WorldWideScience

Sample records for anodic alumina mask

  1. Aluminum microstructures on anodic alumina for aluminum wiring boards.

    Science.gov (United States)

    Jha, Himendra; Kikuchi, Tatsuya; Sakairi, Masatoshi; Takahashi, Hideaki

    2010-03-01

    The paper demonstrates simple methods for the fabrication of aluminum microstructures on the anodic oxide film of aluminum. The aluminum sheets were first engraved (patterned) either by laser beam or by embossing to form deep grooves on the surface. One side of the sheet was then anodized, blocking the other side by using polymer mask to form the anodic alumina. Because of the lower thickness at the bottom part of the grooves, the part was completely anodized before the complete oxidation of the other parts. Such selectively complete anodizing resulted in the patterns of metallic aluminum on anodic alumina. Using the technique, we fabricated microstructures such as line patterns and a simple wiring circuit-board-like structure on the anodic alumina. The aluminum microstructures fabricated by the techniques were embedded in anodic alumina/aluminum sheet, and this technique is promising for applications in electronic packaging and devices.

  2. Ultraviolet photoluminescence of porous anodic alumina films

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    Photoluminescence (PL) properties of porous anodic alumina (PAA) films prepared by using electrochemical anodization technique in a mixed solution of oxalic and sulfuric acid have been investigated. The PAA films have an intensive ultraviolet PL emission around 350 nm, of which a possible PL mechanism has been proposed. It was found that the incorporated oxalic ions, which could transform into PL centers and exist in the PAA films, are responsible for this ultraviolet PL emission.

  3. Masking of aluminum surface against anodizing

    Science.gov (United States)

    Crawford, G. B.; Thompson, R. E.

    1969-01-01

    Masking material and a thickening agent preserve limited unanodized areas when aluminum surfaces are anodized with chromic acid. For protection of large areas it combines well with a certain self-adhesive plastic tape.

  4. Nanotube Arrays in Porous Anodic Alumina Membranes

    Institute of Scientific and Technical Information of China (English)

    Liang LI; Naoto KOSHIZAKI; Guanghai LI

    2008-01-01

    This review summarizes the various techniques developed for fabricating nanotube arrays in porous anodic alumina membranes (AAMs). After a brief introduction to the fabrication process of AAMs, taking carbons, metals, semiconductors, organics, biomoleculars, and heterojunctions as typical examples, attention will be focused on the recently established methods to fabricate nanotubes in AAM, including electrochemical deposition, surface sol-gel, modified chemical vapor deposition, atomic layer deposition, and layer-by-layer growth. Every method is demonstrated by one or two reported results. Finally, this review is concluded with some perspectives on the research directions and focuses on the AAM-based nanotubes fields.

  5. Modelling the initial stage of porous alumina growth during anodization

    Science.gov (United States)

    Aryslanova, E. M.; Alfimov, A. V.; Chivilikhin, S. A.

    2013-05-01

    Artificially on the surface of aluminum there may be build a thick layer of Al2O3, which has a porous structure. In this paper we present a model of growth of porous alumina in the initial stage of anodizing, identifying dependencies anodizing parameters on the rate of growth of the film and the distance between the pores and as a result of the created model equations were found for changes in the disturbance of alumina for the initial stage of anodizing aluminum oxide porous border aluminum-alumina and alumina-electrolyte, with the influence of surface diffusion of aluminum oxide.

  6. Electrochemical modification process of anodic alumina membrane

    Institute of Scientific and Technical Information of China (English)

    YU Mei; LIU Jian-hua; LI Song-mei

    2006-01-01

    The modification procedure of anodic alumina membrane(AAM) was studied. The AAM structure after modification was characterized by nickel nanowires prepared in AAM. Scanning electron microscopy was used to characterize the topography and structure properties of the AAM and nickel nanowires. The transformation of the current during the voltage reduction was studied. The mechanism of current and structure change during modification was discussed. The results show that a root structure produces after the AAM modification. The length of the root structure depends on the velocity of the voltage reduction. Slow voltage reduction leads to a large length of the root structure,otherwise,a short length of the root structure. At the end of the modification,the barrier layer is thin enough to be passed by electrons. Hence,the direct electrodeposition of one-dimensional nanowires can be carried out on the AAM with barrier layer and aluminum matrix successfully without any other treatments.

  7. Modulation of Transmission Spectra of Anodized Alumina Membrane Distributed Bragg Reflector by Controlling Anodization Temperature

    Directory of Open Access Journals (Sweden)

    Zheng WenJun

    2009-01-01

    Full Text Available Abstract We have successfully prepared anodized alumina membrane distributed Bragg reflector (DBR using electrochemical anodization method. The transmission peak of this distributed Bragg reflector could be easily and effectively modulated to cover almost any wavelength range of the whole visible spectrum by adjusting anodization temperature.

  8. Ultra-High Density Single Nanometer-Scale Anodic Alumina Nanofibers Fabricated by Pyrophosphoric Acid Anodizing

    Science.gov (United States)

    Kikuchi, Tatsuya; Nishinaga, Osamu; Nakajima, Daiki; Kawashima, Jun; Natsui, Shungo; Sakaguchi, Norihito; Suzuki, Ryosuke O.

    2014-12-01

    Anodic oxide fabricated by anodizing has been widely used for nanostructural engineering, but the nanomorphology is limited to only two oxides: anodic barrier and porous oxides. Therefore, the discovery of an additional anodic oxide with a unique nanofeature would expand the applicability of anodizing. Here we demonstrate the fabrication of a third-generation anodic oxide, specifically, anodic alumina nanofibers, by anodizing in a new electrolyte, pyrophosphoric acid. Ultra-high density single nanometer-scale anodic alumina nanofibers (1010 nanofibers/cm2) consisting of an amorphous, pure aluminum oxide were successfully fabricated via pyrophosphoric acid anodizing. The nanomorphologies of the anodic nanofibers can be controlled by the electrochemical conditions. Anodic tungsten oxide nanofibers can also be fabricated by pyrophosphoric acid anodizing. The aluminum surface covered by the anodic alumina nanofibers exhibited ultra-fast superhydrophilic behavior, with a contact angle of less than 1°, within 1 second. Such ultra-narrow nanofibers can be used for various nanoapplications including catalysts, wettability control, and electronic devices.

  9. Fabrication of alumina films with laminated structures by ac anodization

    Directory of Open Access Journals (Sweden)

    Hiroyo Segawa

    2014-01-01

    Full Text Available Anodization techniques by alternating current (ac are introduced in this review. By using ac anodization, laminated alumina films are fabricated. Different types of alumina films consisting of 50–200 nm layers were obtained by varying both the ac power supply and the electrolyte. The total film thickness increased with an increase in the total charge transferred. The thickness of the individual layers increased with the ac voltage; however, the anodization time had little effect on the film thickness. The laminated alumina films resembled the nacre structure of shells, and the different morphologies exhibited by bivalves and spiral shells could be replicated by controlling the rate of increase of the applied potentials.

  10. Energy transfer in porous anodic alumina/rhodamine 110 nanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Elhouichet, H., E-mail: habib.elhouichet@fst.rnu.tn [Laboratoire de Physico-Chimie des Materiaux Mineraux et leurs Applications, Centre National de Recherches en Sciences des Materiaux, B.P. 95, Hammam-Lif 2050 (Tunisia); Departement de Physique, Faculte des Sciences de Tunis, University of Tunis Elmanar 2092 Tunis (Tunisia); Harima, N.; Koyama, H. [Hyogo University of Teacher Education, Kato, Hyogo 673-1494 (Japan); Gaponenko, N.V. [Belarusian State University of Informatics and Radioelectronics, P. Browki St. 6, 220013 Minsk (Belarus)

    2012-09-15

    We have used porous anodic alumina (PAA) films as templates for embedding rhodamine 110 (Rh110) molecules and examined their photoluminescence (PL) properties in detail. The analysis of the polarization memory (PM) of PL strongly suggests that there is a significant energy transfer from PAA to Rh110 molecules. The effect of annealing the PAA layer on the PL properties of the nanocomposite has been studied. The results show that the energy transfer becomes more efficient in annealed PAA. - Highlights: Black-Right-Pointing-Pointer Porous anodic alumina-rhodamine 110 nanocomposites are elaborated. Black-Right-Pointing-Pointer Efficient energy transfer from the host to Rh110 molecules is evidenced from measurements of photoluminescence and degree of polarization memory spectra. Black-Right-Pointing-Pointer Thermal annealing of porous anodic alumina can improve the process of excitation transfer.

  11. Cylindrical Three-Dimensional Porous Anodic Alumina Networks

    Directory of Open Access Journals (Sweden)

    Pedro M. Resende

    2016-11-01

    Full Text Available The synthesis of a conformal three-dimensional nanostructure based on porous anodic alumina with transversal nanopores on wires is herein presented. The resulting three-dimensional network exhibits the same nanostructure as that obtained on planar geometries, but with a macroscopic cylindrical geometry. The morphological analysis of the nanostructure revealed the effects of the initial defects on the aluminum surface and the mechanical strains on the integrity of the three-dimensional network. The results evidence the feasibility of obtaining 3D porous anodic alumina on non-planar aluminum substrates.

  12. Superhydrophobicity of Bionic Alumina Surfaces Fabricated by Hard Anodizing

    Institute of Scientific and Technical Information of China (English)

    Jing Li; Feng Du; Xianli Liu; Zhonghao Jiang; Luquan Ren

    2011-01-01

    Bionic alumina samples were fabricated on convex dome type aluminum alloy substrate using hard anodizing technique.The convex domes on the bionic sample were fabricated by compression molding under a compressive stress of 92.5 MPa.The water contact angles of the as-anodized bionic samples were measured using a contact angle meter (JC2000A) with the 3 μL water drop at room temperature.The measurement of the wetting property showed that the water contact angle of the unmodified as-anodized bionic alumina samples increases from 90° to 137° with the anodizing time.The increase in water contract angle with anodizing time arises from the gradual formation of hierarchical structure or composite structure.The structure is composed of the micro-scaled alumina columns and pores.The height of columns and the depth of pores depend on the anodizing time.The water contact angle increases significantly from 96° to 152° when the samples were modified with self-assembled monolayer of octadecanethiol (ODT),showing a change in the wettability from hydrophobicity to super-hydrophobicity.This improvement in the wetting property is attributed to the decrease in the surface energy caused by the chemical modification.

  13. Characterization of nanopores ordering in anodic alumina

    DEFF Research Database (Denmark)

    Mátéfi-Tempfli, Stefan; Mátéfi-Tempfli, M.; Piraux, L.

    2008-01-01

    A simple characterization method of the ordering of the nanopores is described for nanoporous anodized aluminium oxides. The method starts with image analysis on scanning electron microscopy representations for the purpose to find repetitive shapes and their centres, i.e. nanopores. Then triangles...

  14. Formation of complex anodic films on porous alumina matrices

    Indian Academy of Sciences (India)

    Alexander Zahariev; Assen Girginov

    2003-04-01

    The kinetics of growth of complex anodic alumina films was investigated. These films were formed by filling porous oxide films (matrices) having deep pores. The porous films (matrices) were obtained voltastatically in (COOH)2 aqueous solution under various voltages. The filling was done by re-anodization in an electrolyte solution not dissolving the film. Data about the kinetics of re-anodization depending on the porosity of the matrices were obtained. On the other hand, the slopes of the kinetic curves during reanodization were calculated by two equations expressing the dependence of these slopes on the ionic current density. A discrepancy was ascertained between the values of the calculated slopes and those experimentally found. For this discrepancy a possible explanation is proposed, related to the temperature increase in the film, because of that the real current density significantly increases during re-anodization.

  15. Optical properties of porous anodic alumina embedded Cu nanocomposite films

    Science.gov (United States)

    Liu, Huiyuan; Sun, Huiyuan; Liu, Lihu; Hou, Xue; Jia, Xiaoxuan

    2015-06-01

    Porous anodic alumina embedded Cu with iridescent colors were fabricated in copper sulfate electrolyte. The films display highly saturated colors after being synthesized by an ac electrodeposition method. Tunable color in the films is obtained by adjusting anodization time, and can be adjusted across the entire visible range. Theoretical results of the changes in the structural color according to the Bragg-Snell formula are consistent with the experimental results. The films could be used in many areas including decoration, display and multifunctional anti-counterfeiting applications.

  16. Advanced morphological analysis of patterns of thin anodic porous alumina

    Energy Technology Data Exchange (ETDEWEB)

    Toccafondi, C. [Istituto Italiano di Tecnologia, Department of Nanophysics, Via Morego 30, Genova I 16163 (Italy); Istituto Italiano di Tecnologia, Department of Nanostructures, Via Morego 30, Genova I 16163 (Italy); Stępniowski, W.J. [Department of Advanced Materials and Technologies, Faculty of Advanced Technologies and Chemistry, Military University of Technology, 2 Kaliskiego Str., 00-908 Warszawa (Poland); Leoncini, M. [Istituto Italiano di Tecnologia, Department of Nanostructures, Via Morego 30, Genova I 16163 (Italy); Salerno, M., E-mail: marco.salerno@iit.it [Istituto Italiano di Tecnologia, Department of Nanophysics, Via Morego 30, Genova I 16163 (Italy)

    2014-08-15

    Different conditions of fabrication of thin anodic porous alumina on glass substrates have been explored, obtaining two sets of samples with varying pore density and porosity, respectively. The patterns of pores have been imaged by high resolution scanning electron microscopy and analyzed by innovative methods. The regularity ratio has been extracted from radial profiles of the fast Fourier transforms of the images. Additionally, the Minkowski measures have been calculated. It was first observed that the regularity ratio averaged across all directions is properly corrected by the coefficient previously determined in the literature. Furthermore, the angularly averaged regularity ratio for the thin porous alumina made during short single-step anodizations is lower than that of hexagonal patterns of pores as for thick porous alumina from aluminum electropolishing and two-step anodization. Therefore, the regularity ratio represents a reliable measure of pattern order. At the same time, the lower angular spread of the regularity ratio shows that disordered porous alumina is more isotropic. Within each set, when changing either pore density or porosity, both regularity and isotropy remain rather constant, showing consistent fabrication quality of the experimental patterns. Minor deviations are tentatively discussed with the aid of the Minkowski measures, and the slight decrease in both regularity and isotropy for the final data-points of the porosity set is ascribed to excess pore opening and consequent pore merging. - Highlights: • Thin porous alumina is partly self-ordered and pattern analysis is required. • Regularity ratio is often misused: we fix the averaging and consider its spread. • We also apply the mathematical tool of Minkowski measures, new in this field. • Regularity ratio shows pattern isotropy and Minkowski helps in assessment. • General agreement with perfect artificial patterns confirms the good manufacturing.

  17. Nanocarbon-Coated Porous Anodic Alumina for Bionic Devices

    Directory of Open Access Journals (Sweden)

    Morteza Aramesh

    2015-08-01

    Full Text Available A highly-stable and biocompatible nanoporous electrode is demonstrated herein. The electrode is based on a porous anodic alumina which is conformally coated with an ultra-thin layer of diamond-like carbon. The nanocarbon coating plays an essential role for the chemical stability and biocompatibility of the electrodes; thus, the coated electrodes are ideally suited for biomedical applications. The corrosion resistance of the proposed electrodes was tested under extreme chemical conditions, such as in boiling acidic/alkali environments. The nanostructured morphology and the surface chemistry of the electrodes were maintained after wet/dry chemical corrosion tests. The non-cytotoxicity of the electrodes was tested by standard toxicity tests using mouse fibroblasts and cortical neurons. Furthermore, the cell–electrode interaction of cortical neurons with nanocarbon coated nanoporous anodic alumina was studied in vitro. Cortical neurons were found to attach and spread to the nanocarbon coated electrodes without using additional biomolecules, whilst no cell attachment was observed on the surface of the bare anodic alumina. Neurite growth appeared to be sensitive to nanotopographical features of the electrodes. The proposed electrodes show a great promise for practical applications such as retinal prostheses and bionic implants in general.

  18. Preparation of Porous Alumina Film on Aluminum Substrate by Anodization in Oxalic Acid

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Self-ordering of the cell arrangement of the anodic porous alumina was prepared in oxalic acid solution at a constant potential of 40V and at a temperature of 20°C. The honeycomb structure made by one step anodization method and two step anodization method is different.Pores in the alumina film prepared by two step anodization method were more ordered than those by one step anodization method.

  19. Growth behavior of anodic porous alumina formed in malic acid solution

    Science.gov (United States)

    Kikuchi, Tatsuya; Yamamoto, Tsuyoshi; Suzuki, Ryosuke O.

    2013-11-01

    The growth behavior of anodic porous alumina formed on aluminum by anodizing in malic acid solutions was investigated. High-purity aluminum plates were electropolished in CH3COOH/HClO4 solutions and then anodized in 0.5 M malic acid solutions at 293 K and constant cell voltages of 200-350 V. The anodic porous alumina grew on the aluminum substrate at voltages of 200-250 V, and a black, burned oxide film was formed at higher voltages. The nanopores of the anodic oxide were only formed at grain boundaries of the aluminum substrate during the initial stage of anodizing, and then the growth region extended to the entire aluminum surface as the anodizing time increased. The anodic porous alumina with several defects was formed by anodizing in malic acid solution at 250 V, and oxide cells were approximately 300-800 nm in diameter.

  20. Crystallography-Induced Correlations in Pore Ordering of Anodic Alumina Films

    NARCIS (Netherlands)

    Roslyakov, Ilya V.; Koshkodaev, Dmitry S.; Eliseev, Andrei A.; Hermida-Merino, Daniel; Petukhov, Andrei V.; Napolskii, Kirill S.

    2016-01-01

    A crystallographic approach to tailoring the morphology and ordering degree of the porous structure of alumina films obtained by anodization of single-crystalline aluminum is discussed. The examination of porous structure of anodic alumina films formed on low-index and vicinal planes of Al single cr

  1. High field matching effects in superconducting Nb porous arrays catalyzed from anodic alumina templates

    DEFF Research Database (Denmark)

    Vinckx, W.; Vanacken, J.; Moshchalkov, V.V.;

    2007-01-01

    Vortex pinning in a superconducting Nb thin film deposited on an anodically grown alumina template is investigated. Anodic oxidation of aluminium layers permits under specific conditions the formation of highly ordered porous alumina, a membrane-like structure consisting of triangular arrays...... of parallel pores. Its pore diameter and interpore distance are set by careful tuning of the anodization parameters. A superconducting Nb thin film is deposited directly onto the alumina film. The porous alumina acts as a template and it allows Nb to form a periodic pinning array during its growth. Pinning...

  2. Terbium luminescence in alumina xerogel fabricated in porous anodic alumina matrix under various excitation conditions

    Energy Technology Data Exchange (ETDEWEB)

    Gaponenko, N. V., E-mail: nik@nano.bsuir.edu.by [Belarusian State University of Informatics and Radioelectronics (Belarus); Kortov, V. S. [Yeltsin Ural Federal University (Russian Federation); Orekhovskaya, T. I.; Nikolaenko, I. A. [Belarusian State University of Informatics and Radioelectronics (Belarus); Pustovarov, V. A.; Zvonarev, S. V.; Slesarev, A. I. [Yeltsin Ural Federal University (Russian Federation); Prislopski, S. Ya. [National Academy of Sciences of Belarus, Stepanov Institute of Physics (Belarus)

    2011-07-15

    Terbium-doped alumina xerogel layers are synthesized by the sol-gel method in pores of a porous anodic alumina film 1 {mu}m thick with a pore diameter of 150-180 nm; the film is grown on a silicon substrate. The fabricated structures exhibit terbium photoluminescence with bands typical of trivalent terbium terms. Terbium X-ray luminescence with the most intense band at 542 nm is observed for the first time for such a structure. Morphological analysis of the structure by scanning electron microscopy shows the presence of xerogel clusters in pore channels, while the main pore volume remains unfilled and pore mouths remain open. The data obtained confirm the promising applications of fabricated structures for developing matrix converters of X-rays and other ionizing radiations into visible light. The possibilities of increasing luminescence intensity in the matrix converter are discussed.

  3. Porous and mesh alumina formed by anodization of high purity aluminum films at low anodizing voltage

    Energy Technology Data Exchange (ETDEWEB)

    Abd-Elnaiem, Alaa M., E-mail: alaa.abd-elnaiem@science.au.edu.eg [KACST-Intel Consortium Center of Excellence in Nano-manufacturing Applications (CENA), Riyadh (Saudi Arabia); Physics Department, Faculty of Science, Assiut University, Assiut 71516 (Egypt); Mebed, A.M. [Physics Department, Faculty of Science, Assiut University, Assiut 71516 (Egypt); Department of Physics, Faculty of Science, Al-Jouf University, Sakaka 2014 (Saudi Arabia); El-Said, Waleed Ahmed [Department of Chemistry, Faculty of Science, Assiut University, Assiut 71516 (Egypt); Abdel-Rahim, M.A. [Physics Department, Faculty of Science, Assiut University, Assiut 71516 (Egypt)

    2014-11-03

    Electrochemical oxidation of high-purity aluminum (Al) films under low anodizing voltages (1–10) V has been conducted to obtain anodic aluminum oxide (AAO) with ultra-small pore size and inter-pore distance. Different structures of AAO have been obtained e.g. nanoporous and mesh structures. Highly regular pore arrays with small pore size and inter-pore distance have been formed in oxalic or sulfuric acids at different temperatures (22–50 °C). It is found that the pore diameter, inter-pore distance and the barrier layer thickness are independent of the anodizing parameters, which is very different from the rules of general AAO fabrication. The brand formation mechanism has been revealed by the scanning electron microscope study. Regular nanopores are formed under 10 V at the beginning of the anodization and then serve as a template layer dominating the formation of ultra-small nanopores. Anodization that is performed at voltages less than 5 V leads to mesh structured alumina. In addition, we have introduced a simple one-pot synthesis method to develop thin walls of oxide containing lithium (Li) ions that could be used for battery application based on anodization of Al films in a supersaturated mixture of lithium phosphate and phosphoric acid as matrix for Li-composite electrolyte. - Highlights: • We develop anodic aluminum oxide (AAO) with small pore size and inter-pore distance. • Applying low anodizing voltages onto aluminum film leads to form mesh structures. • The value of anodizing voltage (1–10 V) has no effect on pore size or inter-pore distance. • Applying anodizing voltage less than 5 V leads to mesh structured AAO. • AAO can be used as a matrix for Li-composite electrolytes.

  4. Transport properties of anodic porous alumina for ReRAM

    Energy Technology Data Exchange (ETDEWEB)

    Kato, S; Nigo, S; Lee, J W; Mihalik, M; Kitazawa, H; Kido, G [National Institute for Materials Science, 1-2-1 Sengen, Tsukuba, Ibaraki, 305-0047 (Japan)], E-mail: KATO.Seiichi@nims.go.jp

    2008-03-15

    A voltage-induced bistable switching effect has been studied for M/AlO{sub x}/Al devices made of the anodic porous alumina with a top electrode of aluminium (or silver) to develop a next generation memory (AlO{sub x}-ReRAM). The resistance state of memory is switched between OFF-state (high resistance) and ON-state (low resistance), where the resistance ratio is higher than 10{sup 4}. In the thermally stimulated current (TSC) measurement, a narrow band was observed around 290 K, indicating the conduction mechanism comes from a kind of impurity band in the energy gap. An anomaly was also observed around 290 K in the temperature dependence of resistance at the ON-state.

  5. Nanoporous Anodic Alumina: A Versatile Platform for Optical Biosensors

    Directory of Open Access Journals (Sweden)

    Abel Santos

    2014-05-01

    Full Text Available Nanoporous anodic alumina (NAA has become one of the most promising nanomaterials in optical biosensing as a result of its unique physical and chemical properties. Many studies have demonstrated the outstanding capabilities of NAA for developing optical biosensors in combination with different optical techniques. These results reveal that NAA is a promising alternative to other widely explored nanoporous platforms, such as porous silicon. This review is aimed at reporting on the recent advances and current stage of development of NAA-based optical biosensing devices. The different optical detection techniques, principles and concepts are described in detail along with relevant examples of optical biosensing devices using NAA sensing platforms. Furthermore, we summarise the performance of these devices and provide a future perspective on this promising research field.

  6. Ordered Nanomaterials Thin Films via Supported Anodized Alumina Templates

    Directory of Open Access Journals (Sweden)

    Mohammed eES-SOUNI

    2014-10-01

    Full Text Available Supported anodized alumina template films with highly ordered porosity are best suited for fabricating large area ordered nanostructures with tunable dimensions and aspect ratios. In this paper we first discuss important issues for the generation of such templates, including required properties of the Al/Ti/Au/Ti thin film heterostructure on a substrate for high quality templates. We then show examples of anisotropic nanostructure films consisting of noble metals using these templates, discuss briefly their optical properties and their applications to molecular detection using surface enhanced Raman spectroscopy. Finally we briefly address the possibility to make nanocomposite films, exemplary shown on a plasmonic-thermochromic nanocomposite of VO2-capped Au-nanorods.

  7. AFM, SEM and TEM Studies on Porous Anodic Alumina

    Science.gov (United States)

    Zhu, Yuan Yuan; Ding, Gu Qiao; Ding, Jian Ning; Yuan, Ning Yi

    2010-04-01

    Porous anodic alumina (PAA) has been intensively studied in past decade due to its applications for fabricating nanostructured materials. Since PAA’s pore diameter, thickness and shape vary too much, a systematical study on the methods of morphology characterization is meaningful and essential for its proper development and utilization. In this paper, we present detailed AFM, SEM and TEM studies on PAA and its evolvements with abundant microstructures, and discuss the advantages and disadvantages of each method. The sample preparation, testing skills and morphology analysis are discussed, especially on the differentiation during characterizing complex cross-sections and ultrasmall nanopores. The versatility of PAAs is also demonstrated by the diversity of PAAs’ microstructure.

  8. AFM, SEM and TEM Studies on Porous Anodic Alumina

    Directory of Open Access Journals (Sweden)

    Zhu YuanYuan

    2010-01-01

    Full Text Available Abstract Porous anodic alumina (PAA has been intensively studied in past decade due to its applications for fabricating nanostructured materials. Since PAA’s pore diameter, thickness and shape vary too much, a systematical study on the methods of morphology characterization is meaningful and essential for its proper development and utilization. In this paper, we present detailed AFM, SEM and TEM studies on PAA and its evolvements with abundant microstructures, and discuss the advantages and disadvantages of each method. The sample preparation, testing skills and morphology analysis are discussed, especially on the differentiation during characterizing complex cross-sections and ultrasmall nanopores. The versatility of PAAs is also demonstrated by the diversity of PAAs’ microstructure.

  9. Rational engineering of nanoporous anodic alumina optical bandpass filters

    Science.gov (United States)

    Santos, Abel; Pereira, Taj; Law, Cheryl Suwen; Losic, Dusan

    2016-08-01

    Herein, we present a rationally designed advanced nanofabrication approach aiming at producing a new type of optical bandpass filters based on nanoporous anodic alumina photonic crystals. The photonic stop band of nanoporous anodic alumina (NAA) is engineered in depth by means of a pseudo-stepwise pulse anodisation (PSPA) approach consisting of pseudo-stepwise asymmetric current density pulses. This nanofabrication method makes it possible to tune the transmission bands of NAA at specific wavelengths and bandwidths, which can be broadly modified across the UV-visible-NIR spectrum through the anodisation period (i.e. time between consecutive pulses). First, we establish the effect of the anodisation period as a means of tuning the position and width of the transmission bands of NAA across the UV-visible-NIR spectrum. To this end, a set of nanoporous anodic alumina bandpass filters (NAA-BPFs) are produced with different anodisation periods, ranging from 500 to 1200 s, and their optical properties (i.e. characteristic transmission bands and interferometric colours) are systematically assessed. Then, we demonstrate that the rational combination of stacked NAA-BPFs consisting of layers of NAA produced with different PSPA periods can be readily used to create a set of unique and highly selective optical bandpass filters with characteristic transmission bands, the position, width and number of which can be precisely engineered by this rational anodisation approach. Finally, as a proof-of-concept, we demonstrate that the superposition of stacked NAA-BPFs produced with slight modifications of the anodisation period enables the fabrication of NAA-BPFs with unprecedented broad transmission bands across the UV-visible-NIR spectrum. The results obtained from our study constitute the first comprehensive rationale towards advanced NAA-BPFs with fully controllable photonic properties. These photonic crystal structures could become a promising alternative to traditional optical

  10. Rapid fabrication of self-ordered porous alumina with 10-/sub-10-nm-scale nanostructures by selenic acid anodizing.

    Science.gov (United States)

    Nishinaga, Osamu; Kikuchi, Tatsuya; Natsui, Shungo; Suzuki, Ryosuke O

    2013-09-25

    Anodic porous alumina has been widely investigated and used as a nanostructure template in various nanoapplications. The porous structure consists of numerous hexagonal cells perpendicular to the aluminum substrate and each cell has several tens or hundreds of nanoscale pores at its center. Because the nanomorphology of anodic porous alumina is limited by the electrolyte during anodizing, the discovery of additional electrolytes would expand the applicability of porous alumina. In this study, we report a new self-ordered nanoporous alumina formed by selenic acid (H2SeO4) anodizing. By optimizing the anodizing conditions, anodic alumina possessing 10-nm-scale pores was rapidly assembled (within 1 h) during selenic acid anodizing without any special electrochemical equipment. Novel sub-10-nm-scale spacing can also be achieved by selenic acid anodizing and metal sputter deposition. Our new nanoporous alumina can be used as a nanotemplate for various nanostructures in 10-/sub-10-nm-scale manufacturing.

  11. Vertically aligned nanowires on flexible silicone using a supported alumina template prepared by pulsed anodization

    DEFF Research Database (Denmark)

    Mátéfi-Tempfli, Stefan; Mátéfi-Tempfli, M.

    2009-01-01

    Carpets of vertically aligned nanowires on flexible substrates are successfully realized by a template method. Applying special pulsed anodization conditions, defect-free nanoporous alumina structures supported on polydimethylsiloxane (PDMS), a flexible silicone elastomer, are created. By using...

  12. Nanostructural characterization of large-scale porous alumina fabricated via anodizing in arsenic acid solution

    Science.gov (United States)

    Akiya, Shunta; Kikuchi, Tatsuya; Natsui, Shungo; Suzuki, Ryosuke O.

    2017-05-01

    Anodizing of aluminum in an arsenic acid solution is reported for the fabrication of anodic porous alumina. The highest potential difference (voltage) without oxide burning increased as the temperature and the concentration of the arsenic acid solution decreased, and a high anodizing potential difference of 340 V was achieved. An ordered porous alumina with several tens of cells was formed in 0.1-0.5 M arsenic acid solutions at 310-340 V for 20 h. However, the regularity of the porous alumina was not improved via anodizing for 72 h. No pore sealing behavior of the porous alumina was observed upon immersion in boiling distilled water, and it may be due to the formation of an insoluble complex on the oxide surface. The porous alumina consisted of two different layers: a hexagonal alumina layer that contained arsenic from the electrolyte and a pure alumina honeycomb skeleton. The porous alumina exhibited a white photoluminescence emission at approximately 515 nm under UV irradiation at 254 nm.

  13. Understanding improved osteoblast behavior on select nanoporous anodic alumina

    Directory of Open Access Journals (Sweden)

    Ni S

    2014-07-01

    Full Text Available Siyu Ni,1 Changyan Li,1 Shirong Ni,2 Ting Chen,1 Thomas J Webster3,4 1College of Chemistry, Chemical Engineering and Biotechnology, Donghua University, Shanghai, People’s Republic of China; 2Department of Pathophysiology, Wenzhou Medical University, Wenzhou, People’s Republic of China; 3Department of Chemical Engineering, College of Engineering, Northeastern University, Boston, MA, USA; 4Center of Excellence for Advanced Materials Research, King Abdulaziz University, Jeddah, Saudi Arabia Abstract: The aim of this study was to prepare different sized porous anodic alumina (PAA and examine preosteoblast (MC3T3-E1 attachment and proliferation on such nanoporous surfaces. In this study, PAA with tunable pore sizes (25 nm, 50 nm, and 75 nm were fabricated by a two-step anodizing procedure in oxalic acid. The surface morphology and elemental composition of PAA were characterized by field emission scanning electron microscopy and X-ray photoelectron spectroscopy analysis. The nanopore arrays on all of the PAA samples were highly regular. X-ray photoelectron spectroscopy analysis suggested that the chemistry of PAA and flat aluminum surfaces were similar. However, contact angles were significantly greater on all of the PAA compared to flat aluminum substrates, which consequently altered protein adsorption profiles. The attachment and proliferation of preosteoblasts were determined for up to 7 days in culture using field emission scanning electron microscopy and a Cell Counting Kit-8. Results showed that nanoporous surfaces did not enhance initial preosteoblast attachment, whereas preosteoblast proliferation dramatically increased when the PAA pore size was either 50 nm or 75 nm compared to all other samples (P<0.05. Thus, this study showed that one can alter surface energy of aluminum by modifying surface nano-roughness alone (and not changing chemistry through an anodization process to improve osteoblast density, and, thus, should be

  14. Novel structure formation at the bottom surface of porous anodic alumina fabricated by single step anodization process.

    Science.gov (United States)

    Ali, Ghafar; Ahmad, Maqsood; Akhter, Javed Iqbal; Maqbool, Muhammad; Cho, Sung Oh

    2010-08-01

    A simple approach for the growth of long-range highly ordered nanoporous anodic alumina film in H(2)SO(4) electrolyte through a single step anodization without any additional pre-anodizing procedure is reported. Free-standing porous anodic alumina film of 180 microm thickness with through hole morphology was obtained. A simple and single step process was used for the detachment of alumina from aluminum substrate. The effect of anodizing conditions, such as anodizing voltage and time on the pore diameter and pore ordering is discussed. The metal/oxide and oxide/electrolyte interfaces were examined by high resolution scanning transmission electron microscope. The arrangement of pores on metal/oxide interface was well ordered with smaller diameters than that of the oxide/electrolyte interface. The inter-pore distance was larger in metal/oxide interface as compared to the oxide/electrolyte interface. The size of the ordered domain was found to depend strongly upon anodizing voltage and time.

  15. Effect of anodizing voltage on the sorption of water molecules on porous alumina

    Energy Technology Data Exchange (ETDEWEB)

    Vrublevsky, I., E-mail: vrublevsky@bsuir.edu.by [Belarusian State University of Informatics and Radioelectronics, Department of Micro and Nanoelectronics, 220013 Minsk (Belarus); Chernyakova, K. [Belarusian State University of Informatics and Radioelectronics, Department of Micro and Nanoelectronics, 220013 Minsk (Belarus); Bund, A.; Ispas, A.; Schmidt, U. [Fachgebiet Elektrochemie und Galvanotechnik, Technische Universitaet Ilmenau, 98693 Ilmenau (Germany)

    2012-05-01

    The amount of water adsorbed on different centers on the surface of oxalic acid alumina films is a function of the anodizing voltage. It is decreased with increasing the anodizing voltage from 20 up to 50 V, came up to maximum value at 20-30 V and slightly increased at voltages above 50 V. Water adsorption by oxide films formed at voltages below 50 V can be due to the negative surface charge that is present on the alumina surface. The negative surface charge disappears in the films formed at voltages higher than 50 V, and thus, the water is adsorbed on aluminum ions in a tetrahedral and octahedral environment. The correlation between anodizing conditions of aluminum in oxalic acid and the structure and composition of anodic alumina was established by Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM), thermogravimetric and differential thermal analyses (TG/DTA).

  16. Effect of Manganese Content on the Fabrication of Porous Anodic Alumina

    Directory of Open Access Journals (Sweden)

    C. H. Voon

    2012-01-01

    Full Text Available The influence of manganese content on the formation of well-ordered porous anodic alumina was studied. Porous anodic alumina has been produced on aluminium substrate of different manganese content by single-step anodizing at 50 V in 0.3 M oxalic acid at 15°C for 60 minutes. The well-ordered pore and cell structure was revealed by subjecting the porous anodic alumina to oxide dissolution treatment in a mixture of chromic acid and phosphoric acid. It was found that the manganese content above 1 wt% impaired the regularity of the cell and pore structure significantly, which can be attributed to the presence of secondary phases in the starting material with manganese content above 1 wt%. The pore diameter and interpore distance decreased with the addition of manganese into the substrates. The time variation of current density and the thickness of porous anodic alumina also decreased as a function of the manganese content in the substrates.

  17. 超薄氧化铝模板的制备及应用%Review of the preparation and application of ultra-thin alumina mask

    Institute of Scientific and Technical Information of China (English)

    敖昕; 戴金辉; 时磊艳; 徐楠

    2011-01-01

    Large-scale arrays of nanostructures on substrates have many potential applications in areas such as electronics, optoelectronics, sensing, catalyst, high-density storage, solar cells, field emission devices and ultra-thin display devices. Here, we review a new surface nano-patterning approach in fabricating ordered nanostructures, in which ultra-thin anodic alumina membranes are used as fabrication masks. According to the fabrication method, two different types of ultra-thin alumina masks exist: attached UTAM and connected UTAM.In this paper, applications of ultra-thin alumina masks have been reviewed in recent years.%基板上大面积的有序纳米阵列,在电子学、光电子学、传感器、催化剂、太阳能电池、高密度储存、场发射设备和超薄显示设备等领域具有广阔的应用前景.综述了一种构造表面有序纳米结构的新方法--超薄氧化铝模板法.根据超薄氧化铝模板的制备方法又分为附着型和结合型.还总结了近年来该方法的应用.

  18. Excitation of anodized alumina films with a light source

    DEFF Research Database (Denmark)

    Aggerbeck, Martin; Canulescu, Stela; Rechendorff, K.;

    . The UV-VIS reflectance of Ti-doped anodized aluminium films was measured over the wavelength range of 200 nm to 900 nm. Titanium doped-anodized aluminium films with 5-15 wt% Ti were characterized. Changes in the diffuse light scattering of doped anodized aluminium films, and thus optical appearance......Optical properties of anodized aluminium alloys were determined by optical diffuse reflectance spectroscopy of such films. Samples with different concentrations of dopants were excited with a white-light source combined with an integrating sphere for fast determination of diffuse reflectance...

  19. Enhanced gas separation factors of microporous polymer constrained in the channels of anodic alumina membranes

    Science.gov (United States)

    Chernova, Ekaterina; Petukhov, Dmitrii; Boytsova, Olga; Alentiev, Alexander; Budd, Peter; Yampolskii, Yuri; Eliseev, Andrei

    2016-08-01

    New composite membranes based on porous anodic alumina films and polymer of intrinsic microporosity (PIM-1) have been prepared using a spin-coating technique. According to scanning electron microscopy, partial penetration of polymer into the pores of alumina supports takes place giving rise to selective polymeric layers with fiber-like microstructure. Geometric confinement of rigid PIM-1 in the channels of anodic alumina causes reduction of small-scale mobility in polymeric chains. As a result, transport of permanent gases, such as CH4, becomes significantly hindered across composite membranes. Contrary, the transport of condensable gases (CO2, C4H10), did not significantly suffer from the confinement due to high solubility in the polymer matrix. This strategy enables enhancement of selectivity towards CO2 and C4H10 without significant loss of the membrane performance and seems to be prospective for drain and sweetening of natural gas.

  20. Blue luminescence in porous anodic alumina films: the role of the oxalic impurities

    CERN Document Server

    Gao Tao; Zhang Li

    2003-01-01

    Porous anodic alumina (PAA) films with ordered nanopore arrays have been prepared by electrochemically anodizing aluminium in oxalic acid solutions, and the role of the oxalic impurities in the optical properties of PAA films has been discussed. Photoluminescence (PL) measurements show that the PAA films obtained have a blue PL band with a peak position at around 470 nm; the oxalic impurities, incorporated in the PAA films during the anodization processes and already existing in them, could be being transformed into PL centres and hence responsible for this PL emission.

  1. Synthesis of aluminum oxy-hydroxide nanofibers from porous anodic alumina.

    Science.gov (United States)

    Jha, Himendra; Kikuchi, Tatsuya; Sakairi, Masatoshi; Takahashi, Hideaki

    2008-10-01

    A novel method for the synthesis of aluminum oxy-hydroxide nanofibers from a porous anodic oxide film of aluminum is demonstrated. In the present method, the porous anodic alumina not only acts as a template, but also serves as the starting material for the synthesis. The porous anodic alumina film is hydrothermally treated for pore-sealing, which forms aluminum oxy-hydroxide inside the pores of the oxide film as well as on the surface of the film. The hydrothermally sealed porous oxide film is immersed in the sodium citrate solution, which selectively etches the porous aluminum oxide from the film, leaving the oxy-hydroxide intact. The method is simple and gives highly uniform aluminum oxy-hydroxide nanofibers. Moreover, the diameter of the nanofibers can be controlled by controlling the pore size of the porous anodic alumina film, which depends on the anodizing conditions. Nanofibers with diameters of about 38-85 nm, having uniform shape and size, were successfully synthesized using the present method.

  2. Structure and Optical Properties of thin Porous Anodic Alumina Films Synthesized on a Glass Surface

    Science.gov (United States)

    Valeev, R. G.; Petukhov, D. I.; Kriventsov, V. V.

    The structure and luminescent properties of thin nanoporous aluminum oxide films obtained by anodization of aluminum films thermally deposited on glass have been investigated. The pore size and the interpore distance depend on the anodization voltage. For all studied samples the highest emission intensity obtained at the excitation wavelength equal to 330 nm. This behavior of luminescence curves caused by defect F+ luminescent centers (O- oxygen vacancies). The presence of porous alumina films on the glass surface increases the optical absorption in the visible light region. The oscillations on the spectra are caused by Fabry-Perot interference on the anodic alumina oxide film/glass interface. The suggested technique can be used for obtaining porous aluminum oxide films on other substrates, including Indium-Tin-Oxide, and can be applied in the technology of light-emitting devices and infrared-visible-ultraviolet detectors.

  3. Surface of Alumina Films after Prolonged Breakdowns in Galvanostatic Anodization

    Directory of Open Access Journals (Sweden)

    Christian Girginov

    2011-01-01

    Full Text Available Breakdown phenomena are investigated at continuous isothermal (20∘C and galvanostatic (0.2–5 mA cm−2 anodizing of aluminum in ammonium salicylate in dimethylformamide (1 M AS/DMF electrolyte. From the kinetic (-curves, the breakdown voltage ( values are estimated, as well as the frequency and amplitude of oscillations of formation voltage ( at different current densities. The surface of the aluminum specimens was studied using atomic force microscopy (AFM. Data on topography and surface roughness parameters of the electrode after electric breakdowns are obtained as a function of anodization time. The electrode surface of anodic films, formed with different current densities until the same charge density has passed (2.5 C cm−2, was assessed. Results are discussed on the basis of perceptions of avalanche mechanism of the breakdown phenomena, due to the injection of electrons and their multiplication in the volume of the film.

  4. Nanoporous hard data: optical encoding of information within nanoporous anodic alumina photonic crystals

    Science.gov (United States)

    Santos, Abel; Law, Cheryl Suwen; Pereira, Taj; Losic, Dusan

    2016-04-01

    Herein, we present a method for storing binary data within the spectral signature of nanoporous anodic alumina photonic crystals. A rationally designed multi-sinusoidal anodisation approach makes it possible to engineer the photonic stop band of nanoporous anodic alumina with precision. As a result, the transmission spectrum of these photonic nanostructures can be engineered to feature well-resolved and selectively positioned characteristic peaks across the UV-visible spectrum. Using this property, we implement an 8-bit binary code and assess the versatility and capability of this system by a series of experiments aiming to encode different information within the nanoporous anodic alumina photonic crystals. The obtained results reveal that the proposed nanosized platform is robust, chemically stable, versatile and has a set of unique properties for data storage, opening new opportunities for developing advanced nanophotonic tools for a wide range of applications, including sensing, photonic tagging, self-reporting drug releasing systems and secure encoding of information.Herein, we present a method for storing binary data within the spectral signature of nanoporous anodic alumina photonic crystals. A rationally designed multi-sinusoidal anodisation approach makes it possible to engineer the photonic stop band of nanoporous anodic alumina with precision. As a result, the transmission spectrum of these photonic nanostructures can be engineered to feature well-resolved and selectively positioned characteristic peaks across the UV-visible spectrum. Using this property, we implement an 8-bit binary code and assess the versatility and capability of this system by a series of experiments aiming to encode different information within the nanoporous anodic alumina photonic crystals. The obtained results reveal that the proposed nanosized platform is robust, chemically stable, versatile and has a set of unique properties for data storage, opening new opportunities for

  5. Simulation and experiment of substrate aluminum grain orientation dependent self-ordering in anodic porous alumina

    Science.gov (United States)

    Cheng, Chuan; Ng, K. Y.; Aluru, N. R.; Ngan, A. H. W.

    2013-05-01

    Recent experiments have indicated a strong influence of the substrate grain orientation on the self-ordering in anodic porous alumina. Anodic porous alumina with straight pore channels grown in a stable, self-ordered manner is formed on (001) oriented Al grain, while disordered porous pattern is formed on (101) oriented Al grain with tilted pore channels growing in an unstable manner. In this work, numerical simulation of the pore growth process is carried out to understand this phenomenon. The rate-determining step of the oxide growth is assumed to be the Cabrera-Mott barrier at the oxide/electrolyte (o/e) interface, while the substrate is assumed to determine the ratio β between the ionization and oxidation reactions at the metal/oxide (m/o) interface. By numerically solving the electric field inside a growing porous alumina during anodization, the migration rates of the ions and hence the evolution of the o/e and m/o interfaces are computed. The simulated results show that pore growth is more stable when β is higher. A higher β corresponds to more Al ionized and migrating away from the m/o interface rather than being oxidized, and hence a higher retained O:Al ratio in the oxide. Experimentally measured oxygen content in the self-ordered porous alumina on (001) Al is indeed found to be about 3% higher than that in the disordered alumina on (101) Al, in agreement with the theoretical prediction. The results, therefore, suggest that ionization on (001) Al substrate is relatively easier than on (101) Al, and this leads to the more stable growth of the pore channels on (001) Al.

  6. Highly Ordered Carbon Nanotube Arrays with Open Ends Grown in Anodic Alumina Nanoholes

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    Highly ordered multiwalled carbon nanotube arrays were fabricated by pyrolysis of acetylene within anodic alumina templates.Nanotubes are very uniform in diameter and open at both ends. High resolution transmission electron microscopy and electron diffraction analysis show that the carbon nanotubes are well graphitized. These standing and open carbon nanotubes are possible to offer a potential elegant technique for electron emitting devices,chemical functionalization and nanotube composites.

  7. Structure of the carbon nanofilaments formed by liquid phase carbonization in porous anodic alumina template

    OpenAIRE

    Habazaki, H.; Kiriu, M.; M. Hayashi; Konno, H.

    2007-01-01

    Platelet structure carbon nanofilaments of ~30 nm in diameter have been prepared by heating a mixture of porous anodic alumina template and poly(vinyl)chloride (PVC) powders in an argon atmosphere, and the change in their structure and morphology with heat treatment temperature, ranging from 600 to 2800 °C, has been examined using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and nitrogen gas adsorption measurements. The diameter of the ca...

  8. Effects of etching time on the bottom surface morphology of ultrathin porous alumina membranes for use as masks

    Science.gov (United States)

    Yang, Sun A.; Choi, Yong Chan; Bu, Sang Don

    2012-11-01

    We investigated the effect of etching time on the bottom surface morphologies of ultrathin porous alumina membranes (UT-PAMs) anodized in oxalic and phosphoric acid. The morphology of the bottom surface clearly changed and a unique surface undulation was observed during the etching process. Such an undulation regarding the bottom surface is attributed to the different etching rates between the dome-shaped barrier layer and the hexagonal cell walls. The results suggest that the bottom morphology of UT-PAMs formed after the barrier layer is opened significantly affects the contact area of the bottom side with the substrate. During the initial stage of the opening process for the barrier layer, the porous section will contact the substrate rather than the walls. However, as the etching time increases, the height of the porous section becomes considerably lower than that of the walls, which means that the walls will contact the substrate with a gap between the pores and the substrate. Based on our experimental results, we propose a possible schematic diagram describing the effects of UT-PAMs with differently-shaped bottom surfaces on the shapes of fabricated nanodots when the UT-PAMs are used as masks.

  9. Anodic behaviour of oxidised Ni-Fe alloys in cryolite-alumina melts

    Energy Technology Data Exchange (ETDEWEB)

    Chapman, Vivien, E-mail: v.singleton@student.unsw.edu.a [Centre for Electrochemical and Mineral Processing, School of Chemical Engineering, University of New South Wales, Sydney 2052 (Australia); Welch, Barry J. [Welbank Consulting Ltd., PO Box 207, Whitianga 3542 (New Zealand); Skyllas-Kazacos, Maria [Centre for Electrochemical and Mineral Processing, School of Chemical Engineering, University of New South Wales, Sydney 2052 (Australia)

    2011-01-01

    Nickel-iron alloys have been identified as promising inert anode candidates for the Hall-Heroult process. In this study, binary Ni-Fe alloys of various compositions were subjected to short-term galvanostatic electrolysis in a cryolite-alumina bath at 960 {sup o}C. Prior to electrolysis, the anodes were oxidised at 800 {sup o}C for 48 h, forming a protective scale. Fe{sub 2}O{sub 3}, Ni{sub x}Fe{sub 3-x}O{sub 4} and Ni{sub x}Fe{sub 1-x}O were identified as the major scale components using a combination of X-ray diffraction (XRD) analysis and energy dispersive X-ray spectroscopy (EDX). Anodes having Ni content of 50-65 wt% performed adequately during short-term electrolysis, operating at a steady potential of 3-3.5 V vs. AlF{sub 3}/Al. Overall, it was found that the pre-formed oxide scale was effective in reducing anode wear and fluoridation. In the absence of a pre-formed scale, anodes were shown to undergo appreciable internal corrosion and/or passivation due to metal fluoride formation. Analysis of the anodes following electrolysis was performed using XRD and electron microprobe analysis (EPMA).

  10. Regularity control of porous anodic alumina and photodegradation activity of highly ordered titania nanostructures

    Institute of Scientific and Technical Information of China (English)

    LIU Xiang-zhi; XU Ming-xia; TIAN Yu-ming; SHANG Meng; ZHANG Ping

    2006-01-01

    A two-step anodizing process was used to prepare wide-range highly ordered porous anodic alumina membrane (PAA) in the electrolyte of oxalic acid. The effects of anodic voltage,anodizing time,size of aluminium foil and additives on the regularity of PAA membrane were also studied in the process of two-step anodization. The template method was combined with the sol-electrophoresis deposition and sol-gel method respectively to prepare highly ordered titania nanostructures. The diameter and length of the obtained nanostructures were determined by the pore size and depth of the PAA template. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) were used to characterize the morphology and phase structure of the PAA template and the titania nanostructures. The results show that the anodizing time and the additive of ethanol have a great effect on the regularity of PAA template. This can be explained from the self-organized process and the current density theory. A theoretical model based on the self-organized process was established to discuss the formation mechanism of PAA template from the chemical perspective. The titania nanostructures prepared with this method has a high specific surface area. Furthermore,the photocatalytic activity of titania nanostructures on methyl orange were studied. Compared with ordinary titania membranes,the titania nanostructures synthesized with this method have higher photodegradation activity.

  11. Ordered three-dimensional interconnected nanoarchitectures in anodic porous alumina

    Science.gov (United States)

    Martín, Jaime; Martín-González, Marisol; Fernández, Jose Francisco; Caballero-Calero, Olga

    2014-01-01

    Three-dimensional nanostructures combine properties of nanoscale materials with the advantages of being macro-sized pieces when the time comes to manipulate, measure their properties, or make a device. However, the amount of compounds with the ability to self-organize in ordered three-dimensional nanostructures is limited. Therefore, template-based fabrication strategies become the key approach towards three-dimensional nanostructures. Here we report the simple fabrication of a template based on anodic aluminum oxide, having a well-defined, ordered, tunable, homogeneous 3D nanotubular network in the sub 100 nm range. The three-dimensional templates are then employed to achieve three-dimensional, ordered nanowire-networks in Bi2Te3 and polystyrene. Lastly, we demonstrate the photonic crystal behavior of both the template and the polystyrene three-dimensional nanostructure. Our approach may establish the foundations for future high-throughput, cheap, photonic materials and devices made of simple commodity plastics, metals, and semiconductors. PMID:25342247

  12. Formation and disruption of current paths of anodic porous alumina films by conducting atomic force microscopy

    Energy Technology Data Exchange (ETDEWEB)

    Oyoshi, K., E-mail: oyoshi.keiji@nims.go.jp [National Institute for Materials Science, 1-2-1 Sengen, Tsukuba 305-0047 (Japan); Nigo, S.; Inoue, J.; Sakai, O.; Kitazawa, H.; Kido, G. [National Institute for Materials Science, 1-2-1 Sengen, Tsukuba 305-0047 (Japan)

    2010-11-15

    Anodic porous alumina (APA) films have a honeycomb cell structure of pores and a voltage-induced bi-stable switching effect. We have applied conducting atomic force microscopy (CAFM) as a method to form and to disrupt current paths in the APA films. A bi-polar switching operation was confirmed. We have firstly observed terminals of current paths as spots or areas typically on the center of the triangle formed by three pores. In addition, though a part of the current path showed repetitive switching, most of them were not observed again at the same position after one cycle of switching operations in the present experiments. This suggests that a part of alumina structure and/or composition along the current paths is modified during the switching operations.

  13. Unifying the templating effects of porous anodic alumina on metallic nanoparticles for carbon nanotube synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Haase, Mark R., E-mail: Mark.R.Haase@gmail.com, E-mail: haasemr@mail.uc.edu; Alvarez, Noe T.; Malik, Rachit; Schulz, Mark; Shanov, Vesselin [580 Engineering Research Center, Department of Biomedical, Chemical and Environmental Engineering (United States)

    2015-09-15

    Carbon nanotubes (CNTs) are a promising material for many applications, due to their extraordinary properties. Some of these properties vary in relation to the diameter of the nanotubes; thus, precise control of CNT diameter can be critical. Porous anodic alumina (PAA) membranes have been successfully used to template electrodeposited catalyst. However, the catalysts used in CNT synthesis are frequently deposited with more precise techniques, such as electron beam deposition. We test the efficacy of PAA as a template for electron beam-deposited catalyst by studying the diameter distribution of CNTs grown catalyst of various thicknesses supported by PAA. These are then compared by ANOVA to the diameter distributions of CNTs grown on metal catalyst supported by a conventional alumina film. These results also allow a unified description of two templating effects, the more common particles-in-pores model, and the recently described particles-between-pores.

  14. Synthesis and Photoluminescence Enhancement of Silver Nanoparticles Decorated Porous Anodic Alumina

    Institute of Scientific and Technical Information of China (English)

    Song Ye; Yidong Hou; Renyi Zhu; Shulong Gu; Jingquan Wang; Zhiyou Zhang; Sha Shi; Jinglei Du

    2011-01-01

    Silver nanoparticles (Ag NPs) were successfully assembled in porous anodic alumina (AAO) templates via a green silver mirror reaction. The Ag NPs/AAO composite templates then were characterized by field emission scanning electron microscopy (FESEM), energy-dispersive X-ray microanalysis (EDX), and X-ray diffraction (XRD). Furthermore, the photoluminescence (PL) properties were also investigated. Compared with the blank AAO, the PL intensity of Ag NPs/AAO templates are enhanced and the maximum enhancement is 2.58 times. Based on the local electric field enhancement effect, the theoretical values were also deduced, which are basically coincident with the experimental.

  15. Fabrication and characterization of mesoporous silica nanochannels inside the channels of anodic alumina membrane

    Directory of Open Access Journals (Sweden)

    Moataz M. Mekawy

    2016-03-01

    Full Text Available Brij type surfactants (CnEOx that have different chemical structures were used to fabricate 3D Mesoporous Silica Nanochannels (MSN inside the channels of Anodic Alumina Membrane (AAM under acidic conditions. The fabricated 3D MSN were characterized using TEM-ED, SEM, Small angle XRD, and N2 isotherm. Results revealed that the synthesis of ordered 3D cubic Im3m mesostructures can be formed with tunable pore diameters varied from 4.0 to 4.9 nm that are partially affected with the length of ethylene oxide (EO group in the template surfactant.

  16. Porous anodic alumina on galvanically grown PtSi layer for application in template-assisted Si nanowire growth

    Directory of Open Access Journals (Sweden)

    Stavrinidou Eleni

    2011-01-01

    Full Text Available Abstract We report on the fabrication and morphology/structural characterization of a porous anodic alumina (PAA/PtSi nano-template for use as matrix in template-assisted Si nanowire growth on a Si substrate. The PtSi layer was formed by electroless deposition from an aqueous solution containing the metal salt and HF, while the PAA membrane by anodizing an Al film deposited on the PtSi layer. The morphology and structure of the PtSi layer and of the alumina membrane on top were studied by Scanning and High Resolution Transmission Electron Microscopies (SEM, HRTEM. Cross sectional HRTEM images combined with electron diffraction (ED were used to characterize the different interfaces between Si, PtSi and porous anodic alumina.

  17. Plasmonic properties of gold-coated nanoporous anodic alumina with linearly organized pores

    Indian Academy of Sciences (India)

    Dheeraj Pratap; P Mandal; S Anantha Ramakrishna

    2014-12-01

    Anodization of aluminium surfaces containing linearly oriented scratches leads to the formation of nanoporous anodic alumina (NAA) with the nanopores arranged preferentially along the scratch marks. NAA, when coated with a thin gold film, support plasmonic resonances. Dark-field spectroscopy revealed that gold-coated NAA with such linearly arranged pores shows a polarization-dependent scattering, that is larger when the incident light is polarized parallel to the scratch direction than when polarized perpendicular to the scratch direction. Fluorescence studies from rhodamine-6G (R6G) molecules dissolved in polymethylmethacrylate (PMMA) and deposited on these NAA templates showed that fluorescence can be strongly enhanced with the bare NAA due to multiple light scattering in the NAA, while fluorescence from the molecules deposited on gold-coated NAA is strongly quenched due to the strong plasmonic coupling.

  18. Micropolarizer of Ordered Ni Nanowire Arrays Embedded in Porous Anodic Alumina Membrane

    Institute of Scientific and Technical Information of China (English)

    PANG Yan-Tao; MENG Guo-Wen; SHAN Wen-Jun; FANG Qi; ZHANG Li-De

    2003-01-01

    A micropolarizer of nickel nanowire arrays within an anodic alumina membrane (AAM) was fabricated by an-odization of pure Al and electrodeposition of Ni, respectively. X-ray diffraction, scanning electron microscopy and transmission-electron microscopy reveal that the nanowires are polycrystal and have an average diameter of 70 nm. Spectrophotometer measurements show that the nickel nanowire arrays embedded in the AAM can only transmit polarized light vertical to the wires. An extinction ratio of 25 to 30 dB and an average insertion loss of 1.07dB in the wavelength range of l-2.5fj.rn were obtained, respectively. Thus, Ni nanowire/AAM can be used as a wire grid type micropolarizer.

  19. The effect of sulfuric acid on pore initiation in anodic alumina formed in oxalic acid

    Directory of Open Access Journals (Sweden)

    Behnam Hafezi

    2014-07-01

    Full Text Available In this work, a tracer study on pore initiation in anodic alumina in oxalic acid was performed. Effects of some experimental parameters such as applied electrical potential, electrolyte composition and heat pretreatment were evaluated. Electrochemical and morphological experiments were performed using potentiostatic anodizing and scanning electron microscopy (SEM techniques, respectively. Effect of electrolyte composition on current density was discussed. In various electrical potentials, electrolyte composition had different effects on current density. Addition of sulfuric acid into oxalic acid increased porosity. Also, distribution of pore size and pore diameter were influenced by presence of sulfuric acid. Effect of electrolyte composition on the morphology of aluminum surface layer depended on the electric potential. Current density and porosity of aluminum surface layer was decreased by heat pretreatment.

  20. Polarization properties of porous anodic alumina with Y-branched Cu nanowires

    Institute of Scientific and Technical Information of China (English)

    Xuejun Su; Lichun Zhang; Qingshan Li; Dechun Liang

    2008-01-01

    @@ Porous anodic alumina (PAA) templates with branch structure are fabricated by the two-step anodic oxidation processes, and then the Y-branched Cu nanowires are synthesized in the templates using an alternating current (AC) deposition method. We observe the morphology image of the samples by scanning electron microscopy (SEM), and measure the transmission spectrum and the polarization spectrum of the samples by the spectrophotometer. The results show that PAA films with Y-branched Cu nanowires have better transmittance in the near infrared region. An extinction ratio of 15-18 dB and an insertion loss of 0.1-0.4 dB are obtained in this region. Therefore PAA with Y-branched Cu nanowires can be used as a near-infrared micropolarizer, and this kind of micropolarizer would have a promising future in the field of photoelectricity integration.

  1. Structural and optical characterizations of porous anodic alumina-aluminum nanocomposite films on borofloat substrates

    Science.gov (United States)

    Arslan, Hande Cavus; Yusufoglu, Ibrahim; Aslan, Mustafa M.

    2014-07-01

    Structural and optical properties of the porous anodic alumina (PAA)-aluminum (Al) nanocomposite and the PAA-nanostructured films on borofloat substrates are studied. The films are fabricated by the anodization of 170- to 200- and 295- to 330-nm-thick Al sputtered onto the borofloat. The anodization process is stopped at different times in order to form the PAA-Al nanocomposite films with different layer thicknesses. Then, the pore widening is applied to 189- to 210- and 430- to 495-nm-thick PAA films in 5- and 10-min intervals, respectively. The structural properties of the films are characterized by a scanning electron microscopy. The nanocomposite films are also characterized optically by total reflection and directional transmission measurements in the wavelength range between 250 and 800 nm. Our results indicate that controlling the thicknesses of both Al and the PAA layers by anodization time and the morphology of the nanostructures by chemical etching duration in the PAA layer provides unique PAA-Al nanocomposite films with desired optical properties.

  2. Analysis of nanopore arrangement and structural features of anodic alumina layers formed by two-step anodizing in oxalic acid using the dedicated executable software

    Science.gov (United States)

    Zaraska, Leszek; Stępniowski, Wojciech J.; Sulka, Grzegorz D.; Ciepiela, Eryk; Jaskuła, Marian

    2014-02-01

    Anodic porous alumina layers were fabricated by a two-step self-organized anodization in 0.3 M oxalic acid under various anodizing potentials ranging from 30 to 60 V at two different temperatures (10 and 17 ∘C). The effect of anodizing conditions on structural features and pore arrangement of AAO was investigated in detail by using the dedicated executable publication combined with ImageJ software. With increasing anodizing potential, a linear increase of the average pore diameter, interpore distance, wall thickness and barrier layer thickness, as well as a decrease of the pore density, were observed. In addition, the higher pore diameter and porosity values were obtained for samples anodized at the elevated temperature, independently of the anodizing potential. A degree of pore order was investigated on the basis of Delaunay triangulations (defect maps) and calculation of pair distribution or angle distribution functions (PDF or ADF), respectively. All methods confirmed that in order to obtain nanoporous alumina with the best, hexagonal pore arrangement, the potential of 40 V should be applied during anodization. It was confirmed that the dedicated executable publication can be used to a fast and complex analysis of nanopore arrangement and structural features of nanoporous oxide layers.

  3. Detailed Observation of Cell Junction in Anodic Porous Alumina with Square Cells

    Science.gov (United States)

    Asoh, Hidetaka; Ono, Sachiko; Hirose, Tomohito; Takatori, Ikuo; Masuda, Hideki

    2004-09-01

    The local structure of a cell junction in anodic porous alumina with square cells was studied by transmission electron microscopy (TEM), field-emission scanning electron microscopy (FE-SEM) and atomic force microscopy (AFM). The initiation of a square lattice pattern, which is different from a normal hexagonal cell arrangement, induced the characteristic growth of a porous structure. The obtained oxide film was formed by a close-packed array of square cells following the initiation. The shape of the pores changed from circular to square corresponding to the transformation of the cell structure at the steady state. The incorporation of unoxidized aluminum into the oxide film and the generation of voids were observed at the fourfold point of the cell junction. The height of the protrusions of the aluminum substrate at the cell junction was considerably larger than that of protrusions formed in naturally occurring anodic porous alumina with hexagonal cells. These specific features were thought to be caused by the inhomogeneous distribution of current at the square pore base.

  4. Excitation and emission processes of Tb{sup 3+} in porous anodic alumina

    Energy Technology Data Exchange (ETDEWEB)

    Dabboussi, S. [Unite de recherche de Spectroscopie Raman, Departement de Physique, Faculte des Sciences de Tunis, Elmanr 2092, Tunis (Tunisia); Elhouichet, H. [Unite de recherche de Spectroscopie Raman, Departement de Physique, Faculte des Sciences de Tunis, Elmanr 2092, Tunis (Tunisia)], E-mail: habib.elhouichet@fst.rnu.tn; Bouzidi, C. [Unite de recherche de Spectroscopie Raman, Departement de Physique, Faculte des Sciences de Tunis, Elmanr 2092, Tunis (Tunisia); Maliarevich, G.K.; Gaponenko, N.V. [Belarusian State University of Informatics and Radioelectronics, P. Browki St. 6, 220013 Minsk (Belarus); Oueslati, M. [Unite de recherche de Spectroscopie Raman, Departement de Physique, Faculte des Sciences de Tunis, Elmanr 2092, Tunis (Tunisia)

    2009-01-15

    The strong photoluminescence (PL) of porous anodic alumina (PAA) with terbium deposition is reported. PAA, which has a regular pore morphology, is considered an effective template for fabricating luminescent composites. Tb was deposited onto PAA films by immersion in alcoholic solution with terbium chloride followed by heat treatment. The PL spectra demonstrate typical bands of Tb{sup 3+} corresponding to {sup 5}D{sub 4} {yields} {sup 7}F{sub j} (j = 3, 4, 5, 6,) electron transition, with the maximum at 18,360 cm{sup -1} ({sup 5}D{sub 4} {yields} {sup 7}F{sub 5}). The PL mechanism of Tb{sup 3+} was systematically studied with annealing temperature. The non-radiative relaxation channel is provided by OH hydroxyls at the surface of porous anodic alumina and, after annealing at 900 deg. C, the PL yield is highly improved. The PL intensity of Tb{sup 3+} increases with laser power and a saturation phenomenon, associated with the ratio of Tb{sup 3+} to Tb{sup 4+} ions, is observed at approximately 90 W/cm{sup 2}. Based on a theoretical model, the optical cross-section {sigma} of terbium in PAA is estimated, with a value close to that of other porous materials doped with the rare-earth elements.

  5. Electrodeposition of photocatalytic TiO2 film on surface of alumina prepared by anodic oxidation

    Institute of Scientific and Technical Information of China (English)

    ZHANG Xin-yu; CHEN Tie-qun

    2004-01-01

    A new electrochemical method to prepare photocatalytic TiO2 thin film was developed, by which the TiO2 was electrodeposited on surface of alumina by AC electrolysis in solution consisting of K2 [TiO(C2O4 )2] and C2H2O4. The deposited TiO2 thin film was primarily characterized by X-ray diffraction (XRD), scanning electronic microscopy (SEM) and energy dispersive spectrum (EDS) methods. The photocatalytic properties of this film were also studied by the photocatalytic degradation of methyl orange. The results show that the TiO2 film electrodeposited by this method is mainly in amorphous and with a little crystalline component mixed anatase and rutile. The surface of the alumina prepared by anodic oxidation is porous and the TiO2 electrodeposited on it is scattered and incompact. TiO2 thin film fixed on the surface of alumina shows photocatalytic activity to the degradation of methyl orange.

  6. Tribocorrosion Behavior of Aluminum/Alumina Composite Manufactured by Anodizing and ARB Processes

    Science.gov (United States)

    Jamaati, Roohollah; Toroghinejad, Mohammad Reza; Szpunar, Jerzy A.; Li, Duanjie

    2011-12-01

    In the present work, tribocorrosion behavior of Al/Al2O3 composite strips manufactured by anodizing and accumulative roll bonding (ARB) processes was investigated. The alumina quantity was 0.48, 1.13, and 3.55 vol.% in the aluminum matrix. Tribocorrosion experiments were conducted using a ball-on-plate tribometer, where the sliding contact was fully immersed in 1 wt.% NaCl solution. The composite sample served as a working electrode and its open circuit potential (OCP) was monitored before, during, and after sliding. In order to characterize the electrochemical behavior of the surface before and after sliding electrochemical impedance spectroscopy (EIS) was used and wear was also measured. Furthermore, the influence of quantity and distribution of reinforcement particles in the matrix on OCP and EIS was evaluated. It was found that the quantity, shape, size, and dispersion of alumina particles in the aluminum matrix strongly affected the measured tribocorrosion characteristics. The results showed that inhomogeneous, lower quantity, fine, and acicular-shape alumina particles cause serious materials loss in tribocorrosion process.

