WorldWideScience

Sample records for anl zero power research reactor-6

  1. Simulation of IST Turbomachinery Power-Neutral Tests with the ANL Plant Dynamics Code

    Energy Technology Data Exchange (ETDEWEB)

    Moisseytsev, A. [Argonne National Lab. (ANL), Argonne, IL (United States); Sienicki, J. J. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-12-13

    The validation of the Plant Dynamics Code (PDC) developed at Argonne National Laboratory (ANL) for the steady-state and transient analysis of supercritical carbon dioxide (sCO2) systems has been continued with new test data from the Naval Nuclear Laboratory (operated by Bechtel Marine Propulsion Corporation) Integrated System Test (IST). Although data from three runs were provided to ANL, only two of the data sets were analyzed and described in this report. The common feature of these tests is the power-neutral operation of the turbine-compressor shaft, where no external power through the alternator was provided during the tests. Instead, the shaft speed was allowed to change dictated by the power balance between the turbine, the compressor, and the power losses in the shaft. The new test data turned out to be important for code validation for several reasons. First, the power-neutral operation of the shaft allows validation of the shaft dynamics equations in asynchronous mode, when the shaft is disconnected from the grid. Second, the shaft speed control with the compressor recirculation (CR) valve not only allows for testing the code control logic itself, but it also serves as a good test for validation of both the compressor surge control and the turbine bypass control actions, since the effect of the CR action on the loop conditions is similar for both of these controls. Third, the varying compressor-inlet temperature change test allows validation of the transient response of the precooler, a shell-and-tube heat exchanger. The first transient simulation of the compressor-inlet temperature variation Test 64661 showed a much slower calculated response of the precooler in the calculations than the test data. Further investigation revealed an error in calculating the heat exchanger tube mass for the PDC dynamic equations that resulted in a slower change in the tube wall temperature than measured. The transient calculations for both tests were done in two steps. The

  2. A zero-power radio receiver.

    Energy Technology Data Exchange (ETDEWEB)

    Brocato, Robert Wesley

    2004-09-01

    This report describes both a general methodology and some specific examples of passive radio receivers. A passive radio receiver uses no direct electrical power but makes sole use of the power available in the radio spectrum. These radio receivers are suitable as low data-rate receivers or passive alerting devices for standard, high power radio receivers. Some zero-power radio architectures exhibit significant improvements in range with the addition of very low power amplifiers or signal processing electronics. These ultra-low power radios are also discussed and compared to the purely zero-power approaches.

  3. ZERO EMISSION POWER GENERATION TECHNOLOGY DEVELOPMENT

    Energy Technology Data Exchange (ETDEWEB)

    Ronald Bischoff; Stephen Doyle

    2005-01-20

    Clean Energy Systems (CES) was previously funded by DOE's ''Vision 21'' program. This program provided a proof-of-concept demonstration that CES' novel gas generator (combustor) enabled production of electrical power from fossil fuels without pollution. CES has used current DOE funding for additional design study exercises which established the utility of the CES-cycle for retrofitting existing power plants for zero-emission operations and for incorporation in zero-emission, ''green field'' power plant concepts. DOE funding also helped define the suitability of existing steam turbine designs for use in the CES-cycle and explored the use of aero-derivative turbines for advanced power plant designs. This work is of interest to the California Energy Commission (CEC) and the Norwegian Ministry of Petroleum & Energy. California's air quality districts have significant non-attainment areas in which CES technology can help. CEC is currently funding a CES-cycle technology demonstration near Bakersfield, CA. The Norwegian government is supporting conceptual studies for a proposed 40 MW zero-emission power plant in Stavager, Norway which would use the CES-cycle. The latter project is called Zero-Emission Norwegian Gas (ZENG). In summary, current engineering studies: (1) supported engineering design of plant subsystems applicable for use with CES-cycle zero-emission power plants, and (2) documented the suitability and availability of steam turbines for use in CES-cycle power plants, with particular relevance to the Norwegian ZENG Project.

  4. Designing a zero emissions power switch locomotive

    Energy Technology Data Exchange (ETDEWEB)

    Shapiro, J.; Hines, J. [National Instruments, Austin, TX (United States)

    2009-07-01

    In addition to providing electric power and drinking water in manned spacecraft, fuel cell power plants have provided safe, clean electric power to hospitals, universities and other facilities since the early 1990s. This paper described a zero emissions hydrogen and battery-powered hybrid switching locomotive designed for use in rail, port and military base applications. Designed in partnership with a consortium, the prototype hybrid switching locomotive is comprised of a number of proven commercial technologies and includes a control system developed by National Instruments. New applications for hydrogen fuel cell use in industrial vehicles were also discussed. The new design was scheduled for field testing at the end of 2008.

  5. ZERO SET OF SOBOLEV FUNCTIONS WITH NEGATIVE POWER OF INTEGRABILITY

    Institute of Scientific and Technical Information of China (English)

    姜惠强; 林芳华

    2004-01-01

    Here the authors are interested in the zero set of Sobolev functions and functions of bounded variation with negative power of integrability. The main result is a general Hausdorff dimension estimate on the size of zero set. The research is motivated by the model on van der waal force driven thin film, which is a singular elliptic equation.After obtaining some basic regularity result, the authors get an estimate on the size of singular set; such set corresponds to the thin film rupture set in the thin film model.

  6. Research Toward Zero Energy Homes

    Energy Technology Data Exchange (ETDEWEB)

    Robert Hammon

    2010-12-31

    This final report was compiled from the detailed annual reports that were submitted for efforts in 2008 and 2009, and from individual task reports from 2010. Reports, case studies, and presentations derived from this work are available through the Building America website. The BIRA team is led by ConSol, a leading provider of energy solutions for builders since 1983. In partnership with over fifty builders, developers, architects, manufactures, researchers, utilities, and agencies, research work was performed in California, Colorado, Utah, New Mexico, Washington, Oregon, and Hawaii and five (5) climate regions (Hot-Dry, Marine, Hot-Humid, Cold, and Hot/Mixed Dry). In addition to research work, the team provided technical assistance to our partners whose interests span the entire building process. During the three year budget period, the BIRA team performed analyses of several emerging technologies, prototype homes, and high performance communities through detailed computer simulations and extensive field monitoring to meet the required climate joule milestone targets.

  7. A User Guide to PARET/ANL

    Energy Technology Data Exchange (ETDEWEB)

    Olson, A. P. [Argonne National Lab. (ANL), Argonne, IL (United States); Dionne, B. [Argonne National Lab. (ANL), Argonne, IL (United States); Marin-Lafleche, A. [Argonne National Lab. (ANL), Argonne, IL (United States); Kalimullah, M. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2015-01-01

    PARET was originally created in 1969 at what is now Idaho National Laboratory (INL), to analyze reactivity insertion events in research and test reactor cores cooled by light or heavy water, with fuel composed of either plates or pins. The use of PARET is also appropriate for fuel assemblies with curved fuel plates when their radii of curvatures are large with respect to the fuel plate thickness. The PARET/ANL version of the code has been developed at Argonne National Laboratory (ANL) under the sponsorship of the U.S. Department of Energy/NNSA, and has been used by the Reactor Conversion Program to determine the expected transient behavior of a large number of reactors. PARET/ANL models the various fueled regions of a reactor core as channels. Each of these channels consists of a single flat fuel plate/pin (including cladding and, optionally, a gap) with water coolant on each side. In slab geometry the coolant channels for a given fuel plate are of identical dimensions (mirror symmetry), but they can be of different thickness in each channel. There can be many channels, but each channel is independent and coupled only through reactivity feedback effects to the whole core. The time-dependent differential equations that represent the system are replaced by an equivalent set of finite-difference equations in space and time, which are integrated numerically. PARET/ANL uses fundamentally the same numerical scheme as RELAP5 for the time-integration of the point-kinetics equations. The one-dimensional thermal-hydraulic model includes temperature-dependent thermal properties of the solid materials, such as heat capacity and thermal conductivity, as well as the transient heat production and heat transfer from the fuel meat to the coolant. Temperature- and pressure-dependent thermal properties of the coolant such as enthalpy, density, thermal conductivity, and viscosity are also used in determining parameters such as friction factors and heat transfer coefficients. The code

  8. Power Challenges of Large Scale Research Infrastructures: the Square Kilometer Array and Solar Energy Integration; Towards a zero-carbon footprint next generation telescope

    CERN Document Server

    Barbosa, Domingos; Ruiz, Valeriano; Silva, Manuel; Verdes-Montenegro, Lourdes; Santander-Vela, Juande; Maia, Dalmiro; Antón, Sonia; van Ardenne, Arnold; Vetter, Matthias; Kramer, Michael; Keller, Reinhard; Pereira, Nuno; Silva, Vitor

    2012-01-01

    The Square Kilometer Array (SKA) will be the largest Global science project of the next two decades. It will encompass a sensor network dedicated to radioastronomy, covering two continents. It will be constructed in remote areas of South Africa and Australia, spreading over 3000Km, in high solar irradiance latitudes. Solar Power supply is therefore an option to power supply the SKA and contribute to a zero carbon footprint next generation telescope. Here we outline the major characteristics of the SKA and some innovation approaches on thermal solar energy Integration with SKA prototypes.

  9. Topology Zero: Advancing Theory and Experimentation for Power Electronics Education

    Science.gov (United States)

    Luchino, Federico

    For decades, power electronics education has been based on the fundamentals of three basic topologies: buck, boost, and buck-boost. This thesis presents the analytical framework for the Topology Zero, a general circuit topology that integrates the basic topologies and provides significant insight into the behaviour of converters. As demonstrated, many topologies are just particular cases of the Topology Zero, an important contribution towards the understanding, integration, and conceptualization of topologies. The investigation includes steady-state, small-signal, and frequency response analysis. The Topology Zero is physically implemented as an educational system. Experimental results are presented to show control applications and power losses analysis using the educational system. The steady-state and dynamic analyses of the Topology Zero provide profuse proof of its suitability as an integrative topology, and of its ability to be indirectly controlled. As well, the implementation of the Topology Zero within an experimentation system is explained and application examples are provided.

  10. Anlægsteknik 2

    DEFF Research Database (Denmark)

    Hermed foreligger en ny udgave af Anlægsteknik 2, hvor der er en del ændringer i forhold til 3. udgave. Dette skyldes at fagområdet Anlægsteknik er under konstant udvikling, og nye relevante emner derfor er medtaget i denne udgave samt at andre forældede emner er fjernet. Anlægsteknik 2 har...

  11. Topology zero: advancing theory and experimentation for power electronics education

    OpenAIRE

    Luchino, Federico

    2012-01-01

    For decades, power electronics education has been based on the fundamentals of three basic topologies: buck, boost, and buck-boost. This thesis presents the analytical framework for the Topology Zero, a general circuit topology that integrates the basic topologies and provides significant insight into the behaviour of converters. As demonstrated, many topologies are just particular cases of the Topology Zero, an important contribution towards the understanding, integration, and conceptualizat...

  12. The Swedish Zero Power Reactor R0

    Energy Technology Data Exchange (ETDEWEB)

    Landergaard, Olof; Cavallin, Kaj; Jonsson, Georg

    1961-05-15

    The reactor R0 is a critical facility built for heavy water and natural uranium or fuel of low enrichment,, The first criticality was achieved September 25, 1959. During a first period of more than two years the R0 will be operated as a bare reactor in order to simplify interpretation of results. The reactor tank is 3. 2 m high and 2. 25 m in diameter. The fuel suspension system is quite flexible in order to facilitate fuel exchange and lattice variations. The temperature of the water can be varied between about 10 and 90 C by means of a heater and a cooler placed in the external circulating system. The instrumentation of the reactor has to meet the safety requirements not only during operation but also during rearrangements of the core in the shut-down state. Therefore, the shut-down state is always defined by a certain low 'safe' moderator level in the reactor tank. A number of safety rods are normally kept above the moderator ready for action. For manual or automatic control of the reactor power a specially designed piston pump is needed, by which the moderator level is varied. The pump speed is controlled from the reactor power error by means of a Ward-Leonard system. Moderator level measurement is made by means of a water gauge with an accuracy of {+-} 0. 1 mm.

  13. Magnet powering with zero downtime - a dream?

    CERN Document Server

    Zerlauth, Markus

    2012-01-01

    Despite a number of improvements already applied in the course of the year, the magnet powering system of the LHC still accounts for around 50% of the premature beam dumps. This number might even further increase when moving to higher beam energies in the next years. With mitigations of radiation effects and the prospects for beam induced magnet quenches being discussed elsewhere, we aim at identifying possible mid- and long-term improvements within the various equipment systems to further reduce the number of equipment failures leading to a loss of the particle beams. Amongst others, this includes the sensitivity of equipment to external causes such as electromagnetic perturbations or perturbations on the electrical network. To conclude, the gain of the identified mitigations will have to be balanced against the potential impact on schedule and cost.

  14. Zero Tolerance: Advantages and Disadvantages. Research Brief

    Science.gov (United States)

    Walker, Karen

    2009-01-01

    What are the positives and negatives of zero tolerance? What should be considered when examining a school's program? Although there are no definitive definitions of zero tolerance, two commonly used ones are as follows: "Zero tolerance means that a school will automatically and severely punish a student for a variety of infractions" (American Bar…

  15. The case for research into the zero accident vision

    NARCIS (Netherlands)

    Zwetsloot, G.I.J.M.; Aaltonen, M.; Wybo,J.L.; Saari, J.; Kines, P.; Beeck, R. op de

    2013-01-01

    This discussion paper is written out of a concern. We noticed that many companies with a good safety reputation have adopted a zero accident vision, yet there is very little scientific research in this field. The zero accident vision addresses the accidents causing deaths and severe injuries among c

  16. Daxing anling Forestry Group Co.

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Located on the Daxing'anling forest region of China's frontier, the Daxing'anling Forestry Group Co. is one of the 500 national large size enterprise groups with a total management area of 8.225 million ha. There are 10forestry bureaus under its jurisdiction, 93 000 in-service staff and a population of 358 000. The net value of fixed asset is 3. 58 billion yuan, Accumulative total output of timber has amounted to 110 million m3 during the past 38 years. Its profits and tax turned over to the State has t...

  17. Zero loss magnetic metamaterials using powered active unit cells.

    Science.gov (United States)

    Yuan, Yu; Popa, Bogdan-Ioan; Cummer, Steven A

    2009-08-31

    We report the design and experimental measurement of a powered active magnetic metamaterial with tunable permeability. The unit cell is based on the combination of an embedded radiofrequency amplifier and a tunable phase shifter, which together control the response of the medium. The measurements show that a negative permeability metamaterial with zero loss or even gain can be achieved through an array of such metamaterial cells. This kind of active metamaterial can find use in applications that are performance limited due to material losses.

  18. Thermodynamic analysis of the advanced zero emission power plant

    Directory of Open Access Journals (Sweden)

    Kotowicz Janusz

    2016-03-01

    Full Text Available The paper presents the structure and parameters of advanced zero emission power plant (AZEP. This concept is based on the replacement of the combustion chamber in a gas turbine by the membrane reactor. The reactor has three basic functions: (i oxygen separation from the air through the membrane, (ii combustion of the fuel, and (iii heat transfer to heat the oxygen-depleted air. In the discussed unit hot depleted air is expanded in a turbine and further feeds a bottoming steam cycle (BSC through the main heat recovery steam generator (HRSG. Flue gas leaving the membrane reactor feeds the second HRSG. The flue gas consist mainly of CO2 and water vapor, thus, CO2 separation involves only the flue gas drying. Results of the thermodynamic analysis of described power plant are presented.

  19. Thermodynamic analysis of the advanced zero emission power plant

    Science.gov (United States)

    Kotowicz, Janusz; Job, Marcin

    2016-03-01

    The paper presents the structure and parameters of advanced zero emission power plant (AZEP). This concept is based on the replacement of the combustion chamber in a gas turbine by the membrane reactor. The reactor has three basic functions: (i) oxygen separation from the air through the membrane, (ii) combustion of the fuel, and (iii) heat transfer to heat the oxygen-depleted air. In the discussed unit hot depleted air is expanded in a turbine and further feeds a bottoming steam cycle (BSC) through the main heat recovery steam generator (HRSG). Flue gas leaving the membrane reactor feeds the second HRSG. The flue gas consist mainly of CO2 and water vapor, thus, CO2 separation involves only the flue gas drying. Results of the thermodynamic analysis of described power plant are presented.

  20. Recent activities at the zero-power teaching reactor CROCUS

    Energy Technology Data Exchange (ETDEWEB)

    Girardin, G.; Chawla, R., E-mail: gaetan.girardin@epfl.ch [Swiss Polytechnical School of Lausanne, Lausanne (Switzerland)

    2011-07-01

    CROCUS is a zero-power critical facility used mainly for educational purposes at the Swiss Federal Institute of Technology (EPFL) in Lausanne, Switzerland. It is a low-enriched-uranium fuelled, light-water moderated reactor, with the fission power limited to 100 W. The presentation will discuss the crucial role of CROCUS in teaching -- both as framework for reactor practicals offered to physics students at EPFL and as key educational tool in the recently established Swiss Master of Science in Nuclear Engineering. Regular development work is needed for the various instruments and components associated with the facility. As illustration, the recently completed refurbishment of the control rod system and the related calibration experiments will also be discussed.

  1. Zeta function zeros, powers of primes, and quantum chaos.

    Science.gov (United States)

    Sakhr, Jamal; Bhaduri, Rajat K; van Zyl, Brandon P

    2003-08-01

    We present a numerical study of Riemann's formula for the oscillating part of the density of the primes and their integer powers. The formula consists of an infinite series of oscillatory terms, one for each zero of the zeta function on the critical line, and was derived by Riemann in his paper on primes, assuming the Riemann hypothesis. We show that high-resolution spectral lines can be generated by the truncated series at all integer powers of primes and demonstrate explicitly that the relative line intensities are correct. We then derive a Gaussian sum rule for Riemann's formula. This is used to analyze the numerical convergence of the truncated series. The connections to quantum chaos and semiclassical physics are discussed.

  2. Energistyring med CTS-anlæg

    DEFF Research Database (Denmark)

    Reinhold, Claus

    Rapporten gennemgår mulighederne for energistyring ved hjælp af anlæg for central tilstandskontrol og styring - de såkaldte CTS-anlæg. Der beskrives grundprincipper og typiske systemopbygninger, samt de praktiske erfaringer fra et stort engelsk forskningsprojekt og fra fire CTS-anlæg i Danmark....

  3. Neutron dose estimation in a zero power nuclear reactor

    Science.gov (United States)

    Triviño, S.; Vedelago, J.; Cantargi, F.; Keil, W.; Figueroa, R.; Mattea, F.; Chautemps, A.; Santibañez, M.; Valente, M.

    2016-10-01

    This work presents the characterization and contribution of neutron and gamma components to the absorbed dose in a zero power nuclear reactor. A dosimetric method based on Fricke gel was implemented to evaluate the separation between dose components in the mixed field. The validation of this proposed method was performed by means of direct measurements of neutron flux in different positions using Au and Mg-Ni activation foils. Monte Carlo simulations were conversely performed using the MCNP main code with a dedicated subroutine to incorporate the exact complete geometry of the nuclear reactor facility. Once nuclear fuel elements were defined, the simulations computed the different contributions to the absorbed dose in specific positions inside the core. Thermal/epithermal contributions of absorbed dose were assessed by means of Fricke gel dosimetry using different isotopic compositions aimed at modifying the sensitivity of the dosimeter for specific dose components. Clear distinctions between gamma and neutron capture dose were obtained. Both Monte Carlo simulations and experimental results provided reliable estimations about neutron flux rate as well as dose rate during the reactor operation. Simulations and experimental results are in good agreement in every positions measured and simulated in the core.

  4. Crystal Power: Piezo Coupling to the Quantum Zero Point

    CERN Document Server

    November, Laurence J

    2011-01-01

    We consider electro-optical constructions in which the Casimir force is modulated in opposition to piezo-crystal elasticity, as in a stack of alternating tunably conductive and piezo layers. Adjacent tunably conducting layers tuned to conduct, attract by the Casimir force compressing the intermediate piezo, but when subsequently detuned to insulate, sandwiched piezo layers expand elastically to restore their original dimension. In each cycle some electrical energy is made available from the quantum zero point (zp). We estimate that the maximum power that could be derived at semiconductor THz modulation rates is megawatts/cm3. Similarly a permittivity wave generated by a THz acoustic wave in a single crystal by the acousto-optic effect produces multiple coherent Casimir wave mode overtones and a bulk mode. We model the Casimir effect in a sinusoidally graded medium finding it to be very enhanced over what is found in a multilayer stack for the equivalent permittivity contrast, and more slowly decreasing with s...

  5. Electrolysers as a load management mechanism for power systems with wind power and zero-carbon thermal power plant

    Energy Technology Data Exchange (ETDEWEB)

    Troncoso, E. [School of Industrial Engineering, Universidad Las Palmas de Gran Canaria (Spain); Newborough, M. [ITM Power Research Ltd., Mill House, Royston Road, Wendens Ambo, Saffron Walden CB11 4JX (United Kingdom)

    2010-01-15

    For an isolated power system the deployment of a large stock of electrolysers is investigated as a means for increasing the penetrations of wind power plant and zero-carbon thermal power plant. Consideration is given to the sizing and utilization of an electrolyser stock for three electrolyser implementation cases and three operational strategies, installed capacity ranges of 20-100% for wind power and 10-35% for zero-carbon thermal power plant (as proportions of the power system's maximum electrical demand) were investigated. Relative to wind-hydrogen alone, hydrogen yields are substantially increased especially on low-wind days. The average load placed on fossil-fuelled power plant is substantially decreased (while achieving a virtually flat load profile) and the carbon intensity of electricity can be reduced to values of <0.1 kg CO{sub 2}/kWh{sub e}. The trade-offs between the carbon intensity of the electricity delivered, the carbon intensity of the hydrogen produced and the daily hydrogen yield are explored. For example (on the variable wind day for Strategy C with respective wind power and zero-carbon thermal power penetrations of 100% and 35%), if the carbon intensity of hydrogen is relaxed from 0 to 3 kg CO{sub 2}/kg H{sub 2}, the hydrogen yield can be increased from 435 tonnes to 1115 tonnes (which is the energy equivalent of 120% of consumer demand for electricity on that day). The findings suggest that the deployment of electrolysers on both the supply and demand-side of the power system can contribute nationally-significant amounts of zero or low-carbon hydrogen without exceeding the power system's current maximum system demand. (author)

  6. 低压智能电容器自适应过零投切技术的研究%Research on Adaptive Zero-Crossing Switching Technology of Low Voltage Intelligent Power Capacitor

    Institute of Scientific and Technical Information of China (English)

    王砼; 陈丽安; 刘涛

    2014-01-01

    提出了一种用于智能电容器的基于电压零点闭环控制的自适应过零同步投切技术。采用模拟电路检测电压零点以及反馈投切时刻,改进磁保持继电器驱动电路,简化采样计算环节,提高了磁保持继电器动作一致性和自适应控制的准确性、稳定性。试验结果表明,该技术具有稳定、可靠的自适应控制效果及对低压电容器投入涌流的限制作用。%An adaptive zero-crossing switching technology for intelligent power capacitor based on closed loop control of zero voltage was presented.Analog circuits were applied for catching zero point of voltage and feeding back switching time.The drive circuits of magnetic latching relay were improved so that its action time has greater consistency.By simplifying the process of sampling and calculating,the stability and accuracy of adaptive control have been improved.The experimental results show that this technology has a stable and reliable effect on adaptive control as well as the result of limiting the inrush current of switching power capacitor.

  7. Zero-emission fuel-fired power plants with ion transport membrane

    NARCIS (Netherlands)

    Yantovski, E.; Gorski, J.; Smyth, B.; Elshof, ten J.

    2004-01-01

    Firstly, some points in relation to the history of zero-emissions power cycles are highlighted. Amongst the many schemes, only one which deals with the combustion of a fuel in “artificial air” (i.e. a mixture of oxygen and re-circulated carbon dioxide), is selected. This paper describes the zero em

  8. Research in electric power

    CERN Document Server

    Sporn, Philip

    2013-01-01

    Research in Electric Power comprises the lectures presented in the Cornell University Lecture in 1965, which focuses on the research and development of electric energy or technology. The lectures compiled in this book are divided into three chapters. Chapter I traces the dramatic and exciting history of growth of the electric power industry and important contribution of a series of great technological developments. The second chapter examines in great detail the problems demanding research in the main areas of planning, design, and construction of the physical facilities; in successfully and e

  9. 基于相关分析的暂态零模电流与功率故障定位方法比较%Comparative Research on Fault Location by Transient Zero-Module Current and Transient Zero-Module Power Based on Correlation Analysis

    Institute of Scientific and Technical Information of China (English)

    田书; 王晓卫; 王娟娟

    2011-01-01

    在分析小电流接地系统单相接地故障暂态零模电流与功率特性的基础上,利用故障点同侧2点暂态信息量相似度高、相关系数接近于1,而故障点两侧2点相似度低、相关系数小这一特点,对电流法和功率法在不同电压初相角与接地电阻时的相关系数进行了对比,分析得出,在阀值的选择上,电流法较功率法灵活且裕度大,抗干扰能力强:而功率法在线路末端高阻接地时,信号获取较为容易.另外,提出相关系数比例因子的概念,用于对2种方法的相关系数值进行综合性能评价,得出了各自方法的最佳工作性能区间.%On the basis of analyzing characteristics of transient zero-module current and power during single-phase earth fault occurred in small current neutral grounding system,by use of the feature that the transient information from two detection points located at the same side of fault point possesses high similarity and the value of correlation coefficient is close to 1 and the transient information from two detection points located at the opposite sides of fault point possesses low similarity and the value of correlation coefficient is small, the correlation coefficients obtained by transient zero-module power method and Transient zero-module current method respectively under different initial phase angles and grounding resistances are compared. Analysis results show that in the selection of threshold value, the current method is more flexible and has larger margin than power method, so current method possesses better anti-interference performance;however, as for power method it is more easily to acquire signal while the transmission line is grounded via high resistance at its end terminal. Besides, in order to comprehensively evaluate the performances of the two methods,a concept of scale factor of correlation coefficient is proposed,and the ranges of the two methods, where their working performances can be fully brought into

  10. Hybrid zero-voltage switching (ZVS) control for power inverters

    Science.gov (United States)

    Amirahmadi, Ahmadreza; Hu, Haibing; Batarseh, Issa

    2016-11-01

    A power inverter combination includes a half-bridge power inverter including first and second semiconductor power switches receiving input power having an intermediate node therebetween providing an inductor current through an inductor. A controller includes input comparison circuitry receiving the inductor current having outputs coupled to first inputs of pulse width modulation (PWM) generation circuitry, and a predictive control block having an output coupled to second inputs of the PWM generation circuitry. The predictive control block is coupled to receive a measure of Vin and an output voltage at a grid connection point. A memory stores a current control algorithm configured for resetting a PWM period for a switching signal applied to control nodes of the first and second power switch whenever the inductor current reaches a predetermined upper limit or a predetermined lower limit.

  11. Possible optimal configurations for the ZECOMIX high efficiency zero emission hydrogen and power plant

    Energy Technology Data Exchange (ETDEWEB)

    Calabro, A.; Deiana, P.; Florini, P.; Girardi, G.; Stendardo, S. [ENEA, Rome (Italy). Italian Agency for New Technology Energy & Environment

    2008-06-15

    Coal use for electricity generation will continue growing in importance. In the present work the optimization of a high efficiency and zero emissions coal-fired plant, which produces both hydrogen and electricity, has been developed. The majority of this paper concerns an integration of gasification unit, which is characterized by coal hydrogasification and carbon dioxide (CO{sub 2}) separation, with a power island, where a high-hydrogen content syngas is burnt with pure oxygen stream. Another issue is the high temperature CO{sub 2} desorption. Because of the elevated temperature heat supply, the regeneration process affects the overall performance of ZECOMIX plant. An advanced steam cycle characterized by a medium pressure steam compressor and expander has been considered for power generation. A preliminary study of different components leads to analyze possible routes for optimization of the whole plant. The plant equipped with a CO{sub 2} capture unit could reach efficiency close to 50%. The simulations of a thermodynamic model were carried out using the software ChemCAD. This study is a part of a larger research project, named ZECOMIX, led by ENEA (Italian Research Agency for New technologies, Energy and Environment), other partners being ANSALDO and different Italian Universities. It is aimed at analyzing an integrated hydrogen and power production plant.

  12. Zero Power Levitation Control of Hybrid Electro-Magnetic Levitation System by Load Observer

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Youn Hyun; Lee, Ju [Hanyang University, Seoul (Korea)

    2001-06-01

    This paper introduces the scheme that improve the control performance of electromagnetic levitation system with zero power controller. Magnetic levitation is used widely, but the electromagnetic force has nonlinear characteristics because it is proportioned to a square of the magnetic flux density and it is in inverse proportion to a square of the air gap. So, it is complicate and difficult to control the electromagnetic force. Besides, it is more difficult to control if the equivalent gap is unknown in case of zero power control. Therefore, this paper proposed the hybrid electro-magnetic levitation control method in which the variable load is estimated by using a load observer and its system is controlled at a new zero power equilibrium air gap position. Also it is confirmed that the proposed control method improve the control performance through simulation and experiment. (author). 10 refs., 17 figs., 1 tab.

  13. A comparison between Zecomix High Efficiency Zero Emission Plant and modern Hydrogen and Power IGCC Plants

    Energy Technology Data Exchange (ETDEWEB)

    Deiana, P.; Calabro, A.; Fiorini, P.; Stendardo, S.; Girardi, G.

    2005-07-01

    The paper reports the analysis and the comparison of two different plant concepts in the field of high efficiency and zero emissions hydrogen and power production plant. The study has been made as a part of a larger research project, named Zecomix, leaded by ENEA (Italian Research Agency for New Technologies, Energy and Environment), and aimed at studying an integrated process that produces both hydrogen and electricity from coal. A thermodynamic model of the two different plants has been set using the industrial software ChemCAD. The Zecomix plant is based on coal hydrogasification and simultaneous steam reforming and carbon dioxide sequestration. Other crucial characteristics involve high temperature sorbent regeneration. The combustion occurs with pure oxygen and high temperature steam evolves in a nonconventional advanced gas-steam turbine cycle. The considered IGCC plant is capable of producing hydrogen and power adopting current technology solutions. The plant configuration includes a pressurized oxygen blown entrained flow gasifier, syngas cleanup and decarbonization based on high pressure physical absorption, the adoption of class H gas turbine and three pressure level recovery boiler. Moreover a pressure swing adsorption unit has been considered for further hydrogen purification. The comparative analysis, based on the same coal input, underlines the differences between the two plants in terms of efficiency and performance of the single component. Moreover a simple environmental impact analysis has been considered to compare specific CO2 emissions of each alternative. (Author)

  14. Sums of the Powers of the Zeros of the Mittag-Leffler Function

    Science.gov (United States)

    Hanneken, John W.; Puzio, Raymond S.; Narahari Achar, B. N.

    2004-03-01

    The Mittag-Leffler function, which is a generalization of the exponential function, occurs naturally in the solution of dynamic problems involving fractional calculus. For example see the book Fractional Differential Equations by Podlubny, or for a specific application see the problem of the fractional oscillator by Achar et. al. Physica A297 (2001) 361 and A309 (2002) 275. The zeros of the Mittag-Leffler function play a significant role in the dynamic solutions. However, very little is known about these zeros. A summary of the available information about the zeros of Mittag-Leffler functions will be given and new results pertaining to the sums of the powers of the zeros will be presented.

  15. Gas separation membranes for zero-emission fossil power plants: MEM-BRAIN

    NARCIS (Netherlands)

    Czyperek, M.; Zapp, P.; Bouwmeester, H.J.M.; Modigell, M.; Ebert, K.; Voigt, I.; Meulenberg, W.A.; Singheiser, L.; Stöver, D.

    2010-01-01

    The objective of the “MEM-BRAIN” project is the development and integration of ceramic and polymeric gas separation membranes for zero-emission fossil power plants. This will be achieved using membranes with a high permeability and selectivity for either CO2, O2 or H2, for the three CO2 capture proc

  16. MEM-BRAIN gas separation membranes for zero-emission fossil power plants

    NARCIS (Netherlands)

    Czyperek, M.; Zapp, P.; Bouwmeester, H.J.M.; Modigell, M.; Peinemann, K.-V.; Voigt, I.; Meulenberg, W.A.; Singheiser, L.; Stöver, D.

    2009-01-01

    The aim of the MEM-BRAIN project is the development and integration of gas separation membranes for zero-emission fossil power plants. This will be achieved by selective membranes with high permeability for CO2, O2 or H2, so that high-purity CO2 is obtained in a readily condensable form. The project

  17. 大兴安岭废弃金矿樟子松人工林生长规律的研究1)%Research on Growth Law of Pinus sylvestris Plantation at Discarded Gold Mine in Daxing’anling

    Institute of Scientific and Technical Information of China (English)

    崔崧; 魏嵩; 王承义

    2012-01-01

      This research investigated the grow th indexes of Pinus sylvestris plantation in gold de-posit slash in Guliku on the Daxing ’anling Jiagedaqi Forestry Bureau ,and obtained the grow th law of Pinus sylvestris plantation planted in discarded gold mine .The conclusions were as fol-lows:Pinus sylvestris plantation’s height grow th was influenced by the environmental factors significantly ,annul growth present increasing year by year ;Pinus sylvestris plantation’s diame-ter grow th effected by environmental factors showed no obvious rule ;forest at the edge of Pinus sylvestris crown not grow well ;Pinus sylvestris plantation freeze injuried by monsoon climate was very obvious ,and the main wind at winter damaged the branches severely .%  通过对大兴安岭加格达奇林业局古利库经营所管区内金矿迹地樟子松人工林的生长指标进行了调查,明确了废弃金矿樟子松人工林的生长规律。结论如下:樟子松树高生长受环境因子的影响显著,年生长量呈现逐年递增的趋势;樟子松地径生长受环境因子影响未表现出明显规律;林缘处樟子松冠幅生长较差;樟子松人工林受季风性带来的冻害影响非常明显,冬季主风向一侧的枝条冻害严重。

  18. Wind power systems for zero net energy housing in the United States

    Energy Technology Data Exchange (ETDEWEB)

    Elkinton, Melissa R.; McGowan, Jon G.; Manwell, James F. [Renewable Energy Research Laboratory, Department of Mechanical and Industrial Engineering, University of Massachusetts, Amherst, MA 01003 (United States)

    2009-05-15

    This work investigates the feasibility of renewable energy housing development in the U.S. using wind power and solar thermal systems to attain zero net energy consumption. The over all objective was to determine how the wind power and solar thermal system designs and economics differ with various climates, wind and solar resources, energy prices, and state incentives, such as net-metering. Five U.S. cities, one in each of the five climate zones, were selected for this study based on their potential for wind power. A zero net energy housing design tool was developed in order to analyze and compare various system designs. The energy performance and economics of the designs were compared for various sizes of housing development, for seven turbine models, and selected heating systems. The results suggest that while there are some economical options for wind powered zero net energy housing developments, they are generally more expensive (except in the warmest climate zone) than housing with natural gas heating. In all of the cases, the economies of scale for large-scale wind turbines gave more of an economic advantage than net-metering programs gave small- and medium-scale wind turbines. (author)

  19. Analysis of gamma-ray dosimetry experiments in the zero power MINERVE facility

    Energy Technology Data Exchange (ETDEWEB)

    Amharrak, H.; Di Salvo, J.; Lyoussi, A.; Roche, A.; Masson-Fauchier, M.; Bosq, J. C. [CEA, DEN, DER, F-13108 Saint-Paul-lez-Durance (France); Carette, M. [Aix-Marseille Univ., LCP UMR 6264, 13397, Marseille (France)

    2011-07-01

    The objective of this study is to develop nuclear heating measurement methods in zero power experimental reactors. These developments contribute to the qualification of photonics calculation schemes for the assessment of gamma heating in the future Jules Horowitz Material Testing Reactor. This paper presents the analysis of thermoluminescent detector (TLD) experiments in the UO{sub 2} core of the MINERVE Research Reactor at the French Alternative Energies and Atomic Energy Commission center in Cadarache. The experimental sources of uncertainty in the gamma dose have been reduced by improving the measurement conditions and the repeatability of the calibration step for each individual TLD. The interpretation of these measurements needs to take into account the calculation of cavity correction factors related to calibration and irradiation configurations, as well as neutron correction calculations. These calculations are based on Monte Carlo simulations of neutron-gamma and gamma-electron transport coupled particles. The comparison between calculated and measured integral gamma-ray absorbed doses in the aluminum material surrounding the TLD shows that calculations slightly overestimate the measurement, with a calculated versus experimental ratio equal to 1.04 {+-} 5.7 % (k=2). (authors)

  20. An Innovative Test Platform for Hydrogen Production and Zero Emission Power Generation from Coal

    Energy Technology Data Exchange (ETDEWEB)

    Calabro A; Deiana P; Fiorini P; Stendardo S; Girardi G [ENEA - Italian Agency for New Technologies, Energy and Environment Energy and Plants Division - Via Anguillarese - 301 00060 S Maria di Galeria - Rome (Italy)

    2006-07-01

    The ZECOMIX project, conceived by ENEA in the framework of Italian National Hydrogen Project, is aimed at studying an integrated process that produces both hydrogen and electricity from coal, with zero emissions and very high efficiency. The key element is the integration of a gasification process, characterized by coal hydro-gasification technology and carbon dioxide sequestration, with the power island, where an oxy-combustion occurs. Many optimization analysis and simulations have been carried out demonstrating the possibility to achieve very high net efficiencies (higher than 50% LHV) and very low (quasi-zero) emissions. The project schedule consists of the design, already started, the construction and the operation of an experimental facility finalized to demonstrate the feasibility of the described reference process. The facility will be realized in the ENEA Research Center of Casaccia, near Rome. It consists of a very flexible plant, in which more components can be tested separately or connected together. The plant is provided with a 50 kg/h coal atmospheric fluid bed gasifier, a fluid bed decarbonator/calcinator reactor filled with calcium oxide pellets, a pressurized hydro-gasifier reactor characterized by a pressure variable from 30 to 100 bar, a 100 kWe micro-turbine test bench, with the combustor chamber modified because of de-carbonized syngas fuelling and finally an oxygen/hydrogen combustor test bench, for experimental activities about the definition of stability limits, operative conditions (dilution, temperature pattern, chemicals) and combustion control. Other auxiliary components are mixing station for hydrogen-based syngas production, and an ordinary steam generator. The first part of the research project is aimed at testing the single component, in particular the main preliminary design criteria adopted for hydro-gasification reactor and carbonator reactor are presented in this paper. The second part of the Project is focused on the integration

  1. Determination of thermal hydraulic data of GHARR-1 under reactivity insertion transients using the PARET/ANL code

    Energy Technology Data Exchange (ETDEWEB)

    Adoo, N.A., E-mail: nanakwame10@hotmail.com [School of Nuclear and Allied Sciences, University of Ghana, Legon, P.O. Box AE 1, Atomic, Accra (Ghana); Nyarko, B.J.B.; Akaho, E.H.K. [School of Nuclear and Allied Sciences, University of Ghana, Legon, P.O. Box AE 1, Atomic, Accra (Ghana); National Nuclear Research Institute, Ghana Atomic Energy Commission, P.O. Box LG 80, Accra (Ghana); Alhassan, E.; Agbodemegbe, V.Y.; Bansah, C.Y.; Della, R. [School of Nuclear and Allied Sciences, University of Ghana, Legon, P.O. Box AE 1, Atomic, Accra (Ghana)

    2011-12-15

    The PARET/ANL code has been adapted by the IAEA for testing transient behaviour in research reactors since it provides a coupled thermal hydrodynamic and point kinetics capability for estimating thermal hydraulic margins. A two-channel power peaking profile of the Ghana Research Reactor-1 (GHARR-1) has been developed for the PARET/ANL (Version 7.3; 2007) using the Monte Carlo N-Particle code (MCNP) to determine the thermal hydraulic data for reactivity insertion transients in the range of 2.0 Multiplication-Sign 10{sup -3} {Delta}k/k to 5.5 Multiplication-Sign 10{sup -3} {Delta}k/k. Peak clad and coolant temperatures ranged from 59.18 Degree-Sign C to 112.36 Degree-Sign C and 42.95 Degree-Sign C to 79.42 Degree-Sign C respectively. Calculated safety margins (DNBR) satisfied the MNSR thermal hydraulic design criteria for which no boiling occurs in the reactor core. The generated thermal hydraulic data demonstrated a high inherent safety feature of GHARR-1 for which the high negative reactivity feedback of the moderator limits power excursion and consequently the escalation of the clad temperature.

  2. Numerical study of high-power semiconductor lasers for operation at sub-zero temperatures

    Science.gov (United States)

    Hasler, K. H.; Frevert, C.; Crump, P.; Erbert, G.; Wenzel, H.

    2017-04-01

    We present results on the impact of the Al-content in the waveguide structure on the electro-optical characteristics of 9xx nm, GaAs-based high-power lasers operated at room (300 K) and at sub-zero (200 K) heat sink temperatures. Experimentally a strong improvement of conversion efficiency and output power has been found if the lasers are cooled down. Numerical simulations using a software tool which solves the thermo-dynamic based drift-diffusion equations are able to reproduce the experimental findings. The reasons for the improved performance at lower temperatures are the enhancement of the modal gain and the reduced accumulation of electrons in the p-confinement layers resulting in a reduction of the leakage current. The latter allows the realization of lasers with a reduced Al content having a smaller series resistance and thus further enlarged conversion efficiency at sub-zero temperatures.

  3. MEASUREMENT ERROR EFFECT ON THE POWER OF CONTROL CHART FOR ZERO-TRUNCATED POISSON DISTRIBUTION

    Directory of Open Access Journals (Sweden)

    Ashit Chakraborty

    2013-09-01

    Full Text Available Measurement error is the difference between the true value and the measured value of a quantity that exists in practice and may considerably affect the performance of control charts in some cases. Measurement error variability has uncertainty which can be from several sources. In this paper, we have studied the effect of these sources of variability on the power characteristics of control chart and obtained the values of average run length (ARL for zero-truncated Poisson distribution (ZTPD. Expression of the power of control chart for variable sample size under standardized normal variate for ZTPD is also derived.

  4. ANL analysis of ZPPR-13A

    Energy Technology Data Exchange (ETDEWEB)

    Collins, P.J.; Brumbach, S.B. [comps.

    1984-08-09

    The ZPPR-13 experiments provide basic physics data for radial heterogeneous LMFBR cores of approximately 700MWe size. Assemblies ZPPR-13A, ZPPR-13B and ZPPR-13C comprised the JUPITER-II cooperative program between the U.S. Department of Energy (US DOE) and PNC of Japan. The measurements were made between August 1982 and April 1984. The core designs and the measurements were planned jointly by the two parties with substantial input from U.S. industrial interests to ensure coverage of the design requirements. This report describes in detail the results of the Argonne National Laboratory (ANL) analyses of phase 13A.

  5. A user's guide to the PLTEMP/ANL code.

    Energy Technology Data Exchange (ETDEWEB)

    Kalimullah, M. (Nuclear Engineering Division)

    2011-07-05

    PLTEMP/ANL V4.1 is a FORTRAN program that obtains a steady-state flow and temperature solution for a nuclear reactor core, or for a single fuel assembly. It is based on an evolutionary sequence of ''PLTEMP'' codes in use at ANL for the past 20 years. Fueled and non-fueled regions are modeled. Each fuel assembly consists of one or more plates or tubes separated by coolant channels. The fuel plates may have one to five layers of different materials, each with heat generation. The width of a fuel plate may be divided into multiple longitudinal stripes, each with its own axial power shape. The temperature solution is effectively 2-dimensional. It begins with a one-dimensional solution across all coolant channels and fuel plates/tubes within a given fuel assembly, at the entrance to the assembly. The temperature solution is repeated for each axial node along the length of the fuel assembly. The geometry may be either slab or radial, corresponding to fuel assemblies made of a series of flat (or slightly curved) plates, or of nested tubes. A variety of thermal-hydraulic correlations are available with which to determine safety margins such as Onset-of-Nucleate boiling (ONB), departure from nucleate boiling (DNB), and onset of flow instability (FI). Coolant properties for either light or heavy water are obtained from FORTRAN functions rather than from tables. The code is intended for thermal-hydraulic analysis of research reactor performance in the sub-cooled boiling regime. Both turbulent and laminar flow regimes can be modeled. Options to calculate both forced flow and natural circulation are available. A general search capability is available (Appendix XII) to greatly reduce the reactor analyst's time.

  6. A User's Guide to the PLTEMP/ANL Code

    Energy Technology Data Exchange (ETDEWEB)

    Olson, Arne P. [Argonne National Lab. (ANL), Argonne, IL (United States); Kalimullah, M. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2015-07-07

    PLTEMP/ANL V4.2 is a FORTRAN program that obtains a steady-state flow and temperature solution for a nuclear reactor core, or for a single fuel assembly. It is based on an evolutionary sequence of ''PLTEMP'' codes in use at ANL for the past 20 years. Fueled and non-fueled regions are modeled. Each fuel assembly consists of one or more plates or tubes separated by coolant channels. The fuel plates may have one to five layers of different materials, each with heat generation. The width of a fuel plate may be divided into multiple longitudinal stripes, each with its own axial power shape. The temperature solution is effectively 2-dimensional. It begins with a one-dimensional solution across all coolant channels and fuel plates/tubes within a given fuel assembly, at the entrance to the assembly. The temperature solution is repeated for each axial node along the length of the fuel assembly. The geometry may be either slab or radial, corresponding to fuel assemblies made of a series of flat (or slightly curved) plates, or of nested tubes. A variety of thermal-hydraulic correlations are available with which to determine safety margins such as Onset-of- Nucleate boiling (ONB), departure from nucleate boiling (DNB), and onset of flow instability (FI). Coolant properties for either light or heavy water are obtained from FORTRAN functions rather than from tables. The code is intended for thermal-hydraulic analysis of research reactor performance in the sub-cooled boiling regime. Both turbulent and laminar flow regimes can be modeled. Options to calculate both forced flow and natural circulation are available. A general search capability is available (Appendix XII) to greatly reduce the reactor analyst’s time.

  7. Low-Drift Flow Sensor with Zero-Offset Thermopile-Based Power Feedback

    CERN Document Server

    Dijkstra, M; De Boer, Meint; Berenschot, J W; Wiegerink, Remco; Elwenspoek, M

    2008-01-01

    A thermal flow sensor has been realised consisting of freely-suspended silicon-rich silicon-nitride microchannels with an integrated Al/poly-Si++ thermopile in combination with up- and downstream Al heater resistors. The inherently zero offset of the thermopile is exploited in a feedback loop controlling the dissipated power in the heater resistors, eliminating inevitable influences of resistance drift and mismatch of the thin-film metal resistors. The control system cancels the flow-induced temperature difference across the thermopile by controlling a power difference between both heater resistors, thereby giving a measure for the flow rate. The flow sensor was characterised for power difference versus water flow rates up to 1.5 ul/min, being in good agreement with a thermal model of the sensor, and the correct low-drift operation of the temperature-balancing control system has been verified.

  8. Bringing Power to Planning Research

    DEFF Research Database (Denmark)

    Flyvbjerg, Bent

    of how the methodology he developed for power studies, called "phronetic planning research," may be employed in practice. Phronetic planning research follows the tradition of power studies running from Machiavelli and Nietzsche to Michel Foucault and Pierre Bourdieu. It focuses on four value......This article provides an answer to what has been called the biggest problem in theorizing and understanding planning, namely the ambivalence about power found among planning researchers, theorists, and students. The author narrates how he came to work with issues of power. He then gives an example......-rational questions: (1) Where are we going with planning? (2) Who gains and who loses, and by which mechanisms of power? (3) Is this development desirable? (4) What should be done? These questions are exemplified for a specific instance of Scandinavian urban planning. The author finds that the questions...

  9. Bringing Power to Planning Research

    DEFF Research Database (Denmark)

    Flyvbjerg, Bent

    2002-01-01

    This article provides an answer to what has been called the biggest problem in theorizing and understanding planning, namely the ambivalence about power found among planning researchers, theorists, and students. The author narrates how he came to work with issues of power. He then gives an example...... of how the methodology he developed for power studies, called "phronetic planning research," may be employed in practice. Phronetic planning research follows the tradition of power studies running from Machiavelli and Nietzsche to Michel Foucault and Pierre Bourdieu. It focuses on four value......-rational questions: (1) Where are we going with planning? (2) Who gains and who loses, and by which mechanisms of power? (3) Is this development desirable? (4) What should be done? These questions are exemplified for a specific instance of Scandinavian urban planning. The author finds that the questions...

  10. A zero-voltage switching technique for minimizing the current-source power of implanted stimulators.

    Science.gov (United States)

    Çilingiroğlu, Uğur; İpek, Sercan

    2013-08-01

    The current-source power of an implanted stimulator is reduced almost to the theoretical minimum by driving the electrodes directly from the secondary port of the inductive link with a dedicated zero-voltage switching power supply. A feedback loop confined to the secondary of the inductive link adjusts the timing and conduction angle of switching to provide just the right amount of supply voltage needed for keeping the current-source voltage constant at or slightly above the compliance limit. Since drive is based on current rather than voltage, and supply-voltage update is near real-time, the quality of the current pulses is high regardless of how the electrode impedance evolves during stimulation. By scaling the switching frequency according to power demand, the technique further improves overall power consumption of the stimulator. The technique is implemented with a very simple control circuitry comprising a comparator, a Schmitt trigger and a logic gate of seven devices in addition to an on-chip switch and an off-chip capacitor. The power consumed by the proposed supply circuit itself is no larger than what the linear regulator of a conventional supply typically consumes for the same stimulation current. Still, the sum of supply and current-source power is typically between 20% and 75% of the conventional source power alone. Functionality of the proposed driver is verified experimentally on a proof-of-concept prototype built with 3.3 V devices in a 0.18 μm CMOS technology.

  11. Automatic Meter Reading using Power Line Signaling and Voltage Zero-crossing Detection

    Directory of Open Access Journals (Sweden)

    C.L. Vasu

    2015-06-01

    Full Text Available In India, the electric power transmission and distribution loss is very high, about 7% in transmission and 26% in distribution. Though deployment of automated meter reading system will reduce losses, particularly in distribution, penetration of automated meter reading is low due to high costs involved. World over, the Two-Way Automatic Communications System (TWACS is the most widely used power line communications technology offering two-way communication between substation and end users. The TWACS introduces disturbance on the power system voltage for short durations near zero-crossing to generate the outbound (from substation to end user signal. To generate the inbound (from end user to substation signal, short duration current pulses are introduced, near voltage zero-crossings. Information is generated as a sequential combination of voltage disturbances for the outbound signal and current pulses for the inbound signal. The current study proposes a low-cost modification of the TWACS to reduce voltage and current harmonics. The proposed system has been modelled and simulated using SIMULINK/SIMPOWER Systems. The simulation results show that there is a reduction in voltage harmonics from 0.84 to 0.17% and in current harmonics from 2.07 to 1.10%.

  12. Recommended documentation for computer users at ANL

    Energy Technology Data Exchange (ETDEWEB)

    Heiberger, A.A.

    1992-04-01

    Recommended Documentation for Computer Users at ANL is for all users of the services available from the Argonne National Laboratory (ANL) Computing and Telecommunications Division (CTD). This document will guide you in selecting available documentation that will best fill your particular needs. Chapter 1 explains how to use this document to select documents and how to obtain them from the CTD Document Distribution Counter. Chapter 2 contains a table that categorizes available publications. Chapter 3 gives descriptions of the online DOCUMENT command for CMS, and VAX, and the Sun workstation. DOCUMENT allows you to scan for and order documentation that interests you. Chapter 4 lists publications by subject. Categories I and IX cover publications of a general nature and publications on telecommunications and networks respectively. Categories II, III, IV, V, VI, VII, VIII, and X cover publications on specific computer systems. Category XI covers publications on advanced scientific computing at Argonne. Chapter 5 contains abstracts for each publication, all arranged alphabetically. Chapter 6 describes additional publications containing bibliographies and master indexes that the user may find useful. The appendix identifies available computer systems, applications, languages, and libraries.

  13. Building America Case Study: New Town Builders' Power of Zero Energy Center, Denver, Colorado (Brochure)

    Energy Technology Data Exchange (ETDEWEB)

    2014-10-01

    New Town Builders, a builder of energy efficient homes in Denver, Colorado, offers a zero energy option for all the homes it builds. To attract a wide range of potential homebuyers to its energy efficient homes, New Town Builders created a 'Power of Zero Energy Center' linked to its model home in the Stapleton community of Denver. This case study presents New Town Builders' marketing approach, which is targeted to appeal to homebuyers' emotions rather than overwhelming homebuyers with scientific details about the technology. The exhibits in the Power of Zero Energy Center focus on reduced energy expenses for the homeowner, improved occupant comfort, the reputation of the builder, and the lack of sacrificing the homebuyers' desired design features to achieve zero net energy in the home. The case study also contains customer and realtor testimonials related to the effectiveness of the Center in influencing homebuyers to purchase a zero energy home.

  14. New Whole-House Solutions Case Study: New Town Builders' Power of Zero Energy Center - Denver, Colorado

    Energy Technology Data Exchange (ETDEWEB)

    None

    2014-10-01

    New Town Builders, a builder of energy efficient homes in Denver, Colorado, offers a zero energy option for all the homes it builds. To attract a wide range of potential homebuyers to its energy efficient homes, New Town Builders created a "Power of Zero Energy Center" linked to its model home in the Stapleton community. This case study presents New Town Builders' marketing approach, which is targeted to appeal to homebuyers' emotions rather than overwhelming homebuyers with scientific details about the technology. The exhibits in the Power of Zero Energy Center focus on reduced energy expenses for the homeowner, improved occupant comfort, the reputation of the builder, and the lack of sacrificing the homebuyers' desired design features to achieve zero net energy in the home. This case study also contains customer and realtor testimonials related to the effectiveness of the Center in influencing homebuyers to purchase a zero energy home.

  15. Ground Zero in the Debate over Stem-Cell Research.

    Science.gov (United States)

    Southwick, Ron

    2001-01-01

    Describes how political, legal, and ethical battles over embryonic stem-cell research are focused on the University of Wisconsin at Madison, where the cells were first isolated. Addresses the issue of access to the university's stem cells and a recent presidential decision regarding funding for stem-cell research.(EV)

  16. Design and Analysis of the Power Control System of the Fast Zero Energy Reactor FR-0

    Energy Technology Data Exchange (ETDEWEB)

    Schuh, N.J.H.

    1966-12-15

    This report describes the power control by means of the fine-control rod and the design of the control system of the fast zero energy reactor FR-0 located in Studsvik, Sweden. System requirements and some operational conditions were used as design criteria. Manual and automatic control is possible. Variable electronic end-stops for the control rod have been designed, because of the special construction of the reactor and control rod. Noise in the control system caused by the reactor, detector and electronics caused disturbances of the control system at the lower power levels. The noise power-spectrum was measured. Statistical design methods, using the measured noise power spectrum, were used to design filters, which will reduce the influence of the noise at the lower power levels. Root Loci sketches and Bode diagrams were used for stability analyses. The system was simulated on an analogue computer, taking into account even nonlinearities of the control system and noise. Typical cases of reactor operation were simulated and stability analysis performed.

  17. Programmatic Need for a Zero Emission Steam Technology (ZEST) Research Facility

    Energy Technology Data Exchange (ETDEWEB)

    Meltzer, M; Followill, F; Johnson, J

    2001-06-30

    Lawrence Livermore National Laboratory (LLNL) is proposing to construct an on-site research facility for a novel electric power generation system that exploits clean-burning fossil fuels. This system, termed Zero Emission Steam Technology (ZEST), offers unique economic and environmental benefits, including: (1) Highly efficient power generation using the most advanced combustion and turbine technologies. (2) Ability to burn a range of fossil fuels, including natural gas, synthetic gas from coal (''coal syngas''), and coal-bed methane. (3) No oxides of nitrogen generated that would contribute to air pollution. (4) No greenhouse gases emitted. (5) Secure geologic sequestration of the carbon dioxide (CO{sub 2}) combustion product. (6) Use of the CO{sub 2} combustion product to enhance oil recovery in mature fields. The proposed research facility will provide a necessary step toward commercialization of ZEST. Despite the technology's promise, it will not be implemented by the U.S. electric power industry unless an agency such as DOE takes on the task of demonstrating its scientific and economic viability. The U.S. electric power industry typically requires 50,000 hours of operational data--nearly six years of continuous duty--before investing in a major new technology. Hence, there is a strong programmatic need for DOE to provide such data for ZEST, to accelerate commercial investment in this technology. The ZEST combustion process is based on rocket engine technology. It burns pure oxygen with a hydrocarbon fuel under stoichiometric conditions to produce power with virtually no oxides of nitrogen generated. The flexibility of ZEST's gas generator, which has independent temperature and pressure control, will allow modular upgrading of turbine systems as new, more efficient technology becomes available. It is envisioned that the ZEST research facility will serve as a testing laboratory for new turbine technology being designed by the U

  18. Analysis and optimisation of the Zecomix high efficiency zero emission hydrogen and power plant

    Energy Technology Data Exchange (ETDEWEB)

    Antonio Calabro; Paolo Deiana; Paolo Fiorini; Stefano Stendardo; Giuseppe Girardi [ENEA - Italian Agency for New Technologies, Rome (Italy). Energy and Environment

    2005-07-01

    The paper reports the analysis and the optimization of a high efficiency and zero emissions hydrogen and power production plant. The work is part of a larger project named Zecomix, lead by ENEA, studying an integrated process which produces both hydrogen and electricity from coal. A thermodynamic model of the plant has been realized by adopting a commercial software, ChemCAD. The key element of the proposed plant is the integration of the gasification island characterized by coal hydrogasification, simultaneous steam reforming and carbon dioxide sequestration, with the power island. Crucial characteristics involve the regeneration of the CO{sub 2}-acceptor sorbent, that takes place by a calcination process. The needed heat can be supplied directly, by burning additional coal or a part of the produced syngas in the calciner reactor, or indirectly by mean of an high temperature heat exchanger situated downstream the hydrogen combustor. An advanced steam cycle has been considered for power generation consisting of an internal combustion steam cycle characterized by the presence of innovative components such as the medium pressure steam compressor and medium-pressure high-temperature expander. Possible steps for the optimization of the whole plant have been studied. The solution proposed aims also to identify the most feasible plant configuration, adopting, where possible, current technology solution. The plant could reach an energy conversion efficiency close to 54%, competitive with innovative power cycle proposed in other studies. 6 refs., 3 figs., 2 tabs.

  19. EVALUATION OF ZERO-POWER, ELEVATED-TEMPERATURE MEASUREMENTS AT JAPAN’S HIGH TEMPERATURE ENGINEERING TEST REACTOR

    Energy Technology Data Exchange (ETDEWEB)

    John D. Bess; Nozomu Fujimoto; James W. Sterbentz; Luka Snoj; Atsushi Zukeran

    2011-03-01

    The High Temperature Engineering Test Reactor (HTTR) of the Japan Atomic Energy Agency (JAEA) is a 30 MWth, graphite-moderated, helium-cooled reactor that was constructed with the objectives to establish and upgrade the technological basis for advanced high-temperature gas-cooled reactors (HTGRs) as well as to conduct various irradiation tests for innovative high-temperature research. The core size of the HTTR represents about one-half of that of future HTGRs, and the high excess reactivity of the HTTR, necessary for compensation of temperature, xenon, and burnup effects during power operations, is similar to that of future HTGRs. During the start-up core physics tests of the HTTR, various annular cores were formed to provide experimental data for verification of design codes for future HTGRs. The experimental benchmark performed and currently evaluated in this report pertains to the data available for two zero-power, warm-critical measurements with the fully-loaded HTTR core. Six isothermal temperature coefficients for the fully-loaded core from approximately 340 to 740 K have also been evaluated. These experiments were performed as part of the power-up tests (References 1 and 2). Evaluation of the start-up core physics tests specific to the fully-loaded core (HTTR-GCR-RESR-001) and annular start-up core loadings (HTTR-GCR-RESR-002) have been previously evaluated.

  20. Initial RattleSnake Calculations of the Hot Zero Power BEAVRS

    Energy Technology Data Exchange (ETDEWEB)

    M. Ellis; J. Ortensi; Y. Wang; K. Smith; R.C. Martineau

    2014-01-01

    The validation of the Idaho National Laboratory's next generation of reactor physics analysis codes is an essential and ongoing task. The validation process requires a large undertaking and includes detailed, realistic models that can accurately predict the behavior of an operational nuclear reactor. Over the past few years the INL has developed the RattleSnake application and supporting tools on the MOOSE framework to perform these reactor physics calculations. RattleSnake solves the linearized Boltzmann transport equation with a variety of solution meth­ ods. Various traditional reactor physics benchmarks have already been performed, but a more realistic light water reactor comparison was needed to solidify the status of the code and deter­ mine its fidelity. The INL team decided to use the Benchmark for Evaluation and Validation of Reactor Simulations, which was made available in early 2013. This benchmark is a one­ of-a-kind document assembled by the Massachusetts Institute of Technology, which includes two cycles of detailed, measured PWR operational data. The results from this initial study of the hot zero power conditions show the current INL analysis procedure with DRAGON4 cross section preparation and using the low order diffusion solver in RattleSnake for the whole core calculations yield very encouraging results for PWR analysis. The radial assembly power distributions, radial detector measurements and control rod worths were computed with good accuracy. The computation of the isothermal temperature coefficients of reactivity require further study.

