WorldWideScience

Sample records for ankana kokoritsu datsuryuho

  1. Development of economical and high efficient desulfurization process using low rank coal; Teitankadotan wo mochiita ankana kokoritsu datsuryuho no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Takarada, Y; Kato, K; Kuroda, M; Nakagawa, N [Gunma University, Gunma (Japan). Faculty of Engineering; Roman, M [New Energy and Industrial Technology Development Organization, Tokyo, (Japan)

    1997-02-01

    Experiment reveals the characteristics of low rank coal serving as a desulfurizing material in fluidized coal bed reactor with oxygen-containing functional groups exchanged with Ca ions. This effort aims at identifying inexpensive Ca materials and determining the desulfurizing characteristics of Ca-carrying brown coal. A slurry of cement sludge serving as a Ca source and low rank coal is agitated for the exchange of functional groups and Ca ions, and the desulfurizing characteristics of the Ca-carrying brown coal is determined. The Ca-carrying brown coal and high-sulfur coal char is mixed and incinerated in a fluidized bed reactor, and it is found that a desulfurization rate of 75% is achieved when the Ca/S ratio is 1 in the desulfurization of SO2. This rate is far higher than the rate obtained when limestone or cement sludge without preliminary treatment is used as a desulfurizer. Next, Ca-carrying brown coal and H2S are caused to react upon each other in a fixed bed reactor, and then it is found that desulfurization characteristics are not dependent on the diameter of the Ca-carrying brown coal grain, that the coal is different from limestone in that it stays quite active against H2S for long 40 minutes after the start of the reaction, and that CaO small in crystal diameter is dispersed in quantities into the char upon thermal disintegration of Ca-carrying brown coal to cause the coal to say quite active. 5 figs.

  2. FY1995 development of economical and high efficient desulfurization process using low rank coal; 1995 nendo teitankadotan wo mochiita ankana kokoritsu datsuryuho no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The objective of this study is to develop a new efficient desulfurization technique using a Ca ion-exchanged coal prepared from low rank coal and calcium raw material as a SO{sub 2} sorbent. Ion-exchange of calcium was carried out by soaking and mixing brown coal particles in milk of lime or slurry of industrial waste from concrete manufacture process. About 10wt% of Ca was easily incorporated into Yallourn coal. The ion-exchanged Ca was transformed to ultra-fine CaO particles upon pyrolysis of coal. The reactivity of CaO produced from Ca-exchanged coal to SO{sub 2} was extraordinary high and the CaO utilization of above 90% was easily achieved, while the conversion of natural limestone was less than 30% under the similar experimental conditions. High activity of Ca-exchanged coal was appreciably observed in a pressurized fluidized bed combustor. Ca-exchanged coal was quite effective for the removal of hydrogen sulfide. (NEDO)

  3. Technologies for high performance and energy saving in room air conditioners. Shoenegata kokoritsu eakon ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Kawai, N. (Toshiba Corp., Tokyo (Japan))

    1994-05-31

    An energy saving inverter type air-conditioner was introduced. It is important to increase the efficiency in the low capacity zone below the rated capacity to realize the energy saving. For the reduction of peak, improving the efficiency in the high capacity operation is also necessary. The power consumption in compressor and in inverter is about 90 % of the total power consumption in air-conditioner. The other 10 % are distributed to the fan motor and the control unit. For achieving the energy saving, the reduction of this 10 % part is also necessary because this 10 % part is constant regardless of the capacity of air-conditioner. The compressor motor was modified to the brushless DC motor with rotor position detecting device to improve the rotor structure and the position detection system. The heat exchanger was changed to a room heat exchanger with slit pattern. For the outdoor heat exchanger, the complex curvature blade fan was adopted. The control system of air-conditioner was changed. The PMV was previously learned and input in the microcomputer to calculate the data. Resultantly, the power consumption was reduced by about 20 % as compared with the conventional air-conditioner. 10 figs., 1 tab.

  4. Study on gas turbines. Leading role of high efficiency power generation; Gas turbine kenkyu. Kokoritsu hatsuden no shuyaku wo nerau

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-01-31

    This review summarizes research works of Central Research Institute of Electric Power Industry on gas turbines playing a leading role of high efficiency power generation. This article describes historical changes of gas turbine technology, changes and current status from the viewpoint of electric power industry, and development trend in various makers. Increase in the flow-in gas temperature, low NOx combustion technology, use of various fuels, and durability evaluation and improvement technology for high temperature parts are described as technological problems and development trends. The increase in temperature is indispensable for the improvement of efficiency. Materials having heat resistance, anticorrosion and strength are required. Accordingly, Ni-based single crystal super alloy has been developed. Developments of ceramic gas turbine and catalytic combustor are also described. The coal gasification combined power generation is expected as a new power generation technology having availability of various coals, high efficiency, and excellent environmental protection. Development of 1500 {degree}C class combustor for turbines has been promoted. Evaluation and improvement of durability of high temperature parts are also described. For the new utilization technology of gas turbines, repowering and compressed air storage gas turbine power generation technology are introduced. 92 figs., 14 tabs.

  5. Compressor motor for air conditioners realizing high efficiency and low cost; Kokoritsu tei cost wo jitsugenshita eakonyo asshukuki motor

    Energy Technology Data Exchange (ETDEWEB)

    Inaba, Y.; Kawamura, K.; Imazawa, K. [Toshiba Corp., Tokyo (Japan)

    2000-01-01

    The compressor motor accounts for most of the consumption of electric power in an air conditioner. To promote energy-saving, Toshiba has been progressively changing the compressor motors in its air conditioners to high-efficiency brushless DC motors. We have now developed a new compressor motor in order to achieve even greater energy-saving. A concentrated winding system was adopted featuring direct winding on the teeth of the stator core, for the first time in the industry. As a result, it was possible to realize a high-efficiency, compact, lightweight, and low-cost motor. Moreover, by constructing a new system for production, we were able to improve productivity and quality. The newly developed motor is expected to contribute to the further diffusion of energy-saving air conditioners. (author)

  6. Report of high efficiency waste power generation technology development in 1995; Kokoritsu haikibutsu hatsuden gijutsu kaihatsu (1995 nendo hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    High temperature and high pressure steam has been investigated for the high efficiency waste power generation technology development. The steam temperature below 300 centigrade is currently employed to avoid the corrosion of superheater, and the generating efficiency is less than 15%. Practical application of 500 centigrade and 100 kg/cm{sup 2} is planned by developing corrosion resistance materials. Environmental load reduction technology has been also developed. For the external circulation type fluidized bed furnace combustion tests using dummy waste in fiscal 1995, the temperature control at bag filter was effective for suppressing the dioxins. When using waste plastics, HCl could be reduced by blowing Ca compounds. Various Cr-Ni-Mo-based alloys have been developed as a corrosion resistance superheater tube material, and are currently tested. For the environmental load reduction technology, the development of pulse plasma exhaust gas treatment method has been continued from fiscal 1993. In fiscal 1995, this method was confirmed using a small-scale test unit, and also tested using a 5000 Nm{sup 3}/h bench-scale unit. The removal rates of dioxins at the outlet of bag filter were 99.8% and 99.3%, respectively. They were found to be affected greatly by the pulse waveform. 13 refs., 107 figs., 24 tabs.

  7. Report on the fiscal 1996 development of high efficient waste power generation technology; 1996 nendo kokoritsu haikibutsu hatsuden gijutsu kaihatsu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The technical development was made by which high-temperature/high-pressure steam is generated in the incineration furnace using general waste, combustible industrial waste, etc. as fuel to generate power high efficiently, and reliability of the superheater, etc. was verified by the pilot plant. For it, the following were conducted: development of element technology (high-temperature/high-efficiency combustion furnace, corrosion resistant super heater materials, environmental load reduction technology) and the demonstration (demonstrative test in pilot plant, study of an optimum total system). In relation to the external circulation type fluidized bed furnace, reformation was made which enables simultaneous sampling of dioxins, etc. The combustion test was done using the reformed combustion testing furnace to obtain the data necessary for the study of formation/decomposition mechanism of dioxin. The amount of corrosion reduction of superheater sample material for pilot plant use was determined. A study was made of improvement of removal of dioxins and NOx in the pulse plasma exhaust gas treatment method. The pilot plant was installed. 10 refs., 205 figs., 79 tabs.

  8. Fiscal 2000 survey report on R and D results of advanced clean energy vehicle; 2000 nendo kokoritsu clean energy jidosha no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    With problems inherent to clean energy vehicles such as cruising distance, fuel supply and fuel consumption, ACEVs (advanced clean energy vehicles) are in demand featuring both low pollution and high efficiency compatibly. This paper explains the fiscal 2000 results of development. The target is, by using oil-alternative fuel, to reduce driving energy consumption and carbon dioxide emission to less than half and to control the life cycle cost (total of manufacturing cost, operating cost, fuel cost, etc.) to not more than twice as much as those of conventional vehicles. As ACEVs, an ANG (adsorbed natural gas) engine and flywheel battery mounted passenger car was selected, as were a CNG ceramics engine and capacitor mounted truck, CNG engine and lithium-ion battery mounted truck, LNG engine and capacitor mounted bus, and a DME engine and capacitor mounted bus. All are hybrid systems with an energy saving device. In the research of synthetic fuels, the results of the studies were summarized including the effect of various synthetic light oils on engine performance, fuel characteristics, effect of PM grain size and the optimum properties. (NEDO)

  9. Change in catalyst properties during coal liquefaction; Kokoritsu sekitan ekika shokubai no kaihatsu (Hanno no shinko ni tomonau shokubai seijo no henka). 1

    Energy Technology Data Exchange (ETDEWEB)

    Koyama, T.; Sato, K.; Kaneko, T.; Shimasaki, K. [Nippon Brown Coal Liquefaction Co. Ltd., Tokyo (Japan)

    1996-10-28

    The purpose of this study is to prevent the deactivation of catalysts recycled in the 0.1 t/d bench scale unit (BSU). Catalysts recovered during reactions in the BSU and after reactions in the 5-liter autoclave were analyzed, to investigate the influences of the reaction condition on the property and activity of catalysts. Were used {gamma}-iron oxyhydroxide ({gamma}-FeOOH), {alpha}-iron oxyhydroxide ({alpha}-FeOOH), and natural pyrite (FeS2) as catalysts. At the S/Fe atomic ration of 1.2 under the BSU reaction condition, troilite was more easily formed from {gamma}-FeOOH compared with pyrite and {alpha}-FeOOH. As the reaction proceeded through the first, second, and third reactors, the crystal size increased, the pyrrhotite content decreased, and the troilite content increased. Deactivation due to the formation of troilite was irreversible. At the S/Fe of 3.0, however, both the formation of troilite and the crystal growth of pyrrhotite were not observed. It was found that the deactivation of catalysts can be remarkably suppressed. 5 refs., 6 figs., 1 tab.

  10. Mechanism of pyrrhotite formation from ferric oxyhydroxide catalyst; Kokoritsu sekitan ekika shokubai no kaihatsu (Okishi suisankatetsu shokubai karano pyrrhotite seisei kyodo)

    Energy Technology Data Exchange (ETDEWEB)

    Tazawa, K.; Koyama, T.; Kaneko, T.; Shimasaki, K. [Nippon Brown Coal Liquefaction Co. Ltd., Tokyo (Japan)

    1996-10-28

    It is thought that iron-based catalysts for coal liquefaction exercise their catalytic activity by forming pyrrhotite (Fe(1-x)S). However, there are still a lot of unknown problems remained concerning the formation and agglomeration behaviors of pyrrhotite. These make a difficulty for improving the activity of iron-based catalysts. In this study, sulfiding behaviors of {alpha}-iron oxyhydroxide ({alpha}-FeOOH) and {gamma}-iron oxyhydroxide ({gamma}-FeOOH) were investigated to reveal the formation and agglomeration behaviors of pyrrhotite. It was found that pyrrhotite was easily converted from ferric oxyhydroxide catalysts having large specific surface areas at the sulfiding temperature below 250{degree}C, and fine crystallites of pyrrhotite were formed at the initial stage of sulfiding. Crystal growth of pyrrhotite at the sulfiding temperature over 350{degree}C depended on the catalyst forms. It was also found that smaller crystallites of pyrrhotite were formed from {gamma}-FeOOH than from {alpha}-FeOOH and amorphous iron oxyhydroxide. 5 refs., 7 figs., 1 tab.

  11. Fiscal 1998 research achievement report. Development of key technology for high-efficiency semiconductor manufacturing process; 1998 nendo kokoritsu handotai seizo process kiban gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    In the development of large-aperture/high-density plasma technology, research and development was carried out for balanced electron drift plasma technologies for uniform control of plasma density and the like, such as an excited plasma source and plasma drift to enable wide-range plasma generation in a chamber. In the development of high-efficiency exposure technology, studies were made for stable generation and control of short wavelength excimer laser and for higher-speed large-aperture mask writing by use of an electron beam. In the development of higher-speed processing and energy-efficient technologies, research and development was conducted involving probe card technology for increasing the speed of semiconductor inspection, software-aided virtual tester technology, local energy-efficient cleaning technology in wafer processing and transportation, sheet-type flexible manufacturing system, and the like. (NEDO)

  12. Development of high-efficiency wastes-burning electric power generating technology. Volume 1. Report for fiscal 1999; Kokoritsu haikibutsu hatsuden gijutsu kaihatsu 1999 nendo hokokusho. 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper summarizes the achievements of developing a technology to generate electric power at high efficiency by using a combustion furnace that uses general wastes and combustible industrial wastes as fuel to generate high-temperature and high-pressure steam under a stabilized condition. In the developmental research of the combustion furnace, discussions were given on single-pass and double-pass type stalker furnaces, an internal circulation type fluidized bed furnace, and an external circulation type fluidized bed furnace, whereas technological prospects were established on any of them as the combustion furnace. In developing corrosion resistant super heater materials, demonstration tests were performed by using a pilot plant, corrosion mechanisms were elucidated, amount of corrosion in steam generating tubes was discussed, and corrosion life of super heaters was estimated. In developing a technology to reduce environmental load, developmental researches were carried out on a method to treat waste gases by using pulse plasma to have established nearly completely a waste gas treatment system technology. In the demonstration test using the pilot plant, the operation has started from February 1998, generating stably the steam conditions of 500 degrees C and 9.8 MPa, and the smooth operation has continued. (NEDO)

  13. Survey on the feasibility of high-efficiency gas turbine power generation system; Kokoritsu gas turbine hatsuden system ni kansuru jitsuyo kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For higher-efficiency power generation cycle plants with less restrained conditions for a location, the conceptual design of an inter-cooled regenerative two-fluid cycle plant (ISTIG) was attempted using a modified aircraft gas turbine. A high-performance turbo fan engine is used for middle-class power generation. The first stage combustion gas drives the first stage turbine, and its exhaust gas is used for the second stage combustion. Because of two-axial type of high and low pressure, improvement of thermal efficiency is expected by easy-to-install inter-cooler. ISTIG superior in operability is suitable for medium load or distributed power generation facilities, and aims at higher efficiency of a 60% level. ISTIG includes a large amount of water vapor in combustion air by adopting a diffusion type combustor eliminating back fire, and can reduce exergy loss by preheating fuel gas. Since load of the high-pressure turbine shifts toward low-pressure one by the inter-cooler, some considerations are necessary for low-pressure side cooling together with reheating cycle. Because of unnecessary steam turbine, the construction cost per kW can be reduced by 20%. 41 refs., 64 figs., 27 tabs.

  14. Fiscal 2000 report on the development of high-efficiency refuse-fueled power generation technology; Kokoritsu haikibutsu hatsuden gijutsu kaihatsu 2000 nendo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts were made to develop a refuse gasification/fusion power generation technology to contribute to the effective utilization of unexploited energy and to reduction in greenhouse gas emissions. Developed in the technology of elevating steam temperature were the evaluation of high-temperature corrosion of SH materials and a high temperature dust removing system, dechlorination technology for the thermolysis process, and a ceramic-made high-temperature air heater. For the avoidance of exhaust gas reheating, development was carried out for a low-temperature denitration unit, stable refuse feeding system for reduction in the self-heat melting critical calorific value, waste plastic injection technology for reduction in the amount of external fuel injection, and so forth. The effect of the developed element technologies were evaluated and a detailed feasibility study was conducted for a refuse gas conversion power generation system using gas engine power generation for minor-scale general waste treatment facilities. In the survey of the trend of refuse-fueled power generation technologies, trend in Japan and advanced refuse-fueled power generation systems and their introduction in Europe and America were investigated. (NEDO)

  15. Fiscal 1998 achievement report. Research and development of advanced clean energy vehicles; 1998 nendo kokoritsu clean energy jidosha no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The efforts aim to develop advanced clean energy vehicles (ACEVs) which drive on substitutes of oil low in pollution, consuming 1/2 or less energy and emitting 1/2 or less CO2 than the existing vehicles. Studies conducted in fiscal 1998 covered high-efficiency hybrid power systems and ACEVs. Efforts to develop ACEVs involved a reformed methanol fuel cell hybrid passenger car of Nissan Motor Co., Ltd. (improvement on element technologies, study of methanol concentration); CNG (compressed natural gas) engine hybrid passenger car of Honda Research and Development Co., Ltd. (improvement on flywheels, studies of ANG (adsorbent natural gas) adsorbent and ANG tank); CNG ceramics engine hybrid cargo truck of Isuzu Ceramics Research Institute Co., Ltd. (fabrication of ceramics single-cylinder engine, design and fabrication of vehicle control system, fabrication of prototype); CNG lean burn engine hybrid cargo truck of Mitsubishi Motors Co., Ltd. (studies, designing, and fabrication of engine element parts); LNG engine hybrid bus of Nissan Diesel Motor Co., Ltd. (development of engine and power storage); and DME (dimethylether) engine hybrid bus of Hino Motors, Ltd. (development of DME fuel injection system and high-efficiency power storage). (NEDO)

  16. Development of high-efficiency wastes-burning electric power generating technology. Volume 2. Report for fiscal 1999; Kokoritsu haikibutsu hatsuden gijutsu kaihatsu 1999 nendo hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In high-efficiency power generation using general wastes and combustible industrial wastes as fuel, development has been performed on a wastes gasifying and melting power generation technology. This technology is capable of suppressing generation of dioxines, recovering slag that can be utilized effectively, and reducing ash volume, by thermally decomposing the wastes and melting combustion ash at elevated temperatures by using thermally decomposed gases. With regard to the evaluation on high temperature corrosiveness of SH materials and the development of a high temperature dust removing system, a steam heater was designed, fabricated, and installed in a model plant, wherein the operation test has been performed for about 1,620 hours. For the technology of dechlorination during a thermal decomposition process, dechlorination rate of 90% was confirmed at 425 degrees C or higher in a demonstration plant. In addition, developments were made on a low temperature denitration device to avoid re-heating of waste gases, a stable wastes supply system to reduce quantity of self-heated melt limiting heat generation, and a waste plastics blowing technology to reduce external fuel charge quantity. Furthermore, a survey was carried out on the trends in wastes electric power generation technologies. (NEDO)

  17. Study of highly efficient power generation system based on chemical-looping combustion; Chemical loop nenshoho ni yoru kokoritsu hatsuden system no kaihatsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Ishida, S; Suzuki, T; Yamamoto, M [Tokyo Institute of Technology, Tokyo (Japan). Research Laboratory of Resources Utilization

    1997-02-01

    This paper describes the research and development of power generation system by means of chemical-looping combustion. For this system, fuel flows in a reduction reactor and air flows in an oxidation reactor. These two flows are separated. As a result, recovery of CO2 without energy consumption, drastic improvement of power generation efficiency, and suppression of NOx emission are expected. To realize the above, two promising candidates, NiCoO2/YSZ and NiO2/NiAl2O4, have been found as recycle solid particles between the both reactors. These have excellent oxidation/reduction cycle characteristics. By these particles as well as the existing particle, NiO/YSZ, practical application of the chemical-looping combustion is realized. Besides LNG, coal and hydrogen were considered as fuels. When using coal or hydrogen, it was found that temperature of the reduction reactor should be increased the same as that of the oxidation reactor. This is a different point from a case using LNG as a fuel. 5 refs., 2 figs.