  7. CFD simulation of effect of anode configuration on gas-liquid flow and alumina transport process in an aluminum reduction cell

    Institute of Scientific and Technical Information of China (English)

    詹水清; 李茂; 周孑民; 杨建红; 周益文

    2015-01-01

    Numerical simulations of gas–liquid two-phase flow and alumina transport process in an aluminum reduction cell were conducted to investigate the effects of anode configurations on the bath flow, gas volume fraction and alumina content distributions. An Euler–Euler two-fluid model was employed coupled with a species transport equation for alumina content. Three different anode configurations such as anode without a slot, anode with a longitudinal slot and anode with a transversal slot were studied in the simulation. The simulation results clearly show that the slots can reduce the bath velocity and promote the releasing of the anode gas, but can not contribute to the uniformity of the alumina content. Comparisons of the effects between the longitudinal and transversal slots indicate that the longitudinal slot is better in terms of gas–liquid flow but is disadvantageous for alumina mixing and transport process due to a decrease of anode gas under the anode bottom surface. It is demonstrated from the simulations that the mixing and transfer characteristics of alumina are controlled to great extent by the anode gas forces while the electromagnetic forces (EMFs) play the second role.

  8. Pyrite oxidation in the presence of hematite and alumina: II. Effects on the cathodic and anodic half-cell reactions.

    Science.gov (United States)

    Tabelin, Carlito Baltazar; Veerawattananun, Suchol; Ito, Mayumi; Hiroyoshi, Naoki; Igarashi, Toshifumi

    2017-03-01

    The oxidative dissolution of pyrite is an important process in the redox recycling of iron (Fe) and is well-known for its role in the formation of acid mine drainage (AMD), which is considered as the most serious and widespread problem after the closure of mines and mineral processing operations. Because this process requires the movement of electrons, common metal oxides in nature that have either semiconducting (e.g., hematite) or insulating (e.g., alumina) properties may have strong effects on it. In this study, changes in the electrochemical behavior of pyrite in the presence of hematite and alumina were investigated. Results showed that the formation of surface-bound species directly influenced the anodic and cathodic half-cell reactions as well as the transfer of electrons between these sites. Pyrite pretreated in the air became anodically more reactive than that pretreated in oxygenated water, but the type of oxidizing media had little effect on the cathodic half-cell reaction. The presence of hematite and alumina during pretreatment also had strong effects on the electrochemical properties of pyrite. Chronoamperometry measurements suggest that hematite and alumina enhanced the anodic half-cell reaction but suppressed the cathodic half-cell reaction of pyrite oxidation. Increased anodic half-cell reaction in the presence of hematite could be attributed to electron "bridging" and catalytic effects of this mineral. In contrast, the effects of alumina on the anodic half-cell reaction were indirect and could be explained by the formation of Fe(3+)-oxyhydroxide surface species during pretreatment. Suppression of the cathodic half-cell reaction by both minerals was attributed to their "protective" effect on cathodic sites. Our results also point to the cathodic half-cell reaction as the rate determining-step of the overall oxidative dissolution process.

  9. Formation and Entrapment of Tris(8-hydroxyquinolinealuminum from 8-Hydroxyquinoline in Anodic Porous Alumina

    Directory of Open Access Journals (Sweden)

    Shohei Yamaguchi

    2016-08-01

    Full Text Available The formation and entrapment of tris(8-hydroxyquinolinealuminum (Alq3 molecules on the surface of anodic porous alumina (APA immersed in an ethanol solution of 8-hydroxyquinoline (HQ were investigated by absorption, fluorescence, and Raman spectroscopies. The effects of the selected APA preparation conditions (galvanostatic or potentiostatic anodization method, anodizing current and voltage values, one- or two-step anodizing process, and sulfuric acid electrolyte concentration on the adsorption and desorption of Alq3 species were examined. Among the listed parameters, sulfuric acid concentration was the most important factor in determining the Alq3 adsorption characteristics. The Alq3 content measured after desorption under galvanostatic conditions was 2.5 times larger than that obtained under potentiostatic ones, regardless of the adsorbed quantities. The obtained results suggest the existence of at least two types of adsorption sites on the APA surface characterized by different magnitudes of the Alq3 bonding strength. The related fluorescence spectra contained two peaks at wavelengths of 480 and 505 nm, which could be attributed to isolated Alq3 species inside nanovoids and aggregated Alq3 clusters in the pores of APA, respectively. The former species were attached to the adsorption sites with higher binding energies, whereas the latter ones were bound to the APA surface more weakly. Similar results were obtained for the Alq3 species formed from the HQ solution, which quantitatively exceeded the number of the Alq3 species adsorbed from the Alq3 solution. Alq3 molecules were formed in the HQ solution during the reaction of HQ molecules with the Al3+ ions in the oxide dissolution zone near the oxide/electrolyte interface through the cracks and the Al3+ ions adsorbed on surface of pore and cracks. In addition, it was suggested that HQ molecules could penetrate the nanovoids more easily than Alq3 species because of their smaller sizes, which

  10. Formation and Entrapment of Tris(8-hydroxyquinoline)aluminum from 8-Hydroxyquinoline in Anodic Porous Alumina.

    Science.gov (United States)

    Yamaguchi, Shohei; Matsui, Kazunori

    2016-08-24

    The formation and entrapment of tris(8-hydroxyquinoline)aluminum (Alq₃) molecules on the surface of anodic porous alumina (APA) immersed in an ethanol solution of 8-hydroxyquinoline (HQ) were investigated by absorption, fluorescence, and Raman spectroscopies. The effects of the selected APA preparation conditions (galvanostatic or potentiostatic anodization method, anodizing current and voltage values, one- or two-step anodizing process, and sulfuric acid electrolyte concentration) on the adsorption and desorption of Alq₃ species were examined. Among the listed parameters, sulfuric acid concentration was the most important factor in determining the Alq₃ adsorption characteristics. The Alq₃ content measured after desorption under galvanostatic conditions was 2.5 times larger than that obtained under potentiostatic ones, regardless of the adsorbed quantities. The obtained results suggest the existence of at least two types of adsorption sites on the APA surface characterized by different magnitudes of the Alq₃ bonding strength. The related fluorescence spectra contained two peaks at wavelengths of 480 and 505 nm, which could be attributed to isolated Alq₃ species inside nanovoids and aggregated Alq₃ clusters in the pores of APA, respectively. The former species were attached to the adsorption sites with higher binding energies, whereas the latter ones were bound to the APA surface more weakly. Similar results were obtained for the Alq₃ species formed from the HQ solution, which quantitatively exceeded the number of the Alq₃ species adsorbed from the Alq₃ solution. Alq₃ molecules were formed in the HQ solution during the reaction of HQ molecules with the Al(3+) ions in the oxide dissolution zone near the oxide/electrolyte interface through the cracks and the Al(3+) ions adsorbed on surface of pore and cracks. In addition, it was suggested that HQ molecules could penetrate the nanovoids more easily than Alq₃ species because of their smaller

  11. Enhancing the platinum atomic layer deposition infiltration depth inside anodic alumina nanoporous membrane

    Energy Technology Data Exchange (ETDEWEB)

    Vaish, Amit, E-mail: anv@udel.edu; Krueger, Susan; Dimitriou, Michael; Majkrzak, Charles [National Institute of Standards and Technology (NIST) Center for Neutron Research, Gaithersburg, MD 20899-8313 (United States); Vanderah, David J. [Institute for Bioscience and Biotechnology Research, NIST, Rockville, Maryland 20850 (United States); Chen, Lei, E-mail: lei.chen@nist.gov [NIST Center for Nanoscale Science and Technology, Gaithersburg, Maryland 20899-8313 (United States); Gawrisch, Klaus [Laboratory of Membrane Biochemistry and Biophysics, National Institute on Alcohol Abuse and Alcoholism, National Institutes of Health, Bethesda, Maryland 20892 (United States)

    2015-01-15

    Nanoporous platinum membranes can be straightforwardly fabricated by forming a Pt coating inside the nanopores of anodic alumina membranes (AAO) using atomic layer deposition (ALD). However, the high-aspect-ratio of AAO makes Pt ALD very challenging. By tuning the process deposition temperature and precursor exposure time, enhanced infiltration depth along with conformal coating was achieved for Pt ALD inside the AAO templates. Cross-sectional scanning electron microscopy/energy dispersive x-ray spectroscopy and small angle neutron scattering were employed to analyze the Pt coverage and thickness inside the AAO nanopores. Additionally, one application of platinum-coated membrane was demonstrated by creating a high-density protein-functionalized interface.

  12. Optical and magnetic properties of porous anodic alumina films embedded with Co nanowires

    Institute of Scientific and Technical Information of China (English)

    Zhang Jing-Jing; Li Zi-Yue; Zhang Hui-Min; Hou Xue; Sun Hui-Yuan

    2013-01-01

    A simple method to tune the optical properties of porous anodic alumina (PAA) films embedded with Co nanowires (PAA@Co nanocomposite films) is reported in this paper.The films exhibit vivid structural colors and magnetic properties.The optical properties of the films can be effectively tuned by adjusting the thickness of the PAA template.The deposition of Co nanowires greatly increases the color saturation of the PAA films.The theoretical results of the changes in structural color according to the Bragg-Snell formula are consistent with the experimental results.PAA@Co films can be used in many areas,including decoration,display,and multifunctional anti-counterfeiting applications.

  13. Fabrication and optical property of metal nanowire arrays embedded in anodic porous alumina membrane

    Science.gov (United States)

    Takase, Kouichi; Shimizu, Tomohiro; Sugawa, Kosuke; Aono, Takashige; Shirai, Yuma; Nishida, Tomohiko; Shingubara, Shoso

    2016-06-01

    Nanowires embedded in nanopores are potentially tough against surface scraping and agglomeration. In this study, we have fabricated Au and Ni nanowires embedded into anodic porous alumina (APA) and investigated their reflectance to study the effects of surface plasmon absorption properties and conversion from solar energy to thermal energy. Au nanowires embedded into APA show typical gold surface plasmon absorption at approximately 530 nm. On the other hand, Ni nanowires show quite a low reflectance under 600 nm. In the temperature elevation test, both Au and Ni nanowire samples present the same capability to warm up water. It means that Ni nanowires embedded into APA have almost the same photothermal activity as Au nanowires.

  14. Nanoporous Anodic Alumina 3D FDTD Modelling for a Broad Range of Inter-pore Distances

    Science.gov (United States)

    Bertó-Roselló, Francesc; Xifré-Pérez, Elisabet; Ferré-Borrull, Josep; Pallarès, Josep; Marsal, Lluis F.

    2016-08-01

    The capability of the finite difference time domain (FDTD) method for the numerical modelling of the optical properties of nanoporous anodic alumina (NAA) in a broad range of inter-pore distances is evaluated. FDTD permits taking into account in the same numerical framework all the structural features of NAA, such as the texturization of the interfaces or the incorporation of electrolyte anions in the aluminium oxide host. The evaluation is carried out by comparing reflectance measurements from two samples with two very different inter-pore distances with the simulation results. Results show that considering the texturization is crucial to obtain good agreement with the measurements. On the other hand, including the anionic layer in the model leads to a second-order contribution to the reflectance spectrum.

  15. Study the effect of striping in two-step anodizing process on pore arrangement of nano-porous alumina

    Energy Technology Data Exchange (ETDEWEB)

    Rahimi, M.H. [Department of Mining and Metallurgical Engineering, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of); Saramad, S., E-mail: ssaramad@aut.ac.ir [Department of Physics, Amirkabir University of Technology, Hafez Avenue, Tehran (Iran, Islamic Republic of); Tabaian, S.H.; Marashi, S.P. [Department of Mining and Metallurgical Engineering, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of); Zolfaghari, A. [Chemistry and Chemical Engineering Research Centre of Iran, Tehran (Iran, Islamic Republic of); Mohammadalinezhad, M. [Department of Mining and Metallurgical Engineering, Amirkabir University of Technology, Tehran (Iran, Islamic Republic of)

    2009-10-15

    Two-step anodic oxidation of aluminum is generally employed to produce the ordered porous anodized alumina (PAA). Dissolving away (striping) the oxide film after the first anodizing step plays a key role in the final arrangement of nano-pores. In this work, different striping durations between 1 and 6 h were applied to the sample that was initially anodized at a constant voltage of 40 V at 17 deg. C for 15 h. The striping duration of 3 h was realized as the optimum time for achieving the best ordering degree for the pores. Scanning electron microscopy (SEM) was used during and at the end of the process to examine the cross section and finishing surface of the specimens. Linear-angular fast Fourier transform (LA-FFT), an in-house technique based on MATLAB software, was employed to assess the ordering degree of the anodized samples.

  16. Structurally engineered anodic alumina nanotubes as nano-carriers for delivery of anticancer therapeutics.

    Science.gov (United States)

    Wang, Ye; Santos, Abel; Kaur, Gagandeep; Evdokiou, Andreas; Losic, Dusan

    2014-07-01

    Here, we report a study on the biocompatibility, cell uptake and in vitro delivery of tumor necrosis factor-related apoptosis-inducing ligand (Apo2L/TRAIL) by new nano-carriers called anodic alumina nanotubes (AANTs) for potential cancer therapy. AANTs were electrochemically engineered by a unique pulse anodization process, which enables precise control of the nanotube geometry, and used here as nano-carriers for drug delivery. In vitro cytotoxicity and cell uptake of AANTs was assessed using MDA-MB231-TXSA human breast cancer cells and mouse RAW 264.7 macrophage cells. AANTs exhibited excellent biocompatibility in both cell lines over a time course of five days even at a maximum concentration of AANTs of 100 μgmL(-1). Transmission electron microscopy and fluorescence microscopy confirmed a significant uptake of AANTs by RAW 264.7 cells and breast cancer cells. AANTs loaded with the pro-apoptotic protein Apo2L/TRAIL showed exceptional loading capacity (104 ± 14.4 μgmg(-1) of AANTs) and demonstrated significant decrease in viability of MDA-MB231-TXSA cancer cells due to apoptosis induction. These results demonstrate that AANTs are promising nano-carriers for drug delivery applications.

  17. Fabrication of Gold-Coated Ultra-Thin Anodic Porous Alumina Substrates for Augmented SERS

    Directory of Open Access Journals (Sweden)

    Chiara Toccafondi

    2016-05-01

    Full Text Available Anodic porous alumina (APA is a nanostructured material used as a template in several nanotechnological applications. We propose the use of APA in ultra-thin form (<100 nm for augmented surface-enhanced Raman scattering (SERS. Here, the effect of in-depth thinning of the APA nanostructures for possible maximization of SERS was addressed. Anodization was carried out on ultra-thin films of aluminum on glass and/or silicon, followed by pore-opening. Gold (Au was overcoated and micro‑Raman/SERS measurements were carried out on test target analytes. Finite integration technique simulations of the APA-Au substrate were used both for the experimental design and simulations. It was observed that, under optimized conditions of APA and Au thickness, the SERS enhancement is higher than on standard APA-Au substrates based on thin (~100 nm APA by up to a factor of ~20 for test molecules of mercaptobenzoic acid. The agreement between model and experimental results confirms the current understanding of SERS as being mainly due to the physical origin of plasmon resonances. The reported results represent one step towards micro-technological, integrated, disposable, high-sensitivity SERS chemical sensors and biosensors based on similar substrates.

  18. Sustained, Controlled and Stimuli-Responsive Drug Release Systems Based on Nanoporous Anodic Alumina with Layer-by-Layer Polyelectrolyte

    Science.gov (United States)

    Porta-i-Batalla, Maria; Eckstein, Chris; Xifré-Pérez, Elisabet; Formentín, Pilar; Ferré-Borrull, J.; Marsal, Lluis F.

    2016-08-01

    Controlled drug delivery systems are an encouraging solution to some drug disadvantages such as reduced solubility, deprived biodistribution, tissue damage, fast breakdown of the drug, cytotoxicity, or side effects. Self-ordered nanoporous anodic alumina is an auspicious material for drug delivery due to its biocompatibility, stability, and controllable pore geometry. Its use in drug delivery applications has been explored in several fields, including therapeutic devices for bone and dental tissue engineering, coronary stent implants, and carriers for transplanted cells. In this work, we have created and analyzed a stimuli-responsive drug delivery system based on layer-by-layer pH-responsive polyelectrolyte and nanoporous anodic alumina. The results demonstrate that it is possible to control the drug release using a polyelectrolyte multilayer coating that will act as a gate.

  19. Structure and Magnetic Properties of Ni Nanowires Array Fabricated by Direct Current Electro-deposition in Anodic Alumina Membrane

    Institute of Scientific and Technical Information of China (English)

    HUANG Xinmin; ZHU Hong; XU Jinxia

    2005-01-01

    Ordered nanostructure arrays of Ni-Al2O3 were synthesized by direct current electro-deposition in anodic alumina membranes (AAM). The investigation with an electron microscope,an X-ray diffractmeter and a vibration sample magnetometer indicates that the Ni nanowires, growing in the pores of AAM with about 45nm in diameter, are monocrystalline and have a definite preferred crystallizing orientation. The magnetic behavior of the arrays and their mechanism were discussed.

  20. On hydrophilicity improvement of the porous anodic alumina film by hybrid nano/micro structuring

    Science.gov (United States)

    Wang, Weichao; Zhao, Wei; Wang, Kaige; Wang, Lei; Wang, Xuewen; Wang, Shuang; Zhang, Chen; Bai, Jintao

    2017-09-01

    In both, laboratory and industry, tremendous attention is paid to discover an effective technique to produce uniform, controllable and (super) hydrophilic surfaces over large areas that are useful in a wide range of applications. In this investigation, by combing porous anodic alumina (PAA) film with nano-structures and microarray of aluminum, the hydrophilicity of hybrid nano-micro structure has been significantly improved. It is found some factors can affect the hydrophilicity of film, such as the size and aspect ratio of microarray, the thickness of nano-PAA film etc. Comparing with pure nano-PAA films and microarray, the hybrid nano-micro structure can provide uniform surface with significantly better hydrophilicity. The improvement can be up to 84%. Also, this technique exhibits good stability and repeatability for industrial production. By optimizing the thickness of nano-PAA film and aspect ratio of micro-structures, super-hydrophilicity can be reached. This study has obvious prospect in the fields of chemical industry, biomedical engineering and lab-on-a-chip applications.

  1. Realisation and optical engineering of linear variable bandpass filters in nanoporous anodic alumina photonic crystals.

    Science.gov (United States)

    Sukarno; Law, Cheryl Suwen; Santos, Abel

    2017-06-08

    We present the first realisation of linear variable bandpass filters in nanoporous anodic alumina (NAA-LVBPFs) photonic crystal structures. NAA gradient-index filters (NAA-GIFs) are produced by sinusoidal pulse anodisation and used as photonic crystal platforms to generate NAA-LVBPFs. The anodisation period of NAA-GIFs is modified from 650 to 850 s to systematically tune the characteristic photonic stopband of these photonic crystals across the UV-visible-NIR spectrum. Then, the nanoporous structure of NAA-GIFs is gradually widened along the surface under controlled conditions by wet chemical etching using a dip coating approach aiming to create NAA-LVBPFs with finely engineered optical properties. We demonstrate that the characteristic photonic stopband and the iridescent interferometric colour displayed by these photonic crystals can be tuned with precision across the surface of NAA-LVBPFs by adjusting the fabrication and etching conditions. Here, we envisage for the first time the combination of the anodisation period and etching conditions as a cost-competitive, facile, and versatile nanofabrication approach that enables the generation of a broad range of unique LVBPFs covering the spectral regions. These photonic crystal structures open new opportunities for multiple applications, including adaptive optics, hyperspectral imaging, fluorescence diagnostics, spectroscopy, and sensing.

  2. Photo Induced Membrane Separation for Water Purification and Desalination Using Azobenzene Modified Anodized Alumina Membranes.

    Science.gov (United States)

    Fujiwara, Masahiro; Imura, Tatsuki

    2015-06-23

    Water purification and desalination to produce end-use water are important agendas in 21st century, because the global water shortage is becoming increasingly serious. Those processes using light energy, especially solar energy, without the consumption of fossil fuels are desired for creating sustainable society. For these earth-friendly water treatments, nanoporous materials and membranes are expected to provide new technologies. We have reported before that the repetitive photo isomerization of azobenzene groups between the trans and cis isomers induced by the simultaneous irradiation of UV and visible lights accelerates the molecular movement of nearby molecules in nanoporous materials. After further studies, we recently found that the permeation of water through azobenzene modified anodized alumina membranes as a photo responsive nanoporous membrane was achieved by the simultaneous irradiation of UV and visible lights, while no water penetration occurred under no light, only single UV or visible light. The photo induced permeation of water was promoted by the vaporization of water with the repetitive photo isomerization of azobenzene. This membrane permeation achieved the purification of water solutions, because dye molecules and a protein dissolved in aqueous solutions were not involved in the photo induced penetrated water. When 3.5% of sodium chloride solution as model seawater was employed for this membrane separation, the salt content of the permeated water was less than 0.01% to accomplish the complete desalination of seawater.

  3. Electrochemical synthesis of CdS nanowires by underpotential deposition in anodic alumina membrane templates

    Energy Technology Data Exchange (ETDEWEB)

    Bicer, Mustafa; Aydin, Ali Osman [Department of Chemistry, Arts and Sciences Faculty, Sakarya University, 54187 Sakarya (Turkey); Sisman, Ilkay, E-mail: isisman@sakarya.edu.t [Department of Chemistry, Arts and Sciences Faculty, Sakarya University, 54187 Sakarya (Turkey)

    2010-04-15

    Cadmium sulfide (CdS) nanowires were electrosynthesized within the pores of the anodic alumina membranes (AAM) using underpotential deposition (UPD) through an electrochemical co-deposition at room temperature (25 deg. C). The nanowire arrays were grown from an aqueous solution of CdSO{sub 4}, ethylenediaminetetraacetic acid (EDTA), and Na{sub 2}S at pH 4.0. X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), UV-vis absorption spectroscopy, and energy dispersive spectroscopy (EDS) were employed to characterize the nanowires. These nanowires have uniform diameters of approximately 90 nm, and their lengths are up to 7 mum. XRD analysis reveals that the electrosynthesized nanowires deposited at -500 mV (vs. Ag/AgCl) have a preferential orientation along (1 1 0) direction for hexagonal crystal. Electrochemical and EDS results of the deposits confirm that the atomic ratio of Cd to S is very close to 1:1 stoichiometry. UV-vis absorption measurement shows a blue-shifted absorption at 488 nm because of the quantum confinement at low dimensions.

  4. Structure of the carbon nanofilaments formed by liquid phase carbonization in porous anodic alumina template

    Energy Technology Data Exchange (ETDEWEB)

    Habazaki, H. [Graduate School of Engineering, Hokkaido University, N13-W8, Sapporo 060-8628 (Japan)], E-mail: habazaki@eng.hokudai.ac.jp; Kiriu, M.; Hayashi, M.; Konno, H. [Graduate School of Engineering, Hokkaido University, N13-W8, Sapporo 060-8628 (Japan)

    2007-10-15

    Platelet structure carbon nanofilaments of {approx}30 nm in diameter have been prepared by heating a mixture of porous anodic alumina template and poly(vinyl)chloride (PVC) powders in an argon atmosphere, and the change in their structure and morphology with heat treatment temperature, ranging from 600 to 2800 deg. C, has been examined using X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and nitrogen gas adsorption measurements. The diameter of the carbon nanofilaments formed does not change with heat treatment temperature, being in agreement with the pore diameter of the template, while their length is reduced with the temperature. The platelet-type orientation of graphene layers is evident even at 600 deg. C with the layer structure further developing with increasing heat treatment temperature. The carbon nanofilaments formed at lower temperatures have micropores, while those formed at higher temperatures do not have porosity. Highly graphitized carbon nanofilaments have been obtained after heat treatment at 2800 deg. C, with another characteristic structural feature being presence of loops at the edge of graphene layers formed at 2800 deg. C.

  5. Effect of Anodic Alumina Oxide Pore Diameter on the Crystallization of Poly(butylene adipate).

    Science.gov (United States)

    Sun, Xiaoli; Fang, Qunqun; Li, Huihui; Ren, Zhongjie; Yan, Shouke

    2016-04-05

    Poly(butylene adipate) (PBA) was infiltrated into the anodic alumina oxide (AAO) templates with the pore diameter of around 30, 70, and 100 nm and PBA nanotubes with different diameters were prepared. The crystallization and phase transition behavior of the obtained PBA nanotubes capped in the nanopores have been explored by using X-ray diffraction and differential scanning calorimetry. Only α-PBA crystals form in the bulk sample during nonisothermal crystallization. By contrast, predominant β-PBA crystals form in the AAO templates. The β-PBA crystals formed in the nanopores with pore diameter less than 70 nm prefer to adopt an orientation with their b-axis parallel to the long axis of the pore. During the melt recrystallization, it was found that the critical temperature (Tβ), below which pure β-crystals form, is 20 °C for bulk PBA. It drops down significantly with the pore diameter for the PBA in the AAO template. Moreover, the β-crystals in the porous template exhibit larger lattice parameters compared with the bulk crystals. By monitoring the change of β-crystals in the heating process, it was found that β-crystals in the AAO template with the pore diameter of 30 nm (D30) melt directly while the β-crystals transform to α-crystals in the template with the pore diameter of 100 nm (D100). The intensity of (020) Bragg peak of β-crystals decreases at a similar rate in both D30 and D100 but disappears at a relatively lower temperature in D30. On the other hand, the β(110) peak intensity of β-PBA crystals formed in the D100 template decreases first at slower rate before α crystals appear, and then at a faster rate once the β to α phase transition takes place.

  6. Preparation of mesoporous alumina films by anodization: Effect of pretreatments on the aluminum surface and MTBE catalytic oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Vazquez, A.L., E-mail: avazquezd@ipn.m [Departamento de Ingenieria Metalurgica, ESIQIE-IPN, AP 75-876, Mexico, D.F. (Mexico); Programa de Ingenieria Molecular, Instituto Mexicano del Petroleo, Eje Lazaro Cardenas 152, C.P. 07730, Mexico, D.F. (Mexico); Carrera, R. [Departamento de Ingenieria Metalurgica, ESIQIE-IPN, AP 75-876, Mexico, D.F. (Mexico); Programa de Ingenieria Molecular, Instituto Mexicano del Petroleo, Eje Lazaro Cardenas 152, C.P. 07730, Mexico, D.F. (Mexico); Arce, E. [Departamento de Ingenieria Metalurgica, ESIQIE-IPN, AP 75-876, Mexico, D.F. (Mexico); Castillo, N. [CINVESTAV, Departamento de Fisica. Av. IPN 2508, 07360, Mexico, D.F (Mexico); Castillo, S. [Departamento de Ingenieria Metalurgica, ESIQIE-IPN, AP 75-876, Mexico, D.F. (Mexico); Programa de Ingenieria Molecular, Instituto Mexicano del Petroleo, Eje Lazaro Cardenas 152, C.P. 07730, Mexico, D.F. (Mexico); Moran-Pineda, M. [Programa de Ingenieria Molecular, Instituto Mexicano del Petroleo, Eje Lazaro Cardenas 152, C.P. 07730, Mexico, D.F. (Mexico)

    2009-08-26

    Mesoporous materials are both scientifically and technologically important because of the presence of voids of controllable dimensions at atomic, molecular, and nanometric scales. Over the last decade, there has been both an increasing interest and research effort in the synthesis and characterization of these types of materials. The purposes of this work are to study the physical and chemical changes in the properties of mesoporous alumina films produced by anodization in sulphuric acid by different pretreatments on the aluminium surface such as mechanical polishing [MP] and electropolishing [EP]; and to compare their properties such as morphology, structure and catalytic activity with those present in commercial alumina. The morphologic and physical characterizations of the alumina film samples were carried out by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The chemical evaluations were performed by the oxidation of methyl-tert-butyl-ether (MTBE) at 400 deg. C under O{sub 2}/He oxidizing conditions (Praxair, 2.0% O{sub 2}/He balance). According to the results, the samples that presented higher activities than those in Al{sub 2}O{sub 3}/Al [MP] and commercial alumina in the MTBE oxidation (69%), were those prepared by Al{sub 2}O{sub 3}/Al [EP]. The average mesoporous diameter was 17 nm, and the morphological shape was equiaxial; thus, that pore distribution was the smallest of all with a homogeneous distribution.

  7. Fabrication of Acrylonitrile-Butadiene-Styrene Nanostructures with Anodic Alumina Oxide Templates, Characterization and Biofilm Development Test for Staphylococcus epidermidis.

    Directory of Open Access Journals (Sweden)

    Camille Desrousseaux

    Full Text Available Medical devices can be contaminated by microbial biofilm which causes nosocomial infections. One of the strategies for the prevention of such microbial adhesion is to modify the biomaterials by creating micro or nanofeatures on their surface. This study aimed (1 to nanostructure acrylonitrile-butadiene-styrene (ABS, a polymer composing connectors in perfusion devices, using Anodic Alumina Oxide templates, and to control the reproducibility of this process; (2 to characterize the physico-chemical properties of the nanostructured surfaces such as wettability using captive-bubble contact angle measurement technique; (3 to test the impact of nanostructures on Staphylococcus epidermidis biofilm development. Fabrication of Anodic Alumina Oxide molds was realized by double anodization in oxalic acid. This process was reproducible. The obtained molds present hexagonally arranged 50 nm diameter pores, with a 100 nm interpore distance and a length of 100 nm. Acrylonitrile-butadiene-styrene nanostructures were successfully prepared using a polymer solution and two melt wetting methods. For all methods, the nanopicots were obtained but inside each sample their length was different. One method was selected essentially for industrial purposes and for better reproducibility results. The flat ABS surface presents a slightly hydrophilic character, which remains roughly unchanged after nanostructuration, the increasing apparent wettability observed in that case being explained by roughness effects. Also, the nanostructuration of the polymer surface does not induce any significant effect on Staphylococcus epidermidis adhesion.

  8. Comparative study of formation and corrosion performance of porous alumina and ceramic nanorods formed in different electrolytes by anodization

    Energy Technology Data Exchange (ETDEWEB)

    Raj, V., E-mail: alaguraj2@rediffmail.com; Mumjitha, M., E-mail: mumjitha@gmail.com

    2014-01-15

    Highlights: • Alumina–titania coatings were fabricated by anodization in a single step. • The universal and cheap sulphuric acid was used as the reference electrolyte. • The minimum concentration of PTO is used to achieve ceramic nanorods. • Dense ceramic coatings were achieved at low current density and room temperature. • Anodized coatings show better corrosion resistance compared to bare aluminium. -- Abstract: Fabrication of Al{sub 2}O{sub 3}–TiO{sub 2} nanoceramic coatings on aluminium was carried out in a single step using cost effective sulphuric acid electrolyte with the addition of potassium titanium oxalate (PTO) by anodization method. For comparison, the anodization was also carried out in sulphuric acid electrolyte alone. The effect of composition of the electrolyte, current density and electrolyte concentration on formation and surface characteristics of anodic alumina and ceramic coatings produced from different electrolytes have been investigated. The growth process, surface morphology, nanostructure, distribution of chemical elements, phase constitutions and corrosion resistance of the coatings formed in two different electrolytes were investigated by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), Tafel polarization technique and electrochemical impedance spectroscopy (EIS). As the concentration of electrolyte and current density increased, the surface properties of the coating increased up to certain content and beyond that they decreased. Dense, uniform nanoceramic coatings with less surface defects were obtained from sulphuric acid + PTO electrolyte. The corrosion studies reveal that ceramic coating formed in sulphuric acid + PTO electrolyte offers better corrosion resistance compared to the alumina coating formed in sulphuric acid electrolyte.

  9. Facile Fabrication of Anodic Alumina Rod-Capped Nanopore Films with Condensate Microdrop Self-Propelling Function.

    Science.gov (United States)

    Li, Juan; Zhang, Wenjing; Luo, Yuting; Zhu, Jie; Gao, Xuefeng

    2015-08-26

    We report that aluminum surfaces can be endowed with condensate microdrop self-propelling (CMDSP) function by one-step voltage-rising mild anodization in hot phosphoric acid solution followed by fluorosilane modification. Via regulating reaction parameters, we can achieve anodic alumina self-standing rod-capped nanopore films and minimize their solid-liquid interface adhesion. Such low-adhesive nanostructured film owns remarkable CMDSP function, especially to condensate microdrops with sizes below 50 μm, differing from usual gravity-driven dropwise condensation on flat aluminum surfaces. Clearly, this work offers a facile, efficient, and industry-compatible approach to processing CMDSP aluminum materials, which is significant for developing innovative energy-saving air-conditioner heat exchangers.

  10. A Novel Method for Fabricating Double Layers Porous Anodic Alumina in Phosphoric/Oxalic Acid Solution and Oxalic Acid Solution

    Directory of Open Access Journals (Sweden)

    Yanfang Xu

    2016-01-01

    Full Text Available A novel method for fabricating ordered double layers porous anodic alumina (DL-PAA with controllable nanopore size was presented. Highly ordered large pore layer with interpore distance of 480 nm was fabricated in phosphoric acid solution with oxalic acid addition at the potential of 195 V and the small pore layer was fabricated in oxalic acid solution at the potential from 60 to 100 V. Experimental results show that the thickness of large pore layer is linearly correlative with anodizing time, and pore diameter is linearly correlative with pore widening time. When the anodizing potential in oxalic acid solution was adjusted from 60 to 100 V, the small pore layers with continuously tunable interpore distance from 142 to 241 nm and pore density from 1.94×109 to 4.89×109 cm−2 were obtained. And the interpore distance and the pore density of small pore layers are closely correlative with the anodizing potential. The fabricated DL-PAA templates can be widely utilized for fabrication of ordered nanomaterials, such as superhydrophobic or gecko-inspired adhesive materials and metal or semiconductor nanowires.

  11. Corrosion of cermet anodes during low temperature electrolysis of alumina. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Kozarek, R.L.; Ray, S.P.; Dawless, R.K.; LaCamera, A.F.

    1997-09-26

    Successful development of inert anodes to replace carbon anodes in Hall cells has the potential benefits of lower energy consumption,lower operating costs, and reduced CO{sub 2} and CO emissions. Using inert anodes at reduced current density and reduced operating temperature (800 C) has potential for decreasing the corrosion rate of inert anodes. It may also permit the use of new materials for containment and insulation. This report describes the fabrication characteristics and the corrosion performance of 5324-17% Cu Cermet anodes in 100 hour tests. Although some good results were achieved, the corrosion rate at low temperature (800 C) is varied and not significantly lower than typical results at high temperature ({approximately} 960 C). This report also describes several attempts at 200 hour tests, with one anode achieving 177 hours of continuous operation and another achieving a total of 235 hours but requiring three separate tests of the same anode. The longest run did show a lower wear rate in the last test; but a high resistance layer developed on the anode surface and forced an unacceptably low current density. It is recommended that intermediate temperatures be explored as a more optimal environment for inert anodes. Other electrolyte chemistries and anode compositions (especially high conductivity anodes) should be considered to alleviate problems associated with lower temperature operation.

  12. Spectroscopic and nonlinear photophysical characterization of organic octupolar-compounds supported by anodic-alumina nanotube-arrays

    Energy Technology Data Exchange (ETDEWEB)

    Morales-Saavedra, O.G., E-mail: omar.morales@ccadet.unam.mx [Lab. of Nonlinear Optics, Centro de Ciencias Aplicadas y Desarrollo Tecnologico, Universidad Nacional Autonoma de Mexico, CCADET-UNAM Cd. Universitaria, Coyoacan, A.P. 70-186, C.P. 04510 Mexico City (Mexico); Ontiveros-Barrera, F.G. [Lab. of Nonlinear Optics, Centro de Ciencias Aplicadas y Desarrollo Tecnologico, Universidad Nacional Autonoma de Mexico, CCADET-UNAM Cd. Universitaria, Coyoacan, A.P. 70-186, C.P. 04510 Mexico City (Mexico); Hennrich, G. [Departamento de Quimica Organica, Universidad Autonoma de Madrid, Cantoblanco, 28049 Madrid (Spain); Mata-Zamora, M.E.; Rodriguez-Rosales, A.A.; Banuelos, J.G. [Lab. of Nonlinear Optics, Centro de Ciencias Aplicadas y Desarrollo Tecnologico, Universidad Nacional Autonoma de Mexico, CCADET-UNAM Cd. Universitaria, Coyoacan, A.P. 70-186, C.P. 04510 Mexico City (Mexico)

    2011-11-15

    Highlights: > Preparation of organic-inorganic nanostructured hybrid materials. > Insertion of octupolar compounds in alumina nanotube arrays. > Linear and nonlinear photophysical characterization of solid-state hybrid structures. > Fabrication of photonic materials. - Abstract: Amorphous anodic alumina membranes (AAM) comprising highly ordered nanometric porous arrays (porous anodic aluminas: PAA) with 1D-nanotube dimensions of {approx}75 nm in diameter and 45 microns in depth were successfully prepared and used as nanostructured host networks for different functionalized octupolar chromophores (named here Oct-(n)). Atomic force microscopy (AFM) studies performed on the developed hybrid systems confirmed a homogeneous insertion of these organic molecules into the PAA nanotube-arrays. Samples with high structural quality were selected for several photophysical characterizations: Comprehensive X-ray diffraction (XRD) and optical spectroscopic characterizations performed according to UV-vis absorption, photoluminescent (PL) and Raman measurements revealed the structural and optical performance of these molecules within the PAA-confinement. Since the implemented optical chromophores were specifically functionalized for nonlinear optical (NLO) applications, the obtained Oct-(n)/PAA-based amorphous hybrids were also characterized according to cubic NLO-techniques such as third harmonic generation (THG) and the Z-Scan method. PAA-confined octupolar chromophores have shown interesting linear and NLO optical properties which have not yet been intensively investigated in bulk hybrid systems; hence, the obtained hybrid nanostructures represent a promising field of investigation in the route to functional octupolar-based materials, where different self-assembled molecular structures may be formed, giving rise to enhanced linear and NLO-properties.

  13. Nanoporous alumina formed by self-organized two-step anodization of Ni{sub 3}Al intermetallic alloy in citric acid

    Energy Technology Data Exchange (ETDEWEB)

    Stepniowski, Wojciech J., E-mail: wstepniowski@wat.edu.pl [Department of Advanced Materials and Technology, Faculty of New Technologies and Chemistry, Military University of Technology, Kaliskiego 2 Str., 00-908 Warszawa (Poland); Cieslak, Grzegorz; Norek, Malgorzata; Karczewski, Krzysztof; Michalska-Domanska, Marta; Zasada, Dariusz; Polkowski, Wojciech; Jozwik, Pawel; Bojar, Zbigniew [Department of Advanced Materials and Technology, Faculty of New Technologies and Chemistry, Military University of Technology, Kaliskiego 2 Str., 00-908 Warszawa (Poland)

    2013-01-01

    Highlights: Black-Right-Pointing-Pointer Anodic porous alumina was formed by Ni{sub 3}Al intermetallic alloy anodization. Black-Right-Pointing-Pointer The anodizations were conducted in 0.3 M citric acid. Black-Right-Pointing-Pointer Nanopores geometry depends on anodizing voltage. Black-Right-Pointing-Pointer No barrier layer was formed during anodization. - Abstract: Formation of the nanoporous alumina on the surface of Ni{sub 3}Al intermetallic alloy has been studied in details and compared with anodization of aluminum. Successful self-organized anodization of this alloy was performed in 0.3 M citric acid at voltages ranging from 2.0 to 12.0 V using a typical two-electrode cell. Current density records revealed different mechanism of the porous oxide growth when compared to the mechanism pertinent for the anodization of aluminum. Electrochemical impedance spectroscopy experiments confirmed the differences in anodic oxide growth. Surface and cross-sections of the Ni{sub 3}Al intermetallic alloy with anodic oxide were observed with field-emission scanning electron microscope and characterized with appropriate software. Nanoporous oxide growth rate was estimated from cross-sectional FE-SEM images. The lowest growth rate of 0.14 {mu}m/h was found for the anodization at 0 Degree-Sign C and 2.0 V. The highest one - 2.29 {mu}m/h - was noticed for 10.0 V and 30 Degree-Sign C. Pore diameter was ranging from 18.9 nm (2.0 V, 0 Degree-Sign C) to 32.0 nm (12.0 V, 0 Degree-Sign C). Interpore distance of the nanoporous alumina was ranging from 56.6 nm (2.0 V, 0 Degree-Sign C) to 177.9 nm (12.0 V, 30 Degree-Sign C). Pore density (number of pore occupying given area) was decreasing with anodizing voltage increase from 394.5 pores/{mu}m{sup 2} (2.0 V, 0 Degree-Sign C) to 94.9 pores/{mu}m{sup 2} (12.0 V, 0 Degree-Sign C). All the geometrical features of the anodic alumina formed by two-step self-organized anodization of Ni{sub 3}Al intermetallic alloy are depending on the

  14. Porous Alumina Films with Width-Controllable Alumina Stripes

    Directory of Open Access Journals (Sweden)

    Huang Shi-Ming

    2010-01-01

    Full Text Available Abstract Porous alumina films had been fabricated by anodizing from aluminum films after an electropolishing procedure. Alumina stripes without pores can be distinguished on the surface of the porous alumina films. The width of the alumina stripes increases proportionally with the anodizing voltage. And the pores tend to be initiated close to the alumina stripes. These phenomena can be ascribed to the electric field distribution in the alumina barrier layer caused by the geometric structure of the aluminum surface.

  15. Porous Alumina Films with Width-Controllable Alumina Stripes.

    Science.gov (United States)

    Huang, Kai; Huang, Shi-Ming; Pu, Lin; Shi, Yi; Wu, Zhi-Ming; Ji, Li; Kang, Jun-Yong

    2010-08-21

    Porous alumina films had been fabricated by anodizing from aluminum films after an electropolishing procedure. Alumina stripes without pores can be distinguished on the surface of the porous alumina films. The width of the alumina stripes increases proportionally with the anodizing voltage. And the pores tend to be initiated close to the alumina stripes. These phenomena can be ascribed to the electric field distribution in the alumina barrier layer caused by the geometric structure of the aluminum surface.

  16. Structured Ni catalysts on porous anodic alumina membranes for methane dry reforming: NiAl 2 O 4 formation and characterization

    KAUST Repository

    Zhou, Lu

    2015-06-29

    This communication presents the successful design of a structured catalyst based on porous anodic alumina membranes for methane dry reforming. The catalyst with a strong Ni-NiAl2O4 interaction shows both excellent activity and stability. This journal is © The Royal Society of Chemistry.

  17. Guided transmission of slow Ne ions through the nanochannels of highly ordered anodic alumina

    DEFF Research Database (Denmark)

    Mátéfi-Tempfli, Stefan; Mátéfi-Tempfli, M.; Piraux, L.;

    2006-01-01

    A highly ordered hexagonally close-packed nanochannels array was prepared using the self-ordering phenomena during a two-step anodization process of a high purity aluminium foil. The anodized aluminium oxide, with pore diameters of about 280nm and interpore distances of about 450nm was prepared...

  18. Electrochemical behaviors of anodic alumina sealed by Ce-Mo in NaCl solutions

    Institute of Scientific and Technical Information of China (English)

    TIAN Lian-peng; ZHAO Xu-hui; ZHAO Jing-mao; ZHANG Xiao-feng; ZUO Yu

    2006-01-01

    The elimination of toxic materials in sealing methods for anodic films on 1070 aluminum alloy was studied. The new process uses chemical treatments in cerium solution and an electrochemical treatment in a molybdate solution. Potentiodynamic polarization and electrochemical impedance spectroscopy(EIS) were used to study the influences of sealing methods on the corrosion behavior of anodic films in NaCl solutions. The results show that the Ce-Mo sealing makes the surface structure and morphology of anodic films uniform and compact. Ce and Mo produce a cooperative effect to improve the corrosion resistance of anodic films. Anodic films sealed by Ce-Mo provide high corrosion resistance both in acidic and basic solutions.

  19. HfO2/porous anodic alumina composite films for multifunctional data storage media materials under electric field control

    Science.gov (United States)

    Qi, Li-Qian; Pan, Di-Ya; Li, Jun-Qing; Liu, Li-Hu; Sun, Hui-Yuan

    2017-03-01

    New materials for achieving direct electric field control of ferromagnetism and resistance behavior are highly desirable in the development of multifunctional data storage devices. In this paper, HfO2 nanoporous films have been fabricated on porous anodic alumina (PAA) substrates by DC-reactive magnetron sputtering. Electrically induced resistive switching (RS) and modulated room temperature ferromagnetism are simultaneously found in a Ag/HfO2/PAA/Al (Ag/HP/Al) heterostructure. The switching mechanism between low resistance state and high resistance state is generally attributed to the formation/rupture of conductive filaments which may consist of oxygen vacancies. The combination of the electric field control of magnetization change and RS makes HP films possible for the multifunctional data storage media materials.

  20. Numerical and Experimental Study of the Structural Color by Widening the Pore Size of Nanoporous Anodic Alumina

    Directory of Open Access Journals (Sweden)

    Jiawen Li

    2014-01-01

    Full Text Available The structural color originated from the nanoporous anodic alumina (NAA film is related to the structural characteristics. This paper aimed to obtain different structural colors which can cover the whole visible range by widening the pore size of metal-coated NAA. First, we used the Finite Difference Time Domain (FDTD method to analyze the relationship between the physical structure and optical properties. Then, we fabricated different colors and expected color pattern by widening the pore diameter of NAA. Numerical and experimental study shows that the colors can cover the whole visible range by widening the pore diameter. This work can not only lead to better understanding of the mechanism of tuning color on NAA film, but also help us to fabricate expected color in the whole light range.

  1. The simulation of the temperature effects on the microhardness of anodic alumina oxide layers

    Directory of Open Access Journals (Sweden)

    M. Gombár

    2014-01-01

    Full Text Available In order to improve the mechanical properties of the layer deposited by anodic oxidation of aluminum on the material EN AW-1050 H24, in the contribution was investigated the microhardness of the deposited layer as a function of the physic-chemical factors affecting in the process of anodic oxidation at the constant anodic current density J = 3 A.dm-2 in electrolyte formed by sulfuric acid and oxalic acid, with the emphasis on the influence of electrolyte temperature in the range – 1,78 °C to 45,78 °C. The model of the studied dependence was compiled based on mathematical and statistical analysis of matrix from experimental obtained data from composite rotation plan of experiment with five independent variable factors (amount of sulfuric acid in the electrolyte, the amount of oxalic acid in the electrolyte, electrolyte, anodizing time and applied voltage.

  2. Self-Ordered Nanoporous Alumina Templates Formed by Anodization of Aluminum in Oxalic Acid

    Science.gov (United States)

    Vida-Simiti, Ioan; Nemes, Dorel; Jumate, Nicolaie; Thalmaier, Gyorgy; Sechel, Niculina

    2012-10-01

    Anodic aluminum oxide (AAO) membranes with highly ordered nanopores serve as ideal templates for the formation of various nanostructured materials. The procedure of the template preparation is based on a two-step self-organized anodization of aluminum. In the current study, AAO templates were fabricated in 0.3 M oxalic acid under the anodizing potential range of 30-60 V at an electrolyte temperature of ~5°C. The AAO templates were analyzed using scanning electron microscopy, x-ray diffraction, Fourier-transform infrared spectroscopy, and differential thermal analysis. The as obtained layers are amorphous; the mean pore size is between 40 nm and 75 nm and increases with the increase of the anodization potential. Well-defined pores across the whole aluminum template, a pore density of ~1010 pores/cm2, and a tendency to form a porous structure with hexagonal symmetry were observed.

  3. Heteroepitaxy of Ge on Si(001) with pits and windows transferred from free-standing porous alumina mask

    Science.gov (United States)

    Huangfu, Yourui; Zhan, Wenbo; Hong, Xia; Fang, Xu; Ding, Guqiao; Ye, Hui

    2013-05-01

    This paper reports the use of ultrathin free-standing porous alumina membrane (PAM) in pattern transferring for selective epitaxial growth (SEG) of Ge dots and films on Si. PAM, as a large-scale, controllable and lithography-free mask, can transfer nanopatterns onto Si without introducing any contaminants. High-density Ge dots are achievable with Ge adatoms confined in Si pits transferred from PAM. High-quality Ge films can also be grown on Si substrates through SiO2 nano-windows. In this work, 80 and 60 nm pore sizes of PAM were transferred to 70, 50 and 20 nm windows for comparison. For the former two sizes, over-etching of Si beneath every SiO2 window forms epi-seeds to improve intermixing of Ge-Si. No threading dislocations can be observed emanating from the epi-seeds due to the decreased lattice mismatch. An innovative shadow-etching technique utilizing the aspect ratio of PAM further decreased the lateral dimension of patterns from 60 to 20 nm. Cross-sectional transmission electron microscopy images show that the selective epitaxial Ge films grown from a 20 nm-width interface are defect free, which is attributed to the exponential decay of strain energy as well as Ge-Si intermixing.

  4. The effect of different oxide layers on the sensing properties of anodic alumina nanoporous film

    Directory of Open Access Journals (Sweden)

    H. Abbasian

    2014-03-01

    Full Text Available In the present work, anodized aluminum oxide template was prepared by accelerated mild anodization technique in 0.6M phosphoric aside and 175 V, anodization voltage. Pore widening was performed by chemical etching in 0.5M phosphoric acid for 8, 16, 32, 40 minutes. Scanning Electron Microscopy (SEM images showed the pores, diameter exponentially increases with etching time. By depositing silver contacts on the prepared samples and using an RC circuit for applying impedance spectroscopy, the characteristics of the humidity sensor based on constructed samples were investigated. The maximum response was seen for the sample etched for 40 minutes. For this sample, the detectable threshold of relative moisture was 30% and the response and the recovery time were 8, 2 seconds, respectively

  5. MEASUREMENT OF ANODIC OVERVOLTAGE BY A MODIFIED CURRENT INTERRUPTION METHOD IN CRYOLITE-ALUMINA MELTS

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    Generally, there are reasons to believe that the experimental technique has been inadequate in some works on anodic overvoltage measurements in aluminium electrolysis, therefore, the overvoltage data are not quite correct. Several causes affecting the precision of measurements were analyzed, a cell configuration ( vertical carbon anodes, insulated bottom and inner wall of graphite crucible as cathode) was used for overvoltage studies. An improved current interruption technique was used with current interrupted in less than 2μs and a simulation was applied to the oscillating potential decay curve.

  6. Fabrication of optical chemical ammonia sensors using anodized alumina supports and sol-gel method.

    Science.gov (United States)

    Markovics, Akos; Kovács, Barna

    2013-05-15

    In this comparative study, the fabrication and the sensing properties of various reflectometric optical ammonia gas sensors are described. In the first set of experiments the role of the support material was investigated on four different sensor membranes. Two of them were prepared by the adsorption of bromocresol green indicator on anodized aluminum plates. The applied anodizing voltages were 12 V and 24 V, which resulted in different dynamic ranges and response times for gaseous ammonia. The sol-gel method was used for the preparation of the other batch of sensors. These layers were coated on anodized aluminum plates (24 V) and on standard microscope cover glasses. In spite of the identical sensing chemistry, slightly different response times were measured merely because of the aluminum surface porosity. Gas molecules can remain entrapped in the pores, which results in delayed recovery time. On the other hand, the porous oxide film provides excellent adhesion, making the anodized aluminum an attractive support for the sol-gel layer.

  7. Influence of patterned concave depth and surface curvature on anodization of titania nanotubes and alumina nanopores.

    Science.gov (United States)

    Chen, Bo; Lu, Kathy

    2011-10-04

    Vertically aligned TiO(2) nanotube and Al(2)O(3) nanopore arrays have been obtained by pattern guided anodization with uniform concave depths. There are some studies about the effect of surface curvature on the growth of Al(2)O(3) nanopores. However, the surface curvature influence on the development of TiO(2) nanotubes is seldom studied. Moreover, there is no research about the effect of heterogeneous concave depths of the guiding patterns on the anodized TiO(2) nanotube and Al(2)O(3) nanopore characteristics, such as diameter, growth direction, and termination/bifurcation. In this study, focused ion beam lithography is used to create concave patterns with heterogeneous depths on flat surfaces and with uniform depths on curved surfaces. For the former, bending and bifurcation of nanotubes/nanopores are observed after the anodization. For the latter, bifurcation of a large tube into two smaller tubes occurs on concave surfaces, while termination of existing tubes occurs on convex surfaces. The growth direction of all TiO(2) nanotubes is perpendicular to the local surface and thus is different on different facets of the same Ti foil. At the edge of the Ti foil where two facets meet, the nanotube growth direction is bent, resulting in a large stress release that causes the formation of cracks. © 2011 American Chemical Society

  8. Surface-enhanced Raman scattering of self-assembled thiol monolayers and supported lipid membranes on thin anodic porous alumina

    Science.gov (United States)

    Shayganpour, Amirreza; Salis, Barbara; Dante, Silvia

    2017-01-01

    Thin anodic porous alumina (tAPA) was fabricated from a 500 nm thick aluminum (Al) layer coated on silicon wafers, through single-step anodization performed in a Teflon electrochemical cell in 0.4 M aqueous phosphoric acid at 110 V. Post-fabrication etching in the same acid allowed obtaining tAPA surfaces with ≈160 nm pore diameter and ≈80 nm corresponding wall thickness to be prepared. The tAPA surfaces were made SERS-active by coating with a thin (≈25 nm) gold (Au) layer. The as obtained tAPA–Au substrates were incubated first with different thiols, namely mercaptobenzoic acid (MbA) and aminothiol (AT), and then with phospholipid vesicles of different composition to form a supported lipid bilayer (SLB). At each step, the SERS substrate functionality was assessed, demonstrating acceptable enhancement (≥100×). The chemisorption of thiols during the first step and the formation of SLB from the vesicles during the second step, were independently monitored by using a quartz crystal microbalance with dissipation monitoring (QCM-D) technique. The SLB membranes represent a simplified model system of the living cells membranes, which makes the successful observation of SERS on these films promising in view of the use of tAPA–Au substrates as a platform for the development of surface-enhanced Raman spectroscopy (SERS) biosensors on living cells. In the future, these tAPA–Au-SLB substrates will be investigated also for drug delivery of bioactive agents from the APA pores. PMID:28144566

  9. Electric field control of magnetization in Cu2O/porous anodic alumina hybrid structures at room temperature

    Science.gov (United States)

    Qi, L. Q.; Liu, H. Y.; Sun, H. Y.; Liu, L. H.; Han, R. S.

    2016-04-01

    Cu2O nanoporous films are deposited on porous anodic alumina (PAA) substrates by DC-reactive magnetron sputtering. This paper focuses on voltage driven magnetization switching in Cu2O/PAA (CP) composite films prepared by DC-reactive magnetron sputtering. By applying a dc electric field, the magnetization of the CP composite films can be controlled in a reversible and reproducible way and shows an analogous on-off behavior. The magnitude of the change in the magnetization was about 75 emu/cm3 as the electric field was switched on and off. Resistive switching behavior was also observed in as-prepared CP composite films. Further analysis indicated that the formation/rupture of conducting filaments composed of oxygen vacancies is likely responsible for the changes in the magnetization as well as in the resistivity. Such reversible change of magnetization controlled by an electric field at room temperature may have applications in spintronics and power efficient data storage technologies.

  10. Synthesis of Nanorods Titanium Dioxide via Anodic Alumina Membrane Template and their Applications in Dye-Sensitized Solar Cells

    Science.gov (United States)

    Suryana, R.; Sehati; Kusumandari

    2016-08-01

    Titanium dioxide (TiO2) nanorods have been successfully synthesized through sol- gel method via Anodic Alumina Membrane (AAM) as template. AAM template was removed using 6 M NaOH solution to obtain TiO2 nanorods only. Then TiO2 nanorods were annealed at 400°C for 2 h. Phase TiO2 nanorods were characterized using X-Ray Diffraction (XRD) and morphology of TiO2 nanorods were observed using Atomic Force Microscopy (AFM). In addition, the I-V meter was used to determine the DSSC efficiency. The XRD patterns showed that all peaks of synthesized-TiO2 indicated anatase phase. AFM images confirmed that TiO2 nanorods have diameters in range 18-30 nm. TiO2 nanorods were mixed with TiO2 nanoparticles having 21 nm in size then it was applied in the DSSC with p-carotene from carrot as dye. The efficiency of DSSC using TiO2 mixed-nanorods and nanoparticles increase about 154.20% compare to using TiO2 nanoparticles only. It is considered that TiO2 nanorod structures can be effective in photon trapping thus many photon interact to dyes to produce many excited-electrons.

  11. Rational Design of Photonic Dust from Nanoporous Anodic Alumina Films: A Versatile Photonic Nanotool for Visual Sensing

    Science.gov (United States)

    Chen, Yuting; Santos, Abel; Wang, Ye; Kumeria, Tushar; Ho, Daena; Li, Junsheng; Wang, Changhai; Losic, Dusan

    2015-08-01

    Herein, we present a systematic study on the development, optimisation and applicability of interferometrically coloured distributed Bragg reflectors based on nanoporous anodic alumina (NAA-DBRs) in the form of films and nanoporous microparticles as visual/colorimetric analytical tools. Firstly, we synthesise a complete palette of NAA-DBRs by galvanostatic pulse anodisation approach, in which the current density is altered in a periodic fashion in order to engineer the effective medium of the resulting photonic films in depth. NAA-DBR photonic films feature vivid colours that can be tuned across the UV-visible-NIR spectrum by structural engineering. Secondly, the effective medium of the resulting photonic films is assessed systematically by visual analysis and reflectometric interference spectroscopy (RIfS) in order to establish the most optimal nanoporous platforms to develop visual/colorimetric tools. Then, we demonstrate the applicability of NAA-DBR photonic films as a chemically selective sensing platform for visual detection of mercury(II) ions. Finally, we generate a new nanomaterial, so-called photonic dust, by breaking down NAA-DBRs films into nanoporous microparticles. The resulting microparticles (μP-NAA-DBRs) display vivid colours and are sensitive towards changes in their effective medium, opening new opportunities for developing advanced photonic nanotools for a broad range of applications.

  12. Electrochemical Fabrication of Pd-Ag Alloy Nanowire Arrays in Anodic Alumina Oxide Template

    Institute of Scientific and Technical Information of China (English)

    Erhong YUE; Gang YU; Yuejun OUYANG; Baicheng WENG; Weiwei SI; Liyuan YE

    2008-01-01

    The synthesis of Pd-Ag alloy nanowires in nanopores of porous anodic aluminum oxide (AAO) template by electrochemical deposition technique was reported.Pd-Ag alloy nanowires with 16%-25% Ag content are expected to serve as candidates of useful nanomaterials for the hydrogen sensors.Scanning electron microscopy (SEM) and energy dispersed X-ray spectroscopy (EDX) were employed to characterize the morphologies and compositions of the Pd-Ag nanowires.X-ray diffraction (XRD) was used to characterize the phase properties of the Pd-Ag nanowires.Pd-Ag alloy nanowire arrays with 17.28%-23.76% Ag content have been successfully fabricated by applying potentials ranging from -0.8 to -1.0 V (vs SCE).The sizes of the alloy nanowires are in agreement with the diameter of AAO nanopores.The underpotential deposition of Ag+ on Pd and Au plays an important role in producing an exceptionally high Ag content in the alloy.Alloy compositions can still be controlled by adjusting the ion concentration ratio of Pd2+ and Ag+ and the electrodeposition processes.XRD shows that nanowires obtained are in the form of alloy of Pd and Ag.

  13. Realisation and advanced engineering of true optical rugate filters based on nanoporous anodic alumina by sinusoidal pulse anodisation

    Science.gov (United States)

    Santos, Abel; Yoo, Jeong Ha; Rohatgi, Charu Vashisth; Kumeria, Tushar; Wang, Ye; Losic, Dusan

    2016-01-01

    This study is the first realisation of true optical rugate filters (RFs) based on nanoporous anodic alumina (NAA) by sinusoidal waves. An innovative and rationally designed sinusoidal pulse anodisation (SPA) approach in galvanostatic mode is used with the aim of engineering the effective medium of NAA in a sinusoidal fashion. A precise control over the different anodisation parameters (i.e. anodisation period, anodisation amplitude, anodisation offset, number of pulses, anodisation temperature and pore widening time) makes it possible to engineer the characteristic reflection peaks and interferometric colours of NAA-RFs, which can be finely tuned across the UV-visible-NIR spectrum. The effect of the aforementioned anodisation parameters on the photonic properties of NAA-RFs (i.e. characteristic reflection peaks and interferometric colours) is systematically assessed in order to establish for the first time a comprehensive rationale towards NAA-RFs with fully controllable photonic properties. The experimental results are correlated with a theoretical model (Looyenga-Landau-Lifshitz - LLL), demonstrating that the effective medium of these photonic nanostructures can be precisely described by the effective medium approximation. NAA-RFs are also demonstrated as chemically selective photonic platforms combined with reflectometric interference spectroscopy (RIfS). The resulting optical sensing system is used to assess the reversible binding affinity between a model drug (i.e. indomethacin) and human serum albumin (HSA) in real-time. Our results demonstrate that this system can be used to determine the overall pharmacokinetic profile of drugs, which is a critical aspect to be considered for the implementation of efficient medical therapies.This study is the first realisation of true optical rugate filters (RFs) based on nanoporous anodic alumina (NAA) by sinusoidal waves. An innovative and rationally designed sinusoidal pulse anodisation (SPA) approach in galvanostatic

  14. Realisation and advanced engineering of true optical rugate filters based on nanoporous anodic alumina by sinusoidal pulse anodisation.

    Science.gov (United States)

    Santos, Abel; Yoo, Jeong Ha; Rohatgi, Charu Vashisth; Kumeria, Tushar; Wang, Ye; Losic, Dusan

    2016-01-21

    This study is the first realisation of true optical rugate filters (RFs) based on nanoporous anodic alumina (NAA) by sinusoidal waves. An innovative and rationally designed sinusoidal pulse anodisation (SPA) approach in galvanostatic mode is used with the aim of engineering the effective medium of NAA in a sinusoidal fashion. A precise control over the different anodisation parameters (i.e. anodisation period, anodisation amplitude, anodisation offset, number of pulses, anodisation temperature and pore widening time) makes it possible to engineer the characteristic reflection peaks and interferometric colours of NAA-RFs, which can be finely tuned across the UV-visible-NIR spectrum. The effect of the aforementioned anodisation parameters on the photonic properties of NAA-RFs (i.e. characteristic reflection peaks and interferometric colours) is systematically assessed in order to establish for the first time a comprehensive rationale towards NAA-RFs with fully controllable photonic properties. The experimental results are correlated with a theoretical model (Looyenga-Landau-Lifshitz - LLL), demonstrating that the effective medium of these photonic nanostructures can be precisely described by the effective medium approximation. NAA-RFs are also demonstrated as chemically selective photonic platforms combined with reflectometric interference spectroscopy (RIfS). The resulting optical sensing system is used to assess the reversible binding affinity between a model drug (i.e. indomethacin) and human serum albumin (HSA) in real-time. Our results demonstrate that this system can be used to determine the overall pharmacokinetic profile of drugs, which is a critical aspect to be considered for the implementation of efficient medical therapies.

  15. Preparation of Porous Anodic Alumina Membrance on Glass Substrate%玻璃基底上多孔氧化铝模板的制备

    Institute of Scientific and Technical Information of China (English)

    李宏

    2014-01-01

    Al thin films were deposited by magnetron sputtering on the glass slide .And then , the porous anodic alumina membrance was fabricated by anodic oxidation in phosphate solution .Scanning electron micro-scope (SEM) showed that the highly ordered porous anodic alumina membrance without barrier layer was fabrica -ted under the condition of 195 V of voltage , 60 s of time .This method can be employed to prepare other kinds of nanostructures on the rigid substrates .%利用磁控溅射在玻璃基底上直接溅射一层铝薄膜,然后利用阳极氧化制备了多孔氧化铝模板,扫描电子显微镜图片显示在195V、60s的条件下获得的多孔氧化铝模板孔道排列规则,且双向贯通。这种方法为在玻璃等硬质基底上制备规则的纳米结构提供了一种有效途径。

  16. An anodic alumina supported Ni-Pt bimetallic plate-type catalysts for multi-reforming of methane, kerosene and ethanol

    KAUST Repository

    Zhou, Lu

    2014-05-01

    An anodic alumina supported Ni-Pt bimetallic plate-type catalyst was prepared by a two-step impregnation method. The trace amount 0.08 wt% of Pt doping efficiently suppressed the nickel particle sintering and improved the nickel oxides reducibility. The prepared Ni-Pt catalyst showed excellent performance during steam reforming of methane, kerosene and ethanol under both 3000 h stationary and 500-time daily start-up and shut-down operation modes. Self-activation ability of this catalyst was evidenced, which was considered to be resulted from the hydrogen spillover effect over Ni-Pt alloy. In addition, an integrated combustion-reforming reactor was proposed in this study. However, the sintering of the alumina support is still a critical issue for the industrialization of Ni-Pt catalyst. Copyright © 2014, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.

  17. A Macroporous TiO2 Oxygen Sensor Fabricated Using Anodic Aluminium Oxide as an Etching Mask

    Directory of Open Access Journals (Sweden)

    Sheng-Po Wu

    2010-01-01

    Full Text Available An innovative fabrication method to produce a macroporous Si surface by employing an anodic aluminium oxide (AAO nanopore array layer as an etching template is presented. Combining AAO with a reactive ion etching (RIE processes, a homogeneous and macroporous silicon surface can be effectively configured by modulating AAO process parameters and alumina film thickness, thus hopefully replacing conventional photolithography and electrochemical etch methods. The hybrid process integration is considered fully CMOS compatible thanks to the low-temperature AAO and CMOS processes. The gas-sensing characteristics of 50 nm TiO2 nanofilms deposited on the macroporous surface are compared with those of conventional plain (or non-porous nanofilms to verify reduced response noise and improved sensitivity as a result of their macroporosity. Our experimental results reveal that macroporous geometry of the TiO2 chemoresistive gas sensor demonstrates 2-fold higher (~33% improved sensitivity than a non-porous sensor at different levels of oxygen exposure. In addition, the macroporous device exhibits excellent discrimination capability and significantly lessened response noise at 500 °C. Experimental results indicate that the hybrid process of such miniature and macroporous devices are compatible as well as applicable to integrated next generation bio-chemical sensors.

  18. A macroporous TiO2 oxygen sensor fabricated using anodic aluminium oxide as an etching mask.

    Science.gov (United States)

    Lu, Chih-Cheng; Huang, Yong-Sheng; Huang, Jun-Wei; Chang, Chien-Kuo; Wu, Sheng-Po

    2010-01-01

    An innovative fabrication method to produce a macroporous Si surface by employing an anodic aluminium oxide (AAO) nanopore array layer as an etching template is presented. Combining AAO with a reactive ion etching (RIE) processes, a homogeneous and macroporous silicon surface can be effectively configured by modulating AAO process parameters and alumina film thickness, thus hopefully replacing conventional photolithography and electrochemical etch methods. The hybrid process integration is considered fully CMOS compatible thanks to the low-temperature AAO and CMOS processes. The gas-sensing characteristics of 50 nm TiO(2) nanofilms deposited on the macroporous surface are compared with those of conventional plain (or non-porous) nanofilms to verify reduced response noise and improved sensitivity as a result of their macroporosity. Our experimental results reveal that macroporous geometry of the TiO(2) chemoresistive gas sensor demonstrates 2-fold higher (∼33%) improved sensitivity than a non-porous sensor at different levels of oxygen exposure. In addition, the macroporous device exhibits excellent discrimination capability and significantly lessened response noise at 500 °C. Experimental results indicate that the hybrid process of such miniature and macroporous devices are compatible as well as applicable to integrated next generation bio-chemical sensors.

