WorldWideScience

Sample records for anion exchange variant

  1. Anion exchange membrane

    Science.gov (United States)

    Verkade, John G; Wadhwa, Kuldeep; Kong, Xueqian; Schmidt-Rohr, Klaus

    2013-05-07

    An anion exchange membrane and fuel cell incorporating the anion exchange membrane are detailed in which proazaphosphatrane and azaphosphatrane cations are covalently bonded to a sulfonated fluoropolymer support along with anionic counterions. A positive charge is dispersed in the aforementioned cations which are buried in the support to reduce the cation-anion interactions and increase the mobility of hydroxide ions, for example, across the membrane. The anion exchange membrane has the ability to operate at high temperatures and in highly alkaline environments with high conductivity and low resistance.

  2. Pu Anion Exchange Process Intensification

    Energy Technology Data Exchange (ETDEWEB)

    Taylor-Pashow, K. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-10-08

    This project seeks to improve the efficiency of the plutonium anion-exchange process for purifying Pu through the development of alternate ion-exchange media. The objective of the project in FY15 was to develop and test a porous foam monolith material that could serve as a replacement for the current anion-exchange resin, Reillex® HPQ, used at the Savannah River Site (SRS) for purifying Pu. The new material provides advantages in efficiency over the current resin by the elimination of diffusive mass transport through large granular resin beads. By replacing the large resin beads with a porous foam there is much more efficient contact between the Pu solution and the anion-exchange sites present on the material. Several samples of a polystyrene based foam grafted with poly(4-vinylpyridine) were prepared and the Pu sorption was tested in batch contact tests.

  3. Test procedure for anion exchange chromatography

    International Nuclear Information System (INIS)

    Plutonium from stored nitrate solutions will be sorbed onto anion exchange resins and converted to storable plutonium dioxide. Useful information will be simultaneously gained on the thermal stability and ion exchange capacity of four commercially available anion exchange resins over several years and under severe degradative conditions. This information will prove useful in predicting the safe and efficient lifetimes of these resins

  4. Advancements in Anion Exchange Membrane Cations

    Energy Technology Data Exchange (ETDEWEB)

    Sturgeon, Matthew R. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Long, Hai [National Renewable Energy Lab. (NREL), Golden, CO (United States); Park, Andrew M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Pivovar, Bryan S. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2015-10-15

    Anion-exchange membrane fuel cells (AME-FCs) are of increasingly popular interest as they enable the use of non-Pt fuel cell catalysts, the primary cost limitation of proton exchange membrane fuel cells. Benzyltrimethyl ammonium (BTMA) is the standard cation that has historically been utilized as the hydroxide conductor in AEMs. Herein we approach AEMs from two directions. First and foremost we study the stability of several different cations in a hydroxide solution at elevated temperatures. We specifically targeted BTMA and methoxy and nitro substituted BTMA. We've also studied the effects of adding an akyl spacer units between the ammonium cation and the phenyl group. In the second approach we use computational studies to predict stable ammonium cations, which are then synthesized and tested for stability. Our unique method to study cation stability in caustic conditions at elevated temperatures utilizes Teflon Parr reactors suitable for use under various temperatures and cation concentrations. NMR analysis was used to determine remaining cation concentrations at specific time points with GCMS analysis verifying product distribution. We then compare the experimental results with calculated modeling stabilities. Our studies show that the electron donating methoxy groups slightly increase stability (compared to that of BTMA), while the electron withdrawing nitro groups greatly decrease stability in base. These results give insight into possible linking strategies to be employed when tethering a BTMA like ammonium cation to a polymeric backbone; thus synthesizing an anion exchange membrane.

  5. Ionic Block Copolymers for Anion Exchange Membranes

    Science.gov (United States)

    Tsai, Tsung-Han; Herbst, Dan; Giffin, Guinevere A.; di Noto, Vito; Witten, Tom; Coughlin, E. Bryan

    2013-03-01

    Anion exchange membrane (AEM) fuel cells have regained interest because it allows the use of non-noble metal catalysts. Until now, most of the studies on AEM were based on random polyelectrolytes. In this work, Poly(vinylbenzyltrimethylammonium bromide)-b- (methylbutylene) ([PVBTMA][Br]-b-PMB) was studied by SAXS, TEM and dielectric spectroscopy to understand the fundamental structure-conductivity relationship of ion transport mechanisms within well-ordered block copolymers. The ionic conductivity and the formation of order structure were dependent on the casting solvent. Higher ion exchange capacity (IEC) of the membranes showed higher conductivity at as IEC values below 1.8mmol/g, as above this, the ionic conductivity decreases due to more water uptake leading to dilution of charge density. The humidity dependence of morphology exhibited the shifting of d-spacing to higher value and the alteration in higher characteristic peak of SAXS plot as the humidity increase from the dry to wet state. This phenomenon can be further explained by a newly developed polymer brush theory. Three ionic conduction pathways with different conduction mechanism within the membranes can be confirmed by broadband electric spectroscopy. US Army MURI (W911NF1010520)

  6. Rejuvenation processes applied to 'poisoned' anion exchangers in uranium processing

    International Nuclear Information System (INIS)

    The removal of 'poisons' from anion exchangers in uranium processing of Canadian radioactive ores is commonly called rejuvenation or regeneration. The cost of the ion exchange recovery of uranium is adversely affected by a decrease in the capacity and efficiency of the anion exchangers, due to their being 'poisoned' by silica, elemental sulphur, molybdenum and tetrathionates. These 'poisons' have a high affinity for the anion exchangers, are adsorbed in preference to the uranyl complex, and do not desorb with the reagents used normally in the uranyl desorption phase. The frequency of rejuvenation and the reagents required for rejuvenation are determined by the severity of the 'poisoning' accumulated by the exchanger in contact with the uranium leach liquor. Caustic soda (NaOH) at approximately equal to 18 cents/lb is commonly used to remove uranium anion exchangers of tetrathionate ((S406)/-/-) 'poisons'. A potential saving in operating cost would be of consequence if other reagents, e.g. sodium carbonate (Na2CO3) at approximately equal to 3.6 cents/lb or calcium hydroxide (Ca(OH)2) at approximately equal to 1.9 cents/lb, were effective in removing (S406)/-/-) from a 'poisoned' exchanger. A rejuvenation process for a test program was adopted after a perusal of the literature

  7. Inorganic anion exchangers for the treatment of radioactive wastes

    International Nuclear Information System (INIS)

    Inorganic anion exchangers are evaluated for Tc, I and S isotope removal from aqueous nuclear waste streams. Chemical, thermal, and radiation stabilities were examined. Selected exchangers were examined in detail for their selectivities, kinetics and mechanism of the sorption process (especially in NO3-, OH- and BO3- environments). Cement encapsulation and leaching experiments were made on the exchangers showing most promise for 'radwaste' treatment. (author)

  8. The assessment of pellicular anion-exchange resins for the determination of anions by ion chromatography

    International Nuclear Information System (INIS)

    Because pellicular anion-exchange resins suitable for the determination, by ion chromatography, of anions with alkaline eluents were unavailable in South Africa at the inception of this work, an attempt was made to prepare such resins. In this study it is shown that the pellicular resins produced are more efficient than the surface-aminated resins used previously. The simultaneous separation and determination of five common anions is demonstrated. The method was applied to the analysis of uranium leach liquors, effluent samples, and a solid sample of ferric oxide (goethite)

  9. Selection of anion exchange resins for boron thermal regeneration systems

    International Nuclear Information System (INIS)

    Boron concentration changes in the reactor coolant are effected using a new development called the boron thermal regeneration system (BTRS). Thermal regeneration refers to the use of ion-exchange resins in either retaining or releasing borate ions as a function of temperature. For the BTRS the equilibrium capacity of commercial and special anion exchange resins was investigated for the degree of cross-linking of anion resins. The equilibrium capacity increases with decreased temperature and depends strongly on the degree of cross-linking having the maximum point at about 7% of DVB. The temperature coefficient of equilibrium capacity of boric acid is also a function of the concentration of external solution and of the cross-linking having a maximum point of around 7% of DVB. Other basic characteristics of anion exchange resin were also investigated. (author)

  10. Mechanism of boric acid sorption on strongly basic anion exchangers

    International Nuclear Information System (INIS)

    The sorption was studied of boric acid at different temperatures and initial solution concentrations on the strongly basic anion exchange resin DIAION SA10A. The pH value of the ion exchange resin phase was determined using acidobasic indicators. The results of measurement, mathematically and graphically processed show that the increased sorption capacity of strongly basic anion exchange resins resulting from the increased concentration of the boric acid sorption solution is due to the presence of the polyborate forms (B3O3(OH)4- and B3O3(OH)52-) in the ion exchange phase. Increasing the temperature results in boric acid release from the ion exchange resin as a result of the transformation of sorbed polyborate forms to the simpler (B(OH)4-) forms. (Ha)

  11. Separation of B-10 with weakly basic anion exchange resin

    International Nuclear Information System (INIS)

    In the study of B-10 isotope separation with weakly basic anion exchanger, the sorption isotherms of boric acid on WA-21 weak-base anion exchange resin and the sorption band shapes as well as its migration velocities in a four-inch diameter ion exchange column, were studied. The isotherms show S-shapes with gentle slope at both low concentration and high concentration regions. In the band migration study, it has been found that these S-shaped isotherms affected the velocities of the peak maximum as the band migrated along the column. The velocities could be calculated with the simple solute movement equation. These results suggest that sorption of molecular species, rather than ion exchange of the counterions is the main process that occurs inside the pores of a weak-base ion exchange resin which is in contact with a very weak electrolytic solution, such as that of boric acid. (author)

  12. Void exclusion of antibodies by grafted-ligand porous particle anion exchangers.

    Science.gov (United States)

    Nian, Rui; Chuah, Cindy; Lee, Jeremy; Gan, Hui Theng; Latiff, Sarah Maria Abdul; Lee, Wan Yee; Vagenende, Vincent; Yang, Yuan-Sheng; Gagnon, Pete

    2013-03-22

    We describe a new variant of anion exchange chromatography in columns packed with porous particles that embody charged low-density polymer zones supported by a higher density polymer skeleton. IgG defies the norms of anion exchange and is excluded to the void volume at pH 3-10 and 0-4M NaCl. Void exclusion also occurs with Fab, F(ab')2, and IgM. Host cell protein contaminants mostly follow the usual norms of anion exchange and bind more strongly with increasing pH and decreasing conductivity. Sample buffer composition has no impact on partitioning so long as applied sample volume does not exceed the interparticle void volume of the column. Void-excluded antibody elutes in equilibration buffer. This seemingly conflicted collection of behaviors is reconciled by a variable size exclusion function mediated through the low-density polymer zones, the charge properties of the antibody species, and the pH and conductivity of the equilibration buffer. Current-generation porous particle anion exchangers that employ grafting techniques to achieve high charge density mediate void exclusion to varying degrees, with the best-suited achieving complete exclusion, and others as little as 65%. Perfusive and non-grafted particle-based exchangers mediate as little as 50% exclusion. Monoliths mediate no exclusion, due to their lack of an interparticle void volume. On qualified exchangers, the technique supports greater than 99% reduction of host proteins, DNA, and endotoxin. Virus is reduced more than 99.9%, and aggregates are reduced to less than 0.05%. The method supports better process control than other anion exchange formats because pH excursions in conjunction with changes in salt concentration do not occur until after the antibody has eluted from the column. PMID:23422893

  13. A lanthanide complex for metal encapsulations and anion exchanges.

    Science.gov (United States)

    Sun, Yan-Qiong; Wan, Fang; Li, Xin-Xiong; Lin, Jian; Wu, Tao; Zheng, Shou-Tian; Bu, Xianhui

    2016-08-01

    A cationic lanthanide metalloligand with 3 dangling carboxylate groups on its periphery co-assembles with nitrate into a porous thermochromic solid responsive to both external cations and anions, owing to the presence of exchangeable NO3(-) as well as cation cavities arising from cooperative orientation of free carboxylate groups. An especially interesting feature is the structural memory effect during crystallization exhibited by the metalloligand, even after dissolution and binding to secondary cations (Cu(2+), Cd(2+)…). Moreover, the porous solid can undergo ion-exchange with various anions, leading to tunable thermochromic temperature and color range. PMID:27463609

  14. Separation of boron isotopes using NMG type anion exchange resin

    International Nuclear Information System (INIS)

    Ion exchange separation of boron isotopes (B-10 and B-11) has been studied by using a special boron selective ion exchange resin; NMG (n-methyl glucamine)-type anion exchange resin. The resin has shown a large isotope separation coefficient of 1.02 at the experimental conditions of temperature, 80degC, and boric acid concentration, 0.2 M (mole/dm3). Enriched B-10 (92%) was obtained after the migration of 1149 m by a recyclic operation of ion exchange columns in a merry-go-round method. (author)

  15. Understanding and modeling removal of anionic organic contaminants (AOCs) by anion exchange resins.

    Science.gov (United States)

    Zhang, Huichun; Shields, Anthony J; Jadbabaei, Nastaran; Nelson, Maurice; Pan, Bingjun; Suri, Rominder P S

    2014-07-01

    Ionic organic contaminants (OCs) are a growing concern for water treatment and the environment and are removed inefficiently by many existing technologies. This study examined removal of anionic OCs by anion exchange resins (AXRs) as a promising alternative. Results indicate that two polystyrene AXRs (IRA910 and IRA96) have higher sorption capacities and selectivity than a polyacrylate resin (A860). For the polystyrene resins, selectivity follows: phenolates ≥ aromatic dicarboxylates > aromatic monocarboxylates > benzenesulfonate > aliphatic carboxylates. This trend can be explained based on hydration energy, the number of exchange groups, and aromaticity and hydrophobicity of the nonpolar moiety (NPM) of the anions. For A860, selectivity only varies within a narrow range (0.13-1.64). Despite the importance of the NPM of the anions, neutral solutes were sorbed much less, indicating synergistic combinations of electrostatic and nonelectrostatic interactions in the overall sorption. By conducting multiple linear regression between Abraham's descriptors and nature log of selectivity, induced dipole-related interactions and electrostatic interactions were found to be the most important interaction forces for sorption of the anions, while solute H-bond basicity has a negative effect. A predictive model was then developed for carboxylates and phenolates based on the poly parameter linear free energy relationships established for a diverse range of 16 anions and 5 neutral solutes, and was validated by accurate prediction of sorption of five test solutes within a wide range of equilibrium concentrations and that of benzoate at different pH. PMID:24877792

  16. Organic resin anion exchangers for the treatment of radioactive wastes

    International Nuclear Information System (INIS)

    Organic anion exchange resins are evaluated for 99-TcO4- (pertechnate) removed from aqueous nuclear waste streams. Chemical, thermal and radiation stabilities were studied. Selected resins were examined in detail for their selectivities in the presence of I-, NO3-, SO4=, CO3=, Cl- and OH-. Ion exchange equilibria and kinetic mechanisms were determined. Preliminary investigations of cement encapsulation in polymer modified form were made and some leach studies carried out. (author)

  17. Uptake of trace elements in human hair by anion exchange

    International Nuclear Information System (INIS)

    The sorption of some trace elements to human hair is studied by means of radioactive tracers. Experiments with 59Fe, 64Cu, 65Zn, 72Ga and 115Cd in HCl media show a great similarity between human hair and Dowex 1-x10, indicating that the hair acts as a strongly basic anion exchanger. A corresponding similarity with strong cation exchangers is not found. Specific sorption of trace elements seems to be of little use in hair identification studies. (author)

  18. Reducing nitrogen crossover in microbial reverse-electrodialysis cells by using adjacent anion exchange membranes and anion exchange resin

    KAUST Repository

    Wallack, Maxwell J.

    2015-01-01

    Microbial reverse electrodialysis cells (MRECs) combine power generation from salinity gradient energy using reverse electrodialysis (RED), with power generation from organic matter using a microbial fuel cell. Waste heat can be used to distill ammonium bicarbonate into high (HC) and low salt concentration (LC) solutions for use in the RED stack, but nitrogen crossover into the anode chamber must be minimized to avoid ammonia loses, and foster a healthy microbial community. To reduce nitrogen crossover, an additional low concentration (LC) chamber was inserted before the anode using an additional anion exchange membrane (AEM) next to another AEM, and filled with different amounts of anion or cation ion exchange resins. Addition of the extra AEM increased the ohmic resistance of the test RED stack from 103 Ω cm2 (1 AEM) to 295 Ω cm2 (2 AEMs). However, the use of the anion exchange resin decreased the solution resistance of the LC chamber by 74% (637 Ω cm2, no resin; 166 Ω cm2 with resin). Nitrogen crossover into the anode chamber was reduced by up to 97% using 50% of the chamber filled with an anion exchange resin compared to the control (no additional chamber). The added resistance contributed by the use of the additional LC chamber could be compensated for by using additional LC and HC membrane pairs in the RED stack.

  19. Cholangiocyte anion exchange and biliary bicarbonate excretion

    Institute of Scientific and Technical Information of China (English)

    Jesús M Banales; Jesús Prieto; Juan F Medina

    2006-01-01

    Primary canalicular bile undergoes a process of fluidization and alkalinization along the biliary tract that is influenced by several factors including hormones, innervation/neuropeptides, and biliary constituents. Theexcretion of bicarbonate at both the canaliculi and the bile ducts is an important contributor to the generation of the so-called bile-salt independent flow. Bicarbonate is secreted from hepatocytes and cholangiocytes through parallel mechanisms which involve chloride efflux through activation of Cl- channels, and further bicarbonate secretion via AE2/SLC4A2-mediated Cl-/HCO3-exchange. Glucagon and secretin are two relevant hormones which seem to act very similarly in their target cells (hepatocytes for the former and cholangiocytes for the latter). These hormones interact with their specific G protein-coupled receptors, causing increases in intracellular levels of cAMP and activation of cAMP-dependent Cl- and HCO3- secretory mechanisms. Both hepatocytes and cholangiocytes appear to have cAMP-responsive intracellular vesicles in which AE2/SLC4A2 colocalizes with cell specific Cl- channels (CFTR in cholangiocytes and not yet determined in hepatocytes) and aquaporins (AQP8 in hepatocytes and AQP1 in cholangiocytes). cAMP-induced coordinated trafficking of these vesicles to either canalicular or cholangiocyte lumenal membranes and further exocytosis results in increased osmotic forces and passive movement of water with net bicarbonate-rich hydrocholeresis.

  20. The immobilization of anion exchange resins in polymer modified cements

    International Nuclear Information System (INIS)

    Organic anion exchange resins, loaded with 99-Tc as the pertechnate ion, were incorporated into polymer modified cements (Flexocrete Ltd, Preston). BFS/OPC (9:1 mix) also was modified by three polymers from the same source (styrene acrylic (2) styrene butadiene) and loaded with anion exchanger containing the pertechnate. Composites were tested for initial compressive strengths, under water and radiation stability and leach rate. IAEA standard leach testing was with simulated sea and ground waters. Ground water leaching also was carried out on composites subjected to 1.109 rads (γ). Leach testing correlated well with compressive strength. Modified composites performed better than the BFS/OPC mix under all conditions studied and were able to encapsulate higher resin loadings. (author)

  1. Alkaline Anion-Exchange Membranes Containing Mobile Ion Shuttles.

    Science.gov (United States)

    Ge, Xiaolin; He, Yubin; Guiver, Michael D; Wu, Liang; Ran, Jin; Yang, Zhengjin; Xu, Tongwen

    2016-05-01

    A new class of alkaline anion-exchange membranes containing mobile ion shuttles is developed. It is achieved by threading ionic linear guests into poly(crown ether) hosts via host-guest molecular interaction. The thermal- and pH-triggered shuttling of ionic linear guests remarkably increases the solvation-shell fluctuations in inactive hydrated hydroxide ion complexes (OH(-) (H2 O)4 ) and accelerates the OH(-) transport. PMID:26972938

  2. A Novel Methodology to Synthesize Highly Conductive Anion Exchange Membranes

    OpenAIRE

    Yubin He; Jiefeng Pan; Liang Wu; Yuan Zhu; Xiaolin Ge; Jin Ran; ZhengJin Yang; Tongwen Xu

    2015-01-01

    Alkaline polyelectrolyte fuel cell now receives growing attention as a promising candidate to serve as the next generation energy-generating device by enabling the use of non-precious metal catalysts (silver, cobalt, nickel et al.). However, the development and application of alkaline polyelectrolyte fuel cell is still blocked by the poor hydroxide conductivity of anion exchange membranes. In order to solve this problem, we demonstrate a methodology for the preparation of highly OH− conductiv...

  3. Anion exchangers with branched functional ion exchange layers of different hydrophilicity for ion chromatography.

    Science.gov (United States)

    Shchukina, O I; Zatirakha, A V; Smolenkov, A D; Nesterenko, P N; Shpigun, O A

    2015-08-21

    Novel polystyrene-divinylbenzene (PS-DVB) based anion exchangers differing from each other in the structure of the branched functional ion exchange layer are prepared to investigate the role of linker and functional site on ion exchange selectivity. The proposed method of synthesis includes the obtaining of aminated PS-DVB particles by means of their acylation with following reductive amination with methylamine. Further modification of the obtained secondary aminogroups is provided by the alkylation with either 1,4-butanediol diglycidyl ether (1,4-BDDGE) or resorcinol diglycidyl ether (RDGE), which form the linkers of different hydrophobicity, and amination of terminal epoxide rings with trimethylamine (TMA), dimethylethanolamine (DMEA), methyldiethanolamine (MDEA) or triethanolamine (TEA). The variation of the structure and hydrophobicity of the linker and terminal quaternary ammonium sites in the functional layer allows the alteration of selectivity and separation efficiency of the obtained adsorbents. The ion exchange selectivity and separation efficiency of the anion exchangers are evaluated using the model mixtures of anions (F(-), HCOO(-), Cl(-), NO2(-), Br(-), NO3(-), HPO4(2-) and SO4(2-)) in potassium hydroxide eluents. The adsorbents show the decrease of selectivity with increasing the hydrophilicity of the terminal functional site. The anion exchangers having more flexible and hydrophilic 1,4-BDDGE linker provide smaller separation factors for most of the analytes as compared with RDGE-containing adsorbents with the same terminal ion exchange sites, but are characterized with higher column efficiencies and better peak symmetry for polarizable anions. In case of 1,4-BDDGE-modified anion exchangers of the particle size of 3.3μm functionalized with DMEA and MDEA the calculated values of column efficiencies for polarizable NO3(-) and Br(-) are up to 49,000 and 53,000N/m, respectively, which is almost twice higher than the values obtained for the RDGE

  4. Fixing of metallic acetates on an anion-exchange resin

    International Nuclear Information System (INIS)

    After giving a brief review of the theoretical principles governing the fixation of anionic complexes of metallic elements on an anion exchange resin, we consider the particular case of uranyl acetate. By plotting the partition curves we have been able to calculate the exchange constants in the resin. By studying the changes in the logarithm of the limiting partition coefficient as a function of the logarithm of the free acetate ion concentration, it has been possible to calculate the dissociation constants for the complexes in solution. The fixation of a large number of metallic acetates has been studied. All the tests have been negative except in the case of mercury. For this reason we have been able to consider the possibility of separating uranium from a certain number of elements. Some of these separations are possible even in the presence of interfering anions such as chlorides which have a greater affinity for the resin than have the acetate ions. In the case of water-ethanol and water-isopropanol mixtures, we have improved the conditions under which copper acetate and mercury acetate may be fixed. This study has enabled us to calculate the dissociation constant for the CuAc3- complex in the mixtures water +40% (by weight) isopropanol and water +50% (by weight) isopropanol. It should also make it possible to use separation conditions which could not hitherto be applied in aqueous media. (author)

  5. Removal of chromium complex dye from aqueous solutions using strongly basic and weakly basic anion exchangers

    OpenAIRE

    Kauspediene, D.; Kazlauskiene E.; Selskiene, A.

    2010-01-01

    Removal of chromium complex dye from aqueous solutions by sorption onto a weakly basic, acrylic matrix anion exchanger Purolite A845 and a strongly basic, polystyrene matrix anion exchanger Purolite A 500P has been investigated under various experimental conditions: the initial dye concentration, pH and temperature. The sorption of chromium complex dye proceeds as a result of miscellaneous interactions between the dye and anion exchanger: ion exchange and physical sorption. The removal effici...

  6. Fixation of metallic sulfosalicylate complexes on an anionic exchange resin

    International Nuclear Information System (INIS)

    Since sulfosalicylate ions have acid-base properties, sulfosalicylate complexes have an apparent stability which varies with the ph. As a result, the fixation of sulfo-salicylates on an anionic exchange resin depends on the ph of the solution in equilibrium with the resin. This research has been aimed at studying the influence of the ph on the fixation on an anionic exchange resin (Dowex 1 x 4) of sulfosalicylate anions on the one hand, and of metallic sulfosalicylate complexes on the other hand. In the first part of this work, a determination has been made, by frontal analysis of the distribution of sulfosalicylate ions in the resin according to the total sulfosalicylate I concentration in the aqueous solution in equilibrium with the resin. The exchange constants of these ions between the resin and the solution have been calculated. In the second part, a study has been made of the fixation of anionic sulfosalicylate complexes of Fe(III), Al(III), Cr(III), Cu(II), Ni(II), Co(II), Zn(II), Mn(II), Cd(II), Fe(II) and UO22+. By measuring the partition coefficients of these different elements between the resin and the solution it has been possible to give interpretation for the modes of fixation of the metallic ions, and to calculate their exchange constant between the resin and the solution. The relationship has been established for each metallic element studied, between its partition coefficient, the ph and the total concentration of the complexing agent in solution. Such a relationship makes it possible to predict, for given conditions, the nature of the species in solution and in the resin, as well as the partition coefficient of a metallic, element. Finally, in the third part of the work, use has been made of results obtained previously, to carry out some separations (Ni2+ - Co2+; Ni2+ - Co2+ - Cu2+; UO22+ - Fe3+; UO22+ - Cr3+; UO22+ - Cu2+; UO22+ - Ni2+; UO22+ - Co2+; UO22+ - Mn2+ and UO22+ - Cd2+), as well as the purification of a uranyl sulfosalicylate solution

  7. Extracellular Cl(-) regulates human SO4 (2-)/anion exchanger SLC26A1 by altering pH sensitivity of anion transport.

    Science.gov (United States)

    Wu, Meng; Heneghan, John F; Vandorpe, David H; Escobar, Laura I; Wu, Bai-Lin; Alper, Seth L

    2016-08-01

    Genetic deficiency of the SLC26A1 anion exchanger in mice is known to be associated with hyposulfatemia and hyperoxaluria with nephrolithiasis, but many aspects of human SLC26A1 function remain to be explored. We report here the functional characterization of human SLC26A1, a 4,4'-diisothiocyanato-2,2'-stilbenedisulfonic acid (DIDS)-sensitive, electroneutral sodium-independent anion exchanger transporting sulfate, oxalate, bicarbonate, thiosulfate, and (with divergent properties) chloride. Human SLC26A1-mediated anion exchange differs from that of its rodent orthologs in its stimulation by alkaline pHo and inhibition by acidic pHo but not pHi and in its failure to transport glyoxylate. SLC26A1-mediated transport of sulfate and oxalate is highly dependent on allosteric activation by extracellular chloride or non-substrate anions. Extracellular chloride stimulates apparent V max of human SLC26A1-mediated sulfate uptake by conferring a 2-log decrease in sensitivity to inhibition by extracellular protons, without changing transporter affinity for extracellular sulfate. In contrast to SLC26A1-mediated sulfate transport, SLC26A1-associated chloride transport is activated by acid pHo, shows reduced sensitivity to DIDS, and exhibits cation dependence of its DIDS-insensitive component. Human SLC26A1 resembles SLC26 paralogs in its inhibition by phorbol ester activation of protein kinase C (PKC), which differs in its undiminished polypeptide abundance at or near the oocyte surface. Mutation of SLC26A1 residues corresponding to candidate anion binding site-associated residues in avian SLC26A5/prestin altered anion transport in patterns resembling those of prestin. However, rare SLC26A1 polymorphic variants from a patient with renal Fanconi Syndrome and from a patient with nephrolithiasis/calcinosis exhibited no loss-of-function phenotypes consistent with disease pathogenesis. PMID:27125215

  8. The sorption capacity of boron on anionic-exchange resin

    International Nuclear Information System (INIS)

    Boron sorption capacities on anionic-exchange resins vary with temperature, concentration, and resin cross-linkage. A semiempirical correlation, developed from boron solution chemistry, is presented to account for these variations. The relationship, based on boron chemistry and changes in Gibb's energy, can be stated approximately as Q = a1CBa2Za3 exp[-(a4T + a5T2 + a6Z0.5)]. Correlation parameters, which vary with resin type, are evaluated experimentally. Parameter values for macroporous resin Diaion PA 300 and for gel-type resins Diaion SA10 and Amberlite IRN 78LC are presented. The resulting expression is used to determine boron sorption and desorption limitations on ion exchangers at various temperatures and concentrations, and to determine the interfacial boron concentration in equilibrium and rate models

  9. Anion exchange kinetics of uranium in sulphate media

    International Nuclear Information System (INIS)

    Experiments have shown that the sorption of uranium from acidic sulphate solutions onto strong base-anion exchange resins is particle diffusion controlled in the uranium concentration range 0.0001 to 0.004 M. A simplified diffusion model, based on Fick's Law, fits the kinetic data at each concentration. The rate of sorption falls significantly at lowered solution concentration. This corresponds with a lowered equilibrium loading of uranium and can be predicted with the Nernst-Planck equations using the measured self diffusion coefficient of uranium (1.65 x 10-8 cm2/s) and sulphate ions. The importance of this lowering of uranium sorption on the design of ion exchange equipment is stressed. (author)

  10. A Novel Methodology to Synthesize Highly Conductive Anion Exchange Membranes

    Science.gov (United States)

    He, Yubin; Pan, Jiefeng; Wu, Liang; Zhu, Yuan; Ge, Xiaolin; Ran, Jin; Yang, Zhengjin; Xu, Tongwen

    2015-08-01

    Alkaline polyelectrolyte fuel cell now receives growing attention as a promising candidate to serve as the next generation energy-generating device by enabling the use of non-precious metal catalysts (silver, cobalt, nickel et al.). However, the development and application of alkaline polyelectrolyte fuel cell is still blocked by the poor hydroxide conductivity of anion exchange membranes. In order to solve this problem, we demonstrate a methodology for the preparation of highly OH- conductive anion exchange polyelectrolytes with good alkaline tolerance and excellent dimensional stability. Polymer backbones were grafted with flexible aliphatic chains containing two or three quaternized ammonium groups. The highly flexible and hydrophilic multi-functionalized side chains prefer to aggregate together to facilitate the formation of well-defined hydrophilic-hydrophobic microphase separation, which is crucial for the superior OH- conductivity of 69 mS/cm at room temperature. Besides, the as-prepared AEMs also exhibit excellent alkaline tolerance as well as improved dimensional stability due to their carefully designed polymer architecture, which provide new directions to pursue high performance AEMs and are promising to serve as a candidate for fuel cell technology.

  11. Investigation of Polyacrylate Anion-Exchangers for Separation of Rare Earth Element Complexes with EDTA

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The rare earth complexes with EDTA, Ln(edta), show an unusual sequence of affinity for the anion-exchangers. The sorption and chromatographic separation of Y3+ for Nd3+ complexes with EDTA was studied by using the strongly basic gel and macroporous polyacrylate anion-exchangers, Amberlite IRA 458 and Amberlite 958, and the weakly basic gel polyacrylate anion-exchanger, Amberlite IRA-68. The investigations on sorption and separation of rare earth complexes with EDTA on the polyacrylate anion-exchangers applied mainly in the environment protection so far indicate that they can be applied in anionexchange separation of lanthanide complexes with aminopolycarboxylic acids. It was shown that the weakly basic polyacrylate gel anion-exchanger Amberlite IRA-68 is the most effective in purification of Y3+ from Nd3+ in comparison with the strongly basic anion-exchangers of this type.

  12. Computer simulation of methanol exchange dynamics around cations and anions

    Energy Technology Data Exchange (ETDEWEB)

    Roy, Santanu; Dang, Liem X.

    2016-03-03

    In this paper, we present the first computer simulation of methanol exchange dynamics between the first and second solvation shells around different cations and anions. After water, methanol is the most frequently used solvent for ions. Methanol has different structural and dynamical properties than water, so its ion solvation process is different. To this end, we performed molecular dynamics simulations using polarizable potential models to describe methanol-methanol and ion-methanol interactions. In particular, we computed methanol exchange rates by employing the transition state theory, the Impey-Madden-McDonald method, the reactive flux approach, and the Grote-Hynes theory. We observed that methanol exchange occurs at a nanosecond time scale for Na+ and at a picosecond time scale for other ions. We also observed a trend in which, for like charges, the exchange rate is slower for smaller ions because they are more strongly bound to methanol. This work was supported by the US Department of Energy, Office of Science, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences, and Biosciences. The calculations were carried out using computer resources provided by the Office of Basic Energy Sciences.

  13. Anion-exchangeable inorganic-organic hybrid materials synthesized without using templates

    Institute of Scientific and Technical Information of China (English)

    XU Xianzhu; SONG Jiangwei; LI Defeng; XIAO Fengshou

    2004-01-01

    Inorganic-organic hybrid materials have been obtained at room temperature in aqueous solution without using the templates of surfactants. The materials are care fully characterized by anion-exchange measurement, elements analysis, X-ray diffraction, and infrared spectroscopy. Notably, the anion-exchange capacity of the samples (3.9 Interestingly, both small and large anions could be easily exchanged into the samples due to the plasticity of the sam pies, along with the phase transition.

  14. Optimized anion exchange membranes for vanadium redox flow batteries.

    Science.gov (United States)

    Chen, Dongyang; Hickner, Michael A; Agar, Ertan; Kumbur, E Caglan

    2013-08-14

    In order to understand the properties of low vanadium permeability anion exchange membranes for vanadium redox flow batteries (VRFBs), quaternary ammonium functionalized Radel (QA-Radel) membranes with three ion exchange capacities (IECs) from 1.7 to 2.4 mequiv g(-1) were synthesized and 55-60 μm thick membrane samples were evaluated for their transport properties and in-cell battery performance. The ionic conductivity and vanadium permeability of the membranes were investigated and correlated to the battery performance through measurements of Coulombic efficiency, voltage efficiency and energy efficiency in single cell tests, and capacity fade during cycling. Increasing the IEC of the QA-Radel membranes increased both the ionic conductivity and VO(2+) permeability. The 1.7 mequiv g(-1) IEC QA-Radel had the highest Coulombic efficiency and best cycling capacity maintenance in the VRFB, while the cell's voltage efficiency was limited by the membrane's low ionic conductivity. Increasing the IEC resulted in higher voltage efficiency for the 2.0 and 2.4 mequiv g(-1) samples, but the cells with these membranes displayed reduced Coulombic efficiency and faster capacity fade. The QA-Radel with an IEC of 2.0 mequiv g(-1) had the best balance of ionic conductivity and VO(2+) permeability, achieving a maximum power density of 218 mW cm(-2) which was higher than the maximum power density of a VRFB assembled with a Nafion N212 membrane in our system. While anion exchange membranes are under study for a variety of VRFB applications, this work demonstrates that the material parameters must be optimized to obtain the maximum cell performance. PMID:23799776

  15. Enhanced DOC removal using anion and cation ion exchange resins.

    Science.gov (United States)

    Arias-Paic, Miguel; Cawley, Kaelin M; Byg, Steve; Rosario-Ortiz, Fernando L

    2016-01-01

    Hardness and DOC removal in a single ion exchange unit operation allows for less infrastructure, is advantageous for process operation and depending on the water source, could enhance anion exchange resin removal of dissolved organic carbon (DOC). Simultaneous application of cationic (Plus) and anionic (MIEX) ion exchange resin in a single contact vessel was tested at pilot and bench scales, under multiple regeneration cycles. Hardness removal correlated with theoretical predictions; where measured hardness was between 88 and 98% of the predicted value. Comparing bench scale DOC removal of solely treating water with MIEX compared to Plus and MIEX treated water showed an enhanced DOC removal, where removal was increased from 0.5 to 1.25 mg/L for the simultaneous resin application compared to solely applying MIEX resin. A full scale MIEX treatment plant (14.5 MGD) reduced raw water DOC from 13.7 mg/L to 4.90 mg/L in the treated effluent at a bed volume (BV) treatment rate of 800, where a parallel operation of a simultaneous MIEX and Plus resin pilot (10 gpm) measured effluent DOC concentrations of no greater than 3.4 mg/L, even at bed volumes of treatment 37.5% greater than the full scale plant. MIEX effluent compared to simultaneous Plus and MIEX effluent resulted in differences in fluorescence intensity that correlated to decreases in DOC concentration. The simultaneous treatment of Plus and MIEX resin produced water with predominantly microbial character, indicating the enhanced DOC removal was principally due to increased removal of terrestrially derived organic matter. The addition of Plus resin to a process train with MIEX resin allows for one treatment process to remove both DOC and hardness, where a single brine waste stream can be sent to sewer at a full-scale plant, completely removing lime chemical addition and sludge waste disposal for precipitative softening processes. PMID:26624231

  16. A Simple Halide-to-Anion Exchange Method for Heteroaromatic Salts and Ionic Liquids

    Directory of Open Access Journals (Sweden)

    Neus Mesquida

    2012-04-01

    Full Text Available A broad and simple method permitted halide ions in quaternary heteroaromatic and ammonium salts to be exchanged for a variety of anions using an anion exchange resin (A− form in non-aqueous media. The anion loading of the AER (OH− form was examined using two different anion sources, acids or ammonium salts, and changing the polarity of the solvents. The AER (A− form method in organic solvents was then applied to several quaternary heteroaromatic salts and ILs, and the anion exchange proceeded in excellent to quantitative yields, concomitantly removing halide impurities. Relying on the hydrophobicity of the targeted ion pair for the counteranion swap, organic solvents with variable polarity were used, such as CH3OH, CH3CN and the dipolar nonhydroxylic solvent mixture CH3CN:CH2Cl2 (3:7 and the anion exchange was equally successful with both lipophilic cations and anions.

  17. Reillex/trademark/ HPQ: A new, macroporous polyvinylpyridine resin for separating plutonium using nitrate anion exchange

    International Nuclear Information System (INIS)

    Anion exchange in nitric acid is the major aqueous process used to recover and purify plutonium from impure scrap materials. Most strong-base anion exchange resins incorporate a styrene-divinylbenzene copolymer. A newly available, macroporous anion exchange resin based on a copolymer of 1-methyl-4-vinylpyridine and divinylbenzene has been evaluated. Comparative data for Pu(IV) sorption kinetics and capacity are presented for this new resin and two other commonly used anion exchange resins. The new resin offers high capacity and rapid sorption kinetics for Pu(IV) from nitric acid, as well as greater stability to chemical and radiolytic degradation. 8 refs., 12 figs

  18. Liquid anion-exchange separation of vanadium from malonate media

    International Nuclear Information System (INIS)

    Vanadium (IV) and (V) can be quantitatively extracted with 0.2 mol/l Amberlite LA-2 in xylene at pH 3.0 from 0.02 mol/l malonic acid, stripped with 0.5 mol/l hydrochloric acid, and determined spectrophotometrically. Five other liquid anion exchangers (Amberlite LA-1, Primene JM-T, Aliquat 336S, TOA and TIOA) were examined as possible extractants. The extraction of vanadium(IV) was found to be quantitative only with Amberlite LA-2, while that of vanadium(V) was quantitative with Amberlite LA-1 and LA-2, Primene JM-T and Aliquat 336S. Eight common solvents were tested as diluents; of these hexane, cyclohexane, benzene, and xylene were found to be satisfactory. Vanadium was separated from elements that do not form anionic complexes with malonic acid by selective extraction, from those that form weak complexes by washing the organic extract with water, and from metals that form strong malonato complexes by selective stripping with hydrochloric, nitric, or sulphuric acid. The method has been applied to the determination of vanadium in steel, coal fly ash and fuel oil. The precision of measurement is within ±5% and the detection limit of the method for vanadium is 0.5 mg/kg. (orig.)

  19. The anion exchange behavior of Te and Sb

    International Nuclear Information System (INIS)

    The absorption behavior of Te and Sb in different oxidation states by anion exchange resins in hydrochloric acid medium has been studied. Distribution coefficients for Te(IV), Te(VI) as a function of HCl acid concentration (up to 3M HCl) have been determined. The absorbability for Sb(III) was noticed to be very high and could not be eluted out of the column using HCl as eluent. Sb(V) could be eluted quantitatively using 3M HCl. The present study clearly indicate that due to the EC/β+ decay of the parent isotopes 117,118Te, the daughter nuclei 117,118Sb are produced predominantly as Sb(III). (author)

  20. Uranium isotope separation by continuous anion exchange chromatography

    International Nuclear Information System (INIS)

    This paper reports a process for producing nuclear quality Uranium 235 (U235) from a substantially impure feed stock containing a mixture of uranium isotopes, including U235, forming a stationary phase from an anion exchange resin in the annulus of a rotating annular chromatograph; feeding the feed stock to the stationary phase to load less than 10% of the stationary phase; injecting a mobile phase comprising an eluant selected from the group consisting of aqueous solutions of sulfates, chlorides, nitrates and carbonates into the stationary phase; continuously rotating the annular chromatograph; collecting the U235 isotope in substantially pure, enriched form from the stationary phase; precipitating the U235 isotope as ammonium diurante with ammonium hydroxide; and calcining the ammonium diuranate to produce uranium oxide rich in U235 suitable for nuclear applications requiring substantially pure U235

  1. Alkaline direct alcohol fuel cells using an anion exchange membrane

    Energy Technology Data Exchange (ETDEWEB)

    Matsuoka, Koji; Iriyama, Yasutoshi; Abe, Takeshi; Ogumi, Zempachi [Department of Energy and Hydrocarbon Chemistry, Graduate School of Engineering, Kyoto University, Katsura, Nishikyo-ku, Kyoto 615-8510 (Japan); Matsuoka, Masao [Faculty of Science and Engineering, Ritsumeikan University, Kusatsu, Shiga 525-8577 (Japan)

    2005-10-04

    Alkaline direct alcohol fuel cells using an OH-form anion exchange membrane and polyhydric alcohols were studied. A high open circuit voltage of ca. 800mV was obtained for a cell using Pt-Ru/C (anode) and Pt/C (cathode) at 323K, which was about 100-200mV higher than that for a DMFC using Nafion{sup R}. The maximum power densities were in the order of ethylene glycol>glycerol>methanol>erythritol>xylitol. Silver catalysts were used as a cathode catalyst to fabricate alkaline fuel cells, since silver catalyst is almost inactive in the oxidation of polyhydric alcohols. Alkaline direct ethylene glycol fuel cells using silver as a cathode catalyst gave excellent performance because higher concentrations of fuel could be supplied to the anode. (author)

  2. 3D Printing of Micropatterned Anion Exchange Membranes.

    Science.gov (United States)

    Seo, Jiho; Kushner, Douglas I; Hickner, Michael A

    2016-07-01

    Micropatterned anion exchange membranes (AEMs) have been 3D printed via a photoinitiated free radical polymerization and quaternization process. The photocurable formulation, consisting of diurethane dimethacrylate (DUDA), poly(ethylene glycol) diacrylate (PEGDA), dipentaerythritol penta-/hexa- acrylate, and 4-vinylbenzyl chloride (VBC), was directly cured into patterned films using a custom 3D photolithographic printing process similar to stereolithography. Measurements of water uptake, permselectivity, and ionic resistance were conducted on the quaternized poly(DUDA-co-PEGDA-co-VBC) sample series to determine their suitability as ion exchange membranes. The water uptake of the polymers increased as the ion exchange capacity (IEC) increased due to greater quaternized VBC content. Samples with IEC values between 0.98 to 1.63 mequiv/g were synthesized by varying the VBC content from 15 to 25 wt %. The water uptake was sensitive to the PEGDA content in the network resulting in water uptake values ranging from 85 to 410 wt % by varying the PEGDA fractions from 0 to 60 wt %. The permselectivity of the AEM samples decreased from 0.91 (168 wt %, 1.63 mequiv/g) to 0.85 (410 wt %, 1.63 mequiv/g) with increasing water uptake and to 0.88 (162 wt %, 0.98 mequiv/g) with decreasing IEC. Permselectivity results were relatively consistent with the general understanding of the correlation between permselectivity, water uptake, and ion content of the membrane. Lastly, it was revealed that the ionic resistance of patterned membranes was lower than that of flat membranes with the same material volume or equivalent thickness. A parallel resistance model was used to explain the influence of patterning on the overall measured ionic resistance. This model may provide a way to maximize ion exchange membrane performance by optimizing surface patterns without chemical modification to the membrane. PMID:27218137

  3. Removal of bromide and natural organic matter by anion exchange.

    Science.gov (United States)

    Hsu, Susan; Singer, Philip C

    2010-04-01

    Bromide removal by anion exchange was explored for various water qualities, process configurations, and resin characteristics. Simulated natural waters containing different amounts of natural organic matter (NOM), bicarbonate, chloride, and bromide were treated with a polyacrylate-based magnetic ion exchange (MIEX) resin on a batch basis to evaluate the effectiveness of the resin for removal of bromide. While bromide removal was achieved to some degree, alkalinity (bicarbonate), dissolved organic carbon (DOC), and chloride were shown to inhibit bromide removal in waters with bromide concentrations of 100 and 300 microg/L. Water was also treated using a two-stage batch MIEX process. Two-stage treatment resulted in only a slight improvement in bromide removal compared to single-stage treatment, presumably due to competition with the high concentration of chloride which is present along with bromide in natural waters. In view of the relatively poor bromide removal results for the MIEX resin, a limited set of experiments was performed using polystyrene resins. DOC and bromide removal were compared by treating model waters with MIEX and two polystyrene resins, Ionac A-641 and Amberlite IRA910. The two polystyrene resins were seen to be more effective for bromide removal, while the MIEX resin was more effective at removing DOC. PMID:20045170

  4. Gamma radiation effect on gas production in anion exchange resins

    International Nuclear Information System (INIS)

    Radiation-induced decomposition of Amberlite IRA400 anion exchange resin in hydroxide form by gamma radiolysis has been studied at various doses in different atmospheres (anaerobic, anaerobic with liquid water, and aerobic). The effect of these parameters on the degradation of ion exchange resins is rarely investigated in the literature. We focused on the radiolysis gases produced by resin degradation. When the resin was irradiated under anaerobic conditions with liquid water, the liquid phase over the resin was also analyzed to identify any possible water-soluble products released by degradation of the resin. The main products released are trimethylamine (TMA), molecular hydrogen (H2g) and carbon dioxide (CO2g). TMA and H2g are produced in all the irradiation atmospheres. However, TMA was in gaseous form under anaerobic and aerobic conditions and in aqueous form in presence of liquid water. In the latter conditions, TMAaq was associated with aqueous dimethylamine (DMAaq), monomethylamine (MMAaq) and ammonia (NH4+aq). CO2g is formed in the presence of oxygen due to oxidation of organic compounds present in the system, in particular the degradation products such as TMAg

  5. Hydroxide Solvation and Transport in Anion Exchange Membranes

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Chen [Univ. of Chicago, IL (United States); Wuhan Univ. (China); Tse, Ying-Lung Steve [Univ. of Chicago, IL (United States); Lindberg, Gerrick E. [Northern Arizona Univ., Flagstaff, AZ (United States); Knight, Chris [Argonne National Lab. (ANL), Argonne, IL (United States); Voth, Gregory A. [Univ. of Chicago, IL (United States)

    2016-01-27

    Understanding hydroxide solvation and transport in anion exchange membranes (AEMs) can provide important insight into the design principles of these new membranes. To accurately model hydroxide solvation and transport, we developed a new multiscale reactive molecular dynamics model for hydroxide in aqueous solution, which was then subsequently modified for an AEM material. With this model, we investigated the hydroxide solvation structure and transport mechanism in the membrane. We found that a relatively even separation of the rigid side chains produces a continuous overlapping region for hydroxide transport that is made up of the first hydration shell of the tethered cationic groups. Our results show that hydroxide has a significant preference for this overlapping region, transporting through it and between the AEM side chains with substantial contributions from both vehicular (standard diffusion) and Grotthuss (proton hopping) mechanisms. Comparison of the AEM with common proton exchange membranes (PEMs) showed that the excess charge is less delocalized in the AEM than the PEMs, which is correlated with a higher free energy barrier for proton transfer reactions. The vehicular mechanism also contributes considerably more than the Grotthuss mechanism for hydroxide transport in the AEM, while our previous studies of PEM systems showed a larger contribution from the Grotthuss mechanism than the vehicular mechanism for proton transport. The activation energy barrier for hydroxide diffusion in the AEM is greater than that for proton diffusion in PEMs, implying a more significant enhancement of ion transport in the AEM at elevated temperatures.

  6. Determination of arsenate in water by anion selective membrane electrode using polyurethane–silica gel fibrous anion exchanger composite

    International Nuclear Information System (INIS)

    Highlights: • PU–Si gel is new anion exchanger material synthesized and characterized. • This material used as anion exchange membrane is applied for electroanalytical studies. • The method for detection and determination of AsO43− in traces amounts discussed. • The results are also verified from arsenic analyzer. -- Abstract: Polyurethane (PU)–silica (Si gel) based fibrous anion exchanger composites were prepared by solid–gel polymerization of polyurethane in the presence of different amounts of silica gel. The formation of PU–Si gel fibrous anion exchanger composite was characterized by Fourier transform infra-red spectroscopy (FTIR), X-ray diffraction (XRD), thermogravimetric analysis (TGA-DTA), scanning electron microscopy (SEM) and elemental analysis. The membrane having a composition of 5:3 (PU:Si gel) shows best results for water content, porosity, thickness and swelling. Our studies show that the present ion selective membrane electrode is selective for arsenic, having detection limit (1 × 10−8 M to 1 × 10−1 M), response time (45 s) and working pH range (5–8). The selectivity coefficient values for interfering ions indicate good selectivity for arsenate (AsO43−) over interfering anions. The accuracy of the detection limit results was compared by PCA-Arsenomat

  7. Evaluation of indigenous anion exchange resins for plutonium purification - effect of gamma radiation

    International Nuclear Information System (INIS)

    The purification and concentration of plutonium is carried out presently with an imported anion exchange resin (Dowex 1X4). A programme has been initiated in our laboratory to substitute the same with indigenous resins. In this connection, the effect of gamma radiation on imported and indigenous anion exchange resins has been studied in nitric acid medium and its influence on total exchange capacity, strong base capacity and plutonium distribution ratio (Kd) are presented in this paper. (author)

  8. Sorption of Pu(IV) from nitric acid by bifunctional anion-exchange resins

    International Nuclear Information System (INIS)

    Anion exchange is attractive for separating plutonium because the Pu(IV) nitrate complex is very strongly sorbed and few other metal ions form competing anionic nitrate complexes. The major disadvantage of this process has been the unusually slow rate at which the Pu(IV) nitrate complex is sorbed by the resin. The paper summarizes the concept of bifunctional anion-exchange resins, proposed mechanism for Pu(IV) sorption, synthesis of the alkylating agent, calculation of Kd values from Pu(IV) sorption results, and conclusions from the study of Pu(IV) sorption from 7M nitric acid by macroporous anion-exchange resins including level of crosslinking, level of alkylation, length of spacer, and bifunctional vs. monofunctional anion-exchange resins

  9. Purification of degraded TBP solvent using macroreticular anion exchange resin

    International Nuclear Information System (INIS)

    Tri-n-butyl phosphate (TBP) diluted with a suitable diluent is commonly used for solvent extraction in Purex process for the recovery of uranium and plutonium from irradiated nuclear fuels. This solvent gets degraded due to various factors, the main degradation product being dibutyl phosphoric acid (HDBP). A solvent cleanup step is generally incorporated in the process for removing the degradation products from the used solvent. A liquid-liquid cleanup system using sodium carbonate or sodium hydroxide solution is routinely used. Considering certain advantages, like the possibility of loading the resin almost to saturation capacity and the subsequent disposal of the spent resin by incineration and the feasibility of adopting it to the process, a liquid-solid system has been tried as an alternate method, employing various available macroreticular anion exchange resins in OH- form for the sorption of HDBP from TBP. After standardizing the various conditions for the satisfactory removal of HDBP from TBP using synthetic mixtures, resins were tested with process solvent in batch contacts. The parameters studied were (1) capacity of different resins for HDBP sorption (2) influence of acidity, uranium and HDBP on the sorption behaviour of the latter (3) removal of fission products from the solvent by the resin and (4) regeneration and recycling of the resin. (author). 2 figs., 13 tabs., 17 refs

  10. Anion-exchange sorption of molybdate and germanate

    Energy Technology Data Exchange (ETDEWEB)

    Kislinskaya, G.E.; Denisova, T.I.; Sheka, I.A.

    1983-07-20

    Interest in sorption of molybdenum and germanium from salt solutions is prompted by industrial requirements related to purification of such solutions and also to extraction of these elements from various industrial liquors.In order to identify the ionic forms of molybdenum and germanium having the highest sorption activity and to determine the optimal conditions for extraction of these elements from solutions with high electrolyte contents, we studied the states of molybdenum(VI) and germanium(IV) in solutions of sodium chloride in various concentrations, and sorption of these elements by strongly basic macroporous anion-exchange resins and by iron and aluminum hydroxides in relation to the pH, concentrations of the elements, and time of contact between the solution and the sorbent. Examination of literature data shows that the molecular and ionic states of these elements in the presence of high salt concentrations have been studied mainly in acidic solutions and at higher molybdenum and germanium concentrations. However, for selection of a method of removal of molybdenum and germanium from production liquors it is also necessary to have analogous information on their states when present in microconcentrations over wide ranges of pH.

  11. Anion-exchange sorption of molybdate and germanate

    International Nuclear Information System (INIS)

    Interest in sorption of molybdenum and germanium from salt solutions is prompted by industrial requirements related to purification of such solutions and also to extraction of these elements from various industrial liquors.In order to identify the ionic forms of molybdenum and germanium having the highest sorption activity and to determine the optimal conditions for extraction of these elements from solutions with high electrolyte contents, we studied the states of molybdenum(VI) and germanium(IV) in solutions of sodium chloride in various concentrations, and sorption of these elements by strongly basic macroporous anion-exchange resins and by iron and aluminum hydroxides in relation to the pH, concentrations of the elements, and time of contact between the solution and the sorbent. Examination of literature data shows that the molecular and ionic states of these elements in the presence of high salt concentrations have been studied mainly in acidic solutions and at higher molybdenum and germanium concentrations. However, for selection of a method of removal of molybdenum and germanium from production liquors it is also necessary to have analogous information on their states when present in microconcentrations over wide ranges of pH

  12. Anion-exchange separations of metal ions in thiocyanate media.

    Science.gov (United States)

    Fritz, J S; Kaminski, E E

    1971-05-01

    The analytical potential of a weak-base macroreticular anion-exchange resin for the quantitative separation of metal ions in thiocyanate media is investigated and demonstrated. Distribution data are given for the sorption of some 25 metal ions from aqueous mixtures of potassium thiocyanate (1.0M or less) and 0.5M hydrochloric acid. The magnitude of the distribution data suggests many possible separations, some of which were quantitatively performed by procedures which are fast, simple and require only mild conditions. Representative separations are removal of traces of iron(III) and copper(II) from water samples prior to the determination of water hardness (calcium and magnesium), separation of nickel(II) from vanadium(IV) and the separation of thorium(IV) from titanium(IV). Some multicomponent separations are the separation of rare earths(III) and thorium(IV) from scandium(III) and the separation of rare earths(III) from iron(III) and uranium(VI). PMID:18960914

  13. Fouling mitigation of anion exchange membrane by zeta potential control.

    Science.gov (United States)

    Park, Jin-Soo; Lee, Hong-Joo; Choi, Seok-Ju; Geckeler, Kurt E; Cho, Jaeweon; Moon, Seung-Hyeon

    2003-03-15

    The feasibility of fouling mitigation of anion exchange membranes (AEMs) in the presence of humate was studied by adding three different types of water-soluble polymers, i.e., poly(acrylic acid) (PAA), poly(vinyl alcohol) (PVA), and poly(ethylene imine) (PEI), during electrodialysis (ED) desalination. Measurement of zeta potential of the humate used in this study showed highly negative potential (about -30 mV), implying that the humate had a strong fouling potential on the AEMs in ED. Of the three water-soluble polymers, PEI showed a positive zeta potential (about +14 mV) and is able to form an interpolymer complex with the humate. PAA and PVA hardly formed interpolymer complexes with humate due to electrostatic repulsion. The PEI-humate mixture with a volume ratio of 1:20 (PEI:humate) showed zero zeta potential, and a complexed humate with zero surface charge was formed, resulting in no fouling effects on the AEMs. Accordingly, the desalting ED experiments with PEI showed improved ED performance. Further, black colloids formed in the mixture did not cause the cell resistance to increase. PMID:16256509

  14. Highly conductive side chain block copolymer anion exchange membranes.

    Science.gov (United States)

    Wang, Lizhu; Hickner, Michael A

    2016-06-28

    Block copolymers based on poly(styrene) having pendent trimethyl styrenylbutyl ammonium (with four carbon ring-ionic group alkyl linkers) or benzyltrimethyl ammonium groups with a methylene bridge between the ring and ionic group were synthesized by reversible addition-fragmentation radical (RAFT) polymerization as anion exchange membranes (AEMs). The C4 side chain polymer showed a 17% increase in Cl(-) conductivity of 33.7 mS cm(-1) compared to the benzyltrimethyl ammonium sample (28.9 mS cm(-1)) under the same conditions (IEC = 3.20 meq. g(-1), hydration number, λ = ∼7.0, cast from DMF/1-propanol (v/v = 3 : 1), relative humidity = 95%). As confirmed by small angle X-ray scattering (SAXS), the side chain block copolymers with tethered ammonium cations showed well-defined lamellar morphologies and a significant reduction in interdomain spacing compared to benzyltrimethyl ammonium containing block copolymers. The chemical stabilities of the block copolymers were evaluated under severe, accelerated conditions, and degradation was observed by (1)H NMR. The block copolymer with C4 side chain trimethyl styrenylbutyl ammonium motifs displayed slightly improved stability compared to that of a benzyltrimethyl ammonium-based AEM at 80 °C in 1 M NaOD aqueous solution for 30 days. PMID:27216558

  15. Anion exchange purification of plasmid DNA using expanded bed adsorption.

    Science.gov (United States)

    Ferreira, G N; Cabral, J M; Prazeres, D M

    2000-01-01

    Recent developments in gene therapy with non-viral vectors and DNA vaccination have increased the demand for large amounts of pharmaceutical-grade plasmid DNA. The high viscosity of process streams is of major concern in the purification of plasmids, since it can cause high back pressures in column operations, thus limiting the throughput. In order to avoid these high back pressures, expanded bed anion exchange chromatography was evaluated as an alternative to fixed bed chromatography. A Streamline 25 column filled with 100 ml of Streamline QXL media, was equilibrated with 0.5 M NaCl in TE (10 mM Tris, 1 mM EDTA, pH = 8.0) buffer at an upward flow of 300 cmh-1, E. coli lysates (obtained from up to 3 liters of fermentation broth) were injected in the column. After washing out the unbound material, the media was allowed to sediment and the plasmid was eluted with 1 M NaCl in TE buffer at a downward flow of 120 cmh-1. Purification factors of 36 +/- 1 fold, 26 +/- 0.4 plasmid purity, and close to 100% yields were obtained when less than one settled column volume of plasmid feed was injected. However, both recovery yield and purity abruptly decreased when larger amounts were processed-values of 35 +/- 2 and 5 +/- 0.7 were obtained for the recovery yield and purity, respectively, when 250 ml of feedstock were processed. In these cases, gel clogging and expansion collapse were observed. The processing of larger volumes, thus larger plasmid quantities, was only possible by performing an isopropanol precipitation step prior to the chromatographic step. This step led to an enhancement of the purification step. PMID:10840595

  16. Ionic Resistance and Permselectivity Tradeoffs in Anion Exchange Membranes

    KAUST Repository

    Geise, Geoffrey M.

    2013-10-23

    Salinity gradient energy technologies, such as reverse electrodialysis (RED) and capacitive mixing based on Donnan potential (Capmix CDP), could help address the global need for noncarbon-based energy. Anion exchange membranes (AEMs) are a key component in these systems, and improved AEMs are needed in order to optimize and extend salinity gradient energy technologies. We measured ionic resistance and permselectivity properties of quaternary ammonium-functionalized AEMs based on poly(sulfone) and poly(phenylene oxide) polymer backbones and developed structure-property relationships between the transport properties and the water content and fixed charge concentration of the membranes. Ion transport and ion exclusion properties depend on the volume fraction of water in the polymer membrane, and the chemical nature of the polymer itself can influence fine-tuning of the transport properties to obtain membranes with other useful properties, such as chemical and dimensional stability. The ionic resistance of the AEMs considered in this study decreased by more than 3 orders of magnitude (i.e., from 3900 to 1.6 Ω m) and the permselectivity decreased by 6% (i.e., from 0.91 to 0.85) as the volume fraction of water in the polymer was varied by a factor of 3.8 (i.e., from 0.1 to 0.38). Water content was used to rationalize a tradeoff relationship between the permselectivity and ionic resistance of these AEMs whereby polymers with higher water content tend to have lower ionic resistance and lower permselectivity. The correlation of ion transport properties with water volume fraction and fixed charge concentration is discussed with emphasis on the importance of considering water volume fraction when interpreting ion transport data. © 2013 American Chemical Society.

  17. Anion exchange resin as support for invertase immobilization

    Directory of Open Access Journals (Sweden)

    M. Vitolo

    2009-01-01

    Full Text Available

    The invertase (EC 3.2.1.26 from Saccharomyces cerevisiae was employed as a model enzyme in the evaluation of the adsorption capacity of DOWEX-1X8-50®, a basic anion exchange resin, when used as support in enzyme immobilization. By mixing 100mg of resin with 27mg of invertase (pI = 4.0 in buffer solution (pH 4.6, 25°C, stirred at 100rpm, an adsorption of 93% was achieved. The activities (1U = amount of enzyme forming 1mg reducing sugars/min of soluble and insoluble invertase were 0.084 U/mgE and 0.075 U/mgE, respectively, giving an immobilization coefficient of 90.4%. The immobilized invertase had a higher thermal stability than the soluble form. The highest activity was observed at pH 4.5 in both forms of the enzyme, whereas the pH stability ranges for soluble and insoluble invertase were 3.5-5.0 and 4.5-5.5, respectively. The kinetic constants for soluble invertase were KM = 18.3 mM and Vmax = 0.084 U/mgE, and for the insoluble form, KM = 29.1 mM and Vmax = 0.075 U/mgE. The resin tested adsorbed the invertase very well, provided the enzyme molecule had a net negative charge, i.e., the immobilization and reaction procedures had to be carried out at pH > pI. Keywords: Invertase, immobilization, adsorption, anionexchange resin.

  18. Nanostructure-controlled anion exchange membranes for fuel cell applications by high-energy heavy-ion irradiation. Preparation and characterization of anion exchange membranes

    International Nuclear Information System (INIS)

    Heavy ions at kinetic energies typically from several hundreds of MeV to a few GeV passing through a polymer substrate induce a continuous trail of excitations and ionizations called latent tracks. We used a direct ion-track grafting method for preparation of anion exchange membranes for fuel cells. The functional anion exchange groups were introduced inside the latent tracks, thereby achieving OH--conductive channels through the thickness. These straight channels increased conductivities, while the isolated cylindrical structure of tracks restricted the water uptake. (author)

  19. Preparation of a chitosan-based anionic exchanger for removal of bromide, chloride, iodide and phosphate ions from aqueous solutions

    Directory of Open Access Journals (Sweden)

    Affonso Celso Gonçalves Júnior

    2014-02-01

    Full Text Available The development of a chitosan anion exchanger, obtained from shrimp shells, and its adsorption capacity for chloride, bromide, iodide and phosphate anions are provided. Dependence of exchange processes with the anions as a function of pH and contact time between exchanger and anions were initially investigated. Results showed that the best adsorption of ions occurred at pH 3.0. Exchange isotherms were then developed by the Langmuir, Freundlich and Dubinin-Radushkevich mathematical models. Results demonstrated that chitosan produced from shrimp shells may be used as feedstock in the manufacture of anion exchange microspheres.

  20. Separation of bivalent anti-T cell immunotoxin from Pichia pastoris glycoproteins by borate anion exchange.

    Science.gov (United States)

    Woo, Jung Hee; Neville, David M

    2003-08-01

    A major problem encountered in the large-scale purification of the bivalent anti-T cell immunotoxin, A-dmDT390-bisFv(G4S), from Pichia pastoris supernatants was the presence of host glycoproteins exhibiting similar charge, size, and hydrophobicity characteristics. We overcame this problem by employing borate anion exchange chromatography. The borate anion has an affinity for carbohydrates and imparts negative charges to these structures. We found that at a concentration of sodium borate between 50 and 100 mM, the nonglycosylated immunotoxin did not bind to Poros 50 HQ anion exchanger resin, but glycoproteins, including aggregates related to the immunotoxin, did. By using this property of the immunotoxin in the presence of sodium borate, we successfully developed a 3-step purification procedure: (i) Butyl-650M hydrophobic interaction chromatography, (ii) Poros 50 HQ anion exchange chromatography in the presence of borate, and (iii) HiTrap Q anion exchange chromatography. The final preparation exhibited a purity of greater than 98% and a yield of greater than 50% from the supernatant. Previously, boronic acid resins have been used to separate glycoproteins from proteins. However, combining borate anion with conventional anion exchange resins accomplishes the separation of the immunotoxin from glycoproteins and eliminates the need to evaluate nonstandard resins with respect to good manufacturing practice guidelines. PMID:12951782

  1. Removal of plutonium from nitric acid-oxalic acid solutions using anion exchange method

    International Nuclear Information System (INIS)

    An anion exchange method using Amberlyst A-26 (MP) resin was developed for removal of Pu from nitric acid-oxalic acid solutions without destroying oxalate. The method consists of sorption of Pu(IV) on Amberlyst A-26, a macroporous anion exchange resin, from nitric acid-oxalic acid medium in the presence of Al(NO3)3. Pu(IV) breakthrough capacity of Amberlyst A-26 using synthetic feed solution was determined. (author)

  2. Separation of boron isotopes by ion exchange chromatography: studies on regeneration of strong base anion exchange resins

    International Nuclear Information System (INIS)

    The optimum conditions for the regeneration of strong base anion exchange resins of type-I and type-II were determined for cost-effective separation of isotopes of boron by ion exchange chromatography where the hydroxyl form of an anion exchange resin is equilibrated with boric acid solution containing mannitol as a complexing reagent. The possibility of using unspent alkali content of the effluent was also exploited. Removal of carbonate impurity from Rayon grade caustic lye (used as regenerant after dilution) and recycling of Ba(OH)2 was studied to avoid waste disposal problems. (author)

  3. Anion-Exchange Properties of Trifluoroacetate and Triflate Salts of N-Alkylammonium Resorcinarenes.

    Science.gov (United States)

    Pan, Fangfang; Beyeh, Ngong Kodiah; Bertella, Stefania; Rissanen, Kari

    2016-03-01

    The synthesis of N-benzyl- and N-cyclohexylammonium resorcinarene trifluoroacetate (TFA) and triflate (OTf) salt receptors was investigated. Solid-state analysis by single-crystal X-ray diffraction revealed that the N-alkylammonium resorcinarene salts (NARSs) with different upper substituents had different cavity sizes and different affinities for anions. Anion-exchange experiments by mixing equimolar amounts of N-benzylammonium resorcinarene trifluoroacetate and N-cyclohexylammonium resorcinarene triflate, as well as N-benzylammonium resorcinarene triflate and N-cyclohexylammonium resorcinarene trifluoroacetate showed that the NARS with flexible benzyl groups preferred the larger OTf anion, whereas the rigid cyclohexyl groups preferred the smaller TFA anions. The anion-exchange processes were confirmed in the solid state by single-crystal and powder X-ray diffraction experiments and in the gas phase by electrospray ionization mass spectrometry. PMID:26749383

  4. Boron isotope separation by ion exchange chromatography using weakly basic anion exchange resin

    International Nuclear Information System (INIS)

    Isotopic plateau displacement chromatography, a useful method for isotope separation is presented. The boric acid band formed in a column of weakly basic anion exchange resin Diaion WA21 can be eluted with pure water. In order to obtain good accumulation of the isotope effect, a series of experiments with different migration length were carried out. The boron-10 enriched part of the boric acid absorbed band was always preceded by the isotopic plateau part, in which the atomic fraction of boron-10 was maintained at its original value. The atomic fraction of boron-10 at the end of the chromatogram increased with migration length, and in the case of 256-m migration, boron-10 was enriched from its original atomic fraction of 19.84 to 91.00%, the separation factor S being constant irrespective of migration length: S = 1.0100 +- 0.0005. (author)

  5. Anion exchange sorption of molybdate and germanate from salt solutions

    Energy Technology Data Exchange (ETDEWEB)

    Kislinskaya, G.E.; Denisova, T.I.; Sheka, I.A. (AN Ukrainskoj SSR, Kiev. Inst. Obshchej i Neorganicheskoj Khimii)

    1983-02-01

    A study has been made of the state of Mo(6) and Ge(4) in solutions containing various concentrations (5-300 g/l) of HCl and their sorption with highly-alkaline macroporous anionites (Duolite 101 D, ChFO, AM, AMP) and hydroxides of iron and aluminium, depending on pH value, element concentration and time of solution contact with sorbent. Polymer anions of molybdate with a sorption maximum at pH=1-3 and monomer anions of germanate at pH>8 are found to be the most active forms of molybdenum and germanium, as to their sorption, at their concentrations of 10/sup -6/-10/sup -5/g-atom/l in sodium chloride solutions. Regions of molybdate and germanate effective sorption with anionites and hydroxides of iron and aluminium in electrolyte solutions get narrower, as compared with aqueous solutions, due to competing sorption of a background electrolyte anion.

  6. Absence of transepithelial anion exchange by rabbit OMCD: Evidence against reversal of cell polarity

    International Nuclear Information System (INIS)

    In the rabbit cortical collecting duct (CCD), Cl tracer crosses the epithelium predominantly via an anion exchange system that operates in either a Cl-Cl or Cl-HCO3 exchange mode. In the present study, the authors used the 36Cl lumen-to-bath rate coefficient (KCl, nm/s), a sensitive measurement of CCD transepithelial anion transport, to investigate the nature of Cl transport in the medullary collecting duct dissected from inner stripe, outer medulla (OMCD). The KCl in OMCD perfused and bathed in HCO3-Ringer solution was low and similar to that value observed in the CCD when anion exchange is inhibited and Cl permeates the epithelium by diffusion. To test the hypothesis that metabolic alkalosis could reverse the polarity of intercalated cells and thus induce an apical Cl-HCO3 exchanger in H+-secreting OMCD cells, they measured KCl in OMCD from rabbits make alkalotic by deoxycorticosterone and furosemide. Although the base-line KCl was slightly higher than in OMCD from control rabbits, the value was still far lower than the KCl under comparable conditions in CCD. They conclude (1) Cl transport across the MCD by anion exchange is immeasurably low or nonexistent; (2) unlike the CCD, Cl transport in OMCD is not responsive to cAMP; and (3) metabolic alkalosis does not induce an apical anion exchanger in OMCD, i.e., does not cause epithelial polarity reversal

  7. A new anionic exchange stir bar sorptive extraction coating based on monolithic material for the extraction of inorganic anion.

    Science.gov (United States)

    Huang, Xiaojia; Lin, Jianbing; Yuan, Dongxing

    2010-07-23

    A novel anionic exchange stir bar sorptive extraction (SBSE) coating based on poly(2-(methacryloyloxy)ethyltrimethylammonium chloride-co-divinylbenzene) monolithic material for the extraction of inorganic anion was prepared. The effect of preparation conditions such as ratio of functional monomer to cross-linker, content of porogenic solvent on the extraction efficiencies were investigated in detailed. The monolithic material was characterized by elemental analysis, scanning electron microscopy and infrared spectroscopy. In order to investigate the extraction capacity of the new coating for inorganic anion, the new SBSE was combined with ionic chromatography with conductivity detection, Br-, NO3-, PO4(3-) and SO4(2-) were selected as detected solutes. Several extractive parameters, including pH value and ionic strength in sample matrix, desorption solvent, extraction and desorption time were optimized. The results showed that strongly ionic strength did not favor the extraction of anlaytes. Under the optimum experimental conditions, low detection limits (S/N=3) and quantification limits (S/N=10) of the proposed method for the target anions were achieved within the range of 0.92-2.62 and 3.03-9.25 microg/L, respectively. The method also showed good linearity, simplicity, practicality and low cost for the extraction inorganic anions. Finally, the proposed method was successfully used to detect the two different trademarks of commercial purified water with satisfactory recovery in the range of 70.0-92.6%. To the best of our knowledge, this is the first to use SBSE to enrich inorganic anions. PMID:20576270

  8. Significance of anion exchange in pentachlorophenol sorption by variable-charge soils.

    Science.gov (United States)

    Hyun, Seunghun; Lee, Linda S; Rao, P Suresh C

    2003-01-01

    Sorption data and subsequent predictive models for evaluating acidic pesticide behavior on variable-charge soils are needed to improve pesticide management and environmental stewardship. Previous work demonstrated that sorption of pentachlorophenol (PCP), a model organic acid, was adequately modeled by accounting for pH-and pKa-dependent chemical speciation and using two organic carbon-normalized sorption coefficients; one each for the neutral and anionic species. Such models do not account for organic anion interaction to positively charged surface sites, which can be significant for variable-charge minerals present in weathered soils typical of tropical and subtropical regions. The role of anion exchange in sorption of ionizable chemicals by variable-charge soils was assessed by measuring sorption of PCP by several variable-charge soils from aqueous solutions of CaCl2, CaSO4, Ca(H2PO4)2 as a function of pH. Differences in sorption from phosphate and chloride electrolyte solutions were attributed to pentachlorophenolate interactions with anion exchange sites. Suppression of PCP sorption by phosphate ranged from negligible in a soil with essentially no positively charge sites, as measured by negligible anion exchange capacity, to as much as 69% for variable-charge soils. Pentachlorophenolate exchange correlated well with the ratio of pH-dependent anion exchange capacity to net surface charge. Sorption reversibility of PCP by both CaCl2 and Ca(H2PO4)2 solutions was also demonstrated. Results for PCP clearly demonstrate that sorption to anion exchange sites in variable-charge soils should be considered in assessing pesticide mobility and that phosphate fertilizer application may increase the mobility of acidic pesticides. PMID:12809297

  9. Models for the estimation of thermodynamic properties of layered double hydroxides: application to the study of their anion exchange characteristics

    Directory of Open Access Journals (Sweden)

    Bravo-Suárez Juan J.

    2004-01-01

    Full Text Available Several models for the estimation of thermodynamic properties of layered double hydroxides (LDHs are presented. The predicted thermodynamic quantities calculated by the proposed models agree with experimental thermodynamic data. A thermodynamic study of the anion exchange process on LDHs is also made using the described models. Tables for the prediction of monovalent anion exchange selectivities on LDHs are provided. Reasonable agreement is found between the predicted and the experimental monovalent anion exchange selectivities.

  10. Separation of metal ions by anion exchange in mixtures of hydrochloric acid and hydrofluoric acid

    Energy Technology Data Exchange (ETDEWEB)

    Faris, J.P.

    1978-12-01

    Distribution coefficients were determined for the adsorption of more than 40 elements on anion-exchange resins from mixtures of HCl (0.1 to 12M) and HF (0.1-8M). Two resins, Dowex 1 x 10, 200 to 400 mesh and Dowex 1 x 4, 100 to 200 mesh, were used. Distribution coefficients were also determined for the adsorption of many elements on both resins from 0.1 to 12M HCl and 0.1 to 12M HF. Anion exchange in the presence of HF was found useful for separating impurities from various materials for their subsequent determination, and specific procedures used in our spectrochemical laboratory for this purpose are outlined. The results of a literature search on the use of anion exchange in hydrofluoric acid and fluoride-containing media are presented in an extensive bibliography. 404 references, 9 tables.

  11. Separation of metal ions by anion exchange in mixtures of hydrochloric acid and hydrofluoric acid

    International Nuclear Information System (INIS)

    Distribution coefficients were determined for the adsorption of more than 40 elements on anion-exchange resins from mixtures of HCl (0.1 to 12M) and HF (0.1-8M). Two resins, Dowex 1 x 10, 200 to 400 mesh and Dowex 1 x 4, 100 to 200 mesh, were used. Distribution coefficients were also determined for the adsorption of many elements on both resins from 0.1 to 12M HCl and 0.1 to 12M HF. Anion exchange in the presence of HF was found useful for separating impurities from various materials for their subsequent determination, and specific procedures used in our spectrochemical laboratory for this purpose are outlined. The results of a literature search on the use of anion exchange in hydrofluoric acid and fluoride-containing media are presented in an extensive bibliography. 404 references, 9 tables

  12. Nanocomposite membranes based on quaternized polysulfone and functionalized montmorillonite for anion-exchange membranes

    Science.gov (United States)

    Liao, Xiaofeng; Ren, Li; Chen, Dongzhi; Liu, Xiaohong; Zhang, Hongwei

    2015-07-01

    In this paper, functionalized montmorillonite is intercalated with cetyl trimethyl ammonium chloride and (3-aminopropyl)triethoxysilane. Quaternized polysulfone/functionalized montmorillonite nanocomposite membranes are fabricated to evaluate their potential in anion-exchange membrane fuel cells. Fourier transform infrared spectroscopy, thermogravimetric analyzer and X-ray diffractometer are used to confirm the success of intercalation. The performances of the composite membranes for the anion-exchange membrane fuel cells in terms of their water uptake, mechanical property and ionic conductivity are investigated. Compared with other anion-exchange membranes, the nanocomposite membrane containing 5% montmorillonite modified by cetyl trimethyl ammonium chloride exhibits lower water uptake, higher ultimate stress and larger ionic conductivity. It exhibits an ionic conductivity of 4.73 × 10-2 S cm-1 at 95 °C.

