WorldWideScience

Sample records for amorphous polymer field-effect

  1. Directionally Aligned Amorphous Polymer Chains via Electrohydrodynamic-Jet Printing: Analysis of Morphology and Polymer Field-Effect Transistor Characteristics.

    Science.gov (United States)

    Kim, Yebyeol; Bae, Jaehyun; Song, Hyun Woo; An, Tae Kyu; Kim, Se Hyun; Kim, Yun-Hi; Park, Chan Eon

    2017-11-15

    Electrohydrodynamic-jet (EHD-jet) printing provides an opportunity to directly assembled amorphous polymer chains in the printed pattern. Herein, an EHD-jet printed amorphous polymer was employed as the active layer for fabrication of organic field-effect transistors (OFETs). Under optimized conditions, the field-effect mobility (μ FET ) of the EHD-jet printed OFETs was 5 times higher than the highest μ FET observed in the spin-coated OFETs, and this improvement was achieved without the use of complex surface templating or additional pre- or post-deposition processing. As the chain alignment can be affected by the surface energy of the dielectric layer in EHD-jet printed OFETs, dielectric layers with varying wettability were examined. Near-edge X-ray absorption fine structure measurements were performed to compare the amorphous chain alignment in OFET active layers prepared by EHD-jet printing and spin coating.

  2. Unusual photoanisotropic alignment in amorphous azobenzene polymers

    DEFF Research Database (Denmark)

    Ramanujam, P.S.

    2015-01-01

    It is well known that irradiation of azobenzene polymer films between 490 and 530nm results in alignment of molecules perpendicular to the polarization of the incident beam. I have recently found that irradiation of amorphous azobenzene polymers with linearly polarized light at wavelengths between...

  3. 25th Anniversary Article: Organic Field-Effect Transistors: The Path Beyond Amorphous Silicon

    Science.gov (United States)

    Sirringhaus, Henning

    2014-01-01

    Over the past 25 years, organic field-effect transistors (OFETs) have witnessed impressive improvements in materials performance by 3–4 orders of magnitude, and many of the key materials discoveries have been published in Advanced Materials. This includes some of the most recent demonstrations of organic field-effect transistors with performance that clearly exceeds that of benchmark amorphous silicon-based devices. In this article, state-of-the-art in OFETs are reviewed in light of requirements for demanding future applications, in particular active-matrix addressing for flexible organic light-emitting diode (OLED) displays. An overview is provided over both small molecule and conjugated polymer materials for which field-effect mobilities exceeding > 1 cm2 V–1 s–1 have been reported. Current understanding is also reviewed of their charge transport physics that allows reaching such unexpectedly high mobilities in these weakly van der Waals bonded and structurally comparatively disordered materials with a view towards understanding the potential for further improvement in performance in the future. PMID:24443057

  4. Gas Sensors Based on Polymer Field-Effect Transistors

    Directory of Open Access Journals (Sweden)

    Aifeng Lv

    2017-01-01

    Full Text Available This review focuses on polymer field-effect transistor (PFET based gas sensor with polymer as the sensing layer, which interacts with gas analyte and thus induces the change of source-drain current (ΔISD. Dependent on the sensing layer which can be semiconducting polymer, dielectric layer or conducting polymer gate, the PFET sensors can be subdivided into three types. For each type of sensor, we present the molecular structure of sensing polymer, the gas analyte and the sensing performance. Most importantly, we summarize various analyte–polymer interactions, which help to understand the sensing mechanism in the PFET sensors and can provide possible approaches for the sensor fabrication in the future.

  5. Touching polymer chains by organic field-effect transistors.

    Science.gov (United States)

    Shao, Wei; Dong, Huanli; Wang, Zhigang; Hu, Wenping

    2014-09-17

    Organic field-effect transistors (OFETs) are used to directly "touch" the movement and dynamics of polymer chains, and then determine Tg. As a molecular-level probe, the conducting channel of OFETs exhibits several unique advantages: 1) it directly detects the motion and dynamics of polymer chain at Tg; 2) it allows the measurement of size effects in ultrathin polymer films (even down to 6 nm), which bridges the gap in understanding effects between surface and interface. This facile and reliable determination of Tg of polymer films and the understanding of polymer chain dynamics guide a new prospect for OFETs besides their applications in organic electronics and casting new light on the fundamental understanding of the nature of polymer chain dynamics.

  6. High mobility polymer gated organic field effect transistor using zinc ...

    Indian Academy of Sciences (India)

    Mater. Sci., Vol. 37, No. 1, February 2014, pp. 95–99. c Indian Academy of Sciences. High mobility polymer gated organic field effect transistor using zinc phthalocyanine. K R RAJESH. ∗. , V KANNAN, M R KIM, Y S CHAE and J K RHEE. Millimeter- Wave Innovation Technology Research Centre (MINT), Dongguk University,.

  7. Field-effect transistor memories based on ferroelectric polymers

    Science.gov (United States)

    Zhang, Yujia; Wang, Haiyang; Zhang, Lei; Chen, Xiaomeng; Guo, Yu; Sun, Huabin; Li, Yun

    2017-11-01

    Field-effect transistors based on ferroelectrics have attracted intensive interests, because of their non-volatile data retention, rewritability, and non-destructive read-out. In particular, polymeric materials that possess ferroelectric properties are promising for the fabrications of memory devices with high performance, low cost, and large-area manufacturing, by virtue of their good solubility, low-temperature processability, and good chemical stability. In this review, we discuss the material characteristics of ferroelectric polymers, providing an update on the current development of ferroelectric field-effect transistors (Fe-FETs) in non-volatile memory applications. Program supported partially by the NSFC (Nos. 61574074, 61774080), NSFJS (No. BK20170075), and the Open Partnership Joint Projects of NSFC-JSPS Bilateral Joint Research Projects (No. 61511140098).

  8. Air-stable π-conjugated amorphous copolymer field-effect transistors with high mobility of 0.3 cm2/Vs

    DEFF Research Database (Denmark)

    Georgakopoulos, S.; Gu, Y.; Nielsen, Martin Meedom

    2012-01-01

    is indicated by atomic force microscopy, grazing incidence wide angle X-ray scattering, and differential scanning calorimetry data. Nevertheless, fitting transistor data to the Gaussian disorder model gives low energetic disorder of sigma = 48 meV and high prefactor mobility mu(0) = 0.67 cm(2)/Vs. The measured......We have fabricated organic bottom-contact top-gate field-effect transistors with an indenofluorene-phenanthrene co-polymer semiconductor, exhibiting ON/OFF ratio of 10(7) and uncommonly high mobility for an amorphous conjugated polymer of up to 0.3 cm(2)/Vs. Lack of crystallinity in this material...

  9. Molecular modeling of amorphous, non-woven polymer networks.

    Science.gov (United States)

    Krausse, Constantin A; Milek, Theodor; Zahn, Dirk

    2015-10-01

    We outline a simple and efficient approach to generating molecular models of amorphous polymer networks. Similar to established techniques of preparing woven polymer networks from quenching high-temperature molecular simulation runs, we use a molecular dynamics simulations of a generic melt as starting points. This generic melt is however only used to describe parts of the polymers, namely the cross-linker units which positions are adopted from particle positions of the quenched melt. Specific degrees of network connectivity are tuned by geometric criteria for linker-linker connections and by suitable multi-body interaction potentials applied to the generic melt simulations. Using this technique we demonstrate adjusting fourfold linker coordination in amorphous polymer networks comprising 10-20% under-coordinated linkers. Graphical Abstract Molecular modeling of amorphous, non-woven polymer networks.

  10. Radical Polymer Utilization for Interfacial Improvement of Organic Field-Effect Transistors

    Science.gov (United States)

    Sung, Seung Hyun; Bajaj, Nikhil; Rhoads, Jeffrey; Chiu, George; Boudouris, Bryan

    Metal-semiconductor interfacial contact is one of the crucial factors for high-performance organic electronic device applications. In particular, the performance of organic field-effect transistors (OFETs) is critically dependent on the engineering of the interface between the organic semiconductor and the source/drain electrodes. Here, we modulate the performance of pentacene-based OFETs through the inclusion of a specific radical polymer, poly(2,2,6,6-tetramethylpiperidine-1-oxyl methacrylate) (PTMA), at the pentacene-gold electrode interface. Using a simple and fast inkjet printing method, the OFET performance is highly enhanced by the systematic deposition of a thin PTMA layer. The insertion of the radical polymer has an impact on the highly-improved OFET performance due to its redox charge transport ability and the amorphous nature allowing the stable growth of the pentacene. The synergistic effect facilitates the charge injection at the interface of the metal and organic semiconductor, resulting in the highly improved OFET performance. As such, the fundamental insights associated with radical polymers can be widened and their utilization as a highly-improved, low-cost interfacial modifier in myriad organic electronic devices is of great promise.

  11. Top-gate pentacene-based organic field-effect transistor with amorphous rubrene gate insulator

    Science.gov (United States)

    Hiroki, Mizuha; Maeda, Yasutaka; Ohmi, Shun-ichiro

    2018-02-01

    The scaling of organic field-effect transistors (OFETs) is necessary for high-density integration and for this, OFETs with a top-gate configuration are required. There have been several reports of damageless lithography processes for organic semiconductor or insulator layers. However, it is still difficult to fabricate scaled OFETs with a top-gate configuration. In this study, the lift-off process and the device characteristics of the OFETs with a top-gate configuration utilizing an amorphous (α) rubrene gate insulator were investigated. We have confirmed that α-rubrene shows an insulating property, and its extracted linear mobility was 2.5 × 10‑2 cm2/(V·s). The gate length and width were 10 and 60 µm, respectively. From these results, the OFET with a top-gate configuration utilizing an α-rubrene gate insulator is promising for the high-density integration of scaled OFETs.

  12. Structure-Property Relationships of Semiconducting Polymers for Flexible and Durable Polymer Field-Effect Transistors.

    Science.gov (United States)

    Kim, Min Je; Jung, A-Ra; Lee, Myeongjae; Kim, Dongjin; Ro, Suhee; Jin, Seon-Mi; Nguyen, Hieu Dinh; Yang, Jeehye; Lee, Kyung-Koo; Lee, Eunji; Kang, Moon Sung; Kim, Hyunjung; Choi, Jong-Ho; Kim, BongSoo; Cho, Jeong Ho

    2017-11-22

    We report high-performance top-gate bottom-contact flexible polymer field-effect transistors (FETs) fabricated by flow-coating diketopyrrolopyrrole (DPP)-based and naphthalene diimide (NDI)-based polymers (P(DPP2DT-T2), P(DPP2DT-TT), P(DPP2DT-DTT), P(NDI2OD-T2), P(NDI2OD-F2T2), and P(NDI2OD-Se2)) as semiconducting channel materials. All of the polymers displayed good FET characteristics with on/off current ratios exceeding 10 7 . The highest hole mobility of 1.51 cm 2 V -1 s -1 and the highest electron mobility of 0.85 cm 2 V -1 s -1 were obtained from the P(DPP2DT-T2) and P(NDI2OD-Se2) polymer FETs, respectively. The impacts of the polymer structures on the FET performance are well-explained by the interplay between the crystallinity, the tendency of the polymer backbone to adopt an edge-on orientation, and the interconnectivity of polymer fibrils in the film state. Additionally, we demonstrated that all of the flexible polymer-based FETs were highly resistant to tensile stress, with negligible changes in their carrier mobilities and on/off ratios after a bending test. Conclusively, these high-performance, flexible, and durable FETs demonstrate the potential of semiconducting conjugated polymers for use in flexible electronic applications.

  13. High thermal conductivity in electrostatically engineered amorphous polymers

    Science.gov (United States)

    Shanker, Apoorv; Li, Chen; Kim, Gun-Ho; Gidley, David; Pipe, Kevin P.; Kim, Jinsang

    2017-01-01

    High thermal conductivity is critical for many applications of polymers (for example, packaging of light-emitting diodes), in which heat must be dissipated efficiently to maintain the functionality and reliability of a system. Whereas uniaxially extended chain morphology has been shown to significantly enhance thermal conductivity in individual polymer chains and fibers, bulk polymers with coiled and entangled chains have low thermal conductivities (0.1 to 0.4 W m−1 K−1). We demonstrate that systematic ionization of a weak anionic polyelectrolyte, polyacrylic acid (PAA), resulting in extended and stiffened polymer chains with superior packing, can significantly enhance its thermal conductivity. Cross-plane thermal conductivity in spin-cast amorphous films steadily grows with PAA degree of ionization, reaching up to ~1.2 W m−1 K−1, which is on par with that of glass and about six times higher than that of most amorphous polymers, suggesting a new unexplored molecular engineering strategy to achieve high thermal conductivities in amorphous bulk polymers. PMID:28782022

  14. Thermal transitions of the amorphous polymers in wheat straw

    Science.gov (United States)

    Wolfgang Stelte; Craig Clemons; Jens K. Holm; Jesper Ahrenfeldt; Ulrik B. Henriksen; Anand R. Sanadi

    2011-01-01

    The thermal transitions of the amorphous polymers in wheat straw were investigated using dynamic mechanical thermal analysis (DMTA). The study included both natural and solvent extracted wheat straw, in moist (8–9% water content) and dry conditions, and was compared to spruce samples. Under these conditions two transitions arising from the glass transition of lignin...

  15. The sorption induced glass transition in amorphous glassy polymers

    NARCIS (Netherlands)

    van der Vegt, N.F.A.; Wessling, Matthias; Strathmann, H.; Briels, Willem J.

    1999-01-01

    Sorption of CO2 in both the glassy and the rubbery state of an amorphous polyethylenelike polymer was investigated using molecular dynamics simulations. The temperature was chosen such that the system was in its glassy state at low solute concentrations and its rubbery state at large solute

  16. Physical stability of API/polymer-blend amorphous solid dispersions.

    Science.gov (United States)

    Lehmkemper, Kristin; Kyeremateng, Samuel O; Bartels, Mareike; Degenhardt, Matthias; Sadowski, Gabriele

    2018-03-01

    The preparation of amorphous solid dispersions (ASDs) is a well-established strategy for formulating active pharmaceutical ingredients by embedding them in excipients, usually amorphous polymers. Different polymers can be combined for designing ASDs with desired properties like an optimized dissolution behavior. One important criterion for the development of ASD compositions is the physical stability. In this work, the physical stability of API/polymer-blend ASDs was investigated by thermodynamic modeling and stability studies. Amorphous naproxen (NAP) and acetaminophen (APAP) were embedded in blends of hydroxypropyl methylcellulose acetate succinate (HPMCAS) and either poly(vinylpyrrolidone) (PVP) or poly(vinylpyrrolidone-co-vinyl acetate) (PVPVA64). Parameters for modeling the API solubility in the blends and the glass-transition temperature curves of the water-free systems with Perturbed-Chain Statistical Associating Fluid Theory and Kwei equation, respectively, were correlated to experimental data. The phase behavior for standardized storage conditions (0%, 60% and 75% relative humidity (RH)) was predicted and compared to six months-long stability studies. According to modeling and experimental results, the physical stability was reduced with increasing HPMCAS content and increasing RH. This trend was observed for all investigated systems, with both APIs (NAP and APAP) and both polymer blends (PVP/HPMCAS and PVPVA64/HPMCAS). PC-SAFT and the Kwei equation turned out to be suitable tools for modeling and predicting the physical stability of the investigated API/polymer-blends ASDs. Copyright © 2017 Elsevier B.V. All rights reserved.

  17. Magnetoimpedance of cobalt-based amorphous ribbons/polymer composites

    Energy Technology Data Exchange (ETDEWEB)

    Semirov, A.V., E-mail: semirov@mail.ru [Irkutsk State University, Irkutsk (Russian Federation); Derevyanko, M.S.; Bukreev, D.A.; Moiseev, A.A.; Kudryavtsev, V.O. [Irkutsk State University, Irkutsk (Russian Federation); Safronov, A.P. [Ural Federal University, Yekaterinburg (Russian Federation)

    2016-10-01

    The combined influence of the temperature, the elastic tensile stress and the external magnetic field on the total impedance and impedance components were studied for rapidly quenched amorphous Co{sub 75}Fe{sub 5}Si{sub 4}B{sub 16} ribbons. Both as-cast amorphous ribbons and Co{sub 75}Fe{sub 5}Si{sub 4}B{sub 16}/polymer amorphous ribbon based composites were considered. Following polymer coverings were studied: modified rubber solution in o-xylene, solution of butyl methacrylate and methacrylic acid copolymer in isopropanol and solution of polymethylphenylsiloxane resin in toluene. All selected composites showed very good adhesion of the coverings and allowed to provide temperature measurements from 163 K up to 383 K under the applied deforming tensile force up to 30 N. The dependence of the modulus of the impedance and its components on the external magnetic field was influenced by the elastic tensile stresses and was affected by the temperature of the samples. It was shown that maximal sensitivity of the impedance and its components to the external magnetic field was observed at minimal temperature and maximal deforming force depended on the frequency of an alternating current. - Highlights: • Impedance and its components of amorphous Co{sub 75}Fe{sub 5}Si{sub 4}B{sub 16} ribbons were studied. • MI sensitivity to the magnetic field depends on a temperature and a deforming force. • Polymer covering can affect the functional properties of the composite.

  18. Definitions of terms relating to individual macromolecules, macromolecular assemblies, polymer solutions, and amorphous bulk polymers (IUPAC Recommendations 2014)

    Czech Academy of Sciences Publication Activity Database

    Stepto, R.; Chang, T.; Kratochvíl, Pavel; Hess, M.; Horie, K.; Sato, T.; Vohlídal, J.

    2015-01-01

    Roč. 87, č. 1 (2015), s. 71-120 ISSN 0033-4545 Institutional support: RVO:61389013 Keywords : amorphous polymers * bulk polymers * IUPAC Polymer Division Subject RIV: CD - Macromolecular Chemistry Impact factor: 2.615, year: 2015

  19. Field effect transistor based on light-emitting polymers and its integration with light-emitting diode

    Science.gov (United States)

    Meng, Hsin-Fei; Horng, Sheng-Fu

    2003-03-01

    Field-effect transistors based on poly(2-methoxy-5(2'-ethyl-hexyloxy)-1,4-phenylene vinylene) (MEH-PPV) and other light-emitting conjugated polymers are fabricated on glass for easy integration with polymer LED. In the integrated device the polymer LED (pixel) and its driving transistor share the same polymer layer as their active semiconductor, with much simplified structures. Despite of the amorphous nature of the polymer film, the transistors can supply up to one micro Ampere of electric current and can be operated under gate modulation of 1 kHz. The hole mobility along the source/drain channel parallel to the glass substrate is found to be 100-1000 times larger than the perpendicular mobility for transport in the sandwich structures, presumably due to the extended chain conformation in spin-coated films. The molecular weight of the polymers is identified as an important factor for the carrier mobility and characteristics of the transistors.

  20. High mobility polymer gated organic field effect transistor using zinc ...

    Indian Academy of Sciences (India)

    Organic semiconductor; field effect transistor; phthalocyanine; high mobility. Abstract. Organic thin film transistors were fabricated using evaporated zinc phthalocyanine as the active layer. Parylene film prepared by chemical vapour deposition was used as the organic gate insulator. The annealing of the samples was ...

  1. Characterization of amorphous multilayered ZnO-SnO2 heterostructure thin films and their field effect electronic properties

    International Nuclear Information System (INIS)

    Lee, Su-Jae; Hwang, Chi-Sun; Pi, Jae-Eun; Yang, Jong-Heon; Oh, Himchan; Cho, Sung Haeng; Cho, Kyoung-Ik; Chu, Hye Yong

    2014-01-01

    Multilayered ZnO-SnO 2 heterostructure thin films were produced using pulsed laser ablation of pie-shaped ZnO-SnO 2 oxides target, and their structural and field effect electronic transport properties were investigated as a function of the thickness of the ZnO and SnO 2 layers. The films have an amorphous multilayered heterostructure composed of the periodic stacking of the ZnO and SnO 2 layers. The field effect electronic properties of amorphous multilayered ZnO-SnO 2 heterostructure thin film transistors (TFTs) are highly dependent on the thickness of the ZnO and SnO 2 layers. The highest electron mobility of 37 cm 2 /V s, a low subthreshold swing of a 0.19 V/decade, a threshold voltage of 0.13 V, and a high drain current on-to-off ratio of ∼10 10 obtained for the amorphous multilayered ZnO(1.5 nm)-SnO 2 (1.5 nm) heterostructure TFTs. These results are presumed to be due to the unique electronic structure of an amorphous multilayered ZnO-SnO 2 heterostructure film consisting of ZnO, SnO 2 , and ZnO-SnO 2 interface layers

  2. Amorphous stabilization and dissolution enhancement of amorphous ternary solid dispersions: combination of polymers showing drug-polymer interaction for synergistic effects.

    Science.gov (United States)

    Prasad, Dev; Chauhan, Harsh; Atef, Eman

    2014-11-01

    The purpose of this study was to understand the combined effect of two polymers showing drug-polymer interactions on amorphous stabilization and dissolution enhancement of indomethacin (IND) in amorphous ternary solid dispersions. The mechanism responsible for the enhanced stability and dissolution of IND in amorphous ternary systems was studied by exploring the miscibility and intermolecular interactions between IND and polymers through thermal and spectroscopic analysis. Eudragit E100 and PVP K90 at low concentrations (2.5%-40%, w/w) were used to prepare amorphous binary and ternary solid dispersions by solvent evaporation. Stability results showed that amorphous ternary solid dispersions have better stability compared with amorphous binary solid dispersions. The dissolution of IND from the ternary dispersion was substantially higher than the binary dispersions as well as amorphous drug. Melting point depression of physical mixtures reveals that the drug was miscible in both the polymers; however, greater miscibility was observed in ternary physical mixtures. The IR analysis confirmed intermolecular interactions between IND and individual polymers. These interactions were found to be intact in ternary systems. These results suggest that the combination of two polymers showing drug-polymer interaction offers synergistic enhancement in amorphous stability and dissolution in ternary solid dispersions. © 2014 Wiley Periodicals, Inc. and the American Pharmacists Association.

  3. Device characteristics of polymer dual-gate field-effect transistors

    NARCIS (Netherlands)

    Maddalena, F.; Spijkman, M.; Brondijk, J. J.; Fonteijn, P.; Brouwer, F.; Hummelen, J. C.; de Leeuw, D. M.; Blom, P. W. M.; de Boer, B.

    2008-01-01

    Dual-gate organic field-effect transistors (OFETs) were fabricated by solution processing using different p-type polymer semiconductors and polymer top-dielectric materials on prefabricated substrates with gold source-drain contacts defined by photolithography. The semiconductors and top dielectrics

  4. Field effect measurements on charge carrier mobilities in various polymer-fullerene blend compositions

    NARCIS (Netherlands)

    von Hauff, E; Parisi, J.; Dyakonov, Vladimir

    2006-01-01

    In this study we investigated materials typically used in polymer photovoltaics. Field effect measurements were performed in order to determine the hole mobilities in the conjugated polymer poly(3-hexylthiophene) (P3HT) and the electron mobilities in the methanofullerene[6,6]-phenyl C61-butyric acid

  5. The Influence of Morphology on High-Performance Polymer Field-Effect Transistors

    DEFF Research Database (Denmark)

    Tsao, Hoi Nok; Cho, Don; Andreasen, Jens Wenzel

    2009-01-01

    The influence of molecular packing on the performance of polymer organic field-effect transistors is illustrated in this work. Both close -stacking distance and long-range order are important for achieving high mobilities. By aligning the polymers from solution, long-range order is induced...

  6. Superior electric storage on an amorphous perfluorinated polymer surface

    Science.gov (United States)

    Fukuhara, Mikio; Kuroda, Tomoyuki; Hasegawa, Fumihiko; Sueyoshi, Takashi

    2016-02-01

    Amorphous perfluoroalkenyl vinyl ether polymer devices can store a remarkably powerful electric charge because their surface contains nanometre-sized cavities that are sensitive to the so-called quantum-size effect. With a work function of approximately 10 eV, the devices show a near-vertical line in the Nyquist diagram and a horizontal line near the -90° phase angle in the Bode diagram. Moreover, they have an integrated effect on the surface area for constant current discharging. This effect can be explained by the distributed constant electric circuit with a parallel assembly of nanometre-sized capacitors on a highly insulating polymer. The device can illuminate a red LED light for 3 ms after charging it with 1 mA at 10 V. Further gains might be attained by integrating polymer sheets with a micro-electro mechanical system.

  7. Dielectric breakdown in silica-amorphous polymer nanocomposite films: the role of the polymer matrix.

    Science.gov (United States)

    Grabowski, Christopher A; Fillery, Scott P; Westing, Nicholas M; Chi, Changzai; Meth, Jeffrey S; Durstock, Michael F; Vaia, Richard A

    2013-06-26

    The ultimate energy storage performance of an electrostatic capacitor is determined by the dielectric characteristics of the material separating its conductive electrodes. Polymers are commonly employed due to their processability and high breakdown strength; however, demands for higher energy storage have encouraged investigations of ceramic-polymer composites. Maintaining dielectric strength, and thus minimizing flaw size and heterogeneities, has focused development toward nanocomposite (NC) films; but results lack consistency, potentially due to variations in polymer purity, nanoparticle surface treatments, nanoparticle size, and film morphology. To experimentally establish the dominant factors in broad structure-performance relationships, we compare the dielectric properties for four high-purity amorphous polymer films (polymethyl methacrylate, polystyrene, polyimide, and poly-4-vinylpyridine) incorporating uniformly dispersed silica colloids (up to 45% v/v). Factors known to contribute to premature breakdown-field exclusion and agglomeration-have been mitigated in this experiment to focus on what impact the polymer and polymer-nanoparticle interactions have on breakdown. Our findings indicate that adding colloidal silica to higher breakdown strength amorphous polymers (polymethyl methacrylate and polyimide) causes a reduction in dielectric strength as compared to the neat polymer. Alternatively, low breakdown strength amorphous polymers (poly-4-vinylpyridine and especially polystyrene) with comparable silica dispersion show similar or even improved breakdown strength for 7.5-15% v/v silica. At ∼15% v/v or greater silica content, all the polymer NC films exhibit breakdown at similar electric fields, implying that at these loadings failure becomes independent of polymer matrix and is dominated by silica.

  8. Field-effect Flow Control in Polymer Microchannel Networks

    Science.gov (United States)

    Sniadecki, Nathan; Lee, Cheng S.; Beamesderfer, Mike; DeVoe, Don L.

    2003-01-01

    A new Bio-MEMS electroosmotic flow (EOF) modulator for plastic microchannel networks has been developed. The EOF modulator uses field-effect flow control (FEFC) to adjust the zeta potential at the Parylene C microchannel wall. By setting a differential EOF pumping rate in two of the three microchannels at a T-intersection with EOF modulators, the induced pressure at the intersection generated pumping in the third, field-free microchannel. The EOF modulators are able to change the magnitude and direction of the pressure pumping by inducing either a negative or positive pressure at the intersection. The flow velocity is tracked by neutralized fluorescent microbeads in the microchannels. The proof-of-concept of the EOF modulator described here may be applied to complex plastic ,microchannel networks where individual microchannel flow rates are addressable by localized induced-pressure pumping.

  9. Thermal transitions of the amorphous polymers in wheat straw

    DEFF Research Database (Denmark)

    Stelte, Wolfgang; Clemons, Craig; Holm, Jens K.

    2011-01-01

    The thermal transitions of the amorphous polymers in wheat straw were investigated using dynamic mechanical thermal analysis (DMTA). The study included both natural and solvent extracted wheat straw, in moist (8–9% water content) and dry conditions, and was compared to spruce samples. Under...... these conditions two transitions arising from the glass transition of lignin and hemicelluloses have been identified. Key transitions attributed to softening of lignin were found at 53, 63 and 91 °C for moist samples of wheat straw, extracted straw and spruce, respectively. Transitions for hemicelluloses were...

  10. Dithiopheneindenofluorene (TIF) Semiconducting Polymers with Very High Mobility in Field-Effect Transistors

    KAUST Repository

    Chen, Hu

    2017-07-19

    The charge-carrier mobility of organic semiconducting polymers is known to be enhanced when the energetic disorder of the polymer is minimized. Fused, planar aromatic ring structures contribute to reducing the polymer conformational disorder, as demonstrated by polymers containing the indacenodithiophene (IDT) repeat unit, which have both a low Urbach energy and a high mobility in thin-film-transistor (TFT) devices. Expanding on this design motif, copolymers containing the dithiopheneindenofluorene repeat unit are synthesized, which extends the fused aromatic structure with two additional phenyl rings, further rigidifying the polymer backbone. A range of copolymers are prepared and their electrical properties and thin-film morphology evaluated, with the co-benzothiadiazole polymer having a twofold increase in hole mobility when compared to the IDT analog, reaching values of almost 3 cm2 V−1 s−1 in bottom-gate top-contact organic field-effect transistors.

  11. Microstructure-mobility correlation in self-organised, conjugated polymer field-effect transistors

    DEFF Research Database (Denmark)

    Sirringhaus, H.; Brown, P.J.; Friend, R.H.

    2000-01-01

    We have investigated the correlation between polymer microstructure and charge carrier mobility in high-mobility, self-organised field-effect transistors of poly-3-hexyl-thiophene (P3HT). Two different preferential orientations of the microcrystalline P3HT domains with respect to the substrate have...

  12. Initial Drug Dissolution from Amorphous Solid Dispersions Controlled by Polymer Dissolution and Drug-Polymer Interaction.

    Science.gov (United States)

    Chen, Yuejie; Wang, Shujing; Wang, Shan; Liu, Chengyu; Su, Ching; Hageman, Michael; Hussain, Munir; Haskell, Roy; Stefanski, Kevin; Qian, Feng

    2016-10-01

    To identify the key formulation factors controlling the initial drug and polymer dissolution rates from an amorphous solid dispersion (ASD). Ketoconazole (KTZ) ASDs using PVP, PVP-VA, HMPC, or HPMC-AS as polymeric matrix were prepared. For each drug-polymer system, two types of formulations with the same composition were prepared: 1. Spray dried dispersion (SDD) that is homogenous at molecular level, 2. Physical blend of SDD (80% drug loading) and pure polymer (SDD-PB) that is homogenous only at powder level. Flory-Huggins interaction parameters (χ) between KTZ and the four polymers were obtained by Flory-Huggins model fitting. Solution (13)C NMR and FT-IR were conducted to investigate the specific drug-polymer interaction in the solution and solid state, respectively. Intrinsic dissolution of both the drug and the polymer from ASDs were studied using a Higuchi style intrinsic dissolution apparatus. PXRD and confocal Raman microscopy were used to confirm the absence of drug crystallinity on the tablet surface before and after dissolution study. In solid state, KTZ is completely miscible with PVP, PVP-VA, or HPMC-AS, demonstrated by the negative χ values of -0.36, -0.46, -1.68, respectively; while is poorly miscible with HPMC shown by a positive χ value of 0.23. According to solution (13)C NMR and FT-IR studies, KTZ interacts with HPMC-AS strongly through H-bonding and dipole induced interaction; with PVPs and PVP-VA moderately through dipole-induced interactions; and with HPMC weakly without detectable attractive interaction. Furthermore, the "apparent" strength of drug-polymer interaction, measured by the extent of peak shift on NMR or FT-IR spectra, increases with the increasing number of interacting drug-polymer pairs. For ASDs with the presence of considerable drug-polymer interactions, such as KTZ/PVPs, KTZ/PVP-VA, or KTZ /HPMC-AS systems, drug released at the same rate as the polymer when intimate drug-polymer mixing was ensured (i.e., the SDD systems

  13. Vinyl Flanked Difluorobenzothiadiazole-Dithiophene Conjugated Polymer for High Performance Organic Field-Effect Transistors.

    Energy Technology Data Exchange (ETDEWEB)

    Liang, Xianfeng; Sun, Wandong; Chen, Yanlin; Tan, Luxi; Cai, Zheng-Xu; Liu, Zitong; Wang, Lin; Li, Jing; Chen, Wei; Dong, Lichun

    2018-02-21

    Fluorine containing conjugated polymers have been widely applied in high performance organic solar cells, but their use in field-effect transistors is still quite limited. In this work, a conjugated polymer PTFBTV based on difluorobenzothiadiazole (DFBT) and dithiophene was synthesized, utilizing multiple vinylene as linkers. The polymer exhibits a relatively high hole mobility up to 2.0 cm(2) V-1 s(-1) compared with the reported DFBT-oligothiophene based polymers, yet its structural complexity is much simpler. The polymer thin film exhibits a typical 'face on' molecular orientation. A single crystal of its monomer revealed a non-covalent intramolecular contact between fluorine and the neighbouring proton, which strengthens the backbone co-planarity. Meanwhile an intermolecular F...F contact was also observed, which might cause rather scattered lamellar crystallinity for PTFBTV in the solid state.

  14. Chemical oxidative and solid state synthesis of low molecular weight polymers for organic field effect transistors

    Science.gov (United States)

    Mahale, Rajashree Y.; Dharmapurikar, Satej S.; Chini, Mrinmoy Kumar

    2018-03-01

    Solution processability of the precursor molecules is a major issue owing to their limited solubility for the synthesis of conjugated polymers. Therefore, we favour the solvent free solid state chemical oxidative polymerization route for the synthesis of diketopyrrolopyrrole (DPP) based donor-acceptor (D-A) type conjugated polymers. D-A type polymer Poly(S-OD-EDOT) which contains DPP coupled with EDOT donor units is synthesized via solid state polymerization method. The polymer is employed as an active layer for organic field-effect transistors to measure charge transport properties. The Polymer shows good hole mobility 3.1 × 10-2 cm2 V-1 s-1, with a on/off ratio of 1.1 × 103.

  15. Pseudobrush theory of amorphous interphase in semicrystalline polymers.

    Science.gov (United States)

    Milner, Scott

    2009-03-01

    The conformation of polymer chains emerging from the face of a crystalline lamella has long been a matter of dispute. Long ago, arguments pitted ``adjacent reentry'' versus the ``switchboard model'' as extreme limits of possible behavior. Later, two theoretical approaches were attempted, but one (the Gambler's Ruin model) did not properly account for the constraint of melt density, and the other (heuristic configuration counting of Flory et al.) did not account for chain connectivity. These shortcomings are resolved by a new ``pseudobrush'' theory of the amorphous interphase, which represents the reentrant chains as a polydisperse brush of loops in a self-consistent hydrostatic pressure field. This theory predicts the fraction of adjacent reentry, shows how the anisotropy of the interphase dies away with distance, and how the Gambler's Ruin model is recovered far from the interface. Extension to the case of a finite slab between two crystal-melt interfaces predicts the frequency of tie chains, a key parameter for nonlinear deformation and ductile failure of semicrystalline polymers.

  16. Polymer incorporation method affects the physical stability of amorphous indomethacin in aqueous suspension

    DEFF Research Database (Denmark)

    Surwase, S A; Itkonen, L; Aaltonen, J

    2015-01-01

    methylcellulose (HPMC) and Soluplus® (SP)) were used and included in the suspensions either as a solid dispersion (SD) with IND or dissolved in the suspension medium prior to the addition of amorphous IND. The total concentrations of both IND and the polymer in the suspensions were kept the same for both methods......This study reports the potential of different polymers and polymer incorporation methods to inhibit crystallisation and maintain supersaturation of amorphous indomethacin (IND) in aqueous suspensions during storage. Three different polymers (poly(vinyl pyrrolidone) (PVP), hydroxypropyl...... of polymer incorporation. All the polymers (with both incorporation methods) inhibited crystallisation of the amorphous IND. The SDs were better than the predissolved polymer solutions at inhibiting crystallisation. The SDs were also better at maintaining drug supersaturation. SP showed a higher IND...

  17. Applications of interface controlled pulsed-laser deposited polymer films in field-effect transistors

    Science.gov (United States)

    Adil, Danish; Ukah, Ndubuisi; Guha, Suchi; Gupta, Ram; Ghosh, Kartik

    2010-03-01

    Matrix assisted pulsed laser evaporation, a derivative of pulsed laser deposition (PLD), is an alternative method of depositing polymer and biomaterial films that allows homogeneous film coverage of high molecular weight organic materials for layer-by-layer growth without any laser induced damage. Polyfluorene (PF)-based conjugated polymers have attracted considerable attention in organic field-effect transistors (FETs). A co-polymer of PF (PFB) was deposited as a thin film using matrix assisted PLD employing a KrF excimer laser. Electrical characteristics of FETs fabricated using these PLD grown films were compared to those of FETs using spin-coated films. We show that threshold voltages, on/off ratios, and charge carrier motilities are significantly improved in PLD grown films. This is attributed to an improved dielectric-polymer interface.

  18. Quinacridone-Diketopyrrolopyrrole-Based Polymers for Organic Field-Effect Transistors

    Directory of Open Access Journals (Sweden)

    Kazuo Takimiya

    2013-03-01

    Full Text Available Incorporation of pigment or dye molecules as building units is of great interest in the development of semiconducting polymers, due to their strong intermolecular interactions arising from the strong local dipoles in the unit structure, which would facilitate the charge transport property. In this paper, semiconducting polymers based on well-known pigments, namely, quinacridone and diketopyrrolopyrrole, are synthesized and characterized. The π-stacking distances are found to be 3.5–3.8 Å, which is fairly narrow for semiconducting polymers, indicating that they possess strong intermolecular interactions. Interestingly, polymer orientation is influenced by the composition of alkyl side chains. While the edge-on orientation is observed when the linear alkyl groups are introduced for all the side chains, the face-on orientation is observed when the branched alkyl groups are introduced either in the quinacridone or diketopyrrolopyrrole unit. It is found that the electronic structure of the present polymers is mostly affected by that of the diketopyrrolopyrrole unit, as evidenced by the absorption spectra and computation. Although the field-effect mobility of the polymers is modest, i.e., in the order of 10−4–10−3 cm2/Vs, these findings could be important information for the development of semiconducting polymers.

  19. Field Effect Flow Control in a Polymer T-Intersection Microfluidic Network

    Science.gov (United States)

    Sniadecki, Nathan J.; Chang, Richard; Beamesderfer, Mike; Lee, Cheng S.; DeVoe, Don L.

    2003-01-01

    We present a study of induced pressure pumping in a polymer microchannel due to differential electroosmotic flow @OF) rates via field-effect flow control (FEFC). The experimental results demonstrate that the induced pressure pumping is dependent on the distance of the FEFC gate from the cathodic gate. A proposed flow model based on a linearly-decaying zeta potential profile is found to successfully predict experimental trends.

  20. Highly stable organic polymer field-effect transistor sensor for selective detection in the marine environment

    Science.gov (United States)

    Knopfmacher, Oren; Hammock, Mallory L.; Appleton, Anthony L.; Schwartz, Gregor; Mei, Jianguo; Lei, Ting; Pei, Jian; Bao, Zhenan

    2014-01-01

    In recent decades, the susceptibility to degradation in both ambient and aqueous environments has prevented organic electronics from gaining rapid traction for sensing applications. Here we report an organic field-effect transistor sensor that overcomes this barrier using a solution-processable isoindigo-based polymer semiconductor. More importantly, these organic field-effect transistor sensors are stable in both freshwater and seawater environments over extended periods of time. The organic field-effect transistor sensors are further capable of selectively sensing heavy-metal ions in seawater. This discovery has potential for inexpensive, ink-jet printed, and large-scale environmental monitoring devices that can be deployed in areas once thought of as beyond the scope of organic materials.

  1. Free-volume micro-structure of the amorphous polymers at Tg

    International Nuclear Information System (INIS)

    Bartos, J.

    1995-01-01

    The positron annihilation spectroscopy was used to the study of the free-volume microstructure of the amorphous polymers [diene-elastomers, vinyl-elastomers and thermoplastics, aromatic thermoplastics

  2. Benzocyclobutene (BCB) Polymer as Amphibious Buffer Layer for Graphene Field-Effect Transistor.

    Science.gov (United States)

    Wu, Yun; Zou, Jianjun; Huo, Shuai; Lu, Haiyan; Kong, Yuecan; Chen, Tangshen; Wu, Wei; Xu, Jingxia

    2015-08-01

    Owing to the scattering and trapping effects, the interfaces of dielectric/graphene or substrate/graphene can tailor the performance of field-effect transistor (FET). In this letter, the polymer of benzocyclobutene (BCB) was used as an amphibious buffer layer and located at between the layers of substrate and graphene and between the layers of dielectric and graphene. Interestingly, with the help of nonpolar and hydrophobic BCB buffer layer, the large-scale top-gated, chemical vapor deposited (CVD) graphene transistors was prepared on Si/SiO2 substrate, its cutoff frequency (fT) and the maximum cutoff frequency (fmax) of the graphene field-effect transistor (GFET) can be reached at 12 GHz and 11 GHz, respectively.

  3. Top-gate organic field-effect transistors fabricated on shape-memory polymer substrates

    Science.gov (United States)

    Choi, Sangmoo; Fuentes-Hernandez, Canek; Wang, Cheng-Yin; Wei, Andrew; Voit, Walter; Zhang, Yadong; Barlow, Stephen; Marder, Seth R.; Kippelen, Bernard

    2015-08-01

    We demonstrate top-gate organic field-effect transistors (OFETs) with a bilayer gate dielectric and doped contacts fabricated on shape-memory polymer (SMP) substrates. SMPs exhibit large variations in Young's modulus dependent on temperature and have the ability to fix two or more geometric configurations when a proper stimulus is applied. These unique properties make SMPs desirable for three-dimensional shape applications of OFETs. The electrical properties of OFETs on SMP substrates are presented and compared to those of OFETs on traditional glass substrates.

  4. Drug-polymer solubility and miscibility: Stability consideration and practical challenges in amorphous solid dispersion development.

    Science.gov (United States)

    Qian, Feng; Huang, Jun; Hussain, Munir A

    2010-07-01

    Drug-polymer solid dispersion has been demonstrated as a feasible approach to formulate poorly water-soluble drugs in the amorphous form, for the enhancement of dissolution rate and bioperformance. The solubility (for crystalline drug) and miscibility (for amorphous drug) in the polymer are directly related to the stabilization of amorphous drug against crystallization. Therefore, it is important for pharmaceutical scientists to rationally assess solubility and miscibility in order to select the optimal formulation (e.g., polymer type, drug loading, etc.) and recommend storage conditions, with respect to maximizing the physical stability. This commentary attempts to discuss the concepts and implications of the drug-polymer solubility and miscibility on the stabilization of solid dispersions, review recent literatures, and propose some practical strategies for the evaluation and development of such systems utilizing a working diagram. (c) 2010 Wiley-Liss, Inc. and the American Pharmacists Association

  5. The Influence of Crosslink Density on the Failure Behavior in Amorphous Polymers by Molecular Dynamics Simulations

    Directory of Open Access Journals (Sweden)

    Junhua Zhao

    2016-03-01

    Full Text Available The crosslink density plays a key role in the mechanical response of the amorphous polymers in previous experiments. However, the mechanism of the influence is still not clear. In this paper, the influence of crosslink density on the failure behavior under tension and shear in amorphous polymers is systematically studied using molecular dynamics simulations. The present results indicate that the ultimate stresses and the broken ratios (the broken bond number to all polymer chain number ratios increase, as well as the ultimate strains decrease with increasing crosslink density. The strain concentration is clearer with the increase of crosslink density. In other words, a higher crosslink density leads to a higher strain concentration. Hence, the higher strain concentration further reduces the fracture strain. This study implies that the mechanical properties of amorphous polymers can be dominated for different applications by altering the molecular architecture.

  6. Effects of Intercalation on the Hole Mobility of Amorphous Semiconducting Polymer Blends

    KAUST Repository

    Cates, Nichole C.

    2010-06-08

    Fullerenes have been shown to intercalate between the side chains of many crystalline and semicrystalline polymers and to affect the properties of polymer:fullerene bulk heterojunction solar cells. Here we present the first in-depth study of intercalation in an amorphous polymer. We study blends of the widely studied amorphous polymer poly(2-methoxy-5-(3studied amorphous polymer poly(,7·studied amorphous polymer poly(-dimethyloctyloxy)-p-phenylene vinylene) (MDMO-PPV) with a variety of molecules using photoluminescence measurements, scanning electron microscopy, and space-charge limited current mobility measurements. The blends with elevated hole mobilities exhibit complete photoluminescence quenching and show no phase separation in a scanning electron microscope. We conclude that intercalation occurs in MDMO-PPV:fullerene blends and is responsible for the increase in the MDMO-PPV hole mobility by several orders of magnitude when it is blended with fullerenes, despite the dilution of the hole-conducting polymer with an electron acceptor. © 2010 American Chemical Society.

  7. Charge transport behavior of benodithiophene-diketopyrrololpyrrole-based conjugated polymer in organic field-effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Park, Jin Kuen [Dept. of Chemistry, Hankuk University of Foreign Studies, Yongin (Korea, Republic of)

    2015-07-15

    Organic optoelectronic devices, such as light-emitting diodes, organic solar cells (OSCs), and organic field effect transistors (OFETs), have emerged due to the development of π-conjugated polymers. Because the delocalized π-framework can significantly reduce the energy gap between the highest-occupied molecular orbital (HOMO) and the lowest-unoccupied molecular orbital (LUMO), their intrinsic optoelectronic properties can be tunable with their conjugation length in terms of average molecular weights and their π-backbone structures. The new type of low bandgap conjugated polymer (P1) has been successively polymerized via a palladium- catalyzed Stille cross-coupling reaction with bis-ethylhexyl BDT and bis-n-decane DPP. With a linear alkyl chain in the DPP units, the intermolecular packing structure was thought to be enhanced by proving the UV–Vis and UPS spectra. In addition, the electronic properties of P1 via field-effect transistors well illustrate the typical p-type semiconducting property without showing the significant improvement by thermal annealing. From a broader perspective, this research indicates that a wider choice of linear alkyl chain length in DPP units and modification of the interface between dielectric and active layers should be sought to further optimize device performance. Hence, progressive works with the strategy presented in this report will be pursued to address the different challenges in attaining target OFET performances.

  8. The adsorption of surfactant at the amorphous polymer solution interface

    International Nuclear Information System (INIS)

    Gilchrist, Valerie A.

    2001-01-01

    Adsorption of surfactants onto amorphous polymers at the solid-solution interface is of direct relevance to many industrial sectors ranging from food, pharmaceuticals, paints, paper and photographic colour films. Although it is widely accepted that surfactants play the underpinning role in these applications, little is currently understood about the interactions between surfactants and polymeric materials at the molecular level. This lack of progress is mainly due to the inability of most existing techniques in probing this type of structural information at the wet interface. Specular neutron reflection (SNR) is a recently developed technique capable of detecting structural information with resolution down to a few angstroms (A). When combined with deuterium labeling, it is possible to distinguish the surfactant from the polymeric species at the interface. The aim of this work is to explore the appropriate experimental approach that utilizes the potential of neutron reflection to unravel molecular information about the actions of surfactants. A major progress that was made in the project was the -development of experimental protocols for the formation of smooth polymeric thin films onto neutron transparent substrates. This experimental process was substantially supported by spectroscopic ellipsometry (SE), a home-based laboratory optical system that was also highly sensitive to film thickness and composition. This exploratory work has mainly used model polymeric samples that are of broader implications to various technological applications. A nonionic alkyl ethoxylate surfactant, such as C 12 E 5 was chosen because its interfacial behaviour has been widely examined. Measurements were made over a wide concentration range around the critical micellar concentration (cmc), using specially designed cells. In the case of PMMA (poly(methylmethacrylate)), adsorption of C 12 E 5 was found to be completely reversible with no observable penetration of the surfactant into the

  9. Field effect measurements on charge carrier mobilities in various polymer-fullerene blend compositions

    International Nuclear Information System (INIS)

    Hauff, Elizabeth von; Parisi, Juergen; Dyakonov, Vladimir

    2006-01-01

    In this study we investigated materials typically used in polymer photovoltaics. Field effect measurements were performed in order to determine the hole mobilities in the conjugated polymer poly(3-hexylthiophene) (P3HT) and the electron mobilities in the methanofullerene[6,6]-phenyl C 61 -butyric acid methyl ester (PCBM), and, particularly, in the polymer-fullerene composite blends. Regarding the pure films, electron mobilities in PCBM were found to be in the 10 -2 cm 2 /Vs range, and hole mobilities in P3HT were found to be in the 10 -3 cm2/Vs range. In the PCBM:P3HT blends, it was found that varying the PCBM content in PCBM:P3HT blends led to a steep increase in electron mobility with increasing PCBM content, while the hole mobility was found to slightly decrease with the increasing PCBM concentration. In 2:1 PCBM:P3HT tempered blends, the charge carrier mobilities were found to be roughly balanced, at 10 -3 cm 2 /Vs. For improved electron transport in the blends, tempering was found to be crucial

  10. Heterogeneity of spiral wear patterns produced by local heating on amorphous polymers

    International Nuclear Information System (INIS)

    Rice, Reginald H.; Gnecco, Enrico; King, William P.; Szoszkiewicz, Robert

    2013-01-01

    We report on spiral wear patterns produced at constant angular velocity by hot tip atomic force microscopy (HT-AFM) on surfaces of two common amorphous polymers: polystyrene (PS) and polymethylmethacrylate (PMMA). Topography of these patterns is obtained with regular AFM cantilevers. Topography cross-sections taken from a center of each spiral at a given azimuthal angle Θ relate changes of surface corrugation h corr with tangential velocity v of a thermal cantilever. Polymer wear is characterized by a power law h corr (v) = α(v/v max ) −β , which yields a pre-factor α and an exponent β. Below the glass transition temperature T g , α is polymer specific and β varies weakly between similar conditions and samples. Variations of β are hypothesized to reflect polymer relaxation processes, which are expected to vary only weakly between amorphous polymers. At and above T g , α approaches initial thermal tip indentation depth within a polymer, β plummets, and a power law relation of h corr with v diverges. These results are explained by heterogeneous wear around T g due to a local nature of glass transition. At all studied temperatures, additional wear heterogeneities are found as due to position on the polymer and Θ. Variations of α and β with position on the polymer are found to be only marginally larger then uncertainties of the thermal tip–polymer interface temperature. Variations of α and β with Θ are found to be largely influenced by buckling of thermal cantilevers traveling in a spiral pattern. - Graphical abstract: Display Omitted - Highlights: • Novel method to characterize temperature dependant wear on polymers is reported. • Hot-tip AFM methods and spiral scanning are used. • Heterogeneity of polymer wear in vicinity of glass transition is discussed. • Amorphous polymers are studied only

  11. Solvent-mediated amorphous-to-crystalline transformation of nitrendipine in amorphous particle suspensions containing polymers

    DEFF Research Database (Denmark)

    Xia, Dengning; Wu, Jian-Xiong; Cui, Fude

    2012-01-01

    The amorphous-to-crystalline transformation of nitrendipine was investigated using Raman spectroscopy and X-ray powder diffraction (XRPD). The nucleation and growth rate of crystalline nitrendipine in a medium containing poly (vinyl alcohol) (PVA) and polyethylene glycol (PEG 200) were quantitati......The amorphous-to-crystalline transformation of nitrendipine was investigated using Raman spectroscopy and X-ray powder diffraction (XRPD). The nucleation and growth rate of crystalline nitrendipine in a medium containing poly (vinyl alcohol) (PVA) and polyethylene glycol (PEG 200) were...

  12. Photopatternable Conducting Polymer Nanocomposite with Incorporated Gold Nanoparticles for Use in Organic Field Effect Transistors

    Energy Technology Data Exchange (ETDEWEB)

    Huh, Sung; Choi, Hyun Ho; Cho, Kil Won; Kim, Seung Bin [Pohang University of Science and Technology, Pohang (Korea, Republic of)

    2012-04-15

    We investigated a new method for patterning organic field-effect transistors (OFETs) using a photopatternable conducting polymer nanocomposite, consisting of poly(3-hexylthiophene) (P3HT)-coated gold nanoparticles (AuNPs) that had been modified with a photoreactive cinnamate group, to form P3HT-AuNP-CI. We found that the addition of the cinnamate group to the nanoparticle surface assisted the preparation of a solvent resistive semiconducting film and preserved the P3HT ordering, which was interrupted by Au-P3HT interactions, as well as provided UV-controllable electrical properties. The P3HT-AuNPs-CI films could be microscale-patterned via a UV crosslinking photoreaction, represented as a promising photopatternable semiconductor material for use in advanced applications, with tunable electrical properties for fabrication of sub-micron and microscale electronic devices

  13. Hysteresis mechanism and control in pentacene organic field-effect transistors with polymer dielectric

    Directory of Open Access Journals (Sweden)

    Wei Huang

    2013-05-01

    Full Text Available Hysteresis mechanism of pentacene organic field-effect transistors (OFETs with polyvinyl alcohol (PVA and/or polymethyl methacrylate (PMMA dielectrics is studied. Through analyzing the electrical characteristics of OFETs with various PVA/PMMA arrangements, it shows that charge, which is trapped in PVA bulk and at the interface of pentacene/PVA, is one of the origins of hysteresis. The results also show that memory window is proportional to both trap amount in PVA and charge density at the gate/PVA or PVA/pentacene interfaces. Hence, the controllable memory window of around 0 ∼ 10 V can be realized by controlling the thickness and combination of triple-layer polymer dielectrics.

  14. Photopatternable Conducting Polymer Nanocomposite with Incorporated Gold Nanoparticles for Use in Organic Field Effect Transistors

    International Nuclear Information System (INIS)

    Huh, Sung; Choi, Hyun Ho; Cho, Kil Won; Kim, Seung Bin

    2012-01-01

    We investigated a new method for patterning organic field-effect transistors (OFETs) using a photopatternable conducting polymer nanocomposite, consisting of poly(3-hexylthiophene) (P3HT)-coated gold nanoparticles (AuNPs) that had been modified with a photoreactive cinnamate group, to form P3HT-AuNP-CI. We found that the addition of the cinnamate group to the nanoparticle surface assisted the preparation of a solvent resistive semiconducting film and preserved the P3HT ordering, which was interrupted by Au-P3HT interactions, as well as provided UV-controllable electrical properties. The P3HT-AuNPs-CI films could be microscale-patterned via a UV crosslinking photoreaction, represented as a promising photopatternable semiconductor material for use in advanced applications, with tunable electrical properties for fabrication of sub-micron and microscale electronic devices

  15. Modeling the Coupled Chemo-Thermo-Mechanical Behavior of Amorphous Polymer Networks.

    Energy Technology Data Exchange (ETDEWEB)

    Zimmerman, Jonathan A. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Nguyen, Thao D. [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Xiao, Rui [Sandia National Lab. (SNL-CA), Livermore, CA (United States)

    2015-02-01

    Amorphous polymers exhibit a rich landscape of time-dependent behavior including viscoelasticity, structural relaxation, and viscoplasticity. These time-dependent mechanisms can be exploited to achieve shape-memory behavior, which allows the material to store a programmed deformed shape indefinitely and to recover entirely the undeformed shape in response to specific environmental stimulus. The shape-memory performance of amorphous polymers depends on the coordination of multiple physical mechanisms, and considerable opportunities exist to tailor the polymer structure and shape-memory programming procedure to achieve the desired performance. The goal of this project was to use a combination of theoretical, numerical and experimental methods to investigate the effect of shape memory programming, thermo-mechanical properties, and physical and environmental aging on the shape memory performance. Physical and environmental aging occurs during storage and through exposure to solvents, such as water, and can significantly alter the viscoelastic behavior and shape memory behavior of amorphous polymers. This project – executed primarily by Professor Thao Nguyen and Graduate Student Rui Xiao at Johns Hopkins University in support of a DOE/NNSA Presidential Early Career Award in Science and Engineering (PECASE) – developed a theoretical framework for chemothermo- mechanical behavior of amorphous polymers to model the effects of physical aging and solvent-induced environmental factors on their thermoviscoelastic behavior.

  16. Laser Photolytic Approach to Cu/polymer Sols and Cu/polymer Nanocomposites with Amorphous Cu Phase.

    Czech Academy of Sciences Publication Activity Database

    Pola, Josef; Ouchi, A.; Bakardjieva, Snejana; Urbanová, Markéta; Boháček, Jaroslav; Šubrt, Jan

    2007-01-01

    Roč. 192, 2-3 (2007) , s. 84-92 ISSN 1010-6030 Institutional research plan: CEZ:AV0Z40720504; CEZ:AV0Z40320502 Keywords : Cu-polymer nanocomposite * laser solution photolysis * amorphous Cu phase Subject RIV: CH - Nuclear ; Quantum Chemistry Impact factor: 1.911, year: 2007

  17. Enhanced solid-state order and field-effect hole mobility through control of nanoscale polymer aggregation

    KAUST Repository

    Chen, Mark S.

    2013-12-26

    Efficient charge carrier transport in organic field-effect transistors (OFETs) often requires thin films that display long-range order and close π-π packing that is oriented in-plane with the substrate. Although some polymers have achieved high field-effect mobility with such solid-state properties, there are currently few general strategies for controlling the orientation of π-stacking within polymer films. In order to probe structural effects on polymer-packing alignment, furan-containing diketopyrrolopyrrole (DPP) polymers with similar optoelectronic properties were synthesized with either linear hexadecyl or branched 2-butyloctyl side chains. Differences in polymer solubility were observed and attributed to variation in side-chain shape and polymer backbone curvature. Averaged field-effect hole mobilities of the polymers range from 0.19 to 1.82 cm2/V·s, where PDPP3F-C16 is the least soluble polymer and provides the highest maximum mobility of 2.25 cm2/V·s. Analysis of the films by AFM and GIXD reveal that less soluble polymers with linear side chains exhibit larger crystalline domains, pack considerably more closely, and align with a greater preference for in-plane π-π packing. Characterization of the polymer solutions prior to spin-coating shows a correlation between early onset nanoscale aggregation and the formation of films with highly oriented in-plane π-stacking. This effect is further observed when nonsolvent is added to PDPP3F-BO solutions to induce aggregation, which results in films with increased nanostructural order, in-plane π-π orientation, and field-effect hole mobilities. Since nearly all π-conjugated materials may be coaxed to aggregate, this strategy for enhancing solid-state properties and OFET performance has applicability to a wide variety of organic electronic materials. © 2013 American Chemical Society.

  18. Dissolution Performance of High Drug Loading Celecoxib Amorphous Solid Dispersions Formulated with Polymer Combinations.

    Science.gov (United States)

    Xie, Tian; Taylor, Lynne S

    2016-03-01

    The aims of this study were twofold. First, to evaluate the effectiveness of selected polymers in inhibiting solution crystallization of celecoxib. Second, to compare the release rate and crystallization tendency of celecoxib amorphous solid dispersions (ASDs) formulated with a single polymer, or binary polymer combinations. The effectiveness of polymers, polyvinylpyrrolidone (PVP), hydroxypropylmethyl cellulose (HPMC) or HPMC acetate succinate (HPMCAS), in maintaining supersaturation of celecoxib solutions was evaluated by performing nucleation induction time measurements. Crystallization kinetics of ASD suspensions were monitored using Raman spectroscopy. Dissolution experiments were carried out under non-sink conditions. Pure amorphous celecoxib crystallized rapidly through both matrix and solution pathways. Matrix and solution crystallization was inhibited when celecoxib was molecularly mixed with a polymer, resulting in release of the drug to form supersaturated solutions. Cellulosic polymers were more effective than PVP in maintaining supersaturation. Combining a cellulosic polymer and PVP enabled improved drug release and stability to crystallization. Inclusion of an effective solution crystallization inhibitor as a minor component in ternary dispersions resulted in prolonged supersaturation following dissolution. This study shows the feasibility of formulation strategies for ASDs where a major polymer component is used to achieve one key property e.g. release, while a minor polymer component is added to prevent crystallization.

  19. Highly aligned conjugated polymer films prepared by rotation coating for high-performance organic field-effect transistors

    Science.gov (United States)

    Van Tho, Luu; Park, Won-Tae; Choi, Eun-Young; Noh, Yong-Young

    2017-04-01

    Recently, exceptionally high field-effect mobility in organic field-effect transistors (OFETs) has been fabricated using semiconducting films with one-dimensionally aligned, highly planar electron donor-acceptor copolymers, within the channel of transistors. Here, we propose an extremely simple coating method, called rotation coating, for preparing highly aligned, conjugated polymer thin films for applications in various organic electronic devices. We realize highly aligned polymer films using various conjugated polymers and applied the films as active layers for high-performance OFETs. Significantly high field-effect mobility values of 1.45 ± 0.46 cm2/Vs have been achieved for rotation coated diketopyrrolopyrrole-thieno[3,2-b]thiophene copolymer films.

  20. Ambipolar Small-Molecule:Polymer Blend Semiconductors for Solution-Processable Organic Field-Effect Transistors.

    Science.gov (United States)

    Kang, Minji; Hwang, Hansu; Park, Won-Tae; Khim, Dongyoon; Yeo, Jun-Seok; Kim, Yunseul; Kim, Yeon-Ju; Noh, Yong-Young; Kim, Dong-Yu

    2017-01-25

    We report on the fabrication of an organic thin-film semiconductor formed using a blend solution of soluble ambipolar small molecules and an insulating polymer binder that exhibits vertical phase separation and uniform film formation. The semiconductor thin films are produced in a single step from a mixture containing a small molecular semiconductor, namely, quinoidal biselenophene (QBS), and a binder polymer, namely, poly(2-vinylnaphthalene) (PVN). Organic field-effect transistors (OFETs) based on QBS/PVN blend semiconductor are then assembled using top-gate/bottom-contact device configuration, which achieve almost four times higher mobility than the neat QBS semiconductor. Depth profile via secondary ion mass spectrometry and atomic force microscopy images indicate that the QBS domains in the films made from the blend are evenly distributed with a smooth morphology at the bottom of the PVN layer. Bias stress test and variable-temperature measurements on QBS-based OFETs reveal that the QBS/PVN blend semiconductor remarkably reduces the number of trap sites at the gate dielectric/semiconductor interface and the activation energy in the transistor channel. This work provides a one-step solution processing technique, which makes use of soluble ambipolar small molecules to form a thin-film semiconductor for application in high-performance OFETs.

  1. Evaluation of drug-polymer miscibility in amorphous solid dispersion systems.

    Science.gov (United States)

    Rumondor, Alfred C F; Ivanisevic, Igor; Bates, Simon; Alonzo, David E; Taylor, Lynne S

    2009-11-01

    To evaluate drug-polymer miscibility behavior in four different drug-polymer amorphous solid dispersion systems, namely felodipine-poly(vinyl pyrrolidone) (PVP), nifedipine-PVP, ketoconazole-PVP, and felodipine-poly(acrylic acid) (PAA). Amorphous solid dispersion samples were prepared at different drug-to-polymer ratios and analyzed using differential scanning calorimetry (DSC), mid-infrared (IR) spectroscopy, and powder X-ray diffractometry (PXRD). To help with interpretation of the IR spectra, principal components (PC) analysis was performed. Pair Distribution Functions (PDFs) of the components in the dispersion were determined from the PXRD data, and the pure curves of the components were also extracted from PXRD data using the Pure Curve Resolution Method (PCRM) and compared against experimentally obtained results. Molecular-level mixing over the complete range of concentration was verified for nifedipine-PVP and felodipine-PVP. For felodipine-PAA, drug-polymer immiscibility was verified for samples containing 30 to 70% polymer, while IR results suggest at least some level of mixing for samples containing 10 and 90% polymer. For ketoconazole-PVP system, partial miscibility is suspected, whereby the presence of one-phase amorphous solid dispersion system could only be unambiguously verified at higher concentrations of polymer. The three techniques mentioned complement each other in establishing drug-polymer miscibility in amorphous solid dispersion systems. In particular, IR spectroscopy and PXRD are sensitive to changes in local chemical environments and local structure, which makes them especially useful in elucidating the nature of miscibility in binary mixtures when DSC results are inconclusive or variable.

