WorldWideScience

Sample records for analog-to-digital converters

  1. Combined analog-to-digital converter

    International Nuclear Information System (INIS)

    Zhukov, A.V.; Rzhendinskaya, S.N.

    1983-01-01

    A 10-bit analog-to-digital converter (ADC) designed for operating in spectrometers with time-dependent filters is described. The ADC operation is based on combining the parallel reading and sequential counting methods. At maximum conversion time of 12 μs, timing series frequency of 25 MHz and foUr reference levels the differential nonlinearity withoUt statistical smoothing (maximum relative channel width deviation from average value) is not more than 4%

  2. Optical analog-to-digital converter

    Science.gov (United States)

    Vawter, G Allen [Corrales, NM; Raring, James [Goleta, CA; Skogen, Erik J [Albuquerque, NM

    2009-07-21

    An optical analog-to-digital converter (ADC) is disclosed which converts an input optical analog signal to an output optical digital signal at a sampling rate defined by a sampling optical signal. Each bit of the digital representation is separately determined using an optical waveguide interferometer and an optical thresholding element. The interferometer uses the optical analog signal and the sampling optical signal to generate a sinusoidally-varying output signal using cross-phase-modulation (XPM) or a photocurrent generated from the optical analog signal. The sinusoidally-varying output signal is then digitized by the thresholding element, which includes a saturable absorber or at least one semiconductor optical amplifier, to form the optical digital signal which can be output either in parallel or serially.

  3. FASTBUS 16-channel 8-bit analog-to-digital converter

    International Nuclear Information System (INIS)

    Parfenov, A.N.; Pilyar, A.V.

    1989-01-01

    The converter module is based on 1107PV3 microcircuits connected in cascade connection. The measured analog signals range is ±2 V. Analog-to-digital conversion is linear. Information from analog-to-digital converter (ADC) is read simultaneously from two channels using FASTBUS channel for ∼40 ns. 16-channel ADC is used in a system to measure characteristics of scintillation hodoscopes module of the SFERA set-up

  4. Time-Interleaved Analog to Digital Converters

    NARCIS (Netherlands)

    Louwsma, S.M.; van Tuijl, Adrianus Johannes Maria; Nauta, Bram

    2010-01-01

    This book describes the research carried out by our PhD student Simon Louwsma at the University of Twente, The Netherlands in the field of high-speed Analogto- Digital (AD) converters. AD converters are crucial circuits for modern systems where information is stored or processed in digital form. Due

  5. Fast parallel-series analog-to-digital converter

    International Nuclear Information System (INIS)

    Pogosov, A.Yu.

    1987-01-01

    Fast analog-to-digital converters are used in systems for detection of rapid processes, nuclear spectroscopy. A 12-digit analog-to-digital converter with conversion time of 160 ns and conversion frequency of 8.3 MHz is described; a segmented digital-to-analog converter with differential non-linearity of < 0.01% and a differential amplifier-limiter with setting time of 80 ns at the error of 0.2% are utilized in the converter; a control device is based on the chain of flip-flop circuit

  6. Three-channel integrating analog-to-digital converter

    Science.gov (United States)

    Stevens, G. L.

    1978-01-01

    A three-channel integrating analog-to-digital converter was added to the complex mixer system to accept the baseband, complex signals generated by the complex mixers and output binary data to the digital demodulator for further processing and recording. The converter was first used for processing multistation data in radar experiments in the spring of 1977.

  7. New technologies for radiation-hardening analog to digital converters

    International Nuclear Information System (INIS)

    Gauthier, M.K.

    1982-12-01

    Surveys of available Analog to Digital Converters (ADC) suitable for precision applications showed that none have the proper combination of accuracy and radiation hardness to meet space and/or strategic weapon requirements. A development program which will result in an ADC device which will serve a number of space and strategic applications. Emphasis was placed on approaches that could be integrated onto a single chip within three to five years

  8. APPLICATION BASED COMPARISON OF DIFFERENT ANALOG TO DIGITAL CONVERTER ARCHITECTURES

    OpenAIRE

    VEEPSA BHATIA,; NEETA PANDEY; ASOK BHATTACHARYYA

    2010-01-01

    A review study of the most popular type of Analog to Digital Converters- successive approximations, flash, pipelined and sigma-delta has been performed in this paper. The paper elaborates the fundamental operating principles of these architectures and the sources of error experienced in each of these architectures. Further, design considerations and implications, for each architecture, have been put forth. An application based comparison has also been drawn for these architectures with the he...

  9. Reference-Free CMOS Pipeline Analog-to-Digital Converters

    CERN Document Server

    Figueiredo, Michael; Evans, Guiomar

    2013-01-01

    This book shows that digitally assisted analog-to-digital converters are not the only way to cope with poor analog performance caused by technology scaling. It describes various analog design techniques that enhance the area and power efficiency without employing any type of digital calibration circuitry. These techniques consist of self-biasing for PVT enhancement, inverter-based design for improved speed/power ratio, gain-of-two obtained by voltage sum instead of charge redistribution, and current-mode reference shifting instead of voltage reference shifting. Together, these techniques allow enhancing the area and power efficiency of the main building blocks of a multiplying digital-to-analog converter (MDAC) based stage, namely, the flash quantizer, the amplifier, and the switched capacitor network of the MDAC. Complementing the theoretical analyses of the various techniques, a power efficient operational transconductance amplifier is implemented and experimentally characterized. Furthermore, a medium-low ...

  10. Photonic analog-to-digital converter via asynchronous oversampling

    Science.gov (United States)

    Carver, Spencer; Reeves, Erin; Siahmakoun, Azad; Granieri, Sergio

    2012-06-01

    This paper presents a hybrid opto-electronic asynchronous delta-sigma modulator, implemented in the form of a fiber-optic Analog-to-Digital converter (ADC). This architecture was chosen for its independence of an external clock and ease of demodulation through a single low-pass filter stage. The fiber-optic prototype consists of an input laser (wavelength λ1) which is modulated with an input RF signal, a high-speed comparator circuit working as bi-stable quantizer, and a fiber-optic loop that includes a SOA and a band-pass filter that act as a leaky integrator. The fiber-optic loop acts as a fiber-ring resonator (FRR), and defines the resonance wavelength λ2 of the system. The gain within this loop is modified through cross-gain modulation (XGM) by the input wavelength λ1, and thus achieves the desired modulation effect. The proposed architecture has been constructed and characterized at a sampling rate of 15.4 MS/s processing input analog signals in the range of dc-3 MHz with a signal-to-noise ratio of 36 dB and an effective number of bits of 5.7.

  11. Circuit with a successive approximation analog to digital converter

    NARCIS (Netherlands)

    Louwsma, S.M.; Vertregt, Maarten

    2011-01-01

    During successive approximation analog to digital conversion a series of successive digital reference values is selected that converges towards a digital representation of an analog input signal. An analog reference signal is generated dependent on the successive digital reference values and

  12. Circuit with a successive approximation analog to digital converter

    NARCIS (Netherlands)

    Louwsma, S.M.; Vertregt, Maarten

    2010-01-01

    During successive approximation analog to digital conversion a series of successive digital reference values is selected that converges towards a digital representation of an analog input signal. An analog reference signal is generated dependent on the successive digital reference values and

  13. Very High-Performance Advanced Filter Bank Analog-to-Digital Converter (AFB ADC) Project

    National Research Council Canada - National Science Library

    Velazquez, Scott

    1999-01-01

    ... of the art by using a parallel array of individual commercial off the shelf converters. The significant performance improvements afforded by the Advanced Filter Bank Analog to Digital Converter (AFB ADC...

  14. Charge integration successive approximation analog-to-digital converter for focal plane applications using a single amplifier

    Science.gov (United States)

    Zhou, Zhimin (Inventor); Pain, Bedabrata (Inventor)

    1999-01-01

    An analog-to-digital converter for on-chip focal-plane image sensor applications. The analog-to-digital converter utilizes a single charge integrating amplifier in a charge balancing architecture to implement successive approximation analog-to-digital conversion. This design requires minimal chip area and has high speed and low power dissipation for operation in the 2-10 bit range. The invention is particularly well suited to CMOS on-chip applications requiring many analog-to-digital converters, such as column-parallel focal-plane architectures.

  15. Radiation-hard analog-to-digital converters for space and strategic applications

    Science.gov (United States)

    Gauthier, M. K.; Dantas, A. R. V.

    1985-01-01

    During the course of the Jet Propulsion Laboratory's program to study radiation-hardened analog-to-digital converters (ADCs), numerous milestones have been reached in manufacturers' awareness and technology development and transfer, as well as in user awareness of these developments. The testing of ADCs has also continued with twenty different ADCs from seven manufacturers, all tested for total radiation dose and three tested for neutron effects. Results from these tests are reported.

  16. Effects of Analog-to-Digital Converter Nonlinearities on Radar Range-Doppler Maps

    Energy Technology Data Exchange (ETDEWEB)

    Doerry, Armin Walter [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Dubbert, Dale F. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Tise, Bertice L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-07-01

    Radar operation, particularly Ground Moving Target Indicator (GMTI) radar modes, are very sensitive to anomalous effects of system nonlinearities. These throw off harmonic spurs that are sometimes detected as false alarms. One significant source of nonlinear behavior is the Analog to Digital Converter (ADC). One measure of its undesired nonlinearity is its Integral Nonlinearity (INL) specification. We examine in this report the relationship of INL to GMTI performance.

  17. Data input from an analog-to-digital converter into the M-6000 computer

    International Nuclear Information System (INIS)

    Kalashnikov, A.M.; Sheremet'ev, A.K.

    1978-01-01

    A device for spectrometric data input from the ADC-4096 into the M-6000 computer memory operating in the information storage regime is described. The input device made on integrated circuits coordinates signal levels of the fast response analog-to-digital converter and computer with the help of resistors and inverters. Besides, the input forms a strobe to trigger an increment channel used to record information into the computer memory. The use of the input device permits to get rid of the intermediate information storage in the analyzer memory and ensures fast response of the devices

  18. Compendium of Single-Event Latchup and Total Ionizing Dose Test Results of Commercial Analog to Digital Converters

    Science.gov (United States)

    Irom, Farokh; Agarwal, Shri G.

    2012-01-01

    This paper reports single-event latchup and total dose results for a variety of analog to digital converters targeted for possible use in NASA spacecraft's. The compendium covers devices tested over the last 15 years.

  19. Multi-gigahertz performance of a superconducting analog-to-digital converter

    Energy Technology Data Exchange (ETDEWEB)

    Luong, H.C.; Van Duzer, T. [Univ. of California, Berkeley, CA (United States)

    1994-12-31

    This paper presents the progress the authors have made on their design, fabrication, and testing of a fully parallel superconducting analog-to-digital converter (ADC) with multi-gigahertz clock frequencies and input bandwidth. To their best knowledge, this converter is the first flash-type analog-to-digital converter ever reported in Josephson technology that fully integrates a quantizer and a thermometer-to-binary encoder to achieve binary outputs. In this design, the quantizer consists of 2{sup N}-1 comparators, each of which is realized using a hysteretic one-junction sampling SQUID driving a two-junction readout SQUID. A new logic family has been designed based on the same comparator building block and has been used to implement the thermometer-to-binary encoder. Taking advantage of the fact that the encoder`s input is thermometer-coded, They have designed three-input and four-input quasi-XOR gates with only three NAND gates and therefore reduced significantly the total gate count. Functionalities of all the sub-circuits have been verified experimentally at clock frequencies up to 3 GHz, which is limited by their currently available testing equipment.

  20. Minus 55 to plus 200 deg C 12 bit analog-to-digital converter

    Science.gov (United States)

    Smith, L. R.; Prazak, P. R.

    1981-01-01

    A 12 bit successive approximation analog to digital converter that offers moderately high speed precision data conversion at a reasonable level of cost and complexity is studied. The ADCH10HT extends this capability over a temperature range of -55 to +200 C. No missing-code performance is maintained over the entire temperature range. The converter is completely self-contained with internal clock and +10 volt reference. The CMOS devices offer low power dissipation, so that the internal temperature of the hybrid circuit does not rise as much from self heating. In CMOS circuits, pn junction leakage currents are returned to the supplies so that the logic keeps working at temperatures up to 250 C.

  1. SEM analysis of ionizing radiation effects in an analog to digital converter /AD571/

    Science.gov (United States)

    Gauthier, M. K.; Perret, J.; Evans, K. C.

    1981-01-01

    The considered investigation is concerned with the study of the total-dose degradation mechanisms in an IIL analog to digital (A/D) converter. The A/D converter is a 10 digit device having nine separate functional units on the chip which encompass several hundred transistors and circuit elements. It was the objective of the described research to find the radiation sensitive elements by a systematic search of the devices on the LSI chip. The employed technique using a scanning electron microscope to determine the functional blocks of an integrated circuit which are sensitive to ionizing radiation and then progressively zeroing in on the soft components within those blocks, proved extremely successful on the AD571. Four functional blocks were found to be sensitive to radiation, including the Voltage Reference, DAC, IIL Clock, and IIL SAR.

  2. A behavioral simulator for switched-capacitor sigma-delta modulator analog-to-digital converter

    International Nuclear Information System (INIS)

    San, H. Y.; Rezaul Hasan, S. M.

    1998-01-01

    In this paper, a PC-based simulator for state of the art oversampled switched-capacitor sigma-delta analog-to-digital converters is presented. The proposed simulator employs behavioral model of switched-capacitor integrator and non-linear quantizer to stimulate the system. The behavioral simulation of the integrator is also verified with SPICE. The simulator is fully integrated and standalone. It integrates an input netlist file interpreter, a behavioral simulator, a generic part library and a powerful post-processor to evaluate the SNR, SDR And TSNR. Both passive and active sensitivities can be investigated by the proposed simulator. The simulator is coded in C++, and is very fast

  3. Multi-channel analog-to-digital converter in the VECTOR-CAMAC systems

    International Nuclear Information System (INIS)

    Borodyanskij, M.E.; Moravskij, E.I.

    1986-01-01

    A four-channel analog-to-digital converter (ADC) realized on microcircuits of high level of integration is described. Refinement of the result of conversion from one tact to another is ensured at the expense of introducing redemdancy of signal conversion at intermediate tacts. The ADC represents a unit of the Vector system: a controller is placed in the second unit. The ADS is compatibl with the Vector system and after negligible alternations it can be performed in the CAMAC system. Time of ADSsub(n) conversion in one channel is 5μs, output code is 14-digit, binary maximum value of integral nonlinearity <= 0.05% from the dynamic range of measured signals is +- 10V, capacity of the immediate memonry is 1024 14-digit words

  4. Proposition of a scheme for adaptive/intelligent analog-to-digital converters

    International Nuclear Information System (INIS)

    Vaidya, P.P.; Kataria, S.K.

    2001-01-01

    The paper proposes design of a new class of Analog to Digital Converters (ADC's) which we call as Intelligent ADC's with moving resolution. Unlike presently available ADC's which are designed for specific range of applications and give fixed resolution and conversion time, the intelligent ADC's described here can adjust their resolution during the process of conversion, depending upon nature of input signal to make optimum use of the hard-ware. It is possible to use an intelligent ADC to give resolution ranging from 8 bit to 16 bit and conversion time ranging from few nano sec. to few micro secs. These ADC's have significant advantages over conventional ones when used for nuclear pulse spectroscopy as well as for process control applications. (author)

  5. High-speed and high-resolution analog-to-digital and digital-to-analog converters

    NARCIS (Netherlands)

    van de Plassche, R.J.

    1989-01-01

    Analog-to-digital and digital-to-analog converters are important building blocks connecting the analog world of transducers with the digital world of computing, signal processing and data acquisition systems. In chapter two the converter as part of a system is described. Requirements of analog

  6. Designed cell consortia as fragrance-programmable analog-to-digital converters.

    Science.gov (United States)

    Müller, Marius; Ausländer, Simon; Spinnler, Andrea; Ausländer, David; Sikorski, Julian; Folcher, Marc; Fussenegger, Martin

    2017-03-01

    Synthetic biology advances the rational engineering of mammalian cells to achieve cell-based therapy goals. Synthetic gene networks have nearly reached the complexity of digital electronic circuits and enable single cells to perform programmable arithmetic calculations or to provide dynamic remote control of transgenes through electromagnetic waves. We designed a synthetic multilayered gaseous-fragrance-programmable analog-to-digital converter (ADC) allowing for remote control of digital gene expression with 2-bit AND-, OR- and NOR-gate logic in synchronized cell consortia. The ADC consists of multiple sampling-and-quantization modules sensing analog gaseous fragrance inputs; a gas-to-liquid transducer converting fragrance intensity into diffusible cell-to-cell signaling compounds; a digitization unit with a genetic amplifier circuit to improve the signal-to-noise ratio; and recombinase-based digital expression switches enabling 2-bit processing of logic gates. Synthetic ADCs that can remotely control cellular activities with digital precision may enable the development of novel biosensors and may provide bioelectronic interfaces synchronizing analog metabolic pathways with digital electronics.

  7. A device for the correction of differential non linearity in an analog to digital converter of sucessive approximation type

    International Nuclear Information System (INIS)

    Monteiro, P.R.B.

    1983-01-01

    It is shown that an analog to digital converter of sucessive approximation type may be used in the nuclear spectroscopy work provided its differential non linearity is suitably corrected. The function of an analog to digital converter in a nuclear data acquisition system is described. The main parameters which characterize this function have also been defined. A comparative study of the two types of A/D converters, Wilkinson type and the sucessive approximation type, has been carried out. Its is concluded that the later type of the converter is more convenient when it has been corrected for its differential non linearity. THe source of error of the differential non linearity is both qualitatively and quantitatively analysed and the design and construction of a corrector circuit is described which uses the sliding scale method. The experimental results show that the differential non linearity error is reduced to less than 1%. (Author) [pt

  8. Proton-induced single event upset characterisation of a 1 giga-sample per second analog to digital converter

    International Nuclear Information System (INIS)

    Reed, R.A.; Marshall, P.W.; Carts, M.A.

    1999-01-01

    The SPT7760 is an analog to digital converter that is used in satellite for digital processing. In this paper we describe the characterization and analysis of proton-induced single event upsets (SEU) for the SPT7760 operating at sample rates from 125 Msps (Mega-samples per second) to 1 Gsps. The SEU cross-section has been measured as a function of sample rate for various input levels. The data collected is clearly non-linear for all cases. The data shows that this device has a relative low cross-section for proton-induced SEUs and remains functional at a proton dose of 580 krad (Si). (A.C.)

  9. From analog to digital

    CERN Document Server

    Belleman, J

    2008-01-01

    Analog-to-digital conversion and its reverse, digital-to-analog conversion, are ubiquitous in all modern electronics, from instrumentation and telecommunication equipment to computers and entertainment. We shall explore the consequences of converting signals between the analog and digital domains and give an overview of the internal architecture and operation of a number of converter types. The importance of analog input and clock signal integrity will be explained and methods to prevent or mitigate the effects of interference will be shown. Examples will be drawn from several manufacturers' datasheets.

  10. A Design of a New Column-Parallel Analog-to-Digital Converter Flash for Monolithic Active Pixel Sensor.

    Science.gov (United States)

    Chakir, Mostafa; Akhamal, Hicham; Qjidaa, Hassan

    2017-01-01

    The CMOS Monolithic Active Pixel Sensor (MAPS) for the International Linear Collider (ILC) vertex detector (VXD) expresses stringent requirements on their analog readout electronics, specifically on the analog-to-digital converter (ADC). This paper concerns designing and optimizing a new architecture of a low power, high speed, and small-area 4-bit column-parallel ADC Flash. Later in this study, we propose to interpose an S/H block in the converter. This integration of S/H block increases the sensitiveness of the converter to the very small amplitude of the input signal from the sensor and provides a sufficient time to the converter to be able to code the input signal. This ADC is developed in 0.18  μ m CMOS process with a pixel pitch of 35  μ m. The proposed ADC responds to the constraints of power dissipation, size, and speed for the MAPS composed of a matrix of 64 rows and 48 columns where each column ADC covers a small area of 35 × 336.76  μ m 2 . The proposed ADC consumes low power at a 1.8 V supply and 100 MS/s sampling rate with dynamic range of 125 mV. Its DNL and INL are 0.0812/-0.0787 LSB and 0.0811/-0.0787 LSB, respectively. Furthermore, this ADC achieves a high speed more than 5 GHz.

  11. A Design of a New Column-Parallel Analog-to-Digital Converter Flash for Monolithic Active Pixel Sensor

    Directory of Open Access Journals (Sweden)

    Mostafa Chakir

    2017-01-01

    Full Text Available The CMOS Monolithic Active Pixel Sensor (MAPS for the International Linear Collider (ILC vertex detector (VXD expresses stringent requirements on their analog readout electronics, specifically on the analog-to-digital converter (ADC. This paper concerns designing and optimizing a new architecture of a low power, high speed, and small-area 4-bit column-parallel ADC Flash. Later in this study, we propose to interpose an S/H block in the converter. This integration of S/H block increases the sensitiveness of the converter to the very small amplitude of the input signal from the sensor and provides a sufficient time to the converter to be able to code the input signal. This ADC is developed in 0.18 μm CMOS process with a pixel pitch of 35 μm. The proposed ADC responds to the constraints of power dissipation, size, and speed for the MAPS composed of a matrix of 64 rows and 48 columns where each column ADC covers a small area of 35 × 336.76 μm2. The proposed ADC consumes low power at a 1.8 V supply and 100 MS/s sampling rate with dynamic range of 125 mV. Its DNL and INL are 0.0812/−0.0787 LSB and 0.0811/−0.0787 LSB, respectively. Furthermore, this ADC achieves a high speed more than 5 GHz.

  12. Compensation of multi-channel mismatches in high-speed high-resolution photonic analog-to-digital converter.

    Science.gov (United States)

    Yang, Guang; Zou, Weiwen; Yu, Lei; Wu, Kan; Chen, Jianping

    2016-10-17

    We demonstrate a method to compensate multi-channel mismatches that intrinsically exist in a photonic analog-to-digital converter (ADC) system. This system, nominated time-wavelength interleaved photonic ADC (TWI-PADC), is time-interleaved via wavelength demultiplexing/multiplexing before photonic sampling, wavelength demultiplexing channelization, and electronic quantization. Mismatches among multiple channels are estimated in frequency domain and hardware adjustment are used to approach the device-limited accuracy. A multi-channel mismatch compensation algorithm, inspired from the time-interleaved electronic ADC, is developed to effectively improve the performance of TWI-PADC. In the experiment, we configure out a 4-channel TWI-PADC system with 40 GS/s sampling rate based on a 10-GHz actively mode-locked fiber laser. After multi-channel mismatch compensation, the effective number of bit (ENOB) of the 40-GS/s TWI-PADC system is enhanced from ~6 bits to >8.5 bits when the RF frequency is within 0.1-3.1 GHz and from ~6 bits to >7.5 bits within 3.1-12.1 GHz. The enhanced performance of the TWI-PADC system approaches the limitation determined by the timing jitter and noise.

  13. Analog-to-digital conversion

    CERN Document Server

    Pelgrom, Marcel J M

    2010-01-01

    The design of an analog-to-digital converter or digital-to-analog converter is one of the most fascinating tasks in micro-electronics. In a converter the analog world with all its intricacies meets the realm of the formal digital abstraction. Both disciplines must be understood for an optimum conversion solution. In a converter also system challenges meet technology opportunities. Modern systems rely on analog-to-digital converters as an essential part of the complex chain to access the physical world. And processors need the ultimate performance of digital-to-analog converters to present the results of their complex algorithms. The same progress in CMOS technology that enables these VLSI digital systems creates new challenges for analog-to-digital converters: lower signal swings, less power and variability issues. Last but not least, the analog-to-digital converter must follow the cost reduction trend. These changing boundary conditions require micro-electronics engineers to consider their design choices for...

  14. Mixed Linear/Square-Root Encoded Single Slope Ramp Provides a Fast, Low Noise Analog to Digital Converter with Very High Linearity for Focal Plane Arrays

    Science.gov (United States)

    Wrigley, Christopher James (Inventor); Hancock, Bruce R. (Inventor); Newton, Kenneth W. (Inventor); Cunningham, Thomas J. (Inventor)

    2014-01-01

    An analog-to-digital converter (ADC) converts pixel voltages from a CMOS image into a digital output. A voltage ramp generator generates a voltage ramp that has a linear first portion and a non-linear second portion. A digital output generator generates a digital output based on the voltage ramp, the pixel voltages, and comparator output from an array of comparators that compare the voltage ramp to the pixel voltages. A return lookup table linearizes the digital output values.

  15. A Calibration Method for Nonlinear Mismatches in M-Channel Time-Interleaved Analog-to-Digital Converters Based on Hadamard Sequences

    Directory of Open Access Journals (Sweden)

    Husheng Liu

    2016-11-01

    Full Text Available The time-interleaved analog-to-digital converter (TIADC is an architecture used to achieve a high sampling rate and high dynamic performance. However, estimation and compensation methods are required to maintain the dynamic performance of the constituent analog-to-digital converters (ADCs due to channel mismatches. This paper proposes a blind adaptive method to calibrate the nonlinear mismatches in M-channel TIADCs (M-TIADCs. The nonlinearity-induced error signal is reconstructed by the proposed multiplier Hadamard transform (MHT structure, and the nonlinear parameters are estimated by the filtered-X least-mean square (FxLMS algorithm. The performance of cascade calibration is also analyzed. The numerical simulation results show that the proposed method consumes much less hardware resources while maintaining the calibration performance.

  16. Simulation of continuously logical base cells (CL BC) with advanced functions for analog-to-digital converters and image processors

    Science.gov (United States)

    Krasilenko, Vladimir G.; Lazarev, Alexander A.; Nikitovich, Diana V.

    2017-10-01

    The paper considers results of design and modeling of continuously logical base cells (CL BC) based on current mirrors (CM) with functions of preliminary analogue and subsequent analogue-digital processing for creating sensor multichannel analog-to-digital converters (SMC ADCs) and image processors (IP). For such with vector or matrix parallel inputs-outputs IP and SMC ADCs it is needed active basic photosensitive cells with an extended electronic circuit, which are considered in paper. Such basic cells and ADCs based on them have a number of advantages: high speed and reliability, simplicity, small power consumption, high integration level for linear and matrix structures. We show design of the CL BC and ADC of photocurrents and their various possible implementations and its simulations. We consider CL BC for methods of selection and rank preprocessing and linear array of ADCs with conversion to binary codes and Gray codes. In contrast to our previous works here we will dwell more on analogue preprocessing schemes for signals of neighboring cells. Let us show how the introduction of simple nodes based on current mirrors extends the range of functions performed by the image processor. Each channel of the structure consists of several digital-analog cells (DC) on 15-35 CMOS. The amount of DC does not exceed the number of digits of the formed code, and for an iteration type, only one cell of DC, complemented by the device of selection and holding (SHD), is required. One channel of ADC with iteration is based on one DC-(G) and SHD, and it has only 35 CMOS transistors. In such ADCs easily parallel code can be realized and also serial-parallel output code. The circuits and simulation results of their design with OrCAD are shown. The supply voltage of the DC is 1.8÷3.3V, the range of an input photocurrent is 0.1÷24μA, the transformation time is 20÷30nS at 6-8 bit binary or Gray codes. The general power consumption of the ADC with iteration is only 50÷100μW, if the

  17. Analog-to-digital conversion

    CERN Document Server

    Pelgrom, Marcel

    2017-01-01

    This textbook is appropriate for use in graduate-level curricula in analog-to-digital conversion, as well as for practicing engineers in need of a state-of-the-art reference on data converters. It discusses various analog-to-digital conversion principles, including sampling, quantization, reference generation, nyquist architectures and sigma-delta modulation. This book presents an overview of the state of the art in this field and focuses on issues of optimizing accuracy and speed, while reducing the power level. This new, third edition emphasizes novel calibration concepts, the specific requirements of new systems, the consequences of 22-nm technology and the need for a more statistical approach to accuracy. Pedagogical enhancements to this edition include additional, new exercises, solved examples to introduce all key, new concepts and warnings, remarks and hints, from a practitioner’s perspective, wherever appropriate. Considerable background information and practical tips, from designing a PCB, to lay-o...

  18. A CAMAC unit for charge measuring and pulse shape recording based on a fast, 8-bit parallel analog-to-digital converter

    International Nuclear Information System (INIS)

    Kulka, Z.; Kreciejewski, M.; Nadachowski, M.

    1990-08-01

    A device designed mainly for measuring systems for testing parameters of some type of detectors used in the high energy physics is described. The device is one-module CAMAC unit. It is equipped in a fast, 8-bit parallel analog-to-digital converter ''flash''type with a gated integrator at the input and a static RAM (4096 x 8 bit) at the output. The device enables measurements of the charge in pulses from detectors or registration of the shape of these pulses. The construction, operation and parameters of the circuits of the device are described and the way of programming functions using CAMAC dataway is given. 8 refs., 9 figs. (author)

  19. Estimation of channel mismatches in time-interleaved analog-to-digital converters based on fractional delay and sine curve fitting.

    Science.gov (United States)

    Guo, Lianping; Tian, Shulin; Jiang, Jun

    2015-03-01

    This paper proposes an algorithm to estimate the channel mismatches in time-interleaved analog-to-digital converter (TIADC) based on fractional delay (FD) and sine curve fitting. Choose one channel as the reference channel and apply FD to the output samples of reference channel to obtain the ideal samples of non-reference channels with no mismatches. Based on least square method, the sine curves are adopted to fit the ideal and the actual samples of non-reference channels, and then the mismatch parameters can be estimated by comparing the ideal sine curves and the actual ones. The principle of this algorithm is simple and easily understood. Moreover, its implementation needs no extra circuits, lowering the hardware cost. Simulation results show that the estimation accuracy of this algorithm can be controlled within 2%. Finally, the practicability of this algorithm is verified by the measurement results of channel mismatch errors of a two-channel TIADC prototype.

  20. Analog-to-digital conversion

    CERN Document Server

    Pelgrom, Marcel J. M

    2013-01-01

    This textbook is appropriate for use in graduate-level curricula in analog to digital conversion, as well as for practicing engineers in need of a state-of-the-art reference on data converters.  It discusses various analog-to-digital conversion principles, including sampling, quantization, reference generation, nyquist architectures and sigma-delta modulation.  This book presents an overview of the state-of-the-art in this field and focuses on issues of optimizing accuracy and speed, while reducing the power level. This new, second edition emphasizes novel calibration concepts, the specific requirements of new systems, the consequences of 45-nm technology and the need for a more statistical approach to accuracy.  Pedagogical enhancements to this edition include more than twice the exercises available in the first edition, solved examples to introduce all key, new concepts and warnings, remarks and hints, from a practitioner’s perspective, wherever appropriate.  Considerable background information and pr...

  1. Design of a low-power flash analog-to-digital converter chip for temperature sensors in 0.18 µm CMOS process

    Directory of Open Access Journals (Sweden)

    Al Al

    2015-01-01

    Full Text Available Current paper proposes a simple design of a 6-bit flash analog-to-digital converter (ADC by process in 0.18 μm CMOS. ADC is expected to be used within a temperature sensor which provides analog data output having a range of 360 mV to 560 mV. The complete system consisting of three main blocks, which are the threshold inverter quantization (TIQ-comparator, the encoder and the parallel input serial output (PISO register. The TIQ-comparator functions as quantization of the analog data to the thermometer code. The encoder converts this thermometer code to 6-bit binary code and the PISO register transforms the parallel data into a data series. The design aims to get a flash ADC on low power dissipation, small size and compatible with the temperature sensors. The method is proposed to set each of the transistor channel length to find out the threshold voltage difference of the inverter on the TIQ comparator. A portion design encoder and PISO registers circuit selected a simple circuit with the best performance from previous studies and adjusted to this system. The design has an input range of 285 to 600 mV and 6-bit resolution output. The chip area of the designed ADC is 844.48 x 764.77 µm2 and the power dissipation is 0.162 µW with 1.6 V supply voltage.

  2. Design and implementation of a platform for experimental testing and validation of analog-to-digital converters: static and dynamic parameters

    Directory of Open Access Journals (Sweden)

    Mansour Imen Ben

    2017-01-01

    Full Text Available This paper presents an implementation of a data acquisition system for analog-to-digital converters (ADCs using “Laboratory Virtual Instrument Engineering Workbench (LabVIEW” as software for data analysis. The designed and implemented platform allows interaction with the device under test through means of data acquisition and instrument controls. Developing custom tests in LabVIEW can result in reduced test time, which in turn will help reduce costs in testing. This system was developed for evaluation purposes of ADC's static and dynamic parameters (gain error, offset error, DNL, INL, SNR, SINAD, IMD, etc. using single and multi-frequency signals. The virtual control and analysis instrument was created in “LabVIEW” environment to control test signals generation and data acquisition. The testing performance of the platform is demonstrated using the classical ADC circuit “ADC0804”. A comparison with experimental results obtained by CANTEST platform from Bordeaux University (France is also presented to highlight our platform.

  3. A 515 nW, 0-18 dB Programmable Gain Analog-to-Digital Converter for In-Channel Neural Recording Interfaces.

    Science.gov (United States)

    Rodriguez-Perez, Alberto; Delgado-Restituto, Manuel; Medeiro, Fernando

    2014-06-01

    This paper presents a low-area low-power Switched-Capacitor (SC)-based Programmable-Gain Analog-to-Digital Converter (PG-ADC) suitable for in-channel neural recording applications. The PG-ADC uses a novel implementation of the binary search algorithm that is complemented with adaptive biasing techniques for power saving. It has been fabricated in a standard CMOS 130 nm technology and only occupies 0.0326 mm(2). The PG-ADC has been optimized to operate under two different sampling modes, 27 kS/s and 90 kS/s. The former is tailored for raw data conversion of neural activity, whereas the latter is used for the on-the-fly feature extraction of neural spikes. Experimental results show that, under a voltage supply of 1.2 V, the PG-ADC obtains an ENOB of 7.56 bit (8-bit output) for both sampling modes, regardless of the gain setting. The amplification gain can be programmed from 0 to 18 dB. The power consumption of the PG-ADC at 90 kS/s is 1.52 μW with a FoM of 89.49 fJ/conv, whereas at 27 kS/s it consumes 515 nW and obtains a FoM of 98.31 fJ/conv .

  4. FPGA implementation of a single-input fuzzy logic controller for boost converter with the absence of an external analog-to-digital converter

    DEFF Research Database (Denmark)

    Taeed, Fazel; Salam, Z.; Ayob, S.

    2012-01-01

    In this paper, the single-input fuzzy logic controller (FLC) (SIFLC) for boost converter output-voltage regulation is proposed. The SIFLC utilizes the signed distance method that reduces the multidimensional rule table to 1-D with only one input variable, i.e., distance d. The simplification allows...... for the control surface to be approximated by a piecewise linear. It is shown that, despite the simplicity of SIFLC, its control performance is almost equivalent to that of the conventional FLC. As a proof of concept, the SIFLC is implemented using the Altera EP2C35F672C6N field-programmable gate array (FPGA......) and applied on a 50-W boost converter. The SIFLC is compared to the proportional-integral controller; the simulation and practical results indicate that SIFLC exhibits excellent performance for step load and input reference changes. Another feature of this work is the absence of an external analog...

  5. Analog to digital conversion for nuclear spectrometry

    International Nuclear Information System (INIS)

    Carvalho, P.V.R. de.

    1982-04-01

    A study of the analog to digital conversion techniques for nuclear spectrometry is presented and the main design philosophies of nuclear ADC's are compared. Among them, the most suitable for the current Brazilian conditions, concerning the specifications and components avaiability is the one that employs a statistical correction of successive approximation converters. This technique is described in full detail. A prototype has been developed an tested for the practical demonstration of the theoretical conclusions. These tests was carried on nuclear spectrometry data aquisition system whose implementation is also described. (Author) [pt

  6. 23 µW 8.9-effective number of bit 1.1 MS/s successive approximation register analog-to-digital converter with an energy-efficient digital-to-analog converter switching scheme

    Directory of Open Access Journals (Sweden)

    Lei Sun

    2014-08-01

    Full Text Available This study presents a successive approximation register analog-to-digital converter with an energy-efficient switching scheme. A split-most significant bit capacitor array is used with a least significant bit-down switching scheme. Compared with the conventional binary-weighted capacitor array, it reduces the area and average switching energy by 50 and 87% under the same unit capacitor. Moreover, capacitor matching requirement is relaxed by 75%. A prototype design was fabricated in a 0.13 µm complementary metal oxide semiconductor process. It consumes 23.2 µW under 1 V analog supply and 0.5 V digital supply. Measured results show a peak signal-to-distortion-and-noise ratio of 55.2 dB and an effective resolution bandwidth up to 1.1 MHz when it operates at 1.1 MS/s. Its figure-of-merit is 44.1 fJ/conversion-step.

  7. Ultra-High Speed Analog-to-Digital Converters in 14nm FinFET Process and Usage in Digital and Hybrid Phased Array Systems

    Science.gov (United States)

    2017-03-01

    insight into future trends. Background Phased array systems have been in existence for decades for use in radar, sonar , communications, and...factor of 2 raised to the measured ENOB as shown below; Where, The units for the Walden FoM are in Joules per conversion- step. As recently as...2008, typical values for the Walden FoM were approximately 1 to 3 pico-joules per conversion- step for converters operating at sample rates as high as 1

  8. Optical domain analog to digital conversion methods and apparatus

    Science.gov (United States)

    Vawter, Gregory A

    2014-05-13

    Methods and apparatus for optical analog to digital conversion are disclosed. An optical signal is converted by mapping the optical analog signal onto a wavelength modulated optical beam, passing the mapped beam through interferometers to generate analog bit representation signals, and converting the analog bit representation signals into an optical digital signal. A photodiode receives an optical analog signal, a wavelength modulated laser coupled to the photodiode maps the optical analog signal to a wavelength modulated optical beam, interferometers produce an analog bit representation signal from the mapped wavelength modulated optical beam, and sample and threshold circuits corresponding to the interferometers produce a digital bit signal from the analog bit representation signal.

  9. Method and apparatus for low power analog-to-digital conversion

    Science.gov (United States)

    De Geronimo, Gianluigi; Nambiar, Neena

    2013-10-01

    A method and apparatus for analog-to-digital conversion. An Analog-to-Digital Converter (ADC) includes M ADC.sub.j, j=1, 2, . . . , M. Each ADC.sub.j comprises a number of cells each of which comprises a first switch, a second switch, a current sink and an inverter. An inverter of a cell in an ADC.sub.j changes state in response to a current associate with an input signal of the ADC.sub.j exceeding a threshold, thus switching on the next cell. Each ADC.sub.j is enabled to perform analog-to-digital conversion on a residual current of a previous ADC.sub.j-1 after the previous ADC.sub.j-1 has completed its analog-to-digital conversion and has been disabled.

  10. Low-Power, Low-Voltage Analog to Digital ΣΔ

    DEFF Research Database (Denmark)

    Wismar, Ulrik Sørensen

    2007-01-01

    implementations of audio band modulators used as CMOS analog to digital converters. The intended application is hearing aids where analog to digital converters are used to convert the preamplied signal from a microphone into a digital signal which is fed into a microprocessor. A hearing aid is battery driven......, and since long operation time is required, low supply voltage and low power consumption are of paramount importance. Consequently, various topologies have been compared to nd the most power ecient audio frequency modulator topology. Chapter 4 of this thesis compares power consumption of two of the most...... prevalent topologies, the single-loop modulator with integration in discrete time and the single-loop modulator with integration in continuous time. Both modulator topologies are with feedback, and all intermediate signals are in the voltage mode. Chapter 5 treats a modulator without feedback. Another...

  11. Doubling-resolution analog-to-digital conversion based on PIC18F45K80

    Directory of Open Access Journals (Sweden)

    Yueyang Yuan

    2014-08-01

    Full Text Available Aiming at the analog signal being converted into the digital with a higher precision, a method to improve the analog-to-digital converter (ADC resolution is proposed and described. Based on the microcomputer PIC18F45K80 in which the internal ADC modules are embedded, a circuit is designed for doubling the resolution of ADC. According to the circuit diagram, the mathematical formula for calculating this resolution is derived. The corresponding software and print circuit board assembly is also prepared. With the experiment, a 13 bit ADC is achieved based on the 12 bit ADC module predesigned in the PIC18F45K80.

  12. Analog-to-digital conversion using custom CMOS analog memory for the EOS time projection chamber

    International Nuclear Information System (INIS)

    Lee, K.L.; Arthur, A.A.; Jones, R.W.; Matis, H.S.; Nakamura, M.; Kleinfelder, S.A.; Ritter, H.G.; Wienman, H.H.

    1990-01-01

    This paper describes the multiplexing scheme of custom CMOS analog memory integrated circuits, 16 channels x 256 cells, into analog to digital converters (ADC's) to handle 15,360 signal channels of a time projection, chamber detector system. Primary requirements of this system are high density, low power and large dynamic range. The analog memory device multiplexing scheme was designed to digitize the information stored in the memory cells. The digitization time of the ADC's and the settling times for the memory unit were carefully interleaved to optimize the performance and timing during the multiplexing operation. This kept the total number of ADC's, a costly and power dissipative component, to an acceptable minimum

  13. From Analog to Digital Medias in Early Childhood Education

    DEFF Research Database (Denmark)

    Brandt, Erika Zimmer

    2015-01-01

    Research aims: The aim of the study is to explore how the encounters between children and their educators alter when the media changes from analog to digital. Relationship to previous research works Tablets and other handheld, electronic devices has become part of everyday life in kindergartens...... Considerations: A changed media environment reveals a kind of social vacuum. Educators find themselves lacking norms for how to interact in this new reality. This lack of knowhow and experience in this specific area of professionalism creates uncertainty and vulnerability in the informants which require micro...... ethical considerations. Main finding or discussion: The choice of media in educational practice seems to affect not only the horizon of possible topics in dialogue between children and their educators but also seem to affect the ways that topics are being introduced and discussed in the dialogue...

  14. Analog-to-digital conversion to accommodate the dynamics of live music in hearing instruments.

    Science.gov (United States)

    Hockley, Neil S; Bahlmann, Frauke; Fulton, Bernadette

    2012-09-01

    Hearing instrument design focuses on the amplification of speech to reduce the negative effects of hearing loss. Many amateur and professional musicians, along with music enthusiasts, also require their hearing instruments to perform well when listening to the frequent, high amplitude peaks of live music. One limitation, in most current digital hearing instruments with 16-bit analog-to-digital (A/D) converters, is that the compressor before the A/D conversion is limited to 95 dB (SPL) or less at the input. This is more than adequate for the dynamic range of speech; however, this does not accommodate the amplitude peaks present in live music. The hearing instrument input compression system can be adjusted to accommodate for the amplitudes present in music that would otherwise be compressed before the A/D converter in the hearing instrument. The methodology behind this technological approach will be presented along with measurements to demonstrate its effectiveness.

  15. Transitioning from Analog to Digital Audio Recording in Childhood Speech Sound Disorders

    Science.gov (United States)

    Shriberg, Lawrence D.; Mcsweeny, Jane L.; Anderson, Bruce E.; Campbell, Thomas F.; Chial, Michael R.; Green, Jordan R.; Hauner, Katherina K.; Moore, Christopher A.; Rusiewicz, Heather L.; Wilson, David L.

    2005-01-01

    Few empirical findings or technical guidelines are available on the current transition from analog to digital audio recording in childhood speech sound disorders. Of particular concern in the present context was whether a transition from analog- to digital-based transcription and coding of prosody and voice features might require re-standardizing…

  16. Quarter-Rate Superconducting Modulator for Improved High Resolution Analog-to-Digital Converter

    National Research Council Canada - National Science Library

    Inamdar, Amol; Rylov, Sergey; Sahu, Anubhav; Sarwana, Saad; Gupta, Deepnarayan

    2006-01-01

    .... In a PMD ADC, the analog input signal modulates the phase of a periodic stream of fluxons applied to a modulator circuit for subsequent demodulation in a clocked synchronizer circuit to produce a digital code...