  1. Hot Zero and Full Power Validation of PHISICS RELAP-5 Coupling

    Energy Technology Data Exchange (ETDEWEB)

    F. Lodi; C. Rabiti; A. Alfonsi; A. Epiney; M. Sumini

    2013-06-01

    PHISICS is a reactor analysis toolkit developed in the last 3 years at the Idaho National Laboratory that has been also coupled with the thermo-hydraulic plant simulator RELAP5-3D. PHISICS is aimed to provide an optimal trade off between needed computational resources and accuracy in the range of 10~100 cores. In fact this range has been identified as the next 5 to 10 years average computational capability available to nuclear engineer designing and optimizing nuclear reactor cores. Different publication has been already presented [1] showing test of the single modules composing the PHISICS package. Lately the Idaho National Laboratory had the opportunity to access to plant data for the first cycle of a PWR including Hot Zero Power (HZP) and Hot Full Power (HFP). This data provided the opportunity to validate the transport solver, the interpolation capability for mixed macro and micro cross section and the criticality search option of the PHISICS package. In the following we will firstly recall briefly the structure of the different PHISICS modules and then we will illustrate the modeling process and some preliminary results.

  2. A novel concentrator with zero-index metamaterial for space solar power station

    Science.gov (United States)

    Huang, Jin; Chu, Xue-mei; Fan, Jian-yu; Jin, Qi-bao; Duan, Zhu-zhu

    2017-03-01

    Space solar power station (SSPS) is a comprehensive system that continuously collects solar energy in space and transmits it to ground with a wireless power transmission (WPT) system. These systems have great potential to provide large-scale energy. To increase the efficiency and reduce the weight and cost of the photovoltaic (PV) components, a huge light-weighted concentrator was introduced in the latest SSPS concepts, such as integrated symmetrical concentrator (ISC) and arbitrarily large phased array (ALPHA). However, for typical SSPS running in Geostationary Earth Orbit (GEO), the sunlight direction varies with time, leading to a great challenge for concentrator design. In ISC, the two-dimensional mast is used to realize sun-tracking. However, a multi-thousand-ton structure is difficult to control precisely in space. For this reason, ALPHA comprises a large number of individually pointed thin-film reflectors to intercept sunlight, mounted on the non-moving structure. However, the real-time adjustment of the thousands of reflectors is still an open problem. Furthermore, the uniformity of the time of the power generation (UTPG) is another factor evaluating the system. Therefore, this paper proposes a novel concentrator based on zero-index metamaterial (ZIM) called Thin-film Energy Terminator (SSPS-TENT). This will aid the control of the massive reflectors while avoiding the rotation of the overall system, the control of the massive reflectors and the influence of the obliquity of the ecliptic. Also, an optimization design method is proposed to increase its solar energy collecting efficiency (ECE) and flux distribution (FD). The ray-tracing simulation results show that the ECE is more than 96% of the day. In terms of the FD, the uniformity varies from 0.3057 to 0.5748. Compared with ALPHA, the UTPG is more stable.

  3. Zero-crossing angle in the np analyzing power at medium energies and its relation to charge symmetry

    Science.gov (United States)

    Bhatia, T. S.; Glass, G.; Hiebert, J. C.; Northcliffe, L. C.; Tippens, W. B.; Bonner, B. E.; Simmons, J. E.; Hollas, C. L.; Newsom, C. R.; Riley, P. J.; Ransome, R. D.

    1981-08-01

    The angle at which the analyzing power for free np scattering becomes zero, the zero-crossing angle θ0, has been measured simultaneously for the n-->p and np--> scattering processes at 425, 565, and 665 MeV incident neutron energies. A rather strong energy dependence of the zerocrossing angle is found. Knowledge of this energy dependence is important in designing an experiment which tests for charge symmetry breaking forces by comparing high precision measurements of θ0(n-->p) and θ0(np-->). [NUCLEAR REACTIONS p(n,p)n, E=425,565, and 665 MeV; polarized neutron beam, polarized proton target; measured analyzing powers A(E,θ) deduced zero-crossing angles; charge symmetry.

  4. Determination of refractive index of a simple negative, positive, or zero power lens using wedged plated interferometer

    Science.gov (United States)

    Shukla, R. P.; Perera, G. M.; George, M. C.; Venkateswarlu, P.

    1990-01-01

    A nondestructive technique for measuring the refractive index of a negative lens using a wedged plate interferometer is described. The method can be also used for measuring the refractive index of convex or zero power lenses. Schematic diagrams are presented for the use of a wedged plate interferometer for measuring the refractive index of a concave lens and of a convex lens.

  5. Evaluation of organics removal options. A case study from a zero liquid discharge power plant

    Energy Technology Data Exchange (ETDEWEB)

    Quagraine, Emmanuel K.; Hill, Keith Dean; Omorogbe, Fredrick [Shand Power Station, Estevan (Canada)

    2010-01-15

    Although the role of organics in power plant cycle chemistry still appears to be controversial, their adverse effects in the course of makeup water treatment are very familiar and include fouling of ion exchange resins. This paper describes the organic/bio-fouling experience in a boiler makeup water treatment train for a zero liquid discharge plant, which draws on treated sewage water and surface water for cooling and utilizes the cooling tower blowdown to make distillate water from an evaporator prior to final treatment with a mixed bed demineralizer. In a case study, which is the focus of this paper, the performance of the pilot plants of two recommended organic removal techniques (i.e. reverse osmosis and organic trap resin) were compared to the existing activated carbon bed for organic removal prior to the mixed beds. Parameters evaluated for these three techniques (before and after each unit) include bacteria plate counts, organic carbons, inorganic nutrients (e.g. NH{sub 3}-N, [NO{sub 3}{sup -}+ NO{sub 2}{sup -}]-N, P, Mn, and Fe), known parameters that could significantly impact on the performance of the mixed beds (i.e. SiO{sub 2}, Cl{sup -}, SO{sub 4}{sup 2-}, Na{sup +}), and various others like pH, conductivity, turbidity, HCO{sub 3}{sup -} etc. The effects of oxidizing (i.e. bleach) and non-oxidizing (glutaraldehyde) biocides on the performance of the activated carbon filter were also evaluated.

  6. A zero power harmonic transponder sensor for ubiquitous wireless μL liquid-volume monitoring.

    Science.gov (United States)

    Huang, Haiyu; Chen, Pai-Yen; Hung, Cheng-Hsien; Gharpurey, Ranjit; Akinwande, Deji

    2016-01-06

    Autonomous liquid-volume monitoring is crucial in ubiquitous healthcare. However, conventional approach is based on either human visual observation or expensive detectors, which are costly for future pervasive monitoring. Here we introduce a novel approach based on passive harmonic transponder antenna sensor and frequency hopping spread spectrum (FHSS) pattern analysis, to provide a very low cost wireless μL-resolution liquid-volume monitoring without battery or digital circuits. In our conceptual demonstration, the harmonic transponder comprises of a passive nonlinear frequency multiplier connected to a metamaterial-inspired 3-D antenna designed to be highly sensitive to the liquid-volume within a confined region. The transponder first receives some FHSS signal from an interrogator, then converts such signal to its harmonic band and re-radiates through the antenna sensor. The harmonic signal is picked up by a sniffer receiver and decoded through pattern analysis of the high dimensional FHSS signal strength data. A robust, zero power, absolute accuracy wireless liquid-volume monitoring is realized in the presence of strong direct coupling, background scatters, distance variance as well as near-field human-body interference. The concepts of passive harmonic transponder sensor, metamaterial-inspired antenna sensor, and FHSS pattern analysis based sensor decoding may help establishing cost-effective, energy-efficient and intelligent wireless pervasive healthcare monitoring platforms.

  7. Estimation of ground reaction force and zero moment point on a powered ankle-foot prosthesis.

    Science.gov (United States)

    Martinez-Villalpando, Ernesto C; Herr, Hugh; Farrell, Matthew

    2007-01-01

    The ground reaction force (GRF) and the zero moment point (ZMP) are important parameters for the advancement of biomimetic control of robotic lower-limb prosthetic devices. In this document a method to estimate GRF and ZMP on a motorized ankle-foot prosthesis (MIT Powered Ankle-Foot Prosthesis) is presented. The method proposed is based on the analysis of data collected from a sensory system embedded in the prosthetic device using a custom designed wearable computing unit. In order to evaluate the performance of the estimation methods described, standing and walking clinical studies were conducted on a transtibial amputee. The results were statistically compared to standard analysis methodologies employed in a gait laboratory. The average RMS error and correlation factor were calculated for all experimental sessions. By using a static analysis procedure, the estimation of the vertical component of GRF had an averaged correlation coefficient higher than 0.94. The estimated ZMP location had a distance error of less than 1 cm, equal to 4% of the anterior-posterior foot length or 12% of the medio-lateral foot width.

  8. Innovative oxy-coal combustion process suitable for future and more efficient zero emission power plants

    Energy Technology Data Exchange (ETDEWEB)

    Benelli, G.; Malavasi, M.; Girardi, G. [ENEL Ricerca (Italy)

    2007-07-01

    The problem with CO{sub 2} capture from a flue gas stream is related to its low concentration, which makes the process of separation very energy-intensive, complex and, as a result, expensive. The CO{sub 2} separation process can be optimized by increasing the concentration of CO{sub 2} and reducing nitrogen concentration in the stream as it happens, in the oxy-fuel combustion process. In such a case, the oxidant flow is typically a mixture of oxygen, steam and carbon dioxide, with a very low concentration of nitrogen. Since the oxy-combustion process leads to very high temperatures, flue gases must be circulating through the chemical reactor to keep the combustion adiabatic temperature below acceptable values, due to the limits imposed by material resistance. This paper focuses on an innovative oxy-coal combustion process named ISOTHERM{reg_sign}, based on a flameless combustion technique which is mentioned in recent literature also as 'Mild' combustion. The combustion process takes place within a pressurized and refractory-lined furnace, approaching temperatures close to 2000 K. The process has been experienced at pressurized conditions up to 4 bar on a 5 MW pilot plant for thousands of hours. In this paper, starting from a detailed description of the process, results obtained by the preliminary experimental tests are presented and discussed. Then, a development and demonstration program to assess the suitability of this technology for zero emission power generation at large scale in one of the units of Brindisi power station is presented. 10 refs., 5 figs., 2 tabs.

  9. Hierarchical Control Strategy of Heat and Power for Zero Energy Buildings including Hybrid Fuel Cell/Photovoltaic Power Sources and Plug-in Electric Vehicle

    DEFF Research Database (Denmark)

    Ghiasi, Mohammad Iman; Aliakbar Golkar, Masoud; Hajizadeh, Amin

    2016-01-01

    complexities and uncertainties in this kind of hybrid system, a hybrid supervisory control with an adaptive fuzzy sliding power control strategy is proposed to regulate the amount of requested fuel from a fuel cell power source to produce the electrical power and heat. Then, simulation results are used......This paper presents a hierarchical control strategy for heat and electric power control of a building integrating hybrid renewable power sources including photovoltaic, fuel cell and battery energy storage with Plug-in Electric Vehicles (PEV) in smart distribution systems. Because...... of the controllability of fuel cell power, this power sources plays the main role for providing heat and electric power to zero emission buildings. First, the power flow structure between hybrid power resources is described. To do so, all necessary electrical and thermal equations are investigated. Next, due to the many...

  10. Research on optimal allocation of rescue resources for forest fire in Daxing'anling%大兴安岭森林火灾应急资源优化调度研究

    Institute of Scientific and Technical Information of China (English)

    杨忠振; 郭利泉; 董夏丹

    2014-01-01

    针对大兴安岭森林火灾救援中的单出救点、多需求点的二级应急资源分配系统,首先,基于大兴安岭森林火灾的发生规律、火势蔓延的影响因子,以及火势蔓延模式,改进已有的林火火势蔓延趋势模型。其次,根据着火点火势蔓延速度,区分受灾点灾情程度,确定分配应急资源的优先度。最后,进行应急资源分配和救援消防车辆的优化调度。针对前者,以森林损失和救援开支费用最小为目标,建立资源分配优化模型;针对后者,以火灾应急物流系统所需时间最少和费用最小为目标,建立多目标优化模型,并用免疫克隆算法进行求解。实例证明该模型完善了森林火灾救援中应急资源调度体系,为资源的合理调配提供了指导。%For the rescue resources allocation system consisting of single depot and multi-demand sites in Daxing'anling forest fire emergency,the existing flame spread trend model is firstly improved by studying the regularity and characteristics of the forest fires which had happened in Daxing'anling, the factors affecting the flame spread and the flame spread styles.Secondly,based on the flame spread speed,the damage degrees in the sites are distinguished and the allocation priority of rescue resources is determined.Finally,the problems of allocating rescue resources and dispatching fire engines are studied.For the former,a model is established under the condition of minimizing the forest loss and rescue cost.For the latter,a multi-objective optimization model is built with the objective to minimize the needed time and costs,and immune clonal algorithm is used to solve the model.Examples prove that the model can improve the rescue resources allocation system for forest fire,and provide guidance for reasonable resources arrangement.

  11. Power Relations: Their Embodiment in Research.

    Science.gov (United States)

    Florczak, Kristine L

    2016-07-01

    The purpose of this column is to consider the notion of power in research. To that end, the idea of power is considered from the perspective of philosophy and then linked to a nursing concept analysis that compares the differences between power over and power to. Then, the nature of power relations is compared and contrasted between quantitative and qualitative methodologies.

  12. 内蒙古大兴安岭兴安落叶松土壤种子库研究%Research on Soil Seeds Bank of Larix gmelini Community in Daxing'anling Mountain

    Institute of Scientific and Technical Information of China (English)

    郭鑫; 周海峰; 卢立娜; 贺晓辉; 李维向; 杨宏伟; 王利兵

    2015-01-01

    对内蒙古大兴安岭成熟兴安落叶松纯林的3种不同采伐林分类型(原始林、渐伐林、皆伐林)的土壤种子库储量、质量及其垂直分布(枯枝落叶层、土层0~5cm 和5~10cm)进行了研究,结果表明:不同的采伐林分生长状况,决定了不同的土壤种子储量,渐伐林种子储量最多,皆伐林种子储量最小;从种子库活力程度看,种子整体质量非常差,完整种子中大部分为空粒种子,各林分均为70%左右;土壤种子库中种子集中分布在枯枝落叶层中;各林分林下均有幼苗,表明兴安落叶松纯林土壤种子库种子具有一定的萌发能力。%The density,quality and vertical distribution(litter layer,soil layer 0 ~5 cm and 5 ~10 cm)of soil seed bank of 3 different cutting types(virgin forest、successive cutting forest,clear-cutting forests)on maturation of Larix gmelini pure forest in Daxing'anling Mountains were investigated.The results showed that 1)growth status of cutting forests determines soil seed densities and the successive cutting forest had the largest seed reserves and clear-cutting forest was the minimum,2)the seed qualities were low and al-most 70% seeds were empty in each stand,3)soil seeds intensively distribute in litter layer,4)each stand had understory seedings which indicated that the soil seed bank of Larix gmelini pure forest had cer-tain potential of germination.

  13. Research Developments on Power System Integration of Wind Power

    DEFF Research Database (Denmark)

    Chen, Zhe; Hansen, Jens Carsten; Qiuwei, Wu;

    2011-01-01

    This paper presents an overview on the recent research activities and tendencies regarding grid integration of wind power in Denmark and some related European activities, including power electronics for enhancing wind power controllability, wind turbines and wind farms modeling,wind power...... variability and prediction, wind power plant ancillary services, grid connection and operation, Smart grids and demand side management under market functionality. The topics of the first group of PhD program starting 2011 under the wind energy Sino-Danish Centre for Education & Research (SDC) are also...

  14. Research Overview on Wireless Power Transmission Technology

    OpenAIRE

    Li Tao; Wu Liheng; Chen Zheng

    2015-01-01

    According to the latest researches, this paper outlines the development of wireless power transmission and introduces the latest applications of wireless power transmission in life. To describe the wireless power transmission technologies in detail, the paper presents the short-range, medium-range and remote wireless power transmission, respectively. In addition, the paper also depicts some unique properties of wireless power transmission system to make readers understand WPT system better. A...

  15. RESEARCH ACTION: IMPLEMENTATION ZERO BASED BUDGET (ZBB IN THE PROVIDER SERVICE LEASING EQUIPAMENTS OF CARGO HANDLING.

    Directory of Open Access Journals (Sweden)

    Levi Gimenez

    2013-06-01

    Full Text Available This article aims to present the implementation of zero-based budgeting in a rental service provider of cargo handling equipment using the action research methodology. The goal was to examine the possibility of concomitant use of this instrument in service providers in need of accurate information that enables targeting at the best result in a setting avid for quick decisions and actions. Action research was used as research method. It was concluded that it is suitable for this branch, confirming its position as a useful model for restructuring and cutting costs, improving operational and financial results, and as a factor improving organizational environment (behavioral aspects, indirectly creating value to stakeholders.

  16. Advancing Concentrating Solar Power Research (Fact Sheet)

    Energy Technology Data Exchange (ETDEWEB)

    2014-02-01

    Researchers at the National Renewable Energy Laboratory (NREL) provide scientific, engineering, and analytical expertise to help advance innovation in concentrating solar power (CSP). This fact sheet summarizes how NREL is advancing CSP research.

  17. A User’s Guide to the PLTEMP/ANL Code

    Energy Technology Data Exchange (ETDEWEB)

    Olson, A. P. [Argonne National Lab. (ANL), Argonne, IL (United States); Kalimullah, M. [Argonne National Lab. (ANL), Argonne, IL (United States); Feldman, E. E. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-07-25

    PLTEMP/ANL V4.2 is a program that obtains a steady-state flow and temperature solution for a nuclear reactor core, or for a single fuel assembly. It is based on an evolutionary sequence of codes originally used for plate temperatures, hence “PLTEMP”, developed at Argonne National Laboratory over several decades. Fueled and non-fueled regions are modeled. Each fuel assembly consists of one or more plates or tubes separated by coolant channels. The fuel plates may have one to five layers of different materials, each with heat generation. The width of a fuel plate may be divided into multiple longitudinal stripes, each with its own axial power shape. The temperature solution is effectively 2-dimensional. It begins with a one-dimensional solution across all coolant channels and fuel plates or tubes within a given fuel assembly, at the entrance to the assembly. The temperature solution is repeated for each axial node along the length of the fuel assembly. The geometry may be either slab or radial, corresponding to fuel assemblies made of a series of flat (or slightly curved) plates, or of nested tubes. A variety of thermal-hydraulic correlations are available with which to determine safety margins such as onset-of-nucleate boiling ratio(ONBR), departure from nucleate boiling ratio (DNBR), and onset of flow instability ratio (OFIR). Coolant properties for either light or heavy water are obtained from FORTRAN functions rather than from tables. The code is intended for thermal-hydraulic analysis of research reactor performance in the sub-cooled boiling regime. Both turbulent and laminar flow regimes can be modeled. Options to calculate both forced flow and natural circulation are available. A general search capability is available (Appendix XII) to greatly reduce the reactor analyst’s time.

  18. Wireless power transmission for biomedical implants: The role of near-zero threshold CMOS rectifiers.

    Science.gov (United States)

    Mohammadi, Ali; Redoute, Jean-Michel; Yuce, Mehmet R

    2015-01-01

    Biomedical implants require an electronic power conditioning circuitry to provide a stable electrical power supply. The efficiency of wireless power transmission is strongly dependent on the power conditioning circuitry specifically the rectifier. A cross-connected CMOS bridge rectifier is implemented to demonstrate the impact of thresholds of rectifiers on wireless power transfer. The performance of the proposed rectifier is experimentally compared with a conventional Schottky diode full wave rectifier over 9 cm distance of air and tissue medium between the transmitter and receiver. The output voltage generated by the CMOS rectifier across a 1 KΩ resistive load is around twice as much as the Schottky rectifier.

  19. Power Analysis Software for Educational Researchers

    Science.gov (United States)

    Peng, Chao-Ying Joanne; Long, Haiying; Abaci, Serdar

    2012-01-01

    Given the importance of statistical power analysis in quantitative research and the repeated emphasis on it by American Educational Research Association/American Psychological Association journals, the authors examined the reporting practice of power analysis by the quantitative studies published in 12 education/psychology journals between 2005…

  20. Research in power systems: power quality and electricity market

    OpenAIRE

    Amarís Duarte, Hortensia; Usaola, Julio

    2008-01-01

    The research group REDES from UC3M has experience on electricity market, grid integration of wind energy and power quality. The group may offer consulting activities with a high component of research. We are looking for the collaboration of companies devoted to the consulting related to electricity markets, the integration of wind power in the electricity network, and with power quality. Contrato Programa de Comercialización e Internacionalización. Sistema Regional de Investigación Científ...

  1. Analysis of Zero CO2 Emission SOFC Hybrid Power System%CO2零排放的SOFC复合动力系统分析

    Institute of Scientific and Technical Information of China (English)

    张潇元; 段立强

    2011-01-01

    Based on the Aspen-plus soft, SOFC stack model is established. The SOFC hybrid power system without CO2 capture is designed. Then, the zero CO2 emission SOFC hybrid power system is proposed. The performances of these two systems are compared and analyzed. With the mode of pure oxygen combustion, the outlet gas of zero CO2 emission SOFC hybrid power system is composed of only CO2 and steam, so it is easy to get CO2 with higher concentration by means of condensation. Compared with the conventional power system with CO2 capture, the energy consumption of CO2 capture in the new system decreases a lot. This paper also analyzes the effects of the main parameters on the performance of the hybrid power system. Above research achievements will provide the useful guide for further study on zero CO2 emission SOFC hybrid power system.%基于Aspen-Plus软件建立了SOFC电池堆的模型,设计了不回收CO2的SOFC复合动力系统,针对系统特点,提出了CO2零排放的SOFC复合动力系统,对这两种系统的性能进行了详细的比较和分析.CO2零排放系统利用纯氧燃烧方式得到的燃烧产物只有CO2和水蒸气,通过冷凝得到高浓度的CO2.与带CO2脱除的常规电厂相比,极大地降低了回收CO2的能耗.通过对主要参数(燃料利用率、蒸汽/碳比、运行压力等)进行优化,详细分析了各主要参数对系统性能的影响.本文研究成果将为进一步研究高效的CO2零排放SOFC复合动力系统提供有益的参考.

  2. Degradation modeling of the ANL ceramic waste form

    Energy Technology Data Exchange (ETDEWEB)

    Fanning, T. H.; Morss, L. R.

    2000-03-28

    A ceramic waste form composed of glass-bonded sodalite is being developed at Argonne National Laboratory (ANL) for immobilization and disposition of the molten salt waste stream from the electrometallurgical treatment process for metallic DOE spent nuclear fuel. As part of the spent fuel treatment program at ANL, a model is being developed to predict the long-term release of radionuclides under repository conditions. Dissolution tests using dilute, pH-buffered solutions have been conducted at 40, 70, and 90 C to determine the temperature and pH dependence of the dissolution rate. Parameter values measured in these tests have been incorporated into the model, and preliminary repository performance assessment modeling has been completed. Results indicate that the ceramic waste form should be acceptable in a repository environment.

  3. Management and construction of a major zero discharge water supply and treatment scheme at Mount Piper Power Station, Australia

    Energy Technology Data Exchange (ETDEWEB)

    Wong, P.; Docker, P.; Gabbrielli, E.; Wade, P. [Pacific Power, Sydney, NSW (Australia)

    1994-09-01

    Excellence in the organisation and management of a large multi-disciplinary design and construct project such as the zero discharge water supply and treatment scheme for Mount Piper coal-fired power station was essential to its successful execution. This paper discusses the management philosophies and strategies of Pacific Power and Transfield-PWT Asia/Pacific that resulted in this project being completed to the satisfaction of the client in the minimum time without delays and cost increases caused by interfaces between the parties. It highlights the advantages of contract packaging and placing the total responsibility for the performance and integration of a complex project system on one organisation. 2 refs., 6 figs.

  4. Three-Phase High-Power and Zero-Current-Switching OBC for Plug-In Electric Vehicles

    Directory of Open Access Journals (Sweden)

    Cheng-Shan Wang

    2015-06-01

    Full Text Available In this paper, an interleaved high-power zero-current-switching (ZCS onboard charger (OBC based on the three-phase single-switch buck rectifier is proposed for application to plug-in electric vehicles (EVs. The multi-resonant structure is used to achieve high efficiency and high power density, which are necessary to reduce the volume and weight of the OBC. This study focuses on the border conditions of ZCS converting with a battery load, which means the variation ranges of the output voltage and current are very large. Furthermore, a novel hybrid control method combining pulse frequency modulation (PFM and pulse width modulation (PWM together is presented to ensure a driving frequency higher than 10 kHz, and this will reduce the unexpected inner resonant power flow and decrease the total harmonic distortion (THD of the input current under a light load at the end of the charging process. Finally, a prototype is established, and experiments are carried out. According to the experimental results, the conversion efficiency is higher than 93.5%, the THD about 4.3% and power factor (PF 0.98 under the maximum power output condition. Besides, a three-stage charging process is also carried out the experimental platform.

  5. Researcher/Researched: Relations of Vulnerability/Relations of Power

    Science.gov (United States)

    Huckaby, M. Francyne

    2011-01-01

    Turning to reflexive journals and fieldnotes, the author reconsiders Foucault's "relations of power" through her experiences with five research participants, who are professors of education. The paper explores: (1) the translation of Foucault for an analysis of power; (2) the dynamics of researching up and analyzing from below; and (3) the…

  6. Research of the Power Plant Operational Modes

    Directory of Open Access Journals (Sweden)

    Koismynina Nina M.

    2017-01-01

    Full Text Available In this article the algorithm of the power plant operational modes research is offered. According to this algorithm the program for the modes analysis and connection power transformers choice is developed. The program can be used as educational means for studying of the power plant electric part, at the same time basic data are provided. Also the program can be used for the analysis of the working power plants modes. Checks of the entered data completeness and a choice correctness of the operational modes are provided in the program; in all cases of a deviation from the correct decisions to the user the relevant information is given.

  7. Research Developments on Power System Integration of Wind Power

    DEFF Research Database (Denmark)

    Chen, Zhe; Hansen, Jens Carsten; Wu, Qiuwei

    2011-01-01

    variability and prediction, wind power plant ancillary services, grid connection and operation, Smart grids and demand side management under market functionality. The topics of the first group of PhD program starting 2011 under the wind energy Sino-Danish Centre for Education & Research (SDC) are also...

  8. Power Control Method for Research Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Baang, Dane; Suh, Yongsuk; Park, Cheol [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2015-05-15

    Considering safety-oriented design concept and other control environment, we developed a simple controller that provides limiting function of power change- rate as well as fine tracking performance. The design result has been well-proven via simulation and actual application to a TRIGA-II type research reactor. The proposed controller is designed to track the PDM(Power Demand) from operator input as long as maintaining the power change rate lower than a certain value for stable reactor operation. A power control method for a TRIGA-II type research reactor has been designed, simulated, and applied to actual reactor. The control performance during commissioning test shows that the proposed controller provides fine control performance for various changes in reference values (PDM), even though there is large measurement noise from neutron detectors. The overshoot at low power level is acceptable in a sense of reactor operation.

  9. Zero Power Buoyancy Control for Distributed Autonomous Sensor Networks Conducted During Crimson Viper 2010 Field Experiment

    Science.gov (United States)

    2011-03-04

    STATEMENT 13. SUPPLEMENTARY NOTES 14. ABSTRACT 15. SUBJECT TERMS 16. SECURITY CLASSIFICATION OF: a. REPORT 19a. NAME OF RESPONSIBLE PERSON 19b. TELEPHONE...producing simple, small, power-efficient data harvesting nodes with variable buoyancy, enabling unsupervised underwater sensing with subsequent surfacing...aerosol samples for subsequent analysis at NRL. At regular intervals, a hand-held hyperspectral sensor as to be used to collect near-water optical

  10. Thermal noise informatics: Totally secure communication via a wire; Zero-power communication; and Thermal noise driven computing

    CERN Document Server

    Kish, Laszlo B; gingl, Zoltan

    2007-01-01

    Very recently, it has been shown that Gaussian thermal noise and its artificial versions (Johnson-like noises) can be utilized as an information carrier with peculiar properties therefore it may be proper to call this topic Thermal Noise Informatics. Zero Power (Stealth) Communication, Thermal Noise Driven Computing, and Totally Secure Classical Communication are relevant examples. In this paper, while we will briefly describe the first and the second subjects, we shall focus on the third subject, the secure classical communication via wire. This way of secure telecommunication utilizes the properties of Johnson(-like) noise and those of a simple Kirchhoff's loop. The communicator is unconditionally secure at the conceptual (circuit theoretical) level and this property is (so far) unique in communication systems based on classical physics. The communicator is superior to quantum alternatives in all known aspects, except the need of using a wire.

  11. Excitation Method of Linear-Motor-Type Rail Brake without Using Power Sources by Dynamic Braking with Zero Electrical Output

    Science.gov (United States)

    Sakamoto, Yasuaki; Kashiwagi, Takayuki; Hasegawa, Hitoshi; Sasakawa, Takashi; Fujii, Nobuo

    The eddy current rail brake is a type of braking system used in railway vehicles. Because of problems such as rail heating and problems associated with ensuring that power is supplied when the feeder malfunctions, this braking system has not been used for practical applications in Japan. Therefore, we proposed the use of linear induction motor (LIM) technology in eddy current rail brake systems. The LIM rail brake driven by dynamic braking can reduce rail heating and generate the energy required for self-excitation. In this paper, we present an excitation system and control method for the LIM rail brake driven by “dynamic braking with zero electrical output”. The proposed system is based on the concept that the LIM rail brake can be energized without using excitation power sources such as a feeder circuit and that high reliability can be realized by providing an independent excitation system. We have studied this system and conducted verification tests using a prototype LIM rail brake on a roller rig. The results show that the system performance is adequate for commercializing the proposed system, in which the LIM rail brake is driven without using any excitation power source.

  12. Effect of age on inter and intra-subject variability in acceptable noise level (ANL in listeners with normal hearing

    Directory of Open Access Journals (Sweden)

    Bankole K. Fasanya

    2013-02-01

    Full Text Available Several industrial engineering and psychological studies have shown that noise affects the important aspects of communication for both adults and children. For speech understanding by hearing aids users and language development in children, an accurate hearing is very important. A metric has been developed for measuring an individual's acceptance of noise while listening to speech in quiet. This metric is known as Acceptable Noise Levels (ANLs. Studies have shown large inter-subject variability in acceptance of background noise. An argument has been made that an acceptance of background noise is a “means” that will help to solve the puzzle and monumental problem of hearing aid rejection. Meanwhile, within subject age dependency has not been investigated. This study is conducted to determine if ANL inter and intra-subject variability under music signal depends on age. Twenty subjects participated in the study (average age = 29; SD = 3.7; range 23-35 years. All participants had hearing level not worse than 25dB HL at octave frequencies from 250Hz to 4000Hz. Listeners’ task was to adjust the level of music played in quiet to their most comfortable listening level and then to adjust the level of background noise to the maximum level that they still consider acceptable while listening to music. Further, music is not a speech signal that many researchers have used to determine the significance of age on ANL inter-subject variability. Results of this study supported the findings of others on age dependency, which shows that ANL inter and intra-subject variability is independent of age.

  13. Experimental Setup for the Measurement of the Thermoelectric Power in Zero and Applied Magnetic Field

    CERN Document Server

    Mun, Eundeok; Torikachvili, Milton S; Canfield, Paul C

    2010-01-01

    An experimental setup was developed for the measurement of the thermoelectric power (TEP, Seebeck coefficient) in the temperature range from 2 to 350 K and magnetic fields up to 140 kOe. The system was built to fit in a commercial cryostat and is versatile, accurate and automated; using two heaters and two thermometers increases the accuracy of the TEP measurement. High density data of temperature sweeps from 2 to 350 K can be acquired in under 16 hours and high density data of isothermal field sweeps from 0 to 140 kOe can be obtained in under 2 hours. Calibrations for the system have been performed on a platinum wire and Bi$_{2}$Sr$_{2}$CaCu$_{2}$O$_{8+\\delta}$ high $T_{c}$ superconductors. The measured TEP of phosphor-bronze (voltage lead wire) turns to be very small, where the absolute TEP value of phosphor-bronze wire is much less than 0.5 $\\mu$V/K below 80 K. For copper and platinum wires measured against to the phosphor-bronze wire, the agreement between measured results and the literature data is good....

  14. The Zero Emission Fossil Fuel Power Plant - from vision to reality.

    Energy Technology Data Exchange (ETDEWEB)

    Stroemberg, L.; Sauthoff, M.

    2007-07-01

    Sufficient supply of energy without fossil fuels is not possible the next fifty years. Thus, we must find a solution to use coal, without endangering the environment. Carbon Capture and Storage, CCS, might be the answer. At a cost of about 20 Euro/ton CO{sub 2}, there exist technologies, which can be ready for commercial application in 2020. After that, even more cost effective technologies will be developed. To reduce emissions by more than half until 2050, cannot be reached without CCS. However, CCS is very powerful, but not the only tool. All ways to reduce emissions, including renewables and nuclear must be used. To put emphasis behind the words, Vattenfall has started an R and D program to develop technology for CCS in a ten year program. As part of that, Vattenfall is building a Pilot Plant including all process steps from coal input to liquid CO{sub 2}. It will be ready in 2008. In parallel, preparations for a demonstration plant are ongoing. It will be a coal fired full size plant with storage on shore. That will be ready for operation in 2015. (auth)

  15. Recommended documentation for computer users at ANL. Revision 3

    Energy Technology Data Exchange (ETDEWEB)

    Heiberger, A.A.

    1992-04-01

    Recommended Documentation for Computer Users at ANL is for all users of the services available from the Argonne National Laboratory (ANL) Computing and Telecommunications Division (CTD). This document will guide you in selecting available documentation that will best fill your particular needs. Chapter 1 explains how to use this document to select documents and how to obtain them from the CTD Document Distribution Counter. Chapter 2 contains a table that categorizes available publications. Chapter 3 gives descriptions of the online DOCUMENT command for CMS, and VAX, and the Sun workstation. DOCUMENT allows you to scan for and order documentation that interests you. Chapter 4 lists publications by subject. Categories I and IX cover publications of a general nature and publications on telecommunications and networks respectively. Categories II, III, IV, V, VI, VII, VIII, and X cover publications on specific computer systems. Category XI covers publications on advanced scientific computing at Argonne. Chapter 5 contains abstracts for each publication, all arranged alphabetically. Chapter 6 describes additional publications containing bibliographies and master indexes that the user may find useful. The appendix identifies available computer systems, applications, languages, and libraries.

  16. Zero-Power-Consumption Solar-Blind Photodetector Based on β-Ga2O3/NSTO Heterojunction.

    Science.gov (United States)

    Guo, Daoyou; Liu, Han; Li, Peigang; Wu, Zhenping; Wang, Shunli; Cui, Can; Li, Chaorong; Tang, Weihua

    2017-01-18

    A solar-blind photodetector based on β-Ga2O3/NSTO (NSTO = Nb:SrTiO3) heterojunctions were fabricated for the first time, and its photoelectric properties were investigated. The device presents a typical positive rectification in the dark, while under 254 nm UV light illumination, it shows a negative rectification, which might be caused by the generation of photoinduced electron-hole pairs in the β-Ga2O3 film layer. With zero bias, that is, zero power consumption, the photodetector shows a fast photoresponse time (decay time τd = 0.07 s) and the ratio Iphoto/Idark ≈ 20 under 254 nm light illumination with a light intensity of 45 μW/cm(2). Such behaviors are attributed to the separation of photogenerated electron-hole pairs driven by the built-in electric field in the depletion region of β-Ga2O3 and the NSTO interface, and the subsequent transport toward corresponding electrodes. The photocurrent increases linearly with increasing the light intensity and applied bias, while the response time decreases with the increase of the light intensity. Under -10 V bias and 45 μW/cm(2) of 254 nm light illumination, the photodetector exhibits a responsivity Rλ of 43.31 A/W and an external quantum efficiency of 2.1 × 10(4) %. The photo-to-electric conversion mechanism in the β-Ga2O3/NSTO heterojunction photodetector is explained in detail by energy band diagrams. The results strongly suggest that a photodetector based on β-Ga2O3 thin-film heterojunction structure can be practically used to detect weak solar-blind signals because of its high photoconductive gain.

  17. Development of Biomimetic Membranes for Near Zero PC Power Plant Emissions

    Energy Technology Data Exchange (ETDEWEB)

    Michael Trachtenberg; Robert Cowan; David Smith; Ira Sider

    2009-07-31

    The first objective of this project was to develop, evaluate and compare two different CO2 separation (capture) systems. The second was to carry the preferred solution to pre-pilot development and testing. To achieve these objectives we undertook several infrastructure enabling elements: (1) development of a preferred catalyst coupled with its immobilization onto a microporous polymer membrane, (2) design and development of a microporous membrane-based, contained liquid membrane permeator and a membrane-based absorber/desorber apparatus, (3) development of a resin-wafer electrodialytic absorber/desorber apparatus, (4) development and demonstration of a pre-treatment process to condition the feed gas stream, (5) and development of computer modeling of the components and of the integrated system. The first technology was an enzyme catalyzed, membrane supported, contained liquid membrane apparatus whose gas capture was pressure/vacuum and temperature driven. A first embodiment was as a permeator, i.e. a combined absorber/desorber in a single housing. The second embodiment was as discrete absorber and desorber units. The second technology was an enzyme catalyzed, ion exchange resin wafer electrodialytically-based separation. For each of these technologies the objective was to design, manufacture, test and demonstrate the apparatus, first in the laboratory and then at pre-pilot scale, and to run it for sufficient time at the pre-pilot scale to demonstrate stability even in the face of upset. Tests would include several ranks of coal, which had been appropriately pre-treated to remove NOx, SOx and particles, to a pre-determined acceptance level, as a basis for demonstrating efficient CO{sub 2} capture. The pre-pilot tests would be run at the Energy and Environmental Research Center (EERC) in North Dakota. A larger scale test (400m{sup 2} test unit) would later be run also at EERC. An economic goal was to compare the cost of CO{sub 2} capture by each of these methods with

  18. Zero phase sequence impedance and tank heating model for three phase three leg core type power transformers coupling magnetic field and electric circuit equations in finite element software

    Energy Technology Data Exchange (ETDEWEB)

    Ngnegueu, T.; Mailhot, M.; Munar, A. [Jeumont Schneider Transformateurs, Lyon (France); Sacotte, M. [France-Transfo. Voie romaine, Mezieres-Les-Metz (France)

    1995-05-01

    In this paper, the authors present a finite element model for the calculation of zero phase sequence reactance for three phase three leg core type power transformers. An axisymmetrical approximation is assumed. A simplified model is used to assess the tank`s hottest spot temperature.

  19. Analysis of the KUCA MEU experiments using the ANL code system

    Energy Technology Data Exchange (ETDEWEB)

    Shiroya, S.; Hayashi, M.; Kanda, K.; Shibata, T.; Woodruff, W.L.; Matos, J.E.

    1982-01-01

    This paper provides some preliminary results on the analysis of the KUCA critical experiments using the ANL code system. Since this system was employed in the earlier neutronics calculations for the KUHFR, it is important to assess its capabilities for the KUHFR. The KUHFR has a unique core configuration which is difficult to model precisely with current diffusion theory codes. This paper also provides some results from a finite-element diffusion code (2D-FEM-KUR), which was developed in a cooperative research program between KURRI and JAERI. This code provides the capability for mockup of a complex core configuration as the KUHFR. Using the same group constants generated by the EPRI-CELL code, the results of the 2D-FEM-KUR code are compared with the finite difference diffusion code (DIF3D(2D) which is mainly employed in this analysis.

  20. Development of An Embedded FPGA-Based Data Acquisition System Dedicated to Zero Power Reactor Noise Experiments

    Directory of Open Access Journals (Sweden)

    Arkani Mohammad

    2014-08-01

    Full Text Available An embedded time interval data acquisition system (DAS is developed for zero power reactor (ZPR noise experiments. The system is capable of measuring the correlation or probability distribution of a random process. The design is totally implemented on a single Field Programmable Gate Array (FPGA. The architecture is tested on different FPGA platforms with different speed grades and hardware resources. Generic experimental values for time resolution and inter-event dead time of the system are 2.22 ns and 6.67 ns respectively. The DAS can record around 48-bit x 790 kS/s utilizing its built-in fast memory. The system can measure very long time intervals due to its 48-bit timing structure design. As the architecture can work on a typical FPGA, this is a low cost experimental tool and needs little time to be established. In addition, revisions are easily possible through its reprogramming capability. The performance of the system is checked and verified experimentally.

  1. Zero-power receiver

    Energy Technology Data Exchange (ETDEWEB)

    Brocato, Robert W.

    2016-10-04

    An unpowered signal receiver and a method for signal reception detects and responds to very weak signals using pyroelectric devices as impedance transformers and/or demodulators. In some embodiments, surface acoustic wave devices (SAW) are also used. Illustrative embodiments include satellite and long distance terrestrial communications applications.

  2. Coordinated Research Program in Pulsed Power Physics.

    Science.gov (United States)

    1984-12-20

    fast transition from the low-imped- for HVDC circuit breakers ," Electric Power Research Institute ance reflex mode ("closed" switch) to the much higher...conventional circuit breakers may help to understand the i-Frrimiton of plasma laver along insulator 2-Plasma cooling processes in this type of opening...commerciallv available circuit pI At A7A breakers for long charging times and a fuse for fast opening has been operated successfully [52], [58]. A t

  3. Computational Research Challenges and Opportunities for the Optimization of Fossil Energy Power Generation System

    Energy Technology Data Exchange (ETDEWEB)

    Zitney, S.E.

    2007-06-01

    Emerging fossil energy power generation systems must operate with unprecedented efficiency and near-zero emissions, while optimizing profitably amid cost fluctuations for raw materials, finished products, and energy. To help address these challenges, the fossil energy industry will have to rely increasingly on the use advanced computational tools for modeling and simulating complex process systems. In this paper, we present the computational research challenges and opportunities for the optimization of fossil energy power generation systems across the plant lifecycle from process synthesis and design to plant operations. We also look beyond the plant gates to discuss research challenges and opportunities for enterprise-wide optimization, including planning, scheduling, and supply chain technologies.

  4. Acceptable noise level (ANL) with Danish and non-semantic speech materials in adult hearing-aid users

    DEFF Research Database (Denmark)

    Olsen, Steen Østergaard; Lantz, Johannes; Nielsen, Lars Holme;

    2012-01-01

    The acceptable noise level (ANL) test is used for quantification of the amount of background noise subjects accept when listening to speech. This study investigates Danish hearing-aid users' ANL performance using Danish and non-semantic speech signals, the repeatability of ANL, and the association...

  5. Acceptable noise level (ANL) with Danish and non-semantic speech materials in adult hearing-aid users

    DEFF Research Database (Denmark)

    Olsen, Steen Østergaard; Lantz, Johannes; Nielsen, Lars Holme;

    2012-01-01

    The acceptable noise level (ANL) test is used for quantification of the amount of background noise subjects accept when listening to speech. This study investigates Danish hearing-aid users' ANL performance using Danish and non-semantic speech signals, the repeatability of ANL, and the associatio...

  6. Research on the stability of nearly zero flattened dispersion of photonic crystal fibers

    Institute of Scientific and Technical Information of China (English)

    HU Jie; WANG Jian

    2008-01-01

    To analyze the stability of nearly zero flattened dispersion,the dispersion deviations for three kinds of PCFs arc calculated when the hole diamcters deviate from their designed values.Numerical resuIts show that around the wavelength of 1.55μm,the dispersion deviations of both the PCF with three-fold symmetry core and the PCF with hexagonal lattice are much less than that of the PCF with different hole diameters in different rings.Therefore.the stabilities of nearly zero flattened dispersion of the first two kinds of PCFs are much better than that of the last one.Considering the confinement loss.the PCF with three-fold symmetry core is preferabk to practical USe.

  7. Research on zero-sum magnetic field integral technology of optical current sensors

    Science.gov (United States)

    Li, Shen-wang; Yu, Wen-bin; Zhang, Guo-qing; Guo, Zhi-zhong; Shen, Yan

    2013-10-01

    An architecture based on the Faraday effect to minimize the crosstalk effect in optical current sensors (OCSs) is proposed. It was demonstrated that the magnetic field integral along a discrete loop can meet Ampere's law under certain conditions, and the mathematical model of zero-sum points was given. Based on it, a zero-sum OCS (ZOCS) was proposed, which consists of several OCSs forming a symmetrical discrete loop. Ideally, the currents that flow outside the ZOCS do not contribute to the measurement of the currents inside it. The experimental results showed that the magnetic crosstalk-induced errors of ZOCS were less than 0.2%, and the influence of external current was reduced one order compared with conventional OCSs.

  8. Survey of ANL organization plans for word processors, personal computers, workstations, and associated software

    Energy Technology Data Exchange (ETDEWEB)

    Fenske, K.R.; Rockwell, V.S.

    1992-08-01

    The Computing and Telecommunications Division (CTD) has compiled this Survey of ANL Organization plans for Word Processors, Personal Computers, Workstations, and Associated Software (ANL/TM, Revision 4) to provide DOE and Argonne with a record of recent growth in the acquisition and use of personal computers, microcomputers, and word processors at ANL. Laboratory planners, service providers, and people involved in office automation may find the Survey useful. It is for internal use only, and any unauthorized use is prohibited. Readers of the Survey should use it as a reference document that (1) documents the plans of each organization for office automation, (2) identifies appropriate planners and other contact people in those organizations and (3) encourages the sharing of this information among those people making plans for organizations and decisions about office automation. The Survey supplements information in both the ANL Statement of Site Strategy for Computing Workstations (ANL/TM 458) and the ANL Site Response for the DOE Information Technology Resources Long-Range Plan (ANL/TM 466).

  9. Survey of ANL organization plans for word processors, personal computers, workstations, and associated software. Revision 4

    Energy Technology Data Exchange (ETDEWEB)

    Fenske, K.R.; Rockwell, V.S.

    1992-08-01

    The Computing and Telecommunications Division (CTD) has compiled this Survey of ANL Organization plans for Word Processors, Personal Computers, Workstations, and Associated Software (ANL/TM, Revision 4) to provide DOE and Argonne with a record of recent growth in the acquisition and use of personal computers, microcomputers, and word processors at ANL. Laboratory planners, service providers, and people involved in office automation may find the Survey useful. It is for internal use only, and any unauthorized use is prohibited. Readers of the Survey should use it as a reference document that (1) documents the plans of each organization for office automation, (2) identifies appropriate planners and other contact people in those organizations and (3) encourages the sharing of this information among those people making plans for organizations and decisions about office automation. The Survey supplements information in both the ANL Statement of Site Strategy for Computing Workstations (ANL/TM 458) and the ANL Site Response for the DOE Information Technology Resources Long-Range Plan (ANL/TM 466).

  10. Reanalysis of the Gas-cooled fast reactor experiments at the zero power facility Proteus – Spectral indices

    Directory of Open Access Journals (Sweden)

    Girardin G.

    2013-03-01

    Full Text Available PROTEUS is a zero power reactor at the Paul Scherrer Institute which has been employed during the 1970’s to study experimentally the physics of the gas-cooled fast reactor. Reaction rate distributions, flux spectrum and reactivity effects have been measured in several configurations featuring PuO2/UO2 fuel, absorbers, large iron shields, and thorium oxide and thorium metal fuel either distributed quasihomogeneously in the reference PuO2/UO2 lattice or introduced in the form of radial and axial blanket zones. This papers focus on the spectral indices – including fission and capture in 232Th and 237Np - measured in the reference PuO2/UO2 lattices and their predictions with an MCNPX model specially developed for the PROTEUS-GCFR core. Predictions were obtained with JEFF-3.1 and -3.11, ENDF/B-VII.0 and VII.1, and JENDL-3.3 and -4.0. A general good agreement was demonstrated. The ratio of 232Th fission to 239Pu fission, however, was under-predicted by 8.7±2.1% and 6.5±2.1% using ENDF/B-VII.0 and VII.1, respectively. Finally, the capture rates in 237Np tended to be underpredicted by the JEFF and JENDL libraries, although the new cross section in JEFF-3.1.1 slightly improved the 237Np capture to 239Pu fission results (3.4±2.4%.

  11. Zero effluent; Efluente zero

    Energy Technology Data Exchange (ETDEWEB)

    Monteiro, Silvio Rogerio; Santos, Angelo Francisco dos [Liquigas Distribuidora S.A., Sao Paulo, SP (Brazil)

    2008-07-01

    A scenery of water shortage and the search for profitability improvement obligate the companies to exercise their creativity and to adopt alternative methods to the conventional ones to preserve the environmental resources. The 'Effluent Zero' project comes from a paradigms changing that the environmental preservation is a necessary cost. It brings a new analysis approach of this problem with the purpose to adapt the investments and operational costs with the effluents treatment to the demands of the productive processes. In Liquigas, the project brought significant results; made a potential reduction of nearly 90% in the investments of the effluents treatment systems. That means nearly 13% in reduction in the total investments in modernization and upgrade of the existents companies installations and of 1,6% in the total operational costs of the Company. Further more, it has contributed for a reduction of until 43% of the water consumption in the bottling process of the Liquefied Petroleum Gas (LPG). This way, the project resulted in effective actions of environmental protection with relevant economic benefits. (author)

  12. Does the acceptable noise level (ANL) predict hearing-aid use?

    DEFF Research Database (Denmark)

    Olsen, Steen Østergaard; Brännström, K Jonas

    2014-01-01

    be obtained. DESIGN: Relevant literature regarding the ANL was found on Medline, Embase, and Google Scholar. Additional information was found as references in the included papers and through personal contacts, for instance when attending audiology conferences. STUDY SAMPLE: Forty-five papers published in peer...... reviewed journals as well as a number of papers from trade journals, posters and oral presentations from audiology conventions. CONCLUSIONS: An inherent acceptance of noise in the presence of speech may exist, but no method for precise measurement of ANL is available. The ANL model for prediction of HA use...

  13. Research on zero-point correction technique of gas detector%瓦斯探测器零点校正技术的研究

    Institute of Scientific and Technical Information of China (English)

    于春雨; 潘春鹤; 于晓霞; 张光臻

    2012-01-01

    Aiming at the problems such as large drift, high costs and short maintenance intervals of the extensively used gas detectors at the current stage, the timing automatic zero-point correction approach based on the thermostatic control circuit is presented. This approach uses the catalytic combustion gas sensor as targets, adopts the thermostatic control circuit to provide power for sensors, takes the theoretical analysis of zero drift and large quantities of experimental research as the basis and solves the problem of zero stability of this type of detectors which had not been solved for a long time. It employs the analog electronic switch to match resistance network to realize digital potentiometer design and saves costs. The experimental results demonstrate that the residual deviation of the thermostatic control circuit after zero correction reduces one order of magnitude than the output value without correction and provide technical support for the design of gas detectors which have the function of automatic timing zero setting.%针对目前广泛使用的瓦斯探测器漂移大、成本高、维护周期短等问题,提出了基于恒温控制电路的瓦斯探测器的定时自动零点校正方法.该方法以催化燃烧式气体传感器为对象,采用恒温控制电路为传感器供电,以零点漂移的理论分析和大量实验研究工作为依据,解决了该类探测器长期未能解决的零点稳定性问题.采用模拟电子开关配合电阻网络实现数字电位器设计,节约了成本.实验结果表明:采用恒温控制电路的零点校正后的残留偏差比未经校正的输出值减少了近1个数量级,为设计具有自动定时凋零功能的瓦斯探测器提供了技术支持.

  14. Power Law or Logarithmic Law?—A data Analysis for Zero Pressure Gradient Turbulent Boundary Layers with Low Reδs

    Institute of Scientific and Technical Information of China (English)

    MatthiasBuschmann

    2000-01-01

    The paper presents an analysis of two-dimensional zero pressure gradient(ZPG) turbulent boundary layers(TBL) with regard to the application of power laws,only TBL with low Reynolds number 300power law of the form u+=Cpow*yα,This power law region is not a priori identical with the overlap region.An algorithm for the determination of the wall skin friction using the power law is proposed.The method was applied with good result to ZPG TBL and to adverse pressure gradient(APG) TBL.To brdge the gap between the wall and the power law region an approach for the turbulent viscosity is suggested.

  15. ANL statement of site strategy for computing workstations

    Energy Technology Data Exchange (ETDEWEB)

    Fenske, K.R. (ed.); Boxberger, L.M.; Amiot, L.W.; Bretscher, M.E.; Engert, D.E.; Moszur, F.M.; Mueller, C.J.; O' Brien, D.E.; Schlesselman, C.G.; Troyer, L.J.

    1991-11-01

    This Statement of Site Strategy describes the procedure at Argonne National Laboratory for defining, acquiring, using, and evaluating scientific and office workstations and related equipment and software in accord with DOE Order 1360.1A (5-30-85), and Laboratory policy. It is Laboratory policy to promote the installation and use of computing workstations to improve productivity and communications for both programmatic and support personnel, to ensure that computing workstations acquisitions meet the expressed need in a cost-effective manner, and to ensure that acquisitions of computing workstations are in accord with Laboratory and DOE policies. The overall computing site strategy at ANL is to develop a hierarchy of integrated computing system resources to address the current and future computing needs of the laboratory. The major system components of this hierarchical strategy are: Supercomputers, Parallel computers, Centralized general purpose computers, Distributed multipurpose minicomputers, and Computing workstations and office automation support systems. Computing workstations include personal computers, scientific and engineering workstations, computer terminals, microcomputers, word processing and office automation electronic workstations, and associated software and peripheral devices costing less than $25,000 per item.

  16. 78 FR 29159 - Electric Power Research Institute; Seismic Evaluation Guidance

    Science.gov (United States)

    2013-05-17

    ... From the Federal Register Online via the Government Publishing Office NUCLEAR REGULATORY COMMISSION Electric Power Research Institute; Seismic Evaluation Guidance AGENCY: Nuclear Regulatory... issuing an endorsement letter of Electric Power Research Institute (EPRI) Report, ``Seismic...

  17. Survey of ANL organization plans for word processors, personal computers, workstations, and associated software. Revision 3

    Energy Technology Data Exchange (ETDEWEB)

    Fenske, K.R.

    1991-11-01

    The Computing and Telecommunications Division (CTD) has compiled this Survey of ANL Organization Plans for Word Processors, Personal Computers, Workstations, and Associated Software to provide DOE and Argonne with a record of recent growth in the acquisition and use of personal computers, microcomputers, and word processors at ANL. Laboratory planners, service providers, and people involved in office automation may find the Survey useful. It is for internal use only, and any unauthorized use is prohibited. Readers of the Survey should use it as a reference that documents the plans of each organization for office automation, identifies appropriate planners and other contact people in those organizations, and encourages the sharing of this information among those people making plans for organizations and decisions about office automation. The Survey supplements information in both the ANL Statement of Site Strategy for Computing Workstations and the ANL Site Response for the DOE Information Technology Resources Long-Range Plan.

  18. Survey of ANL organization plans for word processors, personal computers, workstations, and associated software

    Energy Technology Data Exchange (ETDEWEB)

    Fenske, K.R.

    1991-11-01

    The Computing and Telecommunications Division (CTD) has compiled this Survey of ANL Organization Plans for Word Processors, Personal Computers, Workstations, and Associated Software to provide DOE and Argonne with a record of recent growth in the acquisition and use of personal computers, microcomputers, and word processors at ANL. Laboratory planners, service providers, and people involved in office automation may find the Survey useful. It is for internal use only, and any unauthorized use is prohibited. Readers of the Survey should use it as a reference that documents the plans of each organization for office automation, identifies appropriate planners and other contact people in those organizations, and encourages the sharing of this information among those people making plans for organizations and decisions about office automation. The Survey supplements information in both the ANL Statement of Site Strategy for Computing Workstations and the ANL Site Response for the DOE Information Technology Resources Long-Range Plan.

  19. The Zero Program

    Science.gov (United States)

    Roland, Erling; Midthassel, Unni Vere

    2012-01-01

    Zero is a schoolwide antibullying program developed by the Centre for Behavioural Research at the University of Stavanger, Norway. It is based on three main principles: a zero vision of bullying, collective commitment among all employees at the school using the program, and continuing work. Based on these principles, the program aims to reduce…

  20. Recent Research of Power Electronics and Drives in Hong Kong

    Institute of Scientific and Technical Information of China (English)

    K.W.E.Cheng; N.C.Cheung

    2004-01-01

    The research in Power Electronics and Dives at The Hong Kong Polytechnic University has been undertaking for many years. Recently, a Power Electronics Research Centre (PERC) has been developed that is contributed towards the research anddevelopment in the area. It encompasses the high frequency power supplies, chaos and bifurcation, soft-switching power converters, electrical machines, high precision motion control, traction and traffic control,alternative energy and electrical building services.

  1. Research on Low Power Marine Current Power Generation System

    Directory of Open Access Journals (Sweden)

    Dongkai Peng

    2013-09-01

    Full Text Available This study proposes a simple topological structure and power control method for a small scale stand alone marine current system, in which a diode rectifier, DC/DC boost converter for the maximum power control, battery as a storage element and a single phase inverter to link with load. The study establishes the steady-state mathematical model of marine current power generation system and derives the formula between the maximum power point and dc battery voltage. Then use the measurements of DC voltage and DC current to obtain Maximum Power Point Tracking (MPPT by controlling the duty cycle of the boost converter switch in order to simplify the system structure and the control strategies. In this case, the hill climbing searching algorithm is employed to get maximum power point and the double closed loops control strategy is used to improve the dynamic and static performance of single phase inverter. The simulation model is developed in MATLAB/Simulink. And the control method is executed in dSPACE1104 real-time platform. The simulation and experimental results demonstrate the feasibility and validity of the proposed control strategies.

  2. Decoherence at absolute zero

    OpenAIRE

    Sinha, Supurna

    2005-01-01

    We present an analytical study of the loss of quantum coherence at absolute zero. Our model consists of a harmonic oscillator coupled to an environment of harmonic oscillators at absolute zero. We find that for an Ohmic bath, the offdiagonal elements of the density matrix in the position representation decay as a power law in time at late times. This slow loss of coherence in the quantum domain is qualitatively different from the exponential decay observed in studies of high temperature envir...

  3. DC-DC power converter research for Orbiter/Station power exchange

    Science.gov (United States)

    Ehsani, M.

    1993-01-01

    This project was to produce innovative DC-DC power converter concepts which are appropriate for the power exchange between the Orbiter and the Space Station Freedom (SSF). The new converters must interface three regulated power buses on SSF, which are at different voltages, with three fuel cell power buses on the Orbiter which can be at different voltages and should be tracked independently. Power exchange is to be bi-directional between the SSF and the Orbiter. The new converters must satisfy the above operational requirements with better weight, volume, efficiency, and reliability than is available from the present conventional technology. Two families of zero current DC-DC converters were developed and successfully adapted to this application. Most of the converters developed are new and are presented.

  4. Analysis of Nigeria research reactor-1 thermal power calibration methods

    Energy Technology Data Exchange (ETDEWEB)

    Agbo, Sunday Arome; Ahmed, Yusuf Aminu; Ewa, Ita Okon; Jibrin, Yahaya [Ahmadu Bello University, Zaria (Nigeria)

    2016-06-15

    This paper analyzes the accuracy of the methods used in calibrating the thermal power of Nigeria Research Reactor-1 (NIRR-1), a low-power miniature neutron source reactor located at the Centre for Energy Research and Training, Ahmadu Bello University, Zaria, Nigeria. The calibration was performed at three different power levels: low power (3.6 kW), half power (15 kW), and full power (30 kW). Two methods were used in the calibration, namely, slope and heat balance methods. The thermal power obtained by the heat balance method at low power, half power, and full power was 3.7 ± 0.2 kW, 15.2 ± 1.2 kW, and 30.7 ± 2.5 kW, respectively. The thermal power obtained by the slope method at half power and full power was 15.8 ± 0.7 kW and 30.2 ± 1.5 kW, respectively. It was observed that the slope method is more accurate with deviations of 4% and 5% for calibrations at half and full power, respectively, although the linear fit (slope method) on average temperature-rising rates during the thermal power calibration procedure at low power (3.6 kW) is not fitting. As such, the slope method of power calibration is not suitable at lower power for NIRR-1.