  18. Achievement report for fiscal 1990 on research and development of high-efficiency molecule separating membrane materials; 1990 nendo kokoritsu kobunshi bunrimaku zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    In order to achieve high efficiency and energy conservation in the separation processes in the chemical industry, activities were performed to seek high-efficiency liquid separation films, gas separation films, and the related technologies that make possible separation, condensation, and refinement of substances that have consumed large amount of energy in the conventional separation processes (for example, water-alcohol, and rare gases), and substances difficult of separation and refinement because of resemblance in physical and chemical properties (for example, isomer mixed substances). For the gas separation films, research and development has been made on (1) high-order molecule recognizing films, (2) high-density metal complex fixing thin films, (3) high-functional complex films, and (4) re-activating oxygen condensation films. In (1), attempt was made on oxygen condensation by impregnating the carrier film with aqueous cobalt complex solution with regard to oxygen, for example. Research has been made on alcohol condensation film in the liquid selecting and separating films. Research and development has been made on fluororesin films for water/polar organics separation, (3) high-order structure control of water selective and permeating films, (4) water/acetic acid separating films, and (5) particle separation process utilizing liquid films. (NEDO)

  19. Development for environmentally friendly and highly efficient energy utilization system in fiscal 1998. Pt. 3. Research on highly efficient and effective energy utilization technology (Research on design technology for optimal system); 1998 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu. 3. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    This paper summarizes achievements during fiscal 1998 on researching part of the energy transportation and storage technologies, energy supply and utilization technologies, environmental load reducing technologies, and optimal system design in the 'research on highly efficient and effective energy utilization technology'. With regard to energy transportation and storage technologies, researches and developments were performed on a vacuum adiabatic transportation piping system, surfactants used for high-density heat transportation and high-density latent heat transportation technologies. In the field of energy supply and utilization technologies, researches and developments were carried out on a heat supply system using high-performance heat pumps capable of using multiple kinds of fuels, and a compression and absorption type hybrid heat utilization system. For the environmental load reducing technologies, research and development were performed on a power saving heat pump system utilizing natural coolant. In researching the optimal system design technologies, overall adjustment was made on the element technologies, whereas technological discussions and site surveys were executed by the committees at the same time. The latest achievements accomplished to date was published in a book. (NEDO)

  20. FY 1999 Technical research and development for environmentally friendly and highly efficient energy utilization system. Technical research and development for highly efficient and effective energy utilization (Technical research and development for optimum system designs - Part 3); 1999 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu seika hokokusho. 3. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    Research and development program is conducted for the elementary techniques as part of the eco-energy urban project of New Sunshine Project. Described herein are the FY 1999 results for the (techniques for transportation and storage of energy (continued), energy supply and utilization, reducing environmental loads, and designing the optimum systems). The R and D on heat transfer system through the vacuum heat insulation pipes involves fabrication, on a trial basis, the vacuum insulation covers for the vacuum insulation tubes, joints, flanges and valves for the 80A pipes, and the heat loss evaluation test for each item. The R and D on the energy supply and utilization techniques involves the heat transfer systems for a variety of fuels by the highly functional heat pump, and compression/absorption hybrid type heat-utilization system. The hybrid type heat-utilization system simulation results suggest possibility of achieving exergy efficiency of 56% as the development target by use of the new medium. The R and D on the environmental load reduction involves the power-saving type heat pump systems which use a natural coolant. (NEDO)

  1. Achievement report for fiscal 1998 on development of environmentally friendly high-efficiency energy utilization system. 2. Research of technology of effectively utilizing high-efficiency energy / research of optimum system designing technology; 1998 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu. 2. Kokoritsu energy yuko riyo gijutsu no kenkyu, saiteki system sekkei gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    This 2nd volume deals with the transportation and storage of energy in the above-named research. In search of technologies for transporting exhausted heat from the industrial area to the urban section for consumers to utilize the heat for driving their air-conditioners and hot water supply systems, the decomposition and composition reactions of methanol are utilized for a long-range transportation system. The subjects taken up in this connection include the research and development of a methanol energy system, non-equilibrium high-efficiency methanol decomposition technology, multifunctional catalysts, and highly active/selective catalysts capable of promoting reversible endoergic/exoergic reactions. Research and development is also conducted of a high-efficiency heat pump technology using hydrogen-absorbing alloys, and such a pump will realize an air-conditioning system not dependent on chlorofluorocarbon. In the research and development of a long-range heat transportation system using hydrogen-absorbing alloys, a study is made of technologies of heat/hydrogen recovery, transportation, and utilization. (NEDO)

  2. FY 1999 Technical research and development for environmentally friendly and highly efficient energy utilization system. Technical research and development for highly efficient and effective energy utilization (Technical research and development for optimum system designs - Part 2); 1999 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu seika hokokusho. 2. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    Research and development program is conducted for the elementary techniques as part of the eco-energy urban project of New Sunshine Project. Described herein are the FY 1999 results for the (techniques for transportation and storage of energy). The R and D on methanol energy systems involves the R and D on decomposition and synthesis catalyst of methanol and methyl formate for the waste heat sources of relatively low temperature. The R and D on high-efficiency techniques using hydrogen-occluding alloys involves development of heat exchangers of low sensible heat ratio, fabrication of double-effect type MH heat pump cycle devices, and demonstration tests for the system operation. It is found that the heat output of the hydrogen-occluding alloy for high temperature use is 0.18kW/kg at 90 degrees C, and that the alloy can be massively produced. A thermal utilization efficiency COP of 0.68 is obtained for the double-effect type MH heat pump cycles. The R and D on the heat-hydrogen recovery, transportation and utilization techniques involves designs and fabrication on a trial basis of a sensible heat recovery unit. (NEDO)

  3. FY 1999 Technical research and development for environmentally friendly and highly efficient energy utilization system. Technical research and development for highly efficient and effective energy utilization (Technical research and development for optimum system designs - Part 1); 1999 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu seika hokokusho. 1 Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    Research and development program is conducted for the elementary techniques as part of the eco-energy urban project of New Sunshine Project. Described herein are the FY 1999 results for the 'techniques for recovery and conversion of unutilized energy'. The R and D on waste heat recovery and conversion for chemical plants designs an internal structure of the 'wetted wall column for shell side as the stripping section' for increasing quantity of heat exchanged inside, and stably operates the bench plant for 100 hours or more. The R and D on thermoelectric power generating systems using low calorie exhaust gases involves development of materials, production of fine particle materials and sinters, and evaluation of their functions, among others. The program for application of the techniques to commercial plants confirms applicability of a 3kg thermoelectric power generating system to automobile coating process. The R and D on systems for thermoelectric recovery of low-temperature waste heat finds cracks on the ceramic plate for the power generating system WATT100, disassembled for repair. (NEDO)

  4. FY 2000 report on the results of the development of the environmentally friendly type high efficiency energy utilization system. Part 2. Study of the effective utilization technology of high efficiency energy (Study of the optimum system design technology); 2000 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu seika hokokusho. 2. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    The paper conducted the development of the environmentally friendly type high efficiency energy utilization system and the R and D of the high efficiency energy effective utilization technology, and the FY 2000 results were summed up. As to the energy transportation/storage technology, the R and D were made on the following: methanol/energy system, non-equilibrium high efficiency methanol decomposition reaction technology, development of multiple functions of catalyst, high efficiency heat pump technology using hydrogen storage alloys, heat-hydrogen recovery/transportation/utilization technology, vacuum insulated heat transport piping system, surfactant used for high density heat transport, high density latent heat transportation technology, etc. Concerning the energy supply/utilization technology, the R and D were made of the heat supply system using high efficient heat pump corresponding to multiple fuels. Relating to the environmental load reduction technology, the energy conserved heat pump system using natural coolant. As to the optimum system design technology, the comprehensive preparation of element technology, etc. (NEDO)

  5. Fiscal 1999 achievement report on research and development project on intellectual infrastructure creation and utilization technologies. Development of efficient protein expression system (Development of efficient protein expression system utilizing protein folding mechanism of hyperthermophilic bacteria); 1999 nendo kokoritsu tanpakushitsu hatsugen system no kaihatsu seika hokokusho. Chokonetsukin no tanpakushitsu oritatami kiko wo riyoshita kokoritsu tanpakushitsu hatsugen system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Efforts were exerted to achieve efficient expression of proteins of hyperthermophilic bacteria, hyperthermophilic archaeabacteria in particular, using a heterogene expression system in which Escherichia coli was the host. In an effort to search for genes related to protein folding and to elucidate the mechanism of folding, chaperonin and prefoldin subunit genes, out of various factors participating in protein folding in hyperthermophilic archaeabacteria, were cloned, and expressed in Escherichia coli. As a system for analyzing protein folding reaction, an experimental system was established on a substrate comprising isopropyl malate dehydrogenase, citrate synthase, glucose dehydrogenase, and a green fluorescent protein. Studies were further conducted to elucidate the mechanism of expression of enzyme genes in Escherichia coli for the establishment of a mass production method for useful enzymes. Also carried out was the research and development of an element technology evaluation system involving protein expression. (NEDO)

  6. Fiscal 1999 R and D project report on intellectual base creation and use technology. Development of the efficient expression system of proteins. Part 1 (Development of the system for hyperthermophilic proteins); 1999 nendo kokoritsu tanpakushitsu hatsugen system no kaihatsu gyomu seika hokokusho. 1. Chokonetsukin yurai tanpakushitsu wo kokoritsu ni hatsugensuru system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    R and D were made on the efficient expression system of hyperthermophilic proteins. Hyperthermophilic strains living in the limited tropical zone of the earth can produce heat- resistant enzyme group with activity even at more than 90 degrees C. To utilize the effective information obtained from analysis of these genomes for industries, the base arrangement of all genomes of P.horikoshii OT3 has been opened. For the efficient expression of hyperthermophilic proteins in Escherichia coli, enzyme PhFEN was improved. For Bacillus strains, new host strains were screened. Expression of several genes from hyperthermophile, P.horikoshii OT3 was tried to be expressed in T.thermophilus using expression vector pTEV131. 8 genes were selected to be expressed using T.thermophilus as a host for independent insertion of every gene. 7 genes except the gene encoding DNA polymerase I were introduced into T.thermophilus as expression plasmid, and 5 genes were also expressed active oxygen. This R and D can largely contribute to development of genome informatics technology based on DNA analysis data. (NEDO)

  7. FY 2000 report on the results of the development of the environmentally friendly type high efficiency energy utilization system. Part 1. Study of the effective utilization technology of high efficiency energy (Study of the optimum system design technology); 2000 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu seika hokokusho. 1. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    The paper conducted the development of element technology and comprehensive adjustment which are related to the development of the environmentally friendly type high efficiency energy utilization system and the study of the high efficiency energy utilization technology, and the results of FY 2000, the final fiscal year, were summed up. As to the R and D of the exhaust heat reforming/recovery system, the internal heat exchange type distillation tower was developed which has a good energy conservation effect and enables the heat supply outside. Concerning the R and D of the cogeneration system using low calorie exhaust gas, the following were conducted for further improvement of the performance of electrothermic elements: evaluation of the thermoelectric performance using bulk elements, development of new elements and evaluation of the energy balance at the time of combustion, etc. Relating to the R and D of the low temperature exhaust heat utilization cogeneration system, conducted were the development of thermoelectric materials and the fabrication/evaluation study of module. Moreover, WATT20A equipped with the original power generation module developed in this study was fabricated, and the data on the operation at the temperature of 150 degrees C were obtained by WATT-20HT. (NEDO)

  8. Development for environmentally friendly and highly efficient energy utilization system in fiscal 1998. Pt. 1. Research on highly efficient and effective energy utilization technology (Research on design technology for optimal system); 1998 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu. 1. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    This paper summarizes achievements of the researches during fiscal 1998 on researching a highly efficient and effective energy utilization technology. With regard to technologies to recover and convert unutilized energies, a process simulator was developed, basic internal structure was discussed by experiments and simulation, and substance migrating and heat exchanging characteristics were identified by using partial testing devices. These researches and developments were performed for the waste heat reforming and recovering systems used in chemical plants. In developing a thermoelectric generation system using low calorie exhaust gases, thermoelectric power generating materials were developed, a powder manufacturing technology was developed, a thermoelectric conversion element bulking technology was developed, a thermoelectric power generation system using porous structures was simulated, development and concept design were carried out on system element technologies. In the research and development of the thermoelectric generation system using low calorie exhaust gases, advanced materials and modules were manufactured, the modules were evaluated, and power generation systems were researched. In addition, researches were performed on energy transportation, supply and utilization technologies, and on environmental load reducing technologies. (NEDO)

  9. Fiscal 1999 research report. Data acquisition and analysis on the advanced high-efficiency energy system field test; 1999 nendo sendoteki kokoritsu energy system field test jigyo ni okeru data shuyaku oyobi hyoka kaiseki chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Although the next-generation phosphoric acid fuel cell has nearly reached its practical application stage as far as technology is concerned, its diffusion is yet to come due to lack of data about its cost efficiency and reliability. Under the circumstances, the goal now is to collect and analyze various data obtained in the above-named project which was started in fiscal 1997 for the compilation of data useful for full-scale diffusion in the future so that a foundation may be built for the overall popularization of the fuel cell. In this fiscal year, assessment and analysis have been conducted at 15 test sites now in presence. At the second plant of the Semboku LNG Terminals where approximately 17,000 hours have elapsed since the test began, the cell has operated for more than 16,000 hours in total. The Mycal Bore Sanda has established the longest uninterrupted operation record of 6,500. As for power generation efficiency, a town gas 13A-fueled system exhibits approximately 40% operating smoothly at a high overall efficiency of not less than 90%. (NEDO)

  10. Fiscal 2000 achievement report on the followup research on high-efficiency refuse-fueled power generation technology development; 2000 nendo kokoritsu haikibutsu hatsuden gijutsu kaihatsu no follow up kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Followup research was conducted using a high-efficiency refuse-fueled power generation pilot plant for interpolating research and development results, improvement on refuse-fueled power generation efficiency, and for introduction and popularization of refuse-fueled power generation. Operation control and safety control were performed in compliance with the pilot plant operation program, when high-temperature high-pressure steam (500 degrees C, 100 atm) was stably generated for approximately 7,600 hours in this fiscal year recording a total of approximately 22,000 hours when counted from the beginning of the verification test. Plant operation data were examined and every part of the furnace was checked and measured while the furnace was at rest, and it was found that the plant satisfied the intended specifications as refuse-fueled power plant facilities. As for its environmental impact, it was confirmed that it fully satisfied the standard values for substances in exhaust gas, which involved soot and dust, sulfur oxides, nitrogen oxides, hydrogen chloride, and dioxins. Dioxins, in particular, were far below the most rigorous legal level of 0.1ng-TEQ/m{sup 3}N. In the test of superheater materials, long-term data covering three years were acquired. (NEDO)

  11. FY 1999 report on the results of the development of high efficiency lightning conversion compound semiconductor. Plan on lighting for the 21st century; Kokoritsu denko henkan kagobutsu handotai kaihatsu seika hokokusho. 21 seiki no akari keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of developing the white light-emitting diode (LEDs) lightening as 'a plan on lighting for the 21st century,' the results of the following R and D were obtained: 1) basic study of light-emitting mechanism; 2) improvement of epitaxial growth method of blue/ultraviolet LED; 3) substrate for homoepitaxial growth; 4) basic characteristics of phosphor-based light source for white LED lighting. In 1), light emitting mechanisms responsible for high-quantum efficiency of InGaN mixed semiconductors and InGaN/GaN quantum wells were studied by means of temperature-dependent photoluminescence (PL), time-resolved PL and selective-excitation PL spectroscopy. In 2), precise lapping and polishing procedures of sapphire and GaN crystalline substrates for epitaxial growth using metalorganic chemical-vapor-deposition and MBE showed favorable surface characteristics of substrates. In 3), study was made on growth conditions and growth mechanism of GaN bulk single crystals using the nitrogen pressure-controlled solution growth method. A size of 12mm diameter of GaN single crystal showing good crystallinity and PL characteristics were obtained. In 4), excitation, absorption and PL spectra of rare-earth doped Y{sub 2}O{sub 2}S red phosphor were studied in detail. (NEDO)

  12. FY 1996 report on the cooperative research on the development of environmentally friendly high efficiency mineral resource extraction/treatment technology; 1996 nendo kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This promotion project on the cooperative research aims at developing technology to efficiently extract and recover valuable metals including in large quantity in tailings of ores in the Republic of Kazakhstan in consideration of the environmental harmony. The support study in Japan was conducted as follows. As to the Nikolayevska low grade ore, high leaching speed and high leaching rate by grain refining were made possible. The coarse grain was also possible of leaching if leached for a long time. The sulfide froth is possible of leaching in fine grain and in the temperature range of 50 degrees C. The Zhezkent tailings were possible of leaching with sulfuric acid, by aeration, and in the range of medium temperature. The sulfide froth was possible of leaching in fine grain and at temperature of 50 degrees C. After filtration/washing and regrinding, high sampling rates of bulk concentrate and pyrite concentrate were obtained by sulfide flotation by zanthate. The Zhezkent copper concentrate was tested on various factors such as grain size, temperature, and washing/no washing, to confirm effects of bacteria. In the pre-observation test on Au and Ag leaching, cyanogen leaching test was conducted using Cu leaching residue. About Cu, studied were leaching (vat leaching, flotation froth machine agitation (temperature increase, bacteria)), solvent extraction, and electrowinning. About Au and Ag, studied were cyanogen leaching and process of adsorption of activated carbon. (NEDO)

  13. FY 2001 report on the results of the follow-up study of development of the highly effective waste power generation; 2001 nendo kokoritsu haikibutsu hatsuden gijutsu kaihatsu no follow up gijutsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    For the purpose of safe operation of the highly effective waste power generation pilot plant, confirmation of the performance of corrosion resistant super heater materials under the high temperature corrosion environment, collection of the data on environmental load characteristics in waste incineration, etc., the follow-up study was made. The results were as follows: The pilot plant was able to generate high temperature/high pressure vapor stably for approximately 13,500 hours in FY 2000 and FY 2001 and for approximately 27,800 hours in 4 years since the start of the demonstrative test. The planned performance of plant facilities was fully satisfied, and the performance of environmental load reduction was fully satisfied in standard values of soot/dust, SOx, NOx, hydrogen chloride and dioxins in exhaust gas. Concerning the super heater use developmental material, its durability of 5 years or more was confirmed. It was forecast that by using this, the heightening of temperature/pressure of boiler to 500 degrees C and 100 atmospheric pressure was achieved. Further, the useful information/knowledge on plant design were obtained such as the corrosion prevention technology for waste plant and the forecast of corrosion life of materials. (NEDO)

  14. Development of high-efficiency electric-optic conversion compound semiconductor - Lighting of the 21st century. Collection of essays; Kokoritsu denko henkan kagobutsu handotai kaihatsu (21 seiki no akari) seika ronbunshu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-10-01

    Collected in this volume are essays made public in 1998-2001 under the above-named development project intended at the practical application of an illumination light source using light-emission diodes (LED) whose energy consumption efficiency will be approximately twice as high as that of the fluorescent lamp. The project aims to develop a blue/ultraviolet LED capable of high-efficiency light emission at approximately 400 nm and a fluorescent substance capable of efficient radiation of white light as excited by the said LED and to eventually combine the two for the embodiment of a 80-100 lm/W light source device. Being conducted in the field of basics of physical properties, light-emission mechanism, and crystal growth are the elucidation of the physical properties and light-emission mechanism of GaN-based compound semiconductor materials, basic studies of bulk single crystal GaN grown by the solution growth method, studies of substrate crystal surface properties, research and development of GaNAsP-based multi-color luminescent materials, etc. Studies are also under way for the research and development of LED substrates, epitaxial LED devices, and light-source devices. (NEDO)

  15. Fiscal 2000 achievement report on development of high-efficiency high-reliability welding technology through improvement on welding techniques; 2000 nendo yosetsu gijutsu no kodoka ni yoru kokoritsu koshinraisei yosetsu gijutsu no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-04-01

    Efforts are made to develop a welding design support system capable of increasing reliability and enhancing welding efficiency. Activities are conducted in the six fields of (1) the development of welding process simulation models, (2) development of welded section structure simulation models, (3) development of simulation models for predicting welding caused deformation, (4) integration of the models, (5) analysis of the welding phenomenon, and (6) the elucidation of the defect generation mechanism. In field (1), efforts are made to develop an arc plasma model, a molten pool convective heat transportation model, and a welding process model. In the effort to develop an arc plasma model, studies are made about a stationary axisymmetric arc in its steady state and about a constitutive equation and computation algorithm for developing a model in which a tungsten electrode (cathode) and an arc plasma welding pool (anode) are integrated. Furthermore, the simulation outcomes are experimentally verified. Satisfactory models are obtained as far as qualitative properties are concerned. (NEDO)

  16. Efficient second harmonics generation of a laser-diode-pumped Nd:YAG laser and its applications. Laser diode reiki Nd:YAG laser no kokoritsu daini kochoha hassei to sono oyo

    Energy Technology Data Exchange (ETDEWEB)

    Kubota, S.; Oka, M. (Sony Corp., Tokyo (Japan))

    1991-08-10

    Stabilization of the second harmonics in a laser-diode-pumped Nd:YAG laser and its application are described. The laser is a quantum noise limiting laser, in which a mode competing noise is generated from an interaction between the laser medium Nd:YAG and the type II nonlinear optical crystal KTiOPO{sub 4} when generating a second harmonics in the resonator. However, the quantum noise limiting second harmonics was obtained by means of inserting (1/4) wave length plate in the resonator to release the bond between two intersecting inherent polarization modes. This stabilized green laser is of a single lateral mode is nearly free of aberration. Therefore, an optical disc prototype having three times as much of the currently used density was made using an objective lens having high number of openings to collect lights, which was verified capable of regeneration at a high signal to noise ratio. In addition, higher output is possible by means of parallelizing the excitation, and high output is realized from edge excitation at a fiber bundle. 18 refs., 3 figs.