  17. Design of Pipeline Analog-To-Digital Converters Via Geometric Programming

    National Research Council Canada - National Science Library

    Hershenson, Maria

    2002-01-01

    .... This method computes the sizes of the different components (transistors, capacitors, etc.) in a predefined ADC topology so that the design specifications are met in the desired process technology...

  18. Optically Assisted Analog-to-Digital Converter for Next Generation "Software Defined" Radios, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Next generation commercial and DoD communication systems must meet the demand for higher data rates and the growing number of users in an increasingly over-taxed...

  19. Comparison of performance of analog-to-digital converters (ADC) for pulse height analyzers

    International Nuclear Information System (INIS)

    Suzuki, Shogo; Hirai, Shoji

    1981-01-01

    In the recent ADCs for pulse height analyzers (PHA), Wilkinson type is a leading one, and those with 50 to 200 MHz clock frequency and 8K channel are mostly on the market. The comparison of the performance of ADCs was conducted under the condition of using these multi-channel PHAs as γ-ray spectrometers. The following three ADCs were compared: ADC incorporated in CANBERRA 8100 MCA, and CANBERRA 8060 ADCs used as the ADCs for 1st and 2nd GAMA systems. In this case, the conversion gains of these ADCs were set at 4K because the memory of 8100 MCA was 4K, and the GAMA systems were also mostly operated at 4K. In this paper, report is made on the measurements of dead time, the change of γ peaks immediately after the power was turned on, the temperature dependence of ADCs the long term stability of ADCs, derivative non-linearity, and integration non-linearity. The dead time of the ADC of 8100 CMA was shorter in the range up to 1000 channels. The temperature dependence was -0.017%/deg C in 8100 MCA, and -0.061 and -0.072%/deg C in GAMA. The long term stability was -0.02%/14 hr in 8100 MCA, and -0.027%/14 hr in 8060 of 1st GAMA. The derivative non-linearity was 0.45% in 8100 MCA, 0.67% in 8060 of 1st GAMA, and the integration non-linearity was 0.075% for 8100 MCA, and 0.085 - 0.1% in 8060 ADCs. Also, the change of γ peaks immediately after the power was turned on for 8100 ADC was better than that of 8060 ADC. (Wakatsuki, Y.)

  20. Audio Format Change From Analog to Digital Audio Using the Sony Sound Forge 9.0

    OpenAIRE

    Faisal Safrudin; Yulina Yulina, SKom, MMSI

    2007-01-01

    Changes in an audio analog to digital audio is not only useful in among the journalists or the journalists are also useful for general audiences though. In previous technology we encounter a lot of almost everyone uses the form of analog audio cassettes. Along with the development of technology, analog audio format is rarely used in the presence of digital audio, but it can be overcome by changing the format of analog audio to digital audio using Sony Sound Forge 9.0. The author will discuss ...

  1. The influence of the analog-to-digital conversion error on the JT-60 plasma position/shape feedback control system

    International Nuclear Information System (INIS)

    Yoshida, Michiharu; Kurihara, Kenichi

    1995-12-01

    In the plasma feedback control system (PFCS) and the direct digital controller (DDC) for the poloidal field coil power supply in the JT-60 tokamak, it is necessary to observe signals of all the poloidal field coil currents. Each of the signals, originally measured by a single sensor, is distributed to the PFCS and DDC through different cable routes and different analog-to-digital converters from each other. This produces the conversion error to the amount of several bits. Consequently, proper voltage from feedback calculation cannot be applied to the coil, and hence the control performance is possibly supposed to deteriorate to a certain extent. This paper describes how this error makes an influence on the plasma horizontal position control and how to improve the deteriorated control performance. (author)

  2. A 16 channel VLSI chip, containing charge amplifier and analog to digital converter, for readout of highly granular particle detectors

    NARCIS (Netherlands)

    Barlag, C; Carlen, L; El Chenawi, K; Garpman, S; Gustafsson, HA; Gustafsson, S; Heine, N; Kampert, KH; Louw, S; Lohner, H; Oskarsson, A; Otterlund, [No Value; Reygers, K; Stenlund, E; Svensson, T; Sundblad, R; Soderstrom, K; Osterman, L

    1998-01-01

    An integrated circuit for readout of particle detectors, producing a charge signal has been developed. The circuit contains 16 channels of charge integration, sample and hold amplifier, followed by an analog multiplexer. The charge content of each channel is digitized, one by one, by a 6 bit

  3. A slow-speed multiple-channel analog-to-digital data logging system

    Science.gov (United States)

    Lloyd, T. C.; Flaherty, B. J.

    1973-01-01

    The system was developed to record from one up to a maximum of sixteen channels of analog data onto magnetic tape. Each analog channel of data can be sampled at rates of 1, 2, 6, 12, or 60 times per minute. The system is divided into three subunits: a digital clock, an incremental magnetic tape recorder, and a sequential converter. The interfacing requirements of these subunits are presented.

  4. A new approach for digital calibration of timing-mismatch in four-channels time-interleaved analog-to-digital converters

    International Nuclear Information System (INIS)

    Majdinasab, E; Farshidi, E

    2014-01-01

    In this paper employing fractional delay filter in farrow structure and a time delay block a new approach for digital calibration is described that corrects the timing mismatch between four interleaved channels. Fractional delay filter is a good candidate for bandlimited interpolation between samples and farrow structure filter is an efficient way to implement interpolation filter in which Lagrange polynomial approximation method is used for arbitrary sample rate change. In this work, the proposed method is employed for a four-channel ADC and can be applied for an arbitrary number of parallel channels. Simulation results show that after 40 ksamples, the mismatch error converges in detector and spurious components are suppressed after calibration by more than 40 dB

  5. Analog-to-digital interface and real-time measurement of the phase volume of a beam using an ''elektronika-1001'' computer

    International Nuclear Information System (INIS)

    Batkin, V.I.; Getmanov, V.N.

    1984-01-01

    The authors describe a system for multichannel exchange of analog and digital signals between an Elektronika 100I computer and experimental hardware via noise-immune connecting lines. Diagrams illustrate the analog-to-digital interface and the connections between that interface and a multiwire secondary-emission profile detector. The dynamic measurement range of the system is 1-10 -4 pC per wire. Analog and digital data are input at 12.5 kHz and 30 kHz respectively. The time required to analyze the beam shape and make corrections is 150 microseconds. The geometric parameters of the beam are measured accurately to 20 micrometers. The angular divergence of the beam is 10 -4 rad

  6. A REVIEW OF HUMAN-SYSTEM INTERFACE DESIGN ISSUES OBSERVED DURING ANALOG-TO-DIGITAL AND DIGITAL-TO-DIGITAL MIGRATIONS IN U.S. NUCLEAR POWER PLANTS

    Energy Technology Data Exchange (ETDEWEB)

    Kovesdi, C.; Joe, J.

    2017-05-01

    The United States (U.S.) Department of Energy (DOE) Light Water Reactor Sustainability (LWRS) program is developing a scientific basis through targeted research and development (R&D) to support the U.S. nuclear power plant (NPP) fleet in extending their existing licensing period and ensuring their long-term reliability, productivity, safety, and security. Over the last several years, human factors engineering (HFE) professionals at the Idaho National Laboratory (INL) have supported the LWRS Advanced Instrumentation, Information, and Control (II&C) System Technologies pathway across several U.S. commercial NPPs in analog-to-digital migrations (i.e., turbine control systems) and digital-to-digital migrations (i.e., Safety Parameter Display System). These efforts have included in-depth human factors evaluation of proposed human-system interface (HSI) design concepts against established U.S. Nuclear Regulatory Commission (NRC) design guidelines from NUREG-0700, Rev 2 to inform subsequent HSI design prior to transitioning into Verification and Validation. This paper discusses some of the overarching design issues observed from these past HFE evaluations. In addition, this work presents some observed challenges such as common tradeoffs utilities are likely to face when introducing new HSI technologies into NPP hybrid control rooms. The primary purpose of this work is to distill these observed design issues into general HSI design guidance that industry can use in early stages of HSI design.

  7. Analog-digital converters for industrial applications including an introduction to digital-analog converters

    CERN Document Server

    Ohnhäuser, Frank

    2015-01-01

    This book offers students and those new to the topic of analog-to-digital converters (ADCs) a broad introduction, before going into details of the state-of-the-art design techniques for SAR and DS converters, including the latest research topics, which are valuable for IC design engineers as well as users of ADCs in applications. The book then addresses important topics, such as correct connectivity of ADCs in an application, the verification, characterization and testing of ADCs that ensure high-quality end products. Analog-to-digital converters are the central element in any data processing system and regulation loops such as modems or electrical motor drives. They significantly affect the performance and resolution of a system or end product. System development engineers need to be familiar with the performance parameters of the converters and understand the advantages and disadvantages of the various architectures. Integrated circuit development engineers have to overcome the problem of achieving high per...

  8. Simplified design of data converters

    CERN Document Server

    Lenk, John

    1997-01-01

    Simplified Design of Data Converters shows how to design and experiment with data converters, both analog-to-digital and digital to analog. The design approach here is the same one used in all of John Lenk's best-selling books on simplified and practical design. Throughout the book, design problems start with guidelines for selecting all components on a trial-value basis, assuming a specific design goal and set of conditions. Then, using the guideline values in experimental circuits, the desired results are produced by varying the experimental component values, if needed.If you are a w

  9. A Methodology to Teach Advanced A/D Converters, Combining Digital Signal Processing and Microelectronics Perspectives

    Science.gov (United States)

    Quintans, C.; Colmenar, A.; Castro, M.; Moure, M. J.; Mandado, E.

    2010-01-01

    ADCs (analog-to-digital converters), especially Pipeline and Sigma-Delta converters, are designed using complex architectures in order to increase their sampling rate and/or resolution. Consequently, the learning of ADC devices also encompasses complex concepts such as multistage synchronization, latency, oversampling, modulation, noise shaping,…

  10. Method for Converter Synchronization with RF Injection

    OpenAIRE

    Joshua P. Bruckmeyer; Ivica Kostanic

    2015-01-01

    This paper presents an injection method for synchronizing analog to digital converters (ADC). This approach can eliminate the need for precision routed discrete synchronization signals of current technologies, such as JESD204. By eliminating the setup and hold time requirements at the conversion (or near conversion) clock rate, higher sample rate systems can be synchronized. Measured data from an existing multiple ADC conversion system was used to evaluate the method. Coherent beams were simu...

  11. Restructuring of a flash A/D converter to improve SEU rad tolerance

    International Nuclear Information System (INIS)

    Monnier, T.; Roche, R.M.; Corbiere, F.

    1999-01-01

    The purpose of this work is to present how structural changes in the conventional Flash Analog to Digital Converter can secure it for a harsh radiation environment. The method consists in a coupling of two complementary techniques: a robust reconfiguration of the logical structure joined to a design hardening of the individual blocks. This approach preserves the ADC performances. (authors)

  12. Control of AC–DC grid side converter with single AC current sensor

    Indian Academy of Sciences (India)

    Himanshu Misra

    2017-11-24

    Nov 24, 2017 ... Introduction. Three-phase grid-connected pulse width modulation (PWM) converters have widespread applications such as motor drives, UPS, power quality conditioners and DFIG [1]. ..... in a-axis grid current (due to sensor and analog to digital .... current is proportional to the difference between refer-.

  13. Wide-range charge-to-digital converter for a large-volume Cherenkov detector

    International Nuclear Information System (INIS)

    Potapov, G.A.; Penin, I.V.

    1986-01-01

    Block-diagram of the three-channel FEhU-49B converter of short-range pulse-response for Cherenkov radiation in the 10 6 dynamic range supplied to the input of the K113PV1 10-digit analog-to-digital converter is considered. The converter comprises three analog coordination systems, a system for selection and commutation of data channel and an analog-to-digital converter. The analog data channel represents in-series communication of three-cascade integrating amplifier and a two-cascade amplitude detector. The coefficient of analog channel conversion equals 400 mV/pC. Minimum duration of registered pulses is 10 ns. The equated noise is 200 nA. The dynamic range of channel linearity is 10 3 . The detection threshold of the peak detector is 10 mV. Delay time of information dinode commutation is 200 ns

  14. Data Converter for Multistandard Mobile Phones

    DEFF Research Database (Denmark)

    Yurttas, Aziz; Bruun, Erik; Jensen, Rasmus Glarborg

    2004-01-01

    This paper describes an analog to digital converter (ADC) for mobile communication systems using a direct down conversion architecture. The ADC can be programmed to meet the requirements of different communication standards, including GSM (Global System for Mobile communication) and WCDMA (Wideband....... The entire ADC consumes about 5.5 mW and occupies an active area of about 0.36 mm(2). A test circuit has been developed and fabricated and measurements show that both the required programmability and the required performance can be obtained using the proposed configurations....

  15. CMOS sigma-delta converters practical design guide

    CERN Document Server

    De la Rosa, Jose M

    2013-01-01

    A comprehensive overview of Sigma-Delta Analog-to-Digital Converters (ADCs) and a practical guide to their design in nano-scale CMOS for optimal performance. This book presents a systematic and comprehensive compilation of sigma-delta converter operating principles, the new advances in architectures and circuits, design methodologies and practical considerations - going from system-level specifications to silicon integration, packaging and measurements, with emphasis on nanometer CMOS implementation. The book emphasizes practical design issues - from high-level behavioural modelling i

  16. Conception and realization of a multichannel amplitude converter

    International Nuclear Information System (INIS)

    Bendebiche, L.

    1992-11-01

    A compact Analog to Digital Converter system suitable for high resolution γ-ray analysers has been developed based on the ADADC84 12-bit converter from Analog Devices. The converter was equipped with a peak detector and a stretcher, and with a memory card providing the sliding scale circuits, the lower threshold, the channel number identification and the zero suppression. The conversion time is 10 μs and the differential non linearity is less than ±1% for a 12-bit resolution. The converter consists of a 12-bit spectroscopy analog-to-digital converter (ADC) while the memory card includes a 8K 24-bit buffer memory. The two cards are plugged into a slot of an IBM PC AT and using an emulation software converts the micro-computer into a full-featured pulse height analyser. In data acquisition mode, the cards can operate independently, making the computer free for other tasks. The software offers acquisition control, visualization, data handling functions and various types of result presentation

  17. Large-scale digitizer system, analog converters

    International Nuclear Information System (INIS)

    Althaus, R.F.; Lee, K.L.; Kirsten, F.A.; Wagner, L.J.

    1976-10-01

    Analog to digital converter circuits that are based on the sharing of common resources, including those which are critical to the linearity and stability of the individual channels, are described. Simplicity of circuit composition is valued over other more costly approaches. These are intended to be applied in a large-scale processing and digitizing system for use with high-energy physics detectors such as drift-chambers or phototube-scintillator arrays. Signal distribution techniques are of paramount importance in maintaining adequate signal-to-noise ratio. Noise in both amplitude and time-jitter senses is held sufficiently low so that conversions with 10-bit charge resolution and 12-bit time resolution are achieved

  18. Understanding delta-sigma data converters

    CERN Document Server

    Pavan, Shanti; Temes, Gabor C

    2017-01-01

    This new edition introduces novel analysis and design techniques for delta-sigma (ΔΣ) converters in physical and conceptual terms, and includes new chapters that explore developments in the field over the last decade. This book explains the principles and operation of delta-sigma analog-to-digital converters (ADCs) in physical and conceptual terms in accordance with the most recent developments in the field. The interest of ΔΣ converter designers has shifted significantly over the past decade, due to many new applications for data converters at the far ends of the frequency spectrum. Continuous-time delta-sigma A/D converters with GHz clocks, of both lowpass and bandpass types, are required for wireless applications. At the other extreme, multiplexed ADCs with very narrow (sometimes 10 Hz wide) signal bandwidths, but very high accuracy are needed in the interfaces of biomedical and environmental sensors. To reflect the changing eeds of designers, the second edition includes significant new material on bo...

  19. Inverter-based successive approximation capacitance-to-digital converter

    KAUST Repository

    Omran, Hesham

    2017-03-23

    An energy-efficient capacitance-to-digital converter (CDC) is provided that utilizes a capacitance-domain successive approximation (SAR) technique. Unlike SAR analog- to-digital converters (ADCs), analysis shows that for SAR CDCs, the comparator offset voltage will result in signal-dependent and parasitic-dependent conversion errors, which necessitates an op-amp-based implementation. The inverter-based SAR CDC contemplated herein provides robust, energy-efficient, and fast operation. The inverter- based SAR CDC may include a hybrid coarse-fine programmable capacitor array. The design of example embodiments is insensitive to analog references, and thus achieves very low temperature sensitivity without the need for calibration. Moreover, this design achieves improved energy efficiency.

  20. Capacitive digital-to-analogue converters with least significant bit down in differential successive approximation register ADCs

    Directory of Open Access Journals (Sweden)

    Lei Sun

    2014-01-01

    Full Text Available This Letter proposes a least significant bit-down switching scheme in the capacitive digital-to-analogue converters (CDACs of successive approximation register analog-to-digital converter (ADC. Under the same unit capacitor, the chip area and the switching energy are halved without increasing the complexity of logic circuits. Compared with conventional CDAC, when it is applied to one of the most efficient switching schemes, V(cm-based structure, it achieves 93% less switching energy and 75% less chip area with the same differential non linearity (DNL/integral non linearity (INL performance.

  1. Conversion of a servomanipulator from analog to digital control

    International Nuclear Information System (INIS)

    Killough, S.M.; Martin, H.L.; Hamel, W.R.

    1986-01-01

    Oak Ridge National Laboratory (ORNL) has developed expertise in computer control of force-reflecting master/slave servomanipulators as a result of research for the Consolidated Fuel Reprocessing Program. These computer control capabilities have been applied to a commercially available servomanipulator, the TeleOperator Systems SM-229. All of the servo drive and control circuitry has been replaced with commercially available digital controls and amplifiers, and a customer software - package has been developed at ORNL. This conversion to digital computer control resulted in significant improvements in force-reflection characteristics, ease of operation, diagnostic capabilities, indexing features, and potential increased reliability. The system will be used at the Tokamak Fusion Test Reactor at the Princeton Plasma Physics Laboratory (PPPL) for maintenance demonstrations

  2. Analog-to-Digital Cognitive Radio: Sampling, Detection, and Hardware

    Science.gov (United States)

    Cohen, Deborah; Tsiper, Shahar; Eldar, Yonina C.

    2018-01-01

    The proliferation of wireless communications has recently created a bottleneck in terms of spectrum availability. Motivated by the observation that the root of the spectrum scarcity is not a lack of resources but an inefficient managing that can be solved, dynamic opportunistic exploitation of spectral bands has been considered, under the name of Cognitive Radio (CR). This technology allows secondary users to access currently idle spectral bands by detecting and tracking the spectrum occupancy. The CR application revisits this traditional task with specific and severe requirements in terms of spectrum sensing and detection performance, real-time processing, robustness to noise and more. Unfortunately, conventional methods do not satisfy these demands for typical signals, that often have very high Nyquist rates. Recently, several sampling methods have been proposed that exploit signals' a priori known structure to sample them below the Nyquist rate. Here, we review some of these techniques and tie them to the task of spectrum sensing in the context of CR. We then show how issues related to spectrum sensing can be tackled in the sub-Nyquist regime. First, to cope with low signal to noise ratios, we propose to recover second-order statistics from the low rate samples, rather than the signal itself. In particular, we consider cyclostationary based detection, and investigate CR networks that perform collaborative spectrum sensing to overcome channel effects. To enhance the efficiency of the available spectral bands detection, we present joint spectrum sensing and direction of arrival estimation methods. Throughout this work, we highlight the relation between theoretical algorithms and their practical implementation. We show hardware simulations performed on a prototype we built, demonstrating the feasibility of sub-Nyquist spectrum sensing in the context of CR.

  3. Nyquist AD Converters, Sensor Interfaces, and Robustness Advances in Analog Circuit Design, 2012

    CERN Document Server

    Baschirotto, Andrea; Steyaert, Michiel

    2013-01-01

    This book is based on the presentations during the 21st workshop on Advances in Analog Circuit Design.  Expert designers provide readers with information about a variety of topics at the frontier of analog circuit design, including Nyquist analog-to-digital converters, capacitive sensor interfaces, reliability, variability, and connectivity.  This book serves as a valuable reference to the state-of-the-art, for anyone involved in analog circuit research and development.  Provides a state-of-the-art reference in analog circuit design, written by experts from industry and academia; Presents material in a tutorial-based format; Includes coverage of Nyquist A/D converters, capacitive sensor interfaces, reliability, variability, and connectivity.

  4. Data Converter

    NARCIS (Netherlands)

    Schinkel, Daniel

    2006-01-01

    A data converter comprises a discrete-time sigma delta modulator e.g. for driving a Class-D power amplifier. The low-pass filter of the sigma delta modulator is modified by adding a suitably positioned pole to lower the oscillation frequency (limit cycle) of the sigma delta modulator in order to

  5. Data Converter

    NARCIS (Netherlands)

    Schinkel, Daniel

    2005-01-01

    A data converter comprises a discrete-time sigma delta modulator e.g. for driving a Class-D power amplifier. The low-pass filter of the sigma delta modulator is modified by adding a suitably positioned pole to lower the oscillation frequency (limit cycle) of the sigma delta modulator in order to

  6. Data Converter

    NARCIS (Netherlands)

    Schinkel, Daniel; Nuijten, Petrus A.C.M.

    2005-01-01

    A data converter comprises a discrete- time sigma delta modulator e.g. for driving a Class-D power amplifier. The low-pass filter of the sigma delta modulator is modified by adding a suitably positioned pole to lower the oscillation frequency (limit cycle) of the sigma delta modulator in order to

  7. Hydrogen converters

    International Nuclear Information System (INIS)

    Mondino, Angel V.

    2003-01-01

    The National Atomic Energy Commission of Argentina developed a process of 99 Mo production from fission, based on irradiation of uranium aluminide targets with thermal neutrons in the RA-3 reactor of the Ezeiza Atomic Centre. These targets are afterwards dissolved in an alkaline solution, with the consequent liberation of hydrogen as the main gaseous residue. This work deals with the use of a first model of metallic converter and a later prototype of glass converter at laboratory scale, adjusted to the requirements and conditions of the specific redox process. Oxidized copper wires were used, which were reduced to elementary copper at 400 C degrees and then regenerated by oxidation with hot air. Details of the bed structure and the operation conditions are also provided. The equipment required for the assembling in cells is minimal and, taking into account the operation final temperature and the purge with nitrogen, the procedure is totally safe. Finally, the results are extrapolated for the design of a converter to be used in a hot cell. (author)

  8. Ray converter

    International Nuclear Information System (INIS)

    Reiss, K.H.

    1976-01-01

    In a radiographic system a converter is used for changing image forming intensity distribution in a bundle of penetrating rays into a flow of electrically charged particles by electrodes located in a gas space and partly latticed (grids) which lie at potentials stepped from cathode to anode. The invention is particularly characterized by the provision of at least two grids extending between and parallel to the cathode and the anode. The electrical field which lies between two electrodes lies at least between the grids located closest to the cathode being to the extent of between 1 and 10 percent, in the average preferably 3 percent below the electrical break down field in the gas in a homogeneous electrical field

  9. β-expansion attractors observed in A/D converters

    Science.gov (United States)

    Kohda, Tohru; Horio, Yoshihiko; Aihara, Kazuyuki

    2012-12-01

    The recently proposed β-encoders, analog-to-digital converters using an amplifier with a factor β and a flaky quantizer with threshold ν, have proven to be explained by the deterministic dynamics of multi-valued Rényi-Parry maps. Such a map is locally eventually onto [ν-1, ν), which is topologically conjugate to Parry's (β,α)-map with α =(β-1)(ν-1). This implies that β-encoders have a closed subinterval [ν-1,ν), which includes an attractor. Thus, the iteration of the multi-valued Rényi-Parry map performs the β-expansion of x while quantization errors in β-encoders behave chaotically and do not converge to a fixed point. This β-expansion attractor is relatively simpler than previously reported attractors. The object of this paper is twofold: to observe the embedded attractors in the β-encoder and to identify attractors that are useful for spread-spectrum codes and optimization techniques using pseudo-random numbers.

  10. Design of a Single Channel Modulated Wideband Converter for Wideband Spectrum Sensing: Theory, Architecture and Hardware Implementation.

    Science.gov (United States)

    Liu, Weisong; Huang, Zhitao; Wang, Xiang; Sun, Weichao

    2017-05-04

    In a cognitive radio sensor network (CRSN), wideband spectrum sensing devices which aims to effectively exploit temporarily vacant spectrum intervals as soon as possible are of great importance. However, the challenge of increasingly high signal frequency and wide bandwidth requires an extremely high sampling rate which may exceed today's best analog-to-digital converters (ADCs) front-end bandwidth. Recently, the newly proposed architecture called modulated wideband converter (MWC), is an attractive analog compressed sensing technique that can highly reduce the sampling rate. However, the MWC has high hardware complexity owing to its parallel channel structure especially when the number of signals increases. In this paper, we propose a single channel modulated wideband converter (SCMWC) scheme for spectrum sensing of band-limited wide-sense stationary (WSS) signals. With one antenna or sensor, this scheme can save not only sampling rate but also hardware complexity. We then present a new, SCMWC based, single node CR prototype System, on which the spectrum sensing algorithm was tested. Experiments on our hardware prototype show that the proposed architecture leads to successful spectrum sensing. And the total sampling rate as well as hardware size is only one channel's consumption of MWC.

  11. Wavelength converter technology

    DEFF Research Database (Denmark)

    Kloch, Allan; Hansen, Peter Bukhave; Poulsen, Henrik Nørskov

    1999-01-01

    Wavelength conversion is important since it ensures full flexibility of the WDM network layer. Progress in optical wavelength converter technology is reviewed with emphasis on all-optical wavelength converter types based on semiconductor optical amplifiers.......Wavelength conversion is important since it ensures full flexibility of the WDM network layer. Progress in optical wavelength converter technology is reviewed with emphasis on all-optical wavelength converter types based on semiconductor optical amplifiers....

  12. Wavelength converter technology

    DEFF Research Database (Denmark)

    Kloch, Allan; Hansen, Peter Bukhave; Poulsen, Henrik Nørskov

    1999-01-01

    Wavelength conversion is important since it ensures full flexibility of the WDM network layer. Progress in optical wavelength converter technology is reviewed with emphasis on air-optical wavelength converter types based on semiconductor optical amplifiers.......Wavelength conversion is important since it ensures full flexibility of the WDM network layer. Progress in optical wavelength converter technology is reviewed with emphasis on air-optical wavelength converter types based on semiconductor optical amplifiers....

  13. Technologies for converter topologies

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Yan; Zhang, Haiyu

    2017-02-28

    In some embodiments of the disclosed inverter topologies, an inverter may include a full bridge LLC resonant converter, a first boost converter, and a second boost converter. In such embodiments, the first and second boost converters operate in an interleaved manner. In other disclosed embodiments, the inverter may include a half-bridge inverter circuit, a resonant circuit, a capacitor divider circuit, and a transformer.

  14. Josephson stroboscopic converters. Review

    International Nuclear Information System (INIS)

    Askerzade, I.N.

    2006-01-01

    One reviews studies dealing with the Josephson stroboscopic converters. One analyzed dynamic properties of the Josephson junctions serving as sensitive comparators in converters. One elaborates a theory to evaluate time resolution and sensitivity of the Josephson comparators. One derived analytical formulae for the limiting characteristics of superconductors of strobe-converters. One discusses peculiar features of strobe-converters on the basis of high-temperature superconductors. Evaluations show feasibility of designing of strobe-converters with subpicosecond time resolution and nanoampere sensitivity [ru

  15. Compact FPGA-based beamformer using oversampled 1-bit A/D converters.

    Science.gov (United States)

    Tomov, Borislav Gueorguiev; Jensen, Jørgen Arendt

    2005-05-01

    A compact medical ultrasound beamformer architecture that uses oversampled 1-bit analog-to-digital (A/D) converters is presented. Sparse sample processing is used, as the echo signal for the image lines is reconstructed in 512 equidistant focal points along the line through its in-phase and quadrature components. That information is sufficient for presenting a B-mode image and creating a color flow map. The high sampling rate provides the necessary delay resolution for the focusing. The low channel data width (1-bit) makes it possible to construct a compact beamformer logic. The signal reconstruction is done using finite impulse reponse (FIR) filters, applied on selected bit sequences of the delta-sigma modulator output stream. The approach allows for a multichannel beamformer to fit in a single field programmable gate array (FPGA) device. A 32-channel beamformer is estimated to occupy 50% of the available logic resources in a commercially available mid-range FPGA, and to be able to operate at 129 MHz. Simulation of the architecture at 140 MHz provides images with a dynamic range approaching 60 dB for an excitation frequency of 3 MHz.

  16. The photoelectric displacement converter

    Science.gov (United States)

    Dragoner, Valeriu V.

    2005-02-01

    In the article are examined questions of constructing photoelectric displacement converter satisfying demands that are stated above. Converter has channels of approximate and precise readings. The approximate reading may be accomplished either by the method of reading from a code mask or by the method of the consecutive calculation of optical scale gaps number. Phase interpolator of mouar strips" gaps is determined as a precise measuring. It is shown mathematical model of converter that allow evaluating errors and operating speed of conversion.

  17. Interleaved power converter

    Science.gov (United States)

    Zhu, Lizhi

    2007-11-13

    A power converter architecture interleaves full bridge converters to alleviate thermal management problems in high current applications, and may, for example, double the output power capability while reducing parts count and costs. For example, one phase of a three phase inverter is shared between two transformers, which provide power to a rectifier such as a current doubler rectifier to provide two full bridge DC/DC converters with three rather than four high voltage inverter legs.

  18. Power converters definitions, classification and converter topologies

    CERN Document Server

    Bordry, Frederick

    2006-01-01

    This paper introduces power conversion principles and defines the terminology. The concepts of sources and switches are defined and classified. From the basic laws of source interconnections, a generic method of power converter synthesis is presented. Some examples illustrate this systematic method. Finally, the notions of commutation cell and soft commutation are introduced and discussed.

  19. Analog-to-digital conversion using custom CMOS analog memory for the EOS time projection chamber

    International Nuclear Information System (INIS)

    Lee, K.L.; Arthur, A.A.; Jones, R.W.; Matis, H.S.; Nakamura, M.; Kleinfelder, S.A.; Ritter, H.G.; Wieman, H.H.

    1991-01-01

    This paper reports on an expert system for generating control rod patterns that has been developed. The knowledge is transformed into IF-THEN rules. The inference engine uses the Rete pattern matching algorithm to match facts, and rule premises and conflict resolution strategies to make the system function intelligently. A forward-chaining mechanism is adopted in the inference engine. The system is implemented in the Common Lisp programming language. The three-dimensional core simulation model performs the core status and burnup calculations. The system is successfully demonstrated by generating control rod programming for the 2894-MW (thermal) Kuosheng nuclear power plant in Taiwan. The computing time is tremendously reduced compared to programs using mathematical methods

  20. Analog-to-digital conversion of spectrometric data in information-control systems of activation analysis

    International Nuclear Information System (INIS)

    Mamonov, E.I.

    1972-01-01

    Analogue-digital conversion (ADC) techniques in nuclear radiation spectrometer channels is a most important link of information control systems in activation analysis. For the development of the ADC of spectrometer channels logico-structural methods of increasing the capacity, procedures for boosting frequency modes and improving the accuracy are promising. Procedures are suggested for increasing the ADC capacity. Insufficient stability and noticeable non-linearity of the spectrometer channel can be corrected at the information processing stage if their regularities are known. Capacity limitations make the development of ADC featuring high stability, capacity and linearity quite urgent

  1. Sensor Interfaces for Private Home Automation: From Analog to Digital, Wireless and Autonomous

    Directory of Open Access Journals (Sweden)

    Erich Leder

    2007-08-01

    Full Text Available In this paper a flexible and reliable system for smart home automation is presented. It is based on standardized hardware and open source communication protocols. Firstly, a special sensor interface has been developed, which allows the measurement of (slow analog signals to be determined by inexpensive digital PLC input terminals. Right now, up to eleven different modules have been implemented and the system is being tested in several configurations. In a second step, the communication is digitized. With the digitalization of the sensor modules, based on the implementation of a PIC Microcontroller, more intelligence is provided to the module, which increases the power and flexibility of the whole system. Thirdly, a wireless sensor-system consisting of a base station and of a mobile measuring unit is developed. The autonomous mobile unit is realized by using solar powering, gold cap energy storage, low-power circuits and a radio communication interface.

  2. Advanced dcdc converters

    CERN Document Server

    Luo, Fang Lin

    2003-01-01

    DC/DC conversion techniques have undergone rapid development in recent decades. With the pioneering work of these authors, DC/DC converters have now moved into their sixth generation. This book offers a concise, practical presentation of DC/DC converters, summarizing the spectrum of conversion tecnologies and presentingmany new ideas and more than 100 new topologies. Nowhere else in the literature are DC/DC converters so logically sorted and systematically introduced, and nowhere else can readers find detailed information on prototype topologies that represent a major contribution to modern power engineering. More than 320 figures, 60 tables, and 500 formulae facilitate understand and provide precise data.

  3. Improving Power Converter Reliability

    DEFF Research Database (Denmark)

    Ghimire, Pramod; de Vega, Angel Ruiz; Beczkowski, Szymon

    2014-01-01

    The real-time junction temperature monitoring of a high-power insulated-gate bipolar transistor (IGBT) module is important to increase the overall reliability of power converters for industrial applications. This article proposes a new method to measure the on-state collector?emitter voltage...... of a high-power IGBT module during converter operation, which may play a vital role in improving the reliability of the power converters. The measured voltage is used to estimate the module average junction temperature of the high and low-voltage side of a half-bridge IGBT separately in every fundamental...

  4. Thermionic photovoltaic energy converter

    Science.gov (United States)

    Chubb, D. L. (Inventor)

    1985-01-01

    A thermionic photovoltaic energy conversion device comprises a thermionic diode mounted within a hollow tubular photovoltaic converter. The thermionic diode maintains a cesium discharge for producing excited atoms that emit line radiation in the wavelength region of 850 nm to 890 nm. The photovoltaic converter is a silicon or gallium arsenide photovoltaic cell having bandgap energies in this same wavelength region for optimum cell efficiency.

  5. Power converter design optimization

    Science.gov (United States)

    Yu, Y.; Lee, F. C. Y.; Triner, J. E.

    1977-01-01

    Utilizing the demonstrated capability of nonlinear programming algorithms, a practical design optimization approach for power converters is established to conceive a design to meet all power-circuit performance requirements and concurrently optimize a defined quantity such as weight or losses. In addition, to facilitate a cost-effective design, the computer-aided approach provides a means to readily assess (1) the weight-efficiency tradeoff, (2) impacts of converter requirements and component characteristics on a given design, and (3) optimum power system configurations.

  6. Angiotensin-converting enzyme

    DEFF Research Database (Denmark)

    Sørensen, P G; Rømer, F K; Cortes, D

    1984-01-01

    In order to evaluate bleomycin-associated lung damage in humans, lung function parameters and serum levels of the endothelial-bound angiotensin-converting enzyme (ACE) were determined by serial measurements in 11 patients who were treated for testicular cancer. None developed clinical or radiolog......In order to evaluate bleomycin-associated lung damage in humans, lung function parameters and serum levels of the endothelial-bound angiotensin-converting enzyme (ACE) were determined by serial measurements in 11 patients who were treated for testicular cancer. None developed clinical...

  7. An Electromagnetic Beam Converter

    DEFF Research Database (Denmark)

    2009-01-01

    The present invention relates to an electromagnetic beam converter and a method for conversion of an input beam of electromagnetic radiation having a bell shaped intensity profile a(x,y) into an output beam having a prescribed target intensity profile l(x',y') based on a further development...

  8. Definition of Power Converters

    CERN Document Server

    Bordry, F

    2015-01-01

    The paper is intended to introduce power conversion principles and to define common terms in the domain. The concept s of sources and switches are defined and classified. From the basic laws of source interconnections, a generic method of power converter synthesis is presented. Some examples illustrate this systematic method. Finally, the commutation cell and soft commuta tion are introduced and discussedd.

  9. SSG Wave Energy Converter

    DEFF Research Database (Denmark)

    Margheritini, Lucia; Vicinanza, Diego; Frigaard, Peter

    2008-01-01

    The SSG (Sea Slot-cone Generator) is a wave energy converter of the overtopping type. The structure consists of a number of reservoirs one on the top of each others above the mean water level, in which the water of incoming waves is stored temporary. In each reservoir, expressively designed low h...

  10. Converting the reset

    NARCIS (Netherlands)

    J.K. Hoogland (Jiri); C.D.D. Neumann; D. Bloch

    2001-01-01

    textabstractWe give a simple algorithm to incorporate the effects of resets in convertible bond prices, without having to add an extra factor to take into account the value of the reset. Furthermore we show that the effect of a notice period, and additional make-whole features, can be treated in a

  11. The Convertible Arbitrage Strategy Analyzed

    NARCIS (Netherlands)

    Loncarski, I.; Ter Horst, J.R.; Veld, C.H.

    2006-01-01

    This paper analyzes convertible bond arbitrage on the Canadian market for the period 1998 to 2004.Convertible bond arbitrage is the combination of a long position in convertible bonds and a short position in the underlying stocks. Convertible arbitrage has been one of the most successful strategies

  12. Microprocessor controlled static converter

    Directory of Open Access Journals (Sweden)

    Stefan Szabo

    2005-10-01

    Full Text Available This paper wants to demonstrate a way of implementing a microcontroller into an DC motor speed control loop. The static power converter is a fully controlled rectifier bridge, using standard SCR's. The bridge's control signals are supplied by the microcontroller and are phase-angle or burst types. The automation loop contains a software PI-style regulator. All the experimental results shows that this aproach is flexibile enough to be used on a large scale.

  13. Resonant power converters

    CERN Document Server

    Kazimierczuk, Marian K

    2012-01-01

    This book is devoted to resonant energy conversion in power electronics. It is a practical, systematic guide to the analysis and design of various dc-dc resonant inverters, high-frequency rectifiers, and dc-dc resonant converters that are building blocks of many of today's high-frequency energy processors. Designed to function as both a superior senior-to-graduate level textbook for electrical engineering courses and a valuable professional reference for practicing engineers, it provides students and engineers with a solid grasp of existing high-frequency technology, while acquainting them wit

  14. Cycloidal Wave Energy Converter

    Energy Technology Data Exchange (ETDEWEB)

    Stefan G. Siegel, Ph.D.

    2012-11-30

    This program allowed further advancing the development of a novel type of wave energy converter, a Cycloidal Wave Energy Converter or CycWEC. A CycWEC consists of one or more hydrofoils rotating around a central shaft, and operates fully submerged beneath the water surface. It operates under feedback control sensing the incoming waves, and converts wave power to shaft power directly without any intermediate power take off system. Previous research consisting of numerical simulations and two dimensional small 1:300 scale wave flume experiments had indicated wave cancellation efficiencies beyond 95%. The present work was centered on construction and testing of a 1:10 scale model and conducting two testing campaigns in a three dimensional wave basin. These experiments allowed for the first time for direct measurement of electrical power generated as well as the interaction of the CycWEC in a three dimensional environment. The Atargis team successfully conducted two testing campaigns at the Texas A&M Offshore Technology Research Center and was able to demonstrate electricity generation. In addition, three dimensional wave diffraction results show the ability to achieve wave focusing, thus increasing the amount of wave power that can be extracted beyond what was expected from earlier two dimensional investigations. Numerical results showed wave cancellation efficiencies for irregular waves to be on par with results for regular waves over a wide range of wave lengths. Using the results from previous simulations and experiments a full scale prototype was designed and its performance in a North Atlantic wave climate of average 30kW/m of wave crest was estimated. A full scale WEC with a blade span of 150m will deliver a design power of 5MW at an estimated levelized cost of energy (LCOE) in the range of 10-17 US cents per kWh. Based on the new results achieved in the 1:10 scale experiments these estimates appear conservative and the likely performance at full scale will

  15. X-Y Converter Family

    DEFF Research Database (Denmark)

    Bhaskar, Mahajan Sagar; Sanjeevikumar, Padmanaban; Wheeler, Patrick

    2016-01-01

    system, high voltage automotive applications and industrial drives. Compared to the traditional boost converter and existing recent converters, the proposed XY converter family has the ability to provide a higher output voltage by using less number of power devices and reactive components. Other distinct......A New breed of a buck boost converter, named as the XY converter family is proposed in this article. In the XY family, 16 topologies are presented which are highly suitable for renewable energy applications which require a high ratio of DC-DC converter; such as a photovoltaic multilevel inverter...... features of the XY converter family are i) Single control switch ii) Provide negative output voltage iii) Non-isolated topologies iv) High conversion ratio without making the use of high duty cycle and v) modular structure. XY family is compared with the recent high step-up converters and the detailed...

  16. Manufacturing method of photoelectric converter

    Energy Technology Data Exchange (ETDEWEB)

    Yamazaki, Shunpei; Suzuki, Kunio; Fukada, Takeshi; Kanehana, Mikio

    1987-06-25

    This is a photoelectric converter wherein a photoelectromotive force is generated by utilizing the shorter wavelength side by the 1st converter and by utilizing the longer wavelength side by the 2nd converter; as a whole, wider wavelength range of light can be converted into electricity. In the 1st. converter, an electrode on the side of semi-incident surface is made transparent as well as an electrode equipped on the back of a non-mono-crystalline semiconductor. Light which passed this is introduced into the 2nd converter to generate an electromotive force. This invention especially relates with a method of forming this 2nd converter. In preparing I-type non-mono-crystalline semiconductor among the semiconductors having PIN junction, PCVD method is used by means of ECR (Electron Cyclotron Resonance) by using a hydrogen- or halogen- added Si-semiconductor instead of using expensive Ge, etc, which are common in the conventional method. (3 figs)

  17. Power converters for ITER

    CERN Document Server

    Benfatto, I

    2006-01-01

    The International Thermonuclear Experimental Reactor (ITER) is a thermonuclear fusion experiment designed to provide long deuterium– tritium burning plasma operation. After a short description of ITER objectives, the main design parameters and the construction schedule, the paper describes the electrical characteristics of the French 400 kV grid at Cadarache: the European site proposed for ITER. Moreover, the paper describes the main requirements and features of the power converters designed for the ITER coil and additional heating power supplies, characterized by a total installed power of about 1.8 GVA, modular design with basic units up to 90 MVA continuous duty, dc currents up to 68 kA, and voltages from 1 kV to 1 MV dc.

  18. Unity power factor converter

    Science.gov (United States)

    Wester, Gene W. (Inventor)

    1980-01-01

    A unity power factor converter capable of effecting either inversion (dc-to-dc) or rectification (ac-to-dc), and capable of providing bilateral power control from a DC source (or load) through an AC transmission line to a DC load (or source) for power flow in either direction, is comprised of comparators for comparing the AC current i with an AC signal i.sub.ref (or its phase inversion) derived from the AC ports to generate control signals to operate a switch control circuit for high speed switching to shape the AC current waveform to a sine waveform, and synchronize it in phase and frequency with the AC voltage at the AC ports, by selectively switching the connections to a series inductor as required to increase or decrease the current i.

  19. Bidirectional DC/DC Converter

    Science.gov (United States)

    Pedersen, F.

