WorldWideScience

Sample records for americium ions

  1. Americium-241 and -243 as an ion-engine propellant

    International Nuclear Information System (INIS)

    Schachter, M.M.

    1994-01-01

    Commercially available americium-241 and -243 can be obtained as the mixture of the two isotopes in 100-gram quantities--a product of reprocessing spent nuclear powerplant fuel elements along with plutonium. The half-lives of the isotopes are 450 years for the -241 and 8,000 years for the -243 (the plutonium half-life isotope so obtained is 24,000 years). Americium rolled out in thin foil sheets emits alpha-rays (helium-4 ions) and beta-rays--2 valence electrons for each helium ion. Electrons are also considered as ions. As a foil, the americium radiates only a minimal amount of gamma-rays via the Curie effect. With appropriately designed permanent magnet rings insulated with Wood's alloy, the + and - ions can be accelerated from their already 5.5 million electron-Volts to billion and even trillions of electron-Volts by electronic control grids powered by the magnetohydrodynamic effect of electrons and helium ions streaming at the post-rocket nozzle of the ion engine. Protocol for the estimated thrust of this ion rocket engine is more than ten kilograms continuously sustainable for several thousand years

  2. Preparation of americium metal of high purity and determination of the heat of formation of the hydrated trivalent americium ion

    International Nuclear Information System (INIS)

    Spirlet, J.C.

    1975-10-01

    In order to redetermine some physical and chemical properties of americium metal, several grams of Am-241 have been prepared by two independent methods: lanthanum reduction of the oxide and thermal dissociation of the intermetallic compound Pt 5 Am. After its separation from excess lanthanum or alloy constituent by evaporation, americium metal was further purified by sublimation at 1100 deg C and 10 -6 Torr. Irrespective of the method of preparation, the americium samples displayed the same d.h.c.p. crystal structure. As determined by vacuum hot extraction, the oxygen, nitrogen and hydrogen contents are equal to or smaller than 250, 50 and 20 ppm, respectively. The heats of solution of americium metal (d.c.h.p. structure) in aqueous hydrochloric acid solutions have been measured at 298.15+-0.05K. The standard enthalpy of formation of Am 3+ (aq) is obtained as -616.7+-1.2 kJ mol -1 [fr

  3. Americium recovery from reduction residues

    Science.gov (United States)

    Conner, W.V.; Proctor, S.G.

    1973-12-25

    A process for separation and recovery of americium values from container or bomb'' reduction residues comprising dissolving the residues in a suitable acid, adjusting the hydrogen ion concentration to a desired level by adding a base, precipitating the americium as americium oxalate by adding oxalic acid, digesting the solution, separating the precipitate, and thereafter calcining the americium oxalate precipitate to form americium oxide. (Official Gazette)

  4. Structural characterisations and mechanistic investigations of the selective dissolution of americium by the ferricyanide ions in alkaline media. Application for the partitioning americium curium

    International Nuclear Information System (INIS)

    Fouchard, Sebastien

    2000-01-01

    Americium exhibits a high solubility form in basic media under oxidant conditions, unlike the other Transplutonium elements (TPE). This property can be used in the frame of High Level Liquid Waste (HLLW) treatment in order to extract preferentially the americium element, the main responsible of the long term radiotoxicity of the nuclear waste. This soluble compound can be obtained by addition of a concentrated basic solution of Fe(CN) 6 3- ions on Am(OH) 3 precipitates. This technique enables a rapid extraction of Am by the synthesis of this soluble form in alkaline solutions. Under these conditions, the other TPE remain in the solid state as trivalent hydroxide solids, strongly insoluble. In the case of dissolutions involving large amounts of Am(OH) 3 , the formation of the soluble complex is concomitant with the appearance of a reddish precipitate in the basic solution. Dissolution experiments which were carried out on this solid in NaOH/Fe(CN) 6 3- have demonstrated the dependency of the solubility equilibria with the media. Spectroscopic studies (UV Visible, XAS) on the precipitate have enabled the determination of the chemical structure and the oxidation state of the americium in the solid: Na 2 Am(V)O 2 (OH) 3 ,nH 2 O. Electrochemical studies on the americium solution have confirmed that the oxidation of Am(OH) 3 by the Fe(CN) 6 3- ions in basic media could only lead to the pentavalent form. A stoichiometric study carries out between a AmO 2 + ion and one Fe(CN) 6 3- ion and the spectroscopic characterisation of this reaction have demonstrated that the Fe(CN) 6 3- ion didn't remain as an un-complexed form in solution after the alkaline mixing. These results tend to prove that this dissolution of Am(OH) 3 is much more complex than a simple oxidation by the Fe(CN) 6 3- ions. The existence of molecular interactions between AmO 2 + and Fe(CN) 6 3- has been postulated and a mechanistic scheme has been proposed in order to explain the appearance of the soluble

  5. On the americium oxalate solubility

    International Nuclear Information System (INIS)

    Zakolupin, S.A.; Korablin, Eh.V.

    1977-01-01

    The americium oxalate solubility at different nitric (0.0-1 M) and oxalic (0.0-0.4 M) acid concentrations was investigated in the temperature range from 14 to 60 deg C. The dependence of americium oxalate solubility on the oxalic acid concentration was determined. Increasing oxalic acid concentration was found to reduce the americium oxalate solubility. The dependence of americium oxalate solubility on the oxalic acid concentration was noted to be a minimum at low acidity (0.1-0.3 M nitric acid). This is most likely due to Am(C 2 O 4 ) + , Am(C 2 O 4 ) 2 - and Am(C 2 O 4 ) 3 3- complex ion formation which have different unstability constants. On the basis of the data obtained, a preliminary estimate was carried out for the product of americium oxalate solubility in nitric acid medium (10 -29 -10 -31 ) and of the one in water (6.4x10 -20 )

  6. Determination of americium and curium using ion-exchange in the nitric-acid-methanol medium for environmental analysis

    International Nuclear Information System (INIS)

    Holm, E.; Fukai, R.

    1976-01-01

    While transplutonic elements are only slightly sorbed to anion exchangers from hydrochloric or nitric acid media, the presence of alcohol enhances the anionic exchange of these elements, especially in nitric and sulfuric solutions. In the present work a method has been developed for determining americium and curium in environmental samples, on the basis of the difference between the sorption characteristics to anion exchangers in the acid-methanol system of these transplutonic elements and those of plutonium, polonium and thorium. The method also permits us to perform sequential determination of plutonium, when necessary

  7. Americium removal from nitric acid waste streams

    International Nuclear Information System (INIS)

    Muscatello, A.C.; Navratil, J.D.

    1986-01-01

    Separations research at the Rocky Flats Plant (RFP) has found ways to significantly improve americium removal from nitric acid (7M) waste streams generated by plutonium purification operations. Partial neutralization of the acid waste followed by solid supported liquid membranes (SLM) are useful in transferring and concentrating americium from nitrate solutions. Specifically, DHDECMP (dihexyl-N,N-diethylcarbamoylmethylphosphonate) supported on Accurel polypropylene hollow fibers assembled in modular form transfers >95% of the americium from high nitrate (6.9M), low acid (0.1M) feeds into 0.25M oxalic acid stripping solution. Maximum permeabilities were observed to be 0.001 cm/sec, consistent with typical values for other systems. The feed:strip volume ratio shows an inverse relationship to the fraction of metal ion transferred. Cation exchangers may be used to concentrate americium from the strip solution. Furthermore, O0D (iB)CMPO (or CMPO) (octylphenyl-N-N-diisobutylcarbamoylmethylphosphine oxide) has been tested in an extraction chromatography mode. Preliminary results show CMPO to be effective in removing americium if the feed is neutralized to 1.0M acidity and iron(III) is complexed with 0.20M oxalic acid. 3 figs

  8. Biosorption of americium by alginate beads

    International Nuclear Information System (INIS)

    Borba, Tania Regina de; Marumo, Julio Takehiro; Goes, Marcos Maciel de; Ferreira, Rafael Vicente de Padua; Sakata, Solange Kazumi

    2009-01-01

    The use of biotechnology to remove heavy metals from wastes plays great potential in treatment of radioactive wastes and therefore the aim of this study was to evaluate the biosorption of americium by alginate beads. Biosorption has been defined as the property of certain biomolecules to bind and remove selected ions or other molecules from aqueous solutions. The calcium alginate beads as biosorbent were prepared and analyzed for americium uptaking. The experiments were performed in different solution activity concentrations, pH and exposure time. The results suggest that biosorption process is more efficient at pH 4 and for 75, 150, 300 Bq/mL and 120 minutes were necessary to remove almost 100% of the americium-241 from the solution. (author)

  9. Accidental exposure to americium

    International Nuclear Information System (INIS)

    Heid, K.R.

    1985-04-01

    This report desribes an accident in which a 64-year old Hanford nuclear worker was exposed to high levels of americium while working in an americium recovery facility in 1976. As a result of the accident, he was heavily externally contaminated with americium, sustained with a substantial internal deposition of this isotope, and was burned with concentrated nitric acid and injured by flying debris about the face and neck. The immediate and longer-term treatment given the patient, including the decontamination efforts and clinical laboratory studies, are discussed. Special in-vivo equipment and techniques were used to measure the americium deposited in the patient. These and subsequent in-vivo measurements were used to estimate the dose rates and the accumulated doses to body organs. Urinary and fecal excreta were collected and analyzed for americium content. The interpretation of these data was complicated by the fact that the intake resulted both from inhalation and from solubilization of the americium embedded in facial tissues as a result of the accident. A total of 1100 μCi was excreted in urine and feces during the first 2 years following the accident. The long-term use of diethylenetriaminepentaacetic acid (DTPA), used principally as the zinc salt, is discussed including the method, route of administration, and effectiveness. To date, the patient has apparently experienced no complications attributable to this extensive course of therapy, even though he was given approximately 560 g of DTPA. 6 refs

  10. Determination of americium in urine

    International Nuclear Information System (INIS)

    Shvydko, N.S.; Mikhajlova, O.A.; Popov, D.K.

    1988-01-01

    A technique has been developed for the determination of americium 241 in urine by a raiochemical purification of the nuclide from uranium (upon co-precipitation of americium 241 with calcium and lanthanum), plutonium, thorum, and polonium 210 (upon co-precipitation of these radionuclides with zirconium iodate). α-Radioactivity was measured either in a thick layer of the americium 241 precipitate with a nonisotope carrier or in thin-layer preparations after electrolytic precipitation of americium 241 on a cathode

  11. Selective extraction of americium(III) over europium(III) ions with pyridylpyrazole ligands. Structure-property relationships

    Energy Technology Data Exchange (ETDEWEB)

    Su, Dongping; Liu, Ying; Li, Shimeng; Ding, Songdong; Jin, Yongdong; Wang, Zhipeng; Hu, Xiaoyang; Zhang, Lirong [Department of chemistry, Sichuan University, Chengdu (China)

    2017-01-18

    To clarify the structure-property relationships of pyridylpyrazole ligands and provide guidance for the design of new and more efficient ligands for the selective extraction of actinides over lanthanides, a series of alkyl-substituted pyridylpyrazole ligands with different branched chains at different positions of the pyrazole ring were synthesized. Extraction experiments showed that the pyridylpyrazole ligands exhibited good selective extraction abilities for Am{sup III} ions, and the steric effects of the branched chain had a significant impact on the distribution ratios of Am{sup III} and Eu{sup III} ions as well as the separation factor. Moreover, both slope analyses and UV/Vis spectrometry titrations indicated the formation of a 1:1 complex of 2-(1-octyl-1H-pyrazol-3-yl)pyridine (C8-PypzH) with Eu{sup III} ions. The stability constant (log K) for this complex obtained from the UV/Vis titration was 4.45 ± 0.04. Single crystals of the complexes of 3-(2-pyridyl)pyrazole (PypzH) with Eu(NO{sub 3}){sub 3} and Sm(NO{sub 3}){sub 3} were obtained; PypzH acts as a bidentate ligand in the crystal structures, and the N atom with a bound H atom did not participate in the coordination. In general, this study revealed some interesting findings on the effects of the alkyl-chain structure and the special complexation between pyridylpyrazole ligands and Ln{sup III} ions. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  12. Chemistry of americium

    Energy Technology Data Exchange (ETDEWEB)

    Schulz, W.W.

    1976-01-01

    Essential features of the descriptive chemistry of americium are reviewed. Chapter titles are: discovery, atomic and nuclear properties, collateral reading, production and uses, chemistry in aqueous solution, metal, alloys, and compounds, and, recovery, separation, purification. Author and subject indexes are included. (JCB)

  13. 1976 Hanford americium accident

    International Nuclear Information System (INIS)

    Heid, K.R.; Breitenstein, B.D.; Palmer, H.E.; McMurray, B.J.; Wald, N.

    1979-01-01

    This report presents the 2.5-year medical course of a 64-year-old Hanford nuclear chemical operator who was involved in an accident in an americium recovery facility in August 1976. He was heavily externally contaminated with americium, sustained a substantial internal deposition of this isotope, and was burned with concentrated nitric acid and injured by flying debris about the face and neck. The medical care given the patient, including the decontamination efforts and clinical laboratory studies, are discussed. In-vivo measurements were used to estimate the dose rates and the accumulated doses to body organs. Urinary and fecal excreta were collected and analyzed for americium content. Interpretation of these data was complicated by the fact that the intake resulted both from inhalation and from solubilization of the americium embedded in facial tissues. A total of 1100 μCi was excreted in urine and feces during the first 2 years following the accident. The long-term use of diethylenetriaminepentate (DTPA), used principally as the zinc salt, is discussed including the method, route of administration, and effectiveness. To date, the patient has apparently experienced no complications attributable to this extensive course of therapy, even though he has been given approximately 560 grams of DTPA. 4 figures, 1 table

  14. Americium separations from high salt solutions

    International Nuclear Information System (INIS)

    Barr, Mary E.; Jarvinen, Gordon D.; Schulte, Louis D.; Stark, Peter C.; Chamberlin, Rebecca M.; Abney, Kent D.; Ricketts, Thomas E.; Valdez, Yvette E.; Bartsch, Richard A.

    2000-01-01

    Americium (III) exhibits an unexpectedly high affinity for anion-exchange material from the high-salt evaporator bottoms solutions--an effect which has not been duplicated using simple salt solutions. Similar behavior is observed for its lanthanide homologue, Nd(III), in complex evaporator bottoms surrogate solutions. There appears to be no single controlling factor--acid concentration, total nitrate concentration or solution ionic strength--which accounts for the approximately 2-fold increase in retention of the trivalent ions from complex solutions relative to simple solutions. Calculation of species activities (i.e., water, proton and nitrate) in such concentrated mixed salt solutions is difficult and of questionable accuracy, but it is likely that the answer to forcing formation of anionic nitrate complexes of americium lies in the relative activities of water and nitrate. From a practical viewpoint, the modest americium removal needs (ca. 50--75%) from nitric acid evaporator bottoms allow sufficient latitude for the use of non-optimized conditions such as running existing columns filled with older, well-used Reillex HPQ. Newer materials, such as HPQ-100 and the experimental bifunctional resins, which exhibit higher distribution coefficients, would allow for either increased Am removal or the use of smaller columns. It is also of interest that one of the experimental neutral-donor solid-support extractants, DHDECMP, exhibits a similarly high level of americium (total alpha) removal from EV bottoms and is much less sensitive to total acid content than commercially-available material

  15. Chromatographic studies of the lanthanide element separation for the americium/curium large scale separation using ion exchange resins

    International Nuclear Information System (INIS)

    Ginisty, Claude.

    1981-06-01

    The Am/Cm large scale separations, operated by chromatography with the use of ion exchange resins, are described by numerous publications. The bibliographic studies allow to retain the followed points: use of sulfonate cationic resins, development by elution with the α-hydroxyisobutyric acid, column loadings between 1 and 30% of the capacity, possibility to use no radioactive lanthanides prior to actinides for trial purposes. The optimisation of such a process is the major part of this thesis. This point is realised by introducing a new definition for the resolution, for non symmetrical elution peaks, and a measure of this dissymmetry by introducing a shape factor F. For the separation itself and for the pressure drop in the column, the influence of the following parameters are studied: composition of the elution solution (concentration and pH), column temperature (20 to 90 0 C), resin size (9 to 27 μm), rate flow of mobile phase (70 ml.cm -2 .mn -1 ), column length and diameter. Symmetrical elution peaks may be obtained, even with a 27% loading. Elution conditions may be modified during the separation process in order to have the best recovery for the two components (1,3 [fr

  16. Recycling of americium

    International Nuclear Information System (INIS)

    Hagstroem, Ingela

    1999-12-01

    Separation of actinides from spent nuclear fuel is a part of the process of recycling fissile material. Extracting agents for partitioning the high level liquid waste (HLLW) from conventional PUREX reprocessing is studied. The CTH-process is based on three consecutive extraction cycles. In the first cycle protactinium, uranium, neptunium and plutonium are removed by extraction with di-2-ethylhexyl-phosphoric acid (HDEHP) from a 6 M nitric acid HLLW solution. Distribution ratios for actinides, fission products and corrosion products between HLLW and 1 M HDEHP in an aliphatic diluent have been investigated. To avoid addition of chemicals the acidity is reduced by a tributylphosphate (TBP) extraction cycle. The distribution ratios of elements present in HLLW have been measured between 50 % TBP in an aliphatic diluent and synthetic HLLW in range 0.1-6 M nitric acid. In the third extraction cycle americium and curium are extracted. To separate trivalent actinides from lanthanides a method based on selective stripping of the actinides from 1 M HDEHP is proposed. The aqueous phase containing ammonia, diethylenetriaminepentaacetic acid (DTPA) and lactic acid is recycled in a closed loop after reextraction of the actinides into a second organic phase also containing 1 M HDEHP. Distribution ratios for americium and neodymium have been measured at varying DTPA and lactic acid concentrations and at varying pH. Nitrogen-donor reagents have been shown to have a potential to separate trivalent actinides from lanthanides. 2,2':6,2''-terpyridine as extractant follows the CHON-principle and can in synergy with 2-bromodecanoic acid separate americium from europium. Distribution ratios for americium and europium, in the range of 0.02-0.12 M nitric acid, between nitric acid and 0.02 M terpyridine with 1 M 2-bromodecanoic acid in tert-butylbenzene (TBB) was investigated. Comparison with other nitrogen-donor reagents show that increasing lipophilicity of the molecule, by substitution of

  17. Supported extractant membranes for americium and plutonium recovery

    International Nuclear Information System (INIS)

    Muscatello, A.C.; Navratil, J.D.; Killion, M.E.; Price, M.Y.

    1987-01-01

    Solid supported liquid membranes(SLM) are useful in transferring and concentrating americium and plutonium from nitrate solutions. Specifically, DHDECMP(dihexyl-N,N-diethylcarbamoylmethylphosphonate) supported on Accurel or Celgard polypropylene hollow fibers assembled in modular form transfers >95% of the americium and >70% of the plutonium from high nitrate (6.9 M), low acid (0.1 M) feeds into 0.25 M oxalic acid stripping solution. Membranes supporting TBP (tri-n-butylphosphate) also transfer these metal ions. Maximum permeabilities were observed to be 1 x 10 -3 cm sec -1 , similar to the values for other systems. The feed:strip volume ratio shows an inverse relationship to the fraction of metal ion transferred. Cation exchangers may be used to concentrate americium from the strip solution

  18. Americium-241 - ED 4308

    International Nuclear Information System (INIS)

    Ammerich, M.; Frot, P.; Gambini, D.; Gauron, C.; Moureaux, P.; Herbelet, G.; Lahaye, T.; Le Guen, B.; Pihet, P.; Rannou, A.; Vidal, E.

    2012-12-01

    This sheet presents the characteristics of Americium-241, its origin, and its radio-physical and biological properties. It briefly describes its use in nuclear medicine. It indicates its dosimetric parameters for external exposure, cutaneous contamination, and internal exposure due to acute contamination or to chronic contamination. It indicates and comments the various exposure control techniques: ambient dose rate measurement, surface contamination measurement, atmosphere contamination. It addresses the means of protection: premise design, protection against external exposure and against internal exposure. It describes how areas are delimited and controlled within the premises: regulatory areas, controls to be performed. It addresses the personnel classification, training and medical survey. It addresses the issue of wastes and effluents. It briefly recalls the administrative procedures related to the authorization and declaration of possession and use of sealed and unsealed sources. It indicates regulatory aspects related to the road transport of Americium-241, describes what is to be done in case of incident or accident (for the different types of contamination or exposure)

  19. Determination of plutonium, americium and curium in the marine environment

    International Nuclear Information System (INIS)

    Grenaut, CLaude; Germain, Pierre; Miramand, Pierre.

    1982-01-01

    The method used in the Laboratory for plutonium, americium and curium determination in marine samples (water, sediments, animals, plants) is presented. It is a modification of a procedure based on adsorption on ion exchange resins developed by other authors. The preliminary preparation of the samples, the radiochemical procedures and electrodeposition are described so as to be used as a practical handbook [fr

  20. Americium product solidification and disposal

    International Nuclear Information System (INIS)

    Mailen, J.C.; Campbell, D.O.; Bell, J.T.; Collins, E.D.

    1987-01-01

    The americium product from the TRUEX processing plant needs to be converted into a form suitable for ultimate disposal. An evaluation of the disposal based on safety, number of process steps, demonstrated operability of the processes, production of low-level alpha waste streams, and simplicity of maintenance with low radiation exposures to personnel during maintenance, has been made. The best process is to load the americium on a cation exchange resin followed by calcination or oxidation of the resin after loading

  1. Americium in the Finnish environment

    Energy Technology Data Exchange (ETDEWEB)

    Lehto, J. (Helsinki Univ., Lab. of Radiochemistry (Finland))

    2009-07-01

    This paper reviews studies on environmental americium,241 Am, in Finland. There are two sources of americium in the Finnish environment: fallouts from nuclear weapons tests in the 1950s and 1960s and from the Chernobyl accident in 1986, the former constituting around 98% of the total environmental load. The weapons test fallout was distributed more or less uniformly over Finland, while the Chernobyl fallout was deposited on a sector from southwestern coast to northeast. The total deposition of 241 Am in Finland is approximately 20 Bq m-2 and the amount is still somewhat increasing due to decay of 241 Pu. In this paper, the distribution and migration of americium in forest and aquatic environments is described. Americium concentrations in natural waters, sediments, soils, vegetation and fishes are given. In addition, the behaviour of americium in the food chain from lichen via reindeer into man is discussed. Radiation doses to humans due to the environmental americium in Finland are of no practical importance (orig.)

  2. Contribution to the study of higher valency states of americium

    International Nuclear Information System (INIS)

    Langlet, Jean.

    1976-01-01

    Study of the chemistry of the higher valencies of americium in aqueous solutions and especially the autoreduction phenomenon. First a purification method of americium solutions is studied by precipitation, solvent extraction and ion exchange chromatography. Studies of higher valency states chemical properties are disturbed by the autoreduction phenomenon changing Am VI and Am V in Am III more stable. Stabilization of higher valency states, characterized by a steady concentration of Am VI in solution, can be done by complexation of Am VI and Am V ions or by a protecting effect of foreign ions. The original medium used has a complexing effect by SO 4 2- ions and a protecting effect by the system S 2 O 8 2- -Ag + consuming H 2 O 2 main reducing agent produced by water radiolysis. These effects are shown by the study of Am VI in acid and basic solutions. A mechanism of the stabilization effect is given [fr

  3. Plutonium and americium separation from salts

    International Nuclear Information System (INIS)

    Hagan, P.G.; Miner, F.J.

    1976-01-01

    Salts or materials containing plutonium and americium are dissolved in hydrochloric acid, heated, and contacted with an alkali metal carbonate solution to precipitate plutonium and americium carbonates which are thereafter readily separable from the solution

  4. Selective leaching studies of deep-sea sediments loaded with americium, neptunium and plutonium

    International Nuclear Information System (INIS)

    Cole, T.G.; Higgo, J.J.W.; Cronan, D.S.; Rees, L.V.C.

    1984-07-01

    A series of selective leaching experiments were undertaken to investigate the solid phase speciation and distribution of americium, neptunium and plutonium which had been experimentally loaded onto different marine sediment types. The chemical leaches employed showed rather poor selectivity but certain trends were evident. Adsorption was not by ion exchange. Americium showed a preferential affinity for carbonate and plutonium for organic matter. Neptunium appeared to have no preferential affinities. Americium was sorbed by acetic acid residues (CaCO 3 removed) and by unleached carbonate-rich sediments with equal efficiency. This indicates that it is able to diversify its solid phase affinity/distribution depending upon which solid phases are available. (author)

  5. Reduction Rates for Higher Americium Oxidation States in Nitric Acid

    Energy Technology Data Exchange (ETDEWEB)

    Grimes, Travis Shane [Idaho National Lab. (INL), Idaho Falls, ID (United States); Mincher, Bruce Jay [Idaho National Lab. (INL), Idaho Falls, ID (United States); Schmitt, Nicholas C [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-09-30

    The stability of hexavalent americium was measured using multiple americium concentrations and nitric acid concentrations after contact with the strong oxidant sodium bismuthate. Contrary to our hypotheses Am(VI) was not reduced faster at higher americium concentrations, and the reduction was only zero-order at short time scales. Attempts to model the reduction kinetics using zero order kinetic models showed Am(VI) reduction in nitric acid is more complex than the autoreduction processes reported by others in perchloric acid. The classical zero-order reduction of Am(VI) was found here only for short times on the order of a few hours. We did show that the rate of Am(V) production was less than the rate of Am(VI) reduction, indicating that some Am(VI) undergoes two electron-reduction to Am(IV). We also monitored the Am(VI) reduction in contact with the organic diluent dodecane. A direct comparison of these results with those in the absence of the organic diluent showed the reduction rates for Am(VI) were not statistically different for both systems. Additional americium oxidations conducted in the presence of Ce(IV)/Ce(III) ions showed that Am(VI) is reduced without the typical growth of Am(V) observed in the systems sans Ce ion. This was an interesting result which suggests a potential new reduction/oxidation pathway for Am in the presence of Ce; however, these results were very preliminary, and will require additional experiments to understand the mechanism by which this occurs. Overall, these studies have shown that hexavalent americium is fundamentally stable enough in nitric acid to run a separations process. However, the complicated nature of the reduction pathways based on the system components is far from being rigorously understood.

  6. Recovery of americium-241 from aged plutonium metal

    International Nuclear Information System (INIS)

    Gray, L.W.; Burney, G.A.; Reilly, T.A.; Wilson, T.W.; McKibben, J.M.

    1980-12-01

    About 5 kg of ingrown 241 Am was recovered from 850 kg of aged plutonium using a process developed specifically for Savannah River Plant application. The aged plutonium metal was first dissolved in sulfamic acid. Sodium nitrite was added to oxidize the plutonium to Pu(IV) and the residual sulfamate ion was oxidized to nitrogen gas and sulfate. The plutonium and americium were separated by one cycle of solvent extraction. The recovered products were subsequently purified by cation exchange chromatography, precipitated as oxalates, and calcined to the oxides. Plutonium processng was routine. Before cation exchange purification, the aqueous americium solution from solvent extraction was concentrated and stripped of nitric acid. More than 98% of the 241 Am was then recovered from the cation exchange column where it was effectively decontaminated from all major impurities except nickel and chromium. This partially purified product solution was concentrated further by evaporation and then denitrated by reaction with formic acid. Individual batches of americium oxalate were then precipitated, filtered, washed, and calcined. About 98.5% of the americium was recovered. The final product purity averaged 98% 241 AmO 2 ; residual impurities were primarily lead and nickel

  7. Higher Americium Oxidation State Research Roadmap

    Energy Technology Data Exchange (ETDEWEB)

    Mincher, Bruce J. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Law, Jack D. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Goff, George S. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Moyer, Bruce A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Burns, Jon D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Lumetta, Gregg J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Sinkov, Sergey I. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Shehee, Thomas C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hobbs, David T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-12-18

    The partitioning of hexavalent Am from dissolved nuclear fuel requires the ability to efficiently oxidize Am(III) to Am(VI) and to maintain that oxidation state for a length of time sufficient to perform the separation. Several oxidants have been, or are being developed. Chemical oxidants include Ag-catalyzed ozone, Ag-catalyzed peroxydisulfate, Cu(III) periodate, and sodium bismuthate. Hexavalent americium has also now successfully been prepared by electrolysis, using functionalized electrodes. So-called auto-reduction rates of Am(VI) are sufficiently slow to allow for separations. However, for separations based on solvent extraction or ion exchange using organic resins, the high valence state must be maintained under the reducing conditions of the organic phase contact, and a holding oxidant is probably necessary. Until now, only Cu(III) periodate and sodium bismuthate oxidation have been successfully combined with solvent extraction separations. Bismuthate oxidation provided the higher DAm, since it acts as its own holding oxidant, and a successful hot test using centrifugal contactors was performed. For the other oxidants, Ag-catalyzed peroxydisulfate will not oxidize americium in nitric acid concentrations above 0.3 M, and it is not being further investigated. Peroxydisulfate in the absence of Ag catalysis is being used to prepare Am(V) in ion exchange work, discussed below. Preliminary work with Ag-catalyzed ozone has been unsuccessful for extractions of Am(VI) from 6.5 M HNO3, and only one attempt at extraction, also from 6.5 M HNO3, using the electrolytic oxidation has been attempted. However, this high acid concentration was based on the highest Am extraction efficiency using the bismuthate oxidant; which is only sparingly soluble, and thus the oxidation yield is based on bismuthate solubility. Lower acid concentrations may be sufficient with alternative oxidants and work with Ag-ozone, Cu(III) and electrolysis is on-going. Two non

  8. Isolation of high purity americium metal via distillation

    Science.gov (United States)

    Squires, Leah N.; King, James A.; Fielding, Randall S.; Lessing, Paul

    2018-03-01

    Pure americium metal is a crucial component for the fabrication of transmutation fuels. Unfortunately, americium in pure metal form is not available; however, a number of mixed metals and mixed oxides that include americium are available. In this manuscript a method is described to obtain high purity americium metal from a mixture of americium and neptunium metals with lead impurity via distillation.

  9. Transmutation of Americium in Fast Neutron Facilities

    OpenAIRE

    Zhang, Youpeng

    2011-01-01

    In this thesis, the feasibility to use a medium sized sodium cooled fast reactor fully loaded with MOX fuel for efficient transmutation of americium is investigated by simulating the safety performance of a BN600-type fast reactor loaded with different fractions of americium in the fuel, using the safety parameters obtained with the SERPENT Monte Carlo code. The focus is on americium mainly due to its long-term contribution to the radiotoxicity of spent nuclear fuel and its deterioration on c...

  10. Analysis of Americium in Transplutonium Process Solutions

    International Nuclear Information System (INIS)

    Ferguson, R.B.

    2001-01-01

    One of the more difficult analyses in the transplutonium field is the determination of americium at trace levels in a complex matrix such as a process dissolver solution. Because of these conditions a highly selective separation must precede the measurement of americium. The separation technique should be mechanically simple to permit remote operation with master-slave manipulators. For subsequent americium measurement by the mass spectroscopic isotopic-dilution technique, plutonium and curium interferences must also have been removed

  11. Luminescence study on solvation of americium(III), curium(III) and several lanthanide(III) ions in nonaqueous and binary mixed solvents

    International Nuclear Information System (INIS)

    Kimura, T.; Nagaishi, R.; Kato, Y.; Yoshida, Z.

    2001-01-01

    The luminescence lifetimes of An(III) and Ln(III) ions [An=Am and Cm; Ln=Nd, Sm, Eu, Tb and Dy] were measured in dimethyl sulfoxide(DMSO), N,N-dimethylformamide(DMF), methanol(MeOH), water and their perdeuterated solvents. Nonradiative decay rates of the ions were in the order of H 2 O > MeOH > DMF > DMSO, indicating that O-H vibration is more effective quencher than C-H, C=O, and S=O vibrations in the solvent molecules. Maximal lifetime ratios τ D /τ H were observed for Eu(III) in H 2 O, for Sm(III) in MeOH and DMF, and for Sm(III) and Dy(III) in DMSO. The solvent composition in the first coordination sphere of Cm(III) and Ln(III) in binary mixed solvents was also studied by measuring the luminescence lifetime. Cm(III) and Ln(III) were preferentially solvated by DMSO in DMSO-H 2 O, by DMF in DMF-H 2 O, and by H 2 O in MeOH-H 2 O over the whole range of the solvent composition. The order of the preferential solvation, i.e., DMSO > DMF > H 2 O > MeOH, correlates with the relative basicity of these solvents. The Gibbs free energy of transfer of ions from water to nonaqueous solvents was further estimated from the degree of the preferential solvation. (orig.)

  12. Metabolism of americium-241 in dairy animals

    International Nuclear Information System (INIS)

    Sutton, W.W.; Patzer, R.G.; Mullen, A.A.; Hahn, P.B.; Potter, G.D.

    1978-10-01

    Groups of lactating cows and goats were used to examine americium-241 metabolism in dairy animals. Following either single oral or intravenous nuclide doses, samples of milk, urine, blood, and feces were taken over a 168-hr collection period and the americium concentrations were determined by gamma counting. Gastrointestinal uptake of americium by both cows and goats was estimated to be 0.014% of the respective oral doses. The cumulative percentage of oral dose transported to milk and urine was 4.4 x 10 -4 and 1.1 x 10 -3 respectively for cows and 4.4 x 10 -3 and 1.2 x 10 -3 respectively for goats. The relatively high americium concentrations noted in caprine milk following the oral doses are discussed. Plasma concentrations of americium decreased rapidly following all intravenous injections. The average percentage of injected americium transferred to milk, urine, and feces was 3, 6, and 2% respectively for cows and 2, 4, and 2% respectively for goats. In both intravenously dosed groups, approximately 30% of all americium released from the body was found in the urine during the first 24 hrs after injection. All animals were sacrificed 8 to 9 days after dosing. Bovine bone retained the greatest fraction of the administered dose followed by the liver. However, liver retained the greatest amount of americium in the goats following both oral and intravenous doses. Comparisons are presented between americium-241 and plutonium-238 transport in dairy cows

  13. Metabolism of americium-241 in dairy animals

    International Nuclear Information System (INIS)

    Sutton, W.W.; Patzer, R.G.; Mullen, A.A.; Hahn, P.B.; Potter, G.D.

    1978-01-01

    Groups of lactating cows and goats were used to examine americium-241 metabolism in dairy animals. Following either single oral or intravenous nuclide doses, samples of milk, urine, blood, and feces were taken over a 168-hour collection period, and the americium concentrations were determined by gamma counting. Gastrointestinal uptake of americium by cows and goats was estimated to be 0.014 and 0.016% of the oral dose, respectively. The cumulative percentage of oral dose transported to milk and urine was 4.4 x 10 -4 and 1.1 x 10 -3 , respectively, for cows and 5.6 x 10 -4 and 1.2 x 10 -3 , respectively, for goats. Plasma concentrations of americium decreased rapidly following all intravenous injections. The average percentage of injected americium transferred to milk, urine, and feces was 3, 6, and 2%, respectively, for cows, and 2, 4, and 2%, respectively, for goats. In both intravenously dosed groups, approximately 30% of all americium released from the body was found in the urine during the first 24 hours after injection. All animals were sacrificed 8 to 9 days after dosing. Bovine bone retained the greatest fraction of the administered dose followed by liver and kidney. However, liver retained the greatest amount of americium in the goats following both oral and intravenous doses. Comparisons are presented between americium-241 and plutonium-238 transport in dairy cows

  14. Production of americium isotopes in France

    International Nuclear Information System (INIS)

    Koehly, G.; Bourges, J.; Madic, C.; Nguyen, T.H.; Lecomte, M.

    1984-12-01

    The program of productions of americium 241 and 243 isotopes is based respectively on the retreatment of aged plutonium alloys or plutonium dioxide and on the treatment of plutonium targets irradiated either in CELESTIN reactors for Pu-Al alloys or OSIRIS reactor for plutonium 242 dioxide. All the operations, including americium final purifications, are carried out in hot cells equipped with remote manipulators. The chemical processes are based on the use of extraction chromatography with hydrophobic SiO 2 impregnated with extracting agents. Plutonium targets and aged plutonium alloys are dissolved in nitric acid using conventional techniques while plutonium dioxide dissolutions are performed routine at 300 grams scale with electrogenerated silver II in 4M HNO 3 at room temperature. The separation between plutonium and americium is performed by extraction of Pu(IV) either on TBP/SiO 2 or TOAHNO 3 /SiO 2 column. Americium recovery from waste streams rid of plutonium is realized by chromatographic extraction of Am(III) using mainly TBP and episodically DHDECMP as extractant. The final purification of both americium isotopes uses the selective extraction of Am(VI) on HDDiBMP/SiO 2 column at 60 grams scale. Using the overall process a total amount of 1000 grams of americium 241 and 100 grams of americium 243 has been produced nowadays and the AmO 2 final product indicates a purity better than 98.5%

  15. Contributions to the preparation of 241americium metal and a few 241americium silicides

    International Nuclear Information System (INIS)

    Wittmann, F.D.

    1980-01-01

    In order to take a closer look at the americium-silicon system, three further silicides of americium: Am 5 Si 3 , Am 2 Si 3 and AmSi 2 were prepared in addition to the already known americium monosilicide and starting from the knowledge gained from the latters preparation. Radiographic investigations were carried out into the temperature region of 900 0 C. They showed no change of structure in the three compounds. It was possible to prepare residue-free americium metal by reducing AmF 3 with Si, whereby the SiF 4 formed can be easily separated off as volatile compound, and the Am metal is brought into a very pure form by sublimation suitable for spectrochemical investigations. Attempts to prepare binary germanides and gallides of 241 americium were unsuccessful. (RB) [de

  16. Americium thermodynamic data for the EQ3/6 database

    International Nuclear Information System (INIS)

    Kerrisk, J.F.

    1984-07-01

    Existing thermodynamic data for aqueous and solid species of americium have been reviewed and collected in a form that can be used with the EQ3/6 database. Data that are important in solubility calculations for americium at a proposed Yucca Mountain nuclear waste repository were emphasized. Conflicting data exist for americium complexes with carbonates. Essentially no data are available for americium solids or complexes at temperatures greater than 25 0 C. 17 references, 4 figures

  17. Aqueous Chloride Operations Overview: Plutonium and Americium Purification/Recovery

    Energy Technology Data Exchange (ETDEWEB)

    Kimball, David Bryan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Skidmore, Bradley Evan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-06-22

    Acqueous Chloride mission is to recover plutonium and americium from pyrochemical residues (undesirable form for utilization and storage) and generate plutonium oxide and americium oxide. Plutonium oxide is recycled into Pu metal production flowsheet. It is suitable for storage. Americium oxide is a valuable product, sold through the DOE-OS isotope sales program.

  18. Formation of americium and europium humate complexes

    International Nuclear Information System (INIS)

    Minai, Y.; Tominaga, T.; Meguro, Y.

    1991-01-01

    Binding constants of americium and europium with a humic acid were determined to study if complex formation of trivalent actinide-humates affects dissolved species of the actinides in hydrosphere. The purified humic acid was characterized by means of UV-vis, IR, and pH titration, indicating high carboxylate capacity and low aromaticity. Binding constants of americium and europium humates were determined at pH 4.6 and 6.0 by solvent extraction using 241 Am or 152 Eu as a tracer. The binding constants for americium-humate obtained preliminarily suggest that complexes with humic acid are not negligible in speciation of trivalent actinides in hydrosphere. The obtained binding constants were nearly identical with those determined previously by the same procedures, but with humic acids of different origin and compositions. (author)

  19. Transmutation of Americium in Fast Neutron Facilities

    International Nuclear Information System (INIS)

    Zhang, Youpeng

    2011-01-01

    In this thesis, the feasibility to use a medium sized sodium cooled fast reactor fully loaded with MOX fuel for efficient transmutation of americium is investigated by simulating the safety performance of a BN600-type fast reactor loaded with different fractions of americium in the fuel, using the safety parameters obtained with the SERPENT Monte Carlo code. The focus is on americium mainly due to its long-term contribution to the radiotoxicity of spent nuclear fuel and its deterioration on core's safety parameters. Applying the SAS4A/SASSYS transient analysis code, it is demonstrated that the power rating needs to be reduced by 6% for each percent additional americium introduction into the reference MOX fuel, maintaining 100 K margin to fuel melting, which is the most limiting failure mechanism. Safety analysis of a new Accelerator Driven System design with a smaller pin pitch-to-diameter ratio comparing to the reference EFIT-400 design, aiming at improving neutron source efficiency, was also performed by simulating performance for unprotected loss of flow, unprotected transient overpower, and protected loss-of-heat-sink transients, using neutronic parameters obtained from MCNP calculations. Thanks to the introduction of the austenitic 15/15Ti stainless steel with enhanced creep rupture resistance and acceptable irradiation swelling rate, the suggested ADS design loaded with nitride fuel and cooled by lead-bismuth eutectic could survive the full set of transients, preserving a margin of 130 K to cladding rupture during the most limiting transient. The thesis concludes that efficient transmutation of americium in a medium sized sodium cooled fast reactor loaded with MOX fuel is possible but leads to a severe power penalty. Instead, preserving transmutation rates of minor actinides up to 42 kg/TWh th , the suggested ADS design with enhanced proton source efficiency appears like a better option for americium transmutation

  20. Preparation of americium source for smoke detector

    International Nuclear Information System (INIS)

    Ramaswami, A.; Singh, R.J.; Manohar, S.B.

    1994-01-01

    This report describes the method developed for the preparation of 241 Am source for smoke detector. Americium was electrodeposited from iso-propyl alcohol medium on silver backing. Thin layer of gold (few hundred micro gram thick) was plated on the americium source to make it safe for handling. The thickness of plated gold was such that the alpha radiations from the 241 Am source could escape out of the gold layer and cause ionisation in the surrounding air. The performance of the prepared sources were checked in a smoke detector and was found to be satisfactory and comparable to the imported sources. (author). 1 refs., 2 figs., 1 tab

  1. Plutonium and americium extraction studies with bifunctional organophosphorus extractants

    International Nuclear Information System (INIS)

    Navratil, J.D.

    1985-01-01

    Neutral bifunctional organophosphorus extractants, such as octylphenyl-N,N-diisobutylcarbamoylmethylphosphine oxide (CMPO) and dihexyl-N,N-diethylcarbamoylmethylphosphonate (CMP), are under study at the Rocky Flats Plant (RFP) to remove plutonium and americium from the 7M nitric acid waste. These compounds extract trivalent actinides from strong nitric acid, a property which distinguishes them from monofunctional organiphosphorus reagents. Furthermore, the reagents extract hydroytic plutonium (IV) polymer which is present in the acid waste stream. The compounds extract trivalent actinides with a 3:1 stoichiometry, whereas tetra- and hexavalent actinides extract with a stoichiometry of 2:1. Preliminary studies indicate that the extracted plutonium polymer complex contains one to two molecules of CMP per plutonium ion and the plutonium(IV) maintains a polymeric structure. Recent studies by Horwitz and co-workers conclude that the CMPO and CMP reagents behave as monodentate ligands. At RFP, three techniques are being tested for using CMP and CMPO to remove plutonium and americium from nitric acid waste streams. The different techniques are liquid-liquid extraction, extraction chromatography, and solid-supported liquid membranes. Recent tests of the last two techniques will be briefly described. In all the experiments, CMP was an 84% pure material from Bray Oil Co. and CMPO was 98% pure from M and T Chemicals

  2. Plant uptake of americium, curium, and the chemical analog neodymium

    International Nuclear Information System (INIS)

    Weimer, W.C.; Laul, J.C.; Kutt, J.C.; Bondietti, E.A.

    1977-01-01

    The plant uptake from several bulk soils has been determined for neodymium, a chemical analog to the transuranium elements americium and curium, and several other native rare earth elements as well. These investigations have demonstrated that neodymium, which has very similar chemical properties to amercium and curium and should have a similar environmental behavior, does behave indistinguishably under both laboratory and field conditions. The uptake of the weathered or mobile forms of these elements from soils is expected to be governed primarily by their identical oxidation states and nearly identical ionic radii. This hypothesis is strongly supported by the chondritic (primordial) normalized rare earth element patterns in several plants. In these samples, the entire series of rare earth elements behaves as a smooth function of the REE ionic radii, as is also seen in the contiguous soils. This behavior suggests that the plant uptake of other ions with similar chemical properties (i.e., americium and curium) would also be governed by ionic size and charge

  3. Uptake and recovery of americium and uranium by Anacystis biomass

    International Nuclear Information System (INIS)

    Liu, H.H.; Jiunntzong Wu

    1993-01-01

    The optimum conditions for the uptake of americium and uranium from wastewater solutions by Anacystis nidulans cells, and the recovery of these radionuclides were studied. The optimum pH range for both actinides was in the acidic region between 3.0 and 5.0. In a pH 3.5 solution with an algal biomass of 70 μg/mL, up to 95% of the Am and U were taken up by the cells. However, the uptake levels were lowered considerably when ethylene dinitrilotetraacetic acid (EDTA) or iron or calcium ions were present in the solutions. Most of the radionuclides taken up by the cells could also be desorbed by washing with salt solutions. Of nine salt solutions tested, ammonium carbonate was the most effective. Our experiments using algal biomass to remove radionuclides from wastewater showed that about 92% of americium and 85% of uranium in wastewater could be taken up by algal biomass, from which about 46% of the Am and 82% of the U originally present in the wastewater could be recovered by elution with a salt solution. 17 refs., 7 figs., 2 tabs

  4. Redox chemistry of americium in nitric acid media

    Energy Technology Data Exchange (ETDEWEB)

    Picart, S.; Jobelin, I.; Armengol, G.; Adnet, JM

    2004-07-01

    The redox properties of the actinides are very important parameters for speciation studies and spent nuclear fuel reprocessing based on liquid-liquid extraction of actinides at different oxidation states (as in the Purex or Sesame process). They are also very useful for developing analytical tools including coulometry and redox titration. This study addressed the americium(IV)/americium(III) and americium(VI)/americium(V) redox couples, focusing on exhaustive acquisition of the thermodynamic and kinetic parameters of americium oxidation at an electrode in a complexing nitric acid medium. (authors)

  5. Redox chemistry of americium in nitric acid media

    International Nuclear Information System (INIS)

    Picart, S.; Jobelin, I.; Armengol, G.; Adnet, JM.

    2004-01-01

    The redox properties of the actinides are very important parameters for speciation studies and spent nuclear fuel reprocessing based on liquid-liquid extraction of actinides at different oxidation states (as in the Purex or Sesame process). They are also very useful for developing analytical tools including coulometry and redox titration. This study addressed the americium(IV)/americium(III) and americium(VI)/americium(V) redox couples, focusing on exhaustive acquisition of the thermodynamic and kinetic parameters of americium oxidation at an electrode in a complexing nitric acid medium. (authors)

  6. 1976 Hanford americium exposure incident: psychological aspects

    International Nuclear Information System (INIS)

    Brown, W.R.

    1982-01-01

    Accidents involving exposure to radiation or radioactive materials may involve an unusual degree of emotional trauma. Methods that may be employed in dealing with such trauma are discussed in relation to a specific accident in which a radiation worker was injured and seriously contaminated with americium-241

  7. Transmutation of americium in critical reactors

    International Nuclear Information System (INIS)

    Wallenius, J.

    2005-01-01

    Already in 1974, a Los Alamos report suggested that the recycling of higher actinides would be detrimental for the safety of critical reactors. Later investigations confirmed this understanding, and stringent limits on the fraction of minor actinides allowed to be present in the fuel of fast neutron reactors were established. In recent years, and in particular in connection with the generation IV initiative, it has been advocated that recycling of americium in critical reactors is not only feasible, but also a recommendable approach. In the present contribution, it is shown, to the contrary, that introduction of americium into reactors with uranium based fuels deteriorates the safety margin of these reactors to a degree that will not allow consumption of the americium sources present in any economically competitive nuclear fuel cycle. Further, it is shown that uranium and thorium free cores with plutonium based fuels may be designed, that features excellent safety characteristics, as long as americium is not present in the feed. Hence, a closed fuel cycle is suggested, that consists of commercial power production in light water reactors, plutonium burning in uranium and thorium free fast neutron critical reactors, and higher actinide consumption in accelerator driven systems with inert matrix fuel. It is argued that such a fuel cycle (being a refinement of the Double Strata fuel cycle proposed by JAERI and further developed by M. Salvatores) provides a minimum cost penalty for implementing P and T under realistic boundary conditions. (author)

  8. Decontaminaion of metals containing plutonium and americium

    International Nuclear Information System (INIS)

    Seitz, M.G.; Gerding, T.J.; Steindler, M.J.

    1979-06-01

    Melt-slagging (melt-refining) techniques were evaluated as a decontamination and consolidation step for metals contaminated with oxides of plutonium and americium. Experiments were performed in which mild steel, stainless steel, and nickel contaminated with oxides of plutonium and americium were melted in the presence of silicate slags of various compositions. The metal products were low in contamination, with the plutonium and americium strongly fractionated to the slags. Partition coefficients (plutonium in slag/plutonium in steel) of 7 x 10 6 were measured with boro-silicate slag and of 3 x 10 6 with calcium, magnesium silicate slag. Decontamination of metals containing as much as 14,000 ppM plutonium appears to be as efficient as for metals with plutonium levels of 400 ppM. Staged extraction, that is, a remelting of processed metal with clean slag, results in further decontamination of the metal. The second extraction is effective with either resistance-furnace melting or electric-arc melting. Slag adhering to the metal ingots and in defects within the ingots is in the important contributors to plutonium retained in processed metals. If these sources of plutonium are controlled, the melt-refining process can be used on a large scale to convert highly contaminated metals to homogeneous and compact forms with very low concentrations of plutonium and americium. A conceptual design of a melt-refining process to decontaminate plutonium- and americium-contaminated metals is described. The process includes single-stage refining of contaminated metals to produce a metal product which would have less than 10 nCi/g of TRU-element contamination. Two plant sizes were considered. The smaller conceptual plant processes 77 kg of metal per 8-h period and may be portable.The larger one processes 140 kg of metal per 8-h period, is stationary, and may be near te maximum size that is practical for a metal decontamination process

  9. Status of Americium-241 recovery at Rocky Flats Plant

    International Nuclear Information System (INIS)

    Knighton, J.B.; Hagan, P.G.; Navratil, J.D.; Thompson, G.H.

    1981-01-01

    This paper is presented in two parts: Part I, Molten Salt Extraction of Americium from Molten Plutonium Metal, and Part II, Aqueous Recovery of Americium from Extraction Salts. The Rocky Flats recovery process used for waste salts includes (1) dilute hydrochloric acid dissolution of residues; (2) cation exchange to convert from the chloride to the nitrate system and to remove gross amounts of monovalent impurities; (3) anion exchange separation of plutonium; (4) oxalate precipitation of americium; and (5) calcination of the oxalate at 600 0 C to yield americium oxide. The aqueous process portion describes attempts to improve the recovery of americium. The first part deals with modifications to the cation exchange step; the second describes development of a solvent extractions process that will recovery americium from residues containing aluminium as well as other common impurities. Results of laboratory work are described. 3 figures, 6 tables. (DP)

  10. Americium migration in basalt and implications to repository risk analysis

    International Nuclear Information System (INIS)

    Rickert, P.G.

    1980-01-01

    Experiments were performed with americium as a minor component in groundwater. Batch adsorption, migration through column, and filtration experiments were performed. It was determined in batch experiments that americium is strongly adsorbed from solution. It was determined with filtration experiments that large percentages of the americium concentrations suspended by the contact solutions in batch experiments and suspended by the infiltrating groundwater in migration experiments were associated with particulate. Filtration was determined to be the primary mode of removal of americium from infiltrating groundwater in a column of granulated basalt (20 to 50 mesh) and an intact core of permeable basalt. Fractionally, 0.46 and 0.22 of the americium component in the infiltrating groundwater was transported through the column and core respectively. In view of these filtration and migration experiment results, the concept of K/sub d/ in the chromatographic sense is meaningless for predicting americium migration in bedrock by groundwater transport at near neutral pH

  11. Procedure for the analysis of americium in complex matrices

    International Nuclear Information System (INIS)

    Knab, D.

    1978-02-01

    A radioanalytical procedure for the analysis of americium in complex matrices has been developed. Clean separations of americium can be obtained from up to 100 g of sample ash, regardless of the starting material. The ability to analyze large masses of material provides the increased sensitivity necessary to detect americium in many environmental samples. The procedure adequately decontaminates from rare earth elements and natural radioactive nuclides that interfere with the alpha spectrometric measurements

  12. Recovery and purification of americium from molten salt extraction residues

    International Nuclear Information System (INIS)

    Navratil, J.D.; Martella, L.L.; Thompson, G.H.

    1980-01-01

    Americium recovery and purification development at Rocky Flats involves the testing of a combined anion exchange - bidentate organophosphorus liquid - liquid extraction or extraction chromatography process for separating americium from molten salt extraction residues. Laboratory-scale and preliminary pilot-plant results have shown that americium can be effectively recovered and purified from impurity elements such as aluminum, calcium, magnesium, plutonium, potassium, sodium, and zinc. The purified americium oxide product from the liquid - liquid extraction process contained greater than 95% AmO 2 with less than 1% of any individual impurity element

  13. Development of analytical methods for the separation of plutonium, americium, curium and neptunium from environmental samples

    Energy Technology Data Exchange (ETDEWEB)

    Salminen, S.

