by using the so-called co-triad operators as building blocks. It is shown that the new volume operator shares the same qualitative properties with the standard volume operator. Moreover, a new alternative inverse volume operator is also constructed in the light of the construction of the alternative volume operator, which is possessed of the same qualitative properties as those of the alternative volume operator. The new inverse volume operator can be employed to construct the Hamiltonian operator of matter fields, which may lead to an anomaly-free on shell quantum constraint algebra without any special restriction on the regularization procedure for gravity coupled to matter fields.

  20. New volume and inverse volume operators for loop quantum gravity

    Science.gov (United States)

    Yang, Jinsong; Ma, Yongge

    2016-08-01

    A new alternative volume operator is constructed for loop quantum gravity by using the so-called cotriad operators as building blocks. It is shown that the new volume operator shares the same qualitative properties with the standard volume operator. Moreover, a new alternative inverse volume operator is also constructed in the light of the construction of the alternative volume operator, which is possessed of the same qualitative properties as those of the alternative volume operator. The new inverse volume operator can be employed to construct the Hamiltonian operator of matter fields, which may lead to an anomaly-free on-shell quantum constraint algebra without any special restriction on the regularization procedure for gravity coupled to matter fields.

  1. CT/MRI融合图像在盆腔肿瘤放疗靶区勾画中的应用%Application of CT/MRI Image Fusion in the Delineating of the Gross Tumor Target Volumes in the Radiotherapy for Pelvic Cavity Tumor

    Institute of Scientific and Technical Information of China (English)

    张海南; 汤日杰; 张书旭; 蔡霜

    2011-01-01

    Objective To study the value of application of CT/MRI image fusion in the delineating of the gross tumor target volumes in the radiotherapy for pelvic tumor in the middle-aged and elderly patients. Methods Nineteen patients suffering from pelvic tumor underwent CT and MRI examination within one week.All CT and MRI images were manually transported to the Nucletron PLATO Radiation Treatment Planning System(V 8.0, Philips medical corporation), and CT/MRI images were processed for image fusion.The experienced radiotherapeutic physicians delineated and analyzed the target volume of CT and MRI images, and gross tumor target volume of the CT/MR image fusion. Results The gross tumor target volume of the CT/MR image fusion relative the target volume of CT increased 6.29%,and relative MRI raised 11.84%,CT/MRI image fusion is superior to single CT and MRI image in the delineation of the gross tumor target volume, which was verified by test. Conclusion The technology of CT/MR image fusion can help to confirm target volume for pelvic tumor which will improve the accuracy in demarcating of the gross tumor target volume of pelvic cavity tumor, and promote the diagnosis and treatment of pelvic cavity tumor.%目的 探讨CT/MRI融合图像在中老年盆腔肿瘤放疗靶区(GTV)勾画中的应用价值.方法 19例盆腔肿瘤患者均在1周内分别进行CT、MRI异机非同步扫描.全部CT和MRI图像手工配准后传送至飞利浦公司的PINNACLE V8.0放射治疗计划系统,并进行图像融合.由有经验的放疗科医师对CT靶区、MRI靶区及CT与MR融合图像肿瘤靶区(GTV)进行勾画及评价分析.结果 GTVFUSION相对GTVCT提高了6.29%、相对GTVMRI提高了11.84%,融合图像对GTV的勾画明显优于单独CT图像或MRI图像.结论 CT/MRI图像融合技术有利于盆腔肿瘤靶区的确定,提高了临床对盆腔肿瘤靶区(GTV)勾画的准确率,利于患者的诊治.

  2. Radwaste '86: proceedings volume

    International Nuclear Information System (INIS)

    The volume contains all the papers presented at the above Conference, which was held in Cape Town, South Africa from 7 to 12 September 1986. A total of 55 contributions cover the full spectrum of the theme of the Conference, which was subdivided into four sessions. Conditioning, treatment and management of radioactive waste: 12 papers reporting on experiences in various countries, as well as specialist topics such as the extraction of radioactive contaminants from reactor pool water. Containment, safe handling and long-term integrity of ILLW packages: 2 papers dealing with cask design. Transport and storage of radwaste and spent fuel: 7 papers ranging from broad overviews to specific operations in different parts of the world. Radioactive waste disposal and environmental impact: 32 papers covering topics from site selection, design and operation, to modelling and monitoring studies. South Africa's Vaalputs radioactive waste disposal facility is comprehensively described. The volume is a useful reference for anyone interested in the disposal of radioactive waste, especially in arid environments, as well as its treatment and management prior to disposal, and will appeal to a wide range of disciplines including engineers, geologists, geophysicists, life scientists and environmentalists. Of particular interest would be the intensive studies undertaken in South Africa prior to the establishment of a radioactive waste repository in that country

  3. Volume of an Industrial Autoclave

    Directory of Open Access Journals (Sweden)

    Nicholas Madaffari

    2010-01-01

    Full Text Available We were able to determine the volume of an industrial autoclave sterilization tank using a technique learned in calculus. By measuring the dimensions of the tank and roughly estimating the equation of curvature at the ends of the tank, we were able to revolve half of the end of the tank around the x axis to get its fluid volume. Adding the two volumes of the ends and the volume of the cylindrical portion on the tank yielded the total volume.

  4. Disc volume reduction with percutaneous nucleoplasty in an animal model.

    Directory of Open Access Journals (Sweden)

    Richard Kasch

    Full Text Available STUDY DESIGN: We assessed volume following nucleoplasty disc decompression in lower lumbar spines from cadaveric pigs using 7.1Tesla magnetic resonance imaging (MRI. PURPOSE: To investigate coblation-induced volume reductions as a possible mechanism underlying nucleoplasty. METHODS: We assessed volume following nucleoplastic disc decompression in pig spines using 7.1-Tesla MRI. Volumetry was performed in lumbar discs of 21 postmortem pigs. A preoperative image data set was obtained, volume was determined, and either disc decompression or placebo therapy was performed in a randomized manner. Group 1 (nucleoplasty group was treated according to the usual nucleoplasty protocol with coblation current applied to 6 channels for 10 seconds each in an application field of 360°; in group 2 (placebo group the same procedure was performed but without coblation current. After the procedure, a second data set was generated and volumes calculated and matched with the preoperative measurements in a blinded manner. To analyze the effectiveness of nucleoplasty, volumes between treatment and placebo groups were compared. RESULTS: The average preoperative nucleus volume was 0.994 ml (SD: 0.298 ml. In the nucleoplasty group (n = 21 volume was reduced by an average of 0.087 ml (SD: 0.110 ml or 7.14%. In the placebo group (n = 21 volume was increased by an average of 0.075 ml (SD: 0.075 ml or 8.94%. The average nucleoplasty-induced volume reduction was 0.162 ml (SD: 0.124 ml or 16.08%. Volume reduction in lumbar discs was significant in favor of the nucleoplasty group (p<0.0001. CONCLUSIONS: Our study demonstrates that nucleoplasty has a volume-reducing effect on the lumbar nucleus pulposus in an animal model. Furthermore, we show the volume reduction to be a coblation effect of nucleoplasty in porcine discs.

  5. Nuclear maintenance work volume model

    International Nuclear Information System (INIS)

    This presentation will cover a work volume model, detailing what contributes to a maintenance backlog and demonstrate the impact of these contributing factors on it's reduction. In our quest to achieve sustainable nuclear excellence, we have engaged in many debates over our degree of success in reducing the maintenance backlog at Ontario Power Generation plants. The backlog is a volume of work and a simplified analogy would be to consider it as the water level in a tank. The inflow would be the new work requests/minor work orders not completed by the Fix It Now Team, and the outflow would be the completed work orders. The equilibrium in the tank would be the result of the incoming rate of new work versus the rate of outgoing completed work. We can accommodate increasing levels for short durations, but our success depends on our ability to manage the process and achieving timely long term reduction in backlog. Although everyone seemed to have an understanding for the type of change required, it was difficult to quantify the optimum combination. Increasing the work force always seems to be an obvious choice, along with productivity improvements but there must be careful consideration given to the preventative maintenance program and resource allocation such as Support Staff, Fix It Now Team, Outages, Projects, etc. Various other factors impacting on our work rates would include training loads, sick leave and overtime. A need was identified for some analytical tool that would illustrate if our goals were attainable with our present course of action, and demonstrate what changes needed to be implemented in order to be successful. We developed a model consisting of an Excel spreadsheet that trends the backlog for each maintenance workgroup. The user populates the model with specific historical data for plant resource profiles and work execution. The program generates two sets of charts for each maintenance groups, one for actual data and another for target data. The

  6. Distribution of Functional Liver Volume in Hepatocellular Carcinoma Patients with Portal Vein Tumor Thrombus in the 1st Branch and Main Trunk Using Single Photon Emission Computed Tomography—Application to Radiation Therapy

    Directory of Open Access Journals (Sweden)

    Akira Ikoma

    2011-10-01

    Full Text Available Purpose: To analyze the distribution of functional liver volume (FLV in the margin volume (MV surrounding hepatocellular carcinoma (HCC with portal vein tumor thrombus (PVTT before radiation therapy (RT and to verify the safety of single photon emission computed tomography-based three-dimensional conformal radiotherapy (SPECT-B3DCRT by exploring the relation of FLV in MV to radiation-induced liver disease (RILD. Methods and Materials: Clinical target volume (CTV included main tumor and PVTT, and planning target volume (PTV included CTV with a 10 mm margin. MV was defined as PTV–CTV. FLV ratio in MV was calculated as FLV in MV/MV × 100 (%. The two high-dose beams were planned to irradiate FLV as little as possible. Fifty-seven cases of HCC (26/57, 46%; Child–Pugh grade B with PVTT underwent SPECT-B3DCRT which targeted the CTV to a total dose of 45 Gy/18 fractions. The destructive ratio was defined as radiation induced dysfunctional volume/FLV × 100 (%. Results: We observed a significant negative correlation between FLV ratio in MV and CTV (p < 0.001. Three cases with CTVs of 287, 587 and 1184 cm3 experienced transient RILD. The FLV ratio in MV was highest in patients with RILD: nine patients with CTV of 200–300 cm3, three with CTV of 500–600 cm3, and two with CTV of 1100–1200 cm3. The destructive ratio yielded a mean value of 24.2 ± 1.5%. Conclusions: Radiation planning that takes into account the distribution of FLV appears to result in the least possible RILD.

  7. Distribution of Functional Liver Volume in Hepatocellular Carcinoma Patients with Portal Vein Tumor Thrombus in the 1st Branch and Main Trunk Using Single Photon Emission Computed Tomography—Application to Radiation Therapy

    International Nuclear Information System (INIS)

    To analyze the distribution of functional liver volume (FLV) in the margin volume (MV) surrounding hepatocellular carcinoma (HCC) with portal vein tumor thrombus (PVTT) before radiation therapy (RT) and to verify the safety of single photon emission computed tomography-based three-dimensional conformal radiotherapy (SPECT-B3DCRT) by exploring the relation of FLV in MV to radiation-induced liver disease (RILD). Clinical target volume (CTV) included main tumor and PVTT, and planning target volume (PTV) included CTV with a 10 mm margin. MV was defined as PTV–CTV. FLV ratio in MV was calculated as FLV in MV/MV × 100 (%). The two high-dose beams were planned to irradiate FLV as little as possible. Fifty-seven cases of HCC (26/57, 46%; Child–Pugh grade B) with PVTT underwent SPECT-B3DCRT which targeted the CTV to a total dose of 45 Gy/18 fractions. The destructive ratio was defined as radiation induced dysfunctional volume/FLV × 100 (%). We observed a significant negative correlation between FLV ratio in MV and CTV (p < 0.001). Three cases with CTVs of 287, 587 and 1184 cm3 experienced transient RILD. The FLV ratio in MV was highest in patients with RILD: nine patients with CTV of 200–300 cm3, three with CTV of 500–600 cm3, and two with CTV of 1100–1200 cm3. The destructive ratio yielded a mean value of 24.2 ± 1.5%. Radiation planning that takes into account the distribution of FLV appears to result in the least possible RILD

  8. Assessing the optimal liquid volume to be sprayed on isolated olive trees according to their canopy volumes.

    Science.gov (United States)

    Miranda-Fuentes, A; Llorens, J; Rodríguez-Lizana, A; Cuenca, A; Gil, E; Blanco-Roldán, G L; Gil-Ribes, J A

    2016-10-15

    The application of pesticides to traditional and intensive olive orchards in Southern Spain has led to environmental problems. More specifically, the lack of an accurate, useful criterion to regulate the spray volume in relation to canopy characteristics has led to spray drift and runoff, which are threats to local ecosystems. The aim of this study was to determine the optimal relationship between canopy volume and the spray application volume, called specific spray volume, CV, through laboratory and field trials. In the laboratory trial, 6 specific spray volumes (0.05, 0.08, 0.10, 0.12, 0.15, and 0.20Lm(-3)) were tested in a specially designed structure containing small, live olive trees in order to simulate an intensive plantation system. The model aimed to evaluate the coverage of pesticide application on water sensitive paper (WSP) collectors. In the field trial, the three laboratory specific spray volumes that gave the best coverage values were tested on live, intensively managed trees, whose crown volume was manually measured. Food dye E-102 was used to determine the spray deposition on artificial targets (10×10cm absorbent paper pieces), and WSP was used to evaluate spray coverage. The spray penetration and deposit homogeneity inside the canopy were also evaluated. Weather conditions during the field trial were monitored with a weather station. The results of the laboratory trial showed that the three best specific spray volumes were 0.08, 0.10, and 0.12Lm(-3), resulting in mean coverage values of approximately 30%. The ANOVA of the field trial results showed that the 0.12Lm(-3) was the optimal specific spray volume for isolated olive trees. This specific spray volume gave the highest mean deposits, the best efficiency (as measured by the greatest normalized deposit), the most favourable penetration and homogeneity, and the highest coverage values.

  9. Sampling-based motion planning with reachable volumes: Theoretical foundations

    KAUST Repository

    McMahon, Troy

    2014-05-01

    © 2014 IEEE. We introduce a new concept, reachable volumes, that denotes the set of points that the end effector of a chain or linkage can reach. We show that the reachable volume of a chain is equivalent to the Minkowski sum of the reachable volumes of its links, and give an efficient method for computing reachable volumes. We present a method for generating configurations using reachable volumes that is applicable to various types of robots including open and closed chain robots, tree-like robots, and complex robots including both loops and branches. We also describe how to apply constraints (both on end effectors and internal joints) using reachable volumes. Unlike previous methods, reachable volumes work for spherical and prismatic joints as well as planar joints. Visualizations of reachable volumes can allow an operator to see what positions the robot can reach and can guide robot design. We present visualizations of reachable volumes for representative robots including closed chains and graspers as well as for examples with joint and end effector constraints.

  10. Finite Volume Methods: Foundation and Analysis

    Science.gov (United States)

    Barth, Timothy; Ohlberger, Mario

    2003-01-01

    Finite volume methods are a class of discretization schemes that have proven highly successful in approximating the solution of a wide variety of conservation law systems. They are extensively used in fluid mechanics, porous media flow, meteorology, electromagnetics, models of biological processes, semi-conductor device simulation and many other engineering areas governed by conservative systems that can be written in integral control volume form. This article reviews elements of the foundation and analysis of modern finite volume methods. The primary advantages of these methods are numerical robustness through the obtention of discrete maximum (minimum) principles, applicability on very general unstructured meshes, and the intrinsic local conservation properties of the resulting schemes. Throughout this article, specific attention is given to scalar nonlinear hyperbolic conservation laws and the development of high order accurate schemes for discretizing them. A key tool in the design and analysis of finite volume schemes suitable for non-oscillatory discontinuity capturing is discrete maximum principle analysis. A number of building blocks used in the development of numerical schemes possessing local discrete maximum principles are reviewed in one and several space dimensions, e.g. monotone fluxes, E-fluxes, TVD discretization, non-oscillatory reconstruction, slope limiters, positive coefficient schemes, etc. When available, theoretical results concerning a priori and a posteriori error estimates are given. Further advanced topics are then considered such as high order time integration, discretization of diffusion terms and the extension to systems of nonlinear conservation laws.

  11. Information architecture. Volume 4: Vision

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The Vision document marks the transition from definition to implementation of the Department of Energy (DOE) Information Architecture Program. A description of the possibilities for the future, supported by actual experience with a process model and tool set, points toward implementation options. The directions for future information technology investments are discussed. Practical examples of how technology answers the business and information needs of the organization through coordinated and meshed data, applications, and technology architectures are related. This document is the fourth and final volume in the planned series for defining and exhibiting the DOE information architecture. The targeted scope of this document includes DOE Program Offices, field sites, contractor-operated facilities, and laboratories. This document paints a picture of how, over the next 7 years, technology may be implemented, dramatically improving the ways business is conducted at DOE. While technology is mentioned throughout this document, the vision is not about technology. The vision concerns the transition afforded by technology and the process steps to be completed to ensure alignment with business needs. This goal can be met if those directing the changing business and mission-support processes understand the capabilities afforded by architectural processes.

  12. Resource Conservation and Recovery Act, Part B Permit Application [for the Waste Isolation Pilot Plant (WIPP)]. Volume 2, Chapter C, Appendix C1--Chapter C, Appendix C3 (beginning), Revision 3

    Energy Technology Data Exchange (ETDEWEB)

    1993-03-01

    This volume contains appendices for the following: Rocky Flats Plant and Idaho National Engineering Laboratory waste process information; TRUPACT-II content codes (TRUCON); TRUPACT-II chemical list; chemical compatibility analysis for Rocky Flats Plant waste forms; chemical compatibility analysis for waste forms across all sites; TRU mixed waste characterization database; hazardous constituents of Rocky Flats Transuranic waste; summary of waste components in TRU waste sampling program at INEL; TRU waste sampling program; and waste analysis data.

  13. iPhone 4s Photoplethysmography: Which Light Color Yields the Most Accurate Heart Rate and Normalized Pulse Volume Using the iPhysioMeter Application in the Presence of Motion Artifact?

    OpenAIRE

    Matsumura, Kenta; Rolfe, Peter; Lee, Jihyoung; Yamakoshi, Takehiro

    2014-01-01

    Recent progress in information and communication technologies has made it possible to measure heart rate (HR) and normalized pulse volume (NPV), which are important physiological indices, using only a smartphone. This has been achieved with reflection mode photoplethysmography (PPG), by using a smartphone’s embedded flash as a light source and the camera as a light sensor. Despite its widespread use, the method of PPG is susceptible to motion artifacts as physical displacements influence phot...