    2008-09-01

    The presented bidirectional DC/DC converter design concept is a further development of an already existing converter used for low battery voltage operation.For low battery voltage operation a high efficient low parts count DC/DC converter was developed, and used in a satellite for the battery charge and battery discharge function.The converter consists in a bidirectional, non regulating DC/DC converter connected to a discharge regulating Buck converter and a charge regulating Buck converter.The Bidirectional non regulating DC/DC converter performs with relatively high efficiency even at relatively high currents, which here means up to 35Amps.This performance was obtained through the use of power MOSFET's with on- resistances of only a few mille Ohms connected to a special transformer allowing paralleling several transistor stages on the low voltage side of the transformer. The design is patent protected. Synchronous rectification leads to high efficiency at the low battery voltages considered, which was in the range 2,7- 4,3 Volt DC.The converter performs with low switching losses as zero voltage zero current switching is implemented in all switching positions of the converter.Now, the drive power needed, to switch a relatively large number of low Ohm , hence high drive capacitance, power MOSFET's using conventional drive techniques would limit the overall conversion efficiency.Therefore a resonant drive consuming considerable less power than a conventional drive circuit was implemented in the converter.To the originally built and patent protected bidirectional non regulating DC/DC converter, is added the functionality of regulation.Hereby the need for additional converter stages in form of a Charge Buck regulator and a Discharge Buck regulator is eliminated.The bidirectional DC/DC converter can be used in connection with batteries, motors, etc, where the bidirectional feature, simple design and high performance may be useful.

  20. Architectural Exploration and Design of Time-Interleaved SAR Arrays for Low-Power and High Speed A/D Converters

    Science.gov (United States)

    Saponara, Sergio; Nuzzo, Pierluigi; Nani, Claudio; van der Plas, Geert; Fanucci, Luca

    Time-interleaved (TI) analog-to-digital converters (ADCs) are frequently advocated as a power-efficient solution to realize the high sampling rates required in single-chip transceivers for the emerging communication schemes: ultra-wideband, fast serial links, cognitive-radio and software-defined radio. However, the combined effects of multiple distortion sources due to channel mismatches (bandwidth, offset, gain and timing) severely affect system performance and power consumption of a TI ADC and need to be accounted for since the earlier design phases. In this paper, system-level design of TI ADCs is addressed through a platform-based methodology, enabling effective investigation of different speed/resolution scenarios as well as the impact of parallelism on accuracy, yield, sampling-rate, area and power consumption. Design space exploration of a TI successive approximation ADC is performed top-down via Monte Carlo simulations, by exploiting behavioral models built bottom-up after characterizing feasible implementations of the main building blocks in a 90-nm 1-V CMOS process. As a result, two implementations of the TI ADC are proposed that are capable to provide an outstanding figure-of-merit below 0.15pJ/conversion-step.

  1. Advanced power electronics converters PWM converters processing AC voltages

    CERN Document Server

    dos Santos, Euzeli

    2014-01-01

    This book covers power electronics, in depth, by presenting the basic principles and application details, which can be used both as a textbook and reference book.  Introduces a new method to present power electronics converters called Power Blocks Geometry. Applicable for courses focusing on power electronics, power electronics converters, and advanced power converters. Offers a comprehensive set of simulation results to help understand the circuits presented throughout the book

  2. Integrated power electronic converters and digital control

    CERN Document Server

    Emadi, Ali; Nie, Zhong

    2009-01-01

    Non-isolated DC-DC ConvertersBuck ConverterBoost ConverterBuck-Boost ConverterIsolated DC-DC ConvertersFlyback ConverterForward ConverterPush-Pull ConverterFull-Bridge ConverterHalf-Bridge ConverterPower Factor CorrectionConcept of PFCGeneral Classification of PFC CircuitsHigh Switching Frequency Topologies for PFCApplication of PFC in Advanced Motor DrivesIntegrated Switched-Mode Power ConvertersSwitched-Mode Power SuppliesThe Concept of Integrated ConverterDefinition of Integrated Switched-Mode Power Supplies (ISMPS)Boost-Type Integrated TopologiesGeneral Structure of Boost-Type Integrated T

  3. Nanostructure Neutron Converter Layer Development

    Science.gov (United States)

    Park, Cheol (Inventor); Sauti, Godfrey (Inventor); Kang, Jin Ho (Inventor); Lowther, Sharon E. (Inventor); Thibeault, Sheila A. (Inventor); Bryant, Robert G. (Inventor)

    2016-01-01

    Methods for making a neutron converter layer are provided. The various embodiment methods enable the formation of a single layer neutron converter material. The single layer neutron converter material formed according to the various embodiments may have a high neutron absorption cross section, tailored resistivity providing a good electric field penetration with submicron particles, and a high secondary electron emission coefficient. In an embodiment method a neutron converter layer may be formed by sequential supercritical fluid metallization of a porous nanostructure aerogel or polyimide film. In another embodiment method a neutron converter layer may be formed by simultaneous supercritical fluid metallization of a porous nanostructure aerogel or polyimide film. In a further embodiment method a neutron converter layer may be formed by in-situ metalized aerogel nanostructure development.

  4. Impedance source power electronic converters

    CERN Document Server

    Liu, Yushan; Ge, Baoming; Blaabjerg, Frede; Ellabban, Omar; Loh, Poh Chiang

    2016-01-01

    Impedance Source Power Electronic Converters brings together state of the art knowledge and cutting edge techniques in various stages of research related to the ever more popular impedance source converters/inverters. Significant research efforts are underway to develop commercially viable and technically feasible, efficient and reliable power converters for renewable energy, electric transportation and for various industrial applications. This book provides a detailed understanding of the concepts, designs, controls, and application demonstrations of the impedance source converters/inverters. Key features: Comprehensive analysis of the impedance source converter/inverter topologies, including typical topologies and derived topologies. Fully explains the design and control techniques of impedance source converters/inverters, including hardware design and control parameter design for corresponding control methods. Presents the latest power conversion solutions that aim to advance the role of pow...

  5. Impedance Source Power Electronic Converters

    DEFF Research Database (Denmark)

    Liu, Yushan; Abu-Rub, Haitham; Ge, Baoming

    Impedance Source Power Electronic Converters brings together state of the art knowledge and cutting edge techniques in various stages of research related to the ever more popular impedance source converters/inverters. Significant research efforts are underway to develop commercially viable...... and technically feasible, efficient and reliable power converters for renewable energy, electric transportation and for various industrial applications. This book provides a detailed understanding of the concepts, designs, controls, and application demonstrations of the impedance source converters/inverters. Key...... features: Comprehensive analysis of the impedance source converter/inverter topologies, including typical topologies and derived topologies. Fully explains the design and control techniques of impedance source converters/inverters, including hardware design and control parameter design for corresponding...

  6. Noise exposure in convertible automobiles.

    Science.gov (United States)

    Mikulec, A A; Lukens, S B; Jackson, L E; Deyoung, M N

    2011-02-01

    To quantify the noise exposure received while driving a convertible automobile with the top open, compared with the top closed. Five different convertible automobiles were driven, with the top both closed and open, and noise levels measured. The cars were tested at speeds of 88.5, 104.6 and 120.7 km/h. When driving with the convertible top open, the mean noise exposure ranged from 85.3 dB at 88.5 km/h to 89.9 dB at 120.7 km/h. At the tested speeds, noise exposure increased by an average of 12.4-14.6 dB after opening the convertible top. Driving convertible automobiles at speeds exceeding 88.5 km/h, with the top open, may result in noise exposure levels exceeding recommended limits, especially when driving with the convertible top open for prolonged periods.

  7. Advanced converter reactors

    International Nuclear Information System (INIS)

    Kasten, P.R.

    1979-01-01

    Advanced converter reactors (ACRs) of primary US interest are those which can be commercialized within about 20 years, and are: Advanced Light-Water Reactors, Spectral-Shift-Control Reactors, Heavy-Water Reactors (CANDU type), and High-Temperature Gas-Cooled Reactors. These reactors can operate on uranium, thorium, or uranium-thorium fuel cycles, but have the greatest fuel utilization on thorium type cycles. The water reactors tend to operate more economically on uranium cycles, while the HTGR is more economical on thorium cycles. Thus, the HTGR had the greatest practical potential for improving fuel utilization. If the US has 3.4 to 4 million tons U 3 O 8 at reasonable costs, ACRs can make important contributions to maintaining a high nuclear power level for many decades; further, they work well with fast breeder reactors in the long term under symbiotic fueling conditions. Primary nuclear data needs of ACRs are integral measurements of reactivity coefficients and resonance absorption integrals

  8. Catalytic converters in the fireplace

    International Nuclear Information System (INIS)

    Kouki, J.

    1995-01-01

    In addition to selecting the appropriate means of heating and using dry fuel, the amount of harmful emissions contained by flue gases produced by fireplaces can be reduced by technical means. One such option is to use an oxidising catalytic converter. Tests at TTS Institute's Heating Studies Experimental Station have focused on two such converters (dense and coarse) mounted in light-weight iron heating stoves. The ability of the dense catalytic converter to oxidise carbon monoxide gases proved to be good. The concentration of carbon monoxide in the flue gases was reduced by as much as 90 %. Measurements conducted by VTT (Technical Research Centre of Finland) showed that the conversion of other gases, e.g. of methane, was good. The exhaust resistance caused by the dense converter was so great as to necessitate the mounting of a fluegas evacuation fan in the chimney for the purpose of creating sufficient draught. When relying on natural draught, the dense converter requires a chimney of at least 7 metres and a by-pass connection while the fire is being lit. In addition, the converter will have to be constructed to be less dense and this will mean that it's capability to oxidise non-combusted gases will be reduced. The coarse converter did not impair the draught but it's oxidising property was insufficient. With the tests over, the converter was not observed to have become blocked up by impurities

  9. Implementation of a Quadrature Mirror Filter Bank on an SRC Reconfigurable Computer for Real-Time Signal Processing

    National Research Council Canada - National Science Library

    Stoffell, Kevin M

    2006-01-01

    .... The physical connections and signaling specifications for connecting an Analog to Digital converter to a Reconfigurable Computer system manufactured by SRC Computers Incorporated are discussed...

  10. Advanced DC/DC converters

    CERN Document Server

    Luo, Fang Lin

    2003-01-01

    DC/DC conversion techniques have undergone rapid development in recent decades. With the pioneering work of these authors, DC/DC converters have now moved into their sixth generation. This book offers a concise, practical presentation of DC/DC converters, summarizing the spectrum of conversion tecnologies and presentingmany new ideas and more than 100 new topologies. Nowhere else in the literature are DC/DC converters so logically sorted and systematically introduced, and nowhere else can readers find detailed information on prototype topologies that represent a major contribution to modern power engineering. More than 320 figures, 60 tables, and 500 formulae facilitate understand and provide precise data.

  11. Wind/water energy converter

    Science.gov (United States)

    Paulkovich, J.

    1979-01-01

    Device will convert wind, water, tidal or wave energy into electrical or mechanical energy. Is comprised of windmill-like paddles or blades synchronously geared to orient themselves to wind direction for optimum energy extraction.

  12. Matrix Converter in Hybrid Drives

    Czech Academy of Sciences Publication Activity Database

    Lettl, Jiří; Flígl, S.

    -, č. 3 (2004), s. 77-80 ISSN 0204-3599 Institutional research plan: CEZ:AV0Z2057903 Keywords : matrix converter * hybrid drive * electric power splitting Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering

  13. Boron nitride converted carbon fiber

    Science.gov (United States)

    Rousseas, Michael; Mickelson, William; Zettl, Alexander K.

    2016-04-05

    This disclosure provides systems, methods, and apparatus related to boron nitride converted carbon fiber. In one aspect, a method may include the operations of providing boron oxide and carbon fiber, heating the boron oxide to melt the boron oxide and heating the carbon fiber, mixing a nitrogen-containing gas with boron oxide vapor from molten boron oxide, and converting at least a portion of the carbon fiber to boron nitride.

  14. Current status of converter steelmaking

    Energy Technology Data Exchange (ETDEWEB)

    Oghbasialasie, H.; Holappa, L.

    1995-12-31

    This literature work is mainly focusing on the mechanisms of modern converter steelmaking and related with the evaluation of converter technology applied during the last decades and further to the future. The history of steelmaking has been briefly reviewed from bloomeries and early-steelmaking processes to the progress of modern converter process. The pneumatic converter processes were developed in the 1850`s and thereafter the basis for the rapid growth of steel industries was established for the next 100 years. The world production of steel has not continuously grown but fluctuating quite much. It reached 723 Mt in 1994. The production is believed to grow the forecast for the year 2003 being approximately 800 Mt. Electric arc furnace production is estimated to reach 280 Mt by 2003, and BOFIOH will reach 520 Mt by 2003. The current status of the converter steelmaking process is briefly described both on its theoretical bases and practical technological progresses. Developments which significantly improve the process are briefly discussed. Several more recent developments such as combined oxygen blowing process, increased scrap melting, post combustion and hot metal pretreatment are discussed. The future progress will be in further development of these process characteristics as well as in eventual emerging of the continuous converter process. (author)

  15. Converter Monitoring Unit for Retrofit of Wind Power Converters

    DEFF Research Database (Denmark)

    Rannestad, Bjorn; Maarbjerg, Anders Eggert; Frederiksen, Kristian

    2018-01-01

    A Converter Monitoring Unit (CMU), which will enable condition monitoring of wind turbine converters is presented in this paper. Reducing the cost of corrective maintenance by means of condition monitoring is a way of lowering Operation & Maintenance (O&M) costs for wind turbine systems....... The CMU must be able to detect a broad range of failure modes related to Insulated Gate Bipolar Transistor (IGBT) power modules and associated gate drives. IGBT collector-emitter on-state voltage (vceon) and current (ic) is sampled in the CMU and used for detection of emerging failures. A new method...

  16. Modeling of asymmetrical boost converters

    Directory of Open Access Journals (Sweden)

    Eliana Isabel Arango Zuluaga

    2014-01-01

    Full Text Available The asymmetrical interleaved dual boost (AIDB is a fifth-order DC/DC converter designed to interface photovoltaic (PV panels. The AIDB produces small current harmonics to the PV panels, reducing the power losses caused by the converter operation. Moreover, the AIDB provides a large voltage conversion ratio, which is required to step-up the PV voltage to the large dc-link voltage used in grid-connected inverters. To reject irradiance and load disturbances, the AIDB must be operated in a closed-loop and a dynamic model is required. Given that the AIDB converter operates in Discontinuous Conduction Mode (DCM, classical modeling approaches based on Continuous Conduction Mode (CCM are not valid. Moreover, classical DCM modeling techniques are not suitable for the AIDB converter. Therefore, this paper develops a novel mathematical model for the AIDB converter, which is suitable for control-pur-poses. The proposed model is based on the calculation of a diode current that is typically disregarded. Moreover, because the traditional correction to the second duty cycle reported in literature is not effective, a new equation is designed. The model accuracy is contrasted with circuital simulations in time and frequency domains, obtaining satisfactory results. Finally, the usefulness of the model in control applications is illustrated with an application example.

  17. AC-DC PFC Converter Using Combination of Flyback Converter and Full-bridge DC-DC Converter

    Directory of Open Access Journals (Sweden)

    Moh. Zaenal Efendi

    2014-06-01

    Full Text Available This paper presents a combination of power factor correction converter using Flyback converter and Full-bridge dc-dc converter in series connection. Flyback converter is operated in discontinuous conduction mode so that it can serve as a power factor correction converter and meanwhile Full-bridge dc-dc converter is used for dc regulator. This converter system is designed to produce a 86 Volt of output voltage and 2 A of output current. Both simulation and experiment results show that the power factor of this converter achieves up to 0.99 and meets harmonic standard of IEC61000-3-2. Keywords: Flyback Converter, Full-bridge DC-DC Converter, Power Factor Correction.

  18. Charge-pump voltage converter

    Science.gov (United States)

    Brainard, John P [Albuquerque, NM; Christenson, Todd R [Albuquerque, NM

    2009-11-03

    A charge-pump voltage converter for converting a low voltage provided by a low-voltage source to a higher voltage. Charge is inductively generated on a transfer rotor electrode during its transit past an inductor stator electrode and subsequently transferred by the rotating rotor to a collector stator electrode for storage or use. Repetition of the charge transfer process leads to a build-up of voltage on a charge-receiving device. Connection of multiple charge-pump voltage converters in series can generate higher voltages, and connection of multiple charge-pump voltage converters in parallel can generate higher currents. Microelectromechanical (MEMS) embodiments of this invention provide a small and compact high-voltage (several hundred V) voltage source starting with a few-V initial voltage source. The microscale size of many embodiments of this invention make it ideally suited for MEMS- and other micro-applications where integration of the voltage or charge source in a small package is highly desirable.

  19. Reliability of Wave Energy Converters

    DEFF Research Database (Denmark)

    Ambühl, Simon

    There are many different working principles for wave energy converters (WECs) which are used to produce electricity from waves. In order for WECs tobecome successful and more competitive to other renewable electricity sources,the consideration of the structural reliability of WECs is essential.St...

  20. Advanced Thermionic Converter Technology Program

    Science.gov (United States)

    Luke, James R.

    2003-01-01

    A thermionic energy converter (TEC) is a direct energy conversion device, which converts heat to electricity with no moving parts. Thermionic converters are well suited to space nuclear power systems because of their high power density, high heat rejection temperature, and immunity to radiation. Several recent advances in thermionic energy conversion technology have greatly improved the efficiency of these devices. A research program was undertaken to independently confirm these advances, and to extend them to converters with practical geometry. The recent development of a stable cesium/oxygen vapor source has led to a significant improvement in performance. The addition of a small amount of oxygen to the cesium vapor can increase the emission current by a factor of three or more. The beneficial effects of oxygen are stable and reproducible. A TEC with a cold seal has been invented, which greatly simplifies construction, operation, and maintenance of the TEC. Electron reflection from the collector has been shown to reduce the performance of TEC's. Reflection suppressing materials were produced and tested. One sample showed evidence of reflection suppression, increasing the average output voltage by 0.16 V. Another sample did not. Research in this area is ongoing.

  1. Parametric study of laser photovoltaic energy converters

    Science.gov (United States)

    Walker, G. H.; Heinbockel, J. H.

    1987-01-01

    Photovoltaic converters are of interest for converting laser power to electrical power in a space-based laser power system. This paper describes a model for photovoltaic laser converters and the application of this model to a neodymium laser silicon photovoltaic converter system. A parametric study which defines the sensitivity of the photovoltaic parameters is described. An optimized silicon photovoltaic converter has an efficiency greater than 50 percent for 1000 W/sq cm of neodymium laser radiation.

  2. 76 FR 29609 - Wassenaar Arrangement 2010 Plenary Agreements Implementation: Commerce Control List, Definitions...

    Science.gov (United States)

    2011-05-20

    ... Arrangement advocates implementation of effective export controls on strategic items with the objective of....a.2. Adding the word ``Converter'' to ``Analog-to-Digital,'' adding capitalization, and adding the acronyms (ADC) and (DAC) to paragraph 3A001.a.5. Replacing ``Analog-to-digital converters'' with ``ADCs...

  3. Photoelectric converter; Koden henkan soshi

    Energy Technology Data Exchange (ETDEWEB)

    Sawayama, I.

    1995-04-07

    The conventional solar cell module wherein plural photovoltaic elements formed on a metal substrate are connected and coated by weatherproof and translucent resin has defects such as pinholes, and separation because moisture infiltrating from the outside causes dissolution of such conductive matrix as silver in the collecting electrode. This invention relates to a photoelectric converter which has little decrease in the output under the environment of light irradiation, wherein a photoelectric converting semiconductor, a transparent conductive layer on the above-mentioned semiconductor, and conductive member containing water repellent fine powder grains on this transparent conductive layer are laminated successively. Polytetrafluoroethylene, polydimethyl siloxane, polyethylene, and nylon are desirable to be employed as the water repellent fine powder grains. The fine powder grains are mixed with conductive filler and binder to produce conductive paste, pattern-applied by a screen printing machine, and subjected to thermal treatment to form a conductive member. 3 figs., 1 tab.

  4. Photoelectric converters with quantum coherence

    Science.gov (United States)

    Su, Shan-He; Sun, Chang-Pu; Li, Sheng-Wen; Chen, Jin-Can

    2016-05-01

    Photon impingement is capable of liberating electrons in electronic devices and driving the electron flux from the lower chemical potential to higher chemical potential. Previous studies hinted that the thermodynamic efficiency of a nanosized photoelectric converter at maximum power is bounded by the Curzon-Ahlborn efficiency ηCA. In this study, we apply quantum effects to design a photoelectric converter based on a three-level quantum dot (QD) interacting with fermionic baths and photons. We show that, by adopting a pair of suitable degenerate states, quantum coherences induced by the couplings of QDs to sunlight and fermion baths can coexist steadily in nanoelectronic systems. Our analysis indicates that the efficiency at maximum power is no longer limited to ηCA through manipulation of carefully controlled quantum coherences.

  5. Radiated EMI from power converters

    Directory of Open Access Journals (Sweden)

    Arnautovski-Toševa Vesna

    2005-01-01

    Full Text Available With the continuous increase of switching frequency together with the ongoing trend to higher complexity and functionality, power converters as a part of electronic systems have raised more and more electromagnetic energy pollution to the local system environment. In the same time, stringent demands are imposed on the designers of new circuits that electromagnetic interference (EMI has to be suppressed at its source before it is allowed to propagate into other circuits and systems. In this paper, the authors present a full-wave numerical method for calculation and simulation of electromagnetic field radiated by power converter circuitry. The main objective is to analyze the layout geometry in order to obtain competitive PCB layout that will enable suitably attenuated level of the radiated electric field to safe level. By this it would be possible to ensure reliable operation of the sensitive electronic components in the proximity.

  6. Biomass compounds converted to gasoline

    Energy Technology Data Exchange (ETDEWEB)

    1979-10-08

    It is claimed that corn, castor, and jojoba oils as well as Hevea latex can be converted in high yields to gasoline by passage over zeolite catalysts at 450 degrees to 500 degrees centigrade. Gasoline yields are 60% from corn oil (essentially tristearin), compared with 50% yields from methanol. Latex depolymerizes before conversion. Fat and oil molecules adopt conformations that enable them to enter zeolite interstices, resulting in high yields of C6 to C9 aromatics.

  7. Status of advanced bremsstrahlung converters

    International Nuclear Information System (INIS)

    Halbleib, J.A.

    1980-01-01

    This paper is an attempt to review the somewhat ill-defined area of advanced converter research in a more or less chronological fashion. Section 2 reviews the early B/sub z/ work that was motivated by the CASINO project. More recent work makes liberal use of technology from ICF research using REBs is discussed in Sec. 3. Section 4 discusses possible directions for future research, some of which are being actively pursued at Sandia National Laboratories (SNL) and elsewhere

  8. Computerized simulation of converter process

    Energy Technology Data Exchange (ETDEWEB)

    Jalkanen, H.; Suomi, M.L.; Wallgren, M. [Helsinki Univ. of Technology, Otaniemi (Finland). Lab. of Metallurgy

    1996-12-31

    Converter process is essentially an oxidising refining process aiming in addition to (1) the primary refining action, decarburisation of high carbon iron melt, also to (2) maximal elimination of impurity elements, especially silicon, phosphorus and sulphur, (3) melting of substantial amounts of scrap using the extra heat released in oxidation reactions and (4) to exact final steel temperature control, optimal for further treatments. `Quantitative modelling of such a complex non-stationary chemical process as oxygen converting necessitates extensive formulation of chemical and thermal evolution of the process in connection with the technological properties of the reactor and the process control measures. A comprehensive converter simulation program like CONSIM-3. 1 and its preceding versions that is based on the theoretical and practical knowledge on the process can be used for (1) educating specialists and smelter personnel, (2) planning of the blowing programs, (3) developing and testing of process control systems and after some elaboration and restructuring (4) it can be integrated to static or dynamic process control systems. (orig.) SULA 2 Research Programme; 10 refs.

  9. Development of a Compact Matrix Converter

    Directory of Open Access Journals (Sweden)

    J. Bauer

    2009-01-01

    Full Text Available This paper deals with the development of a matrix converter. Matrix converters belong to the category of direct frequency converters. A converter does not contain DC-link and the output voltage is provided by direct switching of voltage from the input phases. This is enabled by 9 bidirectional switches, which are provided by anti-serial connection of 18 IGBT transistors. The absence of a DC-link is great advantage of the matrix converter, but it also increases the requirements on the converter control. For this reason a new prototype of a matrix converter is being developed with sophisticated modern components (FPGA, Power PC equipped in the control part of the converter. The converter will be used for testing new control algorithms and commutation methods. 

  10. Simulation Results of Double Forward Converter

    Directory of Open Access Journals (Sweden)

    P. Vijaya KUMAR

    2009-12-01

    Full Text Available This work aims to find a better forward converter for DC to DC conversion.Simulation of double forward converter in SMPS system is discussed in this paper. Aforward converter with RCD snubber to synchronous rectifier and/or to current doubleris also discussed. The evolution of the forward converter is first reviewed in a tutorialfashion. Performance parameters are discussed including operating principle, voltageconversion ratio, efficiency, device stress, small-signal dynamics, noise and EMI. Itscircuit operation and its performance characteristics of the forward converter with RCDsnubber and double forward converter are described and the simulation results arepresented.

  11. Auxiliary resonant DC tank converter

    Science.gov (United States)

    Peng, Fang Z.

    2000-01-01

    An auxiliary resonant dc tank (ARDCT) converter is provided for achieving soft-switching in a power converter. An ARDCT circuit is coupled directly across a dc bus to the inverter to generate a resonant dc bus voltage, including upper and lower resonant capacitors connected in series as a resonant leg, first and second dc tank capacitors connected in series as a tank leg, and an auxiliary resonant circuit comprising a series combination of a resonant inductor and a pair of auxiliary switching devices. The ARDCT circuit further includes first clamping means for holding the resonant dc bus voltage to the dc tank voltage of the tank leg, and second clamping means for clamping the resonant dc bus voltage to zero during a resonant period. The ARDCT circuit resonantly brings the dc bus voltage to zero in order to provide a zero-voltage switching opportunity for the inverter, then quickly rebounds the dc bus voltage back to the dc tank voltage after the inverter changes state. The auxiliary switching devices are turned on and off under zero-current conditions. The ARDCT circuit only absorbs ripples of the inverter dc bus current, thus having less current stress. In addition, since the ARDCT circuit is coupled in parallel with the dc power supply and the inverter for merely assisting soft-switching of the inverter without participating in real dc power transmission and power conversion, malfunction and failure of the tank circuit will not affect the functional operation of the inverter; thus a highly reliable converter system is expected.

  12. Converting pest insects into food

    DEFF Research Database (Denmark)

    Offenberg, Hans Joachim; Wiwatwittaya, Decha

    2010-01-01

    Canopy dwelling weaver ants (Oecophylla spp.) are used to control a variety of pests in a number of tropical tree crops. What is less familiar is the existence of commercial markets where these ants and their brood are sold for (i) human consumption, (ii) pet food or (iii) traditional medicine...... by pest insects, problematic pests are converted into food and additional earnings. To assess the profitability of providing additional food for the ants, O. smaragdina food conversion efficiency (ECI) was estimated in the laboratory. This estimate suggests the feeding of weaver ants in ant farms...

  13. Power Converters and Power Quality

    CERN Document Server

    Kahle, K

    2015-01-01

    This paper discusses the subject of power quality for power converters. The first part gives an overview of most of the common disturbances and power quality issues in electrical networks for particle accelerators, and explains their consequences for accelerator operation. The propagation of asymmetrical network disturbances into a network is analysed. Quantitative parameters for network disturbances in a typical network are presented, and immunity levels for users’ electrical equipment are proposed. The second part of this paper discusses the technologies and strategies used in particle accelerator networks for power quality improvement . Particular focus is given to networks supplying loads with cycling active and reactive power

  14. High-Performance Data Converters

    DEFF Research Database (Denmark)

    Steensgaard-Madsen, Jesper

    Novel techniques for multi-bit oversampled data conversion are described. State-of-the-art oversampled data converters are analyzed, leading to the conclusion that their performance is limited mainly by low-resolution signal representation. To increase the resolution, high-performance, high......, because that requires a high-resolution loop quantizer which introduces only a small delay. Generally, it is not acceptable to design the loop quantizer as a high-resolution flash quantizer because they require a large chip area and high power consumption. Pipeline techniques are proposed to circumvent...

  15. Power electronics converters and regulators

    CERN Document Server

    Dokić, Branko L

    2015-01-01

    This book is the result of the extensive experience the authors gained through their year-long occupation at the Faculty of Electrical Engineering at the University of Banja Luka. Starting at the fundamental basics of electrical engineering, the book guides the reader into this field and covers all the relevant types of converters and regulators. Understanding is enhanced by the given examples, exercises and solutions. Thus this book can be used as a textbook for students, for self-study or as a reference book for professionals.

  16. Electromechanical converters for electric vehicles

    Science.gov (United States)

    Ambros, T.; Burduniuc, M.; Deaconu, S. I.; Rujanschi, N.

    2018-01-01

    The paper presents the analysis of various constructive schemes of synchronous electromechanical converters with permanent magnets fixed on the rotor and asynchronous with the short-circuit rotor. Various electrical stator winding schemes have also been compared, demonstrating the efficiency of copper utilization in toroidal windings. The electromagnetic calculus of the axial machine has particularities compared to the cylindrical machine, in the paper is presented the method of correlating the geometry of the cylindrical and axial machines. In this case the method and recommendations used in the design of such machines may be used.

  17. Power electronic converters without electrolytic capacitors

    OpenAIRE

    Van den Bossche, Alex; Haddad, Salim; Mordjaoui, Mourad

    2017-01-01

    Power electronic converters may have a quite long lifetime, but some applications such as converters for automotive and photovoltaic could even desire a longer life. One of the elements to increase the lifetime of converters is to avoid electrolytic capacitors, They can be replaced by metalized film capacitors or ceramic capacitors. A lot of converter types can be re-designed to use them, but it influences the way of designing, as a lower capacitance value is used. Electrolytic capacitors are...

  18. OAM mode converter in twisted fibers

    DEFF Research Database (Denmark)

    Usuga Castaneda, Mario A.; Beltran-Mejia, Felipe; Cordeiro, Cristiano

    2014-01-01

    We analyze the case of an OAM mode converter based on a twisted fiber, through finite element simulations where we exploit an equivalence between geometric and material transformations. The obtained converter has potential applications in MDM. © 2014 OSA.......We analyze the case of an OAM mode converter based on a twisted fiber, through finite element simulations where we exploit an equivalence between geometric and material transformations. The obtained converter has potential applications in MDM. © 2014 OSA....

  19. Hybrid thermionic-photovoltaic converter

    Energy Technology Data Exchange (ETDEWEB)

    Datas, A. [Instituto de Energía Solar, Universidad Politécnica de Madrid, 28040 Madrid (Spain)

    2016-04-04

    A conceptual device for the direct conversion of heat into electricity is presented. This concept hybridizes thermionic (TI) and thermophotovoltaic (TPV) energy conversion in a single thermionic-photovoltaic (TIPV) solid-state device. This device transforms into electricity both the electron and photon fluxes emitted by an incandescent surface. This letter presents an idealized analysis of this device in order to determine its theoretical potential. According to this analysis, the key advantage of this converter, with respect to either TPV or TI, is the higher power density in an extended temperature range. For low temperatures, TIPV performs like TPV due to the negligible electron flux. On the contrary, for high temperatures, TIPV performs like TI due to the great enhancement of the electron flux, which overshadows the photon flux contribution. At the intermediate temperatures, ∼1650 K in the case of this particular study, I show that the power density potential of TIPV converter is twice as great as that of TPV and TI. The greatest impact concerns applications in which the temperature varies in a relatively wide range, for which averaged power density enhancement above 500% is attainable.

  20. Manufacturing method of photoelectric converter

    Energy Technology Data Exchange (ETDEWEB)

    Toda, Koji; Niwa, Yasuo

    1987-06-24

    In a method of making a thin film for a photoelectric converter by a method to form an electroconductive layer by burning a mixture of lead oxide and chromic oxide, thickness of the film was limited and the poreless uniform film was not obtainable. The intransparency of the film gave low conversion efficiency only. This invention enabled to obtain a transparent film wherein an oxide (containing lead and chrome) is used as a target to form, in vacuum, a thin film of the oxide, and then this thin film is heat-treated in an atmosphere at least containing lead. Thin transparent film was obtained enhancing the conversion efficiency. High quality and high reliability are ensured because a poreless uniform film can be obtained. Cost was reduced because mass-production was made possible by the use of a vacuum technique. (5 figs)

  1. Efficiency of Capacitively Loaded Converters

    DEFF Research Database (Denmark)

    Andersen, Thomas; Huang, Lina; Andersen, Michael A. E.

    2012-01-01

    is introduced as a definition of efficiency. The calculated and measured efficiency curves for charging DEAP actuator, polypropylene film capacitor and X7R MLCC are provided and compared. The attention has to be paid for the voltage dependent capacitive load, like X7R MLCC, when evaluating the charging......This paper explores the characteristic of capacitance versus voltage for dielectric electro active polymer (DEAP) actuator, 2kV polypropylene film capacitor as well as 3kV X7R multi layer ceramic capacitor (MLCC) at the beginning. An energy efficiency for capacitively loaded converters...... polypropylene film capacitor can be the equivalent capacitive load. Because of the voltage dependent characteristic, X7R MLCC cannot be used to replace the DEAP actuator. However, this type of capacitor can be used to substitute the capacitive actuator with voltage dependent property at the development phase....

  2. Three-phase AC-AC power converters based on matrix converter topology matrix-reactance frequency converters concept

    CERN Document Server

    Szczesniak, Pawel

    2013-01-01

    AC voltage frequency changes is one of the most important functions of solid state power converters. The most desirable features in frequency converters are the ability to generate load voltages with arbitrary amplitude and frequency, sinusoidal currents and voltages waveforms; the possibility of providing unity power factor for any load; and, finally, a simple and compact power circuit. Over the past decades, a number of different frequency converter topologies have appeared in the literature, but only the converters with either a voltage or current DC link are commonly used in industrial app

  3. Radiation-Tolerant DC-DC Converters

    Science.gov (United States)

    Skutt, Glenn; Sable, Dan; Leslie, Leonard; Graham, Shawn

    2012-01-01

    A document discusses power converters suitable for space use that meet the DSCC MIL-PRF-38534 Appendix G radiation hardness level P classification. A method for qualifying commercially produced electronic parts for DC-DC converters per the Defense Supply Center Columbus (DSCC) radiation hardened assurance requirements was developed. Development and compliance testing of standard hybrid converters suitable for space use were completed for missions with total dose radiation requirements of up to 30 kRad. This innovation provides the same overall performance as standard hybrid converters, but includes assurance of radiation- tolerant design through components and design compliance testing. This availability of design-certified radiation-tolerant converters can significantly reduce total cost and delivery time for power converters for space applications that fit the appropriate DSCC classification (30 kRad).

  4. Reliability of Power Electronic Converter Systems

    DEFF Research Database (Denmark)

    electronic converter systems; anomaly detection and remaining-life prediction for power electronics; reliability of DC-link capacitors in power electronic converters; reliability of power electronics packaging; modeling for life-time prediction of power semiconductor modules; minimization of DC......-tolerant adjustable speed drive systems; mission profile oriented reliability design in wind turbine and photovoltaic systems; reliability of power conversion systems in photovoltaic applications; power supplies for computers; and high-power converters. Reliability of Power Electronic Converter Systems is essential......The main aims of power electronic converter systems (PECS) are to control, convert, and condition electrical power flow from one form to another through the use of solid-state electronics. This book outlines current research into the scientific modeling, experimentation, and remedial measures...

  5. Gadolinium sheet converter for neutron radiography

    Energy Technology Data Exchange (ETDEWEB)

    Lima, C.T.S. [Laboratorio de Neutrongrafia em Tempo Real (LNRTR/PEN/COPPE), Universidade Federal do Rio de Janeiro, Ilha do Fundao, Caixa Postal 68509, 21941-972 Rio de Janeiro, RJ (Brazil); Crispim, V.R. [Laboratorio de Neutrongrafia em Tempo Real (LNRTR/PEN/COPPE), Universidade Federal do Rio de Janeiro, Ilha do Fundao, Caixa Postal 68509, 21941-972 Rio de Janeiro, RJ (Brazil); PEN/COPPE-DNC/Escola Politecnica CT, Universidade Federal do Rio de Janeiro, Ilha do Fundao, Caixa Postal 68509, 21941-972 Rio de Janeiro, RJ (Brazil)], E-mail: verginia@con.ufrj.br; Santos, W.M.S. [Laboratorio de Colisao Atomica e Molecular (LACAM/IF), Universidade Federal do Rio de Janeiro, Ilha do Fundao, Caixa Postal 68528, 21941-972 Rio de Janeiro, RJ (Brazil)

    2007-12-15

    This work describes a methodology developed for the confection of gadolinium sheet converter for neutron radiography using the gadolinium chloride (GdCl{sub 3}) as material converter. Though manufactured at a relatively low cost, they are as good as the sheet converter on the market. Here, we present neutron radiography of the penetrameter, the edge spread function, the modulation transfer function and characteristic curves for each set sheet-AA400 Kodak film.

  6. Ocean floor mounting of wave energy converters

    Science.gov (United States)

    Siegel, Stefan G

    2015-01-20

    A system for mounting a set of wave energy converters in the ocean includes a pole attached to a floor of an ocean and a slider mounted on the pole in a manner that permits the slider to move vertically along the pole and rotate about the pole. The wave energy converters can then be mounted on the slider to allow adjustment of the depth and orientation of the wave energy converters.

  7. Commutation Processes in Multiresonant ZVS Bridge Converter

    Directory of Open Access Journals (Sweden)

    Miroslaw Luft

    2008-01-01

    Full Text Available The analysis of the multiresonant ZVS DC/DC bridge converter is presented. The control system of the converter is basedon the method of frequency control at the constant time of transistor turn-off with a phase shift. The operation of the circuit is givenand the operating range of the converter is defined where ZVS switching operation is assured. Control characteristics are given andthe converter’s efficiency is defined. The circuit’s operation is analysed on the basis of results of the converter simulation tests using Simplorer programme.

  8. Present trends in HVDC converter station design

    Energy Technology Data Exchange (ETDEWEB)

    Carlsson, Lennart; Asplund, Gunnar; Bjorklund, Hans; Flisberg, Gunnar [ABB Power Systems AB, Ludvika (Sweden)

    1994-12-31

    HVDC converter station technology has developed rapidly to satisfy increasing requirements during past 10 - 15 years, but there has not been any dramatic changes since thyristor valves were introduced in the mid 70s. This paper describes some recent and expected future developments, that will substantiality change and simplify future converter stations. (author) 4 refs., 7 figs.

  9. Modelling and Control of Grid converter

    DEFF Research Database (Denmark)

    Teodorescu, Remus; Blaabjerg, Frede; Iov, Florin

    The present report describes the work done in the Phase 1a during the research project "Modelling and Control of Grid Converter". The developed models for the plant and different control strategies for the grid converter are presented in detail. Simulation results under different operating...

  10. Controller for a wave energy converter

    Science.gov (United States)

    Wilson, David G.; Bull, Diana L.; Robinett, III, Rush D.

    2015-09-22

    A wave energy converter (WEC) is described, the WEC including a power take off (PTO) that converts relative motion of bodies of the WEC into electrical energy. A controller controls operation of the PTO, causing the PTO to act as a motor to widen a wave frequency spectrum that is usable to generate electrical energy.

  11. Utilization of Nonlinear Converters for Audio Amplification

    DEFF Research Database (Denmark)

    Iversen, Niels; Birch, Thomas; Knott, Arnold

    2012-01-01

    . The introduction of non-linear converters for audio amplication defeats this limitation. A Cuk converter, designed to deliver an AC peak output voltage twice the supply voltage, is presented in this paper. A 3V prototype has been developed to prove the concept. The prototype shows that it is possible to achieve...

  12. Front converter lenses for smart phones

    Science.gov (United States)

    Reiley, Daniel J.; O'Neil, Patrick

    2017-11-01

    Front converters for the iPhone 6, from six different vendors, are examined in detail. Telephoto, wide angle, and fisheye converters are examined. System performance is measured, and the measured lens designs are presented. Great variety is found in both design type and performance; little correlation is found between performance and design type.

  13. Switched-mode converters (one quadrant)

    CERN Document Server

    Barrade, P

    2006-01-01

    Switched-mode converters are DC/DC converters that supply DC loads with a regulated output voltage, and protection against overcurrents and short circuits. These converters are generally fed from an AC network via a transformer and a conventional diode rectifier. Switched-mode converters (one quadrant) are non-reversible converters that allow the feeding of a DC load with unipolar voltage and current. The switched-mode converters presented in this contribution are classified into two families. The first is dedicated to the basic topologies of DC/DC converters, generally used for low- to mid-power applications. As such structures enable only hard commutation processes, the main drawback of such topologies is high commutation losses. A typical multichannel evolution is presented that allows an interesting decrease in these losses. Deduced from this direct DC/DC converter, an evolution is also presented that allows the integration of a transformer into the buck and the buck–boost structure. This enables an int...

  14. Modeling and Simulation of Matrix Converter

    DEFF Research Database (Denmark)

    Liu, Fu-rong; Klumpner, Christian; Blaabjerg, Frede

    2005-01-01

    This paper discusses the modeling and simulation of matrix converter. Two models of matrix converter are presented: one is based on indirect space vector modulation and the other is based on power balance equation. The basis of these two models is• given and the process on modeling is introduced...

  15. A novel converter topology for TEM applications

    Indian Academy of Sciences (India)

    and energy levels of the TEM system, require special type of excitation technique. Power converters for such non-standard requirements are not reported in the literature, particularly for TEM applications. This paper introduces TEM systems to the reader and presents the requirements for excitation. A converter topology.

  16. Multilevel converters for 10 MW Wind Turbines

    DEFF Research Database (Denmark)

    Ma, Ke; Blaabjerg, Frede

    2011-01-01

    Several promising multi-level converter configurations for 10 MW Wind Turbines both with direct drive and one-stage gear box drive using Permanent Magnet Synchronous Generator (PMSG) are proposed, designed and compared. Reliability is a crucial indicator for large scale wind power converters...

  17. A novel converter topology for TEM applications

    Indian Academy of Sciences (India)

    Power converters for such non-standard requirements are not reported in the literature, particularly for TEM applications. This paper introduces TEM systems to the reader and presents the requirements for excitation. A converter topology to meet the requirements, it's analysis, control and performance are presented. Among ...

  18. Periodic Control of Power Electronic Converters

    DEFF Research Database (Denmark)

    Zhou, Keliang; Danwei, Wang; Yang, Yongheng

    Advanced power electronic converters convert, control and condition electricity. Power converters require control strategies for periodic signal compensation to assure good power quality and stable power system operation. This comprehensive text presents the most recent internal model principle...... based periodic control technology, which offers the perfect periodic control solution for power electronic conversion. It also provides complete analysis and synthesis methods for periodic control systems, and plenty of practical examples to demonstrate the validity of proposed periodic control...... technology for power converters. It proposes a unified framework for housing periodic control schemes for power converters, and provides a general proportional-integral-derivative control solution to periodic signal compensation in extensive engineering applications. Periodic Control of Power Electronic...

  19. A review of Indirect Matrix Converter Topologies

    Directory of Open Access Journals (Sweden)

    Salem Rahmani

    2015-08-01

    Full Text Available Abstract—Matrix Converter (MC is a modern direct AC/AC electrical power converter without dc-link capacitor. MC is operated in four quadrant, assuring a control of the output voltage, amplitude and frequency. The matrix converter has recently attracted significant attention among researchers and it has become increasing attractive for applications of wind energy conversion, military power supplies, induction motor drives, etc. Recently, different MC topologies have been proposed and developed which have their own advantages and disadvantages. Matrix converter can be classified as direct and indirect structures. The direct one has been elaborated in previous work. In this paper the indirect MCs are reviewed. Different characteristics of the indirect MC topologies are mentioned to show the strengths and weaknesses of such converter topologies.

