WorldWideScience

Sample records for antimony complexes

  1. Mixed Antimony(V Complexes with Different Sugars to Modulate the Oral Bioavailability of Pentavalent Antimonial Drugs

    Directory of Open Access Journals (Sweden)

    Weverson A. Ferreira

    2014-04-01

    Full Text Available Previous studies have shown that the association of the drug meglumine antimoniate (MA with β-cyclodextrin can improve its bioavailability by the oral route. In this work, ribose and maltose were investigated for their ability to form mixed or association complexes with MA, release MA and modulate the serum levels of Sb after oral administration in mice. Analysis of the MA/ribose composition by high performance liquid chromatography coupled to mass spectrometry (LCMS-IT-TOF revealed the presence of mixed meglumine-Sb-ribose and Sb-ribose complexes. Analysis of the MA/maltose composition suggested the formation of MA-maltose association compounds. Circular dichroism characterization of these compositions following dilution in water at 37 °C suggested a partial and slow dissociation of the association compounds. When the MA/ribose composition was administered orally and compared to MA, the serum concentration of Sb was significantly lower after 1 h and greater after 3 h. On the other hand, the MA/maltose composition showed similar serum Sb concentration after 1 h and higher level of Sb after 3 h, when compared to MA. In conclusion, the present study has demonstrated the formation of mixed or association complexes of MA with sugars, such as maltose and ribose, which promoted sustained serum level of Sb after oral administration.

  2. The MRP1-mediated effluxes of arsenic and antimony do not require arsenic-glutathione and antimony-glutathione complex formation.

    Science.gov (United States)

    Salerno, Milena; Petroutsa, Maria; Garnier-Suillerot, Arlette

    2002-04-01

    Arsenic trioxide is an effective treatment for acute promyelocytic leukemia, but resistance to metalloid salts is found in humans. Using atomic absorption spectroscopy, we have measured the rate of uptake of arsenic trioxide and of antimony tartrate in GLC4 and GLC4/ADR cells overexpressing MRP1 and the rate of their MRP1-mediated effluxes as a function of the intracellular GSH concentration. In sensitive cells, after 1 h, a pseudosteady state is reached where intra- and extracellular concentrations of metalloid are the same. This precludes the formation, at short term, of complexes between arsenic or antimony with GSH. In resistant cells reduced intracellular accumulation of arsenic (or antimony), reflecting an increased rate of arsenic (or antimony) efflux from the cells, is observed. No efflux of the metalloid is observed in GSH depleted cells. The two metalloids and GSH are pumped out by MRP1 with the same efficiency. Moreover for the three compounds 50% of the efflux is inhibited by 2 microM MK571. This led us to suggest that As- and Sb-containing species could be cotransported with GSH. PMID:12018890

  3. Organically complexed iron enhances bioavailability of antimony to maize (Zea mays) seedlings in organic soils.

    Science.gov (United States)

    Ptak, Corey; McBride, Murray

    2015-12-01

    Antimony (Sb) is a metalloid belonging to group 15 of the periodic table. Chemical similarities between arsenic (As) and Sb produce concerns about potential health effects of Sb and enrichment in the environment. Antimony is found in oxic environments predominately as an oxyanionic species, antimonite (Sb[OH](6-)). As a result of its net negative charge, Sb[OH](6-) was not initially predicted to have strong interactions with natural organic matter. Oxyanionic species could bind the negatively charged organic matter via a ternary complexation mechanism, in which cationic metals mediate the strong association between organic matter functional groups and oxyanions. However, these interactions are poorly understood in how they influence the bioavailability of oxyanionic contaminants to plants. Iron (Fe) additions to organic soils have been found to increase the number of organically complexed Fe sites suitable for Sb exchange, resulting in a reduced bioavailable fraction of Sb. The bioavailability of Sb to maize seedlings as a function of organically complexed Fe was examined using a greenhouse study. A significant increase in plant tissue Sb was observed as organically complexed Fe increased, which was not predicted by methods commonly used to assess bioavailable Sb. Extraction of soils with organic acids common to the maize rhizosphere suggested that organic acid exudation can readily mobilize Sb bound by organic Fe complexes. PMID:26076768

  4. Organically complexed iron enhances bioavailability of antimony to maize (Zea mays) seedlings in organic soils.

    Science.gov (United States)

    Ptak, Corey; McBride, Murray

    2015-12-01

    Antimony (Sb) is a metalloid belonging to group 15 of the periodic table. Chemical similarities between arsenic (As) and Sb produce concerns about potential health effects of Sb and enrichment in the environment. Antimony is found in oxic environments predominately as an oxyanionic species, antimonite (Sb[OH](6-)). As a result of its net negative charge, Sb[OH](6-) was not initially predicted to have strong interactions with natural organic matter. Oxyanionic species could bind the negatively charged organic matter via a ternary complexation mechanism, in which cationic metals mediate the strong association between organic matter functional groups and oxyanions. However, these interactions are poorly understood in how they influence the bioavailability of oxyanionic contaminants to plants. Iron (Fe) additions to organic soils have been found to increase the number of organically complexed Fe sites suitable for Sb exchange, resulting in a reduced bioavailable fraction of Sb. The bioavailability of Sb to maize seedlings as a function of organically complexed Fe was examined using a greenhouse study. A significant increase in plant tissue Sb was observed as organically complexed Fe increased, which was not predicted by methods commonly used to assess bioavailable Sb. Extraction of soils with organic acids common to the maize rhizosphere suggested that organic acid exudation can readily mobilize Sb bound by organic Fe complexes.

  5. Nuclear quadrupole resonance of iodine pentafluoride and its complexes with antimony pentafluoride

    International Nuclear Information System (INIS)

    The spectra of nuclear quadrupole resonance (NQR) have been obtained at 77 deg K for I127 and Sbsup(121,128) in the IF5, IF5xSbF5, IF5x2SbF5, CsIF6, and RbIF6 compounds. An agreement between quadrupole spectra and structural data have been observed. The results of studying IF5 by NQR, gamma resonance and microwave spectroscopy have been compared. It has been established that unshared electron pair of an iodine atom is stereochemically active which leads to a considerable distortion of octahedral symmetry of coordination polyhedron of the iodine atoms. The structure of complexes of iodine pentafluoride with antimony pentafluoride is given

  6. Spin dynamics of complex oxides, bismuth-antimony alloys, and bismuth chalcogenides

    Science.gov (United States)

    Sahin, Cuneyt

    The emerging field of spintronics relies on the manipulation of electron spin in order to use it in spin-based electronics. Such a paradigm change has to tackle several challenges including finding materials with sufficiently long spin lifetimes and materials which are efficient in generating pure spin currents. This thesis predicts that two types of material families could be a solution to the aforementioned challenges: complex oxides and bismuth based materials. We derived a general approach for constructing an effective spin-orbit Hamiltonian which is applicable to all nonmagnetic materials. This formalism is useful for calculating spin-dependent properties near an arbitrary point in momentum space. We also verified this formalism through comparisons with other approaches for III-V semiconductors, and its general applicability is illustrated by deriving the spin-orbit interaction and predicting spin lifetimes for strained strontium titanate (STO) and a two-dimensional electron gas in STO (such as at the LAO/STO interface). Our results suggest robust spin coherence and spin transport properties in STO related materials even at room temperature. In the second part of the study we calculated intrinsic spin Hall conductivities for bismuth-antimony (BISb) semimetals with strong spin-orbit couplings, from the Kubo formula and using Berry curvatures evaluated throughout the Brillouin zone from a tight-binding Hamiltonian. Nearly crossing bands with strong spin-orbit interaction generate giant spin Hall conductivities in these materials, ranging from 474 ((h/e)O--1cm--1) for bismuth to 96((h/e)O--1cm --1) for antimony; the value for bismuth is more than twice that of platinum. The large spin Hall conductivities persist for alloy compositions corresponding to a three-dimensional topological insulator state, such as Bi0.83Sb0.17. The spin Hall conductivity could be changed by a factor of 5 for doped Bi, or for Bi0.83Sb0.17, by changing the chemical potential by 0.5 e

  7. Antimony Toxicity

    Directory of Open Access Journals (Sweden)

    Shyam Sundar

    2010-12-01

    Full Text Available Antimony toxicity occurs either due to occupational exposure or during therapy. Occupational exposure may cause respiratory irritation, pneumoconiosis, antimony spots on the skin and gastrointestinal symptoms. In addition antimony trioxide is possibly carcinogenic to humans. Improvements in working conditions have remarkably decreased the incidence of antimony toxicity in the workplace. As a therapeutic, antimony has been mostly used for the treatment of leishmaniasis and schistosomiasis. The major toxic side-effects of antimonials as a result of therapy are cardiotoxicity (~9% of patients and pancreatitis, which is seen commonly in HIV and visceral leishmaniasis co-infections. Quality control of each batch of drugs produced and regular monitoring for toxicity is required when antimonials are used therapeutically.

  8. Thermal decomposition of complex halides of arsenic(3), antimony(3) and bismuth(3) with alkali metals

    Energy Technology Data Exchange (ETDEWEB)

    Cyganski, A.; Ptaszynski, B.; Zalewicz, M. (Politechnika Lodzka (Poland))

    1980-01-01

    Thermal analyses of complexes M/sub 3/(As/sub 2/X/sub 9/) (M = Rb, Cs; X = Cl, Br), M/sub 3/(Sb/sub 2/X/sub 9/) (M = Rb, Cs; X = Cl, Br, I), Rb/sub 3/(BiX/sub 6/) (X = Cl, Br) and Cs/sub 3/(Bi/sub 2/X/sub 9/) (X = Cl, Br, I) were performed. From chemical and X-ray analyses of their solid decomposition products the mechanism of thermal decomposition reactions was established. From thermogravimetric curves apparent activation energies were calculated using Coats-Redfern's and Zsako's methods. Thermal stability of complexes increases distinctly in the following order: Ascomplexes are more stabile than rubidium compounds of the same type.

  9. Complexing of antimony(3) fluoride with rare alkali metal fluorides in formic acid

    International Nuclear Information System (INIS)

    Using the method of isothermal solubility with the establishment of solid phase compositions according to ''residue method'' the systems HCOOH-SbF3-RbF3 and HCOOH-SbF3-CsF are studied at 15 deg C. The existence of complex compounds of different compositions is established. The individual character of the compounds prepared is confirmed by the data of chemical and X-ray phase analysis

  10. Structural and optical characterization of indium-antimony complexes in ZnO

    Energy Technology Data Exchange (ETDEWEB)

    Türker, M.; Deicher, M., E-mail: manfred.deicher@tech-phys.uni-sb.de; Johnston, K.; Wolf, H.; Wichert, Th. [Universität des Saarlandes, Experimentalphysik (Germany)

    2015-04-15

    One of the main obstacles to the technical application of the wide-gap semiconductor ZnO represents the difficulty to achieve reliable p-type doping of ZnO with group V elements (N, P, As, Sb) acting as acceptors located on O lattice sites. The theoretically proposed concepts of cluster-doping or codoping may lead to an enhanced and stable p-type conductivity of ZnO. We report on PAC results obtained by codoping experiments of ZnO by ion implantation using the donor {sup 111}In and the group-V acceptor Sb. The formation of In-Sb pairs has been observed. Based on these PAC results, there is no evidence for the formation of In-acceptor complexes involving more than one Sb acceptor. These results has been complemented by photoluminescence measurements.

  11. The determination of arsenic, selenium, antimony, and tin in complex environmental samples by hydride generation AAS

    International Nuclear Information System (INIS)

    Hydride generation techniques are used routinely for the determination of As, Se, Sb and Sn in water samples. Advantages include high sensitivity, simplicity, and relative freedom from interferences. Continuous-flow designs greatly reduce analysis time as well as improve precision and allow for automation. However the accurate analysis of more complex environmental samples such as industrial sludges, soil samples, river sediments, and fly ash remains difficult. Numerous contributing factors influence the accuracy of the hydride technique. Sample digestion methods and sample preparation procedures are of critical importance. The digestion must adequately solubilize the elements of interest without loss by volatilization. Sample preparation procedures that guarantee the proper analyte oxidation state and eliminate the nitric acid and inter-element interferences are needed. In this study, difficult environmental samples were analyzed for As, Se, Sb, and Sn by continuous flow hydride generation. Sample preparation methods were optimized to eliminate interferences. The results of spike recovery studies will be presented. Data from the analysis of the same samples by graphite furnace AAS will be presented for comparison of accuracy, precision, and analysis time

  12. New antimony(III) halide complexes with dithiocarbamate ligands derived from thiuram degradation: The effect of the molecule's close contacts on in vitro cytotoxic activity.

    Science.gov (United States)

    Urgut, O S; Ozturk, I I; Banti, C N; Kourkoumelis, N; Manoli, M; Tasiopoulos, A J; Hadjikakou, S K

    2016-01-01

    Antimony(III) halide complexes of the formulae {[SbBr(Me2DTC)2]n} (1), {[SbI(Me2DTC)2]n} (2) and {[(Me2DTC)2Sb(μ2-I)Sb(Me2DTC)2](+).I3(-)} (3) (Me2DTC = dimethyldithiocarbomate) were synthesized from SbX3, (X = Br or I) and tetramethylthiuram monosulfide (Me4tms) or tetramethylthiuram disulfide (Me4tds). The complexes were characterized by melting point (m.p.), elemental analysis (e.a.), Fourier-transform Infra-Red (FT-IR), Fourier-transform Raman (FT-Raman), Nuclear Magnetic Resonance ((1)H,(13)C-NMR) spectroscopy and Thermogravimetric-Differential Thermal Analysis (TG-DTA). Crystal structures of complexes 1-3 were determined with single crystal X-ray diffraction analysis. Complexes 1 and 2 are polymers with distorted square pyramidal (SP) geometry in each monomeric unit, whereas complex 3 is ionic, containing an iodonium linkage Sb-I(+)-Sb and an I3(-) counter anion; to the best of our knowledge, this is the first ionic antimony(III) iodide complex. The in vitro cytotoxic activity of 1-3 against human adenocarcinoma cells: breast (MCF-7) and cervix (HeLa) cells and non-cancerous cells: MRC-5 (normal human fetal lung fibroblast cells) was evaluated with trypan blue (TB) and sulforhodamine B (SRB) assays. Among antimony(III) compounds with sulfur containing ligand, those of dithiocarbamates exhibit significant cytotoxic activity. Hirshfeld surface volumes were analyzed to clarify the nature of the intermolecular interactions by the 2D fingerprint plot. Molecules with lower H-all atoms inter-molecular interactions exhibit the higher activity against MCF-7 cells. The in vivo genotoxicity of 1-3 was evaluated by the mean of Allium cepa test. Alterations in the mitotic index values due to the chromosomal aberrations were observed in the case of complexes 2 and 3. Since, no such alteration is caused by 1, it makes this compound candidate for further study as potential drug. PMID:26478326

  13. In Vitro antileishmanial properties of neutron-irradiated meglumine antimoniate

    OpenAIRE

    Samanta Etel Treiger Borborema; Heitor Franco de Andrade Junior; João Alberto Osso Junior; Nanci do Nascimento

    2005-01-01

    Pentavalent antimony, as meglumine antimoniate (Glucantime® ) or sodium stibogluconate (Pentostam® ), is the main treatment for leishmaniasis, a complex of diseases caused by the protozoan Leishmania, and an endemic and neglected threat in Brazil. Despite over half a century of clinical use, their mechanism of action, toxicity and pharmacokinetic data remain unknown. The analytical methods for determination of antimony in biological systems remain complex and have low sensitivity. Radiotracer...

  14. In vitro antileishmanial properties of neutron-irradiated meglumine antimoniate

    Energy Technology Data Exchange (ETDEWEB)

    Borborema, Samanta Etel Treiger; Nascimento, Nanci do [Instituto de Pesquisas Energeticas e Nucleares (IPEN-CNEN/SP), SP (Brazil). Lab. de Biologia Molecular]. E-mail: samanta@usp.br; Osso Junior, Joao Alberto [Instituto de Pesquisas Energeticas e Nucleares (IPEN-CNEN/SP), SP (Brazil). Centro de Radiofarmacia]. E-mail: jaosso@ipen.br; Andrade Junior, Heitor Franco de [Instituto de Medicina Tropical de Sao Paulo (IMT-SP), SP (Brazil). Lab. de Protozoologia]. E-mail:hfandrad@usp.br

    2005-10-15

    Pentavalent antimony, as meglumine antimoniate (Glucantime) or sodium stibogluconate (Pentostam), is the main treatment for leishmaniasis, a complex of diseases caused by the protozoan Leishmania, and an endemic and neglected threat in Brazil. Despite over half a century of clinical use, their mechanism of action, toxicity and pharmacokinetic data remain unknown. The analytical methods for determination of antimony in biological systems remain complex and have low sensitivity. Radiotracer studies have a potential in pharmaceutical development. The aim of this study was to obtain a radiotracer for antimony, with suitable physical and biological properties. Meglumine antimoniate was neutron irradiated inside the IEA-R1 nuclear reactor, producing two radioisotopes {sup 122} Sb and {sup 124} Sb, with high radionuclidic purity and good specific activity. This compound showed the same antileishmanial activity as the native compound. The use of the radiotracers, easily created by neutron irradiation, could be an interesting tool to solve important questions in antimonial pharmacology. (author)

  15. Improved Antileishmanial Activity of Dppz through Complexation with Antimony(III and Bismuth(III: Investigation of the Role of the Metal

    Directory of Open Access Journals (Sweden)

    Cynthia Demicheli

    2012-10-01

    Full Text Available Two novel trivalent antimony(III and bismuth(III complexes with the nitrogen-donor heterocyclic ligand dipyrido[3,2-a:2',3'-c]phenazine (dppz were synthesized and characterized as [Sb(dppzCl3]∙H2O∙CH3OH and [Bi(dppzCl3]. The crystal structure of Sb(III complex was determined by X-ray crystallography. These complexes were evaluated for their activity against the promastigote form of Sb(III-sensitive and –resistant Leishmania infantum chagasi and Leishmania amazonensis strains. Both complexes were more effective than dppz alone in inhibiting the growth of Leishmania promastigotes and were at least 77 and 2,400 times more active than potassium antimonyl tartrate in Sb(III-sensitive and -resistant Leishmania, respectively. The cytotoxicity of dppz and its complexes against mouse peritoneal macrophages occurred at dppz concentrations at least 6-fold greater than those found to be active against Leishmania promastigotes.To investigate the role of the metal in the improved antileishmanial activity of dppz, the activity of the Sb(III complex was compared between the Sb-resistant mutants and their respective parental sensitive strains. The lack of cross-resistance to the Sb(III-dppz complex together with the much lower activity of antimonyl tartrate, SbCl3 and BiCl3 strongly support the model that the metal is not active by itself but improves the activity of dppz through complexation.

  16. Perspectives of antimony compounds in oncology

    Institute of Scientific and Technical Information of China (English)

    Pankaj SHARMA; Diego PEREZ; Armando CABRERA; Nee ROSAS; Jose Luis ARIAS

    2008-01-01

    Antimony, a natural element that has been used as a drug for over more than 100 years, has remarkable therapeutic efficacy in patients with acute promyelocytic leukemia. This review focuses on recent advances in developing antimony anti- cancer agents with an emphasis on antimony coordination complexes, Sb (Ⅲ) and Sb (V). These complexes, which include many organometallic complexes, may provide a broader spectrum of antitumoral activity. They were compared with classical platinum anticancer drugs. The review covers the literature data pub- lished up to 2007. A number of antimonials with different antitumoral activities are known and have diverse applications, even though little research has been done on their possibilities. It might be feasible to develop more specific and effective inhibitors for phosphatase-targeted, anticancer therapeutics through the screen- ing of sodium stibogluconate (SSG) and potassium antimonyltartrate-related compounds, which are comprised of antimony conjugated to different organic moieties. For example, SSG appears to be a better inhibitor than suramin which is a compound known for its antineoplastic activity against several types of cancers.

  17. DNA cleavage, antimicrobial studies and a DFT-based QSAR study of new antimony(III) complexes as glutathione reductase inhibitor.

    Science.gov (United States)

    Tunç, Turgay; Koç, Yasemin; Açık, Leyla; Karacan, Mehmet Sayım; Karacan, Nurcan

    2015-02-01

    New antimony(III) complexes, [Sb(2-aminopyridine)2Cl3] (1a), [Sb(2-aminopyridine)2Br3] (1b), [Sb(5-methyl-2-aminopyridine)2Cl3] (2a), [Sb(5-methyl-2-aminopyridine)2Br3] (2b), [Sb(2-aminopyrimidine)2Cl3] (3a), [Sb(2-aminopyrimidine)2Br3] (3b), [Sb(4,6-dimethoxy-2-aminopyrimidine)2Cl3] (4a), [Sb(4,6-dimethoxy-2-aminopyrimidine)2Br3] (4b), [Sb(2-amino-1,3,5-triazine)2Cl3] (5a), [Sb(2-amino-1,3,5-triazine)2Br3] (5b), [Sb(2-guanidinobenzimidazole) Cl3] (6a), [Sb(2-guanidinobenzimidazole)Br3] (6b) [Sb(2- benzyl-2-thiopseudeourea)2Cl3] (7a) and [Sb(2- benzyl-2-thiopseudeourea)2Br3] (7b) were synthesized. Their structures were characterized by elemental analysis, molecular conductivity, FT-IR, (1)H NMR, LC-MS techniques. Glutathione reductase inhibitor activity, antimicrobial activity and DNA cleavage studies of the complexes were determined. The geometrical structures of the complexes were optimized by DFT/B3LYP method with LANL2DZ as basis set. Calculation results indicated that the equilibrium geometries of all complexes have square pyramidal shape. About 350 molecular descriptors (constitutional, topological, geometrical, electrostatic and quantum chemical parameters) of the complexes were calculated by DFT/B3LYP/LANL2DZ method with CODESSA software. Calculated molecular parameters were correlated to glutathione reductase inhibitory activity values (pIC50) of all complexes by Best Multi-Linear Regression (BMLR) method. Obtained two-parameter QSAR equation shows that increase in "maximum partial charge for a H atom" and decrease in HOMO-LUMO gap would be favorable for the glutathione reductase inhibitory activity. PMID:25459701

  18. DNA cleavage, antimicrobial studies and a DFT-based QSAR study of new antimony(III) complexes as glutathione reductase inhibitor

    Science.gov (United States)

    Tunç, Turgay; Koç, Yasemin; Açık, Leyla; Karacan, Mehmet Sayım; Karacan, Nurcan

    2015-02-01

    New antimony(III) complexes, [Sb(2-aminopyridine)2Cl3] (1a), [Sb(2-aminopyridine)2Br3] (1b), [Sb(5-methyl-2-aminopyridine)2Cl3] (2a), [Sb(5-methyl-2-aminopyridine)2Br3] (2b), [Sb(2-aminopyrimidine)2Cl3] (3a), [Sb(2-aminopyrimidine)2Br3] (3b), [Sb(4,6-dimethoxy-2-aminopyrimidine)2Cl3] (4a), [Sb(4,6-dimethoxy-2-aminopyrimidine)2Br3] (4b), [Sb(2-amino-1,3,5-triazine)2Cl3] (5a), [Sb(2-amino-1,3,5-triazine)2Br3] (5b), [Sb(2-guanidinobenzimidazole) Cl3] (6a), [Sb(2-guanidinobenzimidazole)Br3] (6b) [Sb(2- benzyl-2-thiopseudeourea)2Cl3] (7a) and [Sb(2- benzyl-2-thiopseudeourea)2Br3] (7b) were synthesized. Their structures were characterized by elemental analysis, molecular conductivity, FT-IR, 1H NMR, LC-MS techniques. Glutathione reductase inhibitor activity, antimicrobial activity and DNA cleavage studies of the complexes were determined. The geometrical structures of the complexes were optimized by DFT/B3LYP method with LANL2DZ as basis set. Calculation results indicated that the equilibrium geometries of all complexes have square pyramidal shape. About 350 molecular descriptors (constitutional, topological, geometrical, electrostatic and quantum chemical parameters) of the complexes were calculated by DFT/B3LYP/LANL2DZ method with CODESSA software. Calculated molecular parameters were correlated to glutathione reductase inhibitory activity values (pIC50) of all complexes by Best Multi-Linear Regression (BMLR) method. Obtained two-parameter QSAR equation shows that increase in "maximum partial charge for a H atom" and decrease in HOMO-LUMO gap would be favorable for the glutathione reductase inhibitory activity.

  19. Cloud point extraction combined with electrothermal atomic absorption spectrometry for the speciation of antimony(III) and antimony(V) in food packaging materials

    International Nuclear Information System (INIS)

    A simple, sensitive method for the speciation of inorganic antimony by cloud point extraction combined with electrothermal atomic absorption spectrometry (ETAAS) is presented and evaluated. The method based on the fact that formation of a hydrophobic complex of antimony(III) with ammonium pyrrolidine dithiocarbamate (APDC) at pH 5.0 and subsequently the hydrophobic complex enter into surfactant-rich phase, whereas antimony(V) remained in aqueous solutions. Antimony(III) in surfactant-rich phase was analyzed by ETAAS after dilution by 0.2 mL nitric acid in methanol (0.1 M), and antimony(V) was calculated by subtracting antimony(III) from the total antimony after reducing antimony(V) to antimony(III) by L-cysteine. The main factors affecting the cloud point extraction, such as pH, concentration of APDC and Triton X-114, equilibrium temperature and incubation time, sample volume were investigated in detail. Under the optimum conditions, the detection limit (3σ) of the proposed method was 0.02 ng mL-1 for antimony(III), and the relative standard deviation was 7.8% (c = 1.0 ng mL-1, n = 7). The proposed method was successfully applied to speciation of inorganic antimony in the leaching solutions of different food packaging materials with satisfactory results.

  20. Cloud point extraction combined with electrothermal atomic absorption spectrometry for the speciation of antimony(III) and antimony(V) in food packaging materials.

    Science.gov (United States)

    Jiang, Xiuming; Wen, Shengping; Xiang, Guoqiang

    2010-03-15

    A simple, sensitive method for the speciation of inorganic antimony by cloud point extraction combined with electrothermal atomic absorption spectrometry (ETAAS) is presented and evaluated. The method based on the fact that formation of a hydrophobic complex of antimony(III) with ammonium pyrrolidine dithiocarbamate (APDC) at pH 5.0 and subsequently the hydrophobic complex enter into surfactant-rich phase, whereas antimony(V) remained in aqueous solutions. Antimony(III) in surfactant-rich phase was analyzed by ETAAS after dilution by 0.2 mL nitric acid in methanol (0.1M), and antimony(V) was calculated by subtracting antimony(III) from the total antimony after reducing antimony(V) to antimony(III) by l-cysteine. The main factors affecting the cloud point extraction, such as pH, concentration of APDC and Triton X-114, equilibrium temperature and incubation time, sample volume were investigated in detail. Under the optimum conditions, the detection limit (3 sigma) of the proposed method was 0.02 ng mL(-1) for antimony(III), and the relative standard deviation was 7.8% (c=1.0 ng mL(-1), n=7). The proposed method was successfully applied to speciation of inorganic antimony in the leaching solutions of different food packaging materials with satisfactory results. PMID:19853991

  1. Cloud point extraction combined with electrothermal atomic absorption spectrometry for the speciation of antimony(III) and antimony(V) in food packaging materials

    Energy Technology Data Exchange (ETDEWEB)

    Jiang Xiuming; Wen Shengping [School of Chemistry and Chemical Engineering, Henan University of Technology, South Song Shan Road No. 140, Zhengzhou City 450001 (China); Xiang Guoqiang, E-mail: xianggq@haut.edu.cn [School of Chemistry and Chemical Engineering, Henan University of Technology, South Song Shan Road No. 140, Zhengzhou City 450001 (China)

    2010-03-15

    A simple, sensitive method for the speciation of inorganic antimony by cloud point extraction combined with electrothermal atomic absorption spectrometry (ETAAS) is presented and evaluated. The method based on the fact that formation of a hydrophobic complex of antimony(III) with ammonium pyrrolidine dithiocarbamate (APDC) at pH 5.0 and subsequently the hydrophobic complex enter into surfactant-rich phase, whereas antimony(V) remained in aqueous solutions. Antimony(III) in surfactant-rich phase was analyzed by ETAAS after dilution by 0.2 mL nitric acid in methanol (0.1 M), and antimony(V) was calculated by subtracting antimony(III) from the total antimony after reducing antimony(V) to antimony(III) by L-cysteine. The main factors affecting the cloud point extraction, such as pH, concentration of APDC and Triton X-114, equilibrium temperature and incubation time, sample volume were investigated in detail. Under the optimum conditions, the detection limit (3{sigma}) of the proposed method was 0.02 ng mL{sup -1} for antimony(III), and the relative standard deviation was 7.8% (c = 1.0 ng mL{sup -1}, n = 7). The proposed method was successfully applied to speciation of inorganic antimony in the leaching solutions of different food packaging materials with satisfactory results.

  2. Antimony(III) complexing with O-bearing organic ligands in aqueous solution: An X-ray absorption fine structure spectroscopy and solubility study

    Science.gov (United States)

    Tella, Marie; Pokrovski, Gleb S.

    2009-01-01

    The stability and structure of aqueous complexes formed by trivalent antimony (Sb III) with carboxylic acids (acetic, adipic, malonic, lactic, oxalic, tartaric, and citric acid), phenols (catechol), and amino acids (glycine) having O- and N-functional groups (carboxyl, alcoholic hydroxyl, phenolic hydroxyl and amine) typical of natural organic matter, were determined at 20 and 60 °C from solubility and X-ray absorption fine structure (XAFS) spectroscopy measurements. In organic-free aqueous solutions and in the presence of acetic, adipic, malonic acids and glycine, both spectroscopic and solubility data are consistent with the dominant formation of Sb III hydroxide species, Sb(OH)3-nn+,Sb(OH)30andSb(OH)4-, at strongly acid, acid-to-neutral and basic pH, respectively, demonstrating negligible complexing with mono-functional organic ligands (acetic) or those having non adjacent carboxylic groups (adipic, malonic). In contrast, in the presence of poly-functional carboxylic and hydroxy-carboxylic acids and catechol, Sb III forms stable 1:1 and 1:2 complexes with the studied organic ligands over a wide pH range typical of natural waters (3 cycle. Stability constants for these species, generated from Sb 2O 3 (rhomb.) solubility experiments, were used to model Sb complexing with natural humic acids possessing the same functional groups as those investigated in this study. Our predictions show that in an aqueous solution of pH between 2 and 10, containing 1 μg/L of Sb and 5 mg/L of dissolved organic carbon (DOC), up to 35% of total dissolved Sb binds to aqueous organic matter via carboxylic and hydroxy-carboxylic groups. This amount of complexed Sb for typical natural DOC concentrations is in agreement with that estimated from dialysis experiments performed with commercial humic acid in our work and those available in the literature for a range of standardized IHSS humic acids. Our results imply that a significant part of Sb is likely to be bound with humic acids via

  3. Quantitative HPLC-ICP-MS analysis of antimony redox speciation in complex sample matrices: new insights into the Sb-chemistry causing poor chromatographic recoveries

    DEFF Research Database (Denmark)

    Hansen, Claus; Schmidt, Bjørn; Larsen, Erik Huusfeldt;

    2011-01-01

    In solution antimony exists either in the pentavalent or trivalent oxidation state. As Sb(III) is more toxic than Sb(V), it is important to be able to perform a quantitative speciation analysis of Sb’s oxidation state. The most commonly applied chromatographic methods used for this redox speciation...... analysis do, however, often show a low chromatographic Sb recovery when samples of environmental or biological origin are analysed. In this study we explored basal chemistry of antimony and found that formation of macromolecules, presumably oligomeric and polymeric Sb(V) species, is the primary cause...... of low chromatographic recoveries. A combination of HPLC-ICP-MS, AFFF-ICP-MS and spinfiltration was applied for analysis of model compounds and biological samples. Quantitative chromatographic Sb redox speciation analysis was possible by acidic hydrolysis of the antimony polymers prior to analysis...

  4. Arsenic and antimony transporters in eukaryotes.

    Science.gov (United States)

    Maciaszczyk-Dziubinska, Ewa; Wawrzycka, Donata; Wysocki, Robert

    2012-01-01

    Arsenic and antimony are toxic metalloids, naturally present in the environment and all organisms have developed pathways for their detoxification. The most effective metalloid tolerance systems in eukaryotes include downregulation of metalloid uptake, efflux out of the cell, and complexation with phytochelatin or glutathione followed by sequestration into the vacuole. Understanding of arsenic and antimony transport system is of high importance due to the increasing usage of arsenic-based drugs in the treatment of certain types of cancer and diseases caused by protozoan parasites as well as for the development of bio- and phytoremediation strategies for metalloid polluted areas. However, in contrast to prokaryotes, the knowledge about specific transporters of arsenic and antimony and the mechanisms of metalloid transport in eukaryotes has been very limited for a long time. Here, we review the recent advances in understanding of arsenic and antimony transport pathways in eukaryotes, including a dual role of aquaglyceroporins in uptake and efflux of metalloids, elucidation of arsenic transport mechanism by the yeast Acr3 transporter and its role in arsenic hyperaccumulation in ferns, identification of vacuolar transporters of arsenic-phytochelatin complexes in plants and forms of arsenic substrates recognized by mammalian ABC transporters.

  5. Complexation-Coprecipitation Synthesis and Characterization of Neodymium and Antimony Doped SnO2 Conductive Nanoparticles

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Nd and Sb doped SnO2 conductive nanoparticles were prepared by the complexation-coprecipitation method with Sn, Sb2O3 and Nd2O3 as the raw materials. Thermal behavior, crystal phase, and structure of the prepared conductive nanoparticles were characterized by TG/DSC/DTG, FTIR, XRD and TEM techniques, respectively. The resistivity of the prepared conductive nanoparticles was 0.12 Ω·cm. TG/DSC/DTG curves show that the precursors lose weight completely before 750 ℃. FTIR spectrum shows that the vibration peaks are wide peaks in 731~617 cm-1, and the Nd and Sb doped SnO2 conductive nanoparticles have intense absorption in 4000~2000 cm-1. Nd and Sb doped SnO2 have a structure of tetragonal rutile, and complex doping is achieved well by complexation-coprecipitation method and is recognized as replacement doping or caulking doping. TME shows that the particles are weakly agglomerated, and the size of the particles calcined at 1000 ℃ ranges about 10 nm to 30 nm.

  6. Recent advances on antimony(III/V) compounds with potential activity against tumor cells.

    Science.gov (United States)

    Hadjikakou, S K; Ozturk, I I; Banti, C N; Kourkoumelis, N; Hadjiliadis, N

    2015-12-01

    Antimony one of the heavier pnictogens, has been in medical use against microbes and parasites as well. Antimony-based drugs have been prescribed against leishmaniasis since the parasitic transmission of the tropical disease was understood in the beginning of the 20th century. The activity of arsenic against visceral leishmaniasis led to the synthesis of an array of arsenic-containing parasitic agents, among them the less toxic pentavalent antimonials: Stibosan, Neostibosan, and Ureastibamine. Other antimony drugs followed: sodium stibogluconate (Pentostam) and melglumine antimoniate (Glucantim or Glucantime); both continue to be in use today despite their toxic side effects and increasing loss in potency due to the growing resistance of the parasite against antimony. Antimony compounds and their therapeutic potentials are under consideration from many research groups, while a number of early reviews recording advances of antimony biomedical applications are also available. However, there are only few reports on the screening for antitumor potential of antimony compounds. This review focuses upon results obtained on the anti-proliferative activity of antimony compounds in the past years. This survey shows that antimony(III/V) complexes containing various types of ligands such as thiones, thiosemicarbazones, dithiocarbamates, carboxylic acids, or ketones, nitrogen donor ligands, exhibit selectivity against a variety of cancer cells. The role of the ligand type of the complex is elucidated within this review. The complexes and their biological activity are already reported elsewhere. However quantitative structure-activity relationship (QSAR) modeling studies have been carried out and they are reported for the first time here. PMID:26092367

  7. Pentavalent Antimonials: New Perspectives for Old Drugs

    OpenAIRE

    Ribeiro, Raul R.; Cynthia Demicheli; Frédéric Frézard

    2009-01-01

    Pentavalent antimonials, including meglumine antimoniate and sodium stibogluconate, have been used for more than half a century in the therapy of the parasitic disease leishmaniasis. Even though antimonials are still the first-line drugs, they exhibit several limitations, including severe side effects, the need for daily parenteral administration and drug resistance. The molecular structure of antimonials, their metabolism and mechanism of action are still being investigated. Some recent stud...

  8. Leaching Mechanism of Complicated Antimony-Lead Concentrate and Sulfur Formation in Slurry Electrolysis

    Institute of Scientific and Technical Information of China (English)

    WangChengyan; QiuDingfan; JiangPeihai

    2004-01-01

    Anodic reaction mechanism of complicated antimony-lead concentrate in slurry electrolysis was investigated by the anodic polarization curves determined under various conditions. The main reactions on the anode are the oxidations of FeCln(2-n) . Though the oxidation of jamesonite particle on the anode can occur during the whole process, it is less. With the help of mineralogy studies and relevant tests, the leaching reaction mechanism of jameson[to and gudmundite during slurry electrolysis was ascertained. Because of the oxidation reaction of FeCl3 produced by antimony-lead concentrate itself, the non-oxidation complex acid dissolution of jameson[re, the oxidation complex acid dissolution of gudmundite, and the oxidation of air carried by stirring, the leaching ratio of antimony reaches about 35% when HCl-NH4Cl solution is used to leach antimony-lead concentrate directly. So when the theoretical electric quantity is given to oxidation of antimony in slurry electrolysis, all of antimony, lead and iron containing in antimony-lead concentrate, are leached. The formation of sulfur is through the directly redox reaction of Fe3+ and jameson[re. The S2- in jamesonite is oxidized into S0 , and forms the crystals of sulfur again on the spot. The redox reaction of Fe3+ and H2S formed by non-oxidative acid dissolution of jamesonite is less.

  9. Pentavalent Antimonials: New Perspectives for Old Drugs

    Directory of Open Access Journals (Sweden)

    Raul R. Ribeiro

    2009-06-01

    Full Text Available Pentavalent antimonials, including meglumine antimoniate and sodium stibogluconate, have been used for more than half a century in the therapy of the parasitic disease leishmaniasis. Even though antimonials are still the first-line drugs, they exhibit several limitations, including severe side effects, the need for daily parenteral administration and drug resistance. The molecular structure of antimonials, their metabolism and mechanism of action are still being investigated. Some recent studies suggest that pentavalent antimony acts as a prodrug that is converted to active and more toxic trivalent antimony. Other works support the direct involvement of pentavalent antimony. Recent data suggest that the biomolecules, thiols and ribonucleosides, may mediate the actions of these drugs. This review will summarize the progress to date on the chemistry and biochemistry of pentavalent antimony. It will also present the most recent works being done to improve antimonial chemotherapy. These works include the development of simple synthetic methods for pentavalent antimonials, liposome-based formulations for targeting the Leishmania parasites responsible for visceral leishmaniasis and cyclodextrin-based formulations to promote the oral delivery of antimony.

  10. Separation of traffic related antimony compounds

    International Nuclear Information System (INIS)

    Complete text of publication follows. It is known that most of the brake pads contain Sb2S3 as lubricant to achieve better friction stability. Due to braking the brake lining crumbles away and its Sb content gets into the air. As a result of the temperature increase accompanying the braking a part of the antimony may oxidize to oxides, as Sb2O3 or even to the more stable form, Sb2O4. Since Sb2O3 more readily soluble than the others, its absorption from the lung so its environmental impact effect is more harmful. After a systematic investigation involving solubilization of the solid compounds, citric and tartaric acid as well as 6 mol/dm3 HCl were tested for leaching of trace antimony compounds from natural matrix. To prepare reference material related to these species, soil and activated charcoal was spiked in 10 μg/g concentration with all the three material (Sb2S3, Sb2O3,Sb2O4). separately. Recovery of the different forms was checked by graphite furnace atomic absorption spectrometric (GFAAS) analysis of the leachates. The soil was confirmed to oxidize the sulfide content while the activated charcoal was established to enrich antimony from HCl solution as ion association complex. It was concluded, that Sb2S3 is leached only in slight amount in 4 hours by 0.1-0.5 mol/dm3 citric acid, while leaching of Sb2O3 is quantitative. On the other side, it was proved that Sb2O3 as well as Sb2S3 traces are soluble in 6 HCl solution in 60 min, whilst Sb2O4 is not destroyed. So, the Sb2O3 and Sb2S3 content of a flying dust can be determined. The GFAAS temperature program had to be modified in order to be capable to analyze high organic matrix as citric or tartaric acid even in 0.5 mol/dm3 concentration. Concerning their decomposition temperature an additional step was inserted into the temperature program, pyrolysis on 300 and 400 deg C, respectively. The antimony concentration of the highly acidic leachates were determined by hydride generation GFAAS. The reproducibility of

  11. Coordination- and Redox-Noninnocent Behavior of Ambiphilic Ligands Containing Antimony.

    Science.gov (United States)

    Jones, J Stuart; Gabbaï, François P

    2016-05-17

    Stimulated by applications in catalysis, the chemistry of ambiphilic ligands featuring both donor and acceptor functionalities has experienced substantial growth in the past several years. The unique opportunities in catalysis offered by ambiphilic ligands stem from the ability of their acceptor functionalities to play key roles via metal-ligand cooperation or modulation of the reactivity of the metal center. Ligands featuring group 13 centers, most notably boranes, as their acceptor functionalities have undoubtedly spearheaded these developments, with remarkable results having been achieved in catalytic hydrogenation and hydrosilylation. Motivated by these developments as well as by our fundamental interest in the chemistry of heavy group 15 elements, we became fascinated by the possibility of employing antimony centers as Lewis acids within ambiphilic ligands. The chemistry of antimony-based ligands, most often encountered as trivalent stibines, has historically been considered to mirror that of their lighter phosphorus-based congeners. There is growing evidence, however, that antimony-based ligands may display unique coordination behavior and reactivity. Additionally, despite the diverse Lewis acid and redox chemistry that antimony exhibits, there have been only limited efforts to explore this chemistry within the coordination sphere of a transition metal. By incorporation of antimony into the framework of polydentate ligands in order to enforce the main group metal-transition metal interaction, the effect of redox and coordination events at the antimony center on the structure, electronics, and reactivity of the metal complex may be investigated. This Account describes our group's continuing efforts to probe the coordination behavior, reactivity, and application of ambiphilic ligands incorporating antimony centers. Structural and theoretical studies have established that both Sb(III) and Sb(V) centers in polydentate ligands may act as Z-type ligands toward late

  12. Coordination- and Redox-Noninnocent Behavior of Ambiphilic Ligands Containing Antimony.

    Science.gov (United States)

    Jones, J Stuart; Gabbaï, François P

    2016-05-17

    Stimulated by applications in catalysis, the chemistry of ambiphilic ligands featuring both donor and acceptor functionalities has experienced substantial growth in the past several years. The unique opportunities in catalysis offered by ambiphilic ligands stem from the ability of their acceptor functionalities to play key roles via metal-ligand cooperation or modulation of the reactivity of the metal center. Ligands featuring group 13 centers, most notably boranes, as their acceptor functionalities have undoubtedly spearheaded these developments, with remarkable results having been achieved in catalytic hydrogenation and hydrosilylation. Motivated by these developments as well as by our fundamental interest in the chemistry of heavy group 15 elements, we became fascinated by the possibility of employing antimony centers as Lewis acids within ambiphilic ligands. The chemistry of antimony-based ligands, most often encountered as trivalent stibines, has historically been considered to mirror that of their lighter phosphorus-based congeners. There is growing evidence, however, that antimony-based ligands may display unique coordination behavior and reactivity. Additionally, despite the diverse Lewis acid and redox chemistry that antimony exhibits, there have been only limited efforts to explore this chemistry within the coordination sphere of a transition metal. By incorporation of antimony into the framework of polydentate ligands in order to enforce the main group metal-transition metal interaction, the effect of redox and coordination events at the antimony center on the structure, electronics, and reactivity of the metal complex may be investigated. This Account describes our group's continuing efforts to probe the coordination behavior, reactivity, and application of ambiphilic ligands incorporating antimony centers. Structural and theoretical studies have established that both Sb(III) and Sb(V) centers in polydentate ligands may act as Z-type ligands toward late

  13. Geochemical Studies on Dachang Antimony Ore Deposit in Qinglong,Guizhou Province

    Institute of Scientific and Technical Information of China (English)

    张启厚

    1999-01-01

    The Dachang antimony deposit in Qinglong,Guizhou Province,is strictly controlled by the “Dachang Layer” which is a complex altered rock occurring at unconformity between the Permian Emeishan basalt and the Maokou limestone.Based on the studies of the hanging-and foot-wall rocks,the trace elements and REE contents of the rocks and ores and heavy placer minerals in the basalt,this paper is focused on the relations between these data and the “Dachang Layer”and its hanging- and oot-wall rocks.The author pointed out that the “Dachang Layer” and basalt are the source-beds of antimony;ilmenite and magnetite are the major mineral carriers of antimony.In the processes of halmyrosis and burial metamorphism of the “Dachang Layer” an basalt,antimony was mobilized along with the mobilization of iron and was preliminarily concentrated in the“ Dachang Layer”.

  14. In Vitro antileishmanial properties of neutron-irradiated meglumine antimoniate

    Directory of Open Access Journals (Sweden)

    Samanta Etel Treiger Borborema

    2005-10-01

    Full Text Available Pentavalent antimony, as meglumine antimoniate (Glucantime® or sodium stibogluconate (Pentostam® , is the main treatment for leishmaniasis, a complex of diseases caused by the protozoan Leishmania, and an endemic and neglected threat in Brazil. Despite over half a century of clinical use, their mechanism of action, toxicity and pharmacokinetic data remain unknown. The analytical methods for determination of antimony in biological systems remain complex and have low sensitivity. Radiotracer studies have a potential in pharmaceutical development. The aim of this study was to obtain a radiotracer for antimony, with suitable physical and biological properties. Meglumine antimoniate was neutron irradiated inside the IEA-R1 nuclear reactor, producing two radioisotopes 122Sb and 124Sb, with high radionuclidic purity and good specific activity. This compound showed the same antileishmanial activity as the native compound. The use of the radiotracers, easily created by neutron irradiation, could be an interesting tool to solve important questions in antimonial pharmacology.Os antimoniais pentavalentes, como o antimoniato de meglumina (Glucantime® ou estibogluconato de sódio (Pentostam® , são o principal tratamento para a leishmaniose, um complexo de doenças causadas pelo protozoário parasita Leishmania, uma doença endêmica e negligenciada no Brasil. Apesar do seu uso clínico por mais de meio século, seu mecanismo de ação, toxicidade e dados de farmacocinética permanecem desconhecidos. Os métodos analíticos para determinação de antimônio em sistemas biológicos são complexos e apresentam baixa sensibilidade. Estudos utilizando radiotraçadores têm papel potencial no desenvolvimento farmacológico. O objetivo deste estudo foi desenvolver um radiotraçador de antimônio, com propriedades físicas e biológicas adequadas. O antimoniato de meglumina foi irradiado por nêutrons no reator nuclear IEA-R1, produzindo dois radioisótopos: 122

  15. The Hydrothermal Chemistry of Gold, Arsenic, Antimony, Mercury and Silver

    Energy Technology Data Exchange (ETDEWEB)

    Bessinger, Brad; Apps, John A.

    2003-03-23

    A comprehensive thermodynamic database based on the Helgeson-Kirkham-Flowers (HKF) equation of state was developed for metal complexes in hydrothermal systems. Because this equation of state has been shown to accurately predict standard partial molal thermodynamic properties of aqueous species at elevated temperatures and pressures, this study provides the necessary foundation for future exploration into transport and depositional processes in polymetallic ore deposits. The HKF equation of state parameters for gold, arsenic, antimony, mercury, and silver sulfide and hydroxide complexes were derived from experimental equilibrium constants using nonlinear regression calculations. In order to ensure that the resulting parameters were internally consistent, those experiments utilizing incompatible thermodynamic data were re-speciated prior to regression. Because new experimental studies were used to revise the HKF parameters for H2S0 and HS-1, those metal complexes for which HKF parameters had been previously derived were also updated. It was found that predicted thermodynamic properties of metal complexes are consistent with linear correlations between standard partial molal thermodynamic properties. This result allowed assessment of several complexes for which experimental data necessary to perform regression calculations was limited. Oxygen fugacity-temperature diagrams were calculated to illustrate how thermodynamic data improves our understanding of depositional processes. Predicted thermodynamic properties were used to investigate metal transport in Carlin-type gold deposits. Assuming a linear relationship between temperature and pressure, metals are predicted to predominantly be transported as sulfide complexes at a total aqueous sulfur concentration of 0.05 m. Also, the presence of arsenic and antimony mineral phases in the deposits are shown to restrict mineralization within a limited range of chemical conditions. Finally, at a lesser aqueous sulfur

  16. FIRST REPORT ON OTOTOXICITY OF MEGLUMINE ANTIMONIATE

    Directory of Open Access Journals (Sweden)

    Cláudia Maria Valete-Rosalino

    2014-09-01

    Full Text Available Introduction: Pentavalent antimonials are the first drug of choice in the treatment of tegumentary leishmaniasis. Data on ototoxicity related with such drugs is scarcely available in literature, leading us to develop a study on cochleovestibular functions. Case Report: A case of a tegumentary leishmaniasis patient, a 78-year-old man who presented a substantial increase in auditory threshold with tinnitus and severe rotatory dizziness during the treatment with meglumine antimoniate, is reported. These symptoms worsened in two weeks after treatment was interrupted. Conclusion: Dizziness and tinnitus had already been related to meglumine antimoniate. However, this is the first well documented case of cochlear-vestibular toxicity related to meglumine antimoniate.

  17. Preparation and properties of antimony thin film anode materials

    Institute of Scientific and Technical Information of China (English)

    SU Shufa; CAO Gaoshao; ZHAO Xinbing

    2004-01-01

    Metallic antimony thin films were deposited by magnetron sputtering and electrodeposition. Electrochemical properties of the thin film as anode materials for lithium-ion batteries were investigated and compared with those of antimony powder. It was found that both magnetron sputtering and electrodeposition are easily controllable processes to deposit antimony films with fiat charge/discharge potential plateaus. The electrochemical performances of antimony thin films, especially those prepared with magnetron sputtering, are better than those of antimony powder. The reversible capacities of the magnetron sputtered antimony thin film are above 400 mA h g-1 in the first 15 cycles.

  18. Sodium Antimony Gluconate Induces Generation of Reactive Oxygen Species and Nitric Oxide via Phosphoinositide 3-Kinase and Mitogen-Activated Protein Kinase Activation in Leishmania donovani-Infected Macrophages

    OpenAIRE

    Mookerjee Basu, Jayati; Mookerjee, Ananda; Sen, Prosenjit; Bhaumik, Suniti; Sen, Pradip; Banerjee, Subha; Naskar, Ksudiram; Choudhuri, Soumitra K.; Saha, Bhaskar; Raha, Sanghamitra; Roy, Syamal

    2006-01-01

    Pentavalent antimony complexes, such as sodium stibogluconate and sodium antimony gluconate (SAG), are still the first choice for chemotherapy against various forms of leishmaniasis, including visceral leishmaniasis, or kala-azar. Although the requirement of a somewhat functional immune system for the antileishmanial action of antimony was reported previously, the cellular and molecular mechanism of action of SAG was not clear. Herein, we show that SAG induces extracellular signal-regulated k...

  19. 21 CFR 862.3110 - Antimony test system.

    Science.gov (United States)

    2010-04-01

    ... antimony, a heavy metal, in urine, blood, vomitus, and stomach contents. Measurements obtained by this device are used in the diagnosis and treatment of antimony poisoning. (b) Classification. Class I....

  20. Infrared surface polaritons on antimony.

    Science.gov (United States)

    Cleary, Justin W; Medhi, Gautam; Shahzad, Monas; Rezadad, Imen; Maukonen, Doug; Peale, Robert E; Boreman, Glenn D; Wentzell, Sandy; Buchwald, Walter R

    2012-01-30

    The semimetal antimony, with a plasma frequency ~80 times less than that of gold, is potentially useful as a host for infrared surface polaritons (SPs). Relevant IR SP properties, including the frequency-dependent propagation length and penetration depths for fields into the media on either side of the interface, were determined from optical constants measured on optically-thick thermally-evaporated Sb films over the wavelength range 1 to 40 μm. Plasma and carrier relaxation frequencies were determined from Drude-model fits to these data. The real part of the permittivity is negative for wavelengths beyond 11 μm. Distinct resonant decreases in specular reflected intensity were observed for Sb lamellar gratings in the wavelength range of 6 to 11 μm, where the real part of the permittivity is positive. Both resonance angles and the angular reflectance spectral line shapes are in agreement with theory for excitation of bound surface electromagnetic waves (SPs). Finite element method (FEM) electrodynamic simulations indicate the existence of SP modes under conditions matching the experiments. FEM results also show that such waves depend on having a significant imaginary part of the permittivity, as has been noted earlier for the case of surface exciton polaritons.

  1. On-line lab-in-syringe cloud point extraction for the spectrophotometric determination of antimony.

    Science.gov (United States)

    Frizzarin, Rejane M; Portugal, Lindomar A; Estela, José M; Rocha, Fábio R P; Cerdà, Victor

    2016-02-01

    Most of the procedures for antimony determination require time-consuming sample preparation (e.g. liquid-liquid extraction with organic solvents), which are harmful to the environment. Because of the high antimony toxicity, a rapid, sensitive and greener procedure for its determination becomes necessary. The goal of this work was to develop an analytical procedure exploiting for the first time the cloud point extraction on a lab-in-syringe flow system aiming at the spectrophotometric determination of antimony. The procedure was based on formation of an ion-pair between the antimony-iodide complex and H(+) followed by extraction with Triton X-114. The factorial design showed that the concentrations of ascorbic acid, H2SO4 and Triton X-114, as well as second and third order interactions were significant at the 95% confidence level. A Box-Behnken design was applied to obtain the response surfaces and to identify the critical values. System is robust at the 95% confidence level. A linear response was observed from 5 to 50 µg L(-1), described by the equation A=0.137+0.050C(Sb) (r=0.998). The detection limit (99.7% confidence level), the coefficient of variation (n=5; 15 µg L(-1)) and the sampling rate was estimated at 1.8 µg L(-1), 1.6% and 16 h(-1), respectively. The procedure allows quantification of antimony in the concentrations established by environmental legislation (6 µg L(-1)) and it was successfully applied to the determination of antimony in freshwater samples and antileishmanial drugs, yielding results in agreement with those obtained by HGFAAS at the 95% confidence level.

  2. Synthesis and application of antimony pent(isooctyl thioglycollate)

    Institute of Scientific and Technical Information of China (English)

    LIU You-nian; LI Hong-bing; SHU Wan-gen; CHEN Qi-yuan

    2005-01-01

    A new type of thermal stabilizer, antimony pent(isooctyl thioglycollate)(Sb(SCH2COOC8H17)5), was synthesized by using antimony trioxide, isooctanol and thioglycolic acid in 2 steps. Firstly, antimony trioxide was oxidized into colloidal antimony peroxide. Then antimony peroxide and isooctyl thioglycollate reacted stoichiometrically for 2 h with the yield of 87%. This compound was used as thermal stabilizer for polyvinyl chloride(PVC). The results show that the thermal stability time is 52 min at 200 ℃ by heat-ageing oven test when adding 2.5% thermal stabilizer to PVC resin. Compared with antimony tris(isooctyl thiolycollate), the initial thermal stability of antimony pent(isooctyl thioglycollate) is better than that of antimony tris(isooctyl thioglycollate), while the long-term thermal stability time is shorter than that of antimony tris(isooctyl thioglycollate). Meanwhile, the synergism of antimony pent(isooctyl thioglycollate) with calcium stearate was studied, indicating that when the mass ratio of antimony pent(isooctyl thioglycollate) to calcium stearate is 2:1, the thermal stability time of PVC is 58 min.

  3. Vacuum Evaporation Technology for Treating Antimony-Rich Anode Slime

    Science.gov (United States)

    Qiu, Keqiang; Lin, Deqiang; Yang, Xuelin

    2012-11-01

    A vacuum evaporation technology for treating antimony-rich anode slime was developed in this work. Experiments were carried out at temperatures from 873 K to 1073 K and residual gas pressures from 50 Pa to 600 Pa. During vacuum evaporation, silver from the antimony-rich anode slime was left behind in the distilland in a silver alloy containing antimony and lead, and antimony trioxide was evaporated. The experimental results showed that 92% by weight of antimony can be removed, and the silver content in the alloy was up to 12.84%. The antimony trioxide content in the distillate was more than 99.7%, and the distillate can be used directly as zero-grade antimony trioxide (China standard).

  4. Microbial antimony biogeochemistry: Enzymes, regulation, and related metabolic pathways

    Science.gov (United States)

    Li, Jingxin; Qian Wang,; Oremland, Ronald S.; Kulp, Thomas R.; Rensing, Christopher; Wang, Gejiao

    2016-01-01

    Antimony (Sb) is a toxic metalloid that occurs widely at trace concentrations in soil, aquatic systems, and the atmosphere. Nowadays, with the development of its new industrial applications and the corresponding expansion of antimony mining activities, the phenomenon of antimony pollution has become an increasingly serious concern. In recent years, research interest in Sb has been growing and reflects a fundamental scientific concern regarding Sb in the environment. In this review, we summarize the recent research on bacterial antimony transformations, especially those regarding antimony uptake, efflux, antimonite oxidation, and antimonate reduction. We conclude that our current understanding of antimony biochemistry and biogeochemistry is roughly equivalent to where that of arsenic was some 20 years ago. This portends the possibility of future discoveries with regard to the ability of microorganisms to conserve energy for their growth from antimony redox reactions and the isolation of new species of “antimonotrophs.”

  5. Synthesis of antimony tris(mercaptoethyl carboxylates) as thermal stabilizer for polyvinyl chloride

    Institute of Scientific and Technical Information of China (English)

    舒万艮; 刘又年; 陈启元

    2002-01-01

    A novel type of thermal stabilizers-antimony tris(mercaptoethyl carboxylates) (Sb(SCH2CH2OOCR) 3), was synthesized from carboxylic acid, antimony trioxide and 2-mercaptoethanol in two steps. The experimental results show that the molar ratio of carboxylic acid to antimony tris(2-hydroxyethyl mercaptide) is 1.2, when adding 0.6% tetra-n-butyl titanate as catalyst and xylene as isotropic solvent, heating and refluxing for about 2~4h. The thermal stability was measured by heat-aging oven test. The thermal stability time is about 8~40min(at 200℃) when adding 2% tetra-n-butyl titanate in polyvinyl chloride(PVC). Among these stabilizers, antimony tris(mercaptoethyl stearate) has best thermal stability. Its thermal stability is better than that of Ca-Zn complex and basic lead stabilizers, and equal to that of organotin. In addition, the stabilization mechanism of this kind of stabilizers for PVC was discussed briefly.

  6. Pharmacokinetic of antimony in mice with cutaneous Leishmaniasis

    Energy Technology Data Exchange (ETDEWEB)

    Borborema, Samanta E.T.; Nascimento, Nanci do [Instituto de Pesquisas Energeticas e Nucleares IPEN/CNEN-SP, Sao Paulo, SP (Brazil). Lab. de Biologia Molecular]. E-mails: samanta@usp.br; nnascime@ipen.br; Andrade Junior, Heitor F. de [Instituto de Pesquisas Energeticas e Nucleares IPEN/CNEN-SP, Sao Paulo, SP (Brazil). Lab. de Biologia Molecular; Instituto de Medicina Tropical de Sao Paulo, Sao Paulo, SP (Brazil); E-mail: hfandrad@usp.br; Osso Junior, Joao A. [Instituto de Pesquisas Energeticas e Nucleares IPEN/CNEN-SP, Sao Paulo, SP (Brazil). Centro de Radiofarmacia]. E-mail: jaosso@ipen.br

    2007-07-01

    Cutaneous Leishmaniasis (CL) remains a major world health problem, with about 1.5 million new cases each year. Caused by protozoa Leishmania, in South America, this infection can vary from a chronic skin ulcer, to an erosive mucosal disease and severe facial disfigurement. Pentavalent antimony (Sb{sup +5}) as sodium stibogluconate (Pentostam) or meglumine antimoniate (Glucantime) are main drugs for treating most forms of human leishmaniasis. For six decades, despite the recent developments, the effective therapy to cutaneous leishmaniasis has been based on long parenteral courses of such drugs, even though these are fairly costly, toxic and inconvenient to use, without adequate knowledge on their pharmacokinetics or mechanism of action. Pharmacokinetics studies could be based on bioactive traceable drugs, usually with radioactive isotopes, but antimony radioisotopes are unavailable commercially. Neutron irradiation is a powerful tool in the analysis of mineral content of samples, for antimony, there are at least two main isotopes that could be formed after neutron irradiation in nuclear reactor. The aim of the present study was to construct antimony salts with those radioisotopes to obtain tracers to compare the pharmacokinetic and the tissue distribution of neutron irradiated meglumine antimoniate in healthy and cutaneous leishmaniasis experimentally infected mice. Meglumine antimoniate, (Glucantime, Aventis, S.P, Brazil), was neutron irradiated inside the IEA-R1 nuclear reactor (IPEN/CNEN-SP), producing two radioisotopes {sup 122}Sb and {sup 124}Sb. Its biodistribution was verified in BALB/c mice experimentally infected with Leishmania (Leishmania) Amazonensis, which received a single intraperitoneal dose of the drug. At different times after injection, the tissues and blood were excised and activity measured in a NaI (Tl) scintillation counter. Compared with the healthy mice, experimentally infected mice had significantly lower maximum concentration of antimony

  7. Polycrystalline thin films of antimony selenide via chemical bath deposition and post deposition treatments

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez-Lazcano, Y. [Department of Solar Energy Materials, Centro de Investigacion en Energia, Universidad Nacional Autonoma de Mexico, Temixco, Morelos-62580 (Mexico); Pena, Yolanda [Department of Solar Energy Materials, Centro de Investigacion en Energia, Universidad Nacional Autonoma de Mexico, Temixco, Morelos-62580 (Mexico); Nair, M.T.S. [Department of Solar Energy Materials, Centro de Investigacion en Energia, Universidad Nacional Autonoma de Mexico, Temixco, Morelos-62580 (Mexico)]. E-mail: mtsn@cie.unam.mx; Nair, P.K. [Department of Solar Energy Materials, Centro de Investigacion en Energia, Universidad Nacional Autonoma de Mexico, Temixco, Morelos-62580 (Mexico)

    2005-12-22

    We report a method for obtaining thin films of polycrystalline antimony selenide via chemical bath deposition followed by heating the thin films at 573 K in selenium vapor. The thin films deposited from chemical baths containing one or more soluble complexes of antimony, and selenosulfate initially did not show X-ray diffraction (XRD) patterns corresponding to crystalline antimony selenide. Composition of the films, studied by energy dispersive X-ray analyses indicated selenium deficiency. Heating these films in presence of selenium vapor at 573 K under nitrogen (2000 mTorr) resulted in an enrichment of Se in the films. XRD peaks of such films matched Sb{sub 2}Se{sub 3}. Evaluation of band gap from optical spectra of such films shows absorption due to indirect transition occurring in the range of 1-1.2 eV. The films are photosensitive, with dark conductivity of about 2 x 10{sup -8} ({omega} cm){sup -1} and photoconductivity, about 10{sup -6} ({omega} cm){sup -1} under tungsten halogen lamp illumination with intensity of 700 W m{sup -2}. An estimate for the mobility life time product for the film is 4 x 10{sup -9} cm{sup 2} V{sup -1}.

  8. Selective determination of antimony(III) and antimony(V) with ammonium pyrrolidinedithiocarbamate, sodium diethyldithiocarbamate and dithizone by atomic-absorption spectrometry with a carbon-tube atomizer.

    Science.gov (United States)

    Kamada, T; Yamamoto, Y

    1977-05-01

    The extraction behaviour of antimony(III) and antimony(V) with ammonium pyrrolidinedithiocarbamate, sodium diethyldithiocarbamate and dithizone in organic solvents has been investigated by means of frameless atomic-absorption spectrophotometry with a carbon-tube atomizer. The selective extraction of antimony(III) and differential determination of antimony(III) and antimony(V) have been developed. With ammonium pyrrolidinedithiocarbamate and methyl isobutyl ketone, when the aqueous phase/solvent volume ratio is 50 ml/10 ml and the injection volume in the carbon tube is 20 mul, the sensitivity for antimony is 0.2 ng/ml for 1% absorption. The relative standard deviations are ca. 2%. Interferences by many metal ions can be prevented by masking with EDTA. The proposed methods have been applied satisfactorily to determination of antimony(III) and antimony(V) in various types of water. PMID:18962096

  9. Structural and electrical characterization of zinc oxide doped with antimony

    Directory of Open Access Journals (Sweden)

    G. Juárez Díaz

    2014-08-01

    Full Text Available In this work we report the results of structural and electrical characterization realized on zinc oxide single crystal samples with (001 orientation, which were doped with antimony. Doping was carried out by antimony thermal diffusion at 1000 °C for periods of 1 and 2 hours under nitrogen environment from a solid source formed by antimony oxide. Electrical characterization by I-V curves and Hall effect shown an increase in acceptor concentration which demonstrates that doping is effective and create holes in zinc oxide samples.

  10. Electrodeposition Mechanism of Trivalent Antimony%三价锑的电沉积机理

    Institute of Scientific and Technical Information of China (English)

    林艳; 谢刚; 杨大锦

    2011-01-01

    The reduction mechanism of Sb3+ in H2SO4-NH4F-SbF3 electrolyte system was studied by means of electrochemical methods, including chronopotentiometry and alternating current impedance.Analysis of potential-time transients clearly shows that antimony (Ⅲ) could be reduced to antimony metal via two-steps irreversible electron transfer process in H2SO4-NH4F-SbF3 system.The relationship between iτ1/2 and i calculated by chronopotentiometry indicates that the trivalent antimony complex undergoes chemical transformation reaction before its reduction in the cathode.The impedance results confirm the above conclusion and indicate that the adsorption states which are the middle product of trivalent antimony have different influences on two electron transfer steps.%采用恒电流阶跃法及交流阻抗法等电化学方法,研究了H2SO4-NH4F-SbF3体系中三价锑的阴极还原机理.电势~时间暂态曲线出现二步反应特征,表明Sb"还原分两步进行.由恒电流阶跃曲线中iτ1/2~i关系可知Sb3+阴极还原存在前置化学转化.Sb3+阴极还原的交流阻抗测定结果进一步验证Sb3+还原是存在化学前置转化步骤的二步反应,且电活性中间产物吸附在电极表面,吸附反应对两步电子转移步骤的影响不同.

  11. Deposition of rod-shaped antimony sulfide thin films from single-source antimony thiosemicarbazone precursors

    Energy Technology Data Exchange (ETDEWEB)

    Biswal, Jasmine B.; Sawant, Narayan V. [Department of Chemistry, University of Mumbai, Vidyanagari, Santacruz (East), Mumbai - 400 098 (India); Garje, Shivram S., E-mail: ssgarje@chem.mu.ac.i [Department of Chemistry, University of Mumbai, Vidyanagari, Santacruz (East), Mumbai - 400 098 (India)

    2010-04-02

    Antimony sulfide thin films were deposited on glass substrates by aerosol assisted chemical vapour deposition technique using single source precursors, namely, antimony(III) thiosemicarbazones, SbCl{sub 3}(L) (L = thiosemicarbazones of thiophene-2-carboxaldehyde (1) and cinnamaldehyde (2)). The deposited films were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive X-ray analysis and UV-visible spectroscopy in order to identify their phases, morphologies, compositions and optical properties respectively. These characterizations revealed that the films were comprised of rod-shaped particles of orthorhombic stibnite (Sb{sub 2}S{sub 3}) with a Sb:S stoichiometry of {approx} 1:1.3. The calculated optical band gap from UV-vis absorption spectrum is found to be 3.48 eV.

  12. Tissue distribution of residual antimony in rats treated with multiple doses of meglumine antimoniate

    Directory of Open Access Journals (Sweden)

    Deise Riba Coelho

    2014-07-01

    Full Text Available Meglumine antimoniate (MA and sodium stibogluconate are pentavalent antimony (SbV drugs used since the mid-1940s. Notwithstanding the fact that they are first-choice drugs for the treatment of leishmaniases, there are gaps in our knowledge of their toxicological profile, mode of action and kinetics. Little is known about the distribution of antimony in tissues after SbV administration. In this study, we evaluated the Sb content of tissues from male rats 24 h and three weeks after a 21-day course of treatment with MA (300 mg SbV/kg body wt/d, subcutaneous. Sb concentrations in the blood and organs were determined by inductively coupled plasma-mass spectrometry. In rats, as with in humans, the Sb blood levels after MA dosing can be described by a two-compartment model with a fast (t1/2 = 0.6 h and a slow (t1/2 >> 24 h elimination phase. The spleen was the organ that accumulated the highest amount of Sb, while bone and thyroid ranked second in descending order of tissues according to Sb levels (spleen >> bone, thyroid, kidneys > liver, epididymis, lungs, adrenals > prostate > thymus, pancreas, heart, small intestines > skeletal muscle, testes, stomach > brain. The pathophysiological consequences of Sb accumulation in the thyroid and Sb speciation in the liver, thyroid, spleen and bone warrant further studies.

  13. How can we adapt to geological scarcity of antimony? Investigation of antimony's substitutability and of other measures to achieve a sustainable use

    NARCIS (Netherlands)

    Henckens, M.L.C.M.; Driessen, P.P.J.; Worrell, E.

    2016-01-01

    Abstract Antimony is an element that is applied in many useful applications for mankind. However, antimony resources are very scarce, when comparing the current extraction rates with the availability of antimony containing ores. From an inter-temporal sustainability perspective, current generations

  14. Chronic exposure to arsenic in drinking water can lead to resistance to antimonial drugs in a mouse model of visceral leishmaniasis

    Science.gov (United States)

    Perry, Meghan R.; Wyllie, Susan; Raab, Andrea; Feldmann, Joerg; Fairlamb, Alan H.

    2013-01-01

    The Indian subcontinent is the only region where arsenic contamination of drinking water coexists with widespread resistance to antimonial drugs that are used to treat the parasitic disease visceral leishmaniasis. We have previously proposed that selection for parasite resistance within visceral leishmaniasis patients who have been exposed to trivalent arsenic results in cross-resistance to the related metalloid antimony, present in the pentavalent state as a complex in drugs such as sodium stibogluconate (Pentostam) and meglumine antimonate (Glucantime). To test this hypothesis, Leishmania donovani was serially passaged in mice exposed to arsenic in drinking water at environmentally relevant levels (10 or 100 ppm). Arsenic accumulation in organs and other tissues was proportional to the level of exposure and similar to that previously reported in human liver biopsies. After five monthly passages in mice exposed to arsenic, isolated parasites were found to be completely refractory to 500 μg⋅mL−1 Pentostam compared with the control passage group (38.5 μg⋅mL−1) cultured in vitro in mouse peritoneal macrophages. Reassessment of resistant parasites following further passage for 4 mo in mice without arsenic exposure showed that resistance was stable. Treatment of infected mice with Pentostam confirmed that resistance observed in vitro also occurred in vivo. We conclude that arsenic contamination may have played a significant role in the development of Leishmania antimonial resistance in Bihar because inadequate treatment with antimonial drugs is not exclusive to India, whereas widespread antimonial resistance is. PMID:24167266

  15. Chronic exposure to arsenic in drinking water can lead to resistance to antimonial drugs in a mouse model of visceral leishmaniasis.

    Science.gov (United States)

    Perry, Meghan R; Wyllie, Susan; Raab, Andrea; Feldmann, Joerg; Fairlamb, Alan H

    2013-12-01

    The Indian subcontinent is the only region where arsenic contamination of drinking water coexists with widespread resistance to antimonial drugs that are used to treat the parasitic disease visceral leishmaniasis. We have previously proposed that selection for parasite resistance within visceral leishmaniasis patients who have been exposed to trivalent arsenic results in cross-resistance to the related metalloid antimony, present in the pentavalent state as a complex in drugs such as sodium stibogluconate (Pentostam) and meglumine antimonate (Glucantime). To test this hypothesis, Leishmania donovani was serially passaged in mice exposed to arsenic in drinking water at environmentally relevant levels (10 or 100 ppm). Arsenic accumulation in organs and other tissues was proportional to the level of exposure and similar to that previously reported in human liver biopsies. After five monthly passages in mice exposed to arsenic, isolated parasites were found to be completely refractory to 500 μg · mL(-1) Pentostam compared with the control passage group (38.5 μg · mL(-1)) cultured in vitro in mouse peritoneal macrophages. Reassessment of resistant parasites following further passage for 4 mo in mice without arsenic exposure showed that resistance was stable. Treatment of infected mice with Pentostam confirmed that resistance observed in vitro also occurred in vivo. We conclude that arsenic contamination may have played a significant role in the development of Leishmania antimonial resistance in Bihar because inadequate treatment with antimonial drugs is not exclusive to India, whereas widespread antimonial resistance is.

  16. Heat-treated Saccharomyces cerevisiae for antimony speciation and antimony(III) preconcentration in water samples

    International Nuclear Information System (INIS)

    An analytical method was developed for antimony speciation and antimony(III) preconcentration in water samples. The method is based on the selective retention of Sb(III) by modified Saccharomyces cerevisiae in the presence of Sb(V). Heat, caustic and solvent pretreatments of the biomass were investigated to improve the kinetics and thermodynamics of Sb(III) uptake process at room temperature. Heating for 30 min at 80 deg. C was defined as the optimal treatment. Antimony accumulation by the cells was independent of pH (5-10) and ionic strength (0.01-0.1 mol L-1). 140 mg of yeast and 2 h of contact were necessary to ensure quantitative sequestration of Sb(III) up to 750 μg L-1. In these conditions, Sb(V) was not retained. Sb(V) was quantified in sorption supernatant by inductively coupled plasma mass spectrometry (ICP-MS) or inductively coupled plasma optical emission spectrometry (ICP-OES). Sb(III) was determined after elution with 40 mmol L-1 thioglycolic acid at pH 10. A preconcentration factor close to nine was achieved for Sb(III) when 100 mL of sample was processed. After preconcentration, the detection limits for Sb(III) and Sb(V) were 2 and 5 ng L-1, respectively, using ICP-MS, 7 and 0.9 μg L-1 using ICP-OES. The proposed method was successfully applied to the determination of Sb(III) and Sb(V) in spiked river and mineral water samples. The relative standard deviations (n = 3) were in the 2-5% range at the tenth μg L-1 level and less than 10% at the lowest Sb(III) and Sb(V) tested concentration (0.1 μg L-1). Corrected recoveries were in all cases close to 100%

  17. Noninferiority of Miltefosine Versus Meglumine Antimoniate for Cutaneous Leishmaniasis in Children

    OpenAIRE

    Rubiano, Luisa Consuelo; Miranda, María Consuelo; Muvdi Arenas, Sandra; Montero, Luz Mery; Rodríguez-Barraquer, Isabel; Garcerant, Daniel; Prager, Martín; Osorio, Lyda; Rojas, Maria Ximena; Pérez, Mauricio; Nicholls, Ruben Santiago; Gore Saravia, Nancy

    2012-01-01

    Background. Children have a lower response rate to antimonial drugs and higher elimination rate of antimony (Sb) than adults. Oral miltefosine has not been evaluated for pediatric cutaneous leishmaniasis.

  18. The influence of pet containers on antimony concentration in bottled drinking water

    OpenAIRE

    Perić-Grujić Aleksandra A.; Radmanovac Aleksandar R.; Stojanov Aleksander M.; Pocajt Viktor V.; Ristić Mirjana Đ.

    2010-01-01

    Antimony trioxide (Sb2O3) is the most frequently used catalyst in the polyethylene terephthalate (PET) manufacture. As a result, antimony is incorporated into PET bottles at concentration level of 100-300 mg/kg. PET containers are used for drinking water and beverages, as well as food packaging and in the pharmaceutical industry. Thus, it is important to understand the factors that may influence the release of antimony from the catalysts into water and other products, since antimony is potent...

  19. The influence of pet containers on antimony concentration in bottled drinking water

    Directory of Open Access Journals (Sweden)

    Perić-Grujić Aleksandra A.