  14. Application of fracturing technology with fiber composite sand consolidation for increasing water volume of injection wells%注水井固砂增注压裂技术应用研究

    Institute of Scientific and Technical Information of China (English)

    彭中; 李升芳; 金智荣

    2013-01-01

    注水压力高,注水量达不到开发配注要求是各大油田存在的普遍问题。阐述了注水井压裂的必要性和纤维复合固砂压裂机理。通过建立数学模型,对注水井施工参数(裂缝长度、砂量)进行优化,得到适合注水井的压裂规模;优选了纤维浓度,对固结剂进行了性能评价。研究成果对提高注水井注入量,降低注水压力提供了重要指导。%There are generally high injection pressure and lower than designed water volume of injection wells in major oilfields.This paper expounds the necessity of fracturing for injection wells and mechanisms of fracturing with fiber compos-ite sand consolidation.By establishing the mathematical model,operation parameters of fracturing,including length and sand volume,were optimized to obtain an appropriate fracturing scale for injection wells.The fiber concentration was opti-mized and the performance of consolidation agent was evaluated.The research results can provide important guides for im-proving water volume and decreasing injection pressure of injection wells.

  15. Heliophysics 3 Volume Set

    Science.gov (United States)

    Schrijver, Carolus J.; Siscoe, George L.

    2010-11-01

    Volume 1: Preface; 1. Prologue Carolus J. Schrijver and George L. Siscoe; 2. Introduction to heliophysics Thomas J. Bogdan; 3. Creation and destruction of magnetic field Matthias Rempel; 4. Magnetic field topology Dana W. Longcope; 5. Magnetic reconnection Terry G. Forbes; 6. Structures of the magnetic field Mark B. Moldwin, George L. Siscoe and Carolus J. Schrijver; 7. Turbulence in space plasmas Charles W. Smith; 8. The solar atmosphere Viggo H. Hansteen; 9. Stellar winds and magnetic fields Viggo H. Hansteen; 10. Fundamentals of planetary magnetospheres Vytenis M. Vasyliūnas; 11. Solar-wind magnetosphere coupling: an MHD perspective Frank R. Toffoletto and George L. Siscoe; 12. On the ionosphere and chromosphere Tim Fuller-Rowell and Carolus J. Schrijver; 13. Comparative planetary environments Frances Bagenal; Bibliography; Index. Volume 2: Preface; 1. Perspective on heliophysics George L. Siscoe and Carolus J. Schrijver; 2. Introduction to space storms and radiation Sten Odenwald; 3. In-situ detection of energetic particles George Gloeckler; 4. Radiative signatures of energetic particles Tim Bastian; 5. Observations of solar and stellar eruptions, flares, and jets Hugh Hudson; 6. Models of coronal mass ejections and flares Terry Forbes; 7. Shocks in heliophysics Merav Opher; 8. Particle acceleration in shocks Dietmar Krauss-Varban; 9. Energetic particle transport Joe Giacalone; 10. Energy conversion in planetary magnetospheres Vytenis Vasyliūnas; 11. Energization of trapped particles Janet Green; 12. Flares, CMEs, and atmospheric responses Tim Fuller-Rowell and Stanley C. Solomon; 13. Energetic particles and manned spaceflight 358 Stephen Guetersloh and Neal Zapp; 14. Energetic particles and technology Alan Tribble; Appendix I. Authors and editors; List of illustrations; List of tables; Bibliography; Index. Volume 3: Preface; 1. Interconnectedness in heliophysics Carolus J. Schrijver and George L. Siscoe; 2. Long-term evolution of magnetic activity of Sun

  16. Application of cone beam CT in evaluating the bone defect volume in alveolar cleft%锥形束CT在评估牙槽突裂骨缺损体积中的应用

    Institute of Scientific and Technical Information of China (English)

    何锦泉; 欧阳可雄; 王朝俭; 张君伟; 黄珞; 王伟奇; 陈伦秋; 朴正国

    2016-01-01

    Objective To evaluate the accuracy of cone beam CT ( CBCT) in calculating the volume of the bone de-fect in alveolar cleft. Methods 14 patients with unilateral alveolar cleft were included in this study. Their image data were collected by CBCT scan and imported in the Mimics 10. 01 software. The volume of the bone defect in alveolar cleft was calculated by Mimics 10. 01 software. The real bone volumes transplanted during operation were measured by sterile syringes and were compared with preoperative CBCT data. Results The volume of bone defect from CBCT calculation was ( 2. 78 ± 0. 70) mL, while the real volume obtained in operation was ( 2. 88 ± 0. 70) mL. There was no significant difference between the CBCT data and the real bone defect ( P>0. 05) . The accuracy of CBCT in predicting bone defect volume was ( 95. 09 ± 2. 56)%. Conclusion The combination of CBCT data and Mimics software can evaluate the bone defect volume in alveolar cleft accurately.%目的:研究锥形束CT( cone beam CT,CBCT)在牙槽突裂植骨修复术前预测植骨量的准确性。方法选择14例单侧牙槽突裂患者为研究对象,术前通过CBCT扫描获取患者上颌骨影像数据并导入Mimics软件,用该软件测量牙槽突裂骨缺损体积。在术中通过5 mL注射器测量植入牙槽突裂隙中的松质骨骨量,获得牙槽突裂骨缺损的实际体积,并与术前测量结果进行对比分析。结果14例患者接受了牙槽突裂植骨术,手术均顺利完成,术前用CBCT和Mimics软件测量得到的牙槽突裂骨缺损体积为(2.78±0.70) mL,术中实际测量得到的牙槽突裂骨缺损体积为(2.88±0.70) mL,差异无统计学意义(P>0.05),术前CBCT预测牙槽突裂骨缺损体积准确率为(95.09±2.56)%。结论术前CBCT结合Mimics软件可精确计算牙槽突裂骨缺损体积。

  17. Finite volume schemes for dispersive wave propagation and runup

    OpenAIRE

    Dutykh, Denys; Katsaounis, Theodoros; Mitsotakis, Dimitrios

    2010-01-01

    Finite volume schemes are commonly used to construct approximate solutions to conservation laws. In this study we extend the framework of the finite volume methods to dispersive water wave models, in particular to Boussinesq type systems. We focus mainly on the application of the method to bidirectional nonlinear, dispersive wave propagation in one space dimension. Special emphasis is given to important nonlinear phenomena such as solitary waves interactions, dispersive shock wave formation a...

  18. Computing the partial volume of pressure vessels

    Energy Technology Data Exchange (ETDEWEB)

    Wiencke, Bent [Nestle USA, Corporate Engineering, 800 N. Brand Blvd, Glendale, CA 91203 (United States)

    2010-06-15

    The computation of the partial and total volume of pressure vessels with various type of head profiles requires detailed knowledge of the head profile geometry. Depending on the type of head profile the derivation of the equations can become very complex and the calculation process cumbersome. Certain head profiles require numerical methods to obtain the partial volume, which for most application is beyond the scope of practicability. This paper suggests a unique method that simplifies the calculation procedure for the various types of head profiles by using one common set of equations without the need for numerical or complex computation methods. For ease of use, all equations presented in this paper are summarized in a single table format for horizontal and vertical vessels. (author)

  19. Topology optimization using the finite volume method

    DEFF Research Database (Denmark)

    Gersborg-Hansen, Allan; Bendsøe, Martin P.; Sigmund, Ole

    Computational procedures for topology optimization of continuum problems using a material distribution method are typically based on the application of the finite element method (FEM) (see, e.g. [1]). In the present work we study a computational framework based on the finite volume method (FVM, see...... the arithmetic and harmonic average with the latter being the well known Reuss lower bound. [1] Bendsøe, MP and Sigmund, O 2004: Topology Optimization - Theory, Methods, and Applications. Berlin Heidelberg: Springer Verlag [2] Versteeg, HK and Malalasekera, W 1995: An introduction to Computational Fluid Dynamics......, e.g. [2]) in order to develop methods for topology design for applications where conservation laws are critical such that element--wise conservation in the discretized models has a high priority. This encompasses problems involving for example mass and heat transport. The work described...

  20. Volume and Surface-Enhanced Volume Negative Ion Sources

    CERN Document Server

    Stockli, M P

    2013-01-01

    H- volume sources and, especially, caesiated H- volume sources are important ion sources for generating high-intensity proton beams, which then in turn generate large quantities of other particles. This chapter discusses the physics and technology of the volume production and the caesium-enhanced (surface) production of H- ions. Starting with Bacal's discovery of the H- volume production, the chapter briefly recounts the development of some H- sources, which capitalized on this process to significantly increase the production of H- beams. Another significant increase was achieved in the 1990s by adding caesiated surfaces to supplement the volume-produced ions with surface-produced ions, as illustrated with other H- sources. Finally, the focus turns to some of the experience gained when such a source was successfully ramped up in H- output and in duty factor to support the generation of 1 MW proton beams for the Spallation Neutron Source.

  1. Profiling of micrometer-sized laser beams in restricted volumes

    DEFF Research Database (Denmark)

    Miroshnychenko, Yevhen; Nielsen, Otto; Thorsen, Aske;

    2012-01-01

    micrometers across the measuring volume. We characterize the performance of the method and experimentally demonstrate profiling of micrometer-sized laser beams. We discuss the limiting factors and routes toward a further increase of the resolution and beam profiling in even more restricted volumes. Finally......, as an application example, we present profiling of laser beams inside a micro ion trap with integrated optical fibers.......We present a method for determining the three-dimensional intensity distribution of directed laser radiation with micrometer resolution in restricted volumes. Our method is based on the incoupling and guiding properties of optical fibers, with the current version requiring only a few hundred...

  2. Shaping 3-D Volumes in Immersive Virtual Environments

    DEFF Research Database (Denmark)

    Stenholt, Rasmus

    within the area of volume shaping. As such, each paper builds on the results of its predecessors. The first paper deals specifically with the task of shaping a 3-D box. Boxes are arguably one of the most commonly used 3-D shapes, both in real life and in virtual worlds. Therefore, the problem......Shaping 3-D volumes is an important part of many interactions in immersive virtual environments. The range of possible applications is wide. For instance, the ability to select objects in virtual environments is very often based on defin- ing and controlling a selection volume. This is especially...

  3. Diarylethene Materials for Rewritable Volume Holographic Data Storage

    Institute of Scientific and Technical Information of China (English)

    刘国栋; 何庆声; 丁德华; 邬敏贤; 金国藩; 蒲守智; 张复实; 刘学东; 袁鹏

    2003-01-01

    The photochromic diarylethene, 1,2-bis(2-methyl-5-(4-formyIphenyl)-thien-3-yl)perfluorocyclopentene ( 1 a) is studied and its applicable potential in rewritable volume holographic data storage is verified. Holographic recording films of 10-μm thickness have been fabricated. The refractive index modulation (△n = 1.15 × 10-3) between the open- and close-ring forms is detected to be large enough so that the films are suitable for the production of volume holographic storage. The experiments of angle multiplexing and rewriting holograms show that the materials are fit for volume holographic data storage.

  4. Facilitating cartilage volume measurement using MRI

    Energy Technology Data Exchange (ETDEWEB)

    Maataoui, Adel, E-mail: adel.maataoui@gmx.d [Institute for Diagnostic and Interventional Radiology, Johann Wolfgang Goethe University, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany); Gurung, Jessen, E-mail: jessen.gurung@gmx.d [Institute for Diagnostic and Interventional Radiology, Johann Wolfgang Goethe University, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany); Ackermann, Hanns, E-mail: h.ackermann@add.uni-frankfurt.d [Institute for Epidemiology and Medical Statistics, Johann Wolfgang Goethe University, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany); Abolmaali, Nasreddin [Biological and Molecular Imaging, ZIK OncoRay - Radiation Research in Oncology, Medical Faculty Carl Gustav Carus, TU Dresden, Fetscherstrasse 74, 01307 Dresden (Germany); Kafchitsas, Konstantinos [Department of Orthopedics and Orthopedic Surgery, Johannes Gutenberg University, Langenbeckstrasse 1, 55131 Mainz (Germany); Vogl, Thomas J., E-mail: t.vogl@em.uni-frankfurt.d [Institute for Diagnostic and Interventional Radiology, Johann Wolfgang Goethe University, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany); Khan, M. Fawad, E-mail: fawad@gmx.d [Institute for Diagnostic and Interventional Radiology, Johann Wolfgang Goethe University, Theodor-Stern-Kai 7, 60590 Frankfurt am Main (Germany)

    2010-08-15

    Purpose: To compare quantitative cartilage volume measurement (CVM) using different slice thicknesses. Materials and methods: Ten knees were scanned with a 1.5 T MRI (Sonata, Siemens, Erlangen, Germany) using a 3D gradient echo sequence (FLASH, fast low-angle shot). Cartilage volume of the medial and lateral tibial plateau was measured by two independent readers in 1.5 mm, 3.0 mm and 5.0 mm slices using the Argus software application. Accuracy and time effectiveness served as control parameters. Results: Determining cartilage volume, time for calculation diminished for the lateral tibial plateau from 384.6 {+-} 127.7 s and 379.1 {+-} 117.6 s to 214.9 {+-} 109.9 s and 213.9 {+-} 102.2 s to 122.1 {+-} 60.1 s and 126.8 {+-} 56.2 s and for the medial tibial plateau from 465.0 {+-} 147.7 s and 461.8 {+-} 142.7 s to 214.0 {+-} 67.9 s and 208.9 {+-} 66.2 s to 132.6 {+-} 41.5 s and 130.6 {+-} 42.0 s measuring 1.5 mm, 3 mm and 5 mm slices, respectively. No statistically significant difference between cartilage volume measurements was observed (p > 0.05) while very good inter-reader correlation was evaluated. Conclusion: CVM using 1.5 mm slices provides no higher accuracy than cartilage volume measurement in 5 mm slices while an overall time saving up to 70% is possible.

  5. Absorbed fractions for electrons in ellipsoidal volumes

    Science.gov (United States)

    Amato, E.; Lizio, D.; Baldari, S.

    2011-01-01

    We applied a Monte Carlo simulation in Geant4 in order to calculate the absorbed fractions for monoenergetic electrons in the energy interval between 10 keV and 2 MeV, uniformly distributed in ellipsoids made from soft tissue. For each volume, we simulated a spherical shape, four oblate and four prolate ellipsoids, and one scalene shape. For each energy and for every geometrical configuration, an analytical relationship between the absorbed fraction and a 'generalized radius' was found, and the dependence of the fit parameters from electron energy is discussed and fitted by proper parametric functions. With the proposed formulation, the absorbed fraction for electrons in the 10-2000 keV energy range can be calculated for all volumes and for every ellipsoidal shape of practical interest. This method can be directly applied to evaluation of the absorbed fraction from the radionuclide emission of monoenergetic electrons, such as Auger or conversion electrons. The average deposited energy per disintegration in the case of extended beta spectra can be evaluated through integration. Two examples of application to a pure beta emitter such as 90Y and to 131I, whose emission include monoenergetic and beta electrons plus gamma photons, are presented. This approach represent a generalization of our previous studies, allowing a comprehensive treatment of absorbed fractions from electron and photon sources uniformly distributed in ellipsoidal volumes of any ellipticity and volume, in the whole range of practical interest for internal dosimetry in nuclear medicine applications, as well as in radiological protection estimations of doses from an internal contamination.

  6. An Example Emphasizing Mass-Volume Relationships for Problem Solving in Soils

    Science.gov (United States)

    Heitman, J. L.; Vepraskas, M. J.

    2009-01-01

    Mass-volume relationships are a useful tool emphasized for problem solving in many geo-science and engineering applications. These relationships also have useful applications in soil science. Developing soils students' ability to utilize mass-volume relationships through schematic diagrams of soil phases (i.e., air, water, and solid) can help to…

  7. Regulatory and necrotic volume increase in boar spermatozoa.

    Science.gov (United States)

    Petrunkina, A M; Jebe, E; Töpfer-Petersen, E

    2005-08-01

    subsequent volume decrease. RVI was inhibited by the vanadate. Hypertonic stress did not result in an increase in early apoptotic cells, but produced a shift toward late necrotic cells. Substitution of sodium and chloride by choline and sulfate resulted in decreased isotonic volume of sperm treated with lavendustin. Tyrosine phosphorylation levels were reduced after 20 min under hypertonic conditions. It was concluded that RVI is regulated via a protein tyrosine kinase-dependent pathway, and that dephosphorylation occurs when volume regulation is required. The necrotic volume increase (NVI) is associated with the accumulation of sodium and chloride following uncontrolled opening of the channels. The ability to regulate volume after exposure to hypertonic conditions is important for sperm functionality and can have practical applications in spermatological diagnostics and cryopreservation. PMID:15744775

  8. Research progress and clinical application value of pericardial adipose volume%心包脂肪体积的研究进展及临床应用价值

    Institute of Scientific and Technical Information of China (English)

    李江

    2013-01-01

    Pericardial adipose tissue,a special anatomical distribution of complex physiological and biochemical characteristics,as well as its relation to coronary atherosclerosis,has become a global hotspot.Increasing of the PAT volume has been recognized as an important risk factor for atherosclerotic disease and metabolic syndrome.PAT volume is closely related to the development of coronary atherosclerosis,identification and evaluation of visceral adipose tissue is critical.So the risk prediction and diagnosis of coronary atherosclerotic heart disease by PAT volume have high clinical value,which may be a therapeutic target for coronary heart disease.%心包脂肪组织(pericardial adipose tissue,PAT)特殊的解剖学分布、复杂的生理生化特性以及与冠状动脉粥样硬化的密切相关性使其成为世界性研究热点.PAT体积增加已被公认是动脉粥样硬化性疾病和代谢综合征的一个重要危险因素.PAT体积与冠状动脉粥样硬化的发生发展密切相关,对内脏脂肪组织的鉴别和评价至关重要,故PAT体积对冠状动脉粥样硬化性心脏病的风险预测及诊断具有极高的临床应用价值,并可能成为冠心病的治疗靶点.

  9. Resource Conservation and Recovery Act, Part B permit application [of the Waste Isolation Pilot Plant (WIPP)]. Volume 11, Chapter D, Appendix D4--Chapter D, Appendix D17: Revision 3

    Energy Technology Data Exchange (ETDEWEB)

    1993-03-01

    This volume contains appendices D4 through D17 which cover the following: Waste Isolation Pilot Plant site environmental report; ecological monitoring program at the Waste Isolation Pilot Plant; site characterization; regional and site geology and hydrology; general geology; dissolution features; ground water hydrology; typical carbon sorption bed efficiency; VOC monitoring plan for bin-room tests; chemical compatibility analysis of waste forms and container materials; probable maximum precipitation; WHIP supplementary roof support system room 1, panel 1; and corrosion risk assessment of the Waste Isolation Pilot Plant ``humid`` test bins.