  13. Anion-exchange Studies of Radioactive Trace Elements in Sulphuric Acid Solutions

    International Nuclear Information System (INIS)

    As part of a chemical group separation procedure used as a pretreatment in gamma spectrometric analysis, a study has been made of the adsorption from sulphuric acid solutions on strongly basic anion exchange resins, prepared in the hydroxide and the sulphate forms, of trace activities of Na, P, K, Ca, Sc, Cr, Mn, Fe, Co, Ni, Cu, Zn, Ga, Rb, Sr, Zr, Nb, Mo, Tc, Ag, Cd, In, Cs, Ba, La, Ce, Hf, Ta, W, Ir, Pa and Np. Besides adsorbing some of the trace elements in the solution, the anion exchange resin in the hydroxide form will neutralize the bulk of the sulphuric acid. This makes possible the subsequent sequential separation of chloride complexes on short anion-exchange columns by a stepwise increasing of the HCl concentration of the solution. On the basis of the results obtained in the present and earlier experiments, a new improved chemical group-separation procedure for mixtures of radioactive trace elements is outlined

  14. Adsorption of U(VI) from HCl solutions on anion exchange resins

    International Nuclear Information System (INIS)

    Full text: The adsorption capacity of different commercial exchange resins, such as: Amberlite-RA 900 Cl; Amberjet 4400 Cl; Dowex 1-X8; Dowex-Marathon and CEPU-5M (synthesized specially for uranium isotope exchange), for uranyl chlorocomplexes in HCl solutions was determined. The measurements were performed at different temperatures and HCl solution concentrations using two contact methods for solution-resin system, namely through chromatography on column and batch operation. For anion exchange resins as Amberlite-IRA 900 Cl, Dowex 1-X8 and Dowex-Marathon, the uranium adsorption capacities increased with HCl concentrations and contact temperatures. The same behaviour was observed for anion exchange strong basic resin CEPU-5M, synthesized specially for uranium isotope exchange. Uranyl chlorocomplex molecule adsorbed on resin is [UO2Cl3]-, as determined by batch operation from uranium adsorption capacities of Dowex-Marathon. (author)

  15. Preparation and chromatographic performance of polymer-based anion exchangers for ion chromatography: A review.

    Science.gov (United States)

    Zatirakha, A V; Smolenkov, A D; Shpigun, O A

    2016-01-21

    In the last decade the developments in the field of ion chromatography (IC) were aimed at increasing the efficiency, sensitivity and rapidity of analysis, as well as on improving separation selectivity. Since selectivity and efficiency to the large extent depend on the surface chemistry of the stationary phase, the development of novel anion exchangers remains one of the priority tasks in modern IC. The exact chemistry of commercially available resins is not known and not many literature data devoted to the procedures of preparing anion exchangers for IC have become available in the last 10-15 years. However, the knowledge about the surface chemistry of anion exchangers can provide understanding of the trends in selectivity and efficiency changes, as well as help with the choice of the stationary phase type suitable for solving a particular analytical task. The current review is devoted to the methods of preparing anion exchangers based on polystyrene-divinylbenzene (PS-DVB) and ethylvinylbenzene-divinylbenzene (EVB-DVB) for IC of inorganic and small organic anions and is aimed at demonstrating the improvement of their performance over the years, which was brought by the development of the new types of stationary phase architecture. PMID:26724761

  16. Modified anion-exchange method for determination of thorium in uranium based materials

    International Nuclear Information System (INIS)

    This paper details a modified anion-exchange method for estimation of thorium in uranium based samples like uranium dioxide powders, pellets and uranyl nitrate solutions. The method involves separation of thorium from uranium from 3M commercial grade HCl containing 15% NaCl through an anion-exchange resin. The uranium free effluent containing the analyte(thorium) is determined spectrophotometrically by exploiting absorption of the thorium-arsenazo III complex at 660 nm. The method has a precision of about ±2% at 50 ppm level. (author). 3 refs., 1 tab

  17. Impact of powdered activated carbon and anion exchange resin on photocatalytic treatment of textile wastewater

    OpenAIRE

    Dhas, Preethi Grace Theva Neethi; Gulyas, Holger; Otterpohl, Ralf

    2015-01-01

    In order to clarify the impact of activated carbon and anion exchange resin on photocatalytic oxidation (PCO) of textile industry wastewater, TiO2-based PCO was investigated with aqueous solutions containing the reactive dye Reactive Blue 4 (RB4) and with a textile dye house effluent in the absence and in the presence of powdered activated carbon (PAC) and the anion exchange resin Lewatit MP 500. Addition of Lewatit improved RB4 removal to a larger extent than PAC addition. Contrasting to chl...

  18. Anion exchange pathways for Cl- transport in rabbit renal microvillus membranes

    International Nuclear Information System (INIS)

    The authors evaluated the mechanisms of chloride transport in microvillus membrane vesicles isolated from the rabbit renal cortex. The presence of Cl-formate exchange was confirmed. Outward gradients of oxaloacetate, HCO3, acetate, lactate, succinate, sulfate, and p-aminohippurate (PAH) stimulated the rate of Cl uptake minimally or not at all. However, an outward gradient of oxalate stimulated Cl uptake by 70%, and an outward Cl gradient induced uphill oxalate uptake, indicting Cl-oxalate exchange. Moreover, an outward formate gradient induced uphill oxalate uptake, indicating formate-oxalate exchange. Studies of inhibitor and substrate specificity indicated the probably operation of at least two separate anion exchangers in mediating Cl transport. The Cl-formate exchanger accepted Cl and formate as substrates, had little or no affinity for oxalate, was sensitive to inhibition by furosemide, and was less sensitive to inhibition by 4,4'-diisothiocyanostilbene-2,2'-disulfonic acid (DIDS). The Cl (formate)-oxalate exchanger also accepted Cl and formate as substrates but had high affinity for oxalate, was highly sensitive to inhibition by DIDS, and was less sensitive to inhibition by furosemide. The Cl-formate exchanger was electroneutral, whereas the Cl (formate)-oxalate exchanger was electrogenic. They conclude that at least separate anion exchangers mediating Cl transport are present on the luminal membrane of the rabbit proximal tubule cell. These exchangers may play important roles in mediating transtubular Cl and oxalate transport in this nephron segment

  19. Use of type-II strong base anion exchange resins for ion exchange chromatographic separation of isotopes of boron

    International Nuclear Information System (INIS)

    The optimum conditions for the regeneration of strong base anion exchange resins of type-I and type-II were determined for cost - effective separation of isotopes of boron by ion exchange chromatography. The possibility of using unspent alkali content of the effluent was also exploited. Removal of carbonate impurity from rayon grade caustic lye (used as regenerant after dilution) and recycling of Ba(OH)2 was studied to avoid waste disposal problems. The determination of (i) ion exchange capacity of Duolite-162 resin for hydroxyl - chloride and hydroxyl - borate exchanges, (ii) isotopic exchange separation factor by batch method and (iii) effect of concentration of boric acid (in presence and absence of mannitol) on isotopic exchange separation factor to test the suitability of the type-II resin for this process are discussed. (author)

  20. Adsorption Mechanisms of Heavy Metal Ions from Drinking Water by Weakly Basic Anion Exchange Resins

    Institute of Scientific and Technical Information of China (English)

    赵璇; 何仕均; 杨磊

    2002-01-01

    Heavy metal micro-contaminants can be removed from water sources technologies. Weakly basic anion exchange resins offer the best ability to remove trace amounts of heavy metals with high selectivity. This paper discusses how weakly basic resins adsorb heavy metals using two different approaches. The removal of mercury, cadmium, and lead ions is based on the fundamental theory of coordination chemistry. The mechanism is not ion exchange but extractive adsorption of heavy metal salts. However, the marked preferential adsorption of chromate by weakly basic anion exchange can be explained using the traditional theory of ion exchange. A lab-scale study produced positive results for the removal of trace amounts of heavy metal ions from drinking water.

  1. New anion-exchange resins for improved separations of nuclear materials. Mid-year progress report

    International Nuclear Information System (INIS)

    'The authors are developing multi-functional anion-exchange resins that facilitate anion uptake by carefully controlling the structure of the anion receptor site. The new ion-exchange resins interface the rapidly developing field of ion-specific chelating ligands with robust, commercial ion exchange technology. The overall objective of the research is to develop a predictive capability which allows the facile design and implementation of multi-functionalized anion exchange materials which selectively sorb metal complexes of interest from targeted process, waste, and environmental streams. The basic scientific issues addressed are actinide complex speciation along with modeling of the metal complex/functional site interactions in order to determine optimal binding-site characteristics. Their approach uses a thorough determination of the chemical species both in solution and as bound to the resin to determine the characteristics of resin active sites which can actively facilitate specific metal-complex sorption to the resin. The first year milestones were designed to allow us to build off of their extensive expertise with plutonium in nitrate solutions prior to investigating other, less familiar systems. While the principle investigators have successfully developed actinide chelators and ion-exchange materials in the past, the authors were fully aware that integration of this two fields would be challenging, rewarding and, at times, highly frustrating. Relatively small differences in the substrate (cross-linkage, impurities), the active sites (percent substitution, physical accessibility), the actinide solution (oxidation state changes, purity) and the analytical procedures (low detection limits) can produce inconsistent sorption behavior which is difficult to interpret. The potential paybacks for success, however, are enormous. They feel that they have learned a great deal about how to control these numerous variables to produce consistent, reliable analysis of

  2. Test procedure for anion exchange testing with Argonne 10-L solutions

    International Nuclear Information System (INIS)

    Four anion exchange resins will be tested to confirm that they will sorb and release plutonium from/to the appropriate solutions in the presence of other cations. Certain cations need to be removed from the test solutions to minimize adverse behavior in other processing equipment. The ion exchange resins will be tested using old laboratory solutions from Argonne National Laboratory; results will be compared to results from other similar processes for application to all plutonium solutions stored in the Plutonium Finishing Plant

  3. Separation and determination of alditols and sugars by high-pH anion-exchange chromatography with pulsed amperometric detection

    DEFF Research Database (Denmark)

    Andersen, Rikke; Sørensen, A.

    Carbohydrates such as alditols (polyols or sugar alcohols), monosaccharides and disaccharides are separated as anions by anion-exchange chromatography with a sodium hydroxide eluent, MA1 CarboPac column and pulsed amperometric detection. We report a high-pH anion-exchange chromatographic-pulsed a......Carbohydrates such as alditols (polyols or sugar alcohols), monosaccharides and disaccharides are separated as anions by anion-exchange chromatography with a sodium hydroxide eluent, MA1 CarboPac column and pulsed amperometric detection. We report a high-pH anion-exchange chromatographic......-pulsed amperometric detection (HPAEC-PAD) method that determines all the polyols used as food additives in food products and the most commonly found mono- and disaccharides on a routine basis. The linearity, repeatability, internal reproducibility and accuracy are described. The applicability of the method has been...

  4. Determination of the ion-exchange capacity of anion-selective membranes

    Czech Academy of Sciences Publication Activity Database

    Karas, F.; Hnát, J.; Paidar, M.; Schauer, Jan; Bouzek, K.

    2014-01-01

    Roč. 39, č. 10 (2014), s. 5054-5062. ISSN 0360-3199 Institutional support: RVO:61389013 Keywords : ion-exchange capacity * anion-selective membranes * titration Subject RIV: CD - Macromolecular Chemistry Impact factor: 3.313, year: 2014

  5. Studies concerning the anion ex-change resins catalyzed esterification of epichlorohydrin with organic acids

    Directory of Open Access Journals (Sweden)

    E.I. Muresan

    2009-09-01

    Full Text Available The paper studies the esterification of carboxylic acids with epichlorohydrin over two macroporous strong base anion exchange resins with different polymer matrix. For both resins, the influence of reaction parameters (temperature, catalyst loading, molar ratio on the reaction rate and the yields of the two isomeric esters were investigated.

  6. Investigation of an anion exchange resin for cleanup of a coolant used to machine nuclear materials

    International Nuclear Information System (INIS)

    This article describes the interaction of Dowex SBR-P, which is a strongly basic anion exchange resin, with ions found in a used machining coolant. The coolant is used in machining enriched uranium and contains uranium, chloride, nitrite, borate ions, water, and propylene glycol

  7. Separation of the rare earths by anion-exchange in the presence of lactic acid

    Science.gov (United States)

    Faris, J. P.

    1969-01-01

    Investigation of adsorption of rare earths and a few other elements to an anion-exchange resin from mixed solvents containing lactic acid shows that the lanthanides are absorbed more strongly than from the alpha-hydroxyisobutryric acid system, but with less separation between adjacent members of the series.

  8. Strong basic anion exchangers with adsorption properties for chlorocomplex uranyl ion

    International Nuclear Information System (INIS)

    Full text: Styrene-divinylbenzene copolymers (S-DVB) are still the most commonly used as starting copolymers in the synthesis of ion exchangers with special destinations, such as the enrichment process of 235U due to their high chemical resistance. For this purpose, a special concern has been lately focused on the preparation of macroporous strong basic anion exchangers containing one or two hydroxyalkyl substituents. An average pore radius around 1000 A, which is correlated with a high permanent porosity, a good stability of the resin in HCl with concentrations up to 8 N, a thermal resistance up to 150 deg C at least and a high mechanical strength are the main characteristics requested for this purpose. In a previous work we have reported the preparation of some macroporous S-DVB copolymers with sizes in the range 90-200 μm by employing 2-ethyl-1-hexanol as a porogen, at a high dilution of monomers (D ≥ 0.55) and their subsequent transformation in macroporous strong basic anion exchangers with an average pore radius higher than 50 nm. In the present study, the characteristics of the starting S-DVB macroporous copolymers synthesized in the presence of N-butyl alcohol (nBA) as porogen and those of the strong basic anion exchangers derived therefrom have been studied. Activation by chloromethylation reaction of the macroporous S-DVB copolymers was performed with paraformaldehyde (CH2O)n/trimethylchlorosilane (TMCS) in the presence of FeCl3 as catalyst, in chloroform as a reaction medium. Strong basic anion exchangers with diethyl 2-hydroxyethyl benzylammonium groups were obtained by the amination of the chloromethylated S-DVB copolymers with diethyl 2-hydroxyethylamine (DEHEA). The corresponding strong basic anion exchangers showed an ionic exchange capacity in the range 1.8-2.2 meq/g, depending on the crosslinking degree and the dilution of the starting copolymer, and an average pore radius, rp, around 80 nm. Such characteristics make these resins promising

  9. M8L12 cubic cages with all facial Δ or facial Λ configuration: effects of surface anions on the occupancy of the cage and anion exchange.

    Science.gov (United States)

    Yang, Jing; Chang, Xiao-Yong; Sham, Kiu-Chor; Yiu, Shek-Man; Kwong, Hoi-Lun; Che, Chi-Ming

    2016-05-21

    M8L12 cubic cages (M = Mn(II), Zn(II) or Cd(II)), with all eight metal ions having all facial Δ or facial Λ configurations and having an encapsulated anion, were prepared by the self-assembly of m-xylene-bridged imidazolyl-imine ligands and MX2 (X = PF6(-), SbF6(-), TfO(-)) salts; the encapsulated anion exchange with different anions (SbF6(-), Tf2N(-), NO3(-), TsO(-)) was studied and the results with NO3(-) and TsO(-) indicate that anions on the cage surfaces affect the encapsulated anion exchange and the occupancy of the cage. PMID:27064122

  10. Influence of montmorillonites exchange capacity on the basal spacing of cation–anion organo-montmorillonites

    Energy Technology Data Exchange (ETDEWEB)

    Sanqin, Wu [School of Materials Sciences and Technology, China University of Geosciences, No. 29 Xueyuan Road, Beijing, 100083 (China); Zepeng, Zhang, E-mail: unite508@163.com [School of Materials Sciences and Technology, China University of Geosciences, No. 29 Xueyuan Road, Beijing, 100083 (China); Yunhua, Wang [Zhejiang Fenghong New Material Co., Ltd. (China); Libing, Liao [School of Materials Sciences and Technology, China University of Geosciences, No. 29 Xueyuan Road, Beijing, 100083 (China); Jiansheng, Zhang [Tangshan College, Tangshan 063000 (China)

    2014-11-15

    Graphical abstract: This picture shows the distribution of organic modifier (CTAB and SDS) in Mt interlayer and the basal spacing changes of Mt modified by CTAB and SDS. Organic modifier molecule in Mt interlayer is more and more orderly. The basal spacing of Mt is from 1.5 nm to 5 nm as modifier added. - Highlights: • The d{sub 001} of Ca-Mt, R-Na-Mt, Na-Mt modified by CTAB and SDS can reach 5 nm. • It is easier to get cation–anion OMt with greater d{sub 001} if CEC is lower. • The organic molecules distribution in cation–anion OMt was analyzed. • The influence mechanism of Ca-Mt CEC on the d{sub 001} was discussed. - Abstract: With cationic and anionic surfactants cetyltrimethylammonium bromide (CTAB) and sodium dodecylsulfonate (SDS) as modifiers, Ca-montmorillonites (Ca-Mt), artificial Na-montmorillonites (R-Na-Mt) and natural Na-montmorillonites (Na-Mt) with different cation exchange capacity (CEC) were modified by solution intercalation method, respectively. Then cation–anion organo-montmorillonites (OMt) were prepared. The influence of CEC on the basal spacing of cation–anion OMt and the influence mechanism were discussed by X-ray diffraction (XRD) and zeta potential testing. The results indicate that the basal spacing of cation–anion OMt is related to CEC. For the same type montmorillonites, the basal spacing of cation–anion OMt decreases with the increase of CEC and it is easier to get cation–anion OMt with greater basal spacing when CEC is lower. Moreover, the CEC of Na-Mt has the greatest influence on the basal spacing of cation–anion OMt.

  11. Performance evaluation method for an anion exchange resin and a method of controlling water processing system by using the method

    International Nuclear Information System (INIS)

    The present invention concerns a method of previously forecasting the limit for the use of an anion exchange resin to be used in a condensate desalting device in a nuclear power plant. A polystyrene sulfonic acid (PSS) is previously absorbed to an anion exchange resin and then a reaction rate of the anionic exchange resin is measured. The relation between the adsorbing amount of PSS and the reaction rate is measured, and the extent of degradation of the anionic exchange resin can be evaluated based on the PSS adsorption amount at a portion where the reaction rate is greatly lowered. Namely, the anionic exchange resin is more degraded as the reaction rate is lowered at a lesser adsorption amount, and it is judged that the resin is close to the working limit. With such procedures, the water processing system can be controlled stably. (T.M.)

  12. THE TESTS AND MECHANISM ABOUT SODIUM IONS FROM AN ANION EXCHANGER

    Institute of Scientific and Technical Information of China (English)

    ZhuXingbao; YuJinchun; 等

    1996-01-01

    There exists a universal phenomena that sodium ions are leaked from the strong basic anion exdchanger in operation,which has been puzzling the researchers working in the field of water treatment for years.It is well known that the leakage of sodium ions will seriously affect the pruity of effluent.On the basis of lots of laboratory and industrial experiments,the mechanism of the sodium ions leaked from an anion exchanger has been preliminarily made out and some new chemical reaction equations as well as some improving measures have been put forward in this article.

  13. Design of Anion Exchange Membranes and Electrodialysis Studies for Water Desalination

    Directory of Open Access Journals (Sweden)

    Muhammad Imran Khan

    2016-05-01

    Full Text Available Anion exchange membranes are highly versatile and nowadays have many applications, ranging from water treatment to sensing materials. The preparation of anion exchange membranes (AEMs from brominated poly(2,6-dimethyl-1,6-phenylene oxide (BPPO and methyl(diphenylphosphine (MDPP for electrodialysis was performed. The physiochemical properties and electrochemical performance of fabricated membranes can be measured by changing MDPP contents in the membrane matrix. The influence of a quaternary phosphonium group associated with the removal of NaCl from water is discussed. The prepared membranes have ion exchange capacities (IEC 1.09–1.52 mmol/g, water uptake (WR 17.14%–21.77%, linear expansion ratio (LER 7.96%–11.86%, tensile strength (TS 16.66–23.97 MPa and elongation at break (Eb 485.57%–647.98%. The prepared anion exchange membranes were employed for the electrodialytic removal of 0.1 M NaCl aqueous solution at a constant applied voltage. It is found that the reported membranes could be the promising candidate for NaCl removal via electrodialysis.

  14. Multilayer chitosan-based open tubular capillary anion exchange column with integrated monolithic capillary suppressor

    International Nuclear Information System (INIS)

    Highlights: ► Uses a multilayer chitosan–glutaraldehyde coating as anion exchanger. ► Uses a methacrylate-acrylic acid polymer monolith as suppressor. ► Demonstrates first integral suppressor open tubular anion chromatography. - Abstract: We describe a multilayered open tubular anion exchange column fabricated by alternately pumping solutions of chitosan and glutaraldehyde. The column is terminated in an integrally bonded monolithic suppressor cast around a mandrel of a tungsten wire, composed of an acrylic acid (AA)–ethylene dimethacrylate (EDMA) monolith that is made with sufficient porogen for the monolith to function as a membrane. For a 4.5 m long 75 μm bore column coated with 24 successive layers of the condensation polymer (estimated to contain ∼72 molecular layers) and coupled to 1 cm length of a suppressor fabricated with 55–60% AA, effective separation of several common anions (F−, Cl−, NO2−, Br−, NO3−, average number of theoretical plates ∼12,000) and adequate suppression of 1 mM KOH used as eluent was observed at a flow rate of 800 nL min−1 to obtain sub-picomol detection limits at an operating pressure of ∼1 bar. The separation is not time efficient but the system can be meritorious in unique niche applications where a small form factor is desired and liquid volume and power consumption are more important than separation speed.

  15. Radioactive iodine waste treatment using electrodialysis with an anion exchange paper membrane

    International Nuclear Information System (INIS)

    In order to simply and safely treat radioactive iodine waste, a study of the removal of iodide ion from radioactive waste using electrodialysis with an anion exchange paper membrane, in which trimethylhydroxylpropylammonium groups were homogeneously dispersed with high density. In Na125I and Na36Cl concentration-cell system, electric ion and water conductances, phenomenological coefficients, have been experimentally determined on basis of nonequilibrium thermodynamics. Prepared paper membrane had higher permselectivity of 125I ion than 36Cl ions by approximately 21%. On the other hand, water flux that was accompanied by an ionic transference in prepared paper membrane was greatly larger than that in typical synthesized membrane. It is suggested that a depression of water mobility is important to practice an ideal radioactive iodide waste electrodialysis system with a novel anion exchange paper membrane

  16. Studies on radiolytic degradation of anion exchange resin under acidic condition

    International Nuclear Information System (INIS)

    With a view to understand the onset of degradation phenomenon of anion exchange resin used in PUREX process for the final purification of Pu, investigation were carried out to trace the chemical signature of radiolytic degradation species soluble in nitric acidic solutions. With this aim Dowex 1x 4 anion exchange resin was subjected to radiolytic degradation in presence of water and nitric acid medium of different strengths ranging from 2M to 7M. The aqueous acidic solutions have been analysed for the presence of aqueous soluble organic fragments arising from resin matrix and change in acidity. The extracted products have also been analysed by Gas chromatography. GLC fingerprint suggest of several degradation products especially at 7M nitric acid and dose of 87 Mrad. (author)

  17. Effects of Polar Organic Solvent on Separation of Y(edta)-/Nd(edta)- Complexes on Polyacrylic Anion Exchangers

    Institute of Scientific and Technical Information of China (English)

    Halina Hubicka; Dorota Kolodynska

    2005-01-01

    The use of polar organic solvents for the separations of rare earth elements (Ⅲ) is effective especially for their extensive separations despite the solubility limitations. The study shows that polyacrylate anion exchangers, particularly the weakly basic, gel anion exchanger Amberlite IRA 68, can be applied to the separation of rare earth complexes with EDTA in H2O-methanol and H2O-ethanol systems. In most cases the determined distribution coefficients of Ln3+ complexes with EDTA in mixed media like water-methanol on polyacrylate anion exchangers are larger than those in pure water media.

  18. Influence of glucose and urea on 125I transport across an anion exchange paper membrane

    International Nuclear Information System (INIS)

    In order to study the influence of glucose and urea on the 125I transport across an anion exchange paper membrane, the transmembrane potential, the fluxes, and the concentrations of 125I, glucose and urea within the membrane were measured in the Na125I concentration-cell system containing glucose or urea. Glucose and urea increased the membrane/solution distribution of the iodide ion, but scarcely affected the diffusion process of iodide ion within the membrane

  19. Comparison of anion exchange resins for recovering plutonium from nitric acid waste

    International Nuclear Information System (INIS)

    Microreticular and macroreticular anion exchange resins were compared for their capability of recovering plutonium from nitric acid waste streams. Plutonium breakthrough capacity and elution behavior of the resins were determined as a function of resin properties. Small-bead microreticular resins with a polystyrene matrix containing 4% divinylbenzene cross-linkage showed the best performance. Of the 20- to 50-mesh resins, the macroreticular resin, Amberlite IRA-938, gave the highest plutonium breakthrough capacity and eluted plutonium the fastest

  20. Rapid detection of malto-oligosaccharide-forming bacterial amylases by high performance anion-exchange chromatography

    DEFF Research Database (Denmark)

    Duedahl-Olesen, Lene; Larsen, K. L.; Zimmermann, W.

    2000-01-01

    High performance anion-exchange chromatography with pulsed amperometric detection was applied for the rapid analysis of malto-oligosaccharides formed by extracellular enzyme preparations from 49 starch-degrading bacterial strains isolated from soil and compost samples. Malto-oligosaccharide-formi......-oligosaccharide-forming amylases, indicated by a predominant formation of maltohexaose from starch, were produced by enzyme preparations from four of the isolates growing at pH 7.0 and 10....

  1. Development of imidazolium-type alkaline anion exchange membranes for fuel cell application

    OpenAIRE

    Ran, J; Wu, L.; XU, T; Varcoe, JR; Ong, AL; Poynton, SD

    2012-01-01

    This study reports the development of imidazolium-type alkaline anion exchange membranes (Im-AAEMs) based on the functionalization of bromomethylated poly(2,6-dimethyl-1,4-phenylene oxide) (BPPO) using 1-methylimdazole. Aromatic polymers bearing bromomethyl, instead of chloromethyl, functional groups were employed as base materials to avoid complicated chloromethylation which require toxic reagents. H NMR and FT-IR spectroscopic data indicated the synthesis of a series of membranes with contr...

  2. Studies on resin degradation products encountered during purification of plutonium by anion exchange

    International Nuclear Information System (INIS)

    Among the methods available for the purification of plutonium in Purex process, anion exchange method offers several advantages. However, on repeated use, the resin gets degraded due to thermal, radiolytic and chemical attacks resulting in chemical as well as physical damage. Frequently, plutonium product eluted from such resin contains significant quantities of white precipitates. A few anion exchange resins were leached with 8 M HNO3 at 60-80degC and the resin degradation products (RDP) in the leach-extract were found to give similar precipitates with tetravalent metal ions like Pu(IV), Th(IV) etc. Tetra propyl ammonium hydroxide in 8 M HNO3 (TPAN) also gave a white precipitate with plutonium similar to the one found in the elution streams. The results indicate that delinked quaternary ammonium functional groups might be responsible for the formation of precipitate. The characteristics of precipitates Th-RDP, Th-TPAN and that isolated from elution stream have been investigated. In a separate study a tentative formula for Th-RDP compound is proposed. The influence of RDP on the extraction of plutonium and other components in Purex process was studied and it was found that RDP complexes metal ions thus marginally affecting the kd values. A spectrophotometric method has been standardised to monitor the extent of degradation of anion exchange resins which is based on the ability of RDP to reduce the colour intensity of Th-thoron complex. This technique can be used to study the stability of the anion exchange resins. (author). 8 refs., 8 tabs., 5 figs.,

  3. Anion Exchange Capacity As a Mechanism for Deep Soil Carbon Storage in Variable Charge Soils

    Science.gov (United States)

    Dietzen, C.; James, J. N.; Ciol, M.; Harrison, R. B.

    2014-12-01

    Soil is the most important long-term sink for carbon (C) in terrestrial ecosystems, containing more C than plant biomass and the atmosphere combined. However, soil has historically been under-represented in C cycling literature, especially in regards to information about subsurface (>1.0 m) layers and processes. Previous research has indicated that Andisols with large quantities of noncrystalline, variable-charge minerals, including allophane, imogolite, and ferrihydrite, contain more C both in total and at depth than other soil types in the Pacific Northwest. The electrostatic charge of variable-charge soils depends on pH and is sometimes net positive, particularly in acid conditions, such as those commonly developed under the coniferous forests of the Pacific Northwest. However, even soils with a net negative charge may contain a mixture of negative and positive exchange sites and can hold some nutrient anions through the anion exchange capacity. To increase our understanding of the effects of variable-charge on soil organic matter stabilization, deep sampling is under way at the Fall River Long-Term Soil Productivity Site in western Washington. This site has a deep, well-drained soil with few rocks, which developed from weathered basalt and is classified as an Andisol of the Boistfort Series. Samples have been taken to a depth of 3 m at eight depth intervals. In addition to analyzing total soil C, these soils will be analyzed to determine functional groups present, cation exchange capacity, anion exchange capacity, and non-crystalline mineral content. These data will be analyzed to determine any correlations that may exist between these mineralogical characteristics, total soil C, and types of functional groups stored at depth. The most abundant organic functional groups, including carboxylic and phenolic groups, are anionic in nature, and soil positive charge may play an important role in binding and stabilizing soil organic matter and sequestering C.

  4. Anion exchange selectivity of surfactant modified clinoptilolite-rich tuff for environmental remediation.

    Science.gov (United States)

    de Gennaro, Bruno; Catalanotti, Lilia; Bowman, Robert S; Mercurio, Mariano

    2014-09-15

    Lately, the functionalization of industrial minerals with high technological properties, such as natural zeolites, is shaping as a promising approach in environmental sphere. In fact, under the specific conditions, the surface functionalization via adsorption of cationic surfactants reverses the surface charge of the mineral, enabling zeolites to simultaneously interact either with organic contaminants or inorganic anions. This aspect allows zeolites to be used in the remediation of contaminated fluids. The present research shed new light on some still not fully understood aspects concerning exchange kinetics such as anion-exchange mechanisms and selectivity of surface modified minerals. For this purpose the mineralogical characterization and the surface properties evaluation (X Ray Powder Diffraction, chemical analysis, thermal analysis, ECEC and AEC) of a clinoptilolite-rich tuff were performed, and the anion exchange isotherms of the sample, modified with hexadecyltrimethylammonium chloride or bromide (HDTMA-Cl/-Br), were determined. Ion-exchange equilibrium data of uni-uni valent reaction were obtained by solutions containing Br(-), Cl(-), NO3(-) or ClO4(-). Liquid phase was analysed via high performance liquid chromatography. Thermodynamic quantities (Ka and ΔG(0)) were determined and compared with the Hofmeister series. The value of the ECEC, calculated in batch conditions, was about 137 mmol/kg, in good agreement with that evaluated in dynamic conditions, while the AEC data were different for the SMNZ-Br and -Cl samples, amounting to 137 and 106 mmol/kg, respectively, thus indicating a different compactness of the bilayer formed in the two cases. Moreover, the anion isotherm results and the mathematical evaluation of the thermodynamic parameters, demonstrated the good affinity of SMNZ-Br towards chloride, nitrate and perchlorate, and of SMNZ-Cl for nitrate and perchlorate, also endorsing the possibility of using the same thermodynamic approach developed to

  5. A basic study for the boron thermal regeneration system using anion exchange resins

    International Nuclear Information System (INIS)

    For the boron thermal regeneration system (BTRS), the basic characteristics of commercial anion exchange resin have been investigated on the swelling characteristics, absorption, desorption and temperature coefficient of exchange capacity for boric acid. The equilibrium capacity increases as decrease of temperature and depends strongly on the degrees of cross linking having a maximum point at about 7% of DVB. The temperature coefficient of equilibrium capacity of boric acid is also a function of the concentration of external solution and of the cross linking having a maximum point around 7% of DVB. (author)

  6. Retention behavior of C1-C6 aliphatic monoamines on anion-exchange and polymethacrylate resins with heptylamine as eluent.

    Science.gov (United States)

    Ohta, Kazutoku; Ohashi, Masayoshi; Jin, Ji-Ye; Takeuchi, Toyohide; Fujimoto, Chuzo; Choi, Seong-Ho; Ryoo, Jae Jeong; Lee, Kwang-Pill

    2004-06-11

    Retention behavior of C1-C6, aliphatic monoamines (methylamine, ethylamine, propylamine, butylamine, amylamine and hexylamine) on columns (150 mm x 6 mm i.d.) packed with various anion-exchange resins (styrene-divinylbenzene (PS-DVB) copolymer-based strongly basic anion-exchange resin: TSKgel SAX, polymethacrylate-based strongly basic anion-exchange resin: TSKgel SuperQ-5PW and polymethacrylate-based weakly basic anion-exchange resin: TSKgel DEAE-5PW) and unfunctionized polymethacrylate resins (TSKgel G5000PW and TSKgel G3000PWXL) was investigated with basic solutions (sodium hydroxide and heptylamine) as the eluents. Due to strongly electrostatic repulsion (ion-exclusion effect) between these anion-exchange resins and these amines, peak resolution between these amines on these anion-exchange resin columns was unsatisfactory with both sodium hydroxide and heptylamine as the eluents. In contrast, these polymethacrylate resins were successfully applied as the stationary phases for the separation of these C1-C6 amines with heptylamine as eluent, because of both small hydrophobicity and small cation-exchange ability of these resins. Excellent simultaneous separation, highly sensitive conductimetric detection and symmetrical peaks for these C1-C6 amines were achieved on the TSKgel G3000PWXL column in 35 min with 5 mM heptylamine at pH 11.1 as the eluent. PMID:15250421

  7. New Anion-Exchange Resins for Improved Separations of Nuclear Materials

    International Nuclear Information System (INIS)

    Improved separations of nuclear materials will have a significant impact upon a broad range of DOE activities. DOE-EM Focus Areas and Crosscutting Programs have identified improved methods for the extraction and recovery of radioactive metal ions from process, waste, and environmental waters as critical needs for the coming years. We propose to develop multifunctional anion-exchange resins that facilitate anion uptake by carefully controlling the structure of the anion receptor site. Our new ion-exchange resins interface the field of ion-specific chelating ligands with robust, commercial ion-exchange technology to provide materials which exhibit superior selectivity and kinetics of sorption and desorption. The following Focus Areas and Crosscutting Programs have described needs that would be favorably impacted by the new material: Efficient Separations and Processing - radionuclide removal from aqueous phases; Plutonium - Pu, Am or total alpha removal to meet regulatory requirement s before discharge to the environment; Plumes - U and Tc in groundwater, U, Pu, Am, and Tc in soils; Mixed Waste - radionuclide partitioning; High-Level Tank Waste - actinide and Tc removal from supernatants and/or sludges. The basic scientific issues which need to be addressed are actinide complex speciation along with modeling of metal complex/functional site interactions in order to determine optimal binding-site characteristics. Synthesis of multifunctionalized extractants and ion-exchange materials that implement key features of the optimized binding site, and testing of these materials, will provide feedback to the modeling and design activities. Resin materials which actively facilitate the uptake of actinide complexes from solution should display both improved selectivity and kinetic properties. The long-range implications of this research, however, go far beyond the nuclear complex. This new methodology of ''facilitated uptake'' could revolutionize ion-exchange technology

  8. DEVELOPMENT AND CHARACTERIZATION OF POLYVINYLIDENE FLUORIDE - IMIDAZOLIUM FUNCTIONALIZED POLYSULFONE BLEND ANION EXCHANGE MEMBRANE

    Directory of Open Access Journals (Sweden)

    S. VELU

    2015-09-01

    Full Text Available Anion exchange membrane (AEM is one of the core components of an alkaline fuel cell influencing the fuel cell’s performance, durability and stability. Out of the many anion exchange membranes reported so far, imidazolium functionalized polysulfone (PSf-ImOH membrane has been identified to have high hydroxide ionic conductivity, reaching up to 50 mS cm-1 at 20oC. However, at high levels of ion exchange capacity, the membrane’s water uptake and swelling ratio increases significantly with temperature thus destabilizing it and making it unfit for potential use in high temperature alkaline fuel cells. This limitation of PSf-ImOH membranes has been overcome by blending it with polyvinylidene fluoride (PVDF polymer, which is a thermally stable and highly hydrophobic polymer. PSf-ImOH membrane with a high degree of chloromethylation (180% was synthesized and blended with PVDF at different weight ratios (PVDF / PSf-ImOH: 30/70, 50/50 and 70/30 to create a series of novel anion exchange membranes. The prepared membranes were characterized to study their structure, water uptake, swelling ratio, solubility in low boiling water soluble solvents, thermal stability, ion exchange capacity (IEC and ionic conductivity (IC at different temperatures. The 70% PVDF blend membrane demonstrated the better performance in terms of IEC, IC and water uptake properties compared to other membranes. Comparative studies on the water uptake and IC variation between the 70% PVDF blend membrane and pure PSfImOH membrane (having the same IEC as that of the blend membrane, clearly indicated the superiority and the promising use of the blend membrane in alkaline fuel cell especially for high temperature working condition.

  9. Ammonium Bicarbonate Transport in Anion Exchange Membranes for Salinity Gradient Energy

    KAUST Repository

    Geise, Geoffrey M.

    2013-09-17

    Many salinity gradient energy technologies such as reverse electrodialysis (RED) rely on highly selective anion transport through polymeric anion exchange membranes. While there is considerable interest in using thermolytic solutions such as ammonium bicarbonate (AmB) in RED processes for closed-loop conversion of heat energy to electricity, little is known about membrane performance in this electrolyte. The resistances of two commercially available cation exchange membranes in AmB were lower than their resistances in NaCl. However, the resistances of commercially available anion exchange membranes (AEMs) were much larger in AmB than in NaCl, which would adversely affect energy recovery. The properties of a series of quaternary ammonium-functionalized poly(phenylene oxide) and Radel-based AEMs were therefore examined to understand the reasons for increased resistance in AmB to overcome this performance penalty due to the lower mobility of bicarbonate, 4.59 × 10-4 cm2/(V s), compared to chloride, 7.90 × 10-4 cm2/(V s) (the dilute aqueous solution mobility ratio of HCO3 - to Cl- is 0.58). Most membrane resistances were generally consistent with the dilute solution mobilities of the anions. For a few key samples, however, increased water uptake in AmB solution reduced the ionic resistance of the polymer compared to its resistance in NaCl solution. This increased water uptake was attributed to the greater hydration of the bicarbonate ion compared to the chloride ion. The increased resistance due to the use of bicarbonate as opposed to chloride ions in AEMs can therefore be mitigated by designing polymers that swell more in AmB compared to NaCl solutions, enabling more efficient energy recovery using AmB thermolytic solutions in RED. © 2013 American Chemical Society.

  10. Mono- and polyprotic buffer systems in anion exchange chromatography of influenza virus particles.

    Science.gov (United States)

    Vajda, Judith; Weber, Dennis; Stefaniak, Sabine; Hundt, Boris; Rathfelder, Tanja; Müller, Egbert

    2016-05-27

    Different ions typically used in downstream processing of biologicals are evaluated for their potential in anion exchange chromatography of an industrially produced, pandemic influenza H1N1 virus. Capacity, selectivity and recovery are investigated based on single step elution parallel chromatography experiments. The inactivated H1N1 feedstream is produced in Madin-Darby Bovine Kidney cells. Interesting effects are found for sodium phosphate and sodium citrate. Both anions are triprotic kosmotropes. Anion exchange chromatography generally offers high scalability to satisfy sudden demands for vaccines, which may occur in case of an emerging influenza outbreak. Appropriate pH conditions for H1N1 adsorption are determined by Zeta potential measurements. The dynamic binding capacity of a salt tolerant polyamine-type resin is up to 6.4 times greater than the capacity of a grafted Q-type resin. Pseudo-affinity interactions of polyamines with the M2 protein of influenza may contribute to the obtained capacity increase. Both resins achieve greater capacity in sodium phosphate buffer compared to Tris/HCl. A recovery of 67% and DNA clearance close to 100% without DNAse treatment are achieved for the Q-type resin. Recovery of the virus from the salt tolerant resin requires the use of polyprotic acids in the elution buffer. 85% of the DNA and 60% of the proteins can be removed by the salt tolerant resin. The presence of sodium phosphate during anion exchange chromatography seems to support stability of the H1N1 particles in presence of hydrophobic cations. PMID:27130581

  11. Models for the estimation of thermodynamic properties of layered double hydroxides: application to the study of their anion exchange characteristics

    OpenAIRE

    Bravo-Suárez Juan J.; Páez-Mozo Edgar A.; Oyama S. Ted

    2004-01-01

    Several models for the estimation of thermodynamic properties of layered double hydroxides (LDHs) are presented. The predicted thermodynamic quantities calculated by the proposed models agree with experimental thermodynamic data. A thermodynamic study of the anion exchange process on LDHs is also made using the described models. Tables for the prediction of monovalent anion exchange selectivities on LDHs are provided. Reasonable agreement is found between the predicted and the experimental mo...

  12. Hydration and sorption characteristics of a polyfunctional weak-base anion exchanger after the sorption of vanillin and ethylvanillin

    Science.gov (United States)

    Rodionova, D. O.; Voronyuk, I. V.; Eliseeva, T. V.

    2016-07-01

    Features of the sorption of substituted aromatic aldehydes by a weak-base anion exchanger under equilibrium conditions are investigated using vanillin and ethylvanillin as examples. Analysis of the sorption isotherms of carbonyl compounds at different temperatures allows us to calculate the equilibrium characteristics of their sorption and assess the entropy and enthalpy contributions to the energy of the process. Hydration characteristics of the macroporous weak-base anion exchanger before and after the sorption of aromatic aldehydes are compared.

  13. Modelling and optimization of the ion exchange membrane bioreactor for removal of anionic pollutants from drinking water streams

    OpenAIRE

    Ricardo, Ana Rita da Fonseca

    2011-01-01

    The present work aimed at studying the treatment of drinking water supplies contaminated with perchlorate and nitrate, using the Ion Exchange Membrane Bioreactor (IEMB) concept. This system combines the transport of these two anions from contaminated water, through an anion exchange membrane, with their biological reduction in a separate compartment. In the IEMB, the mass transport is dependent not only from membrane properties but also from the biocompartment conditions. Multivariate stat...

  14. Sorption of uranium(VI) ions from hydrochloric acid and ammonium chloride solutions by anion exchangers

    International Nuclear Information System (INIS)

    The sorption of macroscopic quantities of uranium from solutions of UO2Cl2 containing HCl and NH4Cl in concentrations from 0.0 to 6.0 M by the AV-17 x 8, AV-16G, EDE-10P, AN-31, AN-2F, AN22, and AN-251 anion exchangers has been investigated under static conditions. The sorption isotherms are described by an equation similar to Freundlich's equation: K/sub d/ = K tilde x C/sub eq/sup 1/z/ or log K/sub d/ = log K tilde + 1/z x log C/sub eq/. Equations describing the dependence of the sorbability (or K/sub d/) on the equilibrium concentration of uranium in the solution have been obtained with the aid of the least-squares method. Conclusions regarding the chemistry of the exchange of uranium ions on anion exchangers in chloride solutions have been drawn on the basis of the UV spectra of the original solutions and the IR spectra of the ion exchangers obtained in this work, as well as the established general laws governing sorption

  15. Sorption of uranium(VI) ions from hydrochloric acid and ammonium chloride solutions by anion exchangers

    Energy Technology Data Exchange (ETDEWEB)

    Pakholkov, V.S.; Denisova, L.A.; Rychkov, V.N.; Kurnosenko, N.A.

    1988-01-01

    The sorption of macroscopic quantities of uranium from solutions of UO/sub 2/Cl/sub 2/ containing HCl and NH/sub 4/Cl in concentrations from 0.0 to 6.0 M by the AV-17 x 8, AV-16G, EDE-10P, AN-31, AN-2F, AN22, and AN-251 anion exchangers has been investigated under static conditions. The sorption isotherms are described by an equation similar to Freundlich's equation: K/sub d/ = K tilde x C/sub eq/sup 1/z/ or log K/sub d/ = log K tilde + 1/z x log C/sub eq/. Equations describing the dependence of the sorbability (or K/sub d/) on the equilibrium concentration of uranium in the solution have been obtained with the aid of the least-squares method. Conclusions regarding the chemistry of the exchange of uranium ions on anion exchangers in chloride solutions have been drawn on the basis of the UV spectra of the original solutions and the IR spectra of the ion exchangers obtained in this work, as well as the established general laws governing sorption.

  16. Synthesis and Characterization of Imidazolium Linear Bisphenol Polycarbonate Hydroxides for Anion Exchange Membrane.

    Science.gov (United States)

    Jang, Hohyoun; Hossain, Md Awlad; Lee, Soonho; Ha, Jaesung; Yoo, Jihoo; Kim, Kyungchul; Kim, Whangi

    2015-11-01

    A novel anion exchange membrane of imidazolium functionalized bisphenol polycarbonate was prepared for application in alkaline fuel cell. Di-imidazolium polycarbonate anionic membrane was synthesized by sequential interfacial polymerization, chloromethylation, substitution with 1-methylimidazole and ion exchange with 1.0 M KOH. Chloromethylation reaction was quantitative to achieve a high content of hydroxide ions. Introduction of conjugated imidazole ring in polymer plays an important role to improve both thermal and chemical stability. Bisphenol polycarbonate is a flexible polymer and shows a good solubility in polar organic solvent. The alkaline imidazolium bisphenol polycarbonate rendered an elevated molecular weight with excellent solubility in polar aprotic solvent. Different levels of substitution and ion exchange were investigated; the resulting membranes showed high ion exchange capacities (IECs) of up to 2.15 mmol g(-1). The imidazolium-functionalized copolymer membranes showed lower water affinity (14.2-42.8% at 30 degrees C) that satisfied an essential criterion for fuel cell application. The chemical structure of the imidazolium functionalized polycarbonate membrane was confirmed by 1H NMR spectroscopy, and also the membrane properties were evaluated by thermogravimetric analysis (TGA) and water uptake (WU), IEC and conductivity assessment. They exhibited hydroxide conductivity above 10(-2) S cm(-1) at room temperature and good chemical stability for up to five days without significant losses of ion conductivity. PMID:26726604

  17. Studies on the absorption of boric acid on anion exchange resin, (1)

    International Nuclear Information System (INIS)

    Boron Thermal Regeneration (BTR) with an anion exchange resin is a system for the control of boric acid concentration in the primary coolant of a pressurized water reactor. The absorption characteristics of boric acid on strong base anion exchange resin was investigated at 250C. Boric acid absorption was estimated by analysis of solution eluted with sodium chloride solution, from the ion exchange resin column. The average value adsorbed experimentally per ion exchange group was in the range of 1.4 to 4.2 for boric acid solutions in concentrations of 0.00925 to 0.647 mol dm-3. The pH within the borate form resin was pH 8 to 14 for boric acid solutions in concentrations of 0.00925 to 0.462 mol dm-3. The presence of orthoborate ion, tetraborate (mono and divalent) ion and pentaborate (mono and divalent) ion was anticipated in the resin phase. Acid dissociation constants (pK) of these five ion species were estimated to be 8.95 for orthoborate, 5.6 for monovalent tetraborate, 15.2 for divalent tetraborate, 5.6 for monovalent pentaborate and 13.8 for divalent pentaborate. (author)

  18. Removal of fluorescent dissolved organic matter in biologically treated textile effluents by NDMP anion exchange process: efficiency and mechanism.

    Science.gov (United States)

    Li, Wen-Tao; Xu, Zi-Xiao; Shuang, Chen-Dong; Zhou, Qing; Li, Hai-Bo; Li, Ai-Min

    2016-03-01

    The efficiency and mechanism of anion exchange resin Nanda Magnetic Polymer (NDMP) for removal of fluorescent dissolved organic matter in biologically treated textile effluents were studied. The bench-scale experiments showed that as well as activated carbon, anion exchange resin could efficiently remove both aniline-like and humic-like fluorescent components, which can be up to 40 % of dissolved organic matter. The humic-like fluorescent component HS-Em460-Ex3 was more hydrophilic than HS-Em430-Ex2 and contained fewer alkyl chains but more acid groups. As a result, HS-Em460-Ex3 was eliminated more preferentially by NDMP anion exchange. However, compared with adsorption resins, the polarity of fluorescent components had a relatively small effect on the performance of anion exchange resin. The long-term pilot-scale experiments showed that the NDMP anion exchange process could remove approximately 30 % of the chemical oxygen demand and about 90 % of color from the biologically treated textile effluents. Once the issue of waste brine from resin desorption is solved, the NDMP anion exchange process could be a promising alternative for the advanced treatment of textile effluents. PMID:26578375

  19. Molecular physiology and genetics of Na+-independent SLC4 anion exchangers

    Science.gov (United States)

    Alper, Seth L.

    2009-01-01

    Summary Plasmalemmal Cl–/HCO3– exchangers are encoded by the SLC4 and SLC26 gene superfamilies, and function to regulate intracellular pH, [Cl–] and cell volume. The Cl–/HCO3– exchangers of polarized epithelial cells also contribute to transepithelial secretion and reabsorption of acid–base equivalents and Cl–. This review focuses on Na+-independent electroneutral Cl–/HCO3– exchangers of the SLC4 family. Human SLC4A1/AE1 mutations cause the familial erythroid disorders of spherocytic anemia, stomatocytic anemia and ovalocytosis. A largely discrete set of AE1 mutations causes familial distal renal tubular acidosis. The Slc4a2/Ae2–/– mouse dies before weaning with achlorhydria and osteopetrosis. A hypomorphic Ae2–/– mouse survives to exhibit male infertility with defective spermatogenesis and a syndrome resembling primary biliary cirrhosis. A human SLC4A3/AE3 polymorphism is associated with seizure disorder, and the Ae3–/– mouse has increased seizure susceptibility. The transport mechanism of mammalian SLC4/AE polypeptides is that of electroneutral Cl–/anion exchange, but trout erythroid Ae1 also mediates Cl– conductance. Erythroid Ae1 may mediate the DIDS-sensitive Cl– conductance of mammalian erythrocytes, and, with a single missense mutation, can mediate electrogenic SO42–/Cl– exchange. AE1 trafficking in polarized cells is regulated by phosphorylation and by interaction with other proteins. AE2 exhibits isoform-specific patterns of acute inhibition by acidic intracellular pH and independently by acidic extracellular pH. In contrast, AE2 is activated by hypertonicity and, in a pH-independent manner, by ammonium and by hypertonicity. A growing body of structure–function and interaction data, together with emerging information about physiological function and structure, is advancing our understanding of SLC4 anion exchangers. PMID:19448077

  20. Selective removal of nitrate by using a novel macroporous acrylic anion exchange resin

    Institute of Scientific and Technical Information of China (English)

    Hai Ou Song; Yang Zhou; Ai Min Li; Sandra Mueller

    2012-01-01

    An anion exchange resin NDP-5 has been prepared successfully and applied on the selective removal of nit-ate from SO42-/NO3- binary co-existence system.The composition and morphology of NDP-5 were confirmed by FT-IR and SEM.The NDP-5 resin exhibits the completely different behavior on the adsorption capacity,adsorption kinetic and the effect of the completing anion in the absence or presence of sulfate,compared to D213.And,the resultants of kinetic are well fitted by the pseudo-first-order and pseudo-second-order models.These results are very important to develop novel resins with great features.

  1. Incorporation of multi-walled carbon nanotubes in microspheres used as anion exchange resin via suspension polymerization

    Science.gov (United States)

    Fathy, Mahmoud; Abdel Moghny, Th.; Awadallah, Ahmed E.; El-Bellihi, Abdel-Hameed A.-A.

    2014-06-01

    Amination of vinylbenzyl chloride-divinylbenzene (VBC-DVB) copolymers is an effective method for preparation of anion-exchange resins. Conventionally, the starting polymer is produced by chloromethylation of a styrene-divinylbenzene copolymer that utilizes chloromethyl methyl ether, a known carcinogen. An alterative approach is to copolymerize vinylbenzyl chloride with divinylbenzene to generate the necessary VBC-DVB. This method provides precise control over the density of the ion-exchange groups. The regiochemistry of the vinylbenzyl chloride methods was realized using solvent-ion exchange groups. These resulting anion-exchange polymers were characterized by a variety of techniques such as analytical titrations, transform infrared spectroscopy and thermal gravimetric analysis. Testing of these copolymers for breakthrough was performed. The results indicate that these anion exchangers have a meaningful increase in thermal stability over commercial anionic exchange beads. Resins containing MWCNTs achieved anion exchange capacity value of 323.6 meq/100 g over than that of copolymer resins and that useful in water desalination or treatment.

  2. Performance of selected anion exchange resins for the treatment of a high DOC content surface water.

    Science.gov (United States)

    Humbert, Hugues; Gallard, Hervé; Suty, Hervé; Croué, Jean-Philippe

    2005-05-01

    The objective of this study was first to compare the performance of four strong anion exchange resins (AERs) (MIEX from Orica Pty Ltd, DOWEX-11 and DOWEX-MSA from DOW chemical and IRA-938 from Rohm and Haas) for their application in drinking water treatment (natural organic matter (NOM), mineral anions (nitrate, sulfate and bromide) and pesticide removal) using bench-scale experimental procedures on a high DOC content surface water. The efficiency of MIEX for NOM and mineral anions removal was furthermore evaluated using bench-scale dose-response experiments on raw, clarified and post-ozonated waters. NOM removal was assessed using the measurement of dissolved organic carbon (DOC), UV absorbance at 254 nm (UV254) and the use of high-performance size exclusion chromatography with UV (HPSEC/UV) and fluorescence detection (HPSEC/FLUO). The MIEX and IRA938 anionic resins exhibit a faster removal of NOM and mineral anions compared to the DOWEX11 and MSA AERs. All the resins were found to be very effective with similar performances after 30 to 45 min of contact time. As expected, only limited sorption of atrazine and isoproturon (C0=1 microg/L) occurred with MIEX, DOWEX11 and MSA AERs. MIEX resin proved to be very efficient in eliminating NOM of high-molecular weight but also a large part of the smallest UV absorbing organic compounds which were refractory to coagulation/flocculation treatment. Remaining DOC levels after 30 min of contact with MIEX were found similar in raw water, clarified water and even post-ozonated water implying no DOC benefit can be gained by employing conventional treatment prior to MIEX treatment. Removal of bromide (initial concentration 110 microg/L) was also observed and ranged from 30% to 65% for resin dose increasing from 2 to 8 mL/L. T PMID:15899268

  3. Guanidinium based blend anion exchange membranes for direct methanol alkaline fuel cells (DMAFCs)

    Science.gov (United States)

    Sajjad, Syed D.; Liu, Dong; Wei, Zi; Sakri, Shambhavi; Shen, Yi; Hong, Yi; Liu, Fuqiang

    2015-12-01

    Guanidinium based blend anion exchange membranes (AEMs) for direct methanol alkaline fuel cells have been fabricated and studied. The guanidinium prepolymer is first synthesized through a simple polycondensation process with the ion exchange moieties incorporated directly into the polymer backbone, and then is used to make guanidinium - chitosan (Gu-Chi) blend membranes. Besides, a lipophilic guanidinium prepolymer, synthesized by means of a precipitation reaction between sodium stearate and guanidinium salt, is adopted to tune solubility and mechanical properties of the blend AEMs. Results show that both ionic conductivity and methanol permeability of the AEMs can be tuned by blend composition and chemistry of the guanidinium based prepolymer. The selectivity (ratio of ionic conductivity to methanol permeability) of the fabricated membranes is superior to that of commercial membranes. Under fuel cell tests using 3 M methanol, the open circuit voltage (OCV) value for the blend AEM with 72 wt% of the guanidinium polymer (0.69 V) is much higher than that of the commercial Tokuyama A201 (0.47 V) at room temperature, while the blend AEMs with 50 wt% guanidinium content still show comparable values. Overall, the developed membranes demonstrate superior performance and therefore pose great promise for direct methanol anion exchange fuel cell (DMAFC) applications.

  4. Studies on the adsorption of boric acid on anion exchange resins, 8

    International Nuclear Information System (INIS)

    Borate-form anion exchange resin (type I) is repeatedly used between the process of boric acid adsorption at a low temperature (5 0C) and its desorption at a high temperature (80 0C), to control the boric acid concentration of the primary coolant in PWRs. The thermal stability of the borate form anion exchange resin is an important index for evaluating operational reliability of the processes in the long term. To determine the thermal stability of the resins, heat cycle tests were carried out using borate, OH-, and Cl- form resins. Average mole values (average n) of boric acid adsorbed per functional group of the ion exchange resin were not changed by heat cycling. Residual ratios of salt spiliting capacity of the borate form resins decreased in the range of 92 to 97 % for 0.00924 to 0.185 M boric acid solution after 1700 heat cycles. The ratios for OH- or Cl- form resins which were tested as a reference, were 70 and 95 % respectively. The thermal stability of the resin decreased with an increase in the pH value in the resin phase. (author)

  5. The Drosophila Anion Exchanger (DAE lacks a detectable interaction with the spectrin cytoskeleton

    Directory of Open Access Journals (Sweden)

    Base Christine

    2010-06-01

    Full Text Available Abstract Background Current models suggest that the spectrin cytoskeleton stabilizes interacting ion transport proteins at the plasma membrane. The human erythrocyte anion exchanger (AE1 was the first membrane transport protein found to be associated with the spectrin cytoskeleton. Here we evaluated a conserved anion exchanger from Drosophila (DAE as a marker for studies of the downstream effects of spectrin cytoskeleton mutations. Results Sequence comparisons established that DAE belongs to the SLC4A1-3 subfamily of anion exchangers that includes human AE1. Striking sequence conservation was observed in the C-terminal membrane transport domain and parts of the N-terminal cytoplasmic domain, but not in the proposed ankyrin-binding site. Using an antibody raised against DAE and a recombinant transgene expressed in Drosophila S2 cells DAE was shown to be a 136 kd plasma membrane protein. A major site of expression was found in the stomach acid-secreting region of the larval midgut. DAE codistributed with an infolded subcompartment of the basal plasma membrane of interstitial cells. However, spectrin did not codistribute with DAE at this site or in anterior midgut cells that abundantly expressed both spectrin and DAE. Ubiquitous knockdown of DAE with dsRNA eliminated antibody staining and was lethal, indicating that DAE is an essential gene product in Drosophila. Conclusions Based on the lack of colocalization and the lack of sequence conservation at the ankyrin-binding site, it appears that the well-characterized interaction between AE1 and the spectrin cytoskeleton in erythrocytes is not conserved in Drosophila. The results establish a pattern in which most of the known interactions between the spectrin cytoskeleton and the plasma membrane in mammals do not appear to be conserved in Drosophila.

  6. Copper modified platinum electrode for amperometric detection of spectinomycin sulfate by anion-exchange chromatography

    Institute of Scientific and Technical Information of China (English)

    Ling Ling Xi; Pei Min Zhang; Yan Zhu

    2009-01-01

    A La~(3+)-Cu/Pt modified electrode was fabricated by electrodepositing process in CuSO_4 solution by adding a small amount of lanthium compound, and it was employed for direct current (DC) amperometric detection of spectinomycin by anion-exchange chromatography. Without derivatization, this method can simultaneously determine the main component and impurities in spectinomycin pharmaceutical raw material. Ease of preparation, being applied in DC detection mode and good catalytic stability confirmed the interests of this modified electrode as amperometric sensor for the determination of spectinomycin.

  7. Determination of petroleum sulfonates in crude oil by column-switching anion-exchange chromatography

    Institute of Scientific and Technical Information of China (English)

    Liang Zhao; Xu Long Cao; Hong Yan Wang; Xia Liu; Sheng Xiang Jiang

    2008-01-01

    A column-switching anion-exchange chromatography method was described for the separation and determination of petroleum monosulfonates (PMS)and petroleum disulfonates (PDS)in crude oil that was simply diluted with the dichloromethane/methanol (60140).The high performance liquid chromatography (HPLC)system consisted of a clean-up column and an analytical column,which were connected with two six-port switching valves.Detection of petroleum sulfonates was available and repeatable.This method has been successfully applied to determine PMS and PDS in crude oil samples from Shengli oil field.

  8. Synthesis and characterization of quaternized poly(phthalazinone ether sulfone ketone) for anion-exchange membrane

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Chloromethylated poly(phthalazinone ether sulfone ketone) (CMPPESK) was prepared from poly(phthalazinone ether sulfone ketone) (PPESK) using chloromethyl octyl ethers (CMOE) with lower toxicity as chloromethylated regent. CMPPESK was soluble in N-methyl-2-pyrrolidone (NMP), N,N-dimethylacetamide (DMAc) and chloroform. Quatemized poly(phthalazinone ether sulfone ketone) (QAPPESK) was prepared from CMPPESK by quaternization. QAPPESK had excellent solvent resistance,which was only partly soluble in sulfuric acid (98%) and swollen in N,N-dimethylformamide (DMF). The vanadium redox flow battery (V-RFB) using QAPPESK anion-exchange membrane had better performance with 88.3% of overall energy efficiency.

  9. Synergistic desorption of molybdenum from the strong base anion exchange resin by molybdnum fouling

    International Nuclear Information System (INIS)

    In this paper the synerglstic desorption of molybdenum from the strong base anion exchange resin is studied using ammonium hydroxide and ammonium sulfate, sodium hydroxide and sodium sulfate or sodium hydroxide and sodium chloride mixed chloride mixed desorbents. The coefficients of synergistlc desorption for various mixed desorbents are obtained. The experimental results show that the desorption efficiency of the mixed desorbent containing ammonium hydroxide and ammonium sulfate is so high that it can substitute for the mixed desorbent used in the plant. The harmful affect of the chloride ion on production can be eliminated if this mixed desorbent is used for the plant

  10. Ectopic expression of the erythrocyte band 3 anion exchange protein, using a new avian retrovirus vector

    DEFF Research Database (Denmark)

    Fuerstenberg, S; Beug, H; Introna, M;

    1990-01-01

    A retrovirus vector was constructed from the genome of avian erythroblastosis virus ES4. The v-erbA sequences of avian erythroblastosis virus were replaced by those coding for neomycin phosphotransferase, creating a gag-neo fusion protein which provides G418 resistance as a selectable marker. The...... exchange protein has been expressed from the vector in both chicken embryo fibroblasts and QT6 cells and appears to function as an active, plasma membrane-based anion transporter. The ectopic expression of band 3 protein provides a visual marker for vector function in these cells....

  11. Anion exchange equilibrium of uranium and several other elements in mineral acid solutions containing tetrafluoroboric acid

    International Nuclear Information System (INIS)

    Volume distribution coefficients (Dv) were determined for the adsorption of U and several other elements on anion-exchange resin from mixed solutions of tetrafluoroboric acid and nitric acid or hydrochloric acid, and the effect of tetrafluoroboric acid on the adsorption of each element was studied. The addition of tetrafluoroboric acid, in general, slightly decreased the Dv values while Zr weakly adsorbed in the HBF4-HCl and HBF4-HNO3 solutions and Nb in the NBF4-HNO3 solutions. (author) 18 refs.; 4 figs

  12. Determination of uranium isotopes in environmental samples by anion exchange in sulfuric and hydrochloric acid media.

    Science.gov (United States)

    Popov, L

    2016-09-01

    Method for determination of uranium isotopes in various environmental samples is presented. The major advantages of the method are the low cost of the analysis, high radiochemical yields and good decontamination factors from the matrix elements, natural and man-made radionuclides. The separation and purification of uranium is attained by adsorption with strong base anion exchange resin in sulfuric and hydrochloric acid media. Uranium is electrodeposited on a stainless steel disk and measured by alpha spectrometry. The analytical method has been applied for the determination of concentrations of uranium isotopes in mineral, spring and tap waters from Bulgaria. The analytical quality was checked by analyzing reference materials. PMID:27451111

  13. ELECTROCHEMICAL STABILITY OF STRONG BASIC ANION EXCHANGE MEMBRANES IN CONDITIONS OF HIGH INTENSIVE ELECTRODIALYSIS PROCESS

    Directory of Open Access Journals (Sweden)

    Zabolotskiy V. I.

    2014-12-01

    Full Text Available The stability of strongly basic anion-exchange membranes MA-41-2P (JSC "Schekino-Nitrogen", Russia and AMX (Tokuyama Soda, Japan under intensive current regimes was investigated in the current study. The process of water molecules dissociation at current densities above the limiting one in 0.01 M sodium chloride solution was studied in detail. The length of the electroconvective instability at the membrane / solution interface at currents exceeding the limiting current was measured by laser interferometry

  14. Anion Effects on the Ion Exchange Process and the Deformation Property of Ionic Polymer Metal Composite Actuators

    Directory of Open Access Journals (Sweden)

    Wataru Aoyagi

    2016-06-01

    Full Text Available An ionic polymer-metal composite (IPMC actuator composed of a thin perfluorinated ionomer membrane with electrodes plated on both surfaces undergoes a large bending motion when a low electric field is applied across its thickness. Such actuators are soft, lightweight, and able to operate in solutions and thus show promise with regard to a wide range of applications, including MEMS sensors, artificial muscles, biomimetic systems, and medical devices. However, the variations induced by changing the type of anion on the device deformation properties are not well understood; therefore, the present study investigated the effects of different anions on the ion exchange process and the deformation behavior of IPMC actuators with palladium electrodes. Ion exchange was carried out in solutions incorporating various anions and the actuator tip displacement in deionized water was subsequently measured while applying a step voltage. In the step voltage response measurements, larger anions such as nitrate or sulfate led to a more pronounced tip displacement compared to that obtained with smaller anions such as hydroxide or chloride. In AC impedance measurements, larger anions generated greater ion conductivity and a larger double-layer capacitance at the cathode. Based on these mechanical and electrochemical measurements, it is concluded that the presence of larger anions in the ion exchange solution induces a greater degree of double-layer capacitance at the cathode and results in enhanced tip deformation of the IPMC actuators.

  15. Adsorption of Monobutyl Phthalate from Aqueous Phase onto Two Macroporous Anion-Exchange Resins

    Directory of Open Access Journals (Sweden)

    Zhengwen Xu

    2014-01-01

    Full Text Available As new emerging pollutants, phthalic acid monoesters (PAMs pose potential ecological and human health risks. In the present study, adsorption performance of monobutyl phthalate (MBP onto two macroporous base anion-exchange resins (D-201 and D-301 was discussed. It was found that the adsorption isotherms were best fitted by the Langmuir equation while the adsorption kinetics were well described by pseudo-first-order model. Analyses of sorption isotherms and thermodynamics proved that the adsorption mechanisms for DBP onto D-201 were ion exchange. However, the obtained enthalpy values indicate that the sorption process of MBP onto D-301 is physical adsorption. The equilibrium adsorption capacities and adsorption rates of DBP on two different resins increased with the increasing temperature of the solution. D-301 exhibited a higher adsorption capacity of MBP than D-201. These results proved that D-301, as an effective sorbent, can be used to remove phthalic acid monoesters from aqueous solution.

  16. Comparison among three anion exchange chromatographic supports to capture erythropoietin from cell culture supernatant

    Institute of Scientific and Technical Information of China (English)

    Lourdes HERNNDEZ; Diobel STEWART; Lourdes ZUMALACRREGUI; Daniel AMARO

    2015-01-01

    Affinity and ion exchange conventional chromatography have been used to capture erythropoietin ( EPO)from mammalian cell culture supernatant. Currently,chromatographic adsorbent perfusion is available, however a limited number of applications have been found in the literature. In this work,three anion exchange chromatographic supports( gel,membrane and monolithic)were evaluated in the capture step of the recombi-nant erythropoietin purification process. The influences of load and flow rate on each support performance were analyzed. Also the purity of the EPO molecules was determined. A productivity analysis,as a decision tool for larger scale implementation,was done. As a conclusion,the evaluated supports are technically suitable to cap-ture EPO with adequate recovery and good purity. However,the monolithic column admits high operating velocity,showing the highest adsorption capacity and productivity.

  17. Radiolysis of the AV-17×8 ČS anion-exchange resin

    Science.gov (United States)

    Bartoníček, B.; Habersbergerová, A.; Janovský, I.; Kysela, J.; Pejša, R.

    The mixture of the anion exchange resin AV-17×8 čs in borate form and of a deaerated aqueous solution containing H 3BO 3 and NH 3 ( pH = 7) was irradiated with gamma rays in both static and dynamic conditions. A loss of strong-base exchange capacity and an increase of weak-base capacity was observed. In the solution, (CH 3) 3N, (CH 3) 2NH and CH 3NH 2 were found as the radiolytic products, their relative ratio being 15.7 : 3.7 : 1. Further, NH 3 is formed with the concentration of the same order as that of CH 3NH 2. Beside hydrogen, which is the prevailing gaseous product of the radiolysis of the mixture, methane and ethane arise, their ratio in the dynamic irradiation being 2.8 to 6.0. The main features of the radiolysis are outlined.

  18. Radiolysis of the AV-17 x 8 cs anion-exchange resin

    International Nuclear Information System (INIS)

    The mixture of the anion exchange resin AV-17 x 8 cs in borate form and of a deaerated aqueous solution containing H3BO3 and NH3 (pH = 7) was irradiated with gamma rays in both static and dynamic conditions. A loss of strong-base exchange capacity and an increase of weak-base capacity was observed. In the solution, (CH3)3N, (CH3)2NH and CH3NH2 were found as the radiolytic products, their relative ratio being 15.7: 3.7: 1. Further, NH3 is formed with the concentration of the same order as that of CH3NH2. Beside hydrogen, which is the prevailing gaseous product of the radiolysis of the mixture, methane and ethane arise, their ratio in the dynamic irradiation being 2.8 to 6.0. The main features of the radiolysis are outlined. (author)

  19. ANION EXCHANGE CAPACITY OF CHROMATE ON MODIFIED ZEOLITE CLINOPTILOLITE WITH HDTMA-Br AND ITS REGENERATION

    Directory of Open Access Journals (Sweden)

    Widajanti Wibowo

    2011-04-01

    Full Text Available Zeolite Clinoptilolite from Lampung, located in South of Sumatra, had been modified with surfactanthexadecyltrimethylammonium bromide (HDTMA-Br as chromate anion exchanger. Surfactant modified zeolite (SMZClinoptilolite in particle size range of 1.5 - 2.0 mm, which contained 196.7 mmol HDTMA-Br/kg zeolite, was used foranion exchange of chromate at neutral pH. This experiment was conducted in a glass column filled with 5 gram SMZ.The breakthrough chromate exchange capacity was found 1.262 mg/g SMZ, while the total capacity was found 2.107mg/g SMZ. The regeneration of SMZ saturated with chromate was conducted using a mixed solutions of 0.28 MNa2CO3 and 0.5 M NaOH, compared with using a solution of 0.01 M Na2S2O4. The desorption of chromate achieved92% with the mixed solutions of Na2CO3 and NaOH and 90% with the Na2S2O4 solution. The regenerated SMZ withNa2CO3-NaOH solutions was prior washed with HCl solution to remove the carbonate from SMZ, before being used forchromate sorption again. Its breakthrough capacity was reduced to 1.074 mg/g SMZ, and to 0.724 mg/g SMZ whenregenerated with Na2S2O4 solution. These results indicated that regeneration of SMZ affected its exchange capacity foranion chromate. However, it is still could be acceptable, when Na2CO3/NaOH solutions were used for the regenerationof SMZ saturated with anion chromate.

  20. Chlorine isotope effects in ion exchange reactions with a strongly basic anion exchanger

    International Nuclear Information System (INIS)

    As can be shown by the results of this study, the chemical preenrichment of the stable chlorine isotopes in inorganic ion-exchange equilibria is feasible in principle. This process should be performed in chromotographic separation columns at temperatures as low as possible. Because of the dependence of the isotopic effect on the elution medium concentration a very low concentration is desirable for the chemical enrichment process. Smaller elution concentrations however result in increasingly longer elution times. (HK)

  1. Evaluation of anion exchange resins for plutonium-uranium separations in nitric acid

    International Nuclear Information System (INIS)

    Pellicular, macroreticular and microreticular (gel type) anion exchange resins were compared for separation of plutonium from nitric acid solutions of mixed plutonium-uranium. All the macroreticular resins were 20 to 50 mesh beads. Dowex 1-X4 gel resin was 50 to 80 mesh beads. The resins were held in glass columns with coarse glass frits at the bottom of the columns. The top of the columns contained 50 ml reservoirs. The flow rates were controlled at 4 cm3.min-1.cm-2. One-centimeter bore columns with 15-cm resin bed heights were used for the plutonium elution and breakthrough capacity experiments, whereas 1.7 cm bore columns with 20 cm bed heights were used for the uranium washing experiments. As Pellionex SAX (pellicular resin) and Amberlite IRA-93 (weak base macroreticular anion exchange resin) were found to have better uranium washing and plutonium eluating characteristics than any of the resins tested. However, the capacity of the pellicular resin was much lower than that of the other resins. (T.G.)

  2. Removal of americium from effluent generated during the purification of plutonium by anion exchange

    Energy Technology Data Exchange (ETDEWEB)

    Noronha, Donald M.; Pius, Illipparambil C.; Chaudhury, Satyajeet [Bhabha Atomic Research Centre, Mumbai (India). Fuel Chemistry Div.

    2015-07-01

    Studies have been carried out on removal of americium from the effluent generated during anion exchange purification of plutonium. Americium 241, generated by the beta decay of Plutonium-241, is the major source of a activity in this highly acidic effluent and its removal would render the waste easily disposable. A simple and effective co-precipitation method, using thorium oxalate has been investigated for the treatment of this alpha active aqueous waste. Experiments have been carried out to identify optimum conditions to obtain high percentage co-precipitation with minimum amount of co-precipitant. Efforts were carried out to correlate the optimum conditions of co-precipitation of americium obtained in these experiments with solubility of thorium oxalate and americium oxalate calculated from solubility products of these compounds, stability constants of thorium and americium oxalate complexes taken from literature. The saturation capacity of thorium oxalate for Am(III) was also calculated by analyzing the K{sub d} value data using Langmuir adsorption equation. The strong tendency of americium to get co-precipitated and the high capacity exhibited by thorium oxalate for the uptake of americium indicate feasibility of using this method for the treatment of anion exchange effluent.

  3. Qualification of Reillex{trademark} HPQ anion exchange resin for use in SRS processes

    Energy Technology Data Exchange (ETDEWEB)

    Crooks, W.J. III

    2000-05-18

    The Phase 2 portion of the HB-Line facility was built in the early 1980's to process plutonium and neptunium from nitric acid solutions into oxide suitable for storage in a vault. Although the other portions of HB-Line were started up in the mid 1980's and have operated since that time, the anion exchange and precipitation processes in Phase 2 were never started up. As part of the material stabilization efforts, Phase 2 is currently being started up. A new anion exchange resin is needed because the resins that were proposed for use 10 years ago are limited by performance characteristics, disposal requirements, or are no longer commercially available. SRTC is responsible for qualifying all resins prior to their use in Nuclear Materials Stabilization and Storage (NMSS) processes. Qualification consists of both process suitability and thermal stability with nitric acid. This report describes the thermal stability qualification of Reillex{trademark} HPQ, the new resin proposed for processing plutonium and neptunium in the HB Line facility.

  4. Use of Anion Exchange Resins for One-Step Processing of Algae from Harvest to Biofuel

    Directory of Open Access Journals (Sweden)

    Martin Poenie

    2012-07-01

    Full Text Available Some microalgae are particularly attractive as a renewable feedstock for biodiesel production due to their rapid growth, high content of triacylglycerols, and ability to be grown on non-arable land. Unfortunately, obtaining oil from algae is currently cost prohibitive in part due to the need to pump and process large volumes of dilute algal suspensions. In an effort to circumvent this problem, we have explored the use of anion exchange resins for simplifying the processing of algae to biofuel. Anion exchange resins can bind and accumulate the algal cells out of suspension to form a dewatered concentrate. Treatment of the resin-bound algae with sulfuric acid/methanol elutes the algae and regenerates the resin while converting algal lipids to biodiesel. Hydrophobic polymers can remove biodiesel from the sulfuric acid/methanol, allowing the transesterification reagent to be reused. We show that in situ transesterification of algal lipids can efficiently convert algal lipids to fatty acid methyl esters while allowing the resin and transesterification reagent to be recycled numerous times without loss of effectiveness.