  17. High performance milling techniques on molding dies. Development of new roughing techniques for large molding die; Plastic kanagata seisaku ni okeru kokoritsu kako gijutsu. Ogata plastic yo kanagata no keijo arakako gijutsu no kochiku

    Energy Technology Data Exchange (ETDEWEB)

    Otsuka, H; Kohama, S; Yamakawa, M [Mazda Motor Corp., Hiroshima (Japan); Egusa, H [Mazda Tooling and Engineering Co. Inc., Hiroshima (Japan)

    1997-10-01

    It needs long time to carve a molding die of bumper, which has a large and deep cavity. To shorten the milling time, we must make the machining more performable and accurate, and develop the new technology of CAM. In the milling sequence, Primary Roughing, which cut out 90% of the stock, should be more and more performable. So we established Tilt-Plunging and Curve-Fit Spiral Cutting techniques. These techniques will reduce lateral force to the tool, and make remains more small. With the techniques, we reduced both machining and NCdata preparing time to one half. 1 ref., 14 figs.

  18. Research and development of basic technologies for next generation industries, 'high-efficiency polymeric separation membrane material'. Evaluation on first term final research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu kobunshi bunrimaku zairyo (daiikki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The first term has performed research and development placing emphasis on that 'the basic study on membrane separation is to be performed systematically to elucidate governing factors in membrane separation'. With respect to water/ethanol separation by using the penetration gasifying method, it was indicated that excellent separation performance can be exhibited by using natural polymers having sugar chain skeleton as a raw material, and by controlling the membrane structure by means of membrane manufacturing methods. For enhancement of performance in water selective permeation type separation membrane, it was shown experimentally that it is important to select a membrane suitable for the object of separation and a separation method that uses the selected membrane. Regarding the water/ethanol separation, it was shown theoretically that the penetration gasifying method can save more energy than the conventional distillation method, where the development target was presented. It was recognized that impregnation type liquid membrane using crown ether can separate amino acid optical isomers. High separation performance was obtained in carbon monoxide/nitrogen separation by using fluid carrier that uses cuprous iodine/1-methyl imidazole. (NEDO)

  19. Fiscal 1999 research report. Research on photonic measurement and processing technology (Development of high- efficiency production process technology); 1999 nendo foton keisoku kako gijutsu seika hokokusho. Kokoritsu seisan process gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 research result on R and D of laser processing technology, in-situ measurement technology, and generation and control technology of photon as laser beam source, for energy saving and efficiency improvement of energy-consumptive production processes such as welding, jointing, surface treatment and fine particle fabrication. The research was carried out by a technical center, 9 companies and a university as contract research. The research themes are as follows: (1) Processing technology: simulation technology for laser welding phenomena, synthesis technology for quantum dot functional structures, and fabrication technology for functional composite materials, (2) In-situ measurement technology: fine particle element and size measurement technology, (3) All- solid state laser technology: efficient rod type LD-pumping laser module, pumping chamber of slab type laser, improvement of E/O efficiency of laser diode, high-quality nonlinear crystal growth technology, fabrication technology for nonlinear crystals, and high-efficiency harmonic generation technology. Comprehensive survey was also made on high- efficiency photon generation technologies. (NEDO)

  20. Report of the results of the fiscal 1997 survey. R and D of high efficiency clean energy vehicles; 1997 nendo chosa hokokusho. Kokoritsu clean energy jidosha no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of developing an automobile which keeps low pollution using petroleum substituting clean energy, decreases the running energy consumption to a half at least, and reduces the CO2 emission to less than a half of the conventional one at the same time, the R and D started in fiscal 1997. As to the study of a high efficiency hybrid power system, conducted were the prediction of fuel consumption performance of the system proposed, evaluation of element technology using hybrid simulator, evaluation experiment on a new hybrid vehicle, and grasp of overseas trends. In relation to the development of hybrid vehicles, the following were studied: methanol fuel cell loading hybrid vehicle, CNG engine loading hybrid vehicle, CNG ceramic engine loading hybrid truck, CNG lean burn engine loading hybrid truck, LNG engine loading hybrid bus, and DME engine loading hybrid bus. Besides, a survey on synthetic fuel and the related survey were carried out. 17 refs., 185 figs., 101 tabs.

  1. Study of immersed heat exchange surface for high efficiency heat recovery from wire rim tires in a fluidized bed boiler; Hai tire nado kara no kokoritsu netsukaishuyo ryudosho boiler no sonai dennetsukan no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Oshita, T; Nagato, S; Miyoshi, N; Hosoda, S [Ebara Corp., Tokyo (Japan)

    1996-07-10

    In an ICFB boiler, the fluidized bed is separated by a partition into the main combustion and the heat recovery chambers. The flows in these chambers are generated by using silica sand as the fluidizing medium. To determine the overall heat transfer coefficient (HTC) of the boiler`s panel type immersed heat transfer tulles, combustion tests were performed with wire rim tires. The overall HTC of a panel tube array was lower than that of a zigzag tube arrangement. In practice, the heat absorbed by the fins makes the coefficients of either type of tube array almost identical. The air flow rate in the circulating bed at the loot Tom of the heat recovery chamber can be changed to control the overall HTC to a value virtually identical with that of a zigzag tube array. The combustion of wire rim tires leads to a buildup of wires in the zigzag array hampering the transfer of heat. Yet, the panel type array showed no buildup so that it was possible to maintain steady operation with this type of tube arrangement. 8 refs., 10 figs., 2 tabs.

  2. Research report of fiscal 1997. Survey on creation of high-efficiency renewable resources, and bioconversion technology; 1997 nendo chosa hokokusho. Kokoritsu saisei kano shigen no sosei narabi ni bioconversion gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Survey was made on material production technology using creation technology of high-efficiency renewable resources (photosynthesis reaction of plants). Industrially usable plant resources in overseas countries and Japan were arranged, and plant resources unused for food were also surveyed. The present state of genetic engineering necessary for metabolic engineering of higher plants such as fit and high-expression technology of genes, plant cell cultivation, and control technology of plant cell multiplication is described, and elementary technologies required for future gene-recombined plants are predicted. Survey was also made on the trend of creation technology of industrial plants for fat and oil, biodegradable polyester, amino acid, cellulose, fiber (cotton) and forest wood. A patent list on plant biotechnology was prepared, and study on bioconversion of plant resources was also surveyed. Overseas R & D trends on conversion and effective use technologies of renewable bio- resources are reported, and process design and its profitability were evaluated through a case study. 414 refs., 87 figs., 55 tabs.

  3. 1998 report on development of high-efficiency waste power generation technology. 2. Development of waste gasification and ash melting power generation technology; 1998 nendo kokoritsu haikibutsu hatsuden gijutsu kaihatsu seika hokokusho. Haikibutsu gas ka yoyu hatsuden gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In regard to waste gasification and ash melting power generation, a basic test and examination were conducted in fiscal 1998, with a full-scale development test made ready to start. In the development of technology for raising steam temperature, evaluation of high temperature corrosivity of SH materials and development of high-temperature dust removal system were carried out for example, as were development of dechlorination technology for thermal decomposition process and development of ceramic high-temperature air heater. In the development of technology to prevent exhaust gas reheating, preliminary examination was made on denitrification technologies using a catalyst with superior low-temperature activity. In the development of technology to reduce self-heat melting critical calorific value, investigation and basic test were carried out concerning a stable waste feed system, with a pilot test device experimentally manufactured and tested based on the findings. In the development of technology for reducing external fuel input, examination and analysis were performed on pretreatment techniques for waste plastics, with basic data obtained for a waste blowing system project. In addition, the thermal decomposition and combustion characteristics of waste plastics were clarified by the basic test. (NEDO)

  4. Fiscal 1997 report of the development of high efficiency waste power generation technology. No.2 volume. Pilot plant verification test; Kokoritsu haikibutsu hatsuden gijutsu kaihatsu (pilot plant jissho shiken). 1997 nendo hokokusho (daini bunsatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    As to a high efficiency waste power generation system using general waste as fuel, the details of the following were described: design/construction management and operational study of pilot plant, design/manufacture/construction of pilot plant, and study of an optimal total system. Concerning the construction management and operational study, the paper described the application for governmental/official inspection procedures and taking inspection, process management of pilot plant, site patrol, safety management, management of trial run of pilot plant, drawing-up of a verification test plan and test run, etc. Relating to the design/manufacture/construction of pilot plant, an outline of the pilot plant was described. The paper also stated points to be considered in design of furnace structure and boiler structure, points to be considered of the verification test, etc. As to the study of an optimal total system, the following were described: survey of waste gasification/slagging power generation technology, basic study on RDF production process, survey of trends of waste power generation technology in the U.S., etc. 52 refs., 149 figs., 121 tabs.

  5. FY 1995 report on the cooperative research on the development of environmentally friendly high efficiency mineral resource extraction/treatment technology; 1995 nendo kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This promotion project on the cooperative research aims to efficiently extract and recover valuable metals (gold, silver, copper, rare metal, etc.) including in large quantity in tailings of ores in the Republic of Kazakhstan. In FY 1995, conducted were the field survey, support study in Japan, acceptance of researchers from Kazakhstan, conceptual design of pilot plant, etc. The ore/mineral for Cu is mainly an alteration ore of chalcopyrite. Au and Ag are low grade and unknown, and the main gangue mineral is pyrite. The low grade ore (waste/much) of the Nikolayevska mine has a tendency to leaching at normal temperature, but the ore of mostly chalcopyrite such as tailings from each place has difficulty in leaching. It gets leaching by increasing temperature. The more the temperature rises, the more conspicuous the reaction becomes. Further, chalcopyrite is leached with priority over pyrite. From the result, a technical potentiality was obtained of leaching of low grade chalcopyrite in tailings mostly of pyrite. The existence of Thiobacillus ferrooxidans was confirmed. As to the recovery method for Au and Ag, CIC is studied. The process of waste/much is solvent extraction, electrowinning study and leaching, and that of tailings is bacteria leaching and leaching study. (NEDO)

  6. Research and development project in fiscal 1988 for fundamental technologies for next generation industries. Achievement report on research and development on high-efficiency polymer separating film materials; 1988 nendo kokoritsu kobunshi bunrimaku zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-03-01

    In order to achieve improvements in efficiency and energy conservation in the separating processes used in the chemical industries, research and development has been performed on liquid separating films, air separating films, and their related technologies. This paper summarizes the achievement in fiscal 1988. In the research of high-level molecule recognizing film in the air selecting and separating films, researches were made on the elementary technologies for the mechanism of reaction of O{sub 2} carrier with O{sub 2}, reversible reactivity of CO carrier with CO, and carrier fixation. In the research of high-density metallic complex fixing thin films, investigations were made on the oxygen affinity and temperature characteristics of active type CoVPH complex involved in carrier transportation in the polymeric complex interface film. In the research of high-function complex films, development was performed on a new carrier that can be dispersed stably and finely without making association even under high concentrations. Conditions for compounding into hollow fibers were discussed, and the film forming conditions for composite films having no pinholes were discovered. With regard to the liquid selecting and separating films, researches were made on the alcohol condensing film, water-polar organics separating fluorine-based polymer film, structural control on water selective permeation film, and water-acetic acid separating film. (NEDO)

  7. Fiscal 1998 research report. Development of high- efficiency electrooptic conversion compound semiconductors (21st century light project); 1998 nendo kokoritsu denko henkan kagobutsu handotai kaihatsu seika hokokusho. 21 seiki no akari keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This research aims at development of efficient lighting sources using high-brightness white LEDs. 4 research programs are as follows: (1) Basic study on emission mechanism and crystal growth, (2) Improvement of epitaxial growth methods for blue and ultraviolet LEDs, (3) Substrates for homoepitaxial growth, and (4) Basic properties of white LED lighting sources. The research results are as follows. The emission mechanism was clarified both in InGaN epitaxial layers and quantum-well structures by means of ultra-fast time-resolved spectroscopy linked with femto-second laser and the dependence of magnetic and electric fields. For reduction of a lattice defect density, an optimum thin-film crystal growth method was developed. As a new growth method of bulk single crystal substrates, a low-pressure vapor-phase growth method using radical nitrogen plasmas was developed to study synthesis of GaN and formation of single-crystal GaN. The prototype LED lighting source was prepared by using the white LEDs of 8 lm/W supplied from this project for basic study on its electric and heat radiation characteristics, and a light-guiding plate system. (NEDO)

  8. FY1996 research cooperation for the development of the environmentally friendly technology for highly efficient mineral resources extraction and treatment; 1997 nendo kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The above-named project aims to jointly develop technologies to efficiently extract and recover valuable metals (gold, silver, copper, rare metals, etc.) from slag, with caution fully exercised to conserve the environment, for effectively utilizing non-ferrous resources in the Republic of Kazakhstan. The effort covers a seven-year period beginning in fiscal 1994. The elements which are studied are technologies that involve leaching, solvent extraction, electroextraction, recovery of gold and silver, and waste water treatment. In this fiscal year, wet treatment, gold and silver treatment, and waste water treatment are studied in on-site joint researches and in domestic researches for specimens sampled at the Kazakhstan site. In addition, based on the results of the above-said basic researches, some parts of the pilot plant to be constructed is designed and manufactured. For propelling forward the project, equipment necessary for joint research is procured and forwarded to the site, and Kazakhstan scientists are invited to Japan for training. (NEDO)

  9. Fiscal 1996 comprehensive report on R and D on advanced chemical processing technology; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu sokatsu hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu / sekiyu seisan system fushoku boshi gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    R and D was conducted on technology for composite thin film formation such as laser MOCVD, for thin film lamination, and for synthesis reaction and characterization in compounded fields where temperature/pressure/magnetic field/electrical field, etc., are compounded, for the purpose of creating materials with functions newly added or reinforced by regulating compositions and structures through atomic/molecular orders. The R and D was conducted on 24 themes, which were rearranged into four categories. Examples of the themes are as follows; development of super hard permanent magnets by crystallization process control of Nd-Fe-B amorphous alloys, as for structural control technology; research on high functional thin film sensors (PbLaTiO{sub 3}) using laser MOCVD, and research on ultra thin film by multi-ion-beam sputtering with ion/photo irradiation, as for thin film technology; R and D on highly ordered structure control technology in electrode surface compounded reaction fields, as for compounded fields; and, research on diagnostic technique for compounded reaction fields by laser-ionization method, as for supporting technologies. (NEDO)

  10. Survey report for fiscal 1998. Survey of creation of highly efficient renewable resources and bioconversion technologies; 1998 nendo chosa hokokusho. Kokoritsu saisei kano shigen no sosei narabini bio conversion gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A survey is conducted concerning environmentally friendly industrial technologies that utilize renewable resources, which are technologies of creating highly renewable resources and converting renewable resources by breeding industrial vegetation. In relation with the creation technologies, the state of research and development of basic technologies is surveyed, which involves the fabrication of environmental stress resisting vegetation, studies for the application of the gene expression control mechanism, introduction of multigenes and site-directed genes, etc. Concerning the respective target products expected to be produced by industrial vegetation, as much information as possible relative to genes is collected on the current state of production, metabolism in vegetation and microbials, and biosynthesis. Surveyed in relation with the bioconversion technology are the conversion of vegetation-derived polymers, construction of environmentally friendly ligno-bioprocess, conversion of sugar, production of biofuels, etc. Furthermore, the technology of treating ligneous wastes with supercritical water is surveyed, this to determine the practicality of the technology at the current stage. (NEDO)

  11. Research and development of basic technologies for next-generation industry. Ultimate evaluation report on research and development of highly efficient polymeric separation membrane material; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu kobunshi bunrimaku zairyo saishu kenkyu kaihatsu hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-05-01

    For the enhancement of separation process efficiency and energy efficiency in the chemical industry, etc., basic technologies are developed involving high-performance separation membrane materials which are excellent in durability and usable in the field where separation by membranes has been impractical. The liquid mixtures subjected to separation are a neutral organic compound/water system, an acidic organic compound/water system, and a polar organic compound/water system; the gas mixtures subjected to separation are an oxygen/nitrogen system and a carbon monoxide/nitrogen system. After a 10-year/3-phase development endeavors, the initially intended goals are sufficiently achieved. Among those that have to be mentioned is the development of a nonaqueous separation membrane, a supported liquid membrane with amino acid optically active high performance separation capability, a high-precision evaluation unit for gas separation membrane characteristics, a selective permeation membrane with high-level oxygen and carbon monoxide carriers and reactivation technology, a high-performance ethanol separation membrane, a water/polar organic compound separation membrane, and a water/acetic acid separation membrane and stability providing technology. In particular, the water selective permeation membrane for a mixture of water and alcohol has already arrived at the stage of bench plant demonstration. (NEDO)

  12. FY 1998 annual summary report on photon measuring/processing techniques. Development of the techniques for high-efficiency production processes; 1998 nendo foton keisoku kako gijutsu seika hokokusho. Kokoritsu seisan process gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The objectives are set to develop the techniques for energy-efficient laser-aided processing; techniques for high-precision, real-time measurement to improve quality control for production processes and increase their efficiency; and the techniques for generating/controlling photon of high efficiency and quality as the laser beam sources therefor, in order to promote energy saving at and improve efficiency of production processes consuming large quantities of energy, e.g., welding, joining, surface treatment and production of fine particles. The R and D themes are microscopic processing technology: simulation technology for laser welding phenomena; microscopic processing technology: synthesis of technology for quantum dot functional structures; in-situ status measuring technology: fine particle elements and size measurement technology; high-power all-solid-state laser technology: efficient rod type LD-pumping laser modules and pumping chamber of a slab-type laser; tightly-focusing all-solid-state laser technology: improvement of E/O efficiency of laser diode, high-quality nonlinear crystal growth technology and fabrication technology for nonlinear crystal; and comprehensive investigation of photonics engineering: high-efficiency harmonic generation technology. (NEDO)

  13. FY 2000 report on the survey of the development of high efficiency photoelectric conversion compounds. Plan on the Light for the 21st Century; 2000 nendo kokoritsu denko henkan kagobutsu handotai kaihatsu seika hokokusho. 21 seiki no akari keikaku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The paper described the results of the FY 2000 R and D on the Plan on the Light for the 21st Century. For the purpose of developing the white light emitting diode lighting technology, the results were obtained in the following four items: 1) basic study on the light emitting mechanism; 2) epitaxial growth in blue light/ultra violet LED and evaluation of LED characteristics; 3) substrates and characteristics for homo-epitaxial growth; 4) basic characteristics of phosphor and white light LED lighting use light source. In 1), for the purpose of clarifying the light emitting mechanism in InGaN mixed crystal semiconductor and InGaN/GaN quantum well structure, temperature dependency of time resolved light emitting spectroscopy and selective excitation light emitting spectroscopy was measured to get information/knowledge. In 2), evaluated were characteristics of multi-quantum well UV-LED composed of AlGaN/InGaN. In 3), in the GaN crystal growth by the pressure control solution growth method, studied were effects of the increasing speed of nitrogen pressure on the size of GaN monocrystal and the surface state. In 4), verified were the measuring method of quantum efficiency of three primary color phosphor materials and problems on the measured values. (NEDO)