  10. Finding related functional neuroimaging volumes

    DEFF Research Database (Denmark)

    Nielsen, Finn Årup; Hansen, Lars Kai

    2004-01-01

    We describe a content-based image retrieval technique for finding related functional neuroimaging experiments by voxelization of sets of stereotactic coordinates in Talairach space, comparing the volumes and reporting related volumes in a sorted list. Voxelization is accomplished by convolving each...

  11. Radiobioassays. Volume 2

    Energy Technology Data Exchange (ETDEWEB)

    Ashkar, F.S.

    1983-01-01

    This book presents papers on radioimmunoassay. Topics considered include the clinical application of the radioimmunoassay of insulin, the renin-angiotensin system, growth hormone radioimmunoassay, estrogen and progesterone receptor techniques for breast cancer, radioassay in hematology, serum bile acids, the role of gastrin in normal physiology and disease states, tumor markers in the immunodiagnosis of cancer, assays of drugs by immunological methods, radioassay in allergy and immunology, radioimmunoassay in cardiovascular disease, and radioimmunoassay in cardiovascular disease, and radioimmunoassays for the diagnosis of infectious diseases.

  12. Natural Computing in Computational Finance Volume 4

    CERN Document Server

    O’Neill, Michael; Maringer, Dietmar

    2012-01-01

    This book follows on from Natural Computing in Computational Finance  Volumes I, II and III.   As in the previous volumes of this series, the  book consists of a series of  chapters each of  which was selected following a rigorous, peer-reviewed, selection process.  The chapters illustrate the application of a range of cutting-edge natural  computing and agent-based methodologies in computational finance and economics.  The applications explored include  option model calibration, financial trend reversal detection, enhanced indexation, algorithmic trading,  corporate payout determination and agent-based modeling of liquidity costs, and trade strategy adaptation.  While describing cutting edge applications, the chapters are  written so that they are accessible to a wide audience. Hence, they should be of interest  to academics, students and practitioners in the fields of computational finance and  economics.  

  13. Sparse PDF Volumes for Consistent Multi-Resolution Volume Rendering

    KAUST Repository

    Sicat, Ronell

    2014-12-31

    This paper presents a new multi-resolution volume representation called sparse pdf volumes, which enables consistent multi-resolution volume rendering based on probability density functions (pdfs) of voxel neighborhoods. These pdfs are defined in the 4D domain jointly comprising the 3D volume and its 1D intensity range. Crucially, the computation of sparse pdf volumes exploits data coherence in 4D, resulting in a sparse representation with surprisingly low storage requirements. At run time, we dynamically apply transfer functions to the pdfs using simple and fast convolutions. Whereas standard low-pass filtering and down-sampling incur visible differences between resolution levels, the use of pdfs facilitates consistent results independent of the resolution level used. We describe the efficient out-of-core computation of large-scale sparse pdf volumes, using a novel iterative simplification procedure of a mixture of 4D Gaussians. Finally, our data structure is optimized to facilitate interactive multi-resolution volume rendering on GPUs.

  14. Fluoride Induces a Volume Reduction in CA1 Hippocampal Slices Via MAP Kinase Pathway Through Volume Regulated Anion Channels.

    Science.gov (United States)

    Lee, Jaekwang; Han, Young-Eun; Favorov, Oleg; Tommerdahl, Mark; Whitsel, Barry; Lee, C Justin

    2016-04-01

    Regulation of cell volume is an important aspect of cellular homeostasis during neural activity. This volume regulation is thought to be mediated by activation of specific transporters, aquaporin, and volume regulated anion channels (VRAC). In cultured astrocytes, it was reported that swelling-induced mitogen-activated protein (MAP) kinase activation is required to open VRAC, which are thought to be important in regulatory volume decrease and in the response of CNS to trauma and excitotoxicity. It has been also described that sodium fluoride (NaF), a recognized G-protein activator and protein phosphatase inhibitor, leads to a significant MAP kinase activation in endothelial cells. However, NaF's effect in volume regulation in the brain is not known yet. Here, we investigated the mechanism of NaF-induced volume change in rat and mouse hippocampal slices using intrinsic optical signal (IOS) recording, in which we measured relative changes in intracellular and extracellular volume as changes in light transmittance through brain slices. We found that NaF (1~5 mM) application induced a reduction in light transmittance (decreased volume) in CA1 hippocampus, which was completely reversed by MAP kinase inhibitor U0126 (10 µM). We also observed that NaF-induced volume reduction was blocked by anion channel blockers, suggesting that NaF-induced volume reduction could be mediated by VRAC. Overall, our results propose a novel molecular mechanism of NaF-induced volume reduction via MAP kinase signaling pathway by activation of VRAC. PMID:27122993

  15. Fluoride Induces a Volume Reduction in CA1 Hippocampal Slices Via MAP Kinase Pathway Through Volume Regulated Anion Channels

    Science.gov (United States)

    Lee, Jaekwang; Han, Young-Eun; Favorov, Oleg; Tommerdahl, Mark; Whitsel, Barry

    2016-01-01

    Regulation of cell volume is an important aspect of cellular homeostasis during neural activity. This volume regulation is thought to be mediated by activation of specific transporters, aquaporin, and volume regulated anion channels (VRAC). In cultured astrocytes, it was reported that swelling-induced mitogen-activated protein (MAP) kinase activation is required to open VRAC, which are thought to be important in regulatory volume decrease and in the response of CNS to trauma and excitotoxicity. It has been also described that sodium fluoride (NaF), a recognized G-protein activator and protein phosphatase inhibitor, leads to a significant MAP kinase activation in endothelial cells. However, NaF's effect in volume regulation in the brain is not known yet. Here, we investigated the mechanism of NaF-induced volume change in rat and mouse hippocampal slices using intrinsic optical signal (IOS) recording, in which we measured relative changes in intracellular and extracellular volume as changes in light transmittance through brain slices. We found that NaF (1~5 mM) application induced a reduction in light transmittance (decreased volume) in CA1 hippocampus, which was completely reversed by MAP kinase inhibitor U0126 (10 µM). We also observed that NaF-induced volume reduction was blocked by anion channel blockers, suggesting that NaF-induced volume reduction could be mediated by VRAC. Overall, our results propose a novel molecular mechanism of NaF-induced volume reduction via MAP kinase signaling pathway by activation of VRAC. PMID:27122993

  16. Irradiation of target volumes with concave outlines

    Energy Technology Data Exchange (ETDEWEB)

    De Neve, W.; Fortan, L.; Derycke, S.; Van Duyse, B.; DE Wagter, C. [Ghent Rijksuniversiteit (Belgium). Kliniek voor Radiotherapie en Kerngeneeskunde

    1995-12-01

    A heuristic planning procedure allowing to obtain a 3-dimensional conformal dose distribution for target volumes with concavities has been investigated. The procedure divides the planning problem into a number of sub-problems each solvable by known methods. By patching together the solutions to the sub-problems, a solution with a predictable dosimetric outcome can be obtained. The procedure can be applied to most 3-dimensional systems. The procedure is described and its applications to the irradiation of neoplasms are discussed. (A.S.).

  17. COMPARISON BETWEEN MULTICOPTER UAV AND TOTAL STATION FOR ESTIMATING STOCKPILE VOLUMES

    Directory of Open Access Journals (Sweden)

    C. Arango

    2015-08-01

    Full Text Available Currently the UAV (Unmanned Aerial Vehicle have become an alternative for different engineering applications, especially in surveying, one of these applications is the calculation of volumes of stockpiled material, but there are questions about its accuracy and efficiency, the purpose of this article is to compare traditional surveying methods for estimating total volumes through data obtained by total stations and data obtained by a multicopter UAV. In order to answer these questions we obtain data from the same location and the results were compared. After comparing the results it was found that there was a 2,88% difference between the volume calculated with the total station data and the actual volume, and −0,67% difference between the volume calculated with the UAV data and the actual volume, concluding that the estimated volume with UAV data is more accurate.

  18. Liquid-solid flows 1994. FED Volume 189

    International Nuclear Information System (INIS)

    The collection of papers from this volume illustrate the current research trends in the fundamental aspects of two-phase flow, development of instrumentation with good temporal and spatial resolution, two-phase flow in rotating machinery, and numerical simulation of particulate flows using local analytical solutions and parallel processing. The application oriented papers deal with slurry pipes and pumps, mixing, fluidization and porous media. The volume was organized into four topic areas: modeling; experiments; numerical simulations; and pumping equipment and applications. Papers have been processed separately for inclusion the data base

  19. Minivoids in the Local Volume

    CERN Document Server

    Tikhonov, A V

    2006-01-01

    We consider a sphere of 7.5 Mpc radius, which contains 355 galaxies with accurately measured distances, to detect the nearest empty volumes. Using a simple void detection algorithm, we found six large (mini)voids in Aquila, Eridanus, Leo, Vela, Cepheus and Octans, each of more than 30 Mpc^3. Besides them, 24 middle-size "bubbles" of more than 5 Mpc^3 volume are detected, as well as 52 small "pores". The six largest minivoids occupy 58% of the considered volume. Addition of the bubbles and pores to them increases the total empty volume up to 75% and 81%, respectively. The detected local voids look like oblong potatoes with typical axial ratios b/a = 0.75 and c/a = 0.62 (in the triaxial ellipsoide approximation). Being arranged by the size of their volume, local voids follow power law of volumes-rankes dependence. A correlation Gamma-function of the Local Volume galaxies follows a power low with a formally calculated fractal dimension D = 1.5. We found that galaxies surrounding the local minivoids do not differ...

  20. An Improved Velocity Volume Processing Method

    Institute of Scientific and Technical Information of China (English)

    LI Nan; WEI Ming; TANG Xiaowen; PAN Yujie

    2007-01-01

    Velocity volume processing (VVP) retrieval of single Doppler radar is an effective method which can be used to obtain many wind parameters. However, due to the problem of an ill-conditioned matrix arising from the coefficients of equations not being easily resolved, the VVP method has not been applied adequately and effectively in operation. In this paper, an improved scheme, SVVP (step velocity volume processing), based on the original method, is proposed. The improved algorithm retrieves each group of components of the wind field through a stepwise procedure, which overcomes the problem of an ill-conditioned matrix, which currently limits the application of the VVP method. Variables in a six-parameter model can be retrieved even if the analysis volume is very small. In addition, the source and order of errors which exist in the traditional method are analyzed. The improved method is applied to real cases, which show that it is robust and has the capability to obtain the wind field structure of the local convective system. It is very helpful for studying severe storms.

  1. Plasma volume changes during hypoglycaemia

    DEFF Research Database (Denmark)

    Hilsted, J; Bendtsen, F; Christensen, N J;

    1990-01-01

    To investigate whether previously reported changes in venous blood volume and composition induced by acute hypoglycaemia in humans are representative for the entire body we measured erythrocyte 51Cr content, haematocrit, plasma volume, intravascular albumin content and transcapillary escape rate...... of albumin in arterial and venous blood in seven healthy subjects before and during insulin-induced hypoglycaemia. In both vascular sites blood 51Cr content and the haematocrit increased, plasma volume and intravascular albumin content decreased and the transcapillary escape rate of albumin increased during...

  2. Plasma volume changes during hypoglycaemia

    DEFF Research Database (Denmark)

    Hilsted, J; Frandsen, Henrik Lund; Christensen, N J;

    1991-01-01

    -induced hypoglycaemia with total autonomic blockade (alpha-adrenoceptor blockade combined with beta-adrenoceptor blockade and atropine); and insulin-induced hypoglycaemia without any autonomic blockade. In the experiments without autonomic blockade the peripheral venous hematocrit increased, plasma volume decreased......, intravascular albumin content decreased and the transcapillary escape rate of albumin increased. In both experiments with autonomic blockade the increase in venous haematocrit was abolished, yet plasma volume decreased, intravascular albumin content decreased and the transcapillary escape rate of albumin...... increased in these experiments. Thus, the changes in plasma volume and composition in response to hypoglycaemia are due to the combined actions of adrenaline and of insulin....

  3. Cell swelling and volume regulation

    DEFF Research Database (Denmark)

    Hoffmann, Else Kay

    1992-01-01

    The extracellular space in the brain is typically 20% of the tissue volume and is reduced to at least half its size under conditions of neural insult. Whether there is a minimum size to the extracellular space was discussed. A general model for cell volume regulation was presented, followed...... by a discussion on how many of the generally involved mechanisms are identified in neural cells and (or) in astrocytes. There seems to be clear evidence suggesting that parallel K+ and Cl- channels mediate regulatory volume decrease in primary cultures of astrocytes, and a stretch-activated cation channel has...

  4. Dictionary Based Segmentation in Volumes

    DEFF Research Database (Denmark)

    Emerson, Monica Jane; Jespersen, Kristine Munk; Jørgensen, Peter Stanley;

    2015-01-01

    We present a method for supervised volumetric segmentation based on a dictionary of small cubes composed of pairs of intensity and label cubes. Intensity cubes are small image volumes where each voxel contains an image intensity. Label cubes are volumes with voxelwise probabilities for a given...... label. The segmentation process is done by matching a cube from the volume, of the same size as the dictionary intensity cubes, to the most similar intensity dictionary cube, and from the associated label cube we get voxel-wise label probabilities. Probabilities from overlapping cubes are averaged and...

  5. Dictionary Based Segmentation in Volumes

    DEFF Research Database (Denmark)

    Emerson, Monica Jane; Jespersen, Kristine Munk; Jørgensen, Peter Stanley;

    2015-01-01

    We present a method for supervised volumetric segmentation based on a dictionary of small cubes composed of pairs of intensity and label cubes. Intensity cubes are small image volumes where each voxel contains an image intensity. Label cubes are volumes with voxelwise probabilities for a given...... label. The segmentation process is done by matching a cube from the volume, of the same size as the dictionary intensity cubes, to the most similar intensity dictionary cube, and from the associated label cube we get voxel-wise label probabilities. Probabilities from overlapping cubes are averaged...

  6. Particles in small volume injections.

    Science.gov (United States)

    Taylor, S A; Spence, J

    1983-12-01

    The level of particulate contamination in small volume injections has been examined using the light blockage (HIAC) and electrical sensing zone (Coulter counter) techniques, the HIAC system being found to be the more suitable. Particle counts on the same batch of injection showed a large and variable difference between the HIAC and the Coulter counter results, especially below 5 micron. None of the injections examined complied with the British Pharmacopoeia limits for particulates in large volume parenterals, suggesting the unsuitability of the limits for small volume parenterals. PMID:6141237

  7. Fiscal year 1985 Department of Energy authorization. Volume I. Hearing before the Subcommittee on Energy Research and Production and the Subcommittee on Energy Development and Applications, US House of Representatives, Ninety-Eighth Congress, Second Session, March 13, 1984

    Energy Technology Data Exchange (ETDEWEB)

    1984-01-01

    Volume I of the hearing record covers the March 13, 1984 testimony of Martha Hesse, Assistant DOE Secretary for Management and Administration, on the fiscal year 1985 budget request for DOE administration. Ms. Hesse discussed specific budget justifications, including funding for the Technical Information Services, in-house energy management, and policy initiatives, such as the realignment of some functions within the department, the introduction of an integrated accouting and personnel and payroll systems, and other efforts to reduce overhead costs. She reported a three percent drop in staffing level. Following a prepared statement by Ms. Hesse and introductory remarks by committee members, the bulk of the hearing record contains responses to committee questions.

  8. Analysis of concentrating PV-T systems for the commercial/industrial sector. Volume II. PV-T state-of-the-art survey and site/application pair selection and analysis

    Energy Technology Data Exchange (ETDEWEB)

    Schwinkendorf, W.E.

    1984-09-01

    As part of a project to develop feasibility assessments, design procedures, and reference designs for total energy systems that could use actively cooled concentrating photovoltaic collectors, a survey was conducted to provide an overview of available photovoltaic-thermal (PV-T) technology. General issues associated with the design and installation of a PV-T system are identified. Electrical and thermal efficiencies for the line-focus Fresnel, the linear parabolic trough, and the point-focus Fresnel collectors are specified as a function of operating temperature, ambient temperature, and insolation. For current PV-T technologies, the line-focus Fresnel collector proved to have the highest thermal and electrical efficiencies, lowest array cost, and lowest land area requirement. But a separate feasibility analysis involving 11 site/application pairs showed that for most applications, the cost of the photovoltaic portion of a PV-T system is not recovered through the displacement of an electrical load, and use of a thermal-only system to displace the thermal load would be a more economical alternative. PV-T systems are not feasible for applications that have a small thermal load, a large steam requirement, or a high load return temperature. SAND82-7157/3 identifies the technical issues involved in designing a photovoltaic-thermal system and provides guidance for resolving such issues. Detailed PV-T system designs for three selected applications and the results of a trade-off study for these applications are presented in SAND82-7157/4. A summary of the major results of this entire study and conclusions concerning PV-T systems and applications is presented in SAND82-7157/1.

  9. 10 CFR 63.332 - Representative volume.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 2 2010-01-01 2010-01-01 false Representative volume. 63.332 Section 63.332 Energy... Protection Standards § 63.332 Representative volume. (a) The representative volume is the volume of ground... radionuclides released from the Yucca Mountain disposal system that will be in the representative volume....

  10. Fundamental Concepts in Biophysics Volume 1

    CERN Document Server

    Jue, Thomas

    2009-01-01

    HANDBOOK OF MODERN BIOPHYSICS Series Editor Thomas Jue, PhD Handbook of Modern Biophysics brings current biophysics topics into focus, so that biology, medical, engineering, mathematics, and physical-science students or researchers can learn fundamental concepts and the application of new techniques in addressing biomedical challenges. Chapters explicate the conceptual framework of the physics formalism and illustrate the biomedical applications. With the addition of problem sets, guides to further study, and references, the interested reader can continue to explore independently the ideas presented. Volume I: Fundamental Concepts in Biophysics Editor Thomas Jue, PhD In Fundamental Concepts in Biophysics, prominent professors have established a foundation for the study of biophysics related to the following topics: Mathematical Methods in Biophysics Quantum Mechanics Basic to Biophysical Methods Computational Modeling of Receptor–Ligand Binding and Cellular Signaling Processes Fluorescence Spectroscopy Elec...