  5. Practical superconductor development for electrical power applications quarterly report for the period ending September 30, 2001

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-11-09

    This is a multiyear experimental research program that focuses on improving relevant material properties of high-T{sub c} superconductors (HTSs) and developing fabrication methods that can be transferred to industry for production of commercial conductors. A key element of this Argonne National Laboratory (ANL) program is the development of teaming relationships with industrial partners in the areas of conductor development and prototype electric power system product demonstration.

  6. Power Law Behavior of the Zero Bias Tunneling Conductance: the New Evidence for d-Wave Symmetry

    Institute of Scientific and Technical Information of China (English)

    LI Shao-Xiong; TAO Hong-Jie; XUAN Yi; ZHAO Bai-Ru; ZHAO Zhong-Xian

    2000-01-01

    We report temperature-dependent behavior of the zero bias tunneling conductance (ZBTC), derived from tun neling spectroscopies on as-grown Bi2Sr2CaCu2O8+5 (Bi2212) single crystals taken with evaporated Zn and Pb planar junctions. At Tc the measured ZBTC shows a kink which gives an in situ measure of the superconducting transition temperature (Tc). Below Tc, the T2 dependence of the ZBTC has been observed repeatedly as a new evidence of the d-wave symmetry in Bi2212.

  7. Genes involved in the astrocyte-neuron lactate shuttle (ANLS) are specifcally regulated in cortical astrocytes following sleep deprivation in mice

    KAUST Repository

    Petit, Jean Marie

    2013-10-01

    Study Objectives: There is growing evidence indicating that in order to meet the neuronal energy demands, astrocytes provide lactate as an energy substrate for neurons through a mechanism called "astrocyte-neuron lactate shuttle" (ANLS). Since neuronal activity changes dramatically during vigilance states, we hypothesized that the ANLS may be regulated during the sleep-wake cycle. To test this hypothesis we investigated the expression of genes associated with the ANLS specifcally in astrocytes following sleep deprivation. Astrocytes were purifed by fuorescence-activated cell sorting from transgenic mice expressing the green fuorescent protein (GFP) under the control of the human astrocytic GFAP-promoter. Design: 6-hour instrumental sleep deprivation (TSD). Setting: Animal sleep research laboratory. Participants: Young (P23-P27) FVB/N-Tg (GFAP-GFP) 14Mes/J (Tg) mice of both sexes and 7-8 week male Tg and FVB/Nj mice. Interventions: Basal sleep recordings and sleep deprivation achieved using a modifed cage where animals were gently forced to move. Measurements and Results: Since Tg and FVB/Nj mice displayed a similar sleep-wake pattern, we performed a TSD in young Tg mice. Total RNA was extracted from the GFP-positive and GFP-negative cells sorted from cerebral cortex. Quantitative RT-PCR analysis showed that levels of Glut1, a-2-Na/K pump, Glt1, and Ldha mRNAs were signifcantly increased following TSD in GFP-positive cells. In GFP-negative cells, a tendency to increase, although not signifcant, was observed for Ldha, Mct2, and α-3-Na/K pump mRNAs. Conclusions: This study shows that TSD induces the expression of genes associated with ANLS specifcally in astrocytes, underlying the important role of astrocytes in the maintenance of the neuro-metabolic coupling across the sleep-wake cycle.

  8. DANBIO-powerful research database and electronic patient record

    DEFF Research Database (Denmark)

    Hetland, Merete Lund

    2011-01-01

    The nationwide DANBIO registry has been designed to capture operational clinical data as part of routine clinical care. At the same time, it provides a powerful research database. This article reviews the DANBIO registry with focus on problems and solutions of design, funding and linkage, provides...... as an electronic patient 'chronicle' in routine care, and at the same time provides a powerful research database....

  9. Research on the Wind Power Penetration Limit in Power System

    Directory of Open Access Journals (Sweden)

    Yang Zhang

    2013-08-01

    Full Text Available An approach to calculate the wind farm penetration capacity based on chance constrained programming combining with transient check was presented. A novel model for programming penetration of wind farm under indeterminacy operating mode was presented. Constraint condition consisted of conventional generator output limits, system spinning reserve, transmission lines capability, nodal voltage, system frequency etc, and genetic algorithm based on Monte Carlo simulating was used to solve the problem, and the actual sample system verified the feasibility of the model and method. Results for the application of this approach revealed the influencing factors of penetration of wind farm consisted of the parallel node voltage, the output variation range of wind generating set and mean wind speed etc. The research results have important practical significance, which can guide the actual wind farms in the planning and operation analysis of reality wind farm.  

  10. Absolute Zero.

    Science.gov (United States)

    Jones, Rebecca

    1997-01-01

    So far the courts have supported most schools' zero-tolerance policies--even those banning toy weapons, over-the-counter drugs, and unseemly conduct. However, wide-ranging get-tough policies can draw criticism. Policy experts advise school boards to ask the community, decide what people want, allow some wiggle room, create an appeals process,…

  11. Verification and Validation of the PLTEMP/ANL Code for Thermal-Hydraulic Analysis of Experimental and Test Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Kalimullah, M. [Argonne National Lab. (ANL), Argonne, IL (United States); Olson, Arne P. [Argonne National Lab. (ANL), Argonne, IL (United States); Feldman, E. E. [Argonne National Lab. (ANL), Argonne, IL (United States); Hanan, N. [Argonne National Lab. (ANL), Argonne, IL (United States); Dionne, B. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2015-04-07

    The document compiles in a single volume several verification and validation works done for the PLTEMP/ANL code during the years of its development and improvement. Some works that are available in the open literature are simply referenced at the outset, and are not included in the document. PLTEMP has been used in conversion safety analysis reports of several US and foreign research reactors that have been licensed and converted. A list of such reactors is given. Each chapter of the document deals with the verification or validation of a specific model. The model verification is usually done by comparing the code with hand calculation, Microsoft spreadsheet calculation, or Mathematica calculation. The model validation is done by comparing the code with experimental data or a more validated code like the RELAP5 code.

  12. Research on unit commitment with large-scale wind power connected power system

    Science.gov (United States)

    Jiao, Ran; Zhang, Baoqun; Chi, Zhongjun; Gong, Cheng; Ma, Longfei; Yang, Bing

    2017-01-01

    Large-scale integration of wind power generators into power grid brings severe challenges to power system economic dispatch due to its stochastic volatility. Unit commitment including wind farm is analyzed from the two parts of modeling and solving methods. The structures and characteristics can be summarized after classification has been done according to different objective function and constraints. Finally, the issues to be solved and possible directions of research and development in the future are discussed, which can adapt to the requirements of the electricity market, energy-saving power generation dispatching and smart grid, even providing reference for research and practice of researchers and workers in this field.

  13. Experimental Research on Microscopic Indicators of Temperature's Returning-to-Zero in Deformation of Calcite and Discussions of Correlation Problem

    Institute of Scientific and Technical Information of China (English)

    Yao Daquan; Zhai Hongtao

    2005-01-01

    In order to determine the degree of returning-to-zero of temperatures of deformed calcite, a series of rock-breaking experiments were designed to test calcite-rich limestone samples under fixed confining pressures and different temperatures. The consolidated deformed samples in their initial state were observed under a microscope and the microscopic indicators in different zero-returning states were put forward, thus providing a microscopic foundation for evaluation of reliability of dating values of deformation in calcite. At last, the correction of dating values of deformation for samples whose temperature has not yet returned to zero is discussed.

  14. Permanent Closure of MFC Biodiesel Underground Storage Tank 99ANL00013

    Energy Technology Data Exchange (ETDEWEB)

    Kerry L. Nisson

    2012-10-01

    This closure package documents the site assessment and permanent closure of the Materials and Fuels Complex biodiesel underground storage tank 99ANL00013 in accordance with the regulatory requirements established in 40 CFR 280.71, “Technical Standards and Corrective Action Requirements for Owners and Operators of Underground Storage Tanks: Out-of-Service UST Systems and Closure.”

  15. Caught up in power: Exploring discursive frictions in community research

    Directory of Open Access Journals (Sweden)

    Cindy Hanson

    2016-09-01

    Full Text Available This article outlines the debate around the emancipatory claims of community-based research (CBR and identifies discursive frictions as a pivotal point upon which much of CBR practice revolves. Using a Foucauldian theoretical lens, we suggest that CBR is neither inherently emancipatory nor repressive, but that research outcomes are more often a product of power asymmetries in CBR relationships. To illustrate how power asymmetries in research relationships produce discursive frictions, several studies from our work and the literature are presented. The article provides examples of CBR relationships between the researcher and community members and relationships within the community to illustrate how power asymmetries and discursive frictions in these relationships dynamically influence research outcomes and thus alert researchers to the need to address power asymmetries not just before initiating CBR projects, but during CBR projects as well. We interrogate how power asymmetries and discursive frictions operate and are constructed in CBR in an attempt to highlight how research might be conducted more effectively and ethically. Finally, we indicate that some of the tensions and challenges associated with CBR might be ameliorated by the use of participatory facilitation methodologies, such as photo-voice and story circle discussion groups, that draw attention to power asymmetries and purposefully use more creative participatory tools to restructure power relationships and ultimately address the inequities that exist in the research process. Because CBR is continually caught up in power dynamics, we hope that highlighting some examples might offer an opportunity for increased dialogue and critical reflection on its claims of empowerment and emancipation. Keywords: discursive friction, Foucault, participatory methodologies, power asymmetries, research relationships, emancipatory research

  16. A plan for administrative computing at ANL FY1991 through FY1993

    Energy Technology Data Exchange (ETDEWEB)

    Caruthers, L.E. (ed.); O' Brien, D.E.; Bretscher, M.E.; Hischier, R.C.; Moore, N.J.; Slade, R.G.

    1990-10-01

    In July of 1988, Argonne National Laboratory management approved the restructuring of Computing Services into the Computing and Telecommunications Division, part of the Physical Research area of the Laboratory. One major area of the Computing and Telecommunications Division is Management Information Systems (MIS). A significant aspect of Management Information Systems' work is the development of proposals for new and enhanced administrative computing systems based on an analysis of informational needs. This document represent the outcome of the planning process for FY1991 through FY1993. The introduction of the FY1991 through FY1993 Long-Range Plan assesses the state of administrative computing at ANL and the implications of FY1991 funding recommendations. It includes a history of MIS planning for administrative data processing. This document discusses the strategy and goals which are an important part of administrative data processing plans for the Laboratory. It also describes the management guidelines established by the Administrative Data Processing Oversight Committee for the proposal and implementation of administrative computing systems. Summaries of the proposals for new or enhanced administrative computing systems presented by individual divisions or departments with assistance of Management Information Systems, to the Administrative Data Processing Oversight Committee are given. The detailed tables in this paper give information on how much the resources to develop and implement a given systems will cost its users. The tables include development costs, computing/operations costs, software and hardware costs, and efforts costs. They include both systems funded by Laboratory General Expense and systems funded by the users themselves.

  17. Research on battery array based on solar power

    Science.gov (United States)

    Li, Junhong

    2017-03-01

    Almost all of the energy of solar power supply system comes from solar energy, which is a kind of pollution-free green energy, using independent photovoltaic system as base station power supply. In this paper, taking the solar power system as the research object, we made MATLAB simulation analysis of the independent solar photovoltaic system battery array. The simulation results showed that the output voltage and the output current of the solar array based on solar power system are affected by the illumination intensity and temperature change. In addition, it also showed that at any temperature and illumination intensity, there will a largest output power.

  18. Ultralight Solar Powered Hybrid Research Drone

    CERN Document Server

    Singer, Csaba

    2013-01-01

    A planetary research drone is proposed, which is capable for vertical takeoff and landing. A hybrid flight concept utilizing static lift enables the exploration over ground. The static lift is achieved with a lighter than CO2 gas like air, He or H2.

  19. Research on hydraulic-powered roof supports test problems

    Institute of Scientific and Technical Information of China (English)

    SUN Hong-bo; JIANG Jin-qiu; MA Qiang

    2011-01-01

    The load-bearing characters of hydraulic-powered roof support with dual telescopic legs were analyzed. With a specific type hydraulic-powered roof support with dual telescopic legs for research object, the inside load test problems in factories was analyzed, and the correct test methods were given, which can enhance the test efficiency and make the factories away from the error design of hydraulic-powered roof supports and legs.

  20. Women and Communicative Power: Theory, Research, and Practice.

    Science.gov (United States)

    Valentine, Carol Ann; Hoar, Nancy, Ed.

    A collection of essays that explores the links among women and communicative power from a variety of perspectives, this monograph focuses on issue analysis and suggestions for future research. The articles and their authors are as follows (1) "Women and Communicative Power: Introduction" (Carol Ann Valentine); (2) "Genderlect, Powerlect, and…

  1. Coordinated Research Program in Pulsed Power Physics.

    Science.gov (United States)

    1987-02-16

    Insulated High Current Ion Source" November 21, 1985 Chemical and Nuclear Engineering University of New Mexico Albuquerque, NM 14. Hriar S. Cabayan...hon tachment rate co efficients." %; in ri. 1 2]. he swtch hambr isAlong with these considerations, ,.L filled with a gas of pressures of I several...nergative differentia. d) Permnent Address Mission Research conductivity [(’ 4] Sur?, a charecipristi 1s Corporation. Albuquerque he Mexico USA

  2. Facility for a Low Power Research Reactor

    Energy Technology Data Exchange (ETDEWEB)

    Chalker, R. G.

    1949-09-14

    Preliminary investigation indicates that a reactor facility with ample research provisions for use by University or other interested groups, featuring safety in design, can be economically constructed in the Los Angeles area. The complete installation, including an underground gas-tight reactor building, with associated storage and experiment assembly building, administration offices, two general laboratory buildings, hot latoratory and lodge, can be constructed for approxinately $1,500,000. This does not include the cost of the reactor itself or of its auxiliary equipment,

  3. Qualitative health psychology research: diversity, power, and impact.

    Science.gov (United States)

    Gough, Brendan; Deatrick, Janet A

    2015-04-01

    This special issue showcases a range of qualitative research projects conducted by health psychologists with a view to promoting greater uptake and development of qualitative research methods in the field. It is timely because qualitative methods have become prominent across psychology and health research and because major health research funders are now inviting qualitative research to help give voice to patient experiences. As a whole, the papers demonstrate the diversity, power, and impact of qualitative research conducted in health-related settings and show how traditional health psychology methods and concepts can be enriched in the process.

  4. JUPITER-II Program: ANL analysis of ZPPR-13A and ZPPR-13B

    Energy Technology Data Exchange (ETDEWEB)

    Collins, P.J.; Brumbach, S.B. (comps.)

    1984-08-09

    The ZPPR-13 experiments provide basic physics data for radial-heterogeneous LMFBR cores of approximately 700 MWe size. Assemblies ZPPR-13A, ZPPR-13B and ZPPR-13C comprised the JUPITER-II cooperative program between US-DOE and PNC of Japan. The measurements were made between August 1982 and April 1984. This report describes in detail the results of the ANL analyses of phases 13A and 13B/1 and includes preliminary results for the later assemblies of phase 13B. The data were compiled primarily for discussions at the Third Jupiter Analysis Meeting to be held at ANL-West between September 11th and 14th, 1984.

  5. Anläggningsmodellering i AutoCAD Civil 3D

    OpenAIRE

    Rautio, Nils

    2013-01-01

    Sammanfattning Examensarbetets syfte är att ge en övergripande bild om vad BIM egentligen är och hur arbetsmetoden ska kunna påverka byggprocessen positivt. Rapporten fokuserar på anläggningsbranschen och då främst från en projektörs perspektiv. Ett projekteringsexempel visar även på hur en anläggningsmodell kan skapas med hjälp av en programvara som stödjer arbetsflöden i BIM. BIM kan utläsas Building Information Model och avser då den eller de modeller som utgör en digital objektbaserad rep...

  6. Design study of a fast spectrum zero-power reactor dedicated to source driven sub-critical experiments

    Energy Technology Data Exchange (ETDEWEB)

    Mercatali, L.; Serikov, A. [Forschungszentrum Karlsruhe, Institute for Neutron Physics and Reactor Technology, P.O. Box 3640, 76021 Karlsruhe (Germany); Baeten, P.; Uyttenhove, W. [SCK-CEN, Boeretang 200, B-2400 Mol (Belgium); Lafuente, A. [Univerisdad Politecnica de Madrid, 28006 Madrid (Spain); Teles, P. [Instituto Tecnologico e Nuclear, EN 10, 2680-953 Sacavem (Portugal)

    2010-09-15

    In the framework of the European P and T program (IFP6-EUROTRANS), the Generation of Uninterrupted Intense NEutrons pulses at the lead VEnus REactor (GUINEVERE) project consists of an Accelerator Driven System (ADS) that is composed by a fast lead simulated-cooled reactor operated in sub-critical conditions, coupled with an updated version of the GENEPI neutron generator previously used for the MUSE experiments. The GUINEVERE facility aims at developing and improving different techniques for the reactivity monitoring of sub-critical ADS's. As such, the GUINEVERE project will comprise a series of major experiments that will be performed in the near future. The GUINEVERE facility will be located at the VENUS light water moderated research reactor at the SCK-CEN site of Mol (Belgium), which needs to be modified in order to accommodate a completely different and new type of core. A series of constraints were taken into account in the technical design of the GUINEVERE core, in order to properly conjugate the technical feasibility of this facility and the necessity to comply with the envisioned experimental program and its associated scientific outcome. The complete design study of the GUINEVERE core is the subject of this paper. The final design of the fuel assemblies, safety and control rods is provided. Also, the critical core configuration, to be used as reference for absolute reactivity measurements, is presented along with its associated reactor physics parameters, calculated by means of Monte Carlo methodologies. Finally, for licensing purposes, the GUINEVERE facility must satisfy the required nuclear safety criteria of the Belgian safety authorities, and in this paper, an overview of the safety analysis that has been performed with regard to the core physics, thermal assessment and shielding issues is also provided. (author)

  7. Common Directions in Caucasian Chalk Circle and Keşanlı Ali Destanı

    OpenAIRE

    ODACI, Serdar

    2016-01-01

    Epic Theater founded by Bertolt Brecht influenced world literaturein the half of 20th century. Epic theater is against to Aristothalesian Theater.Naturally Brehct's plays were translated to Turkish and were presented. SuchTurkish writers as Haldun Taner and Vasıf Öngeren wrote play according toepic theater concept. In this paper common aspects in Keşanlı Ali Destanıand Caucasian Chalk Circle are examined.

  8. "Common Directions in Caucasian Chalk Circle and Keşanlı Ali Destanı"

    OpenAIRE

    ODACI, Serdar

    2010-01-01

    Epic Theater founded by Bertolt Brecht influenced world literature in the half of 20th century. Epic theater is against to Aristothalesian Theater. Naturally Brehct's plays were translated to Turkish and were presented. Such Turkish writers as Haldun Taner and Vasıf Öngeren wrote play according to epic theater concept. In this paper common aspects in Keşanlı Ali Destanı and Caucasian Chalk Circle are examined.

  9. A Study on the Epic of Keşanlı Ali by Haldun Taner

    OpenAIRE

    GARİPER, Cafer

    2014-01-01

    Haldun Taner is a playwright who introduced new directions, approaches and thematic views to Turkish theather. With his work Keşanlı Ali Destanı, he brought in a new successful example of epic theatre. In this work, he deseribes skillfully the lives of people living in shanty houses and creates new characters. He aslo displays beautifully their ways in daily conversations, behaviour, and their philosophy of life in general.

  10. Light-Quark Baryon Spectroscopy within ANL-Osaka Dynamical Coupled-Channels Approach

    Science.gov (United States)

    Kamano, Hiroyuki

    2016-10-01

    Recent results on the study of light-quark baryons with the ANL-Osaka dynamical coupled-channels (DCC) approach are presented, which contain the N^* and Δ ^* spectroscopy via the analysis of π N and γ N reactions and the Λ ^* and Σ ^* spectroscopy via the analysis of K^- p reactions. A recent application of our DCC approach to neutrino-nucleon reactions in the resonance region is also presented.

  11. ANL site response for the DOE FY1994 information resources management long-range plan

    Energy Technology Data Exchange (ETDEWEB)

    Boxberger, L.M.

    1992-03-01

    Argonne National Laboratory's ANL Site Response for the DOE FY1994 Information Resources Management (IRM) Long-Range Plan (ANL/TM 500) is one of many contributions to the DOE information resources management long-range planning process and, as such, is an integral part of the DOE policy and program planning system. The Laboratory has constructed this response according to instructions in a Call issued in September 1991 by the DOE Office of IRM Policy, Plans and Oversight. As one of a continuing series, this Site Response is an update and extension of the Laboratory's previous submissions. The response contains both narrative and tabular material. It covers an eight-year period consisting of the base year (FY1991), the current year (FY1992), the budget year (FY1993), the plan year (FY1994), and the out years (FY1995-FY1998). This Site Response was compiled by Argonne National Laboratory's Computing and Telecommunications Division (CTD), which has the responsibility to provide leadership in optimizing computing and information services and disseminating computer-related technologies throughout the Laboratory. The Site Response consists of 5 parts: (1) a site overview, describes the ANL mission, overall organization structure, the strategic approach to meet information resource needs, the planning process, major issues and points of contact. (2) a software plan for DOE contractors, Part 2B, Software Plan FMS plan for DOE organizations, (3) computing resources telecommunications, (4) telecommunications, (5) printing and publishing.

  12. ANL site response for the DOE FY1994 information resources management long-range plan

    Energy Technology Data Exchange (ETDEWEB)

    Boxberger, L.M.

    1992-03-01

    Argonne National Laboratory`s ANL Site Response for the DOE FY1994 Information Resources Management (IRM) Long-Range Plan (ANL/TM 500) is one of many contributions to the DOE information resources management long-range planning process and, as such, is an integral part of the DOE policy and program planning system. The Laboratory has constructed this response according to instructions in a Call issued in September 1991 by the DOE Office of IRM Policy, Plans and Oversight. As one of a continuing series, this Site Response is an update and extension of the Laboratory`s previous submissions. The response contains both narrative and tabular material. It covers an eight-year period consisting of the base year (FY1991), the current year (FY1992), the budget year (FY1993), the plan year (FY1994), and the out years (FY1995-FY1998). This Site Response was compiled by Argonne National Laboratory`s Computing and Telecommunications Division (CTD), which has the responsibility to provide leadership in optimizing computing and information services and disseminating computer-related technologies throughout the Laboratory. The Site Response consists of 5 parts: (1) a site overview, describes the ANL mission, overall organization structure, the strategic approach to meet information resource needs, the planning process, major issues and points of contact. (2) a software plan for DOE contractors, Part 2B, ``Software Plan FMS plan for DOE organizations, (3) computing resources telecommunications, (4) telecommunications, (5) printing and publishing.

  13. Nuclear Power Plant Operator Reliability Research Based on Fuzzy Math

    Directory of Open Access Journals (Sweden)

    Fang Xiang

    2011-01-01

    Full Text Available This paper makes use of the concept and theory of fuzzy number in fuzzy mathematics, to research for the response time of operator in accident of Chinese nuclear power plant. Through the quantitative analysis for the performance shape factors (PSFs which influence the response time of operators, the formula of the operator response time is obtained based on the possibilistic fuzzy linear regression model which is used for the first time in this kind of research. The research result shows that the correct research method can be achieved through the analysis of the information from a small sample. This method breaks through the traditional research method and can be used not only for the reference to the safe operation of nuclear power plant, but also in other areas.

  14. Mighty Morphin Power Ranger Play: Research and Reality.

    Science.gov (United States)

    Crosser, Sandra

    1995-01-01

    Explores the question of whether or not Mighty Morphin Power Rangers-type aggressive play is developmentally appropriate for the early childhood classroom. Compares results from research in child development to the reality of television programming, highlighting the relationship between television violence and children's aggressive behavior. (AA)

  15. The research and application of the power big data

    Science.gov (United States)

    Zhang, Suxiang; Zhang, Dong; Zhang, Yaping; Cao, Jinping; Xu, Huiming

    2017-01-01

    Facing the increasing environment crisis, how to improve energy efficiency is the important problem. Power big data is main support tool to realize demand side management and response. With the promotion of smart power consumption, distributed clean energy and electric vehicles etc get wide application; meanwhile, the continuous development of the Internet of things technology, more applications access the endings in the grid power link, which leads to that a large number of electric terminal equipment, new energy access smart grid, and it will produce massive heterogeneous and multi-state electricity data. These data produce the power grid enterprise's precious wealth, as the power big data. How to transform it into valuable knowledge and effective operation becomes an important problem, it needs to interoperate in the smart grid. In this paper, we had researched the various applications of power big data and integrate the cloud computing and big data technology, which include electricity consumption online monitoring, the short-term power load forecasting and the analysis of the energy efficiency. Based on Hadoop, HBase and Hive etc., we realize the ETL and OLAP functions; and we also adopt the parallel computing framework to achieve the power load forecasting algorithms and propose a parallel locally weighted linear regression model; we study on energy efficiency rating model to comprehensive evaluate the level of energy consumption of electricity users, which allows users to understand their real-time energy consumption situation, adjust their electricity behavior to reduce energy consumption, it provides decision-making basis for the user. With an intelligent industrial park as example, this paper complete electricity management. Therefore, in the future, power big data will provide decision-making support tools for energy conservation and emissions reduction.

  16. Effect size, confidence intervals and statistical power in psychological research.

    Directory of Open Access Journals (Sweden)

    Téllez A.

    2015-07-01

    Full Text Available Quantitative psychological research is focused on detecting the occurrence of certain population phenomena by analyzing data from a sample, and statistics is a particularly helpful mathematical tool that is used by researchers to evaluate hypotheses and make decisions to accept or reject such hypotheses. In this paper, the various statistical tools in psychological research are reviewed. The limitations of null hypothesis significance testing (NHST and the advantages of using effect size and its respective confidence intervals are explained, as the latter two measurements can provide important information about the results of a study. These measurements also can facilitate data interpretation and easily detect trivial effects, enabling researchers to make decisions in a more clinically relevant fashion. Moreover, it is recommended to establish an appropriate sample size by calculating the optimum statistical power at the moment that the research is designed. Psychological journal editors are encouraged to follow APA recommendations strictly and ask authors of original research studies to report the effect size, its confidence intervals, statistical power and, when required, any measure of clinical significance. Additionally, we must account for the teaching of statistics at the graduate level. At that level, students do not receive sufficient information concerning the importance of using different types of effect sizes and their confidence intervals according to the different types of research designs; instead, most of the information is focused on the various tools of NHST.

  17. NASA Ames Research Center 60 MW Power Supply Modernization

    Science.gov (United States)

    Choy, Yuen Ching; Ilinets, Boris V.; Miller, Ted; Nagel, Kirsten (Technical Monitor)

    2001-01-01

    The NASA Ames Research Center 60 MW DC Power Supply was built in 1974 to provide controlled DC power for the Thermophysics Facility Arc Jet Laboratory. The Power Supply has gradually losing reliability due to outdated technology and component life limitation. NASA has decided to upgrade the existing rectifier modules with contemporary high-power electronics and control equipment. NASA plans to complete this project in 2001. This project includes a complete replacement of obsolete thyristor stacks in all six rectifier modules and rectifier bridge control system. High power water-cooled thyristors and freewheeling diodes will be used. The rating of each of the six modules will be 4000 A at 5500 V. The control firing angle signal will be sent from the Facility Control System to six modules via fiberoptic cable. The Power Supply control and monitoring system will include a Master PLC in the Facility building and a Slave PLC in each rectifier module. This system will also monitor each thyristor level in each stack and the auxiliary equipment.

  18. Fire Environment Mechanism of Lightning-groundfire for Daxing anling Mountains

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    Ground fire is an igniting phenomenon that is difficult to control and lightning is the main cause of ground fire. The mechanism of lightning-ground fire is very complex. Daxing'anling Mountains forest region is the place that lighting-groundfire occurs more often and regularly. Our study on lightning-groundfire of this zone in 2002 shows: much more soil near the surface and the ground fuel is the matter preconditions of lightning-groundfire, and the weather conditions hasten the occurrence of lightning...

  19. Monolithic solid oxide fuel cell technology advancement for coal-based power generation

    Energy Technology Data Exchange (ETDEWEB)

    1992-04-14

    The program is conducted by a team consisting of AiResearch Los Angeles Division of Allied-Signal Aerospace Company and Argonne National Laboratory (ANL). The objective of the program is to advance materials and fabrication methodologies to develop a monolithic solid oxide fuel cell (MSOFC) system capable of meeting performance, life, and cost goals for coal-based power generation. The program focuses on materials research and development, fabrication process development, cell/stack performance testing and characterization, cost and system analysis, and quality development.

  20. Research on Power Ramp Testing Method for PWR Fuel Rod at Research Reactor

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    In order to develop high performance fuel assembly for domestic nuclear power plant, it is necessary to master some fundamental test technology. So the research on the power ramp testing methods is proposed. A tentative power ramp test for short PWR fuel rod has been conducted at the heavy water research reactor (HWRR) in China Institute of Atomic Energy (CIAE) in May of 2001. The in-pile test rig was placed into the central channel of the reactor . The test rig consists of pressure pipe assembly, thimble, solid neutron absorbing screen and its driving parts, etc.. The test

  1. Materials research in support of nuclear power generation

    Energy Technology Data Exchange (ETDEWEB)

    Jackman, J. [Natural Resources Canada, Ottawa, Ontario (Canada)

    2011-07-01

    This presentation outlines the activities of CANMET-MTL in materials research in support of nuclear power generation. CANMET-MTL is a Government of Canada research laboratory specializing in materials (metals and metal-based materials). Its mandate is to improve the competitive, social and environmental performance of Canadian industries in the area of metals. These include the economic benefits from value-added processing and manufacturing, materials for clean energy production and improved energy efficiency in processing and product end-use.

  2. Reflexively exploring knowledge and power in collaborative research

    DEFF Research Database (Denmark)

    Nordentoft, Helle Merete; Phillips, Louise Jane; Pedersen, Christina Hee

    The proposed workshop will take its starting point in the challenges which collaborative research practices share. The aim of the workshop is to work with, and further develop, a range of critical, reflexive strategies for understanding, analysing and dealing with those challenges. The workshop...... will be designed in order to stimulate dialogue across different analytical perspectives and empirical research. The analytical perspectives on which facilitation will be based are rooted in social constructionist approaches to dialogic communication theory and action research. The challenges of collaborative...... research stem from the methodological, epistemological and ethical problems and dilemmas that are inherent in collaborative knowledge production and communication and which relate to the inexorable workings of knowledge/power. The problems and dilemmas arise in the meeting between participants’ multiple...

  3. Reflexively exploring knowledge and power in collaborative research

    DEFF Research Database (Denmark)

    Olesen, Birgitte Ravn; Pedersen, Chistina Hee; Frølunde, Lisbeth

    will be designed in order to stimulate dialogue across different analytical perspectives and empirical research. The analytical perspectives on which facilitation will be based are rooted in social constructionist approaches to dialogic communication theory and action research. The challenges of collaborative......The proposed workshop will take its starting point in the challenges which collaborative research practices share. The aim of the workshop is to work with, and further develop, a range of critical, reflexive strategies for understanding, analysing and dealing with those challenges. The workshop...... research stem from the methodological, epistemological and ethical problems and dilemmas that are inherent in collaborative knowledge production and communication and which relate to the inexorable workings of knowledge/power. The problems and dilemmas arise in the meeting between participants’ multiple...

  4. Spin zero

    CERN Multimedia

    James Gillies

    2011-01-01

    This week saw the increasingly familiar sight of hordes of journalists descending on CERN to hear the latest news from the LHC. There were 66 of them to be precise, many of whom announced to us they planned to come for the seminar long before they were invited. It’s a sign of the times that science that used to be conducted in private is now carried out in the public domain. That has the potential to be very good news for science, and for society as a whole, particularly when CERN’s scientists do such a great job of conveying the passion and excitement of their research.   A typical Higgs candidate event in the CMS detector. We live in a science-dominated age, where everyone has to make science-based decisions on a daily basis. Yet at the same time, apathy towards science has been growing while pseudo-science gains ground. For that reason, it’s incumbent upon scientists to push science further up the popular agenda. The fact that the LHC has got the ‘...

  5. Nuclear power and the public: an update of collected survey research on nuclear power

    Energy Technology Data Exchange (ETDEWEB)

    Rankin, W.L.; Melber, B.D.; Overcast, T.D.; Nealey, S.M.

    1981-12-01

    The purpose of this research was to collect, analyze, and summarize all of the nuclear power-related surveys conducted in the United States through June 1981, that we could obtain. The surveys collected were national, statewide, and areawide in scope. Slightly over 100 surveys were collected for an earlier, similar effort carried out in 1977. About 130 new surveys were added to the earlier survey data. Thus, about 230 surveys were screened for inclusion in this report. Because of space limitations, national surveys were used most frequently in this report, followed distantly by state surveys. In drawing our conclusions about public beliefs and attitudes toward nuclear power, we placed most of our confidence in survey questions that were used by national polling firms at several points in time. A summary of the research findings is presented, beginning with general attitudes toward nuclear power, followed by a summary of beliefs and attitudes about nuclear power issues, and ended by a summary of beliefs and attitudes regarding more general energy issues.

  6. Contribution History of Research Institutes to Electric Power Industry in Japan

    Science.gov (United States)

    Taniguchi, Haruhito; Shindo, Takatoshi

    After reorganization of power industry in 1951, power system of Japan was remarkably expanded. To cope with this, R&D in vast area was conducted in the academy, MITI, electric power companies, manufactures, and research institutes. This paper generally describes the technical contents that the three research institutes, namely Electrotechnical Laboratory (ETL), High Voltage Power Laboratory (HVPL), and Central Research Institute of Electric Power Industry (CRIEPI), have contributed to the development of power transmission technology after the war.

  7. Electromagnetic pulse research on electric power systems: Program summary and recommendations. Power Systems Technology Program

    Energy Technology Data Exchange (ETDEWEB)

    Barnes, P.R.; McConnell, B.W.; Van Dyke, J.W. [Oak Ridge National Lab., TN (United States); Tesche, F.M. [Tesche (F.M.), Dallas, TX (United States); Vance, E.F. [Vance (E.F.), Fort Worth, TX (United States)

    1993-01-01

    A single nuclear detonation several hundred kilometers above the central United States will subject much of the nation to a high-altitude electromagnetic pulse (BENT). This pulse consists of an intense steep-front, short-duration transient electromagnetic field, followed by a geomagnetic disturbance with tens of seconds duration. This latter environment is referred to as the magnetohydrodynamic electromagnetic pulse (NMENT). Both the early-time transient and the geomagnetic disturbance could impact the operation of the nation`s power systems. Since 1983, the US Department of Energy has been actively pursuing a research program to assess the potential impacts of one or more BENT events on the nation`s electric energy supply. This report summarizes the results of that program and provides recommendations for enhancing power system reliability under HENT conditions. A nominal HENP environment suitable for assessing geographically large systems was developed during the program and is briefly described in this report. This environment was used to provide a realistic indication of BEMP impacts on electric power systems. It was found that a single high-altitude burst, which could significantly disturb the geomagnetic field, may cause the interconnected power network to break up into utility islands with massive power failures in some areas. However, permanent damage would be isolated, and restoration should be possible within a few hours. Multiple bursts would likely increase the blackout areas, component failures, and restoration time. However, a long-term blackout of many months is unlikely because major power system components, such as transformers, are not likely to be damaged by the nominal HEND environment. Moreover, power system reliability, under both HENT and normal operating conditions, can be enhanced by simple, and often low cost, modifications to current utility practices.

  8. Role of research reactors for nuclear power program in Indonesia

    Energy Technology Data Exchange (ETDEWEB)

    Soentono, S.; Arbie, B. [National Atomic Energy Agency, Batan (Indonesia)

    1994-12-31

    The main objectives of nuclear development program in Indonesia are to master nuclear science and technology, as well as to utilise peaceful uses of nuclear know-how, aiming at stepwisely socioeconomic development. A Triga Mark II, previously of 250 kW, reactor in Bandung has been in operation since 1965 and its design power has been increased to 1000 kW in 1972. Using core grid of the Triga 250 kW, BATAN designed and constructed the Kartini Reactor in Yogyakarta which started its operation in 1979. Both of these Triga reactors have served a wide spectrum of utilisation, such as training of manpower in nuclear engineering as well as radiochemistry, isotope production and beam research activities in solid state physics. In order to support the nuclear power development program in general and to suffice the reactor experiments further, simultaneously meeting the ever increasing demand for radioisotope, the third reactor, a multipurpose reactor of 30 MW called GA. Siwabessy (RSG-GAS) has been in operation since 1987 at Serpong near Jakarta. Each of these reactors has strong cooperation with Universities, namely the Bandung Institute of Technology at Bandung, the Gadjah Mada University at Yogyakarta, and the Indonesia University at Jakarta and has facilitated the man power development required. The role of these reactors, especially the multipurpose GA. Siwabessy reactor, as essential tools in nuclear power program are described including the experience gained during preproject, construction and commissioning, as well as through their operation, maintenance and utilisation.

  9. Wind power forecasting: IEA Wind Task 36 & future research issues

    Science.gov (United States)

    Giebel, G.; Cline, J.; Frank, H.; Shaw, W.; Pinson, P.; Hodge, B.-M.; Kariniotakis, G.; Madsen, J.; Möhrlen, C.

    2016-09-01

    This paper presents the new International Energy Agency Wind Task 36 on Forecasting, and invites to collaborate within the group. Wind power forecasts have been used operatively for over 20 years. Despite this fact, there are still several possibilities to improve the forecasts, both from the weather prediction side and from the usage of the forecasts. The new International Energy Agency (IEA) Task on Forecasting for Wind Energy tries to organise international collaboration, among national meteorological centres with an interest and/or large projects on wind forecast improvements (NOAA, DWD, MetOffice, met.no, DMI,...), operational forecaster and forecast users. The Task is divided in three work packages: Firstly, a collaboration on the improvement of the scientific basis for the wind predictions themselves. This includes numerical weather prediction model physics, but also widely distributed information on accessible datasets. Secondly, we will be aiming at an international pre-standard (an IEA Recommended Practice) on benchmarking and comparing wind power forecasts, including probabilistic forecasts. This WP will also organise benchmarks, in cooperation with the IEA Task WakeBench. Thirdly, we will be engaging end users aiming at dissemination of the best practice in the usage of wind power predictions. As first results, an overview of current issues for research in short-term forecasting of wind power is presented.

  10. Wind power forecasting: IEA Wind Task 36 & future research issues

    DEFF Research Database (Denmark)

    Giebel, Gregor; Cline, J.; Frank, Helmut Paul

    2016-01-01

    This paper presents the new International Energy Agency Wind Task 36 on Forecasting, and invites to collaborate within the group. Wind power forecasts have been used operatively for over 20 years. Despite this fact, there are still several possibilities to improve the forecasts, both from the wea......Bench. Thirdly, we will be engaging end users aiming at dissemination of the best practice in the usage of wind power predictions. As first results, an overview of current issues for research in short-term forecasting of wind power is presented.......This paper presents the new International Energy Agency Wind Task 36 on Forecasting, and invites to collaborate within the group. Wind power forecasts have been used operatively for over 20 years. Despite this fact, there are still several possibilities to improve the forecasts, both from...... the weather prediction side and from the usage of the forecasts. The new International Energy Agency (IEA) Task on Forecasting for Wind Energy tries to organise international collaboration, among national meteorological centres with an interest and/or large projects on wind forecast improvements (NOAA, DWD...

  11. The Trouble with Zero

    Science.gov (United States)

    Lewis, Robert

    2015-01-01

    The history of the number zero is an interesting one. In early times, zero was not used as a number at all, but instead was used as a place holder to indicate the position of hundreds and tens. This article briefly discusses the history of zero and challenges the thinking where divisions using zero are used.

  12. Relationship between zero-pressure-difference point and transporting power in distributed pump heating systems%分布式水泵供热系统零压差点与输送功率的关系

    Institute of Scientific and Technical Information of China (English)

    王芃; 邹平华; 雷翠红

    2011-01-01

    为了研究分布式水泵供热系统的水力工况和运行能耗,提出以零压差点作为该系统的水力标志,利用它与热源之间供、回水管段的总阻力损失分析管网中多个零压差点的分布,同时唯一确定了系统循环水泵的配置和压力分布.利用特定工况下的流量-压头图分析了各种循环水泵配置方案的输送功率,说明了零压差点与热媒输送功率的关系,并指出了系统达到需用功率的条件.通过工程实例的分析,定性讨论了若干典型的循环水泵配置方案.%Puts forward the zero-pressure-difference point to analyse the hydraulic condition and operating energy consumption of the distributed pump heating system. Studies the distribution of zero-pressure-difference points by total resistance loss of water supply and return pipes between heat source and one of zero-pressure-difference points,and determines the configuration of circulating pumps and pressure profile. The transporting power of heat medium is shown on flow-pressure head graph under certain condition,as well as the relationship between the power and zero-pressure-difference points. Puts forward the condition to achieve the required power. With a project case,discusses qualitatively several representative configuration schemes of circulating pumps.

  13. Power

    DEFF Research Database (Denmark)

    Elmholdt, Claus Westergård; Fogsgaard, Morten

    2016-01-01

    In this chapter, we will explore the dynamics of power in processes of creativity, and show its paradoxical nature as both a bridge and a barrier to creativity in organisations. Recent social psychological experimental research (Slighte, de Dreu & Nijstad, 2011) on the relation between power...... and creativity suggests that when managers give people the opportunity to gain power and explicate that there is reason to be more creative, people will show a boost in creative behaviour. Moreover, this process works best in unstable power hierarchies, which implies that power is treated as a negotiable...... and floating source for empowering people in the organisation. We will explore and discuss here the potentials, challenges and pitfalls of power in relation to creativity in the life of organisations today. The aim is to demonstrate that power struggles may be utilised as constructive sources of creativity...

  14. Overview of Variable-Speed Power-Turbine Research

    Science.gov (United States)

    Welch, Gerard E.

    2011-01-01

    The vertical take-off and landing (VTOL) and high-speed cruise capability of the NASA Large Civil Tilt-Rotor (LCTR) notional vehicle is envisaged to enable increased throughput in the national airspace. A key challenge of the LCTR is the requirement to vary the main rotor speeds from 100% at take-off to near 50% at cruise as required to minimize mission fuel burn. The variable-speed power-turbine (VSPT), driving a fixed gear-ratio transmission, provides one approach for effecting this wide speed variation. The key aerodynamic and rotordynamic challenges of the VSPT were described in the FAP Conference presentation. The challenges include maintaining high turbine efficiency at high work factor, wide (60 deg.) of incidence variation in all blade rows due to the speed variation, and operation at low Reynolds numbers (with transitional flow). The PT -shaft of the VSPT must be designed for safe operation in the wide speed range required, and therefore poses challenges associated with rotordynamics. The technical challenges drive research activities underway at NASA. An overview of the NASA SRW VSPT research activities was provided. These activities included conceptual and preliminary aero and mechanical (rotordynamics) design of the VSPT for the LCTR application, experimental and computational research supporting the development of incidence tolerant blading, and steps toward component-level testing of a variable-speed power-turbine of relevance to the LCTR application.

  15. Fundamental Science with Pulsed Power: Research Opportunities and User Meeting.

    Energy Technology Data Exchange (ETDEWEB)

    Mattsson, Thomas Kjell Rene [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Wootton, Alan James [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sinars, Daniel Brian [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Spaulding, Dylan [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Winget, Don [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-10-01

    The fifth Fundamental Science with Pulsed Power: Research Opportunities and User Meeting was held in Albuquerque, NM, July 20-­23, 2014. The purpose of the workshop was to bring together leading scientists in four research areas with active fundamental science research at Sandia’s Z facility: Magnetized Liner Inertial Fusion (MagLIF), Planetary Science, Astrophysics, and Material Science. The workshop was focused on discussing opportunities for high-­impact research using Sandia’s Z machine, a future 100 GPa class facility, and possible topics for growing the academic (off-Z-campus) science relevant to the Z Fundamental Science Program (ZFSP) and related projects in astrophysics, planetary science, MagLIF- relevant magnetized HED science, and materials science. The user meeting was for Z collaborative users to: a) hear about the Z accelerator facility status and plans, b) present the status of their research, and c) be provided with a venue to meet and work as groups. Following presentations by Mark Herrmann and Joel Lash on the fundamental science program on Z and the status of the Z facility where plenary sessions for the four research areas. The third day of the workshop was devoted to breakout sessions in the four research areas. The plenary-­ and breakout sessions were for the four areas organized by Dan Sinars (MagLIF), Dylan Spaulding (Planetary Science), Don Winget and Jim Bailey (Astrophysics), and Thomas Mattsson (Material Science). Concluding the workshop were an outbrief session where the leads presented a summary of the discussions in each working group to the full workshop. A summary of discussions and conclusions from each of the research areas follows and the outbrief slides are included as appendices.

  16. Determination of zero-pressure point location and water pump head in distributed power systems%动力分散系统中零压差点位置及水泵扬程的确定

    Institute of Scientific and Technical Information of China (English)

    焦扬; 符永正

    2011-01-01

    运用水压图分析了零压差点位于不同位置时动力分散系统的水压分布.结果显示,零压差点应位于临界点与热(冷)源之间,才能消除调节阀能耗,从而使系统输配能耗最低;零压差点位于临界点与热(冷)源之间的不同位置时,水泵的配置方案不同,但各水泵的输出功率总和相等.%Using the pressure diagram analyses the pressure distribution of the distributed power system when the zero-pressure point is in different locations. The results show that the zero-pressure point should be at the location between the critical point and heat or cold source, which can cause the transmission energy consumption of the system to be lowest because of eliminating the energy consumption of the regulating valve, and that when the zero-pressure point is in different locations between the critical point and heat or cold source, disposition plans of water pumps are almost different, but total output powers of the pumps are the same.

  17. DANBIO-powerful research database and electronic patient record

    DEFF Research Database (Denmark)

    Hetland, Merete Lund

    2011-01-01

    with RA patients, who were on conventional treatment with DMARDs, the patients who started biological treatment were younger, had longer disease duration, higher disease activity, tried more DMARDs and received more prednisolone. Also, more patients on biological therapy were seropositive and had erosive...... disease. However, the current levels of disease activities and the fraction of patients who had gone into remission in the two groups of patients were very similar. This indicates that clinicians have a common treatment goal for RA patients regardless of treatment. In conclusion, DANBIO serves...... as an electronic patient 'chronicle' in routine care, and at the same time provides a powerful research database....

  18. Zero Energry Travel

    CERN Document Server

    Ahmad, Othman; Chekima, Ali

    2011-01-01

    It is fundamentally possible to travel with zero energy based on Newton Laws of Motion. According to the first law of motion, a body will continue to travel for infinite distance unless it is acted upon by another force. For a body in motion, the force which stops perpetual motion is friction. However, there are many circumstances that friction is zero, for example in space, where there is vacuum. On earth, gravity makes objects to be in constant contact with each other generating friction but technology exists to separate them in the air using powerful magnetic forces. At low speeds, the friction caused by air is minimal but we can create vacuum even on land for high speed travel. Another condition for travelling is for it to stop at its destination. On land, we can recover the kinetic energy back into electrical energy using brushless permanent magnet generators. These generators can also convert electric energy into kinetic energy in order to provide motion. This article reviews technologies that will allo...

  19. Background radiation measurements at high power research reactors

    Energy Technology Data Exchange (ETDEWEB)

    Ashenfelter, J. [Wright Laboratory, Department of Physics, Yale University, New Haven, CT 06520 (United States); Balantekin, B. [Department of Physics, University of Wisconsin, Madison, WI 53706 (United States); Baldenegro, C.X. [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Band, H.R. [Wright Laboratory, Department of Physics, Yale University, New Haven, CT 06520 (United States); Barclay, G. [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Bass, C.D. [Department of Chemistry and Physics, Le Moyne College, Syracuse, NY 13214 (United States); Berish, D. [Department of Physics, Temple University, Philadelphia, PA 19122 (United States); Bowden, N.S., E-mail: nbowden@llnl.gov [Nuclear and Chemical Sciences Division, Lawrence Livermore National Laboratory, Livermore, CA 94550 (United States); Bryan, C.D. [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Cherwinka, J.J. [Physical Sciences Laboratory, University of Wisconsin, Madison, WI 53706 (United States); Chu, R. [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Department of Physics, University of Tennessee, Knoxville, TN 37996 (United States); Classen, T. [Nuclear and Chemical Sciences Division, Lawrence Livermore National Laboratory, Livermore, CA 94550 (United States); Davee, D. [Department of Physics, College of William and Mary, Williamsburg, VA 23187 (United States); Dean, D.; Deichert, G. [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Dolinski, M.J. [Department of Physics, Drexel University, Philadelphia, PA 19104 (United States); Dolph, J. [Physics Department, Brookhaven National Laboratory, Upton, NY 11973 (United States); Dwyer, D.A. [Physics Division, Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States); Fan, S. [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Department of Physics, University of Tennessee, Knoxville, TN 37996 (United States); and others

    2016-01-11

    Research reactors host a wide range of activities that make use of the intense neutron fluxes generated at these facilities. Recent interest in performing measurements with relatively low event rates, e.g. reactor antineutrino detection, at these facilities necessitates a detailed understanding of background radiation fields. Both reactor-correlated and naturally occurring background sources are potentially important, even at levels well below those of importance for typical activities. Here we describe a comprehensive series of background assessments at three high-power research reactors, including γ-ray, neutron, and muon measurements. For each facility we describe the characteristics and identify the sources of the background fields encountered. The general understanding gained of background production mechanisms and their relationship to facility features will prove valuable for the planning of any sensitive measurement conducted therein.

  20. Background Radiation Measurements at High Power Research Reactors

    CERN Document Server

    Ashenfelter, J; Baldenegro, C X; Band, H R; Barclay, G; Bass, C D; Berish, D; Bowden, N S; Bryan, C D; Cherwinka, J J; Chu, R; Classen, T; Davee, D; Dean, D; Deichert, G; Dolinski, M J; Dolph, J; Dwyer, D A; Fan, S; Gaison, J K; Galindo-Uribarri, A; Gilje, K; Glenn, A; Green, M; Han, K; Hans, S; Heeger, K M; Heffron, B; Jaffe, D E; Kettell, S; Langford, T J; Littlejohn, B R; Martinez, D; McKeown, R D; Morrell, S; Mueller, P E; Mumm, H P; Napolitano, J; Norcini, D; Pushin, D; Romero, E; Rosero, R; Saldana, L; Seilhan, B S; Sharma, R; Stemen, N T; Surukuchi, P T; Thompson, S J; Varner, R L; Wang, W; Watson, S M; White, B; White, C; Wilhelmi, J; Williams, C; Wise, T; Yao, H; Yeh, M; Yen, Y -R; Zhang, C; Zhang, X

    2016-01-01

    Research reactors host a wide range of activities that make use of the intense neutron fluxes generated at these facilities. Recent interest in performing measurements with relatively low event rates, e.g. reactor antineutrino detection, at these facilities necessitates a detailed understanding of background radiation fields. Both reactor-correlated and naturally occurring background sources are potentially important, even at levels well below those of importance for typical activities. Here we describe a comprehensive series of background assessments at three high-power research reactors, including $\\gamma$-ray, neutron, and muon measurements. For each facility we describe the characteristics and identify the sources of the background fields encountered. The general understanding gained of background production mechanisms and their relationship to facility features will prove valuable for the planning of any sensitive measurement conducted therein.

  1. JUPITER-II Program: ANL analysis of ZPPR-13A and ZPPR-13B

    Energy Technology Data Exchange (ETDEWEB)

    Collins, P.J.; Brumbach, S.B. [comps.

    1984-08-01

    The ZPPR-13 experiments provide basic physics data for radial heterogeneous LMFBR cores of approximately 700MWe size. Assemblies ZPPR-13A, ZPPR-13B and ZPPR-13A comprised the JUPITER-II cooperative program between the U.S. Department of Energy (US DOE) and PNC of Japan. The measurements were made between August 1982 and April 1984. The core designs and the measurements were planned jointly by the two parties with substantial input from U.S. industrial interests to ensure coverage of the design requirements. This report describes in detail the results of the Argonne National Laboratory (ANL) analyses of phases 13A and 13B/1 and includes preliminary results for the later assemblies of phase 13B..

  2. Revised ANL-reported tensile data for V-Ti and V-Cr-Ti alloys

    Energy Technology Data Exchange (ETDEWEB)

    Billone, M.C. [Argonne National Lab., IL (United States)

    1997-08-01

    The tensile for all irradiated vanadium alloy samples and several unirradiated vanadium alloys tested at Argonne National Laboratory (ANL) have been critically reviewed and revised, as necessary. The review and revision are based on re-analyzing the original load-displacement strip-chart recording using a methodology consistent with current ASTM standards. No significant difference has been found between the newly-revised and previously-reported values of yield strength (YS) and ultimate tensile strength (UTS). However, by correctly subtracting the non-gauge-length displacement and linear gauge-length displacement from the total cross-head displacement, the uniform elongation (UE) of the gauge length decreases by 4-9% strain and the total elongation (TE) of the gauge length decreases by 1-7% strain. These differences are more significant for lower-ductility irradiated alloys than for higher-ductility alloys.

  3. Reduction zero-knowledge

    Institute of Scientific and Technical Information of China (English)

    ZHAO Yunlei; DENG Xiaotie; LEE C. H.; ZHU Hong

    2004-01-01

    The nature of zero-knowledge is re-examined and the evidence for the following belief is shown:the classic simulation based definitions of zero-knowledge(simulation zero-knowledge)may be somewhat too strong to include some "nice" protocols in which the malicious verifier seems to learn nothing but we do not know how to construct a zero-knowledge simulator for it.To overcome this problem a new relaxation of zero-knowledge,reduction zero-knowledge,is introduced.It is shown that reduction zero-knowledge just lies between simulation zero-knowledge and witness indistinguishability.Under the assumption of existence of one-way permutations a 4-round public-coin reduction zero-knowledge proof system for NP is presented and in practice this protocol works in 3 rounds since the first verifier's message can be fixed once and for all.

  4. A Theoretical and Experimental Research on Terahertz Electro-Optic Sampling at Near-Zero Optical Transmission Point

    Institute of Scientific and Technical Information of China (English)

    XU Shi-Xiang; CAI Hua

    2008-01-01

    We report an improved theoretical model to characterize terahertz electro-optic(EO)sampling detection operating at near crossed-polarizer design by considering the nonzero minimal transmission of polarizers and the polarization purlty of laser beam.The proof-of-concept experiments show that the model can give quiet reasonable explanations on many experimental phenomena in THz EO detection,e.g.the modulation depth vs the different optical biases,the noise level from the balance detector vs the input probe beam power,the main origin of the background light and the incomplete cancellation of noise from the laser intensity fluctuation in balanced detection.The terahertz signals and the noises are also measured based on two different EO sampling schemes for comparison.The measured results support our model very well.

  5. Overview of Multi-Kilowatt Free-Piston Stirling Power Conversion Research at Glenn Research Center

    Science.gov (United States)

    Geng, Steven M.; Mason, Lee S.; Dyson, Rodger W.; Penswick, L. Barry

    2008-01-01

    As a step towards development of Stirling power conversion for potential use in Fission Surface Power (FSP) systems, a pair of commercially available 1 kW class free-piston Stirling convertors and a pair of commercially available pressure wave generators (which will be plumbed together to create a high power Stirling linear alternator test rig) have been procured for in-house testing at Glenn Research Center (GRC). Delivery of both the Stirling convertors and the linear alternator test rig is expected by October 2007. The 1 kW class free-piston Stirling convertors will be tested at GRC to map and verify performance. The convertors will later be modified to operate with a NaK liquid metal pumped loop for thermal energy input. The high power linear alternator test rig will be used to map and verify high power Stirling linear alternator performance and to develop power management and distribution (PMAD) methods and techniques. This paper provides an overview of the multi-kilowatt free-piston Stirling power conversion work being performed at GRC.

  6. Zero Thermal Noise in Resistors at Zero Temperature

    Science.gov (United States)

    Kish, Laszlo B.; Niklasson, Gunnar A.; Granqvist, Claes-Göran

    2016-06-01

    The bandwidth of transistors in logic devices approaches the quantum limit, where Johnson noise and associated error rates are supposed to be strongly enhanced. However, the related theory — asserting a temperature-independent quantum zero-point (ZP) contribution to Johnson noise, which dominates the quantum regime — is controversial and resolution of the controversy is essential to determine the real error rate and fundamental energy dissipation limits of logic gates in the quantum limit. The Callen-Welton formula (fluctuation-dissipation theorem) of voltage and current noise for a resistance is the sum of Nyquist’s classical Johnson noise equation and a quantum ZP term with a power density spectrum proportional to frequency and independent of temperature. The classical Johnson-Nyquist formula vanishes at the approach of zero temperature, but the quantum ZP term still predicts non-zero noise voltage and current. Here, we show that this noise cannot be reconciled with the Fermi-Dirac distribution, which defines the thermodynamics of electrons according to quantum-statistical physics. Consequently, Johnson noise must be nil at zero temperature, and non-zero noise found for certain experimental arrangements may be a measurement artifact, such as the one mentioned in Kleen’s uncertainty relation argument.

  7. Theoretical Research of Coal Gasification Products Burning in Boilers at Tomsk Thermal Power Plant-3

    Directory of Open Access Journals (Sweden)

    Somov A.A.

    2015-01-01

    Full Text Available Mathematical modeling of primary fuel change into power gas in power generating boiler with productivity of steam 160 t\\h was done. Research of aggregate work on some power modes was completed. Characteristic curves of efficiency coefficient at different loads and ratio on power and natural gases burning were made. Practicability of power gas use as fuel was proved.

  8. An intrinsically safe facility for forefront research and training on nuclear technologies — A zero-power experiment

    Science.gov (United States)

    Alloni, D.; Borio di Tigliole, A.; Cagnazzo, M.; Magrotti, G.; Manera, S.; Panza, F.; Prata, M.; Salvini, A.; Cammi, A.; Chiesa, D.; Clemenza, M.; Previtali, E.; Sisti, M.

    2014-04-01

    The study of subcritical reactors needs some test to correctly evaluate many parameters that must be introduced in a reactor model. The Sub-critical Multiplication installation at the University of Pavia was used to measure neutron fluxes and multiplication factors that will be modelled with a MCNP Monte Carlo numerical simulation. The comparison between the measurements and the simulations were very promising demonstrating that also in a sub-critical system the Monte Carlo model could be very helpful in describing the reactor characteristics. Using all the collected data from measurements and simulations, it was possible to determine the k eff of the reactor plant with a reasonable accuracy. The ratio between the fast and the thermal component of the neutron fluxes was also determined.

  9. Power Analysis in Survey Research: Importance and Use for Health Educators

    Science.gov (United States)

    Price, James H.; Dake, Joseph A.; Murnan, Judy; Dimmig, Jaime; Akpanudo, Sutoidem

    2005-01-01

    This article has three purposes: to explain the two different uses of power analysis that can be used in health education research; to examine the extent to which power analysis is being used in published health education research; and to explain the implications of not using power analysis in research studies. Articles in seven leading health…

  10. Study and Practice of Zero Discharge Technology of Effluent form Thermal Power Plant%火电厂废水“零排放”技术研究与实践

    Institute of Scientific and Technical Information of China (English)

    肖婷; 夏克非

    2011-01-01

    随着中国经济的快速增长,水资源的短缺矛盾日益突出,实现废水“零排放”是火电厂可持续发展的必经之路。文章以重庆合川火电厂为例,介绍了各系统废水处理方式及回用途径,以实现火电厂废水“零排放”。%With the rapid rise of our national economy,the contradiction of water lacking becomes acute increasingly and the zero discharge of waste water is the necessity for sustained development of the themal power plant. This paper describes the treatment methods of waste water for various systems and the recycling usemethods at Chongqing Hechuan power plant in order to reach the goal of zero discharge technology of effluent form thermal power palnt.

  11. A Goal of Zero

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    As the picture of HIV/AIDS in China becomes more complex, more efforts are needed The theme of World AIDS Day this year is "Getting to Zero," which means zero new HIV infections, zero discrimination and zero AIDS-related deaths.Realizing these goals, however, is an extremely difficult challenge. Three decades after the first case of HIV was reported in the world in 1981, poor awareness and inadequate medical responses have allowed the virus to continue to spread worldwide.

  12. Proceedings of the first energy research power supercomputer users symposium

    Energy Technology Data Exchange (ETDEWEB)

    1991-01-01

    The Energy Research Power Supercomputer Users Symposium was arranged to showcase the richness of science that has been pursued and accomplished in this program through the use of supercomputers and now high performance parallel computers over the last year: this report is the collection of the presentations given at the Symposium. Power users'' were invited by the ER Supercomputer Access Committee to show that the use of these computational tools and the associated data communications network, ESNet, go beyond merely speeding up computations. Today the work often directly contributes to the advancement of the conceptual developments in their fields and the computational and network resources form the very infrastructure of today's science. The Symposium also provided an opportunity, which is rare in this day of network access to computing resources, for the invited users to compare and discuss their techniques and approaches with those used in other ER disciplines. The significance of new parallel architectures was highlighted by the interesting evening talk given by Dr. Stephen Orszag of Princeton University.