  5. Separation of boron isotopes in anion exchange resin column. Isotopic enrichment of 10 B

    International Nuclear Information System (INIS)

    The separation of boron isotopes (10 B and 11 B) was carried out by isotopic exchange reaction between boric acid in solution and borate/poly borate anions adsorbed on an ammonium quaternary (Dowex 1 X 8 and 2 X 8) anion exchange resin packed in columns. Each resin column had 100 cm length and 1.4 cm in diameter. The columns were connected in series during displacement of boric bands. The enrichment line used pressure ranging from 2.5 to 3.0 Kg f.cm-2. N2 gas was used as in inert atmosphere in order to prevent C O2 formation. Enrichments in 10 B of 43% were obtained using Dowex 1 X 8 resin, 0.1 eq.L-1 H3 B O3 solution and band displacement of 1,876 cm. With Dowex 2 X 8 the enrichment was 40% with 1,330 cm of band displacement and 0.1 eq. L-1 H3 B O3. The boron isotopes were analysed, as methyl borate, by mass spectrometry. (author). 13 refs, 5 figs, 2 tabs

  6. Removal of americium from effluent generated during the purification of plutonium by anion exchange

    International Nuclear Information System (INIS)

    Studies have been carried out on removal of americium from the effluent generated during anion exchange purification of plutonium. Americium 241, generated by the beta decay of Plutonium-241, is the major source of a activity in this highly acidic effluent and its removal would render the waste easily disposable. A simple and effective co-precipitation method, using thorium oxalate has been investigated for the treatment of this alpha active aqueous waste. Experiments have been carried out to identify optimum conditions to obtain high percentage co-precipitation with minimum amount of co-precipitant. Efforts were carried out to correlate the optimum conditions of co-precipitation of americium obtained in these experiments with solubility of thorium oxalate and americium oxalate calculated from solubility products of these compounds, stability constants of thorium and americium oxalate complexes taken from literature. The saturation capacity of thorium oxalate for Am(III) was also calculated by analyzing the Kd value data using Langmuir adsorption equation. The strong tendency of americium to get co-precipitated and the high capacity exhibited by thorium oxalate for the uptake of americium indicate feasibility of using this method for the treatment of anion exchange effluent.

  7. The recovery of zinc from hot galvanizing slag in an anion-exchange membrane electrolysis reactor

    International Nuclear Information System (INIS)

    This paper reports the optimization of the process parameters for recovery of zinc from hot galvanizing slag in an anion-exchange membrane electrolysis reactor. The experiments were carried out in an ammoniacal ammonium chloride system. The influence of composition of electrolytes, pH, stirring rate, current density and temperature, on cathodic current efficiency, specific power consumption and anodic dissolution of Zn were investigated. The results indicate that the cathode current efficiency increases and the hydrogen evolution decreased with increasing the cathode current density. The partial current for electrodeposition of Zn has liner relationship with ω1/2 (ω: rotation rate). The highest current efficiency for dissolving zinc was obtained when NH4Cl concentration was 53.46 g L-1 and the anodic dissolution of zinc was determined by mass transfer rate at stirring rate 0-300 r min-1. Increase in temperature benefits to improve CE and dissolution of Zn, and reduce cell voltage. Initial pH of electrolytes plays an important role in the deposition and anodic dissolution of Zn. The results of single factor experiment show that about 50% energy consumption was saved for electrodeposition of Zn in the anion-exchange membrane electrolysis reactor.

  8. A novel self-adaptive microalgae photobioreactor using anion exchange membranes for continuous supply of nutrients.

    Science.gov (United States)

    Fu, Qian; Chang, Hai-Xing; Huang, Yun; Liao, Qiang; Zhu, Xun; Xia, Ao; Sun, Ya-Hui

    2016-08-01

    A novel self-adaptive microalgae photobioreactor using anion exchange membranes (AEM-PBR) for continuous supply of nutrients was proposed to improve microalgae biomass production. The introduction of anion exchange membranes to the PBR can realize continuous supply of nutrients at desired rates, which is beneficial to the growth of microalgae. The results showed that the maximum biomass concentration obtained in the AEM-PBR under continuous supply of nitrogen at an average rate of 19.0mgN/L/d was 2.98g/L, which was 129.2% higher than that (1.30g/L) in a PBR with all the nitrogen supplied in batch at initial. In addition, the feeding rates of nitrogen and phosphorus were optimized in the AEM-PBR to maximize biomass production. The maximum biomass concentration of 4.38g/L was obtained under synergistic regulation of nitrogen and phosphorus feeding rates at 19.0mgN/L/d and 4.2mgP/L/d. The AEM-PBR demonstrates a promising approach for high-density cultivation of microalgae. PMID:27187567

  9. Isotope Fractionation of chlorine in Aqueous System: One Study on Anion-Exchange Chromatography.

    Science.gov (United States)

    Musashi, M.; Oi, T.; Eggenkamp, H.; Van Cappellen, P.

    2001-05-01

    Stable chlorine isotopes such as 37Cl and 35Cl have been paid attention as useful tool identifying the source, and monitoring the transport process and natural fate of chlorinated organic pollutants in air and groundwater. However, it is not established yet whether any isotope effects accompany biodegradation or reductive dehalogenation of the pollutants (Clark and Fritz, 1997). Here we first present an experimental determination of isotope fractionation factor of chlorine in aqueous system by using anion-exchange chromatographic technique. Into the Cl-free anion exchange resin (Muromac, OH- form) packed in a 30 cm long pyrex glass column and controlled temperature at 25 oC, hydrochloric solution was fed with controlling the flow rate constant. Effluent from the column was recovered by an automatic fraction collector and prepared for Cl isotope analysis. The Cl isotope ratio (δ 37Cl vs. SMOC) was measured by IR-MS at the Utrecht University with precision of 0.06 per-mil. Magnitude of the factor obtained was 1.00035 at 25 oC. The result indicates that the lighter isotope (35Cl) was preferably fractionated into the resin phase, while the heavier one (37Cl) was enriched into the aqueous phase. This trend suggests that molecular structure of hydrolysis with Cl in aqueous phase may be more stable than that of Cl ionically bonding with the resin. This result may offer physico-chemical insights into behavior and fate of the pollutants.

  10. Primary structure of a sperm cell anion exchanger and its messenger ribonucleic acid expression during spermatogenesis.

    Science.gov (United States)

    Holappa, K; Mustonen, M; Parvinen, M; Vihko, P; Rajaniemi, H; Kellokumpu, S

    1999-10-01

    Chloride/bicarbonate (Cl-/HCO(3)-) exchangers are a family of proteins (anion exchanger [AE] gene family) that regulate many vital cellular processes such as intracellular pH, cell volume, and Cl- concentration. They may also be involved in the regulation of sperm cell motility and acrosome reaction during fertilization, as these two phenomena are bicarbonate dependent, and we have previously shown that a polypeptide immunologically related to erythrocyte band 3 is expressed in mammalian sperm cells. We have now identified this putative sperm cell anion exchanger as the AE2 isoform of this gene family. First, we determined its complete primary structure from the human testis lambda gt 11 cDNA library. The cloned sequence was found to consist of 3896 base pairs (bp) with an open reading frame of 3726 bp, and to be almost identical to the previously published human genomic AE2 sequence. Only four amino acid disparities were found between these two sequences. Second, our in situ hybridization analyses showed that AE2 mRNA is expressed in developing sperm cells, indicating that the cloned sequence corresponds to the sperm cell AE. Our reverse transcription-polymerase chain reaction analyses suggested further that the expression of AE2 mRNA was variable to some extent during the epithelial cell cycle. Strongest expression was observed at stages VII-XIV except for stage X, i.e., when major structural and morphological changes take place. These results suggest that the full-length AE2 isoform regulates HCO(3)- transport in mature sperm cells and thus their motility in vivo. PMID:10491633

  11. Studies on the thermal and radiolytic resistance of an anion exchanger with benzimidazole functional groups in nitric acid solution

    International Nuclear Information System (INIS)

    Thermal and radiolytic resistance of AR-01R anion exchanger containing benzimidazole groups as exchange sites in nitric acid solution has been studied. Changes in its exchange capacity (EC), structure and shape were investigated and compared with those of a commercial Amberlite IRA-900 anion exchanger with quaternary ammonium group. Compared to the IRA-900, the AR-01R anion exchanger showed significantly higher thermal resistance and its decrease in EC was less than 10% after immersion in 9 mol·dm-3 solution for 72 h. On the other hand, it was found that the EC decrease of these two anion exchangers induced by γ-ray irradiation was almost the same; their EC decreased by 20-25% after irradiation in 9 mol·dm-3 HNO3 solution at room temperature with absorption dose of 3.0 MGy. The change of the strong-base benzimidazole group to weak-base benzimidazole group in AR-01 was found to be the main damage by heat and γ-ray irradiation. (author)

  12. Separation of phenolic acids from natural plant extracts using molecularly imprinted anion-exchange polymer confined ionic liquids.

    Science.gov (United States)

    Bi, Wentao; Tian, Minglei; Row, Kyung Ho

    2012-04-01

    Polymer-confined ionic liquids were used for the separation of phenolic acids from natural plant extract by utilizing an anion-exchange mechanism. They were synthesized using molecular imprinting technique to reduce non-directional ion-ion interactions during anion-exchange and other interactions with interference substances that could decrease selectivity. A suitable sorbent for phenolic acid separation could be identified based on the adsorption behaviors of phenolic acids on different polymer-confined ionic liquids. Thus, the developed ionic liquid-based molecularly imprinted anion-exchange polymer (IMAP) achieved high recovery rates by solid-phase extraction of phenolic acids from Salicornia herbacea L. extract: 90.1% for protocatechuic acid, 95.5% for ferulic acid and 96.6% for caffeic acid. Moreover, the phenolic acids were separable from each other by repeated solid phase extraction cycles. The proposed method could be used to separate other phenolic acids or organic acids from complex samples. PMID:21903215

  13. Separation of rare earths in nitric acid medium by a novel silica-based pyridinium anion exchange resin

    International Nuclear Information System (INIS)

    To separate rare earths in nitric acid medium by anion exchange process, a novel silica-based macro-reticular anion exchange resin (SiPyR-N4) with pyridinium as functional group has been synthesized. It was found that the SiPyR-N4 resin exhibits a quite strong adsorption for some rare earths especially the light rare earth elements such as La, Ce, Pr, Nd and Pm whose distribution coefficients onto SiPyR-N4 reach 10-25 dm3/kg-resin, which are much higher than the reported values for these elements with conventional anion exchange resins. The results from the column experiments show that the rare earths can be separated into the three groups: light, moderate and heavy rare earths and, a perfect separation between La-Pr group and Sm-Gd group can be achieved

  14. Impregnation process of insoluble cobalt ferrocyanide onto anion-exchange fiber prepared by radiation-induced graft polymerization

    International Nuclear Information System (INIS)

    The impregnation process of insoluble cobalt hexacyanidoferrate(II) onto an anion-exchange fiber was clarified. Vinylbenzyl trimethylammonium chloride and N-vinyl pyrrolidone were cograft-polymerized onto a 6-nylon fiber with an average diameter of 40 μm to obtain an anion-exchange capacity of 0.61 mmol/g. Hexacyanidoferrate(II) ions were adsorbed onto the anion-exchange fiber uniformly across the fiber. Subsequently, by immersing the fiber into cobalt chloride solution, hexacyanidoferrate(II) ions were quantitatively reacted with cobalt ions to form a precipitate at the periphery of the fiber. No leakage of this precipitate to the external solution was detected. The impregnation percentage, defined as the mass content of the precipitate in the resultant fiber, was 6.6%. (author)

  15. Separation of Fe (III) ions from acidic leach liquor of metasummatite Saghand ore by anion exchange resins

    International Nuclear Information System (INIS)

    Ferric ions in dilute acidic leach liquor of uranium ore of Saghand were separated by anion exchange resins. In this research, a simulated solution similar to the actual leach liquor of Saghand was prepared. The simulated solution which was containing chloride and ferric ions. rare earth elements, and some other impurities was treated by different types of Dowex anion exchange resins for ferric ions removal. It appeared that hydrochloric acidic concentration, resin types and particle sizes have a great impact on ferric ions adsorption. Dowex 1 X 4 (200-400 mesh) has the best adsorption of 91% in simulated solution and 79% in actual leach liquor of uranium ore of Saghand respectively

  16. Bifunctional Crosslinking Agents Enhance Anion Exchange Membrane Efficacy for Vanadium Redox Flow Batteries.

    Science.gov (United States)

    Wang, Wenpin; Xu, Min; Wang, Shubo; Xie, Xiaofeng; Lv, Yafei; Ramani, Vijay K

    2014-06-01

    A series of cross-linked fluorinated poly (aryl ether oxadiazole) membranes (FPAEOM) derivatized with imidazolium groups were prepared. Poly (N-vinylimidazole) (PVI) was used as the bifunctional cross-linking agent to: a) lower vanadium permeability, b) enhance dimensional stability, and c) concomitantly provide added ion exchange capacity in the resultant anion exchange membranes. At a molar ratio of PVI to FPAEOM of 1.5, the resultant membrane (FPAEOM-1.5 PVI) had an ion exchange capacity of 2.2 meq g-1, a vanadium permeability of 6.8×10-7 cm2 min-1, a water uptake of 68 wt.%, and an ionic conductivity of 22.0 mS cm-1, all at 25°C. Single cells prepared with the FPAEOM-1.5 PVI membrane exhibited a higher coulombic efficiency (> 92%) and energy efficiency (> 86%) after 40 test cycles in vanadium redox flow battery. The imidazolium cation showed high chemical stability in highly acidic and oxidizing vanadium solution as opposed to poor stability in alkaline solutions. Based on our DFT studies, this was attributed to the lower HOMO energy (-7.265 eV) of the HSO4- ion (compared to the OH- ion; -5.496 eV) and the larger HOMO-LUMO energy gap (6.394 eV) of dimethylimidazolium bisulfate ([DMIM] [HSO4]) as compared to [DMIM] [OH] (5.387 eV). PMID:24884171

  17. An efficient elution method of tetravalent uranium from anion exchanger by using formic acid solution

    International Nuclear Information System (INIS)

    In recent years, we have been investigating the development of the ERIX (The Electrolytic Reduction and Ion Exchange) process for reprocessing spent FBR-MOX fuel. This process uses electrolytic reduction and ion exchange techniques to recover U, Pu from spent FBR-MOX fuel solution. It was found that despite of the high nitric acid concentration, U(VI) can be effectively reduced to U(IV) using a flow type electrolytic cell in the existence of hydrazine and the U(IV) can be completely separated from fission products by the anion exchanger, AR-01. In addition, it was proposed that a part of U is assigned to be recovered together with Pu and Np for reusing as a FBR-MOX fuel. For that purpose, we are investigating an efficient elution method of Pu(IV) and U(IV) from AR-01. In this work, to develop an efficient elution method of U(IV) from AR-01, we have examined the U(IV) elution behavior by formic acid and the complex-formation of U(IV) with HCOO-

  18. Fixation by anion exchange of toxic materials in a glass matrix

    International Nuclear Information System (INIS)

    This invention relates to the immobilization of toxic, e.g., radioactive materials, internally in a silicate glass or silica gel matrix for extremely long periods of time. Toxic materials, such as radioactive wastes containing radioactive anions, and in some cases cations, which may be in the form of liquids, or solids dissolved or dispersed in liquids or gases, are internally incorporated into a glass matrix, having hydrous organofunctionalsiloxy groups, E.G., hydrous aminoalkylsiloxy or carboxyorganosiloxy, bonded to silicon atoms of said glass and/or hydrous polyvalent metals bonded to silicon atoms of said glass through divalent oxygen linkages or otherwise immobilized therein, by a process which involves the ion exchange of said toxic, radioactive anions with hydroxyl groups attached to said organofunctionalsiloxy groups or with hydroxyl groups attached to the hydrous polyvalent metal. Thereafter, the resulting glass now characterized by a distribution of internally bonded or immobilized, toxic, radioactive anions can be packaged in suitable containers, and disposed of as by burial, and/or they can be sintered to collapse the pores thereof prior to disposal or for producing useful radiation sources. The porous glass or a porous silica gel having said silicon-bonded organofunctionalsiloxy groups and/or said hydrous polyvalent metal oxy groups, the pores of said glass or silica gel remaining open and uncollapsed, can be used advantageously as a backfill for an underground radioactive waste burial site and as overpack in the waste disposal container. Also included is a novel method for bonding the polyvalent metal to the porous silica glass or gel by substituting the protons of the silicon-bonded hydroxyl groups thereof with an alkali metal or ammonium cation followed by displacement of said cation with the non-radioactive polyvalent metal cation

  19. Efficient Separation of Lanthanides Using Poly (Styrene-Divinyl Benzene) Aminated Anion Exchanger

    International Nuclear Information System (INIS)

    New chromatographic method was developed for the determination and separation of lanthanides using AS4A anionic column. The behavior of the column towards lanthanides was studied through many parameters, From the data obtained it is found that, affinity of the column toward investigated ions increase by increasing eluent concentration and it decrease retention factors. With the two investigated eluent (oxalic and citric acids), elution order for lanthanide elements was obtained in their atomic number from La to Lu. Retention times and retention orders obtained at these conditions clearly show that, lanthanides in AS4A are displaced according to anion exchange mechanism. More over separation of lanthanides using AS4A was studied using isocratic and gradient elution programs. Light and the first intermediate lanthanide elements were separated successfully by applying a gradient program containing 70% oxalic acid (100 mM) and 30% water. The problem of separation for heavy and the last intermediate lanthanide elements was solved using 100 mM alpha hydroxy isobutyric acid (α-HIBA)

  20. Purification system of gram-amount neptunium using anion exchange chromatography

    International Nuclear Information System (INIS)

    To develop a purification system of gram-amount neptunium using anion exchange chromatography, adsorption elution of excess amount of actinium in 6M HNO3 aqueous solution was studied using thorium and uranium tracer. The partition coefficient (Kd) of Th (IV) decreased from Kd=99.1 of tracer to Kd=44.0, 5% load. By decreasing the partition coefficient, we can wash until 30 Vs under the purification conditions of 1% load and 95% recovery. The retention volume of U (IV) was about 300 Vs, a large value. The partition coefficient of Np (IV) may be larger than it and the large amount of washable eluting solution may be obtained. Washing of impurity of 3d transition metal and actinide (VI) can be done until 20Vs. With washing of 150Vs, impurity of alkali earth metal, metals (III) and platinum group metals decreased less than 0.1%. (S.Y.)

  1. An improved, computer-based, on-line gamma monitor for plutonium anion exchange process control

    International Nuclear Information System (INIS)

    An improved, low-cost, computer-based system has replaced a previously developed on-line gamma monitor. Both instruments continuously profile uranium, plutonium, and americium in the nitrate anion exchange process used to recover and purify plutonium at the Los Alamos Plutonium Facility. The latest system incorporates a personal computer that provides full-feature multichannel analyzer (MCA) capabilities by means of a single-slot, plug-in integrated circuit board. In addition to controlling all MCA functions, the computer program continuously corrects for gain shift and performs all other data processing functions. This Plutonium Recovery Operations Gamma Ray Energy Spectrometer System (PROGRESS) provides on-line process operational data essential for efficient operation. By identifying abnormal conditions in real time, it allows operators to take corrective actions promptly. The decision-making capability of the computer will be of increasing value as we implement automated process-control functions in the future. 4 refs., 6 figs

  2. Magnetic graphitic carbon nitride anion exchanger for specific enrichment of phosphopeptides.

    Science.gov (United States)

    Zhu, Gang-Tian; He, Xiao-Mei; Chen, Xi; Hussain, Dilshad; Ding, Jun; Feng, Yu-Qi

    2016-03-11

    Anion-exchange chromatography (AEX) is one of the chromatography-based methods effectively being used for phosphopeptide enrichment. However, the development of AEX materials with high specificity toward phosphopeptides is still less explored as compared to immobilized metal affinity chromatography (IMAC) or metal oxide affinity chromatography (MOAC). In this work, magnetic graphitic carbon nitride (MCN) was successfully prepared and introduced as a promising AEX candidate for phosphopeptide enrichment. Due to the extremely abundant content of nitrogen with basic functionality on the surface, this material kept excellent retention for phosphopeptides at pH as low as 1.8. Benefiting from the large binding capacity at such low pH, MCN showed remarkable specificity to capture phosphopeptides from tryptic digests of standard protein mixtures as well as nonfat milk and human serum. In addition, MCN was also applied to selective enrichment of phosphopeptides from the tryptic digests of rat brain lysate and 2576 unique phosphopeptides were successfully identified. PMID:26884140

  3. Determination of metallic impurities in uranium through anion exchange separation and neutron activation analysis

    International Nuclear Information System (INIS)

    The separation of metals from uranium by anionic exchange was studied. The behaviour of ions in Dowex 1x8 in HNO3, H2SO4, HC1, HCL-HF, and NH3 media and Dowex 2x8 in H2SO4 medium were investigated. Methods for the separation of Na, Mg, Al, K, Ca, Sc, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Rb, Zr, Ag, Cd, Cs, Ba, La, Ce, Nd, Sm, Eu, Tb, Yb, La, Hf and Th were developed. For Mo, partial separation was obtained. Separation schemes for the neutron activation analysis of metallic impurities in uranium are proposed. The detection limits are given. The results for the elements Al, Cr, Mn, Co, Ni, Cu, V and Fe determined from the IAEA reference samples SR-54/64 are compared with recommended values

  4. REMOVAL OF GLUCORAPHENIN FROM THE EXTRACT OF RADISH PIGMENT BY ANION EXCHANGE RESIN 201×7

    Institute of Scientific and Technical Information of China (English)

    ZhouXiaohua; ChenQi

    1998-01-01

    A method for removimg glucoraphenin from the extract of Radish pigment by anion exchange resin 201×7 was studied.The adsorption capacity of 201×7 resin for glucoraphenin was 72.8mg/ml resin,the equilibrium time 55 minutes,and the optinum pH5.5.All glucoraphenin that had been adsorbed on 201×7 resin was eluted by 1.5BV.hr-1, eluent in whinc concentration of NaOH was 0.05mol·L-1 at the flow rate of 1.5BV/h.Extracting solution of deglucoraphenin was enriched by vacuum and spray drying.A powder product of Radish pigment was obtained and E1cm1%=4.30.

  5. Collaborative study of an anion exchange method for the determination of trace plutonium in water

    International Nuclear Information System (INIS)

    A single-laboratory evaluation and an interlaboratory collaborative study were made of a method for determining plutonium in water. The method was written for the analysis of one-liter samples and involves coprecipitation, acid dissolution, anion exchange, electrodeposition, and alpha pulse height analysis. After the single-laboratory evaluation of the selected method, four samples were prepared for the collaborative study: two river-water samples, a substitute ocean water sample, and sample containing sediment. These samples contained plutonium-239 and plutonium-238 at concentrations ranging from 0.42 to 28.9 dis/min/liter. In the collaborative study standard deviations of plutonium concentrations ranged from 5 to 13%. In three cases, standard deviations agreed with those expected from counting statistics. It is believed that hydrolysis occurred in the river water samples resulting in errors greater than those expected from counting statistics

  6. Synthesis and Properties of Anion Exchangers Derived from Chloromethyl Styrene Codivinylbenzene and Their Use in Water Treatment

    Directory of Open Access Journals (Sweden)

    Hesham A. Ezzeldin

    2010-01-01

    Full Text Available Amination of vinylbenzyl chloride-divinylbenzene (VBC-DVB copolymers is an effective method for preparation of ion-exchange resins. Conventionally, the starting polymer is produced by chloromethylation of a styrene-divinylbenzene copolymer that utilizes chloromethyl methyl ether, a known carcinogen. An alterative approach is to copolymerize vinylbenzyl chloride with divinylbenzene to generate the necessary VBC-DVB. This method provides precise control over the density of the ion-exchange groups. The regiochemistry of the vinylbenzyl chloride methods was realized using solvent-ion exchange groups. In this investigation, an improved solvent system was found for the preparation of anion exchange resins by the vinylbenzyl chloride route. The effectiveness of amination of the intermediate VBC-DVB polymers with a variety of trimethylamine reagents was investigated, and ethanolic trimethylamine produced the highest degree of amination. These resulting ion-exchange polymers were characterized by a variety of techniques such as analytical titrations, nitrogen analysis, Fourier transform infrared spectroscopy and thermal gravimetric analysis. Testing of these copolymers for breakthrough was performed. The results indicate that these anion exchangers have a meaningful increase in thermal stability over commercial anionic exchange beads.

  7. Synthesis and Properties of Anion Exchangers Derived from Chloromethyl Styrene Co divinylbenzene and Their Use in Water Treatment

    International Nuclear Information System (INIS)

    Amination of vinylbenzyl chloride-divinylbenzene (VBC-DVB) copolymers is an effective method for preparation of ion-exchange resins. Conventionally, the starting polymer is produced by chloromethylation of a styrene-divinylbenzene copolymer that utilizes chloromethyl methyl ether, a known carcinogen. An alterative approach is to co polymerize vinylbenzyl chloride with divinylbenzene to generate the necessary Vb-Dvb. This method provides precise control over the density of the ion-exchange groups. The regiochemistry of the vinylbenzyl chloride methods was realized using solvent-ion exchange groups. In this investigation, an improved solvent system was found for the preparation of anion exchange resins by the vinylbenzyl chloride route. The effectiveness of amination of the intermediate VBC-DVB polymers with a variety of trimethylamine reagents was investigated, and ethanolic trimethylamine produced the highest degree of amination. These resulting ion-exchange polymers were characterized by a variety of techniques such as analytical titrations, nitrogen analysis, Fourier transform infrared spectroscopy and thermal gravimetric analysis. Testing of these copolymers for breakthrough was performed. The results indicate that these anion exchangers have a meaningful increase in thermal stability over commercial anionic exchange beads

  8. Imidazolium-Based Polymeric Materials as Alkaline Anion-Exchange Fuel Cell Membranes

    Science.gov (United States)

    Narayan, Sri R.; Yen, Shiao-Ping S.; Reddy, Prakash V.; Nair, Nanditha

    2012-01-01

    Polymer electrolyte membranes that conduct hydroxide ions have potential use in fuel cells. A variety of polystyrene-based quaternary ammonium hydroxides have been reported as anion exchange fuel cell membranes. However, the hydrolytic stability and conductivity of the commercially available membranes are not adequate to meet the requirements of fuel cell applications. When compared with commercially available membranes, polystyrene-imidazolium alkaline membrane electrolytes are more stable and more highly conducting. At the time of this reporting, this has been the first such usage for imidazolium-based polymeric materials for fuel cells. Imidazolium salts are known to be electrochemically stable over wide potential ranges. By controlling the relative ratio of imidazolium groups in polystyrene-imidazolium salts, their physiochemical properties could be modulated. Alkaline anion exchange membranes based on polystyrene-imidazolium hydroxide materials have been developed. The first step was to synthesize the poly(styrene-co-(1-((4-vinyl)methyl)-3- methylimidazolium) chloride through a free-radical polymerization. Casting of this material followed by in situ treatment of the membranes with sodium hydroxide solutions provided the corresponding hydroxide salts. Various ratios of the monomers 4-chloromoethylvinylbenzine (CMVB) and vinylbenzine (VB) provided various compositions of the polymer. The preferred material, due to the relative ease of casting the film, and its relatively low hygroscopic nature, was a 2:1 ratio of CMVB to VB. Testing confirmed that at room temperature, the new membranes outperformed commercially available membranes by a large margin. With fuel cells now in use at NASA and in transportation, and with defense potential, any improvement to fuel cell efficiency is a significant development.

  9. Efficient defluoridation of water using reusable nanocrystalline layered double hydroxides impregnated polystyrene anion exchanger.

    Science.gov (United States)

    Cai, Jianguo; Zhang, Yanyang; Pan, Bingcai; Zhang, Weiming; Lv, Lu; Zhang, Quanxing

    2016-10-01

    Water decontamination from fluoride is still a challenging task of global concern. Recently, Al-based layered double hydroxides (LDHs) have been extensively studied for specific fluoride adsorption from water. Unfortunately, they cannot be readily applied in scaled-up application due to their ultrafine particles as well as the regeneration issues caused by their poor stability at alkaline pHs. Here, we developed a novel (LDH)-based hybrid adsorbent, i.e., LALDH-201, by impregnating nanocrystalline Li/Al LDHs (LADLH) inside a commercial polystyrene anion exchanger D201. TEM image and XRD spectra of the resultant nanocomposite confirmed that the LDHs particles were nanosized inside the pores of D201 of highly crystalline nature and well-ordered layer structure. After impregnation, the chemical and mechanical stability of LALDH were significantly improved against pH variation, facilitating its application at a wide pH range (3.5-12). Fluoride adsorption onto LALDH-201 was compared to D201 and activated alumina, evidencing the preferable removal fluoride of LALDH-201. Fluoride adsorption onto LALDH-201 followed pseudo-second-order model, with the maximum capacity (62.5 mg/g from the Sips model) much higher than the other two adsorbents. Fixed-bed adsorption run indicated the qualified treatable volume of the fluoride contaminated groundwater (4.1 mg/L initially) with LALDH-201 was about 11 times as much as with the anion exchanger D201 when the breakthrough point was set as 1.5 mg/L. The capacity of LALDH-201 could be effectively refreshed for continuous column operation without observable loss by using the mixed solution of 0.01 M NaOH + 1 M NaCl. The above results suggested that the hybrid adsorbent LALDH-201 is very promising for water defluoridation in scaled-up application. PMID:27337346

  10. Application of a weak base anion exchange resin for recovery of uranium at Uravan, Colorado, U.S.A

    International Nuclear Information System (INIS)

    Resin ion-exchange technology has been used to recover uranium at the Uravan, Colorado plant for over 18 years; however, since the end of U.S. Atomic Energy Commission purchase of U3O8 concentrate in 1970, it has become necessary to develop techniques for upgrading the product to meet the more stringent specifications of private sales. The standard gel type quaternary ammonium anion exchange resin had been used previously. The development of the tertiary amine anion exchange resin, Amberlite XE-299, led to an experimental program of laboratory and pilot plant work to evaluate the resin on actual plant solutions. General information on ion-exchange resin structure and chemistry is discussed. Summary data of specific test work on loading the resin, various elution schemes, resin regeneration and product purity from the pilot plant tests and comments on actual plant operation using Amberlite XE-299 resin are presented. (author)

  11. Electron exchange between dipole-bound anion and polar molecule and dipole-bound anions dimer formation

    International Nuclear Information System (INIS)

    We consider collision between a dipole-bound molecular anion and a neutral polar molecule and show that the excess electron can bind two neutral molecules into a dimer. Using a variational approach similar to the Heitler-London model of H''+2 ion we obtain the energy terms of such a dimer. Their difference determines the cross-section of electron transfer from the anion to the neutral molecule in quasiclassical near-resonant Born-Oppenheimer approximation. We obtain for the cross-section an analytic expression containing the weak (logarythmic) factor depending on the molecular dipole moment, and collision velocity. Our analytic calculations are in a good accordance with the results of a recent experiment.

  12. Studies on thermal stability of type I and type II anion exchange resins used for separation of isotopes of boron by ion exchange chromatography

    International Nuclear Information System (INIS)

    Thermal stability of indigenously available type I and type II anion exchange resins were studied in chloride and hydroxyl forms. The results of the study indicated that the resins under study were thermally stable up to 50 deg C even when heated in an oven for 180 days and there was no appreciable loss in ion exchange capacity of the resins for boric acid. (author)

  13. Simultaneous Determination of Anions and Cations in Natural Water by Ion-exclusion/Cation-exchange Chromatography with a Weakly Acidic Cation-exchange Resin Column

    International Nuclear Information System (INIS)

    The simultaneous determination of anions (SO4 2-, Cl-, and NO3 -) and cations (Na+, NH4+, K+, Mg2+, and Ca2+) in natural water obtained by Nakdong River waters system in Korea were performed by ion-exclusion/cation exchange chromatography with conductimetric detection. The stationary phase was a polymethacrylate-based weakly acidic cation-exchange resin column in the H+-form and a weak-acid eluent. When using only a 1.4 mM sulfosalicylic acid/6 mM 18-crown-6 ether as an eluent, good resolution of both anions and cations, minimum time required for the separation, and satisfactory detection sensitivity were obtained in a reasonable time. The method was successfully applied to the simultaneous determination of anions and cations in natural waters

  14. Simultaneous Determination of Anions and Cations in Natural Water by Ion-exclusion/Cation-exchange Chromatography with a Weakly Acidic Cation-exchange Resin Column

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Kwang Pill; Choi, Seong Ho; Park, Yu Chul; Bae, Zun Ung; Lee, Mu Sang; Lee, Sang Hak; Chang, Hye Yong [Graduate School, Kyungpook National University, Daegu (Korea, Republic of); Kwon, Se Mok [Ulsan City Health and Environmental Research Institute, Ulsan (Korea, Republic of); Tanaka, Kazuhiko [National Industrial Research Institute of Nagoya, Nagoya (Japan)

    2003-09-15

    The simultaneous determination of anions (SO{sub 4} {sup 2-}, Cl{sup -}, and NO{sub 3} {sup -}) and cations (Na{sup +}, NH{sup 4+}, K{sup +}, Mg{sup 2+}, and Ca{sup 2+}) in natural water obtained by Nakdong River waters system in Korea were performed by ion-exclusion/cation exchange chromatography with conductimetric detection. The stationary phase was a polymethacrylate-based weakly acidic cation-exchange resin column in the H{sup +}-form and a weak-acid eluent. When using only a 1.4 mM sulfosalicylic acid/6 mM 18-crown-6 ether as an eluent, good resolution of both anions and cations, minimum time required for the separation, and satisfactory detection sensitivity were obtained in a reasonable time. The method was successfully applied to the simultaneous determination of anions and cations in natural waters.

  15. Analysis of human milk oligosaccharides using high-performance anion-exchange chromatography with pulsed amperometric detection

    DEFF Research Database (Denmark)

    Lie, Aleksander; Pedersen, Lars Haastrup

    lacto-N-neotetraose (Galβ1-4GlcNAcβ1-3Galβ1-4Glc), among others. High-performance anion-exchange chromatography (HPAE) with pulsed amperometric detection (PAD) is an analysis method highly suited for carbohydrates. HPAE with alkaline eluents results in retention of neutral carbohydrates depending on the...

  16. Determination of plutonium, uranium and americium/curium isotopes in environmental samples with anion exchange, UTEVA, Sr and DGA resin

    International Nuclear Information System (INIS)

    This study presents a quantitative sequential radiochemical separation method for the Pu, U, Sr and Am/Cm isotopes with an anion exchange resin, UTEVA resin, Sr resin and DGA resin in environmental samples. After the radionuclides were leached from samples with 8M HNO3, the Pu, U, Sr and Am/Cm isotopes were sequentially adsorbed on the anion exchange column, UTEVA column connected with Sr Spec column and DGA column. The Pu isotopes were purified from other nuclides through the anion exchange column, and the uranium isotopes were separated from other nuclides through the UTEVA column. Also, 90Sr was separated from other hindrance elements such as Ca2+, Ba2+ and Y3+ with the Sr Spec column. Finally, Am/Cm fractions were purified with the DGA and anion exchange resins. After α source preparation for the purified Pu, U and Am/Cm isotopes with the micro-coprecipitation method, the Pu, U and Am/Cm isotopes were measured by an alpha spectrometry. Strontium-90 was measured by a low level liquid scintillation counter. The radiochemical procedure for Pu, U and Am nuclides investigated in this study has been validated by application to IAEA Reference soils. (orig.)

  17. Adsorption of uranium (VI) from mixed chloride-fluoride solutions by anion-exchange resins

    Energy Technology Data Exchange (ETDEWEB)

    Pakholkov, V.S.; Denisova, L.A.; Rychkov, V.N.; Kurnosenko, N.A.

    1988-03-01

    Experimental data are reported and discussed concerning the adsorption of uranium from 0.025 M solutions of UO/sub 2/Cl/sub 2/, containing HCl, HF, and NH/sub 4/Cl over a wide concentration range, using anion-exchange resins of varying basicities. UV and IR spectroscopic studies were conducted in order to clarify the chemical mechanism of uranium adsorption. Adsorption isotherms for all of the ion-exchange resins studied are convex in shape and can be described by the following equations: log K/sub d/ = a + b (-log C/sub e/), and log A = a + (b + 1) log C/sub e/, where A is the adsorptivity in mmole U/g; K/sub d/ is the distribution coefficient in mg/liter; and C/sub e/ is the equilibrium concentration of U in mmole/ml. General mathematical models have been obtained to describe the adsorption process; these consist of a system of regression equations derived from the results of a complete 2/sup 3/ factorial study.

  18. Adsorption characteristics of boric acid on strong-base anion exchange resin

    International Nuclear Information System (INIS)

    The Boron Thermal Regeneration System (BTRS) is capable of controlling boron concentration in primary coolant and reducing the amount of liquid waste at the end of fuel cycle in a pressurized water reactor, but the system has not been in effective operation yet because of the lack of detailed information regarding the boron adsorption characteristics of the ion exchange resin packed in the demineralizers of BTRS. In this study, the adsorption characteristics of boric acid on a strong-base anion exchange resin, an Amberlite IRN-78LC resin in OH- form, were investigated at temperature from 10 .deg. C to 60 .deg. C in the concentrations of boron up to 1500 ppm covering the BTRS operational conditions. A computer code was developed to calculate the composition of borate ions in solution as a function of boron concentration, temperature and pH. From the calculated composition of borate ions and experimental data of adsorption equilibrium, the model was proposed for the adsorption isotherm of boric acid on the resin. The diffusion coefficient of the boric acid in the resin was calculated by the particle diffusion model and found that the temperature dependency of the coefficient follows an Arrhenius equation. The results in this study can be applied for the optimum operation of BTRS

  19. Effect of temperature (and the degree of crosslinking) on the reactivity of anion-exchange resins by applying the OT-for-OH exchange reaction

    International Nuclear Information System (INIS)

    In order to reveal (i) the exchange ability of OT- resulting from the dissociation of HTO, (ii) the effect of temperature on the reactivity of anion-exchange resins, and (iii) the effect of the degree of crosslinking on the reactivity of the resins, the OT-for-OH exchange reaction between each OH--form anion-exchange resin and HTO water was observed in the equilibrium state. The anion-exchange resins used were Amberlite IRA-400, and Biorad AG1-X2, X4, X8. The temperature used was 20, 30, 40, 60 or 80 C. The activity of each resin based on the OT-forcounter. Analyzing the data obtained, it ws found that: (1) the higher the temperature is, the smaller is the activity of IRA-400 resin within the range of 40-80 C; (2) the larger the degree of crosslinking in each Biorad AG1 resin, the lower the activity of the resin. Accordingly, it can be concluded that: (1) as for the dissociation of HTO at high temperature, the formula (HTOT++OH-) is more predominant than the formula (HTOH++OT-); (2) the resin with lower porosity (i.e., the resin having the larger degree of crosslinking) shows a lesser tendency for the OT-for-OH exchange reaction to occur than the resin with a higher porosity. (orig.)

  20. Grafting glycidyl methacrylate to Sepharose gel for fabricating high-capacity protein anion exchangers.

    Science.gov (United States)

    Wang, Qianqian; Yu, Linling; Sun, Yan

    2016-04-22

    To develop ion exchangers of high protein adsorption capacity, we have herein introduced atom transfer radical polymerization (ATRP) method to graft glycidyl methacrylate (GMA) onto Sepharose FF gel. GMA-grafted Sepharose FF resins of four grafting densities and different grafting chain lengths were obtained by adjusting reaction conditions. The epoxy groups on the grafted chains were functionalized by modification with diethylamine (DEA), leading to the fabrication of Sepharose-based anion exchangers of 14 different grafting densities and/or grafting chain lengths. The resins were first characterized for the effects of grafting density, chain length and ionic strength on pore sizes by inverse size exclusion chromatography. Then, the resins were evaluated by adsorption equilibria of bovine serum albumin (BSA) as a function of ionic capacity (IC) (chain length) at individual grafting densities. It was observed that at each grafting density there was a specific IC value (chain length) that offered the maximum equilibrium capacity. Of the resins with maximum values at individual grafting densities, the resin of the second grafting density with an IC value of 330 mmol/L (denoted as FF-Br2-pG-D330) showed the highest capacity, 264 mg/mL, about two times higher than that of the traditional ungrafted resin Q Sepharose FF (137 mg/mL). This resin also showed the most favorable uptake kinetics among the resins of similar IC values but different grafting densities, or of the same grafting density but different IC values. Effects of ionic strength showed that the capacities of FF-Br2-pG-D330 were much higher than Q Sepharose FF at a wide range of NaCl concentrations (0-200 mmol/L), and the uptake rates of the two resins were similar in the ionic strength range. Therefore, the dynamic binding capacity values of BSA on FF-Br2-pG-D330 were much higher than Q Sepharose FF as demonstrated at different residence times and ionic strengths. Taken together, the research has proved the

  1. L(+-Lactic acid recovery from cassava bagasse based fermented medium using anion exchange resins

    Directory of Open Access Journals (Sweden)

    Rojan P. John

    2008-12-01

    Full Text Available The properties of the ion exchange resins, Amberlite IRA 402, a strong anion exchange resin and IRA 67, a weak anion exchange resin were determined to evaluate their comparative suitability for lactic acid recovery from fermented cassava bagasse. Data on binding capacities and recovery proved that weak base resin in chloride form was the most favourable ones for lactic acid recovery from aqueous solutions and fermentation media. Fermented media obtained through simultaneous saccharification and fermentation of cassava bagasse starch hydrolysate based medium were used for lactic acid recovery study using weak base resin column. Amberlite IRA 67 had much more efficiency than Amberlite IRA 402 to recover lactic acid. Like in other reports, due to the presence of nutrients and ions other than lactate, the binding capacity was slightly lesser while using fermented media (~93% instead of aqueous lactic acid solutions (~98%.As propriedades das resinas de troca iônica, da Amberlite IRA 402, uma resina de troca aniônica forte, e da IRA 67, uma resina de troca aniônica fraca, foram determinadas para se avaliar a adequabilidade comparativa delas à obtenção de ácido lático de bagaço de mandioca fermentado. Dados sobre a capacidade de ligação e sobre a obtenção provaram que a resina de base fraca na forma de cloreto era a mais adequada para a obtenção de ácido lático em soluções aquosas e meios de fermentação. Os meios de fermentação obtidos da sacarificação e da fermentação simultâneas de meios baseados hidrolisados de fécula de bagaço de mandioca foram usados para o estudo da obtenção de ácido lático usando uma coluna de resina de base fraca. A Amberlite IRA 67 mostrou-se muito mais eficaz do que a Amberlite IRA 402 para a obtenção de ácido lático. Como em outros relatórios, devido à presença de nutrientes e íons que não lactatos, a capacidade de ligação foi ligeiramente inferior enquanto se utilizavam meios

  2. High-Capacity and Rapid Removal of Refractory NOM Using Nanoscale Anion Exchange Resin.

    Science.gov (United States)

    Johnson, Billy R; Eldred, Tim B; Nguyen, Andy T; Payne, William M; Schmidt, Emily E; Alansari, Amir Y; Amburgey, James E; Poler, Jordan C

    2016-07-20

    As human health concerns over disinfection byproducts (DBP) in drinking water increase, so does the need to develop new materials that remove them rapidly and at high capacity. Ion exchange (IEX) is an effective method for the removal of natural organic matter (NOM), especially anion exchange resins (AERs) with quaternary ammonium functional groups. However, capacity is limited in existing commercial resin materials because adsorbates can only interact with the outermost surface area, which makes these products inefficient on a mass basis. We have synthesized a novel "NanoResin" exploiting the enhanced NOM removal of the quaternary ammonium resin while utilizing the vast surface area of SWCNTs, which act as scaffolding for the resin. Our nanomaterials show increased adsorption capacity compared to commercially available adsorbents, in a fraction of the time. This NanoResin requires only about 10 s to reach ion-exchange equilibrium. Comparatively, commercial AERs only achieved partial removal after more than 30 min. High capacity adsorption of a low molecular weight (MW) surrogate has been measured. NOM removal was demonstrated in solutions of both low and high specific UV absorbance (SUVA) composition with these nanomaterials. Additionally, the NanoResin showed enhanced removal of a NOM concentrate sample taken from Myrtle Beach, SC, demonstrating NanoResin is an effective method of removal for refractory NOM in a natural aqueous environment. Synthesis and characterization of the polymers and nanomaterials are presented below. Adsorption capacity, adsorption kinetics, and the regeneration and reusability of these new materials for NOM removal are described. The open matrix microstructure precludes any intraparticle diffusion of adsorbates; thus, these nanomaterials act as a "contact resin". PMID:27348616

  3. Dowex anion exchanger-loaded-baker's yeast as bi-functionalized biosorbents for selective extraction of anionic and cationic mercury(II) species

    International Nuclear Information System (INIS)

    Dowex anion exchanger-immobilized-baker's yeast [Dae-yeast] were synthesized and potentially applied as environmental friendly biosorbents to evaluate the up-take process of anionic and cationic mercury(II) species as well as other metal ions. Optimization of mass ratio of Dowex anion exchanger versus yeast (1:1-1:10) in presence of various interacting buffer solutions (pH 4.0-9.0) was performed and evaluated. Surface modification of [Dae-yeast] was characterized by scanning electron microscopy (SEM) and infrared spectroscopy. The maximum metal biosorption capacity values of [Dae-yeast] towards mercury(II) were found in the range of 0.800-0.960, 0.840-0.950 and 0.730-0.900 mmol g-1 in presence of buffer solutions pH 2.0, 4.0 and 7.0, respectively. Three possible and different mechanisms are proposed to account for the biosorption of mercury and mercuric species under these three buffering conditions based on ion exchange, ion pair and chelation interaction processes. Factors affecting biosorption of mercury from aqueous medium including the pH effect of aqueous solutions (1.0-7.0), shaking time (1-30 min) and interfering ions were searched. The potential applications of modified biosorbents for selective biosorption and extraction of mercury from different real matrices including dental filling waste materials, industrial waste water samples and mercury lamp waste materials were also explored. The results denote to excellent percentage extraction values, from nitric acid as the dissolution solvent with a pH 2.0, as determined in the range of 90.77-97.91 ± 3.00-5.00%, 90.00-93.40 ± 4.00-5.00% and 92.31-100.00 ± 3.00-4.00% for the three tested samples, respectively.

  4. Model of a vanadium redox flow battery with an anion exchange membrane and a Larminie-correction

    Science.gov (United States)

    Wandschneider, F. T.; Finke, D.; Grosjean, S.; Fischer, P.; Pinkwart, K.; Tübke, J.; Nirschl, H.

    2014-12-01

    Membranes are an important part of vanadium redox flow battery cells. Most cell designs use Nafion®-type membranes which are cation exchange membranes. Anion exchange membranes are reported to improve cell performance. A model for a vanadium redox flow battery with an anion exchange membrane is developed. The model is then used to calculate terminal voltages for open circuit and charge-discharge conditions. The results are compared to measured data from a laboratory test cell with 40 cm2 active membrane area. For higher charge and discharge currents, an empirical correction for the terminal voltage is proposed. The model geometry comprises the porous electrodes and the connected pipes, allowing a study of the flow in the entrance region for different state-of-charges.

  5. Sodium citrate-assisted anion exchange strategy for construction of Bi2O2CO3/BiOI photocatalysts

    International Nuclear Information System (INIS)

    Highlights: • Heterostructured Bi2O2CO3/BiOI microspheres were prepared via anion exchange. • Sodium citrate-assisted anion exchange for construction of composite photocatalysts. • Bi2O2CO3/BiOI composites show high visible light photocatalytic activity. - Abstract: Bi2O2CO3/BiOI heterojuncted photocatalysts were constructed through a facile partial anion exchange strategy starting from BiOI microspheres and urea with the assistance of sodium citrate. The content of Bi2O2CO3 in the catalysts was regulated by modulating the amount of urea as a precursor, which was decomposed to generate CO32− in the hydrothermal process. Citrate anion plays a key role in controlling the morphology and composition of the products. The Bi2O2CO3/BiOI catalysts display much higher photocatalytic activity than pure BiOI and Bi2O2CO3 towards the degradation of rhodamine B (RhB) and bisphenol A (BPA). The enhancement of photocatalytic activity of the heterojuncted catalysts is attributed to the formation of p–n junction between p-BiOI and n-Bi2O2CO3, which is favorable for retarding the recombination of photoinduced electron-hole pairs. Moreover, the holes are demonstrated to be the main active species for the degradation of RhB and BPA

  6. Development and characterization of direct ethanol fuel cells using alkaline anion-exchange membranes

    Science.gov (United States)

    Lim, Peck Cheng

    2009-08-01

    Alkaline membrane fuel cell (AMFC) is a relatively new fuel cell technology that is generating considerable interests. It offers the electrocatalytic advantages of conventional alkaline fuel cells, and the manufacturing and cost advantages of solid polymer electrolyte fuel cells. This project was carried out to develop and characterize high performance membrane electrode assemblies (MEAs) for all-solid-state AMFCs. The primary fuel of interests is ethanol, but hydrogen was used in the development stages to facilitate the diagnostic and evaluation of the fuel cell performance. In the preliminary investigation, AMFC was assembled using off-the-shelf electrodes and anion-exchange membrane (AEM). It was found that the performance of AMFC operating on ethanol fuel was limited by a large high-frequency resistance (HFR) value. The advantage of using non-toxic ethanol fuel was also compromised by the need to add hydrazine and potassium hydroxide to the fuel blend. Subsequently, a high performance MEA was developed for an all-solid-state AMFC, in which liquid electrolyte or other additives were not required during the operation of the fuel cell. Ionomer was incorporated in the formulation of catalyst ink, and the catalyst ink was directly coated on the anion-exchange membrane (AEM). An ionomer content of 20 wt.% was found to be the optimum amount required in the catalyst layers. It was demonstrated that the AMFC generated a maximum power density of 365 mW/cm2 and 213 mW/cm 2 with the use of hydrogen/oxygen and hydrogen/pure air, respectively. The performance of the AMFC was also found to be influenced by exposure to carbon dioxide in the air. Hence, the CCMs were pre-treated in potassium hydroxide solution and pure oxygen was used to condition the fuel cell to maximize the power output from the AMFCs. Although satisfactory performance was demonstrated in the AMFC, its stability during cell operation remains a major issue. The poor stability was attributed to degradation of

  7. Chapter 5. Uranium extraction technology from mine and drainage waters of uranium industry wastes. 5.5. Uranium extraction from mine and technical waters by anion exchanger A M(p)

    International Nuclear Information System (INIS)

    Present article is devoted to uranium extraction from mine and technical waters by anion exchanger A M(p). The basic process flow diagram of uranium extraction from mine waters (sorbent anion exchanger A M(p)) was proposed.

  8. Human kidney anion exchanger 1 interacts with kinesin family member 3B (KIF3B)

    Energy Technology Data Exchange (ETDEWEB)

    Duangtum, Natapol [Medical Molecular Biology Unit, Office for Research and Development Faculty of Medicine Siriraj Hospital, Mahidol University, Bangkok 10700 (Thailand); Department of Anatomy, Faculty of Medicine Siriraj Hospital, Mahidol University, Bangkok 10700 (Thailand); Junking, Mutita; Sawasdee, Nunghathai [Medical Molecular Biology Unit, Office for Research and Development Faculty of Medicine Siriraj Hospital, Mahidol University, Bangkok 10700 (Thailand); Cheunsuchon, Boonyarit [Department of Pathology, Faculty of Medicine Siriraj Hospital, Mahidol University, Bangkok 10700 (Thailand); Limjindaporn, Thawornchai, E-mail: limjindaporn@yahoo.com [Department of Anatomy, Faculty of Medicine Siriraj Hospital, Mahidol University, Bangkok 10700 (Thailand); Yenchitsomanus, Pa-thai, E-mail: grpye@mahidol.ac.th [Medical Molecular Biology Unit, Office for Research and Development Faculty of Medicine Siriraj Hospital, Mahidol University, Bangkok 10700 (Thailand)

    2011-09-16

    Highlights: {yields} Impaired trafficking of kAE1 causes distal renal tubular acidosis (dRTA). {yields} The interaction between kAE1 and kinesin family member 3B (KIF3B) is reported. {yields} The co-localization between kAE and KIF3B was detected in human kidney tissues. {yields} A marked reduction of kAE1 on the cell membrane was observed when KIF3B was knockdown. {yields} KFI3B plays an important role in trafficking of kAE1 to the plasma membrane. -- Abstract: Impaired trafficking of human kidney anion exchanger 1 (kAE1) to the basolateral membrane of {alpha}-intercalated cells of the kidney collecting duct leads to the defect of the Cl{sup -}/HCO{sub 3}{sup -} exchange and the failure of proton (H{sup +}) secretion at the apical membrane of these cells, causing distal renal tubular acidosis (dRTA). In the sorting process, kAE1 interacts with AP-1 mu1A, a subunit of AP-1A adaptor complex. However, it is not known whether kAE1 interacts with motor proteins in its trafficking process to the plasma membrane or not. We report here that kAE1 interacts with kinesin family member 3B (KIF3B) in kidney cells and a dileucine motif at the carboxyl terminus of kAE1 contributes to this interaction. We have also demonstrated that kAE1 co-localizes with KIF3B in human kidney tissues and the suppression of endogenous KIF3B in HEK293T cells by small interfering RNA (siRNA) decreases membrane localization of kAE1 but increases its intracellular accumulation. All results suggest that KIF3B is involved in the trafficking of kAE1 to the plasma membrane of human kidney {alpha}-intercalated cells.

  9. Human kidney anion exchanger 1 interacts with kinesin family member 3B (KIF3B)

    International Nuclear Information System (INIS)

    Highlights: → Impaired trafficking of kAE1 causes distal renal tubular acidosis (dRTA). → The interaction between kAE1 and kinesin family member 3B (KIF3B) is reported. → The co-localization between kAE and KIF3B was detected in human kidney tissues. → A marked reduction of kAE1 on the cell membrane was observed when KIF3B was knockdown. → KFI3B plays an important role in trafficking of kAE1 to the plasma membrane. -- Abstract: Impaired trafficking of human kidney anion exchanger 1 (kAE1) to the basolateral membrane of α-intercalated cells of the kidney collecting duct leads to the defect of the Cl-/HCO3- exchange and the failure of proton (H+) secretion at the apical membrane of these cells, causing distal renal tubular acidosis (dRTA). In the sorting process, kAE1 interacts with AP-1 mu1A, a subunit of AP-1A adaptor complex. However, it is not known whether kAE1 interacts with motor proteins in its trafficking process to the plasma membrane or not. We report here that kAE1 interacts with kinesin family member 3B (KIF3B) in kidney cells and a dileucine motif at the carboxyl terminus of kAE1 contributes to this interaction. We have also demonstrated that kAE1 co-localizes with KIF3B in human kidney tissues and the suppression of endogenous KIF3B in HEK293T cells by small interfering RNA (siRNA) decreases membrane localization of kAE1 but increases its intracellular accumulation. All results suggest that KIF3B is involved in the trafficking of kAE1 to the plasma membrane of human kidney α-intercalated cells.

  10. High throughput determination of cleaning solutions to prevent the fouling of an anion exchange resin.

    Science.gov (United States)

    Elich, Thomas; Iskra, Timothy; Daniels, William; Morrison, Christopher J

    2016-06-01

    Effective cleaning of chromatography resin is required to prevent fouling and maximize the number of processing cycles which can be achieved. Optimization of resin cleaning procedures, however, can lead to prohibitive material, labor, and time requirements, even when using milliliter scale chromatography columns. In this work, high throughput (HT) techniques were used to evaluate cleaning agents for a monoclonal antibody (mAb) polishing step utilizing Fractogel(®) EMD TMAE HiCap (M) anion exchange (AEX) resin. For this particular mAb feed stream, the AEX resin could not be fully restored with traditional NaCl and NaOH cleaning solutions, resulting in a loss of impurity capacity with resin cycling. Miniaturized microliter scale chromatography columns and an automated liquid handling system (LHS) were employed to evaluate various experimental cleaning conditions. Cleaning agents were monitored for their ability to maintain resin impurity capacity over multiple processing cycles by analyzing the flowthrough material for turbidity and high molecular weight (HMW) content. HT experiments indicated that a 167 mM acetic acid strip solution followed by a 0.5 M NaOH, 2 M NaCl sanitization provided approximately 90% cleaning improvement over solutions containing solely NaCl and/or NaOH. Results from the microliter scale HT experiments were confirmed in subsequent evaluations at the milliliter scale. These results identify cleaning agents which may restore resin performance for applications involving fouling species in ion exchange systems. In addition, this work demonstrates the use of miniaturized columns operated with an automated LHS for HT evaluation of chromatographic cleaning procedures, effectively decreasing material requirements while simultaneously increasing throughput. Biotechnol. Bioeng. 2016;113: 1251-1259. © 2015 Wiley Periodicals, Inc. PMID:26552005

  11. Adsorption Properties of Ni(II by D301R Anion Exchange Resin

    Directory of Open Access Journals (Sweden)

    Song Xiuling

    2014-01-01

    Full Text Available The adsorption of Ni(II with D301R resin was investigated in this paper. The results showed that the saturated extent of adsorption Ni(II by the resin was 84.3 mg/g. The equilibrium data of Ni(II sorption was better described by Langmuir isotherm model (r2=0.994 while that of Ni(II sorption also fitted in Freundlich isotherm model within the experimental concentration range. The amount of the constant (q0 of Ni(II under 298 K in Langmuir model was 76.92 mg/g, which was close to the experimental results. The constant n was within 2–10 in Freundlich model; it was shown that adsorption of Ni(II by the resin was easy to take place. The uptake kinetics followed the Lagergren pseudo-first-order rate equation (r2=0.9813. The particle diffusion controlled the adsorption process of Ni(II. The coefficient of the intraparticle diffusion increased with the increase of the pH values and the concentration of Ni(II in aqueous solution. There was a drop of 20.1 cm−1 for the bending vibration frequency of N–H bond. Results showed that the adsorption of Ni(II by D301R anion exchange resin was the surface complexation through the infrared spectrum analysis.

  12. Polyphenylene sulfide based anion exchange fiber: Synthesis, characterization and adsorption of Cr(Ⅵ)

    Institute of Scientific and Technical Information of China (English)

    Jiajia Huang; Xin Zhang; Lingling Bai; Siguo Yuan

    2012-01-01

    A fibrous strong base anion exchanger(QAPPS)was prepared for the first time via chloromethylation and quaternary amination reaction of polyphenylene sulfide fiber(PPS),and its physical-chemical structure and adsorption behavior for Cr(Ⅵ)were characterized by FTIR,Energy Dispersive Spectrometry,TG-DTG,elemental analysis and batch adsorptive technique,respectively.The novel fibrous adsorbent could effectively adsorb Cr(Ⅵ)over the pH range 1-12,the maximum adsorption capacity was 166.39 mg/g at pH 3.5,and the adsorption behavior could be described well by Langrnuir isotherm equation model.The adsorption kinetics was studied using pseudo first-order and pseudo second-order models,and the t1/2 and equilibrium adsorption time were 5 and 20 rain respectively when initial Cr(Ⅵ)concentration was 100 mg/L.The saturated fibers could be regenerated rapidly by a mixed solution of 0.5 mol/L NaOH and 0.5 mol/L NaCl,and the adsorption capacity was well maintained after six adsorption-desorption cycles.

  13. Poly(phenyl sulfone) anion exchange membranes with pyridinium groups for vanadium redox flow battery applications

    Science.gov (United States)

    Zhang, Bengui; Zhang, Enlei; Wang, Guosheng; Yu, Ping; Zhao, Qiuxia; Yao, Fangbo

    2015-05-01

    To develop high performance and cost-effective membranes with low permeability of vanadium ions for vanadium redox flow battery (VRFB) application, poly(phenyl sulfone) anion exchange membranes with pyridinium groups (PyPPSU) are prepared and first investigated for VRFB application. PyPPSU membranes show much lower vanadium ions permeability (0.07 × 10-7-0.15 × 10-7 cm2 min-1) than that of Nafion 117 membrane (31.3 × 10-7 cm2 min-1). As a result, the self-discharge duration of the VRFB cell with PyPPSU membrane (418 h) is about four times longer than that of VRFB cell with Nafion 117 membrane (110 h). Furthermore, the VRFB cell with PyPPSU membrane exhibits higher battery efficiency (coulombic efficiency of 97.8% and energy efficiency of 80.2%) compare with that of VRFB cell with Nafion 117 membrane (coulombic efficiency of 96.1% and energy efficiency of 77.2%) at a high current density of 100 mA cm-2. In addition, PyPPSU membrane exhibits stable performance in 100-cycle test. The results indicate that PyPPSU membrane is high performance and low-cost alternative membrane for VRFB application.

  14. A new method for antimony speciation in plant biomass and nutrient media using anion exchange cartridge.

    Science.gov (United States)

    Tisarum, Rujira; Ren, Jing-Hua; Dong, Xiaoling; Chen, Hao; Lessl, Jason T; Ma, Lena Q

    2015-11-01

    A selective separation method based on anion exchange cartridge was developed to determine antimony (Sb) speciation in biological matrices by graphite furnace atomic absorption spectrophotometry (GFAAS). The selectivity of the cartridge towards antimonite [Sb(III)] and antimonate [Sb(V)] reversed in the presence of deionized (DI) water and 2mM citric acid. While Sb(V) was retained by the cartridge in DI water, Sb(III) was retained in citric acid media. At pH 6, Sb(III) and Sb(V) formed Sb(III)- and Sb(V)-citrate complexes, but the cartridge had higher affinity towards the Sb(III)-citrate complex. Separation of Sb(III) was tested at various concentrations in fresh and spent growth media and plant tissues. Our results showed that cartridge-based Sb speciation was successful in plant tissues, which was confirmed by HPLC-ICP-MS. The cartridge retained Sb(III) and showed 92-104% Sb(V) recovery from arsenic hyperaccumulator Pteris vittata roots treated with Sb(III) and Sb(V). The cartridge procedure is an effective alternative for Sb speciation, offering low cost, reproducible results, and simple Sb analysis using GFAAS. PMID:26452943

  15. Enhanced performance of anion exchange membranes via crosslinking of ion cluster regions for fuel cells

    Science.gov (United States)

    Lai, Ao Nan; Guo, Dong; Lin, Chen Xiao; Zhang, Qiu Gen; Zhu, Ai Mei; Ye, Mei Ling; Liu, Qing Lin

    2016-09-01

    Development of anion exchange membranes (AEMs) with high hydroxide conductivity, good dimensional and alkaline stabilities is still a challenge for the practical application of AEM fuel cells. In this study, we report a new strategy to prepare high-performance AEMs with crosslinked ionic regions. A series of phenolphthalein-containing poly(arylene ether sulfone)s crosslinked AEMs was synthesized by grafting ion groups selectively and densely on the phenolphthalein units to form ion clusters that are further crosslinked to generate the hydrophilic ionic regions. The crosslinking reaction not only improved the dimensional stability of the AEMs, but also increased the aggregation of the ion clusters leading to the formation of hydrophilic/hydrophobic phase-separated morphology and ion-conducting channels. As a result, enhancements in both ion conductivity and dimensional stability can be achieved. The crosslinked AEMs showed high hydroxide conductivities in the range of 52.2-143.4 mS cm-1 from 30 to 80 °C and a superb ratio of relative conductivity to relative swelling at 80 °C. Furthermore, the crosslinked AEMs also exhibited good mechanical properties, thermal and alkaline stabilities and desirable single cell performance. This work presents a promising strategy for the synthesis of high-performance AEMs for fuel cells.

  16. Separation of Fluoride Ions in an Electrolytic Cell by Using an AnionExchange Membrane

    International Nuclear Information System (INIS)

    Separation of fluoride ions in an electrolytic cell with an anionexchange membrane which is so-called an electrodialysis process has beenperformed. The experiment have been taken place in room temperature in anelectrolytic cell made by plexiglas consisted on anode and cathode chambersseparated by an anion exchange membrane in dimension of 4 x 4 cm. The carbonand stainless steel are applied as an anode and platinum as s' cathode. Theanolyte is a HNO3 0.3 M solution, while a solution of NaF 0.3 M, and amixture of NaF 0.3 M containing uranyl nitrate solution for separating offluoride ions and uranium are used as a catholyte. The distance between theelectrode and the membrane is 1.5 cm and this distance is kept constant. Theparameters observed are the current voltage, cathode applied, and uraniumconcentration. For the solution without uranium, the results show that thefluoride ions transferred are around 50 % using carbon as a cathode for 3hours and the voltage of 10 volts, while for SS as a cathode are around 93 %.For the solution containing uranium, the fluoride ions transferred are around78 % for 3.5 hours and the uranium ions remain in the catholyte in which mostof them are as 8 yellow deposit of Na2U2O7 on the cathode surface andothers are as a white precipitate of NaUF5 on the bottom of the cathodechamber. (author)

  17. Quantitative compositional analysis of heparin using exhaustive heparinase digestion and strong anion exchange chromatography

    Directory of Open Access Journals (Sweden)

    Pierre Mourier

    2015-03-01

    Full Text Available Heparin is a linear sulfated polysaccharide widely used therapeutically as an anticoagulant. It is also the starting material for manufacturing low-molecular-weight heparins (LMWH. Quality control of heparin and LMWH is critical to ensure the safety and therapeutic activity of the final product. However due to their complex and heterogeneous structure, orthogonal analytical techniques are needed to characterize the building blocks of heparin. One of the state-of-the-art methods for heparin analysis is based on complete enzymatic digestion using a mixture of heparinases I, II, and III, followed by the separation of the resulting oligosaccharides by liquid chromatography. The European Pharmacopoeia strong anion-exchange chromatographic method, used to quantify 1,6-anhydro derivatives in enoxaparin, is here applied to the analysis of the heparin building blocks. Their quantification, namely the determination of their average w/w percentage in the heparin chain, is obtained after identification of all components including glycoserine derivatives and 3-O sulfated di- and tetrasaccharides. This work therefore provides a comprehensive overview of the building blocks of unfractionated heparin, including those chemically modified by the manufacturing process, either within the polysaccharide chain or at its reducing end.

  18. Fundamental study of practical separation of boron isotopes by means of anion exchange resin, (1)

    International Nuclear Information System (INIS)

    Separation of boron isotopes was carried out using a weak base anion exchange column (in free base form). After boric acid solution was passed through the column, the boric acid band formed on the column was eluted with pure water. The authors discuss the effects on boron isotope separation caused by variations of the concentration of feed solution charged to the column, of the amount of boric acid charged and of the flow rate of feed and eluent solutions. Results were as follows: (1) As the concentration of boric acid charged to the column increased and the amount of boric acid charged became large, the amount of enriched 10B(D sup(γ)) increased. (2) The optimum flow rate was 10 -- 20 ml/cm2.hr. (3) The atomic fraction of 10B in the plateau region of the isotope enrichment curve was nearly 0.190, compared with 0.198 for the feed solution. (4) In cases where the boric acid concentration in the effluent never exceeded 0.3 mol/l, no significant tailling was observed at the end of the chromatographic band. (auth.)

  19. Fundamental study of practical separation of boron isotopes by means of anion exchange resin, (2)

    International Nuclear Information System (INIS)

    As we reported earlier, a boric acid band formed in a column of weak base anion exchange resin Diaion WA21 can be eluted with pure water, resulting in good isotope fractionation. In the present research, we carried out various experiments using this process in order to find the necessary conditions for producing a displacement chromatogram at the end of the boric acid band, where 10B is enriched. Suitable conditions were found to be as follows: the concentration of boric acid was 0.1 mol/l, the operating temperature was 400C and the flow rate was 20 ml/hr.cm2. Under these conditions, four experimental runs having different migration lengths (1, 2, 4, 8 m) were carried out by a new method which we named ''Isotopic Plateau Holding Displacement Chromatography''. In these experiments, the enriched part of band was always preceded by the isotopic plateau part, in which the atomic fraction of 10B was maintained at its original value. The results of these experiments carried out by this method showed that the concentration of 10B at the end of the chromatogram increased with the migration length, and in the case of 8 m migration, 10B was enriched from an original value of 19.84 to 33.26%. The separation factor S was found to be constant, 1.0097+-0.0002, irrespective of migration length. (auth.)

  20. Concentration and separation of vanadium from alkaline media by strong alkaline anion-exchange resin 717

    Institute of Scientific and Technical Information of China (English)

    HUANG Jinwen; SU Peng; WU Wenwei; LIAO Sen; QIN Huiquan; WU Xuehang; HE Xiaohu; TAO Liujia; FAN Yanjin

    2010-01-01

    With strong alkaline anion-exchange resin 717 as the sorbent and NaOH solution as the eluent, a study on the sorption from alkaline solution and elution of vanadium(Ⅴ), silicon(Ⅳ), and aluminium(Ⅲ) was carried out. Different parameters affecting the sorption and elution process,including temperature, pH values as well as the ratio of resin to solution, were investigated. The results show that sorption degree of vanadium(Ⅴ) increases with a decrease of pH values, and V(Ⅴ) ions are easier sorbed than Si(Ⅳ) and Al(Ⅲ) ions under the same conditions. The sorption degree of V(Ⅴ), Si(Ⅳ), and Al(Ⅲ) at pH 9.14 for 15 min are 90.6%, 33.5%, and 21.6%, respectively. Si(Ⅳ), Al(Ⅲ), and V(Ⅴ) ions sorbed on 717 resin were eluted by use of 2 mol.L-1 NaOH solution; the desorption degree of V(Ⅴ), Si(Ⅳ), and Al(Ⅲ) for 5 min are 81.7 %,99.1%, and 99.3%, respectively.

  1. Fixation and separation of the elements thorium and uranium using anion exchange resins in nitrate solution

    International Nuclear Information System (INIS)

    The exchange of thorium and uranium between a strong base anion resin and a mixed water + ethanol solvent containing nitrate ions is studied. It is assumed that in the resin the thorium and uranium are fixed in the form of the complexes Th(NO3)62- and UO2(NO3)42- in solution these elements are present in the form of complexes having the general formula: Th(NO3)6-nn-2 and UO2(NO3)4-nn-2 It has been possible to deduce a law for the changes in the partition functions of thorium and uranium as a function of the concentrations of the various species in solution and of the complexing ion NO3. From this has been deduced the optimum operational conditions for separating a mixture of these two elements. Finally, in these conditions, the influence of a few interfering ions has been studied: Ba, Bi, Ce, La, Mo, Pb, Zr. The method proposed can be used either as a preparation, or for the dosage of thorium by a quantitative separation. (author)

  2. PLUTONIUM LOADING CAPACITY OF REILLEX HPQ ANION EXCHANGE COLUMN - AFS-2 PLUTONIUM FLOWSHEET FOR MOX

    Energy Technology Data Exchange (ETDEWEB)

    Kyser, E.; King, W.; O' Rourke, P.

    2012-07-26

    Radioactive plutonium (Pu) anion exchange column experiments using scaled HB-Line designs were performed to investigate the dependence of column loading performance on the feed composition in the H-Canyon dissolution process for plutonium oxide (PuO{sub 2}) product shipped to the Mixed Oxide (MOX) Fuel Fabrication Facility (MFFF). These loading experiments show that a representative feed solution containing {approx}5 g Pu/L can be loaded onto Reillex{trademark} HPQ resin from solutions containing 8 M total nitrate and 0.1 M KF provided that the F is complexed with Al to an [Al]/[F] molar ratio range of 1.5-2.0. Lower concentrations of total nitrate and [Al]/[F] molar ratios may still have acceptable performance but were not tested in this study. Loading and washing Pu losses should be relatively low (<1%) for resin loading of up to 60 g Pu/L. Loading above 60 g Pu/L resin is possible, but Pu wash losses will increase such that 10-20% of the additional Pu fed may not be retained by the resin as the resin loading approaches 80 g Pu/L resin.

  3. Separation of rare earth elements using Ln-EDTA eluent in an anion exchanger

    International Nuclear Information System (INIS)

    Chloride form anion exchange resin was used to separate one of the elements from the rare earth mixture using respectable Ln-EDTA eluent. Sm3+, La3+ or Ce4+ complexed with EDTA was passed through the resin column and eluted with an Sm-EDTA solution as an eluent. Here all the rare earth element ions except Sm3+ were passed. Adsorbed Sm3+ in resin was eluted with 1.0 M HCl solution. If La-EDTA solution as an eluent was used to separate lanthanum ions, lanthanum ions were eluted together with other rare earth elements. When Ce-EDTA solution was also used for separation of Ce4+, it was eluted in the region of other rare earth elements. In the case of Sm-EDTA elution, the elution mechanism was as follows: Absorption: RCl + Ln-Y- ↔ RLnY + Cl-, Sm-EDTA elution: RLnY + Sm-Y- ↔ RSmY + Ln-Y-, HCl elution: RSmY + HCl ↔ RCl + Sm-Y-. (author)

  4. Influence of Hydration Level on Polymer and Water Dynamics in Alkaline Anion Exchange Fuel Cell Membranes

    Science.gov (United States)

    Tarver, Jacob; Kim, Jenny; Tyagi, Madhu; Soles, Christopher; Tsai, Tsung-Han; Coughlin, Bryan

    2015-03-01

    Triblock copolymers based on poly(chloromethylstyrene)-b-poly(ethylene)-b-poly(chloromethylstyrene) can be quaternized to different extents to yield anion exchange membranes for alkaline fuel cells. In the absence of moisture, these membranes demonstrate bilayer lamellar morphology. Upon high levels of hydration, however, in-situ small angle neutron scattering reveals the emergence of higher-order diffraction peaks. This phenomena has previously been observed in analogous diblock copolymer-based membranes and has been attributed to the induction of a multilayer lamellar morphology in which selective striping of water occurs in the center of the ion-rich domain. By conducting humidity-resolved quasielastic neutron scattering (QENS) measurements using deuterated water, we are able to isolate differences in the pico- to nanosecond timescale dynamics of the hydrogenated membrane upon hydration. QENS measurements in the presence of a hydrogenated water source subsequently permit deconvolution and isolation of the translational and rotational dynamics of water as a function of relative humidity, revealing spatial and temporal changes in polymer and water motion at high levels of hydration.

  5. The k{sub 0}-INAA method for the determination of the anion-exchange capacity of propylpyridium silicas

    Energy Technology Data Exchange (ETDEWEB)

    Auler, Lucia M.L.A.; Menezes, Maria Angela de B.C.; Amaral, Angela Maria [Centro de Desenvolvimento de Tecnologia Nuclear (CDTN), Belo Horizonte, MG (Brazil)]. E-mail: aulerlm@cdtn.br; Silva, Cesar R.; Collins, Kenneth E.; Collins, Carol [Universidade Estadual de Campinas, SP (Brazil). Inst. de Quimica. Lab. de Cromatografia Liquida (LABCROM)]. E-mail: chc@iqm.unicamp.br

    2005-07-01

    The present work describes the k{sub 0}-INAA method as an alternative for determination of the ion-exchange capacity of a propyl pyridinium modified silica, which has been recently employed as stationary phase for anion -exchange chromatography. The exchange capacity of the modified silicas was investigated by determining its exchangeable chloride content with k{sub 0}-Instrumental Neutron Activation Analyses. Irradiation experiments were performed in the reactor TRIGA Mark I IPR-R1 located at CDTN/CNEN (Nuclear Technology Development Center / Nuclear Energy National Commission). The results showed that the exchangeable chloride concentration was successfully determined by this analytical method instead of the conventional potentiometric determination with silver nitrate titrimetry. (author)

  6. Selective Anion Exchange Resins for the Removal of Perchlorate [(CIO{sub 4}{sup -})] from Groundwater

    Energy Technology Data Exchange (ETDEWEB)

    Gu, B.

    1999-05-20

    The primary objective of this project was to evaluate a novel bifunctional anion exchange resin for the cost-effective, in situ treatment of groundwater contaminated with perchlorate (ClO{sub 4}{sup -}). Both laboratory and field studies were performed to determine the selectivity and capacity of the bifunctional synthetic resins to sorb ClO{sub 4}{sup -} from simulated or actual contaminated groundwater. A number of synthetic bifunctional resins, including two commercial versions made by Purolite International and three commercially available, mono-functional resins, were tested. Initial laboratory batch and column breakthrough studies determined the best synthetic resins and the optimal conditions for the field experiment. Laboratory results indicated that the bifunctional synthetic resins, D-3696 and RO-02-119 were highly selective toward ClO{sub 4}{sup -} and performed {approx}5 times better than the best commercial nitrate resin (Purolite{reg_sign} A-520E) and more than an order of magnitude better than some nonselective commercial resins (e.g. Amberlite{reg_sign} IRA-900). The bifunctional resins were particularly effective in removing trace quantities of ClO{sub 4}{sup -} in groundwater to below the detection limit ({approx} 3 {micro}g/L). A field trial demonstrated that the bifunctional resin (D-3696) was able to treat {approx} 110,000 bed volumes of groundwater before a 10% breakthrough of ClO{sub 4}{sup -} occurred under the column flow-through conditions (running at {approx} 2 bed volumes per minute). On the other hand, the Purolite{reg_sign} A-520E resin was able to treat {approx} 23,000 bed volumes of groundwater under the same experimental conditions. No pretreatment was needed to remove either dissolved organic matter or other competing anions (such as SO{sub 4}{sup 2-} or NO{sub 3}{sup -}) in the groundwater, and the treatment process did not alter the water quality by removing or adding secondary by-products because of the high selectivity of the

  7. Conservation of order, disorder, and "crystallinity" during anion-exchange reactions among layered double hydroxides (LDHs) of Zn with Al.