  20. Switched Mode Four-Quadrant Converters

    CERN Document Server

    Thurel, Y

    2015-01-01

    This paper was originally presented at CAS-2004, and was slightly modified for CAS-2014. It presents a review of the key parameters that impact the design choices for a true four-quadrant power converter, in the range 1-10 kW, mainly based on switching mode converter topology. This paper will first describe the state-of-the-art for this power converter family, giving the drawbacks and advantages of different possible solutions. It will also present practical results obtained from the CERN-designed converter. It will finally give some important tips regarding critical phases like test one, when conducting a project dealing with this type of power converter.

  1. Qualitative model of a plasma photoelectric converter

    Science.gov (United States)

    Gorbunov, N. A.; Flamant, G.

    2009-01-01

    A converter of focused optical radiation into electric current is considered on the basis of the photovoltaic effect in plasmas. The converter model is based on analysis of asymmetric spatial distributions of charge particle number density and ambipolar potential in the photoplasma produced by external optical radiation focused in a heat pipe filled with a mixture of alkali vapor and a heavy inert gas. Energy balance in the plasma photoelectric converter is analyzed. The conditions in which the external radiation energy is effectively absorbed in the converter are indicated. The plasma parameters for which the energy of absorbed optical radiation is mainly spent on sustaining the ambipolar field in the plasma are determined. It is shown that the plasma photoelectric converter makes it possible to attain a high conversion efficiency for focused solar radiation.

  2. A novel power converter for photovoltaic applications

    Science.gov (United States)

    Yuvarajan, S.; Yu, Dachuan; Xu, Shanguang

    A simple and economical power conditioner to convert the power available from solar panels into 60 Hz ac voltage is described. The raw dc voltage from the solar panels is converted to a regulated dc voltage using a boost converter and a large capacitor and the dc output is then converted to 60 Hz ac using a bridge inverter. The ratio between the load current and the short-circuit current of a PV panel at maximum power point is nearly constant for different insolation (light) levels and this property is utilized in designing a simple maximum power point tracking (MPPT) controller. The controller includes a novel arrangement for sensing the short-circuit current without disturbing the operation of the PV panel and implementing MPPT. The switching losses in the inverter are reduced by using snubbers. The results obtained on an experimental converter are presented.

  3. The Simulation of DFIG Grid Side Converter

    Directory of Open Access Journals (Sweden)

    LU Yan-Ling

    2017-02-01

    Full Text Available Firstly,DFIG basic structure of grid side converter was analyzed according to basic principles of voltage converter, and a mathematical model of grid side converter was established in the three-phase stationary coordinate system and the two-phase rotating coordinate system respectively. Then use the grid voltage oriented vector control strategy based On dq coordinate model of the grid side converter and its essential principles and realization scheme were introduced. Finally,SVPWM,Park,control systems and other power electronics model were built in matlab/simulink,converter was simulated based On vector control strategy under rectifier state and inverter state respectively. The simulation results show that the control strategy has a good dynamic response,and by choosing the appropriate inductance,capacitance,the network side current will reach stable state quickly with smooth waveform and small harmonic,while the DC voltage will reach stable value quickly with small overshoot.

  4. Transformer Isolated Buck-Boost Converters

    Directory of Open Access Journals (Sweden)

    Barry W. Williams

    2016-12-01

    Full Text Available Of the single-switch dc-to-dc converters, those with the buck-boost voltage transfer function offer most potential for transformer coupling, hence isolation, at the kilowatt level. This paper highlights the limitations of the traditional magnetic coupled, buck-boost topology. Then four split-capacitor transformer-coupled topologies (specifically the Cuk, sepic, zeta, and a new, converters with a common ac equivalent circuit are explored, that do not temporarily store core magnetic energy as does the traditional isolated buck-boost converter nor have a core dc magnetizing current bias, as with the sepic and zeta transformer coupled topologies. Core dc bias capacitive voltage compensation is a practical design constraint in three of the four topologies, while all four must cater for stray and leakage inductance effects. Simulations and experimental results for the new converter at 408W support the transformer-coupled, single-switch dc-to-dc converter concepts investigated.

  5. Underwater noise from a wave energy converter

    DEFF Research Database (Denmark)

    Tougaard, Jakob

    of the absorber type. During recordings the converter was operating close to maximum power output (nominal capacity of 110 kW). During operation the independently operating absorbers float semi-submerged in the water and wave-generated up-and-down motion is converted into hydraulic pressure by means of pistons...... connected to the arms of the absorbers. The hydraulic pressure then in turn drives the generator. A 57 minute sequence of noise from the converter was recorded by a Loggerhead datalogger deployed in 7 m deep water 25 m from the converter. This sequence contained recordings of ambient noise, the converter...... in full operation and start and stop of the converter. Median broad band (10 Hz – 20 kHz) sound pressure level (Leq) was 123 dB re. 1 Pa, irrespective of status of the wave energy converter (stopped, running or starting/stopping). The most pronounced peak in the third-octave spectrum was in the 160 Hz...

  6. Electromagnetic Compatibility of Matrix Converter System

    Directory of Open Access Journals (Sweden)

    S. Fligl

    2006-12-01

    Full Text Available The presented paper deals with matrix converters pulse width modulation strategies design with emphasis on the electromagnetic compatibility. Matrix converters provide an all-silicon solution to the problem of converting AC power from one frequency to another, offering almost all the features required of an ideal static frequency changer. They possess many advantages compared to the conventional voltage or current source inverters. A matrix converter does not require energy storage components as a bulky capacitor or an inductance in the DC-link, and enables the bi-directional power flow between the power supply and load. The most of the contemporary modulation strategies are able to provide practically sinusoidal waveforms of the input and output currents with negligible low order harmonics, and to control the input displacement factor. The perspective of matrix converters regarding EMC in comparison with other types of converters is brightly evident because it is no need to use any equipment for power factor correction and current and voltage harmonics reduction. Such converter with proper control is properly compatible both with the supply mains and with the supplied load. A special digital control system was developed for the realized experimental test bed which makes it possible to achieve greater throughput of the digital control system and its variability.

  7. Selective harmonic control for power converters

    DEFF Research Database (Denmark)

    Zhou, Keliang; Yang, Yongheng; Blaabjerg, Frede

    2014-01-01

    This paper proposes an Internal Model Principle (IMP) based Selective Harmonic Controller (SHC) for power converters. The proposed SHC offers an optimal control solution for power converters to mitigate power harmonics. It makes a good trade-off among cost, complexity and performance. It has high...... accuracy and fast transient response, and it is cost-effective, easy for real-time implementation, and compatible for design rules-of-thumb. An application on a three-phase PWM converter has confirmed the effectiveness of the proposed control scheme in terms of harmonic mitigation....

  8. High-power converters and AC drives

    CERN Document Server

    Wu, Bin

    2017-01-01

    This new edition reflects the recent technological advancements in the MV drive industry, such as advanced multilevel converters and drive configurations. It includes three new chapters, Control of Synchronous Motor Drives, Transformerless MV Drives, and Matrix Converter Fed Drives. In addition, there are extensively revised chapters on Multilevel Voltage Source Inverters and Voltage Source Inverter-Fed Drives. This book includes a systematic analysis on a variety of high-power multilevel converters, illustrates important concepts with simulations and experiments, introduces various megawatt drives produced by world leading drive manufacturers, and addresses practical problems and their mitigations methods.

  9. CAS - CERN Accelerator School: Power Converters

    CERN Document Server

    2015-01-01

    These proceedings collate lectures given at the twenty-eighth specialized course organised by the CERN Accelerator School (CAS). The course was held at the Hotel du Parc, Baden, Switzerland from 7 - 14 May 2014, in collaboration with the Paul Scherrer Institute. Following introductory lectures on accelerators and the requirements on power converters, the course covered components and topologies of the different types of power converters needed for particle accelerators. Issues of design, control and exploitation in a sometimes-hostile environment were addressed. Site visits to ABB and PSI provided an insight into state-of-the-art power converter production and operation, while topical seminars completed the programme.

  10. Reliability of Power Electronic Converter Systems

    DEFF Research Database (Denmark)

    for advancing the reliability, availability, system robustness, and maintainability of PECS at different levels of complexity. Drawing on the experience of an international team of experts, this book explores the reliability of PECS covering topics including an introduction to reliability engineering in power......-tolerant adjustable speed drive systems; mission profile oriented reliability design in wind turbine and photovoltaic systems; reliability of power conversion systems in photovoltaic applications; power supplies for computers; and high-power converters. Reliability of Power Electronic Converter Systems is essential...... reading for researchers, professionals and students working with power electronics and their applications, particularly those specializing in the development and application of power electronic converters and systems....

  11. Power Electronics Converters for Wind Turbine Systems

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Liserre, Marco; Ma, Ke

    2012-01-01

    The steady growth of installed wind power together with the upscaling of the single wind turbine power capability has pushed the research and development of power converters toward full-scale power conversion, lowered cost pr kW, increased power density, and also the need for higher reliability......, in the latter case with attention to series connection and parallel connection either electrical or magnetic ones (multiphase/windings machines/transformers). It is concluded that as the power level increases in wind turbines, medium-voltage power converters will be a dominant power converter configuration...

  12. Synchronous Control of Modular Multilevel Converters

    DEFF Research Database (Denmark)

    Oleschuk, Valentin; Blaabjerg, Frede; Bose, Bimal K.

    2002-01-01

    A novel method of direct synchronous pulsewidth modulation (PWM) is applied for control of modular multilevel converters consisting from three standard triphase inverter modules along with an 0.33 p.u. output transformer. The proposed method provides synchronisation of the voltage waveforms...... for each module and the composed voltage at the output of the converter. Multilevel output voltage of the converter has quarter-wave symmetry during the whole range including the zone of overmodulation. Both continuous and discontinuous versions of synchronous PWM, based on vector approach...

  13. State estimation for wave energy converters

    Energy Technology Data Exchange (ETDEWEB)

    Bacelli, Giorgio; Coe, Ryan Geoffrey

    2017-04-01

    This report gives a brief discussion and examples on the topic of state estimation for wave energy converters (WECs). These methods are intended for use to enable real-time closed loop control of WECs.

  14. multilevel buck converter for automotive electrical load

    African Journals Online (AJOL)

    user

    MULTILEVEL BUCK CONVERTER FOR AUTOMOTIVE ELECTRICAL LOAD. E. T. Yabefa1,* and D. Ebregbe2. 1ELECTRICAL DEPARTMENT, BAYELSA STATE COLLEGE OF ARTS & SCIENCE (BYCAS) YENAGOA, BAYELSA STATE NIGERIA. 2ELECTRICAL ENGINEERING DEPARTMENT, NIGER DELTA UNIVERSITY, ...

  15. Reliability of power electronic converter systems

    CERN Document Server

    Chung, Henry Shu-hung; Blaabjerg, Frede; Pecht, Michael

    2016-01-01

    This book outlines current research into the scientific modeling, experimentation, and remedial measures for advancing the reliability, availability, system robustness, and maintainability of Power Electronic Converter Systems (PECS) at different levels of complexity.

  16. A three-port direct current converter

    DEFF Research Database (Denmark)

    2016-01-01

    The three-port direct current converter comprising: at least one input direct current source; at least one storage battery; a primary side circuit; a secondary side circuit; a first single magnetic component shared by the primary side circuit and the secondary side circuit, wherein the primary side...... circuit comprises a connection between the at least one input direct current source and the at least one storage battery, the primary side circuit configured for operating as a buck converter; a second magnetic component serially coupled to the first single magnetic component, wherein the first and second...... magnetic components are configured to perform a voltage step-up, wherein the secondary side circuit comprises a connection between the at least one storage battery and at least one load, the secondary side configured for operating as a tapped boost converter; wherein the three-port direct current converter...

  17. "Forback" Dc-To-Dc Converters

    Science.gov (United States)

    Lukemire, Alan T.

    1992-01-01

    Dc-to-dc power-converter circuits called "forback" resemble circuits of standard configurations called "forward", "flyback", and "Cuk". Circuit employs minor modifications to existing topologies, combines advantages, while eliminating disadvantages, of older circuits.

  18. Multilevel-clamped multilevel converters (MLC2)

    DEFF Research Database (Denmark)

    Rodriguez, Pedro; Bellar, Maria Dias; Muñoz-Aguliar, Raúl Santiago

    2012-01-01

    This letter introduces a new series of multilevel (ML) converters based on the ML clamping concept. By applying this technique, a ML clamping unit (MCU) conveys additional levels for synthesizing the output waveforms of a diode-clampedML dc– ac power converter. The basic building block of the ML...... clamping scheme is the ML clamping cell, which is composed of a pair of dc sources associated with one single-pole/triple-throw type of switch arrangement. The number of series-connected ML-clamping cells will set the number of levels of the synthesized waveform. By depending on the MCU arrangements......, different converter configurations can be derived, namely, the common clamping and the modular types. Both approaches can be accomplished by employing classical three-level neutral-point-clamped (NPC) technology. Thus, the overall structure of the resultant converter is kept simple, wherein the number...

  19. Switching power converters medium and high power

    CERN Document Server

    Neacsu, Dorin O

    2013-01-01

    An examination of all of the multidisciplinary aspects of medium- and high-power converter systems, including basic power electronics, digital control and hardware, sensors, analog preprocessing of signals, protection devices and fault management, and pulse-width-modulation (PWM) algorithms, Switching Power Converters: Medium and High Power, Second Edition discusses the actual use of industrial technology and its related subassemblies and components, covering facets of implementation otherwise overlooked by theoretical textbooks. The updated Second Edition contains many new figures, as well as

  20. A new type time-amplitude converter

    International Nuclear Information System (INIS)

    Mou Haiwei; Han Jian; Li Zhongwei

    2004-01-01

    The time-amplitude converter is used mostly in nuclear physics experiments where require fast time measurement, such as the identify of particles, the measurement of excitated life-span and flying time of nucleon, and so on. According to the requirement of experiment, a new type time-amplitude converter composing of IC has been developed. It is precision is 100 ns. It has the merits of stable performance, higher precision and so on. (authors)

  1. AC – AC Converters for UPS

    Directory of Open Access Journals (Sweden)

    Rusalin Lucian R. Păun

    2008-05-01

    Full Text Available This paper propose a new control technique forsingle – phase AC – AC converters used for a on-line UPSwith a good dynamic response, a reduced-partscomponents, a good output characteristic, a good powerfactorcorrection(PFC. This converter no needs anisolation transformer. A power factor correction rectifierand an inverter with the proposed control scheme has beendesigned and simulated using Caspoc2007, validating theconcept.

  2. Resonant Wave Energy Converters: Concept development

    International Nuclear Information System (INIS)

    Arena, Felice; Barbaro, Giuseppe; Fiamma, Vincenzo; Laface, Valentina; Malara, Giovanni; Romolo, Alessandra; Strati, Federica Mara

    2015-01-01

    The Resonant Wave Energy Converter (REWEC) is a device for converting sea wave energy to electrical energy. It belongs to the family of Oscillating Water Columns and is composed by an absorbing chamber connected to the open sea via a vertical duct. The paper gives a holistic view on the concept development of the device, starting from its implementation in the context of submerged breakwaters to the recently developed vertical breakwaters. [it

  3. LHC Power Converters: A Precision Game

    CERN Multimedia

    2001-01-01

    The LHC test-bed, String 2, is close to commissioning and one important element to get a first chance to prove what it can do is the power converter system. In String 2 there are 16 converters, in the full LHC there will be almost 1800. This article takes a look at what is so special about the power converters for the LHC. The 13 000 Amps power converters with the watercooled cables going to the String 2 feedboxes. The LHC's superconducting magnets will be the pinnacle of high technology. But to work, they'll need the help of high-precision power converters to supply them with extremely stable DC current. Perfection will be the name of the game, with an accuracy of just 1-2 parts per million (ppm) required. LEP, for the sake of comparison, could live with 10-20 ppm. The LHC's power converters will be very different from those of LEP or the SPS since the new accelerator's magnets are mostly superconducting. That means that they require much higher currents at a lower voltage since superconductors have no re...

  4. Isolated and soft-switched power converter

    Science.gov (United States)

    Peng, Fang Zheng; Adams, Donald Joe

    2002-01-01

    An isolated and soft-switched power converter is used for DC/DC and DC/DC/AC power conversion. The power converter includes two resonant tank circuits coupled back-to-back through an isolation transformer. Each resonant tank circuit includes a pair of resonant capacitors connected in series as a resonant leg, a pair of tank capacitors connected in series as a tank leg, and a pair of switching devices with anti-parallel clamping diodes coupled in series as resonant switches and clamping devices for the resonant leg. The power converter is well suited for DC/DC and DC/DC/AC power conversion applications in which high-voltage isolation, DC to DC voltage boost, bidirectional power flow, and a minimal number of conventional switching components are important design objectives. For example, the power converter is especially well suited to electric vehicle applications and load-side electric generation and storage systems, and other applications in which these objectives are important. The power converter may be used for many different applications, including electric vehicles, hybrid combustion/electric vehicles, fuel-cell powered vehicles with low-voltage starting, remote power sources utilizing low-voltage DC power sources, such as photovoltaics and others, electric power backup systems, and load-side electric storage and generation systems.

  5. Underwater noise from a wave energy converter

    DEFF Research Database (Denmark)

    Tougaard, Jakob

    in full operation and start and stop of the converter. Median broad band (10 Hz – 20 kHz) sound pressure level (Leq) was 123 dB re. 1 Pa, irrespective of status of the wave energy converter (stopped, running or starting/stopping). The most pronounced peak in the third-octave spectrum was in the 160 Hz...... band during start and stop of the converter, attributed to the hydraulic pump responsible for lifting and lowering the absorbers. Less pronounced, but still statistically significant differences were seen in the bands 125, 160, 200 and 250 Hz when operation and ambient were compared. No statistically...... significant noise above ambient could be detected above the 250 Hz band. The absolute increase in noise above ambient was very small. L50 third-octave levels in the four bands with the converter running were thus only 1-2 dB above ambient L50 levels. The noise recorded 25 m from the wave energy converter...

  6. High Efficiency Reversible Fuel Cell Power Converter

    DEFF Research Database (Denmark)

    Pittini, Riccardo

    to traditional unidirectional fuel cell, bidirectional fuel cells have increased operating voltage and current ranges. These characteristics increase the stresses on dc-dc and dc-ac converters in the electrical system, which require proper design and advanced optimization. This work is part of the PhD project...... entitled "High Efficiency Reversible Fuel Cell Power Converter" and it presents the design of a high efficiency dc-dc converter developed and optimized for bidirectional fuel cell applications. First, a brief overview of fuel cell and energy storage technologies is presented. Different system topologies......The large scale integration of renewable energy sources requires suitable energy storage systems to balance energy production and demand in the electrical grid. Bidirectional fuel cells are an attractive technology for energy storage systems due to the high energy density of fuel. Compared...

  7. Reliability of Power Electronic Converter Systems

    DEFF Research Database (Denmark)

    The main aims of power electronic converter systems (PECS) are to control, convert, and condition electrical power flow from one form to another through the use of solid-state electronics. This book outlines current research into the scientific modeling, experimentation, and remedial measures......-link capacitance in power electronic converter systems; wind turbine systems; smart control strategies for improved reliability of power electronics system; lifetime modelling; power module lifetime test and state monitoring; tools for performance and reliability analysis of power electronics systems; fault...... for advancing the reliability, availability, system robustness, and maintainability of PECS at different levels of complexity. Drawing on the experience of an international team of experts, this book explores the reliability of PECS covering topics including an introduction to reliability engineering in power...

  8. Converters for Distributed Power Generation Systems

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Yang, Yongheng

    2015-01-01

    Power electronics technology has become the enabling technology for the integration of distributed power generation systems (DPGS) such as offshore wind turbine power systems and commercial photovoltaic power plants. Depending on the applications, a vast array of DPGS-based power converter...... topologies has been developed and more are coming into the market in order to achieve an efficient and reliable power conversion from the renewables. In addition, stringent demands from both the distribution system operators and the consumers have been imposed on the renewable-based DPGS. This article...... presents an overview of the power converters for the DPGS, mainly based on wind turbine systems and photovoltaic systems, covering a wide range of applications. Moreover, the modulation schemes and interfacing power filters for the power converters are also exemplified. Finally, the general control...

  9. Measurements of neutron spectrum from uranium converter

    International Nuclear Information System (INIS)

    Ninkovic, M.; Sotic, O.; Marinkovic, S.

    1978-01-01

    The procedure for determination of energetic distribution of neutrons by the multisphere technique is given. The theoretical basis and features of the method are explained. The spectral distribution of neutrons emerging from the neutron converter constructed at the bare reactor assembly RB, has been determined applying the existing computer programme and literature data for the energetic dependence functions of spheres of various diameters. The obtained spectral distribution has a specific maximum in the domain of fast neutrons, justifying thus the reacton for the construction of the converter. The neutron spectrum data obtained and given in this report are very important for the use of the converter in neutron dosimetry and radiation protection, as well as in the radiobiology, shielding, reactor physics etc. (author)

  10. Radioisotope thermionic converters for space applications

    International Nuclear Information System (INIS)

    Miskolczy, G.; Lieb, D.P.

    1990-01-01

    The recent history of radioisotope thermionics is reviewed, with emphasis on the U.S. programs, and the prospects for the future are assessed. In radioisotope thermionic converters the emitter heat is generated by the decay of a radioactive isotope. The thermionic converter emitter is mounted directly on a capsule containing the isotope. The rest of the capsule is generally insulated to reduce thermal loss. The development of isotope-fueled thermionic power systems for space application has been pursued since the late 1950's. The U.S. effort was concentrated on modular systems with alpha emitters as the isotope heat source. In the SNAP-13 program, the heat sources were Cerium isotopes and each module produced about 100 watts. The converters were planar diodes and the capsule was insulated with multi-foil insulation

  11. Reliability of Power Electronic Converter Systems

    DEFF Research Database (Denmark)

    for advancing the reliability, availability, system robustness, and maintainability of PECS at different levels of complexity. Drawing on the experience of an international team of experts, this book explores the reliability of PECS covering topics including an introduction to reliability engineering in power...... electronic converter systems; anomaly detection and remaining-life prediction for power electronics; reliability of DC-link capacitors in power electronic converters; reliability of power electronics packaging; modeling for life-time prediction of power semiconductor modules; minimization of DC......-link capacitance in power electronic converter systems; wind turbine systems; smart control strategies for improved reliability of power electronics system; lifetime modelling; power module lifetime test and state monitoring; tools for performance and reliability analysis of power electronics systems; fault...

  12. Current Mode Data Converters for Sensor Systems

    DEFF Research Database (Denmark)

    Jørgensen, Ivan Herald Holger

    to reduce these. A novel measure called the 'error energy measure' is presented. This measure is very helpful in the design phase as it evaluates the dynamic performance of a DAC without performing long term simulations. A thorough analysis of the stability of 1-bit oversampled data converters is presented......This thesis is mainly concerned with data conversion. Especially data conversion using current mode signal processing is treated.A tutorial chapter introducing D/A conversion is presented. In this chapter the effects that cause static and dynamic nonlinearities are discussed along with methods....... Also, a methodology for designing the feedback filter in oversampled data converters is presented. Finally, the effect of nonideal effects in oversampled converters is investigated.Switched current (SI) technique is briefly presented at the system level and transistor level. A thorough analysis...

  13. single-phase dc phase dc-ac boost converter ac boost converter

    African Journals Online (AJOL)

    User

    supply (UPS) AC motor drives and other power sup systems, need to step-up the DC input voltage. increase the output voltage level in order requirements, DC-DC boost converter is used provide DC bus voltage for PWM inverters. Hence, conventional design always cascades DC and a separate DC-AC converter.

  14. Efficient modelling of a modular multilevel converter

    DEFF Research Database (Denmark)

    El-Khatib, Walid Ziad; Holbøll, Joachim; Rasmussen, Tonny Wederberg

    2013-01-01

    Looking at the near future, we see that offshore wind penetration into the electrical grid will continue increasing rapidly. Until very recently, the trend has been to place the offshore wind farms close to shore within the reach for transmission using HVAC cables but for larger distances HVDC...... are calculated for the converter. Time-domain simulations on a MMC HVDC test system are performed in the PSCAD/EMTDC software environment based on the new model. The results demonstrate that the modeled MMC-HVDC system with or without converter transformer is able to operate under specific fault conditions....

  15. The Angiotensin-Converting-Enzyme-Induced Angioedema.

    Science.gov (United States)

    Bas, Murat

    2017-02-01

    The bradykinin B2 receptor antagonist icatibant is effective in angiotensin-converting enzyme inhibitor-induced angioedema. The drug is not approved officially for this indication and has to be administered in an emergency situation off-label. Corticosteroids or antihistamines do not seem to work in this condition. The effectiveness of C1-esterase-inhibitor in angiotensin-converting enzyme-induced angioedema must be verified in a double-blind study. Copyright © 2016 Elsevier Inc. All rights reserved.

  16. Combination solar photovoltaic heat engine energy converter

    Science.gov (United States)

    Chubb, Donald L.

    1987-01-01

    A combination solar photovoltaic heat engine converter is proposed. Such a system is suitable for either terrestrial or space power applications. The combination system has a higher efficiency than either the photovoltaic array or the heat engine alone can attain. Advantages in concentrator and radiator area and receiver mass of the photovoltaic heat engine system over a heat-engine-only system are estimated. A mass and area comparison between the proposed space station organic Rankine power system and a combination PV-heat engine system is made. The critical problem for the proposed converter is the necessity for high temperature photovoltaic array operation. Estimates of the required photovoltaic temperature are presented.

  17. Solar energy converter using surface plasma waves

    Science.gov (United States)

    Anderson, L. M. (Inventor)

    1984-01-01

    Sunlight is dispersed over a diffraction grating formed on the surface of a conducting film on a substrate. The angular dispersion controls the effective grating period so that a matching spectrum of surface plasmons is excited for parallel processing on the conducting film. The resulting surface plasmons carry energy to an array of inelastic tunnel diodes. This solar energy converter does not require different materials for each frequency band, and sunlight is directly converted to electricity in an efficient manner by extracting more energy from the more energetic photons.

  18. New strategy for optimizing wavelength converter placement

    Science.gov (United States)

    Foo, Y. C.; Chien, S. F.; Low, Andy L. Y.; Teo, C. F.; Lee, Youngseok

    2005-01-01

    This paper proposes a new strategic alternate-path routing to be combined with the particle swarm optimization (PSO) algorithm to better solve the wavelength converters placement problem. The strategic search heuristic is designed to provide network connectivity topologies for the converters to be placed more effectively. The new strategy is applied to the 14-node NSFNET to examine its efficiency in reducing the blocking probability in sparse wavelength conversion network. Computed results show that, when applied to the identical optimization framework, our search method outperforms both the equal-cost multipath routing and traffic-engineering-aware shortest-path routing.

  19. A linear temperature-to-frequency converter

    DEFF Research Database (Denmark)

    Løvborg, Leif

    1965-01-01

    , and that the maximum value of the temperature-frequency coefficient beta in this point is-1/3 alpha, where a is the temperature coefficient of the thermistor at the corresponding temperature. Curves showing the range in which the converter is expected to be linear to within plusmn0.1 degC are given. A laboratory......-built converter having beta = 1.0% degC-1 at 25degC is found to be linear to within plusmn0. 1 degC from 10 to 40degC....

  20. Performance Evaluation of Wave Energy Converters

    DEFF Research Database (Denmark)

    Pecher, Arthur

    . Guidelines for the development of wave energy converters recommend the use of different prototypes, having different sizes, which have to perform tank tests or sea trials. This implicates the need of different testing environment, which shifts from being controllable to uncontrollable with the development...... stages, and results thereby in a need for specific test objectives and procedures for each development stage. This PhD thesis has looked into the different development stages and more specifically in the performance assessment of wave energy converters based on tank testing and sea trials. The objective...

  1. Performance Evaluation of Wave Energy Converters

    DEFF Research Database (Denmark)

    Pecher, Arthur

    . Guidelines for the development of wave energy converters recommend the use of different prototypes, having different sizes, which have to perform tank tests or sea trials. Thisimplicates the need of different testing environment, which shifts from being controllable to uncontrollable with the development...... stages, and results thereby in a need for specific testobjectives and procedures for each development stage. This PhD thesis has looked into the different development stages and more specifically in the performance assessment of wave energy converters based on tank testing and sea trials. The objective...

  2. Dual Converter Fed Open-End Transformer Topology with Parallel Converters and Integrated Magnetics

    DEFF Research Database (Denmark)

    Gohil, Ghanshyamsinh Vijaysinh; Bede, Lorand; Teodorescu, Remus

    2016-01-01

    converter group comprises of two parallel Voltage Source Converters (VSCs), whose carrier signals are interleaved to improve the harmonic quality of the resultant switched output voltage of that converter group. However, an additional inductive component is required to suppress the circulating current...... that flows between the parallel interleaved VSCs. An integrated inductor is proposed which suppresses the circulating current in both the converter groups. In addition, the functionality of the line filter inductor is also integrated. Flux in various parts of the integrated inductor is analyzed and a design...... procedure is also described. The volume and the losses of the proposed solution are compared with that of the state-of-art solution. The control of the proposed converter system is also discussed. The analysis has been verified by the simulation and experimental results....

  3. National Ignition Facility frequency converter development

    International Nuclear Information System (INIS)

    Barker, C.E.; Auerbach, J.M.; Adams, C.H.

    1996-01-01

    A preliminary error budget for the third harmonic converter for the National Ignition Facility (NIF) laser driver has been developed using a root-sum-square-accumulation of error sources. Such a budget sets an upper bound on the allowable magnitude of the various effects that reduce conversion efficiency. Development efforts on crystal mounting technology and crystal quality studies are discussed

  4. Analysis of a phase-converter performance

    Energy Technology Data Exchange (ETDEWEB)

    Litchev, A.; Yanev, K. [Botswana Univ., Gaborone (Botswana). Dept. of Electrical Engineering

    2008-07-01

    A theoretical investigation of a phase converter consisting of static reactive elements was presented. The converter was connected to a 3-phase voltage supply and a large single-phase load in order to enable the symmetrical loading of all 3 phases. The parameters of the converter elements were determined in order to ensure that source phase currents functioned as part of a symmetrical system. Inductive and capacitive single-phase loads for the 3-phase system were also modelled. The power factor of the 3-phase source was unity at a purely active single-phase load. The source power factor decreased and remained lower than that of the load at inductive-resistive or capacitive-resistive loads. The source power factor was capacitive at inductive-resistive loads and capacitive-resistive when the source power factor was inductive. The theoretical study was compared with experimental data. Results of the investigation indicated that the static converter can be used to load 3-phase voltage systems with single-phase loads by maintaining supply symmetry. 6 refs., 2 tabs., 5 figs.

  5. Validating converted java code via symbolic execution

    NARCIS (Netherlands)

    Sneed, Harry M.; Verhoef, C.

    2017-01-01

    The testing approach described here has grown out of migration projects aimed at converting procedural programs in COBOL or PL/1 to object-oriented Java code. The code conversion itself is now automated but not completely. The human reengineer still has to make some adjustments to the automatically

  6. Converting skeletal structures to quad dominant meshes

    DEFF Research Database (Denmark)

    Bærentzen, Jakob Andreas; Misztal, Marek Krzysztof; Welnicka, Katarzyna

    2012-01-01

    We propose the Skeleton to Quad-dominant polygonal Mesh algorithm (SQM), which converts skeletal structures to meshes composed entirely of polar and annular regions. Both types of regions have a regular structure where all faces are quads except for a single ring of triangles at the center of eac...

  7. Mathematical modeling of the flash converting process

    Energy Technology Data Exchange (ETDEWEB)

    Sohn, H.Y.; Perez-Tello, M.; Riihilahti, K.M. [Utah Univ., Salt Lake City, UT (United States)

    1996-12-31

    An axisymmetric mathematical model for the Kennecott-Outokumpu flash converting process for converting solid copper matte to copper is presented. The model is an adaptation of the comprehensive mathematical model formerly developed at the University of Utah for the flash smelting of copper concentrates. The model incorporates the transport of momentum, heat, mass, and reaction kinetics between gas and particles in a particle-laden turbulent gas jet. The standard k-{epsilon} model is used to describe gas-phase turbulence in an Eulerian framework. The particle-phase is treated from a Lagrangian viewpoint which is coupled to the gas-phase via the source terms in the Eulerian gas-phase governing equations. Matte particles were represented as Cu{sub 2}S yFeS, and assumed to undergo homogeneous oxidation to Cu{sub 2}O, Fe{sub 3}O{sub 4}, and SO{sub 2}. A reaction kinetics mechanism involving both external mass transfer of oxygen gas to the particle surface and diffusion of oxygen through the porous oxide layer is proposed to estimate the particle oxidation rate Predictions of the mathematical model were compared with the experimental data collected in a bench-scale flash converting facility. Good agreement between the model predictions and the measurements was obtained. The model was used to study the effect of different gas-injection configurations on the overall fluid dynamics in a commercial size flash converting shaft. (author)

  8. Near-Shore Floating Wave Energy Converters

    DEFF Research Database (Denmark)

    Ruol, Piero; Zanuttigh, Barbara; Martinelli, Luca

    2011-01-01

    Aim of this note is to analyse the possible application of a Wave Energy Converter (WEC) as a combined tool to protect the coast and harvest energy. Physical model tests are used to evaluate wave transmission past a near-shore floating WEC of the wave activated body type, named DEXA. Efficiency...

  9. Angiotensin Converting Enzyme Insertion/Deletion Gene ...

    African Journals Online (AJOL)

    Purpose: This study investigated the influence of angiotensin-1 converting enzyme (ACE) insertiondeletion (ID) gene polymorphism on the treatment responses of type 2 diabetic subjects at varying stages of nephropathy to ACE inhibitors (ACEI) with regard to blood pressure (MAP) and renal response (GFR). Methods: The ...

  10. Hybrid switch for resonant power converters

    Science.gov (United States)

    Lai, Jih-Sheng; Yu, Wensong

    2014-09-09

    A hybrid switch comprising two semiconductor switches connected in parallel but having different voltage drop characteristics as a function of current facilitates attainment of zero voltage switching and reduces conduction losses to complement reduction of switching losses achieved through zero voltage switching in power converters such as high-current inverters.

  11. Power electronics converters for wind turbine systems

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Liserre, Marco; Ma, Ke

    2011-01-01

    The steady growth of installed wind power which reached 200 GW capacity in 2010, together with the up-scaling of the single wind turbine power capability - 7 MW’s has been announced by manufacturers - has pushed the research and development of power converters towards full scale power conversion,...

  12. Development of the Wave Energy Converter

    DEFF Research Database (Denmark)

    Kofoed, Jens Peter; Frigaard, Peter; Sørensen, Hans Christian

    2000-01-01

    The development of the wave energy converter Wave Dragon (WD) is presented. The WD is based on the overtopping principle. Initially a description of the WD is given. Then the development over time in terms of the various research and development projects working with the concept is described...

  13. Aquabuoy Wave Energy Converter

    DEFF Research Database (Denmark)

    Vicinanza, Diego; Margheritini, Lucia; Frigaard, Peter

    The work reported here is part of the contract agreement between the Finavera Renewables Ocean Energy Ltd. and the Department of Civil Engineering Hydraulics and Coastal Engineering Laboratory to instrument a model in scale 1:10 to prototype of the AquaBuOY (AB) wave energy converter and to analyse...

  14. Compact HVDC converter station design considerations

    Energy Technology Data Exchange (ETDEWEB)

    Lips, P.

    1976-01-01

    Possible means to reduce HVDC converter station land area requirements are shown. The split-up of real estate between the different kinds of equipment in present-day terminals is analyzed. From this, a priority list for suitable action to be taken is deducted. Three concepts of converter values suitable for compact converter stations are briefly discussed. By example of a 2400 MW terminal it is shown that with air-insulated liquid cooled thyristor valves a land area requirement of 0.8 m/sup 2//MW (8.5 sq. ft./MW) can be achieved, i.e., 1.2 percent of that required by the Pacific Intertie. Alternative solutions with metalclad valves are introduced and it is concluded that for converter stations with high rating in metropolitan areas, air-insulated liquid cooled thyristor valves seem to be the most appropriate choice. Where a low profile station is desirable, dead tank oil-insulated thyristor valves for outdoor mounting could be the optimum solution.

  15. Molecules for Converting Sunlight into Electricity

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 6; Issue 10. Molecules for Converting Sunlight into Electricity - Dye Sensitized Nanocrystalline-TiO2 based Photovoltaics. Ravi Mosurkal. General Article Volume 6 Issue 10 October 2001 pp 76-86 ...

  16. Online Scheduling in Distributed Message Converter Systems

    NARCIS (Netherlands)

    Risse, Thomas; Wombacher, Andreas; Surridge, Mike; Taylor, Steve; Aberer, Karl

    The optimal distribution of jobs among hosts in distributed environments is an important factor to achieve high performance. The optimal strategy depends on the application. In this paper we present a new online scheduling strategy for distributed EDI converter system. The strategy is based on the

  17. multilevel buck converter for automotive electrical load

    African Journals Online (AJOL)

    ... from internal combustion engine (ICE). The mass production of the hybrid electric (HE) and the electric vehicle (EV) is still awaited due to subsystem inefficiencies. Increasing the efficiencies of the power converters within subsystems of these HEVs and EVs will increase the performance of the new transportation vehicles.

  18. Catalytic Converters Maintain Air Quality in Mines

    Science.gov (United States)

    2014-01-01

    At Langley Research Center, engineers developed a tin-oxide based washcoat to prevent oxygen buildup in carbon dioxide lasers used to detect wind shears. Airflow Catalyst Systems Inc. of Rochester, New York, licensed the technology and then adapted the washcoat for use as a catalytic converter to treat the exhaust from diesel mining equipment.

  19. Convertible bonds and bank risk-taking

    NARCIS (Netherlands)

    Martynova, N.; Perotti, E.

    2015-01-01

    We study how contingent capital that converts in equity ahead of default affects bankrisk-shifting. Going concern conversion restores equity value in highly levered states,thus reducing heightened risk incentives. In contrast, conversion at default for traditionalbail-inable debt has no effect on

  20. Low Power 1-Bit ADC Array with Serial Output, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Microwave interferometers for NASA missions such as PATH and SCLP consist of up to 900 receivers. Each receiver requires I and Q ADCs (analog-to-digital converters)...

  1. High Performance ADC for Reconfigurable/Reprogrammable Communication Systems, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Ridgetop Group will develop a 3X improvement in sampling resolution over current state-of-the art analog-to-digital converter (ADC) technology to support...

  2. A Low Power Rad-Hard ADC for the KID Readout Electronics, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposal aims to develop a radiation hardened analog-to-digital converter (ADC) required for the Kinetic Inductance Detector (KID) readout electronics. KIDs are...

  3. Rad-Hard Sigma-Delta 3-channel ADC for Fluxgate Magnetometers, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed project aims to develop a multi-channel analog to digital converter (ADC) required for a fluxgate magnetometer (EPD) employed on NASA's planetary...

  4. SiGe 130 nm-based Rad-Hard ADC for the JEO Mission, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Ridgetop will demonstrate the feasibility of developing a radiation-hardened analog-to-digital converter (ADC) suitable for the Jupiter Europa Orbiter mission. This...

  5. High-Speed, Low-Power ADC for Digital Beam Forming (DBF) Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Ridgetop Group will design a high-speed, low-power silicon germanium (SiGe)-based, analog-to-digital converter (ADC) to be a key element for digital beam forming...

  6. High-Speed, Low-Power ADC for Digital Beam Forming (DBF) Systems Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In Phase 1, Ridgetop Group designed a high-speed, yet low-power silicon germanium (SiGe)-based, analog-to-digital converter (ADC) to be a key element for digital...

  7. High-Speed, Low-Power ADC for Digital Beam Forming (DBF) Systems, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Ridgetop Group will design a high-speed, low-power silicon germanium (SiGe)-based, analog-to-digital converter (ADC) to be a key element for digital beam forming...

  8. Delta-Sigma Modulated Photodetection Method to Reduce Laser Power Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This delta-sigma technique may be thought of as a form of analog-to-digital converter (ADC). The proposed network offers a means of processing electronic signals...

  9. 20GSps 6-bit Low-Power Rad-Tolerant ADC, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed project aims to develop a 20GSps 6-bit radiation hardened analog to digital converter (ADC) required for microwave radiometers being developed for space...

  10. Analysis of parallel optical sampling rate and ADC requirements in digital coherent receivers

    DEFF Research Database (Denmark)

    Lorences Riesgo, Abel; Galili, Michael; Peucheret, Christophe

    2012-01-01

    We comprehensively assess analog-to-digital converter requirements in coherent digital receiver schemes with parallel optical sampling. We determine the electronic requirements in accordance with the properties of the free running local oscillator....

  11. High-Speed, Low-Power ADC for Digital Beam Forming (DBF) Systems, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — In Phase 1, Ridgetop Group designed a high-speed, yet low-power silicon germanium (SiGe)-based, analog-to-digital converter (ADC) to be a key element for digital...

  12. Extremelly High Bandwidth Rad Hard Data Acquisition System, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — Analog-to-digital converters (ADCs) are the key components for digitizing high-speed analog data in modern data acquisition systems, which is a critical part of...

  13. Bidirectional converter interface for a battery energy storage test bench

    DEFF Research Database (Denmark)

    Trintis, Ionut; Thomas, Stephan; Blank, Tobias

    2011-01-01

    This paper presents the bidirectional converter interface for a 6 kV battery energy storage test bench. The power electronic interface consists a two stage converter topology having a low voltage dc-ac grid connected converter and a new dual active bridge dc-dc converter with high transformation...

  14. Do Convertible Bond Issuers Cater to Investor Demand?

    NARCIS (Netherlands)

    de Jong, Abe; Duca, Eric; Dutordoir, Marie

    2013-01-01

    We examine the impact of fluctuations in investor demand for convertible securities on convertible bond issue volumes, pricing, and design. We find evidence of a positive impact of investor demand proxies on convertible bond issue volumes. We also document significantly lower convertible bond

  15. Methods for Converter Sludge Dehydration Intensification

    Science.gov (United States)

    Vakhromeev, M. I.; Moreva, Y. A.; Starkova, L. G.

    2017-11-01

    The article considers the intensification methods for converter sludge dehydration exemplified by the sludges of the Oxygen Converter Workshop (OCW) of the Open Joint-Stock Company “Magnitogorsk Iron and Steel Works” (MMK, OJSC), one of the largest metallurgical companies in the Southern Urals. Converter sludges can contain up to 45-70% of ferrum [21] which is interesting in terms of their use as an addition to a sinter-feed mixture. Sludge intensifies the sintering process. It positively influences pelletizing and fusion mixture melting dynamics at sintering. Over the period of the converter sludge dehydration complex operation at the OCW, MMK, OJSC, it was revealed that processing results in obtaining of high humidity sludge. It causes sludge freezing during the winter period, thus, its transportation involves extra costs for sludge warming up. To resolve the above-mentioned problem, the following works were performed in 2016: - experimental studies of how the application of the low-molecular anionic flocculate “SEURVEY” FL-3 influences sludge humidity reduction. - experimental studies of how the filtering press process operation parameters influence sludge humidity reduction. The new flocculate application didn't lower the dehydrated sludge humidity (the objective was the humidity of not more than 15%). Basing upon the conducted research results, we can make a conclusion that putting into operation the sewage water reactant treatment technology with the use of “SEURVEY”, FL-3 (H-10) is not recommended. The research of the influence the filtering press process parameters have on the dehydration process intensification demonstrated that reaching of the obtained residue humidity value lower than 15% is possible under the reduction of the filtering press chamber depths to 30 mm and with the application of additional operation “Residue drying” with compressed air. This way of the sludge dehydration problem resolving at filtering presses of the

  16. Bidirectional converter interface for a battery energy storage test bench

    DEFF Research Database (Denmark)

    Trintis, Ionut; Thomas, Stephan; Blank, Tobias

    2011-01-01

    This paper presents the bidirectional converter interface for a 6 kV battery energy storage test bench. The power electronic interface consists a two stage converter topology having a low voltage dc-ac grid connected converter and a new dual active bridge dc-dc converter with high transformation...... ratio. The dc-dc converter controls the battery charge/discharge current while the grid converter controls the common dc-link voltage and the grid current. The applied control structures and the hardware implementation of both converters are presented, together with their interaction. Experimental...