  13. Monolithic solid oxide fuel cell technology advancement for coal-based power generation. Quarterly technical status report, January--March 1992

    Energy Technology Data Exchange (ETDEWEB)

    1992-04-14

    The program is conducted by a team consisting of AiResearch Los Angeles Division of Allied-Signal Aerospace Company and Argonne National Laboratory (ANL). The objective of the program is to advance materials and fabrication methodologies to develop a monolithic solid oxide fuel cell (MSOFC) system capable of meeting performance, life, and cost goals for coal-based power generation. The program focuses on materials research and development, fabrication process development, cell/stack performance testing and characterization, cost and system analysis, and quality development.

  14. Physics with polarized beams. Report of the ANL Technical Advisory Panel. [Research with polarized proton beams

    Energy Technology Data Exchange (ETDEWEB)

    1975-11-01

    Experimental directions which will be the most useful in developing underlying theories of hadronic collisions are outlined. As a pedagogical device to accomplish this, approximate percentages of a total program which could be devoted to different areas have been quoted. Findings are presented in the form of a short basic report with several long detailed appendices. In the basic report our opinion as to the amount of polarized beam experimental effort that should be applied to the following areas is stated: nucleon-nucleon scattering, quasi-two-body processes, inclusive production, and new or unexplored areas (such as large p/sub T/ and invariance principles). Our reasoning is discussed briefly, however, the details are left for the appendices. Members of the panel present certain aspects of the above areas, which should be useful for planning and/or performing polarized beam experiments. The seven presentations are abstracted separately in ERA.

  15. Evaluating and Reporting Statistical Power in Counseling Research

    Science.gov (United States)

    Balkin, Richard S.; Sheperis, Carl J.

    2011-01-01

    Despite recommendations from the "Publication Manual of the American Psychological Association" (6th ed.) to include information on statistical power when publishing quantitative results, authors seldom include analysis or discussion of statistical power. The rationale for discussing statistical power is addressed, approaches to using "G*Power" to…

  16. International power supply policy and the globalisation of research: the example of fusion research

    Energy Technology Data Exchange (ETDEWEB)

    Bechmann, G.; Gloede, F. E-mail: fritz.gloede@itas.fzk.de; Lessmann, E

    2001-11-01

    At the present state of our information, we can affirm that fusion research, as far as the necessary financial expenditures and their political justification are concerned, is a matter of politically controversial debate. In the political arenas, projects like controlled nuclear fusion are discussed primarily with regard to the controllability of complex technical systems and the sustainability of our future supply of electric power. The attempt to discuss this problem will have to consider: (i) on the one hand, already established concepts of sustainability; (ii) and on the other, the - according to the present state of our knowledge - foreseeable characteristics of a system of power generation and supply based on fusion reactors. Not only do the goals of global technology projects have to be embedded in patterns of universally accepted legitimisation (sustainability), but the organisation of research and development is also changing into networks acting globally. In this sense, globalisation means not only the worldwide linking of financial markets and the permanent availability of information and communication networks, but above all the creation of global organisations of research and innovation processes. The globalisation of research and development of technology has several dimensions: (i) the recognition and treatment of global problems; (ii) the transformation and evolution of new forms of organisation and cooperation in a global community of researchers; (iii) the constitution of Global Change Research. Fusion is playing a 'pathfinder role' for these processes and is at the same time itself an expression of the globalisation of the production of technology.

  17. Liquid Nitrogen Zero Boiloff Testing

    Science.gov (United States)

    Plachta, David; Feller, Jeffrey; Johnson, Wesley; Robinson, Craig

    2017-01-01

    Cryogenic propellants such as liquid hydrogen (LH2) and liquid oxygen (LO2) are a part of NASAs future space exploration due to their high specific impulse for rocket motors of upper stages suitable for transporting 10s to 100s of metric tons of payload mass to destinations outside of low earth orbit and for their return. However, the low storage temperatures of LH2 and LO2 cause substantial boil-off losses for missions with durations greater than several months. These losses can be eliminated by incorporating high performance cryocooler technology to intercept heat load to the propellant tanks and modulating the cryocooler to control tank pressure. The active thermal control technology being developed by NASA is the reverse turbo-Brayton cycle cryocooler and its integration to the propellant tank through a distributed cooling tubing network coupled to the tank wall. This configuration was recently tested at NASA Glenn Research Center, in a vacuum chamber and cryo-shroud that simulated the essential thermal aspects of low Earth orbit, its vacuum and temperature. Testing consisted of three passive tests with the active cryo-cooler system off, and 7 active tests, with the cryocooler powered up. The test matrix included zero boil-off tests performed at 90 full and 25 full, and several demonstrations at excess cooling capacity and reduced cooling capacity. From this, the tank pressure response with varied cryocooler power inputs was determined. This test series established that the active cooling system integrated with the propellant tank eliminated boil-off and robustly controlled tank pressure.

  18. Research on Comparisons of New Clean Power Generation Technologies

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    On the basis of introducing clean power generation technologies, the author calculated and analyzed the investment, economy and environmental protection of these technologies, posed his views of giving the priorities to the development of supercritical and ultra-supercritical pressure coal-fired power generation technologies and taking vigorous action to nuclear power generation technology within the following 5-10 years, exploiting wind power within the following 10-15 years, and suggested that the installed capacity of nuclear power reach 80-100 GW and that of wind power reach 50-80 GW by 2020.

  19. 磁悬浮风力发电机零偏置电流控制策略研究%Control strategy with zero-bias current for magnetic levitation wind power generator

    Institute of Scientific and Technical Information of China (English)

    王晓; 谢振宇; 周红凯

    2014-01-01

    建立了5自由度磁悬浮轴承支撑的垂直轴风力发电机转子试验系统,研制了零偏置电流模拟控制器,通过试验方法研究了该控制器对系统动态性能的影响。结果表明,零偏置电流控制方式在显著降低磁悬浮轴承电能损耗的同时仍然能够保证垂直轴风力发电机转子系统稳定运行。%The setup of a vertical axis wind power generator rotor system with 5-DOF supported with active magnetic bearings was built.A zero-bias current analog controller was also developed.The influence of the controller on the dynamic performance of the system was investigated with the test method.The results showed that the zero-bias current analog controller can be used to reduce power loss of active magnetic bearings obviously,and also to guarantee safe and stable operation of the system at the same time.

  20. Small Radioisotope Power System Testing at NASA Glenn Research Center

    Science.gov (United States)

    Dugala, Gina; Bell, Mark; Oriti, Salvatore; Fraeman, Martin; Frankford, David; Duven, Dennis

    2013-01-01

    In April 2009, NASA Glenn Research Center (GRC) formed an integrated product team (IPT) to develop a Small Radioisotope Power System (SRPS) utilizing a single Advanced Stirling Convertor (ASC) with passive balancer. A single ASC produces approximately 80 We making this system advantageous for small distributed lunar science stations. The IPT consists of Sunpower, Inc., to provide the single ASC with a passive balancer, The Johns Hopkins University Applied Physics Laboratory (JHUAPL) to design an engineering model Single Convertor Controller (SCC) for an ASC with a passive balancer, and NASA GRC to provide technical support to these tasks and to develop a simulated lunar lander test stand. The single ASC with a passive balancer, simulated lunar lander test stand, and SCC were delivered to GRC and were tested as a system. The testing sequence at GRC included SCC fault tolerance, integration, electromagnetic interference (EMI), vibration, and extended operation testing. The SCC fault tolerance test characterized the SCCs ability to handle various fault conditions, including high or low bus power consumption, total open load or short circuit, and replacing a failed SCC card while the backup maintains control of the ASC. The integrated test characterized the behavior of the system across a range of operating conditions, including variations in cold-end temperature and piston amplitude, including the emitted vibration to both the sensors on the lunar lander and the lunar surface. The EMI test characterized the AC and DC magnetic and electric fields emitted by the SCC and single ASC. The vibration test confirms the SCCs ability to control the single ASC during launch. The extended operation test allows data to be collected over a period of thousands of hours to obtain long term performance data of the ASC with a passive balancer and the SCC. This paper will discuss the results of each of these tests.

  1. The power distribution and neutron fluence measurements and calculations in the VVER-1000 Mock-Up on the LR-0 research reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kostal, M.; Juricek, V.; Rypar, V.; Svadlenkova, M. [Research Center Rez Ltd., 250 68 Husinec-Rez 130 (Czech Republic); Cvachovec, F. [Univ. of Defence, Kounicova 65, 662 10 Brno (Czech Republic)

    2011-07-01

    The power density distribution in a reactor has significant influence on core structures and pressure vessel mechanical resistance, as well as on the physical characteristics of nuclear fuel. This quantity also has an effect on the leakage neutron and photon field. This issue has become of increasing importance, as it touches on actual questions of the VVER nuclear power plant life time extension. This paper shows the comparison of calculated and experimentally determined pin by pin power distributions. The calculation has been performed with deterministic and Monte Carlo approaches. This quantity is accompanied by the neutron and photon flux density calculation and measurements at different points of the light water zero-power (LR-0) research reactor mock-up core, reactor built-in component (core barrel), and reactor pressure vessel and model. The effect of the different data libraries used for calculation is discussed. (authors)

  2. Feasibility Research of Nuclear-power System for Car

    Institute of Scientific and Technical Information of China (English)

    WU; Xiao-chun; SUN; Zheng; LIU; Xin-ming; LI; Long; XU; Zhi-long; SHAO; Jing

    2013-01-01

    The idea of making nuclear-powered car can dated back to 1950s,and Ford company developed the first nuclear-powered car Nucleon which theoretically based on uranium-235 fission powered engine.Recently,General Motors released its Cadillac"World Thorium Fuel Concept"car at 2009 Chicago Auto Show,which didn’t include a working thorium-powered engine.But it’s claimed that the thorium laser

  3. Leveraging the power of pooled data for cancer outcomes research

    Institute of Scientific and Technical Information of China (English)

    Kiara Hugh-Yeun; Winson Y. Cheung

    2016-01-01

    Background: Clinical trials continue to be the gold standard for determining the effcacy of novel cancer treatments, but they may also expose participants to the potential risks of unpredictable or severe toxicities. The development of validated tools that better inform patients of the beneifts and risks associated with clinical trial participation can facilitate the informed consent process. The design and validation of such instruments are strengthened when we leverage the power of pooled data analysis for cancer outcomes research. Main body: In a recent study published in the Journal of Clinical Oncology entitled“Determinants of early mortal‑ity among 37,568 patients with colon cancer who participated in 25 clinical trials from the adjuvant colon cancer endpoints database,”using a large pooled analysis of over 30,000 study participants who were enrolled in clinical trials of adjuvant therapy for early‑stage colon cancer, we developed and validated a nomogram depicting the predictors of early cancer mortality. This database of pooled individual‑level data allowed for a comprehensive analysis of poor prognostic factors associated with early death;furthermore, it enabled the creation of a nomogram that was able to reliably capture and quantify the beneift‑to‑risk proifle for patients who are considering clinical trial participation. This tool can facilitate treatment decision‑making discussions. Conclusion: As China and other Asian countries continue to conduct oncology clinical trials, efforts to collate patient‑level information from these studies into a large data repository should be strongly considered since pooled data can increase future capacity for cancer outcomes research, which, in turn, can enhance patient‑physician discus‑sions and optimize clinical care.

  4. Microwave power transmitting phased array antenna research project

    Science.gov (United States)

    Dickinson, R. M.

    1978-01-01

    An initial design study and the development results of an S band RF power transmitting phased array antenna experiment system are presented. The array was to be designed, constructed and instrumented to permit wireless power transmission technology evaluation measurements. The planned measurements were to provide data relative to the achievable performance in the state of the art of flexible surface, retrodirective arrays, as a step in technically evaluating the satellite power system concept for importing to earth, via microwave beams, the nearly continuous solar power available in geosynchronous orbit. Details of the microwave power transmitting phased array design, instrumentation approaches, system block diagrams, and measured component and breadboard characteristics achieved are presented.

  5. 基于暂态零序能量的配电网故障选线方法研究%Research of Fault Line Selection Method of Distribution Network Based on Transient Zero-sequence Energy

    Institute of Scientific and Technical Information of China (English)

    田书; 何金朋; 聂赫

    2012-01-01

    针对中性点经消弧线圈接地系统发生单相接地故障时因故障边界复杂、随机,故障稳态分量小,零序瞬时功率倒相而导致传统的单一特征量选线方法失效问题,提出了一种新的基于暂态零序能量的选线方法.该方法通过一种数字滤波器来滤除暂态零序电流中的不对称分量和稳态工频分量,得到各条线路零序电流和母线零序电压的暂态纯故障分量,由此构造暂态零序能量,并根据暂态零序能量的大小和方向判断故障类型及线路,即发生单相接地故障时,非故障线路暂态零序能量的方向为正,故障线路暂态零序能量的方向为负,且其绝对值为其余线路暂态零序能量之和;发生母线接地故障时,母线暂态零序能量的大小为其余线路暂态零序能量之和.针对母线暂态零序能量受噪声影响大而导致选线灵敏度低的问题,提出将自动重合闸技术应用到该选线方法中的方案.Matlab仿真结果表明,该选线方法的准确性、可靠性较高.%For problem of ineffectiveness of traditional line selection methods by use of single feature value caused by complex and random fault borderline, small steady component of fault and reverse phase of instantaneous zero-sequence power when single-phase grounding fault happens in power system connected to earth through an arc suppression coil, the paper proposed a new method of line selection based on transient zero-sequence energy. The method filters nonsymmetrical component and steady component of transient zero-sequence current through a digital filter and gets zero-sequence current of each line and pure transient fault component of zero-sequence voltage of bus in order to get transient zero-sequence energy. Then the method judges fault type and line according to the value and direction of transient zero-sequence energy. When single-phase grounding fault happens, the direction of transient zero-sequence energy of non

  6. Poster abstract: A decentralized routing scheme based on a zero-sum game to optimize energy in solar powered sensor networks

    KAUST Repository

    Dehwah, Ahmad H.

    2014-04-01

    This poster is aimed at solving the problem of maximizing the energy margin of a solar-powered sensor network at a fixed time horizon, to maximize the network performance during an event to monitor. Using a game theoretic approach, the optimal routing maximizing the energy margin of the network at a given time under solar power forcing can be computed in a decentralized way and solved exactly through dynamic programming with a low overall complexity. We also show that this decentralized algorithm is simple enough to be implemented on practical sensor nodes. Such an algorithm would be very useful whenever the energy margin of a solar-powered sensor network has to be maximized at a specific time. © 2014 IEEE.

  7. 电厂脱硫废水正渗透膜浓缩零排放技术的应用%Application of MBC zero liquid discharge technology to desulfurization wastewater treatment in a power plant

    Institute of Scientific and Technical Information of China (English)

    邵国华; 方棣

    2016-01-01

    介绍了膜浓缩(MBC)零排放技术在长兴电厂脱硫废水深度处理项目中的应用情况。系统可将22 m3/h含盐水浓缩至1.5~2 m3/h,盐分浓缩至200 g/L左右后进入蒸发结晶系统,最终生成结晶盐,经过浓缩处理后的清洁产水作为电厂锅炉补给水回用。运行结果表明,MBC零排放系统运行良好,有效地保证了电厂的稳定运行,带来良好的社会和经济效益。%The application of membrane brine concentrator(MBC) zero liquid discharge technology to the advanced treatment project for desulfurization wastewater in Changxing Power Plant is introduced. 22 m3/h of wastewater containing salt is concentrated to 1.5-2 m3/h. After the salinity is concentrated to about 200 g/L ,it goes to evaporative crystal system,and finally forms crystal salt. After the concentration treatment,the produced clean water can be reused as boiler make-up water for the power plant. The results show that the MBC zero discharge system runs well,and guarentees stable running of Changxing Power Plant,bringing good social and economic benefits.

  8. 77 FR 9273 - WORKSHOP Sponsored by the Nuclear Regulatory Commission and the Electric Power Research Institute...

    Science.gov (United States)

    2012-02-16

    ... COMMISSION WORKSHOP Sponsored by the Nuclear Regulatory Commission and the Electric Power Research Institute on the Treatment of Probabilistic Risk Assessment Uncertainties: Public Meeting AGENCY: U.S. Nuclear...), Office of Nuclear Regulatory Research (RES), in cooperation with the Electric Power Research...

  9. Magnetic bearings with zero bias

    Science.gov (United States)

    Brown, Gerald V.; Grodsinsky, Carlos M.

    1991-01-01

    A magnetic bearing operating without a bias field has supported a shaft rotating at speeds up to 12,000 rpm with the usual four power supplies and with only two. A magnetic bearing is commonly operated with a bias current equal to half of the maximum current allowable in its coils. This linearizes the relation between net force and control current and improves the force slewing rate and hence the band width. The steady bias current dissipates power, even when no force is required from the bearing. The power wasted is equal to two-thirds of the power at maximum force output. Examined here is the zero bias idea. The advantages and disadvantages are noted.

  10. Research on Power Factor Correction Boost Inductor Design Optimization – Efficiency vs. Power Density

    DEFF Research Database (Denmark)

    Li, Qingnan; Andersen, Michael A. E.; Thomsen, Ole Cornelius

    2011-01-01

    Nowadays, efficiency and power density are the most important issues for Power Factor Correction (PFC) converters development. However, it is a challenge to reach both high efficiency and power density in a system at the same time. In this paper, taking a Bridgeless PFC (BPFC) as an example...

  11. 集成氧离子传输膜的CO2零排放固体氧化物燃料电池复合动力系统%Study on Zero CO2 Emission Solid Oxide Fuel Cell Hybrid Power Systems Integrated With Oxygen Ion Transport Membrane

    Institute of Scientific and Technical Information of China (English)

    2013-01-01

    In order to further reduce the energy consumption of CO2 recovery in the solid oxide fuel cell (SOFC) hybrid system, a new zero CO2 emission SOFC hybrid power system integrated with oxygen ion transport membrane (OTM) was proposed in this paper. With the method of unit consumption analysis, the energy consumption distribution characteristics of overall system were obtained, and then the effects of key operation parameters on the overall system performance were investigated. This paper also compared the performances of the new system with the zero CO2 emission SOFC hybrid power system integrated with the traditional cryogenic air separation unit. The results show that the new system still has high efficiency after CO2 recovery. Compared with other systems, the efficiency of the zero CO2 emission SOFC hybrid power system integrated with OTM is around 64.71%, only 2.16 percentage lower than that of the traditional SOFC hybrid power system (66.87%) without CO2 capture and 0.74 percentage higher than that of the zero CO2 emission SOFC hybrid system with the cryogenic air separation unit (63.97%). The research achievements provide valuable reference for further study on zero CO2 emissions SOFC hybrid power systems with higher efficiency.%  为了进一步降低固体氧化物燃料电池(solid oxide fuel cell,SOFC)复合系统回收 CO2的能耗,该文提出一个新型的集成氧离子传输膜(oxygen ion transport membrane,OTM)的 CO2零排放 SOFC 复合动力系统。利用单耗分析方法得到系统各单元的能耗分布情况,分析了SOFC的主要参数对整个系统性能的影响,并与集成传统深冷空分系统的零CO2排放SOFC复合动力系统进行了比较研究。研究结果表明:与不回收CO2的传统SOFC复合动力系统相比,与OTM集成的复合动力系统效率下降仅2.16个百分点,比与传统深冷空分系统集成的复合动力系统效率高0.74个百分点。该文研究成果可以为研究更高效

  12. [Research progress on key technology of power and signal transmission in neuroprosthetic].

    Science.gov (United States)

    Wang, Xing; Peng, Chenglin; Liu, Tao; Wang, Rui; Hou, Wensheng; Zheng, Xiaolin; Zheng, Erxin

    2011-10-01

    The power and signal transmission technology is one of the key technologies in neuroprosthetic research. This paper proposes firstly the related theory of power and signal transmission technology in neuroprosthetic, then summarizes the three key aspects of the power and signal transmission technology in neuroprosthetic. After analyzed the development of the inductive wireless power harvesting technology, the wireless telemetry technology and the wireless power harvesting telemetry technology, the emphasis on research contents will be proposed and discussed, which will help accelerate the further research of prosthetic.

  13. Fuel Cells: Power System Option for Space Research

    Science.gov (United States)

    Shaneeth, M.; Mohanty, Surajeet

    2012-07-01

    Fuel Cells are direct energy conversion devices and, thereby, they deliver electrical energy at very high efficiency levels. Hydrogen and Oxygen gases are electrochemically processed, producing clean electric power with water as the only by product. A typical, Fuel Cell based power system involve a Electrochemical power converter, gas storage and management systems, thermal management systems and relevant control units. While there exists different types of Fuel cells, Proton Exchange Membrane (PEM) Fuel Cells are considered as the most suitable one for portable applications. Generally, Fuel Cells are considered as the primary power system option in space missions requiring high power ( > 5kW) and long durations and also where water is a consumable, such as manned missions. This is primarily due to the advantage that fuel cell based power systems offer, in terms of specific energy. Fuel cells have the potential to attain specific energy > 500Wh/kg, specific power >500W/kg, energy density > 400Whr/L and also power density > 200 W/L. This apart, a fuel cell system operate totally independent of sun light, whereas as battery based system is fully dependent on the same. This uniqueness provides added flexibility and capabilities to the missions and modularity for power system. High power requiring missions involving reusable launch vehicles, manned missions etc are expected to be richly benefited from this. Another potential application of Fuel Cell would be interplanetary exploration. Unpredictable and dusty atmospheres of heavenly bodies limits sun light significantly and there fuel cells of different types, eg, Bio-Fuel Cells, PEMFC, DMFCs would be able to work effectively. Manned or unmanned lunar out post would require continuous power even during extra long lunar nights and high power levels are expected. Regenerative Fuel Cells, a combination of Fuel Cells and Electrolysers, are identified as strong candidate. While application of Fuel Cells in high power

  14. Outline of the safety research results, in the power reactor field, fiscal year 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-11-01

    The Power Reactor and Nuclear Fuel Development Corporation (PNC) has promoted the safety research in fiscal year of 1996 according to the Fundamental Research on Safety Research (fiscal year 1996 to 2000) prepared on March, 1996. Here is described on the research results in fiscal year 1996, the first year of the 5 years programme, and whole outline of the fundamental research on safety research, on the power reactor field (whole problems on the new nuclear converter and the fast breeder reactor field and problems relating to the power reactor in the safety for earthquake and probability theoretical safety evaluation field). (G.K.)

  15. Review of the status of low power research reactors and considerations for its development

    Energy Technology Data Exchange (ETDEWEB)

    Lim, In Cheol; Wu, Sang Ik; Lee, Byung Chul; Ha, Jae Joo [KAERI, Daejeon (Korea, Republic of)

    2012-10-15

    At present, 232 research reactors in the world are in operation and two thirds of them have a power less than 1 MW. Many countries have used research reactors as the tools for educating and training students or engineers and for scientific service such as neutron activation analysis. As the introduction of a research reactor is considered a stepping stone for a nuclear power development program, many newcomers are considering having a low power research reactor. The IAEA has continued to provide forums for the exchange of information and experiences regarding low power research reactors. Considering these, the Agency is recently working on the preparation of a guide for the preparation of technical specification possibly for a member state to use when wanting to purchase a low power research reactor. In addition, ANS has stated that special consideration should be given to the continued national support to maintain and expand research and test reactor programs and to the efforts in identifying and addressing the future needs by working toward the development and deployment of next generation nuclear research and training facilities. Thus, more interest will be given to low power research reactors and its role as a facility for education and training. Considering these, the status of low power research reactors was reviewed, and some aspects to be considered in developing a low power research reactor were studied.

  16. The research and development of the automatic solar power tracker

    Directory of Open Access Journals (Sweden)

    Li Yan Ping

    2016-01-01

    Full Text Available The article describes a kind of automatic tracker using solar power. It depends on two important parts which are servo system and adjusting mechanism system to keep the tracker operating normally. The article focuses on describing the characteristics and functions of two systems and the operating details of the automatic solar power tracker.

  17. A Reduced Wind Power Grid Model for Research and Education

    DEFF Research Database (Denmark)

    Akhmatov, Vladislav; Lund, Torsten; Hansen, Anca Daniela;

    2007-01-01

    A reduced grid model of a transmission system with a number of central power plants, consumption centers, local wind turbines and a large offshore wind farm is developed and implemented in the simulation tool PowerFactory (DIgSILENT). The reduced grid model is given by Energinet.dk, Transmission ...

  18. Tolerating Zero Tolerance?

    Science.gov (United States)

    Moore, Brian N.

    2010-01-01

    The concept of zero tolerance dates back to the mid-1990s when New Jersey was creating laws to address nuisance crimes in communities. The main goal of these neighborhood crime policies was to have zero tolerance for petty crime such as graffiti or littering so as to keep more serious crimes from occurring. Next came the war on drugs. In federal…

  19. Thermoelectric power of RAgSb(2) (R = Y, La, Ce, and Dy) in zero and applied magnetic fields.

    Science.gov (United States)

    Mun, E D; Bud'ko, S L; Canfield, P C

    2011-11-30

    We report the experimental results of measurements of the thermoelectric power on the ternary intermetallic compounds RAgSb(2) (R = Y, La, Ce, and Dy) over the temperature range from 2 to 300 K and in magnetic fields up to 140 kOe. In this work, we present the thermoelectric transport properties of four materials from the same family with different ground states: a non-moment bearing paramagnetic metallic system (YAgSb(2)), a non-moment bearing charge density wave system (LaAgSb(2)), a local moment bearing compound with XY-like antiferromagnetic order in the tetragonal basal plane as well as readily accessible metamagnetism (DyAgSb(2)), and a Kondo lattice system with ferromagnetic order below T(C) = 9.7 K (CeAgSb(2)). The thermoelectric power data from these materials exhibit complex temperature and magnetic field dependences, which are associated with modification of the electronic density of states and changes in magnetic scattering. At low temperatures, quantum oscillations in the thermoelectric power are also observed. These oscillations are associated with the Landau quantization of electronic energy in an applied magnetic field.

  20. Research on hybrid power filter of 6 kV power grid in coal mine

    Institute of Scientific and Technical Information of China (English)

    WANG Yu-feng; LI Jian

    2010-01-01

    Studied the harmonic control of the 6 kV power grid in a coal mine substation.Taking harmonic suppression and reactive power compensation into account, and complying with the economic and efficient technical line of the smart grid, a new hybrid active filter was proposed and applied to the power grid in the coal mine with the advantages such as large capacity, low cost and low loss. In order to improve detection speed and reduce the succeeding errors to improve the filtering performance of the active power filter,the DFT (Discrete Fourier Transform) sliding window algorithm based on coordinate transformation and improved hysteresis control method was proposed. The Matlab simulation results show that the hybrid active filter is satisfactory, can improve the grid power factor and can meet the requirements of improving the power quality in the coal mine.

  1. NASA Net Zero Energy Buildings Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    Pless, S.; Scheib, J.; Torcellini, P.; Hendron, B.; Slovensky, M.

    2014-10-01

    In preparation for the time-phased net zero energy requirement for new federal buildings starting in 2020, set forth in Executive Order 13514, NASA requested that the National Renewable Energy Laboratory (NREL) to develop a roadmap for NASA's compliance. NASA detailed a Statement of Work that requested information on strategic, organizational, and tactical aspects of net zero energy buildings. In response, this document presents a high-level approach to net zero energy planning, design, construction, and operations, based on NREL's first-hand experience procuring net zero energy construction, and based on NREL and other industry research on net zero energy feasibility. The strategic approach to net zero energy starts with an interpretation of the executive order language relating to net zero energy. Specifically, this roadmap defines a net zero energy acquisition process as one that sets an aggressive energy use intensity goal for the building in project planning, meets the reduced demand goal through energy efficiency strategies and technologies, then adds renewable energy in a prioritized manner, using building-associated, emission- free sources first, to offset the annual energy use required at the building; the net zero energy process extends through the life of the building, requiring a balance of energy use and production in each calendar year.

  2. Human factors research in Central Research Institute of Electric Power Industry creation of safety culture

    Energy Technology Data Exchange (ETDEWEB)

    Horie, Yasuo [Central Research Inst. of Electric Power Industry, Tokyo (Japan)

    2002-03-01

    To prevent accident of nuclear power plant, Human Factors Center was built in the Central Research Institute of Electric Power Industry in July 1987. It developed an evaluation method of human error cases and an application method of human factors information. Now it continues analysis and application of human factors information, development of training/work support tools and research/experiment of human behavior. Japan-Human Performance Evaluation System (J-HPES) was developed as an analytical system for analysis and evaluation of human factors related to the trouble and for using the result as the common property by storage the analytical results. J-HPES has a standard procedure consisted of collecting and analyzing data and proposing the countermeasures. The analytical results are arranged by 4 kinds of charts by putting into the form of a diagram. Moreover, it tries to find the causes with indirect and potential causes. Two kinds of materials, Caution Report and Human Factors Precept by means of Illustrations, are published. People can gain access to HFC database by URL http://criepi.denken.or.jp/CRIEPI/HFC/DB. To prevent these accidents, creation of human factors culture has been required. Five kinds of teaching materials and the training method are developed. (S.Y.)

  3. [Aiming for zero blindness].

    Science.gov (United States)

    Nakazawa, Toru

    2015-03-01

    comprehensive expression analyses or imaging data. This is an important area of research, since it promises to enable the exploration of targets for drug discovery and the identification of new biomarkers to efficiently detect glaucoma progression by applying new analysis strategies to the complex mass data. The project not only depends on the collaborative efforts of various types of clinical settings including private practices, medical centers and university hospitals, but also contributions of the pharmaceutical and the medical device industries. Thus, uniting a wide range of Japanese interests and resources is the key for success. In summary, in order to aim for ZERO BLINDNESS, a drastic improvement in the quality of our patient care, drug development research for unmet medical demands, and a strategic collaboration of various professionals in the ophthalmic industry are essential. With the deep appreciation we fell towards the selfless support extended during the earthquake disaster, we wish to translate our "gratitude" into "power" from Tohoku. In doing so, we as academicians are determined to keep on contributing to the society by making progress in the medicine.

  4. Does zero really mean nothing?-first experiences with the new PowerQuant(TM) system in comparison to established real-time quantification kits.

    Science.gov (United States)

    Poetsch, Micaela; Konrad, Helen; Helmus, Janine; Bajanowski, Thomas; von Wurmb-Schwark, Nicole

    2016-07-01

    DNA quantification is an important step in the molecular genetic analysis of a forensic sample, hopefully providing reliable data on DNA content for a subsequent generation of reproducible STR profiles for identification. For several years, this quantification has usually been done by real-time PCR protocols and meanwhile a variety of assays are commercially available from different companies. The newest one is the PowerQuant(TM) assay by Promega Inc. which is advertised with the promise that a determined DNA concentration of 0 ng/μl in a forensic sample guarantees the impossibility to achieve true STR results, thus allowing to exclude such samples from STR analysis to save time and money. Thus, the goal of this study was to thoroughly verify the quantification step with regard to its suitability as a screening method. We have evaluated the precision and reliability of four different real-time PCR quantification assays by systematically testing DNA dilutions and forensic samples with various DNA contents. Subsequently, each sample was subjected to the Powerplex® ESX 17 fast kit to determine a reliable cutoff level for exclusion of definitely negative samples from STR analysis. An accurate quantification of different cell line DNA dilutions was not possible with any kit. However, at least the PowerQuant(TM) assay provided suitable data analyzing forensic samples, whereas in other systems up to 46 % of negative samples still displayed reliable STR analysis results. All in all, the PowerQuant(TM) assay represents a big step forward, but the evaluation of real-time PCR quantification results has still to be done with great care.

  5. The PowerAtlas: a power and sample size atlas for microarray experimental design and research

    Directory of Open Access Journals (Sweden)

    Wang Jelai

    2006-02-01

    Full Text Available Abstract Background Microarrays permit biologists to simultaneously measure the mRNA abundance of thousands of genes. An important issue facing investigators planning microarray experiments is how to estimate the sample size required for good statistical power. What is the projected sample size or number of replicate chips needed to address the multiple hypotheses with acceptable accuracy? Statistical methods exist for calculating power based upon a single hypothesis, using estimates of the variability in data from pilot studies. There is, however, a need for methods to estimate power and/or required sample sizes in situations where multiple hypotheses are being tested, such as in microarray experiments. In addition, investigators frequently do not have pilot data to estimate the sample sizes required for microarray studies. Results To address this challenge, we have developed a Microrarray PowerAtlas 1. The atlas enables estimation of statistical power by allowing investigators to appropriately plan studies by building upon previous studies that have similar experimental characteristics. Currently, there are sample sizes and power estimates based on 632 experiments from Gene Expression Omnibus (GEO. The PowerAtlas also permits investigators to upload their own pilot data and derive power and sample size estimates from these data. This resource will be updated regularly with new datasets from GEO and other databases such as The Nottingham Arabidopsis Stock Center (NASC. Conclusion This resource provides a valuable tool for investigators who are planning efficient microarray studies and estimating required sample sizes.

  6. Renewable energy research 1995–2009: a case study of wind power research in EU, Spain, Germany and Denmark

    DEFF Research Database (Denmark)

    Sanz-Casado, Elias; Garcia- Zorita, J. Carlos; Serrano-López, Antonio Eleazar

    2013-01-01

    The paper reports the developments and citation patterns over three time periods of research on Renewable Energy generation and Wind Power 1995–2011 in EU, Spain, Germany and Denmark. Analyses are based on Web of Science and incorporate journal articles as well as conference proceeding papers...... terms to map knowledge export areas. Findings show an increase in citation impact for Renewable Energy and Wind Power research albeit hampered by scarcely cited conference papers. Although EU maintains its global top position in producing Renewable Energy and Wind Power research the developments of EU...... Wind Power research are EU-self citations. An expected intensified EU collaboration in the Wind Energy field does not come about. The most productive research institutions in Denmark and Spain are also the most cited ones....

  7. Research on Power Control of Wind Power Generation Based on Neural Network Adaptive Control

    Institute of Scientific and Technical Information of China (English)

    Hai-ying DONG; Chuan-hua SUN

    2010-01-01

    -For the characteristics of wind power generation system is multivariable,nonlinear and random,in this paper the neural network PID adaptive control is adopted.The size of pitch angle is adjusted in time to improve the performance of power control.The PID parameters are corrected by the gradient descent method,and Radial Basis Functinn(RBF)neural network is used as the system identifier in this method.Simulation results shaw that by using neural adaptive PID controller the generator power control can inhibit effectively the speed and affect the output power of generator.The dynamic performance and robustness of the controlled system is good,and the performance of wind power system is improved.

  8. Getting to Net Zero

    Energy Technology Data Exchange (ETDEWEB)

    2016-09-01

    The technology necessary to build net zero energy buildings (NZEBs) is ready and available today, however, building to net zero energy performance levels can be challenging. Energy efficiency measures, onsite energy generation resources, load matching and grid interaction, climatic factors, and local policies vary from location to location and require unique methods of constructing NZEBs. It is recommended that Components start looking into how to construct and operate NZEBs now as there is a learning curve to net zero construction and FY 2020 is just around the corner.

  9. Research on stochastic power-flow study methods. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Heydt, G. T. [ed.

    1981-01-01

    A general algorithm to determine the effects of uncertainty in bus load and generation on the output of conventional power flow analysis is presented. The use of statistical moments is presented and developed as a means for representing the stochastic process. Statistical moments are used to describe the uncertainties, and facilitate the calculations of single and multivarlate probability density functions of input and output variables. The transformation of the uncertainty through the power flow equations is made by the expansion of the node equations in a multivariate Taylor series about an expected operating point. The series is truncated after the second order terms. Since the power flow equations are nonlinear, the expected values of output quantities is in general not the solution to the conventional load flow problem using expected values of input quantities. The second order transformation offers a correction vector and allows the consideration of larger uncertainties which have caused significant error in the current linear transformation algorithms. Voltage controlled busses are included with consideration of upper and lower limits. The finite reactive power available at generation sites, and fixed ranges of transformer tap movement may have a significant effect on voltage and line power flow statistics. A method is given which considers limitation constraints in the evaluation of all output quantities. The bus voltages, line power flows, transformer taps, and generator reactive power requirements are described by their statistical moments. Their values are expressed in terms of the probability that they are above or below specified limits, and their expected values given that they do fall outside the limits. Thus the algorithm supplies information about severity of overload as well as probability of occurrence. An example is given for an eleven bus system, evaluating each quantity separately. The results are compared with Monte Carlo simulation.

  10. Discourses of power in mathematics education research: Concepts and possibilities for action

    DEFF Research Database (Denmark)

    Valero, Paola

    2008-01-01

    Mathematics education is powerful. This is an assertion that appears often in mathematics education research papers. However, the meaning of the assertion is far from being clear. An analysis of different ways of talking about power in relation to mathematics education, in research literature, is...

  11. Advanced underground Vehicle Power and Control: The locomotive Research Platform

    Energy Technology Data Exchange (ETDEWEB)

    Vehicle Projects LLC

    2003-01-28

    Develop a fuelcell mine locomotive with metal-hydride hydrogen storage. Test the locomotive for fundamental limitations preventing successful commercialization of hydride fuelcells in underground mining. During Phase 1 of the DOE-EERE sponsored project, FPI and its partner SNL, completed work on the development of a 14.4 kW fuelcell power plant and metal-hydride energy storage. An existing battery-electric locomotive with similar power requirements, minus the battery module, was used as the base vehicle. In March 2001, Atlas Copco Wagner of Portland, OR, installed the fuelcell power plant into the base vehicle and initiated integration of the system into the vehicle. The entire vehicle returned to Sandia in May 2001 for further development and integration. Initial system power-up took place in December 2001. A revision to the original contract, Phase 2, at the request of DOE Golden Field Office, established Vehicle Projects LLC as the new prime contractor,. Phase 2 allowed industry partners to conduct surface tests, incorporate enhancements to the original design by SNL, perform an extensive risk and safety analysis, and test the fuelcell locomotive underground under representative production mine conditions. During the surface tests one of the fuelcell stacks exhibited reduced power output resulting in having to replace both fuelcell stacks. The new stacks were manufactured with new and improved technology resulting in an increase of the gross power output from 14.4 kW to 17 kW. Further work by CANMET and Hatch Associates, an engineering consulting firm specializing in safety analysis for the mining industry, both under subcontract to Vehicle Projects LLC, established minimum requirements for underground testing. CANMET upgraded the Programmable Logic Control (PLC) software used to monitor and control the fuelcell power plant, taking into account locomotive operator's needs. Battery Electric, a South Africa manufacturer, designed and manufactured (at no cost

  12. Design and Research on Sigma-Delta Digital-to-Analog Converters for Audio Power Amplifiers

    OpenAIRE

    Puidokas, Vytenis

    2011-01-01

    The dissertation investigates the issues of analyzing a digital Sigma-Delta digital-to-analog converter (DAC) for audio power amplifiers. The main objects of research include a digital Sigma-Delta audio power DAC, improvement of its structure and an experimental research. The primary purpose of the dissertation is to suggest methods for improvement the structure of digital Sigma-Delta audio power DAC interpolator and the converter analysis. Disertacijoje nagrinėjami Sigma-Delta skaitmenini...

  13. Building and Researching the Bidding Model Based on the Cost of Power Plant

    Institute of Scientific and Technical Information of China (English)

    秦春申; 叶春; 赵景峰

    2004-01-01

    A bidding model of neural network was presented to pursue the largest benefit according to the policy of separating power plants from network and bidding transaction. This model bases on the cost of power plant and its research object is a power plant in the market. The market clearing price (MCP) can be predicted and an optimized load curve can be decided in this model. The model may provide technical support for the power plant.

  14. Reflections on Researcher Identity and Power: The Impact of Positionality on Community Based Participatory Research (CBPR) Processes and Outcomes.

    Science.gov (United States)

    Muhammad, Michael; Wallerstein, Nina; Sussman, Andrew L; Avila, Magdalena; Belone, Lorenda; Duran, Bonnie

    2015-11-01

    The practice of community based participatory research (CBPR) has evolved over the past 20 years with the recognition that health equity is best achieved when academic researchers form collaborative partnerships with communities. This article theorizes the possibility that core principles of CBPR cannot be realistically applied unless unequal power relations are identified and addressed. It provides theoretical and empirical perspectives for understanding power, privilege, researcher identity and academic research team composition, and their effects on partnering processes and health disparity outcomes. The team's processes of conducting seven case studies of diverse partnerships in a national cross-site CBPR study are analyzed; the multi-disciplinary research team's self-reflections on identity and positionality are analyzed, privileging its combined racial, ethnic, and gendered life experiences, and integrating feminist and post-colonial theory into these reflections. Findings from the inquiry are shared, and incorporating academic researcher team identity is recommended as a core component of equalizing power distribution within CBPR.

  15. Zero emission city. Preliminary study; Null-Emissions-Stadt. Sondierungsstudie

    Energy Technology Data Exchange (ETDEWEB)

    Diefenbach, N.; Enseling, A.; Werner, P.; Flade, A.; Greiff, R.; Hennings, D.; Muehlich, E.; Wullkopf, U.; Sturm, P.; Kieslich, W.; Born, R.; Grossklos, M.; Hatteh, R.; Mueller, K.; Ratschow, A.; Valouch-Fornoff, C.

    2002-10-01

    The idea of a 'zero emission city' is investigated by the Institut Wohnen und Umwelt on behalf of the Federal Minister of Education and Research. After describing the current situation and defining the key parameters of a 'zero emission city', settlement structures, power supply, production processes and transportation are analyzed and linked with the communal action level to obtain a framework for research, activities and actions. The study ends with recommendations for a research programme 'zero emission city'. (orig.) [German] Die von den Staedten der Industrielaender ausgehenden Emissionen stellen im Hinblick auf die globalen Belastungen wie z.B. Treibhauseffekt, Ozonabbau und Versauerung das Hauptproblem dar. Aus diesem Grunde bietet es sich an, den Gedanken der 'Null-Emissions-Stadt', der Vision einer moeglichst emissionsfreien Stadt, aufzugreifen und auf seine Tragfaehigkeit fuer innovative Handlungsmodelle forschungsstrategisch zu ueberpruefen. Das Bundesministerium fuer Bildung und Forschung hat das Institut Wohnen und Umwelt beauftragt, in einer Sondierungsstudie dieser Fragestellung nachzugehen. Nach der Festlegung der Ausgangsbedingungen und Eckpunkte der Vision 'Null-Emissions-Stadt' und der Analyse der vier Handlungsfelder Siedlungsstrukturen, Energieversorgung, Produktionsprozesse (Kreislaufwirtschaft) und Verkehr werden diese aufgegriffen und mit der kommunalen Handlungsebene verknuepft und zu einem Forschungs-, Handlungs- und moeglichen Aktionsrahmen zusammengefuegt. Die Studie schliesst mit Hinweisen fuer die Gestaltung eines Forschungsprogramms 'Null-Emissions-Stadt'. (orig.)

  16. Research on Reliability Assessment Zero- failure Data of Engine%发动机无失效数据可靠性评估研究

    Institute of Scientific and Technical Information of China (English)

    韩庆田; 李文强; 曹文静

    2012-01-01

    在定时截尾寿命试验特别是高可靠性、小子样试验中的无失效数据,引入了逆Weibull寿命分布函数,提出采用不完全Beta分布作为故障概率的先验分布,给出分布参数的最小二乘估计以及故障概率的Bayes估计和多层Bayes估计,从而得到可靠度的估计.最后针对实际问题进行了计算,结果表明Bayes估计稳定合理且容易计算,假定发动机寿命服从逆Weibull分布时的计算结果具有较高精度和较小的偏差.%In the time-censored life tests, zero-failure data is always obtained, especially in high reliability and small sampling tests. In the paper, Inverse Weibull distribution was introduced into the zero-failure data analysis. Concerning characters of zero-failure data,the incomplete Beta distribution was taken as an prior distribution of the failure probability, in order to estimate the failure probability using the Bayesian method. The least squares estimates of the distribution parameters were given, and hierarchical Bayesian estimation of failure probability of zero-failure data was presented,so that the reliability estimation of zero - failure data was obtained. Finally, calculations were performed concerning practical problems to illustrate the estimations developed in this paper. The result shows that the Bayesian estimations are stable, feasible and easy to operate, and the Inverse Weibull distribution is a reasonable alternative distribution to the life of engine, with less error.

  17. Research Needs: Prime-Power for High Energy Space Systems.

    Science.gov (United States)

    1982-06-01

    34The MHD Disk Generator as a Multimegawatt Power Supply Operating with Chemical and Nuclear Sources" 1. Louis, J. F., "Disk Generator", AIAA J., Vol. VI...May 16-18, 1977. 8. Lytle, J. K. and Louis, J. F., "The Effects of AnisotropicNonuniformities in a Nonequilibrium MHD Disk Generator , presented at

  18. Research on calorimeter for high-power microwave measurements

    Energy Technology Data Exchange (ETDEWEB)

    Ye, Hu; Ning, Hui; Yang, Wensen; Tian, Yanmin; Xiong, Zhengfeng; Yang, Meng; Yan, Feng; Cui, Xinhong [Science and Technology on High Power Microwave Laboratory, Northwest Institute of Nuclear Technology, Xi’an, Shaanxi 710024 (China)

    2015-12-15

    Based on measurement of the volume increment of polar liquid that is a result of heating by absorbed microwave energy, two types of calorimeters with coaxial capacitive probes for measurement of high-power microwave energy are designed in this paper. The first is an “inline” calorimeter, which is placed as an absorbing load at the end of the output waveguide, and the second is an “offline” calorimeter that is placed 20 cm away from the radiation horn of the high-power microwave generator. Ethanol and high density polyethylene are used as the absorbing and housing materials, respectively. Results from both simulations and a “cold test” on a 9.3 GHz klystron show that the “inline” calorimeter has a measurement range of more than 100 J and an energy absorption coefficient of 93%, while the experimental results on a 9.3 GHz relativistic backward-wave oscillator show that the device’s power capacity is approximately 0.9 GW. The same experiments were also carried out for the “offline” calorimeter, and the results indicate that it can be used to eliminate the effects of the shock of the solenoid on the measurement curves and that the device has a higher power capacity of 2.5 GW. The results of the numerical simulations, the “cold tests,” and the experiments show good agreement.

  19. Coarsening dynamics of zero-range processes

    Science.gov (United States)

    Godrèche, Claude; Drouffe, Jean-Michel

    2017-01-01

    We consider a class of zero-range processes exhibiting a condensation transition in the stationary state, with a critical single-site distribution decaying faster than a power law. We present the analytical study of the coarsening dynamics of the system on the complete graph, both at criticality and in the condensed phase. In contrast with the class of zero-range processes with critical single-site distribution decaying as a power law, in the present case the role of finite-time corrections is essential for the understanding of the approach to scaling.

  20. Zero-sequence current decoupling control of three-phase four-wire active power filter%四桥臂有源滤波器零序电流解耦预测电流控制

    Institute of Scientific and Technical Information of China (English)

    王晓刚; 张杰

    2016-01-01

    针对应用于三相四线制系统中的三相四桥臂有源电力滤波器的特点,研究了一种基于零序电流解耦的预测电流控制方法,分析了零序电流解耦的原理,设计了控制系统。该方法有效地解除了第四桥臂和前三桥臂的耦合,对中线电流进行独立补偿,与三相三桥臂的控制方法兼容,简单易行,易于对三桥臂有源电力滤波器进行改造后应用于三相四线系统。仿真分析表明,与其他方法相比,基于零序电流解耦的预测电流控制可使有源电力滤波器获得更好的补偿性能,电源电流总谐波畸变率和中线电流正负峰值均达到最小。%Zero-sequence current decoupling based predictive current control of three-phase four-wire active power filter (APF)is studied based on the characteristics of three-phase four-leg APF.The principle of zero-se-quence decoupling is analyzed and the control system is designed.The control method eliminates the coupling between the first three legs and the fourth leg,and the neutral current is compensated independently.The meth-od is compatible with the control of three-phase three-leg APF and is simple to implement.It is easy to upgrade the three-leg APF to meet the three-phase four wire applications.Simulation analyses show that zero-sequence current decoupling based predictive current control achieves better compensation performance than other meth-ods,total harmonic distortion of supply currents and positive /negative amplitudes of neutral current are both with minimum.

  1. Variable-Speed Power-Turbine Research at Glenn Research Center

    Science.gov (United States)

    Welch, Gerard E.; McVetta, Ashlie B.; Stevens, Mark A.; Howard, Samuel A.; Giel, Paul W.; Ameri, Ali, A.; To, Waiming; Skoch, Gary J.; Thurman, Douglas R.

    2012-01-01

    The main rotors of the NASA Large Civil Tilt-Rotor (LCTR) notional vehicle operate over a wide speed-range, from 100 percent at takeoff to 54 percent at cruise. The variable-speed power turbine (VSPT) offers one approach by which to effect this speed variation. VSPT aerodynamics challenges include high work factors at cruise, wide (40 to 60 ) incidence-angle variations in blade and vane rows over the speed range, and operation at low Reynolds numbers. Rotordynamics challenges include potential responsiveness to shaft modes within the 50 percent VSPT speed-range. A research effort underway at NASA Glenn Research Center, intended to address these key aerodynamic and rotordynamic challenges, is described. Conceptual design and 3-D multistage RANS and URANS analyses, conducted internally and under contract, provide expected VSPT sizing, stage-count, performance and operability information, and maps for system studies. Initial steps toward experimental testing of incidence-tolerant blading in a transonic linear cascade are described, and progress toward development/improvement of a simulation capability for multistage turbines with low Reynolds number transitional flow is summarized. Preliminary rotordynamics analyses indicate that viable concept engines with 50 percent VSPT shaft-speed range. Assessments of potential paths toward VSPT component-level testing are summarized.

  2. Final Technical Report for Photovoltaic Power Electronics Research Initiative (PERI)

    Energy Technology Data Exchange (ETDEWEB)

    Amirahmadi, Ahmadreza [Univ. of Central Florida, Orlando, FL (United States); Jordan, Charlie [Univ. of Central Florida, Orlando, FL (United States); batarseh, Issa [Univ. of Central Florida, Orlando, FL (United States)

    2015-08-31

    The Power Electronics team at the University of Central Florida (UCF) has developed a novel three-phase micro-inverter for photovoltaic (PV) distributed applications. Based on a new advanced topology and control methodology, the developed inverter is small in size, and achieved DoE targeted power density, cost and efficiency specifications. Today’s inverters are widely used in PV based energy harvesting systems, but are based on single-phase design with limited application to large installations. These micro-inverters have been shown to have advantageous over their string inverter counterparts in both grid-tied PV energy harvesting and standalone micro-grid systems with energy storage. Some of these are simplified installation, no high voltage DC wiring, no single point of failure and improved energy harvesting. Several patents have been issued and this new solar conversion technology has been licensed to the private sector.

  3. Nuclear power and the public: analysis of collected survey research

    Energy Technology Data Exchange (ETDEWEB)

    Melber, B.D.; Nealey, S.M.; Hammersla, J.; Rankin, W.L.

    1977-11-01

    This executive summary highlights the major findings of a comprehensive synthesis and analysis of over 100 existing surveys dealing with public attitudes toward nuclear power issues. Questions of immediate policy relevance to the nuclear debate are posed and answered on the basis of these major findings. For each issue area, those sections of the report in which more-detailed discussion and presentation of relevant data may be found are indicated.

  4. Research Of The Efficiency Of The Wireless Power Transfer With The Employment Of DD Inductance Coils

    Directory of Open Access Journals (Sweden)

    Krainyukov Alexander

    2015-12-01

    Full Text Available The paper is devoted to using of DD inductance coils for the wireless power transfer. The aim of the given research is to determine influence of the parameters of resonance transformer on the efficiency of the wireless power transfer with the use of the DD inductance coils. Experimental installation of the wireless power transfer by a resonance inductive method was constructed. Experiments were performed with it help. Research results show influence of the distance between the coils of inductance, of the resonance transformer frequency, of the storage source voltage and of the temperature conditions on the efficiency of the wireless power transfer.

  5. Understanding Net Zero Energy Buildings

    DEFF Research Database (Denmark)

    Salom, Jaume; Widén, Joakim; Candanedo, José

    2011-01-01

    Although several alternative definitions exist, a Net-Zero Energy Building (Net ZEB) can be succinctly described as a grid-connected building that generates as much energy as it uses over a year. The “net-zero” balance is attained by applying energy conservation and efficiency measures...... and by incorporating renewable energy systems. While based on annual balances, a complete description of a Net ZEB requires examining the system at smaller time-scales. This assessment should address: (a) the relationship between power generation and building loads and (b) the resulting interaction with the power grid....... This paper presents and categorizes quantitative indicators suitable to describe both aspects of the building’s performance. These indicators, named LMGI - Load Matching and Grid Interaction indicators, are easily quantifiable and could complement the output variables of existing building simulation tools...

  6. 零知识数字水印检测协议研究%Research on Zero Knowledge Proof Protocol of Watermark Detection

    Institute of Scientific and Technical Information of China (English)

    周四清; 余英林; 陈潮填

    2003-01-01

    The advent of the Web, electronic commerce and the creation of electronic distribution channels for contenthave brought new challenges regarding the protection of intellectual property. Digital watermarking is a new informa-tion security technique. Using zero knowledge proofs in the cryptography we proposea watermark detection based onzero knowledge, of solving that the existence of a watermark without revealing what the watermark is , of providingthe security when we apply watermarking.

  7. A new digital pulse power supply in heavy ion research facility in Lanzhou

    Science.gov (United States)

    Wang, Rongkun; Chen, Youxin; Huang, Yuzhen; Gao, Daqing; Zhou, Zhongzu; Yan, Huaihai; Zhao, Jiang; Shi, Chunfeng; Wu, Fengjun; Yan, Hongbin; Xia, Jiawen; Yuan, Youjin

    2013-11-01

    To meet the increasing requirements of the Heavy Ion Research Facility in Lanzhou-Cooler Storage Ring (HIRFL-CSR), a new digital pulse power supply, which employs multi-level converter, was designed. This power supply was applied with a multi H-bridge converters series-parallel connection topology. A new control model named digital power supply regulator system (DPSRS) was proposed, and a pulse power supply prototype based on DPSRS has been built and tested. The experimental results indicate that tracking error and ripple current meet the requirements of this design. The achievement of prototype provides a perfect model for HIRFL-CSR power supply system.

  8. IMPACT XP: An Integrated Performance/Power Analysis Framework for Compiler and Architecturefor Research

    Institute of Scientific and Technical Information of China (English)

    WANGYongwen; ZHANGMinxuan

    2004-01-01

    Modern high performance microprocessor design requires making power and performance tradeoffs at early phase, while traditional power analysis tools can't satisfy this requirement. Wattch provides an architectural power evaluation methodology within the SimpleScalar toolset; however current high-level power estimating tools still have limitations in functionality and range of research. In this paper, IMPACT XP is presented as a novel micro-architecture level power and performance analysis framework for both superscalar and EPIC architecture. In this framework, processors are divided into blocks at architecture abstraction layer. Wattch powermodels are implemented to estimate the peak power of each block and a cycle-accurate simulator is setup to calculate the dynamic energy dissipations and performance statistics. User-friendly interfaces are also provided. Experiments show that the framework maintains error within 10% of the estimated results against the reported values for exampling commercial microprocessors. Based on this framework, quantitative researches have been made on the additional power effects of modern compiler's performance optimization technologies and the inherited power characteristics of superscalar and EPIC architecture. IMPACT XP provides a power and performance analysis methodology by implementing analytical power models within the portable and familiar IMPACT compiler. It will facilitate architecture and compiler research in the poweraware field.

  9. PowerPoint Presentations: A Creative Addition to the Research Process.

    Science.gov (United States)

    Perry, Alan E.

    2003-01-01

    Contends that the requirement of a PowerPoint presentation as part of the research process would benefit students in the following ways: learning how to conduct research; starting their research project sooner; honing presentation and public speaking skills; improving cooperative and social skills; and enhancing technology skills. Outlines the…

  10. Computer Security for Commercial Nuclear Power Plants - Literature Review for Korea Hydro Nuclear Power Central Research Institute

    Energy Technology Data Exchange (ETDEWEB)

    Duran, Felicia Angelica [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Security Systems Analysis Dept.; Waymire, Russell L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States). Security Systems Analysis Dept.

    2013-10-01

    Sandia National Laboratories (SNL) is providing training and consultation activities on security planning and design for the Korea Hydro and Nuclear Power Central Research Institute (KHNPCRI). As part of this effort, SNL performed a literature review on computer security requirements, guidance and best practices that are applicable to an advanced nuclear power plant. This report documents the review of reports generated by SNL and other organizations [U.S. Nuclear Regulatory Commission, Nuclear Energy Institute, and International Atomic Energy Agency] related to protection of information technology resources, primarily digital controls and computer resources and their data networks. Copies of the key documents have also been provided to KHNP-CRI.

  11. Modernization of forest biomass operations research : powered by the EU

    Energy Technology Data Exchange (ETDEWEB)

    Roser, D. [Finnish Forest Research Inst., Joensuu (Finland)

    2010-07-01

    The European Union (EU) COST framework to support the modernization of forest biomass operations research in Europe was discussed along with the commitment to strengthen Europe's role as a world leader in forest biomass energy production and use. Initiated in 2009, the COST action aims to harmonize forest energy terminologies, methodologies, and biomass availability calculations by supporting technology transfer and research capacity related to the biomass procurement chain and sustainable forest management practices. The action will develop best practice guidelines, standard measurement and sampling methods, and a format for cost calculations. The action will allow scientists from Europe as well as other countries to communicate and exchange knowledge of topics related to the biomass industry. An electronic peer-reviewed online journal will also be established to improve the availability of research to all stakeholders.

  12. Research of on-line detection system for power capacitor

    Science.gov (United States)

    Yao, Junda; Qian, Zheng; Yu, Hao; Xia, Jiuyun

    2016-01-01

    The hidden danger exists in the power capacitor of power system due to long-time operation under the environment of high voltage. Thus, it is possible to induce serious fault, and the on-line detection system is urgently required. In this paper, two methods of the on-line detection system are compared in order to realize the better real-time condition detection. The first method is based on the STM microprocessor with an internal 12 bit A/D converter, which converts analog signals which is arrived from the sample circuit into digital signals, and then the FFT algorithm is used to accomplish the measurement of the voltage and current values of the capacitor. The second method is based on the special electric energy metering IC, which can obtain RMS (Root Mean Square) of voltage and current by processing the sampled data of the voltage and current, and store RMS of voltage and current in its certain registers. The operating condition of the capacitor can be obtained after getting the values of voltage and current. By comparing the measuring results of two methods, the second method could achieve a higher measurement accuracy and more simple construction.

  13. ALICE Zero Degree Calorimeter

    CERN Multimedia

    De Marco, N

    2013-01-01

    Two identical sets of calorimeters are located on both sides with respect to the beam Interaction Point (IP), 112.5 m away from it. Each set of detectors consists of a neutron (ZN) and a proton (ZP) Zero Degree Calorimeter (ZDC), positioned on remotely controlled platforms. The ZN is placed at zero degree with respect to the LHC beam axis, between the two beam pipes, while the ZP is positioned externally to the outgoing beam pipe. The spectator protons are separated from the ion beams by means of the dipole magnet D1.

  14. Reflecting on Power Relationships in the 'Doing' of Rural Cultural Research

    Directory of Open Access Journals (Sweden)

    Rae Dufty

    2010-02-01

    Full Text Available Foucaultian understandings of power have come to be highly influential in the how we analyse and write up rural cultural research. However, despite the extensive application of his work, Foucault’s retheorisation of power has been less consistently applied to how we ‘do’ rural cultural research. While researchers have sought to recognise and develop appropriate strategies around the role of power in how research is conducted, we have been less specific regarding how we theorise and apply our concepts of power when reflecting on the research process. It is the implications of this lack of theoretical rigour, combined with institutional constructions of research relationships, that this paper seeks to interrogate. Drawing on research conducted as part of doctorate, this article analyses the diverse ways in which participants from four New South Wales rural public housing communities negotiated the research relationship with myself and influenced the way this research was conducted and what became the final research project. Ultimately, this article argues that issues of theoretical consistency are fundamental to the overall integrity of reflexive processes when doing rural cultural research.

  15. Reflecting on power relationships in the 'doing' of rural cultural research

    Directory of Open Access Journals (Sweden)

    Dufty, Rae

    2010-01-01

    Full Text Available Foucaultian understandings of power have come to be highly influential in the how we analyse and write up rural cultural research. However, despite the extensive application of his work, Foucault’s retheorisation of power has been less consistently applied to how we ‘do’ rural cultural research. While researchers have sought to recognise and develop appropriate strategies around the role of power in how research is conducted, we have been less specific regarding how we theorise and apply our concepts of power when reflecting on the research process. It is the implications of this lack of theoretical rigour, combined with institutional constructions of research relationships, that this paper seeks to interrogate. Drawing on research conducted as part of doctorate, this article analyses the diverse ways in which participants from four New South Wales rural public housing communities negotiated the research relationship with myself and influenced the way this research was conducted and what became the final research project. Ultimately, this article argues that issues of theoretical consistency are fundamental to the overall integrity of reflexive processes when doing rural cultural research.