  2. Hot Melt Extrusion and Spray Drying of Co-amorphous Indomethacin-Arginine With Polymers.

    Science.gov (United States)

    Lenz, Elisabeth; Löbmann, Korbinian; Rades, Thomas; Knop, Klaus; Kleinebudde, Peter

    2017-01-01

    Co-amorphous drug-amino acid systems have gained growing interest as an alternative to common amorphous formulations which contain polymers as stabilizers. Several preparation methods have recently been investigated, including vibrational ball milling on a laboratory scale or spray drying in a larger scale. In this study, the feasibility of hot melt extrusion for continuous manufacturing of co-amorphous drug-amino acid formulations was examined, challenging the fact that amino acids melt with degradation at high temperatures. Furthermore, the need for an addition of a polymer in this process was evaluated. After a polymer screening via the solvent evaporation method, co-amorphous indomethacin-arginine was prepared by a melting-solvent extrusion process without and with copovidone. The obtained products were characterized with respect to their solid-state properties, non-sink dissolution behavior, and stability. Results were compared to those of spray-dried formulations with the same compositions and to spray-dried indomethacin-copovidone. Overall, stable co-amorphous systems could be prepared by extrusion without or with copovidone, which exhibited comparable molecular interaction properties to the respective spray-dried products, while phase separation was detected by differential scanning calorimetry in several cases. The formulations containing indomethacin in combination with arginine and copovidone showed enhanced dissolution behavior over the formulations with only copovidone or arginine. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

  3. Amorphous/crystal and polymer/filler interphases in biocomposites from poly(butylene succinate)

    Energy Technology Data Exchange (ETDEWEB)

    Signori, Francesca [Consiglio Nazionale delle Ricerche - Istituto per i Processi Chimico-Fisici (CNR-IPCF), Via G. Moruzzi 1, I-56124 Pisa (Italy); Pelagaggi, Martina [Universita di Pisa - Dipartimento di Chimica e Chimica Industriale, Via Risorgimento 35, I-56126 Pisa (Italy); Bronco, Simona [Consiglio Nazionale delle Ricerche - Istituto per i Processi Chimico-Fisici (CNR-IPCF), Via G. Moruzzi 1, I-56124 Pisa (Italy); Righetti, Maria Cristina, E-mail: righetti@ipcf.cnr.it [Consiglio Nazionale delle Ricerche - Istituto per i Processi Chimico-Fisici (CNR-IPCF), Via G. Moruzzi 1, I-56124 Pisa (Italy)

    2012-09-10

    Highlights: Black-Right-Pointing-Pointer The existence of intermolecular interactions between poly(butylene succinate) and hemp fibres was proved from specific heat capacities data. Black-Right-Pointing-Pointer Different degrees of mobility of the poly(butylene succinate) amorphous segments were evidenced at the amorphous/crystal interphase. Black-Right-Pointing-Pointer Devitrification of the rigid amorphous fraction in poly(butylene succinate) was found to occur before and simultaneously with the fusion. - Abstract: Poly(butylene succinate)-hemp composites (PBS-hemp), with hemp content in the range 0-40 wt.%, were prepared in the melt and characterized. This paper focuses on the detailed analysis of the thermal behaviour of the PBS-hemp composites, investigated by differential scanning calorimetry (DSC), to enlighten the polymer/fibre interphase features. The occurrence of specific intermolecular interactions between PBS and hemp was assessed from specific heat capacity data. Different degrees of mobility of the PBS amorphous segments were found at the amorphous/crystal interphases. A broadening of the bulk glass transition was observed, and attributed to the presence of polymer segments slightly constrained. Moreover, a rigid amorphous fraction that devitrifies at temperatures higher than the bulk glass transition, partly before the melting region and partly simultaneously with the fusion, was observed and quantified, and attributed to the presence of major constraints probably occurring in geometrically restricted areas.

  4. Preformulation studies and characterization of the physicochemical properties of amorphous polymers using artificial neural networks.

    Science.gov (United States)

    Ebube, N K; Owusu-Ababio, G; Adeyeye, C M

    2000-02-25

    The utility of artificial neural networks (ANNs) as a preformulation tool to determine the physicochemical properties of amorphous polymers such as the hydration characteristics, glass transition temperatures and rheological properties was investigated. The neural network simulator, CAD/Chem, based on the delta back-propagation paradigm was used for this study. The ANNs software was trained with sets of experimental data consisting of different polymer blends with known water-uptake profiles, glass transition temperatures and viscosity values. A set of similar data, not initially exposed to the ANNs was used to validate the ability of the ANNs to recognize patterns. The results of this investigation indicate that the ANNs accurately predicted the water-uptake, glass transition temperatures and viscosities of different amorphous polymers and their physical blends with a low % error (0-8%) of prediction. The ANNs also showed good correlation between the water-uptake and changes in the glass transition temperatures of the polymers. This study demonstrated the potential of the ANNs as a preformulation tool to evaluate the characteristics of amorphous polymers. This is particularly relevant when designing sustained release formulations that require the use of a fast hydrating polymer matrix.

  5. On cavitation, post-cavitation and yield in amorphous polymer-rubber blends

    NARCIS (Netherlands)

    Steenbrink, A.C.; Giessen, E. van der

    1999-01-01

    The deformation behaviour of amorphous polymer-rubber blends is investigated in terms of an axisymmetric unit cell model containing an initially spherical rubber particle. The behaviour of the rubber is described by an incompressible non-Gaussian network theory, while for the matrix we adopt a

  6. Hot Melt Extrusion and Spray Drying of Co-amorphous Indomethacin-Arginine With Polymers

    DEFF Research Database (Denmark)

    Lenz, Elisabeth; Löbmann, Korbinian; Rades, Thomas

    2017-01-01

    was evaluated. After a polymer screening via the solvent evaporation method, co-amorphous indomethacin-arginine was prepared by a melting-solvent extrusion process without and with copovidone. The obtained products were characterized with respect to their solid-state properties, non-sink dissolution behavior...

  7. Inhibition of surface crystallisation of amorphous indomethacin particles in physical drug-polymer mixtures

    DEFF Research Database (Denmark)

    Priemel, Petra A; Laitinen, Riikka; Barthold, Sarah

    2013-01-01

    or Soluplus(®) in 3:1, 1:1 and 1:3 (w/w) ratios were stored at 30°C and 23 or 42% RH. Samples were analysed during storage by X-ray powder diffraction, thermogravimetric analysis, differential scanning calorimetry, and scanning electron microscopy (SEM). IMC Eudragit(®) mixtures showed higher physical......Surface coverage may affect the crystallisation behaviour of amorphous materials. This study investigates crystallisation inhibition in powder mixtures of amorphous drug and pharmaceutical excipients. Pure amorphous indomethacin (IMC) powder and physical mixtures thereof with Eudragit(®) E...... through reduced IMC surface molecular mobility. Polymer particles may also mechanically hinder crystal growth outwards from the surface. This work highlights the importance of microparticulate surface coverage of amorphous drug particles on their stability....

  8. Influence of molecular weight on the short-channel effect in polymer-based field-effect transistors

    NARCIS (Netherlands)

    Tunc, Ali Veysel; Ecker, Bernhard; Dogruyol, Zekeriya; Juechter, Sabrina; Ugur, Ahmet Lutfi; Erdogmus, Ali; San, Sait Eren; Parisi, Juergen; von Hauff, Elizabeth

    2012-01-01

    In this study, we demonstrate how the intrinsic properties of a polymer can influence the electrical characteristics of organic field-effect transistors (OFETs). OFETs fabricated with three batches of poly[2-methoxy,5-(3′,7′-dimethyl-octyloxy)]-p-phenylene vinylene (MDMO-PPV) were investigated. The

  9. Controlling of the surface energy of the gate dielectric in organic field-effect transistors by polymer blend

    NARCIS (Netherlands)

    Gao, Jia; Asadi, Kamal; Xu, Jian Bin; An, Jin

    2009-01-01

    In this letter, we demonstrate that by blending insulating polymers, one can fabricate an insulating layer with controllable surface energy for organic field-effect transistors. As a model system, we used copper phthalocyanine evaporated on layers of polymethyl metacrylate blended with polystyrene

  10. Crosslinkable high k polymer dielectrics for low voltage organic field-effect transistor memories (Conference Presentation)

    Science.gov (United States)

    Wu, Hung-Chin; Hung, Chih-Chien; Chiu, Yu-Cheng; Tung, Shih-Huang; Chen, Wen-Chang

    2016-09-01

    High Performance organic field-effect transistor (OFET) memory devices were successfully prepared using new dielectric materials, poly(N-(hydroxymethyl)acrylamide-co-5 -(9-(5-(diethylamino)pentyl)-2-(4-vinylphenyl)-9H-fluorene (P(NMA-co-F6NSt)), which contained chemical cross-linkable segment (NMA) and hole trapping building block (F6NSt). The high k characteristics of P(NMA-co-F6NSt)) led to a low voltage operation, a small power consumption, and a good digital information storage capacity. Such P(NMA-co-F6NSt) dielectrics in OFET memories with variant NMA/F6NSt molar ratios (100/0 (P1), 95/5 (P2), 80/20 (P3), and 67/33 (P4)) showed excellent insulating properties and good charge storage performance under a low operating voltage below ±5V, due to the tightly network structures after crosslinking and well-dispersed trapping cites (i.e. fluorene moieties). P3-based memory device, in particular, exhibited largest memory window of 4.13 V among the studied polymers, and possessed stable data retention stability over 104 s with a high on/off current ratio (i.e. 104) and good endurance characteristics of more than 200 write-read-write-erase (WRER) cycles. The above results suggested that a high-performance OFET memory device could be facilely achieved using the novel synthesized high-k copolymers.

  11. Fabrication of an organic field effect transistor using nano imprinting of Ag inks and semiconducting polymers

    International Nuclear Information System (INIS)

    Hu, PingAn; Li, Kun; O'Neill, William; Chen, Weilin; Peng, Li; Chu, Daping

    2010-01-01

    A simple and cheap procedure for flexible electronics fabrication was demonstrated by imprinting metallic nanoparticles (NPs) on flexible substrates. Silver NPs with an average diameter of 10 nm were prepared via an improved chemical approach and Ag Np ink was produced in α-terpineol with a concentration up to 15%. Silver micro/nanostructures with a dimension varying from nanometres to microns were produced on a flexible substrate (polyimide) by imprinting the as-prepared silver ink. The fine fluidic properties of an Ag NP/α-terpineol solution and low melting temperatures of silver nanoparticles render a low pressure and low temperature procedure, which is well suited for flexible electronics fabrication. The effects of sintering and mechanical bending on the conductivity of imprinted silver contacts were also investigated. Large area organic field effect transistors (OFET) on flexible substrates were fabricated using an imprinted silver electrode and semiconducting polymer. The OFET with silver electrodes imprinted from our prepared oleic acid stabilized Ag nanoparticle ink show an ideal ohmic contact; therefore, the OFET exhibit high performance (I on /I off ratio: 1 × 10 3 ; mobility: 0.071 cm 2 V −1 s −1 ).

  12. On electronic structure of polymer-derived amorphous silicon carbide ceramics

    Science.gov (United States)

    Wang, Kewei; Li, Xuqin; Ma, Baisheng; Wang, Yiguang; Zhang, Ligong; An, Linan

    2014-06-01

    The electronic structure of polymer-derived amorphous silicon carbide ceramics was studied by combining measurements of temperature-dependent conductivity and optical absorption. By comparing the experimental results to theoretical models, electronic structure was constructed for a carbon-rich amorphous silicon carbide, which revealed several unique features, such as deep defect energy level, wide band-tail band, and overlap between the band-tail band and defect level. These unique features were discussed in terms of the microstructure of the material and used to explain the electric behavior.

  13. Microstructure of an immiscible polymer blend and its stabilization effect on amorphous solid dispersions.

    Science.gov (United States)

    Yang, Ziyi; Nollenberger, Kathrin; Albers, Jessica; Craig, Duncan; Qi, Sheng

    2013-07-01

    This study proposes use of the phase separation of immiscible polymer blends as a formulation approach to improve the stabilization and solubilization of amorphous molecular dispersions of poorly soluble drugs. This approach uses the phase separation and different drug solubilization properties of the two immiscible polymers in the blend to optimize drug loading and stabilization. The model system tested in this study is a EUDRAGIT E PO-PVP-VA 50/50 (w/w) blend loaded with felodipine via hot melt extrusion. The phase separation behavior of the polymer blend and drug loaded polymer blend formulations were characterized using a range of thermal (MTDSC), spectroscopic (ATR-FTIR), and imaging (AFM and thermal transition mapping) techniques. The polymer blend formulations demonstrated superior performance in drug release as well as stabilization against stressed temperature, stressed humidity, and mechanical milling in comparison to the drug-polymer binary systems. This is attributed to the configuration of the phase separated microstructure of the polymer blend formulations where the hydrophilic polymer domains host high concentrations of molecularly dispersed drug which are protected from moisture induced recrystallization on aging by the hydrophobic polymer domains. Additionally drug incorporation as a molecular dispersion in different polymer phases reduces the drug recrystallization tendency on aging under high temperatures and during milling.

  14. Polymer ferroelectric field-effect memory device with SnO channel layer exhibits record hole mobility

    KAUST Repository

    Caraveo-Frescas, Jesus Alfonso

    2014-06-10

    Here we report for the first time a hybrid p-channel polymer ferroelectric field-effect transistor memory device with record mobility. The memory device, fabricated at 200C on both plastic polyimide and glass substrates, uses ferroelectric polymer P(VDF-TrFE) as the gate dielectric and transparent p-type oxide (SnO) as the active channel layer. A record mobility of 3.3 cm 2V-1s-1, large memory window (~16 V), low read voltages (~-1 V), and excellent retention characteristics up to 5000 sec have been achieved. The mobility achieved in our devices is over 10 times higher than previously reported polymer ferroelectric field-effect transistor memory with p-type channel. This demonstration opens the door for the development of non-volatile memory devices based on dual channel for emerging transparent and flexible electronic devices.

  15. Miniaturized screening of polymers for amorphous drug stabilization (SPADS): rapid assessment of solid dispersion systems.

    Science.gov (United States)

    Wyttenbach, Nicole; Janas, Christine; Siam, Monira; Lauer, Matthias Eckhard; Jacob, Laurence; Scheubel, Emmanuel; Page, Susanne

    2013-08-01

    Development of a novel, rapid, miniaturized approach to identify amorphous solid dispersions with maximum supersaturation and solid state stability. Three different miniaturized assays are combined in a 2-step decision process to assess the supersaturation potential and drug-polymer miscibility and stability of amorphous compositions. Step 1: SPADS dissolution assay. Drug dissolution is determined in 96-well plates to detect systems that generate and maintain supersaturation. Promising combinations graduate to step 2. Step 2: SPADS interaction and SPADS imaging assays. FTIR microspectroscopy is used to study intermolecular interactions. Atomic force microscopy is applied to analyze molecular homogeneity and stability. Based on the screening results, selected drug-polymer combinations were also prepared by spray-drying and characterized by classical dissolution tests and a 6-month physical stability study. From the 7 different polymers and 4 drug loads tested, EUDRAGIT E PO at a drug load of 20% performed best for the model drug CETP(2). The classical dissolution and stability tests confirmed the results from the miniaturized assays. The results demonstrate that the SPADS approach is a useful de-risking tool allowing the rapid, rational, time- and cost-effective identification of polymers and drug loads with appropriate dual function in supersaturation performance and amorphous drug stabilization. Copyright © 2013 Elsevier B.V. All rights reserved.

  16. Gas Adsorption Characterization of Rigid and Amorphous Polymers

    Science.gov (United States)

    Larsen, Gregory; Siperstein, Flor; Budd, Peter; Colina, Coray

    2008-03-01

    Nanostructured materials have unusual mechanical, electrical and optical properties and are becoming increasingly important for energy storage. A variety of materials, such as zeolites, metal organic frameworks, covalent organic frameworks, activated carbons, and hypercrosslinked polymers, have recently been explored for energy storage. Polymers of Intrisic Microporosisity (PIMs) are macromolecules that form nanoporous materials (effective pore size structure of the selected monomers, but can be flexible at a macroscopic scale and show swelling properties due to their polymeric nature. PIMs offer an interesting alternative to the materials mentioned above, as the functionality can be directly embedded in the material framework, allowing for intrinsic control in adsorptive properties by the PIM and flexibility in alternate adsorption applications such as CO2 sequestration. In this work, we present our recent efforts to study PIMs by MC simulations, and demonstrate the effects of box size and chain length on simulated measurements including pore size distribution and surface area.

  17. Effect of polymer type and drug dose on the in vitro and in vivo behavior of amorphous solid dispersions

    DEFF Research Database (Denmark)

    Knopp, Matthias Manne; Chourak, Nabil; Khan, Fauzan

    2016-01-01

    This study investigated the non-sink in vitro dissolution behavior and in vivo performance in rats of celecoxib (CCX) amorphous solid dispersions with polyvinyl acetate (PVA), polyvinylpyrrolidone (PVP) and hydroxypropyl methylcellulose (HPMC) at different drug doses. Both in vitro and in vivo......, the amorphous solid dispersions with the hydrophilic polymers PVP and HPMC led to higher areas under both, the in vitro dissolution and the plasma concentration-time curves (AUC) compared to crystalline and amorphous CCX for all doses. In contrast, the amorphous solid dispersion with the hydrophobic polymer PVA...... showed a lower AUC both in vitro and in vivo than crystalline CCX. For crystalline CCX and CCX:PVA, the in vitro AUC was limited by the low solubility of the drug and the slow release of the drug from the hydrophobic polymer, respectively. For the supersaturating formulations, amorphous CCX, CCX...

  18. Thiophene-Thiazole-Based Semiconducting Copolymers for High-Performance Polymer Field-Effect Transistors.

    Science.gov (United States)

    Chung, Jong Won; Park, Won-Tae; Park, Jeong-Il; Yun, Youngjun; Gu, Xiaodan; Lee, Jiyoul; Noh, Yong-Young

    2017-11-08

    We report a newly synthesized donor (D)-acceptor (A)type semiconducting copolymer, consisting of thiophene as an electron-donating unit and thiazole as an electron-accepting unit (PQTBTz-TT-C8) for the active layer of the organic field-effect transistors (OFETs). Specifically, this study investigates the structure and electrical property relationships of PQTBTz-TT-C8 with comprehensive analyses on the charge-transporting properties corresponding to the spin rate of the spin coater during the formation of the PQTBTz-TT-C8 film. The crystallinity of PQTBTz-TT-C8 films is examined with grazing incidence X-ray diffraction. Temperature-dependent transfer measurements of the OFETs are conducted to extract the density of states (DOS) and characterize the charge-transport properties. Comparative analyses on charge transports within the framework of the physical model, based on polaron hopping and Gaussian DOS, reveal that the prefactors of both physical charge-transport models are independent of the spin-coating condition for the films. For staggered structural transistors, however, the thickness of the PQTBTz-TT-C8 films, which strongly affect the series resistance along the charge-transfer path in a vertical direction, is changed in accordance with the spin-coating rate. In other words, the spin-coating rate of the PQTBTz-TT-C8 films influences the thickness of the polymer films, yet any significant changes in the crystallinity of the film or electronic coupling between the neighboring molecules upon the spin-coating condition were barely noticeable. Because the PQTBTz-TT-C8 backbone chains inside the thin film are stacked up with the edge-on, the series resistances are changed according to the thickness of the film and thus the performance of the device varies depending on the thickness.

  19. Fabrication and independent control of patterned polymer gate for a few-layer WSe2 field-effect transistor

    Directory of Open Access Journals (Sweden)

    Sung Ju Hong

    2016-08-01

    Full Text Available We report the fabrication of a patterned polymer electrolyte for a two-dimensional (2D semiconductor, few-layer tungsten diselenide (WSe2 field-effect transistor (FET. We expose an electron-beam in a desirable region to form the patterned structure. The WSe2 FET acts as a p-type semiconductor in both bare and polymer-covered devices. We observe a highly efficient gating effect in the polymer-patterned device with independent gate control. The patterned polymer gate operates successfully in a molybdenum disulfide (MoS2 FET, indicating the potential for general applications to 2D semiconductors. The results of this study can contribute to large-scale integration and better flexibility in transition metal dichalcogenide (TMD-based electronics.

  20. Reduced Crystallization Temperature Methodology for Polymer Selection in Amorphous Solid Dispersions: Stability Perspective.

    Science.gov (United States)

    Bhugra, Chandan; Telang, Chitra; Schwabe, Robert; Zhong, Li

    2016-09-06

    API-polymer interactions, used to select the right polymeric matrix with an aim to stabilize an amorphous dispersion, are routinely studied using spectroscopic and/or calorimetric techniques (i.e., melting point depression). An alternate selection tool has been explored to rank order polymers for formation of stable amorphous dispersions as a pragmatic method for polymer selection. Reduced crystallization temperature of API, a parameter introduced by Zhou et al.,1 was utilized in this study for rank ordering interactions in API-polymeric systems. The trends in reduced crystallization temperature monitored over polymer concentration range of up to 20% polymer loading were utilized to calculate "crystallization parameter" or CP for two model systems (nifedipine and BI ABC). The rank order of CP, i.e., a measure of API-polymer interaction, for nifedipine followed the order PVP > PVP-VA > Soluplus > HPMCAS > PV Ac > PAA. This rank ordering was correlated to published results of molecular interactions and physical stability for nifedipine. A different rank ordering was observed for BI ABC: PAA > PVP > HPMCAS > Soluplus > PVPV-VA > PVAc. Interactions for BI ABC were not as differentiated when compared to nifedipine based on CP trends. BI ABC dispersions at drug loadings between 40 and 60% were physically stable for prolonged periods under ICH conditions as well as accelerated stress. We propose that large CP differences among polymers could be predictive of stability outcomes. Acceptable stability at pharmaceutically relevant drug loadings would suggest that the relative influence of downstream processes, such as polymer solubility in various solvents, process suitability and selection, and more importantly supersaturation potential, should be higher compared to stability considerations while developing compounds like BI ABC.

  1. Mid-infrared spectroscopy as a polymer selection tool for formulating amorphous solid dispersions.

    Science.gov (United States)

    Wegiel, Lindsay A; Mauer, Lisa J; Edgar, Kevin J; Taylor, Lynne S

    2014-02-01

    The development of amorphous solid dispersions is of increasing interest in the delivery of bioactive compounds; however, there is a need for a methodology that enables the rational selection of polymers for solid dispersion formulations with optimal stability to crystallization. The objective of this study was to evaluate the use of mid-infrared (IR) spectroscopy for this purpose. Polymers evaluated included poly(vinylpyrrolidone) (PVP), Eudragit E100 (E100), carboxymethylcellulose acetate butyrate (CMCAB), hydroxypropylmethylcellulose (HPMC), HPMC acetate succinate (HPMCAS) and poly(acrylic acid) (PAA). Model crystalline bioactive polyphenols included quercetin and naringenin. Amorphous solid dispersions were prepared by dissolving both polyphenol and polymer in a common solvent followed by solvent evaporation. Mid-IR spectroscopy was used to determine and quantify the extent of polyphenol-polymer interactions, and powder X-ray diffraction was used to monitor physical stability following storage at different environmental conditions. The mid-IR analysis suggested the following rank order for the crystallization-inhibiting performance of the different polymers: E100 > PVP > HPMCAS > HPMC ≥ CMCAB > PAA. The initial performance of the different polymers was evaluated using the highest concentration of polyphenol for which x-ray amorphous solid dispersions could be prepared via rotary evaporation. The observed stability followed that predicted from the mid-infrared spectroscopy evaluation of intermolecular interactions. The dispersions with better polyphenol-polymer interactions were stable against crystallization when exposed to high relative humidity and high temperatures; on the other hand, systems that had weak interactions were not stable to crystallization when stored at moderate environmental conditions. Based on the observed ability of mid-IR analysis to enable the characterization of intermolecular polyphenol-polymer interactions and

  2. Cyclopentadithiophene–naphthalenediimide polymers; synthesis, characterisation, and n-type semiconducting properties in field-effect transistors and photovoltaic devices

    Energy Technology Data Exchange (ETDEWEB)

    Li, Chun-Han [Department of Chemical Engineering, Frontier Research Center on Fundamental and Applied Sciences of Matters, National Tsing-Hua University, 101, Sec. 2, Kuang-Fu Road, Hsin-Chu 30013, Taiwan (China); Kettle, Jeff [School of Electronics, Bangor University, Dean st., Bangor, Gwynedd, LL57 1UT Wales (United Kingdom); Horie, Masaki, E-mail: mhorie@mx.nthu.edu.tw [Department of Chemical Engineering, Frontier Research Center on Fundamental and Applied Sciences of Matters, National Tsing-Hua University, 101, Sec. 2, Kuang-Fu Road, Hsin-Chu 30013, Taiwan (China)

    2014-04-01

    The synthesis, characterisation, and device performance of a series of cyclopentadithiophene (CPDT)-naphthalenediimide (NDI) donor-acceptor-donor (D-A-D) polymers is reported. The monomers with various alkyl chains are synthesised via direct arylation using palladium complex catalyst. The monomers are then polymerised by oxidative polymerisation using FeCl{sub 3} to provide high molecular weight polymers (M{sub n} = 21,800–76,000). The polymer films show deep-red absorption including near-infrared region up to 1100 nm to give optical bandgap of approximately 1.16 eV. The polymers exhibit only n-type semiconducting properties giving the highest electron mobility of 9 × 10{sup -3} cm{sup 2} V{sup −1} s{sup −1} in organic field-effect transistors (OFETs). Organic photovoltaic (OPV) devices are fabricated from solutions of the polymers as acceptors and poly(3-hexylthiophene) (P3HT) as a donor. - Highlights: • Cyclopentadithiophene–naphthalenediimide oligomers were prepared by direct arylation. • The oligomers were polymerised by oxidative reaction using iron(III)chloride. • The polymer films show deep-red absorption up to 1100 nm with a bandgap of 1.1 eV. • The polymers exhibit only n-type semiconducting properties in OFETs and OPVs.

  3. Impact of Drug-Polymer Miscibility on Enthalpy Relaxation of Irbesartan Amorphous Solid Dispersions.

    Science.gov (United States)

    Dalsania, Sonu; Sharma, Jagadish; Munjal, Bhushan; Bansal, Arvind K

    2018-01-09

    Drug-polymer miscibility has been proposed to play a critical role in physical stability of amorphous solid dispersions (ASDs). The purpose of the current work was to investigate the role of drug-polymer miscibility on molecular mobility, measured as enthalpy relaxation (ER) of amorphous irbesartan (IBS) in ASDs. Two polymers, i.e. polyvinylpyrrolidone K30 (PVP K30) and hydroxypropyl methylcellulose acetate succinate (HPMCAS), were used to generate ASDs with 10% w/w of the polymer. Drug-polymer miscibility was determined using melting point depression (MPD) method. Molecular mobility was assessed from ER studies at a common degree of undercooling (DOU) (T g  - 13.0°C ± 0.5°C). IBS exhibited higher miscibility in PVP K30 as compared to HPMCAS at temperature > 140°C. However, extrapolation of miscibility data to storage temperature (62°C) using Flory-Huggins (F-H) theory revealed a reversal of the trend. Miscibility of IBS was found to be higher in HPMCAS (2.6%) than PVP K30 (1.3%) at 62°C. Stretched relaxation time (τ β ) of 17.4365 h and 7.0886 h was obtained for IBS-HPMCAS and IBS-PVP K30 ASDs, respectively. Miscibility of drug-polymer at storage temperature explained the behavior of the molecular mobility, while miscibility near the melting point provided a reverse trend. Results suggest that drug-polymer miscibility determined at temperatures higher than the storage temperature should be viewed cautiously.

  4. Role of Chain Morphology and Stiffness in Thermal Conductivity of Amorphous Polymers.

    Science.gov (United States)

    Zhang, Teng; Luo, Tengfei

    2016-02-04

    Designing thermally conductive polymer is of scientific interest and practical importance for applications like thermal interface materials, electronics packing, and plastic heat exchangers. In this work, we study the fundamental relationship between the molecular morphology and thermal conductivity in bulk amorphous polymers. We use polyethylene as a model system and performed systematic parametric study in molecular dynamics simulations. We find that the thermal conductivity is a strong function of the radius of gyration of the molecular chains, which is further correlated to persistence length, an intrinsic property of the molecule that characterizes molecular stiffness. Larger persistence length can lead to more extended chain morphology and thus higher thermal conductivity. Further thermal conductivity decomposition analysis shows that thermal transport through covalent bonds dominates the effective thermal conductivity over other contributions from nonbonded interactions (van der Waals) and translation of molecules disregarding the morphology. As a result, the more extended chains due to larger persistence length provide longer spatial paths for heat to transfer efficiently and thus lead to higher thermal conductivity. In addition, rigid rod-like polymers with very large persistence length tend to spontaneously crystallize and form orientated chains, leading to a thermal conductivity increase by more than 1 order of magnitude. Our results will provide important insights into the design of thermally conductive amorphous polymers.

  5. Formation, Structure and Properties of Amorphous Carbon Char from Polymer Materials in Extreme Atmospheric Reentry Environments

    Science.gov (United States)

    Lawson, John W.

    2010-01-01

    Amorphous carbonaceous char produced from the pyrolysis of polymer solids has many desirable properties for ablative heat shields for space vehicles. Molecular dynamics simulations are presented to study the transformation of the local atomic structure from virgin polymer to a dense, disordered char [1]. Release of polymer hydrogen is found to be critical to allow the system to collapse into a highly coordinated char structure. Mechanisms of the char formation process and the morphology of the resulting structures are elucidated. Thermal conductivity and mechanical response of the resulting char are evaluated [2]. During reenty, the optical response and oxidative reactivity of char are also important properties. Results of ab initio computations of char optical functions [3] and char reactivity [4] are also presented.

  6. The Soft-Confined Method for Creating Molecular Models of Amorphous Polymer Surfaces

    KAUST Repository

    Liu, Hongyi

    2012-02-09

    The goal of this work was to use molecular dynamics (MD) simulations to build amorphous surface layers of polypropylene (PP) and cellulose and to inspect their physical and interfacial properties. A new method to produce molecular models for these surfaces was developed, which involved the use of a "soft" confining layer comprised of a xenon crystal. This method compacts the polymers into a density distribution and a degree of molecular surface roughness that corresponds well to experimental values. In addition, calculated properties such as density, cohesive energy density, coefficient of thermal expansion, and the surface energy agree with experimental values and thus validate the use of soft confining layers. The method can be applied to polymers with a linear backbone such as PP as well as those whose backbones contain rings, such as cellulose. The developed PP and cellulose surfaces were characterized by their interactions with water. It was found that a water nanodroplet spreads on the amorphous cellulose surfaces, but there was no significant change in the dimension of the droplet on the PP surface; the resulting MD water contact angles on PP and amorphous cellulose surfaces were determined to be 106 and 33°, respectively. © 2012 American Chemical Society.

  7. Synthesis and characterization of amorphous poly(ethylene oxide)/poly(trimethylene carbonate) polymer blend electrolytes

    International Nuclear Information System (INIS)

    Rodrigues, L.C.; Silva, M.M.; Smith, M.J.

    2012-01-01

    Solid polymer electrolytes (SPEs) have been proposed as substitutes for conventional non-aqueous electrolytes in various electrochemical devices. These promising materials may be of interest in various practical devices including batteries, sensors and electrochromic displays as they can offer high performance in terms of specific energy and specific power (batteries), safe operation, form flexibility in device arquitecture and low manufacturing costs. Many different host polymers have been characterized over the last 30 years, however a relatively un-explored strategy involves the use of interpenetrating blends incorporating two or more polymers. Electrolyte systems based on interpenetrating blends of known host polymers, poly(ethylene oxide) and poly(trimethylene carbonate), doped with lithium perchlorate, were prepared by co-dissolution in acetonitrile. This combination of polymer components results in the formation of a material that may be applicable in batteries and electrochromic devices. The results of characterization of polymer electrolyte systems based on interpenetrating blends of amorphous poly(ethylene oxide) and poly(trimethylene carbonate) host matrices, with lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) as guest salt, are described in this study. Electrolytes with compositions of n between 5 and 15 (where n represents the total number of cation-coordinating units per lithium ion) were obtained as flexible, transparent and free-standing films that were characterized by measurements of conductivity, cyclic voltammetry, differential scanning calorimetry and thermogravimetry.

  8. Structure-Property Relationships in Polymer Derived Amorphous/Nano-Crystalline Silicon Carbide for Nuclear Applications

    International Nuclear Information System (INIS)

    Zunjarrao, Suraj C.; Singh, Abhishek K.; Singh, Raman P.

    2006-01-01

    Silicon carbide (SiC) is a promising candidate for several applications in nuclear reactors owing to its high thermal conductivity, high melting temperature, good chemical stability, and resistance to swelling under heavy ion bombardment. However, fabricating SiC by traditional powder processing route generally requires very high temperatures for pressureless sintering. Polymer derived ceramic materials offer unique advantages such as ability to fabricate net shaped components, incorporate reinforcements and relatively low processing temperatures. Furthermore, for SiC based ceramics fabricated using polymer infiltration process (PIP), the microstructure can be tailored by controlling the processing parameters, to get an amorphous, nanocrystalline or crystalline SiC. In this work, fabrication of polymer derived amorphous and nano-grained SiC is presented and its application as an in-core material is explored. Monolithic SiC samples are fabricated by controlled pyrolysis of allyl-hydrido-poly-carbo-silane (AHPCS) under inert atmosphere. Chemical changes, phase transformations and microstructural changes occurring during the pyrolysis process are studied as a function of the processing temperature. Polymer cross-linking and polymer to ceramic conversion is studied using infrared spectroscopy (FTIR). Thermogravimetric analysis (TGA) and differential thermal analysis (DTA) are performed to monitor the mass loss and phase change as a function of temperature. X-ray diffraction studies are done to study the intermediate phases and microstructural changes. Variation in density is carefully monitored as a function of processing temperature. Owing to shrinkage and gas evolution during pyrolysis, precursor derived ceramics are inherently porous and composite fabrication typically involves repeated cycles of polymer re-infiltration and pyrolysis. However, there is a limit to the densification that can be achieved by this method and porosity in the final materials presents

  9. Experimental and modelling studies of the shape memory properties of amorphous polymer network composites

    International Nuclear Information System (INIS)

    Arrieta, J S; Diani, J; Gilormini, P

    2014-01-01

    Shape memory polymer composites (SMPCs) have become an important way to leverage improvements in the development of applications featuring shape memory polymers (SMPs). In this study, an amorphous SMP matrix has been filled with different types of reinforcements. An experimental set of results is presented and then compared to three-dimensional (3D) finite-element simulations. Thermomechanical shape memory cycles were performed in uniaxial tension. The fillers effect was studied in stress-free and constrained-strain recoveries. Experimental observations indicate complete shape recovery and put in evidence the increased sensitivity of constrained length stress recoveries to the heating ramp on the tested composites. The simulations reproduced a simplified periodic reinforced composite and used a model for the matrix material that has been previously tested on regular SMPs. The latter combines viscoelasticity at finite strain and time-temperature superposition. The simulations easily allow representation of the recovery properties of a reinforced SMP. (paper)

  10. On the Mass Fractal Character of Si-Based Structural Networks in Amorphous Polymer Derived Ceramics

    Directory of Open Access Journals (Sweden)

    Sabyasachi Sen

    2015-03-01

    Full Text Available The intermediate-range packing of SiNxC4−x (0 ≤ x ≤ 4 tetrahedra in polysilycarbodiimide and polysilazane-derived amorphous SiCN ceramics is investigated using 29Si spin-lattice relaxation nuclear magnetic resonance (SLR NMR spectroscopy. The SiCN network in the polysilylcarbodiimide-derived ceramic consists predominantly of SiN4 tetrahedra that are characterized by a 3-dimensional spatial distribution signifying compact packing of such units to form amorphous Si3N4 clusters. On the other hand, the SiCN network of the polysilazane-derived ceramic is characterized by mixed bonded SiNxC4−x tetrahedra that are inefficiently packed with a mass fractal dimension of Df ~2.5 that is significantly lower than the embedding Euclidean dimension (D = 3. This result unequivocally confirms the hypothesis that the presence of dissimilar atoms, namely, 4-coordinated C and 3-coordinated N, in the nearest neighbor environment of Si along with some exclusion in connectivity between SiCxN4−x tetrahedra with widely different N:C ratios and the absence of bonding between C and N result in steric hindrance to an efficient packing of these structural units. It is noted that similar inefficiencies in packing are observed in polymer-derived amorphous SiOC ceramics as well as in proteins and binary hard sphere systems.

  11. On the Mass Fractal Character of Si-Based Structural Networks in Amorphous Polymer Derived Ceramics.

    Science.gov (United States)

    Sen, Sabyasachi; Widgeon, Scarlett

    2015-03-17

    The intermediate-range packing of SiN x C 4- x (0 ≤ x ≤ 4) tetrahedra in polysilycarbodiimide and polysilazane-derived amorphous SiCN ceramics is investigated using 29 Si spin-lattice relaxation nuclear magnetic resonance (SLR NMR) spectroscopy. The SiCN network in the polysilylcarbodiimide-derived ceramic consists predominantly of SiN₄ tetrahedra that are characterized by a 3-dimensional spatial distribution signifying compact packing of such units to form amorphous Si₃N₄ clusters. On the other hand, the SiCN network of the polysilazane-derived ceramic is characterized by mixed bonded SiN x C 4- x tetrahedra that are inefficiently packed with a mass fractal dimension of D f ~2.5 that is significantly lower than the embedding Euclidean dimension ( D = 3). This result unequivocally confirms the hypothesis that the presence of dissimilar atoms, namely, 4-coordinated C and 3-coordinated N, in the nearest neighbor environment of Si along with some exclusion in connectivity between SiC x N 4- x tetrahedra with widely different N:C ratios and the absence of bonding between C and N result in steric hindrance to an efficient packing of these structural units. It is noted that similar inefficiencies in packing are observed in polymer-derived amorphous SiOC ceramics as well as in proteins and binary hard sphere systems.

  12. Effects of alkyl chain positioning on conjugated polymer microstructure and field-effect mobilities

    KAUST Repository

    Schroeder, Bob C.

    2015-07-02

    Solubilizing alkyl chains play a crucial role in the design of semiconducting polymers because they define the materials solubility and processability as well as both the crystallinity and solid-state microstructure. In this paper, we present a scarcely explored design approach by attaching the alkyl side chains on one side (cis-) or on both sides (trans-) of the conjugated backbone. We further investigate the effects of this structural modification on the solid-state properties of the polymers and on the charge-carrier mobilities in organic thin-film transistors. Copyright © Materials Research Society 2015

  13. Organic Field Effect Transistors with Dipole-Polarized Polymer Gate Dielectrics for Control of Threshold Voltage

    OpenAIRE

    Sakai, Heisuke; Takahashi, Yoshikazu; Murata, Hideyuki

    2007-01-01

    The authors demonstrate organic field effect transistors (OFETs) with a dipole-polarized polyurea for the gate dielectrics. In the dielectrics, the internal electric field induces the mobile charge carrier in the semiconductor layer to the semiconductor-dielectric interface. OFETs with dipole-polarized gate dielectrics exhibit lower threshold voltage. With nonpolarized gate dielectrics, the threshold voltage was -11.4 V, whereas that decreased to -5.3 V with polarized gate dielectrics. In a...

  14. Biotin-Functionalized Semiconducting Polymer in an Organic Field Effect Transistor and Application as a Biosensor

    Directory of Open Access Journals (Sweden)

    Yong Suk Yang

    2012-08-01

    Full Text Available This report presents biotin-functionalized semiconducting polymers that are based on fluorene and bithiophene co-polymers (F8T2. Also presented is the application of these polymers to an organic thin film transistor used as a biosensor. The side chains of fluorene were partially biotinylated after the esterification of the biotin with corresponding alcohol-groups at the side chain in F8T2. Their properties as an organic semiconductor were tested using an organic thin film transistor (OTFT and were found to show typical p-type semiconductor curves. The functionality of this biosensor in the sensing of biologically active molecules such as avidin in comparison with bovine serum albumin (BSA was established through a selective decrease in the conductivity of the transistor, as measured with a device that was developed by the authors. Changes to the optical properties of this polymer were also measured through the change in the color of the UV-fluorescence before and after a reaction with avidin or BSA.

  15. Dihedral angle control to improve the charge transport properties of conjugated polymers in organic field effect transistors

    Science.gov (United States)

    Dharmapurikar, Satej S.; Chithiravel, Sundaresan; Mane, Manoj V.; Deshmukh, Gunvant; Krishnamoorthy, Kothandam

    2018-03-01

    Diketopyrrolopyrrole (DPP) and i-Indigo (i-Ind) are two monomers that are widely explored as active materials in organic field effect transistor and solar cells. These two molecules showed impressive charge carrier mobility due to better packing that are facilitated by quadrupoles. We hypothesized that the copolymers of these monomers would also exhibit high charge carrier mobility. However, we envisioned that the dihedral angle at the connecting point between the monomers will play a crucial role in packing as well as charge transport. To understand the impact of dihedral angle on charge transport, we synthesized three copolymers, wherein the DPP was sandwiched between benzenes, thiophenes and furans. The copolymer of i-Indigo and furan comprising DPP showed a band gap of 1.4 eV with a very high dihedral angle of 179°. The polymer was found to pack better and the coherence length was found to be 112 Å. The hole carrier mobility of these polymer was found to be highest among the synthesized polymer i.e. 0.01 cm2/vs. The copolymer comprising benzene did not transport hole and electrons. The dihedral angle at the connecting point between i and Indigo and benzene DPP was 143 Å, which the packing and consequently charge transport properties.

  16. Drug-polymer-water interaction and its implication for the dissolution performance of amorphous solid dispersions.

    Science.gov (United States)

    Chen, Yuejie; Liu, Chengyu; Chen, Zhen; Su, Ching; Hageman, Michael; Hussain, Munir; Haskell, Roy; Stefanski, Kevin; Qian, Feng

    2015-02-02

    The in vitro dissolution mechanism of an amorphous solid dispersion (ASD) remains elusive and highly individualized, yet rational design of ASDs with optimal performance and prediction of their in vitro/in vivo performance are very much desirable in the pharmaceutical industry. To this end, we carried out comprehensive investigation of various ASD systems of griseofulvin, felodipine, and ketoconazole, in PVP-VA or HPMC-AS at different drug loading. Physiochemical properties and processes related to drug-polymer-water interaction, including the drug crystallization tendency in aqueous medium, drug-polymer interaction before and after moisture exposure, supersaturation of drug in the presence of polymer, polymer dissolution kinetics, etc., were characterized and correlated with the dissolution performance of ASDs at different dose and different drug/polymer ratio. It was observed that ketoconazole/HPMC-AS ASD outperformed all other ASDs in various dissolution conditions, which was attributed to the drug's low crystallization tendency, the strong ketoconazole/HPMC-AS interaction and the robustness of this interaction against water disruption, the dissolution rate and the availability of HPMC-AS in solution, and the ability of HPMC-AS in maintaining ketoconazole supersaturation. It was demonstrated that all these properties have implications for the dissolution performance of various ASD systems, and further quantification of them could be used as potential predictors for in vitro dissolution of ASDs. For all ASDs investigated, HPMC-AS systems performed better than, or at least comparably with, their PVP-VA counterparts, regardless of the drug loading or dose. This observation cannot be solely attributed to the ability of HPMC-AS in maintaining drug supersaturation. We also conclude that, for fast crystallizers without strong drug-polymer interaction, the only feasible option to improve dissolution might be to lower the dose and the drug loading in the ASD. In this

  17. Photo-Curable Polymer Blend Dielectrics for Advancing Organic Field-Effect Transistor Applications

    Energy Technology Data Exchange (ETDEWEB)

    S Kim; K Hong; M Jang; J Jang; J Anthony; H Yang; C Park

    2011-12-31

    A solution method of photo-curable and -patternable polymer gate dielectrics was introduced by using blend solutions of poly(4-dimethylsilyl styrene) (PDMSS) and poly(melamine-co-formaldehyde) acrylate (PMFA). The fabrication was optimized to produce a smooth hydrophobic gate dielectric with good insulating and solvent-resistant properties. On the optimized PDMSS/PMFA blend gate dielectric, pentacene could grow into highly ordered structure, showing high electric performances for the resulting OFETs, as well as PTCDI-C13 and TES-ADT.

  18. Development of fully amorphous dispersions of a low T(g) drug via co-spray drying with hydrophilic polymers.

    Science.gov (United States)

    Zhao, Min; Barker, Susan A; Belton, Peter S; McGregor, Caroline; Craig, Duncan Q M

    2012-11-01

    The aim of the study was to prepare molecular dispersions of a physically highly unstable amorphous drug, paracetamol (acetaminophen with a T(g) of ca. 25°C) via co-spray drying with a variety of polymers. Solid dispersions at a range of drug loadings (10-90%w/w) using hydroxypropyl methylcellulose/acetate succinate (HPMC/HPMC AS), polyvinylpyrrolidone (PVP) and copovidone were produced and characterised by modulated temperature differential scanning calorimetry (MTDSC), thermogravimetric analysis (TGA), X-ray powder diffraction (XRPD), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). PVP-based polymers showed a greater tendency than the HPMC-based group to generate temperature-stable dispersions. In particular, copovidone (Plasdone® S-630) was found to be the most effective of the polymers studied and could formulate molecular dispersions at drug loadings up to and including 40%w/w. However, no evidence for direct drug-polymer interactions was found for such systems as a possible stabilising mechanism. The expected relationship of a higher T(g) of the polymer leading to greater stabilisation was not observed, while there was an inverse relationship between viscosity grade and amorphous phase generation. The study has therefore shown that temperature-stable amorphous dispersions of a low T(g) drug may be prepared by co-spray drying, particularly using PVP-based polymers. Copyright © 2012 Elsevier B.V. All rights reserved.

  19. Effect of polymer type and drug dose on the in vitro and in vivo behavior of amorphous solid dispersions.

    Science.gov (United States)

    Knopp, Matthias Manne; Chourak, Nabil; Khan, Fauzan; Wendelboe, Johan; Langguth, Peter; Rades, Thomas; Holm, René

    2016-08-01

    This study investigated the non-sink in vitro dissolution behavior and in vivo performance in rats of celecoxib (CCX) amorphous solid dispersions with polyvinyl acetate (PVA), polyvinylpyrrolidone (PVP) and hydroxypropyl methylcellulose (HPMC) at different drug doses. Both in vitro and in vivo, the amorphous solid dispersions with the hydrophilic polymers PVP and HPMC led to higher areas under both, the in vitro dissolution and the plasma concentration-time curves (AUC) compared to crystalline and amorphous CCX for all doses. In contrast, the amorphous solid dispersion with the hydrophobic polymer PVA showed a lower AUC both in vitro and in vivo than crystalline CCX. For crystalline CCX and CCX:PVA, the in vitro AUC was limited by the low solubility of the drug and the slow release of the drug from the hydrophobic polymer, respectively. For the supersaturating formulations, amorphous CCX, CCX:PVP and CCX:HPMC, the in vitro performance was mainly dependent on the dissolution rate and precipitation/crystallization inhibition of the polymer. As expected, the crystallization tendency increased with increasing dose, and therefore the in vitro AUCs did not increase proportionally with dose. Even though the in vivo AUC for all formulations increased with increasing dose, the relative bioavailability decreased significantly, indicating that the supersaturating formulations also crystallized in vivo and that the absorption of CCX was solubility-limited. These findings underline the importance of evaluating relevant in vitro doses, in order to rationally assess the performance of amorphous solid dispersions and avoid confusion in early in vivo studies. Copyright © 2016 Elsevier B.V. All rights reserved.

  20. Airbrush Spray Coating of Amorphous Titanium Dioxide for Inverted Polymer Solar Cells

    Directory of Open Access Journals (Sweden)

    Luca La Notte

    2012-01-01

    Full Text Available One of the main topics of organic photovoltaics manufacturing is the need for simple, low cost, and large area compatible techniques. Solution-based processes are the best candidates to achieve this aim. Among these, airbrush spray coating has successfully applied to deposit both active and PEDOT layers of bulk-heterojunction solar cells. However, this technique is not yet sufficiently studied for interfacial layers (electron and hole transporting layers or optical spacers. In this paper, we show that amorphous titanium dioxide ( films, obtained with an airbrush from a solution of titanium (IV isopropoxide diluted in isopropanol, are successfully deposited on glass and PET substrates. Good surface covering results from the coalescence of droplets after optimizing the spray coating system. Simple inverted polymer solar cells are fabricated using as electron transporting layer obtaining encouraging electrical performances (% on glass/FTO and 0.7% on PET/ITO substrates.

  1. Optical properties of plasma deposited amorphous carbon nitride films on polymer substrates

    Energy Technology Data Exchange (ETDEWEB)

    Mohamed, S.H., E-mail: abo_95@yahoo.co [Physics Department, Faculty of Science, Sohag University, 82524 Sohag (Egypt); El-Hossary, F.M. [Physics Department, Faculty of Science, Sohag University, 82524 Sohag (Egypt); Gamal, G.A.; Kahlid, M.M. [Physics Department, Faculty of Science, South Valley University, 83523 Qena (Egypt)

    2010-01-01

    Amorphous carbon nitride thin films were deposited on polymer substrates using radio frequency (rf) plasma in a mixture of nitrogen (N{sub 2}) and acetylene (C{sub 2}H{sub 2}) gasses. The samples were prepared at different rf plasma power (350, 400, 450, 500, and 550 W), at constant plasma exposure time of 10 min, and constant N{sub 2}/C{sub 2}H{sub 2} ratio of 50%. The crystal structure and surface morphology of the prepared samples were examined using X-ray diffraction and atomic force microscopy analysis, respectively. The absence of the carbon nitride diffraction peaks confirms the amorphous nature of these films. The root mean square roughness of the films increased from 3.77 to 25.22 nm as the power increased from 350 to 550 W. The thickness and the deposition rate were found to increase with increasing plasma power. Over the whole studied wavelength range, from 200 to 2500 nm, the transmittance decreased with increasing plasma power. A shift in the onset of absorption towards higher wavelengths with increasing plasma power, indicating a decrease in the optical band gap, has been observed. The refractive index values were found to decrease while the extinction coefficient increased with increasing plasma power.

  2. Optical properties of plasma deposited amorphous carbon nitride films on polymer substrates

    Science.gov (United States)

    Mohamed, S. H.; El-Hossary, F. M.; Gamal, G. A.; Kahlid, M. M.

    2010-01-01

    Amorphous carbon nitride thin films were deposited on polymer substrates using radio frequency (rf) plasma in a mixture of nitrogen (N 2) and acetylene (C 2H 2) gasses. The samples were prepared at different rf plasma power (350, 400, 450, 500, and 550 W), at constant plasma exposure time of 10 min, and constant N 2/C 2H 2 ratio of 50%. The crystal structure and surface morphology of the prepared samples were examined using X-ray diffraction and atomic force microscopy analysis, respectively. The absence of the carbon nitride diffraction peaks confirms the amorphous nature of these films. The root mean square roughness of the films increased from 3.77 to 25.22 nm as the power increased from 350 to 550 W. The thickness and the deposition rate were found to increase with increasing plasma power. Over the whole studied wavelength range, from 200 to 2500 nm, the transmittance decreased with increasing plasma power. A shift in the onset of absorption towards higher wavelengths with increasing plasma power, indicating a decrease in the optical band gap, has been observed. The refractive index values were found to decrease while the extinction coefficient increased with increasing plasma power.

  3. Manganese Oxide Nanoparticle as a New p-Type Dopant for High-Performance Polymer Field-Effect Transistors.

    Science.gov (United States)

    Long, Dang Xuan; Choi, Eun-Young; Noh, Yong-Young

    2017-07-26

    We report a new p-type dopant, manganese oxide (Mn 3 O 4 ) nanoparticle, to enhance the performance of organic field-effect transistors (OFETs) with conjugated polymers, including poly(3-hexylthiophene-2,5-diyl), poly[[N,N 9-bis(2-octyldodecyl)-naphthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl]-alt-5,59-(2,29-bithiophene)], and poly[[2,5-bis(2-octyldodecyl)-2,3,5,6-tetrahydro-3,6-dioxopyrrolo[3,4-c]pyrrole-1,4-diyl]-alt-[[2,2'-(2,5-thiophene)bis-thieno(3,2b) thiophene]-5,5'-diyl

  4. Carrier polarity engineering in carbon nanotube field-effect transistors by induced charges in polymer insulator

    Science.gov (United States)

    Aikawa, Shinya; Kim, Sungjin; Thurakitseree, Theerapol; Einarsson, Erik; Inoue, Taiki; Chiashi, Shohei; Tsukagoshi, Kazuhito; Maruyama, Shigeo

    2018-01-01

    We present that the electrical conduction type in carbon nanotube field-effect transistors (CNT-FETs) can be converted by induced charges in a polyvinyl alcohol (PVA) insulator. When the CNT channels are covered with pure PVA, the FET characteristics clearly change from unipolar p-type to ambipolar. The addition of ammonium ions (NH4+) in the PVA leads to further conversion to unipolar n-type conduction. The capacitance - voltage characteristics indicate that a high density of positive charges is induced at the PVA/SiO2 interface and within the bulk PVA. Electrons are electrostatically accumulated in the CNT channels due to the presence of the positive charges, and thus, stable n-type conduction of PVA-coated CNT-FETs is observed, even under ambient conditions. The mechanism for conversion of the conduction type is considered to be electrostatic doping due to the large amount of positive charges in the PVA. A blue-shift of the Raman G-band peak was observed for CNTs coated with NH4+-doped PVA, which corresponds to unipolar n-type CNT-FET behavior. These results confirm that carrier polarity engineering in CNT-FETs can be achieved with a charged PVA passivation layer.

  5. Investigations into crazing in glassy amorphous polymers through molecular dynamics simulations

    Science.gov (United States)

    Venkatesan, Sudarkodi; Basu, Sumit

    2015-04-01

    In many glassy amorphous polymers, localisation of deformation during loading leads to crazes. Crazes are crack like features whose faces are bridged either by fibrils or a cellular network of voids and fibrils. While formation of crazes is aided by the presence of surface imperfections and embedded dust particles, in this work, we focus on intrinsic crazes that form spontaneously in the volume of the material. We perform carefully designed molecular dynamics simulations on well equilibrated samples of a model polymer with a view to gaining insights into certain incompletely understood aspects of the crazing process. These include genesis of the early nanovoids leading to craze nucleation, mechanisms of stabilising the cellular or fibrillar structure and the competition between chain scission and chain disentanglement in causing the final breakdown of the craze. Additionally, we identify and enumerate clusters of entanglement points with high functionality as effective topological constraints on macromolecular chains. We show that regions with low density of entanglement clusters serve as sites for nanovoid nucleation under high mean stress. Growth occurs by the repeated triggering of cavitation instabilities above a growing void. The growth of the void is aided by disentanglement in and flow of entanglements away from the cavitating region. Finally, for the chain lengths chosen, scission serves to supply short chains to the growing craze but breakdown occurs by complete disentanglement of the chains. In fact, most of the energy supplied to the material seems to be used in causing disentanglements and very little energy is required to create a stable fibril.

  6. Extended-gate field-effect transistor (EG-FET) with molecularly imprinted polymer (MIP) film for selective inosine determination.

    Science.gov (United States)

    Iskierko, Zofia; Sosnowska, Marta; Sharma, Piyush Sindhu; Benincori, Tiziana; D'Souza, Francis; Kaminska, Izabela; Fronc, Krzysztof; Noworyta, Krzysztof

    2015-12-15

    A novel recognition unit of chemical sensor for selective determination of the inosine, renal disfunction biomarker, was devised and prepared. For that purpose, inosine-templated molecularly imprinted polymer (MIP) film was deposited on an extended-gate field-effect transistor (EG-FET) signal transducing unit. The MIP film was prepared by electrochemical polymerization of bis(bithiophene) derivatives bearing cytosine and boronic acid substituents, in the presence of the inosine template and a thiophene cross-linker. After MIP film deposition, the template was removed, and was confirmed by UV-visible spectroscopy. Subsequently, the film composition was characterized by spectroscopic techniques, and its morphology and thickness were determined by AFM. The finally MIP film-coated extended-gate field-effect transistor (EG-FET) was used for signal transduction. This combination is not widely studied in the literature, despite the fact that it allows for facile integration of electrodeposited MIP film with FET transducer. The linear dynamic concentration range of the chemosensor was 0.5-50 μM with inosine detectability of 0.62 μM. The obtained detectability compares well to the levels of the inosine in body fluids which are in the range 0-2.9 µM for patients with diagnosed diabetic nephropathy, gout or hyperuricemia, and can reach 25 µM in certain cases. The imprinting factor for inosine, determined from piezomicrogravimetric experiments with use of the MIP film-coated quartz crystal resonator, was found to be 5.5. Higher selectivity for inosine with respect to common interferents was also achieved with the present molecularly engineered sensing element. The obtained analytical parameters of the devised chemosensor allow for its use for practical sample measurements. Copyright © 2015 Elsevier B.V. All rights reserved.

  7. Rheological analysis of itraconazole-polymer mixtures to determine optimal melt extrusion temperature for development of amorphous solid dispersion.

    Science.gov (United States)

    Solanki, Nayan; Gupta, Simerdeep Singh; Serajuddin, Abu T M

    2018-01-01

    The objective of this investigation was to develop a systematic method for the determination of optimal processing temperatures of drug-polymer mixtures for the development of amorphous solid dispersion (ASD) by melt extrusion. Since melt extrusion is performed at high temperature, it is essential that the processing temperature should be as low as possible to minimize degradation of drug and polymer, and yet the temperature should be high enough that the drug-polymer mixture attains certain viscosity that is extrudable and the drug dissolves in the molten polymer. By using itraconazole (ITZ) and polyvinyl caprolactam-polyvinyl acetate-polyethylene glycol graft co-polymer (Soluplus®, BASF) as, respectively, the model drug and the polymeric carrier, melt viscosities of drug-polymer mixtures with 5, 10, 20 and 30% ITZ were studied as functions of temperature and angular frequency. All these concentrations were below the miscibility limit as it was shown separately by film casting that ITZ was miscible with the polymer up to 40%. Since the angular frequency of a rheometer may not be high enough to simulate the shear rate within an extruder, torque analysis as a function of temperature during melt extrusion of selected drug-polymer mixtures was also conducted. The presence of dissolved ITZ had a plasticizing effect on the polymer used, and an intersection point around 150-155°C was observed, above which viscosities of drug-polymer mixtures were lower than that of polymer itself. Drug-polymer mixtures with 5 to 30% ITZ were extrudable at 150°C, and torque analysis showed that the mixture with 20% ITZ can be extruded even at 145°C. These temperatures were 17 to 22°C below the melting point of ITZ (167°C). ITZ dissolved due to the drug-polymer miscibility, the viscosity attained, and the shear rate generated. It was confirmed by PXRD and DSC that the extrudates were amorphous. Viscosity and miscibility of drug-polymer mixtures during melt extrusion were identified

  8. Fluorinated polymer-grafted organic dielectrics for organic field-effect transistors with low-voltage and electrical stability.

    Science.gov (United States)

    Kim, Kyunghun; Kim, Haekyoung; Kim, Se Hyun; Park, Chan Eon

    2015-07-14

    The electrical stabilities of low-voltage organic field-effect transistors (OFETs) were improved by applying graftable fluorinated polymer (gPFS) layers onto poly(4-vinyl phenol)-based cross-linked dielectrics (cPVP). As a result, a smooth and hydrophobic surface was formed, and the dielectric film displayed a low-leakage current density. The chemisorbed gPFS groups enabled the solution processing of an overlying 5,11-bis(triethylsilylethynyl)anthradithiophene semiconductor, which formed favorable terrace-like crystalline structures after solvent annealing. The top-contact OFETs showed superior operational stability compared to cPVP-based OFETs. Hysteresis was negligible, and the off-current of the transfer curve was one order of magnitude lower than that obtained from cPVP-based OFETs. The threshold voltage shift measured after a sustained gate bias stress for 1 h decreased significantly after introduction of the hydrophobic gPFS treatment; the energetic barrier to creating charge trapping sites increased, and the trap distribution narrowed, as supported by the stretched exponential function model.

  9. Improved Electron Transport with Reduced Contact Resistance in N-Doped Polymer Field-Effect Transistors with a Dimeric Dopant.

    Science.gov (United States)

    Wang, Rong; Guo, Yikun; Zhang, Di; Zhou, Huiqiong; Zhao, Dahui; Zhang, Yuan

    2018-01-15

    Attaining control on charge injection properties is significant for meaningful applications of organic field-effect transistors (OFETs). Here, molecular electron-doping is applied with an air-stable dimer dopant for n-type OFETs based on (naphthalene diimide-diketopyrrolopyrrole) polymer hosts. Through investigating the doping effect on contact and transport properties, it is found that the electron transport increases in n-doped OFETs at low doping regime with remaining large on/off ratios. These favorable meliorations are reconciled by the mitigated impacts of contact resistance and interfacial traps, as well as the surface morphology exhibiting features of increased ordering. The occurrence of doping in the presence of dimer dopants is evidenced by the observed shift of Fermi level toward vacuum level coupled with compositional analysis. Without applying vacuum-deposition-based contact doping, charge injection efficiencies are gained without losing OFET characteristics using the solution-based methodology. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Micron and sub-micron feature replication of amorphous polymers at elevated mold temperature without externally applied pressure

    International Nuclear Information System (INIS)

    Mosaddegh, Peiman; Angstadt, David C

    2008-01-01

    The focus of this study is on the ability of amorphous polymers to replicate micron and sub-micron features when molded at an elevated mold temperature without externally applied pressure. Molding was performed using three different types of amorphous polymers: cyclo-olefin copolymer (COC), polystyrene (PS) and poly (methyl methacrylate) (PMMA) on a silicon mold containing surface features as small as 700 nm in depth and aspect ratios ranging from 5 to 0.02. In this study, processing temperatures were selected in order to match the viscosity for all polymers used. Polymer viscosity was characterized via cone and plate rheometry and wettability was characterized via contact angle analysis to quantify interfacial effects. Feature replication was assessed using scanning electron microscopy (SEM) and atomic force microscopy (AFM) to compare the molded feature depth ratio. It was observed that for the features with an aspect ratio (depth/width) bigger than 2 the depth ratio of the molded parts decreases. PS shows the best replication because of high wettability behavior. PMMA shows the intermediate replication because of dipole–dipole interaction and its lower diffusion coefficient than PS. COC has the worse replication especially in low aspect ratio because of sticking to the silicon oxide layer. PS has the best surface roughness among all polymers

  11. A Thieno[2,3-b]pyridine-Flanked Diketopyrrolopyrrole Polymer as an n-Type Polymer Semiconductor for All-Polymer Solar Cells and Organic Field-Effect Transistors

    KAUST Repository

    Chen, Hung-Yang

    2017-12-28

    A novel fused heterocycle-flanked diketopyrrolopyrrole (DPP) monomer, thieno[2,3-b]pyridine diketopyrrolopyrrole (TPDPP), was designed and synthesized. When copolymerized with 3,4-difluorothiophene using Stille coupling polymerization, the new polymer pTPDPP-TF possesses a highly planar conjugated polymer backbone due to the fused thieno[2,3-b]pyridine flanking unit that effectively alleviates the steric hindrance with both the central DPP core and the 3,4-difluorothiophene repeat unit. This new polymer exhibits a high electron affinity (EA) of −4.1 eV and was successfully utilized as an n-type polymer semiconductor for applications in organic field-effect transistors (OFETs) and all polymer solar cells. A promising n-type charge carrier mobility of 0.1 cm2 V–1 s–1 was obtained in bottom-contact, top-gate OFETs, and a power conversion efficiency (PCE) of 2.72% with a high open-circuit voltage (VOC) of 1.04 V was achieved for all polymer solar cells using PTB7-Th as the polymer donor.

  12. Electrical analysis of amorphous corn starch-based polymer electrolyte membranes doped with LiI

    Science.gov (United States)

    Shukur, M. F.; Ibrahim, F. M.; Majid, N. A.; Ithnin, R.; Kadir, M. F. Z.

    2013-08-01

    In this work, polymer electrolytes have been prepared by doping starch with lithium iodide (LiI). The incorporation of 30 wt% LiI optimizes the room temperature conductivity of the electrolyte at (1.83 ± 0.47) × 10-4 S cm-1. Further conductivity enhancement to (9.56 ± 1.19) × 10-4 S cm-1 is obtained with the addition of 30 wt% glycerol. X-ray diffraction analysis indicates that the conductivity enhancement is due to the increase in amorphous content. The activation energy, Ea, of 70 wt% starch-30 wt% LiI electrolyte is 0.26 eV, while 49 wt% starch-21 wt% LiI-30 wt% glycerol electrolyte exhibits an Ea of 0.16 eV. Dielectric studies show that all the electrolytes obey non-Debye behavior. The power law exponent s is obtained from the variation of dielectric loss, ɛi, with frequency at different temperatures. The conduction mechanism of 70 wt% starch-30 wt% LiI electrolyte can be explained by the correlated barrier hopping model, while the conduction mechanism for 49 wt% starch-21 wt% LiI-30 wt% glycerol electrolyte can be represented by the quantum mechanical tunneling model.

  13. Chalcogenophene comonomer comparison in small band gap diketopyrrolopyrrole-based conjugated polymers for high-performing field-effect transistors and organic solar cells

    KAUST Repository

    Ashraf, Raja Shahid

    2015-01-28

    The design, synthesis, and characterization of a series of diketopyrrolopyrrole-based copolymers with different chalcogenophene comonomers (thiophene, selenophene, and tellurophene) for use in field-effect transistors and organic photovoltaic devices are reported. The effect of the heteroatom substitution on the optical, electrochemical, and photovoltaic properties and charge carrier mobilities of these polymers is discussed. The results indicate that by increasing the size of the chalcogen atom (S < Se < Te), polymer band gaps are narrowed mainly due to LUMO energy level stabilization. In addition, the larger heteroatomic size also increases intermolecular heteroatom-heteroatom interactions facilitating the formation of polymer aggregates leading to enhanced field-effect mobilities of 1.6 cm2/(V s). Bulk heterojunction solar cells based on the chalcogenophene polymer series blended with fullerene derivatives show good photovoltaic properties, with power conversion efficiencies ranging from 7.1-8.8%. A high photoresponse in the near-infrared (NIR) region with excellent photocurrents above 20 mA cm-2 was achieved for all polymers, making these highly efficient low band gap polymers promising candidates for use in tandem solar cells. (Graph Presented).

  14. Numerical Simulation and Experimental Investigation of the Viscoelastic Heating Mechanism in Ultrasonic Plasticizing of Amorphous Polymers for Micro Injection Molding

    Directory of Open Access Journals (Sweden)

    Bingyan Jiang

    2016-05-01

    Full Text Available Ultrasonic plasticizing of polymers for micro-injection molding has been proposed and studied for its unique potential in materials and energy-saving. In our previous work, we have demonstrated the characteristics of the interfacial friction heating mechanism in ultrasonic plasticizing of polymer granulates. In this paper, the other important heating mechanism in ultrasonic plasticizing, i.e., viscoelastic heating for amorphous polymer, was studied by both theoretical modeling and experimentation. The influence mechanism of several parameters, such as the initial temperature of the polymer, the ultrasonic frequency, and the ultrasonic amplitude, was investigated. The results from both numerical simulation and experimentation indicate that the heat generation rate of viscoelastic heating can be significantly influenced by the initial temperature of polymer. The glass transition temperature was found to be a significant shifting point in viscoelastic heating. The heat generation rate is relatively low at the beginning and can have a steep increase after reaching glass transition temperature. In comparison with the ultrasonic frequency, the ultrasonic amplitude has much greater influence on the heat generation rate. In light of the quantitative difference in the viscoelastic heating rate, the limitation of the numerical simulation was discussed in the aspect of the assumptions and the applied mathematical models.