    2010-01-01

    Full Text Available Antimony trioxide (Sb2O3 is the most frequently used catalyst in the polyethylene terephthalate (PET manufacture. As a result, antimony is incorporated into PET bottles at concentration level of 100-300 mg/kg. PET containers are used for drinking water and beverages, as well as food packaging and in the pharmaceutical industry. Thus, it is important to understand the factors that may influence the release of antimony from the catalysts into water and other products, since antimony is potentially toxic trace element. In this paper, the antimony content in nine brands of bottled mineral and spring water from Serbia, and seven brands of bottled mineral and spring water from EU countries was analyzed. The measurements were conducted using the inductively coupled plasma-mass spectrometry (ICP-MS technique. In the all examined samples the antimony concentration was bellow the maximum contaminant level of 5 μg/L prescribed by the Serbian and EU regulations. Comparison of the content of antimony in PET bottled waters with the content of antimony in water bottled commercially in glass and the natural content of antimony in pristine groundwaters, provides explicit evidence of antimony leaching from PET containers. Since waters bottled in PET have much greater concentration ratio of Sb to Pb than corresponding pristine groundwaters, it can be assumed that bottled waters cannot be used as the relavant source for the study of the natural antimony content in groundwaters. There is a clear relation between the quality of water in bottles (composition, ion strength and antimony leaching rate. Moreover, while the rate of antimony leaching is slow at temperatures below 60 oC, at the temperature range of 60-80 oC antimony release occurs and reaches maximum contaminant level rapidly. As antimony can cause both acute and chronic health problems, factors that promote the increase of antimony concentration should be avoided.

  20. Antimony Doped Tin Oxide Thin Films: Co Gas Sensor

    Directory of Open Access Journals (Sweden)

    P.S. Joshi

    2011-01-01

    Full Text Available Tin dioxide (SnO2 serves as an important base material in a variety of resistive type gas sensors. The widespread applicability of this semicoducting oxide is related both to its range of conductance variability and to the fact that it responds to both oxidising and reducing gases. The antimony doped tin-oxide films were prepared by spray pyrolysis method. The as-deposited films are blackish in colour. Addition of antimony impurity showed little increase in the thickness. The X-ray diffraction pattern shows characteristic tin oxide peaks with tetragonal structure. As the doping concentration of antimony was increased, new peak corresponding to Sb was observed. The intensity of this peak found to be increased when the Sb concentration was increased from 0.01 % to the 1 % which indicates the antimony was incorporated into the tin oxide. For gas sensing studies ohmic contacts were preferred to ensure the changes in resistance of sensor is due to only adsorption of gas molecule. The graph of I-V shows a straight line in nature which indicates the ohmic contact. The sensitivity of the sensor for CO gas was tested. The sensitivity of antimony doped tin oxide found to be increased with increasing Sb concentration. The maximum sensitivity was observed for Sb = 1 % at a working temperature of 250 °C.

  1. Behavior of arsenic impurity at antimony electric precipitation

    International Nuclear Information System (INIS)

    In the paper the arsenic impurity electrochemical behavior and it purification from antimony by electric precipitation out of fluoride solutions was studied. For this the arsenic sample with mass 0.003-0.006 g has been irradiated at the WWR-SM nuclear reactor during 3-5 hour in the thermal neutron flux 1013 n/cm2 s, after 24 h keeping the sample has being dissolved in the concentrated nitric acid, and then it has been evaporated several times with distillation water addition up to wet precipitation state. It is shown, that arsenic impurity behavior character in the antimony electric precipitation out to fluoride electrolyte depends on the electrolyte content, electrolysis conditions, arsenic valency state in arsenic impurity existence in the five-valency state its joint electric reduction with antimony is practically not observing. In the case the arsenic being in three-valency state, it joint electric reduction with antimony is taking place. In this time the electrolytic antimony contents arsenic impurities less in dozen time than initial material

  2. Martensite transformation in antimony implanted stainless steel

    International Nuclear Information System (INIS)

    The authors have used Rutherford backscattering analysis (RBS) and transmission electron microscopy (TEM) and diffraction to investigate austenitic stainless steel crystals implanted at room temperature with 80 keV Sb+ ions to a fluence of 5 x 1020 ions/m2, thus providing implantation with a heavy group V element. RBS channeling spectra from implanted crystals show a damage peak which approaches the height of the random level and therefore indicates a very high degree of disorder in the implanted layers. The distribution of the disorder extends to a depth 3-5 times the depth of the primary radiation damage. The Sb peaks under channeling as well as random conditions are indistinguishable, confirming that substitutionality during implantation is negligible. To establish the nature of the disorder which cannot be assessed from the RBS analysis alone, and in particular to assess whether an amorphous alloy is formed in the implanted layer as indicated from the RBS spectra, samples implanted under similar conditions were investigated in the TEM. Significant extra spots in the patterns can be ascribed to the presence of a radiation induced b.c.c. phase of martensitic origin. The result that a significant amount of martensite can be induced by antimony implantation seems to indicate that the main driving force for the transition is due to damage induced stress concentrations. (Auth.)

  3. Antimony Resistance in Leishmania, Focusing on Experimental Research

    Directory of Open Access Journals (Sweden)

    Fakhri Jeddi

    2011-01-01

    Full Text Available Leishmaniases are parasitic diseases that spread in many countries with a prevalence of 12 million cases. There are few available treatments and antimonials are still of major importance in the therapeutic strategies used in most endemic regions. However, resistance toward these compounds has recently emerged in areas where the replacement of these drugs is mainly limited by the cost of alternative molecules. In this paper, we reviewed the studies carried out on antimonial resistance in Leishmania. Several common limitations of these works are presented before prevalent approaches to evidence antimonial resistance are related. Afterwards, phenotypic determination of resistance is described, then confronted to clinical outcome. Finally, we detail molecular mechanisms and targets involved in resistance and already identified in vitro within selected mutant strains or in clinical isolates.

  4. Cyanide and antimony thermodynamic database for the aqueous species and solids for the EPA-MINTEQ geochemical code

    Energy Technology Data Exchange (ETDEWEB)

    Sehmel, G.A.

    1989-05-01

    Thermodynamic data for aqueous species and solids that contain cyanide and antimony were tabulated from several commonly accepted, published sources of thermodynamic data and recent journal article. The review does not include gases or organic complexes of either antimony or cyanide, nor does the review include the sulfur compounds of cyanide. The basic thermodynamic data, ..delta..G/sub f,298//sup o/, ..delta..H/sub f,298//sup o/, and S/sub f//sup o/ values, were chosen to represent each solid phase and aqueous species for which data were available in the appropriate standard state. From these data the equilibrium constants (log K/sub r,298//sup o/) and enthalpies of reaction (..delta..H/sub r,298//sup o/) at 298 K (25/degree/C) were calculated for reactions involving the formation of these aqueous species and solids from the basic components. 34 refs., 14 tabs.

  5. Development and pharmacokinetic of antimony encapsulated in liposomes of phosphatidylserine using radioisotopes in experimental leishmaniasis

    International Nuclear Information System (INIS)

    Leishmaniasis are a complex of parasitic diseases caused by intra macrophage protozoa of the genus Leishmania, and is fatal if left untreated. Pentavalent antimonials, though toxic and their mechanism of action being unclear, remain the first-line drugs for treatment. Effective therapy could be achieved by delivering antileishmanial drugs to these sites of infection. Liposomes are phospholipid vesicles that promote improvement in the efficacy and action of drugs in target cell. Liposomes are taken up by the cells of mononuclear phagocytic system (MPS). The purpose of this study was to develop a preparation of meglumine antimonate encapsulated in liposomes of phosphatidylserine and to study its pharmacokinetic in healthy mice to establish its metabolism and distribution. Quantitative analysis of antimony from liposomes demonstrated that Neutron Activation Analysis was the most sensitive technique with almost 100 % of accuracy. All liposome formulations presented a mean diameter size of 150 nm. The determination of IC50 in infected macrophage showed that liposome formulations were between 10 - 63 fold more effective than the free drug, indicating higher selectivity index. By fluorescence microscopy, an increased uptake of fluorescent-liposomes was seen in infected macrophages during short times of incubation compared with non-infected macrophages. Biodistribution studies showed that meglumine antimonate irradiated encapsulated in liposomes of phosphatidylserine promoted a targeting of antimony for MPS tissues and maintained high doses in organs for a prolonged period. In conclusion, these data suggest that meglumine antimonate encapsulated in liposomes showed higher effectiveness than the non-liposomal drug against Leishmania infection. The development of liposome formulations should be a new alternative for the chemotherapy of infection diseases, especially Leishmaniasis, as they are used to sustain and target pharmaceuticals to the local of infection. (author)

  6. Lattice dynamics of femtosecond laser-excited antimony

    Science.gov (United States)

    Abdel-Fattah, Mahmoud Hanafy; Bugayev, Aleksey; Elsayed-Ali, Hani E.

    2016-07-01

    Ultrafast electron diffraction is used to probe the lattice dynamics of femtosecond laser-excited antimony thin film. The temporal hierarchies of the intensity and position of diffraction orders are monitored. The femtosecond laser excitation of antimony film was found to lead to initial compression after the laser pulse, which gives way to tension vibrating at new equilibrium displacement. A damped harmonic oscillator model, in which the hot electron-blast force contributes to the driving force of oscillations in lattice spacing, is used to interpret the data. The electron-phonon energy-exchange rate and the electronic Grüneisen parameter were obtained.

  7. Heat-treated Saccharomyces cerevisiae for antimony speciation and antimony(III) preconcentration in water samples

    Energy Technology Data Exchange (ETDEWEB)

    Marcellino, Sebastien [Universite de Lyon, Lyon1, Laboratoire des Sciences Analytiques, CNRS UMR 5180, bat CPE, 43, boulevard du 11 novembre 1918, 69622 Villeurbanne cedex (France); Attar, Hossein [Universite Louis Pasteur de Strasbourg, Laboratoire de Chimie Analytique et Sciences Separatives, CNRS UMR 7178, ECPM, 25 rue Becquerel 67087 Strasbourg (France); Lievremont, Didier; Lett, Marie-Claire [Universite Louis Pasteur de Strasbourg, Laboratoire de Genetique Moleculaire, Genetique et Microbiologie, CNRS UMR 7156, 28 rue Goethe, 67000 Strasbourg (France); Barbier, Frederique [CNRS USR 59, Service Central d' Analyse, 59 Chemin du Canal BP22 69390 Vernaison (France); Lagarde, Florence [Universite de Lyon, Lyon1, Laboratoire des Sciences Analytiques, CNRS UMR 5180, bat CPE, 43, boulevard du 11 novembre 1918, 69622 Villeurbanne cedex (France); Universite Louis Pasteur de Strasbourg, Laboratoire de Chimie Analytique et Sciences Separatives, CNRS UMR 7178, ECPM, 25 rue Becquerel 67087 Strasbourg (France)], E-mail: florence.lagarde@univ-lyon1.fr

    2008-11-23

    An analytical method was developed for antimony speciation and antimony(III) preconcentration in water samples. The method is based on the selective retention of Sb(III) by modified Saccharomyces cerevisiae in the presence of Sb(V). Heat, caustic and solvent pretreatments of the biomass were investigated to improve the kinetics and thermodynamics of Sb(III) uptake process at room temperature. Heating for 30 min at 80 deg. C was defined as the optimal treatment. Antimony accumulation by the cells was independent of pH (5-10) and ionic strength (0.01-0.1 mol L{sup -1}). 140 mg of yeast and 2 h of contact were necessary to ensure quantitative sequestration of Sb(III) up to 750 {mu}g L{sup -1}. In these conditions, Sb(V) was not retained. Sb(V) was quantified in sorption supernatant by inductively coupled plasma mass spectrometry (ICP-MS) or inductively coupled plasma optical emission spectrometry (ICP-OES). Sb(III) was determined after elution with 40 mmol L{sup -1} thioglycolic acid at pH 10. A preconcentration factor close to nine was achieved for Sb(III) when 100 mL of sample was processed. After preconcentration, the detection limits for Sb(III) and Sb(V) were 2 and 5 ng L{sup -1}, respectively, using ICP-MS, 7 and 0.9 {mu}g L{sup -1} using ICP-OES. The proposed method was successfully applied to the determination of Sb(III) and Sb(V) in spiked river and mineral water samples. The relative standard deviations (n = 3) were in the 2-5% range at the tenth {mu}g L{sup -1} level and less than 10% at the lowest Sb(III) and Sb(V) tested concentration (0.1 {mu}g L{sup -1}). Corrected recoveries were in all cases close to 100%.

  8. Antimony to Cure Visceral Leishmaniasis Unresponsive to Liposomal Amphotericin B.

    Directory of Open Access Journals (Sweden)

    Gloria Morizot

    2016-01-01

    Full Text Available We report on 4 patients (1 immunocompetent, 3 immunosuppressed in whom visceral leishmaniasis had become unresponsive to (or had relapsed after treatment with appropriate doses of liposomal amphotericin B. Under close follow-up, full courses of pentavalent antimony were administered without life-threatening adverse events and resulted in rapid and sustained clinical and parasitological cure.

  9. Antimony to Cure Visceral Leishmaniasis Unresponsive to Liposomal Amphotericin B.

    Science.gov (United States)

    Morizot, Gloria; Jouffroy, Romain; Faye, Albert; Chabert, Paul; Belhouari, Katia; Calin, Ruxandra; Charlier, Caroline; Miailhes, Patrick; Siriez, Jean-Yves; Mouri, Oussama; Yera, Hélène; Gilquin, Jacques; Tubiana, Roland; Lanternier, Fanny; Mamzer, Marie-France; Legendre, Christophe; Peyramond, Dominique; Caumes, Eric; Lortholary, Olivier; Buffet, Pierre

    2016-01-01

    We report on 4 patients (1 immunocompetent, 3 immunosuppressed) in whom visceral leishmaniasis had become unresponsive to (or had relapsed after) treatment with appropriate doses of liposomal amphotericin B. Under close follow-up, full courses of pentavalent antimony were administered without life-threatening adverse events and resulted in rapid and sustained clinical and parasitological cure.

  10. Discovery of palladium, antimony, tellurium, iodine, and xenon isotopes

    OpenAIRE

    Kathawa, J.; Fry, C; Thoennessen, M

    2012-01-01

    Currently, thirty-eight palladium, thirty-eight antimony, thirty-nine tellurium, thirty-eight iodine, and forty xenon isotopes have been observed and the discovery of these isotopes is discussed here. For each isotope a brief synopsis of the first refereed publication, including the production and identification method, is presented.

  11. The determination of the thermodynamic activity of antimony in alpha-iron

    International Nuclear Information System (INIS)

    In this paper a method is suggested for determining the thermodynamic activity of antimony dissolved in alpha-iron, based on the study of antimony distribution between the two phases: liquid lead and solid iron. By this method, it was found that solid solutions of antimony in alpha-iron can be distinguished by positive divergences from the ideal state. Over a fairly wide range of concentrations, solutions of antimony in iron obey Henry's law. Special experiments on the distribution of antimony between lead and liquid iron showed that in the liquid state also the iron-antimony system is marked by positive divergences from the ideal state when small concentrations of antimony are present. The heat required for the solution of antimony in alpha-iron, and the excess partial molar entropy, were calculated from the activity temperature. The results were used for accurately locating the line showing the solubility limit of antimony in alpha-iron. Since alloys of antimony with iron were obtained by diffusion saturation and not by cooling from the liquid state, there was no liquefaction. Thus the lattice constant of the alloys and its relation to the alloy concentration could be reliably determined. The solubility limit established from X-ray data agrees with that obtained with Sb124. (author)

  12. Antimony and arsenic biogeochemistry in the western Atlantic Ocean

    Science.gov (United States)

    Cutter, Gregory A.; Cutter, Lynda S.; Featherstone, Alison M.; Lohrenz, Steven E.

    The subtropical to equatorial Atlantic Ocean provides a unique regime in which one can examine the biogeochemical cycles of antimony and arsenic. In particular, this region is strongly affected by inputs from the Amazon River and dust from North Africa at the surface, and horizontal transport at depth from high-latitude northern (e.g., North Atlantic Deep Water) and southern waters (e.g., Antarctic Bottom and Intermediate Waters). As a part of the 1996 Intergovernmental Oceanographic Commission's Contaminant Baseline Survey, data for dissolved As(III+V), As(III), mono- and dimethyl arsenic, Sb(III+V), Sb(III), and monomethyl antimony were obtained at six vertical profile stations and 44 sites along the 11,000 km transect from Montevideo, Uruguay, to Bridgetown, Barbados. The arsenic results were similar to those in other oceans, with moderate surface depletion, deep-water enrichment, a predominance of arsenate (>85% As(V)), and methylated arsenic species and As(III) in surface waters that are likely a result of phytoplankton conversions to mitigate arsenate "stress" (toxicity). Perhaps the most significant discovery in the arsenic results was the extremely low concentrations in the Amazon Plume (as low as 9.8 nmol/l) that appear to extend for considerable distances offshore in the equatorial region. The very low concentration of inorganic arsenic in the Amazon River (2.8 nmol/l; about half those in most rivers) is probably the result of intense iron oxyhydroxide scavenging. Dissolved antimony was also primarily in the pentavalent state (>95% antimonate), but Sb(III) and monomethyl antimony were only detected in surface waters and displayed no correlations with biotic tracers such as nutrients and chlorophyll a. Unlike As(III+V)'s nutrient-type vertical profiles, Sb(III+V) displayed surface maxima and decreased into the deep waters, exhibiting the behavior of a scavenged element with a strong atmospheric input. While surface water Sb had a slight correlation with

  13. BioGeochemistry of antimony, Sources, Transfers, Impacts and Assessment

    Science.gov (United States)

    Le Roux, Gael; Pinelli, Eric; Hedde, Mickael; Guiresse, Maritxu; De Vleeschouwer, François; Silvestre, Jérôme; Enrico, Maxime; Gandois, Laure; Monna, Fabrice; Gers, Charles; Probst, Anne

    2013-04-01

    BioGeoSTIB is a project funded by ADEME (French Environmental Protection Agency). Its aim is to provide a better understanding of biogeochemical cycle disturbances of antimony by man. Specifically, it is focused on the atmosphere-soil-organism interfaces. Based on a multi-scale approach, the impact of antimony on organisms and organism communities and the factors of Sb dispersion in the environment aim to better characterized. This report gives the main results of 2 and 1 -2 years of research. Using peat bogs as environmental archives, we show that Sb contamination in soils date back to the beginning of the metallurgy. Atmospheric deposition of Sb largely increased by 100 times during the Industrial Revolution compared to natural levels (~0,001-0,01 mg m-2 an-1) estimated in the deepest peat layers. This disturbance in the antimony geochemical cycle modified its concentrations in soils. One main source of present Sb contamination is automotive traffic due to Sb in braking lines. This emerging contamination was characterized close to a roundabout. This additional source of Sb does not seem to impact soil fauna but Sb concentrations in soil solutions exceed 1 μg L-1. Genotoxicity tests have been performed on the model plant Vicia faba and show that antimony is genotoxic at its lowest concentrations and that there is a synergistic effect lead, a trace metal frequently found in association with antimony in the environment. It is a main issue to determine Sb critical loads in the environment but main identified lacks are thermodynamic data, which are not available yet, to model the behavior of Sb in soil solutions and the fact the antimony is always associated with other anthropogenic trace metals like lead. Critical thresholds of Sb have been determined for the first time based on genotoxicity experiment. Simulations show that these thresholds can be exceeded in the future, whereas present limits for invertebrates (US-EPA) are and will not be reached. However

  14. Monitoring of copper, arsenic and antimony levels in agricultural soils impacted and non-impacted by mining activities, from three regions in Chile.

    Science.gov (United States)

    De Gregori, Ida; Fuentes, Edwar; Rojas, Mariela; Pinochet, Hugo; Potin-Gautier, Martine

    2003-04-01

    This paper reports a comparative study of the concentration of three important environmental elements that are often found together in mineral deposits and then associated with mining activities; copper, arsenic and antimony. These elements were determined in 26 different agricultural soils from regions I, II and V in Chile, zones where the most important and biggest copper industries of this country are located. As background levels of these elements in soils have not been well established, in this study, both, impacted and non-impacted agricultural soils from different regions were considered. The relationships between the concentrations of these elements in soils were also examined. The concentration ranges for copper, arsenic and antimony were 11-530; 2.7-202 and 0.42-11 mg kg(-1) respectively. The copper concentrations in non-polluted soils from the north and central zone of Chile were similar. However, three sites from the north region have copper concentration as higher as 100 mg kg(-1), values that exceed the critical concentration for copper in soils. The concentration of arsenic and antimony in the north soils were higher than in non-impacted ones and, in the case of arsenic, greatly exceeded the world average concentration reported for this element in soils. The highest arsenic and antimony concentrations were found in Calama and Quillagua soils, two different sites in the Loa valley. The arsenic/antimony concentration ratio was higher in Quillagua soil. The high concentrations of three elements determined in impacted soils from region V (Puchuncaví and Catemu valleys) clearly shows the impact produced in this zone by the industrial and mining activities developed in their proximities. At Puchuncaví valley a clear decrease was observed in copper, arsenic and antimony concentrations in soils on the function of the distance from the industrial complex "Las Ventanas", and all concentrations exceeded the reported critical values for this matrix. Instead at

  15. States of antimony and tin atoms in lead chalcogenides

    International Nuclear Information System (INIS)

    It is shown by Mössbauer spectroscopy of the 119Sb(119mSn) isotope that impurity antimony atoms in PbS, PbSe, and PbTe lattices are distributed between cation and anion sublattices. In n-type samples, the greatest part of antimony is located in the anion sublattice; in hole ones, in the cation sublattice. The tin atoms formed as a result of radioactive decay of 119Sb (antisite state) are electrically inactive in the anion sub-lattice of PbS and PbSe, while, in the cation sublattice, they form donor U− centers. Electron exchange between the neutral and doubly ionized tin U− centers via the allowed band states is observed. The tin atoms formed after radioactive decay of 119Sb are electrically inactive in the anion and cation sublattices of PbTe.

  16. 无机锑系阻燃剂%Inorganic Antimony Series Fire Retardants

    Institute of Scientific and Technical Information of China (English)

    张亨

    2012-01-01

    无机锑系阻燃剂主要包括三氧化二锑、五氧化二锑溶胶和锑酸钠等。介绍了它们的性质、生产工艺、产品标准、阻燃用途和研发方向等。%Inorganic antimony series fire retardants include antimony trioxide, antimony pentoxide sol and sodium antimonate, etc. The properties, production process, production standard and uses of several inorganic antimony series fire retardants are introduced.

  17. Correlation of CsK{sub 2}Sb photocathode lifetime with antimony thickness

    Energy Technology Data Exchange (ETDEWEB)

    Mamun, M. A., E-mail: mmamu001@odu.edu; Elmustafa, A. A. [Department of Mechanical and Aerospace Engineering, Old Dominion University, Norfolk, Virginia 23529 (United States); The Applied Research Center, Thomas Jefferson National Accelerator Facility, Newport News, Virginia 23606 (United States); Hernandez-Garcia, C.; Poelker, M. [Thomas Jefferson National Accelerator Facility, Newport News, Virginia 23606 (United States)

    2015-06-01

    CsK{sub 2}Sb photocathodes with quantum efficiency on the order of 10% at 532 nm, and lifetime greater than 90 days at low voltage, were successfully manufactured via co-deposition of alkali species emanating from an effusion source. Photocathodes were characterized as a function of antimony layer thickness and alkali consumption, inside a vacuum chamber that was initially baked, but frequently vented without re-baking. Photocathode lifetime measured at low voltage is correlated with the antimony layer thickness. Photocathodes manufactured with comparatively thick antimony layers exhibited the best lifetime. We speculate that the antimony layer serves as a reservoir, or sponge, for the alkali.

  18. Correlation of CsK2Sb photocathode lifetime with antimony thickness

    Energy Technology Data Exchange (ETDEWEB)

    Mamun, M. A. [Department of Mechanical and Aerospace Engineering, Old Dominion University, Norfolk, Virginia 23529, USA; The Applied Research Center, Thomas Jefferson National Accelerator Facility, Newport News, Virginia 23606, USA; Hernandez-Garcia, C. [Thomas Jefferson National Accelerator Facility, Newport News, Virginia 23606, USA; Poelker, M. [Thomas Jefferson National Accelerator Facility, Newport News, Virginia 23606, USA; Elmustafa, A. A. [Department of Mechanical and Aerospace Engineering, Old Dominion University, Norfolk, Virginia 23529, USA; The Applied Research Center, Thomas Jefferson National Accelerator Facility, Newport News, Virginia 23606, USA

    2015-06-01

    CsK2Sb photocathodes with quantum efficiency on the order of 10% at 532 nm, and lifetime greater than 90 days at low voltage, were successfully manufactured via co-deposition of alkali species emanating from an effusion source. Photocathodes were characterized as a function of antimony layer thickness and alkali consumption, inside a vacuum chamber that was initially baked, but frequently vented without re-baking. Photocathode lifetime measured at low voltage is correlated with the antimony layer thickness. Photocathodes manufactured with comparatively thick antimony layers exhibited the best lifetime. We speculate that the antimony layer serves as a reservoir, or sponge, for the alkali.

  19. Correlation of CsK2Sb photocathode lifetime with antimony thickness

    Directory of Open Access Journals (Sweden)

    M. A. Mamun

    2015-06-01

    Full Text Available CsK2Sb photocathodes with quantum efficiency on the order of 10% at 532 nm, and lifetime greater than 90 days at low voltage, were successfully manufactured via co-deposition of alkali species emanating from an effusion source. Photocathodes were characterized as a function of antimony layer thickness and alkali consumption, inside a vacuum chamber that was initially baked, but frequently vented without re-baking. Photocathode lifetime measured at low voltage is correlated with the antimony layer thickness. Photocathodes manufactured with comparatively thick antimony layers exhibited the best lifetime. We speculate that the antimony layer serves as a reservoir, or sponge, for the alkali.

  20. Resistance to Arsenic- and Antimony-Based Drugs

    OpenAIRE

    Milena Salerno; Arlette Garnier-Suillerot

    2003-01-01

    Organic arsenicals were the first antimicrobial agents specifically synthesized for the treatment of infectious diseases such as syphilis and sleeping sickness. For the treatment of diseases caused by trypanosomatid parasites, organic derivatives of arsenic and the related metalloid antimony are still the drugs of choice. Arsenic trioxide, As203, has been used for a long time in traditional Chinese medicines for treatment of various diseases, and it has recently been shown to be clinically ac...

  1. Crystallization of antimony orthotantalate and its physical properties

    International Nuclear Information System (INIS)

    Physicochemical conditions of monophase synthesis of antimony orthoniobate monocrystals in the system SbO3-Ta2O5-KHF2-H2O2-H2O were investigated. In the area of monophase synthesis of SbTaO4 monocrystals kinetic studies of its growth conditions for inoculation, depending on solvent concentration, temperature, pyroelectric properties of the monocrystal grown were studied and conclusion was made on their practical use

  2. Supermolecular template route to fabrication of well crystallized hollow antimony microspheres

    Institute of Scientific and Technical Information of China (English)

    GU Li; CHEN Shu-da; WEI Xiao-yan

    2006-01-01

    Hollow spheres of elemental antimony (Sb) with good crystallinity, high contrast and thin wall were prepared in the solutions of poly(ethylene glycol) (PEG) and oleic acid(OA) associations at the refluxed temperature. The complexes of Sb3+ with tartaric acid were used as precursors, which can avoid the hydrolysis of SbCl3 and the resulting impurity of products. The average diameter and thickness of the as-prepared hollow sphere are about 300 nm and less than 20 nm, respectively. The formation of hollow spheres depends on the template function of PEG and OA associations, which can be confirmed through the theoretical analysis and results of control experiments. The specific surface area reaches 34.669 m2/g.

  3. Antimony leaching from polyethylene terephthalate (PET) plastic used for bottled drinking water.

    Science.gov (United States)

    Westerhoff, Paul; Prapaipong, Panjai; Shock, Everett; Hillaireau, Alice

    2008-02-01

    Antimony is a regulated contaminant that poses both acute and chronic health effects in drinking water. Previous reports suggest that polyethylene terephthalate (PET) plastics used for water bottles in Europe and Canada leach antimony, but no studies on bottled water in the United States have previously been conducted. Nine commercially available bottled waters in the southwestern US (Arizona) were purchased and tested for antimony concentrations as well as for potential antimony release by the plastics that compose the bottles. The southwestern US was chosen for the study because of its high consumption of bottled water and elevated temperatures, which could increase antimony leaching from PET plastics. Antimony concentrations in the bottled waters ranged from 0.095 to 0.521 ppb, well below the US Environmental Protection Agency (USEPA) maximum contaminant level (MCL) of 6 ppb. The average concentration was 0.195+/-0.116 ppb at the beginning of the study and 0.226+/-0.160 ppb 3 months later, with no statistical differences; samples were stored at 22 degrees C. However, storage at higher temperatures had a significant effect on the time-dependent release of antimony. The rate of antimony (Sb) release could be fit by a power function model (Sb(t)=Sb 0 x[Time, h]k; k=8.7 x 10(-6)x[Temperature ( degrees C)](2.55); Sb 0 is the initial antimony concentration). For exposure temperatures of 60, 65, 70, 75, 80, and 85 degrees C, the exposure durations necessary to exceed the 6 ppb MCL are 176, 38, 12, 4.7, 2.3, and 1.3 days, respectively. Summertime temperatures inside of cars, garages, and enclosed storage areas can exceed 65 degrees C in Arizona, and thus could promote antimony leaching from PET bottled waters. Microwave digestion revealed that the PET plastic used by one brand contained 213+/-35 mgSb/kg plastic; leaching of all the antimony from this plastic into 0.5L of water in a bottle could result in an antimony concentration of 376 ppb. Clearly, only a small

  4. Heavy weight vehicle traffic and its relationship with antimony content in human blood.

    Science.gov (United States)

    Quiroz, Waldo; De Gregori, Ida; Basilio, Paola; Bravo, Manuel; Pinto, Marcela; Lobos, Maria Gabriela

    2009-05-01

    Brake pads systems are nowadays considered as one of the most important sources of antimony in airborne particulate matter. One way that antimony can enter the body is through the lungs and specially by the interaction of antimony with -SH groups present in erythrocyte membrane cells. In spite of that, there are no studies about antimony enrichment in blood of workers exposed to high vehicle traffic. Port workers are generally exposed to heavy weight vehicle traffic. In Chile the biggest marine port is found in Valparaíso City. In this study antimony in whole blood and its fractions (erythrocytes-plasma and erythrocytes membranes-cytoplasm) of 45 volunteers were determined. The volunteers were port workers from Valparaíso city, and two control groups, one from Valparaíso and another from Quebrada Alvarado, the latter being a rural area located about 100 Km away from Valparaíso. The results demonstrate that port workers are highly impacted by antimony emissions from heavy weight vehicle traffic showing an average concentration of 27 +/- 9 ng Sb kg(-1), 5-10 times higher than the concentration of antimony in the blood of control groups. These are the highest antimony levels in blood ever reported in the literature. The highest antimony percentages (>60%) were always found in the erythrocyte fractions. However, the exposure degree to vehicle traffic is significant over antimony distribution in plasma, erythrocytes and cytoplasm. This results shows that the antimony mass in the erythrocyte membranes, was approximately constant at 1.0 +/- 0.1 ng Sb g(-1) of whole blood in all blood samples analyzed.

  5. Tin dioxide sol-gel derived films doped with platinum and antimony deposited on porous silicon

    NARCIS (Netherlands)

    Savaniu, C.; Arnautu, A.; Cobianu, C.; Craciun, G.; Flueraru, C.; Zaharescu, M.; Parlog, C.; Paszti, F.; Berg, van den A.

    1999-01-01

    SnO2 sol-gel derived thin films doped simultaneously with Pt and Sb are obtained and reported for the first time. The Sn sources were tin(IV) ethoxide or tin(II) ethylhexanoate, while hexachloroplatinic acid (H2PtCl6) and antimony chloride (SbCl3) were used as platinum and antimony sources, respecti

  6. Oxidation and mobilization of metallic antimony in aqueous systems with simulated groundwater

    Science.gov (United States)

    Ilgen, A. G.; Majs, F.; Barker, A. J.; Douglas, T. A.; Trainor, T. P.

    2014-05-01

    Antimony (Sb) is a contaminant of concern that can be present in elevated concentrations in shooting range soils due to mobilization from spent lead/antimony bullets. Antimony in shooting range soils has been observed as either metallic Sb(0) or as Sb(V) immobilized by iron (hydr)oxides. The absence of Sb(III) in soils is indicative of rapid Sb(III) oxidation to Sb(V) under surface soil conditions. However, the major controls on antimony oxidation and mobility are poorly understood. To better understand these controls we performed multiple batch experiments under oxic conditions to quantify the oxidation and dissolution of antimony in systems where Sb(0) is oxidized to Sb(III) and further to Sb(V). We also tested how variations in the aqueous matrix composition and the presence of metallic lead (Pb) affect the dissolution, solid phase speciation, and oxidation of antimony. We monitored changes in the aqueous antimony speciation using liquid chromatography inductively coupled plasma mass spectrometry (LC-ICP-MS). To test which solid phases form as a result of Sb(0) oxidation, and therefore potentially limit the mobility of antimony in our studied systems, we characterized the partially oxidized Sb(0) powders by means of extended X-ray absorption fine structure (EXAFS) spectroscopy and powder X-ray diffraction (XRD).

  7. Leishmania donovani: an in vitro study of antimony-resistant amphotericin B-sensitive isolates

    DEFF Research Database (Denmark)

    Sharief, Abdalla Hassan; Gasim Khalil, Eltahir Awad; Theander, Thor G;

    2006-01-01

    Drug sensitivity of clinically antimony-unresponsive Leishmania donovani isolates from Eastern Sudan was evaluated in an in vitro culture system against sodium stibogluconate (Pentostam) and Amphotericin B. Eight isolates, six from antimony-resistant and two from clinically responsive patients were...

  8. Research on Percolation Network and Physical Properties of Graphite/Antimony Composites

    Institute of Scientific and Technical Information of China (English)

    HU Ya-fei; HE Min; WANG Qi-li

    2006-01-01

    The microstructure, friction and wear behaviour of graphite preform and graphite/antimony composites are analysed based on the percolation theory of hydrodynamics to investigate the relationship between the percolation network and physical properties of graphite/antimony composites. The result shows that there are two important factors to enhance friction and wear behaviour of graphite/antimony composites at high temperature: 1) the formation of the pore network in the preform, which is called the first percolation and 2) the optimization of infiltration method in the process of infiltrating antimony, which is called the second percolation. By adding some pyrolysate and controlling the roasting process, perfect net pores and sub-micron percolation microstructure may be formed in the graphite preform. By controlling the infiltration process, the saturation of molten antimony infiltrating into perfect pores can be optimized.

  9. Testing of antimony selective media for treatment of liquid radwaste

    International Nuclear Information System (INIS)

    Nuclear power plants have sought radiation source term reduction and reduced discharge of radioactive constituents for many years. In the case of pressurized water reactors (PWRs), the latter efforts have been directed toward capture and immobilization of recalcitrant (ubiquitous radionuclides with long half-lives) species such as Cs-134 and Cs-137 and Co-58 and Co-60. As these plants resolved, or at least mitigated, the problems with radiocesium and radio-cobalt, antimony radionuclides (Sb-122, Sb-124, and Sb-125) have become a primary concern in liquid liquid radwaste systems Graver Technologies developed a granular composite metal oxide media with good selectivity for radio-antimony. Initial laboratory data were collected using non-radioactive salts of antimony, cesium, and cobalt to judge efficacy of selective removal of antimony. Based on success of those trials, the media, designated Gravex GX187, was tested in partnership with Energy Solutions (nee Duratek) using actual liquid liquid radwaste in two PWR plants. One of these plants performed extensive slip-stream trials comparing the GX187 with strong base anion resins. With more than 2500 bed volumes of throughput, the GX187 outperformed the other competitors by reducing both Sb-124 and Sb-125 radionuclides below minimum detectable activity (MDA) with average decontamination factors (DF's) of 170, even when subjected to high levels of borate. Based on these favorable results, Energy Solutions installed the GX187 in a layered bed in their ALPS liquid radwaste processing system at this plant in August 2005. After one year of intermittent, batchwise operation including an outage, the GX187 processed more than 2.25 million liters (>600,000 gallons) of liquid liquid radwaste while reducing the Sb-125 activity to 2.9 E-08 Bq/L (DF=111) on average. This evaluation is ongoing and will continue at least until the fall 2006 outage at this plant. Concurrently, Graver developed a second generation antimony selective

  10. Enhanced Removal of Arsenic and Antimony in the Mining Site by Calcined γ-Fe2O3/Layered Double Hydroxide Nanocomposite

    Science.gov (United States)

    Lee, Sang-Ho; Choi, Heechul; Kim, Kyoung-Woong

    2016-04-01

    chemical complexation between γ-Fe2O3 and LDH in the nanocomposite. The saturation magnetization of raw γ-Fe2O3 and calcined γ-Fe2O3/LDH nanocomposite were 63.2 and 14.3 emu/g, respectively. Although there was distinct decrease of saturation magnetization of calcined γ-Fe2O3/LDH nanocomposite, the particles were rapidly separated by external magnetic field. The kinetic study revealed that the removal of arsenic and antimony reached equilibrium quickly at about 120 min for initial concentration of 50 mg/L. The regeneration rate of arsenic may retain 70% for five regeneration cycles by 0.5M NaOH with 5M NaCl solution, whereas antimony showed lower regenerability than arsenic due to the higher irreversible fraction in calcined γ-Fe2O3/LDH nanocomposite. Consequently, the effective removal efficiency for arsenic and antimony with its easy magnetic separation makes γ-Fe2O3/LDH nanocomposite be a potential for the field application in the contaminated sites including several mining sites in Korea.

  11. Behavior of ruthenium, cesium and antimony during simulated HLLW vitrification

    International Nuclear Information System (INIS)

    The behavior of ruthenium, cesium, and antimony during the vitrification of simulated high-level radioactive liquid wastes (HLLW) in a liquid fed melter was studied on a laboratory scale and on a semi-pilot scale. In the laboratory melter of a 2.5 kg capacity, a series of tests with the simulate traced with 103Ru, 134Cs and 124Sb, has shown that the Ru and Cs losses to the melter effluent are generally higher than 10% whereas the antimony losses remain lower than 0.4%. A wet purification system comprising in series, a dust scrubber, a condenser, an ejector venturi and an NOx washing column retains most of the activity present in the off-gas so that the release fractions for Ru at the absolute filter inlet ranges between 5.10-3 to 5.10-5% of the Ru fed, for Cs the corresponding release fraction ranges between 3.10-3 to 10-4% and for Sb the release fraction ranges between 1.7 10-4 to 1.7 10-5%. The same experiments were performed at a throughput of 1 to 2 1 h-1 of simulated solution in the semi-pilot scale unit RUFUS. The RUFUS unit comprises a glass melter with a 50 kg molten glass capacity and the wet purification train comprises in series a dust scrubber, a condenser, an ejector venturi and an NOx washing column. The tracer tests were restricted to 103Ru and 134Cs since the laboratory tests had shown that the antimony losses were very low. The results of the tests are presented

  12. Electrostatically defined silicon quantum dots with counted antimony donor implants

    Energy Technology Data Exchange (ETDEWEB)

    Singh, M., E-mail: msingh@sandia.gov; Luhman, D. R.; Lilly, M. P. [Sandia National Laboratories, Albuquerque, New Mexico 87185 (United States); Center for Integrated Nanotechnologies, Sandia National Laboratories, Albuquerque, New Mexico 87175 (United States); Pacheco, J. L.; Perry, D.; Garratt, E.; Ten Eyck, G.; Bishop, N. C.; Wendt, J. R.; Manginell, R. P.; Dominguez, J.; Pluym, T.; Bielejec, E.; Carroll, M. S. [Sandia National Laboratories, Albuquerque, New Mexico 87185 (United States)

    2016-02-08

    Deterministic control over the location and number of donors is crucial to donor spin quantum bits (qubits) in semiconductor based quantum computing. In this work, a focused ion beam is used to implant antimony donors in 100 nm × 150 nm windows straddling quantum dots. Ion detectors are integrated next to the quantum dots to sense the implants. The numbers of donors implanted can be counted to a precision of a single ion. In low-temperature transport measurements, regular Coulomb blockade is observed from the quantum dots. Charge offsets indicative of donor ionization are also observed in devices with counted donor implants.

  13. Antimony implanted strained Si for nMOSFET applications

    OpenAIRE

    Zamani, Atieh

    2009-01-01

    Incorporation of implanted antimony (Sb) in strained-silicon (s-Si) formed on relaxed-SiGe virtual substrates (10 and 30% Ge) has been studied. The implantation doses were 5×1013- 5×1014 cm-2 with an energy of 20 keV. The activation of dopant was performed by an rapid thermal annealing (RTA) treatment at 700 and 800 °C for 30 sec. Projected range of this implantation is about 20 nm which was also confirmed by different techniques. The layers were analyzed in terms of strain relaxation, sheet ...

  14. Solubility behaviour of antimony(III) and antimony(V) solids in basic aqueous solutions at 300{sup o}C

    Energy Technology Data Exchange (ETDEWEB)

    Lemire, R.J.; Tosello, N.B.; Halliday, J.D

    1999-12-01

    The major contributions of the isotopes {sup 122}Sb and {sup 124}Sb to activity transport in a CANDU reactor primary heat transport system (HTS), have been associated with oxygen ingress during reactor shutdown. As part of a program to minimize the release and redeposition of these isotopes, the solubilities of antimony(III) and (V) oxides and salts have been measured in basic solutions at temperatures from 25 to 300{sup o}C. The results provide information on the charge and the stability as a function of temperature of antimony solution species and, hence, a guide to the trends in the temperature dependence of the solubilities of antimony solids. In solutions in which oxidation of antimony(III) to antimony(V) is minimized, the solubility of Sb{sub 2}O{sub 3} increases by about two orders of magnitude between 25 and 200{sup o}C, and then levels out or decreases slightly. At 250{sup o}C, in oxidizing solutions, Sb{sub 2}O{sub 5}{center_dot}xH{sub 2}O and simple sodium antimonate(V) were found to be unstable in sodium hydroxide solutions with respect to the solid, Na{sub 2{alpha}}[H(H{sub 2}O)]{sub 2-2{alpha}}Sb{sub 2}O{sub 6}, which has a pyrochlore structure. The solubility of this partially protonated sodium antimonate increases from 25 to 200{sup o}C and decreases at temperatures above 250{sup o}C. These solubility changes for the antimony (V) solids reflect changes in the stability of the anionic antimony solution species (SbO{sub 3}{sup -} or Sb(OH){sub 6}{sup -}), even though the compositions of antimony-containing solids in basic oxidizing solutions are strongly dependent on the cations and their aqueous phase concentrations. All solids used in the present experiments would be expected to generate total solution antimony concentrations {>=} 0.00005 mol{center_dot}dm{sup -3} in any neutral or basic aqueous solutions (assuming no added sodium salts). Therefore, under HTS conditions, precipitation of any antimony oxides or mixed oxides is unlikely. It cannot be

  15. Antimony removal from the polyethylene terephthalate manufacture wastewater

    Directory of Open Access Journals (Sweden)

    Tomas Vengris

    2010-04-01

    Full Text Available In this study, antimony removal by coagulation from polyethylene terephthalate resin production wastewater of „Orion Global PET“ factory in Klaipėda city was investigated, with regard to the dependence of coagulant type and dosage, pH and presence of organics. FeCl3 ∙6H2O, FeSO4 ∙7H2O, AlCl3∙6H2O and TiCl4 salts were used as coagulants. Ti(IV and Fe(III revealed oneself to be the most effective coagulants. Antimony removal effectiveness is moderate and low using FeSO4 ∙7H2O and AlCl3∙6H2O coagulants, respectively. The addition of 10 mg dm-3 Ti(IV and 30 mg dm-3 Fe(III reduces by ~98% of the Sb, when the initial amount of Sb in wastewater is about 1200 mkg/l. The action of Fe(III is practically independent in the pH range 4-9, and that of Ti(IV slightly decreases in the same pH interval. The Sb amount in wastewater can be reduced to 13-20 mkg dm-3, while the initial Sb concentration is 1200 mkg dm-3. The presence of organic compounds in wastewater determines the reduction of Sb removal by coagulation.

  16. Alkali oxide-tantalum, niobium and antimony oxide ionic conductors

    Science.gov (United States)

    Roth, R. S.; Brower, W. S.; Parker, H. S.; Minor, D. B.; Waring, J. L.

    1975-01-01

    The phase equilibrium relations of four systems were investigated in detail. These consisted of sodium and potassium antimonates with antimony oxide and tantalum and niobium oxide with rubidium oxide as far as the ratio 4Rb2O:llB2O5 (B=Nb, Ta). The ternary system NaSbO3-Sb2O4-NaF was investigated extensively to determine the actual composition of the body centered cubic sodium antimonate. Various other binary and ternary oxide systems involving alkali oxides were examined in lesser detail. The phases synthesized were screened by ion exchange methods to determine mobility of the mobility of the alkali ion within the niobium, tantalum or antimony oxide (fluoride) structural framework. Five structure types warranted further investigation; these structure types are (1) hexagonal tungsten bronze (HTB), (2) pyrochlore, (3) the hybrid HTB-pyrochlore hexagonal ordered phases, (4) body centered cubic antimonates and (5) 2K2O:3Nb2O5. Although all of these phases exhibit good ion exchange properties only the pyrochlore was prepared with Na(+) ions as an equilibrium phase and as a low porosity ceramic. Sb(+3) in the channel interferes with ionic conductivity in this case, although relatively good ionic conductivity was found for the metastable Na(+) ion exchanged analogs of RbTa2O5F and KTaWO6 pyrochlore phases.

  17. Antimony contamination and its effect on Trifolium plants

    Science.gov (United States)

    Corrales, Isabel; Barceló, Juan; Bech, Jaume; Poschenrieder, Charlotte

    2014-05-01

    Antimony is not an essential element and soil Sb contents usually are low.However, soil contamination by Sb has increased in the last years due to the human activities (combustion of fossil fuels, mining, waste incineration, smelting, shooting and road traffic). The main objective of this work was to study the effect of different concentrations of antimony (KSb(OH)6) in order to evaluate the effect on growth and Sb uptake on Trifolium pratense cv. Milvus and Trifolium repens. Our results show that Sb accumulated both in roots and shoots of clover without any negative effect on root growth, cellular viability and lipid peroxidation. This absence of toxicity sympthoms in clover plants could be very dangerous because Sb can be inadvertedly incorporated into the trophic chain causing toxic effects both in animals and humans. The absence of toxic effects on plants does not seem to be due to detoxification by phytochelatins because the use of the gamma-glutamylcysteine synthetase inhibitor, L-buthionine-[S,R]-sulphoximine (BSO) did not enhance Sb toxicity to plants. (Supported by the Spanish MICINN project BFU2010-14873)

  18. Thermal decomposition kinetics of antimony oxychloride in air

    Institute of Scientific and Technical Information of China (English)

    阳卫军; 唐谟堂; 金胜明

    2002-01-01

    The DTA and XRD techniques were employed to study thermal decomposition mechanism of antimony oxychloride SbOCl in the air. The thermal decomposition reaction occurs in four steps, and the former three steps as: SbOCl(s)→Sb4O5Cl2(s)+SbCl3(g)→Sb8O11Cl2(s)+SbCl3(g)→Sb2O3(s)+SbCl3(g). The forth step is the oxidation of Sb2O3 by air, Sb2O3(s)+O2→Sb2O4(s). The activation energy and the order of the thermal decomposition reaction of antimony oxychloride in three steps presented in DTA curves were calculated according to Kinssinger methods from DTA curves. The values of activation energy and the order are respectively 91.97kJ/mol, 0.73 in the first step, 131.14kJ/mol, 0.63 in the second step and 146.94kJ/mol, 1.58 in the third step.

  19. BSA activated CdTe quantum dot nanosensor for antimony ion detection.

    Science.gov (United States)

    Ge, Shenguang; Zhang, Congcong; Zhu, Yuanna; Yu, Jinghua; Zhang, Shuangshuang

    2010-01-01

    A novel fluorescent nanosensor for Sb(3+) determination was reported based on thioglycolic acid (TGA)-capped CdTe quantum dot (QD) nanoparticles. It was the first antimony ion sensor using QD nanoparticles in a receptor-fluorophore system. The water-soluable TGA-capped CdTe QDs were prepared through a hydrothermal route, NaHTe was used as the Te precursor for CdTe QDs synthesis. Bovine serum albumin (BSA) conjugated to TGA-capped CdTe via an amide link interacting with carboxyl of the TGA-capped CdTe. When antimony ion enters the BSA, the lone pair electrons of the nitrogen and oxygen atom become involved in the coordination, switching off the QD emission and a dramatic quenching of the fluorescence intensity results, allowing the detection of low concentrations of antimony ions. Using the operating principle, the antimony ion sensor based on QD nanoparticles showed a very good linearity in the range 0.10-22.0 microg L(-1), with the detection limit lower than 2.94 x 10(-8) g L(-1) and the relative standard deviation (RSD) 2.54% (n = 6). In a study of interferences, the antimony-sensitive TGA-QD-BSA sensor showed good selectivity. Therefore, a simple, fast, sensitive, and highly selective assay for antimony has been built. The presented method has been applied successfully to the determination of antimony in real water samples (n = 6) with satisfactory results.

  20. Removal of cobalt from zinc sulphate solution using rude antimony trioxide as additive

    Institute of Scientific and Technical Information of China (English)

    戴军; 王德全; 姜澜; 金曼

    2002-01-01

    The process of cobalt removal from zinc sulphate solution using rude antimony trioxide as an additive was investigated. The rude antimony trioxide was produced in treatment of copper and lead anode mud and its main components are antimony trioxide, antimony arsenate and lead antimonate. Using the rude antimony trioxide as the additive of cobalt removal can not only decrease operation cost of purification but also find out a new way for utilization of the rude antimony trioxide. The effects of temperature, dosage of zinc dust, the rude antimony trioxide, copper ion and solution pH on removal of cobalt were studied. And experimental data using the rude Sb2O3 as additive were compared with those using Sb2O3. The results indicate that using rude Sb2O3 as additive, cobalt concentration in solution could be decreased from 24mg/L to below 1mg/L under about the same conditions as using Sb2O3.

  1. In Vitro Antiparasitic and Apoptotic Effects of Antimony Sulfide Nanoparticles on Leishmania infantum

    Directory of Open Access Journals (Sweden)

    Saied Soflaei

    2012-01-01

    Full Text Available Visceral leishmaniasis is one of the most important sever diseases in tropical and subtropical countries. In the present study the effects of antimony sulfide nanoparticles on Leishmania infantum in vitro were evaluated. Antimony sulfide NPs (Sb2S5 were synthesized by biological method from Serratia marcescens bacteria. Then the cytotoxicity effects of different concentrations (5, 10, 25, 50, and 100 μg/mL of this nanoparticle were assessed on promastigote and amastigote stages of L. infantum. MTT method was used for verification results of promastigote assay. Finally, the percentages of apoptotic, necrotic, and viable cells were determined by flow cytometry. The results indicated the positive effectiveness of antimony sulfide NPs on proliferation of promastigote form. The IC50 (50% inhibitory concentration of antimony sulfide NPs on promastigotes was calculated 50 μg/mL. The cytotoxicity effect was dose-dependent means by increasing the concentration of antimony sulfide NPs, the cytotoxicity curve was raised and the viability curve of the parasite dropped simultaneously. Moreover, the IC50 of antimony sulfide NPs on amastigote stage was calculated 25 μg/mL. On the other hand, however, antimony sulfide NPs have a low cytotoxicity effect on uninfected macrophages but it can induce apoptosis in promastigote stage at 3 of 4 concentrations.

  2. Segregation of antimony in InP in MOVPE

    Energy Technology Data Exchange (ETDEWEB)

    Weeke, Stefan

    2008-07-01

    In this work the segregation of antimony in indium phosphide in metal organic vapour phase epitaxy (MOVPE)was systematically investigated. Therefore phosphine stabilized InP surfaces were treated with tri-methyl-antimony (TMSb) in MOVPE. An antimony rich Sb/InP surface was established, showing a typical spectra for the antimonides observed in reflectance anisotropy spectroscopy (RAS).Adsorption and desorption of antimony are investigated, as well as the incorporation of Sb during overgrowth of the Sb/InP surface with InP. Therefore the growth parameters temperature, TMSb partial pressure and treatment time are varied and their influence investigated. The experiments are monitored in-situ with RAS, the achieved data is correlated with ex-situ characterisation such as X-ray diffraction (XRD) and secondary ion mass spectroscopy (SIMS). It is shown that under treatment with TMSb a stable Sb/InP surface is formed within seconds, which does not change under further TMSb treatment. This process is rarely influenced by the TMSb partial pressure. On the contrary, the desorption of Sb is a very slow process. Two main processes can be distinguished: The desorption of excess Sb from the surface and the formation of the MOVPE prepared InP (2 x 1) surface. The reaction velocity of adsorption and desorption increases with temperature. Above a critical value the increase of TMSb partial pressure has no influence on the time for desorption. During overgrowth of the Sb/InP surface the opposite temperature dependence is observed: with increasing growth temperature the typical spectra for antimonides is observed longer. An analysis of the grown samples with XRD and SIMS showed the formation of an InPSb double quantum well. One layer is formed at the interface, the second one 50 nm-120 nm deep in the InP. The location of the 2nd InPSb layer can be correlated with the vanishing of the Sb signature in RAS. The distance between the quantum wells increases with growth temperature, until it

  3. A new cloud point extraction procedure for determination of inorganic antimony species in beverages and biological samples by flame atomic absorption spectrometry.

    Science.gov (United States)

    Altunay, Nail; Gürkan, Ramazan

    2015-05-15

    A new cloud-point extraction (CPE) for the determination of antimony species in biological and beverages samples has been established with flame atomic absorption spectrometry (FAAS). The method is based on the fact that formation of the competitive ion-pairing complex of Sb(III) and Sb(V) with Victoria Pure Blue BO (VPB(+)) at pH 10. The antimony species were individually detected by FAAS. Under the optimized conditions, the calibration range for Sb(V) is 1-250 μg L(-1) with a detection limit of 0.25 μg L(-1) and sensitive enhancement factor of 76.3 while the calibration range for Sb(III) is 10-400 μg L(-1) with a detection limit of 5.15 μg L(-1) and sensitive enhancement factor of 48.3. The precision as a relative standard deviation is in range of 0.24-2.35%. The method was successfully applied to the speciative determination of antimony species in the samples. The validation was verified by analysis of certified reference materials (CRMs).

  4. Varicella zoster virus reactivation during or immediately following treatment of tegumentary leishmaniasis with antimony compounds

    Directory of Open Access Journals (Sweden)

    Andrea Barbieri Barros

    2014-07-01

    Full Text Available Antimony compounds are the cornerstone treatments for tegumentary leishmaniasis. The reactivation of herpes virus is a side effect described in few reports. We conducted an observational study to describe the incidence of herpes zoster reactivation during treatment with antimony compounds. The global incidence of herpes zoster is approximately 2.5 cases per 1,000 persons per month (or 30 cases per 1,000 persons per year. The estimated incidence of herpes zoster in patients undergoing antimony therapy is higher than previously reported.

  5. Structural and optical characterization of thermally evaporated bismuth and antimony films for photovoltaic applications

    Science.gov (United States)

    Srimathy, N.; Ruban Kumar, A.

    2016-05-01

    In this present study, the thin film of bismuth and antimony is coated by thermal evaporation system equipped with the inbuilt ultra high vacuum system. XRD analysis confirmed the rhombohedral structure of Bismuth and Antimony on the prepared film. The surface roughness and physical appearance is analyzed by Atomic force microscopy. The results of Raman Spectroscopy show the wave functions and the spectrum of electrons. The preparation technique and conditions strongly influence the crystalline structure and the phase composition of bismuth and antimony thin films. The electrical and optical properties for the prepared film are analyzed. The results show a great interest and promising applications in Photovoltaic devices.

  6. Synthesis and characterisation of nano-pore antimony imprinted polymer and its use in the extraction and determination of antimony in water and fruit juice samples.

    Science.gov (United States)

    Shakerian, Farid; Dadfarnia, Shayessteh; Haji Shabani, Ali Mohammad; Nili Ahmad Abadi, Maryam

    2014-02-15

    A solid phase extraction method using antimony ion imprinted polymer (IIP) sorbent combined with electrothermal atomic absorption spectrometry (ETAAS) was developed for the extraction and speciation of antimony. The sorbent has been synthesised in the presence of Sb(III) and ammonium pyrrolidine dithiocarbamate (APDC) using styrene as the monomer and ethylene glycol dimethacrylate (EGDMA) as the cross linker. The imprinted Sb(III) ions were removed by leaching with HCl (50%v/v) and the polymer was characterised by FT-IR and scanning electron microscopy. The maximum sorption capacity of the IIP for Sb(III) ions was found to be 6.7 mg g(-1). With preconcentration of 60 mL of sample, an enhancement factor of 232 and detection limit of 3.9 ng L(-1) was obtained. Total antimony was determined after the reduction of Sb(V) to Sb(III). The method was successfully applied to the determination of antimony species in water samples and total antimony in fruit juices.

  7. Anthropogenic impacts on the biogeochemistry and cycling of antimony.

    Science.gov (United States)

    Shotyk, William; Krachler, Michael; Chen, Bin

    2005-01-01

    Antimony is a potentially toxic trace element with no known biological function. Antimony is commonly enriched in coals, and fossil fuel combustion appears to be the largest single source of anthropogenic Sb to the global atmosphere. Abundant in sulfide minerals, its emission to the atmosphere from anthropogenic activities is linked to the mining and metallurgy of non-ferrous metals, especially Pb, Cu, and Zn. In particular, the geochemical and mineralogical association of Sb with Pb minerals implies that, like Pb, Sb has been emitted to the environment for thousands of years because of Pb mining, smelting, and refining. In the US alone, there are more than 400 former secondary lead smelting operations and worldwide there are 133 Pb-Zn smelters in operation today. Antimony is used in creating and improving dozens of industrial and commercial materials including various alloys, ceramics, glasses, plastics, and synthetic fabrics, making waste incineration another important source of Sb to the environment. Enrichments of Sb in atmospheric aerosols, plants, soils, sediments, as well as alpine and polar snow and ice suggest that Sb contamination is extensive, but there are very few quantitative studies of the geographic extent, intensity, and chronology of this contamination. There is an urgent need to quantify the extent of human impacts and how these have changed with time. The decreasing inventories of anthropogenic Sb with time in peat cores from Switzerland and Scotland suggest that the atmospheric Sb flux may be declining, but there have been too few studies to make any general conclusions. In fact, some studies of sediments and biomonitors in central Europe show little decline in Sb concentrations during the past decades. There is an obvious need for reliable data from well dated archives such as polar snow and ice, peat bogs, and sediments. The air concentrations, extent of enrichment, particle size distribution, and rate of deposition of Sb in urban areas is

  8. Biogeochemistry of Antimony(V) in Microcosms under Sulfidogenic Conditions

    Science.gov (United States)

    O'Loughlin, E. J.; Johnson, C. R.; Antonopoulos, D. A.; Boyanov, M.; Flynn, T. M.; Koval, J. C.; Kemner, K. M.

    2015-12-01

    As the mining and use of antimony continues to increase, environmental concerns involving the element have grown. Antimony(V) and (III) are the two most environmentally-relevant oxidation states, but little is known about the redox transitions between the two in natural systems. To better understand the behavior of antimony in anoxic environments, we examined the transformations of Sb(V) under Fe(III)- and sulfate-reducing conditions in aqueous suspensions that contained 2 mM KSb(OH)6, 50 mM Fe(III) (as ferrihydrite), 10 mM sulfate, and 10 mM lactate, and were inoculated with sediment from a wetland on the campus of Argonne National Laboratory in Argonne, Illinois. Samples were collected over time to track changes in the concentrations of Sb, Fe(II), sulfate, and lactate, as well as the composition of the microbial community as determined by 16S rRNA gene inventories. We also examined the interaction of Sb(V) with pure Fe(II) mineral phases in aqueous suspensions containing 2 mM KSb(OH)6 and 50 mM Fe(II) as either magnetite, sideritre, vivianite, green rust, or mackinawite. X-ray absorption fine-structure spectroscopy was used to determine the valence state of Sb and its chemical speciation. Lactate was rapidly fermented to acetate and propionate concomittant with a bloom of Veillonellaceae. Utilization of propionate for dissimilatory sulfate reduction (DSR) was accompanied by an increase in Desulfobulbaceae. Sb K-edge X-Ray absorption near edge structure (XANES) analysis showed reduction of Sb(V) to Sb(III) within 4 weeks, concurrent with DSR and the formation of FeS. We observed variable responses in the ability of specific Fe(II) minerals to reduce Sb(V). No reduction was observed with magnetite, siderite, vivianite, or green rust. In the presence of mackinawite (FeS), however, Sb(V) was reduced to Sb(III) sulfide. These results suggest that the reduction of Sb(V) to Sb(III) is not likely under solely Fe(III)-reducing conditions, but is expected in sulfidogenic

  9. A new method for antimony speciation in plant biomass and nutrient media using anion exchange cartridge.

    Science.gov (United States)

    Tisarum, Rujira; Ren, Jing-Hua; Dong, Xiaoling; Chen, Hao; Lessl, Jason T; Ma, Lena Q

    2015-11-01

    A selective separation method based on anion exchange cartridge was developed to determine antimony (Sb) speciation in biological matrices by graphite furnace atomic absorption spectrophotometry (GFAAS). The selectivity of the cartridge towards antimonite [Sb(III)] and antimonate [Sb(V)] reversed in the presence of deionized (DI) water and 2mM citric acid. While Sb(V) was retained by the cartridge in DI water, Sb(III) was retained in citric acid media. At pH 6, Sb(III) and Sb(V) formed Sb(III)- and Sb(V)-citrate complexes, but the cartridge had higher affinity towards the Sb(III)-citrate complex. Separation of Sb(III) was tested at various concentrations in fresh and spent growth media and plant tissues. Our results showed that cartridge-based Sb speciation was successful in plant tissues, which was confirmed by HPLC-ICP-MS. The cartridge retained Sb(III) and showed 92-104% Sb(V) recovery from arsenic hyperaccumulator Pteris vittata roots treated with Sb(III) and Sb(V). The cartridge procedure is an effective alternative for Sb speciation, offering low cost, reproducible results, and simple Sb analysis using GFAAS.

  10. 锡、锑对铅及铅合金中铜元素检测的干扰探究%Detection of Copper Element in Lead and Lead Alloy, the Inquiry of the Interference about Tin,Antimony

    Institute of Scientific and Technical Information of China (English)

    常守森

    2016-01-01

    本文对国家标准(GB/T 74.4———2000)进行了研究。对含高锑、高锡、高锑锡的铅合金中铜含量的测定进行了重点探究。在样品溶解,试样处理以及测定过程三方面加以探究,获得了满意结果。采取先加入助溶络合剂(酒石酸、柠檬酸、Na2EDTA)帮助溶解样品并防止锑、锡水解,然后再分别除去助溶络合剂以及锡、锑等元素的干扰,从而达到准确测定的目的。测定范围:0.00050%~0.60%。%The national standard (GB/T74 .4-2000)was studied . The determination of copper in lead and lead alloy , the influence of high antimony , high tin or high antimony and tin was mainly discussed . Three aspects were explored :dissolve process , operation process and determination process of sample . Satisfac‐tory results had already obtained . Adding hydrotropy complexing agent ( tartaric acid , citric acid , Na2 EDTA) into the sample at first for dissolve the sample and preventing the hydrolysis of antimony or tin , and then to remove hydrotropy complexing agent , the elements such as tin and antimony . It can elim‐inate the influence of tartaric acid , citric acid , Na2 EDTA and the elements such as tin and antimony , thus achieve the purpose of accurate determination . Measuring range is 0 .00050% ~ 0 .60% .

  11. Effect of filler on the self-lubrication performance of graphite antimony composites

    Institute of Scientific and Technical Information of China (English)

    WANG Qi-li; HU Ya-fei; HE Min

    2008-01-01

    Graphite antimony composites were prepared using a mechanical pressure infiltration method to force molten antimony into graphite preforms having a percolation micro-structure and a hop-pocket power filler. The micro-structural and macroscopic properties of the graphite antimony composites were analysed. Observations included metallographic analysis, physical properties and friction and wear behaviour. The results show that the wear loss is decreased by 12.24% and that the friction coefficient is re-duced by 32.61% after hop-pocket power was used. The research indicates that the hop-pocket power method gives a useful way to reduce friction coefficients and wear loss, and to increase service life and self-lubrication properties, of the graphite antimony seal-ing material as compared to carbon black.

  12. Geochemistries of arsenic, antimony, mercury, and related elements in sediments of puget sound

    Science.gov (United States)

    Crecelius, E.A.; Bothner, Michael H.; Carpenter, R.

    1975-01-01

    The natural distributions of arsenic, antimony mercury, chromium, cobalt, iron, aluminum, and carbon in the surface sediments of Puget Sound are perturbed by two major anthropogenic sources of trace metals: a copper smelter near Tacoma, Wash., that discharges large amounts of arsenic and antimony, and a chlor-alkali plant in Bellingham, Wash., which, in the recent past, discharged significant amounts of mercury. Arsenic and antimony inputs from the smelter over the past 80 years are evident in sediment cores whose accumulation rates have been determined by the lead-210 technique. An arsenic budget for Puget Sound reveals the importance of atmospheric input resulting from smokestack emissions of the smelter. Chemical extraction studies of sediments showed that more than 82% of the mercury was associated with easily oxidizable organic matter, whereas about 50% of both arsenic and antimony was associated with extractable iron and aluminum compounds.

  13. NEW THIO S2- ADDUCTS WITH ANTIMONY (III AND V HALIDE: SYNTHESIS AND INFRARED STUDY

    Directory of Open Access Journals (Sweden)

    HASSAN ALLOUCH

    2013-12-01

    Full Text Available Five new S2- adducts with SbIII and SbV halides have been synthesized and studied by infrared. Discrete structures have been suggested, the environment around the antimony being tetrahedral, trigonal bipyramidal or octahedral.

  14. Crystal structure and thermodynamic properties of potassium antimony tungsten oxide

    Energy Technology Data Exchange (ETDEWEB)

    Knyazev, Aleksandr V., E-mail: knav@uic.nnov.ru [Nizhny Novgorod State University, Gagarin Prospekt 23/2, Nizhny Novgorod, 603950 (Russian Federation); Tananaev, Ivan G. [Institute of Physical Chemistry and Electrochemistry, Russian Academy of Sciences, 31 Leninsky prospect, Moscow GSP-1, 119991 (Russian Federation); Kuznetsova, Nataliya Yu.; Smirnova, Nataliya N.; Letyanina, Irene A.; Ladenkov, Igor V. [Nizhny Novgorod State University, Gagarin Prospekt 23/2, Nizhny Novgorod, 603950 (Russian Federation)

    2010-02-20

    In the present work potassium antimony tungsten oxide with pyrochlore structure is refined by the Rietveld method (space group Fd3m, Z = 8). The temperature dependences of heat capacity have been measured for the first time in the range from 7 to 370 K for this compound. The experimental data were used to calculate standard thermodynamic functions, namely the heat capacity C{sub p}{sup o}(T), enthalpy H{sup o}(T) - H{sup o}(0), entropy S{sup o}(T) - S{sup o}(0) and Gibbs function G{sup o}(T) - H{sup o}(0), for the range from T {yields} 0 to 370 K. The differential scanning calorimetry was applied to measure the incongruent melting temperature of compound under study. The high-temperature X-ray diffraction was used for the determining thermal expansion coefficients.

  15. Coherent and Incoherent Structural Dynamics in Laser-Excited Antimony

    CERN Document Server

    Waldecker, Lutz; Bertoni, Roman; Vasileiadis, Thomas; Garcia, Martin E; Zijlstra, Eeuwe S; Ernstorfer, Ralph

    2016-01-01

    We investigate the excitation of phonons in photoexcited antimony and demonstrate that the entire electron-lattice interactions, in particular coherent and incoherent electron-phonon coupling, can be probed simultaneously. Using femtosecond electron diffraction (FED) with high temporal resolution, we observe the coherent excitation of the fully symmetric \\Ag\\ optical phonon mode via the shift of the minimum of the atomic potential energy surface. Molecular dynamics simulations are performed to quantify the change in lattice potential and the associated real-space amplitude of the coherent atomic oscillations. In addition, our experimental configuration allows observing the energy transfer from electrons to phonons via incoherent electron-lattice scattering events. Applying a modified two-temperature model, the electron-phonon coupling is determined from the data as a function of electronic temperature.

  16. Atomistic mechanisms governing structural stability change of zinc antimony thermoelectrics

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Xiaolong [Frontier Institute of Science and Technology, Xi' an Jiaotong University, Xi' an 710054 (China); Lin, Jianping, E-mail: jaredlin@163.com [School of Materials Science and Engineering, Xiamen University of Technology, Xiamen 361024 (China); Qiao, Guanjun [State Key Laboratory for Mechanical Behavior of Materials, Xi' an Jiaotong University, Xi' an 710049 (China); Wang, Zhao, E-mail: zwangzhao@gmail.com [Frontier Institute of Science and Technology, Xi' an Jiaotong University, Xi' an 710054 (China); State Key Laboratory for Mechanical Behavior of Materials, Xi' an Jiaotong University, Xi' an 710049 (China)

    2015-01-05

    The structural stability of thermoelectric materials is a subject of growing importance for their energy harvesting applications. Here, we study the microscopic mechanisms governing the structural stability change of zinc antimony at its working temperature, using molecular dynamics combined with experimental measurements of the electrical and thermal conductivity. Our results show that the temperature-dependence of the thermal and electrical transport coefficients is strongly correlated with a structural transition. This is found to be associated with a relaxation process, in which a group of Zn atoms migrates between interstitial sites. This atom migration gradually leads to a stabilizing structural transition of the entire crystal framework, and then results in a more stable crystal structure of β–Zn{sub 4}Sb{sub 3} at high temperature.

  17. Antimonial drugs entrapped into phosphatidylserine liposomes: physicochemical evaluation and antileishmanial activity

    OpenAIRE

    Samanta Etel Treiger Borborema; João Alberto Osso Junior; Heitor Franco de Andrade Junior; Nanci do Nascimento

    2016-01-01

    Abstract: INTRODUCTION: Leishmaniasis is a disease caused by the protozoan Leishmania that resides mainly in mononuclear phagocytic system tissues. Pentavalent antimonials are the main treatment option, although these drugs have toxic side effects and high resistance rates. A potentially alternative and more effective therapeutic strategy is to use liposomes as carriers of the antileishmanial agents. The aims of this study were to develop antimonial drugs entrapped into phosphatidylserine l...

  18. New low-antimony alloy for straps and cycling service in lead-acid batteries

    Science.gov (United States)

    Prengaman, R. David

    Lead-antimony alloys used for the positive grids in lead-acid batteries for cycling service have generally used antimony contents of 4.5 wt.% and above. Tubular batteries for cycling service that impart high compression of the active material to the grid surface via gauntlet use alloys with antimony contents as low as 1.5 wt.%. These batteries are generally employed in less-severe cycling service. Value-regulated lead-acid (VRLA) batteries can give good cycling service without lead-antimony in the positive grid, but require a high tin content and high compression. The change in automotive battery positive grid alloys to lead-calcium-tin and the tin contents of VRLA positive grids and straps have dramatically increased the tin content of the recycled grid and strap lead in the USA, Europe, and Australia. The higher tin contents can contaminate the lead used for lead-antimony battery grids and generally must be removed to low levels to meet the specifications. This study describes a low-antimony alloy that contains a substantial amount of tin. The high tin content reduces the rate of corrosion of low-antimony positive grid alloys, improves conductivity, increases the bond between the grid and the active material, and cycles as well as the traditional 5-6 wt.% antimony alloys employed in conventional flat-plate batteries. The alloy is also used as a corrosion-resistant cast-on strap alloy for automotive batteries for high temperature service, as well as for posts, bushings, and connectors for all wet batteries.

  19. Effect of Antimony, Phosphorous and Salinity on Growth, Root Membrane Permeability and Root Antimony, Iron and Zinc Concentration of Corn in Hydroponic Media

    OpenAIRE

    H. Barangizi; M. Afyuni; B. Rezaee

    2010-01-01

    Antimony (Sb) pollution has increased in recent years because of human activities and extensive usage of antimony compounds. To date, only a few researches have been conducted in this field in Iran. The purpose of this research is to determine fresh and dry weight, root permeability percentage and root concentration of Sb, Fe and Zn in the corn. This greenhouse research was performed in hydroponics. A factorial experiment (3 × 2 × 3) with three Sb concentrations (0, 6, 18 mgL-1), with and wit...

  20. Effects of antimony on aquatic organisms (Larva and embryo of Oryzias latipes, Moina macrocopa, Simocephalus mixtus, and Pseudokirchneriella subcapitata).

    Science.gov (United States)

    Nam, Sun-Hwa; Yang, Chang-Yong; An, Youn-Joo

    2009-05-01

    Antimony is widespread in aquatic environment. Trivalent forms of antimony are known to be more toxic than other chemical species of antimony. In the present study, antimony potassium tartrate (APT), the trivalent inorganic forms of antimony, was selected as a test antimony compound due to its high water solubility. The effects of antimony on Japanese medaka (Oryzias latipes), planktonic crustacea (Moina macrocopa and Simocephalus mixtus), and green algae (Pseudokirchneriella subcapitata) were evaluated. Larval survival and the embryonic development were measured for fish assay. APT was less toxic to larval medaka (24-h LC50, 261; 48-h LC50, 238 mg L(-1)). Simocephalus mixtus was killed by very low concentrations of APT (24-h LC50, 4.92 mg L(-1)), and antimony was also toxic to Moina macrocopa (24-h LC50, 12.83 mg L(-1)). Toxicities of APT to S. mixtus and Moina macrocopa were about 50 and 20 times more toxic to Oryzias latipes larvae, respectively, in terms of 24-h LC50 value. Growth inhibition of Pseudokirchneriella subcapitata was observed in the presence of APT (72-h EC50, 206 mg L(-1)). This study demonstrated that APT is more toxic to planktonic crustacea than fish and green algae, and planktonic crustacea appears a better indicator of antimony pollution in aquatic environment. PMID:19264343

  1. Adsorption behavior of antimony(III) oxyanions on magnetite surface in aqueous organic acid environment

    Science.gov (United States)

    Mittal, Vinit K.; Bera, Santanu; Narasimhan, S. V.; Velmurugan, S.

    2013-02-01

    Antimony(III) adsorption is observed on magnetite (Fe3O4) surface under acidic and reducing condition through surface hydroxyl (SOH) groups bonding on Fe3O4 surface. Desorption of adsorbed Sb(III) is observed from Fe3O4 surface along with iron release in organic acid at 85 °C after 5 h of experiment. Tartaric acid (TA) shows minimum Sb(III) adsorption on Fe3O4 among the organic acid studied. The reason is TA having two sets of adjacent functional groups viz. Odbnd Csbnd OH and Csbnd OH which are responsible for the formation of five-membered bidendate chelate with Sb(III). Other oxyanions, cations or complexing agents along with TA influences the Sb(III) adsorption on Fe3O4. The surface of magnetite is modified by the addition of fatty acids viz. Lauric acid, benzoic acid to bind the Ssbnd OH groups present on the surface. This results in delaying the process of adsorption without changing the quantity of saturation adsorption of Sb(III) on Fe3O4 surface.

  2. Semiconductor nanocrystals functionalized with antimony telluride zintl ions for nanostructured thermoelectrics.

    Science.gov (United States)

    Kovalenko, Maksym V; Spokoyny, Boris; Lee, Jong-Soo; Scheele, Marcus; Weber, Andrew; Perera, Susanthri; Landry, Daniel; Talapin, Dmitri V

    2010-05-19

    The energy efficiency of heat engines could be improved by the partial recovery of waste heat using thermoelectric (TE) generators. We show the possibility of designing nanostructured TE materials using colloidal inorganic nanocrystals functionalized with molecular antimony telluride complexes belonging to the family of Zintl ions. The unique advantage of using Zintl ions as the nanocrystal surface ligands is the possibility to convert them into crystalline metal chalcogenides, thus linking individual nanobuilding blocks into a macroscopic assembly of electronically coupled functional modules. This approach allows preserving the benefits of nanostructuring and quantum confinement while enabling facile charge transport through the interparticle boundaries. A developed methodology was applied for solution-based fabrication of nanostructured n- and p-type Bi(2-x)Sb(x)Te(3) alloys with tunable composition and PbTe-Sb(2)Te(3) nanocomposites with controlled grain size. Characterization of the TE properties of these materials showed that their Seebeck coefficients, electrical and thermal conductivities, and ZT values compared favorably with those of previously reported solution-processed TE materials.

  3. Complexity

    CERN Document Server

    Gershenson, Carlos

    2011-01-01

    The term complexity derives etymologically from the Latin plexus, which means interwoven. Intuitively, this implies that something complex is composed by elements that are difficult to separate. This difficulty arises from the relevant interactions that take place between components. This lack of separability is at odds with the classical scientific method - which has been used since the times of Galileo, Newton, Descartes, and Laplace - and has also influenced philosophy and engineering. In recent decades, the scientific study of complexity and complex systems has proposed a paradigm shift in science and philosophy, proposing novel methods that take into account relevant interactions.