  16. Degree-day Modeling of Carob moth [Apomyelois (=Ectomyelois) ceratoniae Zell. (Lepidoptera: Pyralidae)] in pomegranate orchards in Şanlıurfa province

    OpenAIRE

    mamay, mehmet; ÜNLÜ, Levent; Yanık, Ertan; İkinci, Ali

    2014-01-01

    This study was conducted to determine degree-day modeling of carob moth [Apomyelois (=Ectomyelois) ceratoniae Zell. (Lepidoptera: Pyralidae)] under field conditions in pomegranate orchards in Şanlıurfa province during the years 2011 and 2012. Delta pheromone traps were used to determine population development of carob moth in Şanlıurfa Central and Siverek counties. HOBO data logger was used to record temperature hourly in order to calculate degree-day values of the pest in Şanliurfa Central a...

  17. Got Power? A Systematic Review of Sample Size Adequacy in Health Professions Education Research

    Science.gov (United States)

    Cook, David A.; Hatala, Rose

    2015-01-01

    Many education research studies employ small samples, which in turn lowers statistical power. We re-analyzed the results of a meta-analysis of simulation-based education to determine study power across a range of effect sizes, and the smallest effect that could be plausibly excluded. We systematically searched multiple databases through May 2011,…

  18. Power Matters: Foucault's "Pouvoir/Savoir" as a Conceptual Lens in Information Research and Practice

    Science.gov (United States)

    Olsson, Michael; Heizmann, Helena

    2015-01-01

    Introduction: This paper advocates Foucault's notion of pouvoir/savoir (power/knowledge) as a conceptual lens that information researchers might fruitfully use to develop a richer understanding of the relationship between knowledge and power. Methods: Three of the authors' earlier studies are employed to illustrate the use of this conceptual lens.…

  19. A COMPREHENSIVE MODEL FOR THE POWER TRANSFORMER DIGITAL DIFFERENTIAL PROTECTION FUNCTIONING RESEARCH

    Directory of Open Access Journals (Sweden)

    Yu. V. Rumiantsev

    2016-01-01

    Full Text Available This article presents a comprehensive model for the two-winding power transformer digital differential protection functioning research. Considered comprehensive model is developed in MatLab-Simulink dynamic simulation environment with the help of SimPowerSystems component library and includes the following elements: power supply, three-phase power transformer, wye-connected current transformers and two-winding power transformer digital differential protection model. Each element of the presented model is described in the degree sufficient for its implementation in the dynamic simulation environment. Particular attention is paid to the digital signal processing principles and to the ways of differential and restraining currents forming of the considered comprehensive model main element – power transformer digital differential protection. With the help of this model the power transformer digital differential protection functioning was researched during internal and external faults: internal short-circuit, external short-circuit with and without current transformers saturation on the power transformer low-voltage side. Each experiment is illustrated with differential and restraining currents waveforms of the digital differential protection under research. Particular attention was paid to the digital protection functioning analysis during power transformer abnormal modes: overexcitation and inrush current condition. Typical current waveforms during these modes were showed and their harmonic content was investigated. The causes of these modes were analyzed in details. Digital differential protection blocking algorithms based on the harmonic content were considered. Drawbacks of theses algorithms were observed and the need of their further technical improvement was marked.

  20. A new digital pulse power supply in heavy ion research facility in Lanzhou

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Rongkun, E-mail: wangrongkun@impcas.ac.cn [Institute of Modern Physics, Lanzhou, 730000 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Chen, Youxin; Huang, Yuzhen; Gao, Daqing; Zhou, Zhongzu; Yan, Huaihai [Institute of Modern Physics, Lanzhou, 730000 (China); Zhao, Jiang; Shi, Chunfeng; Wu, Fengjun [Institute of Modern Physics, Lanzhou, 730000 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Yan, Hongbin; Xia, Jiawen; Yuan, Youjin [Institute of Modern Physics, Lanzhou, 730000 (China)

    2013-11-01

    To meet the increasing requirements of the Heavy Ion Research Facility in Lanzhou-Cooler Storage Ring (HIRFL-CSR), a new digital pulse power supply, which employs multi-level converter, was designed. This power supply was applied with a multi H-bridge converters series-parallel connection topology. A new control model named digital power supply regulator system (DPSRS) was proposed, and a pulse power supply prototype based on DPSRS has been built and tested. The experimental results indicate that tracking error and ripple current meet the requirements of this design. The achievement of prototype provides a perfect model for HIRFL-CSR power supply system. -- Highlights: • The converters topology of series-parallel connection improves the power supply's performance. • The SOPC based on dual Nios II processors improves the real-time performance of system. • Pulse mode is implemented in digital power supply based on FPGA, with a smaller tracking error.

  1. Gene Editing: Powerful New Tools for Nephrology Research and Therapy.

    Science.gov (United States)

    Miyagi, Ayano; Lu, Aiwu; Humphreys, Benjamin D

    2016-10-01

    Biologic research is experiencing a transformation brought about by the ability of programmable nucleases to manipulate the genome. In the recently developed CRISPR/Cas system, short RNA sequences guide the endonuclease Cas9 to any location in the genome, causing a DNA double-strand break (DSB). Repair of DSBs allows the introduction of targeted genetic manipulations with high precision. Cas9-mediated gene editing is simple, scalable, and rapid, and it can be applied to virtually any organism. Here, we summarize the development of modern gene editing techniques and the biology of DSB repair on which these techniques are based. We discuss technical points in applying this technology and review its use in model organisms. Finally, we describe prospects for the use of gene editing to treat human genetic diseases. This technology offers tremendous promise for equipping the nephrology research community to better model and ultimately, treat kidney diseases.

  2. Military Medical Research in Support of National Instruments of Power

    Science.gov (United States)

    2009-03-26

    The USMHRP is conducting ongoing research in the identification, surveillance, and early warning for diseases like HIV/AIDS, malaria, and tuberculosis ...highly effective vaccines for yellow fever, meningococcal meningitis , encephalitis, and adenovirus caused respiratory disease – all deadly diseases...along with tuberculosis and malaria, and further illustrates the obligation of this kind of resources to support the NSS.44 The additional PEPFAR funding

  3. Parrot "Understands" Zero

    Science.gov (United States)

    Journal of College Science Teaching, 2005

    2005-01-01

    The walnut sized brain of the African grey parrot may actually be capable of comprehending abstract mathematical concepts. The bird seems to understand a numerical concept akin to zero--an abstract notion that humans don't typically understand until they are three or four years old. Alex, the 28-year-old parrot who lives in a Brandeis University…

  4. 旋转编码器找零安装装置研制%Research on Adjustment Device to Find Zero Position for Rotary Encoder

    Institute of Scientific and Technical Information of China (English)

    丁仕燕

    2013-01-01

    为了使旋转编码器安装时在零位,设计了找零位装置,该装置包括电子手轮、步进电机、蜗杆、斜齿轮和磁力表座组件.斜齿轮安装在旋转编码器的空心转轴上;磁力表座组件依靠磁铁吸力固定在自动化设备上,蜗杆安装在轴套中,该轴套被夹在磁力表座组件的弹性孔夹头中.电子手轮输出信号接入步进电机驱动器,步进电机跟随电子手轮转动进而驱动蜗杆转动,蜗杆驱动斜齿轮,进而驱动旋转编码器空心转轴;同时计算机读取旋转编码器输出信号以判断其是否在零位,如在零位,则立刻停止转动电子手轮.实验结果表明:利用该装置可方便、快捷地把旋转编码器安装在零位.%The adjustment device was designed in order that rotary encoder could be installed at zero position.The adjustment device was composed of a electronic handwheel,a step motor,a helical gear,a worm and a magnetic table block.The helical gear was installed on hollow shaft of rotary encoder,the magnetic table block was fixed on automated equipment by means of magnetic suction,the worm was installed in axle sleeve,which was clamped in elastic hole chuck of the magnetic table block.Output signals of the electronic handwheel was connected to step motor driver,the worm was driven by the step motor,which rotated following the electronic handwheel.The helical gear was driven by the worm,the hollow shaft of rotary encoder was driven by the helical gear.At the same time,output signals of the rotary encoder was read by software and used to judge whether the rotary encoder was at zero position.The rotation of the electronic handwheel was stopped immediately if the rotary encoder was at zero position.Experimental results show that the rotary encoder can be installed at zero position efficiently and easily with the adjustment device.

  5. Propulsion Investigation for Zero and Near-Zero Emissions Aircraft

    Science.gov (United States)

    Snyder, Christopher A.; Berton, Jeffrey J.; Brown, Gerald v.; Dolce, James L.; Dravid, Marayan V.; Eichenberg, Dennis J.; Freeh, Joshua E.; Gallo, Christopher A.; Jones, Scott M.; Kundu, Krishna P.; Marek, Cecil J.; Millis, Marc G.; Murthy, Pappu L.; Roach, Timothy M.; Smith, Timothy D.; Stefko, George L.; Sullivan, Roy M.; Tornabene, Robert T.; Geiselhat, Karl A.; Kascak, Albert F.

    2009-01-01

    As world emissions are further scrutinized to identify areas for improvement, aviation s contribution to the problem can no longer be ignored. Previous studies for zero or near-zero emissions aircraft suggest aircraft and propulsion system sizes that would perform propulsion system and subsystems layout and propellant tankage analyses to verify the weight-scaling relationships. These efforts could be used to identify and guide subsequent work on systems and subsystems to achieve viable aircraft system emissions goals. Previous work quickly focused these efforts on propulsion systems for 70- and 100-passenger aircraft. Propulsion systems modeled included hydrogen-fueled gas turbines and fuel cells; some preliminary estimates combined these two systems. Hydrogen gas-turbine engines, with advanced combustor technology, could realize significant reductions in nitrogen emissions. Hydrogen fuel cell propulsion systems were further laid out, and more detailed analysis identified systems needed and weight goals for a viable overall system weight. Results show significant, necessary reductions in overall weight, predominantly on the fuel cell stack, and power management and distribution subsystems to achieve reasonable overall aircraft sizes and weights. Preliminary conceptual analyses for a combination of gas-turbine and fuel cell systems were also performed, and further studies were recommended. Using gas-turbine engines combined with fuel cell systems can reduce the fuel cell propulsion system weight, but at higher fuel usage than using the fuel cell only.

  6. Steam turbine overspeed protection scheme after a sudden large -scale thermal power generating units outgoing transmission line interrupted based on zero power facility%零功率装置的发电机组外送线路中断后超速保护方案

    Institute of Scientific and Technical Information of China (English)

    余智

    2012-01-01

    Large - scale thermal power plant is in which output channel is break off, operational units will take place overspeed, even cause the equipment damaged. To avoid the accident happened , after analysis and discussion, considering using the way of zero power facility to generator triping , so as to ensure the safety outage of equipments.%大型火力发电厂在输出通道突然中断的情况下,运行的机组将会发生超速,甚至造成损坏,为避免此类事故的发生,经过分析论证,考虑采用零功率装置方式进行切机,以确保机组设备的安全停运。

  7. Cultivating the power of partnerships in feminist participatory action research in women's health.

    Science.gov (United States)

    Ponic, Pamela; Reid, Colleen; Frisby, Wendy

    2010-12-01

    Feminist participatory action research integrates feminist theories and participatory action research methods, often with the explicit intention of building community-academic partnerships to create new forms of knowledge to inform women's health. Despite the current pro-partnership agenda in health research and policy settings, a lack of attention has been paid to how to cultivate effective partnerships given limited resources, competing agendas, and inherent power differences. Based on our 10+ years individually and collectively conducting women's health and feminist participatory action research, we suggest that it is imperative to intentionally develop power-with strategies in order to avoid replicating the power imbalances that such projects seek to redress. By drawing on examples from three of our recent feminist participatory action projects we reflect on some of the tensions and complexities of attempting to cultivate power-with research partnerships. We then offer skills and resources needed by academic researchers to effectively harness the collective resources, agendas, and knowledge that each partner brings to the table. We suggest that investing in the process of cultivating power-with research partnerships ultimately improves our collective ability to understand and address women's health issues.

  8. Commercial Research and Development: Power to Explore, Opportunities from Discovery

    Science.gov (United States)

    Casas, Joseph C.; Nall, Mark; Powers, C. Blake; Henderson, Robin N. (Technical Monitor)

    2002-01-01

    The technical and economic goals of commercial use of space are laudable, and are addressed as a high priority by almost every national space program and most major aerospace companies the world over. Yet, the focus of most organizational agendas and discussions tends to focus on one or two very narrow enabling aspects of this potentially large technological and economic opportunity. While government sponsored commercial launch activities and private space platforms are an integral part of efforts to leverage the commercial use of space, these activities are possibly one of the smallest parts of creating, a viable and sustainable market for the commercial use of space. Most of the current programs usually do not appropriately address some of the critical issues of the current, already interested, potential space user communities. Current programs place the focus of the majority of the user requirements on the vehicle payload weight and mass performance considerations as the primary payload economical factor in providing a commercial market with a stimulating price for gaining access to the space environment. The larger user challenges of transformation from Earth-based research and development approaches to space environment approaches are not addressed early enough in programs to impact the new business considerations of potential users. Currently, space-based research and development user activities require a large user investment in time, in development of new areas of support expertise, in development of new systems, in risk of schedule to completion, and in long term capital positioning. The larger opportunities for stimulating a strong market driven interest in commercial use of space that could result from the development of vehicle payload "leap ahead technologies" for users are being missed, and there is a real risk of limiting the potentially broader market base to support a more technologically advanced and economically lucrative outcome. A major driving

  9. Research on magnetic integrated for zero-current quasi-resonant buck converter%零电流准谐振Buck变换器的磁集成研究

    Institute of Scientific and Technical Information of China (English)

    陈正一; 杨玉岗; 李洪珠

    2011-01-01

    Taking Buck converter as an example,the resonant inductor and resonant capacitor were introduced, which constituted the resonant switch with the converter power switch. Through the resonance,the waveform of current through the power switch became sinusoidal,which created zero-current switching condition for power switch. In this paper, the discrete resonant inductor and filter inductor were integrated to integration magnetic, and the principle of integration Buck converter works was described. The integration of circuit was simulated by Saber software, and the effect of coupling coefficient of the resonant inductor and filter inductor on the resonant frequency and output voltage was analyzed. The loosely coupled and tightly coupled integration approach Was applied to design a ZCS Buck converter,and the zero-current turn-on and zero-current turn-off of power switch was achieved, and was authenticated by saber.%以零电流准谐振Buck变换器为例,引入谐振电感和谐振电容与变换器中的功率开关管组成谐振开关.通过谐振,使流过功率开关管的电流呈正弦波形,为功率开关管创造了零电流开关条件.对分立的谐振电感和滤波电感进行磁集成,阐述集成后Buck变换器工作原理.用Saber软件对集成后的电路进行仿真.分析谐振电感和滤波电感的耦合系数对谐振频率和输出电压的影响.最后采用松耦合和紧耦合两种集成方法设计了一台零电流准谐振Buck变换器,通过Saber软件仿真验证功率开关管实现了零电流开通和零电流关断.

  10. Causality in Statistical Power: Isomorphic Properties of Measurement, Research Design, Effect Size, and Sample Size

    Science.gov (United States)

    Heidel, R. Eric

    2016-01-01

    Statistical power is the ability to detect a significant effect, given that the effect actually exists in a population. Like most statistical concepts, statistical power tends to induce cognitive dissonance in hepatology researchers. However, planning for statistical power by an a priori sample size calculation is of paramount importance when designing a research study. There are five specific empirical components that make up an a priori sample size calculation: the scale of measurement of the outcome, the research design, the magnitude of the effect size, the variance of the effect size, and the sample size. A framework grounded in the phenomenon of isomorphism, or interdependencies amongst different constructs with similar forms, will be presented to understand the isomorphic effects of decisions made on each of the five aforementioned components of statistical power. PMID:27073717

  11. Causality in Statistical Power: Isomorphic Properties of Measurement, Research Design, Effect Size, and Sample Size

    Directory of Open Access Journals (Sweden)

    R. Eric Heidel

    2016-01-01

    Full Text Available Statistical power is the ability to detect a significant effect, given that the effect actually exists in a population. Like most statistical concepts, statistical power tends to induce cognitive dissonance in hepatology researchers. However, planning for statistical power by an a priori sample size calculation is of paramount importance when designing a research study. There are five specific empirical components that make up an a priori sample size calculation: the scale of measurement of the outcome, the research design, the magnitude of the effect size, the variance of the effect size, and the sample size. A framework grounded in the phenomenon of isomorphism, or interdependencies amongst different constructs with similar forms, will be presented to understand the isomorphic effects of decisions made on each of the five aforementioned components of statistical power.

  12. Experimental researches on power plant condensers performed at ENEA laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Fabrizi, F.; Girardi, G.; Palazzi, G. [ENEA, Casaccia (Italy). Area Energetica

    1993-09-01

    Improvement of Italian industrial design capability is the principal aim of the ENEA (Italian Agency for Energy, New Technologies and the Environment) R&D program which is studying the thermo-hydraulic aspects of shell-and-tube condensers. The principal experimental apparatus of this project allows researchers to perform tests for investigating in detail feed-water heater (FWH) thermo-hydraulic performance. A scaled-down test section was used in significant size to reproduce condensing, de-superheating and drain cooling zones. To approach condensation phenomena occurring in the FWH, a visualization test section was also built. A new model for condensation flow, perpendicular to the tubes, was developed using the films shot through the visualization test section. All the experimental data carried out in the program were used to assess an original code, named COND. Concerning the tube-side condenser design, an analysis of the velocity field in the front end head was performed to minimize erosion phenomena.

  13. A neutron tomography facility at a low power research reactor

    CERN Document Server

    Körner, S; Von Tobel, P; Rauch, H

    2001-01-01

    Neutron radiography (NR) provides a very efficient tool in the field of non-destructive testing as well as for many applications in fundamental research. A neutron beam penetrating a specimen is attenuated by the sample material and detected by a two-dimensional (2D) imaging device. The image contains information about materials and structure inside the sample because neutrons are attenuated according to the basic law of radiation attenuation. Contrary to X-rays, neutrons can be attenuated by some light materials, as for example, hydrogen and boron, but penetrate many heavy materials. Therefore, NR can yield important information not obtainable by more traditional methods. Nevertheless, there are many aspects of structure, both quantitative and qualitative, that are not accessible from 2D transmission images. Hence, there is an interest in three-dimensional neutron imaging. At the 250 kW TRIGA Mark II reactor of the Atominstitut in Austria a neutron tomography facility has been installed. The neutron flux at ...

  14. ANL Technical Support Program for DOE Environmental Restoration and Waste Management; Annual report, October 1992--September 1993

    Energy Technology Data Exchange (ETDEWEB)

    Bates, J.K.; Bourcier, W.L.; Bradley, C.R. [and others

    1994-06-01

    This report is an overview of the progress during FY 1993 for the Technical Support Program that is part of the ANL Technology Support Activity for DOE Environmental Restoration and Waste Management (EM). The purpose is to evaluate, before hot start-up of the Defense Waste Processing Facility (DWPF) and the West Valley Demonstration Project (WVDP), factors that are anticipated to affect glass reaction in an unsaturated environment typical of what may be expected for the candidate Yucca Mountain repository site. Specific goals for the testing program include the following: reviewing and evaluating available data on parameters that will be important in establishing the long-term performance of glass in a repository environment; performing tests to further quantify the effects of important variables where there are deficiencies in the available data; and initiating long-term tests to determine glass performance under a range of conditions applicable to repository disposal.

  15. Argillization mechanics of rock from the Xing'anling Group in the Beier depression of the Hailar basin

    Institute of Scientific and Technical Information of China (English)

    LIU Qin-fu; FU Zheng; YANG Bao-quan

    2008-01-01

    The reservoir of the Xing'anling Group in the Beier depression of the Hailar basin is loosely cemented with many tuffaceous grains. This causes argillization and collapse of the grain framework of the reservoir sandstones. A detailed study on the characteristics of rocks and minerals was carded out through polarized microscope, X-ray diffraction, X-ray fluorescence, SEM and energy spectrum analysis. The results indicate that the reason for argillization is the abundant pyroclastic, and especially tuffaceous, grains in the reservoir. The alkaline component is relatively high in some strata. These are easily altered to montmorillonite in diagenesis. Na+ montmorillonite swells strongly when exposed to water. This is the fundamental reason for the reservoir's argillization and plugging.

  16. ANL Technical Support Program for DOE Environmental Restoration and Waste Management. Annual report, October 1990--September 1991

    Energy Technology Data Exchange (ETDEWEB)

    Bates, J.K.; Bradley, C.R.; Buck, E.C.; Cunnane, J.C.; Dietz, N.L.; Ebert, W.L.; Emery, J.W.; Feng, X.; Gerding, T.J.; Gong, M.; Hoh, J.C.; Mazer, J.J.; Wronkiewicz, D.J. [Argonne National Lab., IL (United States); Bourcier, W.L.; Morgan, L.E.; Nielsen, J.K.; Steward, S.A. [Lawrence Livermore National Lab., CA (United States); Ewing, R.C.; Wang, L.M. [New Mexico Univ., Albuquerque, NM (United States); Han, W.T.; Tomozawa, M. [Rensselaer Polytechnic Inst., Troy, MI (United States)

    1992-03-01

    This report provides an overview of progress during FY 1991 for the Technical Support Program that is part of the ANL Technology Support Activity for DOE, Environmental Restoration and Waste Management (EM). The purpose is to evaluate, before hot start-up of the Defenses Waste Processing Facility (DWPF) and the West Valley Demonstration Project (WVDP), factors that are likely to affect glass reaction in an unsaturated environment typical of what may be expected for the candidate Yucca Mountain repository site. Specific goals for the testing program include the following: (1) to review and evaluate available information on parameters that will be important in establishing the long-term performance of glass in a repository environment; (2) to perform testing to further quantify the effects of important variables where there are deficiencies in the available data; and (3) to initiate long-term testing that will bound glass performance under a range of conditions applicable to repository disposal.

  17. Unique Power Electronics and Drives Experimental Bench (PEDEB) to Facilitate Learning and Research

    Science.gov (United States)

    Anand, S.; Farswan, R. S.; Fernandes, B. G.

    2012-01-01

    Experimentation is important for learning and research in the field of power electronics and drives. However, a great deal of equipment is required to study the various topologies, controllers, and functionalities. Thus, the cost of establishing good laboratories and research centers is high. To address this problem, the authors have developed a…

  18. Beyond "on" or "with": Questioning Power Dynamics and Knowledge Production in "Child-Oriented" Research Methodology

    Science.gov (United States)

    Hunleth, Jean

    2011-01-01

    By taking a reflexive approach to research methodology, this article contributes to discussions on power dynamics and knowledge production in the social studies of children. The author describes and analyzes three research methods that she used with children--drawing, child-led tape-recording and focus group discussions. These methods were carried…

  19. Research Design and the Predictive Power of Measures of Self-Efficacy

    Science.gov (United States)

    Moriarty, Beverley

    2014-01-01

    The purpose of this enquiry was to examine how research design impacts on the predictive power of measures of self-efficacy. Three cautions for designing research into self-efficacy drawn from the seminal work of Albert Bandura (1986) and a further caution proposed by the current author together form the analytical framework for this enquiry. For…

  20. Zero leakage sealings

    Science.gov (United States)

    Kotesovec, Bernhard; Steinrück, Herbert

    2010-11-01

    The piston rod of a reciprocating compressor is sealed with elastic cylindrical sealing elements. Across the sealings the pressure drops from the operating pressure to the ambient pressure. The lubrication gap between the elastic sealing and reciprocating piston rod is studied with the aim to find conditions of a leakage free sealing. The flow in the lubrication gap and the elastic deformation of the sealing are determined simultaneously. The net-flow during one cycle of the reciprocating piston rod is calculated. It turns out that maintaining zero leakage is very sensible. Indeed the outbound flow during out-stroke has to be equal the inbound flow during the in-stroke. By prescribing a special shape of the undeformed sealing zero leakage can be attained - at least theoretically for certain operating conditions. It turns out that temperature dependent material data and a model for cavitation is necessary. The model, its numerical implementation and results will be discussed.

  1. Net Zero Energy Buildings

    DEFF Research Database (Denmark)

    Marszal, Anna Joanna; Bourrelle, Julien S.; Musall, Eike

    2010-01-01

    The international cooperation project IEA SHC Task 40 / ECBCS Annex 52 “Towards Net Zero Energy Solar Buildings”, attempts to develop a common understanding and to set up the basis for an international definition framework of Net Zero Energy Buildings (Net ZEBs). The understanding of such buildings...... and how the Net ZEB status should be calculated differs in most countries. This paper presents an overview of Net ZEBs energy calculation methodologies proposed by organisations representing eight different countries: Austria, Canada, Denmark, Germany, Italy, Norway, Switzerland and the USA. The different...... parameters used in the calculations are discussed and the various renewable supply options considered in the methodologies are summarised graphically. Thus, the paper helps to understand different existing approaches to calculate energy balance in Net ZEBs, highlights the importance of variables selection...

  2. Data Linkage: A powerful research tool with potential problems

    Directory of Open Access Journals (Sweden)

    Scott Ian

    2010-12-01

    Full Text Available Abstract Background Policy makers, clinicians and researchers are demonstrating increasing interest in using data linked from multiple sources to support measurement of clinical performance and patient health outcomes. However, the utility of data linkage may be compromised by sub-optimal or incomplete linkage, leading to systematic bias. In this study, we synthesize the evidence identifying participant or population characteristics that can influence the validity and completeness of data linkage and may be associated with systematic bias in reported outcomes. Methods A narrative review, using structured search methods was undertaken. Key words "data linkage" and Mesh term "medical record linkage" were applied to Medline, EMBASE and CINAHL databases between 1991 and 2007. Abstract inclusion criteria were; the article attempted an empirical evaluation of methodological issues relating to data linkage and reported on patient characteristics, the study design included analysis of matched versus unmatched records, and the report was in English. Included articles were grouped thematically according to patient characteristics that were compared between matched and unmatched records. Results The search identified 1810 articles of which 33 (1.8% met inclusion criteria. There was marked heterogeneity in study methods and factors investigated. Characteristics that were unevenly distributed among matched and unmatched records were; age (72% of studies, sex (50% of studies, race (64% of studies, geographical/hospital site (93% of studies, socio-economic status (82% of studies and health status (72% of studies. Conclusion A number of relevant patient or population factors may be associated with incomplete data linkage resulting in systematic bias in reported clinical outcomes. Readers should consider these factors in interpreting the reported results of data linkage studies.

  3. Stibine/arsine monitoring during EV operation: summary report on preliminary tests at ANL and at LILCO

    Energy Technology Data Exchange (ETDEWEB)

    Loutfy, R.O.; Graczyk, D.G.; Varma, R.; Hayes, E.R.; Williams, F.L.; Yao, N.P.

    1981-02-01

    A series of tests was performed to monitor the evolution and dispersal of stibine and arsine from the lead-acid propulsion batteries in three different Electra-Van Model 600 vehicles operated by Argonne National Laboratory (ANL) and by the Long Island Lighting Company (LILCO). Ambient air was sampled at several locations inside the vehicles and in the garages where testing was done during charge, equalization charge, and on-the-road discharge operations. In addition, direct sampling of cell off-gases was performed with the ANL van. Interpretation of the individual test results was carried out in the context of vehicle characteristics, sampling protocol, and operating conditions. The test results demonstrated that under the test conditions only small concentrations of stibine and arsine accumulated in occupiable work areas. Measured concentrations in the vehicles and in the garages never exceeded 25% of the Threshold Limit Value-Time Weighted Average (TLV-TWA) standards. A threshold voltage for hydride production, at about 2.45 V per cell, was reflected in the results of the experiments performed during charging of the batteries. Hydride evolution rates were lower during equalization charge than during the overcharge portion of a charge cycle when the on-board charger was used in a normal operating mode. A delayed release of the metal hydrides from the battery cells was observed during on-the-road operation of the vehicles. The implications of these observations for electric vehicle (EV) operation are discussed. An engineering analysis of the generation and dispersal of the metal hydrides is presented, and equations are derived for estimating minimum ventilation requirements for the EV battery compartment and for garages housing EV operations. Recommendations are made regarding safe handling procedures for battery off-gases, procedures for conducting stibine/arsine monitoring tests and future work.

  4. Solar Power and Solar Fuels Synthesis Report. Technology, market and research activities 2006-2011

    Energy Technology Data Exchange (ETDEWEB)

    Ridell, Bengt; Nilsson, Ronny; Rehnlund, Bjoern [Grontmij, Stockholm (Sweden); Kasemo, Bengt [Chalmers Univ. of Technology, Goeteborg (Sweden)

    2012-11-01

    The objectives of the synthesis is to survey the situation and give an accumulated and concentrated knowledge about status, needs and opportunities for Swedish research and Swedish industry within the area of solar power and solar fuels, to be used for prioritisation of further efforts. The synthesis shall identify strengths and weaknesses in areas fundamental for development of solar power and solar fuels, focused on the development in Sweden, but in an international context. The synthesis shall also cover proposals for future Swedish research efforts and organisation of future Swedish research programs.

  5. Army Net Zero Prove Out. Net Zero Waster Best Practices

    Science.gov (United States)

    2014-11-18

    Colorado • Fort Bliss, Texas These sites served as test beds for the Army’s Net Zero Initiative, specifically, Net Zero Water , and the Army provided...have sustainability, energy efficiency, water conservation, recycling, pollution prevention, and green procurement programs in place that they can...ARMY NET ZERO PROVE OUT Final Net Zero Water Best Practices November 18, 2014 Distribution A Approved for public release

  6. Renewable energy research 1995–2009: a case study of wind power research in EU, Spain, Germany and Denmark

    DEFF Research Database (Denmark)

    Sanz-Casado, Elias; Garcia- Zorita, J. Carlos; Serrano-López, Antonio Eleazar;

    2013-01-01

    The paper reports the developments and citation patterns over three time periods of research on Renewable Energy generation and Wind Power 1995–2011 in EU, Spain, Germany and Denmark. Analyses are based on Web of Science and incorporate journal articles as well as conference proceeding papers...

  7. Researching the Transnational Higher Education Policy Landscape: Exploring Network Power and Dissensus in a Globalising System

    OpenAIRE

    Caruana, V

    2016-01-01

    This article reviews research on transnational higher education (TNHE) published in academic journals between 2006 and 2014 through the lenses of network power and dissensus. Conclusions suggest the need for more research on the ‘entrapping’ aspects of global social relations to provide a counterweight to the influence of dominant paradigms. It is argued that research at local-institutional level, harnessing the dissensus of the academic community with the needs and aspirations of students pr...

  8. Research of Zero-Crossing Detection for Sensorless Brushless DC Based on DSC%基于DSC的无刷直流电动机过零检测方法

    Institute of Scientific and Technical Information of China (English)

    朱乐乐; 王宜怀; 胡玉鑫; 王浩

    2013-01-01

    The key technology of sensorless brushless DC motor control is zero-crossing detection. Based on full research and analysis of the hack-EMF motor principle,wave and traditional detection methods,a new method of back-EMF zero-crossing detection was introduced. The method did not rigidly adhere to the principles of traditional back-EMF zero-crossing detection, and the motor midpoint, depth filter and voltage comparison circuits in the design of the traditional zero-crossing detection circuit were rejected. The commutation points were received by realizing three-phase voltage real time collection,filtering and designing the effective software algorithms. The method was applied in the electric car control system. The experiment result shows that the method has some advantages which are simple zero-crossing detection circuits, software with clear structure and good real-time and so on.%无位置传感器无刷直流电动机的过零检测是该类型电机控制的关键技术.在充分研究与分析该类电机的反电动势原理、波形及传统检测方法的基础上,提出了一种反电动势过零检测新方法.该方法不拘泥于传统反电动势过零检测原理,摈弃了传统过零检测电路设计中的电机中点、深度滤波及电压比较等电路,利用DSC实现三相端电压动态实时采集、滤波,并设计有效的软件算法,得到换相点.实际应用结果表明,该过零检测电路具有实现简洁、软件结构清晰及实时性好等优点.

  9. Development of power storage system. Advanced battery power storage system. (The development results and research plan in 1988 fiscal year)

    Energy Technology Data Exchange (ETDEWEB)

    Kouda, Atsushi; Yazawa, Tetsuo

    1988-07-01

    The research and trial manufacture of 1kW battery on the electrode and battery construction, development of 10kW battery module, capacity enlarging and trial manufacturing as to four type batteries, that is, Na-S battery, Zn-Cl battery, Zn-Br battery and redox flow type battery were forwarded as the items to be developed in Japan for the advanced battery power storage system. The research and development of system technology was started in 1980 to verify the operating and controlling characteristics and the protection system. The technology of the 60kW class module for 1,000kW class battery system was established in 1987 and the total system research and development is forwarding. The 1,000kW class system test is continued; the 60kW class module batteries of Na-S battery and Zn-Br battery are operated; the fabrication of 1,000kW class pilot plant is initiated; and the reliability and safety of the power system are verified in 1988. (1 fig, 2 tabs)

  10. Design of a Glenn Research Center Solar Field Grid-Tied Photovoltaic Power System

    Science.gov (United States)

    Eichenberg, Dennis J.

    2009-01-01

    The NASA Glenn Research Center (GRC) designed, developed, and installed, a 37.5 kW DC photovoltaic (PV) Solar Field in the GRC West Area in the 1970s for the purpose of testing PV panels for various space and terrestrial applications. The PV panels are arranged to provide a nominal 120 VDC. The GRC Solar Field has been extremely successful in meeting its mission. The PV panels and the supporting electrical systems are all near their end of life. GRC has designed a 72 kW DC grid-tied PV power system to replace the existing GRC West Area Solar Field. The 72 kW DC grid-tied PV power system will provide DC solar power for GRC PV testing applications, and provide AC facility power for all times that research power is not required. A grid-tied system is connected directly to the utility distribution grid. Facility power can be obtained from the utility system as normal. The PV system is synchronized with the utility system to provide power for the facility, and excess power is provided to the utility for use by all. The project transfers space technology to terrestrial use via nontraditional partners. GRC personnel glean valuable experience with PV power systems that are directly applicable to various space power systems, and provide valuable space program test data. PV power systems help to reduce harmful emissions and reduce the Nation s dependence on fossil fuels. Power generated by the PV system reduces the GRC utility demand, and the surplus power aids the community. Present global energy concerns reinforce the need for the development of alternative energy systems. Modern PV panels are readily available, reliable, efficient, and economical with a life expectancy of at least 25 years. Modern electronics has been the enabling technology behind grid-tied power systems, making them safe, reliable, efficient, and economical with a life expectancy of at least 25 years. The report concludes that the GRC West Area grid-tied PV power system design is viable for a reliable

  11. Quantum statistical zero-knowledge

    OpenAIRE

    2002-01-01

    In this paper we propose a definition for (honest verifier) quantum statistical zero-knowledge interactive proof systems and study the resulting complexity class, which we denote QSZK. We prove several facts regarding this class that establish close connections between classical statistical zero-knowledge and our definition for quantum statistical zero-knowledge, and give some insight regarding the effect of this zero-knowledge restriction on quantum interactive proof systems.

  12. Research of Characteristics of the Low Voltage Power Line in Underground Coal Mine

    Science.gov (United States)

    Wei, Shaoliang; Qin, Shiqun; Gao, Wenchang; Cheng, Fengyu; Cao, Zhongyue

    The power line communications (PLCs) can count on existing electrical connections reaching each corner in the locations where such applications are required, so signal transmission over power lines is nowadays gaining more and more interest for applications like internet. The research of characteristics of the low voltage power line is the fundamental and importance task. This work presents a device to test the characteristics of the low voltage power line. The low voltage power line channel characteristics overground and the channel characteristics underground were tested in using this device. Experiments show that, the characteristics are different between the PLCs channel underground coal mine and the PLC channel overground. Different technology should be adopted to structure the PLCs channel model underground coal mine and transmit high speed digital signal. But how to use the technology better to the high-speed digital communication under coal mine is worth of further studying.

  13. Strongly Zero-Dimensional Locales

    Institute of Scientific and Technical Information of China (English)

    KOU Hui; LUO Mao Kang

    2002-01-01

    New kinds of strongly zero-dimensional locales are introduced and characterized, whichare different from Johnstone's, and almost all the topological properties for strongly zero-dimensionalspaces have the pointless localic forms. Particularly, the Stone-Cech compactification of a stronglyzero-dimensional locale is stongly zero-dimensional.

  14. A critical discussion of null hypothesis significance testing and statistical power analysis within psychological research

    DEFF Research Database (Denmark)

    Jones, Allan; Sommerlund, Bo

    2007-01-01

    The uses of null hypothesis significance testing (NHST) and statistical power analysis within psychological research are critically discussed. The article looks at the problems of relying solely on NHST when dealing with small and large sample sizes. The use of power-analysis in estimating...... the potential error introduced by small and large samples is advocated. Power analysis is not recommended as a replacement to NHST but as an additional source of information about the phenomena under investigation. Moreover, the importance of conceptual analysis in relation to statistical analysis of hypothesis...

  15. Research on the Defects Restraining Ability of Power Supply Transacting Electrocircuit

    Institute of Scientific and Technical Information of China (English)

    GAO Jun; CHEN Chuan-bo

    2006-01-01

    Adopting the mechanism model and the system identification method, the power supply transacting electrocircuit (integrate manostat) is analyzed, and the restraining ability and the response for power supply transacting electrocircuit to overcome various battery defects are studied. The effects of the power supply yawp on the normal functions of the radio fuze are investigated. The research indicate that the shortcomings of the integration manostat as battery defects can be regarded as steady noise, and the restraining ability of the integration manostat to battery defects isn't less than 50 dB.

  16. The EU as a Normative Power and the Research on External Perceptions: the Missing Link

    DEFF Research Database (Denmark)

    Larsen, Henrik

    2014-01-01

    perception offer some findings that are central for the NPE debate. This article’s argument is that the external perceptions literature points to a limited (if still identifiable) perception of the EU as a normative power depending on the geographical area. By comparison, the image of a powerful economic......In research on European foreign policy two important axes of debate have been running relatively independently of each other for more than a decade: the study of the European Union as a normative power (NPE) and the study of external perceptions of the EU. However, the studies of external...

  17. Initial Critical Experiment and Zero Power Physical Experiments of YBW Critical Assembly after Technical Modification%YBW 临界装置技术改造后的首次临界试验和零功率物理试验

    Institute of Scientific and Technical Information of China (English)

    黄礼渊; 牛江; 付国恩; 魏东; 穆克亮

    2014-01-01

    It reports the initial critical experiment ,zero power physical experiments and the experimental results on YBW Critical Assembly after technical modification .The experiments show that the modified systems and de-vices of YBW Critical Assembly can perform their own functions , the protection system and reactivity control system satisfy the requirements , the reactor can operate safely , and the Assembly can be used for the reactor physical experiment researches .%报告了技术改造后的YBW临界装置首次临界试验和零功率物理试验及试验结果。试验表明:技术改造后,YBW临界装置的系统和设备能正常执行其功能,保护系统和堆芯反应性控制系统等符合设计要求,反应堆能够安全地正常运行。该装置可以用于开展反应堆物理实验研究。

  18. NRC Job Code V6060: Extended in-situ and real time monitoring. Task 4: Detection and monitoring of leaks at nuclear power plants external to structures

    Energy Technology Data Exchange (ETDEWEB)

    Sheen, S. H. (Nuclear Engineering Division)

    2012-08-01

    In support of Task 4 of the NRC study on compliance with 10 CFR part 20.1406, minimization of contamination, Argonne National Laboratory (ANL) conducted a one-year scoping study, in concert with a parallel study performed by NRC/NRR staff, on monitoring for leaks at nuclear power plants (NPPs) external to structures. The objective of this task-4 study is to identify and assess those sensors and monitoring techniques for early detection of abnormal radioactive releases from the engineered facility structures, systems and components (SSCs) to the surrounding underground environment in existing NPPs and planned new reactors. As such, methods of interest include: (1) detection of anomalous water content of soils surrounding SSCs, (2) radionuclides contained in the leaking water, and (3) secondary signals such as temperature. ANL work scope includes mainly to (1) identify, in concert with the nuclear industry, the sensors and techniques that have most promise to detect radionuclides and/or associated chemical releases from SSCs of existing NPPs and (2) review and provide comments on the results of the NRC/NRR staff scoping study to identify candidate technologies. This report constitutes the ANL deliverable of the task-4 study. It covers a survey of sensor technologies and leak detection methods currently applied to leak monitoring at NPPs. The survey also provides a technology evaluation that identifies their strength and deficiency based on their detection speed, sensitivity, range and reliability. Emerging advanced technologies that are potentially capable of locating releases, identifying the radionuclides, and estimating their concentrations and distributions are also included in the report along with suggestions of required further research and development.

  19. Development and Testing of the Glenn Research Center Visitor's Center Grid-Tied Photovoltaic Power System

    Science.gov (United States)

    Eichenberg, Dennis J.

    2009-01-01

    The NASA Glenn Research Center (GRC) has developed, installed, and tested a 12 kW DC grid-tied photovoltaic (PV) power system at the GRC Visitor s Center. This system utilizes a unique ballast type roof mount for installing the photovoltaic panels on the roof of the Visitor s Center with no alterations or penetrations to the roof. The PV system has generated in excess of 15000 kWh since operation commenced in August 2008. The PV system is providing power to the GRC grid for use by all. Operation of the GRC Visitor s Center PV system has been completely trouble free. A grid-tied PV power system is connected directly to the utility distribution grid. Facility power can be obtained from the utility system as normal. The PV system is synchronized with the utility system to provide power for the facility, and excess power is provided to the utility. The project transfers space technology to terrestrial use via nontraditional partners. GRC personnel glean valuable experience with PV power systems that are directly applicable to various space power systems, and provides valuable space program test data. PV power systems help to reduce harmful emissions and reduce the Nation s dependence on fossil fuels. Power generated by the PV system reduces the GRC utility demand, and the surplus power aids the community. Present global energy concerns reinforce the need for the development of alternative energy systems. Modern PV panels are readily available, reliable, efficient, and economical with a life expectancy of at least 25 years. Modern electronics has been the enabling technology behind grid-tied power systems, making them safe, reliable, efficient, and economical with a life expectancy of at least 25 years. Based upon the success of the GRC Visitor s Center PV system, additional PV power system expansion at GRC is under consideration. The GRC Visitor s Center grid-tied PV power system was successfully designed and developed which served to validate the basic principles

  20. Experiment of Doppler Heating Starting Point Measurement for Zero Power Physical Test in the Nuclear Power Reactor%核动力反应堆零功率物理试验的多普勒发热点测量试验

    Institute of Scientific and Technical Information of China (English)

    黄礼渊; 付国恩

    2015-01-01

    In order to determine the upper limit of power,calibrate the range of power and assure testing accura-cy,Doppler heating starting point is measured using digital reactivity meter during zero power physical experi-ment in the reactor.The paper describes the experimental theory,instrument,methods,results and data process-ing methods.The experimental results show that Doppler heating starting point can be determined by modified reactivity values measured by digital reactivity meter.The experience can be used in the following physical ex-periment.%为了定量确定零功率物理试验功率的上限,在反应堆零功率物理试验中,利用数字反应性仪测量多普勒发热点,以确定试验功率的范围、保证试验精度。叙述了本次多普勒发热点测量试验的原理、试验仪器、试验方法、试验结果及数据处理方法等,试验结果表明:利用数字反应性仪测得的反应性经过修正后可以准确地判断多普勒发热点,可为后续物理试验提供参考。

  1. SAFIR2014. The Finnish Research Programme on Nuclear Power Plant Safety 2011-2014. Interim Report

    Energy Technology Data Exchange (ETDEWEB)

    Simola, K. (ed.)

    2013-02-15

    The Finnish Nuclear Power Plant Safety Research Programme 2011-2014, SAFIR2014, is a 4-year publicly funded national technical and scientific research programme on the safety of nuclear power plants. The programme is funded by the State Nuclear Waste Management Fund (VYR), as well as other key organisations operating in the area of nuclear energy. The programme provides the necessary conditions for retaining knowledge needed for ensuring the continuance of safe use of nuclear power, for developing new know-how and for participation in international co-operation. The SAFIR2014 Steering Group, responsible of the strategic alignements of the programme, consists of representatives of the Finnish Nuclear Safety Authority (STUK), Ministry of Employment and the Economy (MEE), Technical Research Centre of Finland (VTT), Teollisuuden Voima Oyj (TVO), Fortum Power and Heat Oy (Fortum), Fennovoima Oy, Lappeenranta University of Technology (LUT), Aalto University (Aalto), Finnish Funding Agency for Technology and Innovation (Tekes), Finnish Institute of Occupational Health (TTL) and the Swedish Radiation Safety Authority (SSM). The research programme is divided into nine areas: Man, organisation and society, Automation and control room, Fuel research and reactor analysis, Thermal hydraulics, Severe accidents, Structural safety of reactor circuits, Construction safety, Probabilistic risk analysis (PRA), and Development of research infrastructure. A reference group is assigned to each of these areas to respond for the strategic planning and to supervise the projects in its respective field. Research projects are selected annually based on a public call for proposals. Most of the projects are planned for the entire duration of the programme, but there can also be shorter one- or two-year projects. The annual volume of the SAFIR2014 programme in 2011-2012 has been 9,5-9,9 M euro. Main funding organisations were the State Nuclear Waste Management Fund (VYR) with over 5 M euro and

  2. Surface Charging and Points of Zero Charge

    CERN Document Server

    Kosmulski, Marek

    2009-01-01

    Presents Points of Zero Charge data on well-defined specimen of materials sorted by trademark, manufacturer, and location. This text emphasizes the comparison between particular results obtained for different portions of the same or very similar material and synthesizes the information published in research reports over the past few decades

  3. Research on Discharge Circuit of Electro-Hydraulic Power Impulse Water Jets

    Science.gov (United States)

    Wang, Zhaohui; Gao, Quanjie; Wang, Wei; Liao, Zhenfang

    2012-01-01

    Electro-hydraulic power impulse water jets can convert the shock wave generated in the liquid by discharging into mechanical energy, and it has been widely used in material forming, surface cleaning, pipeline dirt cleaning and ore breaking process. Compared with the traditional high pressure water jets, the energy utilization of electro-hydraulic power impulse water jets is up to 80% while the water consumption is reduced by 40-55%. This paper has taken electro-hydraulic power impulse water jets as the research object, employed obtaining the maximum pressure of compression impulse matrix surface as the research goal, studied in depth the equivalent discharge circuit, characteristic equation and the relationship between the electrical parameters of the electro-hydraulic power impulse discharge circuit and built the calculation method of the voltage, the inductance, the capacitance and the electrode spacing parameter of electro-hydraulic power impulse water jets discharge circuit. So, it will provide important theoretical basis for further studies of electro-hydraulic power impulse technology and the existing water jets device.

  4. Zero Temperature Hope Calculations

    Energy Technology Data Exchange (ETDEWEB)

    Rozsnyai, B F

    2002-07-26

    The primary purpose of the HOPE code is to calculate opacities over a wide temperature and density range. It can also produce equation of state (EOS) data. Since the experimental data at the high temperature region are scarce, comparisons of predictions with the ample zero temperature data provide a valuable physics check of the code. In this report we show a selected few examples across the periodic table. Below we give a brief general information about the physics of the HOPE code. The HOPE code is an ''average atom'' (AA) Dirac-Slater self-consistent code. The AA label in the case of finite temperature means that the one-electron levels are populated according to the Fermi statistics, at zero temperature it means that the ''aufbau'' principle works, i.e. no a priory electronic configuration is set, although it can be done. As such, it is a one-particle model (any Hartree-Fock model is a one particle model). The code is an ''ion-sphere'' model, meaning that the atom under investigation is neutral within the ion-sphere radius. Furthermore, the boundary conditions for the bound states are also set at the ion-sphere radius, which distinguishes the code from the INFERNO, OPAL and STA codes. Once the self-consistent AA state is obtained, the code proceeds to generate many-electron configurations and proceeds to calculate photoabsorption in the ''detailed configuration accounting'' (DCA) scheme. However, this last feature is meaningless at zero temperature. There is one important feature in the HOPE code which should be noted; any self-consistent model is self-consistent in the space of the occupied orbitals. The unoccupied orbitals, where electrons are lifted via photoexcitation, are unphysical. The rigorous way to deal with that problem is to carry out complete self-consistent calculations both in the initial and final states connecting photoexcitations, an enormous computational task

  5. A survey of noninteractive zero knowledge proof system and its applications.

    Science.gov (United States)

    Wu, Huixin; Wang, Feng

    2014-01-01

    Zero knowledge proof system which has received extensive attention since it was proposed is an important branch of cryptography and computational complexity theory. Thereinto, noninteractive zero knowledge proof system contains only one message sent by the prover to the verifier. It is widely used in the construction of various types of cryptographic protocols and cryptographic algorithms because of its good privacy, authentication, and lower interactive complexity. This paper reviews and analyzes the basic principles of noninteractive zero knowledge proof system, and summarizes the research progress achieved by noninteractive zero knowledge proof system on the following aspects: the definition and related models of noninteractive zero knowledge proof system, noninteractive zero knowledge proof system of NP problems, noninteractive statistical and perfect zero knowledge, the connection between noninteractive zero knowledge proof system, interactive zero knowledge proof system, and zap, and the specific applications of noninteractive zero knowledge proof system. This paper also points out the future research directions.

  6. State-of-the-art research: optimal investment in market-based electric power systems

    Energy Technology Data Exchange (ETDEWEB)

    Hope, Einar; Skjeret, Frode

    2008-04-15

    The purpose of this state-of-the-art research paper is to surveying the literature on investment in market based electric power systems as a background for identifying and discussing some important issues in the optimal design and operation of such systems. A fundamental distinction has to be made between investment in the competitive part of the power system (generation and trading) on the one hand and the natural monopoly part (network infrastructure) on the other. The paper starts with a listing and discussion on market characteristics and properties of electric power and goes on to discussing performance criteria and potential sources of market failure for optimal electric power investment. After the literature survey there is a discussion of conditions under which optimal investment may occur. (author). 78 refs., figs

  7. Operations research techniques applied to service center logistics in power distribution users

    Directory of Open Access Journals (Sweden)

    Maria Teresinha Arns Steiner

    2006-12-01

    Full Text Available This paper deals with the optimization for the logistics regarding services demanded byusers of power distribution lines, served by the Portão office, located in Curitiba, PR, Brazil,and operated by COPEL (Paranaense Power Company. Through the use of OperationsResearch techniques, an Integer Programming Mathematical model and Floyd Algorithm, amethod was defined to determine in an optimized way, the number of teams needed by theselected office, as well as, the optimized assignment for the teams to the sites in need, inorder to offer efficient services to the users and, besides that, the immediate execution onemergencies and, as to the other services, accordingly to parameters set by the NationalPower Agency together with COPEL. The methodology hereby presented is generic, so thatit could be applied to any power network (or any of its lines, and it has presented verysatisfactory results to the case in analysis.

  8. Using the Power Balance Wristband to Improve Students' Research-Design Skills

    Science.gov (United States)

    Lawson, Timothy J.; Blackhart, Ginette C.; Gialopsos, Brooke M.

    2016-01-01

    We describe an exercise involving the power balance wristband (PBW) designed to enhance students' ability to design scientific tests. An instructor demonstrated that the PBW improved a student's balance, strength, and flexibility and invited students to design and conduct a brief scientific test of the PBW. Research methods students who…

  9. Science Research Group Leader's Power and Members' Compliance and Satisfaction with Supervision

    Science.gov (United States)

    Meng, Yi; He, Jia; Luo, Changkun

    2014-01-01

    This study investigated the correlations between science research group members' perceptions of power bases used by their group (lab, team) leader (coercive, reward, legitimate, expert and referent) and the effect of those perceptions on group members' attitudinal compliance, behavioral compliance, and satisfaction with supervision. Participants…

  10. Conceptual and Practical Implications for Rehabilitation Research: Effect Size Estimates, Confidence Intervals, and Power

    Science.gov (United States)

    Ferrin, James M.; Bishop, Malachy; Tansey, Timothy N.; Frain, Michael; Swett, Elizabeth A.; Lane, Frank J.

    2007-01-01

    For a number of conceptually and practically important reasons, reporting of effect size estimates, confidence intervals, and power in parameter estimation is increasingly being recognized as the preferred approach in social science research. Unfortunately, this practice has not yet been widely adopted in the rehabilitation or general counseling…

  11. Sport Physiology Research and Governing Gender in Sport--A Power-Knowledge Relation?

    Science.gov (United States)

    Larsson, Hakan

    2013-01-01

    This article sets out to show how physiological knowledge about sex/gender relates to power issues within sport. The sport physiology research at the Swedish School of Sport and Health Sciences (Swedish acronym: GIH) during the twentieth century is analysed in relation to the political rationality concerning gender at GIH and within the Swedish…

  12. Overview of Multi-Kilowatt Free-Piston Stirling Power Conversion Research at GRC

    Science.gov (United States)

    Geng, Steven M.; Mason, Lee S.; Dyson, Rodger W.; Penswick, L. Barry

    2008-01-01

    As a step towards development of Stirling power conversion for potential use in Fission Surface Power (FSP) systems, a pair of commercially available 1 kW class free-piston Stirling convertors and a pair of commercially available pressure wave generators (which will be plumbed together to create a high power Stirling linear alternator test rig) have been procured for in-house testing at Glenn Research Center. Delivery of both the Stirling convertors and the linear alternator test rig is expected by October, 2007. The 1 kW class free-piston Stirling convertors will be tested at GRC to map and verify performance. The convertors will later be modified to operate with a NaK liquid metal pumped loop for thermal energy input. The high power linear alternator test rig will be used to map and verify high power Stirling linear alternator performance and to develop power management and distribution (PMAD) methods and techniques. This paper provides an overview of the multi-kilowatt free-piston Stirling power conversion work being performed at GRC.

  13. Distribution Grid Fault Location Applying Transient Zero-mode Current

    Directory of Open Access Journals (Sweden)

    Yunchuan Zhang

    2012-09-01

    Full Text Available To aim at the puzzles on faults location in distribution grids, the paper analyzed the distributing characteristics of transient zero-mode currents as the faults occurred, with the aid of correlation theory, a new fault circuit-selection and fault-location method was proposed based on transient zero model current for power distribution grid faults. The method is based on such a fact that the RMS was maximum of fault line transient zero-mode current, and the inner products between it and other line transient zero-mode current were less than zero, in addition, the transient zero-model currents at two sides of the fault point possessed opposite polarity and diverse waveform, and as well as small correlation coefficient closer to zero. In the end, the simulation results show that the proposed method on circuit-selection and fault-location for power distribution grids fault based on transient zero- mode current is correct and effective, and not affected by voltage epoch angle, and grounding resistance, and as well as neutral-point grounding modes.

  14. Distribution and Artificial Prevention of Hail in Daxing'anling%大兴安岭地区冰雹的分布及人工预防

    Institute of Scientific and Technical Information of China (English)

    边洪俊

    2011-01-01

    The distribution and artificial prevention of hail in the main agricultural production area of Daxing'anling are introduced,with the future arrangement of hail prevention equipment and artificial hail prevention measures presented.%介绍了大兴安岭地区农业主产区冰雹的分布及人工防雹现状,提出了未来防雹设备布局及人工防雹措施。

  15. A shift from significance test to hypothesis test through power analysis in medical research

    Directory of Open Access Journals (Sweden)

    Singh Girish

    2006-01-01

    Full Text Available Medical research literature until recently, exhibited substantial dominance of the Fisher′s significance test approach of statistical inference concentrating more on probability of type I error over Neyman-Pearson′s hypothesis test considering both probability of type I and II error. Fisher′s approach dichotomises results into significant or not significant results with a P value. The Neyman-Pearson′s approach talks of acceptance or rejection of null hypothesis. Based on the same theory these two approaches deal with same objective and conclude in their own way. The advancement in computing techniques and availability of statistical software have resulted in increasing application of power calculations in medical research and thereby reporting the result of significance tests in the light of power of the test also. Significance test approach, when it incorporates power analysis contains the essence of hypothesis test approach. It may be safely argued that rising application of power analysis in medical research may have initiated a shift from Fisher′s significance test to Neyman-Pearson′s hypothesis test procedure.

  16. National nuclear power plant safety research 2007-2010. Proposal for SAFIR2010 framework plan

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-07-01

    A country utilising nuclear energy is presumed to possess a sufficient infrastructure to cover the education and research in this field, besides the operating organisations of the plants and a regulatory body. The starting point of public nuclear safety research programmes is that they provide the necessary conditions for retaining the knowledge needed for ensuring the continuance of safe and economic use of nuclear power, for development of new know-how and for participation in international cooperation. In fact, the Finnish organisations engaged in research in this sector have been an important resource which the various ministries, the Radiation and Nuclear Safety Authority (STUK) and the power companies have had at their disposal. Ministry of Trade and Industry appointed a group to write the Framework Plan of the new programme. This report contains a proposal for the general outline of the programme, preliminarily entitled as SAFIR2010 (SAfety of Nuclear Power Plants - Finnish National Research Programme). The plan has been made for the period 2007-2010, but it is based on safety challenges identified for a longer time span as well. Olkiluoto 3, the new nuclear power plant unit under construction has also been taken into account in the plan. The safety challenges set by the existing plants and the new plant unit, as well as the ensuing research needs do, however, converge to a great extent. The research programme is strongly based on the Chapter 7a of the Finnish Nuclear Energy Act. The construction of the new power plant unit will increase the need for experts in the field in Finland. At the same time, the retirement of the existing experts is continuing. These factors together will call for more education and training, in which active research activities play a key role. This situation also makes long-term safety research face a great challenge. The Framework Plan aims to define the important research needs related to the safety challenges. The research into

  17. Zero Modes and Entanglement Entropy

    CERN Document Server

    Yazdi, Yasaman K

    2016-01-01

    Ultraviolet divergences are widely discussed in studies of entanglement entropy. Also present, but much less understood, are infrared divergences due to zero modes in the field theory. In this note, we discuss the importance of carefully handling zero modes in entanglement entropy. We give an explicit example for a chain of harmonic oscillators in 1D, where a mass regulator is necessary to avoid an infrared divergence due to a zero mode. We also comment on a surprising contribution of the zero mode to the UV-scaling of the entanglement entropy.

  18. Low statistical power in biomedical science: a review of three human research domains

    Science.gov (United States)

    Dumas-Mallet, Estelle; Button, Katherine S.; Boraud, Thomas; Gonon, Francois

    2017-01-01

    Studies with low statistical power increase the likelihood that a statistically significant finding represents a false positive result. We conducted a review of meta-analyses of studies investigating the association of biological, environmental or cognitive parameters with neurological, psychiatric and somatic diseases, excluding treatment studies, in order to estimate the average statistical power across these domains. Taking the effect size indicated by a meta-analysis as the best estimate of the likely true effect size, and assuming a threshold for declaring statistical significance of 5%, we found that approximately 50% of studies have statistical power in the 0–10% or 11–20% range, well below the minimum of 80% that is often considered conventional. Studies with low statistical power appear to be common in the biomedical sciences, at least in the specific subject areas captured by our search strategy. However, we also observe evidence that this depends in part on research methodology, with candidate gene studies showing very low average power and studies using cognitive/behavioural measures showing high average power. This warrants further investigation.

  19. Electric Power Lines : Questions and Answers on Research into Health Effects.

    Energy Technology Data Exchange (ETDEWEB)

    United States. Bonneville Power Administration.

    1995-06-01

    Most people know that electric power lines, like the wiring in our homes, can cause serious electric shocks if we`re not careful. Many people also want to know whether the EMF (electric and magnetic fields) produced by power lines and other electrical devices affect our health. Although no adverse health effects of electric power EMF have been confirmed, there is continued scientific uncertainty about this issue. Research on EMF is ongoing throughout the world. The purpose of this booklet is to answer some common questions that the BPA (Bonneville Power Administration) receives about the possible effects of power lines on health. First, some basic electrical terms are defined, and electric and magnetic fields are debed. Next, answers are given to several questions about recent scientific studies. Some important information about electrical safety follows. We then describe how BPA is addressing public concerns about potential health effects of power lines. The last section tells you how to obtain more detailed information about the health and safety issues summarized in this booklet.

  20. Research and development of photovoltaic power system; Taiyoko hatsuden system no jissho kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M. [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the result obtained during fiscal 1994 on a demonstration research on photovoltaic power generating systems. Solar cells with an output of 750 kW, storage battery facilities with an output of 3,058 kWh, three DC-AC converters with a rating of 250 kW, and a diesel generator with an output of 300 kW having been installed up to the previous fiscal year were combined to perform comprehensive adjustments and tests such as battery charge/discharge tests and AC parallel operation tests. The battery charge/discharge tests revealed that the 10 hour rate discharge capacity meets the specifications, and the batteries are free of deterioration after a demonstration operation of about 4.5 months. Difference between the power generation record and the planned value is thought due to the following reasons: the array output data in a power line connected system come about 90% of the simulation result due to correction coefficient for the solar cell conversion efficiency; the inclined face insolation results in less by about 7% than the planned value, and the transmittable power amount less by about 14% in total; the load power amount is less by about 7% than the planned value; and the balance supplementing power factor increases by about 4%. 5 figs., 2 tabs.