  19. Fabrication of novel nanoporous array anodic alumina solid-phase microextraction fiber coating and its potential application for headspace sampling of biological volatile organic compounds

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Zhuomin [School of Chemistry and Chemical Engineering, Sun Yat-sen University, Guangzhou 510275 (China); Wang Qingtang [Key Laboratory of Analysis and Detection for Food Safety of Ministry of Education, College of Chemistry and Chemical Engineering, Fuzhou University, Fuzhou, Fujian 350002 (China); Li Gongke, E-mail: cesgkl@mail.sysu.edu.cn [School of Chemistry and Chemical Engineering, Sun Yat-sen University, Guangzhou 510275 (China)

    2012-05-21

    Highlights: Black-Right-Pointing-Pointer Nanoporous array anodic alumina (NAAA) SPME coating was originally prepared. Black-Right-Pointing-Pointer NAAA SPME coating achieved excellent enrichment capability and selectivity for VOCs. Black-Right-Pointing-Pointer NAAA SPME coating can be applied for the headspace sampling of biological VOCs. - Abstract: In the study, nanoporous array anodic alumina (NAAA) prepared by a simple, rapid and stable two-step anodic oxidization method was introduced as a novel solid-phase microextraction (SPME) fiber coating. The regular nanoporous array structure and chemical composition of NAAA SPME fiber coating was characterized and validated by scanning electron microscopy and energy dispersive spectroscopy, respectively. Compared with the commercial polydimethylsiloxane (PDMS) SPME fiber coating, NAAA SPME fiber coating achieved the higher enrichment capability (1.7-4.7 folds) for the mixed standards of volatile organic compounds (VOCs). The selectivity for volatile alcohols by NAAA SPME fiber coating demonstrated an increasing trend with the increasing polarity of alcohols caused by the gradually shortening carbon chains from 1-undecanol to 1-heptanol or the isomerization of carbon chains of some typical volatile alcohols including 2-ethyl hexanol, 1-octanol, 2-phenylethanol, 1-phenylethanol, 5-undecanol, 2-undecanol and 1-undecanol. Finally, NAAA SPME fiber coating was originally applied for the analysis of biological VOCs of Bailan flower, stinkbug and orange peel samples coupled with gas chromatography-mass spectrometry (GC-MS) detection. Thirty, twenty-seven and forty-four VOCs of Bailan flower, stinkbug and orange peel samples were sampled and identified, respectively. Moreover, the contents of trace 1-octanol and nonanal of real orange peel samples were quantified for the further method validation with satisfactory recoveries of 106.5 and 120.5%, respectively. This work proposed a sensitive, rapid, reliable and convenient

  20. Analysis of nanopore arrangement of porous alumina layers formed by anodizing in oxalic acid at relatively high temperatures

    Science.gov (United States)

    Zaraska, Leszek; Stępniowski, Wojciech J.; Jaskuła, Marian; Sulka, Grzegorz D.

    2014-06-01

    Anodic aluminum oxide (AAO) layers were formed by a simple two-step anodization in 0.3 M oxalic acid at relatively high temperatures (20-30 °C) and various anodizing potentials (30-65 V). The effect of anodizing conditions on structural features of as-obtained oxides was carefully investigated. A linear and exponential relationships between cell diameter, pore density and anodizing potential were confirmed, respectively. On the other hand, no effect of temperature and duration of anodization on pore spacing and pore density was found. Detailed quantitative and qualitative analyses of hexagonal arrangement of nanopore arrays were performed for all studied samples. The nanopore arrangement was evaluated using various methods based on the fast Fourier transform (FFT) images, Delaunay triangulations (defect maps), pair distribution functions (PDF), and angular distribution functions (ADF). It was found that for short anodizations performed at relatively high temperatures, the optimal anodizing potential that results in formation of nanostructures with the highest degree of pore order is 45 V. No direct effect of temperature and time of anodization on the nanopore arrangement was observed.

  1. Effect of Pore Thickness and the State of Polarization on the Optical Properties of Hexagonal Nanoarray of Au/Nanoporous Anodic Alumina Membrane

    Directory of Open Access Journals (Sweden)

    Mohamed Shaban

    2015-01-01

    Full Text Available Hexagonal nanoarrays of Au particles were deposited on nanoporous anodic alumina membrane (NAAM utilizing r.f. magnetron sputtering. The thickness of the NAAMs is adjusted by changing the second anodization time from 5 min to 20 min. The surface morphology, composition, and optical properties are characterized by using SEM, EDX, and spectrophotometer, respectively. The effects of the NAAM thickness and state of polarization on the morphological changes and on the optical properties of the fabricated nanoarrays were addressed. According to the measured optical spectra, the rate of decrease of NAAMs refractive index was found to be 3.825 × 10−4 nm−1. Using the modified Kubelka-Munk radiative transfer model, the energy gap of NAAMs was calculated from diffused reflectance and was decreased from 1.682 to 1.376 as the anodization time increased from 5 to 20 min. Also, the saturation of interference fringes is substantially enhanced, and field enhancement can be achieved due to the excitation and constructive interference of surface plasmon waves by coating NAAMs with the hexagonal nanoarrays of Au. Based on the advantages of the fabrication approach and the enhanced and controlled properties, this new generation of samples can be used as promising building blocks for nanophotonic and nanoelectronics devices.

  2. Investigation of CuInSe2 nanowire arrays with core-shell structure electrodeposited at various duty cycles into anodic alumina templates

    Science.gov (United States)

    Cheng, Yu-Song; Wang, Na-Fu; Tsai, Yu-Zen; Lin, Jia-Jun; Houng, Mau-Phon

    2017-02-01

    Copper indium selenide (CuInSe2) nanowire (NW) arrays were prepared at various electrolyte duty cycles by filling anodic alumina templates through the pulsed electrodeposition technique. X-ray diffraction and scanning electron microscopy (SEM) images showed that the nucleation mechanism of CuInSe2 NW arrays was affected by the electrodeposition duty cycle. Moreover, SEM images showed that the diameter and length of the NWs were 80 nm and 2 μm, respectively. Furthermore, PEDOT/CuInSe2 NW core-shell arrays were fabricated using surfactant-modified CuInSe2 NW surfaces showing the lotus effect. Transmission electron microscopy images confirmed that a core-shell structure was achieved. Current-voltage plots revealed that the CuInSe2 NW arrays were p-type semiconductors; moreover, the core-shell structure improved the diode ideality factor from 3.91 to 2.63.

  3. Fabrication and optical properties of TiO sub 2 nanowire arrays made by sol-gel electrophoresis deposition into anodic alumina membranes

    CERN Document Server

    Lin, Y; Yuan, X Y; Xie, T; Zhang, L D

    2003-01-01

    Ordered TiO sub 2 nanowire arrays have been successfully fabricated into the nanochannels of a porous anodic alumina membrane by sol-gel electrophoretic deposition. After annealing at 500 deg. C, the TiO sub 2 nanowire arrays and the individual nanowires were characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), selected area electron diffraction (SAED) and x-ray diffraction (XRD). SEM and TEM images show that these nanowires are dense and continuous with a uniform diameter throughout their entire length. XRD and SAED analysis together indicate that these TiO sub 2 nanowires crystallize in the anatase polycrystalline structure. The optical absorption band edge of TiO sub 2 nanowire arrays exhibits a blue shift with respect of that of the bulk TiO sub 2 owing to the quantum size effect.

  4. Improvement of Method to Prepare Porous Anodic Alumina Template%多孔阳极氧化铝(PAA)模板制备方法的改进

    Institute of Scientific and Technical Information of China (English)

    高明

    2016-01-01

    通过改进制备方法成功制备出高度有序的多孔阳极氧化铝(porous anodic alumina,P从)模板.对称结构的电解池两侧容室使用等量的、相同浓度的稀硫酸电解液,能够同时对两片铝片接触电解液的面进行阳极氧化,更好的平衡了铝片两侧的压力,有利于提高所制备模板的有序度,同时提高了制备效率.

  5. Understanding and Shaping the Morphology of the Barrier Layer of Supported Porous Anodized Alumina on Gold Underlayers.

    Science.gov (United States)

    Berger, Nele; Es-Souni, Mohammed

    2016-07-12

    Large-area ordered nanorod (NR) arrays of various functional materials can be easily and cost-effectively processed using on-substrate anodized porous aluminum oxide (PAO) films as templates. However, reproducibility in the processing of PAO films is still an issue because they are prone to delamination, and control of fabrication parameters such as electrolyte type and concentration and anodizing time is critical for making robust templates and subsequently mechanically reliable NR arrays. In the present work, we systematically investigate the effects of the fabrication parameters on pore base morphology, devise a method to avoid delamination, and control void formation under the barrier layer of PAO films on gold underlayers. Via systematic control of the anodization parameters, particularly the anodization current density and time, we follow the different stages of void development and discuss their formation mechanisms. The practical aspect of this work demonstrates how void size can be controlled and how void formation can be utilized to control the shape of NR bases for improving the mechanical stability of the NRs.

  6. Direct sub-nanometer scale electron microscopy analysis of anion incorporation to self-ordered anodic alumina layers

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez-Rovira, L.; Lopez-Haro, M.; Hungria, A.B.; El Amrani, K. [Department of Materials Science and Metallurgical Engineering and Inorganic Chemistry, University of Cadiz, Republica Saharaui s/n, 11510 Puerto Real, Cadiz (Spain); Sanchez-Amaya, J.M. [Titania, Ensayos y Proyectos Industriales, S.L. Parque Tecnobahia, Edificio RETSE, Nave 4, 11500 El Puerto de Santa Maria (Cadiz) (Spain); Calvino, J.J. [Department of Materials Science and Metallurgical Engineering and Inorganic Chemistry, University of Cadiz, Republica Saharaui s/n, 11510 Puerto Real, Cadiz (Spain); Botana, F.J., E-mail: javier.botana@uca.e [Department of Materials Science and Metallurgical Engineering and Inorganic Chemistry, University of Cadiz, Republica Saharaui s/n, 11510 Puerto Real, Cadiz (Spain)

    2010-11-15

    Research highlights: {yields} Morphological and chemical characterization at atomic scale of porous alumina layers anodised in ordered regimes. {yields} Characterization based on the use of FEG-SEM, STEM-HAADF, STEM-EELS and STEM-X-EDS. {yields} Nanoscale distribution of P-, C- and S-bearing species in the pore wall. - Abstract: Ordered porous alumina layers prepared by two-step anodising in phosphoric, oxalic and sulphuric acids have been characterized at sub-nanometer scale using electron microscopy techniques. FEG-SEM and STEM-HAADF images allowed estimating the pore size, cell wall and pore wall thicknesses of the layers. Nanoanalytical characterization has been performed by STEM-EELS and STEM-X-EDS. Detailed features of the spatial distribution of anions in the pore wall of the films have been obtained. Maximum concentration of P-species occurs, approximately, at the middle of the pore wall; adjacent to the pore for C-species, whereas the distribution of S-species appears to be uniform.

  7. Enhanced Efficiency of GaAs Single-Junction Solar Cells with Inverted-Cone-Shaped Nanoholes Fabricated Using Anodic Aluminum Oxide Masks

    Directory of Open Access Journals (Sweden)

    Kangho Kim

    2013-01-01

    Full Text Available The GaAs solar cells are grown by low-pressure metalorganic chemical vapor deposition (LP-MOCVD and fabricated by photolithography, metal evaporation, annealing, and wet chemical etch processes. Anodized aluminum oxide (AAO masks are prepared from an aluminum foil by a two-step anodization method. Inductively coupled plasma dry etching is used to etch and define the nanoarray structures on top of an InGaP window layer of the GaAs solar cells. The inverted-cone-shaped nanoholes with a surface diameter of about 50 nm are formed on the top surface of the solar cells after the AAO mask removal. Photovoltaic and optical characteristics of the GaAs solar cells with and without the nanohole arrays are investigated. The reflectance of the AAO nanopatterned samples is lower than that of the planar GaAs solar cell in the measured range. The short-circuit current density increased up to 11.63% and the conversion efficiency improved from 10.53 to 11.57% under 1-sun AM 1.5 G conditions by using the nanohole arrays. Dependence of the efficiency enhancement on the etching depth of the nanohole arrays is also investigated. These results show that the nanohole arrays fabricated with an AAO technique may be employed to improve the light absorption and, in turn, the conversion efficiency of the GaAs solar cell.

  8. Bioinert Anodic Alumina Nanotubes for Targeting of Endoplasmic Reticulum Stress and Autophagic Signaling: A Combinatorial Nanotube-Based Drug Delivery System for Enhancing Cancer Therapy.

    Science.gov (United States)

    Wang, Ye; Kaur, Gagandeep; Chen, Yuting; Santos, Abel; Losic, Dusan; Evdokiou, Andreas

    2015-12-16

    Although nanoparticle-based targeted delivery systems have gained promising achievements for cancer therapy, the development of sophisticated strategies with effective combinatorial therapies remains an enduring challenge. Herein, we report the fabrication of a novel nanomaterial, so-called anodic alumina nanotubes (AANTs) for proof-of-concept cancer therapy by targeting cell signaling networks. This strategy is to target autophagic and endoplasmic reticulum (ER) stress signaling by using thapsigargin (TG)-loaded AANTs cotreated with an autophagy inhibitor 3-methyladenine (3-MA). We first show that AANTs are nontoxic and can activate autophagy in different cell types including human fibroblast cells (HFF), human monocyte cells (THP-1), and human breast cancer cells (MDA-MB 231-TXSA). Treatment with 3-MA at a nontoxic dose reduced the level of autophagy induced by AANTs, and consequently sensitized breast cancer cells to AANTs-induced cellular stresses. To target autophagic and ER stress signaling networking, breast cancer cells were treated with 3-MA together with AANTs loaded with the prototype ER stress inducer TG. We demonstrated that 3-MA enhanced the cancer cell killing effect of AANTs loaded with TG. This effect was associated with enhanced ER stress signaling due to the combination effect of TG and 3-MA. These findings not only demonstrate the excellent biocompatibility of AANTs as novel biomaterials but also provide new opportunities for developing ER- and autophagy-targeted delivery systems for future clinical cancer therapy.

  9. Direct fabrication of 3D graphene on nanoporous anodic alumina by plasma-enhanced chemical vapor deposition

    Science.gov (United States)

    Zhan, Hualin; Garrett, David J.; Apollo, Nicholas V.; Ganesan, Kumaravelu; Lau, Desmond; Prawer, Steven; Cervenka, Jiri

    2016-01-01

    High surface area electrode materials are of interest for a wide range of potential applications such as super-capacitors and electrochemical cells. This paper describes a fabrication method of three-dimensional (3D) graphene conformally coated on nanoporous insulating substrate with uniform nanopore size. 3D graphene films were formed by controlled graphitization of diamond-like amorphous carbon precursor films, deposited by plasma-enhanced chemical vapour deposition (PECVD). Plasma-assisted graphitization was found to produce better quality graphene than a simple thermal graphitization process. The resulting 3D graphene/amorphous carbon/alumina structure has a very high surface area, good electrical conductivity and exhibits excellent chemically stability, providing a good material platform for electrochemical applications. Consequently very large electrochemical capacitance values, as high as 2.1 mF for a sample of 10 mm3, were achieved. The electrochemical capacitance of the material exhibits a dependence on bias voltage, a phenomenon observed by other groups when studying graphene quantum capacitance. The plasma-assisted graphitization, which dominates the graphitization process, is analyzed and discussed in detail.

  10. A three-mask process for fabricating vacuum-sealed capacitive micromachined ultrasonic transducers using anodic bonding.

    Science.gov (United States)

    Yamaner, F Yalçın; Zhang, Xiao; Oralkan, Ömer

    2015-05-01

    This paper introduces a simplified fabrication method for vacuum-sealed capacitive micromachined ultrasonic transducer (CMUT) arrays using anodic bonding. Anodic bonding provides the established advantages of wafer-bondingbased CMUT fabrication processes, including process simplicity, control over plate thickness and properties, high fill factor, and ability to implement large vibrating cells. In addition to these, compared with fusion bonding, anodic bonding can be performed at lower processing temperatures, i.e., 350°C as opposed to 1100°C; surface roughness requirement for anodic bonding is more than 10 times more relaxed, i.e., 5-nm rootmean- square (RMS) roughness as opposed to 0.5 nm for fusion bonding; anodic bonding can be performed on smaller contact area and hence improves the fill factor for CMUTs. Although anodic bonding has been previously used for CMUT fabrication, a CMUT with a vacuum cavity could not have been achieved, mainly because gas is trapped inside the cavities during anodic bonding. In the approach we present in this paper, the vacuum cavity is achieved by opening a channel in the plate structure to evacuate the trapped gas and subsequently sealing this channel by conformal silicon nitride deposition in the vacuum environment. The plate structure of the fabricated CMUT consists of the single-crystal silicon device layer of a silicon-on-insulator wafer and a thin silicon nitride insulation layer. The presented fabrication approach employs only three photolithographic steps and combines the advantages of anodic bonding with the advantages of a patterned metal bottom electrode on an insulating substrate, specifically low parasitic series resistance and low parasitic shunt capacitance. In this paper, the developed fabrication scheme is described in detail, including process recipes. The fabricated transducers are characterized using electrical input impedance measurements in air and hydrophone measurements in immersion. A representative

  11. Enhanced apatite-forming ability and antibacterial activity of porous anodic alumina embedded with CaO-SiO2-Ag2O bioactive materials.

    Science.gov (United States)

    Ni, Siyu; Li, Xiaohong; Yang, Pengan; Ni, Shirong; Hong, Feng; Webster, Thomas J

    2016-01-01

    In this study, to provide porous anodic alumina (PAA) with bioactivity and anti-bacterial properties, sol-gel derived bioactive CaO-SiO2-Ag2O materials were loaded onto and into PAA nano-pores (termed CaO-SiO2-Ag2O/PAA) by a sol-dipping method and subsequent calcination of the gel-glasses. The in vitro apatite-forming ability of the CaO-SiO2-Ag2O/PAA specimens was evaluated by soaking them in simulated body fluid (SBF). The surface microstructure and chemical property before and after soaking in SBF were characterized. Release of ions into the SBF was also measured. In addition, the antibacterial properties of the samples were tested against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus). The results showed that CaO-SiO2-Ag2O bioactive materials were successfully decorated onto and into PAA nano-pores. In vitro SBF experiments revealed that the CaO-SiO2-Ag2O/PAA specimens dramatically enhanced the apatite-forming ability of PAA in SBF and Ca, Si and Ag ions were released from the samples in a sustained and slow manner. Importantly, E. coli and S. aureus were both killed on the CaO-SiO2-Ag2O/PAA (by 100%) samples compared to PAA controls after 3 days of culture. In summary, this study demonstrated that the CaO-SiO2-Ag2O/PAA samples possess good apatite-forming ability and high antibacterial activity causing it to be a promising bioactive coating candidate for implant materials for orthopedic applications.

  12. Nanomechanical humidity detection through porous alumina cantilevers

    Directory of Open Access Journals (Sweden)

    Olga Boytsova

    2015-06-01

    Full Text Available We present here the behavior of the resonance frequency of porous anodic alumina cantilever arrays during water vapor adsorption and emphasize their possible use in the micromechanical sensing of humidity levels at least in the range of 10–22%. The sensitivity of porous anodic aluminium oxide cantilevers (Δf/Δm and the humidity sensitivity equal about 56 Hz/pg and about 100 Hz/%, respectively. The approach presented here for the design of anodic alumina cantilever arrays by the combination of anodic oxidation and photolithography enables easy control over porosity, surface area, geometric and mechanical characteristics of the cantilever arrays for micromechanical sensing.

  13. Preparation of Porous Anodic Alumina/Zinc Oxide Nanowire Arrays by a Coordination Reaction Method%利用配位反应法制备多孔阳极氧化铝/氧化锌纳米线阵列

    Institute of Scientific and Technical Information of China (English)

    张灵翠; 阮永丰; 王丹丽; 邱春霞

    2011-01-01

    A novel method named “coordination reaction method” was developed to fabricate zinc oxide (ZnO) nanowire arrays. The ZnO nanowires in the holes of the porous anodic alumina (PAA) template were synthesized with ammonia as a coordination agent and zinc- amino complex as a precursor by the coordination reaction method. The growth mechanism of ZnO nanowires and the conditions of the coordination reaction were also discussed. The microstructures and morphology of PAA/ZnO assembly were characterized by X-ray diffractometer, scanning electron microscope and transmission electron microscope. The results show that the ZnO nanowires prepared are a polycrystalline structure, and the nanowire arrays possess a periodic array of structure with the same morphological characteristics of PAA template.%研究了一种新型的制备氧化锌(ZnO)纳米线的配位反应法.以氨水为配位剂、氨水与可溶性的锌盐反应配制的锌氨配合物溶液为前驱液,在多孔阳极氧化铝(porous anodic alumina,PAA)模板中沉积了ZnO纳米线.研究了ZnO纳米线的生长机理和配位反应条件.用X射线衍射仪、扫描电子显微镜和透射电子显微镜对PAA/ZnO组装体的组成和形貌进行了表征.结果表明:所制备的ZnO纳米线为多晶结构,纳米线阵列具有周期排列结构,与多孔氧化铝模板形态特征一致.

  14. Ion guiding in alumina capillaries

    DEFF Research Database (Denmark)

    Juhász, Z.; Sulik, B.; Biri, S.

    2009-01-01

    Transmission of a few keV impact energy Ne ions through capillaries in anodic alumina membranes has been studied with different ion counting methods using an energy dispersive electrostatic spectrometer, a multichannel plate (MCP) array and sensitive current-measurement. In the present work, we...

  15. Fabrication and characterazation of anodic alumina with tapered porous structure%磷酸/草酸混合溶液中锥形多孔阳极氧化铝的制备和表征

    Institute of Scientific and Technical Information of China (English)

    徐艳芳; 李晓久; 刘皓

    2016-01-01

    A method to fabricate highly ordered tapered porous anodic alumina (PAA) templates in mixed solution which contains phosphoric acid and oxalic acid was presented. Firstly,highly ordered PAA templates with interpore distance of 495nm were fabricated by two-step method. On this basis, ordered tapered PAA templates with different aspect ratios were fabricated by alternately performing anodization process and pore widening process. Results showed that the aspect ratio of tapered PAA templates is linearly related to the total anodizing time,which could reach more than 100. And the relationship between tapered PAA morphology and partial anodizing time/partial pore widening time was also discussed in detail. The special structure of nano-template could expand the applications of PAA templates in fabricating metal or semiconductor nanowires,photoelectric materials and polymer materials.%提出了以磷酸/草酸混合溶液为电解液制备高度有序锥形多孔阳极氧化铝(PAA)模板的方法。首先采用二次氧化的方法,得到了孔洞排列高度有序且孔间距为495nm的PAA模板。在此基础上,采用阳极氧化过程和扩孔过程交替进行的方法,制备了不同长径比的有序锥形PAA模板。实验结果显示:锥形PAA模板的长径比与总氧化时间线性相关,可达到100以上;还说明了分段氧化时间和分段扩孔时间与锥形孔道形貌之间的关系。这种特殊结构的PAA模板可以大大拓展其在合成金属或半导体纳米线、光电材料以及高分子材料方面的应用范围。

  16. PAA@Co复合薄膜的制备及光学特性研究%Research on the Fabrication of Porous Anodic Alumina Films Embedded with Conanowires and Its Optical Properties

    Institute of Scientific and Technical Information of China (English)

    杨淑敏; 朱玉燕; 韩伟; 顾建军; 岂云开

    2015-01-01

    Alumina thin films with structural colors were fabricated by means of electrochemical oxidation in phosphoric electrolyte. Porous anodic alumina films embedded with Co nanowires in the pores, and highly color saturation and mechanical strength were fabricated by an alternative current electrodeposition. The structural col-ors of films can be effectively tuned by adjusting oxidation time. Multicolor patterns were obtained by an organ-ics-assisted process with multiple electrodeposition. The relation between the changing of structural colors and construction of films was discussed theoretically. The theoretical results are consistent with the experimental ba-sis.%在磷酸电解液中,利用一次阳极氧化工艺成功的制备了具有结构色的多孔氧化铝薄膜。采用交流电沉积方法在氧化铝薄膜的孔洞中沉积金属Co纳米线,得到了高机械强度且具有高饱和度结构色的复合薄膜。控制氧化时间,可以调控复合薄膜结构色的颜色。采用遮挡法,结合多次电沉积工艺,成功的制备出具有彩色图案的复合薄膜。理论分析了薄膜结构色的变化与其微观结构的关系,结果显示,理论分析和实验结果相吻合。

  17. Study of preparation and surface morphology of self-ordered nanoporous alumina; Estudo da preparacao e da morfologia de superficie de alumina nanoporosa auto-organizada

    Energy Technology Data Exchange (ETDEWEB)

    Rodrigues, Elisa Marchezini; Martins, Maximiliano Delany, E-mail: elisamarch@gmail.com, E-mail: MG.mdm@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG. (Brazil); Silva, Ronald Arreguy, E-mail: arregsilva@yahoo.com.br [Centro Universitario de Belo Horizonte (UniBH), Belo Horizonte, MG (Brazil)

    2013-07-01

    Nanoporous alumina is a typical material that exhibits self-ordered nanochannels spontaneously organized in hexagonal shape. Produced by anodizing of metallic aluminum, it has been used as a template for production of materials at the nanoscale. This work aimed to study the preparation of nanoporous alumina by anodic anodizing of metallic aluminum substrates. The nanoporous alumina was prepared following the methodology proposed by Masuda and Fukuda (1995), a two-step method consisting of anodizing the aluminum sample in the potentiostatic mode, removing the layer of aluminum oxide (alumina) formed and then repeat the anodization process under the same conditions as the first anodization. This method produces nanoporous alumina with narrow pore diameter distribution and well-ordered structure. (author)

  18. Microfabrication of an anodic oxide film by anodizing laser-textured aluminium

    OpenAIRE

    2007-01-01

    A simple method for the fabrication of microstructures of an aluminium anodic oxide film (anodic alumina) by anodizing laser-textured aluminium is demonstrated. In the process, the aluminium substrate was first textured by a low power laser beam, and then the textured aluminium was subjected to anodizing, to develop a continuous, thick porous layer on the textured surface. Microstructures with a depth of a few to several tens of micrometres were fabricated successfully on the anodic oxide fil...

  19. Effects of adding alumina to the nickel-zirconia anode materials for solid oxide fuel cells and a two-step sintering method for half-cells

    Science.gov (United States)

    Song, Xiao; Dong, Xiaolei; Li, Ming; Wang, Haiqian

    2016-03-01

    The co-sintering process of half-cells has an important effect on the flatness and performance of solid oxide fuel cells. In this study, we report a two-step sintering method to fabricate flat three-layer half-cells. The first sintering step is a freestanding sintering process at a low temperature (1280 °C). The second sintering step is a constrained sintering process at 1400 °C. The shrinkage of the anode support layer (ASL) and the curvature of the half-cell can be adjusted by adding Al2O3 into the ASL in the first sintering step. Effects of Al2O3 addition on the NiO-YSZ anode material are also studied. We find that NiO reacts with Al2O3 to form NiAl2O4 spinel at the early sintering stage. This reaction transiently promotes the grain growth of NiO. Once the reaction terminates and the NiAl2O4 spinel is formed, the grain growth of NiO will be suppressed, even at higher sintering temperatures. Our results indicate that by a proper amount (approximately 0.2 wt%) of Al2O3 addition, smaller NiO grains can be obtained while the side effects of NiAl2O4 are negligible, which is favorable to increase the conductivity and stability of the ASL, and can enhance the performance of SOFC.

  20. Patterning of rutile TiO{sub 2} surface by ion beam lithography through full-solid masks

    Energy Technology Data Exchange (ETDEWEB)

    Sanz, R; Jaafar, M; Asenjo, A; Vazquez, M [Instituto de Ciencia de Materiales de Madrid (CSIC), 28049, Madrid (Spain); Hernandez-Velez, M [Departamento de Fisica Aplicada, GMNF, Unidad Asociada al ICMM-CSIC, Universidad Autonoma de Madrid, Cantoblanco, 28049, Madrid (Spain); Jensen, J, E-mail: rsanz@nanoate.com [Thin Film Physics, Department of Physics, Chemistry and Biology, Linkoeping University, SE-581 83 Linkoeping (Sweden)

    2010-06-11

    In this work we present and discuss the nanopatterning of rutile TiO{sub 2} single crystal surfaces following their irradiation with energetic heavy ions through a stencil mask of Ni filled self-ordered porous anodic alumina. After etching in HF a corrugated surface morphology is obtained composed of parallel alternate furrows and ridges (or nanobars) 50 nm in diameter and with 100 nm pitch. In addition, isolated, but collapsed, TiO{sub 2} nanorods are seen lying on the patterned surface. The stability of the nanopatterned surface under high temperatures treatments and crystalline properties are analyzed.

  1. Morphology and transmittance of porous alumina on glass substrate

    Energy Technology Data Exchange (ETDEWEB)

    Guo Peitao, E-mail: guopeitao@hotmail.com [Wuhan University of Technology. Wuhan (China); Xia Zhilin [Wuhan University of Technology. Wuhan (China); Key Laboratory of Low Dimensional Materials and Application Technology, Xiangtan University, Ministry of Education, Xiangtan (China); Xue Yiyu [Wuhan University of Technology. Wuhan (China); Huang Caihua [China Three Gorges University, Yichang (China); Zhao Lixin [Wuhan University of Technology. Wuhan (China)

    2011-02-01

    The porous optical film has higher threshold of laser-induced damage than densified films, for the study of mechanism of laser-induced damage of porous optical film with ordered pore structure. Porous anodic alumina (PAA) film with high transmittance on glass substrate has been prepared. Aluminum film was deposited on glass substrate by means of resistance and electron beam heat (EBH) evaporation. Porous alumina was prepared in oxalic acid solution under different anodizing conditions. At normal incidence, the optical transmittance spectrum over 300-1000 nm spectra region was obtained by spectrophotometer. SEM was introduced to analysis the morphology of the porous alumina film. The pore aperture increased with the increase of anodizing voltage, which resulted in a rapid decrease of the pore concentration and the optical thickness of porous alumina film. Damage morphology of porous alumina film is found to be typically defects initiated, and the defect is the pore presented on the film.

  2. Growth of porous anodized alumina on the sputtered aluminum films with 2D–3D morphology for high specific surface area

    Energy Technology Data Exchange (ETDEWEB)

    Liao, M.W.; Chung, C.K., E-mail: ckchung@mail.ncku.edu.tw

    2014-08-01

    The porous anodic aluminum oxide (AAO) with high-aspect-ratio pore channels is widely used as a template for fabricating nanowires or other one-dimensional (1D) nanostructures. The high specific surface area of AAO can also be applied to the super capacitor and the supporting substrate for catalysis. The rough surface could be helpful to enhance specific surface area but it generally results in electrical field concentration even to ruin AAO. In this article, the aluminum (Al) films with the varied 2D–3D morphology on Si substrates were prepared using magnetron sputtering at a power of 50 W–185 W for 1 h at a working pressure of 2.5 × 10⁻¹ Pa. Then, AAO was fabricated from the different Al films by means of one-step hybrid pulse anodizing (HPA) between the positive 40 V and the negative -2 V (1 s:1 s) for 3 min in 0.3 M oxalic acid at a room temperature. The microstructure and morphology of Al films were characterized by X-ray diffraction, scanning electron microscope and atomic force microscope, respectively. Some hillocks formed at the high target power could be attributed to the grain texture growth in the normal orientation of Al(1 1 1). The 3D porous AAO structure which is different from the conventional 2D planar one has been successfully demonstrated using HPA on the film with greatly rough hillock-surface formed at the highest power of 185 W. It offers a potential application of the new 3D AAO to high specific surface area devices.

  3. Growth of porous anodized alumina on the sputtered aluminum films with 2D-3D morphology for high specific surface area

    Science.gov (United States)

    Liao, M. W.; Chung, C. K.

    2014-08-01

    The porous anodic aluminum oxide (AAO) with high-aspect-ratio pore channels is widely used as a template for fabricating nanowires or other one-dimensional (1D) nanostructures. The high specific surface area of AAO can also be applied to the super capacitor and the supporting substrate for catalysis. The rough surface could be helpful to enhance specific surface area but it generally results in electrical field concentration even to ruin AAO. In this article, the aluminum (Al) films with the varied 2D-3D morphology on Si substrates were prepared using magnetron sputtering at a power of 50 W-185 W for 1 h at a working pressure of 2.5 × 10-1 Pa. Then, AAO was fabricated from the different Al films by means of one-step hybrid pulse anodizing (HPA) between the positive 40 V and the negative -2 V (1 s:1 s) for 3 min in 0.3 M oxalic acid at a room temperature. The microstructure and morphology of Al films were characterized by X-ray diffraction, scanning electron microscope and atomic force microscope, respectively. Some hillocks formed at the high target power could be attributed to the grain texture growth in the normal orientation of Al(1 1 1). The 3D porous AAO structure which is different from the conventional 2D planar one has been successfully demonstrated using HPA on the film with greatly rough hillock-surface formed at the highest power of 185 W. It offers a potential application of the new 3D AAO to high specific surface area devices.

  4. 特殊型纳米多孔阳极氧化铝模板的制备%Fabrication of Special-Type Nanoporous Anodic Alumina Templates

    Institute of Scientific and Technical Information of China (English)

    叶秋梅; 宋晔; 刘鹏; 胡隽隽

    2011-01-01

    Porous anodic alumina(PAA) templates have been used widely and studied extensively due to their excellent mechanical and thermal stabilities,highly-ordered hexagonal nanochannel-array architecture and controllable pore structures.In recent years,significant progress has been made in the field of PAA synthesis and a variety of special type PAA templates have been prepared by precisely adjusting the anodizing conditions.By means of the special templates,many novel functional nanomaterials have been synthesized successfully via physical or chemical processing routes.After a brief introduction to the fabrication methods of conventional PAA templates,this paper presents a comprehensive review on the fabrication approaches of PAA templates with special nanopore arrays(e.g.,branched,serrated,bone-shaped or inverted cone nanopores);diamond,triangle or square pore patterns;modulated pore structures with different diameters,lengths,geometries,and periodicity.Several critical factors including the applied electric field,temperature,type and concentration of the electrolyte which determine the pore modulation of PAA are emphasized.Finally,the development trend and future prospects of the special templates are given.%多孔阳极氧化铝(PAA)模板具有六角有序排列的柱形孔,且孔径均匀可调,加之其良好的机械和热稳定性,在纳米材料领域得到了广泛研究和应用。近年来,人们通过改变铝阳极氧化条件制备出了多种特殊型纳米PAA模板,并利用这些模板结合物理或化学方法成功地合成了多种新型纳米功能材料。本文在简要介绍常规纳米PAA模板制备的基础上,较全面地综述了诸如孔道呈分叉形、锯齿形、骨形、倒圆锥形,孔洞呈菱形、三角形、正方形,孔道或孔壁结构呈周期性变化等特殊型纳米PAA模板的制备,揭示了电场强度和电解液种类、温度在PAA孔洞形貌尺寸调控方面的重要性,并展望了这类模板的发展方向及应用前景。

  5. Sequential Vapor Infiltration Treatment Enhances the Ionic Current Rectification Performance of Composite Membranes Based on Mesoporous Silica Confined in Anodic Alumina.

    Science.gov (United States)

    Liang, Yanyan; Liu, Zhengping

    2016-12-20

    Ionic current rectification of nanofluidic diode membranes has been studied widely in recent years because it is analogous to the functionality of biological ion channels in principle. We report a new method to fabricate ionic current rectification membranes based on mesoporous silica confined in anodic aluminum oxide (AAO) membranes. Two types of mesostructured silica nanocomposites, hexagonal structure and nanoparticle stacked structure, were used to asymmetrically fill nanochannels of AAO membranes by a vapor-phase synthesis (VPS) method with aspiration approach and were further modified via sequence vapor infiltration (SVI) treatment. The ionic current measurements indicated that SVI treatment can modulate the asymmetric ionic transport in prepared membranes, which exhibited clear ionic current rectification phenomenon under optimal conditions. The ionic current rectifying behavior is derived from the asymmetry of surface conformations, silica species components, and hydrophobic wettability, which are created by the asymmetrical filling type, silica depositions on the heterogeneous membranes, and the condensation of silanol groups. This article provides a considerable strategy to fabricate composite membranes with obvious ionic current rectification performance via the cooperation of the VPS method and SVI treatment and opens up the potential of mesoporous silica confined in AAO membranes to mimic fluid transport in biological processes.

  6. Superhydrophilicity of a nanofiber-covered aluminum surface fabricated via pyrophosphoric acid anodizing

    Science.gov (United States)

    Nakajima, Daiki; Kikuchi, Tatsuya; Natsui, Shungo; Suzuki, Ryosuke O.

    2016-12-01

    A superhydrophilic aluminum surface covered by numerous alumina nanofibers was fabricated via pyrophosphoric acid anodizing. High-density anodic alumina nanofibers grow on the bottom of a honeycomb oxide via anodizing in concentrated pyrophosphoric acid. The water contact angle on the nanofiber-covered aluminum surface decreased with time after a 4 μL droplet was placed on the surface, and a superhydrophilic behavior with a contact angle measuring 2.2° was observed within 2 s; this contact angle is considerably lower than those observed for electropolished and porous alumina-covered aluminum surfaces. There was no dependence of the superhydrophilicity on the density of alumina nanofibers fabricated via different constant voltage anodizing conditions. The superhydrophilic property of the surface covered by anodic alumina nanofibers was maintained during an exposure test for 359 h. The quick-drying and snow-sliding behaviors of the superhydrophilic aluminum covered with anodic alumina nanofibers were demonstrated.

  7. Free-standing alumina nanobottles and nanotubes pre-integrated into nanoporous alumina membranes

    Science.gov (United States)

    Fang, Jinghua; Levchenko, Igor; (Ken Ostrikov, Kostya

    2014-08-01

    A novel interfacial structure consisting of long (up to 5 μm), thin (about 300 nm), highly-ordered, free-standing, highly-reproducible aluminum oxide nanobottles and long tubular nanocapsules attached to a rigid, thin (less than 1 μm) nanoporous anodic alumina membrane is fabricated by simple, fast, catalyst-free, environmentally friendly voltage-pulse anodization. A growth mechanism is proposed based on the formation of straight channels in alumina membrane by anodization, followed by neck formation due to a sophisticated voltage control during the process. This process can be used for the fabrication of alumina nanocontainers with highly controllable geometrical size and volume, vitally important for various applications such as material and energy storage, targeted drug and diagnostic agent delivery, controlled drug and active agent release, gene and biomolecule reservoirs, micro-biologically protected platforms, nano-bioreactors, tissue engineering and hydrogen storage.

  8. Growth behavior of anodic oxide formed by aluminum anodizing in glutaric and its derivative acid electrolytes

    Science.gov (United States)

    Nakajima, Daiki; Kikuchi, Tatsuya; Natsui, Shungo; Suzuki, Ryosuke O.

    2014-12-01

    The growth behavior of anodic oxide films formed via anodizing in glutaric and its derivative acid solutions was investigated based on the acid dissociation constants of electrolytes. High-purity aluminum foils were anodized in glutaric, ketoglutaric, and acetonedicarboxylic acid solutions under various electrochemical conditions. A thin barrier anodic oxide film grew uniformly on the aluminum substrate by glutaric acid anodizing, and further anodizing caused the film to breakdown due to a high electric field. In contrast, an anodic porous alumina film with a submicrometer-scale cell diameter was successfully formed by ketoglutaric acid anodizing at 293 K. However, the increase and decrease in the temperature of the ketoglutaric acid resulted in non-uniform oxide growth and localized pitting corrosion of the aluminum substrate. An anodic porous alumina film could also be fabricated by acetonedicarboxylic acid anodizing due to the relatively low dissociation constants associated with the acid. Acid dissociation constants are an important factor for the fabrication of anodic porous alumina films.

  9. In situ fabrication of ultrathin porous alumina and its application for nanopatterning Au nanocrystals on the surface of ion-sensitive field-effect transistors.

    Science.gov (United States)

    Kisner, A; Heggen, M; Fischer, W; Tillmann, K; Offenhäusser, A; Kubota, L T; Mourzina, Y

    2012-12-07

    In situ fabrication in a single step of thin films of alumina exhibiting a thickness of less than 100 nm and nanopores with a highly regular diameter distribution in order to pattern nanostructures over field-effect devices is a critical issue and has not previously been demonstrated. Here we report the fabrication in situ of 50 nm thick ultrathin nanoporous alumina membranes with a regular pore size directly over metal-free gate ion-sensitive field-effect transistors. Depositing thin films of aluminum by an electron beam at a relatively low rate of deposition on top of chips containing the transistors and using a conventional single-step anodization process permits the production of a well-adhering nanoporous ultrathin layer of alumina on the surface of the devices. The anodization process does not substantially affect the electrical properties of the transistors. The small thickness and pore size of ultrathin alumina membranes allow them to be sequentially employed as masks for patterning Au nanocrystals grown by an electroless approach directly on the top of the transistors. The patterning process using a wet chemical approach enables the size of the patterned crystals to be controlled not only by the dimensions of the pores of alumina, but also by the concentration of the reactants employed. Surface modification of these nanocrystals with alkanethiol molecules demonstrates that the electrostatic charge of the functional groups of the molecules can modulate the electrical characteristics of the transistors. These results represent substantial progress towards the development of novel nanostructured arrays on top of field-effect devices that can be applied for chemical sensing or non-volatile memories.

  10. Photoluminescence properties of heat-treated porous alumina films formed in oxalic acid

    Energy Technology Data Exchange (ETDEWEB)

    Vrublevsky, I., E-mail: vrublevsky@bsuir.edu.b [Belarusian State University of Informatics and Radioelectronics Minsk, Department of Micro and Nanoelectronics, 220013 Minsk (Belarus); Chernyakova, K. [Belarusian State University of Informatics and Radioelectronics Minsk, Department of Micro and Nanoelectronics, 220013 Minsk (Belarus); Ispas, A.; Bund, A.; Gaponik, N.; Dubavik, A. [Technische Universitaet Dresden, Physikalische Chemie und Elektrochemie, 01062 Dresden (Germany)

    2011-05-15

    Photoluminescence and optical properties of as-anodized and heat-treated at 500 {sup o}C porous alumina films formed in a 0.3 M oxalic acid at 40 V have been studied. The FTIR indicates that the oxalate ions are embedded in the anodic alumina as chelating bidentate structures and further heating up to 500 {sup o}C does not cause any change in ion coordination. The results of time-resolved spectroscopy show the presence of two luminescence centers both in the as-anodized and heat-treated anodic alumina films with lifetimes of about 0.25 and 4.0 ns. The F{sup +}-centers in anodic alumina are responsible for the luminescence peak at about 420 nm, with a lifetime of about 4.0 ns. The luminescence peak at about 480 nm, with lifetime of about 0.25 ns, can be attributed to the luminescence of carboxylate ions existing in bulk of anodic alumina. - Research highlights: {yields} Photoluminescence and optical properties of porous alumina films have been studied. {yields} In anodic alumina the oxalate ions are embedded as chelating bidentate structures. {yields} The results show the presence of two luminescence centers. {yields} The F{sup +}-centers are responsible for the peak at 420 nm with a lifetime of 4.0 ns. {yields} The peak at 480 nm with a lifetime of 0.25 ns can be attributed to carboxylate ions.

  11. Self-ordered nanopore arrays through hard anodization assisted by anode temperature ramp

    Science.gov (United States)

    Mohammadniaei, M.; Maleki, K.; Kashi, M. Almasi; Ramezani, A.; Mayamei, Y.

    2016-10-01

    In the present work, hard anodization assisted by anode temperature ramp was employed to fabricate self-ordered nanoporous alumina in the wide range of interpore distances (259-405 nm) in pure oxalic acid and mixture of oxalic and phosphoric acid solutions. Anode temperature ramp technique was employed to adjust the anodization current density to optimize the self-ordering of the nanopore arrays in the interpore range in which no ordered self-assembled hard anodized anodic aluminum oxide has reported. It is found that the certain ratios of oxalic and phosphoric acid solutions in this anodization technique increased self-ordering of the nanopores especially for anodization voltages over the 170 V by increasing alumina's viscous flow which could lead to decrease the overall current density of anodization, yet leveled up by anode temperature ramp. However, below 150 V anodization voltage, the ratio of interpore distance to the anodization voltage of the both anodization techniques was the same (~2 nm/V), while above this voltage, it increased to about 2.2 nm/V.

  12. Fabrication of anodic aluminum oxide with incorporated chromate ions

    Science.gov (United States)

    Stępniowski, Wojciech J.; Norek, Małgorzata; Michalska-Domańska, Marta; Bombalska, Aneta; Nowak-Stępniowska, Agata; Kwaśny, Mirosław; Bojar, Zbigniew

    2012-10-01

    The anodization of aluminum in 0.3 M chromic acid is studied. The influence of operating conditions (like anodizing voltage and electrolyte's temperature) on the nanoporous anodic aluminum oxide geometry (including pore diameter, interpore distance, the oxide layer thickness and pores density) is thoroughly investigated. The results revealed typical correlations of the anodic alumina nanopore geometry with operating conditions, such as linear increase of pore diameter and interpore distance with anodizing voltage. The anodic aluminum oxide is characterized by a low pores arrangement, as determined by Fast Fourier transforms analyses of the FE-SEM images, which translates into a high concentration of oxygen vacancies. Moreover, an optimal experimental condition where chromate ions are being successfully incorporated into the anodic alumina walls, have been determined: the higher oxide growth rate the more chromate ions are being trapped. The trapped chromate ions and a high concentration of oxygen vacancies make the anodic aluminum oxide a promising luminescent material.

  13. Anodic bonding of diamond to glass

    Energy Technology Data Exchange (ETDEWEB)

    Fuentes, R. [Materials and Technologies Corp., Poughkeepsie, NY (United States); Trolio, L.M. [Geo-Centers, Inc., Fort Washington, MD (United States); Butler, J.E. [Naval Research Lab., Washington, DC (United States)

    1995-12-31

    A method is described for anodically bonding smooth nanocrystalline diamond films to glass substrates to form extremely flat diamond membranes with the smoothest side available of patterning absorber structures to form masks for proximity focused x-ray lithography.

  14. Iron films deposited on porous alumina substrates

    Science.gov (United States)

    Yamada, Yasuhiro; Tanabe, Kenichi; Nishida, Naoki; Kobayashi, Yoshio

    2016-12-01

    Iron films were deposited on porous alumina substrates using an arc plasma gun. The pore sizes (120 - 250 nm) of the substrates were controlled by changing the temperature during the anodic oxidation of aluminum plates. Iron atoms penetrated into pores with diameters of less than 160 nm, and were stabilized by forming γ-Fe, whereas α-Fe was produced as a flat plane covering the pores. For porous alumina substrates with pore sizes larger than 200 nm, the deposited iron films contained many defects and the resulting α-Fe had smaller hyperfine magnetic fields. In addition, only a very small amount of γ-Fe was obtained. It was demonstrated that the composition and structure of an iron film can be affected by the surface morphology of the porous alumina substrate on which the film is grown.

  15. Structural engineering of nanoporous anodic aluminium oxide by pulse anodization of aluminium.

    Science.gov (United States)

    Lee, Woo; Schwirn, Kathrin; Steinhart, Martin; Pippel, Eckhard; Scholz, Roland; Gösele, Ulrich

    2008-04-01

    Nanoporous anodic aluminium oxide has traditionally been made in one of two ways: mild anodization or hard anodization. The first method produces self-ordered pore structures, but it is slow and only works for a narrow range of processing conditions; the second method, which is widely used in the aluminium industry, is faster, but it produces films with disordered pore structures. Here we report a novel approach termed "pulse anodization" that combines the advantages of the mild and hard anodization processes. By designing the pulse sequences it is possible to control both the composition and pore structure of the anodic aluminium oxide films while maintaining high throughput. We use pulse anodization to delaminate a single as-prepared anodic film into a stack of well-defined nanoporous alumina membrane sheets, and also to fabricate novel three-dimensional nanostructures.

  16. Modelling the growth of porous alumina matrix for creating hyperbolic media

    Science.gov (United States)

    Aryslanova, E. M.; Alfimov, A. V.; Chivilikhin, S. A.

    2016-08-01

    Porous aluminum oxide is a regular self-assembled structure. During anodization it is possible to control nano-parameters of the structure using macroscopic parameters of anodization. Porous alumina films can be used as a template for the creation of hyperbolic media. In this work we consider the anodization process, our model takes into account the influence of layers of aluminum and electrolyte on the rate of growth of aluminum oxide, as well as the effect of surface diffusion. As a result of our model we obtain the minimum distance between centers of alumina pores in the beginning of anodizing process. We also present the results obtained by numerical modelling of hyperbolic media based on porous alumina film.

  17. Optimization of Aluminum Anodization Conditions for the Fabrication of Nanowires by Electrodeposition

    Science.gov (United States)

    Fucsko, Viola

    2005-01-01

    Anodized alumina nanotemplates have a variety of potential applications in the development of nanotechnology. Alumina nanotemplates are formed by oxidizing aluminum film in an electrolyte solution.During anodization, aluminum oxidizes, and, under the proper conditions, nanometer-sized pores develop. A series of experiments was conducted to determine the optimal conditions for anodization. Three-micrometer thick aluminum films on silicon and silicon oxide substrates were anodized using constant voltages of 13-25 V. 0.1-0.3M oxalic acid was used as the electrolyte. The anodization time was found to increase and the overshooting current decreased as both the voltage and the electrolyte concentrations were decreased. The samples were observed under a scanning electron microscope. Anodizing with 25V in 0.3M oxalic acid appears to be the best process conditions. The alumina nanotemplates are being used to fabricate nanowires by electrodeposition. The current-voltage characteristics of copper nanowires have also been studied.

  18. Nanoparticles in alumina: Microscopy and Theory

    Science.gov (United States)

    Idrobo, Juan C.; Halabica, Andrej; Rashkeev, Sergey; Glazoff, Michael V.; Boatner, Lynn A.; Haglund, Richard F.; Pennycook, Stephen. J.; Pantelides, Sokrates T.

    2007-03-01

    Transition-metal nanoparticles formed by ion implantation in alumina can be used to modify the optical properties of naturally oxidized and anodized aluminum. Here, we report atomic-resolution Z-contrast images using a scanning transmission electron microscope (STEM) of CoFe and other metal nanoparticles in alumina. We also report electron energy loss spectra (EELS) and relate them to visual appearance and optical properties. Finally, we report first-principles density- functional calculations of nucleation mechanisms for these nanoparticles. This research was sponsored by the Office of Basic Energy Sciences, Division of Materials Sciences and Engineering, U.S. Department of Energy, under contract DE-AC05- 00OR22725 with Oak Ridge National Laboratory, managed and operated by UT-Battelle, by NSF grant No. DMR-0513048, and by Alcoa Inc.

  19. Clay Mask Workshop

    Science.gov (United States)

    Gamble, David L.

    2012-01-01

    Masks can represent so many things, such as emotions (happy, sad, fearful) and power. The familiar "comedy and tragedy" masks, derived from ancient Greek theater, are just one example from mask history. Death masks from the ancient Egyptians influenced the ancient Romans into creating similar masks for their departed. Masks can represent many…

  20. Clay Mask Workshop

    Science.gov (United States)

    Gamble, David L.

    2012-01-01

    Masks can represent so many things, such as emotions (happy, sad, fearful) and power. The familiar "comedy and tragedy" masks, derived from ancient Greek theater, are just one example from mask history. Death masks from the ancient Egyptians influenced the ancient Romans into creating similar masks for their departed. Masks can represent many…

  1. Electron optical mask projector with a photocathode for miniaturization

    Science.gov (United States)

    Moellenstedt, G.; Speidel, R.; Dostmann, M.; Martin, F.; Mayr, M.

    1981-06-01

    The projector was developed with an image converter consisting of a masked photocathode and a plane anode grid. The mask structure to be demagnified is on a quartz glass plate in a thin layer of Ti02 strongly absorbing ultraviolet light. A photoemissive layer is deposited by evaporation on the whole front side of the plate. For the demagnification of the electron image of the mask, a system is used consisting of two geometrically similar magnetic lenses in a telescopic arrangement.

  2. Corrosion of Zinc Ferrite Based Inert Anodes in AlF3-NaF-Al2O3 Melts Under Conditions of Anodic Polarization

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    ZnFe2O4-based inert anodes were made to conduct the aluminum electrolysis tests. The corrosion behaviors of the inert anodes were examined and discussed. Experiment results prove that: (1) ZnFe2O4-based inert anodes are good corrosion resistant to AlF3-NaF-Al2O3 melts under the conditions of anodic polarization; (2) High anodic current density(>1.5 A·cm-2), high alumina concentration and low ratio of NaF/AlF3 in the molten salts will be the most important conditions for using inert anode.

  3. Behavior of alumina barrier layer in the supporting electrolytes for deposition of nanowired materials

    Energy Technology Data Exchange (ETDEWEB)

    Jagminas, Arunas, E-mail: jagmin@ktl.mii.l [Institute of Chemistry, A. Gostauto 9, 01108 Vilnius (Lithuania); Cesuniene, Asta [Institute of Chemistry, A. Gostauto 9, 01108 Vilnius (Lithuania); Vrublevsky, Igor [Department of Microelectronics, Belarusian State University of Informatics and Radioelectronics, 6 Brovka str, Minsk 220013 (Belarus); Jasulaitiene, Vitalija; Ragalevicius, Rimas [Institute of Chemistry, A. Gostauto 9, 01108 Vilnius (Lithuania)

    2010-03-30

    In this study, we report the results obtained investigating the behavior of sulfuric and chromic acid alumina templates in typical supporting electrolytes frequently used for alternating current (ac) deposition of various nm-scaled materials. Qualitative analysis of voltammetric profiles taken for as-grown, ac-treated and annealed alumina films in a conventional tetraborate re-anodizing solution revealed dramatical changes in the properties of alumina barrier layer during ac treatment in these supporting electrolytes even at low current density. These changes were related here with the transport of protons through the barrier layer during ac treatment, discharge at the metal/oxide interface and hydrogenation of alumina material by hydrogen atoms in an upward way. This conclusion comes from the behavior of Pt/Hg|alumina|Me{sup z+} electrode and the valence band X-ray photoelectron spectra taken from the inner part of alumina barrier layer material before and after the ac treatment.

  4. The Role of Anode Manufacturing Processes in Net Carbon Consumption

    Directory of Open Access Journals (Sweden)

    Khalil Khaji

    2016-05-01

    Full Text Available Carbon anodes are consumed in electrolysis cells during aluminum production. Carbon consumption in pre-bake anode cells is 400–450 kg C/t Al, considerably higher than the theoretical consumption of 334 kg C/t Al. This excess carbon consumption is partly due to the anode manufacturing processes. Net carbon consumption over the last three years at Emirates Aluminium (EMAL, also known as Emirates Global Aluminium (EGA Al Taweelah was analyzed with respect to anode manufacturing processes/parameters. The analysis indicates a relationship between net carbon consumption and many manufacturing processes, including anode desulfurization during anode baking. Anode desulfurization appears to increase the reaction surface area, thereby helping the Boudouard reaction between carbon and carbon dioxide in the electrolysis zone, as well as reducing the presence of sulfur which could inhibit this reaction. This paper presents correlations noted between anode manufacturing parameters and baked anode properties, and their impact on the net carbon consumption in electrolytic pots. Anode reactivities affect the carbon consumption in the pots during the electrolysis of alumina. Pitch content in anodes, impurities in anodes, and anode desulfurization during baking were studied to find their influence on anode reactivities. The understanding gained through this analysis helped reduce net carbon consumption by adjusting manufacturing processes. For an aluminum smelter producing one million tonnes of aluminum per year, the annual savings could be as much as US $0.45 million for every kg reduction in net carbon consumption.

  5. Reuse of activated alumina

    Energy Technology Data Exchange (ETDEWEB)

    Hobensack, J.E. [Martin Marietta Energy Systems, Inc., Piketon, OH (United States)

    1991-12-31

    Activated alumina is used as a trapping media to remove trace quantities of UF{sub 6} from process vent streams. The current uranium recovery method employs concentrated nitric acid which destroys the alumina pellets and forms a sludge which is a storage and disposal problem. A recently developed technique using a distilled water rinse followed by three dilute acid rinses removes on average 97% of the uranium, and leaves the pellets intact with crush strength and surface area values comparable with new material. Trapping tests confirm the effectiveness of the recycled alumina as UF{sub 6} trapping media.

  6. Antibacterial activity of zinc oxide-coated nanoporous alumina

    Energy Technology Data Exchange (ETDEWEB)

    Skoog, S.A. [Joint Department of Biomedical Engineering, University of North Carolina and North Carolina State University, Box 7115, Raleigh, NC 27695-7115 (United States); Bayati, M.R. [Department of Materials Science and Engineering, North Carolina State University, Box 7907, Raleigh, NC 27695-7907 (United States); Petrochenko, P.E. [Joint Department of Biomedical Engineering, University of North Carolina and North Carolina State University, Box 7115, Raleigh, NC 27695-7115 (United States); Division of Biology, Office of Science and Engineering Laboratories, Center for Devices and Radiological Health, U.S. Food and Drug Administration, Silver Spring, MD 20993 (United States); Stafslien, S.; Daniels, J.; Cilz, N. [Center for Nanoscale Science and Engineering, North Dakota State University, 1805 Research Park Drive, Fargo, ND 58102 (United States); Comstock, D.J.; Elam, J.W. [Energy Systems Division, Argonne National Laboratory, Argonne, IL 60439 (United States); Narayan, R.J., E-mail: roger_narayan@msn.com [Joint Department of Biomedical Engineering, University of North Carolina and North Carolina State University, Box 7115, Raleigh, NC 27695-7115 (United States); Department of Materials Science and Engineering, North Carolina State University, Box 7907, Raleigh, NC 27695-7907 (United States)

    2012-07-25

    Highlights: Black-Right-Pointing-Pointer Atomic layer deposition was used to deposit ZnO on nanoporous alumina membranes. Black-Right-Pointing-Pointer Scanning electron microscopy showed continuous coatings of zinc oxide nanocrystals. Black-Right-Pointing-Pointer Activity against B. subtilis, E. coli, S. aureus, and S. epidermidis was shown. - Abstract: Nanoporous alumina membranes, also known as anodized aluminum oxide membranes, are being investigated for use in treatment of burn injuries and other skin wounds. In this study, atomic layer deposition was used for coating the surfaces of nanoporous alumina membranes with zinc oxide. Agar diffusion assays were used to show activity of zinc oxide-coated nanoporous alumina membranes against several bacteria found on the skin surface, including Bacillus subtilis, Escherichia coli, Staphylococcus aureus, and Staphylococcus epidermidis. On the other hand, zinc oxide-coated nanoporous alumina membranes did not show activity against Pseudomonas aeruginosa, Enterococcus faecalis, and Candida albicans. These results suggest that zinc oxide-coated nanoporous alumina membranes have activity against some Gram-positive and Gram-negative bacteria that are associated with skin colonization and skin infection.

  7. Alumina Concentration Detection Based on the Kernel Extreme Learning Machine.

    Science.gov (United States)

    Zhang, Sen; Zhang, Tao; Yin, Yixin; Xiao, Wendong

    2017-09-01

    The concentration of alumina in the electrolyte is of great significance during the production of aluminum. The amount of the alumina concentration may lead to unbalanced material distribution and low production efficiency and affect the stability of the aluminum reduction cell and current efficiency. The existing methods cannot meet the needs for online measurement because industrial aluminum electrolysis has the characteristics of high temperature, strong magnetic field, coupled parameters, and high nonlinearity. Currently, there are no sensors or equipment that can detect the alumina concentration on line. Most companies acquire the alumina concentration from the electrolyte samples which are analyzed through an X-ray fluorescence spectrometer. To solve the problem, the paper proposes a soft sensing model based on a kernel extreme learning machine algorithm that takes the kernel function into the extreme learning machine. K-fold cross validation is used to estimate the generalization error. The proposed soft sensing algorithm can detect alumina concentration by the electrical signals such as voltages and currents of the anode rods. The predicted results show that the proposed approach can give more accurate estimations of alumina concentration with faster learning speed compared with the other methods such as the basic ELM, BP, and SVM.

  8. Anodic oxidation

    CERN Document Server

    Ross, Sidney D; Rudd, Eric J; Blomquist, Alfred T; Wasserman, Harry H

    2013-01-01

    Anodic Oxidation covers the application of the concept, principles, and methods of electrochemistry to organic reactions. This book is composed of two parts encompassing 12 chapters that consider the mechanism of anodic oxidation. Part I surveys the theory and methods of electrochemistry as applied to organic reactions. These parts also present the mathematical equations to describe the kinetics of electrode reactions using both polarographic and steady-state conditions. Part II examines the anodic oxidation of organic substrates by the functional group initially attacked. This part particular

  9. Anodization of Aluminium using a fast two-step process

    Indian Academy of Sciences (India)

    Murugaiya Sridar Ilango; Amruta Mutalikdesai; Sheela K Ramasesha

    2016-01-01

    Ultra-fast two-step anodization method is developed for obtaining ordered nano-pores on aluminium (Al) foil. First anodization was carried out for 10 min, followed by 3 min of second anodization at high voltage (150 V) compared to previous reports of anodization times of 12 h (40-60 V). The pore dimensions on anodized alumina are 180 nm for pore diameter and 130 nm for inter-pore distance. It was evident that by increasing the anodization voltage to 150 V, the diameter of the pores formed was above 150 nm. The electrolyte and its temperature affect the shape and size of the pore formation. At lower anodization temperature, controlled pore formation was observed. The anodized samples were characterized using the field emission scanning electron microscope (FE-SEM) to determine the pore diameter and inter-pore distance. Using UVVisible spectroscopy, the reflectance spectra of anodized samples were measured. The alumina (Al2O3) peaks were identified by x-ray diffraction (XRD) technique. The x-ray photo electron spectroscopy (XPS) analysis confirmed the Al 2p peak at 73.1 eV along with the oxygen O 1s at 530.9 eV and carbon traces C 1s at 283.6 eV.

  10. Impurity-defect structure of anodic aluminum oxide produced by two-sided anodizing in tartaric acid

    Science.gov (United States)

    Chernyakova, K. V.; Vrublevsky, I. A.; Ivanovskaya, M. I.; Kotsikau, D. A.

    2012-03-01

    Porous aluminum oxide is prepared in a 0.4 M aqueous solution of tartaric acid by two-sided anodizing. Fourier Transform IR spectroscopy (FTIR) data reveal the presence, in the alumina, of unoxidized tartarate ions, as well as products of their partial (radical organic products and CO) and complete (CO2) oxidation. Carboxylate ions and elemental carbon contained in the anodic oxide impart a gray color to the films.

  11. Formation of Anodic Aluminum Oxide with Branched and Meshed Pores.

    Science.gov (United States)

    Kim, Byeol; Lee, Jin Seok

    2016-06-01

    Anodic aluminum oxide (AAO), with a self-ordered hexagonal array, is important for various applications in nanofabrication including as the fabrication of nanotemplates and other nanostructures. With the consideration, there have been many efforts to control the characteristic parameters of porous anodic alumina by adjustment of the anodizing conditions such as the electrolyte, temperature, applied potential, and Al purity. In particular, impurities in Al are changing the morphology of an alumina film; however, the formation mechanism has not yet been explained. In this work, we anodized a high purity (99.999%, Al(high)) and low purity (99.8%, Al(low)) aluminum foil by a two-step anodization process in an oxalic acid solution or phosphoric acid. It was found that the purity of aluminum foil has influenced the morphology of the alumina film resulting in branched and meshed pores. Also, electrochemical analysis indicated that the branched and meshed pores in the low-purity Al foil formed by the presence of impurities. Impurities act as defects and change the general growth mechanism for pore formation by inducing an electric field imbalance during anodization. This work contributes to the research field of topographical chemistry and applied fields including nanofabrication.

  12. Modelling the growth process of porous aluminum oxide film during anodization

    Science.gov (United States)

    Aryslanova, E. M.; Alfimov, A. V.; Chivilikhin, S. A.

    2015-11-01

    Currently it has become important for the development of metamaterials and nanotechnology to obtain regular self-assembled structures. One such structure is porous anodic alumina film that consists of hexagonally packed cylindrical pores. In this work we consider the anodization process, our model takes into account the influence of layers of aluminum and electrolyte on the rate of growth of aluminum oxide, as well as the effect of surface diffusion. In present work we consider those effects. And as a result of our model we obtain the minimum distance between centers of alumina pores in the beginning of anodizing process.

  13. Bauxite and alumina

    Science.gov (United States)

    Bray, E.L.

    2010-01-01

    The article reports on the global market performance of bauxite and alumina in 2009 and presents an outlook for their 2010 performance. There were only several U.S. states that could produce bauxite and bauxitic clays including Georgia, Arkansas, and Alabama. The prices for imported refractory-grade calcined bauxite ranged between 426 U.S. dollars and 554 dollars per ton.

  14. Prediction of alumina penetration

    Energy Technology Data Exchange (ETDEWEB)

    Mandell, D A

    1993-02-01

    The MESA hydrocode was used to predict two-dimensional tests of L/D 10 and L/D 15 tungsten rods impacting AD 90 alumina with a steel backing. The residual penetration into the steel is the measured quantity in these experiments conducted at the Southwest Research Institute (SWR). The interface velocity as a function of time between an alumina target and a lithium fluoride window, impacted by an alumina disk at velocities between 544 m/s and 2329 m/s, was also predicted. These one-dimensional flyer plate experiments were conducted at Sandia National Laboratories using Coors AD 995 alumina. The material strength and fracture models are important in the prediction of ceramic experiments. The models used in these predictions are discussed. The penetrations in the two-dimensional tests were predicted to 11.4 percent or better. In five of the six experiments, the predicted penetration depth was deeper than the measured value. This trend is expected since the calculation is based on ideal conditions. The results show that good agreement between the 1-D flyer plate data and the MESA predictions exists at the lower impact velocities, but the maximum velocity is overpredicted as the flyer plate velocity increases. At a flyer plate velocity of 2329 m/s the code overpredicted the data by 12.3 percent.

  15. Alumina Technology Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2002-02-01

    The Alumina Technology Roadmap outlines a comprehensive long-term research and development plan that defines the industry's collective future and establishes a clear pathway forward. It emphasizes twelve high-priority R&D areas deemed most significant in addressing the strategic goals.

  16. Visual masking & schizophrenia

    Directory of Open Access Journals (Sweden)

    Michael H. Herzog

    2015-06-01

    Full Text Available Visual masking is a frequently used tool in schizophrenia research. Visual masking has a very high sensitivity and specificity and masking paradigms have been proven to be endophenotypes. Whereas masking is a powerful technique to study schizophrenia, the underlying mechanisms are discussed controversially. For example, for more than 25 years, masking deficits of schizophrenia patients were mainly attributed to a deficient magno-cellular system (M-system. Here, we show that there is very little evidence that masking deficits are magno-cellular deficits. We will discuss the magno-cellular and other approaches in detail and highlight their pros and cons.

  17. Preparation and characterization of superhydrophobic surfaces based on hexamethyldisilazane-modified nanoporous alumina

    Directory of Open Access Journals (Sweden)

    Sanli Deniz

    2011-01-01

    Full Text Available Abstract Superhydrophobic nanoporous anodic aluminum oxide (alumina surfaces were prepared using treatment with vapor-phase hexamethyldisilazane (HMDS. Nanoporous alumina substrates were first made using a two-step anodization process. Subsequently, a repeated modification procedure was employed for efficient incorporation of the terminal methyl groups of HMDS to the alumina surface. Morphology of the surfaces was characterized by scanning electron microscopy, showing hexagonally ordered circular nanopores with approximately 250 nm in diameter and 300 nm of interpore distances. Fourier transform infrared spectroscopy-attenuated total reflectance analysis showed the presence of chemically bound methyl groups on the HMDS-modified nanoporous alumina surfaces. Wetting properties of these surfaces were characterized by measurements of the water contact angle which was found to reach 153.2 ± 2°. The contact angle values on HMDS-modified nanoporous alumina surfaces were found to be significantly larger than the average water contact angle of 82.9 ± 3° on smooth thin film alumina surfaces that underwent the same HMDS modification steps. The difference between the two cases was explained by the Cassie-Baxter theory of rough surface wetting.

  18. NOTE: Fabrication of a gecko-like hierarchical fibril array using a bonded porous alumina template

    Science.gov (United States)

    Suryadi Kustandi, Tanu; Samper, Victor Donald; Ng, Wan Sing; Chong, Ai Shing; Gao, Han

    2007-10-01

    We report a new method to fabricate a hierarchical microfibril array by using bonded porous alumina templates. The fabrication approach extends a powerful and well-established technique of creating porous alumina to create a polymer multilevel structure, mimicking the hierarchical structure of gecko adhesive foot hairs. The nanoporous alumina (pore diameter ≈60 nm; interpore distance ≈100 nm) was generated by the anodization of an aluminum film in an oxalic acid solution. The microporous alumina was produced by exploiting the parallel wafer-scale processing of conventional lithography and anisotropic chemical etching of the thick film of anodic alumina pores. The micro- and nanoporous alumina membranes were subsequently brought into intimate contact and their bonding was accomplished by means of capillary forces and then van der Waals bonding. Hierarchical polymeric microfibrils (fibril diameter ≈10 µm fibril length ≈70 µm) with nanofibril arrays at their tips were obtained after depositing a desired material into the pores and selective etching of the template membranes. The nanofibril has a lateral dimension of approximately 60 nm with length-to-diameter aspect ratios as high as 100:1.