  11. Organ volume estimation using SPECT

    CERN Document Server

    Zaidi, H

    1996-01-01

    Knowledge of in vivo thyroid volume has both diagnostic and therapeutic importance and could lead to a more precise quantification of absolute activity contained in the thyroid gland. In order to improve single-photon emission computed tomography (SPECT) quantitation, attenuation correction was performed according to Chang's algorithm. The dual-window method was used for scatter subtraction. We used a Monte Carlo simulation of the SPECT system to accurately determine the scatter multiplier factor k. Volume estimation using SPECT was performed by summing up the volume elements (voxels) lying within the contour of the object, determined by a fixed threshold and the gray level histogram (GLH) method. Thyroid phantom and patient studies were performed and the influence of 1) fixed thresholding, 2) automatic thresholding, 3) attenuation, 4) scatter, and 5) reconstruction filter were investigated. This study shows that accurate volume estimation of the thyroid gland is feasible when accurate corrections are perform...

  12. Human gallbladder pressure and volume

    DEFF Research Database (Denmark)

    Borly, L; Højgaard, L; Grønvall, S;

    1996-01-01

    influenced by respiration (n = 8) and the pressure seems to be higher in the sitting position than in the supine position (n = 5). Cystic duct opening pressure was 10.4, 11.2 and 16.8 mmHg (n = 3). Pressure-volume responses showed that the GB up to a certain volume could accommodate increases in intraluminal...... volume with only slight changes in intraluminal pressure (n = 4). Except for the zero drift, this piece of equipment seemed to fulfil the requirements of being able to measure pressure in the GB. In vivo measurements showed a good clinical reproducibility of the method, and also that respiration...... and patient posture influenced the pressure measurements. Further, a GB pressure-volume relationship was demonstrated, and the possibility of a cystic duct opening pressure was described....

  13. Optimization-based mesh correction with volume and convexity constraints

    Science.gov (United States)

    D'Elia, Marta; Ridzal, Denis; Peterson, Kara J.; Bochev, Pavel; Shashkov, Mikhail

    2016-05-01

    We consider the problem of finding a mesh such that 1) it is the closest, with respect to a suitable metric, to a given source mesh having the same connectivity, and 2) the volumes of its cells match a set of prescribed positive values that are not necessarily equal to the cell volumes in the source mesh. This volume correction problem arises in important simulation contexts, such as satisfying a discrete geometric conservation law and solving transport equations by incremental remapping or similar semi-Lagrangian transport schemes. In this paper we formulate volume correction as a constrained optimization problem in which the distance to the source mesh defines an optimization objective, while the prescribed cell volumes, mesh validity and/or cell convexity specify the constraints. We solve this problem numerically using a sequential quadratic programming (SQP) method whose performance scales with the mesh size. To achieve scalable performance we develop a specialized multigrid-based preconditioner for optimality systems that arise in the application of the SQP method to the volume correction problem. Numerical examples illustrate the importance of volume correction, and showcase the accuracy, robustness and scalability of our approach.

  14. Duration of increase in vascular volume during venous stasis

    DEFF Research Database (Denmark)

    Sejrsen, P; Henriksen, O; Paaske, W P;

    1981-01-01

    the rate of increase in calf volume declined to a steady level after about 5 min. Both the studies with 133Xenon and with 99mTc-erythrocytes indicate that vascular volume continued to increase for 3, 3.5 and 5 min following venous stasis of 20, 30 and 40 mmHg, respectively. When the crus was lowered 50 cm...... below heart level the duration of increase in vascular volume following an additional increase in venous pressure induced by venous stasis was shorter than in the horizontal position. When the calf is placed at heart level the results indicate that for up to 5 min after application of venous stasis...... of 40 mmHg both increase in vascular volume and transcapillary fluid filtration contribute to the observed increase in calf volume. Using the rate of increase in calf volume within 5 min after induction of venous stasis thus leads to overestimation of CFC. After 5 min vascular volume appears to remain...

  15. Volume de madeira e concentração foliar de nutrientes em parcelas experimentais de Eucalyptus grandis fertilizadas com lodos de esgoto úmido e seco Wood volume and foliar concentration of nutrients in Eucalyptus grandis after wet and dry sewage sludge application

    Directory of Open Access Journals (Sweden)

    Paulo Henrique Muller da Silva

    2008-10-01

    Full Text Available No Brasil, diversos municípios estão construindo estações de tratamento de esgoto (ETEs, e futuramente serão produzidas anualmente milhares de toneladas de lodo para as quais deverá ser dada destinação adequada. O lodo de esgoto tratado (biossólido é o resíduo resultante do tratamento do esgoto urbano, e sua disposição final precisa ser bem planejada devido às implicações sanitárias, ambientais, econômicas e sociais. Apresenta elevado teor de matéria orgânica e de nutrientes e poderia ser utilizado como fertilizante em plantios florestais. Esta pesquisa foi realizada na Estação de Ciências Florestais de Itatinga (Universidade de São Paulo, com o objetivo de avaliar o efeito da adição de três doses (10, 20 e 30 t ha-1 dos lodos de esgoto úmido (torta e seco (granulado, complementados com K e B e aplicados ao solo nas linhas de plantio em parcelas experimentais de Eucalyptus grandis. Dezoito meses após a implantação das mudas no campo, o volume dos troncos demonstrou aumento significativo (ao redor de 130% no tocante ao crescimento dos eucaliptos tratados com os biossólidos úmido e seco em relação à testemunha sem aplicação de fertilizante, bem como teve resultado semelhante ao do tratamento com adubo mineral. Entretanto, não houve diferença significativa entre os tratamentos com a aplicação dos biossólidos úmido e seco. Com relação à nutrição mineral, foi observado aumento da concentração dos elementos P, Ca e Zn nas folhas com as maiores doses dos biossólidos, e verificou-se efeito inverso de Mn. As concentrações foliares de todos os nutrientes nos eucaliptos tratados com os biossólidos mantiveram-se dentro dos limites observados usualmente nas plantações comerciais, não havendo sinais de desequilíbrio nutricional.In Brazil, several municipalities are building waste treatment plants and in the future thousands of tons of sewage sludge will be generated. Sewage sludge is the waste left

  16. SET OPERATOR-BASED METHOD OF DENOISING MEDICAL VOLUME DATA

    Institute of Scientific and Technical Information of China (English)

    程兵; 郑南宁; 袁泽剑

    2002-01-01

    Objective To investigate impulsive noise suppression of medical volume data. Methods The volume data is represented as level sets and a special set operator is defined and applied to filtering it. The small connected components, which are likely to be produced by impulsive noise, are eliminated after the filtering process. A fast algorithm that uses a heap data structure is also designed. Results Compared with traditional linear filters such as a Gaussian filter, this method preserves the fine structure features of the medical volume data while removing noise, and the fast algorithm developed by us reduces memory consumption and improves computing efficiency. The experimental results given illustrate the efficiency of the method and the fast algorithm. Conclusion The set operator-based method shows outstanding denoising properties in our experiment, especially for impulsive noise. The method has a wide variety of applications in the areas of volume visualization and high dimensional data processing.

  17. Applications of Phase Diagrams in Metallurgy and Ceramics: Proceedings of a Workshop Held at the National Bureau of Standards, Gaithersburg, Maryland, January 10-12, 1977. Volumes 1 [and] 2.

    Science.gov (United States)

    Carter, G. C., Ed.

    This document is a special National Bureau of Standards publication on a Workshop on Applications of Phase Diagrams in Metallurgy and Ceramics. The purposes of the Workshop were: (1) to assess the current national and international status of phase diagram determinations and evaluations for alloys, ceramics and semiconductors; (2) to determine the…

  18. Characterization of solar cells for space applications. Volume 11: Electrical characteristics of 2 ohm-cm, 228 micron wraparound solar cells as a function of intensity, temperature, and irradiation. [for solar electric propulsion

    Science.gov (United States)

    Anspaugh, B. E.; Beckert, D. M.; Downing, R. G.; Weiss, R. S.

    1980-01-01

    Parametric characterization data on Spectrolab 2 by 4 cm, 2 ohm/cm, 228 micron thick wraparound cell, a candidate for the Solar Electric Propulsion Mission, are presented. These data consist of the electrical characteristics of the solar cell under a wide range of temperature and illumination intensity combinations of the type encountered in space applications.

  19. Clinical Application of Three-Dimensional Reconstruction Technique for Breast Volume Measurement in Mammaplasty%CT数据三维重建测量乳房体积在乳房整形中的应用

    Institute of Scientific and Technical Information of China (English)

    王凌宇; 栾杰; 李彦生; 穆兰花; 穆大力; 王克明

    2012-01-01

    目的 探讨应用三维重建技术测量乳房体积和乳房假体体积,及其在乳房整形中的应用前景.方法 由CT影像扫描系统获得患者胸部的基本CT数据(层厚3 mm),将CT的二维数据导人计算机,应用 MINICS软件及MagicRP软件对59例胸廓或乳房不对称患者进行乳房体积差测量及乳房假体体积测量,根据测量结果为患者选择体积适当的假体, 术后测量患者双侧乳房各种径线,并评价其术后效果.结果 59例患者术后双侧乳房基本对称,乳房形态理想,取得了满意的效果.结论 本方法测量乳房体积准确可靠,在测量乳房和乳房假体体积方面具有实际的应用价值.%Objective To explore the feasibility of usinj; 3-D reconstruction technique tor the volume measurement of breast and the breast implant in mammaplasty. Methods The CT data was used lo reconstruct a digital prototype of ihe breast implant and the chest. The volumes of breast imp)ants and the volumetric difference of bilateral breast were then measured by the software. Measurements were performed on 59 women. Suitable implants were also selected for the patients affording to the results of measurements. The linear parameters of the bilateral breast were measured for evaluating the results. Results Fifty -nine Pali en Ls were all satisfied, as the shapes of postoperative breasts were ideality and almost symmetry. Conclusion 3-0 reconstruction technique is simple, accurate and repeatable. It offers a new way to solve the difficult problems in the measurement of breast and breast implant.

  20. Measurement of breakthrough volumes of volatile chemical warfare agents on a poly(2,6-diphenylphenylene oxide)-based adsorbent and application to thermal desorption-gas chromatography/mass spectrometric analysis.

    Science.gov (United States)

    Kanamori-Kataoka, Mieko; Seto, Yasuo

    2015-09-01

    To establish adequate on-site solvent trapping of volatile chemical warfare agents (CWAs) from air samples, we measured the breakthrough volumes of CWAs on three adsorbent resins by an elution technique using direct electron ionization mass spectrometry. The trapping characteristics of Tenax(®) TA were better than those of Tenax(®) GR and Carboxen(®) 1016. The latter two adsorbents showed non-reproducible breakthrough behavior and low VX recovery. The specific breakthrough values were more than 44 (sarin) L/g Tenax(®) TA resin at 20°C. Logarithmic values of specific breakthrough volume for four nerve agents (sarin, soman, tabun, and VX) showed a nearly linear correlation with the reciprocals of their boiling points, but the data point of sulfur mustard deviated from this linear curve. Next, we developed a method to determine volatile CWAs in ambient air by thermal desorption-gas chromatography (TD-GC/MS). CWA solutions that were spiked into the Tenax TA(®) adsorbent tubes were analyzed by a two-stage TD-GC/MS using a Tenax(®) TA-packed cold trap tube. Linear calibration curves for CWAs retained in the resin tubes were obtained in the range between 0.2pL and 100pL for sarin, soman, tabun, cyclohexylsarin, and sulfur mustard; and between 2pL and 100pL for VX and Russian VX. We also examined the stability of CWAs in Tenax(®) TA tubes purged with either dry or 50% relative humidity air under storage conditions at room temperature or 4°C. More than 80% sarin, soman, tabun, cyclohexylsarin, and sulfur mustard were recovered from the tubes within 2 weeks. In contrast, the recoveries of VX and Russian VX drastically reduced with storage time at room temperature, resulting in a drop to 10-30% after 2 weeks. Moreover, we examined the trapping efficiency of Tenax TA(®) adsorbent tubes for vaporized CWA samples (100mL) prepared in a 500mL gas sampling cylinder. In the concentration range of 0.2-2.5mg/m(3), >50% of sarin, soman, tabun, cyclohexylsarin, and HD were

  1. Measurement of breakthrough volumes of volatile chemical warfare agents on a poly(2,6-diphenylphenylene oxide)-based adsorbent and application to thermal desorption-gas chromatography/mass spectrometric analysis.

    Science.gov (United States)

    Kanamori-Kataoka, Mieko; Seto, Yasuo

    2015-09-01

    To establish adequate on-site solvent trapping of volatile chemical warfare agents (CWAs) from air samples, we measured the breakthrough volumes of CWAs on three adsorbent resins by an elution technique using direct electron ionization mass spectrometry. The trapping characteristics of Tenax(®) TA were better than those of Tenax(®) GR and Carboxen(®) 1016. The latter two adsorbents showed non-reproducible breakthrough behavior and low VX recovery. The specific breakthrough values were more than 44 (sarin) L/g Tenax(®) TA resin at 20°C. Logarithmic values of specific breakthrough volume for four nerve agents (sarin, soman, tabun, and VX) showed a nearly linear correlation with the reciprocals of their boiling points, but the data point of sulfur mustard deviated from this linear curve. Next, we developed a method to determine volatile CWAs in ambient air by thermal desorption-gas chromatography (TD-GC/MS). CWA solutions that were spiked into the Tenax TA(®) adsorbent tubes were analyzed by a two-stage TD-GC/MS using a Tenax(®) TA-packed cold trap tube. Linear calibration curves for CWAs retained in the resin tubes were obtained in the range between 0.2pL and 100pL for sarin, soman, tabun, cyclohexylsarin, and sulfur mustard; and between 2pL and 100pL for VX and Russian VX. We also examined the stability of CWAs in Tenax(®) TA tubes purged with either dry or 50% relative humidity air under storage conditions at room temperature or 4°C. More than 80% sarin, soman, tabun, cyclohexylsarin, and sulfur mustard were recovered from the tubes within 2 weeks. In contrast, the recoveries of VX and Russian VX drastically reduced with storage time at room temperature, resulting in a drop to 10-30% after 2 weeks. Moreover, we examined the trapping efficiency of Tenax TA(®) adsorbent tubes for vaporized CWA samples (100mL) prepared in a 500mL gas sampling cylinder. In the concentration range of 0.2-2.5mg/m(3), >50% of sarin, soman, tabun, cyclohexylsarin, and HD were

  2. New method for rapid solid-phase extraction of large-volume water samples and its application to non-target screening of North Sea water for organic contaminants by gas chromatography-mass spectrometry.

    Science.gov (United States)

    Weigel, S; Bester, K; Hühnerfuss, H

    2001-03-30

    A method has been developed that allows the solid-phase extraction of microorganic compounds from large volumes of water (10 l) for non-target analysis of filtered seawater. The filtration-extraction system is operated with glass fibre filter candles and the polymeric styrene-divinylbenzene sorbent SDB-1 at flow-rates as high as 500 ml/min. Recovery studies carried out for a couple of model substances covering a wide range of polarity and chemical classes revealed a good performance of the method. Especially for polar compounds (log Kow 3.3-0.7) quantitative recovery was achieved. Limits of detection were between 0.1 and 0.7 ng/l in the full scan mode of the MS. The suitability of the method for the analysis of marine water samples is demonstrated by the non-target screening of water from the German Bight for the presence of organic contaminants. In the course of this screening a large variety of substances was identified including pesticides, industrial chemicals and pharmaceuticals. For some of the identified compounds their occurrence in marine ecosystems has not been reported before, such as dichloropyridines, carbamazepine, propyphenazone and caffeine.

  3. Colloids in Paints Colloids and Interface Science, Volume 6

    CERN Document Server

    Tadros, Tharwat F

    2011-01-01

    The first modern approach to relate fundamental research to the applied science of colloids, this series bridges academic research and practical applications, thus providing the information vital to both. Written by the very best scientists in their respective disciplines, this volume describes the role of colloids in paints, highlighting the importance of fundamental research in industrial applications.For surface, polymer and physicochemists, materials scientists, and chemical engineers.

  4. Insular volume reduction in schizophrenia.

    Science.gov (United States)

    Saze, Teruyasu; Hirao, Kazuyuki; Namiki, Chihiro; Fukuyama, Hidenao; Hayashi, Takuji; Murai, Toshiya

    2007-12-01

    Structural and functional abnormalities of the insular cortex have been reported in patients with schizophrenia. Most studies have shown that the insular volumes in schizophrenia patients are smaller than those of healthy people. As the insular cortex is functio-anatomically divided into anterior and posterior subdivisons, recent research is focused on uncovering a specific subdivisional abnormality of the insula in patients with schizophrenia. A recent ROI-based volumetric MRI study demonstrated specific left anterior insular volume reduction in chronic schizophrenia patients (Makris N, Goldstein J, Kennedy D, Hodge S, Caviness V, Faraone S, Tsuang M, Seidman L (2006) Decreased volume of left and total anterior insular lobule in schizophrenia. Schizophr Res 83:155-171). On the other hand, our VBM-based volumetric study revealed a reduction in right posterior insular volume (Yamada M, Hirao K, Namiki C, Hanakawa T, Fukuyama H, Hayashi T, Murai T (2007) Social cognition and frontal lobe pathology in schizophrenia: a voxel-based morphometric study. NeuroImage 35:292-298). In order to address these controversial results, ROI-based subdivisional volumetry was performed using the MRI images from the same population we analyzed in our previous VBM-study. The sample group comprised 20 schizophrenia patients and 20 matched healthy controls. Patients with schizophrenia showed a global reduction in insular gray matter volumes relative to healthy comparison subjects. In a simple comparison of the volumes of each subdivision between the groups, a statistically significant volume reduction in patients with schizophrenia was demonstrated only in the right posterior insula. This study suggests that insular abnormalities in schizophrenia would include anterior as well as posterior parts. Each subdivisional abnormality may impact on different aspects of the pathophysiology and psychopathology of schizophrenia; these relationships should be the focus of future research.

  5. The volume of fluid method in spherical coordinates

    NARCIS (Netherlands)

    Janse, A.M.C.; Dijk, P.E.; Kuipers, J.A.M.

    2000-01-01

    The volume of fluid (VOF) method is a numerical technique to track the developing free surfaces of liquids in motion. This method can, for example, be applied to compute the liquid flow patterns in a rotating cone reactor. For this application a spherical coordinate system is most suited. The novel

  6. Annual Review of Applied Linguistics, Volume 5, 1984.

    Science.gov (United States)

    Kaplan, Robert B., Ed.