    Science.gov (United States)

    Radha, A V; Kamath, P Vishnu; Shivakumara, C

    2007-04-01

    Carbonate and chloride ions mediate an ordered stacking of metal hydroxide slabs to yield ordered layered double hydroxides (LDHs) of Zn with Al, by virtue of their ability to occupy crystallographically well-defined interlayer sites. Other anions such as ClO(4)- (T(d)), BrO(3)- (C(3v)), and NO(3)- (coordination symmetry C(2v)) whose symmetry does not match the symmetry of the interlayer sites (D(3h) or O(h)) introduce a significant number of stacking faults, leading to turbostratic disorder. SO(4)(2-) ions (coordination symmetry C(3v)) alter the long-range stacking of the metal hydroxide slabs to nucleate a different polytype. The degree of disorder is also affected by the method of synthesis. Anion-exchange reactions yield a solid with a greater degree of order if the incoming ion is a CO3(2-) or Cl-. Incoming NO(3)- ions yield an interstratified phase, whereas incoming SO(4)(2-) ions generate turbostratic disorder. Conservation or its converse, elimination, of stacking disorders during anion exchange is the net result of several competing factors such as (i) the orientation of the hydroxyl groups in the interlayer region, (ii) the symmetry of the interlayer sites, (iii) the symmetry of the incoming ion, and (iv) the configuration of the anion. These short-range interactions ultimately affect the long-range stacking order or "crystallinity" of the LDH. PMID:17388484

  8. THERMODYNAMIC STUDY ON ADSORPTION OF AROMATIC SULFONIC ACIDS ONTO MACROPOROUS WEAK BASE ANION EXCHANGER FROM AQUEOUS SOLUTIONS

    Institute of Scientific and Technical Information of China (English)

    Chao Long; Quan-xing Zhang; Ai-min Li; Jin-long Chen

    2004-01-01

    The adsorption equilibrium isotherms of three aromatic sulfonic acid compounds, 2-naphthalenesulfonic acid, ptoluenesulfonic acid and p-chlorobenzenesulfonic acid, from aqueous solutions by macroporous weak base anion exchanger within the temperature range of 293 K-313 K were obtained. Several isotherm equations were correlated with the equilibrium data, and the experimental data was found to fit the three-parameter Redlich-Peterson equation best within the entire range of concentrations. The study showed that the hydrophobicity of solute has distinct influence on adsorption capacity of the anion exchanger for the aromatic sulfonic acid. Moreover, estimations of the isosteric enthalpy, free energy,and entropy change of adsorption were also reported. The positive isosteric enthalpy and entropy change for adsorption indicate an endothermic and entropy driven process in the present study.

  9. An Anion-Exchange Method for the Separation of P-32 Activity in Neutron-Irradiated Biological Material

    International Nuclear Information System (INIS)

    Strong hydrochloric-acid solutions containing small amounts of orthophosphoric and citric acid and radioactive tracers of the elements Na, P, K, Ca, Se, Cr, Mn, Ni, Rb, Sr, Cs, Ba, La, and Ce were titrated with a water suspension of strongly basic anion-exchange resin in the hydroxide form. The titration was carried out to pH = 3.0. It was followed by filtration of the mixture on the top of a small anion-exchange column in the chloride form and a final washing with water. Phosphorus was quantitatively adsorbed by the resin and the scandium retention was better than 96 per cent. The remaining elements passed quantitatively into the effluent, with the exception of nickel, which was adsorbed to a very small extent

  10. An investigation of the sorption/desorption of organics from natural waters by solid adsorbents and anion exchangers

    International Nuclear Information System (INIS)

    The results of laboratory and operational tests at thermal and nuclear power stations on anion exchangers and solid adsorbents of makeup water treatment plants with regard to the sorption/desorption of organic substances in natural water and condensate are presented. The resins Amberlite trademark IRA-67, IRA-900, IRA-958Cl, Purolite registered 2 A-500P, DowexTM3 Marathon, and others were tested. Retention of up to 60-80% of the ''organic'' material on the anion exchangers and organic absorbers installed at different places in the technological scheme of the water processing unit was attained. The possibility of a partial ''poisoning'' of the resins and the degradation of the working characteristics over the first year of operation are discussed. (orig.)

  11. Wheat gluten amino acid analysis by high-performance anion-exchange chromatography with integrated pulsed amperometric detection.

    Science.gov (United States)

    Rombouts, Ine; Lagrain, Bert; Lamberts, Lieve; Celus, Inge; Brijs, Kristof; Delcour, Jan A

    2012-01-01

    This chapter describes an accurate and user-friendly method for determining amino acid composition of wheat gluten proteins and their gliadin and glutenin fractions. The method consists of hydrolysis of the peptide bonds in 6.0 M hydrochloric acid solution at 110°C for 24 h, followed by evaporation of the acid and separation of the free amino acids by high-performance anion-exchange chromatography with integrated pulsed amperometric detection. In contrast to conventional methods, the analysis requires neither pre- or postcolumn derivatization, nor a time-consuming oxidation or derivatization step prior to hydrolysis. Correction factors account for incomplete release of Val and Ile even after hydrolysis for 24 h, and for losses of Ser during evaporation. Gradient conditions including an extra eluent allow multiple sequential sample analyses without risk of Glu accumulation on the anion-exchange column which otherwise would result from high Gln levels in gluten proteins. PMID:22125156

  12. Anion- or Cation-Exchange Membranes for NaBH4/H2O2 Fuel Cells?

    Science.gov (United States)

    Sljukić, Biljana; Morais, Ana L; Santos, Diogo M F; Sequeira, César A C

    2012-01-01

    Direct borohydride fuel cells (DBFC), which operate on sodium borohydride (NaBH4) as the fuel, and hydrogen peroxide (H2O2) as the oxidant, are receiving increasing attention. This is due to their promising use as power sources for space and underwater applications, where air is not available and gas storage poses obvious problems. One key factor to improve the performance of DBFCs concerns the type of separator used. Both anion- and cation-exchange membranes may be considered as potential separators for DBFC. In the present paper, the effect of the membrane type on the performance of laboratory NaBH4/H2O2 fuel cells using Pt electrodes is studied at room temperature. Two commercial ion-exchange membranes from Membranes International Inc., an anion-exchange membrane (AMI-7001S) and a cation-exchange membrane (CMI-7000S), are tested as ionic separators for the DBFC. The membranes are compared directly by the observation and analysis of the corresponding DBFC's performance. Cell polarization, power density, stability, and durability tests are used in the membranes' evaluation. Energy densities and specific capacities are estimated. Most tests conducted, clearly indicate a superior performance of the cation-exchange membranes over the anion-exchange membrane. The two membranes are also compared with several other previously tested commercial membranes. For long term cell operation, these membranes seem to outperform the stability of the benchmark Nafion membranes but further studies are still required to improve their instantaneous power load. PMID:24958292

  13. Optimizing the performance of a membrane bio-electrochemical reactor using an anion exchange membrane for wastewater treatment

    OpenAIRE

    Jian LI; He, Zhen

    2015-01-01

    A membrane bioelectrochemical reactor (MBER) is a system integrating ultrafiltration membranes into microbial fuel cells (MFCs) for energy-efficient wastewater treatment. To improve nitrogen removal, an MBER based on an anion exchange membrane (AEM), the MBER-A, was investigated for treating synthetic solution or actual wastewater during a 200-day operation. The MBER-A significantly improved the removal of total nitrogen to 56.9% with the synthetic solution, compared with 7.6% achieved in the...

  14. Synthesis of blue-photoluminescent graphene quantum dots/polystyrenic anion-exchange resin for Fe(III) detection

    Science.gov (United States)

    Zhang, Wenjun; Gan, Jie

    2016-05-01

    A novel solid fluorescent sensor with millimeter size, based on graphene quantum dots/polystyrenic anion-exchange resin (GQDs/PS-AER) was obtained for the detection of Fe3+. The linear response range of Fe3+ was obtained from 1 μM to 7 μM and the detection limit was as low as 0.65 μM. In addition, the sensor could be regenerated by adding complexing agent EDTA and be separated by using simple filtration.

  15. Nondestructive radio isotopic technique for performance evaluation of industrial grade anion exchange resins Amberlite IRN78 and Indion NSSR

    International Nuclear Information System (INIS)

    The present study deals with the application of radiotracers 131I and 82Br as a non-destructive tool to evaluate the performance of Amberlite IRN78 (nuclear grade) and Indion NSSR (non-nuclear grade) anion exchange resins. In general based on radiotracer applications it was observed that Amberlite IRN78 resins show superior performance over Indion NSSR resins under identical operational parameters.

  16. Sulfuric Acid and Ammonia Generation by Bipolar Membranes Electrodialysis: Transport Rate Model for Ion and Water through Anion Exchange Membrane

    OpenAIRE

    Zhang, Xiaoyan; Lu, Wenhua; Ren, HongYan; Cong, Wei

    2008-01-01

    Regeneration of sulfuric acid and ammonia from ammonium sulfate by bipolar membrane electrodialysis (BMED) coupling with stripping ammonia by air-blowing was studied. The result showed that it was feasible to regenerate sulfuric acid and ammonia from ammonium sulfate solution using this method. Empirical models to describe the ion and water transport behaviors through anion exchange membrane for BMED system were successfully developed. The models were valid to evaluate water transport rate an...

  17. Nondestructive radio isotopic technique for performance evaluation of industrial grade anion exchange resins Amberlite IRN78 and Indion NSSR

    Energy Technology Data Exchange (ETDEWEB)

    Singare, Pravin U. [Bhavan' s College, Mumbai (India). Dept. of Chemistry

    2016-01-15

    The present study deals with the application of radiotracers 131I and 82Br as a non-destructive tool to evaluate the performance of Amberlite IRN78 (nuclear grade) and Indion NSSR (non-nuclear grade) anion exchange resins. In general based on radiotracer applications it was observed that Amberlite IRN78 resins show superior performance over Indion NSSR resins under identical operational parameters.

  18. Separation of iron-55 from manganese cyclotron target material on a 2% cross-linked anion exchanger in hydrochloric acid

    International Nuclear Information System (INIS)

    A simple method is presented for the separation of iron-55 from manganese cyclotron targets. Anion exchange chromatography with 9.0 M hydrochloric acid on a 2% cross-linked resin provides separation not only from large amounts of manganese but also from copper and zinc impurities. Separations are sharp and quantitative and less than 1 μg of manganese remains with the iron-55 when 2 g have been present originally. (author)

  19. Anion-exchange high-performance liquid chromatography with conductivity detection for the analysis of phytic acid in food

    OpenAIRE

    Talamond, Pascale; Doulbeau, Sylvie; Rochette, Isabelle; Guyot, Jean-Pierre; Trèche, Serge

    1999-01-01

    A sensitive method for the accurate determination of phytic acid in food samples is described. The proposed procedure involves the anion-exchange liquid chromatography with conductivity detection. Initially, two methods of determination of phytic acid were compared : absorptiometry and high-performance ion chromatography (HPIC) with chemically suppressed conductivity detector. Unlike most conventional methods involving precipitation by FeCl3, the simpler and more reliable HPIC assay avoids th...

  20. Comparing and Optimizing Nitrate Adsorption from Aqueous Solution Using Fe/Pt Bimetallic Nanoparticles and Anion Exchange Resins

    OpenAIRE

    Muhammad Daud; Zahiruddin Khan; Aisha Ashgar; M. Ihsan Danish; Ishtiaq A. Qazi

    2015-01-01

    This research work was carried out for the removal of nitrate from raw water for a drinking water supply. Nitrate is a widespread ground water contaminant. Methodology employed in this study included adsorption on metal based nanoparticles and ion exchange using anionic resins. Fe/Pt bimetallic nanoparticles were prepared in the laboratory, by the reduction of their respective salts using sodium borohydride. Scanning electron microscope, X-ray diffraction, energy dispersive spectrometry, and ...

  1. Recovery of platinum, tin and indium from spent catalysts in chloride medium using strong basic anion exchange resins

    International Nuclear Information System (INIS)

    Highlights: → Platinum, tin and indium recoveries from spent reforming catalysts. → Adsorption of metal chlorocomplexes on strongly basic anion-exchange resins. → Sequential desorption via elution with reducing (Pt, Sn) or complexing (In) agents. → The elements were recovered in very high yields. → The anion-exchange resins can be reused. - Abstract: This work describes a route for platinum recovery from spent commercial Pt and PtSnIn/Al2O3 catalysts using strong basic mesoporous and macroporous anion exchange resins (Cl- form). The catalysts were leached with aqua regia (75 oC, 20-25 min). Platinum adsorption was influenced by the presence of other metals which form chlorocomplexes (tin, indium) and also base metals (aluminum). However, it was possible to overcome this fact by a sequential desorption procedure. Aluminum was selectively removed from the resins by elution with 3 mol L-1 HCl. Platinum was desorbed passing 1 mol L-1 Na2S2O3 (pH 9). Tin was removed by elution with 0.1 mol L-1 ascorbic acid. Indium was removed using 0.1 mol L-1 EDTA as eluent. Desorption efficiency exceeded 99% for all metals. Metals were recovered in high yields (>98 wt%).

  2. THE EFFECT OF IONIC STRENGTH ON THE UPTAKE OF TAURINE ON A STRONG-BASIC ANION EXCHANGE RESIN

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Studied the effect of ionic strength on the uptake of taurine on a strong-basic anionexchange resin. The batch phase equilibrium experiments of ta urine on the anion exchange resin D290 were conducted at different ionic strength, and then the amounts of uptake of taurine on the resin at different pH were determined. The ion exchange mechanisms of taurine on the anion exchange resin at different pH were discussed. Experimental results showed that with increase of the ionic strength of solution, the adsorbed amount of taurine on the resin D290 decreased; Adding small amounts of NaOH or HCl into the system of taurine aqueous solution/D290 anionresin would make the amount of taurine taken up on the resin to decrease due to the competition uptakes of hydroxyl ion with taurine or the decrease in the amount of absorbable zwitterions of taurine in the solution and excluding the cations of taurine from the anion resin.

  3. Deletion of the anion exchanger Slc26a4 (pendrin) decreases apical Cl−/HCO3− exchanger activity and impairs bicarbonate secretion in kidney collecting duct

    OpenAIRE

    Amlal, Hassane; Petrovic, Snezana; Xu, Jie; Wang, Zhaohui; Sun, Xuming; Barone, Sharon; Soleimani, Manoocher

    2010-01-01

    The anion exchanger Pendrin, which is encoded by SLC26A4 (human)/Slc26a4 (mouse) gene, is localized on the apical membrane of non-acid-secreting intercalated (IC) cells in the kidney cortical collecting duct (CCD). To examine its role in the mediation of bicarbonate secretion in vivo and the apical Cl−/HCO3− exchanger in the kidney CCD, mice with genetic deletion of pendrin were generated. The mutant mice show the complete absence of pendrin expression in their kidneys as assessed by Northern...

  4. Quaternized dimethylaminoethyl methacrylate strong base anion exchange fibers for As(V) adsorption

    International Nuclear Information System (INIS)

    N,N-Dimethylaminoethyl methacrylate (DMAEMA) grafted polyethylene/polypropylene (PE/PP) nonwoven fibers (DMAEMA-g-PE/PP) was prepared by radiation-induced graft polymerization. DMAEMA graft chains on nonwoven fibers were quaternized with dimethyl sulfate solution for the preparation of strong base anion exchange fibers (QDMAEMA-g-PE/PP). Fiber structures were characterized by FTIR, XPS and SEM techniques. The effect of solution pH, contact time, initial As(V) ion concentration and coexisting ions on the As(V) adsorption capacity of the QDMAEMA-g-PE/PP fibers were investigated by performing batch adsorption experiments. The adsorption of As(V) by QDMAEMA-g-PE/PP fibers was found to be independent on solution pH in the range 4.00–10.00. Kinetic experiments show that the As(V) adsorption rate was rapid and As(V) adsorption follows pseudo second-order kinetic model. As(V) adsorption equilibrium data were analyzed using Langmuir and Freundlich adsorption isotherm model equations. Langmuir and Freundlich adsorption isotherm models fitted the experimental data well. The maximum adsorption capacity (qmax) calculated from Langmuir isotherm was found to be 83.33 mg As(V)/g polymer at pH 7.00. The adsorbent was used for three cycles without significant loss of adsorption capacity. The adsorbed As(V) ions were desorbed effectively by a 0.1 M NaOH solution. - Highlights: • QDMAEMA-g-PE/PP fibers have high adsorption capacity for As(V) ions. • Adsorption of As(V) is independent on the solution pH over a wide range (4−10). • As(V) adsorption rate of QDMAEMA-g-PE/PP fibers is considerably fast. • The maximum adsorption capacity (qmax) was found to be 83.33 mg As(V)/g polymer

  5. HB-LINE ANION EXCHANGE PURIFICATION OF AFS-2 PLUTONIUM FOR MOX

    Energy Technology Data Exchange (ETDEWEB)

    Kyser, E. A.; King, W. D.

    2012-07-31

    Non-radioactive cerium (Ce) and radioactive plutonium (Pu) anion exchange column experiments using scaled HB-Line designs were performed to investigate the feasibility of using either gadolinium nitrate (Gd) or boric acid (B as H{sub 3}BO{sub 3}) as a neutron poison in the H-Canyon dissolution process. Expected typical concentrations of probable impurities were tested and the removal of these impurities by a decontamination wash was measured. Impurity concentrations are compared to two specifications - designated as Column A or Column B (most restrictive) - proposed for plutonium oxide (PuO{sub 2}) product shipped to the Mixed Oxide (MOX) Fuel Fabrication Facility (MFFF). Use of Gd as a neutron poison requires a larger volume of wash for the proposed Column A specification. Since boron (B) has a higher proposed specification and is more easily removed by washing, it appears to be the better candidate for use in the H-Canyon dissolution process. Some difficulty was observed in achieving the Column A specification due to the limited effectiveness that the wash step has in removing the residual B after ~4 BV's wash. However a combination of the experimental 10 BV's wash results and a calculated DF from the oxalate precipitation process yields an overall DF sufficient to meet the Column A specification. For those impurities (other than B) not removed by 10 BV's of wash, the impurity is either not expected to be present in the feedstock or process, or recommendations have been provided for improvement in the analytical detection/method or validation of calculated results. In summary, boron is recommended as the appropriate neutron poison for H-Canyon dissolution and impurities are expected to meet the Column A specification limits for oxide production in HB-Line.

  6. HB-LINE ANION EXCHANGE PURIFICATION OF AFS-2 PLUTONIUM FOR MOX

    Energy Technology Data Exchange (ETDEWEB)

    Kyser, E.; King, W.

    2012-04-25

    Non-radioactive cerium (Ce) and radioactive plutonium (Pu) anion exchange column experiments using scaled HB-Line designs were performed to investigate the feasibility of using either gadolinium nitrate (Gd) or boric acid (B as H{sub 3}BO{sub 3}) as a neutron poison in the H-Canyon dissolution process. Expected typical concentrations of probable impurities were tested and the removal of these impurities by a decontamination wash was measured. Impurity concentrations are compared to two specifications - designated as Column A or Column B (most restrictive) - proposed for plutonium oxide (PuO{sub 2}) product shipped to the Mixed Oxide (MOX) Fuel Fabrication Facility (MFFF). Use of Gd as a neutron poison requires a larger volume of wash for the proposed Column A specification. Since boron (B) has a higher proposed specification and is more easily removed by washing, it appears to be the better candidate for use in the H-Canyon dissolution process. Some difficulty was observed in achieving the Column A specification due to the limited effectiveness that the wash step has in removing the residual B after {approx}4 BV's wash. However a combination of the experimental 10 BV's wash results and a calculated DF from the oxalate precipitation process yields an overall DF sufficient to meet the Column A specification. For those impurities (other than B) not removed by 10 BV's of wash, the impurity is either not expected to be present in the feedstock or process, or recommendations have been provided for improvement in the analytical detection/method or validation of calculated results. In summary, boron is recommended as the appropriate neutron poison for H-Canyon dissolution and impurities are expected to meet the Column A specification limits for oxide production in HB-Line.

  7. Chemical separation of Mo and W from terrestrial and extraterrestrial samples via anion exchange chromatography.

    Science.gov (United States)

    Nagai, Yuichiro; Yokoyama, Tetsuya

    2014-05-20

    A new two-stage chemical separation method was established using an anion exchange resin, Eichrom 1 × 8, to separate Mo and W from four natural rock samples. First, the distribution coefficients of nine elements (Ti, Fe, Zn, Zr, Nb, Mo, Hf, Ta, and W) under various chemical conditions were determined using HCl, HNO3, and HF. On the basis of the obtained distribution coefficients, a new technique for the two-stage chemical separation of Mo and W, along with the group separation of Ti-Zr-Hf, was developed as follows: 0.4 M HCl-0.5 M HF (major elements), 9 M HCl-0.05 M HF (Ti-Zr-Hf), 9 M HCl-1 M HF (W), and 6 M HNO3-3 M HF (Mo). After the chemical procedure, Nb remaining in the W fraction was separated using 9 M HCl-3 M HF. On the other hand, Nb and Zn remaining in the Mo fraction were removed using 2 M HF and 6 M HCl-0.1 M HF. The performance of this technique was evaluated by separating these elements from two terrestrial and two extraterrestrial samples. The recovery yields for Mo, W, Zr, and Hf were nearly 100% for all of the examined samples. The total contents of the Zr, Hf, W, and Mo in the blanks used for the chemical separation procedure were 582, 9, 29, and 396 pg, respectively. Therefore, our new separation technique can be widely used in various fields of geochemistry, cosmochemistry, and environmental sciences and particularly for multi-isotope analysis of these elements from a single sample with significant internal isotope heterogeneities. PMID:24801276

  8. Radiotracer application for characterization of nuclear grade anion exchange resins Tulsion A-23 and Dowex SBR LC

    Energy Technology Data Exchange (ETDEWEB)

    Singare, P.U. [Bhavan' s College, Mumbai (India). Dept. of Chemistry

    2015-12-15

    Radio isotopic tracer technique as one of the versatile nondestructive technique is employed to evaluate the performance of nuclear grade anion exchange resins Tulsion A-23 and Dowex SBR LC. The evaluation was made on the basis of ion-isotopic exchange reaction kinetics by using {sup 131}I and {sup 82}Br radioactive tracer isotopes. It was observed that for both the resins, the values of specific reaction rate (min{sup -1}), amount of ion exchanged (mmol) and initial rate of ion exchange (mmol/min) were calculated to be lower for bromide ion-isotopic exchange reaction than that for iodide ion-isotopic exchange reaction. It was observed that for iodide ion-isotopic exchange reaction under identical experimental conditions of 30.0 C, 1.000 g of ion exchange resins and 0.001 mol/L labeled iodide ion solution, the values of specific reaction rate (min{sup -1}), amount of iodide ion exchanged (mmol), initial rate of iodide ion exchange (mmol/min) and log K{sub d} were calculated as 0.377, 0.212, 0.080 and 15.5 respectively for Dowex SBR LC resin, which was higher than 0.215, 0.144, 0.031 and 14.1 respectively as that obtained for Tulsion A23 resins. Also at a constant temperature of 30.0 C, as the concentration of labeled iodide ion solution increases from 0.001 mol/L to 0.004 mol/L, the percentage of iodide ions exchanged increases from 84.75 % to 90.20 % for Dowex SBR LC resins which was higher than increases from 57.66 % to 62.38 % obtained for Tulsion A23 resins. The identical trend was observed for the two resins during bromide ion-isotopic exchange reaction. The overall results indicate superior performance of Dowex SBR LC over Tulsion A23 resins under identical experimental conditions.

  9. Radiotracer application for characterization of nuclear grade anion exchange resins Tulsion A-23 and Dowex SBR LC

    International Nuclear Information System (INIS)

    Radio isotopic tracer technique as one of the versatile nondestructive technique is employed to evaluate the performance of nuclear grade anion exchange resins Tulsion A-23 and Dowex SBR LC. The evaluation was made on the basis of ion-isotopic exchange reaction kinetics by using 131I and 82Br radioactive tracer isotopes. It was observed that for both the resins, the values of specific reaction rate (min-1), amount of ion exchanged (mmol) and initial rate of ion exchange (mmol/min) were calculated to be lower for bromide ion-isotopic exchange reaction than that for iodide ion-isotopic exchange reaction. It was observed that for iodide ion-isotopic exchange reaction under identical experimental conditions of 30.0 C, 1.000 g of ion exchange resins and 0.001 mol/L labeled iodide ion solution, the values of specific reaction rate (min-1), amount of iodide ion exchanged (mmol), initial rate of iodide ion exchange (mmol/min) and log Kd were calculated as 0.377, 0.212, 0.080 and 15.5 respectively for Dowex SBR LC resin, which was higher than 0.215, 0.144, 0.031 and 14.1 respectively as that obtained for Tulsion A23 resins. Also at a constant temperature of 30.0 C, as the concentration of labeled iodide ion solution increases from 0.001 mol/L to 0.004 mol/L, the percentage of iodide ions exchanged increases from 84.75 % to 90.20 % for Dowex SBR LC resins which was higher than increases from 57.66 % to 62.38 % obtained for Tulsion A23 resins. The identical trend was observed for the two resins during bromide ion-isotopic exchange reaction. The overall results indicate superior performance of Dowex SBR LC over Tulsion A23 resins under identical experimental conditions.

  10. Effect of alcohols on separation behavior of rare earth elements using benzimidazole-type anion-exchange resin in nitric acid solutions

    International Nuclear Information System (INIS)

    Chromatographic separation experiments of trivalent rare earth elements were performed using benzimidazole type anion-exchange resin in nitric/alcohol mixed solvent systems at room temperature. As a result, it was found those trivalent rare earth elements are able to be separated mutually in a 20% HNO3 and 80% MeOH mixed solvent. Based on these results, we systematically examined using various alcohols to make clear the role of alcohols in anion-exchange reactions at various temperatures. (author)

  11. Understanding ion and solvent transport in anion exchange membranes under humidified conditions

    Science.gov (United States)

    Sarode, Himanshu

    Anion exchange membranes (AEM) have been studied for more than a decade for potential applications in low temperature fuel cells and other electrochemical devices. They offer the advantage of faster reaction kinetics under alkaline conditions and ability to perform without costly platinum catalyst. Inherently slow diffusion of hydroxide ions compared to protons is a primary reason for synthesizing and studying the ion transport properties in AEMs. The aim of this thesis is to understand ion transport in novel AEMs using Pulse Gradient stimulated Spin Echo Nuclear Magnetic Resonance technique (PGSE NMR), water uptake, ionic conductivity, Small Angle X-ray Scattering (SAXS) etc. All experiments were performed under humidified conditions (80--95% relative humidity) and fuel cell operating temperatures of 30--90°C. In this work, the NMR tube design was modified for humidifying the entire NMR tube evenly from our previous design. We have developed a new protocol for replacing caustic hydroxide with harmless fluoride or bicarbonate ions for 19F and 13 C NMR diffusion experiments. After performing these NMR experiments, we have obtained in-depth understanding of the morphology linked ion transport in AEMs. We have obtained the highest fluoride self-diffusion coefficient of > 1 x 10-5 cm2/sec ( 55°C) for ETFE-g-PVBTMA membrane which is a result of low tortuosity of 1 obtained for the membrane. This faster fluoride transport combined with low tortuosity of the membrane resulted in > 100mS/cm hydroxide conductivity for the membrane. Polycyclooctene (PCOE) based triblock copolymers are also studied for in-depth understanding of molecular weight, IEC, mechanical and transport properties. Effect of melting temperature of PCOE has favorable effect on increasing ion conductivity and lowering activation energy. Mechanical properties of these types of membranes were studied showing detrimental effect of water plasticization which results in unsuitable mechanical properties

  12. Anion exchange removal of Al3+ from Li+-Al3+ aqueous solution (originating from lithium recovery from brine

    Directory of Open Access Journals (Sweden)

    Anissa Somrani

    2014-06-01

    Full Text Available The purpose of this study is to separate aluminum(III ion from an aqueous solution containing Li+ at 25°C. Al3+ was transferred into [Al(C2O43]3- by means of complexation and removed by an anion exchange resin. This resin was anionic type Amberlite IRA 402 regenerated by sodium chloride. Hence, a theoretical study based on speciation diagrams was carried out to determine the best pH domain for separation. The complexation of aluminum ions by ammonium oxalate was studied. The motar ratio of Ox/Al and pH was investigated. Optimum values of these factors were found to be 3 and 4 respectively. In this case, the remaining lithium is 98.5%.

  13. Behavior of cationic, anionic and colloidal species of titanium, zirconium and thorium in presence of ion exchange resins

    International Nuclear Information System (INIS)

    The distribution of titanium, zirconium and thorium is aqueous and resin phases has been studied using strong cationic resin in the R-NH4 form. Solutions of the above elements in perchloric, nitric, hydrochloric and suphuric media were used. Each set of experiments was made by separately varying one of the five parameters - type of anion present, acidity of solution, temperature of percolation, age of solution and concentration of the element. It was found that, depending on the particular balance of these parameters, the elements investigated may be found in acidic solutions either as cationic, anionic or colloidal species. It is emphasized that the colloidal species of titanium, zirconium or thorium are not retained by the ion exchangers, and from this property a method for the separation and purification of the above elements has been outlined

  14. Purification of drinking water from radioactive contamination by final consumers by means of combined cation and anion exchangers

    International Nuclear Information System (INIS)

    It should be tried to develop an apparatus which makes it possible for the final consumer to purify the drinking water himself in the case of a radioactive contamination of the water. After thorough preliminary studies the most suitable kinds of exchange resins and the best arrangement for a combined cation and anion exchange resins and the best arrangement for a combined cation and anion exchange equipment were determined in inactive preliminary tests. Subsequent the useful capacity (NK) and the purifying factor (RF) were determined for the fission products 90Sr, 131I and 137Cs. The results were for 90Sr: NK = 30 1/2 x 0.5 l resin, RF >= 4.102, for 131I: NK = 32 1/2 x 0.5 l resin, RF = 3.7.102 and for 137Cs: NK > 35 1/2 x 0.5 l resin, RF >= 103. With 2 x 1 l resin the concentration of possible fission products in water can be reduced by 2 orders of magnitude ore more. A proposal for the construction of a household decontamination equipment for drinking water is made. The cost of production will be about A.S. 400,-- to 600,--. (author)

  15. Recovery of nitric acid from simulated acidic high level radioactive waste using pore-filled anion exchange membranes

    International Nuclear Information System (INIS)

    Acidic waste is generated at different stages of nuclear fuel cycle. The waste contains minor amounts of actinides (241Am, Pu, Np) along with large number of long-lived radionuclides such as 137Cs, 90Sr, 106Ru etc. Before disposal or storage, the overall activity of the waste needs to be reduced. Along with this, the high amount of acid present in the waste needs to be removed. In this study, DD has been used to recover nitric acid from acidic solutions with compositions similar to radioactive waste using pore-filled anion exchange membranes

  16. Evidence for F-/SiO- anion exchange in the framework of As-synthesized all-silica zeolites

    KAUST Repository

    Liu, Xiaolong

    2011-05-12

    Not everything changes: Charge-compensating anions can be exchanged in as-synthesized zeolite frameworks with changes in both the density of defect sites and of the hydrophobic character of the zeolite. The reversible transformation occurs without dissolution/recrystallization of the zeolite and preserves the size and shape of the crystals (see picture). Fluoride removal is not possible in all-silica D4R units, for which fluoride ions play a structure-directing role. © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  17. Refolding with Simultaneous Purification of Recombinant Human Granulocyte Colony-stimulating Factor from Escherichia coli Using Strong Anion Exchange Chromatography

    Institute of Scientific and Technical Information of China (English)

    Chao Zhan WANG; Jiang Feng LIU; Xin Du GENG

    2005-01-01

    The urea denatured recombinant human granulocyte colony-stimulating factor (rhGCSF) which was expressed in Escheriachia coli (E. coli) was refolded with simultaneous purification by strong anion exchange chromatography (SAX) in the presence of low concentration of urea. The effect of urea concentration on this refolding process was investigated. The obtained refolded rhG-CSF has a high specific activity of 2.3×108 U/mg, demonstrating that the proteins were completely refolded during the chromatographic process. With only one step by SAX in 40 min, purity and mass recovery of the refolded and purified rhG-CSF were 97% and43%, respectively.

  18. Dynamic separation of Szilard-Chalmers reaction products applied to the trioxalatochromium ion adsorbed on anionic exchange resin

    International Nuclear Information System (INIS)

    A method of dynamic elution of recoiled 51Cr+3, formed by the Szilard-Chalmers reaction during the irradiation of trioxalatochromium ion adsorbed on anionic exchange resin is presented. The influence of some factors on the separation yield of chromium-51, such as: composition, concentration and flow rate of eluent, mesh size of the resin and irradiation time are studied. The results are compardd with those obtained by the static method, in which the recoiled atom is separated from the target after irradiation. Because of the high separation yield of chromium-51, the method of dynamic separation is proposed for routine production of this elemnt, with high specific activities. (author)

  19. Ion-Isotopic Exchange Reaction Kinetics using Anion Exchange Resins Dowex 550A LC and Indion-930A

    Directory of Open Access Journals (Sweden)

    P.U. Singare

    2014-06-01

    Full Text Available The present paper deals with the characterization of ion exchange resins Dowex 550A LC and Indion-930A based on kinetics of ion-isotopic exchange reactions for which the short lived radioactive isotopes 131I and 82Br were used as a tracers. The study was performed for different concentration of ionic solution varying from 0.001 mol/L to 0.004 mol/L and temperature in the range of 30.0 °C to 45.0 °C. The results indicate that as compared to bromide ion-isotopic exchange reaction, iodide exchange reaction take place at the faster rate. For both the ion-isotopic exchange reactions, under identical experimental conditions, the values of specific reaction rate increases with increase in the ionic concentration and decreases with rise in temperature. It was observed that at 35.00C, 1.000 g of ion exchange resins and 0.002 mol/L labeled iodide ion solution for iodide ion-isotopic exchange reaction, the values of specific reaction rate (min-1, amount of ion exchanged (mmol, initial rate of ion exchange (mmol/min and log Kd were 0.270, 0.342, 0.092 and 11.8 respectively for Dowex 550A LC resin, which was higher than the respective values of 0.156, 0.241, 0.038 and 7.4 as that obtained for Indion-930A resins. From the results, it appears that Dowex 550A LC resins show superior performance over Indion-930A resins under identical experimental conditions.

  20. Preparation and testing of poly(4-vinylpyridine-DVB) based anion exchangers with enhanced selectivity for 99TcO4- ions present in radioactive effluents

    International Nuclear Information System (INIS)

    Three strong-base anion exchange resins were prepared by quaternization of poly(4-vinylpyridine-DVB) with different alkyl (-CH3, -C2H5, and -n-C4H9) halides. The base polymer in granular form was also synthesized in the laboratory. All three anion exchangers, base polymer and a conventional strong-base anion exchanger were characterized for moisture content, ion exchange capacity and batch uptake of 99TcO4- ions from acidic, neutral, and alkaline test solutions, each containing 1.0 M competing NO3- ions and 99mTcO4- radiotracer. Amongst the synthesized resins, the resin with bulky n-butyl group on the pyridine nitrogen showed higher affinity for 99TcO4- ions. (author)

  1. Highly efficient platinum group metal free based membrane-electrode assembly for anion exchange membrane water electrolysis.

    Science.gov (United States)

    Pavel, Claudiu C; Cecconi, Franco; Emiliani, Chiara; Santiccioli, Serena; Scaffidi, Adriana; Catanorchi, Stefano; Comotti, Massimiliano

    2014-01-27

    Low-temperature electricity-driven water splitting is an established technology for hydrogen production. However, the two main types, namely proton exchange membrane (PEM) and liquid alkaline electrolysis, have limitations. For instance, PEM electrolysis requires a high amount of costly platinum-group-metal (PGM) catalysts, and liquid alkaline electrolysis is not well suited for intermittent operation. Herein we report a highly efficient alkaline polymer electrolysis design, which uses a membrane-electrode assembly (MEA) based on low-cost transition-metal catalysts and an anion exchange membrane (AEM). This system exhibited similar performance to the one achievable with PGM catalysts. Moreover, it is very suitable for intermittent power operation, durable, and able to efficiently operate at differential pressure up to 3 MPa. This system combines the benefits of PEM and liquid alkaline technologies allowing the scalable production of low-cost hydrogen from renewable sources. PMID:24339230

  2. The influence of plutonium concentration and solution flow rate on the effective capacity of macroporous anion exchange resin

    International Nuclear Information System (INIS)

    The principal aqueous process used to recover and purify plutonium at the Los Alamos Plutonium Facility is anion exchange in nitric acid. Previous studies with gel-type anion exchange resin have shown an inverse relationship between plutonium concentration in the feed solution and the optimum flow rate for this process. Because gel-type resin has been replaced with macroporous resin at Los Alamos, the relationship between plutonium concentration and solution flow rate was reexamined with the selected Lewatit MP-500-FK resin using solutions of plutonium in nitric acid and in nitric acid with high levels of added nitrate salts. Our results with this resin differ significantly from previous data obtained with gel-type resin. Flow-rate variation from 10 to 80 liters per hour had essentially no effect on the measured quantities of plutonium sorbed by the macroporous resin. However, the effect of plutonium concentration in the feed solutions was pronounced, as feed solutions that contained the highest concentrations of plutonium also produced the highest resin loadings. The most notable effect of high concentrations of dissolved nitrate salts in these solutions was an increased resin capacity for plutonium at low flow rates. 16 refs., 7 figs., 2 tabs

  3. Direct determination of seleno-amino acids in biological tissues by anion-exchange separation and electrochemical detection.

    Science.gov (United States)

    Cavalli, S; Cardellicchio, N

    1995-07-01

    Several studies have described the determination of selenium in protein extracts from tissues of marine or terrestrial animals, but have not identified the different chemical forms of selenium that are present. Selenium may be present as seleno-amino acids. Selenocysteine, for example, is a normal component of glutathione peroxidase, an antioxidant enzyme which may behave like other antioxidants, such as vitamin E, protecting tissues against methylmercury toxicity. The present study illustrates a method for the characterization of seleno-amino acids, such as selenocysteine and selenomethionine, in proteins extracted from the liver of marine mammals. The mechanism of detoxification of methylmercury, which involves seleno-compounds, is identified. The analytical determination was carried out using high-performance anion-exchange chromatography coupled with integrated pulsed amperometric detection (HPAEC-IPAD). This method allows the direct determination of underivatized amino acids, eliminating the procedure of pre- or postcolumn derivatization. The chromatographic separation was carried out on an anion-exchange column using a quaternary gradient elution. In order to optimize this method, interferences of amino acids and the influence of pH and ionic strength on the separation and electrochemical detection were studied. The IPAD response for the direct detection of amino acids is optimum at pH > 11. The detection limit (S/N = 3) for selenocysteine was found to be 450 micrograms/l. The application of this method for the identification of seleno-amino acids in protein hydrolysates is also shown. PMID:7640774

  4. Determination of plutonium isotopes in urine samples from radiation workers using 236Pu tracer, anion exchange resin and alpha spectrometry

    International Nuclear Information System (INIS)

    Bioassay technique is used for the estimation of actinides present in the body based on their excretion rate through body fluids. For occupational radiation workers urine assay is the preferred method for monitoring of chronic internal exposure. Determination of low concentrations of actinides such as plutonium, americium and uranium at low level of mBq in urine by alpha spectrometry requires pre-concentration of large volumes of urine. This paper deals with standardization of analytical method for the determination of Pu-isotopes in urine samples using anion exchange resin and 236Pu tracer for radiochemical recovery. The method involves oxidation of urine followed by co-precipitation of plutonium along with calcium phosphate. Separation of Pu was carried out by Amberlite, IRA-400, anion exchange resin. Pu-fraction was electrodeposited and activity estimated using tracer recovery by alpha spectrometer. Twenty routine urine samples of radiation workers were analyzed and consistent radiochemical tracer recovery was obtained in the range 74-96% with a mean and standard deviation of 85 and 6% respectively. (author)

  5. Determination of thorium and uranium in activated concrete by inductively coupled plasma mass spectrometry after anion-exchange separation

    International Nuclear Information System (INIS)

    A sensitive analytical method was established for the determination of Th and U in activated concrete samples. The method combines an anion-exchange separation step with an ICP-MS determination technique. In the ICP-MS measurement, a few μg mL-1 of Al and Ca, a few ng mL-1 of Mn, La, Ce, Nd and Pb and pg mL-1amounts of Li, Zr, Nb and Ba coexisting in the anion-exchange fraction of Th and U did not interfere. No adverse interference effects were observed in real sample analyses. The obtained detection limits (3 σ, n = 10) of Th and U were 2.3 and 1.8 pg mL -1, respectively. The analytical precisions for ca. 5 μg g -1 Th and ca. 1 μg g -1 U in real activated concrete samples were equally less than 7% RSD. The accuracies obtained by the analysis of GSJ rock standard samples were -18.1 to 0.4% for the Th determination and -14.0 to -5.7% for the U determination. The method uses the conventional absolute calibration curve. The internal standard calibration is unnecessary. (orig.)

  6. Production of {sup 61}Cu using natural cobalt target and its separation using ascorbic acid and common anion exchange resin

    Energy Technology Data Exchange (ETDEWEB)

    Das, Sujata Saha; Chattopadhyay, Sankha; Barua, Luna [Radiopharmaceuticals Laboratory, Board of Radiation and Isotope Technology (BRIT), Variable Energy Cyclotron Centre (VECC), Kolkata 700064 (India); Das, Malay Kanti, E-mail: mkdas@vecc.gov.in [Radiopharmaceuticals Laboratory, Board of Radiation and Isotope Technology (BRIT), Variable Energy Cyclotron Centre (VECC), Kolkata 700064 (India)

    2012-02-15

    {sup 61}Cu was produced by {sup nat}Co({alpha}, xn){sup 61}Cu reaction. {sup 61}Cu production yield was 89.5 MBq/{mu}Ah (2.42 mCi/{mu}Ah) at the end of irradiation (EOI). A simple radiochemical separation method using anion exchange resin and ascorbic acid has been employed to separate the product radionuclide from inactive target material and co-produced non-isotopic impurities. The radiochemical separation yield was about 90%. Radiochemical purity of {sup 61}Cu was >99% 1 h after EOI. Final product was suitable for making complex with N{sub 2}S{sub 2} type of ligands. - Highlights: Black-Right-Pointing-Pointer High purity, no-carrier added {sup 61}Cu produced from natural cobalt target. Black-Right-Pointing-Pointer {sup 61}Cu separated from impurities using anion exchange resin and ascorbic acid. Black-Right-Pointing-Pointer {sup 61}Cu preparation was successfully used to label N{sub 2}S{sub 2}-type of ligand.

  7. Recovery of uranium from UCF liquid waste by anion exchange resin CG-400: Breakthrough curves, elution behavior and modeling studies

    International Nuclear Information System (INIS)

    Highlights: ► Amberlite CG-400 anion exchange resin has been used for the recovery of uranium. ► The breakthrough curves and elution behaviors of CG-400 resin have been studied in detailed. ► The mathematical models have been used to analyze the experimental data. ► The CG-400 resin has been applied successfully for uranium recovery from UCF liquid waste. - Abstract: Continuous fixed-bed column studies were carried out by using Amberlite CG-400 anion exchange resin for the recovery of uranium from aqueous solutions (synthetic solutions and uranium conversion facility (UCF) liquid waste). Effects of operating parameters such as flow rate and bed height were studied. The breakthrough capacity decreases with increasing flow rate, but this dependence was not significant with a long column. The maximum breakthrough capacity of uranium ions were achieved by CG-400 resin at a flow rate of 0.2 mL min−1 and bed height 9.1 cm (4 g resin). The elution behavior of uranium from CG-400 resin by various eluents have been investigated and the results show that 0.5 mol L−1 HNO3 is a good eluent for uranium recovery. The Adams–Bohart, Thomas, Yoon–Nelson and Dose–Response models were applied to the experimental data to determine the characteristic parameters of the column for process design using linear regression. The breakthrough curve calculated from the Dose–Response model was in best agreement with the experimental data

  8. Synthesis and characterization of a novel hybrid material as amphoteric ion exchanger for simultaneous removal of cations and anions

    Energy Technology Data Exchange (ETDEWEB)

    Shah, Brijesh, E-mail: brijeshshah27@gmail.com; Chudasama, Uma, E-mail: uvcres@gmail.com

    2014-07-15

    Highlights: • A novel hybrid exchanger ZrD (zirconium diethylene triamine) is synthesized for the first time. • Characterization and structure elucidation reveals that ZrD exhibits amphoteric character. • Amphoteric behaviour of ZrD is established by simultaneous removal of cations and anions. • Cations are exchanged in ZrD through chelation with nitrogen as coordinating sites. • ZrD can be regenerated and reused with not much decline in performance. - Abstract: A new hybrid chelating ion exchanger zirconium diethylene triamine (ZrD) has been synthesized by a simple sol–gel route using inexpensive and easily available chemicals. ZrD has been characterized for elemental analysis (ICP-AES, CHN analysis), TGA, FTIR, X-ray diffraction, SEM and EDX. Physical and ion exchange characteristics as well as chemical stability of the material in various media have been studied. Structural determination reveals that ZrD exhibits amphoteric character. Anion exchange capacity (AEC) for Cl{sup −}, Br{sup −}, Cr{sub 2}O{sub 7}{sup 2−}, F{sup −} and AsO{sub 4}{sup 3−} has been determined. Cations are exchanged through chelation where coordinating sites are offered by nitrogen atoms present in the amine groups of ZrD. Distribution coefficient K{sub d} for Co{sup 2+}, Ni{sup 2+}, Cu{sup 2+}, Zn{sup 2+} (transition metal ions) and Hg{sup 2+}, Cd{sup 2+}, Pb{sup 2+} (heavy metal ions) has been evaluated by batch equilibration techniques in aqueous and various electrolyte media/concentrations. Based on α the separation factor, a few binary separations have been performed on a chromatographic column packed with ZrD. The amphoteric behaviour of ZrD has been demonstrated by simultaneous exchange of Cu{sup 2+} and Cl{sup −} in CuCl{sub 2}. A study on the regeneration and reuse of ZrD indicates that it is effective upto four cycles without much decline in performance.

  9. The degradation of strong basic anion exchange resins and mixed-bed ion-exchange resins: Effect of degradation products on radionuclide speciation

    International Nuclear Information System (INIS)

    The most important water-soluble products of the radiolytic degradation of anion exchange resins in a cementitious environment are ammonia and methylamines. These ligands do not form complexes with most radionuclides. Exceptions are Ni, Ag, and Pd, which form strong complexes with amines. Other degradation products of anion and mixed-bed ion-exchange resins are of no importance concerning the complexation of trivalent radionuclides. This is shown indirectly by adsorption experiments: The degradation products do not have a significant effect on the adsorption of Eu(III) on calcite. The effect of ammonia and methylamines on the complexation of Ni, Ag, and Pd is investigated by chemical modeling. For Ni and Ag, rather reliable predictions can be made using available thermodynamic data. In the case of Pd, large uncertainties are encountered due to unreliable data and gaps in the set of important species. The system Pd(II)-ammonia-water is explored in detail. Predominant species are inferred by chemical analogy, and their thermodynamic data are estimated. The uncertainty in these estimated and measured but unreliable data is bound by qualitative and quantitative chemical reasoning

  10. Studies of removal of palladium(II) ions from chloride solutions on weakly and strongly basic anion exchangers.

    Science.gov (United States)

    Hubicki, Z; Wołowicz, A; Leszczyńska, M

    2008-11-30

    Palladium and its compounds find wide application in industry as a catalytic agent in different manufacture processes. Recovery of precious metals from industrial wastes is difficult and time consuming but in spite of these disadvantages it becomes profitable. Palladium(II) ions sorption from various chloride solutions of the composition: 0.1-6.0M HCl-0.00056 M Pd(II), 1.0M ZnCl(2)-0.1M HCl-0.00056 M Pd(II), 1.0M AlCl(3)-0.1M HCl-0.00056 M Pd(II) on the weakly and strongly basic anion exchangers (Varion ATM, Varion ADM and Varion ADAM) was discussed. The sorption research of Pd(II) ions on these resins was carried out by means of static and dynamic methods. The dynamic processes were applied in order to determine the breakthrough curves of Pd(II) ions. Moreover, the working ion-exchange capacities as well as the weight and bed distribution coefficients were determined from the Pd(II) breakthrough curves. The recovery factors of Pd(II) ions (% R) depending on the phase contact time were obtained by means of static methods. The highest ion-exchange capacities for the 0.1-6.0M HCl-0.00056 M Pd(II) systems were obtained for the weakly basic ion-exchange resin Varion ADAM. PMID:18358602

  11. Properties of solvated electrons, alkali anions and other species in metal solutions and kinetics of cation and electron exchange reactions. Final report

    International Nuclear Information System (INIS)

    The properties of solutions of alkali metals in amine solvents were studied by optical, ETR, NMR and electrochemical methods. Complexation of the alkali cations by crown ethers and cryptands permitted the preparation of concentrated solutions of alkali metals in amine and ether solvents. Extensive alkali metal NMR studies of the exchange of M+ with crown-ethers and cryptands and of the alkali metal anion, M-, were made. The first crystalline salt of an alkali metal anion, Na+ Cryptand [2.2.2]Na- was synthesized and characterized and led to the preparation of other alkali metal anion salts. This research provided the foundation for continuing studies of crystalline alkalide salts

  12. Study on the Retention Behavior of Aromatic Carboxylic and Sulfonic acid on a New Anion Exchange Column

    Institute of Scientific and Technical Information of China (English)

    SHI,Ya-Li; CAI,Ya-Qi; MOU,Shi-Fen

    2008-01-01

    Ion chromatography (IC) has gradually developed into a preferred method for the determination of inorganic anions. And in recent years some low molecular aliphatic acid can be also separated in the ion exchange column with the development of stationary phase. But for the determination of aromatic ionic compounds there are some problems. The aromatic anions show enhanced retention due to interaction with the π electrons of the aromatic backbone. Although the addition of an organic modifier can alleviate the difficulty, it is not the ultimate solution.IonPac AS20 column was developed using a unique polymer bonding technology and its substrate coating is aliphatic backbone. The polymer is completely free of any π electron-containing substituents in the AS20 column. In this paper, the retention behavior of aromatic carboxylic and sulfonic acid on two hydroxide-selective columns,IonPac AS11-HC, AS16, and the new column AS20 was also studied. The result showed that the retentions of ten compounds on three columns were different with each other because of their different column characteristics.Among them 4-chlorobenzene sulfonic acid, 3,5-dihydric benzoic acid and salicylic acid obviously exhibited the weakest retention on the IonPac AS20. It was showed that π-π bond function between anion and stationary phases was weakened in AS20 column because its polymer was completely free of any π electron-containing substituents.So in this paper the AS20 was selected as an analytical column to separate ten aromatic ionic compounds, fumaric acid with conjugate bond included. The retention behavior, separation of the ten compounds and effect of temperature on their retention in the anion-exchange column AS20 (2 mm) were studied. The result showed that those compounds could be separated with each other when running in gradient program and the organic modifier was unnecessary during the separation. So it is showed that AS20 column can be used as a separating column because its

  13. Stable and selective scintillating anion-exchange sensors for quantification of 99TcO4− in natural freshwaters

    International Nuclear Information System (INIS)

    New dual functionality scintillating anion-exchange resins were developed for selective determination of 99TcO4− in various natural freshwater samples. Stable scintillating particles were formed by preparing the vinyl monomer 2-[4-(4′-vinylbiphenylyl)]-5-(4-tert-butylphenyl)-1,3,4-oxadiazole (vPBD), starting with the commercial organic flour TBut-PBD and its subsequent copolymerization with styrene, divinylbenzene, and p-chloromethylstyrene mixture. To integrate the radiochemical separation and radiometric detection steps within the same bead, the chloromethyl groups of the scintillating resins were subjected to amination reactions with dioctylamine (DOA) and trioctylamine (TOA). On-line quantification of 99TcO4− was achieved by packing the scintillating anion-exchange resin into Teflon tubing for quantification by a flow scintillation analyzer (FSA). The two functionalized resins were selective for pertechnetate over the common anions in natural freshwaters, especially Cl− and SO42− with up to 1000 ppm and with up to 10 ppm I− and Cr2O72−. The uptake efficiency of the TOA sensor decreased from 97.88% to 85.08% in well water and river water, respectively, while the counting efficiency was almost constant (69.50%). The DOA performance showed lower efficiency in the two water types relative to TOA. On the other hand, the DOA sensor could be regenerated by 5 M HNO3 for reuse at least four times without losing its chemical or optical performance. The detection limit was 1.45 Bq which could be achieved by loading 45 mL from well and tap water containing the maximum contaminant level (MCL) of 99Tc (33 Bq/L). -- Highlights: • Two novel extractive scintillating sensors for monitoring 99TcO4− were developed. • The resins are selective for pertechnetate over the common anions and chromate ions. • The materials have high chemical and optical stability with good detection efficiency. • 99TcO4− was determined in three freshwaters contain different

  14. Preparation of high-capacity, weak anion-exchange membranes by surface-initiated atom transfer radical polymerization of poly(glycidyl methacrylate) and subsequent derivatization with diethylamine

    Science.gov (United States)

    Qian, Xiaolei; Fan, Hua; Wang, Chaozhan; Wei, Yinmao

    2013-04-01

    Ion-exchange membrane is of importance for the development of membrane chromatography. In this work, a high-capacity anion-exchange membrane was prepared by grafting of glycidyl methacrylate (GMA) onto the surface of regenerated cellulose (RC) membranes via surface-initiated atom transfer radical polymerization (SI-ATRP) and subsequent derivatization with diethylamine. Attenuated total reflectance Fourier-transform infrared (ATR-FTIR), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM) were used to characterize changes in the chemical functionality, surface topography and pore morphology of the modified membranes. The static capacity of the prepared anion-exchange membrane was evaluated with bovine serum albumin (BSA) as a model protein. The results indicated that the anion-exchange membrane which could reach a maximum capacity of 96 mg/mL for static adsorption possesses a higher adsorption capacity, and the adsorption capacity increases with the polymerization time. The effect of pH and salt concentration confirmed that the adsorption of BSA followed ion-exchange mechanism. The established method would have potential application in the preparation of anion-exchange membrane.

  15. Heterometallic modular metal-organic 3D frameworks assembled via new tris-β-diketonate metalloligands: nanoporous materials for anion exchange and scaffolding of selected anionic guests.

    Science.gov (United States)

    Carlucci, Lucia; Ciani, Gianfranco; Maggini, Simona; Proserpio, Davide M; Visconti, Marco

    2010-11-01

    -48% of the cell volume and include the anions and many guest solvent molecules. The guest solvent molecules can be reversibly removed by thermal activation with retention of the framework structure, which proved to be stable up to about 270°C, as confirmed by TGA and powder XRD monitoring. The anions could be easily exchanged in single-crystal to single-crystal processes, thereby allowing the insertion of selected anions into the framework channels. PMID:20938934

  16. Molecular physiology and genetics of Na+-independent SLC4 anion exchangers

    OpenAIRE

    Alper, Seth L.

    2009-01-01

    Plasmalemmal Cl–/HCO3– exchangers are encoded by the SLC4 and SLC26 gene superfamilies, and function to regulate intracellular pH, [Cl–] and cell volume. The Cl–/HCO3– exchangers of polarized epithelial cells also contribute to transepithelial secretion and reabsorption of acid–base equivalents and Cl–. This review focuses on Na+-independent electroneutral Cl–/HCO3– exchangers of the SLC4 family. Human SLC4A1/AE1 mutations cause the familial erythroid disor...

  17. Do TFSA Anions Slither? Pressure Exposes the Role of TFSA Conformational Exchange in Self-Diffusion.

    Science.gov (United States)

    Suarez, Sophia N; Rúa, Armando; Cuffari, David; Pilar, Kartik; Hatcher, Jasmine L; Ramati, Sharon; Wishart, James F

    2015-11-19

    Multinuclear ((1)H, (2)H, and (19)F) magnetic resonance spectroscopy techniques as functions of temperature and pressure were applied to the study of selectively deuterated 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)amide (EMIM TFSA) ionic liquid isotopologues and related ionic liquids. For EMIM TFSA, temperature-dependent (2)H T1 data indicate stronger electric field gradients in the alkyl chain region compared to the imidazolium ring. Most significantly, the pressure dependences of the EMIM and TFSA self-diffusion coefficients revealed that the displacements of the cations and anions are independent, with diffusion of the TFSA anions being slowed much more by increasing pressure than for the EMIM cations, as shown by their respective activation volumes (28.8 ± 2.5 cm(3)/mol for TFSA vs 14.6 ± 1.3 cm(3)/mol for EMIM). Increasing pressure may lower the mobility of the TFSA anion by hindering its interconversion between trans and cis conformers, a process that is coupled to diffusion according to published molecular dynamics simulations. Measured activation volumes (ΔV(‡)) for ion self-diffusion in EMIM bis(fluoromethylsulfonyl)amide and EMIM tetrafluoroborate support this hypothesis. In addition, (2)H T1 data suggest increased ordering with increasing pressure, with two T1 regimes observed for the MD3 and D2 isotopologues between 0.1-100 and 100-250 MPa, respectively. The activation volumes for T1 were 21 and 25 cm(3)/mol (0-100 MPa) and 11 and 12 cm(3)/mol (100-250 MPa) for the MD3 and D2 isotopologues, respectively. PMID:26509865

  18. Ion Mobility Spectrometry-Hydrogen Deuterium Exchange Mass Spectrometry of Anions: Part 1. Peptides to Proteins

    Science.gov (United States)

    Donohoe, Gregory C.; Khakinejad, Mahdiar; Valentine, Stephen J.

    2015-04-01

    Ion mobility spectrometry (IMS) coupled with hydrogen deuterium exchange (HDX)-mass spectrometry (MS) has been used to study the conformations of negatively-charged peptide and protein ions. Results are presented for ion conformers of angiotensin 1, a synthetic peptide (SP), bovine insulin, ubiquitin, and equine cytochrome c. In general, the SP ion conformers demonstrate a greater level of HDX efficiency as a greater proportion of the sites undergo HDX. Additionally, these ions exhibit the fastest rates of exchange. Comparatively, the angiotensin 1 ions exhibit a lower rate of exchange and HDX level presumably because of decreased accessibility of exchange sites by charge sites. The latter are likely confined to the peptide termini. Insulin ions show dramatically reduced HDX levels and exchange rates, which can be attributed to decreased conformational flexibility resulting from the disulfide bonds. For the larger ubiquitin and protein ions, increased HDX is observed for larger ions of higher charge state. For ubiquitin, a conformational transition from compact to more elongated species (from lower to higher charge states) is reflected by an increase in HDX levels. These results can be explained by a combination of interior site protection by compact conformers as well as decreased access by charge sites. The elongated cytochrome c ions provide the largest HDX levels where higher values correlate with charge state. These results are consistent with increased exchange site accessibility by additional charge sites. The data from these enhanced IMS-HDX experiments are described in terms of charge site location, conformer rigidity, and interior site protection.

  19. The Role of Anion Exchanger on Pulmonary Vascular Response to Sustained Alveolar Hypoxia in the Isolated Perfused Rabbit Lung

    Directory of Open Access Journals (Sweden)

    Farzaneh Ketabchi

    2015-05-01

    Full Text Available Background: Some respiratory diseases may induce alveolar hypoxia thereby hypoxic pulmonary vasoconstriction (HPV. However, the mechanisms of this physiologic phenomenon are not fully understood. This study was the first to investigate the role of anion exchanger in sustained HPV. Methods: Experiments were performed in the isolated perfused rabbit lung. After preparation, the lungs were divided into six groups: two DIDS (4,4-diisothiocyanostilbene 2,2-disulfonic acid, anion exchanger inhibitor-treated [200 µM (n=5 or 400 µM (n=3] hypoxic groups, two HCO3- free hypoxic groups, one control hypoxic group (n=7 and one control normoxic group (n=4. DIDS were added to the perfusate at 10 minutes before starting the experiments. In the HCO3- free groups, HEPES (4-(2-Hydroxyethylpiperazine-1-ethanesulfonic acid were added to the perfusate instead of bicarbonate. Furthermore, in the HEPES1 (n=4 and HEPES2 (n=4 groups, the lungs were ventilated with hypoxic gas with or without CO2, respectively. Results: Ventilation of the lungs with hypoxic gas resulted in biphasic HPV, the acute (0-20 minutes and sustained (20-60 minutes phases. No alteration in both phases of HPV was detected by DIDS (200 µM. However, DIDS (400 µM, extended the ascending part of acute HPV until min 24. Both phases of HPV were decreased in the HEPES1 group. However, in the HEPES 2 group, HPV tended to increase during the rising part of the acute phase of HPV. Conclusions: Since DIDS (400 µM extended acute phase of HPV, and HCO3- free perfusate buffer enhanced rising phase of it, therefore it can be suggested that anion exchanger may modulate HPV especially during the acute phase. The abstract of this article was presented as a poster in the congress of European Respiratory Society (ERS on Monday, 08 September 2014, Munich, Germany and was published in the ERJ September 1, 2014 vol. 44 no. Suppl 58 P2343.

  20. Determination of {sup 129}I in environmental samples by AMS and NAA using an anion exchange resin disk

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, Takashi [AMS Management Section, Mutsu Establishment, Japan Atomic Energy Agency, 4-24, Minato-machi, Mutsu, Aomori 035-0064 (Japan)]. E-mail: suzuki.takashi58@jaea.go.jp; Banba, Shigeru [Natural Radioactivity Analysis Group, Japan Chemical Analysis Center, 295-3, Sanno-cho, Inage-ku, Chiba-shi, Chiba 263-0002 (Japan); Kitamura, Toshikatsu [AMS Management Section, Mutsu Establishment, Japan Atomic Energy Agency, 4-24, Minato-machi, Mutsu, Aomori 035-0064 (Japan); Kabuto, Shoji [AMS Management Section, Mutsu Establishment, Japan Atomic Energy Agency, 4-24, Minato-machi, Mutsu, Aomori 035-0064 (Japan); Isogai, Keisuke [Natural Radioactivity Analysis Group, Japan Chemical Analysis Center, 295-3, Sanno-cho, Inage-ku, Chiba-shi, Chiba 263-0002 (Japan); Amano, Hikaru [AMS Management Section, Mutsu Establishment, Japan Atomic Energy Agency, 4-24, Minato-machi, Mutsu, Aomori 035-0064 (Japan)

    2007-06-15

    We have developed a new extraction method for the measurement of {sup 129}I by accelerator mass spectrometry (AMS) utilizing an anion exchange resin disk. In comparison to traditional methods such as solvent extraction and ion exchange, this method provides for simple and quick sample handling. This extraction method was tested on soil, seaweed and milk samples, but because of disk clogging, the milk samples and some of the seaweed could not be applied successfully. Using this new extraction method to prepare samples for AMS analysis produced isotope ratios of iodine in good agreement with neutron activation analysis (NAA). The disk extraction method which take half an hour is faster than previous techniques, such as solvent extraction or ion exchange which take a few hours. The combination of the disk method and the AMS measurement is a powerful tool for the determination of {sup 129}I. Furthermore, these data will be available for the environmental monitoring before and during the operation of a new nuclear fuel reprocessing plant in Japan.

  1. Determination of 129I in environmental samples by AMS and NAA using an anion exchange resin disk

    International Nuclear Information System (INIS)

    We have developed a new extraction method for the measurement of 129I by accelerator mass spectrometry (AMS) utilizing an anion exchange resin disk. In comparison to traditional methods such as solvent extraction and ion exchange, this method provides for simple and quick sample handling. This extraction method was tested on soil, seaweed and milk samples, but because of disk clogging, the milk samples and some of the seaweed could not be applied successfully. Using this new extraction method to prepare samples for AMS analysis produced isotope ratios of iodine in good agreement with neutron activation analysis (NAA). The disk extraction method which take half an hour is faster than previous techniques, such as solvent extraction or ion exchange which take a few hours. The combination of the disk method and the AMS measurement is a powerful tool for the determination of 129I. Furthermore, these data will be available for the environmental monitoring before and during the operation of a new nuclear fuel reprocessing plant in Japan

  2. Liquid–liquid anion exchange extraction studies of samarium(III from salicylate media using high molecular weight amine

    Directory of Open Access Journals (Sweden)

    Aniruddha M. Mandhare

    2015-07-01

    Full Text Available Liquid–liquid extraction and separation of samarium(III were carried out by using 0.025 mol dm−3 2-octylaminopyridine(2-OAP in xylene at 298 K. The extraction behavior of samarium was studied as a function of pH, weak acid concentration, extractant concentration, diluent, and equilibration time. Samarium was quantitatively extracted at pH 7.5 to 10.0 from 0.01 mol dm−3 sodium salicylate solution with 0.025 mol dm−3 2-OAP. The possible composition of the extracted species in organic phase has been determined by using model of slope analysis method and extraction mechanism was found to proceed via an anion exchange mechanism. The stripping efficiency was found to be quantitative in HNO3, HCl and CH3COOH. The robustness of the procedure was demonstrated by the average recoveries obtained (>99.6% for samarium(III extraction in the presence of several cations and anions which are commonly associated with it. The proposed method facilitates the separation and determination of samarium(III from binary and synthetic mixtures. The various thermodynamic functions like free energy (ΔG, enthalpy (ΔH and entropy (ΔS of extraction mechanism were discussed.

  3. A SIM-MOF: three-dimensional organisation of single-ion magnets with anion-exchange capabilities.

    Science.gov (United States)

    Baldoví, José J; Coronado, Eugenio; Gaita-Ariño, Alejandro; Gamer, Christoph; Giménez-Marqués, Mónica; Mínguez Espallargas, Guillermo

    2014-08-18

    The formation of a metal-organic framework (MOF) with nodes that have single-molecule magnet (SMM) behaviour has been achieved by using mononuclear lanthanoid analogues, also known as single-ion magnets (SIMs), which enormously simplifies the challenging issue of making SMM-MOFs. Here we present a rational design of a family of MOFs, [Ln(bipyNO)4](TfO)3⋅x solvent (Ln=Tb (1); Dy (2); Ho (3); Er (4); TfO=triflate), in which the lanthanoid centres have an square-antiprismatic coordination environment suitable for SIM behaviour. Magnetic measurements confirm the existence of slow magnetic relaxation typical of SMMs, which has been rationalised by means of a radial effective charge model. In addition, we have explored the incorporation of bulky polyoxometalates (POMs) into the cavities of the SIM-MOF by anion exchange, finding that they do not interfere with the slow magnetic relaxation. This demonstrates the robustness of the frameworks and opens the possibility of incorporating non-innocent anions. PMID:24804629

  4. Behavior of copper (II )and uranium ( VI) in precipitation chromatography in the system anion exchange resin - hexacyanoferrate (II )

    International Nuclear Information System (INIS)

    In this work it is shown the efficiency of precipitation chromatography for separation and concentration of metallic elements by using a strong anionic-exchange resin saturated with hexacyanoferrate (II). Metallic cations, like Cu (II) and U (VI), are retained from highly diluted solutions and enriched into the resin, in the form of the correspondent insoluble hexacyanoferrate (II), precipitated inside the resin, which permitted the visual observation of a chromatographic zone on the top of the column. It will be discussed the conditions of sorption and elution of the cations uptake by the resin. This system permits the enrichment of the above mentioned cations onto the resin and offers the possibility of interesting separations as well. (author)

  5. Studies on the recovery of plutonium from hydrochloric acid-oxalic acid solutions using anion exchange method

    International Nuclear Information System (INIS)

    The sorption of Pu(IV) from aqueous hydrochloric acid-oxalic acid medium was investigated using different anion exchangers viz., Dowex-1X4, Amberlyst A-26, and Amberlite XE-270 for developing a method for recovery of plutonium from oxalate waste. The distribution ratios for the sorption of Pu(IV) determined as a function of [HClx59', [oxalic acidx59' and [AlCl3x59' revealed that the sorption of Pu(IV) from ≤ 4 M HCl is too low for recovery. The distribution ratio for Pu(IV) increases significantly as the concentration of HCl> 6M. Sorption of Pu(IV) by all the resins decreases drastically in presence of oxalic acid. However, the sorption of Pu(IV) from hydrochloric acid-oxalic acid solutions increases substantially in presence of AlCl3 making the recovery feasible. (author). 2 refs., 2 tabs

  6. Determination of gold in low grade ores and concentratrs by anion exchange separation followed by neutron activation

    International Nuclear Information System (INIS)

    The benefication of tailings fror Kolar Gold Mines involves the flotation of sulphides. Appreciable amounts of arsenic and antimony are expected to accompany gold in this process. The activation analysis of gold in these samples is facilitated by a preseparation of gold from arsenic and antimony. The present paper describes a method for the rapid analysis of gold in the concentration range 0.5 to 50 ppm using a simple pre-irradiation separation, with the recovery of gold being evaluated by an isotope dilution technique using 198Au tracer. The method is based on the absorption of the AuCl4- complex on anion-exchange resin in conjuction with isotope dilution technicque to evaluate the recovery of gold. The resin is then irradiated and counted along with a reference standard similarly prepared. (T.G.)

  7. Analytical applications of a liquid anion-exchanger for the separation of uranium(IV) in malonate solution.

    Science.gov (United States)

    Dalvi, M B; Khopkar, S M

    1978-10-01

    Uranium was quantitatively extracted with 4% Amberlite LA-1 in xylene at pH 2.5-4.0 from 0.001 M malonic acid. It was stripped from the organic phase with 0.01 M sodium hydroxide and determined spectrophotometrically at 530 nm as its complex with 4-(2-pyridylazo) resorcinol. Of various liquid anion-exchangers tested, Amberlite LA-1 was found to be best. Uranium was separated from alkali and alkaline earth metal ions, thallium(I), iron(II), silver, arsenic(III) and tin(IV) by selective extraction, and from zinc, cadmium, nickel, copper(II), cobalt(II), chromium(III), aluminium, iron(III), lead, bismuth, antimony(III) and yttrium by selective stripping. The separation from scandium, zirconium, thorium and vanadium(V) was done by exploiting differences in the stability of chloro-complexes. PMID:18962334

  8. Examination of Amine-Functionalised Anion-Exchange Membranes for Possible Use in the All-Vanadium Redox Flow Battery

    International Nuclear Information System (INIS)

    The applicability of amine-functionalised anion-exchange membranes (AEMs) for use in the all-vanadium redox flow battery has been studied. A selection of radiation-grafted aminated membranes functionalised with dimethylamine, trimethylamine or diazabicyclo(2,2,2)octane were extensively tested. The success of each grafting process was confirmed by Raman and infrared spectroscopies, titrimetry and ionic conductivity measurements. The amine-functionalised membranes were found to have poor thermo-oxidative stability and high vanadium cation permeabilities. The results highlight the importance of balancing ionic conductivity with vanadium cation permeability and indicate that amine-based functional groups may not be suitably stable for the membranes to remain true AEMs when in use in the all-vanadium redox flow battery

  9. Imidazolium-Functionalized Anion Exchange Polymer Electrolytes with High Tensile Strength and Stability for Alkaline Membrane Fuel Cells

    International Nuclear Information System (INIS)

    This study reports novel kinds of high tensile strength alkaline anion-exchange membranes composed of imidazolium-functionalized anion exchange polymer electrolytes. The membranes were prepared by a combined thermal and chemical cross-linking of poly (vinyl alcohol) and poly (3-methyl-1-vinylimidazolium chloride)-co-(1-vinylpyrrolidone) (PMVIC-co-VP). Characterizations by AC impedance technique, mechanical property, FTIR spectroscopy, scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS), along with the water uptake, alkaline resistance and oxidation stability were carried out on the membranes consisting of different PVA/PVA-PMVIC-co-VP mass ratios to evaluate their applicability in alkaline fuel cells. The membrane in a mass ratio of 1:0.4 exhibited high tensile stress at break in the range of 59.3∼76.6 MPa, and the elongation at break around 9.2∼14.9%, depending on the annealing temperature from 130∼190 °C. The OH− conductivity of the membranes was found to be increased with increasing annealing temperature and mass ratio, and reached high up to 1.7 × 10−2 S cm−1. Besides, the membranes showed perfect oxidation stability in 30% H2O2 for 250 hours with no obvious weight loss was observed. XPS analysis indicated that some degradation occurred when the membrane was exposed to 8 M KOH at 85 °C for 312 h, but no lessened OH− conductivity was detected. SEM pictures revealed an ordered microvoid structure with pore size ca. 100∼150 nm uniformly dispersed on the membrane surface, which imparted the PVA/PVA-PMVIC-co-VP membrane with good OH− conductivity

  10. Separation of plutonium on the anion exchanger BIO-RAD 1-X2 and its application to radiochemical analysis

    International Nuclear Information System (INIS)

    The element Pu (Z = 94) is a member of the actinide series of the elements (Z = 89 -103). The actinides have similar chemical properties and are also similar to the lanthanides (Z = 57 -71). Sixteen isotopes of Pu have been synthesized, all of which are radioactive. The Pu present in the environment originates from the atmospheric nuclear tests from 1950 to 1963, which produced the so-called 'global fallout'. As a result, 6.5 · 1015 Bq 239Pu (2.8 tons), 4.4 · 1015 Bq 240Pu (0.52 tons), and 3.7 · 104 Bq 241Pu (0.04 tons) were dispersed over the world. A contribution also to the global fallout was the ignition of the satellite SWAP 9A in the atmosphere in 1964, equipped with a battery powered by 6.3 · 1014 Bq (1 kg) of 238Pu. In addition to these sources, nuclear reactors, reprocessing plants and radioactive waste facilities may contribute with their emissions to increase locally the Pu concentration in their environment. In the PSI laboratory, we are confronted with the determination of traces of 238Pu, 239Pu and 240Pu in environmental and biological materials. Because of the low quantity of Pu in the analyzed samples, which is usually below 100 mBq, it is mandatory to separate the Pu from all other accompanying elements. The separated Pu is then measured by alpha spectrometry. In this work, the anion exchanger BIO-RAD AG 1 is extensively used for the separation of Pu from different matrices. This exchanger is superior when only Pu is determined in the sample. In addition, it is also very suitable when other actinides, such as Am and Cm, are also determined. No preconcentration step is necessary for the Pu separation. The resins introduced by the company Eichrom Industries in the 90's, which allow the separation of the actinides from the major environmental elements and from each other, requires relatively small volumes of sample solution. This report describes the extensive utilization of the classical anion exchanger BIO-RAD 1-X2 in 8 molar nitric acid for the

  11. INTERACTION MECHANISM OF ORGANIC MATTER WITH GEL TYPE POLYSTYRENE STROUGLY BASIC ANION EXCHANGE RESIN AND REGENERATION OF THE ORGANISM FOULED RESIN I.The interreaction mechanism be

    Institute of Scientific and Technical Information of China (English)

    ZhuXingbao; WangZhansen; 等

    1995-01-01

    It was generally considered that contamination of the gel type polystyrene strong basic anion exchange resin by or ganic matter in natural water is the result of ion exchange and Van der waal′s adsorption on it.On the basis of laboratory and industrial experiments,this paper confirmed that the interreaction between organic matter and resin polymer matrix is primarily controled by a Van der waal′s adsorption.

  12. P123-T Oligonucleotide Purification Strategies using a New High-Capacity Anion Exchange Resin

    OpenAIRE

    Deetz, M.; Fisher, J. R.; Gehris, A.; Maikner, J.; Kinzey, M.

    2007-01-01

    With the advent of nucleic acid silencing technologies and the need for high purity diagnostic and therapeutic oligonucleotides, there is a need for high-capacity chromatographic supports that can deliver economic purification processes. A new, 30 micron, mono-sized, polymeric resin has been recently developed that provides high resolution and high capacity for synthetic oligonucleotides. Physical properties of this new resin will be described, including particle size uniformity, ion exchange...

  13. Determination of mycophenolic acid in mest products using mixed mode reversed phase-anion exchange clean-up and liquid chromatography-high-resolution mass spectrometry

    DEFF Research Database (Denmark)

    Sørensen, Louise Marie; Nielsen, Kristian Fog; Jacobsen, Thomas;

    2008-01-01

    A method for determination of mycophenolic acid (MPA) in dry-cured ham, fermented sausage and liver pate is described. MPA was extracted from meat with bicarbonate-acetonitrile, further cleaned-up by mixed mode reversed phase-anion exchange and detected using a LC-MS system with electrospray...

  14. Investigation on the Use of the Weakly Basic Polyacrylate Anion-Exchanger Amberlite IRA-68 for Sorption and Separation of Iminodiacetate Complexes of Rare Earth Elements

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Based on the determined affinity series of rare earth element complexes with IMDA for the anion-exchangers, purification of macroquantities of Nd3+ from Y3+, Sm3+ from Ho3+, La3+ from Nd3+ and La3+ from Pr3+ on the weakly basic gel anion-exchanger Amberlite IRA-68 was studied. Using the presented method on 1 L of Amberlite IRA-68 in the acetate form, it is possible to obtain about 240 g Nd2O3 purified from Y2O3. Great difference in affinity of La3+ and Nd3+ as well as Pr3+ complexes for this anion-exchanger in the acetate form indicates the possibility of applying this process for purification of lanthanum on the increased scale. On 1 L of Amberilte IRA-68 in the acetate form it is possible to obtain about 1125 g La2O3 purified from Nd2O3. On the basis of these results it can be assumed that unique properties of polyacrylate anion-exchangers enable their application for separation of rare earth elements.