  4. Arsenic and Antimony Content in Soil and Plants from Baia Mare Area, Romania

    Directory of Open Access Journals (Sweden)

    Gabriela Oprea

    2010-01-01

    Full Text Available Problem statement: The objective of this research was to evaluate the degree of soil contamination with arsenic and antimony in Baia Mare, a nonferrous mining and metallurgical center located in the North West region of Romania. The soil in the area is affected by the emissions of powders containing metals from metallurgical factories. Previous studies indicated the soil contamination with copper, zinc, cadmium and lead, but there is few data about the actual level of soil pollution with arsenic and antimony. Approach: The soil samples were collected from 2 districts of Baia Mare: Ferneziu, which is located in the proximity of a lead smelter and Săsar district which is located along the Sasar River in the preferential direction of the wind over a metallurgical factory producing lead. As reference was considered Dura area located in a less polluted hilly area, in the west part of the town. Samples of soil and plants from the residential area of Ferneziu, Săsar and Dura districts were collected. The arsenic determination was carried out by inductively coupled plasma atomic emission spectrometry and the antimony determination by inductively coupled plasma mass spectrometry. Results: In Ferneziu area, the concentration of arsenic in soil ranged between 0.25 and 255 mg kg-1. In Săsar district the arsenic concentration in the soil ranged between 5.5 and 295 mg kg-1. Regarding antimony, in Ferneziu area the concentration ranged between 5.3 and 40.6 mg kg-1; while in Săsar, antimony soils concentrations vary in the range: 0.9-18.4. Arsenic and antimony concentrations in plants were low for almost of the samples, both in Ferneziu and Săsar area indicating a low mobility of these elements in the studied soils. Conclusion: This study indicated the soil pollution with arsenic both in Ferneziu district and in Săsar district. The soil pollution with antimony was found especially in Ferneziu district.

  5. Antimony distribution and mobility in topsoils and plants (Cytisus striatus, Cistus ladanifer and Dittrichia viscosa) from polluted Sb-mining areas in Extremadura (Spain)

    International Nuclear Information System (INIS)

    A study about topsoil antimony distribution and mobility from the soils to the biomass has been afforded in three abandoned Sb mining areas located at Extremadura. Physico-chemical characteristics of the soils and total antimony levels were measured in soils and autochthonous plant species (Cytisus striatus, Cistus ladanifer and Dittrichia viscosa). Comparison with corresponding values in reference areas isolated from the mining activities is discussed. Antimony mobility in the soils was estimated by measuring the water extractable fraction; low results were obtained for the three soil areas, with no statistical differences. Plant ability to accumulate antimony was estimated by use of plant accumulation coefficients (PAC). Seasonal (spring vs. autumn) effects on the antimony content in the plant species. Cytisus striatus from Mari Rosa mine presented antimony excluder characteristics, whereas Dittrichia viscosa specimens growing in San Antonio mine showed a significant antimony bioaccumulation. - Bioaccumulation of antimony in vegetal species growing in mining areas

  6. Antimony distribution and mobility in topsoils and plants (Cytisus striatus, Cistus ladanifer and Dittrichia viscosa) from polluted Sb-mining areas in Extremadura (Spain)

    Energy Technology Data Exchange (ETDEWEB)

    Murciego, A. Murciego [Area de Cristalografia y Mineralogia, Universidad de Extremadura, Avda. Elvas, s/n, E-06071 Badajoz (Spain); Sanchez, A. Garcia [IRNA-CSIC, Departamento de Geoquimica Ambiental, Aptdo. 257, Salamanca (Spain); Gonzalez, M.A. Rodriguez [Area de Cristalografia y Mineralogia, Universidad de Extremadura, Avda. Elvas, s/n, E-06071 Badajoz (Spain); Gil, E. Pinilla [Departamento de Quimica Analitica y Electroquimica, Facultad de Ciencias, Universidad de Extremadura, Avda. Elvas, s/n, E-06071 Badajoz (Spain)]. E-mail: epinilla@unex.es; Gordillo, C. Toro [Departamento de Quimica Analitica y Electroquimica, Facultad de Ciencias, Universidad de Extremadura, Avda. Elvas, s/n, E-06071 Badajoz (Spain); Fernandez, J. Cabezas [Area de Ecologia, Universidad de Extremadura, Avda. Elvas, s/n, E-06071 Badajoz (Spain); Triguero, T. Buyolo [Area de Ecologia, Universidad de Extremadura, Avda. Elvas, s/n, E-06071 Badajoz (Spain)

    2007-01-15

    A study about topsoil antimony distribution and mobility from the soils to the biomass has been afforded in three abandoned Sb mining areas located at Extremadura. Physico-chemical characteristics of the soils and total antimony levels were measured in soils and autochthonous plant species (Cytisus striatus, Cistus ladanifer and Dittrichia viscosa). Comparison with corresponding values in reference areas isolated from the mining activities is discussed. Antimony mobility in the soils was estimated by measuring the water extractable fraction; low results were obtained for the three soil areas, with no statistical differences. Plant ability to accumulate antimony was estimated by use of plant accumulation coefficients (PAC). Seasonal (spring vs. autumn) effects on the antimony content in the plant species. Cytisus striatus from Mari Rosa mine presented antimony excluder characteristics, whereas Dittrichia viscosa specimens growing in San Antonio mine showed a significant antimony bioaccumulation. - Bioaccumulation of antimony in vegetal species growing in mining areas.

  7. Levels and risk factors of antimony contamination in human hair from an electronic waste recycling area, Guiyu, China.

    Science.gov (United States)

    Huang, Yue; Ni, Wenqing; Chen, Yaowen; Wang, Xiaoling; Zhang, Jingwen; Wu, Kusheng

    2015-05-01

    The primitive electronic waste (e-waste) recycling has brought a series of environmental pollutants in Guiyu, China. Antimony is one of the important metal contaminants and has aroused the global concerns recently. We aimed to investigate concentrations of antimony in human hair from Guiyu and compared them with those from a control area where no e-waste recycling exists, and assessed the potential risk factors. A total of 205 human hair samples from Guiyu and 80 samples from Jinping were collected for analysis. All volunteers were asked to complete a questionnaire including socio-demographic characteristics and other possible factors related to hair antimony exposure. The concentrations of hair antimony were analyzed using atomic absorption spectrophotometer. Our results indicated that the level of hair antimony in volunteers from Guiyu (median, 160.78; range, 6.99-4412.59 ng/g) was significantly higher than those from Jinping (median, 61.74; range, 2.98-628.43 ng/g). The residents who engaged in e-waste recycling activities in Guiyu had higher hair antimony concentrations than others (P < 0.001). There was no significant difference of hair antimony concentrations among different occupation types in e-waste recycling. Multiple stepwise regression analysis indicated that hair antimony concentrations were associated with education level (β = -0.064), the time of residence in Guiyu (β = 0.112), living house also served as e-waste workshop (β = 0.099), the work related to e-waste (β = 0.169), and smoking (β = 0.018). The elevated hair antimony concentrations implied that the residents in Guiyu might be at high risk of antimony contamination, especially the e-waste recycling workers. Work related to e-waste recycling activities and long-time residence in Guiyu contributed to the high hair antimony exposure. PMID:25501644

  8. Predictors of an unsatisfactory response to pentavalent antimony in the treatment of American visceral leishmaniasis

    Directory of Open Access Journals (Sweden)

    Santos Mácia A.

    2002-01-01

    Full Text Available Although treatment of visceral leishmaniasis with pentavalent antimony is usually successful, some patients require second-line drug therapy, most commonly with amphotericin B. To identify the clinical characteristics that predict an inadequate response to pentavalent antimony, a case-control study was undertaken in Teresina, Piaui, Brazil. Over a two-year period, there were 19 cases of VL in which the staff physicians of a hospital prescribed second-line therapy with amphotericin B after determining that treatment with pentavalent antimony had failed. The control group consisted of 97 patients that were successfully treated with pentavalent antimony. A chart review using univariate and multivariate analysis was performed. The cure rate was 90% with amphotericin B. The odds ratio for the prescription of amphotericin B was 10.2 for children less than one year old, compared with individuals aged over 10 years. Patients who presented coinfection had an OR of 7.1 while those on antibiotics had an OR of 2.8. These data support either undertaking a longer course of therapy with pentavalent antimony for children or using amphotericin B as a first-line agent for children and individuals with coinfections. It also suggests that chemoprophylaxis directed toward bacterial coinfection in small children with VL may be indicated.

  9. Arsenic and antimony removal from drinking water by adsorption on granular ferric oxide.

    Science.gov (United States)

    Sazakli, Eleni; Zouvelou, Stavroula V; Kalavrouziotis, Ioannis; Leotsinidis, Michalis

    2015-01-01

    Arsenic and antimony occur in drinking water due to natural weathering or anthropogenic activities. There has been growing concern about their impact on health. The aim of this study was to assess the efficiency of a granular ferric oxide adsorbent medium to remove arsenic and antimony from drinking water via rapid small-scale column tests (RSSCTs). Three different water matrices - deionized, raw water treated with a reverse osmosis domestic device and raw water - were spiked with arsenic and/or antimony to a concentration of 100 μg L⁻¹. Both elements were successfully adsorbed onto the medium. The loadings until the guideline value was exceeded in the effluent were found to be 0.35-1.63 mg g⁻¹ for arsenic and 0.12-2.11 mg g⁻¹ for antimony, depending on the water matrix. Adsorption of one element was not substantially affected by the presence of the other. Aeration did not affect significantly the adsorption capacity. Granular ferric oxide could be employed for the simultaneous removal of arsenic and antimony from drinking water, whereas full-scale systems should be assessed via laboratory tests before their implementation.

  10. Determination of traces of uranium and thorium in antimony(III) oxide by ICP-MS

    International Nuclear Information System (INIS)

    Traces of uranium and thorium in antimony(III) oxide were determined by inductively coupled plasma mass spectrometry (ICP-MS). A method of vaporization as the halide was applied to the separation of the analytes from the antimony matrix. Because the above separation method is so simple, reduced of external contamination was expected. In the case of vaporization using hydrochloric acid, however, it was found that antimony trichloride ions overlapped thorium ion of 232 (m/z). To find the most suitable conditions for matrix separation, vaporization behaviors were studied by using different acidic solutions such as HBr, HBr-HClO4 and HBr-H2SO4. Neither HBr+HClO4 nor HBr+H2SO4 was able to reduce the antimony matrix down to an unaffected level on ICP-MS measurement. On the other hand, in the case of the vaporization using hydrobromic acid, almost all the antimony matrix was removed. Determination limits obtained by this method were 0.02 and 0.03 ng g-1 for uranium and thorium, respectively. (author)

  11. Antimony bioavailability: knowledge and research perspectives for sustainable agricultures.

    Science.gov (United States)

    Pierart, Antoine; Shahid, Muhammad; Séjalon-Delmas, Nathalie; Dumat, Camille

    2015-05-30

    The increasing interest in urban agriculture highlights the crucial question of crop quality. The main objectives for environmental sustainability are a decrease in chemical inputs, a reduction in the level of pollutants, and an improvement in the soil's biological activity. Among inorganic pollutants emitted by vehicle traffic and some industrial processes in urban areas, antimony (Sb) is observed on a global scale. While this metalloid is known to be potentially toxic, it can transfer from the soil or the atmosphere to plants, and accumulate in their edible parts. Urban agriculture is developing worldwide, and could therefore increasingly expose populations to Sb. The objective of this review was in consequences to gather and interpret actual knowledge of Sb uptake and bioaccumulation by crops, to reveal investigative fields on which to focus. While there is still no legal maximal value for Sb in plants and soils, light has to be shed on its accumulation and the factors affecting it. A relative absence of data exists about the role of soil flora and fauna in the transfer, speciation and compartmentation of Sb in vegetables. Moreover, little information exists on Sb ecotoxicity for terrestrial ecosystems. A human risk assessment has finally been reviewed, with particular focus on Sb bioaccessibility.

  12. SESPE-FRAZIER, DIABLO, MATILIJA, DRY LAKES, SAWMILL-BADLANDS, CUYAMA, ANTIMONY, AND QUATAL ROADLESS AREAS, CALIFORNIA.

    Science.gov (United States)

    Frizzell, Virgil A.; Hale, William N.

    1984-01-01

    The study area, consisting of the Sespe-Frazier, Diablo, Matilija, Dry Lakes, Sawmill-Badlands, Cuyama, Antimony, and Quatal Roadless Areas, occupies about 872 sq mi in the Los Padres National Forest, California. Studies indicate that the Sespe-Frazier Roadless Area contains demonstrated resources of gold, gypsum, phosphate and bentonite; deposits in the Cuyama Roadless Area have demonstrated resources of gypsum; mines in the Antimony Roadless Area have demonstrated resources of antimony, gold, silver, and marble; and the Quatal Roadless Area has demonstrated resources of bentonite. The Sespe-Frazier Roadless Area has substantiated potential for geothermal resources suitable for direct-heat purposes, probable and substantiated potential for oil and gas resources, and probable potential for gold resources. Small areas of probable resource potential for antimony and gold were identified in Antimony Roadless Area.

  13. Anodic stripping voltammetry of antimony using gold nanoparticle-modified carbon screen-printed electrodes

    International Nuclear Information System (INIS)

    Carbon screen-printed electrodes (CSPE) modified with gold nanoparticles present an interesting alternative in the determination of antimony using differential pulse anodic stripping voltammetry. Metallic gold nanoparticles deposits have been obtained by direct electrochemical deposition. Scanning electron microscopy measurements show that the electrochemically synthesized gold nanoparticles are deposited in aggregated form. Any undue effects caused by the presence of foreign ions in the solution were also analyzed to ensure that common interferents in the determination of antimony by ASV. The detection limit for Sb(III) obtained was 9.44 x 10-10 M. In terms of reproducibility, the precision of the above mentioned method in %R.S.D. values was calculated at 2.69% (n = 10). The method was applied to determine levels of antimony in seawater samples and pharmaceutical preparations

  14. Synthesis of barium mercaptides and application of antimony/barium mercaptides

    Institute of Scientific and Technical Information of China (English)

    瞿龙; 张露露; 舒万艮

    2001-01-01

    Mercaptoacetic acid, isooctyl thioglycolate and barium hydroxide used as start materials, barium bis (2-ethylhexyl thioglycolate) (Ba(2EHTG)2), barium thioglycolate (Ba(TG)) and barium bisthioglycolate (Ba(TG)2) were synthesized. Their optimum synthetic techniques were discussed, and some physicochemical data were reported. Infrared spectroscopy and elemental analysis methods were used to identify the structures. They were put into PVC plastic products together with antimony tris (2-ethylhexyl thioglycolate) (Sb(2EHTG)3) under the suitable compounding, and their heat stability to PVC was studied. It is shown that these barium mercaptides have remarkable synergisms with antimony mercaptides and the long-term stabilizing effect of organoantimony stabilizer can be effectively improved, reducing the amount of antimony compounds so as to avoid the decrease of its stabilizing effect.

  15. Response of cutaneous leishmaniasis (chiclero's ulcer) to treatment with meglumine antimoniate in Southeast Mexico.

    Science.gov (United States)

    Vargas-Gonzalez, A; Canto-Lara, S B; Damian-Centeno, A G; Andrade-Narvaez, F J

    1999-12-01

    Cutaneous leishmaniasis, known as chiclero's ulcer in southeastern Mexico, is characterized by a predominantly single, painless, ulcerated lesion, without lymphangitis or adenopathy. When located on the ear, it tends to become chronic, causing destruction of the pinna and disfigurement. It is caused predominantly by Leishmania (L.) mexicana. Although pentavalent antimonials (Sb5+) are the mainstay of leishmanial therapy and have been used for more than 50 years, dosage regimens have been repeatedly modified and the best one has not been fully identified. The main purpose of the present study was to investigate the response of chiclero's ulcer to treatment with meglumine antimoniate. One hundred five patients were treated with meglumine antimoniate at a daily dose of 1 ampule per day (425 mg of Sb5+) until healing. The lesions healed after a mean of 25 days (range = 5-60 days). PMID:10674678

  16. Geothermal and fluid flowing simulation of ore-forming antimony deposits in Xikuangshan

    Institute of Scientific and Technical Information of China (English)

    YANG Ruiyan; MA Dongsheng; BAO Zhengyu; PAN Jiayong; CAO Shuanglin; XIA Fei

    2006-01-01

    The Xikuangshan Antimony Deposit located in the Mid-Hunan Basin, China, is the largest antimony deposit in the world. Based on the hydrogeological and geochemical data collected from four sections, Xikuangshan-Dajienao (AO), Xikuangshan-Dashengshan (BO), Xikuangshan-Longshan (CO) and Dafengshan (DO) in the Basin, an advanced metallogenic model related to deep-cyclic meteoric water of Xikuangshan Antimony Deposit is put forward in this paper using a model of heat-gravity-driving fluid flow transportation. The simulation results show that the ore-forming fluid of the deposit mainly comes from the Dashengshan and Longshan areas where BO and CO sections are located if the overall basin keeps a constant atmospheric precipitation and infiltration rate during mineralization, and that the average transportation speed of the ore-forming fluids is about 0.2-0.4 m/a.

  17. Future trends of global atmospheric antimony emissions from anthropogenic activities until 2050

    Science.gov (United States)

    Zhou, Junrui; Tian, Hezhong; Zhu, Chuanyong; Hao, Jiming; Gao, Jiajia; Wang, Yong; Xue, Yifeng; Hua, Shenbin; Wang, Kun

    2015-11-01

    This paper presents the scenario forecast of global atmospheric antimony (Sb) emissions from anthropogenic activities till 2050. The projection scenarios are built based on the comprehensive global antimony emission inventory for the period 1995-2010 which is reported in our previous study. Three scenarios are set up to investigate the future changes of global antimony emissions as well as their source and region contribution characteristics. Trends of activity levels specified as 5 primary source categories are projected by combining the historical trend extrapolation with EIA International energy outlook 2013, while the source-specific dynamic emission factors are determined by applying transformed normal distribution functions. If no major changes in the efficiency of emission control are introduced and keep current air quality legislations (Current Legislation scenario), global antimony emissions will increase by a factor of 2 between 2010 and 2050. The largest increase in Sb emissions is projected from Asia due to large volume of nonferrous metals production and waste incineration. In case of enforcing the pollutant emission standards (Strengthened Control scenario), global antimony emissions in 2050 will stabilize with that of 2010. Moreover, we can anticipate further declines in Sb emissions for all continents with the best emission control performances (Maximum Feasible Technological Reduction scenario). Future antimony emissions from the top 10 largest emitting countries have also been calculated and source category contributions of increasing emissions of these countries present significant diversity. Furthermore, global emission projections in 2050 are distributed within a 1° × 1°latitude/longitude grid. East Asia, Western Europe and North America present remarkable differences in emission intensity under the three scenarios, which implies that source-and-country specific control measures are necessary to be implemented for abating Sb emissions from

  18. Studies on Thin Films of Antimony Vacuum Evaporated from a Knudsen-Type Source

    Directory of Open Access Journals (Sweden)

    K.L. Chaudhary

    2000-10-01

    Full Text Available A Knudsen-type evaporation source was used for the deposition of thin films of antimony to study their growth and microstructure under different rates of evaporation and substrate temperatures when vacuum evaporated onto air-cleaved KC1, mica, amorphous carbon and doped KCl substrates. The crystallisation of these films on exposure to an electron beam of moderate intensity inside the electron microscope was studied, and the orientations of the crystallised films wrt the substrate were established. It has been concluded that antimony films prepared by this source compare well with those prepared by other sources of vacuum evaporation.

  19. Co-doping with antimony to control phosphorous diffusion in germanium

    KAUST Repository

    Tahini, H. A.

    2013-02-15

    In germanium, phosphorous and antimony diffuse quickly and as such their transport must be controlled in order to design efficient n-typed doped regions. Here, density functional theory based calculations are used to predict the influence of double donor co-doping on the migration activation energies of vacancy-mediated diffusion processes. The migration energy barriers for phosphorous and antimony were found to be increased significantly when larger clusters involving two donor atoms and a vacancy were formed. These clusters are energetically stable and can lead to the formation of even larger clusters involving a number of donor atoms around a vacancy, thereby affecting the properties of devices.

  20. Study of ion chromatographic behavior of inorganic and organic antimony species by using inductively coupled plasma mass spectrometric (ICP-MS) detection

    Energy Technology Data Exchange (ETDEWEB)

    Ulrich, N. [University of Hannover, Department of Inorganic Chemistry (Germany)

    1998-04-01

    An on-line method for the analysis of Sb(III), Sb(V) and trimethylstiboxide (TMSbO) is presented. The separation is performed using ion chromatography (IC) on a strong anion-exchange column with phthalic acid plus 2% acteone at pH 5 as mobile phase. The chromatographic system is coupled to an ICP-MS as detector. The influence of different complexing agents on the chromatographic behavior of the antimony species is studied. Rather stable complexes of Sb(III) seem to be formed with citrate and tartrate under the experimental conditions. TMSbO forms a dianionic species with citrate in contrast to the otherwise monoanionic complex. (orig.) With 3 figs., 2 tabs., 8 refs.

  1. Influence of cooling rate and antimony addition content on graphite morphology and mechanical properties of a ductile iron

    Directory of Open Access Journals (Sweden)

    Liu Zhe

    2012-05-01

    Full Text Available Cooling rate and inoculation practice can greatly affect the graphite morphology of ductile irons. In the present research, the effects of the cooling rate and antimony addition on the graphite morphology and mechanical properties of ductile irons have been studied. Three ductile iron castings were prepared through solidification under cooling conditions S (slow, M (medium and F (fast. The cooling rates around the equilibrium eutectic temperature (1,150 ℃ for these cooling conditions (S, M and F were set at 0.21 ℃·min-1, 0.32 ℃·min-1 and 0.37 ℃·min-1, respectively. In addition, four ductile iron castings were prepared by adding 0.01%, 0.02%, 0.03% and 0.04% (by weight antimony, respectively under the slow cooling condition. The results show that the nodularity index, tensile strength and hardness of the ductile iron castings without antimony addition are all improved with the increase of cooling rate, while the ductile iron casting solidified under the medium cooling rate possesses the largest number of graphite nodules. Furthermore, for the four antimony containing castings, the graphite morphology and tensile strength are also improved by the antimony additions, and the effect of antimony addition is intensified when the addition increases from 0.01% to 0.03%. Moreover, the rare earth elements (REE/antimony ratio of 2 appears to be the most effective for fine nodular graphite formation in ductile iron.

  2. Commerce Ministry Announced the Export Quotas for Zinc,Antimony,Tungsten,Tin and Silver

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    <正> The Ministry of Commerce recently announcedits decision on the export quotas for zinc,anti-mony,tungsten,tin and silver in 2004.Accord-ing to the data released,all the export quotasare reduced except for silver.Relevant peoplesay that the raw materials shortage is a majorissue for the production of antimony and tin,

  3. Determination of barium and antimony in gun shot residues by neutron activation analysis

    International Nuclear Information System (INIS)

    The antimony contents on both hands of 7 persons before and after firing an automatic pistol were determined by instrumental neutron activation analysis. The gun shot residues were removed from hands by a 4% solution of cellulose acetate in acetone. The average content of antimony on both hands before firing obtained from 70 measurements (35 from each hand) was 0.040 ± 0.010 micro gram, whereas the average contents on the right and the left hands after 1 firing were 0.385 ± 0.036 and 0.144 ± 0.029 micro gram respectively. The ration of the antimony contents after 1 firing to the normal level (before firing) was 9.9 for the right and 3.6 for the left. No significant difference was observed between male and female, smoker and non-smoker. The antimony content after several firings was not much different from that of 1 firing and it reduced to the normal level within 2 days after firing. The barium contents before and after firing were studied from one person. Barium was precipitated as Ba SO4 before counting. An average contents of 0.936 ± 0.551 micro gram for both hands before firing, 4.092 ± 2.687 micro gram for the right hand and 1.363 ± 0.879 micro gram for the left hand after 1 firing were found

  4. Investigation on the thermal radiation properties of antimony doped tin oxide particles

    Institute of Scientific and Technical Information of China (English)

    Fu Cheng-Wu; Zhang Shuan-Qin; Chen Ming-Qing

    2008-01-01

    This paper reports the preparation of antimony doped tin oxide crystalline powders by chemical coprecipitation method. The influence of sintering temperature and the sintering retention time on the thermal infrared emissivity is analysed. The thermal infrared reflectivity is measured and the optimum doping concentration is proposed.

  5. Thermodynamics for arsenic and antimony in copper matte converting—computer simulation

    Science.gov (United States)

    Chaubal, P. C.; Nagamori, M.

    1988-08-01

    Thermodynamic data for arsenic and antimony and their sulfide and oxide gases have been critically reviewed and compiled. The entropy values for AsS(g), SbS(g), and BiS(g) have been recalculated based on a statistical thermodynamic method. The standard heat of formation and entropy of As2O3(g) have been newly assessed to be △H{298/0} = -81,500 cal/mole and S{298/0} = 81.5 cal/deg/mole. Copper matte converting has been mathematically described using the stepwise equilibrium simulation technique together with quadratic approximations of oxygen and magnetite solubilities in molten mattes. A differential equation for the volatilization of arsenic and antimony has been derived and solved for successive reaction microsteps, whereby the volatilization, slagging, and alloying of the minor elements in copper matte converting have been examined as functions of reaction time and other process variables. Only the first (slag-making) stage of converting is responsible for the elimination of arsenic and antimony by volatilization. Arsenic volatilizes mainly as AsS(g) and AsO(g), with As2(g) also contributing when initial mattes are unusually rich in arsenic (above 0.5 pct arsenic). Antimony volatilizes chiefly as SbS(g), and the contributions of other gases such as SbO(g) and Sb(g) always remain negligibly low. The results of the stepwise equilibrium simulation compare favorably with the industrial operating data.

  6. Antimony production by carbothermic reduction of stibnite in the presence of lime

    Directory of Open Access Journals (Sweden)

    Padilla R.

    2014-01-01

    Full Text Available Experimental work on the carbothermic reduction of Sb2S3 in the presence of lime was carried out in the temperature range of 973 to 1123 K to produce antimony in an environmentally friendly manner. The results demonstrated the technical feasibility of producing antimony by this method without producing SO2 gas. Complete conversion of Sb2S3 was obtained at 1023 K in about 1000 seconds and at 1123 K in less than 250 seconds using stibnite-carbon-lime mixtures with molar ratios Sb2S3:CaO:C = 1:3:3. It was found that the reduction proceeds through the formation of an intermediate oxide SbO2, which is subsequently reduced by CO(g to yield antimony metal and CaS. The kinetics of the Sb2S3 reduction was analyzed by using the equation ln(1-X = -kt. The activation energy was 233 kJ mol-1 in the temperature range of 973 to 1123 K. This value would correspond to an antimony catalyzed carbon oxidation by CO2.

  7. Antimonial drugs entrapped into phosphatidylserine liposomes: physicochemical evaluation and antileishmanial activity

    Directory of Open Access Journals (Sweden)

    Samanta Etel Treiger Borborema

    2016-04-01

    Full Text Available Abstract: INTRODUCTION: Leishmaniasis is a disease caused by the protozoan Leishmania that resides mainly in mononuclear phagocytic system tissues. Pentavalent antimonials are the main treatment option, although these drugs have toxic side effects and high resistance rates. A potentially alternative and more effective therapeutic strategy is to use liposomes as carriers of the antileishmanial agents. The aims of this study were to develop antimonial drugs entrapped into phosphatidylserine liposomes and to analyze their biological and physicochemical characteristics. METHODS: Liposomes containing meglumine antimoniate (MA or pentavalent antimony salt (Sb were obtained through filter extrusion (FEL and characterized by transmission electron microscopy. Promastigotes of Leishmania infantum were incubated with the drugs and the viability was determined with a tetrazolium dye (MTT assay. The effects of these drugs against intracellular amastigotes were also evaluated by optical microscopy, and mammalian cytotoxicity was determined by an MTT assay. RESULTS: Liposomes had an average diameter of 162nm. MA-FEL showed inhibitory activity against intracellular L. infantum amastigotes, with a 50% inhibitory concentration (IC50 of 0.9μg/mL, whereas that of MA was 60μg/mL. Sb-FEL showed an IC50 value of 0.2μg/mL, whereas that of free Sb was 9μg/mL. MA-FEL and Sb-FEL had strong in vitro activity that was 63-fold and 39-fold more effective than their respective free drugs. MA-FEL tested at a ten-times higher concentration than Sb-FEL did not show cytotoxicity to mammalian cells, resulting in a higher selectivity index. CONCLUSIONS: Antimonial drug-containing liposomes are more effective against Leishmania-infected macrophages than the non-liposomal drugs.

  8. Electrodes modified with bismuth, antimony and tin precursor compounds for electrochemical stripping analysis of trace metals (a short review)

    OpenAIRE

    Lezi, Nikolitsa; Economou, Anastasios; Barek, Jiří

    2014-01-01

    Over the last decade, intensive research is being carried out towards the development of “green” electrochemical sensors. Bismuth, antimony and tin electrodes have been proposed as potential substitutes of mercury electrodes in electrochemical stripping analysis of trace metals. The main advantage of these metals as electrode materials is their lower toxicity compared to mercury. Among the different configuration of bismuth, antimony and tin electrodes, one of the most attractive inv...

  9. Investigation into properties of the mixture of perfluoro-2-methyl-bicyclo(4,4,0) decane with antimony fluoride

    International Nuclear Information System (INIS)

    State diagram was constructed for a binary system formed by antimony fluoride and perfluoro-2-methyl-bicyclo-(4,4,0)decane in the temperature range of -58 deg to +56 deg C. Temperature dependence of solubility and the differential molar heat of solubility of solid Sb F5 were determined. Above the melting point of antimony fluoride these components were found to form a system of two sparingly miscible liquids with upper critical dissolution temperature

  10. Electrodeposition of SnSbCu Alloy on Copper from an Electrolyte with Varied Content of Antimony Chloride

    Science.gov (United States)

    Valeeva, A. Kh.; Valeev, I. Sh.

    2015-10-01

    The microstructure and chemical composition of electrodeposited alloys of the SnSbCu system with varied concentration of antimony chloride in the electrolyte have been investigated. It is shown that during electrodeposition mechanical-mixture alloys are not formed, but rather intermetallic compounds. It is found that increasing the concentration of antimony chloride in the electrolyte leads to a decrease in the tin content and cracking of the coating.

  11. The Ministry of Land and Resources Continued to Impose Total Exploitation Control on Tungsten, Antimony and Rare Earth

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    <正>The General Office of the Ministry of Land and Resources distributed "Notice on Issuing Total Exploitation Control Quota of Tungsten Mine, Antimony Mine and Rare Earth Mine (First Batch) for 2013" (the "Notice") on January 5, it issued total exploitation control quota of tungsten mine, antimony mine and rare earth mine (first batch) for 2013. According to the Notice, the first batch of national

  12. Treatment of antimony mine drainage: challenges and opportunities with special emphasis on mineral adsorption and sulfate reducing bacteria.

    Science.gov (United States)

    Li, Yongchao; Hu, Xiaoxian; Ren, Bozhi

    2016-01-01

    The present article summarizes antimony mine distribution, antimony mine drainage generation and environmental impacts, and critically analyses the remediation approach with special emphasis on iron oxidizing bacteria and sulfate reducing bacteria. Most recent research focuses on readily available low-cost adsorbents, such as minerals, wastes, and biosorbents. It is found that iron oxides prepared by chemical methods present superior adsorption ability for Sb(III) and Sb(V). However, this process is more costly and iron oxide activity can be inhibited by plenty of sulfate in antimony mine drainage. In the presence of sulfate reducing bacteria, sulfate can be reduced to sulfide and form Sb(2)S(3) precipitates. However, dissolved oxygen and lack of nutrient source in antimony mine drainage inhibit sulfate reducing bacteria activity. Biogenetic iron oxide minerals from iron corrosion by iron-oxidizing bacteria may prove promising for antimony adsorption, while the micro-environment generated from iron corrosion by iron oxidizing bacteria may provide better growth conditions for symbiotic sulfate reducing bacteria. Finally, based on biogenetic iron oxide adsorption and sulfate reducing bacteria followed by precipitation, the paper suggests an alternative treatment for antimony mine drainage that deserves exploration.

  13. [Physico-chemical characteristics of meglumine antimoniate in different storage conditions].

    Science.gov (United States)

    Romero, G A; de Oliveira, M R; Correia, D; Marsden, P D

    1996-01-01

    During the period October 1992 to July 1995 we measured the osmolarity and pH of ampoules of meglumine antimoniate (glucantime) from lot 9206L-004 (manufactured by Rhodia Farma Ltd, of São Paulo, SP, Brazil) maintained in three temperature conditions namely 4 degrees C, 37 degrees C and ambiental. Although we observed statistically significant differences in osmolarity between samples, the limited number of measurements and the variation of this property in ampoules maintained at the same temperature were obstacles to obtain definitive conclusions. Such a variation was not found with pH. Assuming these parameters could reflect structural changes in the pentavalent antimony molecule, clearly further better controlled experiments are indicated.

  14. Antimony segregation in stressed SiGe heterostructures grown by molecular beam epitaxy

    International Nuclear Information System (INIS)

    The effects of the growth temperature, composition, and elastic strains in separate layers on the segregation of antimony are studied experimentally for stressed SiGe structures grown by molecular beam epitaxy. It is established that the growth conditions and parameters of the structures exert an interrelated influence on the segregation of Sb: the degree of the influence of the composition and elastic stresses in the SiGe layers on Sb segregation depends on the growth temperature. It is shown that usage of a method previously proposed by us for the selective doping of silicon structures with consideration for the obtained dependences of Sb segregation on the growth conditions and parameters of the SiGe layers makes it possible to form SiGe structures selectively doped with antimony

  15. Deciphering lead and cadmium stripping peaks for porous antimony deposited electrodes

    Directory of Open Access Journals (Sweden)

    Taimoor Aqeel Ahmad

    2016-06-01

    Full Text Available Cadmium and lead are generally taken as model heavy metal ions in water to scale the detection limit of various electrode sensors, using electrochemical sensing techniques. These ions interact with the electrochemically deposited antimony electrodes depending on the diffusion limitations. The phenomenon acts differently for the in-situ and ex-situ deposition as well as for porous and non-porous electrodes. A method has been adopted in this study to discourage the stripping and deposition of the working ions (antimony to understand the principle of heavy metal ion detection. X-ray photoelectron spectroscopy (XPS technique was used to establish the interaction between the working and dissolved ions. In addition to the distinct peaks for each analyte, researchers also observed a shoulder peak. A possible reason for the presence of this peak was provided. Different electrochemical tests were performed to ascertain the theory on the basis of the experimental observations.

  16. A facile and fast route to prepare antimony (Sb) nanostructures without additives

    KAUST Repository

    Shah, M.A.

    2011-12-01

    Herein, we report a safe, low cost and reproducible approach for the synthesis of antimony (Sb) nanostructures with most of them having prism like morphology and having well defined faces in the range of ∼70210 nm. The organics free approach is based on a reaction of antimony powder and pure water at ∼210 °C without using any harmful additives and amines. The XRD pattern confirmed the composition and crystallinity of the grown nanostructures. The reported method besides being organics free is economical, fast and free of pollution, which will make it suitable for large scale production. Furthermore, it is well expected that such a technique could be extended to prepare many other important metal and metal oxide nanostructures. The prospects of the process are bright and promising. © 2012 Sharif University of Technology. Production and hosting by Elsevier B.V. All rights reserved.

  17. Bi-antimony capped Keggin polyoxometalate modified with Cu-ligand fragment

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Jiao [College of Chemistry and Material Science, Hebei Normal University, No. 20 Road East of 2nd Ring South, Yuhua District, Shijiazhuang, Hebei 050024 (China); Han, Zhangang, E-mail: hanzg116@yahoo.com.cn [College of Chemistry and Material Science, Hebei Normal University, No. 20 Road East of 2nd Ring South, Yuhua District, Shijiazhuang, Hebei 050024 (China); Zhang, Heng; Yu, Haitao [College of Chemistry and Material Science, Hebei Normal University, No. 20 Road East of 2nd Ring South, Yuhua District, Shijiazhuang, Hebei 050024 (China); Zhai, Xueliang, E-mail: xlzhai253@mail.hebtu.edu.cn [College of Chemistry and Material Science, Hebei Normal University, No. 20 Road East of 2nd Ring South, Yuhua District, Shijiazhuang, Hebei 050024 (China)

    2012-10-15

    Three polyoxometalates consisting of bi-antimony capped Keggin-type clusters: [Cu(mbpy){sub 2}]{sub 2}[PMo{sub 12}O{sub 40}Sb{sub 2}]{center_dot}4H{sub 2}O (1), [Cu(mbpy){sub 2}][PMo{sub 12}O{sub 40}Sb{sub 2}] (2) and {l_brace}Cu(mbpy)[Cu(mbpy){sub 2}]{sub 2}{r_brace}[VMo{sub 8}V{sub 4}O{sub 40}Sb{sub 2}]{center_dot}2H{sub 2}O (3) (mbpy=4,4 Prime -dimethyl-2,2 Prime - dipyridyl in 1 and 2; 5,5 Prime -dimethyl-2,2 Prime -dipyridyl in 3) have been synthesized and characterized by IR, X-ray powder diffraction, TG analysis and electrochemical property. Single-crystal analysis revealed that all of three compounds are built upon bi-antimony capped Keggin-type polyoxoanions and Cu-mbpy cations. In 1-3, two Sb{sup III} centers located at the two opposite of anionic surface adopt fundamentally tetragonal pyramidal coordination geometry. Both compounds 1 and 2 consist of P-centered Keggin structure, while compound 3 presents a V-centered Keggin anion. The Keggin-type anions present different structural features: isolated cluster in 1 and Cu-ligand-supported cluster in 2 and 3. - Graphical abstract: Three hybrid compounds consisting of bi-antimony capped Keggin-type clusters modified with Cu-ligand cations have been synthesized and characterized. Highlights: Black-Right-Pointing-Pointer Three hybrid compounds consisting of bi-antimony capped Keggin-type clusters have been synthesized. Black-Right-Pointing-Pointer Two Sb{sup III} centers located at the two opposite of anionic surface adopt tetragonal pyramidal coordination geometry. Black-Right-Pointing-Pointer The anions present different structural features: isolated and Cu-ligand-supported cluster.

  18. Metal corrosion studies with the fluorosulphonic acid-antimony pentafluoride superacid system

    International Nuclear Information System (INIS)

    Because of their rapid dissolution of many actinide metals and refractory oxides, superacids such as HSO3F/SbF5 have potential applications in actinide processing. However, material compatibility must first be addressed because of the highly corrosive nature of superacids. This paper describes the qualitative rates of attack of fluorosulphonic acid-antimony pentafluoride superacid on a variety of metal substrates relevant to nuclear processing

  19. Application of Hyphenated Techniques in Speciation Analysis of Arsenic, Antimony, and Thallium

    OpenAIRE

    Rajmund Michalski; Sebastian Szopa; Magdalena Jabłońska; Aleksandra Łyko

    2012-01-01

    Due to the fact that metals and metalloids have a strong impact on the environment, the methods of their determination and speciation have received special attention in recent years. Arsenic, antimony, and thallium are important examples of such toxic elements. Their speciation is especially important in the environmental and biomedical fields because of their toxicity, bioavailability, and reactivity. Recently, speciation analytics has been playing a unique role in the studies of biogeochemi...

  20. Vortex-assisted surfactant-enhanced emulsification microextraction based on solidification of floating organic drop followed by electrothermal atomic absorption spectrometry for speciation of antimony (ΙΙΙ, V).

    Science.gov (United States)

    Eftekhari, Mohammad; Chamsaz, Mahmoud; Arbab-Zavar, Mohammad Hossein; Eftekhari, Ali

    2015-01-01

    Vortex-assisted surfactant-enhanced emulsification microextraction based on solidification of floating organic drop (VASEME-SFO) was used for preconcentration and speciation of antimony (ΙΙΙ, V) followed by electrothermal atomic absorption spectrometry (ETAAS). In this procedure, Triton X-114 was used as emulsifier and 1-undecanol was used as extraction solvent. This method is based on the complexation of Sb(ΙΙΙ) with dithizone (as complexing agent) at pH 2 and extraction of the resulting hydrophobic complex into the extraction solvent (1-undecanol) with vortex-assisted liquid phase microextraction, whereas Sb(V) remained in solution. Sb(ΙΙΙ) in extraction solvent was directly analyzed by ETAAS after dilution with ethanol, and Sb(V) was calculated by subtracting Sb(ΙΙΙ) from the total antimony after reducing Sb(V) to Sb(ΙΙΙ) by L-cysteine. Under the optimized condition, the calibration curve was linear in the range of 0.4-8 μg L(-1) of Sb(ΙΙΙ) with a correlation coefficient of 0.9995. The detection limit based on three times of the standard deviation of the blank (n = 8) was 0.09 μg L(-1). The validation and the recovery of the proposed method were performed by the analysis of a certified reference material and spike method. The obtained results were in very good agreements with certified values. The proposed method was successfully applied for the determination of antimony species at trace levels in different water samples. PMID:25404541

  1. Studies in atomic-fluorescence spectroscopy-V The fluorescence characteristics and determination of antimony.

    Science.gov (United States)

    Dagnall, R M; Thompson, K C; West, T S

    1967-10-01

    Atomic-fluorescence of antimony may be generated in an air-propane flame by nebulizing aqueous solutions of antimony salts whilst irradiating the flame by means of a microwave-excited electrode-less discharge tube operating at 30 W. The strongest fluorescence is exhibited by the (4)S(11 2 ) --> (4)P(1 3 ) 2311 A resonance line and weaker signals are observed at the 2068 and 2176 A resonance lines and at four intercombination lines, at 2598, 2671, 2770 and 2878 A. A process of thermally assisted direct-line fluorescence is postulated to account for the otherwise inexplicable intensity of the 2598 A line emission. Atomic-fluorescence spectroscopy at 2176 A permits the determination of antimony in the range 0.1-120 ppm with a detection limit of 0.05 ppm. With the same equipment and source, the range of measurement for atomic-absorption was 6-120 ppm and the detection limit was 1 ppm. No interferences were observed from 100-fold molar amounts of Cd, Co, Cu, Fe, Hg, K, Mg, Mn, Mo, Na, NH(4), Pb and Zn or from arsenate, chloride, nitrate, phosphate and sulphate. PMID:18960212

  2. Morphology and antimony segregation of spangles on batch hot-dip galvanized coatings

    International Nuclear Information System (INIS)

    Spangles produced by batch hot-dip galvanizing process have a rougher surface and a greater surface segregation of alloying element compared with those in continuous hot-dip galvanizing line (CGL), owing to the cooling rate of the former is much smaller than that of the later. Therefore, typical spangles on a batch hot-dipped Zn-0.05Al-0.2Sb alloy coating were investigated. The chemical, morphological characterization and identification of the phases on the spangles were examined by scanning electron microscopy (SEM), backscattered electron imaging (BSE), atomic force microscopy (AFM), energy dispersive spectroscopy (EDS) and X-ray diffraction analysis (XRD). The results showed that the coating surface usually exhibited three kinds of spangles: shiny, feathery and dull spangle, of which extensively antimony surface segregation was detected. The nature of precipitate on the coating surface was identified as β-Sb3Zn4, The precipitated β-Sb3Zn4 particles distributed randomly on the shiny spangle surface, both β-Sb3Zn4 particles and dentritic segregation of antimony dispersed in the dendritic secondary arm spacings of the feathery spangle and on the whole dull spangle surface. The dentritic segregation of antimony and precipitation of Sb3Zn4 compound are discussed by a proposed model.

  3. Antimony in the Contaminated Site of El Triunfo, Baja California Sur, Mexico

    Directory of Open Access Journals (Sweden)

    Marmolejo-Rodríguez A. J.

    2013-04-01

    Full Text Available Antimony has properties similar to arsenic with some of its compounds toxic to humans. Therefore it is necessary to control the wastes accumulated by anthropogenic activities, such as mining, where it is in tailings to be released to the environment. According to the Environment Protection Agency, the maximum value in sediments is 11.2 mg Sb kg–1 and the Earth’s crust average is 0.2 mg Sb kg–1. In this semiarid area, the drainage basin El Carrizal is impacted with wastes of an abandoned gold mine at the Mining District El Triunfo (MD – ET which have tailings with 17,600 mg kg–1 of antimony. In the main dry river (arroyo, the Sb content is between 0.6 and 122 mg kg–1. This element is transported from the source throughout the fluvial basin to discharge into the Pacific Ocean. In the arroyo mouth we collected one sedimentary core and the sediment from dunes (28.6 – 45.7 and 6.43 – 7.74 mg Sb kg–1. This research concluded the antimony is enriched in this semiarid system, with Normalized Enrichment Factors severely enriched mainly in arroyo sediments close to the MD-ET

  4. Parto prematuro após uso de antimonial pentavalente: relato de um caso Premature birth after the use of pentavalent antimonial: case report

    Directory of Open Access Journals (Sweden)

    Bruna Pinheiro Silveira

    2003-07-01

    Full Text Available Relata-se o caso de uma mulher de 19 anos, na 24ª semana de gravidez e com leishmaniose visceral. Tratada com antimonial pentavalente na posologia de 850mg/dia por 20 dias, ocorreu parto prematuro no quinto dia de tratamento e óbito da criança um dia após nascimento. Considerando a importância da protozoose no nosso meio e a raridade da associação com a gestação, julgamos de interesse a publicação do caso.A case is reported of a 19-year-old woman, at week 24 of gestation, with visceral leishmaniosis. She was treated with meglumine antimoniate at a dose of 850mg/day for 20 days. There occurred premature birth on day five of treatment and the neonate died one day after birth. Considering the importance of protozoiasis in our population and the rarity of the association with pregnancy, we resolved to publish the case.

  5. Comparison of oral itraconazole and intramuscular meglumine antimoniate in the treatment of cutaneous leishmaniasis

    International Nuclear Information System (INIS)

    To compare the efficacy and tolerability of oral itraconazole against intramuscular meglumine antimoniate in the treatment of Cutaneous Leishmaniasis (CL). Two hundred eligible and consenting patients of Cutaneous Leishmaniasis (CL) were divided in two groups with 100 patients in each. The number and location of the lesions were documented and clinical types of cutaneous leishmaniasis were noted. The diagnosis was confirmed by skin slit smear and histopathology of the lesional skin. Culture on Nicolle Novy MacNeal (NNN) medium and Leishmanin test was done in all patients. All the patients in both groups were subjected to complete blood picture, urine examination, serum urea and creatinine levels and ECG examination. One group was given itraconazole 100 mg twice daily orally for a duration of 6-8 weeks. The other group was given meglumine antimoniate 10 cc in the form of deep intramuscular injections for 15-30 days. The efficacy of the treatment was judged by clinical and parasitological response. Side effects of the agents were also noted during treatment. Out of 200 patients studied, 185 were males and 15 were females. The mean age of presentation was 30 + 6.6 years. Single lesion was seen in 132 (66%) subjects whereas 68 (34%) subjects had multiple lesions. Slit skin smears were positive in 50 (25%) of the patients. Skin biopsy yielded the presence of LT bodies in 150 (75%) subjects. The culture was positive in 102 (51%) cases. Leishmanin test was positive in 94% subjects. Seventy-five (75%) patients on itraconazole therapy showed complete clinical and parasitological cure in 4-8 weeks duration. A rise in ALT was seen in 12% subjects. Five (5%) subjects did not show any improvement till the end of therapy. Sixty-five (65%) subjects on meglumine antimoniate showed complete healing in 15-30 days. In 35 (35%) of the patients, the treatment had to be stopped due to intolerable side-effects. Four cases of lupoid leishmaniasis and 4 cases of sporotrichoid leishmaniasis

  6. Development of an analytical method for antimony speciation in vegetables by HPLC-hydride generation-atomic fluorescence spectrometry.

    Science.gov (United States)

    Olivares, David; Bravo, Manuel; Feldmann, Jorg; Raab, Andrea; Neaman, Alexander; Quiroz, Waldo

    2012-01-01

    A new method for antimony speciation in terrestrial edible vegetables (spinach, onions, and carrots) was developed using HPLC with hydride generation-atomic fluorescence spectrometry. Mechanical agitation and ultrasound were tested as extraction techniques. Different extraction reagents were evaluated and optimal conditions were determined using experimental design methodology, where EDTA (10 mmol/L, pH 2.5) was selected because this chelate solution produced the highest extraction yield and exhibited the best compatibility with the mobile phase. The results demonstrated that EDTA prevents oxidation of Sb(III) to Sb(V) and maintains the stability of antimony species during the entire analytical process. The LOD and precision (RSD values obtained) for Sb(V), Sb(III), and trimethyl Sb(V) were 0.08, 0.07, and 0.9 microg/L and 5.0, 5.2, and 4.7%, respectively, for a 100 microL sample volume. The application of this method to real samples allowed extraction of 50% of total antimony content from spinach, while antimony extracted from carrots and onion samples ranged between 50 and 60 and 54 and 70%, respectively. Only Sb(V) was detected in three roots (onion and spinach) that represented 60-70% of the total antimony in the extracts. PMID:22970588

  7. Development of an analytical method for antimony speciation in vegetables by HPLC-hydride generation-atomic fluorescence spectrometry.

    Science.gov (United States)

    Olivares, David; Bravo, Manuel; Feldmann, Jorg; Raab, Andrea; Neaman, Alexander; Quiroz, Waldo

    2012-01-01

    A new method for antimony speciation in terrestrial edible vegetables (spinach, onions, and carrots) was developed using HPLC with hydride generation-atomic fluorescence spectrometry. Mechanical agitation and ultrasound were tested as extraction techniques. Different extraction reagents were evaluated and optimal conditions were determined using experimental design methodology, where EDTA (10 mmol/L, pH 2.5) was selected because this chelate solution produced the highest extraction yield and exhibited the best compatibility with the mobile phase. The results demonstrated that EDTA prevents oxidation of Sb(III) to Sb(V) and maintains the stability of antimony species during the entire analytical process. The LOD and precision (RSD values obtained) for Sb(V), Sb(III), and trimethyl Sb(V) were 0.08, 0.07, and 0.9 microg/L and 5.0, 5.2, and 4.7%, respectively, for a 100 microL sample volume. The application of this method to real samples allowed extraction of 50% of total antimony content from spinach, while antimony extracted from carrots and onion samples ranged between 50 and 60 and 54 and 70%, respectively. Only Sb(V) was detected in three roots (onion and spinach) that represented 60-70% of the total antimony in the extracts.

  8. Responses and acclimation of Chinese cork oak (Quercus variabilis Bl.) to metal stress: the inducible antimony tolerance in oak trees.

    Science.gov (United States)

    Zhao, Xiulian; Zheng, Lingyu; Xia, Xinli; Yin, Weilun; Lei, Jingpin; Shi, Shengqing; Shi, Xiang; Li, Huiqing; Li, Qinghe; Wei, Yuan; Chang, Ermei; Jiang, Zeping; Liu, Jianfeng

    2015-08-01

    Antimony (Sb) pollution has become a pressing environmental problem in recent years. Trees have been proven to have great potential for the feasible phytomanagement; however, little is known about Sb retention and tolerance in trees. The Chinese cork oak (Quercus variabilis Bl.) is known to be capable of growth in soils containing high concentrations of Sb. This study explored in detail the retention and acclimation of Q. variabilis under moderate and high external Sb levels. Results revealed that Q. variabilis could tolerate and accumulate high Sb (1623.39 mg kg(-1) DW) in roots. Dynamics of Sb retention in leaves, stems, and roots of Q. variabilis were different. Leaf Sb remained at a certain level for several weeks, while in roots and stems, Sb concentrations continued to increase. Sb damaged tree's PSII reaction cores but elicited defense mechanism at the donor side of PSII. It affected the electron transport flow after QA (-) more strongly than the oxygen-evolving complex and light-harvesting pigment-protein complex II. Sb also decreased leaf chlorophyll concentrations and therefore inhibited plant growth. During acclimation to Sb toxicity, Sb concentrations in leaves, stems, and roots decreased, with photosynthetic activity and pigments recovering to normal levels by the end of the experiment. These findings suggest that Sb tolerance in Q. variabilis is inducible. Acclimation seems to be related to homeostasis of Sb in plants. Results of this study can provide useful information for trees breeding and selection of Sb phytomanagement strategies, exploiting the established ability of Q. variabilis to transport, delocalize in the leaves, and tolerate Sb pollutions.

  9. Leachability of antimony from energy ashes. Total contents, leachability and remedial suggestions; Lakning av antimon fraan energiaskor. Totalhalter, lakbarhet samt foerslag till aatgaerder

    Energy Technology Data Exchange (ETDEWEB)

    Baeckstroem, Mattias [Oerebro Univ. (Sweden)

    2006-01-15

    In the current project total concentrations for antimony in 31 energy ashes have been compiled. The average concentration of antimony in boiler fly ash and grate boiler fly ash is 192 and 1,140 mg/kg, respectively. The corresponding antimony concentrations for boiler ashes and grate bottom ashes are 86,5 and 61,8 mg/kg, respectively. Multivariate calculations clearly pointed out waste as the major source for antimony in ashes. The difference between total antimony concentration in fly ash and bottom ash is greatest for grate boilers, in average 18 times higher in the fly ash. The difference for CFB/BFB-boilers is only slightly more than 2. However, based on amount, 75% of the total antimony inventory is recovered in the fly ashes for both CFB/BFB and grate boilers. Eleven (eight of which were bottom ashes) out of the 31 samples exceeded the guidelines for inert waste. It is clear that the higher ionic strength in the solutions from the fly ashes contribute to decrease the solubility for critical minerals retaining antimony. In addition, the fly ashes have considerably larger effective surface able to sorb trace elements. A clear and positive covariance was discovered between aluminium and antimony. Furthermore, it was noted that antimony showed no typical anionic behaviour despite the fact that it according to the geochemical calculations should be present as SbO{sub 3}{sup -}. At L/S 10, a maximum of 1% of the total antimony concentration is leached. This should be compared to chloride that had 94% of the total concentration leached at L/S 10. There was no correlation between the leached antimony concentrations and the total antimony concentrations. The sequential extractions also suggest a low leachability for antimony from the ashes. In average only 9,6% is released at pH 7, 7,3% at pH 5, 3,6% during reducing conditions and 3,2% during oxidising conditions. In total, only 24% of the total antimony concentrations is released during the four extraction steps. The

  10. Synthesis, characterization and single crystal X-ray analysis of chlorobis(N,N-dimethyldithiocarbamato-S,S′antimony(III

    Directory of Open Access Journals (Sweden)

    H.P.S. Chauhan

    2015-07-01

    Full Text Available The title compound chlorobis(N,N-dimethyldithiocarbamato-S,S′antimony(III has been prepared in distilled acetonitrile and characterized by physicochemical [melting point and molecular weight determination, elemental analysis (C, H, N, S & Sb], spectral [FT–IR, far IR, NMR (1H & 13C] studies. The crystal and molecular structure was further confirmed using single crystal X-ray diffraction analysis which features a five-coordinate geometry for antimony(III within a ClS4 donor set. The distortion in the co-planarity of ClSbS3 evidences the stereochemical influence exerts by the lone pair of electrons on antimony(III. Two centrosymmetrically related molecule held together via C–H···Cl secondary interaction result in molecular aggregation of the compound.

  11. Selective liquid-liquid extraction of antimony(III from hydrochloric acid media by N-n-octylaniline in xylene

    Directory of Open Access Journals (Sweden)

    M. A. ANUSE

    2004-04-01

    Full Text Available N-n-Octylaniline in xylene was used for the extraction separation of antimony(III from hydrochloric acid media. Antimony(III was extracted quantitatively with 10 mL 4 % N-n-octylaniline in xylene. It was stripped from the organic phase with 0.5 M ammonia and estimated photometrically by the iodide method. The effect of metal ion, acid, reagent concentration and various foreign ions was investigated. The method affords binary and ternary separation of antimony(III from tellurium(IV, selenium(IV, lead(II, bismuth(III, tin(IV, germanium(IV, copper(II, gold(III, iron(III and zinc(II. The method is applicable for the analysis of synthetic mixtures, alloys and semiconductor thin films. It is fast, accurate and precise.

  12. Lithium-antimony-lead liquid metal battery for grid-level energy storage

    Science.gov (United States)

    Wang, Kangli; Jiang, Kai; Chung, Brice; Ouchi, Takanari; Burke, Paul J.; Boysen, Dane A.; Bradwell, David J.; Kim, Hojong; Muecke, Ulrich; Sadoway, Donald R.

    2014-10-01

    The ability to store energy on the electric grid would greatly improve its efficiency and reliability while enabling the integration of intermittent renewable energy technologies (such as wind and solar) into baseload supply. Batteries have long been considered strong candidate solutions owing to their small spatial footprint, mechanical simplicity and flexibility in siting. However, the barrier to widespread adoption of batteries is their high cost. Here we describe a lithium-antimony-lead liquid metal battery that potentially meets the performance specifications for stationary energy storage applications. This Li||Sb-Pb battery comprises a liquid lithium negative electrode, a molten salt electrolyte, and a liquid antimony-lead alloy positive electrode, which self-segregate by density into three distinct layers owing to the immiscibility of the contiguous salt and metal phases. The all-liquid construction confers the advantages of higher current density, longer cycle life and simpler manufacturing of large-scale storage systems (because no membranes or separators are involved) relative to those of conventional batteries. At charge-discharge current densities of 275 milliamperes per square centimetre, the cells cycled at 450 degrees Celsius with 98 per cent Coulombic efficiency and 73 per cent round-trip energy efficiency. To provide evidence of their high power capability, the cells were discharged and charged at current densities as high as 1,000 milliamperes per square centimetre. Measured capacity loss after operation for 1,800 hours (more than 450 charge-discharge cycles at 100 per cent depth of discharge) projects retention of over 85 per cent of initial capacity after ten years of daily cycling. Our results demonstrate that alloying a high-melting-point, high-voltage metal (antimony) with a low-melting-point, low-cost metal (lead) advantageously decreases the operating temperature while maintaining a high cell voltage. Apart from the fact that this finding

  13. The LABCG2 Transporter from the Protozoan Parasite Leishmania Is Involved in Antimony Resistance.

    Science.gov (United States)

    Perea, Ana; Manzano, José Ignacio; Castanys, Santiago; Gamarro, Francisco

    2016-06-01

    Treatment for leishmaniasis, which is caused by Leishmania protozoan parasites, currently relies on a reduced arsenal of drugs. However, the significant increase in the incidence of drug therapeutic failure and the growing resistance to first-line drugs like antimonials in some areas of Northern India and Nepal limit the control of this parasitic disease. Understanding the molecular mechanisms of resistance in Leishmania is now a matter of urgency to optimize drugs used and to identify novel drug targets to block or reverse resistant mechanisms. Some members of the family of ATP-binding cassette (ABC) transporters in Leishmania have been associated with drug resistance. In this study, we have focused our interest to characterize LABCG2's involvement in drug resistance in Leishmania. Leishmania major parasites overexpressing the ABC protein transporter LABCG2 were generated in order to assess how LABCG2 is involved in drug resistance. Assays of susceptibility to different leishmanicidal agents were carried out. Analysis of the drug resistance profile revealed that Leishmania parasites overexpressing LABCG2 were resistant to antimony, as they demonstrated a reduced accumulation of Sb(III) due to an increase in drug efflux. Additionally, LABCG2 was able to transport thiols in the presence of Sb(III) Biotinylation assays using parasites expressing LABCG2 fused with an N-terminal green fluorescent protein tag revealed that LABCG2 is partially localized in the plasma membrane; this supports data from previous studies which suggested that LABCG2 is localized in intracellular vesicles that fuse with the plasma membrane during exocytosis. In conclusion, Leishmania LABCG2 probably confers antimony resistance by sequestering metal-thiol conjugates within vesicles and through further exocytosis by means of the parasite's flagellar pocket. PMID:27021316

  14. Development and pharmacokinetic of antimony encapsulated in liposomes of phosphatidylserine using radioisotopes in experimental leishmaniasis; Desenvolvimento e farmacocinetica de antimonio encapsulado em lipossomas de fosfatidilserina utilizando radioisotopos em leishmaniose experimental

    Energy Technology Data Exchange (ETDEWEB)

    Borborema, Samanta Etel Treiger

    2010-07-01

    Leishmaniasis are a complex of parasitic diseases caused by intra macrophage protozoa of the genus Leishmania, and is fatal if left untreated. Pentavalent antimonials, though toxic and their mechanism of action being unclear, remain the first-line drugs for treatment. Effective therapy could be achieved by delivering antileishmanial drugs to these sites of infection. Liposomes are phospholipid vesicles that promote improvement in the efficacy and action of drugs in target cell. Liposomes are taken up by the cells of mononuclear phagocytic system (MPS). The purpose of this study was to develop a preparation of meglumine antimonate encapsulated in liposomes of phosphatidylserine and to study its pharmacokinetic in healthy mice to establish its metabolism and distribution. Quantitative analysis of antimony from liposomes demonstrated that Neutron Activation Analysis was the most sensitive technique with almost 100 % of accuracy. All liposome formulations presented a mean diameter size of 150 nm. The determination of IC{sub 50} in infected macrophage showed that liposome formulations were between 10 - 63 fold more effective than the free drug, indicating higher selectivity index. By fluorescence microscopy, an increased uptake of fluorescent-liposomes was seen in infected macrophages during short times of incubation compared with non-infected macrophages. Biodistribution studies showed that meglumine antimonate irradiated encapsulated in liposomes of phosphatidylserine promoted a targeting of antimony for MPS tissues and maintained high doses in organs for a prolonged period. In conclusion, these data suggest that meglumine antimonate encapsulated in liposomes showed higher effectiveness than the non-liposomal drug against Leishmania infection. The development of liposome formulations should be a new alternative for the chemotherapy of infection diseases, especially Leishmaniasis, as they are used to sustain and target pharmaceuticals to the local of infection. (author)

  15. Highly active and stable Pt electrocatalysts promoted by antimony-doped SnO2 supports for oxygen reduction reactions

    DEFF Research Database (Denmark)

    Yin, Min; Xu, Junyuan; Li, Qingfeng;

    2014-01-01

    Alternative composite supports for platinum catalysts were synthesized from antimony doped tin dioxide (ATO) nanoparticles. In the range of the antimony content from 0 to 11mol%, the highest electrical conductivity of 1.1Scm-1 at 130°C was obtained for the 5mol% Sb ATO, from which composite...... supports composed of oxides and carbon and supported platinum catalysts were prepared. Using the pure oxide support, the Pt/ATO catalyst displayed superior specific activity and stability for the oxygen reduction reactions (ORRs). Low surface area of ATO caused poor dispersion of Pt particles compared...

  16. Separation of antimony from synthetic cloth. Application in forensic science using neutron activation analysis

    International Nuclear Information System (INIS)

    A simple ion-exchange separation procedure was developed for selective removal of antimony from synthetic cloth to facilitate determination of several trace elements frequently used to identify gunshot residues by neutron activation analysis. Radiotracers of Sb, Ba, Cu, Co, As, Zn, Hg and Ag were employed to optimize the developed procedure. The method involves the quantitative retention of the above elements, except of Sb, from 0.2M ammonium carbonate solution using Chelex 100 resin and subsequent quantitative elution of the elements of interest with 2M nitric acid for gamma-ray spectrometry. The procedure was tested by simulated gunshot residues. (author)

  17. Influence of arsenic,antimony and cobalt impurities on the cathodic process in zinc electrowinning

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    By means of an electrochemical study,the influence of arsenic,antimony and cobalt on cathodic polarization in the zinc electrowinning process,the associated kinetic equations and parameters,and the polarization mechanism have been studied.The results show that the experimental values of the kinetic parameters are in accord with the theoretical values in the ZnSO4/H2SO4 solution with a single impurity is added.In contrast,the charge transfer coefficient α is smaller than the theoretical value in the ZnSO4/H2SO4 solution when the three impurities are added together.

  18. Polymorphism and properties of Bi{sub 2}WO{sub 6} doped with pentavalent antimony

    Energy Technology Data Exchange (ETDEWEB)

    Kharitonova, E.P.; Belov, D.A. [M.V. Lomonosov Moscow State University, Leninskie Gory, 119991 Moscow (Russian Federation); Gagor, A.B.; Pietraszko, A.P. [W. Trzebiatowski Institute of Low Temperature and Structure Research, Polish Academy of Sciences, Okólna 2, 50-950 Wrocław (Poland); Alekseeva, O.A. [Shubnikov Institute of Crystallography, Russian Academy of Sciences, Leninsky pr. 59, 119333 Moscow (Russian Federation); Voronkova, V.I., E-mail: voronk@polly.phys.msu.ru [M.V. Lomonosov Moscow State University, Leninskie Gory, 119991 Moscow (Russian Federation)

    2014-04-05

    Highlights: • The limit of Bi{sub 2}W{sub 1−x}Sb{sub x}O{sub 6−y} solid solutions is at x = 0.05. • Bi{sub 2}W{sub 1−x}Sb{sub x}O{sub 6−y} does not fully transform into high-temperature monoclinic phase. • Sb{sup 5+} has a weak effect on the temperatures of the ferroelectric transitions. • γ→γ{sup ‴} transition near 650 °C was observed as strong permittivity peak at 0.01–8 Hz. • The conductivity of Bi{sub 2}W{sub 0.96}Sb{sub 0.04}O{sub 6−y} at 800 °C reaches 0.02 S/cm. -- Abstract: Antimony-containing solid solutions isostructural with bismuth tungstate, Bi{sub 2}WO{sub 6}, have been prepared in air as polycrystalline samples by solid-state reactions and as single crystals by unseeded flux growth. The antimony in the solid solutions is in a pentavalent state and substitutes for tungsten in the structure of Bi{sub 2}WO{sub 6}. The Bi{sub 2}W{sub 1−x}Sb{sub x}O{sub 6−y} solid solutions have been shown to exist in the composition range 0 ⩽ x ⩽ 0.05. We have examined the effect of Sb{sup 5+} doping on the polymorphism and properties of Bi{sub 2}WO{sub 6}. In contrast to undoped Bi{sub 2}WO{sub 6}, antimony-substituted bismuth tungstate does not completely transform into its high-temperature, monoclinic phase at 960 °C and remains two-phase up to temperatures approaching its melting point. Antimony substitution for tungsten has a weak effect on the temperatures of the ferroelectric phase transitions. Heterovalent substitution of Sb{sup 5+} for W{sup 6+} is accompanied by the formation of extra oxygen vacancies and an increase in the electrical conductivity of the solid solutions by one to two orders of magnitude relative to undoped Bi{sub 2}WO{sub 6}.

  19. Electromagnetic absorption and shielding behavior of polyaniline-antimony oxide composites

    Science.gov (United States)

    Faisal, Muhammad; Khasim, Syed

    2013-02-01

    This work highlights the microwave absorption and electromagnetic interference (EMI) shielding properties of synthesized polyaniline (PAni)-antimony oxide (Sb2O3) composites in the 8-12 GHz (X-band) range. These composites showed absorption dominated EMI shielding effectiveness (EMI SEA) of -34 to -40 dB (> 99 % attenuation), indicating their shielding potential throughout the X-band. Our analyses reveal that the Sb2O3 particles in PAni matrix have key impact in determining the microwave absorption properties of the composites.

  20. Determination of arsenic, selenium and antimony by neutron activation analysis. Application to hair samples

    International Nuclear Information System (INIS)

    A fast rabbit system for instrumental activation analysis with reactor neutrons is described. Its use in the determination of selenium in hair is discussed. A survey is given of the correction factors which are inherent to the use of short-lived radionuclides. An alternative to INAA is NAA based on the separation of arsenic, selenium and antimony by hydride evaporation and adsorption to active carbon. Data for some Standard Reference Materials are given. This work was done under research contract 2440/RI/RB with the IAEA

  1. Migration and leaching risk of extraneous antimony in three representative soils of China: lysimeter and batch experiments.

    Science.gov (United States)

    Hou, H; Yao, N; Li, J N; Wei, Y; Zhao, L; Zhang, J; Li, F S

    2013-11-01

    Antimony (Sb) distribution, solubility and mobility onto natural soils of China were studied in lysimeter and batch experiments as a function of physicochemical properties of the soil. An outdoor lysimeter experiment investigated the leaching and migration of Sb in the soils with Sb-polluted topsoil and unpolluted subsoil over a 5month period. Soil solutions were collected by suction cups installed at different depth of lysimeters, and leachates were regularly collected and analyzed for Sb concentrations. The majority of the added Sb was retained in the topsoil layers, but small portions were moved to the sub-layers. Sb concentrations in the soil solutions and leachates ranged from 0-755.5 (6.38±54 on average) μg l(-1) and 0-0.45 (smaller than the detection limit) μg l(-1) respectively, indicating the low solubility of Sb in the soils. Batch experiments were performed in order to determine the sorption capacity and the partition coefficient (Kd). Freundlich isotherm described properly the equilibrium experimental data and results show that the Kd values for Primosol, Isohumosol, Ferrosol equal to 22.5, 87.8, 704 L kg(-1), respectively. These results showed the strong capacity of the soils to retain Sb, and prevent it being leached down the profile. The mobilizable Sb was in the order: Primosol>Isohumosol>Ferrosol. Sb migration in the soils was mainly associated with the exchangeable, carbonate-bound, and metal-organic complex-bound fractions. Health risk assessment indicates that Sb leaching from Ferrosol will not harm to human health through groundwater under the test conditions, while it has certain health risks from the Isohumosol and Primosol. PMID:23931906

  2. High levels of antimony in dust from e-waste recycling in southeastern China

    International Nuclear Information System (INIS)

    Environmental contamination due to uncontrolled e-waste recycling is an emerging global issue. Antimony (Sb) is a toxic element used in semiconductor components and flame retardants for circuit board within electronic equipment. When e-waste is recycled, Sb is released and contaminates the surrounding environment; however, few studies have characterized the extent of this problem. In this study, we investigated Sb and arsenic (As) distributions in indoor dust from 13 e-waste recycling villages in Guiyu, Guangdong Province, southeastern China. Results revealed significantly elevated concentrations of Sb (6.1-232 mg/kg) in dust within all villages, which were 3.9-147 times higher than those from the non e-waste sites, indicating e-waste recycling was an important source of Sb pollution. On the contrary, As concentrations (5.4-17.7 mg/kg) in e-waste dusts were similar to reference values from the control sites. Therefore, dusts emitted from e-waste recycling may be characterized by high Sb/As ratios, which may help identify the contamination due to the e-waste recycling activities. - Highlights: → Antimony and arsenic concentrations in dust from e-waste recycling were investigated. → E-waste recycling is an important emerging source of Sb pollution. → Sb/As ratios may help identify the e-waste contamination.

  3. Canine visceral leishmaniasis: comparison of in vitro leishmanicidal activity of marbofloxacin, meglumine antimoniate and sodium stibogluconate.

    Science.gov (United States)

    Vouldoukis, Ioannis; Rougier, Sandrine; Dugas, Bernard; Pino, Paco; Mazier, Dominique; Woehrlé, Frédérique

    2006-01-30

    The control of canine leishmaniasis largely depends on the success of treatment. Drugs currently available to treat this disease are toxic and partially effective. The curative effect of marbofloxacin, a third-generation fluoroquinolone developed for veterinarian individual treatment, was evaluated in vitro in the presence of Leishmania infantum promastigotes and dog-monocyte-derived macrophages; meglumine antimoniate and sodium stibogluconate were used as comparative treatments. We observed that the killing of Leishmania promastigotes and intracellular amastigotes by marbofloxacin was dose-dependent. We demonstrated that successful treatment of canine infected macrophages for 48 h was possible with 500 microg/ml of marbofloxacin. Leishmanicidal activity acted through a TNF-alpha and nitric oxide pathway and correlated with the generation of nitric oxide (NO(2)) production by monocytes derived macrophages from infected (23+/-5 microM) or healthy (21+/-6 microM) dogs, in comparison with NO(2) concentration in infected/non-treated macrophages (Marbofloxacin was shown to be non-toxic at 500 microg/ml in vitro and no cell apoptosis was observed. The molecule was able to induce a parasitic process after significant elimination of amastigotes in leishmania-infected dog macrophages. We propose that marbofloxacin, compared to standard chemotherapeutic agents (meglumine antimoniate and sodium stibogluconate), could be an effective and pragmatic oral route alternative to treat canine leishmaniasis.

  4. Evaluation of antimony microparticles supported on biochar for application in the voltammetric determination of paraquat.

    Science.gov (United States)

    Gevaerd, Ava; de Oliveira, Paulo R; Mangrich, Antonio S; Bergamini, Márcio F; Marcolino-Junior, Luiz H

    2016-05-01

    This work describes the construction and application of carbon paste electrodes modified with biochar and antimony microparticles (SbBCPE) for voltammetric determination of paraquat using a simple and sensitive procedure based on voltammetric stripping analysis. Some parameters such as amount of biochar and antimony used in the composition of the carbon paste and instrumental parameters were examined in detail. Under optimized conditions, an analytical curve was obtained for paraquat determination employing SbBCPE, which showed a linear response ranging from 0.2 to 2.9 μmol L(-1), with limit of detection and quantification of 34 nmol L(-1) and 113 nmol L(-1), respectively, after paraquat pre-concentration of 120 s. The repeatability study presented a RSD=2.0% for 10 consecutive measurements using the same electrode surface and the reproducibility study showed a RSD=2.7% for measurements with 10 different electrode surfaces. The proposed sensor was successfully applied for paraquat determination in tap water and citric fruit juice spiked samples and good recoveries were obtained without any sample pre-treatment, showing its promising analytical performance.

  5. Antimony retention and release from drained and waterlogged shooting range soil under field conditions.

    Science.gov (United States)

    Hockmann, Kerstin; Tandy, Susan; Lenz, Markus; Reiser, René; Conesa, Héctor M; Keller, Martin; Studer, Björn; Schulin, Rainer

    2015-09-01

    Many soils polluted by antimony (Sb) are subject to fluctuating waterlogging conditions; yet, little is known about how these affect the mobility of this toxic element under field conditions. Here, we compared Sb leaching from a calcareous shooting range soil under drained and waterlogged conditions using four large outdoor lysimeters. After monitoring the leachate samples taken at bi-weekly intervals for >1.5 years under drained conditions, two of the lysimeters were subjected to waterlogging with a water table fluctuating according to natural rainfall water infiltration. Antimony leachate concentrations under drained conditions showed a strong seasonal fluctuation between 110 μg L(-1) in summer and soil solution indicated that this decrease in Sb(V) concentrations was attributable to the reduction of Sb(V) to Sb(III) and the stronger sorption affinity of the latter to iron (Fe) (hydr)oxide phases. Our results demonstrate the importance of considering seasonal and waterlogging effects in the assessment of the risks from Sb-contaminated sites. PMID:25592464

  6. A Black Phosphate Conversion Coating on Steel Surface Using Antimony(III)-Tartrate as an Additive

    Science.gov (United States)

    Li, Feng; Wang, Guiping

    2016-05-01

    A novel black phosphate conversion coating was formed on steel surface through a Zn-Mn phosphating bath containing mainly ZnO, H3PO4, Mn(H2PO4)2, and Ca(NO3)2, where antimony(III)-tartrate was used as the blackening agent of phosphatization. The surface morphology and composition of the coating were characterized by scanning electron microscopy, energy dispersion spectroscopy, and x-ray photoelectron spectroscopy. Corrosion resistance of the coating was studied by potentiodynamic polarization curves and electrochemical impedance spectroscopy. The pH value of the solution had significant influence on the formation and corrosion resistance of the coating. The experimental results indicated that the Sb plays a vital role in the blackening of phosphate conversion coating. The optimal concentration of antimony(III)-tartrate in the phosphating bath used in this experiment was 1.0 g L-1, as higher values reduced the corrosion resistance of the coating. In addition, by saponification and oil seals, the corrosion duration of the black phosphate coating in a copper sulfate spot test can be as long as 20 min.

  7. Application of Hyphenated Techniques in Speciation Analysis of Arsenic, Antimony, and Thallium

    Directory of Open Access Journals (Sweden)

    Rajmund Michalski

    2012-01-01

    Full Text Available Due to the fact that metals and metalloids have a strong impact on the environment, the methods of their determination and speciation have received special attention in recent years. Arsenic, antimony, and thallium are important examples of such toxic elements. Their speciation is especially important in the environmental and biomedical fields because of their toxicity, bioavailability, and reactivity. Recently, speciation analytics has been playing a unique role in the studies of biogeochemical cycles of chemical compounds, determination of toxicity and ecotoxicity of selected elements, quality control of food products, control of medicines and pharmaceutical products, technological process control, research on the impact of technological installation on the environment, examination of occupational exposure, and clinical analysis. Conventional methods are usually labor intensive, time consuming, and susceptible to interferences. The hyphenated techniques, in which separation method is coupled with multidimensional detectors, have become useful alternatives. The main advantages of those techniques consist in extremely low detection and quantification limits, insignificant interference, influence as well as high precision and repeatability of the determinations. In view of their importance, the present work overviews and discusses different hyphenated techniques used for arsenic, antimony, and thallium species analysis, in different clinical, environmental and food matrices.