  19. Mask degradation monitoring with aerial mask inspector

    Science.gov (United States)

    Tseng, Wen-Jui; Fu, Yung-Ying; Lu, Shih-Ping; Jiang, Ming-Sian; Lin, Jeffrey; Wu, Clare; Lifschitz, Sivan; Tam, Aviram

    2013-06-01

    As design rule continues to shrink, microlithography is becoming more challenging and the photomasks need to comply with high scanner laser energy, low CDU, and ever more aggressive RETs. This give rise to numerous challenges in the semiconductor wafer fabrication plants. Some of these challenges being contamination (mainly haze and particles), mask pattern degradation (MoSi oxidation, chrome migration, etc.) and pellicle degradation. Fabs are constantly working to establish an efficient methodology to manage these challenges mainly using mask inspection, wafer inspection, SEM review and CD SEMs. Aerial technology offers a unique opportunity to address the above mask related challenges using one tool. The Applied Materials Aera3TM system has the inherent ability to inspect for defects (haze, particles, etc.), and track mask degradation (e.g. CDU). This paper focuses on haze monitoring, which is still a significant challenge in semiconductor manufacturing, and mask degradation effects that are starting to emerge as the next challenge for high volume semiconductor manufacturers. The paper describes Aerial inspector (Aera3) early haze methodology and mask degradation tracking related to high volume manufacturing. These will be demonstrated on memory products. At the end of the paper we take a brief look on subsequent work currently conducted on the more general issue of photo mask degradation monitoring by means of an Aerial inspector.

  20. In-situ electrochemical doping of nanoporous anodic aluminum oxide with indigo carmine organic dye

    Energy Technology Data Exchange (ETDEWEB)

    Stępniowski, Wojciech J., E-mail: wojciech.stepniowski@wat.edu.pl [Department of Advanced Materials and Technology, Faculty of Advanced Technology and Chemistry, Military University of Technology, 2 Kaliskiego Str., 00-908 Warszawa (Poland); Norek, Małgorzata [Department of Advanced Materials and Technology, Faculty of Advanced Technology and Chemistry, Military University of Technology, 2 Kaliskiego Str., 00-908 Warszawa (Poland); Budner, Bogusław [Institute of Optoelectronics, Military University of Technology, 2 Kaliskiego Str., 00-908 Warszawa (Poland); Michalska-Domańska, Marta [Department of Advanced Materials and Technology, Faculty of Advanced Technology and Chemistry, Military University of Technology, 2 Kaliskiego Str., 00-908 Warszawa (Poland); Institute of Optoelectronics, Military University of Technology, 2 Kaliskiego Str., 00-908 Warszawa (Poland); Nowak-Stępniowska, Agata; Bombalska, Aneta; Kaliszewski, Miron [Institute of Optoelectronics, Military University of Technology, 2 Kaliskiego Str., 00-908 Warszawa (Poland); Mostek, Anna [Department of Advanced Materials and Technology, Faculty of Advanced Technology and Chemistry, Military University of Technology, 2 Kaliskiego Str., 00-908 Warszawa (Poland); Thorat, Sanjay; Salerno, Marco [Department of Nanophysics, Istituto Italiano di Tecnologia, via Morego 30, Genova I-16163 (Italy); Giersig, Michael [Institut für Experimentalphysik, Freie Universität Berlin, Arnimallee 14, 14195 Berlin (Germany); Bojar, Zbigniew [Department of Advanced Materials and Technology, Faculty of Advanced Technology and Chemistry, Military University of Technology, 2 Kaliskiego Str., 00-908 Warszawa (Poland)

    2016-01-01

    Nanoporous anodic aluminum oxide was formed in sulfuric acid with addition of indigo carmine. During anodizing, the organic dye was incorporated into the porous oxide walls. X-ray photoelectron spectroscopy revealed the presence of nitrogen and sulfur in the anodic aluminum oxide. Two types of incorporated sulfur were found: belonging to the sulfate anions SO{sub 4}{sup 2−} of the electrolyte and belonging to the C-SO{sub 3}{sup −} side groups of the indigo carmine. Raman spectroscopy confirmed the incorporation and showed that the inorganic–organic hybrid material inherited optical properties from the indigo carmine. Typical modes from pyrrolidone rings, unique for indigo carmine in the investigated system (650 and 1585 cm{sup −1}), were found to be the strongest for the greatest anodizing voltages used. Despite the indigo carmine incorporation, the morphology of the oxide is still nanoporous and its geometry is still tuned by the voltage applied during aluminum anodization. This work presents an inexpensive and facile approach to doping an inorganic oxide material with organic compounds. - Highlights: • Nanoporous anodic alumina was formed in electrolyte with indigo carmine. • XPS confirmed the presence of N and S in anodic alumina. • Raman spectroscopy revealed indigo carmine bands in anodic alumina. • The higher the voltage, the more indigo carmine was incorporated.

  1. Mask industry assessment: 2004

    Science.gov (United States)

    Shelden, Gilbert V.; Hector, Scott D.

    2004-12-01

    Microelectronics industry leaders routinely name mask cost and cycle time as top issues of concern. A survey was created with support from International SEMATECH (ISMT) and administered by SEMI North America to gather information about the mask industry as an objective assessment of its overall condition. The survey is designed with the input of mask technologists from semiconductor manufacturers, merchant mask suppliers, and makers of equipment for mask fabrication. This year's assessment is the third in the current series of annual reports and is intended to be used as a baseline for the mask industry and the microelectronics industry to gain a perspective on the technical and business status of the mask industry. This report will continue to serve as a valuable reference to identify the strengths and opportunities of the mask industry. The results may be used to guide future investments on critical path issues. This year's survey builds upon the 2003 survey to provide an ongoing database using the same questions as a baseline with only a few minor changes or additions. Questions are grouped into categories: general business profile information, data processing, yields and yield loss mechanisms, delivery times, returns and services. Within each category are a many questions that create a detailed profile of both the business and technical status of the mask industry. This assessment includes inputs from ten major global merchant and captive mask manufacturers whose revenue represents approximately 85% of the global mask market.

  2. 2013 mask industry survey

    Science.gov (United States)

    Malloy, Matt

    2013-09-01

    A comprehensive survey was sent to merchant and captive mask shops to gather information about the mask industry as an objective assessment of its overall condition. 2013 marks the 12th consecutive year for this process. Historical topics including general mask profile, mask processing, data and write time, yield and yield loss, delivery times, maintenance, and returns were included and new topics were added. Within each category are multiple questions that result in a detailed profile of both the business and technical status of the mask industry. While each year's survey includes minor updates based on feedback from past years and the need to collect additional data on key topics, the bulk of the survey and reporting structure have remained relatively constant. A series of improvements is being phased in beginning in 2013 to add value to a wider audience, while at the same time retaining the historical content required for trend analyses of the traditional metrics. Additions in 2013 include topics such as top challenges, future concerns, and additional details in key aspects of mask masking, such as the number of masks per mask set per ground rule, minimum mask resolution shipped, and yield by ground rule. These expansions beyond the historical topics are aimed at identifying common issues, gaps, and needs. They will also provide a better understanding of real-life mask requirements and capabilities for comparison to the International Technology Roadmap for Semiconductors (ITRS).

  3. Analyzing EUV mask costs

    Science.gov (United States)

    Lercel, Michael; Kasprowicz, Bryan

    2016-10-01

    The introduction of Extreme Ultraviolet Lithography (EUV) as a replacement for multiple patterning is based on improvements of cycle time, yield, and cost. Earlier cost studies have assumed a simple assumption that EUV masks (being more complex with the multilayer coated blank) are not more than three times as expensive as advanced ArFi (ArF immersion) masks. EUV masks are expected to be more expensive during the ramp of the technology because of the added cost of the complex mask blank, the use of EUV specific mask tools, and a ramp of yield learning relative to the more mature technologies. This study concludes that, within a range of scenarios, the hypothesis that EUV mask costs are not more than three times that of advanced ArFi masks is valid and conservative.

  4. Multifunctional substrates of thin porous alumina for cell biosensors

    KAUST Repository

    Toccafondi, Chiara

    2014-02-27

    We have fabricated anodic porous alumina from thin films (100/500 nm) of aluminium deposited on technological substrates of silicon/glass, and investigated the feasibility of this material as a surface for the development of analytical biosensors aiming to assess the status of living cells. To this goal, porous alumina surfaces with fixed pitch and variable pore size were analyzed for various functionalities. Gold coated (about 25 nm) alumina revealed surface enhanced Raman scattering increasing with the decrease in wall thickness, with factor up to values of approximately 104 with respect to the flat gold surface. Bare porous alumina was employed for micro-patterning and observation via fluorescence images of dye molecules, which demonstrated the surface capability for a drug-loading device. NIH-3T3 fibroblast cells were cultured in vitro and examined after 2 days since seeding, and no significant (P > 0.05) differences in their proliferation were observed on porous and non-porous materials. The effect on cell cultures of pore size in the range of 50–130 nm—with pore pitch of about 250 nm—showed no significant differences in cell viability and similar levels in all cases as on a control substrate. Future work will address combination of all above capabilities into a single device.

  5. An integrated single photon detector array using porous anodic alumina

    NARCIS (Netherlands)

    Melai, J.; Salm, C.; Schmitz, J.; Smits, S.M.; Visschers, J.L.

    2006-01-01

    The aim of the work is fabrication of a photon detector array made using IC compatible wafer-scale post-processing stepts. Plans will be presented to outline these fabrication steps. The detector comprises an integrated Micro-Channel-Plate and an imaging chip like Medipix2. The aim of the work is fa

  6. Calcium aluminate in alumina

    Science.gov (United States)

    Altay, Arzu

    The properties of ceramic materials are determined not only by the composition and structure of the phases present, but also by the distribution of impurities, intergranular films and second phases. The phase distribution and microstructure both depend on the fabrication techniques, the raw materials used, the phase-equilibrium relations, grain growth and sintering processes. In this dissertation research, various approaches have been employed to understand fundamental phenomena such as grain growth, impurity segregation, second-phase formation and crystallization. The materials system chosen was alumina intentionally doped with calcium. Atomic-scale structural analyses of grain boundaries in alumina were carried on the processed samples. It was found that above certain calcium concentrations, CA6 precipitated as a second phase at all sintering temperatures. The results also showed that abnormal grain growth can occur after precipitation and it is not only related to the calcium level, but it is also temperature dependent. In order to understand the formation mechanism of CA6 precipitates in calcium doped alumina samples, several studies have been carried out using either bulk materials or thin films The crystallization of CA2 and CA6 powders has been studied. Chemical processing techniques were used to synthesize the powders. It was observed that CA2 powders crystallized directly, however CA6 powders crystallized through gamma-Al 2O3 solid solution. The results of energy-loss near-edge spectrometry confirmed that gamma-Al2O3 can dissolve calcium. Calcium aluminate/alumina reaction couples have also been investigated. All reaction couples were heat treated following deposition. It was found that gamma-Al2O3 was formed at the interface as a result of the interfacial reaction between the film and the substrate. gamma-Al 2O3 at the interface was stable at much higher temperatures compared to the bulk gamma-Al2O3 formed prior to the CA6 crystallization. In order to

  7. Bauxite Mining and Alumina Refining

    Science.gov (United States)

    Frisch, Neale; Olney, David

    2014-01-01

    Objective: To describe bauxite mining and alumina refining processes and to outline the relevant physical, chemical, biological, ergonomic, and psychosocial health risks. Methods: Review article. Results: The most important risks relate to noise, ergonomics, trauma, and caustic soda splashes of the skin/eyes. Other risks of note relate to fatigue, heat, and solar ultraviolet and for some operations tropical diseases, venomous/dangerous animals, and remote locations. Exposures to bauxite dust, alumina dust, and caustic mist in contemporary best-practice bauxite mining and alumina refining operations have not been demonstrated to be associated with clinically significant decrements in lung function. Exposures to bauxite dust and alumina dust at such operations are also not associated with the incidence of cancer. Conclusions: A range of occupational health risks in bauxite mining and alumina refining require the maintenance of effective control measures. PMID:24806720

  8. Binary Masking & Speech Intelligibility

    DEFF Research Database (Denmark)

    Boldt, Jesper

    The purpose of this thesis is to examine how binary masking can be used to increase intelligibility in situations where hearing impaired listeners have difficulties understanding what is being said. The major part of the experiments carried out in this thesis can be categorized as either experime...... mask using a directional system and a method for correcting errors in the target binary mask. The last part of the thesis, proposes a new method for objective evaluation of speech intelligibility....

  9. Mask industry assessment: 2003

    Science.gov (United States)

    Kimmel, Kurt R.

    2003-12-01

    Microelectronics industry leaders routinely name mask technology and mask supply issues of cost and cycle time as top issues of concern. A survey was initiated in 2002 with support from International SEMATECH (ISMT) and administered by SEMI North America to gather information about the mask industry as an objective assessment of its overall condition.1 This paper presents the results of the second annual survey which is an enhanced version of the inaugural survey building upon its strengths and improving the weak points. The original survey was designed with the input of member company mask technologists, merchant mask suppliers, and industry equipment makers. The assessment is intended to be used as a baseline for the mask industry and the microelectronics industry to gain a perspective on the technical and business status of the critical mask industry. An objective is to create a valuable reference to identify strengths and opportunities and to guide investments on critical-path issues. As subsequent years are added, historical profiles can also be created. This assessment includes inputs from ten major global merchant and captive mask manufacturers representing approximately 80% of the global mask market (using revenue as the measure) and making this the most comprehensive mask industry survey ever. The participating companies are: Compugraphics, Dai Nippon Printing, Dupont Photomask, Hoya, IBM, Infineon, Intel, Taiwan Mask Company, Toppan, and TSMC. Questions are grouped into five categories: General Business Profile Information; Data Processing; Yields and Yield loss Mechanisms; Delivery Time; and Returns and Services. Within each category are a multitude of questions that create a detailed profile of both the business and technical status of the mask industry.

  10. Designing robust alumina nanowires-on-nanopores structures: superhydrophobic surfaces with slippery or sticky water adhesion.

    Science.gov (United States)

    Peng, Shan; Tian, Dong; Miao, Xinrui; Yang, Xiaojun; Deng, Wenli

    2013-11-01

    Hierarchical alumina surfaces with different morphologies were fabricated by a simple one-step anodization method. These alumina films were fabricated by a new raw material: silica gel plate (aluminum foil with a low purity of 97.17%). The modulation of anodizing time enabled the formation of nanowires-on-nanopores hybrid nanostructures having controllable nanowires topographies through a self-assembly process. The resultant structures were demonstrated to be able to achieve superhydrophobicity without any hydrophobic coating layer. More interestingly, it is found that the as-prepared superhydrophobic alumina surfaces exhibited high contrast water adhesion. Hierarchical alumina film with nanowire bunches-on-nanopores (WBOP) morphology presents extremely slippery property which can obtain a sliding angle (SA) as low as 1°, nanowire pyramids-on-nanopores (WPOP) structure shows strongly sticky water adhesion with the adhesive ability to support 15 μL inverted water droplet at most. The obtained superhydrophobic alumina surfaces show remarkable mechanical durability even treated by crimping or pressing without impact on the water-repellent performance. Moreover, the created surfaces also show excellent resistivity to ice water, boiling water, high temperature, organic solvent and oil contamination, which could expand their usefulness and efficacy in harsh conditions.

  11. Binary mask programmable hologram.

    Science.gov (United States)

    Tsang, P W M; Poon, T-C; Zhou, Changhe; Cheung, K W K

    2012-11-19

    We report, for the first time, the concept and generation of a novel Fresnel hologram called the digital binary mask programmable hologram (BMPH). A BMPH is comprised of a static, high resolution binary grating that is overlaid with a lower resolution binary mask. The reconstructed image of the BMPH can be programmed to approximate a target image (including both intensity and depth information) by configuring the pattern of the binary mask with a simple genetic algorithm (SGA). As the low resolution binary mask can be realized with less stringent display technology, our method enables the development of simple and economical holographic video display.

  12. Effects of a magnetic field on growth of porous alumina films on aluminum

    Energy Technology Data Exchange (ETDEWEB)

    Ispas, Adriana; Bund, Andreas [Technische Universitaet Dresden, Physikalische Chemie und Elektrochemie, 01062 Dresden (Germany); Vrublevsky, Igor, E-mail: vrublevsky@bsuir.edu.b [Belarusian State University of Informatics and Radioelectronics Minsk, Department of Micro and Nanoelectronics, 220013 Minsk (Belarus)

    2010-05-01

    The effects induced by a magnetic field on the oxide film growth on aluminum in sulfuric, oxalic, phosphoric and sulfamic acid, and on current transients during re-anodizing of porous alumina films in the barrier-type electrolyte, were studied. Aluminum films of 100 nm thickness were prepared by thermal evaporation on Si wafer substrates. We could show that the duration of the anodizing process increased by 33% during anodizing in sulfuric acid when a magnetic field was applied (0.7 T), compared to the process without a magnetic field. Interestingly, such a magnetic field effect was not found during anodizing in oxalic and sulfamic acid. The pore intervals were decreased by ca. 17% in oxalic acid. These findings were attributed to variations in electronic properties of the anodic oxide films formed in various electrolytes and interpreted on the basis of the influence of trapped electrons on the mobility of ions migrating during the film growth. The spin dependent tunneling of electrons into the surface layer of the oxide under the magnetic field could be responsible for the shifts of the current transients to lower potentials during re-anodizing of heat-treated oxalic and phosphoric acid alumina films.

  13. Gelcasting Polycrystalline Alumina

    Energy Technology Data Exchange (ETDEWEB)

    Janney, M.A.; Zuk, K.J.; Wei, G.C.

    2000-01-01

    OSRAM SYLVANIA INC. is a major U.S. manufacturer of high-intensity lighting. Among its products is the Lumalux TM line of high-pressure sodium vapor arc lamps, which are used for industrial, highway, and street lighting. The key to the performance of these lamps is the polycrystalline alumina (PCA) tube that is used to contain the plasma that is formed in the electric arc. That plasma consists of ionized sodium, mercury, and xenon vapors. The key attributes of the PCA tubes are their transparency ({approximately}97% total transmittance in the visible), their refractoriness (inner wall temperature can reach l2OOC), and their chemical resistance (sodium and mercury vapor are extremely corrosive). The current efficiency of the lamps is very high, up to 100 initial lumens per watt. (Compare incandescent lamps 10-20 lumens per watt, fluorescent lamps 25-90 lumens per watt.)

  14. Influence of anodization parameters on the volume expansion of anodic aluminum oxide formed in mixed solution of phosphoric and oxalic acids

    Science.gov (United States)

    Kao, Tzung-Ta; Chang, Yao-Chung

    2014-01-01

    The growth of anodic alumina oxide was conducted in the mixed solution of phosphoric and oxalic acids. The influence of anodizing voltage, electrolyte temperature, and concentration of phosphoric and oxalic acids on the volume expansion of anodic aluminum oxide has been investigated. Either anodizing parameter is chosen to its full extent of range that allows the anodization process to be conducted without electric breakdown and to explore the highest possible volume expansion factor. The volume expansion factors were found to vary between 1.25 and 1.9 depending on the anodizing parameters. The variation is explained in connection with electric field, ion transport number, temperature effect, concentration, and activity of acids. The formation of anodic porous alumina at anodizing voltage 160 V in 1.1 M phosphoric acid mixed with 0.14 M oxalic acid at 2 °C showed the peak volume expansion factor of 1.9 and the corresponding moderate growth rate of 168 nm/min.

  15. Mask industry assessment: 2005

    Science.gov (United States)

    Shelden, Gilbert; Hector, Scott

    2005-11-01

    Microelectronics industry leaders routinely name mask cost and cycle time as top issues of concern. A survey was created with support from International SEMATECH (ISMT) and administered by SEMI North America to gather information about the mask industry as an objective assessment of its overall condition. The survey is designed with the input of mask technologists from semiconductor manufacturers, merchant mask suppliers, and makers of equipment for mask fabrication. This year's assessment is the fourth in the current series of annual reports and is intended to be used as a baseline for the mask industry and the microelectronics industry to gain a perspective on the technical and business status of the mask industry. This report will continue to serve as a valuable reference to identify the strengths and opportunities of the mask industry. The results may be used to guide future investments on critical path issues. This year's survey contains all of the 2004 survey questions to provide an ongoing database. Additional questions were added to the survey covering operating cost factors and equipment utilization. Questions are grouped into categories: general business profile information, data processing, yields and yield loss mechanisms, delivery times, returns and services, operating cost factors and equipment utilization. Within each category are a many questions that create a detailed profile of both the business and technical status of the mask industry. This assessment includes inputs from eight major global merchant and captive mask manufacturers whose revenue represents approximately 85% of the global mask market. This participation rate is reduced by one captive from 2004. Note: Toppan, DuPont Photomasks Inc and AMTC (new) were consolidated into one input therefore the 2004 and 2005 surveys are basically equivalent.

  16. How the global layout of the mask influences masking strength.

    Science.gov (United States)

    Ghose, Tandra; Hermens, Frouke; Herzog, Michael H

    2012-12-10

    In visual backward masking, the perception of a target is influenced by a trailing mask. Masking is usually explained by local interactions between the target and the mask representations. However, recently it has been shown that the global spatial layout of the mask rather than its local structure determines masking strength (Hermens & Herzog, 2007). Here, we varied the mask layout by spatial, luminance, and temporal cues. We presented a vernier target followed by a mask with 25 elements. Performance deteriorated when the length of the two mask elements neighboring the target vernier was doubled. However, when the length of every second mask element was doubled, performance improved. When the luminance of the neighboring elements was doubled, performance also deteriorated but no improvement in performance was observed when every second element had a double luminance. For temporal manipulations, a complex nonmonotonic masking function was observed. Hence, changes in the mask layout by spatial, luminance, and temporal cues lead to highly different results.

  17. Optical Transmittance of Anodically Oxidized Aluminum Alloy

    Science.gov (United States)

    Saito, Mitsunori; Shiga, Yasunori; Miyagi, Mitsunobu; Wada, Kenji; Ono, Sachiko

    1995-06-01

    Optical transmittance and anisotropy of anodic oxide films that were made from pure aluminum and an aluminum alloy (A5052) were studied. The alloy oxide film exhibits an enhanced polarization function, particularly when anodization is carried out at a large current density. It was revealed by chemical analysis that the alloy oxide film contains a larger amount of unoxidized aluminum than the pure-aluminum oxide film. The polarization function can be elucidated by considering unoxidized aluminum particles that are arranged in the columnar structure of the alumina film. Electron microscope observation showed that many holes exist in the alloy oxide film, around which columnar cells are arranged irregularly. Such holes and irregular cell arrangement cause the increase in the amount of unoxidized aluminum, and consequently induces scattering loss.

  18. Mask Phenomenon in Communication

    Institute of Scientific and Technical Information of China (English)

    郎丽璇

    2013-01-01

    People sometimes wear masks. Abusive expression may be used to convey love while polite words can be exchanged among enemies. This essay describes and discusses this special phenomenon in communication and analyzes the elements that con-tribute to the success of a mask communication.

  19. Alumina-magnesia Refractory Castables

    Institute of Scientific and Technical Information of China (English)

    Wang Jing

    2010-01-01

    @@ 1 Scope This standard specifies the classification,technical requirements,test methods,quality appraisal procedures,packing,marking,transportation,storage,and quality certificate of alumina-magnesia refractory castables.

  20. Stresses in sulfuric acid anodized coatings on aluminum

    Science.gov (United States)

    Alwitt, R. S.; Xu, J.; Mcclung, R. C.

    1993-01-01

    Stresses in porous anodic alumina coatings have been measured for specimens stabilized in air at different temperatures and humidities. In ambient atmosphere the stress is tensile after anodic oxidation and is compressive after sealing. Exposure to dry atmosphere causes the stress to change to strongly tensile, up to 110 MPa. The stress increase is proportional to the loss of water from the coating. These changes are reversible with changes in humidity. Similar reversible effects occur upon moderate temperature changes. The biaxial modulus of the coating is about 100 GPa.

  1. Hybrid mask for deep etching

    KAUST Repository

    Ghoneim, Mohamed T.

    2017-08-10

    Deep reactive ion etching is essential for creating high aspect ratio micro-structures for microelectromechanical systems, sensors and actuators, and emerging flexible electronics. A novel hybrid dual soft/hard mask bilayer may be deposited during semiconductor manufacturing for deep reactive etches. Such a manufacturing process may include depositing a first mask material on a substrate; depositing a second mask material on the first mask material; depositing a third mask material on the second mask material; patterning the third mask material with a pattern corresponding to one or more trenches for transfer to the substrate; transferring the pattern from the third mask material to the second mask material; transferring the pattern from the second mask material to the first mask material; and/or transferring the pattern from the first mask material to the substrate.

  2. Thermochemical Analysis of Molybdenum Thin Films on Porous Alumina.

    Science.gov (United States)

    Lee, Kyoungjin; de Lannoy, Charles-François; Liguori, Simona; Wilcox, Jennifer

    2017-01-12

    Molybdenum (Mo) thin films (thickness thin-film composites were stable below 300 °C but had no reactivity toward gases. Mo thin films showed nitrogen incorporation on the surface as well as in the subsurface at 450 °C, as confirmed by X-ray photoelectron spectroscopy. The reactivity toward nitrogen was diminished in the presence of CO2, although no carbon species were detected either on the surface or in the subsurface. The Mo thin films have a very stable native oxide layer, which may further oxidize to higher oxidation states above 500 °C due to the reaction with the porous anodized alumina substrate. The oxidation of Mo thin films was accelerated in the presence of oxidizing gases. At 600 °C in N2, the Mo thin film on anodized alumina was completely oxidized and may also have been volatilized. The results imply that choosing thermally stable and inactive porous supports and operating in nonoxidizing conditions below 500 °C will likely maintain the stability of the Mo composite. This study provides key information about the chemical and structural stability of a Mo thin film on a porous substrate for future membrane applications and offers further insights into the integrity of thin-film composites when exposed to harsh conditions.

  3. Peltier heats in cryolite melts with alumina

    Energy Technology Data Exchange (ETDEWEB)

    Flem, B.E.; Ratkje, S.K.; Sterten, A. [Univ. of Trondheim (Norway)

    1996-10-01

    The Seebeck coefficient was measured for cells with electrolytes of molten mixtures of sodium fluoride and aluminum fluoride saturated with alumina. The electrodes were either a pair of oxygen electrodes or a pair of aluminum electrodes. For the molar ratio NaF/AlF{sub 3} equal to 1.8, 1.2 and 1.0, the authors obtained the Seebeck coefficients {minus}1.80 mV K{sup {minus}1} at 971 C, {minus}1.63 mV K{sup {minus}1} at 813.6 C and {minus}0.583 mV K{sup {minus}1} at 758 C, respectively, for the oxygen electrodes. For the aluminum electrodes, the authors obtained the Seebeck coefficient {minus}1.23 mV K{sup {minus}1} at 962 C, for the molar ratio NaF/AlF{sub 3} equal to 1.8. The results suggest that there is a substantial reversible heat consumption at the anode during aluminum electrolysis and a large reversible heat production at the cathode. The highest temperature in the Hall-Heroult cell is then closer to the cathode than the anode. The transported entropies of Al{sup 3+} and O{sup 2{minus}} were calculated to be 77 J mol{sup {minus}1} K{sup {minus}1} and 10 J mol{sup {minus}1} K{sup {minus}1}, respectively, when the molar ratio NaF/AlF{sub 3} was equal to 1.0.

  4. Hemispherical Shell Nanostructures from Metal-Stripped Embossed Alumina on Aluminum Templates

    DEFF Research Database (Denmark)

    Nielsen, Peter; Albrektsen, Ole; Simonsen, Adam Cohen

    2011-01-01

    aluminum/ alumina (Al/Al2O3) templates as a novel and versatile nanofabrication procedure, and we demonstrate explicitly how to exploit the technique for developing large-area hexagonally close-packed hemispherical shell nanostructures by stripping noble metal layers from embossed templates fabricated from...... anodized Al. Utilizing for this process the linear relationship between anodization voltage and the resulting interpore distance in the formed oxide, it is possible to tune the radius of curvature of the resulting hemispherical shells continuously, which in turn results in tunable optical properties...

  5. Photoluminescent behavior of heat-treated porous alumina films formed in malonic acid

    Energy Technology Data Exchange (ETDEWEB)

    Vrublevsky, I., E-mail: vrublevsky@bsuir.edu.by [Department of Micro and Nanoelectronics, Belarusian State University of Informatics and Radioelectronics, 6 Brovka str, Minsk 220013 (Belarus); Jagminas, A. [Institute of Chemistry, A.Gostauto 9, LT-01108 Vilnius (Lithuania); Hemeltjen, S.; Goedel, W.A. [Institut fuer Chemie, Technische Universitaet Chemnitz, D-09107 (Germany)

    2010-01-15

    In the present work IR spectroscopy, electron probe microanalysis (EPMA) and photoluminescence (PL) spectral measurements were applied to study the effect of treatment temperature (T) on compositional and luminescent properties of malonic acid alumina films. Our studies have shown that the heat treatment of anodic alumina films at investigated temperatures from 100 up to 700 deg. C changes their photoluminescence spectra considerably. An increase in T results in the PL intensity growth. When reaching its maximum at 600 deg. C the luminescence intensity then decreases drastically with further T growth. The films heat-treated at 500 and 600 deg. C demonstrate asymmetrical PL band with Gaussian peaks at 437 and 502 nm. We proved that the malonic acid species incorporated into the alumina bulk during the film formation are responsible for photoluminescence band with its peak at 437 nm.

  6. Superior thermal conductivity of transparent polymer nanocomposites with a crystallized alumina membrane

    Directory of Open Access Journals (Sweden)

    Md. Poostforush

    2014-04-01

    Full Text Available The properties of novel thermoconductive and optically transparent nanocomposites have been reported. The composites were prepared by the impregnation of thermoset resin into crystallized anodic aluminum oxide (AAO. Crystallized AAO synthesized by annealing amorphous AAO membrane at 1200°C. Although through-plane thermal conductivity of nanocomposites improved up to 1.13 W•m–1•K–1 (39 vol% alumina but their transparency was preserved (Tλ550 nm ~ 72%. Integrated annealed alumina phase, low refractive index mismatch between resin and alumina and formation of nano-optical fibers through the membrane resulted in such marvel combination. This report shows a great potential of these types of nanocomposites in ‘heat management’ of lightening devices.

  7. Advances in aluminum anodizing

    Science.gov (United States)

    Dale, K. H.

    1969-01-01

    White anodize is applied to aluminum alloy surfaces by specific surface preparation, anodizing, pigmentation, and sealing techniques. The development techniques resulted in alloys, which are used in space vehicles, with good reflectance values and excellent corrosive resistance.

  8. Gilded Silver Mask

    Institute of Scientific and Technical Information of China (English)

    1998-01-01

    This gilded silver mask from the Liao Dynasty is 31 cm long and 22.2 cm wide. The plump oval face was designed with a protruding brow ridge, narrow eyes, high-bridged nose and closed mouth. The chin is slightly round against a thin neck, the ears are long and the hair can be clearly seen from the finely carved lines. The use of masks was recorded as

  9. Zinc anode alloy for sacrificial anodes

    Energy Technology Data Exchange (ETDEWEB)

    Jore, T.N.

    1984-02-13

    A zinc anode for sacrifical anodes, for preventing intercrystalline corrosion, comprises 0.10-050% by weight Al, 0.025-1.15% by weight Cd, and the remainder zinc and impurities caused by the production method, wherein the alloy also contains 0.01-1.0% magnesium.

  10. New mask technology challenges

    Science.gov (United States)

    Kimmel, Kurt R.

    2001-09-01

    Mask technology development has accelerated dramatically in recent years from the glacial pace of the last three decades to the rapid and sometimes simultaneous introductions of new wavelengths and mask-based resolution enhancement techniques. The nature of the semiconductor business has also become one driven by time-to-market as an overwhelming factor in capturing market share and profit. These are among the factors that have created enormous stress on the mask industry to produce masks with enhanced capabilities, such as phase-shifting attenuators, sub-resolution assist bars, and optical proximity correction (OPC) features, while maintaining or reducing cost and cycle time. The mask can no longer be considered a commodity item that is purchased form the lowest-cost supplier. Instead, it must now be promoted as an integral part of the technical and business case for a total lithographic solution. Improving partnership between designer, mask-maker, and wafer lithographer will be the harbinger of success in finding a profitable balance of capability, cost, and cycle time. Likewise for equipment infrastructure development, stronger partnership on the international level is necessary to control development cost and mitigate schedule and technical risks.

  11. Gelcasting polycrystalline alumina

    Energy Technology Data Exchange (ETDEWEB)

    Janney, M.A. [Oak Ridge National Lab., TN (United States)

    1997-04-01

    This work is being done as part of a CRADA with Osram-Sylvania, Inc. (OSI) OSI is a major U.S. manufacturer of high-intensity lighting. Among its products is the Lumalux{reg_sign} line of high-pressure sodium vapor arc lamps, which are used for industrial, highway, and street lighting. The key to the performance of these lamps is the polycrystalline alumina (PCA) tube that is used to contain the plasma that is formed in the electric arc. That plasma consists of ionized sodium, mercury, and xenon vapors. The key attributes of the PCA tubes are their transparency (95% total transmittance in the visible region), their refractoriness (inner wall temperature can reach 1400{degrees}C), and their chemical resistance (sodium and mercury vapor are extremely corrosive). The current efficiency of the lamps is very high, on the order of several hundred lumens / watt. (Compare - incandescent lamps -13 lumens/watt fluorescent lamps -30 lumens/watt.) Osram-Sylvania would like to explore using gelcasting to form PCA tubes for Lumalux{reg_sign} lamps, and eventually for metal halide lamps (known as quartz-halogen lamps). Osram-Sylvania, Inc. currently manufactures PCA tubes by isostatic pressing. This process works well for the shapes that they presently use. However, there are several types of tubes that are either difficult or impossible to make by isostatic pressing. It is the desire to make these new shapes and sizes of tubes that has prompted Osram-Sylvania`s interest in gelcasting. The purpose of the CRADA is to determine the feasibility of making PCA items having sufficient optical quality that they are useful in lighting applications using gelcasting.

  12. Mirror-backed Dark Alumina: A Nearly Perfect Absorber for Thermoelectronics and Thermophotovotaics

    KAUST Repository

    Farhat, Mohamed

    2016-01-28

    We present here a broadband, wide-angle, and polarization-independent nearly perfect absorber consisting of mirror-backed nanoporous alumina. By electrochemically anodizing the disordered multicomponent aluminum and properly tailoring the thickness and air-filling fraction of nanoporous alumina, according to the Maxwell-Garnet mixture theory, a large-area dark alumina can be made with excellent photothermal properties and absorption larger than 93% over a wide wavelength range spanning from near-infrared to ultraviolet light, i.e. 250 nm–2500 nm. The measured absorption is orders of magnitude greater than other reported anodized porous alumina, typically semi-transparent at similar wavelengths. This simple yet effective approach, however, does not require any lithography, nano-mixture deposition, pre- and post-treatment. Here, we also envisage and theoretically investigate the practical use of proposed absorbers and/or photothermal converters in integrated thermoelectronic and/or thermophotovoltaic energy conversion devices, which make efficient use of the entire spectrum of ambient visible to near-infrared radiation.

  13. Imprinting nanoporous alumina patterns into the magneto-transport of oxide superconductors.

    Science.gov (United States)

    Villegas, J E; Swiecicki, I; Bernard, R; Crassous, A; Briatico, J; Wolf, T; Bergeal, N; Lesueur, J; Ulysse, C; Faini, G; Hallet, X; Piraux, L

    2011-02-18

    We used oxygen ion irradiation to transfer the nanoscale pattern of a porous alumina mask into high-T(C) superconducting thin films. This causes a nanoscale spatial modulation of superconductivity and strongly affects the magneto-transport below T(C), which shows a series of periodic oscillations reminiscent of the Little-Parks effect in superconducting wire networks. This irradiation technique could be extended to other oxide materials in order to induce ordered nanoscale phase segregation.

  14. Mask Blank Defect Detection

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, M A; Sommargren, G E

    2000-02-04

    Mask blanks are the substrates that hold the master patterns for integrated circuits. Integrated circuits are semiconductor devices, such as microprocessors (mPs), dynamic random access memory (DRAMs), and application specific integrated circuits (ASICs) that are central to the computer, communication, and electronics industries. These devices are fabricated using a set of master patterns that are sequentially imaged onto light-sensitive coated silicon wafers and processed to form thin layers of insulating and conductive materials on top of the wafer. These materials form electrical paths and transistors that control the flow of electricity through the device. For the past forty years the semiconductor industry has made phenomenal improvements in device functionality, compactness, speed, power, and cost. This progress is principally due to the exponential decrease in the minimum feature size of integrated circuits, which has been reduced by a factor of {radical}2 every three years. Since 1992 the Semiconductor Industry Association (SIA) has coordinated the efforts of producing a technology roadmap for semiconductors. In the latest document, ''The International Technology Roadmap for Semiconductors: 1999'', future technology nodes (minimum feature sizes) and targeted dates were specified and are summarized in Table 1. Lithography is the imaging technology for producing a de-magnified image of the mask on the wafer. A typical de-magnification factor is 4. Mask blank defects as small as one-eighth the equivalent minimum feature size are printable and may cause device failure. Defects might be the result of the surface preparation, such as polishing, or contamination due to handling or the environment. Table 2 shows the maximum tolerable defect sizes on the mask blank for each technology node. This downward trend puts a tremendous burden on mask fabrication, particularly in the area of defect detection and reduction. A new infrastructure for mask

  15. Transport properties of alumina nanofluids

    Energy Technology Data Exchange (ETDEWEB)

    Wong, Kau-Fui Vincent; Kurma, Tarun [Department of Mechanical and Aerospace Engineering, University of Miami, Coral Gables, FL 33124 (United States)], E-mail: kwong@miami.edu

    2008-08-27

    Recent studies have showed that nanofluids have significantly greater thermal conductivity compared to their base fluids. Large surface area to volume ratio and certain effects of Brownian motion of nanoparticles are believed to be the main factors for the significant increase in the thermal conductivity of nanofluids. In this paper all three transport properties, namely thermal conductivity, electrical conductivity and viscosity, were studied for alumina nanofluid (aluminum oxide nanoparticles in water). Experiments were performed both as a function of volumetric concentration (3-8%) and temperature (2-50 deg. C). Alumina nanoparticles with a mean diameter of 36 nm were dispersed in water. The effect of particle size was not studied. The transient hot wire method as described by Nagaska and Nagashima for electrically conducting fluids was used to test the thermal conductivity. In this work, an insulated platinum wire of 0.003 inch diameter was used. Initial calibration was performed using de-ionized water and the resulting data was within 2.5% of standard thermal conductivity values for water. The thermal conductivity of alumina nanofluid increased with both increase in temperature and concentration. A maximum thermal conductivity of 0.7351 W m{sup -1} K{sup -1} was recorded for an 8.47% volume concentration of alumina nanoparticles at 46.6 deg. C. The effective thermal conductivity at this concentration and temperature was observed to be 1.1501, which translates to an increase in thermal conductivity by 22% when compared to water at room temperature. Alumina being a good conductor of electricity, alumina nanofluid displays an increasing trend in electrical conductivity as volumetric concentration increases. A microprocessor-based conductivity/TDS meter was used to perform the electrical conductivity experiments. After carefully calibrating the conductivity meter's glass probe with platinum tip, using a standard potassium chloride solution, readings were

  16. Transport properties of alumina nanofluids.

    Science.gov (United States)

    Wong, Kau-Fui Vincent; Kurma, Tarun

    2008-08-27

    Recent studies have showed that nanofluids have significantly greater thermal conductivity compared to their base fluids. Large surface area to volume ratio and certain effects of Brownian motion of nanoparticles are believed to be the main factors for the significant increase in the thermal conductivity of nanofluids. In this paper all three transport properties, namely thermal conductivity, electrical conductivity and viscosity, were studied for alumina nanofluid (aluminum oxide nanoparticles in water). Experiments were performed both as a function of volumetric concentration (3-8%) and temperature (2-50 °C). Alumina nanoparticles with a mean diameter of 36 nm were dispersed in water. The effect of particle size was not studied. The transient hot wire method as described by Nagaska and Nagashima for electrically conducting fluids was used to test the thermal conductivity. In this work, an insulated platinum wire of 0.003 inch diameter was used. Initial calibration was performed using de-ionized water and the resulting data was within 2.5% of standard thermal conductivity values for water. The thermal conductivity of alumina nanofluid increased with both increase in temperature and concentration. A maximum thermal conductivity of 0.7351 W m(-1) K(-1) was recorded for an 8.47% volume concentration of alumina nanoparticles at 46.6 °C. The effective thermal conductivity at this concentration and temperature was observed to be 1.1501, which translates to an increase in thermal conductivity by 22% when compared to water at room temperature. Alumina being a good conductor of electricity, alumina nanofluid displays an increasing trend in electrical conductivity as volumetric concentration increases. A microprocessor-based conductivity/TDS meter was used to perform the electrical conductivity experiments. After carefully calibrating the conductivity meter's glass probe with platinum tip, using a standard potassium chloride solution, readings were taken at

  17. Overview of Mask Metrology

    Science.gov (United States)

    Rice, Bryan J.; Jindal, Vibhu; Lin, C. C.; Harris-Jones, Jenah; Kwon, Hyuk Joo; Ma, Hsing-Chien; Goldstein, Michael; Chan, Yau-Wai; Goodwin, Frank

    2011-11-01

    Extreme ultraviolet (EUV) lithography is the successor to optical lithography and will enable advanced patterning in semiconductor manufacturing processes down to the 8 nm half pitch technology node and beyond. However, before EUV can successfully be inserted into high volume manufacturing a few challenges must be overcome. Central among these remaining challenges is the requirement to produce "defect free" EUV masks. Mask blank defects have been one of the top challenges in the commercialization of extreme ultraviolet (EUV) lithography. To determine defect sources and devise mitigation solutions, detailed characterization of defects is critical. However, small defects pose challenges in metrology scale-up. SEMATECH has a comprehensive metrology strategy to address any defect larger than a 20 nm core size to obtain solutions for defect-free EUV mask blanks. SEMATECH's Mask Blank Development Center has been working since 2003 to develop the technology to support defect free EUV mask blanks. Since 2003, EUV mask blank defects have been reduced from 10000 of size greater than 100 nm to about a few tens at size 70 nm. Unfortunately, today's state of the art defect levels are still about 10 to 100 times higher than needed. Closing this gap requires progress in the various processes associated with glass substrate creation and multilayer deposition. That process development improvement in turn relies upon the availability of metrology equipment that can resolve and chemically characterize defects as small as 30 nm. The current defect reduction efforts at SEMATECH have intensively included a focus on inspection and characterization. The facility boasts nearly 100M of metrology hardware, including an FEI Titan TEM, Lasertec M1350 and M7360 tools, an actinic inspection tool, AFM, SPM, and scanning auger capabilities. The newly established Auger tool at SEMATECH can run a standard 6-inch mask blank and is already providing important information on sub-100 nm defects on EUV

  18. [The laryngeal mask].

    Science.gov (United States)

    Poltroniéri, J

    1990-01-01

    A new type of airway has been widely used for two years, throughout hospitals in the United Kingdom. Designed and created since 1983 by Dr AIJ Brain, the Laryngeal Mask Airway (LMA) is a compromise between the endotracheal tube and the face-mask. Blindly inserted in an anaesthetized patient, without either a laryngoscope or neuromuscular blockade, it provides a good airway in almost all cases. It is often able to offer an effective alternative to difficult intubation. The LMA can be used with either spontaneous or positive pressure ventilation. Because it doesn't provide a reliable protection of the airway from aspiration, it should never be used in the patient with a full stomach. The spontaneously breathing patient, undergoing elective surgery for 15 to 60 minutes, in supine position, who would ordinarily be managed with a face-mask is the more likely candidate for the LMA. But, longer procedures, in lateral or prone position, with controlled ventilation can usually be carried out using the Brain's device. More effective and less demanding than the facial-mask, much less hurtful than the endotracheal tube, the Laryngeal Mask is potentially an important and valuable addition to anaesthetic care.

  19. Orion Emergency Mask Approach

    Science.gov (United States)

    Tuan, George C.; Graf, John C.

    2009-01-01

    Emergency mask approach on Orion poses a challenge to the traditional Shuttle or Station approaches. Currently, in the case of a fire or toxic spill event, the crew utilizes open loop oxygen masks that provide the crew with oxygen to breath, but also dumps the exhaled oxygen into the cabin. For Orion, with a small cabin volume, the extra oxygen will exceed the flammability limit within a short period of time, unless a nitrogen purge is also provided. Another approach to a fire or toxic spill event is the use of a filtering emergency masks. These masks utilize some form of chemical beds to scrub the air clean of toxic providing the crew safe breathing air for a period without elevating the oxygen level in the cabin. Using the masks and a form of smoke-eater filter, it may be possible to clean the cabin completely or to a level for safe transition to a space suit to perform a cabin purge. Issues with filters in the past have been the reaction time, breakthroughs, and high breathing resistance. Development in a new form of chemical filters has shown promise to make the filtering approach feasible.

  20. New roots to formation of nanostructures on glass surface through anodic oxidation of sputtered aluminum

    Directory of Open Access Journals (Sweden)

    Satoru Inoue, Song-Zhu Chu, Kenji Wada, Di Li and Hajime Haneda

    2003-01-01

    Full Text Available New processes for the preparation of nanostructure on glass surfaces have been developed through anodic oxidation of sputtered aluminum. Aluminum thin film sputtered on a tin doped indium oxide (ITO thin film on a glass surface was converted into alumina by anodic oxidation. The anodic alumina gave nanometer size pore array standing vertically on the glass surface. Kinds of acids used in the anodic oxidation changed the pore size drastically. The employment of phosphoric acid solution gave several tens nanometer size pores. Oxalic acid cases produced a few tens nanometer size pores and sulfuric acid solution provided a few nanometer size pores. The number of pores in a unit area could be changed with varying the applied voltage in the anodization and the pore sizes could be increased by phosphoric acid etching. The specimen consisting of a glass substrate with the alumina nanostructures on the surface could transmit UV and visible light. An etched specimen was dipped in a TiO2 sol solution, resulting in the impregnation of TiO2 sol into the pores of alumina layer. The TiO2 sol was heated at ~400 °C for 2 h, converting into anatase phase TiO2. The specimens possessing TiO2 film on the pore wall were transparent to the light in UV–Visible region. The electro deposition technique was applied to the introduction of Ni metal into pores, giving Ni nanorod array on the glass surface. The removal of the barrier layer alumina at the bottom of the pores was necessary to attain smooth electro deposition of Ni. The photo catalytic function of the specimens possessing TiO2 nanotube array was investigated in the decomposition of acetaldehyde gas under the irradiation of UV light, showing that the rate of the decomposition was quite large.

  1. Rf glow discharge optical emission spectrometry for the analysis of arrays of Ni nanowires in nanoporous alumina and titania membranes

    Energy Technology Data Exchange (ETDEWEB)

    Prida, V.M.; Bordel, N.; Hernando, B. [Depto. Fisica, Universidad Oviedo, Calvo Sotelo s/n, 33007 Oviedo (Spain); Navas, D.; Pirota, K.R.; Vazquez, M. [Instituto de Ciencia de Materiales de Madrid (CSIC), Cantoblanco, 28049 Madrid (Spain); Hernandez-Velez, M. [Instituto de Ciencia de Materiales de Madrid (CSIC), Cantoblanco, 28049 Madrid (Spain); Depto. Fisica Aplicada, C-XII, Universidad Autonoma Madrid, Cantoblanco, 28049 Madrid (Spain); Menendez, A.; Pereiro, R.; Sanz-Medel, A. [Depto. Quimica Fisica y Analitica, Facultad de Quimica, Julian Claveria 8, 33006 Oviedo (Spain)

    2006-05-15

    Anodic alumina (Al{sub 2}O{sub 3}) and titania (TiO{sub 2}) nanoporous oxide membranes are among the most widely studied self-organized nanopore templates, formed by uniform and well aligned arrays of synthetized nanometric pores or tubes. Here, we perform a comparative study of the depth profiling analysis in self-ordered alumina and titania nanoporous membrane templates by means of the radiofrequency glow discharge coupled to optical emission spectrometry (rf-GD-OES) technique. The densely packed columnar arrays of hexagonally self-ordered nanoporous alumina membranes investigated, with an average inner pore diameter of 35 nm and 105 nm interspacing, give an uniform thickness pore length about more than 5 {mu}m, depending on the anodization time. Meanwhile, the analysis of the anodized titania nanotubes, with an average inner pore diameter of 100 nm and 40 nm wall thickness, shown to be about 300 nm in length. Each type of membranes were also studied in both cases, when the nanopores were empty and after filling with electrodeposited Ni. The direct analysis by rf-GD-OES reveals the ability of this technique to control the quality of these so synthesized nanocomposites formed by electrodeposited Ni nanowires into the alumina and titania nanoporous templates. (copyright 2006 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  2. Rf glow discharge optical emission spectrometry for the analysis of arrays of Ni nanowires in nanoporous alumina and titania membranes

    Science.gov (United States)

    Prida, V. M.; Navas, D.; Pirota, K. R.; Hernandez-Velez, M.; Menéndez, A.; Bordel, N.; Pereiro, R.; Sanz-Medel, A.; Hernando, B.; Vazquez, M.

    2006-05-01

    Anodic alumina (Al2O3) and titania (TiO2) nanoporous oxide membranes are among the most widely studied self-organized nanopore templates, formed by uniform and well aligned arrays of synthetized nanometric pores or tubes. Here, we perform a comparative study of the depth profiling analysis in self-ordered alumina and titania nanoporous membrane templates by means of the radiofrequency glow discharge coupled to optical emission spectrometry (rf-GD-OES) technique. The densely packed columnar arrays of hexagonally self-ordered nanoporous alumina membranes investigated, with an average inner pore diameter of 35 nm and 105 nm interspacing, give an uniform thickness pore length about more than 5 μm, depending on the anodization time. Meanwhile, the analysis of the anodized titania nanotubes, with an average inner pore diameter of 100 nm and 40 nm wall thickness, shown to be about 300 nm in length. Each type of membranes were also studied in both cases, when the nanopores were empty and after filling with electrodeposited Ni. The direct analysis by rf-GD-OES reveals the ability of this technique to control the quality of these so synthesized nanocomposites formed by electrodeposited Ni nanowires into the alumina and titania nanoporous templates.

  3. Alumina Coating on Carbon Fibers by Sol-Gel Method

    OpenAIRE

    2006-01-01

    Alumina precursor film was coated on carbon fibers by a sol-gel method using aluminum alkoxide solution. The optimum coating condition for the concentration of alumina alkoxide and silane coupling agent was determined to uniformly coat alumina precursor on carbon fibers. Alumina precursor converted to alumina ceramics by heating at 750℃. SEM and EPMA showed that alumina ceramics was uniformly coated on carbon fibers. The thickness of alumina layer increased with increasing coating times. The ...

  4. COAs: Behind the Masks.

    Science.gov (United States)

    Birke, Szifra

    1993-01-01

    Provides information on alcoholism and codependency to help teachers identify and respond to children of alcoholics (COAs). Discusses characteristics of alcoholic homes and problems encountered by children and adult COAs. Examines survival "masks" of COAs, including hero, rebel, adjustor, clown, and caretaker. Lists organizational,…

  5. COAs: Behind the Masks.

    Science.gov (United States)

    Birke, Szifra

    1993-01-01

    Provides information on alcoholism and codependency to help teachers identify and respond to children of alcoholics (COAs). Discusses characteristics of alcoholic homes and problems encountered by children and adult COAs. Examines survival "masks" of COAs, including hero, rebel, adjustor, clown, and caretaker. Lists organizational,…

  6. Masked mycotoxins: a review.

    Science.gov (United States)

    Berthiller, Franz; Crews, Colin; Dall'Asta, Chiara; Saeger, Sarah De; Haesaert, Geert; Karlovsky, Petr; Oswald, Isabelle P; Seefelder, Walburga; Speijers, Gerrit; Stroka, Joerg

    2013-01-01

    The aim of this review is to give a comprehensive overview of the current knowledge on plant metabolites of mycotoxins, also called masked mycotoxins. Mycotoxins are secondary fungal metabolites, toxic to human and animals. Toxigenic fungi often grow on edible plants, thus contaminating food and feed. Plants, as living organisms, can alter the chemical structure of mycotoxins as part of their defence against xenobiotics. The extractable conjugated or non-extractable bound mycotoxins formed remain present in the plant tissue but are currently neither routinely screened for in food nor regulated by legislation, thus they may be considered masked. Fusarium mycotoxins (deoxynivalenol, zearalenone, fumonisins, nivalenol, fusarenon-X, T-2 toxin, HT-2 toxin, fusaric acid) are prone to metabolisation or binding by plants, but transformation of other mycotoxins by plants (ochratoxin A, patulin, destruxins) has also been described. Toxicological data are scarce, but several studies highlight the potential threat to consumer safety from these substances. In particular, the possible hydrolysis of masked mycotoxins back to their toxic parents during mammalian digestion raises concerns. Dedicated chapters of this article address plant metabolism as well as the occurrence of masked mycotoxins in food, analytical aspects for their determination, toxicology and their impact on stakeholders.

  7. Processing and Performance of Alumina Fiber Reinforced Alumina Composites

    Institute of Scientific and Technical Information of China (English)

    P.Y.Lee; T.Uchijima; T.Yano

    2003-01-01

    Processing of alumina fiber-reinforced alumina matrix composites by hot-pressing was described. The mechanical properties of the composites fabricated by different sintering conditions including temperature and pressure have been investigated. The results indicated that the higher sintering temperature and pressure corresponded to the higher bulk density and higher maximum strength of the composite, whereas the pseudo-ductility of the composite was lower. The preliminary results of the composite with monazite-coated fibers showed that maximum strength could be improved up to 35% compared with the noncoated fiber composite in the same sintering condition. Moreover, the fracture behavior of the composite changed from completely brittle fracture to non-brittle fracture under the suitable sintering conditions. SEM observation of the fracture surface indicated that the coating worked as a protective barrier and avoided sintering of the fibers together even at high temperature and pressure during densification process.

  8. CADAT integrated circuit mask analysis

    Science.gov (United States)

    1981-01-01

    CADAT System Mask Analysis Program (MAPS2) is automated software tool for analyzing integrated-circuit mask design. Included in MAPS2 functions are artwork verification, device identification, nodal analysis, capacitance calculation, and logic equation generation.

  9. Sintering behaviour of spinel–alumina composites

    Indian Academy of Sciences (India)

    Soumen Pal; A K Bandyopadhyay; P G Pal; S Mukherjee; B N Samaddar

    2009-04-01

    Study of alumina–magnesia binary phase diagram reveals that around 40–50 wt% alumina dissolves in spinel (MgAl2O4) at 1600°C. Solid solubility of alumina in spinel decreases rapidly with decreasing temperature, which causes exsolution of alumina from spinel phase. Previous work of one of the authors revealed that the exsolution of alumina makes some interlocking structures in between alumina and spinel phases. In the present investigation, refractory grade calcined alumina and spinel powder were used to make different batch compositions. Green pellets, formed at a pressure of 1550 kg cm-2 were fired at different temperatures of 1500°, 1550° and 1600°C for 2 h soaking time. Bulk density, percent apparent porosity, firing shrinkage etc were measured at each temperature. Sintering results were analysed to understand the mechanism of spinel–alumina interactions. SEM study of present samples does not reveal the distinct precipitation of needle shaped -alumina from spinel, but has some effect on densification process of spinel–alumina composites. Microstructural differences between present and previous work suggest an ample scope of further work in spinel–alumina composites.

  10. Sodium-Beta Alumina Batteries: Status and Challenges

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Xiaochuan; Lemmon, John P.; Sprenkle, Vincent L.; Yang, Zhenguo

    2010-09-05

    Sodium-beta alumina batteries, have been extensively developed for a few decades and encouraging progress has been achieved so far. The anode is typically molten sodium while the cathode can be molten sulfur (Na-S battery) or solid transition metal halides plus a liquid phase secondary electrolyte (e.g., ZEBRA battery). The electrolyte typically used is a β"-Al2O3 solid membrane. The issues prohibiting broad commercialization of this type of technology are dependent on the materials used, but can be broadly described as relatively high cost, safety (particularly for the Na-S couple), and low power. This paper offers a review on materials and designs for the batteries and discusses the challenges ahead for further technology improvement.

  11. Wettability of Aluminum on Alumina

    Science.gov (United States)

    Bao, Sarina; Tang, Kai; Kvithyld, Anne; Tangstad, Merete; Engh, Thorvald Abel

    2011-12-01

    The wettability of molten aluminum on solid alumina substrate has been investigated by the sessile drop technique in a 10-8 bar vacuum or under argon atmosphere in the temperature range from 1273 K to 1673 K (1000 °C to 1400 °C). It is shown that the reduction of oxide skin on molten aluminum is slow under normal pressures even with ultralow oxygen potential, but it is enhanced in high vacuum. To describe the wetting behavior of the Al-Al2O3 system at lower temperatures, a semiempirical calculation was employed. The calculated contact angle at 973 K (700 °C) is approximately 97 deg, which indicates that aluminum does not wet alumina at aluminum casting temperatures. Thus, a priming height is required for aluminum to infiltrate a filter. Wetting in the Al-Al2O3 system increases with temperature.

  12. The VIRMOS mask manufacturing tools; 2, Mask manufacturing and handling

    CERN Document Server

    Conti, G; Mattaini, E; MacCagni, D; Lefèvre, O; Saisse, M; Vettolani, G

    1999-01-01

    We describe the VIRMOS Mask Manufacturing Unit (MMU) configuration, composed of two units:the Mask Manufacturing Machine (with its Control Unit) and the Mask Handling Unit (inclusive of Control Unit, Storage Cabinets and robot for loading of the Instrument Cabinets). For both VIMOS and NIRMOS instruments, on the basis of orders received by the Mask Preparation Software (see paper (a) in same proceedings), the function of the MMU is to perform an off-line mask cutting and identification, followed by mask storing and subsequent filling of the Instrument Cabinets (IC). We describe the characteristics of the LPKF laser cutting machine and the work done to support the choice of this equipment. We also describe the remaining of the hardware configuration and the Mask Handling Software.

  13. Effect of impregnation phases on the performance of Ni-based anodes for low temperature solid oxide fuel cells

    Science.gov (United States)

    Liu, Zhangbo; Ding, Dong; Liu, Beibei; Guo, Weiwei; Wang, Wendong; Xia, Changrong

    2011-10-01

    Impregnated nanoparticles are very effective in improving the electrochemical performance of solid oxide fuel cell (SOFC) anodes possibly due to the extension of reaction sites and/or the enhancement of catalytic activity. In this work, samaria-doped ceria (SDC), pure ceria, samaria, and alumina oxides impregnated Ni-based anodes are fabricated to compare the site extending and the catalytic effects. Except for alumina, the impregnation of the other three nano-sized oxides could substantially enhance the performance of the anodes for the hydrogen oxidation reactions. Moreover, single cells with CeO2 and Sm2O3 impregnated anodes could exhibit as great performance as those with SDC impregnated anodes. When the impregnation loading reached the optimal value, 1.7 mmol cm-3, these cells exhibit very high performance, with peak power densities around 750 mW cm-2. The high performance of CeO2 and Sm2O3 impregnated anodes demonstrates that the improved performance are mainly attributed to the significantly improved electrochemical activities of the anodes, but not to the extension of triple-phase-boundary, and wet impregnation is indeed an alternative and effective technique to introduce these nano-sized catalytic active oxides into the anode configuration of SOFCs to enhance cell performance, stability and reliability.

  14. Structure of anodized Al–Zr sputter deposited coatings and effect on optical appearance

    Energy Technology Data Exchange (ETDEWEB)

    Gudla, Visweswara Chakravarthy [Department of Mechanical Engineering, Technical University of Denmark, DK-2800 Kgs. Lyngby (Denmark); Canulescu, Stela [Department of Photonics Engineering, Technical University of Denmark, DK-4000 Roskilde (Denmark); Shabadi, Rajashekhara [Unité Matériaux et Transformations, Université Lille1, 59655 Villeneuve ‘Ascq (France); Rechendorff, Kristian [Tribology Centre, Danish Technological Institute, DK-8000 Århus C (Denmark); Dirscherl, Kai [Danish Fundamental Metrology, DK-2800 Kgs., Lyngby (Denmark); Ambat, Rajan, E-mail: ram@mek.dtu.dk [Department of Mechanical Engineering, Technical University of Denmark, DK-2800 Kgs. Lyngby (Denmark)

    2014-10-30

    Highlights: • Microstructure of magnetron sputtered Al–Zr coatings on AA6060 under as coated and heat treated condition. • Effect of heat treatment and precipitation of Al–Zr–Si (τ{sub 1}) phase on optical appearance of anodized layer. • Partial oxidation of τ{sub 1} precipitates after anodizing and relation to darkening of the anodized layer. • Oxidized region of τ{sub 1} precipitates was amorphous while unoxidized region retained crystallinity. • Unoxidized metallic τ{sub 1} in amorphous anodic alumina acts as light absorption centres and causes darkening after anodizing. - Abstract: The mechanism of interaction of light with the microstructure of anodized layer giving specific optical appearance is investigated using Al–Zr sputter deposited coating as a model system on an AA6060 substrate. Differences in the oxidative nature of various microstructural components result in the evolution of typical features in the anodized layer, which are investigated as a function of microstructure and correlated with its optical appearance. The Zr concentration in the coating was varied from 6 wt.% to 23 wt.%. Heat treatment of the coated samples was carried out at 550 °C for 4 h in order to evolve Al–Zr based second phase precipitates in the microstructure. Anodizing was performed using 20 wt.% sulphuric acid at 18 °C with an intention to study the effect of anodizing on the Al–Zr based precipitates in the coating. Detailed microstructural characterization of the coating and anodized layer was carried out using high resolution scanning and transmission electron microscopy, grazing incidence X-ray diffraction analysis, glow discharge optical emission spectroscopy, and optical appearance using spectrophotometry. The evolution of microstructure in the anodized layer as a function of anodizing parameters and their influence on the interaction of light is investigated and the results in general are applicable to discolouration of anodized layer on

  15. Anodized dental implant surface

    Directory of Open Access Journals (Sweden)

    Sunil Kumar Mishra

    2017-01-01

    Full Text Available Purpose: Anodized implants with moderately rough surface were introduced around 2000. Whether these implants enhanced biologic effect to improve the environment for better osseointegration was unclear. The purpose of this article was to review the literature available on anodized surface in terms of their clinical success rate and bone response in patients till now. Materials and Methods: A broad electronic search of MEDLINE and PubMed databases was performed. A focus was made on peer-reviewed dental journals. Only articles related to anodized implants were included. Both animal and human studies were included. Results: The initial search of articles resulted in 581 articles on anodized implants. The initial screening of titles and abstracts resulted in 112 full-text papers; 40 animal studies, 16 studies on cell adhesion and bacterial adhesion onto anodized surfaced implants, and 47 human studies were included. Nine studies, which do not fulfill the inclusion criteria, were excluded. Conclusions: The long-term studies on anodized surface implants do favor the surface, but in most of the studies, anodized surface is compared with that of machined surface, but not with other surfaces commercially available. Anodized surface in terms of clinical success rate in cases of compromised bone and immediately extracted sockets has shown favorable success.

  16. Anodized aluminum on LDEF

    Science.gov (United States)

    Golden, Johnny L.

    1993-01-01

    A compilation of reported analyses and results obtained for anodized aluminum flown on the Long Duration Exposure Facility (LDEF) was prepared. Chromic acid, sulfuric acid, and dyed sulfuric acid anodized surfaces were exposed to the space environment. The vast majority of the anodized surface on LDEF was chromic acid anodize because of its selection as a thermal control coating for use on the spacecraft primary structure, trays, tray clamps, and space end thermal covers. Reports indicate that the chromic acid anodize was stable in solar absorptance and thermal emittance, but that contamination effects caused increases in absorptance on surfaces exposed to low atomic oxygen fluences. There were some discrepancies, however, in that some chromic acid anodized specimens exhibited significant increases in absorptance. Sulfuric acid anodized surfaces also appeared stable, although very little surface area was available for evaluation. One type of dyed sulfuric acid anodize was assessed as an optical baffle coating and was observed to have improved infrared absorptance characteristics with exposure on LDEF.

  17. Anodizing Aluminum with Frills.

    Science.gov (United States)

    Doeltz, Anne E.; And Others

    1983-01-01

    "Anodizing Aluminum" (previously reported in this journal) describes a vivid/relevant laboratory experience for general chemistry students explaining the anodizing of aluminum in sulfuric acid and constrasting it to electroplating. Additions to this procedure and the experiment in which they are used are discussed. Reactions involved are…

  18. Anodized dental implant surface.

    Science.gov (United States)

    Mishra, Sunil Kumar; Kumar, Muktadar Anand; Chowdhary, Ramesh

    2017-01-01

    Anodized implants with moderately rough surface were introduced around 2000. Whether these implants enhanced biologic effect to improve the environment for better osseointegration was unclear. The purpose of this article was to review the literature available on anodized surface in terms of their clinical success rate and bone response in patients till now. A broad electronic search of MEDLINE and PubMed databases was performed. A focus was made on peer-reviewed dental journals. Only articles related to anodized implants were included. Both animal and human studies were included. The initial search of articles resulted in 581 articles on anodized implants. The initial screening of titles and abstracts resulted in 112 full-text papers; 40 animal studies, 16 studies on cell adhesion and bacterial adhesion onto anodized surfaced implants, and 47 human studies were included. Nine studies, which do not fulfill the inclusion criteria, were excluded. The long-term studies on anodized surface implants do favor the surface, but in most of the studies, anodized surface is compared with that of machined surface, but not with other surfaces commercially available. Anodized surface in terms of clinical success rate in cases of compromised bone and immediately extracted sockets has shown favorable success.

  19. Mask industry quality assessment

    Science.gov (United States)

    Strott, Al; Bassist, Larry

    1994-12-01

    Product quality and timely delivery are two of the most important parameters in determining the success of a mask manufacturing facility. Because of the sensitivity of this data, very little was known about industry performance in these areas until an assessment was authored and presented at the 1993 BACUS Symposium by Larry Regis of Intel Corporation, Neil Paulsen of Intel Corporation, and James A. Reynolds of Reynolds Consulting. This data has been updated and will be published and presented at this year's BACUS Symposium. Contributor identities will again remain protected by utilizing Arthur Andersen & Company to compile the submittals. Participation was consistent with last year's representation of over 75% of the total merchant and captive mask volume in the United States. The data compiled includes shipments, customer return rate, customer return reasons from 1988 through Q2, 1994, performance to schedule, plate survival yield, and throughput time (TPT).

  20. Masked multichannel analyzer

    Science.gov (United States)

    Winiecki, A.L.; Kroop, D.C.; McGee, M.K.; Lenkszus, F.R.

    1984-01-01

    An analytical instrument and particularly a time-of-flight-mass spectrometer for processing a large number of analog signals irregularly spaced over a spectrum, with programmable masking of portions of the spectrum where signals are unlikely in order to reduce memory requirements and/or with a signal capturing assembly having a plurality of signal capturing devices fewer in number than the analog signals for use in repeated cycles within the data processing time period.

  1. Mask strategy at International SEMATECH

    Science.gov (United States)

    Kimmel, Kurt R.

    2002-08-01

    International SEMATECH (ISMT) is a consortium consisting of 13 leading semiconductor manufacturers from around the globe. Its objective is to develop the infrastructure necessary for its member companies to realize the International Technology Roadmap for Semiconductors (ITRS) through efficiencies of shared development resources and knowledge. The largest area of effort is lithography, recognized as a crucial enabler for microelectronics technology progress. Within the Lithography Division, most of the efforts center on mask-related issues. The development strategy at International SEMATCH will be presented and the interlock of lithography projects clarified. Because of the limited size of the mask production equipment market, the business case is weak for aggressive investment commensurate with the pace of the International Technology Roadmap for Semiconductors. With masks becoming the overwhelming component of lithography cost, new ways of reducing or eliminating mask costs are being explored. Will mask technology survive without a strong business case? Will the mask industry limit the growth of the semiconductor industry? Are advanced masks worth their escalating cost? An analysis of mask cost from the perspective of mask value imparted to the user is presented with examples and generic formulas for the reader to apply independently. A key part to the success for both International SEMATECH and the industry globally will be partnerships on both the local level between mask-maker and mask-user, and the macro level where global collaborations will be necessary to resolve technology development cost challenges.