    This volume of the annual review includes introductory remarks by G. Richard Tucker and these papers: "Current Issues in Bilingualism: An Update of Directions in Research" (Braj B. Kachru); "Psycholinguistics: Application. The Writing System as a Native Language for the Deaf" (Danny D. Steinberg); "Sociolinguistics: Theory" (Monica Heller);…

  7. Waste isolation safeguards and security system. Volume 2. Bibliography

    International Nuclear Information System (INIS)

    The purpose of this study is to define the rationale and scope of the Waste Isolation System (WIS) safeguards system, to establish a set of proposed basic safeguards criteria, and to identify the areas requiring development of specific criteria and technology. The report also presents a proposed program schedule and provides an extensive bibliography, in volumes two and three of applicable reference safeguards documents

  8. Waste isolation safeguards and security system. Volume 3. Bibliography supplement

    International Nuclear Information System (INIS)

    The purpose of this study is to define the rationale and scope of the Waste Isolation System (WIS) safeguards system, to establish a set of proposed basic safeguards criteria, and to identify the areas requiring development of specific criteria and technology. The report also presents a proposed program schecule and provides an extensive bibliography in volumes two and three of applicable reference safeguards documents

  9. Development of application and studies of volume-capnography in critical patients%容量-呼气末二氧化碳分压波在危重患者中临床应用解析

    Institute of Scientific and Technical Information of China (English)

    江学成

    2011-01-01

    Background Volume PETCO2 is a sigal-wave plot based on the expired carbon dioxide fraction,which is the standard tool for understanding carbon dioxide elimination and the dead space. Objective The basic principles and clinical significance of normal and abnormal waveform of v-PETCO2 is introduced. Content v-PETCO2 wave morphology depends on production, transport (pulmonary perfusion) and diffusion of the carbon dioxide, as well as any changes in respiratory pathophysiology, v-PETCO2 can be used to study the dynamics of CO2. This plot yields three parts: first phase is carbon dioxide free;phase Ⅱ represents the transition between gas from the airways and alveolar gas, and phase Ⅲ represents alveolar gas. The respiratory dysfunction reduces ventilation in some units more than others, causing an increased scatter of ventilation/perfusion (V/Q)ratios and thus of the range of alveolar PCO2 values. They results in increased slope of phase 3 and three dead space estimates derived from the v-capnogram, including the anatomical dead space, alveolar dead space and physiological dead space. This can differentiate a patient with a pulmonary embolism from a healthy patient or a COPD, ARDS or asthma patients. Trend v-PETCO2 is the standard tool for understanding carbon dioxide elimination and the dead space concept.%背景容量-呼气末二氧化碳分压图(volume-capnogram,v-PETCO2)是根据呼吸周期中呼出气量对应CO2水平描记的单波图,是评价呼吸障碍患者死腔或分流的最有价值的无创性新工具。目的讲述v-PETCO2的基本原理、正常波形和异常波形的临床意义。内容v-PETCO2波的形态取决于CO2产生、运输(肺灌注)和弥散以及任何原因引起的肺病理生理学改变,可用来更好地了解和研究CO2动力学过程。v-PETCO2有3个呼气相:相Ⅰ,呼出的为无CO2的气道气体,相Ⅱ是气道和肺泡混合气体,相Ⅲ完全是肺泡气体。呼吸障碍时通气/灌注比

  10. iPhone 4s photoplethysmography: which light color yields the most accurate heart rate and normalized pulse volume using the iPhysioMeter Application in the presence of motion artifact?

    Science.gov (United States)

    Matsumura, Kenta; Rolfe, Peter; Lee, Jihyoung; Yamakoshi, Takehiro

    2014-01-01

    Recent progress in information and communication technologies has made it possible to measure heart rate (HR) and normalized pulse volume (NPV), which are important physiological indices, using only a smartphone. This has been achieved with reflection mode photoplethysmography (PPG), by using a smartphone's embedded flash as a light source and the camera as a light sensor. Despite its widespread use, the method of PPG is susceptible to motion artifacts as physical displacements influence photon propagation phenomena and, thereby, the effective optical path length. Further, it is known that the wavelength of light used for PPG influences the photon penetration depth and we therefore hypothesized that influences of motion artifact could be wavelength-dependant. To test this hypothesis, we made measurements in 12 healthy volunteers of HR and NPV derived from reflection mode plethysmograms recorded simultaneously at three different spectral regions (red, green and blue) at the same physical location with a smartphone. We then assessed the accuracy of the HR and NPV measurements under the influence of motion artifacts. The analyses revealed that the accuracy of HR was acceptably high with all three wavelengths (all rs > 0.996, fixed biases: -0.12 to 0.10 beats per minute, proportional biases: r =  -0.29 to 0.03), but that of NPV was the best with green light (r = 0.791, fixed biases: -0.01 arbitrary units, proportional bias: r = 0.11). Moreover, the signal-to-noise ratio obtained with green and blue light PPG was higher than that of red light PPG. These findings suggest that green is the most suitable color for measuring HR and NPV from the reflection mode photoplethysmogram under motion artifact conditions. We conclude that the use of green light PPG could be of particular benefit in ambulatory monitoring where motion artifacts are a significant issue. PMID:24618594

  11. Development and validation of a rapid and high-sensitivity liquid chromatography-tandem mass spectrometry assay for the determination of neostigmine in small-volume beagle dog plasma and its application to a pharmacokinetic study.

    Science.gov (United States)

    Cao, Di; Li, Wenxue; Zhao, Xin; Ye, Xiaolan; Sun, Fanlu; Li, Jinying; Song, Fenyun; Fan, Guorong

    2014-03-01

    A simple, rapid and high sensitive liquid chromatography-tandem mass spectrometry (LC-MS/MS) method for the determination of neostigmine in small-volume beagle dog plasma was developed to assess the plasma pharmacokinetics of neostigmine. After protein precipitation in a Sirocco 96-well filtration plate, the filtrate was directly injected into the LC-MS/MS system. The analytes were separated on a Hanbon Hedera CN column (100 × 4.6 mm, 5 µm) with a mobile phase composed of methanol-water (60:40, v/v) and the water containing 0.01% formic acid at a flow rate of 0.6mL/min, with a split ratio of 1:1 flowing 300 μL into the mass spectrometer. The run time was 3 min. Detection was accomplished by electrospray ionization source in multiple reactions monitoring mode with the precursor-to-product ion transitions m/z 223.0 → 72.0 and 306.0 → 140.0 for neostigmine and anisodamine (internal standard), respectively. The method was sensitive with a lower limit of quantitation of 0.1 ng/mL, and good linearity in the range 0.1-100ng/mL for neostigmine (r ≥ 0.998). All the validation data, such as accuracy, intra-run and inter-run precision, were within the required limits. The method was successfully applied to pharmacokinetic study of neostigmine methylsulfate injection in beagle dogs. PMID:24115102

  12. iPhone 4s photoplethysmography: which light color yields the most accurate heart rate and normalized pulse volume using the iPhysioMeter Application in the presence of motion artifact?

    Directory of Open Access Journals (Sweden)

    Kenta Matsumura

    Full Text Available Recent progress in information and communication technologies has made it possible to measure heart rate (HR and normalized pulse volume (NPV, which are important physiological indices, using only a smartphone. This has been achieved with reflection mode photoplethysmography (PPG, by using a smartphone's embedded flash as a light source and the camera as a light sensor. Despite its widespread use, the method of PPG is susceptible to motion artifacts as physical displacements influence photon propagation phenomena and, thereby, the effective optical path length. Further, it is known that the wavelength of light used for PPG influences the photon penetration depth and we therefore hypothesized that influences of motion artifact could be wavelength-dependant. To test this hypothesis, we made measurements in 12 healthy volunteers of HR and NPV derived from reflection mode plethysmograms recorded simultaneously at three different spectral regions (red, green and blue at the same physical location with a smartphone. We then assessed the accuracy of the HR and NPV measurements under the influence of motion artifacts. The analyses revealed that the accuracy of HR was acceptably high with all three wavelengths (all rs > 0.996, fixed biases: -0.12 to 0.10 beats per minute, proportional biases: r =  -0.29 to 0.03, but that of NPV was the best with green light (r = 0.791, fixed biases: -0.01 arbitrary units, proportional bias: r = 0.11. Moreover, the signal-to-noise ratio obtained with green and blue light PPG was higher than that of red light PPG. These findings suggest that green is the most suitable color for measuring HR and NPV from the reflection mode photoplethysmogram under motion artifact conditions. We conclude that the use of green light PPG could be of particular benefit in ambulatory monitoring where motion artifacts are a significant issue.

  13. iPhone 4s photoplethysmography: which light color yields the most accurate heart rate and normalized pulse volume using the iPhysioMeter Application in the presence of motion artifact?

    Science.gov (United States)

    Matsumura, Kenta; Rolfe, Peter; Lee, Jihyoung; Yamakoshi, Takehiro

    2014-01-01

    Recent progress in information and communication technologies has made it possible to measure heart rate (HR) and normalized pulse volume (NPV), which are important physiological indices, using only a smartphone. This has been achieved with reflection mode photoplethysmography (PPG), by using a smartphone's embedded flash as a light source and the camera as a light sensor. Despite its widespread use, the method of PPG is susceptible to motion artifacts as physical displacements influence photon propagation phenomena and, thereby, the effective optical path length. Further, it is known that the wavelength of light used for PPG influences the photon penetration depth and we therefore hypothesized that influences of motion artifact could be wavelength-dependant. To test this hypothesis, we made measurements in 12 healthy volunteers of HR and NPV derived from reflection mode plethysmograms recorded simultaneously at three different spectral regions (red, green and blue) at the same physical location with a smartphone. We then assessed the accuracy of the HR and NPV measurements under the influence of motion artifacts. The analyses revealed that the accuracy of HR was acceptably high with all three wavelengths (all rs > 0.996, fixed biases: -0.12 to 0.10 beats per minute, proportional biases: r =  -0.29 to 0.03), but that of NPV was the best with green light (r = 0.791, fixed biases: -0.01 arbitrary units, proportional bias: r = 0.11). Moreover, the signal-to-noise ratio obtained with green and blue light PPG was higher than that of red light PPG. These findings suggest that green is the most suitable color for measuring HR and NPV from the reflection mode photoplethysmogram under motion artifact conditions. We conclude that the use of green light PPG could be of particular benefit in ambulatory monitoring where motion artifacts are a significant issue.

  14. CTVision系统在分析鼻咽癌放疗过程靶区体积及其剂量学变化规律中的应用%Application of CTVision System in Analysis of the Change Law of the Target Volume and Dose for Nasopharyngeal Carcinoma in the Course of Radiotherapy

    Institute of Scientific and Technical Information of China (English)

    甘晓根; 徐子海; 廖福锡

    2015-01-01

    Objective To study the effectiveness of application of CTVision system in analysis of the change law of the target volume and dose for nasopharyngeal carcinoma in the course of radiotherapy. Methods Image-guided IMRT (Intensity-Modulated Radiation Therapy) was performed in 10 patients with nasopharyngeal carcinoma by using CTVision system to analyze the change law of the volume of target area and parotids. Then, the CT images were transmitted back to the TPS (Treatment Planning System) for recalculation and analysis of the dose for organs at risk.Results The volume of target area as well as the volume of bilateral parotids was diminishing with the progress of radiotherapy. And the volume of target area as well as the volume of right-sided parotids revealed obvious differences in the 4th week of radiotherapy from the pre-treatment volume. The volume of left-sided parotids revealed obvious differences in the 5th week of radiotherapy from the pre-treatment volume. Meanwhile, the radiation dose received by bilateral parotids increased gradually with the shrinkage of the volume, and was positively associated with the shrinkage degree (Right-sided parotids:r=0.471,P=0.036; Left-sided parotids:r=0.578,P=0.008).Conclusion For nasopharyngeal carcinoma patients who were experiencing IMRT, the volume of target area and parotids was shrinking with the progress of radiotherapy, leading to the increasing of the dose for organs. In view of this, it was suggested to redraw the outline of the target area and redesign the radiotherapy plan in the 4th to 5th week in of IMRT, which would improve the local control rate of nasopharyngeal carcinoma and reduce the side effects of radiation.%目的:探讨CTVision系统在分析鼻咽癌放疗过程靶区体积及其剂量学变化规律中的应用价值。方法采用CTVision系统对10例鼻咽癌患者进行图像引导调强放疗,分析鼻咽癌靶区及腮腺体积在放疗过程中的变化规律。并将采集到的CT图像传

  15. Symmetry Breaking in Finite Volume

    Institute of Scientific and Technical Information of China (English)

    LIU Chuan

    2000-01-01

    Spontaneous symmetry breaking is a cooperative phenomenon for systems with infinitely many degrees of freedom and it plays an essential role in quantum field theories. Lattice O(N) model is studied within the Hamiltonian approach using an adiabatic approximation. It is shown that the low-lying spectrum of the system in the broken phase can be understood by using the adiabatic, or Born-Oppenheimer approximation, which turns out to become an expansion in the inverse power of volume. In the infinite volume limit, the symmetry is broken while in the finite volume the slow rotation of the zero-momentum mode restores the symmetry and gives rise to the rotator spectrum, which has been observed in realistic Monte Carlo simulations.

  16. Principles of modern radar radar applications

    CERN Document Server

    Scheer, James A

    2013-01-01

    Principles of Modern Radar: Radar Applications is the third of the three-volume seriesof what was originally designed to be accomplished in one volume. As the final volumeof the set, it finishes the original vision of a complete yet bounded reference for radartechnology. This volume describes fifteen different system applications or class ofapplications in more detail than can be found in Volumes I or II.As different as the applications described, there is a difference in how these topicsare treated by the authors. Whereas in Volumes I and II there is strict adherence tochapter format and leve

  17. Gas volume contents within a container, smart volume instrument

    Science.gov (United States)

    Kelley, Anthony R. (Inventor); Van Buskirk, Paul D. (Inventor)

    2008-01-01

    A method for determining the volume of an incompressible gas in a system including incompressible substances in a zero-gravity environment. The method includes inducing a volumetric displacement within a container and measuring the resulting pressure change. From this data, the liquid level can be determined.

  18. Plasmas physic. Volume 1. Physique des Plasmas. Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Delcroix, J.L. (Paris-11 Univ., 91 - Orsay (France)); Bers, A. (Massachusetts Inst. of Tech., Cambridge, MA (United States). Dept. of Electrical Engineering Massachusetts Inst. of Tech., Cambridge, MA (United States). Plasma Fusion Center Massachusetts Inst. of Tech., Cambridge, MA (United States). Research Lab. of Electronics)

    1994-01-01

    An introduction to plasmas physic is done with qualitative and elementary calculus. Trajectory in a magnetic field, elastic and inelastic collisions, macroscopic description of low ionized gases, an hydrodynamic description of waves on electrons beams, and of instabilities in plasmas current are the main fields covered by this first volume. (A.B.). 369 refs., figs., tabs.

  19. Resource Conservation and Recovery Act, Part B Permit Application [for the Waste Isolation Pilot Plant (WIPP)]. Chapter E, Appendix E1, Chapter L, Appendix L1: Volume 12, Revision 3

    Energy Technology Data Exchange (ETDEWEB)

    1993-01-01

    The Waste Isolation Pilot Plant (WIPP) Project was authorized by the US Department of Energy 5 (DOE) National Security and Military Applications of the Nuclear Energy Authorization Act of 1980 (Public Law 96-164). Its legislative mandate is to provide a research and development facility to demonstrate the safe disposal of radioactive waste resulting from national defense programs and activities. To fulfill this mandate, the WIPP facility has been designed to perform scientific investigations of the behavior of bedded salt as a repository medium and the interactions between the soft and radioactive wastes. In 1991, DOE proposed to initiate a experimental Test Phase designed to demonstrate the performance of the repository. The Test Phase activities involve experiments using transuranic (TRU) waste typical of the waste planned for future disposal at the WIPP facility. Much of this TRU waste is co-contaminated with chemical constituents which are defined as hazardous under HWMR-7, Pt. II, sec. 261. This waste is TRU mixed waste and is the subject of this application. Because geologic repositories, such as the WIPP facility, are defined under the Resource Conservation and Recovery Act (RCRA) as land disposal facilities, the groundwater monitoring requirements of HWMR-7, PLV, Subpart X, must be addressed. HWMR-7, Pt. V, Subpart X, must be addressed. This appendix demonstrates that groundwater monitoring is not needed in order to demonstrate compliance with the performance standards; therefore, HWMR-7, Pt.V, Subpart F, will not apply to the WIPP facility.

  20. Planimetric determination of lung volume

    International Nuclear Information System (INIS)

    The total volume of the lungs was determined by digital planimetry in 102 patients with emphysema and 33 normal controls aged between 30 and 79 years. The results were compared with the findings obtained from spirometric measurements. Mean values showed a significant relationship to age, body size and body surface. Planimetrically determined lung volume did not show a linear relationship with age, but increased after 60 years. Beyong 60 years, spirometric findings were lower because of an increase in the number of patients with emphysema. The results have shown that digital planimetry is a useful addition to spirometry. (orig.)

  1. Large volume cryogenic silicon detectors

    Energy Technology Data Exchange (ETDEWEB)

    Braggio, C. [Dipartimento di Fisica, Universita di Padova, via Marzolo 8, 35131 Padova (Italy); Boscardin, M. [Fondazione Bruno Kessler (FBK), via Sommarive 18, I-38100 Povo (Italy); Bressi, G. [INFN sez. di Pavia, via Bassi 6, 27100 Pavia (Italy); Carugno, G.; Corti, D. [INFN sez. di Padova, via Marzolo 8, 35131 Padova (Italy); Galeazzi, G. [INFN lab. naz. Legnaro, viale dell' Universita 2, 35020 Legnaro (Italy); Zorzi, N. [Fondazione Bruno Kessler (FBK), via Sommarive 18, I-38100 Povo (Italy)

    2009-12-15

    We present preliminary measurements for the development of a large volume silicon detector to detect low energy and low rate energy depositions. The tested detector is a one cm-thick silicon PIN diode with an active volume of 31 cm{sup 3}, cooled to the liquid helium temperature to obtain depletion from thermally-generated free carriers. A thorough study has been done to show that effects of charge trapping during drift disappears at a bias field value of the order of 100V/cm.

  2. GPU-Based 3D Cone-Beam CT Image Reconstruction for Large Data Volume

    OpenAIRE

    Xing Zhao; Jing-jing Hu; Peng Zhang

    2009-01-01

    Currently, 3D cone-beam CT image reconstruction speed is still a severe limitation for clinical application. The computational power of modern graphics processing units (GPUs) has been harnessed to provide impressive acceleration of 3D volume image reconstruction. For extra large data volume exceeding the physical graphic memory of GPU, a straightforward compromise is to divide data volume into blocks. Different from the conventional Octree partition method, a new partition scheme is proposed...