  8. Determination of Trace Antimony (III by Adsorption Voltammetry at Carbon Paste Electrode

    Directory of Open Access Journals (Sweden)

    Nongyue He

    2005-05-01

    Full Text Available This work presents a sensitive method for the determination of trace antimonybased on the antimony-pyrogallol red (PGR adsorption at a carbon paste electrode (CPE.The optimal conditions were to use an electrode containing 25% paraffin oil and 75%high purity graphite powder as working electrode, a 0.10 mol/L HCl solution containing3.0×10-5 mol/L PGR as accumulation medium and a 0.20 mol/L HCl solution aselectrolyte with an accumulation time of 150 s and a reduction time of 60 s at -0.50 Vfollowed with a sweep from -0.50 V to 0.20 V. The mechanism of the electrode reactionwas discussed. Interferences of other metal ions were studied as well. The detection limitwas 1×10-9 mol/L. The linear range was from 2.0×10-9 mol/L to 5.0×10-7 mol/L.Application of the proposed method to the determination of antimony in water andhuman hair samples gave good results.

  9. Morphology-controlled growth of crystalline antimony sulfide via a refluxing polyol process

    Science.gov (United States)

    Zhang, Rui; Chen, Xiangying; Mo, Maosong; Wang, Zhenghua; Zhang, Meng; Liu, Xinyuan; Qian, Yitai

    2004-02-01

    By refluxing antimony trichloride (SbCl 3) and thiourea in various solvents at suitable reaction conditions, antimony sulfide (Sb 2S 3) crystallites with a diversity of well-defined morphologies were synthesized. Sb 2S 3 rods with the average diameter of 800 nm and the length of 7 μm, as well as microtubes with the average outer diameter of 1.2 μm, the average inner diameter of 800 nm and the length of 8 μm, were obtained in 1,2-propanediol at 180°C for 10 min. In contrast, a series of experiments under different conditions were carried out to investigate the influencing factors on the reaction. The as-synthesized products were characterized by powder X-ray diffraction, field-emission scanning electron microscopy, transmission electron microscope and X-ray photoelectron spectra. The results indicate Sb 2S 3 crystals with different morphologies, including rod-like, tube-like, bowknot-like, flower-like, straw-bundled-like, taken under different experimental conditions. It is found that the reaction temperature, time, solvent and poly(vinyl pyrrolidone) (as a polymer capping reagent) play important roles in the formation of the final Sb 2S 3 crystallites with different morphologies. Also, the possible growth mechanism is discussed.

  10. Effect of antimony incorporation on structural properties of CuInS{sub 2} crystals

    Energy Technology Data Exchange (ETDEWEB)

    Ben Rabeh, M., E-mail: mohamedbenrabeh@yahoo.f [Laboratoire de Photovoltaique et Materiaux Semi-Conducteurs - ENIT BP 37, Le belvedere, 1002 Tunis (Tunisia); Chaglabou, N., E-mail: nadia_chaglabou@yahoo.f [Laboratoire de Photovoltaique et Materiaux Semi-Conducteurs - ENIT BP 37, Le belvedere, 1002 Tunis (Tunisia); Kanzari, M., E-mail: Mounir.Kanzari@ipeit.rnu.t [Laboratoire de Photovoltaique et Materiaux Semi-Conducteurs - ENIT BP 37, Le belvedere, 1002 Tunis (Tunisia)

    2010-02-15

    CuInS{sub 2} (CIS) single crystals doped with 1, 2, 3 and 4 atomic percent (at.%) of antimony (Sb) were grown by the horizontal Bridgman method. The effect of Sb doping on the structural properties of CIS crystal was studied by means of X-ray diffraction (XRD), energy dispersive X-ray analysis (EDAX), scanning electron microscopy (SEM) and PL measurements. X-ray diffraction data suggests that the doping of Sb in the CIS single crystals does not affect the tetragonal (chalcopyrite) crystal structure and exhibited a (1 1 2) preferred orientation. In addition, with increasing Sb concentration, the X-ray diffraction analysis show that Sb doped CIS crystals are more crystallized and the diffraction peaks of the CuInS{sub 2} phase were more pronounced in particular the (1 1 2) plane. EDAX study revealed that Sb atoms can occupy the indium site and/or occupying the sulfur site to make an acceptor. PL spectra of undoped and Sb doped CIS crystals show two emission peaks at 1.52 and 1.62 eV, respectively which decreased with increasing atomic percent antimony. Sb doped CIS crystals show p-type conductivity.

  11. Food crop accumulation and bioavailability assessment for antimony (Sb) compared with arsenic (As) in contaminated soils.

    Science.gov (United States)

    Wilson, Susan C; Tighe, Matthew; Paterson, Ewan; Ashley, Paul M

    2014-10-01

    Field samples and a 9-week glasshouse growth trial were used to investigate the accumulation of mining derived arsenic (As) and antimony (Sb) in vegetable crops growing on the Macleay River Floodplain in Northern New South Wales, Australia. The soils were also extracted using EDTA to assess the potential for this extractant to be used as a predictor of As and Sb uptake in vegetables, and a simplified bioaccessibility extraction test (SBET) to understand potential for uptake in the human gut with soil ingestion. Metalloids were not detected in any field vegetables sampled. Antimony was not detected in the growth trial vegetable crops over the 9-week greenhouse trial. Arsenic accumulation in edible vegetable parts was risk of exposure through short-term vegetable crops is low. The data also demonstrate that uptake pathways for Sb and As in the vegetables were different with uptake strongly impacted by soil properties. A fraction of soil-borne metalloid was soluble in the different soils resulting in Sb soil solution concentration (10.75 ± 0.52 μg L(-1)) that could present concern for contamination of water resources. EDTA proved a poor predictor of As and Sb phytoavailability. Oral bioaccessibility, as measured by SBET, was risk from soil borne As and Sb in the floodplain environment.

  12. Determination of antimony in nail and hair by thermal neutron activation analysis

    International Nuclear Information System (INIS)

    The concentration of antimony in nail and hair was determined by thermal neutron activation analysis. Samples were collected from the workers of an antimony refinery, inhabitants near the refinery, and residents in control area. They were irradiated by Kyoto University 5000 kW Reactor for 1 h, and cooled for 30 to 100 days. After cooling, the concentration of Sb in nail and hair was estimated by measuring the intensity of γ-ray from 124Sb of the samples, then the samples were washed by 0.1 % aqueous solution of nonionic surface active agent in an ultrasonic cleaner. The γ-ray spectrometry was done again (after washing). The concentration of Sb in nail before washing was 730 ppm for the workers, 2.46 ppm for habitants near the refinery, and 0.19 ppm for the control; after washing, it became 230 ppm for the workers, 0.63 ppm for habitants, and 0.09 ppm for the control. The concentration of Sb in hair before and after washing was 222 ppm and 196 ppm for the workers, and 0.21 ppm and 0.15 ppm for the control, respectively. (author)

  13. One-step synthesis of antimony-doped tin dioxide nanocrystallites and their property

    Institute of Scientific and Technical Information of China (English)

    ZHENG Min; WANG Bao

    2009-01-01

    Antimony-doped tin dioxide(ATO) nanoparticles with primary diameter in the range of 9-10 nm were rapidly synthesized via a novel combustion technique, starting with antimony trichloride and tin tetrachloride as metal sources and self-assembly compounds as fuels. The combustion phenomena and characteristics of products were controlled by assembling components in fuel compounds according to appropriate molar ratio. The as-synthesized products were characterized by XRD, SEM, TEM and XPS, respectively. The electrical conductivity was evaluated through measuring the antistatic property of polyester fiber treated by the as-synthesized products. The results show that a mild combustion phenomena without release of smoke can be taken on and perfect azury rutile ATO crystal with complete substitution can be formed rapidly under the appropriate synthetic conditions. The antistatic property of the polyester fiber treated by the as-synthesized ATO products is enhanced remarkably. The triboelectricity voltage below 1.0 kV, half life below 1.0 s and surface resistance below 1.0×106 Ω can be attained.

  14. Growth of antimony doped P-type zinc oxide nanowires for optoelectronics

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Zhong Lin; Pradel, Ken

    2016-09-27

    In a method of growing p-type nanowires, a nanowire growth solution of zinc nitrate (Zn(NO.sub.3).sub.2), hexamethylenetetramine (HMTA) and polyethylenemine (800 M.sub.w PEI) is prepared. A dopant solution to the growth solution, the dopant solution including an equal molar ration of sodium hydroxide (NaOH), glycolic acid (C.sub.2H.sub.4O.sub.3) and antimony acetate (Sb(CH.sub.3COO).sub.3) in water is prepared. The dopant solution and the growth solution combine to generate a resulting solution that includes antimony to zinc in a ratio of between 0.2% molar to 2.0% molar, the resulting solution having a top surface. An ammonia solution is added to the resulting solution. A ZnO seed layer is applied to a substrate and the substrate is placed into the top surface of the resulting solution with the ZnO seed layer facing downwardly for a predetermined time until Sb-doped ZnO nanowires having a length of at least 5 .mu.m have grown from the ZnO seed layer.

  15. Effect of Annealing on the Properties of Antimony Telluride Thin Films and Their Applications in CdTe Solar Cells

    Directory of Open Access Journals (Sweden)

    Zhouling Wang

    2014-01-01

    Full Text Available Antimony telluride alloy thin films were deposited at room temperature by using the vacuum coevaporation method. The films were annealed at different temperatures in N2 ambient, and then the compositional, structural, and electrical properties of antimony telluride thin films were characterized by X-ray fluorescence, X-ray diffraction, differential thermal analysis, and Hall measurements. The results indicate that single phase antimony telluride existed when the annealing temperature was higher than 488 K. All thin films exhibited p-type conductivity with high carrier concentrations. Cell performance was greatly improved when the antimony telluride thin films were used as the back contact layer for CdTe thin film solar cells. The dark current voltage and capacitance voltage measurements were performed to investigate the formation of the back contacts for the cells with or without Sb2Te3 buffer layers. CdTe solar cells with the buffer layers can reduce the series resistance and eliminate the reverse junction between CdTe and metal electrodes.

  16. Progress of Antimony-containing Wastewater Treatment%含锑废水处理技术研究进展

    Institute of Scientific and Technical Information of China (English)

    尹鑫; 周广柱; 王翠珍; 王世豪; 彭刚; 何双

    2014-01-01

    在锑矿的开采及冶炼加工过程中,排出了大量含锑废水,这种重金属废水对环境和人体健康构成严重威胁。本文总结了重金属锑元素的物理化学性质、毒性特点,归纳了含锑废水的处理方法,分析了含锑废水处理技术的优势和缺点,提出了工艺联合应用等高效处理含锑废水的相关建议。%A large amount of wastewater containing antimony discharged in the process of antimony ore mining,smelting and processing,which pose a serious threat to the environment and human health. In this paper we summarized the characteristics of physical and chemical properties, toxicity of antimony, and the antimony wastewater treatment. Advantages and disadvantages of these treatment crafts were compared in a table,the recommendations given out for more efficiently processing via crafts combination.

  17. Electrochemical, structural and surface characterization of nickel/zirconia solid oxide fuel cell anodes in coal gas containing antimony

    Science.gov (United States)

    Marina, Olga A.; Pederson, Larry R.; Coyle, Christopher A.; Thomsen, Edwin C.; Nachimuthu, Ponnusamy; Edwards, Danny J.

    The interactions of antimony with the nickel-zirconia anode in solid oxide fuel cells (SOFCs) have been investigated. Tests with both anode-supported and electrolyte-supported button cells were performed at 700 and 800 °C in synthetic coal gas containing 100 ppb to 9 ppm antimony. Minor performance loss was observed immediately after Sb introduction to coal gas resulting in ca. 5% power output drop. While no further degradation was observed during the following several hundred hours of testing, cells abruptly and irreversibly failed after 800-1600 h depending on Sb concentration and test temperature. Antimony was found to interact strongly with nickel resulting in extensive alteration phase formation, consistent with expectations based on thermodynamic properties. Nickel antimonide phases, NiSb and Ni 5Sb 2, were partially coalesced into large grains and eventually affected electronic percolation through the anode support. Initial degradation was attributed to diffusion of antimony to the active anode/electrolyte interface to form an adsorption layer, while the late stage degradation was due the Ni-Sb phase formation. Assuming an average Sb concentration in coal gas of 0.07 ppmv, a 500 μm thick Ni/zirconia anode-supported cell is not expected to fail within 7 years when operated at a power output of 0.5 W cm -2 and fuel utilization above 50%.

  18. Ambulatory oesophageal pH monitoring : a comparison between antimony, ISFET, and glass pH electrodes

    NARCIS (Netherlands)

    Hemmink, Gerrit J. M.; Weusten, Bas L. A. M.; Oors, Jac; Bredenoord, Albert J.; Timmer, Robin; Smout, Andre J. P. M.

    2010-01-01

    Background and aim Ambulatory oesophageal pH-impedance monitoring is a widely used test to evaluate patients with reflux symptoms. Several types of pH electrodes are available: antimony, ion sensitive field effect transistor (ISFET), and glass electrodes. These pH electrodes have not been compared d

  19. POLICY China’s Ministry of Commerce Set the Rules for Antimony and Tungsten Export in 2005

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    <正> China’s ministry of commerce recently re-leased the rules and application procedures forthe export of antimony and tungsten productsin 2005 by the domestic producers.Based on the rules set by the ministry,China’santimony and tungsten producers providingtheir products for export must be those enter-prises authorized by the related State authori-ties.

  20. Comparative phytotoxicity of methylated and inorganic arsenic- and antimony species to Lemna minor, Wolffia arrhiza and Selenastrum capricornutum

    NARCIS (Netherlands)

    L. Duester; H.G. van der Geest; S. Moelleken; A.V. Hirner; K. Kueppers

    2011-01-01

    The alkylation of metalloids through the transfer of methyl groups is an important factor in the biogeochemical cycling of elements like arsenic and antimony. In the environment, many different organic and inorganic forms of these elements can therefore be found in soils, sediments or organisms. Stu

  1. On-line cloud point extraction combined with electrothermal vaporization inductively coupled plasma atomic emission spectrometry for the speciation of inorganic antimony in environmental and biological samples

    Energy Technology Data Exchange (ETDEWEB)

    Li Yingjie [Department of Chemistry, Wuhan University, Wuhan 430072 (China); Hu Bin [Department of Chemistry, Wuhan University, Wuhan 430072 (China)]. E-mail: binhu@whu.edu.cn; Jiang Zucheng [Department of Chemistry, Wuhan University, Wuhan 430072 (China)

    2006-08-25

    A new method for the determination of inorganic Sb species by on-line cloud point extraction combined with electrothermal vaporization inductively coupled plasma atomic emission spectrometry (ETV-ICP-AES) is presented and evaluated. The method is based on the complexation of Sb(III) with pyrrolidine dithiocarbamate (PDC) which form an hydrophobic complex at pH 5.5 and subsequently enter surfactant-rich phase at pH 5.5, whereas Sb(V) remained in aqueous solutions. The preconcentration step is mediated by micelles of the non-ionic surfactant Triton X-114 with ammonium pyrrolidine dithiocarbamate (APDC). The micellar system containing the complex was loaded into the FIA manifold at a flow rate of 2.5 mL min{sup -1}, and the surfactant-rich phase was retained in a microcolumn packed with absorbent cotton, at pH 5.5. After the surfactant-rich phase was eluted with 100 {mu}L acetonitrile, it was determined by ETV-ICP-AES. Sb(V) is reduced to Sb(III) by L-cysteine prior to determined total Sb, and its assay is based on subtracting Sb(III) from total antimony. The main factors affecting separation/preconcentration and the vaporization behavior of analyte in graphite tube were investigated in detail. Under the optimized conditions, the precision relative standard deviation (R.S.D.) for eight replicate measurements of 0.2 {mu}g mL{sup -1} Sb(III) was 4.3%. The apparent concentration factor, which is defined as the concentration ratio of the analyte in the final diluted surfactant-rich extract ready for ETV-ICP-AES detection and in the initial solution, was 872 for Sb(III). The limit of detection (LOD) for Sb(III) was 0.09 {mu}g L{sup -1}. The proposed method was successfully applied for the speciation of inorganic antimony in different water samples and urine sample with satisfactory results.

  2. American cutaneous leishmaniasis caused by Leishmania (Viannia) braziliensis resistant to meglumine antimoniate, but with good response to pentamidine: a case report.

    Science.gov (United States)

    Pimentel, Maria Inês Fernandes; Baptista, Cibele; Rubin, Evelyn Figueiredo; Vasconcellos, Erica de Camargo Ferreira e; Lyra, Marcelo Rosandiski; Salgueiro, Mariza de Matos; Saheki, Maurício Naoto; Rosalino, Cláudia Maria Valete; Madeira, Maria de Fátima; Silva, Aline Fagundes da; Confort, Eliame Mouta; Schubach, Armando de Oliveira

    2011-01-01

    This is a case report of a Brazilian soldier with cutaneous leishmaniasis. The lesion relapsed following two systemic treatments with meglumine antimoniate. The patient was treated with amphotericin B, which was interrupted due to poor tolerance. Following isolation of Leishmania sp., six intralesional infiltrations of meglumine antimoniate resulted in no response. Leishmania sp promastigotes were again isolated. The patient was submitted to intramuscular 4 mg/kg pentamidine. Parasites from the first and second biopsies were identified as Leishmania (Viannia) braziliensis; those isolated from the first biopsy were more sensitive to meglumine antimoniate in vitro than those isolated from the second biopsy. No relapse was observed. PMID:21552747

  3. American cutaneous leishmaniasis caused by Leishmania (Viannia) braziliensis resistant to meglumine antimoniate, but with good response to pentamidine: a case report.

    Science.gov (United States)

    Pimentel, Maria Inês Fernandes; Baptista, Cibele; Rubin, Evelyn Figueiredo; Vasconcellos, Erica de Camargo Ferreira e; Lyra, Marcelo Rosandiski; Salgueiro, Mariza de Matos; Saheki, Maurício Naoto; Rosalino, Cláudia Maria Valete; Madeira, Maria de Fátima; Silva, Aline Fagundes da; Confort, Eliame Mouta; Schubach, Armando de Oliveira

    2011-01-01

    This is a case report of a Brazilian soldier with cutaneous leishmaniasis. The lesion relapsed following two systemic treatments with meglumine antimoniate. The patient was treated with amphotericin B, which was interrupted due to poor tolerance. Following isolation of Leishmania sp., six intralesional infiltrations of meglumine antimoniate resulted in no response. Leishmania sp promastigotes were again isolated. The patient was submitted to intramuscular 4 mg/kg pentamidine. Parasites from the first and second biopsies were identified as Leishmania (Viannia) braziliensis; those isolated from the first biopsy were more sensitive to meglumine antimoniate in vitro than those isolated from the second biopsy. No relapse was observed.

  4. Determination of natural isotopic variation in antimony using inductively coupled plasma mass spectrometry for an uncertainty estimation of the standard atomic weight of antimony

    International Nuclear Information System (INIS)

    The isotopic variation of industrially produced antimony was estimated using multiple-collector inductively coupled plasma mass spectrometry. A reproducible 123Sb/121Sb ratio of ±0.004% (2 standard deviations) was routinely obtained using a Sn doping mass discrimination correction technique. Only a small isotopic variation of about 0.05% was observed among industrially important Sb materials (five commercially available reagents and two ore minerals). The degree of Sb isotopic variation to determine the uncertainty in Sb atomic weight can be reduced by this new analytical technique to 0.00025 compared to the currently accepted IUPAC isotopic variation determined by conventional mass spectrometry of ±0.001. Heavy isotope enrichment of Sb in a drainage water sample from a stibnite mining area was found. This heavy isotope enrichment tendency in an aqueous environment may be useful in detecting anthropogenic Sb input from industrial emission by the smelting process via air because Sb of anthropogenic origin will have lighter isotope enrichment features. (author)

  5. Adsorption of antimony(V) onto Mn(II)-enriched surfaces of manganese-oxide and FeMn binary oxide.

    Science.gov (United States)

    Liu, Ruiping; Xu, Wei; He, Zan; Lan, Huachun; Liu, Huijuan; Qu, Jiuhui; Prasai, Tista

    2015-11-01

    Manganese(IV) oxide [Mn(IV)] potentially oxidizes antimony(III) [Sb(III)] to antimony(V) [Sb(V)] and improves Sb removal by FeMn binary oxide (FMBO) through an oxidation-adsorption mechanism. This study focused on the effect of Mn(IV) reductive dissolution by potassium sulfite (K2SO3) on Sb(V) adsorption onto manganese oxide (Mn-oxide) and FMBO. The maximum Sb(V) adsorption (Qmax,Sb(V)) increased from 1.0 to 1.1 mmol g(-1) for FMBO and from 0.4 to 0.6 mmol g(-1) for Mn-oxide after pretreatment with 10 mmol L(-1) K2SO3. The addition of 2.5 mmol L(-1) Mn(2+) also significantly improved Sb(V) adsorption, and the observed Qmax,Sb(V) increased to 1.4 and 1.0 mmol g(-1) for FMBO and Mn-oxide, respectively, with pre-adsorbed Mn(2+). Neither K2SO3 nor Mn(2+) addition had any effect on Sb(V) adsorption onto iron oxide (Fe-oxide). Mn(2+) introduced by either Mn(IV) dissolution or addition tended to form outer-sphere surface complexes with hydroxyl groups on Mn-oxide surfaces (MnOOH). Mn(2+) at 2.5 mmol L(-1) shifted the isoelectric point (pHiep) from 7.5 to 10.2 for FMBO and from 4.8 to 9.2 for Mn-oxide and hence benefited Sb(V) adsorption. The adsorption of Sb(V) onto Mn(2+)-enriched surfaces contributed to the release of Mn(2+), and the X-ray photoelectron spectra also indicated increased binding energy of Mn 2p3/2 after the adsorption of Sb(V) onto K2SO3-pretreated FMBO and Mn-oxide. Sb(V) adsorption involved the formation of inner-sphere complexes and contributed to the release of Mn(2+). In the removal of Sb(III) by Mn-based oxides, the oxidation of Sb(III) to Sb(V) by Mn(IV) oxides had an effect; however, Mn(IV) dissolution and Mn(2+)-enrichment also played an important role.

  6. First-Principles Study of Antimony Doping Effects on the Iron-Based Superconductor CaFe(SbxAs1-x)2

    Science.gov (United States)

    Nagai, Yuki; Nakamura, Hiroki; Machida, Masahiko; Kuroki, Kazuhiko

    2015-09-01

    We study antimony doping effects on the iron-based superconductor CaFe(SbxAs1-x)2 by using the first-principles calculation. The calculations reveal that the substitution of a doped antimony atom into As of the chainlike As layers is more stable than that into FeAs layers. This prediction can be checked by experiments. Our results suggest that doping homologous elements into the chainlike As layers, which only exist in the novel 112 system, is responsible for rising up the critical temperature. We discuss antimony doping effects on the electronic structure. It is found that the calculated band structures with and without the antimony doping are similar to each other within our framework.

  7. Phytoavailability of antimony and heavy metals in arid regions: the case of the Wadley Sb district (San Luis, Potosí, Mexico).

    Science.gov (United States)

    Levresse, G; Lopez, G; Tritlla, J; López, E Cardellach; Chavez, A Carrillo; Salvador, E Mascuñano; Soler, A; Corbella, M; Sandoval, L G Hernández; Corona-Esquivel, R

    2012-06-15

    This paper presents original results on the Sb and heavy metals contents in sediments and waste tailings, plants and water from the giant Wadley antimony mine district (San Luis Potosí State, Mexico). The dominant antimony phases in mining wastes are stibiconite, montroydite and minor hermimorphite. The waste tailings contain high concentrations of metals and metalloids (antimony, iron, zinc, arsenic, copper, and mercury). Manganese, copper, zinc, and antimony contents exceed the quality guidelines values for groundwater, plants and for waste tailings. Results indicate that peak accumulation is seasonal due to the concentration by high metabolism plants as Solanaceae Nicotiana. The metal phytoavailability in waste tailings is highly dependant on the metal speciation, its capability to be transported in water and, more particularly, the plant metabolism efficiency.

  8. Thermoelectric transport in surface- and antimony-doped bismuth telluride nanoplates

    Science.gov (United States)

    Pettes, Michael Thompson; Kim, Jaehyun; Wu, Wei; Bustillo, Karen C.; Shi, Li

    2016-10-01

    We report the in-plane thermoelectric properties of suspended (Bi1-xSbx)2Te3 nanoplates with x ranging from 0.07 to 0.95 and thicknesses ranging from 9 to 42 nm. The results presented here reveal a trend of increasing p-type behavior with increasing antimony concentration, and a maximum Seebeck coefficient and thermoelectric figure of merit at x ˜ 0.5. We additionally tuned extrinsic doping of the surface using a tetrafluoro-tetracyanoquinodimethane (F4-TCNQ) coating. The lattice thermal conductivity is found to be below that for undoped ultrathin Bi2Te3 nanoplates of comparable thickness and in the range of 0.2-0.7 W m-1 K-1 at room temperature.

  9. A novel composite material based on antimony(III) oxide and amorphous silica

    Energy Technology Data Exchange (ETDEWEB)

    Zemnukhova, Ludmila A. [Institute of Chemistry, Far-Eastern Branch, Russian Academy of Sciences, 690022 Vladivostok (Russian Federation); Panasenko, Alexander E., E-mail: panasenko@ich.dvo.ru [Institute of Chemistry, Far-Eastern Branch, Russian Academy of Sciences, 690022 Vladivostok (Russian Federation)

    2013-05-01

    The composite material nSb₂O₃·mSiO₂·xH₂O was prepared by hydrolysis of SbCl₃ and Na₂SiO₃ in an aqueous medium. It has been shown that the composition of the material is influenced by the ratio of the initial components and the acidity of the reaction medium. The morphology of the material particles and its specific surface area have been determined. The thermal and optic properties were also investigated. - Graphical abstract: Novel composite material containing amorphous silica and crystal antimony(III) oxide has been synthesized by hydrolysis of SbCl₃ and Na₂SiO₃ in an aqueous medium. Highlights: • The composite material nSb₂O₃·mSiO₂·xH₂O was prepared in an aqueous medium. • The composition of the material is controllable by a synthesis conditions. • The morphology of the material and its optic properties have been determined.

  10. Preparation and characterization of conductive antimony-doped tin oxide (ATO) nanoparticles

    Institute of Scientific and Technical Information of China (English)

    LIN; Feng; DUAN; Xue-chen; REN; Xian-jing

    2005-01-01

    In this paper, conductive antimony-doped tin oxide (ATO) composite particles is prepared by hydroxylation method of metal alcoxides. This method has many advantages such as little pollution, low cost, simple sheet and equipment. The synthesis processing and the ATO nanoparticles are characterized by means of transmission electron microscope (TEM), X-ray diffraction (XRD), thermal gravimetric and differential thermal analysis, and BET. The results show that the ATO nanoparticles is tetragonal rutile crystal structure. TEM show that the particles are monodispersed with weak aggromation. The size of the particles calcinated at 700 is about 8nm. The specific areas are 153 m2 · g-1. In addition to, ATO nanop articles have good electric properties

  11. Sequential solvent extraction for forms of antimony in five selected coals

    Science.gov (United States)

    Qi, C.; Liu, Gaisheng; Kong, Y.; Chou, C.-L.; Wang, R.

    2008-01-01

    Abundance of antimony in bulk samples has been determined in five selected coals, three coals from Huaibei Coalfield, Anhui, China, and two from the Illinois Basin in the United States. The Sb abundance in these samples is in the range of 0.11-0.43 ??g/g. The forms of Sb in coals were studied by sequential solvent extraction. The six forms of Sb are water soluble, ion changeable, organic matter bound, carbonate bound, silicate bound, and sulfide bound. Results of sequential extraction show that silicate-bound Sb is the most abundant form in these coals. Silicate- plus sulfide-bound Sb accounts for more than half of the total Sb in all coals. Bituminous coals are higher in organic matterbound Sb than anthracite and natural coke, indicating that the Sb in the organic matter may be incorporated into silicate and sulfide minerals during metamorphism. ?? 2008 by The University of Chicago. All rights reserved.

  12. Reduced Graphene Oxide/Tin-Antimony Nanocomposites as Anode Materials for Advanced Sodium-Ion Batteries.

    Science.gov (United States)

    Ji, Liwen; Zhou, Weidong; Chabot, Victor; Yu, Aiping; Xiao, Xingcheng

    2015-11-11

    Reduced graphene oxides loaded with tin-antimony alloy (RGO-SnSb) nanocomposites were synthesized through a hydrothermal reaction and the subsequent thermal reduction treatments. Transmission electron microscope images confirm that SnSb nanoparticles with an average size of about 20-30 nm are uniformly dispersed on the RGO surfaces. When they were used as anodes for rechargeable sodium (Na)-ion batteries, these as-synthesized RGO-SnSb nanocomposite anodes delivered a high initial reversible capacity of 407 mAh g(-1), stable cyclic retention for more than 80 cycles and excellent cycle stability at ultra high charge/discharge rates up to 30C. The significantly improved performance of the synthesized RGO-SnSb nanocomposites as Na-ion battery anodes can be attributed to the synergetic effects of RGO-based flexible framework and the nanoscale dimension of the SnSb alloy particles (batteries.

  13. Novel antimony doped tin oxide/carbon aerogel as efficient electrocatalytic filtration membrane

    Directory of Open Access Journals (Sweden)

    Zhimeng Liu

    2016-05-01

    Full Text Available A facile method was developed to prepare antimony doped tin oxide (Sb-SnO2/carbon aerogel (CA for use as an electrocatalytic filtration membrane. The preparation process included synthesis of a precursor sol, impregnation, and thermal decomposition. The Sb-SnO2, which was tetragonal in phase with an average crystallite size of 10.8 nm, was uniformly distributed on the CA surface and firmly attached via carbon-oxygen-tin chemical bonds. Preliminary filtration tests indicated that the Sb-SnO2/CA membrane had a high rate of total organic carbon removal for aqueous tetracycline owing to its high current efficiency and electrode stability.

  14. Novel fabrication of an electrochromic antimony-doped tin oxide film using a nanoparticle deposition system

    Science.gov (United States)

    Kim, Hyungsub; Park, Yunchan; Choi, Dahyun; Ahn, Sung-Hoon; Lee, Caroline Sunyong

    2016-07-01

    Novel deposition method of Antimony-doped tin oxide (ATO) thin films was introduced using a nanoparticle deposition system (NPDS) to fabricate an electrochromic (EC) device. NPDS is a dry deposition method that simplifies the ATO deposition process by eliminating the need for solvents or binders. In this study, an ATO EC layer was deposited using NPDS. The surface morphology and electrochemical and optical transmittance properties were characterized. The optical transmittance change in the ATO EC device was ∼35% over the wavelength range of 350-800 nm, and the cyclic transmittance was stable. The ATO film deposited using NPDS, exhibited a coloration efficiency of 15.5 cm2 C-1. Therefore, our results suggest that ATO EC devices can be fabricated using a simple, cost-effective NPDS, which allows nanoparticles to be deposited directly without pre- or post-processing.

  15. Microbial diversity and community structure in an antimony-rich tailings dump.

    Science.gov (United States)

    Xiao, Enzong; Krumins, Valdis; Dong, Yiran; Xiao, Tangfu; Ning, Zengping; Xiao, Qingxiang; Sun, Weimin

    2016-09-01

    To assess the impact of antimony (Sb) on microbial community structure, 12 samples were taken from an Sb tailings pile in Guizhou Province, Southwest China. All 12 samples exhibited elevated Sb concentrations, but the mobile and bioaccessible fractions were small in comparison to total Sb concentrations. Besides the geochemical analyses, microbial communities inhabiting the tailing samples were characterized to investigate the interplay between the microorganisms and environmental factors in mine tailings. In all samples, Proteobacteria and Actinobacteria were the most dominant phyla. At the genus level, Thiobacillus, Limnobacter, Nocardioides, Lysobacter, Phormidium, and Kaistobacter demonstrated relatively high abundances. The two most abundant genera, Thiobacillus and Limnobacter, are characterized as sulfur-oxidizing bacteria and thiosulfate-oxidizing bacteria, respectively, while the genus Lysobacter contains arsenic (As)-resistant bacteria. Canonical correspondence analysis (CCA) indicates that TOC and the sulfate to sulfide ratio strongly shaped the microbial communities, suggesting the influence of the environmental factors in the indigenous microbial communities. PMID:27188777

  16. Properties of antimony doped ZnO thin films deposited by spray pyrolysis technique

    Energy Technology Data Exchange (ETDEWEB)

    Sadananda Kumar, N., E-mail: sadanthara@gmail.com; Bangera, Kasturi V.; Shivakumar, G. K. [National Institute of Technology Karnataka, Surathkal, Thin Films Laboratory, Department of Physics (India)

    2015-07-15

    Antimony (Sb) doped zinc oxide (ZnO) thin films were deposited on the glass substrate at 450°C using spray pyrolysis technique. Effect of Sb doping on surface morphology structural, optical and electrical properties were studied. X-ray diffraction (XRD) analysis showed that both the undoped and doped ZnO thin films are polycrystalline in nature with (101) preferred orientation. SEM analysis showed a change in surface morphology of Sb doped ZnO thin films. Doping results in a marked increase in conductivity without affecting the transmittance of the films. ZnO films prepared with 3 at % Sb shows the lowest resistivity of 0.185 Ohm cm with a Hall mobility of 54.05 cm{sup 2} V{sup –1} s{sup –1}, and a hole concentration of 6.25 × 10{sup 17} cm{sup –3}.

  17. Renal function evaluation in patients with American Cutaneous Leishmaniasis after specific treatment with pentavalent antimonial

    Directory of Open Access Journals (Sweden)

    Oliveira Rodrigo A

    2012-06-01

    Full Text Available Abstract Background Renal evaluation studies are rare in American Cutaneous Leishmaniasis (ACL. The aim of this study is to investigate whether specific treatment reverts ACL-associated renal dysfunction. Methods A prospective study was conducted with 37 patients with ACL. Urinary concentrating and acidification ability was assessed before and after treatment with pentavalent antimonial. Results The patients mean age was 35.6 ± 12 years and 19 were male. Before treatment, urinary concentrating defect (U/Posm Conclusion As previously described, urinary concentrating and acidification defects were found in an important number of patients with ACL. Present results demonstrate that only some patients recover urinary acidification capacity, while no one returned to normal urinary concentration capacity.

  18. 锑环境健康效应的研究进展%Environmental Health Effect of Antimony: a Review of Recent Researches

    Institute of Scientific and Technical Information of China (English)

    戈兆凤; 韦朝阳

    2011-01-01

    随着锑的开采及含锑产品的广泛应用,锑所带来的污染问题已越来越严重,锑对环境与健康的危害也受到了更多的关注.该文总结了锑环境健康效应的研究进展,从医学、环境毒理学和生态毒理学的角度分别分析了锑对人、动物以及植物与土壤生物的健康效应.提示今后还需加强锑的致癌性及基因毒性研究,并需从微观与宏观尺度揭示锑的毒性效应,以期为锑的环境健康风险评估提供科学依据.%The antimony mining and widely use of antimony products have resulted in serious antimony contamination,causing hazards to both the environment and human health. The present paper summarized the research progresses on the environmental health effect of antimony. The health effects of antimony on human, animals, and plants as well as soil organisms are introduced and discussed in the view of medical science, environmental toxicology and ecological toxicology, respectively. It is suggested that more researches should be conducted on antimony earcinogenieity and genotoxicity, and the toxic effects of antimony should be explored from micro and macroscopic scales in order to provide the scientific basis for risk assessment of antimony.

  19. Successful treatment of feline leishmaniosis using a combination of allopurinol and N-methyl-glucamine antimoniate

    Directory of Open Access Journals (Sweden)

    Maria Alexandra Basso

    2016-02-01

    Full Text Available Case summary This work describes the diagnosis and successful treatment of a 2-year-old domestic cat infected with Leishmania species and presenting fever, and ulcerative and nodular skin lesions after being treated for pyodermatitis for 1 year without clinical improvement. After anamnesis the cat was submitted to a complete clinical examination. Blood was collected for determination of haematological and biochemical parameters, detection of feline leukaemia virus (FeLV, feline immunodeficiency virus (FIV, feline coronavirus (FCoV and Leishmania amastigotes. Fine-needle aspiration puncture from the skin nodules was also performed. After definitive diagnosis the animal was treated and followed up over a 2 year period. The animal tested negative for FIV-specific antibodies, FeLV antigen and feline coronavirus RNA. Leishmania amastigotes in the skin nodules were confirmed by cytology and molecular diagnosis. Treatment was initiated with allopurinol, resulting in a slight clinical improvement. Thus, N-methyl-glucamine antimoniate was added and administered for 30 days, with complete closure of the ulcerative lesions in the hindlimbs requiring a surgical approach. Close monitoring of the patient in the following 24 months indicated that combined therapy was safe and clinical cure was achieved without further relapses or side effects. Relevance and novel information Considering the increasing number of feline leishmaniosis cases and the inconsistent results of most therapeutic protocols described in the literature, the use of new approaches, especially in refractory cases, is essential. Although the use of allopurinol and N-methyl-glucamine antimoniate is off-label in cats, in this case the combination treatment was followed by an extensive analytical monitoring, supporting their safety and effectiveness.

  20. Infrared-to-red upconversion luminescence in samarium-doped antimony glasses

    International Nuclear Information System (INIS)

    A new antimony-based glass system (K2O-B2O3-Sb2O3) having low phonon energy (about 600 cm-1) doped with Sm3+ ions has been developed. Infrared reflection spectroscopic (IRRS) studies have been employed to establish its low phonon energy. Ultraviolet-Visible-near infrared (UV-Vis-NIR) absorption and photoluminescence upconversion properties with the spectrochemistry of the 15K2O-15B2O3-70Sb2O3 (mol%) glasses have been studied doping with different concentrations (0.1-1.0 wt%) of Sm2O3. UV-Vis-NIR absorption band positions have been justified with quantitative calculation of nephelauxetic parameter and covalent bonding characteristics of the host. NIR to visible upconversion has been investigated by exciting at 949 nm at room temperature. Three upconverted bands originating from the 4G5/2→6H5/2, 4G5/2→6H7/2 and 4G5/2→6H9/2 transitions are found to be centered at 566 (green, weak), 602 (orange, weak) and 636 (red, remarkably strong) nm, respectively. These bands have been explained from the evaluation of the absorption, normal (downconversion) fluorescence and excitation spectra. The upconversion processes have been explained by the excited state absorption (ESA), energy transfer (ET) and cross-relaxation (CR) mechanisms involving population of the metastable (storage) energy level (4G5/2) by multiphonon deexcitation effect. It is evident from the IRRS study that the upconversion phenomena are expedited by the low multiphonon relaxation rate in antimony glasses owing to their low phonon energy (602 cm-1, the main and highest intensity Sb-O-Sb stretching band) which is very close to that of fluoride glasses (500-600 cm-1)

  1. Optical properties of Eu3+-doped antimony-oxide-based low phonon disordered matrices

    Science.gov (United States)

    Som, Tirtha; Karmakar, Basudeb

    2010-01-01

    A new series of monolithic Eu2O3-doped high antimony oxide (40-80 mol%) content disordered matrices (glasses) of low phonon energy (about 600 cm-1) in the K2O-B2O3-Sb2O3 (KBS) system was prepared by the melt-quench technique. Infrared reflection spectroscopy was used to establish the low phonon energy of the glasses. Amorphicity and devitrification of the glasses were confirmed by x-ray diffraction analysis. UV-vis absorption spectra of Eu3+ have been measured and the band positions have been justified with quantitative calculation of the nephelauxetic parameter and covalent bonding characteristics of the host. These Eu2O3-doped glasses upon excitation at 393 nm radiation exhibit six emission bands in the range 500-750 nm due to their low phonon energy. Of these, the magnetic dipole ^{5}\\mathrm {D}_{0} \\to {}^{7} \\mathrm {F_{1}} transition shows small Stark splitting while the electric dipole ^{5}\\mathrm {D}_{0} \\to {}^{7}\\mathrm {F}_{2} transition undergoes remarkable Stark splitting into two components. They have been explained by the crystal field effect. The Judd-Ofelt parameters, Ωt = 2,4,6, were also evaluated and the change of Ωt with the glass composition was correlated with the asymmetric effect at Eu3+ ion sites and the fundamental properties like covalent character and optical basicity. We are the first to report the spectroscopic properties of the Eu3+ ion in KBS low phonon antimony glasses.

  2. Optical characterization of antimony-based bismuth-doped thin films with different annealing temperatures

    Institute of Scientific and Technical Information of China (English)

    Xinmiao Lu; Yiqun Wu; Yang Wang; Jinsong Wei

    2011-01-01

    Antimony-b ased bismuth-doped thin film,a new kind of super-resolution mask layer,is prepared by magnetron sputtering.The structures and optical constants of the thin films before and after annealing are examined in detail.The as-deposited film is mainly in an amorphous state.After annealing at 170-370℃,it is converted to the rhombohedral-type of structure.The extent of crystallization increased with the annealing temperature.When the thin film is annealed,its refractive index decreased in the most visible region,whereas the extinction coefficient and reflectivity are markedly increased.The results indicate that the optical parameters of the film strongly depend on its microstructure and the bonding of the atoms.As demand for ultrahigh-density information storage continues to grow the recording mark size in optical memory is reduced to the nanometer scale [1- 4].Exceeding the optical diffraction limit with traditional optical storage technology has become a challenge[5-6].%Antimony-based bismuth-doped thin film, a new kind of super-resolution mask layer, is prepared by magnetron sputtering. The structures and optical constants of the thin films before and after annealing are examined in detail. The as-deposited film is mainly in an amorphous state. After annealing at 170-370℃, it is converted to the rhombohedral-type of structure. The extent of crystallization increased with the annealing temperature. When the thin film is annealed, its refractive index decreased in the most visible region, whereas the extinction coefficient and reflectivity are markedly increased. The results indicate that the optical parameters of the film strongly depend on its microstructure and the bonding of the atoms.

  3. Preparation and Structure Analysis of Antimony Trichloride and Bismuth Trichloride Comlexes with Valine%缬氨酸锑和缬氨酸铋配合物的制备与结构分析

    Institute of Scientific and Technical Information of China (English)

    杨宇翔; 郇伟伟; 纪国媛; 陈娅如

    2011-01-01

    Two compounds of antimony trichloride and bismuth trichloride with valine are synthesized by solid phase synthesis at room temperature.Their compositions,determined by element analysis, are Sb(C5H10O2N)3 · 2H2O and Bi(C5H10O2N)2Cl·0.5H2O.The crystal structure of antimony complex with valine belongs to triclinic system and its lattice parameters are: a = 0.959 9 nm, b = 1.506 8 nm,c=1.985 1 nm, α =92.27°,β= 95.05°,γ= 104.27°.The crystal structure of bismuth complex with valine belongs to monoclinic system and its lattice parameters are: a = 1.601 2 nm, b= 1.894 1 nm, c = 1.839 nm, β=99.73°.The farinfrared spectra and the infrared spectra show that the amino group and carboxyl of valine may be coordinated to antimony and bismuth, respectively, in two compounds.The TG-DSC results also reveal that the complexes are formed.%采用室温固相合成法合成了缬氨酸与三氯化锑、三氯化铋的两种生物配合物,其组成为Sb(C5H1002N)3·2H2O,Bi(C5 H1002N)2Cl·0.5H2O.缬氨酸锑配合物的晶体结构属于三斜晶系,晶胞参数为a=0.959 9 nm,b=1.506 8 nm,c=1.985 1 nm,α=92.27°,β=95.05°,γ=104.27°;缬氨酸铋配合物的晶体结构属于单斜晶系,晶胞参数为α=1.601 2nm,b=1.894 1 nm,c=1.839 nm,β=99.73°.远红外、红外光谱表明这两种新的配合物中锑、铋与缬氨酸的成键情况;并用差热-热重法对这两种配合物做了热分析,进一步验证了配合物的组成.

  4. Decreased antimony uptake and overexpression of genes of thiol metabolism are associated with drug resistance in a canine isolate of Leishmania infantum.

    Science.gov (United States)

    Gómez Pérez, Verónica; García-Hernandez, Raquel; Corpas-López, Victoriano; Tomás, Ana M; Martín-Sanchez, Joaquina; Castanys, Santiago; Gamarro, Francisco

    2016-08-01

    Visceral leishmaniasis (VL) caused by the protozoan parasite Leishmania infantum, is one of the most important zoonotic diseases affecting dogs and humans in the Mediterranean area. The presence of infected dogs as the main reservoir host of L. infantum is regarded as the most significant risk for potential human infection. We have studied the susceptibility profile to antimony and other anti-leishmania drugs (amphotericin B, miltefosine, paromomycin) in Leishmania infantum isolates extracted from a dog before and after two therapeutic interventions with meglumine antimoniate (subcutaneous Glucantime(®), 100 mg/kg/day for 28 days). After the therapeutic intervention, these parasites were significantly less susceptible to antimony than pretreatment isolate, presenting a resistance index of 6-fold to Sb(III) for promastigotes and >3-fold to Sb(III) and 3-fold to Sb(V) for intracellular amastigotes. The susceptibility profile of this resistant L. infantum line is related to a decreased antimony uptake due to lower aquaglyceroporin-1 expression levels. Additionally, other mechanisms including an increase in thiols and overexpression of enzymes involved in thiol metabolism, such as ornithine decarboxylase, trypanothione reductase, mitochondrial tryparedoxin and mitochondrial tryparedoxin peroxidase, could contribute to the resistance as antimony detoxification mechanisms. A major contribution of this study in a canine L. infantum isolate is to find an antimony-resistant mechanism similar to that previously described in other human clinical isolates. PMID:27317865

  5. Remediation of antimony-rich mine waters: Assessment of antimony removal and shifts in the microbial community of an onsite field-scale bioreactor.

    Science.gov (United States)

    Sun, Weimin; Xiao, Enzong; Kalin, Margarete; Krumins, Valdis; Dong, Yiran; Ning, Zengping; Liu, Tong; Sun, Min; Zhao, Yanlong; Wu, Shiliang; Mao, Jianzhong; Xiao, Tangfu

    2016-08-01

    An on-site field-scale bioreactor for passive treatment of antimony (Sb) contamination was installed downstream of an active Sb mine in Southwest China, and operated for one year (including a six month monitoring period). This bioreactor consisted of five treatment units, including one pre-aerobic cell, two aerobic cells, and two microaerobic cells. With the aerobic cells inoculated with indigenous mine water microflora, the bioreactor removed more than 90% of total soluble Sb and 80% of soluble antimonite (Sb(III)). An increase in pH and decrease of oxidation-reduction potential (Eh) was also observed along the flow direction. High-throughput sequencing of the small subunit ribosomal RNA (SSU rRNA) gene variable (V4) region revealed that taxonomically diverse microbial communities developed in the bioreactor. Metal (loid)-oxidizing bacteria including Ferrovum, Thiomonas, Gallionella, and Leptospirillum, were highly enriched in the bioreactor cells where the highest total Sb and Sb(III) removal occurred. Canonical correspondence analysis (CCA) indicated that a suite of in situ physicochemical parameters including pH and Eh were substantially correlated with the overall microbial communities. Based on an UPGMA (Unweighted Pair Group Method with Arithmetic Mean) tree and PCoA (Principal Coordinates Analysis), the microbial composition of each cell was distinct, indicating these in situ physicochemical parameters had an effect in shaping the indigenous microbial communities. Overall, this study was the first to employ a field-scale bioreactor to treat Sb-rich mine water onsite and, moreover, the findings suggest the feasibility of the bioreactor in removing elevated Sb from mine waters. PMID:27208755

  6. Antimony incorporation in InAs quantum dots grown on GaAs substrate by molecular beam epitaxy

    Science.gov (United States)

    Rihani, J.; Sallet, V.; Christophe, H. J.; Oueslati, M.; Chtourou, R.

    2008-01-01

    We have grown InAs(Sb) quantum dots (QDs) on GaAs (0 0 1) substrates by molecular beam epitaxy (MBE) using two different antimony exposures ( ΦSb). Atomic force microscopy (AFM) and photoluminescence (PL) spectroscopy were carried out to investigate the dot size evolution as function of the incorporated antimony content in InAs/GaAs QDs material. Anomalous asymmetric-band feature was observed in room temperature photoluminescence (RTPL) spectra of the investigated QD samples grown at relatively high temperature (490 °C). From the temperature-dependent PL measurements, it was found that the asymmetric-band feature is associated with the ground-states transitions from QDs with bimodal size distribution. The analysis of the pump power dependent PL spectra allows us to suggest a type II band lineup for the InAsSb/GaAs QDs materials system.

  7. Interest of lymphoscintigraphy with 99sup(m)Tc-labelled antimony sulfide in the arms after breast carcinoma treatment

    International Nuclear Information System (INIS)

    2 mCi of antimony sulfide colloid labelled with sup(99m)Tc were injected subcutaneously between the digits in 25 patients with postoperative lymphoedema of the arm for breast carcinoma. The two arms are examined successively, the normal one being used as control. The lymphoscintigraphy is realised with a gamma camera during an hour. The information obtained is threefoled; on the peripheral block's importance, the place where the lymphatic flow is stopped, and the presence in 40% of patients of axillary lymph nodes. The diminution of the lymphatic flow is not in correlation with the lymphoedema's importance. Lymphoscintigraphy with sup(99m)Tc antimony sulfide colloid is a simple examination but some side effects may occur. In 7 patients, post-injection lymphangitis was observed, with favorable evolution under antibiotic treatment. The lymphoscintigraphy can give some interesting information on the evolution of treated lymphoedema

  8. Speciation of very low amounts of arsenic and antimony in waters using dispersive liquid-liquid microextraction and electrothermal atomic absorption spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Rivas, Ricardo E.; Lopez-Garcia, Ignacio [Department of Analytical Chemistry, Faculty of Chemistry, University of Murcia, E-30071 Murcia (Spain); Hernandez-Cordoba, Manuel [Department of Analytical Chemistry, Faculty of Chemistry, University of Murcia, E-30071 Murcia (Spain)], E-mail: hcordoba@um.es

    2009-04-15

    A new procedure for the determination of inorganic arsenic (III,V) and antimony (III,V) in water samples by dispersive liquid-liquid micro extraction separation and electrothermal atomic absorption spectrometry (ETAAS) is presented. At pH 1, As(III) and Sb(III) are complexed with ammonium pyrrolidine dithiocarbamate and extracted into the fine droplets formed when mixing carbon tetrachloride (extraction solvent), methanol (disperser solvent) and the sample solution. After extraction, the phases are separated by centrifugation, and As(III) and Sb(III) are determined in the organic phase. As(V) and Sb(V) remain in the aqueous layer. Total inorganic As and Sb are determined after the reduction of the pentavalent forms with sodium thiosulphate. As(V) and Sb(V) are calculated by difference. The detection limits are 0.01 and 0.05 {mu}g L{sup -1} for As(III) and Sb(III), respectively, with an enrichment factor of 115. The relative standard deviation is in the 2.9-4.5% range. The procedure has been applied to the speciation of inorganic As and Sb in bottled, tap and sea water samples with satisfactory results.

  9. Co-administration of glycyrrhizic acid with the antileishmanial drug sodium antimony gluconate (SAG) cures SAG-resistant visceral leishmaniasis.

    Science.gov (United States)

    Bhattacharjee, Amrita; Majumder, Saikat; Majumdar, Suchandra Bhattacharyya; Choudhuri, Soumitra Kumar; Roy, Syamal; Majumdar, Subrata

    2015-03-01

    Since there are very few affordable antileishmanial drugs available, antimonial resistance has crippled antileishmanial therapy, thereby emphasising the need for development of novel therapeutic strategies. This study aimed to evaluate the antileishmanial role of combined therapy with sodium antimony gluconate (SAG) and the triterpenoid glycyrrhizic acid (GA) against infection with SAG-resistant Leishmania (GE1F8R). Combination therapy with GA and SAG successfully limited infection with SAG-resistant Leishmania in a synergistic manner (fractional inhibitory concentration index resistant Leishmania and co-treated with GA and SAG exhibited a significant reduction in hepatic and splenic parasite burden. In probing the mechanism, it was observed that GA treatment suppressed the expression and efflux activity of P-glycoprotein (P-gp) and multidrug resistance-associated protein 1 (MRP1), two host ABC transporters responsible for antimony efflux from host cells infected with SAG-resistant parasites. This suppression correlated with greater intracellular antimony retention during SAG therapy both in vitro and in vivo, which was reflected in the reduced parasite load. Furthermore, co-administration of GA and SAG induced a shift in the cytokine balance towards a Th1 phenotype by augmenting pro-inflammatory cytokines (such as IL-12, IFNγ and TNFα) and inducing nitric oxide generation in GE1F8R-infected macrophages as well as GE1F8R-infected mice. This study aims to provide an affordable leishmanicidal alternative to expensive antileishmanial drugs such as miltefosine and amphotericin B. Furthermore, this report explores the role of GA as a resistance modulator in MRP1- and P-gp-overexpressing conditions. PMID:25600891

  10. Exploring screen printing technology on thermoelectric energy harvesting with printing copper-nickel and bismuth-antimony thermocouples

    OpenAIRE

    Cao, Zhuo; Koukharenko, Elena; Torah, R; Beeby, SP

    2013-01-01

    This paper reports the fabrication and testing of copper (Cu) - nickel (Ni) and bismuth (Bi) - antimony (Sb) based thermocouples fabricated using screen printing technology. The transport properties of the printed thermoelectric material were measured in room temperature while the Seebeck voltage and power output of the printed thermocouples were tested under a variety temperature gradient. Initial thermoelectric materials have been integrated in inks and then deposited on substrate by the si...

  11. The Potential Impact of Biofield Energy Treatment on the Atomic and Physical Properties of Antimony Tin Oxide Nanopowder

    OpenAIRE

    Trivedi, Mahendra Kumar

    2015-01-01

    Antimony tin oxide (ATO) is known for its high thermal conductivity, optical transmittance, and wide energy band gap, which makes it a promising material for the display devices, solar cells, and chemical sensor industries. The present study was undertaken to evaluate the effect of biofield energy treatment on the atomic and physical properties of ATO nanopowder. The ATO nanopowder was divided into two parts: control and treated. The treated part was subjected to Mr. Trivedi’s biofield ...

  12. The influence of remelting on the properties of AlSi6Cu4 alloy modified by antimony

    OpenAIRE

    D. Medlen; D. Bolibruchova

    2012-01-01

    The paper deals with the problem of multiple remelting influence on AlSi6Cu4 alloy modified by antimony on chosen mechanical characteristics, microstructure and gas content. This foundry alloy is used mostly in automotive industry. Foundry Aluminum-Silicon alloys are also used in number of industrial weight sensitive applications because of their low weight and very good castability and good mechanical properties. Modifiers are usually added to molten aluminum-silicon alloys to refine the eut...

  13. EFFECT OF GRAIN BOUNDARY SEGREGATION OF ANTIMONY ON RELAXATION AT GRAIN BOUNDARIES IN SILICON-IRON ALLOYS

    OpenAIRE

    Iwasaki, Y.; Fujimoto, K

    1981-01-01

    A sharp grain boundary peak appears in both 2 and 3% silicon-iron alloys due to a substitutional solute of silicon. This peak is highly sensitive to the segregation of the third element of antimony and, contrary to orthodox solute peaks in binary and ternary alloys, largely decreases in magnitude on heating after a segregation treatment. The subsequent measurement on cooling returns the peak to the ordinary magnitude. As a function of annealing time at a temperature of segregation, the height...

  14. Evaluation of potential dietary toxicity of heavy metals in some common Nigerian beverages: A look at antimony, tin and mercury

    Directory of Open Access Journals (Sweden)

    I.I. Roberts

    2011-11-01

    Full Text Available There is currently little information on the composition of heavy metals in beverages imported and locally produced in Nigeria. The study quantitatively determined the composition of antimony (Sb, tin (Sn and mercury (Hg in 50 different beverage samples and evaluated the extent of violation of guideline values. Analysis of the beverage samples for the presence of Sb, Sn, and Hg was carried out using an atomic absorption spectrophotometer (AAS 929. The mean values detected for mercury, tin and antimony (±SE in fruit juices and soft drinks were 2.39±0.25, 3.66±0.22 and 0.49±0.048 μg/l; 2.93±0.34, 3.60±0.46 and 0.49±0.10 μg/l in dairy drinks and 0.94±0.02, 4.34±0.48 and 0.48±0.05 μg/l in bottled water samples respectively. While antimony detected in all products was below guideline values, mercury and tin were above the acceptable levels established by the World Health Organization, United States Environmental Protection Agency and European Union in most samples tested.

  15. Precipitation of antimony from the solution of sodium thioantimonite by air oxidation in the presence of catalytic agents

    Institute of Scientific and Technical Information of China (English)

    杨天足; 赖琼琳; 唐建军; 楚广

    2002-01-01

    The behavior of antimony oxidation in the solution of sodium thioantimonite was studied in the presence of catalytic agents. The catalytic effects of the respective addition of cupric sulfate, sodium tartrate, potassium permanganate, phenol, 1,2-dihydroxybenzene and their combination on the oxidation of sodium thioantimonite were investigated. A pilot test was carried out. The results show that the respective use of sodium tartrate, cupric sulfate, potassium permanganate, phenol and 1,2-dihydroxybenzene have little catalytic effect on the oxidation of sodium thioantimonite. However there exists obvious catalytic oxidation by the combination of 0.25 g/L 1,2-dihydroxybenzene, 0.5 g/L potassium permanganate and 1.0 g/L phenol. Moreover, high blast intensity, the increase of temperature and NaOH concentration favor the oxidation of antimony. The oxidation process of antimony has such advantages as quick reaction and low operation costs. The results of the pilot test are consistent with those of laboratory experiments.

  16. Separation of Lead from Crude Antimony by Pyro-Refining Process with NaPO3 Addition

    Science.gov (United States)

    Ye, Longgang; Hu, Yuejie; Xia, Zhimei; Chen, Yongming

    2016-06-01

    The main purpose of this study was to separate lead from crude antimony through an oxidation pyro-refining process and by using sodium metaphosphate as a lead elimination reagent. The process parameters that will affect the refining results were optimized experimentally under controlled conditions, such as the sodium metaphosphate charging dosage, the refining temperature and duration, and the air flow rate, to determine their effect on the lead content in refined antimony and the lead removal rate. A minimum lead content of 0.0522 wt.% and a 98.6% lead removal rate were obtained under the following optimal conditions: W_{{{NaPO}_{{3}} }} = 15% W Sb (where W represents weight), a refining temperature of 800°C, a refining time of 30 min, and an air flow rate of 3 L/min. X-ray diffractometry and scanning electron microscopy showed that high-purity antimony was obtained. The smelting operation is free from smoke or ammonia pollution when using monobasic sodium phosphate or ammonium dihydrogen phosphate as the lead elimination reagent. However, this refining process can also remove a certain amount of sulfur, cobalt, and silicon simultaneously, and smelting results also suggest that sodium metaphosphate can be used as a potential lead elimination reagent for bismuth and copper refining.

  17. PANCREATIC TOXICITY AS AN ADVERSE EFFECT INDUCED BY MEGLUMINE ANTIMONIATE THERAPY IN A CLINICAL TRIAL FOR CUTANEOUS LEISHMANIASIS

    Science.gov (United States)

    LYRA, Marcelo Rosandiski; PASSOS, Sonia Regina Lambert; PIMENTEL, Maria Inês Fernandes; BEDOYA-PACHECO, Sandro Javier; VALETE-ROSALINO, Cláudia Maria; VASCONCELLOS, Erica Camargo Ferreira; ANTONIO, Liliane Fatima; SAHEKI, Mauricio Naoto; SALGUEIRO, Mariza Mattos; SANTOS, Ginelza Peres Lima; RIBEIRO, Madelon Noato; CONCEIÇÃO-SILVA, Fatima; MADEIRA, Maria Fatima; SILVA, Jorge Luiz Nunes; FAGUNDES, Aline; SCHUBACH, Armando Oliveria

    2016-01-01

    SUMMARY American tegumentary leishmaniasis is an infectious disease caused by a protozoan of the genus Leishmania. Pentavalent antimonials are the first choice drugs for cutaneous leishmaniasis (CL), although doses are controversial. In a clinical trial for CL we investigated the occurrence of pancreatic toxicity with different schedules of treatment with meglumine antimoniate (MA). Seventy-two patients were allocated in two different therapeutic groups: 20 or 5 mg of pentavalent antimony (Sb5+)/kg/day for 20 or 30 days, respectively. Looking for adverse effects, patients were asked about abdominal pain, nausea, vomiting or anorexia in each medical visit. We performed physical examinations and collected blood to evaluate serum amylase and lipase in the pre-treatment period, and every 10 days during treatment and one month post-treatment. Hyperlipasemia occurred in 54.8% and hyperamylasemia in 19.4% patients. Patients treated with MA 20 mg Sb5+ presented a higher risk of hyperlipasemia (p = 0.023). Besides, higher MA doses were associated with a 2.05 higher risk ratio (p = 0.003) of developing more serious (moderate to severe) hyperlipasemia. The attributable fraction was 51% in this group. Thirty-six patients presented abdominal pain, nausea, vomiting or anorexia but only 47.2% of those had hyperlipasemia and/ or hyperamylasemia. These findings suggest the importance of the search for less toxic therapeutic regimens for the treatment of CL. PMID:27680173

  18. A study on low cost-high conducting fluorine and antimony-doped tin oxide thin films

    International Nuclear Information System (INIS)

    Thin films of undoped, fluorine- and antimony-doped tin oxide on glass at 400 deg. C was prepared by spray pyrolysis technique. Tin chloride (SnCl2), ammonium fluoride (NH4F), and antimony trichloride (SbCl3) were used as source for tin (Sn), fluorine (F), and antimony (Sb), respectively. To ensure the control of solution concentration on growth rate, fluorine-doped tin oxide (SnO2:F) thin films were first prepared with different amount of tin precursor, in the range of 5-12g, which has resulted in deposition of films with different thickness values. The optimum amount of tin precursor found from this study (11g) was fixed constant for preparing SnO2 films with different doping levels of F and Sb. From the X-ray diffraction analyses, it is understood that the preferred orientation of SnO2:F films is dependent on their thickness and the solution concentration. The variation in the solution concentration and orientation of the films was reflected in their morphology as examined by scanning electron microscopy (SEM) and atomic force microscopy (AFM). SEM studies showed that the variation in the solution concentration lead to different grain shapes for different orientations. The AFM study showed that the RMS roughness of undoped films reduced considerably from 86 to 24nm due to fluorine doping (15wt.%), whereas the antimony doping (2wt.%) has no significance effect on RMS roughness (93nm). The electrical properties of the films were examined by a Hall measurements setup in van der Pauw configuration. A minimum sheet resistance of 1.75 and 2.17Ω/ were obtained for F and Sb doped films, respectively. From the optical studies, it is found that the transmittance of undoped films increased from 42% to a maximum 85% on 30wt.% fluorine doping, whereas that has been decreased to a minimum of 12% on 4wt.% antimony doping (800nm). A discussion on the effect of type of dopants and their concentration on the structural, electrical and optical properties of the SnO2 film have

  19. Preparation of antimony sulfide semiconductor nanoparticles by pulsed laser ablation in liquid

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Ren-De, E-mail: son003@sekisui.com [Research & Development Institute, High Performance Plastics Company, Sekisui Chemical Co., Ltd. 2-1 Hyakuyama, Shimamoto-Cho, Mishima-Gun, Osaka, 618-0021 (Japan); Tsuji, Takeshi [Interdisciplinary Graduate School of Science and Engineering, Shimane University, 1060 Nishikawatsu-Cho, Matsue, 690-8504 (Japan)

    2015-09-01

    Highlights: • Pulsed laser ablation in liquid (LAL) was applied to prepare antimony sulfide nanoparticles (Sb{sub 2}S{sub 3} NPs). • Sb{sub 2}S{sub 3} NPs with a stoichiometric composition were successfully prepared by LAL in water without using any surfactants or capping agents. • Thus-prepared Sb{sub 2}S{sub 3} NPs showed low-temperature crystallization and melting at a temperature low as 200 °C. • The NPs-coated Sb{sub 2}S{sub 3} thin film showed comparable semiconductor properties (carrier mobility and carrier density) to the vacuum deposited one. • Byproducts such as CS{sub 2}, CH{sub 4} and CO were detected by GC-MS analysis when LAL was performed in organic solvent. • The LAL-induced decomposition mechanism of Sb{sub 2}S{sub 3} and organic solvents was discussed based on the GC-MS results. - Abstract: In this paper, we report on the synthesis of antimony sulfide (Sb{sub 2}S{sub 3}) semiconductor nanoparticles by pulsed laser ablation in liquid without using any surfactants or capping agents. Different results were obtained in water and organic solvents. In the case of water, Sb{sub 2}S{sub 3} nanoparticles with chemical compositions of stoichiometry were successfully prepared when laser irradiation was performed under the condition with the dissolved oxygen removed by argon gas bubbling. It was shown that thus-obtained Sb{sub 2}S{sub 3} nanoparticles exhibit features of not only low-temperature crystallization but also low-temperature melting at a temperature as low as 200 °C. Nanoparticle-coated Sb{sub 2}S{sub 3} thin films were found to show good visible light absorption and satisfying semiconductor properties (i.e., carrier mobility and density), which are essential for photovoltaic application. On the other hand, in the case of organic solvents (e.g., acetone, ethanol), such unexpected byproducts as CS{sub 2}, CO and CH{sub 4} were detected from the reaction system by GC-MS analysis, which suggests that both Sb{sub 2}S{sub 3} and organic

  20. Infrared-to-red upconversion luminescence in samarium-doped antimony glasses

    Energy Technology Data Exchange (ETDEWEB)

    Som, Tirtha [Glass Technology Laboratory, Glass Division, Central Glass and Ceramic Research Institute, 196 Raja S.C. Mullick Road, Kolkata 700 032 (India); Karmakar, Basudeb [Glass Technology Laboratory, Glass Division, Central Glass and Ceramic Research Institute, 196 Raja S.C. Mullick Road, Kolkata 700 032 (India)], E-mail: basudebk@cgcri.res.in

    2008-12-15

    A new antimony-based glass system (K{sub 2}O-B{sub 2}O{sub 3}-Sb{sub 2}O{sub 3}) having low phonon energy (about 600 cm{sup -1}) doped with Sm{sup 3+} ions has been developed. Infrared reflection spectroscopic (IRRS) studies have been employed to establish its low phonon energy. Ultraviolet-Visible-near infrared (UV-Vis-NIR) absorption and photoluminescence upconversion properties with the spectrochemistry of the 15K{sub 2}O-15B{sub 2}O{sub 3}-70Sb{sub 2}O{sub 3} (mol%) glasses have been studied doping with different concentrations (0.1-1.0 wt%) of Sm{sub 2}O{sub 3}. UV-Vis-NIR absorption band positions have been justified with quantitative calculation of nephelauxetic parameter and covalent bonding characteristics of the host. NIR to visible upconversion has been investigated by exciting at 949 nm at room temperature. Three upconverted bands originating from the {sup 4}G{sub 5/2}{yields}{sup 6}H{sub 5/2}, {sup 4}G{sub 5/2}{yields}{sup 6}H{sub 7/2} and {sup 4}G{sub 5/2}{yields}{sup 6}H{sub 9/2} transitions are found to be centered at 566 (green, weak), 602 (orange, weak) and 636 (red, remarkably strong) nm, respectively. These bands have been explained from the evaluation of the absorption, normal (downconversion) fluorescence and excitation spectra. The upconversion processes have been explained by the excited state absorption (ESA), energy transfer (ET) and cross-relaxation (CR) mechanisms involving population of the metastable (storage) energy level ({sup 4}G{sub 5/2}) by multiphonon deexcitation effect. It is evident from the IRRS study that the upconversion phenomena are expedited by the low multiphonon relaxation rate in antimony glasses owing to their low phonon energy (602 cm{sup -1}, the main and highest intensity Sb-O-Sb stretching band) which is very close to that of fluoride glasses (500-600 cm{sup -1})

  1. Inhibition of Leishmania donovani promastigote DNA topoisomerase I and human monocyte DNA topoisomerases I and II by antimonial drugs and classical antitopoisomerase agents.

    Science.gov (United States)

    Walker, John; Saravia, Nancy G

    2004-10-01

    We have compared the inhibitor sensitivities of DNA topoisomerase I (TOPI) from Leishmania donovani promastigotes and TOPs I and II of human monocytes using pentavalent and trivalent antimonials (SbV, SbIII) and classical TOP inhibitors. Bis-benzimidazoles (Hoechst-33258 and -33342) were potent inhibitors of both parasite and human TOPI, but Hoechst-33342 was markedly less cytotoxic to promastigotes than to monocytes in vitro. Leishmania donovani was also considerably less sensitive than monocytes to camptothecin, both at enzyme and cellular levels. Sodium stibogluconate (SSG) was the only antimonial to inhibit TOPI, exhibiting a significant (P donovani enzyme but showed low cytotoxicities against intact promastigotes. The SbV meglumine antimoniate failed to inhibit TOPI and showed negligible cytotoxicities, whereas SbIII drugs were lethal to parasites and monocytes yet poor inhibitors of TOPI. Monocyte TOPII was inhibited by bis-benzimidazoles and insensitive to antimonials and camptothecin. The disparity between the high leishmanicidal activity and low anti-TOPI potency of SbIII indicates that in vivo targeting of L. donovani TOPI by the reductive pathway of antimonial activation is improbable. Nevertheless, the potent direct inhibition of TOPI by SSG and the differential interactions of camptothecin with L. donovani and human TOPI support the possibility of developing parasite-specific derivatives. PMID:15562618

  2. Leaching of Antimony (Sb)from Municipal Solid Waste Incineration (MSWI) Residues

    Energy Technology Data Exchange (ETDEWEB)

    Herrmann, Inga

    2004-07-01

    The mobility of antimony (Sb) in municipal solid waste incineration (MSWI) residues often exceeds the limit values stipulated by the European Union. As an ash treatment by washing is conceivable, this work investigated the Sb release from Swedish bottom ash and fly ash when mixed with water. The leaching experiments revealed the factors significantly (a = 0.05) affecting Sb release from the ashes. The following factors were investigated: Liquid to solid ratio (L/S), time, pH, carbonation (treatment with CO{sub 2}), ultrasonics and temperature. The data were evaluated using multiple linear regression (MLR). The impact of the factors could be quantified. The maximum Sb release calculated was 13 mg/kg DM for bottom ash and 51 mg/kg DM for fly ash. The derived models explained the observed data well. Nevertheless, the calculated values were subject to a high uncertainty. For bottom ash, a lowering of the Sb total content of approximately 22% could be achieved. If this also involves a sufficient lowering of the Sb mobility to meet EU limit values could not yet be assessed. Chemical equilibrium calculations were performed to explain the empirical results. However, no solid phases controlling Sb release from the ashes could be identified.

  3. Synthesis of Copper-Antimony-Sulfide Nanocrystals for Solution-Processed Solar Cells.

    Science.gov (United States)

    Suehiro, Satoshi; Horita, Keisuke; Yuasa, Masayoshi; Tanaka, Tooru; Fujita, Katsuhiko; Ishiwata, Yoichi; Shimanoe, Kengo; Kida, Tetsuya

    2015-08-17

    The p-type nanocrystals (NCs) of copper-based chalcogenides, such as CuInSe2 and Cu2ZnSnS4, have attracted increasing attention in photovoltaic applications due to their potential to produce cheap solution-processed solar cells. Herein, we report the synthesis of copper-antimony-sulfide (CAS) NCs with different crystal phases including CuSbS2, Cu3SbS4, and Cu12Sb4S13. In addition, their morphology, crystal phase, and optical properties were characterized using transmission electron microscopy, X-ray diffractometry, UV-vis-near-IR spectroscopy, and photoemission yield spectroscopy. The morphology, crystal phase, and electronic structure were significantly dependent on the chemical composition in the CAS system. Devices were fabricated using particulate films consisting of CAS NCs prepared by spin coating without a high-temperature treatment. The CAS NC-based devices exhibited a diode-like current-voltage characteristic when coupled with an n-type CdS layer. In particular, the CuSbS2 NC devices exhibited photovoltaic responses under simulated sunlight, demonstrating its applicability for use in solution-processed solar cells. PMID:26237216

  4. Direct Band Gap Gallium Antimony Phosphide (GaSbxP(1-x)) Alloys.

    Science.gov (United States)

    Russell, H B; Andriotis, A N; Menon, M; Jasinski, J B; Martinez-Garcia, A; Sunkara, M K

    2016-01-01

    Here, we report direct band gap transition for Gallium Phosphide (GaP) when alloyed with just 1-2 at% antimony (Sb) utilizing both density functional theory based computations and experiments. First principles density functional theory calculations of GaSbxP(1-x) alloys in a 216 atom supercell configuration indicate that an indirect to direct band gap transition occurs at x = 0.0092 or higher Sb incorporation into GaSbxP(1-x). Furthermore, these calculations indicate band edge straddling of the hydrogen evolution and oxygen evolution reactions for compositions ranging from x = 0.0092 Sb up to at least x = 0.065 Sb making it a candidate for use in a Schottky type photoelectrochemical water splitting device. GaSbxP(1-x) nanowires were synthesized by reactive transport utilizing a microwave plasma discharge with average compositions ranging from x = 0.06 to x = 0.12 Sb and direct band gaps between 2.21 eV and 1.33 eV. Photoelectrochemical experiments show that the material is photoactive with p-type conductivity. This study brings attention to a relatively uninvestigated, tunable band gap semiconductor system with tremendous potential in many fields. PMID:26860470

  5. Direct Band Gap Gallium Antimony Phosphide (GaSbxP1-x) Alloys

    Science.gov (United States)

    Russell, H. B.; Andriotis, A. N.; Menon, M.; Jasinski, J. B.; Martinez-Garcia, A.; Sunkara, M. K.

    2016-02-01

    Here, we report direct band gap transition for Gallium Phosphide (GaP) when alloyed with just 1-2 at% antimony (Sb) utilizing both density functional theory based computations and experiments. First principles density functional theory calculations of GaSbxP1-x alloys in a 216 atom supercell configuration indicate that an indirect to direct band gap transition occurs at x = 0.0092 or higher Sb incorporation into GaSbxP1-x. Furthermore, these calculations indicate band edge straddling of the hydrogen evolution and oxygen evolution reactions for compositions ranging from x = 0.0092 Sb up to at least x = 0.065 Sb making it a candidate for use in a Schottky type photoelectrochemical water splitting device. GaSbxP1-x nanowires were synthesized by reactive transport utilizing a microwave plasma discharge with average compositions ranging from x = 0.06 to x = 0.12 Sb and direct band gaps between 2.21 eV and 1.33 eV. Photoelectrochemical experiments show that the material is photoactive with p-type conductivity. This study brings attention to a relatively uninvestigated, tunable band gap semiconductor system with tremendous potential in many fields.

  6. Large anharmonic effect and thermal expansion anisotropy of metal chalcogenides: The case of antimony sulfide

    Science.gov (United States)

    Gan, Chee Kwan; Soh, Jian Rui; Liu, Yun

    2015-12-01

    We derive a compact matrix expression for the linear thermal expansion coefficients (TECs) for a general orthorhombic system which relates elastic properties and integrated quantities based on deformation and mode dependent Grüneisen parameters and mode dependent heat capacities. The density of Grüneisen parameters Γ (ν ) as a function of frequency ν , weighted by the number of phonon modes, is introduced and found to be illuminating in interpreting the TEC results. Using density functional perturbation theory and Grüneisen formalism for thermal expansion, we illustrate the general usefulness of this method by calculating the linear and volumetric TECs of a low-symmetry orthorhombic compound antimony sulfide (Sb2S3 ), which belongs to a large class of technologically and fundamentally important materials. Even though negative Grüneisen parameters are found for deformations in all three crystal directions, the Γ (ν ) data rule out the occurrences of negative TECs at all temperatures. Sb2S3 exhibits a large thermal expansion anisotropy where the TEC in the b direction can reach as high as 13 ×10-6 K-1 at high temperatures, about two and seven times larger than the TECs in the c and a direction, respectively. Our work suggests a general and practical first-principles approach to calculate the thermal properties of other complicated low-symmetry systems.