  2. BIRD FLU MASKS

    Directory of Open Access Journals (Sweden)

    YASAR KESKIN

    2006-08-01

    Full Text Available Avian influenza (bird flu is a disease of birds caused by influenza viruses closely related to human influenza viruses. The potential for transformation of avian influenza into a form that both causes severe disease in humans and spreads easily from person to person is a great concern for world health. The main purpose of a mask is to help prevent particles (droplets being expelled into the environment by the wearer. Masks are also resistant to fluids, and help protect the wearer from splashes of blood or other potentially infectious substances. They are not necessarily designed for filtration efficiency, or to seal tightly to the face. Masks and respirators are components of a number of infection control measures intended to protect healthcare workers, and prevent the spread of diseases. All healthcare workers who come into contact with a possible or probable case of any respiratory track infections should wear a respirator conforming to at least EN149:2001 FFP3. [TAF Prev Med Bull 2006; 5(4.000: 296-306

  3. Acetic acid mediated interactions between alumina surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Sato, Kimiyasu, E-mail: sato.kimiyasu@aist.go.jp [National Institute of Advanced Industrial Science and Technology (AIST), Anagahora 2266-98, Shimoshidami, Moriyama-ku, Nagoya 463-8560 (Japan); Y Latin-Small-Letter-Dotless-I lmaz, Hueseyin [National Institute of Advanced Industrial Science and Technology (AIST), Anagahora 2266-98, Shimoshidami, Moriyama-ku, Nagoya 463-8560 (Japan); Gebze Institute of Technology, Materials Science and Engineering Department, 41400, Gebze-Kocaeli (Turkey); Ijuin, Atsuko; Hotta, Yuji; Watari, Koji [National Institute of Advanced Industrial Science and Technology (AIST), Anagahora 2266-98, Shimoshidami, Moriyama-ku, Nagoya 463-8560 (Japan)

    2012-02-01

    Low-molecular-weight organic acids have been known to modify colloidal stability of alumina-based suspensions. We investigated interaction forces between alumina surfaces mediated by acetic acid which is one of the simplest organic acids. Forces between alumina surfaces were measured using the colloid-probe method of atomic force microscope (AFM). Repulsive forces attributed to steric repulsion due to adsorbed molecules and electrostatic repulsion dominated the interaction. Results of rheological characterization of the alumina slurry containing acetic acid supported the finding.

  4. Structural Effects of Lanthanide Dopants on Alumina

    Science.gov (United States)

    Patel, Ketan; Blair, Victoria; Douglas, Justin; Dai, Qilin; Liu, Yaohua; Ren, Shenqiang; Brennan, Raymond

    2017-01-01

    Lanthanide (Ln3+) doping in alumina has shown great promise for stabilizing and promoting desirable phase formation to achieve optimized physical and chemical properties. However, doping alumina with Ln elements is generally accompanied by formation of new phases (i.e. LnAlO3, Ln2O3), and therefore inclusion of Ln-doping mechanisms for phase stabilization of the alumina lattice is indispensable. In this study, Ln-doping (400 ppm) of the alumina lattice crucially delays the onset of phase transformation and enables phase population control, which is achieved without the formation of new phases. The delay in phase transition (θ → α), and alteration of powder morphology, particle dimensions, and composition ratios between α- and θ-alumina phases are studied using a combination of solid state nuclear magnetic resonance, electron microscopy, digital scanning calorimetry, and high resolution X-ray diffraction with refinement fitting. Loading alumina with a sparse concentration of Ln-dopants suggests that the dopants reside in the vacant octahedral locations within the alumina lattice, where complete conversion into the thermodynamically stable α-domain is shown in dysprosium (Dy)- and lutetium (Lu)-doped alumina. This study opens up the potential to control the structure and phase composition of Ln-doped alumina for emerging applications.

  5. Structural Effects of Lanthanide Dopants on Alumina

    Energy Technology Data Exchange (ETDEWEB)

    Patel, Ketan; Blair, Victoria; Douglas, Justin; Dai, Qilin; Liu, Yaohua; Ren, Shenqiang; Brennan, Raymond

    2017-01-06

    Lanthanide (Ln3+) doping in alumina has shown great promise for stabilizing and promoting desirable phase formation to achieve optimized physical and chemical properties. However, doping alumina with Ln elements is generally accompanied by formation of new phases (i.e. LnAlO3, Ln2O3), and therefore inclusion of Ln-doping mechanisms for phase stabilization of the alumina lattice is indispensable. In this study, Ln-doping (400 ppm) of the alumina lattice crucially delays the onset of phase transformation and enables phase population control, which is achieved without the formation of new phases. The delay in phase transition (θ → α), and alteration of powder morphology, particle dimensions, and composition ratios between α- and θ-alumina phases are studied using a combination of solid state nuclear magnetic resonance, electron microscopy, digital scanning calorimetry, and high resolution X-ray diffraction with refinement fitting. Loading alumina with a sparse concentration of Ln-dopants suggests that the dopants reside in the vacant octahedral locations within the alumina lattice, where complete conversion into the thermodynamically stable α-domain is shown in dysprosium (Dy)- and lutetium (Lu)-doped alumina. This study opens up the potential to control the structure and phase composition of Ln-doped alumina for emerging applications.

  6. Generation of Porous Alumina Layers in a Polydimethylsiloxane/Hydrogen Peroxide Medium on Aluminum Substrate in Corona Discharges

    Directory of Open Access Journals (Sweden)

    A. Groza

    2014-01-01

    Full Text Available The porous alumina (Al2O3 layer obtained at the interface between polydimethylsiloxane/hydrogen peroxide medium and aluminum substrate under charged and neutral species injection produced in negative corona discharges in air at atmospheric pressure is analyzed by different methods in this paper. The scanning electron microscopy investigations showed the uniform distribution of the pores formed in the alumina layer and their columnar structures. Both energy dispersive X-ray spectroscopy (EDS and X-ray photoelectron spectroscopy (XPS measurements indicate that during the anodization process of the aluminum in the polydimethylsiloxane/hydrogen peroxide medium in corona discharge the incorporation of silicon in the structure of the alumina layer is possible.

  7. Influence of Alumina Addition on the Optical Property of Zirconia/Alumina Composite Dental Ceramics

    Institute of Scientific and Technical Information of China (English)

    JIANG Li; LIAO Yunmao; LI Wei; WAN Qianbing; ZHAO Yongqi

    2011-01-01

    The influence of various alumina additions on the optical property of zirconia/alumina composite ceramics was investigated.The relative sintered densities,transmittances,color and the microstructure of the composite ceramics were studied.The experimental results showed that the relative sintered densities and transmittances decreased with alumina addition.The lightness increased obviously but the chroma change was small.Pure zirconia nanopowders sintered densely could obtain the relatively high transmittance,while the transmittance and the lightness of slight addition changed significantly.The zirconia/alumina composite ceramics with alumina addition less than 7.5wt% could achieve the relatively stable and reliable optical properties.

  8. Electrically conductive anodized aluminum coatings

    Science.gov (United States)

    Alwitt, Robert S. (Inventor); Liu, Yanming (Inventor)

    2001-01-01

    A process for producing anodized aluminum with enhanced electrical conductivity, comprising anodic oxidation of aluminum alloy substrate, electrolytic deposition of a small amount of metal into the pores of the anodized aluminum, and electrolytic anodic deposition of an electrically conductive oxide, including manganese dioxide, into the pores containing the metal deposit; and the product produced by the process.

  9. Mask alignment system for semiconductor processing

    Energy Technology Data Exchange (ETDEWEB)

    Webb, Aaron P.; Carlson, Charles T.; Weaver, William T.; Grant, Christopher N.

    2017-02-14

    A mask alignment system for providing precise and repeatable alignment between ion implantation masks and workpieces. The system includes a mask frame having a plurality of ion implantation masks loosely connected thereto. The mask frame is provided with a plurality of frame alignment cavities, and each mask is provided with a plurality of mask alignment cavities. The system further includes a platen for holding workpieces. The platen may be provided with a plurality of mask alignment pins and frame alignment pins configured to engage the mask alignment cavities and frame alignment cavities, respectively. The mask frame can be lowered onto the platen, with the frame alignment cavities moving into registration with the frame alignment pins to provide rough alignment between the masks and workpieces. The mask alignment cavities are then moved into registration with the mask alignment pins, thereby shifting each individual mask into precise alignment with a respective workpiece.

  10. Assessing EUV mask defectivity

    Science.gov (United States)

    Okoroanyanwu, Uzodinma; Tchikoulaeva, Anna; Ackmann, Paul; Wood, Obert; La Fontaine, Bruno; Bubke, Karsten; Holfeld, Christian; Peters, Jan Hendrik; Kini, Sumanth; Watson, Sterling; Lee, Isaac; Mu, Bo; Lim, Phillip; Raghunathan, Sudhar; Boye, Carol

    2010-04-01

    This paper assesses the readiness of EUV masks for pilot line production. The printability of well characterized reticle defects, with particular emphasis on those reticle defects that cause electrical errors on wafer test chips, is investigated. The reticles are equipped with test marks that are inspected in a die-to-die mode (using DUV inspection tool) and reviewed (using a SEM tool), and which also comprise electrically testable patterns. The reticles have three modules comprising features with 32 nm ground rules in 104 nm pitch, 22 nm ground rules with 80 nm pitch, and 16 nm ground rules with 56 nm pitch (on the wafer scale). In order to determine whether specific defects originate from the substrate, the multilayer film, the absorber stack, or from the patterning process, the reticles were inspected after each fabrication step. Following fabrication, the reticles were used to print wafers on a 0.25 NA full-field ASML EUV exposure tool. The printed wafers were inspected with state of the art bright-field and Deep UV inspection tools. It is observed that the printability of EUV mask defects down to a pitch of 56 nm shows a trend of increased printability as the pitch of the printed pattern gets smaller - a well established trend at larger pitches of 80 nm and 104 nm, respectively. The sensitivity of state-of-the-art reticle inspection tools is greatly improved over that of the previous generation of tools. There appears to be no apparent decline in the sensitivity of these state-of-the-art reticle inspection tools for higher density (smaller) patterns on the mask, even down to 56nm pitch (1x). Preliminary results indicate that a blank defect density of the order of 0.25 defects/cm2 can support very early learning on EUV pilot line production at the 16nm node.

  11. Nanostructures Using Anodic Aluminum Oxide

    Science.gov (United States)

    Valmianski, Ilya; Monton, Carlos M.; Pereiro, Juan; Basaran, Ali C.; Schuller, Ivan K.

    2013-03-01

    We present two fabrication methods for asymmetric mesoscopic dot arrays over macroscopic areas using anodic aluminum oxide templates. In the first approach, metal is deposited at 45o to the template axis to partially close the pores and produce an elliptical shadow-mask. In the second approach, now underway, nanoimprint lithography on a polymer intermediary layer is followed by reactive ion etching to generate asymmetric pore seeds. Both these techniques are quantified by an analysis of the lateral morphology and lattice of the pores or dots using scanning electron microscopy and a newly developed MATLAB based code (available for free download at http://ischuller.ucsd.edu). The code automatically provides a segmentation of the measured area and the statistics of morphological properties such as area, diameter, and eccentricity, as well as the lattice properties such as number of nearest neighbors, and unbiased angular and radial two point correlation functions. Furthermore, novel user defined statistics can be easily obtained. We will additionally present several applications of these methods to superconducting, ferromagnetic, and organic nanostructures. This work is supported by AFOSR FA9550-10-1-0409

  12. Frequency Shifts of Luminescence for ZnO Nanoparticles in Porous Alumina Template

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    ZnO nanoparticles in porous anodized alumina were fabricated by sol-gel method. The PL spectra of pure ZnO nanoparticles, porous alumina template and the ZnO/PAA composite system were investigated after annealed at different temperatures. The annealing of ZnO/PAA composite system displays very complicated behavior, where changing of luminescence intensity and a "red shift" of emission frequency were observed at less or higher than 500 ℃ of the annealing temperature, respectively. To explain the phenomenon, it is considered that the emission origin of the green luminescence of ZnO nanoparticles came from OZn. It is suggested that the ZnO/PAA composite system should be annealed at the temperature above 500 ℃ in order to get intense luminescence of ZnO nanoparticle.

  13. Glutathione transferases immobilized on nanoporous alumina: flow system kinetics, screening, and stability.

    Science.gov (United States)

    Kjellander, Marcus; Mazari, Aslam M A; Boman, Mats; Mannervik, Bengt; Johansson, Gunnar

    2014-02-01

    The previously uncharacterized Drosophila melanogaster Epsilon-class glutathione transferases E6 and E7 were immobilized on nanoporous alumina. The nanoporous anodized alumina membranes were derivatized with 3-aminopropyl-triethoxysilane, and the amino groups were activated with carbonyldiimidazole to allow coupling of the enzymes via ε-amino groups. Kinetic analyses of the immobilized enzymes were carried out in a circulating flow system using CDNB (1-chloro-2,4-dinitrobenzene) as substrate, followed by specificity screening with alternative substrates. A good correlation was observed between the substrate screening data for immobilized enzyme and corresponding data for the enzyme in solution. A limited kinetic study was also carried out on immobilized human GST S1-1 (also known as hematopoietic prostaglandin D synthase). The stability of the immobilized enzymes was virtually identical to that of enzymes in solution, and no leakage of enzyme from the matrix could be observed.

  14. 热处理对铝箔阳极氧化膜结构与电化学特征的影响%Effect of heat treatment on microstructure and electrochemical characteristics of anodized alumina oxide film formed on Al foils

    Institute of Scientific and Technical Information of China (English)

    班朝磊; 何业东; 邵鑫

    2011-01-01

    将高压铝电解电容器用腐蚀铝箔在硼酸电解质溶液中进行530 V阳极氧化,应用透射电镜、X射线衍射与交流阻抗对比研究了阳极氧化对铝箔实施500℃×2 min热处理前后对表面高压阳极氧化膜的微观结构与电化学特征的影响。结果表明:高压阳极氧化膜具有明显的层状结构特征,外层晶化程度较低、晶粒细小;内层晶化程度较高、晶粒较为粗大;热处理后可以显著提高氧化膜各层的结晶程度、单位厚度阳极氧化膜耐电场强度增加,减弱了对铝箔表面隧道微孔的堵塞程度,氧化膜表观比电容相应增大,热处理及其随后的修补化成提高了阳极氧化膜的致密程度,氧化膜表观比电阻也相应增加。%Aluminum capacitor foils with tunnel etch structure were reacted with boiling water and were then anodized at 530 V in boric acid solution.During anodization,some Al foils were treated at 500 ℃ for 2 min and the others were not.Specimens of oxide film on etched Al foil were successfully prepared with focused ion beam thinning technique for TEM examination.The effect of heat treatment on microstructure,crystallinity and electrochemical performance of the anodized oxide film was examined by TEM,XRD and EIS.The results show that the film consists of distinct inner and outer layers.The crystallization with smaller crystallites in the outer layer are less than those in the inner layer.However,the heat treatment is favorable to improving the crystallinity and field strength of the film,which can reduce the tendency of the film to block up tiny etch tunnels of the Al foil and increase its specific capacitance.The heat treatment and following reanodization can also enhance the compact of the film,leading to increase its apparent specific resistance.

  15. 柠檬酸对腐蚀铝箔高压阳极氧化膜微观结构与电化学性能的影响%Effect of citric acid on microstructure and electrochemical characteristics of high voltage anodized alumina film formed on etched Al Foils

    Institute of Scientific and Technical Information of China (English)

    班朝磊; 何业东; 邵鑫

    2011-01-01

    将高压铝电解电容器用腐蚀铝箔与沸水反应,然后再在硼酸溶液或硼酸-柠檬酸混合酸溶液中进行530 V高压阳极氧化制得耐压薄膜,应用透射电镜(TEM)、X射线衍射(XRD)研究不同电解液所形成的高压阳极氧化膜的微观结构与结晶程度,利用电化学交流阻抗(EIS)、LCR数字电桥与小电流充电测试阳极氧化膜的电化学性能.结果表明:高压阳极氧化膜具有明显层状结构,内层结晶程度较高、外层结晶程度较低;与单纯硼酸溶液所形成的氧化膜相比,混合酸液所形成的阳极氧化膜的外层结晶程度与晶粒平均尺寸较大,抗电场强度与比电容均比较高,但相变使得氧化膜外层微观缺陷密度增多,氧化膜比电阻与耐电压值有所降低.%Aluminum capacitor foils with a tunnel etch structure were reacted with boiling water and then anodized at 530 V in boric acid solution or boric acid+citric acid mixed solution. The microstructure and crystallinity of the resulting anodized film were examined by TEM and XRD. The special capacitance, resistance and withstanding voltage of the film were explored with electrochemical impedance spectroscopy (EIS), LCR meter and small-current charging. The results show that the high voltage anodized oxide film consists of an inner layer with high crystallinity and an outer layer with low crystallinity. However, the crystallinity of the film formed in boric acid+citric acid mixed solution is higher than that of the film formed in only boric acid solution, leading to an increase in film's field strength and special capacitance. Meanwhile, there are more defects from phase transformation in the out layer of the film formed in boric acid+citric acid mixed solution than in that of film formed in only boric acid solution, leading to a decrease in film's resistance and withstanding voltage.

  16. Trends in mask data preparation

    Science.gov (United States)

    Fujimura, Aki; Pang, Liyong; Su, Bo; Choi, Yohan

    2014-10-01

    Whether for VSB mask writing or for multibeam mask writing, the shapes we need to write on masks are increasingly complex, increasingly curvilinear, and smaller in minimum width and space. The overwhelming trend in mask data preparation (MDP) is the shift from deterministic, rule-based, geometric, context-independent, shape-modulated, rectangular processing to statistical, simulation-based, context-dependent, dose- and shape-modulated any-shape processing. The paper briefly surveys the history of MDP, and explains through a simulation-based study that 50nm line and space is the tipping point where rule-based processing gives away to simulation-based processing.

  17. Masked hypertension: a systematic review.

    Science.gov (United States)

    Bobrie, Guillaume; Clerson, Pierre; Ménard, Joël; Postel-Vinay, Nicolas; Chatellier, Gilles; Plouin, Pierre-François

    2008-09-01

    The purpose of this research was to review the literature on masked hypertension. Studies, reviews and editorials on masked hypertension were identified by PubMed, Pascal BioMed and Cochrane literature systematic searches. Then, we carried out a meta-analysis of the six cohort studies reporting quantitative data for masked hypertension prognosis. There is still no clear consensus definition of masked hypertension and the reproducibility of the phenomenon is unknown. Nevertheless, the prevalence of masked hypertension seems to lie between 8 and 20%, and can be up to 50% in treated hypertensive patients. Subjects with masked hypertension have a higher risk of cardiovascular accidents [hazard ratios: 1.92 (1.51-2.44)] than normotensive subjects. This is due to a possible failure to recognize and appropriately manage this particular form of hypertension, the frequent association with other risk factors and coexisting target organ damage. The remaining unresolved questions are as follows: is masked hypertension a clinical entity that requires identification and characterization or a statistical phenomenon linked to the variability of blood pressure measurements?; because screening of the entire population is not feasible, how to identify individuals with masked hypertension?; and, in the absence of randomized trial, how to treat masked hypertension?

  18. What Is Being Masked in Object Substitution Masking?

    Science.gov (United States)

    Gellatly, Angus; Pilling, Michael; Cole, Geoff; Skarratt, Paul

    2006-01-01

    Object substitution masking (OSM) is said to occur when a perceptual object is hypothesized that is mismatched by subsequent sensory evidence, leading to a new hypothesized object being substituted for the first. For example, when a brief target is accompanied by a longer lasting display of nonoverlapping mask elements, reporting of target…

  19. SEMATECH EUVL mask program status

    Science.gov (United States)

    Yun, Henry; Goodwin, Frank; Huh, Sungmin; Orvek, Kevin; Cha, Brian; Rastegar, Abbas; Kearney, Patrick

    2009-04-01

    As we approach the 22nm half-pitch (hp) technology node, the industry is rapidly running out of patterning options. Of the several lithography techniques highlighted in the International Technology Roadmap for Semiconductors (ITRS), the leading contender for the 22nm hp insertion is extreme ultraviolet lithography (EUVL). Despite recent advances with EUV resist and improvements in source power, achieving defect free EUV mask blank and enabling the EUV mask infrastructure still remain critical issues. To meet the desired EUV high volume manufacturing (HVM) insertion target date of 2013, these obstacles must be resolved on a timely bases. Many of the EUV mask related challenges remain in the pre-competitive stage and a collaborative industry based consortia, such as SEMATECH can play an important role to enable the EUVL landscape. SEMATECH based in Albany, NY is an international consortium representing several of the largest manufacturers in the semiconductor market. Full members include Intel, Samsung, AMD, IBM, Panasonic, HP, TI, UMC, CNSE (College of Nanoscience and Engineering), and Fuller Road Management. Within the SEMATECH lithography division a major thrust is centered on enabling the EUVL ecosystem from mask development, EUV resist development and addressing EUV manufacturability concerns. An important area of focus for the SEMATECH mask program has been the Mask Blank Development Center (MBDC). At the MBDC key issues in EUV blank development such as defect reduction and inspection capabilities are actively pursued together with research partners, key suppliers and member companies. In addition the mask program continues a successful track record of working with the mask community to manage and fund critical mask tools programs. This paper will highlight recent status of mask projects and longer term strategic direction at the MBDC. It is important that mask technology be ready to support pilot line development HVM by 2013. In several areas progress has been

  20. Synthesis of embossing Si nanomesh and its application as an anode for lithium ion batteries

    Science.gov (United States)

    Cho, Sanghyun; Jang, Ho Young; Jung, Insub; Liu, Lichun; Park, Sungho

    2017-09-01

    Voids in nanostructured silicon (Si) anodes are believed to effectively mitigate the gradual performance degradation during repeated charge/discharge in lithium ion batteries (LIBs). In this work, we first demonstrate an embossing Si nanomesh structure bearing substantial voids in three dimensions for LIB applications. A solid alumina framework and a sacrificial layer of Ag serve as a template for embossing Si nanomesh structures. After complete dissolution of the alumina framework and the Ag layer, an embossing Si nanomesh exhibits highly ordered and high density nanoholes in an interconnected framework. The model Si nanomesh fabricated by our method has holes ∼70 nm in diameter, has ∼96 holes/μm2, and is ∼40 nm in thickness. We use this void-rich embossing Si nanomesh as a LIB anode, achieving significant enhancement in battery performance in terms of discharge capacity, cycling stability, and structural maintenance compared to a counterpart Si nanofilm without voids.

  1. Masked Repetition Priming Using Magnetoencephalography

    Science.gov (United States)

    Monahan, Philip J.; Fiorentino, Robert; Poeppel, David

    2008-01-01

    Masked priming is used in psycholinguistic studies to assess questions about lexical access and representation. We present two masked priming experiments using MEG. If the MEG signal elicited by words reflects specific aspects of lexical retrieval, then one expects to identify specific neural correlates of retrieval that are sensitive to priming.…

  2. Masked hypertension in diabetes mellitus

    DEFF Research Database (Denmark)

    Franklin, Stanley S; Thijs, Lutgarde; Li, Yan

    2013-01-01

    Although distinguishing features of masked hypertension in diabetics are well known, the significance of antihypertensive treatment on clinical practice decisions has not been fully explored. We analyzed 9691 subjects from the population-based 11-country International Database on Ambulatory Blood...... Pressure in Relation to Cardiovascular Outcomes. Prevalence of masked hypertension in untreated normotensive participants was higher (P...

  3. Fabrication of nanopore and nanoparticle arrays with high aspect ratio AAO masks

    Science.gov (United States)

    Li, Z. P.; Xu, Z. M.; Qu, X. P.; Wang, S. B.; Peng, J.; Mei, L. H.

    2017-03-01

    How to use high aspect ratio anodic aluminum oxide (AAO) membranes as an etching and evaporation mask is one of the unsolved problems in the application of nanostructured arrays. Here we describe the versatile utilizations of the highly ordered AAO membranes with a high aspect ratio of more than 20 used as universal masks for the formation of various nanostructure arrays on various substrates. The result shows that the fabricated nanopore and nanoparticle arrays of substrates inherit the regularity of the AAO membranes completely. The flat AAO substrates and uneven AAO frontages were attached to the Si substrates respectively as an etching mask, which demonstrates that the two kinds of replication, positive and negative, represent the replication of the mirroring of Si substrates relative to the flat AAO substrates and uneven AAO frontages. Our work is a breakthrough for the broad research field of surface nano-masking.

  4. Alumina forming iron base superalloy

    Energy Technology Data Exchange (ETDEWEB)

    Yamamoto, Yukinori; Muralidharan, Govindarajan; Brady, Michael P.

    2014-08-26

    An austenitic stainless steel alloy, consists essentially of, in weight percent 2.5 to 4 Al; 25 to 35 Ni; 12 to 19 Cr; at least 1, up to 4 total of at least one element selected from the group consisting of Nb and Ta; 0.5 to 3 Ti; less than 0.5 V; 0.1 to 1 of at least on element selected from the group consisting of Zr and Hf; 0.03 to 0.2 C; 0.005 to 0.1 B; and base Fe. The weight percent Fe is greater than the weight percent Ni. The alloy forms an external continuous scale including alumina, and contains coherent precipitates of .gamma.'-Ni.sub.3Al, and a stable essentially single phase FCC austenitic matrix microstructure. The austenitic matrix is essentially delta-ferrite-free and essentially BCC-phase-free.

  5. Dissolution Kinetics of Alumina Calcine

    Energy Technology Data Exchange (ETDEWEB)

    Batcheller, Thomas Aquinas

    2001-09-01

    Dissolution kinetics of alumina type non-radioactive calcine was investigated as part of ongoing research that addresses permanent disposal of Idaho High Level Waste (HLW). Calcine waste was produced from the processing of nuclear fuel at the Idaho Nuclear Technology and Engineering Center (INTEC). Acidic radioactive raffinates were solidified at ~500°C in a fluidized bed reactor to form the dry granular calcine material. Several Waste Management alternatives for the calcine are presented in the Idaho High Level Waste Draft EIS. The Separations Alternative addresses the processing of the calcine so that the HLW is ready for removal to a national geological repository by the year 2035. Calcine dissolution is the key front-end unit operation for the separations alternative.

  6. Self-organized magnetic nanowire arrays based on alumina and titania templates.

    Science.gov (United States)

    Prida, V M; Pirota, K R; Navas, D; Asenjo, A; Hernández-Vélez, M; Vázquez, M

    2007-01-01

    Densely packed arrays of magnetic nanowires have been synthesized by electrodeposition filling of nanopores in alumina and titania membranes formed by self-assembling during anodization process. Emphasis is made on the control of the production parameters leading to ordering degree and lattice parameter of the array as well as nanowires diameter and length. Structural, morphological and magnetic properties exhibited by nanowire arrays have been studied for several nanowire compositions, different ordering degree and for different nanowire aspect ratios. The magnetic behaviour of nanowires array is governed by the balance between different energy contributions: shape anisotropy of individual nanowires, the magnetostatic interaction of dipolar origin among nanowires, and magnetocrystalline and magnetoelastic anisotropies induced by the pattern templates. These novel nanocomposites, based on ferromagnetic nanowires embedded in anodic nanoporous templates, are becoming promising candidates for technological applications such as functionalised arrays for magnetic sensing, ultrahigh density magnetic storage media or spin-based electronic devices.

  7. Recent Development of High Alumina Refractories in China

    Institute of Scientific and Technical Information of China (English)

    WANGJin-xiang; LIUJie-hua

    1994-01-01

    The paper reviews the achievements which have been attained recently in China in high alumina refractories raw materials and their products,including 1) homogenization ,urification and electric fusion of high alumina raw materials and synthesizing of spinel from natural raw materials;2) processing principle and characteristics and microstructural features of creep-resistance high alu-mina brick ,alumina-magnesia-carbon brick and thermal shock resistanced high alumina brikc and their application in practice.

  8. Fracture toughness of advanced alumina ceramics and alumina matrix composites used for cutting tool edges

    Directory of Open Access Journals (Sweden)

    M. Szutkowska

    2012-10-01

    Full Text Available Purpose: Specific characteristics in fracture toughness measurements of advanced alumina ceramics and alumina matrix composites with particular reference to α-Al2O3, Al2O3-ZrO2, Al2O3-ZrO2-TiC and Al2O3-Ti(C,N has been presented.Design/methodology/approach: The present study reports fracture toughness obtained by means of the conventional method and direct measurements of the Vickers crack length (DCM method of selected tool ceramics based on alumina: pure alumina, alumina-zirconia composite with unstabilized and stabilized zirconia, alumina–zirconia composite with addition of TiC and alumina–nitride-carbide titanium composite with 2wt% of zirconia. Specimens were prepared from submicro-scale trade powders. Vicker’s hardness (HV1, fracture toughness (KIC at room temperature, the indentation fracture toughness, Young’s modulus and apparent density were also evaluated. The microstructure was observed by means of scanning electron microscopy (SEM.Findings: The lowest value of KIC is revealed by pure alumina ceramics. The addition of (10 wt% unstabilized zirconia to alumina or a small amount (5 wt% of TiC to alumina–zirconia composite improve fracture toughness of these ceramics in comparison to alumina ceramics. Alumina ceramics and alumina-zirconia ceramics reveal the pronounced character of R-curve because of an increasing dependence on crack growth resistance with crack extension as opposed to the titanium carbide-nitride reinforced composite based on alumina. R-curve has not been observed for this composite.Practical implications: The results show the method of fracture toughness improvement of alumina tool ceramics.Originality/value: Taking into account the values of fracture toughness a rational use of existing ceramic tools should be expected.

  9. Lithium batteries, anodes, and methods of anode fabrication

    KAUST Repository

    Li, Lain-Jong

    2016-12-29

    Prelithiation of a battery anode carried out using controlled lithium metal vapor deposition. Lithium metal can be avoided in the final battery. This prelithiated electrode is used as potential anode for Li- ion or high energy Li-S battery. The prelithiation of lithium metal onto or into the anode reduces hazardous risk, is cost effective, and improves the overall capacity. The battery containing such an anode exhibits remarkably high specific capacity and a long cycle life with excellent reversibility.

  10. Fabrication of diameter-modulated and ultrathin porous nanowires in anodic aluminum oxide templates

    Energy Technology Data Exchange (ETDEWEB)

    Sulka, Grzegorz D., E-mail: Sulka@chemia.uj.edu.pl [Max Planck Institute of Microstructure Physics, Weinberg 2, 06120 Halle (Germany); Department of Physical Chemistry and Electrochemistry, Jagiellonian University, Ingardena 3, 30060 Krakow (Poland); Brzozka, Agnieszka [AGH University of Science and Technology, Faculty of Non-Ferrous Metals, Al. Mickiewicza 30, Krakow 30-059 (Poland); Liu, Lifeng [Max Planck Institute of Microstructure Physics, Weinberg 2, 06120 Halle (Germany)

    2011-05-30

    Graphical abstract: Display Omitted Highlights: > AAO templates with modulated pore diameter were fabricated by pulse anodization. > HA pulse duration tunes the shape of pores and the structure of AAO channels. > Au, Ag, Ni and Ag-Au diameter-modulated nanowires were synthetized. > Porous ultrathin Au nanowires were obtained by dealloying Ag-Au nanowires. - Abstract: Anodic aluminum oxide (AAO) membranes with modulated pore diameter were synthesized by pulse anodization in 0.3 M sulfuric acid at 1 deg. C. For AAO growth, a typical combination of alternating mild anodizing (MA) and hard anodizing (HA) pulses with applied potential pulses of 25 V and 35 V was applied. The control of the duration of HA pulses will provide an interesting way to tune the shape of pores and the structure of AAO channels. It was found that a non-uniform length of HA segments in cross section of AAO is usually observed when the HA pulse duration is shorter than 1.2 s. The pulse anodization performed with longer HA pulses leads to the formation of AAO templates with periodically modulated pore diameter and nearly uniform length of segments. Various diameter-modulated metallic nanowires (Au, Ag, Ni and Ag-Au) were fabricated by electrodeposition in the pores of anodic alumina membranes. A typical average nanowire diameter was about 30 nm and 48 nm for MA and HA nanowire segments, respectively. After a successful dealloying silver from Ag-Au nanowires, porous ultrathin Au nanowires were obtained.

  11. Application of anodizing and CAR processes for manufacturing Al/Al{sub 2}O{sub 3} composite

    Energy Technology Data Exchange (ETDEWEB)

    Jamaati, Roohollah, E-mail: r.jamaatikenari@ma.iut.ac.ir [Department of Materials Engineering, Isfahan University of Technology, Isfahan 84156-83111 (Iran, Islamic Republic of); Toroghinejad, Mohammad Reza; Najafizadeh, Abbas [Department of Materials Engineering, Isfahan University of Technology, Isfahan 84156-83111 (Iran, Islamic Republic of)

    2010-06-25

    In this study, an anodizing process with different conditions was used to grow four different thicknesses of alumina on the surface of aluminum strips. Then, a continual annealing and roll-bonding (CAR) process was done to produce an aluminum matrix composite dispersed with four different volume fractions of alumina particles. The results demonstrate that when the number of cycles was increased, the distribution of alumina particles in the aluminum matrix improved, the particles became finer, and the tensile strength of the composites increased. The microstructure of the fabricated composites after 8 CAR cycles also showed an excellent distribution of alumina particles in the matrix. Moreover, it was observed that increasing alumina quantities through longer anodizing times enhanced the tensile strength of the composite to become 1.65 times higher than that of the monolithic aluminum produced by the same method, while negligible reductions were observed in the elongation value. Fracture surfaces after tensile tests were observed by scanning electron microscopy (SEM) to investigate the failure mode. Observations reveal that the failure mode in both CAR-processed composites and monolithic aluminum was the typical ductile fracture showing deep equiaxed dimples.

  12. Burned Microporous Alumina-Graphite Brick

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    @@ 1 Scope This standard specifies the definition,classifica-tion,technical requirements,test methods,inspection rules,marking,packing,transportation and quality certificate of burned microporous alumina-graphite brick.

  13. Loss tangent measurements on unirradiated alumina

    Energy Technology Data Exchange (ETDEWEB)

    Zinkle, S.J.; Goulding, R.H. [Oak Ridge National Lab., TN (United States)

    1996-04-01

    Unirradiated room temperature loss tangent for sapphire and several commercial grades of polycrystalline alumina are complied for frequencies between 10{sup 5} and 4x10{sup 11} Hz. Sapphire exhibits significantly lower values for the loss tangent at frequencies up to 10{sup 11} Hz. The loss tangents of 3 different grades of Wesgo alumina (AL300, AL995, AL998) and 2 different grades of Coors alumina (AD94, AD995) have typical values near {approx}10{sup -4} at a frequency of 10{sup 8} Hz. On the other hand, the loss tangent of Vitox alumina exhibits a large loss peak tan d{approx} 5x10{sup -3} at this frequency.

  14. Alumina Carbon Refractory Products for Continuous Casting

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    @@ 1 Scope This standard specifies the classification.techni-cal requirements,test methods,inspection rules,packing,marking,transportation,storage and quality certificate of alumina carbon refractory products for continuous casting.

  15. Biological Activity of Masked Endotoxin

    Science.gov (United States)

    Schwarz, Harald; Gornicec, Jan; Neuper, Theresa; Parigiani, Maria Alejandra; Wallner, Michael; Duschl, Albert; Horejs-Hoeck, Jutta

    2017-01-01

    Low endotoxin recovery (LER) is a recently discovered phenomenon describing the inability of limulus amebocyte lysate (LAL)-based assays to detect lipopolysaccharide (LPS) because of a “masking effect” caused by chelators or detergents commonly used in buffer formulations for medical products and recombinant proteins. This study investigates the masking capacities of different buffer formulations and whether masked endotoxin is biologically active. We show that both naturally occurring endotoxin as well as control standard endotoxin can be affected by LER. Furthermore, whereas masked endotoxin cannot be detected in Factor C based assays, it is still detectable in a cell-based TLR4-NF-κB-luciferase reporter gene assay. Moreover, in primary human monocytes, masked LPS induces the expression of pro-inflammatory cytokines and surface activation markers even at very low concentrations. We therefore conclude that masked LPS is a potent trigger of immune responses, which emphasizes the potential danger of masked LPS, as it may pose a health threat in pharmaceutical products or compromise experimental results. PMID:28317862

  16. Aluminum oxide as a dual-functional modifier of Ni-based anodes of solid oxide fuel cells for operation on simulated biogas

    Science.gov (United States)

    Wang, Feng; Wang, Wei; Ran, Ran; Tade, Moses O.; Shao, Zongping

    2014-12-01

    Al2O3 and SnO2 additives are introduced into the Ni-YSZ cermet anode of solid oxide fuel cells (SOFCs) for operation on simulated biogas. The effects of incorporating Al2O3/SnO2 on the electrical conductivity, morphology, coking resistance and catalytic activity for biogas reforming of the cermet anode are systematically studied. The electrochemical performance of the internal reforming SOFC is enhanced by introducing an appropriate amount of Al2O3 into the anode, but it becomes worse with excess alumina addition. For SnO2, a negative effect on the electrochemical performance is demonstrated, although the coking resistance of the anode is improved. For fuel cells operating on biogas, stable operation under a polarization current for 130 h at 750 °C is achieved for a cell with an Al2O3-modified anode, while cells with unmodified or SnO2-modified Ni-YSZ anodes show much poorer stability under the same conditions. The improved performance of the cell with the Al2O3-modified anode mainly results from the suppressed coking and sintering of the anode and from the formation of NiAl2O4 in the unreduced anode. In sum, modifying the anode with Al2O3 may be a useful and facile way to improve the coking resistance and electrochemical performance of the nickel-based cermet anodes for SOFCs.

  17. Hg-Mask Coronagraph

    Science.gov (United States)

    Bourget, P.; Veiga, C. H.; Vieira Martins, R.; Assus, P.; Colas, F.

    In order to optimize the occulting process of a Lyot coronagraph and to provide a high dynamic range imaging, a new kind of occulting disk has been developed at the National Observatory of Rio de Janeiro. A mercury (Hg) drop glued onto an optical window by molecular cohesion and compressed by a pellicle film is used as the occulting disk. The minimum of the superficial tension potential function provides an optical precision (lambda/100) of the toric free surface of the mercury. This process provides a size control for the adaptation to the seeing conditions and to the apparent diameter of a resolved object, and in the case of adaptive optics, to the Airy diameter fraction needed. The occultation is a three dimensional process near the focal plane on the toric free surface that provides an apodization of the occultation. The Hg-Mask coronagraph has been projected for astrometric observations of faint satellites near to Jovian planets and works since 2000 at the 1.6 m telescope of the Pico dos Dias Observatory (OPD - Brazil).

  18. Mechanical alignment of substrates to a mask

    Energy Technology Data Exchange (ETDEWEB)

    Webb, Aaron P.; Carlson, Charles T.; Honan, Michael; Amato, Luigi G.; Grant, Christopher Neil; Strassner, James D.

    2016-11-08

    A plurality of masks is attached to the underside of a mask frame. This attachment is made such that each mask can independently move relative to the mask frame in three directions. This relative movement allows each mask to adjust its position to align with respective alignment pins disposed on a working surface. In one embodiment, each mask is attached to the mask frame using fasteners, where the fasteners have a shaft with a diameter smaller than the diameter of the mounting hole disposed on the mask. A bias element may be used to allow relative movement between the mask and the mask frame in the vertical direction. Each mask may also have kinematic features to mate with the respective alignment pins on the working surface.

  19. Anodes sliced with ions

    NARCIS (Netherlands)

    Boukamp, Bernard A.

    2006-01-01

    A detailed image of a complex fuel-cell anode structure, obtained through ion-beam milling, SEM imaging and advanced digital reconstruction, yields an accurate description of the three-dimensional structure, and enables correct prediction of the electrode's properties

  20. Anodes for alkaline electrolysis

    Science.gov (United States)

    Soloveichik, Grigorii Lev

    2011-02-01

    A method of making an anode for alkaline electrolysis cells includes adsorption of precursor material on a carbonaceous material, conversion of the precursor material to hydroxide form and conversion of precursor material from hydroxide form to oxy-hydroxide form within the alkaline electrolysis cell.

  1. Inert Anode Report

    Energy Technology Data Exchange (ETDEWEB)

    none,

    1999-07-01

    This ASME report provides a broad assessment of open literature and patents that exist in the area of inert anodes and their related cathode systems and cell designs, technologies that are relevant for the advanced smelting of aluminum. The report also discusses the opportunities, barriers, and issues associated with these technologies from a technical, environmental, and economic viewpoint.

  2. Movable anode x-ray source with enhanced anode cooling

    Science.gov (United States)

    Bird, C.R.; Rockett, P.D.

    1987-08-04

    An x-ray source is disclosed having a cathode and a disc-shaped anode with a peripheral surface at constant radius from the anode axis opposed to the cathode. The anode has stub axle sections rotatably carried in heat conducting bearing plates which are mounted by thermoelectric coolers to bellows which normally bias the bearing plates to a retracted position spaced from opposing anode side faces. The bellows cooperate with the x-ray source mounting structure for forming closed passages for heat transport fluid. Flow of such fluid under pressure expands the bellows and brings the bearing plates into heat conducting contact with the anode side faces. A worm gear is mounted on a shaft and engages serrations in the anode periphery for rotating the anode when flow of coolant is terminated between x-ray emission events. 5 figs.

  3. Vibrotactile masking through the body.

    Science.gov (United States)

    D'Amour, Sarah; Harris, Laurence R

    2014-09-01

    Touches on one hand or forearm can affect tactile sensitivity at contralateral locations on the opposite side of the body. These interactions suggest an intimate connection between the two sides of the body. Here, we explore the effect of masking not across the body but through the body by measuring the effect of a masking stimulus on the back on the tactile sensitivity of the corresponding point on the front. Tactile sensitivity was measured on each side of the stomach, while vibrotactile masking stimulation was applied to one side of the front and to points on the back including the point directly behind the test point on the front. Results were compared to sensitivity, while vibrotactile stimulation was applied to a control site on the shoulder. A reduction in sensitivity of about .8 dB was found that required the masking stimulus to be within about 2 cm of the corresponding point on the back.

  4. Fabrication of porous alumina templates with a large-scale tunable interpore distance in a H2C2O4-C2H5OH-H2O solution

    Institute of Scientific and Technical Information of China (English)

    LI Yi; LING ZhiYuan; WANG JinChi; GHEN ShuoShuo; HU Xing; HE XinHua

    2008-01-01

    Highly ordered porous alumina templates with a large-scale tunable interpore distance (100-445 nm) have been successfully fabricated under an electric field of 40-180 V by modifying oxalic acid solution with adequate alcohol. The results under our experimental conditions show that the phenomena of burning and breakdown during the high-field anodization process can be avoided by adding a proper amount of alcohol to the oxalic acid solution, An excellent linear relationship between interpore dis-tance and anodization voltage is obtained under 40-170 V, and the maximum anodization voltage that could be used to avoid burning and breakdown is 180 V.

  5. Effect of the layer of anodized 7075-T6 aluminium corrosion properties

    Science.gov (United States)

    Montoya Z, R. D.; L, E. Vera; Pineda T, Y.; Cedeño, M. L.

    2017-01-01

    Aluminium alloys are widely used in various sectors of industry. The 7075-T6 alloy corresponding to an Al-Zn T6, is mostly used as structural component in the aviation industry, due to the good relationship between weight and mechanical properties. However, the negative point of this alloys is the resistance to corrosion, which is why they need to be coated with an anodic film. Different surface treatments, such as anodizing, are used to improve corrosion resistance. Anodizing is an electrolytic process by which a protective layer on aluminium known as “alumina” is formed, this is formed by the passage of an electric current in an acidic electrolyte. This investigation presents a study of the effect of the thickness of layers of alumina deposited by anodized method, in the corrosion resistance of 7075-T6 aluminium. This study was performed by using in a solution of tartaric acid - sulfuric acid and an inorganic salt. To evaluate the influence alumina layer thickness on the corrosion properties some tests were carried out by using the electrochemical spectroscopy impedances (EIS) technique and Tafel polarization curves. It was found that the grown of the thickness of film favourably influences in the corrosion resistance.

  6. Electrical Conductivity and Corrosion Resistance of ZnFe2O4-Based Materials Used as Inert Anode for Aluminum Electrolysis

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    ZnFe2O4 and ZnFe2O4-based materials were tested to obtain the electrical conductivity and corrosion resistance in melting bath for aluminum electrolysis. The results proved that adequate additives, such as Ni2O3 CuO,Cu, ZnO and CeO2 would increase the electrical conductivity, and the ZnFe2O4-based anodes with these additives were of good corrosion resistance. The current density on anode, the mole ratio of NaF/AlF3 (MR) and the content of alumina in the bath effect the anode corrosion rate in different way.

  7. Growth and corrosion behaviors of thin anodic alumina membrane on AA5083 Al-Mg alloy in incalescent medium%非恒温电解液中AA5083 Al-Mg合金阳极氧化膜的制备及其耐蚀性

    Institute of Scientific and Technical Information of China (English)

    王加余; 李澄; 郑顺丽; 尹成勇; 王艳慧

    2014-01-01

    采用硼酸-硫酸-草酸电解液在铝合金表面制备有序多孔层,研究阳极氧化过程中电流随时间的变化,分析界面反应并计算膜层的生长效率。采用扫描电子显微镜、交流阻抗和动电位极化曲线研究膜层的微结构及其在不同温度环境下的耐蚀性。结果表明:在氧化层界面双离子层浓度的增大有利于提高膜层的生长效率。所制备的阳极氧化膜厚度为8~9μm,孔径为10~14 nm,膜层的微观形貌受金属基体组织结构的影响较大。在沸水封闭后膜层为分层结构,表面呈细片状。氧化膜层封闭后能够明显降低试样的自腐蚀电流密度,且耐蚀性随着环境温度的升高而具有更好的稳定性。%A self-ordered porous film was fabricated on aluminum alloy in a ternary boric-sulfuric-oxalic acid electrolyte system. By means of voltage-time response, the oxidation process as well as the growth efficiency was studied. Field emission scanning electron microscopy (FE-SEM) was adopted to reveal the morphological and microstructural features of as-fabricated oxide layers. The corrosion protection properties of the films were investigated by electrochemical impedance spectroscopy and potentiodynamic polarization measurements. The results showed that increasing the concentration of the double ionic layer located at the oxide interface could accelerate the film growth rate. The anodic oxidative layer with thickness of 8-9μm and pore diameter of 10-14 nm maintains the pattern and topography of workpieces, compared with the overall closed film with hierarchical structure. Both samples exhibited much lower corrosion current density after boil water sealing. Meanwhile, a superior stability could be achieved through raising the ambient temperature.

  8. Direct foaming porous alumina ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Salvini, V.R.; Sandurkov, B.A.; Klein-Gunnewiek, R.F.; Pandolfelli, V.C. [Federal Univ. of Sao Carlos, Materials Engineering Dept., FIRE Associate Lab., Sao Carlos, SP (Brazil)

    2007-07-01

    This paper presents the work carried out in order to improve the properties of these porous alumina ceramics, concerning their application as thermal insulating. Changes in solid content of ceramic suspension, variations of pore forming agents and other additives were carried out and their effects on the green and the sintered mechanical strength are also shown. According to the literature, several starch types seem to be attractive pore forming agents as well as binders for porous ceramics. Most of them consist of a mixture of two polysaccharide types, amylose (linear) and amylopectin (highly branched). Corn, potato and rice starches were used in the present study because of their difference in size and shape. In order to increase the mechanical strength of the sintered porous ceramics a part of the Al{sub 2}O{sub 3} in the composition was replaced by Al(OH){sub 3}. Due to the changes of the composition and additives, porosities up to 81% and a mechanical strength of 15 MPa were obtained. (orig.)

  9. Texture development in Al/Al{sub 2}O{sub 3} MMCs produced by anodizing and ARB processes

    Energy Technology Data Exchange (ETDEWEB)

    Jamaati, Roohollah, E-mail: r.jamaatikenari@ma.iut.ac.ir [Department of Materials Engineering, Isfahan University of Technology, Isfahan 84156-83111 (Iran, Islamic Republic of); Toroghinejad, Mohammad Reza [Department of Materials Engineering, Isfahan University of Technology, Isfahan 84156-83111 (Iran, Islamic Republic of); Hoseini, Majid [Department of Mining, Metals and Materials Engineering, McGill University, Montreal, QC H3A 2B2 (Canada); Szpunar, Jerzy A. [Department of Mechanical Engineering, University of Saskatchewan, Saskatoon, SK S7N 5A9 (Canada)

    2011-04-25

    Research highlights: {yields} The Rotated Cube was the major texture component for most specimens. {yields} The intensity of texture components was weak except the Rotated Cube component. {yields} The texture intensity of composite with low alumina particles was not weak. {yields} Alumina particles and also size and quantity of them are very effective on texture. - Abstract: Anodizing and accumulative roll bonding (ARB) processes were used as a new technique for manufacturing aluminum/alumina composites including various Al{sub 2}O{sub 3} quantities. Textural evolution during ARB process of composites was evaluated using X-ray diffraction (XRD). The effective parameters in texture evolution were the number of cycles (3, 5, 7 and 8 cycles) and alumina quantity (0.48, 1.13, 2.40 and 3.55 vol.%). The texture evolution demonstrated that the Rotated Cube was a major texture component for all specimens except for the produced composite containing 0.48 vol.% alumina after eight cycles. For subsequent composites, the dominant components were Copper and Dillamore. Also, for almost all specimens (except for the composite with 0.48 vol.% alumina), the intensity of the texture components (except for Rotated Cube) was very weak. All these results are related to the presence of the second phase particles and also size and quantity of them.

  10. Mask specification guidelines in spacer patterning technology

    Science.gov (United States)

    Hashimoto, Kohji; Mukai, Hidefumi; Miyoshi, Seiro; Yamaguchi, Shinji; Mashita, Hiromitsu; Kobayashi, Yuuji; Kawano, Kenji; Hirano, Takashi

    2008-11-01

    We have studied both the mask CD specification and the mask defect specification for spacer patterning technology (SPT). SPT has the possibility of extending optical lithography to below 40nm half-pitch devices. Since SPT necessitates somewhat more complicated wafer process flow, the CD error and mask defect printability on wafers involve more process factors compared with conventional single-exposure process (SEP). This feature of SPT implies that it is very important to determine mask-related specifications for SPT in order to select high-end mask fabrication strategies; those are for mask writing tools, mask process development, materials, inspection tools, and so on. Our experimental studies reveal that both mask CD specification and mask defect specification are somehow relaxed from those in ITRS2007. This is most likely because SPT reduces mask CD error enhanced factor (MEF) and the reduction of line-width roughness (LWR).

  11. Model of porous aluminium oxide growth during initial stage of anodization

    Science.gov (United States)

    Aryslanova, E. M.; Alfimov, A. V.; Chivilikhin, S. A.

    2014-10-01

    Currently, the development of nanotechnology and metamaterials requires the ability to obtain regular self-assembled structures with different parameters. One such structure is porous alumina in which the pores grow perpendicular to the substrate and are hexagonally packed. Pore size and the distance between them can be varied depending on the anodization voltage, the electrolyte and the anodization time (pore diameter - from 2 to 350 nm, the distance between the pores - from 5 to 50 nm). At the moment, there are different models describing the process of anodizing aluminum, in this paper we propose a model that takes into account the effect of layers of aluminum, aluminum oxide, and the electrolyte, as well as the influence of the effect of surface diffusion.

  12. Carbon nanotube/nanofiber embedded nanoporous anodized aluminium oxide surface and its tribological properties.

    Science.gov (United States)

    Kushwaha, M K; Sil, Anjan; Ray, S

    2008-08-01

    Nanoporous alumina has been prepared by anodization of pure aluminium using phosphoric acid electrolyte. Carbon nanotubes/nanofibres (CNTs/CNFs) are grown within the pores by chemical vapour deposition technique, using acetylene gas as carbon precursor. Such synthesis of nanostructured carbonaceous materials within the nanoporous oxide template has high potential for many applications (e.g., electronics, magnetic, etc.) in nanotechnology. Possibility of using such material combination for engineering systems where abrasion resistance coupled with self-lubrication (at comparatively higher loads) are the key requirements, has been explored through the present work. Pore structure has been characterized by SEM/FE-SEM in this study and CNTs/CNFs have been examined by TEM, FE-SEM and Raman spectroscopy. While the pore diameters are found to lie in the range of 180-220 nm, the CNTs/CNFs diameter are observed to be in the range of 50 to 220 nm. The CNTs/CNFs growing from bottom of the pores are found to replicate the pore diameter, while those grown above the surface are varying significantly in diameter and probably matching the diameter of the catalyst, which remains adsorbed on the top surface and inner walls of the pores. On comparing friction and wear properties of both materials (viz. anodized alumina and CNTs/CNFs embedded anodized alumina) as determined by pin-on-disc machine using hardened steel disc as counterface, it is found that wear rate and coefficient of friction of CNTs embedded composite surface is significantly lower which is attributed to formation of transfer layer of hard wear resistant alumina mechanically mixed with graphitic CNTs/CNFs.

  13. Bioactive glass-ceramics coatings on alumina

    Energy Technology Data Exchange (ETDEWEB)

    Vitale Brovarone, C.; Verne, E.; Lupo, F. [Politecnico di Torino (Italy). Materials Science and Chemical Eng. Dept.; Moisescu, C. [Jena Univ. (Germany). Otto-Schott-Inst. fuer Glaschemie; Zanardi, L.; Bosetti, M.; Cannas, M. [Eastern Piemont Univ., Novara (Italy). Medical Science Dept.

    2001-07-01

    In this work, aiming to combine the mechanical performances of alumina with the surface properties of a bioactive material, we coated full density alumina substrates by a bioactive glass-ceramic GC. This latter was specially tailored, in term of costituents and specific quantity to have a thermal expansion coefficient close to that of alumina (8.5-9{sup *}10{sup -6}/ C) which is lower than most of the bioactive glasses and glass-ceramics already in use. In this way, we sought to avoid, as much as possible, the crack formation and propagation due to residual stresses generated by the thermal expansion coefficients mismatch. Furthermore, the high reactivity of alumina toward the glass-ceramic was carefully controlled to avoid deep compositional modification of the GC that will negatively affect its bioactivity. At this purpose, an intermediate layer of an appropriate glass G was coated prior to coat the bioactive glass-ceramic. On the materials obtained, preliminary biological tests have been done to evaluate glass-ceramic biocompatibility respect to alumina. (orig.)

  14. Monitoring Transport Across Modified Nanoporous Alumina Membranes

    Directory of Open Access Journals (Sweden)

    Erich D. Steinle

    2007-11-01

    Full Text Available This paper describes the use of several characterization methods to examinealumina nanotubule membranes that have been modified with specific silanes. The functionof these silanes is to alter the transport properties through the membrane by changing thelocal environment inside the alumina nanotube. The presence of alkyl groups, either long(C18 or short and branched (isopropyl hydrocarbon chains, on these silanes significantlydecreases the rate of transport of permeant molecules through membranes containingalumina nanotubes as monitored via absorbance spectroscopy. The presence of an ionicsurfactant can alter the polarity of these modified nanotubes, which correlates to anincreased transport of ions. Fluorescent spectroscopy is also utilized to enhance thesensitivity of detecting these permeant molecules. Confirmation of the alkylsilaneattachment to the alumina membrane is achieved with traditional infrared spectroscopy,which can also examine the lifetime of the modified membrane. The physical parameters ofthese silane-modified porous alumina membranes are studied via scanning electronmicroscopy. The alumina nanotubes are not physically closed off or capped by the silanesthat are attached to the alumina surfaces.

  15. High contrast laser marking of alumina

    Energy Technology Data Exchange (ETDEWEB)

    Penide, J. [Applied Physics Department, University of Vigo, EEI, Lagoas-Marcosende, 9, Vigo 36310 (Spain); Quintero, F., E-mail: fquintero@uvigo.es [Applied Physics Department, University of Vigo, EEI, Lagoas-Marcosende, 9, Vigo 36310 (Spain); Riveiro, A. [Applied Physics Department, University of Vigo, EEI, Lagoas-Marcosende, 9, Vigo 36310 (Spain); Fernández, A. [Department of Engineering Design, University of Vigo, Escuela de Ingeniería Industrial, Campus Universitario, Vigo E-36310 (Spain); Val, J. del [Applied Physics Department, University of Vigo, EEI, Lagoas-Marcosende, 9, Vigo 36310 (Spain); Comesaña, R. [Materials Engineering, Applied Mechanics and Construction Department, University of Vigo, EEI, Lagoas-Marcosende, Vigo E-36310 (Spain); Lusquiños, F.; Pou, J. [Applied Physics Department, University of Vigo, EEI, Lagoas-Marcosende, 9, Vigo 36310 (Spain)

    2015-05-01

    Highlights: • Laser marking of alumina using near infrared (NIR) lasers was experimentally analyzed. • Color change produced by NIR lasers is due to thermally induced oxygen vacancies. • Laser marking results obtained using NIR lasers and green laser are compared. • High contrast marks on alumina were achieved. - Abstract: Alumina serves as raw material for a broad range of advanced ceramic products. These elements should usually be identified by some characters or symbols printed directly on them. In this sense, laser marking is an efficient, reliable and widely implemented process in industry. However, laser marking of alumina still leads to poor results since the process is not able to produce a dark mark, yielding bad contrast. In this paper, we present an experimental study on the process of marking alumina by three different lasers working in two wavelengths: 1064 nm (Near-infrared) and 532 nm (visible, green radiation). A colorimetric analysis has been carried out in order to compare the resulting marks and its contrast. The most suitable laser operating conditions were also defined and are reported here. Moreover, the physical process of marking by NIR lasers is discussed in detail. Field Emission Scanning Electron Microscopy, High Resolution Transmission Electron Microscopy and X-ray Photoelectron Spectroscopy were also employed to analyze the results. Finally, we propose an explanation for the differences of the coloration induced under different atmospheres and laser parameters. We concluded that the atmosphere is the key parameter, being the inert one the best choice to produce the darkest marks.

  16. Sacrificial anode stability and polarization potential variation in a ternary Al-xZn-xMg alloy in a seawater-marine environment

    Science.gov (United States)

    Muazu, Abubakar; Aliyu, Yaro Shehu; Abdulwahab, Malik; Idowu Popoola, Abimbola Patricia

    2016-06-01

    In this paper, the effects of zinc (Zn) and magnesium (Mg) addition on the performance of an aluminum-based sacrificial anode in seawater were investigated using a potential measurement method. Anodic efficiency, protection efficiency, and polarized potential were the parameters used. The percentages of Zn and Mg in the anodes were varied from 2% to 8% Zn and 1% to 4% Mg. The alloys produced were tested as sacrificial anodes for the protection of mild steel in seawater at room temperature. Current efficiency as high as 88.36% was obtained in alloys containing 6% Zn and 1% Mg. The polarized potentials obtained for the coupled (steel/Al-based alloys) are as given in the Pourbaix diagrams, with steel lying within the immunity region/cathodic region and the sacrificial anodes within the anodic region. The protection offered by the sacrificial anodes to the steel after the 7th and 8th week was measured and protection efficiency values as high as 99.66% and 99.47% were achieved for the Al-6%Zn-1%Mg cast anode. The microstructures of the cast anodes comprise of intermetallic structures of hexagonal Mg3Zn2 and body-centered cubic Al2Mg3Zn3. These are probably responsible for the breakdown of the passive alumina film, thus enhancing the anode efficiency.

  17. Electrochemical coating of dental implants with anodic porous titania for enhanced osteointegration

    Directory of Open Access Journals (Sweden)

    Amirreza Shayganpour

    2015-11-01

    Full Text Available Clinical long-term osteointegration of titanium-based biomedical devices is the main goal for both dental and orthopedical implants. Both the surface morphology and the possible functionalization of the implant surface are important points. In the last decade, following the success of nanostructured anodic porous alumina, anodic porous titania has also attracted the interest of academic researchers. This material, investigated mainly for its photocatalytic properties and for applications in solar cells, is usually obtained from the anodization of ultrapure titanium. We anodized dental implants made of commercial grade titanium under different experimental conditions and characterized the resulting surface morphology with scanning electron microscopy equipped with an energy dispersive spectrometer. The appearance of nanopores on these implants confirm that anodic porous titania can be obtained not only on ultrapure and flat titanium but also as a conformal coating on curved surfaces of real objects made of industrial titanium alloys. Raman spectroscopy showed that the titania phase obtained is anatase. Furthermore, it was demonstrated that by carrying out the anodization in the presence of electrolyte additives such as magnesium, these can be incorporated into the porous coating. The proposed method for the surface nanostructuring of biomedical implants should allow for integration of conventional microscale treatments such as sandblasting with additive nanoscale patterning. Additional advantages are provided by this material when considering the possible loading of bioactive drugs in the porous cavities.

  18. Anodization Mechanism on SiC Nanoparticle Reinforced Al Matrix Composites Produced by Power Metallurgy

    Directory of Open Access Journals (Sweden)

    Sonia C. Ferreira

    2014-12-01

    Full Text Available Specimens of aluminum-based composites reinforced by silicon carbide nanoparticles (Al/SiCnp produced by powder metallurgy (PM were anodized under voltage control in tartaric-sulfuric acid (TSA. In this work, the influence of the amount of SiCnp on the film growth during anodizing was investigated. The current density versus time response and the morphology of the porous alumina film formed at the composite surface are compared to those concerning a commercial aluminum alloy (AA1050 anodized under the same conditions. The processing method of the aluminum alloys influences the efficiency of the anodizing process, leading to a lower thicknesses for the unreinforced Al-PM alloy regarding the AA1050. The current density versus time response is strongly dependent on the amount of SiCnp. The current peaks and the steady-state current density recorded at each voltage step increases with the SiCnp volume fraction due to the oxidation of the SiCnp. The formation mechanism of the anodic film on Al/SiCnp composites is different from that occurring in AA1050, partly due the heterogeneous distribution of the reinforcement particles in the metallic matrix, but also to the entrapment of SiCnp in the anodic film.

  19. Tailoring thermal conductivity via three-dimensional porous alumina

    Science.gov (United States)

    Abad, Begoña; Maiz, Jon; Ruiz-Clavijo, Alejandra; Caballero-Calero, Olga; Martin-Gonzalez, Marisol

    2016-12-01

    Three-dimensional anodic alumina templates (3D-AAO) are an astonishing framework with open highly ordered three-dimensional skeleton structures. Since these templates are architecturally different from conventional solids or porous templates, they teem with opportunities for engineering thermal properties. By establishing the mechanisms of heat transfer in these frameworks, we aim to create materials with tailored thermal properties. The effective thermal conductivity of an empty 3D-AAO membrane was measured. As the effective medium theory was not valid to extract the skeletal thermal conductivity of 3D-AAO, a simple 3D thermal conduction model was developed, based on a mixed series and parallel thermal resistor circuit, giving a skeletal thermal conductivity value of approximately 1.25 W·m-1·K-1, which matches the value of the ordinary AAO membranes prepared from the same acid solution. The effect of different filler materials as well as the variation of the number of transversal nanochannels and the length of the 3D-AAO membrane in the effective thermal conductivity of the composite was studied. Finally, the thermal conductivity of two 3D-AAO membranes filled with cobalt and bismuth telluride was also measured, which was in good agreement with the thermal model predictions. Therefore, this work proved this structure as a powerful approach to tailor thermal properties.

  20. Tailoring thermal conductivity via three-dimensional porous alumina.

    Science.gov (United States)

    Abad, Begoña; Maiz, Jon; Ruiz-Clavijo, Alejandra; Caballero-Calero, Olga; Martin-Gonzalez, Marisol

    2016-12-09

    Three-dimensional anodic alumina templates (3D-AAO) are an astonishing framework with open highly ordered three-dimensional skeleton structures. Since these templates are architecturally different from conventional solids or porous templates, they teem with opportunities for engineering thermal properties. By establishing the mechanisms of heat transfer in these frameworks, we aim to create materials with tailored thermal properties. The effective thermal conductivity of an empty 3D-AAO membrane was measured. As the effective medium theory was not valid to extract the skeletal thermal conductivity of 3D-AAO, a simple 3D thermal conduction model was developed, based on a mixed series and parallel thermal resistor circuit, giving a skeletal thermal conductivity value of approximately 1.25 W·m(-1)·K(-1), which matches the value of the ordinary AAO membranes prepared from the same acid solution. The effect of different filler materials as well as the variation of the number of transversal nanochannels and the length of the 3D-AAO membrane in the effective thermal conductivity of the composite was studied. Finally, the thermal conductivity of two 3D-AAO membranes filled with cobalt and bismuth telluride was also measured, which was in good agreement with the thermal model predictions. Therefore, this work proved this structure as a powerful approach to tailor thermal properties.

  1. Anodisation with dynamic current control for tailored alumina coatings

    Science.gov (United States)

    Sieber, M.; Althöfer, I.; Höhlich, D.; Scharf, I.; Böttger, D.; Böttger, S.; Böttger, E.; Lampke, T.

    2016-03-01

    The anodic oxidation process is commonly used to refine the surface of aluminium and its alloys. Compared to the substrate, the alumina layers produced by anodising exhibit an increased hardness and chemical resistance. Thus, the corrosion and wear resistance are generally improved. The coatings are also electrically isolating and may serve decorative purposes. Applying a time-variant, dynamic electrical process control by pulse-current or current-steps is a promising approach to improve the coating properties, which is partially deployed in an industrial scale. In the present work, the influence of dynamic electrical process control on the coating properties is examined by means of a design of experiments (DOE). The effects of various electrolyte compositions and temperatures as well as processing time are considered with regard to coating thickness, hardness, wear resistance and the electrical energy consumption during the formation of the coatings. Information about the statistical significance of the effects of the parameters on the considered properties is obtained by an analysis of variance (ANOVA).

  2. Ideal anodization of silicon

    Energy Technology Data Exchange (ETDEWEB)

    Yamani, Z.; Thompson, W.H.; AbuHassan, L.; Nayfeh, M.H. [Department of Physics, University of Illinois at Urbana-Champaign, 1110 W. Green Street, Urbana, Illinois 61801 (United States)

    1997-06-01

    Silicon has been anodized such that the porous layer is passivated with a homogeneous stretching phase by incorporating H{sub 2}O{sub 2} in the anodization mixture. Fourier transform infrared spectroscopy measurements show that the Si{endash}H stretching mode oriented perpendicular to the surface at {approximately}2100cm{sup {minus}1} dominates the spectrum with negligible contribution from the bending modes in the 600{endash}900cm{sup {minus}1} region. Material analysis using Auger electron spectroscopy shows that the samples have very little impurities, and that the luminescent layer is very thin (5{endash}10 nm). Scanning electron microscopy shows that the surface is smoother with features smaller than those of conventional samples. {copyright} {ital 1997 American Institute of Physics.}

  3. Nanotubular structured Si-based multicomponent anodes for high-performance lithium-ion batteries with controllable pore size via coaxial electro-spinning.

    Science.gov (United States)

    Ryu, Jaegeon; Choi, Sinho; Bok, Taesoo; Park, Soojin

    2015-04-14

    We demonstrate a simple but straightforward process for the synthesis of nanotube-type Si-based multicomponents by combining a coaxial electrospinning technique and subsequent metallothermic reduction reaction. Si-based multicomponent anodes consisting of Si, alumina and titanium silicide show several advantages for high-performance lithium-ion batteries. Alumina and titanium silicide, which have high mechanical properties, act as an effective buffer layer for the large volume change of Si, resulting in outstanding volume suppression behavior (volume expansion of only 14%). Moreover, electrically conductive titanium silicide layers located at the inner and outer layers of a Si nanotube exhibit a high initial coulombic efficiency of 88.5% and an extraordinary rate capability. Nanotubular structured Si-based multicomponents with mechanically and electrically improved components can be used as a promising alternative to conventional graphite anode materials. This synthetic route can be extended to other high capacity lithium-ion battery anode materials.

  4. Dielectric Performance of a High Purity HTCC Alumina at High Temperatures - a Comparison Study with Other Polycrystalline Alumina

    Science.gov (United States)

    Chen, Liangyu

    2014-01-01

    A very high purity (99.99+%) high temperature co-fired ceramic (HTCC) alumina has recently become commercially available. The raw material of this HTCC alumina is very different from conventional HTCC alumina, and more importantly there is no glass additive in this alumina material for co-firing processing. Previously, selected HTCC and LTCC (low temperature co-fired ceramic) alumina materials were evaluated at high temperatures as dielectric and compared to a regularly sintered 96% polycrystalline alumina (96% Al2O3), where 96% alumina was used as the benchmark. A prototype packaging system based on regular 96% alumina with Au thickfilm metallization successfully facilitated long term testing of high temperature silicon carbide (SiC) electronic devices for over 10,000 hours at 500 C. In order to evaluate this new high purity HTCC alumina for possible high temperature packaging applications, the dielectric properties of this HTCC alumina substrate were measured and compared with those of 96% alumina and a previously tested LTCC alumina from room temperature to 550 C at frequencies of 120 Hz, 1 KHz, 10 KHz, 100 KHz, and 1 MHz. A parallel-plate capacitive device with dielectric of the HTCC alumina and precious metal electrodes were used for measurements of the dielectric constant and dielectric loss of the co-fired alumina material in the temperature and frequency ranges. The capacitance and AC parallel conductance of the capacitive device were directly measured by an AC impedance meter, and the dielectric constant and parallel AC conductivity of the dielectric were calculated from the capacitance and conductance measurement results. The temperature and frequency dependent dielectric constant, AC conductivity, and dissipation factor of the HTCC alumina substrate are presented and compared to those of 96% alumina and a selected LTCC alumina. Other technical advantages of this new co-fired material for possible high packaging applications are also discussed.