  1. Research on vibration characteristics of L-shaped plate using a mobility power flow approach

    Institute of Scientific and Technical Information of China (English)

    CHEN Xiao-li; SHENG Mei-ping

    2007-01-01

    L-shaped plates have become an important focuses in structural vibration research. To determine their vibration characteristics, this paper applied a mobility power flow method. Firstly, the L-shaped plate was divided into two substructures to simplify analysis. The coupled bending moment was then deduced by applying a continuous vibration property on the common edge. Next, the response on any point of the plate and the input and transmitted power flow formulas were calculated. Numerical simulations showed the distribution of the coupled bending moment and the response of the whole structure. The validity of this method was verified by the SEA approach.

  2. LOFA and RIA analysis of the Indonesian Multipurpose research reactor RSG-GAS (1)

    Energy Technology Data Exchange (ETDEWEB)

    Endiah Puji Hastuti; Hudi Hastowo; Iman Kuntoro [Center for Multipurpose Reactor, National Atomic Energy Agency (BATAN), Puspiptek, Serpong, Tangerang (Indonesia)

    1999-07-01

    Investigation on accident of the Indonesian Multipurpose research reactor RSG-GAS has been performed by computer simulation technique. Two groups of transients were considered, namely transient due to loss of primary cooling system (LOFA) and power excursion due to reactivity insertion (RIA). In such a transient condition, the Common Mode Failure (CMF) is considered and it will induce a situation so called unprotected transient or Anticipated Transient Without Scram (ATWS). RELAP5, PARET-ANL and EUREKA-2RR computer packages have been applied for these analyses. Simulations result done using these computer packages showed that in the occurrence of LOFA and RIA, failure on fuel elements is limited to the region with the highest power factor. (author)

  3. Concept of a nuclear powered submersible research vessel and a compact reactor

    Energy Technology Data Exchange (ETDEWEB)

    Kusunoki, Tsuyoshi; Odano, Naoteru; Yoritsune, Tsutomu; Ishida, Toshihisa [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Takahashi, Teruo [Energis, Co., Kobe, Hyogo (Japan); Nishimura, Hajime [Japan Marine Science and Technology Center, Yokosuka, Kanagawa (Japan); Tokunaga, Sango [Japan Deep Sea Technology Association, Tokyo (Japan)

    2001-07-01

    A conceptual design study of a submersible research vessel navigating in 600 m depth and a compact nuclear reactor were carried out for the expansion of the nuclear power utilization. The mission of the vessel is the research of mechanism of the climate change to predict the global environment. Through conditions of the Arctic Ocean and the sea at high latitude have significant impacts on the global environmental change, it is difficult to investigate those areas by ordinary ships because of thick ice or storm. Therefore the research vessel is mainly utilized in the Arctic Ocean and the sea at high latitude. By taking account of the research mission, the basic specifications of the vessel are decided; the total weight is 500 t, the submersible depth is 600 m, the maximum speed is 12 knots (22.2 km/h), and the number of crews is 16. Nuclear power has an advantage in supplying large power of electricity in the sea for long period. Based on the requirements, it has been decided that two sets of submersible compact reactor, SCR, which is light-weighted and of enhanced safety characteristics of supply the total electricity of 500 kW. (author)

  4. Research on a Small Signal Stability Region Boundary Model of the Interconnected Power System with Large-Scale Wind Power

    Directory of Open Access Journals (Sweden)

    Wenying Liu

    2015-03-01

    Full Text Available For the interconnected power system with large-scale wind power, the problem of the small signal stability has become the bottleneck of restricting the sending-out of wind power as well as the security and stability of the whole power system. Around this issue, this paper establishes a small signal stability region boundary model of the interconnected power system with large-scale wind power based on catastrophe theory, providing a new method for analyzing the small signal stability. Firstly, we analyzed the typical characteristics and the mathematic model of the interconnected power system with wind power and pointed out that conventional methods can’t directly identify the topological properties of small signal stability region boundaries. For this problem, adopting catastrophe theory, we established a small signal stability region boundary model of the interconnected power system with large-scale wind power in two-dimensional power injection space and extended it to multiple dimensions to obtain the boundary model in multidimensional power injection space. Thirdly, we analyzed qualitatively the topological property’s changes of the small signal stability region boundary caused by large-scale wind power integration. Finally, we built simulation models by DIgSILENT/PowerFactory software and the final simulation results verified the correctness and effectiveness of the proposed model.

  5. A Framework for Successful Research Experiences in the Classroom: Combining the Power of Technology and Mentors

    Science.gov (United States)

    Graff, Paige Valderrama; Stefanov, William L.; Willis, Kim; Runco, Susan; McCollum, Tim; Lindgren, Charles F.; Baker, Marshalyn; Mailhot, Michele

    2011-01-01

    Authentic research opportunities in the classroom are most impactful when they are student-driven and inquiry-based. These experiences are even more powerful when they involve technology and meaningful connections with scientists. In today's classrooms, activities are driven by state required skills, education standards, and state mandated testing. Therefore, programs that incorporate authentic research must address the needs of teachers. NASA's Expedition Earth and Beyond (EEAB) Program has developed a framework that addresses teacher needs and incorporates the use of technology and access to mentors to promote and enhance authentic research in the classroom. EEAB is a student involvement program that facilitates student investigations of Earth or planetary comparisons using NASA data. To promote student-led research, EEAB provides standards-aligned, inquiry-based curricular resources, an implementation structure to facilitate research, educator professional development, and ongoing support. This framework also provides teachers with the option to incorporate the use of technology and connect students with a mentor, both of which can enrich student research experiences. The framework is structured by a modeled 9-step process of science which helps students organize their research. With more schools gaining increased access to technology, EEAB has created an option to help schools take advantage of students' interest and comfort with technology by leveraging the use of available technologies to enhance student research. The use of technology not only allows students to collaborate and share their research, it also provides a mechanism for them to work with a mentor. This framework was tested during the 2010/2011 school year. Team workspaces hosted on Wikispaces for Educators allow students to initiate their research and refine their research question initially without external input. This allows teams to work independently and rely on the skills and interests of

  6. The Development and Research on the Coordinate Control Strategy Between Turbine and Boiler in Fossil Power Plant

    Institute of Scientific and Technical Information of China (English)

    WEI Shuangying

    2006-01-01

    Based on the research on domestic and international automatic technical development in fossil power plant, the paper analyses the recent situation of the coordinate control system between turbine and boiler of domestic fossil Power Plant, provides the development thought of coordinate control system between turbine and boiler, and describes the application prospect in control system of fossil power plant combining with the application experience.

  7. The Influence of Power Shifts in Data Collection and Analysis Stages: A Focus on Qualitative Research Interview

    Science.gov (United States)

    Anyan, Frederick

    2013-01-01

    This paper analyzes the power relation between the interviewer and the interviewee in the qualitative research interview methodology. The paper sets out to grapple with the extent to which the dynamisms in power shifts influence data collection and analysis in the interview methodology. The exploration of power shifts in the qualitative research…

  8. SAFIR2010. The Finnish Research Programme on Nuclear Power Plant Safety 2007-2010. Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Puska, E.K.; Suolanen, V. (eds.)

    2011-02-15

    Major part of Finnish public research on nuclear power plant safety during the years 2007-2010 has been carried out in the SAFIR2010 programme. The steering group of SAFIR2010 consisted of representatives from Radiation and Nuclear Safety Authority (STUK), Ministry of Employment and the Economy (MEE), Technical Research Centre of Finland (VTT), Teollisuuden Voima Oyj (TVO), Fortum Power and Heat Oyj, Fortum Nuclear Services Oy (Fortum), Finnish Funding Agency for Technology and Innovation (Tekes), Aalto University School of Science and Technology (Aalto, former Helsinki University of Technology) and Lappeenranta University of Technology (LUT). In addition to representatives of these organisations, the Steering Group had permanent experts from the Swedish Radiation Safety Authority (SSM) and Fennovoima Oy (Fennovoima). SAFIR2010 research programme was divided in eight research areas that were Organisation and human, Automation and control room, Fuel and reactor physics, Thermal hydraulics, Severe accidents, Structural safety of reactor circuit, Construction safety, and Probabilistic Safety Analysis (PSA). Research projects of the programme were chosen on the basis of annual call for proposals. The annual volume of the SAFIR2010-programme in 2007-2010 has been 6,5-7,1 M euro and approximately 50 person years. Main funding organisations in 2007-2010 have been the State Waste Management Fund VYR with 2,7-3,0 M euro and VTT with 2,4-2,7 M euro annually. In 2010 research was carried out in 33 projects. The research in the programme has been carried out primarily by VTT Technical Research Centre of Finland. Other research units responsible for the projects solely or in co-operation with other institutions include Lappeenranta University of Technology, Aalto University (previously Helsinki University of Technology), Tampere University of Technology, Fortum Power and Heat Oy (previously Fortum Nuclear Services Oy), Finnish Institute of Occupational Health and Finnish

  9. Issues and future direction of thermal-hydraulics research and development in nuclear power reactors

    Energy Technology Data Exchange (ETDEWEB)

    Saha, P., E-mail: pradip.saha@ge.com [GE Hitachi Nuclear Energy, Wilmington, NC (United States); Aksan, N. [GRNSPG Group, University of Pisa (Italy); Andersen, J. [GE Hitachi Nuclear Energy, Wilmington, NC (United States); Yan, J. [Westinghouse Electric Co., Columbia, SC (United States); Simoneau, J.P. [AREVA, Lyon (France); Leung, L. [Atomic Energy of Canada Ltd., Chalk River, Ontario (Canada); Bertrand, F. [CEA, DEN, DER, F-13108 Saint-Paul-Lez-Durance (France); Aoto, K.; Kamide, H. [Japan Atomic Energy Agency, Chiyoda-ku, Tokyo (Japan)

    2013-11-15

    The paper archives the proceedings of an expert panel discussion on the issues and future direction of thermal-hydraulic research and development in nuclear power reactors held at the NURETH-14 conference in Toronto, Canada, in September 2011. Thermal-hydraulic issues related to both operating and advanced reactors are presented. Advances in thermal-hydraulics have significantly improved the performance of operating reactors. Further thermal-hydraulics research and development is continuing in both experimental and computational areas for operating reactors, reactors under construction or ready for near-term deployment, and advanced Generation-IV reactors. As the computing power increases, the fine-scale multi-physics computational models, coupled with the systems analysis code, are expected to provide answers to many challenging problems in both operating and advanced reactor designs.

  10. Discourse, Power, and Knowledge in the Management of "Big Science": The Production of Consensus in a Nuclear Fusion Research Laboratory.

    Science.gov (United States)

    Kinsella, William J.

    1999-01-01

    Extends a Foucauldian view of power/knowledge to the archetypical knowledge-intensive organization, the scientific research laboratory. Describes the discursive production of power/knowledge at the "big science" laboratory conducting nuclear fusion research and illuminates a critical incident in which the fusion research…

  11. First lasing at the high-power free electron laser at Siberian center for photochemistry research

    Science.gov (United States)

    Antokhin, E. A.; Akberdin, R. R.; Arbuzov, V. S.; Bokov, M. A.; Bolotin, V. P.; Burenkov, D. B.; Bushuev, A. A.; Veremeenko, V. F.; Vinokurov, N. A.; Vobly, P. D.; Gavrilov, N. G.; Gorniker, E. I.; Gorchakov, K. M.; Grigoryev, V. N.; Gudkov, B. A.; Davydov, A. V.; Deichuli, O. I.; Dementyev, E. N.; Dovzhenko, B. A.; Dubrovin, A. N.; Evtushenko, Yu. A.; Zagorodnikov, E. I.; Zaigraeva, N. S.; Zakutov, E. M.; Erokhin, A. I.; Kayran, D. A.; Kiselev, O. B.; Knyazev, B. A.; Kozak, V. R.; Kolmogorov, V. V.; Kolobanov, E. I.; Kondakov, A. A.; Kondakova, N. L.; Krutikhin, S. A.; Kryuchkov, A. M.; Kubarev, V. V.; Kulipanov, G. N.; Kuper, E. A.; Kuptsov, I. V.; Kurkin, G. Ya.; Labutskaya, E. A.; Leontyevskaya, L. G.; Loskutov, V. Yu.; Matveenko, A. N.; Medvedev, L. E.; Medvedko, A. S.; Miginsky, S. V.; Mironenko, L. A.; Motygin, S. V.; Oreshkov, A. D.; Ovchar, V. K.; Osipov, V. N.; Persov, B. Z.; Petrov, S. P.; Petrov, V. M.; Pilan, A. M.; Poletaev, I. V.; Polyanskiy, A. V.; Popik, V. M.; Popov, A. M.; Rotov, E. A.; Salikova, T. V.; Sedliarov, I. K.; Selivanov, P. A.; Serednyakov, S. S.; Skrinsky, A. N.; Tararyshkin, S. V.; Timoshina, L. A.; Tribendis, A. G.; Kholopov, M. A.; Cherepanov, V. P.; Shevchenko, O. A.; Shteinke, A. R.; Shubin, E. I.; Scheglov, M. A.

    2004-08-01

    The first lasing near wavelength 140 μm was achieved in April 2003 on a high-power free electron laser (FEL) constructed at the Siberian Center for Photochemical Research. In this paper, we briefly describe the design of FEL driven by an accelerator-recuperator. Characteristics of the electron beam and terahertz laser radiation, obtained at the first experiments, are also presented in the paper.

  12. Electronic imaging system for neutron radiography at a low power research reactor

    Energy Technology Data Exchange (ETDEWEB)

    Ferreira, F.J.O., E-mail: fferreira@ien.gov.b [Instituto de Engenharia Nuclear, Comissao Nacional de Energia Nuclear, Caixa Postal 68550, CEP 21945-970, Rio de Janeiro (Brazil); Silva, A.X.; Crispim, V.R. [PEN/COPPE-DNC/POLI CT, Universidade Federal do Rio de Janeiro, Ilha do Fundao, Caixa Postal 68509, 21945-970 Rio de Janeiro (Brazil)

    2010-08-15

    This paper describes an electronic imaging system for producing real time neutron radiography from a low power research reactor, which will allow inspections of samples with high efficiency, in terms of measuring time and result analysis. This system has been implanted because of its potential use in various scientific and industrial areas where neutron radiography with photographic film could not be applied. This real time system is installed in neutron radiography facility of Argonauta nuclear research reactor, at the Instituto de Engenharia Nuclear of the Comissao Nacional de Energia Nuclear, in Brazil. It is adequate to perform real time neutron radiography of static and dynamic events of samples.

  13. Small UAV Research and Evolution in Long Endurance Electric Powered Vehicles

    Science.gov (United States)

    Logan, Michael J.; Chu, Julio; Motter, Mark A.; Carter, Dennis L.; Ol, Michael; Zeune, Cale

    2007-01-01

    This paper describes recent research into the advancement of small, electric powered unmanned aerial vehicle (UAV) capabilities. Specifically, topics include the improvements made in battery technology, design methodologies, avionics architectures and algorithms, materials and structural concepts, propulsion system performance prediction, and others. The results of prototype vehicle designs and flight tests are discussed in the context of their usefulness in defining and validating progress in the various technology areas. Further areas of research need are also identified. These include the need for more robust operating regimes (wind, gust, etc.), and continued improvement in payload fraction vs. endurance.

  14. Electromagnetic pulse research on electric power systems: Program summary and recommendations

    Energy Technology Data Exchange (ETDEWEB)

    Barnes, P.R.; McConnell, B.W.; Van Dyke, J.W. (Oak Ridge National Lab., TN (United States)); Tesche, F.M. (Tesche (F.M.), Dallas, TX (United States)); Vance, E.F. (Vance (E.F.), Fort Worth, TX (United States))

    1993-01-01

    A single nuclear detonation several hundred kilometers above the central United States will subject much of the nation to a high-altitude electromagnetic pulse (BENT). This pulse consists of an intense steep-front, short-duration transient electromagnetic field, followed by a geomagnetic disturbance with tens of seconds duration. This latter environment is referred to as the magnetohydrodynamic electromagnetic pulse (NMENT). Both the early-time transient and the geomagnetic disturbance could impact the operation of the nation's power systems. Since 1983, the US Department of Energy has been actively pursuing a research program to assess the potential impacts of one or more BENT events on the nation's electric energy supply. This report summarizes the results of that program and provides recommendations for enhancing power system reliability under HENT conditions. A nominal HENP environment suitable for assessing geographically large systems was developed during the program and is briefly described in this report. This environment was used to provide a realistic indication of BEMP impacts on electric power systems. It was found that a single high-altitude burst, which could significantly disturb the geomagnetic field, may cause the interconnected power network to break up into utility islands with massive power failures in some areas. However, permanent damage would be isolated, and restoration should be possible within a few hours. Multiple bursts would likely increase the blackout areas, component failures, and restoration time. However, a long-term blackout of many months is unlikely because major power system components, such as transformers, are not likely to be damaged by the nominal HEND environment. Moreover, power system reliability, under both HENT and normal operating conditions, can be enhanced by simple, and often low cost, modifications to current utility practices.

  15. Nurses’ Perceptions of the Concept of Power in Nursing: A Qualitative Research

    Science.gov (United States)

    Sepasi, Rana Rezai; Borhani, Fariba; Rafiei, Hossein

    2016-01-01

    Introduction Power is a complex and extensive concept in nursing, which has a decisive impact on the accomplishment of duties, satisfaction and achievement of professional goals. Explaining the concept of power in nursing from the perspective of nurses and accessing its various dimensions may result in a better understanding of this issue. Aim This study was aimed to explore the concept of power in nursing, using the views and experiences of Iranian nurses. Materials and Methods This study was a qualitative research which used a content analysis approach. Participants were selected from among nurses active in clinical, management, and educational practices using the purposive sampling method. Data were collected using a semi-structured individual interview. The results were obtained by analysing the data using an inductive approach and the constant comparison method. Results The participants of this study regarded the power of nursing as a positive concept and the issue of power in nursing consisted of three classes, the genesis with the subclasses of “being purposeful”, “being under the shadow of the profession nature”, “being dependent on the source”, strengthening with the subclasses of “being emotional and introverted”, “being formed in the context of professional communication”, “fluidity and flowing”, and the evolution with the subclasses “based on human values”, and “being a tool for professional excellence”. Conclusion The concept of power in nursing can be considered a purposeful issue based on the nurses’ viewpoint which flourishes in the context of human, moral and caring nature of the nursing profession. According to its dependence on the nature of profession and on the basis of professional communication, Power of nursing grows with a fluidlike flowing structure, linked with human values, reaches maturity and results in outcomes such as improving the quality of care and professional excellence. PMID:28208886

  16. Historical perspectives: The role of the NASA Lewis Research Center in the national space nuclear power programs

    Science.gov (United States)

    Bloomfield, H. S.; Sovie, R. J.

    1991-01-01

    The history of the NASA Lewis Research Center's role in space nuclear power programs is reviewed. Lewis has provided leadership in research, development, and the advancement of space power and propulsion systems. Lewis' pioneering efforts in nuclear reactor technology, shielding, high temperature materials, fluid dynamics, heat transfer, mechanical and direct energy conversion, high-energy propellants, electric propulsion and high performance rocket fuels and nozzles have led to significant technical and management roles in many national space nuclear power and propulsion programs.

  17. Dense transient pinches and pulsed power technology: research and applications using medium and small devices

    Energy Technology Data Exchange (ETDEWEB)

    Soto, Leopoldo; Pavez, Cristian; Moreno, Jose; Cardenas, Miguel; Zambra, Marcelo [Comision Chilena de EnergIa Nuclear, Casilla 188-D, Santiago (Chile); Tarifeno, Ariel; Huerta, Luis; Tenreiro, Claudio; Giordano, Jose Luis; Lagos, Miguel; Escobar, Rodrigo; Ramos, Jorge; Altamirano, Luis [P4-Center for Research and Applications in Plasma Physics and Pulsed Power, Santiago and Curico (Chile); Retamal, Cesar [Facultad de IngenierIa de la Universidad de Talca, Curico (Chile); Silva, Patricio, E-mail: lsoto@cchen.cl

    2008-10-15

    The Plasma Physics and Plasma Technology Group of the Chilean Nuclear Energy Commission (CCHEN) has, since about ten years ago, used plasma production devices to study dense hot plasmas, particularly Z-pinches and plasma foci (PFs). In the case of Z-pinches, the studies include studies on the dynamics and stability of gas-embedded Z-pinches at currents of thermonuclear interest, and preliminary studies on wire arrays. For PF research, the aim of the work has been to characterize the physics of these plasmas and also to carry out the design and construction of smaller devices-in terms of both input energy and size-capable of providing dense hot plasmas. In addition, taking advantage of the experience in pulsed power technology obtained from experimental researches in dense transient plasmas, an exploratory line of pulsed power applications is being developed. In this paper, a brief review listing the most important results achieved by the Plasma Physics and Plasma Technology Group of the CCHEN is presented, including the scaling studies, PF miniaturization and diagnostics and research on Z-pinches at currents of thermonuclear interest. Then, exploratory applications of pulsed power are presented, including nanoflashes of radiation for radiography and substances detection, high pulsed magnetic fields generation and rock fragmentation.

  18. Materials for advanced power engineering 2010. Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Lecomte-Beckers, Jacqueline; Contrepois, Quentin; Beck, Tilmann; Kuhn, Bernd (eds.)

    2010-07-01

    The 9th Liege Conference on ''Materials for Advanced Power Engineering'' presents the results of the materials related COST Actions 536 ''Alloy Development for Critical Components of Environmentally Friendly Power Plants'' and 538 ''High Temperature Plant Lifetime Extension''. In addition, the broad field of current materials research perspectives for high efficiency, low- and zero- emission power plants and new energy technologies for the next decades are reported. The Conference proceedings are structured as follows: 1. Materials for advanced steam power plants; 2. Gas turbine materials; 3. Materials for nuclear fission and fusion; 4. Solid oxide fuel cells; 5. Corrosion, thermomechanical fatigue and modelling; 6. Zero emission power plants.

  19. Tests on the directional elements of zero-sequence power of 110 kV line for Yamzho Yumco Pumped Storage Station under the load condition%羊湖电厂110 kV线路零序功率 方向元件带负荷试验

    Institute of Scientific and Technical Information of China (English)

    戴雪梅; 尹晓霞

    2001-01-01

    按绝对值比较原理构成的零序功率方向元件,在零序电流方向保护中应用极为广泛。在常规的模拟调试中难以直接模拟出运行状态下接地故障时的零序电流和零序电压,因此要正确判断零序功率方向元件接线的正确与否,应在带负荷状态下,用负荷电流通过人为改变保护用的电流互感器和电压互感器二次回路的接线方式,来达到试验目的。%:The directional element of zero-sequence power, as a judgment element, is made in accordance with the absolute value comparison principle and is widely applied in the direction protection of zero-sequence current. In the routine simulation tests, it is difficult to simulate directly the zero-sequence current and voltage under the operation condition during earthing failure. In order to judge accurately the correctness of the connection of directional elements of zero-sequence power, the tests should be made under load condition. In this way, we can use load current to change the protective current transformer and potential transformer to reach the test objective.

  20. Impacts of Western Area Power Administration`s power marketing alternatives on utility demand-side management and conservation and renewable energy programs

    Energy Technology Data Exchange (ETDEWEB)

    Cavallo, J.D.; Germer, M.F.; Tompkins, M.M.

    1995-03-01

    The Western Area Power Administration (Western) requires all of its long-term firm power customers to implement programs that promote the conservation of electric energy or facilitate the use of renewable energy resources. Western has also proposed that all customers develop integrated resource plans that include cost-effective demand-side management programs. As part of the preparation of Western`s Electric Power Marketing Environmental Impact Statement, Argonne National Laboratory (ANL) developed estimates of the reductions in energy demand resulting from Western`s conservation and renewable energy activities in its Salt Lake City Area Office. ANL has also estimated the energy-demand reductions from cost-effective, demand-side management programs that could be included in the integrated resource plans of the customers served by Western`s Salt Lake City Area Office. The results of this study have been used to adjust the expected hourly demand for Western`s major systems in the Salt Lake City Area. The expected hourly demand served as the basis for capacity expansion plans develops with ANL`s Production and Capacity Expansion (PACE) model.

  1. Research on design feasibility of high-power light-weight dc-to-dc converters for space power applications

    Science.gov (United States)

    Wilson, T. G.

    1981-11-01

    Utilizing knowledge gained from past experience with experimental current-or-voltage step-up dc-to-dc converter power stages operating at output powers up to and in excess of 2 kW, a new experimental current-or-voltage step-up power stage using paralleled bipolar junction transistors (BJTs) as the controlled power switch, was constructed during the current reporting period. The major motivation behind the construction of this new experimental power stage was to improve the circuit layout so as to reduce the effects of stray circuit parasitic inductances resulting from excess circuit lead lengths and circuit loops, and to take advantage of the layout improvements which could be made when some recently-available power components, particularly power diodes and polypropylene filter capacitors, were incorporated into the design.

  2. Scientists Zero in On Brain Area Linked to 'Parkinson's Gait'

    Science.gov (United States)

    ... Scientists Zero in on Brain Area Linked to 'Parkinson's Gait' Discovery could lead to new treatments for ... play a role in walking difficulties that afflict Parkinson's disease patients, new research suggests. The prefrontal cortex ...

  3. The Prospect of Neutron Scattering In the 21st Century: A Powerful Tool for Materials Research

    Directory of Open Access Journals (Sweden)

    E. Kartini

    2007-07-01

    Full Text Available Over the last 60 years research reactors (RRs have played an important role in technological and socio-economical development of mankind, such as radioisotope production for medicine, industry, research and education. Neutron scattering has been widely used for research and development in materials science. The prospect of neutron scattering as a powerful tool for materials research is increasing in the 21st century. This can be seen from the investment of several new neutron sources all over the world such as the Spallation Neutron Source (SNS in USA, the Japan Proton Accelerator Complex (JPARC in Japan, the new OPAL Reactor in Australia, and some upgrading to the existing sources at ISIS, Rutherford Appleton Laboratory, UK; Institute of Laue Langevin (ILL in Grenoble, France and Berlin Reactor, Germany. Developing countries with moderate flux research reactor have also been involved in this technique, such as India, Malaysia and Indonesia. The Siwabessy Multipurpose Reactor in Serpong, Indonesia that also produces thermal neutron has contributed to the research and development in the Asia Pacific Region. However, the international joint research among those countries plays an important role on optimizing the results.

  4. SAFIR2010. The Finnish research programme on nuclear power plant safety 2007-2010. Interim report

    Energy Technology Data Exchange (ETDEWEB)

    Puska, E.K. (ed.)

    2009-02-15

    Major part of Finnish public research on nuclear power plant safety during the years 2007-2008 has been carried out in the SAFIR2010 programme. The steering group of SAFIR2010 consists of representatives from Radiation and Nuclear Safety Authority (STUK), Ministry of Employment and the Economy (MEE), VTT Technical Research Centre of Finland (VTT), Teollisuuden Voima Oyj (TVO), Fortum Power and Heat Oyj, Fortum Nuclear Services Oy (Fortum), Tekes - the Finnish Funding Agency for Technology and Innovation (Tekes), Helsinki University of Technology (TKK) and Lappeenranta University of Technology (LUT). In addition to representatives of these organisations, the Steering Group has permanent experts from the Swedish Radiation Safety Authority (SSM) and Fennovoima Oy (Fennovoima). SAFIR2010 research programme is divided in eight research areas that are Organisation and human, Automation and control room, Fuel and reactor physics, Thermal hydraulics, Severe accidents, Structural safety of reactor circuit, Construction safety, and Probabilistic Safety Analysis (PSA). Research projects of the programme are chosen on the basis of annual call for proposals. The annual volume of the SAFIR2010 programme in 2007-2008 has been 6,3-6,7 M euro and approximately 50 person years. Main funding organisations in 2007-2008 were State Waste Management Fund VYR with 2,7-3,0 M euro and VTT with 2,4-2,5 M euro annually. In 2008 research was carried out in 30 projects. The research in the programme has been carried out primarily by VTT Technical Research Centre of Finland. Other research units responsible for the projects solely or in co-operation with other institutions include Lappeenranta University of Technology, Helsinki University of Technology, Tampere University of Technology, Fortum Nuclear Services Oy, Finnish Institute of Occupational Health and Finnish Meteorological Institute. In addition, there have been a few minor subcontractors in some projects. The programme management

  5. From Zero Energy Buildings to Zero Energy Districts

    Energy Technology Data Exchange (ETDEWEB)

    Polly, Ben; Kutscher, Chuck; Macumber, Dan; Schott, Marjorie; Pless, Shanti; Livingood, Bill; Van Geet, Otto

    2016-08-26

    Some U.S. cities are planning advanced districts that have goals for zero energy, water, waste, and/or greenhouse gas emissions. From an energy perspective, zero energy districts present unique opportunities to cost-effectively achieve high levels of energy efficiency and renewable energy penetration across a collection of buildings that may be infeasible at the individual building scale. These high levels of performance are accomplished through district energy systems that harness renewable and wasted energy at large scales and flexible building loads that coordinate with variable renewable energy supply. Unfortunately, stakeholders face a lack of documented processes, tools, and best practices to assist them in achieving zero energy districts. The National Renewable Energy Laboratory (NREL) is partnering on two new district projects in Denver: the National Western Center and the Sun Valley Neighborhood. We are working closely with project stakeholders in their zero energy master planning efforts to develop the resources needed to resolve barriers and create replicable processes to support future zero energy district efforts across the United States. Initial results of these efforts include the identification and description of key zero energy district design principles (maximizing building efficiency, solar potential, renewable thermal energy, and load control), economic drivers, and master planning principles. The work has also resulted in NREL making initial enhancements to the U.S. Department of Energy's open source building energy modeling platform (OpenStudio and EnergyPlus) with the long-term goal of supporting the design and optimization of energy districts.

  6. 基于模糊自适应控制的接触器过零投切系统研究%Research on Contactor Zero Crossing Switching System Based on Fuzzy Adaptive Control

    Institute of Scientific and Technical Information of China (English)

    韩宇泽; 王立国

    2014-01-01

    以负载变化不剧烈条件下高压动态无功补偿为研究背景,发挥接触器在高压领域的优势,针对接触器投切电容器造成的投切瞬间会产生浪涌电流及过电压的问题,提出接触器过零投切的同步关合控制方式。通过对接触器的动态特性分析,对真空接触器控制系统设计,并对接触器响应时间进行实验测试,基于接触器响应时间与操作电压以及环境温度的变化规律进行归纳,提出采用模糊自适应控制对不同环境温度以及操作电压下的接触器响应时间的预估方法,做到投切电容器的时间控制在电压电流零点附近的1ms 内,并进行相应的仿真与实验验证,取得了良好的效果。所作研究可有效控制电容器在投切瞬间产生的浪涌电流和电压闪变的不利影响,确保在满足系统无功补偿的条件下实现电网的安全稳定运行。%Considering the high pressure dynamic reactive power compensation with the load changing gently and the advantage of contactor in high pressure field,a contactor zero - crossing switching synchronization closing control mechanism has been proposed in this paper,aiming at the problem of instant overvoltage and surge current casued by contactor switching capacitor. Through the dynamic characteristics analysis of the contactor and the designing of the vacuum contactor control system,as well as the test of the response time of the contactor,a fuzzy adaptive control based estimating method for the contactor response time with different ambient temperatures and operating voltages has been proposed in this paper,based on the summary of the response time of contactor based on operating voltage and ambient temperature,which will guarantee the time of switched within 1ms when the capacitor voltage and current control near zero. Corresponding simulations and experimental verifications have achieved good results. The proposed method can effectively control

  7. Preliminary Results From NASA's Space Solar Power Exploratory Research and Technology Program

    Science.gov (United States)

    Howell, Joe T.; Mankins, John C.

    2000-01-01

    Large solar power satellite (SPS) systems that might provide base load power into terrestrial markets were examined extensively in the 1970s by the US Department of Energy (DOE) and the National Aeronautics and Space Administration (NASA). Following a hiatus of about 15 years, the subject of space solar power (SSP) was reexamined by NASA from 1995-1997 in the "fresh look" study, and during 1998 in an SSP "concept definition study". As a result of these efforts, during 1999-2000, NASA has been conducting the SSP Exploratory Research and Technology (SERT) program. The goal of the SERT activity has been to conduct preliminary strategic technology research and development to enable large, multi-megawatt SSP systems and wireless power transmission (WPT) for government missions and commercial markets (in-space and terrestrial). In pursuing that goal, the SERT: (1) refined and modeled systems approaches for the utilization of SSP concepts and technologies, ranging from the near-term (e.g., for space science, exploration and commercial space applications) to the far-term (e.g., SSP for terrestrial markets), including systems concepts, architectures, technology, infrastructure (e.g. transportation), and economics; (2) conducted technology research, development and demonstration activities to produce "proof-of-concept" validation of critical SSP elements for both nearer and farther-term applications; and (3) engendered the beginnings of partnerships (nationally and internationally) that could be expanded, as appropriate, to pursue later SSP technology and applications. Through these efforts, the SERT should allow better informed future decisions regarding further SSP and related technology research and development investments by both NASA and prospective partners, and guide further definition of technology roadmaps - including performance objectives, resources and schedules, as well as "multi-purpose" applications (e.g., commerce, science, and government). This paper

  8. Development of a Powered Wheelchair Driving Simulator for Research and Development Use

    Science.gov (United States)

    Ito, Takuma; Shino, Motoki; Inoue, Takenobu; Kamata, Minoru

    The purpose of a powered wheelchair driving simulator is to decrease the time and effort in the process of clinic, research and development. In this paper, the design concepts of our driving simulator for research and development use are explained. To design the simulator's software and hardware, two following experiments were conducted. 1: The driver's horizontal field of view was measured. While making a right turn at a corner of a corridor, the movement of the driver's gazing point was measured. From this result, the maximum and minimum values of gazing point movement were analyzed to design the simulator's angle of view. 2: Motion cues such as acceleration and vibration were measured. The characteristics of these motion cues were analyzed to design the motion system. From the experiment results, a driving simulator of a powered wheelchair was developed. To evaluate the driving simulator, the experiment for comparing with a real powered wheelchair driving was conducted. Evaluations improved by the components which were specially designed for the driving simulator.

  9. A confirmatory research approach to the measurement of EMI/RFI in commercial nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Kercel, S.W. [Oak Ridge National Lab., TN (United States)

    1995-04-01

    The Oak Ridge National Laboratory (ORNL) is conducting confirmatory research on the measurement of electromagnetic/radio frequency interference (EMI/RFI) in nuclear power plants. While it makes a good beginning, the currently available research data are not sufficient to characterize the EMI/RFI environment of the typical nuclear plant. Data collected over several weeks at each of several observation points are required to meet this need. To collect the required data, several approaches are examined, the most promising of which is the relatively new technology of application specific spectral receivers. While several spectral receiver designs have been described in the literature, none is well suited for nuclear power plant EMI/RFI surveys. This paper describes the development of two receivers specifically designed for nuclear power plant EMI/RFI surveys. One receiver surveys electric fields between 5 MHz and 8 GHz, while the other surveys magnetic fields between 305 Hz and 5 MHz. The results of field tests at TVA`s Bull Run Fossil Plant are reported.

  10. A confirmatory research approach to the measurement of EMI/RFI in commercial nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Kercel, S.W.

    1995-02-01

    The Oak Ridge National Laboratory (ORNL) is conducting confirmatory research on the measurement of electromagnetic/radio frequency interference (EMI/RFI) in nuclear power plants while it makes a good beginning, the currently available research data are not sufficient to characterize the EMI/RFI environment of the typical nuclear plant. Data collected over several weeks at each of several observation points are required to meet this need. To collect the required data, several approaches are examined, the most promising of which is the relatively new technology of application specific spectral receivers. While several spectral receiver designs have been described in the literature, none is well suited for nuclear power plant EMI/RFI surveys. This paper describes the development of two receivers specifically designed for nuclear power plant EMI/RFI surveys. One receiver surveys electric fields between 5 MHz and 8 GHz, while the other surveys magnetic fields between 305 Hz and 5 MHz. The results of field tests at TVA`s Bull Run Fossil Plant are reported.

  11. High-Power Hall Propulsion Development at NASA Glenn Research Center

    Science.gov (United States)

    Kamhawi, Hani; Manzella, David H.; Smith, Timothy D.; Schmidt, George R.

    2014-01-01

    The NASA Office of the Chief Technologist Game Changing Division is sponsoring the development and testing of enabling technologies to achieve efficient and reliable human space exploration. High-power solar electric propulsion has been proposed by NASA's Human Exploration Framework Team as an option to achieve these ambitious missions to near Earth objects. NASA Glenn Research Center (NASA Glenn) is leading the development of mission concepts for a solar electric propulsion Technical Demonstration Mission. The mission concepts are highlighted in this paper but are detailed in a companion paper. There are also multiple projects that are developing technologies to support a demonstration mission and are also extensible to NASA's goals of human space exploration. Specifically, the In-Space Propulsion technology development project at NASA Glenn has a number of tasks related to high-power Hall thrusters including performance evaluation of existing Hall thrusters; performing detailed internal discharge chamber, near-field, and far-field plasma measurements; performing detailed physics-based modeling with the NASA Jet Propulsion Laboratory's Hall2De code; performing thermal and structural modeling; and developing high-power efficient discharge modules for power processing. This paper summarizes the various technology development tasks and progress made to date

  12. NASA Glenn Research Center Program in High Power Density Motors for Aeropropulsion

    Science.gov (United States)

    Brown, Gerald V.; Kascak, Albert F.; Ebihara, Ben; Johnson, Dexter; Choi, Benjamin; Siebert, Mark; Buccieri, Carl

    2005-01-01

    Electric drive of transport-sized aircraft propulsors, with electric power generated by fuel cells or turbo-generators, will require electric motors with much higher power density than conventional room-temperature machines. Cryogenic cooling of the motor windings by the liquid hydrogen fuel offers a possible solution, enabling motors with higher power density than turbine engines. Some context on weights of various systems, which is required to assess the problem, is presented. This context includes a survey of turbine engine weights over a considerable size range, a correlation of gear box weights and some examples of conventional and advanced electric motor weights. The NASA Glenn Research Center program for high power density motors is outlined and some technical results to date are presented. These results include current densities of 5,000 A per square centimeter current density achieved in cryogenic coils, finite element predictions compared to measurements of torque production in a switched reluctance motor, and initial tests of a cryogenic switched reluctance motor.

  13. The European Research on Severe Accidents in Generation-II and -III Nuclear Power Plants

    Directory of Open Access Journals (Sweden)

    Jean-Pierre Van Dorsselaere

    2012-01-01

    Full Text Available Forty-three organisations from 22 countries network their capacities of research in SARNET (Severe Accident Research NETwork of excellence to resolve the most important remaining uncertainties and safety issues on severe accidents in existing and future water-cooled nuclear power plants (NPP. After a first project in the 6th Framework Programme (FP6 of the European Commission, the SARNET2 project, coordinated by IRSN, started in April 2009 for 4 years in the FP7 frame. After 2,5 years, some main outcomes of joint research (modelling and experiments by the network members on the highest priority issues are presented: in-vessel degraded core coolability, molten-corium-concrete-interaction, containment phenomena (water spray, hydrogen combustion…, source term issues (mainly iodine behaviour. The ASTEC integral computer code, jointly developed by IRSN and GRS to predict the NPP SA behaviour, capitalizes in terms of models the knowledge produced in the network: a few validation results are presented. For dissemination of knowledge, an educational 1-week course was organized for young researchers or students in January 2011, and a two-day course is planned mid-2012 for senior staff. Mobility of young researchers or students between the European partners is being promoted. The ERMSAR conference is becoming the major worldwide conference on SA research.

  14. Taking power, politics, and policy problems seriously: the limits of knowledge translation for urban health research.

    Science.gov (United States)

    Murphy, Kelly; Fafard, Patrick

    2012-08-01

    Knowledge translation (KT) is a growing movement in clinical and health services research, aimed to help make research more relevant and to move research into practice and policy. This paper examines the conventional model of policy change presented in KT and assesses its applicability for increasing the impact of urban health research on urban health policy. In general, KT conceptualizes research utilization in terms of the technical implementation of scientific findings, on the part of individual decision-makers who can be "targeted" for a KT intervention, in a context that is absent of political interests. However, complex urban health problems and interventions infrequently resemble this single decision, single decision-maker model posited by KT. In order to clarify the conditions under which urban health research is more likely or not to have an influence on public policy development, we propose to supplement the conventional model with three concepts drawn from the social science: policy stages, policy networks, and a discourse analysis approach for theorizing power in policy-making.

  15. Affine morphisms at zero level

    CERN Document Server

    Das, Paramita; Gupta, Ved Prakash

    2010-01-01

    Given a finite index subfactor, we show that the {\\em affine morphisms at zero level} in the affine category over the planar algebra associated to the subfactor is isomorphic to the fusion algebra of the subfactor as a *-algebra.

  16. Research of new packaging and cooling technique for high power fiber laser used pump coupler

    Science.gov (United States)

    Mu, Wei; Si, Xu; Lin, Ya-jun; Xu, Cheng-lin; Ma, Yun-liang; Xiao, Chun

    2015-10-01

    This article analyzes the advantages and disadvantages of a packaging structure for pump coupler, where common heat conduction material is used. In this study, the possibility of using new technology of thermal conductivity is discussed. We also proposes a solution that make the function and effect of package more uniform. A serial of experiments are done for research the cooling effect and the working reliability of the fiber combiners and couplers. Experiment proves that after improved method of package, the cooling speed increases significantly comparing the sample with old type of package technique. The technique discussed in this paper will make the high power fiber laser working long time with steady power output and high efficiency.

  17. Numerical simulation and experimental research of the integrated high-power LED radiator

    Science.gov (United States)

    Xiang, J. H.; Zhang, C. L.; Gan, Z. J.; Zhou, C.; Chen, C. G.; Chen, S.

    2017-01-01

    The thermal management has become an urgent problem to be solved with the increasing power and the improving integration of the LED (light emitting diode) chip. In order to eliminate the contact resistance of the radiator, this paper presented an integrated high-power LED radiator based on phase-change heat transfer, which realized the seamless connection between the vapor chamber and the cooling fins. The radiator was optimized by combining the numerical simulation and the experimental research. The effects of the chamber diameter and the parameters of fin on the heat dissipation performance were analyzed. The numerical simulation results were compared with the measured values by experiment. The results showed that the fin thickness, the fin number, the fin height and the chamber diameter were the factors which affected the performance of radiator from primary to secondary.

  18. ZPC Matrices and Zero Cycles

    Directory of Open Access Journals (Sweden)

    Marina Arav

    2009-01-01

    Full Text Available Let H be an m×n real matrix and let Zi be the set of column indices of the zero entries of row i of H. Then the conditions |Zk∩(∪i=1k−1Zi|≤1 for all k  (2≤k≤m are called the (row Zero Position Conditions (ZPCs. If H satisfies the ZPC, then H is said to be a (row ZPC matrix. If HT satisfies the ZPC, then H is said to be a column ZPC matrix. The real matrix H is said to have a zero cycle if H has a sequence of at least four zero entries of the form hi1j1,hi1j2,hi2j2,hi2j3,…,hikjk,hikj1 in which the consecutive entries alternatively share the same row or column index (but not both, and the last entry has one common index with the first entry. Several connections between the ZPC and the nonexistence of zero cycles are established. In particular, it is proved that a matrix H has no zero cycle if and only if there are permutation matrices P and Q such that PHQ is a row ZPC matrix and a column ZPC matrix.

  19. Technological Transfer from Research Nuclear Reactors to New Generation Nuclear Power Reactors

    Science.gov (United States)

    Radulescu, Laura; Pavelescu, Margarit

    2010-01-01

    The goal of this paper is the analysis of the technological transfer role in the nuclear field, with particular emphasis on nuclear reactors domain. The presentation is sustained by historical arguments. In this frame, it is very important to start with the achievements of the first nuclear systems, for instant those with natural uranium as fuel and heavy water as moderator, following in time through the history until the New Generation Nuclear Power Reactors. Starting with 1940, the accelerated development of the industry has implied the increase of the global demand for energy. In this respect, the nuclear energy could play an important role, being essentially an unlimited source of energy. However, the nuclear option faces the challenges of increasingly demanding safety requirements, economic competitiveness and public acceptance. Worldwide, a significant amount of experience has been accumulated during development, licensing, construction, and operation of nuclear power reactors. The experience gained is a strong basis for further improvements. Actually, the nuclear programs of many countries are addressing the development of advanced reactors, which are intended to have better economics, higher reliability, improved safety, and proliferation-resistant characteristics in order to overcome the current concerns about nuclear power. Advanced reactors, now under development, may help to meet the demand for energy power of both developed and developing countries as well as for district heating, desalination and for process heat. The paper gives historical examples that illustrate the steps pursued from first research nuclear reactors to present advanced power reactors. Emphasis was laid upon the fact that the progress is due to the great discoveries of the nuclear scientists using the technological transfer.

  20. ANL Doppler flowmeter

    Science.gov (United States)

    Karplus, H. B.; Raptis, A. C.; Lee, S.; Simpson, T.

    1985-10-01

    A flowmeter has been developed for measuring flow velocity in hot slurries. The flowmeter works on an ultrasonic Doppler principle in which ultrasound is injected into the flowing fluid through the solid pipe wall. Isolating waveguides separate the hot pipe from conventional ultrasonic transducers. Special clamp-on high-temperature transducers also can be adapted to work well in this application. Typical flows in pilot plants were found to be laminar, giving rise to broad-band Doppler spectra. A special circuit based on a servomechanism sensor was devised to determine the frequency average of such a broad spectrum. The device was tested at different pilot plants. Slurries with particulates greater than 70 microns (0.003 in.) yielded good signals, but slurries with extremely fine particulates were unpredictable. Small bubbles can replace the coarse particles to provide a good signal if there are not too many. Successful operation with very fine particulate slurries may have been enhanced by the presence of microbubbles.

  1. Neutronics, steady-state, and transient analyses for the Poland MARIA reactor for irradiation testing of LEU lead test fuel assemblies from CERCA : ANL independent verification results.

    Energy Technology Data Exchange (ETDEWEB)

    Garner, P. L.; Hanan, N. A. (Nuclear Engineering Division)

    2011-06-07

    The MARIA reactor at the Institute of Atomic Energy (IAE) in Swierk (30 km SE of Warsaw) in the Republic of Poland is considering conversion from high-enriched uranium (HEU) to low-enriched uranium (LEU) fuel assemblies (FA). The FA design in MARIA is rather unique; a suitable LEU FA has never been designed or tested. IAE has contracted with CERCA (the fuel supply portion of AREVA in France) to supply 2 lead test assemblies (LTA). The LTAs will be irradiated in MARIA to burnup level of at least 40% for both LTAs and to 60% for one LTA. IAE may decide to purchase additional LEU FAs for a full core conversion after the test irradiation. The Reactor Safety Committee within IAE and the National Atomic Energy Agency in Poland (PAA) must approve the LTA irradiation process. The approval will be based, in part, on IAE submitting revisions to portions of the Safety Analysis Report (SAR) which are affected by the insertion of the LTAs. (A similar process will be required for the full core conversion to LEU fuel.) The analysis required was established during working meetings between Argonne National Laboratory (ANL) and IAE staff during August 2006, subsequent email correspondence, and subsequent staff visits. The analysis needs to consider the current high-enriched uranium (HEU) core and 4 core configurations containing 1 and 2 LEU LTAs in various core positions. Calculations have been performed at ANL in support of the LTA irradiation. These calculations are summarized in this report and include criticality, burn-up, neutronics parameters, steady-state thermal hydraulics, and postulated transients. These calculations have been performed at the request of the IAE staff, who are performing similar calculations to be used in their SAR amendment submittal to the PAA. The ANL analysis has been performed independently from that being performed by IAE and should only be used as one step in the verification process.

  2. Sound Arguments and Power in Evaluation Research and Policy-Making: A Measuring Instrument and Its Application.

    Science.gov (United States)

    Propper, Igno M. A. M.

    1993-01-01

    Proposes an instrument for assessing the extent to which either sound arguments or power are found in scientific and political discussions. Empirical research is described that investigated the relation between the quality of evaluation research and the quality of discussion in policy-making processes in which the research is used. (Contains 47…

  3. Research on EMI Reduction of Multi-stage Interleaved Bridgeless Power Factor Corrector

    DEFF Research Database (Denmark)

    Li, Qingnan; Thomsen, Ole Cornelius; Andersen, Michael A. E.

    2012-01-01

    Working as an electronic pollution eliminator, the Power Factor Corrector's (PFC) own Electromagnetic Interference (EMI) problems have been blocking its performance improvement for long. In this paper, a systematic research on EMI generation of a multi-stage Two-Boost-Circuit Interleaved Bridgeless...... PFC (IBPFC) is presented. The insight into relationship of interleaving stages, switching on/off oscillations and EMI reduction is discussed. Finally, a 3.5kW universal input 2-stage IBPFC prototype was built to verify the theoretical analysis. Experimental results show that significant EMI reductions...

  4. Research and development of CO2 Capture and Storage Technologies in Fossil Fuel Power Plants

    Directory of Open Access Journals (Sweden)

    Lukáš Pilař

    2012-01-01

    Full Text Available This paper presents the results of a research project on the suitability of post-combustion CCS technology in the Czech Republic. It describes the ammonia CO2 separation method and its advantages and disadvantages. The paper evaluates its impact on the recent technology of a 250 MWe lignite coal fired power plant. The main result is a decrease in electric efficiency by 11 percentage points, a decrease in net electricity production by 62 MWe, and an increase in the amount of waste water. In addition, more consumables are needed.

  5. Electric Power Research Institute Environmental Control Technology Center Report to the Steering Committee

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    1998-01-12

    Operations and maintenance continued this month at the Electric Power Research Institute's (EPRI's) Environmental Control Technology Center (ECTC). Testing for the month involved the Dry Sorbent Injection (DSI) test block with the Carbon Injection System. The 1.0 MW Cold-Side Selective Catalytic Reduction (SCR) unit, the 0.4 MW Mini-Pilot Wet Scrubber, and the 4.0 MW Pilot Wet Scrubber remained idle this month in a cold-standby mode and were inspected regularly. These units remain available for testing as future project work is identified.

  6. Application of Modelling and Simulation in Mechatronics and Fluid Power System Design - Education and Research

    DEFF Research Database (Denmark)

    Andersen, T. O.; Hansen, M. R.; Conrad, Finn

    2003-01-01

    The development within the engineering industry is ever more in the direction of an integration of electronics both on the component level and system level. This implies improved and more intelligentcomponents with increased funtionality at the same time as the variant creation is made in the ele...... and control can be useful in analysis, synthesis, design and application of mechatronic systems with fluid power actuation. The focus is on system aspects and describes several projects from education and research that utilises the mentioned methods and techniques....

  7. WebSpace - a WebWindows based gateway to the ANL LabSpace. Final report for period September 1, 1995 - August 31, 1998

    Energy Technology Data Exchange (ETDEWEB)

    Furmanski, Wojtek

    2002-04-11

    The goal of this project was to prototype a Web based computational and collaboratory environment that would act as a commodity technologies based front-end or Gateway to larger HPC systems such as ANL LabSpace. The original name - WebSpace - proposed for such a system was taken during the course of this project by Silicon Graphics and used for their Web authoring environment. To avoid confusion, we changed the name of this project's system to WebFlow.

  8. Design & Implementation of Zero Voltage Switching Buck Converter

    Directory of Open Access Journals (Sweden)

    A.Suresh Kumar

    2014-09-01

    Full Text Available Zero voltage switching (ZVS buck converter is more preferable over hard switched buck converter for low power, high frequency DC-DC conversion applications. In Zero voltage switching converter, turn on & turn off of a switch occurs at zero voltage that results in lower switching losses. In this converter soft switching is achieved by using resonant components. The optimal values of resonant components are determined by using electric functions derived from circuit configuration. This type of soft switched resonant converter offers very low electromagnetic interference (EMI.This study presents the circuit configuration with least components to realize highly efficient zero voltage switching resonant converter. It’s feasibility is confirmed with the developed proto type model and experimental results are verified.

  9. Ignition studies in support of the European High Power Laser Energy Research Facility project

    Indian Academy of Sciences (India)

    J Pasley

    2010-11-01

    The European High Power Laser Energy Research Facility (HiPER) project is one of a number of large-scale scientific infrastructure projects supported by the European Commission’s Seventh Framework Programme (FP7). Part of this project involves the development of a target area for the exploration of inertial fusion energy. This paper describes some of the research that is being carried out by the author in support of this aspect of the program. The effects of different regions of the fusion target mixing prior to thermonuclear ignition have been investigated using the 1D Lagrangian radiation hydrodynamics simulation code HYADES. Results suggest that even low (few parts per million) levels of contamination of fuel by high- ion species may inhibit ignition due to radiative cooling of the ignition spot.

  10. Research and development of neodymium phosphate laser glass for high power laser application

    Science.gov (United States)

    Hu, Lili; He, Dongbing; Chen, Huiyu; Wang, Xin; Meng, Tao; Wen, Lei; Hu, Junjiang; Xu, Yongchun; Li, Shunguang; Chen, Youkuo; Chen, Wei; Chen, Shubin; Tang, Jingping; Wang, Biao

    2017-01-01

    Neodymium phosphate laser glass is a key optical element for high-power laser facility. In this work, the latest research and development of neodymium phosphate laser glass at the Shanghai Institute of Optics and Fine Mechanics (SIOM), China, is addressed. Neodymium phosphate laser glasses, N31, N41, NAP2, and NAP4, for high peak power and high average power applications have been developed. The properties of these glasses are presented and compared to those of other commercial neodymium phosphate laser glass from the Schott and Hoya companies and the Vavilov State Optical Institute (GOI), Russia. Continuous melting and edge cladding are the two key fabrication techniques that are used for the mass production of neodymium phosphate laser glass slabs. These techniques for the fabrication of large-aperture N31 neodymium phosphate laser glass slabs with low stress birefringence and residual reflectivity have been developed by us The effect of acid etching on the microstructure, optical transmission, and mechanical properties of NAP2 glass is also discussed.

  11. Research and development of neodymium phosphate laser glass for high power laser application

    Science.gov (United States)

    Hu, Lili; He, Dongbing; Chen, Huiyu; Wang, Xin; Meng, Tao; Wen, Lei; Hu, Junjiang; Xu, Yongchun; Li, Shunguang; Chen, Youkuo; Chen, Wei; Chen, Shubin; Tang, Jingping; Wang, Biao

    2016-12-01

    Neodymium phosphate laser glass is a key optical element for high-power laser facility. In this work, the latest research and development of neodymium phosphate laser glass at the Shanghai Institute of Optics and Fine Mechanics (SIOM), China, is addressed. Neodymium phosphate laser glasses, N31, N41, NAP2, and NAP4, for high peak power and high average power applications have been developed. The properties of these glasses are presented and compared to those of other commercial neodymium phosphate laser glass from the Schott and Hoya companies and the Vavilov State Optical Institute (GOI), Russia. Continuous melting and edge cladding are the two key fabrication techniques that are used for the mass production of neodymium phosphate laser glass slabs. These techniques for the fabrication of large-aperture N31 neodymium phosphate laser glass slabs with low stress birefringence and residual reflectivity have been developed by us The effect of acid etching on the microstructure, optical transmission, and mechanical properties of NAP2 glass is also discussed.

  12. Research on Power Producer’s Bidding Behavior Based on the Best-Response Dynamic Model

    Directory of Open Access Journals (Sweden)

    Jingqi Sun

    2014-01-01

    Full Text Available As China’s electricity market is facing many problems, the research on power producer’s bidding behavior can promote the healthy and sustainable development of China’s electricity market. As a special commodity, the “electricity” possesses complicated production process. The instable market constraint condition, nonsymmetric information, and a lot of random factors make the producer’s bidding process more complex. Best-response dynamic is one of the classic dynamic mechanisms of the evolutionary game theory, which applies well in the repeated game and strategy evolution that happen among a few bounded rational players with a quick learning capability. The best-response dynamic mechanism is employed to study the power producer’s bidding behavior in this paper, the producer’s best-response dynamic model is constructed, and how the producers would engage in bidding is analyzed in detail. Taking two generating units in South China regional electricity market as the example, the producer’s bidding behavior by following the producer’s best-response dynamic model is verified. The relationships between the evolutionarily stable strategy (ESS of power producer’s bidding and the market demand, and ceiling and floor price as well as biding frequency are discussed in detail.

  13. Solid-State 2MW Klystron Power Control System

    CERN Document Server

    Kempkes, Michael; Gaudreau, Marcel; Hawkey, Timothy; Roth, Ian

    2005-01-01

    Under an SBIR effort for the DOE, Diversified Technologies, Inc. designed, built, and installed a solid state power control system for the Advanced Light Source klystrons at Argonne National Laboratory (ANL). This system consists of two major elements - a 100 kV, 20 A CW solid state series switch, and a solid state voltage regulator for the mod-anode of the klystron. The series switch replaces the existing mercury ignitron crowbar, eliminating these environmentally hazardous components while providing enhanced arc protection and faster return to transmit. The mod-anode voltage regulator uses series IGBTs, operating in the linear regime, to provide highly rapid and accurate control of the mod-anode voltage, and therefore the output power from the klystron. Results from the installation and testing of this system at ANL will be presented.

  14. A Study of Pioneer Vegetation Communities along a power line clearing at the Patuxent Wildlife Research Center

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — In 1960 a strip of forest at the Patuxent Wildlife Research Center was clear-cut to establish a high tension power line. Almost all vegetation was removed and the...

  15. Advanced virtual energy simulation training and research: IGCC with CO2 capture power plant

    Energy Technology Data Exchange (ETDEWEB)

    Zitney, S.; Liese, E.; Mahapatra, P.; Bhattacharyya, D.; Provost, G.

    2011-01-01

    In this presentation, we highlight the deployment of a real-time dynamic simulator of an integrated gasification combined cycle (IGCC) power plant with CO{sub 2} capture at the Department of Energy's (DOE) National Energy Technology Laboratory's (NETL) Advanced Virtual Energy Simulation Training and Research (AVESTARTM) Center. The Center was established as part of the DOE's accelerating initiative to advance new clean coal technology for power generation. IGCC systems are an attractive technology option, generating low-cost electricity by converting coal and/or other fuels into a clean synthesis gas mixture in a process that is efficient and environmentally superior to conventional power plants. The IGCC dynamic simulator builds on, and reaches beyond, conventional power plant simulators to merge, for the first time, a 'gasification with CO{sub 2} capture' process simulator with a 'combined-cycle' power simulator. Fueled with coal, petroleum coke, and/or biomass, the gasification island of the simulated IGCC plant consists of two oxygen-blown, downward-fired, entrained-flow, slagging gasifiers with radiant syngas coolers and two-stage sour shift reactors, followed by a dual-stage acid gas removal process for CO{sub 2} capture. The combined cycle island consists of two F-class gas turbines, steam turbine, and a heat recovery steam generator with three-pressure levels. The dynamic simulator can be used for normal base-load operation, as well as plant start-up and shut down. The real-time dynamic simulator also responds satisfactorily to process disturbances, feedstock blending and switchovers, fluctuations in ambient conditions, and power demand load shedding. In addition, the full-scope simulator handles a wide range of abnormal situations, including equipment malfunctions and failures, together with changes initiated through actions from plant field operators. By providing a comprehensive IGCC operator training system, the

  16. The Application of High-Efficient Reverse Osmosis Wastewater Treatment in The Zero-Emission of Power Plant%高效反渗透废水处理工艺在电厂废水零排放中的应用

    Institute of Scientific and Technical Information of China (English)

    胡小武

    2011-01-01

    Industrial wastewater treatment system has become more and more widely applied in enterprise of wastewater treatment,Shenhua billion the power plant using high reverse osmosis wastewater treatment process system,For power plant in various industrial wastewater treatment,Thus reach wastewater recirculation using,realized the wastewater zero discharge.%工业废水处理工艺系统越来越广泛应用于企业的废水处理中。神华亿利煤矸石电厂利用高效反渗透废水处理工艺系统,对电厂中的各种工业废水进行处理,从而达到废水再循环利用,实现了废水零排放。

  17. Data base on dose reduction research projects for nuclear power plants. Volume 5

    Energy Technology Data Exchange (ETDEWEB)

    Khan, T.A.; Yu, C.K.; Roecklein, A.K. [Brookhaven National Lab., Upton, NY (United States)

    1994-05-01

    This is the fifth volume in a series of reports that provide information on dose reduction research and health physics technology or nuclear power plants. The information is taken from two of several databases maintained by Brookhaven National Laboratory`s ALARA Center for the Nuclear Regulatory Commission. The research section of the report covers dose reduction projects that are in the experimental or developmental phase. It includes topics such as steam generator degradation, decontamination, robotics, improvements in reactor materials, and inspection techniques. The section on health physics technology discusses dose reduction efforts that are in place or in the process of being implemented at nuclear power plants. A total of 105 new or updated projects are described. All project abstracts from this report are available to nuclear industry professionals with access to a fax machine through the ACEFAX system or a computer with a modem and the proper communications software through the ACE system. Detailed descriptions of how to access all the databases electronically are in the appendices of the report.