  15. High operational and environmental stability of high-mobility conjugated polymer field-effect transistors through the use of molecular additives

    KAUST Repository

    Nikolka, Mark

    2016-12-12

    Due to their low-temperature processing properties and inherent mechanical flexibility, conjugated polymer field-effect transistors (FETs) are promising candidates for enabling flexible electronic circuits and displays. Much progress has been made on materials performance; however, there remain significant concerns about operational and environmental stability, particularly in the context of applications that require a very high level of threshold voltage stability, such as active-matrix addressing of organic light-emitting diode displays. Here, we investigate the physical mechanisms behind operational and environmental degradation of high-mobility, p-type polymer FETs and demonstrate an effective route to improve device stability. We show that water incorporated in nanometre-sized voids within the polymer microstructure is the key factor in charge trapping and device degradation. By inserting molecular additives that displace water from these voids, it is possible to increase the stability as well as uniformity to a high level sufficient for demanding industrial applications.

  16. Heterogeneous polymer modification: Polyolefin maleation in supercritical carbon dioxide and amorphous fluoropolymer surface modification

    Science.gov (United States)

    Hayes, Heather J.

    1999-11-01

    Three distinct heterogeneous polymer modification reactions are explored in this work. The first is a bulk reaction commonly conducted on polyolefins---the free radical addition of maleic anhydride. This reaction was run using supercritical carbon dioxide (SC CO2) as the solvent. The second was the chemical surface modification of an amorphous fluorocopolymer of tetrafluoroethylene and a perfluorodioxole monomer (Teflon AF). Several reactions were explored to reduce the surface of the fluorocopolymer for the enhancement of wettability. The last modification was also on Teflon AF and involved the physical modification of the surface through the transport polymerization of xylylene in order to synthesize a novel bilayer membrane. The bulk maleation of poly-4-methyl-1-pentene (PMP) was the focus of the first project. SC CO2 was utilized as both solvent and swelling agent to promote this heterogeneous reaction and led to successful grafting of anhydride groups on both PMP and linear low density polyethylene. Varying the reaction conditions and reagent concentrations allowed optimization of the reaction. The grafted anhydride units were found to exist as single maleic and succinic grafts, and the PMP became crosslinked upon maleation. The surface of a fluoropolymer can be difficult to alter. An examination of three reactions was made to determine the reactivity of Teflon AF: sodium naphthalenide treatment (Na-Nap), aluminum metal modification through deposition and dissolution, and mercury/ammonia photosensitization. The fluorocopolymer with the lower perfluorodioxole percentage was found to be more reactive towards modification with the Na-Nap treatment. The other modification reactions appeared to be nearly equally reactive toward both fluorocopolymers. The functionality of the Na-Nap-treated surface was examined in detail with the use of several derivatization reactions. In the final project, an asymmetric gas separation membrane was synthesized using Teflon AF as

  17. Enzymatically Catalyzed Degradation of Biodegradable Polymers Investigated by Means of a Semiconductor-based Field-effect Sensor

    OpenAIRE

    Schusser, S.; Bäcker, M.; Krischer, M.; Wenzel, L.; Leinhos, M.; Poghossian, A.; Biselli, M.; Wagner, P.; Schöning, M.J.

    2014-01-01

    A semiconductor field-effect device has been used for an enzymatically catalyzed degradation of biopolymers for the first time. This novel technique is capable to monitor the degradation process of multiple samples in situ and in real-time. As model system, the degradation of the biopolymer poly(D, L-lactic acid) has been monitored in the degradation medium containing the enzyme lipase from Rhizomucor miehei. The obtained results demonstrate the potential of capacitive field-effect sensors fo...

  18. 25th anniversary article: isoindigo-based polymers and small molecules for bulk heterojunction solar cells and field effect transistors.

    Science.gov (United States)

    Wang, Ergang; Mammo, Wendimagegn; Andersson, Mats R

    2014-03-26

    Driven by the potential advantages and promising applications of organic solar cells, donor-acceptor (D-A) polymers have been intensively investigated in the past years. One of the strong electron-withdrawing groups that were widely used as acceptors for the construction of D-A polymers for applications in polymer solar cells and FETs is isoindigo. The isoindigo-based polymer solar cells have reached efficiencies up to ∼7% and hole mobilities as high as 3.62 cm(2) V(-1) s(-1) have been realized by FETs based on isoindigo polymers. Over one hundred isoindigo-based small molecules and polymers have been developed in only three years. This review is an attempt to summarize the structures and properties of the isoindigo-based polymers and small molecules that have been reported in the literature since their inception in 2010. Focus has been given only to the syntheses and device performances of those polymers and small molecules that were designed for use in solar cells and FETs. Attempt has been made to deduce structure-property relationships that would guide the design of isoindigo-based materials. It is expected that this review will present useful guidelines for the design of efficient isoindigo-based materials for applications in solar cells and FETs. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. The effect of metallization contact resistance on the measurement of the field effect mobility of long-channel unannealed amorphous In–Zn–O thin film transistors

    International Nuclear Information System (INIS)

    Lee, Sunghwan; Park, Hongsik; Paine, David C.

    2012-01-01

    The effect of contact resistance on the measurement of the field effect mobility of compositionally homogeneous channel indium zinc oxide (IZO)/IZO metallization thin film transistors (TFTs) is reported. The TFTs studied in this work operate in depletion mode as n-channel field effect devices with a field effect mobility calculated in the linear regime (μ FE ) of 20 ± 1.9 cm 2 /Vs and similar of 18 ± 1.3 cm 2 /Vs when calculated in the saturation regime (μ FE sat ). These values, however, significantly underestimate the channel mobility since a large part of the applied drain voltage is dropped across the source/drain contact interface. The transmission line method was employed to characterize the contact resistance and it was found that the conducting-IZO/semiconducting-IZO channel contact is highly resistive (specific contact resistance, ρ C > 100 Ωcm 2 ) and, further, this contact resistance is modulated with applied gate voltage. Accounting for the contact resistance (which is large and modulated by gate voltage), the corrected μ FE is shown to be 39 ± 2.6 cm 2 /Vs which is consistent with Hall mobility measurements of high carrier density IZO.

  20. Influence of mechanically-induced dilatation on the shape memory behavior of amorphous polymers at large deformation

    Science.gov (United States)

    Hanzon, Drew W.; Lu, Haibao; Yakacki, Christopher M.; Yu, Kai

    2018-01-01

    In this study, we explore the influence of mechanically-induced dilatation on the thermomechanical and shape memory behavior of amorphous shape memory polymers (SMPs) at large deformation. The uniaxial tension, glass transition, stress relaxation and free recovery behaviors are examined with different strain levels (up to 340% engineering strain). A multi-branched constitutive model that incorporates dilatational effects on the polymer relaxation time is established and applied to assist in discussions and understand the nonlinear viscoelastic behaviors of SMPs. It is shown that the volumetric dilatation results in an SMP network with lower viscosity, faster relaxation, and lower Tg. The influence of the dilatational effect on the thermomechanical behaviors is significant when the polymers are subject to large deformation or in a high viscosity state. The dilation also increases the free recovery rate of SMP at a given recovery temperature. Even though the tested SMPs are far beyond their linear viscoelastic region when a large programming strain is applied, the free recovery behavior still follows the time-temperature superposition (TTSP) if the dilatational effect is considered during the transformation of time scales; however, if the programming strain is different, TTSP fails in predicting the recovery behavior of SMPs because the network has different entropy state and driving force during shape recovery. Since most soft active polymers are subject to large deformation in practice, this study provides a theoretical basis to better understand their nonlinear viscoelastic behaviors, and optimize their performance in engineering applications.

  1. Chain conformation-dependent thermal conductivity of amorphous polymer blends: the impact of inter- and intra-chain interactions.

    Science.gov (United States)

    Wei, Xingfei; Zhang, Teng; Luo, Tengfei

    2016-11-30

    Polymers with high thermal conductivities are of great interest for both scientific research and industrial applications. In this study, model amorphous polymer blends are studied using molecular dynamics simulations. We have examined the effects of inter- and intra-chain interactions on the molecular-level conformations of the blends, which in turn impact their thermal conductivity. It is found that the thermal conductivity of polymer blends is strongly related to the molecular conformation, especially the spatial extent of the molecular chains indicated by their radius of gyration. Tuning the intra-chain van der Waals (vdW) interaction leads to different molecular structures of the minor component in the binary blend, but the thermal conductivity is not changed. However, increasing the inter-chain vdW interactions between the major and the minor components will increase the thermal conductivity of the blend, which is due to the conformation change in the major component that leads to enhanced thermal transport along the chain backbone through the intra-chain bonding interactions. The fundamental structure-property relationship from this study may provide useful guidance for designing and synthesizing polymer blends with desirable thermal conductivity.

  2. Monitoring of the Enzymatically Catalyzed Degradation of Biodegradable Polymers by Means of Capacitive Field-Effect Sensors.

    Science.gov (United States)

    Schusser, Sebastian; Krischer, Maximilian; Bäcker, Matthias; Poghossian, Arshak; Wagner, Patrick; Schöning, Michael J

    2015-07-07

    Designing novel or optimizing existing biodegradable polymers for biomedical applications requires numerous tests on the effect of substances on the degradation process. In the present work, polymer-modified electrolyte-insulator-semiconductor (PMEIS) sensors have been applied for monitoring an enzymatically catalyzed degradation of polymers for the first time. The thin films of biodegradable polymer poly(D,L-lactic acid) and enzyme lipase were used as a model system. During degradation, the sensors were read-out by means of impedance spectroscopy. In order to interpret the data obtained from impedance measurements, an electrical equivalent circuit model was developed. In addition, morphological investigations of the polymer surface have been performed by means of in situ atomic force microscopy. The sensor signal change, which reflects the progress of degradation, indicates an accelerated degradation in the presence of the enzyme compared to hydrolysis in neutral pH buffer media. The degradation rate increases with increasing enzyme concentration. The obtained results demonstrate the potential of PMEIS sensors as a very promising tool for in situ and real-time monitoring of degradation of polymers.

  3. Micropatterning and transferring of polymeric semiconductor thin films by hot lift-off and polymer bonding lithography in fabrication of organic field effect transistors (OFETs) on flexible substrate

    Energy Technology Data Exchange (ETDEWEB)

    Yu Xinhong; Wang Zhe; Yu Sunyang [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, 5625 Renmin Street, Changchun 130022 (China); Ma Dongge, E-mail: mdg1014@ciac.jl.cn [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, 5625 Renmin Street, Changchun 130022 (China); Han Yanchun, E-mail: ychan@ciac.jl.cn [State Key Laboratory of Polymer Physics and Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, 5625 Renmin Street, Changchun 130022 (China)

    2011-09-01

    Micropatterning and transferring of polymeric semiconductor thin films by hot lift-off and polymer bonding lithography in fabrication of OFETs with polymeric dielectric on the flexible substrate was proposed. The desired polymeric semiconductor patterns were fabricated on the flat polydimethylsiloxane (PDMS) surface with a selective lift-off method we proposed previously. The isolated and well defined polymeric semiconductor patterns left on the flat PDMS surface can be further transferred to the gate polymeric dielectric surface by polymer bonding lithography due to the low interfacial energy of PDMS. The transistor fabricated with this 'dry' process has a higher field-effect mobility compared with that using spin coated semiconductor layer.

  4. Study of amorphous semiconductors doped with rare earths (Gd and Er) and conducting polymers by EPR techniques and magnetic susceptibility

    International Nuclear Information System (INIS)

    Sercheli, Mauricio da Silva

    1999-01-01

    This thesis involves the study of amorphous semiconductors and conducting polymers, which have been characterized by EPR and magnetic susceptibility measurements, and to a lesser extent by Raman spectroscopy and RBS. The semiconductors were studied using thin films of silicon doped with rare earth metals, e.g. erbium and gadolinium, which had their magnetic properties studied. Using these studies we could determine the state of valence of the rare earths as well as their concentrations in the silicon matrix. According to our results, the valence of the rare earth metal ions is 3+, and we were able to conclude that 4f electronic shells could not be used for the calculation of the conducting band in this system. Furthermore, the analysis of the data on the magnetic susceptibility of the Er 3+ ion with cubic crystalline acting field, gave us the opportunity to estimate the overall splitting of their electronic states for the first time. The conducting polymers were studied using samples of poly(3-methylthiophene) doped with ClO 4 - , which show a phase transition in the range of 230 K to 130 K. The electron paramagnetic resonance also gives important information on the crystallization, doping level and the presence of polarons or bipolarons in conducting polymers. (author)

  5. Simultaneous Improvement of Hole and Electron Injection in Organic Field-effect Transistors by Conjugated Polymer-wrapped Carbon Nanotube Interlayers

    Science.gov (United States)

    Lee, Seung-Hoon; Khim, Dongyoon; Xu, Yong; Kim, Juhwan; Park, Won-Tae; Kim, Dong-Yu; Noh, Yong-Young

    2015-05-01

    Efficient charge injection is critical for flexible organic electronic devices such as organic light-emitting diodes (OLEDs) and field-effect transistors (OFETs). Here, we investigated conjugated polymer-wrapped semiconducting single-walled carbon nanotubes (s-SWNTs) as solution-processable charge-injection layers in ambipolar organic field-effect transistors with poly(thienylenevinylene-co-phthalimide)s. The interlayers were prepared using poly(9,9-di-n-octylfluorene-alt-benzothiadiazole) (F8BT) or poly(9,9-dioctylfluorene) (PFO) to wrap s-SWNTs. In the contact-limited ambipolar OFETs, the interlayer led to significantly lower contact resistance (Rc) and increased mobilities for both holes and electrons. The resulting PTVPhI-Eh OFETs with PFO-wrapped s-SWNT interlayers showed very well-balanced ambipolar transport properties with a hole mobility of 0.5 cm2V-1S-1 and an electron mobility of 0.5 cm2V-1S-1 in linear regime. In addition, the chirality of s-SWNTs and kind of wrapping of conjugated polymers are not critical to improving charge-injection properties. We found that the improvements caused by the interlayer were due to the better charge injection at the metal/organic semiconductor contact interface and the increase in the charge concentration through a detailed examination of charge transport with low-temperature measurements. Finally, we successfully demonstrated complementary ambipolar inverters incorporating the interlayers without excessive patterning.

  6. A phenomenological formulation for the shape/temperature memory effect in amorphous polymers with multi-stress components

    Science.gov (United States)

    Lu, Haibao; Wang, Xiaodong; Yu, Kai; Huang, Wei Min; Yao, Yongtao; Leng, Jinsong

    2017-09-01

    By means of combining the influence of temperature and strain rate, and based on the cooperative Eyring model, a phenomenological formulation for the shape memory effect and temperature memory effect of an amorphous shape memory polymer (SMP) is proposed. The internal stress and stored mechanical energy are correlated to shape/temperature memory behaviours below and above the glass transition temperature. The working mechanism and fundamentals for the chemo-responsive shape memory behaviour in SMPs are further investigated in terms of the activation enthalpy parameter for inductive depression. Simulation using the proposed model is compared with the experimental results reported in the literature. Predictions are also made using the proposed model. This phenomenological framework is expected to provide a powerful tool for investigating the underlying thermomechanics that originate in the movement of cooperative segments and segmental relaxations in SMPs.

  7. Hysteresis behaviour of low-voltage organic field-effect transistors employing high dielectric constant polymer gate dielectrics

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Se Hyun; Yun, Won Min; Kwon, Oh-Kwan; Hong, Kipyo; Yang, Chanwoo; Park, Chan Eon [POSTECH Organic Electronics Laboratory, Department of Chemical Engineering, Pohang University of Science and Technology, Pohang 790-784 (Korea, Republic of); Choi, Woon-Seop, E-mail: cep@postech.ac.k, E-mail: wschoi@hoseo.ed [School of Display Engineering, Hoseo University, Asan City, Chungnam 336-795 (Korea, Republic of)

    2010-11-24

    Here, we report on the fabrication of low-voltage-operating pentacene-based organic field-effect transistors (OFETs) that utilize crosslinked cyanoethylated poly(vinyl alcohol) (CR-V) gate dielectrics. The crosslinked CR-V-based OFET could be operated successfully at low voltages (below 4 V), but abnormal behaviour during device operation, such as uncertainty in the field-effect mobility ({mu}) and hysteresis, was induced by the slow polarization of moieties embedded in the gate dielectric (e.g. polar functionalities, ionic impurities, water and solvent molecules). In an effort to improve the stability of OFET operation, we measured the dependence of {mu} and hysteresis on dielectric thickness, CR-V crosslinking conditions and sweep rate of the gate bias. The influence of the CR-V surface properties on {mu}, hysteresis, and the structural and morphological features of the pentacene layer grown on the gate dielectric was characterized and compared with the properties of pentacene grown on a polystyrene surface.

  8. Influence of polymer molecular weight on in vitro dissolution behavior and in vivo performance of celecoxib:PVP amorphous solid dispersions

    DEFF Research Database (Denmark)

    Knopp, Matthias Manne; Nguyen, Julia Hoang; Becker, Christian

    2016-01-01

    In this study, the influence of the molecular weight of polyvinylpyrrolidone (PVP) on the non-sink in vitro dissolution and in vivo performance of celecoxib (CCX):PVP amorphous solid dispersions were investigated. The dissolution rate of CCX from the amorphous solid dispersions increased with dec...... a ranking between the different formulations. In conclusion, the findings of this study demonstrated that the in vitro and in vivo performance of CCX:PVP amorphous solid dispersions were significantly controlled by the molecular weight of the polymer.......In this study, the influence of the molecular weight of polyvinylpyrrolidone (PVP) on the non-sink in vitro dissolution and in vivo performance of celecoxib (CCX):PVP amorphous solid dispersions were investigated. The dissolution rate of CCX from the amorphous solid dispersions increased...... with decreasing PVP molecular weight and crystallization inhibition was increased with increasing molecular weight of PVP, but reached a maximum for PVP K30. This suggested that the crystallization inhibition was not proportional with molecular weight of the polymer, but rather there was an optimal molecular...

  9. Hot melt extruded amorphous solid dispersion of posaconazole with improved bioavailability: investigating drug-polymer miscibility with advanced characterisation.

    Science.gov (United States)

    Fule, Ritesh; Amin, Purnima

    2014-01-01

    Invasive antifungal infections are reasons for morbidity and mortality in immunogenic patients worldwide. Posaconazole is a most promising antifungal agent against all types of invasive infections with high % of cure rate. The marketed suspension formulation has low bioavailability and is needed to be taken with food. In this paper, PCZ hot melt extruded amorphous solid dispersion (SD) with immediate release and improved bioavailability was prepared using Soluplus (Sol) as primary carrier for solubilization. Surfactants such as PEG 400, Lutrol F27, Lutrol F68, and TPGS are also used in combination with Soluplus to improve the physicochemical performance of the formulation when it comes in contact with GI (gastrointestinal) fluid. Drug-polymer miscibility of SD was investigated using advanced techniques. In the in vivo study, the AUC(0-72) and C(max) of PCZ/Soluplus were 11.5 and 11.74 time higher than those of pure PCZ. The formulation of the extrudate SD had an AUC(0-72) and C(max) higher than those with the commercial capsule (Noxafil). Molecular dynamic (MD) simulation studies were carried out using in silico molecular modelling to understand the drug-polymer intermolecular behaviour. The results of this research ensure enhanced dissolution and bioavailability of the solid dispersion of PCZ prepared by HME compared with the PCZ suspension.

  10. The relation between relaxed enthalpy and volume during physical aging of amorphous polymers and selenium

    Czech Academy of Sciences Publication Activity Database

    Slobodian, P.; Říha, Pavel; Rychwalski, R. W.; Emri, I.; Sáha, P.; Kubát, J.

    2006-01-01

    Roč. 42, č. 10 (2006), s. 2824-2837 ISSN 0014-3057 R&D Projects: GA AV ČR IAA2060401 Institutional research plan: CEZ:AV0Z20600510 Keywords : Enthalpy relaxation * Polymer aging Subject RIV: BJ - Thermodynamics Impact factor: 2.113, year: 2006

  11. Computational modeling of rubber-toughening in amorphous thermoplastic polymers: a review

    NARCIS (Netherlands)

    van der Giessen, Erik; Seelig, Thomas

    2015-01-01

    The fracture behavior of rubber-toughened polymers is governed by two dissipative microscopic deformation and damage mechanisms: matrix shear yielding and crazing. These mechanisms are strongly interconnected with the eventual cavitation of the fine dispersed rubber particles. The present work

  12. Development of amorphous dispersions of artemether with hydrophilic polymers via spray drying: Physicochemical and in silico studies

    Directory of Open Access Journals (Sweden)

    Jaywant N. Pawar

    2016-06-01

    Full Text Available Artemether (ARM is a poorly water soluble and poorly permeable drug effective against acute and severe falciparum malaria, hence there is a strong need to improve its solubility. The objective of the study was to enhance the solubility and dissolution rate of ARM by preparation of solid dispersions using spray-drying technique. Solid dispersions of ARM were prepared with Soluplus, Kollidon VA 64, HPMC and Eudragit EPO at weight ratios of 1:1, 1:2, 1:3 using spray drying technology, and characterized by Fourier transform infrared spectroscopy, differential scanning calorimetry (DSC, and X-ray powder diffraction (XRD to identify the physicochemical interaction between drug and carrier, as well as effect on dissolution. The prepared solid dispersion of ARM with polymers showed reduced crystallinity as compared to neat ARM, which was confirmed by DSC and XRD. Drug/polymer interactions were studied in-silico by docking and molecular dynamics which indicated formation of van der Waals type of interactions of ARM with the polymers. Based on solubility studies, the optimum drug/Soluplus ratio was found to be 1:3. The dissolution studies of formulation SD3 showed highest drug release up to 82% compared to neat ARM giving only 20% at 60 minutes. The spray-dried products were free of crystalline ARM; possessed higher dissolution rates, and were stable over a period according to ICH guidelines. These findings suggest that an amorphous solid dispersion of ARM could be a viable option for enhancing the dissolution rate of ARM.

  13. Solvent-shift strategy to identify suitable polymers to inhibit humidity-induced solid-state crystallization of lacidipine amorphous solid dispersions.

    Science.gov (United States)

    Sun, Mengchi; Wu, Chunnuan; Fu, Qiang; Di, Donghua; Kuang, Xiao; Wang, Chao; He, Zhonggui; Wang, Jian; Sun, Jin

    2016-04-30

    The solvent-shift strategy was used to identify appropriate polymers that inhibit humidity-induced solid-state crystallization of amorphous solid dispersions (ASDs). Lacidipine with the polymers, PVP-K30, HPMC-E5 or Soluplus, were combined to form amorphous solid dispersions prepared by solvent evaporation. The formulations were characterized by differential scanning calorimetry (DSC), powder X-ray diffraction (PXRD), and Fourier-transform infrared spectroscopy (FT-IR) and were subjected to in vitro dissolution testing. The moisture had a significant impact on the amount dissolved for the solid dispersions. Molecular docking studies established that hydrogen bonding was critical for the stabilization of the solid dispersions. The rank order of the binding energy of the drug-polymer association was Soluplus (-6.21 kcal/mol)>HPMC-E5 (-3.21 kcal/mol)>PVP-K30 (-2.31 kcal/mol). PVP-K30 had the highest water uptake among the polymers, as did ASD system of lacidipine-PVP-K30 ASDs. In the Soluplus ASDs, with its strong drug-polymer interactions and low water uptake, moisture-induced solid-state crystallization was not observed. Copyright © 2016 Elsevier B.V. All rights reserved.

  14. The effects of polymer carrier, hot melt extrusion process and downstream processing parameters on the moisture sorption properties of amorphous solid dispersions.

    Science.gov (United States)

    Feng, Xin; Vo, Anh; Patil, Hemlata; Tiwari, Roshan V; Alshetaili, Abdullah S; Pimparade, Manjeet B; Repka, Michael A

    2016-05-01

    The aim of this study was to evaluate the effect of polymer carrier, hot melt extrusion and downstream processing parameters on the water uptake properties of amorphous solid dispersions. Three polymers and a model drug were used to prepare amorphous solid dispersions utilizing the hot melt extrusion technology. The sorption-desorption isotherms of solid dispersions and their physical mixtures were measured by the dynamic vapour sorption system, and the effects of polymer hydrophobicity, hygroscopicity, molecular weight and the hot melt extrusion process were investigated. Fourier transform infrared (FTIR) imaging was performed to understand the phase separation driven by the moisture. Solid dispersions with polymeric carriers with lower hydrophilicity, hygroscopicity and higher molecular weight could sorb less moisture under the high relative humidity (RH) conditions. The water uptake ability of polymer-drug solid dispersion systems were decreased compared with the physical mixture after hot melt extrusion, which might be due to the decreased surface area and porosity. The FTIR imaging indicated that the homogeneity of the drug molecularly dispersed within the polymer matrix was changed after exposure to high RH. Understanding the effect of formulation and processing on the moisture sorption properties of solid dispersions is essential for the development of drug products with desired physical and chemical stability. © 2015 Royal Pharmaceutical Society.

  15. Metallic glasses: viable tool materials for the production of surface microstructures in amorphous polymers by micro-hot-embossing

    International Nuclear Information System (INIS)

    Henann, David L; Srivastava, Vikas; Taylor, Hayden K; Hale, Melinda R; Hardt, David E; Anand, Lallit

    2009-01-01

    Metallic glasses possess unique mechanical properties which make them attractive materials for fabricating components for a variety of applications. For example, the commercial Zr-based metallic glasses possess high tensile strengths (≈2.0 GPa), good fracture toughnesses (≈10–50 MPa√m) and good wear and corrosion resistances. A particularly important characteristic of metallic glasses is their intrinsic homogeneity to the nanoscale because of the absence of grain boundaries. This characteristic, coupled with their unique mechanical properties, makes them ideal materials for fabricating micron-scale components, or high-aspect-ratio micro-patterned surfaces, which may in turn be used as dies for the hot-embossing of polymeric microfluidic devices. In this paper we consider a commercially available Zr-based metallic glass which has a glass transition temperature of T g ≈ 350 °C and describe the thermoplastic forming of a tool made from this material, which has the (negative) microchannel pattern for a simple microfluidic device. This tool was successfully used to produce the microchannel pattern by micro-hot-embossing of the amorphous polymers poly(methyl methacrylate) (T g ≈ 115 °C) and Zeonex-690R (T g ≈ 136 °C) above their glass transition temperatures. The metallic glass tool was found to be very robust, and it was used to produce hundreds of high-fidelity micron-scale embossed patterns without degradation or failure

  16. The peculiar behavior of the glass transition temperature of amorphous drug-polymer films coated on inert sugar spheres.

    Science.gov (United States)

    Dereymaker, Aswin; Van Den Mooter, Guy

    2015-05-01

    Fluid bed coating has been proposed in the past as an alternative technology for manufacturing of drug-polymer amorphous solid dispersions, or so-called glass solutions. It has the advantage of being a one-step process, and thus omitting separate drying steps, addition of excipients, or manipulation of the dosage form. In search of an adequate sample preparation method for modulated differential scanning calorimetry analysis of beads coated with glass solutions, glass transition broadening and decrease of the glass transition temperature (Tg ) were observed with increasing particle size of crushed coated beads and crushed isolated films of indomethacin (INDO) and polyvinylpyrrolidone (PVP). Substituting INDO with naproxen gave comparable results. When ketoconazole was probed or the solvent in INDO-PVP films was switched to dichloromethane (DCM) or a methanol-DCM mixture, two distinct Tg regions were observed. Small particle sizes had a glass transition in the high Tg region, and large particle sizes had a glass transition in the low Tg region. This particle size-dependent glass transition was ascribed to different residual solvent amounts in the bulk and at the surface of the particles. A correlation was observed between the deviation of the Tg from that calculated from the Gordon-Taylor equation and the amount of residual solvent at the Tg of particles with different sizes. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

  17. Evaluation of drug load and polymer by using a 96-well plate vacuum dry system for amorphous solid dispersion drug delivery.

    Science.gov (United States)

    Chiang, Po-Chang; Ran, Yingqing; Chou, Kang-Jye; Cui, Yong; Sambrone, Amy; Chan, Connie; Hart, Ryan

    2012-06-01

    It is well recognized that poor dissolution rate and solubility of drug candidates are key limiting factors for oral bioavailability. While numerous technologies have been developed to enhance solubility of the drug candidates, poor water solubility continuously remains a challenge for drug delivery. Among those technologies, amorphous solid dispersions (SD) have been successfully employed to enhance both dissolution rate and solubility of poorly water-soluble drugs. This research reports a high-throughput screening technology developed by utilizing a 96-well plate system to identify optimal drug load and polymer using a solvent casting approach. A minimal amount of drug was required to evaluate optimal drug load in three different polymers with respect to solubility improvement and solid-state stability of the amorphous drug-polymer system. Validation of this method was demonstrated with three marketed drugs as well as with one internal compound. Scale up of the internal compound SD by spray drying further confirmed the validity of this method, and its quality was comparable to a larger scale process. Here, we demonstrate that our system is highly efficient, cost-effective, and robust to evaluate the feasibility of spray drying technology to produce amorphous solid dispersions.

  18. Donor-Acceptor Copolymers Based on Thermally Cleavable Indigo, Isoindigo, and DPP Units: Synthesis, Field Effect Transistors, and Polymer Solar Cells.

    Science.gov (United States)

    Liu, Chunchen; Dong, Sheng; Cai, Ping; Liu, Peng; Liu, Shengjian; Chen, Junwu; Liu, Feng; Ying, Lei; Russell, Thomas P; Huang, Fei; Cao, Yong

    2015-05-06

    A series of donor-acceptor type of π-conjugated copolymers based on tert-butoxycarbonyl (t-Boc) substituted indigo, isoindigo or diketopyrrolopyrrole as the acceptor unit and a benzodithiophene derivative as the donor unit was designed and synthesized. These copolymers can be readily dissolved in organic solvents and can produce uniform films by solution deposition. Thermal treatment of copolymer films at 200 °C for 10 min resulted in elimination of t-Boc side groups in nearly quantitative yield as suggested by thermogravimetric analysis and Fourier transform infrared spectroscopy. The elimination of the bulky t-Boc side groups resulted in the emergence of N-H···O═C hydrogen bonding interactions by virtue of the lactam structures of the indigo, isoindigo and diketopyrrolopyrrole units. Of particular interests is the distinctly increased field-effect mobility of these copolymers after thermal treatment, which may arise from the enhanced coplanarity and intermolecular ordering of the indigo, isoindigo or diketopyrrolopyrrole units after elimination of the bulky t-Boc side groups. These results demonstrate that the incorporation of latent side groups provides a viable strategy to construct conjugated polymers that can attain more ordered intermolecular stacking by simple thermal treatments. On the other hand, despite the thermal cleavage of t-Boc groups can also lead to increased ordering of polymer chains when blending with [6,6]-phenyl C71 butyric acid methyl ester, the photovoltaic performances of the resulting bulk heterojunction solar cells did not obviously increase due to the serious phase separation and coarsening of the film morphology.

  19. Tuning the Work Function of Printed Polymer Electrodes by Introducing a Fluorinated Polymer To Enhance the Operational Stability in Bottom-Contact Organic Field-Effect Transistors.

    Science.gov (United States)

    Kim, Se Hyun; Kim, Jiye; Nam, Sooji; Lee, Hwa Sung; Lee, Seung Woo; Jang, Jaeyoung

    2017-04-12

    Poly(3,4-ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) is a promising electrode material for organic electronic devices due to its high conductivity, good mechanical flexibility, and feasibility of easy patterning with various printing methods. The work function of PEDOT:PSS needs to be increased for efficient hole injection, and the addition of a fluorine-containing material has been reported to increase the work function of PEDOT:PSS. However, it remains a challenge to print PEDOT:PSS electrodes while simultaneously tuning their work functions. Here, we report work function tunable PEDOT:PSS/Nafion source/drain electrodes formed by electrohydrodynamic printing technique with PEDOT:PSS/Nafion mixture solutions for highly stable bottom-contact organic field-effect transistors (OFETs). The surface properties and work function of the printed electrode can be controlled by varying the Nafion ratio, due to the vertical phase separation of the PEDOT:PSS/Nafion. The PEDOT:PSS/Nafion electrodes exhibit a low hole injection barrier, which leads to efficient charge carrier injection from the electrode to the semiconductor. As a result, pentacene-based OFETs with PEDOT:PSS/Nafion electrodes show increased charge carrier mobilities of 0.39 cm 2 /(V·s) compared to those of devices with neat PEDOT:PSS electrodes (0.021 cm 2 /(V·s)). Moreover, the gate-bias stress stability of the OFETs is remarkably improved by employing PEDOT:PSS/Nafion electrodes, as demonstrated by a reduction of the threshold voltage shift from -1.84 V to -0.28 V.

  20. Supersaturation, nucleation, and crystal growth during single- and biphasic dissolution of amorphous solid dispersions: polymer effects and implications for oral bioavailability enhancement of poorly water soluble drugs.

    Science.gov (United States)

    Sarode, Ashish L; Wang, Peng; Obara, Sakae; Worthen, David R

    2014-04-01

    The influence of polymers on the dissolution, supersaturation, crystallization, and partitioning of poorly water soluble compounds in biphasic media was evaluated. Amorphous solid dispersions (ASDs) containing felodipine (FLD) and itraconazole (ITZ) were prepared by hot melt mixing (HMM) using various polymers. The ASDs were analyzed using powder X-ray diffraction (PXRD), differential scanning calorimetry (DSC), and HPLC. Amorphous drug conversion was confirmed using DSC and PXRD, and drug stability by HPLC. Single- and biphasic dissolution studies of the ASDs with concurrent dynamic light scattering (DLS) and polarized light microscopic (PLM) analysis of precipitated drugs were performed. HPLC revealed no HMM-induced drug degradation. Maximum partitioning into the organic phase was dependent upon the degree of supersaturation. Although the highest supersaturation of FLD was attained using Eudragit® EPO and AQOAT® AS-LF with better nucleation and crystal growth inhibition using the latter, higher partitioning of the drug into the organic phase was achieved using Pharmacoat® 603 and Kollidon® VA-64 by maintaining supersaturation below critical nucleation. Critical supersaturation for ITZ was surpassed using all of the polymers, and partitioning was dependent upon nucleation and crystal growth inhibition in the order of Pharmacoat® 603>Eudragit® L-100-55>AQOAT® AS-LF. HMM drug-polymer systems that prevent drug nucleation by staying below critical supersaturation are more effective for partitioning than those that achieve the highest supersaturation. Copyright © 2013 Elsevier B.V. All rights reserved.

  1. Understanding API-polymer proximities in amorphous stabilized composite drug products using fluorine-carbon 2D HETCOR solid-state NMR.

    Science.gov (United States)

    Abraham, Anuji; Crull, George

    2014-10-06

    A simple and robust method for obtaining fluorine-carbon proximities was established using a (19)F-(13)C heteronuclear correlation (HETCOR) two-dimensional (2D) solid-state nuclear magnetic resonance (ssNMR) experiment under magic-angle spinning (MAS). The method was applied to study a crystalline active pharmaceutical ingredient (API), avagacestat, containing two types of fluorine atoms and its API-polymer composite drug product. These results provide insight into the molecular structure, aid with assigning the carbon resonances, and probe API-polymer proximities in amorphous spray dried dispersions (SDD). This method has an advantage over the commonly used (1)H-(13)C HETCOR because of the large chemical shift dispersion in the fluorine dimension. In the present study, fluorine-carbon distances up to 8 Å were probed, giving insight into the API structure, crystal packing, and assignments. Most importantly, the study demonstrates a method for probing an intimate molecular level contact between an amorphous API and a polymer in an SDD, giving insights into molecular association and understanding of the role of the polymer in API stability (such as recrystallization, degradation, etc.) in such novel composite drug products.

  2. A TIPS-TPDO-tetraCN-Based n-Type Organic Field-Effect Transistor with a Cross-linked PMMA Polymer Gate Dielectric.

    Science.gov (United States)

    Jung, Sungyeop; Albariqi, Mohammed; Gruntz, Guillaume; Al-Hathal, Thamer; Peinado, Alba; Garcia-Caurel, Enric; Nicolas, Yohann; Toupance, Thierry; Bonnassieux, Yvan; Horowitz, Gilles

    2016-06-15

    Recent improvement in the performance of the n-type organic semiconductors as well as thin gate dielectrics based on cross-linked polymers offers new opportunities to develop high-performance low-voltage n-type OFETs suitable for organic complementary circuits. Using TIPS-tetracyanotriphenodioxazine (TIPS-TPDO-tetraCN) and cross-linked poly(methyl methacrylate) (c-PMMA), respectively as n-type organic semiconductor and gate dielectric, linear regime field-effect mobility (1.8 ± 0.2) × 10(-2) cm(2) V(-1)s(-1), small spatial standard deviation of threshold voltage (∼0.1 V), and operating voltage less than 3 V are attainable with the same device structure and contact materials used commonly for p-type OFETs. Through comparative static and dynamic characterizations of c-PMMA and PMMA gate dielectrics, it is shown that both smaller thickness and larger relative permittivity of c-PMMA contributes to reduced operating voltage. Furthermore, negligible hysteresis brings evidence to small trap states in the semiconductor near gate dielectric of the n-type OFETs with c-PMMA. The use of TIPS-TPDO-tetraCN and c-PMMA is fully compatible with polyethylene terephthalate substrate, giving promise to various flexible applications.

  3. Ultrasensitive Multi-Functional Flexible Sensors Based on Organic Field-Effect Transistors with Polymer-Dispersed Liquid Crystal Sensing Layers.

    Science.gov (United States)

    Song, Myeonghun; Seo, Jooyeok; Kim, Hwajeong; Kim, Youngkyoo

    2017-06-01

    Ultrasensitive flexible sensors with multi-sensing functions are required for various applications in flexible electronics era. Here we demonstrate flexible polymer-dispersed liquid crystal (PDLC)-integrated-organic field-effect transistors (OFETs) (PDLC-i-OFETs), which sensitively respond to various stimulations including weak gas (air) flow, direct physical touch, light, and heat. The flexible PDLC-i-OFETs were fabricated by spin-coating the poly(methyl methacrylate) (PMMA)-dispersed 4,4'-pentyl-cyanobiphenyl (5CB) layers on the poly(3-hexylthiophene) (P3HT) channel layers of OFETs with 200 μm-thick poly(ethylene naphthalate) (PEN) substrates. The flexible PDLC-i-OFET devices could sense very weak nitrogen gas flow (0.3 sccm), which cannot be felt by human skins, and stably responded to direct physical touches (0.6~4.8 g load). In addition, the present devices showed very sensitive photoresponses to a visible light and exhibited excellent heat-sensing characteristics at a temperature of 25~70 °C. In particular, the present flexible PDLC-i-OFET devices could sense two different stimulations at the same time, indicative of promising multi-sensing capabilities.

  4. Micromechanics of Amorphous Metal/Polymer Hybrid Structures with 3D Cellular Architectures: Size Effects, Buckling Behavior, and Energy Absorption Capability.

    Science.gov (United States)

    Mieszala, Maxime; Hasegawa, Madoka; Guillonneau, Gaylord; Bauer, Jens; Raghavan, Rejin; Frantz, Cédric; Kraft, Oliver; Mischler, Stefano; Michler, Johann; Philippe, Laetitia

    2017-02-01

    By designing advantageous cellular geometries and combining the material size effects at the nanometer scale, lightweight hybrid microarchitectured materials with tailored structural properties are achieved. Prior studies reported the mechanical properties of high strength cellular ceramic composites, obtained by atomic layer deposition. However, few studies have examined the properties of similar structures with metal coatings. To determine the mechanical performance of polymer cellular structures reinforced with a metal coating, 3D laser lithography and electroless deposition of an amorphous layer of nickel-boron (NiB) is used for the first time to produce metal/polymer hybrid structures. In this work, the mechanical response of microarchitectured structures is investigated with an emphasis on the effects of the architecture and the amorphous NiB thickness on their deformation mechanisms and energy absorption capability. Microcompression experiments show an enhancement of the mechanical properties with the NiB thickness, suggesting that the deformation mechanism and the buckling behavior are controlled by the brittle-to-ductile transition in the NiB layer. In addition, the energy absorption properties demonstrate the possibility of tuning the energy absorption efficiency with adequate designs. These findings suggest that microarchitectured metal/polymer hybrid structures are effective in producing materials with unique property combinations. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Semiconductive behavior of and the fabrication of ap-n junction diode from amorphous polymer-derived ceramics

    Science.gov (United States)

    Ryu, Hee-Yeon

    The electrical properties of high temperature semiconducting silicon oxycarbonitride (SiCNO) using titanium nitride (TiN) interconnects are studied. This research had three objectives. The first was to fabricate possible high temperature electrical ceramic and to construct metallic interconnects on SiCNO. The interconnect was selected by investigating the reaction between metals and SiCNO in powders by x-ray characterization of the reaction products. It was concluded that TiN is the most suitable interconnect material. In the final process TiN was produced by coating SiCNO with Ti by RF magnetron sputtering and then heat-treating at high temperatures in argon or nitrogen atmosphere to form TiN. The phase transformation from Ti to TIN starts at 1000°C, however optimum condition for the formation of TiN layer was found to be 1200°C for 2 hours. X-ray analysis on the coated and heat-treated surface reveals presence of TiN and TiO2 phases. The TiN coating was found to be stable up to a maximum temperature of about 1400°C without any noticeable degradation, which was confirmed X-ray analysis. The second was to study the electrical properties of silicon oxycarbonitride (SiCNO) at temperature up to 1300°C as a function of their composition. Silicon oxycarbonitride was made with processing temperature between 1100°C and 1400°C. Their electrical conductivities at temperature up to 1300°C were measured as a function of their chemical compositions that were already analyzed for each processing conditions. As varying processing temperature, their chemical compositions were changed and affect their electrical conductivity. The ratio of nitrogen and oxygen in SiCNO affected their electrical conductivity changes. Polymer-derived SiCNO ceramics remained semiconductive at all temperature and followed Mott's variable range hopping (VRH) mechanism for amorphous semiconductor. From the carrier concentration by Hall-effect measurement of SiCNO ceramics, their hopping energy and

  6. New development of large-area direct conversion detector for digital radiography using amorphous selenium with a C60-doped polymer layer

    Science.gov (United States)

    Nariyuki, F.; Imai, S.; Watano, H.; Nabeta, T.; Hosoi, Y.

    2010-04-01

    We have developed a novel direct conversion detector for digital radiography by using a fullerene (C60)-doped polymer layer added on a thick amorphous selenium (a-Se) layer coupled to an amorphous silicon thin-film transistor (a-Si TFT) array. This detector exhibits considerable improvement in the lag characteristics and durability in high ambient temperatures. The C60-doped polymer layer, which is directly and uniformly solution cast on the a-Se layer and followed by an inorganic electron-transporting layer, smoothly changes the electronic junction between the a-Se layer and the inorganic layer. It lubricates the emission of photocurrents from the a-Se photo-conversion layer and leads to the improved lag characteristics. Another merit of using a C60-doped polymer is that it is stabile in high-temperature ambient conditions and is not degraded by humidity or a large amount of X-ray exposure. The polymer layer prevents the crystallization of a-Se, which otherwise occurs on exposure of a-Se to high temperature not only during the deposition of the inorganic layer or the metal electrode layer in the manufacturing process but also in actual use. A prototype detector, with a size of 17 in × 17 in and a pixel pitch of 150 μm, exhibited a good resolution; its DQE is approximately 48% at 1 cy/mm in 258 μC/kg (RQA5). This new development can simplify cooling apparatus and detector modules and also make a wide range of operational environments available. In addition, the improved lag characteristics make it possible to reduce the exposure intervals for static imaging, tomosynthesis, and other various exposure techniques.

  7. Binding affinity of a small molecule to an amorphous polymer in a solvent. Part 1: free energy of binding to a binding site.

    Science.gov (United States)

    Chunsrivirot, Surasak; Diao, Ying; Trout, Bernhardt L

    2011-10-18

    Crystallization is commonly used in a separation and purification process in the production of a wide range of materials in various industries. In industry, crystallization usually starts with heterogeneous nucleation on a foreign surface. The complicated mechanism of heterogeneous nucleation is not well understood; however, we hypothesize that there might be a possible correlation between binding affinity to a surface and enhancement of nucleation. Recent studies show that amorphous polymers can be used to control crystallization, selectively produce pharmaceutical polymorphs, and discover novel pharmaceutical polymorphs. To investigate the possible correlation between the binding affinity of one molecule to key binding sites (local binding) and heterogeneous nucleation activity as well as the possibility of using this binding affinity to help guide the selection of polymers that promote heterogeneous nucleation, we computed the free energy of binding of aspirin to four nonporous cross-linked polymers in an ethanol-water 38 v% mixture. These cross-linked polymers are poly(4-acryloylmorpholine) (PAM), poly(2-carboxyethyl acrylate) (PCEA), poly(4-hydroxylbutyl acrylate) (PHBA), and polystyrene (PS); all of them were cross-linked with divinylbenzene (DVB). These systems were used because their heterogeneous nucleation activities are available in literature, and the ranking is PAM > PCEA > PHBA ≈ PS. We generated three independent surfaces for each polymer and computed the free energy of binding of aspirin to the best binding site that we found on each surface. The average free energies of binding to the best sites of PAM, PCEA, PHBA, and PS are -20.4 ± 1.0, -16.7 ± 1.0, -14.4 ± 1.1, and -13.6 ± 1.1 kcal/mol, respectively. We found that the trend of the magnitudes of the average free energies of binding to the best sites is PAM > PCEA > PHBA ≈ PS. This trend is very similar to that of heterogeneous nucleation activity. Our results suggest the importance of the

  8. Four-year polymer biocompatibility and vascular healing profile of a novel ultrahigh molecular weight amorphous PLLA bioresorbable vascular scaffold: an OCT study in healthy porcine coronary arteries.

    Science.gov (United States)

    Vahl, Torsten P; Gasior, Pawel; Gongora, Carlos A; Ramzipoor, Kamal; Lee, Chang; Cheng, Yanping; McGregor, Jenn; Shibuya, Masahiko; Estrada, Edward A; Conditt, Gerard B; Kaluza, Greg L; Granada, Juan F

    2016-12-20

    The vascular healing profile of polymers used in bioresorbable vascular scaffolds (BRS) has not been fully characterised in the absence of antiproliferative drugs. In this study, we aimed to compare the polymer biocompatibility profile and vascular healing response of a novel ultrahigh molecular weight amorphous PLLA BRS (FORTITUDE®; Amaranth Medical, Mountain View, CA, USA) against bare metal stent (BMS) controls in porcine coronary arteries. Following device implantation, optical coherence tomography (OCT) evaluation was performed at 0 and 28 days, and at one, two, three and four years. A second group of animals underwent histomorphometric evaluation at 28 and 90 days. At four years, both lumen (BRS 13.19±1.50 mm2 vs. BMS 7.69±2.41 mm2) and scaffold areas (BRS 15.62±1.95 mm2 vs. BMS 8.65±2.37 mm2) were significantly greater for BRS than BMS controls. The degree of neointimal proliferation was comparable between groups. Histology up to 90 days showed comparable healing and inflammation profiles for both devices. At four years, the novel PLLA BRS elicited a vascular healing response comparable to BMS in healthy pigs. Expansive vascular remodelling was evident only in the BRS group, a biological phenomenon that appears to be independent of the presence of antiproliferative drugs.

  9. The origin of excellent gate-bias stress stability in organic field-effect transistors employing fluorinated-polymer gate dielectrics.

    Science.gov (United States)

    Kim, Jiye; Jang, Jaeyoung; Kim, Kyunghun; Kim, Haekyoung; Kim, Se Hyun; Park, Chan Eon

    2014-11-12

    Tuning of the energetic barriers to charge transfer at the semiconductor/dielectric interface in organic field-effect transistors (OFETs) is achieved by varying the dielectric functionality. Based on this, the correlation between the magnitude of the energy barrier and the gate-bias stress stability of the OFETs is demonstrated, and the origin of the excellent device stability of OFETs employing fluorinated dielectrics is revealed. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. The relevance of molecular weight in the design of amorphous biodegradable polymers with optimized shape memory effect.

    Science.gov (United States)

    Petisco-Ferrero, S; Fernández, J; Fernández San Martín, M M; Santamaría Ibarburu, P A; Sarasua Oiz, J R

    2016-08-01

    The shape memory effect (SME) has long been the focus of interest of many research groups that have studied many facets of it, yet to the authors' knowledge some molecular parameters, such as the molecular weight, have been skipped. Thus, the aim of this work is to offer further insight into the shape memory effect, by disclosing the importance of the molecular weight as the relevant parameter dictating the extension of the rubbery plateau, which is the scenario where the entropic network of entanglements manifests. For this, a set of biodegradable amorphous poly(rac-d,l)lactides have been synthesised by ring opening copolymerization of a racemic mixture of L-and D-lactide. The analysis performed on the synthesised enantiomeric copolylactides includes the determination of molecular weights by means of Gel Permeation Chromatography (GPC), thermal properties by Differential Scanning Calorimetry (DSC), dynamic mechanical analysis (DMA) and rheological tests using small amplitude oscillatory flow analysis. Shape memory properties have been determined by means of specific cyclic thermo-mechanic test protocol. It has been shown that the recovery capacity of amorphous PDLLA is linked to the disentanglement time through an exponential law. Copyright © 2016 Elsevier Ltd. All rights reserved.

  11. Mechanical properties of melt-processed polymer blend of amorphous corn flour composite filler and styrene-butadiene rubber

    Science.gov (United States)

    The corn flour composite fillers were prepared by blending corn flour with rubber latex, dried, and cryogenically ground into powders, which were then melt-blended with rubber polymers in an internal mixer to form composites with enhanced mechanical properties. The composites prepared with melt-blen...

  12. Functionalized methanofullerenes used as n-type materials in bulk-heterojunction polymer solar cells and in field-effect transistors.

    Science.gov (United States)

    Yang, Changduk; Kim, Jin Young; Cho, Shinuk; Lee, Jae Kwan; Heeger, Alan J; Wudl, Fred

    2008-05-21

    The synthesis of two well-solubilized [60]methanofullerene derivatives ( p- EHO-PCBM and p- EHO-PCBA) is presented for usage in organic solar cells and in field-effect transistors. The para position of the PCBM's phenyl ring was substituted with a branched alkoxy side chain, which contributes to higher solubility, facilitating synthesis, purification, and processing. We find a small change of the open-circuit voltage ( V oc) as a slight improvement in performance upon application in P3HT/[60]methanofullerene bulk-heterojunction-photovoltaic cells, when compared to PCBM, because of the electron donation of the alkoxy group. In the case of the devices with a TiO x layer, the best power conversion efficiencies (PCE, eta e) is observed in a layered structure of P3HT/ p- EHO-PCBA/TiO x (eta e = 2.6%), which slightly exceeds that of P3HT/PCBM/TiO x (eta e = 2.3%) under conditions reported here. This can be attributed, in part, to the carboxylic acid group in p- EHO-PCBA that leads to an effective interface interaction between the active layer and TiO x phase. In addition, n-channel organic field-effect transistor (OFET) devices were fabricated with thin films of p- EHO-PCBM and p- EHO-PCBA, respectively cast from solution on SiO 2/Si substrates. The values of field-effect mobility (mu) for p- EHO-PCBM and p- EHO-PCBA are 1 x 10 (-2) and 1.6 x 10 (-3) cm (2)/V.s, respectively. The results in this paper demonstrate the effects of a carboxylic acid group and an electron-donating substituent in [60]methanofullerenes as n-type materials with respect to organic solar cells and OFET applications.

  13. Enhanced efficiency of hybrid amorphous silicon solar cells based on single-walled carbon nanotubes and polymer composite thin film

    Science.gov (United States)

    Rajanna, Pramod M.; Gilshteyn, Evgenia P.; Yagafarov, Timur; Aleekseeva, Alena K.; Anisimov, Anton S.; Neumüller, Alex; Sergeev, Oleg; Bereznev, Sergei; Maricheva, Jelena; Nasibulin, Albert G.

    2018-03-01

    We report a simple approach to fabricate hybrid solar cells (HSCs) based on a single-walled carbon nanotube (SWCNT) film and thin film hydrogenated amorphous silicon (a-Si:H). Randomly oriented high-quality SWCNTs with conductivity enhanced by means of poly(3,4-ethylenedioxythiophene) polystyrene sulfonate are used as a window layer and a front electrode. A series of HSCs are fabricated in ambient conditions with varying SWCNT film thicknesses. The polymethylmethacrylate layer drop-casted on fabricated HSCs reduces the reflection fourfold and enhances the short-circuit J sc , open-circuit V oc , and efficiency by nearly 10%. A state-of-the-art J-V performance is shown for SWCNT/a-Si HSC with an open-circuit voltage of 900 mV and an efficiency of 3.4% under simulated one-sun AM 1.5 G direct illumination.

  14. Modélisation et simulation 3D de la rupture des polymères amorphes

    OpenAIRE

    Guo , Shu

    2013-01-01

    We investigate 3D effect of crack tip palsticity and the influence of the thickness on 3D glassy polymer fracture. The characteristuc constitutive law with a viscoplastic yield stress followed by softening and progressive hardening is accoutne for and implemented in a UMAt routine, in abaqus. The crack tip fields are investigated and 2D plasne strain versus 3D calculations compared. Qualitatively, the palstic distribution are comparableas soon as the ratio thickness over crack tip radius is l...

  15. Efficient charge injection in p-type polymer field-effect transistors with low-cost molybdenum electrodes through V2O5 interlayer.

    Science.gov (United States)

    Baeg, Kang-Jun; Bae, Gwang-Tae; Noh, Yong-Young

    2013-06-26

    Here we report high-performance polymer OFETs with a low-cost Mo source/drain electrode by efficient charge injection through the formation of a thermally deposited V2O5 thin film interlayer. A thermally deposited V2O5 interlayer is formed between a regioregular poly(3-hexylthiophene) (rr-P3HT) or a p-type polymer semiconductor containing dodecyl-substituted thienylenevinylene (TV) and dodecylthiophene (PC12TV12T) and the Mo source/drain electrode. The P3HT or PC12TV12T OFETs with the bare Mo electrode exhibited lower charge carrier mobility than those with Au owing to a large barrier height for hole injection (0.5-1.0 eV). By forming the V2O5 layer, the P3HT or PC12TV12T OFETs with V2O5 on the Mo electrode exhibited charge carrier mobility comparable to that of a pristine Au electrode. Best P3HT or PC12TV12T OFETs with 5 nm thick V2O5 on Mo electrode show the charge carrier mobility of 0.12 and 0.38 cm(2)/(V s), respectively. Ultraviolet photoelectron spectroscopy results exhibited the work-function of the Mo electrode progressively changed from 4.3 to 4.9 eV with an increase in V2O5 thickness from 0 to 5 nm, respectively. Interestingly, the V2O5-deposited Mo exhibits comparable Rc to Au, which mainly results from the decreased barrier height for hole carrier injection from the low-cost metal electrode to the frontier molecular orbital of the p-type polymer semiconductor after the incorporation of the transition metal oxide hole injection layer, such as V2O5. This enables the development of large-area, low-cost electronics with the Mo electrodes and V2O5 interlayer.

  16. Pronounced Side Chain Effects in Triple Bond-Conjugated Polymers Containing Naphthalene Diimides for n-Channel Organic Field-Effect Transistors

    KAUST Repository

    Nam, Sungho

    2018-03-23

    Three triple bond-conjugated naphthalene diimide (NDI) copolymers, poly{[N,N′-bis(2-R1)-naphthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl]-alt-[(2,5-bis(2-R2)-1,4-phenylene)bis(ethyn-2,1-diyl)]} (PNDIR1-R2), were synthesized via Sonogashira coupling polymerization with varying alkyl side chains at the nitrogen atoms of the imide ring and 2,5-positions of the 1,4-diethynylbenzene moiety. Considering their identical polymer backbone structures, the side chains were found to have a strong influence on the surface morphology/nanostructure, thus playing a critical role in charge-transporting properties of the three NDI-based copolymers. Among the polymers, the one with an octyldodecyl (OD) chain at the nitrogen atoms of imide ring and a hexadecyloxy (HO) chain at the 2,5-positions of 1,4-diethynylbenzene, P(NDIOD-HO), exhibited the highest electron mobility of 0.016 cm2 V–1 s–1, as compared to NDI-based copolymers with an ethylhexyl chain at the 2,5-positions of 1,4-diethynylbenzene. The enhanced charge mobility in the P(NDIOD-HO) layers is attributed to the well-aligned nano-fiber-like surface morphology and highly ordered packing structure with a dominant edge-on orientation, thus enabling efficient in-plane charge transport. Our results on the molecular structure–charge transport property relationship in these materials may provide an insight into novel design of n-type conjugated polymers for applications in the organic electronics of the future.

  17. Ultra-Flexible, Invisible Thin-Film Transistors Enabled by Amorphous Metal Oxide/Polymer Channel Layer Blends

    Science.gov (United States)

    2015-02-25

    200 nm thick amor - phous Zn 0.3 In 1.4 Sn 0.3 O 3 (a-ZITO) fi lm was deposited on Ary- lite by pulsed laser deposition (PLD) to function as the gate...level. Thus, appropriate polymer incorporation promotes the amor - phous state but allows a suffi cient density of connected InO x polyhedra for effi...continuous and uniform. In conclusion, we have successfully developed a new low temperature route (as low as 225 °C) to high-mobility amor - phous metal

  18. Improvement of a block co-polymer (PS-b-PDMS) template etch profile using amorphous carbon layer

    Science.gov (United States)

    Oh, JiSoo; Oh, Jong Sik; Sung, DaIn; Yim, SoonMin; Song, SeungWon; Yeom, GeunYoung

    2017-03-01

    Block copolymers (BCPs) are consisted of at least two types of monomers which have covalent bonding. One of the widely investigated BCPs is polystyrene-block-polydimethylsiloxane (PS-b-PDMS), which is used as an alternative patterning method for various deep nanoscale devices due to its high Flory-Huggins interaction parameter (χ), such as optical devices and transistors, replacing conventional photolithography. As an alternate or supplementary nextgeneration lithography technology to extreme ultraviolet lithography (EUVL), BCP lithography utilizing the DSA of BCP has been actively studied. However, the nanoscale BCP mask material is easily damaged by the plasma and has a very low etch selectivity over bottom semiconductor materials, because it is composed of polymeric materials even though it contains Si in PDMS. In this study, an amorphous carbon layer (ACL) was inserted as a hardmask material between BCP and materials to be patterned, and, by using O2 plasmas, the characteristics of dry etching of ACL for high aspect ratio (HAR) using a 10 nm PDMS pattern were investigated. The results showed that, by using a PS-b-PDMS pattern with an aspect ratio of 0.3 0.9:1, a HAR PDMS/ACL double layer mask with an aspect ratio of 10:1 could be fabricated. In addition, by the optimization of the plasma etch process, ACL masks with excellent sidewall roughness (SWR,1.35 nm) and sidewall angle (SWA, 87.9˚) could be fabricated.

  19. Surface modification of aluminum nitride by polysilazane and its polymer-derived amorphous silicon oxycarbide ceramic for the enhancement of thermal conductivity in silicone rubber composite

    Science.gov (United States)

    Chiu, Hsien Tang; Sukachonmakul, Tanapon; Kuo, Ming Tai; Wang, Yu Hsiang; Wattanakul, Karnthidaporn

    2014-02-01

    Polysilazane (PSZ) and its polymer-derived amorphous silicon oxycarbide (SiOC) ceramic were coated on aluminum nitride (AlN) by using a dip-coating method to allow moisture-crosslinking of PSZ on AlN, followed by heat treatment at 700 °C in air to convert PSZ into SiOC on AlN. The results from FTIR, XPS and SEM indicated that the surface of AlN was successfully coated by PSZ and SiOC film. It was found that the introduction of PSZ and SiOC film help improve in the interfacial adhesion between the modified AlN (PSZ/AlN and SiOC/AlN) and silicone rubber lead to the increase in the thermal conductivity of the composites since the thermal boundary resistance at the filler-matrix interface was decreased. However, the introduction of SiOC as an intermediate layer between AlN and silicone rubber could help increase the thermal energy transport at the filler-matrix interface rather than using PSZ. This result was due to the decrease in the surface roughness and thickness of SiOC film after heat treatment at 700 °C in air. Thus, in the present work, a SiOC ceramic coating could provide a new surface modification for the improvement of the interfacial adhesion between the thermally conductive filler and the matrix in which can enhance the thermal conductivity of the composites.

  20. High-Throughput Image Analysis of Fibrillar Materials: A Case Study on Polymer Nanofiber Packing, Alignment, and Defects in Organic Field Effect Transistors.

    Science.gov (United States)

    Persson, Nils E; Rafshoon, Joshua; Naghshpour, Kaylie; Fast, Tony; Chu, Ping-Hsun; McBride, Michael; Risteen, Bailey; Grover, Martha; Reichmanis, Elsa

    2017-10-18

    High-throughput discovery of process-structure-property relationships in materials through an informatics-enabled empirical approach is an increasingly utilized technique in materials research due to the rapidly expanding availability of data. Here, process-structure-property relationships are extracted for the nucleation, growth, and deposition of semiconducting poly(3-hexylthiophene) (P3HT) nanofibers used in organic field effect transistors, via high-throughput image analysis. This study is performed using an automated image analysis pipeline combining existing open-source software and new algorithms, enabling the rapid evaluation of structural metrics for images of fibrillar materials, including local orientational order, fiber length density, and fiber length distributions. We observe that microfluidic processing leads to fibers that pack with unusually high density, while sonication yields fibers that pack sparsely with low alignment. This is attributed to differences in their crystallization mechanisms. P3HT nanofiber packing during thin film deposition exhibits behavior suggesting that fibers are confined to packing in two-dimensional layers. We find that fiber alignment, a feature correlated with charge carrier mobility, is driven by increasing fiber length, and that shorter fibers tend to segregate to the buried dielectric interface during deposition, creating potentially performance-limiting defects in alignment. Another barrier to perfect alignment is the curvature of P3HT fibers; we propose a mechanistic simulation of fiber growth that reconciles both this curvature and the log-normal distribution of fiber lengths inherent to the fiber populations under consideration.

  1. Application of X-ray microtomography for the characterisation of hollow polymer-stabilised spray dried amorphous dispersion particles.

    Science.gov (United States)

    Gamble, John F; Terada, Masako; Holzner, Christian; Lavery, Leah; Nicholson, Sarah J; Timmins, Peter; Tobyn, Mike

    2016-08-20

    The aim of this study was to investigate the capability of X-ray microtomography to obtain information relating to powder characteristics such as wall thickness and solid volume fraction for hollow, polymer-stabilised spray dried dispersion (SDD) particles. SDDs of varying particle properties, with respect to shell wall thickness and degree of particle collapse, were utilised to assess the capability of the approach. The results demonstrate that the approach can provide insight into the morphological characteristics of these hollow particles, and thereby a means to understand/predict the processability and performance characteristics of the bulk material. Quantitative assessments of particle wall thickness, particle/void volume and thereby solid volume fraction were also demonstrated to be achievable. The analysis was also shown to be able to qualitatively assess the impact of the drying rate on the morphological nature of the particle surfaces, thus providing further insight into the final particle shape. The approach demonstrated a practical means to access potentially important particle characteristics for SDD materials which, in addition to the standard bulk powder measurements such as particle size and bulk density, may enable a better understanding of such materials, and their impact on downstream processability and dosage form performance. Crown Copyright © 2016. Published by Elsevier B.V. All rights reserved.

  2. Amorphous magnetism

    International Nuclear Information System (INIS)

    Rechenberg, H.R.

    1984-01-01

    The consequences of disorder on magnetic properties of solids are examined. In this context the word 'disorder' is not synonimous of structural amorphicity; chemical disorder can be achieved e.g. by randomly diffusing magnetic atoms on a nonmagnetic crystalline lattice. The name Amorphous Magnetism must be taken in a broad sense. (Author) [pt

  3. Emerging trends in the stabilization of amorphous drugs

    DEFF Research Database (Denmark)

    Laitinen, Riikka; Löbmann, Korbinian; Strachan, Clare J.

    2013-01-01

    water-soluble drugs can be increased by the formation of stabilized amorphous forms. Currently, formulation as solid polymer dispersions is the preferred method to enhance drug dissolution and to stabilize the amorphous form of a drug. The purpose of this review is to highlight emerging alternative...... methods to amorphous polymer dispersions for stabilizing the amorphous form of drugs. First, an overview of the properties and stabilization mechanisms of amorphous forms is provided. Subsequently, formulation approaches such as the preparation of co-amorphous small-molecule mixtures and the use...

  4. Amorphous nanophotonics

    CERN Document Server

    Scharf, Toralf

    2013-01-01

    This book represents the first comprehensive overview over amorphous nano-optical and nano-photonic systems. Nanophotonics is a burgeoning branch of optics that enables many applications by steering the mould of light on length scales smaller than the wavelength with devoted nanostructures. Amorphous nanophotonics exploits self-organization mechanisms based on bottom-up approaches to fabricate nanooptical systems. The resulting structures presented in the book are characterized by a deterministic unit cell with tailored geometries; but their spatial arrangement is not controlled. Instead of periodic, the structures appear either amorphous or random. The aim of this book is to discuss all aspects related to observable effects in amorphous nanophotonic material and aspects related to their design, fabrication, characterization and integration into applications. The book has an interdisciplinary nature with contributions from scientists in physics, chemistry and materials sciences and sheds light on the topic fr...