  14. FY 1999 report on the potential survey of the environmentally friendly type coal utilization system. Potential survey of the spread of high efficiency coal boiler; 1999 nendo kankyo chowa gata sekitan system kanosei chosa. Kokoritsu sekitan boira fukyu kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of reducing the coal consumption amount and reducing the emission amount of environmental pollutants, study of small stoker boilers in China was made in terms of sampling of the data on changes in boiler efficiency caused by combustion conditions and how to improve efficiency. As objects of survey, one boiler use plant in Beijing city and two in Taiyuan city, Shanxi province, were selected to make site survey on the state of installation and operational management of coal boiler. As a result of the actual measurement of boiler efficiency at the plants, the boiler efficiency was the maximum, about 76%, in Beijing city and the minimum, about 51%, in Taiyuan city. In China, the number of boiler with the Beijing city level was extremely small, and most of the boilers were the same as the Taiyuan city level. As a result of studying how to improve efficiency based on the survey results, the following were cited as the main measures for improvement: selection of coal by boiler type and supply of the secondary air, strengthening of the combustion management by controlling furnace pressure and air amount, etc. For the selection of coal, it is necessary to set up a system to be supported by the whole country or the whole department. (NEDO)

  15. Research and development project in fiscal 1989 for fundamental technologies for next generation industries. Achievement report on research and development on high-efficiency polymer separating film materials; 1989 nendo kokoritsu kobunshi bunrimaku zairyo no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-03-01

    With an objective to improve efficiency and energy conservation in separation processes used in the chemical industry, researches have been performed on high-efficiency liquid separating film and air separating film materials. This paper summarizes the achievements in fiscal 1989. With regard to molecule recognizing films, researches were made on oxygen and carbon monoxide carriers, and on the elementary technology for fabricating the carrier films. In the research of metal complex fixing thin films, discussions were given on causes for deactivation in complex films. In the research of high-functional complex films, discussions were given on the structure of polymer ligand/carrier complex system solid films, and on oxygen adsorption and desorption properties. Solid film structures were selected that suit the oxygen separating films. In the research of alcohol condensation films, discussions were given on polydimethylsiloxane constituent that shows ethanol selectivity and permeability, and a multi-phase system polymeric film composed of one other constituent. In the research of water-acetic acid separating films, the basic performance of polyurea film was discussed, and evaluation was given by means of a durability test. In the research of particle separation method utilizing liquid films, a prototype continuous particle separating device was fabricated. (NEDO)

  16. Fiscal 1997 report of the development of high efficiency waste power generation technology. No.1 volume. Element technology development; Kokoritsu haikibutsu hatsuden gijutsu kaihatsu (yoso gijutsu kaihatsu). 1997 nendo hokokusho (daiichi bunsatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Following the previous fiscal year, the technology development was conducted of a high efficiency waste power generation system using general waste as fuel. In the development of high temperature high efficiency combustion furnace, a combustion test on the external circulating fluidized bed incinerator was made to obtain data on formation/decomposition of dioxins. Moreover, a combustion test was conducted using mock refuse, petroleum-derived waste and waste plastics, to confirm stabilized combustion characteristics and low pollution. In the development of a corrosion resistant superheater, made were the stress load high temperature corrosion test, study of intergranular corrosion by elements of impurities, etc. In the development of the environmental load reduction technology, conducted was the conceptional design of pulse plasma exhaust gas disposal equipment corresponding to the actual one. In the verification test in a pilot plant, the pilot plant passed the pre-use inspection and was completed in February 1998. In the study of an optimal total system, discussed were the data on the pilot plant verification test, measuring points, how to arrange them, etc. 2 refs., 88 figs., 50 tabs.

  17. Fiscal 1997 survey report. Preparatory survey for a manual on the introduction of high efficiency thermal utilization systems; 1997 nendo chosa hokokusho. Kokoritsu netsu riyo system donyu manual no sakusei choa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    To cope with the energy issue and global environmental issue, it is necessary to forcibly promote energy conservation. In the light of the present situation that in Japan only 1/3 of the primary energy consumed is effectively used, policies are being prepared for promotion of the introduction of high efficiency thermal utilization systems including `a project for formation of the environmentally friendly type energy community` promoted by NEDO. However, it is hard to say that the introduction is being actively promoted. The cause is that they do not fully understood the present status of high efficiency thermal utilization systems, procedures for introduction, subsidy system, etc. Therefore, a manual was made to present to self governments and enterprisers who are planning to introduce the system. To be concrete, there are the six systems: cogeneration use thermal supply system, unused energy use thermal supply system, heat storage use thermal supply system, waste use thermal supply system, plant surplus energy use thermal supply system, and cascade type thermal supply system. 28 refs., 38 figs., 42 tabs.

  18. Survey report for fiscal 2000 on survey of high-efficiency gasification technology of catalyst utilization type; 2000 nendo chosa hokokusho. Shokubai riyo gata kokoritsu gas ka gijutsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Survey and experimental research have been carried out on coal gasification using a pressurized internal circulation fluidized bed, spouted bed hydrogenation pyrolysis, supercritical water gasification, and a possibility of efficiency improvement by utilization of catalyst in chemical raw material production spouted bed gasification system. In the coal gasification using the pressurized internal circulation fluidized bed, an experiment was performed by using active alumina and Ni catalyst, where outstanding effect was identified. In the spouted bed hydrogenation pyrolysis, an experiment was executed by using iron hydroxide catalyst, but no noticeable effect was recognized. In the supercritical water gasification, an experiment was carried out by using Na{sub 2}CO2 and K{sub 2}CO{sub 3} catalysts, where it was found that the effect of the catalysts is little in the supercritical gasification reaction area of 800 degrees C. The power generation system composite with the chemical raw material production spouted bed gasification is a one-path system in which coal is gasified by the spouted bed gasification furnace, catalyst and steam are put into a heat exchanger to perform DME synthesis, and non-reacted gas is supplied as gas turbine fuel. Estimation was made on the possibility by an on-the-desk study, which requires experiments in the future. (NEDO)

  19. FY1995 study of highly efficient power generation system based on chemical-looping combustion; 1995 nendo chemical loop nenshoho ni yoru kokoritsu hatsuden system no kaihatsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Synthesis of highly efficient and low emission power generation plant with chemical-looping combustion using various fuels such as natural gas, coal gas and hydrogen. Development of new looping materials with suitable reactivity, regenerative ability, and avoidance of carbon deposition. To obtain the design data for demo-plant by using the current experiment high- pressure fixed bed reactor. From the viewpoint of application of the proposed power generation system with chemical-looping combustion, the following main results were obtained. 1. New looping materials: NiO/NiAl{sub 2}O{sub 4}, CoO-NiO/YSZ, and Co{sub 3}O{sub 4}/CoAl{sub 2}O{sub 4}. These materials have high reactivity, repeatability, and avoidance of carbon deposition which play important roles in application of this new combustor. 2. NO{sub x} formation can be completely avoided; both fuel NO{sub x} in reduction reactor for coal gas as fuel and thermal NO{sub x} in oxidation reactor. 3. It is identified from the experiment using fixed bed reactor with the elevated pressure that NiO/NiAl{sub 2}O{sub 4} is a suitable material for coal gas or hydrogen. These promising results have provided valuable data for industrial application. (NEDO)

  20. Report on the investigational study on the technical trend of temperature control materials for high efficiency LED lighting use; Kokoritsu LED shomeiyo no ondo seigyo zairyo no gijutsu doko ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of the innovative conservation of lighting use energy, a project is being promoted with the aim of developing light emitted diode (LED) and commercializing lighting use light source substituting for fluorescent light. In this study, the following were conducted: literature survey on Peltier materials as temperature control materials for high efficiency LED lighting and the making of them as elements, extraction of technical subjects in the commercialization of LED cooling use Peltier element materials, market surveys/analyses were made of the fields of application including the LED cooling use field. As a result, for the commercialization of temperature control use Peltier elements of lighting use LED, the desirable performance index is 5x10{sup -5}/K or more. Bi{sub 2}Te{sub 3} elements which are now commercially available as Peltier elements are not good in performance and have the toxicity problem. As a candidate of temperature control use materials of lighting use LED, Mg{sub 2} (Sn, Si) or clathrate system are regarded, but the point, etc. were pointed out that it is necessary to improve thermoelectric characteristics. (NEDO)

  1. Fiscal 2000 achievement report on project for research and development of technologies for intelligent infrastructure creation and utilization. 'Development of high-efficiency protein expression system - 1 Development of system capable of high-efficiency expression of hyperthermophile-derived protein'; 2000 nendo chiteki kiban sose riyo gijutsu kenkyu kaihatsu gyomu seika hokokusho. Kokoritsu tanpakushitsu hatsugen system no kaihatsu -1 (Cho konetsukin yurai tanpakushitsu wo kokoritsu ni hatsugen suru system no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was conducted aiming at the establishment of a system to enable the high-efficiency expression of the gene products of P. horikoshii OT3 and A. pernix K1. In an effort to develop a high-efficiency protein expression system with Escherichia coli acting as the host, studies were made about the expression of hyperthermophile protein by arginine rare codon elimination, and Ph FEN (flap endonuclease) was successfully overexpressed. In the development of Bacillus strains, screening was conducted for novel hosts, and a library was constructed for a screening task suitable for hyperthermophile-derived protein production. A system was also constructed capable of the high-throughput expression of various kinds of genes using Bacillus brevis. In the study of the expression of hyperthermophile-derived genes using T. thermophilus, promoter replacement resulted in an approximately 2-fold increase in representation at the maximum. Moreover, studies were made about the length at which foreign genes were efficiently incorporated into the T. thermophilus genome. (NEDO)

  2. Achievement report for fiscal 1992 on Sunshine Program-entrusted research and development. Research and development of high-efficiency solar cells (Research on forbidden band width optimization); 1992 nendo kokoritsu taiyo denchi no kenkyu kaihatsu seika hokokusho. Kinsei taifuku no saitekika no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    Research is carried out on technologies concerning CuInSe{sub 2} thin-film solar cell manufacturing, thin film formation, thin film characterization, CdS, (CdZn)S formation, CuInSe{sub 2} single junction, analysis of the a-Si/CuInSe{sub 2} tandem solar cell operating theory, etc. In relation with the encapsulated selenization method for film formation for CuInSe{sub 2} thin-film solar cells, film constitution, film thickness, selenization temperature, etc., are studied for optimization. In relation with the vaporized selenization method, vaporized selenization is tested in a vacuum chamber aiming at improved homogeneity and reproducibility. In research on CdS and (CdZn)S which are window layer materials for CuInSe{sub 2} thin-film solar cells, CdS thin films are formed in a solution growth method using CdSO{sub 4} and (NH{sub 2}){sub 2}CS. In relation with the solution growth of the (CdZn)S crystal film, control of the Zn content in the film is now practicable. In the study of a-Si/CuInSe{sub 2} tandem solar cells, an analytical program is formulated, and calculation is made concerning the impacts of CuInSe{sub 2} forbidden band width and a-Si i-layer thickness. (NEDO)

  3. FY 2000 report on the survey of the project to promote and support the formation of the environmentally friendly energy community. Feasibility study on the waste utilization high efficiency power generation project; Kankyo chowagata energy community keisei sokushin jigyo chosa hokokusho. Haikibutsu riyo kokoritsu hatsuden jigyo ni kakawaru FS chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    An investigational study was conducted on energy recovery (power generation) in disposal of industrial waste. The capacity of power generation facilities in incineration processing of industrial waste reached approximately 200,000kW (50 facilities) in the total nationwide. The incineration-processed waste is mainly chips of wood, waste tire and bagasse. Almost all the electric power is for non-utility use, and there are no examples of selling it outside. In the metropolitan area, there is only one example of the industrial waste incineration power generation in Tochigi prefecture. This is because there are extremely very few enterprises which are sources producing the waste as target. However, if the industrial waste market is targeted, there is a future. The industrial waste has a lot of disadvantages as power generation use fuel because of its diversification, but the use of it as fuel is technically easier than the use of the general waste as RDF. Accordingly, it can be used for power generation with no need of special technology or facilities. When picking up facilities with a potentiality of high efficiency power generation from the existing incinerators in operation of persons in charge of industrial waste processing, approximately 125,000 kW can be obtained only from remodeling of the existing facilities. (NEDO)

  4. Report on the results of the fiscal 1997 R and D under consignment from NEDO of photon measuring/processing technology (development of high-efficiency production process technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku photon keisoku kako gijutsu (kokoritsu seisan process gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Development is made of high energy-efficiency laser processing technology and high efficiency/high grade photon generation/control technology as laser light source, for the purpose of energy conservation/efficiency heightening of production processes which require a large amount of energy such as welding, joining, surface treatment, and particle fabrication. As to keyhole dynamics of the molten metal generated on the laser weld, construction of simulational mathematical models was started. Equipment to fabricate semiconductor ultrafine particles which become the core of quantum dot functional structures was designed to fabricate particles. In-situ optical measuring technology was studied of element/size of particles of below 30 nm in size by emission spectroscopy associated with the plasma irradiation. As tightly focusing all-solid-state laser technology, studied was the wavelength conversion method in which harmonics are generated four times as much as the fundamental wave due to high efficient generation of high power UV laser. Also studied were high laser strength, low optical losses, conditions for fostering high homogenity crystals. Technology for high accuracy processing of element surface was established. High efficiency photon generation technology was comprehensively investigated. 140 refs., 276 figs., 46 tabs.

  5. FY 2000 report on the results of the research and development project for the photon-aided instrumentation and processing technologies. Development of high-efficiency production process technologies; 2000 nendo photon keisoku kako gijutsu seika hokokusho. Kokoritsu seisan process gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 2000 results of development of the photon-aided instrumentation and processing technologies, aimed at improving efficiency of the production processes which have been massively consuming energy, e.g., those for welding, joining, surface treatment and granulation for producing fine particles. The program for production of the functional composite compounds by the microscopic processing technologies prepares the electrically resistant films and dielectric films by in-situ mixing two types of the ultrafine particles. The program for the in-situ measuring technology is aimed at measuring contents of the constituent components of fine particles, 30nm or less in size, to an accuracy of 10% by the emission spectroscopy, after making them plasmatic. The program for the high-power, all-solid-state laser technology is developing the excited chamber for the high-power, all-solid-state slab type laser, in order to realize the energy-efficient laser-aided processing. The program for the tightly-focusing, all-solid-state laser technology develops the highly uniform crystals by growing the GLBO crystals for producing the high-power ultraviolet laser beams, is developing the techniques for production of the wavelength converting elements, including the GLBO crystal package, and develops the wavelength conversion method by the fourth-harmonic generation with the all-solid-state laser beams as the fundamental wave, realizing the high harmonic power of 23W, for generating the high-power ultraviolet laser beams at a high efficiency. (NEDO)

  6. Research cooperation promotion business for fiscal 1998. Research cooperation in the development of environmentally-friendly high-efficiency mineral resources extracting and processing technologies; 1998 nendo kenkyu kyoryoku suishin jigyo. Kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Research cooperation was conducted in the Republic of Kazakhstan for efficiently extracting and collecting valuable metals (gold, silver, copper, and rare metals) contained in volume in the slag generated by mining operation, with caution exercised not to disturb the environment. The research items taken up for development involved technologies of the leaching of the target elements using sulfuric acid, microbes, etc.; extraction using solvents; electroextraction; collection of gold and silver; and the treatment of waste water. In fiscal 1998, the wet process and the processing of gold and silver were studied, for which the specimens sampled at the research site in and after fiscal 1996 were used. As for the fabrication of pilot plant facilities, all were completed in fiscal 1998, and part of them was transported to the research site. Procurement and transportation necessary for the joint research were also carried out. Furthermore, to ensure effective execution of the project, scientists were invited from Vniitsvetmet, the Kazakhstan research institute for non-ferrous metals, for training, who included the institute director, deputy director, patent/liaison department chief, and two researchers. (NEDO)

  7. Research cooperation promoting project in fiscal 1998. Research cooperation related to developing mine resources extraction and treatment technologies of environment harmonizing and high efficiency type; 1998 nendo kenkyu kyoryoku suishin jigyo. Kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In order to realize more effective utilization of non-ferrous metal resources, joint research cooperation is made with the Republic of Kazakhstan. It is intended that valuable metals (gold, silver, copper, rare metals, and others) contained at large quantity in ore scraps generated in association with mine operation be extracted and recovered efficiently paying considerations to the environment. The treatment process consists of the following conception: raw materials such as ore scraps are leached by sulfuric acid and microorganisms to separate and recover gold and silver; the leach liquor containing valuable metals is extracted by using solvent and recovered of copper and rare metals via an electrolytic process; and the waste water is treated and discharged. Fiscal 1998 has performed studies on the wet treatment system at the site and in Japan, the gold and silver treatment, and the waste water treatment by using samples collected from the site in fiscal 1996. Based on the results of these fundamental studies, a pilot plant was built, and all of the facility fabrication was completed in fiscal 1998. Part of the facilities has been transported to the site. To drive the project forward effectively, materials and items of equipment required for the joint research were procured and transported to the country, and at the same time Kazakhstanian researchers were received in Japan for training. (NEDO)

  8. Environment-friendly type energy and coordinated community development project. Feasibility study for industrialization of high efficiency waste-fired power generation system (industrial refuse derived fuel and gas turbine combined type); Kankyo chowagata energy community keisei sokushin. Kokoritsu haikibutsu hatsuden (sangyo RDF GT fukugogata) jigyoka FS chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    High efficiency power generation, which is useful for promoting the environment-friendly type energy and coordinated community, is investigated by combining a steam turbine power generation system using the PS-RDF (paper sludge-refuse derived fuel) and a gas turbine (GT) combined cycle. Industrialization plan for processing PS in low cost has been made to ensure the profitability by participating the wholesale power supply under the law of electric power industry. This combined system is similar to the so-called super power generation using municipal garbage, but the lower temperature of steam from GT waste heat boilers (WHB) is super-heated by the flue gas from RDF boiler, which is called advanced power generation system (A.S.S.). The total power generation capacity is 149,000 kW, which consists of three 35,000 kW units of GT and one 44,000 kW unit of steam turbine. When comparing the combined system (A.S.S.) and usual one with the independent installation of the RDF steam power generation system and a GT combined cycle, the A.S.S. provides the repowering efficiency of 7,600 kW output with exactly the same quantity of fuel input as usual one. 71 figs., 31 tabs.