  17. Dividend-Protected Convertible Bonds and the Disappearance

    OpenAIRE

    Grundy, Bruce D.; Verwijmeren, Patrick

    2012-01-01

    Firms have not historically called their convertible bonds as soon as they could force conversion. Various explanations for the delay rely on the size of the dividends that bondholders forgo so long as they do not convert. We investigate an important change in convertible security design, namely that more than 95 percent of recent convertible bond issues are dividend-protected. Dividend protection means that the conversion value of the shares into which a bond is convertible is unaffected by ...

  18. Imbalance between pulmonary angiotensin-converting enzyme and angiotensin-converting enzyme 2 activity in acute respiratory distress syndrome

    NARCIS (Netherlands)

    Wosten-van Asperen, Roelie M.; Bos, Albert; Bem, Reinout A.; Dierdorp, Barbara S.; Dekker, Tamara; van Goor, Harry; Kamilic, Jelena; van der Loos, Chris M.; van den Berg, Elske; Bruijn, Martijn; van Woensel, Job B.; Lutter, Rene

    2013-01-01

    Objective: Angiotensin-converting enzyme and its effector peptide angiotensin II have been implicated in the pathogenesis of acute respiratory distress syndrome. Recently, angiotensin-converting enzyme 2 was identified as the counter-regulatory enzyme of angiotensin-converting enzyme that converts

  19. Imbalance between pulmonary angiotensin-converting enzyme and angiotensin-converting enzyme 2 activity in acute respiratory distress syndrome

    NARCIS (Netherlands)

    Wösten-van Asperen, Roelie M.; Bos, Albert P.; Bem, Reinout A.; Dierdorp, Barbara S.; Dekker, Tamara; van Goor, Harry; Kamilic, Jelena; van der Loos, Chris M.; van den Berg, Elske; Bruijn, Martijn; van Woensel, Job B.; Lutter, René

    2013-01-01

    Angiotensin-converting enzyme and its effector peptide angiotensin II have been implicated in the pathogenesis of acute respiratory distress syndrome. Recently, angiotensin-converting enzyme 2 was identified as the counter-regulatory enzyme of angiotensin-converting enzyme that converts angiotensin

  20. Architecture and Application of Time Quantizing ADCs

    Science.gov (United States)

    2017-03-01

    Analog to Digital Converter; Signal to Quantization Noise Ratio; Non-Uniform Sampling. INTRODUCTION Traditional analog to digital converters...LIMITS In order to verify these results, a MATLAB ™ routine was written which processes a sine wave of voltage vs time into data points quantized in...SQNR, th eed to be con domain. This crete Fourier interpolation o nd performing uniform disc bitive in real-t polate to unifo R of an Ideal N MATLAB

  1. Multi-output DC-DC converters based on diode-clamped converters configuration

    DEFF Research Database (Denmark)

    Nami, A.; Zare, F.; Ghosh, A.

    2010-01-01

    for a diode-clamed inverter in the grid connection systems, where boosting low rectified output-voltage and series DC link capacitors is required. To verify the proposed topology, steady-state and dynamic analyses of a MOB converter are examined. A simple control strategy has been proposed to demonstrate......This study presents a new DC DC multi-output boost (MOB) converter which can share its total output between different series of output voltages for low- and high-power applications. This configuration can be utilised instead of several single output power supplies. This is a compatible topology...... the performance of the proposed topology for a double-output boost converter. The topology and its control strategy can easily be extended to offer multiple outputs. Simulation and experimental results are presented to show the validity of the control strategy for the proposed converter....

  2. Strained quantum well photovoltaic energy converter

    Science.gov (United States)

    Freundlich, Alexandre (Inventor); Renaud, Philippe (Inventor); Vilela, Mauro Francisco (Inventor); Bensaoula, Abdelhak (Inventor)

    1998-01-01

    An indium phosphide photovoltaic cell is provided where one or more quantum wells are introduced between the conventional p-conductivity and n-conductivity indium phosphide layer. The approach allows the cell to convert the light over a wider range of wavelengths than a conventional single junction cell and in particular convert efficiently transparency losses of the indium phosphide conventional cell. The approach hence may be used to increase the cell current output. A method of fabrication of photovoltaic devices is provided where ternary InAsP and InGaAs alloys are used as well material in the quantum well region and results in an increase of the cell current output.

  3. Flower-petal mode converter for NLC

    International Nuclear Information System (INIS)

    Hoag, H.A.; Tantawi, S.G.; Callin, R.; Deruyter, H.; Farkas, Z.D.; Ko, K.; Kroll, N.; Lavine, T.L.; Menegat, A.; Vlieks, A.E.

    1993-01-01

    It is important to minimize power loss in the waveguide system connecting klystron, pulse-compressor, and accelerator in an X-Band NLC. However, existing designs of klystron output cavity circuits and accelerator input couplers utilize rectangular waveguide which has relatively high transmission loss. It is therefore necessary to convert to and from the low-loss mode in circulator waveguide at each end of the system. A description is given of development work on high-power, high-vacuum open-quote flower-petal close-quote transducers, which convert the TE 10 mode in rectangular guide to the TE 01 mode in circular guide. A three-port modification of the flower petal device, which can be used as either a power combiner at the klystron or a power divider at the accelerator is also described

  4. Converter topologies for common mode voltage reduction

    Science.gov (United States)

    Rodriguez, Fernando

    2017-11-21

    An inverter includes a three-winding transformer, a DC-AC inverter electrically coupled to the first winding of the transformer, a cycloconverter electrically coupled to the second winding of the transformer, and an active filter electrically coupled to the third winding of the transformer. The DC-AC inverter is adapted to convert the input DC waveform to an AC waveform delivered to the transformer at the first winding. The cycloconverter is adapted to convert an AC waveform received at the second winding of the transformer to the output AC waveform having a grid frequency of the AC grid. The active filter is adapted to sink and source power with one or more energy storage devices based on a mismatch in power between the DC source and the AC grid. At least two of the DC-AC inverter, the cycloconverter, or the active filter are electrically coupled via a common reference electrical interconnect.

  5. Flower-petal mode converter for NLC

    International Nuclear Information System (INIS)

    Hoag, H.A.; Tantawi, S.G.; Callin, R.

    1993-04-01

    It is important to minimize power loss in the waveguide system connecting klystron, pulse-compressor, and accelerator in an X-Band NLC. However, existing designs of klystron output cavity circuits and accelerator input couplers utilize rectangular waveguide which has relatively high transmission loss. It is therefore necessary to convert to and from the low-loss mode in circular waveguide at each end of the system. A description is given of development work on high-power, high-vacuum 'flower-petal' transducers, which convert the TE 10 mode in rectangular guide to the TE 01 mode in circular guide. A three-port modification of the flower petal device, which can be used as either a power combiner at the klystron or a power divider at the accelerator is also described

  6. MAGIC: Model and Graphic Information Converter

    Science.gov (United States)

    Herbert, W. C.

    2009-01-01

    MAGIC is a software tool capable of converting highly detailed 3D models from an open, standard format, VRML 2.0/97, into the proprietary DTS file format used by the Torque Game Engine from GarageGames. MAGIC is used to convert 3D simulations from authoritative sources into the data needed to run the simulations in NASA's Distributed Observer Network. The Distributed Observer Network (DON) is a simulation presentation tool built by NASA to facilitate the simulation sharing requirements of the Data Presentation and Visualization effort within the Constellation Program. DON is built on top of the Torque Game Engine (TGE) and has chosen TGE's Dynamix Three Space (DTS) file format to represent 3D objects within simulations.

  7. MOCCASIN: converting MATLAB ODE models to SBML.

    Science.gov (United States)

    Gómez, Harold F; Hucka, Michael; Keating, Sarah M; Nudelman, German; Iber, Dagmar; Sealfon, Stuart C

    2016-06-15

    MATLAB is popular in biological research for creating and simulating models that use ordinary differential equations (ODEs). However, sharing or using these models outside of MATLAB is often problematic. A community standard such as Systems Biology Markup Language (SBML) can serve as a neutral exchange format, but translating models from MATLAB to SBML can be challenging-especially for legacy models not written with translation in mind. We developed MOCCASIN (Model ODE Converter for Creating Automated SBML INteroperability) to help. MOCCASIN can convert ODE-based MATLAB models of biochemical reaction networks into the SBML format. MOCCASIN is available under the terms of the LGPL 2.1 license (http://www.gnu.org/licenses/lgpl-2.1.html). Source code, binaries and test cases can be freely obtained from https://github.com/sbmlteam/moccasin : mhucka@caltech.edu More information is available at https://github.com/sbmlteam/moccasin. © The Author 2016. Published by Oxford University Press.

  8. Spectral converters and luminescent solar concentrators

    Energy Technology Data Exchange (ETDEWEB)

    Scudo, Petra F.; Abbondanza, Luigi; Fusco, Roberto; Caccianotti, Luciano [Eni S.p.A, Research Center for Non-Conventional Energies - Istituto ENI Donegani, Via G.Fauser 4, 28100 Novara (Italy)

    2010-07-15

    In this paper we present a comprehensive theoretical description of molecular spectral converters in the specific context of luminescent solar concentrators (LSCs). The theoretical model is an extension to a three-level system interacting with a solar radiation bath of the standard quantum theory of atomic radiative processes. We derive the equilibrium equations of the conversion process and provide specific examples of application of this principle to the development of solar concentration devices. (author)

  9. Passive components used in power converters

    OpenAIRE

    Rufer, A; Veestra, M; Barrade, P

    2006-01-01

    In power converters, passive components play an important role, and have in general specific nature and properties. The goal of this tutorial is to give an overview, first on inductive components for power conversion, and second on dedicated power capacitors. In a third part, new components— supercapacitors—will be presented. Generally, inductors for power applications must be custom designed. In this tutorial, the most important effects encountered when realising inductive components will be...

  10. MOCCASIN: converting MATLAB ODE models to SBML

    OpenAIRE

    G?mez, Harold F.; Hucka, Michael; Keating, Sarah M.; Nudelman, German; Iber, Dagmar; Sealfon, Stuart C.

    2016-01-01

    Summary: MATLAB is popular in biological research for creating and simulating models that use ordinary differential equations (ODEs). However, sharing or using these models outside of MATLAB is often problematic. A community standard such as Systems Biology Markup Language (SBML) can serve as a neutral exchange format, but translating models from MATLAB to SBML can be challenging?especially for legacy models not written with translation in mind. We developed MOCCASIN (Model ODE Converter for ...

  11. Generalized modular multilevel converter and modulation

    DEFF Research Database (Denmark)

    Liu, Hui; Loh, Poh Chiang; Blaabjerg, Frede

    2014-01-01

    Modular multilevel converter (MMC) has gained popularity recently with its modulation, capacitor voltage balancing and circulating current issues widely discussed. Contributing to this effort, a study is presented here to show how the MMC topology can be derived from the viewpoint of two series....... For controlling the GMMC, a simple modulation scheme is also presented, where the goal is to achieve the desired performance at a minimized complexity. Simulation results are presented to illustrate the operation of the proposed topology....

  12. Characteristics of image converters and image intensifiers

    International Nuclear Information System (INIS)

    Gurvich, A.M.; Shamanov, A.A.; Rozenberg, A.M.; Fajnberg, V.S.; Kavtorova, V.P.; Salyuk, L.V.; Yakovleva, F.B.

    1978-01-01

    The characteristics of image converters and image intensifiers, which determine the range of the X-radiation dose rates used and the image quality, are considered. The equations for calculating the requirements to be imposed on the separate intensifier elements from known parameters of other elements with an allowance for the nonlinearity of the television system and the role of fluctuation in the space distribution of X-radiation quanta are given

  13. H- ion production from different converter materials

    International Nuclear Information System (INIS)

    Leung, K.N.; Ehlers, K.W.

    1984-10-01

    For heating plasmas and for current drive in some fusion reactors, high energy neutral beams may be required. The high neutralization efficiency of H - or D - ions makes them favorable to form neutral atoms with energies in excess of 160 keV. It has been shown that a steady-state H - ion beam with current greater than 1 A can be generated by a surface conversion type source with Mo being used as the converter material. In order to achieve the proper cesium coverage and thereby increasing the H - ion yield, the application of porous cesium-dispensing converters is being investigated. It is also possible to optimize the H - production by choosing the proper converter material. In this paper, we compare the negative ion yield generated by different materials (such as Mo, Ti, V, Nb, Pt, Pd, Rh, Cu, Ta, Al, Au, LaB 6 and stainless-steel) in the pure hydrogen and cesium-hydrogen modes of operation

  14. Converter fed sub sea motor drives

    Energy Technology Data Exchange (ETDEWEB)

    Raad, R.O.

    1995-09-01

    Minor offshore gas and oil resources located 20-50 km from existing installations may often be commercially exploited only by use of complete sub sea solutions. This thesis deals with analyses of a sub sea adjustable speed electric motor which is fed by a frequency converter via a long cable (up to 50 km) between the converter and the motor. The author develops a general model for analysing such motor drive systems with the objective of verifying the feasibility of specific applications and of specifying the requirements on the system components. The simulation model is used to identify the critical frequency ranges in which the converter must not generate significant harmonics, to verify the start-up strategy chosen, and to verify the stability with potential disturbances applied to the system. Simulation models are developed for both transient and steady state analyses. They are accurate up to 5 kHz and can incorporate the frequency dependency of the motor and cable parameters. Ideal thyristors and diodes are used. The models are implemented in existing simulation tools. Most of the results relate to a base case with a 670 kW squirrel cage motor fed from a 30 km long cable, but cases with 3 MW rating or with 50 km cable have also been analyzed and found to be feasible. Each specific application must be separately studied. Results of simulation calculations are presented and conclusions given. 53 refs., 124 figs., 23 tabs.

  15. One-Quadrant Switched-Mode Power Converters

    CERN Document Server

    Petrocelli, R.

    2015-06-15

    This article presents the main topics related to one-quadrant power convert- ers. The basic topologies are analysed and a simple methodology to obtain the steady-state output–input voltage ratio is set out. A short discussion of dif- ferent methods to control one-quadrant power converters is presented. Some of the reported derived topologies of one-quadrant power converters are also considered. Some topics related to one-quadrant power converters such as syn- chronous rectification, hard and soft commutation, and interleaved converters are discussed. Finally, a brief introduction to resonant converters is given.

  16. EVALUATING CONVERTIBLE, CALLABLE AND REDEEMABLE BONDS

    OpenAIRE

    GIULIANO CARROZZA UZEDA IORIO DE SOUZA

    2006-01-01

    Em artigo publicado em 1986 no Journal of Finance, LYON Taming [35], John McConnell e Eduardo Schwartz desenvolveram um modelo para apreçamento do Liquid Yield Option Notes (LYON), um título que não contempla o pagamento de cupom, em que o investidor possui opção de venda e o direito de convertê-lo em um determinado número de ações do emissor que, por sua vez, possui opção de compra, na qual, assim como no caso da opção de venda, o ativo objeto é o pr...

  17. Layout Optimisation of Wave Energy Converter Arrays

    DEFF Research Database (Denmark)

    Ruiz, Pau Mercadé; Nava, Vincenzo; Topper, Mathew B. R.

    2017-01-01

    This paper proposes an optimisation strategy for the layout design of wave energy converter (WEC) arrays. Optimal layouts are sought so as to maximise the absorbed power given a minimum q-factor, the minimum distance between WECs, and an area of deployment. To guarantee an efficient optimisation......, a four-parameter layout description is proposed. Three different optimisation algorithms are further compared in terms of performance and computational cost. These are the covariance matrix adaptation evolution strategy (CMA), a genetic algorithm (GA) and the glowworm swarm optimisation (GSO) algorithm...

  18. Waste Plastic Converting into Hydrocarbon Fuel Materials

    Energy Technology Data Exchange (ETDEWEB)

    Sarker, Moinuddin; Mamunor Rashid, Mohammad; Molla, Mohammad

    2010-09-15

    The increased demand and high prices for energy sources are driving efforts to convert organic compounds into useful hydrocarbon fuels. Although much of this work has focused on biomass, there are strong benefits to deriving fuels from waste plastic material. Natural State Research Inc. (NSR) has invented a simple and economically viable process to decompose the hydrocarbon polymers of waste plastic into the shorter chain hydrocarbon of liquid fuel (patent pending). The method and principle of the production / process will be discussed. Initial tests with several widely used polymers indicate a high potential for commercialization.

  19. Power converters for medium voltage networks

    CERN Document Server

    Islam, Md Rabiul; Zhu, Jianguo

    2014-01-01

    This book examines a number of topics, mainly in connection with advances in semiconductor devices and magnetic materials and developments in medium and large-scale renewable power plant technologies, grid integration techniques and new converter topologies, including advanced digital control systems for medium-voltage networks. The book's individual chapters provide an extensive compilation of fundamental theories and in-depth information on current research and development trends, while also exploring new approaches to overcoming some critical limitations of conventional grid integration te

  20. Hot carrier metamaterial detectors and energy converters

    Science.gov (United States)

    Krayer, Lisa; Munday, Jeremy N.

    Metamaterials can be used to manipulate the flow of light in ways not typically available with traditional materials. Beyond their optical properties, metamaterials can be used as the basis for optoelectronic devices through the incorporation of a metal-semiconductor interface. The absorbed radiation in the metal can excite surface plasmons, which nonradiatively decay into hot electrons or holes that can be injected into the base semiconductor and contribute to photocurrent generation. In this talk, we will present our latest work on metamaterial photo-detectors and solar energy converters.

  1. Faults and Diagnosis Systems in Power Converters

    DEFF Research Database (Denmark)

    Lee, Kyo-Beum; Choi, Uimin

    2014-01-01

    efforts have been put into making these systems better in terms of reliability in order to achieve high power source availability, reduce the cost of energy and also increase the reliability of overall systems. Among the components used in power converters, a power device and a capacitor fault occurs most...... frequently. Therefore, it is important to monitor the power device and capacitor fault to increase the reliability of power electronics. In this chapter, the diagnosis methods for power device fault will be discussed by dividing into open- and short-circuit faults. Then, the condition monitoring methods...

  2. A Hybrid Modular Multilevel Converter with Partial Embedded Energy Storage

    Directory of Open Access Journals (Sweden)

    Georgios Konstantinou

    2016-11-01

    Full Text Available Modular and cascaded multilevel converters provide a functional solution for the integration of energy storage systems (ESSs. This paper develops a hybrid multilevel converter based on the modular multilevel converter (MMC that can be functionally extended with partial embedded ESS as a fraction of the overall converter power rating. The configuration, which can operate as a typical DC-AC converter, enables multi-directional power flow between the DC- and AC-side of the converter, as well as the embedded energy storage elements. The use of a three-phase flying-capacitor submodule eliminates the second-order harmonic oscillations present in modular cascaded multilevel converters. Current, voltage and power control are discussed in the paper while simulation results illustrate the operation of the hybrid MMC as a DC-AC converter in a typical inverter application and the additional functions and control of the embedded ESS.

  3. Matrix converter applied to energy saving for street lighting systems

    OpenAIRE

    Román Lumbreras, Manuel; Velasco Quesada, Guillermo; Conesa Roca, Alfons

    2010-01-01

    This work presents a three-phase AC-AC converter, with independent phase control, based on matrix-converter structure. This converter is applied to electrical energy saving on the public lighting systems by means of regulation and control of the voltage applied to the lamps. The developed converter represents a technological improvement with respect to the traditional systems based on an autotransformer: it reduces system cost and volume, and increases lamps lifetime.

  4. A New Modular Multilevel Converter with Integrated Energy Storage

    DEFF Research Database (Denmark)

    Trintis, Ionut; Munk-Nielsen, Stig; Teodorescu, Remus

    2011-01-01

    This paper introduces a new modular converter with integrated energy storage based on the cascaded half-bridge modular multilevel converter with common DC bus. It represents a complete modular solution with power electronics and energy storage building blocks, for medium and high voltage...... in the future HVDC meshed grids. Its functionality and flexibility makes the converter independent on the energy storage unit characteristic. The converter concept with its basic functions and control schemes are described and evaluated in this paper....

  5. New active load voltage clamp for HF-link converters

    DEFF Research Database (Denmark)

    Ljusev, Petar; Andersen, Michael Andreas E.

    2005-01-01

    This paper proposes a new active clamp for HF-link converters, which features very high efficiency by returning the clamped energy back to the primary side through a small auxiliary converter. It also increases the reliability of HF-link converters by providing an alternative load current path du...

  6. Sheppard-Taylor Isolated High Boost DC-DC Converter

    DEFF Research Database (Denmark)

    Chub, Andrii; Siwakoti, Yam Prasad; Vinnikov, Dmitri

    2017-01-01

    This paper presents a new galvanically isolated step-up dc-dc converter intended for low-power but high step-up applications. The proposed converter is capable of regulating output voltage within a wide range of the input voltage or load variations. In contrast to competitors, the converter can b...

  7. A nine-level hybrid symmetric cascaded multilevel converter for ...

    Indian Academy of Sciences (India)

    Indrajit Sarkar

    Abstract. A nine-level hybrid symmetric cascaded multilevel converter (MLC) fed induction motor drive is proposed in this paper. The proposed converter is capable of producing nine output voltage levels by using the same number of power cells as that of conventional five-level symmetric cascaded H-bridge converter.

  8. Multistage switched inductor boost converter for renewable energy application

    DEFF Research Database (Denmark)

    Maroti, Pandav Kiran; Padmanaban, Sanjeevikumar; Bhaskar, Mahajan Sagar

    2017-01-01

    In this paper Multistage Switched Inductor Boost Converter (Multistage SIBC) is uttered for renewable energy applications. The projected converter is derived from an amalgamation of the conventional step-up converter and inductor stack. The number of inductor and duty ratio decides the overall...

  9. Use of Electrically Heated Metal Catalytic Converter in Cold Starting ...

    African Journals Online (AJOL)

    The easiest way to preheat the converter is to use electric resistance heaters. The electrical systems on most cars provide enough energy or power to heat the catalytic converter fast enough. So, in this research the main converter remains its usual position, whereas the heated catalyst is placed close to the exhaust manifold ...

  10. A nine-level hybrid symmetric cascaded multilevel converter for ...

    Indian Academy of Sciences (India)

    A nine-level hybrid symmetric cascaded multilevel converter (MLC) fed induction motor drive is proposed in this paper. The proposed converter is capable of producing nine output voltage levels by using the same number of power cells as that of conventional five-level symmetric cascaded H-bridge converter. Eachphase in ...

  11. New active load voltage clamp for HF-link converters

    DEFF Research Database (Denmark)

    Ljusev, Petar; Andersen, Michael Andreas E.

    2005-01-01

    This paper proposes a new active clamp for HF-link converters, which features very high efficiency by returning the clamped energy back to the primary side through a small auxiliary converter. It also increases the reliability of HF-link converters by providing an alternative load current path...

  12. Fault isolation in parallel coupled wind turbine converters

    DEFF Research Database (Denmark)

    Odgaard, Peter Fogh; Thøgersen, Paul Bach; Stoustrup, Jakob

    2010-01-01

    Parallel converters in wind turbine give a number advantages, such as fault tolerance due to the redundant converters. However, it might be difficult to isolate gain faults in one of the converters if only a combined power measurement is available. In this paper a scheme using orthogonal power re...

  13. Efficiency and reliability improvement in wind turbine converters by grid converter adaptive control

    DEFF Research Database (Denmark)

    Trintis, Ionut; Munk-Nielsen, Stig; Abrahamsen, Flemming

    2013-01-01

    This paper presents a control method that reduces the losses in wind turbine converters adaptively controlling the grid converter. The dc-link voltage adapts its reference based on the system state and therefore reduces the stored energy, and is therefore kept at the minimum necessary for the grid...... and generator side. Operating in this way, the electrical and thermal stress factors are decreased on the power electronic devices, increasing their lifetime. The simulation results using this method show efficiency increase and devices temperature cycles slightly decreased. Experimental results on a wind...

  14. Sulfur dioxide converter and pollution arrester system

    International Nuclear Information System (INIS)

    Montalvo, V.H.

    1983-01-01

    A sulphur dioxide converter and pollution arrester system are disclosed which involves the treatment of smoke and/or contaminated air emanating from a combustion area by passage through a zone achieving turbulence into a water spray contained first treating chamber. The turbulence zone, into which an atomized catalyst is introduced, serves to create a longer path for cooling as well as increased centrifugal motion to the solid particles in the contaminated air and also the formation of sulphur trioxide. In other words, the arrangement is such that pollution arresting action is provided in the form of ''slinging'' resulting from tangential directional movement and, when combining with the water spray in the first treating chamber, the ultimate formation of sulphuric acid. Subsequently, the contaminated air, containing amounts of sulphurous and sulphuric acids, passes through a second treating chamber, where airflow throughout the system is occasioned by action at the outlet end, such as the vacuum created by a flue and not by independent mechanical means. The arrangement serves to a twofold purpose, i.e. to minimize or arrest pollution and to convert sulphur dioxide, a component of high sulphur coal, into commercially valuable sulphuric acid

  15. Converting DYNAMO simulations to Powersim Studio simulations

    Energy Technology Data Exchange (ETDEWEB)

    Walker, La Tonya Nicole; Malczynski, Leonard A.

    2014-02-01

    DYNAMO is a computer program for building and running 'continuous' simulation models. It was developed by the Industrial Dynamics Group at the Massachusetts Institute of Technology for simulating dynamic feedback models of business, economic, and social systems. The history of the system dynamics method since 1957 includes many classic models built in DYANMO. It was not until the late 1980s that software was built to take advantage of the rise of personal computers and graphical user interfaces that DYNAMO was supplanted. There is much learning and insight to be gained from examining the DYANMO models and their accompanying research papers. We believe that it is a worthwhile exercise to convert DYNAMO models to more recent software packages. We have made an attempt to make it easier to turn these models into a more current system dynamics software language, Powersim © Studio produced by Powersim AS2 of Bergen, Norway. This guide shows how to convert DYNAMO syntax into Studio syntax.

  16. Matrix-form radiation image converter

    International Nuclear Information System (INIS)

    Reiss, K.H.

    1975-01-01

    An image converter is used to make visible images produced by gamma rays or similar penetrating rays like X-rays, etc., by transforming the distribution of ray density contained in a bundle of rays carrying the image which is to be made visible, by means of a cathode and an anode spaced from the cathode. The space between the electrodes contains a gas and the electrodes are subjected to a voltage which produces electrical discharges during ray penetration at corresponding locations depending upon the rays. The cathode as well as the anode consists of a plurality of parts having large surfaces which extend at least approximately perpendicularly to the ray incoming surface of the converter, so that the electric field extends parallel to this surface. The invention is particularly characterized in that the gas is under pressure in the range of 10 at., that the applied voltage makes certain the operation in the proportional range and that parts of the anode and of the cathode are combined in rows. Rows of the cathode elements and those of the anode extend at an angle to each other, the rows being connected electrically with a device for forming an electronic intensity center which produces representable local signals for orientation of the discharge bundle striking the anode

  17. Forback DC-to-DC converter

    Science.gov (United States)

    Lukemire, Alan T.

    1995-05-01

    A pulse-width modulated DC-to-DC power converter including a first inductor, i.e. a transformer or an equivalent fixed inductor equal to the inductance of the secondary winding of the transformer, coupled across a source of DC input voltage via a transistor switch which is rendered alternately conductive (ON) and nonconductive (OFF) in accordance with a signal from a feedback control circuit is described. A first capacitor capacitively couples one side of the first inductor to a second inductor which is connected to a second capacitor which is coupled to the other side of the first inductor. A circuit load shunts the second capacitor. A semiconductor diode is additionally coupled from a common circuit connection between the first capacitor and the second inductor to the other side of the first inductor. A current sense transformer generating a current feedback signal for the switch control circuit is directly coupled in series with the other side of the first inductor so that the first capacitor, the second inductor and the current sense transformer are connected in series through the first inductor. The inductance values of the first and second inductors, moreover, are made identical. Such a converter topology results in a simultaneous voltsecond balance in the first inductance and ampere-second balance in the current sense transformer.

  18. Fundamental study on alkali metal thermoelectric converter

    International Nuclear Information System (INIS)

    Masuda, Toshihisa

    1989-01-01

    The alkali metal thermoelectric converter (AMTEC) utilizing the sodium ion conducting β''-alumina is a device to convert heat energy to electric energy directly. In this paper, the results of theoretical and experimental studies on AMTEC power generating characteristics, internal electrical resistances of single cell, and system analysis of AMTEC power generating systems are reported. This paper consists of 5 chapters, which are summarized as follows: In chapter 1, a theoretical explanation of AMTEC, a brief survey of the research and development history of AMTEC and a purpose of this paper are reported. In chapter 2, the properties of β''-alumina, preparations of thin film electrodes, and special attention points to be paid in handling of β''-alumina and film electrodes are reported. The AMTEC power generating characteristics of the tubular cells are also reported. In chapter 3, the experimental results of the disk type cells and the theoretical considerations about internal resistances are reported. The causes of electrode erosion are also reported. In chapter 4, the system analysis on AMTEC steam-turbine combined cycle for a dispersed power station and AMTEC power system for a aerospace power are reported. Chapter 5 summarizes major results achieved in the preceding four chapters as a concluding remark. (J.P.N.) 62 refs

  19. CCLIBS: The CERN Power Converter Control Libraries

    CERN Document Server

    AUTHOR|(SzGeCERN)404953; Lebioda, Krzysztof Tomasz; Magrans De Abril, Marc; Martino, Michele; Murillo Garcia, Raul; Nicoletti, Achille

    2015-01-01

    Accurate control of power converters is a vital activity in large physics projects. Several different control scenarios may coexist, including regulation of a circuit’s voltage, current, or field strength within a magnet. Depending on the type of facility, a circuit’s reference value may be changed asynchronously or synchronously with other circuits. Synchronous changes may be on demand or under the control of a cyclic timing system. In other cases, the reference may be calculated in real-time by an outer regulation loop of some other quantity, such as the tune of the beam in a synchrotron. The power stage may be unipolar or bipolar in voltage and current. If it is unipolar in current, it may be used with a polarity switch. Depending on the design, the power stage may be controlled by a firing angle or PWM duty-cycle reference, or a voltage or current reference. All these cases are supported by the CERN Converter Control Libraries (CCLIBS). These open-source C libraries include advanced reference generati...

  20. Contingent convertible bonds as countercyclical capital measures

    Directory of Open Access Journals (Sweden)

    Francois Liebenberg

    2017-06-01

    Aim: The effectiveness of the CCB during contractions is not obvious. Contingent convertible (CoCo bonds – which are bond-like until triggered by a deterioration of a prescribed capital metric, at which point they convert into a form of equity – are explored as a supplementary countercyclical capital measure for such periods to establish whether or not they function effectively. Setting: The analysis is undertaken using global bank CoCo data, and then applied to South African banks. Methods: The Hodrick Prescott filter was applied to empirical historical data. Results: The CCB functions as a good countercyclical capital measure in times of economic expansion by absorbing losses and stabilising the capital base through equity issuance. Conclusion: The issuance of CoCo bonds – if their trigger mechanisms are designed correctly – may prove helpful to banks and the broader financial sector in times of economic contraction through the countercyclical capital properties that manifest through CoCo bonds under these economic conditions.

  1. Efficient Wide Range Converters (EWiRaC): A new family of high efficient AC-DC Converters

    DEFF Research Database (Denmark)

    Petersen, Lars; Andersen, Michael Andreas E.

    2006-01-01

    The performance in terms of efficiency of the existing power supplies used for PFC is very dependent on the input voltage range. The boost converter is the most commonly used PFC converter because of its simplicity and high efficiency. But, the boost converter as well as other known converters...... suffers a major penalty in efficiency when used at the low end of the voltage range (90VAC) in a universal voltage range application (90-270VAC). This paper addresses this problem by suggesting a new family of converters that effectively reduces the apparent voltage range with a factor of 2 by changing...... the converter topology according to the input voltage. This new converter type has been named: efficient wide range converter (EWiRaC). The performance of the EWiRaC is experimental verified in a universal input range (90-270VAC) application with an output voltage of 185VDC capable of 500W output power. The EWi...

  2. Comparative Analysis of Resonant Converters for Energy Storage Systems

    Directory of Open Access Journals (Sweden)

    Vuchev Stoyan

    2017-01-01

    Full Text Available The following paperwork presents a comparative analysis of multiphase resonant converters for applications in energy storage systems. Models of the examined converters are developed in the software environments of MATLAB and LTspice. Results from the simulation examination of the converters during charging of supercapacitors and rechargeable batteries are presented. These results are compared to results obtained from experimental examination of the converters via a laboratory stand. For the purposes of the experimental examination, a control system is developed on the base of a virtual instrument in LabVIEW. The advantages and disadvantages of the different converters are discussed.

  3. Three new DC-to-DC Single-Switch Converters

    Directory of Open Access Journals (Sweden)

    Barry W. Williams

    2017-06-01

    Full Text Available This paper presents a new family of three previously unidentified dc-to-dc converters, buck, boost, and buck-boost voltage-transfer-function topologies, which offer advantageous transformer coupling features and low capacitor dc voltage stressing. The three single-switch, single-diode, converters offer the same features as basic dc-to-dc converters, such as the buck function with continuous output current and the boost function with continuous input current. Converter time-domain simulations and experimental results (including transformer coupling support and extol the dc-to-dc converter concepts and analysis presented.

  4. Two phase interleaved buck converter for driving high power LEDs

    DEFF Research Database (Denmark)

    Beczkowski, Szymon; Munk-Nielsen, Stig

    2011-01-01

    The goal of this paper is to evaluate an interleaved buck topology for driving high current light-emitting diodes. Low output capacitor value allows the use of non-electrolytic capacitors extending the lifetime of the converter. Converter is operated as a constant, regulated current source which...... increases luminous efficacy of LED compared to PWM dimmed system. Because of the low dynamic resistance of LEDs the duty cycle of the converter does not change greatly with controlled current. By setting the input voltage of the buck converter to around twice the voltage of diode strings, converter can...

  5. Research on Compensating Power Converter used for Artillery

    Directory of Open Access Journals (Sweden)

    Xing Wang

    2014-11-01

    Full Text Available Aiming at the low efficiency shortage of traditional power supply converter used for artillery, a novel compensating power converter used for artillery was proposed, and its work mode was analyzed. The current expression of inductor was given and work statuses under two working modes were analyzed. Finally an experimental prototype based on DSP was built, the results indicate that the compensating power converter own low current and voltage stress and high efficiency because only part of power pass through the converter, thus, the converter own large potential application value.

  6. Three-phase Resonant DC-link Converter

    DEFF Research Database (Denmark)

    Munk-Nielsen, Stig

    The purpose of the project is to develop a three-phase resonant converter suitable for standard speed drives. The motivation for working with resonant converters is found in the problem of the standard converter type used today. In standard converter type Pulse Width Modulated-Voltage Source...... no additional power electric components is eliminating the high voltage peaks associated with the resonant circuit. The resonant link voltage peaks are limited below 2.1 times the DC link voltages. A new principle eliminating former resonant converter stability problems are proposed, implemented and tested...

  7. Converter applications and their influence on large electrical machines

    CERN Document Server

    Drubel, Oliver

    2013-01-01

    Converter driven applications are applied in more and more processes. Almost any installed wind-farm, ship drives, steel mills, several boiler feed water pumps, extruder and many other applications operate much more efficient and economic in case of variable speed solutions. The boundary conditions for a motor or generator will change, if it is supplied by a converter. An electrical machine, which is operated by a converter, can no longer be regarded as an independent component, but is embedded in a system consisting of converter and machine. This book gives an overview of existing converter designs for large electrical machines. Methods for the appropriate calculation of machine phenomena, which are implied by converters are derived in the power range above 500kVA. It is shown how due to the converter inherent higher voltage harmonics and pulse frequencies special phenomena are caused inside the machine which can be the reason for malfunction. It is demonstrated that additional losses create additional tempe...

  8. Effect of inlet cone pipe angle in catalytic converter

    Science.gov (United States)

    Amira Zainal, Nurul; Farhain Azmi, Ezzatul; Arifin Samad, Mohd

    2018-03-01

    The catalytic converter shows significant consequence to improve the performance of the vehicle start from it launched into production. Nowadays, the geometric design of the catalytic converter has become critical to avoid the behavior of backpressure in the exhaust system. The backpressure essentially reduced the performance of vehicles and increased the fuel consumption gradually. Consequently, this study aims to design various models of catalytic converter and optimize the volume of fluid flow inside the catalytic converter by changing the inlet cone pipe angles. Three different geometry angles of the inlet cone pipe of the catalytic converter were assessed. The model is simulated in Solidworks software to determine the optimum geometric design of the catalytic converter. The result showed that by decreasing the divergence angle of inlet cone pipe will upsurge the performance of the catalytic converter.

  9. Generators for gearless wind energy converters

    Energy Technology Data Exchange (ETDEWEB)

    Grauers, A. [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept. of Electric Power Engineering

    1996-12-01

    This paper discusses some design alternatives for directly driven generators, and one specific generator type is investigated for a wide range of rated power. First, the specification for a directly driven generator is presented, then different design alternatives are discussed. A radial-flux permanent magnet generator for frequency converter connection has been chosen for a more detailed investigation. The design, optimization and performance of that generator type are presented. Generators from 30 kW to 3 MW are designed and compared with conventional four-pole generators with gear. It is found that a directly driven generator can be more efficient than a conventional generator and gear and have a rather small diameter and a low active weight. 8 refs, 7 figs, 2 tabs

  10. Mechanical vibration to electrical energy converter

    Science.gov (United States)

    Kellogg, Rick Allen [Tijeras, NM; Brotz, Jay Kristoffer [Albuquerque, NM

    2009-03-03

    Electromechanical devices that generate an electrical signal in response to an external source of mechanical vibrations can operate as a sensor of vibrations and as an energy harvester for converting mechanical vibration to electrical energy. The devices incorporate a magnet that is movable through a gap in a ferromagnetic circuit, wherein a coil is wound around a portion of the ferromagnetic circuit. A flexible coupling is used to attach the magnet to a frame for providing alignment of the magnet as it moves or oscillates through the gap in the ferromagnetic circuit. The motion of the magnet can be constrained to occur within a substantially linear range of magnetostatic force that develops due to the motion of the magnet. The devices can have ferromagnetic circuits with multiple arms, an array of magnets having alternating polarity and, encompass micro-electromechanical (MEM) devices.

  11. Clustering of cycloidal wave energy converters

    Science.gov (United States)

    Siegel, Stefan G.

    2016-03-29

    A wave energy conversion system uses a pair of wave energy converters (WECs) on respective active mountings on a floating platform, so that the separation of the WECs from each other or from a central WEC can be actively adjusted according to the wavelength of incident waves. The adjustable separation facilitates operation of the system to cancel reactive forces, which may be generated during wave energy conversion. Modules on which such pairs of WECs are mounted can be assembled with one or more central WECs to form large clusters in which reactive forces and torques can be made to cancel. WECs of different sizes can be employed to facilitate cancelation of reactive forces and torques.

  12. Modular Multilevel Converters: Control and Applications

    Directory of Open Access Journals (Sweden)

    Fernando Martinez-Rodrigo

    2017-10-01

    Full Text Available This review article is mainly oriented to the control and applications of modular multilevel converters (MMC. The main topologies of the switching modules are presented, for normal operation and for the elimination of DC faults. Methods to keep the capacitor voltage balanced are included. The voltage and current modulators, that are the most internal loops of control, are detailed. Voltage control and current control schemes are included which regulate DC link voltage and reactive power. The cases of unbalanced and distorted networks are analyzed, and schemes are proposed so that MMC contribute to improve the quality of the grid in these situations. The main applications in high voltage direct current (HVDC transmission along with other medium voltage (MV and low voltage (LV applications are included. Finally, the application to offshore wind farms is specifically analyzed.

  13. Layout Optimisation of Wave Energy Converter Arrays

    Directory of Open Access Journals (Sweden)

    Pau Mercadé Ruiz

    2017-08-01

    Full Text Available This paper proposes an optimisation strategy for the layout design of wave energy converter (WEC arrays. Optimal layouts are sought so as to maximise the absorbed power given a minimum q-factor, the minimum distance between WECs, and an area of deployment. To guarantee an efficient optimisation, a four-parameter layout description is proposed. Three different optimisation algorithms are further compared in terms of performance and computational cost. These are the covariance matrix adaptation evolution strategy (CMA, a genetic algorithm (GA and the glowworm swarm optimisation (GSO algorithm. The results show slightly higher performances for the latter two algorithms; however, the first turns out to be significantly less computationally demanding.

  14. Modular Power Converters for PV Applications

    Energy Technology Data Exchange (ETDEWEB)

    Ozpineci, Burak [ORNL; Tolbert, Leon M [ORNL

    2012-05-01

    This report describes technical opportunities to serve as parts of a technological roadmap for Shoals Technologies Group in power electronics for PV applications. There are many different power converter circuits that can be used for solar inverter applications. The present applications do not take advantage of the potential for using common modules. We envision that the development of a power electronics module could enable higher reliability by being durable and flexible. Modules would have fault current limiting features and detection circuits such that they can limit the current through the module from external faults and can identify and isolate internal faults such that the remaining modules can continue to operate with only minimal disturbance to the utility or customer. Development of a reliable, efficient, low-cost, power electronics module will be a key enabling technology for harnessing more power from solar panels and enable plug and play operation. Power electronics for computer power supplies, communication equipment, and transportation have all targeted reliability and modularity as key requirements and have begun concerted efforts to replace monolithic components with collections of common smart modules. This is happening on several levels including (1) device level with intelligent control, (2) functional module level, and (3) system module. This same effort is needed in power electronics for solar applications. Development of modular units will result in standard power electronic converters that will have a lower installed and operating cost for the overall system. These units will lead to increased adaptability and flexibility of solar inverters. Incorporating autonomous fault current limiting and reconfiguration capabilities into the modules and having redundant modules will lead to a durable converter that can withstand the rigors of solar power generation for more than 30 years. Our vision for the technology roadmap is that there is no need

  15. Pseudomonas spp. convert metmyoglobin into deoxymyoglobin.

    Science.gov (United States)

    Motoyama, Michiyo; Kobayashi, Miho; Sasaki, Keisuke; Nomura, Masaru; Mitsumoto, Mitsuru

    2010-01-01

    Meat 'reddening' by bacteria was observed in chilled beef. To identify the reddening bacteria, isolates were inoculated onto beef and the changes in CIE L*a*b* values monitored. As a result, two Pseudomonas spp., including Pseudomonas fragi which is commonly observed in raw meat, were selected and identified as reddening bacteria. The reddening was coincidentally occurred with the appearance of slime, and the increase in thiobarbituric acid-reactive substances (TBARS) was simultaneously suppressed. In myoglobin-containing nutrient broth, it is shown spectroscopically that P. fragi converted metmyoglobin into deoxymyoglobin. It was concluded that the meat reddening was due to the formation of deoxymyoglobin, induced by the very-low-oxygen tension brought about by Pseudomonad's oxygen consumption: This oxygen depletion simultaneously suppressed TBARS increase.