    2009-07-01

    In this work, separation methods have been developed for the analysis of anthropogenic transuranium elements plutonium, americium, curium and neptunium from environmental samples contaminated by global nuclear weapons testing and the Chernobyl accident. The analytical methods utilized in this study are based on extraction chromatography. Highly varying atmospheric plutonium isotope concentrations and activity ratios were found at both Kurchatov (Kazakhstan), near the former Semipalatinsk test site, and Sodankylae (Finland). The origin of plutonium is almost impossible to identify at Kurchatov, since hundreds of nuclear tests were performed at the Semipalatinsk test site. In Sodankylae, plutonium in the surface air originated from nuclear weapons testing, conducted mostly by USSR and USA before the sampling year 1963. The variation in americium, curium and neptunium concentrations was great as well in peat samples collected in southern and central Finland in 1986 immediately after the Chernobyl accident. The main source of transuranium contamination in peats was from global nuclear test fallout, although there are wide regional differences in the fraction of Chernobyl-originated activity (of the total activity) for americium, curium and neptunium. The separation methods developed in this study yielded good chemical recovery for the elements investigated and adequately pure fractions for radiometric activity determination. The extraction chromatographic methods were faster compared to older methods based on ion exchange chromatography. In addition, extraction chromatography is a more environmentally friendly separation method than ion exchange, because less acidic waste solutions are produced during the analytical procedures. (orig.)

  14. Investigation of americium-241 metal alloys for target applications

    International Nuclear Information System (INIS)

    Conner, W.V.; Rockwell International Corp., Golden, CO

    1982-01-01

    Several 241 Am metal alloys have been investigated for possible use in the Lawrence Livermore National Laboratory Radiochemical Diagnostic Tracer Program. Several properties were desired for an alloy to be useful for tracer program applications. A suitable alloy would have a fairly high density, be ductile, homogeneous and easy to prepare. Alloys investigated have included uranium-americium, aluminium-americium, and cerium-americium. Uranium-americium alloys with the desired properties proved to be difficult to prepare, and work with this alloy was discontinued. Aluminium-americium alloys were much easier to prepare, but the alloy consisted of an aluminium-americium intermetallic compound (AmAl 4 ) in an aluminum matrix. This alloy could be cast and formed into shapes, but the low density of aluminum, and other problems, made the alloy unsuitable for the intended application. Americium metal was found to have a high solid solubility in cerium and alloys prepared from these two elements exhibited all of the properties desired for the tracer program application. Cerium-americium alloys containing up to 34 wt% americium have been prepared using both co-melting and co-reduction techniques. The latter technique involves co-reduction of cerium tetrafluoride and americium tetrafluoride with calcium metal in a sealed reduction vessel. Casting techniques have been developed for preparing up to eight 2.2 cm (0.87 in) diameter disks in a single casting, and cerium-americium metal alloy disks containing from 10 to 25 wt% 241 Am have been prepared using these techniques. (orig.)

  15. Influence of biofilms on migration of uranium, americium and europium in the environment; Einfluss von Biofilmen auf das Migrationsverhalten von Uran, Americium und Europium in der Umwelt

    Energy Technology Data Exchange (ETDEWEB)

    Baumann, Nils; Zirnstein, Isabel; Arnold, Thuro

    2015-07-01

    The report on the influence of biofilms on migration of uranium, americium and europium in the environment deals with the contamination problems of uranium mines such as SDAG WISMUT in Saxonia and Thuringia. In mine waters microorganisms form a complex microbiological biocoenosis in spite of low pH values and high heavy metal concentrations including high uranium concentrations. The analyses used microbiological methods like confocal laser scanning microscopy and molecular-biological techniques. The interactions of microorganism with fluorescent radioactive heavy metal ions were performed with TRLFS (time resolved laser-induced fluorescence spectroscopy).

  16. Investigation of factors affecting the quality of americium electroplating.

    Science.gov (United States)

    Trdin, M; Benedik, L; Samardžija, Z; Pihlar, B

    2012-09-01

    Four different electrolyte solutions were used in the electrodeposition of americium and their influences on the quality of the thin layer of deposited americium isotopes in combination with three different cathode disc materials were investigated. The relations between alpha spectral resolution and disc surface properties were established. Copyright © 2012 Elsevier Ltd. All rights reserved.

  17. Americium/curium bushing melter drain tests

    International Nuclear Information System (INIS)

    Smith, M.E.; Hardy, B.J.; Smith, M.E.

    1997-01-01

    Americium and curium were produced in the past at the Savannah River Site (SRS) for research, medical, and radiological applications. They have been stored in a nitric acid solution in an SRS reprocessing facility for a number of years. Vitrification of the americium/curium (Am/Cm) solution will allow the material to be safely stored or transported to the DOE Oak Ridge Reservation. Oak Ridge is responsible for marketing radionuclides for research and medical applications. The bushing melter technology being used in the Am/Cm vitrification research work is also under consideration for the stabilization of other actinides such as neptunium and plutonium. A series of melter drain tests were conducted at the Savannah River Technology Center to determine the relationship between the drain tube assembly operating variables and the resulting pour initiation times, glass flowrates, drain tube temperatures, and stop pour times. Performance criteria such as ability to start and stop pours in a controlled manner were also evaluated. The tests were also intended to provide support of oil modeling of drain tube performance predictions and thermal modeling of the drain tube and drain tube heater assembly. These drain tests were instrumental in the design of subsequent melter drain tube and drain tube heaters for the Am/Cm bushing melter, and therefore in the success of the Am/Cm vitrification and plutonium immobilization programs

  18. Investigation of factors affecting the quality of americium electroplating

    International Nuclear Information System (INIS)

    Trdin, M.; Benedik, L.; Samardžija, Z.; Pihlar, B.

    2012-01-01

    Four different electrolyte solutions were used in the electrodeposition of americium and their influences on the quality of the thin layer of deposited americium isotopes in combination with three different cathode disc materials were investigated. The relations between alpha spectral resolution and disc surface properties were established. - Highlights: ► Compared alpha spectra of americium radioisotopes obtained by electrodeposition. ► Various cathode materials and electrolyte solutions were used. ► Homogeneity and peak area resolution were investigated. ► Electron microscope images show surface structure of electrodeposited material.

  19. Measurement of plutonium and americium in molten salt residues

    International Nuclear Information System (INIS)

    Haas, F.X.; Lawless, J.L.; Herren, W.E.; Hughes, M.E.

    1979-01-01

    The measurement of plutonium and americium in molten salt residues using a segmented gamma-ray scanning device is described. This system was calibrated using artificially fabricated as well as process generated samples. All samples were calorimetered and the americium to plutonium content of the samples determined by gamma-ray spectroscopy. For the nine samples calorimetered thus far, no significant biases are present in the comparison of the segmented gamma-ray assay and the calorimetric assay. Estimated errors are of the order of 10 percent and is dependent on the americium to plutonium ratio determination

  20. Influence of biofilms on migration of uranium, americium and europium in the environment

    International Nuclear Information System (INIS)

    Baumann, Nils; Zirnstein, Isabel; Arnold, Thuro

    2015-01-01

    The report on the influence of biofilms on migration of uranium, americium and europium in the environment deals with the contamination problems of uranium mines such as SDAG WISMUT in Saxonia and Thuringia. In mine waters microorganisms form a complex microbiological biocoenosis in spite of low pH values and high heavy metal concentrations including high uranium concentrations. The analyses used microbiological methods like confocal laser scanning microscopy and molecular-biological techniques. The interactions of microorganism with fluorescent radioactive heavy metal ions were performed with TRLFS (time resolved laser-induced fluorescence spectroscopy).

  1. Behavior of americium in aqueous carbonate systems

    Energy Technology Data Exchange (ETDEWEB)

    Silva, R.J.

    1983-11-01

    The solubilities of crystalline Am(OH)/sub 3/ and AmOHCO/sub 3/ were measured at 25/sup 0/C in aqueous solutions of 0.1 M NaClO/sub 4/ by determination of the solution concentrations of Am. Prior to use in the measurements, the solid materials were characterized by their x-ray powder diffraction patterns. The solubility product quotients were calculated from the experimental data. The hydrolysis quotients of Am/sup 3 +/ were also estimated from the hydroxide solubility data. Using the thermodynamic data derived from these experiments and the recently reported formation constants for the Am/sup 3 +/ carbonate complexes, the solid phases and concentrations of solution species of americium in several aqueous carbonate systems were calculated using the computer code MINEQL. 20 references, 1 figure, 1 table.

  2. Uptake of americium-241 by algae and bacteria

    Energy Technology Data Exchange (ETDEWEB)

    Geisy, J P; Paine, D

    1978-01-01

    Algae and bacteria are important factors in the transport and mobilization of elements in the biosphere. These factors may be involved in trophic biomagnification, resulting in a potential human hazard or environmental degradation. Although americium, one of the most toxic elements known, is not required for plant growth, it may be concentrated by algae and bacteria. Therefore, the availability of americium-241 to algae and bacteria was studied to determine their role in the ultimate fate of this element released into the environment. Both algae and bacteria concentrated americium-241 to a high degree, making them important parts of the biomagnification process. The ability to concentrate americium-241 makes algae and bacteria potentially significant factors in cycling this element in the water column. (4 graphs, numerous references, 3 tables)

  3. PROCESS FOR SEPARATING AMERICIUM AND CURIUM FROM RARE EARTH ELEMENTS

    Science.gov (United States)

    Baybarz, R.D.; Lloyd, M.H.

    1963-02-26

    This invention relates to methods of separating americium and curium values from rare earth values. In accordance with the invention americium, curium, and rare earth values are sorbed on an anion exchange resin. A major portion of the rare earth values are selectively stripped from the resin with a concentrated aqueous solution of lithium chloride, and americium, curium, and a minor portion of rare earth values are then stripped from the resin with a dilute aqueous solution of lithium chloride. The americium and curium values are further purified by increasing the concentration of lithium chloride in the solution to at least 8 molar and selectively extracting rare earth values from the resulting solution with a monoalkylphosphoric acid. (AEC)

  4. Sorption of americium and neptunium by deep-sea sediments

    International Nuclear Information System (INIS)

    Higgo, J.J.W.; Rees, L.V.C.; Cronan, D.S.

    1983-01-01

    The sorption and desorption of americium and neptunium by a wide range of deep-sea sediments from natural sea water at 4 0 C has been studied using a carefully controlled batch technique. All the sediments studied should form an excellent barrier to the migration of americium since distribution coefficients were uniformly greater than 10 5 and the sorption-desorption reaction may not be reversible. The sorption of neptunium was reversible and, except for one red clay, the distribution coefficients were greater than 10 3 for all the sediments investigated. Nevertheless the migration of neptunium should also be effectively retarded by most deep-sea sediments even under relatively oxidizing conditions. The neptunium in solution remained in the V oxidation state throughout the experiments. Under the experimental conditions used colloidal americium was trapped by the sediment and solubility did not seem to be the controlling factor in the desorption of americium. (Auth.)

  5. Americium/Curium Disposition Life Cycle Planning Study

    International Nuclear Information System (INIS)

    Jackson, W.N.; Krupa, J.; Stutts, P.; Nester, S.; Raimesch, R.

    1998-01-01

    At the request of the Department of Energy Savannah River Office (DOE- SR), Westinghouse Savannah River Company (WSRC) evaluated concepts to complete disposition of Americium and Curium (Am/Cm) bearing materials currently located at the Savannah River Site (SRS)

  6. Comparative behavior of americium and plutonium in wastewater

    International Nuclear Information System (INIS)

    Tsvetaeva, N.E.; Filin, V.M.; Ragimov, T.K.; Rudaya, L.Y.; Shapiro, K.Y.; Shcherbakov, B.Y.

    1986-01-01

    This paper studies the behavior of trace americium and plutoniumin wastewater fed into purification systems. Activities of the elements were determined on a semiconductive alpha-ray spectrometer. the distributio nonuniformity, or heterogeneity, of americium and plutonium per unit volume of wastewater was determined quantitatively before and after passage through filter papers. The two elements were found to be in a colloidal or pseudocolloidal state in the original wastewater sample at pH 6. On acidifying the wastewater from pH 4 to 1 M nitric acid the americium passed quantitatively into the water phase but the most plutonium remained in the colloidal or pseudocolloidal state. the plutonium also passed quantitatively into the water phase in wastewater at a 1 M nitric acid acidity but only after a prolonged (12-day) hold. A knowledge of the heterogeneity of plutonium and americium in wastewaters made it possible to quickly distinguish their state, i.e., colloidal, pseudocolloidal, or in true solution

  7. Plutonium and Americium Geochemistry at Hanford: A Site Wide Review

    Energy Technology Data Exchange (ETDEWEB)

    Cantrell, Kirk J.; Felmy, Andrew R.

    2012-08-23

    This report was produced to provide a systematic review of the state-of-knowledge of plutonium and americium geochemistry at the Hanford Site. The report integrates existing knowledge of the subsurface migration behavior of plutonium and americium at the Hanford Site with available information in the scientific literature regarding the geochemistry of plutonium and americium in systems that are environmentally relevant to the Hanford Site. As a part of the report, key research needs are identified and prioritized, with the ultimate goal of developing a science-based capability to quantitatively assess risk at sites contaminated with plutonium and americium at the Hanford Site and the impact of remediation technologies and closure strategies.

  8. Remobilization of americium in soil columns under experimental rhizo-spheric conditions

    Energy Technology Data Exchange (ETDEWEB)

    Perrier, T.; Martin-Garin, A.; Morello, M. [CEA Cadarache (DEI/SECRE/LRE), Laboratory of Radioecology and Ecotoxicology, Institute for Radioprotection and Nuclear Safety, 13 - Saint-Paul-lez-Durance (France)

    2004-07-01

    The biogeochemical behaviour of americium in subsurface soils plays a dominant role on the potential migration of this actinide, but is currently poorly known. The identification and understanding of these processes is of major concern for this highly (radio)toxic element and can allow the determination of its impact on the natural media. This research investigates the relevant processes controlling americium biogeochemical speciation in the rhizosphere of an agricultural soil. Lixiviation tests were performed on columns packed with a 2 mm-sieved calcareous soil contaminated with {sup 241}Am (500 Bq.g{sup -1}), under steady-state unsaturated or saturated hydric flow conditions. The columns were percolated with soil solution of varied compositions, containing citrate and/or glucose simulating root exudates in non-sterile conditions. The physico-chemical parameters of the outlet solution (pH, conductivity, major ions, organic acids) were monitored, as well as the microbial activity. Inorganic and organic speciation of {sup 241}Am is supported by geochemical modeling with JChess, using a thermodynamic database based on NEA database and the latest PSI recommendations. The percolation of a solution in equilibrium with the soil released small amount of americium (<5 mBq/cm{sup 3}), as predicted by the high {sup 241}Am K{sub d} values. 10{sup -4} M concentrations of citrate, glucose or both combined did not enhance remobilization either. Poor remobilization was also observed at high glucose concentrations (10{sup -2} M), despite an effective glucose microbial degradation, the production of ligands such as acetate, and important changes in the chemistry of the solution. On the contrary, high concentrations of citrate (10{sup -2} M) released 1000 times more americium, which is in accordance with previous studies. Even greater releases (10000 times) were observed when 10{sup -2} M glucose was added to 10{sup -2} M citrate. The remobilization of americium resulting from the

  9. Aqueous Chloride Operations Overview: Plutonium and Americium Purification/Recovery

    Energy Technology Data Exchange (ETDEWEB)

    Gardner, Kyle Shelton [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Kimball, David Bryan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Skidmore, Bradley Evan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-09-28

    These are a set of slides intended for an information session as part of recruiting activities at Brigham Young University. It gives an overview of aqueous chloride operations, specifically on plutonium and americium purification/recovery. This presentation details the steps taken perform these processes, from plutonium size reduction, dissolution, solvent extraction, oxalate precipitation, to calcination. For americium recovery, it details the CLEAR (chloride extraction and actinide recovery) Line, oxalate precipitation and calcination.

  10. Pyrochemical investigations into recovering plutonium from americium extraction salt residues

    International Nuclear Information System (INIS)

    Fife, K.W.; West, M.H.

    1987-05-01

    Progress into developing a pyrochemical technique for separating and recovering plutonium from spent americium extraction waste salts has concentrated on selective chemical reduction with lanthanum metal and calcium metal and on the solvent extraction of americium with calcium metal. Both techniques are effective for recovering plutonium from the waste salt, although neither appears suitable as a separation technique for recycling a plutonium stream back to mainline purification processes. 17 refs., 13 figs., 2 tabs

  11. 1976 Hanford americium-exposure incident: external decontamination procedures

    International Nuclear Information System (INIS)

    Jech, J.J.; Berry, J.R.; Breitenstein, B.D.

    1982-01-01

    An accident resulted in the deposition on an injured workman's skin surfaces, in acid-burned areas and in lacerations, of something in excess of 6 mCi americium-241. The external decontamination procedures used, the change in americium content of the skin during the course of treatment, and some of the unusual problems encountered from the extrusion of foreign material and flaking of skin and scar tissue are described

  12. Citric complexes, neodymium citrate and americium citrate

    International Nuclear Information System (INIS)

    Bouhlassa, Saidati.

    1981-06-01

    The behaviour of neodymium and americium has been studied in citric aqueous medium by two methods: solvent extraction of elements at tracer scale as chelates and by potentiometry. So range of pH and concentrations of elements and citric acid never reached before have been explored: 10 -7 -1 M, 10 -10 -3 , Csub(H3 Cit) -1 M, 1 2 O; AmCit, xH 2 O; NdCit 2 Co(NH 3 ) 6 , 8H 2 O; AmCit 2 Co(NH 3 ) 6 , xH 2 O and Nd 3 (OH) 4 (Cit) 4 NH 4 (Co(NH 3 ) 6 ) 2 , 18H 2 O. Their spectroscopic and crystallographic characteristics have been listed and studied. The nephelauxetic effect has been estimated from citric complexes as well as from citrates of these elements. The structure of the complexes in solution has been discussed on the basis of analysis of hypersensitive transition in different complexes [fr

  13. Biosorption of americium-241 by Candida sp

    International Nuclear Information System (INIS)

    Luo Shunzhong; Zhang Taiming; Liu Ning; Yang Yuanyou; Jin Jiannan; Liao Jiali

    2003-01-01

    As an important radioisotope in nuclear industry and other fields, americium-241 is one of the most serious contamination concerns duo to its high toxicity and long half-life. In this experiment, the biosorption of 241 Am from solution by Candida sp., and the effects of various experimental conditions on the adsorption were investigated. The preliminary results showed that the adsorption of 241 Am by Candida sp. was efficient. 241 Am could be removed by Candida sp. of 0.82 g/L (dry weight) from 241 Am solutions of 5.6-111 MBq/L (44.3-877.2 μg/L)(C 0 ), with maximum adsorption rate (R) of 98% and maximum adsorption capacities (W) of 63.5 MBq/g biomass (dry weight) (501.8 μg/g). The biosorption equilibrium was achieved within 4 hour and the optimum pH was pH = 2. No significant differences on 241 Am adsorption were observed at 10 C-45 C, or in solutions containing Au 3+ or Ag + , even 1500 times or 4500 times above the 241 Am concentration, respectively. The relationship between concentrations and adsorption capacities of 241 Am indicated the biosorption process should be described by a Langmuir adsorption isotherm. (orig.)

  14. Americium-curium vitrification process development

    International Nuclear Information System (INIS)

    Fellinger, A.P.; Baich, M.A.; Hardy, B.J

    1999-01-01

    The successful demonstration of sequentially drying, calcining and vitrifying an oxalate slurry in the Drain Tube Test Stand (DTTS) vessel provided the process basis for testing on a larger scale in a cylindrical induction heated melter. A single processing issue, that of batch volume expansion, was encountered during the initial stage of testing. The increase in batch volume centered on a sintered frit cap and high temperature bubble formation. The formation of a sintered frit cap expansion was eliminated with the use of cullet. Volume expansions due to high temperature bubble formation (oxygen liberation from cerium reduction) were mitigated in the DTTS melter vessel through a vessel temperature profile that effectively separated the softening point of the glass cullet and the evolving oxygen from cerium reduction. An increased processing temperature of 1,470 C and a two hour hold time to find any remaining bubbles successfully reduced bubbles in the poured glass to an acceptable level. The success of the preliminary process demonstrations provided a workable process basis that was directly applicable to the newly installed Cylindrical Induction Melter (CIM) system, making the batch flowsheet the preferred option for vitrification of the americium-curium surrogate feed stream

  15. Synergistic extraction behaviour of americium from simulated acidic waste solutions

    International Nuclear Information System (INIS)

    Pathak, P.N.; Veeraraghavan, R.; Mohapatra, P.K.; Manchanda, V.K.

    1998-01-01

    The extraction behaviour of americium has been investigated with mixtures of 3-phenyl-4-benzoyl-5-isoxazolone (PBI) and oxodonors viz. tri-n-butyl phosphate (TBP), tri-n-octyl phosphine oxide (TOPO) and di-n-butyl octanamide (DBOA) using dodecane as the diluent from 1-6 M HNO 3 media. It is observed that D Am remains unaltered with PBI concentration (in the range 0.06-0.1 M) at 1.47 M TBP in the entire range of HNO 3 concentration. PBI and TBP in combination appears more promising compared to other synergistic systems. The possibility of using this mixture for americium removal from high level liquid waste solution has been explored. Extraction studies indicated that prior removal of uranium by 20% TBP in dodecane is helpful in the quantitative recovery of americium in three contacts. Effect of lanthanides on D Am is found to be marginal. (orig.)

  16. Uptake of americium-241 by algae and bacteria

    Energy Technology Data Exchange (ETDEWEB)

    Giesy, Jr, J P; Paine, D [Savannah River Ecology Lab., Aiken, S.C. (USA)

    1978-01-01

    The uptake of americium by three algae, Scenedesmus obliguus, Selenastrum capricomutum and Chlorella pyrenosdosa and a bacterium Aeromonas hydrophila was studied. Live and fixed cells of each algal species and live bacterial cells were used. It is shown that algae and bacteria concentrate americium 241 to a high degree which makes them important links in the biomagnification phenomenon which may ultimately lead to a human hazard and be potentially important in recycling Am /sup 241/ in the water column and mobilization from sediments. Chemical fixation of algal cells caused increased uptake which indicated that uptake is by passive diffusion and probably due to chemical alteration of surface binding sites.

  17. The ingestion of plutonium and americium by range cattle

    International Nuclear Information System (INIS)

    Blincoe, C.; Bohman, V.R.; Smith, D.D.

    1981-01-01

    The intake of plutonium and americium in the diet of cattle grazing on plutonium contaminated desert range was determined. Daily feed intake of the grazing animals was also determined so that the amount of nuclides ingested daily could be ascertained. Soil ingested by range cattle constituted the principal and possibly only source of ingested plutonium and americium and resulted in a daily intake of 3600-6600 pCi 238 Pu, 85,000-400,000 pCi 239 Pu, and 11,000-31,000 pCi 241 Am daily. Determining transuranic intake by direct measurement and from the composition and contamination of the diet gave identical results. (author)

  18. Method of isolation of traces of americium by using the +6 oxidation state properties

    International Nuclear Information System (INIS)

    Kwinta, Jean; Michel, Jean-Jacques

    1969-05-01

    The authors present a method to separate traces of americium from a solution containing fission products and actinides. This method comprises the following steps: firstly, the oxidation of americium at the +6 state by ammonium persulfate and carrying over of actinides and III and IV lanthanides by lanthanum fluoride; secondly, the reduction by hydrazine of the oxidized americium and carrying over of the reduced americium by lutetium fluoride; and thirdly, the americium-lutetium separation by selective extractions either with di 2 ethyl hexyl phosphoric acid, or by fractionated elution on an anionic resin column by a mixture of nitric acid and methanol [fr

  19. On the role of different biocomponents of bile and excretions in the elimination of plutonium and americium from the body

    International Nuclear Information System (INIS)

    Shvydko, N.S.

    1986-01-01

    A study was made of the role of biocomponents of bile, urine and feces in the elimination of plutonium and americium from the organism. Plutonium 239 and americium 241 were separated in bile due to higher tropism of plutonium to low molecular weight addends, and of americium, to a protein-containing fraction. The status of plutonium excreted in feces was the same as the physicochemical status of americium. Plutonium 239 and americium 241 eliminated in urine were in a completely ultrafiltered state

  20. 1976 Hanford americium exposure incident: overview and perspective

    International Nuclear Information System (INIS)

    Thompson, R.C.

    1982-01-01

    Salient features of the 1976 Hanford americium exposure incident are discussed. Comparisons are made with previous human and animal exposure data, and conclusions drawn relative to the injured workman, to health physics practices, and to the adequacy of current exposure limits

  1. Thermodynamic systematics of oxides of americium, curium, and neighboring elements

    International Nuclear Information System (INIS)

    Morss, L.R.

    1984-01-01

    Recently-obtained calorimetric data on the sesquioxides and dioxides of americium and curium are summarized. These data are combined with other properties of the actinide elements to elucidate the stability relationships among these oxides and to predict the behavior of neighboring actinide oxides. 45 references, 4 figures, 5 tables

  2. Research program on development of advanced treatment technology for americium-containing aqueous waste in NUCEF

    Energy Technology Data Exchange (ETDEWEB)

    Mineo, Hideaki; Matsumura, Tatsuro; Tsubata, Yasuhiro [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1996-10-01

    A research program was prepared on the development of an advanced treatment process for the americium-containing concentrated aqueous waste in NUCEF, than allows americium recovery for the reuse and the reduction of TRU waste generation. A preliminary analysis was conducted on the separation requirements based on the components estimated for the waste. An R and D strategy was proposed from the view to reduce TRU waste generated in the processing that the highest priority is given on the control of TRU leakage such as americium into the effluent stream after americium recovery and the minimization of salt used in the separation over the decontamination of impurities from americium. The extraction chromatographic method was selected as a candidate technology for americium separation under the principle to use reagents that are functional in acidic conditions such as bidentate extractants of DHEDECMP, CMPO or diamides, considering the larger flexibilities in process modification and possible multi-component separation with compact equipment and the past achievements on the recovery of kg quantities of americium. Major R and D items extracted are screening and evaluation of extractants for americium and plutonium, optimization of separation conditions, selection of denitration method, equipment developments and development of solidification methods of discarded americium after reuse and of various kinds of separation residues. In order to cope these items, four steps of R and D program were proposed, i.e., fundamental experiment in beaker-scale on screening and evaluation of extractants, flowsheet study in bench-scale using simulated and small amount of americium aqueous waste solution to evaluate candidate process, americium recovery test in iron-shielded cell to be installed in NUCEF. It is objected to make recovery of 100g orders of americium used for research on fundamental TRU fuel properties. (J.P.N.)

  3. Separation of Americium from plutonium, Annex 3; Prilog 3: Odvajanje amercijuma od plutonijuma

    Energy Technology Data Exchange (ETDEWEB)

    Cvjeticanin, D; Milic, N; Janicijevic, P; Ratkovic, S [Institute of Nuclear Sciences Boris Kidric, Laboratorija za visoku aktivnost, Vinca, Beograd (Serbia and Montenegro)

    1963-12-15

    Since there was the possibility of working with plutonium milligram quantities, it was possible to study plutonium with contents of americium, which was expected in the about two years old plutonium solutions. Method for separation of the micro quantities of americium and plutonium was needed as well as a multichannel alpha-pulse analyzer. Method for separation of americium from plutonium by thenol trifluoro-acetone (TTA) and anion exchange was adopted.

  4. Transfer of environmental plutonium and americium across the human gut

    International Nuclear Information System (INIS)

    Hunt, G.J.; Leonard, D.R.P.; Lovett, M.B.

    1989-01-01

    Following the ingestion of winkles obtained from a coastal area near Sellafield nuclear reprocessing plant, a group of volunteers provided urine for the next 7 days to be analysed for plutonium and americium. From this, estimates of the intake and gut transfer factors for these isotopes were determined. Preliminary estimates of gut transfer factors from a previous study by the same authors were then re-interpreted and combined with the results from the present study. (UK)

  5. 1976 Hanford americium-exposure incident: decontamination and treatment facility

    International Nuclear Information System (INIS)

    Berry, J.R.; McMurray, B.J.; Jech, J.J.; Breitenstein, B.D.; Quigley, E.J.

    1982-01-01

    An injured worker, contaminated with over 6 mCi of americium-241, required special treatment and housing for 4 months. This paper is a description of the design and management of the facility in which most of the treatment and housing occurred. The problems associated with contamination control, waste handling, supplies, and radiological concerns during the two-stage transfer of the patient from a controlled situation to his normal living environment are discussed in detail

  6. Ingestion Pathway Transfer Factors for Plutonium and Americium

    International Nuclear Information System (INIS)

    Blanchard, A.

    1999-01-01

    Overall transfer factors for major ingestion pathways are derived for plutonium and americium. These transfer factors relate the radionuclide concentration in a given foodstuff to deposition on the soil. Equations describing basic relationships consistent with Regulatory Guide 1.109 are followed. Updated values and coefficients from IAEA Technical Reports Series No. 364 are used when a available. Preference is given to using factors specific to the Savannah River Site

  7. Extraction separation of americium and curium. A review

    International Nuclear Information System (INIS)

    Petrzilova, H.

    1976-11-01

    A survey is given of extraction systems suitable for transplutonium element separation and preparation as well as for the practical application of their nuclear properties. Methods are discussed in detail of separating the actinide and the lanthanide fractions from fission and corrosion products and of separating americium from curium. The description is completed with flowsheets showing the separation of transplutonium elements from irradiated targets and waste solutions after spent fuel reprocessing. (L.K.)

  8. Americium-241: the most useful isotope of the actinide elements

    International Nuclear Information System (INIS)

    Navratil, J.D.

    1984-01-01

    Used extensively in nuclear gauges and in many other areas, this man-made element (Atomic Number 95) was first isolated in weighable amounts during World War II. Americium is now a very useful by-product of the nuclear industry and is produced in kilogram amounts by appropriate recovery, separation and purification processes. A review will be presented of its discovery, nuclear and chemical properties, and uses, with emphasis on its production process and separations chemistry

  9. Supercritical Fluid Extraction of Plutonium and Americium from Soil

    International Nuclear Information System (INIS)

    Fox, R.V.; Mincher, B.J.

    2002-01-01

    Supercritical fluid extraction (SFE) of plutonium and americium from soil was successfully demonstrated using supercritical fluid carbon dioxide solvent augmented with organophosphorus and beta-diketone complexants. Spiked Idaho soils were chemically and radiologically characterized, then extracted with supercritical fluid carbon dioxide at 2,900 psi and 65 C containing varying concentrations of tributyl phosphate (TBP) and thenoyltrifluoroacetone (TTA). A single 45 minute SFE with 2.7 mol% TBP and 3.2 mol% TTA provided as much as 88% ± 6.0 extraction of americium and 69% ± 5.0 extraction of plutonium. Use of 5.3 mol% TBP with 6.8 mol% of the more acidic beta-diketone hexafluoroacetylacetone (HFA) provided 95% ± 3.0 extraction of americium and 83% ± 5.0 extraction of plutonium in a single 45 minute SFE at 3,750 psi and 95 C. Sequential chemical extraction techniques were used to chemically characterize soil partitioning of plutonium and americium in pre-SFE soil samples. Sequential chemical extraction techniques demonstrated that spiked plutonium resides primarily (76.6%) in the sesquioxide fraction with minor amounts being absorbed by the oxidizable fraction (10.6%) and residual fractions (12.8%). Post-SFE soils subjected to sequential chemical extraction characterization demonstrated that 97% of the oxidizable, 78% of the sesquioxide and 80% of the residual plutonium could be removed using SFE. These preliminary results show that SFE may be an effective solvent extraction technique for removal of actinide contaminants from soil

  10. Extraction of americium from acid aqueous solutions by diethyl-2-hexyl-pyro-phosphoric acid

    International Nuclear Information System (INIS)

    Guillaume, Bernard

    1971-02-01

    After having outlined the interesting properties of americium and the difficulties of its recovery, the author reports the study of the mechanism of extraction of americium from acid aqueous solutions by using the diethyl-2hexyl-pyro-phosphoric acid. Several aspects are thus discussed: influence of concentration of H 2 DEHPP, influence of the acidity of the aqueous phase, saturation of extracting agent, influence of the diluting agent, complexing of americium, influence of other cations. In a second part, the author reports the application to the recovery of americium from effluents, and discusses the obtained results

  11. Americium Separations from High-Salt Solutions Using Anion Exchange

    International Nuclear Information System (INIS)

    Barr, Mary E.; Jarvinen, Gordon D.; Stark, Peter C.; Chamberlin, Rebecca M.; Bartsch, Richard A.; Zhang, Z.Y.; Zhao, W.

    2001-01-01

    The aging of the US nuclear stockpile presents a number of challenges, including the increasing radioactivity of plutonium residues due to the ingrowth of 241 Am from the β-decay of 241 Pu. We investigated parameters that affect the sorption of Am onto anion-exchange resins from concentrated effluents derived from nitric acid processing of plutonium residues. These postevaporator wastes are nearly saturated solutions of acidic nitrate salts, and americium removal is complicated by physical factors, such as solution viscosity and particulates, as well as by the presence of large quantities of competing metals and acid. Single- and double-contact batch distribution coefficients for americium and neodymium from simple and complex surrogate solutions are presented. Varied parameters include the nitrate salt concentration and composition and the nitric acid concentration. We find that under these extremely concentrated conditions, Am(III) removal efficiencies can surpass 50% per contact. Distribution coefficients for both neodymium and americium are insensitive to solution acidity and appear to be driven primarily by low water activities of the solutions

  12. Gut uptake factors for plutonium, americium and curium

    International Nuclear Information System (INIS)

    Harrison, J.D.

    1982-01-01

    Data on estimates of the absorption of plutonium, americium and curium from the human gut based on measurements of uptake in other mammalian species are reviewed. It is proposed that for all adult members of the public ingesting low concentrations of plutonium in food and water, 0.05% would be an appropriate value of absorption except when the conditions of exposure are known and a lower value can be justified. For dietary intakes of americium and curium, the available data do not warrant a change from the ICRP value of 0.05%. For newborn children ingesting americium, curium and soluble forms of plutonium, a value of 1% absorption is proposed for the first 3 months of life during which the infant is maintained on a milk diet. It is proposed that a value of 0.5% should be used for the first year of life to take account of the gradual maturation of the gut. In considering the ingestion of insoluble oxides of plutonium by infants, it is proposed that absorption is taken as 0.1% for the first 3 months and 0.05% for the first year. (author)

  13. On the structure of thorium and americium adenosine triphosphate complexes

    International Nuclear Information System (INIS)

    Mostapha, Sarah; Berton, Laurence; Boubals, Nathalie; Zorz, Nicole; Charbonnel, Marie-Christine; Fontaine-Vive, Fabien; Den Auwer, Christophe; Solari, Pier Lorenzo

    2014-01-01

    The actinides are chemical poisons and radiological hazards. One challenge to better appraise their toxicity and develop countermeasures in case of exposure of living organisms is to better assess pathways of contamination. Because of the high chemical affinity of those actinide elements for phosphate groups and the ubiquity of such chemical functions in biochemistry, nucleotides and in particular adenosine triphosphate nucleotide (ATP) may be considered critical target building blocks for actinides. Combinations of spectroscopic techniques (Fourier transformed Infra Red [FTIR], Electro-spray Ionization Mass Spectrometry [ESI-MS], and Extended X-ray Absorption Fine Structure [EXAFS]) with quantum chemical calculations have been implemented in order to assess the actinides coordination arrangement with ATP. We describe and compare herein the interaction of ATP with thorium and americium; thorium(IV) as a representative of actinide(IV) like plutonium(IV) and americium(III) as a representative of all heavier actinides. In the case of thorium, an insoluble complex is readily formed. In the case of americium, a behavior identical to that described previously for lutetium has been observed with insoluble and soluble complexes. The comparative study of ATP complexation with Th(IV) and Am(III) shows their ability to form insoluble complexes for which a structural model has been proposed by analogy with previously described Lu(III) complexes. (authors)

  14. On the structure of thorium and americium adenosine triphosphate complexes.

    Science.gov (United States)

    Mostapha, Sarah; Fontaine-Vive, Fabien; Berthon, Laurence; Boubals, Nathalie; Zorz, Nicole; Solari, Pier Lorenzo; Charbonnel, Marie Christine; Den Auwer, Christophe

    2014-11-01

    The actinides are chemical poisons and radiological hazards. One challenge to better appraise their toxicity and develop countermeasures in case of exposure of living organisms is to better assess pathways of contamination. Because of the high chemical affinity of those actinide elements for phosphate groups and the ubiquity of such chemical functions in biochemistry, nucleotides and in particular adenosine triphosphate nucleotide (ATP) may be considered critical target building blocks for actinides. Combinations of spectroscopic techniques (Fourier transformed Infra Red [FTIR], Electrospray Ionization Mass Spectrometry [ESI-MS], and Extended X-ray Absorption Fine Structure [EXAFS]) with quantum chemical calculations have been implemented in order to assess the actinides coordination arrangement with ATP. We describe and compare herein the interaction of ATP with thorium and americium; thorium(IV) as a representative of actinide(IV) like plutonium(IV) and americium(III) as a representative of all heavier actinides. In the case of thorium, an insoluble complex is readily formed. In the case of americium, a behavior identical to that described previously for lutetium has been observed with insoluble and soluble complexes. The comparative study of ATP complexation with Th(IV) and Am(III) shows their ability to form insoluble complexes for which a structural model has been proposed by analogy with previously described Lu(III) complexes.

  15. Americium-241 radioisotope thermoelectric generator development for space applications

    International Nuclear Information System (INIS)

    Ambrosi, Richard; Williams, Hugo; Samara-Ratna, Piyal

    2013-01-01

    Space nuclear power systems are under development in the UK in collaboration with European partners as part of a European Space Agency (ESA) programme. Radioisotope thermoelectric generators (RTG) are an important element of this new capability in Europe. RTG systems being developed in Europe are targeting the 10 W electric to 50 W electric power generation range adopting a modular scalable approach to the design. Radiogenic decay heat from radioisotopes can be converted to electrical power by using appropriate semiconductor based thermoelectric materials. The plan for Europe is to develop radioisotope space nuclear power systems based on both thermoelectric and Stirling power conversion systems. Although primarily focused on delivering up to 50 W of electrical power, the European radioisotope thermoelectric system development programme is targeting americium-241 as a fuel source and is maximizing the use of commercially available thermoelectric manufacturing processes in order to accelerate the development of power conversion systems. The use of americium provides an economic solution at high isotopic purity and is product of a separation process from stored plutonium produced during the reprocessing of civil nuclear fuel. A laboratory prototype that uses electrical heating as a substitute for the radioisotope was developed to validate the designs. This prototype has now been tested. This paper outlines the requirements for a European americium-241 fuelled RTG, describes the most recent updates in system design and provides further insight into recent laboratory prototype test campaigns. (author)

  16. Americium-241 radioisotope thermoelectric generator development for space applications

    Energy Technology Data Exchange (ETDEWEB)

    Ambrosi, Richard; Williams, Hugo; Samara-Ratna, Piyal, E-mail: rma8@le.ac.uk [University of Leicester, (United Kingdom); and others

    2013-07-01

    Space nuclear power systems are under development in the UK in collaboration with European partners as part of a European Space Agency (ESA) programme. Radioisotope thermoelectric generators (RTG) are an important element of this new capability in Europe. RTG systems being developed in Europe are targeting the 10 W electric to 50 W electric power generation range adopting a modular scalable approach to the design. Radiogenic decay heat from radioisotopes can be converted to electrical power by using appropriate semiconductor based thermoelectric materials. The plan for Europe is to develop radioisotope space nuclear power systems based on both thermoelectric and Stirling power conversion systems. Although primarily focused on delivering up to 50 W of electrical power, the European radioisotope thermoelectric system development programme is targeting americium-241 as a fuel source and is maximizing the use of commercially available thermoelectric manufacturing processes in order to accelerate the development of power conversion systems. The use of americium provides an economic solution at high isotopic purity and is product of a separation process from stored plutonium produced during the reprocessing of civil nuclear fuel. A laboratory prototype that uses electrical heating as a substitute for the radioisotope was developed to validate the designs. This prototype has now been tested. This paper outlines the requirements for a European americium-241 fuelled RTG, describes the most recent updates in system design and provides further insight into recent laboratory prototype test campaigns. (author)

  17. Airborne plutonium-239 and americium-241 concentrations measured from the 125-meter Hanford Meteorological Tower

    International Nuclear Information System (INIS)

    Sehmel, G.A.

    1978-01-01

    Airborne plutonium-239 and americium-241 concentrations and fluxes were measured at six heights from 1.9 to 122 m on the Hanford meteorological tower. The data show that plutonium-239 was transported on nonrespirable and small particles at all heights. Airborne americium-241 concentrations on small particles were maximum at the 91 m height

  18. Migration study of americium in porous medium

    International Nuclear Information System (INIS)

    Tanaka, Tadao; Ogawa, Hiromichi

    1999-01-01

    Migration experiments of 241 Am 3+ had been performed by a column system, to investigate migration behavior of 241 Am through a column packed porous sedimentary materials: a coastal sandy soil and a reddish soil. Most 241 Am loaded into the column packed the reddish soil sorbed on the influent edge of the column. In the case of the sandy soil, however, considerable amount of 241 Am was passed through the column. This shows that there is colloidal 241 Am species which may move without effective interaction with the sandy soil. Such a migration behavior of colloidal 241 Am in the sandy soil column could be evaluated by a sorption model based on filtration theory. Sorption mechanisms of 241 Am on the sedimentary materials were examined by a chemical extraction method, for 241 Am sorbed on the sandy soil and the reddish soil at any sections in the column. The 241 Am sorbed on the reddish soil was mainly controlled by a reversible ion exchange reaction. On the other hand, the 241 Am sorbed on the sandy soil ws controlled by irreversible reactions, such as the selective chemical sorptions onto Fe and Mn oxyhydroxide/oxide. The experimental results support that the migration of 241 Am in the reddish soil layer can be estimated by using the K d , whereas that in the sandy soil can not be explained by the K d concept. (author)

  19. The transmutation of americium: the Ecrix experiments in Phenix

    International Nuclear Information System (INIS)

    Garnier, J.C.; Schmidt, N.; Croixmarie, Y.; Ottaviani, J.P.; Varaine, F.; Saint Jean, C. de

    1999-01-01

    The first americium transmutation experiment in a specific target in PHENIX will occur with the ECRIX-B and ECRIX-H experiments. Beside material testing, the objective is also to represent a concept of transmutation whose specificity is to enhance the kinetics of transmutation by using a moderated spectrum. The moderator materials will be 11 B 4 C and CaH 2 for ECRIX-B and ECRIXH respectively, the irradiation conditions have been predicted for both the neutronics and thermal. The targets (MgO-AmO X pellets) are manufactured in the ATALANTE laboratory and the design is performed according to the PHENIX operating conditions. (authors)

  20. Robotic sample preparation for radiochemical plutonium and americium analyses

    International Nuclear Information System (INIS)

    Stalnaker, N.; Beugelsdijk, T.; Thurston, A.; Quintana, J.

    1985-01-01

    A Zymate robotic system has been assembled and programmed to prepare samples for plutonium and americium analyses by radioactivity counting. The system performs two procedures: a simple dilution procedure and a TTA (xylene) extraction of plutonium. To perform the procedures, the robotic system executes 11 unit operations such as weighing, pipetting, mixing, etc. Approximately 150 programs, which require 64 kilobytes of memory, control the system. The system is now being tested with high-purity plutonium metal and plutonium oxide samples. Our studies indicate that the system can give results that agree within 5% at the 95% confidence level with determinations performed manually. 1 ref., 1 fig., 1 tab

  1. Effect of 241-americium on bone marrow stroma

    International Nuclear Information System (INIS)

    Heuvel, R. van den

    1990-01-01

    The regulation of haemopoiesis occurs via complex interactions between the stroma and the haemopoietic cells. An attempt to further clarifying the mechanisms and the exact role of the stroma in the regulation was made in a study. Results revealed that the murine bone marrow stromal cells are highly radiosensitive after injection with 241-americium and can thus be considered as a target population after internal contamination. In addition, observations are made which may be important for risk estimation for the developing animal and during pregnancy. Contamination in utero and by lactation shows persistent damage up to 1 year after contamination at an average annual dose of 5 cGy. (author)

  2. Implications of plutonium and americium recycling on MOX fuel fabrication

    International Nuclear Information System (INIS)

    Renard, A.; Pilate, S.; Maldague, Th.; La Fuente, A.; Evrard, G.

    1995-01-01

    The impact of the multiple recycling of plutonium in power reactors on the radiation dose rates is analyzed for the most critical stage in a MOX fuel fabrication plant. The limitation of the number of Pu recycling in light water reactors would rather stem from reactor core physics features. The case of recovering americium with plutonium is also considered and the necessary additions of shielding are evaluated. A comparison between the recycling of Pu in fast reactors and in light water reactors is presented. (author)

  3. Recovery of americium-241 from aged plutonium metal

    International Nuclear Information System (INIS)

    Gray, L.W.; Burney, G.A.; Reilly, T.A.; Wilson, T.W.; McKibben, J.M.

    1980-01-01

    After separation and purification, both actinides were precipitated as oxalates and calcined. A large-scale process was developed using dissolution, separation, purification, precipitation, and calcination. Efforts were made to control corrosion, to avoid product contamination, to keep the volume of process and waste solutions manageable, and to denitrate solutions with formic acid. The Multipurpose Processing Facility (MPPF), designed for recovery of transplutonium isotopes, was used for the first time for the precipitation and calcination of americium. Also, for the first time,, large-scale formic acid denitration was performed in a canyon vessel at SRP

  4. Analysis of americium, plutonium and technetium solubility in groundwater

    International Nuclear Information System (INIS)

    Takeda, Seiji

    1999-08-01

    Safety assessments for geologic disposal of radioactive waste generally use solubilities of radioactive elements as the parameter restricting the dissolution of the elements from a waste matrix. This study evaluated americium, plutonium and technetium solubilities under a variety of geochemical conditions using the geochemical model EQ3/6. Thermodynamic data of elements used in the analysis were provided in the JAERI-data base. Chemical properties of both natural groundwater and interstitial water in buffer materials (bentonite and concrete) were investigated to determine the variations in Eh, pH and ligand concentrations (CO 3 2- , F - , PO 4 3- , SO 4 2- , NO 3 - and NH 4 + ). These properties can play an important role in the complexation of radioactive elements. Effect of the groundwater chemical properties on the solubility and formation of chemical species for americium, plutonium and technetium was predicted based on the solubility analyses under a variety of geochemical conditions. The solubility and speciation of the radioactive elements were estimated, taking into account the possible range of chemical compositions determined from the groundwater investigation. (author)

  5. Lifetime followup of the 1976 americium accident victim: [Final report

    International Nuclear Information System (INIS)

    Breitenstein, B.D. Jr.; Palmer, H.E.

    1988-05-01

    This report describes the 11 year medical course of Harold R. McCluskey, a Hanford nuclear chemical operator, who, at age 64, was involved in an accident in an americium recovery facility in August 1976. As a result of the accident, he was heavily contaminated with americium (Am-241), sustained a substantial internal deposition of this isotope, and was burned with concentrated nitric acid and injured by flying debris about the face and neck. The immediate and long-term medical care is summarized, including decontamination procedures, chelation therapy, and routine and special clinical laboratories studies. The estimates of the operator's Am-241 deposition, post accident and during the remainder of his life and the special techniques and equipment used to make the estimates, are reported. Post-accident, the total amount of Am-241 excreted in his urine and feces was 41 MBq (1.1 mCi). He died of complications of chronic coronary artery disease on August 17, 1987. 20 refs., 2 figs

  6. Americium-curium separation by means of selective extraction of hexavalent americium using a centrifugal contactor

    International Nuclear Information System (INIS)

    Musikas, C.; Germain, M.; Bathellier, A.

    1979-01-01

    This paper deals with Am (VI) - Cm (III) separation in nitrate media. The kinetics of oxidation of Am (III) by sodium persulfate in the presence of Ag + ions were reinvestigated by studying the effect of additions of small amounts of reagents which do not drastically change the distribution coefficients of Am (VI) or Cm (III) ions. Organo phosphorus solvents were selected because they are radiation resistant, possess weak reductant properties and that their affinity for hexavalent ion is high. The operating procedure was selected by consideration of the results of the two previous investigations. This can be done by using a centrifugal contactor enabling in to set organic-aqueous phase contact time in accordance with the kinetics of extraction of Am (VI), oxidation of Am (III) in aqueous phase, and reduction of Am (VI) in organic phase

  7. Solubility of Plutonium (IV) Oxalate During Americium/Curium Pretreatment

    International Nuclear Information System (INIS)

    Rudisill, T.S.

    1999-01-01

    Approximately 15,000 L of solution containing isotopes of americium and curium (Am/Cm) will undergo stabilization by vitrification at the Savannah River Site (SRS). Prior to vitrification, an in-tank pretreatment will be used to remove metal impurities from the solution using an oxalate precipitation process. Material balance calculations for this process, based on solubility data in pure nitric acid, predict approximately 80 percent of the plutonium in the solution will be lost to waste. Due to the uncertainty associated with the plutonium losses during processing, solubility experiments were performed to measure the recovery of plutonium during pretreatment and a subsequent precipitation process to prepare a slurry feed for a batch melter. A good estimate of the plutonium content of the glass is required for planning the shipment of the vitrified Am/Cm product to Oak Ridge National Laboratory (ORNL).The plutonium solubility in the oxalate precipitation supernate during pretreatment was 10 mg/mL at 35 degrees C. In two subsequent washes with a 0.25M oxalic acid/0.5M nitric acid solution, the solubility dropped to less than 5 mg/mL. During the precipitation and washing steps, lanthanide fission products in the solution were mostly insoluble. Uranium, and alkali, alkaline earth, and transition metal impurities were soluble as expected. An elemental material balance for plutonium showed that greater than 94 percent of the plutonium was recovered in the dissolved precipitate. The recovery of the lanthanide elements was generally 94 percent or higher except for the more soluble lanthanum. The recovery of soluble metal impurities from the precipitate slurry ranged from 15 to 22 percent. Theoretically, 16 percent of the soluble oxalates should have been present in the dissolved slurry based on the dilution effects and volumes of supernate and wash solutions removed. A trace level material balance showed greater than 97 percent recovery of americium-241 (from the beta dec

  8. Rare earth elements during diagenesis of abyssal sediments: analogies with a transuranic element americium

    International Nuclear Information System (INIS)

    Boust, D.

    1987-03-01

    One of the possibilities for the storage of high-level radioactive wastes consists in burying them into abyssal sediments, the sediments being supposed to barrier out radionuclides migration. The objective of the work was to estimate the efficiency of sediment barrier with respect to americium. As there is no americium in abyssal sediments, an indirect approach was used: the behaviour of the rare earth elements, the best natural analogs of americium. They were analysed in a 15 m long core, from the Cap Verde abyssal plateau. The terrigenous phase derived from the African continent was modified by short-term processes (1-1000 years); the intermediate rare earth elements were dissolved. Mineral coatings, enriched in rare earth appeared. After burial, the evolution continued at a much slower rate (10 5 - 10 6 years). The rare elements of the mineral coatings derived from the dissolution of the terrigenous phase and from an additional source, deeper in the sediment column. The fluxes of rare earth elements from sediment to water column were estimated. In suboxic sediments, the dissolved particulate equilibrium was related to redox conditions. The short-term reactivity of americium was studied in laboratory experiments. Simple americium migration models showed that the sediments barrier was totally efficient with respect to americium. In the conditions, neptunium 237 a daughter product of americium 241 could induce fluxes of 10 16 atoms per year per ton of stored waste (10 -8 Ci y-1), during millions years, towards the water column [fr

  9. Modelling of curium and americium behaviour during separation with displacing complexing chromatography

    International Nuclear Information System (INIS)

    Chuveleva, Eh.A.; Kharitonov, O.V.; Firsova, L.A.

    1994-01-01

    Certain heavy rare earths, curium and americium were separated by the method of displacement complexing chromatography using DTPA solutions and solutions containing DTPA and citric acid as eluents. Separation factors of rare earths and curium (americium) were calculated. Imitators for curium and americium separation were suggested: thulium for curium elution using 0.025 mol/l DTPA, holmium-for curium elution using 0.025 mol/l DTPA in the presence of 0.025 mol/l citric acid; terbium can serve as the imitator in both cases. 5 refs., 5 figs

  10. Influence of organic components on plutonium and americium speciation in soils and soil solutions

    International Nuclear Information System (INIS)

    Sokolik, G.A.; Ovsyannikova, S.V.; Kimlenko, I.M.

    2003-01-01

    Group composition of humic substances of organic and mineral soils sampled in the 30-km zone of the Chernobyl accident was analyzed for studying influence of organic components on migration properties of plutonium and americium in soils and soil solutions by the method of gel-chromatography and chemical fractionation. It was ascertained that humus of organic soils binds plutonium and americium stronger than humus of mineral soils. Elevated mobility of americium compared to plutonium one stems from lower ability of the latter to from hard to solve organic and organomineral complexes, as well as from its ability to form anionic complexes in soil solutions [ru

  11. Analytical separation of americium and curium, using high performance liquid chromatography

    International Nuclear Information System (INIS)

    Billon, A.