  18. Coated particle fuel for radioisotope power systems and heater units: status and future research needs

    Science.gov (United States)

    El-Genk, Mohamed S.; Tournier, Jean-Michel; Sholtis, Joseph A.; Lipinski, Ronald J.

    2000-01-01

    Coated particle fuel has been proposed recently for use in Radioisotope Power Systems (RPSs) and Radioisotope Heater Units (RHUs) for a variety of space missions requiring power levels from mWs to 10's or even hundreds of Watts. It can be made into different shapes and sizes of solid compacts, heating tapes, or paints. Using a conservative design approach, this fuel form could increase by 2.3-2.4 times the thermal power output of a LWRHU, while offering promise of enhanced safety. These performance figures are based on using single-size (500 μm) compacts of ZrC coated 238PuO2 kernels and assuming 10% and 5% He release, respectively, at 1723 K, following 10 years of storage. Using binary-size (300 and 1200 μm) fuel kernels in the compact increases the thermal power output by an additional 15%. 238PuO2 fuel kernels are intentionally sized (>=300 μm in diameter) to prevent any adverse radiological effects. They are non-respirable and non-inhalable and, if ingested, would simply be excreted with no radiological effects. The 238PuO2 fuel kernels are contained within a strong ZrC coating, which is designed to fully retain the fuel and the helium gas. Helium retention in large grain (>=300 μm) granular and polycrystalline fuel kernels is possible even at high temperatures (>1700 K). The former could be fabricated using binderless agglomeration or similar processes, while the latter could be fabricated using Sol-Gel or thermal plasma processes, with potentially less radioactive waste and fabrication contamination. In addition to summarizing the results of a recent effort investigating the performance of coated fuel particle compact (CPFC) and helium gas release, this paper identifies and discusses future research and testing needs. .

  19. Power up-grading study for the first Egyptian research reactor

    Energy Technology Data Exchange (ETDEWEB)

    El-Sawy Temraz, H.; Ashoub, N. E-mail: nageeb@pcn.aea.sci.eg; Fathallah, A

    2001-09-01

    In the present work, power up-grading study is performed, for the first Egyptian Research Reactor (ET-RR-1), using the present fuel basket with 4x4 fuel rods, (17.5 mm pitch), and a proposed fuel basket with 5x5 fuel rods, (14.0 mm pitch), without violating the thermal hydraulic safety criteria. These safety criteria are; fuel centerline temperature (fuel melting), clad surface temperature (surface boiling), outlet coolant temperature, and maximum heat flux (critical heat flux ratio). Different thermal reactor powers (2-10 MW) and different core coolant flow rates (450, 900, 1350 m{sup 3} h{sup -1}) are considered. The thermal hydraulic analysis was performed using the subchannel code COBRA-IIIC for the estimation of temperatures, coolant velocities and critical heat flux. The neutronic calculations were performed using WIMS-D4 code with 5-group neutron cross section library. These cross sections were adapted to use in the two-dimensional (2-D) diffusion code DIXY for core calculations. The study concluded that ET-RR-1 power can be upgraded safely up to 4 MW with the present 4x4-fuel basket and with the proposed 5x5-fuel basket up to 5 MW with the present coolant flow rate (900 m{sup 3} h{sup -1}). With the two fuel arrays, the reactor power can be upgraded to 6 MW with coolant flow rate of 1350 m{sup 3} h{sup -1} without violating the safety criterion. It is also concluded that, loading the ET-RR-1 core with the proposed fuel basket (5x5) increases the excess reactivity of the reactor core than the present 4x4 fuel matrix with equal U-235 mass load and gave better fuel economy of fuel utilization.

  20. Logic circuits from zero forcing.

    Science.gov (United States)

    Burgarth, Daniel; Giovannetti, Vittorio; Hogben, Leslie; Severini, Simone; Young, Michael

    We design logic circuits based on the notion of zero forcing on graphs; each gate of the circuits is a gadget in which zero forcing is performed. We show that such circuits can evaluate every monotone Boolean function. By using two vertices to encode each logical bit, we obtain universal computation. We also highlight a phenomenon of "back forcing" as a property of each function. Such a phenomenon occurs in a circuit when the input of gates which have been already used at a given time step is further modified by a computation actually performed at a later stage. Finally, we show that zero forcing can be also used to implement reversible computation. The model introduced here provides a potentially new tool in the analysis of Boolean functions, with particular attention to monotonicity. Moreover, in the light of applications of zero forcing in quantum mechanics, the link with Boolean functions may suggest a new directions in quantum control theory and in the study of engineered quantum spin systems. It is an open technical problem to verify whether there is a link between zero forcing and computation with contact circuits.

  1. Liquid metal technology for concentrated solar power systems: Contributions by the German research program

    Directory of Open Access Journals (Sweden)

    Thomas Wetzel

    2014-03-01

    Full Text Available Concentrated solar power (CSP systems can play a major role as a renewable energy source with the inherent possibility of including a thermal energy storage subsystem for improving the plant dispatchability. Next-generation CSP systems have to provide an increased overall efficiency at reduced specific costs and they will require higher operating temperatures and larger heat flux densities. In that context, liquid metals are proposed as advanced high temperature heat transfer fluids, particularly for central receiver systems. Their main advantages are chemical stability at temperatures up to 900 ℃ and even beyond, as well as largely improved heat transfer when compared to conventional fluids like oil or salt mixtures, primarily due to their superior thermal conductivity. However, major issues here are the corrosion protection of structural materials and the development of technology components and control systems, as well as the development of indirect storage solutions, to circumvent the relatively small heat capacity of liquid metals. On the other hand, using liquid metals might enable alternative technologies like direct thermal-electric conversion or use of solar high-tem­perature heat in chemical processes. This article aims at describing research areas and research needs to be addressed for fully evaluating and subsequently utilizing the potential of liquid metals in CSP systems. A second aim of the article is a brief overview of the liquid metal research capabilities of Karlsruhe Institute of Technology (KIT, their background and their relation to CSP and the aforementioned research pathways.

  2. 地区电网无功优化研究%Regional power grid reactive power optimization research

    Institute of Scientific and Technical Information of China (English)

    张小敏; 林晓宇; 黄良俊; 吴信文; 郑健睿; 刘苏云

    2014-01-01

    为了更有效快速的处理电力系统配网无功优化问题,文中建立了配电网无功优化的数学模型,利用改进遗传算法以网损目标函数,以无功平衡、电压合格等为约束条件,通过使用PSASP仿真软件对山东某市的电网进行仿真模拟,证明方案的正确性和实际可行性。%In order to more effectively deal with power system distribution reactive- power optimization problem, reactive- power optimization mathematical model is established. This model uses the minimum network losses as the objective function and takes reactive power balance, satisfaction voltage quality as the constraints. By using PSASP simulation software to simulation a city in Shandong power grid and prove the correctness and practical feasibility.

  3. Tokamak power systems studies, FY 1985

    Energy Technology Data Exchange (ETDEWEB)

    Baker, C.C.; Brooks, J.N.; Ehst, D.A.; Smith, D.L.; Sze, D.K.

    1985-12-01

    The Tokamak Power System Studies (TPSS) at ANL in FY-1985 were devoted to exploring innovative design concepts which have the potential for making substantial improvements in the tokamak as a commercial power reactor. Major objectives of this work included improved reactor economics, improved environmental and safety features, and the exploration of a wide range of reactor plant outputs with emphasis on reduced plant sizes compared to STARFIRE. The activities concentrated on three areas: plasma engineering, impurity control, and blanket/first wall/shield technology. 205 refs., 125 figs., 107 tabs.

  4. Technical Feasibility Study for Zero Energy K-12 Schools

    Energy Technology Data Exchange (ETDEWEB)

    Bonnema, Eric [National Renewable Energy Lab. (NREL), Golden, CO (United States); Goldwasser, David [National Renewable Energy Lab. (NREL), Golden, CO (United States); Torcellini, Paul [National Renewable Energy Lab. (NREL), Golden, CO (United States); Pless, Shanti [National Renewable Energy Lab. (NREL), Golden, CO (United States); Studer, Daniel [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2016-11-01

    This technical feasibility study provides documentation and research results supporting a possible set of strategies to achieve source zero energy K-12 school buildings as defined by the U.S. Department of Energy (DOE) zero energy building (ZEB) definition (DOE 2015a). Under this definition, a ZEB is an energy-efficient building in which, on a source energy basis, the actual annual delivered energy is less than or equal to the on-site renewable exported energy.

  5. Symmetry realization of texture zeros

    Energy Technology Data Exchange (ETDEWEB)

    Grimus, W. [Institut fuer Theoretische Physik, Universitaet Wien, Boltzmanngasse 5, 1090, Wien (Austria); Joshipura, A.S. [Physical Research Laboratory, 380009, Ahmedabad (India); Lavoura, L. [Centro de Fisica das Interaccoes Fundamentais, Instituto Superior Tecnico, Universidade Tecnica de Lisboa, 1049-001, Lisboa (Portugal); Tanimoto, M. [Department of Physics, Niigata University, Ikarashi 2-8050, 950-2181, Niigata (Japan)

    2004-08-01

    We show that it is possible to enforce texture zeros in arbitrary entries of the fermion mass matrices by means of Abelian symmetries; in this way, many popular mass-matrix textures find a symmetry justification. We propose two alternative methods which allow one to place zeros in any number of elements of the mass matrices that one wants. They are applicable simultaneously in the quark and lepton sectors. They are also applicable in grand unified theories. The number of scalar fields required by our methods may be large; still, in many interesting cases this number can be reduced considerably. The larger the desired number of texture zeros is, the simpler are the models which reproduce the texture. (orig.)

  6. Symmetry realization of texture zeros

    CERN Document Server

    Grimus, Walter; Lavoura, L; Tanimoto, M

    2004-01-01

    We show that it is possible to enforce texture zeros in arbitrary entries of the fermion mass matrices by means of Abelian symmetries; in this way, many popular mass-matrix textures find a symmetry justification. We propose two alternative methods which allow to place zeros in any number of elements of the mass matrices that one wants. They are applicable simultaneously in the quark and lepton sectors. They are also applicable in Grand Unified Theories. The number of scalar fields required by our methods may be large; still, in many interesting cases this number can be reduced considerably. The larger the desired number of texture zeros is, the simpler are the models which reproduce the texture.

  7. 移相控制全桥零压零流软开关功率变换器谐振过程分析和参数设计方法%Resonant procedure analysis and parameters design approach for phase-shift controlled full-bridge power converter with zero-voltage and zero-current soft-switching

    Institute of Scientific and Technical Information of China (English)

    夏铸亮; 朱志明; 陈俊杰

    2013-01-01

    移相控制全桥软开关功率变换器广泛应用于各种电弧焊接与切割电源.针对焊接电孤的宽负载工作范围,为实现全负载范围的滞后臂功率器件软开关,对变压器一次侧串联饱和电感和隔直电容的移相控制全桥软开关功率变换器的谐振工作过程进行了深入的理论分析,提出实现滞后臂功率器件软开关的饱和电感设计准则,并对不同脉冲宽度和负载电流下的滞后臂功率器件软开关状态进行了仿真研究,验证了理论分析的正确性.在理论分析和仿真研究的基础上,给出了饱和电感总磁通和隔直电容大小的参数设计和选取方法.%The phase -shift controlled full -bridge soft -switching power converter has been widely applied in various electric arc welding and cutting power supplies.Aimed at the wide operating range of welding arc load,the in-depth theoretical analysis is carried out with the resonant procedure of the phase-shift controlled full-bridge soft-switching power converter, in which an saturation inductor and blocking capacitor is connected in series with the primary of transformer, in order to realize the soft-switching of lagging-leg power semiconductors in full load range, and then a design criterion of saturation inductor, to achieved the soft-switching of lagging-leg power semiconductor,is proposed.After that,the simulation study is made to the soft-switching situation of lagging-leg power semiconductors with different pulse width and load current,and the correctness of theoretical analysis is validated.Based on the theoretical analysis and simulation study,the parameters design and selection approach is given for the total magnetic flux of saturation inductor and the value of blocking capacitor.

  8. EMS磁悬浮列车的零电流型永磁电磁混合磁铁设计技术研究%Design of Zero-Power Hybrid Magnet with Permanent Magnets and Electromagnets in EMS Maglev Vehicles

    Institute of Scientific and Technical Information of China (English)

    李云钢; 张晓; 程虎; 刘恒坤

    2011-01-01

    针对EMS磁悬浮列车的零电流型永磁电磁混合磁铁,研究其永磁体和电磁线圈结构参数的设计方法.永磁体安装在磁轭部位,其截面积不受磁极面积的限制,研究得出永磁体的厚度与其截面积的约束关系,并给出永磁重量最小化的设计方法.根据最大平衡安匝数要求,研究得出相对于纯电磁铁,混合磁铁的电磁线圈匝数可减半.由于混合磁铁的可控性能低于纯电磁铁,基于可控性要求,给出修正永磁体的结构参数的方法.最后给出一个实例,将1t负载悬浮在8mm间隙内,所需永磁体仅为6.4 kg.%To design the zero-power hybrid magnet with permanent magnets and electromagnets for EMS maglev vehicles, the structural parameters of its permanent magnets and electromagnets were researched on. The permanent magnet was located at die middte of the yoke, which made its sectional area independent from the area of the pole. The restriction between the thickness and the area of the permanent magnet was presented, and the method of designing the permanent magnet with minimum mass was given. According to the requirements of the maximum balance ampere-turn, it was concluded that the ampere-turn of the hybrid magnet can be reduced to half of that of the pure electromagnet. It was shown that the controllability of the hybrid magnet is always weaker than that of the pure electromagnet, and then a revision of the design for the permanent magnet was proposed based on the requirement of the controllability. Finally, a design example of the hybrid magnet was presented with 11 load suspending at 8 mm, and the mass of the permanent magnet was only 6.4 kg.

  9. Practical superconductor development for electrical power applications. Quarterly report for the period ending June 30, 2000

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-07-21

    This is a multiyear experimental research program focused on improving relevant material properties of high-{Tc} superconductors (HTSs) and on development of fabrication methods that can be transferred to industry for production of commercial conductors. The development of teaming relationships through agreements with industrial partners is a key element of the Argonne (ANL) program.

  10. Practical superconductor development for electrical power applications - quarterly report for the period ending Dec. 31, 2003.

    Energy Technology Data Exchange (ETDEWEB)

    Dorris, S. E.

    2004-03-02

    This is a multiyear experimental research program that focuses on improving relevant material properties of high-critical temperature (Tc) superconductors and developing fabrication methods that can be transferred to industry for production of commercial conductors. The development of teaming relationships through agreements with industrial partners is a key element of the Argonne National Laboratory (ANL) program.

  11. Practical superconductor development for electrical power applications - quarterly report for the period ending March 31, 2004.

    Energy Technology Data Exchange (ETDEWEB)

    Dorris, S. E.

    2004-07-21

    This is a multiyear experimental research program that focuses on improving relevant material properties of high-critical-temperature (Tc) superconductors and developing fabrication methods that can be transferred to industry for production of commercial conductors. The development of teaming relationships through agreements with industrial partners is a key element of the Argonne National Laboratory (ANL) program.

  12. Practical superconductor development for electrical power applications - quarterly report for the period ending June 30, 2004.

    Energy Technology Data Exchange (ETDEWEB)

    Dorris, S. E.

    2004-09-09

    This is a multiyear experimental research program that focuses on improving relevant material properties of high-critical-temperature (Tc) superconductors and developing fabrication methods that can be transferred to industry for production of commercial conductors. The development of teaming relationships through agreements with industrial partners is a key element of the Argonne National Laboratory (ANL) program.

  13. Research on Safety and Stability of Regional Power Grids to the Year 2020

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    The safety and stability study on Northeast, North, East, Northwest and Central China power grids had been carried out, which provided technical supports to planning design of regional power grids. By analyzing safety and stability under severe faults in regional power grids, revealed weaknesses on power grid configurations and measures for preventing from loss of stability were presented. In comparison of various schemes of power system safety and stability among parts of power grids, more than two recommended schemes can be chosen as reference in planning design for regional power grids. Considering the safety and stability control measures necessary for each power grids, it is believed the trunk networks of all power grids can fulfill the third criteria of Guideline for Power System Safety and Stability, while the weakness and predominated hydropower may deteriorate safety and stability of power grids. The power grid shall be regulated in line with the variation of boundary conditions.

  14. Combining the power of stories and the power of numbers: mixed methods research and mixed studies reviews.

    Science.gov (United States)

    Pluye, Pierre; Hong, Quan Nha

    2014-01-01

    This article provides an overview of mixed methods research and mixed studies reviews. These two approaches are used to combine the strengths of quantitative and qualitative methods and to compensate for their respective limitations. This article is structured in three main parts. First, the epistemological background for mixed methods will be presented. Afterward, we present the main types of mixed methods research designs and techniques as well as guidance for planning, conducting, and appraising mixed methods research. In the last part, we describe the main types of mixed studies reviews and provide a tool kit and examples. Future research needs to offer guidance for assessing mixed methods research and reporting mixed studies reviews, among other challenges.

  15. (Re)considering Foucault for science education research: considerations of truth, power and governance

    Science.gov (United States)

    Bazzul, Jesse; Carter, Lyn

    2017-03-01

    This article is a response to Anna Danielsonn, Maria Berge, and Malena Lidar's paper, "Knowledge and power in the technology classroom: a framework for studying teachers and students in action", and an appeal to science educators of all epistemological orientations to (re)consider the work of Michel Foucault for research in science education. Although this essay does not come close to outlining the importance of Foucault's work for science education, it does present a lesser-known side of Foucault as an anti-polemical, realist, modern philosopher interested in the way objective knowledge is entangled with governance in modernity. This latter point is important for science educators, as it is the intersection of objective knowledge and institutional imperatives that characterizes the field(s) of science education. Considering the lack of engagement with philosophy and social theory in science education, this paper offers one of many possible readings of Foucault (we as authors have also published different readings of Foucault) in order to engage crucial questions related to truth, power, governance, discourse, ethics and education.

  16. The potential application and challenge of powerful CRISPR/Cas9 system in cardiovascular research.

    Science.gov (United States)

    Li, Yangxin; Song, Yao-Hua; Liu, Bin; Yu, Xi-Yong

    2017-01-15

    CRISPR/Cas9 is a precision-guided munition found in bacteria to fight against invading viruses. This technology has enormous potential applications, including altering genes in both somatic and germ cells, as well as generating knockout animals. Compared to other gene editing techniques such as zinc finger nucleases and TALENS, CRISPR/Cas9 is much easier to use and highly efficient. Importantly, the multiplex capacity of this technology allows multiple genes to be edited simultaneously. CRISPR/Cas9 also has the potential to prevent and cure human diseases. In this review, we wish to highlight some key points regarding the future prospect of using CRISPR/Cas9 as a powerful tool for cardiovascular research, and as a novel therapeutic strategy to treat cardiovascular diseases.

  17. Status of HiLASE project: High average power pulsed DPSSL systems for research and industry

    Directory of Open Access Journals (Sweden)

    Mocek T.

    2013-11-01

    Full Text Available We introduce the Czech national R&D project HiLASE which focuses on strategic development of advanced high-repetition rate, diode pumped solid state laser (DPSSL systems that may find use in research, high-tech industry and in the future European large-scale facilities such as HiPER and ELI. Within HiLASE we explore two major concepts: thin-disk and cryogenically cooled multislab amplifiers capable of delivering average output powers above 1 kW level in picosecond-to-nanosecond pulsed regime. In particular, we have started a programme of technology development to demonstrate the scalability of multislab concept up to the kJ level at repetition rate of 1–10 Hz.

  18. Wind power research at Oregon State University. [for selecting windpowered machinery sites

    Science.gov (United States)

    Hewson, E. W.

    1973-01-01

    There have been two primary thrusts of the research effort to date, along with several supplementary ones. One primary area has been an investigation of the wind fields along coastal areas of the Pacific Northwest, not only at the shoreline but also for a number of miles inland and offshore as well. Estimates have been made of the influence of the wind turbulence as measured at coastal sites in modifying the predicted dependence of power generated on the cube of the wind speed. Wind flow patterns in the Columbia River valley have also been studied. The second primary thrust has been to substantially modify and improve an existing wind tunnel to permit the build up of a boundary layer in which various model studies will be conducted. One of the secondary studies involved estimating the cost of building an aerogenerator.

  19. Misuse of "Power" and Other Mechanical Terms in Sport and Exercise Science Research.

    Science.gov (United States)

    Winter, Edward M; Abt, Grant; Brookes, F B Carl; Challis, John H; Fowler, Neil E; Knudson, Duane V; Knuttgen, Howard G; Kraemer, William J; Lane, Andrew M; van Mechelen, Willem; Morton, R Hugh; Newton, Robert U; Williams, Clyde; Yeadon, M R

    2016-01-01

    Despite the Système International d'Unitès (SI) that was published in 1960, there continues to be widespread misuse of the terms and nomenclature of mechanics in descriptions of exercise performance. Misuse applies principally to failure to distinguish between mass and weight, velocity and speed, and especially the terms "work" and "power." These terms are incorrectly applied across the spectrum from high-intensity short-duration to long-duration endurance exercise. This review identifies these misapplications and proposes solutions. Solutions include adoption of the term "intensity" in descriptions and categorizations of challenge imposed on an individual as they perform exercise, followed by correct use of SI terms and units appropriate to the specific kind of exercise performed. Such adoption must occur by authors and reviewers of sport and exercise research reports to satisfy the principles and practices of science and for the field to advance.

  20. Electric Power Research Institute, Environmental Control Technology Center monthly report to the Steering Committee, June 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-11-02

    Operations and maintenance continued this month at the Electric Power Research Institute`s Environmental Control Technology Center. Testing on the 4.0 MW Pilot FGD unit continued this month with High Velocity Scrubbing and the Tampa Electric Company (TECO) Tailored Collaboration test block. Additionally, Phase III of the Toxics Removal/Carbon Injection test block was conducted concurrently with FGD testing. At the beginning of the month, a second phase of third-party testing began for Suncor, Inc. The Suncor Gypsum Sample Collection test block (MSUN) began on June 5 on the 0.4 MW Mini-Pilot Wet FGD unit. Testing was completed on June 13. On the Cold-Side Selective Catalytic Reduction (SCR) unit, testing continued this month as ammonia slip measurements were conducted under low catalyst inlet temperatures and at baseline conditions.

  1. Research on pressure control of pressurizer in pressurized water reactor nuclear power plant

    Science.gov (United States)

    Dai, Ling; Yang, Xuhong; Liu, Gang; Ye, Jianhua; Qian, Hong; Xue, Yang

    2010-07-01

    Pressurizer is one of the most important components in the nuclear reactor system. Its function is to keep the pressure of the primary circuit. It can prevent shutdown of the system from the reactor accident under the normal transient state while keeping the setting value in the normal run-time. This paper is mainly research on the pressure system which is running in the Daya Bay Nuclear Power Plant. A conventional PID controller and a fuzzy controller are designed through analyzing the dynamic characteristics and calculating the transfer function. Then a fuzzy PID controller is designed by analyzing the results of two controllers. The fuzzy PID controller achieves the optimal control system finally.

  2. Handbook of nuclear power plant seismic fragilities, Seismic Safety Margins Research Program

    Energy Technology Data Exchange (ETDEWEB)

    Cover, L.E.; Bohn, M.P.; Campbell, R.D.; Wesley, D.A.

    1983-12-01

    The Seismic Safety Margins Research Program (SSMRP) has a gola to develop a complete fully coupled analysis procedure (including methods and computer codes) for estimating the risk of an earthquake-induced radioactive release from a commercial nuclear power plant. As part of this program, calculations of the seismic risk from a typical commercial nuclear reactor were made. These calculations required a knowledge of the probability of failure (fragility) of safety-related components in the reactor system which actively participate in the hypothesized accident scenarios. This report describes the development of the required fragility relations and the data sources and data reduction techniques upon which they are based. Both building and component fragilities are covered. The building fragilities are for the Zion Unit 1 reactor which was the specific plant used for development of methodology in the program. Some of the component fragilities are site-specific also, but most would be usable for other sites as well.

  3. The maximum power efficiency 1-√τ: Research, education, and bibliometric relevance

    Science.gov (United States)

    Calvo Hernández, A.; Roco, J. M. M.; Medina, A.; Velasco, S.; Guzmán-Vargas, L.

    2015-07-01

    The well-known efficiency at maximum power for a cyclic system working between hot T h and low T c temperatures given by the equation 1-√ τ( τ= T c /T h), has become a landmark result with regards to the thermodynamic optimization of a great variety of energy converters. Its wide applicability and sole dependence on the external heat bath temperatures (as the Carnot efficiency does) allows for an easy comparison with experimental efficiencies leading to a striking fair agreement. Reversible, finite-time, and linear-irreversible derivations are analyzed in order to show a broader perspective about its meaning from both researching and pedagogical point of views. Its scientific relevance and historical development are also analyzed in this work by means of some bibliometric data. This article is supplemented with comments by Hong Qian and a final reply by the authors.

  4. Research integrity and rights of indigenous peoples: appropriating Foucault's critique of knowledge/power.

    Science.gov (United States)

    Swazo, Norman K

    2005-09-01

    In this paper I appropriate the philosophical critique of Michel Foucault as it applies to the engagement of Western science and indigenous peoples in the context of biomedical research. The science of population genetics, specifically as pursued in the Human Genome Diversity Project, is the obvious example to illustrate (a) the contraposition of modern science and 'indigenous science', (b) the tendency to depreciate and marginalize indigenous knowledge systems, and (c) the subsumption of indigenous moral preferences in the juridical armature of international human rights law. I suggest that international bioethicists may learn from Foucault's critique, specifically of the need for vigilance about the knowledge/power relation expressed by the contraposition of modern science and 'indigeneity'.

  5. Solving discrete zero point problems

    NARCIS (Netherlands)

    van der Laan, G.; Talman, A.J.J.; Yang, Z.F.

    2004-01-01

    In this paper an algorithm is proposed to .nd a discrete zero point of a function on the collection of integral points in the n-dimensional Euclidean space IRn.Starting with a given integral point, the algorithm generates a .nite sequence of adjacent integral simplices of varying dimension and termi

  6. Stepping Back from Zero Tolerance

    Science.gov (United States)

    Browne-Dianis, Judith

    2011-01-01

    Schools' use of zero tolerance policies has been increasing since the 1980s as part of a societal movement to crack down on drug abuse and violence among youth. But far from making schools safer, this harsh, inflexible approach to discipline has been eroding the culture of schools and creating devastating consequences for children, writes…

  7. Wild radical square zero algebras

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    It is shown that a radical square zero algebra is wild, if and only if it is of Corner's type, and it is strictly wild if and only if it is Endo-wild. This gives a negative answer to a problem posed by Simson.

  8. Local stretch zeroing NMO correction

    Science.gov (United States)

    Kazemi, N.; Siahkoohi, H. R.

    2012-01-01

    In this paper we present a new method of normal move-out (NMO) correction called local stretch zeroing (LSZ) method that avoids NMO stretch. The method eliminates the theoretical curves that generate interpolated data samples responsible for NMO stretch. Pre-correction time sampling interval is preserved by reassigning and zero padding of true data samples. The optimum mute zone selection feature of the LSZ method eliminates all interfering reflection events at far offsets. The resulted stacked section from the LSZ method contains generally higher frequency components than a normal stack, and preserves most of the shallow reflectors. The LSZ method requires that zero-offset width of the time gate, i.e. zero-offset time difference between two adjacent reflections, be larger than the dominant period. The major shortcoming of the method occurs when CMP data are over- or under-NMO corrected. Both synthetic and real world examples show the efficiency of the LSZ method over the conventional NMO (CNMO) correction. The method loses its superiority when CMP data are over- or under-NMO corrected.

  9. Questioning Zero and Negative Numbers

    Science.gov (United States)

    Wilcox, Virginia B.

    2008-01-01

    After experiencing a Developing Mathematical Ideas (DMI) class on the construction of algebraic concepts surrounding zero and negative numbers, the author conducted an interview with a first grader to determine the youngster's existing level of understanding about these topics. Uncovering young students' existing understanding can provide focus…

  10. Advances in Zero-Field Nuclear Magnetic Resonance Spectroscopy

    OpenAIRE

    Theis, Thomas

    2012-01-01

    In the course of the last century, Nuclear magnetic resonance (NMR) has become a powerful and ubiquitous analytical tool for the determination of molecular identity, structure, and function. Traditionally, the great analytical power of NMR comes at the cost of mobility and large expenses for cryogenic cooling. This thesis presents how zero-field NMR detected with an atomic magnetometer is emerging as a new, potentially portable and cost-effective modality of NMR with the ability of providing ...

  11. A synthetic zero air standard

    Science.gov (United States)

    Pearce, Ruth

    2016-04-01

    A Synthetic Zero Air Standard R. E. Hill-Pearce, K. V. Resner, D. R. Worton, P. J. Brewer The National Physical Laboratory Teddington, Middlesex TW11 0LW UK We present work towards providing traceability for measurements of high impact greenhouse gases identified by the World Meteorological Organisation (WMO) as critical for global monitoring. Standards for these components are required with challengingly low uncertainties to improve the quality assurance and control processes used for the global networks to better assess climate trends. Currently the WMO compatibility goals require reference standards with uncertainties of < 100 nmolmol-1 for CO2 (northern hemisphere) and < 2 nmolmol-1 for CH4 and CO. High purity zero gas is required for both the balance gas in the preparation of reference standards and for baseline calibrations of instrumentation. Quantification of the amount fraction of the target components in the zero gas is a significant contributor to the uncertainty and is challenging due to limited availability of reference standard at the amount fraction of the measurand and limited analytical techniques with sufficient detection limits. A novel dilutor was used to blend NPL Primary Reference Gas Mixtures containing CO2, CH4 and CO at atmospheric amount fractions with a zero gas under test. Several mixtures were generated with nominal dilution ratios ranging from 2000:1 to 350:1. The baseline of two cavity ring down spectrometers was calibrated using the zero gas under test after purification by oxidative removal of CO and hydrocarbons to < 1 nmolmol-1 (SAES PS15-GC50) followed by the removal of CO2 and water vapour to < 100 pmolmol-1 (SAES MC190). Using the standard addition method.[1] we have quantified the amount fraction of CO, CO2, and CH4 in scrubbed whole air (Scott Marrin) and NPL synthetic zero air. This is the first synthetic zero air standard with a matrix of N2, O2 and Ar closely matching ambient composition with gravimetrically assigned

  12. Distribution-free Inference of Zero-inated Binomial Data for Longitudinal Studies.

    Science.gov (United States)

    He, H; Wang, W J; Hu, J; Gallop, R; Crits-Christoph, P; Xia, Y L

    2015-10-01

    Count reponses with structural zeros are very common in medical and psychosocial research, especially in alcohol and HIV research, and the zero-inflated poisson (ZIP) and zero-inflated negative binomial (ZINB) models are widely used for modeling such outcomes. However, as alcohol drinking outcomes such as days of drinkings are counts within a given period, their distributions are bounded above by an upper limit (total days in the period) and thus inherently follow a binomial or zero-inflated binomial (ZIB) distribution, rather than a Poisson or zero-inflated Poisson (ZIP) distribution, in the presence of structural zeros. In this paper, we develop a new semiparametric approach for modeling zero-inflated binomial (ZIB)-like count responses for cross-sectional as well as longitudinal data. We illustrate this approach with both simulated and real study data.

  13. Pedagogical development and technical research in the area of geothermal power production

    OpenAIRE

    Denbow, Christopher

    2011-01-01

    This work describes the types of power plants used for geothermal power generation in the world; the dry steam power plant, the flash steam power plant and the binary cycle power plant. The objective of the MSc work was the development of learning content on the subject of geothermal power generation for the CompEdu platform in the energy department at KTH. The power plants are described from a system perspective followed by an explanation of the operation of major components. Examples and ca...

  14. Analysis on Zero Power Experiment of High Flux Engineering Test Reactor with Three-Dimensional Continuous Energy Monte Carlo Code%三维堆芯连续能量蒙特卡罗程序用于HFETR零功率物理实验计算分析研究

    Institute of Scientific and Technical Information of China (English)

    彭钢

    2012-01-01

    采用三维堆芯连续能量蒙特卡罗程序( MCNP)对高通量工程试验堆(HFETR)零功率物理实验进行计算分析.从计算结果可以看出,在零功率反应堆上,径向铍反射层应当考虑金属铍中的杂质和密度修正,同时需要考虑控制棒过渡段的10B含量修正;而HFETR上的铍块则可以认为是纯金属铍,控制棒过渡段中10B含量也需另作考虑.从计算结果来看,多数参数(堆芯中子有效增殖系数keff、中子通量密度相对分布、γ剂量率相对分布以及多数部件反应性价值)均较好满足误差要求,而个别小反应性部件计算误差较大可能与MCNP程序模型有关.%Three-dimensional, continuous energy Monte Carlo code (MCNP) is adopted to carry out the analysis of zero power experiment of HFETR. From the results, the impurity, density of Beryllium block and the B concentration in control rod transition part should be carefully determined in the analysis of zero power experiment. While in the experiment of HFETR, the Beryllium block is considered as pure metal and the 10B concentration in control rod transition part is different from that of zero power experiment. From the calculation results, these parameters (effective neutron multiplication factor Keff relative distribution of neutron flux density, y dose rate distribution and component reactivity) are quite fit with the experiment. The difference of small reactivity between calculation and experiment is quite large, and may be related to the deficiency of MCNP model.

  15. Zero Accident Vision based strategies in organisations: Innovative perspectives

    NARCIS (Netherlands)

    Zwetsloot, G.I.J.M.; Kines, P.; Wybo, J.L.; Ruotsala, R.; Drupsteen, L.; Bezemer, R.A.

    2017-01-01

    The Zero Accident Vision (ZAV) is a promising approach developed in industry, but not so much addressed by the safety science research community. In a discussion paper in Safety Science (2013) a call was made for more research in this area. Three years later is a good time to take status of developm

  16. Army Net Zero Prove Out. Integrated Net Zero Best Practices

    Science.gov (United States)

    2014-11-18

    Program Office (Office of the Assistant Secretary of the Army for Installations and Environment) 5850 21st Street, Building 211, Second Floor Fort...of energy, water, and waste to capture and commercialize the resource value and/or enhance the ecological productivity of land, water, and air. A...water, and waste to capture and commercialize the resource value and/or enhance the ecological productivity of land, water, and air. A Net Zero

  17. An Overview of NASA Efforts on Zero Boiloff Storage of Cryogenic Propellants

    Science.gov (United States)

    Hastings, Leon J.; Plachta, D. W.; Salerno, L.; Kittel, P.; Haynes, Davy (Technical Monitor)

    2001-01-01

    Future mission planning within NASA has increasingly motivated consideration of cryogenic propellant storage durations on the order of years as opposed to a few weeks or months. Furthermore, the advancement of cryocooler and passive insulation technologies in recent years has substantially improved the prospects for zero boiloff storage of cryogenics. Accordingly, a cooperative effort by NASA's Ames Research Center (ARC), Glenn Research Center (GRC), and Marshall Space Flight Center (MSFC) has been implemented to develop and demonstrate "zero boiloff" concepts for in-space storage of cryogenic propellants, particularly liquid hydrogen and oxygen. ARC is leading the development of flight-type cryocoolers, GRC the subsystem development and small scale testing, and MSFC the large scale and integrated system level testing. Thermal and fluid modeling involves a combined effort by the three Centers. Recent accomplishments include: 1) development of "zero boiloff" analytical modeling techniques for sizing the storage tankage, passive insulation, cryocooler, power source mass, and radiators; 2) an early subscale demonstration with liquid hydrogen 3) procurement of a flight-type 10 watt, 95 K pulse tube cryocooler for liquid oxygen storage and 4) assembly of a large-scale test article for an early demonstration of the integrated operation of passive insulation, destratification/pressure control, and cryocooler (commercial unit) subsystems to achieve zero boiloff storage of liquid hydrogen. Near term plans include the large-scale integrated system demonstration testing this summer, subsystem testing of the flight-type pulse-tube cryocooler with liquid nitrogen (oxygen simulant), and continued development of a flight-type liquid hydrogen pulse tube cryocooler.

  18. Basic Research and Development Effort to Design a Micro Nuclear Power Plant for Brazilian Space Applications

    Science.gov (United States)

    Guimares, L. N. F.; Camillo, G. P.; Placco, G. M.; Barrios, G., A., Jr.; Do Nascimento, J. A.; Borges, E. M.; De Castro Lobo, P. D.

    For some years the Nuclear Energy Division of the Institute for Advanced Studies is conducting the TERRA (Portuguese abbreviation for advanced fast reactor technology) project. This project aims at research and development of the key issues related with nuclear energy applied to space technology. The purpose of this development is to allow future Brazilian space explorers the access of a good and reliable heat, power and/or propulsion system based on nuclear energy. Efforts are being made in fuel and nuclear core design, designing and building a closed Brayton cycle loop for energy conversion, heat pipe systems research for passive space heat rejection, developing computational programs for thermal loop safety analysis and other technology that may be used to improve efficiency and operation. Currently there is no specific mission that requires these technology development efforts; therefore, there is a certain degree of freedom in the organization and development efforts. This paper will present what has been achieved so far, what is the current development status, where efforts are heading and a proposed time table to meet development objectives.

  19. Proton acceleration experiments and warm dense matter research using high power lasers

    Energy Technology Data Exchange (ETDEWEB)

    Roth, M; Alber, I; Guenther, M; Harres, K [Institut fuer Kernphysik, Technische Universitaet Darmstadt, 64289 Darmstadt (Germany); Bagnoud, V [GSI Helmholtzzentrum fuer Schwerionenforschung GmbH, 64291 Darmstadt (Germany); Brown, C R D [Plasma Physics Group, Imperial College London, SW7 2BZ (United Kingdom); Clarke, R; Heathcote, R; Li, B [STFC, Rutherford Appleton Laboratory (RAL), Chilton, Didcot, OX14 OQX (United Kingdom); Daido, H [Photo Medical Research Center, JAEA, Kizugawa-City, Kyoto 619-0215 (Japan); Fernandez, J; Flippo, K; Gaillard, S; Gauthier, C [Los Alamos National Laboratory (LANL), Los Alamos, NM 87545 (United States); Geissel, M [Sandia National Laboratories, Albuquerque, NM 87185 (United States); Glenzer, S; Kritcher, A; Kugland, N; LePape, S [Lawrence Livermore National Laboratory, Livermore, CA 94551 (United States); Gregori, G, E-mail: markus.roth@physik.tu-darmstadt.d [Clarendon Laboratory, University of Oxford, Parks Road, Oxford OX1 3PU (United Kingdom)

    2009-12-15

    The acceleration of intense proton and ion beams by ultra-intense lasers has matured to a point where applications in basic research and technology are being developed. Crucial for harvesting the unmatched beam parameters driven by the relativistic electron sheath is the precise control of the beam. In this paper we report on recent experiments using the PHELIX laser at GSI, the VULCAN laser at RAL and the TRIDENT laser at LANL to control and use laser accelerated proton beams for applications in high energy density research. We demonstrate efficient collimation of the proton beam using high field pulsed solenoid magnets, a prerequisite to capture and transport the beam for applications. Furthermore, we report on two campaigns to use intense, short proton bunches to isochorically heat solid targets up to the warm dense matter state. The temporal profile of the proton beam allows for rapid heating of the target, much faster than the hydrodynamic response time thereby creating a strongly coupled plasma at solid density. The target parameters are then probed by x-ray Thomson scattering to reveal the density and temperature of the heated volume. This combination of two powerful techniques developed during the past few years allows for the generation and investigation of macroscopic samples of matter in states present in giant planets or the interior of the earth.

  20. Aspect of Dynamic Simulation and Experimental Research Studies on Hybrid Pneumatic Power System

    Directory of Open Access Journals (Sweden)

    K. David Huang

    2010-01-01

    Full Text Available A Hybrid Pneumatic Power System (HPPS has been developed for several years with the major aim of reducing the vehicle fuel consumption, environment pollution and enhancing the vehicle performance as well. Comparing with the conventional hybrid system, HPPS replaces the battery's electrochemical energy with a high-pressure air storage tank and enables the internal combustion engine (ICE to function at its sweet spot. Besides, the HPPS, which effectively merges both the high-pressure air flow from the storage tank and the recycled exhaust flow from the ICE, thereby increases the thermal efficiency of the ICE and transforms the merged flow energy into mechanical energy using a high-efficiency turbine. This paper focuses on the major research process into HPPSs, including overall dynamic simulation and experimental validation. By using the simulation tool ITI-Sim, this research demonstrates an experiment which can be operated precisely according to the requirements of various driving conditions under which a car actually runs on the road in accordance with the regulated running vehicle test mode. HPPS is expected to increase the performance of the entire system from 15% to 39%, and is likely to replace the traditional system in the coming years.

  1. Action research for the development of the organizational climate in nuclear power plants. Review of the 6-year research and development program

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, Michio [Kumamoto Univ. (Japan). Faculty of Education; Misumi, Jyuji; Misumi, Emiko; Kotani, Fumio; Fukui, Hirokazu; Sakurai, Yukihiro

    1998-09-01

    The Institute of Nuclear Safety System, Incorporated and the Japan Institute for Group Dynamics have conducted action research for the development of the organizational climate in nuclear power plants. First, two types of scales were completed. One is for measuring the leadership behavior of leaders working at nuclear power plants and the other is for measuring the safety consciousness of workers. After having diagnosed the reality of actual nuclear power plants using those scales developed, leadership training courses were developed and implemented successfully. Analyses of the commitment to organization and self-efficacy and the relationship between leadership and personality were conducted as well. (author)

  2. Space Solar Power Exploratory Research and Technology (SERT) Technical Interchange Meeting 2 (SERT TIM 2)

    Science.gov (United States)

    Howell, Joe; Sanders, Clark W.

    2000-01-01

    The University of Alabama in Huntsville's (UAH) Propulsion Research Center hosted the Space Solar Power Exploratory Research & Technology (SERT) Technical Interchange Meeting TIM) 2 in Huntsville, Alabama December 7-10. 1999 with 126 people in attendance. The SERT program includes both competitively procured activities. which are being implemented through a portfolio of focused R&D investments--with the maximum leveraging of existing resources inside and outside NASA. and guided by these system studies. Axel Roth. Director of the Flight Projects Directorate NASA MSFC, welcomed the SERT TIM 2 participants and challenged them to develop the necessary technologies and demonstrations that will lead to Space Solar Power (SSP) International implementation. Joe Howell, NASA MSFC, reiterated the SERT TIM 2 objectives: 1) Refining and modeling systems approaches for the utilization of SSP concepts and technologies, ranging, from the near-term e.g. for space science, exploration and commercial space applications to the far-term (e. g. SSP for terrestrial markets), including systems concepts, technology, infrastructure (i.g., transportation), and economics. 2) Conducting technology research, development and demonstration activities to produce "proof- of-concept" validation of critical SSP elements for both the nearer and farther-term applications. 3) Initiating partnerships Nationality and Internationally that could be expanded, as appropriate, to pursue later SSP technology and applications (e.g., space science. colonization, etc.). Day one began with the NASA Centers presenting their SERT activities summary since SERT TIM 1 and wound up with a presentation by Masahiro Mori, NASDA titled "NASDA In-house Study for SSP". Demonstration for the Near-Term. Day two began with the SERT Systems Studies and Analysis reports resulting from NRA 8-23 followed by presentations of SERT Technology Demonstrations reports resulting from NRA 8-23. Day two closed with John Mankins presentation

  3. Traffic control data sharing based on ZeroMQ message communication library exchange platform for the research and application%基于ZeroMQ消息通信库的空管数据共享交换平台的研究与应用

    Institute of Scientific and Technical Information of China (English)

    赵一凡

    2016-01-01

    随着军民航事业的快速成长,保证军民航飞行安全的挑战愈发严峻,空中交通管理系统的工作量日渐繁杂,空管数据种类更加繁多,在不同业务之间进行数据通信往往伴随着大量的设计成本却难以达到良好的通信目标。本文对目前消息通信的发展现状做出了分析,提出了目前遇到的问题和需要前进的方向,然后介绍了一种云时代极速消息通信库——ZeroMQ,采用ZeroMQ技术可以降低平台各模块之间的耦合性,并且提高平台的灵活性、可靠性,从而使得平台易维护,最后给出了具体验证。%With the rapid development of military aviation and civil aviation industry and the progress of information technology, workload of air traffic management system is increasingly multifarious, ATC more various data types, data communication between different business is often accompanied by a lot of design cost is difficult to achieve good communication In this paper, the present situation of news communication has made the analysis, put forward the current problems and direction of the need to move forward, and then introduces a speed message communication library ZeroMQ cloud era, ZeroMQ technology can reduce platform by using the coupling between modules, and improve the platform reliability, flexibility so as to make the platform is easy to maintain, in the end, the specific verification was presented.

  4. Maps of zeros of truncated generating functions in high energy collisions

    CERN Document Server

    Brambilla, M; Ugoccioni, R

    2006-01-01

    Theorems on zeros of the truncated generating functions in the complex plane are reviewed and applied to the class of power series distributions. These results, when scrutinized in the framework of the truncated generating function of NB (Pascal) MD type, lead to maps of zeros which are different in correspondence to different classes of events in pp collisions at LHC c.m. energies.

  5. TCT-CSR 功率调节对控制绕组零序过流保护的影响%Impact of TCT-CSR Power Regulation on Zero-sequence Overcurrent Protection of Control Windings

    Institute of Scientific and Technical Information of China (English)

    张芬芬; 郑涛; 刘连光

    2016-01-01

    晶闸管控制变压器式可控并联电抗器(TCT‐CSR)具有功率大范围平滑可调、响应速度快等优势,在超/特高压电网中具有良好的应用前景。以 TCT‐CSR 低压物理模型为研究对象,针对TCT‐CSR 功率快速大幅度调节对本体保护的影响开展研究。根据 TCT‐CSR 结构及原理建立了其稳态运行及功率调节过程的简化数学模型,研究了 TCT‐CSR 功率调节的暂态特性及其对 TCT‐CSR 控制绕组零序过流保护的影响,仿真计算确定了与 TCT‐CSR 功率调节范围对应的控制绕组基波零序电流峰值和暂态持续时间两项指标。在此基础上,提出通过适当增大控制绕组电阻的方法防止本体保护误动,经过大量仿真试验的对比分析,研究确定了电阻阻值的取值范围及其防误动的效果,为 TCT‐CSR 本体参数的设计改进提供了重要参考。%Possessing such advantages as continuously adjustable reactive power and high operating speed , the thyristor controlled transformer‐type controllable shunt reactor ( TCT‐CSR) is preferred to reactive power control in extra/ultra‐high voltage transmission systems . This paper focuses on the impact of power regulation of TCT‐CSR on its protection system . Based on the structure and operating principles of TCT‐CSR , a simplified mathematical model for its operation in both the steady state and transient state during power regulation is proposed . The transient characteristics during power regulation and its influence on zero‐sequence overcurrent protection of control windings are analyzed . The fundamental zero‐sequence current peak value and the transient state duration after power regulation are determined according to simulation results . Based on this , an approach to increasing the resistance of control windings is proposed . The value of the resistor and its influence on the performance of zero‐sequence overcurrent protection

  6. Parallel Error Detection for Leading Zero Anticipation

    Institute of Scientific and Technical Information of China (English)

    Ge Zhang; Wei-Wu Hu; Zi-Chu Qi

    2006-01-01

    The algorithm and its implementation of the leading zero anticipation (LZA) are very vital for the performance of a high-speed floating-point adder in today's state of art microprocessor design. Unfortunately, in predicting "shift amount"by a conventional LZA design, the result could be off by one position. This paper presents a novel parallel error detection algorithm for a general-case LZA. The proposed approach enables parallel execution of conventional LZA and its error detection, so that the error-indication signal can be generated earlier in the stage of normalization, thus reducing the critical path and improving overall performance. The circuit implementation of this algorithm also shows its advantages of area and power compared with other previous work.

  7. The gains and losses of collusion: An empirical research on the market behaviors of China’s power enterprises

    Directory of Open Access Journals (Sweden)

    Ruize Gao

    2015-05-01

    Full Text Available Purpose: Collusion is a common behavior of oligarch enterprises aiming to get an advantage in market competition. The purpose of the thesis is to use the empirical research methods to explore positive or negative effects that the electricity generation manufacturers’ collusion has caused at the macro level of Market Economy and the micro level of enterprises’ behaviors. Design/methodology/approach: The designed research model in the thesis is an extension of Porter’s model (Porter, 1984. It applies a more advanced measurement method, FIML. In the example of price bidding project that started by electricity generation enterprises of China’s power industry, the thesis analyzes the relevant price data of subordinate power plants of China’s five power generation groups in pilots of price bidding Policy. Findings: It is found in the thesis that power generation enterprises are facing collusion issues in the market. To be exact, it is such a situation in which non-cooperative competition and collusion alternate. Under the competition, market is relatively steady, thus forming a lower network price. It is helpful to the development of the whole industry. However, once Cartel is formed, the price will rise and clash with power enterprises and transmission-distribution companies concerning the interests conflicts. At the same time, a higher power price will form in the market, making consumers suffer losses. All of these are bad for industry development. Not only the collusion of power enterprises affects power price but also the market power that caused by long-time Cartel will reduce the market entrant in electricity generation. Market resources are centralized in the hands of Cartel, causing a low effective competition in the market, which has passive effects on users. Implications: The empirical research also indicates that collusion undoubtedly benefits the power enterprises that involved. As a cooperation pattern, collusion can lead to

  8. A follow-up power analysis of the statistical tests used in the Journal of Research in Science Teaching

    Science.gov (United States)

    Woolley, Thomas W.; Dawson, George O.

    It has been two decades since the first power analysis of a psychological journal and 10 years since the Journal of Research in Science Teaching made its contribution to this debate. One purpose of this article is to investigate what power-related changes, if any, have occurred in science education research over the past decade as a result of the earlier survey. In addition, previous recommendations are expanded and expounded upon within the context of more recent work in this area. The absence of any consistent mode of presenting statistical results, as well as little change with regard to power-related issues are reported. Guidelines for reporting the minimal amount of information demanded for clear and independent evaluation of research results by readers are also proposed.

  9. Safety Re-evaluation of Kyoto University Research Reactor by reflecting the Accident of Fukushima Daiichi Nuclear Power Plant

    Energy Technology Data Exchange (ETDEWEB)

    Nakajima, K.; Yamamoto, T. [Kyoto Univ., Kyoto (Japan)

    2013-07-01

    Kyoto University Research Reactor (KUR) is a light-water moderated tank-type reactor operated at rated thermal power of 5MW. After the accident of Fukushima Daiichi nuclear power plant, we have settled a 40-ton water tank near the reactor room, and prepared a mobile fire pump and a mobile power generator as additional safety measures for beyond design basis accidents (BDBAs). We also have conducted the safety re-evaluation of KUR, and confirmed that the integrity of KUR fuels could be kept against the BDBA with the use of the additional safety measures when the several restrictions were imposed on the reactor operation.

  10. Absolute desingularization in characteristic zero

    OpenAIRE

    Temkin, Michael

    2010-01-01

    We present a survey on the recent progress with desingularization of quasi-excellent schemes of characteristic zero. Due to expository goals of the paper we concentrate on giving examples and outlining main ideas, and we refer to other sources for detailed proofs and technical details. This survey will be published in the proceedings of the conference "Motivic integration and its interactions with model theory and non-archimedean geometry" (ICMS, May 2008).

  11. Fat and Thin Fisher Zeroes

    CERN Document Server

    Janke, W; Stathakopoulos, M

    2002-01-01

    We show that it is possible to determine the locus of Fisher zeroes in the thermodynamic limit for the Ising model on planar (``fat'') phi4 random graphs and their dual quadrangulations by matching up the real part of the high- and low-temperature branches of the expression for the free energy. Similar methods work for the mean-field model on generic, ``thin'' graphs. Series expansions are very easy to obtain for such random graph Ising models.

  12. Electric Power quality Analysis in research reactor: Impacts on nuclear safety assessment and electrical distribution reliability

    Energy Technology Data Exchange (ETDEWEB)

    Touati, Said; Chennai, Salim; Souli, Aissa [Nuclear Research Centre of Birine, Ain Oussera, Djelfa Province (Algeria)

    2015-07-01

    The increased requirements on supervision, control, and performance in modern power systems make power quality monitoring a common practise for utilities. Large databases are created and automatic processing of the data is required for fast and effective use of the available information. Aim of the work presented in this paper is the development of tools for analysis of monitoring power quality data and in particular measurements of voltage and currents in various level of electrical power distribution. The study is extended to evaluate the reliability of the electrical system in nuclear plant. Power Quality is a measure of how well a system supports reliable operation of its loads. A power disturbance or event can involve voltage, current, or frequency. Power disturbances can originate in consumer power systems, consumer loads, or the utility. The effect of power quality problems is the loss power supply leading to severe damage to equipments. So, we try to track and improve system reliability. The assessment can be focused on the study of impact of short circuits on the system, harmonics distortion, power factor improvement and effects of transient disturbances on the Electrical System during motor starting and power system fault conditions. We focus also on the review of the Electrical System design against the Nuclear Directorate Safety Assessment principles, including those extended during the last Fukushima nuclear accident. The simplified configuration of the required system can be extended from this simple scheme. To achieve these studies, we have used a demo ETAP power station software for several simulations. (authors)

  13. Net-Zero Energy Technical Shelter

    DEFF Research Database (Denmark)

    Zhang, Chen; Heiselberg, Per; Jensen, Rasmus Lund

    2014-01-01

    Technical shelters are the basic structures for storing electronic and technical equipment, and commonly used for telecommunication base station, windmill, gas station, etc. Due to their high internal heat load density and special operation schedule, they consume more energy than normal residenti...... environment and energy performance of the technical shelter. Finally, a wind-solar hybrid energy system is designed as an alternative power solution for technical shelter, in order to achieve a net-zero energy target....... or commercial buildings. On the other hand, it is a big challenge to power the technical shelter in remote area where the grids are either not available or the expansion of grid is expensive. In order to minimize the energy consumption and obtain a reliable and cost-efficient power solution for technical......Technical shelters are the basic structures for storing electronic and technical equipment, and commonly used for telecommunication base station, windmill, gas station, etc. Due to their high internal heat load density and special operation schedule, they consume more energy than normal residential...

  14. Eastern Han Tombs at Ma'anling in Guigang City, Guangxi%广西贵港市马鞍岭东汉墓

    Institute of Scientific and Technical Information of China (English)

    广西壮族自治区文物工作队

    2002-01-01

    In December 1996-January 1997, three Eastern Han tombs at Ma'anling in Guigang City were excavated by the Guangxi Zhuang Autonomous Region Archaeological Team. Tomb M1 is a wooden-chambered rectangular earth shaft, M2 has a similar pit but no chamber, M3 is paved with bricks on the bottom, and each of them has a slanting tomb-passage. Among the funeral objects pottery vessels come first in number, bronzes next, and then some irons, silver articles and other artifacts. The pottery belongs mainly to the ding tripod, jar, pot, vase, gui food container, lian toilet box, bowl, hill incense burner, lamp, and house, well, granary and kitchen range molds; and the bronzes, to the bowl, dish, mirror and belt hook.

  15. Neutronic, steady-state, and transient analyses for the Kazakhstan VVR-K reactor with LEU fuel: ANL independent verification results

    Energy Technology Data Exchange (ETDEWEB)

    Hanan, Nelson A. [Argonne National Lab. (ANL), Argonne, IL (United States); Garner, Patrick L. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2015-08-01

    Calculations have been performed for steady state and postulated transients in the VVR-K reactor at the Institute of Nuclear Physics (INP), Kazakhstan. (The reactor designation in Cyrillic is BBP-K; transliterating characters to English gives VVR-K but translating words gives WWR-K.) These calculations have been performed at the request of staff of the INP who are performing similar calculations. The selection of the transients considered started during working meetings and email correspondence between Argonne National Laboratory (ANL) and INP staff. In the end the transient were defined by the INP staff. Calculations were performed for the fresh low-enriched uranium (LEU) core and for four subsequent cores as beryllium is added to maintain critically during the first 15 cycles. These calculations have been performed independently from those being performed by INP and serve as one step in the verification process.

  16. ANL的2Q-LEBT装置的进展报告%Status of the 2Q-LEBT Facility at ANL

    Institute of Scientific and Technical Information of China (English)

    R.H.Scott; V.N.Asseev; T.V.Kulevoy; P.N.0stroumov; E.A.Poklonskaya; M.Sengupta; N.E.Vinogradov

    2007-01-01

    The concept for a 2 charge state injector for a "RIA type" accelerator has been presented.Progress toward an operational prototype 2Q-LEBT system at Argonne National Laboratory(ANL)is under way.The existing BIE 100 all permanent magnet ECR has been placed on a high voltage platform capable of a combined>100kV with q/m separation at ground level.Remote control of the devices on the platform has been implemented.Other components of the facility are currently being tested.The components of an achromatic bending system are currently being procured.This paper will present recent work at the facility as well as preliminary development of solid materials using the BIE 100.

  17. A Novel Method of Zero Offset Reduction in Hall Effect Sensors with Applications to Magnetic Field Measurement

    Science.gov (United States)

    Liu, Cheng; Liu, Ji-Gou; Zhang, Quan

    2015-02-01

    The paper presents a novel method to reduce the zero offset in Hall-Effect based magnetic measurement with single power supply. This method consists of a coarse zero compensation and a fine zero adjustment afterwards. By using the proposed method the zero output offset of Hall Effect sensors under using single power supply can be controlled within 0.2%. This method can be applied to all Hall Effect sensors with analog output and other similar sensors, which are powered with a single voltage or current source.

  18. Research of Reliable Power Supply Schemes for OOO Gazprom Production Yamburg Gas Field

    Directory of Open Access Journals (Sweden)

    Askarov Alisher

    2015-01-01

    Full Text Available In article the analysis of substation electric part for the enterprises an oil and gas complex power supply is carried out: structure and switchgear schemes, uninterrupted reserve sources structure. Recommendations for power supply reliability are made.

  19. Study of seasonal snow cover influencing the ground thermal regime on western flank of Da Xing'anling Mountains, northeastern China

    Institute of Scientific and Technical Information of China (English)

    XiaoLi Chang; HuiJun Jin; YanLin Zhang; HaiBin Sun

    2015-01-01

    Although many studies relevant to snow cover and permafrost have focused on alpine, arctic, and subarctic areas, there is still a lack of understanding of the influences of seasonal snow cover on the thermal regime of the soils in permafrost regions in the mid-latitudes and boreal regions, such as that on the western flank of the Da Xing'anling (Hinggan) Mountains, northeastern China. This paper gives a detailed analysis on meteorological data series from 2001 to 2010 provided by the Gen'he Weather Station, which is located in a talik of discontinuous permafrost zone and with sparse meadow on the observation field. It is inferred that snow cover is important for the ground thermal regime in the middle Da Xing'anling Mountains. Snow cover of 10-cm in thickness and five to six months in duration (generally November to next March) can reduce the heat loss from the ground to the atmosphere by 28%, and by 71% if the snow depth increases to 36 cm. Moreover, the occurrence of snow cover resulted in mean annual ground surface temperatures 4.7–8.2°C higher than the mean annual air temperatures recorded at the Gen'he Weather Station. The beginning date for stable snow cover establishment (SE date) and the initial snow depth (SDi) also had a great influences on the ground freezing process. Heavy snowfall before ground surface freeze-up could postpone and retard the freezing process in Gen'he. As a result, the duration of ground freezing was shortened by at least 20 days and the maximum depth of frost penetration was as much as 90 cm shallower.

  20. Statistical Power of Psychological Research: What Have We Gained in 20 Years?

    Science.gov (United States)

    Rossi, Joseph S.