  16. Power Generation Using Mechanical Wave Energy Converter

    Directory of Open Access Journals (Sweden)

    Srinivasan Chandrasekaran

    2012-03-01

    Full Text Available Ocean wave energy plays a significant role in meeting the growing demand of electric power. Economic, environmental, and technical advantages of wave energy set it apart from other renewable energy resources. Present study describes a newly proposed Mechanical Wave Energy Converter (MEWC that is employed to harness heave motion of floating buoy to generate power. Focus is on the conceptual development of the device, illustrating details of component level analysis. Employed methodology has many advantages such as i simple and easy fabrication; ii easy to control the operations during rough weather; and iii low failure rate during normal sea conditions. Experimental investigations carried out on the scaled model of MWEC show better performance and its capability to generate power at higher efficiency in regular wave fields. Design Failure Mode and Effect Analysis (FMEA shows rare failure rates for all components except the floating buoy.

  17. Will oscillating wave surge converters survive tsunamis?

    Directory of Open Access Journals (Sweden)

    L. O’Brien

    2015-07-01

    Full Text Available With an increasing emphasis on renewable energy resources, wave power technology is becoming one of the realistic solutions. However, the 2011 tsunami in Japan was a harsh reminder of the ferocity of the ocean. It is known that tsunamis are nearly undetectable in the open ocean but as the wave approaches the shore its energy is compressed, creating large destructive waves. The question posed here is whether an oscillating wave surge converter (OWSC could withstand the force of an incoming tsunami. Several tools are used to provide an answer: an analytical 3D model developed within the framework of linear theory, a numerical model based on the non-linear shallow water equations and empirical formulas. Numerical results show that run-up and draw-down can be amplified under some circumstances, leading to an OWSC lying on dry ground!

  18. Mining disease state converters for medical intervention of diseases.

    Science.gov (United States)

    Dong, Guozhu; Duan, Lei; Tang, Changjie

    2010-02-01

    In applications such as gene therapy and drug design, a key goal is to convert the disease state of diseased objects from an undesirable state into a desirable one. Such conversions may be achieved by changing the values of some attributes of the objects. For example, in gene therapy one may convert cancerous cells to normal ones by changing some genes' expression level from low to high or from high to low. In this paper, we define the disease state conversion problem as the discovery of disease state converters; a disease state converter is a small set of attribute value changes that may change an object's disease state from undesirable into desirable. We consider two variants of this problem: personalized disease state converter mining mines disease state converters for a given individual patient with a given disease, and universal disease state converter mining mines disease state converters for all samples with a given disease. We propose a DSCMiner algorithm to discover small and highly effective disease state converters. Since real-life medical experiments on living diseased instances are expensive and time consuming, we use classifiers trained from the datasets of given diseases to evaluate the quality of discovered converter sets. The effectiveness of a disease state converter is measured by the percentage of objects that are successfully converted from undesirable state into desirable state as deemed by state-of-the-art classifiers. We use experiments to evaluate the effectiveness of our algorithm and to show its effectiveness. We also discuss possible research directions for extensions and improvements. We note that the disease state conversion problem also has applications in customer retention, criminal rehabilitation, and company turn-around, where the goal is to convert class membership of objects whose class is an undesirable class.

  19. Grid Connected Solar PV System with SEPIC Converter Compared with Parallel Boost Converter Based MPPT

    Directory of Open Access Journals (Sweden)

    T. Ajith Bosco Raj

    2014-01-01

    Full Text Available The main objective of this work is to study the behaviour of the solar PV systems and model the efficient Grid-connected solar power system. The DC-DC MPPT circuit using chaotic pulse width modulation has been designed to track maximum power from solar PV module. The conversion efficiency of the proposed MPPT system is increased when CPWM is used as a control scheme. This paper also proposes a simplified multilevel (seven level inverter for a grid-connected photovoltaic system. The primary goal of these systems is to increase the energy injected to the grid by keeping track of the maximum power point of the panel, by reducing the switching frequency, and by providing high reliability. The maximum power has been tracked experimentally. It is compared with parallel boost converter. Also this model is based on mathematical equations and is described through an equivalent circuit including a PV source with MPPT, a diode, a series resistor, a shunt resistor, and dual boost converter with active snubber circuit. This model can extract PV power and boost by using dual boost converter with active snubber. By using this method the overall system efficiency is improved thereby reducing the switching losses and cost.

  20. Development of a test platform for controlling parallel converters

    DEFF Research Database (Denmark)

    Bede, Lorand; Kopacz, Csaba; Kerekes, Tamas

    2014-01-01

    As renewable energy contributes more and more in the power generation, bigger and more efficient power converters are used to integrate these energy sources into the power grid. Paralleling the power converters, is an accepted method to reduce the size of the passive elements and losses. By making...... a proper interleaving angle between the converters the current ripple can be reduced considerably. In order to be able to investigate the performance of these converters a safe and cheap platform is essential. The development of a test platform for such an application is challenging, since a proper...... synchronization has to be established between the converters. In this paper a universal platform is presented, which allows to parallel n converters with arbitrary interleaving angle between each other....

  1. Synchronously Driven Power Converter Controller Solution for MedAustron

    CERN Document Server

    Šepetavc, Luka; Tavčar, Rok; Moser, Roland; Gutleber, Johannes

    2011-01-01

    MedAustron is an ion beam cancer therapy and research centre currently under construction in Wiener Neustadt, Austria. This facility features a synchrotron particle accelerator for light ions. Cosylab is closely working together with MedAustron on the development of a power converter controller (PCC) for the 260 deployed power converters – power supplies. Power converters deliver power to magnets used for focusing and steering particle beams. We have designed and developed software and hardware which allows integration of different types of power converters into MedAustron's control system (MACS). PCC's role is to synchronously control and monitor connected power converters. Custom real-time fibre optics link and modular front end devices have been designed for this purpose. Modular front end devices make it possible to interface with almost any type of power converter – with or without built in regulation logic. We implemented realtime mechanisms and a dedicated real-time fibre link to ...

  2. PV source based high voltage gain current fed converter

    Science.gov (United States)

    Saha, Soumya; Poddar, Sahityika; Chimonyo, Kudzai B.; Arunkumar, G.; Elangovan, D.

    2017-11-01

    This work involves designing and simulation of a PV source based high voltage gain, current fed converter. It deals with an isolated DC-DC converter which utilizes boost converter topology. The proposed converter is capable of high voltage gain and above all have very high efficiency levels as proved by the simulation results. The project intends to produce an output of 800 V dc from a 48 V dc input. The simulation results obtained from PSIM application interface were used to analyze the performance of the proposed converter. Transformer used in the circuit steps up the voltage as well as to provide electrical isolation between the low voltage and high voltage side. Since the converter involves high switching frequency of 100 kHz, ultrafast recovery diodes are employed in the circuitry. The major application of the project is for future modeling of solar powered electric hybrid cars.

  3. Distance relay performance in future converter dominated power systems

    DEFF Research Database (Denmark)

    Sarkar, Moumita; Jia, Jundi; Yang, Guangya

    2017-01-01

    relay is major concern as miscoordination of backup relays in case of cascading faults can lead to severe stress in system, which can develop into blackout. In this paper, response of relays in traditional system is compared with response of relays in low short-circuit-current power systems. Impact...... of converter controls on fault current response of converter-based generations is also investigated. Index Terms—Converter control, distance relays, power system protection, system modelling.......Increasing penetration of converter-based generations in power system has led to new system challenges. Short circuit power response from converter-based generations is different from that of traditional synchronous generators. Power electronic converters can be designed for over-current only up...

  4. Grid Converters for Stationary Battery Energy Storage Systems

    DEFF Research Database (Denmark)

    Trintis, Ionut

    to hours, rated at MW and MWh, battery energy storage systems are suitable and ecient solutions. Grid connection of the storage system can be done at dierent voltage levels, depending on the location and application scenario. For high power and energy ratings, increase in the battery and converter voltage...... was realized for a 100 kW active rectier to be used in a 6 kV battery energy storage test bench. In the second part, dierent solutions for power converters to interface energy storage units to medium voltage grid are given. A new modular multilevel converter concept is introduced, where the energy storage......-voltage 100 kW bidirectional grid converter, to be used in a high voltage battery energy storage test bench. The control structure proved to be stable without damping. The converter was tested in the test bench and the experimental results are presented. Multilevel converters are replacing the classical two...

  5. High Voltage Bi-directional Flyback Converter for Capacitive Actuator

    DEFF Research Database (Denmark)

    Thummala, Prasanth; Zhang, Zhe; Andersen, Michael A. E.

    2013-01-01

    This paper presents a high voltage DC-DC converter topology for bi-directional energy transfer between a low voltage DC source and a high voltage capacitive load. The topology is a bi-directional flyback converter with variable switching frequency control during the charge mode, and constant...... switching frequency control during the discharge mode. The converter is capable of charging the capacitive load from 24 V DC source to 2.5 kV, and discharges it to 0 V. The flyback converter has been analyzed in detail during both charge and discharge modes, by considering all the parasitic elements...... in the converter, including the most dominating parameters of the high voltage transformer viz., self-capacitance and leakage inductance. The specific capacitive load for this converter is a dielectric electro active polymer (DEAP) actuator, which can be used as an effective replacement for conventional actuators...

  6. Serum angiotensin converting enzyme in pemphigus vulgaris

    Directory of Open Access Journals (Sweden)

    Reza M Robati

    2014-01-01

    Full Text Available Background: Pemphigus vulgaris is an autoimmune blistering skin disease with unknown etiology. Drugs such as angiotensin-converting enzyme (ACE inhibitors may contribute in the pathogenesis of pemphigus. Objective: We plan this essay to evaluate the serum ACE level in pemphigus vulgaris patients in comparison with healthy controls to recognize its possible role in disease pathogenesis or activity. Methods: This study was planned and performed in the dermatology clinics of Shahid Beheshti University of MedicalSciences′ Hospitals between July 2010 and June 2011. Patients with new onset of pemphigus vulgaris were enrolled in our study. Control subjects were frequency-matched to cases by sex and age. Serum ACE was determined by the spectrophotometric method. Results: Thirty-four patients with pemphigus vulgaris and 35 healthy individuals were recruited in the study. No statistical significant difference was detected in the mean level of serum ACE of the two groups (t-test, P = 0.11. The mean ACE level was significantly lower in male patients compared with male controls (P = 0.04. Moreover, a significant higher serum ACE level of patients with cutaneous involvement was observed compared to patients with mucosal involvement (P = 0.02. Conclusions: Despite lack of any significant difference of serum ACE level between pemphigus and control group, the serum ACE level was considerably lower in male pemphigus vulgaris patients compared with male controls. Therefore, ACE might have some association with pemphigus vulgaris especially in male patients; however, further studies are required to confirm this association.

  7. Radiolabelled substrates for angiotensin converting enzyme

    International Nuclear Information System (INIS)

    Chung, A.Y.; Ryan, J.W.; Ryan, J.P.; Ryan, U.S.

    1986-01-01

    Six [3H]benzoyl-tripeptides were prepared and tested as substrates for angiotensin converting enzyme. Each was prepared first as its [4-iodo]-benzoyl-analog, and an atom of 3H per molecule was introduced by catalytic dehalogenation in 3H2-gas. Kinetic parameters were measured at 37 degrees C using as buffer 0.05 M Hepes, pH 8.0 containing 0.1 M NaCl and 0.6 M Na2SO4. When the substrates were used at concentrations far below their respective Km values, fractional rates of substrate utilization per unit time for constant enzyme concentration were direct function of respective second order rate constants (Kc/Km). Although absolute values of Kc/Km differed for human enzyme as opposed to rabbit enzyme, relative values of Kc/Km were virtually identical. Similarly, relative rates of substrates utilization during passage through lungs of anesthetized rats were similar to relative values of Kc/Km measured in vitro. Thus, there is now a range of ACE substrates usable, in vitro and in vivo, under conditions of first order enzyme kinetics, conditions under which values of V/Km and Ki can be measured directly

  8. Structural Loads Analysis for Wave Energy Converters

    Energy Technology Data Exchange (ETDEWEB)

    van Rij, Jennifer A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Yu, Yi-Hsiang [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Guo, Yi [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-06-03

    This study explores and verifies the generalized body-modes method for evaluating the structural loads on a wave energy converter (WEC). Historically, WEC design methodologies have focused primarily on accurately evaluating hydrodynamic loads, while methodologies for evaluating structural loads have yet to be fully considered and incorporated into the WEC design process. As wave energy technologies continue to advance, however, it has become increasingly evident that an accurate evaluation of the structural loads will enable an optimized structural design, as well as the potential utilization of composites and flexible materials, and hence reduce WEC costs. Although there are many computational fluid dynamics, structural analyses and fluid-structure-interaction (FSI) codes available, the application of these codes is typically too computationally intensive to be practical in the early stages of the WEC design process. The generalized body-modes method, however, is a reduced order, linearized, frequency-domain FSI approach, performed in conjunction with the linear hydrodynamic analysis, with computation times that could realistically be incorporated into the WEC design process.

  9. Image processing to optimize wave energy converters

    Science.gov (United States)

    Bailey, Kyle Marc-Anthony

    The world is turning to renewable energies as a means of ensuring the planet's future and well-being. There have been a few attempts in the past to utilize wave power as a means of generating electricity through the use of Wave Energy Converters (WEC), but only recently are they becoming a focal point in the renewable energy field. Over the past few years there has been a global drive to advance the efficiency of WEC. Placing a mechanical device either onshore or offshore that captures the energy within ocean surface waves to drive a mechanical device is how wave power is produced. This paper seeks to provide a novel and innovative way to estimate ocean wave frequency through the use of image processing. This will be achieved by applying a complex modulated lapped orthogonal transform filter bank to satellite images of ocean waves. The complex modulated lapped orthogonal transform filterbank provides an equal subband decomposition of the Nyquist bounded discrete time Fourier Transform spectrum. The maximum energy of the 2D complex modulated lapped transform subband is used to determine the horizontal and vertical frequency, which subsequently can be used to determine the wave frequency in the direction of the WEC by a simple trigonometric scaling. The robustness of the proposed method is provided by the applications to simulated and real satellite images where the frequency is known.

  10. Do selvagem convertível

    Directory of Open Access Journals (Sweden)

    Andréa Daher

    Full Text Available A atitude de tolerância frente à alteridade indígena e a representação do índio tupinambá docilmente "convertível" contidas no relato do capuchinho Claude d'Abbeville,Histoire de la Mission... en l'isle de Maragnan (1614, são claramente tributárias do livro do huguenote Jean de Léry,Histoire d'un voyage fait en la terre du Brésil (1578. O capuchinho parafraseia o huguenote em várias passagens, mostrando o índio como objeto de análise "etnográfica", sem excluí-lo - como faz Léry - da possibilidade de salvação. Provavelmente, Claude d'Abbeville responde, desta forma, às expectativas do público francês, num contexto de exortação à colonização do Maranhão e de propaganda da obra apostólica da Ordem dos Capuchinhos.

  11. Power Converters Maximize Outputs Of Solar Cell Strings

    Science.gov (United States)

    Frederick, Martin E.; Jermakian, Joel B.

    1993-01-01

    Microprocessor-controlled dc-to-dc power converters devised to maximize power transferred from solar photovoltaic strings to storage batteries and other electrical loads. Converters help in utilizing large solar photovoltaic arrays most effectively with respect to cost, size, and weight. Main points of invention are: single controller used to control and optimize any number of "dumb" tracker units and strings independently; power maximized out of converters; and controller in system is microprocessor.

  12. A SOFT SWITCHED INTERLEAVED HIGH GAIN DC-DC CONVERTER

    Directory of Open Access Journals (Sweden)

    SHESHIDHAR REDDY ADDULA

    2017-09-01

    Full Text Available In this paper, a novel soft-switched interleaved DC-DC converter which provides a high voltage gain of 12 is proposed. Voltage gain of the basic interleaved boost converter is extended by using diode-capacitor multiplier (DCM cells. The switches are operated at a nominal duty ratio of 0.5. The voltage stress on the power switches and diodes is only a fraction of the output voltage. To enhance the operating power conversion efficiency, the switches are turned ON at zero voltage condition. Experimental results of 18-216V, 100W prototype converter validate the operating principle and the advantageous features of the presented converter.

  13. Analysis and Design of Embedded Controlled Parallel Resonant Converter

    Directory of Open Access Journals (Sweden)

    P. CHANDRASEKHAR

    2009-07-01

    Full Text Available Microcontroller based constant frequency controlled full bridge LC parallel resonant converter is presented in this paper for electrolyser application. An electrolyser is a part of renewable energy system which generates hydrogen from water electrolysis. The DC power required by the electrolyser system is supplied by the DC-DC converter. Owing to operation under constant frequency, the filter designs are simplified and utilization of magnetic components is improved. This converter has advantages like high power density, low EMI and reduced switching stresses. DC-DC converter system is simulated using MATLAB, Simulink. Detailed simulation results are presented. The simulation results are compared with the experimental results.

  14. Number-to-voltage converter on commutated condensers

    International Nuclear Information System (INIS)

    Grekhov, Yu.N.

    1975-01-01

    A code-voltage converter using precision voltage dividers based on commutated capacitors [1] is described which is distinguished by the absence of precision elements. Each digit includes eight field-effect transistors in two 1KT682 microcircuit assemblies and three microcapacitors with a conventional unstable capacitance 6200 pF +- 50%. The converter has a speed of response that is not inferior to that of converters based on R-2R matrices, while in time stability of the characteristics, low interference level, and low output impedance it is superior to such converters

  15. High Efficiency Hall Thruster Discharge Power Converter Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Busek leveraged previous, internally sponsored, high power, Hall thruster discharge converter development which allowed it to design, build, and test new printed...

  16. A new configuration for multilevel converters with diode clamped topology

    DEFF Research Database (Denmark)

    Nami, A.; Zare, F.; Ledwich, G.

    2008-01-01

    Due to the increased use of renewable energy and power elctronic applications, more multilevel converters (MLC) are developed. A Neutral Point Clamped (NPC) inverter is one of the most used multilevel topologies for wind turbine (WT) and photovoltaic (PV) applications. One of the most crucial...... points in this type of converter is dc-voltage control. In this paper, a novel multi output dc-dc converter connected to a diode clamped topology is presented. This converter, for a given duty cycles, is able to regulate the capacitor voltage to provide an appropriate input voltage for NPC regardless...

  17. Development of a wind converter and investigation of its operational function. Part 1: Technical description of the wind energy converter

    Science.gov (United States)

    Molly, J. P.; Steinheber, R.

    1982-11-01

    A 10 kW wind energy converter was developed by using as far possible standard serial production parts. The design criteria and the description of the essential machinery components of the MODA 10 wind energy converter are discussed. For some special load cases the safety calculation of the important components is shown. The blade control system which qualified for small wind energy converters, is explained. Weight and cost of the MODA 10 are considered.

  18. Converting hard copy documents for electronic dissemination

    Energy Technology Data Exchange (ETDEWEB)

    Hoffman, F.

    1994-12-31

    Since the advent of computer systems, the goal of a paperless office, and even a paperless society, has been pursued. While the normal paper flow in an organization is far from totally automated, particularly for items requiring signatures or authorizations, electronic information dissemination is becoming an almost simple task. The reasons for providing on-line documents are many and include faster and easier access for everyone, elimination of printing costs, reduction of wasted shelf and desk space, and the security of having a centrally-located, always up-to-date document. New computer software even provides the user with the ability to annotate documents and to have bookmarks so that the old scribbled-in and dog-eared manual can be replaced without loosing this `customizability`. Moreover, new hypermedia capabilities mean that documents can be read in a non-linear fashion and can include color figures and photographs, audio, and even animation sequences, capabilities which exceed those of paper. The proliferation of network-based information servers, coupled with the growth of the Internet, has enticed academic, governmental, and even commercial organizations to provide increasing numbers of documents and data bases in electronic form via the network, not just to internal staff, but to the public as well. Much of this information, which includes everything from mundane company procedures to spiffy marketing brochures, was previously published only in hard copy. Converting existing documents to electronic form and producing only electronic versions of new documents poses some interesting challenges to the maintainer or author.

  19. A New Perspective for Modeling Power Electronics Converters : Complementarity Framework

    NARCIS (Netherlands)

    Vasca, Francesco; Iannelli, Luigi; Camlibel, M. Kanat; Frasca, Roberto

    2009-01-01

    The switching behavior of power converters with "ideal" electronic devices (EDs) makes it difficult to define a switched model that describes the dynamics of the converter in all possible operating conditions, i.e., a "complete" model. Indeed, simplifying assumptions on the sequences of modes are

  20. Converting Geometry from Creo Parametric to BRL-CAD

    Science.gov (United States)

    2017-06-28

    ARL-SR-0376 ● JUNE 2017 US Army Research Laboratory Converting Geometry from Creo Parametric to BRL- CAD by Clifford W Yapp...to the originator. ARL-SR-0376 ● JUNE 2017 US Army Research Laboratory Converting Geometry from Creo Parametric to BRL- CAD by...

  1. Development of custom radiation-tolerant DCDC converter ASICs

    CERN Document Server

    Faccio, F; Michelis, S; Saggini, S; Fuentes, C; Ongaro, F; Orlandi, S

    2010-01-01

    Based on a detailed study of the radiation tolerance of high-voltage transistors, 2 commercial CMOS technologies have been selected for the design of synchronous buck DCDC converter ASICs. Three prototype converters have been produced, embedding increasingly sophisticated functions. The electrical and radiation performance of these prototypes is presented.

  2. Digital parallel-to-series pulse-train converter

    Science.gov (United States)

    Hussey, J.

    1971-01-01

    Circuit converts number represented as two level signal on n-bit lines to series of pulses on one of two lines, depending on sign of number. Converter accepts parallel binary input data and produces number of output pulses equal to number represented by input data.

  3. Modeling and simulation of matrix converter for wind power generation

    International Nuclear Information System (INIS)

    Masood, F.; Mahmood, T.; Choudhry, M.A.

    2013-01-01

    In this paper, a matrix converter structure is proposed which is suitable for wind power generation applications. The matrix converter (MC) is the most general converter type in the family of AC-AC converters. It is a single-stage converter which has an array of m x n bidirectional power switches to connect, directly, an m- phase voltage source to an n-Phase load. It does not have any DC-link circuit and does not need any large energy storage elements. The key element in a matrix converter is the fully controlled four quadrant bidirectional switch, which allows highfrequency operation. The proposed converter uses MOSFETs as bidirectional switches. The model has been implemented using MATLAB/SIMULINK. The results obtained are presented. The waveforms for input current and output voltage are sinusoidal with very low total harmonic distortion (THD). Low THD is an indication that the model is suitable for wind power generation applications. The simulation results confirm the reduction of conversion losses by 10% to 12% as compared to conventional two stage converters thereby increasing the overall conversion efficiency. The MOSFETs which have been used as switching devices have four to five times more switching frequency as compared to IGBTs thus improving the resulting wave shapes. (author)

  4. Multifunctional Converter Drive for Automotive Electric Power Steering Systems

    NARCIS (Netherlands)

    Hackner, T.J.

    2013-01-01

    In this thesis it is shown that in the case of an automotive electric power steering system, critical pulse power loads can be decoupled from the power net with a storage element and a multifunctional converter. A multifunctional converter system is proposed because it uses the motor drive system as

  5. Utilization of non-linear converters for audio amplification

    DEFF Research Database (Denmark)

    Iversen, Niels Elkjær; Birch, Thomas; Knott, Arnold

    2012-01-01

    . The introduction of non-linear converters for audio amplification defeats this limitation. A Cuk converter, designed to deliver an AC peak output voltage twice the supply voltage, is presented in this paper. A 3V prototype has been developed to prove the concept. The prototype shows that it is possible to achieve...

  6. Wave Dragon Wave Energy Converters Used as Coastal Protection

    DEFF Research Database (Denmark)

    Nørgaard, Jørgen Harck; Andersen, Thomas Lykke; Kofoed, Jens Peter

    2011-01-01

    This paper deals with wave energy converters used to reduce the wave height along shorelines. For this study the Wave Dragon wave energy converter is chosen. The wave height reduction from a single device has been evaluated from physical model tests in scale 1:51.8 of the 260 x 150 m, 24 kW/m mod...

  7. Converted Firearms: A Transnational Problem with Local Harm

    NARCIS (Netherlands)

    de Vries, Marsha

    2012-01-01

    Over the last decade, the Dutch police as well as police forces in several other Western-European countries were confronted with an increase in the availability and use of converted firearms. Converted firearms were originally blank firing weapons, for example gas and alarm pistols, which are

  8. A CMOS rail-to-rail linear VI-converter

    NARCIS (Netherlands)

    Vervoort, P.P.; Vervoort, P.P.; Wassenaar, R.F.

    1995-01-01

    A linear CMOS VI-converter operating in strong inversion with a common-mode input range from the negative to the positive supply rail is presented. The circuit consists of three linear VI-converters based on the difference of squares principle. Two of these perform the actual V to I conversion,

  9. Isolated step-down DC -DC converter for electric vehicles

    Science.gov (United States)

    Kukovinets, O. V.; Sidorov, K. M.; Yutt, V. E.

    2018-02-01

    Modern motor-vehicle industrial sector is moving rapidly now towards the electricity-driving cars production, improving their range and efficiency of components, and in particular the step-down DC/DC converter to supply the onboard circuit 12/24V of electric vehicle from the high-voltage battery. The purpose of this article - to identify the best circuitry topology to design an advanced step-down DC/DC converters with the smallest mass, volume, highest efficiency and power. And this will have a positive effect on driving distance of electric vehicle (EV). On the basis of computational research of existing and implemented circuit topologies of step-down DC/DC converters (serial resonant converter, full bridge with phase-shifting converter, LLC resonant converter) a comprehensive analysis was carried out on the following characteristics: specific volume, specific weight, power, efficiency. The data obtained was the basis for the best technical option - LLC resonant converter. The results can serve as a guide material in the process of components design of the traction equipment for electric vehicles, providing for the best technical solutions in the design and manufacturing of converting equipment, self-contained power supply systems and advanced driver assistance systems.

  10. Power factor correction (PFC) converters feeding brushless DC ...

    African Journals Online (AJOL)

    This paper presents a comprehensive study of power factor correction (PFC) converters for feeding brushless DC (BLDC) motor drive. This work explores various configurations of PFC converters which are classified into five different categories of non-isolated, bridgeless (BL) non-isolated, isolated, BL-isolated PFC ...

  11. A THREE-PHASE BOOST DC-AC CONVERTER

    African Journals Online (AJOL)

    - strate the feasibility of the proposed three-phase inverter. The inverter is intended to be used in three-phase electric drives and uninterruptible power supply (UPS) systems. Keywords: Boost converter, three-phase dc-ac converter, sliding ...

  12. Hydraulic Evaluation of the Crest Wing Wave Energy Converter

    DEFF Research Database (Denmark)

    Kofoed, Jens Peter; Antonishen, Michael Patrick

    This report presents the results of an experimental study of the wave energy converting abilities of the Crest Wing wave energy converter (WEC). The Crest Wing is a WEC that uses its movement in matching the shape of an oncoming wave to generate power. Model tests have been performed using a scal...

  13. Four-quadrant flyback converter for direct audio power amplification

    DEFF Research Database (Denmark)

    Ljusev, Petar; Andersen, Michael Andreas E.

    2005-01-01

    This paper presents a bidirectional, four-quadrant flyback converter for use in direct audio power amplification. When compared to the standard Class-D switching audio power amplifier with a separate power supply, the proposed four-quadrant flyback converter provides simple solution with better...

  14. Digital Carrier Modulation and Sampling Issues of Matrix Converters

    DEFF Research Database (Denmark)

    Loh, Poh Chiang; Rong, Runjie; Blaabjerg, Frede

    2009-01-01

    Although the modulation of ac-ac matrix converters using space vector theory has long been established, their carrierbased modulation principles have only recently attracted some attention. Reasons commonly stated for evaluating the carrier-based alternative include simpler converter control beca...

  15. Engineering development testing of the GPHS-RTG converter

    International Nuclear Information System (INIS)

    Cockfield, R.D.

    1981-01-01

    The GPHS-RTG will provide electrical power for the Galileo orbiter and for the two spacecraft of the International Solar Polar Mission. The GPHS-RTG consists of two primary assemblies: the General Purpose Heat Source, and the converter. This paper deals only with the converter, and highlights engineering tests that provide support for its design development

  16. Power factor correction (PFC) converters feeding brushless DC ...

    African Journals Online (AJOL)

    DR OKE

    1. Introduction. In recent trends, energy efficiency has become an important aspect of an electrical drive system due to the scarcity of the energy resources. The selection of a motor for a .... trade-off between the extra cost associated with extra sensing and permitted stress on PFC converter switch. These PFC converters can ...

  17. Primary Parallel Isolated Boost Converter with Bidirectional Operation

    DEFF Research Database (Denmark)

    Hernandez Botella, Juan Carlos; Mira Albert, Maria del Carmen; Sen, Gökhan

    2012-01-01

    This paper presents a bidirectional dc/dc converter operated with batteries both in the input and output. Primary parallel isolated boost converter (PPIBC) with transformer series connection on the high voltage side is preferred due to its ability to handle high currents in the low voltage side...

  18. Integrating data converters for picoampere currents from electrochemical transducers

    DEFF Research Database (Denmark)

    Breten, Madalina; Lehmann, Torsten; Bruun, Erik

    2000-01-01

    . A prototype chip using the dual slope conversion method has been fabricated in a 0.7 μm CMOS process. Experimental results from this converter are reported. Design problems and limitations of the converter are discussed and a new conversion technique providing a larger dynamic range and easy calibration...

  19. Platinum recovery from used auto catalytic converters in electrorefining process

    Directory of Open Access Journals (Sweden)

    A. Fornalczyk

    2013-04-01

    Full Text Available This paper presents possibility of removing platinum from the used catalytic converters applying copper as a metal collector in pyrometallurgical methods. The catalytic converter carrier was grinded and melted with copper. During the research obtained Cu-Pt alloy was casted as an anode. Such anode was electrically refined in order to recover platinum. Obtained results were discussed.

  20. Optimizing design of converters using power cycling lifetime models

    DEFF Research Database (Denmark)

    Nielsen, Rasmus Ørndrup; Munk-Nielsen, Stig

    2015-01-01

    Converter power cycling lifetime depends heavily on converter operation point. A lifetime model of a single power module switched mode power supply with wide input voltage range is shown. A lifetime model is created using a power loss model, a thermal model and a model for power cycling capability...

  1. A Signal-Interleaving Complex Bandpass Sigma-Delta Converter

    DEFF Research Database (Denmark)

    Wad, Paul Emmanuel

    1997-01-01

    Complex or quadrature Sigma-Delta converters operate on complex signals, i.e. signals consisting of a real and an imaginary component, whereas conventional converters operate only on real signals. The advantage of complex signal processing in the discrete-time domain is that the entire sampling...

  2. A Level Converter provided with Slew-Rate Controlling Means

    NARCIS (Netherlands)

    Annema, Anne J.

    2000-01-01

    A level converter for the converting of a first digital signal (U1) having a first voltage range into a second digital signal (U2) having a second voltage range comprising an amplifier (T0) having an input for receiving the first digital signal (U1) and an output for supplying the second digital

  3. Design of an emi output filter for frequency converters

    NARCIS (Netherlands)

    Roc'h, A.; Bergsma, J.G.; Bergsma, H.; Leferink, Frank Bernardus Johannes; Zhao, D.; Polinder, H.; Ferreira, B.

    2006-01-01

    A filter has been designed to reduce conducted and radiated emission generated by a frequency converter. The frequency converter, cables and motor were modelled in order to make a good estimation of the radiated emission. A single stage output filter was designed making use of feedthrough apacitors

  4. Pilot tones in WDM networks with wavelength converters

    DEFF Research Database (Denmark)

    Kloch, Allan; Mikkelsen, Benny; Stubkjær, Kristian

    1997-01-01

    Here we investigate the transmission of a pilot tone through an interferometric wavelength converter (IWC) in conjunction with a 2.5 Gbit/s experiment. The pilot tone is added by sinusoidal modulation of the bias current to the signal laser. After the IWC (Michelson interferometer) the converted...

  5. Very High Frequency Half Bridge DC/DC Converter

    DEFF Research Database (Denmark)

    Madsen, Mickey Pierre; Knott, Arnold; Andersen, Michael A. E.

    2014-01-01

    This paper presents the first, off chip, class DE (resonant half bridge) converter working in the Very High Frequency (VHF) range. The benefits of using half bridge circuits both in the inverter and rectifier part of a VHF resonant dc/dc converter are analyzed and design equations for all...

  6. Charge pump DC-DC converter comprising solid state batteries

    NARCIS (Netherlands)

    Reefman, D.; Roozeboom, F.; Notten, P.H.L.; Klootwijk, J.H.

    2013-01-01

    An electronic device is provided which comprises a DC-DC converter. The DC-DC converter comprises at least one solid-state rechargeable battery (B1, B2) for storing energy for the DC-DC conversion and an output capacitor (C2).

  7. Estimation of reliability of a interleaving PFC boost converter

    Directory of Open Access Journals (Sweden)

    Gulam Amer Sandepudi

    2010-01-01

    Full Text Available Reliability plays an important role in power supplies. For other electronic equipment, a certain failure mode, at least for a part of the total system, can often be employed without serious (critical effects. However, for power supply no such condition can be accepted, since very high demands on its reliability must be achieved. At higher power levels, the continuous conduction mode (CCM boost converter is preferred topology for implementation a front end with PFC. As a result, significant efforts have been made to improve the performance of high boost converter. This paper is one of the efforts for improving the performance of the converter from the reliability point of view. In this paper, interleaving boost power factor correction converter is simulated with single switch in continuous conduction mode (CCM, discontinuous conduction mode (DCM and critical conduction mode (CRM under different output power ratings. Results of the converter are explored from reliability point of view.

  8. CAS CERN Accelerator School: Power converters for particle accelerators

    International Nuclear Information System (INIS)

    Turner, S.

    1990-01-01

    This volume presents the proceedings of the fifth specialized course organized by the CERN Accelerator School, the subject on this occasion being power converters for particle accelerators. The course started with lectures on the classification and topologies of converters and on the guidelines for achieving high performance. It then went on to cover the more detailed aspects of feedback theory, simulation, measurements, components, remote control, fault diagnosis and equipment protection as well as systems and grid-related problems. The important topics of converter specification, procurement contract management and the likely future developments in semiconductor components were also covered. Although the course was principally directed towards DC and slow-pulsed supplies, lectures were added on fast converters and resonant excitation. Finally the programme was rounded off with three seminars on the related fields of Tokamak converters, battery energy storage for electric vehicles, and the control of shaft generators in ships. (orig.)

  9. An Innovative Reconfigurable Integrated Converter Topology Suitable for Distributed Generation

    Directory of Open Access Journals (Sweden)

    Renato Rizzo

    2012-09-01

    Full Text Available The electricity market and environmental concerns, with wide utilization of renewable sources, have improved the diffusion of distributed generation units changing the operations of distribution grids from passive networks to microgrids. A microgrid includes a cluster of electrical loads, energy storage devices and microsources, which provide both power and heat to their local area. A microgrid has usually one connection point to the utility grid through power electronic converters placed at customers’ sites. This paper analyses a Reconfigurable Integrated Converter (RIC used for a domestic microgrid with inputs from the AC mains and photovoltaic arrays, and two DC outputs at different voltage levels. A RIC as a dual-boost DC-DC converter is proposed, modelled and analysed in the paper. The advantages of such a topology in comparison with traditional boost converters are outlined. Reported simulations results give evidence on the controllability of this converter and the capability of achieving the desired voltage outputs with reduced ripple.

  10. TOPOLOGICAL REVIEW AND ANALYSIS OF DC-DC BOOST CONVERTERS

    Directory of Open Access Journals (Sweden)

    V. INDRA GANDHI

    2017-06-01

    Full Text Available DC voltage boost up is essential in numerous applications; especially considering Photovoltaic (PV based renewable power generation system. The conventional DC-DC boost converter is the most admired configuration for this scheme, even if the converter efficiency is restricted at duty cycle near to maximum value. In order to find solution to the problem and improve its conversion capability, many converter configurations have been implemented so far. With this circumstance, this research work proposes to give overview of a few most imperative research works related to DC-DC boost converters. Some configurations are covered and classified basically based on the application. The major benefits and disadvantages related to the available techniques are also briefly conveyed. At last, a proper evaluation is recognized among the important types of DC-DC boost converters in terms of efficiency, number of components, and stability.

  11. The New Modular Control System for Power Converters at CERN

    CERN Document Server

    Di Cosmo, Matteo

    2015-01-01

    The CERN accelerator complex consists of several generations of particle accelerators, with around 5000 power converters supplying regulated current and voltage to normal and superconducting magnet circuits. Today around 12 generations of converter control platforms can be found in the accelerator complex, ranging in age and technology. The diversity of these platforms has a significant impact on operability, maintenance and support of power converters. Over the past few years a new generation of modular controls called RegFGC3 has been developed by CERN’s power conversion group, with a goal to provide a standardised control platform, supporting a wide variety of converter topologies. The aim of this project is to reduce maintenance costs by decreasing the variety and diversity of control systems whilst simultaneously improving the operability and reliability of power converters and their controls. This paper describes the state of the on-going design and realization of the RegFGC3 platform, focusing on fun...

  12. Optimization Control of Bidirectional Cascaded DC-AC Converter Systems

    DEFF Research Database (Denmark)

    Tian, Yanjun

    in bidirectional cascaded converter. This research work analyses the control strategies based on the topology of dual active bridges converter cascaded with a three phase inverter. It firstly proposed a dc link voltage and active power coordinative control method for this cascaded topology, and it can reduce dc....... The connections of the renewable energy sources to the power system are mostly through the power electronic converters. Moreover, for high controllability and flexibility, power electronic devices are gradually acting as the interface between different networks in power systems, promoting conventional power...... the bidirectional power flow in the distribution level of power systems. Therefore direct contact of converters introduces significant uncertainties to power system, especially for the stability and reliability. This dissertation studies the optimization control of the two stages directly connected converters...

  13. High Speed Level Converters With Short Circuit Current Reduction

    Directory of Open Access Journals (Sweden)

    Avireni Srinivasulu

    2014-08-01

    Full Text Available The level converter is used as interface between low voltages to high voltage boundary. The efficient level converter has less power consumption and less delay are the design considerations of the level shifter. In this paper two new CMOS level converters are presented with high driving capability with low propagation delay. The proposed level converters are simulated using Cadence software with 0.18 µm CMOS technology. The simulation result shows that the proposed circuits have less propagation delay than the existing ones. The circuits are simulated for different load capacitor values and different voltages. The proposed level converters operate for different input pulse signal amplitude values are +0.8 V, +1 V, +1.2 V and VDDH values of +1.8 V and +3.3 V.

  14. Broadband tunable terahertz polarization converter based on graphene metamaterial

    Science.gov (United States)

    Luo, Shiwen; Li, Bin; Yu, Anlan; Gao, Jun; Wang, Xinbing; Zuo, Duluo

    2018-04-01

    We design and numerically investigate a broadband tunable terahertz polarization converter based on graphene metamaterial. The converter presents a broad conversion band with high polarization conversion ratio (>0.95) in terahertz frequency over a bandwidth which is 25.8% of the central frequency. The converter can be dynamically tuned by varying the Fermi Energy of the graphene without changing the geometric structure. The converter shows high conversion ratio for a wide range of incident angles from 0 to 40°. By the scaling of the proposed structure, the broadband properties of the converter can be easily spread to other frequency. The proposed metamaterial offers an approach in the manipulation of the light polarization and has potential applications in imaging, sensing and communications.

  15. Optimisation Of a Magnetostrictive Wave Energy Converter

    Science.gov (United States)

    Mundon, T. R.; Nair, B.

    2014-12-01

    Oscilla Power, Inc. (OPI) is developing a patented magnetostrictive wave energy converter aimed at reducing the cost of grid-scale electricity from ocean waves. Designed to operate cost-effectively across a wide range of wave conditions, this will be the first use of reverse magnetostriction for large-scale energy production. The device architecture is a straightforward two-body, point absorbing system that has been studied at length by various researchers. A large surface float is anchored to a submerged heave (reaction) plate by multiple taut tethers that are largely made up of discrete, robust power takeoff modules that house the magnetostrictive generators. The unique generators developed by OPI utilize the phenomenon of reverse magnetostriction, which through the application of load to a specific low cost alloy, can generate significant magnetic flux changes, and thus create power through electromagnetic induction. Unlike traditional generators, the mode of operation is low-displacement, high-force, high damping which in combination with the specific multi-tether configuration creates some unique effects and interesting optimization challenges. Using an empirical approach with a combination of numerical tools, such as ORCAFLEX, and physical models, we investigated the properties and sensitivities of this system arrangement, including various heave plate geometries, with the overall goal of identifying the mass and hydrodynamic parameters required for optimum performance. Furthermore, through a detailed physical model test program at the University of New Hampshire, we were able to study in more detail how the heave plate geometry affects the drag and added mass coefficients. In presenting this work we will discuss how alternate geometries could be used to optimize the hydrodynamic parameters of the heave plate, allowing maximum inertial forces in operational conditions, while simultaneously minimizing the forces generated in extreme waves. This presentation

  16. A Model Predictive Control-Based Power Converter System for Oscillating Water Column Wave Energy Converters

    Directory of Open Access Journals (Sweden)

    Gimara Rajapakse

    2017-10-01

    Full Text Available Despite the predictability and availability at large scale, wave energy conversion (WEC has still not become a mainstream renewable energy technology. One of the main reasons is the large variations in the extracted power which could lead to instabilities in the power grid. In addition, maintaining the speed of the turbine within optimal range under changing wave conditions is another control challenge, especially in oscillating water column (OWC type WEC systems. As a solution to the first issue, this paper proposes the direct connection of a battery bank into the dc-link of the back-to-back power converter system, thereby smoothening the power delivered to the grid. For the second issue, model predictive controllers (MPCs are developed for the rectifier and the inverter of the back-to-back converter system aiming to maintain the turbine speed within its optimum range. In addition, MPC controllers are designed to control the battery current as well, in both charging and discharging conditions. Operations of the proposed battery direct integration scheme and control solutions are verified through computer simulations. Simulation results show that the proposed integrated energy storage and control solutions are capable of delivering smooth power to the grid while maintaining the turbine speed within its optimum range under varying wave conditions.

  17. A Low-Voltage Switched-Capacitor Digital-to-Analog Converter Converted from Least Significant Bit

    OpenAIRE

    大野, 憲司; 松本, 寛樹; 村尾, 健次

    2010-01-01

    In this paper, it is presented that a Low-Voltage Switched-Capacitor Digital-to-Analog Converter converted from low bit. The proposed circuit can operate using simple nonoverlapping three phase clocks. It consists of a switch, capacitor, MOSFET and op-amp. Circuit operation is evaluated by PSpice.

  18. Novel family of quasi-Z-source DC/DC converters derived from current-fed push-pull converters

    DEFF Research Database (Denmark)

    Chub, Andrii; Husev, Oleksandr; Vinnikov, Dmitri

    2014-01-01

    This paper is devoted to the step-up quasi-Z-source dc/dc push-pull converter family. The topologies in the family are derived from the isolated boost converter family by replacing input inductors with the quasi-Z-source network. Two new topologies are proposed, analyzed and compared. Theoretical...

  19. Decimal multiplication using compressor based-BCD to binary converter

    Directory of Open Access Journals (Sweden)

    Sasidhar Mukkamala

    2018-02-01

    Full Text Available The objective of this work is to implement a scalable decimal to binary converter from 8 to 64 bits (i.e 2-digit to 16-digit using parallel architecture. The proposed converters, along with binary coded decimal (BCD adder and binary to BCD converters, are used in parallel implementation of Urdhva Triyakbhyam (UT-based 32-bit BCD multiplier. To increase the performance, compressor circuits were used in converters and multiplier. The designed hardware circuits were verified by behavioural and post layout simulations. The implementation was carried out using Virtex-6 Field Programmable Gate Array (FPGA and Application Specific Integrated Circuit (ASIC with 90-nm technology library platforms. The results on FPGA shows that compressor based converters and multipliers produced less amount of propagation delay with a slight increase of hardware resources. In case of ASIC implementation, a compressor based converter delay is equivalent to conventional converter with a slight increase of gate count. However, the reduction of delay is evident in case of compressor based multiplier.