  5. High quality 3D shapes by silicon anodization

    Energy Technology Data Exchange (ETDEWEB)

    Ivanov, Alexey; Kovacs, Andras; Mescheder, Ulrich [Institute for Applied Research and Faculty of Computer and Electrical Engineering, Hochschule Furtwangen University, Robert-Gerwig-Platz 1, 78120 Furtwangen (Germany)

    2011-06-15

    In this paper some process considerations and optimizations of anodization for three-dimensional (3D)-structuring of silicon are discussed. For the shape controlling of etched form different approaches, such as frontside masking design, local backside doping and surface pre-structuring are presented. Influences of the opening size and etch depth on the shape of the etching form are investigated. The surface quality of the resulting 3D structures is critically dependent on the specific process parameters and process flow. Best surface quality was obtained for electropolishing in 7 wt.% hydrofluoric acid (HF) at applied current densities of 100-300 mA/cm{sup 2}. Application of 3D silicon forms for injection moulding is demonstrated and further implementations of the process for optical and fluidic devices are discussed. 3D silicon shapes fabricated using anodization process with local backside doping design. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  6. Challenges and Strategies in the Synthesis of Mesoporous Alumina Powders and Hierarchical Alumina Monoliths

    Directory of Open Access Journals (Sweden)

    Anne Galarneau

    2012-02-01

    Full Text Available A new rapid, very simple and one-step sol-gel strategy for the large-scale preparation of highly porous γ-Al2O3 is presented. The resulting mesoporous alumina materials feature high surface areas (400 m2 g−1, large pore volumes (0.8 mL g−1 and the ��-Al2O3 phase is obtained at low temperature (500 °C. The main advantages and drawbacks of different preparations of mesoporous alumina materials exhibiting high specific surface areas and large pore volumes such as surfactant-nanostructured alumina, sol-gel methods and hierarchically macro-/mesoporous alumina monoliths have been analyzed and compared. The most reproducible synthesis of mesoporous alumina are given. Evaporation-Induced Self-Assembly (EISA is the sole method to lead to nanostructured mesoporous alumina by direct templating, but it is a difficult method to scale-up. Alumina featuring macro- and mesoporosity in monolithic shape is a very promising material for in flow applications; an optimized synthesis is described.

  7. Contralateral tactile masking between forearms.

    Science.gov (United States)

    D'Amour, Sarah; Harris, Laurence R

    2014-03-01

    Masking effects have been demonstrated in which tactile sensitivity is affected when one touch is close to another on the body surface. Such effects are likely a result of local lateral inhibitory circuits that sharpen the spatial tuning of a given tactile receptor. Mutually inhibitory pathways have also been demonstrated between cortical tactile maps of the two halves of the body. Occasional reports have indicated that touches on one hand or forearm can affect tactile sensitivity at contralateral locations. Here, we measure the spatial tuning and effect of posture on this contralateral masking effect. Tactile sensitivity was measured on one forearm, while vibrotactile masking stimulation was applied to the opposite arm. Results were compared to sensitivity while vibrotactile stimulation was applied to a control site on the right shoulder. Sensitivity on the forearm was reduced by over 3 dB when the arms were touching and by 0.52 dB when they were held parallel. The masking effect depended on the position of the masking stimulus. Its effectiveness fell off by 1 STD when the stimulus was 29 % of arm length from the corresponding contralateral point. This long-range inhibitory effect in the tactile system suggests a surprisingly intimate relationship between the two sides of the body.

  8. Self-Rescue Mask Training

    CERN Multimedia

    2013-01-01

    Nine new self-rescue mask instructors have been trained since early 2013, which provides CERN with a total of 26 self-rescue mask instructors to date. This will allow us to meet the increasing training needs caused by the Long Shut Down LS1.   The self-rescue mask instructors have trained 1650 persons in 2012 and about 500 persons since the beginning of the year on how to wear the masks properly. We thank all the instructors and all the persons that made this training possible. Please remember that the self-rescue masks training sessions are scheduled as follows: Basic course: Tuesday and Thursday mornings (2 sessions – 8.30 AM and 10.30 AM), duration:  1.30 hour, in French and English – registration via CERN online training catalogue – Course code 077Y00. Refresher training : Monday mornings (2 sessions – 8.30 AM and 10.30 AM), duration: 1.30 hour , in French and English – registration via CERN online training catalogue &...

  9. Synthesis and surface characterization of alumina-silica-zirconia nanocomposite ceramic fibres on aluminium at room temperature

    Energy Technology Data Exchange (ETDEWEB)

    Mubarak Ali, M., E-mail: masterscience2003@yahoo.co.in [Advanced Materials Research Laboratory, Department of Chemistry, Periyar University, Omalur Main Road, Salem 636 011, Tamil Nadu (India); Raj, V., E-mail: alaguraj2@rediffmail.com [Advanced Materials Research Laboratory, Department of Chemistry, Periyar University, Omalur Main Road, Salem 636 011, Tamil Nadu (India)

    2010-04-01

    Alumina-silica-zirconia nanocomposite (ASZNC) ceramic fibres were synthesized by conventional anodization route. Scanning Electron Microscopy (SEM), Atomic Force microscopy (AFM), X-Ray Diffraction (XRD) and Energy Dispersive X-Ray spectroscopy (EDAX) were used to characterize the morphology and crystalloid structure of ASZNC fibres. Current density (DC) is one of the important parameters to get the alumina-silica-zirconia nanocomposite (ASZNC) ceramic fibres by this route. Annealing of the films exhibited a drastic change in the properties due to improved crystallinity. The root mean square roughness of the sample observed from atomic force microscopic analysis is about 71.5 nm which is comparable to the average grain size of the coatings which is about 72 nm obtained from X-Ray diffraction. The results indicate that, the ASZNC fibres are arranged well in the nanostructure. The thickness of the coating increased with the anodizing time, but the coatings turned rougher and more porous. At the initial stage the growth of ceramic coating increases inwards to the metal substrate and outwards to the coating surface simultaneously. Subsequently, it mainly grows towards the metal substrate and the density of the ceramic coating increases gradually, which results in the decrease of the total thickness as anodizing time increases. This new approach of preparing ASZNC ceramic fibres may be important in applications ranging from gas sensors to various engineering materials.

  10. Growth Mechanism of γ-MnS Nanorod-Arrays by Hydrothermal Method on Anodic Aluminum Oxide Template

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Jianming; Liu, Weifeng; Lv, Yong; Yao, Lianzeng [Chinese Academy of Science, Hefei, Anhui (China)

    2010-09-15

    Hydrothermal method is a general, low-cost and convenience method which was utilized for synthesis of nanomaterials. Our research group has reported that oriented MnS nanorods on anodic aluminum oxide template were synthesized under a hydrothermal condition and demonstrated the effect of precursor content on the morphology evolution of as-samples. In order to research the growth mechanism of the arrays, herein we synthesized MnS nanorod arrays by combination of anodic aluminum oxide template and hydrothermal method on different substrates. Through-hole anodic aluminum oxide templates were prepared using Al foil (99.999%) via a two-step anodization process as described in literature. To investigate the effect of different substrates on the morphology of the-products, different substrates including anodic aluminum oxide template (sample A), one-step anodization Al foil (sample B, which was prepared by first anodizing Al foil for 10h and then removing the alumina layer with the mixed acid (0.6 M H{sub 3}PO{sub 4} and 0.15 M H{sub 2}CrO{sub 4}), where the foil still kept the close-packed concave nano-pits consistently with the nanopole of anodic aluminum oxide template), Al foil (sample C, dipped in HNO{sub 3} solution and covered by a compact alumina layer), Si wafer (sample D) respectively were put into Teflon-lined stainless steel autoclaves of 20 mL capacity filled with 16 mL mixed solution consisting of 2 mol/L MnCl{sub 4} and 2 mol/L thiourea. We kept the reaction at 150 .deg. C for 20 h. When reactions completed the products were washed three times with distilled water and absolute ethanol, respectively. Then the products were dried in an oven at 60 .deg. C.

  11. Facile method for modulating the profiles and periods of self-ordered three-dimensional alumina taper-nanopores.

    Science.gov (United States)

    Li, Juan; Li, Congshan; Chen, Cheng; Hao, Qingli; Wang, Zhijia; Zhu, Jie; Gao, Xuefeng

    2012-10-24

    We report a facile nanofabrication method, one-step hard anodizing and etching peeling (OS-HA-EP) of aluminum foils followed by multistep mild anodizing and etching pore-widening (MS-MA-EW), for the controllable tailoring of hexagonally packed three-dimensional alumina taper-nanopores. Their profiles can be precisely tailored by the synergistic control of anodizing time, etching time and cyclic times at the MS-MA-EW stage, exemplified by linear cones, whorl-embedded cones, funnels, pencils, parabolas, and trumpets. Meantime, their periods can also be modulated in the range of 70-370 nm by choosing matched anodizing electrolytes (e.g., H(2)C(2)O(4), H(2)SO(4), H(2)C(2)O(4)-H(2)SO(4), and H(2)C(2)O(4)-C(2)H(5)OH mixture) and anodizing voltages at the OS-HA-EP stage. We also demonstrated that the long-range ordering of nanopits and the peak voltage of stable self-ordered HA, which are unachievable in a single H(2)C(2)O(4) electrolyte system, can be effectively tuned by simply adding tiny quantity of H(2)SO(4) and C(2)H(5)OH to keep an appropriate HA current density, respectively. This method of using the combination of simple pure chemical nanofabrication technologies is very facile and efficient in realizing the controllable tailoring of large-area alumina membranes containing self-ordered taper-nanopores. Our work opens a door for exploring the novel physical and chemical properties of different materials of nanotaper arrays.

  12. Synthesis and characterization of alumina precursor and alumina to be used as nano composite; Sintese e caracterizacao de precursores de alumina e alumina para uso em nanocompositos

    Energy Technology Data Exchange (ETDEWEB)

    Antunes, M.L.P., E-mail: malu@sorocaba.unesp.b [Universidade Estadual Paulista Julio de Mesquita Filho (UNESP), Sorocaba, SP (Brazil); Santos, H. Souza [Universidade de Sao Paulo (IF/USP), SP (Brazil). Inst. de Fisica; Santos, P. Souza [Universidade de Sao Paulo (EP/USP), SP (Brazil). Escola Politecnica

    2009-07-01

    With the evolution of nanomaterials technology, mainly in the 90s, it was possible to observe produced composites with alumina matrix and nanomaterial as reinforcing materials. It results in a significant improvement of mechanical proprieties of these composites. Thenceforth the study of synthesis and characterization of nanostructured materials has attracted great scientific interest. In this perspective, the aim of this work is to present an experimental procedure to obtain nordstrandite (aluminum hydroxide) with nanometric dimensions. Nordstrandite synthesis, obtained by the reaction of slightly amalgamated aluminum foil with aqueous ethylene glycol, which allows the control of the size of crystal produced. This control could be confirmed by X-Ray Diffraction and Electron Microscopy. Thermal transformation study is also presented. This study allowed the identification of transition aluminas that have potential to produce nanometric aluminas. (author)

  13. Dynamical Mechanical Properties for AD90 Alumina

    Institute of Scientific and Technical Information of China (English)

    REN Hui-lan; NING Jian-guo; LI Ping

    2007-01-01

    The dynamic response of polycrystalline alumina was investigated in the pressure range of 0 -13 GPa by planar impact experiments.Velocity interferometer system for any reflector(VISAR) was used to obtain free surface velocity profile and determine the Hugoniot elastic limit,and manganin gauges were employed to obtain the stress-time histories and determine Hugoniot curve.Both the free surface particle velocity profiles and Hugoniot curves indicate the dispersion of the "plastic" wave for alumina.With the measured stress histories,the complete histories of strain,particle velocity,specific volume and specific internal energy are gained by using path line principle of Lagrange analysis.The dynamic mechanical behaviors for alumina under impact loading are analyzed,such as nonlinear characteristic,strain rate dependence,dispersion and declination of shock wave in the material.

  14. Role of aluminum doping on phase transformations in nanoporous titania anodic oxides

    Energy Technology Data Exchange (ETDEWEB)

    Bayata, Fatma [Istanbul Bilgi University, Department of Mechanical Engineering, 34060, Eyup, Istanbul (Turkey); Ürgen, Mustafa, E-mail: urgen@itu.edu.tr [Istanbul Technical University, Department of Metallurgical and Materials Engineering, 34469, Maslak, Istanbul (Turkey)

    2015-10-15

    The role of aluminium doping on anatase to rutile phase transformation of nanoporous titanium oxide films were investigated. For this purpose pure and aluminum doped metal films were deposited on alumina substrates by cathodic arc physical deposition. The nanoporous anodic oxides were prepared by porous anodizing of pure and aluminum doped titanium metallic films in an ethylene glycol + NH{sub 4}F based electrolyte. Nanoporous amorphous structures with 60–80 nm diameter and 2–4 μm length were formed on the surfaces of alumina substrates. The amorphous undoped and Al-doped TiO{sub 2} anodic oxides were heat-treated at different temperatures in the range of 280–720 °C for the investigation of their crystallization behavior. The combined effects of nanoporous structure and Al doping on crystallization behavior of titania were investigated using X-ray diffraction (XRD) and micro Raman analysis. The results indicated that both Al ions incorporated into the TiO{sub 2} structure and the nanoporous structure retarded the rutile formation. It was also revealed that presence or absence of metallic film underneath the nanopores has a major contribution to anatase-rutile transformation. - Highlights: • Al-doped TiO{sub 2} nanopores were grown on alumina substrates using anodization method. • The crystallization behavior of nanoporous Al-doped TiO{sub 2} were investigated. • Al doping into nanoporous TiO{sub 2} retarded the anatase-rutile transformation. • Nanostructuring has significant role in controlling rutile formation temperature. • The absence of the metallic film under the nanopores delayed the rutile formation.

  15. Liquid-Metal Electrode to Enable Ultra-Low Temperature Sodium-Beta Alumina Batteries for Renewable Energy Storage

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Xiaochuan; Li, Guosheng; Kim, Jin Yong; Mei, Donghai; Lemmon, John P.; Sprenkle, Vincent L.; Liu, Jun

    2014-08-01

    Metal electrodes have a high capacity for energy storage but have found limited applications in batteries because of dendrite formation and other problems. In this paper, we report a new alloying strategy that can significantly reduce the melting temperature and improve wetting with the electrolyte to allow the use of liquid metal as anode in sodium-beta alumina batteries (NBBs) at much lower temperatures (e.g., 95 to 175°C). Commercial NBBs such as sodium-sulfur (Na-S) battery and sodium-metal halide (ZEBRA) batteries typically operate at relatively high temperatures (e.g., 300-350°C) due to poor wettability of sodium on the surface of β"-Al2O3. Our combined experimental and computational studies suggest that Na-Cs alloy can replace pure sodium as the anode material, which provides a significant improvement in wettability, particularly at lower temperatures (i.e., <200°C). Single cells with the Na-Cs alloy anode exhibit excellent cycling life over those with pure sodium anode at 175 and 150°C. The cells can even operate at 95°C, which is below the melting temperature of pure sodium. These results demonstrate that NBB can be operated at ultra lower temperatures with successfully solving the wetting issue. This work also suggests a new strategy to use liquid metal as the electrode materials for advanced batteries that can avoid the intrinsic safety issues associated with dendrite formation on the anode.

  16. The fabrication of high sensitivity gold nanorod H2S gas sensors utilizing the highly uniform anodic aluminum oxide template

    Directory of Open Access Journals (Sweden)

    Chien-Yu Li

    2016-12-01

    Full Text Available Gold nanorod were fabricated using anodic alumina oxide template for H2S gas detection. The nanorod gas sensor exhibits high surface density and contact area, which can increase detection sensitivity. The anodic alumina oxide template contains an array of pores, with a width of 70 nm and a length of 27μm. Au nanorod were obtained through electro-deposition under a pulse bias of −1 V. The resistance of the Au nanorod was recorded upon exposure to various concentrations of H2S. The resistance could be attributed to the high electron affinity between sulfide and Au nanorod. Au–sulfide bonds provide strong bonding, which could alter the conductivity of the sensor. The gas sensor exhibits high sensitivity and short response time for H2S detection at room temperature.

  17. The fabrication of high sensitivity gold nanorod H2S gas sensors utilizing the highly uniform anodic aluminum oxide template

    Science.gov (United States)

    Li, Chien-Yu; Li, Ciao-Yu; Wu, You-Lin; Hsu, Chung-Ping; Lee, Ming-Ching; Houng, Mau-Phon

    2016-12-01

    Gold nanorod were fabricated using anodic alumina oxide template for H2S gas detection. The nanorod gas sensor exhibits high surface density and contact area, which can increase detection sensitivity. The anodic alumina oxide template contains an array of pores, with a width of 70 nm and a length of 27 μ m . Au nanorod were obtained through electro-deposition under a pulse bias of -1 V. The resistance of the Au nanorod was recorded upon exposure to various concentrations of H2S. The resistance could be attributed to the high electron affinity between sulfide and Au nanorod. Au-sulfide bonds provide strong bonding, which could alter the conductivity of the sensor. The gas sensor exhibits high sensitivity and short response time for H2S detection at room temperature.

  18. A Novel Processing Route for Ni-doped Alumina Composites

    Institute of Scientific and Technical Information of China (English)

    JING Mao-xiang; SHEN Xiang-qian; ZHOU Jian-xin; LI Dong-hong; LI Wang-xing

    2006-01-01

    Alumina-based composites containing 0-15wt% Ni metallic phase were produced by hot press-sintering Ni-coated alumina powders. The Ni-coated alumina powders were prepared by the aqueous heterogeneous precipitation of alumina micro-powders and nickel sulfate salt followed by reduction process. The microstructural features and dispersion of Ni phase in Ni-coated alumina powders and the subsequent alumina-Ni cermets were investigated using scanning electron microscope (SEM), X-ray diffractometer (XRD), and transmission electron microscope (TEM). The relative density of the hot press-sintered composites was measured with the Archimedes' method while the fracture strength and the fracture toughness were defined with the three-point bending method and the micro-indentation fracture method. In the formation of alumina-Ni cermets from sintered Ni-coated alumina powders, Ni phase to some extent limits the densification rate and stifles the coarsening and growing process of alumina grains. The Ni phase is found to be located at the interfaces and the triple-joint junctions of alumina grains which results into alteration of the fracture mode of alumina and its increased fracture strength and fracture toughness if compared with monolithic alumina.

  19. Tribological properties of nanoscale alumina-zirconia composites

    NARCIS (Netherlands)

    Kerkwijk, B.; Winnubst, A.J.A.; Verweij, H.; Mulder, E.J.; Metselaar, H.S.C.; Schipper, D.J.

    1999-01-01

    The tribological properties of zirconia (Y-TZP), alumina and their composites, alumina dispersed in zirconia (ADZ) and zirconia-toughened alumina (ZTA), were investigated. These ceramics are made by colloidal processing methods such that well-defined, homogeneous microstructures with submicron grain

  20. Microwave fast sintering of submicrometer alumina

    Directory of Open Access Journals (Sweden)

    Romualdo Rodrigues Menezes

    2010-09-01

    Full Text Available Commercially available alumina powder with high-purity submicrometer particle size and narrow particle size distribution was fully densified by a microwave hybrid fast firing technique. The alumina compacts were surrounded by susceptor material, which helped the heating of the samples, and sintered in a microwave oven at a frequency of 2.45 GHz and a power level of 1.8 kW. The sintered samples reached densities of 99% in sintering cycles of 30 to 40 minutes, a much shorter time than conventional sintering processes. The sintered samples showed uniform microstructures with powder particle size/average grain size rations higher than 1:2.

  1. Production mask composition checking flow

    Science.gov (United States)

    Ma, Shou-Yuan; Yang, Chuen-Huei; Tsai, Joe; Wang, Alice; Lin, Roger; Lee, Rachel; Deng, Erwin; Lin, Ling-Chieh; Liao, Hung-Yueh; Tsai, Jenny; Bowhill, Amanda; Vu, Hien; Russell, Gordon

    2016-05-01

    The mask composition checking flow is an evolution of the traditional mask rule check (MRC). In order to differentiate the flow from MRC, we call it Mask Data Correctness Check (MDCC). The mask house does MRC only to identify process limitations including writing, etching, metrology, etc. There still exist many potential errors that could occur when the frame, main circuit and dummies all together form a whole reticle. The MDCC flow combines the design rule check (DRC) and MRC concepts to adapt to the complex patterns in today's wafer production technologies. Although photomask data has unique characteristics, the MRC tool in Calibre® MDP can easily achieve mask composition by using the Extended MEBES job deck (EJB) format. In EJB format, we can customize the combination of any input layers in an IC design layout format, such as OASIS. Calibre MDP provides section-based processing for many standard verification rule format (SVRF) commands that support DRC-like checks on mask data. Integrating DRC-like checking with EJB for layer composition, we actually perform reticle-level DRC, which is the essence of MDCC. The flow also provides an early review environment before the photomask pattern files are available. Furthermore, to incorporate the MDCC in our production flow, runtime is one of the most important indexes we consider. When the MDCC is included in the tape-out flow, the runtime impact is very limited. Calibre, with its multi-threaded processes and good scalability, is the key to achieving acceptable runtime. In this paper, we present real case runtime data for 28nm and 14nm technology nodes, and prove the practicability of placing MDCC into mass production.

  2. Masked Hypertension in Diabetes Mellitus

    Science.gov (United States)

    Franklin, Stanley S.; Thijs, Lutgarde; Li, Yan; Hansen, Tine W.; Boggia, José; Liu, Yanping; Asayama, Kei; Björklund-Bodegård, Kristina; Ohkubo, Takayoshi; Jeppesen, Jørgen; Torp-Pedersen, Christian; Dolan, Eamon; Kuznetsova, Tatiana; Stolarz-Skrzypek, Katarzyna; Tikhonoff, Valérie; Malyutina, Sofia; Casiglia, Edoardo; Nikitin, Yuri; Lind, Lars; Sandoya, Edgardo; Kawecka-Jaszcz, Kalina; Filipovský, Jan; Imai, Yutaka; Wang, Jiguang; Ibsen, Hans; O’Brien, Eoin; Staessen, Jan A.

    2013-01-01

    Although distinguishing features of masked hypertension in diabetics are well known, the significance of antihypertensive treatment on clinical practice decisions has not been fully explored. We analyzed 9691 subjects from the population-based 11-country International Database on Ambulatory Blood Pressure in Relation to Cardiovascular Outcomes. Prevalence of masked hypertension in untreated normotensive participants was higher (Phypertensives tended to be higher than in normotensives (hazard rate [HR], 1.96; 95% confidence interval [CI], 0.97–3.97; P=0.059), similar to untreated stage 1 hypertensives (HR, 1.07; CI, 0.58–1.98; P=0.82), but less than stage 2 hypertensives (HR, 0.53; CI, 0.29–0.99; P=0.048). In contrast, cardiovascular risk was not significantly different in antihypertensive-treated diabetic-masked hypertensives, as compared with the normotensive comparator group (HR, 1.13; CI, 0.54–2.35; P=0.75), stage 1 hypertensives (HR, 0.91; CI, 0.49–1.69; P=0.76), and stage 2 hypertensives (HR, 0.65; CI, 0.35–1.20; P=0.17). In the untreated diabetic-masked hypertensive population, mean conventional systolic/diastolic blood pressure was 129.2±8.0/76.0±7.3 mm Hg, and mean daytime systolic/diastolic blood pressure 141.5±9.1/83.7±6.5 mm Hg. In conclusion, masked hypertension occurred in 29% of untreated diabetics, had comparable cardiovascular risk as stage 1 hypertension, and would require considerable reduction in conventional blood pressure to reach daytime ambulatory treatment goal. Importantly, many hypertensive diabetics when receiving antihypertensive therapy can present with normalized conventional and elevated ambulatory blood pressure that mimics masked hypertension. PMID:23478096

  3. Informational masking and musical training.

    Science.gov (United States)

    Oxenham, Andrew J; Fligor, Brian J; Mason, Christine R; Kidd, Gerald

    2003-09-01

    The relationship between musical training and informational masking was studied for 24 young adult listeners with normal hearing. The listeners were divided into two groups based on musical training. In one group, the listeners had little or no musical training; the other group was comprised of highly trained, currently active musicians. The hypothesis was that musicians may be less susceptible to informational masking, which is thought to reflect central, rather than peripheral, limitations on the processing of sound. Masked thresholds were measured in two conditions, similar to those used by Kidd et al. [J. Acoust. Soc. Am. 95, 3475-3480 (1994)]. In both conditions the signal was comprised of a series of repeated tone bursts at 1 kHz. The masker was comprised of a series of multitone bursts, gated with the signal. In one condition the frequencies of the masker were selected randomly for each burst; in the other condition the masker frequencies were selected randomly for the first burst of each interval and then remained constant throughout the interval. The difference in thresholds between the two conditions was taken as a measure of informational masking. Frequency selectivity, using the notched-noise method, was also estimated in the two groups. The results showed no difference in frequency selectivity between the two groups, but showed a large and significant difference in the amount of informational masking between musically trained and untrained listeners. This informational masking task, which requires no knowledge specific to musical training (such as note or interval names) and is generally not susceptible to systematic short- or medium-term training effects, may provide a basis for further studies of analytic listening abilities in different populations.

  4. Study of the molybdenum retention in alumina; Estudio de la retencion de molibdeno en alumina

    Energy Technology Data Exchange (ETDEWEB)

    Wilkinson, Maria V.; Mondino, Angel V.; Manzini, Alberto [Comision Nacional de Energia Atomica, Buenos Aires (Argentina). Centro Atomico Ezeiza. Radioquimica y Quimica de las Radiaciones

    2002-07-01

    The Argentine National Atomic Energy Commission routinely produces {sup 99} Mo by fission of highly enriched uranium contained in targets irradiated in RA-3 reactor. The current process begins with the dissolution of the irradiated target in a basic media, considering the possibility of changing the targets, it could be convenient to dissolve them in acid media. The use of alumina as a first separation step in acid dissolution processes is already known although it is necessary to determine both the type of alumina to be used and the separation conditions. The study of molybdenum retention in alumina was performed at laboratory scale, using Mo-99 as radiotracer. Different kinds of alumina were tried, varying charge solution acidity. Influence of uranium concentration in the loading solution on molybdenum retention was also studied. (author)

  5. Third-generation alumina-on-alumina ceramic bearings in cementless total hip arthroplasty.

    Science.gov (United States)

    Lusty, P J; Tai, C C; Sew-Hoy, R P; Walter, W L; Walter, W K; Zicat, B A

    2007-12-01

    Wear debris has been implicated in the pathogenesis of osteolysis. Alumina-on-alumina ceramic bearings have a low wear rate, which may reduce the prevalence of osteolysis. The purpose of this study was to determine the rates of wear and osteolysis associated with modern cementless hip arthroplasty with alumina-on-alumina bearings at five years. We analyzed a series of 301 third-generation alumina-on-alumina cementless primary total hip replacements in 283 patients. The average age of the patients at the time of the arthroplasty was fifty-eight years. All procedures were performed with use of the same surgical technique and the same implant at a single center. At a minimum of five years postoperatively, ten patients had died and twenty-two patients were lost to follow-up. We assessed patients clinically and radiographically, and all retrieved bearings were analyzed for wear. At the time of the latest follow-up, the mean Harris hip score was 95 points. All surviving implants had radiographic evidence of stable bone ingrowth. There were nine revisions of one or both components. Four stems were revised following periprosthetic fracture, one stem was revised because of aseptic loosening at two months, and one stem was revised to facilitate a femoral shortening osteotomy. Two cups were revised because of psoas tendinitis, and both components of one arthroplasty were revised because of impingement and osteolysis. The rate of survival of both components, with revision because of aseptic loosening or osteolysis as the end point, was 99% at seven years. The retrieved femoral heads showed an early median wear rate of 0.2 mm(3) per year. Cementless primary total hip prostheses with a third-generation alumina-on-alumina bearing showed very low wear and were associated with minimal osteolysis at the time of follow-up, at a minimum of five years.

  6. LOW TEMPERATURE SINTERING OF ALUMINA BIOCERAMIC UNDER NORMAL PRESSURE

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Superfine alumina powder with high purity (mean particle size is less than 0. 35μm) were used as main starting material for sintering alumina ceramic. A multiple additive MgO-ZrO2 (Y2O3) was homogeneously added into the batch by the chemical coprecipitation method. Sintering of alumina bioceramic at low tempera ture (<1600C) was achieved resulting in a dense and high strength alumina ceramic with the bending strength up to 382 MPa and an improved fracture toughness. Mechanism that the multiple additives promote the sintering of alumina ceramic is discussed on the base of XRD and SEM analysis.

  7. Thermal Conductivity of Alumina-Toughened Zirconia Composites

    Science.gov (United States)

    Bansal, Narottam P.; Zhu, Dong-Ming

    2003-01-01

    10-mol% yttria-stabilized zirconia (10YSZ)-alumina composites containing 0 to 30 mol% alumina were fabricated by hot pressing at 1500 C in vacuum. Thermal conductivity of the composites, determined at various temperatures using a steady-state laser heat flux technique, increased with increase in alumina content. Composites containing 0, 5, and 10-mol% alumina did not show any change in thermal conductivity with temperature. However, those containing 20 and 30-mol% alumina showed a decrease in thermal conductivity with increase in temperature. The measured values of thermal conductivity were in good agreement with those calculated from simple rule of mixtures.

  8. Thin flexible intercalation anodes

    Energy Technology Data Exchange (ETDEWEB)

    Levy, S.C.; Cieslak, W.R.; Klassen, S.E.; Lagasse, R.R.

    1994-10-01

    Poly(acrylonitrile) fibers have been pyrolyzed under various conditions to form flexible carbon yarns capable of intercalating lithium ions. These fibers have also been formed into both woven and non woven cloths. Potentiostatic, potentiodynamic and galvanostatic tests have been conducted with these materials in several electrolytes. In some tests, a potential hold was used after each constant current charge and discharge. These tests have shown some of these flexible materials to reversibly intercalate lithium ions to levels that are suitable for use as a practical battery anode.

  9. Anodic bonded graphene

    Science.gov (United States)

    Balan, Adrian; Kumar, Rakesh; Boukhicha, Mohamed; Beyssac, Olivier; Bouillard, Jean-Claude; Taverna, Dario; Sacks, William; Marangolo, Massimiliano; Lacaze, Emanuelle; Gohler, Roger; Escoffier, Walter; Poumirol, Jean-Marie; Shukla, Abhay

    2010-09-01

    We show how to prepare graphene samples on a glass substrate with the anodic bonding method. In this method, a graphite precursor in flake form is bonded to a glass substrate with the help of an electrostatic field and then cleaved off to leave few layer graphene on the substrate. Now that several methods are available for producing graphene, the relevance of our method is in its simplicity and practicality for producing graphene samples of about 100 µm lateral dimensions. This method is also extensible to other layered materials. We discuss some detailed aspects of the fabrication and results from Raman spectroscopy, local probe microscopy and transport measurements on these samples.

  10. Anodic bonded graphene

    Energy Technology Data Exchange (ETDEWEB)

    Balan, Adrian; Kumar, Rakesh; Boukhicha, Mohamed; Beyssac, Olivier; Bouillard, Jean-Claude; Taverna, Dario; Sacks, William; Shukla, Abhay [Universite Pierre et Marie Curie-Paris 6, CNRS-UMR7590, Institut de Mineralogie et de Physique des Milieux Condenses, 140 rue de Lourmel, Paris, F-75015 France (France); Marangolo, Massimiliano; Lacaze, Emanuelle; Gohler, Roger [Universite Pierre et Marie Curie-Paris 6, CNRS-UMR7588, Institut des Nanosciences de Paris, 140 rue de Lourmel, Paris, F-75015 France (France); Escoffier, Walter; Poumirol, Jean-Marie, E-mail: abhay.shukla@upmc.f [Laboratoire National des Champs Magnetiques Intenses, INSA UPS CNRS, UPR 3228, Universite de Toulouse, 143 avenue de Rangueil, 31400 Toulouse (France)

    2010-09-22

    We show how to prepare graphene samples on a glass substrate with the anodic bonding method. In this method, a graphite precursor in flake form is bonded to a glass substrate with the help of an electrostatic field and then cleaved off to leave few layer graphene on the substrate. Now that several methods are available for producing graphene, the relevance of our method is in its simplicity and practicality for producing graphene samples of about 100 {mu}m lateral dimensions. This method is also extensible to other layered materials. We discuss some detailed aspects of the fabrication and results from Raman spectroscopy, local probe microscopy and transport measurements on these samples.

  11. Stabilization of Self-Assembled Alumina Mesophases

    NARCIS (Netherlands)

    Perez, Lidia Lopez; Perdriau, Sebastien; ten Brink, Gert; Kooi, Bart J.; Heeres, Hero Jan; Melian-Cabrera, Ignacio

    2013-01-01

    An efficient route to stabilize alumina mesophases derived from evaporation-induced self-assembly is reported after investigating various aspects in-depth: influence of the solvent (EtOH, s-BuOH, and t-BuOH) on the textural and structural properties of the mesophases based on aluminum

  12. Selective metallization of alumina by laser

    NARCIS (Netherlands)

    Shrivastva, P.B.; Boose, C.A.; Kolster, B.H.; Harteveld, C.; Meinders, B.

    1991-01-01

    Nickel has been selectively deposited on an alumina substrate without any pretreatment from a flow of a nickel acetate solution using the focused beam of an excimer laser. Nickel spots as well as nickel lines were drawn and subsequently plated with an electroless Ni-B coating. Excellent adhesion of

  13. Stabilization of Self-Assembled Alumina Mesophases

    NARCIS (Netherlands)

    Perez, Lidia Lopez; Perdriau, Sebastien; ten Brink, Gert; Kooi, Bart J.; Heeres, Hero Jan; Melian-Cabrera, Ignacio

    2013-01-01

    An efficient route to stabilize alumina mesophases derived from evaporation-induced self-assembly is reported after investigating various aspects in-depth: influence of the solvent (EtOH, s-BuOH, and t-BuOH) on the textural and structural properties of the mesophases based on aluminum tri-sec-butoxi

  14. alumina phase transformation from thermal decomposition of ...

    African Journals Online (AJOL)

    HOD

    INTRODUCTION. Alumina is one of the major components used as catalyst support ... used for processing petroleum, gas, petrochemicals and for other ... The extent and total conversion to the corundum ... purification, vegetable glues, porcelain cements, natural deodorant ..... Catalyst in Steam Reforming of Dimethyl ether:.

  15. "The Mask Who Wasn't There": Visual Masking Effect with the Perceptual Absence of the Mask

    Science.gov (United States)

    Rey, Amandine Eve; Riou, Benoit; Muller, Dominique; Dabic, Stéphanie; Versace, Rémy

    2015-01-01

    Does a visual mask need to be perceptually present to disrupt processing? In the present research, we proposed to explore the link between perceptual and memory mechanisms by demonstrating that a typical sensory phenomenon (visual masking) can be replicated at a memory level. Experiment 1 highlighted an interference effect of a visual mask on the…

  16. Dielectric Performance of High Purity HTCC Alumina at High Temperatures - A Comparison Study with Other Polycrystalline Alumina

    Science.gov (United States)

    Chen, Liang-Yu

    2012-01-01

    A very high purity (99.99+) high temperature co-fired ceramic (HTCC) alumina has recently become commercially available. The raw material of this HTCC alumina is very different from conventional HTCC alumina, and more importantly there is no glass additive in this co-fired material. Previously, selected HTCC and LTCC (low temperature co-fired ceramic) alumina materials were evaluated at high temperatures as dielectric and compared to a regularly sintered 96 polycrystalline alumina (96 Al2O3), where 96 alumina was used as the benchmark. A prototype packaging system based on regular 96 alumina with Au thick-film metallization successfully facilitated long term testing of high temperature silicon carbide (SiC) electronic devices for over 10,000 hours at 500C. In order to evaluate this new HTCC alumina for possible high temperature packaging applications, the dielectric properties of this HTCC alumina substrate were measured and compared with those of 96 alumina and a LTCC alumina from room temperature to 550C at frequencies of 120 Hz, 1 KHz, 10 KHz, 100 KHz, and 1 MHz. A parallel-plate capacitive device with dielectric of the HTCC alumina and precious metal electrodes were used for measurements of the dielectric constant and dielectric loss of the co-fired alumina material in the temperature and frequency ranges. The capacitance and AC parallel conductance of the capacitive device were directly measured by an AC impedance meter, and the dielectric constant and parallel AC conductivity of the dielectric were calculated from the capacitance and conductance measurement results. The temperature and frequency dependent dielectric constant, AC conductivity, and dissipation factor of the HTCC alumina substrate are presented and compared to those of 96 alumina. Other technical advantages of this new co-fired material for possible high packaging applications are also discussed.

  17. MECHANICAL BEHAVIOUR OF ALUMINA-ZIRCONIA COMPOSITE BY SLURRY METHOD

    Directory of Open Access Journals (Sweden)

    JYOTI PRAKASH

    2011-02-01

    Full Text Available Alumina has got some excellent properties like chemical inertness, thermal and mechanical strength against hazardous environment. Alumina is a good ceramic material which is being used for structuralapplications. To enhance the toughness and strength of the body some Zirconia is also used with it. The use of Zirconia in alumina is known as toughening of alumina. One difficulty arises, when alumina and alumina toughened composite are sintered , because the low sinterability of Alumina-Zirconia forced the compact to give very low density body. To overcome this problem alumina and alumina composites are made from slurry method which gives nearly theoretical density. The combined effect of alumina and Zirconia on the phase transformation and microstructure development of heat-treated Alumina-Zirconia composites has been studied. Slurry is prepared by adding water, dispersant, binder and anti-foaming agent. In the present study, Sintering schedule is optimized and kept constant for all samples. After sintering, mechanical behaviour of the composite has been studied.

  18. Surface modification of alumina nanoparticles with silane coupling agents

    Energy Technology Data Exchange (ETDEWEB)

    Prado, Luis A.S.A.; Sriyai, Montira; Ghislandi, Marcos; Schulte, Karl [Technische Universitaet Hamburg-Harburg, Hamburg (Germany). Inst. fuer Kunststoffe und Verbundwerkstoffe (M-11); Barros-Timmons, Ana [University of Aveiro (Portugal). Dept. of Chemistry. Centro de Investigacao em Materiais Ceramicos e Compositos (CICECO)

    2010-07-01

    In the present paper we describe the surface modification of alumina nanoparticles using epoxy-containing alkoxysilanes (silane coupling agents, SCA). The materials were characterized using infrared spectroscopy and solid-state nuclear magnetic resonance. Whereas, neat alumina nanoparticles could be expectedly modified with the afore mentioned SCA, as evidenced by {sup 13}C CPMAS NMR, the presence of arylsulphonates at the surface of alumina caused the ringopening polymerization of the epoxide. This polymerization reaction facilitated the surface modification of alumina by the SCA. X-ray powder diffraction and {sup 27}Al MAS NMR clearly demonstrated that in spite of the SCA polymerization, there were neither structural changes nor phase transitions in the alumina after the surface modification. The surface modification decreased the thermal stability of alumina, in comparison to pristine alumina nanoparticles. (author)

  19. Synthesis of alumina-α using aluminium acetate; Sintese de alumina-α utilizando acetato de aluminio

    Energy Technology Data Exchange (ETDEWEB)

    Cartaxo, J.M.; Galdino, M.N.; Neves, G.A., E-mail: lulianamelo25@gmail.com [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Unidade Academica de Engenharia de Materiais; Menezes, R.R.; Ferreira, H.S. [Universidade Federal da Paraiba (UFPB), Joao Pessoa, PB (Brazil). Departamento de Engenharia de Materiais

    2011-07-01

    In the face of great technological importance of alumina, this paper aims to synthesize the α-alumina using chemical activation from aluminum acetate. The synthesized powders were characterized by X-ray diffraction and thermal analysis. The results obtained proved the thermal decomposition of the precursor, as well as possible metastable phases of alumina before the phase transformation in α. There was also difficult to obtain α-alumina from aluminum acetate, on the other hand there was, comparatively, that the chemical activation accelerated the synthesis of α-alumina. (author)

  20. Degradation of alumina and zirconia toughened alumina (ZTA) hip prostheses tested under microseparation conditions in a shock device

    CERN Document Server

    Uribe, Juliana; Gremillard, Laurent; Reynard, Bruno

    2013-01-01

    This paper considers the degradation of alumina and zirconia toughened alumina vs. alumina for hip implants. The materials are as assumed to be load bearing surfaces subjected to shocks in wet conditions. The load is a peak of force; 9 kN was applied over 15 ms at 2 Hz for 800,000 cycles. The volumetric wear and roughness are lower for ZTA than for alumina. The long ZTA ageing did not seem to have a direct influence on the roughness. The ageing increased the wear volumes of ZTA and it was found to have a higher wear resistance compared to alumina.

  1. Mesoporous Silicon-Based Anodes

    Science.gov (United States)

    Peramunage, Dharmasena

    2015-01-01

    For high-capacity, high-performance lithium-ion batteries. A new high-capacity anode composite based on mesoporous silicon is being developed. With a structure that resembles a pseudo one-dimensional phase, the active anode material will accommodate significant volume changes expected upon alloying and dealloying with lithium (Li).

  2. Fabrication and optical properties of platinum nanowire arrays on anodic aluminium oxide templates

    Institute of Scientific and Technical Information of China (English)

    高铁仁; 陈子瑜; 彭勇; 李发伸

    2002-01-01

    Arrays of Pt nanowires, fabricated by electrodepositing Pt metal into nanoporous anodic aluminium oxide (AAO)templates, exhibit a preferable optical absorption band in the ultraviolet-visible (UV-VIS) spectra and present a blueshift as the wire aspect ratio increases or its radius decreases. This type of optical property of Pt nanowire/porous alumina composites has been theoretically explored using Maxwell-Garnett (MG) effective medium theory. The MG theory,however, is only applicable to nanowires with an infinitesimally small radius relative to the wavelength of an incident light. The nanowire radius is controlled by the pore radius of the host alumina, which depends on anodizing conditions such as the selected electrolyte, anodizing time, temperature and voltage. The nanowire aspect ratios depend on the amount of Pt deposited into the nanopores of AAO films. The optical absorption properties of the arrays of Pt nanowires with diameters of 24, 55 and 90nm have been investigated by the UV-VIS spectra, which show that the extinction maximum (λmax) shifts to shorter wavelength side as the wire aspect ratio increases or its radius decreases.The results are qualitatively consistent with those calculated based on the MG theory.

  3. 21 CFR 868.5580 - Oxygen mask.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Oxygen mask. 868.5580 Section 868.5580 Food and... ANESTHESIOLOGY DEVICES Therapeutic Devices § 868.5580 Oxygen mask. (a) Identification. An oxygen mask is a device placed over a patient's nose, mouth, or tracheostomy to administer oxygen or aerosols. (b)...

  4. Mask qualification strategies in a wafer fab

    Science.gov (United States)

    Jaehnert, Carmen; Kunowski, Angela

    2007-02-01

    Having consistent high quality photo masks is one of the key factors in lithography in the wafer fab. Combined with stable exposure- and resist processes, it ensures yield increases in production and fast learning cycles for technology development and design evaluation. Preventive controlling of incoming masks and quality monitoring while using the mask in production is essential for the fab to avoid yield loss or technical problems caused by mask issues, which eventually result in delivery problems to the customer. In this paper an overview of the procedures used for mask qualification and production release, for both logic and DRAM, at Infineon Dresden is presented. Incoming qualification procedures, such as specification checks, incoming inspection, and inline litho process window evaluation, are described here. Pinching and electrical tests, including compatibility tests for mask copies for high volume products on optimized litho processes, are also explained. To avoid mask degradation over lifetime, re-inspection checks are done for re-qualification while using the mask in production. The necessity of mask incoming inspection and re-qualification, due to the repeater printing from either the processing defects of the original mask or degrading defects of being used in the fab (i.e. haze, ESD, and moving particles, etc.), is demonstrated. The need and impact of tight mask specifications, such as CD uniformity signatures and corresponding electrical results, are shown with examples of mask-wafer CD correlation.

  5. Sinusoidal masks for single channel speech separation

    DEFF Research Database (Denmark)

    Mowlaee, Pejman; Christensen, Mads Græsbøll; Jensen, Søren Holdt

    2010-01-01

    In this paper we present a new approach for binary and soft masks used in single-channel speech separation. We present a novel approach called the sinusoidal mask (binary mask and Wiener filter) in a sinusoidal space. Theoretical analysis is presented for the proposed method, and we show...

  6. Electrochemical growth of ZnO nanowires inside nanoporous alumina templates. A comparison with metallic Zn nanowires growth

    Energy Technology Data Exchange (ETDEWEB)

    Ramirez, Daniel [Instituto de Quimica, Pontificia Universidad Catolica de Valparaiso, Valparaiso (Chile); Laboratoire d' Electrochimie et Chimie Analytique (UMR CNRS 7575), Ecole Nationale Superieure de Chimie de Paris (ENSCP) (France); Pauporte, Thierry; Lincot, Daniel [Laboratoire d' Electrochimie et Chimie Analytique (UMR CNRS 7575), Ecole Nationale Superieure de Chimie de Paris (ENSCP) (France); Gomez, Humberto [Instituto de Quimica, Pontificia Universidad Catolica de Valparaiso, Valparaiso (Chile)

    2008-10-15

    Molecular oxygen reduction in presence of Zn(II) allowed to get arrays of zinc oxide (ZnO) nanowires (NWs) inside thick anodic alumina membranes (AAM), previously made by anodization in oxalic acid. A Zinc (Zn) NWs array made by electrochemical deposition (ED) was employed as a metal reference in order to compare its growth behavior with respect to that of ZnO, a semiconducting material. Chronoamperometric measurements for Zn NWs showed a typical response for metallic growth inside porous templates while ZnO NWs did not show this behavior. We observed that Zn NWs grew faster than ZnO NWs as checked by the electrical charge. SEM images showed the presence of ZnO NWs only after long deposition time. X-ray diffraction data confirmed the ZnO structure. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  7. Graphene coated with alumina and its utilization as a thermal conductivity enhancer for alumina sphere/thermoplastic polyurethane composite

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Ki Tae; Dao, Trung Dung [Department of Chemistry, Energy Harvest-Storage Research Center, University of Ulsan, Ulsan 680-749 (Korea, Republic of); Jeong, Han Mo, E-mail: hmjeong@mail.ulsan.ac.kr [Department of Chemistry, Energy Harvest-Storage Research Center, University of Ulsan, Ulsan 680-749 (Korea, Republic of); Anjanapura, Raghu V. [Center for Emerging Technologies, Jain Global Campus, Jain University, Jakkasandra, Ramanagara 562-112 (India); Aminabhavi, Tejraj M. [Soniya College of Pharmacy, S. R. Nagar, Dharwad 580-002 (India)

    2015-03-01

    Graphene was oxidized with H{sub 2}O{sub 2} to introduce additional anchoring sites for effective alumina coating on graphene by the sol–gel method. The X-ray photoelectron spectroscopy studies showed that the oxygen-containing groups such as hydroxyl group useful for coating were introduced by the oxidation. The transmission electron microscopy images and thermogravimetric analysis data demonstrated that the additional anchoring sites enhanced the efficiency of the alumina coating. A small amount of alumina-coated graphene synergistically improved the thermal conductivity of the alumina sphere/thermoplastic polyurethane (TPU) composite without any increase in the electrical conductivity, because the electrical conductivity of graphene effectively decreased by the alumina coating. Moreover, the synergistic effect of a small amount of graphene was enhanced by the alumina coating, and the stiffening of the alumina sphere/TPU composite due to the added graphene was alleviated by the alumina coating. - Highlights: • Oxidation of graphene with H{sub 2}O{sub 2} introduced anchoring sites for alumina coating. • The anchoring sites improved the efficiency of alumina coating on graphene. • The alumina-coated graphene synergistically enhanced the thermal conductivity.

  8. Rheological Properties of Aqueous Nanometric Alumina Suspensions

    Energy Technology Data Exchange (ETDEWEB)

    Li, Chuanping [Iowa State Univ., Ames, IA (United States)

    2004-01-01

    Colloidal processing is an effective and reliable approach in the fabrication of the advanced ceramic products. Successful colloidal processing of fine ceramic powders requires accurate control of the rheological properties. The accurate control relies on the understanding the influences of various colloidal parameters on the rheological properties. Almost all research done on the rheology paid less attention to the interactions of particle and solvent. However, the interactions of the particles are usually built up through the media in which the particles are suspended. Therefore, interactions of the particle with the media, the adsorbed layers on the particle surface, and chemical and physical properties of media themselves must influence the rheology of the suspension, especially for the dense suspensions containing nanosized particles. Relatively little research work has been reported in this area. This thesis addresses the rheological properties of nanometric alumina aqueous suspensions, and paying more attention to the interactions between particle and solvent, which in turn influence the particle-particle interactions. Dense nanometric alumina aqueous suspensions with low viscosity were achieved by environmentally-benign fructose additives. The rheology of nanometric alumina aqueous suspensions and its variation with the particle volume fraction and concentration of fructose were explored by rheometry. The adsorptions of solute (fructose) and solvent (water) on the nanometric alumina particle surfaces were measured and analyzed by TG/DSC, TOC, and NMR techniques. The mobility of water molecules in the suspensions and its variation with particle volume fractions and fructose additive were determined by the 17O NMR relaxation method. The interactions between the nanometric alumina particles in water and fructose solutions were investigated by AFM. The results indicated that a large number of water layers were physically bound on the particles

  9. Rheological Properties of Aqueous Nanometric Alumina Suspensions

    Energy Technology Data Exchange (ETDEWEB)

    Chuanping Li

    2004-12-19

    Colloidal processing is an effective and reliable approach in the fabrication of the advanced ceramic products. Successful colloidal processing of fine ceramic powders requires accurate control of the rheological properties. The accurate control relies on the understanding the influences of various colloidal parameters on the rheological properties. Almost all research done on the rheology paid less attention to the interactions of particle and solvent. However, the interactions of the particles are usually built up through the media in which the particles are suspended. Therefore, interactions of the particle with the media, the adsorbed layers on the particle surface, and chemical and physical properties of media themselves must influence the rheology of the suspension, especially for the dense suspensions containing nanosized particles. Relatively little research work has been reported in this area. This thesis addresses the rheological properties of nanometric alumina aqueous suspensions, and paying more attention to the interactions between particle and solvent, which in turn influence the particle-particle interactions. Dense nanometric alumina aqueous suspensions with low viscosity were achieved by environmentally-benign fructose additives. The rheology of nanometric alumina aqueous suspensions and its variation with the particle volume fraction and concentration of fructose were explored by rheometry. The adsorptions of solute (fructose) and solvent (water) on the nanometric alumina particle surfaces were measured and analyzed by TG/DSC, TOC, and NMR techniques. The mobility of water molecules in the suspensions and its variation with particle volume fractions and fructose additive were determined by the {sup 17}O NMR relaxation method. The interactions between the nanometric alumina particles in water and fructose solutions were investigated by AFM. The results indicated that a large number of water layers were physically bound on the particles

  10. Control of the γ-alumina to α-alumina phase transformation for an optimized alumina densification

    Energy Technology Data Exchange (ETDEWEB)

    Lamouri, S.; Hamidouche, M.; Bouaouadja, N.; Belhouchet, H.; Garnier, V.; Fantozzi, G.; Trelkat, J.F.

    2017-07-01

    In this work, we studied the aptitude to sintering green bodies using γ-Al2O3 transition alumina as raw powder. We focused on the influence of the heating rate on densification and microstructural evolution. Phase transformations from transition alumina γ→δ→θ→α-Al2O3 were studied by in situ X-rays diffraction from the ambient to 1200°C. XRD patterns revealed coexistence of various phase transformations during the heating cycle. DTA and dilatometry results showed that low heating rate leads to a significant reduction of the temperature of the α-Al2O3 alumina formation. Around 1190, 1217 and 1240°C were found when using 5, 10 and 20°C/min of heating rate, respectively. The activation energy for θ-Al2O3→α-Al2O3 transformation calculated by Kissinger and JMA equations using dilatometry method were 464.29 and 488.79kJ/mol, respectively and by DTA method were 450.72 and 475.49kJ/mol, respectively. In addition, the sintering of the green bodies with low heating rate promotes the rearrangement of the grains during θ-Al2O3→α-Al2O3 transformation, enhancing the relative density to 95% and preventing the development of a vermicular structure. (Author)

  11. Control of the γ-alumina to α-alumina phase transformation for an optimized alumina densification

    Directory of Open Access Journals (Sweden)

    Samir Lamouri

    2017-03-01

    Full Text Available In this work, we studied the aptitude to sintering green bodies using γ-Al2O3 transition alumina as raw powder. We focused on the influence of the heating rate on densification and microstructural evolution. Phase transformations from transition alumina γ → δ → θ → α-Al2O3 were studied by in situ X-rays diffraction from the ambient to 1200 °C. XRD patterns revealed coexistence of various phase transformations during the heating cycle. DTA and dilatometry results showed that low heating rate leads to a significant reduction of the temperature of the α-Al2O3 alumina formation. Around 1190, 1217 and 1240 °C were found when using 5, 10 and 20 °C/min of heating rate, respectively. The activation energy for θ-Al2O3 → α-Al2O3 transformation calculated by Kissinger and JMA equations using dilatometry method were 464.29 and 488.79 kJ/mol, respectively and by DTA method were 450.72 and 475.49 kJ/mol, respectively. In addition, the sintering of the green bodies with low heating rate promotes the rearrangement of the grains during θ-Al2O3 → α-Al2O3 transformation, enhancing the relative density to 95% and preventing the development of a vermicular structure.

  12. Shadows alter facial expressions of Noh masks.

    Science.gov (United States)

    Kawai, Nobuyuki; Miyata, Hiromitsu; Nishimura, Ritsuko; Okanoya, Kazuo

    2013-01-01

    A Noh mask, worn by expert actors during performance on the Japanese traditional Noh drama, conveys various emotional expressions despite its fixed physical properties. How does the mask change its expressions? Shadows change subtly during the actual Noh drama, which plays a key role in creating elusive artistic enchantment. We here describe evidence from two experiments regarding how attached shadows of the Noh masks influence the observers' recognition of the emotional expressions. In Experiment 1, neutral-faced Noh masks having the attached shadows of the happy/sad masks were recognized as bearing happy/sad expressions, respectively. This was true for all four types of masks each of which represented a character differing in sex and age, even though the original characteristics of the masks also greatly influenced the evaluation of emotions. Experiment 2 further revealed that frontal Noh mask images having shadows of upward/downward tilted masks were evaluated as sad/happy, respectively. This was consistent with outcomes from preceding studies using actually tilted Noh mask images. Results from the two experiments concur that purely manipulating attached shadows of the different types of Noh masks significantly alters the emotion recognition. These findings go in line with the mysterious facial expressions observed in Western paintings, such as the elusive qualities of Mona Lisa's smile. They also agree with the aesthetic principle of Japanese traditional art "yugen (profound grace and subtlety)", which highly appreciates subtle emotional expressions in the darkness.

  13. Shadows alter facial expressions of Noh masks.

    Directory of Open Access Journals (Sweden)

    Nobuyuki Kawai

    Full Text Available BACKGROUND: A Noh mask, worn by expert actors during performance on the Japanese traditional Noh drama, conveys various emotional expressions despite its fixed physical properties. How does the mask change its expressions? Shadows change subtly during the actual Noh drama, which plays a key role in creating elusive artistic enchantment. We here describe evidence from two experiments regarding how attached shadows of the Noh masks influence the observers' recognition of the emotional expressions. METHODOLOGY/PRINCIPAL FINDINGS: In Experiment 1, neutral-faced Noh masks having the attached shadows of the happy/sad masks were recognized as bearing happy/sad expressions, respectively. This was true for all four types of masks each of which represented a character differing in sex and age, even though the original characteristics of the masks also greatly influenced the evaluation of emotions. Experiment 2 further revealed that frontal Noh mask images having shadows of upward/downward tilted masks were evaluated as sad/happy, respectively. This was consistent with outcomes from preceding studies using actually tilted Noh mask images. CONCLUSIONS/SIGNIFICANCE: Results from the two experiments concur that purely manipulating attached shadows of the different types of Noh masks significantly alters the emotion recognition. These findings go in line with the mysterious facial expressions observed in Western paintings, such as the elusive qualities of Mona Lisa's smile. They also agree with the aesthetic principle of Japanese traditional art "yugen (profound grace and subtlety", which highly appreciates subtle emotional expressions in the darkness.

  14. Spatial release from informational masking

    Science.gov (United States)

    Rakerd, Brad; Aaronson, Neil L.

    2001-05-01

    A new method for investigating spatial release from informational masking was developed and employed in two experiments. The new method is computer controlled and efficient. It employs the versatile coordinate response measure speech stimulus set [Bolia et al., J. Acoust. Soc. Am. 107, 1065 (2000)]. The experiments were conducted in an anechoic room, with a primary loudspeaker in front of the listener and a secondary loudspeaker at 60 deg to the right. Target messages were presented from the primary speaker only. For a standard, distractor messages, simultaneous with the target, were also presented from the primary speaker only. Spatial release was measured by presenting the distractors from both primary and secondary speakers with a temporal offset. Experiment 1 fixed the offset (secondary leading, +4 ms) and varied the number of distractors (1 to 3) and the target-to-distractor ratio (-12 to +4 dB). Masking release, sometimes as large as 10 dB, was found for all combinations of these variables. Experiment 2 varied the offset over a wide range of values. Substantial release from masking was found for both positive and negative offsets, but only in the range in which speech echoes are suppressed (<50 ms). [Work supported by NIDCD grant DC 00181.

  15. Magnetic properties and magnetization reversal of α-Fe nanowires deposited in alumina film

    Science.gov (United States)

    Peng, Yong; Zhang, Hao-Li; Pan, Shan-Lin; Li, Hu-Lin

    2000-05-01

    Uniform arrays of Fe nanowires were prepared by electrochemical deposition of iron into nanoporous anodic aluminum oxide films. The microstructure and crystal structures of the nanowires were studied by transmission electron microscopy and electron diffraction. It was found that each nanowire looked like a chain of dots and each dot in the chain was supposed to be a single crystal of α-Fe. Each dot was shown to be a single magnetic domain. The magnetic properties of a uniform array of Fe nanowires and the magnetization reversal in a Fe nanowire were investigated by Mössbauer spectroscopy and vibrating sample magnetometry, which demonstrated that the film of Fe nanowires in alumina had superior perpendicular magnetic characteristics. The magnetic studies also revealed that the moments of each single domain dot were oriented along the chain. Experimental results could be interpreted by the reversal model of "chains of spheres" with the symmetric fanning mechanism.

  16. Modulating molecular transport across peptide-modified nanoporous alumina membranes with light

    Science.gov (United States)

    Kumeria, Tushar; Yu, Jingxian; Alsawat, Mohammed; Kurkuri, Mahaveer D.; Santos, Abel; Abell, Andrew D.; Losic, Dusan

    2016-12-01

    We designed and fabricated a smart and stimuli responsive membrane to cater on demand molecular transporting applications. A novel photoswitchable peptide (PSP) was synthesized and attached inside nanoporous anodic alumina membranes (NAAMs) pores. The PSP specifically switched between its cis and trans photostationary states on exposure to 364 nm and 440 nm wavelength lights respectively, which not only provided the ability to control its pore diameter but also the surface chemistry. The switchable molecular transport properties of the PSP-NAAMs have been shown as a function of the light exposure. Most importantly, the molecular transport across PSP-NAAMs could be repeatedly switched between on and off state, which is highly significant for on-demand triggered drug release systems.

  17. Influence of alumina characteristics on glaze properties

    Directory of Open Access Journals (Sweden)

    Arrufat, S.

    2010-10-01

    Full Text Available Aluminium oxide is a synthetic raw material manufactured from bauxite by the Bayer process, whose Al2O3 content typically exceeds 99%. Four main types of alumina can be defined, depending on the processing used: hydrargillite Al(OH3, boehmite AlOOH, transition aluminas (calcined at low temperatures, 1000 °C, with an intermediary crystallographic structure between hydrates and alpha alumina, and α-Al2O3 (calcined at high temperatures, >1100 °C. In glaze manufacturing, α-Al2O3 is the main type of alumina used. This raw material acts as a matting agent: the matt effect depends on alumina particle size and content in the glaze. This study examines the effect of the degree of alumina calcination on glaze technical and aesthetic properties. For this purpose, aluminas with different degrees of calcination were added to a glaze formulated with a transparent frit and kaolin, in order to simplify the system to be studied. The results show that, depending on the degree of calcination, alumina particles can react with the glaze components (SiO2, CaO, and ZnO to form new crystalline phases (anorthite and gahnite. Both crystallisations extract CaO and ZnO from the glassy phase, increasing glassy phase viscosity. The variation in crystalline phases and glassy phase viscosity yields glazes with different technical and aesthetic properties.

    El óxido de aluminio es una materia prima sintética fabricada a partir de la bauxita por medio del proceso Bayer, cuyo contenido de Al2O3 supera, por regla general, el 99%. Se pueden definir cuatro tipos de alúmina, en función del tipo de proceso usado: hidrargilita Al(OH3, boehmita AlOOH, alúminas de transición (calcinadas a bajas temperaturas, 1000 °C, con una estructura cristalográfica intermedia entre los hidratos y la alfa alúmina, y la α-Al2O3 (calcinada a

  18. Impact of AD995 alumina rods

    Energy Technology Data Exchange (ETDEWEB)

    Chhabildas, L.C.; Furnish, M.D.; Reinhart, W.D. [Sandia National Labs., Albuquerque, NM (United States); Grady, D.E. [Applied Research Associates, Inc., Albuquerque, NM (United States)

    1997-10-01

    Gas guns and velocity interferometric techniques have been used to determine the loading behavior of an AD995 alumina rod 19 mm in diameter by 75 mm and 150 mm long, respectively. Graded-density materials were used to impact both bare and sleeved alumina rods while the velocity interferometer was used to monitor the axial-velocity of the free end of the rods. Results of these experiments demonstrate that (1) a time-dependent stress pulse generated during impact allows an efficient transition from the initial uniaxial strain loading to a uniaxial stress state as the stress pulse propagates through the rod, and (2) the intermediate loading rates obtained in this configuration lie between split Hopkinson bar and shock-loading techniques.

  19. Silica containing highly porous alumina ceramic

    Science.gov (United States)

    Svinka, R.; Svinka, V.; Zake, I.

    2011-04-01

    Porous alumina ceramic were produced by slip casting of aqueous alumina slurry with added small amount of metallic aluminium powder. Pores form in result of chemical reaction of aluminum with water by hydrogen gas evolution reaction and solidification of suspension. Porosity of such materials sintered at a temperature of 1600 - 1750°C varies from 60 to 90%. Pore size distribution and mechanical strength of these materials depend largely on the grain size of used raw materials. The major part of pores in the materials produced without additive of silica are larger than 10 ±m, but with 5 - 10 wt.% additive of silica in the raw mix pore size decreases considerably. The sintering shrinkage decreases to 2.5%. Coefficient of thermal expansion equally decreases from 8.9-10-6 K-1 to 7.1 10-6 K-1 and classification temperature increases to 1600°C, while deformation at high temperature decreases considerably.

  20. Improvement in nanoscale contact resistance of alumina

    Energy Technology Data Exchange (ETDEWEB)

    Bhattacharya, Manjima; Chakraborty, Riya; Mandal, Ashok Kumar [CSIR - Central Glass and Ceramic Research Institute, Kolkata (India); Dey, Arjun [CSIR - Central Glass and Ceramic Research Institute, Kolkata (India); ISRO Satellite Centre, Thermal Systems Group, Bangalore (India); Mukhopadhyay, Anoop Kumar [CSIR - Central Glass and Ceramic Research Institute, Kolkata (India); Central Glass and Ceramic Research Institute, Kolkata 32 (India)

    2012-06-15

    In all contact-related applications such as the wear-resistant inserts, biomedical implants, high strain rate impact-resistant plates, etc., nanohardness, i.e. the intrinsic contact resistance at the nano scale, plays a major role. In spite of the wealth of literature, the studies on nanohardness of dense, coarse-grain alumina ceramics which represent many commercial varieties; have reasonably good hardness at the macro scale and characteristically exhibit R-curve behaviour, are far from significant. Here, to the best of our knowledge, we report for the first time the experimental observations of the increase in intrinsic contact resistance at the nano scale with the loading rate applied to a high-density ({proportional_to}95 % of theoretical) coarse-grain ({proportional_to}20 {mu}m) alumina ceramics. These observations were explained in terms of the initiation of nanoscale plasticity and maximum shear stress generated just underneath the nanoindenter. (orig.)

  1. Multi-anode ionization chamber

    Energy Technology Data Exchange (ETDEWEB)

    Bolotnikov, Aleksey E. (South Setauket, NY); Smith, Graham (Port Jefferson, NY); Mahler, George J. (Rocky Point, NY); Vanier, Peter E. (Setauket, NY)

    2010-12-28

    The present invention includes a high-energy detector having a cathode chamber, a support member, and anode segments. The cathode chamber extends along a longitudinal axis. The support member is fixed within the cathode chamber and extends from the first end of the cathode chamber to the second end of the cathode chamber. The anode segments are supported by the support member and are spaced along the longitudinal surface of the support member. The anode segments are configured to generate at least a first electrical signal in response to electrons impinging thereon.

  2. Tribology of alumina-graphite composites

    Science.gov (United States)

    Yu, Chih-Yuan

    Alumina-graphite composites, which combine high wear resistance and self-lubricity, are a potential and promising candidate for advanced tribological applications. The processing, mechanical properties and tribology of alumina-graphite composites are discussed. Full density is difficult to achieve by a pressureless sintering route. Porosity of the composites increases with graphite content which causes the strength, modulus of elasticity, and hardness of the composites to decrease. The increased porosity does cause the fracture toughness to slightly increases. Tribology of alumina-graphite composites was studied with a pin-on-disk tribometer with emphasis on the following aspects: the graphite content in both pin and disk, the graphite flake size and the orientation of the graphite flakes. Scan electronic microscopy (SEM) and X-ray diffraction are utilized to examine and characterize the wear debris and the worn surface. Results confirmed that it is necessary to optimize the structure and the supply of lubricant to improve the tribological behavior and that the arrangements of sliding couples also affect the tribology of self-lubricated ceramic composites. Continuous measurements of the friction coefficients were collected at high frequency in an attempt to correlate the tribology of alumina-graphite composites to vibrations introduced by friction. While these measurements indicate that the time frequency behavior of tribology is an important area of study, conclusions regarding the frequency response of different sliding couples could not be definitively stated. Finally, a new concept connecting instantaneous wear coefficient and instantaneous contact stress is proposed for prediction of wear behavior of brittle materials.

  3. Boehmite nanostructures preparation by hydrothermal method from anodic aluminium oxide membrane.

    Science.gov (United States)

    Yang, X; Wang, J Y; Pan, H Y

    2009-02-01

    Boehmite nanostructures were successfully synthesized from porous anodic aluminium oxide (AAO) membrane by a simple and efficient hydro-thermal method. The experiment used high purity alumina as raw material, and the whole reaction process avoided superfluous impurities to be introduced. Thus, the purity of Boehmite products was ensured. The examinations of the morphology and structure were carried out by atomic force microscope (AFM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). Composition of the specimens was analyzed using energy dispersive X-ray spectroscope (EDX) and X-ray diffraction (XRD). Based on these observations the growth process was analyzed.

  4. Application of Boron Oxide as a Protective Surface Treatment to Decrease the Air Reactivity of Carbon Anodes

    Directory of Open Access Journals (Sweden)

    Ramzi Ishak

    2017-03-01

    Full Text Available The oxidation of a carbon anode with air and CO2 occurs during the electrolysis of alumina in Hall-Héroult cells, resulting in a significant overconsumption of carbon and dusting. Boron is well known to decrease the rate of this reaction for graphite. In this work, the application of boron oxide has been investigated to evaluate its inhibition effect on the air oxidation reaction, and to provide an effective protection for anodes. Different methods of impregnation coating have been explored. Impregnated anode samples were gasified under air at 525 °C according to the standard measurement methods. X-ray tomography was used to obtain the microstructural information of the samples before and after air-burning tests. The impregnated samples showed a very low oxidation reaction rate and dust generation.

  5. Fabrication of ZnO Nanowires Arrays by Anodization and High-Vacuum Die Casting Technique, and Their Piezoelectric Properties.

    Science.gov (United States)

    Kuo, Chin-Guo; Chang, Ho; Wang, Jian-Hao

    2016-03-24

    In this investigation, anodic aluminum oxide (AAO) with arrayed and regularly arranged nanopores is used as a template in the high-vacuum die casting of molten zinc metal (Zn) into the nanopores. The proposed technique yields arrayed Zn nanowires with an aspect ratio of over 600. After annealing, arrayed zinc oxide (ZnO) nanowires are obtained. Varying the anodizing time yields AAO templates with thicknesses of approximately 50 μm, 60 μm, and 70 μm that can be used in the fabrication of nanowires of three lengths with high aspect ratios. Experimental results reveal that a longer nanowire generates a greater measured piezoelectric current. The ZnO nanowires that are fabricated using an alumina template are anodized for 7 h and produce higher piezoelectric current of up to 69 pA.