  7. Controlled n-doping in chemical vapour deposition grown graphene by antimony

    International Nuclear Information System (INIS)

    We have studied the effects of antimony (Sb) doping on graphene grown by chemical vapour deposition without any significant change in its electrical properties. By increasing the metal thickness from 1 to 5 nm, we found a shift in the wave numbers of Raman G and two-dimensional (2D) peaks consistent with n-doping and a change in the Fermi level of the graphene into the conduction band. The relative intensity of the D peak to the G peak did not show a significant change and that of the 2D peak to the G peak remained at a large enough number as a function of metal thickness, implying little degradation by the metal dopants. Transport measurements also confirm the n-doping of graphene through a shift of Dirac point in the transfer characteristics and the quality preservation with little changes in mobility. We also report on the formation of a p–n junction by metal doping on selected areas of the graphene and their electrical properties with transfer characteristics and Hall measurements. (paper)

  8. Evaluation of atmospheric inputs as possible sources of antimony in pregnant women from urban areas.

    Science.gov (United States)

    Fort, Marta; Grimalt, Joan O; Querol, Xavier; Casas, Maribel; Sunyer, Jordi

    2016-02-15

    Antimony and copper are common components of brake linings. The occurrence of these two metals in urban atmospheric aerosols has been related to vehicular use. Urine samples (n=466) taken during the 32nd week of pregnancy were analyzed for Sb and Cu in pregnant women from an urban area (Sabadell, Catalonia, Spain). The geometric mean levels were 0.28 and 13 μg/g creatinine, respectively. Positive significant associations between urine concentrations of Sb and seasonality, intensity of physical exercise, working activities and traffic intensity at their home streets were observed. Cu showed the same trends but without statistical significance. In both cases, the estimated dietary ingestion of these two metals was larger than the inhalation inputs but the difference was much higher for Cu than for Sb. While Sb has no dietary role, Cu is an essential element which is also incorporated into humans through diet. The results suggest that inhalation of atmospheric particles may also constitute a source of Sb in pregnant women and general population of urban areas. PMID:26657384

  9. Partitioning geochemistry of arsenic and antimony, El Tatio Geyser Field, Chile

    Energy Technology Data Exchange (ETDEWEB)

    Landrum, J.T. [Department of Geological Sciences, The University of Texas, Austin, TX 78759 (United States); Bennett, P.C., E-mail: pbennett@mail.utexas.edu [Department of Geological Sciences, University of Texas, Austin, TX 78759 (United States); Engel, A.S. [Department of Geology and Geophysics, Louisiana State University, Baton Rouge, LA 70803 (United States); Alsina, M.A.; Pasten, P.A. [Departamento de Ingenieria Hidraulica y Ambiental, Pontificia Universidad Catolica de Chile, Santiago (Chile); Milliken, K. [Department of Geological Sciences, University of Texas, Austin, TX 78759 (United States)

    2009-04-15

    The abundance of As and Sb in aqueous, mineral and biological reservoirs was examined at El Tatio Geyser Field, a unique hydrothermal basin located in the Atacama Desert region of Chile. Here the concentration of total As and Sb in hydrothermal springs and discharge streams are the highest reported for a natural surface water, and the geyser basin represents a significant source of toxic elements for downstream users across Region II, Chile. The geyser waters are near neutral Na:Cl type with {approx}0.45 and 0.021 mmol L{sup -1} total As and Sb, respectively, primarily in the reduced (III) redox state at the discharge with progressive oxidation downstream. The ferric oxyhydroxides associated with the microbial mats and some mineral precipitates accumulate substantial As that was identified as arsenate by XAS analysis (>10 wt% in the mats). This As is easily mobilized by anion exchange or mild dissolution of the HFO, and the ubiquitous microbial mats represent a significant reservoir of As in this system. Antimony, in contrast, is not associated with the mineral ferric oxides or the biomats, but is substantially enriched in the silica matrix of the geyserite precipitates, up to 2 wt% as Sb{sub 2}O{sub 3}. Understanding the mobility and partitioning behavior of these metalloids is critical for understanding their eventual impact on regional water management.

  10. Spark Plasma Sintering and Densification Mechanisms of Antimony-Doped Tin Oxide Nanoceramics

    Directory of Open Access Journals (Sweden)

    Junyan Wu

    2013-01-01

    Full Text Available Densification of antimony-doped tin oxide (ATO ceramics without sintering aids is very difficult, due to the volatilization of SnO2, formation of deleterious phases above 1000°C, and poor sintering ability of ATO particles. In this paper, monodispersed ATO nanoparticles were synthesized via sol-gel method, and then ATO nanoceramics with high density were prepared by spark plasma sintering (SPS technology using the as-synthesized ATO nanoparticles without the addition of sintering aids. The effect of Sb doping content on the densification was investigated, and the densification mechanisms were explored. The results suggest that ATO nanoparticles derived from sol-gel method show good crystallinity with a crystal size of 5–20 nm and Sb is incorporated into the SnO2 crystal structure. When the SPS sintering temperature is 1000°C and the Sb doping content is 5 at.%, the density of ATO nanoceramics reaches a maximum value of 99.2%. Densification mechanisms are explored in detail.

  11. Antimony release from contaminated mine soils and its migration in four typical soils using lysimeter experiments.

    Science.gov (United States)

    Shangguan, Yu-Xian; Zhao, Long; Qin, Yusheng; Hou, Hong; Zhang, Naiming

    2016-11-01

    Antimony (Sb) can pose great risks to the environment in mining and smelting areas. The migration of Sb in contaminated mine soil was studied using lysimeter experiments. The exchangeable concentration of soil Sb decreased with artificial leaching. The concentrations of Sb retained in the subsoil layers (5-25cm deep) were the highest for Isohumosol and Ferrosol and the lowest for Sandy soil. The Sb concentrations in soil solutions decreased with soil depth, and were adequately simulated using a logarithmic function. The Sb migration pattern in Sandy soil was markedly different from the patterns in the other soils which suggested that Sb may be transported in soil colloids. Environmental factors such as water content, soil temperature, and oxidation-reduction potential of the soil had different effects on Sb migration in Sandy soil and Primosol. The high Fe and Mn contents in Ferrosol and Isohumosol significantly decreased the mobility of Sb in these soils. The Na and Sb concentrations in soils used in the experiments positively correlated with each other (Psoil solutions, the Sb chemical fraction patterns, and the Sb/Na ratios decreased in the order Sandy soil>Primosol>Isohumosol>Ferrosol, and we concluded that the Sb mobility in the soils also decreased in that order. PMID:27395817

  12. Synthesis of Copper-Antimony-Sulfide Nanocrystals for Solution-Processed Solar Cells.

    Science.gov (United States)

    Suehiro, Satoshi; Horita, Keisuke; Yuasa, Masayoshi; Tanaka, Tooru; Fujita, Katsuhiko; Ishiwata, Yoichi; Shimanoe, Kengo; Kida, Tetsuya

    2015-08-17

    The p-type nanocrystals (NCs) of copper-based chalcogenides, such as CuInSe2 and Cu2ZnSnS4, have attracted increasing attention in photovoltaic applications due to their potential to produce cheap solution-processed solar cells. Herein, we report the synthesis of copper-antimony-sulfide (CAS) NCs with different crystal phases including CuSbS2, Cu3SbS4, and Cu12Sb4S13. In addition, their morphology, crystal phase, and optical properties were characterized using transmission electron microscopy, X-ray diffractometry, UV-vis-near-IR spectroscopy, and photoemission yield spectroscopy. The morphology, crystal phase, and electronic structure were significantly dependent on the chemical composition in the CAS system. Devices were fabricated using particulate films consisting of CAS NCs prepared by spin coating without a high-temperature treatment. The CAS NC-based devices exhibited a diode-like current-voltage characteristic when coupled with an n-type CdS layer. In particular, the CuSbS2 NC devices exhibited photovoltaic responses under simulated sunlight, demonstrating its applicability for use in solution-processed solar cells.

  13. Assessment and distribution of antimony in soils around three coal mines, Anhui, China

    Science.gov (United States)

    Qi, C.; Liu, Gaisheng; Kang, Y.; Lam, P.K.S.; Chou, C.

    2011-01-01

    Thirty-three soil samples were collected from the Luling, Liuer, and Zhangji coal mines in the Huaibei and Huainan areas of Anhui Province, China. The samples were analyzed for antimony (Sb) by inductively coupled plasmaoptical emission spectrometry (ICP-OES) method. The average Sb content in the 33 samples was 4 mg kg-1, which is lower than in coals from this region (6.2 mg kg-1). More than 75% of the soils sampled showed a significant degree of Sb pollution (enrichment factors [EFs] 5-20). The soils collected near the gob pile and coal preparation plant were higher in Sb content than those collected from residential areas near the mines. The gob pile and tailings from the preparation plant were high in mineral matter content and high in Sb. They are the sources of Sb pollution in surface soils in the vicinity of coal mines. The spatial dispersion of Sb in surface soil in the mine region shows that Sb pollution could reach out as far as 350 m into the local environment conditions. Crops in rice paddies may adsorb some Sb and reduce the Sb content in soils from paddyfields. Vertical distribution of Sb in two soil profiles indicates that Sb is normally relatively immobile in soils. ?? 2011 Air & Waste Management Association.

  14. DFT Study on the Carrier Concentration and Temperature-Dependent Thermoelectric Properties of Antimony Selenide

    Directory of Open Access Journals (Sweden)

    Aditya Jayaraman

    2016-01-01

    Full Text Available We present the thermoelectric properties of Antimony Selenide (Sb2Se3 obtained using first principles calculations. We investigated the electronic band structure using the FP-LAPW method within the sphere of the density functional theory. Thermoelectric properties were calculated using BoltzTrap code using the constant relaxation time (τ approximation at three different temperatures 300 K, 600 K, and 800 K. Seebeck coefficient (S was found to decrease with increasing temperature, electrical conductivity (σ/τ was almost constant in the entire temperature range, and electronic thermal conductivity (κ/τ increased with increasing temperature. With increase in temperature S decreased from 1870 μV/K (at 300 K to 719 μV/K (at 800 K, electronic thermal conductivity increased from 1.56 × 1015 W/m K s (at 300 K to 3.92 × 1015 W/m K s (at 800 K, and electrical conductivity decreased from 22 × 1019/Ω m s (at 300 K to 20 × 1019/Ω m s (at 800 K. The thermoelectric properties were also calculated for different hole concentrations and the optimum concentration for a good thermoelectric performance over a large range of temperatures (from 300 K to 1000 K was found for hole concentration around 1019 cm−3.

  15. Comparison of arsenic and antimony biogeochemical behavior in water, soil and tailings from Xikuangshan, China.

    Science.gov (United States)

    Fu, Zhiyou; Wu, Fengchang; Mo, Changli; Deng, Qiujing; Meng, Wei; Giesy, John P

    2016-01-01

    Although similar geochemical behaviors of arsenic (As) and antimony (Sb) in the environment has been assumed and widely reported, growing evidence suggests the two elements cannot, under some conditions, be assumed to behave similarly. In this four-year study (samples collected in each year), comparative investigation of the biogeochemistry of As and Sb in water/fish, soil/vegetable, tailings/plant samples were carried out at the world's largest active Sb mine area (Xikuangshan, China). Depending on duration the tailings had been stacked, significant differences in spatial distributions between As and Sb were found, and these were associated with change in pH over time. Bio-accumulation factors (BAFs) of As were approximately 10-fold greater than those of Sb in fish/water, plant/tailing, and vegetable/soil systems. Sb had higher BAF in non-fatty tissues such as gills of fishes and shells of crabs. BAFs of Sb in vegetable/soil exhibited insignificantly, but different from As, positive correlation with pH in soil. PMID:26356182

  16. Validation of methodology and uncertainty assessment of antimony determination in environmental materials using Neutron Activation Analysis

    International Nuclear Information System (INIS)

    Antimony is an element found in low concentrations in the environment. However, its determination has attracted great interest because of the knowledge of its toxicity and increasing application. Neutron activation analysis (NAA) is a suitable method for the determination of several elements in different types, but in case of Sb, the analysis presents some difficulties due to spectral interferences. The objective of this research was to validate the method of NAA and uncertainty assessment for Sb determination in environmental samples. The experimental procedure consisted of irradiating twelve certified reference samples of different kind of matrices. The samples were irradiated in the nuclear research reactor IEA R1 IPEN/CNEN/SP followed by measurement of induced radioactivity, using a hyperpure germanium detector coupled to a gamma ray spectrometry. The radioisotopes 122Sb and 124Sb were measured and the Sb concentrations with their respective uncertainties were obtained by the comparative method. Relative errors and values of Z scores were calculated to evaluate the accuracy of the results for Sb determination in certified reference materials. The evaluation of the components that contribute to uncertainty measurement of the Sb concentration, showed that the major uncertainty contribution is due to statistical counting. The results also indicated that the uncertainty value of the combined standard uncertainty depends on the radioisotope measured and the decay time used for counting. (author)

  17. Antimony-Doped Tin Oxide Thin Films Grown by Home Made Spray Pyrolysis Technique

    Science.gov (United States)

    Yusuf, Gbadebo; Babatola, Babatunde Keji; Ishola, Abdulahi Dimeji; Awodugba, Ayodeji O.; Solar cell Collaboration

    2016-03-01

    Transparent conducting antimony-doped tin oxide (ATO) films have been deposited on glass substrates by home made spray pyrolysis technique. The structural, electrical and optical properties of the ATO films have been investigated as a function of Sb-doping level and annealing temperature. The optimum target composition for high conductivity and low resistivity was found to be 20 wt. % SnSb2 + 90 wt. ATO. Under optimized deposition conditions of 450oC annealing temperature, electrical resistivity of 5.2×10-4 Ω -cm, sheet resistance of 16.4 Ω/sq, average optical transmittance of 86% in the visible range, and average optical band-gap of 3.34eV were obtained. The film deposited at lower annealing temperature shows a relatively rough, loosely bound slightly porous surface morphology while the film deposited at higher annealing temperature shows uniformly distributed grains of greater size. Keywords: Annealing, Doping, Homemade spray pyrolysis, Tin oxide, Resistivity

  18. A density-functional study on the electronic and vibrational properties of layered antimony telluride

    Science.gov (United States)

    Stoffel, Ralf P.; Deringer, Volker L.; Simon, Ronnie E.; Hermann, Raphaël P.; Dronskowski, Richard

    2015-03-01

    We present a comprehensive survey of electronic and lattice-dynamical properties of crystalline antimony telluride (Sb2Te3). In a first step, the electronic structure and chemical bonding have been investigated, followed by calculations of the atomic force constants, phonon dispersion relationships and densities of states. Then, (macroscopic) physical properties of Sb2Te3 have been computed, namely, the atomic thermal displacement parameters, the Grüneisen parameter γ, the volume expansion of the lattice, and finally the bulk modulus B. We compare theoretical results from three popular and economic density-functional theory (DFT) approaches: the local density approximation (LDA), the generalized gradient approximation (GGA), and a posteriori dispersion corrections to the latter. Despite its simplicity, the LDA shows excellent performance for all properties investigated—including the Grüneisen parameter, which only the LDA is able to recover with confidence. In the absence of computationally more demanding hybrid DFT methods, the LDA seems to be a good choice for further lattice dynamical studies of Sb2Te3 and related layered telluride materials.

  19. Gold and Antimony Mixed Flotation on a Micrite Gold Antimony ore in Guizhou%贵州某泥晶灰岩型含锑金矿金锑混浮试验

    Institute of Scientific and Technical Information of China (English)

    石贵明; 周意超

    2015-01-01

    贵州某泥晶灰岩型含锑金矿石为块状构造,金属矿物主要为黄铁矿、针铁矿,含量小于1%,非金属矿物以方解石为主,另有少量石英、有机质等;金含量为6.04 g/t,显微镜下未见自然金粒,74.34%的金赋存在硫化矿中,游离金仅占总金的7.14%;硅酸盐、碳酸盐包裹金分别占11.96%和6.56%;锑主要以辉锑矿的形式存在。为高效、低成本回收矿石中的金、锑,对混合浮选工艺进行了试验研究。结果表明,在一段磨矿细度为-0.074 mm占71%的情况下1粗2扫混浮、尾矿再磨细度为-0.074 mm占92.7%的情况下再1粗2扫混浮、两粗精矿合并后3次精选、中矿顺序返回流程处理,最终获得了金品位为47.60 g/t、锑品位为9.81%、金回收率为76.68%、锑回收率为85.22%的金锑混合精矿,金锑混浮效果较理想。尾矿中金的回收及金锑分离工艺研究将另文介绍。%The micrite type antimony-containing gold ore in Guizhou is in blocky construction. Its metallic minerals are mainly pyrite and goethite,with content of less than 1%. Non-metallic minerals are calcite,and few of quartz,organic matter, etc. It contains gold of 6. 04 g/t,and natural gold grains were not seen in microscope,74. 34% of the gold occurred in sulfide ore,free gold accounted for only 7. 14%,wrapped gold in silicate and carbonate accounted for 11. 96% and 6. 56% respective-ly. Antimony mainly existed in the form of stibnite. Bulk flotation process was studied to make high efficient recovery of gold and antimony at low costs. The results indicated that,at the grinding fineness of 71% passing 0. 074 mm,through one roughing and two scavenging bulk flotation,one roughing and two scavenging bulk flotation after regrinding the tailings to 92. 7% passing 0. 074 mm,three cleaning flotation for the two mixed rough concentrate,and then middles back to the flow-sheet in turn,rough gold-antimony concentrate with gold grade of 47. 60 g

  20. Supramolecular association via Sb...S and C-H...S interactions in dimeric tris(N,N-dimethyldithiocarbamato-S,S')antimony(III): an approach to overcome the concept of steric bulk on such interactions.

    Science.gov (United States)

    Chauhan, H P S; Carpenter, Jaswant

    2013-12-01

    Tris(N,N-dimethyldithiocarbamato-S,S')antimony(III) has been isolated as a dimer in acetonitrile. Single-crystal X-ray analysis shows that the molecule possesses both Sb···S and C-H···S interactions, which results in a supramolecular association in the absence of hydrogen-bonding functionality on the R group. The co-existence in the title compound of such interactions is a unique character of known dimeric antimony(III) alkyl and/or aryl dithiocarbamate complexes. The literature reveals that the species where the alkyl and/or aryl dithiocarbamates carry the following groups: R = methyl (chloroform solvated), ethyl, n-propyl, pyrrolidine, morpholine, piperidine, azepane, benzyl, methylphenyl, are not capable of forming significant hydrogen-bonding interactions. However, either Sb···S or C-H···S intermolecular interactions dominate between two centrosymmetrically related molecules leading to a supramolecular aggregation. In the species where the R group carries hydrogen-bonding functionality, i.e. 2-hydroxylethyl, the C-H···S interactions are subverted by O-H···O hydrogen bonding. In addition, the title compound does not have steric hindrance or any hydrogen-bonding group but is stabilized with the co-existence of Sb···S and C-H···S interactions. Analysis of the secondary interactions of a series of analogues previously reported reveals that steric bulk is unnecessary for the mitigation of Sb···S interactions and for the establishment of C-H···S secondary bonding. PMID:24253087

  1. Minerogenetic Mechanism of the Songxi Silver—Antimony Deposit of Northeastern Guangdong—Ore—Controlling Role of Organic Matter

    Institute of Scientific and Technical Information of China (English)

    胡凯; 肖振宇; 等

    1999-01-01

    Organic geochemistry and comparisons of characteristics of the organic matter in wall rocks of the ore-controlling strata and ores of the Lower Jurassic Songling black shale formation and the related Songxi silver-antimony deposit of northeastern Guangdong have been studied in this paper.The results show that the Lower Jurassic Songling shale formation is a suite of biologic-rich and organic-rich ore-bearing marine sedimentary rocks.Micro-components of the organic matter in the Songling black shale formation consists primarily of algae,amorphous marine kerogen,solid bitument,and pyrobitument.The thermal evolution of organic matter is at the over-maturity stage.There is a general positive correlation between total organic carbon(CO)and metallogenetic elements such as Ag and Sb in the black shale formation.Organic matter in the host rocks in the Songxi ore deposit played a role in controlling the silver-antimony depositing environment during the forming process of the black shale ore-bearing formation.In the absence of vitrinite,the relative level of thermal maturity calculated by solid bitument reflectance indicates that the ore-forming temperatute of the Songxi silver-antimony deposit was about 150-170℃,which was considered as an epithermally reworked ore deposit.The roles of organic matter in the formation of the Sonxi ore deposit are a primitive accumulation of the metallogenetic elements(Ag,Sb) in the sea-water cycle system for ore source and a concentration of metals by ion exchange of chelation as well as reductionn of the oxidzed metals.

  2. Clinical and Parasitological Features of Patients with American Cutaneous Leishmaniasis that Did Not Respond to Treatment with Meglumine Antimoniate

    Science.gov (United States)

    Robayo, Marta L.; Lopez, Myriam C.; Daza, Carlos D.; Bedoya, Angela; Mariño, Maria L.; Saavedra, Carlos H.

    2016-01-01

    Background American cutaneous leishmaniasis (ACL) is a complicated disease producing about 67.000 new cases per year. The severity of the disease depends on the parasite species; however in the vast majority of cases species confirmation is not feasible. WHO suggestion for ACL produced by Leishmania braziliensis, as first line treatment, are pentavalent antimonial derivatives (Glucantime or Sodium Stibogluconate) under systemic administration. According to different authors, pentavalent antimonial derivatives as treatment for ACL show a healing rate of about 75% and reasons for treatment failure are not well known. Methods In order to characterise the clinical and parasitological features of patients with ACL that did not respond to Glucantime, a cross-sectional observational study was carried out in a cohort of 43 patients recruited in three of the Colombian Army National reference centers for complicated ACL. Clinical and paraclinical examination, and epidemiological and geographic information were recorded for each patient. Parasitological, histopathological and PCR infection confirmation were performed. Glucantime IC50 and in vitro infectivity for the isolated parasites were estimated. Results Predominant infecting Leishmania species corresponds to L. braziliensis (95.4%) and 35% of the parasites isolated showed a significant decrease in in vitro Glucanatime susceptibility associated with previous administration of the medicament. Lesion size and in vitro infectivity of the parasite are negatively correlated with decline in Glucantime susceptibility (Spearman: r = (-)0,548 and r = (-)0,726; respectively). Conclusion A negative correlation between lesion size and parasite resistance is documented. L. braziliensis was found as the main parasite species associated to lesion of patients that underwent treatment failure or relapse. The indication of a second round of treatment in therapeutic failure of ACL, produced by L. braziliensis, with pentavalent antimonial

  3. Cobalt doped antimony oxide nano-particles based chemical sensor and photo-catalyst for environmental pollutants

    Energy Technology Data Exchange (ETDEWEB)

    Jamal, Aslam [Centre for Advanced Materials and Nano-Engineering (CAMNE) and Department of Chemistry, Faculty of Sciences and Arts, Najran University, P. O. Box 1988, Najran 11001 (Saudi Arabia); Rahman, Mohammed M. [Center of Excellence for Advanced Materials Research (CEAMR), King Abdulaziz University, P.O. Box 80203, Jeddah 21589 (Saudi Arabia); Chemistry Department, Faculty of Science, King Abdulaziz University, P.O. Box 80203, Jeddah 21589 (Saudi Arabia); Khan, Sher Bahadar, E-mail: drkhanmarwat@gmail.com [Center of Excellence for Advanced Materials Research (CEAMR), King Abdulaziz University, P.O. Box 80203, Jeddah 21589 (Saudi Arabia); Chemistry Department, Faculty of Science, King Abdulaziz University, P.O. Box 80203, Jeddah 21589 (Saudi Arabia); Faisal, Mohd. [Centre for Advanced Materials and Nano-Engineering (CAMNE) and Department of Chemistry, Faculty of Sciences and Arts, Najran University, P. O. Box 1988, Najran 11001 (Saudi Arabia); Akhtar, Kalsoom [Division of Nano Sciences and Department of Chemistry, Ewha Womans University, Seoul 120-750 (Korea, Republic of); Rub, Malik Abdul; Asiri, Abdullah M.; Al-Youbi, Abdulrahman O. [Center of Excellence for Advanced Materials Research (CEAMR), King Abdulaziz University, P.O. Box 80203, Jeddah 21589 (Saudi Arabia); Chemistry Department, Faculty of Science, King Abdulaziz University, P.O. Box 80203, Jeddah 21589 (Saudi Arabia)

    2012-11-15

    Graphical abstract: A dichloromethane chemical sensor using cobalt antimony oxides has been fabricated. This sensor showed high sensitivity and will be a useful candidate for environmental and health monitoring. Also it showed high photo-catalytic activity and can be a good candidate as a photo-catalyst for organic hazardous materials. Highlights: Black-Right-Pointing-Pointer Reusable chemical sensor. Black-Right-Pointing-Pointer Green environmental and eco-friendly chemi-sensor. Black-Right-Pointing-Pointer High sensitivity. Black-Right-Pointing-Pointer Good candidate for environmental and health monitoring. - Abstract: Cobalt doped antimony oxide nano-particles (NPs) have been synthesized by hydrothermal process and structurally characterized by utilizing X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM) and Fourier transforms infrared spectrophotometer (FT-IR) which revealed that the synthesized cobalt antimony oxides (CoSb{sub 2}O{sub 6}) are well crystalline nano-particles with an average particles size of 26 {+-} 10 nm. UV-visible absorption spectra ({approx}286 nm) were used to investigate the optical properties of CoSb{sub 2}O{sub 6}. The chemical sensing of CoSb{sub 2}O{sub 6} NPs have been primarily investigated by I-V technique, where dichloromethane is used as a model compound. The analytical performance of dichloromethane chemical sensor exhibits high sensitivity (1.2432 {mu}A cm{sup -2} mM{sup -1}) and a large linear dynamic range (1.0 {mu}M-0.01 M) in short response time (10 s). The photo catalytic activity of the synthesized CoSb{sub 2}O{sub 6} nano-particles was evaluated by degradation of acridine orange (AO), which degraded 58.37% in 200 min. These results indicate that CoSb{sub 2}O{sub 6} nano-particles can play an excellent research impact in the environmental field.

  4. Comparative Efficacies of Two Antimony Regimens To Treat Leishmania braziliensis-Induced Cutaneous Leishmaniasis in Rhesus Macaques (Macaca mulatta)▿

    Science.gov (United States)

    Grimaldi, G.; Porrozzi, R.; Friedrich, K.; Teva, A.; Marchevsky, R. S.; Vieira, F.; Miekeley, N.; Paumgartten, F. J. R.

    2010-01-01

    This study compared the efficacies of two N-methylglucomine antimoniate (MA) dose regimens for treating macaques with Leishmania braziliensis-induced chronic skin disease. Whereas all animals treated with the full dose (20 mg MA/kg/day) were cured, 50% of the monkeys receiving a low-dose regimen (5 mg MA/kg/day) relapsed. The antimony concentrations in macaque plasma and tissue samples were greater in the full-dose group than in that receiving a subtherapeutic MA regimen. Our data also suggest the presence of drug-induced hepatic pathology. PMID:19822700

  5. Influence of antimony on the mechanical properties and gas content of alloy AlSi6Cu4

    OpenAIRE

    D. Medlen; D. Bolibruchova

    2011-01-01

    Aluminium alloys based on Al-Si are used in automotive and aerospace industries. AlSi6Cu4 alloy is used the complicated castings, whichmust comply high strength requirements. Strength characteristics can also be affected by the modifiers: Na, Sr, Sb. In the li terature ismentioned, that AlSi6Cu4 modified by sodium and strontium has negative effect - increases of the gas absorption. Modification of AlSi6Cu4 alloy by antimony, is still not mentioned in the literature. The article gives the effe...

  6. The influence of remelting on the properties of AlSi6Cu4 alloy modified by antimony

    Directory of Open Access Journals (Sweden)

    D. Medlen

    2012-01-01

    Full Text Available The paper deals with the problem of multiple remelting influence on AlSi6Cu4 alloy modified by antimony on chosen mechanical characteristics, microstructure and gas content. This foundry alloy is used mostly in automotive industry. Foundry Aluminum-Silicon alloys are also used in number of industrial weight sensitive applications because of their low weight and very good castability and good mechanical properties. Modifiers are usually added to molten aluminum-silicon alloys to refine the eutectic phase particle shape and improve the mechanical properties of the final cast products and Al-Si alloys cast properties.

  7. Flow analysis-hydride generation-gas phase derivative molecular absorption spectrophotometric determination of antimony in antileishmanial drugs

    Directory of Open Access Journals (Sweden)

    Máximo Gallignani

    2009-01-01

    Full Text Available In the present work, the development of a method based on the coupling of flow analysis (FA, hydride generation (HG, and derivative molecular absorption spectrophotometry (D-EAM in gas phase (GP, is described in order to determine total antimony in antileishmanial products. Second derivative order (D²224nm of the absorption spectrum (190 - 300 nm is utilized as measurement criterion. Each one of the parameters involved in the development of the proposed method was examined and optimized. The utilization of the EAM in GP as detection system in a continuous mode instead of atomic absorption spectrometry represents the great potential of the analytic proposal.

  8. Effect of external energy on atomic, crystalline and powder characteristics of antimony and bismuth powders

    Indian Academy of Sciences (India)

    Vikram V Dabhade; Rama Mohan R Tallapragada; Mahendra Kumar Trivedi

    2009-10-01

    Next to atoms and molecules the powders are the smallest state of matter available in high purities and large quantities. The effect of any external energy on the shape, morphology and structure can thus be studied with relative ease. The present investigation deals with the effect of a non-contact external energy on the powders of antimony and bismuth. The characteristics of powders treated by external energy are compared with the as received powders (control). The average particle sizes, 50 and 99, the sizes below which 99% of the particles are present showed significant increase and decrease indicating that the energy had caused deformation and fracture as if the powders have been subjected to high energy milling. To be able to understand the reasons for these changes the powders are characterized by techniques such as X-ray diffraction (XRD), surface area determination (BET), thermal analytical techniques such as DTA–DTG, DSC–TGA and SDTA and scanning electron microscopy (SEM). The treated powder samples exhibited remarkable changes in the powder characteristics at all structural levels starting from polycrystalline particles, through single crystal to atoms. The external energy had changed the lattice parameters of the unit cell which in turn changed the crystallite size and density. The lattice parameters are then used to compute the weight and effective nuclear charge of the atom which showed significant variation. It is speculated that the external energy is acting on the nucleus through some reversible weak interaction of larger cross section causing changes in the proton to neutron ratios. Thus the effect is felt by all the atoms, and hence the unit cell, single crystal grain and grain boundaries. The stresses generated in turn may have caused deformation or fracture of the weak interfaces such as the crystallite and grain boundaries.

  9. Contamination of bottled waters with antimony leaching from polyethylene terephthalate (PET) increases upon storage.

    Science.gov (United States)

    Shotyk, William; Krachler, Michael

    2007-03-01

    Antimony concentrations were determined in 132 brands of bottled water from 28 countries. Two of the brands were at or above the maximum allowable Sb concentration for drinking water in Japan (2 microg/L). Elevated concentrations of Sb in bottled waters are due mainly to the Sb2O3 used as the catalyst in the manufacture of polyethylene terephthalate (PET(E)). The leaching of Sb from PET(E) bottles shows variable reactivity. In 14 brands of bottled water from Canada, Sb concentrations increased on average 19% during 6 months storage at room temperature, but 48 brands of water from 11 European countries increased on average 90% under identical conditions. A mineral water from France in PET(E), purchased in Germany, yielded 725 ng/L when first tested, but 1510 ng/L when it was stored for 6 months at room temperature; the same brand of water, purchased in Hong Kong, yielded 1990 ng/L Sb. Pristine groundwater containing 1.7+/-0.4 ng/L Sb (n = 6) yielded 26.6+/-2.3 ng/L Sb (n = 3) after storage in PET(E) bottles from Canada for 6 months versus 281+/-38 ng/L Sb (n = 3) in PET(E) bottles from Germany. Tap water bottled commercially in PET(E) in December 2005 contained 450+/-56 ng/L Sb (n = 3) versus 70.3+/-0.3 ng/L Sb (n = 3) when sampled from a household faucet in the same village (Bammental, Germany), and 25.7+/-1.5 ng/L Sb (n = 3) from a local artesian flow. PMID:17396641

  10. Uptake, translocation and transformation of antimony in rice (Oryza sativa L.) seedlings.

    Science.gov (United States)

    Cai, Fei; Ren, Jinghua; Tao, Shu; Wang, Xilong

    2016-02-01

    Antimony (Sb), as a toxic metalloid, has been gaining increasing research concerns due mainly to its severe pollution in many places. Rice has been identified to be the dominant intake route of Sb by residents close to the Sb mining areas. A hydroponic experiment was conducted to investigate the difference in uptake, translocation and transformation of Sb in rice seedlings of four cultivars exposed to 0.2 or 1.0 mg/L of Sb(V). The results showed that mass concentration of iron plaque (mg/kg FW) formed at the root surfaces of cultivar N was the highest among all tested cultivars at both low and high exposure levels of Sb(V). The accumulated Sb concentration in iron plaque significantly increased with an increase in mass concentration of iron plaque formed at the rice root. The total amount of iron plaque (mg/pot) at rice root generally increased with increasing exposed Sb(V) concentration, which was closely associated with the increasing lipid peroxidation in roots. Concentration percentage of Sb in rice root significantly reduced as the corresponding value in the iron plaque increased, suggesting that iron plaque formation strongly suppressed uptake of Sb by rice root. Sb concentration in rice tissues followed an order: root > stem, leaf. The japonica rice (cultivars N and Z) exhibited a stronger translocation tendency of Sb from root to stem than indica hybrid rice (cultivars F and G). Translocation of Sb from root of cultivar F to its stem and leaf was sharply enhanced with increasing Sb exposure concentration. Sb(V) could be reduced to Sb(III) in rice tissues, especially in stems (10-26% of the total Sb). For the sake of food safety, the difference in uptake, translocation and transformation of Sb in rice species planted in Sb-contaminated soils should be taken into consideration.

  11. Association of drinking-water source and use characteristics with urinary antimony concentrations.

    Science.gov (United States)

    Makris, Konstantinos C; Andra, Syam S; Herrick, Lisa; Christophi, Costas A; Snyder, Shane A; Hauser, Russ

    2013-03-01

    Environmental factors, such as storage time, frequency of bottle reuse and temperature, have been shown to facilitate antimony (Sb) leaching from water- and food-packaging materials. The globally escalating consumption of water packaged in Sb-containing bottles, such as that of polyethylene terephthalate (PET), could increase human daily Sb doses. This study set out to investigate the relationship between drinking-water source, use characteristics, and urinary Sb concentrations (U-Sb) accompanied with survey responses of a healthy (n=35) Cypriot participant pool. One spot urine sample was collected during administration of questionnaire, while a second spot urine sample was collected from the same individual about 7 days later. Urinary and water Sb concentrations were measured with an inductively coupled plasma mass spectrometer. Survey responses showed that bottled water summed over various volumes and plastic types, such as polycarbonate and PET contributed to an average 61% of daily water consumption. Water sources such as tap, mobile stations (explained in a following section), and well water contributed to 24%, 14%, and 2% of an individual's daily water consumption pattern, respectively. Average daily potable water use of both bottled and tap water by individuals consisted of 65% drinking-water, while the remaining 35% was water used for preparing cold and hot beverages, such as, tea, coffee, and juices. A significant (P=0.02) association between per capita water consumption from PET bottles and urinary creatinine-unadjusted concentrations was observed, but this relationship did not remain after inclusion of covariates in a multivariate regression model. In the creatinine-adjusted regression model, only gender (female) was a significant (P<0.01) predictor of U-Sb, after adjusting for several covariates. It is proposed that consumption data collection on various water uses and sources among individuals could perhaps decrease the uncertainty associated with

  12. Effects of Residual Elements Arsenic, Antimony, and Tin on Surface Hot Shortness

    Science.gov (United States)

    Yin, Lan; Sridhar, Seetharaman

    2011-10-01

    Scrap-based electric arc furnace (EAF) steelmaking is limited by a surface cracking problem in the recycled steel products, which is known as surface hot shortness. This problem originates from the excessive amount of copper (Cu) in the steel scrap, which enriches during the oxidation of iron (Fe) and consequently melts and penetrates into the austenite grain boundaries. In this article, the effects of arsenic (As), antimony (Sb), and tin (Sn) on surface hot shortness were investigated. A series of Fe-0.3 wt pct Cu- x wt pct (As, Sb, or Sn) alloys with x content ranging from 0.06 to 0.10 wt pct was oxidized in air at 1423 K (1150 °C) for 60, 300, and 600 seconds inside the chamber of a thermogravimety analyzer (TGA) where heat is supplied through infrared radiation. Scanning electron microscopy (SEM) investigations show that (1) the presence of Sb and Sn results in severe grain boundary cracking, whereas the presence of As does not, (2) open cracks with Fe oxides were found beneath the oxide/metal interface in the Sb and Sn alloys, and (3) the oxide/metal interfaces for all As, Sb, and Sn alloys are planar. Penetration experiments of pure Cu and Cu-30 wt pct Sn liquid were also conducted in the chamber of a hot-stage confocal laser scanning microscopy (CLSM) in nonoxidizing atmosphere: (1) on the Fe-35 wt pct manganese (Mn) alloys to study the correlation between cracking and grain boundary characters, and (2) on the pure Fe substrates to exclude the bulk segregation effects of Sn on grain boundary cracking. It was found that grain boundary cracking rarely took place on low-energy grain boundaries. The results also suggest that the bulk segregation of Sn in the substrate is not necessary to promote significant grain boundary cracking, and as long as the liquid phase contains Sn, it will be highly embrittling.

  13. Green and red fluorescence upconversion in neodymium-doped low phonon antimony glasses

    International Nuclear Information System (INIS)

    A new K2O-B2O3-Sb2O3 (KBS) glass system having low phonon energy (about 600 cm-1) doped with Nd3+ ions has been developed. Infrared reflection spectroscopic (IRRS) studies have been employed to establish its low phonon energy. Ultraviolet-visible-near infrared (UV-vis-NIR) absorption and photoluminescence upconversion properties with special emphasis on the spectrochemistry of the 15K2O-15B2O3-70Sb2O3 (mol%) glass have been studied doping with different concentrations (0.1-1.0 wt%) of Nd2O3. UV-vis-NIR absorption band positions have been justified with quantitative calculation of nephelauxetic parameter and covalent bonding characteristics of the host. NIR to visible upconversion has been investigated by exciting at 805 nm at room temperature. Two upconverted bands originating from the 4G7/2 → 4I9/2 and 4G7/2 → 4I13/2 transitions are found to be centered at 540 nm (green, medium) and 650 nm (red, strong), respectively. These bands have been explained from the evaluation of the absorption and excitation spectra. The upconversion processes have been explained by the excited state absorption (ESA), energy transfer (ET), cooperative energy transfer (CET) and cross-relaxation (CR) mechanisms involving population of the metastable (storage) energy level (4G7/2) by effects of multiphonon deexcitation and thermal population. It is evident from the IRRS study that the upconversion phenomena are expedited by the low multiphonon relaxation rate in antimony glasses owing to their low phonon energy (602 cm-1, the main and highest intensity Sb-O-Sb stretching band) which is very close to that of fluoride glasses (500-600 cm-1).

  14. EPR, optical absorption and luminescence studies of Cr3+-doped antimony phosphate glasses

    Science.gov (United States)

    De Vicente, F. S.; Santos, F. A.; Simões, B. S.; Dias, S. T.; Siu Li, M.

    2014-12-01

    Antimony phosphate glasses (SbPO) doped with 3 and 6 mol% of Cr3+ were studied by Electron Paramagnetic Resonance (EPR), UV-VIS optical absorption and luminescence spectroscopy. The EPR spectra of Cr3+-doped glasses showed two principal resonance signals with effective g values at g = 5.11 and g = 1.97. UV-VIS optical absorption spectra of SbPO:Cr3+ presented four characteristics bands at 457, 641, 675, and 705 nm related to the transitions from 4A2(F) to 4T1(F), 4T2(F), 2T1(G), and 2E(G), respectively, of Cr3+ ions in octahedral symmetry. Optical absorption spectra of SbPO:Cr3+ allowed evaluating the crystalline field Dq, Racah parameters (B and C) and Dq/B. The calculated value of Dq/B = 2.48 indicates that Cr3+ ions in SbPO glasses are in strong ligand field sites. The optical band gap for SbPO and SbPO:Cr3+ were evaluated from the UV optical absorption edges. Luminescence measurements of pure and Cr3+-doped glasses excited with 350 nm revealed weak emission bands from 400 to 600 nm due to the 3P1 → 1S0 electronic transition from Sb3+ ions. Cr3+-doped glasses excited with 415 nm presented Cr3+ characteristic luminescence spectra composed by two broad bands, one band centered at 645 nm (2E → 4A2) and another intense band from 700 to 850 nm (4T2 → 4A2).

  15. Metagenomic approach reveals variation of microbes with arsenic and antimony metabolism genes from highly contaminated soil.

    Directory of Open Access Journals (Sweden)

    Jinming Luo

    Full Text Available Microbes have great potential for arsenic (As and antimony (Sb bioremediation in heavily contaminated soil because they have the ability to biotransform As and Sb to species that have less toxicity or are more easily removed. In this study, we integrated a metagenomic method with physicochemical characterization to elucidate the composition of microbial community and functional genes (related to As and Sb in a high As (range from 34.11 to 821.23 mg kg-1 and Sb (range from 226.67 to 3923.07 mg kg-1 contaminated mine field. Metagenomic analysis revealed that microbes from 18 phyla were present in the 5 samples of soil contaminated with high As and Sb. Moreover, redundancy analysis (RDA of the relationship between the 18 phyla and the concentration of As and Sb demonstrated that 5 phyla of microbes, i.e. Actinobacteria, Firmicutes, Nitrospirae, Tenericutes and Gemmatimonadetes were positively correlated with As and Sb concentration. The distribution, diversity and abundance of functional genes (including arsC, arrA, aioA, arsB and ACR3 were much higher for the samples containing higher As and Sb concentrations. Based on correlation analysis, the results showed a positive relationship between arsC-like (R2 = 0.871 and aioA-like (R2 = 0.675 gene abundance and As concentration, and indicated that intracellular As(V reduction and As(III oxidation could be the dominant As detoxification mechanism enabling the microbes to survive in the environment. This study provides a direct and reliable reference on the diversity of microbial community and functional genes in an extremely high concentration As- and Sb-contaminated environment.

  16. Simultaneous determination of antimony and boron in beverage and dairy products by flame atomic absorption spectrometry after separation and pre-concentration by cloud-point extraction.

    Science.gov (United States)

    Altunay, Nail; Gürkan, Ramazan

    2016-01-01

    A new cloud-point extraction (CPE) method was developed for the pre-concentration and simultaneous determination of Sb(III) and B(III) by flame atomic absorption spectrometry (FAAS). The method was based on complexation of Sb(III) and B(III) with azomethine-H in the presence of cetylpyridinium chloride (CPC) as a signal-enhancing agent, and then extraction into the micellar phase of Triton X-114. Under optimised conditions, linear calibration was obtained for Sb(III) and B(III) in the concentration ranges of 0.5-180 and 2.5-600 μg l(-1) with LODs of 0.15 and 0.75 μg l(-1), respectively. Relative standard deviations (RSDs) (25 and 100 μg l(-1) of Sb(III) and B(III), n = 6) were in a range of 2.1-3.8% and 1.9-2.3%, respectively. Recoveries of spiked samples of Sb(III) and B(III) were in the range of 98-103% and 99-102%, respectively. Measured values for Sb and B in three standard reference materials were within the 95% confidence limit of the certified values. Also, the method was used for the speciation of inorganic antimony. Sb(III), Sb(V) and total Sb were measured in the presence of excess boron before and after pre-reduction with an acidic mixture of KI-ascorbic acid. The method was successfully applied to the simultaneous determination of total Sb and B in selected beverage and dairy products.

  17. 流动注射在线离子交换分离富集-氢化物发生原子荧光光谱法测定铜合金中痕量锑%Determination of trace antimony in copper alloys by flow injection on-line ion-exchange separation and enrichment-hydride generation atomic fluorescence spectrometry

    Institute of Scientific and Technical Information of China (English)

    吴良俊; 邱海鸥; 郝志红; 袁红战; 郑洪涛

    2009-01-01

    A method for the determination of trace antimony in copper by flow injection on-line ion-exchange separation and enrichment-hydride generation atomic fluorescence spectrometry is suggested. The manifolds and operating program for ftlow injection on-line ion-exchange were designed and chemical conditions were optimized. Antimony complex was absorbed on strongly basic anion exchange resin 717 with 1. 4 mol/L HC1 as absorbent medium and 2. 0 mol/L HNO_3 for elution. The interference of co-existent elements (i-ron, nickel, lead, etc) was eliminated while antimony was enriched and was determined by hydride generation-atomic fluorescence spectrometry. The method is easy to operate and fast, and has lesser pollution to environment. The linear range is 0. 2-120μg/L and the RSD is 3%~5% with detection limit of 0. 05 μg/L. The results for determination of antimony in standard samples of copper alloys are satisfactory.%提出了流动注射离子交换在线分离富集-氢化物发生原子荧光光谱法测定铜合金中痕量锑的分析方法.设计了流动注射在线离子交换的流路和操作程序,优化了各项化学条件.采用717强碱性阴离子交换树脂吸附锑,并能有效消除铁、镍、铅等元素的干扰,也使大量基体元素铜与待测元素分离,锑在1.4 mol/L的HCl介质中上柱,选用2.0 mol/L的HNO_3作为洗脱剂.实现了氢化物发生原子荧光光谱法对铜合金中痕量锑的在线测定.方法操作简便、快速,环境污染小,线性范围为0.15~120 μg/L,相对标准偏差在3%~5%之间,检出限为0.05μg/L.方法应用于铜合金标准样品,结果与推荐值吻合.

  18. Nutritional status in patients with cutaneous leishmaniasis and a study of the effects of zinc supplementation together with antimony treatment

    Directory of Open Access Journals (Sweden)

    Miguel Guzman-Rivero

    2014-11-01

    Full Text Available Background: The role of micronutrient status for the incidence and clinical course of cutaneous leishmaniasis is not much studied. Still zinc supplementation in leishmaniasis has shown some effect on the clinical recovery, but the evidence in humans is limited. Objective: To compare biochemical nutritional status in cutaneous leishmaniasis patients with that in controls and to study the effects of zinc supplementation for 60 days. Design: Twenty-nine patients with cutaneous leishmaniasis were treated with antimony for 20 days. Fourteen of them got 45 mg zinc daily and 15 of them got placebo. Biomarkers of nutritional and inflammatory status and changes in size and characteristics of skin lesions were measured. Results: The level of transferrin receptor was higher in patients than in controls but otherwise no differences in nutritional status were found between patients and controls. No significant effects of zinc supplementation on the clinical recovery were observed as assessed by lesion area reduction and characteristics or on biochemical parameters. Conclusions: It is concluded that nutritional status was essentially unaffected in cutaneous leishmaniasis and that oral zinc supplementation administered together with intramuscular injection of antimony had no additional clinical benefit.

  19. Detection of pathogenic bacteria in skin lesions of patients with chiclero's ulcer: reluctant response to antimonial treatment

    Directory of Open Access Journals (Sweden)

    Isaac-Márquez Angélica Patricia

    2003-01-01

    Full Text Available We investigated the bacterial flora present in skin lesions of patients with chiclero's ulcer from the Yucatan peninsula of Mexico using conventional culture methods (11 patients, and an immunocolorimetric detection of pathogenic Streptococcus pyogenes (15 patients. Prevalence of bacteria isolated by culture methods was 90.9% (10/11. We cultured, from chiclero's ulcers (60%, pathogenic bacterial such as Staphylococcus aureus (20%, S. pyogenes (1.6%, Pseudomonas aeruginosa (1.6%, Morganella morganii (1.6%, and opportunist pathogenic bacteria such as Klebsiella spp. (20.0%, Enterobacter spp. (20%, and Enterococcus spp. (20%. We also cultured coagulase-negative staphylococci in 40% (4/10 of the remaining patients. Micrococcus spp. and coagulase-negative staphylococci constituted the bacterial genuses more frequently isolated in the normal skin of patients with chiclero's ulcer and healthy individuals used as controls. We also undertook another study to find out the presence of S. pyogenes by an immunocolorimetric assay. This study indicated that 60% (9/15 of the ulcerated lesions, but not normal controls, were contaminated with S. pyogenes. Importantly, individuals with purulent secretion and holding concomitant infections with S. pyogenes, S. aureus, P. aeruginosa, M. morganii, and E. durans took longer to heal Leishmania (L. mexicana infections treated with antimonial drugs. Our results suggest the need to eliminate bacterial purulent infections, by antibiotic treatment, before starting antimonial administration to patients with chiclero's ulcer.

  20. Complement activation-related pseudoallergy in dogs following intravenous administration of a liposomal formulation of meglumine antimoniate

    Directory of Open Access Journals (Sweden)

    Raul R. Ribeiro

    2013-08-01

    Full Text Available The increasing use of nanotechnologies in advanced therapies has allowed the observation of specific adverse reactions related to nanostructures. The toxicity of a novel liposome formulation of meglumine antimoniate in dogs with visceral leishmaniasis after single dose has been investigated. Groups of 12 animals received by the intravenous route a single dose of liposomal meglumine antimoniate (group I [GI], 6.5 mg Sb/kg, empty liposomes (GII or isotonic saline (GIII. Evaluation of hematological and biochemical parameters showed no significant changes 4 days after administration. No undesired effects were registered in the GIII. However, adverse reactions were observed in 67.7% of dogs from both groups that received liposomal formulations. The side effects began moments after bolus administration and disappeared during the first 15 minutes after treatment. Prostation, sialorrhea and defecation were the most frequent clinical signs, registered in 33.3% and 41.6 % of animals from the groups GI and GII, respectively. Tachypnea, mydriasis, miosis, vomiting and cyanosis were also registered in both groups. The adverse reactions observed in this study were attributed to the activation of the complement system by lipid vesicles in a phenomenon known as Complement Activation-Related Pseudoallergy (CARPA. The influence of the physical-chemical characteristics of liposomal formulation in the triggering of CARPA is discussed.

  1. Determination of Antimony (III in Real Samples by Anodic Stripping Voltammetry Using a Mercury Film Screen-Printed Electrode

    Directory of Open Access Journals (Sweden)

    Olga Domínguez-Renedo

    2009-01-01

    Full Text Available This paper describes a procedure for the determination of antimony (III by differential pulse anodic stripping voltammetry using a mercury film screen-printed electrode as the working electrode. The procedure has been optimized using experimental design methodology. Under these conditions, in terms of Residual Standard Deviation (RSD, the repeatability (3.81 % and the reproducibility (5.07 % of the constructed electrodes were both analyzed. The detection limit for Sb (III was calculated at a value of 1.27×10–8 M. The linear range obtained was between 0.99 × 10–8 – 8.26 × 10–8 M. An analysis of possible effects due to the presence of foreign ions in the solution was performed and the procedure was successfully applied to the determination of antimony levels in pharmaceutical preparations and sea water samples.

  2. Antimony doped tin oxides and their composites with tin pyrophosphates as catalyst supports for oxygen evolution reaction in proton exchange membrane water electrolysis

    DEFF Research Database (Denmark)

    Xu, Junyuan; Li, Qingfeng; Hansen, Martin Kalmar;

    2012-01-01

    Proton exchange membrane water electrolysers operating at typically 80 °C or at further elevated temperatures suffer from insufficient catalyst activity and durability. In this work, antimony doped tin oxide nanoparticles were synthesized and further doped with an inorganic proton conducting phase...

  3. Real-world emission factors for antimony and other brake wear related trace elements: size-segregated values for light and heavy duty vehicles.

    Science.gov (United States)

    Bukowiecki, Nicolas; Lienemann, Peter; Hill, Matthias; Figi, Renato; Richard, Agnes; Furger, Markus; Rickers, Karen; Falkenberg, Gerald; Zhao, Yongjing; Cliff, Steven S; Prevot, Andre S H; Baltensperger, Urs; Buchmann, Brigitte; Gehrig, Robert

    2009-11-01

    Hourly trace element measurements were performed in an urban street canyon and next to an interurban freeway in Switzerland during more than one month each, deploying a rotating drum impactor (RDI) and subsequent sample analysis by synchrotron radiation X-ray fluorescence spectrometry (SR-XRF). Antimony and other brake wear associated elements were detected in three particle size ranges (2.5-10, 1-2.5, and 0.1-1 microm). The hourly measurements revealed that the effect of resuspended road dust has to be taken into account for the calculation of vehicle emission factors. Individual values for light and heavy duty vehicles were obtained for stop-and-go traffic in the urban street canyon. Mass based brake wear emissions were predominantly found in the coarse particle fraction. For antimony, determined emission factors were 11 +/- 7 and 86 +/- 42 microg km(-1) vehicle(-1) for light and heavy duty vehicles, respectively. Antimony emissions along the interurban freeway with free-flowing traffic were significantly lower. Relative patterns for brake wear related elements were very similar for both considered locations. Beside vehicle type specific brake wear emissions, road dust resuspension was found to be a dominant contributor of antimony in the street canyon. PMID:19924925

  4. Correlation models between environmental factors and bacterial resistance to antimony and copper.

    Directory of Open Access Journals (Sweden)

    Zunji Shi

    Full Text Available Antimony (Sb and copper (Cu are toxic heavy metals that are associated with a wide variety of minerals. Sb(III-oxidizing bacteria that convert the toxic Sb(III to the less toxic Sb(V are potentially useful for environmental Sb bioremediation. A total of 125 culturable Sb(III/Cu(II-resistant bacteria from 11 different types of mining soils were isolated. Four strains identified as Arthrobacter, Acinetobacter and Janibacter exhibited notably high minimum inhibitory concentrations (MICs for Sb(III (>10 mM,making them the most highly Sb(III-resistant bacteria to date. Thirty-six strains were able to oxidize Sb(III, including Pseudomonas-, Comamonas-, Acinetobacter-, Sphingopyxis-, Paracoccus- Aminobacter-, Arthrobacter-, Bacillus-, Janibacter- and Variovorax-like isolates. Canonical correspondence analysis (CCA revealed that the soil concentrations of Sb and Cu were the most obvious environmental factors affecting the culturable bacterial population structures. Stepwise linear regression was used to create two predictive models for the correlation between soil characteristics and the bacterial Sb(III or Cu(II resistance. The concentrations of Sb and Cu in the soil was the significant factors affecting the bacterial Sb(III resistance, whereas the concentrations of S and P in the soil greatly affected the bacterial Cu(II resistance. The two stepwise linear regression models that we derived are as follows: MIC(Sb(III=606.605+0.14533 x C(Sb+0.4128 x C(Cu and MIC((Cu(II=58.3844+0.02119 x C(S+0.00199 x CP [where the MIC(Sb(III and MIC(Cu(II represent the average bacterial MIC for the metal of each soil (μM, and the C(Sb, C(Cu, C(S and C(P represent concentrations for Sb, Cu, S and P (mg/kg in soil, respectively, p<0.01]. The stepwise linear regression models we developed suggest that metals as well as other soil physicochemical parameters can contribute to bacterial resistance to metals.

  5. Green and red fluorescence upconversion in neodymium-doped low phonon antimony glasses

    Energy Technology Data Exchange (ETDEWEB)

    Som, Tirtha [Glass Technology Laboratory, Central Glass and Ceramic Research Institute (Council of Scientific and Industrial Research), 196 Raja S.C. Mullick Road, Kolkata 700032 (India); Karmakar, Basudeb [Glass Technology Laboratory, Central Glass and Ceramic Research Institute (Council of Scientific and Industrial Research), 196 Raja S.C. Mullick Road, Kolkata 700032 (India)], E-mail: basudebk@cgcri.res.in

    2009-05-12

    A new K{sub 2}O-B{sub 2}O{sub 3}-Sb{sub 2}O{sub 3} (KBS) glass system having low phonon energy (about 600 cm{sup -1}) doped with Nd{sup 3+} ions has been developed. Infrared reflection spectroscopic (IRRS) studies have been employed to establish its low phonon energy. Ultraviolet-visible-near infrared (UV-vis-NIR) absorption and photoluminescence upconversion properties with special emphasis on the spectrochemistry of the 15K{sub 2}O-15B{sub 2}O{sub 3}-70Sb{sub 2}O{sub 3} (mol%) glass have been studied doping with different concentrations (0.1-1.0 wt%) of Nd{sub 2}O{sub 3}. UV-vis-NIR absorption band positions have been justified with quantitative calculation of nephelauxetic parameter and covalent bonding characteristics of the host. NIR to visible upconversion has been investigated by exciting at 805 nm at room temperature. Two upconverted bands originating from the {sup 4}G{sub 7/2} {yields} {sup 4}I{sub 9/2} and {sup 4}G{sub 7/2} {yields} {sup 4}I{sub 13/2} transitions are found to be centered at 540 nm (green, medium) and 650 nm (red, strong), respectively. These bands have been explained from the evaluation of the absorption and excitation spectra. The upconversion processes have been explained by the excited state absorption (ESA), energy transfer (ET), cooperative energy transfer (CET) and cross-relaxation (CR) mechanisms involving population of the metastable (storage) energy level ({sup 4}G{sub 7/2}) by effects of multiphonon deexcitation and thermal population. It is evident from the IRRS study that the upconversion phenomena are expedited by the low multiphonon relaxation rate in antimony glasses owing to their low phonon energy (602 cm{sup -1}, the main and highest intensity Sb-O-Sb stretching band) which is very close to that of fluoride glasses (500-600 cm{sup -1})

  6. Novel organo-colloidal synthesis, optical properties, and structural analysis of antimony sesquioxide nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Validzic, Ivana Lj., E-mail: validzic@vinca.rs; Abazovic, Nadica D.; Mitric, Miodrag [University of Belgrade, ' Vinca' Institute of Nuclear Sciences (Serbia); Lalic, Milan V. [Universidade Federal de Sergipe, Departamento de Fisica (Brazil); Popovic, Zoran S. [University of Belgrade, ' Vinca' Institute of Nuclear Sciences (Serbia); Vukajlovic, Filip R. [' Vinca' Institute of Nuclear Sciences (Serbia)

    2013-01-15

    We report the novel colloidal syntheses in organic media of antimony sesquioxide ( Sb{sub 2}O{sub 3} ) spherical nanoparticles (30-250 nm) and octahedron micro- and nanocrystals (100nm - 4{mu}) depending on the synthetic method conditions. It is observed that small differences in the synthetic procedure cause large differences in the very changeable morphology. The structure of Sb{sub 2}O{sub 3} powders was refined down to the R-factors of 9.57, 7.44, 9.19, 9.78, and 8.30 %. The refinement showed that Sb{sub 2}O{sub 3} powder belongs to the cubic crystal type with space group Fd 3-bar m (No. 227). The values of estimated standard deviations, as well as reliability factors, confirmed that the structure of Sb{sub 2}O{sub 3} was well refined. Ultraviolet and visible (UV-Vis) absorption spectroscopy and diffuse reflectance measurements (DRS) reveal that the optical band gap energies found for the Sb{sub 2}O{sub 3} octahedrons and nanoparticles, micro- and nanocrystals, respectively, are quite independent of the synthetic method conditions and synthesized morphology and is found to be between 4.1-4.4 eV. No peaks in both photoluminescence (PL) emission and excitation spectra have been observed for a broad spectral range, typical for this material. In order to discriminate between conflicting experimental results concerning the band gap energy of this compound, we investigated theoretically the electronic structure and optical properties of one of the cubic sesquioxide Sb{sub 2}O{sub 3} samples synthesized here. This has been done on the basis of density functional theory (DFT) with the generalized gradient approximation (GGA) and improved version of exchange potential suggested recently by Tran and Blaha (TB-mBJ). The main characteristic of the calculated TB-mBJ electronic structure is the significant improvement of the band gap value, which is in perfect agreement with our experimental measurements. The real and imaginary parts of the dielectric tensor are also

  7. The presence and leachability of antimony in different wastes and waste handling facilities in Norway.

    Science.gov (United States)

    Okkenhaug, G; Almås, Å R; Morin, N; Hale, S E; Arp, H P H

    2015-11-01

    The environmental behaviour of antimony (Sb) is gathering attention due to its increasingly extensive use in various products, particularly in plastics. Because of this it may be expected that plastic waste is an emission source for Sb in the environment. This study presents a comprehensive field investigation of Sb concentrations in diverse types of waste from waste handling facilities in Norway. The wastes included waste electrical and electronic equipment (WEEE), glass, vehicle fluff, combustibles, bottom ash, fly ash and digested sludge. The highest solid Sb concentrations were found in WEEE and vehicle plastic (from 1238 to 1715 mg kg(-1)) and vehicle fluff (from 34 to 4565 mg kg(-1)). The type of acid used to digest the diverse solid waste materials was also tested. It was found that HNO3:HCl extraction gave substantially lower, non-quantitative yields compared to HNO3:HF. The highest water-leachable concentration for wastes when mixed with water at a 1 : 10 ratio were observed for plastic (from 0.6 to 2.0 mg kg(-1)) and bottom ash (from 0.4 to 0.8 mg kg(-1)). For all of the considered waste fractions, Sb(v) was the dominant species in the leachates, even though Sb(iii) as Sb2O3 is mainly used in plastics and other products, indicating rapid oxidation in water. This study also presents for the first time a comparison of Sb concentrations in leachate at waste handling facilities using both active grab samples and DGT passive samples. Grab samples target the total suspended Sb, whereas DGT targets the sum of free- and other chemically labile species. The grab sample concentrations (from 0.5 to 50 μg L(-1)) were lower than the predicted no-effect concentration (PNEC) of 113 μg L(-1). The DGT concentrations were substantially lower (from 0.05 to 9.93 μg L(-1)) than the grab samples, indicating much of the Sb is present in a non-available colloidal form. In addition, air samples were taken from the chimney and areas within combustible waste incinerators, as

  8. Growth, photosynthesis, and defense mechanism of antimony (Sb)-contaminated Boehmeria nivea L.

    Science.gov (United States)

    Chai, Li-Yuan; Mubarak, Hussani; Yang, Zhi-Hui; Yong, Wang; Tang, Chong-Jian; Mirza, Nosheen

    2016-04-01

    Ramie (Boehmeria nivea L.) is the oldest cash fiber crop in China and is widely grown in antimony (Sb) mining areas. To evaluate the extent of Sb resistance and tolerance, the growth, tolerance index (TI), Sb content in plant parts and in Hoagland solution, bioaccumulation factor (BF), photosynthesis, and physiological changes in Sb-contaminated B. nivea (20, 40, 80, and 200 mg L(-1) Sb) grown hydroponically were investigated. The Sb tolerance and resistance of ramie were clearly revealed by growth inhibition, a TI between 13 and 99 %, non-significant changes in the maximum quantum efficiency of photosystem (F v /F m ), energy-harvesting efficiency (photosystem II (PSII)) and single-photon avalanche diode (SPAD) value, a significant increase in Sb in plant parts, BF >1, and an increase in catalase (CAT) and malondialdehyde (MDA) at 200 mg L(-1) Sb. Under increasing Sb stress, nearly the same non-significant decline in the maximum quantum efficiency of photosystem (F v /F m ), energy-harvesting efficiency (PSII), relative quantum yield of photosystem II (φPSII), and photochemical quenching (qP), except for F v /F m at 20 mg L(-1) Sb, were recorded. SPAD values for chlorophyll under Sb stress showed an increasing trend, except for a slight decrease, i.e., continuous increase in MDA, superoxide dismutase (SOD), peroxidase (POD), and CAT activities were suppressed under Sb addition up to 40 mg L(-1) Sb and the addition of Sb enhanced enzyme production at 80 and 200 mg L(-1) Sb. A continuous decrease in SOD, POD, and CAT up to 40 mg L(-1) Sb and enhancements at ≥80 mg L(-1), along with the continuous enhancement of MDA activity and inhibited biomass production, clearly reveal the roles of these enzymes in detoxifying Sb stress and the defense mechanism of ramie at 80 mg L(-1) Sb. Thus, B. nivea constitutes a promising candidate for Sb phytoremediation at mining sites. PMID:26711292

  9. Synthesis and Properties of Light-tolerant Organic Antimony%耐光型有机锑的合成及其性能研究

    Institute of Scientific and Technical Information of China (English)

    高勇; 韩永和; 李建丰; 袁余斌; 王爱红

    2014-01-01

    硫醇锑稳定剂由于其耐紫外光性能很差,在存储、运输和使用方面受到很大的限制。为解决这一问题,试探性以三氯化锑和巯基酯为原料,引入抗紫外线活性基团TBP-1(2,4-二羟基二苯甲酮),合成了“晒不黑”的有机锑热稳定剂。用红外光谱对产品结构进行了确认,光敏性实验表明其7周内不变色;静态热稳定性实验结果表明其与硫醇锑热稳定剂相当。%Because of its poor ultraviolet resistance , the storage , transportation and use of antimony mercaptide stabilizer was greatly limited.In order to solve this problem , a kind of synthesized organic antimony thermal stabilizer was prepared, which was light -tolerant with antimony trichloride , isooctyl thioglycollat as raw materials and TBP -1(2,4-dihydroxybenzophenone ) , with an anti-ultraviolet agent added in.The light-tolerant performance and thermal stability of product tested showed that the color of organic antimony as -synthesized was unchangeable when under the impact of direct sunlight for 7 weeks by infrared spectroscopy spectrum that was confirmed for structure of product , and the static experimental results showed that the thermal stability was nearly equivalent to antimony mercaptide.

  10. Research advances in microbial mechanism of antimony%微生物对锑的代谢机制研究进展

    Institute of Scientific and Technical Information of China (English)

    李明顺; 李洁; 王革娇

    2013-01-01

    锑(Sb)是一种自然界普遍存在的剧毒重金属,随着工业生产的日趋发展,我国部分地区土壤、水体及农产品受到严重的锑污染.作为环境污染物,锑中毒会导致人类心肌衰竭,肝坏死等疾病.自然界中的某些生物,特别是微生物却可以在极高锑浓度下生长,甚至可以利用这种元素作为能源物质,因此,微生物在锑的地球物质循环中起着重要的作用.研究生物对锑的代谢机制,对于保护环境与人体健康具有重要的现实意义.本文对锑在环境中的分布、污染状况、微生物对锑的代谢以及生物修复等方面的研究现状进行了综述.同时建议今后应加强以下三方面的研究:(1)筛选更多抗锑微生物或氧化锑的微生物;(2)发掘更多锑抗性基因或氧化基因;(3)开发锑污染土壤及水体的微生物修复技术.%Antimony (Sb) is a highly toxic heavy metal which widespreadly exists in nature.With the increasing development of industry,the soil,water and agricultural products are severely polluted by antimony in some regions of our country.As an environmental pollutant,antimony poisoning can lead to heart failure,human diseases such as liver necrosis.Some organisms in nature,especially the microorganisms can grow in the high concentration of antimony,and can even use the element as an energy material,so the microorganisms play an important role in the cycle of earth's materials.Study on metabolic mechanism of antimony has important practical significance to protect environment and human health.This study reviewed the researches of Sb distribution in the environment,the pollution status,microbial metabolism of antimony and bioremediation.At the same time it suggests that future researches should strengthen the following three aspects:(1) isolating more antimony resistance or antimony oxidizing microorganisms; (2) identifying more antimony resistant or oxidizing genes; (3) exploring microbial techniques to remediate

  11. Synthesis and characterization of nanostructured Mn(II) doped antimony-tin oxide (ATO) films on glass

    International Nuclear Information System (INIS)

    Sol–gel Mn(II) doped antimony tin oxide films were developed with precursor of atomic ratio range, Sn:Sb:Mn = 68–72:23–25:9–3. The X-ray diffraction patterns depict tetragonal cassiterite phase of SnO2. Transmission electron microscopy images suggest the nanostructured form of the doped materials. The increase in crystallite size with Mn(II) concentration is reflected by the larger band gap values (4.61–4.73 eV) arising from the excitonic transitions which also respond to PL emissions. Hall effect measurements show that the carrier concentration increases but mobility decreases for Mn(II) doping. Room temperature ferromagnetism with different saturation magnetic moments (Ms) has been observed for all dopant concentrations, 3–9 at%.

  12. The chemistry and behaviour of antimony in the soil environment with comparisons to arsenic: A critical review

    Energy Technology Data Exchange (ETDEWEB)

    Wilson, Susan C., E-mail: swilso24@une.edu.a [School of Environmental and Rural Science, University of New England, Armidale, NSW 2351 (Australia); Lockwood, Peter V., E-mail: peter.lockwood@une.edu.a [School of Environmental and Rural Science, University of New England, Armidale, NSW 2351 (Australia); Ashley, Paul M., E-mail: pashley@une.edu.a [School of Environmental and Rural Science, University of New England, Armidale, NSW 2351 (Australia); Tighe, Matthew, E-mail: mtighe2@une.edu.a [School of Environmental and Rural Science, University of New England, Armidale, NSW 2351 (Australia)

    2010-05-15

    This article provides a critical review of the environmental chemistry of inorganic antimony (Sb) in soils, comparing and contrasting findings with those of arsenic (As). Characteristics of the Sb soil system are reviewed, with an emphasis on speciation, sorption and phase associations, identifying differences between Sb and As behaviour. Knowledge gaps in environmentally relevant Sb data for soils are identified and discussed in terms of the limitations this imposes on understanding the fate, behaviour and risks associated with Sb in environmental soil systems, with particular reference to mobility and bioavailability. - A critical and comparative review of Sb and As chemistry and associations in soil systems identifies research directions needed for better understanding of risks.

  13. Antimony (SbIII) reduces growth, declines photosynthesis, and modifies leaf tissue anatomy in sunflower (Helianthus annuus L.).

    Science.gov (United States)

    Vaculík, Marek; Mrázová, Anna; Lux, Alexander

    2015-12-01

    The role of antimony (Sb)--a non-essential trace metalloid--in physiological processes running in crops is still poorly understood. Present paper describes the effect of Sb tartrate (SbIII) on growth, Sb uptake, photosynthesis, photosynthetic pigments, and leaf tissue organization in young sunflower plants grown in hydroponics. We found that growth of below- and aboveground part was reduced with increasing concentration of Sb in the medium. Although Sb was mostly taken up by sunflower roots and only small part (1-2%) was translocated to the shoots, decline in photosynthesis, transpiration, and decreased content of photosynthetic pigments were observed. This indicates that despite relatively low mobility of Sb in root-shoot system, Sb in shoot noticeably modifies physiological status and reduced plant growth. Additionally, leaf anatomical changes indicated that Sb reduced the size of intercellular spaces and made leaf tissue more compact. PMID:26194244

  14. Conjugative plasmid in Corynebacterium flaccumfaciens subsp. oortii that confers resistance to arsenite, arsenate, and antimony(III)

    Energy Technology Data Exchange (ETDEWEB)

    Hendrick, C.A.; Haskins, W.P.; Vidaver, A.K.

    1984-07-01

    Gene transfer systems for phytopathogenic corynebacteria have not been reported previously. In this paper a conjugative 46-megadalton plasmid (pDG101) found in Corynebacterium flaccumfaciens subsp. oorii CO101 is described that mediates resistance to arsenite, arsenate, and antimony(III). Transfer of the plasmid from CO101 to four other strains from the C. flaccumfaciens group occurred between cells immobilized on nitrocellulose filters or on agar surfaces. Transconjugant strains expressed the same levels of metal resistance as the donor strain and were able to act as donor strains in subsequent matings. The physical presence of the plasmid was detected by agarose gel electrophoresis. Arsenite-sensitive derivatives of the donor and transconjugant strains were obtained after heat treatment; these were cured of pDG101.

  15. Construction of spongy antimony-doped tin oxide/graphene nanocomposites using commercially available products and its excellent electrochemical performance

    Science.gov (United States)

    Zhao, Xiaowei; Zhang, Jingwei; Zhang, Jiwei; Gong, Chunhong; Gu, Xiufang; Ma, Zhihua; Zhou, Jingfang; Yu, Laigui; Zhang, Zhijun

    2015-10-01

    We construct successfully a porous antimony-doped tin oxide (ATO)/nitrogen-doped graphene 3-dimensional (3D) frameworks (denoted as ATO/NG/TEPA; TEPA refers to tetraethylenepentamine) by a one-pot hydrothermal process, with which TEPA aqueous solution is adopted to easily re-disperse commercial ATO precursor forming a transparent hydrosol. The results show that TEPA plays a key role in the construction of ATO/NG/TEPA, not only acting as a peptization reagent to re-disperse ATO precursor nanoparticles, and as a linker to combine ATO with graphene sheets. The as-fabricated ATO/NG/TEPA hybrid as the negative electrode of lithium ion batteries exhibits excellent lithium storage capacity and cycling stability. With the advantage of easily re-dispersing commercial ATO, the present synthetic route may be put into use for the large-scale production of the titled nanocomposites as the anode material of lithium ion batteries.

  16. Fabrication of superhydrophobic and heat-insulating antimony doped tin oxide/polyurethane films by cast replica micromolding.

    Science.gov (United States)

    Feng, Jie; Huang, Baoyuan; Zhong, Mingqiang

    2009-08-01

    A novel process for fabricating superhydrophobic and heat-insulating polymeric nanocomposite films was developed. Briefly, antimony doped tin oxide (ATO) nanoparticles that commonly endow coats heat-insulating and transparent functions were mixed into commercial waterborne polyurethane (WPU) suspensions to obtain ATO/WPU suspensions, which were then cast onto poly(dimethylsiloxane) (PDMS) stamps replicated from fresh lotus leaves. After being dried and peeled off from stamps, ATO/PU films with superhydrophobic surface and heat-insulating property were created, while PU films without ATO only showed high hydrophobicity. Scanning electron microscopy (SEM) imaging showed the surface of ATO/PU superhydrophobic films had unique micro- and nano-structures similar with those on the lotus leaf. On the contrary, no obvious nano-structures were found on the surface of pure PU films, demonstrating mixing functional nanoparticles into polymers is a necessary and feasible step in creating superhydrophobic and functional films by replica molding method. PMID:19394955

  17. lVIICROSTRUCTURE AND EUTECTIC MORPHOLOGY OF AL-12.5°/o Si ALLOY REFINED WITH ANTIMONY

    Directory of Open Access Journals (Sweden)

    Funda Kahraman

    2007-01-01

    Full Text Available Modification of Al-Si cast alloys can be achieved in two different ways, namely by additions of certain eleınents orwith rapid cooling rate. Modifications of the Al-Si al1oys are carried out extensivcly in industry to improve themechanical properties, particularly ductility. In this study, the effects of antiınony addition.s and growth rate on theınicrostructure and eutectic morphology on the directionally solidified Al- 1 2.5°/o Si cutectic all oy has beeninvestigated. The results showed that antimony can be identified as a grain refıner. Over modification occurs in Al-12.5 °/oSi alloy when modifier is present in the amount of 1 %Sb results in AISb compound.

  18. Antimony (SbIII) reduces growth, declines photosynthesis, and modifies leaf tissue anatomy in sunflower (Helianthus annuus L.).

    Science.gov (United States)

    Vaculík, Marek; Mrázová, Anna; Lux, Alexander

    2015-12-01

    The role of antimony (Sb)--a non-essential trace metalloid--in physiological processes running in crops is still poorly understood. Present paper describes the effect of Sb tartrate (SbIII) on growth, Sb uptake, photosynthesis, photosynthetic pigments, and leaf tissue organization in young sunflower plants grown in hydroponics. We found that growth of below- and aboveground part was reduced with increasing concentration of Sb in the medium. Although Sb was mostly taken up by sunflower roots and only small part (1-2%) was translocated to the shoots, decline in photosynthesis, transpiration, and decreased content of photosynthetic pigments were observed. This indicates that despite relatively low mobility of Sb in root-shoot system, Sb in shoot noticeably modifies physiological status and reduced plant growth. Additionally, leaf anatomical changes indicated that Sb reduced the size of intercellular spaces and made leaf tissue more compact.

  19. Super-resolution readout property of bismuth-doped antimony-based thin film as a functional mask for read-only memory

    Science.gov (United States)

    Lu, Xinmiao; Wu, Yiqun; Wang, Yang; Wei, Jingsong

    2012-09-01

    Bismuth-doped antimony-based (Sb100- x Bi x , x=2.46) thin films were presented as a functional mask for super-resolution readout of read-only memory (ROM). The pit size of the ROM was 390 nm, and super-resolution readout was realized on a dynamic tester with laser wavelength of 780 nm and the numerical aperture of the focusing objective lens of 0.45. The carrier-to-noise ratio (CNR) of 22 dB, readout threshold power of 0.8 mW and super-resolution readout cycles of 2×104 was achieved. The influence of film thickness and readout power on CNR was investigated. The reflectivity and transmittance of the film with different temperature at wavelength of 780 nm were detected, and the super-resolution mechanism of the bismuth-doped antimony-based thin films as the functional mask layer was discussed.