  5. Polymer electronics

    CERN Document Server

    Hsin-Fei, Meng

    2013-01-01

    Polymer semiconductor is the only semiconductor that can be processed in solution. Electronics made by these flexible materials have many advantages such as large-area solution process, low cost, and high performance. Researchers and companies are increasingly dedicating time and money in polymer electronics. This book focuses on the fundamental materials and device physics of polymer electronics. It describes polymer light-emitting diodes, polymer field-effect transistors, organic vertical transistors, polymer solar cells, and many applications based on polymer electronics. The book also disc

  6. Emerging trends in the stabilization of amorphous drugs.

    Science.gov (United States)

    Laitinen, Riikka; Löbmann, Korbinian; Strachan, Clare J; Grohganz, Holger; Rades, Thomas

    2013-08-30

    The number of active pharmaceutical substances having high therapeutic potential but low water solubility is constantly increasing, making it difficult to formulate these compounds as oral dosage forms. The solubility and dissolution rate, and thus potentially the bioavailability, of these poorly water-soluble drugs can be increased by the formation of stabilized amorphous forms. Currently, formulation as solid polymer dispersions is the preferred method to enhance drug dissolution and to stabilize the amorphous form of a drug. The purpose of this review is to highlight emerging alternative methods to amorphous polymer dispersions for stabilizing the amorphous form of drugs. First, an overview of the properties and stabilization mechanisms of amorphous forms is provided. Subsequently, formulation approaches such as the preparation of co-amorphous small-molecule mixtures and the use of mesoporous silicon and silica-based carriers are presented as potential means to increase the stability of amorphous pharmaceuticals. Copyright © 2012 Elsevier B.V. All rights reserved.

  7. Loi physique de comportement des polymères amorphes et intégration dans un code éléments finis

    OpenAIRE

    Rinaldi , Renaud

    2006-01-01

    A set of physical based constitutive equations is developped for amorphous polymeric materials based on molecular mobility concepts. The proposed model allows a coherent description of the non linear viscoelasto-viscoplastic behavior from small to large strains aera. A set of materials parameters were depicted for the BisphenolA polycarbonate from Lexan. The constitutive equation is implemented in the finite element package abaqus, consisting in the writing of a umat file. The whole mechanica...

  8. Theoretical Considerations in Developing Amorphous Solid Dispersions

    DEFF Research Database (Denmark)

    Laitinen, Riikka; Priemel, Petra Alexandra; Surwase, Sachin

    2014-01-01

    to their glass-forming ability and glass stability. In the main parts of this chapter, we review theoretical approaches to determine amorphous drug polymer miscibility and crystalline drug polymer solubility, as a prerequisite to develop amorphous solid dispersions (glass solutions).......Before pursuing the laborious route of amorphous solid dispersion formulation and development, which is the topic of many of the subsequent chapters in this book, the formulation scientist would benefit from a priori knowledge whether the amorphous route is a viable one for a given drug and how...... much solubility improvement, and hence increase in bioavailability, can be expected, and what forms of solid dispersion have been developed in the past. In this chapter, we therefore initially define the various forms of solid dispersions, and then go on to discuss properties of pure drugs with respect...

  9. Spectroscopic and calorimetric investigation of short and intermediate-range structures and energetics of amorphous SiCO, SiCN, and SiBCN polymer-derived ceramics

    Science.gov (United States)

    Widgeon, Scarlett J.

    Polymer-derived ceramics (PDCs) are a new class of amorphous ceramics in the Si-B-C-N system that are synthesized by the pyrolysis of silicon-based organic polymers. PDCs are lightweight and are resistant to creep, crystallization, and oxidation at temperatures near 1800 K making them ideal for a variety of high temperature applications. In spite of being X-ray amorphous, these materials display structural heterogeneity at the nanometer length scale. Their structure and resulting properties can be drastically altered by the utilization of preceramic polymers with differing chemistry and architectures. Fundamental understanding of the atomic structure is critical in deciphering the structure-property relationships and ultimately in controlling their properties for specific engineering applications. The short-range atomic structure has been extensively investigated using a variety of techniques, however, the structures at length scales beyond next-nearest neighbors remained highly controversial. Here we report the results of a spectroscopic and calorimetric study of short and intermediate -range structure and energetic of SiOC and SiBCN PDCs derived from a wide variety of precursors. SiOC PDCs with different carbon contents were synthesized from polysiloxane precurors and their structures were studied using high-resolution 13C and 29Si nuclear magnetic resonance (NMR) spectroscopy. The results suggest that these PDCs consists of a continuous mass fractal backbone of corner-shared SiC xO4-x tetrahedral units with "voids" occupied by sp 2-hybridized graphitic carbon. The oxygen-rich SiCxO 4-x units are located at the interior of this backbone with a mass fractal dimension of ~ 2.5, while the carbon-rich units occupy the two-dimensional interface between the backbone and the free carbon nanodomains. Such fractal topology is expected to give rise to unusual mechanical and transport properties characteristic of fractal percolation networks. For example, elastic moduli and

  10. New copolythiophene containing thiophene integrated in the polymer chain, useful in the form of a field effect transistor, a diode, a photovoltaic cell, an integrated circuit, a capacitor or a sensor

    OpenAIRE

    Janietz, Silvia; Krueger, Hartmut; Egorov-Brening, Tatjana

    2011-01-01

    Copolythiophene containing thiophene (I) integrated in the polymer chain, is new. Copolythiophene containing thiophene of formula (I) integrated in the polymer chain, is new. R 1>an oxygen moiety of formula [(-CH 2) n-O] m-R 2>; R 2>1-18C alkyl; n : 1-6; and m : 1-20, preferably 1-9. An independent claim is also included for the electrical component comprising a semiconductor made from a copolythiophene.

  11. Effect of micro-environment modification and polymer type on the in-vitro dissolution behavior and in-vivo performance of amorphous solid dispersions.

    Science.gov (United States)

    Sun, Weiwei; Pan, Baoliang

    2017-06-15

    This study investigates the effects of micro-environment modification and polymer type on the in-vitro dissolution behavior and in-vivo performance of micro-environment pH modifying solid dispersions (pH M -SD) for the poorly water-soluble model drug Toltrazuril (TOL). Various pH M -SDs were prepared using Ca(OH) 2 as a pH-modifier in hydrophilic polymers, including polyethylene glycol 6000 (PEG6000), polyvinylpyrrolidone k30 (PVPk30) and hydroxypropyl methylcellulose (HPMC). Based on the results of physicochemical characterizations and in-vitro dissolution testing, the representative ternary (Ca(OH) 2 :TOL:PEG6000/HPMC/PVPk30=1:8:24, w/w/w) and binary (TOL:PVPk30=1:3, w/w) solid dispersions were selected and optimized to perform in-vivo pharmacokinetic study. The micro-environment pH modification improved the in-vitro water-solubility and in-vivo bioavailability of parent drug TOL. Furthermore, the addition of alkalizers not only enhanced the release and absorption of prototype drug, but also promoted the generation of active metabolites, including toltrazuril sulfoxide (TOLSO) and toltrazuril sulfone (TOLSO 2 ). The in-vitro dissolution profiles and in-vivo absorption, distribution and metabolism behaviors of the pH M -SDs varied with polymer type. Moreover, in-vivo bioavailability of three active pharmaceutical ingredients increased with an increase in in-vitro dissolution rates of the drug from the pH M -SDs prepared with various polymers. Therefore, a non-sink in-vitro dissolution method can be used to predict the in-vivo performance of pH M -SDs formulated with various polymers with trend consistency. In-vitro and in-vivo screening procedures revealed that the pH M -SD composed of Ca(OH) 2 , TOL and PVPk30 at a weight ratio of 1:8:24, of which the safety was adequately proved via histopathological examination, may be a promising candidate for providing better clinical outcomes. Copyright © 2017. Published by Elsevier B.V.

  12. Centro-Apical Self-Organization of Organic Semiconductors in a Line-Printed Organic Semiconductor: Polymer Blend for One-Step Printing Fabrication of Organic Field-Effect Transistors

    Science.gov (United States)

    Jin Lee, Su; Kim, Yong-Jae; Young Yeo, So; Lee, Eunji; Sun Lim, Ho; Kim, Min; Song, Yong-Won; Cho, Jinhan; Ah Lim, Jung

    2015-09-01

    Here we report the first demonstration for centro-apical self-organization of organic semiconductors in a line-printed organic semiconductor: polymer blend. Key feature of this work is that organic semiconductor molecules were vertically segregated on top of the polymer phase and simultaneously crystallized at the center of the printed line pattern after solvent evaporation without an additive process. The thickness and width of the centro-apically segregated organic semiconductor crystalline stripe in the printed blend pattern were controlled by varying the relative content of the organic semiconductors, printing speed, and solution concentrations. The centro-apical self-organization of organic semiconductor molecules in a printed polymer blend may be attributed to the combination of an energetically favorable vertical phase-separation and hydrodynamic fluids inside the droplet during solvent evaporation. Finally, a centro-apically phase-separated bilayer structure of organic semiconductor: polymer blend was successfully demonstrated as a facile method to form the semiconductor and dielectric layer for OFETs in one- step.

  13. Centro-Apical Self-Organization of Organic Semiconductors in a Line-Printed Organic Semiconductor: Polymer Blend for One-Step Printing Fabrication of Organic Field-Effect Transistors.

    Science.gov (United States)

    Lee, Su Jin; Kim, Yong-Jae; Yeo, So Young; Lee, Eunji; Lim, Ho Sun; Kim, Min; Song, Yong-Won; Cho, Jinhan; Lim, Jung Ah

    2015-09-11

    Here we report the first demonstration for centro-apical self-organization of organic semiconductors in a line-printed organic semiconductor: polymer blend. Key feature of this work is that organic semiconductor molecules were vertically segregated on top of the polymer phase and simultaneously crystallized at the center of the printed line pattern after solvent evaporation without an additive process. The thickness and width of the centro-apically segregated organic semiconductor crystalline stripe in the printed blend pattern were controlled by varying the relative content of the organic semiconductors, printing speed, and solution concentrations. The centro-apical self-organization of organic semiconductor molecules in a printed polymer blend may be attributed to the combination of an energetically favorable vertical phase-separation and hydrodynamic fluids inside the droplet during solvent evaporation. Finally, a centro-apically phase-separated bilayer structure of organic semiconductor: polymer blend was successfully demonstrated as a facile method to form the semiconductor and dielectric layer for OFETs in one- step.

  14. Amorphous fluorocarbon polymer (a-C:F) films obtained by plasma enhanced chemical vapor deposition from perfluoro-octane (C8F18) vapor I: Deposition, morphology, structural and chemical properties

    International Nuclear Information System (INIS)

    Biloiu, Costel; Biloiu, Ioana Arabela; Sakai, Yosuke; Suda, Yoshiyuki; Ohta, Akitsugu

    2004-01-01

    The method of obtaining amorphous fluorocarbon polymer (a-C:F) films by plasma enhanced chemical vapor deposition in a capacitively coupled, 13.56 MHz reactor, from a new monomer, namely perfluoro-octane (C 8 F 18 ) vapor, is presented. For monomer pressure ranging from 0.2 to 1 Torr and input power density from 0.15 to 0.85 W/cm 3 , the maximum deposition rate reached 300 nm/min, while 10% monomer dilution with argon led to a deposition rate of 200 nm/min. The film surface and bulk morphologies, chemical and structural compositions were investigated using scanning electron microscopy, x-ray photoelectron spectroscopy, and Fourier transform infrared spectroscopy. It was revealed that the films have a dense and compact structure. The fluorine to carbon ratio (F/C) of the films was between 1.57 and 1.75, and the degree of cross-linking was between 55% and 58%. The relative amount of perfluoroalkyl (CF 2 ) groups in the films was 29%. The FTIR spectra showed absorption bands corresponding to the different vibrational modes of CF, CF 2 , and CF 3 moieties

  15. Influence of Carrier (Polymer Type and Drug-Carrier Ratio in the Development of Amorphous Dispersions for Solubility and Permeability Enhancement of Ritonavir

    Directory of Open Access Journals (Sweden)

    Vivek S. Dave

    2017-09-01

    Full Text Available The influence of the ratio of Eudragit® L100-55 or Kolliphor® P188 on the solubility, dissolution, and permeability of ritonavir was studied with a goal of preparing solid dispersions (SDs of ritonavir. SDs were formulated using solvent evaporation or lyophilization techniques, and evaluated for their physical-chemical properties. The dissolution and permeability assessments of the functionality of the SDs were carried out. The preliminary functional stability of these formulations was assessed at accelerated storage conditions for a period of six months. Ritonavir: Eudragit® L100-55 (RE, 1:3 SD showed a 36-fold higher ritonavir solubility compared to pure ritonavir. Similarly, ritonavir: Kolliphor® P188 (RP, 1:2 SD exhibited a 49-fold higher ritonavir solubility compared to pure ritonavir. Ritonavir dissolution from RE formulations increased with increasing ratios of Eudragit® L100-55, up to a ritonavir: carrier ratio of 1:3. The ritonavir dissolution from RP formulations was highest at ritonavir: Kolliphor® P188 ratio of 1:2. Dissolution efficiencies of these formulations were found to be in line with, and supported the dissolution results. The permeability of ritonavir across the biological membrane from the optimized formulations RE (1:3 and RP (1:2 were ~76 % and ~97 %, respectively; and were significantly higher compared to that of pure ritonavir (~20 %. A preliminary (six-month stability study demonstrated the functional stability of prepared solid dispersions. The present study demonstrates that ritonavir solubility, dissolution, and permeability improvement can be achieved with a careful choice of the carrier polymer, and optimizing the amount of polymer in a SD formulation.

  16. Amorphous Carbon: State of the Art - Proceedings of the 1st International Specialist Meeting on Amorphous Carbon (smac '97)

    Science.gov (United States)

    Silva, S. R. P.; Robertson, J.; Milne, W. I.; Amaratunga, G. A. J.

    1998-05-01

    The Table of Contents for the full book PDF is as follows: * Preface * GROWTH AND STRUCTURE * The Structure of Tetrahedral Amorphous Carbon * Growth of DLC Films and Related Structure and Properties * Deposition Mechanism of Diamond-Like Carbon * Relaxation of sp3 Bonds in Hydrogen Free Carbon Films During Growth * MODELLING * Correlations Between Microstructure and Electronic Properties in Amorphous Carbon Based Materials * Review of Monte Carlo Simulations of Diamondlike Amorphous Carbon: Bulk, Surface, and Interface Structural Properties * DEPOSITION * Preparation of Disordered Amorphous and Partially Ordered Nano Clustered Carbon Films by Arc Deposition: A Critical Review * Plasma Deposition of Diamond-Like Carbon in an ECR-RF Discharge * Deposition of Amorphous Hydrogenated Carbon-Nitrogen Films by PECVD Using Several Hydrocarbon / Nitrogen Containing Gas Mixtures * ELECTRONIC STRUCTURE * 'Defects' and Their Detection in a-C and a-C:H * Valence Band and Gap State Spectroscopy of Amorphous Carbon by Photoelectron Emission Techniques * Photoluminescence Spectroscopy: A Probe for Inhomogeneous Structure in Polymer-Like Amorphous Carbon * Raman Characterization of Amorphous and Nanocrystalline sp3 Bonded Structures * Ultraviolet Raman Spectroscopy of Tetrahedral Amorphous Carbon Thin Films * Excitation Energy Dependent Raman and Photoluminescence Spectra of Hydrogenated Amorphous Carbon * MECHANICAL PROPERTIES * Pulsed Laser Deposited a-C: Growth, Structure and Mechanical Properties * Mechanical Properties of Laser-Assisted Deposited Amorphous Carbon Films * Mechanical and Morphology Study on Tetrahedral Amorphous Carbon Films * Time-Dependent Changes in the Mechanical Properties of Diamond-Like Carbon Films * ELECTRONIC PROPERTIES * Electronic Transport in Amorphous Carbon * Electronic Properties of Undoped/Doped Tetrahedral Amorphous Carbon * The Inclusion of Graphitic Nanoparticles in Semiconducting Amorphous Carbon to Enhance Electronic Transport Properties

  17. Short range order in amorphous polycondensates

    Energy Technology Data Exchange (ETDEWEB)

    Lamers, C.; Richter, D.; Schweika, W. [Forschungszentrum Juelich GmbH (Germany). Inst. fuer Festkoerperforschung; Batoulis, J.; Sommer, K. [Bayer AG, Leverkusen (Germany); Cable, J.W. [Oak Ridge National Lab., TN (United States); Shapiro, S.M. [Brookhaven National Lab., Upton, NY (United States)

    1992-12-01

    The static coherent structure factors S(Q) of the polymer glass Bisphenol-A-Polycarbonate and its chemical variation Bisphenol-A- Polyctherkctone- both in differently deuterated versions- have been measured by spin polarized neutron scattering. The method of spin polarization analysis provided an experimental separation of coherent and incoherent scattering and a reliable intensity calibration. Results are compared to structure factors calculated for model structures which were obtained by ``amorphous cell`` computer simulations. In general reasonable agreement is found between experiment and simulation; however, certain discrepancies hint at an insufficient structural relaxation in the amorphous cell method. 15 refs, 1 fig, 1 tab.

  18. Photo-processing P3HT conjugated polymers, in solution: A new route towards ordered polymeric structures.

    Science.gov (United States)

    Barbosa Neto, Newton; Dutra, Marcia; Araujo, Paulo; Sampaio, Renato

    Solution aggregated thin films of conjugated polymers have demonstrated to be promising materials for many applications, e.g., solar cells and field-effect transistors. There are many standard methods to generate aggregates in polymeric solution, which includes poor solvent addiction and solution temperature manipulation. Here, we demonstrate a new approach to induce aggregate formation on solution of P3HT polymer. Under light excitation with 355 nm or 532 nm pulsed laser the polymer exhibit significant changes on its UV-Vis spectrum which are most known in the literature as the formation of H-J aggregates and additional new bands associated with polaron formation. Such changes in the amorphous phase of the polymers are seen in specific conditions of solvent combinations. We show also the dependency on the excitation laser power which can be identified as a threshold to ignite the formation of the new structure. We are grateful to CNPq and CAPES for financial support.

  19. Tunneling field effect transistor technology

    CERN Document Server

    Chan, Mansun

    2016-01-01

    This book provides a single-source reference to the state-of-the art in tunneling field effect transistors (TFETs). Readers will learn the TFETs physics from advanced atomistic simulations, the TFETs fabrication process and the important roles that TFETs will play in enabling integrated circuit designs for power efficiency. · Provides comprehensive reference to tunneling field effect transistors (TFETs); · Covers all aspects of TFETs, from device process to modeling and applications; · Enables design of power-efficient integrated circuits, with low power consumption TFETs.

  20. Organic semiconductors for organic field-effect transistors

    Directory of Open Access Journals (Sweden)

    Yoshiro Yamashita

    2009-01-01

    Full Text Available The advantages of organic field-effect transistors (OFETs, such as low cost, flexibility and large-area fabrication, have recently attracted much attention due to their electronic applications. Practical transistors require high mobility, large on/off ratio, low threshold voltage and high stability. Development of new organic semiconductors is key to achieving these parameters. Recently, organic semiconductors have been synthesized showing comparable mobilities to amorphous-silicon-based FETs. These materials make OFETs more attractive and their applications have been attempted. New organic semiconductors resulting in high-performance FET devices are described here and the relationship between transistor characteristics and chemical structure is discussed.

  1. Amorphous iron (II) carbonate

    DEFF Research Database (Denmark)

    Sel, Ozlem; Radha, A.V.; Dideriksen, Knud

    2012-01-01

    Abstract The synthesis, characterization and crystallization energetics of amorphous iron (II) carbonate (AFC) are reported. AFC may form as a precursor for siderite (FeCO3). The enthalpy of crystallization (DHcrys) of AFC is similar to that of amorphous magnesium carbonate (AMC) and more...

  2. Field Effect Transistor in Nanoscale

    Science.gov (United States)

    2017-04-26

    significant alteration in transport behaviour of these molecular junctions. 15. SUBJECT TERMS Theory , Nanoscale, Field Effect Transistor (FET), Devices...Density Functional Theory (DFT), Non-equilibrium Green Function 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT SAR 18. NUMBER OF PAGES     13...Keep in mind the amount of funding you received relative to the amount of effort you put into the report. References: 1. J. R. Heath and M

  3. Study on the substrate-induced crystallisation of amorphous SiC-precursor ceramics. TIB/A; Untersuchungen zur substratinduzierten Kristallisation amorpher SiC-Precursorkeramiken

    Energy Technology Data Exchange (ETDEWEB)

    Rau, C.

    2000-12-01

    In the present thesis the crystallization behaviour of amorphous silicon-carbon materials (SiC{sub x}) was studied. The main topic of the experimental studies formed thereby the epitactical crystallization of thin silicon carbide layers on monocrystalline substrates of silicon carbides or silicon. Furthermore by thermolysis of the polymer amorphous SiC{sub x}-powder was obtained.

  4. Locomotion of Amorphous Surface Robots

    Science.gov (United States)

    Bradley, Arthur T. (Inventor)

    2016-01-01

    An amorphous robot includes a compartmented bladder containing fluid, a valve assembly, and an outer layer encapsulating the bladder and valve assembly. The valve assembly draws fluid from a compartment(s) and discharges the drawn fluid into a designated compartment to displace the designated compartment with respect to the surface. Another embodiment includes elements each having a variable property, an outer layer that encapsulates the elements, and a control unit. The control unit energizes a designated element to change its variable property, thereby moving the designated element. The elements may be electromagnetic spheres with a variable polarity or shape memory polymers with changing shape and/or size. Yet another embodiment includes an elongated flexible tube filled with ferrofluid, a moveable electromagnet, an actuator, and a control unit. The control unit energizes the electromagnet and moves the electromagnet via the actuator to magnetize the ferrofluid and lengthen the flexible tube.

  5. Hydrogen in amorphous silicon

    International Nuclear Information System (INIS)

    Peercy, P.S.

    1980-01-01

    The structural aspects of amorphous silicon and the role of hydrogen in this structure are reviewed with emphasis on ion implantation studies. In amorphous silicon produced by Si ion implantation of crystalline silicon, the material reconstructs into a metastable amorphous structure which has optical and electrical properties qualitatively similar to the corresponding properties in high-purity evaporated amorphous silicon. Hydrogen studies further indicate that these structures will accomodate less than or equal to 5 at.% hydrogen and this hydrogen is bonded predominantly in a monohydride (SiH 1 ) site. Larger hydrogen concentrations than this can be achieved under certain conditions, but the excess hydrogen may be attributed to defects and voids in the material. Similarly, glow discharge or sputter deposited amorphous silicon has more desirable electrical and optical properties when the material is prepared with low hydrogen concentration and monohydride bonding. Results of structural studies and hydrogen incorporation in amorphous silicon were discussed relative to the different models proposed for amorphous silicon

  6. Physics of amorphous metals

    CERN Document Server

    Kovalenko, Nikolai P; Krey, Uwe

    2008-01-01

    The discovery of bulk metallic glasses has led to a large increase in the industrial importance of amorphous metals, and this is expected to continue. This book is the first to describe the theoretical physics of amorphous metals, including the important theoretical development of the last 20 years.The renowned authors stress the universal aspects in their description of the phonon or magnon low-energy excitations in the amorphous metals, e.g. concerning the remarkable consequences of the properties of these excitations for the thermodynamics at low and intermediate temperatures. Tunneling

  7. Amorphization within the tablet

    DEFF Research Database (Denmark)

    Doreth, Maria; Hussein, Murtadha Abdul; Priemel, Petra A.

    2017-01-01

    , the feasibility of microwave irradiation to prepare amorphous solid dispersions (glass solutions) in situ was investigated. Indomethacin (IND) and polyvinylpyrrolidone K12 (PVP) were tableted at a 1:2 (w/w) ratio. In order to study the influence of moisture content and energy input on the degree of amorphization......, tablet formulations were stored at different relative humidity (32, 43 and 54% RH) and subsequently microwaved using nine different power-time combinations up to a maximum energy input of 90 kJ. XRPD results showed that up to 80% (w/w) of IND could be amorphized within the tablet. mDSC measurements...

  8. Ambipolar phosphorene field effect transistor.

    Science.gov (United States)

    Das, Saptarshi; Demarteau, Marcel; Roelofs, Andreas

    2014-11-25

    In this article, we demonstrate enhanced electron and hole transport in few-layer phosphorene field effect transistors (FETs) using titanium as the source/drain contact electrode and 20 nm SiO2 as the back gate dielectric. The field effect mobility values were extracted to be ∼38 cm(2)/Vs for electrons and ∼172 cm(2)/Vs for the holes. On the basis of our experimental data, we also comprehensively discuss how the contact resistances arising due to the Schottky barriers at the source and the drain end effect the different regime of the device characteristics and ultimately limit the ON state performance. We also propose and implement a novel technique for extracting the transport gap as well as the Schottky barrier height at the metal-phosphorene contact interface from the ambipolar transfer characteristics of the phosphorene FETs. This robust technique is applicable to any ultrathin body semiconductor which demonstrates symmetric ambipolar conduction. Finally, we demonstrate a high gain, high noise margin, chemical doping free, and fully complementary logic inverter based on ambipolar phosphorene FETs.

  9. Characterization of amorphous and nanocrystalline carbon films

    International Nuclear Information System (INIS)

    Chu, Paul K.; Li Liuhe

    2006-01-01

    Amorphous and nanocrystalline carbon films possess special chemical and physical properties such as high chemical inertness, diamond-like properties, and favorable tribological proprieties. The materials usually consist of graphite and diamond microstructures and thus possess properties that lie between the two. Amorphous and nanocrystalline carbon films can exist in different kinds of matrices and are usually doped with a large amount of hydrogen. Thus, carbon films can be classified as polymer-like, diamond-like, or graphite-like based on the main binding framework. In order to characterize the structure, either direct bonding characterization methods or the indirect bonding characterization methods are employed. Examples of techniques utilized to identify the chemical bonds and microstructure of amorphous and nanocrystalline carbon films include optical characterization methods such as Raman spectroscopy, Ultra-violet (UV) Raman spectroscopy, and infrared spectroscopy, electron spectroscopic and microscopic methods such as scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), Auger electron spectroscopy, transmission electron microscopy, and electron energy loss spectroscopy, surface morphology characterization techniques such as scanning probe microscopy (SPM) as well as other characterization methods such as X-ray reflectivity and nuclear magnetic resonance. In this review, the structures of various types of amorphous carbon films and common characterization techniques are described

  10. High mobility polymer gated organic field effect transistor using zinc ...

    Indian Academy of Sciences (India)

    Parylene film prepared by chemical vapour deposition was used as the organic gate insulator. ... properties, due to their spatially extended π-electron system ... tronic defects (Gershenson et al 2006). Parylene forms pin hole free, thin conformal transparent coatings with excellent dielectric and mechanical properties ...

  11. Organic tunnel field effect transistors

    KAUST Repository

    Tietze, Max Lutz

    2017-06-29

    Various examples are provided for organic tunnel field effect transistors (OTFET), and methods thereof. In one example, an OTFET includes a first intrinsic layer (i-layer) of organic semiconductor material disposed over a gate insulating layer; source (or drain) contact stacks disposed on portions of the first i-layer; a second i-layer of organic semiconductor material disposed on the first i-layer surrounding the source (or drain) contact stacks; an n-doped organic semiconductor layer disposed on the second i-layer; and a drain (or source) contact layer disposed on the n-doped organic semiconductor layer. The source (or drain) contact stacks can include a p-doped injection layer, a source (or drain) contact layer, and a contact insulating layer. In another example, a method includes disposing a first i-layer over a gate insulating layer; forming source or drain contact stacks; and disposing a second i-layer, an n-doped organic semiconductor layer, and a drain or source contact.

  12. Ambipolar Phosphorene Field Effect Transistor

    Energy Technology Data Exchange (ETDEWEB)

    Das, Saptarshi [Center for Nanoscale Material and ‡Division of High Energy Physics, Argonne National Laboratory, Argonne, Illinois 60439, United States; Demarteau, Marcel [Center for Nanoscale Material and ‡Division of High Energy Physics, Argonne National Laboratory, Argonne, Illinois 60439, United States; Roelofs, Andreas [Center for Nanoscale Material and ‡Division of High Energy Physics, Argonne National Laboratory, Argonne, Illinois 60439, United States

    2014-10-23

    Two dimensional materials provide an intriguing platform to investigate rich physical phenomena which could ultimately lead to the development of innovative nanotechnologies (1-17). Semiconducting black phosphorous (BP) with high carrier mobility (18-20), anisotropic transport (21, 22) and tunable bandgap (23, 24) is the most recent addition to this exotic class of two dimensional materials. In this article we experimentally demonstrate room temperature quasi ballistic transport of both holes and electrons in ionic liquid gated black phosphorous (BP) field effect transistors (FET) with sub-100nm channel length. The carrier mean free path (mfp) was found to be 15nm for the holes and 5nm for the electrons. By improving the carrier injection through superior electrostatic gate control (EOT=1.5nm), highly symmetric ambipolar conduction with record high hole current of ~0.78mA/µm and electron current of ~0.68mA/µm are achieved for VDD=0.2V. The extracted record low contact resistance of 220Ω-µm is similar to the state of the art Si technology. This is also the best contact resistance value achieved for any two dimensional metal-semiconductor interfaces. Finally, we provide an analytical framework to compare the experimental results with ballistic simulations which includes quantum capacitance considerations.

  13. Diazaisoindigo bithiophene and terthiophene copolymers for application in field-effect transistors and solar cells

    KAUST Repository

    Yue, Wan

    2017-06-10

    Two donor–acceptor conjugated polymers with azaisoindigo as acceptor units and bithiophene and terthiophene as donor units have been synthesized by Stille polymerization. These two polymers have been successfully applied in field-effect transistors and polymer solar cells. By changing the donor component of the conjugated polymer backbone from bithiophene to terthiophene, the density of thiophene in the backbone is increased, manifesting as a decrease in both ionization potential and in electron affinity. Therefore, the charge transport in field-effect transistors switches from ambipolar to predominantly hole transport behavior. PAIIDTT exhibits hole mobility up to 0.40 cm2/Vs and electron mobility of 0.02 cm2/Vs, whereas PAIIDTTT exhibits hole mobility of 0.62 cm2/Vs. Polymer solar cells were fabricated based on these two polymers as donors with PC61BM and PC71BM as acceptor where PAIIDTT shows a modest efficiency of 2.57% with a very low energy loss of 0.55 eV, while PAIIDTTT shows a higher efficiency of 6.16% with a higher energy loss of 0.74 eV. Our results suggest that azaisoindgo is a useful building block for the development of efficient polymer solar cells with further improvement possibility by tuning the alternative units on the polymer backbone. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017

  14. Structural amorphous steels

    International Nuclear Information System (INIS)

    Lu, Z.P.; Liu, C.T.; Porter, W.D.; Thompson, J.R.

    2004-01-01

    Recent advancement in bulk metallic glasses, whose properties are usually superior to their crystalline counterparts, has stimulated great interest in fabricating bulk amorphous steels. While a great deal of effort has been devoted to this field, the fabrication of structural amorphous steels with large cross sections has remained an alchemist's dream because of the limited glass-forming ability (GFA) of these materials. Here we report the discovery of structural amorphous steels that can be cast into glasses with large cross-section sizes using conventional drop-casting methods. These new steels showed interesting physical, magnetic, and mechanical properties, along with high thermal stability. The underlying mechanisms for the superior GFA of these materials are discussed

  15. Study of amorphous semiconductors doped with rare earths (Gd and Er) and conducting polymers by EPR techniques and magnetic susceptibility; Estudo de semicondutores amorfos dopados com terras raras (Gd e Er) e de polimeros condutores atraves das tecnicas de RPE e susceptibilidade magnetica

    Energy Technology Data Exchange (ETDEWEB)

    Sercheli, Mauricio da Silva

    1999-07-01

    This thesis involves the study of amorphous semiconductors and conducting polymers, which have been characterized by EPR and magnetic susceptibility measurements, and to a lesser extent by Raman spectroscopy and RBS. The semiconductors were studied using thin films of silicon doped with rare earth metals, e.g. erbium and gadolinium, which had their magnetic properties studied. Using these studies we could determine the state of valence of the rare earths as well as their concentrations in the silicon matrix. According to our results, the valence of the rare earth metal ions is 3+, and we were able to conclude that 4f electronic shells could not be used for the calculation of the conducting band in this system. Furthermore, the analysis of the data on the magnetic susceptibility of the Er{sup 3+} ion with cubic crystalline acting field, gave us the opportunity to estimate the overall splitting of their electronic states for the first time. The conducting polymers were studied using samples of poly(3-methylthiophene) doped with ClO{sub 4}{sup -}, which show a phase transition in the range of 230 K to 130 K. The electron paramagnetic resonance also gives important information on the crystallization, doping level and the presence of polarons or bipolarons in conducting polymers. (author)

  16. High-Performance Field-Effect Transistors Based on Polystyrene-b-Poly(3-hexylthiophene) Diblock Copolymers

    Energy Technology Data Exchange (ETDEWEB)

    Geohegan, David B [ORNL; Sumpter, Bobby G [ORNL; Hong, Kunlun [ORNL; Xiao, Kai [ORNL; Lavrik, Nickolay V [ORNL; Yu, Xiang [ORNL; Chen, Jihua [ORNL

    2011-01-01

    Polystyrene-b-poly(3-hexylthiophene) (PS-b-P3HT) block copolymers with fixed PS block length have been synthesized by combined atom transfer radical polymerization (ATRP) and Grignard metathesis (GRIM) polymerization. The self-assembled structures of these diblock copolymer thin films based on PS-b-P3HT have been studied by TEM, SAED, GIXD, AFM, and additionally by first principles modeling and simulation. These block copolymers undergo microphase separation and form nanostructured spheres, lamellae, nanofibers, or nanoribbons in the films dictated by the molecular weight of the P3HT block. Within the diblock copolymer thin film, PS blocks segregate to form amorphous domains, and the covalently bonded conjugated P3HT blocks exist as highly ordered crystalline domains through intermolecular packing with their alkyl side chains aligned normal to the substrate while the thiophene rings align parallel to the substrate through stacking. The conjugated PS-b-P3HT block copolymers exhibited significant improvements in organic field-effect transistor (OFET) performance and environmental stability as compared to P3HT homopolymers, with up to a factor of 2 increase in measured mobility (0.08 cm2/(V 3 s)) for the P4 (85 wt % P3HT). Overall, this work demonstrates that the high degree of molecular order induced by block copolymer phase separation can improve the transport properties and stability of conjugating polymers, which are critical for high-performance OFETs and other organic electronics.

  17. Field effect in GeTe thin films

    Energy Technology Data Exchange (ETDEWEB)

    Volker, Hanno; Schlockermann, Carl; Krebs, Daniel; Riedel, Joern; Wuttig, Matthias [RWTH Aachen University, I. Physikalisches Institut (IA), Aachen (Germany)

    2010-07-01

    Phase change memory is a promising candidate to replace common memory technologies such as Flash and DRAM due to its fast switching and excellent scaling perspectives. To improve memory density even further, it was proposed to combine the switchable resistor and the cell selection transistor in a single device. Current control by applying gate voltages has been demonstrated in the works of Yin et al. for Ge{sub 2}Sb{sub 2}Te{sub 5}. Recently, switching within a few nanoseconds has been demonstrated on a different material, GeTe. We therefore studied the field effect in thin films of amorphous GeTe. Dedicated transistor devices were prepared, and the transfer characteristics of these devices were measured as a function of temperature and film thickness. Furthermore, time-dependent behavior was observed and analyzed.

  18. Organic phthalocyanine films with high mobilities for efficient field-effect transistor switches

    Czech Academy of Sciences Publication Activity Database

    Schauer, F.; Zhivkov, I.; Nešpůrek, Stanislav

    266-269, 1-3 (2000), s. 999-1003 ISSN 0022-3093. [International Conference on Amorphous and Microcrystalline Semiconductors /18./. Snowbird, 23.08.1999-27.08.1999] R&D Projects: GA MŠk OC 518.10; GA AV ČR KSK2050602 Institutional research plan: CEZ:AV0Z4050913 Keywords : phthalocyanine * charge mobility * field-effect transistor Subject RIV: CD - Macromolecular Chemistry Impact factor: 1.269, year: 2000

  19. The effect of surfactants on the dissolution behavior of amorphous formulations

    DEFF Research Database (Denmark)

    Mah, Pei T; Peltonen, Leena; Novakovic, Dunja

    2016-01-01

    The optimal design of oral amorphous formulations benefits from the use of excipients to maintain drug supersaturation and thus ensures adequate absorption during intestinal transit. The use of surfactants for the maintenance of supersaturation in amorphous formulations has not been investigated...... in detail. The main aim of this study was to investigate the effect of surfactant on the dissolution behavior of neat amorphous drug and binary polymer based solid dispersion. Indomethacin was used as the model drug and the surfactants studied were polysorbate 80 and poloxamer 407. The presence...... of surfactants (alone or in combination with polymers) in the buffer was detrimental to the dissolution of neat amorphous indomethacin, suggesting that the surfactants promoted the crystallization of neat amorphous indomethacin. In contrast, the presence of surfactants (0.01% w/v) in the buffer resulted...

  20. Making Glasses Conduct: Electrochemical Doping of Redox-Active Polymer Thin Films

    Science.gov (United States)

    Boudouris, Bryan

    Optoelectronically-active macromolecules have been established as promising materials in myriad organic electronic applications (e.g., organic field-effect transistors (OFETs) and organic photovoltaic (OPV) devices). To date, however, the majority of the work surrounding these materials has focused on materials with a great deal of conjugation along their macromolecular backbones and with varying degrees of crystalline structure. Here, we describe an emerging class of macromolecular charge conductors, radical polymers, that: (1) do not contain conjugation and (2) are completely amorphous glasses. Radical polymers contain non-conjugated macromolecular backbones and stable radical sites along the side chains of the electronically-active materials. In contrast to conjugated polymer systems, these materials conduct charge in the solid state through oxidation-reduction (redox) reactions along these pendant groups. Specifically, we demonstrate that controlling the chemical functionality of the pendant groups and the molecular mobility of the macromolecular backbones significantly impacts the charge transport ability of the pristine (i.e., not doped) radical polymers species. Through proper control of these crucial parameters, we show that radical polymers can have electrical conductivity and charge mobility values on par with commonly-used conjugated polymers. Importantly, we also highlight the ability to dope radical polymers with redox-active small molecule species. This doping, in turn, increases the electrical conductivity of the glassy radical polymer thin films in a manner akin to what is observed in traditional conjugated polymer systems. In this way, we establish a means by which to fabricate optically-transparent and colorless thin film glasses capable of conducting charge in a rather rapid manner. We anticipate that these fundamental insights will prove crucial in developing new transparent conducting layers for future electronic applications.

  1. Self-consistent modeling of amorphous silicon devices

    International Nuclear Information System (INIS)

    Hack, M.

    1987-01-01

    The authors developed a computer model to describe the steady-state behaviour of a range of amorphous silicon devices. It is based on the complete set of transport equations and takes into account the important role played by the continuous distribution of localized states in the mobility gap of amorphous silicon. Using one set of parameters they have been able to self-consistently simulate the current-voltage characteristics of p-i-n (or n-i-p) solar cells under illumination, the dark behaviour of field-effect transistors, p-i-n diodes and n-i-n diodes in both the ohmic and space charge limited regimes. This model also describes the steady-state photoconductivity of amorphous silicon, in particular, its dependence on temperature, doping and illumination intensity

  2. Improvement of the physicochemical properties of Co-amorphous naproxen-indomethacin by naproxen-sodium

    DEFF Research Database (Denmark)

    Beyer, Andreas; Grohganz, Holger; Löbmann, Korbinian

    2017-01-01

    Improvement of the physicochemical properties of amorphous active pharmaceutical ingredients (APIs) applying the concept of co-amorphisation is a promising alternative to the use of polymer glass solutions. In co-amorphous systems, the physical stability and the dissolution rate of the involved...... components may be improved in comparison to the respective single amorphous phases. However, for the co-amorphous naproxen-indomethacin model system it has been reported that recrystallization could not be prevented for more than 112days regardless of the applied preparation method and blend ratio...... In the present study, it was thus tested if the physicochemical properties of co-amorphous naproxen-indomethacin could be optimized by incorporation of the naproxen sodium into the system. Three different co-amorphous systems in nine different molar ratios were prepared by quench-cooling: naproxen...

  3. Nanowire Field-Effect Transistors : Sensing Simplicity?

    NARCIS (Netherlands)

    Mescher, M.

    2014-01-01

    Silicon nanowires are structures made from silicon with at least one spatial dimension in the nanometer regime (1-100 nm). From these nanowires, silicon nanowire field-effect transistors can be constructed. Since their introduction in 2001 silicon nanowire field-effect transistors have been studied

  4. Hydrogenated amorphous carbon next deposit after heat treatment

    International Nuclear Information System (INIS)

    Salancon, E.; Durbeck, T.; Schwarz-Selinger, T.; Jacob, W.

    2006-01-01

    One of the main safety problems in the ITER tokamak project is the tritium adsorption in the reactor walls and in particular the deposits which appear after the plasma discharge. These deposits are amorphous hydrogenated carbon films, type polymer (soft a-C:H). The heating of these deposits with a pulse laser is a proposed solution for the tritium desorption. Meanwhile, Gibson and al show that in experimental conditions, products are deposed on the walls before entering the mass spectrometer. The authors present thermo-desorption spectra of different amorphous carbon films. (A.L.B.)

  5. Amorphous Semiconductor Alloys

    Science.gov (United States)

    Madan, Arun

    1985-08-01

    Amorphous silicon (a-Si) based alloys have attracted a considerable amount of interest because of their applications in a wide variety of technologies. However, the major effort has concentrated on inexpensive photovoltaic device applications and has moved from a laboratory curiosity in the early 1970's to viable commercial applications in the 1980's. Impressive progress in this field has been made since the group at University of Dundee demonstrated that a low defect, device quality hydrogenated amorphous silicon (a-Si:H) 12 material could be produced using the radio frequency (r.f.) glow discharge in SiH4 gas ' and that the material could be doped n- and p-type.3 These results spurred a worldwide interest in a-Si based alloys, especially for photovoltaic devices which has resulted in a conversion efficiency approaching 12%. There is now a quest for even higher conversion efficiencies by using the multijunction cell approach. This necessitates the synthesis of new materials of differing bandgaps, which in principle amorphous semiconductors can achieve. In this article, we review some of this work and consider from a device and a materials point of view the hurdles which have to be overcome before this type of concept can be realized.

  6. Photoconductivity and high-field effects in amorphous Se83Te15Zn2 ...

    Indian Academy of Sciences (India)

    Administrator

    well as in the presence of light shows that conduction is through a thermally activated process in both the cases. The activation energy is found to decrease with the increase in light intensity. This indicates the shift of the Fermi level with intensity. Transient photoconductivity measurements at different temperatures indicate.

  7. Photoconductivity and high-field effects in amorphous Se83Te15Zn2 ...

    Indian Academy of Sciences (India)

    quenching technique. The glassy nature of the prepared alloy is confirmed through X-ray diffraction (XRD) technique. A thin film of the aforesaid material was prepared by thermal evaporation technique. Coplanar indium electrode was used.

  8. The Stabilization of Amorphous Zopiclone in an Amorphous Solid Dispersion.

    Science.gov (United States)

    Milne, Marnus; Liebenberg, Wilna; Aucamp, Marique

    2015-10-01

    Zopiclone is a poorly soluble psychotherapeutic agent. The aim of this study was to prepare and characterize an amorphous form of zopiclone as well as the characterization and performance of a stable amorphous solid dispersion. The amorphous form was prepared by the well-known method of quench-cooling of the melt. The solid dispersion was prepared by a solvent evaporation method of zopiclone, polyvinylpyrrolidone-25 (PVP-25), and methanol, followed by freeze-drying. The physico-chemical properties and stability of amorphous zopiclone and the solid dispersion was studied using differential scanning calorimetry (DSC), infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), hot-stage microscopy (HSM), X-ray diffractometry (XRD), solubility, and dissolution studies. The zopiclone amorphous solid-state form was determined to be a fragile glass; it was concluded that the stability of the amorphous form is influenced by both temperature and water. Exposure of amorphous zopiclone to moisture results in rapid transformation of the amorphous form to the crystalline dihydrated form. In comparison, the amorphous solid dispersion proved to be more stable with increased aqueous solubility.

  9. Field-effect and capacitive properties of water-gated transistors based on polythiophene derivatives

    Directory of Open Access Journals (Sweden)

    R. Porrazzo

    2015-01-01

    Full Text Available Recently, water-gated organic field-effect transistors (WGOFET have been intensively studied for their application in the biological field. Surprisingly, a very limited number of conjugated polymers have been reported so far. Here, we systematically explore a series of polythiophene derivatives, presenting different alkyl side chains lengths and orientation, and characterized by various morphologies: comparative evaluation of their performances allows highlighting the critical role played by alkyl side chains, which significantly affects the polymer/water interface capacitance. Reported results provide useful guidelines towards further development of WGOFETs and represent a step forward in the understanding of the polymer/water interface phenomena.

  10. Study of field effect mobility in PCBM films and P3HT : PCBM blends

    NARCIS (Netherlands)

    von Hauff, E; Dyakonov, Vladimir; Parisi, R

    We report on field effect mobility measurements in methanofullerene [6,6]-phenyl C61C61-butyric acid methyl ester (PCBM) films and in blends of poly(3-hexylthiophene) (P3HT) and PCBM, identical to those used in polymer solar cells. Electron mobilities in the order of 10-3cm2/Vs were found in the

  11. High Performance Ambipolar Field-Effect Transistor of Random Network Carbon Nanotubes

    NARCIS (Netherlands)

    Bisri, Satria Zulkarnaen; Gao, Jia; Derenskyi, Vladimir; Gomulya, Widianta; Iezhokin, Igor; Gordiichuk, Pavlo; Herrmann, Andreas; Loi, Maria Antonietta

    2012-01-01

    Ambipolar field-effect transistors of random network carbon nanotubes are fabricated from an enriched dispersion utilizing a conjugated polymer as the selective purifying medium. The devices exhibit high mobility values for both holes and electrons (3 cm(2)/V.s) with a high on/off ratio (10(6)). The

  12. Graphene Field Effect Transistors for Radiation Detection

    Data.gov (United States)

    National Aeronautics and Space Administration — This is propose to develop Graphene Field Effect Transistor based Radiation Sensors (GFET-RS) for NASA Manned Spaceflight Missions anticipated in next several...

  13. Dynamics of polymers

    Energy Technology Data Exchange (ETDEWEB)

    Buchenau, U. [Forschungszentrum Juelich GmbH (Germany). Inst. fuer Energieverfahrenstechnik

    1996-11-01

    Neutron scattering from amorphous polymers allows to switch from incoherent to coherent scattering in the same substance. The power of the tool for the study of the picosecond dynamics of disordered matter is illustrated for polybutadiene, polycarbonate and polystyrene. The results suggest a mixture of sound waves and localized modes, strongly interacting with each other, in the picosecond range. (author) 8 figs., tabs., 39 refs.

  14. Dynamics of polymers

    International Nuclear Information System (INIS)

    Buchenau, U.

    1996-01-01

    Neutron scattering from amorphous polymers allows to switch from incoherent to coherent scattering in the same substance. The power of the tool for the study of the picosecond dynamics of disordered matter is illustrated for polybutadiene, polycarbonate and polystyrene. The results suggest a mixture of sound waves and localized modes, strongly interacting with each other, in the picosecond range. (author) 8 figs., tabs., 39 refs

  15. Amorphous Silk Fibroin Membranes for Separation of CO2

    Science.gov (United States)

    Aberg, Christopher M.; Patel, Anand K.; Gil, Eun Seok; Spontak, Richard J.; Hagg, May-Britt

    2009-01-01

    Amorphous silk fibroin has shown promise as a polymeric material derivable from natural sources for making membranes for use in removing CO2 from mixed-gas streams. For most applications of silk fibroin, for purposes other than gas separation, this material is used in its highly crystalline, nearly natural form because this form has uncommonly high tensile strength. However, the crystalline phase of silk fibroin is impermeable, making it necessary to convert the material to amorphous form to obtain the high permeability needed for gas separation. Accordingly, one aspect of the present development is a process for generating amorphous silk fibroin by treating native silk fibroin in an aqueous methanol/salt solution. The resulting material remains self-standing and can be prepared as thin film suitable for permeation testing. The permeability of this material by pure CO2 has been found to be highly improved, and its mixed-gas permeability has been found to exceed the mixed-gas permeabilities of several ultrahigh-CO2-permeable synthetic polymers. Only one of the synthetic polymers poly(trimethylsilylpropyne) [PTMSP] may be more highly permeable by CO2. PTMSP becomes unstable with time, whereas amorphous silk should not, although at the time of this reporting this has not been conclusively proven.

  16. Sustained-release amorphous solid dispersions.

    Science.gov (United States)

    Maincent, Julien; Williams, Robert O

    2018-03-01

    The use of amorphous solid dispersions (ASD) to overcome poor drug solubility has gained interest in the pharmaceutical industry over the past decade. ASDs are challenging to formulate because they are thermodynamically unstable, and the dispersed drugs tend to recrystallize. Until now, most research on ASDs has focused on immediate-release formulations, supersaturation, and stability; only a few studies have recently reported on the manufacturing of sustained-release ASDs. Sustained-release ASDs can minimize the frequency of administration and prevent high concentrations that can lead to toxicity. Sustained-release ASDs can also decrease the reprecipitation rate in the medium, which can lead to increased bioavailability. However, sustained-release ASDs also pose some significant challenges, such as intramatrix recrystallization, inhibition of drug release as a result of drug-polymer gelling, and low supersaturation due to a slow dissolution rate. This review details the challenges and the formulation approaches that have been investigated to manufacture sustained-release ASDs. In particular, the advantages and drawbacks of hydrophilic polymers, hydrophobic polymers, and lipid-based systems are discussed.

  17. Amorphous Gyroscopic Topological Metamaterials

    Science.gov (United States)

    Mitchell, Noah P.; Nash, Lisa M.; Hexner, Daniel; Turner, Ari M.; Irvine, William T. M.

    Mechanical topological metamaterials display striking mechanical responses, such as unidirectional surface modes that are impervious to disorder. This behavior arises from the topology of their vibrational spectra. All examples of topological metamaterials to date are finely-tuned structures such as crystalline lattices or jammed packings. Here, we present robust recipes for building amorphous topological metamaterials with arbitrary underlying structure and no long-range order. Using interacting gyroscopes as a model system, we demonstrate through experiment, simulation, and theoretical methods that the local geometry and interactions are sufficient to generate topological mobility gaps, allowing for spatially-resolved, real-space calculations of the Chern number. The robustness of our approach enables the design and self-assembly of non-crystalline materials with protected, unidirectional waveguides on the micro and macro scale.

  18. Graphene Field Effect Transistor for Radiation Detection

    Science.gov (United States)

    Li, Mary J. (Inventor); Chen, Zhihong (Inventor)

    2016-01-01

    The present invention relates to a graphene field effect transistor-based radiation sensor for use in a variety of radiation detection applications, including manned spaceflight missions. The sensing mechanism of the radiation sensor is based on the high sensitivity of graphene in the local change of electric field that can result from the interaction of ionizing radiation with a gated undoped silicon absorber serving as the supporting substrate in the graphene field effect transistor. The radiation sensor has low power and high sensitivity, a flexible structure, and a wide temperature range, and can be used in a variety of applications, particularly in space missions for human exploration.

  19. Liquid Crystals for Organic Field-Effect Transistors

    Science.gov (United States)

    O'Neill, Mary; Kelly, Stephen M.

    Columnar, smectic and lamellar polymeric liquid crystals are widely recognized as very promising charge-transporting organic semiconductors due to their ability to spontaneously self-assemble into highly ordered domains in uniform thin films over large areas. The transport properties of smectic and columnar liquid crystals are discussed in Chaps. 2 (10.1007/978-90-481-2873-0_2) and 3 (10.1007/978-90-481-2873-0_3). Here we examine their application to organic field-effect transistors (OFETs): after a short introduction in Sect. 9.1 we introduce the OFET configuration and show how the mobility is measured in Sect. 9.2. Section 9.3 discusses polymeric liquid crystalline semiconductors in OFETs. We review research that shows that annealing of polymers in a fluid mesophase gives a more ordered microcrystalline morphology on cooling than that kinetically determined by solution processing of the thin film. We also demonstrate the benefits of monodomain alignment and show the application of liquid crystals in light-emitting field-effect transistors. Some columnar and smectic phases are highly ordered with short intermolecular separation to give large π-π coupling. We discuss their use in OFETs in Sects. 9.4, and 9.5 respectively. Section 9.6 summarises the conclusions of the chapter.

  20. INFLUENCE OF THE COOLING RATE AND THE BLEND RATIO ON THE PHYSICAL STABILTIY OF CO-AMORPHOUS NAPROXEN/INDOMETHACIN

    DEFF Research Database (Denmark)

    Beyer, Andreas; Grohganz, Holger; Löbmann, Korbinian

    2016-01-01

    Co-amorphisation represents a promising approach to increase the physical stability and dissolution rate of amorphous active pharmaceutical ingredients (APIs) as an alternative to polymer glass solutions. For amorphous and co-amorphous systems, it is reported that the preparation method and the b......Co-amorphisation represents a promising approach to increase the physical stability and dissolution rate of amorphous active pharmaceutical ingredients (APIs) as an alternative to polymer glass solutions. For amorphous and co-amorphous systems, it is reported that the preparation method...... and the blend ratio play major roles with regard to the resulting physical stability. Therefore, in the present study, co-amorphous naproxen-indomethacin (NAP/IND) was prepared by melt-quenching at three different cooling rates and at ten different NAP/IND blend ratios. The samples were analyzed using XRPD...... than samples prepared by intermediate cooling and slow cooling. Intermediate cooling was subsequently used to prepare co-amorphous NAP/IND at different blend ratios. In a previous study, it was postulated that the equimolar (0.5:0.5) co-amorphous blend of NAP/IND is most stable. However, in the present...

  1. Eudragit E100 and Polysaccharide Polymer Blends as Matrices for ...

    African Journals Online (AJOL)

    SCMC) as matrices. Methods: LB, SCMC and E100 were ... Keywords: Drug delivery, Polymer blend, Eudragit, Locust bean gum, Levodopa, Sodium carboxymethylcellulose, Matrix ..... Amorphous Quinapril Hydrochloride. Pharmaceutical. Research ...

  2. Fringing-field effects in acceleration columns

    International Nuclear Information System (INIS)

    Yavor, M.I.; Weick, H.; Wollnik, H.

    1999-01-01

    Fringing-field effects in acceleration columns are investigated, based on the fringing-field integral method. Transfer matrices at the effective boundaries of the acceleration column are obtained, as well as the general transfer matrix of the region separating two homogeneous electrostatic fields with different field strengths. The accuracy of the fringing-field integral method is investigated

  3. Amorphous Hafnium-Indium-Zinc Oxide Semiconductor Thin Film Transistors

    Directory of Open Access Journals (Sweden)

    Sheng-Po Chang

    2012-01-01

    Full Text Available We reported on the performance and electrical properties of co-sputtering-processed amorphous hafnium-indium-zinc oxide (α-HfIZO thin film transistors (TFTs. Co-sputtering-processed α-HfIZO thin films have shown an amorphous phase in nature. We could modulate the In, Hf, and Zn components by changing the co-sputtering power. Additionally, the chemical composition of α-HfIZO had a significant effect on reliability, hysteresis, field-effect mobility (μFE, carrier concentration, and subthreshold swing (S of the device. Our results indicated that we could successfully and easily fabricate α-HfIZO TFTs with excellent performance by the co-sputtering process. Co-sputtering-processed α-HfIZO TFTs were fabricated with an on/off current ratio of ~106, higher mobility, and a subthreshold slope as steep as 0.55 V/dec.

  4. Kinetically Controlled Two-Step Amorphization and Amorphous-Amorphous Transition in Ice

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Chuanlong; Yong, Xue; Tse, John S.; Smith, Jesse S.; Sinogeikin, Stanislav V.; Kenney-Benson, Curtis; Shen, Guoyin

    2017-09-01

    We report the results of in situ structural characterization of the amorphization of crystalline ice Ih under compression and the relaxation of high-density amorphous (HDA) ice under decompression at temperatures between 96 and 160 K by synchrotron x-ray diffraction. The results show that ice Ih transforms to an intermediate crystalline phase at 100 K prior to complete amorphization, which is supported by molecular dynamics calculations. The phase transition pathways show clear temperature dependence: direct amorphization without an intermediate phase is observed at 133 K, while at 145 K a direct Ih-to-IX transformation is observed; decompression of HDA shows a transition to low-density amorphous ice at 96 K and ~ 1 Pa , to ice Ic at 135 K and to ice IX at 145 K. These observations show that the amorphization of compressed ice Ih and the recrystallization of decompressed HDA are strongly dependent on temperature and controlled by kinetic barriers. Pressure-induced amorphous ice is an intermediate state in the phase transition from the connected H-bond water network in low pressure ices to the independent and interpenetrating H-bond network of high-pressure ices.

  5. Diffusion in amorphous media

    Science.gov (United States)

    Iotov, Mihail S.

    The goals of this research are twofold: First, to develop methods and tools for studying problems in chemistry, material science and biology, as well as accurate prediction of the properties of structures and materials of importance to those fields. Second, use those tools to apply the methods to practical problems. In terms of methodology development this thesis focuses on two topics: One: Development of a massively parallel computer program to perform electronic, atomic, molecular levels simulations of problems in chemistry, material science and biology. This computer program uses existing and emerging hardware platforms and parallel tools and is based on decades long research in computer modeling and algorithms. We report on that development in Chapter 3. Two: Development of tools for Molecular Dynamics simulation and methods and tools for course-grained meso-scale modeling of transport properties and especially diffusion of gas penetrants in polymers. We have formulated a new method for extracting coarse-grained information from short (0.2-0.5 nanoseconds [ns]) MD simulations and use this in a meso-scale simulation to calculate diffusion constants in polymer matrices. This is a grid-based method, which calculates the average probability of each grid point of being a void and performs constrained and biased Monte Carlo (MC) dynamics to reach much longer time regimes than possible in MD. The MC method mimics the three regimes of mean square deviation (MSD) behavior seen in MD, thus accounting for the proper mobility of the voids and the compressibility of the polymer matrix. Theoretical discussions and justification for the method is presented in chapter 6. Initial results on He diffusion in a low-density polyethylene (PE) matrix are presented in chapter 7. The behavior at different temperatures follows closely the trend observed from calibrating long term MD for this particular system.

  6. Physicochemical characterization of atorvastatin calcium/ezetimibe amorphous nano-solid dispersions prepared by electrospraying method.

    Science.gov (United States)

    Jahangiri, Azin; Barzegar-Jalali, Mohammad; Javadzadeh, Yousef; Hamishehkar, Hamed; Adibkia, Khosro

    2017-09-01

    In the present study, electrospraying was applied as a novel method for the fabrication of amorphous nano-solid dispersions (N-SDs) of atorvastatin calcium (ATV), ezetimibe (EZT), and ATV/EZT combination as poorly water-soluble drugs. N-SDs were prepared using polyvinylpyrrolidone K30 as an amorphous carrier in 1:1 and 1:5 drug to polymer ratios and the total solid (including drug and polymer) concentrations of 10 and 20% (w/v). The prepared formulations were further investigated for their morphological, physicochemical, and dissolution properties. Scanning electron microscopy studies indicated that the morphology and diameter of the electrosprayed samples (ESs) were influenced by the solution concentration and drug:polymer ratio, so that an increase in the solution concentration resulted in fiber formation while an increase in the polymer ratio led to enhancement of the particle diameter. Differential scanning calorimetry and X-ray powder diffraction studies together with in vitro dissolution test revealed that the ESs were present in an amorphous form with improved dissolution properties. Infrared spectroscopic studies showed hydrogen-bonding interaction between the drug and polymer in ESs. Since the electrospraying method benefits from the both amorphization and nanosizing effect, this novel approach seems to be an efficient method for the fabrication of N-SDs of poorly water-soluble drugs.

  7. Structural morphology of amorphous conducting carbon film

    Indian Academy of Sciences (India)

    Unknown

    been found to be having a lot of technological applica- tions. The properties of these amorphous carbons sensi- tively depend on the relative concentration of sp3 and sp2 hybridized carbons. The resulting amorphous materials are variously referred to as tetrahedral amorphous carbon. (ta-C), amorphous carbon (a-C), ...

  8. Amorphous drugs and dosage forms

    DEFF Research Database (Denmark)

    Grohganz, Holger; Löbmann, K.; Priemel, P.

    2013-01-01

    The transformation to an amorphous form is one of the most promising approaches to address the low solubility of drug compounds, the latter being an increasing challenge in the development of new drug candidates. However, amorphous forms are high energy solids and tend to recry stallize. New...... formulation principles are needed to ensure the stability of amorphous drug forms. The formation of solid dispersions is still the most investigated approach, but additional approaches are desirable to overcome the shortcomings of solid dispersions. Spatial separation by either coating or the use of micro......-containers has shown potential to prevent or delay recrystallization. Another recent approach is the formation of co-amorphous mixtures between either two drugs or one drug and one low molecular weight excipient. Molecular interactions between the two molecules provide an energy barrier that has to be overcome...

  9. Diamond amorphization in neutron irradiation

    International Nuclear Information System (INIS)

    Nikolaenko, V.A.; Gordeev, V.G.

    1996-01-01

    The paper presents the results on neutron irradiation of the diamond in a nuclear reactor. It is shown that the neutron irradiation stimulates the diamond transition to the amorphous state. At a temperature below 750 o K the time required for the diamond-graphite transition decreases with decreasing irradiation temperature. On the contrary, in irradiation at higher temperatures the time of diamond conversion into the amorphous state increases with decreasing but always remains shorter than in the absence of irradiation. (author)

  10. Anomalous magnetoresistance in amorphous metals

    International Nuclear Information System (INIS)

    Kuz'menko, V.M.; Vladychkin, A.N.; Mel'nikov, V.I.; Sudovtsev, A.I.

    1984-01-01

    The magnetoresistance of amorphous Bi, Ca, V and Yb films is investigated in fields up to 4 T at low temperatures. For all metals the magnetoresistance is positive, sharply decreases with growth of temperature and depends anomalously on the magnetic field strength. For amorphous superconductors the results agree satisfactorily with the theory of anomalous magnetoresistance in which allowance is made for scattering of electrons by the superconducting fluctuations

  11. Matrix effects in nilotinib formulations with pH-responsive polymer produced by carbon dioxide-mediated precipitation

    DEFF Research Database (Denmark)

    Colombo, Stefano; Brisander, Magnus; Haglöf, Jakob

    2015-01-01

    . The hybrid particle formulations investigated consisted of amorphous nilotinib embedded in a polymer matrix in single continuous phase, displaying extended retained amorphicity also under wet conditions. It was demonstrated by Raman and FTIR spectroscopy that the efficient drug dispersion and amorphization...

  12. Fundamentals of nanoscaled field effect transistors

    CERN Document Server

    Chaudhry, Amit

    2013-01-01

    Fundamentals of Nanoscaled Field Effect Transistors gives comprehensive coverage of the fundamental physical principles and theory behind nanoscale transistors. The specific issues that arise for nanoscale MOSFETs, such as quantum mechanical tunneling and inversion layer quantization, are fully explored. The solutions to these issues, such as high-κ technology, strained-Si technology, alternate devices structures and graphene technology are also given. Some case studies regarding the above issues and solution are also given in the book. In summary, this book: Covers the fundamental principles behind nanoelectronics/microelectronics Includes chapters devoted to solutions tackling the quantum mechanical effects occurring at nanoscale Provides some case studies to understand the issue mathematically Fundamentals of Nanoscaled Field Effect Transistors is an ideal book for researchers and undergraduate and graduate students in the field of microelectronics, nanoelectronics, and electronics.

  13. Nanowire field effect transistors principles and applications

    CERN Document Server

    Jeong, Yoon-Ha

    2014-01-01

    “Nanowire Field Effect Transistor: Basic Principles and Applications” places an emphasis on the application aspects of nanowire field effect transistors (NWFET). Device physics and electronics are discussed in a compact manner, together with the p-n junction diode and MOSFET, the former as an essential element in NWFET and the latter as a general background of the FET. During this discussion, the photo-diode, solar cell, LED, LD, DRAM, flash EEPROM and sensors are highlighted to pave the way for similar applications of NWFET. Modeling is discussed in close analogy and comparison with MOSFETs. Contributors focus on processing, electrostatic discharge (ESD) and application of NWFET. This includes coverage of solar and memory cells, biological and chemical sensors, displays and atomic scale light emitting diodes. Appropriate for scientists and engineers interested in acquiring a working knowledge of NWFET as well as graduate students specializing in this subject.

  14. Amorphous silicon prepared from silane-hydrogen mixture

    International Nuclear Information System (INIS)

    Pietruszko, S.M.