  15. Complexation or uranyl ion. II. Complexation of uranyl ion in the VP-IAp anion exchanger phase during sorption from carbonate media

    International Nuclear Information System (INIS)

    The complicated process of increased uranium sorption from carbonate medium by the strongly basic anion exchanger VP-1Ap after additional treatment with alkaline solution was studied by IR spectroscopy. The process is related to the formation of certain complex forms of uranyl, differing in degree of polymerization, in which polynuclear forms predominate

  16. Comparison in the extraction properties of Pu(IV) in piperidinium and pyrrolidinium nitrate anchored anion exchange resins

    Energy Technology Data Exchange (ETDEWEB)

    Selvan, B. Robert; Suneesh, A.S.; Venkatesan, K.A.; Antony, M.P.; Vasudeva Rao, P.R. [Indira Gandhi Centre for Atomic Research, Kalpakkam (India). Fuel Chemistry Div.

    2016-07-01

    Piperidinium nitrate (Pip-NO{sub 3}) and pyrrolidinium nitrate (Pyr-NO{sub 3}) functional groups were anchored on a poly(styrene-divinylbenzene) matrix and evaluated the resultant anion exchange resin for the extraction of plutonium from nitric acid medium. The distribution coefficient (K{sub d}, mL/g) of Pu(IV) in these resins increased with the concentration of nitric acid, reaching a maximum K{sub d} at 7 M nitric acid, followed by decrease. The extraction of Pu(IV) increased with the duration of equilibration followed by the establishment of equilibrium, occurred within four hours of equilibration. The kinetic data were fitted with pseudo-first order and pseudo-second order rate equations. The apparent plutonium exchange capacity was determined to be ∝256 mg/g for Pip-NO{sub 3} resin and 285 mg/g for Pyr-NO{sub 3} resin at 7 M nitric acid. The radiolytic degradation of Pip-NO{sub 3} and Pyr-NO{sub 3} in presence of nitric acid (7 M) was studied upto a dose of 200 KGy and the results are reported in this paper.

  17. Chromium (VI removal from aqueous solutions by purolite base anion-exchange resins with gel structure

    Directory of Open Access Journals (Sweden)

    Balan Catalin

    2013-01-01

    Full Text Available The removal of Cr (VI from aqueous solution using two strong base anionic resins with gel structure, Purolite A-400 (styrene-divinylbenzene matrix and Purolite A-850 (acrylic matrix was investigated in batch technique. The sorption efficiency was determined as a function of phases contact time, solution pH, resin dose, temperature and initial Cr (VI concentration. The percentage of Cr (VI removed reaches maximum values (up to 99 % in the pH range 4 - 5.3 under a resin dose of 6 g/L and of Cr (VI concentration up to 100 mg/L. An increase in temperature has a positive effect on the Cr (VI sorption process. The equilibrium sorption data were fitted with the Freundlich, Langmuir and Dubinin-Radushkevich isotherm models, using both linear and nonlinear regression method. The Langmuir model very well verifies the experimental data and gives the maximum sorption capacity of 120.55 mg Cr (VI/g and 95.82 mg Cr (VI/g for A-400 and A-850 resins, respectively. The thermodynamic study and mean free energy of sorption values calculated using Dubinin-Radushkevich equation indicated the sorption is a chemical endothermic process. The kinetic data were well described by pseudo-second order kinetic equation and the sorption process is controlled by external (film diffusion and intraparticle diffusion.

  18. Determination of plutonium in environmental samples by controlled valence in anion exchange

    DEFF Research Database (Denmark)

    Chen, Q.J.; Aarkrog, A.; Nielsen, S.P.;

    1993-01-01

    The title method was successfully used for collecting Pu-239, Pu-249 from 200 litres of seawater by coprecipitation with 16 g FeSO4 . 7H2O under reducing conditions without filtering. The plutonium is leached by concentrated HNO3 + HCI from the coprecipitate and the solid particles. The precipitate...... is heated at 400-degrees-C and digested in aqua regia. Na2SO3 and NaNO2 have been applied to obtain the Pu4+ valence state in 0.571 N HN03 for different samples. Plutonium and thorium are coadsorbed on anionic resin from 8N HN03. The column is eluted with 8N HN03 containing fresh NaNO2 to keep the Pu4......+ state for uranium decontamination. The system of the column is changed from 8N HNO3 to concentrated HCl with 50 ml concentrated HCI containing a few milligrams of NaNO2. Further decontamination of thorium was achieved by elution with concentrated HCI instead of 9N HCl. The plutonium is successfully...

  19. Characterization of an anionic-exchange membranes for direct methanol alkaline fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Abuin, Graciela C. [Centro de Procesos Superficiales, Instituto Nacional de Tecnologia Industrial (INTI), Av. Gral. Paz 5445, B1650KNA, San Martin, Buenos Aires (Argentina); Nonjola, Patrick; Mathe, Mkhulu K. [Council for Scientific and Industrial Research (CSIR), Material Science and Manufacturing, PO Box 395, Brumeria, Pretoria 0001 (South Africa); Franceschini, Esteban A.; Izraelevitch, Federico H.; Corti, Horacio R. [Departamento de Fisica de la Materia Condensada, Comision Nacional de Energia Atomica (CNEA), Av. Gral. Paz 1499, B1650KNA, San Martin, Buenos Aires (Argentina)

    2010-06-15

    Ammonium quaternized polymers such as poly (arylene ether sulfones) are being developed and studied as candidates of ionomeric materials for application in alkaline fuel cells, due to their low cost and promising electrochemical properties. In this work, a quaternary ammonium polymer was synthesized by chloromethylation of a commercial polysulfone followed by amination process. Quaternized polysulfone membrane properties such us water and water-methanol uptake, electrical conductivity and Young's modulus were evaluated and compared to Nafion 117, commonly employed in direct methanol fuel cells. The anionic polysulfone membrane sorbs more water than Nafion all over the whole range of water activities, but it uptakes much less methanol as compared to Nafion. The specific conductivity of the fully hydrated polysulfone membrane equilibrated with KOH solutions at ambient temperature increases with the KOH concentration, reaching a maximum of 0.083 S cm{sup -1} for 2 M KOH, slightly less conductive than Nafion 117. The elastic modulus of the polysulfone membranes inmersed in water is similar to that reported for Nafion membranes under the same conditions. We concluded that quaternized polysulfone membrane are good candidates as electrolytes in alkaline direct methanol fuel cells. (author)

  20. Determination of plutonium in environmental samples by controlled valence in anion exchange

    International Nuclear Information System (INIS)

    The method was successfully used for collecting 239,240Pu from 200 litres seawater by coprecipitation with 16 g FeSO4.7H2O under reducing conditions without filtering. The plutonium is leached by concentrated HNO3 + HCl from the coprecipitate and the solid particles. The precipitate is heated at 400 deg. C and digested in aqua regia. Na2SO3 and NaNO2 have been applied to obtain Pu+4 valence in 0.5-1 N HNO3 for different samples. Plutonium and thorium are coabsorbed on anionic resin from 8 N HNO3. The column is eluated with 8 N HNO3 containing fresh NaNO2 to keep Pu+4 valence for uranium decontamination. The system of the column is changed from 8 N HNO3 to concentrated HCl with 50 ml conc. HCl containing a few milligram NaNO2. Further decontamination of thorium was achieved by eluation with concentrated HCl instead of 9 N HCl. The plutonium is successfully stripped by H2O, NaOH, 2 N HNO3 and 0.5 N HNO3 containing 0.01 M NaNO3. The chemical yield of plutonium for a 200 litres-seawater sample is 60-80%. The resolution of the electroplated thin source is very good. (author)

  1. Irradiation effects on the storage and disposal of radwaste containing organic ion-exchange media. [3 functional forms of resin - sulfonic acid cation exchanger, quarternary ammonium anion exchanger and mixed bed combination of the two

    Energy Technology Data Exchange (ETDEWEB)

    Swyler, K.J.; Dodge, C.J.; Dayal, R.

    1983-10-01

    Polystyrene-divinylbenzene (PS-DVB) based ion exchangers are commonly used in water demineralization or decontamination operations at nuclear facilities. Self-irradiation from sorbed radionuclides may affect the properties of radwaste containing these ion-exchange media. The effects of external irradiation on anion, cation, and mixed bed PS-DVB ion exchangers have been investigated under conditions relevant to radwaste storage and disposal. Three effects are emphasized in the present report: (1) release of acids, radionuclides or chemically aggressive species through radiolytic attack on the functional group, (2) radiolytic generation/uptake of corrosive or combustible gases, (3) effect of irradiation on solidification of resins in cement. Special consideration was placed on external variables such as radiation dose rate, resin chemical loading and moisture conditions, accessibility to atmospheric oxygen, and interactions in multicomponent systems. Such variables may affect the correspondence between laboratory results and field performance. 40 references, 24 figures, 28 tables.

  2. Artificial liver support for postoperative hepatic failure with anion exchange resin (BR-601).

    OpenAIRE

    Sakagami,Kenichi; MIYAZAKI, MASASHI; Matsuoka, Junji; Shiozaki,Shigehiro; Saito, Shinya; Orita,Kunzo

    1986-01-01

    An artificial liver support system for plasma exchange and plasma perfusion through BR-601 resin using a membrane separator was applied to 5 patients with postoperative liver failure. Percent absorption of total and direct bilirubin, and of bile acids were 77.1 +/- 6.4, 78.4 +/- 6.1, and 93.4 +/- 3.6%, respectively, when 250 ml of plasma was treated. Percent reductions in total and direct bilirubin, and in bile acids were 24.5 +/- 5.8, 25.5 +/- 5.8 and 30.9 +/- 8.5%, respectively. In contrast...

  3. Boron enrichment by ion exchange with Dowex 1X8 anion resin

    International Nuclear Information System (INIS)

    An isotopic separation pilot plant with five ion exchange columns interconnected in series were designed and built in the IEN. The boric acid solution is introduced in the separation columns until it reaches a absorbing zone lenght which is sufficient to obtain the desired boron-10 isotopic concentration. The boric acid absorbing zone movement is provided by the injection of a diluted hydrochloric acid solution, which replces the boric acid troughout the columns to its total lenght. The enriched boron-10 and the depleted boron are located in the final boundary and in the initial position of the absorbing zones, respectively. (author). 6 refs

  4. Synthesis and anion exchange properties of a Zn/Ni double hydroxide salt with a guarinoite structure

    International Nuclear Information System (INIS)

    In this study, the first route to synthesize a compound with the guarinoite structure (Zn,Co,Ni)6(SO4)(OH,Cl)10.5H2O is reported. Zn/Ni guarinoite is obtained from the reaction of NiSO4.7H2O with solid ZnO in aqueous solution. The resulting green Zn/Ni guarinoite ((Zn3.52Ni1.63)(SO4)1.33(OH7.64).4.67H2O) was characterized by X-ray diffraction, infrared spectrometry, UV-Visible spectrometry and thermal analysis. It is shown that its structure is similar to the one described for the layered Zn sulfate hydroxide hydrate, i.e. brucite layers with 1/4 empty octahedra presenting tetrahedrally coordinated divalent atoms above and below the empty octahedra. Ni atoms are located in the octahedra and zinc atoms in tetrahedra and octahedra. In this structure the exchangeable anions are located at the apex of tetrahedra. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) observations show that the Zn/Ni guarinoite is composed of aggregates of hexagonal plates of several hundreds of nanometers. Due to its interest for industrial or environmental applications, the exchange of sulfate groups by carbonates has been investigated. Results show a limited exchange and a higher affinity of the Zn/Ni guarinoite for sulfates compared to carbonates. - Graphical abstract: SEM micrograph (secondary electrons) of the synthesized Zn/Ni guarinoite showing that aggregates are composed of small plate-like particles.

  5. Preparation of silica nanocomposite anion-exchange membranes with low vanadium-ion crossover for vanadium redox flow batteries

    International Nuclear Information System (INIS)

    Highlights: • The permeability of vanadium ions through the silica nanocomposite AEM (SNAEM) is ten times lower than that for Nafion 115. • The rates of self-discharge and capacity fading of the VRFB are substantially reduced with the use of the SNAEM. • The Coulombic and energy efficiencies are as high as 92% and 73%, respectively, at 40 mA cm−2. -- Abstract: Crossover of vanadium ions through the membranes of all-vanadium redox flow batteries (VRFB) is an issue that limits the performance of this type of flow battery. This paper reports on the preparation of a sol–gel derived silica nanocomposite anion exchange membrane (AEM) for VRFBs. The EDS and FT-IR characterizations confirm the presence and the uniformity of the silica nanoparticles formed in the membrane via an in situ sol–gel process. The properties of the obtained membrane, including the ion-exchange capacity, the area resistance, and the water uptake, are evaluated and compared to the pristine AEM and the Nafion cation exchange membrane (CEM). The experimental results show that the permeability of the vanadium ions through the silica nanocomposite AEM is about 20% lower than that of the pristine AEM, and one order of magnitude lower than that of the Nafion CEM. As a result, the rates of self-discharge and the capacity fading of the VRFB are substantially reduced. The Coulombic and energy efficiencies at a current density of 40 mA cm−2 are, respectively, as high as 92% and 73%

  6. Artificial liver support for postoperative hepatic failure with anion exchange resin (BR-601.

    Directory of Open Access Journals (Sweden)

    Sakagami,Kenichi

    1986-10-01

    Full Text Available An artificial liver support system for plasma exchange and plasma perfusion through BR-601 resin using a membrane separator was applied to 5 patients with postoperative liver failure. Percent absorption of total and direct bilirubin, and of bile acids were 77.1 +/- 6.4, 78.4 +/- 6.1, and 93.4 +/- 3.6%, respectively, when 250 ml of plasma was treated. Percent reductions in total and direct bilirubin, and in bile acids were 24.5 +/- 5.8, 25.5 +/- 5.8 and 30.9 +/- 8.5%, respectively. In contrast, percent reductions in total and direct bilirubin, and in bile acids by plasma exchange were 30.9 +/- 13.3, 34.5 +/- 12.5 and 24.2 +/- 8.5%, respectively. The coma grade was improved in 4 out of 5 cases, but unfortunately the patients did not recover. In conclusion, plasma perfusion through BR-601 resin is expected to play a promising role in artificial liver support systems because of its capacity to absorb bilirubin and bile acids.

  7. Cationic Covalent Organic Frameworks: A Simple Platform of Anionic Exchange for Porosity Tuning and Proton Conduction.

    Science.gov (United States)

    Ma, Heping; Liu, Bailing; Li, Bin; Zhang, Liming; Li, Yang-Guang; Tan, Hua-Qiao; Zang, Hong-Ying; Zhu, Guangshan

    2016-05-11

    Mimicking proton conduction mechanism of Nafion to construct novel proton-conducting materials with low cost and high proton conductivity is of wide interest. Herein, we have designed and synthesized a cationic covalent organic framework with high thermal and chemical stability by combining a cationic monomer, ethidium bromide (EB) (3,8-diamino-5-ethyl-6-phenylphenanthridinium bromide), with 1,3,5-triformylphloroglucinol (TFP) in Schiff base reactions. This is the first time that the stable cationic crystalline frameworks allowed for the fabrication of a series of charged COFs (EB-COF:X, X = F, Cl, Br, I) through ion exchange processes. Exchange of the extra framework ions can finely modulate the COFs' porosity and pore sizes at nanoscale. More importantly, by introducing PW12O40(3-) into this porous cationic framework, we can greatly enhance the proton conductivity of ionic COF-based material. To the best of our knowledge, EB-COF:PW12 shows the best proton conductivity at room temperature among ever reported porous organic materials. PMID:27094048

  8. Arsenate Adsorption by Hydrous Ferric Oxide Nanoparticles Embedded in Cross-linked Anion Exchanger: Effect of the Host Pore Structure.

    Science.gov (United States)

    Li, Hongchao; Shan, Chao; Zhang, Yanyang; Cai, Jianguo; Zhang, Weiming; Pan, Bingcai

    2016-02-10

    Three composite adsorbents were fabricated via confined growth of hydrous ferric oxide (HFO) nanoparticles within cross-linked anion exchangers (NS) of different pore size distributions to investigate the effect of host pore structure on the adsorption of As(V). With the decrease in the average pore size of the NS hosts from 38.7 to 9.2 nm, the mean diameter of the confined HFO nanoparticles was lessened from 31.4 to 11.6 nm as observed by transmission electron microscopy (TEM), while the density of active surface sites was increased due to size-dependent effect proved by potentiometric titration. The adsorption capacity of As(V) yielded by Sips model was elevated from 24.2 to 31.6 mg/g via tailoring the pore size of the NS hosts, and the adsorption kinetics was slightly accelerated with the decrease of pore size in background solution containing 500 mg/L of Cl(-). Furthermore, the enhanced adsorption of As(V) was achieved over a wide pH range from 3 to 10, as well as in the presence of competing anions including Cl(-), SO4(2-), HCO3(-), NO3(-) (up to 800 mg/L), and PO4(3-) (up to 10 mg P/L). In addition, the fixed-bed working capacity increased from 2200 to 2950 bed volumes (BV) owing to the size confinement effect, which did not have adverse effect on the desorption of As(V) as the cumulative desorption efficiency reached 94% with 10 BV of binary solution (5% NaOH + 5% NaCl) for all the three adsorbents. Therefore, this study provided a promising strategy to regulate the reactivity of the nanoparticles via the size confinement effect of the host pore structure. PMID:26765396

  9. New inorganic (an)ion exchangers with a higher affinity for arsenate and a competitive removal capacity towards fluoride, bromate, bromide, selenate, selenite, arsenite and borate

    KAUST Repository

    Chubar, Natalia

    2011-12-01

    Highly selective materials and effective technologies are needed to meet the increasingly stronger drinking water standards for targeted ionic species. Inorganic ion exchangers based on individual and mixed-metal hydrous oxides (or mixed adsorbents that contain inorganic ion exchangers in their composition) are adsorptive materials that are capable of lowering the concentrations of anionic contaminants, such as H 2AsO 4 -, H 3AsO 3, F -, Br -, BrO 3 -, HSeO 4 -, HSeO 3 - and H 3BO 3, to 10 μg/L or less. To achieve a higher selectivity towards arsenate, a new ion exchanger based on Mg-Al hydrous oxides was developed by a novel, cost-effective and environmentally friendly synthesis method via a non-traditional (alkoxide-free) sol-gel approach. The exceptional adsorptive capacity of the Mg-Al hydrous oxides towards H 2AsO 4 - (up to 200 mg[As]/gdw) is due to the high affinity of this sorbent towards arsenate (steep equilibrium isotherms) and its fast adsorption kinetics. Because of the mesoporous (as determined by N 2 adsorption and SEM) and layered (as determined by XRD and FTIR) structure of the ion-exchange material as well as the abundance of anion exchange sites (as determined by XPS and potentiometric titration) on its surface the material demonstrated very competitive (or very high) removal capacity towards other targeted anions, including fluoride, bromide, bromate, selenate, selenite, and borate. © 2011 IWA Publishing.

  10. 3-Methyltrimethylammonium poly(2,6-dimethyl-1,4-phenylene oxide) based anion exchange membrane for alkaline polymer electrolyte fuel cells

    Indian Academy of Sciences (India)

    K Hari Gopi; S Gouse Peera; S D Bhat; P Sridhar; S Pitchumani

    2014-06-01

    Hydroxyl ion (OH–) conducting anion exchange membranes based on modified poly (phenylene oxide) are fabricated for their application in alkaline polymer electrolyte fuel cells (APEFCs). In the present study, chloromethylation of poly(phenylene oxide) (PPO) is performed by aryl substitution rather than benzyl substitution and homogeneously quaternized to form an anion exchange membrane (AEM). 1H NMR and FT–IR studies reveal successful incorporation of the above groups in the polymer backbone. The membrane is characterized for its ion exchange capacity and water uptake. The membrane formed by these processes show good ionic conductivity and when used in fuel cell exhibited an enhanced performance in comparison with the state-of-the-art commercial AHA membrane. A peak power density of 111 mW/cm2 at a load current density of 250 mA/cm2 is obtained for PPO based membrane in APEFCs at 30 °C.

  11. Efficiencies and Optimization of Weak Base Anion Ion-Exchange Resin for Groundwater Hexavalent Chromium Removal at Hanford

    International Nuclear Information System (INIS)

    The U.S. Department of Energy's (DOE's) contractor, CH2M HILL Plateau Remediation Company, has successfully converted a series of groundwater treatment facilities to use a new treatment resin that is delivering more than $3 million in annual cost savings and efficiency in treating groundwater contamination at the DOE Hanford Site in southeastern Washington State. During the production era, the nuclear reactors at the Hanford Site required a continuous supply of high-quality cooling water during operations. Cooling water consumption ranged from about 151,417 to 378,541 L/min (40,000 to 100,000 gal/min) per reactor, depending on specific operating conditions. Water from the Columbia River was filtered and treated chemically prior to use as cooling water, including the addition of sodium dichromate as a corrosion inhibitor. Hexavalent chromium was the primary component of the sodium dichromate and was introduced into the groundwater at the Hanford Site as a result of planned and unplanned discharges from the reactors starting in 1944. Groundwater contamination by hexavalent chromium and other contaminants related to nuclear reactor operations resulted in the need for groundwater remedial actions within the Hanford Site reactor areas. Beginning in 1995, groundwater treatment methods were evaluated, leading to the use of pump-and-treat facilities with ion exchange using Dowex 21K, a regenerable, strong-base anion exchange resin. This required regeneration of the resin, which was performed offsite. In 2008, DOE recognized that regulatory agreements would require significant expansion for the groundwater chromium treatment capacity. As a result, CH2M HILL performed testing at the Hanford Site in 2009 and 2010 to demonstrate resin performance in the specific groundwater chemistry at different waste sites. The testing demonstrated that a weak-base anion, single-use resin, specifically ResinTech SIR-700 ®, was effective at removing chromium, had a significantly higher

  12. Efficiencies and Optimization of Weak Base Anion Ion-Exchange Resin for Groundwater Hexavalent Chromium Removal at Hanford

    Energy Technology Data Exchange (ETDEWEB)

    Nesham, Dean O.; Ivarson, Kristine A.; Hanson, James P.; Miller, Charles W.; Meyers, P.; Jaschke, Naomi M.

    2014-02-03

    The U.S. Department of Energy’s (DOE’s) contractor, CH2M HILL Plateau Remediation Company, has successfully converted a series of groundwater treatment facilities to use a new treatment resin that is delivering more than $3 million in annual cost savings and efficiency in treating groundwater contamination at the DOE Hanford Site in southeastern Washington State. During the production era, the nuclear reactors at the Hanford Site required a continuous supply of high-quality cooling water during operations. Cooling water consumption ranged from about 151,417 to 378,541 L/min (40,000 to 100,000 gal/min) per reactor, depending on specific operating conditions. Water from the Columbia River was filtered and treated chemically prior to use as cooling water, including the addition of sodium dichromate as a corrosion inhibitor. Hexavalent chromium was the primary component of the sodium dichromate and was introduced into the groundwater at the Hanford Site as a result of planned and unplanned discharges from the reactors starting in 1944. Groundwater contamination by hexavalent chromium and other contaminants related to nuclear reactor operations resulted in the need for groundwater remedial actions within the Hanford Site reactor areas. Beginning in 1995, groundwater treatment methods were evaluated, leading to the use of pump-and-treat facilities with ion exchange using Dowex™ 21K, a regenerable, strong-base anion exchange resin. This required regeneration of the resin, which was performed offsite. In 2008, DOE recognized that regulatory agreements would require significant expansion for the groundwater chromium treatment capacity. As a result, CH2M HILL performed testing at the Hanford Site in 2009 and 2010 to demonstrate resin performance in the specific groundwater chemistry at different waste sites. The testing demonstrated that a weak-base anion, single-use resin, specifically ResinTech SIR-700 ®, was effective at removing chromium, had a significantly

  13. Protein adsorption on ion exchange resins and monoclonal antibody charge variant modulation.

    Science.gov (United States)

    Guélat, Bertrand; Khalaf, Rushd; Lattuada, Marco; Costioli, Matteo; Morbidelli, Massimo

    2016-05-20

    A novel multicomponent adsorption equilibrium model for proteins on ion-exchange resins is developed on a statistical thermodynamic basis including surface coverage effects and protein-resin and protein-protein interactions. The resulting model exhibits a general competitive Langmuirian behavior and was applied to the study and optimization of the separation of monoclonal antibody charge variants on two strong cation exchangers. The model accounts explicitly for the effect of both pH and salt concentration, and its parameters can be determined in diluted conditions, that is, through physically sound assumptions, all model parameters can be obtained using solely experiments in diluted conditions, and be used to make predictions in overloaded conditions. The parameterization of the model and optimization of the separation is based on a two-step approach. First, gradient experiments in diluted conditions are undertaken in order to determine the model parameters. Based on these experiments and on information about the proteins of interest and the stationary phase used, all the model parameters can be estimated. Second, using the parameterized model, an initial Pareto optimization is undertaken where overloaded operating conditions are investigated. Experiments from this Pareto set are then used to refine the estimation of the model parameters. A second Pareto optimization can then be undertaken, this time with the refined parameters. This can be repeated until a satisfactory set of model parameters is found. This iterative approach is shown to be extremely efficient and to provide large amounts of knowledge based on only a few experiments. It is shown that due to the strong physical foundation of the model and the very low number of adjustable parameters, the number of iterations is expected to be at most two or three. Furthermore, the model based tool is improved as more experimental knowledge is provided, allowing for better estimations of the chromatographic

  14. Single-Crystal-to-Single-Crystal Anion Exchange in a Gadolinium MOF: Incorporation of POMs and [AuCl4]−

    Directory of Open Access Journals (Sweden)

    Javier López-Cabrelles

    2016-04-01

    Full Text Available The encapsulation of functional molecules inside porous coordination polymers (also known as metal-organic frameworks, MOFs has become of great interest in recent years at the field of multifunctional materials. In this article, we present a study of the effects of size and charge in the anion exchange process of a Gd based MOF, involving molecular species like polyoxometalates (POMs, and [AuCl4]−. This post-synthetic modification has been characterized by IR, EDAX, and single crystal diffraction, which have provided unequivocal evidence of the location of the anion molecules in the framework.

  15. Evaluation and application of anion exchange resins to measure groundwater uranium flux at a former uranium mill site.

    Science.gov (United States)

    Stucker, Valerie; Ranville, James; Newman, Mark; Peacock, Aaron; Cho, Jaehyun; Hatfield, Kirk

    2011-10-15

    Laboratory tests and a field validation experiment were performed to evaluate anion exchange resins for uranium sorption and desorption in order to develop a uranium passive flux meter (PFM). The mass of uranium sorbed to the resin and corresponding masses of alcohol tracers eluted over the duration of groundwater installation are then used to determine the groundwater and uranium contaminant fluxes. Laboratory based batch experiments were performed using Purolite A500, Dowex 21K and 21K XLT, Lewatit S6328 A resins and silver impregnated activated carbon to examine uranium sorption and extraction for each material. The Dowex resins had the highest uranium sorption, followed by Lewatit, Purolite and the activated carbon. Recoveries from all ion exchange resins were in the range of 94-99% for aqueous uranium in the environmentally relevant concentration range studied (0.01-200 ppb). Due to the lower price and well-characterized tracer capacity, Lewatit S6328 A was used for field-testing of PFMs at the DOE UMTRA site in Rifle, CO. The effect on the flux measurements of extractant (nitric acid)/resin ratio, and uranium loading were investigated. Higher cumulative uranium fluxes (as seen with concentrations>1 ug U/gram resin) yielded more homogeneous resin samples versus lower cumulative fluxes (<1 ug U/gram resin), which caused the PFM to have areas of localized concentration of uranium. Resin homogenization and larger volume extractions yield reproducible results for all levels of uranium fluxes. Although PFM design can be improved to measure flux and groundwater flow direction, the current methodology can be applied to uranium transport studies. PMID:21798572

  16. Mitigating arsenic crisis in the developing world: role of robust, reusable and selective hybrid anion exchanger (HAIX).

    Science.gov (United States)

    German, Michael; Seingheng, Hul; SenGupta, Arup K

    2014-08-01

    In trying to address the public health crisis from the lack of potable water, millions of tube wells have been installed across the world. From these tube wells, natural groundwater contamination from arsenic regularly puts at risk the health of over 100 million people in South and Southeast Asia. Although there have been many research projects, awards and publications, appropriate treatment technology has not been matched to ground level realities and water solutions have not scaled to reach millions of people. For thousands of people from Nepal to India to Cambodia, hybrid anion exchange (HAIX) resins have provided arsenic-safe water for up to nine years. Synthesis of HAIX resins has been commercialized and they are now available globally. Robust, reusable and arsenic-selective, HAIX has been in operation in rural communities over numerous cycles of exhaustion-regeneration. All necessary testing and system maintenance is organized by community-level water staff. Removed arsenic is safely stored in a scientifically and environmentally appropriate manner to prevent future hazards to animals or people. Recent installations have shown the profitability of HAIX-based arsenic treatment, with capital payback periods of only two years in ideal locations. With an appropriate implementation model, HAIX-based treatment can rapidly scale and provide arsenic-safe water to at-risk populations. PMID:24321388

  17. A pilot-scale evaluation of magnetic ion exchange treatment for removal of natural organic material and inorganic anions.

    Science.gov (United States)

    Boyer, Treavor H; Singer, Philip C

    2006-08-01

    The objective of this research was to evaluate a magnetic ion exchange process (MIEX) for the removal of natural organic material (NOM) and bromide on a continuous-flow pilot-scale basis under different operating conditions and raw water characteristics. The most important operating variable was the effective resin dose (ERD), which is the product of the steady-state resin concentration in the contactor and the regeneration ratio. The raw water employed in this study had a moderate concentration of ultraviolet (UV)-absorbing substances and dissolved organic carbon (DOC), and a low turbidity, alkalinity, and concentration of competing anionic species. Experiments were conducted using the ambient raw water and raw water spiked with bromide, chloride, and sulfate. Substantial removal of UV-absorbing substances and DOC was achieved at ERDs as low as 0.16mL/L. Moderate bromide removal was achieved, depending on the ERD. Increasing the sulfate concentration resulted in decreased removal of UV-absorbing substances, DOC, and bromide. Consistent results were observed between the continuous-flow pilot plant tests and batch equilibrium studies. PMID:16844182

  18. Oxygen evolution reaction characteristics of synthetic nickel-cobalt-oxide electrodes for alkaline anion-exchange membrane water electrolysis

    Science.gov (United States)

    Koo, Tae Woo; Park, ChanSu; Kim, Yang Do; Lee, Dooyong; Park, Sungkyun; Lee, Jae Ho; Choi, Sung Mook; Choi, Chul Young

    2015-11-01

    A polymer electrolyte membrane water electrolysis system can produce high-purity hydrogen gases in a highly efficient manner. However, the level of hydrogen gas production is still small. In addition, noble-metal catalysts for the reaction in acidic environments, as well as an additional drying step to remove water contained in the hydrogen, are required. Therefore, water electrolysis system with high efficiency and lower cost, an alkaline anion-exchange membrane system that can produce high-purity hydrogen without a noble-metal catalyst, is needed. Nano-size NiCo2O4 powders were prepared by using a sol-gel method to achieve an efficient and economical water electrolysis system. When the powder was calcined at 450 °C, the crystallinity and the cyclic voltammogram measurement showed the best values. In addition, the 15-wt.% polytetrafluoroethylene mixed NiCo2O4 powders exhibited the largest cyclic voltammetry active area and the highest oxygen evolution reaction activity with the appropriate stability.

  19. Comparison of displacement versus gradient mode for separation of a complex protein mixture by anion-exchange chromatography.

    Science.gov (United States)

    Ahrends, Robert; Lichtner, Björn; Buck, Friedrich; Hildebrand, Diana; Kotasinska, Marta; Kohlbacher, Oliver; Kwiatkowski, Marcel; Wagner, Moritz; Trusch, Maria; Schlüter, Hartmut

    2012-07-15

    Liquid chromatography is often the method of choice for the analysis of proteins in their native state. Nevertheless compared to two-dimensional electrophoresis, the resolution of common chromatographic techniques is low. Liquid chromatography in the displacement mode has previously been shown to offer higher resolution and to elute proteins in the high concentrations. In this study we compared to what extend displacement mode was a suitable alternative to gradient mode for the separation of a complex protein mixture using anion-exchange displacement chromatography and if it is therefore helpful for proteomic investigations. Hence we analyzed the qualitative protein composition of each fraction by tryptic digestion of the proteins, analysis of the tryptic peptides by liquid chromatography coupled to mass spectrometry followed by data base analysis and by measuring the elution profiles of 22 selected proteins with selected reaction monitoring mass spectrometry. In the fractions of displacement mode a significantly higher number of identified proteins (51 versus 16) was yielded in comparison to gradient mode. The resolution of displacement chromatography was slightly lower than of gradient chromatography for many but not for all proteins. The selectivities of displacement mode and gradient mode are very different. In conclusion displacement chromatography is a well suited alternative for top-down proteomic approaches which start with separating intact proteins first prior to mass spectrometric analysis of intact or digested proteins. The significant orthogonality of both modes may be used in the future for combining them in multidimensional fractionation procedures. PMID:22727752

  20. Quaternized adamantane-containing poly(aryl ether ketone) anion exchange membranes for vanadium redox flow battery applications

    Science.gov (United States)

    Zhang, Bengui; Zhang, Shouhai; Weng, Zhihuan; Wang, Guosheng; Zhang, Enlei; Yu, Ping; Chen, Xiaomeng; Wang, Xinwei

    2016-09-01

    Quaternized adamantane-containing poly(aryl ether ketone) anion exchange membranes (QADMPEK) are prepared and investigated for vanadium redox flow batteries (VRFB) application. The bulky, rigid and highly hydrophobic adamantane segment incorporated into the backbone of membrane material makes QADMPEK membranes have low water uptake and swelling ratio, and the as-prepared membranes display significantly lower permeability of vanadium ions than that of Nafion117 membrane. As a consequence, the VRFB cell with QADMPEK-3 membrane shows higher coulombic efficiency (99.4%) and energy efficiency (84.0%) than those for Nafion117 membrane (95.2% and 80.5%, respectively) at the current density of 80 mA cm-2. Furthermore, at a much higher current density of 140 mA cm-2, QADMPEK membrane still exhibits better coulombic efficiency and energy efficiency than Nafion117 membrane (coulombic efficiency 99.2% vs 96.5% and energy efficiency 76.0% vs 74.0%). Moreover, QADMPEK membranes show high stability in in-situ VRFB cycle test and ex-situ oxidation stability test. These results indicate that QADMPEK membranes are good candidates for VRFB applications.

  1. Identification of low-abundance proteins via fractionation of the urine proteome with weak anion exchange chromatography

    Directory of Open Access Journals (Sweden)

    Chen Jeff

    2011-04-01

    Full Text Available Abstract Background Low-abundance proteins are difficultly observed on the two-dimensional gel electrophoresis (2-DE maps of urine proteome, because they are usually obscured by high-abundance proteins such as albumin and immunoglobulin. In this study, a novel fractionation method was developed for enriching low-abundance proteins by removing high-abundance proteins and progressive elution with salts of various concentrations. Results Stepwise weak anion exchange (WAX chromatography, which applied DEAE-Sephacel resin with non-fixed volume elution, was used to fractionate urine proteome prior to performing 2-DE. Urine proteome was separated into four fractions by progressively eluting the column with 0 M, 50 mM, 100 mM, and 1 M NaCl solutions. Most of the heavy and light immunoglobulin chains appeared in the eluent. After the high-abundance proteins were removed, various low-abundance proteins were enriched and could be easily identified. The potential of this method for obtaining diversified fractionations was demonstrated by eluting the column separately with Na2SO4 and MgCl2 solutions. The 2-DE maps of the fractions eluted with these different salt solutions of identical ionic strength revealed markedly different stain patterns. Conclusion The present study demonstrated that this fractionation method could be applied for purposes of enriching low-abundance proteins and obtaining diversified fractionations of urine, and potentially other proteomes.

  2. Improvement of sugar analysis sensitivity using anion-exchange chromatography-electrospray ionization mass spectrometry with sheath liquid interface.

    Science.gov (United States)

    Xu, Xian-Bing; Liu, Ding-Bo; Guo, Xiao Ming; Yu, Shu-Juan; Yu, Pei

    2014-10-31

    A novel interface that enables high-performance anion-exchange chromatography (HPAEC) to be coupled with electrospray ionization (ESI) mass spectrometry (MS) is reported. A sheath liquid consisting of 50mM NH4Ac in isopropanol with 0.05% acetic acid, infused at a flow rate of 3μL/min at the tip of the electrospray probe, requires less ESI source cleaning and promotes efficient ionization of mono- and di-carbohydrates. The results suggest that use of a sheath liquid interface rather than a T-joint allows volatile ammonium salts to replace non-volatile metal salts as modifiers for improving sugar ESI signals. The efficient ionization of mono- and di-carbohydrates in the ESI source is affected by the sheath liquid properties such as buffer concentration and type of organic solvent. HPAEC-ESI-MS was used for the analysis of monocarbohydrates in pectins, particularly co-eluted sugars, and the performance was evaluated. Addition of a make-up solution through the sheath liquid interface proved to be an efficient tool for enhancing the intensities of sugars analyzed using HPAEC-ESI-MS. PMID:25246101

  3. Assay for inorganic pyrophosphate in chondrocyte culture using anion-exchange high-performance liquid chromatography and radioactive orthophosphate labeling

    International Nuclear Information System (INIS)

    A method is described for determination of inorganic pyrophosphate (PPi) in cell culture medium and in rabbit articular chondrocytes grown in the presence of radioactive orthophosphate (32Pi). Intra- and extracellular 32PPi formed was measured using high-performance liquid chromatographic (HPLC) separation of the PPi from orthophosphate (Pi) and other phosphate-containing compounds. The chromatographic separation on a weak anion-exchange column is based on the extent to which various phosphate compounds form complexes with Mg2+ at low pH and the rate at which such formation occurs. These complexes are eluted more readily than the uncomplexed compounds. Best results were obtained using a simultaneous gradient of Mg2+ ions and ionic strength. In this case separation of small amounts of PPi from a large excess of Pi was possible without prior removal of Pi or extraction of the PPi fraction. The assay is also useful for measurement of inorganic pyrophosphatase activity. The sensitivity of the assay depends on the specific activity of the added 32Pi and on the culture conditions, but is comparable with the most sensitive of the enzymatic assays. Sample preparation, particularly deproteinization, proved to be of importance. The losses of PPi which occur during procedures of this sort due to hydrolysis and coprecipitation were quantitated

  4. Dissolved organic matter removal using magnetic anion exchange resin treatment on biological effluent of textile dyeing wastewater.

    Science.gov (United States)

    Fan, Jun; Li, Haibo; Shuang, Chendong; Li, Wentao; Li, Aimin

    2014-08-01

    This study investigated the removal of dissolved organic matter (DOM) from real dyeing bio-treatment effluents (DBEs) with the use of a novel magnetic anion exchange resin (NDMP). DOMs in two typical DBEs were fractionized using DAX-8/XAD-4 resin and ultrafiltration membranes. The hydrophilic fractions and the low molecular weight (MW) (50%) of DOMs for the two effluents. The hydrophilic and low MW fractions of both effluents were the greatest contributors of specific UV254 absorbance (SUVA254), and the SUVA254 of DOM fractions decreased with hydrophobicity and MW. Two DBEs exhibited acute and chronic biotoxicities. Both acute and chronic toxicities of DOM fractions increased linearly with the increase of SUVA254 value. Kinetics of dissolved organic carbon (DOC) removal via NDMP treatment was performed by comparing it with that of particle active carbon (PAC). Results indicated that the removal of DOC from DBEs via NDMP was 60%, whereas DOC removals by PAC were lower than 15%. Acidic organics could be significantly removed with the use of NDMP. DOM with large MW in DBE could be removed significantly by using the same means. Removal efficiency of NDMP for DOM decreased with the decrease of MW. Compared with PAC, NDMP could significantly reduce the acute and chronic bio-toxicities of DBEs. NaCl/NaOH mixture regenerants, with selected concentrations of 10% NaCl (m/m)/1% NaOH (m/m), could improve desorption efficiency. PMID:25108712

  5. Ion Mobility Spectrometry-Hydrogen Deuterium Exchange Mass Spectrometry of Anions: Part 3. Estimating Surface Area Exposure by Deuterium Uptake.

    Science.gov (United States)

    Khakinejad, Mahdiar; Kondalaji, Samaneh Ghassabi; Donohoe, Gregory C; Valentine, Stephen J

    2016-03-01

    Gas-phase hydrogen deuterium exchange (HDX), collision cross section (CCS) measurement, and molecular dynamics simulation (MDS) techniques were utilized to develop and compare three methods for estimating the relative surface area exposure of separate peptide chains within bovine insulin ions. Electrosprayed [M - 3H](3-) and [M - 5H](5-) insulin ions produced a single conformer type with respective collision cross sections of 528 ± 5 Å(2) and 808 ± 2 Å(2). [M - 4H](4-) ions were comprised of more compact (Ω = 676 ± 3 Å(2)) and diffuse (i.e., more elongated, Ω = 779 ± 3 Å(2)) ion conformer types. Ions were subjected to HDX in the drift tube using D2O as the reagent gas. Collision-induced dissociation was used to fragment mobility-selected, isotopically labeled [M - 4H](4-) and [M - 5H](5-) ions into the protein subchains. Deuterium uptake levels of each chain can be explained by limited inter-chain isotopic scrambling upon collisional activation. Using nominal ion structures from MDS and a hydrogen accessibility model, the deuterium uptake for each chain was correlated to its exposed surface area. In separate experiments, the per-residue deuterium content for the protonated and deprotonated ions of the synthetic peptide KKDDDDDIIKIIK were compared. The differences in deuterium content indicated the regional HDX accessibility for cations versus anions. Using ions of similar conformational type, this comparison highlights the complementary nature of HDX data obtained from positive- and negative-ion analysis. PMID:26620531

  6. Anion exchange behavior of Ti, Zr, Hf, Nb and Ta as homologues of Rf and Db in mixed HF-acetone solutions

    International Nuclear Information System (INIS)

    We studied in detail the sorption behavior of Ti, Zr, Hf, Nb and Ta on AG 1 anion exchange resin in HF-acetone mixed solutions as a function of organic cosolvent and acid concentrations. Anion exchange behavior was found to be strongly acetone concentration dependent. The distribution coefficients of Ti, Zr, Hf and Nb increased and those of Ta decreased with increasing content of acetone in HF solutions. With increasing HF concentration, anion exchange equilibrium analysis indicated the formation of fluoride complexes of group-4 elements with charge -3 and Ta with charge -2. For Nb the slope of -2 increased up to -5. Optimal conditions for separation of the elements using AIX chromatography were found. Group-4 elements formed MF73- (M = Ti, Zr, Hf) complexes whose sorption decreased Ti > Hf > Zr in reverse order of complex stability. This fact is of particular interest for studying ion exchange behavior of Rf compared to Ti. The advantages of studying chemical properties of Rf and Db in aqueous HF solutions mixed with organic solvents are briefly discussed

  7. Rapid isolation of plutonium in environmental solid samples using sequential injection anion exchange chromatography followed by detection with inductively coupled plasma mass spectrometry.

    Science.gov (United States)

    Qiao, Jixin; Hou, Xiaolin; Roos, Per; Miró, Manuel

    2011-01-31

    This paper reports an automated analytical method for rapid determination of plutonium isotopes ((239)Pu and (240)Pu) in environmental solid extracts. Anion exchange chromatographic columns were incorporated in a sequential injection (SI) system to undertake the automated separation of plutonium from matrix and interfering elements. The analytical results most distinctly demonstrated that the crosslinkage of the anion exchanger is a key parameter controlling the separation efficiency. AG 1-×4 type resin was selected as the most suitable sorbent material for analyte separation. Investigation of column size effect upon the separation efficiency revealed that small-sized (2 mL) columns sufficed to handle up to 50 g of environmental soil samples. Under the optimum conditions, chemical yields of plutonium exceeded 90% and the decontamination factors for uranium, thorium and lead ranged from 10(3) to 10(4). The determination of plutonium isotopes in three standard/certified reference materials (IAEA-375 soil, IAEA-135 sediment and NIST-4359 seaweed) and two reference samples (Irish Sea sediment and Danish soil) revealed a good agreement with reference/certified values. The SI column-separation method is straightforward and less labor intensive as compared with batch-wise anion exchange chromatographic procedures. Besides, the automated method features low consumption of ion-exchanger and reagents for column washing and elution, with the consequent decrease in the generation of acidic waste, thus bearing green chemical credentials. PMID:21168558

  8. Rapid isolation of plutonium in environmental solid samples using sequential injection anion exchange chromatography followed by detection with inductively coupled plasma mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Qiao Jixin, E-mail: jixin.qiao@risoe.d [Radiation Research Division, Riso National Laboratory for Sustainable Energy, Technical University of Denmark, DK-4000 Roskilde (Denmark); Hou Xiaolin; Roos, Per [Radiation Research Division, Riso National Laboratory for Sustainable Energy, Technical University of Denmark, DK-4000 Roskilde (Denmark); Miro, Manuel [Department of Chemistry, Faculty of Sciences, University of the Balearic Islands, Carretera de Valldemossa km. 7.5, E-07122 Palma de Mallorca, Illes Balears (Spain)

    2011-01-31

    This paper reports an automated analytical method for rapid determination of plutonium isotopes ({sup 239}Pu and {sup 240}Pu) in environmental solid extracts. Anion exchange chromatographic columns were incorporated in a sequential injection (SI) system to undertake the automated separation of plutonium from matrix and interfering elements. The analytical results most distinctly demonstrated that the crosslinkage of the anion exchanger is a key parameter controlling the separation efficiency. AG 1-x4 type resin was selected as the most suitable sorbent material for analyte separation. Investigation of column size effect upon the separation efficiency revealed that small-sized (2 mL) columns sufficed to handle up to 50 g of environmental soil samples. Under the optimum conditions, chemical yields of plutonium exceeded 90% and the decontamination factors for uranium, thorium and lead ranged from 10{sup 3} to 10{sup 4}. The determination of plutonium isotopes in three standard/certified reference materials (IAEA-375 soil, IAEA-135 sediment and NIST-4359 seaweed) and two reference samples (Irish Sea sediment and Danish soil) revealed a good agreement with reference/certified values. The SI column-separation method is straightforward and less labor intensive as compared with batch-wise anion exchange chromatographic procedures. Besides, the automated method features low consumption of ion-exchanger and reagents for column washing and elution, with the consequent decrease in the generation of acidic waste, thus bearing green chemical credentials.

  9. Rapid isolation of plutonium in environmental solid samples using sequential injection anion exchange chromatography followed by detection with inductively coupled plasma mass spectrometry

    International Nuclear Information System (INIS)

    This paper reports an automated analytical method for rapid determination of plutonium isotopes (239Pu and 240Pu) in environmental solid extracts. Anion exchange chromatographic columns were incorporated in a sequential injection (SI) system to undertake the automated separation of plutonium from matrix and interfering elements. The analytical results most distinctly demonstrated that the crosslinkage of the anion exchanger is a key parameter controlling the separation efficiency. AG 1-x4 type resin was selected as the most suitable sorbent material for analyte separation. Investigation of column size effect upon the separation efficiency revealed that small-sized (2 mL) columns sufficed to handle up to 50 g of environmental soil samples. Under the optimum conditions, chemical yields of plutonium exceeded 90% and the decontamination factors for uranium, thorium and lead ranged from 103 to 104. The determination of plutonium isotopes in three standard/certified reference materials (IAEA-375 soil, IAEA-135 sediment and NIST-4359 seaweed) and two reference samples (Irish Sea sediment and Danish soil) revealed a good agreement with reference/certified values. The SI column-separation method is straightforward and less labor intensive as compared with batch-wise anion exchange chromatographic procedures. Besides, the automated method features low consumption of ion-exchanger and reagents for column washing and elution, with the consequent decrease in the generation of acidic waste, thus bearing green chemical credentials.

  10. Organic anion transporting polypeptides OATP1B1 and OATP1B3 and their genetic variants influence the pharmacokinetics and pharmacodynamics of raloxifene

    Directory of Open Access Journals (Sweden)

    Trdan Lušin Tina

    2012-04-01

    Full Text Available Abstract Background Raloxifene, a selective estrogen receptor modulator, exhibits quite large and unexplained interindividual variability in pharmacokinetics and pharmacodynamics. The aim of this study was to determine the role of organic-anion transporting polypeptides OATP1B1 and OATP1B3 and their genetic variants in the pharmacokinetics and pharmacodynamics of raloxifene. Methods To test the role of OATP1B1 and OATP1B3 transporters on hepatic uptake of raloxifene and its metabolites an in vitro model of Chinese Hamster Ovary cells expressing OATP1B1 or OATP1B3 was employed. The influence of OATP1B1 and OATP1B3 genetic variants on in vivo pharmacokinetics and pharmacodynamics was evaluated in 53 osteoporotic postmenopausal women treated with raloxifene. Results Our in vitro results showed that raloxifene and two of the three metabolites, raloxifene-4'-β-glucuronide (M2 and raloxifene-6,4'-diglucuronide (M3, interact with OATP1B1 and OATP1B3. Higher M3 and total raloxifene serum concentrations in patients correlated with lower serum levels of bone resorption marker, serum C-terminal telopeptide fragments of type I collagen, indicating a higher antiresorptive effect of raloxifene. Higher concentrations of M2 correlated with higher increase of lumbar spine bone mineral density supporting the raloxifene vertebral fracture specific protection effect. Finally, raloxifene, M3 and total raloxifene serum concentrations were significantly higher in patients with SLCO1B1 c.388A > G polymorphism and *1b haplotype implicating a considerable genetic effect on pharmacokinetics and pharmacodynamics of raloxifene. Conclusions These findings indicate that SLCO1B1 c.388A > G polymorphism could play an important role in pharmacokinetics and pharmacodynamics of raloxifene.

  11. Recent Advances in Solid Catalysts Obtained by Metalloporphyrins Immobilization on Layered Anionic Exchangers: A Short Review and Some New Catalytic Results

    Directory of Open Access Journals (Sweden)

    Shirley Nakagaki

    2016-02-01

    Full Text Available Layered materials are a very interesting class of compounds obtained by stacking of two-dimensional layers along the basal axis. A remarkable property of these materials is their capacity to interact with a variety of chemical species, irrespective of their charge (neutral, cationic or anionic. These species can be grafted onto the surface of the layered materials or intercalated between the layers, to expand or contract the interlayer distance. Metalloporphyrins, which are typically soluble oxidation catalysts, are examples of molecules that can interact with layered materials. This work presents a short review of the studies involving metalloporphyrin immobilization on two different anionic exchangers, Layered Double Hydroxides (LDHs and Layered Hydroxide Salts (LHSs, published over the past year. After immobilization of anionic porphyrins, the resulting solids behave as reusable catalysts for heterogeneous oxidation processes. Although a large number of publications involving metalloporphyrin immobilization on LDHs exist, only a few papers have dealt with LHSs as supports, so metalloporphyrins immobilized on LHSs represent a new and promising research field. This work also describes new results on an anionic manganese porphyrin (MnP immobilized on Mg/Al-LDH solids with different nominal Mg/Al molar ratios (2:1, 3:1 and 4:1 and intercalated with different anions (CO32− or NO3−. The influence of the support composition on the MnP immobilization rates and the catalytic performance of the resulting solid in cyclooctene oxidation reactions will be reported.

  12. Recent Advances in Solid Catalysts Obtained by Metalloporphyrins Immobilization on Layered Anionic Exchangers: A Short Review and Some New Catalytic Results.

    Science.gov (United States)

    Nakagaki, Shirley; Mantovani, Karen Mary; Machado, Guilherme Sippel; Castro, Kelly Aparecida Dias de Freitas; Wypych, Fernando

    2016-01-01

    Layered materials are a very interesting class of compounds obtained by stacking of two-dimensional layers along the basal axis. A remarkable property of these materials is their capacity to interact with a variety of chemical species, irrespective of their charge (neutral, cationic or anionic). These species can be grafted onto the surface of the layered materials or intercalated between the layers, to expand or contract the interlayer distance. Metalloporphyrins, which are typically soluble oxidation catalysts, are examples of molecules that can interact with layered materials. This work presents a short review of the studies involving metalloporphyrin immobilization on two different anionic exchangers, Layered Double Hydroxides (LDHs) and Layered Hydroxide Salts (LHSs), published over the past year. After immobilization of anionic porphyrins, the resulting solids behave as reusable catalysts for heterogeneous oxidation processes. Although a large number of publications involving metalloporphyrin immobilization on LDHs exist, only a few papers have dealt with LHSs as supports, so metalloporphyrins immobilized on LHSs represent a new and promising research field. This work also describes new results on an anionic manganese porphyrin (MnP) immobilized on Mg/Al-LDH solids with different nominal Mg/Al molar ratios (2:1, 3:1 and 4:1) and intercalated with different anions (CO₃(2-) or NO₃(-)). The influence of the support composition on the MnP immobilization rates and the catalytic performance of the resulting solid in cyclooctene oxidation reactions will be reported. PMID:26938518

  13. Cleanup and analysis of sugar phosphates in biological extracts by using solid phase extraction and anion-exchange chromatography with pulsed amperometric detection

    DEFF Research Database (Denmark)

    Smith, Hans Peter; Cohen, A.; Buttler, T.;

    1998-01-01

    Saccharomyces cerevisiae obtained by using cold methanol as quenching agent and chloroform as extraction solvent. It was shown that pretreatment of the cell extract with SPE markedly improved the quality of the liquid chromatography analysis with recoveries of the sugar phosphates close to 100%. Furthermore......A cleanup method based on anion-exchange solid-phase extraction (SPE) was developed to render biological extracts suitable for the analysis of hexose phosphates with a modified anion-exchange chromatography method and pulsed amperometric detection. The method was applied to cell extracts of......, the method allowed for sample enrichment and the original extraction procedure could be simplified by implementing SPE early in the extraction protocol. (C) 1998 Academic Press....

  14. The development of sequential separation methods for the analysis of actinides in sediments and biological materials using anion-exchange resins and extraction chromatography

    International Nuclear Information System (INIS)

    New, quantitative methods for the determination of actinides have been developed for application to marine environmental samples (e.g., sediment and fish). The procedures include aggressive dissolution, separation by anion-exchange resin, separation and purification by extraction chromatography (e.g., TRU, TEVA and UTEVA resins) with measurement of the radionuclides by semiconductor alpha-spectrometry (SAS). Anion-exchange has proved to be a strong tool to treat large volume samples, and extraction chromatography shows an excellent selectivity and reduction of the amounts of acids. The results of the analysis of uranium, thorium, plutonium and americium isotopes by this method in marine samples (IAEA-384, -385 and -414) provided excellent agreement with the recommended values with good chemical recoveries. (author)

  15. Separation of 99TcO4- ions from actual reprocessing waste solution by poly (4-vinylpyridine-DVB) based anion exchangers

    International Nuclear Information System (INIS)

    Batch uptake of 99TcO4- ions from actual reprocessing waste solution was studied using three strong-base anion exchange resins prepared by quaternization of poly(4-vinylpyridine-DVB) with different alkyl (-CH3, -C2H5, and -n-C4H9) halides and two commercially available strong base anion exchange resins. Batch results showed that the resin with n-butyl group on the pyridine nitrogen has higher affinity for 99TcO4- ions. Excellent column performance of the resin for separation of 99TcO4- ions from such solution is established. Elution of 99TcO4- ions was carried out using 6 M HNO3 solution. (author)

  16. Heat resistance of the nuclear-quality hydroxide-form highly basic (type 1) anion exchange resin Varion AT-N

    International Nuclear Information System (INIS)

    The heat resistance of the Hungarian made nuclear-quality hydroxide-form highly basic (type 1) anion exchange resin Varion AT-N was studied under static conditions at temperatures 40 deg C, 60 deg C and 80 deg C. Subject to examinations was the deterioration of the resin grains as well as the change in capacity and replaceable chloride content as a function of the temperature and time. Conclusions in respect to the very slight changes in the resin were drawn from the analytical results of the aqueous extract. The results have shown that the deterioration of the anion exchange resin Varion AT-N(OH) is not significant even at 80 deg C. The magnitude of the calculated disintegration-rate constants agrees with the literature data. (author)

  17. Anion- or Cation-Exchange Membranes for NaBH4/H2O2 Fuel Cells?

    Directory of Open Access Journals (Sweden)

    César A. C. Sequeira

    2012-07-01

    Full Text Available Direct borohydride fuel cells (DBFC, which operate on sodium borohydride (NaBH4 as the fuel, and hydrogen peroxide (H2O2 as the oxidant, are receiving increasing attention. This is due to their promising use as power sources for space and underwater applications, where air is not available and gas storage poses obvious problems. One key factor to improve the performance of DBFCs concerns the type of separator used. Both anion- and cation-exchange membranes may be considered as potential separators for DBFC. In the present paper, the effect of the membrane type on the performance of laboratory NaBH4/H2O2 fuel cells using Pt electrodes is studied at room temperature. Two commercial ion-exchange membranes from Membranes International Inc., an anion-exchange membrane (AMI-7001S and a cation-exchange membrane (CMI-7000S, are tested as ionic separators for the DBFC. The membranes are compared directly by the observation and analysis of the corresponding DBFC’s performance. Cell polarization, power density, stability, and durability tests are used in the membranes’ evaluation. Energy densities and specific capacities are estimated. Most tests conducted, clearly indicate a superior performance of the cation-exchange membranes over the anion-exchange membrane. The two membranes are also compared with several other previously tested commercial membranes. For long term cell operation, these membranes seem to outperform the stability of the benchmark Nafion membranes but further studies are still required to improve their instantaneous power load.

  18. Solid-phase methods for sequencing of nucleic acids I. Simultaneous sequencing of different oligodeoxyribonucleotides using a new, mechanically stable anion-exchange paper.

    OpenAIRE

    Rosenthal, A.; Schwertner, S; Hahn, V; Hunger, H. D.

    1985-01-01

    A solid-phase method for simultaneous sequencing of large numbers of oligodeoxyribonucleotides has been developed using a new, mechanically stable anion-exchange paper. The excellent mechanical properties of the polymer allow the processing of several paper segments in one reaction vessel or to carry out all necessary operations on a larger area of the paper. In addition, DNA material can be chemically eluted from the new carrier during the piperidine reaction, thus avoiding salt elution of D...

  19. Sulfur geochemistry of hydrothermal waters in Yellowstone National Park, Wyoming, USA. III. An anion-exchange resin technique for sampling and preservation of sulfoxyanions in natural waters

    OpenAIRE

    Ball James W; Nordstrom D Kirk; Schoonen Martin AA; Druschel Greg K; Xu Yong; Cohn Corey A

    2003-01-01

    A sampling protocol for the retention, extraction, and analysis of sulfoxyanions in hydrothermal waters has been developed in the laboratory and tested at Yellowstone National Park and Green Lake, NY. Initial laboratory testing of the anion-exchange resin Bio-Rad™ AG1-X8 indicated that the resin was well suited for the sampling, preservation, and extraction of sulfate and thiosulfate. Synthetic solutions containing sulfate and thiosulfate were passed through AG1-X8 resin columns and eluted w...

  20. A simplified method for levoglucosan quantification in wintertime atmospheric particulate matter by high performance anion-exchange chromatography coupled with pulsed amperometric detection

    OpenAIRE

    Piazzalunga, A.; P. Fermo; Bernardoni, V.; VECCHI, R; Valli, G.; M. Gregorio

    2010-01-01

    Levoglucosan, a tracer for the assessment of the biomass burning contribution to atmospheric particulate matter (PM) concentrations, was determined by means of high-performance anion-exchange chromatography (HPAEC) with pulsed amperometric detection (PAD). In this work we propose a modification in the instrumental set-up aiming at an improvement in the detector response by adding NaOH after chromatographic separation to increase the pH. The comparison betwe...

  1. Characterization of Anion Exchange Membrane Containing Epoxy Ring and C–Cl Bond Quaternized by Various Amine Groups for Application in Fuel Cells

    OpenAIRE

    Sung Kuk Jeong; Ju Sung Lee; Sahng Hyuck Woo; Jin Ah Seo; Byoung Ryul Min

    2015-01-01

    Anion exchange membranes were synthesized from different compositions of glycidyl methacrylate (GMA) and vinylbenzyl chloride (VBC), with constant content of divinyl benzene (DVB) by radical polymerization using benzoyl peroxide (BPO) on non-woven polyethylene terephthalate (PET) substrate. Polymerized membranes were then quaternized by soaking in trimethylamine (TMA), triethylamine (TEA), tripropylamine (TPA), and 1,4-diazabicyclo [2.2.2] octane (DABCO). Characteristics of membranes were con...

  2. Characterization of Anion Exchange Membrane Containing Epoxy Ring and C–Cl Bond Quaternized by Various Amine Groups for Application in Fuel Cells

    OpenAIRE

    Sung Kuk Jeong; Ju Sung Lee; Sahng Hyuck Woo; Jin Ah Seo; Byoung Ryul Min

    2015-01-01

    Anion exchange membranes were synthesized from different compositions of glycidyl methacrylate (GMA) and vinylbenzyl chloride (VBC), with constant content of divinyl benzene (DVB) by radical polymerization using benzoyl peroxide (BPO) on non-woven polyethylene terephthalate (PET) substrate. Polymerized membranes were then quaternized by soaking in trimethylamine (TMA), triethylamine (TEA), tripropylamine (TPA), and 1,4-diazabicyclo [2.2.2] octane (DABCO). Characteristics of membranes were co...

  3. Structural and microstructural changes during anion exchange of CoAl layered double hydroxides: an in situ X-ray powder diffraction study

    DEFF Research Database (Denmark)

    Johnsen, Rune; Krumeich, Frank; Norby, Poul

    2010-01-01

    Anion-exchange processes in cobalt-aluminium layered double hydroxides (LDHs) were studied by in situ synchrotron X-ray powder diffraction (XRPD). The processes investigated were CoAl-CO3 CoAl-Cl CoAl-CO3, CoAl-Cl CoAl-NO3 and CoAl-CO3 CoAl-SO4. The XRPD data show that the CoAl-CO3 CoAl-Cl process...

  4. Differential inhibition of AE1 and AE2 anion exchangers by oxonol dyes and by novel polyaminosterol analogs of the shark antibiotic squalamine.

    Science.gov (United States)

    Alper, S L; Chernova, M N; Williams, J; Zasloff, M; Law, F Y; Knauf, P A

    1998-01-01

    Oxonol and polyaminosterol drugs were examined as inhibitors of recombinant mouse AE1 and AE2 anion exchangers expressed in Xenopus laevis oocytes and were compared as inhibitors of AE1-mediated anion flux in red cells and in HL-60 cells that express AE2. The oxonols WW-781, diBA(5)C4, and diBA(3)C4 inhibited HL-60 cell Cl-/Cl- exchange with IC50 values from 1 to 7 microM, 100-1000 times less potent than their IC50 values for red cell Cl-/anion exchange. In Xenopus oocytes, diBA(5)C4 inhibited AE1-mediated Cl- efflux several hundred times more potently than that mediated by AE2. Several novel squalamine-related polyaminosterols were also evaluated as anion exchange inhibitors. In contrast to diBA(5)C4, polyaminosterol 1361 inhibited oocyte-expressed AE2 8-fold more potently than AE1 (IC50 0.6 versus 5.2 microM). The 3-fold less potent desulfo-analog, 1360, showed similar preference for AE2. It was found that 1361 also partially inhibited Cl- efflux from red cells, whereas neither polyaminosterol inhibited Cl efflux from HL60 cells. Thus, the oxonol diBA(5)C4 is >100-fold more potent as an inhibitor of AE1 than of AE2, whereas the polyaminosterols 1360 and 1361 are 8-fold more potent as inhibitors of AE2 than of AE1. Assay conditions and cell type influenced IC50 values for both classes of compounds. PMID:10353714

  5. Determination of Amino Acids in Cell Culture and Fermentation Broth Media Using Anion-Exchange Chromatography with Integrated Pulsed Amperometric Detection

    OpenAIRE

    Hanko, Valoran P.; Heckenberg, Andrea; Rohrer, Jeffrey S.

    2004-01-01

    Anion-exchange chromatography with integrated pulsed amperometric detection (AE-IPAD) separates and directly detects amino acids, carbohydrates, alditols, and glycols in the same injection without pre- or post-column derivatization. These separations use a combination of NaOH and NaOH/sodium acetate eluents. We previously published the successful use of this technique, also known as AAA-Direct, to determine free amino acids in cell culture and fermentation broth media. We showed that retentio...

  6. Determination of chromium(VI) in water by PIXE analysis using ion exchange paper. Limit of detection and interference by coexisting anions

    International Nuclear Information System (INIS)

    Concerning the PIXE analysis of Cr(VI) in water using ion-exchange filters, the limit of detection (LOD) and the influence of matrix anions were investigated. In order to look for the experimental condition for obtaining the minimum LOD, we measured the Cr-Kα X-ray counts and background counts under the Kα X-ray peak as a function of the incident proton energy and the thickness of the Mylar absorber foil in front of the detector. To investigate the interference by coexisting anions, each of PO43-, SO42-, NO3-, Cl-, and F- ions and Cr(VI) ions were mixed in aqueous solutions and adsorbed on DE81-DEAE cellulose paper, a weakly basic anion exchanger with diethylaminoethyl functional groups. Then the filter samples were measured by PIXE using 2.5 MeV proton beams. We obtained a LOD of 0.16 μg or 8 ppb for 20 mL samples at a proton energy of 2.5 MeV and a Mylar film thickness of 50 or 100 μm. The experimental results on the mixed solutions indicated that NO3-, Cl-, and F- as coexisting ions didn't interfere significantly with determination of a 50 μg/L Cr(VI) concentration for 40 mL total solution volume, despite the total amount of anions was about 90% of ion exchange capacity of a filter. On the other hand, slight interferences by PO43- ions were observed. However, under the same condition, we found that if the total amount of SO42- ions was higher than 20% of ion exchange capacity, they induced significant interferences in determining Cr(VI). (author)

  7. Anion-exchange high-performance liquid chromatography with post-column detection for the analysis of phytic acid and other inositol phosphates

    Science.gov (United States)

    Rounds, M. A.; Nielsen, S. S.; Mitchell, C. A. (Principal Investigator)

    1993-01-01

    The use of gradient anion-exchange HPLC, with a simple post-column detection system, is described for the separation of myo-inositol phosphates, including "phytic acid" (myo-inositol hexaphosphate). Hexa-, penta-, tetra-, tri- and diphosphate members of this homologous series are clearly resolved within 30 min. This method should facilitate analysis and quantitation of "phytic acid" and other inositol phosphates in plant, food, and soil samples.

  8. Effect of alcohols on separation behavior of rare earth elements using benzimidazole-type anion-exchange resin in nitric acid solutions

    International Nuclear Information System (INIS)

    The mutual separation of rare earth elements based on the ion exchange chromatography has been studied. The effect of alcohols on separation behavior of rare earth elements using the benzimidazole-type anion-exchange resin embedded in high-porous silica beads was investigated in nitric acid/alcohol mixed solvent systems. It was confirmed that the mutual separation of rare earth elements is possible by using our proposed methods. It was found that the distribution coefficients of rare earth elements depend on the corresponding alcoholic relative permittivity and on the steric hindrance due to the hydrophobic interaction among each alcoholic molecule. (author)

  9. Stereo-dynamics of the exchange reaction Ha+LiHb→LiHa+Hb and its isotopic variants

    Institute of Scientific and Technical Information of China (English)

    Zhai Hong-Sheng; Yin Shu-Hui

    2012-01-01

    The quasi-classical trajectory (QCT) method is used to calculate the stereo-dynamics of the exchange reaction Ha+LiHb→LiHa+Hb and its isotopic variants based on an accurate potential energy surface reported by Prudente et al.[Prudente F V,Marques J M C and Maniero A M 2009 Chem.Phys.Lett.474 18].The reactive probability of the title reaction is computed.The vector correlations and four polarization-dependent generalized differential cross sections (PDDCSs) at different collision energies are presented.The influences of the collision energy and the reagent rotation on the product polarization are studied in the present work.The results indicate that the product rotational angular momentum j' is not only aligned,but also oriented along the direction perpendicular to the scattering plane.The product polarization distributions of the title reaction and its isotopic variants exhibit distinct differences which may arise from different mass combinations.

  10. Strong anion-exchange fast performance liquid chromatography as a versatile tool for preparation and purification of RNA produced by in vitro transcription.

    Science.gov (United States)

    Koubek, Jiri; Lin, Ku Feng; Chen, Yet Ran; Cheng, Richard Ping; Huang, Joseph Jen Tse

    2013-10-01

    Here we demonstrate the use of strong anion-exchange fast performance liquid chromatography (FPLC) as a simple, fast, and robust method for RNA production by in vitro transcription. With this technique, we have purified different transcription templates from unreacted reagents in large quantities. The same buffer system could be used to readily remove nuclease contamination from the overexpressed pyrophosphatase, the important reagent for in vitro transcription. In addition, the method can be used to monitor in vitro transcription reactions to enable facile optimization of reaction conditions, and we have compared the separation performance between strong and weak anion-exchange FPLC for various transcribed RNAs, including the Diels-Alder ribozyme, the hammerhead ribozyme tRNA, and 4.5S RNA. The functionality of the purified tRNA(Cys) has been confirmed by the aminoacylation assay. Only the purification by strong anion-exchange FPLC has led to the enrichment of the functional tRNA from run-off transcripts as revealed by both enzymatic and electrophoretic analysis. PMID:23929938

  11. Use of new tandem cation/anion exchange system with clinical-scale generators provides high specific volume solutions of technetium-99m and rhenium-188

    International Nuclear Information System (INIS)

    In this paper we describe the first application of our simple and inexpensive post-elution tandem cation/anion exchange column system which is based on generator elution with salts of weak acids such as ammonium acetate instead of saline solution to provide very high specific volume solutions of technetium-99m and rhenium-188 from clinical-scale molybdenum-99/technetium-99m generator prepared from low specific activity (n,y) molybdenum-99, and tungsten-188/rhenium-188 generators, respectively. Initial passage of the bolus through a strong cation exchange cartridge converts the ammonium acetate to acetic acid which is essentially not ionized at the acidic pH, allowing specific subsequent amine-type (QMA SepPak TM) anion exchange cartridge column trapping of the microscopic levels of the pertechnetate or perrhenate. Subsequent elution of the anion cartridge with a small volume (500 mCi/mL) from the alumina-based tungsten-188/rhenium-188 generator. (author)

  12. Hydrogen Exchange Mass Spectrometry of Related Proteins with Divergent Sequences: A Comparative Study of HIV-1 Nef Allelic Variants

    Science.gov (United States)

    Wales, Thomas E.; Poe, Jerrod A.; Emert-Sedlak, Lori; Morgan, Christopher R.; Smithgall, Thomas E.; Engen, John R.

    2016-03-01

    Hydrogen exchange mass spectrometry can be used to compare the conformation and dynamics of proteins that are similar in tertiary structure. If relative deuterium levels are measured, differences in sequence, deuterium forward- and back-exchange, peptide retention time, and protease digestion patterns all complicate the data analysis. We illustrate what can be learned from such data sets by analyzing five variants (Consensus G2E, SF2, NL4-3, ELI, and LTNP4) of the HIV-1 Nef protein, both alone and when bound to the human Hck SH3 domain. Regions with similar sequence could be compared between variants. Although much of the hydrogen exchange features were preserved across the five proteins, the kinetics of Nef binding to Hck SH3 were not the same. These observations may be related to biological function, particularly for ELI Nef where we also observed an impaired ability to downregulate CD4 surface presentation. The data illustrate some of the caveats that must be considered for comparison experiments and provide a framework for investigations of other protein relatives, families, and superfamilies with HX MS.

  13. Hydrogen Exchange Mass Spectrometry of Related Proteins with Divergent Sequences: A Comparative Study of HIV-1 Nef Allelic Variants

    Science.gov (United States)

    Wales, Thomas E.; Poe, Jerrod A.; Emert-Sedlak, Lori; Morgan, Christopher R.; Smithgall, Thomas E.; Engen, John R.

    2016-06-01

    Hydrogen exchange mass spectrometry can be used to compare the conformation and dynamics of proteins that are similar in tertiary structure. If relative deuterium levels are measured, differences in sequence, deuterium forward- and back-exchange, peptide retention time, and protease digestion patterns all complicate the data analysis. We illustrate what can be learned from such data sets by analyzing five variants (Consensus G2E, SF2, NL4-3, ELI, and LTNP4) of the HIV-1 Nef protein, both alone and when bound to the human Hck SH3 domain. Regions with similar sequence could be compared between variants. Although much of the hydrogen exchange features were preserved across the five proteins, the kinetics of Nef binding to Hck SH3 were not the same. These observations may be related to biological function, particularly for ELI Nef where we also observed an impaired ability to downregulate CD4 surface presentation. The data illustrate some of the caveats that must be considered for comparison experiments and provide a framework for investigations of other protein relatives, families, and superfamilies with HX MS.

  14. Hydrogen Exchange Mass Spectrometry of Related Proteins with Divergent Sequences: A Comparative Study of HIV-1 Nef Allelic Variants.

    Science.gov (United States)

    Wales, Thomas E; Poe, Jerrod A; Emert-Sedlak, Lori; Morgan, Christopher R; Smithgall, Thomas E; Engen, John R

    2016-06-01

    Hydrogen exchange mass spectrometry can be used to compare the conformation and dynamics of proteins that are similar in tertiary structure. If relative deuterium levels are measured, differences in sequence, deuterium forward- and back-exchange, peptide retention time, and protease digestion patterns all complicate the data analysis. We illustrate what can be learned from such data sets by analyzing five variants (Consensus G2E, SF2, NL4-3, ELI, and LTNP4) of the HIV-1 Nef protein, both alone and when bound to the human Hck SH3 domain. Regions with similar sequence could be compared between variants. Although much of the hydrogen exchange features were preserved across the five proteins, the kinetics of Nef binding to Hck SH3 were not the same. These observations may be related to biological function, particularly for ELI Nef where we also observed an impaired ability to downregulate CD4 surface presentation. The data illustrate some of the caveats that must be considered for comparison experiments and provide a framework for investigations of other protein relatives, families, and superfamilies with HX MS. Graphical Abstract ᅟ. PMID:27032648

  15. Chlorine isotope enrichment on a strong alkaline anion exchanger in dependence of type and concentration of the strange electrolytic solution

    International Nuclear Information System (INIS)

    Chlorine isotope enrichment for heterogenous ionexchange equilibria was studied. The dependence of element separation effects on the anion of the strange electrolyte (for same cation), on the cation of the strange electrolyte (for same anion), on the concentration of the strange electrolyte and also on the acetone: water ratio of the solvent was investigated. (orig./HBR)

  16. Anion exchange chromatography for the determination of 5-methyl-2'-deoxycytidine: application to cisplatin-sensitive and cisplatin-resistant ovarian cancer cell lines.

    Science.gov (United States)

    Iglesias, Tamara; Espina, Marta; Montes-Bayón, María; Sierra, Luisa María; Blanco-González, Elisa

    2015-03-01

    Epigenetic alterations are increasingly implicated in the initiation and progression of cancer. Genome-wide (global) hypomethylation seems to occur in early neoplasia and is a feature of genomic DNA derived from solid tumour tissues like ovarian cancer. Thus, analytical methods that provide sensitive and quantitative information about cytosine methylation in DNA are currently required. In this work, we compare two different anion-exchange columns for the separation of methylated cytosine from the other DNA nucleotides: a silica-based (Tracer Extrasil SAX) column and a polystyrene/divinyl benzene-based (Mono-Q™) column. Under the optimised conditions, linearity range, precision and detection limits of the developed high-performance liquid chromatography (HPLC) method were evaluated and compared using conventional ultraviolet (UV) absorbance detection at 270 nm. Good separation of the five target nucleotides, including 5-methyl-2'-deoxycytidine monophosphate (5mdCMP) and 2'-deoxycytidine monophosphate (dCMP) was achieved on the Mono-Q™ column with a gradient elution of ammonium acetate buffer (1 M, pH 6.9) at a flow rate of 1 mL min(-1). The coupling of this column to inductively coupled plasma mass spectrometry (ICP-MS) permitted also phosphorous ((31)P) specific detection of the nucleotides. Both detection systems offered adequate analytical performance characteristics, with detection limits of 30 and 40 μg L(-1) for 5mdCMP by HPLC-UV and HPLC-ICP-MS, respectively. However, the latter method allowed the determination of the global DNA methylation level (%) without the need for external calibration. Different genomic DNA samples were analysed including calf thymus DNA and DNA from two human cancer cell lines (adenocarcinoma epithelial A549 and ovarian carcinoma A2780) using the proposed strategy. In the line A2780, the cisplatin-sensitive and cisplatin-resistant variants were analysed, finding no significant differences in the methylation percentage after

  17. Removal of transmissible spongiform encephalopathy prion from large volumes of cell culture media supplemented with fetal bovine serum by using hollow fiber anion-exchange membrane chromatography.