  9. Fiscal 1996 survey report on overseas technology concerning R and D on advanced chemical processing technology; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu kaigai gijutsu chosa hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu / sekiyu seisan system fushoku boshi gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    R and D was conducted on technologies for ultra high purity separation/processing, ultra fine particle crystal control, and high functional organic material synthesis and support. The results were classified into four categories and, on the basis of the results, the researchers paid a visit to and had a conference with related organizations overseas, for the purpose of exchanging opinions with European and American specialists and extracting evaluation and problems of the results. On laser CVD/organic thin film technology, eight institutions including University College London were visited by the researchers, with opinions exchanged on eight subjects such as studies on synthesis of high functional metallic thin film using the laser MOCVD method. On new materials/processing technology, seven institutions including MIT were visited, with opinions exchanged on the results of four researches such as preparation of Pb-based ferroelectric thin film using multi-ion-beam sputtering method. On micro-structure characterization technology, six institutions including MIT were visited, with opinions exchanged on the results of nine studies such as micro-structure characterization by transmission electron microscopy. On ion CVD/ion implantation technology, five institutions including The University of Salford were visited, with opinions exchanged on the results of seven researches such as creation and utilization of ultra-high vacuum. (NEDO)

  10. FY1998 report on the result of R and D projects by local consortiums for immediate effects. Building of the industrial waste management plant for controlling evolution of dioxins and high-efficiency heat recovery; 1998 nendo dioxin hassei yokushi kokoritsu netsu kaishugata sangyo haikibutsuyo shokyaku hai gas shori system no kochiku seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D project has been implemented for small-size gasification melting furnace and exhaust gas treatment system to develop a small-size industrial waste incineration system capable of coping with the new standards, which simultaneously incinerates the waste and treats the resultant ashes, to control evolution of dioxins and, at the same time, recover heat at high efficiency. The studied items include controlling evolution of dioxins by removing salts of heavy metals (e.g., copper) and quenching exhaust gases in a ceramic heat-exchanger, and development of the materials for filters and high-temperature mist separators serviceable under severe conditions. For building the systems, the plant comprising a pyrolysis/gasification melting furnace, high-temperature dust collector and ceramic heat exchanger is designed, constructed and continuously operated for an extended period. As a result, it has been confirmed that the system can be operated stably, evolution of dioxins can be controlled, self-heat recovery type system can be developed, and dust can be reduced in volume. (NEDO)

  11. FY 1998 report on the results of R and D projects by local consortiums for immediate effects. R and D of high-efficiency, high-performance forming machines (HPFM) using electrophoretic techniques; 1998 nendo denki eido gijutsu wo mochiita kokoritsu takino seikei sochi (HPFM) no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The R and D project has been implemented for novel high-performance forming machines (HPFMs) which handle slurry-based stock materials, in order to impart diversified functions to a wide range of ceramic-based materials covering from traditional to fine ceramic materials, and improve their productivity. For slip casting which uses traditional slurry stock materials, electricity is passed through the work by installing electrodes in each section, to control growth speed and composition of the layers, which are inconceivable by the conventional method for each section. For casting alumina slurry as the fine ceramic-based material, the electrophoretic techniques are also applied, in an attempt to form complex shapes at high efficiency, and to control the inclined structures and compositions/structures at specific sections. For development of the machines on a trial basis for traditional materials, reduction of weight and increasing thickness of the bottom side are attempted for hand-washing bowls, leading to weight reduction of 25% at the maximum. For fine ceramic-based materials, the forming systems are developed, on a trial basis, for fine pipes and sheets. (NEDO)

  12. Report on the development of the environmentally friendly type high efficiency energy utilization system - Study of the optimum system design technology. Case study of the wide area energy supply network in the Osaka prefectural region; Kankyo chowagata kokoritsu energy riyo system kaihatsu - saiteki system sekkei gijutsu no kenkyu hokokusho. Osakafuiki ni okeru koiki energy kyokyu network no case study

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The paper worked out a model of the wide area supply network which combines the element technology being developed in the eco/energy urban project and the existing technology to apply it to the actually existing city, and the evaluation study was made of energy conservation effects, environmental preservation effects, economical efficiency, etc. The FY 2000 results were reported. In this fiscal year, a case was studied of using the exhaust heat from waste incineration plant by wide area network in the region having a plan of redevelopment/rezoning of the city of Osaka where heat is in great demand. The results of the study were as follows: The total primary energy consumption amount is reduced by 16.3-19.7% in the conventional heat insulation pipe method and by 19.2-20.6% in the vacuum heat insulation method. As to the environmental preservation, the CO2 reduction amount is 36.9-40.0%, and the NOx reduction amount is 43.7-45.5%, which indicated much more improvement than in the present situation. In the aspect of economical efficiency, the result indicated that in the case of the shortest piping, much economical efficiency is expected even without subsidies if considered of the carbon tax. (NEDO)

  13. FY 1992 report on the results of the R and D of advanced function creation processing technology. Development of technology to create high efficiency power generation use members; 1992 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    The paper described the FY 1992 results of the technology to create high efficiency power generation use members. To enhance characteristics of super-high property permanent magnet up to the theoretical level, the development was proposed of a technology to control the size/configuration of micro crystal phase in association with the crystallization of alloy amorphous. For the development of environmental purification use high functional catalysts, a refining method using laser excitation was studied. The observation was also made of molecular adsorption on the Pd thin film catalyst prepared by RF sputtering. The multi-source excitation plasma CVD was proposed which was film-formed by exciting plasma as raw gas independently for each component and supplying it to the substrate of which the periphery was separately controlled. The paper also described the development of technology for ion/light combined assist ultra-thin film production for development of gas turbine combustion sensor. The study was also made of the synthesis of higher-order structure controlled high functional organic materials using the electrode interface combined field which is composed of electrode reaction/high grade photon/extreme magnetic field. In the development of the higher-order structure control technology using the photon combined reaction field, studies were made of the photo reaction film formation technology, the basic film formation technology in the combined reaction field, and the molecular orientation technology. (NEDO)

  14. Environment-friendly type energy and coordinated community development project. Feasibility study for industrialization of high efficiency waste-fired power generation system using animal waste; Kankyo chowagata energy community keisei sokushin. Kokoritsu haikibutsu hatsuden (chikusan haikibutsu riyo) jigyoka FS chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    To introduce the power generation system fueled by animal waste (excrements), one of the so-called industrial waste, its feasibility has been studied in Koyu and surrounding area located in Miyazaki Prefecture. This report includes the technical feasibility of available quantity of animal waste, chemical analysis of the waste, and basic design of the power generation system containing the furnace model and also its economical feasibility. The available quantity of animal waste in Koyu area is about 169,000 tons a year, which can generate 10.5 MW of electric power. That including the surrounding area is about 219,000 tons a year, which can generate 15.0 MW. The heating values of animal excrements in average and as received are 970 kcal/kg for pigs and 1,230 to 2,700 kcal/kg for broilers. In the case of combustion of mixed broiler and pig excrements, both of the stoker and fluidized-bed model furnaces become refractory furnace construction and provide with heat recovery boiler due to their high moisture content. In addition, the stoker furnace model requires an excrement dryer system as pre-treatment of fuel. For the fluidized-bed furnace of 15 MW grade power plant using the mixed fuel of 50% broiler excrements and 50% pig excrements, the power generation efficiency of 23% can be expected at generator end. The generating cost is around 10 yen/kWh. 27 refs., 61 tabs.

  15. Fiscal 2000 project of inviting proposals for international joint research - invitation for international proposal (Energy conservation No.3). Achievement report on development of micro-scale boiling aided high efficiency heat removing device; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (shoe No.3). Micro scale boiling ni yoru kokoritsu honetsu device no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Studies are conducted about basic matters of heat transfer with boiling, such as critical heat flux intensification, prevention of dry-out, and the development of refrigerants suitable for use for heat transfer with boiling, for the purpose of developing boiling heat conduction type high-efficiency heat removing devices for use in electronics, and then heat removing devices usable as power devices in the future are experimentally designed. Activities are conducted in the three fields of (1) the study of basic micro-boiling technology, (2) development of micro-scale boiling element technology, and (3) international joint studies. Efforts are made to develop the technology of removing heat from ultrahigh heat fluxes using a micro-valve in field (1), to develop the technology of heat transfer by boiling in a micro-channel in field (2); and to develop the technology of critical heat flux intensification in a boiling heat exchanger in an electromagnetic field (3). In an effort to develop the technology of heat removal, a heat transfer plate is installed at the bottom of a path which is narrow, horizontal, and rectangular, and distilled water is allowed to flow and boil. Micro-bubble emission boiling occurs by a subcooling degree of 40K at an average flow rate of 0.5 m/s, and an ultrahigh heat flux of 2-7 times 10{sup 6} W/m{sup 2} is obtained. The value is 2-4 times as high as the current IC chip critical heat flux. (NEDO)

  16. Research and development of basic technologies for next generation industries, 'high-efficiency polymeric separation membrane material'. Evaluation on first term final research and development; Jisedai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu kobunshi bunrimaku zairyo (daiikki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1985-03-30

    The first term has performed research and development placing emphasis on that 'the basic study on membrane separation is to be performed systematically to elucidate governing factors in membrane separation'. With respect to water/ethanol separation by using the penetration gasifying method, it was indicated that excellent separation performance can be exhibited by using natural polymers having sugar chain skeleton as a raw material, and by controlling the membrane structure by means of membrane manufacturing methods. For enhancement of performance in water selective permeation type separation membrane, it was shown experimentally that it is important to select a membrane suitable for the object of separation and a separation method that uses the selected membrane. Regarding the water/ethanol separation, it was shown theoretically that the penetration gasifying method can save more energy than the conventional distillation method, where the development target was presented. It was recognized that impregnation type liquid membrane using crown ether can separate amino acid optical isomers. High separation performance was obtained in carbon monoxide/nitrogen separation by using fluid carrier that uses cuprous iodine/1-methyl imidazole. (NEDO)

  17. Fiscal 2000 report on result. Phase-1 R and D on closed type high efficiency gas turbine technology corresponding to recovery of carbon dioxide; 2000 nendo nisanka tanso kaishu taio closed gata kokoritsu gas turbine gijutsu dai 1 ki kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Technological development is aimed at a 500MW class gas turbine plant with a generator-end efficiency of over 60%, while using a 1,700 degree C class ultra high temperature gas turbine by natural gas fuel and fully collecting CO{sub 2} in the exhaust gas through an oxygen combustion closed type system. The paper describes the results of fiscal 2000. A conceptual design was made on the basis of a tentatively set second mass and heat balance concerning the closed cycle that facilitated CO{sub 2} recovery by methane-oxygen combustion, with a system optimization method examined by parameter studies (sensitivity analysis of the effect of each parameter on the generator-end efficiency). Using the zero-th conceptual design implemented in fiscal 1999, the first mass and heat balance (generator-end efficiency 58%) and the results of parameter studies, the system optimization was continuously examined, deciding the second mass and heat balance. A calculation of 59.8% was obtained for the generator-end efficiency. A study was conducted on a closed system verification machine based on the ME-1000 gas turbine by Mitsubishi Heavy Industries, Ltd. The premises of CRIEPI (Central Research Institute of Electric Power Industry) Yokosuka laboratory was assumed to be the installation site for the machine. (NEDO)

  18. Fiscal 1999 report on result on the model project for systematization of high-efficiency combustion of by-product gas in ironworks. Part 2/2; 1999 nendo seitetsusho fukusei gas kokoritsu nensho system ka model jigyo. 2/2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    For the purpose of reducing energy consumption of the steel industry, a large energy consuming industry in China, a model project was carried out for systematization of high-efficiency combustion of by-product gasses in ironworks, with the fiscal 1999 results compiled in the form of detailed design/documents, and the like. This project is intended for demonstration and dissemination of technologies for improving energy consumption efficiency, by controlling mixed gas calorie and oxygen content, in the reheating furnaces that consume as fuels various combustible gasses produced in iron and steel making processes. Arranged in the detailed design documentation were numerous drawings including a list of mixed gas equipment, design drawing of mixed gas orifice, specification of mixed gas control valves, list of reheating furnace equipment and devices for No.1 small plant, specification of control valves of reheating furnace for No.1 plant, list of reheating equipment and devices for slab plant, specification of calorimeter, specification of oxygen concentration meter, No.1 mixed gas wiring system diagram, and No.3 mixed gas piping/assembling manual. Also prepared were a manual for pre-shipment inspection and report on inspection findings, as well as notes on transportation, program for receiving Chinese engineers, schedule for dispatching engineers, etc. (NEDO)

  19. Research and development of basic technologies for next generation industries, 'high-efficiency polymeric separation membrane material'. Evaluation on second term final research and development (first report); Jisesdai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu bunshi bunrimaku zairyo (dainiki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    This study is intended to establish a basic technology for innovative high-efficiency separation membrane materials that can be used in areas in which application of membrane separation has been impossible. The water/ethanol separation membrane (for water selective permeation) and water/acetic acid separation membrane (for water selective permeation) achieved separation coefficient and permeation velocity of the world's highest level. The water/ethanol separation membrane (for ethanol selective permeation), although its separation coefficient is lower than the world's highest performance, has high permeation velocity, providing the performance of the worldwide level as seen from the comprehensive viewpoint. The carbon monoxide/nitrogen separation membrane achieved separation coefficient and permeation velocity of the world's highest level. The oxygen/nitrogen separation membrane requires further enhancement in the permeation velocity and stability. Establishment has been performed on separation technologies for membrane separation of non-water soluble aqueous solutions, optical division by using chiral crown ether, high-performance liquid separation by means of plasma surface treatment, and particle separation. Basic analysis has been advanced also on evaluation technologies for gaseous body separation membrane and liquid separation membrane, of which future progress is expected. (NEDO)

  20. Research report for fiscal 1998 on development of environmentally friendly high-efficiency energy utilization system. Research of optimum system designing technology (Research of effect of eco-energy city system technology introduction to Osaka); Kankyo chowagata kokoritsu energy riyo system kaihatsu Saiteki system sekkei gijutsu no kenkyu 1998 nendo chosa hokokusho (Osakafu). Ekoene toshi system gijutsu donyu koka no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Concerning the district in Osaka Prefecture selected for study in fiscal 1997, it is investigated whether energy efficiency is enhanced, and environmental impact reduced, by the introduction of element technologies, and the findings are compared with the results expected to be produced without their introduction. Problems about their introduction are also discussed. Taken up for study are the collection and utilization of heat from a water granulated slag manufacturing plant of an iron mill, exhaust heat reform and recovery system at a chemical plant, heat supply system driven by a high-performance heat pump capable of dealing with various kinds of fuels, compression/suction hybrid heat utilization system, and a cold heat supply system using microspheres. Annual energy consumption, CO2 and NOx emissions, and costs are calculated for each of them. Concerning these element technologies, various tasks are discussed, related to the technology of their systematization, economy, dissemination of district heat supply, and wide-area heat supply businesses utilizing exhaust heat. As the result, it is concluded that the primary energy consumption as a whole is reduced upon their introduction and that energy saving effect and environmental impact reducing effect are in presence. (NEDO)

  1. Achievement report for fiscal 1991 on Sunshine Program-entrusted research and development. Research and development of high-efficiency solar cells (Research on forbidden band width optimization); 1991 nendo kokoritsu taiyo denchi no kenkyu kaihatsu seika hokokusho. Kinsei taifuku no saitekika no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    Research is conducted on film formation technologies etc. for the chalcopyritic compound semiconductors represented by CuInSe{sub 2} which is the most excellent of the materials for thin-film solar cells. As for the development of a encapsulated selenization method, research is conducted on an In formation method, temperature program for heat treatment, and Cu-In alloy film selenization, and then a CuInSe{sub 2} film less to suffer phase separation is obtained. In the development of a vaporized selenization method, the reactor tube and the temperature program are improved, and this results in a CuInSe{sub 2} film excellent in homogeneity. As for the evaluation of CuInSe{sub 2} film, photoluminescence is measured using a solid-phase selenized film, vapor-phase selenized film, and 3-source vapor-deposited film, and the result shows that photoluminescence-assisted CuInSe{sub 2} film evaluation is quite promising. In the development of ZnO film formation technologies, the MOCVD (metalorganic chemical vapor deposition) technology is almost complete, and film formation on a 10cm-square substrate is now practical. (NEDO)

  2. Report on development of high-efficiency wastes power generation technology in fiscal 1998. 1. Development of component technology, and demonstration test of a pilot plant; 1998 nendo kokoritsu haikibutsu hatsuden gijutsu kaihatsu seika hokokusho. Yoso gijutsu kaihatsu (pilot plant jissho shiken) (dai 1 bunsatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A technology is developed to perform high-efficiency power generation by generating high-temperature and high-pressure steam stably by burning general wastes and combustible industrial wastes as fuel. This paper describes summary of the achievements in fiscal 1998. Corrosion tests were performed on over-heater materials under steam condition of 500 degrees C and 100 kg/cm{sup 2} by using a hot model. It was verified by the tests that the corrosion environment around an external heat exchanger is milder than that with an external stack. A circulation fluid bed was simulated from operation data, and a prospect was obtained on steam conditions required for the high-efficiency power generation. In order to elucidate the corrosion mechanism, discussions were given on deposited ash properties, corrosion characteristics and stress. Elucidation was made on a discharge chamber structure most suitable for removing dioxins and NOx by using a waste gas treatment process that uses plasma generated by discharge. A concept design was made. The economic effect of the system is equivalent to that of the activated carbon blow-in process, whereas a waste gas treatment system was nearly completed. As a result of the pilot plant test, the power generation efficiency is estimated to be 30% in a scale of 1200 tons per 24 hours. A demonstration test revealed that dioxin emission was far below the regulation value. An optimal system was also discussed. (NEDO)

  3. Achievement report for fiscal 1991 on Sunshine Program-entrusted research and development. Research and development of high-efficiency solar cells (Research on low-temperature film formation technology); 1991 nendo kokoritsu taiyo denchi no kenkyu kaihatsu seika hokokusho. Teion seimaku gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    For the establishment of a low-temperature formation technology for compound semiconductor polycrystalline thin film of CuInSe{sub 2}, research is conducted involving film formation and film quality evaluation using the ICB (ion cluster beam) method. In the research on the film formation, an In-excessive film is placed on a Cu-excessive CuInSe{sub 2} film using the ICB method for the formation of a two-layer film. Bulk CuInSe{sub 2} and thin-film polycrystalline CuInSe{sub 2} are evaluated using PL (photoluminescence) spectrums excited by YAG (yttrium aluminum garnet) and Ar. In both bulk and thin film, it is suspected that clues are latent in the levels deeper than hitherto reported. A luminescent belt of 0.75eV is detected. Changes in film quality before and after oxygen annealing are verified using the YAG-excited and Ar-excited PL spectrums, and the result suggests the feasibility of tracking the process in which the effect of annealing propagates inward from the interfacial surface. Fe-added single-crystal CuInSe{sub 2} is investigated for the optical and photoelectrical effects of Fe impurities. (NEDO)

  4. Fiscal 1992 survey report of R and D on new forming technology of composite material. Development of innovative technology for producing members for high efficiency power generation; 1992 nendo fukugo zairyo seikei gijutsu chosa hokokusho. Fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu (kokoritsu hatsuden'yo buzai soseigijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    Composite forming technology is being developed which is intended to manifest superplasticity phenomenon of ceramic matrix and metallic matrix composite materials; also being developed is an effective efficient superplastic processing technology which utilizes this composite forming technology. The related technologies were investigated comprehensively systematically with the purpose of promoting the development. First, an overview was given in the present state and problems of ceramic matrix/metallic matrix composite technologies and in the forefront of the superplasticity research of ceramic matrix materials, and then, the related technologies of these composite materials were pigeonholed under the following items: 1. assesment/strength/dynamic properties, 2. composite process and property, 3. composite forming process, 4. superplasticity, 5. process and superplasticity, and 6. others. The titles of the rearranged summary documents are, for example, surface modification and casting of SiC platelets in Al{sub 2}O{sub 3} composites, deformation of Al{sub 2}O{sub 3}/TiC composites at elevated temperatures, superplastic bulging of fine-grained zirconia, forging of short alumina fiber reinforced aluminum alloy, and on superplasticity in silicon carbide reinforced aluminum composites. (NEDO)

  5. Report on technological achievements in fiscal 1999. Institutions for research and development of new environmental industry creating type technologies (Development of harmful substance reducing device for incineration furnaces using high-efficiency power pulse technology); 1999 nendo shinki kankyo sangyo soshutsugata kenkyu kaihatsu seido seika hokokusho. Kokoritsu pulse power gijutsu wo mochiita shokyakuroyo yugai busshitsu sakugen sochi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Development has been proceeded on a harmful substance (SOx, NOx, Dioxine, etc.) reducing device for incineration furnaces that can be installed retroactively to existing incineration facilities, using high-efficiency power pulse technology of energy saving type, and discharge in honeycomb ceramics. The developmental activities were advanced by dividing them into researches on (1) research of gas decomposing devices, (2) research of pulse plasma electric power source, and (3) research of SI thyristor for pulse. In the research (1), a pulse plasma experiment and a gas decomposing experiment were performed. In the former experiment, discussions were given on effects of discharge electrode structure on discharge in the honeycomb ceramics, wherein it was made clear that employing the mesh-comb type electrode structure can realize discharge along the ceramics surface. In the latter experiment, it was revealed that the simulated gas (dibenzofuran) can be decomposed to 90% by using a coaxial cylindrical reaction device. In the research (2), studies were performed on increasing voltage and current in the device, as well as on semiconductor driving circuits. In the research (3), studies were made on the high-quality gate zone forming method and the quality conduction zone forming method. (NEDO)

  6. Environment-friendly type energy and coordinated community development project. Feasibility study for industrialization of high efficiency waste-fired power generation system using CSD and other wastes; Kankyo chowagata energy community keisei sokushin. Kokoritsu haikibutsu hatsuden (CSD nado haikibutsu riyo) jigyoka FS chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This report presents the feasibility of enterprise on power generation by thermal recycle and selling power together with volume reduction, de-harming (de-toxification) and stabilization of the shredder dust. Contents of the study include the investigation of generation amount of car shredder dust (CSD) and its properties, trial design of high efficiency power generation facilities, selection of boiler tube materials, incineration test with a melting kiln test plant, disposal and effective use of melted slag and fly ash, and environmental impact assessment. The capacity of waste disposal in the trial design contains 1,140 ton/day of shredder dust, 60 ton/day of waste plastics, sludge and waste paper, and 130 ton/day of waste oil. Melting kiln with secondary combustion chamber was adopted as the incineration type. The high temperature and high pressure waste heat boiler with an extraction condensing turbine was adopted as the waste heat recovery and power generation type. Stable combustion was confirmed from the results using a test plant. According to the consideration of cost and unit cost results for wholesale power supply, if it is postulated that income for waste disposal is 12,000 yen/ton, power generation costs in excess power selling and wholesales are 6.4 yen/kWh and 9.1 yen/kWh, respectively. 67 figs., 48 tabs.