  6. Fabrication of ZnO Nanowires Arrays by Anodization and High-Vacuum Die Casting Technique, and Their Piezoelectric Properties

    Directory of Open Access Journals (Sweden)

    Chin-Guo Kuo

    2016-03-01

    Full Text Available In this investigation, anodic aluminum oxide (AAO with arrayed and regularly arranged nanopores is used as a template in the high-vacuum die casting of molten zinc metal (Zn into the nanopores. The proposed technique yields arrayed Zn nanowires with an aspect ratio of over 600. After annealing, arrayed zinc oxide (ZnO nanowires are obtained. Varying the anodizing time yields AAO templates with thicknesses of approximately 50 μm, 60 μm, and 70 μm that can be used in the fabrication of nanowires of three lengths with high aspect ratios. Experimental results reveal that a longer nanowire generates a greater measured piezoelectric current. The ZnO nanowires that are fabricated using an alumina template are anodized for 7 h and produce higher piezoelectric current of up to 69 pA.

  7. Degradation behavior of anode-supported solid oxide fuel cell using LNF cathode as function of current load

    Energy Technology Data Exchange (ETDEWEB)

    Komatsu, Takeshi; Yoshida, Yoshiteru; Watanabe, Kimitaka; Chiba, Reiichi; Taguchi, Hiroaki; Orui, Himeko; Arai, Hajime [NTT Energy and Environment Systems Laboratories, Atsugi-shi, Kanagawa 243-0198 (Japan)

    2010-09-01

    We investigated the effect of current loading on the degradation behavior of an anode-supported solid oxide fuel cell (SOFC). The cell consisted of LaNi{sub 0.6}Fe{sub 0.4}O{sub 3} (LNF), alumina-doped scandia stabilized zirconia (SASZ), and a Ni-SASZ cermet as the cathode, electrolyte, and anode, respectively. The test was carried out at 1073 K with constant loads of 0.3, 1.0, 1.5, and 2.3 A cm{sup -2}. The degradation rate, defined by the voltage loss during a fixed period (about 1000 h), was faster at higher current densities. From an impedance analysis, the degradation depended mainly on increases in the cathodic resistance, while the anodic and ohmic resistances contributed very little. The cathode microstructures were observed using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). (author)

  8. Synthesis and characterization of single-crystalline alumina nanowires

    Institute of Scientific and Technical Information of China (English)

    ZHAO Qing; XU Xiang-yu; ZHANG Hong-zhou; CHEN Yao-feng; XU Jun; YU Da-peng

    2005-01-01

    Alumina nanowires were synthesized on large-area silicon substrate via simple thermal evaporation method of heating a mixture of aluminum and alumina powders without using any catalyst or template. The phase structure and the surface morphology of the as-grown sample were analyzed by X-ray diffractometry(XRD) and scanning electron microscopy (SEM), respectively. The chemical composition and the microstructure of the as-grown alumina nanowires were characterized using transmission electron microscope(TEM). The nanowires are usually straight and the single crystalline has average diameter of 40 nm and length of 3 - 5 μm. The growth direction is along the [002] direction. Well aligned alumina nanowire arrays were observed on the surface of many large particles. The catalyst-free growth of the alumina nanowires was explained under the framework of a vapor-solid(VS)growth mechanism. This as-synthesized alumina nanowires could find potential applications in the fabrication of nanodevices.

  9. Porous Aluminas: The bio template method for the synthesis of stable high surface area aluminas; Aluminas porosas: El metodo de bio-replica para la sintesis de aluminas estables de alta superficie especifica

    Energy Technology Data Exchange (ETDEWEB)

    Benitez Guerrero, M.; Perez Maqueda, L.; Pena Castro, P.; Pascual Cosp, J.

    2013-07-01

    Development of porous alumina has been the objective of numerous studies in recent decades, due to the intrinsic properties of aluminium oxide, such as high melting point, low thermal conductivity, chemical inertness and corrosion resistance which, in addition to a high surface area and permeability, make aluminas being used for many different industrial and technical applications. The crystallographic and textural stability of alumina acquires significant importance in those processes involving high temperatures; however, most of the synthesis methods yield metastable oxides of little interest in high-temperature processes due to the transformation to alpha phase, with the consequent reduction in surface area. The present article reviews diverse procedures for obtaining porous alumina with high specific surface area, including methods and strategies for preparing high surface alpha-alumina. Within this framework, the paper analyzes the results obtained through bio replica of lignocellulose materials. This technology allows preparing aluminas with the complex structural hierarchy of the lignocellulose templates. (Author)

  10. High performance mask fabrication process for the next-generation mask production

    Science.gov (United States)

    Yagawa, Keisuke; Ugajin, Kunihiro; Suenaga, Machiko; Kobayashi, Yoshihito; Motokawa, Takeharu; Hagihara, Kazuki; Saito, Masato; Itoh, Masamitsu

    2014-07-01

    ArF immersion lithography combined with double patterning has been used for fabricating below half pitch 40nm devices. However, when pattern size shrinks below 20nm, we must use new technology like quadruple patterning process or next generation lithography (NGL) solutions. Moreover, with change in lithography tool, next generation mask production will be needed. According to ITRS 2013, fabrication of finer patterns less than 15nm will be required on mask plate in NGL mask production 5 years later [1]. In order to fabricate finer patterns on mask, higher resolution EB mask writer and high performance fabrication process will be required. In a previous study, we investigated a potential of mask fabrication process for finer patterning and achieved 17nm dense line pattern on mask plate by using VSB (Variable Shaped Beam) type EB mask writer and chemically amplified resist [2][3]. After a further investigation, we constructed higher performance mask process by using new EB mask writer EBM9000. EBM9000 is the equipment supporting hp16nm generation's photomask production and has high accuracy and high throughput. As a result, we achieved 15.5nm pattern on mask with high productivity. Moreover, from evaluation of isolated pattern, we proved that current mask process has the capability for sub-10nm pattern. These results show that the performance of current mask fabrication process have the potential to fabricate the next-generation mask.

  11. Fabrication of TiO2 Nanotanks Embedded in a Nanoporous Alumina Template

    Directory of Open Access Journals (Sweden)

    C. Massard

    2015-01-01

    Full Text Available The feasibility of surface nanopatterning with TiO2 nanotanks embedded in a nanoporous alumina template was investigated. Self-assembled anodized aluminium oxide (AAO template, in conjunction with sol gel process, was used to fabricate this nanocomposite object. Through hydrolysis and condensation of the titanium alkoxide, an inorganic TiO2 gel was moulded within the nanopore cavities of the alumina template. The nanocomposite object underwent two thermal treatments to stabilize and crystallize the TiO2. The morphology of the nanocomposite object was characterized by Field Emission Scanning Electron Microscopy (FESEM. The TiO2 nanotanks obtained have cylindrical shapes and are approximately 69 nm in diameter with a tank-to-tank distance of 26 nm. X-ray diffraction analyses performed by Transmission Electron Microscopy (TEM with selected area electron diffraction (SAED were used to investigate the TiO2 structure. The optical properties were studied using UV-Vis spectroscopy.

  12. Commercial alumina templates as base to fabricate 123-type high-T{sub c} superconductor nanowires

    Energy Technology Data Exchange (ETDEWEB)

    Koblischka, M.R.; Zeng, X.L.; Hartmann, U. [Institute of Experimental Physics, Saarland University, P. O. Box 151150, 66041 Saarbruecken (Germany)

    2016-04-15

    Nanowires of high-T{sub c} superconductors of the RE-123 type (RE = rare earths) were grown by the anodized alumina template method, employing commercially available alumina templates with nominal pore diameters of 20 and 100 nm. Pre-reacted YBa{sub 2}Cu{sub 3}O{sub x} (YBCO) and NdBa{sub 2}Cu{sub 3}O{sub x} (NdBCO) powder was molten on top of the templates in order to fill the pores with the 123-type material. The resulting samples were oxygen-annealed at 450 C. Superconductivity with a transition temperature of 88 K (YBCO) and 96 K (NdBCO) was confirmed by means of magnetic susceptibility measurements (SQUID) using pieces of the filled template. The electric (resistance) and magnetic measurements revealed further relatively sharp superconducting transitions. To understand the dimensions of the resulting nanowires (length up to 10 μm, diameter between 100 and 250 nm), which do not correspond to the nominal pore diameters, the empty and filled commercial templates were analyzed in detail by scanning electron microscopy. We discuss the feasibility of this approach to produce larger amounts of nanowires. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  13. Influence of TAC on Dispersion of Aqueous Nano Alumina Suspension

    Institute of Scientific and Technical Information of China (English)

    ZHAO Wei; YANG De-an; SONG Jian-jing; YANG Zi; LIANG Chong; XU Ming-xia; XU Ting-xian

    2004-01-01

    The stability of aqueous nano alumina powder suspensions with and without dispersant tri-ammonium citrate (TAC) was investigated by measuring zeta potential at different pH values. The isoelectric point (IEP) of alumina powder shifts towards more acidic pH range by adding TAC dispersant. The results illustrate that adsorption of TAC on alumina powder surface existed in the aqueous suspension, which leads to a high stability of the suspension.

  14. Novel self assembly behavior for γ-alumina nanoparticles

    Institute of Scientific and Technical Information of China (English)

    Osama Saber

    2012-01-01

    In this study,self assembly behavior was induced for γ-alumina nanoparticles by adsorption of dimethyl disulfide.Following this trend,we have developed a chemical process to obtain γ-alumina in the nano scale.Scanning electron microscopy images of the prepared γ-alumina showed big and strong agglomeration of the nanoparticles indicating that these nanoparticles have strong surface forces.Transmission electron microscopy images confirmed that the γ-alumina nanoparticles 3-7 nm in size were converted to uniform spherical shape in the size range of 1-2 mm after shaking with dimethyl disulfide in the presence of n-hexane at room temperature.This phenomenon did not appear in the case of alumina in the micro scale.The surface properties of the prepared γ-alumina in the nano scale were characterized and compared with the γ-alumina in the micro scale by using low temperature nitrogen adsorption-desorption system,indicating that the specific surface area of the prepared γ-alumina nanoparticles is larger than that of the γ-alumina in the micro scale.Furthermore,micro-and meso-pores were observed for the γ-alumina nanoparticles while only mesoporous structure was detected for the γ-alumina in the micro scale.These experimental results suggested that the self assembly behavior of the γ-alumina nanoparticles may be due to the selective adsorption of dimethyl disulfide in the micropores of these nanoparticles to act as bridge linking the nanoparticles.

  15. Liquid-metal electrode to enable ultra-low temperature sodium-beta alumina batteries for renewable energy storage.

    Science.gov (United States)

    Lu, Xiaochuan; Li, Guosheng; Kim, Jin Y; Mei, Donghai; Lemmon, John P; Sprenkle, Vincent L; Liu, Jun

    2014-01-01

    Commercial sodium-sulphur or sodium-metal halide batteries typically need an operating temperature of 300-350 °C, and one of the reasons is poor wettability of liquid sodium on the surface of beta alumina. Here we report an alloying strategy that can markedly improve the wetting, which allows the batteries to be operated at much lower temperatures. Our combined experimental and computational studies suggest that addition of caesium to sodium can markedly enhance the wettability. Single cells with Na-Cs alloy anodes exhibit great improvement in cycling life over those with pure sodium anodes at 175 and 150 °C. The cells show good performance even at as low as 95 °C. These results demonstrate that sodium-beta alumina batteries can be operated at much lower temperatures with successfully solving the wetting issue. This work also suggests a strategy to use liquid metals in advanced batteries that can avoid the intrinsic safety issues associated with dendrite formation.

  16. Mask data volume: explosion or damp squib?

    Science.gov (United States)

    Spence, Chris; Goad, Scott; Buck, Peter; Gladhill, Richard; Cinque, Russell

    2005-11-01

    Mask data file sizes are increasing as we move from technology generation to generation. The historical 30% linear shrink every 2-3 years that has been called Moore's Law, has driven a doubling of the transistor budget and hence feature count. The transition from steppers to step-and-scan tools has increased the area of the mask that needs to be patterned. At the 130nm node and below, Optical Proximity Correction (OPC) has become prevalent, and the edge fragmentation required to implement OPC leads to an increase in the number of polygons required to define the layout. Furthermore, Resolution Enhancement Techniques (RETs) such as Sub-Resolution Assist Features (SRAFs) or tri-tone Phase Shift Masks (PSM) require additional features to be defined on the mask which do not resolve on the wafer, further increasing masks volumes. In this paper we review historical data on mask file sizes for microprocessor designs. We consider the consequences of this increase in file size on Mask Data Prep (MDP) activities, both within the Integrated Device Manufacturer (IDM) and Mask Shop, namely: computer resources, storage and networks (for file transfer). The impact of larger file sizes on mask writing times is also reviewed. Finally we consider, based on the trends that have been observed over the last 5 technology nodes, what will be required to maintain reasonable MDP and mask manufacturing cycle times.

  17. Corrosion of Refractory Alumina-Graphite and Alumina-Graphite-Zirconia in Slag Containing Titania

    Institute of Scientific and Technical Information of China (English)

    XU Yuan; LIU Qing-cai; BAI Chen-guang; CHEN Deng-fu; Joseph W Newkirk

    2004-01-01

    The corrosion of refractory alumina-graphite and alumina-graphite-zirconia in the slag containing titania was studied by immersion tests (quasi-static and dynamic tests). Combining direct observation with microscopic investigations, a mechanism for corrosion was proposed based on the oxidation of graphite and the dissolution of refractory components. During the corrosion process, there are some special phenomena and laws that can be explained by the relation between the corrosion rate and the TiO2 mass percent, the rotational refractory velocity and the morphology of the deteriorated layer.

  18. Aqueous combustion synthesis and characterization of zirconia-alumina nanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Kishan, J.; Mangam, Venu; Reddy, B.S.B.; Das, Siddhartha [Department of Metallurgical and Materials Engineering, Indian Institute of Technology, Kharagpur, West Bengal 721302 (India); Das, Karabi, E-mail: karabi@metal.iitkgp.ernet.i [Department of Metallurgical and Materials Engineering, Indian Institute of Technology, Kharagpur, West Bengal 721302 (India)

    2010-02-04

    The zirconia-alumina nanocomposite powders with 3-48 mol% of alumina are prepared by aqueous combustion synthesis technique using stoichiometric amounts of aluminium nitrate, zirconyl nitrate and glycine. The nanopowders are compacted uniaxially and sintered at 1000 {sup o}C temperature in a muffle furnace. Thermodynamic modeling of the combustion reaction shows that, as the alumina content increases, the amount of gases produced increases with a decrease in the adiabatic flame temperature. The green and sintered densities of cold press composite powders decrease with an increase in the mol% of alumina.

  19. Rheology of Alumina-Based Graphite-Containing Castables

    Institute of Scientific and Technical Information of China (English)

    YE Fangbao; M. Rigaud; LIU Xinhong; ZHONG Xiangchong

    2005-01-01

    In this work, the rheological behavior of ultra-low cement alumina-based castables with addition of flake graphite and extruded graphite pellets has been investigated by using IBB rheometer. Emphasis has been laid on the influence of the type and amount of carbon addition on rheological properties of the alumina-based castables and the results are compared with corresponding alumina castable samples without any carbon addition. It is found that alumina-based castables with extruded graphite pellets have good rheological behavior and flowability with lower water demand ( < 6. 3% )and no segregation during the shearing of castable.

  20. Electrically Conductive Anodized Aluminum Surfaces

    Science.gov (United States)

    Nguyen, Trung Hung

    2006-01-01

    Anodized aluminum components can be treated to make them sufficiently electrically conductive to suppress discharges of static electricity. The treatment was conceived as a means of preventing static electric discharges on exterior satin-anodized aluminum (SAA) surfaces of spacecraft without adversely affecting the thermal-control/optical properties of the SAA and without need to apply electrically conductive paints, which eventually peel off in the harsh environment of outer space. The treatment can also be used to impart electrical conductivity to anodized housings of computers, medical electronic instruments, telephoneexchange equipment, and other terrestrial electronic equipment vulnerable to electrostatic discharge. The electrical resistivity of a typical anodized aluminum surface layer lies between 10(exp 11) and 10(exp 13) Omega-cm. To suppress electrostatic discharge, it is necessary to reduce the electrical resistivity significantly - preferably to anodized surface becomes covered and the pores in the surface filled with a transparent, electrically conductive metal oxide nanocomposite. Filling the pores with the nanocomposite reduces the transverse electrical resistivity and, in the original intended outer-space application, the exterior covering portion of the nanocomposite would afford the requisite electrical contact with the outer-space plasma. The electrical resistivity of the nanocomposite can be tailored to a value between 10(exp 7) and 10(exp 12) Omega-cm. Unlike electrically conductive paint, the nanocomposite becomes an integral part of the anodized aluminum substrate, without need for adhesive bonding material and without risk of subsequent peeling. The electrodeposition process is compatible with commercial anodizing production lines. At present, the electronics industry uses expensive, exotic, electrostaticdischarge- suppressing finishes: examples include silver impregnated anodized, black electroless nickel, black chrome, and black copper. In

  1. Synthesis and properties of iridescent Zn-containing anodic aluminum oxide films

    Energy Technology Data Exchange (ETDEWEB)

    Jia, Xiaoxuan; Sun, Huiyuan, E-mail: huiyuansun@126.com; Liu, Lihu; Hou, Xue; Liu, Huiyuan

    2015-07-01

    A simple method of fabricating Zn-containing anodic aluminum oxide films for multifunctional anticounterfeit technology is reported. The resulting membranes were characterized with UV–vis illumination studies, natural light illumination color experiments, and electron microscopy analysis. Deposition of Zn in the nanopore region can enhance the color saturation of the thin alumina film with different colors dramatically. Both the anodization time and etching time have great influence on the structural color. The mechanisms for the emergence of this phenomenon are discussed and theoretical analysis further demonstrates the experimental results. - Highlights: • Iridescent PAA@Zn nanocomposite films were successfully fabricated. • A simple organics-assisted method is applied to making a series of fancy and multicolor patterns. • The color varies with the angle of incidence of the light used to view the film as is expected with Bragg–Snell formula. • Such colored films could be used in multifunctional anti-counterfeiting applications.

  2. Surface morphology, composition and thermal behavior of tungsten-containing anodic spark coatings on aluminium alloy

    Energy Technology Data Exchange (ETDEWEB)

    Lukiyanchuk, I.V.; Rudnev, V.S.; Kuryavyi, V.G.; Boguta, D.L.; Bulanova, S.B.; Gordienko, P.S

    2004-01-01

    Anodic spark coatings on aluminium alloy were prepared in aqueous electrolytes with sodium tungstate. The influence of boric acid addition in the electrolyte on the surface morphology, elemental and phase composition of the coatings was investigated. In both cases the coatings contained O, Al and W. The coatings obtained in electrolyte with boric acid and sodium tungstate contain also B at approximately 1 at.%. Scanning electron microscopy indicated that the coatings had three layers: the grey underlayer of anodic alumina, the second black layer of crystalline or amorphous aluminium tungstate agglomerated into fibers and the outer green layer of WO{sub 3}. It was proposed that isopoly- and heteropolyanions in the electrolyte used take part in the coating growth.

  3. Development of 3d micro-nano hybrid patterns using anodized aluminum and micro-indentation

    Energy Technology Data Exchange (ETDEWEB)

    Shin, Hong Gue; Kwon, Jong Tae [Division of Mechanical Engineering and Mechatronics, Kangwon National University, 1 Kangwondaehakgil, Chunchon, Gangwon-do, 200-701 (Korea, Republic of); Seo, Young Ho [Division of Mechanical Engineering and Mechatronics, Kangwon National University, 1 Kangwondaehakgil, Chunchon, Gangwon-do, 200-701 (Korea, Republic of)], E-mail: mems@kangwon.ac.kr; Kim, Byeong Hee [Division of Mechanical Engineering and Mechatronics, Kangwon National University, 1 Kangwondaehakgil, Chunchon, Gangwon-do, 200-701 (Korea, Republic of)

    2008-07-31

    We developed a simple and cost-effective method of fabricating 3D micro-nano hybrid patterns in which micro-indentation is applied on the anodized aluminum substrate. Nano-patterns were formed first on the aluminum substrate, and then micro-patterns were fabricated by deforming the nano-patterned aluminum substrate. Hemispherical nano-patterns with a 150 nm-diameter on an aluminum substrate were fabricated by anodizing and alumina removing process. Then, micro-pyramid patterns with a side-length of 50 {mu}m were formed on the nano-patterns using micro-indentation. To verify 3D micro-nano hybrid patterns, we replicated 3D micro-nano hybrid patterns by a hot-embossing process. 3D micro-nano hybrid patterns may be used in nano-photonic devices and nano-biochips applications.

  4. Helical apodizers for tunable hyper Gaussian masks

    Science.gov (United States)

    Ojeda-Castañeda, J.; Ledesma, Sergio; Gómez-Sarabia, Cristina M.

    2013-09-01

    We discuss an optical method for controlling the half-width of Gaussian like transmittance windows, by using a pair of absorption masks that have both radial and helical amplitude variations. For describing the radial part of the proposed masks, we employ amplitude transmittance profiles of the form T(ρ) = exp(- ρ s ). For s = 2, one has an amplitude transmittance that is proportional to a Gaussian function. A sub Gaussian mask is defined by a value of s 2, one has super Gaussian masks. Our discussion considers that any of these radially varying masks has also helical modulations. We show that by using a suitable pair of this type of masks, one can control the halfwidth of Gaussian like windows.

  5. Computational defect review for actinic mask inspections

    Science.gov (United States)

    Morgan, Paul; Rost, Daniel; Price, Daniel; Corcoran, Noel; Satake, Masaki; Hu, Peter; Peng, Danping; Yonenaga, Dean; Tolani, Vikram

    2013-04-01

    As optical lithography continues to extend into low-k1 regime, resolution of mask patterns continues to diminish. The limitation of 1.35 NA posed by water-based lithography has led to the application of various resolution enhancement techniques (RET), for example, use of strong phase-shifting masks, aggressive OPC and sub-resolution assist features, customized illuminators, etc. The adoption of these RET techniques combined with the requirements to detect even smaller defects on masks due to increasing MEEF, poses considerable challenges for a mask inspection engineer. Inspecting masks under their actinic-aerial image conditions would detect defects that are more likely to print under those exposure conditions. However, this also makes reviewing such defects in their low-contrast aerial images very challenging. On the other hand, inspecting masks under higher resolution inspection optics would allow for better viewing of defects post-inspection. However, such inspections generally would also detect many more defects, including printable and nuisance, thereby making it difficult to judge which are of real concern for printability on wafer. Often, an inspection engineer may choose to use Aerial and/or high resolution inspection modes depending on where in the process flow the mask is and the specific device-layer characteristics of the mask. Hence, a comprehensive approach is needed in handling defects both post-aerial and post-high resolution inspections. This analysis system is designed for the Applied Materials Aera™ mask inspection platform, all data reported was collected using the Aera.

  6. X-ray lithography masking

    Science.gov (United States)

    Smith, Henry I. (Inventor); Lim, Michael (Inventor); Carter, James (Inventor); Schattenburg, Mark (Inventor)

    1998-01-01

    X-ray masking apparatus includes a frame having a supporting rim surrounding an x-ray transparent region, a thin membrane of hard inorganic x-ray transparent material attached at its periphery to the supporting rim covering the x-ray transparent region and a layer of x-ray opaque material on the thin membrane inside the x-ray transparent region arranged in a pattern to selectively transmit x-ray energy entering the x-ray transparent region through the membrane to a predetermined image plane separated from the layer by the thin membrane. A method of making the masking apparatus includes depositing back and front layers of hard inorganic x-ray transparent material on front and back surfaces of a substrate, depositing back and front layers of reinforcing material on the back and front layers, respectively, of the hard inorganic x-ray transparent material, removing the material including at least a portion of the substrate and the back layers of an inside region adjacent to the front layer of hard inorganic x-ray transparent material, removing a portion of the front layer of reinforcing material opposite the inside region to expose the surface of the front layer of hard inorganic x-ray transparent material separated from the inside region by the latter front layer, and depositing a layer of x-ray opaque material on the surface of the latter front layer adjacent to the inside region.

  7. The Influence Of The Way Of Alumina Addition On Properties Improvement Of 3YSZ Material

    Directory of Open Access Journals (Sweden)

    Drożdż E.

    2015-06-01

    Full Text Available Yttria-stabilized zirconia (YSZ is the best known ceramic-oxide material employed as a component of either solid electrolyte or anode cermet material for intermediate solid oxide fuel cell (IT - SOFC. The properties of traditionally produced (by mechanical mixing of oxides Al2O3/3YSZ composite with the same composition materials obtained by citrate and impregnation methods and with properties of pure tetragonal zirconia (3YSZ were compared. The materials were characterised by X-ray diffraction, SEM observations with EDX analysis, density and impedance spectroscopy measurements. The results shown that Al2O3/3YSZ composites reveals higher conductivity than pure 3YSZ and that addition of alumina (regardless of methods improve electric properties of resulting materials. Taking into account application of this materials as anode in IT-SOFC the determined values of energy activation of conductivity and microstructural properties of composites show that materials obtained by citric method are the most promising.

  8. Damage of alumina films by medium energy hydrogen and helium ions

    CERN Document Server

    Bailey, P; Liu, Y; Alexander, M R; Koroleva, E V; Skeldon, P; Thompson, G E; Habazaki, H; Shimizu, K

    2002-01-01

    Following previous observations of detachment of amorphous, anodic alumina films from aluminium by 100 keV H sup + ions, further experiments have been carried out using H sup + , D sup + , sup 3 He sup + and sup 4 He sup + ions, at energies in the range of 0.5-270 keV, to irradiate anodized aluminium with oxides of thickness from 30 to 500 nm. Surface damage was investigated by field-emission-gun scanning electron microscopy and transmission electron microscopy. Detachment of the oxide, which takes place close to, or at, the metal/oxide interface, occurred only following irradiation by H sup + and D sup + ions, with the ions being stopped in the metal rather than the oxide. The threshold fluence for initiation of detachment is approximately 3x10 sup 1 sup 5 ions cm sup - sup 2. No detachment was detected following irradiations by sup 3 He sup + and sup 4 He sup + ions with fluences up to 5x10 sup 1 sup 6 ions cm sup - sup 2 and ranges similar to those of H sup + and D sup + ions, although vacancy production i...

  9. Quantification and morphology studies of nanoporous alumina membranes: a new algorithm for digital image processing.

    Science.gov (United States)

    Choudhari, Khoobaram S; Jidesh, Pacheeripadikkal; Sudheendra, Parampalli; Kulkarni, Suresh D

    2013-08-01

    A new mathematical algorithm is reported for the accurate and efficient analysis of pore properties of nanoporous anodic alumina (NAA) membranes using scanning electron microscope (SEM) images. NAA membranes of the desired pore size were fabricated using a two-step anodic oxidation process. Surface morphology of the NAA membranes with different pore properties was studied using SEM images along with computerized image processing and analysis. The main objective was to analyze the SEM images of NAA membranes quantitatively, systematically, and quickly. The method uses a regularized shock filter for contrast enhancement, mathematical morphological operators, and a segmentation process for efficient determination of pore properties. The algorithm is executed using MATLAB, which generates a statistical report on the morphology of NAA membrane surfaces and performs accurate quantification of the parameters such as average pore-size distribution, porous area fraction, and average interpore distances. A good comparison between the pore property measurements was obtained using our algorithm and ImageJ software. This algorithm, with little manual intervention, is useful for optimizing the experimental process parameters during the fabrication of such nanostructures. Further, the algorithm is capable of analyzing SEM images of similar or asymmetrically porous nanostructures where sample and background have distinguishable contrast.

  10. Anodic Bubble Behavior and Voltage Drop in a Laboratory Transparent Aluminum Electrolytic Cell

    Science.gov (United States)

    Zhao, Zhibin; Wang, Zhaowen; Gao, Bingliang; Feng, Yuqing; Shi, Zhongning; Hu, Xianwei

    2016-06-01

    The anodic bubbles generated in aluminum electrolytic cells play a complex role to bath flow, alumina mixing, cell voltage, heat transfer, etc., and eventually affect cell performance. In this paper, the bubble dynamics beneath the anode were observed for the first time from bottom view directly in a similar industrial electrolytic environment, using a laboratory-scale transparent aluminum electrolytic cell. The corresponding cell voltage was measured simultaneously for quantitatively investigating its relevance to bubble dynamics. It was found that the bubbles generated in many spots that increased in number with the increase of current density; the bubbles grew through gas diffusion and various types of coalescences; when bubbles grew to a certain size with their surface reaching to the anode edge, they escaped from the anode bottom suddenly; with the increase of current density, the release frequency increases, and the size of these bubbles decreases. The cell voltage was very consistent with bubble coverage, with a high bubble coverage corresponding to a higher cell voltage. At low current density, the curves of voltage and coverage fluctuated in a regularly periodical pattern, while the curves became more irregular at high current density. The magnitude of voltage fluctuation increased with current density first and reached a maximum value at current density of 0.9 A/cm2, and decreased when the current density was further increased. The extra resistance induced by bubbles was found to increase with the bubble coverage, showing a similar trend with published equations.

  11. NMR Revealed Activated Alumina-Water Interaction

    Institute of Scientific and Technical Information of China (English)

    ZHOU Rui; ZHOU Yan; HU Kai; JI Zhen-ping; CHENG Gong-zhen

    2005-01-01

    Three different spin-lattice relaxation times (T1) of water were obtained in activated alumina-water slurry system, which indicate that there exist three states of water: bound water, pore water and bulk water. The chemical shift (δH) decreases as the amount of water added to the system increases due to the differences in contribution of these three states of water in the samples. The δH value for adsorbed water decreases nearly linearly and T1 increases with elevating temperature, which result from the decrease in the content of bound water by the increase in thermal motion.

  12. Anisotropic shrinkage characteristics of tape cast alumina

    Science.gov (United States)

    Patwardhan, Jaideep Suresh

    Dimensional control during sintering is a major issue in ceramics processing to avoid high post-sintering costs associated with machining of the fired ceramic part to desired tolerances and dimensions. Ceramic forming processes such as tape casting, injection molding, and extrusion involve shear of anisotropic particles resulting in preferential alignment of the particles in the green body. This preferential alignment causes directionality in mechanical, electrical, optical, and magnetic properties and most importantly warpage or distortion during sintering. A large effort has been devoted to synthesizing ceramic green bodies with minimal density gradients and uniform packing and modeling the sintering behavior evolution but little effort has been devoted to characterizing orientation of particles and the effect of preferential alignment on sintering shrinkage anisotropy. A systematic study was initiated to study the effect of processing variables such as shear rate, solids loading, temperature, and binder content on aqueous tape cast alumina. Three different alumina systems: A16-SG, Baikowski RC-UFX DBM and RC-LS DBM were investigated. Aqueous tapes of high solids loading alumina (56 vol. %) were tape cast at various speeds and thicknesses and assuming plane Couette flow a shear rate regime of 21--270 s-1 was investigated. Higher shear rates and high solids loading resulted in higher in-plane anisotropy whereas the anisotropy in the thickness direction was higher for low solids loading systems. The anisotropy was found to be fairly constant above a certain critical shear rate (˜100 s-1) irrespective of the temperature and the solids loading and this correlated with the viscosity-shear rate relationship of the cast slips. The higher shrinkage anisotropy in the thickness direction for the low solids loading systems (35 and 45 vol. %) was attributed to the higher amount of organics in the slip required to sustain the suitable viscosity for tape casting and

  13. Intercalation of water into lithium. beta. -alumina

    Energy Technology Data Exchange (ETDEWEB)

    Dudney, N J; Bates, J B; Wang, J C; Brown, G M; Larson, B C; Engstrom, H

    1981-01-01

    Infrared absorption, neutron diffraction and weight loss techniques have been used to investigate the hydration of single crystals of Li ..beta..-alumina. The hydration is a reversible intercalation reaction. Up to approximately two water molecules per formula unit can penetrate the conduction plane. Other protonated species are formed from the dissociation of the molecular water. The rate of hydration is controlled by the diffusion of water in the conduction plane. A likely diffusion mechanism requires dissociation of the water and an interstitialcy motion of the oxygen.

  14. Alternating phase-shifted mask for logic gate levels, design, and mask manufacturing

    Science.gov (United States)

    Liebmann, Lars W.; Graur, Ioana C.; Leipold, William C.; Oberschmidt, James M.; O'Grady, David S.; Regaill, Denis

    1999-07-01

    While the benefits of alternating phase shifted masks in improving lithographic process windows at increased resolution are well known throughout the lithography community, broad implementation of this potentially powerful technique has been slow due to the inherent complexity of the layout design and mask manufacturing process. This paper will review a project undertaken at IBM's Semiconductor Research and Development Center and Mask Manufacturing and Development facility to understand the technical and logistical issues associated with the application of alternating phase shifted mask technology to the gate level of a full microprocessor chip. The work presented here depicts an important milestone toward integration of alternating phase shifted masks into the manufacturing process by demonstrating an automated design solution and yielding a functional alternating phase shifted mask. The design conversion of the microprocessor gate level to a conjugate twin shifter alternating phase shift layout was accomplished with IBM's internal design system that automatically scaled the design, added required phase regions, and resolved phase conflicts. The subsequent fabrication of a nearly defect free phase shifted mask, as verified by SEM based die to die inspection, highlights the maturity of the alternating phase shifted mask manufacturing process in IBM's internal mask facility. Well defined and recognized challenges in mask inspection and repair remain and the layout of alternating phase shifted masks present a design and data preparation overhead, but the data presented here demonstrate the feasibility of designing and building manufacturing quality alternating phase shifted masks for the gate level of a microprocessor.

  15. Model-based mask verification on critical 45nm logic masks

    Science.gov (United States)

    Sundermann, F.; Foussadier, F.; Takigawa, T.; Wiley, J.; Vacca, A.; Depre, L.; Chen, G.; Bai, S.; Wang, J.-S.; Howell, R.; Arnoux, V.; Hayano, K.; Narukawa, S.; Kawashima, S.; Mohri, H.; Hayashi, N.; Miyashita, H.; Trouiller, Y.; Robert, F.; Vautrin, F.; Kerrien, G.; Planchot, J.; Martinelli, C.; Di-Maria, J. L.; Farys, V.; Vandewalle, B.; Perraud, L.; Le Denmat, J. C.; Villaret, A.; Gardin, C.; Yesilada, E.; Saied, M.

    2008-05-01

    In the continuous battle to improve critical dimension (CD) uniformity, especially for 45-nanometer (nm) logic advanced products, one important recent advance is the ability to accurately predict the mask CD uniformity contribution to the overall global wafer CD error budget. In most wafer process simulation models, mask error contribution is embedded in the optical and/or resist models. We have separated the mask effects, however, by creating a short-range mask process model (MPM) for each unique mask process and a long-range CD uniformity mask bias map (MBM) for each individual mask. By establishing a mask bias map, we are able to incorporate the mask CD uniformity signature into our modelling simulations and measure the effects on global wafer CD uniformity and hotspots. We also have examined several ways of proving the efficiency of this approach, including the analysis of OPC hot spot signatures with and without the mask bias map (see Figure 1) and by comparing the precision of the model contour prediction to wafer SEM images. In this paper we will show the different steps of mask bias map generation and use for advanced 45nm logic node layers, along with the current results of this new dynamic application to improve hot spot verification through Brion Technologies' model-based mask verification loop.

  16. 21 CFR 73.1010 - Alumina (dried aluminum hydroxide).

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Alumina (dried aluminum hydroxide). 73.1010 Section 73.1010 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL LISTING OF COLOR ADDITIVES EXEMPT FROM CERTIFICATION Drugs § 73.1010 Alumina (dried...

  17. Textural stability of titania–alumina composite membranes

    NARCIS (Netherlands)

    Kumar, Krishnankutty-Nair P.; Keizer, Klaas; Burggraaf, Anthonie J.

    1993-01-01

    Textural evolution (porosity reduction, pore and crystallite growth) in titania–alumina composite membranes has been studied using thermal analysis, X-ray diffraction, field emission scanning electron microscopy and N2 physisorption techniques. The presence of alumina in the membranes improved the t

  18. Chemical modification/grafting of mesoporous alumina with polydimethylsiloxane (PDMS)

    NARCIS (Netherlands)

    Pinheiro de Melo, A.F.; Nijmeijer, A.; Sripathi, V.G.P.; Winnubst, A.J.A.

    2015-01-01

    A method for polydimethylsiloxane grafting of alumina powders is described which involves chemical modification of the surface of mesoporous (5 nm) γ-alumina flakes with a linker (3-aminopropyltriethoxysilane: APTES), either by a solution phase (SPD) or a vapour phase (VPD) reaction, followed by PDM

  19. Chemical modification/grafting of mesoporous alumina with polydimethylsiloxane (PDMS)

    NARCIS (Netherlands)

    Pinheiro de Melo, A.F.; Nijmeijer, Arian; Sripathi, V.G.P.; Winnubst, Aloysius J.A.

    2015-01-01

    A method for polydimethylsiloxane grafting of alumina powders is described which involves chemical modification of the surface of mesoporous (5 nm) γ-alumina flakes with a linker (3-aminopropyltriethoxysilane: APTES), either by a solution phase (SPD) or a vapour phase (VPD) reaction, followed by

  20. Development of Reproducing Alumina-Magnesia-Carbon Bricks

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The reproducing alumina-magnesia-carbon bricks were prepared with the dumped bricks as starting materials. The bulk density, apparent porosity, crushing strength, modolus of rupture and slag resistance of the specimen were analyzed. The results show that the used refractories can be reused and recycled by the right method. The reproducing alumina-magnesia-carbon bricks with better abilities were prepared.

  1. 40 CFR 721.10120 - Siloxane modified alumina nanoparticles (generic).

    Science.gov (United States)

    2010-07-01

    ... nanoparticles (generic). 721.10120 Section 721.10120 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Specific Chemical Substances § 721.10120 Siloxane modified alumina nanoparticles (generic). (a) Chemical... as siloxane modified alumina nanoparticles (PMN P-05-687) is subject to reporting under this...

  2. Dynamic compressive and tensile strengths of spark plasma sintered alumina

    Science.gov (United States)

    Girlitsky, I.; Zaretsky, E.; Kalabukhov, S.; Dariel, M. P.; Frage, N.

    2014-06-01

    Fully dense submicron grain size alumina samples were manufactured from alumina nano-powder using Spark Plasma Sintering and tested in two kinds of VISAR-instrumented planar impact tests. In the first kind, samples were loaded by 1-mm tungsten impactors, accelerated to a velocity of about 1 km/s. These tests were aimed at studying the Hugoniot elastic limit (HEL) of Spark Plasma Sintering (SPS)-processed alumina and the decay, with propagation distance, of the elastic precursor wave. In the tests of the second kind, alumina samples of 3-mm thickness were loaded by 1-mm copper impactors accelerated to 100-1000 m/s. These tests were aimed at studying the dynamic tensile (spall) strength of the alumina specimens. The tensile fracture of the un-alloyed alumina shows a monotonic decline of the spall strength with the amplitude of the loading stress pulse. Analysis of the decay of the elastic precursor wave allowed determining the rate of the irreversible (inelastic) strains in the SPS-processed alumina at the initial stages of the shock-induced inelastic deformation and to clarify the mechanisms responsible for the deformation. The 1-% addition of Cr2O3 decreases the HEL of the SPS-processed alumina by 5-% and its spall strength by 50% but barely affects its static properties.

  3. Shadows Alter Facial Expressions of Noh Masks

    Science.gov (United States)

    Kawai, Nobuyuki; Miyata, Hiromitsu; Nishimura, Ritsuko; Okanoya, Kazuo

    2013-01-01

    Background A Noh mask, worn by expert actors during performance on the Japanese traditional Noh drama, conveys various emotional expressions despite its fixed physical properties. How does the mask change its expressions? Shadows change subtly during the actual Noh drama, which plays a key role in creating elusive artistic enchantment. We here describe evidence from two experiments regarding how attached shadows of the Noh masks influence the observers’ recognition of the emotional expressions. Methodology/Principal Findings In Experiment 1, neutral-faced Noh masks having the attached shadows of the happy/sad masks were recognized as bearing happy/sad expressions, respectively. This was true for all four types of masks each of which represented a character differing in sex and age, even though the original characteristics of the masks also greatly influenced the evaluation of emotions. Experiment 2 further revealed that frontal Noh mask images having shadows of upward/downward tilted masks were evaluated as sad/happy, respectively. This was consistent with outcomes from preceding studies using actually tilted Noh mask images. Conclusions/Significance Results from the two experiments concur that purely manipulating attached shadows of the different types of Noh masks significantly alters the emotion recognition. These findings go in line with the mysterious facial expressions observed in Western paintings, such as the elusive qualities of Mona Lisa’s smile. They also agree with the aesthetic principle of Japanese traditional art “yugen (profound grace and subtlety)”, which highly appreciates subtle emotional expressions in the darkness. PMID:23940748

  4. Mask process correction (MPC) modeling and its application to EUV mask for electron beam mask writer EBM-7000

    Science.gov (United States)

    Kamikubo, Takashi; Ohnishi, Takayuki; Hara, Shigehiro; Anze, Hirohito; Hattori, Yoshiaki; Tamamushi, Shuichi; Bai, Shufeng; Wang, Jen-Shiang; Howell, Rafael; Chen, George; Li, Jiangwei; Tao, Jun; Wiley, Jim; Kurosawa, Terunobu; Saito, Yasuko; Takigawa, Tadahiro

    2010-09-01

    In electron beam writing on EUV mask, it has been reported that CD linearity does not show simple signatures as observed with conventional COG (Cr on Glass) masks because they are caused by scattered electrons form EUV mask itself which comprises stacked heavy metals and thick multi-layers. To resolve this issue, Mask Process Correction (MPC) will be ideally applicable. Every pattern is reshaped in MPC. Therefore, the number of shots would not increase and writing time will be kept within reasonable range. In this paper, MPC is extended to modeling for correction of CD linearity errors on EUV mask. And its effectiveness is verified with simulations and experiments through actual writing test.

  5. Thermal Conductivity of Alumina-reinforced Zirconia Composites

    Science.gov (United States)

    Bansal, Narottam P.

    2005-01-01

    10-mol% yttria-stabilized zirconia (10SZ) - alumina composites containing 0-30 mol% alumina were fabricated by hot pressing at 1500 C in vacuum. Thermal conductivity was determined at various temperatures using a steady-state laser heat flux technique. Thermal conductivity of the composites increased with increase in alumina content. Composites containing 0, 5, and 10-mol% alumina did not show any change in thermal conductivity with temperature. However, those containing 20 and 30-mol% alumina showed a decrease in thermal conductivity with increase in temperature. The measured values of thermal conductivity were in good agreement with those calculated from the Maxwell-Eucken model where one phase is uniformly dispersed within a second major continuous phase.

  6. Thermal shock behavior of rare earth modified alumina ceramic composites

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Junlong; Liu, Changxia [Ludong Univ., Yantai (China). School of Transportation

    2017-05-15

    Alumina matrix ceramic composites toughened by AlTiC master alloys, diopside and rare earths were fabricated by hot-pressing and their thermal shock behavior was investigated and compared with that of monolithic alumina. Results showed that the critical thermal shock temperature (ΔT) of monolithic alumina was 400 C. However, it decreased to 300 C for alumina incorporating only AlTiC master alloys, and increased with further addition of diopside and rare earths. Improvement of thermal shock resistance was obtained for alumina ceramic composites containing 9.5 wt.% AlTiC master alloys and 0.5 wt.% rare earth additions, which was mainly attributed to the formation of elongated grains in the composites.

  7. Comparison of deep desulfurization methods in alumina production process

    Institute of Scientific and Technical Information of China (English)

    刘战伟; 李旺兴; 马文会; 尹中林; 武国宝

    2015-01-01

    Several methods of deep desulfurization in alumina production process were studied, and the costs of these methods were compared. It is found that most of the S2− in sodium aluminate solution can be removed by adding sodium nitrate or hydrogen peroxide in digestion process, and in this way the effect of S2− on alumina product quality is eliminated. However, the removal efficiency of2-23SOin sodium aluminate solution is very low by this method. Both S2− and2-23SO in sodium aluminate solution can be removed completely by wet oxidation method in digestion process. The cost of desulfurization by wet oxidation is lower than by adding sodium nitrate or hydrogen peroxide. The results of this research reveal that wet oxidation is an economical and feasible method for the removal of sulfur in alumina production process to improve alumina quality, and provide valuable guidelines for alumina production by high-sulfur bauxite.

  8. Thermal Shock Behaviour of Alumina-Iron Composites

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Thermal shock behaviour was investigated for two morphologically different composites comprising an alumina matrix and 20 vol. pct Fe particles for a wide range of quenching temperature differences (△T=100~800°C) and compared to a monolithic alumina. The retained strength and critical quenching temperature difference, △Tc, of the two composites were a significant improvement over the values for the respective monolithic alumina. Crack lengths and densities were shown to be greater for the alumina than for the two composites at all quenching temperature differences. The thermal shock resistance parameters for monolithic alumina and the two composites were calculated according to their mechanical and physical properties. The calculated results agree well with the experimental one and indicate possible explanations for the differences in thermal shock behaviour.

  9. Ge nanocrystals with highly uniform size distribution deposited on alumina at room temperature by pulsed laser deposition: structural, morphological, and charge trapping properties

    Energy Technology Data Exchange (ETDEWEB)

    Martin-Sanchez, J., E-mail: javier.martin.nano@gmail.com; Marques, L.; Vieira, E. M. F. [University of Minho, Department of Physics and Centre of Physics (Portugal); Doan, Q. T.; Marchand, A.; El Hdiy, A. [LMEN, Universite de Reims Champagne-Ardenne (France); Rolo, A. G.; Pinto, S. R. C.; Ramos, M. M. D.; Chahboun, A.; Gomes, M. J. M. [University of Minho, Department of Physics and Centre of Physics (Portugal)

    2012-05-15

    In this work, we report on the synthesis of Ge nanocrystals (NCs) by pulsed laser deposition (PLD) at room temperature (RT) in an argon atmosphere without any further annealing process. Our results show that functional thin films of crystalline Ge nanoparticles with spherical shapes can be obtained by PLD directly on alumina layers deposited on n-doped Si (100) substrates. In addition, we also demonstrate that a uniform size distribution of NCs with an average diameter of about 3 nm and a density of 2.3 Multiplication-Sign 10{sup 11} cm{sup -2} can be obtained by optimizing a shadow mask set-up, where a solid disk is introduced between the target and the substrate. Charge/discharge effects in Ge NCs deposited on a high-k amorphous alumina layer are also evidenced by conductive atomic force microscopy, which makes them suitable for memory applications.

  10. Photo- and electroluminescence properties of lanthanide tungstate-doped porous anodic aluminum oxide

    Science.gov (United States)

    Staninski, Krzysztof; Piskuła, Zbigniew; Kaczmarek, Małgorzata

    2017-02-01

    A new cathode material for the potential use in light-emitting devices, based on porous anodic alumina (PAA), aluminum and ITO layers has been synthesized. Porous alumina samples with ordered pore arrays were prepared electrochemically from high purity Al sheet in H2SO4 and H3PO4. To be able to apply the matrix obtained in the electroluminescence cell, the thickness of the barrier layer of aluminum oxide was decreased by slow reduction of the anodization voltage to zero. The luminescence and electroluminescence (EL) properties of the Al2O3 matrix admixtured with Eu3+ and Tb3+ ions as well as europium and terbium tungstates, were determined. The particles of inorganic luminophore were synthesized on the walls of the matrix cylindrical nanopores in the two-step process of immersion in solutions of TbCl3 or EuCl3 and Na2WO4. The effect of the nanopores diameter and the thickness of the porous Al2O3 layer on the intensity and relative yield of electroluminescence was analyzed, the best results were obtained for 80-90 μm PAA layers with 140 nm nanopores.

  11. Masking the Feeling of Being Stupid.

    Science.gov (United States)

    Smith, Sally L.

    1988-01-01

    Teaching experience at The Lab School of Washington has shown that learning-disabled children and adults cope with their lack of self-esteem and feelings of stupidity by developing masks to hide their hurt. These include masks of super-competence, helplessness, invisibility, clowning, injustice collecting, indifference, boredom, outrageousness,…

  12. Masked hypertension, a review of the literature.

    NARCIS (Netherlands)

    Verberk, W.J.; Thien, Th.; Leeuw, P.W. de

    2007-01-01

    Masked hypertension (blood pressure that is normal in the physicians' office but elevated elsewhere) is a common phenomenon as prevalence among studies varies from 8 to 45% and is seen at all ages. large discrepancies, however, exist between studies that have dealt with masked hypertension. It is of

  13. Computing Challenges in Coded Mask Imaging

    Science.gov (United States)

    Skinner, Gerald

    2009-01-01

    This slide presaentation reviews the complications and challenges in developing computer systems for Coded Mask Imaging telescopes. The coded mask technique is used when there is no other way to create the telescope, (i.e., when there are wide fields of view, high energies for focusing or low energies for the Compton/Tracker Techniques and very good angular resolution.) The coded mask telescope is described, and the mask is reviewed. The coded Masks for the INTErnational Gamma-Ray Astrophysics Laboratory (INTEGRAL) instruments are shown, and a chart showing the types of position sensitive detectors used for the coded mask telescopes is also reviewed. Slides describe the mechanism of recovering an image from the masked pattern. The correlation with the mask pattern is described. The Matrix approach is reviewed, and other approaches to image reconstruction are described. Included in the presentation is a review of the Energetic X-ray Imaging Survey Telescope (EXIST) / High Energy Telescope (HET), with information about the mission, the operation of the telescope, comparison of the EXIST/HET with the SWIFT/BAT and details of the design of the EXIST/HET.

  14. A facial mask comprising Dead Sea mud.

    Science.gov (United States)

    Abu-Jdayil, Basim; Mohameed, Hazim A

    2006-01-01

    Many investigators have proved that Dead Sea salt and mud are useful in treating skin disorders and skin diseases. Therefore, the black mud has been extensively used as a base for the preparation of soaps, creams, and unguents for skin care. This study concerns a facial mask made mainly of Dead Sea mud. The effects of temperature and shearing conditions on the rheological behavior of the facial mask were investigated. The mud facial mask exhibited a shear thinning behavior with a yield stress. It was found that the apparent viscosity of the mask has a strong dependence on the shear rate as well as on the temperature. The facial mask exhibited a maximum yield stress and very shear thinning behavior at 40 degrees C, which is attributed to the gelatinization of the polysaccharide used to stabilize the mud particles. On the other hand, the mud mask exhibited a time-independent behavior at low temperatures and shear rates and changed to a thixotropic behavior upon increasing both the temperature and the shear rate. The shear thinning and thixotropic behaviors have a significant importance in the ability of the facial mask to spread on the skin: the Dead Sea mud mask can break down for easy spreading, and the applied film can gain viscosity instantaneously to resist running. Moreover, particle sedimentation, which in this case would negatively affect consumer acceptance of the product, occurs slowly due to high viscosity at rest conditions.

  15. [Use of respiratory masks in healthcare workers].

    Science.gov (United States)

    Ciotti, C; Bouvet, E; Abiteboul, D

    2008-08-01

    Two different types of filtering respiratory masks are available in healthcare settings. The first ones are used to protect patients from droplets coming from the mouth of healthcare workers (HCW) and the second ones are protective masks. For the moment, we lack information regarding application of Ministry of Health recommendations and on adherence of HCW to mask use. Geres, the HCW exposure risk study group, and the INRS, are now conducting a survey in several hospitals in France to evaluate the use of respiratory masks in healthcare settings. Two phases are planned. Phase I is a self survey using a questionnaire for occupational doctors and hygienists and phase II includes three steps on HCW behavior: evaluation of knowledge and practice concerning respiratory masks, evaluation of respiratory mask use, evaluation of wear and fit test in a context of airborne isolation with a FFP1 and FFP2 respiratory mask. Phase I is finished and phase II is beginning. The first phase I data show that the Ministry's recommendations are observed: respiratory masks are available, written recommendations are present; information and training are organized for healthcare workers. Phase II results are not available yet.

  16. EUV mask pilot line at Intel Corporation

    Science.gov (United States)

    Stivers, Alan R.; Yan, Pei-Yang; Zhang, Guojing; Liang, Ted; Shu, Emily Y.; Tejnil, Edita; Lieberman, Barry; Nagpal, Rajesh; Hsia, Kangmin; Penn, Michael; Lo, Fu-Chang

    2004-12-01

    The introduction of extreme ultraviolet (EUV) lithography into high volume manufacturing requires the development of a new mask technology. In support of this, Intel Corporation has established a pilot line devoted to encountering and eliminating barriers to manufacturability of EUV masks. It concentrates on EUV-specific process modules and makes use of the captive standard photomask fabrication capability of Intel Corporation. The goal of the pilot line is to accelerate EUV mask development to intersect the 32nm technology node. This requires EUV mask technology to be comparable to standard photomask technology by the beginning of the silicon wafer process development phase for that technology node. The pilot line embodies Intel's strategy to lead EUV mask development in the areas of the mask patterning process, mask fabrication tools, the starting material (blanks) and the understanding of process interdependencies. The patterning process includes all steps from blank defect inspection through final pattern inspection and repair. We have specified and ordered the EUV-specific tools and most will be installed in 2004. We have worked with International Sematech and others to provide for the next generation of EUV-specific mask tools. Our process of record is run repeatedly to ensure its robustness. This primes the supply chain and collects information needed for blank improvement.

  17. Catalytic cleavage of lignin β-O-4 link mimics using copper on alumina and magnesia-alumina

    NARCIS (Netherlands)

    Strassberger, Z.; Alberts, A.H.; Louwerse, M.J.; Tanase, S.; Rothenberg, G.

    2013-01-01

    Copper on γ-alumina and on mixed magnesia-alumina, Cu/MgO-Al2O3, catalyse the hydrodeoxygenation (HDO) of β-O-4 lignin-type dimers, giving valuable aromatics. The typical selectivity to phenol is as high as 20%. By changing the support's acidity we can modify the dispersion of copper. Interestingly,

  18. Properties of Transition Metal Doped Alumina

    Science.gov (United States)

    Nykwest, Erik; Limmer, Krista; Brennan, Ray; Blair, Victoria; Ramprasad, Rampi

    Crystallographic texture can have profound effects on the properties of a material. One method of texturing is through the application of an external magnetic field during processing. While this method works with highly magnetic systems, doping is required to couple non-magnetic systems with the external field. Experiments have shown that low concentrations of rare earth (RE) dopants in alumina powders have enabled this kind of texturing. The magnetic properties of RE elements are directly related to their f orbital, which can have as many as 7 unpaired electrons. Since d-block elements can have as many as 5 unpaired electrons the effects of substitutional doping of 3d transition metals (TM) for Al in alpha (stable) and theta (metastable) alumina on the local structure and magnetic properties, in addition to the energetic cost, have been calculated by performing first-principles calculations based on density functional theory. This study has led to the development of general guidelines for the magnetic moment distribution at and around the dopant atom, and the dependence of this distribution on the dopant atom type and its coordination environment. It is anticipated that these findings can aid in the selection of suitable dopants help to guide parallel experimental efforts. This project was supported in part by an internship at the Army Research Laboratory, administered by the Oak Ridge Institute for Science and Education, along with a grant of computer time from the DoD High Performance Computing Modernization Program.

  19. Modified-starch Consolidation of Alumina Ceramics

    Institute of Scientific and Technical Information of China (English)

    JU Chenhui; WANG Yanmin; YE Jiandong; HUANG Yun

    2008-01-01

    The alumina ceramics with the homogeneous microstructure and the higher density were fabricated via the modified-starch consolidation process by 1.0 wt%of a modified starch as a consolidator/binder.The swelling behavior of the modified oxidized tapioca starch was analyzed by optical microscope,and two other corn starches(common corn starch and high amylose COrn starch)were also analyzed for comparison.The modified starch used as a binder for the consolidation swelled at about 55℃.began to gelatinize at 65℃ and then was completely gelatinized at 75℃.But the corn starches could not be completely gelatinized even at 80℃for 1 h.The high-strength green bodies(10.6 MPa)with the complex shapes were produced.The green bodies were sintered without any binder burnout procedure at 1700℃and a relative density of 95.3% was obtained for the sintered bodies,which is similar to that of the sintered sample formed by conventional slip casting.In addition,the effect of temperature on the apparent viscosity of the starch/alumina slurry in the process was investigated,and the corresponding mechanism for the starch consolidation was discussed.

  20. Extinction controlled adaptive phase-mask coronagraph

    CERN Document Server

    Bourget, P; Mawet, D; Haguenauer, P

    2012-01-01

    Context. Phase-mask coronagraphy is advantageous in terms of inner working angle and discovery space. It is however still plagued by drawbacks such as sensitivity to tip-tilt errors and chromatism. A nulling stellar coronagraph based on the adaptive phase-mask concept using polarization interferometry is presented in this paper. Aims. Our concept aims at dynamically and achromatically optimizing the nulling efficiency of the coronagraph, making it more immune to fast low-order aberrations (tip-tilt errors, focus, ...). Methods. We performed numerical simulations to demonstrate the value of the proposed method. The active control system will correct for the detrimental effects of image instabilities on the destructive interference. The mask adaptability both in size, phase and amplitude also compensates for manufacturing errors of the mask itself, and potentially for chromatic effects. Liquid-crystal properties are used to provide variable transmission of an annulus around the phase mask, but also to achieve t...

  1. Parsing abnormal grain growth in specialty aluminas

    Science.gov (United States)

    Lawrence, Abigail Kremer

    Grain growth in alumina is strongly affected by the impurities present in the material. Certain impurity elements are known to have characteristic effects on abnormal grain growth in alumina. Specialty alumina powders contain multiple impurity species including MgO, CaO, SiO2, and Na 2O. In this work, sintered samples made from alumina powders containing various amounts of the impurities in question were characterized by their grain size and aspect ratio distributions. Multiple quantitative methods were used to characterize and classify samples with varying microstructures. The grain size distributions were used to partition the grain size population into subpopulations depending on the observed deviation from normal behavior. Using both grain size and aspect ratio a new visual representation for a microstructure was introduced called a morphology frequency map that gives a fingerprint for the material. The number of subpopulations within a sample and the shape of the distribution on the morphology map provided the basis for a classification scheme for different types of microstructures. Also using the two parameters a series of five metrics were calculated that describe the character of the abnormal grains in the sample, these were called abnormal character values. The abnormal character values describe the fraction of grains that are considered abnormal, the average magnitude of abnormality (including both grain size and aspect ratio), the average size, and variance in size. The final metric is the correlation between grain size and aspect ratio for the entire population of grains. The abnormal character values give a sense of how different from "normal" the sample is, given the assumption that a normal sample has a lognormal distribution of grain size and a Gaussian distribution of aspect ratios. In the second part of the work the quantified measures of abnormality were correlated with processing parameters such as composition and heat treatment conditions. A

  2. Adsorption on Highly Ordered Porous Alumina

    Science.gov (United States)

    Mistura, Giampaolo; Bruschi, Lorenzo; Lee, Woo

    2016-10-01

    Porous anodic aluminum oxide (AAO) is characterized by a regular arrangement of the pores with a narrow pore size distribution over extended areas, uniform pore depth, and solid pore walls without micropores. Thanks to significant improvements in anodization techniques, structural engineering of AAO allows to accurately tailor the pore morphology. These features make porous AAO an excellent substrate to study adsorption phenomena. In this paper, we review recent experiments involving the adsorption in porous AAO. Particular attention will be devoted to adsorption in straight and structured pores with a closed end which shed new light on fundamental issues like the origin of hysteresis in closed end pores and the nature of evaporation from ink-bottle pores. The results will be compared to those obtained in other synthetic materials like porous silicon and silica.

  3. DEVELOPMENT OF TECHNOLOGY FOR ANODE BALL PRODUCTION

    Directory of Open Access Journals (Sweden)

    G. V. Kozhevnikova

    2015-01-01

    Full Text Available Technology of copper anode balls manufacturing by means of cross-wedge rolling method is developed. The technology satisfies the requirements towards anode balls’ crystalline structure, form and geometrical dimensions accuracy.

  4. STUDY OF ANODIC OVERVOLTAGE IN NEODYMIUM ELECTROLYSIS

    Institute of Scientific and Technical Information of China (English)

    K.R. Liu; J.S. Chen; Q. Han; X.J. Wei

    2003-01-01

    The anodic overvoltage of neodymium electrolysis was determined by slow scanning oscillogram. The effects of some factors, i.e. the temperature, the anodic current density, the concentration of Nd2O3 and the components of the electrolyte were investigated and the approaches to decrease the anodic overvoltage were also discussed. The results show that the anodic overvoltage increases with the anodic current density and decreases with the increasing temperature. The linear relation between the anodic overvoltage and the current density corresponding to Tafel equation is determined to some extent. The anodic overvoltage decreases with the increasing concentrations of LiF and NdF3. It also decreases by controlling the anodic current density properly, increasing the temperature or the concentrations of LiF and NdF3 and the reducing polar distance.

  5. One-step fabrication of nanostructure-covered microstructures using selective aluminum anodization based on non-uniform electric field

    Science.gov (United States)

    Park, Yong Min; Kim, Byeong Hee; Seo, Young Ho

    2016-06-01

    This paper presents a selective aluminum anodization technique for the fabrication of microstructures covered by nanoscale dome structures. It is possible to fabricate bulging microstructures, utilizing the different growth rates of anodic aluminum oxide in non-uniform electric fields, because the growth rate of anodic aluminum oxide depends on the intensity of electric field, or current density. After anodizing under a non-uniform electric field, bulging microstructures covered by nanostructures were fabricated by removing the residual aluminum layer. The non-uniform electric field induced by insulative micropatterns was estimated by computational simulations and verified experimentally. Utilizing computational simulations, the intensity profile of the electric field was calculated according to the ratio of height and width of the insulative micropatterns. To compare computational simulation results and experimental results, insulative micropatterns were fabricated using SU-8 photoresist. The results verified that the shape of the bottom topology of anodic alumina was strongly dependent on the intensity profile of the applied electric field, or current density. The one-step fabrication of nanostructure-covered microstructures can be applied to various fields, such as nano-biochip and nano-optics, owing to its simplicity and cost effectiveness.

  6. Mask tuning for process window improvement

    Science.gov (United States)

    Buttgereit, Ute; Birkner, Robert; Graitzer, Erez; Cohen, Avi; Triulzi, Benedetta; Romeo, Carmelo

    2011-03-01

    For the next years optical lithography stays at 193nm with a numerical aperture of 1.35. Mask design becomes more complex, mask and lithography specifications tighten. The k1 factor comes close to 0.25 which leads to a tremendously increased Mask Error Enhancement Factor (MEEF). This means that CD errors on mask are getting highly amplified on wafer. Process control becomes more important than ever. Accurate process control is a key factor to success to maintain a high yield in chip production. One key parameter to ensure a high and reliable functionality for any integrated circuit is the critical dimension uniformity (CDU). There are different contributors which impact the intra-field CD performance at wafer such as mask CD uniformity, scanner fingerprint, resist process etc. In the present work we focus on improvement of mask CD signature which is one of the main contributors to intra-field CD uniformity. The mask CD uniformity has been measured by WLCD32 which measures the CD based on proven aerial image technology. Based on this CD input the CD uniformity was corrected by CDC200TM and afterwards verified by WLCD32 measurement. The CDC200TM tool utilizes an ultrafast femto-second laser to write intra-volume shading elements (Shade-In ElementsTM) inside the bulk material of the mask. By adjusting the density of the shading elements, the light transmission through the mask is locally changed in a manner that improves wafer CDU when the corrected mask is printed. Additionally, the impact of the improved CD uniformity on the lithography process window was investigated. Goal of the work is to establish a process flow for mask CD uniformity improvement based on mask CD metrology by WLCD32 and mask CD uniformity control by CDC200TM and to verify its impact on the lithography process window. The proposed process flow will be validated by wafer prints. It was shown that the WLCD32 has an excellent correlation to wafer data and an outstanding CD repeatability. It provides

  7. Masking property of quantum random cipher with phase mask encryption

    Science.gov (United States)

    Sohma, Masaki; Hirota, Osamu

    2014-10-01

    The security analysis of physical encryption protocol based on coherent pulse position modulation (CPPM) originated by Yuen is one of the most interesting topics in the study of cryptosystem with a security level beyond the Shannon limit. Although the implementation of CPPM scheme has certain difficulty, several methods have been proposed recently. This paper deals with the CPPM encryption in terms of symplectic transformation, which includes a phase mask encryption as a special example, and formulates a unified security analysis for such encryption schemes. Specifically, we give a lower bound of Eve's symbol error probability using reliability function theory to ensure that our proposed system exceeds the Shannon limit. Then we assume the secret key is given to Eve after her heterodyne measurement. Since this assumption means that Eve has a great advantage in the sense of the conventional cryptography, the lower bound of her error indeed ensures the security level beyond the Shannon limit. In addition, we show some numerical examples of the security performance.

  8. Fabrication of Alumina Nanowires from Porous Alumina Membranes by Etching in Phosphoric Acid Solution

    Science.gov (United States)

    Wang, Xuehua; Li, Chengyong; Ma, Lianjiao; Cao, Hong; Zhang, Baohua

    Alumina nanowires (ANWs) with high aspect ratios were synthesized by the chemical etching of porous alumina membranes (PAMs) in phosphoric acid solution. The morphology and structure of ANWs were analyzed by SEM and XRD, respectively. The results showed that the typical features of ANWs are around 35 nm in diameter and around 20 μm in length, the crystalline structure of the ANWs was amorphous, which was in accordance with that of the PAMs. Furthermore, the morphology of the PAMs was characterized by AFM and SEM in detail. On the basis of AFM and SEM observations, a possible formation mechanism of ANWs was discussed, and the inhomogeneous of the dissolution between the triple points and the side walls was considered to be the essential factor deciding the formation of ANWs.

  9. Microstructural evolution of alumina-zirconia nanocomposites; Evolucao microestrutural de nanocompositos alumina-zirconia

    Energy Technology Data Exchange (ETDEWEB)

    Ojaimi, C.L.; Chinelatto, A.S.A.; Chinelatto, A.L. [Universidade Estadual de Ponta Grossa (UEPG), PR (Brazil); Pallone, E.M.J.A., E-mail: christianelago@yahoo.com.br [Universidade de Sao Paulo (USP), Pirassununga, Sao Paulo, SP (Brazil). Faculdade de Zootecnia e Engenharia de Alimentos

    2012-07-01

    Ceramic materials have limited use due to their brittleness. The inclusion of nanosized particles in a ceramic matrix, which are called nanocomposites, and ceramic processing control by controlling the grain size and densification can aid in obtaining ceramic products of greater strength and toughness. Studies showed that the zirconia nano inclusions in the matrix of alumina favors an increase in mechanical properties by inhibiting the grain growth of the matrix and not by the mechanism of the transformation toughening phase of zirconia. In this work, the microstructural evolution of alumina nanocomposites containing 15% by volume of nanometric zirconia was studied. From the results it was possible to understand the sintering process of these nanocomposites. (author)

  10. Deformation Behaviour of Coarse Grain Alumina under Shock Loading

    Science.gov (United States)

    Gupta, Satish

    2013-06-01

    To develop better understanding of the shock wave induced deformation behavior of coarse grain alumina ceramics, and for measurement of its Hugoniot Elastic Limit (HEL), in-situ and recovery gas gun experiments have been carried out on coarse grain alumina (grain size ~ 10 μm), prepared in the form of discs (>99.9% TMD) by pressure-less sintering of alpha alumina powder at 1583 K. The HEL value of 1.9 GPa has been determined from the kink in the pressure history recorded using piezoresistance gauge and also from the free surface velocity history of the sample shocked to 9 GPa. The nano-indentation measurements on the alumina samples shocked to 6.5 GPa showed hardness value 15% lower than 21.3 GPa for unshocked alumina, and strong Indentation Size Effect (ISE); the hardness value was still lower and the ISE was stronger for the sample shocked to 12 GPa. The XRD measurements showed reduced particle size and increased microstrains in the shocked alumina fragments. SEM, FESEM and TEM measurements on shock treated samples showed presence of grain localized micro- and nano-scale deformations, micro-cleavages, grain-boundary microcracks, extensive shear induced deformations, and localized micro-fractures, etc. These observations led to the development of a qualitative model for the damage initiation and its subsequent growth mechanisms in shocked alumina. The work performed in collaboration with K.D. Joshi of BARC and A.K. Mukhopadhyay of CGCRI.