    Directory of Open Access Journals (Sweden)

    Ming Li Chou

    Full Text Available Cases of variant Creutzfeldt-Jakob disease in people who had consumed contaminated meat products from cattle with bovine spongiform encephalopathy emphasize the need for measures aimed at preventing the transmission of the pathogenic prion protein (PrPSc from materials derived from cattle. Highly stringent scrutiny is required for fetal bovine serum (FBS, a growth-medium supplement used in the production of parenteral vaccines and therapeutic recombinant proteins and in the ex vivo expansion of stem cells for transplantation. One such approach is the implementation of manufacturing steps dedicated to removing PrPSc from materials containing FBS. We evaluated the use of the QyuSpeed D (QSD adsorbent hollow-fiber anion-exchange chromatographic column (Asahi Kasei Medical, Tokyo, Japan for the removal of PrPSc from cell culture media supplemented with FBS. We first established that QSD filtration had no adverse effect on the chemical composition of various types of culture media supplemented with 10% FBS or the growth and viability characteristics of human embryonic kidney (HEK293 cells, baby hamster kidney (BHK-21 cells, African green monkey kidney (Vero cells, and Chinese hamster ovary (CHO-k1 cells propagated in the various culture-medium filtrates. We used a 0.6-mL QSD column for removing PrPSc from up to 1000 mL of Dulbecco's modified Eagle's medium containing 10% FBS previously spiked with the 263K strain of hamster-adapted scrapie. The Western blot analysis, validated alongside an infectivity assay, revealed that the level of PrPSc in the initial 200mL flow-through was reduced by 2.5 to > 3 log10, compared with that of the starting material. These results indicate that QSD filtration removes PrPSc from cell culture media containing 10% FBS, and demonstrate the ease with which QSD filtration can be implemented in at industrial-scale to improve the safety of vaccines, therapeutic recombinant proteins, and ex vivo expanded stem cells produced

  18. Compensatory role of inducible annexin A2 for impaired biliary epithelial anion-exchange activity of inflammatory cholangiopathy.

    Science.gov (United States)

    Kido, Osamu; Fukushima, Koji; Ueno, Yoshiyuki; Inoue, Jun; Jefferson, Douglas M; Shimosegawa, Tooru

    2009-12-01

    The peribiliary inflammation of cholangiopathy affects the physiological properties of biliary epithelial cells (cholangiocyte), including bicarbonate-rich ductular secretion. We revealed the upregulation of annexin A2 (ANXA2) in cholangiocytes in primary biliary cirrhosis (PBC) by a proteomics approach and evaluated its physiological significance. Global protein expression profiles of a normal human cholangiocyte line (H69) in response to interferon-gamma (IFNgamma) were obtained by two-dimensional electrophoresis followed by MALDI-TOF-MS. Histological expression patterns of the identified molecules in PBC liver were confirmed by immunostaining. H69 cells stably transfected with doxycyclin-inducible ANXA2 were subjected to physiological evaluation. Recovery of the intracellular pH after acute alkalinization was measured consecutively by a pH indicator with a specific inhibitor of anion exchanger (AE), 4,4'-diisothiocyanatostilbene-2,2'-disulfonic acid (DIDS). Protein kinase-C (PKC) activation was measured by PepTag Assay and immunoblotting. Twenty spots that included ANXA2 were identified as IFNgamma-responsive molecules. Cholangiocytes of PBC liver were decorated by the unique membranous overexpression of ANXA2. Apical ANXA2 of small ducts of PBC was directly correlated with the clinical cholestatic markers and transaminases. Controlled induction of ANXA2 resulted in significant increase of the DIDS-inhibitory fraction of AE activity of H69, which was accompanied by modulation of PKC activity. We, therefore, identified ANXA2 as an IFNgamma-inducible gene in cholangiocytes that could serve as a potential histological marker of inflammatory cholangiopathy, including PBC. We conclude that inducible ANXA2 expression in cholangiocytes may play a compensatory role for the impaired AE activity of cholangiocytes in PBC in terms of bicarbonate-rich ductular secretion and bile formation through modulation of the PKC activity. PMID:19823170

  19. Size exclusion and anion exchange high performance liquid chromatography for characterizing metals bound to marine dissolved organic matter

    Energy Technology Data Exchange (ETDEWEB)

    Garcia-Otero, Natalia; Bermejo-Barrera, Pilar [Department of Analytical Chemistry, Nutrition and Bromatology, Faculty of Chemistry, University of Santiago de Compostela, Avenida das Ciencias, s/n, 15782 Santiago de Compostela (Spain); Moreda-Pineiro, Antonio, E-mail: antonio.moreda@usc.es [Department of Analytical Chemistry, Nutrition and Bromatology, Faculty of Chemistry, University of Santiago de Compostela, Avenida das Ciencias, s/n, 15782 Santiago de Compostela (Spain)

    2013-01-14

    Highlights: Black-Right-Pointing-Pointer Fractionation methods for assessing metals bound to marine DOM were developed. Black-Right-Pointing-Pointer SEC and AEC with UV detection and hyphenated with inductively coupled plasma-mass spectrometry were used. Black-Right-Pointing-Pointer SEC-UV showed marine DOM of molecular weights from 16 to 1 kDa. Black-Right-Pointing-Pointer Cobalt, manganese, strontium and zinc are bound to marine DOM. - Abstract: Size exclusion chromatography (SEC) followed by anion exchange chromatography (AEC) hyphenated with inductively coupled plasma-mass spectrometry (ICP-MS) was applied for fractionating metals bound to marine dissolved organic matter (DOM). Surface seawater samples (100 L) were subjected to tangential flow ultrafiltration (10,000 Da cut off) for isolating and pre-concentrating dissolved large molecules. The isolated fraction (retentate) consisted of 1 L, which was further freeze-dried and re-dissolved to 250 mL with ultrapure water. After HI Trap desalting of the re-dissolved retentate, SEC with UV detection showed marine DOM ranging from 6.5 kDa (lower than the permeable volume of the SEC column) to 16 kDa. A further characterization of this fraction by AEC with UV detection revealed the existence of four groups of macromolecules exhibiting retention times of 2.3, 2.8, 4.5 and 14.0 min. AEC hyphenated with ICP-MS showed the presence of strontium and zinc in the first AE fraction isolated from the SEC fraction; while manganese was found to be bound to the second AE fraction. Cobalt was found to be bound to molecules comprising the third AE fraction.

  20. Effect of dissolved organic matter on nitrate-nitrogen removal by anion exchange resin and kinetics studies

    Institute of Scientific and Technical Information of China (English)

    Haiou Song; Zhijian Yao; Mengqiao Wang; Jinnan Wang; Zhaolian Zhu; Aimin Li

    2013-01-01

    The effects of dissolved organic matter (DOM) on the removal of nitrate-nitrogen from the model contaminated water have been investigated utilizing the strong base anion exchange resins.With the increase of gallic acid concentration from 0 to 400 mg/L,the adsorption amount of nitrate-nitrogen on the commercial resins,including D201,Purolite A 300 (A300) and Purolite A 520E (A520E),would significantly decrease.However,the presence of tannin acid has little impact on nitrate-nitrogen adsorption on them.Compared to D201 and A300 resins,A520E resin exhibited more preferable adsorption ability toward nitrate-nitrogen in the presence of competing organic molecules,such as gallic acid and tannin acid at greater levels in aqueous solution.Attractively,the equilibrium data showed that the adsorption isotherm of nitrate-nitrogen on A520E resin was in good agreement with Langmuir and Freundlich equations.The rate parameters for the intra particle diffusion have been estimated for the different initial concentrations.In batch adsorption processes,nitrate-nitrogen diffuse in porous adsorbent and rate process usually depends on t1/2 rather than the contact time.The pseudo first-and the second-order kinetic models fit better for nitrate-nitrogen adsorption onto A520E resin.The observations reported herein illustrated that A520E resin will be an excellent adsorbent for enhanced removal of nitrate-nitrogen from contaminated groundwater.

  1. [Determination of fructooligosaccharides in milk powder using high performance anion-exchange chromatography coupled with pulsed amperometric detection].

    Science.gov (United States)

    Geng, Lijuan; Huang, Junrong; Feng, Feng; Jiang, Pingping; Chu, Xiaogang; Zhang, Feng; Ling, Yun

    2014-12-01

    Fructooligosaccharides (FOS) are usually added in milk powder as a kind of prebiotic. Thus, quantitative analysis of the FOS is very important for the quality control of milk powder. In this study, a simple method for the simultaneous determination of three FOS components with degrees of polymerization (DP) 3-5 in milk powder was developed by high performance anion-exchange chromatography coupled with pulsed amperometric detection (HPAEC-PAD). The samples were extracted with 50% (v/v) ethanol aqueous solution and defatted by an On Guard RP pretreatment column. The separation was performed on a CarboPac PA200 column by gradient elution using deionized water, 0. 2 mol/L NaOH solution and 0. 4 mol/L NaAc solution as the mobile phases. The flow rate was 0. 4 mL/min. The column temperature was 30 °C; and the injection volume was 25 µL. Good linear response was observed in the concentration range of 0.05-10 mg/L (r2 >0. 9993). The limits of quantification were 0. 02, 0. 005 and 0. 02 mg/L for 1-kestose, nystose and fructofuranosyl-nystose, respectively. The mean recoveries varied from 86. 0% to 114. 0% at three spiked levels of 0. 5, 1. 0 and 5. 0 mg/L. The short-chain fructooligosaccharides from inulooligosaccharides (IOS) were successfully separated by the developed HPAEC-PAD method. The method is simple, accurate, sensitive, and helpful for the quality control of milk powder. PMID:25902647

  2. Assessing gibberellins oxidase activity by anion exchange/hydrophobic polymer monolithic capillary liquid chromatography-mass spectrometry.

    Science.gov (United States)

    Chen, Ming-Luan; Su, Xin; Xiong, Wei; Liu, Jiu-Feng; Wu, Yan; Feng, Yu-Qi; Yuan, Bi-Feng

    2013-01-01

    Bioactive gibberellins (GAs) play a key regulatory role in plant growth and development. In the biosynthesis of GAs, GA3-oxidase catalyzes the final step to produce bioactive GAs. Thus, the evaluation of GA3-oxidase activity is critical for elucidating the regulation mechanism of plant growth controlled by GAs. However, assessing catalytic activity of endogenous GA3-oxidase remains challenging. In the current study, we developed a capillary liquid chromatography--mass spectrometry (cLC-MS) method for the sensitive assay of in-vitro recombinant or endogenous GA3-oxidase by analyzing the catalytic substrates and products of GA3-oxidase (GA1, GA4, GA9, GA20). An anion exchange/hydrophobic poly([2-(methacryloyloxy)ethyl]trimethylammonium-co-divinylbenzene-co-ethylene glycol dimethacrylate)(META-co-DVB-co-EDMA) monolithic column was successfully prepared for the separation of all target GAs. The limits of detection (LODs, Signal/Noise = 3) of GAs were in the range of 0.62-0.90 fmol. We determined the kinetic parameters (K m) of recombinant GA3-oxidase in Escherichia coli (E. coli) cell lysates, which is consistent with previous reports. Furthermore, by using isotope labeled substrates, we successfully evaluated the activity of endogenous GA3-oxidase that converts GA9 to GA4 in four types of plant samples, which is, to the best of our knowledge, the first report for the quantification of the activity of endogenous GA3-oxidase in plant. Taken together, the method developed here provides a good solution for the evaluation of endogenous GA3-oxidase activity in plant, which may promote the in-depth study of the growth regulation mechanism governed by GAs in plant physiology. PMID:23922762

  3. Assessing gibberellins oxidase activity by anion exchange/hydrophobic polymer monolithic capillary liquid chromatography-mass spectrometry.

    Directory of Open Access Journals (Sweden)

    Ming-Luan Chen

    Full Text Available Bioactive gibberellins (GAs play a key regulatory role in plant growth and development. In the biosynthesis of GAs, GA3-oxidase catalyzes the final step to produce bioactive GAs. Thus, the evaluation of GA3-oxidase activity is critical for elucidating the regulation mechanism of plant growth controlled by GAs. However, assessing catalytic activity of endogenous GA3-oxidase remains challenging. In the current study, we developed a capillary liquid chromatography--mass spectrometry (cLC-MS method for the sensitive assay of in-vitro recombinant or endogenous GA3-oxidase by analyzing the catalytic substrates and products of GA3-oxidase (GA1, GA4, GA9, GA20. An anion exchange/hydrophobic poly([2-(methacryloyloxyethyl]trimethylammonium-co-divinylbenzene-co-ethylene glycol dimethacrylate(META-co-DVB-co-EDMA monolithic column was successfully prepared for the separation of all target GAs. The limits of detection (LODs, Signal/Noise = 3 of GAs were in the range of 0.62-0.90 fmol. We determined the kinetic parameters (K m of recombinant GA3-oxidase in Escherichia coli (E. coli cell lysates, which is consistent with previous reports. Furthermore, by using isotope labeled substrates, we successfully evaluated the activity of endogenous GA3-oxidase that converts GA9 to GA4 in four types of plant samples, which is, to the best of our knowledge, the first report for the quantification of the activity of endogenous GA3-oxidase in plant. Taken together, the method developed here provides a good solution for the evaluation of endogenous GA3-oxidase activity in plant, which may promote the in-depth study of the growth regulation mechanism governed by GAs in plant physiology.

  4. Water quality monitoring system for determination of ionic nutrients by ion-exclusion chromatography with spectrophotometric detection on cationand anion-exchange resin columns using water eluent

    Institute of Scientific and Technical Information of China (English)

    Daisuke KOZAKI; Nobutakc NAKATANI; Masanobu MORI; Nobukazu NAKAGOSHI; Kazuhiko TANAKA

    2012-01-01

    A unified ion-exclusion chromatography(IEC)system for monitoring anionic and cationic nutrients like NH+4,NO-2,NO-3,phosphate ion,silicate ion and HCO-3 was developed and applied to several environmental waters.The IEC system consisted of four IEC methodologies,including the IEC with ultraviolet(UV)detection at 210 nm for determining NH-4 on anion-exchange separation column in OH form connected with anion-exchange UV-conversion column in I-form in tandem,the IEC with UV-detection at 210 nm for determining simultaneously NO-2 and NO-3 on cation-exchange separation column in H+ form,the IEC with UV-detection at 210 nm for determining HCO-3 on cation-exchange separation column in H+ form connected with anionexchange UV-conversion column in I-form in tandem,and the IEC with visible-detection based on molybdenum-blue reaction for determining simultaneously silicate and phosphate ions on cation-exchange separation column in H + form.These IEC systems were combined through three manually-driven 6-port column selection valves to select each separation column to determine selectively the ionic nutrients.Using this sequential water quality monitoring system,the analytical performances such as calibration linearity,reproducibility,detection limit and recovery were also tested under the optimized chromatographic conditions.This novel water quality monitoring system has been applied successfully for the determination of the ionic eutrophication components in sub-urban river waters.

  5. Sodium citrate-assisted anion exchange strategy for construction of Bi{sub 2}O{sub 2}CO{sub 3}/BiOI photocatalysts

    Energy Technology Data Exchange (ETDEWEB)

    Song, Peng-Yuan; Xu, Ming; Zhang, Wei-De, E-mail: zhangwd@scut.edu.cn

    2015-02-15

    Highlights: • Heterostructured Bi{sub 2}O{sub 2}CO{sub 3}/BiOI microspheres were prepared via anion exchange. • Sodium citrate-assisted anion exchange for construction of composite photocatalysts. • Bi{sub 2}O{sub 2}CO{sub 3}/BiOI composites show high visible light photocatalytic activity. - Abstract: Bi{sub 2}O{sub 2}CO{sub 3}/BiOI heterojuncted photocatalysts were constructed through a facile partial anion exchange strategy starting from BiOI microspheres and urea with the assistance of sodium citrate. The content of Bi{sub 2}O{sub 2}CO{sub 3} in the catalysts was regulated by modulating the amount of urea as a precursor, which was decomposed to generate CO{sub 3}{sup 2−} in the hydrothermal process. Citrate anion plays a key role in controlling the morphology and composition of the products. The Bi{sub 2}O{sub 2}CO{sub 3}/BiOI catalysts display much higher photocatalytic activity than pure BiOI and Bi{sub 2}O{sub 2}CO{sub 3} towards the degradation of rhodamine B (RhB) and bisphenol A (BPA). The enhancement of photocatalytic activity of the heterojuncted catalysts is attributed to the formation of p–n junction between p-BiOI and n-Bi{sub 2}O{sub 2}CO{sub 3}, which is favorable for retarding the recombination of photoinduced electron-hole pairs. Moreover, the holes are demonstrated to be the main active species for the degradation of RhB and BPA.

  6. Single vial sample preparation of markers of nerve agents by dispersive solid-phase extraction using magnetic strong anion exchange resins.

    Science.gov (United States)

    Singh, Varoon; Chinthakindi, Sridhar; Purohit, Ajay Kumar; Pardasani, Deepak; Tak, Vijay; Dubey, Devendra Kumar

    2015-05-22

    A sample preparation method involving extraction, enrichment and derivatization of acidic degradation products of nerve agents was developed using magnetic strong anion exchange resins (MSAX). The method was performed in a single vial involving magnetic dispersive solid phase extraction (MDSPE). Analytes were derivatized with N,O-bis(trimethylsilyl)trifluoroacetamide (BSTFA) in the presence of resins. MSAX were custom synthesized using Fe3O4 nanoparticles as core, 4-vinylpyridine-co-divinylbenzene as polymer shell and quaternary pyridinium function as anion-exchanger. Hydroxide ions were the counter-anions of MSAX to effectively capture the acidic alkyl alkylphosphonic acids (AAPAs) and alkylphosphonic acids (APAs). Quantitative measurements of analytes were performed in the selected ion monitoring mode of GC-MS. Full scan mode of analysis was followed for identifications. Under the optimized conditions analytes were recovered in the range of 39.7-98.8% (n=3, relative standard deviations (RSD) from 0.3 to 6.5%). Limits of detection (LODs) were in the range of 0.1-1.1ngmL(-1); and the linear dynamic range was 5-1000ngmL(-1) with r(2) of 0.9977-0.9769. Applicability of the method was tested with rain-, tap-, muddy-water and Organization for Prohibition of Chemical Weapons (OPCW) Proficiency Test samples. PMID:25863924

  7. Band 3, the human red cell chloride/bicarbonate anion exchanger (AE1, SLC4A1), in a structural context.

    Science.gov (United States)

    Reithmeier, Reinhart A F; Casey, Joseph R; Kalli, Antreas C; Sansom, Mark S P; Alguel, Yilmaz; Iwata, So

    2016-07-01

    The crystal structure of the dimeric membrane domain of human Band 3(1), the red cell chloride/bicarbonate anion exchanger 1 (AE1, SLC4A1), provides a structural context for over four decades of studies into this historic and important membrane glycoprotein. In this review, we highlight the key structural features responsible for anion binding and translocation and have integrated the following topological markers within the Band 3 structure: blood group antigens, N-glycosylation site, protease cleavage sites, inhibitor and chemical labeling sites, and the results of scanning cysteine and N-glycosylation mutagenesis. Locations of mutations linked to human disease, including those responsible for Southeast Asian ovalocytosis, hereditary stomatocytosis, hereditary spherocytosis, and distal renal tubular acidosis, provide molecular insights into their effect on Band 3 folding. Finally, molecular dynamics simulations of phosphatidylcholine self-assembled around Band 3 provide a view of this membrane protein within a lipid bilayer. PMID:27058983

  8. Long-term performance of bicarbonate-form anion exchange: removal of dissolved organic matter and bromide from the St. Johns River, FL, USA.

    Science.gov (United States)

    Walker, Krystal M; Boyer, Treavor H

    2011-04-01

    The goal of this research was to evaluate the long-term performance of magnetic ion exchange (MIEX) treatment using bicarbonate as the mobile counter ion (i.e., MIEX-HCO(3)) and sodium bicarbonate for regeneration. This work is important because there are many unknowns concerning the affinity and regeneration efficiency of bicarbonate-form anion exchange, whereas chloride-form anion exchange (i.e., MIEX-Cl resin) is well-studied. Raw water samples were collected approximately two times per month for one year from a single location on the St. Johns River (SJR), FL, USA. The SJR is characterized by high concentrations of dissolved organic carbon (DOC; 12-26 mg C/L) and bromide (550-1100 μg/L), and is being considered as an alternative drinking water supply. Jar tests were conducted using MIEX-HCO(3) resin, and MIEX-Cl resin was used as a baseline for comparison. The same batch of MIEX-HCO(3) and MIEX-Cl resin was used for the entire study, which was accomplished by regenerating the resins after each jar test in concentrated solutions of sodium bicarbonate and sodium chloride, respectively, and resulted in 21 regeneration cycles. Maximum removal efficiency was achieved with fresh MIEX-HCO(3) resin and virgin MIEX-Cl resin. Both forms of fresh/virgin MIEX resin also had the same affinity sequence with sulfate ≈ UV-absorbing substance > DOC > bromide. The removal efficiency of both forms of MIEX resin decreased as the number of regeneration cycles increased, with MIEX-HCO(3) resin showing 7-18% lower removals than MIEX-Cl resin after 21 regeneration cycles. The affinity sequence of regenerated MIEX-HCO(3) and MIEX-Cl resins differed from fresh resin with UV-absorbing substances > DOC > sulfate > bromide. Scanning electron microscopy and simulated MIEX-HCO(3) treatment under rapidly changing water quality were also used to improve the understanding of bicarbonate-form anion exchange. The major contribution of this research is a systematic study of the extended use of

  9. Anion exchange chromatographic distribution of human monoclonal immunoglobulin G is determined by heavy chain subclass and level of sialic acid expression

    Directory of Open Access Journals (Sweden)

    Ilić Vesna

    2012-01-01

    Full Text Available Anion exchange chromatography is widely accepted method for purification of immunoglobulins. In this work, we used human monoclonal immunoglobulin G (IgG with structure and solubility of normal human IgG as a model for studying chromatographic behavior of particular molecular forms of IgG. Human sera with monoclonal IgG were fractionated on strong anion exchanger, Q Sepharose Fast Flow. With 20 mM Tris pH 7.5 as a start buffer, 42% of human monoclonal IgG passed through column, and 58% of them remained adsorbed. Bound monoclonal IgG were eluted from the exchanger by linear increasing of concentration of NaCl from 0 to 0.5 M. Chromatographic distribution of human monoclonal IgG correlated with their electrophoretic mobility in agarose gels, and it was dependent on γ heavy chain isotype. Light chain type, as well as serum concentration of monoclonal IgG did not influence their chromatographic behavior. The level of heavy chain sialic acid expression, but not of galactose and N-acetylglucosamine, significantly determined chromatographic distribution of serum monoclonal IgG. Additionally to the information on the chromatographic behavior of human monoclonal IgG, we believe that presented data could provide useful information about the possible use of Q Sepharose Fast Flow matrix for the isolation of specific molecular forms of human IgG.

  10. Determination of antisense phosphorothioate oligonucleotides and catabolites in biological fluids and tissue extracts using anion-exchange high-performance liquid chromatography and capillary gel electrophoresis.

    Science.gov (United States)

    Chen, S H; Qian, M; Brennan, J M; Gallo, J M

    1997-04-25

    Chemically modified phosphorothioate oligodeoxynucleotides (ODNs) have become critical tools for research in the fields of gene expression and experimental therapeutics. Bioanalytical assays were developed that utilized fast anion-exchange high-performance liquid chromatography (HPLC) and capillary gel electrophoresis (CGE) for the determination of 20-mer ODNs in biological fluids (plasma and urine) and tissues. A 20 mer ODN in the antisense orientation directed against DNA methyltransferase (denoted as MT-AS) was studied as the model ODN. The anion-exchange HPLC method employed a short column packed with non-porous polymer support and a ternary gradient elution with 2 M lithium bromide containing 30% formamide. Analysis of the MT-AS is accomplished within 5 min with a detection limit of approximately 3 ng on-column at 267 nm. For plasma and urine, samples were diluted with Nonidet P-40 in 0.9% NaCl and directly injected onto the column, resulting in 100% recovery. For tissue homogenates, a protein kinase K digestion and phenol-chloroform extraction were used, with an average recovery of about 50%. Since the HPLC assay cannot provide one-base separation, biological samples were also processed by an anion-exchange solid-phase extraction and a CGE method to characterize MT-AS and its catabolites of 15-20-mer, species most relevant to biological activity. One base separation, under an electric field of 400 V/cm at room temperature, was achieved for a mixture of 15-20-mer with about 50 pg injected. Assay validation studies revealed that the combined HPLC-CGE methods are accurate, reproducible and specific for the determination of MT-AS and its catabolites in biological fluids and tissue homogenates, and can be used for the pharmacokinetic characterization of MT-AS. PMID:9187382

  11. Separation of rare earths from uranium by anion exchange with pre-exclusion of loading solution under pressure and determination by ICP-MS

    International Nuclear Information System (INIS)

    An intermittently pressurized anion exchange column is used for separation of trace rare earth elements (REES) from uranium before ICP-MS measurements. The whole separation can be completed within 20 min. The recoveries for all REES are in the range of 96%-106%. Comparing with previous methods, this technique consumes less chemicals and produces less waste. The applicability and reliability of this procedure is demonstrated by the good accordance between results determined by this method and the recommended values for REES in a standard reference material (GBW04207). It is proved that this method would be useful for analysis of trace REES impurities in uranium metal and its oxides

  12. Survey of inorganic arsenic in marine animals and marine certified reference materials by anion exchange high-performance liquid chromatography-inductively coupled plasma mass spectrometry

    DEFF Research Database (Denmark)

    Sloth, Jens Jørgen; Larsen, Erik Huusfeldt; Julshamn, Kåre

    2005-01-01

    A method for the determination of inorganic arsenic in seafood samples using high-performance liquid chromatography-inductively coupled plasma mass spectrometry is described. The principle of the method relied on microwave-assisted alkaline dissolution of the sample, which at the same time oxidized...... arsenite [As(Ill)] to arsenate [As(V)], whereby inorganic arsenic could be determined as the single species As(V). Anion exchange chromatography using isocratic elution with aqueous ammonium carbonate as the mobile phase was used for the separation of As(V) from other coextracted organoarsenic compounds...

  13. An enzymatic method for the determination of fructans in foods and food products - Comparison of the results by high performance anion exchange chromatography with pulsed amperemetric detection

    DEFF Research Database (Denmark)

    Andersen, Rikke; Sørensen, A.

    1999-01-01

    measurement of the released sugars enzymatically. Sucrose is hydrolysed by alpha-glucosidase instead of beta-fructosidase, which is normally used. In addition, sucrose is measured in the form of D-fructose instead of the typical D-glucose form, and the fructanase used to hydrolyse the fructans has fewer side...... effects than the fructanase reported as normally used. The method is tested on ten standard substances and five fructan products, and nine foods and food products are also analysed. The enzymatic measurement of the released sugars is confirmed by measurements done by high performance anion exchange...

  14. Complexation of uranyl ions. III. Investigation of the sorption of uranium of the VP-1Ap anion exchanger from carbonate media by x-ray spectrometric microanalysis

    International Nuclear Information System (INIS)

    The spatial distribution of uranium in granules of the VP-1Ap anion exchanger during heightened sorption from carbonate media has been investigated by x-ray spectroscopic microanalysis. Variation of the form of the concentration profile as a function of the extent of sorption from a uniform profile across the diameter, then to a meniscus-shaped profile, and finally to a smoothed profile with an increase in the coefficient of nonuniformity of the distribution of uranium in the granules from 0.026 to 0.045 has been established

  15. Separation of human milk oligosaccharides using high-performance anion-exchange chromatography with pulsed amperometric detection

    DEFF Research Database (Denmark)

    Lie, Aleksander; Pedersen, Lars Haastrup

    ) with pulsed amperometric detection (PAD) is an analysis method highly suited for carbohydrates. HPAE with alkaline eluents results in retention of neutral carbohydrates depending on the number of charged groups in the molecule, pH and concentration of competing anions, while PAD has sensitivity for...

  16. Improvement of separation efficiencies of anion-exchange chromatography using monolithic silica capillary columns modified with polyacrylates and polymethacrylates containing tertiary amino or quaternary ammonium groups.

    Science.gov (United States)

    Watanabe, Yuta; Ikegami, Tohru; Horie, Kanta; Hara, Takeshi; Jaafar, Jafariah; Tanaka, Nobuo

    2009-10-30

    Anion-exchange (AEX) columns were prepared by on-column polymerization of acrylates and methacrylates containing tertiary amino or quaternary ammonium groups on monolithic silica in a fused silica capillary modified with anchor groups. The columns provided a plate height (H) of less than 10 microm at optimum linear velocity (u) with keeping their high permeability (K=9-12 x 10(-14) m2). Among seven kinds of AEX columns, a monolithic silica column modified with poly(2-hydroxy-3-(4-methylpiperazin-1-yl)propyl methacrylates) (HMPMA) showed larger retentions and better selectivities for nucleotides and inorganic anions than the others. The HMPMA column of 410 mm length produced 42,000-55,000 theoretical plates (N) at a linear velocity of 0.97 mm/s with a backpressure of 3.8 MPa. The same column could be employed for a fast separation of inorganic anions in 1.8 min at a linear velocity of 5.3 mm/s with a backpressure of 20 MPa. In terms of van Deemter plot and separation impedance, the HMPMA column showed higher performance than a conventional particle-packed AEX column. The HMPMA column showed good recovery of a protein, trypsin inhibitor, and it was applied to the separation of proteins and tryptic digest of bovine serum albumin (BSA) in a gradient elution, to provide better separation compared to a conventional particle-packed AEX column. PMID:19683243

  17. Development of the ERIX process for reprocessing spent FBR-MOX fuel. Electrolytic reduction and anion exchange separation for U and FPs containing solution

    International Nuclear Information System (INIS)

    In recent years, we have been investigating the development of the ERIX process for reprocessing spent FBR-MOX fuel. The ERIX process uses electrolytic reduction and ion exchange techniques to recover U, Pu, Np and the minor actinides from spent EBR-MOX fuel solution. In previous work, it was found that U(VI) can be effectively reduced to U(IV) using the flow type electrolytic cell and U(IV) can be completely separated from fission products by AR-01 anion exchanger packed column in nitric acid medium. In the present work, electrolytic reduction behaviors of U(VI) and FPs containing solutions were investigated and the effects of various fission products, hydrazine, nitric acid and nitrous acid were examined. Furthermore, separation behavior of U from typical fission products in 6 mol/dm3 nitric acid solution after the electrolytic reduction were investigated using the column packed with AR-01. (author)

  18. Performance evaluation of anion exchange resins Purolite NRW-5050 and Duolite A-611 by application of radioisotopic techniques

    International Nuclear Information System (INIS)

    Radioanalytical techniques using 131I and 82Br as tracer isotopes were applied to study the kinetics of iodide and bromide ion-isotopic exchange reactions taking place between the external labeled ionic solution and the resin surface. The results indicate low values of specific reaction rate (min-1), amount of ion exchanged (mmol) and initial rate of ion exchange (mmol/min) for bromide ion-isotopic exchange reaction as compared to that obtained for iodide ion-isotopic exchange reaction. It was observed that for iodide ion-isotopic exchange reaction performed at 35.0 C, 1 000 g of ion exchange resins and 0.002 mol/L labeled iodide ion solution, the values of specific reaction rate (min-1), amount of iodide ion exchanged (mmol), initial rate of iodide ion exchange (mmol/min) and log Kd were 0.340, 0.394, 0.134 and 20.2 respectively for Purolite NRW-5050 resin, which was higher than the respective values of 0.216, 0.290, 0.063 and 18.2 as that obtained by using Duolite A-611. The results of present investigation indicate that during the two ion-isotopic exchange reactions, for both the resins, there exists a strong positive linear correlation between amount of ions exchanged and concentration of ionic solution; and strong negative correlation between amount of ions exchanged and temperature of exchanging medium. From the results it appears that as compared to Duolite A-611 resins, Purolite NRW-5050 resins shows superior performance under identical experimental conditions.

  19. Ion distribution in quaternary-ammonium-functionalized aromatic polymers: effects on the ionic clustering and conductivity of anion-exchange membranes.

    Science.gov (United States)

    Weiber, E Annika; Jannasch, Patric

    2014-09-01

    A series of copoly(arylene ether sulfone)s that have precisely two, three, or four quaternary ammonium (QA) groups clustered directly on single phenylene rings along the backbone are studied as anion-exchange membranes. The copolymers are synthesized by condensation polymerizations that involve either di-, tri-, or tetramethylhydroquinone followed by virtually complete benzylic bromination using N-bromosuccinimide and quaternization with trimethylamine. This synthetic strategy allows excellent control and systematic variation of the local density and distribution of QA groups along the backbone. Small-angle X-ray scattering of these copolymers shows extensive ionic clustering, promoted by an increasing density of QA on the single phenylene rings. At an ion-exchange capacity (IEC) of 2.1 meq g(-1), the water uptake decreases with the increasing local density of QA groups. Moreover, at moderate IECs at 20 °C, the Br(-) conductivity of the densely functionalized copolymers is higher than a corresponding randomly functionalized polymer, despite the significantly higher water uptake of the latter. Thus, the location of multiple cations on single aromatic rings in the polymers facilitates the formation of a distinct percolating hydrophilic phase domain with a high ionic concentration to promote efficient anion transport, despite probable limitations by reduced ion dissociation. These findings imply a viable strategy to improve the performance of alkaline membrane fuel cells. PMID:25044778

  20. Determination of uranium isotopes in urine samples from radiation workers using 232U tracer, anion-exchange resin and alpha-spectrometry

    International Nuclear Information System (INIS)

    Bioassay technique is used for the estimation of actinides present in the body based on the excretion rate of body fluids. For occupational radiation workers urine assay is the preferred method for monitoring of chronic internal exposure. Determination of low concentrations of actinides such as plutonium, americium and uranium at low level of mBq in urine by alpha-spectrometry requires pre-concentration of large volumes of urine. This paper deals with standardization of analytical method for the determination of U-isotopes in urine samples using anion-exchange resin and 232U tracer for radiochemical recovery. The method involves oxidation of urine followed by co-precipitation of uranium along with calcium phosphate. Separation of U was carried out by Amberlite, IRA-400, anion-exchange resin. U-fraction was electrodeposited and activity estimated using tracer recovery by alpha-spectrometer. Eight routine urine samples of radiation workers were analyzed and consistent radiochemical tracer recovery was obtained in the range of 51% to 67% with a mean and standard deviation of 60% and 5.4%, respectively. (author)

  1. Feasibility of wavelength dispersive X-ray fluorescence spectrometry for a simplified analysis of bromine in water samples with the aid of a strong anion exchange disk

    International Nuclear Information System (INIS)

    The feasibility of wavelength dispersive X-ray fluorescence spectrometry (WDXRF) for a simplified analysis of bromine (Br) in water samples with the aid of strong anion exchange (SAX) disk was assessed in this study. Dissolved Br in the water sample was pre-concentrated on the SAX disk and directly analyzed by WDXRF without an elution step. The SAX disk was capable of fully adsorbing both bromide (Br−) and bromate (BrO3−) on its surface owing to their anionic properties, regardless of the pH level of environmental samples. The SAX–WDXRF system was examined using calibration standards (i.e., SAX disks with specific amounts of Br retained; 1, 10, 50, 100 and 500 μg), and a determination coefficient of R2 = 0.9999 was yielded. The system had a low detection limit for Br (limit of detection = 0.253 μg for Br on the SAX disk) with good reproducibility (relative standard error (RSE) = 4–7%). Spike and inter-comparison tests were performed to confirm the accuracy of the proposed SAX–WDXRF method. Both tests exhibited reasonable accuracy (RSE = 3–6%). The method is simple and easy, indicating a great possibility of application in various environmental sample types, especially for which a simplified analytical system for the determination of Br is urgently required. - Highlights: • Bromide and bromate were entirely retained on a strong anion exchange (SAX) disk. • The SAX disk was used to pre-concentrate dissolved Br species from water samples. • The SAX disk adsorbing dissolved Br was directly analyzed by WDXRF. • The accuracy of the SAX–WDXRF method was confirmed by spike and inter-comparison tests. • Rapid and sensitive Br analysis can be achieved using the proposed SAX–WDXRF method

  2. Quality of 2-deoxy-2-[18F]fluoro-d-glucose injection prepared by isotopic exchange of fluorine using anion exchange or liquid phase exchange catalysed with amino polyether

    International Nuclear Information System (INIS)

    Production of 2-deoxy-2-[18F]fluoro-D-glucose ([18F]FDG) for Czech and Slovak PET Centres started on our upgraded U-120 cyclotron and in our radiopharmaceutical laboratory as early as June 1997, first for validation purposes and subsequently for clinical trials. The product was registered by the Czech State Institute for Drug Control in June 1999, and then distribution of the [18F]FDG injection preparation to hospitals was launched. The older automatic equipment (MicroLab I) manufactured by General Electric Medical Systems (GEMS) was based on a technology involving nucleophilic substitution of the precursor (1,3,4,6-tetra-O-acetyl-2-O-trifluoromethanesulfonyl-β-D-mannopyranose) dissolved in acetonitrile with [18F]fluoride absorbed on a solid anion exchanger modified with 4-(4-methylpiperidino) pyridine. This technology was used by us until March 2001, when it was superseded by a more advanced technology, MicroLab II. The nucleophilic substitution in the new technology is catalysed with amino polyether (Kryptofix) in a liquid phase. Benefits of MicroLab II include a significantly higher yield and better radiochemical purity of the product

  3. Quality of 2-deoxy-2-[18 F]fluoro-D-glucose injection prepared by isotopic exchange of fluorine using anion exchange or liquid phase exchange catalysed with aminopolyether

    International Nuclear Information System (INIS)

    Regular production of 2-deoxy-2-[18F]fluoro-D-glucose ([18F]FDG) for Czech and Slovak PET Centers started at our upgraded U-120 cyclotrone and radiopharmaceutical laboratory already in June 1997 when [18F]FDG started being produced for validation and then for clinical trials in the Czech Republic. After registering the product by the Czech State Institute for Drug Control in June 1999, distribution of [18F]FDG,injection, to hospitals was commenced. The older automatic equipment (MicroLab I) of General Electric Medical Systems (GEMS) used technology with nucleophilic substitution of precursor (1,3,4,6-tetra-O-acetyl-2-O-trifluormethansulfonyl-β-D-mannopyranose) dissolved in acetonitrile with [18F]fluoride absorbed on a solid anion exchanger modified with 4-(4-methylpiperidino) pyridine. We used this technology until March 2001, when it was substituted with more advanced technology, MicroLab II. Nucleophilic substitution in the new technology is catalysed with aminopolyether (Kryptofix) in a liquid phase. Benefits of the MicroLab II technology consist of significantly higher yield of synthesis and better radiochemical purity of the product. Those parameters for intermediate period in March 2001 when both technologies were used is presented, so the conditions for production were comparable. The MicroLab II technology brings much higher yield of synthesis while radiochemical purity of the product also increases to over 99%

  4. Extraction of Tetra-oxo Anions into a Hydrophobic, Ionic Liquid-Based Solvent Without Concomitant Ion Exchange

    International Nuclear Information System (INIS)

    Hydrophobic ionic liquids (IL) have the potential to simplify certain separations by serving as both an extraction solvent and an electrolyte for subsequent electrochemical reductions. While IL-based solvents are known to be efficient media for metal ion extraction, separations employing these solvents are frequently complicated by the loss of constituent IL ions to the aqueous phase, resulting in deteriorating performance. In this study, we have examined the extraction of pertechnetate and related tetra-oxo anions from aqueous solutions into IL-based solvents incorporating tetraalkylphosphonium bis((trifluoromethyl)sulfonyl)imide and a crown ether. In contrast to various previously studied IL-based cation extraction systems, facile anion extraction without significant transfer of the IL ions to the aqueous phase has been observed. In addition, the solvents exhibit high distribution ratios (100-500 for pertechnetate), significant electrical conductivity (>100 (micro)S/cm), and a wide (∼4 V) electrochemical window. The results suggest that these solvents may provide the basis for improved approaches to the extraction and recovery of a variety of anions.

  5. Synthesis and anion exchange reactions of a layered copper-zinc hydroxy double salt, Cu1×6Zn0×4(OH)3(OAc)×H2O

    Indian Academy of Sciences (India)

    Jacqueline Therese Rajamathi; Sylvia Britto; Michael Rajamathi

    2005-11-01

    A mixed-metal hydroxysalt of formula Cu1.6Zn0.4(OH)3(OAc)$\\cdot$H2O has been synthesized by an acetate hydrolysis route. Acetate ions can be exchanged with simple inorganic anions such as chloride and nitrate, and organic anions such as benzoate and large surfactant anions such as dodecyl sulphate. Structures of these hydroxysalts are derived from that of Cu2(OH)3NO3$\\cdot$H2O with some of the Cu2+ ions being replaced by Zn2+.

  6. Modeling and simulation of anion-exchange membrane chromatography for purification of Sf9 insect cell-derived virus-like particles.

    Science.gov (United States)

    Ladd Effio, Christopher; Hahn, Tobias; Seiler, Julia; Oelmeier, Stefan A; Asen, Iris; Silberer, Christine; Villain, Louis; Hubbuch, Jürgen

    2016-01-15

    Recombinant protein-based virus-like particles (VLPs) are steadily gaining in importance as innovative vaccines against cancer and infectious diseases. Multiple VLPs are currently evaluated in clinical phases requiring a straightforward and rational process design. To date, there is no generic platform process available for the purification of VLPs. In order to accelerate and simplify VLP downstream processing, there is a demand for novel development approaches, technologies, and purification tools. Membrane adsorbers have been identified as promising stationary phases for the processing of bionanoparticles due to their large pore sizes. In this work, we present the potential of two strategies for designing VLP processes following the basic tenet of 'quality by design': High-throughput experimentation and process modeling of an anion-exchange membrane capture step. Automated membrane screenings allowed the identification of optimal VLP binding conditions yielding a dynamic binding capacity of 5.7 mg/mL for human B19 parvovirus-like particles derived from Spodoptera frugiperda Sf9 insect cells. A mechanistic approach was implemented for radial ion-exchange membrane chromatography using the lumped-rate model and stoichiometric displacement model for the in silico optimization of a VLP capture step. For the first time, process modeling enabled the in silico design of a selective, robust and scalable process with minimal experimental effort for a complex VLP feedstock. The optimized anion-exchange membrane chromatography process resulted in a protein purity of 81.5%, a DNA clearance of 99.2%, and a VLP recovery of 59%. PMID:26718185

  7. Rapid simultaneous analysis of oxyhalides and inorganic anions in aqueous media by ion exchange chromatography with indirect UV detection

    Directory of Open Access Journals (Sweden)

    Mohammadine El Haddad

    2015-01-01

    Best separations have also occured between(Cl-/ClO3- and(Br-/BrO3- with good a resolution. Detections limits (S/N = 3 ofBrO3-,ClO3-andNO3- were 2 and 5 ppm for inorganic anions Cl−, Br− andSO42-. The method had a good linearity (r2 > 0.995 and high precision (relative standard deviation <4%. The main reason for the detector choice was that UV detectors are widespread in educational and low level equipment laboratories. Indirect photometric detection is an attractive and inexpensive approach and the system is versatile.

  8. Fixation and separation of the elements thorium and uranium using anion exchange resins in nitrate solution; Fixation et separation des elements thorium et uranium par les resines echangeuses d'anions en milieu nitrate

    Energy Technology Data Exchange (ETDEWEB)

    Korgaonkar, V. [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

    1967-10-01

    The exchange of thorium and uranium between a strong base anion resin and a mixed water + ethanol solvent containing nitrate ions is studied. It is assumed that in the resin the thorium and uranium are fixed in the form of the complexes Th(NO{sub 3}){sub 6}{sup 2-} and UO{sub 2}(NO{sub 3}){sub 4}{sup 2-} in solution these elements are present in the form of complexes having the general formula: Th(NO{sub 3}){sub 6-n}{sup n-2} and UO{sub 2}(NO{sub 3}){sub 4-n}{sup n-2} It has been possible to deduce a law for the changes in the partition functions of thorium and uranium as a function of the concentrations of the various species in solution and of the complexing ion NO{sub 3}. From this has been deduced the optimum operational conditions for separating a mixture of these two elements. Finally, in these conditions, the influence of a few interfering ions has been studied: Ba, Bi, Ce, La, Mo, Pb, Zr. The method proposed can be used either as a preparation, or for the dosage of thorium by a quantitative separation. (author) [French] On etudie l'echange du thorium et de l'uranium entre une resine anion base forte et un solvant mixte eau + ethanol charge en ions nitrates. On a suppose que, dans la resine, le thorium et l'uranium sont fixes sous forme de complexes Th(NO{sub 3}){sub 6}{sup 2-} et UO{sub 2}(NO{sub 3}){sub 4}{sup 2-} en solution, ces elements sont engages dans des complexes de formule generale: Th(NO{sub 3}){sub 6-n}{sup n-2} and UO{sub 2}(NO{sub 3}){sub 4-n}{sup n-2} On a pu degager une loi de variation des coefficients de partage du thorium et de l'uranium en fonction des concentrations des diverses especes en solution et de l'anion complexant NO{sub 3}{sup -}. On en a deduit les conditions operatoires optimales necessaires pour separer les deux elements a partir de leurs melanges. Enfin, dans ces conditions, on a etudie l'influence de quelques elements genants: Ba, Bi, Ce, La, Mo, Pb, Zr. La methode preconisee peut etre

  9. LAB-SCALE DEMONSTRATION OF PLUTONIUM PURIFICATION BY ANION EXCHANGE, PLUTONIUM (IV) OXALATE PRECIPITATION, AND CALCINATION TO PLUTONIUM OXIDE TO SUPPORT THE MOX FEED MISSION

    Energy Technology Data Exchange (ETDEWEB)

    Crowder, M.; Pierce, R.

    2012-08-22

    H-Canyon and HB-Line are tasked with the production of PuO{sub 2} from a feed of plutonium metal. The PuO{sub 2} will provide feed material for the MOX Fuel Fabrication Facility. After dissolution of the Pu metal in H-Canyon, the solution will be transferred to HB-Line for purification by anion exchange. Subsequent unit operations include Pu(IV) oxalate precipitation, filtration and calcination to form PuO{sub 2}. This report details the results from SRNL anion exchange, precipitation, filtration, calcination, and characterization tests, as requested by HB-Line1 and described in the task plan. This study involved an 80-g batch of Pu and employed test conditions prototypical of HB-Line conditions, wherever feasible. In addition, this study integrated lessons learned from earlier anion exchange and precipitation and calcination studies. H-Area Engineering selected direct strike Pu(IV) oxalate precipitation to produce a more dense PuO{sub 2} product than expected from Pu(III) oxalate precipitation. One benefit of the Pu(IV) approach is that it eliminates the need for reduction by ascorbic acid. The proposed HB-Line precipitation process involves a digestion time of 5 minutes after the time (44 min) required for oxalic acid addition. These were the conditions during HB-line production of neptunium oxide (NpO{sub 2}). In addition, a series of small Pu(IV) oxalate precipitation tests with different digestion times were conducted to better understand the effect of digestion time on particle size, filtration efficiency and other factors. To test the recommended process conditions, researchers performed two nearly-identical larger-scale precipitation and calcination tests. The calcined batches of PuO{sub 2} were characterized for density, specific surface area (SSA), particle size, moisture content, and impurities. Because the 3013 Standard requires that the calcination (or stabilization) process eliminate organics, characterization of PuO{sub 2} batches monitored the

  10. Isolation of radioactive strontium from natural samples. Separation of strontium from alkaline and alkaline earth elements by means of mixed solvent anion exchange

    International Nuclear Information System (INIS)

    This paper presents the results of studies which led to the procedures for the chromatographic separation of radioactive strontium from alkaline, earth-alkaline and other elements in natural samples, on columns filled with strong base anion exchangers using alcoholic solutions of nitric acid as eluents. It has been shown that potassium, caesium, calcium, barium, yttrium and strontium can be adsorbed on strong base anion exchangers of the Dowex and Amberlite type, which contain the quaternary ammonium group with nitrate as counter-ion, from solutions of nitric acid in alcohol. Adsorption strength increases in the order methanol 3 in methanol, while they are adsorbed from ethanol and propanol. The adsorption strength is influenced by the polarity of alcohol, by the concentration of nitrate and by pH. The strength with which strontium adsorbs on the exchangers increases in the interval from 0 to 0.25M NH4NO3 in methanol, after which it starts to decrease. Strontium adsorbs to the exchangers from the alcoholic solution of ammonium nitrate twice as strongly as from the alcoholic solution of nitric acid, while a fraction of water in pure alcohol exceeding 10% prevents adsorption. In the mixture of alcohol and nitric acid, the adsorption strength for calcium and strontium increases with the increase of the volume fraction of alcohol with a lower dielectric constant. The rate and strength of adsorption of ions on the exchanger also increase in the series 0.25M HNO3 in methanol 3 in ethanol 3 in 1-propanol for each individual ion, as well as in the Ca3 in methanol, 0.25M HNO3 in ethanol and 0.25M HNO3 in propanol. Separation is also possible from alcohol mixtures. Strontium separation is most difficult from calcium, while the efficiency of separation increases with a decrease of the polarity of the used alcohol or alcohol mixture. The first group elements of the periodic table are not separated from each other in this way, while the elements of the second group are

  11. Tens of micron-sized unilamellar nanosheets of Y/Eu layered rare-earth hydroxide: efficient exfoliation via fast anion exchange and their self-assembly into oriented oxide film with enhanced photoluminescence

    OpenAIRE

    Qi Zhu; Ji-Guang Li; Xiaodong Li; et al.

    2014-01-01

    Layered rare-earth hydroxide (LRH) crystals of (Y0.95Eu0.05)2(OH)5NO3centerdotnH2O with a lateral size of ~ 300 μm and a thickness of ~ 9 μm have been synthesized via a hydrothermal reaction of mixed nitrate solutions in the presence of mineralizer NH4NO3 at 200 °C for 24 h. LRH exhibits the ability to undergo intercalation and anion exchange with DS− (C12H25OSO3−) via hydrothermal treatment. Compared with traditional anion exchange at room temperature, hydrothermal processing not only shor...

  12. Kinetics of fast ligand exchange in excited lanthanide complexes with anions of salicylic and 5-sulfosalisylic acids

    International Nuclear Information System (INIS)

    The luminescent-kinetic spectroscopic method with a flash selective photoexcitation has been used for studying the reaction of ligand substitution with solvent molecules in complexes of electron-excited ions Tb3+(5D4) and Dysup(3+)(sup(4)Fsub(9/2) with anions of salicylic and 5-sulphosalicylic acids in water and methanol. The acidic-catalytic mechanism of this reaction in water has been established, the limiting stage of complex dissociation being the stage of proton addition to the -COO- group of the ligand proceeding at a rate of 1x1010 mol-1s-1 and 0.77x1010 mol-1xs-1 for complexes of Tb3+(5D4) in H2O and D2O. It has been shown that in an aqueous medium anions of salicylic and 5-sulphosalicylic acids behave with respect to r.e.e. ions as bidentate ligands coordinating these ions with the oxygen of the -COO- group and oxygroup whereas in methanol an additional coordination with oxygen of the oxygroup is absent

  13. Sorption behavior of perrhenate ion on ReillexTM-HP anion exchange resin from nitric acid and sodium nitrate/hydroxide solutions

    International Nuclear Information System (INIS)

    The distribution coefficients (K'd) are reported for perrhenate on the nitrate form of ReillexTM-HP, a weak base anion exchange resin, as a function of nitric acid concentration form 0.100 to 10.0 M. Perrhenate K'd values were determined in 1.00 M NaNO3 from pH 2 to 13. The K'd values were determined in solutions containing 1.35 M NaNO3 and variable NaOH, 0.155 to 4.66 M, and in solutions containing 0.655 M NaOH and variable NaNO3, 0.46 to 5.35M. Maximum perrhenate loadings were d is defined by the equation presented here. 30 refs., 4 figs., 1 tab

  14. Selective determination of ammonium ions by high-speed ion-exclusion chromatography on a weakly basic anion-exchange resin column.

    Science.gov (United States)

    Mori, Masanobu; Tanaka, Kazuhiko; Helaleh, Murad I H; Xu, Qun; Ikedo, Mikaru; Ogura, Yutaka; Sato, Shinji; Hu, Wenzhi; Hasebe, Kiyoshi

    2003-05-16

    This paper describes an ion-exclusion chromatographic system for the rapid and selective determination of ammonium ion. The optimized ion-exclusion chromatographic system was established with a polymethacrylate-based weakly basic anion-exchange resin column (TSKgel DEAE-5PW) as the separation column, an aqueous solution containing 0.05 mM tetramethylammonium hydroxide (pH 9.10) as eluent with conductimetric detection for the analyte determination. Under the optimum chromatographic conditions, ammonium ion was determined within 2.3 min with a detection limit (S/N=3) better than 0.125 microM. Ammonium ion in rain and river waters was precisely determined using this ion-exclusion chromatographic system. PMID:12830892

  15. Rapid isolation of plutonium in environmental solid samples using sequential injection anion exchange chromatography followed by detection with inductively coupled plasma mass spectrometry

    DEFF Research Database (Denmark)

    Qiao, Jixin; Hou, Xiaolin; Roos, Per;

    2011-01-01

    This paper reports an automated analytical method for rapid determination of plutonium isotopes (239Pu and 240Pu) in environmental solid extracts. Anion exchange chromatographic columns were incorporated in a sequential injection (SI) system to undertake the automated separation of plutonium from...... size effect upon the separation efficiency revealed that small-sized (2 mL) columns sufficed to handle up to 50 g of environmental soil samples. Under the optimum conditions, chemical yields of plutonium exceeded 90% and the decontamination factors for uranium, thorium and lead ranged from 103 to 104....... The determination of plutonium isotopes in three standard/certified reference materials (IAEA-375 soil, IAEA-135 sediment and NIST-4359 seaweed) and two reference samples (Irish Sea sediment and Danish soil) revealed a good agreement with reference/certified values. The SI column-separation method...

  16. Rapid determination of vitellogenin in fish plasma by anion exchange high performance liquid chromatography using postcolumn fluorescence derivatization with o-phthalaldehyde.

    Science.gov (United States)

    Wu, Cuiqin; Yuan, Dongxing; Liu, Baomin

    2006-12-01

    An analytical method involving anion exchange high performance liquid chromatographic determination of vitellogenin (Vtg) in fish plasma after postcolumn fluorescence derivatization with o-phthalaldehyde (OPA) was developed. The retention time of Vtg was about 11 min. The reagent variables for derivatization were optimized. The fluorophore was excited at 335 nm and detected at 435 nm. A calibration curve was established ranging from 0.13 to 11.28 microg. The determination limit of Vtg was found to be as low as 0.13 microg. The spiked recovery was 93.6% and interassay variability was less than 4%. The method developed was used to determine Vtg in fish plasma obtained from red sea bream (Pagrosomus major), black porgy (Sparus macrocephalus) and skew band grunt (Hapalogenys nitens), without complicated sample pretreatment. The results confirmed that the method showed advantages of being simple, rapid, reproducible and sensitive. PMID:17159322

  17. Optimization of SHINE Process: Design and Verification of Plant-Scale AG 1 Anion-Exchange Concentration Column and Titania Sorbent Pretreatment

    Energy Technology Data Exchange (ETDEWEB)

    Stepinski, Dominique C. [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Abdul, Momen [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Youker, Amanda J. [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Rotsch, David A. [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Tkac, Peter [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Chemerisov, Sergey [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Vandegrift, George F. [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division

    2016-06-01

    Argonne National Laboratory has developed a Mo-recovery and -purification system for the shine medical technologies process, which uses a uranyl sulfate solution for the accelerator-driven production of Mo-99. The objective of this effort is to reduce the processing time for the acidification of the Mo-99 product prior to loading onto a concentration column and concentration of the Mo-99 product solution. Two methods were investigated: (1) the replacement of the titania concentration column by an anion-exchange column to decrease processing time and increase the radioiodine-decontamination efficiency and (2) pretreatment of the titania sorbent to improve its effectiveness for the Mo-recovery and -concentration columns. Promising results are reported for both methods.

  18. Quantification of 1,5-anhydro-D-glucitol in urine by automated borate complex anion-exchange chromatography with an immobilized enzyme reactor.

    Science.gov (United States)

    Tanabe, T; Tajima, S; Suzuki, T; Okawa, E; Machida, R; Ichimura, S; Yabuuchi, M

    1997-04-25

    HPLC using a borate form of a strongly anion-exchange resin column and an immobilized enzyme reactor for colorimetric detection was used to quantify urinary 1,5-anhydro-D-glucitol. Urine samples were introduced into the system every 7 min without any pretreatment, and after separation of interfering substances in the column, 1,5-anhydro-D-glucitol was successively detected. Quantitative determination of urinary 1,5-anhydro-D-glucitol was possible within the 1.2-300 micromol/l range. The coefficient of variance was less than 3% and the correlation between results obtained with our system (y) and those obtained by gas chromatography-mass spectrometry (x) was y=0.983x-1.287 micromol/l (n=42, r=0.998). PMID:9187379

  19. Determination of Cr(VI) in welding fumes by anion-exchange fast protein liquid chromatography with electrothermal atomic absorption spectrometric detection.

    Science.gov (United States)

    Milacic, Radmila; Scancar, Janez; Tusek, Janez

    2002-02-01

    The applicability of an anion-exchange fast protein liquid chromatographic-electrothermal atomic absorption spectrometric procedure (FPLC-ETAAS) was investigated for the determination of Cr(VI) in welding fumes after alkaline extraction of aerosols loaded on filters. Gas tungsten arc welding (GTAW) of stainless steel was applied. Samples of welding fumes were collected during regular welding on polycarbonate membrane filters of 8 microm and 0.4 microm pore size (inhalable and respirable aerosols). Alkaline extraction (2% NaOH-3% Na2CO3) of filters in a heated ultrasonic bath was applied to leach Cr from the airborne particulate matter. 0.5 cm3 of sample extract was then injected onto an anion-exchange FPLC column. Tris-HCl buffer (0.005 mol dm(-3), pH 8.0) and the same buffer with NaCl (0.5 mol dm(-3)) were employed in gradient elution (15 min, flow rate 1 cm3 min(-1)). The separated Cr species were determined "off line" by ETAAS in 0.5 cm3 fractions. Cr(VI) was reproducibly and quantitatively eluted from 12.0 to 13.0 min with a maximum peak at 12.5 min. Good repeatability of measurement (+/-3.0%) of alkaline extracts was obtained for Cr(VI). The LOD (3s) was found to be 0.035 microg m(-3) Cr(VI), when 2 m3 of aerosols were collected on the filter. Validation of the procedure was performed by spiking alkaline extracts and by the analysis of standard reference material CRM 545, Cr(VI) in welding dust loaded on a filter. The technique was successfully applied for the determination of Cr(VI) in welding fumes. PMID:11939630

  20. In situ redox speciation analysis of chromium in water by diffusive gradients in thin films using a DE81 anion exchange membrane.

    Science.gov (United States)

    Suárez, Carlos A; de Simone, Thays V; Menegário, Amauri A; Rolisola, Ana M C M; Luko, Karen S; Gastmans, Didier; da Conceição, Fabiano T; Kiang, Chang H

    2016-07-01

    A method for the in situ redox speciation analysis of chromium in water by the diffusive gradients in thin films (DGT) technique using a DE81 anion exchange membrane was successfully developed. For the selective uptake of Cr(VI), a DGT device containing an anion exchange membrane DE81 (cellulose acetate chromatographic paper) was used (DE81-DGT), while selective uptake of Cr(III) was carried out using DGT devices containing the Chelex-100 resin (Chelex-100-DGT). A correlation coefficient of 0.993 was obtained for the linearity of the immersion curves (mass versus time) using DE81-DGT. The diffusion coefficient values for Cr(VI) through the agarose diffusive layer were equal to 4.89±0.5×10(-6)cm(2)s(-1) and 3.95±0.02×10(-6)cm(2)s(-1) (T=23±1°C, I=0.03molL(-1) NaNO3) were obtained by using diffusion cell and immersion curves, respectively. The retention of Cr(VI) by the DE81 membrane in a synthetic sample and river water was not affected by the pH over a wide range 4-9). Recoveries of Cr(VI) between 90% and 120% from solutions of ionic strength ranging from 0.01 to 0. 5molL(-1) NaNO3 were achieved. Finally, the redox speciation analysis of Cr(III) and Cr(VI) in spiked river water and synthetic samples was performed with recoveries greater than 80% and 87% by using Chelex-100-DGT and DE81-DGT devices, respectively. Those results were in excellent agreement with the diphenylcarbazide spectrophotometric method. PMID:27154678

  1. Sulfur geochemistry of hydrothermal waters in Yellowstone National Park, Wyoming, USA. III. An anion-exchange resin technique for sampling and preservation of sulfoxyanions in natural waters

    Directory of Open Access Journals (Sweden)

    Ball James W

    2003-06-01

    Full Text Available A sampling protocol for the retention, extraction, and analysis of sulfoxyanions in hydrothermal waters has been developed in the laboratory and tested at Yellowstone National Park and Green Lake, NY. Initial laboratory testing of the anion-exchange resin Bio-Rad™ AG1-X8 indicated that the resin was well suited for the sampling, preservation, and extraction of sulfate and thiosulfate. Synthetic solutions containing sulfate and thiosulfate were passed through AG1-X8 resin columns and eluted with 1 and 3 M KCl, respectively. Recovery ranged from 89 to 100%. Comparison of results for water samples collected from five pools in Yellowstone National Park between on-site IC analysis (U.S. Geological Survey mobile lab and IC analysis of resin-stored sample at SUNY-Stony Brook indicates 96 to 100% agreement for three pools (Cinder, Cistern, and an unnamed pool near Cistern and 76 and 63% agreement for two pools (Sulfur Dust and Frying Pan. Attempts to extract polythionates from the AG1-X8 resin were made using HCl solutions, but were unsuccessful. Bio-Rad™ AG2-X8, an anion-exchange resin with weaker binding sites than the AG1-X8 resin, is better suited for polythionate extraction. Sulfate and thiosulfate extraction with this resin has been accomplished with KCl solutions of 0.1 and 0.5 M, respectively. Trithionate and tetrathionate can be extracted with 4 M KCl. Higher polythionates can be extracted with 9 M hydrochloric acid. Polythionate concentrations can then be determined directly using ion chromatographic methods, and laboratory results indicate recovery of up to 90% for synthetic polythionate solutions using AG2-X8 resin columns.

  2. Selective separation of uranium using alizarin red S (ARS)-modified anion-exchange resin or by flotation of U-ARS chelate

    International Nuclear Information System (INIS)

    An alizarin red S (ARS)-modified anion exchange resin was prepared by a simple reaction of ARS with the anion exchange Doulite A101 and used for the efficient sorption of uranium from aqueous media. The effect of various parameters on the sorption of U(VI) (pH effect, sorption kinetics, resin capacity and breakthrough curves) was investigated. The modified resin sorbs U(VI) over a wide range of pH (2.8--5) with a maximum sorption capacity of 0.68 mmol/g at pH 3.2 to 4.0. Iron(III), Zr(IV), Ti(IV), Cu(II), and Th(IV) ions are also sorbed to different extents, but Be(II), Bi(III), Ca(II), Mg(II), Pb(II), Hg(II), Zn(II), Cd(II), Al(III), Mn(II), Co(II) and Ni(II) are not sorbed; thus, conditions for separating U(VI) from these metal ions have been identified. For eluting U(VI) from the resin, 0.2 mol/L HCl was used and the recovery recorded was as high as 99.9%. The use of ARS is extended to float uranium quantitatively and selectively from aqueous media at pH ∼ 4 by using oleic acid as a surfactant. The different parameters affecting the flotation process have also been investigated. Uranium(VI) has been effectively separated from natural water samples and certified uranium ores using both procedures

  3. Sulfur geochemistry of hydrothermal waters in Yellowstone National Park, Wyoming, USA. III. An anion-exchange resin technique for sampling and preservation of sulfoxyanions in natural waters

    Science.gov (United States)

    Druschel, Greg K; Schoonen, Martin AA; Nordstrom, D Kirk; Ball, James W; Xu, Yong; Cohn, Corey A

    2003-01-01

    A sampling protocol for the retention, extraction, and analysis of sulfoxyanions in hydrothermal waters has been developed in the laboratory and tested at Yellowstone National Park and Green Lake, NY. Initial laboratory testing of the anion-exchange resin Bio-Rad™ AG1-X8 indicated that the resin was well suited for the sampling, preservation, and extraction of sulfate and thiosulfate. Synthetic solutions containing sulfate and thiosulfate were passed through AG1-X8 resin columns and eluted with 1 and 3 M KCl, respectively. Recovery ranged from 89 to 100%. Comparison of results for water samples collected from five pools in Yellowstone National Park between on-site 1C analysis (U.S. Geological Survey mobile lab) and IC analysis of resin-stored sample at SUNY-Stony Brook indicates 96 to 100% agreement for three pools (Cinder, Cistern, and an unnamed pool near Cistern) and 76 and 63% agreement for two pools (Sulfur Dust and Frying Pan). Attempts to extract polythionates from the AG1-X8 resin were made using HCl solutions, but were unsuccessful. Bio-Rad™ AG2-X8, an anion-exchange resin with weaker binding sites than the AG1-X8 resin, is better suited for polythionate extraction. Sulfate and thiosulfate extraction with this resin has been accomplished with KCl solutions of 0.1 and 0.5 M, respectively. Trithionate and tetrathionate can be extracted with 4 M KCl. Higher polythionates can be extracted with 9 M hydrochloric acid. Polythionate concentrations can then be determined directly using ion chromatographic methods, and laboratory results indicate recovery of up to 90% for synthetic polythionate solutions using AG2-X8 resin columns.

  4. Rapid and simultaneous determination of neptunium and plutonium in environmental samples using anion exchange chromatographic and sequential injection setup combined with inductively coupled plasma mass spectrometry

    International Nuclear Information System (INIS)

    Full text: This paper presents an automated analytical method for the rapid and simultaneous determination of Pu and Np in the environmental samples. Anion exchange chromatographic column was incorporated in a sequential injection system to actualize the automated separation of Pu isotpes along with 237Np from the matrix elements and interfering radionuclides. K2S2O5-conc. HNO3 was applied as redox reagents for the valence adjustment and stabilization of Pu(IV) and Np(IV). 242Pu preformed well as a tracer for both Pu isotopes and 237Np. It was observed that the cross-link and particle size of the resins had significant effluence on the separation efficiency and anion exchange resin Bio-Rad AG 1 x 4 with the particle size of 100-200 mesh was chosen as the optimum. The investigation on the capacity showed small-sized column packed with 2mL resin sufficed up to 50g of soil sample, which provides an advantage of low consumption of the resin and low generation of acid waste after the column washing. The analytical results for Pu and Np in three reference materials showed good agreement with the certified or reference values at the 0.05 significance level. Chemical yields of Pu and Np equally range from 80% to 100%, and the decontamination factors for uranium, thorium and lead were in the range of 103 to 104. The total time of separation for a single sample was < 2.5 hours, which extremely improve the analysis efficiency and reduces the labor intensity, as well as enables a rapid determination of Pu and Np in emergency situations. (author)

  5. Automated flow-based anion-exchange method for high-throughput isolation and real-time monitoring of RuBisCO in plant extracts.

    Science.gov (United States)

    Suárez, Ruth; Miró, Manuel; Cerdà, Víctor; Perdomo, Juan Alejandro; Galmés, Jeroni

    2011-06-15

    In this work, a miniaturized, completely enclosed multisyringe-flow system is proposed for high-throughput purification of RuBisCO from Triticum aestivum extracts. The automated method capitalizes on the uptake of the target protein at 4°C onto Q-Sepharose Fast Flow strong anion-exchanger packed in a cylindrical microcolumn (105 × 4 mm) followed by a stepwise ionic-strength gradient elution (0-0.8 mol/L NaCl) to eliminate concomitant extract components and retrieve highly purified RuBisCO. The manifold is furnished downstream with a flow-through diode-array UV/vis spectrophotometer for real-time monitoring of the column effluent at the protein-specific wavelength of 280 nm to detect the elution of RuBisCO. Quantitation of RuBisCO and total soluble proteins in the eluate fractions were undertaken using polyacrylamide gel electrophoresis (PAGE) and the spectrophotometric Bradford assay, respectively. A comprehensive investigation of the effect of distinct concentration gradients on the isolation of RuBisCO and experimental conditions (namely, type of resin, column dimensions and mobile-phase flow rate) upon column capacity and analyte breakthrough was effected. The assembled set-up was aimed to critically ascertain the efficiency of preliminary batchwise pre-treatments of crude plant extracts (viz., polyethylenglycol (PEG) precipitation, ammonium sulphate precipitation and sucrose gradient centrifugation) in terms of RuBisCO purification and absolute recovery prior to automated anion-exchange column separation. Under the optimum physical and chemical conditions, the flow-through column system is able to admit crude plant extracts and gives rise to RuBisCO purification yields better than 75%, which might be increased up to 96 ± 9% with a prior PEG fractionation followed by sucrose gradient step. PMID:21641435

  6. Determination of trace amount of titanium in 2.5% Nb-Zr alloy by anion exchange separation and sulfo salicylic acid photometry

    International Nuclear Information System (INIS)

    A trace amount of Ti in 2.5% Nb-Zr alloy can be determined by a combined method of the characteristic anion exchange separation of Ti from Nb and the absorption photometry of Ti with sulfo salicylic acid. The alloy (1g) was dissolved in 5 ml of HF (1 + 1), and 5 ml of HNO3 was added to them. The resultant 5M HF - 6M HNO3 mixed acid solution was passed into an anion exchange resin column with 10 mm internal diameter and 100 mm high, at the rate of 1 to 2 ml/min. Niobium was adsorbed on to the column, through which Ti passed. The collected passing and washing solutions were converted into H2SO4 medium by twice successive fuming treatments. The solution was transferred into a volumetric flask of 50 ml, and 10 ml of 10% sulfo salicylic acid in H2SO4 was added. Diluting to a mark with H2SO4, the solution was allowed to stand for 15 min. Titanium was then determined by measuring absorption intensity at the wavelength of 410 mm. The influence of coexisting elements on the coloration of Ti and some adsorption conditions of Nb was experimentally investigated by using 95Nb as a tracer. The experiment revealed that the removal of Nb is essential, and that higher HF concentration and lower HNO3 concentration contribute to higher Nb adsorption. A variable rate type cockless column is useful for this routine analysis. The standard deviation and the coefficient of variation of analysis are 1.3 and 4.06% respectively for the concentration level of 32 ppm Ti (NZ-3). (Iwakiri, K.)

  7. Papaverine PVC Membrane Ion-Selective Electrodes Based on its Ion-Exchangers with Tetraphenylborate and Tetrathiocyanate Anions

    International Nuclear Information System (INIS)

    The construction and general performance of novel potentiometric membrane ion selective electrodes for determination of papaverine hydrochloride has been described. They are based on the formation of the ion association complexes of papaverine (PA) with tetraphenylborate (TPB)(1) or tetrathiocyanate (TTC)(2) counter anions as electro-active material dispersed in a PVC matrix. The electrodes show fast, stable, near Nernstian response for 1x10-2 to 6x10-5 M and 1x10-2 to 1x10-5 M for PA-TPB and PA-TTC respectively at 25 0C over the pH range of 3-5.0 with a cationic slope of ∼ 56.5±0.5 mV/decade for both sensors respectively. The lower detection limit is 4x10-5 and 8x10-6 M for PA-1 and PA-2 respectively with fast response time ranging from 20-45 sec. Selectivity coefficients for PA relative to a number of interfering substances were investigated. There is a negligible interference from the studied cations, anions, and pharmaceutical excipients. The determination of 4.0-3000.0 μg/ml of PA in aqueous solutions shows an average recovery of 99.1 % and a mean relative standard deviation of 1.4 at 100 μg/ml. The direct determination of PA in some formulations (Vasorin injection) gave results that compare favorably with those obtained using the British Pharmacopoeia method. Potentiometric titration of PA with sodium tetraphenylborate and potassium thiocyanate as titrants utilizing the papaverine electrode as an end point indicator electrode has been carried out

  8. Reorganization of Damaged Chromatin by the Exchange of Histone Variant H2A.Z-2

    Energy Technology Data Exchange (ETDEWEB)

    Nishibuchi, Ikuno [Department of Cellular Biology, Research Institute for Radiation Biology and Medicine, Hiroshima University, Hiroshima (Japan); Department of Radiation Oncology, Graduate School of Biomedical and Health Sciences, Hiroshima University, Hiroshima (Japan); Department of Radiation Oncology, Hiroshima Prefectural Hospital, Hiroshima (Japan); Suzuki, Hidekazu; Kinomura, Aiko; Sun, Jiying; Liu, Ning-Ang [Department of Cellular Biology, Research Institute for Radiation Biology and Medicine, Hiroshima University, Hiroshima (Japan); Horikoshi, Yasunori [Department of Cellular Biology, Research Institute for Radiation Biology and Medicine, Hiroshima University, Hiroshima (Japan); Research Center for Mathematics of Chromatin Live Dynamics, Hiroshima University, Hiroshima (Japan); Shima, Hiroki [Department of Biochemistry, Graduate School of Medical Sciences, Tohoku University, Sendai (Japan); Kusakabe, Masayuki; Harata, Masahiko [Laboratory of Molecular Biology, Graduate School of Agricultural Science, Tohoku University, Sendai (Japan); Fukagawa, Tatsuo [Department of Molecular Genetics, National Institute of Genetics and The Graduate University for Advanced Studies, Mishima (Japan); Ikura, Tsuyoshi [Laboratory of Chromatin Regulatory Network, Department of Mutagenesis, Radiation Biology Center, Kyoto University, Kyoto (Japan); Ishida, Takafumi [Department of Cardiovascular Medicine, Graduate School of Biomedical and Health Sciences, Hiroshima University, Hiroshima (Japan); Nagata, Yasushi [Department of Radiation Oncology, Graduate School of Biomedical and Health Sciences, Hiroshima University, Hiroshima (Japan); Tashiro, Satoshi, E-mail: ktashiro@hiroshima-u.ac.jp [Department of Cellular Biology, Research Institute for Radiation Biology and Medicine, Hiroshima University, Hiroshima (Japan); Research Center for Mathematics of Chromatin Live Dynamics, Hiroshima University, Hiroshima (Japan)

    2014-07-15

    Purpose: The reorganization of damaged chromatin plays an important role in the regulation of the DNA damage response. A recent study revealed the presence of 2 vertebrate H2A.Z isoforms, H2A.Z-1 and H2A.Z-2. However, the roles of the vertebrate H2A.Z isoforms are still unclear. Thus, in this study we examined the roles of the vertebrate H2A.Z isoforms in chromatin reorganization after the induction of DNA double-strand breaks (DSBs). Methods and Materials: To examine the dynamics of H2A.Z isoforms at damaged sites, we constructed GM0637 cells stably expressing each of the green fluorescent protein (GFP)-labeled H2A.Z isoforms, and performed fluorescence recovery after photobleaching (FRAP) analysis and inverted FRAP analysis in combination with microirradiation. Immunofluorescence staining using an anti-RAD51 antibody was performed to study the kinetics of RAD51 foci formation after 2-Gy irradiation of wild-type (WT), H2A.Z-1- and H2A.Z-2-deficient DT40 cells. Colony-forming assays were also performed to compare the survival rates of WT, H2A.Z-1-, and H2A.Z-2-deficient DT40 cells with control, and H2A.Z-1- and H2A.Z-2-depleted U2OS cells after irradiation. Results: FRAP analysis revealed that H2A.Z-2 was incorporated into damaged chromatin just after the induction of DSBs, whereas H2A.Z-1 remained essentially unchanged. Inverted FRAP analysis showed that H2A.Z-2 was released from damaged chromatin. These findings indicated that H2A.Z-2 was exchanged at DSB sites immediately after the induction of DSBs. RAD51 focus formation after ionizing irradiation was disturbed in H2A.Z-2-deficient DT40 cells but not in H2A.Z-1-deficient cells. The survival rate of H2A.Z-2-deficient cells after irradiation was lower than those of WT and H2A.Z-1- DT40 cells. Similar to DT40 cells, H2A.Z-2-depleted U2OS cells were also radiation-sensitive compared to control and H2A.Z-1-depleted cells. Conclusions: We found that vertebrate H2A.Z-2 is involved in the regulation of the DNA

  9. Reorganization of Damaged Chromatin by the Exchange of Histone Variant H2A.Z-2

    International Nuclear Information System (INIS)

    Purpose: The reorganization of damaged chromatin plays an important role in the regulation of the DNA damage response. A recent study revealed the presence of 2 vertebrate H2A.Z isoforms, H2A.Z-1 and H2A.Z-2. However, the roles of the vertebrate H2A.Z isoforms are still unclear. Thus, in this study we examined the roles of the vertebrate H2A.Z isoforms in chromatin reorganization after the induction of DNA double-strand breaks (DSBs). Methods and Materials: To examine the dynamics of H2A.Z isoforms at damaged sites, we constructed GM0637 cells stably expressing each of the green fluorescent protein (GFP)-labeled H2A.Z isoforms, and performed fluorescence recovery after photobleaching (FRAP) analysis and inverted FRAP analysis in combination with microirradiation. Immunofluorescence staining using an anti-RAD51 antibody was performed to study the kinetics of RAD51 foci formation after 2-Gy irradiation of wild-type (WT), H2A.Z-1- and H2A.Z-2-deficient DT40 cells. Colony-forming assays were also performed to compare the survival rates of WT, H2A.Z-1-, and H2A.Z-2-deficient DT40 cells with control, and H2A.Z-1- and H2A.Z-2-depleted U2OS cells after irradiation. Results: FRAP analysis revealed that H2A.Z-2 was incorporated into damaged chromatin just after the induction of DSBs, whereas H2A.Z-1 remained essentially unchanged. Inverted FRAP analysis showed that H2A.Z-2 was released from damaged chromatin. These findings indicated that H2A.Z-2 was exchanged at DSB sites immediately after the induction of DSBs. RAD51 focus formation after ionizing irradiation was disturbed in H2A.Z-2-deficient DT40 cells but not in H2A.Z-1-deficient cells. The survival rate of H2A.Z-2-deficient cells after irradiation was lower than those of WT and H2A.Z-1- DT40 cells. Similar to DT40 cells, H2A.Z-2-depleted U2OS cells were also radiation-sensitive compared to control and H2A.Z-1-depleted cells. Conclusions: We found that vertebrate H2A.Z-2 is involved in the regulation of the DNA

  10. Characterization of Anion Exchange Membrane Containing Epoxy Ring and C–Cl Bond Quaternized by Various Amine Groups for Application in Fuel Cells

    Directory of Open Access Journals (Sweden)

    Sung Kuk Jeong

    2015-07-01

    Full Text Available Anion exchange membranes were synthesized from different compositions of glycidyl methacrylate (GMA and vinylbenzyl chloride (VBC, with constant content of divinyl benzene (DVB by radical polymerization using benzoyl peroxide (BPO on non-woven polyethylene terephthalate (PET substrate. Polymerized membranes were then quaternized by soaking in trimethylamine (TMA, triethylamine (TEA, tripropylamine (TPA, and 1,4-diazabicyclo [2.2.2] octane (DABCO. Characteristics of membranes were confirmed by Fourier transform infrared spectroscopy, water uptake, ion exchange capacity, ion conductivity, thermal, and alkaline stability. The results revealed that membranes quaternized by TPA and DABCO showed high affinity when GMA content was 15 wt% and 75 wt%, respectively. IEC and ion conductivity of membranes quaternized by TPA were 1.34 meq·g−1 and 0.022 S·cm−1 (at 60 °C, respectively. IEC and ion conductivity of membranes were quaternized by DABCO were 1.34 meq·g−1 and 0.021 S·cm−1 (at 60 °C, respectively. The results indicate that the membrane containing GMA 15 wt% quaternized by TPA showed the highest thermal stability among membranes and exhibited high ion conductivity compared to existing researches using GMA, VBC, and DVB monomers.