  3. Liquefied natural gas as a transportation fuel for heavy-duty trucks: Volume I

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-01

    This document contains Volume 1 of a three-volume manual designed for use with a 2- to 3-day liquefied natural gas (LNG) training course. Transportation and off-road agricultural, mining, construction, and industrial applications are discussed. This volume provides a brief introduction to the physics and chemistry of LNG; an overview of several ongoing LNG projects, economic considerations, LNG fuel station technology, LNG vehicles, and a summary of federal government programs that encourage conversion to LNG.

  4. Brookhaven National Laboratory 2008 Site Environment Report Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Brookhaven National Laboratory

    2009-10-01

    Brookhaven National Laboratory (BNL) prepares an annual Site Environmental Report (SER) in accordance with DOE Order 231.1A, Environment, Safety and Health Reporting of the U.S. Department of Energy. The report is written to inform the public, regulators, employees, and other stakeholders of the Laboratory's environmental performance during the calendar year in review. Volume I of the SER summarizes environmental data; environmental management performance; compliance with applicable DOE, federal, state, and local regulations; and performance in restoration and surveillance monitoring programs. BNL has prepared annual SERs since 1971 and has documented nearly all of its environmental history since the Laboratory's inception in 1947. Volume II of the SER, the Groundwater Status Report, also is prepared annually to report on the status of and evaluate the performance of groundwater treatment systems at the Laboratory. Volume II includes detailed technical summaries of groundwater data and its interpretation, and is intended for internal BNL users, regulators, and other technically oriented stakeholders. A brief summary of the information contained in Volume II is included in this volume in Chapter 7, Groundwater Protection. Both reports are available in print and as downloadable files on the BNL web page at http://www.bnl.gov/ewms/ser/. An electronic version on compact disc is distributed with each printed report. In addition, a summary of Volume I is prepared each year to provide a general overview of the report, and is distributed with a compact disc containing the full report.

  5. Liquid volume monitoring based on ultrasonic sensor and Arduino microcontroller

    Science.gov (United States)

    Husni, M.; Siahaan, D. O.; Ciptaningtyas, H. T.; Studiawan, H.; Aliarham, Y. P.

    2016-04-01

    Incident of oil leakage and theft in oil tank often happens. To prevent it, the liquid volume insides the tank needs to be monitored continuously. Aim of the study is to calculate the liquid volume inside oil tank on any road condition and send the volume data and location data to the user. This research use some ultrasonic sensors (to monitor the fluid height), Bluetooth modules (to sent data from the sensors to the Arduino microcontroller), Arduino Microcontroller (to calculate the liquid volume), and also GPS/GPRS/GSM Shield module (to get location of vehicle and sent the data to the Server). The experimental results show that the accuracy rate of monitoring liquid volume inside tanker while the vehicle is in the flat road is 99.33% and the one while the vehicle is in the road with elevation angle is 84%. Thus, this system can be used to monitor the tanker position and the liquid volume in any road position continuously via web application to prevent illegal theft.

  6. Application of semi-automated measurement of liver volume in living donor liver transplantation%多层螺旋CT半自动法测量肝体积在成人活体肝移植中的应用

    Institute of Scientific and Technical Information of China (English)

    龚必焱; 季倩; 龙淼淼; 沈文; 祁吉

    2011-01-01

    目的 探讨多层螺旋CT(MSCT)半自动法测量右半供肝体积的准确性,及该方法在活体肝移植(LDLT)中的应用价值.方法 对56例供者术前行MSCT四期增强扫描,然后分别根据MSCT图像手动绘图(简称:手动法)计算右半供肝体积(V手)和应用IQQA(R)-liver肝脏诊断辅助分析系统进行半自动化绘图(简称:半自动法)计算右半供肝体积(V半),将两种方法计算的右半供肝体积与术中经水置换法实测的右半供肝体积(V术)进行相关分析和Bland-Altman检查,得出其线性回归方程.结果 V半、V手和V术分别为(818.60±161.43)、(880.16±169.92)和(669.84±141.37)cm3;半自动法和手动法测量供肝体积与术中实测肝体积均显著相关(r值分别为0.778和0.746,P<0.05),其线性回归方程分别为V术=V半×0.681+112.26,V术=V手×0.620+123.81.半自动法测量肝体积与术中实测肝体积的差值为148.76cm3,95%可信区间为121.57~175.95 cm3,吻合限为-354.135~56.62 cm3,手动法测量肝体积与术中实测肝体积的差值为210.33 cm3,95%可信区间为180.09~240.56 cm3,吻合限为-438.66~18.01cm3.结论 半自动法测量LDLT右半供肝体积比目前最常用的手动法更为准确.%Objective To evaluate the accuracy of multi-detector spiral CT (MSCT) semiautomated volumetric measurement of right lobes and its value in living donor liver transplantation (LDLT). Methods Fifty-six donors underwent four phases MSCT. Pre-operative liver volumes of two measurements [IQQA(R)-liver semi-automated (Vs) and manual volume (Vm) measurements] in portal vein phase were compared with intra-operative measurement (Vio) by means of water displacement. Results Correlation analysis and Bland-Altman tests were used for statistical analysis.Results Pre-operative measurements of grafts resulted in a mean Vs, Vm, Vio of (818. 60 ± 161.43)cm3 , (880. 16 ± 169. 92) cm3 and (669. 84 ± 141.37) cm3 respectively. All corresponding pre-and intra

  7. 40 CFR 791.48 - Production volume.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 31 2010-07-01 2010-07-01 true Production volume. 791.48 Section 791... (CONTINUED) DATA REIMBURSEMENT Basis for Proposed Order § 791.48 Production volume. (a) Production volume.... (b) For the purpose of determining fair reimbursement shares, production volume shall include...

  8. The relative volume growth of minimal submanifolds

    DEFF Research Database (Denmark)

    Markvorsen, Steen; Palmer, V.

    2002-01-01

    The volume growth of certain well-defined subsets of minimal submanifolds in riemannian spaces are compared with the volume growth of balls and spheres ill space forms of constant curvature.......The volume growth of certain well-defined subsets of minimal submanifolds in riemannian spaces are compared with the volume growth of balls and spheres ill space forms of constant curvature....

  9. Modern Chemical Technology, Volume 1.

    Science.gov (United States)

    Pecsok, Robert L.; Chapman, Kenneth

    This volume is the first in a series of the ACS "Modern Chemical Technology" (ChemTeC) curriculum which is to prepare chemical technicians. The chapters concentrate on gas chromatography, tests for purity, properties of gases, and gas measurements. Included is the appropriate content, exercises, laboratory activities, and all needed mathematics.…

  10. PATRAM '80. Proceedings. Volume 1

    International Nuclear Information System (INIS)

    Volume 1 contains papers from the following sessions: Plenary Session; Regulations, Licensing and Standards; LMFBR Systems Concepts; Risk/Safety Assessment I; Systems and Package Design; US Institutional Issues; Risk/Safety Assessment II; Leakage, Leak Rate and Seals; Poster Session A; Operations and Systems Experience I; Manufacturing Processes and Materials; and Quality Assurance and Maintenance. Individual papers were processed. (LM)

  11. Moment Maps and Equivariant Volumes

    Institute of Scientific and Technical Information of China (English)

    Alberto DELLA VEDOVA; Roberto PAOLETTI

    2007-01-01

    The study of the volume of big line bundles on a complex projective manifold M has been one of the main veins in the recent interest in the asymptotic properties of linear series. In this article,we consider an equivariant version of this problem, in the presence of a linear action of a reductive group on M.

  12. Summation of IMS Volume Frequencies.

    Science.gov (United States)

    Gordillo, Frank

    A computer program designed to produce summary information on the data processing volume of the Southwest Regional Laboratory's (SWRL) Instructional Management System (IMS) is described. Written in FORTRAN IV for use on an IBM 360 Model 91, the program sorts IMS input data on the basis of run identifier and on the basis of classroom identification…

  13. PATRAM '80. Proceedings. Volume 2

    International Nuclear Information System (INIS)

    Volume 2 contains papers from the following sessions: Safeguards-Related Problems; Neutronics and Criticality; Operations and Systems Experience II; Plutonium Systems; Intermediate Storage in Casks; Operations and Systems Planning; Institutional Issues; Structural and Thermal Evaluation I; Poster Session B; Extended Testing I; Structural and Thermal Evaluation II; Extended Testing II; and Emergency Preparedness and Response. Individual papers were processed. (LM)

  14. Plasma volume in acute hypoxia

    DEFF Research Database (Denmark)

    Poulsen, T D; Klausen, T; Richalet, J P;

    1998-01-01

    Exposure to acute hypoxia is associated with changes in body fluid homeostasis and plasma volume (PV). This study compared a dye dilution technique using Evans' blue (PV[Evans']) with a carbon monoxide (CO) rebreathing method (PV[CO]) for measurements of PV in ten normal subjects at sea level...

  15. Editorial, Volume 5, Issue 1

    Directory of Open Access Journals (Sweden)

    Kristy L. Archuleta

    2014-08-01

    Full Text Available Welcome to Volume 5, Issue 1 of the Journal of Financial Therapy! In this issue, four scholarly papers are presented along with two profiles and a book review. These four papers address very important issues, such as mental health therapists’ competency in working with financial issues, financial stress of college students, parental messages about money, and financial advice media.

  16. History of CERN. Volume 3

    International Nuclear Information System (INIS)

    The present volume continues the story of the history of the European Organization for Nuclear Research (CERN) in Geneva, Switzerland, concentrating on the years between the mid 1960s and the late 1970s. Whereas the first two volumes were the product of a team of historians, this book is rather a collection of studies by authors with very different professional backgrounds and institutional locations. It also differs from the predecessor volumes in the fact that it consists of distinct case studies dealing with a number of issues deemed important. The first part of this volume, containing contributions by historians of science, perceives the laboratory as being at the node of a complex of interconnected relationships between scientists and science managers on the staff, the users in the member states, and the governments which were called upon to finance the laboratory. In part 2 the physical results, obtained at CERN, are surveyed, while in part 3 two chapters are presented, one on engineering and technology, and the other on the research and development of electronic position detectors

  17. Octree-based Volume Sculpting

    DEFF Research Database (Denmark)

    Bærentzen, Jakob Andreas

    1998-01-01

    A volume sculpting system is presented. The system provides tools for interactive editing of a voxel raster that is stored in an octree data structure. Two different modes of sculpting are supported: Sculpting by adding and subtracting solids, and sculpting with tools that are based on a spray ca...... metaphor. The possibility of extending the method to support multiresolution sculpting is discussed....

  18. Eddy current manual, volume 2

    International Nuclear Information System (INIS)

    This report on eddy current testing is divided into three sections: (a) Demonstration of Basic Principles, (b) Practical (Laboratory) Tests and, (c) Typical Certification Questions. It is intended to be used as a supplement to ΣEddy Current Manual, Volume 1Σ (AECL-7523) during CSNDT Foundation Level II and III courses

  19. PATRAM '80. Proceedings. Volume 2

    Energy Technology Data Exchange (ETDEWEB)

    Huebner, H.W. (ed.)

    1980-01-01

    Volume 2 contains papers from the following sessions: Safeguards-Related Problems; Neutronics and Criticality; Operations and Systems Experience II; Plutonium Systems; Intermediate Storage in Casks; Operations and Systems Planning; Institutional Issues; Structural and Thermal Evaluation I; Poster Session B; Extended Testing I; Structural and Thermal Evaluation II; Extended Testing II; and Emergency Preparedness and Response. Individual papers were processed. (LM)

  20. PATRAM '80. Proceedings. Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Huebner, H.W. (ed.)

    1980-01-01

    Volume 1 contains papers from the following sessions: Plenary Session; Regulations, Licensing and Standards; LMFBR Systems Concepts; Risk/Safety Assessment I; Systems and Package Design; US Institutional Issues; Risk/Safety Assessment II; Leakage, Leak Rate and Seals; Poster Session A; Operations and Systems Experience I; Manufacturing Processes and Materials; and Quality Assurance and Maintenance. Individual papers were processed. (LM)

  1. Watergift klein volume substraat lelie

    NARCIS (Netherlands)

    Kok, B.J.

    2005-01-01

    In eerder onderzoek is gebleken dat het mogelijk is om lelies te broeien op een klein volume substraat. Deze teelt biedt vele mogelijkheden voor een hogere productie per m² en verdere technische ontwikkelingen (o.a. automatisering). Voorwaarde voor een goed teeltresultaat is een goede vochtvoorzieni

  2. The African Experience. Volume I: Syllabus Lectures; Volume II: Bibliographic References; Volume IIIA: Introductory Essays; Volume IIIB: Introductory Essays.

    Science.gov (United States)

    Paden, John N.; Soja, Edward W.

    In response to demands for more and better teaching about Africa in American higher education, the US Office of Education requested that the Program of African Studies at Northwestern University generate a set of teaching materials which could be used in introductory undergraduate courses. Included in these volumes, these materials provide…

  3. Wavelet-Based Volume Visualization

    NARCIS (Netherlands)

    Roerdink, Jos B.T.M.; Westenberg, Michel A.

    1999-01-01

    We consider multiresolution visualization of large volume data sets based on wavelets. Starting from a wavelet decomposition of the data, a low resolution image is computed; this approximation can be successively refined. The practical need for such a multiresolution approach is motivated. The mathe

  4. Spectrum '86: Proceedings: Volume 2

    International Nuclear Information System (INIS)

    This document, Volume 2, contains 96 papers on various aspects of radioactive waste management. Session topics include decontamination and decommissioning/endash/industry experience, characterization and safety, techniques, facility and plant decontamination; TRU waste management; regulatory aspects; economics; environmental issues and impacts; construction, operation, and maintenance. Individual papers were processed separately for the data bases

  5. Partial specific volume of xanthan

    Science.gov (United States)

    Wohlfarth, Ch.

    This document is part of Subvolume D2 'Polymer Solutions - Physical Properties and their Relations I (Thermodynamic Properties: PVT -Data and miscellaneous Properties of polymer Solutions) of Volume 6 `Polymers' of Landolt-Börnstein - Group VIII `Advanced Materials and Technologies'.

  6. Volume Holograms in Photopolymers: Comparison between Analytical and Rigorous Theories

    Directory of Open Access Journals (Sweden)

    Augusto Beléndez

    2012-08-01

    Full Text Available There is no doubt that the concept of volume holography has led to an incredibly great amount of scientific research and technological applications. One of these applications is the use of volume holograms as optical memories, and in particular, the use of a photosensitive medium like a photopolymeric material to record information in all its volume. In this work we analyze the applicability of Kogelnik’s Coupled Wave theory to the study of volume holograms recorded in photopolymers. Some of the theoretical models in the literature describing the mechanism of hologram formation in photopolymer materials use Kogelnik’s theory to analyze the gratings recorded in photopolymeric materials. If Kogelnik’s theory cannot be applied is necessary to use a more general Coupled Wave theory (CW or the Rigorous Coupled Wave theory (RCW. The RCW does not incorporate any approximation and thus, since it is rigorous, permits judging the accurateness of the approximations included in Kogelnik’s and CW theories. In this article, a comparison between the predictions of the three theories for phase transmission diffraction gratings is carried out. We have demonstrated the agreement in the prediction of CW and RCW and the validity of Kogelnik’s theory only for gratings with spatial frequencies higher than 500 lines/mm for the usual values of the refractive index modulations obtained in photopolymers.

  7. Stereological estimation of the mean and variance of nuclear volume from vertical sections

    DEFF Research Database (Denmark)

    Sørensen, Flemming Brandt

    1991-01-01

    The application of assumption-free, unbiased stereological techniques for estimation of the volume-weighted mean nuclear volume, nuclear vv, from vertical sections of benign and malignant nuclear aggregates in melanocytic skin tumours is described. Combining sampling of nuclei with uniform probab...... and reproducible malignancy grading of cancers....

  8. Viability Assessment of a Repository at Yucca Mountain. Volume 1: Introduction and Site Characteristics

    Energy Technology Data Exchange (ETDEWEB)

    None

    1998-12-01

    This first volume contains an introduction to the viability assessment, including the purpose, scope, waste forms, technical challenges, an historical perspective, regulatory framework, management of the repository, technical components, preparations for the license application, and repository milestones after the assessment. The second part of this first volume addresses characteristics of the Yucca Mountain site.

  9. System 80+{trademark} Standard Design: CESSAR design certification. Volume 16: Amendment I

    Energy Technology Data Exchange (ETDEWEB)

    1990-12-21

    This report, entitled Combustion Engineering Standard Safety Analysis Report - Design Certification (CESSAR-DC), has been prepared in support of the industry effort to standardize nuclear plant designs. These volumes describe the Combustion Engineering, Inc. System 80+{trademark} Standard Design. This Volume 16 details the application of Human Factors Engineering in the design process.

  10. The Volume Holographic Optical Storage Potential in Azobenzene Containing Polymers

    DEFF Research Database (Denmark)

    Hvilsted, Søren; Sanchez, Carlos; Alcalá, Rafael

    2009-01-01

    Volume holographic data storage is one of the most promising techniques to improve both the storage capacity of devices and the transfer data rate. Among the materials proposed as storage data media, azobenzene containing polymers have received much attention. Some of their properties seem...... to be suitable for holographic storage applications. However, they still present several problems, mainly those related with light sensitivity, response time and stability of the stored information. In this article we review the work performed on volume holographic storage using azobenzene containing polymers...

  11. Activity report 1990-1992 and proceedings. Volume II

    International Nuclear Information System (INIS)

    A report of the European Seismological Commission (ESC) on 1990-1992 activities and Proceedings of the General Assembly of the ESC are presented in two volumes. Volume II covers the following topics: study of seismic sound, seismotectonic analysis, deep seismic sounding, the three-dimensional structure of the European lithosphere-asthenosphere system, complexity in earthquake occurrence, earthquake hazard, strong and weak earthquake ground motions, macroseismology, microzonation, and applications in earthquake engineering. One paper dealing with the connection between seismicity and the CO2-222Rn content in spring water has been inputted to INIS. (Z.S.)