  7. FY 2000 report on the results of the infrastructure construction project for spreading high-efficiency fuel cell systems/development of test apparatuses for evaluation of fuel cell systems for automobiles; 2000 nendo kokoritsu nenryo denchi system kiban gijutsu kaihatsu / jidoshayo nenryo denchi system hyoka shiken sochi no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This project studies the testing/evaluation methods for spreading fuel cells for automobiles. Described herein are the FY 2000 results. The problems involved in evaluation of the single cell units are classified into those involved in the cell construction and methods of evaluating the operation performances of the single cell units. These problems are analyzed mainly by literature survey. The mode simulation tests will be greatly simplified, if the system can be tested on the bench without being actually boarded on the vehicle. Therefore, this project is aimed at development of a comprehensive mode simulator which can be automatically operated corresponding to the running modes of various countries, to test the performance of FCEV and to examine the effects of each component independently on the vehicle performance. The factors required to reproduce the actual driving states of an FCEV on the bench are analyzed, and the conceptual designs are drawn for the controlling algorithms. It is necessary to standardize the stack and reformer testing methods, in order to evaluate the fuel cell system components. For these objects, the prototype units are constructed to evaluate 10kW direct hydrogen type stacks and 5kW methanol reformers. The units are also constructed to evaluate the high-pressure (1MPa) reformer reactors and hydrogen separation membrane systems. (NEDO)

  8. Fiscal 1996 survey report on overseas technology concerning R and D on advanced chemical processing technology; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu kaigai gijutsu chosa hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu / sekiyu seisan system fushoku boshi gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    R and D was conducted on technologies for ultra high purity separation/processing, ultra fine particle crystal control, and high functional organic material synthesis and support. The results were classified into four categories and, on the basis of the results, the researchers paid a visit to and had a conference with related organizations overseas, for the purpose of exchanging opinions with European and American specialists and extracting evaluation and problems of the results. On laser CVD/organic thin film technology, eight institutions including University College London were visited by the researchers, with opinions exchanged on eight subjects such as studies on synthesis of high functional metallic thin film using the laser MOCVD method. On new materials/processing technology, seven institutions including MIT were visited, with opinions exchanged on the results of four researches such as preparation of Pb-based ferroelectric thin film using multi-ion-beam sputtering method. On micro-structure characterization technology, six institutions including MIT were visited, with opinions exchanged on the results of nine studies such as micro-structure characterization by transmission electron microscopy. On ion CVD/ion implantation technology, five institutions including The University of Salford were visited, with opinions exchanged on the results of seven researches such as creation and utilization of ultra-high vacuum. (NEDO)

  9. Report on results of feasibility study in fiscal 1986 on use of coal in next generation high efficiency power generation system - research commissioned by Moonlight project propulsion room of Agency of Industrial Science and Technology. MHD generation subcommittee; 1986 nendo jisedai kokoritsu hatsuden system no sekitan gas riyo feasibility chosa kenkyu seika hokokusho (Kogyo Gijutsuin Moonlight keikaku suishinshitsu itaku chosa). MHD hatsuden bunkakai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-03-01

    A research study was done on MHD generation by coal gasificating combustion. MHD generation is a very attractive power generation system such that efficiency is as high as 55%, that preservation of the environment is superior, and that coal can be used as fuel. The open cycle seems suitable for a one million kW class as a base load following up load fluctuation of approximately 20%, while the closed cycle for 200-300 thousand kW class doing daily start-stop. With a mind to a scale of 30 MWt, in the open cycle, R and D is required in such items as a coal gas combustor, generation channel, high temperature air heater, and seed/slag recovery device. In the closed cycle, R and D is required in the generation channel, high temperature helium heater/high temperature valve, seed injection/recovery device, operation technique of helium closed loop, etc.. Moreover, as a total system, development is necessary in the areas of conceptual design and optimization method, partial load operation and DSS operation method, for example. (NEDO)

  10. Fiscal 1993 report on technological results. R and D on new forming technology of composite materials (Development of innovative technology for producing members for high efficiency power generation); 1993 nendo fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    A forming technology was developed which uses superplasticity of composite materials, i.e., high-functional materials for power generating equipment for example. Activities were conducted in the three areas of (1) ceramic based composite materials, (2) development of metal-based composite forming technology, and (3) comprehensive investigation and adjustment. In (1), with a view to finding a composite forming technology, in which high tenacity materials are obtained by evenly dispersing particles or whiskers as reinforcements in a matrix, a room temperature forming technique using fine particles was exploited, as were a high temperature forming technique using fused bodies and a possibility of manifestation of superplasticity in the prepared composite materials. The materials used were Si{sub 3}N{sub 4} matrix-SiC, Al{sub 2}O{sub 3} matrix-TiC, and glass matrix composite based materials filling ceramics in fine holes of porous glass. In (2), composite forming technologies were examined for such composite materials as Al alloy matrix-SiC particulate-based by a molten metal stirring method, Al alloy matrix-ceramics short fiber-based by a high pressure forging method, Ti alloy matrix-ceramics particulate-based by a mechanical alloying method, and Al alloy matrix-ceramics particulate-based by an alkoxide method/powder metallurgy method. (NEDO)

  11. FY 1996 report on the cooperative research on the development of environmentally friendly high efficiency mineral resource extraction/treatment technology. Basic design of pilot plant and a part of the detailed design; 1996 nendo kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku. Pilot plant no kihon sekkei oyobi ichibu shosai sekkei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This project is a cooperative research on the development of environmental harmony type high efficiency mineral resource extraction/treatment technology. It aims to study/develop a system to recover valuable metals from unused resources in the Republic of Kazakhstan using the environmental harmony type technology which is easy to operate/maintain and is environmentally friendly with no mine pollution caused. In the project, which started in FY 1994, a pilot plant is finally constructed in Kazakhstan, a recovery system to be applied is demonstrated, and the comprehensive assessment of the system is made. Concretely, the recovery of Cu, Au, Ag, etc. is tried from the Nikolayevska low grade ore and Zhezkent tailings. This is a system into which the following techniques are integrated: treatment before dressing such as flotation, leaching of Cu, etc. by acid including bacteria, solvent leaching, electrowinning, cyanogen leaching activated carbon treatment and wastewater treatment of Au and Ag. As to the design/fabrication of pilot plant, conducted was the conceptual design in FY 1995, and the basic design, a part of the detailed design (crushing/grinding/leaching/dewatering facilities of the process of the acid (bacteria) leaching of Cu, etc.), and the fabrication in FY 1996. (NEDO).

  12. Environment-friendly type energy and coordinated community development project. Feasibility study for industrialization of high efficiency waste-fired power generation system using general RDF; Kankyo chowagata energy community keisei sokushin. Kokoritsu haikibutsu hatsuden (ippainado RDF riyo) jigyoka FS chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The refuse-derived fuel (RDF) has been holding public attention not only as the energy resource of stable high calorific value for local energy development, but also as the effective method for waste treatment. As one of the effective utilization methods for waste treatment, this investigation was conducted to industrialize and establish the RDF power generation system, in which power generation and ash treatment are integrated in Tochigi Prefecture which is located inland. The base supply type was adopted as a way of operation from the menu of the electricity wholesale project of Tokyo Electric Power Co. and its rate of operation is 80 percent a year. Then, the fluidized bed combustion method, a dry exhaust gas treatment method, and continuous electric melting furnaces were decided as the RDF power generation system. According to this system, it is possible to obtain 26 percent gross thermal efficiency by conventional generation facilities. It was estimated that the expenses reduction for 15 years will be 17.6 billion yen compared with the ordinary combustion system. Also, the following effects can be expected; the reduction of CO2 emission, improvement of energy efficiency, and the extension of life of landfills capacity. 36 figs., 51 tabs.

  13. FY 1998 annual summary report on advanced fabrication techniques for high-melting metal-based members. Development of techniques for creating members for high-efficiency power generation; 1998 nendo koyuten kinzokukei buzai no kodo kako gijutsu seika hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The R and D programs were implemented to develop techniques for creating members of high-melting metals, having a very high melting point and potentially excellent high-temperature strength characteristics. These are expected to replace Ni-based superalloys for gas turbine members, to further increase operating temperature of the turbine. The programs were aimed to improve their high-temperature strength and toughness and hence their reliability by microscopically controlling their compositions and structures, and also aimed to improve their durability by coating them with a film capable of preventing oxidation and resisting to gas-induced corrosion to impart resistance to oxidation and corrosion to them. For the design of Nb-based solid solution alloys, it is found that dissolution of Mo at around 30 at.% or less and W at 20 at.% or less in Nb improves their high-temperature strength and toughness. For the design of high-strength Nb-based composite materials, it is found that Si-containing Nb-based composite materials, prepared by mechanical alloying, are amorphous or present in the form of solid solution of Ni supersaturated with Si. The R and D activities were also directed to development of techniques for creating Nb-based superhigh-temperature members, their evaluation, and imparting oxidation resistance to them. (NEDO)

  14. Research and development of basic technologies for next generation industries, 'high-efficiency polymeric separation membrane material'. Evaluation on second term final research and development (first report); Jisesdai sangyo kiban gijutsu kenkyu kaihatsu. Kokoritsu bunshi bunrimaku zairyo (dainiki kenkyu kaihatsu hyoka)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    This study is intended to establish a basic technology for innovative high-efficiency separation membrane materials that can be used in areas in which application of membrane separation has been impossible. The water/ethanol separation membrane (for water selective permeation) and water/acetic acid separation membrane (for water selective permeation) achieved separation coefficient and permeation velocity of the world's highest level. The water/ethanol separation membrane (for ethanol selective permeation), although its separation coefficient is lower than the world's highest performance, has high permeation velocity, providing the performance of the worldwide level as seen from the comprehensive viewpoint. The carbon monoxide/nitrogen separation membrane achieved separation coefficient and permeation velocity of the world's highest level. The oxygen/nitrogen separation membrane requires further enhancement in the permeation velocity and stability. Establishment has been performed on separation technologies for membrane separation of non-water soluble aqueous solutions, optical division by using chiral crown ether, high-performance liquid separation by means of plasma surface treatment, and particle separation. Basic analysis has been advanced also on evaluation technologies for gaseous body separation membrane and liquid separation membrane, of which future progress is expected. (NEDO)

  15. Fiscal 1996 comprehensive report on R and D on advanced chemical processing technology; 1996 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu sokatsu hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu / sekiyu seisan system fushoku boshi gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    R and D was conducted on technology for composite thin film formation such as laser MOCVD, for thin film lamination, and for synthesis reaction and characterization in compounded fields where temperature/pressure/magnetic field/electrical field, etc., are compounded, for the purpose of creating materials with functions newly added or reinforced by regulating compositions and structures through atomic/molecular orders. The R and D was conducted on 24 themes, which were rearranged into four categories. Examples of the themes are as follows; development of super hard permanent magnets by crystallization process control of Nd-Fe-B amorphous alloys, as for structural control technology; research on high functional thin film sensors (PbLaTiO{sub 3}) using laser MOCVD, and research on ultra thin film by multi-ion-beam sputtering with ion/photo irradiation, as for thin film technology; R and D on highly ordered structure control technology in electrode surface compounded reaction fields, as for compounded fields; and, research on diagnostic technique for compounded reaction fields by laser-ionization method, as for supporting technologies. (NEDO)

  16. FY 1993 report on the results of the R and D of advanced function creation processing technology. Development of technology to create high efficiency power generation use members; 1993 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The paper described the FY 1993 results of the technology to create high efficiency power generation use members. A processing method was proposed in which to manifest magnetic characteristics up to the theoretical value level, crystallization of magnetic alloy amorphous was controlled and size/configuration of precipitated micro-fine crystals are made ideal. For the development of environmental purification use high functional catalysts, experiments were conducted on the heightening of purity of materials. Namely, by the two wavelength two stage excitation method using color laser, atomic beams of the material metal emitted by electronic beam evaporating source are photo-excited up near the ionization level. These are separated from the non-ionized components by electrostatic field application, and only the ionized atoms are vapor-deposited on substrate. The separation accuracy was good. Plasma excitation of raw gas was done independently for every component, and the multi-source excitation plasma CVD was proposed which is film-formed on the substrate of which the periphery was separately controlled. The synthesis method was considered of higher-order structure control high functional organic materials which are composed of electrode reaction/high grade photon/extreme magnetic field. Study was made of complex reaction field application film-forming/molecular orientation technology using a small test device. (NEDO)

  17. Basic investigation on promotion of joint implementation in fiscal 2000. Efficiency improvement project for district heat supplying plants in Dailian City in China; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Chugoku/Dailian shi chiiki netsu kyokyu plant kokoritsu kaizen project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Investigations and discussions have been given on energy saving possibilities at two medium-sized heat and power supplying plants in the city of Dailian in China. The project will improve the operation methods of the heat and power plants so that the energy cost can be minimized, and attempt to improve the boiler heat efficiency and save the energy by means of heat recovery and utilization. The draft modification plan for energy conservation has planned operation optimization for energy conservation, control of boiler operation under variable pressure, modification of the external boiler heat converter, use of inverters for the large capacity motors for boilers, and recovery of heat from the boiler blow-down water. In the analysis, models were structured from the operation data, and the effects of applying the energy saving measures were derived from simulation. As a result, the energy saving effect was found to be about 13,000 tons at the Chunhai plant and about 7,000 tons at the Pulandian plant annually (converted to oil). The reduction in greenhouse gas emission was found to be about 40,000 tons at the Chunhai plant and about 20,000 tons at the Pulandian plant annually. The number of years for investment payback is about 4.1 years at the Chunhai plant, and about 4.9 years at the Pulandian plant, wherein good profitability can be estimated. (NEDO)

  18. Research cooperation project in fiscal 2000. Research cooperation on developing high-efficiency mineral resource extracting and processing technology of environment harmonizing type; 2000 nendo kenkyu kyoryoku jigyo. Kankyo chowagata kokoritsu kobutsushigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A joint research has been carried out in the Republic of Kazakhstan on a technology to extract and recover efficiently the valuable metals (copper, gold, silver and others) contained in ore wastes in large quantity, with considerations given to the environment. This paper summarizes the achievements in fiscal 2000 being the last fiscal year. This joint research has performed researches on the processing technology and processes, and on the operation research by using a pilot plant, using low-grade ores in the Nikolayevska Mine and ore wastes from the Zhezkent Mineral Dressing Mill as the objects. As a result of the researches, the following matters were discovered: if the ore wastes are used as the starting materials in the copper recovering process using the chemical leaching process, the copper price of $1,800 per ton is the breakeven point; economic effect is enhanced by grinding the starting materials into finer particles, adding a zinc recovery process, and recovering gold by using cyanogens; and this pilot plant is pollution free, and easy in maintenance and control. These processes were concluded effective in reducing the efficient waste ore processing and environmental cost being the environmental problem in Kazakhstan. (NEDO)

  19. FY 1993 report on the results of the R and D of advanced function creation processing technology. Development of technology to create high efficiency power generation use members; 1993 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    The paper described the FY 1993 results of the technology to create high efficiency power generation use members. A processing method was proposed in which to manifest magnetic characteristics up to the theoretical value level, crystallization of magnetic alloy amorphous was controlled and size/configuration of precipitated micro-fine crystals are made ideal. For the development of environmental purification use high functional catalysts, experiments were conducted on the heightening of purity of materials. Namely, by the two wavelength two stage excitation method using color laser, atomic beams of the material metal emitted by electronic beam evaporating source are photo-excited up near the ionization level. These are separated from the non-ionized components by electrostatic field application, and only the ionized atoms are vapor-deposited on substrate. The separation accuracy was good. Plasma excitation of raw gas was done independently for every component, and the multi-source excitation plasma CVD was proposed which is film-formed on the substrate of which the periphery was separately controlled. The synthesis method was considered of higher-order structure control high functional organic materials which are composed of electrode reaction/high grade photon/extreme magnetic field. Study was made of complex reaction field application film-forming/molecular orientation technology using a small test device. (NEDO)

  20. Fiscal 1999 achievement report. Important regional technology research and development--Advanced machining technology for high-melting point metal based members (Development of creating technology for high-efficiency power generating members); 1999 nendo koyuten kinzokukei buzai no kodo kako gijutsu seika hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development is conducted concerning technologies of creating high-melting point metal based members for the purpose of enabling gas turbines to withstand still higher temperatures. In the research which deals mainly with Nb, solid solution state is enhanced, high-temperature strength and tenacity are improved by enhanced composition and diffusion, and surfaces are modified in terms of resistance to oxidation and corrosion by the technologies of multi-layer coating and slope-structured coating. In the designing and evaluation of high-strength Nb based solid solution alloys, alloys excellent in high-temperature strength and room-temperature tenacity are obtained, which contain 5-30at% Mo and 5-15at% W. In the designing and evaluation of Nb based composite materials, it is found that it strengthens the composition of Nb based enhanced solid solution alloys to add Si to Nb alloys for the precipitation of silicides in the Nb based solid solution alloy matrices. In the study of the creation technology for and evaluation of Nb based ultrahigh-temperature members, experiments are conducted with attention focused on the discharge plasma sintering method. In the development of technologies for providing oxidation resisting capability, studies are conducted about ion implantation and ion plating. (NEDO)

  1. `Technology for Advanced Treatment of High Melting Point Metal-Based Material,` local research and development of important technology for fiscal 1997. Development of materials creation technology for high efficiency power generator components; 1997 nendo juyo chiiki gijutsu kenkyu kaihatsu. `Koyuten kinzokukei buzai no kodo kako gijutsu` (kokoritsu hatsuden`yo buzai sosei gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Efforts are made for the creation of high melting point metal-base materials to replace the currently-used Ni-base superalloys for the turbine to withstand higher operating temperatures. The main efforts made in fiscal 1997 are outlined. As in fiscal 1996, Nb-base solution alloys, in which solution reinforcement elements such as Mo and W are alloyed, are manufactured by button arc melting and tested for mechanical properties and texture/characteristics. In the designing and evaluation for a strongest Nb-base composite material, Nb-base composite materials are manufactured by use of particle dispersion-strengthening attained by addition of intermetallic compounds or elements to contribute to the formation of oxides, carbides, or nitrides. Nb-base composite materials may also be manufactured by use of eutectic-strengthening attained by utilizing crystallization in the process of coagulation. The resultant Nb-base composite materials are evaluated for their dynamic characteristics at high temperatures. In the development and evaluation of technologies for creating Nb-base materials for high-temperature components, larger specimens as heavy as several kg are tested in line with small specimens for basic studies, and the results are utilized for alloy designing for high-temperature materials. 50 refs., 97 figs., 15 tabs.