  20. Ultra-low carrier concentration and surface-dominant transport in antimony-doped Bi2Se3 topological insulator nanoribbons

    Science.gov (United States)

    Hong, Seung Sae; Cha, Judy J.; Kong, Desheng; Cui, Yi

    2012-03-01

    A topological insulator is the state of quantum matter possessing gapless spin-locking surface states across the bulk band gap, which has created new opportunities from novel electronics to energy conversion. However, the large concentration of bulk residual carriers has been a major challenge for revealing the property of the topological surface state by electron transport measurements. Here we report the surface-state-dominant transport in antimony-doped, zinc oxide-encapsulated Bi2Se3 nanoribbons with suppressed bulk electron concentration. In the nanoribbon with sub-10-nm thickness protected by a zinc oxide layer, we position the Fermi levels of the top and bottom surfaces near the Dirac point by electrostatic gating, achieving extremely low two-dimensional carrier concentration of 2×1011 cm-2. The zinc oxide-capped, antimony-doped Bi2Se3 nanostructures provide an attractive materials platform to study fundamental physics in topological insulators, as well as future applications.

  1. Antimoniais empregados no tratamento da leishmaniose: estado da arte Antimonials employed in the treatment of leishmaniaisis: the state of the art

    OpenAIRE

    Susanne Rath; Luciano Augusto Trivelin; Talitha Rebecca Imbrunito; Daniela Maria Tomazela; Marcelo Nunes de Jesús; Percy Calvo Marzal; Heitor Franco de Andrade Junior; André Gustavo Tempone

    2003-01-01

    Antimony preparations are the drugs of choice for the treatment of leishmaniasis over 90 years, a disease that currently affects 12 million people worldwide. Its introduction was based on 19th century concepts of therapeutic effects of metal salts as arsenicals and other metals, most of them abandoned due to toxic effects or better drugs. In the last three decades, there was a great improvement in the knowledge of cell biology and immunology of those infections, but chemotherapy has not been ...

  2. Decreased antimony uptake and overexpression of genes of thiol metabolism are associated with drug resistance in a canine isolate of Leishmania infantum

    OpenAIRE

    Verónica Gómez Pérez; Raquel García-Hernandez; Victoriano Corpas-López; Tomás, Ana M.; Joaquina Martín-Sanchez; Santiago Castanys; Francisco Gamarro

    2016-01-01

    Visceral leishmaniasis (VL) caused by the protozoan parasite Leishmania infantum, is one of the most important zoonotic diseases affecting dogs and humans in the Mediterranean area. The presence of infected dogs as the main reservoir host of L. infantum is regarded as the most significant risk for potential human infection. We have studied the susceptibility profile to antimony and other anti-leishmania drugs (amphotericin B, miltefosine, paromomycin) in Leishmania infantum isolates extracted...

  3. Arsenic and antimony determination in refined and unrefined table salts by means of hydride generation atomic absorption spectrometry--comparison of sample decomposition and determination methods

    OpenAIRE

    AKSUNER, Nur; TİRTOM, Vedia Nüket; HENDEN, Emür

    2011-01-01

    An evaluation was made of different digestion methods for the determination of arsenic and antimony in table salt samples prior to hydride generation atomic absorption spectrometric analysis. Microwave acid digestion, classical wet digestion, dry ashing, and fusion were applied to the decomposition of salt samples and optimum conditions were investigated. Samples were decomposed by changing heating time, digestion techniques, and the amount and composition of acid, and then the concen...

  4. Antimony determination in seawater and pore water of marine sediments by means of coprecipitation with Mg(OH)2 and atomic absorption spectrometry

    International Nuclear Information System (INIS)

    The study of biogeochemical cycling of trace elements in inshore marine environment is of basic importance in order to understand the long-term distribution of both conventional and radioactive pollutants among the ecosystem components. Antimony is of radio- ecological interest, and its determination in some environmental matrices (seawater, pore water, biota) is always difficult from the analytical point of view. A quick method for antimony determination in seawater and interstitial water of marine sediments, by coprecipitation with Mg(OH)2 and subsequent atomic absorption measurement, is reported. Coprecipitation recovery (about 80% in optimal conditions) was evaluated using both radiotracers and the addition of known amounts of stable element, and turned out to depend on several parameters (percentage of precipitated Mg as compared to the natural content in seawater, ageing of Mg(OH)2, concomitant Fe and Mn concentrations, etc.). The total standard deviation of the proposed method is about 10%. The variance analysis showed that about 90% of total variance is due to the preconcentration procedure (sample handling and random contaminations) and only about 10% is due to the instrumental measurement. The results of antimony determinations in seawater and pore water of marine sediments collected at Montalto di Castro (Central Mediterranean Sea) are presented and discussed

  5. 原子荧光光谱法测定环境空气中锑%Antimony Determination by Atomic Fluorescence Spectrometry

    Institute of Scientific and Technical Information of China (English)

    顾志勇

    2014-01-01

    采用过氯乙烯滤膜采集环境空气中锑,盐酸-氢氟酸混酸体系微波消解滤膜,原子荧光光谱法测定锑。方法前处理操作过程简单、省时、酸用量少、环境污染小,方法的灵敏度和准确度都有很大的提高。采样体积为300L时,空气中锑的最低检出质量浓度为0.002mg/m3。%Antimony in air was sampled using perchloroethylene filter.The filter was dipped into hydrochloric acid and hydrofluoric acid system and digested by microwave.Atomic fluorescence spectrometry was used to detect anti-mony after.This process is simple and time-saving with easy pretreatment,less amount of acid,and less negative impacts on environment.In addition,the accuracy and precision of the process is better than previous methods. The detection limit of antimony in air is 0.002mg/m3 when the volume of air sample is 300 liters when this process was applied.

  6. Analysis of arsenic and antimony distribution within plants growing at an old mine site in Ouche (Cantal, France) and identification of species suitable for site revegetation.

    Science.gov (United States)

    Jana, Ulrike; Chassany, Vincent; Bertrand, Georges; Castrec-Rouelle, Maryse; Aubry, Emmanuel; Boudsocq, Simon; Laffray, Daniel; Repellin, Anne

    2012-11-15

    One of the objectives of this study was to assess the contamination levels in the tailings of an old antimony mine site located in Ouche (Cantal, France). Throughout the 1.3 ha site, homogenous concentrations of antimony and arsenic, a by-product of the operation, were found along 0-0.5 m-deep profiles. Maximum concentrations for antimony and arsenic were 5780 mg kg(-1) dry tailings and 852 mg kg(-1) dry tailings, respectively. Despite the presence of the contaminants and the low pH and organic matter contents of the tailings, several patches of vegetation were found. Botanical identification determined 12 different genera/species. The largest and most abundant plants were adult pines (Pinus sylvestris), birches (Betula pendula) and the bulrush (Juncus effusus). The distribution of the metalloids within specimens of each genera/species was analysed in order to deduce their concentration and translocation capacities. This was the second goal of this work. All plant specimens were highly contaminated with both metalloids. Most were root accumulators with root to shoot translocation factors Plantago major, and Deschampsia flexuosa. PMID:22789654

  7. High frequency of skin reactions in patients with leishmaniasis treated with meglumine antimoniate contaminated with heavy metals: a comparative approach using historical controls

    Directory of Open Access Journals (Sweden)

    Romero Gustavo Adolfo Sierra

    2003-01-01

    Full Text Available We analyzed data from historical controls treated with meglumine antimoniate to compare the frequency of adverse events observed in patients with cutaneous leishmaniasis treated with the same dose of meglumine antimoniate contaminated with heavy metals in an endemic area of the State of Bahia, Brazil. Group A patients were treated in 2000 with the drug produced by Eurofarma Laboratórios Ltda., São Paulo, Brazil (lot A and group B patients were treated in 1996 with the reference drug produced by Rhodia Farma Ltda., São Paulo, Brazil (lot B. We observed an unusual higher frequency of skin reactions in group A patients. However, all type of adverse events observed in group A were also observed in group B. The physico-chemical analysis of these lots revealed that lot A had lower pH and higher concentration of total and trivalent antimony, lead, cadmium, and arsenic. Our findings suggest that the skin reactions could be attributed to heavy metal contamination of lot A.

  8. High frequency of skin reactions in patients with leishmaniasis treated with meglumine antimoniate contaminated with heavy metals: a comparative approach using historical controls.

    Science.gov (United States)

    Romero, Gustavo Adolfo Sierra; Flores M, Rico Marlon de Moraes; Noronha, Elza Ferreira; Macêdo, Vanize de Oliveira

    2003-01-01

    We analyzed data from historical controls treated with meglumine antimoniate to compare the frequency of adverse events observed in patients with cutaneous leishmaniasis treated with the same dose of meglumine antimoniate contaminated with heavy metals in an endemic area of the State of Bahia, Brazil. Group A patients were treated in 2000 with the drug produced by Eurofarma Laborat rios Ltda., S o Paulo, Brazil (lot A) and group B patients were treated in 1996 with the reference drug produced by Rhodia Farma Ltda., S o Paulo, Brazil (lot B). We observed an unusual higher frequency of skin reactions in group A patients. However, all type of adverse events observed in group A were also observed in group B. The physico-chemical analysis of these lots revealed that lot A had lower pH and higher concentration of total and trivalent antimony, lead, cadmium, and arsenic. Our findings suggest that the skin reactions could be attributed to heavy metal contamination of lot A.

  9. A green analytical procedure for sensitive and selective determination of antimony in environmental and biological samples by ligandless cloud point extraction

    Science.gov (United States)

    Rezaei, Vida; Samadi-Maybodi, Abdolraouf

    2012-09-01

    A very simple, environmental friendly and sensitive method based on the cloud point extraction (CPE) separation and spectrophotometric detection has been developed for the determination of antimony. The method is founded on the color reaction of Sb (III) with iodide in acidic medium and subsequent micelle-mediated extraction of the product using the non-ionic surfactant, Triton X-114, in the absence of any chelating agent. The Effects of reaction and extraction parameters were studied and optimum conditions were established. The calibration graph was linear in the range of 0.80-95 ng mL-1 of antimony in the initial solution with r = 0.9994 (n = 9). Detection limit based on three times the standard deviation of the blank (3Sb) was 0.23 ng mL-1 and the relative standard deviation (R.S.D.) for 10 and 70 ng mL-1 of antimony were 3.32 and 1.85% (n = 8), respectively. The proposed method was compared with other methods and favorably applied to evaluate this metal in some real samples, including seawater, antileishmanial drug (glucantime) and human serum.

  10. Flame-retardancy of a Cellulosic Fabric by the Application of Synergistic Effect between Ammonium Bromide and Antimony (Ⅲ)Oxide

    Institute of Scientific and Technical Information of China (English)

    MOSTASHARI Seyed Morteza; MOAFI Hadi Fallah

    2009-01-01

    The synergistic effect between ammonium bromide and antimony(Ⅲ) oxide as a nondurable finish on the flammability of 100% woven plain cotton fabric(with a density of 144 g/m2,the number of yarns 21 per 10 mm),has been investigated in this study. The laundered totally-dried, weighed specimens were impregnated with suitable concentration individual aqueous ammonium bromide and/or antimony (Ⅲ)oxide suspension solutions and some sets weIle impregnated with appropriate admixed solutions of the both chemicals.A vertical flame spread test Was then carried-out to characterize the flammability of the samples.An acceptable synergistic effect was then experi.enced by using an admixed bath containing 0.1 molar ammonium bromide and O.05 unit formal antimony trioxide solutions for impartation of flame.retardancy to a cotton fabric.The optimum mass of the mixture required to lm.Dart flame-retardancy was about 3.64 g of anhydrous additives per 100 g of fabric.The results obtained are in favor 0f Wall Effect Theory.Moreover synergistic eflfect indicating dehydration of the treated substrate by using this combination via thermogravimetry could be deduced.

  11. Spectral determination admixture of tin, antimony, lead, germanium by the method of fluoride sublimation

    International Nuclear Information System (INIS)

    In article introduced spectrographic investigation of selective treatment of Sn, Pb, Sb, Ge in form of their volatile fluoride, which are the product of decomposition of synthesized fluorine complex with iron

  12. Synthesis and structural characterization of new dithiocarbamate complexes from Sb(III) and Bi(III)

    Energy Technology Data Exchange (ETDEWEB)

    Jamaluddin, Nur Amirah; Baba, Ibrahim [School of Chemical Sciences and Food Technology, Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 43600 Bangi, Selangor (Malaysia)

    2013-11-27

    Twenty new antimony and bismuth dithiocarbamate complexes which employed ten different type of amines have been successfully synthesized. The synthesized complexes with metal to dithiocarbamate ratio at 1:3. Elemental analysis of the complexes gave the general formula of MCl[S{sub 2}CNR’R”]{sub 2} where M = Sb(III), Bi(III); R’ = methyl, ethyl, propyl, isopropyl, butyl, sec-butyl, benzyl; R” = ethanol, methyl, ethyl, propyl, isopropyl, cyclohexyl, benzyl. The complexes were analysed by IR and NMR spectroscopy. The crystal structure of five-coordinated antimony (III) complex have been determined by X-ray single crystal diffraction. Single crystal X-ray diffraction studies on SbCl[S{sub 2}CN(C{sub 4}H{sub 9})(C{sub 2}H{sub 5})]{sub 2} adopted a triclinic system with a space group P1 with a = 10.0141(8) Å, b = 10.1394(7) Å, c = 11.8665(9) Å, α = 67.960°, β =87.616°, γ = 80.172°.

  13. Quantitative study of the effect of deposition temperature on antimony incorporation in InAs/InAsSb superlattices

    Science.gov (United States)

    Haugan, H. J.; Mahalingam, K.; Szmulowicz, F.; Brown, G. J.

    2016-02-01

    InAs/InAsSb superlattices (SLs) are being actively explored for infrared detector applications owing to their superior carrier lifetimes. However, antimony (Sb) segregation during growth can alter the properties of the grown material. In this study, using X-ray energy dispersive spectrometry, authors quantify the compositional profile of individual layers and establish epitaxial parameters for high-quality InAs/InAsSb SL materials. Epitaxial conditions are determined for a nominal 7.7 nm InAs/3.5 nm InAs0.7Sb0.3 SL structure tailored for an approximately 6 μm response at 150 K. Since the growth of mixed anion alloys is complicated by the potential reaction of As2 with Sb surfaces, authors varied the deposition temperature (Tg) in order to control As2 surface reactions on Sb surfaces. Authors find that Sb incorporation is suppressed by 21%, with the increase of Tg from 395 to 440 °C. This incorporation likely stems from Sb surface segregation during InAsSb layer growth that is driven by the As-Sb exchange mechanism, which can lead to significant compositional and dimensional deviations from the intended design.

  14. Microbial degradation of high impact polystyrene (HIPS), an e-plastic with decabromodiphenyl oxide and antimony trioxide.

    Science.gov (United States)

    Sekhar, Vini C; Nampoothiri, K Madhavan; Mohan, Arya J; Nair, Nimisha R; Bhaskar, Thallada; Pandey, Ashok

    2016-11-15

    Accumulation of electronic waste has increased catastrophically and out of that various plastic resins constitute one of the leading thrown out materials in the electronic machinery. Enrichment medium, containing high impact polystyrene (HIPS) with decabromodiphenyl oxide and antimony trioxide as sole carbon source, was used to isolate microbial cultures. The viability of these cultures in the e-plastic containing mineral medium was further confirmed by triphenyl tetrazolium chloride (TTC) reduction test. Four cultures were identified by 16S rRNA sequencing as Enterobacter sp., Citrobacter sedlakii, Alcaligenes sp. and Brevundimonas diminuta. Biodegradation experiments were carried out in flask level and gelatin supplementation (0.1% w/v) along with HIPS had increased the degradation rate to a maximum of 12.4% (w/w) within 30days. This is the first report for this kind of material. The comparison of FTIR, NMR, and TGA analysis of original and degraded e-plastic films revealed structural changes under microbial treatment. Polystyrene degradation intermediates in the culture supernatant were also detected using HPLC analysis. The gravity of biodegradation was validated by morphological changes under scanning electron microscope. All isolates displayed depolymerase activity to substantiate enzymatic degradation of e-plastic.

  15. Lithium intercalation in sputter deposited antimony-doped tin oxide thin films: Evidence from electrochemical and optical measurements

    Energy Technology Data Exchange (ETDEWEB)

    Montero, J., E-mail: jose.montero@angstrom.uu.se; Granqvist, C. G.; Niklasson, G. A. [Department of Engineering Sciences, The A°ngström Laboratory, Uppsala University, P.O. Box 534, SE-751 21 Uppsala (Sweden); Guillén, C.; Herrero, J. [Department of Energy, Ciemat, Avda. Complutense 40, Ed. 42, E-28040 Madrid (Spain)

    2014-04-21

    Transparent conducting oxides are used as transparent electrical contacts in a variety of applications, including in electrochromic smart windows. In the present work, we performed a study of transparent conducting antimony-doped tin oxide (ATO) thin films by chronopotentiometry in a Li{sup +}-containing electrolyte. The open circuit potential vs. Li was used to investigate ATO band lineups, such as those of the Fermi level and the ionization potential, as well as the dependence of these lineups on the preparation conditions for ATO. Evidence was found for Li{sup +} intercalation when a current pulse was set in a way so as to drive ions from the electrolyte into the ATO lattice. Galvanostatic intermittent titration was then applied to determine the lithium diffusion coefficient within the ATO lattice. The electrochemical density of states of the conducting oxide was studied by means of the transient voltage recorded during the chronopotentiometry experiments. These measurements were possible because, as Li{sup +} intercalation took place, charge compensating electrons filled the lowest part of the conduction band in ATO. Furthermore, the charge insertion modified the optical properties of ATO according to the Drude model.

  16. Antimony segregation in Ge and formation of n-type selectively doped Ge films in molecular beam epitaxy

    International Nuclear Information System (INIS)

    Antimony segregation in Ge(001) films grown by molecular beam epitaxy was studied. A quantitative dependence of the Sb segregation ratio in Ge on growth temperature was revealed experimentally and modeled theoretically taking into account both the terrace-mediated and step-edge-mediated segregation mechanisms. A nearly 5-orders-of-magnitude increase in the Sb segregation ratio in a relatively small temperature range of 180–350 °C was obtained, which allowed to form Ge:Sb doped layers with abrupt boundaries and high crystalline quality using the temperature switching method that was proposed earlier for Si-based structures. This technique was employed for fabrication of different kinds of n-type Ge structures which can be useful for practical applications like heavily doped n+-Ge films or δ-doped layers. Estimation of the doping profiles sharpness yielded the values of 2–5 nm per decade for the concentration gradient at the leading edge and 2–3 nm for the full-width-half-maximum of the Ge:Sb δ-layers. Electrical characterization of grown Ge:Sb structures revealed nearly full electrical activation of Sb atoms and the two-dimensional nature of charge carrier transport in δ-layers

  17. Photocurrent Generation by Photosynthetic Purple Bacterial Reaction Centers Interfaced with a Porous Antimony-Doped Tin Oxide (ATO) Electrode.

    Science.gov (United States)

    Carey, Anne-Marie; Zhang, HaoJie; Mieritz, Daniel; Volosin, Alex; Gardiner, Alastair T; Cogdell, Richard J; Yan, Hao; Seo, Dong-Kyun; Lin, Su; Woodbury, Neal W

    2016-09-28

    The ability to exchange energy and information between biological and electronic materials is critical in the development of hybrid electronic systems in biomedicine, environmental sensing, and energy applications. While sensor technology has been extensively developed to collect detailed molecular information, less work has been done on systems that can specifically modulate the chemistry of the environment with temporal and spatial control. The bacterial photosynthetic reaction center represents an ideal photonic component of such a system in that it is capable of modifying local chemistry via light-driven redox reactions with quantitative control over reaction rates and has inherent spectroscopic probes for monitoring function. Here a well-characterized model system is presented, consisting of a transparent, porous electrode (antimony-doped tin oxide) which is electrochemically coupled to the reaction center via a cytochrome c molecule. Upon illumination, the reaction center performs the 2-step, 2-electron reduction of a ubiquinone derivative which exchanges with oxidized quinone in solution. Electrons from the electrode then move through the cytochrome to reoxidize the reaction center electron donor. The result is a facile platform for performing redox chemistry that can be optically and electronically controlled in time and space.

  18. A novel voltammetric sensor based on carbon nanotubes and nanoparticles of antimony tin oxide for the determination of ractopamine.

    Science.gov (United States)

    Baytak, Aysegul Kutluay; Teker, Tugce; Duzmen, Sehriban; Aslanoglu, Mehmet

    2016-02-01

    An electrochemical sensor was prepared by the modification of a glassy carbon electrode (GCE) with carbon nanotubes (CNTs) and nanoparticles of antimony tin oxide (ATO). The surface layer was characterized by scanning electronmicroscopy (SEM), energy dispersive X-ray diffraction method (EDX) and ATR FT-IR spectroscopy. The proposed electrode was assessed in respect to the electro-oxidation of ractopamine. Compared with a bare GCE and a GCE electrode modified with CNTs, the ATONPs/CNTs/GCE exhibited a great catalytic activity towards the oxidation of ractopamine with a well-defined anodic peak at 600 mV. The current response was linear with the concentration of ractopamine over the range from 10 to 240 nM with a detection limit of 3.3 nM. The proposed electrode enabled the selective determination of ractopamine in the presence of high concentrations of ascorbic acid (AA), dopamine (DA) and uric acid (UA). The proposed electrode was successfully applied for the determination of ractopamine in feed and urine samples. The sensitive and selective determination of ractopamine makes the developed method of great interest for monitoring its therapeutic use and doping control purposes. PMID:26652385

  19. A green synthesis route for the phase and size tunability of copper antimony sulfide nanocrystals with high yield.

    Science.gov (United States)

    Chen, Keqiang; Zhou, Jing; Chen, Wen; Chen, Qiao; Zhou, Peng; Liu, Yueli

    2016-03-01

    Until now, it is a great challenge for the controllable synthesis of copper antimony sulfide (CAS) nanocrystals (NCs), as the reactivity of precursors is quite difficult to be controlled during the synthesis process. In the present work, a novel solution-based method is proposed to synthesize CAS NCs by choosing N,N'-diphenylthiourea as the sulfide precursor, which is favorable for balancing the relative reactivity of Cu and Sb ions. It is found that three phases (CuSbS2, Cu12Sb4S13 and Cu3SbS4) of CAS NCs with size tunability were successfully synthesized for the first time. To the best of our knowledge, the lowest reaction temperature of 110 °C and the highest yield over 90% for CAS NCs were also achieved for the first time, which may be considered to be a green synthesis route compared with other conventional methods. Optical properties indicate that the as-prepared CAS NCs have strong optical absorption in the visible light region of the solar spectrum, and we also observed the band gap tunability of CuSbS2 and Cu3SbS4 materials for the first time. PMID:26875832

  20. FACTORS ASSOCIATED TO ADHERENCE TO DIFFERENT TREATMENT SCHEMES WITH MEGLUMINE ANTIMONIATE IN A CLINICAL TRIAL FOR CUTANEOUS LEISHMANIASIS

    Directory of Open Access Journals (Sweden)

    Madelon Novato Ribeiro

    2014-07-01

    Full Text Available The favorable outcome of the treatment of a disease is influenced by the adherence to therapy. Our objective was to assess factors associated with adherence to treatment of patients included in a clinical trial of equivalence between the standard and alternative treatment schemes with meglumine antimoniate (MA in the treatment of cutaneous leishmaniasis (CL, in the state of Rio de Janeiro. Between 2008 and 2011, 57 patients with CL were interviewed using a questionnaire to collect socioeconomic data. The following methods were used for adherence monitoring: counting of vial surplus, monitoring card, Morisky test and modified Morisky test (without the question regarding the schedule; we observed 82.1% (vial return, 86.0% (monitoring card, 66.7% (Morisky test and 86.0% (modified Morisky test adherence. There was a strong correlation between the method of vial counting and the monitoring card and modified Morisky test. A significant association was observed between greater adherence to treatment and low dose of MA, as well as with a lower number of people sleeping in the same room. We recommend the use of the modified Morisky test to assess adherence to treatment of CL with MA, because it is a simple method and with a good performance, when compared to other methods.

  1. Arsenic and antimony in water and wastewater: overview of removal techniques with special reference to latest advances in adsorption.

    Science.gov (United States)

    Ungureanu, Gabriela; Santos, Sílvia; Boaventura, Rui; Botelho, Cidália

    2015-03-15

    Arsenic and antimony are metalloids, naturally present in the environment but also introduced by human activities. Both elements are toxic and carcinogenic, and their removal from water is of unquestionable importance. The present article begins with an overview of As and Sb chemistry, distribution and toxicity, which are relevant aspects to understand and develop remediation techniques. A brief review of the recent results in analytical methods for speciation and quantification was also provided. The most common As and Sb removal techniques (coagulation/flocculation, oxidation, membrane processes, electrochemical methods and phyto and bioremediation) are presented with discussion of their advantages, drawbacks and the main recent achievements. Literature review on adsorption and biosorption were focused in detail. Considering especially the case of developing countries or rural communities, but also the finite energy resources that over the world are still dependent, recent research have focused especially readily available low-cost adsorbents, as minerals, wastes and biosorbents. Many of these alternative sorbents have been presenting promising results and can be even superior when compared to the commercial ones. Sorption capacities were accurately compiled for As(III,V) and Sb(III,V) species in order to provide to the reader an easy but detailed comparison. Some aspects related to experimental conditions, comparison criteria, lack of research studies, economic aspects and adsorption mechanisms were critically discussed. PMID:25585146

  2. Quadrupole coupling constants and isomeric Moessbauer shifts for halogen-containing gold, platinum, niobium, tantalum and antimony compounds

    International Nuclear Information System (INIS)

    We have analyzed by means of Density functional theory calculations the nuclear quadrupole coupling constants of a range of gold, antimony, platinum, niobium and tantalum compounds. The geometrical parameters and halogen nuclear quadrupole coupling constants obtained by these calculations substantially corresponded to the data of microwave and nuclear quadrupole resonance spectroscopy. An analysis of the quality of the calculations that employ pseudo-potentials and all-electron basis sets for the halogen compounds was carried out. The zero order regular approximation (ZORA) method is shown to be a viable alternative for the calculation of halogen coupling constants in molecules. In addition, the ZORA model, in contrast to the pseudo-potential model, leads to realistic values of all metal nuclear quadrupole coupling constants. From Klopman's approach, it follows that the relationship between the electrostatic bonding and covalent depends on the nature of the central atom. The results on Moessbauer chemical shifts are also in a good agreement with the coordination number of the central atom.

  3. Use of cloud-point preconcentration for spectrophotometric determination of trace amounts of antimony in biological and environmental samples.

    Science.gov (United States)

    El-Sharjawy, Abdel-Azeem M; Amin, Alaa S

    2016-01-01

    This work presents a cloud-point extraction process using the micelle-mediated extraction method for simultaneous preconcentration and determination of Sb(III) and Sb(V) species in biological and environmental samples as a prior preconcentration step to their spectrophotometric determination. The analytical system is based on the selective reaction between Sb(III) and 3-dichloro-6-(3-carboxy-2-hydroxy-1-naphthylazo)quinoxaline (DCHNAQ) in the presence of cetyltrimethylammonium bromide (CTAB) and potassium iodide at pH 4.5. Total Sb concentration was determined after reduction of Sb(V) to Sb(III) in the presence of potassium iodide and ascorbic acid. The optimal reaction conditions and extraction were studied, and the analytical characteristics of the method (e.g., limits of detection and quantification, linear range, preconcentration, improvement factors) were obtained. Linearity for Sb(III) was obeyed in the range of 0.2-20 ng ml(-1). The detection and quantification limits for the determination of Sb(III) were 0.055 and 0.185 ng ml(-1), respectively. The method has a lower detection limit and wider linear range, inexpensive instrument, and low cost, and is more sensitive compared with most other methods. The interference effect of some anions and cations was also studied. The method was applied to the determination of Sb(III) in the presence of Sb(V) and total antimony in blood plasma, urine, biological, and water samples.

  4. Profiling microbial community in a watershed heavily contaminated by an active antimony (Sb) mine in Southwest China.

    Science.gov (United States)

    Sun, Weimin; Xiao, Enzong; Dong, Yiran; Tang, Song; Krumins, Valdis; Ning, Zengping; Sun, Min; Zhao, Yanlong; Wu, Shiliang; Xiao, Tangfu

    2016-04-15

    Located in Southwest China, the Chahe watershed has been severely contaminated by upstream active antimony (Sb) mines. The extremely high concentrations of Sb make the Chahe watershed an excellent model to elucidate the response of indigenous microbial activities within a severe Sb-contaminated environment. In this study, water and surface sediments from six locations in the Chahe watershed with different levels of Sb contamination were analyzed. Illumina sequencing of 16S rRNA amplicons revealed more than 40 phyla from the domain Bacteria and 2 phyla from the domain Archaea. Sequences assigned to the genera Flavobacterium, Sulfuricurvum, Halomonas, Shewanella, Lactobacillus, Acinetobacter, and Geobacter demonstrated high relative abundances in all sequencing libraries. Spearman's rank correlations indicated that a number of microbial phylotypes were positively correlated with different speciation of Sb, suggesting potential roles of these phylotypes in microbial Sb cycling. Canonical correspondence analysis further demonstrated that geochemical parameters, including water temperature, pH, total Fe, sulfate, aqueous Sb, and Eh, significantly structured the overall microbial community in Chahe watershed samples. Our findings offer a direct and reliable reference to the diversity of microbial communities in the presence of extremely high Sb concentrations, and may have potential implications for in situ bioremediation strategies of Sb contaminated sites. PMID:26820933

  5. NMR study of the reactions of tin(2) difluoride and antimony(3) trifluoride with niobium pentachloride

    International Nuclear Information System (INIS)

    Interaction of SnF2 and SbF3 with NbCl5 in solutions of acetonitrile and dimethylsulfoxide was studied by the method of 19F, 93Nb, 119Sn NMR. It is shown that anionic octahedral chlorofluoride complexes of niobium are formed in acetonitrile, while neutral ones- in dimethylsulfoxide. SnF2 and SnF3 are effective sources of fluorine ions when preparing fluorochloride and fluoride compounds of niobium

  6. STUDY ON THE REMOVAL OF ANTIMONY FOR PRODUCING SODIUM STANNATE BY TIN SLAG%锡渣生产锡酸钠中除锑的研究

    Institute of Scientific and Technical Information of China (English)

    卢丹艳

    2012-01-01

    利用生产硫酸亚锡、氯化亚锡、锡:扮的含锡废料生产锡酸钠,生产成本低,但在这过程中需要除去的杂质也相对比较多。文章对除锑的工艺参数和条件进行了研究,重点探讨了除锑温度、除锑时间、除锑后溶液静置沉降时间等因素对锑效果的影响。结果表明,采用该工艺,Sb的脱除率为95.3%,产品质量符合Sn-42等级标准。%waste material that contains tin and can be used for producing Stannous sulfate, Stannous chloride and Tin powder is use for producing Sodium stannate. The cost of production may stay at a relative low level. But It needs to get rid of More impurities, Relatively speaking .In this paper, the process parameters and conditions of the removal of Antimony are studied. The factors such as the temperature and time of the removal of Antimony and time of sedimentation time of the Solution are discussed, which have an influence on the removal of Antimony. It is shown that, using this technology, removal rate of Sb is 95.3%, and the Product quality is In accordance with the grading standard of Sn 42.

  7. Development of a non-chromatographic method for the speciation analysis of inorganic antimony in mushroom samples by hydride generation atomic fluorescence spectrometry

    Science.gov (United States)

    Sousa Ferreira, Hadla; Costa Ferreira, Sergio Luis; Cervera, M. Luisa; de la Guardia, Miguel

    2009-06-01

    A simple and sensitive method has been developed for the direct determination of toxic species of antimony in mushroom samples by hydride generation atomic fluorescence spectrometry (HG AFS). The determination of Sb(III) and Sb(V) was based on the efficiency of hydride generation employing NaBH 4, with and without a previous KI reduction, using proportional equations corresponding to the two different measurement conditions. The extraction efficiency of total antimony and the stability of Sb(III) and Sb(V) in different extraction media (nitric, sulfuric, hydrochloric, acetic acid, methanol and ethanol) were evaluated. Results demonstrated that, based on the extraction yield and the stability of extracts, 0.5 mol L - 1 H 2SO 4 proved to be the best extracting solution for the speciation analysis of antimony in mushroom samples. The limits of detection of the developed methodology were 0.6 and 1.1 ng g - 1 for Sb(III) and Sb(V), respectively. The relative standard derivation was 3.8% (14.7 ng g - 1 ) for Sb(V) and 5.1% (4.6 ng g - 1 ) for Sb(III). The recovery values obtained for Sb(III) and Sb(V) varied from 94 to 106% and from 98 to 105%, respectively. The method has been applied to determine Sb(III), Sb(V) and total Sb in five different mushroom samples; the Sb(III) content varied from 4.6 to 11.4 ng g - 1 and Sb(V) from 14.7 to 21.2 ng g - 1 . The accuracy of the method was confirmed by the analysis of a certified reference material of tomato leaves.

  8. Preparation of Highly Dispersed Antimony-doped Tin Oxide Nano-powder via Ion-exchange Hydrolysis of SnCl4 and SbCl3 and Azeotropic Drying

    Institute of Scientific and Technical Information of China (English)

    YANG Fen; ZHANG Xue-jun; TIAN Fang; WU Xu; GAN Fu-xing

    2007-01-01

    Antimony-doped tin hydroxide colloid precipitates have been synthesized by hydrolysis of SnCl4 and SbCl3 using: (1) an ion-exchange hydrolysis to remove chlorine ions, and (2) isoamyl acetate as an azeotropic solvent to obviate water. The obtained dried powder is of high dispersivity without any need for further grinding. The size and dispersivity of the final particles are investigated with the aid of TG-DTA, BET, XRD and TEM. After having calcined, the antimony-doped tin oxide nanopowder possesses a tetragonal rutile structure with high dispersivity, uniform particles and low hard agglomeration.

  9. Facilitated extracellular electron transfer of Shewanella loihica PV-4 by antimony-doped tin oxide nanoparticles as active microelectrodes

    Science.gov (United States)

    Zhang, Xiaojian; Liu, Huan; Wang, Jinrong; Ren, Guangyuan; Xie, Beizhen; Liu, Hong; Zhu, Ying; Jiang, Lei

    2015-11-01

    Dissimilatory metal reducing bacteria are capable of extracellular electron transfer (EET) to insoluble metal oxides as external electron acceptors for their anaerobic respiration, which is recognized as an important energy-conversion process in natural and engineered environments, such as in mineral cycling, bioremediation, and microbial fuel/electrolysis cells. However, the low EET efficiency remains one of the major bottlenecks for its practical application. We report firstly that the microbial current generated by Shewanella loihica PV-4 (S. loihica PV-4) could be greatly improved that is up to ca. 115 fold, by adding antimony-doped tin oxide (ATO) nanoparticles in the electrochemical reactor. The results demonstrate that the biocompatible, electrically conductive ATO nanoparticles acted as active microelectrodes could facilitate the formation of a cells/ATO composite biofilm and the reduction of the outer membrane c-type cytochromes (OM c-Cyts) that are beneficial for the electron transfer from cells to electrode. Meanwhile, a synergistic effect between the participation of OM c-Cyts and the accelerated EET mediated by cell-secreted flavins may play an important role for the enhanced current generation in the presence of ATO nanoparticles. Moreover, it is worth noting that the TCA cycle in S. loihica PV-4 cells is activated by adding ATO nanoparticles, even if the potential is poised at +0.2 V, thereby also improving the EET process. The results presented here may provide a simple and effective strategy to boost the EET of S. loihica PV-4 cells, which is conducive to providing potential applications in bioelectrochemical systems.Dissimilatory metal reducing bacteria are capable of extracellular electron transfer (EET) to insoluble metal oxides as external electron acceptors for their anaerobic respiration, which is recognized as an important energy-conversion process in natural and engineered environments, such as in mineral cycling, bioremediation, and

  10. Effect of the antimony thin-film deposition sequence on copper-silicon interdiffusion: Vpliv zaporedja nanosa tankih plasti antimona na interdifuzijo baker-silicij:

    OpenAIRE

    Chaouki, Benazzouz; Fouzia, Zekkar; Mahfoud, Benkerri; Mokhtar, Boudissa; Mounir, Reffas; Nasser, Menni

    2012-01-01

    In this work we present a study of the effect of an antimony layer on the interdiffusion and formation of copper silicides while inverting the sequence of Cu and Sb deposition on Si(111) substrates. Thermal evaporation was used to deposit Cu/Sb and Sb/Cu bilayers on a Si(111) substrate heated at 100 °C, without breaking the vacuum. XRD and RBS analysis showed, for samples heat treated at 200 °C and 400 °C, a segregation of the three elements (i.e., Cu, Sb and Si) to the surface and diffusion ...

  11. Comparative study on the corrosion behavior of the cold rolled and hot rolled low-alloy steels containing copper and antimony in flue gas desulfurization environment

    Science.gov (United States)

    Park, S. A.; Kim, J. G.; He, Y. S.; Shin, K. S.; Yoon, J. B.

    2014-12-01

    The correlation between the corrosion and microstructual characteristics of cold rolled and hot rolled low-alloy steels containing copper and antimony was established. The corrosion behavior of the specimens used in flue gas desulfurization systems was examined by electrochemical and weight loss measurements in an aggressive solution of 16.9 vol % H2SO4 + 0.35 vol % HCl at 60°C, pH 0.3. It has been shown that the corrosion rate of hot rolled steel is lower than that of cold rolled steel. The corrosion rate of cold rolled steel was increased by grain refinement, inclusion formation, and preferred grain orientation.

  12. New and rapid access to synthesis of novel polysubstituted imidazoles using antimony trichloride and stannous chloride dihydrate as effective and reusable catalysts

    Indian Academy of Sciences (India)

    Leyla Poorali; Bahador Karami; Khalil Eskandari; Mahboobeh Azizi

    2013-05-01

    In this work, new, efficient and environmentally adapted synthesis of polysubstituted imidazoles in one-pot is repoted. The multicomponent reaction of various aldehydes, benzil, aliphatic and aromatic primary amines and ammonium acetate under solvent-free condition is explained. The highly efficient role of antimony trichloride and stannous chloride dihydrate as catalyst in this synthesis was shown and their effects on the reaction process were studied. By this advantage, several polysubstituted imidazoles as pharmaceutical important molecules can be prepared in high yield and high purity. This method is a very easy and rapid for the synthesis of imidazole derivatives.

  13. Double blind, randomized controlled trial, to evaluate the effectiveness of a controlled nitric oxide releasing patch versus meglumine antimoniate in the treatment of cutaneous leishmaniasis [NCT00317629

    Directory of Open Access Journals (Sweden)

    Silva Federico A

    2006-05-01

    Full Text Available Abstract Background Cutaneous Leishmaniasis is a worldwide disease, endemic in 88 countries, that has shown an increasing incidence over the last two decades. So far, pentavalent antimony compounds have been considered the treatment of choice, with a percentage of cure of about 85%. However, the high efficacy of these drugs is counteracted by their many disadvantages and adverse events. Previous studies have shown nitric oxide to be a potential alternative treatment when administered topically with no serious adverse events. However, due to the unstable nitric oxide release, the topical donors needed to be applied frequently, making the adherence to the treatment difficult. The electrospinning technique has allowed the production of a multilayer transdermal patch that produces a continuous and stable nitric oxide release. The main objective of this study is to evaluate this novel nitric oxide topical donor for the treatment of cutaneous leishmaniasis. Methods and design A double-blind, randomized, double-masked, placebo-controlled clinical trial, including 620 patients from endemic areas for Leishmaniasis in Colombia was designed to investigate whether this patch is as effective as meglumine antimoniate for the treatment of cutaneous leishmaniasis but with less adverse events. Subjects with ulcers characteristic of cutaneous leishmaniasis will be medically evaluated and laboratory tests and parasitological confirmation performed. After checking the inclusion/exclusion criteria, the patients will be randomly assigned to one of two groups. During 20 days Group 1 will receive simultaneously meglumine antimoniate and placebo of nitric oxide patches while Group 2 will receive placebo of meglumine antimoniate and active nitric oxide patches. During the treatment visits, the medications will be daily administered and the presence of adverse events assessed. During the follow-up, the research group will visit the patients at days 21, 45, 90 and 180. The

  14. Preparation and Characterization of Antimony Doped Tin Oxide Thin Films Synthesized by Co-Evaporation of Sn and Sb using Plasma Assisted Thermal Evaporation

    Directory of Open Access Journals (Sweden)

    C. Jariwala

    2013-05-01

    Full Text Available Tin oxide (SnO2 thin films are having promising properties such as high visible transmittance and low electric resistivity, makes them very important transparent conductor in a variety of optoelectronics devices. Further, doping with pentavalent impurity such as Antimony (Sb enhances its conductivity considerably. In order to study the effect of Antimony doping, Antimony doped tin oxide (SnO2 : Sb thin films have been prepared by the co-evaporation of Sn and Sb using Plasma Assisted Thermal Evaporation (PATE in oxygen (O2 partial pressure at various doping level from 4% to 25%. The influence of various Sb doping levels on the compositional, electrical, optical and structural properties have been investigated using Energy Dispersive X-ray (EDX spectroscopy, Ultraviolet-Visible (UV-VIS transmission spectroscopy, four-probe resistivity measurement and X-ray Diffraction (XRD, respectively. EDX studies confirmed the different Sb doping levels in the grown films from 4 % to 25 %, while electrical resistivity is obtained in range of 0.36 to 9.5 Ohmcm using four-probe setup for 4 % to 25 % Sb doping levels. Transmittance spectra measured in UV-VIS range for Sb doped films show reduction in an average transmittance in respect to increase in Sb doping levels in the grown films. Whereas, XRD analysis reveals that higher Sb doping of 25 % induce the precipitation of antimony oxide (Sb2O3 phase and its precipitation suppressed the growth of SnO2 peaks as well as responsible for reduction in conductivity and transparency. The best electrical resistivity of optimized SnO2 : Sb (5 % is 0.36 Ohmcm without deteriorating the high (~ 80 % average transmittance in the wavelength region 300-800 nm in comparison to undoped SnO2 film (6.57 Ohmcm , confirm the usefulness of SnO2 : Sb (5 % films for device applications.

  15. Antimony (Sb) sorption studies on zircaloy, carbon steel (CS) and magnetite coated CS (MCS) surfaces in aqueous medium at pH 10.2 and 280℃

    International Nuclear Information System (INIS)

    Antimony sorption studies on zircaloy, CS and magnetite coated carbon steel (MCS) at primary heat transport temperature (290℃) of pressurised heavy water reactor (PHWR) are of direct relevance in investigating Sb activity problem faced in Indian PHWRs. Sb impregnated PHT pump carbon bearing releases Sb to reactor core. This Sb activates, and redeposit on out-of-core surfaces and results in exposure and apparent high decontamination factors. This Sb is not amenable to normal decantation. The form and state of deposited Sb is not yet fully known. This works attempts for this

  16. Molecular diversity of arbuscular mycorrhizal fungi at a large-scale antimony mining area in southern China.

    Science.gov (United States)

    Wei, Yuan; Chen, Zhipeng; Wu, Fengchang; Hou, Hong; Li, Jining; Shangguan, Yuxian; Zhang, Juan; Li, Fasheng; Zeng, Qingru

    2015-03-01

    Arbuscular mycorrhizal fungi (AMF) have great potential for assisting heavy metal hyperaccumulators in the remediation of contaminated soils. However, little information is available about the community composition of AMF under natural conditions in soils contaminated by antimony (Sb). The objective of this study was to investigate the characteristics of AMF molecular diversity, and to explore the effects of Sb content and soil properties on the AMF community structure in an Sb mining area. Four Sb mine spoils and one adjacent reference area were selected from around the Xikuangshan mine in southern China. The association of AMF molecular diversity and community composition with the rhizosphere soils of the dominant plant species was studied by Polymerase Chain Reaction-Denaturing Gradient Gel Electrophoresis (PCR-DGGE). Results from all five studied sites showed that the diversity of AMF decreased with increasing Sb concentration. Principal component analysis (PCA) indicated that the AMF community structure was markedly different among these groups. Further redundancy analysis (RDA) showed that Sb contamination was the dominating factor influencing the AMF community structure in the Sb mine area. However, the multivariate analysis showed that, apart from the soil Sb content, extractable nitrogen content and organic matter content also attributed to AMF sequence distribution type. Some AMF sequences were only found in the highly contaminated area and these might be ideal candidates for improving phytoremediation efficiency in Sb mining regions. Gene sequencing analysis revealed that most species were affiliated with Glomus, suggesting that Glomus was the dominant AMF genus in the studied Sb mining area. PMID:25766009

  17. Eficácia do sulfato de aminosidine na leishmaniose visceral grave, resistente ao tratamento com antimonial pentavalente

    Directory of Open Access Journals (Sweden)

    Cleudson Castro

    1995-09-01

    Full Text Available Descreve-se um caso de calazar grave resistente a dez cursos de antimonial petitavalente (glucantime à base de 20mg de Sb5/kg/dia, que respondeu favoravelmente ao sulfato de aminosidine intramuscular na dose de 20mg/kg/dia por 20 dias, repetido após 20 dias. O parasitismo esplénico passou de 50 parasitos por campo a 3 parasitos em 10 campos logo após a primeira série de sulfato de aminosidine, tornando-se negativo depois de sete meses. A melhora clínica foi imediata, com redução gradual da hepatoesplenomegalia, e desaparecimento 26 meses após. Neste período aumentou 13 kg. Após o uso de aminosidine a reação de Monténégro tornou-se positiva e as células mononucleares responderam quando estimuladas com antígenos de leishmânia.A grave kala-azar infection in a 14 years old boy is described. The leishmanial infection failed to respond to ten interrupted courses of glucantime of variable duration (14-56 days at a dose of 20mg Sb5/kg/day. However a favorable response ocurred to intramuscular aminosidine sulphate (20mg/kg/day for 20 days. This same regimen was repeated 20 days later. After the first treatment splenic puncture parasite density fell from 50 amastigotes per oil immersion field to 3 amastigotes in 10 fields. A further splenic puncture 7 months after treatment was negative. The marked hepatoesplenomegaly gradually resolved over 26 months follow up and he gained 13 kilogramas in weight. After aminosidine sulphate therapy his Montenegro reaction become positive and his lymphocytes responded to leishmania antigens.

  18. Imipramine is an orally active drug against both antimony sensitive and resistant Leishmania donovani clinical isolates in experimental infection.

    Directory of Open Access Journals (Sweden)

    Sandip Mukherjee

    Full Text Available BACKGROUND: In an endeavor to find an orally active and affordable antileishmanial drug, we tested the efficacy of a cationic amphiphilic drug, imipramine, commonly used for the treatment of depression in humans. The only available orally active antileishmanial drug is miltefosine with long half life and teratogenic potential limits patient compliance. Thus there is a genuine need for an orally active antileishmanial drug. Previously it was shown that imipramine, a tricyclic antidepressant alters the protonmotive force in promastigotes, but its in vivo efficacy was not reported. METHODOLOGY/PRINCIPAL FINDINGS: Here we show that the drug is highly active against antimony sensitive and resistant Leishmania donovani in both promastigotes and intracellular amastigotes and in LD infected hamster model. The drug was found to decrease the mitochondrial transmembrane potential of Leishmania donovani (LD promastigotes and purified amastigotes after 8 h of treatment, whereas miltefosine effected only a marginal change even after 24 h. The drug restores defective antigen presenting ability of the parasitized macrophages. The status of the host protective factors TNF α, IFN γ and iNOS activity increased with the concomitant decrease in IL 10 and TGF β level in imipramine treated infected hamsters and evolution of matured sterile hepatic granuloma. The 10-day therapeutic window as a monotherapy, showing about 90% clearance of organ parasites in infected hamsters regardless of their SSG sensitivity. CONCLUSIONS: This study showed that imipramine possibly qualifies for a new use of an old drug and can be used as an effective orally active drug for the treatment of Kala-azar.

  19. Bacillus sp.处理含锑废水试验研究%Bacillus sp. Treatment of Wastewater Containing Antimony

    Institute of Scientific and Technical Information of China (English)

    李小娇; 陈平; 陈才丽; 成应向; 龚道新; 向仁军; 王强强

    2013-01-01

    Antimony ore dressing wastewater was treated by using Bacil us sp. and the influences of treatment time, temperature, inoculation size, and pH value on Sb removal effect were explored. The results showed that the best removal efficiency of Sb in mineral processing wastewater could reach 99.75% in 4 d under the optimum conditions of 30 ℃, microbial inoculated quantity 5%, and pH value at 2.0. After the treatment, the concentration of Sb in wastewater was reduced from 122.21 to 0.30 mg/L, which was lower than the local industrial wastewater discharge standard of 0.50 mg/L.%利用某芽孢杆菌属微生物( Bacillus sp.)对锑矿选矿废水进行了处理。研究微生物的接种量、作用时间、温度、体系 pH值等对废水中Sb的去除效果的影响。结果表明:作用时间4 d微生物接种量为5处理体系 pH为2最佳处理体系温度为30时,效果最佳,对废水中Sb的去除率达到99.75%,处理后废水中 Sb的浓度由122.21 mg/L降低至0.30 mg/L,出水Sb浓度低于湖南省地方标准排放限值0.50 mg/L。

  20. Correlating microbial community profiles with geochemical conditions in a watershed heavily contaminated by an antimony tailing pond.

    Science.gov (United States)

    Xiao, Enzong; Krumins, Valdis; Tang, Song; Xiao, Tangfu; Ning, Zengping; Lan, Xiaolong; Sun, Weimin

    2016-08-01

    Mining activities have introduced various pollutants to surrounding aquatic and terrestrial environments, causing adverse impacts to the environment. Indigenous microbial communities are responsible for the biogeochemical cycling of pollutants in diverse environments, indicating the potential for bioremediation of such pollutants. Antimony (Sb) has been extensively mined in China and Sb contamination in mining areas has been frequently encountered. To date, however, the microbial composition and structure in response to Sb contamination has remained overlooked. Sb and As frequently co-occur in sulfide-rich ores, and co-contamination of Sb and As is observed in some mining areas. We characterized, for the first time, the microbial community profiles and their responses to Sb and As pollution from a watershed heavily contaminated by Sb tailing pond in Southwest China. The indigenous microbial communities were profiled by high-throughput sequencing from 16 sediment samples (535,390 valid reads). The comprehensive geochemical data (specifically, physical-chemical properties and different Sb and As extraction fractions) were obtained from river water and sediments at different depths as well. Canonical correspondence analysis (CCA) demonstrated that a suite of in situ geochemical and physical factors significantly structured the overall microbial community compositions. Further, we found significant correlations between individual phylotypes (bacterial genera) and the geochemical fractions of Sb and As by Spearman rank correlation. A number of taxonomic groups were positively correlated with the Sb and As extractable fractions and various Sb and As species in sediment, suggesting potential roles of these phylotypes in Sb biogeochemical cycling. PMID:27182975

  1. 甲基异丁基甲酮萃取—氢化物发生原子荧光光谱法测定锑锭和氧化锑中汞%Determination of mercury in antimony ingot and antimony oxide by methyl isobutyl ketone extraction-hydride generation atomic fluorescence spectrometry

    Institute of Scientific and Technical Information of China (English)

    陆建平; 谭芳维; 石建荣

    2012-01-01

    After the samples were dissolved in aqua regia/HBr and tartaric acid was added to mask antimony, then mercury in antimony ingot and antimony oxide was extracted into the organic phase with methyl isobutyl ketone (MIBK) and determined by organic phase injection-intermittent flow injection atomic fluorescence spectrometry. Sample dissolution methods and interferences caused by coexisting ions were investigated, and instrument working conditions, extraction conditions, acidity and other factors were optimized. The results showed that under optimal conditions, the mercury content within the range of 0. 02 to 50 μg/L was in good linear relationship, and the detection limit was 0. 013 jxg/L. This method was applied to the actual antimony ingot and antimony oxide sample analysis. It was found that the results were consistent with those obtained by inductive coupled plasma atomic emission spectrometry with relative standard deviations (RSDs, n = 6) of 0. 65%-2. 4% and recoveries of 94 %-99%.%采用王水/HBr溶解样品,酒石酸掩蔽锑,用甲基异丁基甲酮(MIBK)将汞萃取到有机相中,建立了有机相进样—断续流动注射原子荧光光谱法测定锑锭和氧化锑中汞含量的方法.研究了溶样方法和共存离子可能引起的干扰,优化了仪器工作条件、萃取条件、酸度及其他影响因素.结果表明,在最佳条件下,汞含量在0.02~50 μg/L范围内线性关系良好,方法检出限为0.013 μg/L.将方法应用于锑锭和氧化锑实际样品分析,测得结果与电感耦合等离子体原子发射光谱法一致,相对标准偏差(RSD,n=6)在0.65%~2.4%之间,加标回收率为94%~99%.

  2. Ultra-low carrier concentration and surface-dominant transport in antimony-doped Bi2Se3 topological insulator nanoribbons

    KAUST Repository

    Hong, Seung Sae

    2012-03-27

    A topological insulator is the state of quantum matter possessing gapless spin-locking surface states across the bulk band gap, which has created new opportunities from novel electronics to energy conversion. However, the large concentration of bulk residual carriers has been a major challenge for revealing the property of the topological surface state by electron transport measurements. Here we report the surface-state-dominant transport in antimony-doped, zinc oxide-encapsulated Bi2Se3 nanoribbons with suppressed bulk electron concentration. In the nanoribbon with sub-10-nm thickness protected by a zinc oxide layer, we position the Fermi levels of the top and bottom surfaces near the Dirac point by electrostatic gating, achieving extremely low two-dimensional carrier concentration of 2×10 11cm-2. The zinc oxide-capped, antimony-doped Bi 2Se3 nanostructures provide an attractive materials platform to study fundamental physics in topological insulators, as well as future applications. © 2012 Macmillan Publishers Limited. All rights reserved.

  3. Stability studies of arsenic, selenium, antimony and tellurium species in water, urine, fish and soil extracts using HPLC/ICP-MS

    Energy Technology Data Exchange (ETDEWEB)

    Lindemann, T.; Prange, A.; Neidhart, B. [GKSS Research Centre, Geesthacht (Germany). Inst. of Physical and Chemical Analysis; Dannecker, W. [Hamburg Univ. (Germany). Inst. fuer Anorganische und Angewandte Chemie

    2000-10-01

    The stability of arsenic, selenium, antimony and tellurium species in water and urine (NIST SRM 2670n) as well as in extracts of fish and soil certified reference materials (DORM-2 and NIST SRM 2710) has been investigated. Stability studies were carried out with As(III), As(V), arsenobetaine, monomethylarsonic acid (MMA), dimethylarsinic acid (DMA), phenylarsonic acid (PAA), Se(IV), Se(VI), selenomethionine, Sb(III), Sb(V) and Te(VI). Speciation analysis was performed by on-line coupling of anion exchange high-performance liquid chromatography (HPLC) with inductively coupled plasma mass spectrometry (ICP-MS). Best storage of aqueous mixtures of the examined species was achieved at 3 C whereas at -20 C species transformation especially of selenomethionine and Sb(V) took place and a new selenium species appeared within a period of 30 days. Losses and species transformations during extraction processes were investigated. Extraction of the spiked fish material with methanol/water led to partial conversion of Sb(III), Sb(V) and selenomethionine to two new antimony and one new selenium species. The other arsenic, selenium and tellurium species were almost quantitatively extracted. For soil spiked with MMA, PAA, Se(IV) and Sb(III), recoveries after extraction with water and sulfuric acid (0.01 mol/L) were below 20%. (orig.)

  4. Antimony(v) cations for the selective catalytic transformation of aldehydes into symmetric ethers, α,β-unsaturated aldehydes, and 1,3,5-trioxanes.

    Science.gov (United States)

    Arias Ugarte, Renzo; Devarajan, Deepa; Mushinski, Ryan M; Hudnall, Todd W

    2016-07-01

    1-Diphenylphosphinonaphthyl-8-triphenylstibonium triflate ([][OTf]) was prepared in excellent yield by treating 1-lithio-8-diphenylphosphinonaphthalene with dibromotriphenylstiborane followed by halide abstraction with AgOTf. This antimony(v) cation was found to be stable toward oxygen and water, and exhibited exceptional Lewis acidity. The Lewis acidity of [][OTf] was exploited in the catalytic reductive coupling of a variety of aldehydes into symmetric ethers of type in good to excellent yields under mild conditions using Et3SiH as the reductant. Additionally, [][OTf] was found to selectively catalyze the Aldol condensation reaction to afford α-β unsaturated aldehydes () when aldehydes with 2 α-hydrogen atoms were used. Finally, [][OTf] catalyzed the cyclotrimerization of aliphatic and aromatic aldehydes to afford the industrially-useful 1,3,5 trioxanes () in good yields, and with great selectivity. This phosphine-stibonium motif represents one of the first catalytic systems of its kind that is able to catalyze these reactions with aldehydes in a controlled, efficient manner. The mechanism of these processes has been explored both experimentally and theoretically. In all cases the Lewis acidic nature of the antimony(v) cation was found to promote these reactions. PMID:27326797

  5. Annealing effects on structural, electrical and optical properties of antimony-tinoxide thin films deposited by sol gel dip coating technique

    Energy Technology Data Exchange (ETDEWEB)

    Lekshmy, S. Sujatha, E-mail: jolly2jolly@gmail.com; Anitha, V. S., E-mail: jolly2jolly@gmail.com; Berlin, I. John, E-mail: jolly2jolly@gmail.com; Joy, K., E-mail: jolly2jolly@gmail.com [Thin film Laboratory, Post Graduate and Research Department of Physics, Mar Ivanios College, Thiruvananthapuram 695 015 (India)

    2014-01-28

    Antimony-doped tin dioxide possess interesting physical and chemical properties. These properties have a wide range of applications such as catalysis and optoelectronic devices. In the present study, antimony-doped tin oxide (SnO2:Sb) thin films were deposited on the quartz substrates by sol-gel dip coating technique. The films were annealed at temperatures 350°C, 550°C and 850°C in air for 2 hours. The structure and surface morphologies were observed by X-ray diffraction (XRD) and Scanning electron microscopy (SEM). XRD patterns shows tetragonal structure for the SnO2:Sb films annealed at different temperatures. Crystallite size increased from 6 to 14 nm as annealing temperature increased from 350°C to 850°C. SEM studies reveals crack free and smooth surface for all the films. The grains are found to be homogenously distributed for films annealed at higher temperature. The electrical conductivity of the films annealed at 350°C and 550°C decreased and increased for the films annealed at 850°C. The optical properties of the films were investigated in the UV-visible-NIR region (200-900 nm) using UV spectra. The transmittance of the films decreased for films annealed at higher temperature. The optical energy band gap values (4.13 eV-4.83 eV) increased with the increase in annealing temperature.

  6. Oral bioavailability of arsenic, antimony and a selection of metals in ashes; Oral biotillgaenglighet av arsenik, antimon och ett urval av metaller i askor

    Energy Technology Data Exchange (ETDEWEB)

    Carlsson, Christel; Bendz, David; Jones, Celia

    2008-06-15

    In an earlier study, financed by Varmeforsk, 'Q4-238 Environmental guidelines for reuse of ash in civil engineering applications', the total content of arsenic and lead was shown to determine whether or not reuse of some of the ashes in construction work is feasible. The model used to calculate the guidelines uses the total concentration of metals to evaluate the health risks resulting from exposure to the ashes. The use of total concentration can lead to overly conservative risk assessments if a significant fraction of the total metal content is not bioavailable. Better precision in the risk assessment can be given by the use of the bioavailable fraction of arsenic and lead in the model. As a result, ashes which are rejected on the basis of total metal concentration may be acceptable for use in engineering construction when the assessment is based on the bioavailable fraction. The purpose of the study was to (i) compile information on the oral bioavailability of arsenic, antimony and a selection of metals in ashes and similar materials, and on in vitro methods for determination of oral bioavailability, and (ii) experimentally estimate oral bioavailability of arsenic, antimony and some metals in a selection of ashes by analysis of the gastrointestinal bioaccessibility of these elements. The investigated elements were antimony, arsenic, lead, cadmium, copper, chromium, nickel and zinc. In the literature study performed within the project a number of static and dynamic in vitro methods simulating gastrointestinal processes of contaminants were compiled. The methods include one or several segments, i.e. mouth, stomach and intestine. Among the compiled methods, the RIVM (Rijksinstituut voor volksgesundheid en milieu) in vitro method was used in the experimental part of the project. The advantages with the method was that: the method to a high degree mimicked the human gastrointestinal processes (the method included three segments mouth, stomach, and intestine

  7. Investigation on spread and risk factors of tuberculosis in antimony miners%锑矿工结核病传播及危险因素调查

    Institute of Scientific and Technical Information of China (English)

    陈开森; 刘涛; 林瑞瑞; 罗涛; 杨崇广

    2015-01-01

    Objective To explore the infection rate of tuberculosis ( TB) and its risk factors in antimony miners .Methods With cluster sampling method , the strains identification and drug sensitive test were performed in Mycobacterium tuberculosis ( MTB) of 263 TB patients in antimony miners .The method of 12 sites mycobacterial interspersed repetitive unit and variable number of tandem repeat wre used to determine the genetic type of MTB .Risk factors of TB spread were assessed by chi-square test.Results The TB infection rate in antimony miners was 9.8%(472/4 831);among 263 TB cases, 175 cases were found clustered the clustering rate was 66.5%, the least estimated recent TB spread rate was 53.2%.High TB spread rate was found in the antimony miners with failed treatment , length of service longer than 10 years , multidrug-resistant bacterial strains , and positive sputum smear .Conclusion The MTB of antimony miners showed the clustering feature and the bacterial strains had strong toxicity and higher spreading rate .The major risk factors affecting TB spread were therapeutic effect , length of service , drug resistant bacterial strain and sputum smear result .%目的 了解锑矿工肺结核感染率及感染的危险因素. 方法 采用整群抽样方法,对263例锑矿工肺结核患者进行结核分枝杆菌的菌株鉴定和药敏试验. 基因分型采用12位点结核分枝杆菌散在分布重复单元和多位点串联重复序列;采用X2检验评估结核传播的危险因素. 结果 锑矿工肺结核的感染率为9.8%(472/4 831); 纳入研究的263例患者中,175例成簇,成簇率为66 .5%,近期传播率最低估计值为53 .2%. 治疗失败、工龄大于10年、菌株多重耐药及痰涂片阳性的锑矿工肺结核传播率较高. 结论 锑矿工结核分枝杆菌具有成簇性,其菌株毒力更强、传播率高,治疗效果、矿龄、菌株耐药性及痰涂片结果是影响肺结核传播的重要危险因素.

  8. Oral bioavailability of arsenic, antimony and a selection of metals in ashes; Oral biotillgaenglighet av arsenik, antimon och ett urval av metaller i askor

    Energy Technology Data Exchange (ETDEWEB)

    Carlsson, Christel; Bendz, David; Jones, Celia

    2008-06-15

    In an earlier study, financed by Varmeforsk, 'Q4-238 Environmental guidelines for reuse of ash in civil engineering applications', the total content of arsenic and lead was shown to determine whether or not reuse of some of the ashes in construction work is feasible. The model used to calculate the guidelines uses the total concentration of metals to evaluate the health risks resulting from exposure to the ashes. The use of total concentration can lead to overly conservative risk assessments if a significant fraction of the total metal content is not bioavailable. Better precision in the risk assessment can be given by the use of the bioavailable fraction of arsenic and lead in the model. As a result, ashes which are rejected on the basis of total metal concentration may be acceptable for use in engineering construction when the assessment is based on the bioavailable fraction. The purpose of the study was to (i) compile information on the oral bioavailability of arsenic, antimony and a selection of metals in ashes and similar materials, and on in vitro methods for determination of oral bioavailability, and (ii) experimentally estimate oral bioavailability of arsenic, antimony and some metals in a selection of ashes by analysis of the gastrointestinal bioaccessibility of these elements. The investigated elements were antimony, arsenic, lead, cadmium, copper, chromium, nickel and zinc. In the literature study performed within the project a number of static and dynamic in vitro methods simulating gastrointestinal processes of contaminants were compiled. The methods include one or several segments, i.e. mouth, stomach and intestine. Among the compiled methods, the RIVM (Rijksinstituut voor volksgesundheid en milieu) in vitro method was used in the experimental part of the project. The advantages with the method was that: the method to a high degree mimicked the human gastrointestinal processes (the method included three segments mouth, stomach, and intestine

  9. Arsenic and Antimony Removal from Drinking Water by Point-of-Entry Reverse Osmosis Coupled with Dual Plumbing Distribution - U.S. EPA Demonstration Project at Carmel Elementary School in Carmel, ME -Final Performance Evaluation Report

    Science.gov (United States)

    This report documents the activities performed for and the results obtained from the arsenic and antimony removal treatment technology demonstration project at the Carmel Elementary School (CES) in Carmel, ME. An innovative approach of employing point of entry (POE) reverse osmo...

  10. Complex Beauty

    OpenAIRE

    Franceschet, Massimo

    2014-01-01

    Complex systems and their underlying convoluted networks are ubiquitous, all we need is an eye for them. They pose problems of organized complexity which cannot be approached with a reductionist method. Complexity science and its emergent sister network science both come to grips with the inherent complexity of complex systems with an holistic strategy. The relevance of complexity, however, transcends the sciences. Complex systems and networks are the focal point of a philosophical, cultural ...

  11. An evaluation of the migration of antimony from polyethylene terephthalate (PET) plastic used for bottled drinking water.

    Science.gov (United States)

    Chapa-Martínez, C A; Hinojosa-Reyes, L; Hernández-Ramírez, A; Ruiz-Ruiz, E; Maya-Treviño, L; Guzmán-Mar, J L

    2016-09-15

    The leaching of antimony (Sb) from polyethylene terephthalate (PET) bottling material was assessed in twelve brands of bottled water purchased in Mexican supermarkets by atomic fluorescence spectrometry with a hydride generation system (HG-AFS). Dowex® 1X8-100 ion-exchange resin was used to preconcentrate trace amounts of Sb in water samples. Migration experiments from the PET bottle material were performed in water according to the following storage conditions: 1) temperature (25 and 75°C), 2) pH (3 and 7) and 3) exposure time (5 and 15days), using ultrapure water as a simulant for liquid foods. The test conditions were studied by a 2(3) factorial experimental design. The Sb concentration measured in the PET packaging materials varied between 73.0 and 111.3mg/kg. The Sb concentration (0.28-2.30μg/L) in all of the PET bottled drinking water samples examined at the initial stage of the study was below the maximum contaminant level of 5μg/L prescribed by European Union (EU) regulations. The parameters studied (pH, temperature, and storage time) significantly affected the release of Sb, with temperature having the highest positive significant effect within the studied experimental domain. The highest Sb concentration leached from PET containers was in water samples at pH7 stored at 75°C for a period of 5days. The extent of Sb leaching from the PET ingredients for different brands of drinking water can differ by as much as one order of magnitude in experiments conducted under the worst-case conditions. The chronic daily intake (CDI) caused by the release of Sb in one brand exceeded the Environmental Protection Agency (USEPA) regulated CDI value of 400ng/kg/day, with values of 514.3 and 566.2ng/kg/day for adults and children. Thus, the appropriate selection of the polymer used for the production of PET bottles seems to ensure low Sb levels in water samples. PMID:27192700

  12. Synthesis and structure of iridium complex [pH 4Sb(DMSO)] +[IrCl 4(DMSO) 2] -

    OpenAIRE

    SHARUTIN V.V.; SHARUTINA O.K.; Senchurin, V. S.

    2015-01-01

    Iridium complex [Ph 4Sb(DMSO)] +[IrCl 4(DMSO) 2] (1) has been synthesized by interaction of tetraphenylstibonium chloride with sodium hexachloroiridate(III) in water. From X-ray diffraction analysis data, two types of crystallographically independent cations [Ph 4Sb(DMSO)] + and anions [IrCl 4(DMSO) 2] exist in the crystal. The antimony atoms in cations have distorted trigonal-bipyramidal surroundings with O-dimethyl sulphoxide ligand in axial position (equatorial angles CSbC 113.6(2)°-121.2(...

  13. Metal complexes with 2-acetylpyridine-N(4)-orthochlorophenylthiosemicarbazone: cytotoxicity and effect on the enzymatic activity of thioredoxin reductase and glutathione reductase.

    Science.gov (United States)

    Parrilha, Gabrieli L; Ferraz, Karina S O; Lessa, Josane A; de Oliveira, Kely Navakoski; Rodrigues, Bernardo L; Ramos, Jonas P; Souza-Fagundes, Elaine M; Ott, Ingo; Beraldo, Heloisa

    2014-09-12

    Metal complexes with 2-acetylpyridine-N(4)-orthochlorophenylthiosemicarbazone (H2Ac4oClPh) were assayed for their cytotoxicity against MCF-7 breast adenocarcinoma and HT-29 colon carcinoma cells. The thiosemicarbazone and most of the complexes were highly cytotoxic. H2Ac4oClPh and its gallium(III) and tin(IV) complexes did not show any inhibitory activity against thioredoxin reductase (TrxR) and glutathione reductase (GR). The palladium(II), platinum(II) and bismuth(III) complexes inhibited TrxR at micromolar concentrations but not GR. The antimony(III) and gold(III) complexes strongly inhibited TrxR at submicromolar doses with GR inhibition at higher concentrations. The selectivity of these complexes for TrxR suggests metal binding to a selenol residue in the active site of the enzyme. TrxR inhibition is likely a contributing factor to the mode of action of the gold and antimony derivatives. PMID:25058344

  14. Research on the Flotation of a Gold - antimony Ore in Gansu%甘肃某金锑矿选矿试验研究

    Institute of Scientific and Technical Information of China (English)

    吉庆军

    2012-01-01

    The systematical flotation experiments were conducted on a gold - antimony ore in Gansu based on mineralogy. When the grinding fineness was 82% -0. 074 mm, sodium silicate was used as ganguefe depressant, lead nitrate as activator, and the mixture of sodium ethyl xanthate and ammonium dibutyl dithiophosphate as selective flotation collectors, an antimony concentrate of 50. 67% Sb could be obtained with a recovery of 78.43% . Then the mixture of sodium sulfide and copper sulfate were used as activators of gold - bearing mineral in antimony tailings, combined collectors was also used, and benzyl hydroxamic acid was used to enhance gold flotation. A gold concentrate containing 60. 89 g/t Au could be obtained with a recovery of 80. 52% .%以甘肃某金锑矿为研究对象,在矿石工艺矿物学研究的基础上,通过系统的浮选试验,对含锑0.73%、金2.42 g/t的原矿,确定在磨矿细度为-0.074 mm占82%时,采用单一的水玻璃作为脉石矿物抑制剂,以硝酸铅活化含锑矿物,混合使用乙基黄药和丁铵黑药优先浮选锑,组合采用硫化钠与硫酸铜活化浮锑尾矿中的载金矿物,混合使用Y89黄药和丁铵黑药浮金,浮金回路添加少量苯甲羟肟酸以强化浮选效果,实验室小型闭路试验可获得锑精矿品位50.67%、回收率78.43%;金精矿含金60.89 g/t、回收率80.52%的选矿指标.

  15. Producing Cubic Crystal Antimony White from Arsenic-Containing Complex Dyscrasite%从复杂含砷锑银矿制取立方晶型锑白

    Institute of Scientific and Technical Information of China (English)

    聂晓军; 朱柒金; 陈庆邦

    2000-01-01

    通过对复杂含砷锑银矿制取锑白的研究,提出了采用HCl 体系,NaClO3为氧化剂酸性浸出的处理方法.在最佳工艺条件下进行浸出,Sb的浸出率大于95%,Ag的浸出率低于5%,As基本上留在浸出渣中.对浸出液采取预处理后,制取了白度大于94,符合国家0级标准的立方晶型锑白.

  16. 砷(Ⅲ)、锑(Ⅲ)配合物的固相合成%Synthesis of Arsenic(Ⅲ) and Antimony(Ⅲ) Complexes by Solid Phase Reaction

    Institute of Scientific and Technical Information of China (English)

    钟国清; 栾绍嵘; 陈娅如

    2002-01-01

    用固相反应法合成了碘化砷、氯化锑与硫脲(Tu)和半胱氨酸(Cys)的配合物,用元素分析、IR及X射线粉末衍射进行了表征. 配合物组成为:ML3X3(M=As、Sb,L=Cys、Tu,X=I、Cl),它们在空气中稳定,不吸湿,微溶于水. 几种配合物晶体结构均属单斜晶系,配合物As(Cys)3I3的晶胞参数为:a=1.174 3 nm,b=0.694 5 nm,c=1.682 2 nm,β=95.28°;As(Tu)3I3的晶胞参数为:a=1.111 9 nm,b=1.903 0 nm,c=1.541 0 nm,β=94.77°;Sb(Cys)3Cl3晶胞参数为:a=1.205 1 nm,b=0.679 2 nm,c=1.685 0 nm,β=95.79°;Sb(Tu)3Cl3的晶胞参数为:a=1.234 3 nm,b=1.658 5 nm,c=1.925 2 nm,β=96.46°.

  17. Biological Activities of the Complexes of Arsenic, Antimony and Bismuth%砷、锑、铋配合物的生物活性

    Institute of Scientific and Technical Information of China (English)

    张志朋; 钟国清; 蒋琪英

    2008-01-01

    合成新型砷、锑、铋的配合物并研究其构效关系与生物活性的作用机理,对于丰富生物无机化学内容、开发新的抗菌和治疗肿瘤的化学药物都具有重要的意义和价值.本文简要介绍了砷、锑、铋的化学性质,并综述了近年来砷、锑、铋的配合物在抗癌抗菌抗肿瘤等生物活性方面的应用,展望了其在该领域的应用前景.

  18. 黔西南一小型锑冶炼厂环境污染调查分析%Investigation and Analysis on Environmental Pollution Due to a Small Antimony Smeltery in Southwest Guizhou Province

    Institute of Scientific and Technical Information of China (English)

    张军营; 钟秦; 任德贻

    2001-01-01

    Objective To understand the impacts of a small antimony smeltery on surrounding environment. Methods The samples of raw materials,such as ore and coal,soil and plant around a small antimony smeltery in southwest Guizhou province were analyzed. Results The levels of arsenic,mercury,fluoride ,antimony and selenium in soil around the antimony smeltery significantly increased compared with the average background levels of related elements in nationwide range . The levels of arsenic, mercury,fluoride ,antimony and selenium in soil around the antimony smeltery were 1. 73~4.69,4. 75~237.5,2. 26~3.42,35.6~36. 2,54. 29~57.14 times as much as their related average levels in our country respectively. The levels of arsenic ,mercury ,fluoride and selenium in soil around the smeltery were 1.25~ 3. , 58,1.86~ 93.14,1.38~ 2.08,33. 04~ 34.78 times as much as their related average levels of Guizhou province respectively. The levels of arsenic, mercury, fluoride, antimony and selenium in corn leaves around the smeltery was 67,26.7,1046.4,2220,38. 8 times as much as their related average levels in non-polluted plants respectively. Conclusion The air pollutants,such as sulphur,arsenic,mercury,fluoride,antimony and selenium in industrial waste gas emitted from the antimony smeltery had resulted in heavy pollution to the environment, which was aggravated by the application of coal with high level of sulphur.%目的了解小型锑冶炼厂对周围环境的影响。方法对黔西南一小型锑冶炼厂矿石、燃用煤以及周围土壤和植物样品进行了分析。结果锑冶炼厂周围土壤中元素含量与全国土壤中元素平均含量比较,As、Hg、F、Sb、Se的含量明显偏高,As为1. 73~4.96倍,Hg为4.75~237.5倍,F为2.26~3.42倍,Sb为35.6~36.2倍,Se为54.29~57.14倍;也高于贵州土壤的平均含量,As为1. 25~3.58倍,Hg为1.86~93.14倍,F为1.38~2.08倍,Se为33.04~34.78倍。玉米叶片中As、Hg、F

  19. Post-CMOS FinFET integration of bismuth telluride and antimony telluride thin-film-based thermoelectric devices on SoI substrate

    KAUST Repository

    Aktakka, Ethem Erkan

    2013-10-01

    This letter reports, for the first time, heterogeneous integration of bismuth telluride (Bi2Te3) and antimony telluride (Sb 2Te3) thin-film-based thermoelectric ffect transistors) via a characterized TE-film coevaporationand shadow-mask patterning process using predeposition surface treatment methods for reduced TE-metal contact resistance. As a demonstration vehicle, a 2 × 2 mm2-sized integrated planar thermoelectric generator (TEG) is shown to harvest 0.7 μ W from 21-K temperature gradient. Transistor performance showed no significant change upon post-CMOS TEG integration, indicating, for the first time, the CMOS compatibility of the Bi2Te3 and Sb2Te3 thin films, which could be leveraged for realization of high-performance integrated micro-TE harvesters and coolers. © 2013 IEEE.