  12. Safety of magnetic fusion facilities: Volume 2, Guidance

    International Nuclear Information System (INIS)

    This document provides guidance for the implementation of the requirements identified in Vol. 1 of this Standard. This guidance is intended for the managers, designers, operators, and other personnel with safety responsibilities for facilities designated as magnetic fusion facilities. While Vol. 1 is generally applicable in that requirements there apply to a wide range of fusion facilities, this volume is concerned mainly with large facilities such as the International Thermonuclear Experimental Reactor (ITER). Using a risk-based prioritization, the concepts presented here may also be applied to other magnetic fusion facilities. This volume is oriented toward regulation in the Department of Energy (DOE) environment

  13. Safety of magnetic fusion facilities: Volume 2, Guidance

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-07-01

    This document provides guidance for the implementation of the requirements identified in Vol. 1 of this Standard. This guidance is intended for the managers, designers, operators, and other personnel with safety responsibilities for facilities designated as magnetic fusion facilities. While Vol. 1 is generally applicable in that requirements there apply to a wide range of fusion facilities, this volume is concerned mainly with large facilities such as the International Thermonuclear Experimental Reactor (ITER). Using a risk-based prioritization, the concepts presented here may also be applied to other magnetic fusion facilities. This volume is oriented toward regulation in the Department of Energy (DOE) environment.

  14. Activity Report, 1990 - 1992 and proceedings, volume 2

    Science.gov (United States)

    Kottnauer, Ing. Pavel

    A report of the European Seismological Commission (ESC) on 1990-1992 activities and Proceedings of the General Assembly of the ESC are presented in two volumes. Volume 2 covers the following topics: study of seismic sound, seismotectonic analysis, deep seismic sounding, the three-dimensional structure of the European lithosphere-asthenosphere system, complexity in earthquake occurrence, earthquake hazard, strong and weak earthquake ground motions, macroseismology, microzonation, and applications in earthquake engineering. One paper dealing with the connection between seismicity and the CO2- (sup 222)Rn content in spring water has been inputted to INIS.

  15. Finite Volumes Discretization of Topology Optimization Problems

    DEFF Research Database (Denmark)

    Evgrafov, Anton; Gregersen, Misha Marie; Sørensen, Mads Peter

    Utilizing control in the coecients of partial dierential equations (PDEs) for the purpose of optimal design, or topology optimization, is a well established technique in both academia and industry. Advantages of using control in the coecients for optimal design purposes include the exibility...... of the induced parametrization of the design space that allows optimization algorithms to eciently explore it, and the ease of integration with existing computational codes in a variety of application areas, the simplicity and eciency of sensitivity analyses|all stemming from the use of the same grid throughout...... the optimization procedure. As topology optimization is gaining maturity, the method is applied to increasingly more complex coupled multi-physical problems. As a result it becomes vital to utilize robust and mature PDE solvers within a topology optimization framework. Finite volume methods (FVMs) represent...

  16. Morphological pyramids in multiresolution MIP rendering of large volume data : Survey and new results

    NARCIS (Netherlands)

    Roerdink, Jos B.T.M.

    2005-01-01

    We survey and extend nonlinear signal decompositions based on morphological pyramids, and their application to multiresolution maximum intensity projection (MIP) volume rendering with progressive refinement and perfect reconstruction. The structure of the resulting multiresolution rendering algorith

  17. Geothermal completion technology life cycle cost model (GEOCOM). Volume I. Final report. Volume II. User instruction manual

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, E.R.; Hoessel, W.C.; Mansure, A.J.; McKissen, P.

    1982-07-01

    Just as with petroleum wells, drilling and completing a geothermal well at minimum original cost may not be the most cost-effective way to exploit the resource. The impacts of the original completion activities on production and costs later in the life of the well must also be considered. In order to evaluate alternate completion and workover technologies, a simple computer model has been developed to compare total life-cycle costs for a geothermal well to total production or injection. Volume I discusses the mechanics of the model and then presents detailed results from its application to different completion and workover questions. Volume II is the user instruction manual.

  18. O*NET Final Technical Report. Volume I [and] Volume II [and] Volume III.

    Science.gov (United States)

    Peterson, Norman G.; Mumford, Michael D.; Borman, Walter C.; Jeanneret, P. Richard; Fleishman, Edwin A.; Levin, Kerry Y.

    This document contains the three volumes of the technical report for development of the prototype of the Occupational Information Network (O*NET), which is intended to replace the "Dictionary of Occupational Titles.""General Introduction" (Norman G. Peterson) presents an overview of O*NET's purpose, content, and structure. "Research Method:…

  19. Diffuse volume transport in fluids

    Science.gov (United States)

    Brenner, Howard

    2010-10-01

    The diffuse flux of volume j in a single-component liquid or gas, the subject of this paper, is a purely molecular quantity defined as the difference between the flux of volume n and the convective flux of volume nvˆ carried by the flowing mass, with n the mass flux, vˆ=1/ρ the specific volume, and ρ the mass density. Elementary statistical-mechanical arguments are used to derive the linear constitutive equation j=DS∇lnρ, valid in near-equilibrium fluids from which body forces are absent. Here, DS is the fluid’s self-diffusion coefficient. The present derivation is based on Einstein’s mesoscopic Brownian motion arguments, albeit applied here to volume- rather than particle-transport phenomena. In contrast to these mesoscale arguments, all prior derivations were based upon macroscale linear irreversible thermodynamic (LIT) arguments. DS replaces the thermometric diffusivity α as the phenomenological coefficient appearing in earlier, ad hoc, derivations. The prior scheme based on α, which had been shown to accord with Burnett’s well-known gas-kinetic constitutive data for the heat flux and viscous stress, carries over intact to now show comparable accord of DS with these same data, since for gases the dimensionless Lewis number Le=α/DS is essentially unity. On the other hand for most liquids, where Le≫1, use of DS in place of α is shown to agree much better with existing experimental data for liquids. For the case of binary mixtures it is shown for the special case of isothermal, isobaric, force-free, Fick’s law-type molecular diffusion processes that j=D∇lnρ, where D is the binary diffusion coefficient. In contrast with the preceding use in the single-component case of both mesoscopic and LIT models to obtain a constitutive equation for j, the corresponding mixture result is derived here without use of any physical model whatsoever. Rather, the derivation effectively requires little more than the respective definitions of the diffuse volume

  20. COMPARISON BETWEEN MULTICOPTER UAV AND TOTAL STATION FOR ESTIMATING STOCKPILE VOLUMES

    OpenAIRE

    Arango, C.; Morales, C.A.

    2015-01-01

    Currently the UAV (Unmanned Aerial Vehicle) have become an alternative for different engineering applications, especially in surveying, one of these applications is the calculation of volumes of stockpiled material, but there are questions about its accuracy and efficiency, the purpose of this article is to compare traditional surveying methods for estimating total volumes through data obtained by total stations and data obtained by a multicopter UAV. In order to answer these questions we obt...

  1. Review of Random Phase Encoding in Volume Holographic Storage

    Directory of Open Access Journals (Sweden)

    Wei-Chia Su

    2012-09-01

    Full Text Available Random phase encoding is a unique technique for volume hologram which can be applied to various applications such as holographic multiplexing storage, image encryption, and optical sensing. In this review article, we first review and discuss diffraction selectivity of random phase encoding in volume holograms, which is the most important parameter related to multiplexing capacity of volume holographic storage. We then review an image encryption system based on random phase encoding. The alignment of phase key for decryption of the encoded image stored in holographic memory is analyzed and discussed. In the latter part of the review, an all-optical sensing system implemented by random phase encoding and holographic interconnection is presented.

  2. ICONE-4: Proceedings. Volume 1 -- Part A: Basic technological advances

    International Nuclear Information System (INIS)

    The proceedings of this conference are divided into 5 volumes. Volume one is subdivided into Parts A and B. Here in Part A, the following subjects are covered: fundamental thermal hydraulics; structural analysis and design of nuclear facilities; numerical and experimental two-phase flow developments; advances in reactor pressure vessel technology; advances in computational thermal hydraulics; thermal hydraulics of nuclear safety and reliability; advanced reactors thermal hydraulic safety--natural circulation; advances in numerical simulation of steam explosions; computational and experimental two-phase flow developments; two-phase flow and heat transfer fundamentals; advances in stability analysis; and material issues in nuclear applications. Separate abstracts were prepared for most papers in this volume

  3. Design of Finite Element Tools for Coupled Surface and Volume Meshes

    Institute of Scientific and Technical Information of China (English)

    Daniel K(o)ster; Oliver Kriessl; Kunibert G. Siebert

    2008-01-01

    Many problems with underlying variational structure involve a coupling of volume with surface effects. A straight-forward approach in a finite element discretization is to make use of the surface triangulation that is naturally induced by the volume triangulation. In an adaptive method one wants to facilitate "matching" local mesh modifications, i.e., local refinement and/or coarsening, of volume and surface mesh with standard tools such that the surface grid is always induced by the volume grid. We describe the concepts behind this approach for bisectional refinement and describe new tools incorporated in the finite element toolbox ALBERTA. We also present several important applications of the mesh coupling.

  4. Prices Up and Volumes Stable

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    2011 First Half China Garment Industry Report Exports Grew at a Slower Pace China Customs reported the garment & accessories export value of $51.286 billion for the first five months of this year, up 23.12% y/y, accounting for 56.28 percent of the total, 5% lower than the previous year’s points.Despite sales prices increase, sales volume remain stable. From Jan. to May

  5. Analytic torsion and symplectic volume

    DEFF Research Database (Denmark)

    McLellan, Brendan Donald Kenneth

    2013-01-01

    This article studies the abelian analytic torsion on a closed, oriented, quasi-regular Sasakian three-manifold and identifies this quantity as a specific multiple of the natural unit symplectic volume form on the moduli space of flat abelian connections. This identification effectively computes...... the analytic torsion explicitly in terms of Seifert data for a given quasi-regular Sasakian structure on a three-manifold....

  6. Memorial volume for Y. Nambu

    CERN Document Server

    Chang, Lay Nam; Han, Moo-Young; Phua, Kok Khoo

    2016-01-01

    We have lost one of the giants of the twentieth century physics when Yoichiro Nambu passed away in July, 2015, at the age of 94. Today's Standard Model, though still incomplete in many respects, is the culmination of the most successful theory of the Universe to date, and it is built upon foundations provided by discoveries made by Nambu in the 1960s: the mechanism of spontaneously broken symmetry in Nature (with G Jona-Lasinio) and the hidden new SU(3) symmetry of quarks and gluons (with M-Y Han). In this volume honoring Nambu's memory, World Scientific Publishing presents a unique collection of papers written by his former colleagues, collaborating researchers and former students and associates, not only citing Nambu's great contributions in physics but also many personal and private reminiscences, some never told before. This volume also contains the very last scientific writing by Professor Nambu himself, discussing the development of particle physics. This book is a volume for all who benefited not on...

  7. Cell volume regulation: physiology and pathophysiology

    DEFF Research Database (Denmark)

    Lambert, I H; Hoffmann, E K; Pedersen, Stine Helene Falsig

    2008-01-01

    Cell volume perturbation initiates a wide array of intracellular signalling cascades, leading to protective and adaptive events and, in most cases, activation of volume-regulatory osmolyte transport, water loss, and hence restoration of cell volume and cellular function. Cell volume is challenged....../hypernatremia. On the other hand, it has recently become clear that an increase or reduction in cell volume can also serve as a specific signal in the regulation of physiological processes such as transepithelial transport, cell migration, proliferation and death. Although the mechanisms by which cell volume perturbations...

  8. Singularity Theory and its Applications

    CERN Document Server

    Stewart, Ian; Mond, David; Montaldi, James

    1991-01-01

    A workshop on Singularities, Bifuraction and Dynamics was held at Warwick in July 1989, as part of a year-long symposium on Singularity Theory and its applications. The proceedings fall into two halves: Volume I mainly on connections with algebraic geometry and volume II on connections with dynamical systems theory, bifurcation theory and applications in the sciences. The papers are original research, stimulated by the symposium and workshop: All have been refereed and none will appear elsewhere. The main topic of volume II is new methods for the study of bifurcations in nonlinear dynamical systems, and applications of these.

  9. Calculation of the Residual Blood Volume after Acute, Non-Ongoing Hemorrhage Using Serial Hematocrit Measurements and the Volume of Isotonic Fluid Infused: Theoretical Hypothesis Generating Study.

    Science.gov (United States)

    Oh, Won Sup; Chon, Sung-Bin

    2016-05-01

    Fluid resuscitation, hemostasis, and transfusion is essential in care of hemorrhagic shock. Although estimation of the residual blood volume is crucial, the standard measuring methods are impractical or unsafe. Vital signs, central venous or pulmonary artery pressures are inaccurate. We hypothesized that the residual blood volume for acute, non-ongoing hemorrhage was calculable using serial hematocrit measurements and the volume of isotonic solution infused. Blood volume is the sum of volumes of red blood cells and plasma. For acute, non-ongoing hemorrhage, red blood cell volume would not change. A certain portion of the isotonic fluid would increase plasma volume. Mathematically, we suggest that the residual blood volume after acute, non-ongoing hemorrhage might be calculated as 0·25N/[(Hct1/Hct2)-1], where Hct1 and Hct2 are the initial and subsequent hematocrits, respectively, and N is the volume of isotonic solution infused. In vivo validation and modification is needed before clinical application of this model.

  10. International Linear Collider Technical Design Report (Volumes 1 through 4)

    Energy Technology Data Exchange (ETDEWEB)

    Harrison M.

    2013-03-27

    The design report consists of four volumes: Volume 1, Executive Summary; Volume 2, Physics; Volume 3, Accelerator (Part I, R and D in the Technical Design Phase, and Part II, Baseline Design); and Volume 4, Detectors.

  11. Effects of immersion on visual analysis of volume data.

    Science.gov (United States)

    Laha, Bireswar; Sensharma, Kriti; Schiffbauer, James D; Bowman, Doug A

    2012-04-01

    Volume visualization has been widely used for decades for analyzing datasets ranging from 3D medical images to seismic data to paleontological data. Many have proposed using immersive virtual reality (VR) systems to view volume visualizations, and there is anecdotal evidence of the benefits of VR for this purpose. However, there has been very little empirical research exploring the effects of higher levels of immersion for volume visualization, and it is not known how various components of immersion influence the effectiveness of visualization in VR. We conducted a controlled experiment in which we studied the independent and combined effects of three components of immersion (head tracking, field of regard, and stereoscopic rendering) on the effectiveness of visualization tasks with two x-ray microscopic computed tomography datasets. We report significant benefits of analyzing volume data in an environment involving those components of immersion. We find that the benefits do not necessarily require all three components simultaneously, and that the components have variable influence on different task categories. The results of our study improve our understanding of the effects of immersion on perceived and actual task performance, and provide guidance on the choice of display systems to designers seeking to maximize the effectiveness of volume visualization applications. PMID:22402687

  12. Site Environmental Report for 2005 Volume I and Volume II

    Energy Technology Data Exchange (ETDEWEB)

    Ruggieri, Michael

    2006-07-07

    Each year, Ernest Orlando Lawrence Berkeley National Laboratory prepares an integrated report on its environmental programs to satisfy the requirements of United States Department of Energy Order 231.1A, ''Environment, Safety, and Health Reporting''. The ''Site Environmental Report for 2005'' summarizes Berkeley Lab's environmental management performance, presents environmental monitoring results, and describes significant programs for calendar year 2005. (Throughout this report, Ernest Orlando Lawrence Berkeley National Laboratory is referred to as ''Berkeley Lab'', ''the Laboratory'', ''Lawrence Berkeley National Laboratory'', and ''LBNL''.) The report is separated into two volumes. Volume I contains an overview of the Laboratory, the status of environmental programs, and summarized results from surveillance and monitoring activities. This year's Volume I text body is organized into an executive summary followed by six chapters. The report's structure has been reorganized this year, and it now includes a chapter devoted to environmental management system topics. Volume II contains individual data results from surveillance and monitoring activities. The ''Site Environmental Report'' is distributed by releasing it on the Web from the Berkeley Lab Environmental Services Group (ESG) home page, which is located at http://www.lbl.gov/ehs/esg/. Many of the documents cited in this report also are accessible from the ESG Web page. CD and printed copies of this Site Environmental Report are available upon request. The report follows the Laboratory's policy of using the International System of Units (SI), also known as the metric system of measurements. Whenever possible, results are also reported using the more conventional (non-SI) system of measurements, because the non-SI system is referenced by several current

  13. Evaluation of standard liver volume formulae for Chinese adults

    Institute of Scientific and Technical Information of China (English)

    Zheng-Rong Shi; Lu-Nan Yan; Bo Li; Tian-Fu Wen

    2009-01-01

    AIM:To evaluate different standard liver volume (SLV) formula and verify the applicability of the formulae for Chinese adults.METHODS:Data from 70 cases of living donor liver transplantation (LDLT) performed at our transplantation centers between January 2008 and April 2009 were analyzed.SLV was estimated using our recently reported formula [the Chengdu formula:SLV (mL) = 11.5×body weight (kg) + 334] and other reported formulae used for Chinese adults.Actual intraoperative liver volumes were obtained from a review of the patients' medical records.RESULTS:The actual right liver volume was not signifi-cantly different from the estimated right liver volume determined by the Chengdu formula,but was significantly smaller than estimates using the Heinemann,Urata,Vauthey,and Lee formulae (P<0.01),and significantly larger than estimates using the Fan formula (P<0.05).CONCLUSION:The Chengdu formula was demonstrated to be reliable by its application in LDLT.

  14. 探讨应用被动抬腿试验联合中心静脉压预测老年脓毒症患者的容量反应性%To Explore the Application of Passive Leg Raising Combined With Central Venous Pressure Predict Volume Responsiveness in Elderly Patients With Sepsis

    Institute of Scientific and Technical Information of China (English)

    农忻月

    2016-01-01

    目的:研究分析应用被动抬腿试验联合中心静脉压预测老年脓毒症患者的容量反应性。方法选取2015年10月~2016年3月我院收治的老年脓毒症患者40例,通过容量负荷试验后每搏量的增加值情况分为观察组与对照组。结果观察组患者扩容后心率低于对照组患者,差异具有统计学意义(P<0.05)。观察组患者扩容后动脉压、每搏量、心输出量以及氧合指数均高于对照组患者,差异具有统计学意义(P<0.05)。结论观察组患者扩容后心输出量增加,而中心静脉压降低,所以应用被动抬腿试验联合中心静脉压能有效预测老年脓毒症患者的容量反应性。%Objective To study the analysis application of passive leg joint central venous pressure prediction capacity reactivity in elderly patients with sepsis. Methods 40 patients with sepsis were select from October 2015 to March 2016 in our hospital, through the capacity load experiment after stroke volume of added value is divided into observation group and control group.Results Observation group of patients with enlarged heart rate was signiifcantly lower than the control group patients, difference is statistically signiifcant (P<0.05). Observation group of patients expansion after arterial pressure, stroke volume, cardiac output and oxygenation index were signiifcantly higher than that of control group patients, difference is statistically signiifcant (P<0.05).Conclusion To observe the way patients expansion increased markedly, and the middle of the back the output and central venous pressure has a significant decrease, so the application of combined central venous pressure passive leg lifts test can effectively predict the capacity of the elderly patients with sepsis reactivity.