    1990-01-01

    Calculated power for 6,155 statistical tests in 221 journal articles published in 1982 volumes of "Journal of Abnormal Psychology,""Journal of Consulting and Clinical Psychology," and "Journal of Personality and Social Psychology." Power to detect small, medium, and large effects was .17, .57, and .83, respectively. Concluded that power of…

  1. Commodity production in Brazil: Combining zero deforestation and zero illegality

    Directory of Open Access Journals (Sweden)

    Andrea A. Azevedo

    2015-12-01

    Full Text Available Abstract This article documents the degree of noncompliance of soy producers in the Amazon portion of Mato Grosso with Brazil’s Forest Code and addresses the importance of market demands in shifting agricultural production and land occupation towards zero deforestation. By using a sample composed of the boundaries of 9,113 properties (72.5% of soy in the region we assessed: a compliance with Forest Code legal reserve requirements (a percentage of the property must have its original vegetation kept undisturbed; and compared it to b compliance with the zero deforestation criterion of the soy moratorium. We found that 82% of the sampled properties have not deforested since 2008, thus complying with the soy moratorium. However, approximately 65% out of these 82% are noncompliant with Forest Code legal reserve requirements. This situation is even worse in the Cerrado portion of Mato Grosso. Even though the soy moratorium criterion is only applicable to the Amazon biome, the Forest Code is applicable nationwide. Despite legal reserve requirements being much lower (35% of the property in the Cerrado, as opposed to 80% in the Amazon, almost 70% of sampled properties were noncompliant with the Forest Code. From this analysis we concluded that while there was a role for consumer-driven market demand for zero deforestation soy production, there is still a need (and opportunity to implement purchasing and financing criteria to promote compliance with Forest Code requirements in regards to legal reserve deficits. We believe that if this succeeds, it will drive a process of restoration and compensation of Forest Code deficits, strengthening public policy as well as reducing economic distortions between those who have and have not complied with Forest Code requirements.

  2. Practical superconductor development for electrical power applications - Argonne National Laboratory - quarterly report for the period ending June 30, 2001.

    Energy Technology Data Exchange (ETDEWEB)

    Dorris, S. E.

    2001-08-21

    This is a multiyear experimental research program focused on improving relevant material properties of high-T{sub c} superconductors (HTSs) and on development of fabrication methods that can be transferred to industry for production of commercial conductors. The development of teaming relationships through agreements with industrial partners is a key element of the Argonne (ANL) program.

  3. EXPERIMENTAL RESEARCHES OF ELASTOMERIC MATERIALS TO STABILIZE THE OSCILLATION OF POWER GRID STRUCTURES

    Directory of Open Access Journals (Sweden)

    Iurii Priadko

    2015-12-01

    Full Text Available This paper proposes a new type of insulator, has both insulating and damping properties to improve the operational reliability of overhead power lines' structures (OHPL. In order to assess an effectiveness of the new insulator's design have made laboratory tests of a insulator model with different types of elastomer seals, differed of the rubber marks and the type of reinforcement. An experiment consist of two stages: at the first stage an object of study has been exposed to cyclical vibration, at the second – the impact of an impulsively load. Results of the research showed, that the most effective are the elastomeric gasket with a minimum rigidity characteristics without reinforcement. Using insulators with such dampers allows to reduce the first maximum impulse to a support by an average of 20% and reduce the frequency and amplitude characteristics of the system. Based on this was developed a new type of elastomer reinforcing with steel sheet elements in the form of a truncated cone.

  4. You talkin' to me? Interactive playback is a powerful yet underused tool in animal communication research.

    Science.gov (United States)

    King, Stephanie L

    2015-07-01

    Over the years, playback experiments have helped further our understanding of the wonderful world of animal communication. They have provided fundamental insights into animal behaviour and the function of communicative signals in numerous taxa. As important as these experiments are, however, there is strong evidence to suggest that the information conveyed in a signal may only have value when presented interactively. By their very nature, signalling exchanges are interactive and therefore, an interactive playback design is a powerful tool for examining the function of such exchanges. While researchers working on frog and songbird vocal interactions have long championed interactive playback, it remains surprisingly underused across other taxa. The interactive playback approach is not limited to studies of acoustic signalling, but can be applied to other sensory modalities, including visual, chemical and electrical communication. Here, I discuss interactive playback as a potent yet underused technique in the field of animal behaviour. I present a concise review of studies that have used interactive playback thus far, describe how it can be applied, and discuss its limitations and challenges. My hope is that this review will result in more scientists applying this innovative technique to their own study subjects, as a means of furthering our understanding of the function of signalling interactions in animal communication systems.

  5. Zero G Mass Measurement Device (ZGMMD) Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Zero G Mass Measurement Device (ZGMMD) will provide the ability to quantify the mass of objects up to 2,000 grams, including live animal specimens in a zero G...

  6. 用于风电机组系统的零动态理论PSS与STATCOM协调设计%Coordinated design of STATCOM and PSS controllers for power system with wind generation using zero dynamics method

    Institute of Scientific and Technical Information of China (English)

    时光; 王海云; 唐新安; 齐文雷

    2015-01-01

    励磁系统和FACTS装置的不协调设计会导致电网的鲁棒性变差.基于多输入多输出系统的励磁控制装置和STATCOM(同步无功补偿器)数学模型,利用零动态设计原理对系统PSS参数与STATCOM进行协调设计,分别在PSS与STATCOM协调和不协调两种情况下,应用DIgSILENT/PowerFactory软件对系统进行仿真,根据仿真结果得出,零动态设计原理可以显著提升含风电多机系统的动态稳定性且具有优良的品质.

  7. Maximum privacy without coherence, zero-error

    Science.gov (United States)

    Leung, Debbie; Yu, Nengkun

    2016-09-01

    We study the possible difference between the quantum and the private capacities of a quantum channel in the zero-error setting. For a family of channels introduced by Leung et al. [Phys. Rev. Lett. 113, 030512 (2014)], we demonstrate an extreme difference: the zero-error quantum capacity is zero, whereas the zero-error private capacity is maximum given the quantum output dimension.

  8. Zero Point Energy of Renormalized Wilson Loops

    OpenAIRE

    Hidaka, Yoshimasa; Pisarski, Robert D.

    2009-01-01

    The quark antiquark potential, and its associated zero point energy, can be extracted from lattice measurements of the Wilson loop. We discuss a unique prescription to renormalize the Wilson loop, for which the perturbative contribution to the zero point energy vanishes identically. A zero point energy can arise nonperturbatively, which we illustrate by considering effective string models. The nonperturbative contribution to the zero point energy vanishes in the Nambu model, but is nonzero wh...

  9. Splitting of acoustic energy by zero index metamaterials

    Energy Technology Data Exchange (ETDEWEB)

    Yan, Xinxin [School of Science, Hubei University of Technology, Wuhan 430068 (China); Department of Orthopedics, Tongji Medical College, Huazhong University of Science and Technology, Wuhan 430022 (China); Wei, Wei [Hubei Cancer Hospital, Wuhan 430079 (China); Hu, Ni [School of Science, Hubei University of Technology, Wuhan 430068 (China); Hubei Collaborative Innovation Center for High-efficiency Utilization of Solar Energy, Hubei University of Technology, Wuhan 430068 (China); Liu, Fengming, E-mail: fmliu@mail.hbut.edu.cn [School of Science, Hubei University of Technology, Wuhan 430068 (China); Hubei Collaborative Innovation Center for High-efficiency Utilization of Solar Energy, Hubei University of Technology, Wuhan 430068 (China)

    2015-10-02

    An acoustic power splitter is proposed by utilizing a zero index metamaterials (ZIM) junction. Two types of ZIM, single zero index metamaterials (SZIM) and double zero index metamaterials (DZIM), are considered. The acoustic wave transmission through the multiple leads junction is investigated theoretically and numerically. We show that perfect transmission can be achieved for the junction made of DZIM by tuning the widths of the output leads with respect to the input lead. It is also shown that the same effect is obtained for the junction made of SZIM by reducing the area of the junction or introducing a proper defect into the junction. A two-dimensional (2D) acoustic crystal (AC) with effective zero index is suggested to provide a practical realization for the splitting system. - Highlights: • An acoustic splitter is proposed by using a zero index metamaterials junction. • Perfect transmission can be achieved for the acoustic splitter. • The configuration of the acoustic splitter can be chosen at will.

  10. Transient and Steady-state Tests of the Space Power Research Engine with Resistive and Motor Loads

    Science.gov (United States)

    Rauch, Jeffrey S.; Kankam, M. David

    1995-01-01

    The NASA Lewis Research Center (LeRC) has been testing free-piston Stirling engine/linear alternators (FPSE/LA) to develop advanced power convertors for space-based electrical power generation. Tests reported herein were performed to evaluate the interaction and transient behavior of FPSE/LA-based power systems with typical user loads. Both resistive and small induction motor loads were tested with the space power research engine (SPRE) power system. Tests showed that the control system could maintain constant long term voltage and stable periodic operation over a large range of engine operating parameters and loads. Modest resistive load changes were shown to cause relatively large voltage and, therefore, piston and displacer amplitude excursions. Starting a typical small induction motor was shown to cause large and, in some cases, deleterious voltage transients. The tests identified the need for more effective controls, if FPSE/LAs are to be used for stand-alone power systems. The tests also generated a large body of transient dynamic data useful for analysis code validation.

  11. The Status of Research Regarding Magnetic Mirrors as a Fusion Neutron Source or Power Plant

    Energy Technology Data Exchange (ETDEWEB)

    Simonen, T

    2008-12-23

    Experimental results, theory and innovative ideas now point with increased confidence to the possibility of a Gas Dynamic Trap (GDT) neutron source which would be on the path to an attractively simple Axisymmetric Tandem Mirror (ATM) power plant. Although magnetic mirror research was terminated in the US 20 years ago, experiments continued in Japan (Gamma 10) and Russia (GDT), with a very small US effort. This research has now yielded data, increased understanding, and generated ideas resulting in the new concepts described here. Early mirror research was carried out with circular axisymmetric magnets. These plasmas were MHD unstable due to the unfavorable magnetic curvature near the mid-plane. Then the minimum-B concept emerged in which the field line curvature was everywhere favorable and the plasma was situated in a MHD stable magnetic well (70% average beta in 2XII-B). The Ioffe-bar or baseball-coil became the standard for over 40 years. In the 1980's, driven by success with minimum-B stabilization and the control of ion cyclotron instabilities in PR6 and 2XII-B, mirrors were viewed as a potentially attractive concept with near-term advantages as a lower Q neutron source for applications such as a hybrid fission fuel factory or toxic waste burner. However there are down sides to the minimum-B geometry: coil construction is complex; restraining magnetic forces limit field strength and mirror ratios. Furthermore, the magnetic field lines have geodesic curvature which introduces resonant and neoclassical radial transport as observed in early tandem mirror experiments. So what now leads us to think that simple axisymmetric mirror plasmas can be stable? The Russian GDT experiment achieves on-axis 60% beta by peaking of the kinetic plasma pressure near the mirror throat (where the curvature is favorable) to counter-balance the average unfavorable mid-plane curvature. Then a modest augmentation of plasma pressure in the expander results in stability. The GDT

  12. Light Water Reactor Sustainability Program Power Uprate Research and Development Strategy

    Energy Technology Data Exchange (ETDEWEB)

    Hongbin Zhang

    2011-09-01

    The economic incentives for low-cost electricity generation will continue to drive more plant owners to identify safe and reliable methods to increase the electrical power output of the current nuclear power plant fleet. A power uprate enables a nuclear power plant to increase its electrical output with low cost. However, power uprates brought new challenges to plant owners and operators. These include equipment damage or degraded performance, and unanticipated responses to plant conditions, etc. These problems have arisen mainly from using dated design and safety analysis tools and insufficient understanding of the full implications of the proposed power uprate or from insufficient attention to detail during the design and implementation phase. It is essential to demonstrate that all required safety margins have been properly retained and the existing safety level has been maintained or even increased, with consideration of all the conditions and parameters that have an influence on plant safety. The impact of the power uprate on plant life management for long term operation is also an important issue. Significant capital investments are required to extend the lifetime of an aging nuclear power plant. Power uprates can help the plant owner to recover the investment costs. However, plant aging issues may be aggravated by the power uprate due to plant conditions. More rigorous analyses, inspections and monitoring systems are required.

  13. Zeros of entire functions of finite order

    Directory of Open Access Journals (Sweden)

    Supper Raphaële

    2002-01-01

    Full Text Available Given , , let be the set of all entire functions , with , for which there exists some constant such that . It is shown that the zero set of a function of satisfies and that the union of the zero sets of two functions of is not necessarily the zero set of a function of . Some uniqueness results of Carlson's type are also obtained.

  14. Zero Tolerance in Tennessee Schools: An Update.

    Science.gov (United States)

    Potts, Kim; Njie, Bintou; Detch, Ethel R.; Walton, Jason

    As required by Tennessee law, this report examines the state's zero-tolerance disciplinary data collected by the Tennessee Department of Education for school years 1999-00, 2000-01, and 2001-02. The first section displays statewide zero-tolerance statistics. The second section focuses on the zero-tolerance statistics of Tennessee's five major…

  15. AN APPROACH TO ZERO CATEGORIES IN SYNTAX

    Directory of Open Access Journals (Sweden)

    Olga Vladimirovna Tikhanova

    2015-01-01

    Full Text Available The paper examined one of the least explored issues of the Russian philology, namely a syntactic zero. One should accurately differentiate the syntactic zero from other positions being not substituted in the sentence, such as ellipse, incompleteness, etc. Actually, one could hardly find the papers having considered this issue, with proper description and comprehensive differentiation for syntactic zero’ instances. Experts carried multiple debates on what one should recognize for a zero, and nobody arranged zero instances into classification. The authors made a review of the papers of academic significance the linguists have produced, and specified zero categories for the Russian language, and have sorted out the main features typical of the syntactic zero. The authors assumed that the experts could sort out much more null syntactic categories, for example, in considering the null subject in the so-called single-constituent clauses (indefinite personal or generalized personal clauses, or impersonal ones. The authors tried, in order to escape overburdening of the presentation, to start with looking into the most fundamental and universally recognized zeros, in their opinion, namely a zero form of the copula and a zero of any verb of existence. The main principle of differentiating a syntactic zero means it being isomorphic to zero categories at other levels of language, because at any level of language the concept of zero is derived by tradition upon the set of elements drawn up in compliance with the principle of oppositions (i.e. paradigm.

  16. Uniqueness and Zeros of -Shift Difference Polynomials

    Indian Academy of Sciences (India)

    Kai Liu; Xin-Ling Liu; Ting-Bin Cao

    2011-08-01

    In this paper, we consider the zero distributions of -shift difference polynomials of meromorphic functions with zero order, and obtain two theorems that extend the classical Hayman results on the zeros of differential polynomials to -shift difference polynomials. We also investigate the uniqueness problem of -shift difference polynomials that share a common value.

  17. Research on"Zero Complaint" Management of Reader Service in University Library%高校图书馆读者服务“零投诉”管理研究

    Institute of Scientific and Technical Information of China (English)

    范忆慧

    2012-01-01

    通过对读者投诉问题的分析,提出高校图书馆实施读者服务"零投诉"管理的措施,以实现图书馆社会效益最大化。%With analysing the problems of readers' appeal, this paper puts forward "zero complaint"management measures of university library readers services to realize the aim of the library social benefit maximizalion.

  18. Research and development for decontamination system of spent resin in Hanbit Nuclear Power Plant

    Energy Technology Data Exchange (ETDEWEB)

    Sung, Gi Hong [Dept. of Nuclear Engineering, Chosun University, Gwangju (Korea, Republic of)

    2015-12-15

    When reactor coolant leaks occur due to cracks of a steam generator tube, radioactive materials contained in the primary cooling water in nuclear power plant are forced out toward the secondary systems. At this time the secondary water purification resin in the ion exchange resin tower of the steam generator blowdown system is contaminated by the radioactivity of the leaked radioactive materials, so we pack this in special containers and store temporarily because we could not dispose it by ourselves. If steam generator tube leakage occurs, it produces contaminated spent resins annually about 5,000-7,000 liters. This may increase the amount of nuclear waste productions, a disposal working cost and a unit price of generating electricity in the plant. For this reasons, it is required to develop a decontamination process technique for reducing the radioactive level of these resins enough to handle by the self-disposal method. In this research, First, Investigated the structure and properties of the ion exchange resin used in a steam generator blowdown system. Second, Checked for a occurrence status of contaminated spent resin and a disposal technology. Third, identified the chemical characteristics of the waste radionuclides of the spent resin, and examined ionic bonding and separation mechanism of radioactive nuclear species and a spent resin. Finally, we carried out the decontamination experiment using chemicals, ultrasound, microbubbles, supercritical carbon dioxide to process these spent resin. In the case of the spent resin decontamination method using chemicals, the higher the concentration of the drug decontamination efficiency was higher. In the ultrasound method, foreign matter of the spent resin was removed and was found that the level of radioactivity is below of the MDA. In the microbubbles method, we found that the concentration of the radioactivity decreased after the experiment, so it can be used to the decontamination process of the spent resin. In

  19. Recovery Act: SeaMicro Volume Server Power Reduction Research Development

    Energy Technology Data Exchange (ETDEWEB)

    Gary Lauterbach

    2012-03-22

    Cloud data centers are projected to be the fastest growing segment of the server market through 2015, according to IDC. Increasingly people and businesses rely on the Cloud to deliver digital content quickly and efficiently. Recovery Act funding from the Department of Energy has helped SeaMicro's technologies enhance the total cost of operation, performance and energy efficiency in large data center and Cloud environments. SeaMicro's innovative supercomputer fabric connects thousands of processor cores, memory, storage and input/output traffic. The company's fabric supports multiple processor instruction sets. Current systems featuring SeaMicro technology typically use one quarter the power and take one sixth the space of traditional servers with the same compute performance, yet deliver up to 12 times the bandwidth per core. Mozilla and eHarmony are two customers successfully using SeaMicro's technology. Numerous non-public customers have been successfully using the SeaMicro product in test and production facilities. As a result of the Recovery Act funding from the U.S. Department of Energy, more than 50 direct jobs were created at SeaMicro. To date, they primarily have been high-value, engineering jobs. Hardware, software and manufacturing engineering positions have been created, as well as sales and sales engineering. The positions have allowed SeaMicro to significantly accelerate engineering development and accelerate commercialization. As a result, commercialization and delivery to market are months ahead of initial schedule. Additional jobs were indirectly created through the development of the SeaMicro product. Through many years of research and hard work prior to receipt of public funding, SeaMicro was awarded 2 patents for its work. SeaMicro's product led the way for industry leaders to reconsider the market for low power servers and create new product lines. With valuable support of the U.S. Department of Energy and through Sea

  20. Report on a Zero-Knowledge Protocal Tabletop Exercise.

    Energy Technology Data Exchange (ETDEWEB)

    Marleau, Peter [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Brubaker, Erik [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Deland, Sharon M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Hilton, Nathan R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); McDaniel, Michael [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Schroeppel, Richard C. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Seager, Kevin D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Stoddard, Mary Clare [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); MacArthur, Duncan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-06-01

    This report summarizes the discussion and conclusions reached during a table top exercise held at Sandia National Laboratories, Albuquerque on September 3, 2014 regarding a recently described approach for nuclear warhead verification based on the cryptographic concept of a zero-knowledge protocol (ZKP) presented in a recent paper authored by Glaser, Barak, and Goldston. A panel of Sandia National Laboratories researchers, whose expertise includes radiation instrumentation design and development, cryptography, and arms control verification implementation, jointly reviewed the paper and identified specific challenges to implementing the approach as well as some opportunities. It was noted that ZKP as used in cryptography is a useful model for the arms control verification problem, but the direct analogy to arms control breaks down quickly. The ZKP methodology for warhead verification fits within the general class of template-based verification techniques, where a reference measurement is used to confirm that a given object is like another object that has already been accepted as a warhead by some other means. This can be a powerful verification approach, but requires independent means to trust the authenticity of the reference warhead - a standard that may be difficult to achieve, which the ZKP authors do not directly address. Despite some technical challenges, the concept of last-minute selection of the pre-loads and equipment could be a valuable component of a verification regime.

  1. Zero-emission vehicle technology assessment. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Woods, T.

    1995-08-01

    This is the final report in the Zero-Emission Vehicle (ZEV) Technology Assessment, performed for NYSERDA by Booz-Allen & Hamilton Inc. Booz-Allen wrote the final report, and performed the following tasks as part of the assessment: assembled a database of key ZEV organizations, their products or services, and plans; described the current state of ZEV technologies; identified barriers to widespread ZEV deployment and projected future ZEV technical capabilities; and estimated the cost of ZEVs from 1998 to 2004. Data for the ZEV Technology Assessment were obtained from several sources, including the following: existing ZEV industry publications and Booz-Allen files; major automotive original equipment manufacturers; independent electric vehicle manufacturers; battery developers and manufacturers; infrastructure and component developers and manufacturers; the U.S. Department of Energy, the California Air Resources Board, and other concerned government agencies; trade associations such as the Electric Power Research Institute and the Electric Transportation Coalition; and public and private consortia. These sources were contacted by phone, mail, or in person. Some site visits of manufacturers also were conducted. Where possible, raw data were analyzed by Booz-Allen staff and/or verified by independent sources. Performance data from standardized test cycles were used as much as possible.

  2. Black Holes with Zero Mass

    CERN Document Server

    Nucamendi, U; Nucamendi, Ulises; Sudarsky, Daniel

    2000-01-01

    We consider the spacetimes corresponding to static Global Monopoles with interior boundaries corresponding to a Black Hole Horizon and analyze the behavior of the appropriate ADM mass as a function of the horizon radius r_H. We find that for small enough r_H, this mass is negative as in the case of the regular global monopoles, but that for large enough r_H the mass becomes positive encountering an intermediate value for which we have a Black Hole with zero ADM mass.

  3. Status report on the Small Secure Transportable Autonomous Reactor (SSTAR) /Lead-cooled Fast Reactor (LFR) and supporting research and development.

    Energy Technology Data Exchange (ETDEWEB)

    Sienicki, J. J.; Moisseytsev, A.; Yang, W. S.; Wade, D. C.; Nikiforova, A.; Hanania, P.; Ryu, H. J.; Kulesza, K. P.; Kim, S. J.; Halsey, W. G.; Smith, C. F.; Brown, N. W.; Greenspan, E.; de Caro, M.; Li, N.; Hosemann, P.; Zhang, J.; Yu, H.; Nuclear Engineering Division; LLNL; LANL; Massachusetts Inst. of Tech.; Ecole des Mines de Paris; Oregon State Univ.; Univ.of California at Berkley

    2008-06-23

    This report provides an update on development of a pre-conceptual design for the Small Secure Transportable Autonomous Reactor (SSTAR) Lead-Cooled Fast Reactor (LFR) plant concept and supporting research and development activities. SSTAR is a small, 20 MWe (45 MWt), natural circulation, fast reactor plant for international deployment concept incorporating proliferation resistance for deployment in non-fuel cycle states and developing nations, fissile self-sufficiency for efficient utilization of uranium resources, autonomous load following making it suitable for small or immature grid applications, and a high degree of passive safety further supporting deployment in developing nations. In FY 2006, improvements have been made at ANL to the pre-conceptual design of both the reactor system and the energy converter which incorporates a supercritical carbon dioxide Brayton cycle providing higher plant efficiency (44 %) and improved economic competitiveness. The supercritical CO2 Brayton cycle technology is also applicable to Sodium-Cooled Fast Reactors providing the same benefits. One key accomplishment has been the development of a control strategy for automatic control of the supercritical CO2 Brayton cycle in principle enabling autonomous load following over the full power range between nominal and essentially zero power. Under autonomous load following operation, the reactor core power adjusts itself to equal the heat removal from the reactor system to the power converter through the large reactivity feedback of the fast spectrum core without the need for motion of control rods, while the automatic control of the power converter matches the heat removal from the reactor to the grid load. The report includes early calculations for an international benchmarking problem for a LBE-cooled, nitride-fueled fast reactor core organized by the IAEA as part of a Coordinated Research Project on Small Reactors without Onsite Refueling; the calculations use the same neutronics

  4. The Transformative Power of Taking an Inquiry Stance on Practice: Practitioner Research as Narrative and Counter-Narrative

    Science.gov (United States)

    Ravitch, Sharon M.

    2014-01-01

    Within the ever-developing, intersecting, and overlapping contexts of globalization, top-down policy, mandates, and standardization of public and higher education, many conceptualize and position practitioner research as a powerful stance and a tool of social, communal, and educational transformation, a set of methodological processes that…

  5. Utilizing Critical Race Theory to Examine Race/Ethnicity, Racism, and Power in Student Development Theory and Research

    Science.gov (United States)

    Hernández, Ebelia

    2016-01-01

    Recognition of social forces (racism, privilege, power) to the extent that is required by critical race theory (CRT) results in a paradigm shift in the way that we theorize and research student development, specifically self-authorship. This paradigm shift moves the center of analysis from individual, to the individual in relation to her…

  6. RATU2. The Finnish research programme on the structural integrity of nuclear power plants. Interim report 1995 - April 1997

    Energy Technology Data Exchange (ETDEWEB)

    Solin, J.; Sarkimo, M.; Asikainen, M. [VTT Manufacturing Technology, Espoo (Finland). Materials and Structural Integrity] [eds.

    1997-06-01

    The projects within the Finnish public funded research programme on the structural integrity of nuclear power plants (RATU2) are briefly introduced and the scientific and technical results obtained during the first two years, 1995-April 1997, are summarised in this report. The RATU2 programme was started in 1995 and will be continued until 1998. In 1996 this programme represented 6 % of the nuclear energy R and D in Finland. The research programme is mainly publicly funded and supplies impartial expertise for the regulation of nuclear energy. It also plays an important role in the education of new experts, technology transfer and international exchange of scientific results. The programme is organised into five research projects on the following topics: Material degradation in the reactor environment, Reliability of nondestructive inspections of nuclear power plants, Structural analyses for nuclear power plant components, Maintenance strategies and dependability, and Fire safety. The ageing of the structures and components in the Finnish nuclear power plants is one of the main issues to be considered when safety and economic operation of the plants is evaluated. At the same time, ways are being sought to extend the lifetime of components. The first half of the RATU2 research programme has already brought significant scientific findings and useful applications for ensuring the reliability of NPP components. New technology has been transferred to domestic use through active participation to international co-operation. On the other hand, international acceptance of the results has provided valuable feedback and benchmarking. (orig.). 112 refs.

  7. Research on a New Control Scheme of Photovoltaic Grid Power Generation System

    Directory of Open Access Journals (Sweden)

    Dong-Hui Li

    2014-01-01

    Full Text Available A new type of photovoltaic grid power generation system control scheme to solve the problems of the conventional photovoltaic grid power generation systems is presented. To aim at the oscillation and misjudgment of traditional perturbation observation method, an improved perturbation observation method comparing to the next moment power is proposed, combining with BOOST step-up circuit to realize the maximum power tracking. To counter the harmonic pollution problem in photovoltaic grid power generation system, the deadbeat control scheme in fundamental wave synchronous frequency rotating coordinate system of power grid is presented. A parameter optimization scheme based on positive feedback of active frequency shift island detection to solve the problems like the nondetection zone due to the import of disturbance in traditional island detection method is proposed. Finally, the results in simulation environment by MATLAB/Simulink simulation and experiment environment verify the validity and superiority of the proposed scheme.

  8. Research on solar aided coal-fired power generation system and performance analysis

    Institute of Scientific and Technical Information of China (English)

    YANG YongPing; CUI YingHong; HOU HongJuan; GUO XiYan; YANG ZhiPing; WANG NinLing

    2008-01-01

    Integrationg rating solar power utilization systems with coal-fired power units, the solar aided coal-fired power generation (SACPG) shows a significant prospect for the large-scale utilization of solar energy and energy saving of thermal power units. The methods and mechanism of system integration were studied. The parabolic trough solar collectors were used to collect solar energy and the integration scheme of SACPG system was determined considering the matching of working fluid flows and energy flows. The thermodynamic characteristics of solar thermal power generation and their effects on the performance of thermal power units were studied, and based on this the integration and optimization model of system structure and parameters were built up. The integration rules and coupling mecha-nism of SACPG systems were summarized in accordance with simulation results. The economic analysis of this SACPG system showed that the solar LEC of a of SEGS, 0.14 S/kW. h.

  9. Research on Interactive Control of Electrolytic Aluminum Load and Wind Power Output

    Directory of Open Access Journals (Sweden)

    Ge Simin

    2016-01-01

    Full Text Available With the large-scale wind power generation connected to Gansu power grid, electrolytic aluminium load has reached a certain scale at the same time, the vast majority of electrolytic aluminium load directly connects to power grid using 330kV transmission line. According to the physical characteristics and historical data, the continuous adjustment characteristic of electrolytic aluminium load is analysed. Based on this characteristic, a mathematical model for the electrolytic aluminium load is established. Aiming at reducing power network loss and wind power consumption, an optimization model based on the load regulation characteristics of electrolytic aluminium is constructed, which is optimized by particle swarm optimization algorithm. Based on the case data of Gansu power grid, the optimal method based on the load regulation characteristics of electrolytic aluminium is analysed and its feasibility is verified.

  10. Research on DTX Technology and Power Consumption Performance of Mobile Communication Terminal

    Directory of Open Access Journals (Sweden)

    Xie Shui Zhen

    2016-01-01

    Full Text Available In order to reduce the power consumption of GSM and TD-SCDMA mobile communication system terminal, the paper starts with DTX (Discontinuous Transmission technology of GSM and TD-SCDMA systems, offers a detailed analysis of the DTX’s function in optimizing power consumption of GSM and TDSCDMA mobile communication system terminal and reducing system interference, and verifies DTX’s positive role in reducing the power consumption of the mobile terminal by experiment.

  11. Development of a large proton accelerator for innovative researches; development of high power RF source

    Energy Technology Data Exchange (ETDEWEB)

    Chung, K. H.; Lee, K. O.; Shin, H. M.; Chung, I. Y. [KAPRA, Seoul (Korea); Kim, D. I. [Inha University, Incheon (Korea); Noh, S. J. [Dankook University, Seoul (Korea); Ko, S. K. [Ulsan University, Ulsan (Korea); Lee, H. J. [Cheju National University, Cheju (Korea); Choi, W. H. [Korea Advanced Institute of Science and Technology, Taejeon (Korea)

    2002-05-01

    This study was performed with objective to design and develop the KOMAC proton accelerator RF system. For the development of the high power RF source for CCDTL(coupled cavity drift tube linac), the medium power RF system using the UHF klystron for broadcasting was integrated and with this RF system we obtained the basic design data, operation experience and code-validity test data. Based on the medium power RF system experimental data, the high power RF system for CCDTL was designed and its performed was analyzed. 16 refs., 64 figs., 27 tabs. (Author)

  12. Main Street Net-Zero Energy Buildings: The Zero Energy Method in Concept and Practice

    Energy Technology Data Exchange (ETDEWEB)

    Torcellini, P.; Pless, S.; Lobato, C.; Hootman, T.

    2010-01-01

    Until recently, large-scale, cost-effective net-zero energy buildings (NZEBs) were thought to lie decades in the future. However, ongoing work at the National Renewable Energy Laboratory (NREL) indicates that NZEB status is both achievable and repeatable today. This paper presents a definition framework for classifying NZEBs and a real-life example that demonstrates how a large-scale office building can cost-effectively achieve net-zero energy. The vision of NZEBs is compelling. In theory, these highly energy-efficient buildings will produce, during a typical year, enough renewable energy to offset the energy they consume from the grid. The NREL NZEB definition framework classifies NZEBs according to the criteria being used to judge net-zero status and the way renewable energy is supplied to achieve that status. We use the new U.S. Department of Energy/NREL 220,000-ft{sub 2} Research Support Facilities (RSF) building to illustrate why a clear picture of NZEB definitions is important and how the framework provides a methodology for creating a cost-effective NZEB. The RSF, scheduled to open in June 2010, includes contractual commitments to deliver a Leadership in Energy Efficiency and Design (LEED) Platinum Rating, an energy use intensity of 25 kBtu/ft{sub 2} (half that of a typical LEED Platinum office building), and net-zero energy status. We will discuss the analysis method and cost tradeoffs that were performed throughout the design and build phases to meet these commitments and maintain construction costs at $259/ft{sub 2}. We will discuss ways to achieve large-scale, replicable NZEB performance. Many passive and renewable energy strategies are utilized, including full daylighting, high-performance lighting, natural ventilation through operable windows, thermal mass, transpired solar collectors, radiant heating and cooling, and workstation configurations allow for maximum daylighting.

  13. Process simulation of a zero carbon emission power plant using CO2 as storage medium of renewable energy%以CO2作为可再生能源储存介质的零碳排放电厂过程模拟

    Institute of Scientific and Technical Information of China (English)

    盖少磊; 赵欢; 耿秀振; 辛斌斌

    2016-01-01

    Liquid fuel converted from CO2 and H2 O using renewable energy was utilized in zero carbon e-mission power plants,forming a closed cycle of“renewable energy( unstable energy supply)+CO2 +H2 Oliquid fuelselectricity( stable energy supply )+CO2 +H2 O”. Three main routes were considered for the conversion of CO2 and H2 O∶CO+H2 ,CO2 +H2 and CO2 +H2 O,in which CO and H2 come from the elec-trolysis of CO2 and H2 O,and electrolytic liquid product was methanol. To investigate these three conversion routes and the zero carbon emission power plant,Aspen Plus software was used to build proper models and conduct the thermodynamic analysis. The results show that when the conversion of CO2 is higher than 42%, the best route of methanol synthesis is the electrocatalytic conversion of CO2 and H2 O;while when CO2 con-version is lower than 42%,the optimal route is the hydrogenation of CO2 and CO. The simulation result also confirms that CO2 emission for the zero carbon emission power plant only decreases to 62. 5 kg/MW,which is just 7. 29% of that for the super critical coal-fired power plant.%利用可再生能源将CO2和H2 O转化为液体燃料可应用于零碳排放电厂,形成“可再生能源+CO2+H2 O液体燃料电力+CO2+H2 O”的循环利用模式。CO2和H2 O的转化主要有3条路径:CO+H2、CO2+H2以及CO2+H2 O,其中CO和H2来自CO2和H2 O的电解,液体产物为甲醇。为研究3条转化路径以及零碳排放电厂,利用Aspen Plus进行建模并做热力学分析。结果表明若CO2的转化率高于42%时,电催化转化CO2和H2 O为合成甲醇的最佳路径;若CO2的转化率低于42%时,则CO2和 CO的催化加氢同为最优路径。零碳排放电厂 CO2的排放降低到62.5 kg/MW,仅占超临界燃煤机组排放量的7.29%。

  14. Fundamental Research on Enhancing Operation Reliadility for Lange-Scale Interconnected Power Crids——An interview with Zhou Xiaoxin,chief scientist of"973 Program"

    Institute of Scientific and Technical Information of China (English)

    Zha Renbo; Zhou Wen

    2008-01-01

    @@ At the end of last year,the editors from Power and Electrical Engineers interviewedZhou Xiaoxin on "Fundamental Research on Enhancing Operation Reliability for Large-ScaleInterconnected Power Grids",a project of "973 Program".Mr.Zhou,the chief engineer ofChina Electric Power Research Institute (CEPRI) and an academician of Chinese A-cademy of Sciences,is the chief scientist in charge of this research project.

  15. Research and Development of High-Power and High-Energy Electrochemical Storage Devices

    Energy Technology Data Exchange (ETDEWEB)

    No, author

    2014-04-30

    The accomplishments and technology progressmade during the U.S. Department of Energy (DOE) Cooperative Agreement No. DE-FC26- 05NT42403 (duration: July 11, 2005 through April 30, 2014, funded for $125 million in cost- shared research) are summarized in this Final Technical Report for a total of thirty-seven (37) collaborative programs organized by the United States Advanced Battery Consortium, LLC (USABC). The USABC is a partnership, formed in 1991, between the three U.S. domestic automakers Chrysler, Ford, and General Motors, to sponsor development of advanced high-performance batteries for electric and hybrid electric vehicle applications. The USABC provides a unique opportunity for developers to leverage their resources in combination with those of the automotive industry and the Federal government. This type of pre-competitive cooperation minimizes duplication of effort and risk of failure, and maximizes the benefits to the public of the government funds. A major goal of this program is to promote advanced battery development that can lead to commercialization within the domestic, and as appropriate, the foreign battery industry. A further goal of this program is to maintain a consortium that engages the battery manufacturers with the automobile manufacturers and other key stakeholders, universities, the National Laboratories, and manufacturers and developers that supply critical materials and components to the battery industry. Typically, the USABC defines and establishes consensus goals, conducts pre-competitive, vehicle-related research and development (R&D) in advanced battery technology. The R&D carried out by the USABC is an integral part of the DOE’s effort to develop advanced transportation technologies that will significantly improve fuel economy, comply with projected emissions and safety regulations, and use domestically produced fuels. The USABC advanced battery development plan has the following three focus areas: 1. Existing technology

  16. End-user experiences in nearly zero-energy houses

    NARCIS (Netherlands)

    Mlecnik, E.; Schütze, T.; Jansen, S.J.T.; Vries, de G.; Visscher, H.; Hal, van J.D.M. (Anke)

    2012-01-01

    High end-user satisfaction levels are key for the acceptance of nearly zero-energy housing. Post-occupancy evaluation research on highly energy-efficient dwellings can lead to recommendations which will influence their performance in the expected future large volume market of such houses. This study

  17. Field Evaluation of a Near Zero Energy Home in Oklahoma

    Energy Technology Data Exchange (ETDEWEB)

    Hendron, R.; Hancock, E.; Barker, G.; Reeves, P.

    2008-08-01

    The authors evaluated a zero energy home built by Ideal Homes in Edmond, Oklahoma, that included an extensive package of energy-efficient technologies and a photovoltaic array for site electricity generation. The home was part of a Building America research project in partnership with the Building Science Consortium to exhibit high efficiency technologies while keeping costs within the reach of average home buyers.

  18. A Feminist Reflection on Ethnographic Research in China: Gender, Sex, and Power in Cross-Cultural Context

    Directory of Open Access Journals (Sweden)

    Arianne M. Gaetano

    2016-03-01

    Full Text Available As a feminist cultural anthropologist specializing in social transformations in contemporary China, my research and teaching necessarily involves exploring the construction of difference, the intersectionality of gender with other social positions, and how difference upholds or challenges power. In this essay, I employ biographical reflection to illustrate how my everyday experiences as a student, foreign English teacher, and scholarly researcher in China have refined my awareness of these important insights of feminist theory. As my attention to these processes increased, I became more mindful of the myriad ways women negotiate cultural configurations of gender and power in their everyday lives. Personal experiences also prompted me to reflect on how my identity and positionality impact the research process and outcomes. Thus experiential knowledge greatly enriched my study and understanding of the changing lives of women in China. I suggest how educators can impart these valuable lessons to students through experiential learning.

  19. Electric Power Lines : Questions and Answers on Research into Health Effects.

    Energy Technology Data Exchange (ETDEWEB)

    United States. Bonneville Power Administration.

    1993-11-01

    Most people know that electric power lines, like the wiring in our homes, can cause serious electric shocks if we`re not careful. Many people also want to know whether the electric and magnetic fields (EMF) produced by power lines and other electrical devices cause health effects. The purpose of this pamphlet is to answer some common questions that the Bonneville Power Administration (BPA) receives about the possible effects of power lines on health. (BPA is the Pacific Northwest`s Federal electric power marketing agency.) First, some basic electrical terms are defined, and electric and magnetic fields are described. Next, answers are given to several questions about recent scientific studies. We then describe how BPA is addressing public concerns raised by these studies. Some important information about electrical safety follows. The last section tells you how to obtain more detailed information about the health and safety issues summarized in this pamphlet.

  20. Electric Power Lines : Questions and Answers on Research into Health Effects.

    Energy Technology Data Exchange (ETDEWEB)

    United States. Bonneville Power Administration.

    1994-05-01

    Most people know that electric power lines, like the wiring in our homes, can cause serious electric shocks if we`re not careful. Many people also want to know whether the electric and magnetic fields (EMF) produced by power lines and other electrical devices cause health effects. The purpose of this booklet is to answer some common questions that the Bonneville Power Administration (BPA) receives about the possible effects of power lines on health. First, some basic electrical terms are defined, and electric and magnetic fields are debed. Next, answers are given to several questions about recent scientific studies. Some important information about electrical safety follows. We then describe how BPA is addressing public concerns about potential health effects of power lines. The last section tells you how to obtain more detailed information about the health and safety issues summarized in this booklet.

  1. Research on Hybrid Power System with Dual Stator-winding and Its Decoupled Control Strategy

    Institute of Scientific and Technical Information of China (English)

    WEI Shu-guang; MA Xiao-jun; KE Rong-shuo; LIU Qiu-li

    2012-01-01

    For the bi-power system adopted widely in future armored vehicles,a hybrid power generator with dual stator-winding was proposed.Its structure and working principle were analyzed first,and its main parameters were determined and verified according to the power requirements.The system's mathematical model was established,and a decoupled control method was put forward on the basis of the instantaneous reactive power theory.For the voltage building-up,a voltage control strategy was designed on the basis of mixed reactive power compensation to implement stabilized 28V and 270V outputs simultaneously.The simulation results show that the stabilization accuracy and disturbance rejection ability of the system are improved much more than other ordinary generators.

  2. Research on power grid loss prediction model based on Granger causality property of time series

    Energy Technology Data Exchange (ETDEWEB)

    Wang, J. [North China Electric Power Univ., Beijing (China); State Grid Corp., Beijing (China); Yan, W.P.; Yuan, J. [North China Electric Power Univ., Beijing (China); Xu, H.M.; Wang, X.L. [State Grid Information and Telecommunications Corp., Beijing (China)

    2009-03-11

    This paper described a method of predicting power transmission line losses using the Granger causality property of time series. The stable property of the time series was investigated using unit root tests. The Granger causality relationship between line losses and other variables was then determined. Granger-caused time series were then used to create the following 3 prediction models: (1) a model based on line loss binomials that used electricity sales to predict variables, (2) a model that considered both power sales and grid capacity, and (3) a model based on autoregressive distributed lag (ARDL) approaches that incorporated both power sales and the square of power sales as variables. A case study of data from China's electric power grid between 1980 and 2008 was used to evaluate model performance. Results of the study showed that the model error rates ranged between 2.7 and 3.9 percent. 6 refs., 3 tabs., 1 fig.

  3. Zero Tillage cotton systems and soil quality

    Science.gov (United States)

    Landers, J. N.; de Freitas, P. L.

    2012-04-01

    Monocropping in cotton production systems negates the benefits of zero tillage. With cotton in a 3-year rotation including other summer and cover crops, such as soybeans and intensive-rooting Brachiaria spp., research on sandy soils in Bahia improved soil fertility, structure and biological activity. Cotton is a deep tap-rooted crop, sensitive to physical and chemical impediments to root development; this has engendered a paradigm of heavy soil preparation operations to remove these. But, ZT can overcome such obstacles, allowing the cotton crop to benefit from cost reductions and a number of other benefits, especially erosion control.. Soil quality has three principal dimensions. Maximum yields only occur when soil fertility, structure and biological activity are in balance. Under Zero Tillage management of Brazilian soils, the processes of nutrient availability, nutrient cycling and efficiency result from increasing SOM and higher CEC. ZT system fertility is also strongly influenced by total annual aerial and root biomass generation; C:N ratios of the biomass, changes in aeration in residue breakdown processes (for roots, dependent on internal drainage), reduced fixation of Phosphorus fertilizers, the possibility of surface application of P and K, use of deep-rooted cover crops to re-cycle nutrients and deleterious effects of over-liming. Soil physical parameters undergo a transformation : greater water holding capacity, a small increase in bulk density (ameliorated by a reversal of soil aggregate breakdown inherent to conventional tillage by the binding action of root exudates and fungal hyphae), enhanced particle aggregate size protects SOM from oxidation; old root holes create semi-permanent macro-pores which facilitate rooting, aeration and rainfall infiltration.. Soil life of all types benefits from ZT management and contributes to soil fertility and structural improvements, plus enhancing certain biological controls of pathogenic organisms and allelopathic

  4. Overview of research in atmospheric icing of power network equipment at Universite du Quebec a Chicoutimi (UQAC)

    Energy Technology Data Exchange (ETDEWEB)

    Farzaneh, M. [Quebec Univ., Chicoutimi, PQ (Canada). Industrial Chair on Atmospheric Icing of Power Network Equipment

    2006-07-01

    This paper presented an outline of the research activities conducted by the Industrial Chair on Power Network Equipment (CIGELE). The mission and objectives of CIGELE were reviewed, as well as details of its research orientation and facilities, partner and collaborators. The scope of CIGELE research includes studies on mathematical modeling as well as physical and numerical simulation of a number of fundamental phenomena related to the processes of ice accretion and ice shedding from ground wires and phase conductors. The program also includes probabilistic studies of icing and aims to improve measurement methods for the various parameters associated with the icing of power lines. Objectives of the program are to train personnel, maintain an international leadership in the field of atmospheric icing, and establish collaborations with universities and research centres as well as partnerships with industry. The main research topics at CIGELE include the study of physical processes and laboratory simulations of icing precipitations; gathering and processing data from natural sites; modeling of power network equipment icing; modeling of the processes involved in ice shedding from ground wires and phase conductors; the study of electrical phenomena related to icing; the development of ice and snow accumulation prevention methods; and, the study of the dynamic behaviour of iced cables subjected to mechanical shocks. Six separate laboratories are located within the Icing Research Pavilion and include a wind tunnel, climate rooms, high voltage equipment and a plasma reactor. Research at CIGELE has resulted in the development of a new generation of 3D models used to predict the mass and shape of ice accretion on ground wires and phase conductors. New mathematical models for predicting natural ice shedding resulting from melting, sublimation and mechanical breaking have also been created. More than 500 publications have been published by students and researchers at CIGELE

  5. Application of Hybrid Real-Time Power System Simulator for Designing and Researching of Relay Protection and Automation

    Science.gov (United States)

    Borovikov, Yu S.; Sulaymanov, A. O.; Andreev, M. V.

    2015-10-01

    Development, research and operation of smart grids (SG) with active-adaptive networks (AAS) are actual tasks for today. Planned integration of high-speed FACTS devices greatly complicates complex dynamic properties of power systems. As a result the operating conditions of equipment of power systems are significantly changing. Such situation creates the new actual problem of development and research of relay protection and automation (RPA) which will be able to adequately operate in the SGs and adapt to its regimes. Effectiveness of solution of the problem depends on using tools - different simulators of electric power systems. Analysis of the most famous and widely exploited simulators led to the conclusion about the impossibility of using them for solution of the mentioned problem. In Tomsk Polytechnic University developed the prototype of hybrid multiprocessor software and hardware system - Hybrid Real-Time Power System Simulator (HRTSim). Because of its unique features this simulator can be used for solution of mentioned tasks. This article introduces the concept of development and research of relay protection and automation with usage of HRTSim.

  6. Modelling, design, and optimization of net-zero energy buildings

    CERN Document Server

    Athienitis, Andreas

    2015-01-01

    Building energy design is currently going through a period of major changes. One key factor of this is the adoption of net-zero energy as a long term goal for new buildings in most developed countries. To achieve this goal a lot of research is needed to accumulate knowledge and to utilize it in practical applications. In this book, accomplished international experts present advanced modeling techniques as well as in-depth case studies in order to aid designers in optimally using simulation tools for net-zero energy building design. The strategies and technologies discussed in this book are, ho

  7. Zero-determinant strategies in iterated multi-strategy games

    OpenAIRE

    Jin-Li Guo

    2014-01-01

    Self-serving, rational agents sometimes cooperate to their mutual benefit. The two-player iterated prisoner's dilemma game is a model for including the emergence of cooperation. It is generally believed that there is no simple ultimatum strategy which a player can control the return of the other participants. The recent discovery of the powerful class of zero-determinant strategies in the iterated prisoner's dilemma dramatically expands our understanding of the classic game by uncovering stra...

  8. Strong Purcell effect in anisotropic $\\varepsilon$-near-zero metamaterials

    CERN Document Server

    Chebykin, A V; Shalin, A S; Poddubny, A N; Belov, P A

    2014-01-01

    We theoretically demonstrate the strong Purcell effect in $\\varepsilon$-near-zero ultra-anisotropic uniaxial metamaterials with elliptic isofrequency surface. Contrary to the hyperbolic metamaterials, the effect does not rely on the diverging density of states and evanescent waves. As a result, both the radiative decay rate and the far-field emission power are enhanced. The effect can be realized in the periodic layered metal-dielectric nanostructures with complex unit cell containing two different metallic layers.

  9. Parahydrogen enhanced zero-field nuclear magnetic resonance

    OpenAIRE

    Theis, Thomas; Ganssle, Paul; Kervern, Gwendal; Knappe, Svenja; Kitching, John; Ledbetter, Micah; Budker, Dmitry; Pines, Alex

    2011-01-01

    Nuclear magnetic resonance (NMR), conventionally detected in multi-tesla magnetic fields, is a powerful analytical tool for the determination of molecular identity, structure, and function. With the advent of prepolarization methods and alternative detection schemes using atomic magnetometers or superconducting quantum interference devices (SQUIDs), NMR in very low- (~earth's field), and even zero-field, has recently attracted considerable attention. Despite the use of SQUIDs or atomic magnet...

  10. Multiple external hazards compound level 3 PSA methods research of nuclear power plant

    Science.gov (United States)

    Wang, Handing; Liang, Xiaoyu; Zhang, Xiaoming; Yang, Jianfeng; Liu, Weidong; Lei, Dina

    2017-01-01

    2011 Fukushima nuclear power plant severe accident was caused by both earthquake and tsunami, which results in large amount of radioactive nuclides release. That accident has caused the radioactive contamination on the surrounding environment. Although this accident probability is extremely small, once such an accident happens that is likely to release a lot of radioactive materials into the environment, and cause radiation contamination. Therefore, studying accidents consequences is important and essential to improve nuclear power plant design and management. Level 3 PSA methods of nuclear power plant can be used to analyze radiological consequences, and quantify risk to the public health effects around nuclear power plants. Based on multiple external hazards compound level 3 PSA methods studies of nuclear power plant, and the description of the multiple external hazards compound level 3 PSA technology roadmap and important technical elements, as well as taking a coastal nuclear power plant as the reference site, we analyzed the impact of off-site consequences of nuclear power plant severe accidents caused by multiple external hazards. At last we discussed the impact of off-site consequences probabilistic risk studies and its applications under multiple external hazards compound conditions, and explained feasibility and reasonableness of emergency plans implementation.

  11. 基于电子手轮的旋转编码器找零装置研制%Research on Device to Find Zero Position for Rotary Encoder Based on Electronic Handwheel

    Institute of Scientific and Technical Information of China (English)

    丁仕燕

    2013-01-01

    An adjustment device is designed in order to make the rotary encoder can be installed at zero position. The adjustment device is composed of a computer, a electronic handwheel, a step motor, a helical gear, a worm and a magnetic table block. The helical gear is installed on hollow shaft of rotary encoder, the worm is intalled in the magnetic table block. Based on output signals of the electronic handwheel, direction signals and pulses are sent to step motor driver by computer, the hollow shaft of the rotary encoder is driven finally. At the same time, output signals of the rotary encoder are read by the computer and used to judge whether the rotary encoder is at zero position. After rough localization and accurate localization, the rotary encoder can be installed at zero position efficiently and accurately.%为了使旋转编码器安装时在零位,设计了找零位装置,该装置包括:计算机、电子手轮、步进电机、蜗杆、斜齿轮和磁力表座组件.斜齿轮安装在旋转编码器空心轴上,蜗杆安装在磁力表座组件上.计算机根据电子手轮输出信号,向步进电机驱动器发出方向、脉冲信号,最终驱动编码器空心轴旋转.计算机读取旋转编码器输出信号以判断其是否在零位.经过粗定位、精定位两个步骤可快捷、准确地把旋转编码器安装在零位.

  12. Research and practice of implementing zero inventory on the drug warehouse in hospital%我院药库实施零库存的研究与实践

    Institute of Scientific and Technical Information of China (English)

    李要锋

    2013-01-01

    目的:在保证临床正常用药的前提下,探讨如何降低药库库存,增加药品和资金流转率,科学管理医院药品库房。方法利用HIS系统与药品ABC管理法,对我院药品库房实行零库存管理。结果通过实行药品零库存管理,我院药品的流转率得到明显提高,资金的周转由原来的32.6d降低为13.5d,周转率得到明显改善。结论建立适合院情的库存管理模式,应用零库存理念管理医院药库,对降低医院运营成本,提高工作效率具有重大意义。%Objective To explore reduction of inventory in the drug warehouse, increase of drug and cash flow ratio and scientific management of drug warehouse with the prerequisite of ensuring regular clinical drug use. Methods HIS system and ABC drug management were applied to implement zero-inventory management of the drug warehouse in our hospital. Results Zero inventory drug management significantly increased drug flow ratio, and improved cash turnover ratio with cash turnover decreasing from 32.6 days to 13.5 days. Conclusion Establishment of appropriate inventory management mode and application of zero-inventory theory in drug warehouse management are of great significance for reduction of operating cost and increase of work efficiency in hospital.

  13. Rethinking Race and Power in Design-Based Research: Reflections from the Field

    Science.gov (United States)

    Vakil, Sepehr; McKinney de Royston, Maxine; Suad Nasir, Na'ilah; Kirshner, Ben

    2016-01-01

    Participatory design-based research continues to expand and challenge the "researcher" and "researched" paradigm by incorporating teachers, administrators, community members, and youth throughout the research process. Yet, greater clarity is needed about the racial and political dimensions of these collaborative research…

  14. Does It Matter If Non-Powerful Significance Tests Are Used in Dissertation Research?

    Directory of Open Access Journals (Sweden)

    Heping Deng

    2005-09-01

    Full Text Available This study examines the statistical power levels presented in the dissertations completed in the field of educational leadership or educational administration. Eighty out of 221 reviewed dissertations were analyzed and overall statistical power levels were calculated for 2,629 significance tests. The statistical power levels demonstrated in the dissertations were satisfactory for detecting Cohen's large effect (d=0.80 and medium effect (d=0.50 but quite low for small effect (d=0.20. Therefore, the authors of analyzed dissertations had a very low probability of finding true significance when looking for Cohen's small effect.

  15. 旋转编码器安装至零位调整装置研制%Research on adjustment device for rotary encoder to be installed at zero position

    Institute of Scientific and Technical Information of China (English)

    丁仕燕; 干为民

    2012-01-01

    The adjustment device is designed in order that rotary encoder can be installed at zero position. The adjustment device is composed of a helical gear, a worm and magnetic table block. The helical gear is installed on hollow shaft of rotary encoder, the magnetic table block is fixed on automated equipment by means of magnetic suction, and the worm is intalled in axle sleeve, which is clamped in elastic hole chuck of the magnetic table block. The helical gear is drived by the worm, the hollow shaft of rotary encoder is driven by helical gear. Output signals of the rotary encoder is read by software and used to judge whether the rotary encoder is at zero position. The rotation of the worm is stop immediately if the rotary encoder is at zero position. The result of experiment shows that the rotary encoder can be installed at zero position efficiently and easily by means of the adjustment device.%为了使旋转编码器安装时在零位,设计了零位调整装置.该装置包括:斜齿轮、蜗杆和磁力表座组件.斜齿轮安装在旋转编码器的空心转轴上;磁力表座组件依靠磁铁吸力固定在自动化设备上,蜗杆安装在轴套中,该轴套被夹在磁力表座组件的弹性孔夹头中.蜗杆发生转动时驱动斜齿轮,进而驱动旋转编码器空心转轴,同时计算机软件读取旋转编码器输出信号以判断其是否到达零位,如在零位,则停止转动蜗杆.实验结果表明:使用该装置可方便、快捷地把旋转编码器安装在零位.

  16. Research on the influence mechanism of earth's magnetic field on zero bias of high precision FOG%地磁场对高精度光纤陀螺仪零偏的影响机理研究∗

    Institute of Scientific and Technical Information of China (English)

    谌尧周; 王夏霄; 高洋洋; 黄宛

    2016-01-01

    Combined with"four position"error problem in inertial navigation system calibration,it was analyzed that the influence mechanism of magnet sensitivity on zero bias stability of FOG in theory,we can obtain the cosine function model between gyro bias and the angle that magnetic field effect on the optical fiber ring;the Influence of magnet field on bias stability is linear,the influence of magnet field with arbitrary directions can be resolved into the sum of two orthotropic magnet fields.Finally,we tested two F120 high precision fiber optic gyroscopes at room temperature and static state,and got zero bias of gyro is 0.2o/h,0.3o/h in all direction range,and zero bias of gyro was decreased to 0.027o/h,0.038o/h with magnetic shielding,the magnetic shielding can decrease the influence on zero bias of high precision FOG from earth’s magnetic field effectively.%结合惯导系统标定时的“四位置”误差问题,从理论上分析了光纤陀螺的磁敏感性对其零偏的影响机理,得到地磁场对光纤环的影响角度θ0与光纤陀螺零偏误差的余弦函数模型;相位误差Δφ与磁场强度 H 呈线性关系;任一方向磁场对光纤陀螺的作用下都可以分解为正交两磁场的单独作用之和等结论。最后,对两支 F120型高精度光纤陀螺进行常温静态测试,测试得到在全方位范围内,陀螺的零偏极差分别为0.2o/h、0.28o/h,加磁屏蔽后,陀螺的零偏极差减小到为0.027o/h、0.038o/h,磁屏蔽能有效减小地磁场对高精度光纤陀螺零偏的影响。

  17. Catalogue of space objects and events as a powerful tool for scientific researches on space debris

    Science.gov (United States)

    Agapov, V.; Stepanyants, V.; Tuchin, A.; Khutorovsky, Z.

    modeling and space objects and events dynamical catalogue maintenance has wide functionality. Following tasks are developed, programmed, tested and working by now:- querying and analysis of statistical data on objects and events- analysis of orbital evolution for real objects based on real orbital data andmodeling of long-term evolution for given orbit- determination and analysis of close approaches between orbital objects- analysis of possibilities of specific objects observations by various sensors- a priory and a posteriori orbital data accuracy estimation taking intoaccount different types of sensors and kinds of measurements,measurements quality estimation- meas urement processing: identification with object in the catalogue,construction of initial estimation of orbital parameters, orbitaldetermination- high - efficient (by time and quality) orbital propagation- dynamical catalogue of objects in GEO region maintenance- presenting of orbital data in universal form permitting to use them withoutspecial propagation software- calculation of near-Earth objects distribution density and probability ofcollision- re-entry prediction for large objects Each one will be discussed in the presentation. For providing high - efficient work with the Catalogue powerful GUI is developed. It permits easily to query data and present results in form of tables, charts, graphics, show them with the map at the background. Projection of trajectory and error ellipsoid can be displayed on the sky or Earth map. Special interactive tools permits to control process of calculation. Many of developed tools and stored data can be used not just for space debris analysis but also for space missions analysis, studying atmosphere drag, developing object observation strategy etc. The next important step in the complex developing is providing access to it for wide range of outer users from various scientific and research organizations over the world using modern Internet technologies. Organizations of

  18. Landau levels and Riemann zeros.

    Science.gov (United States)

    Sierra, Germán; Townsend, Paul K

    2008-09-12

    The number N(E) of complex zeros of the Riemann zeta function with positive imaginary part less than E is the sum of a "smooth" function N[over ](E) and a "fluctuation." Berry and Keating have shown that the asymptotic expansion of N[over ](E) counts states of positive energy less than E in a "regularized" semiclassical model with classical Hamiltonian H=xp. For a different regularization, Connes has shown that it counts states "missing" from a continuum. Here we show how the "absorption spectrum" model of Connes emerges as the lowest Landau level limit of a specific quantum-mechanical model for a charged particle on a planar surface in an electric potential and uniform magnetic field. We suggest a role for the higher Landau levels in the fluctuation part of N(E).

  19. Tribology Experiment in Zero Gravity

    Science.gov (United States)

    Pan, C. H. T.; Gause, R. L.; Whitaker, A. F.; Finckenor, M. M.

    2015-01-01

    A tribology experiment in zero gravity was performed during the orbital flight of Spacelab 1 to study the motion of liquid lubricants over solid surfaces. The absence of a significant gravitational force facilitates observation of such motions as controlled by interfacial and capillary forces. Two experimental configurations were used. One deals with the liquid on one solid surface, and the other with the liquid between a pair of closed spaced surfaces. Time sequence photographs of fluid motion on a solid surface yielded spreading rate data of several fluid-surface combinations. In general, a slow spreading process as governed by the tertiary junction can be distinguished from a more rapid process which is driven by surface tension controlled internal fluid pressure. Photographs were also taken through the transparent bushings of several experimental journal bearings. Morphology of incomplete fluid films and its fluctuation with time suggest the presence or absence of unsteady phenomena of the bearing-rotor system in various arrangements.

  20. Tropical Zero Energy Office Building

    DEFF Research Database (Denmark)

    Reimann, Gregers Peter; Kristensen, Poul Erik

    2006-01-01

    of the building, so that windows are only towards the north and south, in order to reduce the solar heat gains. In order to reduce the loss of cooling through the building envelope, the walls and the roofs are heavily insulated, and the windows have double low energy glazing. The building will be lit primarily...... lighting. These measures include the use of high efficient lighting controlled according to demand, high efficiency pumps and fans, a high efficiency chiller, and use of energy efficient office equipment. The buildings PV system is connected to the grid. Solar electricity is exported to the grid during......The new headquarter for Pusat Tenaga Malaysia is designed to be a Zero Emission Office Building (ZEO). A full range of passive and active energy efficiency measures are implemented such that the building will need no more electricity than what can be produced via its own Building Integrated PV...