    1982-09-01

    Amorphous silicon films prepared from a d.c. discharge of 10% SiH 4 - 90% H 2 mixture are found to have properties similar to those made from 100% SiH 4 . These films are found to be quite stable against prolonged light exposure. The effect of nitrogen on the properties of these films was investigated. It was found that instead of behaving as a classical donor, nitrogen introduces deep levels in the material. Field effect experiments on a-Si:H films at the bottom (film-substrate interface) and the top (film-vacuum interface) of the film are also reported. (author)

  15. Planar graphene tunnel field-effect transistor

    OpenAIRE

    Katkov, V. L.; Osipov, V. A.

    2013-01-01

    We propose a concept for a graphene tunnel field-effect transistor. The main idea is based on the use of two graphene electrodes with zigzag termination divided by a narrow gap under the influence of the common gate. Our analysis shows that such device will have a pronounced switching effect at low gate voltage and high on/off current ratio at room temperature.

  16. Highly stable amorphous zinc tin oxynitride thin film transistors under positive bias stress

    Science.gov (United States)

    Niang, K. M.; Bayer, B. C.; Meyer, J. C.; Flewitt, A. J.

    2017-09-01

    The stability of amorphous zinc tin oxynitride thin film transistors (a-ZTON TFTs) under positive bias stress (PBS) is investigated. Thin films are deposited by remote plasma reactive sputtering and are annealed at 300 °C in air for 1 h, after which films are confirmed to be highly amorphous by transmission electron microscopy. Typical a-ZTON TFTs exhibit a threshold voltage of 2.5 V, a field effect mobility of 3.3 cm2 V-1 s-1, a sub-threshold slope of 0.55 V dec-1, and a switching ratio over 106. Using a thermalization energy analysis, the threshold voltage shift under PBS is analysed. A maximum energy barrier to defect conversion up to 0.91 eV is found, which is significantly greater than that of the ˜0.75 eV energy barrier for amorphous indium gallium zinc oxide and amorphous zinc tin oxide TFTs previously reported. The improved stability of these oxynitride TFTs over amorphous oxide TFTs is explained by the elimination of less stable oxygen vacancies due to the passivation of oxygen vacancies with nitrogen. The higher attempt-to-escape frequency of 108 to 109 s-1 in a-ZTON TFTs compared with 107 s-1 in amorphous oxide semiconductor TFTs, on the other hand, is attributed to the high homogeneity of the amorphous film leading to strong carrier localization in the band tails.

  17. Polymer films

    Science.gov (United States)

    Granick, Steve; Sukhishvili, Svetlana A.

    2004-05-25

    A film contains a first polymer having a plurality of hydrogen bond donating moieties, and a second polymer having a plurality of hydrogen bond accepting moieties. The second polymer is hydrogen bonded to the first polymer.

  18. Hydrogenated amorphous silicon photonics

    Science.gov (United States)

    Narayanan, Karthik

    2011-12-01

    Silicon Photonics is quickly proving to be a suitable interconnect technology for meeting the future goals of on-chip bandwidth and low power requirements. However, it is not clear how silicon photonics will be integrated into CMOS chips, particularly microprocessors. The issue of integrating photonic circuits into electronic IC fabrication processes to achieve maximum flexibility and minimum complexity and cost is an important one. In order to minimize usage of chip real estate, it will be advantageous to integrate in three-dimensions. Hydrogenated amorphous silicon (a-Si:H) is emerging as a promising material for the 3-D integration of silicon photonics for on-chip optical interconnects. In addition, a-Si:H film can be deposited using CMOS compatible low temperature plasma-enhanced chemical vapor deposition (PECVD) process at any point in the fabrication process allowing maximum flexibility and minimal complexity. In this thesis, we demonstrate a-Si:H as a high performance alternate platform to crystalline silicon, enabling backend integration of optical interconnects in a hybrid photonic-electronic network-on-chip architecture. High quality passive devices are fabricated on a low-loss a-Si:H platform enabling wavelength division multiplexing schemes. We demonstrate a broadband all-optical modulation scheme based on free-carrier absorption effect, which can enable compact electro-optic modulators in a-Si:H. Furthermore, we comprehensively characterize the optical nonlinearities in a-Si:H and observe that a-Si:H exhibits enhanced nonlinearities as compared to crystalline silicon. Based on the enhanced nonlinearities, we demonstrate low-power four-wave mixing in a-Si:H waveguides enabling high speed all-optical devices in an a-Si:H platform. Finally, we demonstrate a novel data encoding scheme using thermal and all-optical tuning of silicon waveguides, increasing the spectral efficiency in an interconnect link.

  19. Roughening plastic foils as polymer substrates for efficient light trapping in amorphous solar cells; Aufrauhen von Polymersubstraten. Gezieltes Aufrauhen von Plastikfolien fuer ein effizientes Light-Trapping in amorphen Solarzellen

    Energy Technology Data Exchange (ETDEWEB)

    Keppner, H.; Fischer, D.

    2003-07-01

    The objective of the project was the introduction of light-trapping for a-Si:H solar cells deposited on polymer foils by applying plasma roughening of the substrate. The preliminary experiments showed that Reactive Ion Etching (RIE) using SF{sub 6} / O{sub 2} mixtures can result in surface roughnesses of the order of 0.1 to 1 {mu}m. Such surfaces were analysed and compared by using AFM, scanning electron microscopy and angular resolved reflection. Here, the angular resolved reflection proved to be particularly useful as a clear quantitative interpretation is possible on the basis of the critical angle of escape of 28 {sup o}C. Regarding etching parameters to obtain useful roughnesses, it turned out that the electrode configuration plays a predominant role. The best results were obtained by applying a set of powered linear electrode bars in front of the substrate foil. To apply such textured etched substrates to actual solar cell manufacturing, a continuous etching system was realized comprising a linear etching electrode and a roll-to-roll foil transport mechanism capable of treating 300 mm wide foils. In solar cell manufacturing on textured etched films, at first the yield was very low. This was related to a coverage of the etched film with a layer of reaction products. These structures could be eliminated by a cleaning step, leading to an again reasonably high yield. Based on this procedure, n-i-p type solar cells could be successfully manufactured on textured etched polyimide substrates. The increase of the photocurrent and efficiency compared to flat substrates was +10%, with the best solar cell reaching an initial conversion efficiency of 6.9 %. (author)

  20. Pressure Sensitive Insulated Gate Field Effect Transistor

    Science.gov (United States)

    Suminto, James Tjan-Meng

    A pressure sensitive insulated gate field effect transistor has been developed. The device is an elevated gate field-effect-transistor. It consists of a p-type silicon substrate in which two n^+ region, the source and drain, are formed. The gate electrode is a metal film sandwiched in an insulated micro-diaphragm resembling a pill-box which covers the gate oxide, drain, and source. The space between the gate electrode and the oxide is vacuum or an air-gap. When pressure is applied on the diaphragm it deflects and causes a change in the gate capacitance, and thus modulates the conductance of the channel between source and drain. A general theory dealing with the characteristic of this pressure sensitive insulated gate field effect transistor has been derived, and the device fabricated. The fabrication process utilizes the standard integrated circuit fabrication method. It features a batch fabrication of field effect devices followed by the batch fabrication of the deposited diaphragm on top of each field effect device. The keys steps of the diaphragm fabrication are the formation of spacer layer, formation of the diaphragm layer, and the subsequent removal of the spacer layer. The chip size of the device is 600 μm x 1050 mum. The diaphragm size is 200 μm x 200 mum. Characterization of the device has been performed. The current-voltage characteristics with pressure as parameters have been demonstrated and the current-pressure transfer curves obtained. They show non-linear characteristics as those of conventional capacitive pressure sensors. The linearity of threshold voltage versus pressure transfer curves has been demonstrated. The temperature effect on the device performances has been tested. The temperature coefficient of threshold voltage, rather than the electron mobility, has dominated the temperature coefficient of the device. Two temperature compensation schemes have been tested: one method is by connecting two identical PSIGFET in a differential amplifier

  1. Orally Disintegrating Tablets Containing Melt Extruded Amorphous Solid Dispersion of Tacrolimus for Dissolution Enhancement

    Directory of Open Access Journals (Sweden)

    Poovizhi Ponnammal

    2018-03-01

    Full Text Available In order to improve the aqueous solubility and dissolution of Tacrolimus (TAC, amorphous solid dispersions of TAC were prepared by hot melt extrusion with three hydrophilic polymers, Polyvinylpyrrolidone vinyl acetate (PVP VA64, Soluplus® and Hydroxypropyl Cellulose (HPC, at a drug loading of 10% w/w. Molecular modeling was used to determine the miscibility of the drug with the carrier polymers by calculating the Hansen Solubility Parameters. Powder X-ray diffraction and differential scanning calorimetry (DSC studies of powdered solid dispersions revealed the conversion of crystalline TAC to amorphous form. Fourier transform Infrared (FTIR spectroscopy results indicated formation of hydrogen bond between TAC and polymers leading to stabilization of TAC in amorphous form. The extrudates were found to be stable under accelerated storage conditions for 3 months with no re-crystallization, indicating that hot melt extrusion is suitable for producing stable amorphous solid dispersions of TAC in PVP VA64, Soluplus® and HPC. Stable solid dispersions of amorphous TAC exhibited higher dissolution rate, with the solid dispersions releasing more than 80% drug in 15 min compared to the crystalline drug giving 5% drug release in two hours. These stable solid dispersions were incorporated into orally-disintegrating tablets in which the solid dispersion retained its solubility, dissolution and stability advantage.

  2. Orally Disintegrating Tablets Containing Melt Extruded Amorphous Solid Dispersion of Tacrolimus for Dissolution Enhancement.

    Science.gov (United States)

    Ponnammal, Poovizhi; Kanaujia, Parijat; Yani, Yin; Ng, Wai Kiong; Tan, Reginald B H

    2018-03-16

    In order to improve the aqueous solubility and dissolution of Tacrolimus (TAC), amorphous solid dispersions of TAC were prepared by hot melt extrusion with three hydrophilic polymers, Polyvinylpyrrolidone vinyl acetate (PVP VA64), Soluplus ® and Hydroxypropyl Cellulose (HPC), at a drug loading of 10% w / w . Molecular modeling was used to determine the miscibility of the drug with the carrier polymers by calculating the Hansen Solubility Parameters. Powder X-ray diffraction and differential scanning calorimetry (DSC) studies of powdered solid dispersions revealed the conversion of crystalline TAC to amorphous form. Fourier transform Infrared (FTIR) spectroscopy results indicated formation of hydrogen bond between TAC and polymers leading to stabilization of TAC in amorphous form. The extrudates were found to be stable under accelerated storage conditions for 3 months with no re-crystallization, indicating that hot melt extrusion is suitable for producing stable amorphous solid dispersions of TAC in PVP VA64, Soluplus ® and HPC. Stable solid dispersions of amorphous TAC exhibited higher dissolution rate, with the solid dispersions releasing more than 80% drug in 15 min compared to the crystalline drug giving 5% drug release in two hours. These stable solid dispersions were incorporated into orally-disintegrating tablets in which the solid dispersion retained its solubility, dissolution and stability advantage.

  3. Quantum and field effects of oxide heterostructures

    DEFF Research Database (Denmark)

    Trier, Felix

    . In these multi-plexed devices, several inputs aretranslated into several outputs through the multiple physical functionalities.A highly prominent example of such an oxide interface is the one between LaAlO3 and SrTiO3. Although both LaAlO3 and SrTiO3 in the bulk are electrically insulating and non...... aspects of sample preparation will initially be covered. Here, the growth of amorphous-LaAlO3 on SrTiO3 will be addressed in a modified pulsed laser deposition setup. This is followed by an investigation of two high-electron mobility interfaces in SrTiO3-based heterostructures. Specifically...

  4. Refining stability and dissolution rate of amorphous drug formulations

    DEFF Research Database (Denmark)

    Grohganz, Holger; Priemel, Petra A; Löbmann, Korbinian

    2014-01-01

    Introduction: Poor aqueous solubility of active pharmaceutical ingredients (APIs) is one of the main challenges in the development of new small molecular drugs. Additionally, the proportion of poorly soluble drugs among new chemical entities is increasing. The transfer of a crystalline drug to its...... and on the interaction of APIs with small molecular compounds rather than polymers. Finally, in situ formation of an amorphous form might be an option to avoid storage problems altogether. Expert opinion: The diversity of poorly soluble APIs formulated in an amorphous drug delivery system will require different...... approaches for their stabilisation. Thus, increased focus on emerging techniques can be expected and a rational approach to decide the correct formulation is needed....

  5. Functional organic field-effect transistors.

    Science.gov (United States)

    Guo, Yunlong; Yu, Gui; Liu, Yunqi

    2010-10-25

    Functional organic field-effect transistors (OFETs) have attracted increasing attention in the past few years due to their wide variety of potential applications. Research on functional OFETs underpins future advances in organic electronics. In this review, different types of functional OFETs including organic phototransistors, organic memory FETs, organic light emitting FETs, sensors based on OFETs and other functional OFETs are introduced. In order to provide a comprehensive overview of this field, the history, current status of research, main challenges and prospects for functional OFETs are all discussed.

  6. Oxidation and crystal field effects in uranium

    Energy Technology Data Exchange (ETDEWEB)

    Tobin, J. G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Booth, C. H. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Shuh, D. K. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); van der Laan, G. [Diamond Light Source, Didcot (United Kingdom); Sokaras, D. [Stanford Synchrotron Radiation Lightsource, Stanford, CA (United States); Weng, T. -C. [Stanford Synchrotron Radiation Lightsource, Stanford, CA (United States); Yu, S. W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Bagus, P. S. [Univ. of North Texas, Denton, TX (United States); Tyliszczak, T. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Nordlund, D. [Stanford Synchrotron Radiation Lightsource, Stanford, CA (United States)

    2015-07-06

    An extensive investigation of oxidation in uranium has been pursued. This includes the utilization of soft x-ray absorption spectroscopy, hard x-ray absorption near-edge structure, resonant (hard) x-ray emission spectroscopy, cluster calculations, and a branching ratio analysis founded on atomic theory. The samples utilized were uranium dioxide (UO2), uranium trioxide (UO3), and uranium tetrafluoride (UF4). As a result, a discussion of the role of non-spherical perturbations, i.e., crystal or ligand field effects, will be presented.

  7. Towards accurate simulation of fringe field effects

    International Nuclear Information System (INIS)

    Berz, M.; Erdelyi, B.; Makino, K.

    2001-01-01

    In this paper, we study various fringe field effects. Previously, we showed the large impact that fringe fields can have on certain lattice scenarios of the proposed Neutrino Factory. Besides the linear design of the lattice, the effects depend strongly on the details of the field fall off. Various scenarios are compared. Furthermore, in the absence of detailed information, we study the effects for the LHC, a case where the fringe fields are known, and try to draw some conclusions for Neutrino Factory lattices

  8. Dielectric Engineered Tunnel Field-Effect Transistor

    OpenAIRE

    Ilatikhameneh, Hesameddin; Ameen, Tarek A.; Klimeck, Gerhard; Appenzeller, Joerg; Rahman, Rajib

    2015-01-01

    The dielectric engineered tunnel field-effect transistor (DE-TFET) as a high performance steep transistor is proposed. In this device, a combination of high-k and low-k dielectrics results in a high electric field at the tunnel junction. As a result a record ON-current of about 1000 uA/um and a subthreshold swing (SS) below 20mV/dec are predicted for WTe2 DE-TFET. The proposed TFET works based on a homojunction channel and electrically doped contacts both of which are immune to interface stat...

  9. Nanostructures having crystalline and amorphous phases

    Science.gov (United States)

    Mao, Samuel S; Chen, Xiaobo

    2015-04-28

    The present invention includes a nanostructure, a method of making thereof, and a method of photocatalysis. In one embodiment, the nanostructure includes a crystalline phase and an amorphous phase in contact with the crystalline phase. Each of the crystalline and amorphous phases has at least one dimension on a nanometer scale. In another embodiment, the nanostructure includes a nanoparticle comprising a crystalline phase and an amorphous phase. The amorphous phase is in a selected amount. In another embodiment, the nanostructure includes crystalline titanium dioxide and amorphous titanium dioxide in contact with the crystalline titanium dioxide. Each of the crystalline and amorphous titanium dioxide has at least one dimension on a nanometer scale.

  10. Fundamentals of amorphous solids structure and properties

    CERN Document Server

    Stachurski, Zbigniew H

    2014-01-01

    Long awaited, this textbook fills the gap for convincing concepts to describe amorphous solids. Adopting a unique approach, the author develops a framework that lays the foundations for a theory of amorphousness. He unravels the scientific mysteries surrounding the topic, replacing rather vague notions of amorphous materials as disordered crystalline solids with the well-founded concept of ideal amorphous solids. A classification of amorphous materials into inorganic glasses, organic glasses, glassy metallic alloys, and thin films sets the scene for the development of the model of ideal amorph

  11. Optical and electrical properties of electrochemically doped organic field effect transistors

    Science.gov (United States)

    Yumusak, Cigdem; Abbas, Mamatimin; Sariciftci, Niyazi Serdar

    2013-01-01

    Mixed ionic/electronic conduction in conducting polymers introduces new physics/chemistry and an additional functionality in organic optoelectronic devices. The incorporation of an ionic species in a conjugated polymer matrix results in the increase in electrical conductivity associated with the electrochemical doping of the material. In recent years polymer light emitting electrochemical cells (LECs) have been demonstrated. In such electrochemical optoelectronic devices, mobile ions facilitate the efficient injection of electronic charge carriers creating “in situ” doping regions near the electrodes and lead to efficient electroluminescence light emission. Here, we introduce the same concept of an LEC in the organic field effect transistors (OFETs). The presence of both electronic and ionic charge carriers in the active layers of OFETs brings high charge carrier mobility and light emission even using symmetric source and drain metal electrodes. PMID:23482672

  12. Thermal properties of polymers below 4 K.

    Science.gov (United States)

    Salinger, G. L.

    1972-01-01

    Obtained measurement data on the Debye contribution to the specific heat, the specific heat, and the thermal conductivity in polymers below 4 deg K are discussed. The results obtained suggest that impurities are responsible for the apparent thermal properties of polymers and glasses at low temperatures. In order to determine the intrinsic behavior of amorphous solids, measurements must be made at temperatures low enough to freeze out the local modes.

  13. Amorphous nanoparticles — Experiments and computer simulations

    International Nuclear Information System (INIS)

    Hoang, Vo Van; Ganguli, Dibyendu

    2012-01-01

    The data obtained by both experiments and computer simulations concerning the amorphous nanoparticles for decades including methods of synthesis, characterization, structural properties, atomic mechanism of a glass formation in nanoparticles, crystallization of the amorphous nanoparticles, physico-chemical properties (i.e. catalytic, optical, thermodynamic, magnetic, bioactivity and other properties) and various applications in science and technology have been reviewed. Amorphous nanoparticles coated with different surfactants are also reviewed as an extension in this direction. Much attention is paid to the pressure-induced polyamorphism of the amorphous nanoparticles or amorphization of the nanocrystalline counterparts. We also introduce here nanocomposites and nanofluids containing amorphous nanoparticles. Overall, amorphous nanoparticles exhibit a disordered structure different from that of corresponding bulks or from that of the nanocrystalline counterparts. Therefore, amorphous nanoparticles can have unique physico-chemical properties differed from those of the crystalline counterparts leading to their potential applications in science and technology.

  14. Model for amorphous aggregation processes

    Science.gov (United States)

    Stranks, Samuel D.; Ecroyd, Heath; van Sluyter, Steven; Waters, Elizabeth J.; Carver, John A.; von Smekal, Lorenz

    2009-11-01

    The amorphous aggregation of proteins is associated with many phenomena, ranging from the formation of protein wine haze to the development of cataract in the eye lens and the precipitation of recombinant proteins during their expression and purification. While much literature exists describing models for linear protein aggregation, such as amyloid fibril formation, there are few reports of models which address amorphous aggregation. Here, we propose a model to describe the amorphous aggregation of proteins which is also more widely applicable to other situations where a similar process occurs, such as in the formation of colloids and nanoclusters. As first applications of the model, we have tested it against experimental turbidimetry data of three proteins relevant to the wine industry and biochemistry, namely, thaumatin, a thaumatinlike protein, and α -lactalbumin. The model is very robust and describes amorphous experimental data to a high degree of accuracy. Details about the aggregation process, such as shape parameters of the aggregates and rate constants, can also be extracted.

  15. Amorphous metal matrix composite ribbons

    International Nuclear Information System (INIS)

    Barczy, P.; Szigeti, F.

    1998-01-01

    Composite ribbons with amorphous matrix and ceramic (SiC, WC, MoB) particles were produced by modified planar melt flow casting methods. Weldability, abrasive wear and wood sanding examinations were carried out in order to find optimal material and technology for elevated wear resistance and sanding durability. The correlation between structure and composite properties is discussed. (author)

  16. Atomistic Models of Amorphous Semiconductors

    NARCIS (Netherlands)

    Jarolimek, K.

    2011-01-01

    Crystalline silicon is probably the best studied material, widely used by the semiconductor industry. The subject of this thesis is an intriguing form of this element namely amorphous silicon. It can contain a varying amount of hydrogen and is denoted as a-Si:H. It completely lacks the neat long

  17. Fracture Phenomena in Amorphous Selenium

    DEFF Research Database (Denmark)

    Lindegaard-Andersen, Asger; Dahle, Birgit

    1966-01-01

    Fracture surfaces of amorphous selenium broken in flexure at room temperature have been studied. The fracture velocity was found to vary in different regions of the fracture surface. Peculiar features were observed in a transition zone between fast and slower fracture. In this zone cleavage steps...

  18. Individual SWCNT based ionic field effect transistor

    Science.gov (United States)

    Pang, Pei; He, Jin; Park, Jae Hyun; Krstic, Predrag; Lindsay, Stuart

    2011-03-01

    Here we report that the ionic current through a single-walled carbon nanotube (SWCNT) can be effectively gated by a perpendicular electrical field from a top gate electrode, working as ionic field effect transistor. Both our experiment and simulation confirms that the electroosmotic current (EOF) is the main component in the ionic current through the SWCNT and is responsible for the gating effect. We also studied the gating efficiency as a function of solution concentration and pH and demonstrated that the device can work effectively in the physiological relevant condition. This work opens the door to use CNT based nanofluidics for ion and molecule manipulation. This work was supported by the DNA Sequencing Technology Program of the National Human Genome Research Institute (1RC2HG005625-01, 1R21HG004770-01), Arizona Technology Enterprises and the Biodesign Institute.

  19. Antiferromagnetic Spin Wave Field-Effect Transistor

    Science.gov (United States)

    Cheng, Ran; Daniels, Matthew W.; Zhu, Jian-Gang; Xiao, Di

    2016-01-01

    In a collinear antiferromagnet with easy-axis anisotropy, symmetry dictates that the spin wave modes must be doubly degenerate. Theses two modes, distinguished by their opposite polarization and available only in antiferromagnets, give rise to a novel degree of freedom to encode and process information. We show that the spin wave polarization can be manipulated by an electric field induced Dzyaloshinskii-Moriya interaction and magnetic anisotropy. We propose a prototype spin wave field-effect transistor which realizes a gate-tunable magnonic analog of the Faraday effect, and demonstrate its application in THz signal modulation. Our findings open up the exciting possibility of digital data processing utilizing antiferromagnetic spin waves and enable the direct projection of optical computing concepts onto the mesoscopic scale. PMID:27048928

  20. Vertically Integrated Multiple Nanowire Field Effect Transistor.

    Science.gov (United States)

    Lee, Byung-Hyun; Kang, Min-Ho; Ahn, Dae-Chul; Park, Jun-Young; Bang, Tewook; Jeon, Seung-Bae; Hur, Jae; Lee, Dongil; Choi, Yang-Kyu

    2015-12-09

    A vertically integrated multiple channel-based field-effect transistor (FET) with the highest number of nanowires reported ever is demonstrated on a bulk silicon substrate without use of wet etching. The driving current is increased by 5-fold due to the inherent vertically stacked five-level nanowires, thus showing good feasibility of three-dimensional integration-based high performance transistor. The developed fabrication process, which is simple and reproducible, is used to create multiple stiction-free and uniformly sized nanowires with the aid of the one-route all-dry etching process (ORADEP). Furthermore, the proposed FET is revamped to create nonvolatile memory with the adoption of a charge trapping layer for enhanced practicality. Thus, this research suggests an ultimate design for the end-of-the-roadmap devices to overcome the limits of scaling.

  1. Field-effect P-N junction

    Science.gov (United States)

    Regan, William; Zettl, Alexander

    2015-05-05

    This disclosure provides systems, methods, and apparatus related to field-effect p-n junctions. In one aspect, a device includes an ohmic contact, a semiconductor layer disposed on the ohmic contact, at least one rectifying contact disposed on the semiconductor layer, a gate including a layer disposed on the at least one rectifying contact and the semiconductor layer and a gate contact disposed on the layer. A lateral width of the rectifying contact is less than a semiconductor depletion width of the semiconductor layer. The gate contact is electrically connected to the ohmic contact to create a self-gating feedback loop that is configured to maintain a gate electric field of the gate.

  2. Modeling quantization effects in field effect transistors

    CERN Document Server

    Troger, C

    2001-01-01

    Numerical simulation in the field of semiconductor device development advanced to a valuable, cost-effective and flexible facility. The most widely used simulators are based on classical models, as they need to satisfy time and memory constraints. To improve the performance of field effect transistors such as MOSFETs and HEMTs these devices are continuously scaled down in their dimensions. Consequently the characteristics of such devices are getting more and more determined by quantum mechanical effects arising from strong transversal fields in the channel. In this work an approach based on a two-dimensional electron gas is used to describe the confinement of the carriers. Quantization is considered in one direction only. For the derivation of a one-dimensional Schroedinger equation in the effective mass framework a non-parabolic correction for the energy dispersion due to Kane is included. For each subband a non-parabolic dispersion relation characterized by subband masses and subband non-parabolicity coeffi...

  3. Field Effect Microparticle Generation for Cell Microencapsulation.

    Science.gov (United States)

    Hsu, Brend Ray-Sea; Fu, Shin-Huei

    2017-01-01

    The diameter and sphericity of alginate-poly-L-lysine-alginate microcapsules, determined by the size and the shape of calcium alginate microspheres, affect their in vivo durability and biocompatibility and the results of transplantation. The commonly used air-jet spray method generates microspheres with a wider variation in diameter, larger sphere morphology, and evenly distributed encapsulated cells. In order to overcome these drawbacks, we designed a field effect microparticle generator to create a stable electric field to prepare microparticles with a smaller diameter and more uniform morphology. Using this electric field microparticle generator the encapsulated cells will be located at the periphery of the microspheres, and thus the supply of oxygen and nutrients for the encapsulated cells will be improved compared with the centrally located encapsulated cells in the air-jet spray method.

  4. CLASSIFICATION OF BIODEGRADABLE POLYMERS

    Directory of Open Access Journals (Sweden)

    I. I. Karpunin

    2015-01-01

    Full Text Available The executed investigations have made it possible to ascertain that a morphological structure of starch granules mainly determine technological peculiarities of starch isolation from raw material, its modification and its later use. Morphological structure of starch granules primarily depends on type of plant starch-containing raw material which has been used for its isolation. Class of raw material exerts a strong impact on the shape and size of the granules. Linear “light” amylose chains and “heavy” amylopectin branch chains form a starch granule ultrastructure. X-ray research has proved that starch granules are characterized by presence of interlacing amorphous and crystalline regions. In this case polymer orientation using stretching of the obtained end product influences on its physical and mechanical  indices which are increasing due to polymer orientation. For the purpose of packaging orientation of polymer films can solve such important problems as significant improvement of operational properties, creation of  thermosetting film materials, improvement of qualitative indices of the recycled film.Results of the conducted research have proved the fact that it is necessary to make changes in technology in order to increase biological degradability of the recycled packaging made from polymers and improve physical and mechanical indices. In this regard film production technology presupposes usage of such substances as stark and others which are characterized by rather large presence of branch chains of molecules and interlacing amorphous and crystalline regions. Such approach makes it possible to obtain after-use package which is strong and quickly degradable by micro-organisms.

  5. Synthesis and high temperature stability of amorphous Si(B)CN-MWCNT composite nanowires

    Science.gov (United States)

    Bhandavat, Romil; Singh, Gurpreet

    2012-02-01

    We demonstrate synthesis of a hybrid nanowire structure consisting of an amorphous polymer-derived silicon boron-carbonitride (Si-B-C-N) shell with a multiwalled carbon nanotube core. This was achieved through a novel process involving preparation of a boron-modified liquid polymeric precursor through a reaction of trimethyl borate and polyureasilazane under atmospheric conditions; followed by conversion of polymer to glass-ceramic on carbon nanotube surfaces through controlled heating. Chemical structure of the polymer was studied by liquid-NMR while evolution of various ceramic phases was studied by Raman spectroscopy, solid-NMR, Fourier transform infrared and X-ray photoelectron spectroscopy. Electron microscopy and X-ray diffraction confirms presence of amorphous Si(B)CN coating on individual nanotubes for all specimen processed below 1400 degree C. Thermogravimetric analysis, followed by TEM revealed high temperature stability of the carbon nanotube core in flowing air up to 1300 degree C.

  6. Formation of Micro and Mesoporous Amorphous Silica-Based Materials from Single Source Precursors

    Directory of Open Access Journals (Sweden)

    Mohd Nazri Mohd Sokri

    2016-03-01

    Full Text Available Polysilazanes functionalized with alkoxy groups were designed and synthesized as single source precursors for fabrication of micro and mesoporous amorphous silica-based materials. The pyrolytic behaviors during the polymer to ceramic conversion were studied by the simultaneous thermogravimetry-mass spectrometry (TG-MS analysis. The porosity of the resulting ceramics was characterized by the N2 adsorption/desorption isotherm measurements. The Fourier transform infrared spectroscopy (FT-IR and Raman spectroscopic analyses as well as elemental composition analysis were performed on the polymer-derived amorphous silica-based materials, and the role of the alkoxy group as a sacrificial template for the micro and mesopore formations was discussed from a viewpoint to establish novel micro and mesoporous structure controlling technologies through the polymer-derived ceramics (PDCs route.

  7. P-type field effect transistor based on Na-doped BaSnO3

    Science.gov (United States)

    Jang, Yeaju; Hong, Sungyun; Park, Jisung; Char, Kookrin

    We fabricated field effect transistors (FET) based on the p-type Na-doped BaSnO3 (BNSO) channel layer. The properties of epitaxial BNSO channel layer were controlled by the doping rate. In order to modulate the p-type FET, we used amorphous HfOx and epitaxial BaHfO3 (BHO) gate oxides, both of which have high dielectric constants. HfOx was deposited by atomic-layer-deposition and BHO was epitaxially grown by pulsed laser deposition. The pulsed laser deposited SrRuO3 (SRO) was used as the source and the drain contacts. Indium-tin oxide and La-doped BaSnO3 were used as the gate electrodes on top of the HfOx and the BHO gate oxides, respectively. We will analyze and present the performances of the BNSO field effect transistor such as the IDS-VDS, the IDS-VGS, the Ion/Ioff ratio, and the field effect mobility. Samsung Science and Technology Foundation.

  8. Biodegradable Polymers

    OpenAIRE

    Vroman, Isabelle; Tighzert, Lan

    2009-01-01

    Biodegradable materials are used in packaging, agriculture, medicine and other areas. In recent years there has been an increase in interest in biodegradable polymers. Two classes of biodegradable polymers can be distinguished: synthetic or natural polymers. There are polymers produced from feedstocks derived either from petroleum resources (non renewable resources) or from biological resources (renewable resources). In general natural polymers offer fewer advantages than synthetic polymers. ...

  9. Field effect sensors for PCR applications

    Science.gov (United States)

    Taing, Meng-Houit; Sweatman, Denis R.

    2004-03-01

    The use of field effect sensors for biological and chemical sensing is widely employed due to its ability to make detections based on charge and surface potential. Because proteins and DNA almost always carry a charge [1], silicon can be used to micro fabricate such a sensor. The EIS structure (Electrolyte on Insulator on Silicon) provides a novel, label-free and simple to fabricate way to make a field effect DNA detection sensor. The sensor responds to fluctuating capacitance caused by a depletion layer thickness change at the surface of the silicon substrate through DNA adsorption onto the dielectric oxide/PLL (Poly-L-Lysine) surface. As DNA molecules diffuse to the sensor surface, they are bound to their complimentary capture probes deposited on the surface. The negative charge exhibited by the DNA forces negative charge carriers in the substrate to move away from the surface. This causes an n-type depletion layer substrate to thicken and a p-type to thin. The depletion layer thickness can be measured by its capacitance using an LCR meter. This experiment is conducted using the ConVolt (constant voltage) approach. Nucleic acids are amplified by an on chip PCR (Polymerase Chain Reaction) system and then fed into the sensor. The low ionic solution strength will ensure that counter-ions do not affect the sensor measurements. The sensor surface contains capture probes that bind to the pathogen. The types of pathogens we"ll be detecting include salmonella, campylobacter and E.Coli DNA. They are held onto the sensor surface by the positively charged Poly-L-Lysine layer. The electrolyte is biased through a pseudo-reference electrode. Pseudo reference electrodes are usually made from metals such as Platinum or Silver. The problem associated with "floating" biasing electrodes is they cannot provide stable biasing potentials [2]. They drift due to surface charging effects and trapped charges on the surface. To eliminate this, a differential system consisting of 2 sensors

  10. Solubility Advantage (and Disadvantage) of Pharmaceutical Amorphous Solid Dispersions.

    Science.gov (United States)

    Huang, Siyuan; Mao, Chen; Williams, Robert O; Yang, Chia-Yi

    2016-12-01

    The solubility of a drug is ultimately governed by its chemical potential as it is present in the undissolved solute. For a pharmaceutical amorphous solid dispersion (ASD), its solubility depends on the state and composition of the undissolved solute when the ASD is equilibrated with water. Concerning the undissolved solute phase that can contain up to 3 components (drug, polymer, and water), we developed a complete thermodynamic model to calculate the chemical potential of a drug in the multicomponent, amorphous system. This approach enables the estimation of the true solubility advantage of ASD from calorimetric measurements and moisture sorption isotherms. Both theoretical estimation and experimental studies, using indomethacin (IMC)/Eudragit E ASD systems, show that the solubility advantage of the amorphous IMC is significantly reduced through ASD formation and water partitioning. For the ASD with 70% drug loading, the solubility of IMC is lower than its crystalline counterpart. Our results show that stabilization through the ASD formation and water sorption can be manifested by the lowering of drug solubility; they demonstrate that the core property in ASD development is the drug chemical potential, which is essentially the thermodynamic driving force and can be quantitated using the model presented in this work. Copyright © 2016 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

  11. Amorphous metal based nanoelectromechanical switch

    KAUST Repository

    Mayet, Abdulilah M.

    2013-04-01

    Nanoelectromechanical (NEM) switch is an interesting ultra-low power option which can operate in the harsh environment and can be a complementary element in complex digital circuitry. Although significant advancement is happening in this field, report on ultra-low voltage (pull-in) switch which offers high switching speed and area efficiency is yet to be made. One key challenge to achieve such characteristics is to fabricate nano-scale switches with amorphous metal so the shape and dimensional integrity are maintained to achieve the desired performance. Therefore, we report a tungsten alloy based amorphous metal with fabrication process development of laterally actuated dual gated NEM switches with 100 nm width and 200 nm air-gap to result in <5 volts of actuation voltage (Vpull-in). © 2013 IEEE.

  12. Optical and electrical properties of electrochemically doped organic field effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Yumusak, Cigdem, E-mail: yumusak@yildiz.edu.tr [Department of Physics, Faculty of Arts and Sciences, Yildiz Technical University, Davutpasa Campus, Esenler, 34210 Istanbul (Turkey); Linz Institute for Organic Solar Cells (LIOS), Physical Chemistry, Johannes Kepler University of Linz, A-4040 Linz (Austria); Abbas, Mamatimin; Sariciftci, Niyazi Serdar [Linz Institute for Organic Solar Cells (LIOS), Physical Chemistry, Johannes Kepler University of Linz, A-4040 Linz (Austria)

    2013-02-15

    Mixed ionic/electronic conduction in conducting polymers introduces new physics/chemistry and an additional functionality in organic optoelectronic devices. The incorporation of an ionic species in a conjugated polymer matrix results in the increase in electrical conductivity associated with the electrochemical doping of the material. In recent years polymer light emitting electrochemical cells (LECs) have been demonstrated. In such electrochemical optoelectronic devices, mobile ions facilitate the efficient injection of electronic charge carriers creating 'in situ' doping regions near the electrodes and lead to efficient electroluminescence light emission. Here, we introduce the same concept of an LEC in the organic field effect transistors (OFETs). The presence of both electronic and ionic charge carriers in the active layers of OFETs brings high charge carrier mobility and light emission even using symmetric source and drain metal electrodes. - Highlights: Black-Right-Pointing-Pointer Light emission from an electrochemically doped organic field effect transistor. Black-Right-Pointing-Pointer High charge carrier mobility as high as 3 cm{sup 2} V{sup -1} s{sup -1}. Black-Right-Pointing-Pointer Light emission intensity can be controlled by the gate as well as drain voltages.

  13. Transient photoconductivity in amorphous semiconductors

    International Nuclear Information System (INIS)

    Mpawenayo, P.

    1997-07-01

    Localized states in amorphous semiconductors are divided in disorder induced shallow trap levels and dangling bonds deep states. Dangling bonds are assumed here to be either neutral or charged and their energy distribution is a single gaussian. Here, it is shown analytically that transient photocurrent in amorphous semiconductors is fully controlled by charge carriers transitions between localized states for one part and tunneling hopping carriers on the other. Localized dangling bonds deep states act as non radiative recombination centres, while hopping tunnelling is assisted by the Coulomb interaction between defects sites. The half-width of defects distribution is the disorder parameter that determines the carrier hopping time between defects sites. The macroscopic time that explains the long decay response times observed will all types of amorphous semiconductors is duly thought to be temperature dependent. Basic equations developed by Longeaud and Kleider are solved for the general case of a semiconductor after photo-generation. It turns out that the transient photoconductivity decay has two components; one with short response times from carriers trap-release transitions between shallow levels and extended states and a hopping component made of inter-dependent exponentials whose time constants span in larger ranges depending on disorder. The photoconductivity hopping component appears as an additional term to be added to photocurrents derived from existing models. The results of the present study explain and complete the power law decay derived in the multiple trapping models developed 20 years ago only in the approximation of the short response time regime. The long response time regime is described by the hopping macroscopic time. The present model is verified for all samples of amorphous semiconductors known so far. Finally, it is proposed to improved the modulated photoconductivity calculation techniques by including the long-lasting hopping dark documents

  14. Uranium incorporation into amorphous silica.

    Science.gov (United States)

    Massey, Michael S; Lezama-Pacheco, Juan S; Nelson, Joey M; Fendorf, Scott; Maher, Kate

    2014-01-01

    High concentrations of uranium are commonly observed in naturally occurring amorphous silica (including opal) deposits, suggesting that incorporation of U into amorphous silica may represent a natural attenuation mechanism and promising strategy for U remediation. However, the stability of uranium in opaline silicates, determined in part by the binding mechanism for U, is an important factor in its long-term fate. U may bind directly to the opaline silicate matrix, or to materials such as iron (hydr)oxides that are subsequently occluded within the opal. Here, we examine the coordination environment of U within opaline silica to elucidate incorporation mechanisms. Precipitates (with and without ferrihydrite inclusions) were synthesized from U-bearing sodium metasilicate solutions, buffered at pH ∼ 5.6. Natural and synthetic solids were analyzed with X-ray absorption spectroscopy and a suite of other techniques. In synthetic amorphous silica, U was coordinated by silicate in a double corner-sharing coordination geometry (Si at ∼ 3.8-3.9 Å) and a small amount of uranyl and silicate in a bidentate, mononuclear (edge-sharing) coordination (Si at ∼ 3.1-3.2 Å, U at ∼ 3.8-3.9 Å). In iron-bearing synthetic solids, U was adsorbed to iron (hydr)oxide, but the coordination environment also contained silicate in both edge-sharing and corner-sharing coordination. Uranium local coordination in synthetic solids is similar to that of natural U-bearing opals that retain U for millions of years. The stability and extent of U incorporation into opaline and amorphous silica represents a long-term repository for U that may provide an alternative strategy for remediation of U contamination.

  15. Pressure-jump induced rapid solidification of melt: a method of preparing amorphous materials

    Science.gov (United States)

    Liu, Xiuru; Jia, Ru; Zhang, Doudou; Yuan, Chaosheng; Shao, Chunguang; Hong, Shiming

    2018-04-01

    By using a self-designed pressure-jump apparatus, we investigated the melt solidification behavior in rapid compression process for several kinds of materials, such as elementary sulfur, polymer polyether-ether-ketone (PEEK) and poly-ethylene-terephthalate, alloy La68Al10Cu20Co2 and Nd60Cu20Ni10Al10. Experimental results clearly show that their melts could be solidified to be amorphous states through the rapid compression process. Bulk amorphous PEEK with 24 mm in diameter and 12 mm in height was prepared, which exceeds the size obtained by melt quenching method. The bulk amorphous sulfur thus obtained exhibited extraordinarily high thermal stability, and an abnormal exothermic transition to liquid sulfur was observed at around 396 K for the first time. Furthermore, it is suggested that the glass transition pressure and critical compression rate exist to form the amorphous phase. This approach of rapid compression is very attractive not only because it is a new technique of make bulk amorphous materials, but also because novel properties are expected in the amorphous materials solidified by the pressure-jump within milliseconds or microseconds.

  16. Amorphous formulations of indomethacin and griseofulvin prepared by electrospinning.

    Science.gov (United States)

    Lopez, Felipe L; Shearman, Gemma C; Gaisford, Simon; Williams, Gareth R

    2014-12-01

    Following an array of optimization experiments, two series of electrospun polyvinylpyrrolidone (PVP) fibers were prepared. One set of fibers contained various loadings of indomethacin, known to form stable glasses, and the other griseofulvin (a poor glass former). Drug loadings of up to 33% w/w were achieved. Electron microscopy data showed the fibers largely to comprise smooth and uniform cylinders, with evidence for solvent droplets in some samples. In all cases, the drug was found to exist in the amorphous physical state in the fibers on the basis of X-ray diffraction and differential scanning calorimetry (DSC) measurements. Modulated temperature DSC showed that the relationship between a formulation's glass transition temperature (Tg) and the drug loading follows the Gordon-Taylor equation, but not the Fox equation. The results of Gordon-Taylor analysis indicated that the drug/polymer interactions were stronger with indomethacin. The interactions between drug and polymer were explored in more detail using molecular modeling simulations and again found to be stronger with indomethacin; the presence of significant intermolecular forces was further confirmed using IR spectroscopy. The amorphous form of both drugs was found to be stable after storage of the fibers for 8 months in a desiccator (relative humidity <25%). Finally, the functional performance of the fibers was studied; in all cases, the drug-loaded fibers released their drug cargo very rapidly, offering accelerated dissolution over the pure drug.

  17. Fringing field effects in negative capacitance field-effect transistors with a ferroelectric gate insulator

    Science.gov (United States)

    Hattori, Junichi; Fukuda, Koichi; Ikegami, Tsutomu; Ota, Hiroyuki; Migita, Shinji; Asai, Hidehiro; Toriumi, Akira

    2018-04-01

    We study the effects of fringing electric fields on the behavior of negative-capacitance (NC) field-effect transistors (FETs) with a silicon-on-insulator body and a gate stack consisting of an oxide film, an internal metal film, a ferroelectric film, and a gate electrode using our own device simulator that can properly handle the complicated relationship between the polarization and the electric field in ferroelectric materials. The behaviors of such NC FETs and the corresponding metal-oxide-semiconductor (MOS) FETs are simulated and compared with each other to evaluate the effects of the NC of the ferroelectric film. Then, the fringing field effects are evaluated by comparing the NC effects in NC FETs with and without gate spacers. The fringing field between the gate stack, especially the internal metal film, and the source/drain region induces more charges at the interface of the film with the ferroelectric film. Accordingly, the function of the NC to modulate the gate voltage and the resulting function to improve the subthreshold swing are enhanced. We also investigate the relationships of these fringing field effects to the drain voltage and four design parameters of NC FETs, i.e., gate length, gate spacer permittivity, internal metal film thickness, and oxide film thickness.

  18. Electric Field Effects in RUS Measurements

    Energy Technology Data Exchange (ETDEWEB)

    Darling, Timothy W [Los Alamos National Laboratory; Ten Cate, James A [Los Alamos National Laboratory; Allured, Bradley [UNIV NEVADA, RENO; Carpenter, Michael A [CAMBRIDGE UNIV. UK

    2009-09-21

    Much of the power of the Resonant Ultrasound Spectroscopy (RUS) technique is the ability to make mechanical resonance measurements while the environment of the sample is changed. Temperature and magnetic field are important examples. Due to the common use of piezoelectric transducers near the sample, applied electric fields introduce complications, but many materials have technologically interesting responses to applied static and RF electric fields. Non-contact optical, buffered, or shielded transducers permit the application of charge and externally applied electric fields while making RUS measurements. For conducting samples, in vacuum, charging produces a small negative pressure in the volume of the material - a state rarely explored. At very high charges we influence the electron density near the surface so the propagation of surface waves and their resonances may give us a handle on the relationship of electron density to bond strength and elasticity. Our preliminary results indicate a charge sign dependent effect, but we are studying a number of possible other effects induced by charging. In dielectric materials, external electric fields influence the strain response, particularly in ferroelectrics. Experiments to study this connection at phase transformations are planned. The fact that many geological samples contain single crystal quartz suggests a possible use of the piezoelectric response to drive vibrations using applied RF fields. In polycrystals, averaging of strains in randomly oriented crystals implies using the 'statistical residual' strain as the drive. The ability to excite vibrations in quartzite polycrystals and arenites is explored. We present results of experimental and theoretical approaches to electric field effects using RUS methods.

  19. Organic semiconductors for solution-processable field-effect transistors (OFETs).

    Science.gov (United States)

    Allard, Sybille; Forster, Michael; Souharce, Benjamin; Thiem, Heiko; Scherf, Ullrich

    2008-01-01

    The cost-effective production of flexible electronic components will profit considerably from the development of solution-processable, organic semiconductor materials. Particular attention is focused on soluble semiconductors for organic field-effect transistors (OFETs). The hitherto differentiation between "small molecules" and polymeric materials no longer plays a role, rather more the ability to process materials from solution to homogeneous semiconducting films with optimal electronic properties (high charge-carrier mobility, low threshold voltage, high on/off ratio) is pivotal. Key classes of materials for this purpose are soluble oligoacenes, soluble oligo- and polythiophenes and their respective copolymers, and oligo- and polytriarylamines. In this context, micro- or nanocrystalline materials have the general advantage of somewhat higher charge-carrier mobilities, which, however, could be offset in the case of amorphous, glassy materials by simpler and more reproducible processing.

  20. Colloidal Photoluminescent Amorphous Porous Silicon, Methods Of Making Colloidal Photoluminescent Amorphous Porous Silicon, And Methods Of Using Colloidal Photoluminescent Amorphous Porous Silicon

    KAUST Repository

    Chaieb, Sahraoui

    2015-04-09

    Embodiments of the present disclosure provide for a colloidal photoluminescent amorphous porous silicon particle suspension, methods of making a colloidal photoluminescent amorphous porous silicon particle suspension, methods of using a colloidal photoluminescent amorphous porous silicon particle suspension, and the like.

  1. Bipolar redox behaviour, field-effect mobility and transistor switching of the low-molecular azo glass AZOPD.

    Science.gov (United States)

    Arlt, Michael; Scheffler, Ayna; Suske, Irina; Eschner, Michael; Saragi, Tobat P I; Salbeck, Josef; Fuhrmann-Lieker, Thomas

    2010-11-07

    We present electrochemical and spectroelectrochemical data for the bipolar azo compound N,N'-diphenyl-N,N'-bis[4-(phenylazo)phenyl]-4,4'diaminobiphenyl (AZOPD) demonstrating reversible bipolar redox behaviour with a bandgap of 2.1 eV. The reduced species formed upon two-electron transfer can be described as bis(radical anion) as was confirmed by comparison with a reference compound with only one azo chromophore. Hole and electron transport behaviour in amorphous films was demonstrated by the fabrication of organic field-effect transistors using gold and magnesium contacts, respectively. The transistors are sensitive to light due to E-Z photoisomerization.

  2. Direct coupled amplifiers using field effect transistors

    International Nuclear Information System (INIS)

    Fowler, E.P.

    1964-03-01

    The concept of the uni-polar field effect transistor (P.E.T.) was known before the invention of the bi-polar transistor but it is only recently that they have been made commercially. Being produced as yet only in small quantities, their price imposes a restriction on use to circuits where their peculiar properties can be exploited to the full. One such application is described here where the combination of low voltage drift and relatively low input leakage current are necessarily used together. One of the instruments used to control nuclear reactors has a logarithmic response to the mean output current from a polarised ionisation chamber. The logarithmic signal is then differentiated electrically, the result being displayed on a meter calibrated to show the reactor divergence or doubling time. If displayed in doubling time the scale is calibrated reciprocally. Because of the wide range obtained in the logarithmic section and the limited supply voltage, an output of 1 volt per decade change in ionisation current is used. Differentiating this gives a current of 1.5 x 10 -8 A for p.s.D. (20 sec. doubling time) in the differentiating amplifier. To overcome some of the problems of noise due to statistical variations in input current, the circuit design necessitates a resistive path to ground at the amplifier input of 20 M.ohms. A schematic diagram is shown. 1. It is evident that a zero drift of 1% can be caused by a leakage current of 1.5 x 10 -10 A or an offset voltage of 3 mV at the amplifier input. Although the presently used electrometer valve is satisfactory from the point of view of grid current, there have been sudden changes in grid to grid voltage (the valve is a double triode) of up to 10 m.V. It has been found that a pair of F.E.T's. can be used to replace the electrometer valve so long as care is taken in correct balance of the two devices. An investigation has been made into the characteristics of some fourteen devices to see whether those with very

  3. Hydrogen in disordered and amorphous solids

    International Nuclear Information System (INIS)

    Bambakidis, G; Bowman, R.C.

    1986-01-01

    This book presents information on the following topoics: elements of the theory of amorphous semiconductors; electronic structure of alpha-SiH; fluctuation induced gap states in amorphous hydrogenated silicon; hydrogen on semiconductor surfaces; the influence of hydrogen on the defects and instabilities in hydrogenated amorphous silicon; deuteron magnetic resonance in some amorphous semiconductors; formation of amorphous metals by solid state reactions of hydrogen with an intermetallic compound; NMR studies of the hydrides of disordered and amorphous alloys; neutron vibrational spectroscopy of disordered metal-hydrogen system; dynamical disorder of hydrogen in LaNi /SUB 5-y/ M /SUB y/ hydrides studied by quasi-elastic neutron scattering; recent studies of intermetallic hydrides; tritium in Pd and Pd /SUB 0.80/ Sg /SUB 0.20/ ; and determination of hydrogen concentration in thin films of absorbing materials

  4. Molecular Dynamics, Recrystallization Behavior, and Water Solubility of the Amorphous Anticancer Agent Bicalutamide and Its Polyvinylpyrrolidone Mixtures.

    Science.gov (United States)

    Szczurek, Justyna; Rams-Baron, Marzena; Knapik-Kowalczuk, Justyna; Antosik, Agata; Szafraniec, Joanna; Jamróz, Witold; Dulski, Mateusz; Jachowicz, Renata; Paluch, Marian

    2017-04-03

    In this paper, we investigated the molecular mobility and physical stability of amorphous bicalutamide, a poorly water-soluble drug widely used in prostate cancer treatment. Our broadband dielectric spectroscopy measurements and differential scanning calorimetry studies revealed that amorphous BIC is a moderately fragile material with a strong tendency to recrystallize from the amorphous state. However, mixing the drug with polymer polyvinylpyrrolidone results in a substantial improvement of physical stability attributed to the antiplasticizing effect governed by the polymer additive. Furthermore, IR study demonstrated the existence of specific interactions between the drug and excipient. We found out that preparation of bicalutamide-polyvinylpyrrolidone mixture in a 2-1 weight ratio completely hinder material recrystallization. Moreover, we determined the time-scale of structural relaxation in the glassy state for investigated materials. Because molecular mobility is considered an important factor governing crystallization behavior, such information was used to approximate the long-term physical stability of an amorphous drug and drug-polymer systems upon their storage at room temperature. Moreover, we found that such systems have distinctly higher water solubility and dissolution rate in comparison to the pure amorphous form, indicating the genuine formulation potential of the proposed approach.

  5. The physics and applications of amorphous semiconductors

    CERN Document Server

    Madan, Arun

    1988-01-01

    This comprehensive, detailed treatise on the physics and applications of the new emerging technology of amorphous semiconductors focuses on specific device research problems such as the optimization of device performance. The first part of the book presents hydrogenated amorphous silicon type alloys, whose applications include inexpensive solar cells, thin film transistors, image scanners, electrophotography, optical recording and gas sensors. The second part of the book discusses amorphous chalcogenides, whose applications include electrophotography, switching, and memory elements. This boo

  6. Polyamorphous transition in amorphous fullerites C70

    International Nuclear Information System (INIS)

    Borisova, P. A.; Agafonov, S. S.; Glazkov, V. P.; D’yakonova, N. P.; Somenkov, V. A.

    2011-01-01

    Samples of amorphous fullerites C 70 have been obtained by mechanical activation (grinding in a ball mill). The structure of the samples has been investigated by neutron and X-ray diffraction. The high-temperature (up to 1200°C) annealing of amorphous fullerites revealed a polyamorphous transition from molecular to atomic glass, which is accompanied by the disappearance of fullerene halos at small scattering angles. Possible structural versions of the high-temperature amorphous phase are discussed.

  7. High resolution NMR spectroscopy of synthetic polymers in bulk

    International Nuclear Information System (INIS)

    Komorski, R.A.

    1986-01-01

    The contents of this book are: Overview of high-resolution NMR of solid polymers; High-resolution NMR of glassy amorphous polymers; Carbon-13 solid-state NMR of semicrystalline polymers; Conformational analysis of polymers of solid-state NMR; High-resolution NMR studies of oriented polymers; High-resolution solid-state NMR of protons in polymers; and Deuterium NMR of solid polymers. This work brings together the various approaches for high-resolution NMR studies of bulk polymers into one volume. Heavy emphasis is, of course, given to 13C NMR studies both above and below Tg. Standard high-power pulse and wide-line techniques are not covered

  8. Magnetic Field Effect in Conjugated Molecules-Based Devices

    Science.gov (United States)

    2017-10-23

    AFRL-AFOSR-JP-TR-2017-0073 Magnetic field effect in conjugated molecules-based devices Tzung-Fang Guo NATIONAL CHENG KUNG UNIVERSITY Final Report 10...Final 3. DATES COVERED (From - To) 22 Jul 2014 to 21 Jul 2017 4. TITLE AND SUBTITLE Magnetic field effect in conjugated molecules-based devices 5a... Magnetic field effect in conjugated molecule-based devices. The final year of the project had a collaboration with Professor Bin Hu at the University

  9. Amorphous silicon based radiation detectors

    International Nuclear Information System (INIS)

    Perez-Mendez, V.; Cho, G.; Drewery, J.; Jing, T.; Kaplan, S.N.; Qureshi, S.; Wildermuth, D.; Fujieda, I.; Street, R.A.

    1991-07-01

    We describe the characteristics of thin(1 μm) and thick (>30μm) hydrogenated amorphous silicon p-i-n diodes which are optimized for detecting and recording the spatial distribution of charged particles, x-rays and γ rays. For x-ray, γ ray, and charged particle detection we can use thin p-i-n photosensitive diode arrays coupled to evaporated layers of suitable scintillators. For direct detection of charged particles with high resistance to radiation damage, we use the thick p-i-n diode arrays. 13 refs., 7 figs

  10. Field-effect detection using phospholipid membranes -Topical Review

    Directory of Open Access Journals (Sweden)

    Chiho Kataoka-Hamai and Yuji Miyahara

    2010-01-01

    Full Text Available The application of field-effect devices to biosensors has become an area of intense research interest. An attractive feature of field-effect sensing is that the binding or reaction of biomolecules can be directly detected from a change in electrical signals. The integration of such field-effect devices into cell membrane mimics may lead to the development of biosensors useful in clinical and biotechnological applications. This review summarizes recent studies on the fabrication and characterization of field-effect devices incorporating model membranes. The incorporation of black lipid membranes and supported lipid monolayers and bilayers into semiconductor devices is described.

  11. Polymers under mechanical stress- an NMR investigation

    Energy Technology Data Exchange (ETDEWEB)

    Boehme, Ute; Scheler, Ulrich [Leibniz Institute of Polymer Research Dresden (Germany); Xu, Bo; Leisen, Johannes; Beckham, Haskell W. [Georgia Institute of Technology, Atlanta, Georgia (United States)

    2010-07-01

    Low-field NMR using permanent magnets in Halbach arrangements permit NMR investigation without the limits present in high-field NMR. The lower field in conjunction with confined stray field permit the application of NMR, in particular relaxation NMR in a stretching apparatus and a rheometer. Crystalline and amorphous fraction of semi-crystalline polymers are distinguished by their transverse relaxation times. Upon mechanical load the relaxation times of the amorphous fraction changes as seen in in-situ measurements on polypropylene rods. During the formation of a neck the crystalline fraction becomes more prominent.

  12. Detailed stability investigation of amorphous solid dispersions prepared by single-needle and high speed electrospinning.

    Science.gov (United States)

    Démuth, B; Farkas, A; Pataki, H; Balogh, A; Szabó, B; Borbás, E; Sóti, P L; Vigh, T; Kiserdei, É; Farkas, B; Mensch, J; Verreck, G; Van Assche, I; Marosi, G; Nagy, Z K

    2016-02-10

    In this research the long-term stability (one year) of amorphous solid dispersions (ASDs) prepared by high speed electrospinning was investigated at 25 °C/60% relative humidity (RH) (closed conditions) and 40 °C/75% RH (open conditions). Single needle electrospinning and film casting were applied as reference technologies. Itraconazole (ITR) was used as the model API in 40% concentration and the ASDs consisted of either one of the following polymers as a comparison: polyvinylpyrrolidone-vinyl acetate 6:4 copolymer (no hydrogen bonds between API and polymer) and hydroxypropyl methylcellulose (possible hydrogen bonds between oxo or tertiary nitrogen function of API and hydroxyl moiety of polymer). DSC, XRPD and dissolution characteristics of samples at 0, 3 and 12 months were investigated. In addition, Raman maps of certain electrospun ASDs were assessed to investigate crystallinity. A new chemometric method, based on Multivariate Curve Resolution-Alternating Least Squares algorithm, was developed to calculate the spectrum of amorphous ITR in the matrices and to determine the crystalline/amorphous ratio of aged samples. As it was expected ITR in single needle electrospun SDs was totally amorphous at the beginning, in addition hydroxypropyl methylcellulose could keep ITR in this form at 40 °C/75% RH up to one year due to the hydrogen bonds and high glass transition temperature of the SD. In polyvinylpyrrolidone-vinyl acetate matrix ITR remained amorphous at 25 °C/60% RH throughout one year. Materials prepared by scaled-up, high throughput version of electrospinning, which is compatible with pharmaceutical industry, also gained the same quality. Therefore these ASDs are industrially applicable and with an appropriate downstream process it would be possible to bring them to the market. Copyright © 2015 Elsevier B.V. All rights reserved.

  13. High Performance Ambipolar Diketopyrrolopyrrole-Thieno[3,2-b]thiophene Copolymer Field-Effect Transistors with Balanced Hole and Electron Mobilities

    DEFF Research Database (Denmark)

    Chen, Zhuoying; Lee, Mi Jung; Ashraf, Raja Shahid

    2012-01-01

    Ambipolar OFETs with balanced hole and electron field-effect mobilities both exceeding 1 cm2 V−1 s−1 are achieved based on a single-solution-processed conjugated polymer, DPPT-TT, upon careful optimization of the device architecture, charge injection, and polymer processing. Such high-performance......Ambipolar OFETs with balanced hole and electron field-effect mobilities both exceeding 1 cm2 V−1 s−1 are achieved based on a single-solution-processed conjugated polymer, DPPT-TT, upon careful optimization of the device architecture, charge injection, and polymer processing. Such high......-performance OFETs are promising for applications in ambipolar devices and integrated circuits, as well as model systems for fundamental studies....

  14. Multifunctional Self-Assembled Monolayers for Organic Field-Effect Transistors

    Science.gov (United States)

    Cernetic, Nathan

    Organic field effect transistors (OFETs) have the potential to reach commercialization for a wide variety of applications such as active matrix display circuitry, chemical and biological sensing, radio-frequency identification devices and flexible electronics. In order to be commercially competitive with already at-market amorphous silicon devices, OFETs need to approach similar performance levels. Significant progress has been made in developing high performance organic semiconductors and dielectric materials. Additionally, a common route to improve the performance metric of OFETs is via interface modification at the critical dielectric/semiconductor and electrode/semiconductor interface which often play a significant role in charge transport properties. These metal oxide interfaces are typically modified with rationally designed multifunctional self-assembled monolayers. As means toward improving the performance metrics of OFETs, rationally designed multifunctional self-assembled monolayers are used to explore the relationship between surface energy, SAM order, and SAM dipole on OFET performance. The studies presented within are (1) development of a multifunctional SAM capable of simultaneously modifying dielectric and metal surface while maintaining compatibility with solution processed techniques (2) exploration of the relationship between SAM dipole and anchor group on graphene transistors, and (3) development of self-assembled monolayer field-effect transistor in which the traditional thick organic semiconductor is replaced by a rationally designed self-assembled monolayer semiconductor. The findings presented within represent advancement in the understanding of the influence of self-assembled monolayers on OFETs as well as progress towards rationally designed monolayer transistors.

  15. Chemical vapor deposition grown monolayer graphene field-effect transistors with reduced impurity concentration

    Science.gov (United States)

    Ha, Tae-Jun; Lee, Alvin

    2015-07-01

    We report on the restoration of the electronic characteristics of waferscale chemical vapor deposition (CVD) monolayer graphene field-effect transistors (GFETs) by reducing the impurity concentration. An optimized electropolishing process on copper foils combined with carbon-fluorine encapsulation using a suitable amorphous fluoropolymer enables reducing the surface roughness of graphene and screening out interfacial impurity scattering, which leads to an improvement in all key device metrics. The conductivity at the Dirac point is substantially reduced, resulting in an increase in the on-off current ratio. In addition, the field-effect mobility increased from 1817 to 3918 cm2/V-s, the impurity concentration decreased from 1.1 × 1012 to 2.1 × 1011 cm-2 and the electron and hole transport became more symmetric. Significantly, favorable shifts toward zero voltage were observed in the Dirac point. We postulate that the smoother surface due to electropolishing and a pool of strong dipole-dipole moments in the flouropolymer coating provide a charge buffer that relaxes the fluctuation in the electron-hole puddles. We also investigate the long-term stability in GFETs encapsulated with fluoropolymer, which exhibit a high hydrophobicity that suppresses the chemical interaction with water molecules. [Figure not available: see fulltext.

  16. Studies of hydrogenated amorphous silicon

    Energy Technology Data Exchange (ETDEWEB)

    Bishop, S G; Carlos, W E

    1984-07-01

    This report discusses the results of probing the defect structure and bonding of hydrogenated amorphous silicon films using both nuclear magnetic resonance (NMR) and electron spin resonance (ESR). The doping efficiency of boron in a-Si:H was found to be less than 1%, with 90% of the boron in a threefold coordinated state. On the other hand, phosphorus NMR chemical shift measurements yielded a ration of threefold to fourfold P sites of roughly 4 to 1. Various resonance lines were observed in heavily boron- and phosphorus-doped films and a-SiC:H alloys. These lines were attributed to band tail states on twofold coordinated silicon. In a-SiC:H films, a strong resonance was attributed to dangling bonds on carbon atoms. ESR measurements on low-pressure chemical-vapor-deposited (LPCVD) a-Si:H were performed on samples. The defect density in the bulk of the films was 10/sup 17//cc with a factor of 3 increase at the surface of the sample. The ESR spectrum of LPCVD-prepared films was not affected by prolonged exposure to strong light. Microcrystalline silicon samples were also examined. The phosphorus-doped films showed a strong signal from the crystalline material and no resonance from the amorphous matrix. This shows that phosphorus is incorporated in the crystals and is active as a dopant. No signal was recorded from the boron-doped films.

  17. PHOTOREFRACTIVE POLYMERS

    NARCIS (Netherlands)

    Morichere, D; Malliaras, G.G; Krasnikov, V.V.; Bolink, H.J; Hadziioannou, G

    The use of polymers as photorefractive materials offers many advantages : flexibility in synthesis, doping, processing and low cost. The required functionalities responsible for photorefractivity, namely charge generation, transport, trapping and linear electrooptic effect are given in the polymer

  18. Amorphous graphite/polymethyl methacrylate composite microspheres: design, preparation, and performance study

    Science.gov (United States)

    Zhou, Sen; Yan, Chunjie; Liu, Chen; Jing, Luru; Liang, Tian

    2017-05-01

    Amorphous graphite/polymethyl methacrylate (MAG/PMMA) composite microspheres were synthesized by suspension polymerization. It was found that the contact angle of amorphous graphite (AG) changed from 32.55° into 112.58° after modification by sodium(C16) alkylsulfonate, which showed that the surface of modified amorphous graphite (MAG) were hydrophobic. The modified AGs effectively improved the dispersion in monomer, which helped to improve the compatibility of amorphous graphite in the polymer. The experimental results showed that the thermal properties of the composites were improved effectively by increasing the loading amounts of MAGs, especially when the amount was 2.5 wt %. The compressive strength of MAG/PMMA composite microspheres with the same diameter (1 mm or 2 mm) was significantly 2 times higher than that of the pure PMMA crosslinked polymer microspheres. The specific surface area increased from 0.2347 m2·g-1 of pure PMMA to 3.4074 m2·g-1 when the amount of adding MAGs was 2.0 wt %. The N2 adsorption-desorption isotherms of pure PMMA and MAG/PMMA composite microspheres belonged to V type of IUPAC and H1 hysteresis loop, indicating that adsorption quantities were higher than that of PMMA with adding the MAGs.