    1978-01-01

    Americium and curium are separated on a column of cation exchange resin (Aminex) using hydroxyisobutyric acid (α HIBA) as eluent, at a temperature of 80 0 C. Americium and curium were detected in line using their α emission: the separation was performed in a shielded glove box whose setting-up is given. Finally, the time necessary for a separation is comprised between 30 min and 1 hr. The purity of separated fractions was assayed by mass-spectrometry. An application in the determination of isotopic composition of americium and curium in fuels is described

  12. Development and Testing of an Americium/Lanthanide Separation Flowsheet Using Sodium Bismuthate

    Energy Technology Data Exchange (ETDEWEB)

    Jack Law; Bruce Mincher; Troy Garn; Mitchell Greenhalgh; Nicholas Schmitt; Veronica Rutledge

    2014-04-01

    The separation of Am from the lanthanides and curium is a key step in proposed advanced fuel cycle scenarios. The partitioning and transmutation of Am is desirable to minimize the long-term heat load of material interred in a future high-level waste repository. A separation process amenable to process scale-up remains elusive. Given only subtle chemistry differences within and between the ions of the trivalent actinide and lanthanide series this separation is challenging ; however, higher oxidation states of americium can be prepared using sodium bismuthate and separated via solvent extraction using diamylamylphosphonate (DAAP) extraction. Among the other trivalent metals only Ce is also oxidized and extracted. Due to the long-term instability of Am(VI) , the loaded organic phase is readily selectively stripped to partition the actinide to a new acidic aqueous phase. Batch extraction distribution ratio measurements were used to design a flowsheet to accomplish this separation. Additionally, crossflow filtration was investigated as a method to filter the bismuthate solids from the feed solution prior to extraction. Results of the filtration studies, flowsheet development work and flowsheet performance testing using a centrifugal contactor are detailed.

  13. Americium/Curium Vitrification Pilot Tests - Part II

    International Nuclear Information System (INIS)

    Marra, J.E.; Baich, M.A.; Fellinger, A.P.; Hardy, B.J.; Herman, D.T.; Jones, T.M.; Miller, C.B.; Miller, D.H.; Snyder, T. K.; Stone, M.E.

    1998-05-01

    Isotopes of americium (Am) and curium (Cm) were produced in the past at the Savannah River Site (SRS) for research, medical, and radiological applications. These highly radioactive and valuable isotopes have been stored in an SRS reprocessing facility for a number of years. Vitrification of this solution will allow the material to be more safely stored until it is transported to the DOE Oak Ridge Reservation for use in research and medical applications. A previous paper described operation results from the Am-Cm Melter 2A pilot system, a full-scale non-radioactive pilot facility. This paper presents the results from continued testing in the Pilot Facility and also describes efforts taken to look at alternative vitrification process operations and flowsheets designed to address the problems observed during melter 2A pilot testing

  14. Elimination of americium-241 after a case of accidental inhalation

    International Nuclear Information System (INIS)

    Edvardsson, K.A.; Lindgren, L.

    1976-01-01

    In handling a 241 Am source one person received an internal contamination of about 140 nCi of americium oxide, which was deposited in the lung region. Elimination of the activity was followed for more than 3 months by external gamma counting and excreta analyses. During the first week after the inhalation about 80% of the total intake was eliminated with an effective half-life of less than 2 days. The remaining activity, deposited in the lung region, was eliminated with an effective half-life of about 17 days. About 15% of the activity eliminated from the lung region from the 10th to the 50th day was eliminated in the faeces. (author)

  15. Pretreatment of americium/curium solutions for vitrification

    International Nuclear Information System (INIS)

    Rudisill, T.S.

    1996-01-01

    Vitrification will be used to stabilize an americium/curium (Am/Cm) solution presently stored in F-Canyon for eventual transport to the heavy isotope programs at Oak Ridge National Laboratory. Prior to vitrification, an in-tank oxalate precipitation and a series of oxalic/nitric acid washes will be used to separate these elements and lanthanide fission products from the bulk of the uranium and metal impurities present in the solution. Pretreatment development experiments were performed to understand the behavior of the lanthanides and the metal impurities during the oxalate precipitation and properties of the precipitate slurry. The results of these experiments will be used to refine the target glass composition allowing optimization of the primary processing parameters and design of the solution transfer equipment

  16. The biokinetics and radiotoxicology of curium: A comparison with americium

    Energy Technology Data Exchange (ETDEWEB)

    Menetrier, F. [CEA, Fontenay-aux-Roses (France); Taylor, D.M. [School of Chemistry, Cardiff University, Cardiff CF10 3AT (United Kingdom)], E-mail: davtay@btinternet.com; Comte, A. [CEA, Fontenay-aux-Roses (France)

    2008-05-15

    The human and animal data on the biokinetics of {sup 242}Cm and {sup 244}Cm are reviewed and shown to be very similar to those for {sup 241}Am. Liver and skeleton are the main organs of deposition and the retention of curium in the skeleton is very prolonged in all the species examined. Retention of both curium and americium in the liver appears to be species-dependent, being relatively rapidly removed from the liver of rats, and probably humans, but being tenaciously retained in dogs and some other species. The radiotoxicity of curium is also reviewed and it is shown that, as with {sup 241}Am, lung and bone tumour induction are the major hazards from inhaled and systemically deposited {sup 244}Cm. The use of chelating agents for the treatment of accidental contamination of the human body with {sup 242,244}Cm is also discussed.

  17. Determination of the oxygen-metal-ratio of uranium-americium mixed oxides

    International Nuclear Information System (INIS)

    Bartscher, W.

    1982-01-01

    During the dissolution of uranium-americium mixed oxides in phosphoric acid under nitrogen tetravalent uranium is oxidized by tetravalent americium. The obtained hexavalent uranium is determined by constant potential coulometry. The coulombs measured are equivalent to the oxygen in excess of the minimum composition of UO 2 x AmO 1 . 5 . The total uranium content of the sample is determined in a subsequent coulometric titration. The oxygen-metal ratio of the sample can be calculated for a given uranium-americium ratio. An excess of uranium dioxide is necessary in order to suppress the oxidation of water by tetravalent americium. The standard deviation of the method is 0.0017 O/M units. (orig.) [de

  18. Calibration procedures for in vivo sodium iodide spectrometry of plutonium and americium in the human lung

    International Nuclear Information System (INIS)

    Umbarger, C.J.; Jett, J.H.

    1976-01-01

    This paper describes the calibration techniques and associated error analysis for the in vivo measurement by NaI spectrometry of heavy elements in the lung, specifically plutonium and americium. A very brief description of the instrumentation system is included

  19. Kinetics of americium(VI) mass transfer through solid supported liquid membrane with HDEHP

    International Nuclear Information System (INIS)

    Mikheeva, M.N.; Novicoov, P.; Myasoedov, B.F.; Tikhomirov, S.V.

    1994-01-01

    The main regularities of membrane extraction of americium under conditions of different redox potentials in aqueous phases have been studied. The physico-chemical model of the process including steps of americium oxidation in feed solution, extraction by membrane, partial reduction on membrane surface, trans-membrane diffusion and reextraction to strip solution has been developed. The calculation of reduction rate constant on membrane surface has been carried out. (author) 9 refs.; 4 figs.; 3 tabs

  20. In-line measurement of plutonium and americium in mixed solutions

    International Nuclear Information System (INIS)

    Li, T.K.

    1981-01-01

    A solution assay instrument (SAI) has been developed at the Los Alamos National Laboratory and installed in the plutonium purification and americium recovery process area in the Los Alamos Plutonium Processing Facility. The instrument is designed for accurate, timely, and simultaneous nondestructive analysis of plutonium and americium in process solutions that have a wide range of concentrations and Am/Pu ratios. For a 25-mL sample, the assay precision is 5 g/L within a 2000-s count time

  1. Radiation protection data sheets for the use of Americium 241 in unsealed sources

    International Nuclear Information System (INIS)

    Anon.

    1993-01-01

    This radiation protection data sheet is intended for supervisors and staff in the different medical, hospital, pharmaceutical, university and industrial laboratories and departments where Americium 241 is handled, and also for all those involved in risk prevention in this field. It provides essential data on radiation protection measures during the use of Americium 241 in unsealed sources: physical characteristics, risk assessment, administrative procedures, recommendations, regulations and bibliography

  2. The transmutation of americium: the Ecrix experiments in Phenix; Transmutation de l'americium: les experiences ecrix dans Phenix

    Energy Technology Data Exchange (ETDEWEB)

    Garnier, J.C.; Schmidt, N. [CEA Cadarache, Dept. d' Etudes des Combustibles (DEC/SESC), 13 - Saint-Paul-lez-Durance (France); Croixmarie, Y.; Ottaviani, J.P. [CEA Cadarache, Dept. d' Etudes des Combustibles (DEC/SPUA), 13 - Saint-Paul-lez-Durance (France); Varaine, F.; Saint Jean, C. de [CEA Cadarache, Dept. d' Etudes des Reacteurs (DER/SPRC), 13 - Saint-Paul-lez-Durance (France)

    1999-07-01

    The first americium transmutation experiment in a specific target in PHENIX will occur with the ECRIX-B and ECRIX-H experiments. Beside material testing, the objective is also to represent a concept of transmutation whose specificity is to enhance the kinetics of transmutation by using a moderated spectrum. The moderator materials will be {sup 11}B{sub 4}C and CaH{sub 2} for ECRIX-B and ECRIXH respectively, the irradiation conditions have been predicted for both the neutronics and thermal. The targets (MgO-AmO{sub X} pellets) are manufactured in the ATALANTE laboratory and the design is performed according to the PHENIX operating conditions. (authors)

  3. The transmutation of americium: the Ecrix experiments in Phenix; Transmutation de l'americium: les experiences ecrix dans Phenix

    Energy Technology Data Exchange (ETDEWEB)

    Garnier, J C; Schmidt, N [CEA Cadarache, Dept. d' Etudes des Combustibles (DEC/SESC), 13 - Saint-Paul-lez-Durance (France); Croixmarie, Y; Ottaviani, J P [CEA Cadarache, Dept. d' Etudes des Combustibles (DEC/SPUA), 13 - Saint-Paul-lez-Durance (France); Varaine, F; Saint Jean, C de [CEA Cadarache, Dept. d' Etudes des Reacteurs (DER/SPRC), 13 - Saint-Paul-lez-Durance (France)

    1999-07-01

    The first americium transmutation experiment in a specific target in PHENIX will occur with the ECRIX-B and ECRIX-H experiments. Beside material testing, the objective is also to represent a concept of transmutation whose specificity is to enhance the kinetics of transmutation by using a moderated spectrum. The moderator materials will be {sup 11}B{sub 4}C and CaH{sub 2} for ECRIX-B and ECRIXH respectively, the irradiation conditions have been predicted for both the neutronics and thermal. The targets (MgO-AmO{sub X} pellets) are manufactured in the ATALANTE laboratory and the design is performed according to the PHENIX operating conditions. (authors)

  4. Biochemical fractionation and cellular distribution of americium and plutonium in the biomass of freshwater macrophytes

    International Nuclear Information System (INIS)

    Zotina, T.A.; Kalacheva, G.S.; Bolsunovsky, A.Ya.

    2011-01-01

    Accumulation of americium ( 241 Am) and plutonium ( 238,242 Pu) and their distribution in cell compartments and biochemical components of the biomass of freshwater aquatic plants Elodea canadensis, Ceratophyllum demersum and Myrioplyllum spicatum and aquatic moss Fontinalis antipyretica have been investigated in laboratory experiments. Americium and plutonium taken up from water by Elodea canadensis apical shoots were mainly absorbed by structural components of plant cells (90% for 241 Am; 89% for 238 Pu and 82-87% for 242 Pu). About 10-18% of isotope activity was recorded in the cytosol fraction. The major concentration (76-92%) of americium was bound to cell wall cellulose-like polysaccharides of Elodea canadensis, Myriophyllum spicatum, Ceratophyllum demersum and Fontinalis antipyretica, 8-24% of americium activity was registered in the fraction of proteins and carbohydrates, and just a minor concentration (<1%) in the lipid fraction. The distribution of plutonium in the biomass fractions of Elodea was similar to that of americium. Hence, americium and plutonium had the highest affinity to cellulose-like polysaccharides of cell walls of freshwater submerged macrophytes. (author)

  5. Distribution of uranium, americium and plutonium in the biomass of freshwater macrophytes

    International Nuclear Information System (INIS)

    Zotina, T.A.; Kalacheva, G.S.; Bolsunovsky, A.YA.

    2010-01-01

    Accumulation of uranium ( 238 U), americium ( 241 Am) and plutonium ( 242 Pu) and their distribution in cell compartments and biochemical components of the biomass of aquatic plants Elodea canadensis, Ceratophyllum demersum, Myrioplyllum spicatum and aquatic moss Fontinalis antipyretica have been investigated in laboratory batch experiments. Isotopes of uranium, americium and plutonium taken up from the water by Elodea canadensis apical shoots were mainly absorbed by cell walls, plasmalemma and organelles. A small portion of isotopes (about 6-13 %) could be dissolved in cytoplasm. The major portion (76-92 %) of americium was bound to cell wall cellulose-like polysaccharides of Elodea canadensis, Myriophyllum spicatum, Ceratophyllum demersum and Fontinalis antipyretica, 8-23 % of americium activity was registered in the fraction of proteins and carbohydrates, and just a small portion (< 1%) in lipid fraction. The distribution of plutonium in the biomass fraction of Elodea was similar to that of americium. Hence, americium and plutonium had the highest affinity to cellulose-like polysaccharides in Elodea biomass. Distribution of uranium in the biomass of Elodea differed essentially from that of transuranium elements: a considerable portion of uranium was recorded in the fraction of protein and carbohydrates (51 %). From our data we can assume that uranium has higher affinity to carbohydrates than proteins. (authors)

  6. Distribution of uranium, americium and plutonium in the biomass of freshwater macrophytes

    Energy Technology Data Exchange (ETDEWEB)

    Zotina, T.A.; Kalacheva, G.S.; Bolsunovsky, A.YA. [Institute of Biophysics SB RAS, Akademgorodok, Krasnoyarsk (Russian Federation)

    2010-07-01

    Accumulation of uranium ({sup 238}U), americium ({sup 241}Am) and plutonium ({sup 242}Pu) and their distribution in cell compartments and biochemical components of the biomass of aquatic plants Elodea canadensis, Ceratophyllum demersum, Myrioplyllum spicatum and aquatic moss Fontinalis antipyretica have been investigated in laboratory batch experiments. Isotopes of uranium, americium and plutonium taken up from the water by Elodea canadensis apical shoots were mainly absorbed by cell walls, plasmalemma and organelles. A small portion of isotopes (about 6-13 %) could be dissolved in cytoplasm. The major portion (76-92 %) of americium was bound to cell wall cellulose-like polysaccharides of Elodea canadensis, Myriophyllum spicatum, Ceratophyllum demersum and Fontinalis antipyretica, 8-23 % of americium activity was registered in the fraction of proteins and carbohydrates, and just a small portion (< 1%) in lipid fraction. The distribution of plutonium in the biomass fraction of Elodea was similar to that of americium. Hence, americium and plutonium had the highest affinity to cellulose-like polysaccharides in Elodea biomass. Distribution of uranium in the biomass of Elodea differed essentially from that of transuranium elements: a considerable portion of uranium was recorded in the fraction of protein and carbohydrates (51 %). From our data we can assume that uranium has higher affinity to carbohydrates than proteins. (authors)

  7. Effect of americium-241 on luminous bacteria. Role of peroxides

    Energy Technology Data Exchange (ETDEWEB)

    Alexandrova, M., E-mail: maka-alexandrova@rambler.r [Siberian Federal University, Svobodny 79, 660041 Krasnoyarsk (Russian Federation); Rozhko, T. [Siberian Federal University, Svobodny 79, 660041 Krasnoyarsk (Russian Federation); Vydryakova, G. [Institute of Biophysics SB RAS, Akademgorodok 50, 660036 Krasnoyarsk (Russian Federation); Kudryasheva, N. [Siberian Federal University, Svobodny 79, 660041 Krasnoyarsk (Russian Federation); Institute of Biophysics SB RAS, Akademgorodok 50, 660036 Krasnoyarsk (Russian Federation)

    2011-04-15

    The effect of americium-241 ({sup 241}Am), an alpha-emitting radionuclide of high specific activity, on luminous bacteria Photobacterium phosphoreum was studied. Traces of {sup 241}Am in nutrient media (0.16-6.67 kBq/L) suppressed the growth of bacteria, but enhanced luminescence intensity and quantum yield at room temperature. Lower temperature (4 {sup o}C) increased the time of bacterial luminescence and revealed a stage of bioluminescence inhibition after 150 h of bioluminescence registration start. The role of conditions of exposure the bacterial cells to the {sup 241}Am is discussed. The effect of {sup 241}Am on luminous bacteria was attributed to peroxide compounds generated in water solutions as secondary products of radioactive decay. Increase of peroxide concentration in {sup 241}Am solutions was demonstrated; and the similarity of {sup 241}Am and hydrogen peroxide effects on bacterial luminescence was revealed. The study provides a scientific basis for elaboration of bioluminescence-based assay to monitor radiotoxicity of alpha-emitting radionuclides in aquatic solutions. - Highlights: {yields} Am-241 in water solutions (A = 0.16-6.7 kBq/L) suppresses bacterial growth.{yields} Am-241 (A = 0.16-6.7 kBq/L) stimulate bacterial luminescence. {yields} Peroxides, secondary radiolysis products, cause increase of bacterial luminescence.

  8. Density of simulated americium/curium melter feed solution

    International Nuclear Information System (INIS)

    Rudisill, T.S.

    1997-01-01

    Vitrification will be used to stabilize an americium/curium (Am/Cm) solution presently stored in F-Canyon for eventual transport to Oak Ridge National Laboratory and use in heavy isotope production programs. Prior to vitrification, a series of in-tank oxalate precipitation and nitric/oxalic acid washes will be used to separate these elements and lanthanide fission products from the bulk of the uranium and metal impurities present in the solution. Following nitric acid dissolution and oxalate destruction, the solution will be denitrated and evaporated to a dissolved solids concentration of approximately 100 g/l (on an oxide basis). During the Am/Cm vitrification, an airlift will be used to supply the concentrated feed solution to a constant head tank which drains through a filter and an in-line orifice to the melter. Since the delivery system is sensitive to the physical properties of the feed, a simulated solution was prepared and used to measure the density as a function of temperature between 20 to 70 degrees C. The measured density decreased linearly at a rate of 0.0007 g/cm3/degree C from an average value of 1.2326 g/cm 3 at 20 degrees C to an average value of 1.1973g/cm 3 at 70 degrees C

  9. Americium/Curium Melter 2A Pilot Tests

    International Nuclear Information System (INIS)

    Smith, M.E.; Fellinger, A.P.; Jones, T.M.; Miller, C.B.; Miller, D.H.; Snyder, T.K.; Stone, M.E.; Witt, D.C.

    1998-05-01

    Isotopes of americium (Am) and curium (Cm) were produced in the past at the Savannah River Site (SRS) for research, medical, and radiological applications. These highly radioactive and valuable isotopes have been stored in an SRS reprocessing facility for a number of years. Vitrification of this solution will allow the material to be more safely stored until it is transported to the DOE Oak Ridge Reservation for use in research and medical applications. To this end, the Am/Cm Melter 2A pilot system, a full-scale non- radioactive pilot plant of the system to be installed at the reprocessing facility, was designed, constructed and tested. The full- scale pilot system has a frit and aqueous feed delivery system, a dual zone bushing melter, and an off-gas treatment system. The main items which were tested included the dual zone bushing melter, the drain tube with dual heating and cooling zones, glass compositions, and the off-gas system which used for the first time a film cooler/lower melter plenum. Most of the process and equipment were proven to function properly, but several problems were found which will need further work. A system description and a discussion of test results will be given

  10. Americium adsorption on the surface of macrophytic algae

    Energy Technology Data Exchange (ETDEWEB)

    Carvalho, F.P.; Fowler, S.W.

    1985-01-01

    Data are presented on the rates at which americium (Am) deposits upon blade surfaces of three benthic algal species (Ulva rigida, Fucus vesiculosus and Gigartina stellata) following short-term exposures (1-6 h). Am is taken up in direct proportion to the ambient radionuclide concentration in sea water. Uptake by the green alga was 3 to 5 times greater than that for the brown and red species. Experimental evidence indicated that Am accumulation is a passive process and that adsorption takes place mainly on the thin outer organic coating of the seaweed. The Am transport coefficients are quite similar to that previously found for the naturally occurring ..cap alpha..-emitter /sup 210/Po, but are an order of magnitude lower than a plutonium transport coefficient reported in the literature. Release of labelled extracellular products associated with the algal surface coating is considered to be responsible for the rapid loss of Am observed previously in macroalgae and may in fact serve as a mechanism for transferring Am to filter feeding zooplankton. (author).

  11. Americium adsorption on the surface of macrophytic algae

    International Nuclear Information System (INIS)

    Carvalho, F.P.; Fowler, S.W.

    1985-01-01

    Data are presented on the rates at which americium (Am) deposits upon blade surfaces of three benthic algal species (Ulva rigida, Fucus vesiculosus and Gigartina stellata) following short-term exposures (1-6 h). Am is taken up in direct proportion to the ambient radionuclide concentration in sea water. Uptake by the green alga was 3 to 5 times greater than that for the brown and red species. Experimental evidence indicated that Am accumulation is a passive process and that adsorption takes place mainly on the thin outer organic coating of the seaweed. The Am transport coefficients are quite similar to that previously found for the naturally occurring α-emitter 210 Po, but are an order of magnitude lower than a plutonium transport coefficient reported in the literature. Release of labelled extracellular products associated with the algal surface coating is considered to be responsible for the rapid loss of Am observed previously in macroalgae and may in fact serve as a mechanism for transferring Am to filter feeding zooplankton. (author)

  12. Density of simulated americium/curium melter feed solution

    Energy Technology Data Exchange (ETDEWEB)

    Rudisill, T.S.

    1997-09-22

    Vitrification will be used to stabilize an americium/curium (Am/Cm) solution presently stored in F-Canyon for eventual transport to Oak Ridge National Laboratory and use in heavy isotope production programs. Prior to vitrification, a series of in-tank oxalate precipitation and nitric/oxalic acid washes will be used to separate these elements and lanthanide fission products from the bulk of the uranium and metal impurities present in the solution. Following nitric acid dissolution and oxalate destruction, the solution will be denitrated and evaporated to a dissolved solids concentration of approximately 100 g/l (on an oxide basis). During the Am/Cm vitrification, an airlift will be used to supply the concentrated feed solution to a constant head tank which drains through a filter and an in-line orifice to the melter. Since the delivery system is sensitive to the physical properties of the feed, a simulated solution was prepared and used to measure the density as a function of temperature between 20 to 70{degrees} C. The measured density decreased linearly at a rate of 0.0007 g/cm3/{degree} C from an average value of 1.2326 g/cm{sup 3} at 20{degrees} C to an average value of 1.1973g/cm{sup 3} at 70{degrees} C.

  13. Molecular localisation of americium, technetium and cesium in edible marine animals. Their metabolic behavior and their consequences; Localisation moleculaire de l'americium, du technetium et du cesium chez des animaux marins comestibles leur comportement metabolique et ses consequences

    Energy Technology Data Exchange (ETDEWEB)

    Pieri, J; Goudard, F; Milcent, M C [Laboratoire de Biochimie et Radiochimie, Faculte des Sciences et des Techniques, Nantes Cedex (France)

    1992-07-01

    We show the molecular behavior of americium, technetium and cesium on the chromatographic pattern of each cytosol in the digestive gland of eel and lobster. The contamination by cadmium seems to compete with americium in the fractions of MW 10,000. Cesium shows an ionic behavior. (author)

  14. Environmental impact of a teratogenic actinide: a case study of americium-241

    Energy Technology Data Exchange (ETDEWEB)

    Wang, J.; Yang, J.Y.

    1985-10-16

    Americium-241 is widely used as a radiation source, but it also has some potential risk if taken into the body. Although the radiotoxicity of americium-241 is small compared to other transuranic actinides, its effects on the reproductive system and on development of the placenta are more damaging than the effects of plutonium-239. A previous report based on a worst-case scenario involving a hypothetical fire accident in a contaminated facility indicated that there could have been a significant impact on nearby residents from a unit release of americium-241 via atmospheric dispersion. However, because the facility is located in a rural region where most drinking water supplies are drawn from private wells, it is believed that deposition of americium-241 from the atmosphere might also have impacts via the groundwater pathway by infiltration of rainwater. In this analysis, a three-dimensional analytical mathematical model is used to assess several aspects of americium-241 contamination of groundwater, including radioactive transformation, advection, dispersion, and soil sorption. Simulation results indicate that no significant radiological impacts would occur to the nearby residents via the groundwater pathway. 15 refs., 2 figs., 2 tabs.

  15. The availability of plutonium and americium in Irish Sea sediments for re-dissolution

    International Nuclear Information System (INIS)

    McDonald, P.; Vives i Batlle, J.; Bousher, A.; Whittall, A.; Chambers, N.

    2001-01-01

    The availability of plutonium and americium, for re-dissolution from offshore sediments into Irish Sea water, has been examined. Sediments collected from the mud-patch near the Cumbrian coast were characterized in terms of spatial location, particle size, partitioning of radionuclides with respect to physico-chemical bonds and availability of actinides for release into seawater. Sequential extraction investigations revealed that plutonium was predominantly associated with strongly bound sesquioxide and organic complex fractions. Americium was associated mainly with the organic complex fraction, but a significant fraction was in carbonate form. Sediment/water re-dissolution experiments with and without stirring were compared to simulate the effect of disturbing bed sediment. After 1 week, neither set of re-dissolution data provided significant trends between dissolved activity and time. Stirred systems appeared to release 2.5 times more plutonium and americium into seawater than unstirred systems. Measured 239,240Pu and 241Am distribution coefficients (K d values) were both typically approximately 10 5 l kg -1 . 241Am K d values are an order of magnitude lower than previously reported for the north-eastern Irish Sea, but similar to western Irish Sea values. Overall, the fractions of plutonium and americium available for re-dissolution from bed sediment are very low at <0.1%, with proportionally more plutonium being released than americium. These findings lend further support for the extrapolation of laboratory-derived information to environmental conditions

  16. Environmental impact of a teratogenic actinide: a case study of americium-241

    International Nuclear Information System (INIS)

    Wang, J.; Yang, J.Y.

    1985-01-01

    Americium-241 is widely used as a radiation source, but it also has some potential risk if taken into the body. Although the radiotoxicity of americium-241 is small compared to other transuranic actinides, its effects on the reproductive system and on development of the placenta are more damaging than the effects of plutonium-239. A previous report based on a worst-case scenario involving a hypothetical fire accident in a contaminated facility indicated that there could have been a significant impact on nearby residents from a unit release of americium-241 via atmospheric dispersion. However, because the facility is located in a rural region where most drinking water supplies are drawn from private wells, it is believed that deposition of americium-241 from the atmosphere might also have impacts via the groundwater pathway by infiltration of rainwater. In this analysis, a three-dimensional analytical mathematical model is used to assess several aspects of americium-241 contamination of groundwater, including radioactive transformation, advection, dispersion, and soil sorption. Simulation results indicate that no significant radiological impacts would occur to the nearby residents via the groundwater pathway. 15 refs., 2 figs., 2 tabs

  17. Mobility of plutonium and americium through a shallow aquifer in a semiarid region

    International Nuclear Information System (INIS)

    Penrose, W.R.; Polzer, W.L.; Essington, E.H.; Nelson, D.M.; Orlandini, K.A.

    1990-01-01

    Treated liquid wastes containing traces of plutonium and americium are released into Mortandad Canyon, within the site of Los Alamos National Laboratory, NM. The wastes infiltrate a small aquifer within the canyon. Although laboratory studies have predicted that the movement of actinides in subsurface environments will be limited to less than a few meters, both plutonium and americium are detectable in monitoring wells as far as 3,390 m downgradient from the discharge. Between the first and last monitoring wells (1.8 and 3.4 km from the discharge), plutonium concentrations decreased exponentially from 1,400 to 0.55 mBq/L. Americium concentrations ranged between 94 and 1,240 mBq/L, but did not appear to vary in a systematic way with distance. Investigation of the properties of the mobile actinides indicates that the plutonium and part of the americium are tightly or irreversibly associated with colloidal material between 25 and 450 nm in size. The colloidally bound actinides are removed only gradually from the groundwater. The fraction of the americium not associated with colloids exists in a low molecular weight form (diameter, ≤ 2 nm) and appears to be a stable, anionic complex of unknown composition. The mobile forms of these actinides defeat the forces that normally act to retard their movement through groundwater systems

  18. Transport of plutonium, americium, and curium from soils into plants by roots

    International Nuclear Information System (INIS)

    Pimpl, M.; Schuettelkopf, H.

    1979-12-01

    For assessing the dose from radionuclides in agricultural products by ingestion it is necessary to know the soil to plant transfer factors. The literature was entirely investigated, in order to judge the size of the soil to plant transfer factors. In total, 92 publications - from 1948 to 1978 -have been evaluated. As result, transfer factors from 10 -9 to 10 -3 have been found for Plutonium, and from 10 -6 to 1 for Americium. For Curium only few data are available in literature. The considerable variation of the measured transfer factors is based on the dependence of these transfer factors from the ion exchange capacity of soils, from the amount of organic materials, from the pH-value, and from the mode of contamination. There are, in any case, contradictory data, although there has been detected a dependence of the transfer factors from these parameters. Chelating agenst increase the transfer factors to approximately 1300. As well, fertilizers have an influence on the size of the transfer factors - however, the relationships have been scarcely investigated. The distribution of actinides within the individual parts of plants has been investigated. The highest concentrations are in the roots; in the plant parts above ground the concentration of actinides decreases considerably. The most inferior transfer factors were measured for the respective seed or fruits. The soil to plant transfer factors of actinides are more dependend on the age of the plants within one growing period. At the beginning of the period, the transfer factor is considerably higher than at the end of this period. With respect to plants with a growing period of several years, correlations are unknown. (orig.) [de

  19. A review on the mass spectrometric studies of americium: Present status and future perspective.

    Science.gov (United States)

    Aggarwal, Suresh Kumar

    2018-01-01

    The manuscript reviews the various mass spectrometric techniques for analysis and chemical studies of Americium. These methods include thermal ionization mass spectrometry (TIMS), and inductively coupled plasma source mass spectrometry (ICPMS) for the determination of Am isotope ratios and concentration in nuclear fuel samples of interest in nuclear technology, and in complex biological and environmental samples. Ultra-sensitive mass spectrometric techniques of resonance-ionization mass spectrometry (RIMS), and accelerator-based mass spectrometry (AMS) are also discussed. The novel applications of electrospray ionization mass spectrometry (ESIMS) to understand the solution chemistry of Am and other actinides are presented. These studies are important in view of the world-wide efforts to develop novel complexing agents to separate lanthanides and minor actinides (Am, Np, and Cm) for partitioning and transmutation of minor actinides from the point of view of nuclear waste management. These mass spectrometry experiments are also of great interest to examine the covalent character of actinides with increasing atomic number. Studies on gas-phase chemistry of Am and its oxides with Knudsen effusion mass spectrometry (KEMS), Fourier-transform ion cyclotron resonance mass spectrometry (FTICR-MS), and laser-based experiments with reflectron time-of-flight mass spectrometer (R-ToF) are highlighted. These studies are important to understand the fundamental chemistry of 5f electrons in actinides. Requirement of certified isotopic reference materials of Am to improve the accuracy of experimental nuclear data (e.g., the half-life of 243 Am) is emphasized. © 2016 Wiley Periodicals, Inc. Mass Spec Rev. © 2016 Wiley Periodicals, Inc.

  20. Molecular localisation of americium, technetium and cesium in edible marine animals. Their metabolic behavior and their consequences

    International Nuclear Information System (INIS)

    Pieri, J.; Goudard, F.; Milcent, M.C.

    1992-01-01

    We show the molecular behavior of americium, technetium and cesium on the chromatographic pattern of each cytosol in the digestive gland of eel and lobster. The contamination by cadmium seems to compete with americium in the fractions of MW 10,000. Cesium shows an ionic behavior. (author)

  1. Organic components and plutonium and americium state in soils and soil solutions

    International Nuclear Information System (INIS)

    Sokolik, G.A.; Ovsyannikova, S.V.; Kimlenko, I.M.

    2002-01-01

    The fraction composition of humus substances of different type soils and soil solutions have been studied. A distribution of Pu 239, 240 and Am 241 between humus substances fractions of different dispersity and mobility in soil-vegetation cover has been established. It was shown that humus of organic soils fixes plutonium and americium in soil medium in greater extent than humus of mineral soils. That leads to lower migration ability of radionuclides in organic soils. The lower ability of americium to form difficultly soluble organic and organic-mineral complexes and predomination of its anion complexes in soil solutions may be a reason of higher mobility and biological availability of americium in comparison to plutonium during soil-plant transfer (authors)

  2. Transmutation of Americium in Light and Heavy Water Reactors

    Energy Technology Data Exchange (ETDEWEB)

    Hyland, B.; Dyck, G.R.; Edwards, G.W.R. [Chalk River Laboratories, Atomic Energy of Canada Limited (Canada); Ellis, R.J.; Gehin, J.C. [Oak Ridge National Laboratory (ORNL), Oak Ridge, Tennessee (United States); Maldonado, G.I. [University of Tennessee (Knoxville)/ORNL, Tennessee (United States)

    2009-06-15

    There is interest worldwide in reducing the burden on geological nuclear fuel disposal sites. In most disposal scenarios the decay heat loading of the surrounding rock limits the capacity of these sites. On the long term, this decay heat is generated primarily by actinides, and a major contributor 100 to 1000 years after discharge from the reactor is {sup 241}Am. One possible approach to reducing the decay-heat burden is to reprocess spent reactor fuel and use thermal spectrum reactors to 'burn' the Am nuclides. The viability of this approach is dependent upon the detailed changes in chemical and isotopic composition of actinide-bearing fuels after irradiation in thermal reactor spectra. The currently available thermal spectrum reactor options include light water-reactors (LWRs) and heavy-water reactors (HWRs) such as the CANDU{sup R} designs. In addition, as a result of the recycle of spent LWR fuel, there would be a considerable amount of potential recycled uranium (RU). One proposed solution for the recycled uranium is to use it as fuel in Candu reactors. This paper investigates the possibilities of transmuting americium in 'spiked' bundles in pressurized water reactors (PWRs) and in boiling water reactors (BWRs). Transmutation of Am in Candu reactors is also examined. One scenario studies a full core fuelled with homogeneous bundles of Am mixed with recycled uranium, while a second scenario places Am in an inert matrix in target channels in a Candu reactor, with the rest of the reactor fuelled with RU. A comparison of the transmutation in LWRs and HWRs is made, in terms of the fraction of Am that is transmuted and the impact on the decay heat of the spent nuclear fuel. CANDU{sup R} is a registered trademark of Atomic Energy of Canada Limited (AECL). (authors)

  3. The rapid determination of americium curium, and uranium in urine by ultrafiltration

    International Nuclear Information System (INIS)

    Stradling, G.N.; Popplewell, D.S.; Ham, G.J.; Griffin, R.

    1975-01-01

    The rapid ultrafiltration method developed for the assay of plutonium has been extended to the determination of americium, curium and uranium in urine. The limits of detection for americium and curium, and uranium are 0.09 and 0.12 dm -1 l -1 respectively, and the analysis time excluding counting less than 2 hours. The method can therefor be effectively used as a rapid screening procedure. When the reference level for plutonium is exceeded, the α activity may require to be characterised. The single ultrafiltration technique must be modified for turbid urine samples. The method is inappropriate, except for uranium, when the urine contains DTPA. (author)

  4. Carbamoyl methylphosphine oxide derivatives of adamantane as americium and europium extractants

    International Nuclear Information System (INIS)

    Babain, V.A.; Alyapyshev, M.Yu.; Novakov, I.A.; Orlinson, B.S.; Savel'ev, E.N.; Shokova, Eh.A.; Serebrayannikova, A.E.; Kovalev, V.V.

    2007-01-01

    Adamantane di-1,3-carbamoyl methylphosphine oxide (CMPO) derivatives, where CMPO-groups connect with 1,3-positions of rigid adamantane platform by methylene and ethylene bridges, are synthesized, and their efficiency as extractants of americium(III) and europium(III) from nitric acid solutions is demonstrated. Distribution function of Am 3+ and Eu + during extraction from 3M HNO 3 are measured in the investigation of extraction properties. It is noted that first synthesized adamantane CMPO derivatives are more effective for the extraction of americium(III) and europium(III) from 3MHNO 3 [ru

  5. Airborne plutonium and americium concentrations measured from the top of Rattlesnake Mountain

    International Nuclear Information System (INIS)

    Sehmel, G.A.

    1979-01-01

    Airborne plutonium-239+240 and americium-241 blowing from offsite was measured in an initial experiment at the top of Rattlesnake Mountain. Average airborne concentration measured was similar to fallout concentrations. Airborne plutonium concentrations were independent of wind speed for seven wind speed increments between 0.5 and 31 m/sec. In contrast the airborne americium concentration was a minimum at a wind speed of approximately 7 m/sec. Similarly, the airborne solids concentration in μg/m 3 was a minimum at an intermediate wind speed increment of 7 to 11 m/sec

  6. Evaluation of synthetic water-soluble metal-binding polymers with ultrafiltration for selective concentration of americium and plutonium

    International Nuclear Information System (INIS)

    Smith, B.F.; Gibson, R.R.; Jarvinen, G.D.; Jones, M.M.; Lu, M.T.; Robison, T.W.; Schroeder, N.C.; Stalnaker, N.

    1997-01-01

    Routine counting methods and ICP-MS are unable to directly measure the new US Department of Energy (DOE) regulatory level for discharge waters containing alpha-emitting radionuclides of 30 pCi/L total alpha or the 0.05 pCi/L regulatory level for Pu or Am activity required for surface waters at the Rocky Flats site by the State of Colorado. This inability indicates the need to develop rapid, reliable, and robust analytical techniques for measuring actinide metal ions, particularly americium and plutonium. Selective separation or preconcentration techniques would aid in this effort. Water-soluble metal-binding polymers in combination with ultrafiltration are shown to be an effective method for selectively removing dilute actinide ions from acidic solutions of high ionic strength. The actinide-binding properties of commercially available water-soluble polymers and several polymers which have been reported in the literature were evaluated. The functional groups incorporated in the polymers were pyrrolidone, amine, oxime, and carboxylic, phosphonic, or sulfonic acid. The polymer containing phosphonic acid groups gave the best results with high distribution coefficients and concentration factors for 241 Am(III) and 238 Pu(III)/(IV) at pH 4 to 6 and ionic strengths of 0.1 to 4

  7. Use of radioanalytical methods for determination of uranium, neptunium, plutonium, americium and curium isotopes in radioactive wastes

    International Nuclear Information System (INIS)

    Geraldo, Bianca

    2012-01-01

    Activated charcoal is a common type of radioactive waste that contains high concentrations of fission and activation products. The management of this waste includes its characterization aiming the determination and quantification of the specific radionuclides including those known as Difficult-to-Measure Radionuclides (RDM). The analysis of the RDM's generally involves complex radiochemical analysis for purification and separation of the radionuclides, which are expensive and time-consuming. The objective of this work was to define a methodology for sequential analysis of the isotopes of uranium, neptunium, plutonium, americium and curium present in a type of radioactive waste, evaluating chemical yield, analysis of time spent, amount of secondary waste generated and cost. Three methodologies were compared and validated that employ ion exchange (TI + EC), extraction chromatography (EC) and extraction with polymers (ECP). The waste chosen was the activated charcoal from the purification system of primary circuit water cooling the reactor IEA-R1. The charcoal samples were dissolved by acid digestion followed by purification and separation of isotopes with ion exchange resins, extraction and chromatographic extraction polymers. Isotopes were analyzed on an alpha spectrometer, equipped with surface barrier detectors. The chemical yields were satisfactory for the methods TI + EC and EC. ECP method was comparable with those methods only for uranium. Statistical analysis as well the analysis of time spent, amount of secondary waste generated and cost revealed that EC method is the most effective for identifying and quantifying U, Np, Pu, Am and Cm present in charcoal. (author)

  8. On-line separation of Pu(III) and Am(III) using extraction and ion chromatography

    International Nuclear Information System (INIS)

    Jernstroem, J.; Lehto, J.; Betti, M.

    2007-01-01

    An on-line method developed for separating plutonium and americium was developed. The method is based on the use of HPLC pump with three analytical chromatographic columns. Plutonium is reduced throughout the procedure to trivalent oxidation state, and is recovered in the various separation steps together with americium. Light lanthanides and trivalent actinides are separated with TEVA resin in thiocyanate/formic acid media. Trivalent plutonium and americium are pre-concentrated in a TCC-II cation-exchange column, after which the separation is performed in CS5A ion chromatography column by using two different eluents. Pu(III) is eluted with a dipicolinic acid eluent, and Am(III) with oxalic acid eluent. Radiochemical and chemical purity of the eluted plutonium and americium fractions were ensured with alpha-spectrometry. (author)

  9. Experimental studies to validate model calculations and maximum solubility limits for Plutonium and Americium; Experimentelle Arbeiten zur Absicherung von Modellrechnungen und Maximalkonzentrationen fuer Plutonium und Americium

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2017-02-16

    This report focuses on studies of KIT-INE to derive a significantly improved description of the chemical behaviour of Americium and Plutonium in saline NaCl, MgCl{sub 2} and CaCl{sub 2} brine systems. The studies are based on new experimental data and aim at deriving reliable Am and Pu solubility limits for the investigated systems as well as deriving comprehensive thermodynamic model descriptions. Both aspects are of high relevance in the context of potential source term estimations for Americium and Plutonium in aqueous brine systems and related scenarios. Americium and Plutonium are long-lived alpha emitting radionuclides which due to their high radiotoxicity need to be accounted for in a reliable and traceable way. The hydrolysis of trivalent actinides and the effect of highly alkaline pH conditions on the solubility of trivalent actinides in calcium chloride rich brine solutions were investigated and a thermodynamic model derived. The solubility of Plutonium in saline brine systems was studied under reducing and non-reducing conditions and is described within a new thermodynamic model. The influence of dissolved carbonate on Americium and Plutonium solubility in MgCl{sub 2} solutions was investigated and quantitative information on Am and Pu solubility limits in these systems derived. Thermodynamic constants and model parameter derived in this work are implemented in the Thermodynamic Reference Database THEREDA owned by BfS. According to the quality assurance approach in THEREDA, is was necessary to publish parts of this work in peer-reviewed scientific journals. The publications are focused on solubility experiments, spectroscopy of aquatic and solid species and thermodynamic data. (Neck et al., Pure Appl. Chem., Vol. 81, (2009), pp. 1555-1568., Altmaier et al., Radiochimica Acta, 97, (2009), pp. 187-192., Altmaier et al., Actinide Research Quarterly, No 2., (2011), pp. 29-32.).

  10. Preliminary results from uranium/americium affinity studies under experimental conditions for cesium removal from NPP ''Kozloduy'' simulated wastes solutions

    International Nuclear Information System (INIS)

    Nikiforova, A.; Kinova, L.; Peneva, C.; Taskaeva, I.; Petrova, P.

    2005-01-01

    We use the approach described by Westinghouse Savannah River Company using ammonium molybdophosphate (AMP) to remove elevated concentrations of radioactive cesium to facilitate handling waste samples from NPP K ozloduy . Preliminary series of tests were carried out to determine the exact conditions for sufficient cesium removal from five simulated waste solutions with concentrations of compounds, whose complexing power complicates any subsequent processing. Simulated wastes solutions contain high concentrations of nitrates, borates, H 2 C 2 O 4 , ethylenediaminetetraacetate (EDTA) and Citric acid, according to the composition of the real waste from the NPP. On this basis a laboratory treatment protocol was created. This experiment is a preparation for the analysis of real waste samples. In this sense the results are preliminary. Unwanted removal of non-cesium radioactive species from simulated waste solutions was studied with gamma spectrometry with the aim to find a compromise between on the one hand the AMP effectiveness and on the other hand unwanted affinity to AMP of Uranium and Americium. Success for the treatment protocol is defined by proving minimal uptake of U and Am, while at the same time demonstrating good removal effectiveness through the use of AMP. Uptake of U and Am were determined as influenced by oxidizing agents at nitric acid concentrations, proposed by Savannah River National laboratory. It was found that AMP does not significantly remove U and Am when concentration of oxidizing agents is more than 0.1M for simulated waste solutions and for contact times inherent in laboratory treatment protocol. Uranium and Americium affinity under experimental conditions for cesium removal were evaluated from gamma spectrometric data. Results are given for the model experiment and an approach for the real waste analysis is chosen. Under our experimental conditions simulated wastes solutions showed minimal affinity to AMP when U and Am are most probably in

  11. Adsorption-desorption characteristics of plutonium and americium with sediment particles in the estuarine environment: studies using plutonium-237 and americium-241

    International Nuclear Information System (INIS)

    Murray, C.N.; Fukai, R.

    1975-01-01

    The particle formation of plutonium and americium, their adsorption onto fresh water sediments and the desorption from the sediments in sea water were studied in the Laboratory under simulated river-estuary conditions, using γ-emitting plutonium-237 and americium-241. The results of the experiments show that the particle formation of plutonium depends on its valence states, on pH and on the salinity of the medium. For river water at pH4, some 25%, 20% and 30% of the added 237 Pu was in particulate form, larger than 0.45 μm, for Pu (III), Pu (IV) and Pu (VI), respectively, while 65%, 90% and 50% of the respective valence states was associated with particles at pH 8. In sea water the general pattern remains similar, although Pu (VI) is more soluble in sea water owing to higher ligand concentrations for carbonate and bicarbonate complexes. The pH-dependency of particle formation of Am (III) is more steep than that of plutonium and seems to be influenced by colloidal substances occurring in the experimental media. The adsorption-desorption characteristics of plutonium and americium with the sediment in river water as well as sea water reflect the characteristics of their particle formation, being dependent upon such properties as valence states, the pH and salinity of the medium. A sewage effluent added to the media has small but measurable effects on the adsorption-desorption processes of plutonium. (author)

  12. Plutonium-239 and americium-241 uptake by plants from soil. Final report

    International Nuclear Information System (INIS)

    Brown, K.W.

    1979-03-01

    Alfalfa was grown in soil contaminated with plutonium-239 dioxide (239PuO2) at a concentration of 29.7 nanocuries per gram (nCi/g). In addition to alfalfa, radishes, wheat, rye, and tomatoes were grown in soils contaminated with americium-241 nitrate (241Am(NO3)3) at a concentration of 189 nCi/g. The length of exposure varied from 52 days for the radishes to 237 days for the alfalfa. The magnitude of plutonium incorporation by the alfalfa as indicated by the concentration ratio, 0.0000025, was similar to previously reported data using other chemical forms of plutonium. The results did indicate, however, that differences in the biological availability of plutonium isotopes do exist. All of the species exposed to americium-241 assimilated and translocated this radioisotope to the stem, leaf, and fruiting structures. The magnitude of incorporation as signified by the concentration ratios varied from 0.00001 for the wheat grass to 0.0152 for the radishes. An increase in the uptake of americium also occurred as a function of time for four of the five plant species. Evidence indicates that the predominant factor in plutonium and americium uptake by plants may involve the chelation of these elements in soils by the action of compounds such as citric acid and/or other similar chelating agents released from plant roots

  13. Possibility of obtaining enriched americium-242g by the elution of recoil atoms from zeolite

    Energy Technology Data Exchange (ETDEWEB)

    Shafiev, A I; Vityutnev, V M; Ivanov, V M; Yakovlev, G N

    1974-12-31

    On the example of production the possibility of obtaining enriched actinide isotopes by the elution of recotl atoms with the use of a zeolite- americium-241 target was shown. The enrichment factor and the recoil atoms of / sup 242g/Am yield depend on preliminary target treatment and solution composition used for elution. (auth)

  14. Environmental impacts of the release of a transuranic actinide, americium-241, from a contaminated facility

    Energy Technology Data Exchange (ETDEWEB)

    Want, J.; Merry-Libby, P.

    1985-10-29

    Americium-241 is widely used as a radiation source, but it also has some potential risk if taken into the body because of its high dose conversion factor. Although the radiotoxicity of americium-241 is small compared to other transuranic actinides, its effects on the reproductive system and on development of the placenta are more damaging than the effects of plutonium-239. In Ohio, a gemologist's laboratory was contaminated with americium-241. Prior to decontamination of the laboratory, potential radiological impacts to the surrounding environment were assessed. A hypothetical fire accident resulting in a unit release (1 curie) was assumed. Potential radiological impacts were simulated using an atmospheric dispersion and dosimetry model with local meteorological data, population census data, and detailed information regarding the neighborhood. The results indicate that there could have been a significant impact on nearby residents from americium-241 via atmospheric dispersion if a major catastrophic release had occurred prior to contamination and decommissioning of the laboratory. 14 refs., 3 figs., 2 tabs.

  15. Explosion of cation exchange column in americium recovery service, Hanford plant, August 30, 1976

    International Nuclear Information System (INIS)

    1976-01-01

    This document is a collection of thirty references related to the explosion of the cation exchange column in the Americium Recovery Service of the Hanford Atomic Products Operation, Richland, Washington, on August 30, 1976. Some of the documents are related to the design and safety studies, while others refer to the accident and resulting decontamination efforts, investigations, and legal consequences

  16. Total and Compound Formation Cross Sections for Americium Nuclei: Recommendations for Coupled-Channels Calculations

    Energy Technology Data Exchange (ETDEWEB)

    Escher, J. E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2017-04-11

    Calculations for total cross sections and compound-nucleus (CN) formation cross sections for americium isotopes are described, for use in the 2017 NA-22 evaluation effort. The code ECIS 2006 was used in conjunction with Frank Dietrich's wrapper `runtemplate'.

  17. Plutonium and americium in arctic waters, the North Sea and Scottish and Irish coastal zones

    DEFF Research Database (Denmark)

    Hallstadius, L.; Aarkrog, Asker; Dahlgaard, Henning

    1986-01-01

    Plutonium and americium have been measured in surface waters of the Greenland and Barents Seas and in the northern North Sea from 1980 through 1984. Measurements in water and biota, Fucus, Mytilus and Patella, were carried out in North-English and Scottish waters in 1982 and Fucus samples were co...

  18. National low-level waste management program radionuclide report series, Volume 14: Americium-241

    International Nuclear Information System (INIS)

    Winberg, M.R.; Garcia, R.S.

    1995-09-01

    This report, Volume 14 of the National Low-Level Waste Management Program Radionuclide Report Series, discusses the radiological and chemical characteristics of americium-241 ( 241 Am). This report also includes discussions about waste types and forms in which 241 Am can be found and 241 Am behavior in the environment and in the human body

  19. Radiochemical separation and alpha-spectrometric determination of Americium in different matrixes

    International Nuclear Information System (INIS)

    Radenkovic, M.; Joksic, J.; Paligoric, D.

    2009-01-01

    A method of separation and alpha-spectrometric determination of americium, developed in VINCA Institute of Nuclear Sciences is described in the paper. The procedure is convenient to be used for 241 Am determination in environmental matrixes as well as samples of human origin if a very small concentrations are expected, using 243 Am as a tracer for radiochemical yield recovery. (author) [sr

  20. Biokinetic study of plutonium and americium associated to the particulates of soil

    International Nuclear Information System (INIS)

    Espinosa, A.; Aragon, A.; Martinez, J.; Iranzo, C.E.

    1996-01-01

    The object of this study is to determine the biokinetic parameters of different Plutonium isotopes and Americium inhaled in the state in which they are found in the environment as a result of their deposition in the soil, from an aviation accident that generated different plutonium oxides. to achieve this objective, two lines of work planned. One was the determination of the mineralogical composition and associations that plutonium and americium present in that soil 22 years after the nuclear accident. Other studies were directed to determine the biokinetic of the plutonium isotopes and americium (contained in the dust) deposited tracheally and inhaled by laboratory animals (rats) and in vitro experiments by pulmonary leaching simulation. The in vivo tests have been developed in NRPB (U.K.) and the in vitro experiment, geochemical associations studies, assessment of internal doses to humans resulting from intake of plutonium and americium bearing dusts present in the contaminated area and establishment of ALIs for inhalation, were carried out in CIEMAT (Spain). In this work only determinations and experiments carried out by CIEMAT are includes as a part of the EU Project ''INHALATION AND INGESTION OF RADIONUCLIDES'' contract: FI3P-CT920064a. (Author) 10 refs

  1. Speciation and bioavailability of plutonium and americium in the Irish Sea and other marine ecosystems

    International Nuclear Information System (INIS)

    Vives i Batlle, J.

    1993-12-01

    Since the late 1960s, the Irish Sea has become a repository for a variety of radio-elements originating mainly in discharges from the British Nuclear Fuels (BNF) plc. Sellafield reprocessing complex located on the Cumbrian coast. In particular, transuranium nuclides such as plutonium, americium and curium (the main constituents of the α-emitting discharges) have become incorporated into every marine compartment by a variety of mechanisms, many of which are not well understood. Although extensive studies have been carried out in the near-field (eastern Irish Sea, especially in the vicinity of the discharge point and collateral muddy sediments), comparatively little had been done to assess the long-term behaviour and bioavailability of plutonium and americium in the far-field, e.g., the western Irish Sea, prior to the present study. In this dissertation, the results of an extensive research programme, undertaken in order to improve and refine our understanding of the behaviour of plutonium and americium in the marine environment, are presented. Specifically, the thesis details the results of (and conclusions deduced from) a series of experiments in which the physical and chemical speciation, colloidal association, mobility and bioavailability of plutonium and americium were examined in diverse environments including the Irish Sea and the Mediterranean. (author)

  2. Determination of specific activity of americium and plutonium in selected environmental samples

    International Nuclear Information System (INIS)

    Trebunova, T.