  15. Oak Ridge K-25 Site Technology Logic Diagram. Volume 2, Technology Logic Diagrams

    Energy Technology Data Exchange (ETDEWEB)

    Fellows, R.L. [ed.

    1993-02-26

    The Oak Ridge K-25 Technology Logic Diagram (TLD), a decision support tool for the K-25 Site, was developed to provide a planning document that relates envirorunental restoration and waste management problems at the Oak Ridge K-25 Site to potential technologies that can remediate these problems. The TLD technique identifies the research necessary to develop these technologies to a state that allows for technology transfer and application to waste management, remedial action, and decontamination and decommissioning activities. The TLD consists of four separate volumes-Vol. 1, Vol. 2, Vol. 3A, and Vol. 3B. Volume 1 provides introductory and overview information about the TLD. This volume, Volume 2, contains logic diagrams with an index. Volume 3 has been divided into two separate volumes to facilitate handling and use.

  16. American power conference: Proceedings. Volume 56-I

    International Nuclear Information System (INIS)

    The first volume of this conference contains papers on the following topics: (1) Controls, monitoring, and expert systems (Harnessing microprocessor revolution for a more competitive power industry; Plant control--Upgrades; Neural network applications); (2) Diversification and globalization (Electric utility diversification/globalization--Panel; Private power in developing countries); (3) Environment and clean air (Clean Air compliance costs; Site selection for power stations and related facilities; Electric utility trace substance emissions; Solid waste disposal and commercial use; Precipitators/fabric filters; and Effect of flow modifications on fisheries and water quality); (4) Generation--Fuel options ampersand equipment (Alternate fuels; Advances in fuel cells for electric power applications; Secondary containment and seismic requirements for petrochemical facilities; Clean coal technology demonstration; Advanced energy systems; Hydropower); (5) Nuclear operations ampersand options (Radioactive waste management and disposal; Off normal conditions; Advanced light water reactors--15 years after TMI; Structural dynamic analyses for nuclear power plants); (6) Retrofit, betterment, repowering ampersand maintenance (Project management; Improving competitiveness through process re-engineering; Central stations; Water and wastewater treatment); (7) System planning, operation ampersand demand maintenance (Transmission system access; Stability; Systems planning); (8) Transmission and distribution (Transformers; Relaying for system protection; Managing EMF effects); and (9) Education (Power engineering). 155 papers have been processed separately for inclusion on the data base

  17. RADTRAN 4: User guide. Volume 3

    Energy Technology Data Exchange (ETDEWEB)

    Neuhauser, K S [Sandia National Labs., Albuquerque, NM (United States); Kanipe, F L [GRAM, Inc., Albuquerque, NM (United States)

    1992-01-01

    RADTRAN 4 is used to evaluate radiological consequences of incident-free transportation, as well as the radiological risks from vehicular accidents occurring during transportation. This User Guide is Volume 3 in a series of four volume of the documentation of the RADTRAN 4 computer code for transportation risk analysis. The other three volumes are Volume 1, the Executive Summary; Volume 2, the Technical Manual; and Volume 4, the Programmer`s Manual. The theoretical and calculational basis for the operations performed by RADTRAN 4 are discussed in Volume 2. Throughout this User Guide the reader will be referred to Volume 2 for detailed discussions of certain RADTRAN features. This User Guide supersedes the document ``RADTRAN III`` by Madsen et al. (1983). This RADTRAN 4 User Guide specifies and describes the required data, control inputs, input sequences, user options, program limitations, and other activities necessary for execution of the RADTRAN 4 computer code.

  18. Oncoplastic breast conserving surgery: Volume replacement vs. volume displacement.

    Science.gov (United States)

    Noguchi, M; Yokoi-Noguchi, M; Ohno, Y; Morioka, E; Nakano, Y; Kosaka, T; Kurita, T

    2016-07-01

    Oncoplastic breast conserving surgery (BCS) has emerged as a third option between conventional BCS and mastectomy. Oncoplastic BCS includes two fundamentally different approaches: volume replacement and volume displacement. The former involves partial mastectomy and immediate reconstruction of the breast with the transposition of autologous tissue from elsewhere, while the latter involves partial mastectomy and using the remaining breast tissue to fill the defect resulting from extirpation of the tumor. There are several benefits associated with oncoplastic BCS. First, it allows partial mastectomy without cosmetic penalties, and can achieve better cosmetic outcomes than total mastectomy with immediate breast reconstruction. Second, it avoids the need for total mastectomy in an increasing number of patients without compromising local control. Third, partial breast reconstruction is less extensive and has fewer complications than conventional procedures. Partial mastectomy and partial breast reconstruction can be carried out either simultaneously as a one-stage procedure, or using a two-stage approach. Although patients prefer a one-stage procedure, it requires intraoperative confirmation of complete tumor excision using frozen-section analysis. Moreover, oncoplastic BCS requires combined skills, knowledge, and understanding of both oncological and plastic surgeries, which may be optimally achieved by an oncoplastic surgeon. PMID:26988623

  19. Do distribution volumes and clearances relate to tissue volumes and blood flows? A computer simulation

    Directory of Open Access Journals (Sweden)

    Lemmens Hendrikus JM

    2006-06-01

    , concepts that are traditionally thought of as being applicable to the kinetics of intravenous agents can be equally well applied to anesthetic gases. Distribution volumes and clearances cannot be equated to tissue volumes and blood flows respectively.

  20. Applications of combinatorial optimization

    CERN Document Server

    Paschos, Vangelis Th

    2013-01-01

    Combinatorial optimization is a multidisciplinary scientific area, lying in the interface of three major scientific domains: mathematics, theoretical computer science and management. The three volumes of the Combinatorial Optimization series aims to cover a wide range of topics in this area. These topics also deal with fundamental notions and approaches as with several classical applications of combinatorial optimization. "Applications of Combinatorial Optimization" is presenting a certain number among the most common and well-known applications of Combinatorial Optimization.

  1. Functional renormalisation group in a finite volume

    OpenAIRE

    Fister, Leonard; Pawlowski, Jan Martin

    2015-01-01

    We study a $\\phi^4$-theory at finite temperature in a finite volume. Quantum, thermal and volume fluctuations are treated with the functional renormalisation group. Specifically, we focus on the interplay of temperature and length scales driving the system. We find that thermodynamical observables at finite volume such as the pressure approach the infinite volume limit similarly to that of the vanishing temperature limit. We also advance the functional renormalisation group method at finite v...

  2. Finite volume hydromechanical simulation in porous media

    OpenAIRE

    Nordbotten, Jan Martin

    2014-01-01

    Cell-centered finite volume methods are prevailing in numerical simulation of flow in porous media. However, due to the lack of cell-centered finite volume methods for mechanics, coupled flow and deformation is usually treated either by coupled finite-volume-finite element discretizations, or within a finite element setting. The former approach is unfavorable as it introduces two separate grid structures, while the latter approach loses the advantages of finite volume methods for the flow equ...

  3. Computational stress analysis using finite volume methods

    OpenAIRE

    Fallah, Nosrat Allah

    2000-01-01

    There is a growing interest in applying finite volume methods to model solid mechanics problems and multi-physics phenomena. During the last ten years an increasing amount of activity has taken place in this area. Unlike the finite element formulation, which generally involves volume integrals, the finite volume formulation transfers volume integrals to surface integrals using the divergence theorem. This transformation for convection and diffusion terms in the governing equations, ensures...

  4. The parallel volume at large distances

    DEFF Research Database (Denmark)

    Kampf, Jürgen

    In this paper we examine the asymptotic behavior of the parallel volume of planar non-convex bodies as the distance tends to infinity. We show that the difference between the parallel volume of the convex hull of a body and the parallel volume of the body itself tends to . This yields a new proof...... for the fact that a planar body can only have polynomial parallel volume, if it is convex. Extensions to Minkowski spaces and random sets are also discussed....

  5. The parallel volume at large distances

    DEFF Research Database (Denmark)

    Kampf, Jürgen

    In this paper we examine the asymptotic behavior of the parallel volume of planar non-convex bodies as the distance tends to infinity. We show that the difference between the parallel volume of the convex hull of a body and the parallel volume of the body itself tends to 0. This yields a new proof...... for the fact that a planar body can only have polynomial parallel volume, if it is convex. Extensions to Minkowski spaces and random sets are also discussed....

  6. On the volume of cremated remains

    DEFF Research Database (Denmark)

    Harvig, Lise Lock; Lynnerup, Niels

    2013-01-01

    Harvig, L., Lynnerup, N. 2013. On the effective volume of prehistoric cremains - a comparative study of cremated bone volume measured manually and assessed by Computed Tomography. Journal of Archaeological Science 40, p. 2713–2722.......Harvig, L., Lynnerup, N. 2013. On the effective volume of prehistoric cremains - a comparative study of cremated bone volume measured manually and assessed by Computed Tomography. Journal of Archaeological Science 40, p. 2713–2722....

  7. Apparatus Translates Crossed-Laser-Beam Probe Volume

    Science.gov (United States)

    Herring, Gregory C.; South, Bruce W.; Exton, Reginald J.

    1994-01-01

    Optomechanical apparatus translates probe volume of crossed-beam laser velocimeter or similar instrument while maintaining optical alignment of beams. Measures velocity, pressure, and temperature of flowing gas at several locations. Repeated tedious realignments no longer necessary. Designed to accommodate stimulated-Raman-gain spectrometer for noninvasive measurement of local conditions in flowing gas in supersonic wind tunnel. Applicable to other techniques like coherent anti-Stokes Raman spectroscopy involving use of laser beams crossed at small angles (10 degrees or less).

  8. Analysis of airborne radiometric data. Volume 3. Topical reports

    International Nuclear Information System (INIS)

    This volume consists of four topical reports: a general discussion of the philosophy of unfolding spectra with continuum and discrete components, a mathematical treatment of the effects of various physical parameters on the uncollided gamma-ray spectrum at aircraft elevations, a discussion of the application of the unfolding code MAZNAI to airborne data, and a discussion of the effects of the nonlinear relationship between energy deposited and pulse height in NaI(T1) detectors

  9. Environmental Report 1995. Volume 1

    International Nuclear Information System (INIS)

    This report contains the results of Lawrence Livermore National Laboratory's (LLNL) environmental monitoring and compliance effort and an assessment of the impact of LLNL operations on the environment and the public. This first volume describes LLNL's environmental impact and compliance activities and features descriptive and explanatory text, summary data tables, and plots showing data trends. The summary data include measures of the center of data, their spread or variability, and their extreme values. Chapters on monitoring air, sewage, surface water, ground water, soil and sediment, vegetation and foodstuff, and environmental radiation are present

  10. Environmental Report 1995. Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Harrach, R.J.; Failor, R.A.; Gallegos, G.M. [and others

    1996-09-01

    This report contains the results of Lawrence Livermore National Laboratory`s (LLNL) environmental monitoring and compliance effort and an assessment of the impact of LLNL operations on the environment and the public. This first volume describes LLNL`s environmental impact and compliance activities and features descriptive and explanatory text, summary data tables, and plots showing data trends. The summary data include measures of the center of data, their spread or variability, and their extreme values. Chapters on monitoring air, sewage, surface water, ground water, soil and sediment, vegetation and foodstuff, and environmental radiation are present.

  11. Spectrum '86: Proceedings: Volume 1

    International Nuclear Information System (INIS)

    This document, Volume 1 of two, contains 100 papers on various aspects of Radioactive Waste Management. Session topics include: nuclear success stories; low-level waste-grout; filtration and ion exchange, qualification, and pretreatment; solid waste treatment/endash/special grouts, and incineration; equipment design/endash/remote technology, and special equipment; high-level waste/endash/international vitrification projects, plans and system testing, product performance, meltor and product testing, off-gas behavior and processing. Individual reports were processed separately for the data bases

  12. Comparing Volumes of Prisms and Pyramids

    Science.gov (United States)

    Vinogradova, Natalya

    2012-01-01

    Students' experience in using formulas for volumes is often limited to substituting numbers into given formulas. An activity presented in this article may help students make connections between the formulas for volumes of prisms and volumes of pyramids. In addition, some interesting facts from number theory arise, demonstrating strong connections…

  13. Culture of Schools. Final Report. Volume IV.

    Science.gov (United States)

    American Anthropological Association, Washington, DC.

    The final volume of this 4-volume report contains further selections from "Anthropological Perspectives on Education," a monograph to be published by Basic Books of New York. (Other selections are in Vol. III, SP 003 902.) Monograph selections appearing in this volume are: "Great Tradition, Little Tradition, and Formal Education;""Indians,…

  14. Photorefractive Materials and Their Applications 2 Materials

    CERN Document Server

    Günter, Peter

    2007-01-01

    Photorefractive Materials and Their Applications 2: Materials is the second of three volumes within the Springer Series in Optical Sciences. The book gives a comprehensive review of the most important photorefractive materials and discusses the physical properties of organic and inorganic crystals as well as poled polymers. In this volume, photorefractive effects have been investigated at wavelengths covering the UV, visible and near infrared. Researchers in the field and graduate students of solid-state physics and engineering will gain a thorough understanding of the properties of materials in photorefractive applications. The other two volumes are: Photorefractive Materials and Their Applications 1: Basic Effects. Photorefractive Materials and Their Applications 3: Applications.

  15. 自动化容积成像技术在中晚孕期正常胎儿心脏超声检查中的应用%Volume computer aided diagnosis technology in the middle-late application of normal fetal cardiac ultrasound during pregnancy

    Institute of Scientific and Technical Information of China (English)

    薛前海; 王胜华

    2014-01-01

    Objective To explore the application of volume computer aided diagnosis technology in the middle-late application of normal fetal cardiac ultrasound during pregnancy. Method Retrospective analysis of 87 cases of antenatal examination of pregnant women in our hospital obstetrics and gynecology fetal echocardiogram results. Result VCAD inspection time were shorter than 2D and STIC-TUI examination time, VCAD to automatically cut and the gain of 2Dplane there was no signiifcant difference between the percent of pass (χ2=0.87, P>0.05). Conclusion VCAD is a good choice for fetal cardiac ultrasound, it can quickly obtain the fetus cardiac screening various aspects of information, and can ensure the quality of image.%目的:对自动化容积成像(VCAD)在中晚孕期正常胎儿心脏超声检查中的应用进行探讨。方法回顾性分析87例在本院进行产前检查孕妇的胎儿心脏超声结果。结果 VCAD检查时间均比二维超声及时空关联成像-超声断层显像(STIC-TUI)检查时间短,VCAD自动获取切面与二维超声获得切面的合格率之间无显著差异(χ2=0.87,P>0.05)。结论 VCAD可以较快地获取胎儿心脏筛查各切面的信息,且可以保证图像质量,是胎儿心脏超声检查的较好选择。

  16. Dose and volume specification for reporting interstitial therapy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-30

    The ICRU has previously published reports dealing with Dose Specification for Reporting External Beam Therapy with Photons and Electrons (ICRU Report 29, ICRU, 1978), Dose Specification for Reporting External Beam Therapy (ICRU Report 50, ICRU, 1993) and Dose and Volume Specification for Reporting Intracavitary Therapy in Gynecology (ICRU Report 38, ICRU, 1985). The present report addresses the problem of absorbed dose specification for report interstitial therapy. Although specific to interstitial therapy, many of the concepts developed in this report are also applicable to certain other kinds of brachytherapy applications. In particular, special cases of intraluminal brachytherapy and plesio-brachytherapy via surface molds employing x or gamma emitters are addressed in this report.

  17. The detection and subsequent volume optimization of biological nanocrystals

    Directory of Open Access Journals (Sweden)

    Joseph R. Luft

    2015-07-01

    Full Text Available Identifying and then optimizing initial crystallization conditions is a prerequisite for macromolecular structure determination by crystallography. Improved technologies enable data collection on crystals that are difficult if not impossible to detect using visible imaging. The application of second-order nonlinear imaging of chiral crystals and ultraviolet two-photon excited fluorescence detection is shown to be applicable in a high-throughput manner to rapidly verify the presence of nanocrystals in crystallization screening conditions. It is noted that the nanocrystals are rarely seen without also producing microcrystals from other chemical conditions. A crystal volume optimization method is described and associated with a phase diagram for crystallization.

  18. Dose and volume specification for reporting interstitial therapy

    International Nuclear Information System (INIS)

    The ICRU has previously published reports dealing with Dose Specification for Reporting External Beam Therapy with Photons and Electrons (ICRU Report 29, ICRU, 1978), Dose Specification for Reporting External Beam Therapy (ICRU Report 50, ICRU, 1993) and Dose and Volume Specification for Reporting Intracavitary Therapy in Gynecology (ICRU Report 38, ICRU, 1985). The present report addresses the problem of absorbed dose specification for report interstitial therapy. Although specific to interstitial therapy, many of the concepts developed in this report are also applicable to certain other kinds of brachytherapy applications. In particular, special cases of intraluminal brachytherapy and plesio-brachytherapy via surface molds employing x or gamma emitters are addressed in this report

  19. Waste isolation safeguards and security system. Volume 1. Scoping study

    International Nuclear Information System (INIS)

    The purpose of this study is to define the rationale and scope of the Waste Isolation System (WIS) safeguards system, to establish a set of proposed basic safeguards criteria, and to identify the areas requiring development of specific criteria and technology. The report also presents a proposed program schedule and provides an extensive bibliography of applicable reference safeguards documents. Volume one contains the following: glossary, system description; threat definition; safeguards regulations review - current and future; WIS safeguards criteria; assessment of criteria applicability and development requirements; and program plan

  20. LLE Review. Quarterly report, January--March 1992: Volume 50

    Energy Technology Data Exchange (ETDEWEB)

    Keck, R.L. [ed.

    1992-09-01

    This volume of the LLE Review, covering the period January--March 1992, contains articles on the use of diffraction gratings in laser applications, and the fabrication of gratings for use in these applications. there are two articles on the use of lasers to explore fundamental physics issues and an article on the use of a solid-state diode array for x-ray imaging. Finally, the activities of the National Laser Users Facility and the GDL and OMEGA laser systems are summarized.