  20. A new method of converter transformer protection without commutation failure

    Science.gov (United States)

    Zhang, Jiayu; Kong, Bo; Liu, Mingchang; Zhang, Jun; Guo, Jianhong; Jing, Xu

    2018-01-01

    With the development of AC / DC hybrid transmission technology, converter transformer as nodes of AC and DC conversion of HVDC transmission technology, its reliable safe and stable operation plays an important role in the DC transmission. As a common problem of DC transmission, commutation failure poses a serious threat to the safe and stable operation of power grid. According to the commutation relation between the AC bus voltage of converter station and the output DC voltage of converter, the generalized transformation ratio is defined, and a new method of converter transformer protection based on generalized transformation ratio is put forward. The method uses generalized ratio to realize the on-line monitoring of the fault or abnormal commutation components, and the use of valve side of converter transformer bushing CT current characteristics of converter transformer fault accurately, and is not influenced by the presence of commutation failure. Through the fault analysis and EMTDC/PSCAD simulation, the protection can be operated correctly under the condition of various faults of the converter.

  1. A prototype ASIC buck converter for LHC upgrades

    CERN Document Server

    Michelis, S; Allongue, B; Blanchot, G; Fuentes, C; Kayal, M

    2008-01-01

    Given the larger number of channels and the need for reduced material budget in the SLHC trackers, alternatives to the present power distribution scheme have to be explored. In this context we are envisaging a new architecture based on custom switching converters able to work in the high radiation and high magnetic field environment of the experiments. A prototype converter has been designed and integrated in an ASIC. This includes the fundamental building blocks of a buck converter that can be used in later and more complete designs and even in different topologies. Design techniques and functional tests of the prototype will be discussed.

  2. Dual charge-to-digital converter type CAMAC 715

    International Nuclear Information System (INIS)

    Kreciejewski, M.; Kulka, Z.

    1986-05-01

    A dual two input 10 bit resolution charge-to-digital converter type 715 is described. It enables digital measurement of charges carried by nanosecond current pulses from two ionizing radiation detectors. Input current pulses are first gated by high-speed linear gates and then are integrated. Resulting amplitudes of voltage pulses are converted with use of Wilkinson rundown technique. A principle of operation as well as a design and performance of charge digitizer are described. The 715 converter is intended mainly for digital n-γ pulse shape discrimination. 8 refs., 4 figs. (author)

  3. A DSP controlled one-to-three phase matrix converter

    Energy Technology Data Exchange (ETDEWEB)

    Dubovsky, J.; Dobrucly, B; Tabacek, R.; Havrila, R. [Department of Electric Traction and Energetics Faculty of Electrical Engineering, University of Zilina (Slovakia)

    1997-12-31

    This paper deals with the theoretical analysis computer simulation and experimental results of IM fed by a one-to-three phase matrix converter which offers a unique solution for single phase electric traction applications. The proposed drive in comparison with currently used conventional drives reduces the number of power switching elements of the converter, which increases drives dependability and brings lower investment in power electronics used in drive. Further advantage is that the converter is controlled with nearly unity power factor which cuts down the operational expenses and offers higher overall performance of the drive. (orig.) 6 refs.

  4. New active load voltage clamp for HF-link converters

    Energy Technology Data Exchange (ETDEWEB)

    Ljusev, P.; Andersen, M.A.E.

    2005-07-01

    This paper proposes a new active clamp for HF-link converters, which features very high efficiency by returning the clamped energy back to the primary side through a small auxiliary converter. It also increases the reliability of HF-link converters by providing an alternative load current path during malfunctions of the secondary bidirectional bridge. The feasibility of the approach is shown on audio power amplifier prototype. New integrated magnetics design is presented that incorporates both the main power and auxiliary transformer on the same magnetic core. (au)

  5. A high speed digital-to-analogue converter

    International Nuclear Information System (INIS)

    Hallgren, B.I.

    1974-02-01

    An 8-bit Digital-to-Analogue converter of the current-weighting type has been constructed using 8 monolithic integrated circuit transistor arrays -one for each bit. The D/A-converter has a voltage output within the range 0 to -2V. The settling time to within half of the least significant bit is about 50 nsec. The temperature dependence and transient response of the converter has been analysed using computer aided design techniques. A comparison is made between the experimental and simulated transient performance. (Auth.)

  6. Torque converter transient characteristics prediction using computational fluid dynamics

    International Nuclear Information System (INIS)

    Yamaguchi, T; Tanaka, K

    2012-01-01

    The objective of this research is to investigate the transient torque converter performance used in an automobile. A new technique in computational fluid dynamics is introduced, which includes the inertia of the turbine in a three dimensional simulation of the torque converter during a launch condition. The simulation results are compared to experimental test data with good agreement across the range of data. In addition, the simulated flow structure inside the torque converter is visualized and compared to results from a steady-state calculation.

  7. In-pile experimental device for Sirene thermionic converters

    International Nuclear Information System (INIS)

    Bliaux, J.; Durand, J.; Lazare-Chopard, G.

    1969-01-01

    The irradiation device described here, was built for in pile life tests of 100 We SIRENE converters. The nuclear converter is located in a sealed vacuum chamber, which is plugged at the lower end of a coaxial tubing acting as electrical leads. The output power is available on a variable resistive load on the bank of the reactor pool. Thermal, electrical and neutronic parameters of the converter are recorded. Since 1967, two permanent devices allowed five experiments in the swimming pool TRITON (CEN-FAR) and the results, obtained till now, are presented. (authors) [fr

  8. Pulse-width modulated DC-DC power converters

    CERN Document Server

    Kazimierczuk, Marian K

    2008-01-01

    This book studies switch-mode power supplies (SMPS) in great detail. This type of converter changes an unregulated DC voltage into a high-frequency pulse-width modulated (PWM) voltage controlled by varying the duty cycle, then changes the PWM AC voltage to a regulated DC voltage at a high efficiency by rectification and filtering. Used to supply electronic circuits, this converter saves energy and space in the overall system. With concept-orientated explanations, this book offers state-of-the-art SMPS technology and promotes an understanding of the principle operations of PWM converters,

  9. Wide-band charge-to-digital converter

    International Nuclear Information System (INIS)

    Kantserov, V.A.; Strigin, V.B.

    1987-01-01

    CAMAC two-channel charge-to-digital converter on the base of KR1101PD1 microcircuits, is described. Code length of the converter is 11 bits, conversion time makes up 112 μs, sensitivity is equal to 0.25 p cal./channel, integral non-linearity is 0.1%. The converter may be used in different branches both in multichannel data acquisition/processing systems for pulsed signal coding and at fixed gate for measuring constant or slowly varying voltages

  10. Device Loading of Modular Multilevel Converter in Wind Power

    DEFF Research Database (Denmark)

    Popova, L.; Ma, Ke; Blaabjerg, Frede

    2015-01-01

    of the MMC to wind energy systems is studied. The converters used to connect the wind turbine to the grid, which have rated active powers of 2MW and 10MW, are proposed and investigated. The electrical losses and thermal loading of the power devices in the proposed converter solutions are analyzed based...... applications, and the losses are evenly distributed between the submodules of the MMC. However, inside a submodule, the losses of the power devices are not equal, which may lead to the de-rating of the converter....

  11. Computational Fluid Dynamics in Torque Converters: Validation and Application

    OpenAIRE

    Schweitzer, Jean; Gandham, Jeya

    2003-01-01

    This article describes some of the computational fluid dynamics (CFD) work being done on three-element torque converters using a commercially available package CFX TASCflow. The article details some of the work done to validate CFD results and gives examples of ways in which CFD is used in the torque-converter design process. Based on the validation study, it is shown that CFD can be used as a design and analysis tool to make decisions about design direction. Use of CFD in torque converters i...

  12. A nonlinearity compensation method for a matrix converter drive

    DEFF Research Database (Denmark)

    Lee, Kyo-Beum; Blaabjerg, Frede

    2005-01-01

    This paper presents a new method to compensate the nonlinearities for matrix converter drives. The nonlinearities of matrix converter drives such as commutation delay, turn-on and turn-off time of the switching devices, and on-state switching device voltage drop is corrected by a new matrix...... converter model using the direction of current. The proposed method does not need any additional hardware or complicated software and it is easy to realize by applying the algorithm to the conventional vector control. The proposed compensation method is applied for high-performance induction motor drives...

  13. High Efficiency Boost Converter with Three State Switching Cell

    DEFF Research Database (Denmark)

    Klimczak, Pawel; Munk-Nielsen, Stig

    2009-01-01

    is on performance improvement of this type of the converter. Use of foil windings helps to reduce conduction losses in magnetic components and to reduce size of these components. Also it has been demonstrated that the regulation range of this type of converter can be increased by operation with duty cycle lower......The boost converter with the three-state switching cell seems to be a good candidate for a dc-dc stage for non-isolated generators based on alternative energy sources. It provides a high voltage gain, a reduced voltage stress on transistors and limited input current ripples. In this paper the focus...

  14. Triphase Cascaded Converters with Direct Synchronous Pulswidth Modulation

    DEFF Research Database (Denmark)

    Oleschuk, V.; Blaabjerg, Frede; Bose, B. K.

    2002-01-01

    A novel method of direct synchronous pulse-width modulation (PWM) is applied for control of modular multilevel converters consisting from three standard triphase inverter modules along with an 0.33 p.u. output transformer. The proposed method provides synchronisation of the voltage waveforms...... for both each module and the composed voltage at the output of the converter. Multilevel output voltage of the converter has quarter-wave symmetry during the whole range including the zone of overmodulation. Both continuous and discontinuous versions of synchronous PWM, based on a vector approach...

  15. Thyristor voltage converter in induction electric drives with microprocessor control

    Energy Technology Data Exchange (ETDEWEB)

    Braslavsky, I.; Zuzev, A.; Shilin, S. [Electric Drive Department, Urals State Technical University, Ekaterinburg (Russian Federation)

    1997-12-31

    The paper consists of some results on developed pulse model of thyristor voltage converter which is one of the most mathematically complicated unit of electric drive. The model structure and model parameter calculating method are represented. The application of the model allows to analyse stability in `locally` by the linear pulse system theory methods with talking into consideration quantise processes within the converter. Such application provides the obtaining higher accurate results comparing with the non-linear system theory approximate methods. Logarithmic frequency characteristics are used to analyse converter dynamic features and they are represented too. (orig.) 4 refs.

  16. High Efficiency Power Converter for Low Voltage High Power Applications

    DEFF Research Database (Denmark)

    Nymand, Morten

    The topic of this thesis is the design of high efficiency power electronic dc-to-dc converters for high-power, low-input-voltage to high-output-voltage applications. These converters are increasingly required for emerging sustainable energy systems such as fuel cell, battery or photo voltaic based......, and remote power generation for light towers, camper vans, boats, beacons, and buoys etc. A review of current state-of-the-art is presented. The best performing converters achieve moderately high peak efficiencies at high input voltage and medium power level. However, system dimensioning and cost are often...

  17. Design and operation of a thermionic converter in air

    International Nuclear Information System (INIS)

    Horner, M.H.; Begg, L.L.; Smith, J.N. Jr.; Geller, C.B.; Kallnowski, J.E.

    1995-01-01

    An electrically heated thermionic converter has been designed, built and successfully tested in air. Several unique features were incorporated in this converter: an integral cesium reservoir, innovative ceramic-to-metal seals, a heat rejection system coupling the collector to a low temperature heat sink and an innovative cylindrical heater filament. The converter was operated for extended periods of time with the emitter at about 1900 K. the collector at about 700 K, and a power density of over 2 w(e)/sq. cm. Input power transients were run between 50% and 100% thermal power, at up to 1% per second, without instabilities in performance

  18. Soft switching buck-boost converter for photovoltaic power generation; Taiyoko hatsuden no tame no soft switching shokoatsu converter

    Energy Technology Data Exchange (ETDEWEB)

    Lee, H. [Kyungnam University (Korea, Republic of)

    1996-10-27

    A soft switching method with small switching loss was proposed for the purpose of increasing the efficiency of a DC-DC boost converter which converted a DC current generated by solar cells to a variable DC current. Existing current converters are supplemented by using a snubber circuit around the switch so as to protect the switch by a hard switching action. However, with an increase of the output current, snubber loss is increased, reducing the efficiency. In order to solve this problem, the partial resonant switch method was applied to the converter; with this method of partially forming a resonant circuit only at the time of turning on/off of the switch, the switching loss was reduced through the soft switching, thereby making the proposed converter operate with high efficiency. Moreover, the resonant element of the partial resonant circuit using a snubber condenser, the energy accumulated in the condenser was regenerated on the power supply side without loss of snubber. With the regenerated energy, the proposed converter was provided with a smaller ratio of switching to use than the conventional converter. 4 refs., 7 figs., 1 tab.

  19. Application of the matrix converter to power flow control

    Directory of Open Access Journals (Sweden)

    Szcześniak P.

    2014-09-01

    Full Text Available Advanced power electronic converters can provide the means to control power flow and ensure proper and secure operation of the future power grid. The small electrical energy sources dispersed in electrical power systems referred to as distributed generation are one of the most significant parts of future grids - Smart Grids. The threephase, direct matrix converter is an alternative solution to the conventional AC-DC-AC converter for interfacing two AC systems in distributed power generation with different voltage and/or frequency parameters. This paper presents a control analysis of a threephase matrix converter employed as a power interface of future electrical grids. The proposed system has been successfully tested for bidirectional power flow operation with different grid operating conditions, such as, frequency and voltage variation

  20. Complex-Vector Time-Delay Control of Power Converters

    DEFF Research Database (Denmark)

    Blaabjerg, Frede; Loh, P. C.; Tang, Y.

    2008-01-01

    Precise controlling of current produced by power converters is an important topic that has attracted interests over the last few decades. With the recent proliferation of grid-tied converters where the control of power flow is indirectly governed by the accuracy of current tracking, motivation...... a set of load-matching control characteristics that are less sensitive to external noise interferences. These added features, complementing the basic requirement of fast and accurate fundamental positive-sequence tracking, render the proposed scheme as an attractive alternative for high-end converter...... control. Lastly, for proving its practicality, experimental testing of the scheme is performed digitally using a commercial grid converter with some informative results captured and compared with those of an existing scheme....

  1. A New Asymmetrical Current-fed Converter with Voltage Lifting

    Directory of Open Access Journals (Sweden)

    DELSHAD, M.

    2011-05-01

    Full Text Available This paper presents a new zero voltage switching current-fed DC-DC converter with high voltage gain. In this converter all switches (main and auxiliary turn on under zero voltage switching and turn off under almost zero voltage switching due to snubber capacitor. Furthermore, the voltage spike across the main switch due to leakage inductance of forward transformer is absorbed. The flyback transformer which is connected to the output in series causes to high voltage gain and less voltage stress on the power devices. Considering high efficiency and voltage gain of this converter, it is suitable for green generated systems such as fuel cells or photovoltaic systems. The presented experimental results verify the integrity of the proposed converter.

  2. Research on Parallel Three Phase PWM Converters base on RTDS

    Science.gov (United States)

    Xia, Yan; Zou, Jianxiao; Li, Kai; Liu, Jingbo; Tian, Jun

    2018-01-01

    Converters parallel operation can increase capacity of the system, but it may lead to potential zero-sequence circulating current, so the control of circulating current was an important goal in the design of parallel inverters. In this paper, the Real Time Digital Simulator (RTDS) is used to model the converters parallel system in real time and study the circulating current restraining. The equivalent model of two parallel converters and zero-sequence circulating current(ZSCC) were established and analyzed, then a strategy using variable zero vector control was proposed to suppress the circulating current. For two parallel modular converters, hardware-in-the-loop(HIL) study based on RTDS and practical experiment were implemented, results prove that the proposed control strategy is feasible and effective.

  3. LLCL-Filtered Grid Converter with Improved Stability and Robustness

    DEFF Research Database (Denmark)

    Min, Huang; Wang, Xiongfei; Loh, Poh Chiang

    2016-01-01

    LLCL-filter has been proven to introduce more filtering at the converter switching frequency, while using smaller passive components. However, like other higher order filters, it introduces resonance to the grid when used with a grid converter. Its stability and robustness are also affected by grid...... impedance variations, making its design more challenging. To address these concerns, a new parameter design method for LLCL-filter has been formulated in the paper, which when enforced, guarantees robust and stable grid current control regardless of how the grid conditions change. It is thus an enhanced...... method even with no damping added to the grid converter. The method has been applied to the development of an LLCL-filter for testing in the laboratory with a 5-kW, 400-V, and 50-Hz grid converter. The method can also be applied to the lower order LCL-filter with only a slight modification needed....

  4. Thermoelectric converter for SP-100 space reactor power system

    International Nuclear Information System (INIS)

    Terrill, W.R.; Haley, V.F.

    1986-01-01

    Conductively coupling the thermoelectric converter to the heat source and the radiator maximizes the utilization of the reactor and radiator temperatures and thereby minimizes the power system weight. This paper presents the design for the converter and the individual thermoelectric cells that are the building block modules for the converter. It also summarizes progress on the fabrication of initial cells and the results obtained from the preparation of a manufacturing plan. The design developed for the SP-100 system utilizes thermally conductive compliant pads that can absorb the displacement and distortion caused by the combinations of temperatures and thermal expansion coefficients. The converter and cell designs provided a 100 kWe system which met the system requirements. Initial cells were fabricated and tested. The manufacturing plan showed that the chosen materials and processes are compatible with today's production techniques, that the production volume can readily be achieved and that the costs are reasonable

  5. Power electronic converters and systems frontiers and applications

    CERN Document Server

    Trzynadlowski, Andrzej M

    2016-01-01

    Power electronics is a branch of electrical engineering dealing with conversion and control of electric power using semiconductor power switches. This book provides an overview of modern power electronic converters and systems, and their applications.

  6. Effects of cavitation on performance of automotive torque converter

    Directory of Open Access Journals (Sweden)

    Jaewon Ju

    2016-06-01

    Full Text Available Cavitation is a phenomenon whereby vapor bubbles of a flowing liquid are formed in a local region where the pressure of the liquid is below its vapor pressure. It is well known that cavitation in torque converters occurs frequently when a car with an automatic transmission makes an abrupt start. Cavitation is closely related to a performance drop and noise generation at a specific operating condition in a car and a torque converter itself. This study addressed the relation between cavitation and performance in an automotive torque converter in a quantitative and qualitative manner using numerical simulations. The cavitation was calculated at various operating conditions using a commercial flow solver with the homogeneous cavitation model, and the torque converter performance was compared with the experimental data. Numerical results well match to the data and indicate that the cavitation causes significant performance drop, as the pump speed increases or both speed ratio and reference pressure decrease.

  7. High Input Voltage Hall Thruster Discharge Converter, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — The overall scope of this Phase I/II effort is the development of a high efficiency 15kW (nominal) Hall thruster discharge converter. In Phase I, Busek Co. Inc. will...

  8. Converting Sunlight to Mechanical Energy: A Polymer Example of Entropy.

    Science.gov (United States)

    Mathias, Lon J.

    1987-01-01

    This experiment/demonstration provides elementary through high school science students with hands-on experience with polymer entropy. Construction of a simple machine for converting light into mechanical energy is described. (RH)

  9. Concept Study of Foundation Systems for Wave Energy Converters

    DEFF Research Database (Denmark)

    Molina, Salvador Devant; Vaitkunaite, Evelina; Ibsen, Lars Bo

    Analysis of possible foundation solution for Wave Energy Converters (WEC) is presented by investigating and optimizing novel foundation systems recently developed for offshore wind turbines. Gravity based, pile and bucket foundations are innovative foundation systems that are analyzed. Concept st...

  10. Systematic risk variations (beta convertible debenture brazilian companies

    Directory of Open Access Journals (Sweden)

    Renata Drumond Pinto Coelho Antonino

    2010-01-01

    Full Text Available purpose of this article is to analyze the impact of issuing convertible debentures on the systematic risk of Brazilian companies. Some applied researches in the U.S. capital market (STEIN, 1992; LEWIS et al, 2002; RAI, 2005 indicate that convertible debentures may be used as an alternative financing source when adverse selection problem makes stock issuing unattractive financing source. The analysis of Brazilian companies that issued convertible debentures recorded in the period from 1998 to 2006 and that presented liquidity on the market indicated that variation in beta, on average, is positive. These results are coherent with the signaling hypothesis and with the absence of convertible debenture issuing in 2005 and 2006 on the Brazilian market. They also may be related to the precarious financial situation of issuing companies, observed by the analysis of some financial indicators in year of issue and in two pre- e post-issuing years.

  11. A Current-Fed Isolated Bidirectional DC-DC Converter

    DEFF Research Database (Denmark)

    Sun, Xiaofeng; Wu, Xiaoying; Shen, Yanfeng

    2017-01-01

    This paper proposes a current-fed isolated bidirectional DC-DC converter (CF-IBDC) which has the advantages of wide input voltage range, low input current ripple, low conduction losses, and soft switching over the full operating range. Compared with conventional CF-IBDCs, the voltage spikes...... of the low-voltage (LV) side switches in the proposed converter can be eliminated without additional clamp circuits. The converter adopts the pulse width modulation (PWM) plus hybrid phase-shift control scheme such that the bus voltage can match the output voltage by means of the transformer. Thus......, the current stresses and conduction losses of the converter become lower. In addition, the practical ZVS of the secondary-side switches can be realized by adjusting the phase-shift angle within the secondary side when in light load or no load condition. The operating principles and characteristics including...

  12. Unified Digital Periodic Signal Filters for Power Converter Systems

    DEFF Research Database (Denmark)

    Yang, Yongheng; Xin, Zhen; Zhou, Keliang

    2017-01-01

    Periodic signal controllers like repetitive and resonant controllers have demonstrated much potential in the control of power electronic converters, where periodic signals (e.g., ac voltages and currents) can be precisely regulated to follow references. Beyond the control of periodic signals, ac...... signal processing (e.g., in synchronization and pre-filtering) is also very important for power converter systems. Hence, this paper serves to unify digital periodic signal filters so as to maximize their roles in power converter systems (e.g., enhance the control of ac signals). The unified digital...... periodic signal filters behave like a comb filter, but it can also be configured to selectively filter out the harmonics of interest (e.g., the odd-order harmonics in single-phase power converter systems). Moreover, a virtual variable-sampling-frequency unit delay that enables frequency adaptive periodic...

  13. A fast radiation-to-coherent light converter

    International Nuclear Information System (INIS)

    Wang, C.L.; Flatley, J.E.; Stewart, P.H.

    1988-01-01

    We have developed a radiation-to-coherent light converter (RCLC) with a monolithically integrated semiconductor chip that consists of a chromium-doped GaAs photoconductor detector modulates the laser diode, which has been biased above the lasing threshold, thus converting a radiation pulse to an electric pulse and then to a light pulse. The laser pulse is then transmitted to a fast recorder through a high-bandwidth optical fiber. In the absence of a single-step x-ray pumped laser, our converter appears to be the first integrated device that can efficiently convert x-ray flux into coherent light. This device has been tested successfully with the 50-ps electron beams of a 17-MeV linear accelerator and with 50-ns x-ray pulses from a Z-pinch plasma source. 2 refs., 9 figs

  14. Flow in axisymmetric expansion in a catalytic converter

    DEFF Research Database (Denmark)

    Gotfredsen, Erik; Meyer, Knud Erik

    The flow in an axisymmetric expansion (circular diffusor) is used in many different engineering applications, such as heat exchangers, catalytic converters and filters. These applications require a relatively uniform flow at the inlet. To minimise the pressure loss, an ideal solution would...... for a specific local flow rate and a non-uniform inflow to the catalyst will severely reduce the efficiency of the process. Since each ship will have a unique design the flow system, it is desirable to be able to design the system using Computational Fluid Dynamics (CFD). However, CFD fails to predict flow......-scaled model of the catalytic converter is constructed, see figure 1. The experiments are performed at laboratory conditions, with lower pressure, temperature and velocity than the full-scale catalytic converter. The Reynolds number based on the velocity in the inlet pipe and the diameter of the converter...

  15. Assembly processor program converts symbolic programming language to machine language

    Science.gov (United States)

    Pelto, E. V.

    1967-01-01

    Assembly processor program converts symbolic programming language to machine language. This program translates symbolic codes into computer understandable instructions, assigns locations in storage for successive instructions, and computer locations from symbolic addresses.

  16. PLL strategies of grid connected converters under distorted input voltages

    Czech Academy of Sciences Publication Activity Database

    Šimek, Petr; Škramlík, Jiří; Valouch, Viktor

    2014-01-01

    Roč. 59, č. 1 (2014), s. 1-12 ISSN 0001-7043 Institutional support: RVO:61388998 Keywords : voltage source converter * grid - connected applications * phase locked loop Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering

  17. Ultrasonic series resonant converter with integrated L-C-T

    CSIR Research Space (South Africa)

    Smit, MC

    1995-01-01

    Full Text Available The concept of an integrated structure for the capacitor, inductor and transformer of the series resonant converters presented. It is shown that the necessary capacitance can be achieved by using a bifilar primary and the leakage inductance...

  18. Turbo-Brayton Power Converter for Spaceflight Applications, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Future NASA space missions require advanced systems to convert thermal energy into electric power. These systems must be reliable, efficient, and lightweight. In...

  19. Turbo-Brayton Power Converter for Spaceflight Applications, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — Future NASA space missions require advanced systems to convert thermal energy into electric power. These systems must be reliable, efficient, and lightweight. In...

  20. High Efficiency Power Converter for Low Voltage High Power Applications

    DEFF Research Database (Denmark)

    Nymand, Morten

    The topic of this thesis is the design of high efficiency power electronic dc-to-dc converters for high-power, low-input-voltage to high-output-voltage applications. These converters are increasingly required for emerging sustainable energy systems such as fuel cell, battery or photo voltaic based...... energy systems. Applications include systems for emergency power back-up (UPS), de-centralized combined heat and power systems, traction applications such as hybrid electrical vehicles, forklift trucks and special applications such as low emission power generation for truck and ship containers...... be applied to all isolated boost type converters and, in principle, an unlimited number of power stages can be paralleled. Feasibility and operation of the new topology are demonstrated on a dual 3 kW and a quad 10 kW prototype converter. Measured peak efficiency is 98.2% and worst case minimum efficiency...

  1. MULTILEVEL CONVERTERS FOR MICROWELDING BASED ON M-ARY SYSTEM

    Directory of Open Access Journals (Sweden)

    Zhuikov V.

    2012-12-01

    Full Text Available Multilevel converter constructing and functioning principles are given. Two different approaches to increase efficiency are described. Both decisions are compared with typical applications, so advantages and drawbacks are specified.

  2. The APA Style Converter: a Web-based interface for converting articles to APA style for publication.

    Science.gov (United States)

    Li, Ping; Cunningham, Krystal

    2005-05-01

    The APA Style Converter is a Web-based tool with which authors may prepare their articles in APA style according to the APA Publication Manual (5th ed.). The Converter provides a user-friendly interface that allows authors to copy and paste text and upload figures through the Web, and it automatically converts all texts, references, and figures to a structured article in APA style. The output is saved in PDF or RTF format, ready for either electronic submission or hardcopy printing.

  3. Integrated magnetics design for HF-link power converters

    DEFF Research Database (Denmark)

    Ljusev, Petar; Andersen, Michael Andreas E.

    2005-01-01

    This paper deals with the design of integrated magnetics for HF-link converters, where the integrated magnetic components do not necessarily belong to the same voltage loop. Depending on the specific HF-link converter topology, the proposed integrated magnetics can either alleviate the derivation...... of independent auxiliary supply voltages from the main transformer or integrate other magnetic structures, thus saving board space and cutting costs....

  4. Experimental Study on the Langlee Wave Energy Converter

    DEFF Research Database (Denmark)

    Lavelle, John; Kofoed, Jens Peter

    This report concerns the experimental study of the 1:20 scale model of the Langlee Wave Energy Converter (WEC) carried out at Aalborg University’s wave basin during the summer of 2010.......This report concerns the experimental study of the 1:20 scale model of the Langlee Wave Energy Converter (WEC) carried out at Aalborg University’s wave basin during the summer of 2010....

  5. Power electronic converters PWM strategies and current control techniques

    CERN Document Server

    Monmasson, Eric

    2013-01-01

    A voltage converter changes the voltage of an electrical power source and is usually combined with other components to create a power supply. This title is devoted to the control of static converters, which deals with pulse-width modulation (PWM) techniques, and also discusses methods for current control. Various application cases are treated. The book is ideal for professionals in power engineering, power electronics, and electric drives industries, as well as practicing engineers, university professors, postdoctoral fellows, and graduate students.

  6. Integrated magnetics design for HF-link power converters

    Energy Technology Data Exchange (ETDEWEB)

    Ljusev, P.; Andersen, Michael A.E.

    2005-07-01

    This paper deals with the design of integrated magnetics for HF-link converters, where the two integrated magnetic components on the same core do not necessarily belong to the same voltage loop. Depending on the specific HF-link converter topology, the proposed integrated magnetics can either alleviate the derivation of independent auxiliary supply voltages from the main transformer or integrate other magnetic structures, thus saving board space and cutting costs. (au)

  7. Hybrid battery with bi-directional DC/DC converter

    Directory of Open Access Journals (Sweden)

    DUDRIK Jaroslav

    2010-05-01

    Full Text Available Bi-directional buck-boost DC/DC converterfor hybrid battery is described in this paper. The firstpart of the paper is aimed at concept of hybrid battery;main advance compared to conventional accumulatoris explained there. Control circuit with UC3637 andpower circuit of the converter are described in thesecond part of the paper. Experimental results frommeasuring of converter are mentioned in the last part.

  8. Accurate Sliding-Mode Control System Modeling for Buck Converters

    DEFF Research Database (Denmark)

    Høyerby, Mikkel Christian Wendelboe; Andersen, Michael Andreas E.

    2007-01-01

    This paper shows that classical sliding mode theory fails to correctly predict the output impedance of the highly useful sliding mode PID compensated buck converter. The reason for this is identified as the assumption of the sliding variable being held at zero during sliding mode, effectively...... approach also predicts the self-oscillating switching action of the sliding-mode control system correctly. Analytical findings are verified by simulation as well as experimentally in a 10-30V/3A buck converter....

  9. PENGGUNAAN FUZZY LOGIC UNTUK KONTROL PARALLEL CONVERTER DC-DC

    Directory of Open Access Journals (Sweden)

    Bambang Prio Hartono

    2012-09-01

    Full Text Available Abstract: Using system fuzzy logic as control  technology have been used on low load dc-dc converter with combined parallel compiled  dc-dc converter can  obtain big load.   With existence of differrence of component parameter and each parallel compiled converter can obtained different current  and voltage output.  Function of controller  for to do adjustment, so that current which is applied  to  load by each converter  can be obtained  difference error as small as possible or same. The object of research is developing design of large signal dc-dc converter which is  combined with using  FLC so that  obtain  better performance.  To get better performance have been made plant model and simulation with CDE method.  The more systematic  system and design is needed to overcome bigger load  on dc-dc converter, so that parallel  compiled current master slave control system on dc-dc converter with using fuzzy logic  controller is used. Result of  research showed that error or difference of  current  which is applied to load can handled by fuzzy logic  controller.  Technic of current and voltage controller co to do adjustment current and voltage distribution  equally to load.  Distribution of iL1,iL2 and  output voltage Vo on dc-dc  converter with load 2,25 until  7,875 and voltage  100  until 120 volt,  load current beetwen  12 until 48, % relatif  error  Vo  0,4% until  0,9%.

  10. An improved 4-step commutation method application for matrix converter

    DEFF Research Database (Denmark)

    Guo, Yu; Guo, Yougui; Deng, Wenlang

    2014-01-01

    A novel four-step commutation method is proposed for matrix converter cell, 3 phase inputs to 1 phase output in this paper, which is obtained on the analysis of published commutation methods for matrix converter. The first and fourth step can be shorter than the second or third one. The discussed...... method here is implemented by programming in VHDL language. Finally, the novel method in this paper is verified by experiments....

  11. The flying-capacitor SEPIC converter with the balancing circuit

    Directory of Open Access Journals (Sweden)

    Kawa Adam

    2016-09-01

    Full Text Available The paper presents investigation results of the natural balancing phenomena in the flying-capacitor SEPIC converters. The SEPIC converters topologies can be reconfigured to the flying-capacitor topology. Owing to this modification the advantageous increase of frequency of the current in the chokes and the decrease of semiconductors voltages can be achieved which is shown in this paper. Similarly to other multilevel flying capacitor topologies the adequate voltage sharing of the flying capacitors is an important issue for safe operation of the converter. The paper focuses on the analysis of the flying capacitor voltages balancing in the converter by natural currents as well as by the application of the additional RLC balancing booster. The paper proves that the natural balancing can be achieved by the specific application of the balancing circuit in the flying-capacitor SEPIC topology and proves the specific differences in the balancing process by natural currents of converter and with the usage of the balancing circuit. An operation of the converter with the balancing circuit and the natural balancing ability is studied here.

  12. Fuzzy Controlled Parallel AC-DC Converter for PFC

    Directory of Open Access Journals (Sweden)

    M Subba Rao

    2011-01-01

    Full Text Available Paralleling of converter modules is a well-known technique that is often used in medium-power applications to achieve the desired output power by using smaller size of high frequency transformers and inductors. In this paper, a parallel-connected single-phase PFC topology using flyback and forward converters is proposed to improve the output voltage regulation with simultaneous input power factor correction (PFC and control. The goal of the control is to stabilize the output voltage of the converter against the load variations. The paper presents the derivation of fuzzy control rules for the dc/dc converter circuit and control algorithm for regulating the dc/dc converter. This paper presents a design example and circuit analysis for 200 W power supply. The proposed approach offers cost effective, compact and efficient AC/DC converter by the use of parallel power processing. MATLAB/SIMULINK is used for implementation and simulation results show the performance improvement.

  13. Early Oscillation Detection for DC/DC Converter Fault Diagnosis

    Science.gov (United States)

    Wang, Bright L.

    2011-01-01

    The electrical power system of a spacecraft plays a very critical role for space mission success. Such a modern power system may contain numerous hybrid DC/DC converters both inside the power system electronics (PSE) units and onboard most of the flight electronics modules. One of the faulty conditions for DC/DC converter that poses serious threats to mission safety is the random occurrence of oscillation related to inherent instability characteristics of the DC/DC converters and design deficiency of the power systems. To ensure the highest reliability of the power system, oscillations in any form shall be promptly detected during part level testing, system integration tests, flight health monitoring, and on-board fault diagnosis. The popular gain/phase margin analysis method is capable of predicting stability levels of DC/DC converters, but it is limited only to verification of designs and to part-level testing on some of the models. This method has to inject noise signals into the control loop circuitry as required, thus, interrupts the DC/DC converter's normal operation and increases risks of degrading and damaging the flight unit. A novel technique to detect oscillations at early stage for flight hybrid DC/DC converters was developed.

  14. Power electronic converters modeling and control with case studies

    CERN Document Server

    Bacha, Seddik; Bratcu, Antoneta Iuliana

    2014-01-01

    Modern power electronic converters are involved in a very broad spectrum of applications: switched-mode power supplies, electrical-machine-motion-control, active power filters, distributed power generation, flexible AC transmission systems, renewable energy conversion systems and vehicular technology, among them. Power Electronics Converters Modeling and Control teaches the reader how to analyze and model the behavior of converters and so to improve their design and control. Dealing with a set of confirmed algorithms specifically developed for use with power converters, this text is in two parts: models and control methods. The first is a detailed exposition of the most usual power converter models: ·        switched and averaged models; ·        small/large-signal models; and ·        time/frequency models. The second focuses on three groups of control methods: ·        linear control approaches normally associated with power converters; ·        resonant controllers b...

  15. Coordinated Control of Wave Energy Converters Subject to Motion Constraints

    Directory of Open Access Journals (Sweden)

    Liguo Wang

    2016-06-01

    Full Text Available In this paper, a generic coordinated control method for wave energy converters is proposed, and the constraints on motion amplitudes and the hydrodynamic interaction between converters are considered. The objective of the control problem is to maximize the energy converted from ocean waves, and this is achieved by coordinating the power take-off (PTO damping of each wave energy converter in the frequency domain in each sea state. In a case study, a wave energy farm consisting of four converters based on the concept developed by Uppsala University is studied. In the solution, motion constraints, including constraints on the amplitudes of displacement and velocity, are included. Twelve months of sea states, based on measured wave data at the Lysekil test site on the Swedish west coast, are used in the simulation to evaluate the performance of the wave energy farm using the new method. Results from the new coordinated control method and traditional control method are compared, indicating that the coordinated control of wave energy converters is an effective way to improve the energy production of wave energy farm in harmonic waves.

  16. Bi-directional power control system for voltage converter

    Science.gov (United States)

    Garrigan, Neil Richard; King, Robert Dean; Schwartz, James Edward

    1999-01-01

    A control system for a voltage converter includes: a power comparator for comparing a power signal on input terminals of the converter with a commanded power signal and producing a power comparison signal; a power regulator for transforming the power comparison signal to a commanded current signal; a current comparator for comparing the commanded current signal with a measured current signal on output terminals of the converter and producing a current comparison signal; a current regulator for transforming the current comparison signal to a pulse width modulator (PWM) duty cycle command signal; and a PWM for using the PWM duty cycle command signal to control electrical switches of the converter. The control system may further include: a command multiplier for converting a voltage signal across the output terminals of the converter to a gain signal having a value between zero (0) and unity (1), and a power multiplier for multiplying the commanded power signal by the gain signal to provide a limited commanded power signal, wherein power comparator compares the limited commanded power signal with the power signal on the input terminals.

  17. High-Feedback Operation of Power Electronic Converters

    Directory of Open Access Journals (Sweden)

    Gennady Y. Mikhal'chenko

    2013-03-01

    Full Text Available The purpose of this review is to provide a survey of some of the most important bifurcation phenomena that one can observe in pulse-modulated converter systems when operating with high corrector gain factors. Like other systems with switching control, electronic converter systems belong to the class of piecewise-smooth dynamical systems. A characteristic feature of such systems is that the trajectory is “sewed” together from subsequent discrete parts. Moreover, the transitions between different modes of operation in response to a parameter variation are often qualitatively different from the bifurcations we know for smooth systems. The review starts with an introduction to the concept of border-collision bifurcations and also demonstrates the approach by which the full dynamics of the piecewise-linear, time-continuous system can be reduced to the dynamics of a piecewise-smooth map. We describe the main bifurcation structures that one observes in three different types of converter systems: (1 a DC/DC converter; (2 a multi-level DC/DC converter; and (3 a DC/AC converter. Our focus will be on the bifurcations by which the regular switching dynamics becomes unstable and is replaced by ergodic or resonant periodic dynamics on the surface of a two-dimensional torus. This transition occurs when the feedback gain is increased beyond a certain threshold, for instance in Electronics 2013, 2 114 order to improve the speed and accuracy of the output voltage regulation. For each of the three converter types, we discuss a number of additional bifurcation phenomena, including the formation and reconstruction of multi-layered tori and the appearance of phase-synchronized quasiperiodicity. Our numerical simulations are compared with experimentally observed waveforms.

  18. All-optical 40 Gbit/s compact integrated interferometric wavelength converter

    DEFF Research Database (Denmark)

    Jørgensen, Carsten; Danielsen, Søren Lykke; Hansen, Peter Bukhave

    1997-01-01

    An interferometric Michelson wavelength converter is presented that combines a speed-optimized semiconductor optical amplifier technology with the benefits of the integrated interferometer showing 40-Gbit/s wavelength conversion. The optimized wavelength converter demonstrates noninverted converted...

  19. SoC Design Approach Using Convertibility Verification

    Directory of Open Access Journals (Sweden)

    Basu Samik

    2008-01-01

    Full Text Available Abstract Compositional design of systems on chip from preverified components helps to achieve shorter design cycles and time to market. However, the design process is affected by the issue of protocol mismatches, where two components fail to communicate with each other due to protocol differences. Convertibility verification, which involves the automatic generation of a converter to facilitate communication between two mismatched components, is a collection of techniques to address protocol mismatches. We present an approach to convertibility verification using module checking. We use Kripke structures to represent protocols and the temporal logic to describe desired system behavior. A tableau-based converter generation algorithm is presented which is shown to be sound and complete. We have developed a prototype implementation of the proposed algorithm and have used it to verify that it can handle many classical protocol mismatch problems along with SoC problems. The initial idea for -based convertibility verification was presented at SLA++P '07 as presented in the work by Roopak Sinha et al. 2008.

  20. Sub-picosecond Resolution Time-to-Digital Converter

    Energy Technology Data Exchange (ETDEWEB)

    Bratov, Vladimir [Advanced Science and Novel Technology Company, Rancho Palos Verdes, CA (United States); Katzman, Vladimir [Advanced Science and Novel Technology Company, Rancho Palos Verdes, CA (United States); Binkley, Jeb [Advanced Science and Novel Technology Company, Rancho Palos Verdes, CA (United States)

    2006-03-30

    Time-to-digital converters with sub-picosecond resolutions are needed to satisfy the requirements of time-on-flight measurements of the next generation of high energy and nuclear physics experiments. The converters must be highly integrated, power effective, low cost, and feature plug-and-play capabilities to handle the increasing number of channels (up to hundreds of millions) in future Department of Energy experiments. Current state-off-the-art time-to-digital converter integrated circuits do not have the sufficient degree of integration and flexibility to fulfill all the described requirements. During Phase I, the Advanced Science and Novel Technology Company in cooperation with the nuclear physics division of the Oak Ridge National Laboratory has developed the architecture of a novel time-to-digital converter with multiple channels connected to an external processor through a special interfacing block and synchronized by clock signals generated by an internal phase-locked loop. The critical blocks of the system including signal delay lines and delay-locked loops with proprietary differential delay cells, as well as the required digital code converter and the clock period counter have been designed and simulated using the advanced SiGe120 BiCMOS technological process. The results of investigations demonstrate a possibility to achieve the digitization accuracy within 1ps. ADSANTEC has demonstrated the feasibility of the proposed concept in computer simulations. The proposed system will be a critical component for the next generation of NEP experiments.

  1. Advanced Catalytic Converter in Gasoline Enginer Emission Control: A Review

    Directory of Open Access Journals (Sweden)

    Leman A.M.

    2017-01-01

    Full Text Available Exhaust emission from automobile source has become a major contributor to the air pollution and environmental problem. Catalytic converter is found to be one of the most effective tools to reduce the overwhelming exhaust pollutants in our environment. The development of sustainable catalytic converter still remains a critical issue due to the stringent exhaust emission regulations. Another issue such as price and availability of the precious metal were also forced the automotive industry to investigate the alternatives for producing a better replacement for the material used in catalytic converter. This paper aims at reviewing the present development and improvement on the catalytic converter used on the reduction of exhaust emission in order to meet the regulations and market demand. The use of new catalyst such as to replace the noble metal material of Platinum (Pt, Palladium (Pd and Rhodium (Rh has been reviewed. Material such as zeolite, nickel oxide and metal oxide has been found to effectively reduce the emission than the commercial converter. The preparation method of the catalyst has also evolved through the years as it is to ensure a good characteristic of a good monolith catalyst. Ultrasonic treatment with combination of electroplating technique, citrate method and Plasma Electrolytic Oxidation (PEO has been found as the latest novel preparation method on producing an effective catalyst in reducing the exhaust emission.