    1999-01-01

    The aim of this work was development of method for determination of americium and plutonium in environmental samples. Developed method was evaluated on soil samples and after they was applied on selected samples of fishes (smoked mackerel, herring and fillet from Alaska hake). The method for separation of americium is based on liquid separation with Aliquate-336, precipitation with oxalic acid and using of chromatographic material TRU-Spec TM .The intervals of radiochemical yields were from 13.0% to 80.9% for plutonium-236 and from 10.5% to 100% for americium-241. Determined specific activities of plutonium-239,240 were from (2.3 ± 1.4) mBq/kg to (82 ± 29) mBq/kg, the specific activities of plutonium-238 were from (14.2 ± 3.7) mBq/kg to (708 ± 86) mBq/kg. The specific activities of americium-241 were from (1.4 ± 0.9) mBq/kg to (3360 ± 210) mBq/kg. The fishes from Baltic Sea as well as from North Sea show highest specific activities then fresh-water fishes from Slovakia. Therefore the monitoring of alpha radionuclides in foods imported from territories with nuclear testing is recommended

  3. Studies on the Interaction of a Novel 6,6''-bis(1,2,4-triazin-3-yl)- 2,2':6',2''-terpyridine Ligand with Lanthanide(III) Ions and Americium(III)

    International Nuclear Information System (INIS)

    Lewis, Frank W.; Harwood, Laurence M.; Hudson, Michael J.; Drew, Michael G.B.; Modolo, Giuseppe; Sypula, Michal; Desreux, Jean F.; Bouslimani, Nouri; Vidick, Geoffrey

    2010-01-01

    The new solvent extraction reagent 6,6''-bis(5,5,8,8-tetramethyl- 5,6,7,8-tetrahydro-1,2,4-benzo-triazin-3-yl)-2,2':6',2''-terpyridine (CyMe 4 -BTTP) has been synthesized in 4 steps from 2,2':6',2''-terpyridine. Detailed NMR and mass spectrometry studies indicate that the ligand forms 1:2 complexes with lanthanide(III) perchlorates where the aliphatic rings are conformationally constrained whereas 1:1 complexes are formed with lanthanide(III) nitrates where the aliphatic rings are conformationally mobile. An optimized structure of the 1:2 solution complex with Yb(III) was obtained from the relative magnitude of the induced paramagnetic shifts. X-ray crystallographic structures of the ligand and of its 1:1 complex with Y(III) were also obtained. In the absence of a phase-modifier, CyMe 4 -BTTP in 1-octanol showed a maximum distribution coefficient of Am(III) of 0.039 (±20%) and a maximum separation factor of Am(III) over Eu(III) of 12.0 from nitric acid solution. The metal(III) cations are extracted as the 1:1 complex from nitric acid solutions. The generally low distribution coefficients observed compared with the BTBPs arise because the 1:1 complex of CyMe 4 -BTTP is considerably less hydrophobic than the 1:2 complexes formed by the BTBPs. In M(BTTP) 3+ complexes, there is a competition between the nitrate ions and the ligand for the complexation of the metal. (authors)

  4. Interaction and diffusion transport of americium in soils

    Energy Technology Data Exchange (ETDEWEB)

    Ramirez-Guinart, Oriol; Rigol, Anna; Vidal, Miquel [Analytical Chemistry department, Faculty of Chemistry, University of Barcelona, Marti i Franques 1-11, 08028, Barcelona (Spain)

    2014-07-01

    The final disposal of High Level Radioactive Wastes (HLRW) is based on its long-term storage in underground facilities located in geological stable sites with a multi-barrier system, the so called Deep Geological Repositories (DGR), that will keep HLRW confined for >10.000 years. After this period of time, leachates rich in long-live radioisotopes might escape from DGR and start to transport towards the biosphere. There is still a lack of information concerning the interaction and transport in soils of some radionuclides present in HLRW, especially for radionuclides that present a high sorption, such as americium (Am). Having reliable information about the mobility of radionuclides in soils is crucial in order to develop risk assessment models and to take proper decisions in case of soil contamination. The aim of the present work was, by means of laboratory scale experiments, to study the interaction and, for first time, to evaluate the diffusion transport of {sup 241}Am in soils. The {sup 241}Am interaction in soils was assessed by applying sorption batch assays to 20 soil samples with contrasted edaphic properties which allowed us to quantify the solid-liquid distribution coefficient (K{sub d}) and desorption percentage. K{sub d} (Am) values ranged from 10{sup 3} to 10{sup 5} L kg{sup -1} and desorption percentages were always less than 2% which denoted a high capacity of the soil to incorporate the Am and a low reversibility of the sorption process. The influence of soil properties in {sup 241}Am interaction was studied by means of multiple linear and multivariate regressions. Although a single correlation between K{sub d} (Am) values and a soil property was not found, the main properties affecting {sup 241}Am interaction in soils were soil pH, carbonate and organic matter contents in the soil. Finally, additional batch assays at different controlled pH were done to study Am sorption as a function of the contact solution pH. A variation of the Am sorption

  5. Local Structure in Americium and Californium Hexa-cyanoferrates - Comparison with Their Lanthanide Analogues

    International Nuclear Information System (INIS)

    Dupouy, G.; Bonhoure, I.; Dumas, Th.; Moisy, Ph.; Petit, S.; Den Auwer, Ch.; Conradson, St.D.; Hennig, Ch.; Scheinost, A.C.; Le Naour, C.; Simoni, E.

    2011-01-01

    Metal hexa-cyanoferrates are well known molecular solids for a large variety of cations, although very little has been described for actinide adducts. Two new members of actinide(III) hexa-cyanoferrates were synthesized with the cations americium and californium. They were structurally characterized by infrared and X-ray absorption spectroscopy. Combined EXAFS data at the iron K edge and actinide L 3 edge provide evidence for a three-dimensional model for these two new compounds. Structural data in terms of bond lengths were compared to those reported for the parent lanthanide(III) compounds, neodymium and gadolinium hexa-cyanoferrates, respectively: the americium compound with (KNd(III)Fe(II)-Fe-III(CN) 6 .4H 2 O and the californium compound with (KGd(III)Fe(II)(CN) . 3.5H 2 O and (KGd(III)Fe(II)(CN) 6 .3H 2 O. This comparison between actinide and lanthanide homologues has been carried out on the basis of ionic radii considerations. The americium and neodymium environments appear to be very similar and are arranged in a tri-capped trigonal prism polyhedron of coordination number 9 (CN: 9), in which the americium atom is bonded to six nitrogen atoms and to three water molecules. For the californium adduct, a similar comparison and bond length and angle values derived from EXAFS studies suggest that the californium cation sits in a bi-capped trigonal prism (CN: 8) as in (KGd(III)Fe(II)(CN) 6 . 3H 2 O. This arrangement differs from that in the structure of (KGd(III)Fe(II)(CN) 6 .3.5H 2 O, in which the gadolinium atom is surrounded by 9 atoms. This is one of the rare pieces of information revealed by EXAFS spectroscopy for americium and californium in comparison to lanthanide atoms in molecular solid compounds. A discussion on the decrease in bond length and coordination number from americium to californium is also provided, on the basis of crystallographic results reported in the literature for actinide(III) and lanthanide(III) hydrate series. (authors)

  6. Electric resistivity of 241-americium and 244-curium metals. Creation of defects and isochronous annealing of 241-americium metal after self-irradiation

    International Nuclear Information System (INIS)

    Schenkel, R.

    1977-03-01

    The temperature dependence of the electrical resistivity of thin films of bulk 241 Am metal were measured between 300 and 4.5 K. The room temperature resistivity was found to be 68.90μΩcm. At room temperature the electrical resistivity of americium increases with pressure (3% up to 13 kbar). The application of 13 kbar pressure did not change the low temperature power law in the electrical resistivity. The resistivity vs temperature curve can be explained by assuming s-d scattering of conduction electrons. The localized 5f electrons are considered to be about 5eV below the Fermi level. Americium therefore should be the first lanthanide-like element in the actinide series. The defect production due to self-irradiation damage was studied by measuring the increase of the resistivity at 4.2 K over a period of 738 h. A saturation resistivity of 16.036 μΩcm was found corresponding to a defect concentration of about 0.22 a/o. After isochronal annealing two recovery stages were observed at about 65 and 145 K. The two stages shift with increasing initial defect concentration to lower temperatures. Estimates of the activation energies and the reaction order were made and possible defect reactions suggested. The magnetic contribution to the electrical resistivity of curium, which shows an antiferromagnetic transition at 52.5 k, was obtained by subtracting the resistivity of americium (to be considered as phonon part). Comparison with theoretical models were made. At low temperatures the measurements are strongly affected by self-irradiation damage [drho/dt(t=0)=9.8μΩcm/h

  7. 1976 Hanford americium-exposure incident: accident description

    International Nuclear Information System (INIS)

    McMurray, B.J.

    1982-01-01

    An accident is described, involving the explosion of an ion-exchange column containing about 100 g of 241 Am. A chemical operator was injured in this accident, receiving acid burns and superficial cuts on the upper part of his body. From 1 to 5 curies of 241 Am is estimated to have been deposited on the injured worker and on his clothing

  8. Mycoremediation. The study of transfer factor for plutonium and americium uptake from the ground

    International Nuclear Information System (INIS)

    Dusan Galanda; Lubomir Matel; Jana Strisovska; Silvia Dulanska

    2014-01-01

    In our scientific research we have monitored mycoremediation's properties of oyster mushrooms in cultivation on the soil what is contaminated by solutions with radioactive isotopes of 239 Pu and 241 Am with known activity. We monitored specific activities of absorbed radionuclides in fruiting bodies and chemical forms of radionuclides which were compared to calculated specific activities of two background samples of oyster mushrooms intended for consumer purpose. We determined distributive coefficients between the ground and the fruiting body of oyster mushrooms. The average value which was obtained for the transfer factor for plutonium was 0.72 and for americium 3.97. To evaluate a quantity of absorbed radionuclides we used a method of liquid extraction. The emitting alpha radiation of alpha radionuclides was detected by spectrometry. For defining individual fractions of plutonium and americium that are contained in mushroom bodies was used the sequential leaching method. (author)

  9. Standard test method for quantitative determination of americium 241 in plutonium by Gamma-Ray spectrometry

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    1994-01-01

    1.1 This test method covers the quantitative determination of americium 241 by gamma-ray spectrometry in plutonium nitrate solution samples that do not contain significant amounts of radioactive fission products or other high specific activity gamma-ray emitters. 1.2 This test method can be used to determine the americium 241 in samples of plutonium metal, oxide and other solid forms, when the solid is appropriately sampled and dissolved. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  10. Transmutation of americium and curium incorporated in zirconia-based host materials

    International Nuclear Information System (INIS)

    Raison, P.E.

    2001-01-01

    Presented are studies involving the incorporation of americium and curium in zirconia-based materials. First explored was the pseudo ternary system AmO 2 -ZrO 2 -Y 2 O 3 . It was determined that selected Y-CSZ materials can incorporate significant quantities of americium oxide and remain cubic single-phase. The cell parameters of these fluorite-type products were established to be linear with the AmO 2 content. The Cm 2 O 3 -ZrO 2 system was also investigated. It was found that at 25 mol% of CmO 1.5 , the Cm(III) stabilized zirconia in its cubic form (a = 5.21 ±0.01 Angstrom). At higher and lower concentrations, diphasic materials were encountered. At 50 mol% of CmO 1.5 , a pyrochlore oxide - Cm 2 Zr 2 O 7 - is formed (a = 10.63 ±0.02 Angstrom). (author)

  11. Contemporary state of plutonium and americium in the soils of Palesse state radiation-ecological reserve

    International Nuclear Information System (INIS)

    Papenia, M.V.; Sokolik, G.A.; Ovsiannikova, S.V.; Voinikava, E.V.; Svirschevsky, S.F.; Brown, J.; Skipperud, L.

    2010-01-01

    Full text: At present, the most important alpha-emitting radionuclides of Chernobyl origin are Pu 238, Pu 239, Pu 240 and Am 241. They are classified as the most dangerous group of radionuclides in view of the long half-lives and high radiotoxicity. The main part of alpha-emitted radionuclides is located within the Palesse State Radiation-Ecological Reserve. One of the most important factors determining the radioecological situation in the contaminated ecosystems is the physicochemical forms of radionuclides in a soil medium. Radionuclide species determine the radionuclide entrance into the soil solutions, their redistribution in soil profiles and the 'soil - plant' and the 'soil - surface, ground or underground water' systems as well as spreading beyond the contaminated area. The present work is devoted to investigation of state and migration ability of plutonium and americium in soils of the Palesse state radiation-ecological reserve after more than 20 years from the Chernobyl accident. The objects of investigation were mineral and organic soils sampled in 2008 with the step of 5 cm to the depth of 25-30 cm. The forms of plutonium and americium distinguishing by association with the different components of soil and by potential for migration in the soil medium were studied using the method of sequential selective extraction according to the modified Tessier scheme. Activities of Pu 238, Pu 239, Pu 240 and Am 241 in the samples were determined by the method of radiochemical analysis with alpha-spectrometer radionuclide identification. The dominant part of plutonium and americium in the soils is in immobile forms. Nowadays, radionuclide portions in water soluble and reversibly bound forms do not exceed 9.4 % of radionuclide content in the soil. In mineral soil samples, the radionuclide portions in these fractions exceed the corresponding portions in organic ones. In both mineral and organic soils, the portions of mobile americium are higher than plutonium. The

  12. High-purity germanium detection system for the in vivo measurement of americium and plutonium

    International Nuclear Information System (INIS)

    Tyree, W.H.; Falk, R.B.; Wood, C.B.; Liskey, R.W.

    1976-01-01

    A high-purity germanium (HPGe) array, photon-counting system has been developed for the Rocky Flats Plant Body-Counter Medical Facility. The newly improved system provides exceptional resolutions of low-energy X-ray and gamma-ray spectra associated with the in vivo deposition of plutonium and americium. Described are the operational parameters of the system and some qualitative results illustrating detector performance for the photon emissions produced from the decay of plutonium and americium between energy ranges from 10 to 100 kiloelectron volts. Since large amounts of data are easily generated with the system, data storage, analysis, and computer software developments continue to be an essential ingredient for processing spectral data obtained from the detectors. Absence of quantitative data is intentional. The primary concern of the study was to evaluate the effects of the various physical and electronic operational parameters before adding those related entirely to a human subject

  13. Electrodeposition of americium on a liquid cadmium cathode from a molten salt bath

    International Nuclear Information System (INIS)

    Laplace, A.; Lacquement, J.; Maillard, C.; Donner, L.

    2004-01-01

    A high-activity experiment involving the electrode position of americium on a liquid cadmium cathode from a LiCl-KCl eutectic with about 3 g of AmO 2 was conducted in a shielded cell in the ATALANTE complex. After describing the electrolyzer and the experimental conditions, the authors discuss the preparation of the LiCl-KCl-AmCl 3 solution and briefly review its electrochemical properties. It was clearly confirmed that Am(III) reduction on an inert solid cathode occurs in two steps forming Am(II) before Am(0), whereas only one reduction step was observed on liquid cadmium. The main results of this study concern americium electrode position on the liquid cadmium cathode (recovery yields, current densities, problems encountered). The solvent properties of cadmium for actinide/lanthanide separation are discussed. (authors)

  14. Quantitative determination of americium and curium in solutions using potassium tungstophosphate

    International Nuclear Information System (INIS)

    Chistyakov, V.M.; Baranov, A.A.; Erin, E.A.; Timoaeev, G.A.

    1990-01-01

    Two methods of americium (4) and curium (4) titration-replacement and redox ones - have been considered. According to the replacement method thorium nitrate solution was used as a titrant and the final point of titration was determined spectophotometrically. Using the method developed, on the basis of experimental data, the composition of thorium (4) complex with potassium tungstophosphate was determined. In case of the redox titration sodium nitrite was used, and the final titration point was indicated either spectrophotometrically or potentiometrically

  15. Determination of americium and plutonium in autopsy tissue: methods and problems

    International Nuclear Information System (INIS)

    Boyd, H.A.; Eutsler, B.C.; McInroy, J.F.

    1979-01-01

    The current methods used by the tissue analysis program at LASL for the determination of americium and plutonium in autopsy tissue are described. Problems affecting radiochemical yield are discussed. Included are problems associated with sample preparation, separation of plutonium from large amounts of bone ash, and reagent contamination. The average 242 Pu tracer yield for 1800 Pu determinations is 78 +- 12%. The average 242 Am tracer yield is 85 +- 7% for 40 determinations

  16. Final Radiological Assessment of External Exposure for CLEAR-Line Americium Recovery Operations

    Energy Technology Data Exchange (ETDEWEB)

    Davis, Adam C. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Belooussova, Olga N. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hetrick, Lucas Duane [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2014-11-12

    Los Alamos National Laboratory is currently planning to implement an americium recovery program. The americium, ordinarily isotopically pure 241Am, would be extracted from existing Pu materials, converted to an oxide and shipped to support fabrication of americium oxide-beryllium neutron sources. These operations would occur in the currently proposed Chloride Extraction and Actinide Recovery (CLEAR) line of glove boxes. This glove box line would be collocated with the currently-operational Experimental Chloride Extraction Line (EXCEL). The focus of this document is to provide an in-depth assessment of the currently planned radiation protection measures and to determine whether or not further design work is required to satisfy design-goal and ALARA requirements. Further, this document presents a history of americium recovery operations in the Department of Energy and high-level descriptions of the CLEAR line operations to provide a basis of comparison. Under the working assumptions adopted by this study, it was found that the evaluated design appears to mitigate doses to a level that satisfies the ALARA-in-design requirements of 10 CFR 835 as implemented by the Los Alamos National Laboratory procedure P121. The analyses indicate that extremity doses would also meet design requirements. Dose-rate calculations were performed using the radiation transport code MCNP5 and doses were estimated using a time-motion study developed in consort with the subject matter expert. A copy of this report and all supporting documentation are located on the Radiological Engineering server at Y:\\Rad Engineering\\2013 PROJECTS\\TA-55 Clear Line.

  17. Experimental studies to validate model calculations and maximum solubility limits for Plutonium and Americium

    International Nuclear Information System (INIS)

    2017-01-01

    This report focuses on studies of KIT-INE to derive a significantly improved description of the chemical behaviour of Americium and Plutonium in saline NaCl, MgCl 2 and CaCl 2 brine systems. The studies are based on new experimental data and aim at deriving reliable Am and Pu solubility limits for the investigated systems as well as deriving comprehensive thermodynamic model descriptions. Both aspects are of high relevance in the context of potential source term estimations for Americium and Plutonium in aqueous brine systems and related scenarios. Americium and Plutonium are long-lived alpha emitting radionuclides which due to their high radiotoxicity need to be accounted for in a reliable and traceable way. The hydrolysis of trivalent actinides and the effect of highly alkaline pH conditions on the solubility of trivalent actinides in calcium chloride rich brine solutions were investigated and a thermodynamic model derived. The solubility of Plutonium in saline brine systems was studied under reducing and non-reducing conditions and is described within a new thermodynamic model. The influence of dissolved carbonate on Americium and Plutonium solubility in MgCl 2 solutions was investigated and quantitative information on Am and Pu solubility limits in these systems derived. Thermodynamic constants and model parameter derived in this work are implemented in the Thermodynamic Reference Database THEREDA owned by BfS. According to the quality assurance approach in THEREDA, is was necessary to publish parts of this work in peer-reviewed scientific journals. The publications are focused on solubility experiments, spectroscopy of aquatic and solid species and thermodynamic data. (Neck et al., Pure Appl. Chem., Vol. 81, (2009), pp. 1555-1568., Altmaier et al., Radiochimica Acta, 97, (2009), pp. 187-192., Altmaier et al., Actinide Research Quarterly, No 2., (2011), pp. 29-32.).

  18. Uptake and effects of americium-241 on a brackish-water amphipod

    Energy Technology Data Exchange (ETDEWEB)

    Hoppenheit, M.; Murray, C.N.; Woodhead, D.S.

    1980-01-01

    The present paper reports the results of experimental work undertaken using the brackish-water amphipod Gammarus duebeni duebeni and the transuranium nuclide americium-241. Data on the accumulation of this actinide showed that the larger fraction of the total body burden is associated with the exoskeleton. It was found that the body burden remained constant in the range pH 8.0-6.5 even though the water concentration changed markedly. It would thus appear that the concept of a concentration factor should be re-examined and it is proposed that a factor should be defined in terms of environmental and chemical parameters which represent the bioavailable fraction of the actinide. The effect of americium on survival and moulting was studied at two activity concentrations; the dose rates and absorbed doses under the experimental conditions employed have been estimated. The differences in survival rates between the control and irradiated groups were statistically analyzed and the significant difference at the higher concentration is believed to be due to a synergism between physiological stress and radiotoxicity of americium rather than the chemical toxicity of the element.

  19. Uptake and effects of americium-241 on a brackish-water amphipod

    International Nuclear Information System (INIS)

    Hoppenheit, M.; Murray, C.N.; Woodhead, D.S.

    1980-01-01

    The present paper reports the results of experimental work undertaken using the brackish-water amphipod Gammarus duebeni duebeni and the transuranium nuclide americium-241. Data on the accumulation of this actinide showed that the larger fraction of the total body burden is associated with the exoskeleton. It was found that the body burden remained constant in the range pH 8.0-6.5 even though the water concentration changed markedly. It would thus appear that the concept of a concentration factor should be re-examined and it is proposed that a factor should be defined in terms of environmental and chemical parameters which represent the bioavailable fraction of the actinide. The effect of americium on survival and moulting was studied at two activity concentrations; the dose rates and absorbed doses under the experimental conditions employed have been estimated. The differences in survival rates between the control and irradiated groups were statistically analyzed and the significant difference at the higher concentration is believed to be due to a synergism between physiological stress and radiotoxicity of americium rather than the chemical toxicity of the element. (orig.) [de

  20. Adsorption-Desorption Characteristics of Plutonium and Americium with Sediment Particles in the Estuarine Environment

    International Nuclear Information System (INIS)

    Murray, C.N.; Fukai, R.

    1976-01-01

    The particle formation of plutonium and americium, their adsorption onto fresh water sediments and the desorption from the sediments in sea water were studied in the Laboratory under simulated river-estuary conditions, using γ-emitting plutonium-237 and americium-241. The results of the experiments show that the particle formation of plutonium depends on its valence states, on pH and on the salinity of the medium. For river water at pH4, some 25%, 20% and 30% of the added 237 Pu was in particulate form, larger than 0.45pm, for Pu (III), Pu (IV) and Pu (VI), respectively, while 65%, 90% and 50% of the respective valence states was associated with particles at pH 8. In sea water the general pattern remains similar, although Pu (VI) is more soluble in sea water owing to higher ligand concentrations for carbonate and bicarbonate complexes. The pH-dependency of particle formation of Am (III) is more steep than that of plutonium and seems to be influenced by colloidal substances occurring in the experimental media. The adsorption-desorption characteristics of plutonium and americium with the sediment in river water as well as sea water reflect the characteristics of their particle formation, being dependent upon such properties as valence states, the pH and salinity of the medium. A sewage effluent added to the media has small but measurable effects on the adsorption-desorption processes of plutonium. (author)

  1. Influence of dissolved organic substances in groundwater on sorption behavior of americium and neptunium

    International Nuclear Information System (INIS)

    Boggs, S. Jr.; Seitz, M.G.

    1984-01-01

    Groundwaters typically contain dissolved organic carbon consisting largely of high molecular weight compounds of humic and fulvic acids. To evaluate whether these dissolved organic substances can enhance the tranport of radionuclides through the groundwater system, experiments were conducted to examine the sorption of americium and neptunium onto crushed basalt in the presence of dissolved humic- and fulvic-acid organic carbon introduced into synthetic groundwater. The partitioning experiments with synthetic groundwater show that increasing the concentration of either humic or fulvic acid in the water has a significant inhibiting effect on sorption of both americium and neptunium. At 22 0 C, adsorption of these radionuclides, as measured by distribution ratios (the ratio of nuclide sorbed onto the solid to nuclide in solution at the end of the experiment), decreased by 25% to 50% by addition of as little as 1 mg/L dissolved organic carbon and by one to two orders of magnitude by addition of 100 to 200 mg/L dissolved organic carbon. Distribution ratios measured in solutions reacted at 90 0 C similarly decreased with the addition of dissolved organic carbon but generally ranged from one to two orders of magnitude higher than those determined in the 22 0 C experiment. These results suggest that organic carbon dissolved in deep groundwaters may significantly enhance the mobility of radionuclides of americium and neptunium. 23 references, 5 figures, 11 tables

  2. Radioanalytical determination of plutonium and americium using ion exchange and extraction chromatography technique in urine

    International Nuclear Information System (INIS)

    Santhanakrishnan, V.; Sreedevi, K.R.; Rajaram, S.; Ravi, P.M.

    2011-01-01

    The use of anion exchange chromatography for the separation of Pu and extraction chromatography technique for the separation of Am from urine samples was studied. In the earlier method, Pu separation was carried out by anion exchange chromatography followed by Am separation by cation exchange chromatography. The chemical recovery of Am obtained by cation exchange separation method was inconsistent and low in the range 30-70%. In this study, the average Pu recovery obtained using anion exchange chromatography was 89.2 with standard deviation of 10.4 and the average Am recovery obtained using extraction chromatography with TRU resin was 77.4 with standard deviation of 14.8. Moreover, Am separation could be completed within three hours using the TRU column compared to two days that were required for the cation exchange chromatography. (author)

  3. Experimental findings on actinide recovery utilizing oxidation by peroxydisulfate followed by ion exchange: Fuel cycle research & development

    Energy Technology Data Exchange (ETDEWEB)

    Hobbs, D. T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Shehee, T. C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2015-08-31

    Our research seeks to determine if inorganic ion-exchange materials can be exploited to provide effective minor actinide (Am, Cm) separation from lanthanides. Previous work has established that a number of inorganic and UMOF ion-exchange materials exhibit varying affinities for actinides and lanthanides, which may be exploited for effective separations. During FY15, experimental work focused on investigating methods to oxidize americium in dilute nitric and perchloric acid with subsequent ion-exchange performance measurements of ion exchangers with the oxidized americium in dilute nitric acid. Ion-exchange materials tested included a variety of alkali titanates. Americium oxidation testing sought to determine the influence that other redox active components may have on the oxidation of AmIII. Experimental findings indicated that CeIII, NpV, and RuII are oxidized by peroxydisulfate, but there are no indications that the presence of CeIII, NpV, and RuII affected the rate or extent of americium oxidation at the concentrations of peroxydisulfate being used.

  4. An experimental investigation of accumulation and transmutation behavior of americium in the MOX fuel irradiated in a fast reactor

    International Nuclear Information System (INIS)

    Osaka, Masahiko; Koyama, Shin-ichi; Maeda, Shigetaka; Mitsugashira, Toshiaki

    2005-01-01

    Americium isotopes generated in the MOX fuel irradiated in the experimental fast reactor JOYO were analyzed by applying a sophisticated radiochemical technique. Americium was isolated from the irradiated MOX fuel by a combined method of anion-exchange chromatography and oxidation of Am. The isotopic ratios of americium and its content were determined by thermal ionization mass spectroscopy and α-spectrometry, respectively. The americium isotopic ratio was similar for all the specimens, but was significantly different from that of PWR-MOX. On the basis of present analytical results, the accumulation and transmutation behavior of americium nuclides in a fast reactor is discussed from the viewpoints of neutron spectrum dependence and the isomeric ratio of the 241 Am capture reaction. The estimated isomeric ratio is about 87%, which is close to the latest evaluated value. A rapid estimation method of Am content by using the 240 Pu to 239 Pu ratio was adopted and proved to be valid for the spent fuel irradiated in the fast reactor

  5. Theoretical and experimental study of the bio-geochemical behaviour of americium 241 in simplified rhizosphere conditions. Application to a calcareous agricultural soil

    International Nuclear Information System (INIS)

    Perrier, T.

    2004-06-01

    significant extend and can represent up to 90% of the transported contamination. Therefore, it is impossible to estimate the mobility of americium in this part of the soil without taking into consideration the complexity and interconnection of the different processes involved: solid speciation of the element (mainly combined with carbonates and iron oxides), speciation in solution dependent of the microorganisms activity (complexing with citrate ions, pH etc.), and dynamics of the solutes transfer. The relative contribution of these inter-dependent processes remains difficult to evaluate with the macroscopic tools implemented. The modeling possibilities for this system are discussed on the basis of the different experimental data obtained (retention profiles, physico-chemical variations, K d ) and using a consistent thermodynamical database completed for the needs of this study. (J.S.)

  6. Europium (III) and americium (III) stability constants with humic acid

    International Nuclear Information System (INIS)

    Torres, R.A.; Choppin, G.R.

    1984-01-01

    The stability constants for tracer concentrations of Eu(III) and Am(III) complexes with a humic acid extracted from a lake-bottom sediment were measured using a solvent extraction system. The organic extractant was di(2-ethylhexyl)-phosphoric acid in toluene while the humate aqueous phase had a constant ionic strength of 0.1 M (NaClO 4 ). Aqueous humic acid concentrations were monitored by measuring uv-visible absorbances at approx.= 380 nm. The total carboxylate capacity of the humic acid was determined by direct potentiometric titration to be 3.86 +- 0.03 meq/g. The humic acid displayed typical characteristics of a polyelectrolyte - the apparent pKsub(a), as well as the calculated metal ion stability constants increased as the degree of ionization (α) increased. The binding data required a fit of two stability constants, β 1 and β 2 , such that for Eu, log β 1 = 8.86 α + 4.39, log β 2 = 3.55 α + 11.06 while for Am, log β 1 = 10.58 α + 3.84, log β 2 = 5.32 α + 10.42. With hydroxide, carbonate, and humate as competing ligands, the humate complex associated with the β 1 constant is calculated to be the dominant species for the trivalent actinides and lanthanides under conditions present in natural waters. (orig.)

  7. Accumulation of americium-241 in the biomass of aquatic plants of the Yenisei river: experimental study

    Energy Technology Data Exchange (ETDEWEB)

    Zotina, T.A.; Bolsunovsky, A.Y.A.; Bondareva, L.G. [Institute of Biophysics SB RAS, Akademgorodok, Krasnoyarsk (Russian Federation)

    2004-07-01

    Due to the operation of the Mining-and-Chemical Combine (Krasnoyarsk-26), which has been manufacturing weapons-grade plutonium for several decades, the Yenisei River is contaminated with transuranic elements (including {sup 241}Am). {sup 241}Am was found in the riverside soil, sediment and in the biomass of aquatic plants (Bolsunovsky et al., 1999, 2002). Aquatic plants are an important link in the migration of radionuclides in an aquatic ecosystem. In laboratory experiments, we investigated accumulation of {sup 241}Am by the submerged macrophyte from the Yenisei River: the pond weed (Elodea canadensis) and the aquatic moss (Fontinalis antipyretica), and release of {sup 241}Am from the biomass. The content of {sup 241}Am was measured on a Canberra (USA) gamma-spectrometer. The experiments showed that specific accumulation and concentration factors of {sup 241}Am in the plants were in inverse proportion to their biomass. We obtained new data on release of {sup 241}Am from the biomass of macrophyte. Americium-241 was more firmly fixed in the biomass of the aquatic moss. In 12 months, the biomass of the aquatic moss released about 30% of the initial americium activity into the water. To compare, the biomass of the pond weed released into the water medium up to 64% of the initial {sup 241}Am activity in 1.5 4 months. The release rate was dependent on the decomposition rate of the plant biomass. The experiments showed that submerged macrophyte of the Yenisei River can accumulate considerable activities of {sup 241}Am and retain americium for long periods of time in biomass. (author)

  8. Accumulation of americium-241 in the biomass of aquatic plants of the Yenisei river: experimental study

    International Nuclear Information System (INIS)

    Zotina, T.A.; Bolsunovsky, A.Y.A.; Bondareva, L.G.

    2004-01-01

    Due to the operation of the Mining-and-Chemical Combine (Krasnoyarsk-26), which has been manufacturing weapons-grade plutonium for several decades, the Yenisei River is contaminated with transuranic elements (including 241 Am). 241 Am was found in the riverside soil, sediment and in the biomass of aquatic plants (Bolsunovsky et al., 1999, 2002). Aquatic plants are an important link in the migration of radionuclides in an aquatic ecosystem. In laboratory experiments, we investigated accumulation of 241 Am by the submerged macrophyte from the Yenisei River: the pond weed (Elodea canadensis) and the aquatic moss (Fontinalis antipyretica), and release of 241 Am from the biomass. The content of 241 Am was measured on a Canberra (USA) gamma-spectrometer. The experiments showed that specific accumulation and concentration factors of 241 Am in the plants were in inverse proportion to their biomass. We obtained new data on release of 241 Am from the biomass of macrophyte. Americium-241 was more firmly fixed in the biomass of the aquatic moss. In 12 months, the biomass of the aquatic moss released about 30% of the initial americium activity into the water. To compare, the biomass of the pond weed released into the water medium up to 64% of the initial 241 Am activity in 1.5 4 months. The release rate was dependent on the decomposition rate of the plant biomass. The experiments showed that submerged macrophyte of the Yenisei River can accumulate considerable activities of 241 Am and retain americium for long periods of time in biomass. (author)

  9. Physics of plutonium and americium recycling in PWR using advanced fuel concepts

    International Nuclear Information System (INIS)

    Hourcade, E.

    2004-01-01

    PWR waste inventory management is considered in many countries including Frances as one of the main current issues. Pu and Am are the 2 main contents both in term of volume and long term radio-toxicity. Waiting for the Generation IV systems implementation (2035-2050), one of the mid-term solutions for their transmutation involves the use of advanced fuels in Pressurized Water Reactors (PWR). These have to require as little modification as possible of the core internals, the cooling system and fuel cycle facilities (fabrication and reprocessing). The first part of this paper deals with some neutronic characteristics of Pu and/or Am recycling. In a second part, 2 technical solutions MOX-HMR and APA-DUPLEX-84 are presented and the third part is devoted to the study of a few global strategies. The main neutronic parameters to be considered for Pu and Am recycling in PWR are void coefficient, Doppler coefficient, fraction of delayed neutrons and power distribution (especially for heterogeneous configurations). The modification of the moderation ratio, the opportunity to use inert matrices (targets), the optimisation of Uranium, Plutonium and Americium contents are the key parameters to play with. One of the solutions (APA-DUPLEX-84) presented here is a heterogeneous assembly with regular moderation ratio composed with both target fuel rods (Pu and Am embedded in an inert matrix) and standard UO 2 fuel rods. An EPR (European Pressurised Reactor) type reactor, loaded only with assemblies containing 84 peripheral targets, can reach an Americium consumption rate of (4.4; 23 kg/TWh) depending on the assembly concept. For Pu and Am inventories stabilisation, the theoretical fraction of reactors loaded with Pu + Am or Pu assemblies is about 60%. For Americium inventory stabilisation, the fraction decreases down to 16%, but Pu is produced at a rate of 18.5 Kg/TWh (-25% compared to one through UOX cycle)

  10. Separation of americium and plutonium from nuclear wastes by the TRUEX process

    International Nuclear Information System (INIS)

    Leonard, R.A.; Vandegrift, G.F.; Manry, C.W.

    1986-01-01

    Americium and plutonium can be removed from a transuranic (TRU) waste stream to <10 nCi/g by the TRUEX process. The resulting waste is nontransuranic, greatly reducing disposal costs. An overview is given of the TRUEX process and of centrifugal contactors used to implement this process. Then, a plan for the deployment of TRUEX at the Hanford Site is discussed. Finally, details are given on the proposed use of TRUEX to treat the liquid wastes from the Plutonium Finishing Plant at the Hanford Site

  11. Comparison of acid leachate and fusion methods to determine plutonium and americium in environmental samples

    International Nuclear Information System (INIS)

    Smith, L.L.; Markun, F.; TenKate, T.

    1992-06-01

    The Analytical Chemistry Laboratory at Argonne National Laboratory performs radiochemical analyses for a wide variety of sites within the Department of Energy complex. Since the chemical history of the samples may vary drastically from site to site, the effectiveness of any analytical technique may also vary. This study compares a potassium fluoride-pyrosulfate fusion technique with an acid leachate method. Both normal and high-fired soils and vegetation samples were analyzed for both americium and plutonium. Results show both methods work well, except for plutonium in high-fired soils. Here the fusion method provides higher accuracy

  12. Standardization of a method to study the distribution of Americium in purex process

    International Nuclear Information System (INIS)

    Dapolikar, T.T.; Pant, D.K.; Kapur, H.N.; Kumar, Rajendra; Dubey, K.

    2017-01-01

    In the present work the distribution of Americium in PUREX process is investigated in various process streams. For this purpose a method has been standardized for the determination of Am in process samples. The method involves extraction of Am with associated actinides using 30% TRPO-NPH at 0.3M HNO 3 followed by selective stripping of Am from the organic phase into aqueous phase at 6M HNO 3 . The assay of aqueous phase for Am content is carried out by alpha radiometry. The investigation has revealed that 100% Am follows the HLLW route. (author)

  13. Microstructure and elemental distribution of americium containing MOX fuel under the short term irradiation tests

    International Nuclear Information System (INIS)

    Tanaka, Kosuke; Hirosawa, Takashi; Obayashi, Hiroshi; Koyama, Shin Ichi; Yoshimochi, Hiroshi; Tanaka, Kenya

    2008-01-01

    In order to investigate the effect of americium addition to MOX fuels on the irradiation behavior, the 'Am-1' program is being conducted in JAEA. The Am-1 program consists of two short term irradiation tests of 10-minute and 24 hour irradiations and a steady-state irradiation test. The short-term irradiation tests were successfully completed and the post irradiation examinations (PIEs) are in progress. The PIEs for Am-containing MOX fuels focused on the microstructural evolution and redistribution behavior of Am at the initial stage of irradiation and the results to date are reported

  14. Recovery of Americium-241 from lightning rod by the method of chemical treatment

    International Nuclear Information System (INIS)

    Cruz, W.H.

    2013-01-01

    About 95% of the lightning rods installed in the Peruvian territory have set in their structures, pose small amounts of radioactive sources such as Americium-241 ( 241 Am), fewer and Radium 226 ( 226 Ra) these are alpha emitters and have a half life of 432 years and 1600 years respectively. In this paper describes the recovery of radioactive sources of 241 Am radioactive lightning rods using the conventional chemical treatment method using agents and acids to break down the slides. The 241 Am recovered was as excitation source and alpha particle generator for analysing samples by X Ray Fluorescence, for fixing the stainless steel 241 Am technique was used electrodeposition. (author)

  15. Distribution coefficients for plutonium and americium on particulates in aquatic environments

    International Nuclear Information System (INIS)

    Sanchez, A.L.; Schell, W.R.; Sibley, T.H.

    1982-01-01

    The distribution coefficients of two transuranic elements, plutonium and americium, were measured experimentally in laboratory systems of selected freshwater, estuarine, and marine environments. Gamma-ray emitting isotopes of these radionuclides, 237 Pu and 241 Am, were significantly greater than the sorption Ksub(d) values, suggesting some irreversibility in the sorption of these radionuclides onto sediments. The effects of pH and of sediment concentration on the distribution coefficients were also investigated. There were significant changes in the Ksub(d) values as these parameters were varied. Experiments using sterilized and nonsterilized samples for some of the sediment/water systems indicate possible bacterial effects on Ksub(d) values. (author)

  16. Recovery of americium from slag and crucible wastes and its purification

    International Nuclear Information System (INIS)

    Michael, K.M.; Dabholkar, G.M.; Vijayan, K.; Ramamoorthy, N.; Narayanan, C.V.; Jambunathan, U.; Kapoor, S.C.

    1990-01-01

    A method of recovery and purification of americium-241 from slag waste streams is described. Extraction of Am from slag solution of 0.16 M HNO 3 was carried out by tri-n-butyl phosphate. After stripping with acetic acid, Am was precipitated at pH 1. This was followed by metathesis to remove Ca. Final separation of Pu from Am solution was achieved by anion exchange method using Dowex 1x4 anion exchange resin. Details of large scale recovery of Am from slag are also described. (author). 12 refs., 11 tabs., 1 fig

  17. Study of the extraction and the purification of americium and trivalent actinides contained in effluents with supported liquid membranes

    International Nuclear Information System (INIS)

    Guillou, P.

    1990-12-01

    The supported liquid membrane technique is studied and developed for americium recovery from uranium or plutonium matrices and decontamination of liquid radioactive wastes. First tests on uranium-nickel solutions with a flat membrane showed the easiness of the operation and the efficiency of the process. Acid-resistant (10 N), interchangeable elements with hollow fibers, are developed and also a computerized automatic device. The different tests on americium solutions demonstrate the feasibility and the reliability of the system. Influence of various parameters on transfer kinetics is investigated

  18. Production of a square geometry Americium standard source for use with photodiodes

    Energy Technology Data Exchange (ETDEWEB)

    Costa, Priscila; Geraldo, Bianca; Raele, Marcus P.; Marumo, Júlio T.; Vicente, Roberto; Zahn, Guilherme S.; Genezini, Frederico A., E-mail: priscila3.costa@usp.br, E-mail: fredzini@ipen.br [Instituto de Pesquisas Energéticas e Nucleares (IPEN/CNEN-SP), São Paulo, SP (Brazil)

    2017-07-01

    In the development of a thermal neutron detector using a square photodiode and a thin boron film, a radioactive calibration source with the same geometry was needed. An americium-243 standard source was produced by electrodeposition aiming at the calibration of a PIN-type silicon photodiode with a detection area of 10 x 10 mm{sup 2}. To produce the samples two tests were performed. In the first test, a square stainless steel plate (10 x 10 mm{sup 2}) was fixed on the surface of the conventional plate, which was removed after deposition. To reduce the loss of activity of the source, in the second test nail polish was applied on the silver plate leaving only an area of 10 x 10 mm{sup 2} without varnish coating. Once the electrodeposition process was completed, the activity concentration measurement was performed by alpha particle spectrometry. The first method presented a lower activity when compared to the total activity of Am-243 added initially. For the second method, the total activity was concentrate in the exposed square region (without nail polish). The results showed that it is possible to obtain a square geometry source; furthermore, the surrounding nail polish was not contaminated by {sup 243}Am. The comparison of these two approaches indicated that the second method was more efficient as it was possible to concentrate all the americium activity in the delimited square area. (author)

  19. Application of extraction chromatography to the recovery of neptunium, plutonium and americium from an industrial waste

    International Nuclear Information System (INIS)

    Madic, C.; Kertesz, C.; Sontag, R.; Koehly, G.

    1980-01-01

    A pilot scale investigation was made to evaluate the possible application of the extraction chromatographic method (LLC) to the partitioning of alpha emitters from liquid wastes containing traces of transuranium elements. A secondary purpose was to obtain pure Am0 2 , which is used to produce alpha, gamma, and neutron sources. The process developed for alpha partitioning consists essentially of the extraction of macro amounts of uranium with 30% TBP in dodecane in mixer-settlers, then coextraction of Np-237, Pu-239, and Am-241 by LLC on a macro column filled with di-n-hexyl-octoxy-methyl-phosphine oxide (POX.11) adsorbed on an inert support. In each run about 200 liters of initial waste are decontaminated of alpha emitters. The loading step is followed by selective elution of americium, neptunium, and plutonium. The americium eluate is then subjected to the following operations: (1) separation of Am from Fe and Cd by LLC on a TBP column and (2) separation of Am from lanthanide traces by LLC on an HD(DiBM)P column after oxidation of Am(III) to Am(VI). The Am in the eluate is subsequently reduced to Am(III) and precipitated as oxalate with oxalic acid. The oxalate is then filtered and calcined to yield pure AmO 2

  20. Fuel cycle covariance of plutonium and americium separations to repository capacity using information theoretic measures

    International Nuclear Information System (INIS)

    Scopatz, Anthony; Schneider, Erich; Li, Jun; Yim, Man-Sung

    2011-01-01

    A light water reactor, fast reactor symbiotic fuel cycle scenario was modeled and parameterized based on thirty independent inputs. Simultaneously and stochastically choosing different values for each of these inputs and performing the associated fuel cycle mass-balance calculation, the fuel cycle itself underwent Monte Carlo simulation. A novel information theoretic metric is postulated as a measure of system-wide covariance. This metric is the coefficient of variation of the set of uncertainty coefficients generated from 2D slices of a 3D contingency table. It is then applied to the fuel cycle, taking fast reactor used fuel plutonium and americium separations as independent variables and the capacity of a fully-loaded tuff repository as the response. This set of parameters is known from prior studies to have a strong covariance. When measured with all 435 other input parameters possible, the fast reactor plutonium and americium separations pair was found to be ranked the second most covariant. This verifies that the coefficient of variation metric captures the desired sensitivity of sensitivity effects in the nuclear fuel cycle. (author)

  1. Contribution to the prediction of americium, plutonium and neptunium behaviour in the geosphere: chemical data

    International Nuclear Information System (INIS)

    Robouch, P.

    1989-01-01

    An exhaustive bibliographic review on hydrolysis of americium gives the stability constants, at zero ionic strength. No evidence of Am(OH) 4 - formation was found by solubility studies up to pH 2 (CO 3 ) 3 characterised by its X-ray diffraction pattern is studied at a high ionic strength. All the published results on Am in carbonate media are reinterpreted using these stability constants (Am-OH-CO 3 complexes are not needed). No evidence of Am(CO 3 ) 4 5- formation was found by spectrophotometry up to 3M. Literature results are used to determine the formal redox potentials at pH = 9.4 and to calculate the formation constants, at zero ionic strength. The formation of complexes between americium and humic materials (purified fulvic and humic acids) has been studied by a spectrophotometric technique. The results are interpreted by the formation of a 1:1 complexe. Solubility of the solid PuO 2 (CO 3 ) is measured in bicarbonate media at high ionic strength, to obtain the solubility product and formation constants of the PuO 2 (CO 3 ) i 2-2i complexes [fr

  2. Vitrification of F-area americium/curium: feasibility study and preliminary process recommendation

    International Nuclear Information System (INIS)

    Ramsey, W.G.; Miller, D.; Minichan, R.; Coleman, L.; Schumacher, R.; Hardy, B.; Jones, R.

    1994-01-01

    Work was performed to identify a process to vitrify the contents of F- canyon Tank 17.1. Tank 17.1 contains the majority of americium (Am) and curium (Cm) contained in the DOE Complex. Oak Ridge National Laboratory (ORNL) has made a formal request for this material as fuel for production of Cf252 and other transplutonium actinides. The Am and Cm (and associated lanthanide fission products) are currently in nitric acid solution. Transportation of the intensely radioactive Am/Cm in liquid form is not considered possible. As a result, the material will either be solidified and shipped to ORNL or discarded to the Tank Farm. Nuclear Materials Processing Technology (NMPT), therefore, requested Defense Waste Processing Technology (DWPT) to determine if the Tank 17.1 material could be vitrified, and if it was vitrified could the americium and curium be successfully recovered. Research was performed to determine if the Tank 17.1 contents could indeed be mixed with glass formers and vitrified. Additional studies identified critical process parameters such as heat loading, melter requirements, off-gas evolution, etc. Discussions with NMPT personnel were initiated to determine existing facilities where this work could be accomplished safely. A process has been identified which will convert the Am/Cm material into approximately 300kg of glass

  3. A simple approach to determine the diffusivity of americium in granite

    International Nuclear Information System (INIS)

    Song, L.; Feng, X.; Liang, J.; Zhang, Y.; Wang, J.

    2009-01-01

    The diffusivities of the key radionuclides in host rock are important for the performance assessment of repositories. One of the conventional methods for determining the diffusivities of radionuclides is to grind the rock tablet layer by layer and then to measure the radioactivity remaining on the rock tablet before each grinding cycle. Since grinding hard rock samples, especially those with radioactivity, is very difficult, we developed a new approach to determine the diffusivity of americium in granite. The new approach mainly includes two parts: one is to measure the radioactivities from both sides of a rock disk sample by autoradiography with phosphor imaging technique; the other is to study the relationship between the radioactivities and the apparent diffusivity of americium in granite by computer modelling. Because the high contamination risk of grinding radioactive rock samples has been avoided, the new approach is much simpler than the conventional method. It may be a better choice of measuring the diffusivities of radionuclides in rock, especially for those laboratories in which grinding radioactive rock samples is inconvenient. (orig.)

  4. Measurements of α-emitting plutonium and americium in the intertidal sands of west Cumbria, UK

    International Nuclear Information System (INIS)

    Eakins, J.D.; Morgan, A.; Baston, G.M.N.; Pratley, F.W.; Strange, L.P.; Burton, P.J.

    1990-01-01

    Samples of surface sand and sand cores were collected from intertidal regions of west Cumbria between Silloth and Walney Island (including the Duddon Estuary) between 1982 and 1984 and analysed for 238 Pu, 239+240 Pu and 241 Am. Generally, more than 95% of the α-emitting transuranic nuclides were associated with the sand and less than 5% with entrained silt. The greatest concentrations of both plutonium and americium were found at Braystones. Concentrations declined with distance from the Sellafield Works. The largest actinide deposits occurred at Drigg (320 and 720 kBq m -2 of 239+240 Pu and 241 Am respectively). The integrated deposits in intertidal sand between Silloth and Walney Island were about 4.2 and 7.0 TBq respectively, which represent about 1% of the total α-emitting activity discharged to sea from Sellafield Works up to 1982. The corresponding value for the Duddon Estuary is about 0.3%. Only on beaches close to Sellafield did levels of man-made α-emitters exceed those of natural α-emitting nuclides. The radiological consequences of the intertidal inventory of plutonium and americium are shown to be very small and much less than from the seafood pathway. (author)

  5. Measurements of. alpha. -emitting plutonium and americium in the intertidal sands of west Cumbria, UK

    Energy Technology Data Exchange (ETDEWEB)

    Eakins, J.D.; Morgan, A.; Baston, G.M.N.; Pratley, F.W.; Strange, L.P.; Burton, P.J. (UKAEA Harwell Lab. (UK). Environmental and Medical Science Div.)

    1990-01-01

    Samples of surface sand and sand cores were collected from intertidal regions of west Cumbria between Silloth and Walney Island (including the Duddon Estuary) between 1982 and 1984 and analysed for {sup 238}Pu, {sup 239+240}Pu and {sup 241}Am. Generally, more than 95% of the {alpha}-emitting transuranic nuclides were associated with the sand and less than 5% with entrained silt. The greatest concentrations of both plutonium and americium were found at Braystones. Concentrations declined with distance from the Sellafield Works. The largest actinide deposits occurred at Drigg (320 and 720 kBq m{sup -2} of {sup 239+240}Pu and {sup 241}Am respectively). The integrated deposits in intertidal sand between Silloth and Walney Island were about 4.2 and 7.0 TBq respectively, which represent about 1% of the total {alpha}-emitting activity discharged to sea from Sellafield Works up to 1982. The corresponding value for the Duddon Estuary is about 0.3%. Only on beaches close to Sellafield did levels of man-made {alpha}-emitters exceed those of natural {alpha}-emitting nuclides. The radiological consequences of the intertidal inventory of plutonium and americium are shown to be very small and much less than from the seafood pathway. (author).

  6. Transmutation of americium and curium incorporated in zirconia-based host materials

    Energy Technology Data Exchange (ETDEWEB)

    Raison, P.E. [CEA Cadarache, 13 - Saint-Paul-lez-Durance (France). Dept. d' Etudes des Combustibles; Haire, R.G. [Oak Ridge National Lab., TN (United States)

    2001-07-01

    Presented are studies involving the incorporation of americium and curium in zirconia-based materials. First explored was the pseudo ternary system AmO{sub 2}-ZrO{sub 2}-Y{sub 2}O{sub 3}. It was determined that selected Y-CSZ materials can incorporate significant quantities of americium oxide and remain cubic single-phase. The cell parameters of these fluorite-type products were established to be linear with the AmO{sub 2} content. The Cm{sub 2}O{sub 3}-ZrO{sub 2} system was also investigated. It was found that at 25 mol% of CmO{sub 1.5}, the Cm(III) stabilized zirconia in its cubic form (a = 5.21 {+-}0.01 Angstrom). At higher and lower concentrations, diphasic materials were encountered. At 50 mol% of CmO{sub 1.5}, a pyrochlore oxide - Cm{sub 2}Zr{sub 2}O{sub 7} - is formed (a = 10.63 {+-}0.02 Angstrom). (author)

  7. Comparison of Americium-Beryllium neutron spectrum obtained using activation foil detectors and NE-213 spectrometer

    International Nuclear Information System (INIS)

    Sunny, Sunil; Subbaiah, K.V.; Selvakumaran, T.S.