  20. Progress report on neutron beam experiments in Thailand: effects of antimony substitutions on the critical temperature of Bi-Pb-Sr-Ca-Cu-O compounds

    Energy Technology Data Exchange (ETDEWEB)

    Sangariyavanich, A.; Ampornrat, P. [Office of Atomic Energy for Peace, Bangkok (Thailand)

    1998-10-01

    Effects of systematic substitutions of antimony for bismuth in Bi{sub 1.8-x}Pb{sub 0.2}Sb{sub x}Sr{sub 2}Ca{sub 3}Cu{sub 4}O{sub 10} have been investigated. Fabrication of the specimens has been performed by solid state reaction in air. The samples were sintered between 820degC - 843degC for 65 hours and subsequently quenched in liquid nitrogen. The critical temperatures of most specimens as determined by standard four-probe technique was higher than 100 K. Phase identification by X-ray diffraction technique indicated that `2223` and `2234` were the predominant phases in these samples. (author)

  1. Behavior of antimony isotopes in the primary coolant of WWER-1000-type nuclear reactors in NPP Kozloduy during operation and shutdown

    Energy Technology Data Exchange (ETDEWEB)

    Dobrevski, Ivan D.; Zaharieva, Neli N. [Bulgarian Academy of Sciences, Sofia (Bulgaria). Inst. for Nuclear Research and Nuclear Energy; Minkova, Katia F.; Gerchev, Nikolay B. [Kozloduy Nuclear Power Plant, Kozloduy (Bulgaria). Dept. of Chemistry and Radiochemistry

    2009-05-15

    This paper focuses on the behavior of the antimony isotopes {sup 122}Sb and {sup 124}Sb in the coolant of the WWER reactors in the nuclear power plant Kozloduy (Bulgaria) during operation and shutdown. It is concluded that the chemical properties of their actual precursor, the isotope {sup 121}Sb, determine the behavior of {sup 122}Sb and {sup 124}Sb during operation, load fluctuations, and shutdown as well as during the reactor coolant purification process. It is supposed that differences between the reactor bulk and the core fuel cladding surface chemistry as well as the presence of sub-cooled nucleate boiling at the fuel cladding may create conditions under which a local oxidizing environment may come into existence. (orig.)

  2. Influence of mycorhization and soil organic matters on lead and antimony transfers to vegetables cultivated in urban gardens: environmental and sanitary consequences

    Science.gov (United States)

    Pierart, Antoine; Braud, Armelle; Lebeau, Thierry; Séjalon-Delmas, Nathalie; Dumat, Camille

    2014-05-01

    The European Environment Agency estimates that c.a. 250 000 sites required clean up and that about 100 000 ha could have been contaminated by metals in Europe. Numerous remediation techniques have been therefore tested and phytoremediation appears as a sustainable and low cost in situ technique particularly for large-scale remediation of polluted arable soils. Arbuscular Mycorrhizal Fungi (AMF) are already used in phytoextraction or phytostabilisation of many metal(loid)s (GU ET AL., 2013, SHARMA AND SHARMA, 2013). However, while plant inoculation with AMF will mostly result of an increase of the plant biomass, the response for lead accumulation in shoots is contrasted (LEBEAU ET AL., 2008). Furthermore, nothing is actually known for Sb transfer to plants phytoremediation-assisted AMF. Yet recently, many researches concern the accumulation of Sb in the environment, its (eco)toxicity and the risk of bioaccumulation in vegetables (FENG ET AL., 2013), especially in some China areas where Sb mining activities have widely contaminated arable lands (WU ET AL., 2011). Our research project, which is part of a national program for urban gardens (JASSUR, http://www.agence-nationale-recherche.fr), focused on polluted soils in associative urban gardens with both geogenic and anthropogenic origins for Pb and Sb. The impact of Pb and Sb on AMF density and diversity was studied using morphological and biomolecular approaches. The role of AMF symbiosis with Lettuce (Lactuca sativa L.) on Pb and Sb compartmentalization, speciation and phytoavailability was investigated. The influence of soil organic matters on these processes was examined. Eventually, the part of metal(loid)s available for humans in case of ingestion of lettuces unfit for human consumption (FOUCAULT ET AL., 2013; XIONG ET AL., 2013) will be assessed in relation with the influence of AMF symbiosis and organic matter. Key Words: Mycorrhiza, Antimony, Compartmentation, Speciation, Edible Plants, Urban Agriculture

  3. Bucolic Complexes

    CERN Document Server

    Brešar, Bostjan; Chepoi, Victor; Gologranc, Tanja; Osajda, Damian

    2012-01-01

    In this article, we introduce and investigate bucolic complexes, a common generalization of systolic complexes and of CAT(0) cubical complexes. This class of complexes is closed under Cartesian products and amalgamations over some convex subcomplexes. We study various approaches to bucolic complexes: from graph-theoretic and topological viewpoints, as well as from the point of view of geometric group theory. Bucolic complexes can be defined as locally-finite simply connected prism complexes satisfying some local combinatorial conditions. We show that bucolic complexes are contractible, and satisfy some nonpositive-curvature-like properties. In particular, we prove a version of the Cartan-Hadamard theorem, the fixed point theorem for finite group actions, and establish some results on groups acting geometrically on such complexes. We also characterize the 1-skeletons (which we call bucolic graphs) and the 2-skeletons of bucolic complexes. In particular, we prove that bucolic graphs are precisely retracts of Ca...

  4. Comparison of the native antimony-bearing Paiting gold deposit, Guizhou Province, China, with Carlin-type gold deposits, Nevada, USA

    Science.gov (United States)

    Xie, Zhuo-Jun; Xia, Yong; Cline, Jean S.; Yan, Bao-Wen; Wang, Ze-Peng; Tan, Qin-Ping; Wei, Dong-Tian

    2016-03-01

    The Paiting gold deposit, Guizhou Province, China, has been regarded as a Carlin-type gold deposit by several researchers. Alteration and ore-related minerals from the Paiting deposit were examined, and results were compared with the Cortez Hills Carlin-type gold deposit, Nevada, USA. Similarities include the structural and stratigraphic controls on the orebodies in both deposits and the occurrence of invisible gold ionically bound in arsenian pyrite. Significant differences include the following: (1) The gold-bearing mineral in Nevada is arsenian pyrite. However, gold-bearing minerals in the Paiting deposit include arsenopyrite, arsenian pyrite, and trace pyrrhotite. Also, euhedral or subhedral gold-bearing arsenian pyrite at Paiting contains significantly less As, Cu, and Hg than gold-bearing pyrite from Nevada. (2) Alteration in the Paiting deposit displays significantly less decarbonatization. Instead, dolomite precipitation, which has not been described in Nevada deposits, is associated with deposition of gold-bearing sulfide minerals. (3) Stibnite and minor native antimony typify Paiting late-ore-stage minerals, whereas in Nevada, realgar, orpiment, and calcite are common late-ore-stage minerals. Precipitation of native antimony in the Paiting deposit reflects the evolution of a late-ore fluid with unusually low sulfur and oxygen fugacities. Some characteristics of the Paiting gold deposit, including formation of ore-stage dolomite and precipitation from CO2-rich ore fluids at temperatures in excess of 250 °C, are more typical of orogenic deposits than Nevada Carlin deposits. The presence of similarities in the Paiting deposit to both Carlin type and orogenic deposits is consistent with formation conditions intermediate to those typical of Carlin type and orogenic systems.

  5. Study on Cobalt Removal with Antimony Trioxide in Zinc Hydrometallurgy%湿法炼锌锑盐除钴工艺的研究

    Institute of Scientific and Technical Information of China (English)

    姜艳; 谢刚; 肖锐敏; 李自静; 孙丽达; 黄笃树

    2013-01-01

    采用三氧化二锑对湿法炼锌的硫酸锌溶液进行净化除钴.考察锌粉用量、三氧化二锑用量、锌粉粒度、搅拌速度、温度、时间等对净化除钴效果的影响.结果表明,细粒度锌粉和强烈搅拌除钴效果较好,在合适的温度和时间下也能达到净化要求.最优除钴工艺条件为:三氧化二锑3 mg/L,锌粉2 g/L,锌粉粒度0.074~0.050 mm,搅拌转速300 r/min,温度85℃和时间90 min.%Cobalt in zinc sulfate solution from zinc hydrometallurgy was purified with antimony trioxide.The effects of dosage of zinc powder and antimony trioxide,particle size of zinc powder,stirring rate,temperature,and time on cobalt removal were examined.The results show that good cobalt removal effect can be achieved with fine-grained zinc powder by strong mixing and purification requirements can be met in appropriate temperature and time.The optimum conditions for cobalt removal include dosage of Sb2O3 of 3 mg/L,dosage of zinc powder of 2 g/L,zinc powder particle size of 0.074~0.050 mm,stirring rate of 300 r/min,temperature of 85 C and time of 90 min.

  6. Association of liposome-encapsulated trivalent antimonial with ascorbic acid: an effective and safe strategy in the treatment of experimental visceral leishmaniasis.

    Directory of Open Access Journals (Sweden)

    Renata A O Castro

    Full Text Available BACKGROUND: Visceral leishmaniasis (VL is a chronic debilitating disease endemic in tropical and subtropical areas, caused by protozoan parasites of the genus Leishmania. Annually, it is estimated the occurrence of 0.2 to 0.4 million new cases of the disease worldwide. Considering the lack of an effective vaccine the afflicted population must rely on both, an accurate diagnosis and successful treatment to combat the disease. Here we propose to evaluate the efficacy of trivalent antimonial encapsulated in conventional liposomes, in association with ascorbic acid, by monitoring its toxicity and efficacy in BALB/c mice infected with Leishmania infantum. METHODOLOGY/PRINCIPAL FINDINGS: Infected mice were subjected to single-dose treatments consisting in the administration of either free or liposome-encapsulated trivalent antimony (SbIII, in association or not with ascorbic acid. Parasite burden was assessed in the liver, spleen and bone marrow using the serial limiting dilution technique. After treatment, tissue alterations were examined by histopathology of liver, heart and kidney and confirmed by serum levels of classic biomarkers. The phenotypic profile of splenocytes was also investigated by flow cytometry. Treatment with liposome-encapsulated SbIII significantly reduced the parasite burden in the liver, spleen and bone marrow. Co-administration of ascorbic acid, with either free SbIII or its liposomal form, did not interfere with its leishmanicidal activity and promoted reduced toxicity particularly to the kidney and liver tissues. CONCLUSIONS/SIGNIFICANCE: Among the evaluated posological regimens treatment of L. infantum-infected mice with liposomal SbIII, in association with ascorbic acid, represented the best alternative as judged by its high leishmanicidal activity and absence of detectable toxic effects. Of particular importance, reduction of parasite burden in the bone marrow attested to the ability of SbIII-carrying liposomes to

  7. Investigation of strontium and uranium sorption onto zirconium-antimony oxide/polyacrylonitrile (Zr-Sb oxide/PAN) composite using experimental design.

    Science.gov (United States)

    Cakir, Pelin; Inan, Suleyman; Altas, Yuksel

    2014-04-30

    A study on the sorption of strontium (Sr(2+)) and uranium (UO2(2+)) onto zirconium-antimony oxide/PAN (Zr-Sb oxide/PAN) composite was conducted. The zirconium-antimony oxide was synthesized and was then turned into composite spheres by mixing it with polyacrylonitrile (PAN). The single and combined effects of independent variables such as initial pH, temperature, initial ion concentration and contact time on the sorption of Sr(2+) and UO2(2+) were separately analyzed using response surface methodology (RSM). Central composite design (CCD) was separately employed for Sr(2+) and UO2(2+) sorption. Analysis of variance (ANOVA) revealed that all of the single effects found statistically significant on the sorption of Sr(2+) and UO2(2+). Probability F-values (F=2.45 × 10(-08) and F=9.63 × 10(-12) for Sr(2+) and UO2(2+), respectively) and correlation coefficients (R(2)=0.96 for Sr(2+) and R(2)=0.98 for UO2(2+)) indicate that both models fit the experimental data well. At optimum sorption conditions Sr(2+) and UO2(2+) sorption capacities of the composite were found as 39.78 and 60.66 mg/g, respectively. Sorption isotherm data pointed out that Langmuir model is more suitable for the Sr(2+) sorption, whereas the sorption of UO2(2+) was correlated well with the Langmuir and Freundlich models. Thermodynamic parameters such as ΔH°, ΔS° and ΔG° indicate that Sr(2+) and UO2(2+) sorption processes are endothermic and spontaneous. PMID:24632364

  8. Geomicrobiological cycling of antimony

    Science.gov (United States)

    Kulp, T. R.; Terry, L.; Dovick, M. A.; Braiotta, F.

    2013-12-01

    Microbiologically catalyzed oxidation and reduction of toxic metalloids (e.g., As, Se, and Te) generally proceeds much faster than corresponding abiotic reactions. These microbial transformations constitute biogeochemical cycles that control chemical speciation and environmental behavior of metalloids in aqueous environments. Particular progress has been made over the past two decades in documenting microbiological biotransformations of As, which include anaerobic respiratory reduction of As(V) to As(III), oxidation of As(III) to As(V) linked to chemoautotrophy or photoautotrophy, and cellular detoxification pathways. By contrast, microbial interactions with Sb, As's group 15 neighbor and a toxic element of emerging global concern, are poorly understood. Our work with sediment microcosms, enrichment cultures, and bacterial isolates suggests that prokaryotic metabolisms may be similarly important to environmental Sb cycling. Enrichment cultures and isolates from a Sb-contaminated mine site in Idaho exhibited Sb(V)-dependent heterotrophic respiration under anaerobic conditions and Sb(III)-dependent autotrophic growth in the presence of air. Live, anoxic cultures reduced 2 mM Sb(V) to Sb(III) within 5 d, while no activity occurred in killed controls. Sb(V) reduction was stimulated by lactate or acetate and was quantitatively coupled to the oxidation of lactate. The oxidation of radiolabeled 14C-acetate (monitored by GC-GPC) demonstrated Sb(V)-dependent oxidation to 14CO2, suggesting a dissimilatory process. Sb(V) dependent growth in cultures was demonstrated by direct counting. Microbiological reduction of Sb(V) also occurred in anerobic sediment microcosms from an uncontaminated suburban lake, but did not appear to be linked to growth and is interpreted as a mechanism of biological detoxification. Aerobic microcosms and cultures from the Idaho mine oxidized 2 mM Sb(III) to Sb(V) within 7 d and coupled this reaction to cell growth quantified by direct counting. An anoxygenic photosynthetic community of purple sulfur bacteria from Pyramid Lake, NV, however, that was capable of growth via anoxygenic photosynthesis using As(III) as an electron donor was not capable of similar growth using Sb(III). These results suggest that geomicrobiological Sb cycling is an important influence on the environmental speciation and behavior of Sb, and portend the presence of a global biogeochemical Sb cycle that is analogous to but distinct from that for As.

  9. 水、土环境中锑污染与控制研究进展%Research progress on present situation and countermeasure of antimony pollution in water and soil environment

    Institute of Scientific and Technical Information of China (English)

    张亚平; 张婷; 陈锦芳; 彭然

    2011-01-01

    随着工业的发展,锑作为一种具有潜在毒性和致癌性的类金属元素,已经较为广泛地存在于水体和土壤环境中,显现出不可忽视的环境问题,并引起国际科学界的高度关注.文章综述了锑在水体和土壤环境中的污染现状、化学行为形态以及污染控制方面的研究进展.由采矿业、制造业带来的锑水土污染问题较为突出,目前的处理处置方法难以满足需求.今后需要在锑的水土环境化学方面加强研究,探讨锑的迁移转化规律;高效吸附材料的开发制备也是一个重要内容;植物组合修复土壤中的锑污染将是一个重要的突破口.%Antimony exists widely in water and soil environment with the development of industry. It has brought out noticeable environment problems, and has drawn quite a lot of attentions from scientists, as a metalloid element with potentially toxicity and carcinogenicity. Current pollution status, species and biogeochemical behaviour of antimony in water and soil, and research on the contamination control were viewed in this paper. Pollution of antimony in water and soil caused by mining and manufacturing has become increasingly seriously, and the methods to deal with it can hardly meet the demands. As a result, some works as follows need to be done: research in the environmental chemistry of antimony in water and soil should be strengthened in the future, as well as exploring the principle of antimony in movement and transformation. Development and preparation of new materials with efficient adsorbability are also important. Moreover, phytoremediation combination technology to remedy pollution of antimony in soil may be another important breakthrough.

  10. Determination of arsenic in antimony ingot and antimony trioxide by hydride generation-atomic fluorescence spectrometry%氢化物发生-原子荧光光谱法测定锑锭及三氧化二锑中的砷

    Institute of Scientific and Technical Information of China (English)

    钱光敏; 赵国杏

    2012-01-01

    The antimony slab and antimonous oxide samples were dissolved by sulfuric acid and hydrochloric acid, respectively. The Sb3+ in solution was precipitated with sodium hydroxide to separate trace arsenic from matrix antimony. The thiourea-ascorbic acid was added to reduce As5+ to As3+. Then, the arsenic in antimony slab and antimonous oxide was determined by atomic fluorescence spec-trometry. The hydride generation conditions were investigated: the concentration of reducing agent potassium borohydride was 25 g/L, the determination medium was 20% (V/V) hydrochloric acid, and the dosage of thiourea - ascorbic acid solution was 5 mL. The interference test of coexisting elements showed that, the interference of residual antimony in solution after precipitation could be fully eliminated by adding 1 mL of tartaric acid solution. Other impurity elements in sample did not interfere with the determination of arsenic after adding thiourea-ascorbic acid solution. The detection limit of method was 0. 156 ng/mL. The antimony slab and antimonous oxide samples were analyzed by the proposed method, and the relative standard deviation (RSD) was 0. 95%-1.2%. The determination results were consistent with those obtained by national standard methods.%采用硫酸溶解锑锭样品,盐酸溶解三氧化二锑样品,用氢氧化钠溶液使Sb3+沉淀从而使基体锑与微量砷分离,通过加入硫脲-抗坏血酸将As5+还原成As3+,然后在原子荧光仪上测定锑锭及三氧化二锑中的砷.对氢化物发生条件进行考察,确定还原剂硼氢化钾的浓度为25 g/L、测定介质为20%(V/V)盐酸、硫脲-抗坏血酸溶液用量为5 mL.共存元素干扰试验表明,沉淀后溶液中残留少量锑的干扰在加入1 mL酒石酸溶液后可以完全消除,而样品中其他杂质元素在加入硫脲-抗坏血酸溶液后不干扰砷的测定.方法的检出限为0.156 ng/mL.对锑锭及三氧化二锑样品进行分析,相对标准偏差为0.95%~1.2%,测定

  11. Tetra-Antimony(III)-Bridged 18-Tungsto-2-Arsenates(V), [(LSb(III))4(A-α-As(V)W9O34)2](10-) (L = Ph, OH): Turning Bioactivity On and Off by Ligand Substitution.

    Science.gov (United States)

    Yang, Peng; Lin, Zhengguo; Bassil, Bassem S; Alfaro-Espinoza, Gabriela; Ullrich, Matthias S; Li, Ming-Xing; Silvestru, Cristian; Kortz, Ulrich

    2016-04-18

    Two tetra-antimony(III)-bridged, sandwich-type 18-tungsto-2-arsenates(V), [(LSb(III))4(A-α-As(V)W9O34)2](10-) (L = Ph (1), OH (2)), were prepared and fully characterized in the solid state and in solution. Both polyanions are stable in aqueous physiological medium for at least 24 h (at concentrations ≥2.5 × 10(-6) M). Despite the presence of an isostructural tetra-antimony(III) motif in 1 and 2, distinctly different antibacterial activity was observed for both polyanions. The minimum inhibitory concentrations (MIC) of 1 (7.8-62.5 μg/mL) is lower than for any other organoantimony(III)-containing polyoxometalate reported to date.

  12. Tetra-Antimony(III)-Bridged 18-Tungsto-2-Arsenates(V), [(LSb(III))4(A-α-As(V)W9O34)2](10-) (L = Ph, OH): Turning Bioactivity On and Off by Ligand Substitution.

    Science.gov (United States)

    Yang, Peng; Lin, Zhengguo; Bassil, Bassem S; Alfaro-Espinoza, Gabriela; Ullrich, Matthias S; Li, Ming-Xing; Silvestru, Cristian; Kortz, Ulrich

    2016-04-18

    Two tetra-antimony(III)-bridged, sandwich-type 18-tungsto-2-arsenates(V), [(LSb(III))4(A-α-As(V)W9O34)2](10-) (L = Ph (1), OH (2)), were prepared and fully characterized in the solid state and in solution. Both polyanions are stable in aqueous physiological medium for at least 24 h (at concentrations ≥2.5 × 10(-6) M). Despite the presence of an isostructural tetra-antimony(III) motif in 1 and 2, distinctly different antibacterial activity was observed for both polyanions. The minimum inhibitory concentrations (MIC) of 1 (7.8-62.5 μg/mL) is lower than for any other organoantimony(III)-containing polyoxometalate reported to date. PMID:27043954

  13. Use of tetracycline as complexing agent in radiochemical separations

    International Nuclear Information System (INIS)

    The use of the antibiotic agent tetracycline (TC) for analytical purposes in solvent extraction procedures is presented. Individual extraction curves for the lanthanides, zinc, scandium, uranium, thorium, neptunium and protactinium were obtained. Separation of those elements from one another, and of uranium from selenium, bromine, antimony, barium, tantalum and tungsten was carried out. In all cases benzyl alcohol was the diluent used to dissolve tetracycline hydrochloride. Sodium chloride was used as supporting electrolyte for the lanthanide separations and sodium perchlorate for the other elements mentioned. Stability or formation constants for the lanthanide complexes as well as for thorium complex with tetracycline were determined by using the methods of average number of ligands, the limiting value (for thorium), the two parameters and the weighted least squares. For the lanthanides, the stability constants of the complexes Ln(TC)3 go from 9.35+-0.22 for lanthanum up to 10.84+-0.11 for lutetium. For the Th(TC)4 complex the formation constant is equal to 24.6+-0.3. Radioisotopes of the respective elements were used as tracers for the determinations. (author)

  14. 氢化物发生-原子荧光光谱法测定合金钢及合金中痕量元素铅、锡、砷、锑、铋的进展%Determination Progress of Trace Elements (Lead, Tin, Arsenic, Antimony, Bismuth)in Staliness Steel Alloys by HF-AFS

    Institute of Scientific and Technical Information of China (English)

    赵艳兵; 刘爱坤; 戴学谦; 王珺

    2011-01-01

    通过对近年来有关氢化物发生-原子荧光光谱法在复杂基体体系中痕量元素检测方面的资料总结,阐述了氢化物发生-原子荧光光谱法分析过程中的干扰类型、干扰机理及消除干扰的措施,对其在合金钢及合金中痕量元素铅、锡、砷、锑、铋测定中的应用进展作了评述,并对氢化物发生-原子荧光光谱法的发展前景提出了展望。%This paper presented a data summary of determination of trace elements in a complex matrix system by HG-AFS,covering the recent years. The interference type, interference mechanism and measures to eliminate interference of HG-AFS were also described. We reviewed the progress of the determination application of the Staliness Steel Alloys of trace elements, tin, lead, arsenic, antimony bismuth.We also discussed the HG-AFS development prospect.

  15. Normal coordinate analysis and quantum chemical study of tris(-fluorophenyl)antimony di(-phenylglycinate) [(-FC6H4)3Sb(O2CCH2NHC6H5)2

    Indian Academy of Sciences (India)

    Tanveer Hasan; P K Singh; K Singhal; P Raj; Neeraj Misra

    2007-10-01

    A complete normal coordinate analysis was performed by two different methods: a classical Wilson's G-F matrix method and the semi-empirical molecular orbital PM3 method, for a five coordinate tris(-fluorophenyl)antimony di( -phenylglycinate) [(-FC6H4)3Sb(O2CCH2NHC6H5)2], known to be an in vitro antitumour molecule.

  16. Structural consideration of antimony pentafluoride deposited on metal oxides (SiO2, Al2O3, and SiO2-Al2O3) by X-ray absorption (EXAFS/XANES) spectroscopy

    International Nuclear Information System (INIS)

    Using EXAFS/XANES, the structural environments of antimony pentafluoride deposited on SiO2, Al2O3, and SiO2-Al2O3 oxides are investigated to generate strong acid sites on the oxides. Sb-ligand bond lengths for SbF5 deposited on the oxides vary depending on the type of oxide. 31 refs., 6 figs., 2 tabs

  17. Combined effect of strontium modifier and antimony refiner on texture and growth mode of eutectic phase in an Al-11Si-2Cu-0.8Zn-0.6Fe cast alloy

    Science.gov (United States)

    Farahany, Saeed; Ourdjini, Ali; Hekmat-Ardakan, Alireza

    2015-12-01

    Results of electron back-scattered diffraction and transmission electron microscopy studies reveal that the orientation of aluminium in the eutectic phase is different from the surrounding aluminium dendrites and that twin spacing of eutectic silicon increased significantly due to the interaction between strontium and antimony. In addition, the formation of ternary Mg2Sb2Sr intermetallic compound that precedes the eutectic reaction was proposed to be responsible for interaction.

  18. The application of lead-antimony-rare earth alloy in the power batterys%低锑稀土合金在动力电池中的应用

    Institute of Scientific and Technical Information of China (English)

    郭志刚; 刘玉; 徐明学; 邓成智; 周文渭; 曹进; 李桂发

    2015-01-01

    本文针对目前市场上出现的一种新型铅锑稀土合金,从合金的成分、耐腐蚀性,电池初期性能及循环使用寿命等方面进行了研究。试验结果表明:该合金具有较好的耐腐蚀性能,对电池初期性能也不会带来明显的影响,但在循环使用过程中,会使电池失水严重,从而造成使用寿命缩短。%This paper mainly discussed a lead-antimony-rare earth alloy which was used as the grid material of lead-acid batteries. The chemical composition and corrosion resistance of the lead-antimony-rare earth alloy, and initial performance and cycle life of lead-acid batteries with the lead-antimony-rare earth alloy were studied. The experimental results showed that the alloy had a good corrosion resistance, and didn’t impact the initial performance of the battery. However, it would lead to a shortened service life of lead-acid batteries because of severe water loss.

  19. Complexity Plots

    KAUST Repository

    Thiyagalingam, Jeyarajan

    2013-06-01

    In this paper, we present a novel visualization technique for assisting the observation and analysis of algorithmic complexity. In comparison with conventional line graphs, this new technique is not sensitive to the units of measurement, allowing multivariate data series of different physical qualities (e.g., time, space and energy) to be juxtaposed together conveniently and consistently. It supports multivariate visualization as well as uncertainty visualization. It enables users to focus on algorithm categorization by complexity classes, while reducing visual impact caused by constants and algorithmic components that are insignificant to complexity analysis. It provides an effective means for observing the algorithmic complexity of programs with a mixture of algorithms and black-box software through visualization. Through two case studies, we demonstrate the effectiveness of complexity plots in complexity analysis in research, education and application. © 2013 The Author(s) Computer Graphics Forum © 2013 The Eurographics Association and Blackwell Publishing Ltd.

  20. 锑金精矿挥发特性及机理研究%Research on Volatilization Performance and Mechanism of Gold-bearing Antimony Concentrates

    Institute of Scientific and Technical Information of China (English)

    杨永斌; 刘庆华; 李骞; 姜涛; 郭宇峰

    2012-01-01

    研究了锑金精矿在氮气、氧气和一氧化碳三种气氛中的挥发特性,通过综合分析Sb、S两种元素的挥发行为,结合焙砂的微观形态分析,研究了三种气氛中的挥发反应机理.结果表明,锑金精矿在三种不同气氛下所发生的挥发反应各不相同.氮气气氛中,Sb2S3直接挥发;一氧化碳气氛中,除部分Sb2S3直接挥发外,还有一部分Sb2S3被还原成难挥发的金属Sb以熔融态的形式残留在焙砂中,同时生成COS气态产物进入气相;氧气气氛中,Sb2S3被气相中的O2氧化,一部分生成难挥发的Sb2O4残留在焙砂中,另一部分以Sb2O3的形态挥发进入气相.%Research was carried out on volatilization performance of gold-bearing antimony concentrate in three different atmospheres such as N2, O2, CO. The volatilization reaction mechanism was studied by analyzing volatilization behaviour of Sb and S, as well as the micro-morphology of calcine. The results showed that volatilization reactions of gold-bearing antimony concentrate differed in three different atmospheres. In N2 atmosphere, Sb2S3 volatilized directly. In CO atmosphere, only a part of Sb2S3 volatilized directly and the rest part was reduced to low-volatile or non-volatile molten metal (Sb) which was remained in the calcine, generating gaseous product COS to enter into gas phase. In O2 atmosphere, Sb2S3 was oxidized by O2, partly being as low-volatile Sh2O3 remained in the calcine and partly in the form of Sb2O3 volatilized into gas phase.

  1. Investigation of strontium and uranium sorption onto zirconium-antimony oxide/polyacrylonitrile (Zr-Sb oxide/PAN) composite using experimental design

    Energy Technology Data Exchange (ETDEWEB)

    Cakir, Pelin; Inan, Suleyman, E-mail: suleyman.inan@ege.edu.tr; Altas, Yuksel

    2014-04-01

    Highlights: • We model Sr{sup 2+} and UO{sub 2}{sup 2+} sorption onto Zr-Sb oxide/PAN composite. • Central composite design was separately employed for Sr{sup 2+} and UO{sub 2}{sup 2+} sorption. • The model F values indicate that both models are statistically significant. • All of the single factors were determined as significant for the sorption of Sr{sup 2+} and UO{sub 2}{sup 2+}. • Zr-Sb oxide/PAN can be used effectively for Sr{sup 2+} and UO{sub 2}{sup 2+} removal from acidic solutions. - Abstract: A study on the sorption of strontium (Sr{sup 2+}) and uranium (UO{sub 2}{sup 2+}) onto zirconium-antimony oxide/PAN (Zr-Sb oxide/PAN) composite was conducted. The zirconium-antimony oxide was synthesized and was then turned into composite spheres by mixing it with polyacrylonitrile (PAN). The single and combined effects of independent variables such as initial pH, temperature, initial ion concentration and contact time on the sorption of Sr{sup 2+} and UO{sub 2}{sup 2+} were separately analyzed using response surface methodology (RSM). Central composite design (CCD) was separately employed for Sr{sup 2+} and UO{sub 2}{sup 2+} sorption. Analysis of variance (ANOVA) revealed that all of the single effects found statistically significant on the sorption of Sr{sup 2+} and UO{sub 2}{sup 2+}. Probability F-values (F = 2.45 × 10{sup −08} and F = 9.63 × 10{sup −12} for Sr{sup 2+} and UO{sub 2}{sup 2+}, respectively) and correlation coefficients (R{sup 2} = 0.96 for Sr{sup 2+} and R{sup 2} = 0.98 for UO{sub 2}{sup 2+}) indicate that both models fit the experimental data well. At optimum sorption conditions Sr{sup 2+} and UO{sub 2}{sup 2+} sorption capacities of the composite were found as 39.78 and 60.66 mg/g, respectively. Sorption isotherm data pointed out that Langmuir model is more suitable for the Sr{sup 2+} sorption, whereas the sorption of UO{sub 2}{sup 2+} was correlated well with the Langmuir and Freundlich models. Thermodynamic parameters such as

  2. PREPARATION AND CHARACTERIZATION OF ANTIMONY DOPED TIN OXIDE NANOPARTICLES%纳米锑掺杂氧化锡的制备及表征

    Institute of Scientific and Technical Information of China (English)

    龚圣; 陈泽成; 唐富龙; 皮丕辉; 文秀芳; 郑大锋; 程江; 杨卓如

    2009-01-01

    SnCl4·5H2O and SbCl3 were used as the initial materials to prepare antimony-doped tin oxide (ATO) nanoparticles by sol-gel method combined with the supercritical fluid drying technique. The microstructure and doping mechanism of the precursor and the ATO particles were investigated by simultaneous thermogravimetry-differential scanning calorimetry, X-ray diffraction, field emission scanning electron microscopy and transmission electron microscopy. The effect of the drying method and the annealing temperature on the morphology, size, dispersion and crystallinity of particles were also investigated. The mechanism of the super-critical CO2 fluid drying on the precursor alcogels was discussed. The results show that the doped ATO particles with a soft agglomer-ate and a tetragonal phase structure in the size range of 15-30 nm could be obtained.%以无机盐SnCl4·5H2O和SbCl3为初始原料,以乙醇作为溶剂,采用溶胶-凝胶法结合超临界流体干燥(supercritical fluid drying,SCFD)技术制备了纳米锑掺杂氧化锡(antimony doped tin oxide.ATO)粉体.通过热重-差示扫描热分析、X射线衍射、扫描电子显微镜、透射电镜,对前驱体粒子以及ATO粒子的结构进行了分析.探讨了热处理温度、前驱体千燥方式对前驱体以及纳米粒子的形貌、粒径、分散性、晶型、结晶度的影响,并讨论了SCFD技术干燥前驱体的机理.结果表明:采用溶胶-凝胶法结合超临界CO2干燥技术,在给定的反应条件下,能够制得疏松的、良好掺杂的四方型结构的纳米ATO粒子,粒径约15~30nm,分散性好.

  3. Effects of Antimony on Microstructure and Mechanical Properties of A356 Alloy%Sb变质A356合金的组织与力学性能

    Institute of Scientific and Technical Information of China (English)

    申玉彬; 王明星; 刘志勇; 刘忠侠; 宋天福

    2012-01-01

    The modification of antimony (Sb) on eutectic Si phase in A356 aluminum-silicon alloy and the effects of rare earth (RE) on the modification efficiency of antimony were investigated, and effects of the strontium (Sr) on A356 alloy were analyzed comparatively. The tensile and fatigue properties of the Sb, Sb+RE or Sr modified A356 alloys were also analyzed comparatively. The results show that Sb can refine the eutectic silicon phases in A356 alloy significantly from plate-like into fine fibrous structure. , However, the modification efficiency of Sb is.lower than Sr. The modification effects can be improved obviously in Sb modified A356 aluminum-silicon alloy with the addition of a little RE, decreasing of Sb content for achieving the desirable modification efficiency. The tensile properties of the Sb or Sb + RE modified A356 alloys are lower than those of the Sr modified alloy, however, the fatigue properties are superior to that of the Sr modified alloy, which may be attributed to the higher compactness and less casting defects in Sb or Sb+RE modified alloys compared with the Sr modified alloy.%研究了Sb对A356合金中共晶Si相的变质作用及RE对Sb变质作用的影响,并且与Sr变质合金进行了比较,对Sb、Sb+RE以及Sr变质A356合金的拉伸及疲劳性能进行了对比.结果表明,Sb的A356合金变质使共晶Si相由粗大的板片状转化为细小的纤维状,但变质效果不如Sr;用Sb变质处理时,加入少量的RE,可明显改善Sh的变质效果,降低获得最佳变质效果的Sb含量;合金变质的力学性能不如Sr变质合金,但疲劳性能明显优于Sr变质合金.其原因可能与Sb或Sb+RE变质合金的致密性较Sr变质合金高、铸造缺陷较Sr变质合金少有关.

  4. A study on antimony determination in environmental samples by neutron activation analysis: validation of the methodology and determination of the uncertainty of the measurement

    International Nuclear Information System (INIS)

    Antimony is an element found in low concentrations in the environment. However, its determination has attracted great interest due to the knowledge of its toxicity and increasing application in industry. The determination of antimony has been a challenge for researchers since this element is found in low concentrations which make its analysis a difficult task. Therefore, although neutron activation analysis (NAA) is an appropriate method for the determination of various elements in different types of matrix, in the case of Sb its analysis presents some difficulties, mainly due to spectral interferences. The objective of this research was to validate the NAA method for Sb determination in environmental samples. To establish appropriate conditions for Sb determinations, preliminary assays were carried out for further analysis of certified reference materials (CRM). The experimental procedure was to irradiate samples with a synthetic Sb standard for a period of 8 or 16 hours in the IEA-R1 nuclear research reactor, followed by gamma ray spectrometry. The quantification of Sb was performed by measuring the radioactive isotopes of 122Sb and '124Sb. The results of preliminary assays indicated the presence of Sb in Whatman no 40 filter paper used in the preparation of the synthetic standard, but at very low concentrations, which could be considered negligible. In the case of the plastic material used in bags for the sample irradiation, it should be chosen carefully, because depending on the thickness, they may contain Sb. The analyses of the stability of the diluted Sb standard solution showed no change in the Sb concentration within eight months after its preparation. Results obtained in the analysis of certified reference materials indicated the interference of 76As and also of 134Cs and 152Eu in the Sb determinations by measuring '122Sb, due to the proximity of the gamma ray energies. The high activity of '24Na can also mask the peak of 122Sb hindering its detection

  5. Engaging complexity

    Directory of Open Access Journals (Sweden)

    Gys M. Loubser

    2014-01-01

    Full Text Available In this article, I discuss studies in complexity and its epistemological implications for systematic and practical theology. I argue that engagement with complexity does not necessarily assurea non-reductionist approach. However, if complexity is engaged transversally, it becomes possible to transcend reductionist approaches. Moreover, systematic and practical the ologians can draw on complexity in developing new ways of understanding and, therefore, new ways of describing the focus, epistemic scope and heuristic structures of systematic and practical theology. Firstly, Edgar Morin draws a distinction between restricted and general complexity based on the epistemology drawn upon in studies in complexity. Moving away from foundationalist approaches to epistemology, Morin argues for a paradigm of systems. Secondly,I discuss Kees van Kooten Niekerk�s distinction between epistemology, methodology andontology in studies in complexity and offer an example of a theological argument that drawson complexity. Thirdly, I argue for the importance of transversality in engaging complexity by drawing on the work of Wentzel van Huyssteen and Paul Cilliers. In conclusion, I argue that theologians have to be conscious of the epistemic foundations of each study in complexity, and these studies illuminate the heart of Reformed theology.Intradisciplinary and/or interdisciplinary implications: Therefore, this article has both intradisciplinary and interdisciplinary implications. When theologians engage studies incomplexity, the epistemological roots of these studies need to be considered seeing thatresearchers in complexity draw on different epistemologies. Drawing on transversality wouldenhance such considerations. Furthermore, Edgar Morin�s and Paul Cilliers� approach tocomplexity will inform practical and theoretical considerations in church polity and unity.

  6. Simplifying complexity

    NARCIS (Netherlands)

    Leemput, van de I.A.

    2016-01-01

    In this thesis I use mathematical models to explore the properties of complex systems ranging from microbial nitrogen pathways and coral reefs to the human state of mind. All are examples of complex systems, defined as systems composed of a number of interconnected parts, where the systemic behavior

  7. Carney Complex

    Science.gov (United States)

    ... of Carney complex are Cushing’s syndrome and multiple thyroid nodules (tumors). Cushing’s syndrome features a combination of weight gain, ... with Carney complex include adrenocortical carcinoma , pituitary gland tumors , thyroid , colorectal , liver and pancreatic cancers . Ovarian cancer in ...

  8. Surface plasmon resonance in nano-gold antimony glass-ceramic dichroic nanocomposites: One-step synthesis and enhanced fluorescence application

    International Nuclear Information System (INIS)

    A single-step melt-quench in situ thermochemical reduction technique has been used to synthesize a new series of Auo nanoparticles embedded antimony glass-ceramic (K2O-B2O3-Sb2O3-ZnO) dichroic nanocomposites. X-ray and selected area electron diffractions manifest growth of Auo nanoparticles along (2 0 0) planes. The particle sizes obtained from X-ray diffraction patterns are found to vary in the range 4-21 nm. Dichroic behavior is attributed to the elliptical shape gold nanoparticles having aspect ratio 1.2, as observed from the transmission electron microscopy (TEM) images. The Auo nanoparticles exhibit surface plasmon resonance band (SPR) around 600 nm, which experiences red-shifts with increasing Au concentration. These nanocomposites when co-doped with Sm2O3 and excited at 949 nm, exhibit 2-fold intensification of 636 nm red emission transition (4G5/2 → 6H9/2) due to SPR induced local field enhancement of Auo nanoparticles and are promising materials for display applications.

  9. Low-voltage antimony-doped SnO2 nanowire transparent transistors gated by microporous SiO2-based proton conductors

    Institute of Scientific and Technical Information of China (English)

    Xuan Rui-Jie; Liu Hui-Xuan

    2012-01-01

    A battery drivable low-voltage transparent lightly antimony(Sb)-doped SnO2 nanowire electric-double-layer (EDL)field-effect transistor (FET) is fabricated on an ITO glass substrate at room temperature.An ultralow operation voltage of 1 V is obtained on account of an untralarge specific gate capacitance (~ 2.14 μF/cm2) directly bound up with mobile ions-induced EDL (sandwiched between the top and bottom electrodes) effect.The transparent FET shows excellent electric characteristics with a field-effect mobility of 54.43 cm2/V.s,current on/off ration of 2 × 104,and subthreshold gate voltage swing (S =dVgs/d(logIds)) of 140 mV/decade.The threshold voltage Vth (0.1 V) is estimated which indicates that the SnO2 namowire transistor operates in an n-type enhanced mode.Such a low-voltage transparent nanowire transistor gated by a microporous SiO2-based solid electrolyte is very promising for battery-powered portable nanoscale sensors.

  10. Ion-exchange separation of radioiodine and its application to production of {sup 124}I by alpha particle induced reactions on antimony

    Energy Technology Data Exchange (ETDEWEB)

    Shuza Uddin, Md. [Forschungszentrum Juelich (Germany). Inst. fuer Neurowissenschaften und Medizin, INM-5: Nuklearchemie; Atomic Energy Research Establishment, Inst. of Nuclear Science and Technology, Dhaka (Bangladesh); Qaim, Seyed M.; Spahn, Ingo; Spellerberg, Stefan; Scholten, Bernhard; Coenen, Heinz H. [Forschungszentrum Juelich (Germany). Inst. fuer Neurowissenschaften und Medizin, INM-5: Nuklearchemie; Hermanne, Alex [Vrije Univ. Brussel (Belgium). Cyclotron Lab.; Hossain, Syed Mohammod [Atomic Energy Research Establishment, Inst. of Nuclear Science and Technology, Dhaka (Bangladesh)

    2015-07-01

    The basic parameters related to radiochemical separation of iodine from tellurium and antimony by anion-exchange chromatography using the resin Amberlyst A26 were studied. The separation yield of {sup 124}I amounted to 96% and the decontamination factor from {sup 121}Te and {sup 122}Sb was > 10{sup 4}. The method was applied to the production of {sup 124}I via the {sup 123}Sb(α, 3n) reaction. In an irradiation of 110 mg of {sup nat}Sb{sub 2}O{sub 3} (thickness ∝0.08 g/cm{sup 2}) with 38 MeV α-particles at 1.2 μA beam current for 4 h, corresponding to the beam energy range of E{sub α} = 37 → 27 MeV, the batch yield of {sup 124}I obtained was 12.42 MBq and the {sup 125}I and {sup 126}I impurities amounted to 3.8% and 0.7%, respectively. The experimental batch yield of {sup 124}I amounted to 80% of the theoretically calculated value but the level of the radionuclidic impurities were in agreement with the theoretical values. About 96% of the radioiodine was in the form of iodide and the inactive impurities (Te, Sb, Sn) were below the permissible level. Due to the relatively high level of radionuclidic impurity the {sup 124}I produced would possibly be useful only for restricted local consumption or for animal experiments.

  11. Antimony-Supported Cu4I4 Cuboid with Short Cu-Cu Bonds: Structural Premise for Near-Infrared Thermoluminescence.

    Science.gov (United States)

    Taylor, William V; Soto, Ulysses H; Lynch, Vincent M; Rose, Michael J

    2016-04-01

    Herein we report the synthesis, temperature-dependent X-ray structures (100, 150, 200, 250, 273, and 300 K), and solid-state emissive properties of the antimony-copper(I)-iodo cluster [Cu4(I)4(Sb(i)Pr3)4] (1), supported by the trialkylantimony donor Sb(i)Pr3. Overall, 1 exhibits a distorted cuboidal structure, wherein a twisting of the "cube" generates an interconnected Cu4 tetrahedron, as well as long Cu-I and Cu-Sb bonds [e.g., 2.707(2) and 2.571(2) Å]; in the 100 K X-ray structure, the Cu-Cu bonds are quite short [2.761(3) Å]. Solid-state emission spectra of 1 were obtained over a range of temperatures (163-298 K), wherein 1 exhibits only a low-energy emission feature centered near 700 nm (λEm = 711 nm, fwhm = 150 nm, and λEx = 390 nm). Because 1 contains no aryl units, the emission spectrum (and absorption) can be unambiguously attributed to the Cu4I4 core [no L (pnictogen ligand) component]. The luminescence is sharply attenuated upon warming from 150 to 200 K. An overlaid plot of the emissive properties of 1 and its Cu-Cu bond distances [2.761(3)-2.836(4) Å] reveal that ∼2.80 Å represents a critical crossing point for low-energy thermoluminescence in Cu4-based clusters. PMID:27010917

  12. Sources, migration and transformation of antimony contamination in the water environment of Xikuangshan, China: Evidence from geochemical and stable isotope (S, Sr) signatures.

    Science.gov (United States)

    Wen, Bing; Zhou, Jianwei; Zhou, Aiguo; Liu, Cunfu; Xie, Lina

    2016-11-01

    The Xikuangshan (XKS) mine in central China is the largest antimony (Sb) mine in the world. The mining activity has seriously contaminated the waters in the area. To determine the sources, migration and transformation of Sb contamination, 32 samples from groundwater (aquifer water), surface water and mine water were collected for water chemistry, trace element and SSO4 and Sr stable isotope analyses. The results showed that the groundwater and surface water were in an oxidized environment. The SSO4 and Sr isotope compositions in the water indicated that dissolved Sb and SO4(2) originated from sulfide mineral (Sb2S3) oxidation, whereas radiogenic Sr may have been sourced from silicified limestone and stibnite in the Shetianqiao aquifer. Furthermore, a positive correlation between δ(34)SSO4 and δ(87)Sr values revealed that the Sr, S and Sb in the waters had a common contamination source, i.e., silicified limestone and stibnite, whereas the Sr, S and Sb in rock and ore were sourced from Proterozoic basement clastics. The analysis also indicated that the isotope composition of dissolved SO4(2-) had been influenced by slight bacterial SO4 reduction in the Magunao aquifer. Mining or rock collapse may have caused Shetianqiao aquifer water to contaminate the Magunao aquifer water via mixing. This study has demonstrated that the stable isotopes of (34)SSO4 and (87)Sr, combined with hydrochemical methods, are effective in tracking the sources, migration and transformation of Sb contamination. PMID:27341112

  13. Structural, electrical, and optical properties of antimony-doped tin oxide films prepared at room temperature by radio frequency magnetron sputtering for transparent electrodes

    International Nuclear Information System (INIS)

    Antimony-doped tin oxide (ATO) films were prepared on 7059 Corning glass substrate by the radio frequency (rf) magnetron sputtering method using SnO2 target mixed with Sb of 6 wt % at room temperature. The working pressure was varied from 0.67 to 2 Pa in steps of 0.67 Pa, and the rf power was varied from 100 to 175 W in steps of 25 W at room temperature. The thickness of the deposited ATO films was about 150 nm. X-ray diffraction (XRD) measurements showed the ATO films to be crystallized with a strong (101) preferred orientation as the rf power is increased. The spectra revealed that the deposited films were polycrystalline, retaining the tetragonal structure. The grain size was estimated from the XRD spectra using the Scherrer equation and found to decrease with a decrease in the working pressure and an increase in the rf power, while the surface roughness was observed to be smoothened. The ATO film that was deposited at a working pressure of 0.67 Pa with rf power of 175 W showed the lowest resistivity of 8.6x10-3 Ω cm, and the optical transmittance was 86.5% in the visible wavelength range from 400 to 800 nm.

  14. (Vapor + Liquid) Equilibrium (VLE) for Binary Lead-Antimony System in Vacuum Distillation: New Data and Modeling Using Nonrandom Two-Liquid (NRTL) Model

    Science.gov (United States)

    Xu, Junjie; Kong, Lingxin; Xu, Baoqiang; Yang, Bin; You, Yanjun; Xu, Shuai; Zhou, Yuezhen; Li, Yifu; Liu, Dachun

    2016-09-01

    In this work, new experimental vapor-liquid equilibrium (VLE) data of lead-antimony alloy (Pb-Sb alloy) in vacuum distillation are reported. The activity coefficients of components of Pb-Sb alloy were calculated by using the NRTL model. The calculated average relative deviations were ±0.1425 and ±0.2433 pct, and the average standard deviations were ±0.0009 and ±0.0007, respectively, for Pb and Sb. The VLE phase diagrams, such as the temperature composition ( T- x) and pressure composition ( P-x) diagrams of Pb-Sb alloy in vacuum distillation were predicted based on the NRTL model and VLE theory. The predicted results are consistent with the new experimental data indicating that VLE phase diagrams obtained by this method are reliable. The VLE phase diagrams of alloys will provide an effective and intuitive way for the technical design and realization of recycling and separation processes. The VLE data may be used in separation processes design, and the thermodynamic properties as the key parameters in specific applications.

  15. Investigation of upconversion luminescence in Yb3+/Tm3+/Ho3+ triply doped antimony-germanate glass and double-clad optical fiber

    Science.gov (United States)

    Zmojda, Jacek; Kochanowicz, Marcin; Miluski, Piotr; Righini, Giancarlo C.; Ferrari, Maurizio; Dorosz, Dominik

    2016-08-01

    The optical properties of novel antimony-germanate glass and optical fiber co-doped with Yb3+/Tm3+/Ho3+ ions were presented. White light luminescence in glass was observed as a result of energy transfer with upconversion between donor (Yb3+) and acceptors (Tm3+, Ho3+) ions under 976 nm excitation. The double-clad optical fiber with off-set core co-doped with Yb2O3/Tm2O3/Ho2O3 system was fabricated using a modified rod-in-tube technique. In glass co-doped with 0.5 mol%Yb2O3/0.1 mol%Tm2O3/0.2 mol%Ho2O3 the spectral distribution of three luminescence bands (478, 545 and 660 nm) corresponds to x = 0.35 and y = 0.32 CIE coordinates. In comparison to glass the optical fiber emission are located in the green region (CIE, x = 0.37, y = 0.49).

  16. Antimony speciation in soils: improving the detection limits using post-column pre-reduction hydride generation atomic fluorescence spectroscopy (HPLC/pre-reduction/HG-AFS).

    Science.gov (United States)

    Quiroz, Waldo; Olivares, David; Bravo, Manuel; Feldmann, Jorg; Raab, Andrea

    2011-04-15

    HG-AFS is highly sensitive and low cost detection system and its use for antimony chemical speciation coupled to HPLC is gaining popularity. However speciation analysis in soils is strongly hampered because the most efficient extractant reported in the literature (oxalic acid) strongly inhibits the generation of SbH(3) by Sb(V), the major species in this kind of matrix, severely affecting its detection limits. The purpose of this research is to reduce the detection limit of Sb(V), by using a post column on-line reduction system with l-cysteine reagent (HPLC/pre-reduction/HG-AFS). The system was optimized by experimental design, optimum conditions found were 2% (w/v) and 10°C temperature coil. Detection limits of Sb(V) and Sb(III) in oxalic acid (0.25 mol L(-1)) were improved from 0.3 and 0.1 μg L(-1) to 0.07 and 0.07 μg L(-1), respectively. The methodology developed was applied to Chilean soils, where Sb(V) was the predominant species.

  17. Managing Complexity

    DEFF Research Database (Denmark)

    Maylath, Bruce; Vandepitte, Sonia; Minacori, Patricia;

    2013-01-01

    and into French. The complexity of the undertaking proved to be a central element in the students' learning, as the collaboration closely resembles the complexity of international documentation workplaces of language service providers. © Association of Teachers of Technical Writing.......This article discusses the largest and most complex international learning-by-doing project to date- a project involving translation from Danish and Dutch into English and editing into American English alongside a project involving writing, usability testing, and translation from English into Dutch...

  18. Complex variables

    CERN Document Server

    Fisher, Stephen D

    1999-01-01

    The most important topics in the theory and application of complex variables receive a thorough, coherent treatment in this introductory text. Intended for undergraduates or graduate students in science, mathematics, and engineering, this volume features hundreds of solved examples, exercises, and applications designed to foster a complete understanding of complex variables as well as an appreciation of their mathematical beauty and elegance. Prerequisites are minimal; a three-semester course in calculus will suffice to prepare students for discussions of these topics: the complex plane, basic

  19. Complex Covariance

    Directory of Open Access Journals (Sweden)

    Frieder Kleefeld

    2013-01-01

    Full Text Available According to some generalized correspondence principle the classical limit of a non-Hermitian quantum theory describing quantum degrees of freedom is expected to be the well known classical mechanics of classical degrees of freedom in the complex phase space, i.e., some phase space spanned by complex-valued space and momentum coordinates. As special relativity was developed by Einstein merely for real-valued space-time and four-momentum, we will try to understand how special relativity and covariance can be extended to complex-valued space-time and four-momentum. Our considerations will lead us not only to some unconventional derivation of Lorentz transformations for complex-valued velocities, but also to the non-Hermitian Klein-Gordon and Dirac equations, which are to lay the foundations of a non-Hermitian quantum theory.

  20. Design of stereoelectronically promoted super lewis acids and unprecedented chemistry of their complexes.

    Science.gov (United States)

    Foroutan-Nejad, Cina; Vicha, Jan; Marek, Radek

    2014-09-01

    A new family of stereoelectronically promoted aluminum and scandium super Lewis acids is introduced on the basis of state-of-the-art computations. Structures of these molecules are designed to minimize resonance electron donation to central metal atoms in the Lewis acids. Acidity of these species is evaluated on the basis of their fluoride-ion affinities relative to the antimony pentafluoride reference system. It is demonstrated that introduced changes in the stereochemistry of the designed ligands increase acidity considerably relative to Al and Sc complexes with analogous monodentate ligands. The high stability of fluoride complexes of these species makes them ideal candidates to be used as weakly coordinating anions in combination with highly reactive cations instead of conventional Lewis acid-fluoride complexes. Further, the interaction of all designed molecules with methane is investigated. All studied acids form stable pentavalent-carbon complexes with methane. In addition, interactions of the strongest acid of this family with very weak bases, namely, H2, N2, carbon oxides, and noble gases were investigated; it is demonstrated that this compound can form considerably stable complexes with the aforementioned molecules. To the best of our knowledge, carbonyl and nitrogen complexes of this species are the first hypothetical four-coordinated carbonyl and nitrogen complexes of aluminum. The nature of bonding in these systems is studied in detail by various bonding analysis approaches. PMID:25055748

  1. Design of stereoelectronically promoted super lewis acids and unprecedented chemistry of their complexes.

    Science.gov (United States)

    Foroutan-Nejad, Cina; Vicha, Jan; Marek, Radek

    2014-09-01

    A new family of stereoelectronically promoted aluminum and scandium super Lewis acids is introduced on the basis of state-of-the-art computations. Structures of these molecules are designed to minimize resonance electron donation to central metal atoms in the Lewis acids. Acidity of these species is evaluated on the basis of their fluoride-ion affinities relative to the antimony pentafluoride reference system. It is demonstrated that introduced changes in the stereochemistry of the designed ligands increase acidity considerably relative to Al and Sc complexes with analogous monodentate ligands. The high stability of fluoride complexes of these species makes them ideal candidates to be used as weakly coordinating anions in combination with highly reactive cations instead of conventional Lewis acid-fluoride complexes. Further, the interaction of all designed molecules with methane is investigated. All studied acids form stable pentavalent-carbon complexes with methane. In addition, interactions of the strongest acid of this family with very weak bases, namely, H2, N2, carbon oxides, and noble gases were investigated; it is demonstrated that this compound can form considerably stable complexes with the aforementioned molecules. To the best of our knowledge, carbonyl and nitrogen complexes of this species are the first hypothetical four-coordinated carbonyl and nitrogen complexes of aluminum. The nature of bonding in these systems is studied in detail by various bonding analysis approaches.

  2. Simplifying complexity

    OpenAIRE

    Leemput, van de, J.C.H.

    2016-01-01

    In this thesis I use mathematical models to explore the properties of complex systems ranging from microbial nitrogen pathways and coral reefs to the human state of mind. All are examples of complex systems, defined as systems composed of a number of interconnected parts, where the systemic behavior leads to the emergence of properties that would not be expected from behavior or properties of the individual parts of the system. Although the full behavior of the systems I address will probably...

  3. Changes induced by gamma radiation in nanocomposites based on copper II and antimony sulfides in commercial poly(methyl methacrylate) matrix; Alteracoes induzidas pela radiacao gama em nanocompositos a base dos sulfetos de cobre II e de antimonio na matriz de poli(metacrilato de metila) comercial

    Energy Technology Data Exchange (ETDEWEB)

    Albuquerque, M.C.C. de; Garcia, O.P.; Aquino, K.A.S.; Araujo, E.S., E-mail: esa@ufpe.b [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil). Dept. de Energia Nuclear

    2010-07-01

    Poly (methyl methacrylate) (PMMA) is a polymer with wide application in the manufacture of medical devices that is exposed to gamma irradiation. Currently the use of composite materials has been disseminated and PMMA is an excellent polymer matrix to package various materials. This study aimed to analyze the changes induced by gamma irradiation (25 kGy) on the properties of PMMA nanocomposites with nanoparticles of copper II sulfide (250nm-900nm) and antimony sulfite (300-500 nm). The nanoparticles were added to the polymer in different concentrations and synthesized by ultrasonic irradiation from the corresponding chlorides with thioacetamide. Viscometric results showed a good radioprotective effect of nanoparticles of copper and antimony. It was found a good protection of nanoparticles on PMMA matrix in the concentration of 0.3% wt. The protections of 75% and 50% were calculated for nanoparticles of antimony and copper II, respectively. (author)

  4. Complex networks: Patterns of complexity

    Science.gov (United States)

    Pastor-Satorras, Romualdo; Vespignani, Alessandro

    2010-07-01

    The Turing mechanism provides a paradigm for the spontaneous generation of patterns in reaction-diffusion systems. A framework that describes Turing-pattern formation in the context of complex networks should provide a new basis for studying the phenomenon.

  5. Complex analysis

    CERN Document Server

    Freitag, Eberhard

    2005-01-01

    The guiding principle of this presentation of ``Classical Complex Analysis'' is to proceed as quickly as possible to the central results while using a small number of notions and concepts from other fields. Thus the prerequisites for understanding this book are minimal; only elementary facts of calculus and algebra are required. The first four chapters cover the essential core of complex analysis: - differentiation in C (including elementary facts about conformal mappings) - integration in C (including complex line integrals, Cauchy's Integral Theorem, and the Integral Formulas) - sequences and series of analytic functions, (isolated) singularities, Laurent series, calculus of residues - construction of analytic functions: the gamma function, Weierstrass' Factorization Theorem, Mittag-Leffler Partial Fraction Decomposition, and -as a particular highlight- the Riemann Mapping Theorem, which characterizes the simply connected domains in C. Further topics included are: - the theory of elliptic functions based on...

  6. Bacillus sp.处理锑矿选矿废水的优化试验%Experimental study of optimization of antimony ore-processed wastewater treatment by Bacillus sp.

    Institute of Scientific and Technical Information of China (English)

    成应向; 李小娇; 向仁军; 龚道新; 王强强; 肖亚琼

    2012-01-01

    Antimony ore-processed wastewater was treated with the optimized bacterium Bacillus sp. The effects of the evaluation indices, including the amount of inoculation, pH value, processing time, and temperature, on the treatment of antimony ore-processed wastewater were studied through orthogonal experiments. The results show that the degrees of effects of the indices on the removal of antimony from wastewater by Bacillus sp . Are in the following descending order: the amount of inoculation, pH value, processing time, and temperature. The optimal treatment conditions were attained when the amount of inoculation was 5 % , the PH value was 2.5, the processing time was three days, and the temperature was 30^1.%用某芽孢杆菌属微生物(Bacillus sp.)处理锑矿选矿废水.通过正交实验,研究该微生物在处理锑矿选矿废水过程中微生物接种量、pH值、处理时间、温度对去除效果的影响.结果表明:Bacillus sp.对废水中锑的去除效果影响程度由大到小的顺序为:微生物接种量、pH值、处理时间、温度;最优实验条件:微生物接种量为5%、pH值为2.5、处理时间为3d,处理温度为30℃.

  7. Tin(2) difluoride and antimony(3) trifluoride as fluorine donors in reactions with tantalum halides in various solvents

    International Nuclear Information System (INIS)

    The reactions of SnF2, SbF3 with TaF5 and TaCl5 in acetonitrile and dimethylsulfoxide were studied by means of 19F and 119Sn NMR. SnF2 and SbF3 were established to be donors of fluorine ions for the tantalum(5). It was found that the anion and cation tantalum fluorochloride complexes were formed in acetonitrile, and [TaF6]- was dominated in dimethylsulfoxide. In the solution the tin(2) is present as fluorine-containing polymer cations. Dimethylsulfoxide, as distinct from acetonitrile, leads to disproportionation of tantalum fluorochlorides

  8. 从铅阳极泥中湿法提取铋、锑试验研究%Extraction of Bismuth and Antimony by Wet-process From Lead Anode Mud

    Institute of Scientific and Technical Information of China (English)

    贾辉; 王兴; 崔家友; 侯绍彬; 林浩

    2014-01-01

    Leaching of bismuth and antimony from lead anode mud oxidized at high temperature using hydrochloric acid as leaching agent ,ferric chloride as oxidant ,sodium chloride to provide more chloride ions was investigated .The effects of oxidizing temperature of lead anode mud ,hydrochloric acid concentration ,leaching temperature ,reaction time ,ratio between liquid volume and solid mass ,the amount of ferric chloride and sodium chloride on leaching of bismuth and antimony were examined . The experimental results show that the pretreatment for lead anode slime has a greater influence on the leaching of bismuth and antimony .Under the conditions of hydrochloric acid concentration of 5 mol/L ,ratio betw een liquid volume and solid mass of 5∶1 ,leaching temperature of 80 ℃ ,reaction time of 3 h ,ferric chloride concentration of 10 g/L ,sodium chloride concentration of 45 g/L ,the leaching of bismuth and antimony reach 99 .44% and 99 .69% respectively for the lead anode mud oxidized at 200 ℃ and through 200 mesh sieve .%介绍了以三氯化铁作氧化剂,氯化钠提供氯离子,用盐酸从高温氧化后的铅阳极泥中浸出铋、锑,考察了氧化温度、盐酸浓度、浸出温度、反应时间、液固体积质量比、三氯化铁和氯化钠用量对铋、锑浸出率的影响。试验结果表明:铅阳极泥预处理对铋、锑浸出率影响较大;铅阳极泥粉磨过200目筛,在氧化温度220℃、盐酸浓度5 mol/L、液固体积质量比5∶1、反应温度80℃、反应时间3 h、三氯化铁质量浓度10 g/L、氯化钠质量浓度45 g/L条件下,铋、锑浸出率分别为99.44%和99.69%,浸出效果较好。

  9. Complex Networks

    CERN Document Server

    Evsukoff, Alexandre; González, Marta

    2013-01-01

    In the last decade we have seen the emergence of a new inter-disciplinary field focusing on the understanding of networks which are dynamic, large, open, and have a structure sometimes called random-biased. The field of Complex Networks is helping us better understand many complex phenomena such as the spread of  deseases, protein interactions, social relationships, to name but a few. Studies in Complex Networks are gaining attention due to some major scientific breakthroughs proposed by network scientists helping us understand and model interactions contained in large datasets. In fact, if we could point to one event leading to the widespread use of complex network analysis is the availability of online databases. Theories of Random Graphs from Erdös and Rényi from the late 1950s led us to believe that most networks had random characteristics. The work on large online datasets told us otherwise. Starting with the work of Barabási and Albert as well as Watts and Strogatz in the late 1990s, we now know th...

  10. Failure of antimony trioxide to induce micronuclei or chromosomal aberrations in rat bone-marrow after sub-chronic oral dosing.

    Science.gov (United States)

    Kirkland, David; Whitwell, James; Deyo, James; Serex, Tessa

    2007-03-01

    Antimony trioxide (Sb2O3, CAS 1309-64-4) is widely used as a flame retardant synergist in a number of household products, as a fining agent in glass manufacture, and as a catalyst in the manufacture of various types of polyester plastics. It does not induce point mutations in bacteria or mammalian cells, but is able to induce chromosomal aberrations (CA) in cultured cells in vitro. Although no CA or micronuclei (MN) have been induced after acute oral dosing of mice, repeated oral dosing for 14 or 21 days resulted in increased CA in one report, but did not result in increased MN in another. In order to further investigate its in vivo genotoxicity, Sb2O3 was dosed orally to groups of rats for 21 days at 250, 500 and 1000 mg/kg day. There were no clinical signs of toxicity in the Sb2O3-exposed animals except for some reductions in body-weight gain in the top dose group. Toxicokinetic measurements in a separate study confirmed bone-marrow exposure, and at higher levels than would have been achieved by single oral dosing. Large numbers of cells were scored for CA (600 metaphases/sex group) and MN (12,000 PCE/sex group) but frequencies of CA or MN in Sb2O3-treated rats were very similar to controls, and not biologically or statistically different, at all doses. These results provide further indication that Sb2O3 is not genotoxic to the bone marrow of rodents after 21 days of oral administration at high doses close to the maximum tolerated dose. PMID:17174592

  11. Transport of antimony salts by Arabidopsis thaliana protoplasts over-expressing the human multidrug resistance-associated protein 1 (MRP1/ABCC1).

    Science.gov (United States)

    Gayet, Landry; Picault, Nathalie; Cazalé, Anne-Claire; Beyly, Audrey; Lucas, Philippe; Jacquet, Hélène; Suso, Henri-Pierre; Vavasseur, Alain; Peltier, Gilles; Forestier, Cyrille

    2006-12-22

    ABC transporters from the multidrug resistance-associated protein (MRP) subfamily are glutathione S-conjugate pumps exhibiting a broad substrate specificity illustrated by numerous xenobiotics, such as anticancer drugs, herbicides, pesticides and heavy metals. The engineering of MRP transporters into plants might be interesting either to reduce the quantity of xenobiotics taken up by the plant in the context of "safe-food" strategies or, conversely, in the development of phytoremediation strategies in which xenobiotics are sequestered in the vacuolar compartment. In this report, we obtained Arabidopsis transgenic plants overexpressing human MRP1. In these plants, expression of MRP1 did not increase plant resistance to antimony salts (Sb(III)), a classical glutathione-conjugate substrate of MRP1. However, the transporter was fully translated in roots and shoots, and targeted to the plasma membrane. In order to investigate the functionality of MRP1 in Arabidopsis, mesophyll cell protoplasts (MCPs) were isolated from transgenic plants and transport activities were measured by using calcein or Sb(III) as substrates. Expression of MRP1 at the plasma membrane was correlated with an increase in the MCPs resistance to Sb(III) and a limitation of the metalloid content in the protoplasts due to an improvement in Sb(III) efflux. Moreover, Sb(III) transport was sensitive to classical inhibitors of the human MRP1, such as MK571 or glibenclamide. These results demonstrate that a human ABC transporter can be functionally introduced in Arabidopsis, which might be useful, with the help of stronger promoters, to reduce the accumulation of xenobiotics in plants, such as heavy metals from multi-contaminated soils.

  12. People with diabetes, respiratory, liver or mental disorders, higher urinary antimony, bisphenol A, or pesticides had higher food insecurity: USA NHANES, 2005-2006.

    Science.gov (United States)

    Shiue, Ivy

    2016-01-01

    This study was aimed to examine the prevalence of food insecurity and what social, health, and environmental characteristics could constitute such situation in a national and population-based setting. Data was retrieved from the National Health and Nutrition Examination Survey, 2005-2006. Information on demographics, lifestyle factors, self-reported ever medical conditions in the past and self-reported food security conditions in the last 12 months calculated on the household level was obtained by household interview. Bloods and urines (subsample) were collected at the interview as well. Only adults aged 20 years and above (n = 4979) were included for statistical analysis in the present study. Chi-square test, t test, and survey-weighted logistic regression modeling were performed. Three thousand eight hundred thirty-four (77.9%) people were with full food security, 466 (9.5%) people were with marginal food security and 624 (12.7%) people were with low or very low food security. Being younger, having higher ratios of family income to poverty thresholds (due to low level of education or lack of financial support), having prior asthma, arthritis, chronic bronchitis, depression, diabetes, eczema, emphysema or liver problems, having higher levels of serum cotinine, urinary antimony, bisphenol A, pesticides, or having lower levels of urinary Benzophenone-3 were associated with food insecurity. In addition to socioeconomic and smoking conditions, evidence on people with several prior health conditions and being exposed to environmental chemicals and food insecurity is further provided. Future social, health and environmental policy, and programs protecting people from food insecurity by considering both health and environmental factors mentioned above would be suggested.

  13. In-situ growth of antimony sulfide in carbon nanoparticle matrix: Enhanced electrocatalytic activity as counter electrode in dye-sensitized solar cells

    Science.gov (United States)

    Sun, Panpan; Zhang, Ming; Ai, Changzhi; Wu, Zhixin; Lu, Shuang; Zhang, Xintong; Huang, Niu; Sun, Yihua; Sun, Xiaohua

    2016-07-01

    Considering the undesirable electrocatalytic activity toward I-/I3- redox system of prinstine antimony sulfide (Sb2S3) fabricated with the existing conditions, a mesoporous carbon nanoparticle film (CNP) is introduced here for in-situ growth of Sb2S3 to construct a Sb2S3@CNP hybrid catalyst. Based on a Sb-thiourea precursor solution, in-situ growth of Sb2S3 can be achieved via solution deposition (denoted as Sb2S3@CNP-S) as well as atmospheric pressure thermal evaporation (denoted as Sb2S3@CNP-T) in CNP matrix. Structural characterizations indicate that Sb2S3 particles have well dispersed in the pores of CNP matrix. Because of the introduction of porous and conductive CNP matrix to support Sb2S3, the hybrid catalyst exhibits lower charge transfer resistance at the catalyst/electrolyte interface and higher electrocatalytic activity. When used as counter electrode (CE) for dye-sensitized solar cells (DSSCs), devices using Sb2S3@CNP hybrid catalyst as CE produce fill factor of 67.6% and 66.3%, which is significantly higher than that using pristine Sb2S3 fabricated in our previous work (52.8%). Finally, the corresponding power conversion efficiencies reach 6.69% (Sb2S3@CNP-S) and 6.24% (Sb2S3@CNP-T), respectively, which are comparable to that using Pt CE measured under the same conditions (6.74%).

  14. 三氧化二锑纳米粒子的形貌控制合成%Synthesis of Shape Controllable Antimony Trioxide Nanoparticles

    Institute of Scientific and Technical Information of China (English)

    赵淑贤

    2015-01-01

    文章通过机械搅拌下,把三氯化锑乙醇溶液直接滴加到壬基苯酚聚氧乙烷(50)醚(TX-50)溶液中,得到了形貌较好、长20μm左右的带束状Sb2 O3纳米材料。通过X射线能谱( EDS),X射线衍射谱( XRD)和扫描电镜( SEM)对材料的结构和形貌进行了表征,研究了反应温度、氨水浓度、表面活性剂对三氧化二锑纳米粒子形貌和纯度的影响。相对于商品Sb2 O3,阻燃性能有所提高。%The belt-bundle Sb2 O3 nanoparticles were synthesized by adding dropwise the antimony butter etha⁃nol solution into the Nonylphenol polyethylene oxide ethane (50) ether aqueous solution(TX-50) with stirring. The effects of reaction temperature, ammonia concentration and surfactant on the morphology and purity of nanopar⁃ticles were studied respectively. The purity, crystal structure and morphology were characterized by energy disper⁃sive X-ray spectroscopy( EDS)、X-ray diffraction( XRD) and scanning electron microscopy ( SEM) . The flame re⁃tardant property of synthesized Sb2 O3 was improved compared with commercial grade Sb2 O3 .

  15. Bacillus sp.Treating Wastewater Containing Antimony%Bacillus sp.处理含锑废水试验研究

    Institute of Scientific and Technical Information of China (English)

    李小娇; 成应向; 龚道新; 向仁军; 王强强

    2012-01-01

    利用某芽孢杆菌属微生物(Bacillus sp.)对锑矿选矿废水进行了处理.研究微生物的接种量、作用时间、温度、体系pH值等对废水中Sb的去除效果的影响.结果表明:作用时间4d、微生物接种量为5%、处理体系pH为2、最佳处理体系温度为30℃时,效果最佳,对废水中Sb的去除率达到99.75%,处理后废水中Sb的浓度由122.21 mg/L降低至0.30 mg/L,出水Sb浓度低于湖南省地方标准排放限值0.50 mg/L.%Antimony ore dressing wastewater was treated by using a certain Bacillus microorganism (Bacillus sp.). Sb removal efficiency in mineral processing wastewater was affected by microbial inoculums size, treating time, temperature and the system pH value. Results showed that the best removal efficiency of Sb in mineral processing wastewater could reach 99.75% in 4d under the optimum conditions of 30 ℃, microbial inoculated quantity 5% and pH value 2.0. After the treatment, the concentration of Sb in wastewater was reduced from 122.21 mg/L to 0.30 mg/L, which was lower than local industrial wastewater discharge standard of 0.50 mg/L.

  16. Managing Complexity

    Energy Technology Data Exchange (ETDEWEB)

    Chassin, David P.; Posse, Christian; Malard, Joel M.

    2004-08-01

    Physical analogs have shown considerable promise for understanding the behavior of complex adaptive systems, including macroeconomics, biological systems, social networks, and electric power markets. Many of today’s most challenging technical and policy questions can be reduced to a distributed economic control problem. Indeed, economically-based control of large-scale systems is founded on the conjecture that the price-based regulation (e.g., auctions, markets) results in an optimal allocation of resources and emergent optimal system control. This paper explores the state of the art in the use physical analogs for understanding the behavior of some econophysical systems and to deriving stable and robust control strategies for them. In particular we review and discussion applications of some analytic methods based on the thermodynamic metaphor according to which the interplay between system entropy and conservation laws gives rise to intuitive and governing global properties of complex systems that cannot be otherwise understood.

  17. PS complex

    CERN Multimedia

    1972-01-01

    A view of the present PS complex taken at the end of 1972. The earth embankment covering the Ring is clearly visible; in the foreground are the North and South Experimental Halls; to the right is the East Hall, and to the left the Booster surface buildings. The West Hall is too far to the left to seen, and also invisible is the SPS being constructed.

  18. Avaliação do efeito cumulativo do antimoniato de meglumina sobre a prole de camundongos swiss: ensaio biológico Evaluate the cumulative effect of meglumine antimoniate on the progeny of swiss mice: biologic assay

    Directory of Open Access Journals (Sweden)

    Michelle Rodrigues dos Santos

    2008-02-01

    Full Text Available OBJETIVOS: Avaliar o efeito do antimoniato de meglumina na transferência materno-fetal na geração F1 (prole de matrizes expostas ao composto, e conseqüências em progênies F2. MÉTODOS: Camundongos fêmeas Swiss foram tratados com antimoniato de meglumina, via subcutânea, com administração diária, do sétimo ao 12º dia de gestação (ddg, na dose equivalente a 100mgSb v/kg peso/dia. O grupo controle recebeu apenas o veículo (água destilada. Após o nascimento da prole (geração F1, 59 fêmeas foram examinadas diariamente para determinação do ciclo estral. Quando determinado o ciclo estro, acasalou-se 18 fêmeas com machos da mesma linhagem. No 18º ddg, as fêmeas foram eutanasiadas por câmara de CO2, o abdômen incisado e o útero exposto, quando avaliou-se os sítios de desenvolvimento embrionário e fetal quanto ao número de reabsorções, fetos vivos e mortos. Todos os fetos e placentas foram pesados para calcular o índice placentário. Três placentas de cada ninhada foram separadas para análise microscópica. RESULTADOS: A exposição ao antimoniato de meglumina não interferiu no ciclo estral dos animais tratados, pelo fato de não alterar o intervalo precoital e o índice de fertilidade. Não foram observadas alterações placentárias em progênies F2. CONCLUSÃO: O antimoniato de meglumina não altera a performance reprodutiva das mães expostas cronicamente. Estes dados sugerem que ocorre uma gradual eliminação do antimoniato de meglumina no organismo materno, sem acarretar danos a proles futuras.OBJECTIVES: Evaluate the effect of Meglumine Antimoniate on maternal-fetal transference in F1 generations (offspring of dams exposed to the drug, and embryotoxicity in F2 generations. METHODS: Female Swiss mice were treated with daily s.c. injection of Meglumine Antimoniate (100mgSb v/kg bw/day from day 7 until day 12 of pregnancy. The control group received only the vehicle (distilled water. After birth of offspring (F1

  19. 氢化物发生原子荧光法测定稻田土中的锑形态%Determination of antimony species in rice paddy soils by hydride generation atomic fluorescence spetrometry

    Institute of Scientific and Technical Information of China (English)

    郎春燕; 周英; 赖晨焕

    2012-01-01

    Antimony species in rice paddy soils in east suburb of Chengdu were determined by hydride generation-atomic fluorescence spectrometry using aqua regia as a digestant and sequential extraction method. The detection limit of Sb was 0. 108 μg/L,and the recoveries of Sb were 96. 9% ~ 104. 8%. The results showed that the interferences from Cu2+ 、Co2+ 、Se4+ 、Sn2 +、Zn2+、Pb2+、As3+ 、As5+ 、Hg2+ which possibly existed in soils could be efficiently eliminated by using the mixture of thiourea and ascorbic acid. The concentrations of antimony were in the range from 0. 92 mg/kg to 2. 52 mg/kg in samples. The average concentration was 1. 76 mg/kg. The results were not much higher than the standard concentrations of Sb in soils in SiChuan( ≈1. 70 mg/kg, 1991). In the horizontal direction, the distribution of antimony species was different due to different soil conditions of rice paddy. The concentration of antimony species in the studied rice paddy soils generally followed the direction of residual phase > organic/sulphidic phase > Fe/Mn hydrous oxides > carbonate fraction > cation exchangeable. There was a very small proportion of cation exchangeable which could be easily absorbed by plants. In the vertical direction, the concentrations of antimony species had a decreasing tendency with the increased depth of soil.%采用王水消解及逐级浸提技术,以氢化物发生-原子荧光法对成都东郊稻田土中的Sb形态进行了分析,方法检出限为0.108 μg/L,回收率为96.9%~104.8%.加入硫脲-抗坏血酸溶液后,土壤样品中可能存在的金属离子Cu2+、Co2+、Se4、Sn2+、Zn2+、pb2+、As3+、As5+、Hg2+对Sb的干扰可以有效地消除;样品Sb含量在0.92 ~2.52 mg/kg之间波动,平均值为1.76 mg/kg,与四川省土壤Sb背景浓度(≈1.70 mg/kg,1991)相比相差不大.水平方向上,各形态Sb的浓度因所处稻田条件的不同而分布各异,大体呈以下规律:残渣态>有机/硫化物结合态>铁/锰

  20. Complex dynamics

    CERN Document Server

    Carleson, Lennart

    1993-01-01

    Complex dynamics is today very much a focus of interest. Though several fine expository articles were available, by P. Blanchard and by M. Yu. Lyubich in particular, until recently there was no single source where students could find the material with proofs. For anyone in our position, gathering and organizing the material required a great deal of work going through preprints and papers and in some cases even finding a proof. We hope that the results of our efforts will be of help to others who plan to learn about complex dynamics and perhaps even lecture. Meanwhile books in the field a. re beginning to appear. The Stony Brook course notes of J. Milnor were particularly welcome and useful. Still we hope that our special emphasis on the analytic side will satisfy a need. This book is a revised and expanded version of notes based on lectures of the first author at UCLA over several \\Vinter Quarters, particularly 1986 and 1990. We owe Chris Bishop a great deal of gratitude for supervising the production of cour...