  19. Importance of in vitro dissolution conditions for the in vivo predictability of an amorphous solid dispersion containing a pH-sensitive carrier

    DEFF Research Database (Denmark)

    Wendelboe, Johan; Knopp, Matthias Manne; Khan, Fauzan

    2017-01-01

    The present study investigated the influence of in vitro dissolution conditions on the in vivo predictability of an amorphous solid dispersion of celecoxib (CCX) in the pH-sensitive polymer Eudragit(®) S 100. Different doses of a 25:75w/w% CCX:Eudragit(®) S 100 amorphous solid dispersion (CCX...... performance of amorphous solid dispersions with pH-sensitive polymers, it is imperative that the in vitro dissolution conditions are carefully considered.......:EUD) were investigated. During in vitro dissolution a significant effect of the pH of the dissolution media on the release of CCX was observed. In fasted state simulated intestinal fluid (FaSSIF) pH 6.5, the release of CCX from the amorphous solid dispersion was comparable to that of crystalline CCX...

  20. Dissolution performance of binary amorphous drug combinations--Impact of a second drug on the maximum achievable supersaturation.

    Science.gov (United States)

    Trasi, Niraj S; Taylor, Lynne S

    2015-12-30

    An increased number of amorphous formulations of poorly water soluble drugs are being introduced into the market due to their higher transient solubility and thus faster absorption and higher bioavailability. While most amorphous drug products contain a single drug substance, there is a growing trend towards co-formulating compounds in the same dosage form to improve patient compliance. The purpose of the present work was to evaluate the dissolution behavior and maximum achievable solution concentrations of amorphous solid dispersions of co-formulated ritonavir and lopinavir, and to compare the results with individual amorphous solid dispersion formulations. Dispersions of ritonavir and lopinavir were prepared in polyvinylpyrrolidone (PVP) or hydroxypropylmethylcellulose acetate succinate (HPMCAS) at a 20% (w/w) total drug loading, both alone and in combination, at three different lopinavir:ritonavir weight ratios. Amorphous films containing both drugs, but no polymer, were also prepared. The dissolution behavior of the dispersions and the amorphous films in non-sink conditions was evaluated, using ultracentrifugation to separate any colloidal material from molecularly dissolved drug. Nanoparticle tracking analysis was used to characterize colloidal material formed during the dissolution process. Results from the dissolution study revealed that, although supersaturated solutions resulted following dissolution, the maximum achievable concentration of each drug, when present in combination, was dramatically lower than when the individual dispersions were dissolved. The maximum achievable solution concentration for systems containing both drugs was found to decrease as the mole fraction of the drug in the amorphous phase decreased. The type of polymer used to formulate the dispersion also appeared to influence the dissolution behavior whereby the HPMCAS dispersions dissolved rapidly, resulting in the generation of a nanodroplets, while the PVP dispersions did not

  1. Polymer Nanocomposites

    Indian Academy of Sciences (India)

    polymer nanocompo- sites are used as advanced toner materials for high quality colour copiers and printers and as contrast agents in NMR analysis, memory devices. .... tions on polymer nanocomposite can thus pay rich dividends. Suggested Reading. [1] Metal-Polymer Nanocomposites Nicolais, Luigi(ed.) ; Carotenuto,.

  2. Light-emitting ambipolar organic heterostructure field-effect transistor

    NARCIS (Netherlands)

    Rost, Constance; Karg, Siegfried; Riess, Walter; Loi, Maria Antonietta; Murgia, Mauro; Muccini, Michele

    2004-01-01

    We have investigated ambipolar charge injection and transport in organic field-effect transistors (OFETs) as prerequisites for a light-emitting organic field-effect transistor (LEOFET). OFETs containing a single material as active layer generally function either as a p- or an n-channel device.

  3. Low dielectric constant-based organic field-effect transistors and metal-insulator-semiconductor capacitors

    Science.gov (United States)

    Ukah, Ndubuisi Benjamin

    This thesis describes a study of PFB and pentacene-based organic field-effect transistors (OFET) and metal-insulator-semiconductor (MIS) capacitors with low dielectric constant (k) poly(methyl methacrylate) (PMMA), poly(4-vinyl phenol) (PVP) and cross-linked PVP (c-PVP) gate dielectrics. A physical method -- matrix assisted pulsed laser evaporation (MAPLE) -- of fabricating all-polymer field-effect transistors and MIS capacitors that circumvents inherent polymer dissolution and solvent-selectivity problems, is demonstrated. Pentacene-based OFETs incorporating PMMA and PVP gate dielectrics usually have high operating voltages related to the thickness of the dielectric layer. Reduced PMMA layer thickness (≤ 70 nm) was obtained by dissolving the PMMA in propylene carbonate (PC). The resulting pentacene-based transistors exhibited very low operating voltage (below -3 V), minimal hysteresis in their transfer characteristics, and decent electrical performance. Also low voltage (within -2 V) operation using thin (≤ 80 nm) low-k and hydrophilic PVP and c-PVP dielectric layers obtained via dissolution in high dipole moment and high-k solvents -- PC and dimethyl sulfoxide (DMSO), is demonstrated to be a robust means of achieving improved electrical characteristics and high operational stability in OFETs incorporating PVP and c-PVP dielectrics.

  4. Structural morphology of amorphous conducting carbon film

    Indian Academy of Sciences (India)

    Unknown

    in nanotubes and sp3 rich amorphous carbons for their application in field emission, device application, etc in- vestigations on sp2 rich amorphous carbon forms are very few. Though DLC films have potential application in field emission (FE) due to their low threshold voltage, the carbon centres, which are believed to play ...

  5. Towards upconversion for amorphous silicon solar cells

    NARCIS (Netherlands)

    de Wild, J.; Meijerink, A.; Rath, J.K.; van Sark, W.G.J.H.M.; Schropp, R.E.I.

    2010-01-01

    Upconversion of subbandgap light of thin film single junction amorphous silicon solar cells may enhance their performance in the near infrared (NIR). In this paper we report on the application of the NIR–vis upconverter β-NaYF4:Yb3+(18%) Er3+(2%) at the back of an amorphous silicon solar cell in

  6. Film adhesion in amorphous silicon solar cells

    Indian Academy of Sciences (India)

    TECS

    flexible triple junction, amorphous silicon solar cells. At the Malaysia Energy Centre (MEC), we fabricated triple junction amorphous silicon solar cells (up to 12⋅7% efficiency (Wang et al 2002)) and laser-interconnected modules on steel, glass and polyimide substrates. A major issue encountered is the adhesion of thin film ...

  7. Colors and the evolution of amorphous galaxies

    International Nuclear Information System (INIS)

    Gallagher, J.S. III; Hunter, D.A.

    1987-01-01

    UBVRI and H-alpha photometric observations are presented for 16 amorphous galaxies and a comparison sample of Magellanic irregular (Im) and Sc spiral galaxies. These data are analyzed in terms of star-formation rates and histories in amorphous galaxies. Amorphous galaxies have mean global colors and star-formation rates per unit area that are similar to those in giant Im systems, despite differences in spatial distributions of star-forming centers in these two galactic structural classes. Amorphous galaxies differ from giant Im systems in having somewhat wider scatter in relationships between B - V and U - B colors, and between U - B and L(H-alpha)/L(B). This scatter is interpreted as resulting from rapid variations in star-formation rates during the recent past, which could be a natural consequence of the concentration of star-forming activity into centrally located, supergiant young stellar complexes in many amorphous galaxies. While the unusual spatial distribution and intensity of star formation in some amorphous galaxies is due to interactions with other galaxies, several amorphous galaxies are relatively isolated and thus the processes must be internal. The ultimate evolutionary fate of rapidly evolving amorphous galaxies remains unknown. 77 references

  8. Amorphization of ice under mechanical stresses

    Science.gov (United States)

    Bordonskii, G. S.; Krylov, S. D.

    2017-11-01

    The dielectric parameters of freshly produced freshwater ice in the microwave range are investigated. It is established that this kind of ice contains a noticeable amount of amorphous ice. Its production is associated with plastic deformation under mechanical stresses. An assessment of the dielectric-permeability change caused by amorphous ice in the state of a slowly flowing medium is given.

  9. Electron beam recrystallization of amorphous semiconductor materials

    Science.gov (United States)

    Evans, J. C., Jr.

    1968-01-01

    Nucleation and growth of crystalline films of silicon, germanium, and cadmium sulfide on substrates of plastic and glass were investigated. Amorphous films of germanium, silicon, and cadmium sulfide on amorphous substrates of glass and plastic were converted to the crystalline condition by electron bombardment.

  10. Photoexcitation-induced processes in amorphous semiconductors

    International Nuclear Information System (INIS)

    Singh, Jai

    2005-01-01

    Theories for the mechanism of photo-induced processes of photodarkening (PD), volume expansion (VE) in amorphous chalcogenides are presented. Rates of spontaneous emission of photons by radiative recombination of excitons in amorphous semiconductors are also calculated and applied to study the excitonic photoluminescence in a-Si:H. Results are compared with previous theories

  11. Analytical theory of noncollinear amorphous metallic magnetism

    International Nuclear Information System (INIS)

    Kakehashi, Y.; Uchida, T.

    2001-01-01

    Analytical theory of noncollinear magnetism in amorphous metals is proposed on the basis of the Gaussian model for the distribution of the interatomic distance and the saddle-point approximation. The theory removes the numerical difficulty in the previous theory based on the Monte-Carlo sampling method, and reasonably describes the magnetic properties of amorphous transition metals

  12. Precipitation of lamellar gold nanocrystals in molten polymers

    Science.gov (United States)

    Palomba, M.; Carotenuto, G.

    2016-05-01

    Non-aggregated lamellar gold crystals with regular shape (triangles, squares, pentagons, etc.) have been produced by thermal decomposition of gold chloride (AuCl) molecules in molten amorphous polymers (polystyrene and poly(methyl methacrylate)). Such covalent inorganic gold salt is high soluble into non-polar polymers and it thermally decomposes at temperatures compatible with the polymer thermal stability, producing gold atoms and chlorine radicals. At the end of the gold precipitation process, the polymer matrix resulted chemically modified because of the partial cross-linking process due to the gold atom formation reaction.

  13. Screening methodologies for the development of spray-dried amorphous solid dispersions.

    Science.gov (United States)

    Duarte, Íris; Santos, José Luís; Pinto, João F; Temtem, Márcio

    2015-01-01

    To present a new screening methodology intended to be used in the early development of spray-dried amorphous solid dispersions. A model that combines thermodynamic, kinetic and manufacturing considerations was implemented to obtain estimates of the miscibility and phase behavior of different itraconazole-based solid dispersions. Additionally, a small-scale solvent casting protocol was developed to enable a fast assessment on the amorphous stability of the different drug-polymer systems. Then, solid dispersions at predefined drug loads were produced in a lab-scale spray dryer for powder characterization and comparison of the results generated by the model and solvent cast samples. The results obtained with the model enabled the ranking of the polymers from a miscibility standpoint. Such ranking was consistent with the experimental data obtained by solvent casting and spray drying. Moreover, the range of optimal drug load determined by the model was as well consistent with the experimental results. The screening methodology presented in this work showed that a set of amorphous formulation candidates can be assessed in a computer model, enabling not only the determination of the most suitable polymers, but also of the optimal drug load range to be tested in laboratory experiments. The set of formulation candidates can then be further fine-tuned with solvent casting experiments using a small amount of API, which will then provide the decision for the final candidate formulations to be assessed in spray drying experiments.

  14. Solid-state diffusion in amorphous zirconolite

    Energy Technology Data Exchange (ETDEWEB)

    Yang, C.; Dove, M. T.; Trachenko, K. [School of Physics and Astronomy, Queen Mary University of London, Mile End Road, London E1 4NS (United Kingdom); Zarkadoula, E. [School of Physics and Astronomy, Queen Mary University of London, Mile End Road, London E1 4NS (United Kingdom); Materials Science and Technology Division, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831-6138 (United States); Todorov, I. T. [STFC Daresbury Laboratory, Warrington WA4 1EP (United Kingdom); Geisler, T. [Steinmann-Institut für Geologie, Mineralogie und Paläontologie, University of Bonn, D-53115 Bonn (Germany); Brazhkin, V. V. [Institute for High Pressure Physics, RAS, 142190 Moscow (Russian Federation)

    2014-11-14

    We discuss how structural disorder and amorphization affect solid-state diffusion, and consider zirconolite as a currently important case study. By performing extensive molecular dynamics simulations, we disentangle the effects of amorphization and density, and show that a profound increase of solid-state diffusion takes place as a result of amorphization. Importantly, this can take place at the same density as in the crystal, representing an interesting general insight regarding solid-state diffusion. We find that decreasing the density in the amorphous system increases pre-factors of diffusion constants, but does not change the activation energy in the density range considered. We also find that atomic species in zirconolite are affected differently by amorphization and density change. Our microscopic insights are relevant for understanding how solid-state diffusion changes due to disorder and for building predictive models of operation of materials to be used to encapsulate nuclear waste.

  15. Elemental distribution in fluorinated amorphous carbon thin films.

    Science.gov (United States)

    Lamperti, A; Bottani, C E; Ossi, P M

    2005-01-01

    Focused ion beam-secondary ion mass spectrometry (FIB-SIMS) with 20 nm spatial resolution has been used to analyze amorphous fluorinated carbon thin films, deposited by plasma assisted chemical vapor deposition (PACVD), at micro- to nano-scale. Mass spectra and ion imaging of film surface were acquired and the presence and distribution of contaminants were investigated. Surface images show the secondary ion distribution for F(-), CH(-), CF(-). A change in size and topology of fluorine-rich areas is correlated with film hardness and with microstructure transition from diamond-like to polymer-like, as indicated by infrared and Raman spectroscopies. Based on the surface distributions of CF(-) and CH(-) and on the vibrational spectroscopy results, a mechanism of fluorine substitution for hydrogen and an attempt to explain the film structure and microstructure is proposed.

  16. Systematic study of amorphous hydrogenated and fluorinated carbon films

    Science.gov (United States)

    Lamperti, A.; Ossi, P. M.

    2003-01-01

    Amorphous fluorinated carbon films were grown from CF 4 and C 2H 2 mixtures, using a Plasma Assisted Chemical Vapour Deposition (PACVD) apparatus. Two sets of films were deposited, changing in a systematic way the CF 4 flux and the bias voltage ( Vb). Film composition and structure were analysed by secondary ion mass spectroscopy (SIMS), infrared (IR) and Raman spectroscopies. Film hardness was obtained by micro-indentation measurements. On increasing fluorine content in films, hardness decreases and a fluorescence background in Raman spectra appears at high fluorine content, showing a diamond- to polymer-like structural transition. Infrared spectra indicate the presence of CF x, CCHF and CCF 2 groups in the films. Our data are compared with previous results in the literature and the mechanisms involved in film formation are discussed, especially regarding fluorine substitution for hydrogen.

  17. Hydrogen Bonding Interactions in Amorphous Indomethacin and Its Amorphous Solid Dispersions with Poly(vinylpyrrolidone) and Poly(vinylpyrrolidone-co-vinyl acetate) Studied Using (13)C Solid-State NMR.

    Science.gov (United States)

    Yuan, Xiaoda; Xiang, Tian-Xiang; Anderson, Bradley D; Munson, Eric J

    2015-12-07

    Hydrogen bonding interactions in amorphous indomethacin and amorphous solid dispersions of indomethacin with poly(vinylpyrrolidone), or PVP, and poly(vinylpyrrolidone-co-vinyl acetate), or PVP/VA, were investigated quantitatively using solid-state NMR spectroscopy. Indomethacin that was (13)C isotopically labeled at the carboxylic acid carbon was used to selectively analyze the carbonyl region of the spectrum. Deconvolution of the carboxylic acid carbon peak revealed that 59% of amorphous indomethacin molecules were hydrogen bonded through carboxylic acid cyclic dimers, 15% were in disordered carboxylic acid chains, 19% were hydrogen bonded through carboxylic acid and amide interactions, and the remaining 7% were free of hydrogen bonds. The standard dimerization enthalpy and entropy of amorphous indomethacin were estimated to be -38 kJ/mol and -91 J/(mol · K), respectively, using polystyrene as the "solvent". Polymers such as PVP and PVP/VA disrupted indomethacin self-interactions and formed hydrogen bonds with the drug. The carboxylic acid dimers were almost completely disrupted with 50% (wt) of PVP or PVP/VA. The fraction of disordered carboxylic acid chains also decreased as the polymer content increased. The solid-state NMR results were compared with molecular dynamics (MD) simulations from the literature. The present work highlights the potential of (13)C solid-state NMR to detect and quantify various hydrogen bonded species in amorphous solid dispersions as well as to serve as an experimental validation of MD simulations.

  18. Characterization of the polymer energy landscape in polymer:fullerene bulk heterojunctions with pure and mixed phases

    KAUST Repository

    Sweetnam, Sean

    2014-10-08

    Theoretical and experimental studies suggest that energetic offsets between the charge transport energy levels in different morphological phases of polymer:fullerene bulk heterojunctions may improve charge separation and reduce recombination in polymer solar cells (PSCs). In this work, we use cyclic voltammetry, UV-vis absorption, and ultraviolet photoelectron spectroscopy to characterize hole energy levels in the polymer phases of polymer:fullerene bulk heterojunctions. We observe an energetic offset of up to 150 meV between amorphous and crystalline polymer due to bandgap widening associated primarily with changes in polymer conjugation length. We also observe an energetic offset of up to 350 meV associated with polymer:fullerene intermolecular interactions. The first effect has been widely observed, but the second effect is not always considered despite being larger in magnitude for some systems. These energy level shifts may play a major role in PSC performance and must be thoroughly characterized for a complete understanding of PSC function.

  19. Nobel Prize 2000: from conducting polymers to molecular electronics

    International Nuclear Information System (INIS)

    Pron, A.; Rannou, P.

    2001-01-01

    In this paper the development of conducting organic polymers is reviewed. Poly(3-alkylthiophenes) with regioregularity exceeding 99% are especially interesting because if used as a thin semiconducting layer in the field effect transistor (FET) configuration they become superconducting at 2.35 K. This is the first example of the superconductivity of an organic polymer. Fields of use of conducting polymers are reviewed, too

  20. Compositions for directed alignment of conjugated polymers

    Science.gov (United States)

    Kim, Jinsang; Kim, Bong-Gi; Jeong, Eun Jeong

    2016-04-19

    Conjugated polymers (CPs) achieve directed alignment along an applied flow field and a dichroic ratio of as high as 16.67 in emission from well-aligned thin films and fully realized anisotropic optoelectronic properties of CPs in field-effect transistor (FET).

  1. Influence of nickel(II) oxide nanoparticle addition on the performance of organic field effect transistors.

    Science.gov (United States)

    Park, Soohyeong; Nam, Sungho; Kim, Joonhyeon; Seo, Jooyeok; Jeong, Jaehoon; Woo, Sungho; Kim, Hwajeong; Kim, Youngkyoo

    2013-09-01

    Here, the improved performance of organic field effect transistors (OFET) by doping inorganic nanoparticles into a semiconducting polymer as a channel layer is briefly reported. Nickel(II) oxide nanoparticle (NiOnp) was used as an inorganic dopant while regioregular poly(3-hexylthiophene) (P3HT) was used as a matrix polymer for the channel layer in the OFETs. The doping ratio of NiOnp was made 1 wt.% so that it would minimally influence the nanostructure of the P3HT channel layer. The results showed that the optical absorption spectrum of the P3HT film was slightly red-shifted by the NiOnp doping, which reflects the improved crystallinity of the P3HT domains in the P3HT:NiOnp films. The drain current of the OFETs with the P3HT:NiOnp films was significantly enhanced ca. three-to-seven fold by the NiOnp doping under appying gate voltages while the hole mobility of the OFETs P3HT:NiOnp films was improved as much as three fold by the NiOnp doping. The enhanced performance has been assigned to the role of NiOnp that has relatively higher hole mobility than the P3HT polymer.

  2. Photonic crystals, amorphous materials, and quasicrystals.

    Science.gov (United States)

    Edagawa, Keiichi

    2014-06-01

    Photonic crystals consist of artificial periodic structures of dielectrics, which have attracted much attention because of their wide range of potential applications in the field of optics. We may also fabricate artificial amorphous or quasicrystalline structures of dielectrics, i.e. photonic amorphous materials or photonic quasicrystals. So far, both theoretical and experimental studies have been conducted to reveal the characteristic features of their optical properties, as compared with those of conventional photonic crystals. In this article, we review these studies and discuss various aspects of photonic amorphous materials and photonic quasicrystals, including photonic band gap formation, light propagation properties, and characteristic photonic states.

  3. Novel Organic Field Effect Transistors via Nano-Modification

    National Research Council Canada - National Science Library

    Wen, Ten-Chin; Chou, Wei-Yang; Guo, Tzung-Fang; Wang, Yeong-Her

    2005-01-01

    .... The performance of organic FETs is determined primarily by the field effect mobility of the carriers in the organic semiconductor layers and by the efficiency of injecting and extracting carriers...

  4. The Physics of Electric Field Effect Thermoelectric Devices

    OpenAIRE

    Sandomirsky, V.; Butenko, A. V.; Levin, R.; Schlesinger, Y.

    2001-01-01

    We describe here a novel approach to the subject of thermoelectric devices. The current best thermoelectrics are based on heavily doped semiconductors or semimetal alloys. We show that utilization of electric field effect or ferroelectric field effect, not only provides a new route to this problem, bypassing the drawbacks of conventional doping, but also offers significantly improved thermoelectric characteristics. We present here model calculation of the thermoelectric figure of merit in thi...

  5. Investigation of itraconazole ternary amorphous solid dispersions based on povidone and Carbopol.

    Science.gov (United States)

    Meng, Fan; Meckel, Jordan; Zhang, Feng

    2017-08-30

    We investigate a ternary system that consists of itraconazole (ITZ) and two polymers: povidone K12 and Carbopol 907. The interactions between these two polymers and their effects on the properties of ternary ITZ amorphous solid dispersions (ASDs) are studied. These two polymers can form a water-insoluble complex in acidic aqueous media. The critical pH is determined to be 4.17. The weight percentage of Carbopol 907 in the interpolymer complex range from 59 to 70%, depending on the initial ratios between these two polymers in the starting solutions. This complexation is driven by a negative enthalpy change from the H-bonding between the two polymers and a positive entropy change from the freed water molecules. Due to the slow precipitation of the interpolymer complex in aqueous media, the attempt to prepare ternary ASD using solvent-controlled coprecipitation is not successful. Melt extrusion is identified to be the only viable method to prepare this ternary ASD. We find that interpolymer complex-based ASDs are physically less stable and demonstrate the poorest drug-release properties when compared to individual polymer-based binary ASDs. This study illustrates that the too strong interaction between polymers in ternary ASDs is detrimental to their performance. Copyright © 2017 Elsevier B.V. All rights reserved.

  6. Polymer Chemistry

    Science.gov (United States)

    Williams, Martha; Roberson, Luke; Caraccio, Anne

    2010-01-01

    This viewgraph presentation describes new technologies in polymer and material chemistry that benefits NASA programs and missions. The topics include: 1) What are Polymers?; 2) History of Polymer Chemistry; 3) Composites/Materials Development at KSC; 4) Why Wiring; 5) Next Generation Wiring Materials; 6) Wire System Materials and Integration; 7) Self-Healing Wire Repair; 8) Smart Wiring Summary; 9) Fire and Polymers; 10) Aerogel Technology; 11) Aerogel Composites; 12) Aerogels for Oil Remediation; 13) KSC's Solution; 14) Chemochromic Hydrogen Sensors; 15) STS-130 and 131 Operations; 16) HyperPigment; 17) Antimicrobial Materials; 18) Conductive Inks Formulations for Multiple Applications; and 19) Testing and Processing Equipment.

  7. Star Polymers.

    Science.gov (United States)

    Ren, Jing M; McKenzie, Thomas G; Fu, Qiang; Wong, Edgar H H; Xu, Jiangtao; An, Zesheng; Shanmugam, Sivaprakash; Davis, Thomas P; Boyer, Cyrille; Qiao, Greg G

    2016-06-22

    Recent advances in controlled/living polymerization techniques and highly efficient coupling chemistries have enabled the facile synthesis of complex polymer architectures with controlled dimensions and functionality. As an example, star polymers consist of many linear polymers fused at a central point with a large number of chain end functionalities. Owing to this exclusive structure, star polymers exhibit some remarkable characteristics and properties unattainable by simple linear polymers. Hence, they constitute a unique class of technologically important nanomaterials that have been utilized or are currently under audition for many applications in life sciences and nanotechnologies. This article first provides a comprehensive summary of synthetic strategies towards star polymers, then reviews the latest developments in the synthesis and characterization methods of star macromolecules, and lastly outlines emerging applications and current commercial use of star-shaped polymers. The aim of this work is to promote star polymer research, generate new avenues of scientific investigation, and provide contemporary perspectives on chemical innovation that may expedite the commercialization of new star nanomaterials. We envision in the not-too-distant future star polymers will play an increasingly important role in materials science and nanotechnology in both academic and industrial settings.

  8. Polymer Electrolytes

    Science.gov (United States)

    Hallinan, Daniel T.; Balsara, Nitash P.

    2013-07-01

    This review article covers applications in which polymer electrolytes are used: lithium batteries, fuel cells, and water desalination. The ideas of electrochemical potential, salt activity, and ion transport are presented in the context of these applications. Potential is defined, and we show how a cell potential measurement can be used to ascertain salt activity. The transport parameters needed to fully specify a binary electrolyte (salt + solvent) are presented. We define five fundamentally different types of homogeneous electrolytes: type I (classical liquid electrolytes), type II (gel electrolytes), type III (dry polymer electrolytes), type IV (dry single-ion-conducting polymer electrolytes), and type V (solvated single-ion-conducting polymer electrolytes). Typical values of transport parameters are provided for all types of electrolytes. Comparison among the values provides insight into the transport mechanisms occurring in polymer electrolytes. It is desirable to decouple the mechanical properties of polymer electrolyte membranes from the ionic conductivity. One way to accomplish this is through the development of microphase-separated polymers, wherein one of the microphases conducts ions while the other enhances the mechanical rigidity of the heterogeneous polymer electrolyte. We cover all three types of conducting polymer electrolyte phases (types III, IV, and V). We present a simple framework that relates the transport parameters of heterogeneous electrolytes to homogeneous analogs. We conclude by discussing electrochemical stability of electrolytes and the effects of water contamination because of their relevance to applications such as lithium ion batteries.

  9. Pressure-induced reversible amorphization and an amorphous-amorphous transition in Ge₂Sb₂Te₅ phase-change memory material.

    Science.gov (United States)

    Sun, Zhimei; Zhou, Jian; Pan, Yuanchun; Song, Zhitang; Mao, Ho-Kwang; Ahuja, Rajeev

    2011-06-28

    Ge(2)Sb(2)Te(5) (GST) is a technologically very important phase-change material that is used in digital versatile disks-random access memory and is currently studied for the use in phase-change random access memory devices. This type of data storage is achieved by the fast reversible phase transition between amorphous and crystalline GST upon heat pulse. Here we report pressure-induced reversible crystalline-amorphous and polymorphic amorphous transitions in NaCl structured GST by ab initio molecular dynamics calculations. We have showed that the onset amorphization of GST starts at approximately 18 GPa and the system become completely random at approximately 22 GPa. This amorphous state has a cubic framework (c-amorphous) of sixfold coordinations. With further increasing pressure, the c-amorphous transforms to a high-density amorphous structure with trigonal framework (t-amorphous) and an average coordination number of eight. The pressure-induced amorphization is investigated to be due to large displacements of Te atoms for which weak Te-Te bonds exist or vacancies are nearby. Upon decompressing to ambient conditions, the original cubic crystalline structure is restored for c-amorphous, whereas t-amorphous transforms to another amorphous phase that is similar to the melt-quenched amorphous GST.

  10. Polymer chemistry (revised edition)

    International Nuclear Information System (INIS)

    Kim, Jae Mum

    1987-02-01

    This book deals with polymer chemistry, which is divided into fourteen chapters. The contents of this book are development of polymer chemistry, conception of polymer, measurement of polymer chemistry, conception of polymer, measurement of polymer, molecule structure of polymer, thermal prosperities of solid polymer, basic theory of polymerization, radical polymerization, ion polymerization, radical polymerization, copolymerization, polymerization by step-reaction, polymer reaction, crown polymer and inorganic polymer on classification and process of creation such as polymeric sulfur and carbon fiber.

  11. Corrosion resistant amorphous metals and methods of forming corrosion resistant amorphous metals

    Science.gov (United States)

    Farmer, Joseph C [Tracy, CA; Wong, Frank M. G. [Livermore, CA; Haslam, Jeffery J [Livermore, CA; Yang, Nancy [Lafayette, CA; Lavernia, Enrique J [Davis, CA; Blue, Craig A [Knoxville, TN; Graeve, Olivia A [Reno, NV; Bayles, Robert [Annandale, VA; Perepezko, John H [Madison, WI; Kaufman, Larry [Brookline, MA; Schoenung, Julie [Davis, CA; Ajdelsztajn, Leo [Walnut Creek, CA

    2009-11-17

    A system for coating a surface comprises providing a source of amorphous metal, providing ceramic particles, and applying the amorphous metal and the ceramic particles to the surface by a spray. The coating comprises a composite material made of amorphous metal that contains one or more of the following elements in the specified range of composition: yttrium (.gtoreq.1 atomic %), chromium (14 to 18 atomic %), molybdenum (.gtoreq.7 atomic %), tungsten (.gtoreq.1 atomic %), boron (.ltoreq.5 atomic %), or carbon (.gtoreq.4 atomic %).

  12. Surface magnetic structures in amorphous ferromagnetic microwires

    International Nuclear Information System (INIS)

    Usov, N.A.; Serebryakova, O.N.; Gudoshnikov, S.A.; Tarasov, V.P.

    2017-01-01

    The spatial period of magnetization perturbations that occur near the surface of magnetic nanotube or nanowire under the influence of surface magnetic anisotropy is determined by means of numerical simulation as a function of the sample geometry and material parameters. The surface magnetization distribution obtained is then used to estimate the period of the surface magnetic texture in amorphous microwire of several micrometers in diameter by means of appropriate variational procedure. The period of the surface magnetic texture in amorphous microwire is found to be significantly smaller than the wire diameter. - Highlights: • Magnetic structure may arise near the magnetic nanotube surface under the influence of surface magnetic anisotropy. • The period of the surface magnetization pattern is calculated as a function of the sample geometry. • Similar magnetic structure may exist in amorphous microwire of several micrometers in diameter. • The period of the surface magnetic structure in amorphous wire is found to be significantly smaller than the wire diameter.

  13. Bulk amorphous Mg-based alloys

    DEFF Research Database (Denmark)

    Pryds, Nini

    2004-01-01

    The present paper describes the preparation and properties of bulk amorphous quarternary Mg-based alloys and the influence of additional elements on the ability of the alloy to form bulk amorphous. The main goal is to find a Mg-based alloy system which shows both high strength to weight ratio...... and a low glass transition temperature. The alloys were prepared by using a relatively simple technique, i.e. rapid cooling of the melt in a copper wedge mould. The essential structural changes that are achieved by going from the amorphous to the crystalline state through the supercooled liquid state...... are discussed in this paper. On the basis of these measurements phase diagrams of the different systems were constructed. Finally, it is demonstrated that when pressing the bulk amorphous alloy onto a metallic dies at temperatures within the supercooled liquid region, the alloy faithfully replicates the surface...

  14. Surface magnetic structures in amorphous ferromagnetic microwires

    Energy Technology Data Exchange (ETDEWEB)

    Usov, N.A., E-mail: usov@obninsk.ru [National University of Science and Technology «MISIS», 119049 Moscow (Russian Federation); Pushkov Institute of Terrestrial Magnetism, Ionosphere and Radio Wave Propagation, Russian Academy of Sciences, IZMIRAN, 108840 Troitsk, Moscow (Russian Federation); Serebryakova, O.N.; Gudoshnikov, S.A. [National University of Science and Technology «MISIS», 119049 Moscow (Russian Federation); Pushkov Institute of Terrestrial Magnetism, Ionosphere and Radio Wave Propagation, Russian Academy of Sciences, IZMIRAN, 108840 Troitsk, Moscow (Russian Federation); Tarasov, V.P. [National University of Science and Technology «MISIS», 119049 Moscow (Russian Federation)

    2017-05-01

    The spatial period of magnetization perturbations that occur near the surface of magnetic nanotube or nanowire under the influence of surface magnetic anisotropy is determined by means of numerical simulation as a function of the sample geometry and material parameters. The surface magnetization distribution obtained is then used to estimate the period of the surface magnetic texture in amorphous microwire of several micrometers in diameter by means of appropriate variational procedure. The period of the surface magnetic texture in amorphous microwire is found to be significantly smaller than the wire diameter. - Highlights: • Magnetic structure may arise near the magnetic nanotube surface under the influence of surface magnetic anisotropy. • The period of the surface magnetization pattern is calculated as a function of the sample geometry. • Similar magnetic structure may exist in amorphous microwire of several micrometers in diameter. • The period of the surface magnetic structure in amorphous wire is found to be significantly smaller than the wire diameter.

  15. Amorphous Phases on the Surface of Mars

    Science.gov (United States)

    Rampe, E. B.; Morris, R. V.; Ruff, S. W.; Horgan, B.; Dehouck, E.; Achilles, C. N.; Ming, D. W.; Bish, D. L.; Chipera, S. J.

    2014-01-01

    Both primary (volcanic/impact glasses) and secondary (opal/silica, allophane, hisingerite, npOx, S-bearing) amorphous phases appear to be major components of martian surface materials based on orbital and in-situ measurements. A key observation is that whereas regional/global scale amorphous components include altered glass and npOx, local scale amorphous phases include hydrated silica/opal. This suggests widespread alteration at low water-to-rock ratios, perhaps due to snow/ice melt with variable pH, and localized alteration at high water-to-rock ratios. Orbital and in-situ measurements of the regional/global amorphous component on Mars suggests that it is made up of at least three phases: npOx, amorphous silicate (likely altered glass), and an amorphous S-bearing phase. Fundamental questions regarding the composition and the formation of the regional/global amorphous component(s) still remain: Do the phases form locally or have they been homogenized through aeolian activity and derived from the global dust? Is the parent glass volcanic, impact, or both? Are the phases separate or intimately mixed (e.g., as in palagonite)? When did the amorphous phases form? To address the question of source (local and/or global), we need to look for variations in the different phases within the amorphous component through continued modeling of the chemical composition of the amorphous phases in samples from Gale using CheMin and APXS data. If we find variations (e.g., a lack of or enrichment in amorphous silicate in some samples), this may imply a local source for some phases. Furthermore, the chemical composition of the weathering products may give insight into the formation mechanisms of the parent glass (e.g., impact glasses contain higher Al and lower Si [30], so we might expect allophane as a weathering product of impact glass). To address the question of whether these phases are separate or intimately mixed, we need to do laboratory studies of naturally altered samples made

  16. Amorphous Carbon-Boron Nitride Nanotube Hybrids

    Science.gov (United States)

    Kim, Jae Woo (Inventor); Siochi, Emilie J. (Inventor); Wise, Kristopher E. (Inventor); Lin, Yi (Inventor); Connell, John (Inventor)

    2016-01-01

    A method for joining or repairing boron nitride nanotubes (BNNTs). In joining BNNTs, the nanotube structure is modified with amorphous carbon deposited by controlled electron beam irradiation to form well bonded hybrid a-C/BNNT structures. In repairing BNNTs, the damaged site of the nanotube structure is modified with amorphous carbon deposited by controlled electron beam irradiation to form well bonded hybrid a-C/BNNT structures at the damage site.

  17. Amorphization Mechanism of Icosahedral Platinum Clusters

    International Nuclear Information System (INIS)

    Apra, Edoardo; Baletto, Francesca; Ferrando, Riccardo; Fortunelli, Alessandro

    2004-01-01

    The amorphization mechanism of high-symmetry pt nanoclusters is investigated by a combination of Molecular Dynamics simulations and Density Functional calculations. A general mechanism for amorphization, involving rosette-like structural transformations at fivefold vertices, is proposed. IN the tosette, a fivefold vertex is transformed into a hexagonal ring. We show that for icosahedral Pt nanoclusters, this transformation is associated with an energy gain, so that their most favorable structures have a low symmetry even at icosahedral magic numbers

  18. A Magnetic Sensor with Amorphous Wire

    Directory of Open Access Journals (Sweden)

    Dongfeng He

    2014-06-01

    Full Text Available Using a FeCoSiB amorphous wire and a coil wrapped around it, we have developed a sensitive magnetic sensor. When a 5 mm long amorphous wire with the diameter of 0.1 mm was used, the magnetic field noise spectrum of the sensor was about 30 pT/ÖHz above 30 Hz. To show the sensitivity and the spatial resolution, the magnetic field of a thousand Japanese yen was scanned with the magnetic sensor.

  19. Lithium ion conducting solid polymer blend electrolyte based on bio ...

    Indian Academy of Sciences (India)

    −4 Scm−1 has been observed for the composition of 70 PVA:30 PVP:25 Mwt% of LiNO3 with low activa- .... XRD pattern of (a) 70 PVA:30 PVP, (b) 70 PVA: .... charge carriers and also to the increase in the amorphous nature of the polymer electrolyte which reduces the energy barrier there by facilitating the ion trans- port.

  20. Polymer Nanocomposites

    Indian Academy of Sciences (India)

    thane, PVC, polyesters, polystyrene and polypropylene. Also, some biocompatible polymers like PLA, poly (E-caprolactone) to mention a few, have been synthesized by varying methods and with different clay loadings (%by weight). The hydrophobicity /hydrophilicity ofthe polymer affects its dispersion in the clay.

  1. Gelatin Nano-coating for Inhibiting Surface Crystallization of Amorphous Drugs.

    Science.gov (United States)

    Teerakapibal, Rattavut; Gui, Yue; Yu, Lian

    2018-01-05

    Inhibit the fast surface crystallization of amorphous drugs with gelatin nano-coatings. The free surface of amorphous films of indomethacin or nifedipine was coated by a gelatin solution (type A or B) and dried. The coating's effect on surface crystallization was evaluated. Coating thickness was estimated from mass change after coating. For indomethacin (weak acid, pK a  = 4.5), a gelatin coating of either type deposited at pH 5 and 10 inhibited its fast surface crystal growth. The coating thickness was 20 ± 10 nm. A gelatin coating deposited at pH 3, however, provided no protective effect. These results suggest that an effective gelatin coating does not require that the drug and the polymer have opposite charges. The ineffective pH 3 coating might reflect the poor wetting of indomethacin's neutral, hydrophobic surface by the coating solution. For nifedipine (weak base, pK a  = 2.6), a gelatin coating of either type deposited at pH 5 inhibited its fast surface crystal growth. Gelatin nano-coatings can be conveniently applied to amorphous drugs from solution to inhibit fast surface crystallization. Unlike strong polyelectrolyte coatings, a protective gelatin coating does not require strict pairing of opposite charges. This could make gelatin coating a versatile, pharmaceutically acceptable coating for stabilizing amorphous drugs.

  2. Effects of Polymeric Additives on the Crystallization and Release Behavior of Amorphous Ibuprofen

    Directory of Open Access Journals (Sweden)

    Su Yang Lee

    2013-01-01

    Full Text Available Some polymeric additives were studied to understand their effects on the amorphous phase of ibuprofen (IBU, used as a poorly water soluble pharmaceutical model compound. The amorphous IBU in bulk, as well as in nanopores (diameter ~24 nm of anodic aluminum oxide, was examined with the addition of poly(acrylic acid, poly(N-vinyl pyrrolidone, or poly(4-vinylphenol. Results of bulk crystallization showed that they were effective in limiting the crystal growth, while the nucleation of the crystalline phase in contact with water was nearly instantaneous in all cases. Poly(N-vinyl pyrrolidone, the most effective additive, was in specific interaction with IBU, as revealed by IR spectroscopy. The addition of the polymers was combined with the nanoscopic confinement to further stabilize the amorphous phase. Still, the IBU with addition of polymeric additives showed sustained release behavior. The current study suggested that the inhibition of the crystal nucleation was probably the most important factor to stabilize the amorphous phase and fully harness its high solubility.

  3. Ab initio simulation of amorphous silicon

    International Nuclear Information System (INIS)

    Cooper, N.C.; McKenzie, D.R.; Goringe, C.M.

    1999-01-01

    Full text: A first-principles Car-Parrinello molecular dynamics simulation of amorphous silicon is presented. Density Functional Theory is used to describe the forces between the atoms in a 64 atom supercell which is periodically repeated throughout space in order to generate an infinite network of atoms (a good approximation to a real solid). A quench from the liquid phase is used to achieve a quenched amorphous structure, which is subjected to an annealing cycle to improve its stability. The final, annealed network is in better agreement with experiment than any previous simulation of amorphous silicon. Significantly, the predicted average first-coordination numbers of 3.56 and 3.84 for the quenched and annealed structures from this simulation agree very closely with the experimental values of 3.55 and 3.90 respectively, whereas all previous simulations yielded first coordination numbers greater than 4. This improved agreement in coordination numbers is important because it supports the experimental finding that dangling bonds (which are associated with under-coordinated atoms) are more prevalent than floating bonds (the strained, longer bond of a five coordinate atom) in pure amorphous silicon. Finally, the effect of adding hydrogen to amorphous silicon was investigated by specifically placing hydrogen atoms at the likely defect sites. After a structural relaxation to optimise the positions of these hydrogen atoms, the localised electronic states associated with these defects are absent. Thus hydrogen is responsible for removing these defect states (which are able to trap carriers) from the edge of the band gap of the amorphous silicon. These results confirm the widely held ideas about the effect of hydrogen in producing remarkable improvements in the electronic properties of amorphous silicon

  4. Effects of the amorphization on hysteresis loops of the amorphous spin-1/2 Ising system

    International Nuclear Information System (INIS)

    Essaoudi, I.; Ainane, A.; Saber, M.; Miguel, J.J. de

    2009-01-01

    We examine the effects of the amorphization on the hysteresis loops of the amorphous spin-1/2 Ising system using the effective field theory within a probability distribution technique that accounts for the self-spin correlation functions. The magnetization, the transverse and longitudinal susceptibilities, and pyromagnetic coefficient are also studied in detail

  5. Conducting Polymer Based Nanobiosensors

    Directory of Open Access Journals (Sweden)

    Chul Soon Park

    2016-06-01

    Full Text Available In recent years, conducting polymer (CP nanomaterials have been used in a variety of fields, such as in energy, environmental, and biomedical applications, owing to their outstanding chemical and physical properties compared to conventional metal materials. In particular, nanobiosensors based on CP nanomaterials exhibit excellent performance sensing target molecules. The performance of CP nanobiosensors varies based on their size, shape, conductivity, and morphology, among other characteristics. Therefore, in this review, we provide an overview of the techniques commonly used to fabricate novel CP nanomaterials and their biosensor applications, including aptasensors, field-effect transistor (FET biosensors, human sense mimicking biosensors, and immunoassays. We also discuss prospects for state-of-the-art nanobiosensors using CP nanomaterials by focusing on strategies to overcome the current limitations.

  6. Molecular-dynamics simulations of thin polyisoprene films confined between amorphous silica substrates

    International Nuclear Information System (INIS)

    Guseva, D. V.; Komarov, P. V.; Lyulin, Alexey V.

    2014-01-01

    Constant temperature–constant pressure (NpT) molecular-dynamics computer simulations have been carried out for the united-atom model of a non-crosslinked (1,4) cis-polyisoprene (PI) melt confined between two amorphous, fully coordinated silica surfaces. The Lennard-Jones 12-6 potential was implemented to describe the polymer–silica interactions. The thickness H of the produced PI–silica film has been varied in a wide range, 1 g g is the individual PI chain radius of gyration measured under the imposed confinement. After a thorough equilibration, the PI film stratified structure and polymer segmental dynamics have been studied. The chain structure in the middle of the films resembles that in a corresponding bulk, but the polymer-density profile shows a pronounced ordering of the polymer segments in the vicinity of silica surfaces; this ordering disappears toward the film middles. Tremendous slowing down of the polymer segmental dynamics has been observed in the film surface layers, with the segmental relaxation more than 150 times slower as compared to that in a PI bulk. This effect increases with decreasing the polymer-film thickness. The segmental relaxation in the PI film middles shows additional relaxation process which is absent in a PI bulk. Even though there are fast relaxation processes in the film middle, its overall relaxation is slower as compared to that in a bulk sample. The interpretation of the results in terms of polymer glassy bridges has been discussed

  7. Antisolvent Recrystallization Strategy to Screen Appropriate Carriers to Stabilize Filgotinib Amorphous Solid Dispersions.

    Science.gov (United States)

    Ren, Fuzheng; Sun, Hanjing; Cui, Lin; Si, Yike; Chen, Ning; Ren, Guobin; Jing, Qiufang

    2018-02-16

    Drugs in amorphous solid dispersions (ASDs) are highly dispersed in hydrophilic polymeric carriers, which also help to restrain recrystallization and stabilize the ASDs. In this study, microscopic observation after antisolvent recrystallization was developed as a rapid screening method to select appropriate polymers for the initial design filgotinib (FTN) ASDs. Using solvent evaporation, FTN ASDs with the polymers were prepared, and accelerated experimentation validated this screening method. Fourier-transform infrared spectroscopy, Raman scattering, and nuclear magnetic resonance revealed hydrogen-bonding formation in the drug-polymer binary system, which was critical for ASDs stabilization. A Flory-Huggins interaction parameter and water sorption isotherms were applied to evaluate the strength of the interaction between FTN and the polymers. The dissolution rate was also significantly improved by ASDs formulation, and the presence of the polymers exerted solubilization effects. These results suggested the efficacy of this screening method as a preliminary tool for polymer selection in ASDs design. Copyright © 2018 American Pharmacists Association®. Published by Elsevier Inc. All rights reserved.

  8. Nanowire Tunnel Field Effect Transistors: Prospects and Pitfalls

    OpenAIRE

    Sylvia, Somaia Sarwat

    2014-01-01

    The tunnel field effect transistor (TFET) has the potential to operate at lower voltages and lower power than the field effect transistor (FET). The TFET can circumvent the fundamental thermal limit of the inverse subthreshold slope (S) by exploiting interband tunneling of non-equilibrium "cold" carriers. The conduction mechanism in the TFET is governed by band-to-band tunneling which limits the drive current. TFETs built with III-V materials like InAs and InSb can produce enough tunneling cu...

  9. Strontium titanate resistance modulation by ferroelectric field effect

    CERN Document Server

    Marré, D; Bellingeri, E; Pallecchi, I; Pellegrino, L; Siri, A S

    2003-01-01

    Among perovskite oxides strontium titanate (STO) SrTiO sub 3 undergoes a metal-insulator transition at very low carrier concentration and exhibits high mobility values at low temperature. We exploited such electrical properties and the structural compatibility of perovskite oxide materials in realizing ferroelectric field effect epitaxial heterostructures. By pulsed laser deposition, we grew patterned field effect devices, consisting of lanthanum doped STO and Pb(Zr,Ti)O sub 3. Such devices showed a resistance modulation up to 20%, consistent with geometrical parameters and carrier concentration of the semiconducting channel.

  10. A Water-Soluble Polythiophene for Organic Field-Effect Transistors

    Energy Technology Data Exchange (ETDEWEB)

    Shao, Ming [ORNL; He, Youjun [ORNL; Hong, Kunlun [ORNL; Rouleau, Christopher M [ORNL; Geohegan, David B [ORNL; Xiao, Kai [ORNL

    2013-01-01

    Synthesis of a non-ionic, water-soluble poly(thiophene) (PT) derivative, poly(3-(2-(2-methoxyethoxy) ethoxy)ethoxy) methylthiophene) (P3TEGT) with a hydrophilic tri-ethylene glycol side group, is reported and thin films of the polymer suitable for organic field-effect transistors (OFETs) are characterized by combining analysis techniques that include UV-Vis absorption and fluorescence spectroscopy, x-ray diffraction, and atomic force microscopy. After thermal annealing, P3TEGT films exhibit a well-organized nanofibrillar lamellar nanostructure that originates from the strong - stacking of the thiophene backbones. P-type organic field-effect transistors (OFETs) with hole mobilities of 10-5 cm2V-1s-1 were fabricated from this water-soluble poly(thiophene) derivative, demonstrating the possibility that environmentally-friendly solvents may be promising alternatives for the low-cost, green solution-based organic electronic device manufacturing of OFETs, organic photovoltaics (OPVs), and biosensors.

  11. Solution-processed ambipolar organic field-effect transistors and inverters.

    Science.gov (United States)

    Meijer, E J; de Leeuw, D M; Setayesh, S; van Veenendaal, E; Huisman, B H; Blom, P W M; Hummelen, J C; Scherf, U; Kadam, J; Klapwijk, T M

    2003-10-01

    There is ample evidence that organic field-effect transistors have reached a stage where they can be industrialized, analogous to standard metal oxide semiconductor (MOS) transistors. Monocrystalline silicon technology is largely based on complementary MOS (CMOS) structures that use both n-type and p-type transistor channels. This complementary technology has enabled the construction of digital circuits, which operate with a high robustness, low power dissipation and a good noise margin. For the design of efficient organic integrated circuits, there is an urgent need for complementary technology, where both n-type and p-type transistor operation is realized in a single layer, while maintaining the attractiveness of easy solution processing. We demonstrate, by using solution-processed field-effect transistors, that hole transport and electron transport are both generic properties of organic semiconductors. This ambipolar transport is observed in polymers based on interpenetrating networks as well as in narrow bandgap organic semiconductors. We combine the organic ambipolar transistors into functional CMOS-like inverters.

  12. Iron-based amorphous alloys and methods of synthesizing iron-based amorphous alloys

    Science.gov (United States)

    Saw, Cheng Kiong; Bauer, William A.; Choi, Jor-Shan; Day, Dan; Farmer, Joseph C.

    2016-05-03

    A method according to one embodiment includes combining an amorphous iron-based alloy and at least one metal selected from a group consisting of molybdenum, chromium, tungsten, boron, gadolinium, nickel phosphorous, yttrium, and alloys thereof to form a mixture, wherein the at least one metal is present in the mixture from about 5 atomic percent (at %) to about 55 at %; and ball milling the mixture at least until an amorphous alloy of the iron-based alloy and the at least one metal is formed. Several amorphous iron-based metal alloys are also presented, including corrosion-resistant amorphous iron-based metal alloys and radiation-shielding amorphous iron-based metal alloys.

  13. Vacuum-and-solvent-free fabrication of organic semiconductor layers for field-effect transistors

    Science.gov (United States)

    Matsushima, Toshinori; Sandanayaka, Atula S. D.; Esaki, Yu; Adachi, Chihaya

    2015-09-01

    We demonstrate that cold and hot isostatic pressing (CIP and HIP) is a novel, alternative method for organic semiconductor layer fabrication, where organic powder is compressed into a layer shape directly on a substrate with 200 MPa pressure. Spatial gaps between powder particles and the other particles, substrates, or electrodes are crushed after CIP and HIP, making it possible to operate organic field-effect transistors (OFETs) containing the compressed powder as the semiconductor. The CIP-compressed powder of 2,7-dioctyl[1]benzothieno[3,2-b][1]benzothiophene (C8-BTBT) had a hole mobility of (1.6 ± 0.4) × 10-2 cm2/Vs. HIP of C8-BTBT powder increased the hole mobility to an amorphous silicon-like value (0.22 ± 0.07 cm2/Vs) because of the growth of the C8-BTBT crystallites and the improved continuity between the powder particles. The vacuum and solution processes are not involved in our CIP and HIP techniques, offering a possibility of manufacturing OFETs at low cost.

  14. Crystal and molecular simulation of high-performance polymers.

    Science.gov (United States)

    Colquhoun, H M; Williams, D J

    2000-03-01

    Single-crystal X-ray analyses of oligomeric models for high-performance aromatic polymers, interfaced to computer-based molecular modeling and diffraction simulation, have enabled the determination of a range of previously unknown polymer crystal structures from X-ray powder data. Materials which have been successfully analyzed using this approach include aromatic polyesters, polyetherketones, polythioetherketones, polyphenylenes, and polycarboranes. Pure macrocyclic homologues of noncrystalline polyethersulfones afford high-quality single crystals-even at very large ring sizes-and have provided the first examples of a "protein crystallographic" approach to the structures of conventionally amorphous synthetic polymers.

  15. Ta-based amorphous metal thin films

    Energy Technology Data Exchange (ETDEWEB)

    McGlone, John M., E-mail: mcglone@eecs.oregonstate.edu [School of Electrical Engineering and Computer Science, Oregon State University, Corvallis, OR 97331-5501 (United States); Olsen, Kristopher R. [Department of Chemistry, Oregon State University, Corvallis, OR 97331-4003 (United States); Stickle, William F.; Abbott, James E.; Pugliese, Roberto A.; Long, Greg S. [Hewlett-Packard Company, Corvallis, OR, 97333 (United States); Keszler, Douglas A. [Department of Chemistry, Oregon State University, Corvallis, OR 97331-4003 (United States); Wager, John F. [School of Electrical Engineering and Computer Science, Oregon State University, Corvallis, OR 97331-5501 (United States)

    2015-11-25

    With their lack of grains and grain boundaries, amorphous metals are known to possess advantageous mechanical properties and enhanced chemical stability relative to crystalline metals. Commonly, however, they exhibit poor high-temperature stability because of their metastable nature. Here, we describe two new Ta-based ternary metal thin films that retain thermal stability to 600 °C and above. The new thin-film compositions, Ta{sub 2}Ni{sub 2}Si{sub 1} and Ta{sub 2}Mo{sub 2}Si{sub 1}, are amorphous, exhibiting ultra-smooth surfaces (<0.4 nm) and resistivities typical of amorphous metals (224 and 177 μΩ cm, respectively). - Highlights: • New Ta-based amorphous metals were sputter deposited from individual targets. • As-deposited amorphous structure was confirmed through diffraction techniques. • Electrical and surface properties were characterized and possess smooth surfaces. • No evidence of crystallization up to 600 °C (TaNiSi) and 800 °C (TaMoSi). • Ultra-smooth surfaces remained unchanged up to crystallization temperature.

  16. Amorphous silicon detectors in positron emission tomography

    International Nuclear Information System (INIS)

    Conti, M.; Perez-Mendez, V.

    1989-12-01

    The physics of the detection process is studied and the performances of different Positron Emission Tomography (PET) system are evaluated by theoretical calculation and/or Monte Carlo Simulation (using the EGS code) in this paper, whose table of contents can be summarized as follows: a brief introduction to amorphous silicon detectors and some useful equation is presented; a Tantalum/Amorphous Silicon PET project is studied and the efficiency of the systems is studied by Monte Carlo Simulation; two similar CsI/Amorphous Silicon PET projects are presented and their efficiency and spatial resolution are studied by Monte Carlo Simulation, light yield and time characteristics of the scintillation light are discussed for different scintillators; some experimental result on light yield measurements are presented; a Xenon/Amorphous Silicon PET is presented, the physical mechanism of scintillation in Xenon is explained, a theoretical estimation of total light yield in Xenon and the resulting efficiency is discussed altogether with some consideration of the time resolution of the system; the amorphous silicon integrated electronics is presented, total noise and time resolution are evaluated in each of our applications; the merit parameters ε 2 τ's are evaluated and compared with other PET systems and conclusions are drawn; and a complete reference list for Xenon scintillation light physics and its applications is presented altogether with the listing of the developed simulation programs

  17. Amorphous silicon detectors in positron emission tomography

    Energy Technology Data Exchange (ETDEWEB)

    Conti, M. (Istituto Nazionale di Fisica Nucleare, Pisa (Italy) Lawrence Berkeley Lab., CA (USA)); Perez-Mendez, V. (Lawrence Berkeley Lab., CA (USA))

    1989-12-01

    The physics of the detection process is studied and the performances of different Positron Emission Tomography (PET) system are evaluated by theoretical calculation and/or Monte Carlo Simulation (using the EGS code) in this paper, whose table of contents can be summarized as follows: a brief introduction to amorphous silicon detectors and some useful equation is presented; a Tantalum/Amorphous Silicon PET project is studied and the efficiency of the systems is studied by Monte Carlo Simulation; two similar CsI/Amorphous Silicon PET projects are presented and their efficiency and spatial resolution are studied by Monte Carlo Simulation, light yield and time characteristics of the scintillation light are discussed for different scintillators; some experimental result on light yield measurements are presented; a Xenon/Amorphous Silicon PET is presented, the physical mechanism of scintillation in Xenon is explained, a theoretical estimation of total light yield in Xenon and the resulting efficiency is discussed altogether with some consideration of the time resolution of the system; the amorphous silicon integrated electronics is presented, total noise and time resolution are evaluated in each of our applications; the merit parameters {epsilon}{sup 2}{tau}'s are evaluated and compared with other PET systems and conclusions are drawn; and a complete reference list for Xenon scintillation light physics and its applications is presented altogether with the listing of the developed simulation programs.

  18. The Structure of Liquid and Amorphous Hafnia

    Directory of Open Access Journals (Sweden)

    Leighanne C. Gallington

    2017-11-01

    Full Text Available Understanding the atomic structure of amorphous solids is important in predicting and tuning their macroscopic behavior. Here, we use a combination of high-energy X-ray diffraction, neutron diffraction, and molecular dynamics simulations to benchmark the atomic interactions in the high temperature stable liquid and low-density amorphous solid states of hafnia. The diffraction results reveal an average Hf–O coordination number of ~7 exists in both the liquid and amorphous nanoparticle forms studied. The measured pair distribution functions are compared to those generated from several simulation models in the literature. We have also performed ab initio and classical molecular dynamics simulations that show density has a strong effect on the polyhedral connectivity. The liquid shows a broad distribution of Hf–Hf interactions, while the formation of low-density amorphous nanoclusters can reproduce the sharp split peak in the Hf–Hf partial pair distribution function observed in experiment. The agglomeration of amorphous nanoparticles condensed from the gas phase is associated with the formation of both edge-sharing and corner-sharing HfO6,7 polyhedra resembling that observed in the monoclinic phase.

  19. Molecular origins of anisotropic shock propagation in crystalline and amorphous polyethylene

    Science.gov (United States)

    O'Connor, Thomas C.; Elder, Robert M.; Sliozberg, Yelena R.; Sirk, Timothy W.; Andzelm, Jan W.; Robbins, Mark O.

    2018-03-01

    Molecular dynamics simulations are used to analyze shock propagation in amorphous and crystalline polyethylene. Results for the shock velocity Us are compared to predictions from Pastine's equation of state and hydrostatic theory. The results agree with Pastine at high impact velocities. At low velocities the yield stress becomes important, increasing the shock velocity and leading to anisotropy in the crystalline response. Detailed analysis of changes in atomic order reveals the origin of the anisotropic response. For shock along the polymer backbone, an elastic front is followed by a plastic front where chains buckle with a characteristic wavelength. Shock perpendicular to the chain backbone can produce plastic deformation or transitions to different orthorhombic or monoclinic structures, depending on the impact speed and direction. Tensile loading does not produce stable shocks: Amorphous systems craze and fracture while for crystals the front broadens linearly with time.

  20. Method of making a self-aligned schottky metal semi-conductor field effect transistor with buried source and drain

    International Nuclear Information System (INIS)

    Bol, I.

    1984-01-01

    A semi-conductor structure and particularly a high speed VLSI Self-Aligned Schottky Metal Semi-Conductor Field Effect Transistor with buried source and drain, fabricated by the ion implantation of source and drain areas at a predetermined range of depths followed by very localized laser annealing to electrically reactivate the amorphous buried source and drain areas thereby providing effective vertical separation of the channel from the buried source and drain respectively. Accordingly, spatial separations between the self-aligned gate-to-drain, and gate-to-source can be relatively very closely controlled by varying the doping intensity and duration of the implantation thereby reducing the series resistance and increasing the operating speed

  1. Organometallic Polymers.

    Science.gov (United States)

    Carraher, Charles E., Jr.

    1981-01-01

    Reactions utilized to incorporate a metal-containing moiety into a polymer chain (addition, condensation, and coordination) are considered, emphasizing that these reactions also apply to smaller molecules. (JN)

  2. Large scale integration of flexible non-volatile, re-addressable memories using P(VDF-TrFE) and amorphous oxide transistors

    NARCIS (Netherlands)

    Gelinck, G.H.; Cobb, B.; Breemen, A.J.J.M. van; Myny, K.

    2015-01-01

    Ferroelectric polymers and amorphous metal oxide semiconductors have emerged as important materials for re-programmable non-volatile memories and high-performance, flexible thin-film transistors, respectively. However, realizing sophisticated transistor memory arrays has proven to be a challenge,

  3. Ambipolar light-emitting organic field-effect transistor

    NARCIS (Netherlands)

    Rost, Constance; Karg, Siegfried; Riess, Walter; Loi, Maria Antonietta; Murgia, Mauro; Muccini, Michele

    2004-01-01

    We demonstrate a light-emitting organic field-effect transistor (OFET) with pronounced ambipolar current characteristics. The ambipolar transport layer is a coevaporated thin film of α-quinquethiophene (α-5T) as hole-transport material and N,N'-ditridecylperylene-3,4,9,10-tetracarboxylic diimide

  4. Bimolecular recombination in ambipolar organic field effect transistors

    NARCIS (Netherlands)

    Charrier, D.S.H.; Vries, T. de; Mathijssen, S.G.J.; Geluk, E.-J.; Smits, E.C.P.; Kemerink, M.; Janssen, R.A.J.

    2009-01-01

    In ambipolar organic field effect transistors (OFET) the shape of the channel potential is intimately related to the recombination zone width W, and hence to the electron–hole recombination strength. Experimentally, the recombination profile can be assessed by scanning Kelvin probe microscopy

  5. Electronic properties of germanane field-effect transistors

    NARCIS (Netherlands)

    Madhushankar, B.N.; Kaverzin, A.; Giousis, T.; Potsi, G.; Gournis, D.; Rudolf, P.; Blake, G.R.; van der Wal, C.H.; van Wees, B.J.

    2017-01-01

    A new two dimensional (2D) material—germanane—has been synthesised recently with promising electrical and optical properties. In this paper we report the first realisation of germanane field-effect transistors fabricated from multilayer single crystal flakes. Our germanane devices show transport in

  6. Single-molecule probes in organic field-effect transistors

    NARCIS (Netherlands)

    Nicolet, Aurélien Armel Louis

    2007-01-01

    The goal of this thesis is to study charge transport phenomena in organic materials. This is done optically by means of single-molecule spectroscopy in a field-effect transistor based on a molecular crystal. We present (in Chapter 2) a fundamental requirement for single-molecule spectroscopy

  7. Physics of organic ferroelectric field-effect transistors

    NARCIS (Netherlands)

    Brondijk, J.J.; Asadi, K.; Blom, P.W.M.; Leeuw, D.M. de

    2012-01-01

    Most of the envisaged applications of organic electronics require a nonvolatile memory that can be programmed, erased, and read electrically. Ferroelectric field-effect transistors (FeFET) are especially suitable due to the nondestructive read-out and low power consumption. Here, an analytical model

  8. Field-effect pH Control in Nanochannels

    NARCIS (Netherlands)

    Veenhuis, R.B.H.; van der Wouden, E.J.; van Nieuwkasteele, Jan William; van den Berg, Albert; Eijkel, Jan C.T.; Kim, Tae Song; Lee, Yoon-Sik; Chung, Taek-Dong; Jeon, Noo Li; Lee, Sang-Hoon; Suh, Kaph-Yang; Choo, Jaebum; Kim, Yong-Kweon

    2009-01-01

    We demonstrate a novel capacitive method to change the pH in nanochannels. The device employs metal electrodes outside an insulating channel wall to change the electrical double layer potential by the field effect (‘voltage gating’). We demonstrate that this potential change is accompanied by a

  9. Nanoscaled biological gated field effect transistors for cytogenetic analysis

    DEFF Research Database (Denmark)

    Kwasny, Dorota; Dimaki, Maria; Andersen, Karsten Brandt

    2014-01-01

    Cytogenetic analysis is the study of chromosome structure and function, and is often used in cancer diagnosis, as many chromosome abnormalities are linked to the onset of cancer. A novel label free detection method for chromosomal translocation analysis using nanoscaled field effect transistors...

  10. Time-reversal symmetry breaking by ac field: Effect of ...

    Indian Academy of Sciences (India)

    Time-reversal symmetry breaking by ac field: Effect of commensurability in the frequency domain. V E KRAVTSOV. Present address: The Abdus Salam International Centre for Theoretical Physics, P.O. Box 586, 34100. Trieste, Italy. Landau Institute for Theoretical Physics, 2 Kosygina Street, 117940 Moscow, Russia.