  11. New inorganic (an)ion exchangers based on Mg–Al hydrous oxides: (Alkoxide-free) sol–gel synthesis and characterisation

    KAUST Repository

    Chubar, Natalia

    2011-05-01

    New inorganic ion exchangers based on double Mg-Al hydrous oxides were generated via the new non-traditional sol-gel synthesis method which avoids using metal alkoxides as raw materials. Surface chemical and adsorptive properties of the final products were controlled by several ways of hydrogels and xerogels treatments which produced the materials of the layered structure, mixed hydrous oxides or amorphous adsorbents. The final adsorptive materials obtained via thermal treatment of xerogels were the layered mesoporous materials with carbonate in the interlayer space, surface abundance with hydroxylic groups and maximum adsorptive capacity to arsenate. Higher affinity of Mg-Al hydrous oxides towards H2AsO4- is confirmed by steep adsorption isotherms having plateau (removal capacity) at 220. mg[As]. gdw-1 for the best sample at pH = 7, fast adsorption kinetics and little pH effect. Adsorption of arsenite, fluoride, bromate, bromide, selenate, borate by Mg-Al hydrous oxides was few times high either competitive (depending on the anion) as compare with the conventional inorganic ion exchange adsorbents. © 2011 Elsevier Inc.

  12. A Pd/C-CeO2 Anode Catalyst for High-Performance Platinum-Free Anion Exchange Membrane Fuel Cells.

    Science.gov (United States)

    Miller, Hamish A; Lavacchi, Alessandro; Vizza, Francesco; Marelli, Marcello; Di Benedetto, Francesco; D'Acapito, Francesco; Paska, Yair; Page, Miles; Dekel, Dario R

    2016-05-10

    One of the biggest obstacles to the dissemination of fuel cells is their cost, a large part of which is due to platinum (Pt) electrocatalysts. Complete removal of Pt is a difficult if not impossible task for proton exchange membrane fuel cells (PEM-FCs). The anion exchange membrane fuel cell (AEM-FC) has long been proposed as a solution as non-Pt metals may be employed. Despite this, few examples of Pt-free AEM-FCs have been demonstrated with modest power output. The main obstacle preventing the realization of a high power density Pt-free AEM-FC is sluggish hydrogen oxidation (HOR) kinetics of the anode catalyst. Here we describe a Pt-free AEM-FC that employs a mixed carbon-CeO2 supported palladium (Pd) anode catalyst that exhibits enhanced kinetics for the HOR. AEM-FC tests run on dry H2 and pure air show peak power densities of more than 500 mW cm(-2) . PMID:27062251

  13. Single particle electron microscopy analysis of the bovine anion exchanger 1 reveals a flexible linker connecting the cytoplasmic and membrane domains.

    Directory of Open Access Journals (Sweden)

    Jiansen Jiang

    Full Text Available Anion exchanger 1 (AE1 is the major erythrocyte membrane protein that mediates chloride/bicarbonate exchange across the erythrocyte membrane facilitating CO₂ transport by the blood, and anchors the plasma membrane to the spectrin-based cytoskeleton. This multi-protein cytoskeletal complex plays an important role in erythrocyte elasticity and membrane stability. An in-frame AE1 deletion of nine amino acids in the cytoplasmic domain in a proximity to the membrane domain results in a marked increase in membrane rigidity and ovalocytic red cells in the disease Southeast Asian Ovalocytosis (SAO. We hypothesized that AE1 has a flexible region connecting the cytoplasmic and membrane domains, which is partially deleted in SAO, thus causing the loss of erythrocyte elasticity. To explore this hypothesis, we developed a new non-denaturing method of AE1 purification from bovine erythrocyte membranes. A three-dimensional (3D structure of bovine AE1 at 2.4 nm resolution was obtained by negative staining electron microscopy, orthogonal tilt reconstruction and single particle analysis. The cytoplasmic and membrane domains are connected by two parallel linkers. Image classification demonstrated substantial flexibility in the linker region. We propose a mechanism whereby flexibility of the linker region plays a critical role in regulating red cell elasticity.

  14. Sequential injection analysis of lead using time-based colorimetric detection and preconcentration on an anionic-exchange resin.

    Science.gov (United States)

    Aracama, Nestor Zárate; Araújo, Alberto N; Perez-Olmos, Ricardo

    2004-04-01

    The development of a sequential injection analysis manifold for the colorimetric determination of lead in water samples is described The concentration of lead was assessed from its catalytic effect on the reaction of resazurine reduction caused by sulfide in an alkali medium. To that effect, the reaction zone was stopped at the detector, and the time interval required for the attainment of an absorbance decrease of 0.800 at the wavelength of 610 nm was estimated. Interference of other transition metals of the samples was minimized by adding potassium iodide to the sample and retaining the iodocomplexes formed in an on-line anionic resin (AGI X8). Elution was made with a 2 mol/L sodium hydroxide solution. The relationship [SIA] microg/L = 0.99 (+/- 0.11) x [ETAAS] microg/L + 0 (+/- 4) was obtained upon comparing the results given by the proposed system and by electrothermal atomization atomic absorption spectrometry (ETAAS) after the analysis of ten water samples. PMID:15116968

  15. Use of strong anion exchange resins for the removal of perfluoroalkylated substances from contaminated drinking water in batch and continuous pilot plants.

    Science.gov (United States)

    Zaggia, Alessandro; Conte, Lino; Falletti, Luigi; Fant, Massimo; Chiorboli, Andrea

    2016-03-15

    In recent years abnormally high levels of perfluoroalkylated substances (PFAS) have been detected both in surface and underground water sampled in an area covering approximately 150 square kilometers in the Veneto region (Italy) indicating the presence of a pollution point source (fluorochemicals production plant). Adsorption on granular activated carbon is an emergency measure which is poorly effective requiring frequent replacement. This work focuses on the application of three strong anion exchange resins (Purolite® A520E, A600E and A532E) for the removal of traces of PFOA, PFOS, PFBA and PFBS (concentration of hundreds of ng L(-1)) from drinking water. This technology is attractive for the possibility of reusing resins after an in-situ regeneration step. A strong relationship between the hydrophobicity of the exchange functional group of the resin and its capacity in removing PFAS exists. A600E (non hydrophobic) and A520E (fairly hydrophobic) show a reduced sorption capacity compared to A532E (highly hydrophobic). While A600E and A520E can be regenerated with solvent-less dilute solutions of non-toxic NH4Cl and NH4OH, A532E requires concentrated solutions of methanol or ethanol and 1% NH4Cl and for the sake of this work it was regarded as non-regenerable. The volume of regeneration effluents requiring incineration can be efficiently reduced by more than 96.5% by using reverse osmosis coupled with under-vacuum evaporation. Transmission electron analysis on saturated resins showed that large molecular macro-aggregates of PFAS can form in the intraparticle pores of resin indicating that ion exchange is not the only mechanism involved in PFAS removal. PMID:26774262

  16. Kinetics, stoichiometry, and anion selectivity of cAMP-stimulated Cl-HCO3 exchange in rabbit cortical collecting tubule (CCT)

    International Nuclear Information System (INIS)

    Cyclic AMP stimulates net HCO3 secretion in rabbit CCT (Schuster, JCI 75:2056). Because cAMP induces Cl-independent (electrogenic) HCO3 secretion in several epithelia, I studied the anion dependence of the CCT cAMP effect. Tubules were perfused in vitro with lumen amiloride; bath cAMP was continuously present to stimulate HCO3 secretion. First, the dependence of HCO3 secretion on lumen [Cl] was determined. With bath [Cl]=O mM, perfusate [Cl] was varied (2-150 mM, gluconate substitution). Mean lumen [Cl] was determined either by a silver electrode in the collected fluid (2-12 mM perfusate) or by 36Cl (12-150 mM). Total bath-to-lumen HCO3 flux, J/sup Ib//sub HCO3/, was measured (bath HCO3=25 mM, perfusate HCO3=O), Passive J/sub HCO3/ was estimated from the GHK equation using a previously-determined HCO3 permeability = 1.9 x 10-6 cm/s. Mediated J/sub HCO3/ vs. mean lumen [Cl] showed saturation kinetics, apparent K/sub m/ = 5.8 mM and V/sub max/ = 8.7 pmol/mm/min. Second, the stoichiometry was estimated. When bath HCO3 was replaced by HEPES at various perfusate [Cl] (12-150 mM), ΔJ/sub HCO3/ varied linearly with ΔJ/sup Ib/sub Cl/ (slope = .85 +- .27). Third, in anion selectivity studies Br supported HCO3 secretion (89% rate with Cl) but I- and SO4/sup =/ did not. In rabbit CCT, as opposed to several other HCO3-secreting epithelia, cAMP stimulates 1:1 Cl-HCO3 exchange

  17. Development and validation of an anion-exchange HPLC method for the determination of fluoride content and radiochemical purity in [18F]NaF

    International Nuclear Information System (INIS)

    18F-labeled sodium fluoride ([18F]NaF) is a useful bone imaging agent that has been demonstrated to be significantly more accurate than 99mTc-labeled methylene diphosphonate for the detection of both sclerotic and lytic lesions in various malignancies. A reliable anion-exchange HPLC method equipped with suppressed conductivity and radioactive detectors has been developed in order to analyze the content of NaF and radiochemical purity in [18F]NaF radiopharmaceuticals. The method described for fluoride analysis uses an isocratic elution of NaF in a Hamilton anion-exchange column using a mobile phase that consists of 7.5 mM sodium carbonate and 0.018 mM potassium thiocyanate. The flow rate was 1.0 ml/min. The method was validated in accordance with several parameters, including system suitability, specificity, precision, accuracy, linearity, robustness, limit of detection and limit of quantification. The results are described as follows: (1) The system suitability includes the tailing factor, theoretical plate number and resolution, which are 1.192534, 2729.6594 and 16.7415, respectively. (2) For specificity, the solvent peak and chloride ion did not interfere with the retention time of the fluoride. (3) The percentage coefficient of variation for analysis of precision, including repeatability and intermediate precision, is less than 2.0%. (4) Accuracy of method is within the range of 98%-102%. (5) The range of linearity is from 10 to 400 μg/ml, with the correlation coefficient (R2) always being above 0.9985. (6) The data of method robustness are within acceptance criteria. (7) The limit of detection and limit of quantification are 0.0678 and 0.20 μg/ml, respectively. All of the analysis results demonstrate that this method is highly sensitive, convenient, specific and suitable for quantification of NaF over a wide linear range. Therefore, the method can be successfully performed for routine analysis of fluoride content in [18F]NaF radiopharmaceuticals and reduce

  18. Treatment of Perchlorate-Contaminated Groundwater Using Highly-Selective, Regenerable Anion-Exchange Resins at Edwards Air Force Base

    Energy Technology Data Exchange (ETDEWEB)

    Gu, B.

    2003-05-30

    Selective ion exchange is one of the most effective treatment technologies for removing low levels of perchlorate (ClO{sub 4}{sup -}) from contaminated water because of its high efficiency without adverse impacts on the water quality caused by adding or removing any chemicals or nutrients. This report summarizes both the laboratory and a field pilot-scale studies to determine the ability and efficiency of the bifunctional synthetic resins to remove ClO{sub 4}{sup -} from the contaminated groundwater at the Edwards Air Force Base in California. Regeneration of the resins after groundwater treatment was also evaluated using the FeCl{sub 3}-HCl regeneration technique recently developed at Oak Ridge National Laboratory. On the basis of this study, the bifunctional resin, D-3696 was found to be highly selective toward ClO{sub 4}{sup -} and performed much better than one of the best commercial nitrate-selective resins (Purolite A-520E) and more than an order of magnitude better than the Purolite A-500 resin (with a relatively low selectivity). At an influent concentration of {approx} 450 {micro}g/L ClO{sub 4}{sup -} in groundwater, the bifunctional resin bed treated {approx} 40,000 empty bed volumes of groundwater before a significant breakthrough of ClO{sub 4}{sup -} occurred. The presence of relatively high concentrations of chloride and sulfate in site groundwater did not appear to affect the ability of the bifunctional resin to remove ClO{sub 4}{sup -}. However, the presence of high iron or iron oxyhydroxides and/or biomass in groundwater caused a significant fouling of the resin beds and greatly influenced the effectiveness in regenerating the resins sorbed with ClO{sub 4}{sup -}. Under such circumstances, a prefilter ({approx} 0.5-1 {micro}m) was found to be necessary to remove these particulates and to reduce the risk of fouling of the resin beds. Without significant fouling, the resin bed could be effectively regenerated by the FeCl{sub 3} displacement technique

  19. Multivariate analysis of the transport in an ion exchange membrane bioreactor for removal of anionic micropollutants from drinking water.

    Science.gov (United States)

    Ricardo, A R; Velizarov, S; Crespo, J G; Reis, M A M

    2011-01-01

    The present study focuses on investigating the effects of biological compartment conditions on the transport of nitrate and perchlorate in an Ion Exchange Membrane Bioreactor (IEMB). In this hybrid process, the transport depends not only on the membrane properties but also on the biological compartment conditions. The experiments were planned according to the Plackett-Burman statistical design in order to cover a broader range of experimental conditions, under which a previously developed mechanistic transport model was not able to predict correctly the transport fluxes of the target pollutants. Using Principal Component Analysis, it was possible to identify not only the concentrations of target (nitrate and perchlorate) and of major driving counter-ion (chloride) but also those of some biomedium components (e.g. ammonia, ethanol and sulphate) as variables that affect the transport rate of micropollutants across the membrane. These conclusions are based on the loadings of the two first principal components that describe 84% of the data variance. The present study also revealed that the hydraulic retention time and the hydrodynamic conditions in the biocompartment have a minor contribution to the micropollutants transport. The results obtained are important for process optimization purposes. PMID:21977639

  20. Cation Exchange Strategy for the Encapsulation of a Photoactive CO-Releasing Organometallic Molecule into Anionic Porous Frameworks.

    Science.gov (United States)

    Carmona, Francisco J; Rojas, Sara; Sánchez, Purificación; Jeremias, Hélia; Marques, Ana R; Romão, Carlos C; Choquesillo-Lazarte, Duane; Navarro, Jorge A R; Maldonado, Carmen R; Barea, Elisa

    2016-07-01

    The encapsulation of the photoactive, nontoxic, water-soluble, and air-stable cationic CORM [Mn(tacn)(CO)3]Br (tacn = 1,4,7-triazacyclononane) in different inorganic porous matrixes, namely, the metalorganic framework bio-MOF-1, (NH2(CH3)2)2[Zn8(adeninate)4(BPDC)6]·8DMF·11H2O (BPDC = 4,4'-biphenyldicarboxylate), and the functionalized mesoporous silicas MCM-41-SO3H and SBA-15-SO3H, is achieved by a cation exchange strategy. The CO release from these loaded materials, under simulated physiological conditions, is triggered by visible light. The results show that the silica matrixes, which are unaltered under physiological conditions, slow the kinetics of CO release, allowing a more controlled CO supply. In contrast, bio-MOF-1 instability leads to the complete leaching of the CORM. Nevertheless, the degradation of the MOF matrix gives rise to an enhanced CO release rate, which is related to the presence of free adenine in the solution. PMID:27291890

  1. Selenium speciation analysis in a sediment using strong anion exchange and reversed phase chromatography coupled with inductively coupled plasma-mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Ochsenkuehn-Petropoulou, M.; Michalke, B.; Kavouras, D.; Schramel, P

    2003-02-22

    An analytical procedure for selenium speciation of analysis of selenourea (SeU), selenoethionine (SeE), selenomethionine (SeM), Se(VI), Se(IV), dimethylselenide (dMeSe) and dimethyldiselenide (dMedSe) was developed, based on two complementary liquid chromatography (LC) techniques coupled with inductively coupled plasma-mass spectrometry (ICP-MS). Specifically, strong anion exchange (SAX) chromatography coupled with ICP-MS was used for the separation and quantification of all the earlier mentioned Se compounds, except for the two methyl selenides, which could be separated and determined by reversed phase chromatography coupled with ICP-MS. This procedure was applied to a soil sample from the warm springs area of Thermopyles (Greece). For leaching the Se species from the soil sample, four extraction methods, using water at ambient temperature, hot water, methanol and 0.5 M HCl, were tested for their efficiency of extracting the different Se species. The speciation results obtained by the LC-ICP-MS methods were compared with those obtained by voltammetric techniques. The determination of total selenium in the sample was achieved by graphite furnace atomic absorption spectrometry, as well as by ICP-atomic emission spectrometry, after suitable digestion of the sediment sample.

  2. Simple, selective, and rapid quantification of 1-deoxynojirimycin in mulberry leaf products by high-performance anion-exchange chromatography with pulsed amperometric detection.

    Science.gov (United States)

    Yoshihashi, Tadashi; Do, Huong Thi Thu; Tungtrakul, Patcharee; Boonbumrung, Sumitra; Yamaki, Kohji

    2010-04-01

    1-Deoxynojirimycin (DNJ) occurs in mulberry and other plants and is a highly potent glycosidase inhibitor reported to suppress blood glucose levels, thus preventing diabetes. Derivatization is required for quantification of DNJ upon use of spectral detection methods. Because of this difficulty, the DNJ contents of mulberry-based food products are rarely stated, even if DNJ is their active component. A simple, selective, and rapid method of high-performance anion-exchange chromatography with pulsed amperometric detection (HPAEC-PAD) to quantify DNJ in mulberry-based food products was developed. Stability testing of DNJ under heat treatment was also performed. A water extract of mulberry tea sample was subjected to HPAEC-PAD in a CarboPac MA1 column with a sodium hydroxide gradient. DNJ was clearly separated at a retention time of 7.26 min without interference and was selectively detected in the water extract. The detection limit was 5 ng. Heat stability studies suggested that DNJ was heat stable. HPAEC-PAD was not subject to interference, was highly selective for DNJ, and was superior to other high-performance liquid chromatography (HPLC) techniques in terms of sample preparation, resolution, and sensitivity. The method allowed simple, selective, and rapid analysis of DNJ in food matrices and might be useful for development of mulberry-based food products. Heat treatment could be an option for sterilizing mulberry-based products. PMID:20492274

  3. Durability and performance of polystyrene- b -poly(vinylbenzyl trimethylammonium) diblock copolymer and equivalent blend anion exchange membranes

    Energy Technology Data Exchange (ETDEWEB)

    Vandiver, Melissa A. [Department of Chemical and Biological Engineering, Colorado School of Mines, Golden Colorado 80401; Caire, Benjamin R. [Department of Chemical and Biological Engineering, Colorado School of Mines, Golden Colorado 80401; Poskin, Zach [Department of Chemical and Biological Engineering, Colorado School of Mines, Golden Colorado 80401; Li, Yifan [Department of Chemistry and Geochemistry, Colorado School of Mines, Golden Colorado 80401; Seifert, Sönke [X-Ray Science Division, Argonne National Laboratory, Argonne Illinois 60439; Knauss, Daniel M. [Department of Chemistry and Geochemistry, Colorado School of Mines, Golden Colorado 80401; Herring, Andrew M. [Department of Chemical and Biological Engineering, Colorado School of Mines, Golden Colorado 80401; Liberatore, Matthew W. [Department of Chemical and Biological Engineering, Colorado School of Mines, Golden Colorado 80401

    2014-11-01

    Anion exchange membranes (AEM) are solid polymer electrolytes that facilitate ion transport in fuel cells. In this study, a polystyrene-b-poly(vinylbenzyl trimethylammonium) diblock copolymer was evaluated as potential AEM and compared with the equivalent homopolymer blend. The diblock had a 92% conversion of reactive sites with an IEC of 1.72 ± 0.05 mmol g-1, while the blend had a 43% conversion for an IEC of 0.80 ± 0.03 mmol g-1. At 50°C and 95% relative humidity, the chloride conductivity of the diblock was higher, 24–33 mS cm-1, compared with the blend, 1–6 mS cm-1. The diblock displayed phase separation on the length scale of 100 nm, while the blend displayed microphase separation (~10 μm). Mechanical characterization of films from 40 to 90 microns thick found that elasticity and elongation decreased with the addition of cations to the films. At humidified conditions, water acted as a plasticizer to increase film elasticity and elongation. While the polystyrene-based diblock displayed sufficient ionic conductivity, the films' mechanical properties require improvement, i.e., greater elasticity and strength, before use in fuel cells. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 41596.

  4. Rapid and sensitive quantification of levoglucosan in aerosols by high-performance anion-exchange chromatography with positive electrospray ionization mass spectrometry (HPAEC-positive ESI-MS)

    Science.gov (United States)

    Asakawa, Daichi; Furuichi, Yuko; Yamamoto, Atsushi; Oku, Yuichiro; Funasaka, Kunihiro

    2015-12-01

    A convenient quantification method for underivatized levoglucosan, which is a tracer for biomass burning influenced particulate matter (PM), has been established using high-performance anion-exchange chromatography (HPAEC) coupled to positive electrospray ionization mass spectrometry ((+)ESI-MS). Levoglucosan was chromatographically separated from its isomers (mannosan and galactosan) and detected selectively with positive ESI-MS. Limits of detection and quantification for this method were 0.40 and 1.3 ng mL-1, respectively. A comparison of simultaneous measurements by this method and conventional derivatization gas chromatography/mass spectrometry showed a good linearity with a slope of 1.008 and a determination coefficient of 0.9932. The developed method was applied to ambient suspended particulate matter hourly collected by continuous particulate monitors at 10 stations. The hourly concentration of levoglucosan during August 9-11, 2011, was 1.7-918 ng m-3 and its distribution indicated the transportation of biomass burning aerosols of a forest fire. This is the first report of horizontal distribution of the hourly levoglucosan concentration in Japan.

  5. Analytical Method for Sugar Profile in Pet Food and Animal Feeds by High-Performance Anion-Exchange Chromatography with Pulsed Amperometric Detection.

    Science.gov (United States)

    Ellingson, David J; Anderson, Phillip; Berg, Daniel P

    2016-03-01

    There is a need for a standardized, accurate, rugged, and consistent method to measure for sugars in pet foods and animal feeds. Many traditional standard sugar methods exist for other matrixes, but when applied in collaborative studies there was poor agreement and sources of error identified with those standard methods. The advancement in technology over the years has given us the ability to improve on these standard methods of analysis. A method is described here that addresses these common issues and was subjected to a single-laboratory validation to assess performance on a wide variety of pet foods and animal feeds. Of key importance to the method performance is the sample preparation before extraction, type of extraction solvent, postextraction cleanup, and, finally, optimized chromatography using high-performance anion exchange chromatography with pulsed amperometric detection. The results obtained from the validation demonstrate how typical issues seen with these matrixes can influence performance of sugar analysis. The results also demonstrate that this method is fit-for-purpose and can meet the challenges of sugar analysis in pet food and animal feeds to lay the foundation for a standardized method of analysis. PMID:26952902

  6. Short-column anion-exchange chromatography for soil and peat humic substances profiling by step-wise gradient of high pH aqueous sodium ethylenediaminetetraacetate.

    Science.gov (United States)

    Hutta, Milan; Ráczová, Janka; Góra, Róbert; Pessl, Juraj

    2015-08-21

    Novel anion-exchange liquid chromatographic method with step gradient of aqueous EDTA(4-) based mobile phase elution has been developed to profile available Slovak soil humic substances and alkaline extracts of various soils. The method utilize short glass column (30mm×3mm) filled in with hydrolytically stable particles (60μm diameter) Separon HEMA-BIO 1000 having (diethylamino)ethyl functional groups. Step gradient was programmed by mixing mobile phase composed of aqueous solution of sodium EDTA (pH 12.0; 5mmolL(-1)) and mobile phase constituted of aqueous solution of sodium EDTA (pH 12.0, 500mmolL(-1)). The FLD of HSs was set to excitation wavelength 480nm and emission wavelength 530nm (λem). Separation mechanism was studied by use of selected aromatic acids related to humic acids with the aid of UV spectrophotometric detection at 280nm. The proposed method benefits from high ionic strength (I=5molL(-1)) of the end mobile phase buffer and provides high recovery of humic acids (98%). Accurate and reproducible profiling of studied humic substances, alkaline extracts of various types of soils enables straightforward characterization and differentiation of HSs in arable and forest soils. Selected model aromatic acids were used for separation mechanism elucidation. PMID:26143606

  7. The determination of adsorption capacity of anion exchange resin Dowex-Marathon for Ti(IV) and Fe(III) chlorocomplexes

    International Nuclear Information System (INIS)

    Full text: The adsorption capacity of anion exchange resin Dowex-Marathon for Ti(IV) and Fe(III) chlorocomplexes from HCl solution was determined. The measurements were performed for different HCl solution concentrations and temperatures using batch operation as contact method between solution and resin. The Fe(III) adsorption capacities increased with HCl solution concentrations and contact temperatures. In the case of Ti(IV) considerable adsorption capacities were observed only at HCl concentrations >7 M. For the same ion the adsorption capacity does not depend on temperature in the range of 30 - 70 deg C. At 50 deg C there is an important difference between adsorption capacity for Fe(III), (105.7 mg Fe/g dry resin) and for U(VI), (227 mg U/g dry resin), allowing the recovery of uranium adsorption band in the 235U enriching column, using band displacement technique. A solution of TiCl3 0.1 M in HCl >7 M can be utilized as reduction agent at the rear edge of the uranium band, according to the important adsorption capacity of Ti(IV) in those conditions. (author)

  8. Preparation and characterization of anion exchange resin decorated with magnetite nanoparticles for removal of p-toluic acid from aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Davarpanah, Morteza, E-mail: Davarpanah.morteza@gmail.com; Ahmadpour, Ali; Rohani Bastami, Tahereh

    2015-02-01

    Polystyrene resin was covalently functionalized with diethanolamine and then decorated with magnetite nanoparticles by a novel and simple co-precipitation method using iron(II) sulfate as precursor. The products were characterized by Fourier transform infrared spectroscopy, elemental analysis, X-ray diffraction, Mössbauer spectroscopy, field-emission scanning electron microscopy and vibrating sample magnetometer. Adsorption of p-toluic acid (p-TA) onto magnetite-decorated polystyrene (MAG-PS) was studied and compared with that of diethanolamine-functionalized polystyrene and a commercial anion exchange resin. Results showed that the magnetite nanoparticles with an average size of 20.4 nm were successfully formed on the surface of polystyrene resin, and MAG-PS was exhibited high affinity for the removal of p-TA. - Highlights: • .Polystyrene resin was covalently functionalized with diethanolamine. • .The functionalized adsorbents were decorated with magnetite nanoparticles (∼20 nm). • .Proposed magnetization procedure was high-efficient and relatively simple. • .Magnetic adsorbent was presented high affinity for removal of p-toluic acid.

  9. Dextrin characterization by high-performance anion-exchange chromatography--pulsed amperometric detection and size-exclusion chromatography--multi-angle light scattering--refractive index detection.

    Science.gov (United States)

    White, D Richard; Hudson, Patricia; Adamson, Julie T

    2003-05-16

    Starch hydrolysis products, or dextrins, are widely used throughout the food industry for their functional properties. Dextrins are saccharide polymers linked primarily by alpha-(1 --> 4) D-glucose units and are prepared by partial hydrolysis of starch. Hydrolysis can be accomplished by the use of acid, enzymes, or by a combination of both. The hydrolysis products are typically characterized by the "dextrose equivalent" (DE), which refers to the total reducing power of all sugars present relative to glucose. While the DE gives the supplier and buyer a rough guide to the bulk properties of the material, the physiochemical properties of dextrins are dependent on the overall oligosaccharide profile. High-performance anion-exchange chromatography (HPAEC) with pulsed amperometric detection and size-exclusion chromatography (SEC) with multi-angle light-scattering and refractive index detection were used to characterize dextrins from commercial sources. HPAEC was used to acquire the oligosaccharide profile, and SEC to obtain an overall molar mass distribution. These methods in combination extended our understanding of the relationship between oligosaccharide profile, DE, and the hydrolysis process. Data from the two techniques enabled a method for estimating the DE that gave results in reasonable agreement with the accepted titration method. PMID:12830879

  10. Using an Anion Exchange Membrane to Predict Soil Available N and S Supplies and the Impact of N and S Fertilization on Canola and Wheat Growth

    Institute of Scientific and Technical Information of China (English)

    P. QIAN; J. J. SCHOENAU

    2007-01-01

    A growth chamber study was conducted to determine the relationships between the supply of soil available nitrogen (N) and sulfur (S) and canola (Brassica napus) and wheat (Triticum aestivum L. 'Biggar') N and S uptake and yield in three Western Canadian soils. The suitability of one-hour burial with an anion exchange membrane (AEM) was assessed for its utility as a quick test of the available N:S balance in the soil. Canola and wheat were grown on a Luvisolic soil low in available S and on Brown and Black Chernozemic soils low in both available N and S, with different rates and combinations of N and S fertilizers applied. AEM burial was used to assess soil available nitrate and sulfate supply rates after fertilization. Dry matter yield and N and S concentrations in plant tissues were determined after 6 weeks of growth.The soil available N:S ratio determined by AEM burial closely reflected the relative supplies of available N and S as revealed in the N:S ratios of plant tissue dry matter. The highest yields were achieved where the available N:S ratio in soil and plant tissue ranged from 5 to 13. Thus, a one-hour burial of an AEM probe in the field may be a useful tool to quickly test if a balanced N and S supply is present in the soil for optimum crop yield.

  11. Advanced treatment of textile dyeing secondary effluent using magnetic anion exchange resin and its effect on organic fouling in subsequent RO membrane.

    Science.gov (United States)

    Yang, Cheng; Li, Li; Shi, Jialu; Long, Chao; Li, Aimin

    2015-03-01

    Strict regulations are forcing dyeing factory to upgrade existing waste treatment system. In this study, advanced treatment of dyeing secondary effluent by magnetic anion exchange resin (NDMP) was investigated and compared with ultrafiltration (UF); NDMP as a pre-treatment of reverse osmosis (RO) was also studied. NDMP resin (20 mL/L) gave higher removal of dissolved organic carbon (DOC) (83.9%) and colority (94.9%) than UF with a cut-off of 10 kDa (only 48.6% and 44.1%, respectively), showing that NDMP treatment was effective to meet the stringent discharge limit of DOC and colority. Besides, NDMP resin (20 mL/L) as a pretreatment of RO increased the permeate flux by 12.5% and reduced irreversible membrane fouling by 6.6%, but UF pretreatment did not mitigate RO membrane fouling. The results of excitation-emission matrix fluorescence spectra and resin fractions showed that NDMP had more efficient removal than UF for transphilic acid and hydrophilic fraction, such as protein-like organic matters and soluble microbial products, which contributed to a significant proportion of RO membrane fouling. In sum, NDMP resin treatment not only gave effective removal of DOC and colority of dyeing secondary effluent, but exhibited some improvement for RO membrane flux and irreversible fouling. PMID:25463217

  12. Radioimmunoassay of a new angiotensin-converting enzyme inhibitor (perindopril) in human plasma and urine: Advantages of coupling anion-exchange column chromatography with radioimmunoassay

    Energy Technology Data Exchange (ETDEWEB)

    Doucet, L.; De Veyrac, B.; Delaage, M.; Cailla, H.; Bernheim, C.; Devissaguet, M. (Immunotech S. A. Case 915, Marseille (France))

    1990-08-01

    Perindopril (P) is a prodrug whose active metabolite perindoprilat (PT) is an antihypertensive agent which acts by inhibition of angiotensin-converting enzyme (ACE). Anti-PT antiserum was produced in a rabbit immunized against PT that was covalently linked to bovine serum albumin. The radioligand is an iodinated ({sup 125}I) derivative of PT-glycyltyrosinamide. Both the drug (PT) and the prodrug (P) are assayed in the same sample; PT is assayed as is and P is assayed after quantitative alkaline hydrolysis into PT. Certain data obtained from such assays suggest the occurrence in plasma and urine of a third immunoreactive component. A chromatographic fractionation of samples allowed us to isolate a new immunoreactive metabolite which was further identified as a glucuronide of PT (PT-G). Therefore, the whole assay was carried out as follows: biological samples were fractionated by stepwise chromatography on a anion-exchange resin (the first fraction contained P, the second contained PT, and the third contained PT-G); and RIA was performed on fractions 2 and 3 as is, and on fraction 1 after alkaline hydrolysis. Performances and assessments of this method are presented together with an example of a pharmacokinetic profile.

  13. Preparation and characterization of anion exchange resin decorated with magnetite nanoparticles for removal of p-toluic acid from aqueous solution

    International Nuclear Information System (INIS)

    Polystyrene resin was covalently functionalized with diethanolamine and then decorated with magnetite nanoparticles by a novel and simple co-precipitation method using iron(II) sulfate as precursor. The products were characterized by Fourier transform infrared spectroscopy, elemental analysis, X-ray diffraction, Mössbauer spectroscopy, field-emission scanning electron microscopy and vibrating sample magnetometer. Adsorption of p-toluic acid (p-TA) onto magnetite-decorated polystyrene (MAG-PS) was studied and compared with that of diethanolamine-functionalized polystyrene and a commercial anion exchange resin. Results showed that the magnetite nanoparticles with an average size of 20.4 nm were successfully formed on the surface of polystyrene resin, and MAG-PS was exhibited high affinity for the removal of p-TA. - Highlights: • .Polystyrene resin was covalently functionalized with diethanolamine. • .The functionalized adsorbents were decorated with magnetite nanoparticles (∼20 nm). • .Proposed magnetization procedure was high-efficient and relatively simple. • .Magnetic adsorbent was presented high affinity for removal of p-toluic acid

  14. Human kidney anion exchanger 1 interacts with adaptor-related protein complex 1 {mu}1A (AP-1 mu1A)

    Energy Technology Data Exchange (ETDEWEB)

    Sawasdee, Nunghathai; Junking, Mutita [Division of Medical Molecular Biology and BIOTEC-Medical Biotechnology Unit, Department of Research and Development, Faculty of Medicine Siriraj Hospital, Mahidol University, Bangkok 10700 (Thailand); Ngaojanlar, Piengpaga [Division of Medical Molecular Biology and BIOTEC-Medical Biotechnology Unit, Department of Research and Development, Faculty of Medicine Siriraj Hospital, Mahidol University, Bangkok 10700 (Thailand); Department of Immunology and Graduate Program in Immunology, Faculty of Medicine Siriraj Hospital, Mahidol University, Bangkok 10700 (Thailand); Sukomon, Nattakan; Ungsupravate, Duangporn [Division of Medical Molecular Biology and BIOTEC-Medical Biotechnology Unit, Department of Research and Development, Faculty of Medicine Siriraj Hospital, Mahidol University, Bangkok 10700 (Thailand); Limjindaporn, Thawornchai [Division of Medical Molecular Biology and BIOTEC-Medical Biotechnology Unit, Department of Research and Development, Faculty of Medicine Siriraj Hospital, Mahidol University, Bangkok 10700 (Thailand); Department of Anatomy, Faculty of Medicine Siriraj Hospital, Mahidol University, Bangkok 10700 (Thailand); Akkarapatumwong, Varaporn [Institute of Molecular Biosciences, Mahidol University at Salaya Campus, Nakorn Pathom 73170 (Thailand); Noisakran, Sansanee [Division of Medical Molecular Biology and BIOTEC-Medical Biotechnology Unit, Department of Research and Development, Faculty of Medicine Siriraj Hospital, Mahidol University, Bangkok 10700 (Thailand); Yenchitsomanus, Pa-thai, E-mail: grpye@mahidol.ac.th [Division of Medical Molecular Biology and BIOTEC-Medical Biotechnology Unit, Department of Research and Development, Faculty of Medicine Siriraj Hospital, Mahidol University, Bangkok 10700 (Thailand)

    2010-10-08

    Research highlights: {yields} Trafficking defect of kAE1 is a cause of dRTA but trafficking pathway of kAE1 has not been clearly described. {yields} Adaptor-related protein complex 1 {mu}1A (AP-1 mu1A) was firstly reported to interact with kAE1. {yields} The interacting site for AP-1 mu1A on Ct-kAE1 was found to be Y904DEV907, a subset of YXXO motif. {yields} AP-1 mu1A knockdown showed a marked reduction of kAE1 on the cell membrane and its accumulation in endoplasmic reticulum. {yields} AP-1 mu1A has a critical role in kAE1 trafficking to the plasma membrane. -- Abstract: Kidney anion exchanger 1 (kAE1) mediates chloride (Cl{sup -}) and bicarbonate (HCO{sub 3}{sup -}) exchange at the basolateral membrane of kidney {alpha}-intercalated cells. Impaired trafficking of kAE1 leads to defect of the Cl{sup -}/HCO{sub 3}{sup -} exchange at the basolateral membrane and failure of proton (H{sup +}) secretion at the apical membrane, causing a kidney disease - distal renal tubular acidosis (dRTA). To gain a better insight into kAE1 trafficking, we searched for proteins physically interacting with the C-terminal region of kAE1 (Ct-kAE1), which contains motifs crucial for intracellular trafficking, by a yeast two-hybrid (Y2H) system. An adaptor-related protein complex 1 {mu}1A (AP-1 mu1A) subunit was found to interact with Ct-kAE1. The interaction between either Ct-kAE1 or full-length kAE1 and AP-1 mu1A were confirmed in human embryonic kidney (HEK) 293T by co-immunoprecipitation, affinity co-purification, co-localization, yellow fluorescent protein (YFP)-based protein fragment complementation assay (PCA) and GST pull-down assay. The interacting site for AP-1 mu1A on Ct-kAE1 was found to be Y904DEV907, a subset of YXXO motif. Interestingly, suppression of endogenous AP-1 mu1A in HEK 293T by small interfering RNA (siRNA) decreased membrane localization of kAE1 and increased its intracellular accumulation, suggesting for the first time that AP-1 mu1A is involved in the kAE1

  15. Human kidney anion exchanger 1 interacts with adaptor-related protein complex 1 μ1A (AP-1 mu1A)

    International Nuclear Information System (INIS)

    Research highlights: → Trafficking defect of kAE1 is a cause of dRTA but trafficking pathway of kAE1 has not been clearly described. → Adaptor-related protein complex 1 μ1A (AP-1 mu1A) was firstly reported to interact with kAE1. → The interacting site for AP-1 mu1A on Ct-kAE1 was found to be Y904DEV907, a subset of YXXO motif. → AP-1 mu1A knockdown showed a marked reduction of kAE1 on the cell membrane and its accumulation in endoplasmic reticulum. → AP-1 mu1A has a critical role in kAE1 trafficking to the plasma membrane. -- Abstract: Kidney anion exchanger 1 (kAE1) mediates chloride (Cl-) and bicarbonate (HCO3-) exchange at the basolateral membrane of kidney α-intercalated cells. Impaired trafficking of kAE1 leads to defect of the Cl-/HCO3- exchange at the basolateral membrane and failure of proton (H+) secretion at the apical membrane, causing a kidney disease - distal renal tubular acidosis (dRTA). To gain a better insight into kAE1 trafficking, we searched for proteins physically interacting with the C-terminal region of kAE1 (Ct-kAE1), which contains motifs crucial for intracellular trafficking, by a yeast two-hybrid (Y2H) system. An adaptor-related protein complex 1 μ1A (AP-1 mu1A) subunit was found to interact with Ct-kAE1. The interaction between either Ct-kAE1 or full-length kAE1 and AP-1 mu1A were confirmed in human embryonic kidney (HEK) 293T by co-immunoprecipitation, affinity co-purification, co-localization, yellow fluorescent protein (YFP)-based protein fragment complementation assay (PCA) and GST pull-down assay. The interacting site for AP-1 mu1A on Ct-kAE1 was found to be Y904DEV907, a subset of YXXO motif. Interestingly, suppression of endogenous AP-1 mu1A in HEK 293T by small interfering RNA (siRNA) decreased membrane localization of kAE1 and increased its intracellular accumulation, suggesting for the first time that AP-1 mu1A is involved in the kAE1 trafficking of kidney α-intercalated cells.

  16. Basic physical and chemical properties of ReillexTM-HPQ anion exchange resin and its sorption behavior of halides in aqueous nitric acid solution

    International Nuclear Information System (INIS)

    The ReillexTM-HPQ anion exchange resin has a good potential toward the pretreatment of liquid nuclear wastes. In this work, a short procedure was devised to convert 99.997% of the resin from its chloride form to the nitrate form as a foundation of all quantitative measurements. It is determined that the resin can be dried to a constant mass at 60 degree C in 28 hours and the electrostatic effect during weighings can hence be eliminated. The weight ratio between resins dried at 110 degree C and 60 degree C is 0.927±0.005 (one standard deviation). The resin has an apparent pKa of 3.36±0.05. The sorption capacity from primarily the weakly basic ionogenic sites (RNH+) is 1.08±0.04 meq/g for resins dried at 60 degree C. In highly basic solutions, the resin became unstable and started to release a substantial amount of methanol. In nitric acid solutions, the selectivity sequence of halide ions versus nitrate and pertechnetate ions is: TcO4- > I- > NO3- > Br- > Cl- > F-. The HPQ resin showed no sorption of fluoride ions. Although the sorption of chloride ions is also low the data can be modeled well by an equation similar to the Freundlich isotherm at a pH range between 2.0 and 3.0. Both bromide and iodide ions showed moderate sorptions when [HNO3] = 1.00 M and the sorption data can be fitted well to an equation closely related to the Temkin isotherm. 25 refs., 6 figs., 5 tabs

  17. A simple and rapid method for measuring α-D-phosphohexomutases activity by using anion-exchange chromatography coupled with an electrochemical detector.

    Science.gov (United States)

    Jia, Xiaochen; Kang, Jian; Yin, Heng

    2016-01-01

    The interconversion of hexose-6-phosphate and hexose-1-phosphate can be directly analyzed by high-performance anion-exchange chromatography coupled with an electrochemical detector (HPAEC-PAD). Thus, this method can be used to measure the activities of N-acetylglucosamine-phosphate mutase (AGM), glucosamine-phosphate mutase (GlmM) and phosphoglucomutase (PGM), which are the members of α-D-phosphohexomutases superfamily. The detection limits were extremely low as 2.747 pmol, 1.365 pmol, 0.512 pmol, 0.415 pmol, 1.486 pmol and 0.868 pmol for N-acetylglucosamine-1-phosphate (GlcNAc-1-P), N-acetylglucosamine-6-phosphate (GlcNAc-6-P), glucosamine-1-phosphate (GlcN-1-P), glucosamine-6-phosphate (GlcN-6-P), glucose-1-phosphate (Glc-1-P) and glucose-6-phosphate (Glc-6-P), respectively. By employing HPAEC-PAD, activities of AtAGM (AGM from Arabidopsis thaliana) on these six phosphohexoses can be detected. The Km of AtAGM on Glc-1-P determined by HPAEC-PAD was 679.18 ± 156.40 µM, which is comparable with the Km of 707.09 ± 170.36 µM detected by traditional coupled assay. Moreover, the activity of MtGlmM (GlmM from Mycobacterium tuberculosis) on GlcN-6-P tested by HPAEC-PAD was 7493.40 ± 309.12 nmol∕min ⋅ mg, which is much higher than 288.97 ± 35.28 nmol∕min ⋅ mg obtained by the traditional coupled assay. Accordingly, HPAEC-PAD is a more rapid and simple method than the traditional coupled assays given its high specificity and sensitivity, and will certainly bring convenience to further research of α-D-phosphohexomutases. PMID:26788420

  18. Simultaneous separation and quantitative determination of monosaccharides, uronic acids, and aldonic acids by high performance anion-exchange chromatography coupled with pulsed amperometric detection in corn stover prehydrolysates

    Directory of Open Access Journals (Sweden)

    Xing Wang

    2012-11-01

    Full Text Available A method for simultaneous separation and quantitative determination of arabinose, galactose, glucose, xylose, xylonic acid, gluconic acid, galacturonic acid, and glucuronic acid was developed by using high performance anion-exchange chromatography coupled with pulsed amperometric detection (HPAEC-PAD. The separation was performed on a CarboPacTM PA-10 column (250 mm × 2 mm with a various gradient elution of NaOH-NaOAc solution as the mobile phase. The calibration curves showed good linearity (R2 ≥ 0.9993 for the monosaccharides, uronic acids, and aldonic acids in the range of 0.1 to 12.5 mg/L. The detection limits (LODs and the quantification limits (LOQs were 4.91 to 18.75 μg/L and 16.36 to 62.50 μg/L, respectively. Relative standard deviations (RSDs of the retention times and peak areas for the seven consecutive determinations of an unknown amount of mixture were 0.15% to 0.44% and 0.22% to 2.31%, respectively. The established method was used to separate and determine four monosaccharides, two uronic acids, and two aldonic acids in the prehydrolysate from dilute acid steam-exploded corn stover within 21 min. The spiked recoveries of monosaccharides, uronic acids, and aldonic acids ranged from 91.25% to 108.81%, with RSDs (n=3 of 0.04% ~ 6.07%. This method was applied to evaluate the quantitative variation of sugar and sugar acid content in biomass prehydrolysates.

  19. Online determination of levoglucosan in ambient aerosols with Particle-into-Liquid Sampler – High-Performance Anion-Exchange Chromatography – Mass Spectrometry (PILS–HPAEC–MS

    Directory of Open Access Journals (Sweden)

    K. Saarnio

    2013-06-01

    Full Text Available Biomass burning, such as domestic heating, agricultural, and wild open-land fires, has a significant influence on the atmosphere at the global and, especially, at the local scale. Levoglucosan has been shown to be a good tracer for biomass burning emissions in atmospheric particulate matter and several analytical techniques have been presented for the determination of levoglucosan from filter samples. In this paper, a novel combination of a Particle-into-Liquid Sampler (PILS to a high-performance anion-exchange chromatograph (HPAEC with the detection by a mass spectrometer (MS is presented for the online analysis of levoglucosan in ambient particles. The PILS–HPAEC–MS technique enables a fast online analysis of levoglucosan from the particulate samples. The method was tested at an urban background station in Helsinki, Finland, in winter 2011. A comparison with simultaneous levoglucosan measurements from filter samples by the HPAEC–MS was performed and it showed a good agreement between the online and offline methods. Additionally, the online levoglucosan data were compared with the biomass burning tracer fragments measured by a High-Resolution Time-of-Flight Aerosol Mass Spectrometer (HR-ToF-AMS. As there were no local biomass burning sources close to the measurement station, online levoglucosan measurements revealed that most of the particles from biomass burning were either regionally distributed or long-range transported in the urban background of Helsinki. The average levoglucosan concentrations were relatively low (average 0.083 μg m−3 during the measurement campaign. The highest concentration peak measured for levoglucosan (1.4 μg m−3 seemed to originate from biomass burning in Eastern Europe, likely in Estonia, that was transported to Helsinki.

  20. Online determination of levoglucosan in ambient aerosols with particle-into-liquid sampler – high-performance anion-exchange chromatography – mass spectrometry (PILS–HPAEC–MS

    Directory of Open Access Journals (Sweden)

    K. Saarnio

    2013-10-01

    Full Text Available Biomass burning, such as domestic heating, agricultural, and wild open-land fires, has a significant influence on the atmosphere at the global and, especially, at the local scale. Levoglucosan has been shown to be a good tracer for biomass burning emissions in atmospheric particulate matter, and several analytical techniques have been presented for the determination of levoglucosan from filter samples. In this paper, a novel combination of a particle-into-liquid sampler (PILS to a high-performance anion-exchange chromatograph (HPAEC with the detection by a mass spectrometer (MS is presented for the online analysis of levoglucosan in ambient particles. The PILS–HPAEC–MS technique enables a fast online analysis of levoglucosan from the particulate samples. The method was tested at an urban background station in Helsinki, Finland, in winter 2011. A comparison with simultaneous levoglucosan measurements from filter samples by the HPAEC–MS was performed and it showed a good agreement between the online and offline methods. Additionally, the online levoglucosan data were compared with the biomass burning tracer fragments measured by a high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS. As there were no local biomass burning sources close to the measurement station, online levoglucosan measurements revealed that most of the particles from biomass burning were either regionally distributed or long-range transported in the urban background of Helsinki. The average levoglucosan concentrations were relatively low (average 0.083 μg m−3 during the measurement campaign. The highest concentration peak measured for levoglucosan (1.4 μg m−3 seemed to originate from biomass burning in the Baltic countries, likely in Estonia, that was transported to Helsinki.

  1. Online determination of levoglucosan in ambient aerosols with particle-into-liquid sampler - high-performance anion-exchange chromatography - mass spectrometry (PILS-HPAEC-MS)

    Science.gov (United States)

    Saarnio, K.; Teinilä, K.; Saarikoski, S.; Carbone, S.; Gilardoni, S.; Timonen, H.; Aurela, M.; Hillamo, R.

    2013-10-01

    Biomass burning, such as domestic heating, agricultural, and wild open-land fires, has a significant influence on the atmosphere at the global and, especially, at the local scale. Levoglucosan has been shown to be a good tracer for biomass burning emissions in atmospheric particulate matter, and several analytical techniques have been presented for the determination of levoglucosan from filter samples. In this paper, a novel combination of a particle-into-liquid sampler (PILS) to a high-performance anion-exchange chromatograph (HPAEC) with the detection by a mass spectrometer (MS) is presented for the online analysis of levoglucosan in ambient particles. The PILS-HPAEC-MS technique enables a fast online analysis of levoglucosan from the particulate samples. The method was tested at an urban background station in Helsinki, Finland, in winter 2011. A comparison with simultaneous levoglucosan measurements from filter samples by the HPAEC-MS was performed and it showed a good agreement between the online and offline methods. Additionally, the online levoglucosan data were compared with the biomass burning tracer fragments measured by a high-resolution time-of-flight aerosol mass spectrometer (HR-ToF-AMS). As there were no local biomass burning sources close to the measurement station, online levoglucosan measurements revealed that most of the particles from biomass burning were either regionally distributed or long-range transported in the urban background of Helsinki. The average levoglucosan concentrations were relatively low (average 0.083 μg m-3) during the measurement campaign. The highest concentration peak measured for levoglucosan (1.4 μg m-3) seemed to originate from biomass burning in the Baltic countries, likely in Estonia, that was transported to Helsinki.

  2. The many ways of making anionic clays

    Indian Academy of Sciences (India)

    Michael Rajamathi; Grace S Thomas; P Vishnu Kamath

    2001-10-01

    Together with hydrotalcite-like layered double hydroxides, bivalent and trivalent metal hydroxides and their hydroxy salts are actually anionic clays consisting of positively charged hydroxide layers with anions intercalated in the interlayer region. The anionic clays exhibit anion sorption, anion diffusion and exchange properties together with surface basicity making them materials of importance for many modern applications. In this article, we discuss many different ways of making anionic clays and compare and contrast the rich diversity of this class of materials with the better-known cationic clays.

  3. Distinct subcellular localization of alternative splicing variants of EFA6D, a guanine nucleotide exchange factor for Arf6, in the mouse brain.

    Science.gov (United States)

    Fukaya, Masahiro; Ohta, Shingo; Hara, Yoshinobu; Tamaki, Hideaki; Sakagami, Hiroyuki

    2016-09-01

    EFA6D (guanine nucleotide exchange factor for ADP-ribosylation factor 6 [Arf6]D) is also known as EFA6R, Psd3, and HCA67. It is the fourth member of the EFA6 family with guanine nucleotide exchange activity for Arf6, a small guanosine triphosphatase (GTPase) that regulates endosomal trafficking and actin cytoskeleton remodeling. We propose a classification and nomenclature of 10 EFA6D variants deposited in the GenBank database as EFA6D1a, 1b, 1c, 1d, 1s, 2a, 2b, 2c, 2d, and 2s based on the combination of N-terminal and C-terminal insertions. Polymerase chain reaction analysis showed the expression of all EFA6D variants except for variants a and d in the adult mouse brain. Immunoblotting analysis with novel variant-specific antibodies showed the endogenous expression of EFA6D1b, EFA6D1c, and EFA6D1s at the protein level, with the highest expression being EFA6D1s, in the brain. Immunoblotting analysis of forebrain subcellular fractions showed the distinct subcellular distribution of EFA6D1b/c and EFA6D1s. The immunohistochemical analysis revealed distinct but overlapping immunoreactive patterns between EFA6D1b/c and EFA6D1s in the mouse brain. In immunoelectron microscopic analyses of the hippocampal CA3 region, EFA6D1b/c was present predominantly in the mossy fiber axons of dentate granule cells, whereas EFA6D1s was present abundantly in the cell bodies, dendritic shafts, and spines of hippocampal pyramidal cells. These results provide the first anatomical evidence suggesting the functional diversity of EFA6D variants, particularly EFA6D1b/c and EFA6D1s, in neurons. J. Comp. Neurol. 524:2531-2552, 2016. © 2016 Wiley Periodicals, Inc. PMID:27241101

  4. Novel anion exchange polymer membranes

    Czech Academy of Sciences Publication Activity Database

    Žitka, Jan; Schauer, Jan; Bleha, M.; Hnát, J.; Bouzek, K.

    Praha : Orgit, 2012. s. 50. ISBN 978-80-905035-2-6. [Electromembrane Processes and Materials - ELMEMPRO 2012, Satellite Meeting of The International Society of Electrochemistry Annual Meeting /63./. 26.08.2012-29.08.2012, Český Krumlov] Institutional research plan: CEZ:AV0Z40500505 Keywords : AEM * alkaline electrolysis Subject RIV: CD - Macromolecular Chemistry

  5. IMPROVING OF ANION EXCHANGERES REGENERATION

    Directory of Open Access Journals (Sweden)

    Muzher M. Ibrahim

    2013-05-01

    Full Text Available Inthis study, Different basis [NaOH and KOH] of variable concentration are usedto reactivate Anion exchangers employing different schemes .The Laboratoryresults showed large improvement in efficiency of these exchangers ( i.eoperating time was increased from 12 to 42 hours .The results of this work showed that the environmentalload (waste water can be reduced greatly when using the proposed regenerationscheme .

  6. Tens of micron-sized unilamellar nanosheets of Y/Eu layered rare-earth hydroxide: efficient exfoliation via fast anion exchange and their self-assembly into oriented oxide film with enhanced photoluminescence

    Directory of Open Access Journals (Sweden)

    Qi Zhu

    2014-01-01

    Full Text Available Layered rare-earth hydroxide (LRH crystals of (Y0.95Eu0.052(OH5NO3centerdotnH2O with a lateral size of ~ 300 μm and a thickness of ~ 9 μm have been synthesized via a hydrothermal reaction of mixed nitrate solutions in the presence of mineralizer NH4NO3 at 200 °C for 24 h. LRH exhibits the ability to undergo intercalation and anion exchange with DS− (C12H25OSO3− via hydrothermal treatment. Compared with traditional anion exchange at room temperature, hydrothermal processing not only shortens the anion exchange time from 720 to 24 h but also increases the basal spacing. The arrangements of DS− in the interlayer of LRH are significantly affected by the DS− concentration and reaction temperature, and the basal spacing of the LRH-DS sample in the crystal edge is assumed to be larger than that in the crystal center. A higher DS− concentration and reaction temperature both induce more intercalation of DS− anions into the interlayer gallery, thus yielding a larger basal spacing. Unilamellar nanosheets with a lateral size of ≥60 μm and a thickness of ~ 1.6 nm can be obtained by delaminating LRH-DS in formamide. The resultant unilamellar nanosheets are single crystalline. Transparent (Y0.95Eu0.052O3 phosphor films with a uniform [111] orientation and a layer thickness of ~ 90 nm were constructed with the nanosheets as building blocks via spin-coating, followed by proper annealing. The oriented oxide film exhibits a strong red emission at 614 nm (the 5D0–7F2 transition of Eu3+, whose intensity is ~ 2 times that of the powder form owing to the significant exposure of the (222 facets.

  7. Determination of nitric oxide metabolites, nitrate and nitrite, in Anopheles culicifacies mosquito midgut and haemolymph by anion exchange high-performance liquid chromatography: plausible mechanism of refractoriness

    Directory of Open Access Journals (Sweden)

    Adak Tridibesh

    2008-04-01

    Full Text Available Abstract Background The diverse physiological and pathological role of nitric oxide in innate immune defenses against many intra and extracellular pathogens, have led to the development of various methods for determining nitric oxide (NO synthesis. NO metabolites, nitrite (NO2- and nitrate (NO3- are produced by the action of an inducible Anopheles culicifacies NO synthase (AcNOS in mosquito mid-guts and may be central to anti-parasitic arsenal of these mosquitoes. Method While exploring a plausible mechanism of refractoriness based on nitric oxide synthase physiology among the sibling species of An. culicifacies, a sensitive, specific and cost effective high performance liquid chromatography (HPLC method was developed, which is not influenced by the presence of biogenic amines, for the determination of NO2- and NO3- from mosquito mid-guts and haemolymph. Results This method is based on extraction, efficiency, assay reproducibility and contaminant minimization. It entails de-proteinization by centrifugal ultra filtration through ultracel 3 K filter and analysis by high performance anion exchange liquid chromatography (Sphereclone, 5 μ SAX column with UV detection at 214 nm. The lower detection limit of the assay procedure is 50 pmoles in all midgut and haemolymph samples. Retention times for NO2- and NO3- in standards and in mid-gut samples were 3.42 and 4.53 min. respectively. Assay linearity for standards ranged between 50 nM and 1 mM. Recoveries of NO2- and NO3- from spiked samples (1–100 μM and from the extracted standards (1–100 μM were calculated to be 100%. Intra-assay and inter assay variations and relative standard deviations (RSDs for NO2- and NO3- in spiked and un-spiked midgut samples were 5.7% or less. Increased levels NO2- and NO3- in midguts and haemolymph of An. culicifacies sibling species B in comparison to species A reflect towards a mechanism of refractoriness based on AcNOS physiology. Conclusion HPLC is a sensitive

  8. Speciation of chromium in wastewater and sludge by extraction with liquid anion exchanger Amberlite LA-2 and electrothermal atomic absorption spectrometry

    International Nuclear Information System (INIS)

    A simple, integrated method for the speciation of chromium in wastewater and sewage sludge was developed, utilising liquid anion exchange by Amberlite LA-2 (LAES) and final determination by electrothermal atomic absorption spectrometry (ETAAS). Samples were filtered through a 0.45 μm membrane filter and chromium species were determined in filtered water samples and in sludge on the filters. In the former case (filtrate), total Cr was determined directly by ETAAS, while for the determination of Cr(VI) the filtrate was buffered to pH 6.4, extracted with LAES and Cr(VI) was determined in the organic extract. Cr(III) was determined by the difference. In the latter case (filter), the filters were leached with an alkaline buffer solution (pH 12.7) and the supernatant was subjected to the same extraction procedure. For the determination of total leachable Cr, the filters were subjected to acid leaching with dilute HNO3 (pH 1) and the supernatant was subjected to ETAAS, after appropriate dilution with water. Then, Cr(III) was determined by the difference. The limits of detection (LOD) were 0.39 and 0.45 μg l-1 for total Cr and Cr(VI), respectively, in the dissolved phase and 2.10 and 0.87 ng g-1 for total Cr and Cr(VI) in the suspended solids. The recoveries of total Cr and Cr(VI) in filtrated wastewater samples and filters were quantitative, ranged from 93 to 106%. The effect of time and temperature of sonication and suspended solids concentration on total Cr and Cr(VI) recovery was studied. No significant difference in recoveries was obtained for sonication temperatures between 30 and 70 deg. C. However, sonication time equal to or higher than 30 min and concentration of suspended solids equal to or less than 30 mg significantly improved Cr recovery. The ETAAS program for the determination of Cr(VI) in Amberlite/MIBK extract was carefully optimised in the absence of a chemical modifier to avoid memory effects. The developed analytical method was applied for the

  9. Tandem anion and cation exchange solid phase extraction for the enrichment of micropollutants and their transformation products from ozonation in a wastewater treatment plant.

    Science.gov (United States)

    Deeb, Ahmad A; Schmidt, Torsten C

    2016-06-01

    The presence of organic micropollutants and their transformation products (TPs) from biotic and abiotic processes in aquatic environments is receiving intense public and scientific attention. Yet a suitable sample preparation method that would enable extraction and enrichment of a wide range of such compounds from water is missing. The focus of this paper was to develop an enhanced solid phase extraction (SPE) protocol which enabled isolation of parent compounds and low molecular weight transformation products (that are produced after treatment of water with ozone) from different water matrices. Ten SPE sorbents were evaluated with regard to their ability to extract acidic, neutral, and basic compounds from water at several pH values. Highest recoveries (91-99 %) for all analytes in pure water were obtained by combining strong anion and cation exchangers of two manufacturers in a tandem mode without pH adjustment. Tandem Oasis (MAX+MCX) was finally applied to extract the spiked analytes from tap water, surface water, and several wastewater samples. The efficiency of the used SPE procedure was examined using an optimized liquid chromatography-electrospray ionization-tandem mass spectrometry (LC-ESI-MS/MS) method using multiple reaction monitoring (MRM) mode. The occurrence of some of the investigated TPs in environmental water matrices was proven for the first time in this study. Method quantification limits (MQLs) for all compounds ranged from 3.7 to 15.3 ng/L in all matrices. Recoveries (%RE) were between 90 and 110 %. Intraday and interday precision, expressed as relative standard deviation, varied from 0.7 to 5.9 % and 1.8 to 10.3 %, respectively. Matrix effect (%ME) evaluation demonstrated that even complex sample matrices did not show significant ion suppression or enhancement. The applicability of the method was shown during two sampling campaigns at Ruhr river and a wastewater treatment plant (WWTP) equipped with an ozonation step after regular

  10. Ion exchange equilibrium constants

    CERN Document Server

    Marcus, Y

    2013-01-01

    Ion Exchange Equilibrium Constants focuses on the test-compilation of equilibrium constants for ion exchange reactions. The book first underscores the scope of the compilation, equilibrium constants, symbols used, and arrangement of the table. The manuscript then presents the table of equilibrium constants, including polystyrene sulfonate cation exchanger, polyacrylate cation exchanger, polymethacrylate cation exchanger, polysterene phosphate cation exchanger, and zirconium phosphate cation exchanger. The text highlights zirconium oxide anion exchanger, zeolite type 13Y cation exchanger, and

  11. Investigating the Interaction between the Neonatal Fc Receptor and Monoclonal Antibody Variants by Hydrogen/Deuterium Exchange Mass Spectrometry

    DEFF Research Database (Denmark)

    Jensen, Pernille Foged; Larraillet, Vincent; Schlothauer, Tilman; Kettenberger, Hubert; Hilger, Maximiliane; Rand, Kasper D

    2015-01-01

    The recycling of immunoglobulins by the neonatal Fc receptor (FcRn) is of crucial importance in the maintenance of antibody levels in plasma and is responsible for the long half-lives of endogenous and recombinant monoclonal antibodies. From a therapeutic point of view there is great interest in...... understanding and modulating the IgG-FcRn interaction to optimize antibody pharmacokinetics and ultimately improve efficacy and safety. Here we studied the interaction between a full-length human IgG1 and human FcRn via hydrogen/deuterium exchange mass spectrometry and targeted electron transfer dissociation to...... wild-type glycosylated IgG. Our results provide new molecular insight into the IgG-FcRn interaction and illustrate the capability of hydrogen/deuterium exchange mass spectrometry to advance structural proteomics by providing detailed information on the conformation and dynamics of large protein...

  12. The poisoning effect of mercury complexes with an anionic exchange membrane used in an electrodialysis process: a Raman study; Etude par spectrometrie Raman de l`empoisonnement d`une membrane echangeuse d`anions, par des complexes mercuriques, au cours d`un procede d`electrodialyse

    Energy Technology Data Exchange (ETDEWEB)

    Chaouki, M.; Huguet, P.; Persin, F.; Bribes, J.L. [Montpellier-2 Univ., 34 (France). Laboratoire des Materiaux et des Pocedes Membrnaires, CNRS UMR 5635

    1998-03-01

    Electrodialysis is a powerful technique for the treatment of many waste acids. However, some important problems can be encountered if poisoning of the ionic exchange membrane occurs. This is the case in the purification and concentration process of hydrochloric acid solutions containing zinc, cadmium or mercury chlorides, because metallic complexes formation gives rise to an important poisoning effect of the membranes used. In this work, the poisoning of an anion exchange membrane, used in an electrodialysis process to purify and reconcentrate an hydrochloric acid solution containing mercury chloride, has been investigated. Raman spectroscopic analysis of the contaminated material, combined with electrodialysis results, are presented and discussed. The stoichiometry of the poisoning mercury complex and its action as a counter ion inside the membrane are determined. Moreover, a strong interaction between the membrane fixed sites and the mercury complex is pointed out. (authors) 11 refs.

  13. Evaluation of glycidyl methacrylate-based monolith functionalized with weak anion exchange moiety inside 0.5 mm i.d. column for liquid chromatographic separation of DNA

    Directory of Open Access Journals (Sweden)

    Aprilia Nur Tasfiyati

    2016-03-01

    Full Text Available In this study, the organic polymer monolith was developed as a weak anion exchanger column in high performance liquid chromatography for DNA separation. Methacrylate-based monolithic column was prepared in microbore silicosteel column (100 × 0.5 mm i.d. by in-situ polymerization reaction using glycidyl methacrylate as monomer; ethylene dimethacrylate as crosslinker; 1-propanol, 1,4-butanediol, and water as porogenic solvents, with the presence of initiator α,α′-azobisisobutyronitrile (AIBN. The monolith matrix was modified with diethylamine to create weak anion exchanger via ring opening reaction of epoxy groups. The morphology of the monolithic column was studied by SEM. The properties of the monolithic column, such as permeability, mechanical stability, binding capacity and pore size distribution, were characterized in detail. From the results of the characterization, monoliths poly-(GMA-co-EDMA with total monomer percentage (%T 40 and crosslinker percentage (%C 25 was found to be the ideal composition of monomer and crosslinker. It has good mechanical stability and high permeability, adequate molecular recognition sites (represented with binding capacity value of 36 mg ml−1, and has relatively equal proportion of flow-through pore and mesopores (37.2% and 41.1% respectively. Poly-(GMA-co-EDMA with %T 40 and %C 25 can successfully separate oligo(dT12–18 and 50 bp DNA ladder with good resolution.

  14. Oxidative degradation of anion exchange resin in chloride form during purification of reactor coolant after alkaline permanganate treatment in dilute chemical decontamination

    International Nuclear Information System (INIS)

    In boiling water reactors, primary system piping is contaminated by radioactive species like 51Cr and 60Co, resulting in high radiation fields. Dilute Chemical Decontamination (DCD) is a preferred choice to reduce the radiation field. In DCD process, oxidation step involving alkaline permanganate or acid permanganate is employed for effective dissolution of oxides (rich in chromium), from the metal surfaces of reactor components. After completion of the oxidation step, removal of the unused chemicals is carried out by the use of ion exchange process. This poses a problem of possible degradation of ion exchange resin by the oxidative chemicals during the removal. In this paper, this aspect has been investigated and the results obtained are discussed. (author)

  15. High Performance of Alkaline Anion-Exchange Membranes Based on Chitosan/Poly (vinyl) Alcohol Doped with Graphene Oxide for the Electrooxidation of Primary Alcohols

    OpenAIRE

    García Cruz, Leticia; Casado-Coterillo, Clara; Irabien, Ángel; Montiel Leguey, Vicente; Iniesta Valcárcel, Jesús

    2016-01-01

    Mixed matrix membranes (MMM) based on chitosan (CS) and poly (vinyl) alcohol (PVA) with a 50:50 w/w ratio doped with graphene oxide (GO) are prepared by solution casting and characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), thermogravimetric analysis (TGA), water uptake, alcohol permeability, ion exchange capacity (IEC) and OH− conductivity measurements. The SEM analysis revealed a dense MMM where the GO nanosheets were well dispersed over the entire polymer matrix...

  16. Removal of Evans Blue and Yellow thiazole dyes from aqueous solution by Mg-Al-CO3 Layered Double Hydroxides as anion-exchanger

    Directory of Open Access Journals (Sweden)

    Mohamed Bouraada

    2014-06-01

    Full Text Available Mg-Al-CO3 Layered double hydroxide (LDH was prepared by co-precipitation method at constant pH, and subsequently used to remove Evans Blue (EB and Yellow thiazole (YT dyes from aqueous solutions. The obtained material was characterized by powder X-ray diffraction (PXRD, Fourier transform infrared spectroscopy (FTIR, thermal analysis and BET. The kinetic and equilibrium aspects of sorption of the anionic dyes from aqueous solution by Mg-Al-CO3 were investigated in batch mode. The sorption kinetic data were found to be consistent with the pseudo-second-order model. Data for YT and EB sorption by Mg-Al-CO3 were fitted better by the Langmuir equation than by the Freundlich equation based on the determination coefficient values R2 . The maximum adsorption capacities of 222.2 mgg-1 for Yellow thiazole and 107.5 mgg-1 for Evans blue. The thermodynamic parameters including Gibbs free energy (G°, standard enthalpy change (H°, and standard entropy change (S° for the process were calculated. The negative G° value indicates the spontaneity of the removal process.

  17. Thermodynamic modeling of Cl(-), NO3(-) and SO4(2-) removal by an anion exchange resin and comparison with Dubinin-Astakhov isotherms.

    Science.gov (United States)

    Dron, Julien; Dodi, Alain

    2011-03-15

    The removal of chloride, nitrate, and sulfate ions from wastewaters by a macroporous ion-exchange resin is studied through the experimental results obtained for six ion exchange systems, OH(-)/Cl(-), OH(-)/NO3(-), OH(-)/SO4(2-), and HCO3(-)/Cl(-), Cl(-)/NO3(-), Cl(-)/SO4(2-). The results are described through thermodynamic modeling, considering either an ideal or a nonideal behavior of the ionic species in the liquid and solid phases. The nonidealities are determined by the Davies equation and Wilson equations in the liquid and solid phases, respectively. The results show that the resin has a strong affinity for all the target ions, and the order of affinity obtained is OH(-) < HCO3(-) < Cl(-) < NO3(-) < SO4(2-). The calculation of the changes in standard Gibbs free energies (ΔG(0)) shows that even though HCO3(-) has a lower affinity to the resin, it may affect the removal of Cl(-), and in the same way that Cl(-) may affect the removal of NO3(-) and SO4(2-). The application of nonidealities in the thermodynamic model leads to an improved fit of the model to the experimental data with average relative deviations below 1.5% except for the OH(-)/SO4(2-) system. On the other hand, considering ideal or nonideal behaviors has no significant impact on the determination of the selectivity coefficients. The thermodynamic modeling is also compared with the Dubinin-Astakhov adsorption isotherms obtained for the same ion exchange systems. Surprisingly, the latter performs significantly better than the ideal thermodynamic model and nearly as well as the nonideal thermodynamic model. PMID:21332215

  18. A new method for separation and determination of Cr(III) and Cr(VI) in water samples by high-performance liquid chromatography based on anion exchange stationary phase of ionic liquid modified silica.

    Science.gov (United States)

    Sadeghi, Susan; Moghaddam, Ali Zeraatkar

    2015-12-01

    In this work, N-methylimidazolium-chloride ionic liquid functionalized silica was prepared and used as an anion-exchange stationary phase for separation of chromium species by high-performance liquid chromatography (HPLC) with UV detection at 200 nm. The Cr(VI) as HCr2O7(-) and chelated Cr(III) with potassium hydrogen phthalate (PHP) as Cr(PHP)2 (-) was retained on the prepared column and separated using a mobile phase composed of 5% methanol in 25 mM phosphate buffer at pH 6.5. Several variables affecting the chelation/separation steps were modeled by response surface methodology (RSM) using Box-Behnken (BBD) design. The significance of the independent variables and their interactions were tested by the analysis of variances (ANOVA) with 95% confidence limit. Under the optimized conditions, the Cr(III) and Cr(VI) anionic species were well separated with a single peak for each Cr species at retention times of 2.3 and 4.3 min, respectively. The relationship between the peak area and concentration was linear in the range of 0.025-30 for Cr(III) and 0.5-20 mg L(-1) for Cr(VI) with detection limits of 0.010 and 0.210 mg L(-1) for Cr(III) and Cr(VI), respectively. The proposed method was validated by simultaneous separation and determination of the Cr species in tap and underground water samples without impose to any pretreatment. PMID:26526699

  19. 布洛芬在阴离子交换树脂上的负载及其缓释%LOADING AND SUSTAINED RELEASE OF IBUPROFEN IN ANION EXCHANGE RESINS

    Institute of Scientific and Technical Information of China (English)

    张月恒; 阙茝璐; 张更辉; 阎虎生

    2012-01-01

    将布洛芬通过静电和疏水作用的共同作用负载于聚苯乙烯型大孔弱碱性阴离子交换树脂D301R和D301T上,最佳负载条件为:布洛芬悬浮于5~10%的乙醇水溶液中,加入树脂后在60℃下搅拌12h,负载量可达到0.49g/g树脂.研究了负载的布洛芬在模拟胃肠道的条件下(pH2下2h、pH 7.4下4h和pH 6.7下18h)的释放动力学,在前12h的释放接近于线性释放,释放率为58~60%.后12h的释放量较小,释放率为13~17%.如果每12h服药1次,第2次服药后的24h的累加释放率接近于线性释放.与聚苯乙烯骨架的大孔弱碱性阴离子交换树脂相比,聚甲基丙烯酸酯骨架的弱碱性阴离子交换树脂(甲基丙烯酸正丁酯/甲基丙烯酸N,N-二甲胺基乙酯/双甲基丙烯酸乙二醇酯共聚物)负载的布洛芬在相同释放条件下突释明显,表明布洛芬与苯乙烯型弱碱性阴离子交换树脂之间的π-π作用在布洛芬的缓释中起关键的作用.%Ibuprofen was loaded into polystyrene-based macroporous weakly basic anion exchange resins, D301R and D301T. The loading was driven by electrostatic and hydrophobic interactions. The optimized loading condition was: a suspension of the resin in 5~10% ethanol aqueous solution with dispersed ibuprofen was stirred for 12h at 60℃. The loading capacity could be up to 0.49g/g resin. The release of the loaded ibuprofen in buffer mimicking gastrointestinal Ph environments (2h, 4h and 18h at Ph 2, 7.4 and 6.7, respectively) was studied. The loaded ibuprofen was released almost linearly against time in the first 12h with release percentage of 58~60%. The release percentage in the followed 12h was quite low, being 13-17%. In simulated administrations taken at 12h interval, the loaded ibuprofen in D301R was released almost linearly against time during a 24h period after the second administration. In contrast, an initial burst release of the loaded ibuprofen in a polymethacrylate-based weakly basic anion

  20. Comparison of adsorption equilibrium models for the study of CL-, NO3- and SO4(2-) removal from aqueous solutions by an anion exchange resin.

    Science.gov (United States)

    Dron, Julien; Dodi, Alain

    2011-06-15

    The removal of chloride, nitrate and sulfate ions from aqueous solutions by a macroporous resin is studied through the ion exchange systems OH(-)/Cl(-), OH(-)/NO(3)(-), OH(-)/SO(4)(2-), and HCO(3)(-)/Cl(-), Cl(-)/NO(3)(-), Cl(-)/SO(4)(2-). They are investigated by means of Langmuir, Freundlich, Dubinin-Radushkevitch (D-R) and Dubinin-Astakhov (D-A) single-component adsorption isotherms. The sorption parameters and the fitting of the models are determined by nonlinear regression and discussed. The Langmuir model provides a fair estimation of the sorption capacity whatever the system under study, on the contrary to Freundlich and D-R models. The adsorption energies deduced from Dubinin and Langmuir isotherms are in good agreement, and the surface parameter of the D-A isotherm appears consistent. All models agree on the order of affinity OH(-)exchange processes under study among other adsorption isotherms. The nonlinear regression results are also compared with linear regressions. While the parameter values are not affected, the evaluation of the best fitting model is biased by linearization. PMID:21497015

  1. An investigation of the applicability of the new Reillex(tm)-HPQ anion exchange resin system for technetium/rhenium and uranium in the Hanford waste tanks

    Science.gov (United States)

    Ashley, K. R.; Ball, J. R.; Cobb, S. L.; Adams, J. M.; Young, D. A.