    1999-01-01

    Neutron spectrum of Americium - Beryllium (α,n) source is measured with two different spectrometers vis-a-vis activation foils (foil detectors) and NE-213 organic scintillator. Activity induced in the foils is measured with 4π-β-γ sodium iodide detector by integrating counts under photo peak and the saturation activity is found by correcting to elapsed time before counting. The data on calculated activity is fed into the unfolding code, SAND-II to obtain neutron spectrum. In the case of organic scintillator, the pulse height spectrum is obtained using MCA and this is processed with unfolding code DUST in order to get neutron spectrum. The Americium - Beryllium (α,n) neutron spectrum thus obtained by two different methods is compared. It is inferred that the NE-213 scintillator spectrum is in excellent agreement with the values beyond 1MeV. Neutron spectrum obtained by activation foils depends on initial guess spectrum and is found to be in reasonable agreement with NE-213 spectrum. (author)

  8. The construction of TRIGA-TRAP and direct high-precision Penning trap mass measurements on rare-earth elements and americium

    Energy Technology Data Exchange (ETDEWEB)

    Ketelaer, Jens

    2010-06-14

    The construction of TRIGA-TRAP and direct high-precision Penning trap mass measurements on rare-earth elements and americium: Nuclear masses are an important quantity to study nuclear structure since they reflect the sum of all nucleonic interactions. Many experimental possibilities exist to precisely measure masses, out of which the Penning trap is the tool to reach the highest precision. Moreover, absolute mass measurements can be performed using carbon, the atomic-mass standard, as a reference. The new double-Penning trap mass spectrometer TRIGA-TRAP has been installed and commissioned within this thesis work, which is the very first experimental setup of this kind located at a nuclear reactor. New technical developments have been carried out such as a reliable non-resonant laser ablation ion source for the production of carbon cluster ions and are still continued, like a non-destructive ion detection technique for single-ion measurements. Neutron-rich fission products will be available by the reactor that are important for nuclear astrophysics, especially the r-process. Prior to the on-line coupling to the reactor, TRIGA-TRAP already performed off-line mass measurements on stable and long-lived isotopes and will continue this program. The main focus within this thesis was on certain rare-earth nuclides in the well-established region of deformation around N {proportional_to} 90. Another field of interest are mass measurements on actinoids to test mass models and to provide direct links to the mass standard. Within this thesis, the mass of {sup 241}Am could be measured directly for the first time. (orig.)

  9. The construction of TRIGA-TRAP and direct high-precision Penning trap mass measurements on rare-earth elements and americium

    International Nuclear Information System (INIS)

    Ketelaer, Jens

    2010-01-01

    The construction of TRIGA-TRAP and direct high-precision Penning trap mass measurements on rare-earth elements and americium: Nuclear masses are an important quantity to study nuclear structure since they reflect the sum of all nucleonic interactions. Many experimental possibilities exist to precisely measure masses, out of which the Penning trap is the tool to reach the highest precision. Moreover, absolute mass measurements can be performed using carbon, the atomic-mass standard, as a reference. The new double-Penning trap mass spectrometer TRIGA-TRAP has been installed and commissioned within this thesis work, which is the very first experimental setup of this kind located at a nuclear reactor. New technical developments have been carried out such as a reliable non-resonant laser ablation ion source for the production of carbon cluster ions and are still continued, like a non-destructive ion detection technique for single-ion measurements. Neutron-rich fission products will be available by the reactor that are important for nuclear astrophysics, especially the r-process. Prior to the on-line coupling to the reactor, TRIGA-TRAP already performed off-line mass measurements on stable and long-lived isotopes and will continue this program. The main focus within this thesis was on certain rare-earth nuclides in the well-established region of deformation around N ∝ 90. Another field of interest are mass measurements on actinoids to test mass models and to provide direct links to the mass standard. Within this thesis, the mass of 241 Am could be measured directly for the first time. (orig.)

  10. EURADOS intercomparison on measurements and Monte Carlo modelling for the assessment of Americium in a USTUR leg phantom

    International Nuclear Information System (INIS)

    Lopez, M. A.; Broggio, D.; Capello, K.; Cardenas-Mendez, E.; El-Faramawy, N.; Franck, D.; James, A. C.; Kramer, G. H.; Lacerenza, G.; Lynch, T. P.; Navarro, J. F.; Navarro, T.; Perez, B.; Ruehm, W.; Tolmachev, S. Y.; Weitzenegger, E.

    2011-01-01

    A collaboration of the EURADOS working group on 'Internal Dosimetry' and the United States Transuranium and Uranium Registries (USTUR) has taken place to carry out an intercomparison on measurements and Monte Carlo modelling determining americium deposited in the bone of a USTUR leg phantom. Preliminary results and conclusions of this intercomparison exercise are presented here. (authors)

  11. The distribution of plutonium-239 and americium-241 in the Syrian hamster following its intravenous administration as citrate

    International Nuclear Information System (INIS)

    Rodwell, P.; Stather, J.W.

    1978-01-01

    Actinide distribution in various tissues and the skeleton of hamsters by liquid scintillation counting or isotope dilution. For plutonium 57% of activity was concentrated in the skeleton and more than 90% in the liver and skeleton after seven days. For americium the liver retained more than 50% of total activity and 25% was excreted in urine within seven days. (U.K.)

  12. The weak acid resin process: a dustless conversion route for the synthesis of americium bearing-blanket precursors

    International Nuclear Information System (INIS)

    Picart, S.; Gauthe, A.; Parant, P.; Remy, E.; Jobelin, I.; Pomared, J.M.; Grangaud, P.; Dauby, J.; Delahaye, T.; Caisso, M.; Bataille, M.; Bayle, J.P.; Frost, C.; Delage, C.; Martin, C.L.; Ayral, E.

    2016-01-01

    Mixed uranium-americium oxides are one of the materials envisaged for Americium Bearing Blankets dedicated to transmutation in fast neutron reactors. Conversion and fabrication processes are currently developed to make those materials in the form of dense and homogeneous oxide ceramic pellets or dense granulates incorporating uranium and americium. Their development points out the need of a simplified and optimized process which could lower hazards linked to dust generation of highly contaminating and irradiating compounds and facilitate material transfer in remote handling operations. This reason motivated the development of innovative 'dustless' route such as the Weak Acid Resin route (WAR) which provides the oxide precursors in the form of sub-millimeter-sized microspheres with optimal flowability and limits dust generation during conversion and fabrication steps. This study is thus devoted to the synthesis of mixed uranium-americium oxide microspheres by the WAR process and to the characterization of such precursors. This work also deals with their application to the fabrication of dense or porous pellets and with their potential use as dense spherules to make Sphere-Pac fuel. (authors)

  13. On the influence of the americium isotopic vector on the cooling time of minor actinides bearing blankets in fast reactors

    Directory of Open Access Journals (Sweden)

    Kooyman Timothée

    2018-01-01

    Full Text Available In the heterogeneous minor actinides transmutation approach, the nuclei to be transmuted are loaded in dedicated targets often located at the core periphery, so that long-lived heavy nuclides are turned into shorter-lived fission products by fission. To compensate for low flux level at the core periphery, the minor actinides content in the targets is set relatively high (around 20 at.%, which has a negative impact on the reprocessing of the targets due to their important decay heat level. After a complete analysis of the main contributors to the heat load of the irradiated targets, it is shown here that the choice of the reprocessing order of the various feeds of americium from the fuel cycle depends on the actual limit for fuel reprocessing. If reprocessing of hot targets is possible, it is more interesting to reprocess first the americium feed with a high 243Am content in order to limit the total cooling time of the targets, while if reprocessing of targets is limited by their decay heat, it is more interesting to wait for an increase in the 241Am content before loading the americium in the core. An optimization of the reprocessing order appears to lead to a decrease of the total cooling time by 15 years compared to a situation where all the americium feeds are mixed together when two feeds from SFR are considered with a high reprocessing limit.

  14. The weak acid resin process: a dustless conversion route for the synthesis of americium bearing-blanket precursors

    Energy Technology Data Exchange (ETDEWEB)

    Picart, S.; Gauthe, A.; Parant, P.; Remy, E.; Jobelin, I.; Pomared, J.M.; Grangaud, P.; Dauby, J.; Delahaye, T. [CEA, Centre de Marcoule, DEN/MAR/DRCP, F-30207 Bagnols-sur-Ceze (France); Caisso, M.; Bataille, M.; Bayle, J.P. [CEA, Centre de Marcoule, DEN/MAR/DTEC, F-30207 Bagnols-sur-Ceze (France); Frost, C. [CEA, Centre de Marcoule, DEN/MAR/DRCP, F-30207 Bagnols-sur-Ceze (France); Institut Europeen des Membranes, CNRS-ENSCM-UM, CC47, University of Montpellier, F-34095 Montpellier (France); Delage, C. [CEA, Centre de Cadarache, DEN/CAD/DEC, Saint-Paul-lez-Durance (France); Martin, C.L. [Univ. Grenoble Alpes, CNRS, SIMAP, F-38000 Grenoble (France); Ayral, E. [Institut Europeen des Membranes, CNRS-ENSCM-UM, CC47, University of Montpellier, F-34095 Montpellier (France)

    2016-07-01

    Mixed uranium-americium oxides are one of the materials envisaged for Americium Bearing Blankets dedicated to transmutation in fast neutron reactors. Conversion and fabrication processes are currently developed to make those materials in the form of dense and homogeneous oxide ceramic pellets or dense granulates incorporating uranium and americium. Their development points out the need of a simplified and optimized process which could lower hazards linked to dust generation of highly contaminating and irradiating compounds and facilitate material transfer in remote handling operations. This reason motivated the development of innovative 'dustless' route such as the Weak Acid Resin route (WAR) which provides the oxide precursors in the form of sub-millimeter-sized microspheres with optimal flowability and limits dust generation during conversion and fabrication steps. This study is thus devoted to the synthesis of mixed uranium-americium oxide microspheres by the WAR process and to the characterization of such precursors. This work also deals with their application to the fabrication of dense or porous pellets and with their potential use as dense spherules to make Sphere-Pac fuel. (authors)

  15. Worldwide bioassay data resources for plutonium/americium internal dosimetry studies

    International Nuclear Information System (INIS)

    Miller, G.; Bertelli, L.; Little, T.; Guilmette, R.; Riddell, T.; Filipy, R.

    2005-01-01

    Full text: Biokinetic models are the scientific underpinning of internal dosimetry. These models describe how materials of interest taken into the body by various routes (for example inhalation) are transported through the body, allowing the modelling of bioassay measurements and the estimation of radiation dose. The International Commission on Radiation Protection (ICRP) publishes biokinetic models for use in internal dosimetry. These models represent the consensus judgement of a committee of experts, based on human and animal data. Nonetheless, it is important to validate biokinetic models using directly applicable data, in a scientifically transparent manner, especially for internal dosimetry research purposes (as opposed to radiation protection), as in epidemiology studies. Two major goals would be to determine individual variations of model parameters for the purpose of assessing this source of uncertainty in internal dose calculations, and to determine values of workplace specific parameters (such as particle solubility in lung fluids) for different representative workplaces. Furthermore, data on the observed frequency of intakes under various conditions can be used in the interpretation of bioassay data. All of the above may be couched in the terminology of Bayesian statistical analysis and amount to the determination of the Bayesian prior probability distributions needed in a Bayesian interpretation of bioassay data. The authors have direct knowledge of several significant databases of plutonium/americium bioassay data (including autopsy data). The purpose of this paper is to acquaint the worldwide community with these resources and to invite others who may know of other such databases to participate with us in a publication that would document the content, form, and the procedures for seeking access to these databases. These databases represent a tremendous scientific resource in this field. Examples of databases known to the authors include: the

  16. XRD monitoring of α self-irradiation in uranium-americium mixed oxides.

    Science.gov (United States)

    Horlait, Denis; Lebreton, Florent; Roussel, Pascal; Delahaye, Thibaud

    2013-12-16

    The structural evolution under (241)Am self-irradiation of U(1-x)Am(x)O(2±δ) transmutation fuels (with x ≤ 0.5) was studied by X-ray diffraction (XRD). Samples first underwent a preliminary heat treatment performed under a reducing atmosphere (Ar/H2(4%)) aiming to recover the previously accumulated structural defects. Over all measurements (carried out over up to a full year and for integrated doses up to 1.5 × 10(18) α-decay events·g(-1)), only fluorite U(1-x)Am(x)O(2±δ) solid solutions were observed. Within a few days after the end of the heat treatment, each of the five studied samples was slowly oxidized as a consequence of their move to air atmosphere, which is evidenced by XRD by an initial sharp decrease of the unit cell parameter. For the compounds with x ≤ 0.15, this oxidation occurred without any phase transitions, but for U0.6Am0.4O(2±δ) and U0.5Am0.5O(2±δ), this process is accompanied by a transition from a first fluorite solid solution to a second oxidized one, as the latter is thermodynamically stable in ambient conditions. In the meantime and after the oxidation process, (241)Am α self-irradiation caused a structural swelling up to ∼0.8 vol %, independently of the sample composition. The kinetic constants of swelling were also determined by regression of experimental data and are, as expected, dependent on x and thus on the dose rate. The normalization of these kinetic constants by sample α-activity, however, leads to very close swelling rates among the samples. Finally, evolutions of microstrain and crystallite size were also monitored, but for the considered dose rates and cumulated doses, α self-irradiation was found, within the limits of the diffractometer used, to have almost no impact on these characteristics. Microstrain was found to be influenced instead by the americium content in the materials (i.e., by the impurities associated with americium starting material and the increase of cationic charge heterogeneity with

  17. Investigation of the separation of americium(III) and europium(III) by high-speed countercurrent chromatography

    International Nuclear Information System (INIS)

    Wu, J.F.; Jin, Y.R.; Xu, Q.C.; Wang, S.L.; Zhang, L.X.

    2005-01-01

    The long-lived actinides are the important elements in the radioactive waste ;disposal. Because the ions semi diameter and chemical properties of trivalent actinides(III) and trivalent lanthanides(III) are very similar, the separation between them is very difficult. Yang Yu-Sheng put forward the actinides(III) are softer acid than the lanthanides(III), so the actinides(III) are more easily extracted by the soft extractant contain sulfur or nitrogen than the lanthanides(III). Some research have been done on the separation between actinides(III) and lanthanides(III) using the extractants contain sulfur or nitrogen. The results show that satisfactory separation efficiency was gained. Countercurrent Chromatography (CCC) have many specific advantages, such as free from solid support, permit large sample volume and high flow rate, which is useful in the preconcentration of inorganic solute and inorganic preparation. Some studies were done on the separation of lanthanides or-other inorganic elements by HSCCC, the high-purity reagents prepared by HSCCC or CPC turned out to be successful. In present paper, the investigation of separation between Americium (III) and Euricium (III) by High-Speed Countercurrent Chromatography (HSCCC) were made. The extractant used in the work was prepared by ourselves, which is of the soft extractant contrain sulfur. The effects of separation condition on the separation efficiency of Am and Eu by HSCCC were investigated using dichlorophenyl dithiophosphinic acid in xylene as the stationary phase and 0.1 mol/L NaClO4 as mobile phase, respectively. The results show that mutual separation between Am and Eu can be accomplished. The separation factor increases with the increasing of the concentration of extractant and the pH value of the mobile phase, further more, minishing the flow rate of the mobile phase can also improves the separation efficiency between Am and Eu. The nearly base separation was gained when the flow rate is 0.35 ml/min, the

  18. The uptake of plutonium-239, 240, americium-241, strontium-90 into plants

    International Nuclear Information System (INIS)

    Popplewell, D.S.; Ham, G.J.; Johnson, T.E.

    1984-01-01

    This report describes the results of measurements on the uptake of plutonium, americium, strontium-90 and caesium-137 into peas, beet, oats, sweet corn, tomatoes and vegetable marrow grown in tubs containing radioactively-contaminated silts. The silts had been taken from an area of West Cumbria commonly referred to as the Ravenglass estuary. The experiments are categorised as being carried out under non-standard conditions because of the manner in which the radioactivity came to be incorporated into the growth medium. The growth medium was representative of conditions which could arise when the estuarine silt moves inland under the influence of wind and tide and mixes with the adjacent farm land. The silt had been contaminated by radioactive effluents from the nuclear fuels reprocessing plant at Sellafield and this contamination had been brought about by natural means. (Auth.)

  19. Comparative study of plutonium and americium bioaccumulation from two marine sediments contaminated in the natural environment

    International Nuclear Information System (INIS)

    Hamilton, T.F.; Smith, J.D.

    1991-01-01

    Plutonium and americium sediment-animal transfer was studied under controlled laboratory conditions by exposure of the benthic polychaete Nereis diversicolor (O. F. Mueller) to marine sediments contaminated by a nuclear bomb accident (near Thule, Greenland) and nuclear weapons testing (Enewetak Atoll). In both sediment regimes, the bioavailability of plutonium and 241 Am was low, with specific activity in the tissues 241 Am occurred and 241 Am uptake from the Thule sediment was enhanced compared to that from lagoon sediments of Enewetak Atoll. Autoradiography studies indicated the presence of hot particles of plutonium in the sediments. The results highlight the importance of purging animals of their gut contents in order to obtain accurate estimates of transuranic transfer from ingested sediments into tissue. It is further suggested that enhanced transuranic uptake by some benthic species could arise from ingestion of highly activity particles and organic-rich detritus present in the sediments. (author)

  20. Transportability Class of Americium in K Basin Sludge under Ambient and Hydrothermal Processing Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Delegard, Calvin H.; Schmitt, Bruce E.; Schmidt, Andrew J.

    2006-08-01

    This report establishes the technical bases for using a ''slow uptake'' instead of a ''moderate uptake'' transportability class for americium-241 (241Am) for the K Basin Sludge Treatment Project (STP) dose consequence analysis. Slow uptake classes are used for most uranium and plutonium oxides. A moderate uptake class has been used in prior STP analyses for 241Am based on the properties of separated 241Am and its associated oxide. However, when 241Am exists as an ingrown progeny (and as a small mass fraction) within plutonium mixtures, it is appropriate to assign transportability factors of the predominant plutonium mixtures (typically slow) to the Am241. It is argued that the transportability factor for 241Am in sludge likewise should be slow because it exists as a small mass fraction as the ingrown progeny within the uranium oxide in sludge. In this report, the transportability class assignment for 241Am is underpinned with radiochemical characterization data on K Basin sludge and with studies conducted with other irradiated fuel exposed to elevated temperatures and conditions similar to the STP. Key findings and conclusions from evaluation of the characterization data and published literature are summarized here. Plutonium and 241Am make up very small fractions of the uranium within the K Basin sludge matrix. Plutonium is present at about 1 atom per 500 atoms of uranium and 241Am at about 1 atom per 19000 of uranium. Plutonium and americium are found to remain with uranium in the solid phase in all of the {approx}60 samples taken and analyzed from various sources of K Basin sludge. The uranium-specific concentrations of plutonium and americium also remain approximately constant over a uranium concentration range (in the dry sludge solids) from 0.2 to 94 wt%, a factor of {approx}460. This invariability demonstrates that 241Am does not partition from the uranium or plutonium fraction for any characterized sludge matrix. Most

  1. Plutonium and americium concentrations and vertical profiles in some Italian mosses used as bioindicators

    International Nuclear Information System (INIS)

    Testa, C.; Desideri, D.; Meli, M.A.; Guerra, F.; Degetto, S.; Jia, G.; Gerdol, R.

    1998-01-01

    We have examined the uptake of actinide elements Am and Pu by different species of lichen and moss collected in two locations (Urbino, Central Italy; Alps region, North-east Italy). Plutonium and americium were separated and determined by extraction chromatography, electrodeposition and alpha-spectrometry. This paper summarizes our results with a special emphasis on the vertical profiles of these actinides in two different species of mosses. Several 1-2 cm depth sections were obtained and dated by 210 Pb method. A typical peak for 239,240 Pu and 241 Am was found in the very old moss species ('Sphagnum Compactum') at a depth corresponding to the period 1960-1970 which was the period characterized by the maximum nuclear weapon tests. In a younger moss species ('Neckeria Crispa') no peak was observed and the regression curves showed that Am is more mobile than 239,240 Pu and 238 Pu. (author)

  2. EURADOS action for determination of americium in skull measures in vivo and Monte Carlo simulation

    International Nuclear Information System (INIS)

    Lopez Ponte, M. A.; Navarro Amaro, J. F.; Perez Lopez, B.; Navarro Bravo, T.; Nogueira, P.; Vrba, T.

    2013-01-01

    From the Group of WG7 internal dosimetry of the EURADOS Organization (European Radiation Dosimetry group, e.V.) which It coordinates CIEMAT, international action for the vivo measurement of americium has been conducted in three mannequins type skull with detectors of Germanium by gamma spectrometry and simulation by Monte Carlo methods. Such action has been raised as two separate exercises, with the participation of institutions in Europe, America and Asia. Other actions similar precede this vivo intercomparison of measurement and modeling Monte Carlo1. The preliminary results and associated findings are presented in this work. The laboratory of the body radioactivity (CRC) of service counter of dosimetry staff internal (DPI) of the CIEMAT, it has been one of the participants in vivo measures exercise. On the other hand part, the Group of numerical dosimetry of CIEMAT is participant of the Monte Carlo2 simulation exercise. (Author)

  3. Complex formation of trivalent americium with salicylic acid at very low concentrations

    International Nuclear Information System (INIS)

    Melanie Mueller; Margret Acker; Steffen Taut; Gert Bernhard; Forschungszentrum Dresden-Rossendorf, Dresden

    2010-01-01

    For the first time, the complexation of americium(III) with salicylic acid was studied at trace metal concentrations using a 2.0 m Long Path Flow Cell for UV-vis spectroscopy. The detection limit of Am(III) in aqueous solution at pH 3.0 was found to be 5 x 10 -9 M. Two Am(III)-salicylate complexes were formed at pH 5.0 in 0.1 M NaClO 4 , indicated by a clear red shift of the absorption maximum. The absorption spectra obtained from spectrophotometric titration were analyzed by means of factor analysis and complex stabilities were calculated to be log β 110 = 2.56 ± 0.08 and log β 120 = 3.93 ± 0.19. (author)

  4. Recovery of plutonium and americium from chloride salt wastes by solvent extraction

    International Nuclear Information System (INIS)

    Reichley-Yinger, L.; Vandegrift, G.F.

    1987-01-01

    Plutonium and americium can be recovered from aqueous waste solutions containing a mixture of HCl and chloride salt wastes by the coupling of two solvent extraction systems: tributyl phosphate (TBP) in tetrachloroethylene (TCE) and octyl(phenyl)-N,N-diisobutylcarbamoylmethylphosphine oxide (CMPO) in TCE. In the flowsheet developed, the salt wastes are dissolved in HCl, the Pu(III) is oxidized to the IV state with NaClO 2 and recovered in the TBP-TCE cycle, and the Am is then removed from the resultant raffinate by the CMPO-TCE cycle. The consequences of the feed solution composition and extraction behavior of these species on the process flowsheet design, the Pu-product purity, and the decontamination of the aqueous raffinate from transuranic elements are discussed. 16 refs., 6 figs

  5. Americium-241 in surface soil associated with the Hanford site and vicinity

    International Nuclear Information System (INIS)

    Price, K.R.; Gilbert, R.O.; Gano, K.A.

    1981-05-01

    Various kinds of surface soil samples were collected and analyzed for Americium-241 ( 241 Am) to examine the feasibility of improving soil sample data for the Hanford Surface Environmental Surveillance Program. Results do not indicate that a major improvement would occur if procedures were changed from the current practices. Conclusions from this study are somewhat tempered by the very low levels of 241 Am ( 241 Am in soil crust (0 to 1.0 cm deep) was greater than the corresponding subsurface layer (1.0 to 2.5 cm deep), and the average concentration of 241 Am in some onsite samples collected near the PUREX facility was greater than comparable samples collected 60 km upwind at an offsite location

  6. Separation and measurement of thorium, plutonium, americium, uranium and strontium in environmental matrices

    International Nuclear Information System (INIS)

    Harrison, Jennifer J.; Zawadzki, Atun; Chisari, Robert; Wong, Henri K.Y.

    2011-01-01

    A technique for the isolation of thorium (Th), plutonium (Pu), americium (Am), uranium (U) and strontium (Sr) isotopes from various environmental matrices has been adapted from a previously published method specific to water samples (). Separation and isolation of the various elemental fractions from a single sub-sample is possible, thereby eliminating the need for multiple analyses. The technique involves sample dissolution, concentration via calcium phosphate co-precipitation, rapid column extraction using TEVA TM , TRU TM and Sr-Spec TM resin cartridges, alpha spectrometry for Th, Pu, U and Am and Cerenkov counting for Sr. Various standard reference materials were analysed and chemical yields are in the range of 70-80% for Th, Am, U and Sr and 50-60% for Pu. Sample sizes of up to 10 L for water, 5 g for dry soil and sediment and 10 g for dry vegetation and seaweed can be processed using this technique.

  7. Separation and measurement of thorium, plutonium, americium, uranium and strontium in environmental matrices

    Energy Technology Data Exchange (ETDEWEB)

    Harrison, Jennifer J., E-mail: jennifer.harrison@ansto.gov.au [Australian Nuclear Science and Technology Organisation, PMB 1, Menai NSW 2234 (Australia); Zawadzki, Atun; Chisari, Robert; Wong, Henri K.Y. [Australian Nuclear Science and Technology Organisation, PMB 1, Menai NSW 2234 (Australia)

    2011-10-15

    A technique for the isolation of thorium (Th), plutonium (Pu), americium (Am), uranium (U) and strontium (Sr) isotopes from various environmental matrices has been adapted from a previously published method specific to water samples (). Separation and isolation of the various elemental fractions from a single sub-sample is possible, thereby eliminating the need for multiple analyses. The technique involves sample dissolution, concentration via calcium phosphate co-precipitation, rapid column extraction using TEVA{sup TM}, TRU{sup TM} and Sr-Spec{sup TM} resin cartridges, alpha spectrometry for Th, Pu, U and Am and Cerenkov counting for Sr. Various standard reference materials were analysed and chemical yields are in the range of 70-80% for Th, Am, U and Sr and 50-60% for Pu. Sample sizes of up to 10 L for water, 5 g for dry soil and sediment and 10 g for dry vegetation and seaweed can be processed using this technique.

  8. Liquid-liquid extraction of plutonium and americium by cekanoic acid from alkaline medium

    International Nuclear Information System (INIS)

    Venugopal Chetty, K.; Sagar, V.; Swarup, R.

    2001-01-01

    Liquid-liquid extraction studies of plutonium and americium from aqueous carbonate medium using a high molecular weight carboxylic acid namely cekanoic acid in different diluents has been carried out. The distribution ratio (D) values for Pu(IV) and Am(III) under various parameters such as concentration of extractant, Na 2 CO 3 and initial pH were obtained. Results indicated that Pu(IV) and Am(III) could be satisfactorily extracted together or individually from aqueous carbonate medium using cekanoic acid in different diluents like carbon tetrachloride, cyclohexane, toluene, n-dodecane or solvesso-100. The D values for Pu(IV) and Am(III) also indicated the possibility of their mutual separation. The back extraction of Pu and Am with different reagents was also studied. (orig.)

  9. Magnesium ionophore II as an extraction agent for trivalent europium and americium

    Energy Technology Data Exchange (ETDEWEB)

    Makrlik, Emanuel [Czech Univ. of Life Sciences, Prague (Czech Republic). Faculty of Environmental Sciences; Vanura, Petr [Univ. of Chemistry and Technology, Prague (Czech Republic). Dept. of Analytical Chemistry

    2016-11-01

    Solvent extraction of microamounts of trivalent europium and americium into nitrobenzene by using a mixture of hydrogen dicarbollylcobaltate (H{sup +}B{sup -}) and magnesium ionophore II (L) was studied. The equilibrium data were explained assuming that the species HL{sup +}, HL{sup +}{sub 2}, ML{sup 3+}{sub 2}, and ML{sup 3+}{sub 3} (M{sup 3+} = Eu{sup 3+}, Am{sup 3+}; L=magnesium, ionophore II) are extracted into the nitrobenzene phase. Extraction and stability constants of the cationic complex species in nitrobenzene saturated with water were determined and discussed. From the experimental results it is evident that this effective magnesium ionophore II receptor for the Eu{sup 3+} and Am{sup 3+} cations could be considered as a potential extraction agent for nuclear waste treatment.

  10. Experimental and in situ investigations on americium, curium and plutonium behaviour in marine benthic species: transfer from water or sediments

    International Nuclear Information System (INIS)

    Miramand, P.

    1984-06-01

    The tranfer of transuranic elements -americium, curium and plutonium- from the sediments containing them to some marine benthic species (endofauna and epifauna) was studied with a twofold approach - laboratory and in-situ investigation. The experimental investigations, divided into three parts, made it possible to specify concentration factors (F.C.), transfer factors (F.T.) and to understand the process involved for 5 benthic species. The result were refined by an in-situ study that brought new data on the marine distribution of the transuranic elements released by the La Hague plant. Finally, the localization of americium and plutonium in the tissues and cells of these species was determined by autoradiography [fr

  11. Annual report for FY 1976 on project AN0115A: the migration of plutonium and americium in the lithosphere

    International Nuclear Information System (INIS)

    Fried, S.; Friedman, A.M.; Hines, J.J.; Atcher, R.W.; Quarterman, L.A.; Volesky, A.

    1976-12-01

    Studies have been carried out on the migration of plutonium and americium in solutions flowing through porous and crushed rock and through fissures. The migration process can be described in terms of the surface absorption of these elements. In addition, chemical effects on the absorption have been observed. One of these effects is possibly due to the presence of a plutonium polymer that migrates at a more rapid rate than normal plutonium

  12. Upper limits to americium concentration in large sized sodium-cooled fast reactors loaded with metallic fuel

    International Nuclear Information System (INIS)

    Zhang, Youpeng; Wallenius, Janne

    2014-01-01

    Highlights: • The americium transmutation capability of Integral Fast Reactor was investigated. • The impact from americium introduction was parameterized by applying SERPENT Monte Carlo calculations. • Higher americium content in metallic fuel leads to a power penalty, preserving consistent safety margins. - Abstract: Transient analysis of a large sized sodium-cooled reactor loaded with metallic fuel modified by different fractions of americium have been performed. Unprotected loss-of-offsite power, unprotected loss-of-flow and unprotected transient-over-power accidents were simulated with the SAS4A/SASSYS code based on the geometrical model of an IFR with power rating of 2500 MW th , using safety parameters obtained with the SERPENT Monte Carlo code. The Ti-modified austenitic D9 steel, having higher creep rupture strength, was considered as the cladding and structural material apart from the ferritic/martensitic HT9 steel. For the reference case of U–12Pu–1Am–10Zr fuel at EOEC, the margin to fuel melt during a design basis condition UTOP is about 50 K for a maximum linear rating of 30 kW/m. In order to maintain a margin of 50 K to fuel failure, the linear power rating has to be reduced by ∼3% and 6% for 2 wt.% and 3 wt.% Am introduction into the fuel respectively. Hence, an Am concentration of 2–3 wt.% in the fuel would lead to a power penalty of 3–6%, permitting a consumption rate of 3.0–5.1 kg Am/TW h th . This consumption rate is significantly higher than the one previously obtained for oxide fuelled SFRs

  13. The behaviour under irradiation of molybdenum matrix for inert matrix fuel containing americium oxide (CerMet concept)

    Energy Technology Data Exchange (ETDEWEB)

    D' Agata, E., E-mail: elio.dagata@ec.europa.eu [European Commission, Joint Research Centre, Institute for Energy and Transport, P.O. Box 2, 1755 ZG Petten (Netherlands); Knol, S.; Fedorov, A.V. [Nuclear Research and Consultancy Group, P.O. Box 25, 1755 ZG Petten (Netherlands); Fernandez, A.; Somers, J. [European Commission, Joint Research Centre, Institute for Transuranium Elements, P.O. Box 2340, 76125 Karlsruhe (Germany); Klaassen, F. [Nuclear Research and Consultancy Group, P.O. Box 25, 1755 ZG Petten (Netherlands)

    2015-10-15

    Americium is a strong contributor to the long term radiotoxicity of high activity nuclear waste. Transmutation by irradiation in nuclear reactors or Accelerator Driven System (ADS, subcritical reactors dedicated to transmutation) of long-lived nuclides like {sup 241}Am is therefore an option for the reduction of radiotoxicity of waste packages to be stored in a repository. In order to safely burn americium in a fast reactor or ADS, it must be incorporated in a matrix that could be metallic (CerMet target) or ceramic (CerCer target). One of the most promising matrix to incorporate Am is molybdenum. In order to address the issues (swelling, stability under irradiation, gas retention and release) of using Mo as matrix to transmute Am, two irradiation experiments have been conducted recently at the High Flux Reactor (HFR) in Petten (The Netherland) namely HELIOS and BODEX. The BODEX experiment is a separate effect test, where the molybdenum behaviour is studied without the presence of fission products using {sup 10}B to “produce” helium, the HELIOS experiment included a more representative fuel target with the presence of Am and fission product. This paper covers the results of Post Irradiation Examination (PIE) of the two irradiation experiments mentioned above where molybdenum behaviour has been deeply investigated as possible matrix to transmute americium (CerMet fuel target). The behaviour of molybdenum looks satisfying at operating temperature but at high temperature (above 1000 °C) more investigation should be performed.

  14. Consideration of the effect of lymph-node deposition upon the measurement of plutonium and americium in the lungs

    International Nuclear Information System (INIS)

    Falk, R.B.; Lagerquist, C.R.

    1975-01-01

    Measurement of an inhaled radionuclide by external photon counting includes quantities which may be contained in lymph nodes, as well as quantities in the lungs. An overestimate of the lung burden can result, if a portion of the radionuclide were present in the lymph nodes. This problem is analyzed with respect to the measurement of inhaled plutonium containing plutonium-241 and americium-241, when americium-241 has been used as a tracer for the plutonium. Equations are derived which yield the amounts of americium and of plutonium in the lungs and in the lymph nodes as a function of time after exposure and for various translocation and retention parameters. Count histories (count profiles) of actual exposure cases are compared with calculated count profiles in order to gain insight into possible values of the translocation and retention parameters. Comparison is also made with calculated count profiles using values of translocation and retention parameters recommended by the International Commission on Radiological Protection (ICRP) for use with the Task Group Lung Model. The magnitude of the possible overestimate (error factor) was calculated for combinations o []parameters which yielded matches to the observed count histories. (auth)

  15. Uptake of americium-241 by plants from contaminated Chernobyl exclusive zone test site soils

    International Nuclear Information System (INIS)

    Rashydov, N.M.

    2002-01-01

    Americium-241 was found to accumulate in soils and biological objects of the environment. Its concentration has increased many times after the Chernobyl disaster and can be expected to increase about 40 times in the future. This research concentrated on the contaminated exclusive Chernobyl zone polluted by trace radionuclides, their behavior and accumulation by various plant species. Special attention is devoted to the bioavailability of 241 Am to the plants Galium rivale, G. tinctorium, G. aparine, G. intermedium, Berteroa incana, Artemisia absinthium, A. vulgaris, Centaurea borysthenica, C. arenaria, Cirsium arvense, Succissa pratensis, Solidago virgaurea, Linaria vulgaris, Lepidium ruderale, Stenactis annua, Veronica maxima, Verbascum lychnitis, Euphorbia cyparissias, Genista tinctoria, Erigeron canadensis, Oenothera biennis, Betula pendula and Quercus robur, which were collected from the Chernobyl, Kopachi, and Yanov districts. The plant samples of Oenothera biennis, Betula pendula and Quercus robur were collected from the Yanov district, where the soil contamination by 241 Am and 137 Cs was at the level of 660 and 27 MBq/m 2 , respectively. Gamma spectroscopy and radiochemical methods were used to estimate the activity concentration of 137 Cs, 90 Sr, 238 Pu, 239+240 Pu, 241 Am. The radionuclides were measured in the dry green mass of the plant samples and in the dry soils. The contamination of the Oenothera biennis, Betula pendula and Quercus robur samples by 137 Cs was (5.8±1,5)x10 6 , (7.4±1.1)x10 5 , and (2.6±0.2)x10 6 Bq/kg dry mass, respectively, and contamination by 241 Am was 47±5, 45±3 and 3.2±0.2 Bq/kg, respectively. The soil-to-plant transfer ratio for 137 Cs ranged lay within the interval of 0.2 to 0.03 Bq/kg : Bq/m 2 , the the transfer ratio for 241 Am did not exceed 7x10 -5 Bq/kg : Bq/m 2 . The coefficient of the relative contents of the 241 Am/ 239+240 Pu radionuclides in the various plant samples varied from 3.2 to 8.3, while for soil from

  16. Solution speciation of plutonium and Americium at an Australian legacy radioactive waste disposal site.

    Science.gov (United States)

    Ikeda-Ohno, Atsushi; Harrison, Jennifer J; Thiruvoth, Sangeeth; Wilsher, Kerry; Wong, Henri K Y; Johansen, Mathew P; Waite, T David; Payne, Timothy E

    2014-09-02

    During the 1960s, radioactive waste containing small amounts of plutonium (Pu) and americium (Am) was disposed in shallow trenches at the Little Forest Burial Ground (LFBG), located near the southern suburbs of Sydney, Australia. Because of periodic saturation and overflowing of the former disposal trenches, Pu and Am have been transferred from the buried wastes into the surrounding surface soils. The presence of readily detected amounts of Pu and Am in the trench waters provides a unique opportunity to study their aqueous speciation under environmentally relevant conditions. This study aims to comprehensively investigate the chemical speciation of Pu and Am in the trench water by combining fluoride coprecipitation, solvent extraction, particle size fractionation, and thermochemical modeling. The predominant oxidation states of dissolved Pu and Am species were found to be Pu(IV) and Am(III), and large proportions of both actinides (Pu, 97.7%; Am, 86.8%) were associated with mobile colloids in the submicron size range. On the basis of this information, possible management options are assessed.

  17. Cleanex process: a versatile solvent extraction process for recovery and purification of lanthanides, americium, and curium

    International Nuclear Information System (INIS)

    Bigelow, J.E.; Collins, E.D.; King, L.J.

    1979-01-01

    At a concentration of 1 M in straight-chain hydrocarbon diluent, HDEHP will extract americium, curium, and other trivalent actinide and lanthanide elements from dilute acid or salt solutions. The solute is back-extracted with more concentrated acid, either nitric or hydrochloric. The process has been used in the continuous, countercurrent mode, but its greatest advantage arises in batch extractions where the excess acid can be titrated with NaOH to produce a final acidity of about 0.03 M. Under these conditions, 99% recovery can be achieved, usually in one stage. Cleanex was used on the 50-liter scale at the Transuranium Processing Plant at Oak Ridge for 12 years to provide a broad spectrum cleanup to transuranium elements before applying more sophisticated techniques for separating individual products. The process is also used routinely to recover excessive losses of curium and/or californium from plant waste streams. The solvent system is relatively resistant to radiation damage, being usable up to 200 W-h/liter

  18. Study of biosorbents application on the treatment of radioactive liquid wastes with americium-241

    International Nuclear Information System (INIS)

    Borba, Tania Regina de

    2010-01-01

    The use of nuclear energy for many different purposes has been intensified and highlighted by the benefits that it provides. Medical diagnosis and therapy, agriculture, industry and electricity generation are examples of its application. However, nuclear energy generates radioactive wastes that require suitable treatment ensuring life and environmental safety. Biosorption and bioaccumulation represent an emergent alternative for the treatment of radioactive liquid wastes, providing volume reduction and physical state change. This work aimed to study biosorbents for the treatment of radioactive liquid wastes contaminated with americium-241 in order to reduce the volume and change the physical state from liquid to solid. The biosorbents evaluated were Saccharomyces cerevisiae immobilized in calcium alginate beads, inactivated and free cells of Saccharomyces cerevisiae, calcium alginate beads, Bacillus subtilis, Cupriavidus metallidurans and Ochrobactrum anthropi. The results were quite satisfactory, achieving 100% in some cases. The technique presented in this work may be useful and viable for implementing at the Waste Management Laboratory of IPEN - CNEN/SP in short term, since it is an easy and low cost method. (author)

  19. Experimental studies on the biokinetics of plutonium and americium in the cephalopod Octopus vulgaris

    International Nuclear Information System (INIS)

    Guary, J.C.; Fowler, S.W.

    1982-01-01

    Radiotracer experiments using the photon-emitters 237 Pu and 241 Am were performed to examine uptake, tissue distribution and retention of plutonium and americium in the cephalopod Octopus vulgaris Cuvier. A 2 wk exposure in contaminated sea water resulted in twice as much 237 Pu being taken up by whole octopus as 241 Am. Immediately following uptake approximately 41% and 73% of the 237 Pu and 241 Am respectively were located in the branchial hearts. Depuration rates for both radionuclides were identical; approximately 46% of both radionuclides initially incorporated were associated with a long-lived compartment which turned over very slowly (Tbsub(1/2) = 1.5 yr). Longer exposures to 241 Am resulted in an increase in the size of the slowly exchanging 241 Am pool in the octopus. After 2 mo depuration, the majority of the residual activity of both radionuclides was in the branchial hearts. On average 33% of the 241 Am ingested with food was assimilated into tissues, primarily the hepatopancreas. Different whole-body 241 Am excretion rates were observed at different times following assimilation and were related to transfer processes taking place within internal tissues, most notably between hepatopancreas and the branchial hearts. Relationships between circulatory and excretory functions of these 2 organs are discussed and a physiological mechanism is proposed to explain the observed patterns of 241 Am excretion in O. vulgaris. (orig.)

  20. Experimental studies on the biokinetics of plutonium and americium in the cephalopod Octopus vulgaris

    Energy Technology Data Exchange (ETDEWEB)

    Guary, J.C.; Fowler, S.W.

    1982-03-05

    Radiotracer experiments using the photon-emitters /sup 237/Pu and /sup 241/Am were performed to examine uptake, tissue distribution and retention of plutonium and americium in the cephalopod Octopus vulgaris Cuvier. A 2 wk exposure in contaminated sea water resulted in twice as much /sup 237/Pu being taken up by whole octopus as /sup 241/Am. Immediately following uptake approximately 41% and 73% of the /sup 237/Pu and /sup 241/Am respectively were located in the branchial hearts. Depuration rates for both radionuclides were identical; approximately 46% of both radionuclides initially incorporated were associated with a long-lived compartment which turned over very slowly (Tbsub(1/2) = 1.5 yr). Longer exposures to /sup 241/Am resulted in an increase in the size of the slowly exchanging /sup 241/Am pool in the octopus. After 2 mo depuration, the majority of the residual activity of both radionuclides was in the branchial hearts. On average 33% of the /sup 241/Am ingested with food was assimilated into tissues, primarily the hepatopancreas. Different whole-body /sup 241/Am excretion rates were observed at different times following assimilation and were related to transfer processes taking place within internal tissues, most notably between hepatopancreas and the branchial hearts. Relationships between circulatory and excretory functions of these 2 organs are discussed and a physiological mechanism is proposed to explain the observed patterns of /sup 241/Am excretion in O. vulgaris.

  1. Contrasts between the marine and freshwater biological interactions of plutonium and americium

    International Nuclear Information System (INIS)

    Livingston, H.D.; Bowen, V.T.

    1975-01-01

    Whether in lakes or the oceans the transuranic elements plutonium and americium are taken up by marine organisms, with concentration factors that would class them as nice, typical heavy metals. There is no evidence for strong, widespread discrimination against the transuranics by either plant or animal absorptive surfaces. In both freshwater and marine situations the major reservoir of Pu and Am soon becomes the sediments, and organisms are more exposed to uptake of these nuclides the closer is their ecological involvement with the sediments. Although there is little evidence that this can be an ionic strength effect, it does appear that Pu may be somewhat more available, biologically, in marine environments, and Am, conversely, in fresh water. We incline to the belief that details of these behaviors are usually controlled by local availability of organic complexers. No compelling evidence exists of increase in Pu concentration at higher levels of food chains; in marine situations this appears true of Am as well, but a few data suggest that in fresh water fish there is a progressive increase, in higher trophic levels, in the ratio Am to Pu. Although marine and fresh water biogeochemistries of transuranics are much more similar than we had expected, it will generally be dangerous to extrapolate from one to the other. In both systems there appears to us no question that we are observing real element biogeochemistry, not the redistribution of inert, labelled, fallout fragments

  2. Americium-241 use of measurement lead equivalent thickness for medical x-ray room: A review

    International Nuclear Information System (INIS)

    Mohd Khalid Matori; Husaini Saleh; Abd Aziz Mhd Ramli; Muhammad Jamal Md Isa; Mohd Firdaus Abd Rahman; Zainal Jamaluddin

    2010-01-01

    Lead equivalent thickness measurement of a shielding material in diagnostic radiology is very important to ensure that requirements for the purpose of radiation protection of patients, employees and the public are met. The Malaysian Ministry of Health (MOH) has established that the irradiation room must have sufficient shielding thickness, for example for general radiography it must be at least equal to 2.0 mm of Pb, for panoramic dental radiography at least equal to 1.5 mm of Pb and for mammography should be a minimum of 1.0 mm of Pb. This paper presents a technique using americium-241 source to test and verify the integrity of the shielding thickness in term of lead equivalent for X-ray room at health centres. Results of measurement of 30 irradiation rooms conducted from 2009 to mid 2010 were analyzed for this presentation. Technical comparison of the attenuation of gamma rays from Am-241 source through the walls of the irradiation room and pieces of lead were used to assess the lead equivalent thickness of the walls. Results showed that 96.7 % of the irradiation rooms tested meet the requirements of the Ministry of Health and is suitable for the installation of the intended diagnostic X-ray apparatus. Some specific positions such as door knobs and locks, electrical plug sockets were identified with potential to not met the required lead equivalent thickness hence may contribute to higher radiation exposure to workers and the public. (author)

  3. Speciation and bioavailability of Americium-241 in the fresh water environment

    International Nuclear Information System (INIS)

    Bierkens, J.

    1986-01-01

    Due to its anthropogenic origin, the transuranic americium 241 confronts physiologists with the intriguing question, which mechanisms are involved in the incorporation or elimination of such artificial elements in biological cycles. The investigations on the speciation and bioavailability of 241 Am in the freshwater environment aim to establish a relation between the behavior of 241 Am in freshwater ecosystems and its availability for biota. In the limnic environment, most often characterized by a high organic load and a low conductivity, the effect of complexation of 241 Am with humic acids and competition with trivalent cations such as A1 and Fe, were proven to be significant on the speciation of 241 Am. Based on the registration of the 241 Am uptake by a large number of freshwater organisms, the crayfish Astacus leptodactylus Eschscholtz was chosen to study the whole-body uptake of 241 Am, its corresponding organ distribution and its retention in the animal. The share of external fixation and ingestion in the global uptake, and the effect of speciation on it, were studied more carefully. Other aspects in this physiological part were: the kinetics of 241 Am in the hemolymph and the hepatopancreas, and its subcellular distribution in the digestive gland. Finally, by comparing the physiology of 241 Am with some other metals ( 240 Pu, 64 Cu, 198 Au) with analogous or contradictional properties, we tried to find out whether the behavior of 241 Am in organisms can be explained from its chemical characteristics

  4. Plutonium and americium recovery from spent molten-salt-extraction salts with aluminum-magnesium alloys

    International Nuclear Information System (INIS)

    Cusick, M.J.; Sherwood, W.G.; Fitzpatrick, R.F.

    1984-01-01

    Development work was performed to determine the feasibility of removing plutonium and americium from spent molten-salt-extraction (MSE) salts using Al-Mg alloys. If the product buttons from this process are compatible with subsequent aqueous processing, the complex chloride-to-nitrate aqueous conversion step which is presently required for these salts may be eliminated. The optimum alloy composition used to treat spent 8 wt % MSE salts in the past yielded poor phase-disengagement characteristics when applied to 30 mol % salts. After a limited investigation of other alloy compositions in the Al-Mg-Pu-Am system, it was determined that the Al-Pu-Am system could yield a compatible alloy. In this system, experiments were performed to investigate the effects of plutonium loading in the alloy, excess magnesium, age of the spent salt on actinide recovery, phase disengagement, and button homogeneity. Experimental results indicate that 95 percent plutonium recoveries can be attained for fresh salts. Further development is required for backlog salts generated prior to 1981. A homogeneous product alloy, as required for aqueous processing, could not be produced

  5. Preparation of curium-americium oxide microspheres by resin-bead loading

    International Nuclear Information System (INIS)

    Chattin, F.R.; Benker, D.E.; Lloyd, M.H.; Orr, P.B.; Ross, R.G.; Wiggins, J.T.

    1980-01-01

    Resin-bead loading and calcination techniques have been used to produce all curium and americium oxide feed material (about 2.2 kg) for HFIR targets since 1971. The process based on Dowex 50W resin has progressed from a series of test runs, through special production runs, into routine production in permanent equipment beginning in 1975. Key attributes of this process are its reliability, high yields, and ease of operation. The process is suited for remote operation in hot cells. Yields approaching 95% are routinely obtained and only one unacceptable product has been generated during routine production operations. There have been no problems in fabricating targets from this oxide or in the subsequent irradiation of these targets. The present scale of production of 150 to 250 g/y supplies the present need and is comparable with the level of other chemical process operations at TRU. Since the annual production is accomplished in two 8 to 12 day periods, there has been no reason to consider further scale-up. However, the rate of production could easily be doubled by simply adding a second set of calcination equipment

  6. Comparative study of plutonium and americium bioaccumulation from two marine sediments contaminated in the natural environment

    Energy Technology Data Exchange (ETDEWEB)

    Hamilton, T.F.; Smith, J.D. (Melbourne Univ., Parkville (Australia). Dept. of Inorganic Chemistry); Fowler, S.W.; LaRosa, J.; Holm, E. (International Atomic Energy Agency, Monaco-Ville (Monaco). Lab. of Marine Radioactivity); Aarkrog, A.; Dahlgaard, H. (Risoe National Lab., Roskilde (Denmark))

    1991-01-01

    Plutonium and americium sediment-animal transfer was studied under controlled laboratory conditions by exposure of the benthic polychaete Nereis diversicolor (O. F. Mueller) to marine sediments contaminated by a nuclear bomb accident (near Thule, Greenland) and nuclear weapons testing (Enewetak Atoll). In both sediment regimes, the bioavailability of plutonium and {sup 241}Am was low, with specific activity in the tissues <1% (dry wt) than in the sediments. Over the first three months, a slight preference in transfer of plutonium over {sup 241}Am occurred and {sup 241}Am uptake from the Thule sediment was enhanced compared to that from lagoon sediments of Enewetak Atoll. Autoradiography studies indicated the presence of hot particles of plutonium in the sediments. The results highlight the importance of purging animals of their gut contents in order to obtain accurate estimates of transuranic transfer from ingested sediments into tissue. It is further suggested that enhanced transuranic uptake by some benthic species could arise from ingestion of highly activity particles and organic-rich detritus present in the sediments. (author).

  7. Multicompartment kinetic models for the metabolism of americium, plutonium and uranium in rats

    International Nuclear Information System (INIS)

    Sontag, W.

    1986-01-01

    To examine the kinetic behaviour of americium, plutonium and uranium in male and female rats, an extended mammillary model has been developed, composed of 10 compartments connected with 17 linear transfer coefficients. The 10 compartments describe the behaviour of the three nuclides in the blood, skeleton, liver and kidney; the remaining activity is assigned to one residual organ. Each organ is divided into two compartments, short- and long-term. In the skeleton the short-term compartment has been assumed to be the bone surface and marrow, and the long-term compartment the deep bone; in the liver, evidence suggests that the short-term compartment is physiologically associated with lysosomes and the long-term compartment identical with telolysosomes. Influence of age, sex and different nuclides on the transfer coefficients and the absorbed radiation dose are discussed. By using the transfer coefficients calculated for intravenous injection, the behaviour of the nuclides in skeleton and liver during continuous intake has been calculated. The behaviour of the three nuclides in skeleton and liver after intravenous injection has also been calculated with the additional assumption that from the fifth day the animals were treated continuously with a chelating agent. (UK)

  8. Incorporation of plutonium, americium and curium into the Irish Sea seabed by biological activity

    Energy Technology Data Exchange (ETDEWEB)

    Kershaw, P J; Swift, D J; Pentreath, R J; Lovett, M B

    1984-12-01

    Bioturbation was considered as a potentially significant mechanism for the incorporation of long-lived radionuclides into the seabed and in particular the activities of a large echiuran Maximulleria lankesteri. Radionuclides of the transuranium elements plutonium, americium and cirium are discharged into the Irish Sea under authorization as part of the low-level liquid effluent from the British Nuclear Fuels plc reprocessing plant at Sellafield, Cumbria, England. The distribution of Pu-239, 240, Pu-238, Am-241, Cm-244 and Cm-242 concentrations and the Pu-239, 240/Pu-238 quotient in samples taken in April and May 1983 from the sediment surface, burrow linings, sediments adjacent to burrows, and the gut contents and body of a large M. lankesteri clearly indicate that bioturbation is responsible, at least in part, for the incorporation of these radionuclides to depths of up to 140 cm. This area of sediments represents a significant present-day sink, but the permanence of this sink and the likelihood that radioactivity will be remobilized and be returned to man, depends on a large number of factors. 15 references, 18 figures.

  9. Americium and plutonium in water, biota, and sediment from the central Oregon coast

    International Nuclear Information System (INIS)

    Nielsen, R.D.