  11. Polymers All Around You!

    Science.gov (United States)

    Gertz, Susan

    Background information on natural polymers, synthetic polymers, and the properties of polymers is presented as an introduction to this curriculum guide. Details are provided on the use of polymer products in consumer goods, polymer recycling, polymer densities, the making of a polymer such as GLUEP, polyvinyl alcohol, dissolving plastics, polymers…

  12. Formation of amorphous layers by irradiation

    International Nuclear Information System (INIS)

    Bourgoin, J.C.

    1979-01-01

    When an ordered solid is irradiated with heavy energy particles, disorder is produced. When the irradiation dose exceeds a so-called critical dose, the irradiated area of the solid becomes uniformly disordered. Mention is first made of the nature, concentration and distribution of the defects created by a heavy energy particle. The description is then given -solely with respect to semiconductors- of the effect of the various parameters on the critical dose energy and nature of the ion, nature and temperature of the solid, irradiation flux. The physical properties (electronic and thermodynamic types) and the uniformly disordered areas are briefly discussed and these properties are compared with those of amorphous semiconductor layers fabricated by evaporation. It is concluded that the evaporated and irradiated layers are similar in nature. It is suggested that the transformation of an irradiated crystalline area into an amorphous one occurs when the Gibbs energy of the crystal become greater than the Gibbs energy of the amorphous one [fr

  13. Phase transitions in biogenic amorphous calcium carbonate.

    Science.gov (United States)

    Gong, Yutao U T; Killian, Christopher E; Olson, Ian C; Appathurai, Narayana P; Amasino, Audra L; Martin, Michael C; Holt, Liam J; Wilt, Fred H; Gilbert, P U P A

    2012-04-17

    Crystalline biominerals do not resemble faceted crystals. Current explanations for this property involve formation via amorphous phases. Using X-ray absorption near-edge structure (XANES) spectroscopy and photoelectron emission microscopy (PEEM), here we examine forming spicules in embryos of Strongylocentrotus purpuratus sea urchins, and observe a sequence of three mineral phases: hydrated amorphous calcium carbonate (ACC · H(2)O) → dehydrated amorphous calcium carbonate (ACC) → calcite. Unexpectedly, we find ACC · H(2)O-rich nanoparticles that persist after the surrounding mineral has dehydrated and crystallized. Protein matrix components occluded within the mineral must inhibit ACC · H(2)O dehydration. We devised an in vitro, also using XANES-PEEM, assay to identify spicule proteins that may play a role in stabilizing various mineral phases, and found that the most abundant occluded matrix protein in the sea urchin spicules, SM50, stabilizes ACC · H(2)O in vitro.

  14. Fabrication and application of amorphous semiconductor devices

    International Nuclear Information System (INIS)

    Kumurdjian, Pierre.

    1976-01-01

    This invention concerns the design and manufacture of elecric switching or memorisation components with amorphous semiconductors. As is known some compounds, particularly the chalcogenides, have a resistivity of the semiconductor type in the amorphous solid state. These materials are obtained by the high temperature homogeneisation of several single elements such as tellurium, arsenic, germanium and sulphur, followed by water or air quenching. In particular these compounds have useful switching and memorisation properties. In particular they have the characteristic of not suffering deterioration when placed in an environment subjected to nuclear radiations. In order to know more about the nature and properties of these amorphous semiconductors the French patent No. 71 28048 of 30 June 1971 may be consulted with advantage [fr

  15. Heavy ions amorphous semiconductors irradiation study

    International Nuclear Information System (INIS)

    Benmalek, M.

    1978-01-01

    The behavior of amorphous semiconductors (germanium and germanium and arsenic tellurides) under ion bombardment at energies up to 2 MeV was studied. The irradiation induced modifications were followed using electrical parameter changes (resistivity and activation energy) and by means of the transmission electron microscopy observations. The electrical conductivity enhancement of the irradiated samples was interpreted using the late conduction theories in amorphous compounds. In amorphous germanium, Electron Microscopy showed the formations of 'globules', these defects are similar to voids observed in irradiated metals. The displacement cascade theory was used for the interpretation of the irradiation induced defects formation and a coalescence mechanism of growth was pointed out for the vacancy agglomeration [fr

  16. Amorphous Silica-Promoted Lysine Dimerization: a Thermodynamic Prediction

    Science.gov (United States)

    Kitadai, Norio; Nishiuchi, Kumiko; Nishii, Akari; Fukushi, Keisuke

    2018-03-01

    It has long been suggested that mineral surfaces played a crucial role in the abiotic polymerization of amino acids that preceded the origin of life. Nevertheless, it remains unclear where the prebiotic process took place on the primitive Earth, because the amino acid-mineral interaction and its dependence on environmental conditions have yet to be understood adequately. Here we examined experimentally the adsorption of L-lysine (Lys) and its dimer (LysLys) on amorphous silica over a wide range of pH, ionic strength, adsorbate concentration, and the solid/water ratio, and determined the reaction stoichiometries and the equilibrium constants based on the extended triple-layer model (ETLM). The retrieved ETLM parameters were then used, in combination with the equilibrium constant for the peptide bond formation in bulk water, to calculate the Lys-LysLys equilibrium in the presence of amorphous silica under various aqueous conditions. Results showed that the silica surface favors Lys dimerization, and the influence varies greatly with changing environmental parameters. At slightly alkaline pH (pH 9) in the presence of a dilute NaCl (1 mM), the thermodynamically attainable LysLys from 0.1 mM Lys reached a concentration around 50 times larger than that calculated without silica. Because of the versatility of the ETLM, which has been applied to describe a wide variety of biomolecule-mineral interactions, future experiments with the reported methodology are expected to provide a significant constraint on the plausible geological settings for the condensation of monomers to polymers, and the subsequent chemical evolution of life.

  17. The application of orthogonal photolithography to micro-scale organic field effect transistors and complementary inverters on flexible substrate

    Energy Technology Data Exchange (ETDEWEB)

    Jang, Jingon; Song, Younggul; Yoo, Daekyoung; Kim, Dongku; Lee, Hyungwoo; Hong, Seunghun; Lee, Takhee, E-mail: tlee@snu.ac.kr [Department of Physics and Astronomy, and Institute of Applied Physics, Seoul National University, Seoul 151-747 (Korea, Republic of); Oh, Hyuntaek; Lee, Jin-Kyun, E-mail: jkl36@inha.ac.kr [Department of Polymer Science and Engineering, Inha University, Incheon 402-751 (Korea, Republic of)

    2014-02-03

    Micro-scale pentacene organic field effect transistors (OFETs) were fabricated on a flexible poly(ethylene terephthalate) (PET) substrate. By applying a highly fluorinated developing solvents and its compatible photoresist materials, it has become possible to make the micro-scale patterning for organic devices using standard photolithography without damaging the underlying polymer layers. The flexible pentacene OFETs with 3 μm-sized channel length exhibited stable electrical characteristics under bent configurations and under a large number of repetitive bending cycles. Furthermore, we demonstrated micro-scale organic complementary inverters on a flexible PET substrate using p-type pentacene and n-type copper hexadecafluorophthalocyanine materials.

  18. The application of orthogonal photolithography to micro-scale organic field effect transistors and complementary inverters on flexible substrate

    International Nuclear Information System (INIS)

    Jang, Jingon; Song, Younggul; Yoo, Daekyoung; Kim, Dongku; Lee, Hyungwoo; Hong, Seunghun; Lee, Takhee; Oh, Hyuntaek; Lee, Jin-Kyun

    2014-01-01

    Micro-scale pentacene organic field effect transistors (OFETs) were fabricated on a flexible poly(ethylene terephthalate) (PET) substrate. By applying a highly fluorinated developing solvents and its compatible photoresist materials, it has become possible to make the micro-scale patterning for organic devices using standard photolithography without damaging the underlying polymer layers. The flexible pentacene OFETs with 3 μm-sized channel length exhibited stable electrical characteristics under bent configurations and under a large number of repetitive bending cycles. Furthermore, we demonstrated micro-scale organic complementary inverters on a flexible PET substrate using p-type pentacene and n-type copper hexadecafluorophthalocyanine materials

  19. On the methodology of the determination of charge concentration dependent mobility from organic field-effect transistor characteristics

    Czech Academy of Sciences Publication Activity Database

    Menšík, Miroslav; Toman, Petr; Bielecka, U.; Bartkowiak, W.; Pfleger, Jiří; Paruzel, Bartosz

    2018-01-01

    Roč. 20, č. 4 (2018), s. 2308-2319 ISSN 1463-9076 R&D Projects: GA ČR(CZ) GA15-05095S; GA MŠk(CZ) LTC17029 EU Projects: European Commission(XE) MPNS COST Action MP1406 Institutional support: RVO:61389013 Keywords : field effect transistor * charge carrier mobility * conjugated polymer Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 4.123, year: 2016

  20. Ion bombardment and disorder in amorphous silicon

    International Nuclear Information System (INIS)

    Sidhu, L.S.; Gaspari, F.; Zukotynski, S.

    1997-01-01

    The effect of ion bombardment during growth on the structural and optical properties of amorphous silicon are presented. Two series of films were deposited under electrically grounded and positively biased substrate conditions. The biased samples displayed lower growth rates and increased hydrogen content relative to grounded counterparts. The film structure was examined using Raman spectroscopy. The transverse optic like phonon band position was used as a parameter to characterize network order. Biased samples displayed an increased order of the amorphous network relative to grounded samples. Furthermore, biased samples exhibited a larger optical gap. These results are correlated and attributed to reduced ion bombardment effects

  1. Amorphous Silicon-Carbon Nanostructure Photovoltaic Devices

    OpenAIRE

    Schriver, Maria Christine

    2012-01-01

    A novel solar cell architecture made completely from the earth abundant elements silicon and carbon has been developed. Hydrogenated amorphous silicon (aSi:H), rather than crystalline silicon, is used as the active material due to its high absorption through a direct band gap of 1.7eV, well matched to the solar spectrum to ensure the possibility of improved cells in this architecture with higher efficiencies. The cells employ a Schottky barrier design wherein the amorphous silicon absorber la...

  2. Irradiation induced crystalline to amorphous transition

    International Nuclear Information System (INIS)

    Bourgoin, J.

    1980-01-01

    Irradiation of a crystalline solid with energetic heavy particles results in cascades of defects which, with increasing dose, overlap and form a continuous disordered layer. In semiconductors the physical properties of such disordered layers are found to be similar to those of amorphous layers produced by evaporation. It is shown in the case of silicon, that the transition from a disordered crystalline (X) layer to an amorphous (α) layer occurs when the Gibbs energy of the X phase and of the defects it contains becomes larger than the Gibbs energy of the α phase. (author)

  3. Electronic properties of intrinsic and doped amorphous silicon carbide films

    Energy Technology Data Exchange (ETDEWEB)

    Vetter, M. [Departament d' Enginyeria Electronica, Universitat Politecnica de Catalunya, Gran Capita s/n, Modul C4, E-08034 Barcelona (Spain)]. E-mail: mvetter@eel.upc.edu; Voz, C. [Departament d' Enginyeria Electronica, Universitat Politecnica de Catalunya, Gran Capita s/n, Modul C4, E-08034 Barcelona (Spain); Ferre, R. [Departament d' Enginyeria Electronica, Universitat Politecnica de Catalunya, Gran Capita s/n, Modul C4, E-08034 Barcelona (Spain); Martin, I. [Departament d' Enginyeria Electronica, Universitat Politecnica de Catalunya, Gran Capita s/n, Modul C4, E-08034 Barcelona (Spain); Orpella, A. [Departament d' Enginyeria Electronica, Universitat Politecnica de Catalunya, Gran Capita s/n, Modul C4, E-08034 Barcelona (Spain); Puigdollers, J. [Departament d' Enginyeria Electronica, Universitat Politecnica de Catalunya, Gran Capita s/n, Modul C4, E-08034 Barcelona (Spain); Andreu, J. [Departament de Fisica Aplicada i Optica, Universitat de Barcelona, Av. Diagonal 647, E-08028 Barcelona (Spain); Alcubilla, R. [Departament d' Enginyeria Electronica, Universitat Politecnica de Catalunya, Gran Capita s/n, Modul C4, E-08034 Barcelona (Spain)

    2006-07-26

    Hydrogenated amorphous silicon carbide (a-SiC{sub x} : H) films have shown excellent surface passivation of crystalline silicon. With the aim of large area deposition of these films the influence of the rf plasma power was investigated. It is found that homogenous deposition with effective surface recombination velocity lower than 100 cms{sup -1} is possible up to 6'' diameter in a simple parallel plate reactor by optimizing deposition parameters. For application in solar cell processes the conductivity of these a-SiC{sub x} : H films might become of importance since good surface passivation results from field-effect passivation which needs an insulating dielectric layer. Therefore, the temperature dependence of the dark dc conductivity of these films was investigated in the temperature range from - 20 to 260 deg. C. Two transition temperatures, T {sub s}{approx}80 deg. C and T {sub s}{approx}170 deg. C, were found where conductivity increases, resp. decreases over-exponential. From Arrhenius plots activation energy (E {sub a}) and conductivity pre-factor ({sigma} {sub 0}) were calculated for a large number of samples with different composition. A correlation between E {sub a} and {sigma} {sub 0} was found giving a Meyer-Neldel relation with a slope of 59 mV, corresponding to a material characteristic temperature T {sub m} = 400 deg. C, and an intercept at {sigma} {sub 00} = 0.1 {omega}{sup -1}cm{sup -1}.

  4. Electronic properties of intrinsic and doped amorphous silicon carbide films

    International Nuclear Information System (INIS)

    Vetter, M.; Voz, C.; Ferre, R.; Martin, I.; Orpella, A.; Puigdollers, J.; Andreu, J.; Alcubilla, R.

    2006-01-01

    Hydrogenated amorphous silicon carbide (a-SiC x : H) films have shown excellent surface passivation of crystalline silicon. With the aim of large area deposition of these films the influence of the rf plasma power was investigated. It is found that homogenous deposition with effective surface recombination velocity lower than 100 cms -1 is possible up to 6'' diameter in a simple parallel plate reactor by optimizing deposition parameters. For application in solar cell processes the conductivity of these a-SiC x : H films might become of importance since good surface passivation results from field-effect passivation which needs an insulating dielectric layer. Therefore, the temperature dependence of the dark dc conductivity of these films was investigated in the temperature range from - 20 to 260 deg. C. Two transition temperatures, T s ∼80 deg. C and T s ∼170 deg. C, were found where conductivity increases, resp. decreases over-exponential. From Arrhenius plots activation energy (E a ) and conductivity pre-factor (σ 0 ) were calculated for a large number of samples with different composition. A correlation between E a and σ 0 was found giving a Meyer-Neldel relation with a slope of 59 mV, corresponding to a material characteristic temperature T m = 400 deg. C, and an intercept at σ 00 = 0.1 Ω -1 cm -1

  5. Degradation of L-Ascorbic Acid in the Amorphous Solid State.

    Science.gov (United States)

    Sanchez, Juan O; Ismail, Yahya; Christina, Belinda; Mauer, Lisa J

    2018-03-01

    Ascorbic acid degradation in amorphous solid dispersions was compared to its degradation in the crystalline state. Physical blends and lyophiles of ascorbic acid and polymers (pectins and polyvinylpyrrolidone [PVP]) were prepared initially at 50:50 (w/w), with further studies using the polymer that best inhibited ascorbic acid crystallization in the lyophiles in 14 vitamin : PVP ratios. Samples were stored in controlled environments (25 to 60 °C, 0% to 23% RH) for 1 mo and analyzed periodically to track the physical appearance, change in moisture content, physical state (powder x-ray diffraction and polarized light microscopy), and vitamin loss (high performance liquid chromatography) over time. The glass transition temperatures of select samples were determined using differential scanning calorimetry, and moisture sorption profiles were generated. Ascorbic acid in the amorphous form, even in the glassy amorphous state, was more labile than in the crystalline form in some formulations at the highest storage temperature. Lyophiles stored at 25 and 40 °C and those in which ascorbic acid had crystallized at 60 °C (≥70% ascorbic acid : PVP) had no significant difference in vitamin loss (P > 0.05) relative to physical blend controls, and the length of storage had little effect. At 60 °C, amorphous ascorbic acid lyophiles (≤60% ascorbic acid : PVP) lost significantly more vitamin (P degradation also significantly increased (P < 0.05) at lower proportions of ascorbic acid, a scenario likely encountered in foods wherein vitamins are naturally present or added at low concentrations and production practices may promote amorphization of the vitamin. Vitamin C is one of the most unstable vitamins in foods. This study documents that amorphous ascorbic acid is less stable than crystalline ascorbic acid in some environments (for example, higher temperatures within 1 wk), especially when the vitamin is present at low concentrations in a product. These findings increase the

  6. Directly drawn poly(3-hexylthiophene) field-effect transistors by electrohydrodynamic jet printing: improving performance with surface modification.

    Science.gov (United States)

    Jeong, Yong Jin; Lee, Hyungdong; Lee, Byoung-Sun; Park, Seonuk; Yudistira, Hadi Teguh; Choong, Chwee-Lin; Park, Jong-Jin; Park, Chan Eon; Byun, Doyoung

    2014-07-09

    In this study, direct micropatterning lines of poly(3-hexylthiophene) (P3HT) without any polymer binder were prepared by electrohydrodynamic jet printing to form organic field-effect transistors (OFETs). We controlled the dielectric surface by introducing self-assembled monolayers and polymer thin films to investigate the effect of surface modifications on the characteristics of printed P3HT lines and electrical performances of the OFETs. The morphology of the printed P3HT lines depended on the surface energy and type of substrate. The resulting OFETs exhibited high performance on octadecyltrichlorosilane-modified substrates, which was comparable to that of other printed P3HT OFETs. In order to realize the commercialization of the OFETs, we also fabricated a large-area transistor array, including 100 OFETs and low-operating-voltage flexible OFETs.

  7. Application of partial least-squares (PLS) modeling in quantifying drug crystallinity in amorphous solid dispersions.

    Science.gov (United States)

    Rumondor, Alfred C F; Taylor, Lynne S

    2010-10-15

    Among the different experimental methods that can be used to quantify the evolution of drug crystallinity in polymer-containing amorphous solid dispersions, powder X-ray diffractometry (PXRD) is commonly considered as a frontline method. In order to achieve accurate quantification of the percent drug crystallinity in the system, calibration curves have to be constructed using appropriate calibration samples and calculation methods. This can be non-trivial in the case of partially crystalline solid dispersions where the calibration samples must capture the multiphase nature of the systems and the mathematical model must be robust enough to accommodate subtle and not so subtle changes in the diffractograms. The purpose of this study was to compare two different calculation and model-building methods to quantify the proportion of crystalline drug in amorphous solid dispersions containing different ratios of drug and amorphous polymer. The first method involves predicting the % drug crystallinity from the ratio of the area underneath the Bragg peaks to total area of the diffractogram. The second method is multivariate analysis using a Partial Least-Squares (PLS) multivariate regression method. It was found that PLS analysis provided far better accuracy and prediction of % drug crystallinity in the sample. Through the application of PLS, root-mean-squared error of estimation (RMSEE) values of 2.2%, 1.9%, and 4.7% drug crystallinity was achieved for samples containing 25%, 50%, and 75% polymer, respectively, compared to values of 11.2%, 17.0%, and 23.6% for the area model. In addition, construction of a PLS model enables further analysis of the data, including identification of outliers and non-linearity in the data, as well as insight into which factors are most important to correlate PXRD diffractograms with % crystallinity of the drug through analysis of the loadings. Copyright 2010 Elsevier B.V. All rights reserved.

  8. Manipulating hybrid structures of polymer/a-Si for thin film solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Peng, Ying; He, Zhiqun, E-mail: zhqhe@bjtu.edu.cn, E-mail: J.I.B.Wilson@hw.ac.uk; Zhang, Zhi; Liang, Chunjun [Key Laboratory of Luminescence and Optical Information, Ministry of Education, Institute of Optoelectronic Technology, Beijing Jiaotong University, Beijing 100044 (China); Diyaf, Adel; Ivaturi, Aruna; Wilson, John I. B., E-mail: zhqhe@bjtu.edu.cn, E-mail: J.I.B.Wilson@hw.ac.uk [SUPA, School of Engineering and Physical Sciences, Heriot-Watt University, Edinburgh EH14 4AS (United Kingdom)

    2014-03-10

    A series of uniform polymer/amorphous silicon hybrid structures have been fabricated by means of solution-casting for polymer and radio frequency excited plasma enhanced chemical vapour deposition for amorphous silicon (a-Si:H). Poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) functioned as a photoactive donor, while the silicon layer acted as an acceptor. It is found that matching the hole mobility of the polymer to the electron mobility of amorphous silicon is critical to improve the photovoltaic performance from hybrid cells. A three-layer p-i-n structure of ITO/PEDOT:PSS(200 nm)/i-Si(450 nm)/n-Si(200 nm)/Al with a power conversion efficiency of 4.78% under a standard test condition was achieved.

  9. Photoinduced anisotropy in a family of amorphous azobenzene polyesters for optical storage

    DEFF Research Database (Denmark)

    Nedelchev, Lian; Matharu, Avtar S.; Hvilsted, Søren

    2003-01-01

    We investigate parameters associated with optical data storage in a variety of amorphous side-chain azobenzene-containing polyesters denoted as E1aX. The polyesters possess a common cyano-substituted azobenzene chromophore as a side chain, but differ in their main-chain polyester composition....... Seventeen different polymers from the E1aX family divided into four classes, depending on the type of the main-chain substituent (one-, two-, and three-ring aromatic or alicyclic) have been thoroughly investigated. Various parameters characterizing the photoinduced birefringence in these materials...

  10. An Air-Stable DPP-thieno-TTF Copolymer for Single-Material Solar Cell Devices and Field Effect Transistors.

    Science.gov (United States)

    Arumugam, Sasikumar; Cortizo-Lacalle, Diego; Rossbauer, Stephan; Hunter, Simon; Kanibolotsky, Alexander L; Inigo, Anto R; Lane, Paul A; Anthopoulos, Thomas D; Skabara, Peter J

    2015-12-30

    Following an approach developed in our group to incorporate tetrathiafulvalene (TTF) units into conjugated polymeric systems, we have studied a low band gap polymer incorporating TTF as a donor component. This polymer is based on a fused thieno-TTF unit that enables the direct incorporation of the TTF unit into the polymer, and a second comonomer based on the diketopyrrolopyrrole (DPP) molecule. These units represent a donor-acceptor copolymer system, p(DPP-TTF), showing strong absorption in the UV-visible region of the spectrum. An optimized p(DPP-TTF) polymer organic field effect transistor and a single material organic solar cell device showed excellent performance with a hole mobility of up to 5.3 × 10(-2) cm(2)/(V s) and a power conversion efficiency (PCE) of 0.3%, respectively. Bulk heterojunction organic photovoltaic devices of p(DPP-TTF) blended with phenyl-C71-butyric acid methyl ester (PC71BM) exhibited a PCE of 1.8%.

  11. Amorphization of metals by ion implantation and ion beam mixing

    International Nuclear Information System (INIS)

    Rauschenbach, B.; Heera, V.

    1988-01-01

    Amorphous metallic systems can be formed either by high-fluence ion implantation of glassforming species or by irradiation of layered metal systems with inert gas ions. Both techniques and experimental examples are presented. Empirical rules are discussed which predict whether a given system can be transformed into an amorphous phase. Influence of temperature, implantation dose and pre-existing crystalline metal composition on amorphization is considered. Examples are given of the implantation induced amorphous structure, recrystallization and formation of quasicrystalline structures. (author)

  12. Dynamics of hydrogen in hydrogenated amorphous silicon

    Indian Academy of Sciences (India)

    weak (strained) Si–Si bond thereby apparently enhancing the hydrogen diffusion and increasing the light-induced dangling bonds. Keywords. Hydrogenated amorphous silicon; metastable electronic states; hydrogen diffusion. PACS Nos 61.43.Dq; 66.30.-h; 71.23.Cq. 1. Introduction. Hydrogen passivation of dangling bonds ...

  13. Characterization of amorphous hydrogenated carbon films ...

    Indian Academy of Sciences (India)

    Amorphous hydrogenated carbon films (-C:H) on -type (100) silicon wafers were prepared with a middle frequency pulsed unbalanced magnetron sputtering technique (MFPUMST) at different ratios of methane–argon gases. The band characteristics, mechanical properties as well as refractive index were measured by ...

  14. Characterization of amorphous hydrogenated carbon films ...

    Indian Academy of Sciences (India)

    †Key Laboratory of Radiation and Technology of Education Ministry of China, Institute of Nuclear Science and. Technology, Sichuan University, Chengdu 610064, P. R. China. MS received 14 March 2011; revised 29 October 2011. Abstract. Amorphous hydrogenated carbon films (a-C:H) on p-type (100) silicon wafers were ...

  15. Compaction of amorphous iron–boron powder

    DEFF Research Database (Denmark)

    Hendriksen, Peter Vang; Mørup, Steen; Koch, Christian

    1993-01-01

    report on attempts to compact amorphous iron–boron particles prepared by chemical reduction of Fe(II) ions in aqueous solution by NaBH4 (Ref. 2). The particles prepared in this way are pyrophoric, but can be passivated. The small particle size (10–100 nm), characteristic of this preparation technique...

  16. Trap level spectroscopy in amorphous semiconductors

    CERN Document Server

    Mikla, Victor V

    2010-01-01

    Although amorphous semiconductors have been studied for over four decades, many of their properties are not fully understood. This book discusses not only the most common spectroscopic techniques but also describes their advantages and disadvantages.Provides information on the most used spectroscopic techniquesDiscusses the advantages and disadvantages of each technique

  17. Film adhesion in amorphous silicon solar cells

    Indian Academy of Sciences (India)

    TECS

    Abstract. A major issue encountered during fabrication of triple junction a-Si solar cells on polyimide sub- strates is the adhesion of the solar cell thin films to the substrates. Here, we present our study of film adhesion in amorphous silicon solar cells made on different polyimide substrates (Kapton VN, Upilex-S and ...

  18. Structural morphology of amorphous conducting carbon film

    Indian Academy of Sciences (India)

    Amorphous conducting carbon films deposited over quartz substrates were analysed using X-ray diffraction and AFM technique. X-ray diffraction data reveal disorder and roughness in the plane of graphene sheet as compared to that of graphite. This roughness increases with decrease in preparation temperature. The AFM ...

  19. Film adhesion in amorphous silicon solar cells

    Indian Academy of Sciences (India)

    A major issue encountered during fabrication of triple junction -Si solar cells on polyimide substrates is the adhesion of the solar cell thin films to the substrates. Here, we present our study of film adhesion in amorphous silicon solar cells made on different polyimide substrates (Kapton VN, Upilex-S and Gouldflex), and the ...

  20. Dynamics of hydrogen in hydrogenated amorphous silicon

    Indian Academy of Sciences (India)

    c0, c being the instantaneous concentration at a local point and c0, the average concentration of hydrogen in the hydrogenated amorphous silicon. If the system is both incompressible and isotropic, the change in Helmholtz free energy due to fluctuations in the local concentration of hydrogen is given as. 122. Pramana – J.

  1. Radiative recombination of excitons in amorphous semiconductors

    International Nuclear Information System (INIS)

    Singh, Jai

    2005-01-01

    A theory for calculating the radiative lifetime of excitons in amorphous semiconductors is presented. Four possibilities of excitonic radiative recombination are considered and the corresponding rates are derived at thermal equilibrium. The radiative lifetime is calculated from the inverse of the maximum rate for all the four possibilities. Results agree very well with experiments

  2. Neutron diffraction studies of amorphous solids

    International Nuclear Information System (INIS)

    Wright, A.C.

    1983-01-01

    A brief survey is presented of the role of neutron diffraction in structural studies of amorphous solids. The inherent limitations of the diffraction technique are discussed, together with modern instrumentation and methods for separating individual component correlation functions. An introduction is given to the use of modelling and the extraction of structural parameters from experimental data. (author)

  3. Amorphous calcium carbonate particles form coral skeletons

    Science.gov (United States)

    Mass, Tali; Giuffre, Anthony J.; Sun, Chang-Yu; Stifler, Cayla A.; Frazier, Matthew J.; Neder, Maayan; Tamura, Nobumichi; Stan, Camelia V.; Marcus, Matthew A.; Gilbert, Pupa U. P. A.

    2017-09-01

    Do corals form their skeletons by precipitation from solution or by attachment of amorphous precursor particles as observed in other minerals and biominerals? The classical model assumes precipitation in contrast with observed “vital effects,” that is, deviations from elemental and isotopic compositions at thermodynamic equilibrium. Here, we show direct spectromicroscopy evidence in Stylophora pistillata corals that two amorphous precursors exist, one hydrated and one anhydrous amorphous calcium carbonate (ACC); that these are formed in the tissue as 400-nm particles; and that they attach to the surface of coral skeletons, remain amorphous for hours, and finally, crystallize into aragonite (CaCO3). We show in both coral and synthetic aragonite spherulites that crystal growth by attachment of ACC particles is more than 100 times faster than ion-by-ion growth from solution. Fast growth provides a distinct physiological advantage to corals in the rigors of the reef, a crowded and fiercely competitive ecosystem. Corals are affected by warming-induced bleaching and postmortem dissolution, but the finding here that ACC particles are formed inside tissue may make coral skeleton formation less susceptible to ocean acidification than previously assumed. If this is how other corals form their skeletons, perhaps this is how a few corals survived past CO2 increases, such as the Paleocene-Eocene Thermal Maximum that occurred 56 Mya.

  4. Amorphous track models: A numerical comparison study

    DEFF Research Database (Denmark)

    Greilich, Steffen; Grzanka, L.; Bassler, N.

    2010-01-01

    We present an open-source code library for amorphous track modelling which is suppose to faciliate the application and numerical comparability as well as serve as a frame-work for the implementation of new models. We show an example of using the library indicating the choice of submodels has a si...

  5. The Electronic Structure of Amorphous Carbon Nanodots.

    Science.gov (United States)

    Margraf, Johannes T; Strauss, Volker; Guldi, Dirk M; Clark, Timothy

    2015-06-18

    We have studied hydrogen-passivated amorphous carbon nanostructures with semiempirical molecular orbital theory in order to provide an understanding of the factors that affect their electronic properties. Amorphous structures were first constructed using periodic calculations in a melt/quench protocol. Pure periodic amorphous carbon structures and their counterparts doped with nitrogen and/or oxygen feature large electronic band gaps. Surprisingly, descriptors such as the elemental composition and the number of sp(3)-atoms only influence the electronic structure weakly. Instead, the exact topology of the sp(2)-network in terms of effective conjugation defines the band gap. Amorphous carbon nanodots of different structures and sizes were cut out of the periodic structures. Our calculations predict the occurrence of localized electronic surface states, which give rise to interesting effects such as amphoteric reactivity and predicted optical band gaps in the near-UV/visible range. Optical and electronic gaps display a dependence on particle size similar to that of inorganic colloidal quantum dots.

  6. Plasma deposition of amorphous metal alloys

    Science.gov (United States)

    Hays, Auda K.

    1986-01-01

    Amorphous metal alloy coatings are plasma-deposited by dissociation of vapors of organometallic compounds and metalloid hydrides in the presence of a reducing gas, using a glow discharge. Tetracarbonylnickel, phosphine, and hydrogen constitute a typical reaction mixture of the invention, yielding a NiPC alloy.

  7. Fringe field effects in small rings of large acceptance

    Directory of Open Access Journals (Sweden)

    Martin Berz

    2000-12-01

    Full Text Available Recently there has been renewed interest in the influence of fringe fields on particle dynamics, due to studies that revealed their importance in some cases, as, for example, the proposed Neutrino Factory and muon colliders. In this paper, we present a systematic study of generic fringe field effects. Using as an example a lattice of the proposed Neutrino Factory, we show that fringe fields influence the dynamics of particles at all orders, starting with the linear motion. It is found that the widely used sharp cutoff approximation leads to divergences regardless of the specific fall-off shape of the fields. The results suggest that a careful consideration of fringe field effects in the design stage of small machines for large emittances is always recommended.

  8. Electric-field effects in optically generated spin transport

    Energy Technology Data Exchange (ETDEWEB)

    Miah, M. Idrish [Nanoscale Science and Technology Centre and School of Biomolecular and Physical Sciences, Griffith University, Nathan, Brisbane, QLD 4111 (Australia); Department of Physics, University of Chittagong, Chittagong 4331 (Bangladesh)], E-mail: m.miah@griffith.edu.au

    2009-05-25

    Transport of spin-polarized electrons in semiconductors is studied experimentally. Spins are generated by optical excitation because of the selection rules governing optical transitions from heavy-hole and light-hole states to conduction-band states. Experiments designed for the control of spins in semiconductors investigate the bias-dependent spin transport process and detect the spin-polarized electrons during transport. A strong bias dependence is observed. The electric-field effects on the spin-polarized electron transport are also found to be depended on the excitation photon energy and temperature. Based on a field-dependent spin relaxation mechanism, the electric-field effects in the transport process are discussed.

  9. Graphene-based field-effect transistor biosensors

    Science.gov (United States)

    Chen; , Junhong; Mao, Shun; Lu, Ganhua

    2017-06-14

    The disclosure provides a field-effect transistor (FET)-based biosensor and uses thereof. In particular, to FET-based biosensors using thermally reduced graphene-based sheets as a conducting channel decorated with nanoparticle-biomolecule conjugates. The present disclosure also relates to FET-based biosensors using metal nitride/graphene hybrid sheets. The disclosure provides a method for detecting a target biomolecule in a sample using the FET-based biosensor described herein.

  10. Antimocrobial Polymer

    Energy Technology Data Exchange (ETDEWEB)

    McDonald, William F. (Utica, OH); Huang, Zhi-Heng (Walnut Creek, CA); Wright, Stacy C. (Columbus, GA)

    2005-09-06

    A polymeric composition having antimicrobial properties and a process for rendering the surface of a substrate antimicrobial are disclosed. The composition comprises a crosslinked chemical combination of (i) a polymer having amino group-containing side chains along a backbone forming the polymer, (ii) an antimicrobial agent selected from quaternary ammonium compounds, gentian violet compounds, substituted or unsubstituted phenols, biguanide compounds, iodine compounds, and mixtures thereof, and (iii) a crosslinking agent containing functional groups capable of reacting with the amino groups. In one embodiment, the polymer is a polyamide formed from a maleic anhydride or maleic acid ester monomer and alkylamines thereby producing a polyamide having amino substituted alkyl chains on one side of the polyamide backbone; the crosslinking agent is a phosphine having the general formula (A)3P wherein A is hydroxyalkyl; and the antimicrobial agent is chlorhexidine, dimethylchlorophenol, cetyl pyridinium chloride, gentian violet, triclosan, thymol, iodine, and mixtures thereof.

  11. New Material Transistor with Record-High Field-Effect Mobility among Wide-Band-Gap Semiconductors.

    Science.gov (United States)

    Shih, Cheng Wei; Chin, Albert

    2016-08-03

    At an ultrathin 5 nm, we report a new high-mobility tin oxide (SnO2) metal-oxide-semiconductor field-effect transistor (MOSFET) exhibiting extremely high field-effect mobility values of 279 and 255 cm(2)/V-s at 145 and 205 °C, respectively. These values are the highest reported mobility values among all wide-band-gap semiconductors of GaN, SiC, and metal-oxide MOSFETs, and they also exceed those of silicon devices at the aforementioned elevated temperatures. For the first time among existing semiconductor transistors, a new device physical phenomenon of a higher mobility value was measured at 45-205 °C than at 25 °C, which is due to the lower optical phonon scattering by the large SnO2 phonon energy. Moreover, the high on-current/off-current of 4 × 10(6) and the positive threshold voltage of 0.14 V at 25 °C are significantly better than those of a graphene transistor. This wide-band-gap SnO2 MOSFET exhibits high mobility in a 25-205 °C temperature range, a wide operating voltage of 1.5-20 V, and the ability to form on an amorphous substrate, rendering it an ideal candidate for multifunctional low-power integrated circuit (IC), display, and brain-mimicking three-dimensional IC applications.

  12. Interdigitated Extended Gate Field Effect Transistor Without Reference Electrode

    Science.gov (United States)

    Ali, Ghusoon M.

    2017-02-01

    An interdigitated extended gate field effect transistor (IEGFET) has been proposed as a modified pH sensor structure of an extended gate field effect transistor (EGFET). The reference electrode and the extended gate in the conventional device have been replaced by a single interdigitated extended gate. A metal-semiconductor-metal interdigitated extended gate containing two multi-finger Ni electrodes based on zinc oxide (ZnO) thin film as a pH-sensitive membrane. ZnO thin film was grown on a p-type Si (100) substrate by the sol-gel technique. The fabricated extended gate is connected to a commercial metal-oxide-semiconductor field-effect transistor device in CD4007UB. The experimental data show that this structure has real time and linear pH voltage and current sensitivities in a concentration range between pH 4 and 11. The voltage and current sensitivities are found to be about 22.4 mV/pH and 45 μA/pH, respectively. Reference electrode elimination makes the IEGFET device simple to fabricate, easy to carry out the measurements, needing a small volume of solution to test and suitable for disposable biosensor applications. Furthermore, this uncomplicated structure could be extended to fabricate multiple ions microsensors and lab-on-chip devices.

  13. Organic field-effect transistors using single crystals.

    Science.gov (United States)

    Hasegawa, Tatsuo; Takeya, Jun

    2009-04-01

    Organic field-effect transistors using small-molecule organic single crystals are developed to investigate fundamental aspects of organic thin-film transistors that have been widely studied for possible future markets for 'plastic electronics'. In reviewing the physics and chemistry of single-crystal organic field-effect transistors (SC-OFETs), the nature of intrinsic charge dynamics is elucidated for the carriers induced at the single crystal surfaces of molecular semiconductors. Materials for SC-OFETs are first reviewed with descriptions of the fabrication methods and the field-effect characteristics. In particular, a benchmark carrier mobility of 20-40 cm 2 Vs -1 , achieved with thin platelets of rubrene single crystals, demonstrates the significance of the SC-OFETs and clarifies material limitations for organic devices. In the latter part of this review, we discuss the physics of microscopic charge transport by using SC-OFETs at metal/semiconductor contacts and along semiconductor/insulator interfaces. Most importantly, Hall effect and electron spin resonance (ESR) measurements reveal that interface charge transport in molecular semiconductors is properly described in terms of band transport and localization by charge traps.

  14. Organic field-effect transistors using single crystals

    Directory of Open Access Journals (Sweden)

    Tatsuo Hasegawa and Jun Takeya

    2009-01-01

    Full Text Available Organic field-effect transistors using small-molecule organic single crystals are developed to investigate fundamental aspects of organic thin-film transistors that have been widely studied for possible future markets for 'plastic electronics'. In reviewing the physics and chemistry of single-crystal organic field-effect transistors (SC-OFETs, the nature of intrinsic charge dynamics is elucidated for the carriers induced at the single crystal surfaces of molecular semiconductors. Materials for SC-OFETs are first reviewed with descriptions of the fabrication methods and the field-effect characteristics. In particular, a benchmark carrier mobility of 20–40 cm2 Vs−1, achieved with thin platelets of rubrene single crystals, demonstrates the significance of the SC-OFETs and clarifies material limitations for organic devices. In the latter part of this review, we discuss the physics of microscopic charge transport by using SC-OFETs at metal/semiconductor contacts and along semiconductor/insulator interfaces. Most importantly, Hall effect and electron spin resonance (ESR measurements reveal that interface charge transport in molecular semiconductors is properly described in terms of band transport and localization by charge traps.

  15. Lead iodide perovskite light-emitting field-effect transistor

    Science.gov (United States)

    Chin, Xin Yu; Cortecchia, Daniele; Yin, Jun; Bruno, Annalisa; Soci, Cesare

    2015-06-01

    Despite the widespread use of solution-processable hybrid organic-inorganic perovskites in photovoltaic and light-emitting applications, determination of their intrinsic charge transport parameters has been elusive due to the variability of film preparation and history-dependent device performance. Here we show that screening effects associated to ionic transport can be effectively eliminated by lowering the operating temperature of methylammonium lead iodide perovskite (CH3NH3PbI3) field-effect transistors. Field-effect carrier mobility is found to increase by almost two orders of magnitude below 200 K, consistent with phonon scattering-limited transport. Under balanced ambipolar carrier injection, gate-dependent electroluminescence is also observed from the transistor channel, with spectra revealing the tetragonal to orthorhombic phase transition. This demonstration of CH3NH3PbI3 light-emitting field-effect transistors provides intrinsic transport parameters to guide materials and solar cell optimization, and will drive the development of new electro-optic device concepts, such as gated light-emitting diodes and lasers operating at room temperature.

  16. Crystallization of biogenic hydrous amorphous silica

    Science.gov (United States)

    Kyono, A.; Yokooji, M.; Chiba, T.; Tamura, T.; Tuji, A.

    2017-12-01

    Diatom, Nitzschia cf. frustulum, collected from Lake Yogo, Siga prefecture, Japan was cultured in laboratory. Organic components of the diatom cell were removed by washing with acetone and sodium hypochlorite. The remaining frustules were studied by SEM-EDX, FTIR spectroscopy, and synchrotron X-ray diffraction. The results showed that the spindle-shaped morphology of diatom frustule was composed of hydrous amorphous silica. Pressure induced phase transformation of the diatom frustule was investigated by in situ Raman spectroscopic analysis. With exposure to 0.3 GPa at 100 oC, Raman band corresponding to quartz occurred at ν = 465 cm-1. In addition, Raman bands known as a characteristic Raman pattern of moganite was also observed at 501 cm-1. From the integral ratio of Raman bands, the moganite content in the probed area was estimated to be approximately 50 wt%. With the pressure and temperature effect, the initial morphology of diatom frustule was completely lost and totally changed to a characteristic spherical particle with a diameter of about 2 mm. With keeping the compression of 5.7 GPa at 100 oC, a Raman band assignable to coesite appeared at 538 cm-1. That is, with the compression and heating, the hydrous amorphous silica can be readily crystallized into quartz, moganite, and coesite. The first-principles calculations revealed that a disiloxane molecule stabilized in a trans configuration is twisted 60o and changed into the cis configuration with a close approach of water molecule. It is therefore a reasonable assumption that during crystallization of hydrous amorphous silica, the Si-O-Si bridging unit with the cis configuration would survive as a structural defect and then crystallized into moganite by keeping the geometry. This hypothesis is adaptable to the phase transformation from hydrous amorphous silica to coesite as well, because coesite has the four-membered rings and easily formed from the hydrous amorphous silica under high pressure and high

  17. Polymer electronics

    CERN Document Server

    Geoghegan, Mark

    2013-01-01

    Polymer electronics is the science behind many important new developments in technology, such as the flexible electronic display (e-ink) and many new developments in transistor technology. Solar cells, light-emitting diodes, and transistors are all areas where plastic electronics is likely to, or is already having, a serious impact on our daily lives. With polymer transistors and light-emitting diodes now being commercialised, there is a clear need for a pedagogic text thatdiscusses the subject in a clear and concise fashion suitable for senior undergraduate and graduate students. The content

  18. First-Principles Prediction of Densities of Amorphous Materials: The Case of Amorphous Silicon

    Science.gov (United States)

    Furukawa, Yoritaka; Matsushita, Yu-ichiro

    2018-02-01

    A novel approach to predict the atomic densities of amorphous materials is explored on the basis of Car-Parrinello molecular dynamics (CPMD) in density functional theory. Despite the determination of the atomic density of matter being crucial in understanding its physical properties, no first-principles method has ever been proposed for amorphous materials until now. We have extended the conventional method for crystalline materials in a natural manner and pointed out the importance of the canonical ensemble of the total energy in the determination of the atomic densities of amorphous materials. To take into account the canonical distribution of the total energy, we generate multiple amorphous structures with several different volumes by CPMD simulations and average the total energies at each volume. The density is then determined as the one that minimizes the averaged total energy. In this study, this approach is implemented for amorphous silicon (a-Si) to demonstrate its validity, and we have determined the density of a-Si to be 4.1% lower and its bulk modulus to be 28 GPa smaller than those of the crystal, which are in good agreement with experiments. We have also confirmed that generating samples through classical molecular dynamics simulations produces a comparable result. The findings suggest that the presented method is applicable to other amorphous systems, including those for which experimental knowledge is lacking.

  19. Geminate free radical processes and magnetic field effects

    International Nuclear Information System (INIS)

    Eveson, Robert W.

    2000-01-01

    This thesis is concerned with the study of the dynamics of radical pair recombination reactions in solution by flash photolysis Electron Spin Resonance (ESR) and the influence of low static external magnetic fields upon them (MFE). An outline of the concepts of ESR is presented, followed by the theories of Chemically Induced Dynamic Electron Polarisation (CIDEP) of transient radical pairs. This is then followed by a brief review of the flash photolysis ESR apparatus and application of the Bloch equations to solve the equations of time-resolved ESR. Completing the theory section is an overview of the mechanisms by which magnetic fields alter the course of a geminate radical pair reaction in solution. Experimental CIDEP observations of the radical pair produced on photolysis of 1,3-dihydroxypropanone are simulated using polarisation theory and applied to a random-walk diffusion model to find, for the first time, the geminate reaction probability in solutions of varying viscosity. CIDEP spectra of the radical pair formed on photolysis of hydroxypropanone in contrast are not accounted for by current polarisation theory. The discrepancy is due to moderately fast relaxation of the acyl radical, CH 3 CO·, which alters the relative intensities in the ST 0 RPM pattern of the counter radical. Calculations taking into account this now provide an adequate basis for simulation of the spectrum. This method also, in principle, represents a new method for the measurement of phase relaxation times. Concluding the ESR work is a CIDEP study of 2,4,6-trimethylbenzoyl diphenylphosphine oxide. Unusual spin polarisation phenomena are found. The time-resolved optical absorption spectroscopy technique used for detecting low magnetic field effects on neutral radical pair reactions is described. Various improvements to the experiment are discussed which result in the observation of the low field effect for a neutral radical pair produced by Norrish type II chemistry. This is followed by an

  20. Enzyme-polymer composites with high biocatalytic activity and stability

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jungbae; Kosto, Timothy J.; Manimala, Joseph C.; Nauman, E B.; Dordick, Jonathan S.

    2004-08-22

    We have applied vacuum-spraying and electrospinning to incorporate an enzyme into a polymer matrix, creating a novel and highly active biocatalytic composite. As a unique technical approach, enzymes were co-dissolved in toluene with polymers, and the solvent was then rapidly removed by injecting the mixture into a vacuum chamber or by electrospinning. Subsequent crosslinking of the enzyme with glutaraldehyde resulted in stable entrapped enzyme within the polymeric matrices. For example, an amorphous composite of alpha-chymotrypsin and polyethylene showed no significant loss of enzymatic activity in aqueous buffer for one month. Nanofibers of alpha-chymotrypsin and polystyrene also showed no decrease in activity for more than two weeks. The normalized activity of amorphous composite in organic solvents was 3-13 times higher than that of native alpha-chymotrypsin. The activity of nanofibers was 5-7 times higher than that of amorphous composite in aqueous buffer solution. The composites of alpha-chymotrypsin and polymers demonstrate the feasibility of obtaining a wide variety of active and stable biocatalytic materials with many combinations of enzymes and polymers.

  1. Properties of polymer light-emitting transistors with Ag-nanowire source/drain electrodes fabricated on polymer substrate

    Energy Technology Data Exchange (ETDEWEB)

    Hiraoka, Koichi; Kusumoto, Yusuke; Ikezoe, Ikuya; Kajii, Hirotake, E-mail: kajii@oled.eei.eng.osaka-u.ac.jp; Ohmori, Yutaka

    2014-03-03

    The properties of polymer light-emitting transistors with Ag-nanowire (AgNW) source/drain electrodes fabricated on a polymer substrate are investigated. Organic field-effect transistors (OFETs) based on poly(9,9-dioctylfluorene-co-benzothiadiazole) (F8BT) with AgNW source/drain electrodes exhibit ambipolar characteristics. For an ambipolar F8BT OFET, yellow-green light emission is observed. The maximum external quantum efficiency is 0.6%. We demonstrate the possibility of producing flexible polymer light-emitting transistors using AgNW electrodes. - Highlights: • Fluorene-type organic field-effect transistors (OFETs) are investigated. • We use Ag-nanowire (AgNW) source/drain electrodes in the OFETs. • These OFETs exhibit ambipolar and light-emitting characteristics. • The maximum external quantum efficiency is 0.6%. • We demonstrate flexible polymer light-emitting transistors using AgNW electrodes.

  2. Reducing burn-in voltage loss in polymer solar cells by increasing the polymer crystallinity

    KAUST Repository

    Heumueller, Thomas

    2014-08-01

    In order to commercialize polymer solar cells, the fast initial performance losses present in many high efficiency materials will have to be managed. This burn-in degradation is caused by light-induced traps and its characteristics depend on which polymer is used. We show that the light-induced traps are in the bulk of the active layer and we find a direct correlation between their presence and the open-circuit voltage loss in devices made with amorphous polymers. Solar cells made with crystalline polymers do not show characteristic open circuit voltage losses, even though light-induced traps are also present in these devices. This indicates that crystalline materials are more resistant against the influence of traps on device performance. Recent work on crystalline materials has shown there is an energetic driving force for charge carriers to leave amorphous, mixed regions of bulk heterojunctions, and charges are dominantly transported in pure, ordered phases. This energetic landscape allows efficient charge generation as well as extraction and also may benefit the stability against light-induced traps. This journal is © the Partner Organisations 2014.

  3. Megavoltage imaging with a large-area, flat-panel, amorphous silicon imager

    International Nuclear Information System (INIS)

    Antonuk, Larry E.; Yorkston, John; Huang Weidong; Sandler, Howard; Siewerdsen, Jeffrey H.; El-Mohri, Youcef

    1996-01-01

    Purpose: The creation of the first large-area, amorphous silicon megavoltage imager is reported. The imager is an engineering prototype built to serve as a stepping stone toward the creation of a future clinical prototype. The engineering prototype is described and various images demonstrating its properties are shown including the first reported patient image acquired with such an amorphous silicon imaging device. Specific limitations in the engineering prototype are reviewed and potential advantages of future, more optimized imagers of this type are presented. Methods and Materials: The imager is based on a two-dimensional, pixelated array containing amorphous silicon field-effect transistors and photodiode sensors which are deposited on a thin glass substrate. The array has a 512 x 560-pixel format and a pixel pitch of 450 μm giving an imaging area of ∼23 x 25 cm 2 . The array is used in conjunction with an overlying metal plate/phosphor screen converter as well as an electronic acquisition system. Images were acquired fluoroscopically using a megavoltage treatment machine. Results: Array and digitized film images of a variety of anthropomorphic phantoms and of a human subject are presented and compared. The information content of the array images generally appears to be at least as great as that of the digitized film images. Conclusion: Despite a variety of severe limitations in the engineering prototype, including many array defects, a relatively slow and noisy acquisition system, and the lack of a means to generate images in a radiographic manner, the prototype nevertheless generated clinically useful information. The general properties of these amorphous silicon arrays, along with the quality of the images provided by the engineering prototype, strongly suggest that such arrays could eventually form the basis of a new imaging technology for radiotherapy localization and verification. The development of a clinically useful prototype offering high

  4. An entropy spring model for the Young's modulus change of biodegradable polymers during biodegradation.

    Science.gov (United States)

    Wang, Ying; Han, Xiaoxiao; Pan, Jingzhe; Sinka, Csaba

    2010-01-01

    This paper presents a model for the change in Young's modulus of biodegradable polymers due to hydrolysis cleavage of the polymer chains. The model is based on the entropy spring theory for amorphous polymers. It is assumed that isolated polymer chain cleavage and very short polymer chains do not affect the entropy change in a linear biodegradable polymer during its deformation. It is then possible to relate the Young's modulus to the average molecular weight in a computer simulated hydrolysis process of polymer chain sessions. The experimental data obtained by Tsuji [Tsuji, H., 2002. Autocatalytic hydrolysis of amorphous-made polylactides: Effects of L-lactide content, tacticity, and enantiomeric polymer blending. Polymers 43, 1789-1796] for poly(L-lactic acid) and poly(D-lactic acid) are examined using the model. It is shown that the model can provide a common thread through Tsuji's experimental data. A further numerical case study demonstrates that the Young's modulus obtained using very thin samples, such as those obtained by Tsuji, cannot be directly used to calculate the load carried by a device made of the same polymer but of various thicknesses. This is because the Young's modulus varies significantly in a biodegradable device due to the heterogeneous nature of the hydrolysis reaction. The governing equations for biodegradation and the relation between the Young's modulus and average molecular weight can be combined to calculate the load transfer from a degrading device to a healing bone.

  5. Composite Polymer Electrolytes: Nanoparticles Affect Structure and Properties

    Directory of Open Access Journals (Sweden)

    Wei Wang

    2016-11-01

    Full Text Available Composite polymer electrolytes (CPEs can significantly improve the performance in electrochemical devices such as lithium-ion batteries. This review summarizes property/performance relationships in the case where nanoparticles are introduced to polymer electrolytes. It is the aim of this review to provide a knowledge network that elucidates the role of nano-additives in the CPEs. Central to the discussion is the impact on the CPE performance of properties such as crystalline/amorphous structure, dielectric behavior, and interactions within the CPE. The amorphous domains of semi-crystalline polymer facilitate the ion transport, while an enhanced mobility of polymer chains contributes to high ionic conductivity. Dielectric properties reflect the relaxation behavior of polymer chains as an important factor in ion conduction. Further, the dielectric constant (ε determines the capability of the polymer to dissolve salt. The atom/ion/nanoparticle interactions within CPEs suggest ways to enhance the CPE conductivity by generating more free lithium ions. Certain properties can be improved simultaneously by nanoparticle addition in order to optimize the overall performance of the electrolyte. The effects of nano-additives on thermal and mechanical properties of CPEs are also presented in order to evaluate the electrolyte competence for lithium-ion battery applications.

  6. Dynamics and thermodynamics of polymer glasses.

    Science.gov (United States)

    Cangialosi, D

    2014-04-16

    The fate of matter when decreasing the temperature at constant pressure is that of passing from gas to liquid and, subsequently, from liquid to crystal. However, a class of materials can exist in an amorphous phase below the melting temperature. On cooling such materials, a glass is formed; that is, a material with the rigidity of a solid but exhibiting no long-range order. The study of the thermodynamics and dynamics of glass-forming systems is the subject of continuous research. Within the wide variety of glass formers, an important sub-class is represented by glass forming polymers. The presence of chain connectivity and, in some cases, conformational disorder are unfavourable factors from the point of view of crystallization. Furthermore, many of them, such as amorphous thermoplastics, thermosets and rubbers, are widely employed in many applications. In this review, the peculiarities of the thermodynamics and dynamics of glass-forming polymers are discussed, with particular emphasis on those topics currently the subject of debate. In particular, the following aspects will be reviewed in the present work: (i) the connection between the pronounced slowing down of glassy dynamics on cooling towards the glass transition temperature (Tg) and the thermodynamics; and, (ii) the fate of the dynamics and thermodynamics below Tg. Both aspects are reviewed in light of the possible presence of a singularity at a finite temperature with diverging relaxation time and zero configurational entropy. In this context, the specificity of glass-forming polymers is emphasized.

  7. Conducting Polymers

    Indian Academy of Sciences (India)

    backbone (by the process of doping) and make them electrically. Conducting Polymers. From a Laboratory Curiosity to the Market Place. S Ramakrishnan ..... switching occurs between transparent yellow and green in less than. 100ms. Thus, while these materials are yet to achieve the set target. (in terms of their life cycle) ...

  8. Conducting Polymers

    Indian Academy of Sciences (India)

    ized the plastics industry by providing a route to polypropylene. (Zeigler and Natta jointly won the. Nobel Prize in Chemistry in 1963 for their discovery.) ... transport of charge in these systems can be understood in a simple fashion, by causing the imine and amine nitrogens to exchange places along the polymer backbone (in ...

  9. Conducting Polymers

    Indian Academy of Sciences (India)

    the plastics industry by providing a route to polypropylene. (Zeigler and Natta jointly won the Nobel Prize in chemistry in 1963 for their discovery.) ... these systems can be understood in a simple fashion, by causing the imine and amine nitrogens to exchange places along the polymer backbone (in protonated emeraldinel.

  10. Conducting Polymers

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 16; Issue 12. Conducting Polymers - From a Laboratory Curiosity to the Market Place. S Ramakrishnan. Volume 16 Issue 12 December 2011 pp 1254-1265. Fulltext. Click here to view fulltext PDF. Permanent link:

  11. Polymer solutions

    Science.gov (United States)

    Krawczyk, Gerhard Erich [Bremen, DE; Miller, Kevin Michael [West Dundee, IL

    2011-07-26

    There is provided a method of making a polymer solution comprising polymerizing one or more monomer in a solvent, wherein said monomer comprises one or more ethylenically unsaturated monomer that is a multi-functional Michael donor, and wherein said solvent comprises 40% or more by weight, based on the weight of said solvent, one or more multi-functional Michael donor.

  12. Polymer physics

    CERN Document Server

    Gedde, Ulf W

    1999-01-01

    This book is the result of my teaching efforts during the last ten years at the Royal Institute of Technology. The purpose is to present the subject of polymer physics for undergraduate and graduate students, to focus the fundamental aspects of the subject and to show the link between experiments and theory. The intention is not to present a compilation of the currently available literature on the subject. Very few reference citations have thus been made. Each chapter has essentially the same structure: starling with an introduction, continuing with the actual subject, summarizing the chapter in 30D-500 words, and finally presenting problems and a list of relevant references for the reader. The solutions to the problems presented in Chapters 1-12 are given in Chapter 13. The theme of the book is essentially polymer science, with the exclusion of that part dealing directly with chemical reactions. The fundamentals in polymer science, including some basic polymer chemistry, are presented as an introduction in t...

  13. Supramolecular polymers

    National Research Council Canada - National Science Library

    Ciferri, A

    2000-01-01

    ... to the new class of self-assembled polymers that undergo reversible growth by the formation of noncovalent bonds. This class (Part II) is wider than expected: not only mainchain assemblies of hydrogen-bonded repeating units, but also planar organization of S-layer proteins, micellar and related three-dimensional structures of blo...

  14. Effects of high-energy heavy ions on amorphous materials

    International Nuclear Information System (INIS)

    Klaumuenzer, S.; Gutzmann, A.

    1994-01-01

    In matter fast ions deposit their kinetic energy mainly via the nuclear energy loss and via the electronic energy loss. The former denotes the process of transfer of kinetic energy to the material atoms as a whole whereas the latter leads to excited and/or ionized target atoms. With the advent of the mega volt implanters in science and technology the component of the electronic energy loss grows in its importance. Reviewing recent experiments in the ion energy range of 100 to 1000 MeV it is shown that in all amorphous materials (polymer glasses, dielectric, metallic glasses) atomic rearrangements are released by electronic excitations. In the low-fluence region particle track formation is the most important process whereas in the high-fluence region ion-beam-induced plastic deformation causes macroscopically visible specimen deformations. Finally, it is shown that the latter effects are also of importance in the field of implantation of ions of several MeV. (author). 60 refs, 3 figs, 2 tabs

  15. Lifetime of Poly(triaryl amine) Based Organic Field Effect Transistors under Different Environmental Conditions

    Science.gov (United States)

    Lau, Tobias; Lorenz, Enno; Koyuncu, Metin

    2013-04-01

    Characterization of reliability and lifetime is a key issue on the way to commercialization of products based on organic electronics. Prediction of the lifetime requires the understanding of failure mechanisms and the circumstances leading to failure. In this work the stability of poly(triaryl amine) (PTAA) based organic field effect transistors (OFETs) on a poly(ethylene naphthalate) (PEN) substrate is investigated under environmental stressing. PTAA is known to form amorphous thin films after spin coating and to be air stable for extended periods of time. This inherent air stability makes it a good candidate for testing of environmental influences. The samples were electrically characterized regularly between storage cycles at 85 °C and 85 °C/85% relative humidity (RH). Samples stored under dry atmosphere and inert gas were used as reference. More than 1700 OFETs were produced in multiple batches and measured using an automated measurement system to collect statistically significant data. Circuit-relevant OFET parameters such as on- and off-current, mobility, threshold voltage and gate leakage current were extracted applying a thin film transistor (TFT) device model to the measured transfer and output curves. The threshold voltage is found to be the most sensitive parameter especially for the samples stored at 85 °C. The effect of storage under 85 °C/85%RH is observed to be comparably small. Fourier transform infrared (FT-IR) measurements of the aged OFET samples indicate a correlation between the shift of the electrical parameters and the appearance of carbonyl groups in the dielectric layer of the devices. Possible degradation mechanisms are discussed based on this observation.

  16. Amorphous-crystalline transition in thermoelectric NbO2

    International Nuclear Information System (INIS)

    Music, Denis; Chen, Yen-Ting; Bliem, Pascal; Geyer, Richard W

    2015-01-01

    Density functional theory was employed to design enhanced amorphous NbO 2 thermoelectrics. The covalent-ionic nature of Nb–O bonding is identical in amorphous NbO 2 and its crystalline counterpart. However, the Anderson localisation occurs in amorphous NbO 2 , which may affect the transport properties. We calculate a multifold increase in the absolute Seebeck coefficient for the amorphous state. These predictions were critically appraised by measuring the Seebeck coefficient of sputtered amorphous and crystalline NbO 2 thin films with the identical short-range order. The first-order phase transition occurs at approximately 550 °C, but amorphous NbO 2 possesses enhanced transport properties at all temperatures. Amorphous NbO 2 , reaching  −173 μV K −1 , exhibits up to a 29% larger absolute Seebeck coefficient value, thereby validating the predictions. (paper)

  17. Importance of in vitro dissolution conditions for the in vivo predictability of an amorphous solid dispersion containing a pH-sensitive carrier.

    Science.gov (United States)

    Wendelboe, Johan; Knopp, Matthias Manne; Khan, Fauzan; Chourak, Nabil; Rades, Thomas; Holm, René

    2017-10-05

    The present study investigated the influence of in vitro dissolution conditions on the in vivo predictability of an amorphous solid dispersion of celecoxib (CCX) in the pH-sensitive polymer Eudragit ® S 100. Different doses of a 25:75w/w% CCX:Eudragit ® S 100 amorphous solid dispersion (CCX:EUD) were investigated. During in vitro dissolution a significant effect of the pH of the dissolution media on the release of CCX was observed. In fasted state simulated intestinal fluid (FaSSIF) pH 6.5, the release of CCX from the amorphous solid dispersion was comparable to that of crystalline CCX and lower than that of amorphous CCX whereas in FaSSIF pH 7.4, the release was significantly increased compared to both crystalline and amorphous CCX. With a 3-fold increase in the exposure of CCX:EUD compared to crystaline CCX. The in vivo data also suggested that Eudragit ® S 100 was suitable as a carrier in amorphous solid dispersions of CCX. In vitro-in vivo correlation demonstrated that the in vitro data obtained in FaSSIF pH 7.4 was more predictive for the in vivo performance than that obtained in FaSSIF pH 6.5. Consequently, the findings of this study underline that when predicting the in vivo performance of amorphous solid dispersions with pH-sensitive polymers, it is imperative that the in vitro dissolution conditions are carefully considered. Copyright © 2017 Elsevier B.V. All rights reserved.

  18. Integration of biomolecular logic gates with field-effect transducers

    International Nuclear Information System (INIS)

    Poghossian, A.; Malzahn, K.; Abouzar, M.H.; Mehndiratta, P.; Katz, E.; Schoening, M.J.

    2011-01-01

    Highlights: → Enzyme-based AND/OR logic gates are integrated with a capacitive field-effect sensor. → The AND/OR logic gates compose of multi-enzyme system immobilised on sensor surface. → Logic gates were activated by different combinations of chemical inputs (analytes). → The logic output (pH change) produced by the enzymes was read out by the sensor. - Abstract: The integration of biomolecular logic gates with field-effect devices - the basic element of conventional electronic logic gates and computing - is one of the most attractive and promising approaches for the transformation of biomolecular logic principles into macroscopically useable electrical output signals. In this work, capacitive field-effect EIS (electrolyte-insulator-semiconductor) sensors based on a p-Si-SiO 2 -Ta 2 O 5 structure modified with a multi-enzyme membrane have been used for electronic transduction of biochemical signals processed by enzyme-based OR and AND logic gates. The realised OR logic gate composes of two enzymes (glucose oxidase and esterase) and was activated by ethyl butyrate or/and glucose. The AND logic gate composes of three enzymes (invertase, mutarotase and glucose oxidase) and was activated by two chemical input signals: sucrose and dissolved oxygen. The developed integrated enzyme logic gates produce local pH changes at the EIS sensor surface as a result of biochemical reactions activated by different combinations of chemical input signals, while the pH value of the bulk solution remains unchanged. The pH-induced charge changes at the gate-insulator (Ta 2 O 5 ) surface of the EIS transducer result in an electronic signal corresponding to the logic output produced by the immobilised enzymes. The logic output signals have been read out by means of a constant-capacitance method.