    1994-09-01

    Results of the measurements of the exchange capacity and K(sub d) values for ReO4(-) on Reillex(tm)-HPQ as a function of nitric acid and hydroxide concentration, temperature, and ten months time will be reported. Results of the breakthrough volumes for UO2(2+) on Reillex-HPQ chromatography columns as a function of carbonate ion concentration in high nitrate ion concentrations and various column sizes will be reported. Individual sections of this report describe the following: the sorption behavior of ReO4(-) on the Reillex-HPQ between pH 2 and 12 in 1.00 M NaNO3; results of the measurements of the K(sub d) values for ReO4(-) on Reillex-HPQ and on Reillex-HP as a function of nitrate and hydroxide ion concentrations; the sorption behavior of ReO4(-) on Reillex-HPQ resin in base with time as a variable; the results of the early attempts at determining the K(sub d) values for Na4UO2(CO3)3 on Reillex-HPQ resin; and the breakthrough of UO2(NO3)2 in varying nitric acid solutions on Reillex-HPQ columns.

  2. High-performance liquid chromatography - Ultraviolet method for the determination of total specific migration of nine ultraviolet absorbers in food simulants based on 1,1,3,3-Tetramethylguanidine and organic phase anion exchange solid phase extraction to remove glyceride.

    Science.gov (United States)

    Wang, Jianling; Xiao, Xiaofeng; Chen, Tong; Liu, Tingfei; Tao, Huaming; He, Jun

    2016-06-17

    The glyceride in oil food simulant usually causes serious interferences to target analytes and leads to failure of the normal function of the RP-HPLC column. In this work, a convenient HPLC-UV method for the determination of the total specific migration of nine ultraviolet (UV) absorbers in food simulants was developed based on 1,1,3,3-tetramethylguanidine (TMG) and organic phase anion exchange (OPAE) SPE to efficiently remove glyceride in olive oil simulant. In contrast to the normal ion exchange carried out in an aqueous solution or aqueous phase environment, the OPAE SPE was performed in the organic phase environments, and the time-consuming and challenging extraction of the nine UV absorbers from vegetable oil with aqueous solution could be readily omitted. The method was proved to have good linearity (r≥0.99992), precision (intra-day RSD≤3.3%), and accuracy(91.0%≤recoveries≤107%); furthermore, the lower limit of quantifications (0.05-0.2mg/kg) in five types of food simulants(10% ethanol, 3% acetic acid, 20% ethanol, 50% ethanol and olive oil) was observed. The method was found to be well suited for quantitative determination of the total specific migration of the nine UV absorbers both in aqueous and vegetable oil simulant according to Commission Regulation (EU) No. 10/2011. Migration levels of the nine UV absorbers were determined in 31 plastic samples, and UV-24, UV-531, HHBP and UV-326 were frequently detected, especially in olive oil simulant for UV-326 in PE samples. In addition, the OPAE SPE procedure was also been applied to efficiently enrich or purify seven antioxidants in olive oil simulant. Results indicate that this procedure will have more extensive applications in the enriching or purification of the extremely weak acidic compounds with phenol hydroxyl group that are relatively stable in TMG n-hexane solution and that can be barely extracted from vegetable oil. PMID:27189432

  3. Efficiency of pretreatment of aqueous samples using a macroporous strong anion-exchange resin on the determination of nerve gas hydrolysis products by gas chromatography-mass spectrometry after tert.-butyldimethylsilylation.

    Science.gov (United States)

    Kataoka, M; Tsuge, K; Seto, Y

    2000-09-01

    A pretreatment procedure, using a macroporous strong anion-exchange resin (MSA) has been established for the determination of nerve gas hydrolysis products by gas chromatography-mass spectrometry (GC-MS) after tert.-butyldimethylsilyl (TBDMS) derivatization. Aqueous solutions of methylphosphonic acid (MPA) and three alkyl methylphosphonic acids (AMPAs) (ethyl, isopropyl and pinacolyl methylphosphonic acid), were retained on the MSA column, and then quantitatively eluted with 0.1 M hydrochloric acid. The neutralized column eluate was dried, and MPA and AMPAs were derivatized with N-methyl-N-(tert.-butyldimethylsilyl)-trifluoroacetamide and analyzed by GC-MS. The column eluate was also analyzed in order to determine the exact hydrolysis product levels by capillary electrophoresis using borate and benzoate buffer (pH 6). The MSA pretreatment was examined for the clean-up of aqueous extracts of three types of soils and an aqueous solution containing 10% sucrose, which is regarded as model for a typical soft drink, after spiking with MPA and AMPAs. MPA and AMPAs were quantitatively recovered in the MSA eluate fraction from those samples, except for MPA from volcanic acid and alluvial soils. The yields of TBDMS derivatives were remarkably improved, compared with for which no pretreatment was used and also for those in which a strong cation-exchange resin was used. The achieved detection limits of MPA and AMPAs ranged from 0.12 to 0.18 microg/g of soil (S/N=3). The established MSA method was applied to the pretreatment of spiked sea water, two types of beverages, Pepsi Cola and canned coffee. Although the yields of TBDMS derivatives of MPA and AMPAs in sea water (in a range between 44 and 96%) and AMPAs in Pepsi Cola (in a range between 58 and 92%) were rather high, those for MPA in the Pepsi Cola (27%) and those for MPA and AMPAs in the canned coffee (in a range between 5 and 17%) were low. PMID:11043790

  4. Method for immobilizing invertase by adsorption on Dowex® anionic exchange resin Método para a imobilização da invertase por adsorção em resinas trocadoras de ânions (DOWEX

    Directory of Open Access Journals (Sweden)

    Ester Junko Tomotani

    2006-06-01

    Full Text Available This communication describes a method for adsorbing the invertase (EC.3.2.1.26 on DOWEX® anion exchange resin. Among the types of DOWEX® resins studied (1x8:50-400; 1x4:50-400 and 1x2:100-400, 1X4-200 was the most suitable, because it adsorbed the invertase molecules completely and the complex 1X4-200/invertase retained 100% of the catalytic activity. Moreover, no leakage of enzyme from the support was noted at the end of the sucrose hydrolysis.O presente trabalho descreve um método de adsorção da invertase (EC. 3.2.1.26 na resina de troca aniônica do tipo Dowex®. Entre os tipos de resinas Dowex® estudados (1x8:50-400; 1x4:50-400 e 1x2:100-400, 1x4-200 foi a mais apropriada devido à completa adsorção das moléculas de invertase e a sua retenção de atividade catalítica de 100% do complexo 1x4-200/invertase. Salienta-se ainda a ausência do desprendimento da enzima do suporte após o término da hidrólise da sacarose.

  5. Speciation analysis of calcium, iron, and zinc in casein phosphopeptide fractions from toddler milk-based formula by anion exchange and reversed-phase high-performance liquid chromatography-mass spectrometry/flame atomic-absorption spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Miquel, Esther; Alegria, Amparo; Barbera, Reyes; Farre, Rosaura [University of Valencia, Nutrition and Food Chemistry, Faculty of Pharmacy, Burjassot, Valencia (Spain)

    2005-03-01

    Casein phosphopeptides (CPP) are phosphorylated casein-derived peptides that can be released by in-vitro or in-vivo enzymatic hydrolysis of {alpha}{sub s1}-casein, {alpha}{sub s2}-casein, and {beta}-casein (CN). Many of these peptides contain a highly polar acidic sequence of three phosphoseryl groups followed by two glutamic acid residues. These domains are binding sites for minerals such as calcium, iron, and zinc and play an important role in mineral bioavailability. The aim of this study was speciation analysis of calcium, iron, and zinc in CPP fractions from the soluble fraction of a toddler milk-based formula. Methods for CPP separation by anion-exchange high-performance liquid chromatography (AE-HPLC) were combined with CPP identification by reversed-phase high performance liquid chromatography-electrospray ionization mass spectrometry and determination of the calcium, iron, zinc, and phosphorus content of the fractions obtained by AE-HPLC. Calcium and phosphorus were detected in all the analyzed AE-HPLC fractions. Calcium and zinc could be bound to CPP derived from {alpha}{sub s1}-CN and {alpha}{sub s2}-CN in fraction 3. Iron could be bound to CPP in fraction 4 in which {beta}-CN(15-34)4P was present with the cluster sequence S(P)S(P)S(P)EE. The results obtained prove the different distribution of calcium, iron, and zinc in heterogeneous CPP fractions. (orig.)

  6. Cellulase variants

    Energy Technology Data Exchange (ETDEWEB)

    Blazej, Robert; Toriello, Nicholas; Emrich, Charles; Cohen, Richard N.; Koppel, Nitzan

    2015-07-14

    This invention provides novel variant cellulolytic enzymes having improved activity and/or stability. In certain embodiments the variant cellulotyic enzymes comprise a glycoside hydrolase with or comprising a substitution at one or more positions corresponding to one or more of residues F64, A226, and/or E246 in Thermobifida fusca Cel9A enzyme. In certain embodiments the glycoside hydrolase is a variant of a family 9 glycoside hydrolase. In certain embodiments the glycoside hydrolase is a variant of a theme B family 9 glycoside hydrolase.

  7. Anions in Cometary Comae

    Science.gov (United States)

    Charnley, Steven B.

    2011-01-01

    The presence of negative ions (anions) in cometary comae is known from Giotto mass spectrometry of IP/Halley. The anions 0-, OH-, C-, CH- and CN- have been detected, as well as unidentified anions with masses 22-65 and 85-110 amu (Chaizy et al. 1991). Organic molecular anions are known to have a significant impact on the charge balance of interstellar clouds and circumstellar envelopes and have been shown to act as catalysts for the gas-phase synthesis of larger hydrocarbon molecules in the ISM, but their importance in cometary comae has not yet been explored. We present details of the first attempt to model the chemistry of anions in cometary comae. Based on the combined chemical and hydro dynamical model of Rodgers & Charnley (2002), we investigate the role of large carbon-chain anions in cometary coma chemistry. We calculate the effects of these anions on coma thermodynamics, charge balance and examine their impact on molecule formation.

  8. Adsorption and Desorption Properties of Phytic Acid from Rice Bran on Anion Exchange Resin%阴离子交换树脂对米糠植酸的吸附解吸性能

    Institute of Scientific and Technical Information of China (English)

    王琳; 罗建平; 查学强; 张海林; 潘利华

    2011-01-01

    通过静态和动态试验研究了6种阴离子交换树脂对植酸的吸附与解吸性能.结果表明,D201树脂对植酸的吸附交换作用较好,且在pH值为2.2时吸附能力最强,静态吸附量达到94.54 mg/g,1.5 mol/L的NaOH溶液利于植酸解吸;Freundlich吸附等温方程可以较好地描述D201树脂对植酸的等温吸附,表明吸附在常温下进行即可;D201树脂对植酸的吸附过程符合Lagergren一级速率方程,表观吸附速率常数k与植酸起始植酸浓度呈负相关关系,与温度呈正相关关系.在D201树脂对植酸的动态吸附与解吸过程中,层析柱管径、上样液浓度、上样液流速和洗脱剂流速对吸附与解吸效果影响较大.%The absorption and desorption properties of phytic acid on anion exchange resin were investigated through static and dynamic experiments. The results showed that D201 resin had the best exchange adsorption performance among all tested resins. The static absorption capacity of D201 resin reached 94. 54 mg/g when the pH value of phytic acid solution was adjusted to 2. 2, and sodium hydroxide solution of 1. 5 mol/L was beneficial to desorption. The absorption behavior of D201 resin for phytic acid obeyed the Freundlich adsorption isotherm equation, indicating that the absorption can be performed under normal temperature. The absorption kinetic data complied with Lagergren pseudo-first-order rate equation. The apparent adsorption rate k has a negative correlation with the initial concentration of phytic acid and has a positive correlation with temperature. As far as the dynamic absorption and desorption of phytic acid on D201 resin was concerned, the effects of chromatography column diameter, sample concentration, sample flowing velocity and eluant flowing velocity were notably observed.

  9. Cloning, expression, purification and characterization of tryptophan hydroxylase variants

    DEFF Research Database (Denmark)

    Boesen, Jane

    such as depression and obsessive-compulsive disorder (OCD). Characterization of TPH and elucidation of the enzymes regulation and catalytic mechanism is therefore vital to our understanding of the serotonin balance. This study concerns variants of both human TPH isoform 1 (hTPH1) and human TPH isoform...... 2 (h PH2). The main goal was to purify full-length hTPH1. Based on earlier results, hTPH1 was purified using detergent in the purification methods. After incubation of the hTPH1 sample with 0.1 % of n-dodecyl-β-D-maltopyranoside (DDM) the protein binds to the anion exchange column and elutes over a...

  10. HDAC-regulated myomiRs control BAF60 variant exchange and direct the functional phenotype of fibro-adipogenic progenitors in dystrophic muscles

    Science.gov (United States)

    Saccone, Valentina; Consalvi, Silvia; Giordani, Lorenzo; Mozzetta, Chiara; Barozzi, Iros; Sandoná, Martina; Ryan, Tammy; Rojas-Muñoz, Agustin; Madaro, Luca; Fasanaro, Pasquale; Borsellino, Giovanna; De Bardi, Marco; Frigè, Gianmaria; Termanini, Alberto; Sun, Xin; Rossant, Janet; Bruneau, Benoit G.; Mercola, Mark; Minucci, Saverio; Puri, Pier Lorenzo

    2014-01-01

    Fibro-adipogenic progenitors (FAPs) are important components of the skeletal muscle regenerative environment. Whether FAPs support muscle regeneration or promote fibro-adipogenic degeneration is emerging as a key determinant in the pathogenesis of muscular diseases, including Duchenne muscular dystrophy (DMD). However, the molecular mechanism that controls FAP lineage commitment and activity is currently unknown. We show here that an HDAC–myomiR–BAF60 variant network regulates the fate of FAPs in dystrophic muscles of mdx mice. Combinatorial analysis of gene expression microarray, genome-wide chromatin remodeling by nuclease accessibility (NA) combined with next-generation sequencing (NA-seq), small RNA sequencing (RNA-seq), and microRNA (miR) high-throughput screening (HTS) against SWI/SNF BAF60 variants revealed that HDAC inhibitors (HDACis) derepress a “latent” myogenic program in FAPs from dystrophic muscles at early stages of disease. Specifically, HDAC inhibition induces two core components of the myogenic transcriptional machinery, MYOD and BAF60C, and up-regulates the myogenic miRs (myomiRs) (miR-1.2, miR-133, and miR-206), which target the alternative BAF60 variants BAF60A and BAF60B, ultimately directing promyogenic differentiation while suppressing the fibro-adipogenic phenotype. In contrast, FAPs from late stage dystrophic muscles are resistant to HDACi-induced chromatin remodeling at myogenic loci and fail to activate the promyogenic phenotype. These results reveal a previously unappreciated disease stage-specific bipotency of mesenchimal cells within the regenerative environment of dystrophic muscles. Resolution of such bipotency by epigenetic intervention with HDACis provides a molecular rationale for the in situ reprogramming of target cells to promote therapeutic regeneration of dystrophic muscles. PMID:24682306

  11. Jeep variants

    CERN Document Server

    de Bondt, Michiel

    2010-01-01

    The jeep problem was first solved by O. Helmer and N.J. Fine. But not much later, C.G. Phipps formulated a more general solution. He formulated a so-called convoy or caravan variant of the jeep problem and reduced the original problem to it. The convoy idea of Phipps was refined in [3]. Here we will apply this refined idea to several variants of the jeep problem.

  12. Multi-Institutional FASTQ File Exchange as a Means of Proficiency Testing for Next-Generation Sequencing Bioinformatics and Variant Interpretation.

    Science.gov (United States)

    Davies, Kurtis D; Farooqi, Midhat S; Gruidl, Mike; Hill, Charles E; Woolworth-Hirschhorn, Julie; Jones, Heather; Jones, Kenneth L; Magliocco, Anthony; Mitui, Midori; O'Neill, Philip H; O'Rourke, Rebecca; Patel, Nirali M; Qin, Dahui; Ramos, Erica; Rossi, Michael R; Schneider, Thomas M; Smith, Geoffrey H; Zhang, Linsheng; Park, Jason Y; Aisner, Dara L

    2016-07-01

    Next-generation sequencing is becoming increasingly common in clinical laboratories worldwide and is revolutionizing clinical molecular testing. However, the large amounts of raw data produced by next-generation sequencing assays and the need for complex bioinformatics analyses present unique challenges. Proficiency testing in clinical laboratories has traditionally been designed to evaluate assays in their entirety; however, it can be alternatively applied to separate assay components. We developed and implemented a multi-institutional proficiency testing approach to directly assess custom bioinformatics and variant interpretation processes. Six clinical laboratories, all of which use the same commercial library preparation kit for next-generation sequencing analysis of tumor specimens, each submitted raw data (FASTQ files) from four samples. These 24 file sets were then deidentified and redistributed to five of the institutions for analysis and interpretation according to their clinically validated approach. Among the laboratories, there was a high rate of concordance in the calling of single-nucleotide variants, in particular those we considered clinically significant (100% concordance). However, there was significant discordance in the calling of clinically significant insertions/deletions, with only two of seven being called by all participating laboratories. Missed calls were addressed by each laboratory to improve their bioinformatics processes. Thus, through our alternative proficiency testing approach, we identified the bioinformatic detection of insertions/deletions as an area of particular concern for clinical laboratories performing next-generation sequencing testing. PMID:27155050

  13. Detection of variants of the pRAS3, pAB5S9, and pSN254 plasmids in Aeromonas salmonicida subsp. salmonicida: multidrug resistance, interspecies exchanges, and plasmid reshaping.

    Science.gov (United States)

    Vincent, Antony T; Trudel, Mélanie V; Paquet, Valérie E; Boyle, Brian; Tanaka, Katherine H; Dallaire-Dufresne, Stéphanie; Daher, Rana K; Frenette, Michel; Derome, Nicolas; Charette, Steve J

    2014-12-01

    The ubiquitous water-borne Gram-negative bacterium Aeromonas salmonicida subsp. salmonicida is the causative agent of furunculosis, a worldwide disease in fish farms. Plasmids carrying antibiotic resistance genes have already been described for this bacterium. The aim of the present study was to identify and characterize additional multidrug resistance plasmids in A. salmonicida subsp. salmonicida. We sequenced the plasmids present in two multiple antibiotic-resistant isolates using high-throughput technologies. We also investigated 19 other isolates with various multidrug resistance profiles by genotyping PCR and assessed their resistance to tetracycline. We identified variants of the pAB5S9 and pSN254 plasmids that carry several antibiotic resistance genes and that have been previously reported in bacteria other than A. salmonicida subsp. salmonicida, which suggests a high level of interspecies exchange. Genotyping analyses and the antibiotic resistance profiles of the 19 other isolates support the idea that multiple versions of pAB5S9 and pSN254 exist in A. salmonicida subsp. salmonicida. We also identified variants of the pRAS3 plasmid. The present study revealed that A. salmonicida subsp. salmonicida harbors a wide variety of plasmids, which suggests that this ubiquitous bacterium may contribute to the spread of antibiotic resistance genes in the environment. PMID:25267667

  14. Simultaneous determination of inorganic and organic anions by ion chromatography

    Energy Technology Data Exchange (ETDEWEB)

    Park, Yang Soon; Joe, Ki Soo; Han, Sun Ho; Park, Soon Dal; Choi, Kwang Soon

    1999-06-01

    Four methods were investigated for the simultaneous determination of several inorganic and organic anions in aqueous solution by ion chromatography. The first is two columns coupled system. The second is the gradient elution system with an anion exchange column. The third is the system with a mixed-mode stationary phase. The fourth is the system with an anion exchange column and the eluant of low conductivity without ion suppressor. The advantages and disadvantages of individual systems were discussed. The suitable methods were proposed for the application to the samples of the nuclear power industry and the environment. (author)

  15. Studies of anions sorption on natural zeolites.

    Science.gov (United States)

    Barczyk, K; Mozgawa, W; Król, M

    2014-12-10

    This work presents results of FT-IR spectroscopic studies of anions-chromate, phosphate and arsenate - sorbed from aqueous solutions (different concentrations of anions) on zeolites. The sorption has been conducted on natural zeolites from different structural groups, i.e. chabazite, mordenite, ferrierite and clinoptilolite. The Na-forms of sorbents were exchanged with hexadecyltrimethylammonium cations (HDTMA(+)) and organo-zeolites were obtained. External cation exchange capacities (ECEC) of organo-zeolites were measured. Their values are 17mmol/100g for chabazite, 4mmol/100g for mordenite and ferrierite and 10mmol/100g for clinoptilolite. The used initial inputs of HDTMA correspond to 100% and 200% ECEC of the minerals. Organo-modificated sorbents were subsequently used for immobilization of mentioned anions. It was proven that aforementioned anions' sorption causes changes in IR spectra of the HDTMA-zeolites. These alterations are dependent on the kind of anions that were sorbed. In all cases, variations are due to bands corresponding to the characteristic Si-O(Si,Al) vibrations (occurring in alumino- and silicooxygen tetrahedra building spatial framework of zeolites). Alkylammonium surfactant vibrations have also been observed. Systematic changes in the spectra connected with the anion concentration in the initial solution have been revealed. The amounts of sorbed CrO4(2-), AsO4(3-) and PO4(3-) ions were calculated from the difference between their concentrations in solutions before (initial concentration) and after (equilibrium concentration) sorption experiments. Concentrations of anions were determined by spectrophotometric method. PMID:25002191

  16. Online eluent-switching technique coupled anion-exchange liquid chromatography–ion trap tandem mass spectrometry for analysis of non-steroidal anti-inflammatory drugs in pig serum.

    Science.gov (United States)

    Chang, Kai Chun; Lin, Jyh Shiun; Cheng, Cheanyeh

    2015-11-27

    A novel method for online extraction, pH-gradient separation, and analysis of nine non-steroidal anti-inflammatory drugs (NSAIDs) was developed by coupling online eluent-switching technique to single anion-exchange chromatographic column/ion trap mass spectrometer (MS) and used for monitoring NSAIDs residues in pig serum. A neutral eluent and a pH-gradient eluent were used for extraction and separation of NSAIDs, respectively. Each of nine NSAIDs has an MS precursor ion of either [M−H]− or [M−Na]−. The extracted ion chromatogram for a specific product ion of each NSAID was used for its quantitative analysis. The dynamic linear ranges of calibration curves were all 0–200 ng mL−1 (R2 > 0.9950). The analysis accuracies estimated by spiking standard concentrations at 20, 100, and 200 ng mL−1 were 80.5–99.9%. The corresponding intra-day and inter-day precisions (RSD%) were 2.5–14.5% and 2.9–15.2%, respectively. The limit of detection/limit of quantitation of NSAIDs were 1.3/4.3, 0.5/1.6, 0.2/0.5, 2.5/8.2, 1.5/4.9, 0.6/2.1, 0.6/2.0, 0.5/1.7, and 0.6/2.1 ng mL−1 for carprofen, diclofenac, flunixin, ibuprofen, ketoprofen, meclofenamic acid sodium, mefenamic acid, niflumic acid, and tolfenamic acid, respectively. After 1 h injection of a dose containing 2 mg kg−1 weight pig of flunixin and tolfenamic acid to the pigs, a residue amount of 3480 ± 36 ng mL−1 and 431 ± 13 ng mL−1, respectively, was reached for the incurred pig serum specimens and both residues were reduced to about 20 ng mL−1 at the time of 24 h. PMID:26601710

  17. Highly active carbon supported palladium-rhodium PdXRh/C catalysts for methanol electrooxidation in alkaline media and their performance in anion exchange direct methanol fuel cells (AEM-DMFCs)

    International Nuclear Information System (INIS)

    Highlights: • Synthesis and physical evaluation of carbon supported, Rh containing Pd electrocatalysts. • Electroactivity towards methanol oxidation strongly enhanced in alkaline media. • Bimetallic catalyst show low CO oxidation and OH adsorption potentials. • CO2 current efficiency higher for bimetallic catalysts than for Pt/C or Pd/C. • Power density of 105 mW cm−2 for platinum-free alkaline direct methanol fuel cell. - Abstract: In this study carbon supported PdXRh electrocatalysts synthesized by wet chemical reduction process were tested for the potential use in anion-exchange membrane direct methanol fuel cells (AEM-DMFC) and compared to Pd/C and commercially available Pt/C. A metal loading of 20wt% on carbon was confirmed by thermogravimetric analysis (TGA) and catalyst compositions of PdRh3/C, PdRh/C and Pd3Rh/C were found via inductively coupled plasma optical emission spectroscopy (ICP-OES). Transmission electron microscopy (TEM) and x-ray diffraction (XRD) studies showed that the average particle and crystallite sizes of the PdXRh/C catalysts are in the range of 3.1 to 4.3 nm. It was also found that these catalysts are not alloyed. Cyclic voltammetry (CV) data reveals a 85–140 mV lower CH3OH oxidation onset potential and higher mass current densities for PdXRh/C catalysts compared with Pd/C. Steady-state measurements via chronoamperometry (CA) showed a good stability against poisoning during methanol oxidation and higher mass activities for PdRh/C and Pd3Rh/C compared to Pt/C. By using differential electrochemical mass spectrometry (DEMS) it was successfully shown that adding Rh to Pd results in an enhanced CO2 current efficiency (CCE) compared to Pd/C or Pt/C. AEM-DMFCs free from platinum were fabricated and single cell tests at 60 °C showed a significant increase of power density at 0.5 V cell potential from 4.8 mW cm−2 for Pd/C to 16.5 mW cm−2 for PdRh/C with the anode and cathode fed with 1 M methanol + 2 M KOH and synthetic air

  18. Separation of coagulation factor Ⅷ with high activity using gigaporous anion exchange chromatography%超大孔离子交换制备色谱分离纯化高活性凝血因子Ⅷ

    Institute of Scientific and Technical Information of China (English)

    康丽梅; 张焱; 罗坚; 李由; 周月芳; 余蓉; 苏志国

    2012-01-01

    建立了一条从人血浆中分离高活性凝血因子Ⅷ(FⅧ)的纯化工艺.基于FⅧ和介质孔径的尺度比及其对蛋白质活性影响的分析,设计了以超大孔离子交换制备色谱为核心步骤的新型分离纯化工艺.分别进行超大孔离子交换色谱与传统离子交换色谱的条件优化,并对优化工艺所得产品进行了活性检测(底物显色法)和纯度检测(高效凝胶过滤和凝胶电泳).结果表明,超大孔介质结构不但可以有效地保护蛋白质大分子结构,而且能够大幅度地提高制备色谱的传质速率,从而得到具有高凝血活性的FⅧ产品.FⅧ在超大孔制备色谱过程中的回收率(85%)比传统离子交换制备色谱高4~5倍,产品比活高达154 IU/mg.此外,还研究了超大孔介质的再生程序,采用5个柱体积的1mol/L NaOH低流速清洗色谱柱,保证了色谱工艺的稳定性.本纯化工艺步骤简单,重现性好,易于放大生产.%A purification process to obtain coagulation factor Vffl (FVI) with high activity from human plasma was established. Based on the analysis of the size ratio between FVi and matrix porous medium and its effect on the protein activity, a novel purification process designed was superporous ion exchange chromatography (IEC). The operating conditions of gigaporous and traditional anion exchange chromatography were optimized separately. The chromogenic substrate , gel filtration and sodium dodecyl sulfate-polyacrylamide gel electrophoresis ( SDS-PAGE) were used to monitor the bioactivity and purity of the chromatographic products. The results showed that the superporous medium could not only protect structure of macro-protein but also enhance its mass transfer, finally giving FVI product with high activity. The yield of FVM in superporous chromatography was about five times of commercially agarose chromatography and the specific activity was up to 154 IU/mg protein. Furthermore, we studied the regeneration process of

  19. Anion retention in soil: Possible application to reduce migration of buried technetium and iodine

    Energy Technology Data Exchange (ETDEWEB)

    Schulz, R.K.; Duckart, E.C. (California Univ., Berkeley, CA (United States). Dept. of Soil Science); O' Donnell, E. (Nuclear Regulatory Commission, Washington, DC (United States))

    1992-12-01

    Before testing the performance characteristics of andisols for retention of anions in the near-field environment of Low Level Wastes (LLW) disposal facilities it is necessary to locate one or more sufficiently extensive bodies of natural soil with the highest possible natural anion exchange capacity. For this purpose we developed a rugged, portable semiquantitative field test for anion exchange capacity based on short-term sorption of iodide by soil samples. We validated the iodide sorption field test against a well established quantitative laboratory test based on anion exchange of chloride and nitrate, then carried out an initial survey of volcanic terrain in northern California using the field test.

  20. Controlled Release Kinetics in Hydroxy Double Salts: Effect of Host Anion Structure

    OpenAIRE

    Stephen Majoni; Jeanne M. Hossenlopp

    2014-01-01

    Nanodimensional layered metal hydroxides such as layered double hydroxides (LDHs) and hydroxy double salts (HDSs) can undergo anion exchange reactions releasing intercalated anions. Because of this, these metal hydroxides have found applications in controlled release delivery of bioactive species such as drugs and pesticides. In this work, isomers of hydroxycinnamate were used as model compounds to systematically explore the effects of anion structure on the rate and extent of anion release i...

  1. A new family of anionic organic–inorganic hybrid doughnut-like nanostructures

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Zhuxiu; Gao, Wen-Yang; Wojtas, Lukasz; Zhang, Zhenjie; Zaworotko, Michael J. (Limerick); (USF)

    2015-06-15

    A family of soluble organic–inorganic hybrid doughnut-like anions, hydoughnuts, has been prepared by the self-assembly of polyoxovanadate anions and 1,3-benzenedicarboxylate (bdc) linkers. Derivatives of the parent hydoughnut, [(V₄O₈Cl)₄(bdc)₈]⁴⁻, can be obtained by changing the counter-ion or by using a variant of bdc.

  2. Intrinsic anion oxidation potentials.

    Science.gov (United States)

    Johansson, Patrik

    2006-11-01

    Anions of lithium battery salts have been investigated by electronic structure calculations with the objective to find a computational measure to correlate with the observed (in)stability of nonaqueous lithium battery electrolytes vs oxidation often encountered in practice. Accurate prediction of intrinsic anion oxidation potentials is here made possible by computing the vertical free energy difference between anion and neutral radical (Delta Gv) and further strengthened by an empirical correction using only the anion volume as a parameter. The 6-311+G(2df,p) basis set, the VSXC functional, and the C-PCM SCRF algorithm were used. The Delta Gv calculations can be performed using any standard computational chemistry software. PMID:17078600

  3. A procedure for reducing the concentration of hydrogen ions in acid anionic eluate and equipment therefore

    International Nuclear Information System (INIS)

    The method is described of reducing the concentration of hydrogen ions in acid anionic eluate produced in the separation of uranium or other metals, in which anion exchanger elution, precipitation, filtration and precipitate and anion exchanger washing are used. The technological line for such elution comprises at least one ion exchange column and at least one container. They together form the first and the second stages of preparation of the acid anion elution solution, the sorption-elution separation of hydrogen ions on an cation exchanger being inserted between them. The preparation of the solution is divide into two stages. In the first stage, the acid and part of the solution for the preparation of the acid anion elution solution are supplied. The resulting enriched acid elution solution is fe onto the cation exchanger where the hydrogen ion concentration i reduced. It is then carried into the second stage where it is mixed with the remaining part of the solution. (B.S.)

  4. Method of decomposing radioactive spent ion exchange resins

    International Nuclear Information System (INIS)

    Purpose: To improve the decomposability of spent ion exchange resins such as anionic resins, anionic - cationic mixed resins or the likes issued from nuclear power plants. Method: Spent ion exchange resins containing radioactive materials are decomposed by hydrogen peroxide. In this case, anionic exchange resins or mixture of anionic exchange resins and cationic exchange resins are decomposed by using bivalent or trivalent iron ions coexistent with sulfate groups in excess of the amount corresponding to the molar amount of bivalent or trivalent iron ions as a catalyst. Since the anionic exchange resins or the mixture of the anionic exchange resins and cationic resins are decomposed substantially completely, the amount of residue after the decomposition is reduced and the volume-reducing property of the radioactive wastes can be improved to facilitate the solidifying treatment. (Moriyama, K.)

  5. Competing Noncovalent Host-guest Interactions and H/D Exchange: Reactions of Benzyloxycarbonyl-Proline Glycine Dipeptide Variants with ND3

    Science.gov (United States)

    Miladi, Mahsan; Olaitan, Abayomi D.; Zekavat, Behrooz; Solouki, Touradj

    2015-11-01

    A combination of density functional theory calculations, hydrogen/deuterium exchange (HDX) reactions, ion mobility-mass spectrometry, and isotope labeling tandem mass spectrometry was used to study gas-phase "host-guest" type interactions of a benzyloxycarbonyl (Z)-capped proline (P) glycine (G) model dipeptide (i.e., Z-PG) and its various structural analogues with ND3. It is shown that in a solvent-free environment, structural differences between protonated and alkali metal ion (Na+, K+, or Cs+)-complexed species of Z-PG affect ND3 adduct formation. Specifically, [Z-PG + H]+ and [Z-PG-OCH3 + H]+ formed gas-phase ND3 adducts ([Z-PG (or Z-PG-OCH3) + H + ND3]+) but no ND3 adducts were observed for [Z-PG + alkali metal]+ or [Z-PG + H - CO2]+. Experimentally measured and theoretically calculated collision cross sections (CCSs) of protonated and alkali metal ion-complexed Z-PG species showed similar trends that agreed with the observed structural differences from molecular modeling results. Moreover, results from theoretical ND3 affinity calculations were consistent with experimental HDX observations, indicating a more stable ND3 adduct for [Z-PG + H]+ compared to [Z-PG + alkali metal]+ species. Molecular modeling and experimental MS results for [Z-PG + H]+ and [Z-PG + alkali metal]+ suggest that optimized cation-π and hydrogen bonding interactions of carbonyl groups in final products are important for ND3 adduct formation.

  6. 2-Methyl-2-Pentenal Prepared From Condensation of   Propionaldhyde in Presence of Anion Exchange Resin%阴离子交换树脂催化丙醛缩合制备2-甲基-2-戊烯醛

    Institute of Scientific and Technical Information of China (English)

    唐斯萍; 李谦和; 尹笃林

    2001-01-01

    研究了丙醛双分子缩合制2-甲基-2-戊烯醛的反应,以阴离子交换树脂作催化剂,重点考察了反应温度、反应时间、阴离子交换树脂/丙醛(摩尔比)、溶剂用量对目标产物2-甲基-2-戊烯醛产率的影响,确定了制备2-甲基-2-戊烯醛的优化反应条件:温度30℃,时间2h,阴离子交换树脂/丙醛10mmol/20mmol,溶剂苯5mL,目标产物2-甲基-2-戊烯醛的产率可达93.54%.%In this paper we studied the synthesis of 2-methyl-2-pentenalfrom self-aldol condensation of propionaldhyde, with anion exchange resin as the catalyst of the condensation.The optimum conditions were established: reaction temperature is 30 ℃, reaction time is 2 h ,the dose of benzene as the solvent is 5 mL, anion exchange resin: CH3CH2CHO= 10 mmol/20 mmol, and 2-methyl-2-pentenal can be obtained with 93.54% yield.

  7. Supramolecular Chemistry of Selective Anion Recognition for Anions of Environmental Relevance

    International Nuclear Information System (INIS)

    The major thrust of this project, led by the University of Kansas (Prof. Kristin Bowman-James), entails an exploration of the basic determinants of anion recognition and their application to the design, synthesis, and testing of novel sulfate extractants. A key scientific inspiration for the work comes from the need, codified in simple-to-appreciate terms by the Oak Ridge National Laboratory component of the team (viz. Dr. Bruce Moyer), for chemical entities that can help in the extractive removal of species that have low solubilities in borosilicate glass. Among such species, sulfate anion, has been identified as particularly insidious. Its presence interferes with the vitrification process, thus rendering the remediation of tank waste from, e.g., the Hanford site far more difficult and expensive. The availability of effective extractants, that would allow for the separation of separating sulfate from the major competing anions in the waste, especially nitrate, could allow for pre-vitrification removal of sulfate via liquid-liquid extraction. The efforts at The University of Texas, the subject of this report, have thus concentrated on the development of new sulfate receptors. These systems are designed to increase our basic understanding of anion recognition events and set the stage for the development of viable sulfate anion extractants. In conjunction with the Oak Ridge National Laboratory (ORNL) members of the research team, several of these new receptors were studied as putative extractants, with two of the systems being shown to act as promising synergists for anion exchange.

  8. Anion-π catalysis.

    Science.gov (United States)

    Zhao, Yingjie; Beuchat, César; Domoto, Yuya; Gajewy, Jadwiga; Wilson, Adam; Mareda, Jiri; Sakai, Naomi; Matile, Stefan

    2014-02-01

    The introduction of new noncovalent interactions to build functional systems is of fundamental importance. We here report experimental and theoretical evidence that anion-π interactions can contribute to catalysis. The Kemp elimination is used as a classical tool to discover conceptually innovative catalysts for reactions with anionic transition states. For anion-π catalysis, a carboxylate base and a solubilizer are covalently attached to the π-acidic surface of naphthalenediimides. On these π-acidic surfaces, transition-state stabilizations up to ΔΔGTS = 31.8 ± 0.4 kJ mol(-1) are found. This value corresponds to a transition-state recognition of KTS = 2.7 ± 0.5 μM and a catalytic proficiency of 3.8 × 10(5) M(-1). Significantly increasing transition-state stabilization with increasing π-acidity of the catalyst, observed for two separate series, demonstrates the existence of "anion-π catalysis." In sharp contrast, increasing π-acidity of the best naphthalenediimide catalysts does not influence the more than 12 000-times weaker substrate recognition (KM = 34.5 ± 1.6 μM). Together with the disappearance of Michaelis-Menten kinetics on the expanded π-surfaces of perylenediimides, this finding supports that contributions from π-π interactions are not very important for anion-π catalysis. The linker between the π-acidic surface and the carboxylate base strongly influences activity. Insufficient length and flexibility cause incompatibility with saturation kinetics. Moreover, preorganizing linkers do not improve catalysis much, suggesting that the ideal positioning of the carboxylate base on the π-acidic surface is achieved by intramolecular anion-π interactions rather than by an optimized structure of the linker. Computational simulations are in excellent agreement with experimental results. They confirm, inter alia, that the stabilization of the anionic transition states (but not the neutral ground states) increases with the π-acidity of the

  9. Vanadogermanate cluster anions.

    Science.gov (United States)

    Whitfield, T; Wang, X; Jacobson, A J

    2003-06-16

    Three novel vanadogermanate cluster anions have been synthesized by hydrothermal reactions. The cluster anions are derived from the (V(18)O(42)) Keggin cluster shell by substitution of V=O(2+) "caps" by Ge(2)O(OH)(2)(4+) species. In Cs(8)[Ge(4)V(16)O(42)(OH)(4)].4.7H(2)O, 1, (monoclinic, space group C2/c (No. 15), Z = 8, a = 44.513(2) A, b = 12.7632(7) A, c = 22.923(1) A, beta = 101.376(1) degrees ) and (pipH(2))(4)(pipH)(4)[Ge(8)V(14)O(50).(H(2)O)] (pip = C(4)N(2)H(10)), 2 (tetragonal, space group P4(2)/nnm (No. 134), Z = 2, a = 14.9950(7) A, c = 18.408(1) A), two and four VO(2+) caps are replaced, respectively, and each cluster anion encapsulates a water molecule. In K(5)H(8)Ge(8)V(12)SO(52).10H(2)O, 3, (tetragonal, space group I4/m (No. 87), Z = 2, a = 15.573(1) A, c = 10.963(1) A), four VO(2+) caps are replaced by Ge(2)O(OH)(2)(4+) species, and an additional two are omitted. The cluster ion in 3 contains a sulfate anion disordered over two positions. The cluster anions are analogous to the vanadoarsenate anions [V(18)(-)(n)()As(2)(n)()O(42)(X)](m)(-) (X = SO(3), SO(4), Cl; n = 3, 4) previously reported. PMID:12793808

  10. 人红细胞阴离子交换蛋白1在胃癌靶向治疗应用中的研究进展%Progression of targeted therapy of anion exchanger 1 for gastric cancer

    Institute of Scientific and Technical Information of China (English)

    傅国辉; 王婷; 索文昊

    2012-01-01

    胃癌位居我国恶性肿瘤死因的第二位.95%以上的胃癌为腺癌,对放疗和化疗都不敏感;已发生转移的胃癌5年生存率仅15%~ 20%.因此,寻求有效的早期诊断和靶向治疗方法一直是胃癌研究关注的焦点.该课题组在对人红细胞阴离子交换蛋白1(AE1)的研究中发现,AE1除特异表达在红细胞膜外,在胃癌细胞质中具有83%的高频率表达.AE1的异常表达与碱性环境下 p65/miR-24负反馈调控失衡相关.胃上皮细胞内缺乏AE1上膜途径导致AE1表达后大量滞留于细胞质中,胞质内的AE1通过几个相互关联的信号通路参与肿瘤的发生发展进程,主要包括:①与肿瘤抑制蛋白p16直接相互作用,扣押后者在胞质而不能入核发挥细胞周期负调控作用;②妨碍另一家族成员AE2正常上膜,加速AE2降解,进一步促进细胞碱化和Wnt/β-catenin通路活化.这一研究成果已被收录在Atlas of Genetics and Cytogenetics in Oncology and Haematology中.明确了AE1是胃癌分子标志物,在此基础上,课题组在细胞及动物水平开展了针对AE1的胃癌靶向治疗研究.结果显示,靶向AE1可以有效抑制胃癌细胞增殖,能够使药物诱发的小鼠胃癌检出率由62% ~ 70%降低到15.8%.AE1蛋白作为胃癌诊断和治疗的靶标具有非常重要的应用价值.%Gastric cancer is the second leading cause of cancer-related death in China. Gastric adenocarcinoma comprises 95% of the totaL number of gastric malignancies which is often insensitive to chemo- and radiation therapy, and the 5-year survival rate of patients is only 15% -20%. Therefore, majority of studies have focused on early diagnosis and targeted therapy of gastric cancer. Our studies have found that human anion exchanger 1 ( AE1) , an erythrocyte membrane protein, is unexpectedly expressed in the gastric cancer with 83% frequency. Failure in negative feedback regulation between p65 and miR-24 is involved in aberrant

  11. Selective Adsorption and Separation of Salicylic Acid and Phenol by 717 Anion Exchange Resin%717阴离子交换树脂选择吸附分离水杨酸和苯酚

    Institute of Scientific and Technical Information of China (English)

    谢祖芳; 童张法; 陈渊; 晏全; 李凤; 吴燕平

    2011-01-01

    The anion exchange resin 717 was used to selectively adsorb and separate the salicylic acid and phenol from their binary aqueous solution. The adsorption behavior of 717 resin for each adsorbate was studied via both dynamic and static methods. The effects of pH value, adsorbate concentration and adsorption time on the adsorption process were investigated, and the isotherm adsorption and adsorption kinetics were also studied.The experimental results show that the pH value of the solution plays the most important role in the adsorption and separation process. At pH of 4.5, the existence of phenol in the solution essentially does not affect the salicylic acid adsorption of the 717 resin, while when the pH is 11, the phenol can be adsorbed by 717 resin to substitute the adsorbed salicylic acid on it, which substantially decreases the salicylic acid adsorption capacity of the resin. In the pH range of 4~8, the 717 resin has very high selective adsorption ability and adsorption capacity for the salicylic acid, and its adsorption capacity for salicylic acid is more than an order of magnitude larger than that for the phenol. With such high adsorption selectivity, the 717 resin is favorable to be used for the separation salicylic acid from the binary aqueous solution of salicylic acid and phenol. The static adsorptions show that the adsorptions of salicylic acid and phenol by 717 resin are in accordance with Freundlieh isotherm model, and the adsorption kinetics data fit well with the Lagergren pseudo-first order rate equation. Dynamic adsorption of the mixed binary aqueous solution of salicylic acid and phenol by 717 resin shows that, in a column with resin of 1.5 g, the first 475 mL of the exit water after adsorption contains essentially only the phenol because almost all the salicylic acid are adsorbed by the resin. It was found that the salicylic acid adsorbed on the resin can be easily eluted by the 5%NaCl+2%NaOH solution at room temperature.%用717阴离子交

  12. Anion Ordering in Bichalcogenides

    Directory of Open Access Journals (Sweden)

    Martin Valldor

    2016-07-01

    Full Text Available This review contains recent developments and new insights in the research on inorganic, crystalline compounds with two different chalcogenide ions (bichalcogenides. Anion ordering is used as a parameter to form structural dimensionalities as well as local- and global-electric polarities. The reason for the electric polarity is that, in the heterogeneous bichalcogenide lattice, the individual bond-lengths between cations and anions are different from those in a homogeneous anion lattice. It is also shown that heteroleptic tetrahedral and octahedral coordinations offer a multitude of new crystal fields and coordinations for involved cations. This coordination diversity in bichalcogenides seems to be one way to surpass electro-chemical redox potentials: three oxidation states of a single transition metal can be stabilized, e.g., Ba15V12S34O3. A new type of disproportionation, related to coordination, is presented and results from chemical pressure on the bichalcogenide lattices of (La,CeCrS2O, transforming doubly [CrS3/3S2/2O1/1]3− (5+1 into singly [CrS4/2S2/3]7/3− (6+0 and [CrS4/3O2/1]11/3− (4+2 coordinations. Also, magnetic anisotropy is imposed by the anion ordering in BaCoSO, where magnetic interactions via S or O occur along two different crystallographic directions. Further, the potential of the anion lattice is discussed as a parameter for future materials design.

  13. Studies on transport of anionic plutonium complex from nitric acid medium across ALIQUAT 336/N-dodecane liquid membrane

    International Nuclear Information System (INIS)

    Aliquat 336 is quaternary ammonium salt and its large organic cation is associated with chloride ion. It forms complexes with anions with wider range of acidity/pH and it works as anion exchanger. In the PUREX process, plutonium product solution is chemically conditioned to all plutonium into fourth valence state by addition of suitable amount of 13 M HNO3. The extraction of anionic complex of plutonium by Aliquat 336 is affected by anion exchange mechanism. This extraction mechanism is in resemblance with the ion exchange method used for purification and concentration of plutonium in the PUREX process

  14. Anion retention in soil: Possible application to reduce migration of buried technetium and iodine. Development of a field test

    Energy Technology Data Exchange (ETDEWEB)

    Schulz, R.K.; Duckart, E.C. [California Univ., Berkeley, CA (United States). Dept. of Soil Science; O`Donnell, E. [Nuclear Regulatory Commission, Washington, DC (United States)

    1992-12-01

    Before testing the performance characteristics of andisols for retention of anions in the near-field environment of Low Level Wastes (LLW) disposal facilities it is necessary to locate one or more sufficiently extensive bodies of natural soil with the highest possible natural anion exchange capacity. For this purpose we developed a rugged, portable semiquantitative field test for anion exchange capacity based on short-term sorption of iodide by soil samples. We validated the iodide sorption field test against a well established quantitative laboratory test based on anion exchange of chloride and nitrate, then carried out an initial survey of volcanic terrain in northern California using the field test.

  15. Migraine Variants in Children

    Science.gov (United States)

    ... headaches . Home > Migraine Variants in Children Print Email Migraine Variants in Children ACHE Newsletter Sign up for ... newsletter by entering your e-mail address below. Migraine Variants in Children There are several disorders that ...

  16. Porating anion-responsive copolymeric gels.

    Science.gov (United States)

    England, Dustin; Yan, Feng; Texter, John

    2013-09-24

    A polymerizable ionic liquid surfactant, 1-(11-acryloyloxyundecyl)-3-methylimidiazolium bromide (ILBr), was copolymerized with methyl methacrylate (MMA) in aqueous microemulsions at 30% (ILBr w/w) and various water to MMA ratios. The ternary phase diagram of the ILBr/MMA/water system was constructed at 25 and 60 °C. Homopolymers and copolymers of ILBr and MMA were produced by thermally initiated chain radical microemulsion polymerization at various compositions in bicontinuous and reverse microemulsion subdomains. Microemulsion polymerization reaction products varied from being gel-like to solid, and these materials were analyzed by thermal and scanning electron microscopy methods. Microemulsion polymerized materials were insoluble in all solvents tested, consistent with light cross-linking. Ion exchange between Br(-) and PF6(-) in these copolymeric materials resulted in the formation of open-cell porous structures in some of these materials, as was confirmed by scanning electron microscopy (SEM). Several compositions illustrate the capture of prepolymerization nanoscale structure by thermally initiated polymerization, expanding the domain of compositions exhibiting this feat and yet to be demonstrated in any other system. Regular cylindrical pores in interpenetrating ILBr-co-MMA and PMMA networks are produced by anion exchange in the absence of templates. A percolating cluster/bicontinuous transition is "captured" by SEM after using anion exchange to visualize the mixed cluster/pore morphology. Some design principles for achieving this capture and for obtaining stimuli responsive solvogels are articulated, and the importance of producing solvogels in capturing the nanoscale is highlighted. PMID:23968242

  17. Flow injection determination of selenium by successive retention of Se(IV) and tetrahydroborate(III) on an anion-exchange resin and hydride generation electrothermal atomization atomic absorption spectrometry with in-atomizer trapping. Part 1. Method development and investigation of interferences

    Science.gov (United States)

    Carrero, Pablo E.; Tyson, Julian F.

    1998-12-01

    A sample solution was passed at 20 ml min -1 through a column (150×4 mm 2) of Amberlite IRA-410Stron anion-exchange resin for 60 s. After washing, a solution of 0.1% sodium borohydride was passed through the column for 60 s at 5.1 ml min -1. Following a second wash, a solution of 8 mol l -1 hydrochloric acid was passed at 5.1 ml min -1 for 45 s. The hydrogen selenide was stripped from the eluent solution by the addition of an argon flow at 150 ml min -1 and the bulk phases were separated by a glass gas-liquid separator containing glass beads. The gas stream was dried by passing through a Nafion® dryer and fed, via a quartz capillary tube, into the dosing hole of a transversely heated graphite cuvette containing an integrated L'vov platform which had been pretreated with 120 μg of iridium as trapping agent. The furnace was held at a temperature of 250°C during this trapping stage and then stepped to 2000°C for atomization. The calibration was performed with aqueous standards solution of selenium (selenite, SeO 32-) with quantification by peak area. A number of experimental parameters, including reagent flow rates and composition., nature of the gas-liquid separator, nature of the anion-exchange resin, column dimensions, argon flow rate and sample pH, were optimized. The effects of a number of possible interferents, both anionic and cationic were studies for a solution of 500 ng 1 -1 of selenium. The most severe depressions were caused by iron (III) and mercury (II) for which concentrations of 20 and 10 mg 1 -1 caused a 5% depression on the selenium signal. For the other cations (cadmium, cobalt, copper, lead,. magnesium, and nickel) concentrations of 50-70 mg 1 -1 could be tolerated. Arsenate interfered at a concentration of 3 mg -1, whereas concentrations of chloride, bromide, iodide, perchlorate, and sulfate of 500-900 mg l -1 could be tolerated. A linear response was obtained between the detection limit of 4 ng 1 -1, with a characteristic mass of 130 pg. The

  18. Anion concurrence and anion selectivity in the sorption of radionuclides by organotones

    International Nuclear Information System (INIS)

    Some long-lived and radiologically important nuclear fission products, such as I-129 (half-life t1/2 = 1,6 . 107 a), Tc-99 (t1/2 = 2,1 . 105 a), and Se-79 (t1/2 = 6,5 . 104 a) are anionic in aqueous environments. This study focuses on the adsorption of such anions to organoclays and the understanding of the selectivity of the process. The organoclays used in this study were prepared from a bentonite (MX-80) and a vermiculite clay, and the cationic surfactants hexadcylpyridium, hexadecyltrimethylammonium, and benzethonium. Surfactant adsorption to the bentonite exceeds the cation exchange capacity of the clay, with the surplus positive charge being balanced by the co-adsorption of chloride. The interlayer distance of the bentonites is increased sufficiently to contain bi- and pseudotrimolecular structures of the surfactants. Adsorption experiments were carried out using the batch technique. Anion adsorption of iodide, perrhenate, selenite, nitrate, and sulphate is mainly due to ion exchange with chloride. As an additional adsorption mechanism, the incorporation of inorganic ion pairs into the interlayer space of the clay is proposed as a result of experiments showing differences in the adsorption levels of sodium and potassium iodide. Anion adsorption results show a clear selectivity of the organoclays, with the affinity sequence being: ReO-4 > I- > NO-3 > Cl- > SO2-4 > SeO2-3. This sequence corresponds to the sequence of increasing hydration energies of the anions, thus selectivity could be due to the process of minimization of free energy of the system. (orig.)

  19. Functional Block Copolymers via Anionic Polymerization for Electroactive Membranes

    OpenAIRE

    Schultz, Alison

    2013-01-01

           Ion-containing block copolymers blend ionic liquid properties with well-defined polymer architectures. This provides conductive materials with robust mechanical stability, efficient processability, and tunable macromolecular design. Conventional free radical polymerization and anion exchange achieved copolymers containing n-butyl acrylate and phosphonium ionic liquids. These compositions incorporated vinylbenzyl triphenyl phosphonium and vinylbenzyl tricyclohexyl phosphonium cations be...

  20. Modeling Donnan Dialysis Separation for Carboxylic Anion Recovery

    DEFF Research Database (Denmark)

    Prado Rubio, Oscar Andres; Møllerhøj, Martin; Jørgensen, Sten Bay;

    2010-01-01

    dynamic model for transport of multiple ions through an anion exchange membrane is derived based on an irreversible thermodynamics approach. This model accounts for the convective transport of the dissociated and undissociated species in the channels with diffusion and migration across the bounda...

  1. Effects of ionizing radiation on modern ion exchange materials

    Energy Technology Data Exchange (ETDEWEB)

    Marsh, S.F.; Pillay, K.K.S.

    1993-10-01

    We review published studies of the effects of ionizing radiation on ion exchange materials, emphasizing those published in recent years. A brief overview is followed by a more detailed examination of recent developments. Our review includes styrene/divinylbenzene copolymers with cation-exchange or anion-exchange functional groups, polyvinylpyridine anion exchangers, chelating resins, multifunctional resins, and inorganic exchangers. In general, strong-acid cation exchange resins are more resistant to radiation than are strong-base anion exchange resins, and polyvinylpyridine resins are more resistant than polystyrene resins. Cross-linkage, salt form, moisture content, and the surrounding medium all affect the radiation stability of a specific exchanger. Inorganic exchangers usually, but not always, exhibit high radiation resistance. Liquid ion exchangers, which have been used so extensively in nuclear processing applications, also are included.

  2. Effects of ionizing radiation on modern ion exchange materials

    International Nuclear Information System (INIS)

    We review published studies of the effects of ionizing radiation on ion exchange materials, emphasizing those published in recent years. A brief overview is followed by a more detailed examination of recent developments. Our review includes styrene/divinylbenzene copolymers with cation-exchange or anion-exchange functional groups, polyvinylpyridine anion exchangers, chelating resins, multifunctional resins, and inorganic exchangers. In general, strong-acid cation exchange resins are more resistant to radiation than are strong-base anion exchange resins, and polyvinylpyridine resins are more resistant than polystyrene resins. Cross-linkage, salt form, moisture content, and the surrounding medium all affect the radiation stability of a specific exchanger. Inorganic exchangers usually, but not always, exhibit high radiation resistance. Liquid ion exchangers, which have been used so extensively in nuclear processing applications, also are included

  3. Chemical stability of hydroxysulphate green rust synthetised in the presence of foreign anions: carbonate, phosphate and silicate

    Energy Technology Data Exchange (ETDEWEB)

    Ruby, C., E-mail: ruby@lcpme.cnrs-nancy.fr; Gehin, A.; Aissa, R.; Ghanbaja, J.; Abdelmoula, M.; Genin, J.-M. R. [UMR 7564 CNRS-Universite Henri Poincare-Nancy 1, Equipe Microbiologie et Physique and Departement Materiaux et Structures, Laboratoire de Chimie Physique et Microbiologie pour l' Environnement (France)

    2006-01-15

    Hydroxysulphate green rust {l_brace}GR(SO{sub 4}{sup 2-}){r_brace} species were precipitated in the presence of various anions. GR(SO{sub 4}{sup 2-}) is stable at {approx}pH 7 and is transformed into a mixture of magnetite and ferrous hydroxide when the pH raised at {approx}12. In the presence of carbonate species, GR(SO{sub 4}{sup 2-}) is partially transformed into a mixture of magnetite and siderite at {approx}pH 8.5. This transformation is stopped when silicate anions are present in the solution. As already observed for phosphate anions, the adsorption of silicate anions on the lateral faces of the GR(SO{sub 4}{sup 2-}) crystals may explain this stabilization effect. Sulphate anions are easily exchanged by carbonate species at {approx}pH 10.5. In contrast, anionic exchange between sulphate and phosphate anions was not observed.

  4. Resonant spectra of quadrupolar anions

    CERN Document Server

    Fossez, K; Nazarewicz, W; Michel, N; Garrett, W R; Płoszajczak, M

    2016-01-01

    In quadrupole-bound anions, an extra electron is attached at a sufficiently large quadrupole moment of a neutral molecule, which is lacking a permanent dipole moment. The nature of the bound states and low-lying resonances of such anions is of interest for understanding the threshold behavior of open quantum systems in general. In this work, we investigate the properties of quadrupolar anions as extreme halo systems, the formation of rotational bands, and the transition from a subcritical to supercritical electric quadrupole moment. We solve the electron-plus-molecule problem using a non-adiabatic coupled-channel formalism by employing the Berggren ensemble, which explicitly contains bound states, narrow resonances, and the scattering continuum. We demonstrate that binding energies and radii of quadrupolar anions strictly follow the scaling laws for two-body halo systems. Contrary to the case of dipolar anions, ground-state band of quadrupolar anions smoothly extend into the continuum, and many rotational ban...

  5. Bound anionic states of adenine

    OpenAIRE

    Harańczyk, Maciej; Gutowski, Maciej; Li, Xiang; Bowen, Kit H.

    2007-01-01

    Anionic states of nucleic acid bases are involved in DNA damage by low-energy electrons and in charge transfer through DNA. Previous gas phase studies of free, unsolvated nucleic acid base parent anions probed only dipole-bound states, which are not present in condensed phase environments, but did not observe valence anionic states, which for purine bases are thought to be adiabatically unbound. Contrary to this expectation, we have demonstrated that some thus far ignored tautomers of adenine...

  6. Preparation of anionic clay-birnessite manganese oxide composites by interlayer oxidation of oxalate ions by permanganate

    Science.gov (United States)

    Arulraj, James; Rajamathi, Michael

    2013-02-01

    Oxalate intercalated anionic clay-like nickel zinc hydroxysalt was obtained starting from nickel zinc hydroxyacetate, Ni3Zn2(OH)8(OAc)2·2H2O, by anion exchange. The intercalated oxalate species was reacted with potassium permanganate in such a way that the layered manganese oxide formed was within the interlayer region of the anionic clay resulting in a layered composite in which the negative charges on the birnessite type manganese oxide layers compensate the positive charges on the anionic clay layers. Birnessite to anionic clay ratio could be varied by varying the reaction time or the amount of potassium permanganate used.

  7. Procedure for reducing hydrogen ion concentration in acidic anion eluate

    International Nuclear Information System (INIS)

    A procedure is suggested for reducing the concentration of hydrogen ions in the acidic anionic eluate formed during the separation of uranium. The procedure involves anex elution, precipitation, filtration, precipitate rinsing, and anex rinsing. The procedure is included in the uranium elution process and requires at least one ion exchanger column and at least one tank in the continuous or discontinuous mode. Sparing the neutralizing agent by reducing the hydrogen ion concentration in the acidic anionic eluate is a major asset of this procedure. (Z.S.). 1 fig

  8. Recovery of niobium anions from aqueous solutions by ion flotation

    International Nuclear Information System (INIS)

    In principle the feasibility of recovering niobates (K2NbOF5 and K2NbF7) from aqueous media by ion flotation was established. When using quaternary ammonium bases or amines as the collectors, the optimal conditions lie in the interval pH = 5.0-9.0. The interaction of niobates with cationic surfactants may proceed through an anion-exchange mechanism. The presence of acid in the solution suppresses this interaction, owing to the competition from the anions that are present and owing to binding of the surface-active collectors into a complex. 3 figures

  9. Separation of Fe using a small amount of AG1-X4 anion exchange resin and Fe isotope compositions of Geological Reference Materials%少量AG1-X4阴离子交换树脂分离地质标样中的铁及铁同位素测定

    Institute of Scientific and Technical Information of China (English)

    唐索寒; 闫斌; 李津

    2013-01-01

      报道了利用少量 AG1-X4阴离子交换树脂分离地质样品中 Fe 及测定 Fe 同位素的方法。对少量AG1-X4和AG MP-1树脂的分离效果进行了比较,测定了经过AG1-X4分离后的地质标样BCR-2、BHVO-2、BIR-1a、AGV-2、W-2、GSP-2、COQ-1、DTS-2b、JB-2、Jsd-1、GBW07105和 GBW07267的 Fe 同位素组成,其结果与文献参考值在误差范围内一致。这些数据的发表对于地质样品Fe的化学分离和同位素测定提供了参考依据。此方法可以大大减少化学试剂用量,是一种快速有效分离铁的方法。%AG MP-1 anion exchange resin has been reported to be an effective chromatographic technique choice for the complete separation of Cu, Fe and Zn in geological samples. In the cases of Fe being the only interested element, AG1-X4 showed better separation efficiencies. In this work, an effective Fe separation procedure has been successfully established using small amount of AG1-X4 anion exchange resin, aiming to speed up separation, to reduce consumption of regents and to lower down the regent background. Comparison with AG MP-1 has been also made. Fe isotope compositions have been measured on geological reference materials, namely BCR-2, BHVO-2, BIR-1a, AGV-2, W-2, GSP-2, COQ-1, DTS-2b from USGS (United States Geological Survey), JB-2, Jsd-1 from GSJ (Geological Survey of Japan) as well as GBW07105 and GBW07267 from RMRC (National standard reference materials research center). With the analytical results being identical with those reported values within analytical errors, the described separation method and reported data set may serve as valuable references for iron isotopic studies.

  10. Chemical Modeling of Cometary Anions

    Science.gov (United States)

    Cordiner, Martin; Charnley, S. B.

    2009-09-01

    The presence of negative ions (anions) in cometary comae is known from Giotto mass spectrometry of 1P/Halley. The anions O-, OH-, C-, CH- and CN- have been detected, as well as unidentified anions with masses 22-65 and 85-110 amu (Chaizy et al. 1991). Organic molecular anions are known to have a significant impact on the charge balance of interstellar clouds and circumstellar envelopes and have been shown to act as catalysts for the gas-phase synthesis of larger hydrocarbon molecules in the ISM, but their importance in cometary comae has not previously been explored. We present details of the first attempt to model the chemistry of anions in cometary comae. Based on the combined chemical and hydrodynamical model of Rodgers & Charnley (2002), we investigate the role of the hydrocarbon and nitrile anions Cn-, CnH- and CnN- in the coma. We calculate the effects of these anions on the charge balance and examine their impact on cometary coma chemistry. References: Chaizy, P. et al. 1991, Nature, 349, 393 Rodgers, S.D. & Charnley, S.B. 2002, MNRAS, 330, 660

  11. Determination of free and total myo-inositol in infant formula and adult/pediatric nutritional formula by high- performance anion exchange chromatography with pulsed amperometric detection, including a novel total extraction using microwave-assisted acid hydrolysis and enzymatic treatment: first action 2012.12.

    Science.gov (United States)

    Ellingson, David; Pritchard, Ted; Foy, Pamela; King, Kathryn; Mitchell, Barbara; Austad, John; Winters, Doug; Sullivan, Darryl; Dowell, Dawn

    2013-01-01

    After an assessment of data generated from a single-laboratory validation study published in J. AOAC Int. 95, 1469-1478 (2012), a method for determining total myo-inositol in infant formula and adult/ pediatric nutritional formula by high-performance anion exchange chromatography with pulsed amperometric detection (HPAEC-PAD), including extraction by using microwave-assisted acid hydrolysis and enzymatic treatment was presented for consideration by AOAC during the AOAC Annual Meeting held in Las Vegas, NV, from September 30 to October 3, 2012. The Expert Review Panel on Infant Formula and Adult Nutritionals concluded that the method met the criteria set by the standard method performance requirements (SMPRs) for the determination of free myo-inositol and approved the method as AOAC Official First Action. The method also determines total myo-inositol, but includes bound sources that the SMPRs exclude. The method involves using HPAEC-PAD for free myo-inositol and a total myo-inositol determination by two different techniques. The first technique uses the conventional acid hydrolysis with 6 h incubation in an autoclave. The second uses a microwave-assisted acid hydrolysis with enzymatic treatment that decreases the extraction time. PMID:24282949

  12. Phosphazene-promoted anionic polymerization

    KAUST Repository

    Zhao, Junpeng

    2014-01-01

    In the recent surge of metal-free polymerization techniques, phosphazene bases have shown their remarkable potential as organic promoters/catalysts for the anionic polymerization of various types of monomers. By complexation with the counterion (e.g. proton or lithium cation), phosphazene base significantly improve the nucleophilicity of the initiator/chain-end resulting in rapid and usually controlled anionic/quasi-anionic polymerization. In this review, we will introduce the general mechanism, i.e. in situ activation (of initiating sites) and polymerization, and summarize the applications of such a mechanism on macromolecular engineering toward functionalized polymers, block copolymers and complex macromolecular architectures.

  13. Uso de Resina de Intercambio Aniónico para la Recuperación del Complejo Oro Tiosulfato desde Soluciones Acuosas Use of Anion Exchange Resin for the Recovery of the Complex Gold Thiosulfate from Aqueous Solutions

    Directory of Open Access Journals (Sweden)

    Miriam E Chaparro

    2012-01-01

    Full Text Available Se estudió la adsorción de oro utilizando la resina AuRIX®100 en medio tiosulfato de amonio, evaluando algunas variables que afectan la cinética del proceso tales como: temperatura, velocidad de agitación, pH, concentración de tiosulfato de amonio (NH42S2O3 y concentración de oro. El estudio se llevó a cabo en un reactor batch y una columna de intercambio iónico. Las condiciones de operación que presentaron mejores resultados de extracción de oro a 25°C, fueron: pH=10.5, velocidad de agitación=500 rpm, [Au]=1 mg/l, [(NH42S2O3]=0.04 M, 5 gramos de resina. Los resultados indican que al aumentar [(NH42S2O3] favorece la adsorción en un 99% durante tres horas, siendo afectado notablemente por la presencia de amonio. Las condiciones con mejores resultados en la columna a 25°C fueron, pH= 10.5 y [Au] =1 mg/l.The adsorption and elution of gold in thiosulfate-ammonia media were studied using the resin AuRIX®100, evaluating some variables that affect the kinetico of the process, such as: temperature, stirring speed, pH, thiosulfate concentration (NH42S2O3 and gold concentration. The study was carried out in a batch reactor and an ion exchange column. The operation conditions that presented better results of gold extraction at 25°C were: pH=10.5, stirring opeed=500 rpm, [Au]=1 mg/l, [(NH42S2O3]=0.04 M, and 5 gramo of resin. The results indicate that by increasing [(NH42S2O3] favors the adsorption by 99% during three hours, being noticeably affected by the presence of ammonia. The conditions with results on the column at 25°C were, pH= 10.5, [Au]=1 mg/l.

  14. Anion release and uptake kinetics: structural changes of layered 2-dimensional ZnNiHN upon uptake of acetate and chlorinated acetate anions.

    Science.gov (United States)

    Machingauta, Cleopas; Hossenlopp, Jeanne M

    2013-12-01

    X-ray diffraction and UV-vis spectroscopy were used for the investigation of ion exchange reaction kinetics of nitrates with acetate (Ac), chloro acetate (ClAc), dichloro acetate (dClAc) and trichloro acetate (tClAc) anions, using zinc nickel hydroxy nitrate (ZnNiHN) as the exchange precursor. The exchange reactions conducted at 24, 30, 40 and 50°C revealed that rate constants were inversely related to the calculated anion electronic spatial extent (ESE), while a direct relationship between rate constants and the average oxygen charges was observed. Temporal solid phase structural transformations were shown to be affected by the nature of the guest anions. The amount of nitrates released into solution has been shown to decrease as the guest anions became more chlorinated. Use of isoconversional approach revealed that activation energies changed significantly with α during dClAc intercalation than for the other anions. The topotactic intercalation of the guest anions, except dClAc, followed the Avrami-Erofe'ev kinetic model for the entire reaction progress. PMID:24054447

  15. Anion Transport with Chalcogen Bonds.

    Science.gov (United States)

    Benz, Sebastian; Macchione, Mariano; Verolet, Quentin; Mareda, Jiri; Sakai, Naomi; Matile, Stefan

    2016-07-27

    In this report, we introduce synthetic anion transporters that operate with chalcogen bonds. Electron-deficient dithieno[3,2-b;2',3'-d]thiophenes (DTTs) are identified as ideal to bind anions in the focal point of the σ holes on the cofacial endocyclic sulfur atoms. Anion binding in solution and anion transport across lipid bilayers are found to increase with the depth of the σ holes of the DTT anionophores. These results introduce DTTs and related architectures as a privileged motif to engineer chalcogen bonds into functional systems, complementary in scope to classics such as 2,2'-bipyrroles or 2,2'-bipyridines that operate with hydrogen bonds and lone pairs, respectively. PMID:27433964

  16. Capacity gradient anion chromatography with a borate complex as eluent.

    Science.gov (United States)

    Yamamoto, A; Inoue, Y; Kodama, S; Matsunaga, A

    1999-07-30

    Complex formation between borate compounds and vicinal diols is well recognized. Generally, in a chemically bonded anion-exchange resin, many hydroxyl groups are introduced on the surface of the resin in order to make the resin hydrophilic. The borate as an eluting reagent also reacts to these hydroxyl groups, and this complex formation decreases the apparent ion-exchange capacity of the column by being dissociated to the anion depending on the eluent pH. In the present work a method is described for the simultaneous determination of anions based on the capacity gradient for suppressed ion chromatography. A Tosoh IC-Anion-PW column and dihydroxyphenylborane-mannitol eluent system were used. To maintain baseline stability, it was helpful to keep the borate concentration constant during a gradient of 16 to 0 mM mannitol as a modifier to prevent the complex formation with the hydroxyl on the resin. The chemical composition of the eluents and gradient profiles are discussed and the application to the analysis of the condensed phosphates with widely varying retention times as food additives in a cheese sample is presented. PMID:10457467

  17. Fósforo disponível determinado por lâmina de resina enterrada Soil phosphorus availability determined by anionic-exchange resin membrane in the soil

    Directory of Open Access Journals (Sweden)

    Jairo André Schlindwein

    2009-02-01

    Full Text Available O uso de lâminas de resina de troca aniônica enterradas no solo permite simular, em parte, o comportamento das raízes das plantas em relação à absorção de P. Essa técnica, utilizada diretamente no solo nas mesmas condições que se cultivam as plantas, sem a necessidade de amostragem do solo, poderia ser uma metodologia promissora de determinação da disponibilidade de P para as culturas. Para testar a validade da técnica, foi realizado um experimento em casa de vegetação, com cinco solos e dois teores de P em que as lâminas de resina foram enterradas no solo na instalação do mesmo (dia zero e retiradas aos 2, 5, 10, 20 e 40 dias depois, para avaliar a extração de P em diferentes solos mantidos com umidade próxima da capacidade de campo, cultivados com milho (método resina-cc, e em solos mantidos saturados com água, sem cultivo e cultivados com arroz (método resina-sat. Também retiraram-se amostras de solo para determinar o P extraído pelos métodos da resina em lâminas padrão, Mehlich-1 e Mehlich-3, para correlacionar com o P extraído pelas culturas. O método Mehlich-1 extraiu, em média, 1,3 e 1,9 vez menos P do que os métodos da resina padrão e Mehlich-3, respectivamente, e o método da resina-cc extraiu em média 2,2 vezes menos P do que o método da resina-sat. Os coeficientes de determinação entre o P extraído pelos métodos e o P absorvido pelo milho e arroz aumentaram, em média, na sequência resina-cc The in situ ion exchange resin membrane allows a partial simulation of the behavior of plant roots regarding phosphorus absorption from soil solution. Soil sampling is rendered unnecessary since the technique is used directly in the soil where the plants are grown and may be a promising methodology in the determination of phosphorus availability for crops. To evaluate the technique, a greenhouse experiment was carried out with resin membranes buried in the soil when plants were sown (day zero and removed

  18. Advanced polymer chemistry of organometallic anions

    Energy Technology Data Exchange (ETDEWEB)

    Chamberlin, R.M.; Abney, K.D. [Los Alamos National Lab., NM (United States); Balaich, G.J.; Fino, S.A. [Air Force Academy, CO (United States)

    1997-11-01

    This is the final report of a one-year, Laboratory Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). The objective of the project was to prepare and characterize new polymers incorporating cobalt dicarbollide. Specific goals were to prepare polymerizable cobalt dicarbollide monomers using the nucleophilic substitution route discovered in laboratories and to establish the reaction conditions required to form polymers from these complexes. This one-year project resulted in two publications (in press), and provided the foundation for further investigations into polymer synthesis and characterization using cobalt dicarbollide and other metallocarboranes. Interest in synthesizing organometallic polymers containing the cobalt bis(dicarbollide) anion is motivated by their possible application as cation exchange materials for the remediation of cesium-137 and strontium-90 from nuclear wastes.

  19. Controlled Release Kinetics in Hydroxy Double Salts: Effect of Host Anion Structure

    Directory of Open Access Journals (Sweden)

    Stephen Majoni

    2014-01-01

    Full Text Available Nanodimensional layered metal hydroxides such as layered double hydroxides (LDHs and hydroxy double salts (HDSs can undergo anion exchange reactions releasing intercalated anions. Because of this, these metal hydroxides have found applications in controlled release delivery of bioactive species such as drugs and pesticides. In this work, isomers of hydroxycinnamate were used as model compounds to systematically explore the effects of anion structure on the rate and extent of anion release in HDSs. Following intercalation and subsequent release of the isomers, it has been demonstrated that the nature and position of substituent groups on intercalated anions have profound effects on the rate and extent of release. The extent of release was correlated with the magnitude of dipole moments while the rate of reaction showed strong dependence on the extent of hydrogen bonding within the layers. The orthoisomer showed a more sustained and complete release as compared to the other isomers.

  20. Determination of polysaccharide content in Haemophilus influenzae type b conjugate vaccines by high performance anion exchange chromatography-pulsed amperometric detector%高效阴离子交换色谱-脉冲安培法测定b型流感嗜血杆菌结合疫苗的多糖含量

    Institute of Scientific and Technical Information of China (English)

    贺鹏飞; 唐静; 李亚南; 李茂光; 叶强

    2013-01-01

    Objective To determine the polyribosylribitol phosphate (PRP) content in Haemophilus influenzae type b conjugate vaccine by high performance anion exchange chromatography-pulsed amperometric detector (HPAEC-PAD).Methods The PRP in test samples of Hib conjugate vaccine or isolated free polysaccharide was hydrolyzed with 0.3 mol/L sodium hydroxide at room temperature in oscillation for (16 ± 8) h,then separated by CarboPac(@) PA-10 anion exchange column,eluted by sodium hydroxide/sodium acetate gradient elution,detected by pulsed amperometric detector,and calculated according to the peak area of test samples.The samples were tested for 2 times,and the relative standard deviation (RSD) of test results was calculated.Meanwhile,the PRP content in test sample or free PRP content of the same batch of vaccine were determined by orcinol method in the appendix of Chinese Pharmacopoeia (Volume Ⅲ,2010 edition),and the result was compared with that by HPAEC-PAD.Results The RSD between 2 test results of the same sample was not more than 4.6%.The total PRP contents in samples S01~S03 determined by HPAEC-PAD were 105%,104% and 106%,while the free PRP contents were 126%,109% and 115% of those by orcinol method,respectively.Conclusion HPAEC-PAD method showed high sensitivity,reproducibility and separation effectiveness for PRP content in Hib conjugate vaccine,by which the samples needed no derivation,and multiple components were determined at the same time,therefore may be used as an alternative method of traditional orcinol method for deter-mination of PRP content in Hib conjugate vaccine.%目的 采用高效阴离子交换色谱-脉冲安培检测法(high performance anion exchange chromatography withpulsed amperometric detector,HPAEC-PAD)测定b型流感嗜血杆菌(haemophilus influenzae type b,Hib)结合疫苗的多聚磷酸核糖基核糖醇(polyribosylribitol phosphate,PRP)多糖含量.方法 用终浓度为0.3N的NaOH溶液将待测疫苗中的PRP多糖