    1982-06-01

    Plutonium-239, 240 and americium-241 were measured in the mussel Mytilus californianus from the region of Coos Bay, OR. The flesh of this species has a plutonium concentration of about 90 fCi/kg, and an Am-241/Pu-239, 240 ratio that is high relative to mixed fallout, ranging between two and three. Transuranic concentrations in sediment, unfiltered water, and filterable particulates were also measured; none of these materials has an Am/Pu ratio as greatly elevated as the mussels, and there is no apparent difference in the Am/Pu ratio of terrestrial runoff and coastal water. Sediment core profiles do not allow accumulation rates or depositional histories to be identified, but it does not appear that material characterized by a high Am/Pu ratio has ever been introduced to this estuary. Other bivalves (Tresus capax and Macoma nasuta) and a polychaete (Abarenicola sp.) do not have an elevated Am/Pu ratio, although the absolute activity of plutonium in the infaunal bivalves is roughly four times that in the mussels

  10. Assessment of radiation doses from residential smoke detectors that contain americium-241

    International Nuclear Information System (INIS)

    O'Donnell, F.R.; Etnier, E.L.; Holton, G.A.; Travis, C.C.

    1981-10-01

    External dose equivalents and internal dose commitments were estimated for individuals and populations from annual distribution, use, and disposal of 10 million ionization chamber smoke detectors that contain 110 kBq (3 μCi) americium-241 each. Under exposure scenarios developed for normal distribution, use, and disposal using the best available information, annual external dose equivalents to average individuals were estimated to range from 4 fSv (0.4 prem) to 20 nSv (2 μrem) for total body and from 7 fSv to 40 nSv for bone. Internal dose commitments to individuals under post disposal scenarios were estimated to range from 0.006 to 80 μSv (0.0006 to 8 mrem) to total body and from 0.06 to 800 μSv to bone. The total collective dose (the sum of external dose equivalents and 50-year internal dose commitments) for all individuals involved with distribution, use, or disposal of 10 million smoke detectors was estimated

  11. Structural study of U1-xAmxO2±δ oxide microspheres dedicated to the production of americium bearing blankets

    International Nuclear Information System (INIS)

    Caisso, Marie

    2016-01-01

    One of the studied routes to reduce nuclear waste amount, is, after plutonium recycling, americium (Am) heterogeneous transmutation in fast neutron reactors, through the generation of short-lives and inert elements. Am irradiation requires the fabrication of U 1-x Am x O 2±δ pellets and the CRMP (Calcined Resin Microsphere Pelletization) process is currently considered as one the most promising candidate among other fabrication routes. It is based, before pellet sintering, on the compaction of U 1-x Am x O 2±δ oxide microspheres, synthesized through the thermal conversion of ion exchange resin microspheres, loaded with UO 2 2+ and Am 3+ cations. Compared to standard methods using powder metallurgy, CRMP process favours pressing step (easy microsphere flow) while limiting generation of highly radioactive Am-based fine particles. In this context, this PhD work was focused on the exhaustive characterization of CRMP process different steps, from a mechanistic and structural point of view. The cation molecular complex used in the resin was thus determined, highlighting carboxylic bidentate ligand binding around U and Am elements. Thermal conversion was also in-situ followed, and the structures of the different synthesized compounds evidenced and accurately characterized, i.e. (U 1-x Am x ) 3 O 8 et U 1-x Am x O 2±δ . Am substitution in each of them was explained, revealing related distortions around U and Am cations. Finally, sintering of U 1-x Am x O 2±δ microspheres shaped into pellets was studied, showing a two-step densification. This unusual behavior corresponds to multi-scale reorganization into the material during sintering thermal treatment, associated to the presence of nanoparticles in the green pellet that sinter at low temperature. (author) [fr

  12. The extraction of lanthanides and americium by benzyldiakylamines and benzyltrialkylammonium nitrates from the nitrate solutions; structure and aggregation of their salts

    International Nuclear Information System (INIS)

    Jedinakova, V.; Zilkova, J.; Dvorak, Z.; Vojtiskova, M.

    1982-01-01

    Benzyldialkylamine and benzyltrialkylammonium nitrates were used for the extraction of lanthanides and americium from aqueous nitrate solutions. The dependence of the extraction performance for Ln(III) and Am(III) on the concentration of nitric acid, the kind and concentration of salting-out agents in the aqueous phase, and the kind of solvent were investigated. The extraction of Am(III) is compared with the extraction of lanthanides. The difference in distribution coefficients for lanthanides and americium can be utilized for the separation of lanthanides and americium. Using vapor phase osmometry and cryoscopy the association of these compounds was measured at 5.5deg, 25deg and 37deg C, allowing rough estimates of ΔH and ΔS for the formation of the aggregates, monomers in the case of benzyldiethylamine, benzyldibutylamine, benzyldihexylamine and benzyldioctylamine, tetramers for the benzyldibutylamine nitrate and tetramers for benzyldimethyldodecylammonium nitrate. (author)

  13. Sorption of plutonium and americium on repository, backfill and geological materials relevant to the JNFL low-level radioactive waste repository at Rokkasho-Mura

    International Nuclear Information System (INIS)

    Baston, G.M.N.; Berry, J.A.; Brownsword, M.; Heath, T.G.; Tweed, C.J.; Williams, S.J.

    1995-01-01

    An integrated program of batch sorption experiments and mathematical modeling has been carried out to study the sorption of plutonium and americium on a series of repository, backfill and geological materials relevant to the JNFL low-level radioactive waste repository at Rokkasho-Mura. The sorption of plutonium and americium on samples of concrete, mortar, sand/bentonite, tuff, sandstone and cover soil has been investigated. In addition, specimens of bitumen, cation and anion exchange resins, and polyester were chemically degraded. The resulting degradation product solutions, alongside solutions of humic and isosaccharinic acids were used to study the effects on plutonium sorption onto concrete, sand/bentonite and sandstone. The sorption behavior of plutonium and americium has been modeled using the geochemical speciation program HARPHRQ in conjunction with the HATCHES database

  14. SPHERE: Irradiation of sphere-pac fuel of UPuO2−x containing 3% Americium

    International Nuclear Information System (INIS)

    D’Agata, E.; Hania, P.R.; McGinley, J.; Somers, J.; Sciolla, C.; Baas, P.J.; Kamer, S.; Okel, R.A.F.; Bobeldijk, I.; Delage, F.; Bejaoui, S.

    2014-01-01

    Highlights: • SPHERE is designed to check the behaviour of MADF sphere-pac concept. • MADF sphere-pac are compared with MADF pellet. • Swelling, helium release and restructuring behaviour will be the main output of the experiment. • An experiment to check sphere-pac MABB fuel behaviour is now under design. - Abstract: Americium is a strong contributor to the long term radiotoxicity of high activity nuclear waste. Transmutation by irradiation in nuclear reactors of long-lived nuclides like 241 Am is therefore an option for the reduction of radiotoxicity of waste packages to be stored in a repository. The SPHERE irradiation experiment is the latest of a series of European experiments on americium transmutation (e.g. EFTTRA-T4, EFTTRA-T4bis, HELIOS, MARIOS) performed in the HFR (High Flux Reactor). The SPHERE experiment is carried out in the framework of the 4-year project FAIRFUELS of the EURATOM 7th Framework Programme (FP7). During the past years of experimental works in the field of transmutation and tests of innovative nuclear fuels, the release or trapping of helium as well as helium induced fuel swelling have been shown to be the key issues for the design of Am-bearing targets. The main objective of the SPHERE experiment is to study the in-pile behaviour of fuel containing 3% of americium and to compare the behaviour of sphere-pac fuel to pellet fuel, in particular the role of microstructure and temperature on fission gas release (mainly He) and on fuel swelling. The SPHERE experiment is being irradiated since September 2013 in the HFR in Petten (The Netherlands) and is expected to be terminated in spring 2015. The experiment has been designed to last up to 18 reactor cycles (corresponding to 18 months) but may reach its target earlier. This paper discusses the rationale and objective of the SPHERE experiment and provides a general description of its design

  15. Experiments comparing the uptake of americium from chloride media using extraction chromatography

    International Nuclear Information System (INIS)

    FitzPatrick, J.R.; Schake, B.S.; Schulte, L.D.; Martinez, B.T.; Salazar, R.R.

    1995-01-01

    Clean-up of actinide effluent waste steams is of increasing importance at the Los Alamos Plutonium Facility, TA-55, and removing the actinide elements to very low levels allows less radioactivity to go the Los Alamos National Laboratory Water Treatment Facility, TA-50, thus reducing the number of drums of TRU waste. Americium (Am) is a difficult element to remove from chloride media because the +3 state is difficult to oxidize and chelating resins work better with elements such as plutonium which are more readily oxidized to the +4 and/or +6 state. Currently in hydrochloric acid (HC1) media, the acidic liquid waste is neutralized with potassium hydroxide to precipitate the metal hydroxides, before disposal to TA-50. This process is not very efficient. The removal of Am from chloride media was compared using a series of resins, some commercial and some made in our laboratory, using different percentages by weight of octyl(phenyl)-N,N-diiso- butylcarbamoyl-methylphosphine oxide (CMPO ) along with diamyl amylphosphonate (DAAP) or tributyl phosphate (TBP) as diluents. Resins were also made with no added diluent. Early comparisons using small-scale contact studies with 0.5 grams of resin in 0.1M-12M HC1, and subsequent small-scale flow experiments show a trend in which Am uptake is proportional to the amount of CMPO on the resins and the diluent plays a minor role in the uptake of Am from these solutions. Redox chemistry effects were also investigated. From these studies, it is possible to determine the best conditions for the removal of Am from HC1 media thus reducing the gross alpha content of the waste stream by a factor of 10-100 which reduces the number of barrels of waste produced at the Water Treatment Facility

  16. Concentrations of plutonium and americium in plankton from the western Mediterranean Sea.

    Science.gov (United States)

    Sanchez-Cabeza, Joan-Albert; Merino, Juan; Masqué, Pere; Mitchell, Peter I; Vintró, L León; Schell, William R; Cross, Lluïsa; Calbet, Albert

    2003-07-20

    Understanding the transfer of radionuclides through the food chain leading to man and in particular, the uptake of transuranic nuclides by plankton, is basic to assess the potential radiological risk of the consumption of marine products by man. The main sources of transuranic elements in the Mediterranean Sea in the past were global fallout and the Palomares accident, although at present smaller amounts are released from nuclear establishments in the northwestern region. Plankton from the western Mediterranean Sea was collected and analyzed for plutonium and americium in order to study their biological uptake. The microplankton fractions accounted for approximately 50% of the total plutonium contents in particulate form. At Garrucha (Palomares area), microplankton showed much higher 239,240 Pu activity, indicating the contamination with plutonium from the bottom sediments. Concentration factors were within the range of the values recommended by the International Atomic Energy Agency. Continental shelf mesoplankton was observed to efficiently concentrate transuranics. In open seawaters, concentrations were much lower. We speculate that sediments might play a role in the transfer of transuranics to mesoplankton in coastal waters, although we cannot discard that the difference in species composition may also play a role. In Palomares, both 239,240 Pu and 241Am showed activities five times higher than the mean values observed in continental shelf mesoplankton. As the plutonium isotopic ratios in the contaminated sample were similar to those found in material related to the accident, the contamination was attributed to bomb debris from the Palomares accident. Concentration factors in mesoplankton were also in relatively good agreement with the ranges recommended by IAEA. In the Palomares station the highest concentration factor was observed in the sample that showed predominance of the dynoflagellate Ceratium spp. Mean values of the enrichment factors showed, on

  17. Concentration and vertical distribution of plutonium and americium in Italian mosses and lichens

    International Nuclear Information System (INIS)

    Jia, G.; Desideri, D.; Guerra, F.; Meli, M.A.; Testa, C.

    1997-01-01

    The plutonium and americium concentration and vertical distribution in some Italian mosses and lichens have been determined. The 239,240 Pu, 238 Pu and 241 Am concentration ranges in tree trunk lichens 0.83-1.87, 0.052-0.154 and 0.180-0.770 Bq/kg, respectively. The corresponding values in tree mosses are higher and more scattered ranging from 0.321 to 4.96, from 0.029 to 0.171 and from 0.200 to 1.93 Bq/kg. The mean 238 Pu/ 239,240 Pu and 241 Am/ 239,240 Pu ratios are 0.088±0.037 and 0.38 ± 0.13 in lichens and 0.091±0.072 and 0.54±0.16 in tree mosses. The Pu and Am concentrations are relatively low in terrestrial mosses. The 239,240 Pu, 238 Pu and 241 Am vertical distributions in a terrestrial moss core (Neckera Crispa) collected near Urbino (central Italy) show an exponential decrease with the height. On the contrary the 241 Am vertical distribution in another terrestrial moss core (Sphagnum Compactum) collected in the Alps (northern Italy) shows an interesting peak at 16 cm which corresponds to the deposition of fallout from the nuclear weapon tests in 1960's. The 241 Am movement upward and downward in the moss core is also studied. The results show once again that both mosses and lichens are very effective accumulators of Pu and Am and that they can be used as good biological indicators of the radionuclide airborne pollution from nuclear facilities and nuclear weapon tests. They can play a very important role in cycling naturally or artificially enhanced radionuclides in the atmosphere over long time scales. (author)

  18. A study of plutonium and americium concentrations in seaspray on the southern Scottish coast

    International Nuclear Information System (INIS)

    McKay, W.A.; Strange, L.; Walker, M.I.; Halliwell, C.M.

    1992-01-01

    Seaspray and seawater have been collected from the southern Scottish coast and, for comparison, Cumbria in northwest England during 1989 and 1991. The occurrence of sea-to-land transfer of the actinides plutonium and americium in seaspray was observed on these coasts using muslin screens (a semi-quantitative technique most efficient for collecting large spray droplets) and high volume conventional air samplers. The actinides and fine particulate in the spray were present in relatively higher concentrations than measured in the adjacent seawater, i.e. the spray was enriched in particulate actinides. The net efficiency of the muslim screens in collecting airborne plutonium isotopes and 241 Am generally appeared to be about 20%. A review of earlier published concentrations of 239+240 Pu and 241 Am measured in aerosol and deposition for over a year several tens of metres inland was carried out. This suggested that airborne activities are up to a factor of 5 times higher in Cumbria than southern Scotland. However, neither the new data collected in 1989 and 1991 nor this older data suggests any enhancement of seaspray actinide enrichment in southern Scotland compared to Cumbria. This finding contrasts with earlier, more limited, comparisons that have been carried out which suggested such a difference. There is clear evidence of considerable localised spatial and temporal variability in aerosol actinide enrichment over the beaches in both areas. Enrichments varies between 20 and 500 relative to the adjacent surf zone waters. However, the average enrichment in spray based on the continuous measurements made further inland is likely to be at the lower end of this range. (author)

  19. Behavior of americium, curium, and certain fission products in fluoride melts in the presence of s olid extraction agents

    International Nuclear Information System (INIS)

    Alekseev, V.A.; Klokman, V.R.; Morozova, Z.E.; Ziv, V.S.

    1986-01-01

    The authors consider the behavior of americium, curium, and certain fission products (europium, cerium, yttrium, and strontium) in fluoride and chlode-fluoride melts in the presence of nonisomorphous solid phases: calcium fluoride and lanthanum and zirconium oxides. It is shown that the trace components enter the solid calcium fluoride in a regular fashion only in the presence of an adequate amount of oxygen in the melt. The effect of oxygen on the coprecipitation with calcium fluoride occurs because oxygen compounds of the elements must be formed in the melt, and these are then coprecipitated with the calcium fluoride

  20. Theoretical investigation of pressure-induced structural transitions in americium using GGA+U and hybrid density functional theory methods

    DEFF Research Database (Denmark)

    Verma, Ashok K.; Modak, P.; Sharma, Surinder M.

    2013-01-01

    First-principles calculations have been performed for americium (Am) metal using the generalized gradient approximation + orbital-dependent onsite Coulomb repulsion via Hubbard interaction (GGA+U) and hybrid density functional theory (HYB-DFT) methods to investigate various ground state properties......-I to Am-II transition. Good agreement was found between calculated and experimental equations of states for all phases, but the first three phases need larger U (α) parameters (where α represents the fraction of Hartree-Fock exchange energy replacing the DFT exchange energy) than the fourth phase in order...

  1. Co-precipitation of plutonium(IV) and americium(III) from nitric acid-oxalic acid solutions with bismuth oxalate

    International Nuclear Information System (INIS)

    Pius, I.C.; Noronha, D.M.; Chaudhury, Satyajeet

    2017-01-01

    Co-precipitation of plutonium and americium from nitric acid-oxalic acid solutions with bismuth oxalate has been investigated for the removal of these long lived α-active nuclides from waste solutions. Effect of concentration of bismuth and oxalic acid on the co-precipitation of Pu(IV) from 3 M HNO_3 has been investigated. Similar experiments were also carried out from 3.75 M HNO_3 on co-precipitation of Am(III) to optimize the conditions of precipitation. Strong co-precipitation of Pu(IV) and Am(III) with bismuth oxalate indicate feasibility of treatment of plutonium and americium bearing waste solutions. (author)

  2. Use of radioanalytical methods for determination of uranium, neptunium, plutonium, americium and curium isotopes in radioactive wastes; Utilizacao de metodos radioanaliticos para a determinacao de isotopos de uranio, plutonio, americio e curio em rejeitos radioativos

    Energy Technology Data Exchange (ETDEWEB)

    Geraldo, Bianca

    2012-07-01

    Activated charcoal is a common type of radioactive waste that contains high concentrations of fission and activation products. The management of this waste includes its characterization aiming the determination and quantification of the specific radionuclides including those known as Difficult-to-Measure Radionuclides (RDM). The analysis of the RDM's generally involves complex radiochemical analysis for purification and separation of the radionuclides, which are expensive and time-consuming. The objective of this work was to define a methodology for sequential analysis of the isotopes of uranium, neptunium, plutonium, americium and curium present in a type of radioactive waste, evaluating chemical yield, analysis of time spent, amount of secondary waste generated and cost. Three methodologies were compared and validated that employ ion exchange (TI + EC), extraction chromatography (EC) and extraction with polymers (ECP). The waste chosen was the activated charcoal from the purification system of primary circuit water cooling the reactor IEA-R1. The charcoal samples were dissolved by acid digestion followed by purification and separation of isotopes with ion exchange resins, extraction and chromatographic extraction polymers. Isotopes were analyzed on an alpha spectrometer, equipped with surface barrier detectors. The chemical yields were satisfactory for the methods TI + EC and EC. ECP method was comparable with those methods only for uranium. Statistical analysis as well the analysis of time spent, amount of secondary waste generated and cost revealed that EC method is the most effective for identifying and quantifying U, Np, Pu, Am and Cm present in charcoal. (author)

  3. Extraction of trivalent actinides and lanthanides from nitric acid solutions by ion flotation

    International Nuclear Information System (INIS)

    Mezhov, E.H.; Samatov, A.V.; Troyanovskiy, L.V.

    1992-01-01

    To determine whether the deep extraction of trivalent actinides from liquid active waste is feasible, the authors made a detailed investigation into the ion flotation of europium (as a simulator of americium) and americium from nitric acid solutions by using as an SAS precipitant either lauril phosphoric acid (LPA) to reprocess 0.1-0.7 M HNO 3 or diphosphine dioxides (PO) for 1-5 M HNO 3 . In all instances the extent of metal removal increases with floto-reagent expenditure. When the floto-reagent excess required for full precipitation is reached, the extraction of the metals under study is high, viz., 97-98% from 0.1 M HNO 3 with LPA and ∼75% from 3-3.5 M HNO 3 with PO per one flotation operation

  4. Osteosarcoma induction by plutonium-239, americium-241 and neptunium-237 : the problem of deriving risk estimates for man

    International Nuclear Information System (INIS)

    Taylor, D.M.

    1988-01-01

    Spontaneous bone cancer (osteosarcoma) represents only about 0.3% of all human cancers, but is well known to be inducible in humans by internal contamination with radium-226 and radium-224. plutonium-239, americium-241 and neptunium-237 form, or will form, the principal long-lived alpha particle emitting components of high activity waste and burnt-up nuclear fuel elements. These three nuclides deposit extensively in human bone and although, fortunately, no case of a human osteosarcoma induced by any of these nuclides is known, evidence from animal studies suggests that all three are more effective than radium-226 in inducing osteosarcoma. The assumption that the ratio of the risk factors, the number of osteosarcoma expected per 10000 person/animal Gy, for radium-226 and any other bone-seeking alpha-emitter will be independent of animal species has formed the basis of all the important studies of the radiotoxicity of actinide nuclides in experimental animals. The aim of this communication is to review the risk factors which may be calculated from the various animal studies carried out over the last thirty years with plutonium-237, americium-241 and neptunium-237 and to consider the problems which may arise in extrapolating these risk factors to homo sapiens

  5. Temperature and concentration dependences of the electrical resistivity for alloys of plutonium with americium under normal conditions

    Science.gov (United States)

    Tsiovkin, Yu. Yu.; Povzner, A. A.; Tsiovkina, L. Yu.; Dremov, V. V.; Kabirova, L. R.; Dyachenko, A. A.; Bystrushkin, V. B.; Ryabukhina, M. V.; Lukoyanov, A. V.; Shorikov, A. O.

    2010-01-01

    The temperature and concentration dependences of the electrical resistivity for alloys of americium with plutonium are analyzed in terms of the multiband conductivity model for binary disordered substitution-type alloys. For the case of high temperatures ( T > ΘD, ΘD is the Debye temperature), a system of self-consistent equations of the coherent potential approximation has been derived for the scattering of conduction electrons by impurities and phonons without any constraints on the interaction intensity. The definitions of the shift and broadening operator for a single-electron level are used to show qualitatively and quantitatively that the pattern of the temperature dependence of the electrical resistivity for alloys is determined by the balance between the coherent and incoherent contributions to the electron-phonon scattering and that the interference conduction electron scattering mechanism can be the main cause of the negative temperature coefficient of resistivity observed in some alloys involving actinides. It is shown that the great values of the observed resistivity may be attributable to interband transitions of charge carriers and renormalization of their effective mass through strong s-d band hybridization. The concentration and temperature dependences of the resistivity for alloys of plutonium and americium calculated in terms of the derived conductivity model are compared with the available experimental data.

  6. Plutonium, americium, and uranium in blow-sand mounds of safety-shot sites at the Nevada Test Site and the Tonopah Test Range

    International Nuclear Information System (INIS)

    Essington, E.H.; Gilbert, R.O.; Wireman, D.L.; Brady, D.N.; Fowler, E.B.

    1977-01-01

    Blow-sand mounds or miniature sand dunes and mounds created by burrowing activities of animals were investigated by the Nevada Applied Ecology Group (NAEG) to determine the influence of mounds on plutonium, americium, and uranium distributions and inventories in areas of the Nevada Test Site and Tonopah Test Range. Those radioactive elements were added to the environment as a result of safety experiments of nuclear devices. Two studies were conducted. The first was to estimate the vertical distribution of americium in the blow-sand mounds and in the desert pavement surrounding the mounds. The second was to estimate the amount or concentration of the radioactive materials accumulated in the mound relative to the desert pavement. Five mound types were identified in which plutonium, americium, and uranium concentrations were measured: grass, shrub, complex, animal, and diffuse. The mount top (that portion above the surrounding land surface datum), the mound bottom (that portion below the mound to a depth of 5 cm below the surrounding land surface datum), and soil from the immediate area surrounding the mound were compared separately to determine if the radioactive elements had concentrated in the mounds. Results of the studies indicate that the mounds exhibit higher concentrations of plutonium, americium, and uranium than the immediate surrounding soil. The type of mound does not appear to have influenced the amount of the radioactive material found in the mound except for the animal mounds where the burrowing activities appear to have obliterated distribution patterns

  7. In situ characterization of uranium and americium oxide solid solution formation for CRMP process: first combination of in situ XRD and XANES measurements.

    Science.gov (United States)

    Caisso, Marie; Picart, Sébastien; Belin, Renaud C; Lebreton, Florent; Martin, Philippe M; Dardenne, Kathy; Rothe, Jörg; Neuville, Daniel R; Delahaye, Thibaud; Ayral, André

    2015-04-14

    Transmutation of americium in heterogeneous mode through the use of U1-xAmxO2±δ ceramic pellets, also known as Americium Bearing Blankets (AmBB), has become a major research axis. Nevertheless, in order to consider future large-scale deployment, the processes involved in AmBB fabrication have to minimize fine particle dissemination, due to the presence of americium, which considerably increases the risk of contamination. New synthesis routes avoiding the use of pulverulent precursors are thus currently under development, such as the Calcined Resin Microsphere Pelletization (CRMP) process. It is based on the use of weak-acid resin (WAR) microspheres as precursors, loaded with actinide cations. After two specific calcinations under controlled atmospheres, resin microspheres are converted into oxide microspheres composed of a monophasic U1-xAmxO2±δ phase. Understanding the different mechanisms during thermal conversion, that lead to the release of organic matter and the formation of a solid solution, appear essential. By combining in situ techniques such as XRD and XAS, it has become possible to identify the key temperatures for oxide formation, and the corresponding oxidation states taken by uranium and americium during mineralization. This paper thus presents the first results on the mineralization of (U,Am) loaded resin microspheres into a solid solution, through in situ XAS analysis correlated with HT-XRD.

  8. Chemical behaviour of trivalent and pentavalent americium in saline NaCl-solutions. Studies of transferability of laboratory data to natural conditions. Interim report. Reported period: 1.2.1993-31.12.1993; Chemisches Verhalten von drei- und fuenfwertigem Americium in Salinen NaCl-Loesungen. Untersuchung der Uebertragbarkeit von Labordaten auf natuerliche Verhaeltnisse. Zwischenbericht. Berichtszeitraum 1.2.1993-31.12.1993

    Energy Technology Data Exchange (ETDEWEB)

    Runde, W; Kim, J I

    1994-09-15

    In order to clarify the chemical behaviour of Americium in saline aqueous systems relevant for final storage this study deals with the chemical reactions of trivalent and pentavalent Americium in NaCl-solutions under the influence of radiolysis from its own alpha radiation. The focus of the study was on investigating the geologically relevant reactions, such as hydrolysis or carbonate- and chloride complexing in solid-liquid equilibriums. Comprehensive measurements on solubility and spectroscopic studies in NaCl-solutions were carried out in a CO{sub 2}-free atmosphere and 10{sup -2} atm CO{sub 2} partial pressure. Identification and characterisation of the AM (III) and AM(V) solid phases were supplemented by structural research with the chemically analogue EU (III) and Np(V) compounds. The alpha-radiation induced radiolysis in saline NaCl solutions and the redox behaviour of Americium which was influenced thereby were spectroscopically quantified. (orig.) [Deutsch] Zur Klaerung des chemischen Verhaltens von Americium in endlagerrelevanten salinen aquatischen Systemen befasst sich die vorliegende Arbeit mit den chemischen Reaktionen des drei- und fuenfwertigen Americiums in NaCl-Loesungen unter dem Einfluss der Radiolyse durch die eigene {alpha}-Strahlung. Der Schwerpunkt dieser Arbeit lag auf der Untersuchung der geologisch relevanten Reaktionen, wie Hydrolyse sowie Carbonat- und Chloridkomplexierung in fest-fluessig Gleichgewichtssystemen. Hierzu wurden umfassende Loeslichkeitsmessungen und spektroskopische Untersuchungen in NaCl-Loesungen, sowohl unter CO{sub 2}-freier Atmosphaere als auch unter 10{sup -2} atm CO{sub 2}-Partialdruck, durchgefuehrt. Die Identifizierung und Charakterisierung der Am(III)- und Am(V)-Festphasen wurde ergaenzt durch strukturelle Untersuchungen mit den chemisch analogen Eu(III)- und Np(V)-Verbindungen. Die von der {alpha}-Strahlung induzierte Radiolyse in salinen NaCl-Loesungen und das dadurch beeinflusste Redoxverhalten von Americium

  9. Novel Americium Treatment Process for Surface Water and Dust Suppression Water

    International Nuclear Information System (INIS)

    Tiepel, E.W.; Pigeon, P.; Nesta, S.; Anderson, J.

    2006-01-01

    The Rocky Flats Environmental Technology Site (RFETS), a former nuclear weapons production plant, has been remediated under CERCLA and decommissioned to become a National Wildlife Refuge. The site conducted this cleanup effort under the Rocky Flats Cleanup Agreement (RFCA) that established limits for the discharge of surface and process waters from the site. At the end of 2004, while a number of process buildings were undergoing decommissioning, routine monitoring of a discharge pond (Pond A-4) containing approximately 28 million gallons of water was discovered to have been contaminated with a trace amount of Americium-241 (Am-241). While the amount of Am-241 in the pond waters was very low (0.5 - 0.7 pCi/l), it was above the established Colorado stream standard of 0.15 pCi/l for release to off site drainage waters. The rapid successful treatment of these waters to the regulatory limit was important to the site for two reasons. The first was that the pond was approaching its hold-up limit. Without rapid treatment and release of the Pond A-4 water, typical spring run-off would require water management actions to other drainages onsite or a mass shuttling of water for disposal. The second reason was that this type of contaminated water had not been treated to the stringent stream standard at Rocky Flats before. Technical challenges in treatment could translate to impacts on water and secondary waste management, and ultimately, cost impacts. All of the technical challenges and specific site criteria led to the conclusion that a different approach to the treatment of this problem was necessary and a crash treatability program to identify applicable treatment techniques was undertaken. The goal of this program was to develop treatment options that could be implemented very quickly and would result in the generation of no high volume secondary waste that would be costly to dispose. A novel chemical treatment system was developed and implemented at the RFETS to treat Am

  10. Plutonium, americium, 90Sr and 137Cs in bones of red fox (Vulpes vulpes) from Eastern Poland

    International Nuclear Information System (INIS)

    Mietelski, J.W.; Tomankiewicz, E.; Gaca, P.; Blazej, S.; Kitowski, I.

    2008-01-01

    90 Sr, 238,239+240 Pu, 241 Am and 137 Cs activity concentrations are presented in the jaw bones of red fox (Vulpes vulpes) from eastern Poland. The short description of the applied radiochemical method is presented. Activity concentrations for 90 Sr ranged between 2.2±0.7 and 41.4±4.7 Bq/kg (aw = ash weight). Average results for plutonium and americium are on the level of 10 mBq/kg (aw). No clear relationship was observed among the radionuclide concentrations. The samples analyzed do not show elevated contamination levels when compared with results of bones of small animals (rodent or insectivorous mammals) determined previously, so no accumulation of bone seeking isotopes on higher step of food-chain is concluded. (author)

  11. Ecological distribution and fate of plutonium and americium in a processing waste pond on the Hanford Reservation

    International Nuclear Information System (INIS)

    Emergy, R.M.; Klopfer, D.C.; McShane, M.C.

    1978-01-01

    U Pond, located on the Hanford Reservation, has received low-level quantities of plutonium (Pu) and americium (Am) longer than any other aquatic environment in the world. Its ecological complexity and content of transuranics make it an ideal resource for information concerning the movement of these actinides within and out of an aquatic ecosystem. U Pond has been intensively inventoried for Pu concentrations in the ecological compartments and characterized limnologically in terms of its physicochemial parameters, biological productivity, and community structure. This work provides a basis for evaluating the pond's performance in retaining waste transuranics. The quantitative estimation of export routes developed by this study is important in determining how effectively such ponds act as retainers for transuranic wastes

  12. Comparative study of G2 delay and survival after /sup 241/Americium-. cap alpha. and /sup 60/Cobalt-. gamma. irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Luecke-Huhle, C.; Comper, W.; Hieber, L.; Pech, M.

    1982-06-01

    Survival and G2 delay following exposure to either /sup 60/Cobalt-..gamma..-rays or /sup 241/Americium-..cap alpha..-particles were studied in eight mammalian cell lines of human and animal origin including human fibroblasts from normal individuals and from patients with Ataxia telangiectasia or Fanconi's anemia. For both endpoints the effectiveness of alpha particle was greater as compared to ..gamma..-rays. RBE values for G2 delay (4.6-9.2) were in general comparable to RBE values derived from initial slopes of survival curves but higher compared to the ratio of mean inactivation doses. Ataxia cells were particularly sensitive to cell killing by ..gamma..-irradiation, however, showed average sensitivity to ..cap alpha..-particles of high LET. With the exception of Ataxia cells, cell killing and G2 delay seem to be related processes if individual cell cycle parameters are taken into account.

  13. Crystallographic and Spectroscopic Characterization of Americium Complexes Containing the Bis[(phosphino)methyl]pyridine-1-oxide (NOPOPO) Ligand Platform

    Energy Technology Data Exchange (ETDEWEB)

    Corbey, Jordan F. [Pacific Northwest National Laboratory, Richland, Washington 99354, United States; Rapko, Brian M. [Pacific Northwest National Laboratory, Richland, Washington 99354, United States; Wang, Zheming [Pacific Northwest National Laboratory, Richland, Washington 99354, United States; McNamara, Bruce K. [Pacific Northwest National Laboratory, Richland, Washington 99354, United States; Surbella, Robert G. [Pacific Northwest National Laboratory, Richland, Washington 99354, United States; Pellegrini, Kristi L. [Pacific Northwest National Laboratory, Richland, Washington 99354, United States; Schwantes, Jon M. [Pacific Northwest National Laboratory, Richland, Washington 99354, United States

    2018-02-06

    Abstract The crystal structures of americium species containing a common multi-functional phosphine oxide ligand, reported for its ability to extract f elements from acidic solutions, namely 2,6-[Ph2P(O)CH2]2C5H3-NO, L, have finally been determined after over three decades of separations studies involving these species and their surrogates. The molecular compounds Am(L)(NO3)3, Am 1:1, and [Am(L)2(NO3)][NO3]2, Am 2:1, along with their neodymium and europium analogs were synthesized and characterized using single-crystal X-ray crystallography, attenuated total reflectance Fourier transform infrared (ATR) spectroscopy and luminescence spectroscopy to provide a comprehensive comparison with new and known analogous complexes.

  14. Separation of americium by liquid-liquid extraction using diglycol-amides water-soluble complexing agents

    Energy Technology Data Exchange (ETDEWEB)

    Chapron, S.; Marie, C.; Pacary, V.; Duchesne, M.T.; Miguirditchian, M. [CEA, Centre de Marcoule, Nuclear Energy Division, RadioChemistry and Processses Departement, 30207 Bagnols-sur-Ceze (France); Arrachart, G.; Pellet-Rostaing, S. [Institut de Chimie Separative de Marcoule, LTSM, Bat 426, F-30207 Bagnols-sur- Ceze (France)

    2016-07-01

    Recycling americium (Am) alone from spent nuclear fuels is an important option studied for the future nuclear cycle (Generation IV systems) since Am belongs to the main contributors of the long-term radiotoxicity and heat power of final waste. Since 2008, a liquid-liquid extraction process called EXAm has been developed by the CEA to allow the recovery of Am alone from a PUREX raffinate (a dissolution solution already cleared from U, Np and Pu). A mixture of DMDOHEMA (N,N'-dimethyl-N,N'-dioctyl-2-(2-(hexyloxy)ethyl)-malonamide) and HDEHP (di-2-ethylhexylphosphoric acid) in TPH is used as the solvent and the Am/Cm selectivity is improved using TEDGA (N,N,N',N'-tetraethyl-diglycolamide) as a selective complexing agent to maintain Cm and heavier lanthanides in the acidic aqueous phase (5 M HNO{sub 3}). Americium is then stripped selectively from light lanthanides at low acidity (pH=3) with a poly-aminocarboxylic acid. The feasibility of sole Am recovery was already demonstrated during hot tests in ATALANTE facility and the EXAm process was adapted to a concentrated raffinate to optimize the process compactness. The speciation of TEDGA complexes formed in the aqueous phase with Am, Cm and lanthanides was studied to better understand and model the behavior of TEDGA in the process. Some Ln-TEDGA species are extracted into the organic phase and this specific chemistry might play a role in the Am/Cm selectivity improvement. Hence the hydrophilicity-lipophilicity balance of the complexing agent is an important parameter. In this comprehensive study, new analogues of TEDGA were synthesized and tested in the EXAm process conditions to understand the relationship between their structure and selectivity. New derivatives of TEDGA with different N-alkyl chain lengths and ramifications were synthesized. The impact of lipophilicity on ligand partitioning and Am/Cm selectivity was investigated. (authors)

  15. Proceedings of the Sandia Laboratories workshop on the use of titanate ion exchangers for defense waste management

    International Nuclear Information System (INIS)

    Schwoebel, R.L.; Northrup, C.J.

    1978-01-01

    Abstracts and visual aids from the following talks are presented: removal of radionuclides from Hanford defense waste solutions; waste management programs at Savannah River Plant; application of defense waste decontamination; americium and curium recovery from nuclear waste using inorganic ion exchanger materials; removal of trace 106 Ru in nuclear waste processing; and titanate characterization and consolidation processes. Copies of three memos are included: 90 Sr radiation effects on sodium titanate loaded macroreticular resin; 238 239 Pu content in defense waste; and preparation and physical properties of sodium titanate in ion exchange resin

  16. Thermodynamic approach of the poly-azine - f element ions interaction in aqueous conditions

    International Nuclear Information System (INIS)

    Miguirditchian, M.; Guillaumont, D.; Moisy, P.; Guillaneux, D.; Madic, C.

    2004-01-01

    2-Amino-4,6-di-(pyridine-2-yl)-1,3,5-triazine (Adptz) was considered as a model compound for selective aromatic nitrogen extractants (poly-azines) of minor actinides. Thermodynamic data ( ΔG 0 , ΔH 0 , ΔS 0 ) were systematically acquired for the complexation of lanthanide(III) ions as well as yttrium(III) and americium(III) in hydro-alcoholic medium. Two complementary experimental approaches were followed. Stability constants for the formation of the 1:1 complexes were evaluated from UV-visible spectrophotometry titration experiments, whereas enthalpies and entropies of reaction were obtained consistently from either temperature dependence experiments or micro-calorimetry. The interaction of Adptz with lanthanide(III) and yttrium(III) ions was found to be essentially ionic and dependent upon the hydration and size of the ion. As for americium(III) ion, stability constant and enthalpy of complexation was significantly larger. This was attributed to a partial electronic transfer from the ligand to empty orbitals of the cation. DFT calculations support this interpretation. (authors)

  17. Inspection report of unauthorized possession and use of unsealed americium-241 and subsequent confiscation, J.C. Haynes Company, Newark, Ohio

    International Nuclear Information System (INIS)

    1985-11-01

    This US Nuclear Regulatory Commission report documents the circumstances surrounding the March 26, 1985, confiscation and subsequent decontamination activities related to the use of unauthorized quantities of americium-241 at the John C. Haynes Company (licensee) of Newark, Ohio. It focuses on the period from early February to July 26, 1985. The incident started when NRC Region III recieved information that John C. Haynes possessed unauthorized quantities of americium-241 and was conducting unauthorized activities (diamond irradiation). By July 26, 1985, the decontamination activities at the licensee's laboratory were concluded. The licensee's actions with diamond irradiation resulted in contamination in restricted and unrestricted areas of the facility. The confiscation and decontamination activities required the combined efforts of NRC, Federal Bureau of Investigation, US Department of Energy, Oak Ridge Associated Universities, the State of Ohio, and the US Environmental Protection Agency. The report describes the factual information and significant findings associated with the confiscation and decontamination activities

  18. Ion-ion collisions

    International Nuclear Information System (INIS)

    Salzborn, Erhard; Melchert, Frank

    2000-01-01

    Collisions between ions belong to the elementary processes occurring in all types of plasmas. In this article we give a short overview about collisions involving one-electron systems. For collisions involving multiply-charged ions we limit the discussion to one specific quasi-one-electron system. (author)

  19. Experimental study of Americium-241 biokinetics in Homarus Gammarus lobster. Analysis of the accumulation and detoxication mechanisms at the sub-cellular level

    International Nuclear Information System (INIS)

    Paquet, F.

    1991-12-01

    The Americium 241 radioelement accumulation and elimination rate and mechanisms in the lobster organism have been experimentally studied; incorporation and detoxification capacities of each organ are evaluated. The existence of various biological compartments is shown; the major role of the digestive gland in accumulation of the radioelement, its distribution towards the various organs, and its resorption is comprehensively described, with an analysis at the subcellular and molecular levels. 401 p., 65 fig., 43 tab., 428 ref

  20. An experimental study of americium-241 biokinetics in the Lobster Homarus Gammarus. Analysis of the accumulation/storage and detoxification processes at the subcellular level

    International Nuclear Information System (INIS)

    Paquet, F.

    1993-01-01

    An experimental study of americium-241 kinetics has been conducted in the lobster Homarus gammmarus. The investigations were conducted at all the levels from the whole body to the subcellular and molecular levels. The animals were contaminated by a single or chronic ingestion of 241 Am labelled mussels. Assessments of accumulation, elimination and distribution of the radionuclide were established on organisms kept in the laboratory; they made it possible to demonstrate the importance of the digestive gland in the radionuclide transfer pathways. The preliminary results led to structural then ultrastructural investigations of the digestive gland in association with radioautographic studies and cellular extractions methods. Four cellular types were demonstrated, only two of them being implied in the radionuclide retention, the former being responsible for americium intake and the latter for its long-term retention. By means of biochemical techniques, subcellular accumulation was studied and the organelles implied in the nuclide retention were specified. Finally, a method of cellular nuclei dissociation was developed; it made it possible to analyse the molecular nature of americium ligands and to demonstrate the function of the protein nuclear matrix in the nuclide retention

  1. A new method for the determination of plutonium and americium using high pressure microwave digestion and alpha-spectrometry or ICP-SMS

    International Nuclear Information System (INIS)

    Luisier, F.; Corcho Alvarado, J.A.; Froidevaux, P.; Steinmann, P.; Krachler, M.

    2009-01-01

    Plutonium and americium are radionuclides particularly difficult to measure in environmental samples because they are a-emitters and therefore necessitate a careful separation before any measurement, either using radiometric methods or ICP-SMS. Recent developments in extraction chromatography resins such as Eichrom R TRU and TEVA have resolved many of the analytical problems but drawbacks such as low recovery and spectral interferences still occasionally occur. Here, we report on the use of the new Eichrom R DGA resin in association with TEVA resin and high pressure microwave acid leaching for the sequential determination of plutonium and americium in environmental samples. The method results in average recoveries of 83 ± 15% for plutonium and 73 ± 22% for americium (n = 60), and a less than 10% deviation from reference values of four IAEA reference materials and three samples from intercomparisons exercises. The method is also suitable for measuring 239 Pu in water samples at the μBq/l level, if ICP-SMS is used for the measurement. (author)

  2. Interaction of cesium, cobalt and americium with sediments and rocks of inshas site

    Energy Technology Data Exchange (ETDEWEB)

    Elreefy, S A; Marel, S A; Maghrawy, H B; Aly, A [Atomic energy authority, hot labs. and wast management center, (Egypt)

    1995-10-01

    Investigations were done on the interaction of radioactive Cs-134, Co-60 and Am-241 with soil and ground water of a proposed shallow disposal site at Inshas. Different samples representing the succession at different depths till 27.0 meter were taken from a digging well. These samples were mineralogically identified. Sorption behaviour of the investigated radionuclides from different aqueous media as well as the ground water in the site was studied. The percentage uptake of the radionuclides by the different soil samples was found to depend on different parameters such as, contact time, pH of the aqueous phase, volume to mass ratio and the presence of some competing ions in the aqueous phase. Results showed also that the sorption process depend on the nature of, the radionuclide, the type soil samples and the state of ions in solution. 7 tabs.

  3. Transfer of plutonium and americium to grass vegetation as a function of radionuclide solid - solution portioning in soil

    International Nuclear Information System (INIS)

    Sokolik, G.; Ovsiannikova, S.; Ivanova, T.; Leinova, S.; Kimlenka, I.; Zakharenkov, V.; Zakharenkova, N.

    2004-01-01

    The aim of investigation is to determine the main parameters influencing the plutonium and americium migration in the soil plant system including concentration factor Cf and distribution coefficient K d . The C f factor characterising the ratio of radionuclide activity concentration in the plant specie (A p , Bq/kg) and root-inhabited layer of soil (A s , Bq/kg) has been used as a measure of biological availability of TUE. The K d coefficient estimating the ratio between radionuclide activity concentration in the equilibrium solid phase (A s.ph. ) and pore solution (A sol. , Bq/l) is considered as a measure of sorption ability of soil in respect to the radionuclide. The biological availability of 239,240 Pu and 241 Am for different grass species in various mineral and organic soils of natural and agrarian systems has been studied. The soils and grass vegetation were sampled in 1994 - 2001 in Bragin, Narovla, Khoiniki districts of Belarus (12 - 53 km from ChNPP). Since plant uptake depends primarily on radionuclide portion in the pore soil solution the proper solutions were separated from the soil samples of root-inhabited layer with the method of high-speed centrifugation. 239,240 Pu and 241 Am in the samples were determined radiochemically using alpha-spectrometer ALPHA-KING 676 A. Influence of composition of soil solution on the radionuclide soil plant transfer has been analysed. The interrelationships between the concentration factor (C f ), portion of radionuclide in the soil solution and coefficient K d have been considered. The results of investigations clearly demonstrated the dependence of TUE concentration factors for meadow sedge-herbaceous association of soil sorbing complex. As a rule, C f of americium is higher than that of plutonium. Differentiating of soils according to the C f value and the forecast of grass vegetation contamination by TUE in the different periods after catastrophe has been done. The levels of various soils contamination to receive

  4. Development of a multi-functional reprocessing process based on ion-exchange method by using tertiary pyridine-type resin

    International Nuclear Information System (INIS)

    Koyama, Shin-ichi; Ozawa, Masaki; Suzuki, Tatsuya; Fujii, Yasuhiko

    2006-01-01

    A series of separation experiment was performed in order to study a multi-functional spent fuel reprocessing process based on ion-exchange technique. The tertiary pyridine-type anion-exchange resin was used in this experiment and the mixed oxide fuel highly irradiated in the experimental fast reactor ''JOYO'' was used as a reference spent fuel. As the result, 106 Ru + 125 Sb, 137 Cs + 155 Eu + 144 Ce, plutonium, americium and curium could be separated from the irradiated fuel by only three steps of ion-exchange. The decontamination factor of 137 Cs and trivalent lanthanides ( 155 Eu, 144 Ce) in the final americium product exceeded 3.9 x 10 4 and 1.0 x 10 5 , respectively. The decontamination factor for the mutual separation of 243 Cm and 241 Am was larger than 2.2 x 10 3 for the americium product and, moreover, the content of 137 Cs, trivalent lanthanides and 243 Cm included in 241 Am product did not exceed 2 ppm. These results prove that the proposed simplified separation process has a reality as a candidate for future reprocessing process based on the partitioning and transmutation concept. (author)

  5. Ion implantation

    International Nuclear Information System (INIS)

    Dearnaley, Geoffrey

    1975-01-01

    First, ion implantation in semiconductors is discussed: ion penetration, annealing of damage, gettering, ion implanted semiconductor devices, equipement requirements for ion implantation. The importance of channeling for ion implantation is studied. Then, some applications of ion implantation in metals are presented: study of the corrosion of metals and alloys; influence or ion implantation on the surface-friction and wear properties of metals; hyperfine interactions in implanted metals

  6. 1976 Hanford americium-exposure incident: histologic and autoradiographic observations on skin

    International Nuclear Information System (INIS)

    Hampton, J.C.

    1982-01-01

    Examination of biopsies from exposed and relatively unexposed areas of the face revealed changes that were consistent with actinic elastic degeneration associated with solar exposure, except in the areas in which sources of alpha radiation were detected in the upper dermis. In those areas particles judged to be ion exchange resin were found within a few macrophages and extracellularly among connective tissue fibers. Elastic fibers in those areas showed more advanced degenerative change than fibers not closely associated with heavy concentrations of alpha radiation

  7. Chemical behaviour of americium in natural aquatic solutions: Hydrolysis, radiolysis and redox reactions

    International Nuclear Information System (INIS)

    Stadler, S.; Kim, J.I.

    1988-06-01

    Hydrolysis and redox reactions of the Am(III) and Am(V) ions have been investigated in NaClO 4 and NaCl solutions as well as in natural saline groundwaters. The hydrolysis constants of Am(OH) n 3-n species and the solubility product of Am(OH) 3 (s) have been determined in 0.1 M NaClO 4 , 0.1 M NaCl and 0.6 M NaCl solutions. As observed in concentrated NaCl solutions (> 3 M), the α-radiation induces the radiolytic oxidation of the Cl - -ion to produce Cl 2 , HClO, ClO - and other oxidized species, which result in a strongly oxidizing medium. Consequently Am(III) is oxidized to Am(V). Under these conditions the hydrolysis constants of AmO 2 (OH) n 1-n species and the solubility product are also determined. The α-radiation induced radiolysis reactions in NaCl solution and the subsequent oxidation reaction of Am(III) have been systematically investigated by varying pH, NaCl concentration and specific α-activity. Also included in the investigation are a few selected groundwaters of relatively high salinity from the Gorleben aquifer systems. (orig.) [de

  8. The distribution and remobilisation of plutonium and americium in estuaries of the eastern Irish Sea: a review

    International Nuclear Information System (INIS)

    Toole, J.

    1993-01-01

    The plutonium and americium components in the authorised discharges from BNFL Sellafield are rapidly removed from Irish Sea seawater onto the particulate phase. These actinides tend to be concentrated in fine sediment deposits on the Irish Sea bed and in estuaries where fine sediment accumulates. This paper focuses on these estuarine areas and brings together the available data on the levels and distributions of Pu and Am within the estuarine sediments. The results from field and laboratory experiments which have been undertaken in order to determine the degree of Pu and Am remobilisation, and the mechanism responsible, are also reviewed. These sediment-associated actinides may undergo both chemical and physical remobilisation, leading to increased dissolved concentrations in low-salinity waters and to apparent losses from the estuary on the sediment phase under certain conditions. Saltmarsh sediments are demonstrated to be the most important reservoirs for Pu and Am. The radiological significance of the levels of Pu and Am found in these and in other sediments is summarised, by comparison with GDLs. The appropriateness of GDLs for assessing the radiological significance of Pu and Am in these saltmarsh sediments is discussed. A more site-specific assessment methodology is recommended. (author)

  9. Characteristics of plutonium and americium contamination at the former U.K. atomic weapons test ranges at Maralinga and Emu

    International Nuclear Information System (INIS)

    Burns, P.A.; Cooper, M.B.; Lokan, K.H.; Wilks, M.J.; Williams, G.A.

    1995-01-01

    Physico-chemical studies on environmental plutonium are described, which provide data integral to an assessment of dose for the inhalation of artificial actinides by Australian Aborigines living a semi-traditional lifestyle at Maralinga and Emu, sites of U.K. atomic weapons tests between 1953 and 1963. The most significant area, from a radiological perspective, is the area contaminated by plutonium in a series of ''one point'' safety trials in which large quantities of plutonium were dispersed explosively at a location known as Taranaki. The activity distribution of plutonium and americium with particle size is quite different from the mass distribution, as a considerably higher proportion of the activity is contained in the finer (inhalable) fraction than of the mass. Except in areas which were disturbed through ploughing during a cleanup in 1967, most the activity remains in the top 1 cm of the surface. Much of the activity is in particulate form, even at distances > 20 km from the firing sites, and discrete particles have been located even at distances beyond 100 km. Data are presented which permit the assessment of annual committed doses through the inhalation pathway, for Aborigines living a semi-traditional lifestyle in the areas affected by the Taranaki firings in particular. (author)

  10. Characterization of a sealed Americium-Beryllium (AmBe) source by inductively coupled plasma mass spectrometry

    International Nuclear Information System (INIS)

    Sommers, J.; Jimenez, M.; Adamic, M.; Giglio, J.; Carney, K.

    2009-01-01

    Two Americium-Beryllium neutron sources were dismantled, sampled (sub-sampled) and analyzed via inductively coupled plasma mass spectrometry (ICP-MS). Characteristics such as 'age' since purification, actinide content, trace metal content and inter and intra source composition were determined. The 'age' since purification of the two sources was determined to be 25.0 and 25.4 years, respectively. The systematic uncertainties in the 'age' determination were ±4% 2σ. The amount and isotopic composition of U and Pu varied substantially between the sub-samples of Source 2 (n = 8). This may be due to the physical means of sub-sampling or the way the source was manufactured. Source 1 was much more consistent in terms of content and isotopic composition (n = 3 sub-samples). The Be-Am ratio varied greatly between the two sources. Source 1 had an Am-Be ratio of 6.3 ± 52% (1σ). Source 2 had an Am-Be ratio of 9.81 ± 3.5% (1σ). In addition, the trace element content between the samples varied greatly. Significant differences were determined between Sources 1 and 2 for Sc, Sr, Y, Zr, Mo, Ba and W. (author)

  11. Vertical transport of particulate-associated plutonium and americium in the upper water column of the Northeast Pacific

    International Nuclear Information System (INIS)

    Fowler, S.W.; Ballestra, S.; La Rosa, J.; Fukai, R.

    1983-01-01

    Concentrations of plutonium (Pu) and americium (Am) were determined in seawater, suspended particulate matter, sediment trap samples, and biogenic material collected at the VERTEX I site in the North Pacific off central California. From a vertical profile taken over the upper 1500 m, the presence of sub-surface maxima of sup(239+240)Pu and 241 Am were identified between 100 to 750 m and 250 to 750 m, respectively. A large fraction (32%) of the filterable sup(239+240)Pu in surface waters was associated with cells during a phytoplankton bloom; Pu:Am activity ratios in surface water and the suspended particles indicated that Pu was concentrated by the cells to a greater degree than Am. However, similar measurements beneath the surface layer showed an overall enrichment of Am over Pu on fine suspended particles with depth. Freshly produced zooplankton fecal pellets and large, fast sinking particles collected in PITS contained relatively high concentrations of Pu and Am. Both transuranic concentrations in trapped particles and transuranic flux tended to increase with depth down to 750 m, suggesting that their scavenging is in the upper water column. Am appeared to be scavenged by sinking biogenic particles to a greater extent than Pu. The results are discussed. (author)

  12. Kinetics of ethylenediaminetetraacetate exchange of americium (3) with copper (2) in aqueous solution

    International Nuclear Information System (INIS)

    Nikitenko, S.I.; Martynenko, L.I.; Pechurova, N.I.