  19. Integration of biomolecular logic gates with field-effect transducers

    Energy Technology Data Exchange (ETDEWEB)

    Poghossian, A., E-mail: a.poghossian@fz-juelich.de [Institute of Nano- and Biotechnologies, Aachen University of Applied Sciences, Campus Juelich, Heinrich-Mussmann-Str. 1, D-52428 Juelich (Germany); Institute of Bio- and Nanosystems, Research Centre Juelich GmbH, D-52425 Juelich (Germany); Malzahn, K. [Institute of Nano- and Biotechnologies, Aachen University of Applied Sciences, Campus Juelich, Heinrich-Mussmann-Str. 1, D-52428 Juelich (Germany); Abouzar, M.H. [Institute of Nano- and Biotechnologies, Aachen University of Applied Sciences, Campus Juelich, Heinrich-Mussmann-Str. 1, D-52428 Juelich (Germany); Institute of Bio- and Nanosystems, Research Centre Juelich GmbH, D-52425 Juelich (Germany); Mehndiratta, P. [Institute of Nano- and Biotechnologies, Aachen University of Applied Sciences, Campus Juelich, Heinrich-Mussmann-Str. 1, D-52428 Juelich (Germany); Katz, E. [Department of Chemistry and Biomolecular Science, NanoBio Laboratory (NABLAB), Clarkson University, Potsdam, NY 13699-5810 (United States); Schoening, M.J. [Institute of Nano- and Biotechnologies, Aachen University of Applied Sciences, Campus Juelich, Heinrich-Mussmann-Str. 1, D-52428 Juelich (Germany); Institute of Bio- and Nanosystems, Research Centre Juelich GmbH, D-52425 Juelich (Germany)

    2011-11-01

    Highlights: > Enzyme-based AND/OR logic gates are integrated with a capacitive field-effect sensor. > The AND/OR logic gates compose of multi-enzyme system immobilised on sensor surface. > Logic gates were activated by different combinations of chemical inputs (analytes). > The logic output (pH change) produced by the enzymes was read out by the sensor. - Abstract: The integration of biomolecular logic gates with field-effect devices - the basic element of conventional electronic logic gates and computing - is one of the most attractive and promising approaches for the transformation of biomolecular logic principles into macroscopically useable electrical output signals. In this work, capacitive field-effect EIS (electrolyte-insulator-semiconductor) sensors based on a p-Si-SiO{sub 2}-Ta{sub 2}O{sub 5} structure modified with a multi-enzyme membrane have been used for electronic transduction of biochemical signals processed by enzyme-based OR and AND logic gates. The realised OR logic gate composes of two enzymes (glucose oxidase and esterase) and was activated by ethyl butyrate or/and glucose. The AND logic gate composes of three enzymes (invertase, mutarotase and glucose oxidase) and was activated by two chemical input signals: sucrose and dissolved oxygen. The developed integrated enzyme logic gates produce local pH changes at the EIS sensor surface as a result of biochemical reactions activated by different combinations of chemical input signals, while the pH value of the bulk solution remains unchanged. The pH-induced charge changes at the gate-insulator (Ta{sub 2}O{sub 5}) surface of the EIS transducer result in an electronic signal corresponding to the logic output produced by the immobilised enzymes. The logic output signals have been read out by means of a constant-capacitance method.

  20. Pauli Spin Blockade and the Ultrasmall Magnetic Field Effect

    KAUST Repository

    Danon, Jeroen

    2013-08-06

    Based on the spin-blockade model for organic magnetoresistance, we present an analytic expression for the polaron-bipolaron transition rate, taking into account the effective nuclear fields on the two sites. We reveal the physics behind the qualitatively different magnetoconductance line shapes observed in experiment, as well as the ultrasmall magnetic field effect (USFE). Since our findings agree in detail with recent experiments, they also indirectly provide support for the spin-blockade interpretation of organic magnetoresistance. In addition, we predict the existence of a similar USFE in semiconductor double quantum dots tuned to the spin-blockade regime.

  1. Recent progress in photoactive organic field-effect transistors

    OpenAIRE

    Wakayama, Yutaka; Hayakawa, Ryoma; Seo, Hoon-Seok

    2014-01-01

    Recent progress in photoactive organic field-effect transistors (OFETs) is reviewed. Photoactive OFETs are divided into light-emitting (LE) and light-receiving (LR) OFETs. In the first part, LE-OFETs are reviewed from the viewpoint of the evolution of device structures. Device performances have improved in the last decade with the evolution of device structures from single-layer unipolar to multi-layer ambipolar transistors. In the second part, various kinds of LR-OFETs are featured. These ar...

  2. Directly grown nanocrystalline diamond field-effect transistor microstructures

    Czech Academy of Sciences Publication Activity Database

    Kozak, Halyna; Kromka, Alexander; Babchenko, Oleg; Rezek, Bohuslav

    2010-01-01

    Roč. 8, č. 3 (2010), s. 482-487 ISSN 1546-198X R&D Projects: GA MŠk(CZ) LC06040; GA AV ČR KAN400100701; GA MŠk LC510; GA AV ČR(CZ) IAAX00100902; GA AV ČR KAN400100652 Institutional research plan: CEZ:AV0Z10100521 Keywords : nanocrystalline diamond * microstructures * atomic force microscopy * surface conductivity * field-effect transistor Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.602, year: 2010

  3. Ultrathin regioregular poly(3-hexyl thiophene) field-effect transistors

    DEFF Research Database (Denmark)

    Sandberg, H.G.O.; Frey, G.L.; Shkunov, M.N.

    2002-01-01

    Ultrathin films of regioregular poly(3-hexyl thiophene) (RR-P3HT) were deposited through a dip-coating technique and utilized as the semiconducting film in field-effect transistors (FETs). Proper selection of the substrate and solution concentration enabled the growth of a monolayer-thick RR-P3HT...... film. Atomic force microscopy (AFM), U-V-vis absorption spectroscopy, X-ray reflectivity, and grazing incidence diffraction were used to study the growth mechanism, thickness and orientation of self-organized monolayer thick RR-P3HT films on SiO2 surfaces. Films were found to adopt a Stranski...

  4. Electric field effects on fluorescence of the green fluorescent protein

    Science.gov (United States)

    Nakabayashi, Takakazu; Kinjo, Masataka; Ohta, Nobuhiro

    2008-05-01

    External electric field effects on state energy and photoexcitation dynamics have been examined for a mutant of UV-excited green fluorescent protein (GFPuv5) in a PVA film. The electrofluorescence spectrum of GFPuv5 is reproduced by a linear combination between the fluorescence spectrum and its second derivative spectrum, indicating the field-induced fluorescence quenching and the difference in electric dipole moment between the fluorescent state and the ground state. The direct measurements of the field-induced change in fluorescence decay show that the field-induced quenching results from the field-induced increase in the rate of the non-radiative process from the fluorescent state.

  5. ReS2-based interlayer tunnel field effect transistor

    Science.gov (United States)

    Mohammed, Omar B.; Movva, Hema C. P.; Prasad, Nitin; Valsaraj, Amithraj; Kang, Sangwoo; Corbet, Chris M.; Taniguchi, Takashi; Watanabe, Kenji; Register, Leonard F.; Tutuc, Emanuel; Banerjee, Sanjay K.

    2017-12-01

    In this study, we report the fabrication and characterization of a vertical resonant interlayer tunneling field-effect transistor created using exfoliated, few-layer rhenium disulfide (ReS2) flakes as the electrodes and hexagonal boron nitride as the tunnel barrier. Due to the Γ-point conduction band minimum, the ReS2 based system offers the possibility of resonant interlayer tunneling and associated low-voltage negative differential resistance (NDR) without rotational alignment of the electrode crystal orientations. Substantial NDR is observed, which appears consistent with in-plane crystal momentum conserving tunneling, although considerably broadened by scattering consistent within low mobility ReS2 flakes.

  6. Depth of Field Effects for Interactive Direct Volume Rendering

    KAUST Repository

    Schott, Mathias

    2011-06-01

    In this paper, a method for interactive direct volume rendering is proposed for computing depth of field effects, which previously were shown to aid observers in depth and size perception of synthetically generated images. The presented technique extends those benefits to volume rendering visualizations of 3D scalar fields from CT/MRI scanners or numerical simulations. It is based on incremental filtering and as such does not depend on any precomputation, thus allowing interactive explorations of volumetric data sets via on-the-fly editing of the shading model parameters or (multi-dimensional) transfer functions. © 2011 The Author(s).

  7. Determination of boron in amorphous alloys

    Energy Technology Data Exchange (ETDEWEB)

    Grazhulene, S.S.; Grossman, O.V.; Kuntscher, K.K.; Malygina, L.I.; Muller, E.N.; Telegin, G.F.

    1985-10-01

    In the determination of boron in amorphous alloys containingFe, Co, B, Si, Ni, and P having unusal magnetic and electrical properties, precise analysis and rapid analysis are necessary. To improve the metrological properties of the existing procedure, to find a rapid determination of boron in amorphous alloys, and to verify the accuracy of the results, in the present work the optimization of the photometric determination after extraction of the BF/sup -//sub 4/ ion pair with methylene blue has been studied, and a boron determination by flame photometry using selective methylation has been developed. The determination of boron by the flame photometric and spectrophotometric methods is shown. When a highly precise determination is needed, the spectrophotometric procedure can be used. This procedure is distinguished by its labor intensity and duration. When the need for reproducibility is less severe, the rapid flame photometric procedure is best.

  8. Wear Resistant Amorphous and Nanocomposite Coatings

    Energy Technology Data Exchange (ETDEWEB)

    Racek, O

    2008-03-26

    Glass forming materials (critical cooling rate <10{sup 4}K.s{sup -1}) are promising for their high corrosion and wear resistance. During rapid cooling, the materials form an amorphous structure that transforms to nanocrystalline during a process of devitrification. High hardness (HV 1690) can be achieved through a controlled crystallization. Thermal spray process has been used to apply coatings, which preserves the amorphous/nanocomposite structure due to a high cooling rate of the feedstock particles during the impact on a substrate. Wear properties have been studied with respect to process conditions and feedstock material properties. Application specific properties such as sliding wear resistance have been correlated with laboratory tests based on instrumented indentation and scratch tests.

  9. Annealing behavior of high permeability amorphous alloys

    International Nuclear Information System (INIS)

    Rabenberg, L.

    1980-06-01

    Effects of low temperature annealing on the magnetic properties of the amorphous alloy Co 71 4 Fe 4 6 Si 9 6 B 14 4 were investigated. Annealing this alloy below 400 0 C results in magnetic hardening; annealing above 400 0 C but below the crystallization temperature results in magnetic softening. Above the crystallization temperature the alloy hardens drastically and irreversibly. Conventional and high resolution transmission electron microscopy were used to show that the magnetic property changes at low temperatures occur while the alloy is truly amorphous. By imaging the magnetic microstructures, Lorentz electron microscopy has been able to detect the presence of microscopic inhomogeneities in this alloy. The low temperature annealing behavior of this alloy has been explained in terms of atomic pair ordering in the presence of the internal molecular field. Lorentz electron microscopy has been used to confirm this explanation

  10. Characterization of diamond amorphized by ion implantation

    International Nuclear Information System (INIS)

    Allen, W.R.; Lee, E.H.

    1992-01-01

    Single crystal diamond has been implanted at 1 MeV with 2 x 10 20 Ar/m 2 . Rutherford backscattering spectrometry in a channeled geometry revealed a broad amorphized region underlying a thin, partially crystalline layer. Raman spectroscopy disclosed modifications in the bonding characteristic of the appearance of non-diamond carbon. The complementary nature of the two analysis techniques is demonstrated. The Knoop hardness of the implanted diamond was reduced by implantation

  11. Metastable states in amorphous chalcogenide semiconductors

    CERN Document Server

    Mikla, Victor I

    2009-01-01

    This book addresses an interesting and technologically important class of materials, the amorphous chalcogenide semiconductors. Experimental results on the structural and electronic metastable states in Se-rich chalcogenides are presented. Special attention is paid to the states in the mobility gap and their sensitivity to various factors such as irradiation, annealing and composition. Photoinduced changes of structure and physical properties are also considered and structural transformation at photocrystallization is studied in detail. Finally, the authors discuss potential applications of th

  12. Structural, morphological, compositional and optical studies of plasma polymerized 2-furaldehyde amorphous thin films

    Science.gov (United States)

    Kabir, Humayun; Rahman, M. Mahbubur; Uddin, Kabir M.; Bhuiyan, A. H.

    2017-11-01

    Plasma synthesized 2-furaldehyde (PPFDH) amorphous polymer thin films of varying thicknesses were prepared in optimum conditions by a capacitively coupled parallel plate glow discharge reactor at room temperature. The structure, morphology, composition and optical properties of deposited PPFDH thin films have been investigated using X-Ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, Scanning electron microscopy (SEM), Energy dispersive X-Ray spectroscopy (EDS), as well as Ultraviolet-visible (UV-vis) absorption spectroscopy. XRD results confirmed the amorphous nature of the films. The smooth and uniform nature of the PPFDH thin films were observed by SEM images. FTIR analyses of monomer FDH and PPFDH thin films show that structural rearrangement has occurred due to the synthesis process taking place in the chemical structure. IR stretching bands obtained from DFT calculations of the optimized structures of monomer and polymer of 2-furaldehyde are in good agreement with the experimental results. UV-vis absorption spectra in transmittance as well as reflectance mode was utilized to compute absorption coefficient, allowed direct and indirect transition energy gaps, band edge sharpness, Urbach energy, steepness parameter, extinction coefficient, and dispersion and oscillator energy. The oscillator strength, moments of optical spectra, refractive index at infinite wavelength, high frequency dielectric constant, average oscilator strength, complex refractive index, dissipation factor, optical conductivity and skin depth were also determined by using measured UV-vis transmittance and reflectance spectra.

  13. Fluctuation microscopy analysis of amorphous silicon models

    International Nuclear Information System (INIS)

    Gibson, J.M.; Treacy, M.M.J.

    2017-01-01

    Highlights: • Studied competing computer models for amorphous silicon and simulated fluctuation microscopy data. • Show that only paracrystalline/random network composite can fit published data. • Specifically show that pure random network or random network with void models do not fit available data. • Identify a new means to measure volume fraction of ordered material. • Identify unreported limitations of the Debye model for simulating fluctuation microscopy data. - Abstract: Using computer-generated models we discuss the use of fluctuation electron microscopy (FEM) to identify the structure of amorphous silicon. We show that a combination of variable resolution FEM to measure the correlation length, with correlograph analysis to obtain the structural motif, can pin down structural correlations. We introduce the method of correlograph variance as a promising means of independently measuring the volume fraction of a paracrystalline composite. From comparisons with published data, we affirm that only a composite material of paracrystalline and continuous random network that is substantially paracrystalline could explain the existing experimental data, and point the way to more precise measurements on amorphous semiconductors. The results are of general interest for other classes of disordered materials.

  14. Intrinsic electron trapping in amorphous oxide

    Science.gov (United States)

    Strand, Jack; Kaviani, Moloud; Afanas’ev, Valeri V.; Lisoni, Judit G.; Shluger, Alexander L.

    2018-03-01

    We demonstrate that electron trapping at intrinsic precursor sites is endemic in non-glass-forming amorphous oxide films. The energy distributions of trapped electron states in ultra-pure prototype amorphous (a)-HfO2 insulator obtained from exhaustive photo-depopulation experiments demonstrate electron states in the energy range of 2–3 eV below the oxide conduction band. These energy distributions are compared to the results of density functional calculations of a-HfO2 models of realistic density. The experimental results can be explained by the presence of intrinsic charge trapping sites formed by under-coordinated Hf cations and elongated Hf–O bonds in a-HfO2. These charge trapping states can capture up to two electrons, forming polarons and bi-polarons. The corresponding trapping sites are different from the dangling-bond type defects responsible for trapping in glass-forming oxides, such as SiO2, in that the traps are formed without bonds being broken. Furthermore, introduction of hydrogen causes formation of somewhat energetically deeper electron traps when a proton is immobilized next to the trapped electron bi-polaron. The proposed novel mechanism of intrinsic charge trapping in a-HfO2 represents a new paradigm for charge trapping in a broad class of non-glass-forming amorphous insulators.

  15. Fracture behavior of polymers at low temperatures

    International Nuclear Information System (INIS)

    Saatkamp, T.

    1991-12-01

    The crack propagation behavior of polymers at cryogenic temperatures is determined by the physical processes taking place at the crack tip. It is demonstrated in this paper that stable or unstable crack growth does not depend on the experimental setup, but on the properties of the polymers. The plastification processes at the crack tip are both temperature and time dependent. The critical energy release rate G IC was measured for three polymers, namely semi-crystalline HDPE, amorphous PS and amophous PC, as a function of the crack opening velocity δ at 4.2 and 77 K, respectively. During unstable crack growth, a crack arrest behavior (stick-slip behavior) caused by adiabatic heating and plastification at the crack tip can be observed in most of the polymers. The little specific heat and thermal conductivity of polymers at cryogenic temperatures lead to considerable temperature increases even at small inelastic deformation energies. Under certain conditions, the increase in temperature is sufficient to attain the dispersion range of the second glass transition, as a result of which plastification is intensified. During these processes, the fracture energy R and, hence, the critical energy release rate G IC are increased considerably. (orig.) [de

  16. Increasing the conductivity of crystalline polymer electrolytes

    Science.gov (United States)

    Christie, Alasdair M.; Lilley, Scott J.; Staunton, Edward; Andreev, Yuri G.; Bruce, Peter G.

    2005-01-01

    Polymer electrolytes consist of salts dissolved in polymers (for example, polyethylene oxide, PEO), and represent a unique class of solid coordination compounds. They have potential applications in a diverse range of all-solid-state devices, such as rechargeable lithium batteries, flexible electrochromic displays and smart windows. For 30 years, attention was focused on amorphous polymer electrolytes in the belief that crystalline polymer:salt complexes were insulators. This view has been overturned recently by demonstrating ionic conductivity in the crystalline complexes PEO6:LiXF6 (X = P, As, Sb); however, the conductivities were relatively low. Here we demonstrate an increase of 1.5 orders of magnitude in the conductivity of these materials by replacing a small proportion of the XF6- anions in the crystal structure with isovalent N(SO2CF3)2- ions. We suggest that the larger and more irregularly shaped anions disrupt the potential around the Li+ ions, thus enhancing the ionic conductivity in a manner somewhat analogous to the AgBr1-xIx ionic conductors. The demonstration that doping strategies can enhance the conductivity of crystalline polymer electrolytes represents a significant advance towards the technological exploitation of such materials.

  17. Ferroelectric Polymer Composite with Enhanced Breakdown Strength

    Science.gov (United States)

    Han, Kuo; Gadinski, Matthew; Wang, Qing

    2013-03-01

    Numerous efforts have been made in the past decades to improve the energy storage capability of dielectric capacitors by incorporating ceramic addictives into polymers. Ferroelectric polymers have been particularly interesting as matrix for dielectric composites because of their highest dielectric permittivity and energy density. However, most polymer composites suffer from significantly reduced breakdown strength, which compromises the potential gain in energy density. In this work, various metallic alkoxide were introduced into the functionalized ferroelectric poly(vinylidene fluoride-co- chlorotrifluoroethylene), P(VDF-CTFE), via covalent bonding. The composite with the optimized composition exhibited the Weibull statistical breakdown strength of 504.8 MV/m, 67.6 % higher than the pristine polymer. The enhanced breakdown strength was mainly ascribed to the cross-linking and the formation of deep traps, which effectively reduced the conduction and further lowered the energy loss. Additionally, the homogeneous dispersion of the inorganic phase and the small contrast in permittivity between the polymer and amorphous oxides also contribute to the improved dielectric strength. The dielectric spectra of the composites have been recorded at varied temperatures and frequencies, which revealed the presence of the interfacial polarization layer in the composites.

  18. Characterization of Amorphous and Co-Amorphous Simvastatin Formulations Prepared by Spray Drying

    Directory of Open Access Journals (Sweden)

    Goedele Craye

    2015-12-01

    Full Text Available In this study, spray drying from aqueous solutions, using the surface-active agent sodium lauryl sulfate (SLS as a solubilizer, was explored as a production method for co-amorphous simvastatin–lysine (SVS-LYS at 1:1 molar mixtures, which previously have been observed to form a co-amorphous mixture upon ball milling. In addition, a spray-dried formulation of SVS without LYS was prepared. Energy-dispersive X-ray spectroscopy (EDS revealed that SLS coated the SVS and SVS-LYS particles upon spray drying. X-ray powder diffraction (XRPD and differential scanning calorimetry (DSC showed that in the spray-dried formulations the remaining crystallinity originated from SLS only. The best dissolution properties and a “spring and parachute” effect were found for SVS spray-dried from a 5% SLS solution without LYS. Despite the presence of at least partially crystalline SLS in the mixtures, all the studied formulations were able to significantly extend the stability of amorphous SVS compared to previous co-amorphous formulations of SVS. The best stability (at least 12 months in dry conditions was observed when SLS was spray-dried with SVS (and LYS. In conclusion, spray drying of SVS and LYS from aqueous surfactant solutions was able to produce formulations with improved physical stability for amorphous SVS.

  19. Field-effect enhanced triboelectric colloidal quantum dot flexible sensor

    Science.gov (United States)

    Meng, Lingju; Xu, Qiwei; Fan, Shicheng; Dick, Carson R.; Wang, Xihua

    2017-10-01

    Flexible electronics, which is of great importance as fundamental sensor and communication technologies for many internet-of-things applications, has established a huge market encroaching into the trillion-dollar market of solid state electronics. For the capability of being processed by printing or spraying, colloidal quantum dots (CQDs) play an increasingly important role in flexible electronics. Although the electrical properties of CQD thin-films are expected to be stable on flexible substrates, their electrical performance could be tuned for applications in flexible touch sensors. Here, we report CQD touch sensors employing polydimethylsiloxane (PDMS) triboelectric films. The electrical response of touching activity is enhanced by incorporating CQD field-effect transistors into the device architecture. Thanks to the use of the CQD thin film as a current amplifier, the field-effect CQD touch sensor shows a fast response to various touching materials, even being bent to a large curvature. It also shows a much higher output current density compared to a PDMS triboelectric touch sensor.

  20. Recent Advance in Organic Spintronics and Magnetic Field Effect

    Science.gov (United States)

    Valy Vardeny, Z.

    2013-03-01

    In this talk several important advances in the field of Organic Spintronics and magnetic field effect (MFE) of organic films and optoelectronic devices that have occurred during the past two years from the Utah group will be surveyed and discussed. (i) Organic Spintronics: We demonstrated spin organic light emitting diode (spin-OLED) using two FM injecting electrodes, where the electroluminescence depends on the mutual orientation of the electrode magnetization directions. This development has opened up research studies into organic spin-valves (OSV) in the space-charge limited current regime. (ii) Magnetic field effect: We demonstrated that the photoinduced absorption spectrum in organic films (where current is not involved) show pronounced MFE. This unravels the underlying mechanism of the MFE in organic devices, to be more in agreement with the field of MFE in Biochemistry. (iii) Spin effects in organic optoelectronic devices: We demonstrated that certain spin 1/2 radical additives to donor-acceptor blends substantially enhance the power conversion efficiency of organic photovoltaic (OPV) solar cells. This effect shows that studies of spin response and MFE in OPV devices are promising. In collaboration with T. Nguyen, E. Ehrenfreund, B. Gautam, Y. Zhang and T. Basel. Supported by the DOE grant 04ER46109 ; NSF Grant # DMR-1104495 and MSF-MRSEC program DMR-1121252 [2,3].

  1. Magnetic isotope and magnetic field effects on the DNA synthesis

    Science.gov (United States)

    Buchachenko, Anatoly L.; Orlov, Alexei P.; Kuznetsov, Dmitry A.; Breslavskaya, Natalia N.

    2013-01-01

    Magnetic isotope and magnetic field effects on the rate of DNA synthesis catalysed by polymerases β with isotopic ions 24Mg2+, 25Mg2+ and 26Mg2+ in the catalytic sites were detected. No difference in enzymatic activity was found between polymerases β carrying 24Mg2+ and 26Mg2+ ions with spinless, non-magnetic nuclei 24Mg and 26Mg. However, 25Mg2+ ions with magnetic nucleus 25Mg were shown to suppress enzymatic activity by two to three times with respect to the enzymatic activity of polymerases β with 24Mg2+ and 26Mg2+ ions. Such an isotopic dependence directly indicates that in the DNA synthesis magnetic mass-independent isotope effect functions. Similar effect is exhibited by polymerases β with Zn2+ ions carrying magnetic 67Zn and non-magnetic 64Zn nuclei, respectively. A new, ion–radical mechanism of the DNA synthesis is suggested to explain these effects. Magnetic field dependence of the magnesium-catalysed DNA synthesis is in a perfect agreement with the proposed ion–radical mechanism. It is pointed out that the magnetic isotope and magnetic field effects may be used for medicinal purposes (trans-cranial magnetic treatment of cognitive deceases, cell proliferation, control of the cancer cells, etc). PMID:23851636

  2. Potential of carbon nanotube field effect transistors for analogue circuits

    Directory of Open Access Journals (Sweden)

    Khizar Hayat

    2013-11-01

    Full Text Available This Letter presents a detailed comparison of carbon nanotube field effect transistors (CNFETs and metal oxide semiconductor field effect transistors (MOSFETs with special focus on carbon nanotube FET's potential for implementing analogue circuits in the mm-wave and sub-terahertz range. The latest CNFET lithographic dimensions place it at-par with complementary metal oxide semiconductor in terms of current handling capability, whereas the forecasted improvement in the lithography enables the CNFETs to handle more than twice the current of MOSFETs. The comparison of RF parameters shows superior performance of CNFETs with a g(m, f(T and f(max of 2.7, 2.6 and 4.5 times higher, respectively. MOSFET- and CNFET-based inverter, three-stage ring oscillator and LC oscillator have been designed and compared as well. The CNFET-based inverters are found to be ten times faster, the ring oscillator demonstrates three times higher oscillation frequency and CNFET-based LC oscillator also shows improved performance than its MOSFET counterpart.

  3. Gas Sensors Based on Semiconducting Nanowire Field-Effect Transistors

    Directory of Open Access Journals (Sweden)

    Ping Feng

    2014-09-01

    Full Text Available One-dimensional semiconductor nanostructures are unique sensing materials for the fabrication of gas sensors. In this article, gas sensors based on semiconducting nanowire field-effect transistors (FETs are comprehensively reviewed. Individual nanowires or nanowire network films are usually used as the active detecting channels. In these sensors, a third electrode, which serves as the gate, is used to tune the carrier concentration of the nanowires to realize better sensing performance, including sensitivity, selectivity and response time, etc. The FET parameters can be modulated by the presence of the target gases and their change relate closely to the type and concentration of the gas molecules. In addition, extra controls such as metal decoration, local heating and light irradiation can be combined with the gate electrode to tune the nanowire channel and realize more effective gas sensing. With the help of micro-fabrication techniques, these sensors can be integrated into smart systems. Finally, some challenges for the future investigation and application of nanowire field-effect gas sensors are discussed.

  4. Potential of carbon nanotube field effect transistors for analogue circuits

    KAUST Repository

    Hayat, Khizar

    2013-05-11

    This Letter presents a detailed comparison of carbon nanotube field effect transistors (CNFETs) and metal oxide semiconductor field effect transistors (MOSFETs) with special focus on carbon nanotube FET\\'s potential for implementing analogue circuits in the mm-wave and sub-terahertz range. The latest CNFET lithographic dimensions place it at-par with complementary metal oxide semiconductor in terms of current handling capability, whereas the forecasted improvement in the lithography enables the CNFETs to handle more than twice the current of MOSFETs. The comparison of RF parameters shows superior performance of CNFETs with a g m , f T and f max of 2.7, 2.6 and 4.5 times higher, respectively. MOSFET- and CNFET-based inverter, three-stage ring oscillator and LC oscillator have been designed and compared as well. The CNFET-based inverters are found to be ten times faster, the ring oscillator demonstrates three times higher oscillation frequency and CNFET-based LC oscillator also shows improved performance than its MOSFET counterpart.

  5. Macroscopic local-field effects on photoabsorption processes

    International Nuclear Information System (INIS)

    Ma Xiaoguang; Gong Yubing; Wang Meishan; Wang Dehua

    2008-01-01

    The influence of the local-field effect on the photoabsorption cross sections of the atoms which are embedded in the macroscopic medium has been studied by a set of alternative expressions in detail. Some notes on the validity of some different local-field models used to study the photoabsorption cross sections of atoms in condensed matter have been given for the first time. Our results indicate that the local fields can have substantial and different influence on the photoabsorption cross section of atoms in condensed matter for different models. Clausius-Mossotti model and Onsager model have proved to be more reasonable to describe the local field in gas, liquid, or even some simple solid, while Glauber-Lewenstein model probably is wrong in these conditions except for the ideal gas. A procedure which can avoid the errors introduced by Kramers-Kronig transformation has been implemented in this work. This procedure can guarantee that the theoretical studies on the local field effects will not be influenced by the integral instability of the Kramers-Kronig transformation

  6. Charge carrier velocity in graphene field-effect transistors

    Science.gov (United States)

    Bonmann, Marlene; Vorobiev, Andrei; Andersson, Michael A.; Stake, Jan

    2017-12-01

    To extend the frequency range of transistors into the terahertz domain, new transistor technologies, materials, and device concepts must be continuously developed. The quality of the interface between the involved materials is a highly critical factor. The presence of impurities can degrade device performance and reliability. In this paper, we present a method that allows the study of the charge carrier velocity in a field-effect transistor vs impurity levels. The charge carrier velocity is found using high-frequency scattering parameter measurements followed by delay time analysis. The limiting factors of the saturation velocity and the effect of impurities are then analysed by applying analytical models of the field-dependent and phonon-limited carrier velocity. As an example, this method is applied to a top-gated graphene field-effect transistor (GFET). We find that the extracted saturation velocity is ca. 1.4 ×107 cm/s and is mainly limited by silicon oxide substrate phonons. Within the considered range of residual charge carrier concentrations, charged impurities do not limit the saturation velocity directly by the phonon mechanism. Instead, the impurities act as traps that emit charge carriers at high fields, preventing the current from saturation and thus limiting power gain of the GFETs. The method described in this work helps to better understand the influence of impurities and clarifies methods of further transistor development. High quality interfaces are required to achieve current saturation via velocity saturation in GFETs.

  7. Polymer blends

    Energy Technology Data Exchange (ETDEWEB)

    Allen, Scott D.; Naik, Sanjeev

    2017-08-22

    The present invention provides, among other things, extruded blends of aliphatic polycarbonates and polyolefins. In one aspect, provided blends comprise aliphatic polycarbonates such as poly(propylene carbonate) and a lesser amount of a crystalline or semicrystalline polymer. In certain embodiments, provided blends are characterized in that they exhibit unexpected improvements in their elongation properties. In another aspect, the invention provides methods of making such materials and applications of the materials in applications such as the manufacture of consumer packaging materials.

  8. Moisture-induced phase separation and recrystallization in amorphous solid dispersions.

    Science.gov (United States)

    Luebbert, Christian; Sadowski, Gabriele

    2017-10-30

    Active Pharmaceutical Ingredients (APIs) are often dissolved in polymeric matrices to control the gastrointestinal dissolution and to stabilize the amorphous state of the API. During the pharmaceutical development of new formulations, stability studies via storage at certain temperature and relative humidity (RH) have to be carried out to verify the long-term thermodynamic stability of these formulations against unwanted recrystallization and moisture-induced amorphous-amorphous phase separation (MIAPS). This study focuses on predicting the MIAPS of API/polymer formulations at elevated RH. In a first step, the phase behavior of water-free formulations of ibuprofen (IBU) and felodipine (FEL) combined with the polymers poly(vinyl pyrrolidone) (PVP), poly(vinyl acetate) (PVAC) and poly (vinyl pyrrolidone-co-vinyl acetate) (PVPVA64) was determined experimentally by differential scanning calorimetry (DSC). The phase behavior of these water-free formulations was modeled using the Perturbed-Chain Statistical Associating Fluid Theory (PC-SAFT). Based on this, the API solubility and MIAPS in the above-mentioned formulations at humid conditions was predicted in perfect agreement with the results of two-year lasting stability studies at 25°C/0% RH and 40°C/75% RH. MIAPS was predicted and also experimentally found for the FEL/PVP, FEL/PVPVA64 and IBU/PVP formulations, whereas MIAPS was neither predicted nor measured for the IBU/PVPVA64 system and PVAC-containing formulations. It was thus shown that the results of time-consuming long-term stability tests can be correctly predicted via thermodynamic modeling with PC-SAFT. Copyright © 2017 Elsevier B.V. All rights reserved.

  9. Regioregular narrow-bandgap-conjugated polymers for plastic electronics

    Science.gov (United States)

    Ying, Lei; Huang, Fei; Bazan, Guillermo C.

    2017-03-01

    Progress in the molecular design and processing protocols of semiconducting polymers has opened significant opportunities for the fabrication of low-cost plastic electronic devices. Recent studies indicate that field-effect transistors and organic solar cells fabricated using narrow-bandgap regioregular polymers with translational symmetries in the direction of the backbone vector often outperform those containing analogous regiorandom polymers. This review addresses the cutting edge of regioregularity chemistry, in particular how to control the spatial distribution in the molecular structures and how this order translates to more ordered bulk morphologies. The effect of regioregularity on charge transport and photovoltaic properties is also outlined.

  10. Preparation of degradable porous structures based on 1,3-trimethylene carbonate and D,L-lactide (co)polymers for heart tissue engineering

    NARCIS (Netherlands)

    Pego, AP; Siebum, B; Van Luyn, MJA; Van Seijen, XJGY; Poot, AA; Grijpma, DW; Feijen, J

    2003-01-01

    Biodegradable porous scaffolds for heart tissue engineering were prepared from amorphous elastomeric (co)polymers of 1,3-trimethylene carbonate (TMC) and D,L-lactide (DLLA). Leaching of salt from compression-molded polymer-salt composites allowed the preparation of highly porous structures in a

  11. Solubility of crystalline organic compounds in high and low molecular weight amorphous matrices above and below the glass transition by zero enthalpy extrapolation.

    Science.gov (United States)

    Amharar, Youness; Curtin, Vincent; Gallagher, Kieran H; Healy, Anne Marie

    2014-09-10

    Pharmaceutical applications which require knowledge of the solubility of a crystalline compound in an amorphous matrix are abundant in the literature. Several methods that allow the determination of such data have been reported, but so far have only been applicable to amorphous polymers above the glass transition of the resulting composites. The current work presents, for the first time, a reliable method for the determination of the solubility of crystalline pharmaceutical compounds in high and low molecular weight amorphous matrices at the glass transition and at room temperature (i.e. below the glass transition temperature), respectively. The solubilities of mannitol and indomethacin in polyvinyl pyrrolidone (PVP) K15 and PVP K25, respectively were measured at different temperatures. Mixtures of undissolved crystalline solute and saturated amorphous phase were obtained by annealing at a given temperature. The solubility at this temperature was then obtained by measuring the melting enthalpy of the crystalline phase, plotting it as a function of composition and extrapolating to zero enthalpy. This new method yielded results in accordance with the predictions reported in the literature. The method was also adapted for the measurement of the solubility of crystalline low molecular weight excipients in amorphous active pharmaceutical ingredients (APIs). The solubility of mannitol, glutaric acid and adipic acid in both indomethacin and sulfadimidine was experimentally determined and successfully compared with the difference between their respective calculated Hildebrand solubility parameters. As expected from the calculations, the dicarboxylic acids exhibited a high solubility in both amorphous indomethacin and sulfadimidine, whereas mannitol was almost insoluble in the same amorphous phases at room temperature. This work constitutes the first report of the methodology for determining an experimentally measured solubility for a low molecular weight crystalline solute

  12. Benzodipyrrolidone (BDP)-based polymer semiconductors containing a series of chalcogen atoms: comprehensive investigation of the effect of heteroaromatic blocks on intrinsic semiconducting properties.

    Science.gov (United States)

    Lee, Kyu Cheol; Park, Won-Tae; Noh, Yong-Young; Yang, Changduk

    2014-04-09

    In order to determine the effects of actual 'chalcogen atoms' on semiconducting properties for application in a variety of optoelectronic devices, a class of donor (D)-acceptor (A) polymer semiconductors, namely PBDP-Fu, PBDP-Th, and PBDP-Se, containing the recently formulated benzodipyrrolidone (BDP) accepting unit and furan (Fu), thiophene (Th), or selenophene (Se) as a donating unit has been synthesized, characterized, and used in an active layer of organic field-effect transistors (OFETs). With the LUMO levels being comparatively consistent for all three polymers (-3.58 to -3.60 eV) due to the dominant BDP contribution to the polymer backbone, the HOMO energies are somewhat sensitive to the structurally distinctive feature of the donor counits used. Utilizing a combination of X-ray diffraction (XRD) and atomic force microscopy (AFM), it is apparent that further crystalline domains occur with edge-on orientation for the polymers (PBDP-Th and PBDP-Se) with relatively heavier chalcogen atoms such as Th and Se, compared with PBDP-Fu which has a rather amorphous nature. Investigation of their OFET performance indicates that all the polymers show well balanced ambipolar operations. The desirable morphological structures of both the PBDP-Th and PBDP-Se result in higher mobilities in OFETs than those of PBDP-Fu. In particular, 200 °C annealed PBDP-Se OFETs results in ambipolarity being mobile for both holes of up to 1.7 × 10(-2) cm(2)/V·s and electrodes of up to 1.9 × 10(-2) cm(2)/V·s. In addition, OFETs with PBDP-Th show nearly equivalent charge carrier mobilities for both holes (μ(h) = 1.2 × 10(-2) cm(2)/V·s) and electrons (μ(e) = 1.1 × 10(-2) cm(2)/V·s). Consequently, we systematically demonstrate how the manipulation of existing heteroaromatics can modulate the electronic properties of conjugated D-A polymers, elucidating structure-property relationships that are desirable for the rational design of next generation materials.

  13. The Azobenzene Optical Storage Puzzle - Demands on the Polymer Scaffold?

    DEFF Research Database (Denmark)

    Hvilsted, Søren; Ramanujam, PS

    2001-01-01

    of the nature of the main chain on polyester morphology and on the permanency of the induced anisotropy are discussed. Arguments for the design and methods of preparation of other very different polymer scaffolds supporting the cyanoazobenzene are elucidated. Whereas oligopeptides invariably form amorphous...... materials, both copolymethacrylates and dendritic or hyperbranched polyesters provide some materials that exhibit liquid crystallinity. However, none of these other scaffolds offer materials that allow long-lasting anisotropy to be laser Light induced....

  14. The azobenzene optical storage puzzle - Demands on the polymer scaffold?

    DEFF Research Database (Denmark)

    Hvilsted, Søren; Ramanujam, P.S.

    2001-01-01

    of the nature of the main chain on polyester morphology and on the permanency of the induced anisotropy are discussed. Arguments for the design and methods of preparation of other very different polymer scaffolds supporting the cyanoazobenzene are elucidated. Whereas oligopeptides invariably form amorphous...... materials, both copolymethacrylates and dendritic or hyperbranched polyesters provide some materials that exhibit liquid crystallinity. However, none of these other scaffolds offer materials that allow long-lasting anisotropy to be laser Light induced....

  15. Morphological and charge transport properties of amorphous and crystalline P3HT and PBTTT: insights from theory.

    Science.gov (United States)

    Alberga, Domenico; Perrier, Aurélie; Ciofini, Ilaria; Mangiatordi, Giuseppe Felice; Lattanzi, Gianluca; Adamo, Carlo

    2015-07-28

    We explore the relation between the morphological and the charge transport properties of poly(3-hexylthiophene) (P3HT) and poly(2,5-bis(3-alkylthiophen-2-yl)thieno[3,2-b]thiophene) (PBTTT) semiconductor polymers in both amorphous and crystalline phases. Using molecular dynamics to simulate bulk supercells and the Marcus theory to analyze the transport properties we found that amorphous systems display a reduced hole mobility due to the loss of nematic order and π-π stacking leading to a reduction in the electronic coupling between two chains. In the crystal phase, PBTTT displays a larger charge mobility than P3HT due to the interdigitation of the side chains enhancing the stability of the conjugated rings on the backbones. This more stable π-π stacking reduces the energetic disorder with respect to P3HT and increases the electronic coupling. In contrast, in the amorphous phase, PBTTT displays a reduced charge mobility with respect to P3HT due to the absence of side chains attached to the thienothiophenes, which increases their fluctuations and the energetic disorder. In addition, we show that it is possible to calculate the reorganization energy neglecting the side chains of the polymers and thus saving computational time. Within this approximation, we obtained mobility values matching the experimental measurements, thus confirming that the side chains are crucial to shape the morphology of the polymeric systems but are not involved in the charge transport process.

  16. Spearhead Nanometric Field-Effect Transistor Sensors for Single-Cell Analysis

    Science.gov (United States)

    Córdoba, Ainara López; Ali, Tayyibah; Shevchuk, Andrew; Takahashi, Yasufumi; Novak, Pavel; Edwards, Christopher; Lab, Max; Gopal, Sahana; Chiappini, Ciro; Anand, Uma; Magnani, Luca; Coombes, R. Charles; Gorelik, Julia; Matsue, Tomokazu; Schuhmann, Wolfgang; Klenerman, David; Sviderskaya, Elena V.; Korchev, Yuri

    2016-01-01

    Nanometric field-effect-transistor (FET) sensors are made on the tip of spear-shaped dual carbon nanoelectrodes derived from carbon deposition inside double-barrel nanopipettes. The easy fabrication route allows deposition of semiconductors or conducting polymers to comprise the transistor channel. A channel from electrodeposited poly pyrrole (PPy) exhibits high sensitivity toward pH changes. This property is exploited by immobilizing hexokinase on PPy nano-FETs to give rise to a selective ATP biosensor. Extracellular pH and ATP gradients are key biochemical constituents in the microenvironment of living cells; we monitor their real-time changes in relation to cancer cells and cardiomyocytes. The highly localized detection is possible because of the high aspect ratio and the spear-like design of the nano-FET probes. The accurately positioned nano-FET sensors can detect concentration gradients in three-dimensional space, identify biochemical properties of a single living cell, and after cell membrane penetration perform intracellular measurements. PMID:26816294

  17. Current trends in nanomaterial embedded field effect transistor-based biosensor.

    Science.gov (United States)

    Nehra, Anuj; Pal Singh, Krishna

    2015-12-15

    Recently, as metal-, polymer-, and carbon-based biocompatible nanomaterials have been increasingly incorporated into biosensing applications, with various nanostructures having been used to increase the efficacy and sensitivity of most of the detecting devices, including field effect transistor (FET)-based devices. These nanomaterial-based methods also became the ideal for the amalgamation of biomolecules, especially for the fabrication of ultrasensitive, low-cost, and robust FET-based biosensors; these are categorically very successful at binding the target specified entities in the confined gated micro-region for high functionality. Furthermore, the contemplation of nanomaterial-based FET biosensors to various applications encompasses the desire for detection of many targets with high selectivity, and specificity. We assess how such devices have empowered the achievement of elevated biosensor performance in terms of high sensitivity, selectivity and low detection limits. We review the recent literature here to illustrate the diversity of FET-based biosensors, based on various kinds of nanomaterials in different applications and sum up that graphene or its assisted composite based FET devices are comparatively more efficient and sensitive with highest signal to noise ratio. Lastly, the future prospects and limitations of the field are also discussed. Copyright © 2015 Elsevier B.V. All rights reserved.

  18. Field Effect Transistors Based on Composite Films of Poly(4-vinylphenol) with ZnO Nanoparticles

    Science.gov (United States)

    Boughias, Ouiza; Belkaid, Mohammed Said; Zirmi, Rachid; Trigaud, Thierry; Ratier, Bernard; Ayoub, Nouh

    2018-01-01

    In order to adjust the characteristic of pentacene thin film transistor, we modified the dielectric properties of the gate insulator, poly(4-vinylphenol), or PVP. PVP is an organic polymer with a low dielectric constant, limiting the performance of organic thin film transistors (OTFTs). To increase the dielectric constant of PVP, a controlled amount of ZnO nanoparticles was homogeneously dispersed in a dielectric layer. The effect of the concentration of ZnO on the relative permittivity of PVP was measured using impedance spectroscopy and it has been demonstrated that the permittivity increases from 3.6 to 5.5 with no percolation phenomenon even at a concentration of 50 vol.%. The performance of OTFTs in terms of charge carrier mobility, threshold voltage and linkage current was evaluated. The results indicate a dramatic increase in both the field effect mobility and the linkage current by a factor of 10. It has been demonstrated that the threshold voltage can be adjusted. It shifts from 8 to 0 when the volume concentration of ZnO varied from 0 vol.% to 50 vol.%.

  19. Regulating charge injection in ambipolar organic field-effect transistors by mixed self-assembled monolayers.

    Science.gov (United States)

    Xu, Yong; Baeg, Kang-Jun; Park, Won-Tae; Cho, Ara; Choi, Eun-Young; Noh, Yong-Young

    2014-08-27

    We report on a technique using mixed self-assembled monolayers (SAMs) to finely regulate ambipolar charge injection in polymer organic field-effect transistors. Differing from the other works that employ single SAM specifically for efficient charge injection in p-type and n-type transistors, we blend two different SAMs of alkyl- and perfluoroalkyl thiols at different ratios and apply them to ambipolar OFETs and inverter. Thanks to the utilization of ambipolar semiconductor and one SAM mixture, the device and circuit fabrications are facile with only one step for semiconductor deposition and another for SAM treatment. This is much simpler with respect to the conventional scheme for the unipolar-device-based complementary circuitry that demands separate deposition and processing for individual p-channel and n-channel transistors. Our results show that the mixed-SAM treatments not only improve ambipolar charge injection manifesting as higher hole- and electron-mobility and smaller threshold voltage but also gradually tune the device characteristics to reach a desired condition for circuit application. Therefore, this simple but useful approach is promising for ambipolar electronics.

  20. Polymers for electronics and spintronics.

    Science.gov (United States)

    Bujak, Piotr; Kulszewicz-Bajer, Irena; Zagorska, Malgorzata; Maurel, Vincent; Wielgus, Ireneusz; Pron, Adam

    2013-12-07

    This critical review is devoted to semiconducting and high spin polymers which are of great scientific interest in view of further development of the organic electronics and the emerging organic spintronic fields. Diversified synthetic strategies are discussed in detail leading to high molecular mass compounds showing appropriate redox (ionization potential (IP), electron affinity (EA)), electronic (charge carrier mobility, conductivity), optoelectronic (electroluminescence, photoconductivity) and magnetic (magnetization, ferromagnetic spin interactions) properties and used as active components of devices such as n- and p-channel field effect transistors, ambipolar light emitting transistors, light emitting diodes, photovoltaic cells, photodiodes, magnetic photoswitches, etc. Solution processing procedures developed with the goal of depositing highly ordered and oriented films of these polymers are also described. This is completed by the description of principal methods that are used for characterizing these macromolecular compounds both in solution and in the solid state. These involve various spectroscopic methods (UV-vis-NIR, UPS, pulse EPR), electrochemistry and spectroelectrochemistry, magnetic measurements (SQUID), and structural and morphological investigations (X-ray diffraction, STM, AFM). Finally, four classes of polymers are discussed in detail with special emphasis on the results obtained in the past three years: (i) high IP, (ii) high |EA|, (iii) low band gap and (iv) high spin ones.

  1. Relaxation in polymer electrolytes on the nanosecond timescale

    International Nuclear Information System (INIS)

    Mao, G.; Fernandez-Perea, R.; Price, D.L.; Saboungi, M.-L.; Howells, W.S.

    2000-01-01

    The relation between mechanical and electrical relaxation in polymer/lithium-salt complexes is a fascinating and still unresolved problem in condensed-matter physics, yet has an important bearing on the viability of such materials for use as electrolytes in lithium batteries. At room temperature, these materials are biphasic: they consist of both fluid amorphous regions and salt-enriched crystalline regions. Ionic conduction is known to occur predominantly in the amorphous fluid regions. Although the conduction mechanisms are not yet fully understood, it is widely accepted that lithium ions, coordinated with groups of ether oxygen atoms on single or perhaps double polymer chains, move through re-coordination with other oxygen-bearing groups. The formation and disruption of these coordination bonds must be accompanied by strong relaxation of the local chain structure. Here we probe the relaxation on a nanosecond timescale using quasielastic neutron scattering, and we show that at least two processes are involved: a slow process with a translational character and one or two fast processes with a rotational character. Whereas the former reflects the slowing-down of the translational relaxation commonly observed in polyethylene oxide and other polymer melts, the latter appears to be unique to the polymer electrolytes and has not (to our knowledge) been observed before. A clear picture emerges of the lithium cations forming crosslinks between chain segments and thereby profoundly altering the dynamics of the polymer network.

  2. Dynamics of polymers in the bulk state by neutron scattering

    International Nuclear Information System (INIS)

    Kanaya, Toshiji; Kaji, Keisuke; Kawaguchi, Tatsuya; Inoue, Kazuhiko.

    1992-01-01

    Dynamics of polymers in the bulk state was studied by quasi- and inelastic neutron scattering techniques in the time range of 10 -13 to 10 -10 s. The present work can be classified into three parts: (i) dynamics in the glassy, state, (ii) dynamics near the glass transition and (iii) dynamics in the molten state. In the first section, we discuss the low energy excitation in glassy polymers, which is an origin of anomalous thermal properties of amorphous materials at low temperatures. In the next section, we study dynamics of amorphous polymers near the glass transition which is one of the current topics of solid state physics as well as polymer physics. It was found that two modes of motion appear near the glass transition in the energy ranges near 1 meV and of 10-30μeV. These fast and slow modes arising ca. 50K below T g and just above T g , respectively, are discussed from viewpoints of molecular basis. In the last section, dynamics in the molten state is investigated by focusing on the mechanism of local conformational transition of polymer chains. The results are analyzed in terms of jump diffusion model with damped vibrational motions and compared with the Kramers' rate theory. (author)

  3. Amorphous solid dispersions of piroxicam and Soluplus(®): Qualitative and quantitative analysis of piroxicam recrystallization during storage.

    Science.gov (United States)

    Lust, Andres; Strachan, Clare J; Veski, Peep; Aaltonen, Jaakko; Heinämäki, Jyrki; Yliruusi, Jouko; Kogermann, Karin

    2015-01-01

    The conversion of active pharmaceutical ingredient (API) from amorphous to crystalline form is the primary stability issue in formulating amorphous solid dispersions (SDs). The aim of the present study was to carry out qualitative and quantitative analysis of the physical solid-state stability of the SDs of poorly water-soluble piroxicam (PRX) and polyvinyl caprolactam-polyvinyl acetate-polyethylene-glycol graft copolymer (Soluplus(®)). The SDs were prepared by a solvent evaporation method and stored for six months at 0% RH/6 °C, 0% RH/25 °C, 40% RH/25 °C and 75% RH/25 °C. Fourier transform infrared spectroscopy equipped with attenuated total reflection accessory (ATR-FTIR) and Raman spectroscopy were used for characterizing the physical solid-state changes and drug-polymer interactions. The principal component analysis (PCA) and multivariate curve resolution alternating least squares (MCR-ALS) were used for the qualitative and quantitative analysis of Raman spectra collected during storage. When stored at 0% RH/6 °C and at 0% RH/25 °C, PRX in SDs remained in an amorphous form since no recrystallization was observed by ATR-FTIR and Raman spectroscopy. Raman spectroscopy coupled with PCA and MCR-ALS and ATR-FTIR spectroscopy enabled to detect the recrystallization of amorphous PRX in the samples stored at higher humidity. Copyright © 2015 Elsevier B.V. All rights reserved.

  4. Understanding noise suppression in heterojunction field-effect transistors

    International Nuclear Information System (INIS)

    Green, F.

    1996-01-01

    Full text: The enhanced transport properties displayed by quantum-well-confined, two-dimensional, electron systems underpin the success of heterojunction, field-effect transistors. At cryogenic temperatures, these devices exhibit impressive mobilities and, as a result, high signal gain and low noise. Conventional wisdom has it that the same favourable conditions also hold for normal room-temperature operation. In that case, however, high mobilities are precluded by abundant electron-phonon scattering. Our recent study of nonequilibrium current noise shows that quantum confinement, not high mobility, is the principal source of noise in these devices; this opens up new and exciting opportunities in low-noise transistor design. As trends in millimetre-wave technology push frequencies beyond 100 GHz, it is essential to develop a genuine understanding of noise processes in heterojunction devices

  5. Numerical Modeling of Electromagnetic Field Effects on the Human Body

    Directory of Open Access Journals (Sweden)

    Zuzana Psenakova

    2006-01-01

    Full Text Available Interactions of electromagnetic field (EMF with environment and with tissue of human beings are still under discussion and many research teams are investigating it. The human simulation models are used for biomedical research in a lot of areas, where it is advantage to replace real human body (tissue by the numerical model. Biological effects of EMF are one of the areas, where numerical models are used with many advantages. On the other side, this research is very specific and it is always quite hard to simulate realistic human tissue. This paper deals with different possibilities of numerical modelling of electromagnetic field effects on the human body (especially calculation of the specific absorption rate (SAR distribution in human body and thermal effect.

  6. Electromechanical field effect transistors based on multilayer phosphorene nanoribbons

    Science.gov (United States)

    Jiang, Z. T.; Lv, Z. T.; Zhang, X. D.

    2017-06-01

    Based on the tight-binding Hamiltonian approach, we demonstrate that the electromechanical field effect transistors (FETs) can be realized by using the multilayer phosphorene nanoribbons (PNRs). The synergistic combination of the electric field and the external strains can establish the on-off switching since the electric field can shift or split the energy band, and the mechanical strains can widen or narrow the band widths. This kind of multilayer PNR FETs, much solider than the monolayer PNR one and more easily biased by different electric fields, has more transport channels consequently leading to the higher on-off current ratio or the higher sensitivity to the electric fields. Meanwhile, the strain-induced band-flattening will be beneficial for improving the flexibility in designing the electromechanical FETs. In addition, such electromechanical FETs can act as strain-controlled FETs or mechanical detectors for detecting the strains, indicating their potential applications in nano- and micro-electromechanical fields.

  7. Recent progress in photoactive organic field-effect transistors

    Directory of Open Access Journals (Sweden)

    Yutaka Wakayama

    2014-04-01

    Full Text Available Recent progress in photoactive organic field-effect transistors (OFETs is reviewed. Photoactive OFETs are divided into light-emitting (LE and light-receiving (LR OFETs. In the first part, LE-OFETs are reviewed from the viewpoint of the evolution of device structures. Device performances have improved in the last decade with the evolution of device structures from single-layer unipolar to multi-layer ambipolar transistors. In the second part, various kinds of LR-OFETs are featured. These are categorized according to their functionalities: phototransistors, non-volatile optical memories, and photochromism-based transistors. For both, various device configurations are introduced: thin-film based transistors for practical applications, single-crystalline transistors to investigate fundamental physics, nanowires, multi-layers, and vertical transistors based on new concepts.

  8. Recent progress in photoactive organic field-effect transistors.

    Science.gov (United States)

    Wakayama, Yutaka; Hayakawa, Ryoma; Seo, Hoon-Seok

    2014-04-01

    Recent progress in photoactive organic field-effect transistors (OFETs) is reviewed. Photoactive OFETs are divided into light-emitting (LE) and light-receiving (LR) OFETs. In the first part, LE-OFETs are reviewed from the viewpoint of the evolution of device structures. Device performances have improved in the last decade with the evolution of device structures from single-layer unipolar to multi-layer ambipolar transistors. In the second part, various kinds of LR-OFETs are featured. These are categorized according to their functionalities: phototransistors, non-volatile optical memories, and photochromism-based transistors. For both, various device configurations are introduced: thin-film based transistors for practical applications, single-crystalline transistors to investigate fundamental physics, nanowires, multi-layers, and vertical transistors based on new concepts.

  9. Deep underground disposal of radioactive wastes: Near field effects

    International Nuclear Information System (INIS)

    1985-01-01

    This report reviews the important near-field effects of the disposal of wastes in deep rock formations. The basic characteristics of waste form, container and package, buffer and backfill materials and potential host-rock types are discussed from the perspective of the performance requirements of the total repository system. Effects of waste emplacement on the separate system components and on the system as a whole are discussed. The effects include interactions between groundwater and brines and the other system components, thermal and thermo-mechanical effects, and chemical and geochemical reactions. Special consideration is given to the radiation field that exists in proximity to the waste containers and also to the coupled effects of different phenomena

  10. Two dimensional analytical model for a reconfigurable field effect transistor

    Science.gov (United States)

    Ranjith, R.; Jayachandran, Remya; Suja, K. J.; Komaragiri, Rama S.

    2018-02-01

    This paper presents two-dimensional potential and current models for a reconfigurable field effect transistor (RFET). Two potential models which describe subthreshold and above-threshold channel potentials are developed by solving two-dimensional (2D) Poisson's equation. In the first potential model, 2D Poisson's equation is solved by considering constant/zero charge density in the channel region of the device to get the subthreshold potential characteristics. In the second model, accumulation charge density is considered to get above-threshold potential characteristics of the device. The proposed models are applicable for the device having lightly doped or intrinsic channel. While obtaining the mathematical model, whole body area is divided into two regions: gated region and un-gated region. The analytical models are compared with technology computer-aided design (TCAD) simulation results and are in complete agreement for different lengths of the gated regions as well as at various supply voltage levels.

  11. Recent Trends in Field-Effect Transistors-Based Immunosensors

    Directory of Open Access Journals (Sweden)

    Ana Carolina Mazarin de Moraes

    2016-10-01

    Full Text Available Immunosensors are analytical platforms that detect specific antigen-antibody interactions and play an important role in a wide range of applications in biomedical clinical diagnosis, food safety, and monitoring contaminants in the environment. Field-effect transistors (FET immunosensors have been developed as promising alternatives to conventional immunoassays, which require complicated processes and long-time data acquisition. The electrical signal of FET-based immunosensors is generated as a result of the antigen-antibody conjugation. FET biosensors present real-time and rapid response, require small sample volume, and exhibit higher sensitivity and selectivity. This review brings an overview on the recent literature of FET-based immunosensors, highlighting a diversity of nanomaterials modified with specific receptors as immunosensing platforms for the ultrasensitive detection of various biomolecules.

  12. A tunable colloidal quantum dot photo field-effect transistor

    KAUST Repository

    Ghosh, Subir

    2011-01-01

    We fabricate and investigate field-effect transistors in which a light-absorbing photogate modulates the flow of current along the channel. The photogate consists of colloidal quantum dots that efficiently transfer photoelectrons to the channel across a charge-separating (type-II) heterointerface, producing a primary and sustained secondary flow that is terminated via electron back-recombination across the interface. We explore colloidal quantum dot sizes corresponding to bandgaps ranging from 730 to 1475 nm and also investigate various stoichiometries of aluminum-doped ZnO (AZO) channel materials. We investigate the role of trap state energies in both the colloidal quantum dot energy film and the AZO channel. © 2011 American Institute of Physics.

  13. Reaching saturation in patterned source vertical organic field effect transistors

    Science.gov (United States)

    Greenman, Michael; Sheleg, Gil; Keum, Chang-min; Zucker, Jonathan; Lussem, Bjorn; Tessler, Nir

    2017-05-01

    Like most of the vertical transistors, the Patterned Source Vertical Organic Field Effect Transistor (PS-VOFET) does not exhibit saturation in the output characteristics. The importance of achieving a good saturation is demonstrated in a vertical organic light emitting transistor; however, this is critical for any application requiring the transistor to act as a current source. Thereafter, a 2D simulation tool was used to explain the physical mechanisms that prevent saturation as well as to suggest ways to overcome them. We found that by isolating the source facet from the drain-source electric field, the PS-VOFET architecture exhibits saturation. The process used for fabricating such saturation-enhancing structure is then described. The new device demonstrated close to an ideal saturation with only 1% change in the drain-source current over a 10 V change in the drain-source voltage.

  14. Near-field effects of asteroid impacts in deep water

    Energy Technology Data Exchange (ETDEWEB)

    Gisler, Galen R [Los Alamos National Laboratory; Weaver, Robert P [Los Alamos National Laboratory; Gittings, Michael L [Los Alamos National Laboratory

    2009-06-11

    Our previous work has shown that ocean impacts of asteroids below 500 m in diameter do not produce devastating long-distance tsunamis. Nevertheless, a significant portion of the ocean lies close enough to land that near-field effects may prove to be the greatest danger from asteroid impacts in the ocean. Crown splashes and central jets that rise up many kilometres into the atmosphere can produce, upon their collapse, highly non-linear breaking waves that could devastate shorelines within a hundred kilometres of the impact site. We present illustrative calculations, in two and three dimensions, of such impacts for a range of asteroid sizes and impact angles. We find that, as for land impacts, the greatest dangers from oceanic impacts are the short-term near-field, and long-term atmospheric effects.

  15. Graphene-graphite oxide field-effect transistors.

    Science.gov (United States)

    Standley, Brian; Mendez, Anthony; Schmidgall, Emma; Bockrath, Marc

    2012-03-14

    Graphene's high mobility and two-dimensional nature make it an attractive material for field-effect transistors. Previous efforts in this area have used bulk gate dielectric materials such as SiO(2) or HfO(2). In contrast, we have studied the use of an ultrathin layered material, graphene's insulating analogue, graphite oxide. We have fabricated transistors comprising single or bilayer graphene channels, graphite oxide gate insulators, and metal top-gates. The graphite oxide layers show relatively minimal leakage at room temperature. The breakdown electric field of graphite oxide was found to be comparable to SiO(2), typically ~1-3 × 10(8) V/m, while its dielectric constant is slightly higher, κ ≈ 4.3. © 2012 American Chemical Society

  16. Theoretical study of phosphorene tunneling field effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Jiwon; Hobbs, Chris [SEMATECH, 257 Fuller Rd #2200, Albany, New York 12203 (United States)

    2015-02-23

    In this work, device performances of tunneling field effect transistors (TFETs) based on phosphorene are explored via self-consistent atomistic quantum transport simulations. Phosphorene is an ultra-thin two-dimensional (2-D) material with a direct band gap suitable for TFETs applications. Our simulation shows that phosphorene TFETs exhibit subthreshold slope below 60 mV/dec and a wide range of on-current depending on the transport direction due to highly anisotropic band structures of phosphorene. By benchmarking with monolayer MoTe{sub 2} TFETs, we predict that phosphorene TFETs oriented in the small effective mass direction can yield much larger on-current at the same on-current/off-current ratio than monolayer MoTe{sub 2} TFETs. It is also observed that a gate underlap structure is required for scaling down phosphorene TFETs in the small effective mass direction to suppress the source-to-drain direct tunneling leakage current.

  17. Top- and side-gated epitaxial graphene field effect transistors

    Energy Technology Data Exchange (ETDEWEB)

    Li, Xuebin; Wu, Xiaosong; Sprinkle, Mike; Ming, Fan; Ruan, Ming; Hu, Yike; De Heer, Walt A. [Georgia Institute of Technology, School of Physics, Atlanta, GA (United States); Berger, Claire [Georgia Institute of Technology, School of Physics, Atlanta, GA (United States); CNRS-Institut Neel, Grenoble (France)

    2010-02-15

    Three types of first generation epitaxial graphene (EG) field effect transistors (FET) are presented and their relative merits are discussed. Graphene is epitaxially grown on both the carbon and silicon faces of hexagonal silicon carbide and patterned with electron beam lithography. The channels have a Hall bar geometry to facilitate magnetoresistance measurements. FETs patterned on the Si-face exhibit off-to-on channel resistance ratios that exceed 30. C-face FETs have lower off-to-on resistance ratios, but their mobilities (up to 5000 cm{sup 2}/Vs) are much larger than that for Si-face transistors. Initial investigations into all-graphene side-gate FET structures are promising. Conductivity (left panel) and transport resistances {rho}{sub xx} and {rho}{sub xy} of a top gate graphene Hall bar on SiC Si-face, showing a sign reversal of the hall coefficient at the resistance peak. (Abstract Copyright [2010], Wiley Periodicals, Inc.)

  18. Vertically aligned carbon nanotube field-effect transistors

    KAUST Repository

    Li, Jingqi

    2012-10-01

    Vertically aligned carbon nanotube field-effect transistors (CNTFETs) have been developed using pure semiconducting carbon nanotubes. The source and drain were vertically stacked, separated by a dielectric, and the carbon nanotubes were placed on the sidewall of the stack to bridge the source and drain. Both the effective gate dielectric and gate electrode were normal to the substrate surface. The channel length is determined by the dielectric thickness between source and drain electrodes, making it easier to fabricate sub-micrometer transistors without using time-consuming electron beam lithography. The transistor area is much smaller than the planar CNTFET due to the vertical arrangement of source and drain and the reduced channel area. © 2012 Elsevier Ltd. All rights reserved.

  19. Intrinsic noise in aggressively scaled field-effect transistors

    International Nuclear Information System (INIS)

    Albareda, G; Jiménez, D; Oriols, X

    2009-01-01

    According to roadmap projections, nanoscale field-effect transistors (FETs) with channel lengths below 30 nm and several gates (for improving their gate control over the source–drain conductance) will come to the market in the next few years. However, few studies deal with the noise performance of these aggressively scaled FETs. In this work, a study of the effect of the intrinsic (thermal and shot) noise of such FETs on the performance of an analog amplifier and a digital inverter is carried out by means of numerical simulations with a powerful Monte Carlo (quantum) simulator. The numerical data indicate important drawbacks in the noise performance of aggressively scaled FETs that could invalidate roadmap projections as regards analog and digital applications

  20. Tin - an unlikely ally for silicon field effect transistors?

    KAUST Repository

    Hussain, Aftab M.

    2014-01-13

    We explore the effectiveness of tin (Sn), by alloying it with silicon, to use SiSn as a channel material to extend the performance of silicon based complementary metal oxide semiconductors. Our density functional theory based simulation shows that incorporation of tin reduces the band gap of Si(Sn). We fabricated our device with SiSn channel material using a low cost and scalable thermal diffusion process of tin into silicon. Our high-κ/metal gate based multi-gate-field-effect-transistors using SiSn as channel material show performance enhancement, which is in accordance with the theoretical analysis. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.