  2. Digital control of grid connected converters for distributed power generation

    Energy Technology Data Exchange (ETDEWEB)

    Skjellnes, Tore

    2008-07-01

    Pulse width modulated converters are becoming increasingly popular as their cost decreases and power rating increases. The new trend of small scale power producers, often using renewable energy sources, has created new demands for delivery of energy to the grid. A major advantage of the pulse width modulated converter is the ability to control the output voltage at any point in the voltage period. This enables rapid response to load changes and non-linear loads. In addition it can shape the voltage in response to the output current to create an outward appearance of a source impedance. This is called a virtual impedance. This thesis presents a controller for a voltage controlled three phase pulse width modulated converter. This controller enables operation in standalone mode, in parallel with other converters in a micro grid, and in parallel with a strong main grid. A time varying virtual impedance is presented which mainly attenuates reactive currents. A method of investigating the overall impedance including the virtual impedance is presented. New net standards have been introduced, requiring the converter to operate even during severe dips in the grid voltage. Experiments are presented verifying the operation of the controller during voltage dips. (Author). 37 refs., 65 figs., 10 tabs

  3. Capacitor performance limitations in high power converter applications

    DEFF Research Database (Denmark)

    El-Khatib, Walid Ziad; Holbøll, Joachim; Rasmussen, Tonny Wederberg

    2013-01-01

    High voltage low inductance capacitors are used in converters as HVDC-links, snubber circuits and sub model (MMC) capacitances. They facilitate the possibility of large peak currents under high frequent or transient voltage applications. On the other hand, using capacitors with larger equivalent...... series inductances include the risk of transient overvoltages, with a negative effect on life time and reliability of the capacitors. These allowable limits of such current and voltage peaks are decided by the ability of the converter components, including the capacitors, to withstand them over...... ratings and capacitances where investigated and compared a) on a component scale, characterizing the capacitors transient performance and b) as part of different converter applications, where the series inductance plays a role. In that way, better insight is achieved on how the capacitor construction can...

  4. Decentralized Interleaving of Paralleled Dc-Dc Buck Converters: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, Brian B [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Rodriguez, Miguel [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Sinha, Mohit [University of Minnesota; Dhople, Sairaj [University of Minnesota; Poon, Jason [University of California at Berkeley

    2017-09-01

    We present a decentralized control strategy that yields switch interleaving among parallel connected dc-dc buck converters without communication. The proposed method is based on the digital implementation of the dynamics of a nonlinear oscillator circuit as the controller. Each controller is fully decentralized, i.e., it only requires the locally measured output current to synthesize the pulse width modulation (PWM) carrier waveform. By virtue of the intrinsic electrical coupling between converters, the nonlinear oscillator-based controllers converge to an interleaved state with uniform phase-spacing across PWM carriers. To the knowledge of the authors, this work represents the first fully decentralized strategy for switch interleaving of paralleled dc-dc buck converters.

  5. GPS Synchronization of Smart Distributed Converters for Microgrid Applications

    Directory of Open Access Journals (Sweden)

    Tarek A. Youssef

    2018-03-01

    Full Text Available In this paper, a smart distributed DC/DC converter synchronization advanced technique and phase angle optimization algorithm are proposed using to reduce the DC bus overall ripple. A global positioning system-based scheme is used to synchronize the carrier among the distributed converters. The carrier phase angle optimization among the different converters is inspired by Carrier-Sense Multiple Access protocol. The proposed system is simulated and analyzed using Matlab/Simulink program. As a proof of concept of the proposed technique, two case studies have been investigated under equal and unequal load sharing among the distributed generators. The proposed algorithm shows a significant reduction in the DC bus voltage ripple. To prove the concept, a laboratory test-bed has been built and the proposed algorithm has been implemented to validate the theoretical and simulation results. The close agreement between the experimental and simulation results demonstrates the effectiveness and validity of the proposed algorithm.

  6. Four-quadrant flyback converter for direct audio power amplification

    Energy Technology Data Exchange (ETDEWEB)

    Ljusev, P.; Andersen, Michael A.E.

    2005-07-01

    This paper presents a bidirectional, four-quadrant yback converter for use in direct audio power amplication. When compared to the standard Class-D switching-mode audio power amplier with separate power supply, the proposed four-quadrant flyback converter provides simple and compact solution with high efciency, higher level of integration, lower component count, less board space and eventually lower cost. Both peak and average current-mode control for use with 4Q flyback power converters are described and compared. Integrated magnetics is presented which simplies the construction of the auxiliary power supplies for control biasing and isolated gate drives. The feasibility of the approach is proven on audio power amplier prototype for subwoofer applications. (au)

  7. Direct Torque Control of Matrix Converter Fed Induction Motor Drive

    Directory of Open Access Journals (Sweden)

    JAGADEESAN Karpagam

    2011-10-01

    Full Text Available This paper presents the Direct TorqueControl (DTC of induction motor drive using matrixconverters. DTC is a high performance motor controlscheme with fast torque and flux responses. However,the main disadvantage of conventional DTC iselectromagnetic torque ripple. In this paper, directtorque control for Induction Motors using MatrixConverters is analysed and points out the problem ofthe electromagnetic torque ripple which is one of themost important drawbacks of the Direct TorqueControl. Besides, the matrix converter is a single-stageac-ac power conversion device without dc-link energystorage elements. Matrix converter (MC may becomea good alternative to voltage-source inverter (VSI.This work combines the advantages of the matrixconverter with those of the DTC technique, generatingthe required voltage vectors under unity input powerfactor operation. Simulation results demonstrates theeffectiveness of the torque control.

  8. Operation and maintenance strategies for wave energy converters

    DEFF Research Database (Denmark)

    Ambühl, Simon; Marquis, Laurent; Kofoed, Jens Peter

    2015-01-01

    Inspection and maintenance costs are a significant contributor to the cost of energy for wave energy converters. There are different operation and maintenance strategies for wave energy converters. Maintenance can be performed after failure (corrective) or before a breakdown (preventive) occurs....... Furthermore, a helicopter and boats can be used to transport equipment and personnel to the device, or the whole device can be towed to a harbour for operation and maintenance actions. This article describes, among others, a risk-based inspection and maintenance planning approach where the overall repair...... and maintenance costs estimations for wave energy converter applications including real weather data and damage accumulation. Furthermore, uncertainties related with costs, structural damage accumulation, inspection accuracy and different maintenance strategies can be included. This article contains a case study...

  9. Analysis of Symmetrical Pulse Width Modulation Strategies for Matrix Converters

    DEFF Research Database (Denmark)

    Larsen, K.B.; Jorgensen, A.H.; Helle, Lars

    2002-01-01

    This paper presents a new and easy way to understand the derivation of the modulation functions for matrix converters. It is shown how the duty cycles can be calculated using techniques known from the back-to-back (B2B) voltage source inverter (VSI), thus making the subject accessible to people...... with prior knowledge in standard drives. A new modulation strategy is presented minimizing harmonic distortion compared to the standard double-sided space vector modulation for matrix converters. An improvement to an existing modulator is also presented where the proposed modification improves the harmonic...... performance. The strategies are compared both analytically and by the use of both simulations and measurements on a 12 kW matrix converter prototype.It is found that the proposed modulator has superior performance compared to modulators with equal switching frequencies and an equal number of switchings....

  10. Angle Stability Analysis for Voltage-Controlled Converters

    DEFF Research Database (Denmark)

    Lin, Hengwei; Jia, Chenxi; Guerrero, Josep M.

    2017-01-01

    a criterion to analyze the quasi-steady angle stability and the direct current (DC) side stability for VSCs. The operating limit and the angle instability mechanism are revealed, which is generally applicable to the voltage-controlled converters. During the analysis, the influence of the parameters on angle...... stability is studied. Further, the difference on instability mechanism between power electronic converters and synchronous generators are explained in detail. Finally, experiment results with corrective actions verify the analysis.......Power electronics based voltage source converters (VSCs) keep increasing in modern electrical systems. As a branch of stability problems, angle stability is significant for an electrical system. Based on small disturbance analysis and time scale decomposition perspective, this paper proposes...

  11. Half bridge resonant converter for ignition of thermal plasmas

    International Nuclear Information System (INIS)

    Pena E, L.

    1997-01-01

    In this work the background, design, implementation and performance of a half bridge resonant converter (HBRC) used as an electronic ignition system for arc plasma torch generation is presented. The significance of the design lies in its simplicity, versatility and low cost. The system operates like a high voltage supply attached to electrodes before gaseous breakdown and like open circuit when electric arc is established. Resonant converter is implemented with a high voltage and high speed power driver intended for control the power MOSFET transistors connected in half bridge topology with L C load. The HBRC operates besides interference into domestic electric supply line (120 V, 60 Hz) as well electric measurement devices. Advantages and limitations of the converter are reviewed. Experimental impedance variation in the medium as a function of frequency operation and some experiences in striking arcs are also presented. (Author)

  12. Method of stabilizing a laser apparatus with wavelength converter

    DEFF Research Database (Denmark)

    2013-01-01

    A method of controlling beam quality and stability of a laser apparatus, the laser apparatus comprising, a diode laser (10) providing first radiation of at least a first wavelength, and a frequency conversion unit (12) configured to frequency-convert the first radiation from the diode laser......) into the first section (222), a second contact (221) for injecting a second current (I2) into the second section (223), and means for controlling a temperature of the diode laser; wherein the method comprises monitoring a first parameter indicative of the power content of a dominant lobe of the first radiation...... and to output the frequency-converted radiation (213), the frequency-converted radiation having at least a second wavelength different from the first wavelength, the diode laser (10) comprising at least a first and a second section (222,223), a first contact (220) for injecting a first current (I1...

  13. Accurate Modeling of Buck Converters with Magnetic-Core Inductors

    DEFF Research Database (Denmark)

    Astorino, Antonio; Antonini, Giulio; Swaminathan, Madhavan

    2015-01-01

    In this paper, a modeling approach for buck converters with magnetic-core inductors is presented. Due to the high nonlinearity of magnetic materials, the frequency domain analysis of such circuits is not suitable for an accurate description of their behaviour. Hence, in this work, a timedomain...... model of buck converters with magnetic-core inductors in a SimulinkR environment is proposed. As an example, the presented approach is used to simulate an eight-phase buck converter. The simulation results show that an unexpected system behaviour in terms of current ripple amplitude needs the inductor core...

  14. CAS course on Power Converters in Baden, Switzerland

    CERN Multimedia

    CERN Accelerator School

    2014-01-01

    The CERN Accelerator School (CAS) and the Paul Scherrer Institute (PSI) recently organised a specialised course on Power Converters, which was held at the Hotel du Parc in Baden, Switzerland from 7 to 14 May 2014.   Photo courtesy of Markus Fischer, Paul Scherrer Institut. Following some recapitulation lectures on accelerators and the requirements on power converters, the course covered a wide range of topics related to the different types of power converters needed for particle accelerators. Topical seminars completed the programme. The course was very successful, attended by 84 students representing 21 nationalities, mostly from European countries but also from America, Brazil, Canada, China, Iran, Jordan and Thailand. Feedback from the participants was very positive, reflecting the high standard of the lectures and teaching. In addition to the academic programme, the participants also had an opportunity to take part in a full-day site visit to ABB and PSI and an excursion to the Rhine Fall...

  15. On the dynamics of a novel ocean wave energy converter

    KAUST Repository

    Orazov, B.

    2010-11-01

    Buoy-type ocean wave energy converters are designed to exhibit resonant responses when subject to excitation by ocean waves. A novel excitation scheme is proposed which has the potential to improve the energy harvesting capabilities of these converters. The scheme uses the incident waves to modulate the mass of the device in a manner which amplifies its resonant response. To illustrate the novel excitation scheme, a simple one-degree of freedom model is developed for the wave energy converter. This model has the form of a switched linear system. After the stability regime of this system has been established, the model is then used to show that the excitation scheme improves the power harvesting capabilities by 2565 percent even when amplitude restrictions are present. It is also demonstrated that the sensitivity of the device\\'s power harvesting capabilities to changes in damping becomes much smaller when the novel excitation scheme is used. © 2010 Elsevier Ltd. All rights reserved.

  16. High voltage direct current transmission converters, systems and DC grids

    CERN Document Server

    Jovcic, Dragan

    2015-01-01

    This comprehensive reference guides the reader through all HVDC technologies, including LCC (Line Commutated Converter), 2-level VSC and VSC HVDC based on modular multilevel converters (MMC) for an in-depth understanding of converters, system level design, operating principles and modeling. Written in a tutorial style, the book also describes the key principles of design, control, protection and operation of DC transmission grids, which will be substantially different from the practice with AC transmission grids. The first dedicated reference to the latest HVDC technologies and DC grid developments; this is an essential resource for graduate students and researchers as well as engineers and professionals working on the design, modeling and operation of DC grids and HVDC.

  17. RESONANT STEP-DOWN DC-DC POWER CONVERTERS

    DEFF Research Database (Denmark)

    2015-01-01

    charged from the input voltage and discharged to the output capacitor through the galvanic isolation barrier by a semiconductor switch arrangement in accordance with a switch control signal to produce the converter output voltage. The resonant step-down DC-DC power converter comprises an electrical short...... and an input capacitor coupled between the positive and negative input terminals and the secondary side circuit comprises an output capacitor chargeable to a converter output voltage between a first positive electrode and a second negative electrode. A resonant network is con- figured for alternatingly being......-circuit connection across the galvanic isolation barrier connecting, in a first case, the second negative electrode of the output capacitor to the positive input terminal of the primary side circuit or, in a second case, connecting the second positive electrode of the output capacitor to the negative input terminal...

  18. Step-Up DC-DC Power Converter

    DEFF Research Database (Denmark)

    2015-01-01

    being charged from the input voltage and discharged to the output capacitor through the galvanic isolation barrier in accordance with a switch control signal to produce the converter output voltage. The step-up DC-DC power converter comprises an electrical short-circuit connection across the galvanic...... capacitor coupled between the positive and negative input terminals and the secondary side circuit comprises an output capacitor chargeable to a converter output voltage between a first positive electrode and a second negative electrode. A switched energy storage network is configured for alternatingly...... isolation barrier connecting, in a first case, the second negative electrode of the output capacitor to the positive input terminal of the primary side circuit or, in a second case, connecting the second positive electrode of the output capacitor to the negative input terminal of the primary side circuit...

  19. Method for converting uranium oxides to uranium metal

    International Nuclear Information System (INIS)

    Duerksen, W.K.

    1988-01-01

    A method for converting uranium oxide to uranium metal is described comprising the steps of heating uranium oxide in the presence of a reducing agent to a temperature sufficient to reduce the uranium oxide to uranium metal and form a heterogeneous mixture of a uranium metal product and oxide by-products, heating the mixture in a hydrogen atmosphere at a temperature sufficient to convert uranium metal in the mixture to uranium hydride, cooling the resulting uranium hydride-containing mixture to a temperature sufficient to produce a ferromagnetic transition in the uranium hydride, magnetically separating the cooled uranium hydride from the mixture, and thereafter heating the separated uranium hydride in an inert atmosphere to a temperature sufficient to convert the uranium hydride to uranium metal

  20. Piezoelectric transformer based power converters; design and control

    DEFF Research Database (Denmark)

    Rødgaard, Martin Schøler

    the advantage of being purely primary side based. A revolutionary bi-directional control method is proposed, which utilizes active phase shift of the output rectifier that enables bi-directional power flow. Soft switching operation is maintained over the full power flow modulation range, ensuring optimal......The last two decades of research into piezoelectric transformer (PT) based power converters have led to some extensive improvements of the technology, but it still struggles to get its commercial success. This calls for further research and has been the subject of this work, in order to enable...... the utilization of the PT technology advantages, reduce cost and increase competitiveness. First of all an overview of the basic PT technology used in general power converters is given, including the basic piezoelectric nature, converter topologies and control methods. Compared to traditional magnetic technology...

  1. Quartz crystal microbalance based on passive frequency to voltage converter

    International Nuclear Information System (INIS)

    Burda, Ioan; Tunyagi, Arthur

    2012-01-01

    In dynamics of evaporation or drying of microdrops from a solid surface, a faster and precise quartz crystal microbalance (QCM) is needed. The fast QCM based on frequency to voltage converter is an attractive and powerful tool in the investigation of the dynamic regime of evaporation to translate the frequency shift in terms of a continuous voltage change. The frequency shift monitoring in fast QCM applications is a real challenge for electronic processing interface. Originally developed as a frequency shift processing interface, this novel passive frequency to voltage converter can produce faster, stable, and accurate results in regard to the QCM sensor behavior. In this article, the concept and circuit of passive frequency to voltage converter will be explained followed by static and dynamic characterization. Experimental results of microdrops evaporation will be given.

  2. Simulation of closed loop controlled boost converter for solar installation

    Directory of Open Access Journals (Sweden)

    Kalirasu Athimulam

    2010-01-01

    Full Text Available With the shortage of the energy and ever increasing of the oil price, research on the renewable and green energy sources, especially the solar arrays and the fuel cells, becomes more and more important. How to achieve high stepup and high efficiency DC/DC converters is the major consideration in the renewable power applications due to the low voltage of PV arrays and fuel cells. In this paper digital simulation of closed loop controlled boost converter for solar installation is presented. Circuit models for open loop and closed loop controlled systems are developed using the blocks of simulink. The simulation results are compared with the theoretical results. This converter has advantages like improved power factor, fast response and reduced hardware. .

  3. Speed and position sensorless control of permanent magnet synchronous motor in matrix converter and voltage source converter applications

    Energy Technology Data Exchange (ETDEWEB)

    Eskola, M.

    2006-07-01

    In this thesis the sensorless control of a permanent magnet synchronous motor (PMSM) is studied. The study has two main purposes. The first is to find a simple and effective method to estimate the rotor position and angular speed of the PMSM. The second is to test the applicability of a matrix converter in sensorless PMSM drives. A matrix converter (MC) enables a direct frequency conversion without DC-link with energy storage. In this thesis two matrix converter topologies, direct and indirect, are studied. The vector modulation and the current commutation strategies of a matrix converter are described. Non-ideal properties of frequency converters such as dead times, overlapping times and voltage losses over semiconductors are disturbances for a control system and position estimator. These non-idealities are studied and the properties of a conventional voltage source inverter are compared to direct and indirect MC topologies. The rotor position and angular speed of the PMSM can be estimated by various methods. Estimators can be divided into model based estimators and signal injection estimators. Model based estimators calculate mechanical quantities using the mathematical representation of the motor. Injection methods usually exploit the saliency of the PMSM. Injected voltage creates currents which are modulated by the rotor position. The position information can be extracted from measured currents. In this thesis the best features of model based and injection estimators are combined. In the proposed hybrid method signal injection is used at low speeds and the transition to model based estimator is performed when the speed increases. The estimator methods used in the hybrid estimator are selected by a comparative analysis and simulations. The most important criteria in the selection of the estimator method in this thesis are: simple algorithm and no need for modification of the modulator software or frequency converter. The suitability of the proposed hybrid

  4. A collimator-converter system for IEC propulsion

    Science.gov (United States)

    Momota, Hiromu; Miley, George H.

    2002-01-01

    The collimator-converter system extracts fusion power from D-3He fueled IEC devices and provides electricity needed to operate ionic thrusters and other-power components. The whole system is linear and consists of a series of collimator units at the center, magnetic expander units at both sides of the fusion units, followed by direct energy converters at both ends. This system is enclosed in a vacuum chamber with a magnetic channel provided by magnetic solenoids out of respective chambers. The fusion unit consists of an IEC fusion core, a pair of coils anti-parallel to the solenoid coils, and a stabilization coil that stabilizes the position of coil pair coils. The IEC fusion core is installed at the center of the pair coils. After the magnetic expander, velocities of fusion particles from D-3He fueled IEC units are directed to the magnetic channel, which guides energetic fusion particles as well as leaking unburned fuel components to a high-efficiency traveling wave direct energy converter (TWDEC). Leaking unburned fuel components are separated with a magnetic separator at the entrance of a direct energy converter and pumped out for further refueling. A TWDEC is made of an array of metallic meshed grids, each of which is connected to every terminal with an external transmission circuit. The transmission line couples to the direct energy converter. Substations for electricity, a cryogenic plant, and various power control systems are outside of the vacuum chamber. The length of the cylindrical system is essentially determined by the proton energy of 14.8 MeV and the radius should be large so as to reduce power flow density. The present system provides 250 MWf fusion power and converting it to 150 MWc electricity. Its size is 150 m(length)×6.6 m(diameter) in size and 185 tons in weight. .

  5. Power Management and Distribution System Developed for Thermionic Power Converters

    Science.gov (United States)

    Baez, Anastacio N.

    1998-01-01

    A spacecraft solar, bimodal system combines propulsion and power generation into a single integrated system. An Integrated Solar Upper Stage (ISUS) provides orbital transfer capabilities, power generation for payloads, and onboard propulsion to the spacecraft. A key benefit of a bimodal system is a greater payload-to-spacecraft mass ratio resulting in lower launch vehicle requirements. Scaling down to smaller launch vehicles increases space access by reducing overall mission cost. NASA has joined efforts with the Air Force Phillips Laboratory to develop enabling technologies for such a system. The NASA/Air Force bimodal concept uses solar concentrators to focus energy into an integrated power plant. This power plant consists of a graphite core that stores thermal energy within a cavity. An array of thermionic converters encircles the graphite cavity and provides electrical energy conversion functions. During the power generation phase of the bimodal system, the thermionic converters are exposed to the heated cavity and convert the thermal energy to electricity. Near-term efforts of the ISUS bimodal program are focused on a ground demonstration of key technologies in order to proceed to a full space flight test. Thermionic power generation is one key technology of the bimodal concept. Thermionic power converters impose unique operating requirements upon a power management and distribution (PMAD) system design. Single thermionic converters supply large currents at very low voltages. Operating voltages can vary over a range of up to 3 to 1 as a function of operating temperature. Most spacecraft loads require regulated 28-volts direct-current (Vdc) power. A combination of series-connected converters and powerprocessing boosters is required to deliver power to the spacecraft's payloads at this level.

  6. Dynamic Performance of Grid Converters using Adaptive DC Voltage Control

    DEFF Research Database (Denmark)

    Trintis, Ionut; Sun, Bo; Guerrero, Josep M.

    2014-01-01

    This paper investigates a controller that ensures minimum operating dc-link voltage of a back-to-back converter system. The dc-link voltage adapts its reference based on the system state, reference given by an outer loop to the dc-link voltage controller. The operating dc-link voltage should...... be kept as low as possible to increase the power conversion efficiency and increase the reliability of converters. The dynamic performance of the proposed controller is investigated by simulations and experiments....

  7. Accurate Sliding-Mode Control System Modeling for Buck Converters

    DEFF Research Database (Denmark)

    Høyerby, Mikkel Christian Wendelboe; Andersen, Michael Andreas E.

    2007-01-01

    This paper shows that classical sliding mode theory fails to correctly predict the output impedance of the highly useful sliding mode PID compensated buck converter. The reason for this is identified as the assumption of the sliding variable being held at zero during sliding mode, effectively mod...... approach also predicts the self-oscillating switching action of the sliding-mode control system correctly. Analytical findings are verified by simulation as well as experimentally in a 10-30V/3A buck converter....

  8. Grid converters for photovoltaic and wind power systems

    CERN Document Server

    Teodorescu, Remus; Rodríguez, Pedro

    2011-01-01

    "Grid Converters for Photovoltaic and Wind Power Systems provides a comprehensive description of the control of grid converters for photovoltaic and wind power systems. The authors present a range of control methods for meeting the latest application, power quality and power conversion requirements and standards, as well as looking towards potential future control functions. Practical examples, exercises, and an accompanying website with simulation models using Matlab and Simulink environments, and PSIM software make this text a pragmatic resource for electrical engineers as well as students taking related courses"--

  9. Image-converter streak cameras with very high gain

    International Nuclear Information System (INIS)

    1975-01-01

    A new camera is described with slit scanning and very high photonic gain (G=5000). Development of the technology of tubes and microchannel plates has enabled integration of such an amplifying element in an image converter tube which does away with the couplings and the intermediary electron-photon-electron conversions of the classical converter systems having external amplification. It is thus possible to obtain equal or superior performance while retaining considerable gain for the camera, great compactness, great flexibility in use, and easy handling. (author)

  10. Some researches on converting a C++ software to java

    International Nuclear Information System (INIS)

    Ding Yuzheng; Wang Taijie; Dai Guiliang

    1997-01-01

    Because of Java's flexibility, portability, and relative simplicity, Java programming language has sparked considerable interest among software developers. The author presents the experience on converting a C++ off-line software prototype to Java. Some benefits of Java while converting the C++ prototype to Java and also some limitations of Java are described. Some of these limitations arise from the differences between Java and C++, Others are due to weakness of Java itself. The article also introduces some methods to work around Java's limitations

  11. A multioutput LLC-type parallel resonant converter

    Science.gov (United States)

    Liu, Rui; Lee, C. Q.; Upadhyay, Anand K.

    1992-07-01

    When an LLC-type parallel resonant converter (LLC-PRC) operates above resonant frequency, the switching transistors can be turned off at zero voltage. Further study reveals that the LLC-PRC possesses the advantage of lower converter voltage gain as compared with the conventional PRC. Based on analytic results, a complete set of design curves is obtained, from which a systematic design procedure is developed. Experimental results from a 150 W 150 kHz multioutput LLC-type PRC power supply are presented.

  12. Low dose failures of hardened DC-DC power converters

    Science.gov (United States)

    Lehman, J.; Yui, C.; Rax, B. G.; Miyahira, T. F.; Weideman, M.; Schrick, P.; Swift, G. M.; Johnston, A. H.

    2002-01-01

    Box-level total dose testing of the FOG (Fiber Optic Gyro) by IXSEA at ESA's GammabeamFacility were abruptly terminated at 8krad (Si) due to catastrophic failure (complete shutdown). This was unexpected because all components within the gyro were supposedly radiation tolerant. Further testing showed that the components responsible for the failure were two DC-DC converters, manufactured by Interpoint, that stopped regulating shortly before shutdown. This paper summarizes diagnostic test results for the converters to determine the underlying cause of the unexpected failure at low levels of radiation.

  13. Angiotensin-converting enzyme inhibition in diabetic nephropathy

    DEFF Research Database (Denmark)

    Parving, H H; Rossing, P; Hommel, E

    1995-01-01

    The aim of our prospective study was to evaluate putative progression promoters, kidney function, and prognosis during long-term treatment with angiotensin-converting enzyme inhibition in insulin-dependent diabetes mellitus patients suffering from diabetic nephropathy. Eighteen consecutive......, albuminuria (geometric mean +/- antilog SE) 982 +/- 1.2 micrograms/min, and GFR 98 +/- 5 mL/min/1.73 m2. Angiotensin-converting enzyme inhibition induced a significant reduction during the whole treatment period of blood pressure (137/85 +/- 3/1 mm Hg; P

  14. Converter target chemistry - A new challenge to radioanalytical chemistry.

    Science.gov (United States)

    Choudhury, Dibyasree; Lahiri, Susanta

    2018-03-10

    The 1-2 GeV proton induced spallation reaction on the high Z materials like Hg, or lead bismuth eutectic (LBE), popularly known as converter targets, will produce strong flux of fast neutrons which would further react with fissile materials to produce intense radioactive ion beam (RIB). LBE offers suitability for use as converters over Hg but it suffers from the demerit of radiotoxic polonium production. These targets may be viewed as a store house of clinically important and other exotic radionuclides. For application of those radionuclides, radiochemical separation from bulk target material is of utmost importance. Copyright © 2018 Elsevier Ltd. All rights reserved.

  15. Single-Phase Direct Boost AC-AC Converter

    Directory of Open Access Journals (Sweden)

    URSARU, O.

    2017-11-01

    Full Text Available This paper introduces and studies a boost AC-AC converter circuit that can be used to supply power to the 220V receivers in the 110V grids or to increase and adjust voltage at the end of long lines. High frequency AC-AC converters have better specifications than alternative voltage phase control drives with thyristors or TRIACs. When frequency exceeds 20kHz, noise is eliminated, filters are smaller and efficiency is higher. The current waveform is much better, the output voltage can be higher than the input voltage and voltage control is more accurate.

  16. Resonant power converter comprising adaptive dead-time control

    DEFF Research Database (Denmark)

    2017-01-01

    The invention relates in a first aspect to a resonant power converter comprising: a first power supply rail for receipt of a positive DC supply voltage and a second power supply rail for receipt of a negative DC supply voltage. The resonant power converter comprises a resonant network with an input...... terminal for receipt of a resonant input voltage from a driver circuit. The driver circuit is configured for alternatingly pulling the resonant input voltage towards the positive and negative DC supply voltages via first and second semiconductor switches, respectively, separated by intervening dead...

  17. Wave to wire power maximisation from a wave energy converter

    OpenAIRE

    O'Sullivan, Adrian C. M.; Lightbody, Gordon

    2015-01-01

    In this paper a back-to-back voltage source converter controlled linear permanent magnet generator (LPMG) is utilised as the power take off (PTO) for a point absorber wave energy converter system (WEC). It is shown that reactive control which seems promising when an ideal PTO is assumed, is actually infeasible with a real PTO as the electrical losses of the LPMG are excessive when the wave frequency is lower than the natural frequency. A Zero Order Hold (ZOH) and First Order Hold (FOH) Model ...

  18. Quasi-Y-Source Boost DC–DC Converter

    DEFF Research Database (Denmark)

    Siwakoti, Yam Prasad; Blaabjerg, Frede; Loh, Poh Chiang

    2015-01-01

    In this letter, a new topology called “quasi-Y-source dc-dc converter” is presented. It inherits all the advantages of the original Y-source converter. In addition, the new topology draws a continuous current from the source, which is definitely more appropriate for most renewable sources. It als...... has dc-current-blocking capacitors, which will definitely help to prevent the coupled inductor core from saturation. Experimental testing has proven the validity of the proposed network and its application as a high boost dc-dc converter....

  19. A TECHNIQUE OF EXPERIMENTAL INVESTIGATIONS OF LINEAR IMPULSE ELECTROMECHANICAL CONVERTERS

    Directory of Open Access Journals (Sweden)

    V.F. Bolyukh

    2017-04-01

    Full Text Available Purpose. Development of a technique of experimental studies linear pulse electromechanical converters parameters, which are used as shock-power devices and electromechanical accelerators, and comparing the experimental results with the calculated indices obtained using the mathematical model. Methodology. Method of experimental investigations of linear electromechanical converter is that the electrical parameters are recorded simultaneously (inductor winding current and mechanical parameters characterizing the power and speed indicators of the joke with actuator. Power indicators are primarily important for shock-power devices, and high velocity - for electromechanical accelerators. Power indices were investigated using piezoelectric sensors, a system of strain sensors, pressure pulsation sensor and high-speed videorecording. Velocity indicators were investigated using a resistive movement sensor which allows to record character of the armature movement with actuating element in each moment. Results. The technique of experimental research, which is the simultaneous recording of electrical and mechanical power and velocity parameters of the linear electromechanical converter pulse, is developed. In the converter as a shock-power device power indicators are recorded using a piezoelectric transducer, strain sensors system, pressure pulsation sensor and high-speed video. The parameters of the inductor winding current pulse, the time lag of mechanical processes in relation to the time of occurrence of the inductor winding current, the average speed of the joke, the magnitude and momentum of electrodynamics forces acting on the plate strikes are experimentally determined. In the converter as an electromechanical accelerator velocity performance recorded using resistive displacement sensors. It is shown that electromechanical converter processes have complex spatial-temporal character. The experimental results are in good agreement with the calculated

  20. High Voltage Power Converter for Large Wind Turbine

    DEFF Research Database (Denmark)

    Sztykiel, Michal

    system operates at 20 kV level - identical as for the collector distribution network. Medium voltage operation allows the converter unit along with the filter to be installed on the base platform inside the tower. In this manner, more space in the nacelle can be flexibly accommodated by the mechanical...... performance has been achieved by the transformer-less turbine with a back-to-back modular multilevel converter (MMC) topology, which is single grounded only through its DC link common-mode point. It has also occurred that the results derived from losses and short circuit analyses have become advantageous over...

  1. Current Control of Grid Converters Connected with Series AC Capacitor

    DEFF Research Database (Denmark)

    Wang, Xiongfei; Blaabjerg, Frede; Loh, Poh Chiang

    2015-01-01

    The series ac capacitor has recently been used with the transformerless grid-connected converters in the distribution power grids. The capacitive characteristic of the resulting series LC filter restricts the use of conventional synchronous integral or stationary resonant current controllers. Thus...... this paper proposes a fourth-order resonant controller in the stationary frame, which guarantees a zero steady-state current tracking error for the grid converters with series LC filter. This method is then implemented in a three-phase experimental system for verification, where the current harmonics below...

  2. Trends in the wide web converting markets for UV curing

    International Nuclear Information System (INIS)

    Fisher, R.

    1999-01-01

    As we prepare to enter a new decade, the use of ultraviolet (UV) energy to initiate the polymerization of coatings in the wide web segment of the Converting industry continues to increase. As is typical in the Converting industry, while many of the significant advances in technology have been developed around the world, they have been driven initially by the Western European markets. This was true with regards to the introduction of water-borne Pressure Sensitive Adhesives and thermal curing 100% solids silicone release coatings during the late 1970s and early 1980s, but this trend has changed with regards to the current state-of-the-art in UV curing

  3. Method for converting sucrose to .beta.-D-glucose

    Science.gov (United States)

    Simmons, Blake A [San Francisco, CA; Volponi, Joanne V [Livermore, CA; Ingersoll, David [Albuquerque, NM; Walker, Andrew [Woodinville, WA

    2009-07-07

    Disclosed is an apparatus and method for continuously converting sucrose to .beta.-D-glucose. The method comprises a three-stage enzymatic reactor in which an aqueous solution of sucrose is first converted into a solution of fructose and .alpha.-D-glucose by passing it through a porous, packed column containing an inert media on which invertase is immobilized. This solution is then sent through a second packed column containing glucose isomerase and finally a third packed column containing mutarotase. Solution temperature and pH are adjusted to maximize glucose output.

  4. Utilization of non-linear converters for audio amplification

    DEFF Research Database (Denmark)

    Iversen, Niels Elkjær; Birch, Thomas; Knott, Arnold

    2012-01-01

    Class D amplifiers fits the automotive demands quite well. The traditional buck-based amplifier has reduced both the cost and size of amplifiers. However the buck topology is not without its limitations. The maximum peak AC output voltage produced by the power stage is only equal the supply voltage....... The introduction of non-linear converters for audio amplification defeats this limitation. A Cuk converter, designed to deliver an AC peak output voltage twice the supply voltage, is presented in this paper. A 3V prototype has been developed to prove the concept. The prototype shows that it is possible to achieve...

  5. Matrix converter controlled with the direct transfer function approach

    DEFF Research Database (Denmark)

    Rodriguez, J.; Silva, E.; Blaabjerg, Frede

    2005-01-01

    Power electronics is an emerging technology. New power circuits are invented and have to be introduced into the power electronics curriculum. One of the interesting new circuits is the matrix converter (MC), and this paper analyses its working principles. A simple model is proposed to represent...... the power circuit, including the input filter. The power semiconductors are modelled as ideal bidirectional switches and the MC is controlled using a direct transfer function approach. The modulation strategy of the converter is explained in a complete and clear form. The commutation problem of two switches...

  6. Single stage grid converters for battery energy storage

    DEFF Research Database (Denmark)

    Trintis, Ionut; Munk-Nielsen, Stig; Teodorescu, Remus

    2010-01-01

    Integration of renewable energy systems in the power system network such as wind and solar is still a challenge in our days. Energy storage systems (ESS) can overcome the disadvantage of volatile generation of the renewable energy sources. This paper presents power converters for battery energy...... storage systems (BESS) which can interface mediumvoltage batteries to the grid. Converter topologies comparison is performed in terms of efficiency, common mode voltage and redundancy for a 6kV series connected medium voltage batteries with a nominal power of 5MVA to act as a battery charger/discharger....

  7. Acceleration experienced by thermal converter implanted in calves

    International Nuclear Information System (INIS)

    Koshino, I.; Sukalac, R.; Jacobs, G.; Kiraly, R.J.; Nose, Y.

    1976-02-01

    The objective of this study was to determine acceleration levels experienced by the ERDA thermal converter unit implanted abdominally in a calf. A full-scale weighted mock-up of the thermal converter was fabricated containing a triaxial accelerometer. The mock-up was implanted in calf cadavers which were subjected to falls from an operating table. Highest acceleration recorded was 34 g. The mock-up was implanted in living animals and acceleration measurements made under various maneuvers including walking, standing from a laying position, walking up and down stairs, jumping, and falling from a standing position. Maximum acceleration recorded was 8 g and occurred in the falling maneuver

  8. Distributed Generation Using Indirect Matrix Converter in Reverse Power Mode

    DEFF Research Database (Denmark)

    Liu, Xiong; Chiang Loh, Poh; Wang, Peng

    2013-01-01

    not appropriate. Like most power converters, the operation of the IMC can surely be reversed to produce a boosted gain, but so far its relevant control principles have not been discussed. These challenges are now addressed in this paper with distributed generation suggested as a potential application. Simulation......Indirect matrix converter (IMC) is an alternative for ac/ac energy conversion, usually operated with a voltage stepped-down gain of only 0.866. For applications like distribution generation where voltage-boost functionality is required, the traditional style of operating the IMC is therefore...

  9. Digital coherent receiver employing photonic downconversion for phase modulated radio-over-fibre links

    DEFF Research Database (Denmark)

    Zibar, Darko; Caballero Jambrina, Antonio; Guerrero Gonzalez, Neil

    2009-01-01

    A digital coherent receiver employing photonic downconversion is presented and experimentally demonstrated for phase-modulated radio-over-fibre optical links. The receiver is capable of operating at frequencies exceeding the bandwidth of electrical analog-to-digital converter by using photonic...... downconversion to translate the high-frequency input RF signal to the operating frequency range of the analog-to-digital converter. First, using linear digital demodulation scheme we measure SFDR of the link at microwave frequency of 5 GHz. Thereafter, successful signal demodulation of 50 Mbit/s binary phase...... shift keying (BPSK) modulated data signal at 5 GHz RF carrier frequency is experimentally demonstrated by using an analog-to-digital converter with only 1 GHz bandwidth. We successfully demonstrate signal demodulation, using the proposed digital coherent receiver with photonic downconversion, after 40...

  10. [Isolation and study of azobenzene converting soil bacteria].

    Science.gov (United States)

    Vakkerov-Kouzova, N D

    2005-01-01

    Heterotrophic bacteria were isolated from soil and glass slides and classified as Bacillus cereus SNK12, Paenibacillus polymyxa SNK2, Azotobacter chroococcum ANKII, and Ochrobacterium intermedium ANKI. Their cultures could degrade azobenzene under the conditions of co-metabolism. A rapid test for the ability of bacteria to convert azobenzenes is proposed.

  11. Active power decoupling with reduced converter stress for single ...

    Indian Academy of Sciences (India)

    Single-phase DC–AC power electronic converters suffer from pulsating power at double the line frequency. The commonest practice to handle the issue is to provide a huge electrolytic capacitor for smoothening out the ripple. However, the electrolytic capacitors having short end of lifetime limit the overall lifetime of the ...

  12. submitter Test strategies for industrial testers for converter controls equipment

    CERN Document Server

    Oleniuk, P; Kasampalis, V; Nisbet, D; Todd, B; Uznański, S

    2017-01-01

    Power converters and their controls electronics are key elements for the operation of the CERN accelerator complex, having a direct impact on its availability. To prevent early-life failures and provide means to verify electronics, a set of industrial testers is used throughout the converters controls electronics' life cycle. The roles of the testers are to validate mass production during the manufacturing phase and to provide means to diagnose and repair failed modules that are brought back from operation. In the converter controls electronics section of the power converters group in the technology department of CERN (TE/EPC/CCE), two main test platforms have been adopted: a PXI platform for mixed analogue-digital functional tests and a JTAG Boundary-Scan platform for digital interconnection and functional tests. Depending on the functionality of the device under test, the appropriate test platforms are chosen. This paper is a follow-up to results presented at the TWEPP 2015 conference, adding the boundary s...

  13. Test strategies for industrial testers for converter controls equipment

    International Nuclear Information System (INIS)

    Oleniuk, P.; Kasampalis, V.; Cosmo, M. Di; Nisbet, D.; Todd, B.; Uznański, S.

    2017-01-01

    Power converters and their controls electronics are key elements for the operation of the CERN accelerator complex, having a direct impact on its availability. To prevent early-life failures and provide means to verify electronics, a set of industrial testers is used throughout the converters controls electronics' life cycle. The roles of the testers are to validate mass production during the manufacturing phase and to provide means to diagnose and repair failed modules that are brought back from operation. In the converter controls electronics section of the power converters group in the technology department of CERN (TE/EPC/CCE), two main test platforms have been adopted: a PXI platform for mixed analogue-digital functional tests and a JTAG Boundary-Scan platform for digital interconnection and functional tests. Depending on the functionality of the device under test, the appropriate test platforms are chosen. This paper is a follow-up to results presented at the TWEPP 2015 conference, adding the boundary scan test platform and the first results from exploitation of the test system. This paper reports on the test software, hardware design and test strategy applied for a number of devices that has resulted in maximizing test coverage and minimizing test design effort.

  14. Renovating the excitation circuit of a conventional welding converter

    Indian Academy of Sciences (India)

    This paper presents two different new excitation current supplies based on power electronics for an existing conventional welding converter. The proposed circuits are simulated using Lab-VIEW 1200 AI and a PC based system. In the expressions for winding currents the dynamic inductances are used to take into account ...

  15. A nine-level hybrid symmetric cascaded multilevel converter for ...

    Indian Academy of Sciences (India)

    Indrajit Sarkar

    To address these limitations, a nine-level hybrid sym- metric cascaded converter using one five-level and one three-level HB power cell per phase is proposed in this work for induction motor drive applications. The features of proposed configuration are as follows: (a) increase in output voltage levels to nearly double of that ...

  16. Renovating the excitation circuit of a conventional welding converter

    Indian Academy of Sciences (India)

    based on power electronics for an existing conventional welding converter. The proposed circuits are .... The control board consists of a star-delta switch for starting the motor, safety fuses. (F1, F2), a four-position ..... Eng. Handbook 1985 Electrical engineering handbook (New York: John Wiley & Sons). Klingman D 1998 ...

  17. Communication between a Matrix Converter Modulator and a Superset Regulator

    Directory of Open Access Journals (Sweden)

    P. Pošta

    2008-01-01

    Full Text Available This work deals with the modulator of a matrix converter and its communication with the superset regulator. A switching algorithm is briefly introduced. The input voltage measurement method is presented. In the last part of the paper, the testing of communication between the superset regulator and the modulator in FPGA technology are also presented. 

  18. A novel loss reduced modulation strategy for matrix converters

    DEFF Research Database (Denmark)

    Helle, Lars; Munk-Nielsen, Stig

    2001-01-01

    This paper presents a new modulation strategy for three-phase to three-phase matrix converters. The new modulation strategy is applicable whenever the output voltage reference is below half the input voltage. By applying this new modulation method, the switching losses are reduced by 15-35% compa...

  19. Angiotensin-converting enzyme insertion/deletion polymorphism ...

    African Journals Online (AJOL)

    Background: The angiotensin-converting enzyme (ACE) I/D polymorphism has been reported to be associated with Kawasaki disease(KD) ,but studies to date present conflicting results. Objectives: The aim of this study is to derive a more precise estimation of the association between the ACE I/D polymorphism and KD risk.

  20. Using two-chamber photoplasma for creating photovoltaic converter

    Science.gov (United States)

    Astashkevich, S. A.; Bogdanov, E. A.; Kirsanov, G. V.; Kudryavtsev, A. A.

    2017-11-01

    Two-chamber photoplasma is developed for study photovoltaic converters. 2D simulation of conical geometry (similar to one of a solar collector) photoplasma parameters for Na-Ar gas mixture was fulfilled. The present study shows strong spatial non-uniformity of electron density and the electric potential distributions in the two-chamber cell that provides notable value of photo-emf.