  1. Complex Systems

    Directory of Open Access Journals (Sweden)

    Yi Zhao

    2012-01-01

    Full Text Available Quantum instanton (QI approximation is recently proposed for the evaluations of the chemical reaction rate constants with use of full dimensional potential energy surfaces. Its strategy is to use the instanton mechanism and to approximate time-dependent quantum dynamics to the imaginary time propagation of the quantities of partition function. It thus incorporates the properties of the instanton idea and the quantum effect of partition function and can be applied to chemical reactions of complex systems. In this paper, we present the QI approach and its applications to several complex systems mainly done by us. The concrete systems include, (1 the reaction of H+CH4→H2+CH3, (2 the reaction of H+SiH4→H2+SiH3, (3 H diffusion on Ni(100 surface; and (4 surface-subsurface transport and interior migration for H/Ni. Available experimental and other theoretical data are also presented for the purpose of comparison.

  2. Influence of the nucleobase on the physicochemical characteristics and biological activities of Sb{sup V}-ribonucleoside complexes

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira, Claudio S.; Demicheli, Cynthia, E-mail: demichel@netuno.lcc.ufmg.b [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil). Dept. de Quimica; Rocha, Iara C.M. da; Melo, Maria N. [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil). Dept. de Parasitologia; Monte Neto, Rubens L.; Frezard, Frederic [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil). Dept. de Fisiologia e Biofisica

    2010-07-01

    The influence of the nucleobase (uracyl, U; cytosine, C; adenine, A; guanine, G) on the physicochemical characteristics and in vitro biological activities of Sb{sup V}-ribonucleoside complexes has been investigated. The 1:1 Sb-U and Sb-C complexes were characterized by NMR and ESI-MS spectroscopies and elemental analysis. The stability constant and the apparent association and dissociation rate constants of 1:1 Sb{sup V}-U, Sb{sup V}-C and Sb{sup V}-A complexes were determined. Although Sb{sup V} most probably binds via oxygen atoms to the same 2' and 3' positions in the different nucleosides, the ribose conformational changes and the physicochemical characteristics of the complex depend on the nucleobase. The nucleobase had a strong influence on the cytotoxicity against macrophages and the antileishmanial activity of the Sb{sup V}-ribonucleoside complexes. The Sb{sup V}-purine complexes were more cytotoxic and more effective against Leishmania chagasi than the Sb{sup V}-pyrimidine complexes, supporting the model that the interaction of Sb{sup V} with purine nucleosides may mediate the antileishmanial activity of pentavalent antimonial drugs. (author)

  3. Determination of trace amounts of bismuth, antimony, tellurium, cadmium, silver, tin, zinc and lead in iron and steel

    International Nuclear Information System (INIS)

    An analytical method combined AAS with the multielement extraction as quarternary amine complexes was studied to get accurate values of the 10-4 % order in the determination of Bi, Sb, Te, Cd, Ag, Sn, Zn and Pb below 50 ppm in iron and steel. In the determination of Bi, Sb, Te, Cd and Ag, 0.5 g of test portion is dissolved by heating in 10 ml of aqua regia. Nitric and hydrochloric acids are eliminated by white-fume treatment with 50 ml of sulfuric acid (1 + 3) and 2 ml of phosphoric acid (1 + 1) (In a determination of Sb, a test portion should be dissolved in 50 ml of sulfuric acid (1 + 3) to avoid the formation of Sb5+.). After cooling and diluting to 50 ml with water, the sample solution is shaked vigorously for a minute with 10 ml of the tetra-n-hexyl ammonium iodide (THAI) (0.005 M)-4-methyl-2-pentanone (MIBK) reagent to extract above five elements. Absorbance of these elements in the organic solvent is measured with an atomic absorption spectrometer and is converted into content (mass %) with working curves. In the determination of Sn, Zn and Pb, 0.5 g of test portion is dissolved by heating in 10 ml of aqua regia. Nitric and hydrochloric acids are eliminated by white-fume treatment with 3 ml of sulfuric acid (1 + 1). After cooling, 15 ml of hydrochloric acid (1 + 1) is added to dissolve the salt and Fe3+ is reduced into Fe2+ by adding 2 g of L-ascorbic acid and then the sample solution is diluted to 50 ml with water {If a determination of Pb is necessary, 10 ml of potasium iodide solution (10 g/l) is added before adding water.}. The lower limits of determination in the present method were 0.5 ppm for Cd and Ag, 2 ppm for Zn and Pb, 4 ppm for Bi, Sb and Te and 10 ppm for Sn in iron and steel. The following elements did not interfere up to 40 % Cr, 20 % Ni, 4 % of Mo and W, 2 % of Mn and Co and 1 % of Cu, V, Ti and Al. (J.P.N.)

  4. Cosmic Complexity

    Science.gov (United States)

    Mather, John C.

    2012-01-01

    What explains the extraordinary complexity of the observed universe, on all scales from quarks to the accelerating universe? My favorite explanation (which I certainty did not invent) ls that the fundamental laws of physics produce natural instability, energy flows, and chaos. Some call the result the Life Force, some note that the Earth is a living system itself (Gaia, a "tough bitch" according to Margulis), and some conclude that the observed complexity requires a supernatural explanation (of which we have many). But my dad was a statistician (of dairy cows) and he told me about cells and genes and evolution and chance when I was very small. So a scientist must look for me explanation of how nature's laws and statistics brought us into conscious existence. And how is that seemll"!gly Improbable events are actually happening a!1 the time? Well, the physicists have countless examples of natural instability, in which energy is released to power change from simplicity to complexity. One of the most common to see is that cooling water vapor below the freezing point produces snowflakes, no two alike, and all complex and beautiful. We see it often so we are not amazed. But physlc!sts have observed so many kinds of these changes from one structure to another (we call them phase transitions) that the Nobel Prize in 1992 could be awarded for understanding the mathematics of their common features. Now for a few examples of how the laws of nature produce the instabilities that lead to our own existence. First, the Big Bang (what an insufficient name!) apparently came from an instability, in which the "false vacuum" eventually decayed into the ordinary vacuum we have today, plus the most fundamental particles we know, the quarks and leptons. So the universe as a whole started with an instability. Then, a great expansion and cooling happened, and the loose quarks, finding themselves unstable too, bound themselves together into today's less elementary particles like protons and

  5. Cosmic Complexity

    Science.gov (United States)

    Mather, John C.

    2012-01-01

    What explains the extraordinary complexity of the observed universe, on all scales from quarks to the accelerating universe? My favorite explanation (which I certainty did not invent) ls that the fundamental laws of physics produce natural instability, energy flows, and chaos. Some call the result the Life Force, some note that the Earth is a living system itself (Gaia, a "tough bitch" according to Margulis), and some conclude that the observed complexity requires a supernatural explanation (of which we have many). But my dad was a statistician (of dairy cows) and he told me about cells and genes and evolution and chance when I was very small. So a scientist must look for me explanation of how nature's laws and statistics brought us into conscious existence. And how is that seemll"!gly Improbable events are actually happening a!1 the time? Well, the physicists have countless examples of natural instability, in which energy is released to power change from simplicity to complexity. One of the most common to see is that cooling water vapor below the freezing point produces snowflakes, no two alike, and all complex and beautiful. We see it often so we are not amazed. But physlc!sts have observed so many kinds of these changes from one structure to another (we call them phase transitions) that the Nobel Prize in 1992 could be awarded for understanding the mathematics of their common features. Now for a few examples of how the laws of nature produce the instabilities that lead to our own existence. First, the Big Bang (what an insufficient name!) apparently came from an instability, in which the "false vacuum" eventually decayed into the ordinary vacuum we have today, plus the most fundamental particles we know, the quarks and leptons. So the universe as a whole started with an instability. Then, a great expansion and cooling happened, and the loose quarks, finding themselves unstable too, bound themselves together into today's less elementary particles like protons and

  6. Tailoring the Valence Band Offset of Al2O3 on Epitaxial GaAs(1-y)Sb(y) with Tunable Antimony Composition.

    Science.gov (United States)

    Liu, Jheng-Sin; Clavel, Michael; Hudait, Mantu K

    2015-12-30

    Mixed-anion, GaAs1-ySby metamorphic materials with tunable antimony (Sb) compositions extending from 0 to 100%, grown by solid source molecular beam epitaxy (MBE), were used to investigate the evolution of interfacial chemistry under different passivation conditions. X-ray photoelectron spectroscopy (XPS) was used to determine the change in chemical state progression as a function of surface preclean and passivation, as well as the valence band offsets, conduction band offsets, energy band parameters, and bandgap of atomic layer deposited Al2O3 on GaAs1-ySby for the first time, which is further corroborated by X-ray analysis and cross-sectional transmission electron microscopy. Detailed XPS analysis revealed that the near midpoint composition, GaAs0.45Sb0.55, passivation scheme exhibits a GaAs-like surface, and that precleaning by HCl and (NH4)2S passivation are mandatory to remove native oxides from the surface of GaAsSb. The valence band offsets, ΔEv, were determined from the difference in the core level to the valence band maximum binding energy of GaAs1-ySby. A valence band offset of >2 eV for all Sb compositions was found, indicating the potential of utilizing Al2O3 on GaAs1-ySby (0 ≤ y ≤ 1) for p-type metal-oxide-semiconductor (MOS) applications. Moreover, Al2O3 showed conduction band offset of ∼2 eV on GaAs1-ySby (0 ≤ y ≤ 1), suggesting Al2O3 dielectric can also be used for n-type MOS applications. The surface passivation of GaAs0.45Sb0.55 materials and the detailed band alignment analysis of Al2O3 high-κ dielectrics on tunable Sb composition, GaAs1-ySby materials, provides a pathway to utilize GaAsSb materials in future microelectronic and optoelectronic applications. PMID:26642121

  7. Complex silumins

    Directory of Open Access Journals (Sweden)

    S. Pietrowski

    2007-09-01

    Full Text Available Purpose: The study presents the results of investigations carried out on silumins with additions of Mg, Ni, Cu, Cr, Mo and W. The silumins containing Mg, Cu and Ni are well-known and commonly used in construction of machines and equipment.Design/methodology/approach: Additions of Cr, Mo and W have not been thoroughly investigated yet. They are considered a new family of innovative cast aluminium alloys.Findings: In Al-Si systems they form silicides, like Cr3Si, Mo3Si, W3Si and intermetallic phases of Al13Cr4Si4, Al12Mo, Al12W and AlWSi. The silicides crystallise in cubic lattice of parameters similar to aluminium and silicon.Research limitations/implications: Therefore they can act as crystallisation substrates and occur as separate phases. The examinations under the microscope and X-ray microanalysis of the linear and point distribution of elements confirmed the presence of the above mentioned phases. A combination of two elements, e.g. Cr and Mo, or Cr and W, was observed to cause the formation of complex silicide layers of Mo3Si and (Cr, Mo3Si, or Cr3Si as well as (W, Cr3Si.Originality/value: The presence of the silicides has been indicated as a possible source of the refinement of α(Al and β(Si phases. The precipitations of these phases and of the intermetallic phases favour a high degree of the silumins hardening. A characteristic feature is the fact that nucleation and crystallisation of the successive phases takes place at the phase boundaries formed between the previously precipitated phase and solid solution α. The studies carried out so far have indicated that in complex silumins at high temperatures crystallise the silicides and peritectic phases of Al12W, AlWSi, Al12Mo and Al13Cr4Si4. Phases α or β are the next ones to crystallise, followed by complex eutectic α + β +Al(Si, Cr, Mo, W, Fe. Further crystallise the phases of Mg2Si, Al3Ni and Al2Cu. The silumins presented here are characterised by high mechanical properties: Rp0

  8. Anion-Controlled Positional Switching of a Phenyl Group about the Dinuclear Core of a AuSb Complex.

    Science.gov (United States)

    Sen, Srobona; Ke, Iou-Sheng; Gabbaï, François P

    2016-09-19

    As part of our continuing interest in redox-active, anion-responsive main-group transition-metal platforms, we have investigated the effect of chloride by fluoride anion substitution on the core structure of a dinuclear AuSb platform. Starting from [(o-(iPr2P)C6H4)2Cl2SbPh]AuCl (2) in which the antimony-bound phenyl group is positioned trans to the gold atom, we found that the introduction of fluoride anions, as in [(o-(iPr2P)C6H4)2F2SbPh]AuCl (3) and [(o-(iPr2P)C6H4)2ClFSbPh]AuCl (4), produces structures in which the phenyl group switches to a perpendicular direction with respect to the gold atom. Replacement of the gold-bound chloride anion in 3 by a fluoride anion can be achieved by successive treatment with TlPF6 and [nBu4N][Ph3SiF2]. These reactions, which proceed via the intermediate zwitterionc gold antimonate complex [o-(iPr2P)C6H4)2F3SbPh]Au (6), trigger migration of the phenyl group to gold and afford [(o-(iPr2P)C6H4)2F3Sb]AuPh (7). Because the phenyl group in 7 is orthogonal to that in 3 and opposite to that in 2, the title AuSb platform can be regarded as a molecular analogue of a mechanical three-way switch in which the switching element is a phenyl group. Finally, while all complexes involved retain a Au → Sb interaction, this interaction is no longer present in the zwitterionic derivative 6 because of the neutralization of the Lewis acidity of the antimony center. PMID:27583565

  9. Biomonitoring of persons living in areas with high concentrations of mercury, arsenic and antimony in soil. Goals and methods; Biomonitoring-Untersuchung bei Personen in Wohngebieten mit erhoehten Bodenwerten an Quecksilber, Arsen und Antimon. Vorstellung und Studiendesign

    Energy Technology Data Exchange (ETDEWEB)

    Gebel, T. [Goettingen Univ. (Germany). Abt. Allgemeine Hygiene; Schaefer, J. [Mainz Univ. (Germany). Inst. fuer Medizinische Mikrobiologie und Hygiene; Beuermann, I. [Mainz Univ. (Germany). Inst. fuer Medizinische Mikrobiologie und Hygiene; Platen, H. von [Mainz Univ. (Germany). Inst. fuer Geowissenschaften; Dunkelberg, H. [Goettingen Univ. (Germany). Abt. Allgemeine Hygiene

    1995-07-01

    In the northern part of palatinate country in Germany (Nordpfaelzer Bergland; Rheinland-Pfalz) intense mercury activity had been situated beginning in the 15th century extending partly up into the 20th century. Nowadays in many cases former dump grounds of rubble caused by the mercury mining activities are used for agricultural and housing purposes. In soil material of these areas the natural background contents up to strongly elevated levels were found for mercury, arsenic and antimony. In the housing area soil concentrations (per dry matter) of less than 0,5 mg/kg up to 1364 mg/kg mercury, less than 2 mg/kg up to 605 mg/kg arsenic and less than 0,5 mg/kg up to 776 mg/kg antimony were detected. Mercury, arsenic and antimony are strongly bound to be ore in sulfidic forms of cinnabar or fahlore (gray copper) causing a bad availability. The concentration variance of the detected element levels is immense even relating to little spaces because of an inhomogenous distribution of the rubble; highly contaminated grounds can be found beneath not contaminated ground. A biomonitoring study is presented in which 219 exposed residents are involved. They are examined concerning a possible incorporation of the elements mentioned above. The proceeding of the study, the way of data collection, and the amnestical approach are discussed. This study ist compared to similar studies. (orig.) [Deutsch] Im Nordpfaelzer Bergland wurde vom 15. bis teilweise ins 20. Jahrhundert intensiv Quecksilberbergbau betrieben. Vielfach befinden sich landwirtschaftlich genutzte Flaechen und Wohngebiete auf oder neben Abraumhalden des ehemaligen Quecksilberbergbaus. In diesen Regionen fand man im Boden fuer das Schwermetall Quecksilber und die metalloide Arsen und Antimon von den natuerlichen Hintergrundkonzentrationen bis hin zu stark erhoehten Werten. In Wohngebieten waren dies bei Quecksilber weniger als 0,5 mg/kg Boden (Trockensubstanz) bis zu 1364 mg/kg, bei Arsen weniger als 2 mg/kg bis zu 605 mg

  10. Determination of trace amount of antimony (Ⅲ) by adsorption voltammetry on carbon paste electrode%碳糊电极吸附伏安法测定痕量锑

    Institute of Scientific and Technical Information of China (English)

    郭会时; 肖鹏峰; 聂立波; 李益恒; 何农跃

    2004-01-01

    根据锑与溴邻苯三酚红(BPR)生成的络合物在碳糊电极上的吸附特性, 建立了测定痕量锑的吸附伏安法. 整个分析过程分3个步骤: 吸附富集、还原和溶出. 用单因素变化法得出最佳试验条件为: 以含40 μmol/L BPR的0.10mol/L HCl为富集底液; 富集时间150 s; 还原和溶出介质为0.20mol/L HCl; 还原电位为-0.50V; 还原时间为60 s;扫描范围为-0.5~0.20V. 考察了共存离子的影响. 二次导数溶出峰电流与锑(Ⅲ)浓度在1. 0nmol/L~0. 50μmol/L范围内呈良好的线性关系, 检出限达0.5nmol/L. 该方法已成功应用于人发和水样中锑的测定.%A sensitive method is described for the determination of trace antimony based on the antimony-bromopyrogallol red (BPR) adsorption at a carbon paste electrode (CPE). Three steps were involved in the overall analysis: preconcentration, reduction and stripping. Optimal conditions were found to be an electrode containing 25% paraffin oil and 75% high purity graphite powder as working electrode; a 0. 10mol/L HCl solution containing 40 μmol/L BPR as accumulation medium; a 0. 20mol/L HCl solution as reduction and stripping electrolyte; accumulation time, 150 s; reduction potential and time, -0. 50 V, 60 s; scan range from -0. 50 to 0. 20V. Interferences by other ions were studied as well. The detection limit was found to be 0. 5nmol/L for 150 s preconcentration. The linear range was from 1. 0nmol/L to 0. 50 μmol/L. Application of the proposed method to the determination of antimony in water and human hair samples gave good results.

  11. Determination of Arsenic and Antimony in Leather by Atomic Fluorescence Spectrometry with Microwave Digestion%微波消解—原子荧光光谱法同时测定皮革中的砷和锑

    Institute of Scientific and Technical Information of China (English)

    吕小园; 陈新焕; 肖家勇; 刘正华; 陈练; 杨万彪; 黄红; 张志荣

    2012-01-01

    建立了皮革及其制品中砷和锑的微波消解-原子荧光光谱测定方法,方法准确、灵敏,快速.在优化的试验条件下,砷浓度在0.5~150 ng/mL范围内成线性关系,相关系数r=0.9995,检出限为0.22 ng/mL,回收率为99.4%~104.2%:锑浓度在0.5~ 120 ng/mL范围内成线性关系,相关系数r=0.9998,检出限为0.16 ng/mL,回收率为101.1%~106.7%.相对标准偏差(n=5)均小于5%.方法应用于皮革及其制品中砷和锑的测定,结果满意.%An accurate, sensitive and quick method for determination of arsenic and antimony in leather by atomic fluorescence spectrometry with microwave digestion was developed in this paper. Under the optimized condition, the result of arsenic showed that the linear range was 0.5 - 150 ng/mL(r =0. 9995), the limit of detection was 0. 22 ng/mL, and the average recoveries in leather ranged form 99. 4% to 104. 2% . The linear range of antimony was 0. 5 ~ 120 ng/mL( r = 0.9998) , the limit of detection was 0. 16 ng/mL, the average recoveries ranged form 101. 1% tol06.7%. TheRSD(n=5) were all lower than 5%. It has been applied to routine determination of arsenic and antimony in leather with satisfactory results.

  12. Assessment of femoral head vascularity by technetium-99m antimony colloid bone marrow imaging within 24 hours of subcapital fracture: a prospective study of 30 patients followed for 2 years

    International Nuclear Information System (INIS)

    The rationale of preoperative imaging of bone marrow was based upon the demonstration of histochemical abnormalities secondary to ischaemia which first become apparent in marrow cells of the femoral head following interruption of the blood supply by subcapital fracture. These marrow abnormalities predate changes in bone cells by several days and may explain the absence of abnormality on conventional bone scans performed on avascular femoral heads within 24 hours of subcapital fracture. The use of an endoprosthesis for fresh femoral neck fractures in unselected patients results in high mortality, high infection rate, high incidence of thromboembolic disease and poor long term results. The successful prediction of avascular necrosis in 92% of 28 patients with active bone marrow in the femoral head in this study is sufficiently accurate to allow appropriate selection of patients for internal fixation or primary prosthetic replacement on the basis of preoperative Tc-99m antimony colloid imaging

  13. Oxygen 17 NMR in the evaluation of oxygen bounding with central ion using hydrolysis products of niobium, tantalum, arsenic, antimony pentafluorides as an example. Symbasis in the change of 17O and 19F chemical shifts

    International Nuclear Information System (INIS)

    Hydrolysis products of niobium, tantalum, antimony and arsenic pentafluorides in acetonitrile solution were studied by the methods of 17O and 19F NMR. In 17O NMR spectra of niobium and tantalum pentafluorides hydrolysis products resonance signals of oxo-, hydroxo- and aquafluorocomplexes were defined. Considerable shift of 17O NMR resonance signals towards weak field making up about 300 m.p., may indicate a higher covalency (Π-character) of Nb-O bond compared to Ta-O one. Symbasis in the change of chemical shifts in 17O NMR and 19F NMR of the relevant hexafluorides and hydrolysis products was detected implying similarity of chemical bond nature in oxygen and fluorine

  14. Development and application of double membrane modified antimony pH electrode and its testing instrument%双层膜锑pH电极及其测试仪的研制与应用

    Institute of Scientific and Technical Information of China (English)

    盛庆元; 张西良; 李萍萍; 刘丽晨; 陈书田

    2013-01-01

    The value of pH is a key chemical parameter in the field of industrial and agricultural production, medicine, environmental protection and other fields. At present, commercial glass pH electrodes have been widely used in soil pH test in the laboratory due to its convenience and reliability. But with turbid and vibrate systems in the filed like on-the-go pH mapping, glass electrode cannot be used because of its brittleness of the glass membrane, sluggish response, which are difficult to miniaturize and planarize based on current manufacturing technologies. In this work, a simple, flexible, inexpensive and effective way to make bilayer membrane modified antimony pH electrode was presented and one pH tester was developed. The surface of the obtained antimony wire was oxidized in sodium dioxide melt to fabricate an antimony oxide film for pH sensing as first layer. The second layer was Nafion membrane with selective characteristics, which was coated after the first layer. The sensing response and open-circuit potential of the electrode had a good linear relationship (R2=0.997) with pH value in the test solution, which also exhibited small hysteresis, fast response than that of bare antimony pH electrode. The open-circuit potential of the electrode was almost drift-free, with an average variation as small as 0.1mV over an hour. Ion interference experiment showed that this electrode has good selectivity with common ions (Na+, K+, Ca2+, Cl-, Br-) in soil, redox ion([Fe(CN)6]3-, [Fe(CN)6]4-) and citrate ions ( C6H5O73-). The bilayer membrane modified antimony pH electrode and the Ag/AgCl reference electrode as sensor were employed to pH tester, which was designed based on 16 bit low power consumption microcontroller (Sunplus SPCE061A). Tester readings in soil turbid solution under controlled in the lab were compared with the data obtained by standard protocols of soil. The tests demonstrated a high degree of linearity between standard laboratory values and turbid soil

  15. Measuring Tax Complexity

    OpenAIRE

    David Ulph

    2014-01-01

    This paper critically examines a number of issues relating to the measurement of tax complexity. It starts with an analysis of the concept of tax complexity, distinguishing tax design complexity and operational complexity. It considers the consequences/costs of complexity, and then examines the rationale for measuring complexity. Finally it applies the analysis to an examination of an index of complexity developed by the UK Office of Tax Simplification (OTS). Postprint

  16. On State Complexes and Special Cube Complexes

    Science.gov (United States)

    Peterson, Valerie J.

    2009-01-01

    This thesis presents the first steps toward a classification of non-positively curved cube complexes called state complexes. A "state complex" is a configuration space for a "reconfigurable system," i.e., an abstract system in which local movements occur in some discrete manner. Reconfigurable systems can be used to describe, for example,…

  17. Pricing complexity options

    OpenAIRE

    Malihe Alikhani; Bj{\\o}rn Kjos-Hanssen; Amirarsalan Pakravan; Babak Saadat

    2015-01-01

    We consider options that pay the complexity deficiency of a sequence of up and down ticks of a stock upon exercise. We study the price of European and American versions of this option numerically for automatic complexity, and theoretically for Kolmogorov complexity. We also consider run complexity, which is a restricted form of automatic complexity.

  18. Effect of Halogen-antimony Flame Retardant System on Thermoplastic Polyester Elastomer%卤-锑阻燃体系对热塑性聚酯弹性体性能的影响

    Institute of Scientific and Technical Information of China (English)

    奚溪; 张群朝; 赵辉; 蒋涛

    2013-01-01

      采用高分子型溴系阻燃剂溴化环氧树脂(EP-B)、溴化聚苯乙烯(PS-B)及小分子型溴系阻燃剂十溴二苯乙烷(DBDPE)协同Sb2O3作为卤–锑阻燃体系,研究卤–锑阻燃体系对热塑性聚酯弹性体(TPEE)性能的影响。研究表明,当溴系阻燃剂的质量分数为18%时,均能使TPEE达到UL94 V–0级别,极限氧指数达到27%以上,EP-B, PS-B分别与DBDPE复配使用时的阻燃效果优于EP-B,PS-B单独使用时的阻燃效果;EP-B和PS-B与TPEE具有较好的相容性,两者分别与DBDPE复配时可改善DBDPE与TPEE的相容性;当溴系阻燃剂的质量分数为18%时, EP-B和PS-B分别与DBDPE复配使用,可减少单独使用DBDPE阻燃TPEE力学性能的下降程度;添加阻燃剂改变了TPEE的热失重过程,与EP-B,PS-B阻燃TPEE的残炭率相比,两者分别与DBDPE复配后,阻燃TPEE的残炭率下降约20%。%  With two polymeric brominated flame retardants brominated epoxy resin(EP-B) and brominated polystyrene(PS-B) and a new type of low molecular weight brominated flame retardant decabromodiphenyl ethane(DBDPE) synchronized with antimony trioxide(Sb2O3) respectively as three halogen–antimony flame retardant systems,the effects of halogen–antimony flame retardant systems on thermoplastic polyester elastomer(TPEE) were discussed. The results show that when the mass fraction of brominated flame retardants is 18%,UL94 vertical burning of TPEE could reach V–0 level,the limit oxygen index could reach more than 27%,when EP-B and PS-B were compound with DBDPE respectively,the flame retardant efficiencies are better than that of the systems when they were used in TPEE alone. EP-B and PS-B had preferable compatibility with TPEE,when they were compound with DBDPE,the compatibility of DBDPE and TPEE could be improved. When the mass fraction of brominated flame retardants is 18%,EP-B and PS-B were compound with DBDPE respectively,the decline degree of

  19. 某锑金矿综合回收锑、金的试验研究%Comprehensive Recovery of Au and Sb from an Antimony-gold Concentrate

    Institute of Scientific and Technical Information of China (English)

    杨永斌; 刘波; 李骞; 姜涛

    2014-01-01

    采用酸法浸锑⁃浸锑渣焙烧脱硫⁃氰化浸金工艺从某锑金精矿中分离提取锑、金。酸法浸锑最佳工艺条件为:温度为95℃、[H+]=4 mol/L、液固比为4∶1、FeCl3过量系数为1.1、浸出时间为0.5 h,在此条件下,锑浸出率为99.05%,进入浸锑液的金仅为0.99%,实现了锑、金良好的选择性浸出。对浸锑渣直接氰化浸金,浸金率仅为71.93%。为了提高浸金率,在分析酸性浸锑渣的矿物组成的基础上,对浸锑渣进行氧化焙烧,结果表明:碚砂中硫品位仅为0.18%,硫脱除率达到了99.81%,渣中的单质硫及硫化物显著减少,主要以赤铁矿和脉石矿物为主。最终金浸出率达到95.92%,比浸锑渣直接氰化浸金提高了约24个百分点。%Comprehensive recovery of Sb and Au from an antimony⁃gold concentrate is studied by adopting a process of Sb leaching with acid solution⁃oxidizing roasting of the antimony residue⁃cyanide leaching of gold. Under the following optimum conditions, that is, leaching at 95℃ for 0.5 h with HCl concentration at 4.0 mol/L, liquid⁃solid rate at 4∶1, excess coefficient of FeCl3 being 1. 1, a favorable selective leaching effect can be realized for Sb and Au, with the leaching rate of Sb up to 99.05% and only 0.99% Au recovered into antimony leachate. However, the following direct cyanide leaching only resulted in the Au leaching rate of 71.93%. For the purpose of increasing the leaching rate of Au, the antimony leaching residue was subjected to oxidizing roasting process based on the analysis of its mineral compositions, leading to only 0.18%S in the calcined product, with removal rate of sulfur up to 99.81%. It is found that hematite and gangue minerals are the dominant minerals in the residue, with the content of sulfur and sulfide remarkably decreased. The ultimate leaching rate of Au reached 95. 92%, 24 percentage points higher than that by direct

  20. 湿法生产锑白渣中硫磺的回收工艺%Reclaiming technology of sulphur from leaching residue of antimony white with hydrometallurgical process

    Institute of Scientific and Technical Information of China (English)

    王文侠

    2012-01-01

    A sulphur reclaiming method from leaching residue of antimony white with hydrometallurgical process was introduced. Ammonia sulfide solution was selected as extracted liquor,and sulphur in leaching residue could form polysulfide ions, which will dissolve in the solution.The filtrate was separated out through suction filtration and the thermal decomposition was carried out.The produced gas was led out and absorbed, which can be used circularly.Finally, sulphur product could be prepared through thermal decomposition of filtrate.The best extraction conditions included the ratio of solid to liquid of 1:20, leaching time of 2 h,and leaching temperature of 20 t.The process had many advantages,such as equipment,technology, and sulphur extracting operation were very simple,the extract liquid could be returned for recycling,the cost was lower, the quality of the sulphur products was good,and the total sulphur recovery could reach over 99%.At the same time,the waste residue of antimony prodcution was recycled and utilized comprehensively, so that the pollution of the environment and the pile-up of waste residue could be reduced.%介绍了一种从湿法生产锑白渣中回收硫磺的方法.以硫化铵溶液作为提取液浸取矿渣,矿渣中的硫可生成多硫离子而溶解转入溶液中,抽滤分离出滤液,将产生的气体导出并吸收,吸收后可返回循环使用;滤液热分解后可得到硫磺产品.最佳提取条件:固液比为1:20、浸取温度为20℃、浸取时间为2 h.该工艺设备及提硫操作简单,硫化铵可循环利用,成本较低,硫磺产品的质量较好,硫的总回收率可达99%以上.同时利用了浸锑废渣,实现资源 综合回收利用,又减少环境污染和废渣的堆积量.

  1. 砷、锑、铋的氨荒酸类配合物的研究进展%Research Progress on Chemistry of Arsenic, Antimony and Bismuth Complexes with Dithiocarbamate

    Institute of Scientific and Technical Information of China (English)

    张志朋; 宋玉侠

    2013-01-01

    综述了近年来合成的三价和五价砷、锑、铋的氨荒酸配合物,包括均配、非均配氨荒酸配体配合物等,在这些配合物中观察到了结构的多样性和不同的成键方式,并对其合成、特性、应用等方面进行了介绍,并对其进行了展望.

  2. Complex Multiplicative Calculus

    OpenAIRE

    Bashirov, Agamirza; Riza, Mustafa

    2011-01-01

    In the present paper we extend the concepts of multiplicative de- rivative and integral to complex-valued functions of complex variable. Some drawbacks, arising with these concepts in the real case, are explained satis- factorily. Properties of complex multiplicative derivatives and integrals are studied. In particular, the fundamental theorem of complex multiplicative calculus, relating these concepts, is proved. It is shown that complex multi- plicative calculus is not just another realizat...

  3. Second Quantized Kolmogorov Complexity

    OpenAIRE

    Rogers, Caroline; Vedral, Vlatko; Nagarajan, Rajagopal

    2008-01-01

    The Kolmogorov complexity of a string is the length of its shortest description. We define a second quantised Kolmogorov complexity where the length of a description is defined to be the average length of its superposition. We discuss this complexity's basic properties. We define the corresponding prefix complexity and show that the inequalities obeyed by this prefix complexity are also obeyed by von Neumann entropy.

  4. Complex networks analysis of language complexity

    CERN Document Server

    Amancio, Diego R; Oliveira, Osvaldo N; Costa, Luciano da F; 10.1209/0295-5075/100/58002

    2013-01-01

    Methods from statistical physics, such as those involving complex networks, have been increasingly used in quantitative analysis of linguistic phenomena. In this paper, we represented pieces of text with different levels of simplification in co-occurrence networks and found that topological regularity correlated negatively with textual complexity. Furthermore, in less complex texts the distance between concepts, represented as nodes, tended to decrease. The complex networks metrics were treated with multivariate pattern recognition techniques, which allowed us to distinguish between original texts and their simplified versions. For each original text, two simplified versions were generated manually with increasing number of simplification operations. As expected, distinction was easier for the strongly simplified versions, where the most relevant metrics were node strength, shortest paths and diversity. Also, the discrimination of complex texts was improved with higher hierarchical network metrics, thus point...

  5. Structure of PbSb/sub 2/O/sub 6/ and its relationship to the crystal chemistry of PbO/sub 2/ in antimonial lead-acid batteries

    Energy Technology Data Exchange (ETDEWEB)

    Hill, R.J.

    1987-11-01

    The crystal structure of PbSb/sub 2/)/sub 6/, space group P anti 31m, a = 5.3006(1), c = 5.3792(1) A, V = 130.89(2) A, Z = 1, D/sub x/ = 6.936 g cm/sup -3/, has been refined at 295 K by Rietveld analysis of step-scan neutron powder diffraction data (lambda = 1.500 A, ..mu.. 0.179 cm/sup -1/): R/sub wp/ = 0.0614 for 2898 step intensities, R/sub B/ = 0.0141 for 150 reflections. The structure consists of gibbsitelike sheets of edge-sharing SbO/sub 6/ octahedra oriented perpendicular to the c-axis. These sheets alternate with layers of isolated PbO/sub 6/ octahedra positioned above and below the vacant sites in the adjacent (SbO/sub 6/)/sup 2 -/ layers. The SbO/sub 6/ octahedra have symmetry 32 and a bond length of 1.9904(4) A; the PbO/sub 6/ octahedra have symmetry anti 3m and a bond length of 2.5633(6) A. The properties of this structure and its relationship to the polymorphs of PbO/sub 2/ provide possible explanations for the well-known beneficial effect of antimony on the cycle life of lead-acid batteries.

  6. Enhancement of the superconducting transition temperature and upper critical field of LaO{sub 0.8}F{sub 0.2}FeAs with antimony doping

    Energy Technology Data Exchange (ETDEWEB)

    Singh, S J; Patnaik, S [School of Physical Sciences, Jawaharlal Nehru University, New Delhi 110067 (India); Prakash, J; Ganguli, A K [Department of Chemistry, Indian Institute of Technology, New Delhi 110016 (India)], E-mail: spatnaik@mail.jnu.ac.in, E-mail: ashok@chemistry.iitd.ernet.in

    2009-04-15

    We report the synthesis and characterization of the antimony-doped oxypnictide superconductor, LaO{sub 0.8}F{sub 0.2}FeAs{sub 1-x}Sb{sub x} (x = 0.05 and 0.10). The parent compound LaOFeAs with fluorine doping exhibits superconductivity at the maximum transition temperature {approx}28.5 K (at ambient pressure). Here we partially substitute As by Sb (LaO{sub 0.8}F{sub 0.2}FeAs{sub 1-x}Sb{sub x}) and observe enhancement of the transition temperature to 30.1 K. This is one rare case where T{sub c} increases with doping in the conducting layer (FeAs) and this leads to the highest transition temperature in any La-based oxypnictide. X-ray diffraction and energy-dispersive x-ray analysis measurements confirm the phase purity of the samples and the presence of Sb. The magneto-resistance measurements show that the value of the upper critical field H{sub c2}(0) is about 73 T, corresponding to a coherence length ({xi}{sub GL}) of 22 A. The Seebeck coefficient measurements indicate electron transport with a strong contribution from electron-electron correlation. These results provide interesting insight into the origin of superconductivity in this novel series of compounds.

  7. 锑精炼除铅渣硝酸浸出回收铅的研究%Study on Lead Recovery from Lead Slag of Antimony Refining by Nitric Acid Leaching Process

    Institute of Scientific and Technical Information of China (English)

    韦岩松; 盘有旺

    2013-01-01

    采用硝酸浸出的方法从锑精炼除铅渣中回收金属铅,考察了液固比、浸出温度和时间、硝酸浓度等对铅浸出率的影响.结果表明,适宜的浸出工艺为:液固比4、浸出温度80℃、浸出时间50 min、硝酸浓度7.0 mol/L.在此条件下,铅浸出率可以达到94%.%Lead was recovered from lead slag of antimony refining by nitric acid leaching process.The effects of ratio of liquid to solid (L/S),leaching temperature and time,and nitric acid concentration on lead leaching rate were investigated.The results show that the lead leaching rate is above 94% under the optimum conditions including L/S of 4,leaching temperature of 80 ℃,leaching time of 50 min,and nitric acid concentration of 7.0 mol/L.

  8. Establishing the Coordination Chemistry of Antimony(V) Cations: Systematic Assessment of Ph4 Sb(OTf) and Ph3 Sb(OTf)2 as Lewis Acceptors.

    Science.gov (United States)

    Robertson, Alasdair P M; Chitnis, Saurabh S; Jenkins, Hilary A; McDonald, Robert; Ferguson, Michael J; Burford, Neil

    2015-05-18

    The coordination chemistry of the stiboranes Ph4 Sb(OTf) (1 a, OTf = OSO2 CF3 ) and Ph3 Sb(OTf)2 (3) with Lewis bases has been investigated. The significant steric encumbrance of the Sb center in 1 a precludes interaction with most ligands, but the relatively low steric demands of 4-methylpyridine-N-oxide (OPyrMe) and OPMe3 enabled the characterization of [Ph4 Sb(OPyrMe)][OTf] (2 a) and [Ph4 Sb(OPMe3 )][OTf] (2 b), rare examples of structurally characterized complexes of stibonium acceptors. In contrast, 3 was found to engage a variety of Lewis bases, forming stable isolable complexes of the form [Ph3 Sb(donor)2 ][OTf]2 [donor=OPMe3 (6 a), OPCy3 (6 b, Cy=cyclohexyl), OPPh3 (6 c), OPyrMe (6 d)], [Ph3 Sb(dmap)2 (OTf)][OTf] (6 e, dmap=4-(dimethylamino)pyridine) and [Ph3 Sb(donor)(OTf)][OTf] [donor=1,10-phenanthroline (7 a) or 2,2'-bipy (7 b, bipy=bipyridine)]. These compounds exhibit significant structural diversity in the solid-state, and undergo ligand exchange reactions in line with their assignment as coordination complexes. Compound 3 did not form stable complexes with phosphine donors, with reactions instead leading to redox processes yielding SbPh3 and products of phosphine oxidation.

  9. Irinotecan Lipid Complex Injection

    Science.gov (United States)

    Irinotecan lipid complex is used in combination with other medications to treat pancreatic cancer that has spread to other ... worsened after treatment with other chemotherapy medications. Irinotecan lipid complex is in a class of antineoplastic medications ...

  10. Doxorubicin Lipid Complex Injection

    Science.gov (United States)

    Doxorubicin lipid complex is used to treat ovarian cancer that has not improved or that has worsened after treatment with other medications. Doxorubicin lipid complex is also used to treat Kaposi's sarcoma ( ...

  11. Vincristine Lipid Complex Injection

    Science.gov (United States)

    Vincristine lipid complex is used to treat a certain type of acute lymphoblastic leukemia (ALL; a type of cancer ... least two different treatments with other medications. Vincristine lipid complex is in a class of medications called ...

  12. Complexity An Introduction

    CERN Document Server

    Parwani, R R

    2002-01-01

    This article summarises a Web-book on "Complexity" that was developed to introduce undergraduate students to interesting complex systems in the biological, physical and social sciences, and the common tools, principles and concepts used for their study.

  13. Curve complexes are rigid

    OpenAIRE

    Rafi, Kasra; Schleimer, Saul

    2007-01-01

    Any quasi-isometry of the complex of curves is bounded distance from a simplicial automorphism. As a consequence, the quasi-isometry type of the curve complex determines the homeomorphism type of the surface.

  14. Quantum Communication Complexity

    OpenAIRE

    Klauck, Hartmut

    2000-01-01

    This paper surveys the field of quantum communication complexity. Some interesting recent results are collected concerning relations to classical communication, lower bound methods, one-way communication, and applications of quantum communication complexity.

  15. Oligocyclopentadienyl transition metal complexes

    Energy Technology Data Exchange (ETDEWEB)

    de Azevedo, Cristina G.; Vollhardt, K. Peter C.

    2002-01-18

    Synthesis, characterization, and reactivity studies of oligocyclopentadienyl transition metal complexes, namely those of fulvalene, tercyclopentadienyl, quatercyclopentadienyl, and pentacyclopentadienyl(cyclopentadienyl) are the subject of this account. Thermal-, photo-, and redox chemistries of homo- and heteropolynuclear complexes are described.

  16. Complexity and Dynamical Depth

    OpenAIRE

    Terrence Deacon; Spyridon Koutroufinis

    2014-01-01

    We argue that a critical difference distinguishing machines from organisms and computers from brains is not complexity in a structural sense, but a difference in dynamical organization that is not well accounted for by current complexity measures. We propose a measure of the complexity of a system that is largely orthogonal to computational, information theoretic, or thermodynamic conceptions of structural complexity. What we call a system’s dynamical depth is a separate dimension of system c...

  17. Complexity Near Horizons

    CERN Document Server

    Halyo, Edi

    2015-01-01

    We generalize the concept of complexity near horizons to all nondegenerate black holes. For Schwarzschild black holes, we show that Rindler observers see a complexity change of $S$ during proper time $1/\\kappa$ which corresponds to the creation of a causal patch with proper length $1/\\kappa$ inside the horizon. We attempt to describe complexity in the horizon CFT and the Euclidean picture.

  18. Complex variables I essentials

    CERN Document Server

    Solomon, Alan D

    2013-01-01

    REA's Essentials provide quick and easy access to critical information in a variety of different fields, ranging from the most basic to the most advanced. As its name implies, these concise, comprehensive study guides summarize the essentials of the field covered. Essentials are helpful when preparing for exams, doing homework and will remain a lasting reference source for students, teachers, and professionals. Complex Variables I includes functions of a complex variable, elementary complex functions, integrals of complex functions in the complex plane, sequences and series, and poles and r

  19. SYSTEMS WITH COMPLEXITY

    Institute of Scientific and Technical Information of China (English)

    WANG Chenghong; ZHANG Lijun

    2004-01-01

    Science of Complexity is a newly emerging branch of natural scienceAlthoughwe still haven't a precise definition, there are some principles for justifying whether a systemis a complex systemThe purpose of this article is to reveal some of such principlesOnthe basis of them, the concept of a system with complexity is proposedThey may helpus to distinguish a real complex system from complicated objects in common senseThenwe propose some fundamental problems faced by the study of systems with complexity.

  20. Experimental research on the improvement of gold recovery rate applying alkaline leaching pretreatment of a refractory arsenic and antimony contained gold concentrate%碱浸预处理提高某含砷锑难处理金精矿回收率的试验研究

    Institute of Scientific and Technical Information of China (English)

    李勇; 徐忠敏; 吕翠翠; 张治磊

    2013-01-01

    内蒙古某黄金矿山金精矿中,金主要包裹在黄铁矿及砷黄铁矿中,同时还有锑金属硫化物的存在.氰化浸出生产工艺中金的回收率比较低,只有76.63%.通过常规氰化工艺条件优化试验,金的回收率最高可达到80.15%.对该低品位含砷、锑难处理金精矿进行碱浸预处理,优先除砷、锑,以提高金氰化浸出率.确定了生产操作的最佳工艺条件,金的氰化回收率由原来的76.63%提高到92%,试验获得了较好技术指标和经济效益.%Gold in the gold concentrates of a mine in Inner Mongolia is mainly wrapped in pyrite and arsenopy-rite, and together with the existence of metallic antimony sulfide, cyanide leaching rate of gold in the production is relatively low,only 76. 63 %. By optimization experiment of conventional cyanide process conditions, gold recovery rate can reach a max of 80. 15 % , using alkaline leaching to pretreat the arsenic and antimony contained refractory gold concentrate, with the arsenic and antimony first removed, the cyanide leaching rate of gold increased from 76. 63 % to 92 % , achieving satisfactory technical and economical index.

  1. Photocytotoxic lanthanide complexes

    Indian Academy of Sciences (India)

    Akhtar Hussain; Akhil R Chakravarty

    2012-11-01

    Lanthanide complexes have recently received considerable attention in the field of therapeutic and diagnostic medicines. Among many applications of lanthanides, gadolinium complexes are used as magnetic resonance imaging (MRI) contrast agents in clinical radiology and luminescent lanthanides for bioanalysis, imaging and sensing. The chemistry of photoactive lanthanide complexes showing biological applications is of recent origin. Photodynamic therapy (PDT) is a non-invasive treatment modality of cancer using a photosensitizer drug and light. This review primarily focuses on different aspects of the chemistry of lanthanide complexes showing photoactivated DNA cleavage activity and cytotoxicity in cancer cells. Macrocyclic texaphyrin-lanthanide complexes are known to show photocytotoxicity with the PDT effect in near-IR light. Very recently, non-macrocyclic lanthanide complexes are reported to show photocytotoxicity in cancer cells. Attempts have been made in this perspective article to review and highlight the photocytotoxic behaviour of various lanthanide complexes for their potential photochemotherapeutic applications.

  2. Complexity Through Nonextensivity

    CERN Document Server

    Bialek, W; Tishby, N; Bialek, William; Nemenman, Ilya; Tishby, Naftali

    2001-01-01

    The problem of defining and studying complexity of a time series has interested people for years. In the context of dynamical systems, Grassberger has suggested that a slow approach of the entropy to its extensive asymptotic limit is a sign of complexity. We investigate this idea further by information theoretic and statistical mechanics techniques and show that these arguments can be made precise, and that they generalize many previous approaches to complexity, in particular unifying ideas from the physics literature with ideas from learning and coding theory; there are even connections of this statistical approach to algorithmic or Kolmogorov complexity. Moreover, a set of simple axioms similar to those used by Shannon in his development of information theory allows us to prove that the divergent part of the subextensive component of the entropy is a unique complexity measure. We classify time series by their complexities and demonstrate that beyond the `logarithmic' complexity classes widely anticipated in...

  3. Quantum State Complexity Measure

    CERN Document Server

    Campbell, Yuri

    2011-01-01

    The complexity measures role has become much clearer in recent years as they help to better understand complex systems dynamical behavior. Even though the large number of measures proposed to tackle this issue for classical systems, for quantum systems only Kolmogorov's algorithm complexity extensions have been proposed. Hence, the present approach makes use of a new and mathematically well-established complexity measure for classical systems and extends it to assess quantum states complexity as well. Then the proposed extension is applied to a mixed state constructed with a W-state together with controlled white noise, showing a convex behavior of quantum state complexity. Thus, this reinforces the differences from previous known quantum complexities.

  4. Avaliação da tolerância e nefrotoxicidade do antimonial pentavalente administrado na dose de 40mg Sb v/kg/dia, de 12/12h, por 30 dias na forma cutaneo-mucosa de leishmaniose

    Directory of Open Access Journals (Sweden)

    Raimunda N.R. Sampaio

    1997-12-01

    Full Text Available Foi avaliada a função renal de 11 pacientes com leishmaniose cutâneo-mucosa tratados com antimonial pentavalente na dose de 40mg SbV/kg/dia aplicada de 12/12 horas, em esquema contínuo, durante trinta dias. No estudo, um paciente apresentou insuficiência renal reversível e dois desenvolveram alterações enzimáticas hepáticas e eletrocardiográficas sendo o esquema terapêutico interrompido. Nos demais pacientes observou-se efeitos nefrotóxicos tais como diminuição da taxa de filtração glomerular, diminuição da capacidade de concentração urinária, avaliada por um jejum hídrico de 16 horas e aumento na fração de excreção de sódio. No exame do sedimento urinário observou-se um aumento no número de leucócitos e cilindros. Os resultados encontrados neste estudo sugerem que o tratamento com antimonial pentavalente na dose de 40mg SbV/kg/dia foi menos tolerado em virtude de seus efeitos tóxicos, não parecendo apresentar índice de cura superior ao esquema atualmente preconizado de 20mg SbV/kg/dia.The renal function of eleven patients with mucocutaneous leishmaniasis was analyzed in a prospective study realized at the School Hospital of University of Brasília. The patients were treated with doses of 40mg/kg/day of pentavalent antimony (SbV, in a continuous scheme during thirty days. In this study three patients were excluded, one patient with reversible renal failure and two patients with hepatic and cardiac malfunctions. In the other eight patients, severe nephrotoxics effects were observed, like reduction of glomerular filtration rate, reduction of the urinary concentration capacity, evaluated by a sixteen hours hydric fasting and an increase of sodium fractional excretion. An increase in the number of leucocytes and cylinders were observed at the urinary sediment exam. Finally, the results shows that the treatment with pentavalent antimony in doses of 40mg Sb/kg/day was less tolerated on account of its renal toxics

  5. Cytotoxicity and apoptotic activity of novel organobismuth(V) and organoantimony(V) complexes in different cancer cell lines.

    Science.gov (United States)

    Islam, Arshad; Rodrigues, Bernardo Lages; Marzano, Ivana Marques; Perreira-Maia, Elene C; Dittz, Dalton; Paz Lopes, Miriam Teresa; Ishfaq, Muhammad; Frézard, Frédéric; Demicheli, Cynthia

    2016-02-15

    Novel organobismuth(V) and organoantimony(V) complexes of Ph3ML2 type were synthesized, in which L = deprotonated 2-acetylbenzoic acid (2AcBH), 4-acetylbenzoic acid (4AcBH) or 5-acetylsalicylic acid (5AcSH) and M = bismuth(V) or antimony(V). Complexes [Ph3Bi(2AcB)2] (1) [Ph3Sb(4AcB)2] (2), [Ph3Bi(4AcB)2] (3) and [Ph3Sb(5AcS)2(.)CHCl3] (4) were characterized by elemental analysis, IR, and NMR. Crystal structures of 2 and 4 were determined by single crystal X-ray diffraction. In vitro cytotoxic activities against cancerous (human chronic myelogenous leukemia, K562 and murine metastatic melanoma, B16F10) and healthy non-cancerous (murine fibroblasts, L929 and murine melanocytes, Melan-A) cells showed that, compared to free ligands, both of the metal complexes are more active as anticancer agents at low concentration in cancerous cell lines, but also possessed toxic effect at comparatively higher concentration towards the non-cancerous cells. The organobismuth(V) complex Ph3Bi(2AcB)2 was found to be more active than the Ph3BiCl2 metal precursor against the tumor cell lines and exhibited the highest selectivity index. Moreover, evaluation of the pro-apoptotic activity of Ph3Bi(2AcB)2 in B16F10 cells, by quantifying the cellular DNA using flow cytometry, indicates that cell cycle arrest and cell apoptosis contribute to the drug cytotoxicity. This work supports the great potential of organobismuth(V) dicarboxylate complexes as anticancer agents.

  6. Measuring static complexity

    Directory of Open Access Journals (Sweden)

    Ben Goertzel

    1992-01-01

    Full Text Available The concept of “pattern” is introduced, formally defined, and used to analyze various measures of the complexity of finite binary sequences and other objects. The standard Kolmogoroff-Chaitin-Solomonoff complexity measure is considered, along with Bennett's ‘logical depth’, Koppel's ‘sophistication'’, and Chaitin's analysis of the complexity of geometric objects. The pattern-theoretic point of view illuminates the shortcomings of these measures and leads to specific improvements, it gives rise to two novel mathematical concepts--“orders” of complexity and “levels” of pattern, and it yields a new measure of complexity, the “structural complexity”, which measures the total amount of structure an entity possesses.

  7. Complex networks and computing

    Institute of Scientific and Technical Information of China (English)

    Shuigeng ZHOU; Zhongzhi ZHANG

    2009-01-01

    @@ Nowadays complex networks are pervasive in various areas of science and technology. Popular examples of complex networks include the Internet, social networks of collaboration, citations and co-authoring, as well as biological networks such as gene and protein interactions and others. Complex networks research spans across mathematics, computer science, engineering, biology and the social sciences. Even in computer science area, increasing problems are either found to be related to complex networks or studied from the perspective of complex networks, such as searching on Web and P2P networks, routing in sensor networks, language processing, software engineering etc. The interaction and mergence of complex networks and computing is inspiring new chances and challenges in computer science.

  8. Two giant stellar complexes

    Science.gov (United States)

    Efremov, Yu. N.; Efremov, E. Yu.

    Common star complexes are huge (0.3-1 kpc in diameter) groups of relatively young stars, associations and clusters. The complexes usually form regular chains along spiral arms of grand design galaxies, being evidently formed and supported by magneto- gravitational instability developing along an arm. Special attention is given to a few large complexes which have signatures of gravitational boundness, such as round shape and high central density. Concentrations of stars and clusters in such a complex in M51 galaxy were found in this paper; we concluded it is possible to suggest that the complex is gravitationally bound. It is also stressed that some properties of the giant complex in NGC 6946 (such as its semicircular and sharp Western edge) are still enigmatic.

  9. Simplicial complexes of graphs

    CERN Document Server

    Jonsson, Jakob

    2008-01-01

    A graph complex is a finite family of graphs closed under deletion of edges. Graph complexes show up naturally in many different areas of mathematics, including commutative algebra, geometry, and knot theory. Identifying each graph with its edge set, one may view a graph complex as a simplicial complex and hence interpret it as a geometric object. This volume examines topological properties of graph complexes, focusing on homotopy type and homology. Many of the proofs are based on Robin Forman's discrete version of Morse theory. As a byproduct, this volume also provides a loosely defined toolbox for attacking problems in topological combinatorics via discrete Morse theory. In terms of simplicity and power, arguably the most efficient tool is Forman's divide and conquer approach via decision trees; it is successfully applied to a large number of graph and digraph complexes.

  10. On Complex Random Variables

    Directory of Open Access Journals (Sweden)

    Anwer Khurshid

    2012-07-01

    Full Text Available Normal 0 false false false EN-US X-NONE X-NONE In this paper, it is shown that a complex multivariate random variable  is a complex multivariate normal random variable of dimensionality if and only if all nondegenerate complex linear combinations of  have a complex univariate normal distribution. The characteristic function of  has been derived, and simpler forms of some theorems have been given using this characterization theorem without assuming that the variance-covariance matrix of the vector  is Hermitian positive definite. Marginal distributions of  have been given. In addition, a complex multivariate t-distribution has been defined and the density derived. A characterization of the complex multivariate t-distribution is given. A few possible uses of this distribution have been suggested.

  11. How evolution guides complexity

    OpenAIRE

    LARRY S. YAEGER

    2009-01-01

    Long-standing debates about the role of natural selection in the growth of biological complexity over geological time scales are difficult to resolve from the paleobiological record. Using an evolutionary model—a computational ecosystem subjected to natural selection—we investigate evolutionary trends in an information-theoretic measure of the complexity of the neural dynamics of artificial agents inhabiting the model. Our results suggest that evolution always guides complexity change, just n...

  12. Quantum Computational Complexity

    OpenAIRE

    Watrous, John

    2008-01-01

    This article surveys quantum computational complexity, with a focus on three fundamental notions: polynomial-time quantum computations, the efficient verification of quantum proofs, and quantum interactive proof systems. Properties of quantum complexity classes based on these notions, such as BQP, QMA, and QIP, are presented. Other topics in quantum complexity, including quantum advice, space-bounded quantum computation, and bounded-depth quantum circuits, are also discussed.

  13. Complex Systems and Dependability

    CERN Document Server

    Zamojski, Wojciech; Sugier, Jaroslaw

    2012-01-01

    Typical contemporary complex system is a multifaceted amalgamation of technical, information, organization, software and human (users, administrators and management) resources. Complexity of such a system comes not only from its involved technical and organizational structure but mainly from complexity of information processes that must be implemented in the operational environment (data processing, monitoring, management, etc.). In such case traditional methods of reliability analysis focused mainly on technical level are usually insufficient in performance evaluation and more innovative meth

  14. Genetics of complex diseases.

    Science.gov (United States)

    Motulsky, Arno G

    2006-02-01

    Approaches to the study of the genetic basis of common complex diseases and their clinical applications are considered. Monogenic Mendelian inheritance in such conditions is infrequent but its elucidation may help to detect pathogenic mechanisms in the more common variety of complex diseases. Involvement by multiple genes in complex diseases usually occurs but the isolation and identification of specific genes so far has been exceptional. The role of common polymorphisms as indicators of disease risk in various studies is discussed.

  15. Engineering Complex Tissues

    OpenAIRE

    Mikos, Antonios G.; Herring, Susan W.; OCHAREON, PANNEE; Elisseeff, Jennifer; Lu, Helen H.; Kandel, Rita; Schoen, Frederick J.; Toner, Mehmet; Mooney, David; ATALA, ANTHONY; VAN DYKE, MARK E.; Kaplan, David; Vunjak-Novakovic, Gordana

    2006-01-01

    This article summarizes the views expressed at the third session of the workshop “Tissue Engineering—The Next Generation,” which was devoted to the engineering of complex tissue structures. Antonios Mikos described the engineering of complex oral and craniofacial tissues as a “guided interplay” between biomaterial scaffolds, growth factors, and local cell populations toward the restoration of the original architecture and function of complex tissues. Susan Herring, reviewing osteogenesis and ...

  16. MULTISCALE COMPLEXITY/ENTROPY

    OpenAIRE

    Y. BAR-YAM

    2004-01-01

    We discuss the role of scale dependence of entropy/complexity and its relationship to component interdependence. The complexity as a function of scale of observation is expressed in terms of subsystem entropies for a system having a description in terms of variables that have the same a priori scale. The sum of the complexity over all scales is the same for any system with the same number of underlying degrees of freedom (variables), even though the complexity at specific scales differs due t...

  17. Berger Engineering Complex

    Data.gov (United States)

    Federal Laboratory Consortium — Description/History: Engineering laboratory The Berger Lab Complex is a multi-purpose building with professional office, 100 seat auditorium, general purpose labs,...

  18. Complexity, Robustness, and Performance

    NARCIS (Netherlands)

    B. Visser (Bauke)

    2002-01-01

    textabstractThis paper analyses the relationship between organizational complexity ( the degree of detail of information necessary to correctly assign agents to positions), robustness (the relative loss of performance due to mis-allocated agents), and performance. More complex structures are not nec

  19. Complexity dimensions and learnability

    NARCIS (Netherlands)

    S-H. Nienhuys-Cheng (Shan-Hwei); M. Polman

    1992-01-01

    textabstractA stochastic model of learning from examples has been introduced by Valiant [1984]. This PAC-learning model (PAC = probably approximately correct) reflects differences in complexity of concept classes, i.e. very complex classes are not efficiently PAC-learnable. Blumer et al. [1989] foun

  20. Introductory complex analysis

    CERN Document Server

    Silverman, Richard A

    1984-01-01

    A shorter version of A. I. Markushevich's masterly three-volume Theory of Functions of a Complex Variable, this edition is appropriate for advanced undergraduate and graduate courses in complex analysis. Numerous worked-out examples and more than 300 problems, some with hints and answers, make it suitable for independent study. 1967 edition.

  1. The complexity of science

    Directory of Open Access Journals (Sweden)

    H.P.P. (Hennie Lótter

    1999-03-01

    Full Text Available In this article an alternative philosophy of science based on ideas drawn from the study of complex adaptive systems is presented. As a result of the enormous expansion in scientific disciplines, and the number of scientists and scientific institutions in the twentieth century, I believe science can be characterised as a complex system. I want to interpret the processes of science through which scientists themselves determine what is regarded as good science. This characterisation of science as a complex system can supply an answer to the question why the sciences have been so successful in solving growing numbers of problems and correcting their own mistakes. I utilise components of complexity theory to explain and interpret science as a complex system. I first explain the concept of complexity in ordinary language. The explanation of science as a complex system starts with a definition of the basic rules guiding the behaviour of science as a complex system. Next, I indicate how various sciences have resulted through the implementation of these rules in the study of a specific aspect of reality. The explanation of the growth of science through evolutionary adaptation and learning forms the core o f the article.

  2. Tuberculosis in complex emergencies.

    Science.gov (United States)

    Coninx, Rudi

    2007-08-01

    This paper describes the key factors and remaining challenges for tuberculosis (TB) control programmes in complex emergencies. A complex emergency is "a humanitarian crisis in a country, region or society where there is total or considerable breakdown of authority resulting from internal or external conflict and which requires an international response that goes beyond the mandate or capacity of any single agency and/or the ongoing United Nations country programme." Some 200 million people are believed to live in countries affected by complex emergencies; almost all of these are developing countries that also bear the main burden of TB. The effects of complex emergencies impact on TB control programmes, interfering with the goals of identifying and curing TB patients and possibly leading to the emergence of MDR-TB. There are many detailed descriptions of aid interventions during complex emergencies; yet TB control programmes are absent from most of these reports. If TB is neglected, it may quickly result in increased morbidity and mortality, as was demonstrated in Bosnia and Herzegovina and in Somalia. TB is a major disease in complex emergencies and requires an appropriate public health response. While there is no manual to cover complex emergencies, the interagency manual for TB control in refugee and displaced populations provides valuable guidance. These programmes contribute to the body of evidence needed to compile such a manual, and should ensure that the experiences of TB control in complex emergencies lead to the establishment of evidence-based programmes. PMID:17768523

  3. Complexity and Relations

    Science.gov (United States)

    Lancaster, Jeanette Elizabeth

    2013-01-01

    A central feature of complexity is that it is based on non-linear, recursive relations. However, in most current accounts of complexity such relations, while non-linear, are based on the reductive relations of a Newtonian onto-epistemological framework. This means that the systems that are emergent from the workings of such relations are a…

  4. Visual Complexity: A Review

    Science.gov (United States)

    Donderi, Don C.

    2006-01-01

    The idea of visual complexity, the history of its measurement, and its implications for behavior are reviewed, starting with structuralism and Gestalt psychology at the beginning of the 20th century and ending with visual complexity theory, perceptual learning theory, and neural circuit theory at the beginning of the 21st. Evidence is drawn from…

  5. Complexity in Picture Books

    Science.gov (United States)

    Sierschynski, Jarek; Louie, Belinda; Pughe, Bronwyn

    2015-01-01

    One of the key requirements of Common Core State Standards (CCSS) in English Language Arts is that students are able to read and access complex texts across all grade levels. The CCSS authors emphasize both the limitations and lack of accuracy in the current CCSS model of text complexity, calling for the development of new frameworks. In response…

  6. Freestanding Complex Optical Scanners.

    Science.gov (United States)

    Frisbie, David A.

    A complex freestanding optical mark recognition (OMR) scanner is one which is not on-line to an external processor; it has intelligence stemming from an internal processor located within the unit or system. The advantages and disadvantages of a complex OMR can best be assessed after identifying the scanning needs and constraints of the potential…

  7. Conducting metal dithiolate complexes

    DEFF Research Database (Denmark)

    Underhill, A. E.; Ahmad, M. M.; Turner, D. J.;

    1985-01-01

    Further work on the chemical composition of the one-dimensional metallic metal dithiolene complex Li-Pt(mnt) is reported. The electrical conduction and thermopower properties of the nickel and palladium complexes are reported and compared with those of the platinum compound...

  8. Leading healthcare in complexity.

    Science.gov (United States)

    Cohn, Jeffrey

    2014-12-01

    Healthcare institutions and providers are in complexity. Networks of interconnections from relationships and technology create conditions in which interdependencies and non-linear dynamics lead to surprising, unpredictable outcomes. Previous effective approaches to leadership, focusing on top-down bureaucratic methods, are no longer effective. Leading in complexity requires leaders to accept the complexity, create an adaptive space in which innovation and creativity can flourish and then integrate the successful practices that emerge into the formal organizational structure. Several methods for doing adaptive space work will be discussed. Readers will be able to contrast traditional leadership approaches with leading in complexity. They will learn new behaviours that are required of complexity leaders, along with challenges they will face, often from other leaders within the organization.

  9. [Complexity: an introduction].

    Science.gov (United States)

    Gómez, Carlos Alberto Palacio; Jaramillo, Francisco Luis Ochoa

    2011-01-01

    Complexity appears in the twentieth century as a way to understand many phenomena that are perceived as chaotic and complex from classical thought, which still persist in our way of explaining the world. Its purpose is to study the complex and adaptive systems that are sensitive to initial conditions. Some of the characteristics of complex thought are systemic perspective, autopoiesis, self-organization, emergent properties, unpredictability of the systems, analogic thought, and the complementarity of the phenomena, among others. Living systems respond to a complex logic, and in that sense, our vision of human populations and patients, and how we try to solve problems and human diseases, should be open to the possibilities that arise from this form of understand the world. PMID:21503430

  10. Reset Complexity of Ideal Languages

    OpenAIRE

    Maslennikova, Marina

    2014-01-01

    We present a new characteristic of a regular ideal language called reset complexity. We find some bounds on the reset complexity in terms of the state complexity of a given language. We also compare the reset complexity and the state complexity for languages related to slowly synchronizing automata and study uniqueness question for automata yielding the minimum of reset complexity.

  11. Use of tetracycline as complexing agent in radiochemical separations

    International Nuclear Information System (INIS)

    A review of the work carried out in the 'Instituto de Pesquisas Energeticas e Nucleares' on the use of tetracycline for analytical purposes in solvent extraction procedures is presented. Individual extraction curves for the lanthanides, zinc, scandium, thorium, neptunium and protactinium were obtained. Separations of those elements one from another, and of uranium from silenium, bromine, antimony, barium, tantalum and tungsten were carried out. (A.R.H.)

  12. Management of complex fisheries

    DEFF Research Database (Denmark)

    Frost, Hans Staby; Andersen, Peder; Hoff, Ayoe

    2013-01-01

    The purpose of this paper is to demonstrate how fisheries economics management issues or problems can be analyzed by using a complex model based on conventional bioeconomic theory. Complex simulation models contain a number of details that make them suitable for practical management advice......, including taking into account the response of the fishermen to implemented management measures. To demonstrate the use of complex management models this paper assesses a number of second best management schemes against a first rank optimum (FRO), an ideal individual transferable quotas (ITQ) system...

  13. Complexity and forensic pathology.

    Science.gov (United States)

    Jones, Richard Martin

    2015-12-01

    It has become increasingly apparent that nonlinearity and complexity are the norm in human physiological systems, the relevance of which is informing an enhanced understanding of basic pathological processes such as inflammation, the host response to severe trauma, and critical illness. This article will explore how an understanding of nonlinear systems and complexity might inform the study of the pathophysiology of deaths of medicolegal interest, and how 'complexity thinking' might usefully be incorporated into modern forensic medicine and forensic pathology research, education and practice. PMID:26372537

  14. Research Advances in Uptake, Metabolism and Toxicity of Antimony in Plants%植物对锑的吸收和代谢及其毒性的研究进展

    Institute of Scientific and Technical Information of China (English)

    冯人伟; 韦朝阳; 涂书新

    2012-01-01

    锑(Sb)是一种有毒致癌元素,一些自然和人为因素己造成我国部分地区土壤、水体及农产品受到严重的锑污染.环境中高含量的锑不仅影响农作物生长、降低其产量,如果通过食物链被人体大量吸收,还会引起严重的健康问题.研究锑在植物体内的富集特征,对于保护环境与人体健康具有重要的现实意义.该文对当前锑在环境中的含量、污染状况、植物对锑的吸收、代谢以及锑对植物的毒害作用等方面的研究现状进行了综述.同时建议今后应加强以下3方面的研究:(1)锑在生物圈迁移与转化特征;(2)植物对锑的吸收、转运和代谢机制及锑的毒害作用机理;(3)锑污染上壤及水体的植物修复技术.%Antimony (Sb) is a toxic carcinogenic element. In some areas of China, soil, water, and agricultural products have been severely polluted by Sb because of particular natural and artificial factors. High levels of Sb in the environment can threaten the health of humans via the food chain. To protect the environment and human health, we must investigate the behavioural characteristics of Sb in plants and the biosphere. Here, we summarize recent progress in research on the mechanisms of absorption, metabolism and toxicity of Sb in plants. Attention must be paid to (1) migration and transformation behaviours in the biosphere; (2) mechanisms of uptake, transport, metabolism and toxicity in plants, especially in crops; and (3) technologies for phytoremediation of contaminated soil and water.

  15. Research Progress on the Modification and Application of Antimony-Doped Tin Dioxide Electrodes%钛基锡锑氧化物电极掺杂改性及应用研究进展

    Institute of Scientific and Technical Information of China (English)

    梁吉艳; 耿聰; 李丹; 袁飞宇; 崔丽; 王新

    2016-01-01

    电催化氧化水处理技术是近年来发展起来的一种有效处理难降解有机废水的方法,钛基锡锑氧化物涂层阳极(Ti/SnO2-Sb)因其对有机污染物具有较高的电化学氧化活性而受到关注.综述了稀土金属、非稀土金属、碳纳米管(CNTs)等物质掺杂改性Ti/SnO2-Sb电极的研究进展.简述了掺杂剂影响Ti/SnO2-Sb电极电催化活性、电流效率和电极寿命的作用机理;介绍了Ti/SnO2-Sb及其改性电极降解有机污染物的应用研究情况;展望了今后Ti/SnO2-Sb电极涂层掺杂改性及应用研究值得关注的方向.%Electrocatalytic oxidation technology is an effective method for recalcitrant organic wastewater treatment developed in recent years.Antimony-doped tin oxide coating on Ti substrate as anodes (Ti/SnO2-Sb) attract more attention because of its higher electrochemical oxidation activity for organic contaminants.In this review,the progress of modified Ti/SnO2-Sb by doping with rare earth metals,non-rare earth metal and carbon nanotubes (CNTs) are summarized.The effect mechanism of the dopants on Ti/SnO2-Sb electrode electrocatalytic activity,current efficiency and electrode life is outlined,the research situations of Ti/SnO2-Sb and the modified Ti/SnO2-Sb electrode applied for removing organic pollutants is introduced,and the noteworthy direction of doping and application of Ti/SnO2-Sb electrode is prospected.

  16. 断续流动原子荧光法测定铅锡合金中的痕量锑%Determination of Trace Amount of Antimony in Lead-tin Alloy by Intermittent Flow Atomic Fluorescence Spectrometry

    Institute of Scientific and Technical Information of China (English)

    马毅红; 尹艺青; 陈玉珍

    2012-01-01

    目的:建立氢化物发生双道原子荧光法测定铅锡合金中锑含量的方法,为测定铅锡合金中锑提供依据。方法:选择了最佳的仪器条件,进行样品处理方法、KBH4浓度、检出限、回收率等研究。结果:本方法的标准曲线方程y=157.56x-2.3962,相关系数γ=0.9999,线性范围为0~40μg/L,精密度为1.3%,检出限为0.0304μg/L,回收率达115%。结论:本方法操作简单、快速、灵敏度高、干扰少,可获得满意的结果。%Purpose: A analytical method is recommended for determination of Trace Amount of Antimony in Lead-Tin Alloy by hydride generation double channel atomic fluorescence spectrometry,which provides basis for its measurement.Methods: Optimum condition for the instrument determination is applied to conduct researches relating to the method of sampling,concentration of KBH4,detection limits and recovery rate.Results: The standard curve of the linear equation was y=157.56x-2.3962 with correlation coefficient γ = 0.9999 and linear range of 0~40 μg/L.The precision and the detection limits were 1.3 % and 0.0304 μg/L respectively while the returns-ratio achieves 115 %.Conclusion: The method is easy,fast,highly sensitive and with no much interference during the operation,which can lead to satisfactory results.

  17. On scattered subword complexity

    CERN Document Server

    Kása, Zoltán

    2011-01-01

    Special scattered subwords, in which the gaps are of length from a given set, are defined. The scattered subword complexity, which is the number of such scattered subwords, is computed for rainbow words.

  18. Complex tunneling dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Yang, C.-D. [Department of Aeronautics and Astronautics, National Cheng Kung University, Tainan 701, Taiwan (China)]. E-mail: cdyang@mail.ncku.edu.tw

    2007-04-15

    Tunneling dynamics and tunneling trajectories are modeled exactly by complex-extended Hamilton-Jacobi formulation in this paper. It is found that the wave-like properties of tunneling particles, such as reflection, refraction, and transmission resonance, can be identified and explained in terms of particle's motion in complex space with the tunneling time defined as the usual sense of classical time. Following the complex trajectories determined by the complex Hamilton equations of motion, we can connect classical trajectories smoothly with tunneling trajectories using position and velocity continuity at the interface of the media, locate the particle's position at any instant, and find the time spent by a particle within the potential. A microscopic tunneling model is also developed to explain the probabilistic nature why a particle with the same incident conditions sometimes transmits the potential and sometimes is reflected from the potential.

  19. Complex coacervate core micelles.

    Science.gov (United States)

    Voets, Ilja K; de Keizer, Arie; Cohen Stuart, Martien A

    2009-01-01

    In this review we present an overview of the literature on the co-assembly of neutral-ionic block, graft, and random copolymers with oppositely charged species in aqueous solution. Oppositely charged species include synthetic (co)polymers of various architectures, biopolymers - such as proteins, enzymes and DNA - multivalent ions, metallic nanoparticles, low molecular weight surfactants, polyelectrolyte block copolymer micelles, metallo-supramolecular polymers, equilibrium polymers, etcetera. The resultant structures are termed complex coacervate core/polyion complex/block ionomer complex/interpolyelectrolyte complex micelles (or vesicles); i.e., in short C3Ms (or C3Vs) and PIC, BIC or IPEC micelles (and vesicles). Formation, structure, dynamics, properties, and function will be discussed. We focus on experimental work; theory and modelling will not be discussed. Recent developments in applications and micelles with heterogeneous coronas are emphasized.

  20. Complex Flow Workshop Report

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2012-05-01

    This report documents findings from a workshop on the impacts of complex wind flows in and out of wind turbine environments, the research needs, and the challenges of meteorological and engineering modeling at regional, wind plant, and wind turbine scales.