  11. Dissolution kinetics for alumina in cryolite melts. Distribution of alumina in the electrolyte of industrial aluminium cells

    Energy Technology Data Exchange (ETDEWEB)

    Kobbeltvedt, Ove

    1997-12-31

    This thesis contributes to the understanding of which factors determine the rate of dissolution of alumina added to the bath in alumina reduction cells. Knowing this may help reduce the occurrences of operation interruptions and thus make it possible to produce aluminium using less energy. When alumina powder was added to a stirred cryolite melt, the alumina dissolved in two distinct main stages. In the first stage, the dissolution rate was very high, which reflects dissolution of single alumina grains that are being dispersed in the bath upon addition. In the second stage, lumps of alumina infiltrated with bath dissolved at a rate considerably slower than that of the first stage. The formation of these alumina agglomerates is the most important contributor to slow dissolution. The parameters varied in the experiments were convection, batch size, and temperature of the bath and of the added alumina. Increased gas stirring of the bath speeded up dissolution in both stages but the size of the batch was of little significance. Increasing the bath temperature had no effect in the first stage but speeded up dissolution considerably in the second stage. Compared to adding alumina at room temperature, preheating it to a high temperature (600 {sup o}C) increased the dissolution rate in the first stage while preheating to lower temperatures (100-300 {sup o}C) decreased the dissolution rate. In the second stage, preheating slowed the dissolution. The two latter phenomena of reduced dissolution rates are ascribed to the removal of moisture from the alumina upon preheating. The bath flow and the distribution of alumina in the bath were measured in four different types of cells. It was found that if a certain asymmetry of the magnetic field traverse to the cell was present, due to the presence of risers, then loops of high velocity bath flow occurred near the short ends of the cell. Thus, alumina added near the short ends is effectively transferred away from the feeding

  12. Space and time in masking and crowding.

    Science.gov (United States)

    Lev, Maria; Polat, Uri

    2015-01-01

    Masking and crowding are major phenomena associated with contextual modulations, but the relationship between them remains unclear. We have recently shown that crowding is apparent in the fovea when the time available for processing is limited, pointing to the strong relationship between crowding in the spatial and temporal domains. Models of crowding emphasize the size (acuity) of the target and the spacing between the target and flankers as the main determinants that predict crowding. Our model, which is based on lateral interactions, posits that masking and crowding are related in the spatial and temporal domains at the fovea and periphery and that both can be explained by the increasing size of the human perceptive field (PF) with increasing eccentricity. We explored the relations between masking and crowding using letter identification and contrast detection by correlating the crowding effect with the estimated size of the PF and with masking under different spatiotemporal conditions. We found that there is a large variability in PF size and crowding effects across observers. Nevertheless, masking and crowding were both correlated with the estimated size of the PF in the fovea and periphery under a specific range of spatiotemporal parameters. Our results suggest that under certain conditions, crowding and masking share common neural mechanisms that underlie the spatiotemporal properties of these phenomena in both the fovea and periphery. These results could explain the transfer of training gains from spatiotemporal Gabor masking to letter acuity, reading, and reduced crowding.

  13. Intact crowding and temporal masking in dyslexia.

    Science.gov (United States)

    Doron, Adi; Manassi, Mauro; Herzog, Michael H; Ahissar, Merav

    2015-01-01

    Phonological deficits in dyslexia are well documented. However, there is an ongoing discussion about whether visual deficits limit the reading skills of people with dyslexia. Here, we investigated visual crowding and backward masking. We presented a Vernier (i.e., two vertical bars slightly offset to the left or right) and asked observers to indicate the offset direction. Vernier stimuli are visually similar to letters and are strongly affected by crowding, even in the fovea. To increase task difficulty, Verniers are often followed by a mask (i.e., backward masking). We measured Vernier offset discrimination thresholds for the basic Vernier task, under crowding, and under backward masking, in students with dyslexia (n = 19) and age and intelligence matched students (n = 27). We found no group differences in any of these conditions. Controls with fast visual processing (good backward masking performance), were faster readers. By contrast, no such correlation was found among the students with dyslexia, suggesting that backward masking does not limit their reading efficiency. These findings indicate that neither elevated crowding nor elevated backward masking pose a bottleneck to reading skills of people with dyslexia.

  14. Pupil Masks for Spectrophotometry of Transiting Exoplanets

    Science.gov (United States)

    Itoh, Satoshi; Matsuo, Taro; Goda, Shohei; Shibai, Hiroshi; Sumi, Takahiro

    2017-09-01

    Spectrophotometric stability, which is crucial in the spectral characterization of transiting exoplanets, is affected by photometric variations arising from field-stop loss in space telescopes with pointing jitter or primary mirror deformation. This paper focuses on a new method for removing slit-loss or field-stop-loss photometric variation through the use of a pupil mask. Two types of pupil function are introduced: the first uses conventional (e.g., Gaussian or hyper-Gaussian) apodizing patterns; whereas the second, which we call a block-shaped mask, employs a new type of pupil mask designed for high photometric stability. A methodology for the optimization of a pupil mask for transit observations is also developed. The block-shaped mask can achieve a photometric stability of 10-5 for a nearly arbitrary field-stop radius when the pointing jitter is smaller than approximately 0.7λ /D and a photometric stability of 10-6 at a pointing jitter smaller than approximately 0.5λ /D. The impact of optical aberrations and mask imperfections upon mask performance is also discussed.

  15. Mask industry assessment trend analysis: 2012

    Science.gov (United States)

    Chan, Y. David

    2012-02-01

    Microelectronics industry leaders consistently cite the cost and cycle time of mask technology and mask supply among the top critical issues for lithography. A survey was designed by SEMATECH with input from semiconductor company mask technologists and merchant mask suppliers to objectively assess the overall conditions of the mask industry. With the continued support of the industry, this year's assessment was the tenth in the current series of annual reports. This year's survey is basically the same as the 2005 through 2011 surveys. Questions are grouped into six categories: General Business Profile Information, Data Processing, Yields and Yield Loss Mechanisms, Delivery Times, Returns, and Services. Within each category is a multitude of questions that ultimately produce a detailed profile of both the business and technical status of the critical mask industry. We received data from 11 companies this year, which was a record high since the beginning of the series. The responding companies represented more than 96% of the volume shipped and about 90% of the 2011 revenue for the photomask industry. These survey reports are often used as a baseline to gain perspective on the technical and business status of the mask and microelectronics industries. They will continue to serve as a valuable reference to identify strengths and opportunities. Results can also be used to guide future investments in critical path issues.

  16. Ballistic Performance of Alumina and Zirconia-toughened Alumina Against 7.62 Armour Piercing Projectile

    Directory of Open Access Journals (Sweden)

    S G. Savio

    2014-09-01

    Full Text Available A study was carried out to compare the ballistic performance of high purity alumina and zirconia-toughened alumina (ZTA using depth of penetration (DoP test configuration against 7.62 mm armour piercing (AP ammunition. The effect of tile thickness on the differential efficiency factor (DEF was studied for tile thickness in the range of 3 mm to 6 mm for alumina tiles and 3 mm to 5 mm for ZTA tiles. The DEF is found to increase as tile thickness increases. An analysis on the failed shots showed that the residual shot weight does not follow a single linear relationship with ceramic tile thickness unlike the residual DoP for all thicknesses of tiles. Post-ballistic analysis on ceramic powder for particle size distribution was carried out and the results are presented.Defence Science Journal, Vol. 64, No. 5, September 2014, pp.477-483, DOI:http://dx.doi.org/10.14429/dsj.64.6745

  17. Neopuff T-piece mask resuscitator: is mask leak related to watching the pressure dial?

    Science.gov (United States)

    Tracy, Mark B; Klimek, J; Shingde, V; Hinder, M; Maheshwari, R; Tracy, S K

    2010-09-01

    The aim of the study is to compare mask leak and delivered ventilation during Neopuff (NP) mask ventilation in two modes: (i) with NP pressure dial hidden and resuscitator watching chest wall (CW) rise with, (ii) CW movement hidden and resuscitator watching NP pressure dial. Thirty-six participants gave mask ventilation to a modified manikin designed to measure mask leak and delivered ventilation for two minutes in each mode randomly assigned. Paired t-tests were used to analyse differences in mean values. Linear regression was used to determine the association of mask leak with delivered ventilation. Of 7277 inflations analysed, 3621 were observing chest wall mode (CWM) and 3656 observing NP mode (NPM). Mask leak was similar between the groups; 31.6% for CWM and 31.5% (p = 0.56) for NPM. There were no significant differences in airways pressures and expired tidal volumes (TVe) between modes. Mask leak was strongly associated with TVe (R = -0.86 p mask leak is not greater when resuscitators watch the NP pressure dial. Mask leak is related to TVe. Mask ventilation training with manikins should include tidal volume measurements. © 2010 The Author(s)/Journal Compilation © 2010 Foundation Acta Paediatrica.

  18. Anode sheath transition in an anodic arc for synthesis of nanomaterials

    Science.gov (United States)

    Nemchinsky, V. A.; Raitses, Y.

    2016-06-01

    The arc discharge with ablating anode or so-called anodic arc is widely used for synthesis of nanomaterials, including carbon nanotubes and fullerens, metal nanoparticles etc. We present the model of this arc, which confirms the existence of the two different modes of the arc operation with two different anode sheath regimes, namely, with negative anode sheath and with positive anode sheath. It was previously suggested that these regimes are associated with two different anode ablating modes—low ablation mode with constant ablation rate and the enhanced ablation mode (Fetterman et al 2008 Carbon 46 1322). The transition of the arc operation from low ablation mode to high ablation mode is determined by the current density at the anode. The model can be used to self-consistently determine the distribution of the electric field, electron density and electron temperature in the near-anode region of the arc discharge. Simulations of the carbon arc predict that for low arc ablating modes, the current is driven mainly by the electron diffusion to the anode. For positive anode sheath, the anode voltage is close to the ionization potential of anode material, while for negative anode sheath, the anode voltage is an order of magnitude smaller. It is also shown that the near-anode plasma, is far from the ionization equilibrium.

  19. Design and fabrication of alumina micro reciprocating engine

    Institute of Scientific and Technical Information of China (English)

    JIN Peng; GAO Yu-long; LIU Nan; JIANG Kylie

    2008-01-01

    Microengines are regarded as the potential replacements for batteries. Aimed at the unsatisfactory thermal property of silicon used in the combustion chambers, ceramics are chosen as the construction material in this paper. The fabrication process where alumina has been chosen as the microengine material is discussed. Vigorous FEA has been carried out, and it is found that the material satisfies the stress and deformation require-ments of the design. Then the alumina fabrication process is described. Soft reusable polydimethylsiloxane (PDMS) moulds are produced from SU-8 resist masters, and alumina microengine parts are produced using the PDMS moulds. Images of the ceramic components show that the fabrication satisfies the design requirements.

  20. Processing of silicon nitride and alumina nanosize powders

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez, E.J.; Piermarini, G.; Hockey, B.; Malghan, S.G. [National Inst. of Standard and Technology, Gaithersburg, MD (United States)

    1995-08-01

    The effects of pressure on the compaction and subsequent processing of nanosize {gamma} alumina powders were studied. A 3 mm diameter piston/cylinder die was used to compact the nanosize powders to pressures of 1 and 2.5 GPa. The green bodies were sintered at temperatures up to 1600{degrees}C. Results show that green body density can be increased by higher compaction pressures. It appears that as a result of the {gamma}-to-{alpha} transformation in alumina, higher green density does not necessarily produce a higher density sintered alumina body. The microstructures of the sintered bodies are described in terms of porosity and phase content.

  1. Alumina Paste Sublimation Suppression Barrier for Thermoelectric Device

    Science.gov (United States)

    Paik, Jong-Ah (Inventor); Caillat, Thierry (Inventor)

    2014-01-01

    Alumina as a sublimation suppression barrier for a Zintl thermoelectric material in a thermoelectric power generation device operating at high temperature, e.g. at or above 1000K, is disclosed. The Zintl thermoelectric material may comprise Yb.sub.14MnSb.sub.11. The alumina may be applied as an adhesive paste dried and cured on a substantially oxide free surface of the Zintl thermoelectric material and polished to a final thickness. The sublimation suppression barrier may be finalized by baking out the alumina layer on the Zintl thermoelectric material until it becomes substantially clogged with ytterbia.

  2. Special requirements for alumina ceramic of ESG electrode bowl

    Institute of Scientific and Technical Information of China (English)

    ZHANG Jun-an; XUE Kai; ZHANG Jia-tai; ZHANG Qiang

    2004-01-01

    At present ESG (Electrostatic Suspended Gyro) is the most precise inertia element in the world. The electrode bowl, which has direct effect on the precision of ESG, is a key part to ESG. Through the analysis of the function and characteristic of the electrode bowl in hollow rotor ESG and the present situation of new material development in the world, the alumina ceramic is regarded as the best material for the electrode bowl of hollow rotor ESG. By analyzing the present situation of alumina ceramic in the world, main technique requirements have been put forward for the alumina ceramic of ESG electrode bowl which is also fit for solid rotor ESG.

  3. Wenshan’s 800,000-ton Alumina Project Completed

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    <正>On September 26,2012,the completion ceremony of the 800,000-ton alumina project was held at the alumina factory in Matang Industrial Park, Wenshan city,Yunnan.Wenshan’s 800,000-ton alumina project and its supporting mining construction projects have been listed as one of 20 major industrial construction projects of Yunnan. The project covers an area of approximately 5,500 mu,with an estimated total investment of RMB 4,987 million. It is invested and built

  4. Ellipsometry of anodic film growth

    Energy Technology Data Exchange (ETDEWEB)

    Smith, C.G.

    1978-08-01

    An automated computer interpretation of ellisometer measurements of anodic film growth was developed. Continuous mass and charge balances were used to utilize more fully the time dependence of the ellipsometer data and the current and potential measurements. A multiple-film model was used to characterize the growth of films which proceeds via a dissolution--precipitation mechanism; the model also applies to film growth by adsorption and nucleation mechanisms. The characteristic parameters for film growth describe homogeneous and heterogeneous crystallization rates, film porosities and degree of hydration, and the supersaturation of ionic species in the electrolyte. Additional descriptions which may be chosen are patchwise film formation, nonstoichiometry of the anodic film, and statistical variations in the size and orientation of secondary crystals. Theories were developed to describe the optical effects of these processes. An automatic, self-compensating ellipsometer was used to study the growth in alkaline solution of anodic films on silver, cadmium, and zinc. Mass-transport conditions included stagnant electrolyte and forced convection in a flow channel. Multiple films were needed to characterize the optical properties of these films. Anodic films grew from an electrolyte supersatuated in the solution-phase dissolution product. The degree of supersaturation depended on transport conditions and had a major effect on the structure of the film. Anodic reaction rates were limited by the transport of charge carriers through a primary surface layer. The primary layers on silver, zinc, and cadmium all appeared to be nonstoichiometric, containing excess metal. Diffusion coefficients, transference numbers, and the free energy of adsorption of zinc oxide were derived from ellipsometer measurements. 97 figures, 13 tables, 198 references.

  5. Ellipsometry of anodic film growth

    Energy Technology Data Exchange (ETDEWEB)

    Smith, C.G.

    1978-08-01

    An automated computer interpretation of ellisometer measurements of anodic film growth was developed. Continuous mass and charge balances were used to utilize more fully the time dependence of the ellipsometer data and the current and potential measurements. A multiple-film model was used to characterize the growth of films which proceeds via a dissolution--precipitation mechanism; the model also applies to film growth by adsorption and nucleation mechanisms. The characteristic parameters for film growth describe homogeneous and heterogeneous crystallization rates, film porosities and degree of hydration, and the supersaturation of ionic species in the electrolyte. Additional descriptions which may be chosen are patchwise film formation, nonstoichiometry of the anodic film, and statistical variations in the size and orientation of secondary crystals. Theories were developed to describe the optical effects of these processes. An automatic, self-compensating ellipsometer was used to study the growth in alkaline solution of anodic films on silver, cadmium, and zinc. Mass-transport conditions included stagnant electrolyte and forced convection in a flow channel. Multiple films were needed to characterize the optical properties of these films. Anodic films grew from an electrolyte supersatuated in the solution-phase dissolution product. The degree of supersaturation depended on transport conditions and had a major effect on the structure of the film. Anodic reaction rates were limited by the transport of charge carriers through a primary surface layer. The primary layers on silver, zinc, and cadmium all appeared to be nonstoichiometric, containing excess metal. Diffusion coefficients, transference numbers, and the free energy of adsorption of zinc oxide were derived from ellipsometer measurements. 97 figures, 13 tables, 198 references.

  6. Porous Alumina Based Capacitive MEMS RH Sensor

    CERN Document Server

    Juhasz, L; Timar-Horvath, Veronika; Desmulliez, Marc; Dhariwal, Resh

    2008-01-01

    The aim of a joint research and development project at the BME and HWU is to produce a cheap, reliable, low-power and CMOS-MEMS process compatible capacitive type relative humidity (RH) sensor that can be incorporated into a state-of-the-art, wireless sensor network. In this paper we discuss the preparation of our new capacitive structure based on post-CMOS MEMS processes and the methods which were used to characterize the thin film porous alumina sensing layer. The average sensitivity is approx. 15 pF/RH% which is more than a magnitude higher than the values found in the literature. The sensor is equipped with integrated resistive heating, which can be used for maintenance to reduce drift, or for keeping the sensing layer at elevated temperature, as an alternative method for temperature-dependence cancellation.

  7. Aluminum matrix composites reinforced with alumina nanoparticles

    CERN Document Server

    Casati, Riccardo

    2016-01-01

    This book describes the latest efforts to develop aluminum nanocomposites with enhanced damping and mechanical properties and good workability. The nanocomposites exhibited high strength, improved damping behavior and good ductility, making them suitable for use as wires. Since the production of metal matrix nanocomposites by conventional melting processes is considered extremely problematic (because of the poor wettability of the nanoparticles), different powder metallurgy routes were investigated, including high-energy ball milling and unconventional compaction methods. Special attention was paid to the structural characterization at the micro- and nanoscale, as uniform nanoparticle dispersion in metal matrix is of prime importance. The aluminum nanocomposites displayed an ultrafine microstructure reinforced with alumina nanoparticles produced in situ or added ex situ. The physical, mechanical and functional characteristics of the materials produced were evaluated using different mechanical tests and micros...

  8. Crystallography of Alumina-YAG-Eutectic

    Science.gov (United States)

    Farmer, Serene C.; Sayir, Ali; Dickerson, Robert M.; Matson, Lawrence E.

    2000-01-01

    Multiple descriptions of the alumina-YAG eutectic crystallography appear in the ceramic literature. The orientation between two phases in a eutectic system has direct impact on residual stress, morphology, microstructural stability, and high temperature mechanical properties. A study to demonstrate that the different crystallographic relationships can be correlated with different growth constraints was undertaken. Fibers produced by Laser-Heated Float Zone (LHFZ) and Edge-defined Film-fed Growth (EFG) were examined. A map of the orientation relationship between Al2O3 and Y3Al5O12 and their relationship to the fiber growth axis as a function of pull rate are presented. Regions in which a single orientation predominates are identified.

  9. Fracture simulation for zirconia toughened alumina microstructure

    CERN Document Server

    Kim, Kyungmok; Forest, Bernard

    2013-01-01

    Purpose - The purpose of this paper is to describe finite element modelling for fracture and fatigue behaviour of zirconia toughened alumina microstructures. Design/methodology/approach - A two-dimensional finite element model is developed with an actual $Al{_2}O{_3}$ - 10 vol% $ZrO{_2}$ microstructure. A bilinear, time-independent cohesive zone law is implemented for describing fracture behaviour of grain boundaries. Simulation conditions are similar to those found at contact between a head and a cup of hip prosthesis. Residual stresses arisen from the mismatch of thermal coefficient between grains are determined. Then, effects of a micro-void and contact stress magnitude are investigated with models containing residual stresses. For the purpose of simulating fatigue behaviour, cyclic loadings are applied to the models. Findings - Results show that crack density is gradually increased with increasing magnitude of contact stress or number of fatigue cycles. It is also identified that a micro-void brings about...

  10. Printed shadow masks for organic transistors

    Science.gov (United States)

    Noguchi, Yoshiaki; Sekitani, Tsuyoshi; Someya, Takao

    2007-09-01

    We have manufactured organic field-effect transistors by using shadow masks that are patterned by a screen printing system. The 50-nm-thick pentacene layer is sublimed as a channel in the vacuum system through the shadow mask on the base film with a multilayer patterned by ink-jet. After the deposition of the pentacene layer, the shadow mask is peeled off from the base film without any mechanical damages to the lower structures. The mobility in the saturation regime is 0.4cm2/Vs and the on-off ratio exceeds 105.

  11. Characterization of Glasses in One Type of Alumina Rich Fly Ash by Chemical Digestion Methods: Implications for Alumina Extraction

    Directory of Open Access Journals (Sweden)

    Lijun Zhao

    2016-01-01

    Full Text Available In recent years, one type of alumina rich fly ash (ARFA with about 50 wt% of alumina has been extensively investigated for alumina extraction in China. Due to the silica in ARFA, alumina extraction would have to generate a huge amount of solid waste. There is a growing interest in the glasses in ARFA, because they are composed mainly of silica and could be removed prior to alumina extraction. In this work, the glasses in ARFA have been investigated by chemical methods, that is, acid and base digestions. The chemical compositions have been measured by XRF for ARFA from the digestion processes. The K2O standard, XRD, and FTIR spectroscopies were successfully used to define the digestions processes, and size analysis and SEM-EDX provided rich information on particle transformations. As a result, acid and base digestion methods were found to produce very similar results for the glasses in ARFA. The K2O standard was attributed to the formation of glasses by illites, and TiO2 and Fe2O3 were proposed to originate from ilmenite in alumina rich coals (ARC. Some implications of the results were also discussed for the alumina extraction from ARFA.

  12. Tom Pickering as a clinical scientist: masked hypertension.

    Science.gov (United States)

    Eguchi, Kazuo

    2010-04-01

    Masked hypertension has been 'unmasked' by the use of the out-of-office measurement of blood pressure, as home BP monitoring or ambulatory blood pressure monitoring has become available. The term masked hypertension could be used more widely than the original version of masked hypertension; morning hypertension, stress-induced hypertension, and nocturnal hypertension are all classified as subtypes of masked hypertension. Masked hypertension can also be seen in patients with diabetes, that could change clinical practice in diabetes. Masked hypertension is associated with cardiovascular events, but most of the outcome studies are on antihypertensive medications. Therefore, masked hypertension includes insufficient treatment of hypertension. In Dr Pickering's latest review of masked hypertension, prehypertension or high normal blood pressure was stressed as an associating factor with masked hypertension. The biggest theme in the field of hypertension is how we can detect masked hypertension. I present two interesting cases of possible masked hypertension in this commentary.

  13. [Vernier Anode Design and Image Simulation].

    Science.gov (United States)

    Zhao, Ai-rong; Ni, Qi-liang; Song, Ke-fei

    2015-12-01

    Based-MCP position-sensitive anode photon-counting imaging detector is good at detecting extremely faint light, which includes micro-channel plate (MCP), position-sensitive anode and readout, and the performances of these detectors are mainly decided by the position-sensitive anode. As a charge division anode, Vernier anode using cyclically varying electrode areas which replaces the linearly varying electrodes of wedge-strip anode can get better resolution and greater electrode dynamic range. Simulation and design of the Vernier anode based on Vernier's decode principle are given here. Firstly, we introduce the decode and design principle of Vernier anode with nine electrodes in vector way, and get the design parameters which are the pitch, amplitude and the coarse wavelength of electrode. Secondly, we analyze the effect of every design parameters to the imaging of the detector. We simulate the electron cloud, the Vernier anode and the detector imaging using Labview software and get the relationship between the pitch and the coarse wavelength of the anode. Simultaneously, we get the corresponding electron cloud for the designing parameters. Based on the result of the simulation and the practical machining demand, a nine electrodes Vernier anode was designed and fabricated which has a pitch of 891 µm, insulation width of 25 µm, amplitude of 50 µm, coarse pixel numbers of 5.

  14. Electrocatalysis of carbon anode in aluminium electrolysis

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The anodic overvoltage of the carbon anode in aluminum electrolysis isof the order of 0.6 V at normal current densities. However, it can be reduced somewhat by doping the anode carbon with various inorganic compounds. A new apparatus was designed to improve the precision of overvoltage measurements. Anodes were doped with MgAl2O4 and AlF3 both by impregnation of the coke and by adding powder, and the measured overvoltage was compared with that of undoped samples. For prebake type anodes baked at around 1150 oC, the anodic overvoltage was reduced by 40-60 mV, and for Soderberg type anodes, baked at 950 oC, by 60-80 mV.

  15. A study of defects on EUV mask using blank inspection, patterned mask inspection, and wafer inspection

    Energy Technology Data Exchange (ETDEWEB)

    Huh, S.; Ren, L.; Chan, D.; Wurm, S.; Goldberg, K. A.; Mochi, I.; Nakajima, T.; Kishimoto, M.; Ahn, B.; Kang, I.; Park, J.-O.; Cho, K.; Han, S.-I.; Laursen, T.

    2010-03-12

    The availability of defect-free masks remains one of the key challenges for inserting extreme ultraviolet lithography (EUVL) into high volume manufacturing. yet link data is available for understanding native defects on real masks. In this paper, a full-field EUV mask is fabricated to investigate the printability of various defects on the mask. The printability of defects and identification of their source from mask fabrication to handling were studied using wafer inspection. The printable blank defect density excluding particles and patterns is 0.63 cm{sup 2}. Mask inspection is shown to have better sensitivity than wafer inspection. The sensitivity of wafer inspection must be improved using through-focus analysis and a different wafer stack.

  16. Phase separation of a binary liquid in anodic aluminium oxide templates: a structural study by small angle neutron scattering.

    Science.gov (United States)

    Lefort, R; Duvail, J-L; Corre, T; Zhao, Y; Morineau, D

    2011-07-01

    The radial nanostructure of the binary liquid triethylamine/water confined in 60 nm diameter independent cylindrical pores of anodic aluminium oxide membranes is studied by small angle neutron scattering. It is shown that composition inhomogeneities are present in the confined mixtures well below the bulk critical point. An analysis of the neutron scattering form factor reveals the existence of an adsorbed water layer of a few nanometers at the liquid/alumina interface, coexisting with a TEA-rich phase in the core.

  17. Polishing Your Transparencies: Mounting, Masking, Overlays.

    Science.gov (United States)

    Jobe, Holly; Cannon, Glenn

    This brief guide discusses the mounting of overhead transparencies on frames, the types of mounts, the proper masking for presentation, and the use of overlays. Numerous line drawings provide the reader with a helpful visual reference. (RAO)

  18. Effects of Anode Wettability and Slots on Anodic Bubble Behavior Using Transparent Aluminium Electrolytic Cells

    Science.gov (United States)

    Zhao, Zhibin; Gao, Bingliang; Feng, Yuqing; Huang, Yipeng; Wang, Zhaowen; Shi, Zhongning; Hu, Xianwei

    2017-02-01

    Transparent aluminum electrolytic cells were used to study the effects of anode wettability and slots on bubble behavior in a similar environment to that used in industrial cells. Observations were conducted using two types of transparent cells, one with side-observation and the other with a bottom-observation cell design. Anodic bubbles rising process in the side channel is strongly affected by the wettability of the anode. After rising a short distance, the bubbles detach from the anode vertical surface at good-wetting anode cases, while the bubbles still attach to the vertical surface at poor-wetting anode cases. Anode slots of width of 4 mm are able to prevent smaller bubbles from coalescing into larger bubbles and thus decrease the bubble size and gas coverage on the anode. Anode slots also make a contribution in slightly reducing bubble thickness. With the presence of slots, the bubble-induced cell voltage oscillation decreases as well.

  19. Fabrication and anodic polarization behavior of lead-based porous anodes in zinc electrowinning

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    A new type of lead-based porous anode in zinc electrowinning was prepared by negative pressure infiltration.The anodie polarization potential and corrosion rate were studied and compared with those of traditional fiat anodes (Pb-0.8%Ag) used in industry.The anode eorrosion rate was determined by anode actual current density and microstructure.The results show that the anodic oxygen evolution potential decreases first and then increases with the decrease of pore diameter.The anodic potential decreases to the lowest value of 1.729 V at the pore diameter of 1.25-1.60 mm.The porous anode can decrease its actual current density and thus decrease the anodic corrosion rate.When the pore diameter is 1.60-2.00 mm,the anodic relative corrosion rate reaches the lowest value of 52.1%.

  20. High Alumina Refractory Mortars GB/T 2994-2008

    Institute of Scientific and Technical Information of China (English)

    Wang Jing; Chai Junlan

    2009-01-01

    @@ 1 Scope This standard specifies the classification, techni-cal requirements, test methods, quality appraisal pro-cedure, packing, marking, transportation, storage and quality certificate of high alumina refractory mortars.

  1. Direct spray pyrolysis of aluminum chloride solution for alumina preparation

    Institute of Scientific and Technical Information of China (English)

    吕国志; 张廷安; 王龙; 马思达; 豆志河; 刘燕

    2014-01-01

    The effects of pyrolysis mode and pyrolysis parameters on Cl content in alumina were investigated, and the alumina products were characterized by XRD, SEM and ASAP. The experimental results indicate that the spray pyrolysis efficiency is higher than that of static pyrolysis process, and the reaction and evaporation process lead to a multi-plot state of the alumina products by spray pyrolysis. Aluminum phase starts to transform intoγ-Al2O3 at spray pyrolysis temperature of 600 °C, which is about 200 °C lower than that of static pyrolysis process. The primary particle size of γ-Al2O3 product is 27.62 nm, and Cl content in alumina products is 0.38%at 800 °C for 20 min.

  2. Fused Cast Alumina Refractory Products for Glass Tank Furnace

    Institute of Scientific and Technical Information of China (English)

    SHEN Keyin

    2006-01-01

    @@ 1 Subject and Scope The standard specifies the requirement, testing method, inspection rule and requirements for the labeling, packing, shipping and storing of the fused cast alumina refractory products for glass tanks.

  3. High Alumina Refractory Bricks for Electric Arc Furnace Roofs

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    @@ 1 Scope This standard specifies the sort, technical requirement, test method, inspection rules, marking, packing, transportation, storage and quality certification of high alumina refractory bricks for electric arc furnace roofs.

  4. Superhydrophobic alumina surface based on stearic acid modification

    Energy Technology Data Exchange (ETDEWEB)

    Feng Libang, E-mail: lepond@hotmail.com [School of Mechatronic Engineering, Lanzhou Jiaotong University, Lanzhou 730070 (China); Zhang Hongxia; Mao Pengzhi; Wang Yanping; Ge Yang [School of Mechatronic Engineering, Lanzhou Jiaotong University, Lanzhou 730070 (China)

    2011-02-15

    A novel superhydrophobic alumina surface is fabricated by grafting stearic acid layer onto the porous and roughened aluminum film. The chemical and phase structure, morphology, and the chemical state of the atoms at the superhydrophobic surface were investigated by techniques as FTIR, XRD, FE-SEM, and XPS, respectively. Results show that a super water-repellent surface with a contact angle of 154.2{sup o} is generated. The superhydrophobic alumina surface takes on an uneven flowerlike structure with many nanometer-scale hollows distribute in the nipple-shaped protrusions, and which is composed of boehmite crystal and {gamma}-Al{sub 2}O{sub 3}. Furthermore, the roughened and porous alumina surface is coated with a layer of hydrophobic alkyl chains which come from stearic acid molecules. Therefore, both the roughened structure and the hydrophobic layer endue the alumina surface with the superhydrophobic behavior.

  5. Synthesis of beta alumina from aluminum hydroxide and oxyhydroxide precursors

    CSIR Research Space (South Africa)

    Van Zyl, A

    1993-02-01

    Full Text Available Two aluminium oxyhydroxides, boehmite and pseudoboehmite, and two aluminium hydroxides, bayerite and gibbsite, have been investigated as precursors for the synthesis of the solid electrolyte, beta alumina. Reaction pathways and products have been...

  6. Role of mask in asian shamanism

    OpenAIRE

    POVALYASHKO GALINA; ABAYEVA SABINA

    2015-01-01

    In the article there is considered a phenomena of shamanism as a cultural universal. Analysis object is a clay mask of National Museum of the Republic of Kazakhstan. It was found in Keder settlement (Kuiryktobe), located in Otrar Oasis at one of the most busy part of the Silk Road. The mask as shamanistic ritual attribute is considered as an obligatory condition for meditative function of shaman.

  7. No masking between test and mask components in perceptually different depth planes.

    Science.gov (United States)

    Hibbeler, Patrick J; Olzak, Lynn A

    2011-01-01

    2-D cues to perceived depth organization have been used to segregate test and mask stimulus components in a discrimination task. Observers made either spatial-frequency or orientation judgments on a rectangular test component by itself or in the presence of constant rectangular masks. There were two basic masking conditions: same-plane or different-plane. In the same-plane conditions, the test components and masks are perceived as existing in the same depth plane. In the different-plane conditions, the test and mask components are perceived to exist in different depth planes. The perception of different depth planes was achieved by using perceived occlusion, which could place either component closer or further from the observer. The results suggest that when test and mask components are separated into different depth planes they no longer influence one another. This effect could be observed in either depth organization, test components in front of the masks or mask components in front of the test. These results indicate that the figure-ground organization of components is not important. Only the designation as existing in the same or different depth planes affects whether or not a mask is effective.

  8. Masked Uncontrolled Hypertension in CKD.

    Science.gov (United States)

    Agarwal, Rajiv; Pappas, Maria K; Sinha, Arjun D

    2016-03-01

    Masked uncontrolled hypertension (MUCH) is diagnosed in patients treated for hypertension who are normotensive in the clinic but hypertensive outside. In this study of 333 veterans with CKD, we prospectively evaluated the prevalence of MUCH as determined by ambulatory BP monitoring using three definitions of hypertension (daytime hypertension ≥135/85 mmHg; either nighttime hypertension ≥120/70 mmHg or daytime hypertension; and 24-hour hypertension ≥130/80 mmHg) or by home BP monitoring (hypertension ≥135/85 mmHg). The prevalence of MUCH was 26.7% by daytime ambulatory BP, 32.8% by 24-hour ambulatory BP, 56.1% by daytime or night-time ambulatory BP, and 50.8% by home BP. To assess the reproducibility of the diagnosis, we repeated these measurements after 4 weeks. Agreement in MUCH diagnosis by ambulatory BP was 75-78% (κ coefficient for agreement, 0.44-0.51), depending on the definition used. In contrast, home BP showed an agreement of only 63% and a κ coefficient of 0.25. Prevalence of MUCH increased with increasing clinic systolic BP: 2% in the 90-110 mmHg group, 17% in the 110-119 mmHg group, 34% in the 120-129 mmHg group, and 66% in the 130-139 mmHg group. Clinic BP was a good determinant of MUCH (receiver operating characteristic area under the curve 0.82; 95% confidence interval 0.76-0.87). In diagnosing MUCH, home BP was not different from clinic BP. In conclusion, among people with CKD, MUCH is common and reproducible, and should be suspected when clinic BP is in the prehypertensive range. Confirmation of MUCH diagnosis should rely on ambulatory BP monitoring.

  9. Recent advances in silica-alumina refractory: A review

    Directory of Open Access Journals (Sweden)

    Chaouki Sadik

    2014-06-01

    Full Text Available In this article, the elaboration and the characterization of silica-alumina refractory have been reviewed. Refractory oxides encompass a broad range of unary, binary, and ternary ceramic compounds that can be used in structural, insulating, and other applications. This paper provides a historical perspective on the elaboration and the use of silica-alumina refractory, reviews applications for refractory oxides, describes typical processing routes, overviews fundamental structure–property relations, and summarizes the properties of these materials.

  10. Electronic Structure of High-Pressure Alumina Polymorphs

    Institute of Scientific and Technical Information of China (English)

    LIU Xiao-Lei; DUAN Wen-Hui; GU Bing-Lin

    2000-01-01

    Electronic properties are investigated for three alumina polymorphs (corundum, Rb2 O3 (Ⅱ) and Pbnm perovskite),which are predicted as the stable structures under different pressure range, by means of the first-principles molecular dynamics method within local density functional framework. The similarity in electronic properties of the polymorphs of alumina is observed. The effect of possible phase transitions on ruby (Cr+3-doped Al2 O3)fluorescences is discussed.

  11. CSL grain boundary distribution in alumina and zirconia ceramics

    OpenAIRE

    Vonlanthen, Pierre; Grobéty, Bernard

    2008-01-01

    The distributions of general and coincidence site lattice (CSL) grain boundaries (GBs) in texture-free alumina and zirconia ceramics sintered at two different temperatures were investigated based on electron backscatter diffraction (EBSD) measurements. Results were compared with the distributions obtained from random 2D spatial models and with calculated random distributions reported in the literature. All alumina samples independent on sintering temperature show the same characteristic devia...

  12. Phase mask coronagraphy at JPL and Palomar

    Directory of Open Access Journals (Sweden)

    Serabyn E.

    2011-07-01

    Full Text Available For the imaging of faint companions, phase mask coronagraphy has the dual advantages of a small inner working angle and high throughput. This paper summarizes our recent work in developing phase masks and in demonstrating their capabilities at JPL. Four-quadrant phase masks have been manufactured at JPL by means of both evaporation and etching, and we have been developing liquid crystal vortex phase masks in partnership with a commercial vendor. Both types of mask have been used with our extreme adaptive optics well-corrected subaperture at Palomar to detect known brown dwarf companions as close as ~ 2.5 λ/D to stars. Moreover, our recent vortex masks perform very well in laboratory tests, with a demonstrated infrared contrast of about 10−6 at 3 λ/D, and contrasts of a few 10−7 with an initial optical wavelength device. The demonstrated performance already meets the needs of ground-based extreme adaptive optics coronagraphy, and further planned improvements are aimed at reaching the 10−10 contrast needed for terrestrial exoplanet detection with a space-based coronagraph.

  13. Claude Levi-Strauss: Mask and Myth

    Directory of Open Access Journals (Sweden)

    Senka Kovač

    2016-02-01

    Full Text Available This paper discuss a relationship between mask and myth and how the appropriate analysis by Claude Levi-Strauss may make clearer a complex field of masks in the part of North America. Claude Levi-Strauss stressed the multi- layered character of myth structure. Similar multi-layered character can be seen at the level of expression, content and meaning of Salish, Kwakiutl and other unique masks of this part of North America. Claude Levi-Strauss analysed certain myths trying to explain ‘the path’ of the masks that belong to the people with similar languages, or those who lived nearby. The mythology of Tsimshian, Tlingit and Haïda people have certain common characteristics that point to the similarities with the nearby groups (Kwakiutl. Despite differences that exist at the level of meanings of the masks, there is also common ‘mythological heritage’ of the people who used to live in the Northern Pacific Coast. Claude Levi-Strauss showed that there is no final solution in the myth analysis, and that there is no possibility that the dissection of the problem will reveal some hidden unity. "As mythical though does not want to start clearly somewhere and come somewhere, it never goes through its whole trajectory: there is always something waiting to be fullfield. The same way as rituals, myths are infinite." It seems that Levi-Strauss explanation of the Path of masks goes in that direction.

  14. VSP wave separation by adaptive masking filters

    Science.gov (United States)

    Rao, Ying; Wang, Yanghua

    2016-06-01

    In vertical seismic profiling (VSP) data processing, the first step might be to separate the down-going wavefield from the up-going wavefield. When using a masking filter for VSP wave separation, there are difficulties associated with two termination ends of the up-going waves. A critical challenge is how the masking filter can restore the energy tails, the edge effect associated with these terminations uniquely exist in VSP data. An effective strategy is to implement masking filters in both τ-p and f-k domain sequentially. Meanwhile it uses a median filter, producing a clean but smooth version of the down-going wavefield, used as a reference data set for designing the masking filter. The masking filter is implemented adaptively and iteratively, gradually restoring the energy tails cut-out by any surgical mute. While the τ-p and the f-k domain masking filters target different depth ranges of VSP, this combination strategy can accurately perform in wave separation from field VSP data.

  15. Uncertainty and confusion in temporal masking

    Science.gov (United States)

    Formby, C.; Zhang, T.

    2001-05-01

    In a landmark study, Wright et al. [Nature 387, 176-178 (1997)] reported an apparent backward-masking deficit in language-impaired children. Subsequently, these controversial results have been influential in guiding treatments for childhood language problems. In this study we revisited Wright et al.'s temporal-masking paradigm to evaluate listener uncertainty effects. Masked detection was measured for 20-ms sinusoids (480, 1000, or 1680 Hz) presented at temporal positions before, during, or after a gated narrowband (W=600-1400 Hz) masker. Listener uncertainty was investigated by cueing various stimulus temporal properties with a 6000-Hz sinusoid presented either ipsi- or contra-lateral to the test ear or bilaterally. The primary cueing effect was measured in the backward-masking condition for a contralateral cue gated simultaneously with the on-frequency 1000-Hz signal. The resulting cued masked-detection threshold was reduced to quiet threshold. No significant cueing effects were obtained for other signal temporal positions in the masker nor for any off-frequency signal conditions. These results indicate that (1) uncertainty can be reduced or eliminated for on-frequency backward masking by cueing the signal and (2) the deficit reported by Wright et al. for language-impaired children may reflect uncertainty and confusion rather than a temporal-processing deficit per se. [Research supported by NIDCD.

  16. Influence of the operating parameters over the current efficiency and corrosion rate in the Hall-Heroult aluminum cell with tin oxide anode substrate material

    Institute of Scientific and Technical Information of China (English)

    Virgil Constantin

    2015-01-01

    A systematic laboratory study was conducted on current efficiency and corrosion obtalned in cryolite–alumina melts with SnO2–Sb2O3–CuO ceramic inert anodes. The current efficiency (CE) was determined by measuring the total amount of oxygen evolved at the anode and was found to be~95%. The influence of operating parameters (inter-elec-trode distance, temperature and current density) was evaluated. The quantitative interdependencies as wel as the ranges of CE optimal values were established (2–3 cm, 940–960 °C and 0.7–0.8 A·cm−2). The corrosion process of these anodes was evaluated by the mass loss method. The evaluation also took care of the corrosion data, as the prob-lem of the anode corrosion appeared to be the maln obstacle for the use of those anodes in the commercial cel s. Low-ering of the ACD up to 2 cm did not aggravate anode corrosion.

  17. Preparation of spherical hollow alumina particles by thermal plasma

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Wonkyung [Department of Chemical Engineering, INHA University, 253 Yonghyun-dong, Nam-gu, Incheon 402‐751 (Korea, Republic of); Regional Innovation Center for Environmental Technology of Thermal Plasma (RIC-ETTP), INHA University, 253 Yonghyun-dong, Nam-gu, Incheon 402‐751 (Korea, Republic of); Choi, Sooseok [Center for Advance Research in Fusion Reactor Engineering, Seoul National University, 599 Gwanak-ro, Gwanak-gu, Seoul 151‐742 (Korea, Republic of); Oh, Seung-Min [Daejoo Electronic Materials Co., 1236‐10 Jeongwang-dong, Siheung-si, Kyunggi-do 429‐848 (Korea, Republic of); Park, Dong-Wha, E-mail: dwpark@inha.ac.kr [Department of Chemical Engineering, INHA University, 253 Yonghyun-dong, Nam-gu, Incheon 402‐751 (Korea, Republic of); Regional Innovation Center for Environmental Technology of Thermal Plasma (RIC-ETTP), INHA University, 253 Yonghyun-dong, Nam-gu, Incheon 402‐751 (Korea, Republic of)

    2013-02-01

    Spherical hollow particles were prepared from solid alumina powders using DC arc thermal plasma, and then spray coating was performed with the as-prepared particles. Operating variables for the hollow particle preparation process were additional plasma gas, input power, and carrier gas flow rate. The spherical hollow alumina particles were produced in the case of using additive gas of H{sub 2} or N{sub 2}, while alumina surface was hardly molten in the pure argon thermal plasma. In addition, the hollow particles were well produced in high power and low carrier gas conditions due to high melting point of alumina. Hollow structure was confirmed by focused ion beam-scanning electron microscopy analysis. Morphology and size distribution of the prepared particles that were examined by field emission-scanning electron microscopy and phase composition of the particles was characterized by X-ray diffraction. In the spray coating process, the as-prepared hollow particles showed higher deposition rate. - Highlights: ► Spherical hollow alumina powder was prepared by non-transferred DC arc plasma. ► Diatomic gasses were added in Ar plasma for high power. ► Prepared hollow alumina powder was efficient for the plasma spray coating.

  18. Adsorption of itaconic acid from aqueous solutions onto alumina

    Directory of Open Access Journals (Sweden)

    JELENA J. GULICOVSKI

    2008-08-01

    Full Text Available Itaconic acid, IA (C5H6O4, was investigated as a potential flocculant for the aqueous processing of alumina powders. The adsorption of IA, as a function of its concentration and pH value of the solution, onto the alumina surface was studied by the solution depletion method. The stability of the suspensions in the presence of itaconic acid was evaluated in light of the surface charge of the alumina powder used, the degree of dissociation of IA, as well as the sedimentation behavior and rheology of the suspensions. It was found that the adsorption process is extremely pH dependent; the maximum adsorption of IA onto alumina surface occurring at a pH close to the value of the first IA dissociation constant, pKa1. Also, IA does not influence the value of the point of zero charge of alumina. It was shown that IA represents an efficient flocculant for concentrated acidic alumina suspensions.

  19. Procoagulant behavior and platelet microparticle generation on nanoporous alumina.

    Science.gov (United States)

    Ferraz, Natalia; Hong, Jaan; Karlsson Ott, Marjam

    2010-05-01

    In the present work, we have investigated platelet microparticle (PMP) generation in whole blood after contact with nanoporous alumina. Alumina membranes with pore sizes of 20 and 200 nm in diameter were incubated with whole blood and the number of PMP in the fluid phase was determined by flow cytometry. The role of the complement system in PMP generation was investigated using an analog of the potent complement inhibitor compstatin. Moreover, the procoagulant activity of the two pore size membranes were compared by measuring thrombin formation. Results indicated that PMP were not present in the fluid phase after whole blood contact with either of the alumina membranes. However, scanning electron microscope micrographs clearly showed the presence of PMP clusters on the 200 nm pore size alumina, while PMP were practically absent on the 20 nm membrane. We probed no influence of complement activation in PMP generation and adhesion and we hypothesize that other specific material-related protein-platelet interactions are taking place. A clear difference in procoagulant activity between the membranes could also be seen, 20 nm alumina showed 100% higher procoagulant activity than 200 nm membrane. By combining surface evaluation and flow cytometry analyses of the fluid phase, we are able to conclude that 200 nm pore size alumina promotes PMP generation and adhesion while the 20 nm membrane does not appreciably cause any release or adhesion of PMP, thus indicating a direct connection between PMP generation and nanoporosity.

  20. Porous alumina and zirconia ceramics with tailored thermal conductivity

    Science.gov (United States)

    Gregorová, E.; Pabst, W.; Sofer, Z.; Jankovský, O.; Matějíček, J.

    2012-11-01

    The thermal conductivity of porous ceramics can be tailored by slip casting and uniaxial dry pressing, using either fugitive pore formers (saccharides) or partial sintering. Porous alumina and zirconia ceramics have been prepared using appropriate powder types (ungranulated for casting, granulated for pressing) and identical firing regimes (but different maximum temperatures in the case of partial sintering). Thermal diffusivities have been measured by the laser- and xenon-flash method and transformed into relative thermal conductivities, which enable a temperature-independent comparison between different materials. While the porosity can be controlled in a similar way for both materials when using pore formers, partial sintering exhibits characteristic differences between alumina and zirconia (for alumina porosities below 45 %, full density above 1600 °C, for zirconia porosities below 60 %, full density above 1300 °C). The different compaction behavior of alumina and zirconia (porosity after pressing 0.465 and 0.597, respectively) is reflected in the fact that for alumina the relative conductivity data of partially sintered materials are below the exponential prediction, while for zirconia they coincide with the latter. Notwithstanding these characteristic differences, for both alumina and zirconia it is possible to tailor the thermal conductivity from 100 % down to approx. 15 % of the solid phase value.

  1. Dynamic yield and tensile strengths of spark plasma sintered alumina

    Science.gov (United States)

    Girlitsky, I.; Zaretsky, E.; Kalabukhov, S.; Dariel, M.; Frage, N.

    2014-05-01

    Fully dense alumina samples with 0.6 μm grain size were produced from alumina powder using Spark Plasma Sintering and tested in two types of VISAR-instrumented planar impact tests. In the tests of the first type the samples of 0.28 to 6-mm thickness were loaded by 1-mm tungsten impactors accelerated up to a velocity of about 1 km/s. These tests were aimed to study the Hugoniot elastic limit (HEL) of the SPS-processed alumina and the decay of the elastic precursor wave with propagation distance. In the second type of test the samples of ~3-mm thickness were loaded by 1-mm copper impactors accelerated up to velocities 100-1000 m/s. These tests were aimed to study the dynamic tensile (spall) strength of the alumina. The data on tensile fracture of the alumina demonstrate a monotonic decline of the spall strength with the amplitude of the loading stress pulse. The data on the decay of the elastic precursor wave allows for determining the rates of the irreversible (inelastic) strains in the SPS-processed alumina at the initial stages of shock-induced inelastic deformation and, thus, to derive some conclusions concerning the mechanisms responsible of the deformation.

  2. Anodic polarographic determination of flucloxacillin.

    Science.gov (United States)

    Squella, J A; Silva, M M; Nuñez-Vergara, L J

    1981-11-01

    The hydrolysis of flucloxacillin at pH 4.9 yields a degradation product which is polarographically oxidizable. This derivative has not been identified, but would seem to contain a thiol group. It gives a diffusion-controlled anodic polarographic wave with a half-wave potential at -0.24 V vs. SCE. The method developed has been applied to the analysis of flucloxacillin capsules, and a recovery of 99% has been obtained.

  3. Influence of additives on the stability of the phases of alumina; Influencia de aditivos na estabilidade das fases da alumina

    Energy Technology Data Exchange (ETDEWEB)

    Rosario, D.C.C.; Gouvea, D., E-mail: deisedorosario@usp.br [Universidade de Sao Paulo (USP), SP (Brazil). Departamento de Engenharia Metalurgica e de Materiais. Laboratorio de Processos Ceramicos

    2011-07-01

    Problems with the stability of gamma alumina in catalytic reactions have been solved with the inclusion of additives during the synthesis of alumina. These additives stabilize the temperature of phase transition allowing the use of metastable alumina at high temperatures, but the mechanisms of action of additives are not well defined. It is known that each family of additive or additives behaves in different ways for this stabilization. This work aimed to study the performance of MgO and ZrO{sub 2}, respectively at different concentrations in alumina synthesized via Pechini. The samples were analyzed by DSC, X-ray diffraction, measurement of specific surface area by BET analysis, and infrared analysis. The results showed an increase in transition temperature for both additives, and a different changes for specific surface area, showing that MgO and ZrO{sub 2} work on improving the stability but with distinct mechanisms. (author)

  4. Clean induced feature CD shift of EUV mask

    Science.gov (United States)

    Nesládek, Pavel; Schedel, Thorsten; Bender, Markus

    2016-05-01

    EUV developed in the last decade to the most promising Second contributor is the fact that EUV mask is currently in contrary to optical mask not yet equipped with sealed pellicle, leading to much higher risk of mask contamination. Third reason is use of EUV mask in vacuum, possibly leading to deposition of vacuum contaminants on the EUV mask surface. Latter reason in combination with tight requirements on backside cleanliness lead to the request of frequent recleaning of the EUV mask, in order to sustain mask lifetime similar to that of optical mask. Mask cleaning process alters slightly the surface of any mask - binary COG mask, as well as phase shift mask of any type and naturally also of the EUV mask as well. In case of optical masks the changes are almost negligible, as the mask is exposed to max. 10-20 re-cleans within its life time. These modifications can be expressed in terms of different specified parameters, e.g. CD shift, phase/trans shift, change of the surface roughness etc. The CD shift, expressed as thinning (or exceptionally thickening) of the dark features on the mask is typically in order of magnitude 0.1nm per process run, which is completely acceptable for optical mask. Projected on the lifetime of EUV mask, assuming 100 clean process cycles, this will lead to CD change of about 10nm. For this reason the requirements for EUV mask cleaning are significantly tighter, << 0.1 nm per process run. This task will look even more challenging, when considering, that the tools for CD measurement at the EUV mask are identical as for optical mask. There is one aspect influencing the CD shift, which demands attention. The mask composition of the EUV mask is significantly different from the optical mask. More precisely there are 2 materials influencing the estimated CD in case of EUV mask, whereas there is one material only in case of optical masks, in first approximation. For optical masks, the CD changes can be attributed to modification of the absorber

  5. Reactions on carbon anodes in aluminium electrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Eidet, Trygve

    1997-12-31

    The consumption of carbon anodes and energy in aluminium electrolysis is higher than what is required theoretically. This thesis studies the most important of the reactions that consume anode materials. These reactions are the electrochemical anode reaction and the airburn and carboxy reactions. The first part of the thesis deals with the kinetics and mechanism of the electrochemical anode reaction using electrochemical impedance spectroscopy. The second part deals with air and carboxy reactivity of carbon anodes and studies the effects of inorganic impurities on the reactivity of carbon anodes in the aluminium industry. Special attention is given to sulphur since its effect on the carbon gasification is not well understood. Sulphur is always present in anodes, and it is expected that the sulphur content of available anode cokes will increase in the future. It has also been suggested that sulphur poisons catalyzing impurities in the anodes. Other impurities that were investigated are iron, nickel and vanadium, which are common impurities in anodes which have been reported to catalyze carbon gasification. 88 refs., 92 figs., 24 tabs.

  6. Use of anodic oxide films to control the diffusion of zinc in GaAs

    Science.gov (United States)

    Cutlerywala, H.; Roedel, R. J.

    1994-06-01

    Experiments were performed to diffuse zinc into GaAs through anodic oxide layers of varying thickness and density. Using electrochemical profiling to determine both the electrically active zinc concentration and the diffusion depth with high resolution, the following results were found. The depth of the junction varies inversely with the thickness and the density of the oxide. However, the surface concentration appears to be independent of oxide thickness or density, attaining a value identical to that found for diffusion into a bare GaAs sample. These results demonstrate that the most significant impact of the oxide is to delay the introduction of the zinc into the GaAs lattice. In short, the anodic oxide cannot be used as either a mask or as a zinc concentration attenuator.

  7. CNTs tuning and vertical alignment in anodic aluminium oxide membrane

    Institute of Scientific and Technical Information of China (English)

    Maria Sarno; Diana Sannino; Caterina Leone; Paolo Ciambelli

    2012-01-01

    Anodic aluminium oxide (AAOM) membranes were used for template growth of carbon nanotubes (CNT) inside their pores by chemical vapour deposition (CVD) of different hydrocarbons,in the absence of transition metal catalyst.A composite material,containing one nanotube for each channel,having the same length as the membrane thickness and the external diameter close to the diameter of the membrane holes,was obtained.Yield,selectivity,and quality of CNTs in terms of diameter (up to very thin CNT),carbon order,length,arrangement (i.e.number of tubes for each channel),purity,that are critical requisites for several applications were optimized by investigating the effect of changing the hydrocarbon feedstock gas,also in the presence of hydrogen.The samples produced using methane as a feedstock have a well ordered structure.The role of the alumina channels surface during the CNT growth has been investigated and its catalytic activity has been proved for the first time.

  8. Effect of alumina composition and surface integrity in alumina/epoxy composites on the ultrasonic attenuation properties.

    Science.gov (United States)

    Cho, Eikhyun; Park, Gwanwoo; Lee, Jae-Wan; Cho, Sung-Min; Kim, Taekyung; Kim, Joongeok; Choi, Wonjoon; Ohm, Won-Suk; Kang, Shinill

    2016-03-01

    We report a method of fabricating backing blocks for ultrasonic imaging transducers, using alumina/epoxy composites. Backing blocks contain scatterers such as alumina particles interspersed in the epoxy matrix for the effective scattering and attenuation of ultrasound. Here, the surface integrity can be an issue, where the composite material may be damaged during machining because of differences in strength, hardness and brittleness of the hard alumina particles and the soft epoxy matrix. Poor surface integrity results in the formation of air cavities between the backing block and the piezoelectric element upon assembly, hence the increased reflection off the backing block and the eventual degradation in image quality. Furthermore, with an issue of poor surface integrity due to machining, it is difficult to increase alumina as scatterers more than a specific mass fraction ratio. In this study, we increased the portion of alumina within epoxy matrix by obtaining an enhanced surface integrity using a net shape fabrication method, and verified that this method could allow us to achieve higher ultrasonic attenuation. Backing blocks were net-shaped with various mass fractions of alumina to characterize the formability and the mechanical properties, including hardness, surface roughness and the internal micro-structure, which were compared with those of machined backing blocks. The ultrasonic attenuation property of the backing blocks was also measured.

  9. In vitro investigation of coupling-agent-free dental restorative composite based on nano-porous alumina fillers.

    Science.gov (United States)

    Thorat, Sanjay B; Diaspro, Alberto; Salerno, Marco

    2014-03-01

    The study aims at demonstrating the feasibility of a novel type of coupling-agent-free resin composite based on nano-porous fillers. The fillers were obtained by ball-milling anodic alumina membranes. Composites were prepared with standard resin at maximum loading of 50% by weight. The resin matrix penetration into the pores was verified visually by scanning electron microscopy and mechanically by atomic force microscopy in force modulation mode. The dynamic flexural modulus at 1Hz was measured by dynamic mechanical analysis. Silver nanoparticles were also synthesized in the pores and their release was investigated with inductive coupled plasma optical emission spectrometry. A storage modulus of 5GPa was measured, similar to the ∼6GPa ones of two coupling-agent-based dental restorative composites used for comparison, which is a promising starting point, additionally showing better one-year equivalent ageing as compared to both commercial materials. Loading the pores with silver nanoparticles was demonstrated as well as their subsequent release in a model system. The alumina micro-particles with interconnected nano-pores allow mechanical interlocking between fillers and matrix without the need for chemical bonding. This material is also promising for being made bio-active, after pore filling with different agents. Copyright © 2013 Elsevier Ltd. All rights reserved.

  10. Optical inspection of EPL stencil masks

    Science.gov (United States)

    Lee, Po-Tung; Engelstad, Roxann L.; Lovell, Edward G.; Kawata, Shintaro; Hirayanagi, Noriyuki; Sogard, Michael R.

    2003-06-01

    We are now at a major junction in lithography where non-optical lithographies, such as Electron Projection Lithography (EPL) [1], are being introduced. The mask used in EPL is a non-transparent silicon substrate with a thin silicon (~2μm) membrane with openings for electrons to pass through acting as a scatterer. This must be inspected as defects may cause printable defects. Initial mask inspection work has used SEM inspection to find these defects. However, we have historically used optical mask inspection tools, utilising wavelengths at or above what we are using for imaging, to qualify masks. This technology has been increasingly difficult to sustain as we have moved from imaging using mercury lamp based sources to pulsed excimer laser based sources that are not very suited to the inspection imaging. Indeed, review of defects found has moved from optical microscopes to SEM based tools. Inspection tools have also evolved, with the first SEM based mask inspection tools being developed to find the smallest defects, however these have the penalty of very low throughput. We will show the potential of using optical systems for the transmissive inspection of these EPL masks. The high potential of existing tools will be shown together with the need for a next generation of inspection tools. We will show that simulations indicate that an inspection source with 193nm wavelength would be required for the detection of 50nm defects on a mask used to print 70nm dense lines. It will also be shown how the position of the defect within the membrane greatly influences detection as well as the implications of moving to a thinner silicon membrane.

  11. The Intervenor Effect in Masked Priming: How Does Masked Priming Survive across an Intervening Word?

    Science.gov (United States)

    Forster, Kenneth I.

    2009-01-01

    Four masked priming experiments are reported investigating the effect of inserting an unrelated word between the masked prime and the target. When the intervening word is visible, identity priming is reduced to the level of one-letter-different form priming, but form priming is largely unaffected. However, when the intervening word is itself…

  12. An etching mask and a method to produce an etching mask

    DEFF Research Database (Denmark)

    2016-01-01

    The present invention relates to an etching mask comprising silicon containing block copolymers produced by self-assembly techniques onto silicon or graphene substrate. Through the use of the etching mask, nanostructures having long linear features having sub-10 nm width can be produced....

  13. The Intervenor Effect in Masked Priming: How Does Masked Priming Survive across an Intervening Word?

    Science.gov (United States)

    Forster, Kenneth I.

    2009-01-01

    Four masked priming experiments are reported investigating the effect of inserting an unrelated word between the masked prime and the target. When the intervening word is visible, identity priming is reduced to the level of one-letter-different form priming, but form priming is largely unaffected. However, when the intervening word is itself…

  14. New anodizing process for magnesium alloys

    Institute of Scientific and Technical Information of China (English)

    LUO Sheng-lian; DAI Lei; ZHOU Hai-hui; CHAI Li-yuan; KUANG Ya-fei

    2006-01-01

    Compact anodic films with high hardness and good corrosion resistance on magnesium alloys were prepared by a new constant voltage and arc-free anodizing process. The effects of anodizing parameters such as applied voltage and electrolyte temperature on the peak current density and the thickness of films were investigated. In addition, the morphologies and corrosion resistance of films were investigated by scanning electron microscopy and potentiodynamic polarization, respectively. The results show that the higher the applied voltage, the higher the peak current density and the thicker the films. However, too high applied voltage may result in breakdown of films and intense sparking which may deteriorate the properties of the anodic films and bring about unsafety. The new anodizing process can be applied in a wide range of temperature. The new anodic films have numbers of pores with the diameter of 0.5 - 5.0 μm which do not transverse the entire film.

  15. Cast alumina forming austenitic stainless steels

    Energy Technology Data Exchange (ETDEWEB)

    Muralidharan, Govindarajan; Yamamoto, Yukinori; Brady, Michael P

    2013-04-30

    An austenitic stainless steel alloy consisting essentially of, in terms of weight percent ranges 0.15-0.5C; 8-37Ni; 10-25Cr; 2.5-5Al; greater than 0.6, up to 2.5 total of at least one element selected from the group consisting of Nb and Ta; up to 3Mo; up to 3Co; up to 1W; up to 3Cu; up to 15Mn; up to 2Si; up to 0.15B; up to 0.05P; up to 1 total of at least one element selected from the group consisting of Y, La, Ce, Hf, and Zr; <0.3Ti+V; <0.03N; and, balance Fe, where the weight percent Fe is greater than the weight percent Ni, and wherein the alloy forms an external continuous scale comprising alumina, and a stable essentially single phase FCC austenitic matrix microstructure, the austenitic matrix being essentially delta-ferrite free and essentially BCC-phase-free. A method of making austenitic stainless steel alloys is also disclosed.

  16. Nanoparticle assisted coagulation of aqueous alumina suspensions

    Directory of Open Access Journals (Sweden)

    Abdullah Fatih Çetinel

    2012-02-01

    Full Text Available Colloidal processing of ceramics offers a high potential to achieve homogeneous microstructures with improved material properties. In this study, a novel forming method is investigated, which was already applied successfully for the fabrication of ceramic matrix composites (CMC, but is also considered to be a suitable direct casting technique for the fabrication of advanced ceramics with tailored microstructure and properties. The so-called nanoparticle assisted coagulation method (NPAC represents a modification of the hydrolysis-assisted solidification (HAS technique. It promises green components with high green strength, uniform density as well as homogeneous and tailored microstructure. Electrostatically stabilized colloidal suspensions with high solid loadings were produced by dispersing various fractions of submicron alumina powder and aluminium hydroxide nano-powder in water without use of any organic binder. Rheology and coagulation kinetics of suspensions and green part properties were studied regarding to modifications of pH value, setting temperature, amount of setting agent, amount of nano-powder, solids loading and process parameters like ultrasound treatment. It could be revealed that the homogeneous core-shell arrangement of submicron and nanoparticles in the colloidal state can be transmitted to the green state, which improves the microstructure and green density of the green parts. For this, the NPAC method is seen as a promising technique for the fabrication of advanced ceramics with tailored microstructure and properties.

  17. Mechanical properties of alumina porcelain during heating

    Science.gov (United States)

    Šín, Peter; Podoba, Rudolf; ŠtubÅa, Igor; Trník, Anton

    2014-11-01

    The mechanical strength and Young's modulus of green alumina porcelain (50 wt. % of kaolin, 25 wt. % of Al2O3, and 25 wt. % of feldspar) were measured during heating up to 900 °C and 1100 °C, respectively. To this end, we used the three point-bending method and modulated force thermomechanical analysis (mf-TMA). The loss liberation - of the physically bound water (20 - 250 °C) strengthens the sample and Young's modulus increases its values significantly. The dehydroxylation that takes place in the range of 400 - 650 °C causes a slight decrease in Young's modulus. On the other hand, the mechanical strength slightly increases in this temperature range, although it has a sudden drop at 420 °C. Beyond the dehydroxylation range, above 650 °C, both Young's modulus and mechanical strength increase. Above 950 °C, a sharp increase of Young's modulus is caused by the solid-state sintering and the new structure created by the high-temperature reactions in metakaolinite.

  18. Anodizing And Sealing Aluminum In Nonchromated Solutions

    Science.gov (United States)

    Emmons, John R.; Kallenborn, Kelli J.

    1995-01-01

    Improved process for anodizing and sealing aluminum involves use of 5 volume percent sulfuric acid in water as anodizing solution, and 1.5 to 2.0 volume percent nickel acetate in water as sealing solution. Replaces process in which sulfuric acid used at concentrations of 10 to 20 percent. Improved process yields thinner coats offering resistance to corrosion, fatigue life, and alloy-to-alloy consistency equal to or superior to those of anodized coats produced with chromated solutions.

  19. Development of a Novel Non-Consumable Anode for Electrowinning Primary Aluminum

    Energy Technology Data Exchange (ETDEWEB)

    Robert A. Rapp; Y. Zhang

    2003-12-04

    The principal goal of the project was to determine through theoretical considerations and from chemical and electrochemical laboratory studies the technical and economic feasibility for the substitution and retrofitting of an SOFC-type anode for today's carbon anode in a cell for electrowinning primary Al. However, solubility measurements showed that no value of cryolite ratio can exist where the solubilities of the solid electrolyte components (zirconia and especially yttria) would be small relative to the alumina solubility. Therefore, the utilization of the proposed SOFC-type anode cannot be realized for any cell involving a cryolite-base solvent. However, the project suggested that the SOFC-type anode scheme might be successful if the solvent/electrolyte for electrowinning Al could be changed to a fused sulfate melt. During the solubility experiments, electrochemical probes were developed, and a bath characterization was defined, to measure quantitatively the acid-base character of cryolite melts. The measured acid-base behavior was then used to correlate the alumina solubility in cryolite over a wide range of cryolite ratio at 1300K. A mathematical modeling of the alumina solubility as a function of basicity identified three solutes of Al{sub 2}O{sub 3} in cryolite-base melts: Na{sub 2}Al{sub 2}OF{sub 6}, Na{sub 2}Al{sub 2}O{sub 2}F{sub 4}, and Na{sub 4}Al{sub 2}O{sub 2}F{sub 6} as acidic, neutral and basic solutes, respectively. For the first time, the stereochemistry (geometries) of these complex solutes was clarified. For the non-oxygen containing Al-F complex anions, Na{sub 3}AlF{sub 6} and NaAlF{sub 4} were also considered as solutes, and some NaF (but no AlF{sub 3}) could remain in the melts. The previously suggested solute Na{sub 2}AlF{sub 5} was found to be unstable. The strong complexing in the cryolite/alumina system means that the bath is highly buffered so that a significant shift in basicity is not possible and therefore the alumina

  20. Metrology on phase-shift masks

    Science.gov (United States)

    Roeth, Klaus-Dieter; Maurer, Wilhelm; Blaesing-Bangert, Carola

    1992-06-01

    In the evaluation of new manufacturing processes, metrology is a key function, beginning with the first step of process development through the final step of everyday mass production at the fabrication floor level. RIM-type phase shift masks are expected to be the first application of phase shift masks in high volume production, since they provide improved lithography process capability at the expense of only moderate complexity in their manufacturing. Measurements of critical dimension (CD) and pattern position (overlay) on experimental rim-type and chromeless phase shift masks are reported. Pattern placement (registration) was measured using the Leitz LMS 2000. The overall design and important components were already described. The pattern placement of the RIM type phase shift structures on the photomask described above was determined within a tolerance of 25 nm (3s); nominal accuracy was within 45 nm (3s). On the chromeless phase shift mask the measurement results were easily obtained using a wafer intensity algorithm available with the system. The measurement uncertainties were less than 25 nm and 50 nm for precision and nominal accuracy respectively. The measurement results from the Leitz CD 200 using transmitted light were: a CD- distribution of 135 nm (3s) on a typical 6 micrometers structure all over the mask; the 0.9 micrometers RIM structure had a distribution of 43 nm (3s). Typical long term precision performance values for the CD 200 on both chrome and phase shift structures have been less than 15 nm.