  2. FY 2000 report on the results of the supplementary project for the development of energy utilization rationalization technology. Leading study for the development of high efficiency thermoelectric converter; 2000 nendo energy shiyo gorika gijutsu kaihatsu hojo jigyo seika hokokusho. Kokoritsu netsuden henkan soshi kaihatsu sendo kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    For the purpose of energy conservation and environmental protection by effective utilization of unused waste heat, the R and D of thermoelectric conversion technology were conducted, and the FY 2000 results were summed up. In the investigative study of thermoelectric converting materials, evaluation was made of the materials having a possibility of achieving the target with the element efficiency of 6% and the assumed use temperature domain of 120-330 degrees C. The result of the study indicated that the number of new materials which were made public was increasing, but there were no materials that have evidently practical applicability. In the investigative study of element manufacturing technology, trial manufacture of element was made in which the investigative results were integrated into the existing 50W element manufacturing technology, and a target of 70W was achieved. In the investigative study of the thermoelectric conversion system for industrial and commercial/residential use, field survey and questionnaire survey were conducted for three fields of iron works, chemical plant and garbage disposal plant. As a result, it was found that there was a large amount of waste heat. By the study of the system conceptional design, it was found out that the output of 40-50kW can be obtained in the system structure suitable for the source of waste heat of iron works, etc. (NEDO)

  3. FY 1992 Report on results of the research and development of the technologies for forming composite materials. Development of the technologies for creating parts for high-efficiency power generation systems; 1992 nendo fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    This project is aimed at development of the technologies for producing ceramic- and metal-based composite materials, and also technologies for superplastic processing by utilizing the phenomenon of superplasticity. The methods studied for development of the ceramic-based composites include casting and powder-utilizing forming at low temperature, and melt forming at high temperature. Those for the metal-based composites include melting at normal and high pressure, powder metallurgy type mechanical alloying and alkoxide methods. The composites studied for development of the superplastic processing are the whisker- and particle-reinforced ones. The composite reinforced with silicon nitride/SiC whiskers is found to be electrophoretically cast to have a bending strength of 497MPa at 1,250 degrees C. The parts of simple shape, e.g., rod and disk, having the target strength are produced by isostatically pressing at normal temperature and high pressure (CIP) and subsequently firing the granules, produced by spray drying the TiC particle/alumina-based slurry. (NEDO)

  4. FY 1992 report on the results of the R and D of advanced function creation processing technology. Development of technology to create high efficiency power generation use members; 1992 nendo senshin kino soshutsu kako gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    The paper described the FY 1992 results of the technology to create high efficiency power generation use members. To enhance characteristics of super-high property permanent magnet up to the theoretical level, the development was proposed of a technology to control the size/configuration of micro crystal phase in association with the crystallization of alloy amorphous. For the development of environmental purification use high functional catalysts, a refining method using laser excitation was studied. The observation was also made of molecular adsorption on the Pd thin film catalyst prepared by RF sputtering. The multi-source excitation plasma CVD was proposed which was film-formed by exciting plasma as raw gas independently for each component and supplying it to the substrate of which the periphery was separately controlled. The paper also described the development of technology for ion/light combined assist ultra-thin film production for development of gas turbine combustion sensor. The study was also made of the synthesis of higher-order structure controlled high functional organic materials using the electrode interface combined field which is composed of electrode reaction/high grade photon/extreme magnetic field. In the development of the higher-order structure control technology using the photon combined reaction field, studies were made of the photo reaction film formation technology, the basic film formation technology in the combined reaction field, and the molecular orientation technology. (NEDO)

  5. FY 1998 report on the results of the R and D on the venture promotion type regional consortium small-/medium-size enterprise creation base type. Research and development of energy-saving and high-efficient drying system of high water content organic substances; 1998 nendo kogansui yukibutsu no shoenegata kokoritsu kanso system no kenkyu kaihatsu seika hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This project is implemented to save energy for drying bio-products (biological object organic substances), such as laver, fish and shellfish, shiitake mushroom and tobacco leaves, without deteriorating their flavor, taste, color and luster. In particular, it is aimed at development of high-efficiency drying devices friendly to these products, e.g., laver, and in harmony with energy-saving environments through creation of novel drying chambers and peripheral facilities around the heat exchanger, and elucidation of the drying processes of the organic substances. These devices can of course contribute to energy saving and environmental protection, and, at the same time, bring about the merit of easily controlling the three elements of the drying conditions precisely for the process of drying a specific organic substance. Moreover, the R and D project will help establish know-hows that allow the drying devices to diffuse into various areas for specific drying environments characteristic of region and product. The FY 1998 R and D efforts include (1) elucidation of the stepwise process for drying each product, (2) development of the algorithm for thermohydraulic elucidation of the system and drying process, (3) development of drying chambers for drying systems, and designing and fabrication of the optimum chamber shapes, and (4) evaluation of the energy flows and mass balances in the drying system. (NEDO)

  6. Fiscal 1992 survey report of R and D on new forming technology of composite material. Development of innovative technology for producing members for high efficiency power generation; 1992 nendo fukugo zairyo seikei gijutsu chosa hokokusho. Fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu (kokoritsu hatsuden'yo buzai soseigijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    Composite forming technology is being developed which is intended to manifest superplasticity phenomenon of ceramic matrix and metallic matrix composite materials; also being developed is an effective efficient superplastic processing technology which utilizes this composite forming technology. The related technologies were investigated comprehensively systematically with the purpose of promoting the development. First, an overview was given in the present state and problems of ceramic matrix/metallic matrix composite technologies and in the forefront of the superplasticity research of ceramic matrix materials, and then, the related technologies of these composite materials were pigeonholed under the following items: 1. assesment/strength/dynamic properties, 2. composite process and property, 3. composite forming process, 4. superplasticity, 5. process and superplasticity, and 6. others. The titles of the rearranged summary documents are, for example, surface modification and casting of SiC platelets in Al{sub 2}O{sub 3} composites, deformation of Al{sub 2}O{sub 3}/TiC composites at elevated temperatures, superplastic bulging of fine-grained zirconia, forging of short alumina fiber reinforced aluminum alloy, and on superplasticity in silicon carbide reinforced aluminum composites. (NEDO)

  7. Fiscal 1992 achievement report on next-generation industrial structure technology. Research and development of advanced materials for extreme environments (Development of high efficiency power generation component creation technology); 1992 nendo chotaikankyosei senshin zairyo no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden'yo buzai no sosei gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    Studies were made to develop technologies for creating carbon based advanced composite materials for use under extreme environments, and a comprehensive technology survey was conducted in this connection. Studied in the comprehensive survey were coordination between various technology developing activities, research on trends of relevant technologies, and technical tasks to discharge for the development of materials usable under extreme environments. In addition, interim evaluation was performed. Carried out in the development of C/C (carbon/carbon) composite materials using coal pitch derived fibers were carbon matrix optimization and studies of rupture mechanism, and the fabrication of specimens by compounding and molding under the hot press method and HIP (hot isostatic process). Carried out in the development of C/C composite materials using PAN (polyacrylonitrile) based carbon fibers were studies of rupture mechanism and the like, fabrication of specimens by compounding and molding, and performance enhancement under the high pressure impregnation carbonization method and the like. Oxidation resistant coatings were fabricated and tested for performance, and preliminary experiments were conducted toward the development of a novel coating technology. (NEDO)

  8. Report on achievements in fiscal 1999 on research and development of an intellectual base creating and utilizing technology. Research and development of a high-efficiency human body measuring device; 1999 nendo chiteki kiban sosei riyo gijutsu kenkyu kaihatsu seika hokokusho. Kokoritsu jintai keisokuki no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes the achievements in fiscal 1998 on developing a high-efficiency human body measuring device. Object building with high compatibility is requested in recent years, and a high-precision and high-efficiency measuring device for three-dimensional human body shape data is demanded. The ultimate target for the device is high-precision measurement of about 1 mm in about one second which is the time for human being capable of staying immovable. In association with proliferation of product designing by using a computer, the needs for data handling on computers are increasing sharply in industries. Proposals have been made by ISO and CEN on the standards for morphological characteristics of human being, inducing progress in international standardization of human body size and shape data. Structuring a database is also planned on three-dimensional shape data mainly in the U.S.A. The Human Life Engineering Research Center is studying development of a measuring device to measure human body types and sizes at high speed and accuracy. The device combines three-dimensional measurement by using an optical method with high-performance computerized image processing. The measuring device is supposed to be capable of outputting the measurement results as the size and three-dimensional shape data, so that the results can be applied to product designing quickly. (NEDO)

  9. Report on a project to support promotion of forming an environmentally friendly energy community. Survey on an environmentally friendly community business by means of high-efficiency wastes power generation system in the Toyota-Kamo wide area; Kankyo chowagata energy community keisei sokushin hojo jigyo chosa hokokusho. Toyota Kamo koikiken kokoritsu haikibutsu hatsuden kankyo chowagata energy community jigyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Taking the Toyota-Kamo wide area as the object, wastes power generation is positioned over the society system as worked on by administrations and operators integrally to incinerate mixedly those incineratable materials such as plastics among general and industrial combustible wastes for high-efficiency generation of power, which is supplied to electric utility operators as surplus power. Discussions were given on the business feasibility and the effectiveness as a society system. In this area, the mixed model B plan (dealing with general wastes plus industrial wastes) was evaluated as an effective plan as the society system. This is because the plan has effect to incinerate, melt and generate power from industrial wastes which have been used for land-fill, effect of improving the power generation efficiency, and effectiveness of mixed treatment with general wastes. The plan A in which general wastes are made into RDF, then incinerated mixedly with industrial wastes for power generation was evaluated to have high reliability potential of power supply and to be an effective plan as a society system, if effect can be expected to reduce transportation energy as a result of making the system large enough and turning wastes into RDF. (NEDO)

  10. FY 1999 research cooperation project. Research cooperation in development of technology to extract/treat mineral resources in environmental harmony and high-efficiently; 1999 nendo kankyo chowagata kokoritsu kobutsu shigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This project is aimed at effectively using non-ferrous metal resource in Kazakhstan Republic and at conducting a joint development of the environment-friendly and efficient technology to extract/collect valuable metals (copper, gold, silver, rare metal, etc.) including in quantity in the slag generated with the mine operation in Kazakhstan. For the purpose of collecting valuable metals from slag, etc., the project is to develop the technology to collect valuable metals in saving energy and in low environmental loads by adopting the wet treatment process and to carry out the field survey on the existence of slag, etc. and the research on minerals. As the field research/domestic research, various element technologies are also to be carried out such as leaching, solvent extraction, electrolyte sampling, and waste water treatment. Based on the R and D of the element technology, a pilot plant is designed/fabricated and installed at the site in Kazakhstan. Then, the operation is studied and analyzed to make a technically/economically comprehensive evaluation. In this fiscal year, the field survey, research on the wet treatment, and test on the waste water treatment are conducted. Facilities of a pilot plant were transported to the site. (NEDO)

  11. FY 1998 annual summary report on manipulation of atomic and molecular extremes. Development of technologies for high-efficiency analysis/manipulation of DNA and the like; 1998 nendo genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho. DNA nado kokoritsu kaiseki sosa gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The objectives are set to establish the techniques for observation/manipulation of atoms and molecules, as the common basic techniques for various industrial areas, e.g., new materials, electronics, biotechnology and chemical. Development of atomic field and scanning tunneling microscopes working under extreme conditions has been pursued, in order to manipulate complex systems, such as living body. For identification of molecular species, laser-excited fluorescence is combined with scanning mechanical probing to further refine the single molecule detection/identification techniques, and the objectives are set to develop a new method for evaluating molecules in a living body using a scanning probe microscope, and also to develop a novel scanning probe microscope for molecules in a living body. The other efforts were directed to R and D of the techniques for observing structures of organic molecules and the like through the measurements of adsorption process of organic molecules and clusters on semiconductor substrates and their surface reactions, and precision measurements of vibrational conditions of adsorbed molecular species reacting in the solid-liquid interfaces by high-sensitivity Raman spectroscopy to elucidate the catalysis mechanisms at the molecular level. (NEDO)

  12. Fiscal 1994 report on results of R and D on new forming technology of composite materials. Development of innovative technology for producing members for high efficiency power generation; 1994 nendo fukugo zairyo shinseikei gijutsu no kenkyu kaihatsu seika hokokusho. Kokoritsu hatsuden buzai sosei gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    Activities were conducted in the three areas of (1) R and D on ceramic matrix composite forming technology, (2) R and D on metallic matrix composite forming technology, and (3) comprehensive investigation and adjustment, for the purpose of developing materials that manifest superplasticity among ceramic and metallic matrix composites as well as developing the forming and fabrication technology and also of improving productivity by simplifying the fabrication processes. In (1), upon discovering that the superplastic properties of zirconia (3Y-ZrO{sub 2}) sold in the market is affected by the grain size and impurities (Al{sub 2}O{sub 3}) of the material, a zirconia was developed in which a trace of Al{sub 2}O{sub 3} and SiO{sub 2} were added, with a method detected capable of the fabrication through a low deforming stress. In (2), development was carried forward for a new high specific strength high-temperature material applicable to aircraft engines for example, as well as its forming and fabrication technology, by making a composite between metals and between metal and ceramics by a mechanical alloying (MA) method. Metalcarbide, nitride and oxide made by the MA method were sintered by hot press or the like, and a sintered material was thereby obtained that was superplastic and capable of the near net-shape forming. (NEDO)

  13. FY 2000 report on the basic survey to promote the joint implementation. Potential survey of the greenhouse effect gas reduction by high-efficient utilization of the oil residue in Bataan Refinery in the Philippines; 2000 nendo kyodo jisshi nado suishin kiso chosa hokokusho. Philippines koku Bataan seiyusho ni okeru sekiyu zansa kokoritsu riyo ni yoru onshitsu koka gas sakugen kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of reducing the CO2 emitted from electricity/vapor supply facilities of Bataan Refinery in the Philippines, study was conducted of optimum energy supply facilities considering the effective use of the oil residue and future reinforcement of the refinery. Concerning the high-pressure/high-temperature condensing extraction boiler/turbine cogeneration, gas turbine cogeneration and low speed diesel engine cogeneration, comparative study was carried out in terms of thermal efficiency, reliability/preservation, environmental acceptability, effectiveness of measures for the future excessive oil residue, etc. As a result, the study was concluded as follows: the electric power consumption will markedly increase in the future; however, in the light of the situation of the refinery where the vapor demand will not increase, it is the most suitable to use low speed diesel engine cogeneration facilities as on-site power generation facilities which can burn the excessively increasing oil residue as direct fuel. The CO2 reduction effect estimated from the project on the present scale was 132,880 t-CO2/y, and the energy conservation effect estimated was 50,861 toe/y. (NEDO)

  14. Report on achievements in fiscal 1999. Technology for a closed type high-efficiency gas turbine handling recovery of carbon dioxide (Research and development in the first term); 1999 nendo nisanka tanso kaishu taio closed gata kokoritsu gas turbine gijutsu daiikki kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development has been made on a gas turbine that can separate and recover carbon dioxide without discharging nitrogen oxides by means of oxygen combustion of natural gas (methane). This paper summarizes the achievements in fiscal 1999. The system discussions included those on accuracy of a performance analyzing program, sensitivity analysis, and a possibility of constructing a closed verification device in case of using the existing gas turbines. In developing the combustion control technology, design, trial fabrication, and combustion tests were carried out on combustion nozzles. As a result, it was discovered that achieving the combustion efficiency of 98% or higher is possible as the development target for the time being. In developing the turbine blade cooling technology, two-dimensional analysis was performed on heat fluidity between blades by using the low Reynolds k-{epsilon} method, wherein relatively good agreement with measurement results was obtained. In developing major auxiliary devices, a high-pressure compressor was designed, and candidate materials for a condenser and a heat exchanger were tested. In developing ultra high temperature materials, an oxidation test was performed on the undercoat for TBC, and a steam oxidation test on TMS-75. (NEDO)

  15. Development of high efficient L-lactate fermentation and P(3HB) biosynthesis for [Lactate Industry], the new technology for post-petrochemistry; Posto petoro kemisutori toshiteno Lactate Industry wo jitsugen surutameno kosoku kokoritsu L-nyusan hakko to P(3HB) hakko seisan no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Ishizaki, Ayaaki; Kobayashi, Genta; Vonktaveesuk, P.; Tsuge, Takeharu; Tanaka, Kenji [Kyushu University, Fukuoka (Japan). Faculty of Agriculture

    1999-03-10

    We have developed a high efficiency L-lactate fermentation process employing the homofermentative lactic acid bacterium, Lactococcus lactis IO-1 with a pH-dependent substrate feed system in order to consume the substrate completely and maintain high activity of cell growth, production, and substrate consumption. Furthermore a pH-dependent substrate feed system was combined with turbidity control consisting of a laser probe and micro filter module for cell-recycling. With this system, we achieve a high efficiency L-lactate continuous culture. We are able to construct high efficiency bioconversion systems from xylose to P(3HB) via L-lactate and other organic acids because Lactococcus lactis IO-1 can utilize not only glucose but also xylose as a carbon source. Thus, we have developed a new substrate feed system which is able to automatically control substrate concentration in a broth. A new batch fermentative system for production of biodegradable plastic material, poly hydroxybutyrate [P(3HB)] from culture broth of Lactococcus lactis IO-1 is vealized. (author)

  16. Development of high-speed and high-efficient L-lactic acid fermentation and P (3HB) fermentative production for realizing Lactate Industry as Post petrochemistry; Posuto petorokemisutori to shiteno Lactate Industry wo jitsugensuru tameno kosoku kokoritsu L-nyusan kakko to P(3HB) kakko seisan no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Ishizaki, Fumiaki; Kobayashi, Genta; Vonktaveesuk, P.; Tsuge, Takeharu; Tanaka, Kenji [Kyushu University, Fukuoka (Japan)

    1999-04-05

    We are streptococci For the purpose of maintaining thing, it is high in the culture of Lactococcus lactis IO-1 in respect of perfect use of the substrate and metabolism activity of bacterial cell, and it pHs pH Substrate feed control method (pH-dependent substrate feed system) as an index was developed. In addition, advanced and integrated continuous culture system which enabled stabilized culture system and high lactic acid production speed was constructed by using furnace concentrator and on-line laser turbidity controller. And, Lactococcus lactis IO-1 By going through the organic acid such as the lactic acid from the xylose, it seems to be possible to carry out bio conversion of which it is efficient, since it is also very much excellent in the utilization-ness of the xylose which is a major component of tree biomass of the glucose otherwise. Then, culture medium supply method which enabled new batch culture system and substrate concentration automatic control for making this lactic bacteria and fermented milk acid liquid produced using culture system and organic acid liquid to be a substrate, and for producing polyhydroxy butyric acid [P (3HB)] which is the biodegradable plastic material by Alcaligenes eutrophus at high speed high-density was developed. (translated by NEDO)

  17. Fiscal 2000 survey report. High-efficiency energy system introduction promotion project for houses and structures - Houses (Technical classification tables prepared by analysis of proposed systems, and comments on the same); 2000 nendo jutaku kenchikubutsu kokoritsu energy system donyu sokushin jigyo (jutaku ni kakawaru mono) teian system no bunseki ni yoru gijutsu bunruihyo oyobi dokaisetsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As an energy conservation promotion measure, a project is under development for introducing and subsidizing high-efficiency energy systems and for letting their effect known publicly and widely. The number of proposed energy systems has increased greatly and technical divisions to follow in classifying them have become vague, from which problems are now arising over the execution of follow-up checks and the maintenance of fair treatment. In the effort to solve this problem, 376 propositions are analyzed and classified, a technical classification method is proposed, and an instruction manual on the method is compiled. The classification involves (1) proposed classification, (2) variation, (3) energy reduction rate, and (4) tentatively calculated cost. Item (1) deals with the basic classification (air-conditioning, ventilation, and hot water supply, and, to be considered in combination with them, options which are cooking, illumination, and others) and, item (2) covers eight items such as new/old construction, structure, and structural frame. In Chapter 1 of the report, the 376 propositions are put in order according to common classification items and an original classification table is prepared. In Chapter 2, the goals are clarified and the classification principles are defined. In Chapter 3, the classification is checked for its validity and some realistic ways of grouping are described. In Chapter 4, a classification implementation flow chart is shown. (NEDO)

  18. Fiscal 1999 project for research and development of industrial and scientific technologies. Report on the achievements on the 'research and development of an ultimate atom and molecule manipulation technology' (Development of a technology to analyze and manipulate DNAs at high efficiency); 1999 nendo genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho. DNA nado kokoritsu kaiseki sosa gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In the 'research and development of an ultimate atom and molecule manipulation technology', research has been made on an organic atom and molecule identification and manipulation technology and a dynamic organic molecule simulation technology. This paper summarizes the achievements in fiscal 1999. In the magnetic force controlling AFM for the force spectroscopy aimed at non-destructive atom and molecule identification, a prototype cantilever was fabricated that can excite and detect displacement in lateral direction and is suitable for friction measurement. The SrO surface and TiO2 surface of SrTiO{sub 3}. A carbon nano-tube was employed as a probe. In addition, the molecule inserting SAM technology was used to have developed a technology to measure electric conductivity inside and between molecules. With an aim at realizing a high-speed DNA base arrangement analyzing method, research is being performed upon noticing the single molecule method based on the light measuring method using the single molecule imaging as the base and the scanning probe microscope method. For the dynamic organic molecule simulation technology, theoretical analysis was advanced on synthesis of methanol on copper surface. (NEDO)

  19. Summarized report on research cooperation promotion project in fiscal 2000. Research cooperation on developing high-efficiency mineral resource extracting and processing technology of environment harmonizing type; 2000 nendo kenkyu kyoryoku suishin jigyo sokatsu hokokusho. Kankyo chowagata kokoritsu kobutsushigen chushutsu shori gijutsu no kaihatsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    A joint research with the Republic of Kazakhstan has been carried out on developing a technology to extract and recover efficiently the valuable metals (copper, gold, silver and others) contained in ore wastes in large quantity produced in association with mine operation, with considerations given to the environment. This paper summarizes the achievements in fiscal 2000. The joint research has performed site survey for existence of ore wastes in the Republic of Kazakhstan, domestic research for discussing the disposal systems, design, fabrication, installation, adjustment and operation of a pilot plant. Process researches included ore flotation test, leaching test on Zhezkent ore wastes in chemical leaching and low-grade Nikolayevska ores, Cu leaching acceleration effect in bacteria leaching, utilization of activated carbon, fundamental test on solvent extraction, reverse extraction test, test using iron oxidizing bacteria in waste water treatment, Fe{sup 2}+ oxidation in waste water due to waste water bacteria concentrated by diatomaceous earth, Au and Ag leaching test, and column leaching test. This paper summarizes the results thereof. (NEDO)