    1985-01-01

    By the method of spectrophotometry exchange kinetics in the AmA - -Cu 2+ , where A 4- -ethylenediaminetetraacetate, is studied. The values of exchange rate constants and thermodynamic activation parameters have been found. It is shown that exchange of central ions is rialized according to the dissociative mechanism with formation of intermediate protonated complexes and according to the associative mechanism with formation of binuclear intermediates. The exchange mechanisms identity for AmA - and LnA - , where Ln 3+ -RE cations of cerium subgroup is proved. It is assumed that values of activation entropy in exchange processes are determined by the radius of the leaving cation and of activation enthalpy - by the peculiarities of the electronic structure

  13. Experimental study of Americium-241 biokinetics in Homarus Gammarus lobster. Analysis of the accumulation and detoxication mechanisms at the sub-cellular level; Etude experimentale des biocinetiques de l`americium-241 chez le homard homarus gammarus. Analyse des mecanismes d`accumulation et de detoxication au niveau subcellulaire

    Energy Technology Data Exchange (ETDEWEB)

    Paquet, F

    1991-12-01

    The Americium 241 radioelement accumulation and elimination rate and mechanisms in the lobster organism have been experimentally studied; incorporation and detoxification capacities of each organ are evaluated. The existence of various biological compartments is shown; the major role of the digestive gland in accumulation of the radioelement, its distribution towards the various organs, and its resorption is comprehensively described, with an analysis at the subcellular and molecular levels. 401 p., 65 fig., 43 tab., 428 ref.

  14. Chemical behaviour of trivalent and pentavalent americium in saline NaCl-solutions. Studies of transferability of laboratory data to natural conditions. Interim report. Reported period: 1.2.1993-31.12.1993

    International Nuclear Information System (INIS)

    Runde, W.; Kim, J.I.

    1994-09-01

    In order to clarify the chemical behaviour of Americium in saline aqueous systems relevant for final storage this study deals with the chemical reactions of trivalent and pentavalent Americium in NaCl-solutions under the influence of radiolysis from its own alpha radiation. The focus of the study was on investigating the geologically relevant reactions, such as hydrolysis or carbonate- and chloride complexing in solid-liquid equilibriums. Comprehensive measurements on solubility and spectroscopic studies in NaCl-solutions were carried out in a CO 2 -free atmosphere and 10 -2 atm CO 2 partial pressure. Identification and characterisation of the AM (III) and AM(V) solid phases were supplemented by structural research with the chemically analogue EU (III) and Np(V) compounds. The alpha-radiation induced radiolysis in saline NaCl solutions and the redox behaviour of Americium which was influenced thereby were spectroscopically quantified. (orig.) [de

  15. Direct-scanning alpha spectrometer for americium and plutonium contamination on highly-enriched uranium surfaces

    International Nuclear Information System (INIS)

    Ward, W.C.; Martinez, H.E.; Abeyta, C.L.; Morgan, A.N.; Nelson, T.O.

    1997-01-01

    Trace Pu 239 and Am 241 contamination on a surface whose alpha count is dominated by U 235 and U 234 decay has been successfully quantified by counting swipes in external alpha spectroscopy chambers. The swipe process, however, is labor intensive and subject to uncertainties in the swiping process as well as degraded spectral resolution due to the presence of the swipe material. A multichannel instrument for automated in situ measurements of interior and exterior contamination has been developed which incorporates a rotary table, 13 fixed ion-implanted silicon detectors, and spectroscopy electronics. Custom software was written to allow alpha spectrometer to function as a virtual instrument in the LabView environment. This system gives improved speed and resolution as well as a complete log of the location of areas of high surface contamination, a feature not practical to obtain by other methods, and one which opens the possibility of long term studies such as Pu outgrowth evaluation employing the instrument. The authors present performance data as well as system integration, calibration, control, and dynamic geometric efficiency calculations related to the design of this and next generation systems

  16. Transfer across the human gut of environmental plutonium, americium, cobalt, caesium and technetium: studies with cockles (Cerastoderma edule) from the Irish Sea

    International Nuclear Information System (INIS)

    Hunt, G.J.

    1998-01-01

    Our previous studies have indicated lower values of the gut transfer factor ('f L values') for plutonium and americium in winkles (Littorina littorea) than adopted by ICRP. The present study was undertaken primarily to investigate whether this observation extends to other species. Samples of cockles (Cerastoderma edule) from Ravenglass, Cumbria were eaten by volunteers who provided 24 samples of urine and faeces. Urine samples indicated f L values for cockles which were higher than for winkles; for plutonium these ranged overall up to 7x10 -4 with an arithmetic mean in the range (2-3)x10 -4 , and for americium up to 2.6x10 -4 with an arithmetic mean of 1.2x10 -4 . Limited data based on volunteers eating cockles from the Solway suggest that f L values for americium may be greater at distance from Sellafield. The measured values compare with 5x10 -4 used by the ICRP for environmental forms of both elements, which would appear to provide adequate protection when calculating doses from Cumbrian cockles. Data for other nuclides were obtained by analysing faecal samples from the volunteers who ate the Ravenglass cockles. Cobalt-60 showed an f L value in the region of 0.2, twice the value currently used by ICRP. For 137 Cs, variabilities were indicated in the range 0.08 to 0.43, within the ICRP value of f L =1.0. Technetium-99 gave f L values up to about 0.6, in reasonable conformity with the ICRP value of 0.5. (author)

  17. An experimental study of americium-241 biokinetics in the Lobster Homarus Gammarus. Analysis of the accumulation/storage and detoxification processes at the subcellular level; Etude experimentale des biocinetiques de l`americium-241 chez le homard homarus gammarus. Analyse des mecanismes d`accumulation et de detoxication au niveau subcellulaire

    Energy Technology Data Exchange (ETDEWEB)

    Paquet, F

    1993-01-01

    An experimental study of americium-241 kinetics has been conducted in the lobster Homarus gammmarus. The investigations were conducted at all the levels from the whole body to the subcellular and molecular levels. The animals were contaminated by a single or chronic ingestion of {sup 241} Am labelled mussels. Assessments of accumulation, elimination and distribution of the radionuclide were established on organisms kept in the laboratory; they made it possible to demonstrate the importance of the digestive gland in the radionuclide transfer pathways. The preliminary results led to structural then ultrastructural investigations of the digestive gland in association with radioautographic studies and cellular extractions methods. Four cellular types were demonstrated, only two of them being implied in the radionuclide retention, the former being responsible for americium intake and the latter for its long-term retention. By means of biochemical techniques, subcellular accumulation was studied and the organelles implied in the nuclide retention were specified. Finally, a method of cellular nuclei dissociation was developed; it made it possible to analyse the molecular nature of americium ligands and to demonstrate the function of the protein nuclear matrix in the nuclide retention.

  18. Determination by gamma-ray spectrometry of the plutonium and americium content of the Pu/Am separation scraps. Application to molten salts; Determination par spectrometrie gamma de la teneur en plutonium et en americium de produits issus de separation Pu/Am. Application aux bains de sels

    Energy Technology Data Exchange (ETDEWEB)

    Godot, A. [CEA Valduc, Dept. de Traitement des Materiaux Nucleaires, 21 - Is-sur-Tille (France); Perot, B. [CEA Cadarache, Dept. de Technologie Nucleaire, Service de Modelisation des Transferts et Mesures Nucleaires, 13 - Saint-Paul-lez-Durance (France)

    2005-07-01

    Within the framework of plutonium recycling operations in CEA Valduc (France), americium is extracted from molten plutonium metal into a molten salt during an electrolysis process. The scraps (spent salt, cathode, and crucible) contain extracted americium and a part of plutonium. Nuclear material management requires a very accurate determination of the plutonium content. Gamma-ray spectroscopy is performed on Molten Salt Extraction (MSE) scraps located inside the glove box, in order to assess the plutonium and americium contents. The measurement accuracy is influenced by the device geometry, nuclear instrumentation, screens located between the sample and the detector, counting statistics and matrix attenuation, self-absorption within the spent salt being very important. The purpose of this study is to validate the 'infinite energy extrapolation' method employed to correct for self-attenuation, and to detect any potential bias. We present a numerical study performed with the MCNP computer code to identify the most influential parameters and some suggestions to improve the measurement accuracy. A final uncertainty of approximately 40% is achieved on the plutonium mass. (authors)

  19. Picomolar traces of americium(III) introduce drastic changes in the structural chemistry of terbium(III). A break in the ''gadolinium break''

    Energy Technology Data Exchange (ETDEWEB)

    Welch, Jan M. [TU Wien, Atominstitut, Vienna (Austria); Mueller, Danny; Knoll, Christian; Wilkovitsch, Martin; Weinberger, Peter [TU Wien, Institute of Applied Synthetic Chemistry, Vienna (Austria); Giester, Gerald [University of Vienna, Institute of Mineralogy and Crystallography, Vienna (Austria); Ofner, Johannes; Lendl, Bernhard [TU Wien, Institute of Chemical Technologies and Analytics, Vienna (Austria); Steinhauser, Georg [Leibniz Universitaet Hannover, Institute of Radioecology and Radiation Protection (Germany)

    2017-10-16

    The crystallization of terbium 5,5{sup '}-azobis[1H-tetrazol-1-ide] (ZT) in the presence of trace amounts (ca. 50 Bq, ca. 1.6 pmol) of americium results in 1) the accumulation of the americium tracer in the crystalline solid and 2) a material that adopts a different crystal structure to that formed in the absence of americium. Americium-doped [Tb(Am)(H{sub 2}O){sub 7}ZT]{sub 2} ZT.10 H{sub 2}O is isostructural to light lanthanide (Ce-Gd) 5,5{sup '}-azobis[1H-tetrazol-1-ide] compounds, rather than to the heavy lanthanide (Tb-Lu) 5,5{sup '}-azobis[1H-tetrazol-1-ide] (e.g., [Tb(H{sub 2}O){sub 8}]{sub 2}ZT{sub 3}.6 H{sub 2}O) derivatives. Traces of Am seem to force the Tb compound into a structure normally preferred by the lighter lanthanides, despite a 10{sup 8}-fold Tb excess. The americium-doped material was studied by single-crystal X-ray diffraction, vibrational spectroscopy, radiochemical neutron activation analysis, and scanning electron microscopy. In addition, the inclusion properties of terbium 5,5{sup '}-azobis[1H-tetrazol-1-ide] towards americium were quantified, and a model for the crystallization process is proposed. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

  20. Observations on the redistribution of plutonium and americium in the Irish Sea sediments, 1978 to 1996: concentrations and inventories

    International Nuclear Information System (INIS)

    Kershaw, P.J.; Denoon, D.C.; Woodhead, D.S.

    1999-01-01

    The distribution of plutonium and americium in the sub-tidal sediments of the Irish Sea is described following major surveys in 1978, 1983, 1988 and 1995. Concentrations in surface sediments have declined near the source at Sellafield since 1988. Time-series of inter-tidal surface sediment concentrations are presented from 1977 onwards, revealing the importance of sediment reworking and transport in controlling the evolution of the environmental signal. The surface and near-surface sediments, in the eastern Irish Sea 'mud-patch', are generally well mixed with respect to Pu (α) and 241 Am distributions but show increasing variability with depth - up to 4 orders of magnitude in concentration. The inventories of 239,240 Pu and 241 Am in the sub-tidal sediments have been estimated and compared with the reported decay-corrected discharges. These amounted to 360 and 545 TBq respectively, in 1995, about 60% of the total decay-corrected discharge. Part of the unaccounted fraction may be due to unrepresentative sampling of the seabed. It is speculated that some tens of TBq of plutonium and 241 Am reside undetected in the large volumes of coarse-grained, sub-tidal and inter-tidal sediment which characterise much of the Irish Sea. This has been due to the inability of the available corers to penetrate to the base of contamination in these mobile sediments. Further observations are needed to verify and quantify the missing amount. A budget of plutonium-α and 241 Am has been estimated based on published observations in the three main compartments: water column, sub-tidal and inter-tidal sediments. This amounts to 460-540 TBq and 575-586 TBq respectively, or 64-75% and 60-61%, of the decay-corrected reported discharge. (Copyright (c) 1999 Elsevier Science B.V., Amsterdam. All rights reserved.)

  1. Measurement of total alpha activity of neptunium, plutonium, and americium in highly radioactive Hanford waste by iron hydroxide precipitation and 2-heptanone solvent extraction

    International Nuclear Information System (INIS)

    Maiti, T.C.; Kaye, J.H.

    1992-06-01

    An improved method has been developed to concentrate the major alpha-emitting actinide elements neptunium, plutonium, and americium from samples with high salt content such as those resulting from efforts to characterize Hanford storage tank waste. Actinide elements are concentrated by coprecipitation of their hydroxides using iron carrier. The iron is removed by extraction from 8M HCI with 2-heptanone. The actinide elements remain in the aqueous phase free from salts, iron, and long-lived fission products. Recoveries averaged 98 percent

  2. Extraction of americium (III) by thermosensitive polymer gel copolymerized with acidic phosphorus compound

    International Nuclear Information System (INIS)

    Takeshita, Kenji; Nakano, Yoshio; Matsumura, Tatsuro

    2001-01-01

    A new gel-liquid extraction using a thermosensitive gel was proposed. The thermosensitive gel shows the conformational change of polymer network with temperature, which is known as the phase transition phenomena of gel. The extraction rate and equilibrium of Am(III) in an aqueous solution containing nitrate ion were measured batchwise by using a thermosensitive gel, N-isopropylacrylamide (NIPA) copolymerized with 2-methacryloyloxy- ethylacidphosphate (MR). The effects of the conformational change of polymer network on the extraction rate and equilibrium were discussed. The distribution ratio of Am(III) showed a large value at higher than LCST (low critical solution temperature; 34degC) and was decreased by the phase transition of gel from shrinking to swelling with decreasing temperature. The extraction of Am(III) in the aqueous solution and the release of Am(III) extracted in the gel were repeated stably by the temperature swing operation between 40 and 3degC. The extraction mechanism of Am(III) was described simply as Am 3+ + 3R - OH=(R-O) 3 Am + 3H + (R-OH: MR). The equilibrium constant at the shrinking state (40degC) was more than 3 times of that at swelling state (3degC). The gel-phase diffusivity of Eu(III) used as a substitute of Am(III) was evaluated as the order of 10 -12 m 2 /s at either of 3 or 40degC, which was similar to those for practical extraction chromatographic resins. The temperature-response of gel for the extraction of Eu(III) was very excellent without delay even for the rapid temperature change at 10degC/min. These results suggest that the extraction and release of Am(III) in an aqueous solution can be controlled by the conformational change of polymer network of thermosensitive gel. (author)

  3. Optimization conditions for the separation of rare earth elements, americium, curium and cesium with HPLC technique

    International Nuclear Information System (INIS)

    Goutelard, F.; Caussignac, C.; Brennetot, R.; Stadelmann, G.; Gautier, C.

    2009-01-01

    In order to validate the neutronic code calculations used in the nuclear field, it is necessary to quantify the isotopic composition of the nuclear irradiated fuels with high precision and accuracy. A separation step whose objective is to isolate the elements of interest in a fraction as pure as possible, is performed before mass spectrometry detection (MC-ICP-MS, TIMS), in order to eliminate isobaric interferences. In a first step, uranium and plutonium are separated from the fission products by ion exchange chromatography. Then, fission products are separated by high performance liquid chromatography (HPLC). A gradient separation with a silica sulphonated support as stationary phase and hydroxy-methyl butyric acid (HMB) as eluent solution provides a good degree of separation of the rare earth elements, Am, Cm and Cs. But, for a same manufacturer, the rate of sulphonated groups is variable from one column to another for a given production batch. For every replacement of column, it is necessary to adjust the separation conditions. Furthermore, the high radioactivity of the samples injected damages the stationary phase, dragging a regular renewal of the columns. The goal of this study is to determine the optimal separation conditions with a minimum of tests in order to limit the time assigned to this operation. A first Doehlert experimental design with pH and HMB concentration as variables has been implemented to optimize Gd, Eu separation, in isocratic initial conditions. A second one has been tested in order to separate the higher lanthanides and to fix the final conditions of the gradient separation. A last set of tests has been performed to characterize the cesium behaviour. Finally, the gradient conditions have been adjusted in order to perform the full separation of lanthanides, Cs, Am and Cm with nuclear facilities. (author)

  4. Advanced integrated solvent extraction and ion exchange systems

    International Nuclear Information System (INIS)

    Horwitz, P.

    1996-01-01

    Advanced integrated solvent extraction (SX) and ion exchange (IX) systems are a series of novel SX and IX processes that extract and recover uranium and transuranics (TRUs) (neptunium, plutonium, americium) and fission products 90 Sr, 99 Tc, and 137 Cs from acidic high-level liquid waste and that sorb and recover 90 Sr, 99 Tc, and 137 Cs from alkaline supernatant high-level waste. Each system is based on the use of new selective liquid extractants or chromatographic materials. The purpose of the integrated SX and IX processes is to minimize the quantity of waste that must be vitrified and buried in a deep geologic repository by producing raffinates (from SX) and effluent streams (from IX) that will meet the specifications of Class A low-level waste

  5. Solvent extraction of some metal ions by dithiocarbamate types of chemically modified lipophilic chitosan

    International Nuclear Information System (INIS)

    Inoue, K.; Nakagawa, H.; Naganawa, H.; Tachimori, S.

    2001-01-01

    Chitosan is a basic polysaccharide containing primary amino groups with high reactivity. we prepared O,O'-decanoyl chitosan and dithiocarbamate O,O'-decanoyl chitosan; the former was soluble in chloroform and toluene, while latter was soluble not only these diluents but also in some aliphatic diluents such as hexane and kerosene which are employed in commercial scale solvent extraction. Solvent extraction by dithiocarbamate O,O'-decanoyl chitosan in kerosene was tested for some base metal ions from sulfuric acid solution. The sequence of selectivity for these metal ions was found to be as follows: Cu(II) >> Ni(II) > Cd(II) ∼ Fe(III) > Co(II) ∼ Zn(II). Copper(II) was quantitatively extracted at pH > 1 and quantitatively stripped with 2 M sulfuric acid solution. Solvent extraction of silver(I) and gold(III) from hydrochloric acid as well as lanthanides and americium(III) from nitrate solution were also tested. Americium was selectively extracted over trivalent lanthanides, suggesting a high possibility for the final treatment of high level radioactive wastes. (authors)

  6. Sorption of carbon, cobalt, nickel, strontium, iodine, cesium, americium and neptumium in rocks and minerals

    International Nuclear Information System (INIS)

    Pinnoja, S.; Jaakkola, T.; Kaemaeraeinen, E.L.; Koskinen, A.; Lindberg, A.

    1984-09-01

    Sorption of the radionuclides C-14, Co-58, Ni-63, I-125, Sr-85, Cs-134, Am-241 and Np-237, which are important in nuclear waste, were studied in rock by autoradiographic method. Samples were selected to represent common rocks and minerals in Finnish bedrock: rapakivi granite, tonalite, mica gneiss, granodiorite, biotite, quartz, plagioclase, K feldspar and hornblende. Polished thin sections were used to determine the contributions of different minerals to the sorption of the radionuclides. Sawn rock pieces (1.2 x 1.2 x 1.6 cm) were used to determine the Ksub(a)-values for rough rock surfaces where penetration into the rock matrix was found. The sorption order of the elements determined with the rock pieces was Ksub(a)sup(Cs)>Ksub(a)sup(Ni)>Ksub(a)sup(Co)>Ksub(a)sup(Sr)>Ksub(a)sup(C)>Ksub(a)sup(I). The same order of sorption was determined with thin sections for all nuclides except carbon, which was not sorbed on thin sections. Wide differences in the Ksub(a)-values for different minerals were found for Cs and Sr. The sorption mechanism for these elements is presumed to be ion exchange. The Ksub(a)-values of Cs varied between 0.1 x 10 -4 and 600 x 10 -4 m 3 /m 2 and those for Sr between 0.01 x 10 -4 and 10 x 10 -4 m 3 /m 2 . The lowest values were determined for quartz and the highest for biotite. Radionuclides having a tendency to form pseudocolloids and hydroxide precipitates (Am, Np, Ni) were sorbed on thin sections with only small variation in Ksub(a)-values: all values were between 1 x 10 -4 and 10 x 10 -4 and 100 x 10 -4 m 3 /m 2 . A very good agreement was found between experimental and calculated Ksub(a)-values for rock thin sections. Ksub(a)-values were calculated by multiplying the percentages of individual minerals in the rock by the Ksub(a)-values of the corresponding pure minerals and summing the results. Calculated Ksub(a)-values were occasionally up to 50% smaller than the experimental ones, owing to the low contents of some high adsorbing minerals

  7. Computer modelling of the chemical speciation of Americium (III) in human body fluids

    International Nuclear Information System (INIS)

    Jiang, Shu-bin; Lei, Jia-rong; Wang, He-yi; Zhong, Zhi-jing; Yang, Yong; Du, Yang

    2008-01-01

    A multi-phase equilibrium model consisted of multi-metal ion and low molecular mass ligands in human body fluid has been constructed to discuss the speciation of Am 3+ in gastric juice, sweat, interstitial fluid, intracellular fluid and urine of human body, respectively. Computer simulations indicated that the major Am(III)P Species were Am 3+ , [Am Cl] 2+ and [AmH 2 PO 4 ] 2+ at pH 4 became dominant with higher pH value when [Am] = 1 x 10 -7 mol/L in gastric juice model and percentage of AmPO 4 increased with [Am]. in sweat system, Am(III) existed with soluble species at pH 4.2∼pH 7.5 when [Am] = 1 x 10 -7 mol/L and Am(III) existed with Am 3+ and [Am OH] 2+ at pH 6.5 when [Am] -10 mol/L or [Am] > 5 x 10 -8 mol/L . With addition of EDTA, the Am(III) existed with soluble [Am EDTA] - whereas the Am(III) existed with insoluble AmPO 4 when [Am] > 1 x 10 -12 mol/L at interstitial fluid. The major Am(III) species was AmPO 4 at pH 7.0 and [Am]=4 x 10 -12 mol/L in intracellular fluid, which implied Am(III) represented strong cell toxicity. The percentage of Am(III) soluble species increased at lower pH hinted that the Am(III), in the form of aerosol, ingested by macrophage, could released into interstitial fluid and bring strong toxicity to skeleton system. The soluble Am(III) species was dominant when pH 4 when pH > 4.5 when [Am] = 1 x 10 -10 Pmol/L in human urine, so it was favorable to excrete Am(III) from kidney by taking acid materials. (author)

  8. Synthesis of zirconia sol stabilized by trivalent cations (yttrium and neodymium or americium): a precursor for Am-bearing cubic stabilized zirconia.

    Science.gov (United States)

    Lemonnier, Stephane; Grandjean, Stephane; Robisson, Anne-Charlotte; Jolivet, Jean-Pierre

    2010-03-07

    Recent concepts for nuclear fuel and targets for transmuting long-lived radionuclides (minor actinides) and for the development of innovative Gen-IV nuclear fuel cycles imply fabricating host phases for actinide or mixed actinide compounds. Cubic stabilized zirconia (Zr, Y, Am)O(2-x) is one of the mixed phases tested in transmutation experiments. Wet chemical routes as an alternative to the powder metallurgy are being investigated to obtain the required phases while minimizing the handling of contaminating radioactive powder. Hydrolysis of zirconium, neodymium (a typical surrogate for americium) and yttrium in aqueous media in the presence of acetylacetone was firstly investigated. Progressive hydrolysis of zirconium acetylacetonate and sorption of trivalent cations and acacH on the zirconia particles led to a stable dispersion of nanoparticles (5-7 nm) in the 6-7 pH range. This sol gels with time or with temperature. The application to americium-containing solutions was then successfully tested: a stable sol was synthesized, characterized and used to prepare cubic stabilized zirconia (Zr, Y, Am)O(2-x).

  9. Ion Colliders

    CERN Document Server

    Fischer, W

    2014-01-01

    High-energy ion colliders are large research tools in nuclear physics to study the Quark-Gluon-Plasma (QGP). The range of collision energy and high luminosity are important design and operational considerations. The experiments also expect flexibility with frequent changes in the collision energy, detector fields, and ion species. Ion species range from protons, including polarized protons in RHIC, to heavy nuclei like gold, lead and uranium. Asymmetric collision combinations (e.g. protons against heavy ions) are also essential. For the creation, acceleration, and storage of bright intense ion beams, limits are set by space charge, charge change, and intrabeam scattering effects, as well as beam losses due to a variety of other phenomena. Currently, there are two operating ion colliders, the Relativistic Heavy Ion Collider (RHIC) at BNL, and the Large Hadron Collider (LHC) at CERN.

  10. Recoil ions

    International Nuclear Information System (INIS)

    Cocke, C.L.; Olson, R.E.

    1991-01-01

    The collision of a fast moving heavy ion with a neutral atomic target can produce very highly charged but slowly moving target ions. This article reviews experimental and theoretical work on the production and use of recoil ions beyond the second ionization state by beams with specific energies above 0.5 MeV/amu. A brief historical survey is followed by a discussion of theoretical approaches to the problem of the removal of many electrons from a neutral target by a rapid, multiply charged projectile. A discussion of experimental techniques and results for total and differential cross sections for multiple ionization of atomic and molecular targets is given. Measurements of recoil energy are discussed. The uses of recoil ions for in situ spectroscopy of multiply charged ions, for external beams of slow, highly charged ions and in ion traps are reviewed. Some possible future opportunities are discussed. (orig.)

  11. The MARINE experiment: Irradiation of sphere-pac fuel and pellets of UO{sub 2−x} for americium breeding blanket concept

    Energy Technology Data Exchange (ETDEWEB)

    D' Agata, E., E-mail: elio.dagata@ec.europa.eu [European Commission, Joint Research Centre, Institute for Energy and Transport, P.O. Box 2, NL-1755 ZG Petten (Netherlands); Hania, P.R. [Nuclear Research and Consultancy Group, P.O. Box 25, NL-1755 ZG Petten (Netherlands); Freis, D.; Somers, J. [European Commission, Joint Research Centre, Institute for Transuranium Elements, P.O. Box 2340, D-76125 Karlsruhe (Germany); Bejaoui, S. [Commissariat à l’Energie Atomique et aux Energies Alternatives, DEN/DEC, F-13108 St. Paul lez Durance Cedex (France); Charpin, F.F.; Baas, P.J.; Okel, R.A.F.; Til, S. van [Nuclear Research and Consultancy Group, P.O. Box 25, NL-1755 ZG Petten (Netherlands); Lapetite, J.-M. [European Commission, Joint Research Centre, Institute for Energy and Transport, P.O. Box 2, NL-1755 ZG Petten (Netherlands); Delage, F. [Commissariat à l’Energie Atomique et aux Energies Alternatives, DEN/DEC, F-13108 St. Paul lez Durance Cedex (France)

    2017-01-15

    Highlights: • MARINE is designed to check the behaviour of MABB sphere-pac concept. • MABB sphere-pac are compared with MABB pellet. • Swelling and helium release behaviour will be the main output of the experiment. • An experiment to check sphere-pac MADF fuel behaviour has been already performed. - Abstract: Americium is a strong contributor to the long term radiotoxicity of high activity nuclear waste. Transmutation by irradiation in nuclear reactors of long-lived nuclides like {sup 241}Am is therefore an option for the reduction of radiotoxicity and heat production of waste packages to be stored in a repository. The MARINE irradiation experiment is the latest of a series of European experiments on americium transmutation (e.g. EFTTRA-T4, EFTTRA-T4bis, HELIOS, MARIOS, SPHERE) performed in the High Flux Reactor (HFR). The MARINE experiment is developed and carried out in the framework of the collaborative research project PELGRIMM of the EURATOM 7th Framework Programme (FP7). During the past years of experimental works in the field of transmutation and tests of innovative nuclear fuels, the release or trapping of helium as well as swelling have been shown to be the key issues for the design of such kind of fuel both as drivers and even more for Am-bearing blanket targets (due to the higher Am contents). The main objective of the MARINE experiment is to study the in-pile behaviour of uranium oxide fuel containing 13% of americium and to compare the behaviour of sphere-pac versus pellet fuel, in particular the role of microstructure and temperature on fission gas release and He on fuel swelling. The MARINE experiment will be irradiated in 2016 in the HFR in Petten (The Netherlands) and is expected to be completed in spring 2017. This paper discusses the rationale and objective of the MARINE experiment and provides a general description of its design for which some innovative features have been adopted.

  12. Investigation of the chemical explosion of an ion exchange resin column and resulting americium contamination of personnel in the 242-Z building, August 30, 1976

    Energy Technology Data Exchange (ETDEWEB)

    1976-10-19

    As a result of an explosion in the Waste Treatment Facility, 242-Z Building, 200 West Area of the Hanford Reservation on August 30, 1976, the Manager of the Richland Operations Office (RL), Energy Research and Development Administration (ERDA), appointed an ERDA Committee to conduct a formal investigation and to prepare a report on their findings of this occurrence. The Committee was instructed to conduct the investigation in accordance with ERDAMC 0502, insofar as circumstances would permit, to cover and explain technical elements of the casual sequence(s) of the occurrence, and to describe management systems which should have or could have prevented the occurrence. This report is the result of the investigation and presents the conclusions of the review.

  13. Ion colliders

    International Nuclear Information System (INIS)

    Fischer, W.

    2010-01-01

    Ion colliders are research tools for high-energy nuclear physics, and are used to test the theory of Quantum Chromo Dynamics (QCD). The collisions of fully stripped high-energy ions create matter of a temperature and density that existed only microseconds after the Big Bang. Ion colliders can reach higher densities and temperatures than fixed target experiments although at a much lower luminosity. The first ion collider was the CERN Intersecting Storage Ring (ISR), which collided light ions (77Asb1, 81Bou1). The BNL Relativistic Heavy Ion Collider (RHIC) is in operation since 2000 and has collided a number of species at numerous energies. The CERN Large Hadron Collider (LHC) started the heavy ion program in 2010. Table 1 shows all previous and the currently planned running modes for ISR, RHIC, and LHC. All three machines also collide protons, which are spin-polarized in RHIC. Ion colliders differ from proton or antiproton colliders in a number of ways: the preparation of the ions in the source and the pre-injector chain is limited by other effects than for protons; frequent changes in the collision energy and particle species, including asymmetric species, are typical; and the interaction of ions with each other and accelerator components is different from protons, which has implications for collision products, collimation, the beam dump, and intercepting instrumentation devices such a profile monitors. In the preparation for the collider use the charge state Z of the ions is successively increased to minimize the effects of space charge, intrabeam scattering (IBS), charge change effects (electron capture and stripping), and ion-impact desorption after beam loss. Low charge states reduce space charge, intrabeam scattering, and electron capture effects. High charge states reduce electron stripping, and make bending and acceleration more effective. Electron stripping at higher energies is generally more efficient. Table 2 shows the charge states and energies in the

  14. Ion colliders

    Energy Technology Data Exchange (ETDEWEB)

    Fischer, W.

    2011-12-01

    Ion colliders are research tools for high-energy nuclear physics, and are used to test the theory of Quantum Chromo Dynamics (QCD). The collisions of fully stripped high-energy ions create matter of a temperature and density that existed only microseconds after the Big Bang. Ion colliders can reach higher densities and temperatures than fixed target experiments although at a much lower luminosity. The first ion collider was the CERN Intersecting Storage Ring (ISR), which collided light ions [77Asb1, 81Bou1]. The BNL Relativistic Heavy Ion Collider (RHIC) is in operation since 2000 and has collided a number of species at numerous energies. The CERN Large Hadron Collider (LHC) started the heavy ion program in 2010. Table 1 shows all previous and the currently planned running modes for ISR, RHIC, and LHC. All three machines also collide protons, which are spin-polarized in RHIC. Ion colliders differ from proton or antiproton colliders in a number of ways: the preparation of the ions in the source and the pre-injector chain is limited by other effects than for protons; frequent changes in the collision energy and particle species, including asymmetric species, are typical; and the interaction of ions with each other and accelerator components is different from protons, which has implications for collision products, collimation, the beam dump, and intercepting instrumentation devices such a profile monitors. In the preparation for the collider use the charge state Z of the ions is successively increased to minimize the effects of space charge, intrabeam scattering (IBS), charge change effects (electron capture and stripping), and ion-impact desorption after beam loss. Low charge states reduce space charge, intrabeam scattering, and electron capture effects. High charge states reduce electron stripping, and make bending and acceleration more effective. Electron stripping at higher energies is generally more efficient. Table 2 shows the charge states and energies in the

  15. Inhaled americium dioxide

    International Nuclear Information System (INIS)

    Park, J.F.

    1982-01-01

    This project includes experiments to determine the effects of Zn-DTPA therapy on the retention, translocation and biological effects of inhaled 241 AmO 2 . Beagle dogs that received inhalation exposure to 241 AmO 2 developed leukopenia, clincial chemistry changes associated with hepatocellular damage, and were euthanized due to respiratory insufficiency caused by radiation pneumonitis 120 to 131 days after pulmonary deposition of 22 to 65 μCi 241 Am. Another group of dogs that received inhalation exposure to 241 AmO 2 and were treated daily with Zn-DTPA had initial pulmonary deposition of 19 to 26 μCi 241 Am. These dogs did not develop respiratory insufficiency, and hematologic and clinical chemistry changes were less severe than in the non-DTPA-treated dogs

  16. Americium-241 Decorporation Model

    Science.gov (United States)

    2014-10-01

    non- pyrogenic ampoules suitable for intravenous administration (FDA 2004, Hameln 2004). This is a standard formulation, which is a fixed parameter...4.4.6. Toxicity/Side Effects Treatment with DTPA can deplete endogenous metals, which is why the Zn salt is preferred for long-term treatment...However, other endogenous metals may be depleted if treatment spans several months. During prolonged treatments serum levels of essential metals should be

  17. Artificial radionuclides in the Northern European Marine Environment. Distribution of radiocaesium, plutonium and americium in sea water and sediments in 1995

    International Nuclear Information System (INIS)

    Groettheim, Siri

    2000-01-01

    This study considers the distribution of radiocaesium, plutonium and americium in the northern marine environment. The highest radiocaesium activity in sea water was observed in Skagerrak, 26 Bq/m 3 , and in surface sediments in the Norwegian Sea, 60 Bq/kg. These enhanced levels were related to Chernobyl. The highest 239,240Pu activity in surface water was measured in the western North Sea, 66 mBq/m 3 . In sea water, sub-surface maxima were observed at several locations with an 239,240Pu activity up to 160 mBq/m 3 , and were related to Sellafield. With the exception to the North Sea, surface sediments reflected Pu from global fallout from weapons tests only. (author)

  18. Safe handling of kilogram amounts of fuel-grade plutonium and of gram amounts of plutonium-238, americium-241 and curium-244

    International Nuclear Information System (INIS)

    Louwrier, K.P.; Richter, K.

    1976-01-01

    During the past 10 years about 600 glove-boxes have been installed at the Institute for Transuranium Elements at Karlsruhe. About 80% of these glove-boxes have been designed and equipped for handling 100-g to 1-kg amounts of 239 Pu containing 8-12% 240 Pu (low-exposure plutonium). A small proportion of the glove-boxes is equipped with additional shielding in the form of lead sheet or lead glass for work with recycled plutonium. In these glove-boxes gram-amounts of 241 Am have also been handled for preparation of Al-Am targets using tongs and additional shielding inside the glove-boxes themselves. Water- and lead-shielded glove-boxes equipped with telemanipulators have been installed for routine work with gram-amounts of 241 Am, 243 Am and 244 Cm. A prediction of the expected radiation dose for the personnel is difficult and only valid for a preparation procedure with well-defined preparation steps, owing to the fact that gamma dose-rates depend strongly upon proximity and source seize. Gamma radiation dose measurements during non-routine work for 241 Am target preparation showed that handling of gram amounts leads to a rather high irradiation dose for the personnel, despite lead or steel glove-box shielding and shielding within the glove-boxes. A direct glove-hand to americium contact must be avoided. For all glove-handling of materials with gamma radiation an irradiation control of the forearms of the personnel by, for example, thermoluminescence dosimeters is necessary. Routine handling of americium and curium should be executed with master-slave equipment behind neutron and gamma shielding. (author)

  19. ion irradiation

    Indian Academy of Sciences (India)

    Swift heavy ions interact predominantly through inelastic scattering while traversing any polymer medium and produce excited/ionized atoms. Here samples of the polycarbonate Makrofol of approximate thickness 20 m, spin coated on GaAs substrate were irradiated with 50 MeV Li ion (+3 charge state). Build-in ...

  20. Ion microprobes

    International Nuclear Information System (INIS)

    Coles, J.N.; Long, J.V.P.

    1977-01-01

    An ion microprobe is described that has an ion extraction arrangement comprising two separate paths for ions and electrons diverging from a common point. A cone shaped or pyramidal guard electrode surrounds each path the apex angles being equal and coinciding with the said point. The guard electrodes are positioned to lie tangentially to each other and to a planar surface including the said point. An aperture is provided for the two paths at the apexes of both guard electrodes, and electrical connections between the guard electrodes enable the same potential to be applied to both guard electrodes. Means are provided for generating oppositely polarised electric fields within the guard electrodes, together with means for causing a focused ion beam to strike the common point without suffering astigmatism. The means for causing a focused ion beam to strike the said point includes an ion gun for directing an ion beam along one of the paths and means to provide an axial accelerating field there along. Optical viewing means are also provided. Existing designs enable only ions or electrons, but not both, to be extracted at any one time. (U.K.)

  1. Ion implantation

    International Nuclear Information System (INIS)

    Johnson, E.

    1986-01-01

    It is the purpose of the present paper to give a review of surface alloy processing by ion implantation. However, rather than covering this vast subject as a whole, the survey is confined to a presentation of the microstructures that can be found in metal surfaces after ion implantation. The presentation is limited to alloys processed by ion implantation proper, that is to processes in which the alloy compositions are altered significantly by direct injection of the implanted ions. The review is introduced by a presentation of the processes taking place during development of the fundamental event in ion implantation - the collision cascade, followed by a summary of the various microstructures which can be formed after ion implantation into metals. This is compared with the variability of microstructures that can be achieved by rapid solidification processing. The microstructures are subsequently discussed in the light of the processes which, as the implantations proceed, take place during and immediately after formation of the individual collision cascades. These collision cascades define the volumes inside which individual ions are slowed down in the implanted targets. They are not only centres for vigorous agitation but also the sources for formation of excess concentrations of point defects, which will influence development of particular microstructures. A final section presents a selection of specific structures which have been observed in different alloy systems. (orig./GSCH)

  2. Water-soluble metal-binding polymers with ultrafiltration: A technology for the removal, concentration, and recovery of metal ions from aqueous streams

    International Nuclear Information System (INIS)

    Smith, B.F.; Robison, T.W.; Jarvinen, G.D.

    1997-01-01

    The use of water-soluble metal-binding polymers coupled with ultrafiltration (UF) is a technology under development to selectively concentrate and recover valuable or regulated metal-ions from dilute process or waste waters. The polymers have a sufficiently large molecular size that they can be separated and concentrated using commercially available UF technology. The polymers can then be reused by changing the solution conditions to release the metal-ions, which are recovered in a concentrated form for recycle or disposal. Pilot-scale demonstrations have been completed for a variety of waste streams containing low concentrations of metal ions including electroplating wastes (zinc and nickel) and nuclear waste streams (plutonium and americium). Many other potential commercial applications exist including remediation of contaminated solids. An overview of both the pilot-scale demonstrated applications and small scale testing of this technology are presented

  3. Water-soluble metal-binding polymers with ultrafiltration: A technology for the removal, concentration, and recovery of metal ions from aqueous streams

    Energy Technology Data Exchange (ETDEWEB)

    Smith, B.F.; Robison, T.W.; Jarvinen, G.D.

    1997-12-31

    The use of water-soluble metal-binding polymers coupled with ultrafiltration (UF) is a technology under development to selectively concentrate and recover valuable or regulated metal-ions from dilute process or waste waters. The polymers have a sufficiently large molecular size that they can be separated and concentrated using commercially available UF technology. The polymers can then be reused by changing the solution conditions to release the metal-ions, which are recovered in a concentrated form for recycle or disposal. Pilot-scale demonstrations have been completed for a variety of waste streams containing low concentrations of metal ions including electroplating wastes (zinc and nickel) and nuclear waste streams (plutonium and americium). Many other potential commercial applications exist including remediation of contaminated solids. An overview of both the pilot-scale demonstrated applications and small scale testing of this technology are presented.

  4. Energy Transfer between U(VI) and Eu(III) Ions Adsorbed on a Silica Surface

    Energy Technology Data Exchange (ETDEWEB)

    Park, K. K.; Cha, W.; Cho, H. R.; Im, H. J.; Jung, E. C.; Song, K. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2011-05-15

    Understanding of chemical behavior of actinide in a groundwater flow is important for assessing the possibility of their migration with water flows in a radioactive waste disposal site. Uranium is ubiquitous in the environment and a major actinide in a nuclear fuel cycle. Americium and curium having isotopes of long half life are minor actinides in a spent fuel. If a minor actinide coexists with uranium in a groundwater flow, some interactions between them could be expected such as minor actinide adsorption onto uranium precipitates and competition with each other for an adsorption to a mineral surface site. Eu(III) ion is frequently used as a chemical analogue of Am(III) and Cm(III) ions in a migration chemistry. The luminescent spectra of U(VI) and Eu(III) ions show a dependency on the coordination symmetry around them, and the changes in intensity or bandwidth of spectra can yield valuable information on their local environment. The luminescent lifetime also strongly depends on the coordination environment, and its measurement is valuable in probe studies on micro-heterogeneous systems. The excited U(VI) ion can be quenched through Stern.Volmer process, hydrolysis of excited species, exciplex formation, electron transfer or energy transfer. In case of U(VI)-Eu(III) system, the interaction between two ions can be studied by measuring the effect of Eu(III) ion on the quenching of U(VI) ion luminescence. There are only a few investigations on the interaction between an excited U(VI) ion and a lanthanide(III) ion. In perchlorate solution, the energy transfer to Eu(III) ion occurred only in solutions of pH>3.87. In this study, the quenching of U(VI) luminescence by Eu(III) on a silica surface was measured. The results will be discussed on the basis of a chemical interaction between them

  5. Actinide Oxidation State and O/M Ratio in Hypostoichiometric Uranium-Plutonium-Americium U0.750Pu0.246Am0.004O2-x Mixed Oxides.

    Science.gov (United States)

    Vauchy, Romain; Belin, Renaud C; Robisson, Anne-Charlotte; Lebreton, Florent; Aufore, Laurence; Scheinost, Andreas C; Martin, Philippe M

    2016-03-07

    Innovative americium-bearing uranium-plutonium mixed oxides U1-yPuyO2-x are envisioned as nuclear fuel for sodium-cooled fast neutron reactors (SFRs). The oxygen-to-metal (O/M) ratio, directly related to the oxidation state of cations, affects many of the fuel properties. Thus, a thorough knowledge of its variation with the sintering conditions is essential. The aim of this work is to follow the oxidation state of uranium, plutonium, and americium, and so the O/M ratio, in U0.750Pu0.246Am0.004O2-x samples sintered for 4 h at 2023 K in various Ar + 5% H2 + z vpm H2O (z = ∼ 15, ∼ 90, and ∼ 200) gas mixtures. The O/M ratios were determined by gravimetry, XAS, and XRD and evidenced a partial oxidation of the samples at room temperature. Finally, by comparing XANES and EXAFS results to that of a previous study, we demonstrate that the presence of uranium does not influence the interactions between americium and plutonium and that the differences in the O/M ratio between the investigated conditions is controlled by the reduction of plutonium. We also discuss the role of the homogeneity of cation distribution, as determined by EPMA, on the mechanisms involved in the reduction process.

  6. Validation of Am-241 measurement in ion chamber type smoke detector by using gamma spectrometry system

    International Nuclear Information System (INIS)

    Yii Mei Wo; Khairul Nizam Razali

    2005-01-01

    Smoke detectors are useful devices in modern days that able to save many lives. Even though, the use of ion chamber type smoke detector (usually contain Americium-241) was exempted in Malaysia, but the trading of this device was controlled by regulation, under the Atomic Energy Licensing Act (Act 304). The activity of the Am-241 can be measured by using the Gamma Spectrometry System since it was much easier, compared to Alpha Spectrometry System. To do so, the system was first need to be calibrated using the standard reference source to find the efficiency of the germanium detector. The method used for the measurement was first validated for several relevant parameters, which include specificity, precision (repeatability), bias (accuracy), linearity, working range, detection limit, robustness and ruggedness to ensure it was fit for the purpose. The measured Am-241 activity inside the smoke detector will be reported together with a reasonable expanded uncertainty arise from the measurement. (Author)

  7. Americium, plutonium and uranium contamination and speciation in well waters, streams and atomic lakes in the Sarzhal region of the Semipalatinsk Nuclear Test Site, Kazakhstan.

    Science.gov (United States)

    León Vintró, L; Mitchell, P I; Omarova, A; Burkitbayev, M; Jiménez Nápoles, H; Priest, N D

    2009-04-01

    New data are reported on the concentrations, isotopic composition and speciation of americium, plutonium and uranium in surface and ground waters in the Sarzhal region of the Semipalatinsk Test Site, and an adjacent area including the settlement of Sarzhal. The data relate to filtered water and suspended particulate from (a) streams originating in the Degelen Mountains, (b) the Tel'kem 1 and Tel'kem 2 atomic craters, and (c) wells on farms located within the study area and at Sarzhal. The measurements show that (241)Am, (239,240)Pu and (238)U concentrations in well waters within the study area are in the range 0.04-87mBq dm(-3), 0.7-99mBq dm(-3), and 74-213mBq dm(-3), respectively, and for (241)Am and (239,240)Pu are elevated above the levels expected solely on the basis of global fallout. Concentrations in streams sourced in the Degelen Mountains are similar, while concentrations in the two water-filled atomic craters are somewhat higher. Suspended particulate concentrations in well waters vary considerably, though median values are very low, at 0.01mBq dm(-3), 0.08mBq dm(-3) and 0.32mBq dm(-3) for (241)Am, (239,240)Pu and (238)U, respectively. The (235)U/(238)U isotopic ratio in almost all well and stream waters is slightly elevated above the 'best estimate' value for natural uranium worldwide, suggesting that some of the uranium in these waters is of test-site provenance. Redox analysis shows that on average most of the plutonium present in the microfiltered fraction of these waters is in a chemically reduced form (mean 69%; 95% confidence interval 53-85%). In the case of the atomic craters, the proportion is even higher. As expected, all of the americium present appears to be in a reduced form. Calculations suggest that annual committed effective doses to individual adults arising from the daily ingestion of these well waters are in the range 11-42microSv (mean 21microSv). Presently, the ground water feeding these wells would not appear to be contaminated with

  8. Americium, plutonium and uranium contamination and speciation in well waters, streams and atomic lakes in the Sarzhal region of the Semipalatinsk Nuclear Test Site, Kazakhstan

    Energy Technology Data Exchange (ETDEWEB)

    Leon Vintro, L. [School of Physics, University College Dublin, Belfield, Dublin 4 (Ireland)], E-mail: luis.leon@ucd.ie; Mitchell, P.I.; Omarova, A. [School of Physics, University College Dublin, Belfield, Dublin 4 (Ireland); Burkitbayev, M. [Department of Inorganic Chemistry, Al-Faraby Kazakh National University, Almaty (Kazakhstan); Jimenez Napoles, H. [School of Physics, University College Dublin, Belfield, Dublin 4 (Ireland); Priest, N.D. [School of Health and Social Sciences, Middlesex University, Enfield, EN3 4SA (United Kingdom)

    2009-04-15

    New data are reported on the concentrations, isotopic composition and speciation of americium, plutonium and uranium in surface and ground waters in the Sarzhal region of the Semipalatinsk Test Site, and an adjacent area including the settlement of Sarzhal. The data relate to filtered water and suspended particulate from (a) streams originating in the Degelen Mountains, (b) the Tel'kem 1 and Tel'kem 2 atomic craters, and (c) wells on farms located within the study area and at Sarzhal. The measurements show that {sup 241}Am, {sup 239,240}Pu and {sup 238}U concentrations in well waters within the study area are in the range 0.04-87 mBq dm{sup -3}, 0.7-99 mBq dm{sup -3}, and 74-213 mBq dm{sup -3}, respectively, and for {sup 241}Am and {sup 239,240}Pu are elevated above the levels expected solely on the basis of global fallout. Concentrations in streams sourced in the Degelen Mountains are similar, while concentrations in the two water-filled atomic craters are somewhat higher. Suspended particulate concentrations in well waters vary considerably, though median values are very low, at 0.01 mBq dm{sup -3}, 0.08 mBq dm{sup -3} and 0.32 mBq dm{sup -3} for {sup 241}Am, {sup 239,240}Pu and {sup 238}U, respectively. The {sup 235}U/{sup 238}U isotopic ratio in almost all well and stream waters is slightly elevated above the 'best estimate' value for natural uranium worldwide, suggesting that some of the uranium in these waters is of test-site provenance. Redox analysis shows that on average most of the plutonium present in the microfiltered fraction of these waters is in a chemically reduced form (mean 69%; 95% confidence interval 53-85%). In the case of the atomic craters, the proportion is even higher. As expected, all of the americium present appears to be in a reduced form. Calculations suggest that annual committed effective doses to individual adults arising from the daily ingestion of these well waters are in the range 11-42 {mu}Sv (mean 21 {mu

  9. Solvent extraction of uranium(VI), plutonium(VI) and americium(III) with HTTA/HPMBP using mono- and bi-functional neutral donors. Synergism and thermodynamics

    International Nuclear Information System (INIS)

    Pai, S.A.; Lohithakshan, K.V.; Mithapara, P.D.; Aggarwal, S.K.

    2000-01-01

    Synergistic extraction of hexavalent uranium and plutonium as well as trivalent americium was studied in HNO 3 with thenoyl, trifluoro-acetone (HTTA)/1-phenyl, 3-methyl, 4-benzoyl pyrazolone-5 (HPMBP) in combination with neutral donors viz. DPSO, TBP, TOPO (mono-functional) and DBDECMP, DHDECMP, CMPO (bi-functional) with wide basicity range using benzene as diluent. A linear correlation was observed when the equilibrium constant log Ks for the organic phase synergistic reaction of both U(VI) and Pu(VI) with either of the chelating agents HTTA or HPMBP was plotted vs. the basicity (log Kh) of the donor (both mono- and bi-functional) indicating bi-functional donors also behave as mono-functional. This was supported by the thermodynamic data (ΔG 0 , ΔH 0 , ΔS 0 ) obtained for these systems. The organic phase adduct formation reactions were identified for the above systems from the thermodynamic data. In the Am(III) HTTA system log K s values of bi-functional donors were found to be very high and deviate from the linear plot (log K s vs. log K h ) obtained for mono-functional donors, indicating that they function as bi-functional for the Am(III)/HTTA) system studied. This was supported by high +ve ΔS 0 values obtained for this system. (author)

  10. Diluent and extractant effects on the enthalpy of extraction of uranium(VI) and americium(III) nitrates by trialkyl phosphates

    International Nuclear Information System (INIS)

    Srinivasan, T.G.; Vasudeva Rao, P.R.; Sood, D.D.

    1998-01-01

    The effect of various diluents such as n-hexane, n-heptane n-octane, isooctane, n-decane, n-undecane, n-dodecane, n-tetradecane, n-hexadecane, cyclohexane, benzene, toluene, p-xylene, mesitylene and o-dichlorobenzene on the enthalpy of extraction of uranyl nitrate by tri-n-amyl phosphate (TAP) over the temperature range 283 K--333 K has been studied. The results indicate that the enthalpy of extraction does not vary significantly with the diluents studied. Also enthalpies of extraction of uranyl nitrate and americium(III) nitrate by neutral organo phosphorous extractants such as tri-n-butyl phosphate (TBP), tri-n-amyl phosphate (TAP), tri-sec-butyl phosphate (TsBP), tri-isoamyl phosphate (TiAP) and tri-n-hexyl phosphate (THP) have been studied. An attempt has been made to explain the trends, on the basis of the nature of the solvate formed and the different terms which contribute to the overall enthalpy change

  11. The design of a multisource americium-beryllium (Am-Be) neutron irradiation facility using MCNP for the neutronic performance calculation.

    Science.gov (United States)

    Sogbadji, R B M; Abrefah, R G; Nyarko, B J B; Akaho, E H K; Odoi, H C; Attakorah-Birinkorang, S

    2014-08-01

    The americium-beryllium neutron irradiation facility at the National Nuclear Research Institute (NNRI), Ghana, was re-designed with four 20 Ci sources using Monte Carlo N-Particle (MCNP) code to investigate the maximum amount of flux that is produced by the combined sources. The results were compared with a single source Am-Be irradiation facility. The main objective was to enable us to harness the maximum amount of flux for the optimization of neutron activation analysis and to enable smaller sample sized samples to be irradiated. Using MCNP for the design construction and neutronic performance calculation, it was realized that the single-source Am-Be design produced a thermal neutron flux of (1.8±0.0007)×10(6) n/cm(2)s and the four-source Am-Be design produced a thermal neutron flux of (5.4±0.0007)×10(6) n/cm(2)s which is a factor of 3.5 fold increase compared to the single-source Am-Be design. The criticality effective, k(eff), of the single-source and the four-source Am-Be designs were found to be 0.00115±0.0008 and 0.00143±0.0008, respectively. Copyright © 2014 Elsevier Ltd. All rights reserved.