  20. FY 2001 report on the results of the survey of the formation promotion subsidy project on the environmentally friendly type energy community. Survey of the commercialization of high efficiency power generation using fuel of waste such as waste construction materials; 2001 nendo kankyo chowa gata energy komyuniti keisei sokushin hojo jigyo. Kensetsu haizai tou haikibutsu nenryo ni yoru kokoritsu hatsuden no jigyosei chosa chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    The paper studied a system for power generation and heat utilization using wood chips such as waste construction materials, used paper inappropriate for recycling and plastic refuse from neighboring local governments as fuel and assessed a potentiality of the commercialization. As to the system, the following were conducted: selection of the optimum combustor in the waste power generation, survey of the state of corrosion of boiler tube in the steam conditions and waste properties, selection of the optimum quality of boiler materials, etc. In the assessment of a potentiality of the commercialization, the commercialization was studied as in-house power generation/heat utilization business with a power generation scale of 9,950kW and a steam supply scale of 31.5t/h. As a result of the study, the energy conservation effect was found to be expected as follows: reduction of 33,000kL/y crude oil equivalent and reduction of 16,000t-CO2/y emission. As a result of studying the economical efficiency of business, the unit price of wood chip purchase and the unit price of waste plastic treatment which are required to recover the difference of the initial investment within 5 years were greatly different from the level as an aim. For the realization as business, a subsidy of 15% and more cost reduction were requested. (NEDO)

  1. FY 2000 report on the results of development of technology for commercializing high-efficiency fuel cell systems. Development of technology for commercializing high-efficiency fuel cell systems (Development of technology for effective utilization of power produced by polymer electrolyte fuel cell systems); 2000 nendo kokoritsu nenryo denchi system jitsuyoka gijutsu kaihatsu seika hokokusho. Kotai kobunshigata nenryo denchi no shutsuryoku yuko riyo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This project is aimed at development of technologies for effective utilization of power produced by polymer electrolyte fuel cell (PEFC) systems and waste heat, to spread cogeneration systems incorporating PEFC systems for residential purposes. Described herein are the FY 2000 results. The program for high-efficiency peripherals for residential PFEC systems attempts use of GaN-FET as the semiconductor device of wide band gap and high breakdown voltage to realize conversion efficiency over 90% by improving inverter efficiency. Two types of the prototype heat recovery systems are developed for the PEFC, one incorporating a latent heat cooling system and the other a water cooling system, to improve heat recovery efficiency and increase heat recovery temperature. The program for technology to fit PEFC output to energy demand develops hot water supply systems provided with a hot water storage function for stable supply of hot water irrespective of the heat recovery conditions, and also with a back-up function with burners. The program also develops the PEFC system of fine load following characteristics, for which pure hydrogen is used as the fuel to allow the system to instantaneously follow fluctuating loads. The program for high-efficiency partial load operation technology studies a 1kW-class residential PEFC cogeneration system incorporating a power storage device for high-efficiency operation at partial loads, where the former operates in a high output mode while the latter absorbs fluctuating loads. (NEDO)

  2. Fiscal 2000 achievement report. Research and development of fast-acting innovative energy-environment technology (Development of fast-acting high-efficiency solar cell technology - Development of high-quality ingot manufacturing technology); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko itaku kenkyu gyomu seika hokokusho. Sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu (Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu - Kohinshitsu ingot seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was conducted of a technology for manufacturing an ultrathin polycrystalline silicon solar cell capable of efficiency enhancement and cost reduction earlier than the types of polycrystalline solar cells now available on the market. In this fiscal year, a silicon melt/solidification experimenting apparatus was built for manufacturing high-quality silicon ingots. Using an apparatus with its performance similar to the newly built one, a preliminary experiment was conducted involving high-purity silicon ingot manufacturing. In the experiment, boron was added to 75 kg of silicon for semiconductor devices so that its resistivity may be 0.5 ohm-cm. The silicon was melted in a quartz mold, and then subjected to unidirectional coagulation at 0.13 mm/min that started at the bottom to proceed upward. The result was a silicon ingot 44 cm times 44 cm times 17 cm (height). The ingot thus obtained exhibited 0.4-0.8 ohm-cm in resistivity distribution. Solar cells produced from the ingot showed a conversion rate of 16.9%. (NEDO)

  3. Report on achievements in fiscal 1999 on research and development of immediately effective and innovative energy environment technology. Part 1. Development of immediately effective and high-efficiency solar cells, and development of technology to slice and manufacture thin-type large-area polycrystalline substrates; 1999 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu seika hokokusho. Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu (usugata daimenseki takessho kiban slice seizo gijutsu kaihatsu 1)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective of decreasing silicon usage quantity for the purpose of reducing the solar cell production cost, development is being performed on an ingot cutting technology to cut a silicon ingot to Kerf loss of 150 {mu} m and thickness of 150 {mu} m, and in which the produced wafers can withstand the cell making. Investigations revealed that a wire saw is suitable as the cutting system, and the wire used must have a diameter of less than 120 {mu} m, and a strength of more than 3850 N/mm{sup 2}. A prototype wire was fabricated, whose diameter is 120 {mu} m, and in which the strength is distributed between 3870 and 4110 N/mm{sup 2}. It was found possible that a wire of 160 {mu} m can be used to slice an ingot having a cross section surface of 150 mm square and a length of 300 mm into a slice having a Kerf loss of 200 {mu} m and a thickness of 180 {mu} m. This wafer had the in-plane distribution of the substrate thickness at {+-} 12.5 {mu}, swell of 120 {mu} at maximum, and surface roughness of 5 {mu}. Making ten of these wafers into a cell resulted in a yield of 60%. Assignments are the clarification of the properties of the cutting wire, the preparation of a thin wire with homogeneous quality, and the establishment of a technology to cut Kerf loss of 150 {mu} and substrate thickness of 150 {mu}. (NEDO)

  4. FY 2000 Report on the results of research and development of the important regional technologies. Development of high-order processing of high-melting metal-based parts (Development of technologies for creating parts for high-efficiency power production); 2000 nendo juyo chiiki gijutsu kenkyu kaihatsu seika hokokusho. Koyuten kinzokukei buzai no kodo kako gijutsu (kokoritsu hatsuden'yo buzai sosei gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 2000 results of the research and development of heat-resistant materials, aimed at increasing operating temperature of gas turbines not equipped with a cooling system and thereby further improving their thermal efficiency. The program for design/evaluation of high-strength, Nb-based solid solution alloys develops the Nb-based alloy reinforced with a solid solution comprising 5 to 30% of Mo and 5 to 15% of W, all by atom, simultaneously dissolved. The program for design/evaluation of high-strength, Nb-based composite materials confirms effectiveness of incorporating Si in a Nb alloy and separating silicide in the Nb-based solid solution alloy matrix as the combined mechanism of reinforcing the alloy. The program for creation/evaluation of Nb-based parts which withstand superhigh temperature finds that the discharge plasma method gives the structure, in a very short time, almost on a level with that given by the solution solidification method. The program for oxidation resistance improving technologies develops the electrochemical process for forming the oxidation-resistant coating film. The stable oxidation-resistant performance is observed in the preliminary test, because the sample loses no weight when exposed to around 1000 degrees C in air for 10 hours. (NEDO)

  5. Fiscal 1997 R an D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules (high-efficiency and analysis and manipulation technology for DNA); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (DNA nado kokoritsu kaiseki sosa gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). Through the observation of super spiral DNA fixed on a spermin or spermidine treated mica substrate by AFM (atomic force microscope), fixation of DNA without any deformation in solution was clarified, and visualization of the spiral structure of DNA were successfully achieved. Manipulation of Xe atoms adsorbed on an Si(111) surface was certainly possible by using STM (scanning tunneling microscope)/atom probe equipment. A nucleation mechanism in crystal growth was studied for various organic source-molecules/GaAs(001) surface systems, and formation of high-density nuclei on the GaAs surface was achieved by accelerating the translational energy of Ga material molecules up to 6eV or more. Ziegler- Natta catalysis important for industrial polymerization of olefin molecules was precisely analyzed by first-principle dynamic simulation. A large-scale simulation of zeolite catalyst is also in promotion for methanol to gasoline conversion. 51 refs., 87 figs., 7 tabs.

  6. FY 2000 report on the results of the development of transportation use and residential/commercial use high efficiency energy system technology. R and D of polymer electrolyte cells (Research on ion exchange membranes for commercialization of highly durable cells); 2000 nendo unyu minsei you kokoritsu energy system gijutsu kaihatsu seika hokokusho. Kotai kobunshigata nenryo denchi no kenkyu kaihatsu (Kotaikyusei denchi jitsuyoka no tame no ion kokanmaku ni kansuru kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As to ion exchange membranes for fuel cells, the R and D were made with the aim of clarifying the characteristics of the membrane required to realize highly durable modules and of demonstrating durability of membrane, and the FY 2000 results were reported. Concerning the low ion exchange capacity thin membrane, the following were confirmed: in perfluorosulfonic acid with ion exchange capacity of 0.84-1.0, the lower the ion exchange capacity is, the greater characteristics of mechanical strength are improved; the optimization of membrane thickness makes the design which satisfies cell characteristics and mechanical strength characteristics possible. In the durability test by medium-/long-term continued operation using each of small unit cell and large unit cell, the results of the stable operation of 5,000 hours using S1102 and S1201Q membranes were obtained. About effects of methanol, changes were observed in creep characteristics and piercing strength in the test on the environmental cycle at -40 degrees C to 80 degrees C. The membrane of low ion exchange capacity kept high elastic modulus even after the treatment at 120 degrees C, which indicated its usability for the higher temperature operation. (NEDO)

  7. Fiscal 2000 project of inviting proposals for international joint research - invitation for international proposal (Power generation No.2). Achievement report on development of high-efficiency low-temperature power generation device using SOFC containing yttria-doped ceria layer; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (hatsuden No.2). Yttria gan'yu ceria so wo yusuru SOFC kokoritsu teion sadogata hatsuden sochi no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts continue to develop a solid oxide fuel cell (SOFC) capable of consuming methane, propane, and the like, as fuel directly and of operation at 650 degrees C or lower. The efforts in concrete terms involve the development of an anode material, an electrolyte, and a cathode material not to suffer carbon precipitation and the evaluation of power generation performance of a hydrocarbon fueled single cell. Activities are conducted in the five domains of (1) the fabrication of an SOFC single cell and a preliminary study, (2) evaluation of solid electrolyte thermal stability using X-ray diffraction, (3) anodic carbon precipitation test and single cell performance test, (4) survey of technical trends overseas, and (5) the goal and self-management. In domain (1), technologies are developed to form thin film anodes of Ni-GDC (gadolinium-doped ceria), Cu-GDC, Ni-YSZ (yttria-stabilized zirconia), and the like, for which the ultrasonic spray method and slurry coat method are used. In the study of cell manufacturing, the anode support method and cathode support method are investigated. The anode support method is used to fabricate a thin film, a thin YSZ film is successfully fabricated for typical Ni-YSZ. (NEDO)

  8. Fiscal 1993 international research cooperation project. Feasibility study of finding out the seeds of international joint research (technology for environmental preservation using biotechnology, technology for effective use unused hydrocarbon resource, technology of solid electrolyte fuel cells for high-efficient electric vehicles); 1993 nendo kokusai kenkyu kyoryoku jigyo. Kokusai kyodo kenkyu seeds hakkutsu no tame no FS chosa (biotechnology ni yoru kankyo taisaku gijutsu, miriyo tanka suiso shigen no yuko riyo gijutsu, kokoritsu denki jidosha no kotai denkaishitsu nenryo denchi gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    This project is aimed at internationally cooperating in the R and D of industrial technology and improving industrial technology of Japan. For it, the following three technologies were investigated: 1) environmental preservation technology using biotechnology, 2) technology for effective use of unused hydrocarbon resource, 3) solid electrolyte fuel cell (SOFC) technology for high-efficient electric vehicles. In 1), bio-remediation is a choice as the result of trially using technologies for remediation of the environment polluted by pollutant, but it is not a technically completed one, but one which will be improved by trial and error. By the application of gene engineering, the use of gene recombination enables wide spread of decomposition genes. In 2), technical subjects were studied such as superheavy distillate, oil shale, coalhead methane and methane hydrate. In 3), designed were cylinder type and planar type SOFC of 850degC operation and 10kW output. Accumulation and weight of a total SOFC system are 81 liters and 100 kg in cylinder type and 136 liters and 200 kg in planar type. The vehicle can be equipped with the SOFC. 171 refs., 72 figs., 54 tabs.

  9. Report on achievements in fiscal 1999. Research and development of immediately effective and innovative energy environment technology (Development of immediately effective and high-efficiency solar cell technology, development of high-quality ingot manufacturing technology, and development of high-efficiency cell making technology); 1999 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu seika hokokusho. Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu (kohinshitsu ingot seizo gijutsu kaihatsu / kohinshitsu cell ka gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development has been made on improving quality of ingots for substrates, manufacturing high-quality thin type substrates, and making high-efficiency cells. This paper summarizes the achievements in fiscal 1999. In developing the high-quality ingot manufacturing technology, discussions were given on a method for assessing impurities and crystal defects by using the total reflection scattering type infrared tomography, and on the optimal solidifying and cooling conditions during the ingot manufacturing by using simulation calculation for solidification. As a result of analyses and discussions, such findings were found effective that the ingot should be solidified through making the solid-liquid interface shape flat, and the temperature falling rate in an ingot should be maintained constant. In developing the high-efficiency cell making technology, discussions were given on the optimal construction based on a simulation that assumes the light sealing structure using the RIE method, and on the optimal construction of polycrystalline silicon solar cells by using a device simulator (PCID). The important factors in achieving a conversion efficiency of 20% are the light sealing structure, surface passivation, and substrate thickness. (NEDO)

  10. FY 1999 Report on results of development of high-efficiency energy system technologies for transportation and domestic use. R and D of polymer electrolyte fuel cells, power system technologies, and several kW class domestic power systems operating at normal pressure; 1999 nendo un'yu minseiyo kokoritsu energy system gijutsu kaihatsu, kotai kobunshigata nenryo denchi no kenkyu kaihatsu, hatsuden system gijutsu kaihatsu, joatsu sadogata su kW kyu kateiyo dengen system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Described herein are the FY 1999 results of the research and development project aimed at development of fuel cell systems for power source systems suitable for domestic use. The programs for development of fuel cell body include improvement of the anode forming method for increasing its CO tolerance, enhancing cell performance at 0.5mg-metal/cm{sup 2} as the catalyst quantity to a level almost comparable to that obtainable at 0.9mg-metal/cm{sup 2}. The programs for development of the fuel supply system include studies on endurance of the elements, e.g., starting-up/shutting-down of the Ru/Al{sub 2}O{sub 3} catalyst, using a microreactor, confirming that it is serviceable for at least 1,000 hours. The natural gas reformer is developed and operated, on a trial basis, achieving stable supply of steam and fuel, and thermal efficiency of 82.7%. The operation researches include development and operation of a 1kW class module, achieving the performance surpassing the FY 1999 targets (average cell voltage: 0.70V, output: 1.27kW) with a simulated reformate gas at an air utilization rate of 20% and current density of 0.3A/cm{sup 2}. (NEDO)

  11. Development in fiscal 1999 of technologies to put photovoltaic power generation systems into practical use. Development of thin film solar cell manufacturing technologies (Development of technologies to manufacture applied type thin film solar cells with new structure and development of high-efficiency hybrid thin film/sheet solar cells); 1999 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu (oyogata shin kozo usumaku taiyo denchi no seizo gijutsu kaihatsu (kokoritsu hybrid gata usumaku / sheet taiyo denchi no seizo gijutsu kaihatsu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to develop low-cost and high-efficiency hybrid thin film/sheet solar cells, research and development has been performed. This paper summarizes the achievements in fiscal 1999. The research is related to a hybrid construction, in which the upper cells of amorphous silicon thin film are formed on the lower cells bonded with micro-crystalline silicon thin film relative to a poly-crystalline silicon sheet. In the technology to form the upper cells, a pin-construction using amorphous silicon thin film made by using the plasma CVD process was adopted, whereas an open circuit voltage of 1.45V, a short circuit current of 13.6 mA/cm{sup 2}, and a conversion efficiency of 13.5% were obtained. In the technology to form the substrate for the lower cells, formation of flat silicon thin plate that can be peeled off was identified as a result of adopting the construction in which a graphite substrate is provided on a rotating cooling body of 12-prism type. With regard to the technology to bond and form the lower cells, electrical properties of hetero-bonded cells were discussed, and an open circuit voltage of 0.605V and a conversion efficiency of 14.3% were obtained as a result of enhancing the film quality and optimizing the film thickness. (NEDO)

  12. FY 2001 report on the results of the survey of the environmentally friendly type energy community project. Utilization of combustible waste as solid fuel in Shimizu City, Shizuoka Prefecture, and the wide spread sphere of municipalities (Facilities such as RDF+LNG combined use high efficiency waste power generation); 2001 nendo Shizuoka ken shimizu shi oyobi koiki shichoson ken ni okeru kanensei haikibutsu kokeika nenryo riyo kankyo chowa gata energy komyuniti keisei sokushin hojo jigyo chosa (RDF+LNG heiyo kokoritsu haikibutsu hatsuden tou shisetsu) chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-03-01

    Survey/study were conducted of viability of an idea of the high efficiency power generation that combinedly use RDF from the refuse generated in Shizuoka/Yamanashi/Nagano prefectures and LNG from the LNG base in Shimizu City, Shizuoka Prefecture. In the survey of raw materials for RDF, the present amount that can be supplied to RDF power generation was estimated at 280 t/d in RDF and 4,300 Kcal/kg or more in heating value. As to the RDF/LNG combination power generation, combinations of RDF200t/d + 25MW (capacity of gas turbine power generation) or RDF200t/d + 70MW seem to be appropriate. And, 30% or more of RDF power generation efficiency is made possible. In the study of economical efficiency, expenses born by local governments were calculated supposing that the difference between the unit price of power selling and that of power generation in power generation is born by RDF suppliers. As a result, the share becomes approximately 8,600-12,000 yen/refuse t in 15-year operation, and was found lower than that in the existing small-/medium-scale refuse incineration treatment. The combustion flue gas associated with the power generation business becomes approximately 300,000 Nm{sup 3}/h. The gas turbine fuel is natural gas, and RDF is good in combustibility. Therefore, the effect on the environment is expected to be small. (NEDO)

  13. FY 2000 report on the results of the development of technology for commercialization of the photovoltaic power system - Development of production technology of thin film solar cells. Development of production technology of application type new structure thin film solar cells (Development of production technology of high efficiency hybrid thin films/sheet solar cells); 2000 nendo New sunshine keikaku seika hokokusho. Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu, Hakumaku taiyodenchi no seizo gijutsu kaihatsu, Oyogata shinkozo hakumaku taiyodenchi no seizo gijutsu kaihatsu, (Kokoritsu hybrid gata hakumaku / sheet taiyodenchi no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of realizing low cost and high efficiency hybrid thin films/sheet solar cells, the R and D were carried out, and the FY 2000 results were reported. As to the formation technology of the upper cell, the following technologies were developed and the results contributory to the heightening of efficiency were obtained: technology for improvement of cell characteristics by gap widening of p layer, technology for optimization of formation conditions of i layer corresponding to the hybrid solar cell, technology for heightening of current by the intermediate ZnO layer just under the upper cell. Relating to the development of formation technology of high quality microcrystal thin films, it was indicated that the microcrystal silicon thin film had the conformity effective also for polycrystal silicon, and at the same time, the conversion efficiency of 12.8% and release voltage of 0.579V were obtained by the cell using the cast polycrystal board. In the thin film/polycrystal sheet hybrid solar cell in which all these technologies were integrated, the conversion efficiency of 12.0% was achieved, and the possibility was verified of achieving the target efficiency of 14% by further improvement of FF. (NEDO)