  12. The recycling of the actinides neptunium, americium and curium in a fast power reactor to reduce the long term activity in a final store

    International Nuclear Information System (INIS)

    Beims, H.D.

    1986-01-01

    The starting point for the considerations and calculations given in this dissertation is the inevitable production of radioactive materials in the use of nuclear energy, which creates a considerable potential danger in a final store for a very long period. As one possibility of alleviating this problem, a concept for recycling the waste actinides neptunium, americium and curium was proposed. The waste actinides are separated in the reprocessing of burnt-up fuel elements and reach a further irradiation circuit. There they pass through the stages 'manufacture of irradiation elements', 'use in a fast power reactor' and reprocessing of irradiation elements' several times. In each irradiation and subsequent storage, about 17% of the waste actinides are removed by fission or by conversion into nuclides which can be reused as fuel, so that during the life of 40 years of the fast recycling reacor, the waste actinides can be reduced in mass by one half. In order to determine this mass reduction effect, a model calculation was developed, which includes the representation of the neutron physics and thermal properties of the reactor core and the storage and reprocessing of the irradiation elements. (orig./RB) [de

  13. Human bones obtained from routine joint replacement surgery as a tool for studies of plutonium, americium and {sup 90}Sr body-burden in general public

    Energy Technology Data Exchange (ETDEWEB)

    Mietelski, Jerzy W., E-mail: jerzy.mietelski@ifj.edu.pl [Henryk Niewodniczanski Institute of Nuclear Physics, Polish Academy of Sciences, Radzikowskiego 152, 31-342 Cracow (Poland); Golec, Edward B. [Traumatology and Orthopaedic Clinic, 5th Military Clinical Hospital and Polyclinic, Independent Public Healthcare Facility, Wroclawska 1-3, 30-901 Cracow (Poland); Orthopaedic Rehabilitation Department, Chair of Clinical Rehabilitation, Faculty of Motor of the Bronislaw Czech' s Academy of Physical Education, Cracow (Poland); Department of Physical Therapy Basics, Faculty of Physical Therapy, Administration College, Bielsko-Biala (Poland); Tomankiewicz, Ewa [Henryk Niewodniczanski Institute of Nuclear Physics, Polish Academy of Sciences, Radzikowskiego 152, 31-342 Cracow (Poland); Golec, Joanna [Orthopaedic Rehabilitation Department, Chair of Clinical Rehabilitation, Faculty of Motor of the Bronislaw Czech' s Academy of Physical Education, Cracow (Poland); Physical Therapy Department, Institute of Physical Therapy, Faculty of Heath Science, Jagiellonian University, Medical College, Cracow (Poland); Nowak, Sebastian [Traumatology and Orthopaedic Clinic, 5th Military Clinical Hospital and Polyclinic, Independent Public Healthcare Facility, Wroclawska 1-3, 30-901 Cracow (Poland); Orthopaedic Rehabilitation Department, Chair of Clinical Rehabilitation, Faculty of Motor of the Bronislaw Czech' s Academy of Physical Education, Cracow (Poland); Szczygiel, Elzbieta [Physical Therapy Department, Institute of Physical Therapy, Faculty of Heath Science, Jagiellonian University, Medical College, Cracow (Poland); Brudecki, Kamil [Henryk Niewodniczanski Institute of Nuclear Physics, Polish Academy of Sciences, Radzikowskiego 152, 31-342 Cracow (Poland)

    2011-06-15

    The paper presents a new sampling method for studying in-body radioactive contamination by bone-seeking radionuclides such as {sup 90}Sr, {sup 239+240}Pu, {sup 238}Pu, {sup 241}Am and selected gamma-emitters, in human bones. The presented results were obtained for samples retrieved from routine surgeries, namely knee or hip joints replacements with implants, performed on individuals from Southern Poland. This allowed to collect representative sets of general public samples. The applied analytical radiochemical procedure for bone matrix is described in details. Due to low concentrations of {sup 238}Pu the ratio of Pu isotopes which might be used for Pu source identification is obtained only as upper limits other then global fallout (for example Chernobyl) origin of Pu. Calculated concentrations of radioisotopes are comparable to the existing data from post-mortem studies on human bones retrieved from autopsy or exhumations. Human bones removed during knee or hip joint surgery provide a simple and ethical way for obtaining samples for plutonium, americium and {sup 90}Sr in-body contamination studies in general public. - Highlights: > Surgery for joint replacement as novel sampling method for studying in-body radioactive contamination. > Proposed way of sampling is not causing ethic doubts. > It is a convenient way of collecting human bone samples from global population. > The applied analytical radiochemical procedure for bone matrix is described in details. > The opposite patient age correlations trends were found for 90Sr (negative) and Pu, Am (positive).

  14. Study and modeling of lanthanide(3)-L and americium(3)-L (With L = NTA, EDTA and DTPA) in high ionic strength aqueous solutions

    International Nuclear Information System (INIS)

    Rocchiccioli, F.

    2000-01-01

    The dissociation constants of NTA, EDTA, DTPA in NaCl, NaClO 4 , LiCl and LiClO 4 aqueous solutions of various ionic strengths have been gathered from the literature and from the Critical Surveys of Stability Constants. These values have been completed by a series of pKa values obtained in the same salted solution at higher ionic strengths by potentiometry involving a combined glass electrode at 25 deg C. The dependencies of the pKas versus the ionic strength have been investigated by using the Specific Interaction Theory (SIT), the parabolic model and the Pitzer model. The stability constants of complexes involving lanthanides (III), such as Nd 3+ , Eu 3+ and Lu 3+ , and americium (III), with the ligands previously mentioned in NaCl, NaClO 4 , LiCl and LiClO 4 aqueous solutions of high ionic strengths have been determined. The methods used for the determination of the stability constants for the lanthanide complexes are various: direct measurements by potentiometry when possible, UV-visible absorption spectroscopy involving Arsenazo (III) as a competitor ligand. For the actinide complexes, solvent extraction experiments have been performed. The different systems, along with the dissociation constants of several complexes in the same aqueous media, have been successfully modeled by the SIT, the parabolic method and the Pitzer method. (author)

  15. Ion channeling

    International Nuclear Information System (INIS)

    Erramli, H.; Blondiaux, G.

    1994-01-01

    Channeling phenomenon was predicted, many years ago, by stark. The first channeling experiments were performed in 1963 by Davies and his coworkers. Parallely Robinson and Oen have investigated this process by simulating trajectories of ions in monocrystals. This technique has been combined with many methods like Rutherford Backscattering Spectrometry (R.B.S.), Particles Induced X-rays Emission (P.I.X.E) and online Nuclear Reaction (N.R.A.) to localize trace elements in the crystal or to determine crystalline quality. To use channeling for material characterization we need data about the stopping power of the incident particle in the channeled direction. The ratios of channeled to random stopping powers of silicon for irradiation in the direction have been investigated and compared to the available theoretical results. We describe few applications of ion channeling in the field of materials characterization. Special attention is given to ion channeling combined with Charged Particle Activation Analysis (C.P.A.A.) for studying the behaviour of oxygen atoms in Czochralski silicon lattices under the influence of internal gettering and in different gaseous atmospheres. Association between ion channeling and C.P.A.A was also utilised for studying the influence of the growing conditions on concentration and position of carbon atoms at trace levels in the MOVPE Ga sub (1-x) Al sub x lattice. 6 figs., 1 tab., 32 refs. (author)

  16. Ion source

    International Nuclear Information System (INIS)

    1977-01-01

    The specifications of a set of point-shape electrodes of non-corrodable material that can hold a film of liquid material of equal thickness is described. Contained in a jacket, this set forms an ion source. The electrode is made of tungsten with a glassy carbon layer for insulation and an outer layer of aluminium-oxide ceramic material

  17. Ion-ion collisions and ion storage rings

    International Nuclear Information System (INIS)

    Mowat, J.R.

    1988-01-01

    Improved understanding of fundamental ion-ion interactions is expected to emerge from research carried out with ion storage rings. In this short survey the significant advantages and unique features that make stored ions useful targets for collision experiments are reviewed and discussed. It is pointed out that improvements to existing ion-ion experiments, as well as qualitatively new experiments, should occur over the next few years as ion storage rings become available for atomic physics. Some new experiments are suggested which are difficult if not impossible with present-day technology, but which seem feasible at storage rings facilities. (orig.)

  18. Solubility of plutonium and americium-241 from rumen contents of cattle grazing on plutonium-contaminated desert vegetation in in vitro bovine gastrointestinal fluids - August 1975 to January 1977

    International Nuclear Information System (INIS)

    Barth, J.; Giles, K.R.; Brown, K.W.

    1985-01-01

    The alimentary solubility of plutonium and americium-241 ingested by cattle grazing at Area 13 of the Nevada Test Site and the Clean Slate II site on the Tonopah Test Range in Nevada was studied in a series of experiments. For each experiment, or trial, rumen contents collected from a fistulated steer or a normal animals at the time of sacrifice were incubated in simulated bovine gastrointestinal fluids, and the solubility of plutonium and americium was analyzed following the abomasal, duodenal, jejunal, and lower intestinal digestive states. For Area 13, the peak plutonium-238 solubilities ranged from 1.09 to 9.60 percent for animals grazing in the inner enclosure that surrounds ground zero (GZ); for animals grazing in the outer enclosure, the peaks ranged from 1.86 to 18.46%. The peak plutonium-239 solubilities ranged from 0.71 to 4.81% for animals from the inner enclosure and from 0.71 to 3.61% for animals from the outer enclosure. Plutonium-238 was generally more soluble than plutonium-239. Plutonium ingested by cattle grazing in the outer enclosure was usually more soluble than plutonium ingested by cattle grazing in the inner enclosure. The highest concentrations of plutonium in the rumen contents of cattle grazing in the inner enclosure were found in trials conducted during August and November 1975 and January 1976. These concentrations decreased during the February, May, and July 1976 trials. The decrease was followed by an increase in plutonium concentration during the November 1976 trial. The concentration of americium-241 followed the same trend. 13 references, 13 tables

  19. Ion Beam Extraction by Discrete Ion Focusing

    DEFF Research Database (Denmark)

    2010-01-01

    An apparatus (900) and methods are disclosed for ion beam extraction. In an implementation, the apparatus includes a plasma source (or plasma) (802) and an ion extractor (804). The plasma source is adapted to generate ions and the ion extractor is immersed in the plasma source to extract a fracti...

  20. ION GUN

    Science.gov (United States)

    Dandl, R.A.

    1961-10-24

    An ion gun is described for the production of an electrically neutral ionized plasma. The ion gun comprises an anode and a cathode mounted in concentric relationship with a narrow annulus between. The facing surfaces of the rear portions of the anode and cathode are recessed to form an annular manifold. Positioned within this manifold is an annular intermediate electrode aligned with the an nulus between the anode and cathode. Gas is fed to the manifold and an arc discharge is established between the anode and cathode. The gas is then withdrawn from the manifold through the annulus between the anode and cathode by a pressure differential. The gas is then ionized by the arc discharge across the annulus. The ionized gas is withdrawn from the annulus by the combined effects of the pressure differential and a collimating magnetic field. In a 3000 gauss magnetic field, an arc voltage of 1800 volts, and an arc current of 0.2 amp, a plasma of about 3 x 10/sup 11/ particles/cc is obtained. (AEC)

  1. Heavy ions

    CERN Multimedia

    CERN. Geneva; Antinori, Federico

    2001-01-01

    Colliding two heavy nuclei at ultrarelativistic energies allows to create in the laboratory a bulk system with huge density, pressure and temperature and to study its properties. It is estimated that in Pb-Pb collisions at CERN-SPS we reach over an appreciable volume an energy density which exceeds by more than a factor 20 that of normal nuclear matter. At such densities, the hadrons are so closely packed that they interpenetrate; novel physics phenomena are expected to appear. QCD predicts that under such conditions a phase transition from a system composed of colourless hadrons to a Quark-Gluon Plasma (QGP) should occur. A rich ultrarelativistic heavy-ion physics programme is under way both at BNL-AGS and at CERN-SPS since 1986. The results obtained so far have led CERN to officially announce evidence for a new state of matter last year. A long-range programme of heavy-ion physics at higher energies is under way (BNL-RHIC) and in preparation (CERN-LHC). These lectures are meant as an introduction to the phy...

  2. Heavy ions

    CERN Multimedia

    CERN. Geneva. Audiovisual Unit

    2002-01-01

    Colliding two heavy nuclei at ultrarelativistic energies allows to create in the laboratory a bulk system with huge density, pressure and temperature and to study its properties. It is estimated that in Pb-Pb collisions at CERN-SPS we reach over an appreciable volume an energy density which exceeds by more than a factor 20 that of normal nuclear matter. At such densities, the hadrons are so closely packed that they interpenetrate; novel physics phenomena are expected to appear. QCD predicts that under such conditions a phase transition from a system composed of colourless hadrons to a Quark-Gluon Plasma (QGP) should occur. A rich ultrarelativistic heavy-ion physics programme is under way both at BNL-AGS and at CERN-SPS since 1986. The results obtained so far have led CERN to officially announce evidence for a new state of matter last year. A long-range programme of heavy-ion physics at higher energies is under way (BNL-RHIC) and in preparation (CERN-LHC). These lectures are meant as an introduction to the phy...

  3. Separation by sequential chromatography of americium, plutonium and neptunium elements: application to the study of trans-uranian elements migration in a European lacustrine system

    International Nuclear Information System (INIS)

    Michel, H.

    1999-01-01

    The nuclear tests carried out in the atmosphere in the Sixties, the accidents and in particular that to the power station of Chernobyl in 1986, were at the origin of the dispersion of a significant quantity of transuranic elements and fission products. The study of a lake system, such that of the Blelham Tarn in Great Britain, presented in this memory, can bring interesting answers to the problems of management of the environment. The determination of the radionuclides in sediment cores made it possible not only to establish the history of the depositions and consequently the origin of the radionuclides, but also to evaluate the various transfers which took place according to the parameters of the site and the properties of the elements. The studied transuranic elements are plutonium 238, 239-240, americium 241 and neptunium 237. Alpha emitting radionuclides, their determination requires complex radiochemical separations. A method was worked out to successively separate the three radioelements by using a same chromatographic column. Cesium 137 is the studied fission product, its determination is done by direct Gamma spectrometry. Lead 210, natural radionuclide, whose atmospheric flow can be supposed constant. makes it possible to obtain a chronology of the various events. The detailed vertical study of sediment cores showed that the accumulation mode of the studied elements is the same one and that the methods of dating converge. The cesium, more mobile than transuranic elements in the atmosphere, was detected in the 1963 and 1986 fallout whereas an activity out of transuranic elements appears only for the 1963 fallout. The activity of the 1963 cesium fallout is of the same order of magnitude as that of 1986. The calculation of the diffusion coefficients of the elements in the sediments shows an increased migration of cesium compared to transuranic elements. An inventory on the whole of the lake made it possible to note that the atmospheric fallout constitute the

  4. Fabrication of targets for transmutation of americium : synthesis of inertial matrix by sol-gel method. Procedure study on the infiltration of a radioactive solutions

    International Nuclear Information System (INIS)

    Fernandez Carretero, A.

    2002-01-01

    addition a new and unexpected phase formed by the reaction of americium with spinel during the high temperature synthesis process has been identified. This new phase could provide a unique menas to stabilise Am in one particular oxidation state. (Author)

  5. Ion beam monitoring

    International Nuclear Information System (INIS)

    McKinney, C.R.

    1980-01-01

    An ion beam analyzer is specified, having an ion source for generating ions of a sample to be analyzed, means for extracting the sample ions, means for focusing the sample ions into a beam, separation means positioned along the ion beam for selectively deflecting species of ions, and means for detecting the selected species of ions. According to the specification, the analyzer further comprises (a) means for disabling at least a portion of the separation means, such that the ion beam from the source remains undeflected; (b) means located along the path of the undeflected ion beam for sensing the sample ions; and (c) enabling means responsive to the sensing means for automatically re-enabling the separation means when the sample ions reach a predetermined intensity level. (author)

  6. Recoil ion spectroscopy with heavy ions

    International Nuclear Information System (INIS)

    Beyer, H.F.; Mann, R.

    1984-01-01

    This chapter examines the production of very high charge state ions in single ion-atom collisions. Topics considered include some aspects of highly ionized atoms, experimental approaches, the production of highly charged target ions (monoatomic targets, recoil energy distribution, molecular fragmentation, outer-shell rearrangement, lifetime measurements, a comparison of projectile-, target-, and plasma-ion stripping), and secondary collision experiments (selective electron capture, potential applications). The heavy-ion beams for the described experiments were provided by accelerators such as tandem Van de Graaff facility and the UNILAC

  7. Surface negative ion production in ion sources

    International Nuclear Information System (INIS)

    Belchenko, Y.

    1993-01-01

    Negative ion sources and the mechanisms for negative ion production are reviewed. Several classes of sources with surface origin of negative ions are examined in detail: surface-plasma sources where ion production occurs on the electrode in contact with the plasma, and ''pure surface'' sources where ion production occurs due to conversion or desorption processes. Negative ion production by backscattering, impact desorption, and electron- and photo-stimulated desorption are discussed. The experimental efficiencies of intense surface negative ion production realized on electrodes contacted with hydrogen-cesium or pure hydrogen gas-discharge plasma are compared. Recent modifications of surface-plasma sources developed for accelerator and fusion applications are reviewed in detail

  8. Gas phase ion chemistry

    CERN Document Server

    Bowers, Michael T

    1979-01-01

    Gas Phase Ion Chemistry, Volume 1 covers papers on the advances of gas phase ion chemistry. The book discusses the advances in flow tubes and the measurement of ion-molecule rate coefficients and product distributions; the ion chemistry of the earth's atmosphere; and the classical ion-molecule collision theory. The text also describes statistical methods in reaction dynamics; the state selection by photoion-photoelectron coincidence; and the effects of temperature and pressure in the kinetics of ion-molecule reactions. The energy distribution in the unimolecular decomposition of ions, as well

  9. Dialkyldithiophosphoric acids - chemical properties and 5f and 4f elements ions extraction

    International Nuclear Information System (INIS)

    Pattee, D.

    1987-09-01

    This work is a contribution to the study of the properties of the dialkyldithiophosphoric acids and of the extraction of the 4f and 5f ions from weakly acidic nitrate and phosphate media. Following a complete bibliographic study, synthesis and purification of the di-2-ethylhexyl-dithiophosphoric acid (HDEHDTP) is studied. It is identified with chemical methods and spectroscopic methods (I.R., N.M.R., V.P.C.); its by products, the di-2-ethylhexyl (monothio) phosphoric acids (HDEHTP, HDEHP) are also identified and characterized. Stability against hydrolysis and radiolysis is determined. The extractive properties are studied for the 4f and 5f ions. The presence of a sulfur donor atom in HDEHDTP makes it inefficient for the extraction of trivalent lanthanides and actinides but brings out a certain selectivity for americium. For HDEHTP, the presence of an oxygen donor atom rubs out any selectivity and the extraction constants are greater. Selectivity of HDEHDTP is increased by TBP (tri-n-butylphosphate) in synergistic mixtures. The mechanism of extraction of hexavalent uranium from phosphoric medium is elucidated. A model is developed by NMR for the micellisation of the sodium salts of HDEHDTP, HDEHTP and HDEHP, and extrapolated it to the trivalent rare earth salts of the acids. The structures are verified by light scattering and low angle X-ray diffraction [fr

  10. Laser ion sources

    Energy Technology Data Exchange (ETDEWEB)

    Bykovskij, Yu

    1979-02-01

    The characteristics a laser source of multiply-ionized ions are described with regard to the interaction of laser radiation and matter, ion energy spectrum, angular ion distribution. The amount of multiple-ionization ions is evaluated. Out of laser source applications a laser injector of multiple-ionization ions and nuclei, laser mass spectrometry, laser X-ray microradiography, and a laser neutron generators are described.

  11. Americium behaviour in plastic vessels

    International Nuclear Information System (INIS)

    Legarda, F.; Herranz, M.; Idoeta, R.; Abelairas, A.

    2010-01-01

    The adsorption of 241 Am dissolved in water in different plastic storage vessels was determined. Three different plastics were investigated with natural and distilled waters and the retention of 241 Am by these plastics was studied. The same was done by varying vessel agitation time, vessel agitation speed, surface/volume ratio of water in the vessels and water pH. Adsorptions were measured to be between 0% and 70%. The adsorption of 241 Am is minimized with no water agitation, with PET or PVC plastics, and by water acidification.

  12. Phonon properties of americium phosphide

    Energy Technology Data Exchange (ETDEWEB)

    Arya, B. S., E-mail: bsarya13@yahoo.com [Department of Physics, Govt. Narmada P G College, Hoshangabad -461001 (India); Aynyas, Mahendra [Department of Physics, C. S. A. Govt. P. G. College Sehore-46601 (India); Sanyal, S. P. [Department of Physics, Barkatullah University, Bhopal-462026 (India)

    2016-05-23

    Phonon properties of AmP have been studied by using breathing shell models (BSM) which includes breathing motion of electrons of the Am atoms due to f-d hybridization. The phonon dispersion curves, specific heat calculated from present model. The calculated phonon dispersion curves of AmP are presented follow the same trend as observed in uranium phosphide. We discuss the significance of this approach in predicting the phonon dispersion curves of these compounds and examine the role of electron-phonon interaction.

  13. Americium behaviour in plastic vessels

    Energy Technology Data Exchange (ETDEWEB)

    Legarda, F.; Herranz, M. [Departamento de Ingenieria Nuclear y Mecanica de Fluidos, Escuela Tecnica Superior de Ingenieria de Bilbao, Universidad del Pais Vasco (UPV/EHU), Alameda de Urquijo s/n, 48013 Bilbao (Spain); Idoeta, R., E-mail: raquel.idoeta@ehu.e [Departamento de Ingenieria Nuclear y Mecanica de Fluidos, Escuela Tecnica Superior de Ingenieria de Bilbao, Universidad del Pais Vasco (UPV/EHU), Alameda de Urquijo s/n, 48013 Bilbao (Spain); Abelairas, A. [Departamento de Ingenieria Nuclear y Mecanica de Fluidos, Escuela Tecnica Superior de Ingenieria de Bilbao, Universidad del Pais Vasco (UPV/EHU), Alameda de Urquijo s/n, 48013 Bilbao (Spain)

    2010-07-15

    The adsorption of {sup 241}Am dissolved in water in different plastic storage vessels was determined. Three different plastics were investigated with natural and distilled waters and the retention of {sup 241}Am by these plastics was studied. The same was done by varying vessel agitation time, vessel agitation speed, surface/volume ratio of water in the vessels and water pH. Adsorptions were measured to be between 0% and 70%. The adsorption of {sup 241}Am is minimized with no water agitation, with PET or PVC plastics, and by water acidification.

  14. Americium behaviour in plastic vessels.

    Science.gov (United States)

    Legarda, F; Herranz, M; Idoeta, R; Abelairas, A

    2010-01-01

    The adsorption of (241)Am dissolved in water in different plastic storage vessels was determined. Three different plastics were investigated with natural and distilled waters and the retention of (241)Am by these plastics was studied. The same was done by varying vessel agitation time, vessel agitation speed, surface/volume ratio of water in the vessels and water pH. Adsorptions were measured to be between 0% and 70%. The adsorption of (241)Am is minimized with no water agitation, with PET or PVC plastics, and by water acidification. Copyright 2009 Elsevier Ltd. All rights reserved.

  15. Ion Beam Propulsion Study

    Science.gov (United States)

    2008-01-01

    The Ion Beam Propulsion Study was a joint high-level study between the Applied Physics Laboratory operated by NASA and ASRC Aerospace at Kennedy Space Center, Florida, and Berkeley Scientific, Berkeley, California. The results were promising and suggested that work should continue if future funding becomes available. The application of ion thrusters for spacecraft propulsion is limited to quite modest ion sources with similarly modest ion beam parameters because of the mass penalty associated with the ion source and its power supply system. Also, the ion source technology has not been able to provide very high-power ion beams. Small ion beam propulsion systems were used with considerable success. Ion propulsion systems brought into practice use an onboard ion source to form an energetic ion beam, typically Xe+ ions, as the propellant. Such systems were used for steering and correction of telecommunication satellites and as the main thruster for the Deep Space 1 demonstration mission. In recent years, "giant" ion sources were developed for the controlled-fusion research effort worldwide, with beam parameters many orders of magnitude greater than the tiny ones of conventional space thruster application. The advent of such huge ion beam sources and the need for advanced propulsion systems for exploration of the solar system suggest a fresh look at ion beam propulsion, now with the giant fusion sources in mind.

  16. EURADOS action for determination of americium in skull measures in vivo and Monte Carlo simulation; Accion EURADOS para la determinacion de americio en craneo mediante medidas in-vivo y simulacion Monte Carlo

    Energy Technology Data Exchange (ETDEWEB)

    Lopez Ponte, M. A.; Navarro Amaro, J. F.; Perez Lopez, B.; Navarro Bravo, T.; Nogueira, P.; Vrba, T.

    2013-07-01

    From the Group of WG7 internal dosimetry of the EURADOS Organization (European Radiation Dosimetry group, e.V.) which It coordinates CIEMAT, international action for the vivo measurement of americium has been conducted in three mannequins type skull with detectors of Germanium by gamma spectrometry and simulation by Monte Carlo methods. Such action has been raised as two separate exercises, with the participation of institutions in Europe, America and Asia. Other actions similar precede this vivo intercomparison of measurement and modeling Monte Carlo1. The preliminary results and associated findings are presented in this work. The laboratory of the body radioactivity (CRC) of service counter of dosimetry staff internal (DPI) of the CIEMAT, it has been one of the participants in vivo measures exercise. On the other hand part, the Group of numerical dosimetry of CIEMAT is participant of the Monte Carlo2 simulation exercise. (Author)

  17. Negative ion sources

    International Nuclear Information System (INIS)

    Ishikawa, Junzo; Takagi, Toshinori

    1983-01-01

    Negative ion sources have been originally developed at the request of tandem electrostatic accelerators, and hundreds of nA to several μA negative ion current has been obtained so far for various elements. Recently, the development of large current hydrogen negative ion sources has been demanded from the standpoint of the heating by neutral particle beam injection in nuclear fusion reactors. On the other hand, the physical properties of negative ions are interesting in the thin film formation using ions. Anyway, it is the present status that the mechanism of negative ion action has not been so fully investigated as positive ions because the history of negative ion sources is short. In this report, the many mechanisms about the generation of negative ions proposed so far are described about negative ion generating mechanism, negative ion source plasma, and negative ion generation on metal surfaces. As a result, negative ion sources are roughly divided into two schemes, plasma extraction and secondary ion extraction, and the former is further classified into the PIG ion source and its variation and Duoplasmatron and its variation; while the latter into reflecting and sputtering types. In the second half of the report, the practical negative ion sources of each scheme are described. If the mechanism of negative ion generation will be investigated more in detail and the development will be continued under the unified know-how as negative ion sources in future, the development of negative ion sources with which large current can be obtained for any element is expected. (Wakatsuki, Y.)

  18. Critical and shielding parametric studies with the Monte Carlo code TRIPOLI to identify the key points to take into account during the transportation of blanket assemblies with high ratio of americium

    International Nuclear Information System (INIS)

    Gosmain, Cecile-Aline

    2011-01-01

    In the framework of French research program on Generation IV sodium cooled fast reactor, one possible option consists in burning minor actinides in this kind of Advanced Sodium Technological Reactor. Two types of transmutation mode are studied in the world : the homogeneous mode of transmutation where actinides are scattered with very low enrichment ratio in fissile assemblies and the heterogeneous mode where fissile core is surrounded by blanket assemblies filled with minor actinides with ratio of incorporated actinides up to 20%. Depending on which element is considered to be burnt and on its content, these minor actinides contents imply constraints on assemblies' transportation between Nuclear Power Plants and fuel cycle facilities. In this study, we present some academic studies in order to identify some key constraints linked to the residual power and neutron/gamma load of such kind of blanket assemblies. To simplify the approach, we considered a modeling of a 'model cask' dedicated to the transportation of a unique irradiated blanket assembly loaded with 20% of Americium and basically inspired from an existent cask designed initially for the damaged fissile Superphenix assembly transport. Thermal calculations performed with EDF-SYRTHES code have shown that due to thermal limitations on cladding temperature, the decay time to be considered before transportation is 20 years. This study is based on explicit 3D representations of the cask and the contained blanket assembly with the Monte Carlo code TRIPOLI/JEFF3.1.1 library and concludes that after such a decay time, the transportation of a unique Americium radial blanket is feasible only if the design of our model cask is modified in order to comply with the dose limitation criterion. (author)

  19. Ion sources for heavy ion fusion

    International Nuclear Information System (INIS)

    Yu, S.S.; Eylon, S.; Chupp, W.

    1995-09-01

    The development of ion sources for heavy ion fusion will be reported with particular emphasis on a recently built 2 MV injector. The new injector is based on an electrostatic quadrupole configuration, and has produced pulsed K + ions of 950 mA peak from a 6.7 inch curved alumino silicate source. The ion beam has reached 2.3 MV with an energy flatness of ±0.2% over 1 micros. The measured normalized edge emittance of less than 1 π mm-mr is close to the source temperature limit. The design, construction, performance, and comparisons with three-dimensional particle-in-cell simulations will be described

  20. Electron Beam Ion Sources

    CERN Document Server

    Zschornacka, G.; Thorn, A.

    2013-12-16

    Electron beam ion sources (EBISs) are ion sources that work based on the principle of electron impact ionization, allowing the production of very highly charged ions. The ions produced can be extracted as a DC ion beam as well as ion pulses of different time structures. In comparison to most of the other known ion sources, EBISs feature ion beams with very good beam emittances and a low energy spread. Furthermore, EBISs are excellent sources of photons (X-rays, ultraviolet, extreme ultraviolet, visible light) from highly charged ions. This chapter gives an overview of EBIS physics, the principle of operation, and the known technical solutions. Using examples, the performance of EBISs as well as their applications in various fields of basic research, technology and medicine are discussed.

  1. Actinide production in the reaction of heavy ions with curium-248

    International Nuclear Information System (INIS)

    Moody, K.J.

    1983-07-01

    Chemical experiments were performed to examine the usefulness of heavy ion transfer reactions in producing new, neutron-rich actinide nuclides. A general quasi-elastic to deep-inelastic mechanism is proposed, and the utility of this method as opposed to other methods (e.g. complete fusion) is discussed. The relative merits of various techniques of actinide target synthesis are discussed. A description is given of a target system designed to remove the large amounts of heat generated by the passage of a heavy ion beam through matter, thereby maximizing the beam intensity which can be safely used in an experiment. Also described is a general separation scheme for the actinide elements from protactinium (Z=91) to mendelevium (Z=101), and fast specific procedures for plutonium, americium and berkelium. The cross sections for the production of several nuclides from the bombardment of 248 Cm with 18 O, 86 Kr and 136 Xe projectiles at several energies near and below the Coulomb barrier were determined. The results are compared with yields from 48 Ca and 238 U bombardments of 248 Cm. Simple extrapolation of the product yields into unknown regions of charge and mass indicates that the use of heavy ion transfer reactions to produce new, neutron-rich above-target species is limited. The substantial production of neutron-rich below-target species, however, indicates that with very heavy ions like 136 Xe and 238 U the new species 248 Am, 249 Am and 247 Pu should be produced with large cross sections from a 248 Cm target. A preliminary, unsuccessful attempt to isolate 247 Pu is outlined. The failure is probably due to the half life of the decay, which is calculated to be less than 3 minutes. The absolute gamma ray intensities from 251 Bk decay, necessary for calculating the 251 Bk cross section, are also determined

  2. Ions and light

    CERN Document Server

    Bowers, Michael T

    2013-01-01

    Gas Phase Ion Chemistry, Volume 3: Ions and Light discusses how ions are formed by electron impact, ion-molecule reactions, or electrical discharge. This book discusses the use of light emitted by excited molecules to characterize either the chemistry that formed the excited ion, the structure of the excited ion, or both.Organized into 10 chapters, this volume begins with an overview of the extension of the classical flowing afterglow technique to include infrared and chemiluminescence and laser-induced fluorescence detection. This text then examines the experiments involving molecules that ar

  3. Negative-ion states

    International Nuclear Information System (INIS)

    Compton, R.N.

    1982-01-01

    In this brief review, we discuss some of the properties of atomic and molecular negative ions and their excited states. Experiments involving photon reactions with negative ions and polar dissociation are summarized. 116 references, 14 figures

  4. Quadrupole Ion Traps

    Indian Academy of Sciences (India)

    to do precision spectroscopic measurements on these ions. ... Bonn, investigated the non-magnetic quadrupole mass filter, .... the details of which will be discussed in the subse- ... the radial plane the ion undergoes a circular motion with the.

  5. Negative ion detachment processes

    International Nuclear Information System (INIS)

    Champion, R.L.; Doverspike, L.D.

    1990-10-01

    This paper discusses the following topics: H - and D - collisions with atomic hydrogen; collisional decomposition of SF 6 - ; two-electron loss processes in negative ion collisions; associative electron detachment; and negative ion desorption from surfaces

  6. Ion sources in AMS

    International Nuclear Information System (INIS)

    Iyer, Indira S.

    1997-01-01

    Accelerator Mass Spectrometry (AMS) entails the sputtering of various samples in an ion source followed by high precision mass analysis of the sputtered ion species in a Tandem Electrostatic Accelerator. A brief account is given

  7. Single Cathode Ion Thruster

    Data.gov (United States)

    National Aeronautics and Space Administration — Objective is to design an electrostatic ion thruster that is more efficient, simpler, and lower cost than the current gridded ion thruster. Initial objective is to...

  8. Applications of decelerated ions

    International Nuclear Information System (INIS)

    Johnson, B.M.

    1985-03-01

    Many facilities whose sole purpose had been to accelerate ion beams are now becoming decelerators as well. The development and current status of accel-decel operations is reviewed here. Applications of decelerated ions in atomic physics experiments are discussed

  9. Fundamentals of ion exchange

    International Nuclear Information System (INIS)

    Townsend, R.P.

    1993-01-01

    In this paper the fundamentals of ion exchange mechanisms and their thermodynamics are described. A range of ion exchange materials is considered and problems of communication and technology transfer between scientists working in the field are discussed. (UK)

  10. Gas phase ion chemistry

    CERN Document Server

    Bowers, Michael T

    1979-01-01

    Gas Phase Ion Chemistry, Volume 2 covers the advances in gas phase ion chemistry. The book discusses the stabilities of positive ions from equilibrium gas-phase basicity measurements; the experimental methods used to determine molecular electron affinities, specifically photoelectron spectroscopy, photodetachment spectroscopy, charge transfer, and collisional ionization; and the gas-phase acidity scale. The text also describes the basis of the technique of chemical ionization mass spectrometry; the energetics and mechanisms of unimolecular reactions of positive ions; and the photodissociation

  11. Ion mobility spectrometry

    CERN Document Server

    Eiceman, GA

    2005-01-01

    Key Developments for Faster, More Precise Detection Capabilities Driven by the demand for the rapid and advanced detection of explosives, chemical and biological warfare agents, and narcotics, ion mobility spectrometry (IMS) undergone significant refinements in technology, computational capabilities, and understanding of the principles of gas phase ion chemistry and mobility. Beginning with a thorough discussion of the fundamental theories and physics of ion mobility, Ion Mobility Spectrometry, Second Edition describes the recent advances in instrumentation and newly

  12. Intense ion beam generator

    International Nuclear Information System (INIS)

    Humphries, S. Jr.; Sudan, R.N.

    1977-01-01

    Methods and apparatus for producing intense megavolt ion beams are disclosed. In one embodiment, a reflex triode-type pulsed ion accelerator is described which produces ion pulses of more than 5 kiloamperes current with a peak energy of 3 MeV. In other embodiments, the device is constructed so as to focus the beam of ions for high concentration and ease of extraction, and magnetic insulation is provided to increase the efficiency of operation

  13. Ion sources for accelerators

    International Nuclear Information System (INIS)

    Alton, G.D.

    1974-01-01

    A limited review of low charge sate positive and negative ion sources suitable for accelerator use is given. A brief discussion is also given of the concepts underlying the formation and extraction of ion beams. Particular emphasis is placed on the technology of ion sources which use solid elemental or molecular compounds to produce vapor for the ionization process

  14. Negative Ion Density Fronts

    International Nuclear Information System (INIS)

    Igor Kaganovich

    2000-01-01

    Negative ions tend to stratify in electronegative plasmas with hot electrons (electron temperature Te much larger than ion temperature Ti, Te > Ti ). The boundary separating a plasma containing negative ions, and a plasma, without negative ions, is usually thin, so that the negative ion density falls rapidly to zero-forming a negative ion density front. We review theoretical, experimental and numerical results giving the spatio-temporal evolution of negative ion density fronts during plasma ignition, the steady state, and extinction (afterglow). During plasma ignition, negative ion fronts are the result of the break of smooth plasma density profiles during nonlinear convection. In a steady-state plasma, the fronts are boundary layers with steepening of ion density profiles due to nonlinear convection also. But during plasma extinction, the ion fronts are of a completely different nature. Negative ions diffuse freely in the plasma core (no convection), whereas the negative ion front propagates towards the chamber walls with a nearly constant velocity. The concept of fronts turns out to be very effective in analysis of plasma density profile evolution in strongly non-isothermal plasmas

  15. Nanostructures by ion beams

    Science.gov (United States)

    Schmidt, B.

    Ion beam techniques, including conventional broad beam ion implantation, ion beam synthesis and ion irradiation of thin layers, as well as local ion implantation with fine-focused ion beams have been applied in different fields of micro- and nanotechnology. The ion beam synthesis of nanoparticles in high-dose ion-implanted solids is explained as phase separation of nanostructures from a super-saturated solid state through precipitation and Ostwald ripening during subsequent thermal treatment of the ion-implanted samples. A special topic will be addressed to self-organization processes of nanoparticles during ion irradiation of flat and curved solid-state interfaces. As an example of silicon nanocrystal application, the fabrication of silicon nanocrystal non-volatile memories will be described. Finally, the fabrication possibilities of nanostructures, such as nanowires and chains of nanoparticles (e.g. CoSi2), by ion beam synthesis using a focused Co+ ion beam will be demonstrated and possible applications will be mentioned.

  16. Enhanced ion acoustic fluctuations and ion outflows

    Directory of Open Access Journals (Sweden)

    F. R. E. Forme

    1999-02-01

    Full Text Available A number of observations showing enhanced ion acoustic echoes observed by means of incoherent scatter radars have been reported in the literature. The received power is extremely enhanced by up to 1 or 2 orders of magnitude above usual values, and it is mostly contained in one of the two ion acoustic lines. This spectral asymmetry and the intensity of the received signal cannot be resolved by the standard analysis procedure and often causes its failure. As a result, and in spite of a very clear spectral signature, the analysis is unable to fit the plasma parameters inside the regions of ion acoustic turbulence. We present European Incoherent Scatter radar (EISCAT observations of large ion outflows associated with the simultaneous occurrence of enhanced ion acoustic echoes. The ion fluxes can reach 1014 m-2 s-1 at 800 km altitude. From the very clear spectral signatures of these echoes, a method is presented to extract estimates of the electron temperature and the ion drift within the turbulent regions. It is shown that the electron gas is strongly heated up to 11 000 K. Also electron temperature gradients of about 0.02 K/m exist. Finally, the estimates of the electron temperature and of the ion drift are used to study the possible implications for the plasma transport inside turbulent regions. It is shown that strong electron temperature gradients cause enhancement of the ambipolar electric field and can account for the observed ion outflows.Key words. Ionosphere (auroral ionosphere; ionosphere · magnetosphere interactions; plasma waves and instabilities.

  17. Vacuum Arc Ion Sources

    CERN Document Server

    Brown, I.

    2013-12-16

    The vacuum arc ion source has evolved into a more or less standard laboratory tool for the production of high-current beams of metal ions, and is now used in a number of different embodiments at many laboratories around the world. Applications include primarily ion implantation for material surface modification research, and good performance has been obtained for the injection of high-current beams of heavy-metal ions, in particular uranium, into particle accelerators. As the use of the source has grown, so also have the operational characteristics been improved in a variety of different ways. Here we review the principles, design, and performance of vacuum arc ion sources.

  18. Improved sample utilization in thermal ionization mass spectrometry isotope ratio measurements: refined development of porous ion emitters for nuclear forensic applications

    Energy Technology Data Exchange (ETDEWEB)

    Baruzzini, Matthew Louis [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-05-08

    The precise and accurate determination of isotopic composition in nuclear forensic samples is vital for assessing origin, intended use and process history. Thermal ionization mass spectrometry (TIMS) is widely accepted as the gold standard for high performance isotopic measurements and has long served as the workhorse in the isotopic ratio determination of nuclear materials. Nuclear forensic and safeguard specialists have relied heavily on such methods for both routine and atypical e orts. Despite widespread use, TIMS methods for the assay of actinide systems continue to be hindered by poor ionization e ciency, often less than tenths of a percent; the majority of a sample is not measured. This represents a growing challenge in addressing nextgeneration nuclear detection needs by limiting the ability to analyze ultratrace quantities of high priority elements that could potentially provide critical nuclear forensic signatures. Porous ion emitter (PIE) thermal ion sources were developed in response to the growing need for new TIMS ion source strategies for improved ionization e ciency, PIEs have proven to be simple to implement, straightforward approach to boosting ion yield. This work serves to expand the use of PIE techniques for the analysis of trace quantities of plutonium and americium. PIEs exhibited superior plutonium and americium ion yields when compared to direct lament loading and the resin bead technique, one of the most e cient methods for actinide analysis, at similar mass loading levels. Initial attempts at altering PIE composition for the analysis of plutonium proved to enhance sample utilization even further. Preliminary investigations of the instrumental fractionation behavior of plutonium and uranium analyzed via PIE methods were conducted. Data collected during these initial trial indicate that PIEs fractionate in a consistent, reproducible manner; a necessity for high precision isotope ratio measurements. Ultimately, PIEs methods were applied for

  19. Heavy-ion radiography

    International Nuclear Information System (INIS)

    Fabrikant, J.I.; Tobias, C.A.; Holley, W.R.; Benton, E.V.; Woodruff, K.H.; MacFarland, E.W.

    1983-01-01

    High energy, heavy-ion beams offer superior discrimination of tissue electron densities at very low radiation doses. This characteristic has potential for diagnostic medical imaging of neoplasms arising in the soft tissues and organs because it can detect smaller inhomogeneities than x rays. Heavy-ion imaging may also increase the accuracy of cancer radiotherapy planning involving use of accelerated charged particles. In the current physics research program of passive heavy-ion imaging, critical modulation transfer function tests are being carried out in heavy-ion projection radiography and heavy-ion computerized tomography. The research goal is to improve the heavy-ion imaging method until it reaches the limits of its theoretical resolution defined by range straggling, multiple scattering, and other factors involved in the beam quality characteristics. Clinical uses of the imaging method include the application of heavy-ion computerized tomography to heavy-ion radiotherapy planning, to the study of brain tumors and other structures of the head, and to low-dose heavy-ion projection mammography, particularly for women with dense breasts where other methods of diagnosis fail. The ions used are primarily 300 to 570 MeV/amu carbon and neon ions accelerated at the Lawrence Berkeley Laboratory Bevalac

  20. Ion implantation into iron

    International Nuclear Information System (INIS)

    Iwaki, Masaya

    1978-01-01

    The distribution of implanted ions in iron, the friction characteristics and the corrosion of iron were studied. The distribution of Ni or Cr ions implanted into mild steel was measured. The accelerated voltage was 150 keV, and the beam current density was about 2 microampere/cm 2 . The measurement was made with an ion microanalyzer. The measured distribution was compared with that of LSS theory. Deep invasion of Ni was seen in the measured distribution. The distribution of Cr ions was different from the distribution calculated by the LSS theory. The relative friction coefficient of mild steel varied according to the dose of implanted Cu or N ions, and to the accelerating voltage. Formation of compound metals on the surfaces of metals by ion-implantation was investigated for the purpose to prevent the corrosion of metals. The resistance of mild steel in which Ni ions were implanted was larger than that of mild steel without any treatment. (Kato, T.)

  1. Crater formation by single ions, cluster ions and ion "showers"

    CERN Document Server

    Djurabekova, Flyura; Timko, Helga; Nordlund, Kai; Calatroni, Sergio; Taborelli, Mauro; Wuensch, Walter

    2011-01-01

    The various craters formed by giant objects, macroscopic collisions and nanoscale impacts exhibit an intriguing resemblance in shapes. At the same time, the arc plasma built up in the presence of sufficiently high electric fields at close look causes very similar damage on the surfaces. Although the plasma–wall interaction is far from a single heavy ion impact over dense metal surfaces or the one of a cluster ion, the craters seen on metal surfaces after a plasma discharge make it possible to link this event to the known mechanisms of the crater formations. During the plasma discharge in a high electric field the surface is subject to high fluxes (~1025 cm-2s-1) of ions with roughly equal energies typically of the order of a few keV. To simulate such a process it is possible to use a cloud of ions of the same energy. In the present work we follow the effect of such a flux of ions impinging the surface in the ‘‘shower’’ manner, to find the transition between the different mechanisms of crater formati...

  2. Optical effects of ion implantation

    International Nuclear Information System (INIS)

    Townsend, P.D.

    1987-01-01

    The review concerns the effects of ion implantation that specifically relate to the optical properties of insulators. Topics which are reviewed include: ion implantation, ion range and damage distributions, colour centre production by ion implantation, high dose ion implantation, and applications for integrated optics. Numerous examples are presented of both diagnostic and industrial examples of ion implantation effects in insulators. (U.K.)

  3. Ion beam stabilization in ion implantation equipment

    International Nuclear Information System (INIS)

    Pina, L.

    1973-01-01

    The results are presented of experimental efforts aimed at ion beam current stabilization in an equipment for ion implantation in solids. The related problems of power supplies are discussed. Measured characteristics of laboratory equipment served the determination of the parameters to be required of the supplies as well as the design and the construction of the supplies. The respective wiring diagram is presented. (J.K.)

  4. Calculation of ion storage in electron beams with account of ion-ion interactions

    International Nuclear Information System (INIS)

    Perel'shtejn, Eh.A.; Shirkov, G.D.

    1979-01-01

    Ion storage in relativistic electron beams was calculated taking account of ion-ion charge exchange and ionization. The calculations were made for nitrogen ion storage from residual gas during the compression of electron rings in the adhezator of the JINR heavy ion accelerator. The calculations were made for rings of various parameters and for various pressures of the residual gas. The results are compared with analogous calculations made without account of ion-ion processes. It is shown that at heavy loading of a ring by ions ion-ion collisions play a significant part, and they should be taken into account while calculating ion storage

  5. Duopigatron ion source studies

    International Nuclear Information System (INIS)

    Bacon, F.M.; Bickes, R.W. Jr.; O'Hagan, J.B.

    1978-07-01

    Ion source performance characteristics consisting of total ion current, ion energy distribution, mass distribution, and ion current density distribution were measured for several models of a duopigatron. Variations on the duopigatron design involved plasma expansion cup material and dimensions, secondary cathode material, and interelectrode spacings. Of the designs tested, the one with a copper and molybdenum secondary cathode and a mild steel plasma expansion cup proved to give the best results. The ion current density distribution was peaked at the center of the plasma expansion cup and fell off to 80 percent of the peak value at the cup wall for a cup 15.2 mm deep. A total ion current of 180 mA consisting of 60 to 70 percent atomic ions was produced with an arc current of 20 A and source pressure of 9.3 Pa. More shallow cups produced a larger beam current and a more sharply peaked ion current density distribution. Typical ion energy distributions were bell-shaped curves with a peak 10 to 20 V below anode potential and with ion energies extending 30 to 40 V on either side of the peak

  6. Quantitative ion implantation

    International Nuclear Information System (INIS)

    Gries, W.H.

    1976-06-01

    This is a report of the study of the implantation of heavy ions at medium keV-energies into electrically conducting mono-elemental solids, at ion doses too small to cause significant loss of the implanted ions by resputtering. The study has been undertaken to investigate the possibility of accurate portioning of matter in submicrogram quantities, with some specific applications in mind. The problem is extensively investigated both on a theoretical level and in practice. A mathematical model is developed for calculating the loss of implanted ions by resputtering as a function of the implanted ion dose and the sputtering yield. Numerical data are produced therefrom which permit a good order-of-magnitude estimate of the loss for any ion/solid combination in which the ions are heavier than the solid atoms, and for any ion energy from 10 to 300 keV. The implanted ion dose is measured by integration of the ion beam current, and equipment and techniques are described which make possible the accurate integration of an ion current in an electromagnetic isotope separator. The methods are applied to two sample cases, one being a stable isotope, the other a radioisotope. In both cases independent methods are used to show that the implantation is indeed quantitative, as predicted. At the same time the sample cases are used to demonstrate two possible applications for quantitative ion implantation, viz. firstly for the manufacture of calibration standards for instrumental micromethods of elemental trace analysis in metals, and secondly for the determination of the half-lives of long-lived radioisotopes by a specific activity method. It is concluded that the present study has advanced quantitative ion implantation to the state where it can be successfully applied to the solution of problems in other fields

  7. Heating tokamaks via the ion-cyclotron and ion-ion hybrid resonances

    International Nuclear Information System (INIS)

    Perkins, F.W.

    1977-04-01

    For the ion-ion hybrid resonance it is shown that: (1) the energy absorption occurs via a sequence of mode conversions; (2) a poloidal field component normal to the ion-ion hybrid mode conversion surface strongly influences the mode conversion process so that roughly equal electron and ion heating occurs in the present proton-deuterium experiments, while solely electron heating is predicted to prevail in deuterium-tritium reactors; (3) the ion-ion hybrid resonance suppresses toroidal eigenmodes; and (4) wave absorption in minority fundamental ion-cyclotron heating experiments will be dominated by ion-ion hybrid mode conversion absorption for minority concentrations exceeding roughly 1 percent. For the ion-cyclotron resonance, it is shown that: (1) ion-cyclotron mode conversion leads to surface electron heating; and (2) ion-cyclotron mode conversion absorption dominates fundamental ion-cyclotron absorption thereby preventing efficient ion heating

  8. Modeling of retention of some fission products and actinides by ion-exchange chromatography with a complexing agent. Application to the determination of selectivity coefficients

    International Nuclear Information System (INIS)

    Gurdale-Tack, K.; Aubert, M.; Chartier, F.

    2000-01-01

    For an accurate determination of the isotopic and elemental composition of americium (Am), curium (Cm), neodymium (Nd) and cesium (Cs) in spent nuclear fuels, performed by Thermal Ionization Mass Spectrometry (TIMS) and Inductively Coupled Plasma Mass Spectrometry (ICP-MS), it is necessary to separate these elements before analysis. This separation is mandatory because of isobaric interferences between americium and curium, neodymium and samarium (Sm) and between cesium and barium (Ba). This is the reason why Ba and Sm are analyzed with the other four elements. Separation is carried out by cation-exchange chromatography on a silica-based stationary phase in the presence of a complexing eluent. The complexing agent is 2-hydroxy-2-methyl butanoic acid (HMB), a monoprotic acid (HL) with a pK a of 3.6. Cations (M n+ ) interact with it to form ML y (n-y)+ complexes. Optimization of chromatographic separation conditions requires monitoring of the pH and eluent composition. The influence of each parameter on metal ion retention and on selectivity was investigated. The first studies on standard solutions with Sm(III), Nd(III), Cs(I) and Ba(II) showed that four conditions allow efficient separation. However, only one allows good separation with a real solution of spent nuclear fuels. This condition is a chelating agent concentration of 0.1 mol.l -1 and a pH of 4.2. With the other conditions, co-elution is observed for Cs(I) and Am(III). The overall results were used to study the retention mechanisms. The aim of this modeling is a closer knowledge of the form in which (M n+ and/or ML y (n-y)+ ...) each cationic element is extracted into the stationary phase. In fact, while cations can exist in the eluent in various forms depending on the analytical conditions, their forms may be different in the stationary phase. (authors)

  9. Atmospheric ions and pollution

    International Nuclear Information System (INIS)

    Renoux, A.

    1977-01-01

    The various types of atmospheric ions are defined, the main sources of natural atmospheric radioactivity inducing the formation of radioactive ions in the air are then recalled. The basic equations governing the formation of these ions are indicated and the most current experimental methods used for detecting them are described (Zeleny tubes, Erikson tubes). The special properties of these ions are examined, they are particularly emphasized for the smaller ones. The existence of a discret spectrum of mobilities is shown and the presence of big negative radioactive ions is investigated. Indicative information are given on the granulometric distribution of the atmospheric radioactivity in the air, from small positive Ra A ion fixation on aerosols [fr

  10. Materials analysis fast ions

    CERN Document Server

    Denker, A; Rauschenberg, J; Röhrich, J; Strub, E

    2006-01-01

    Materials analysis with ion beams exploits the interaction of ions with the electrons and nuclei in the sample. Among the vast variety of possible analytical techniques available with ion beams we will restrain to ion beam analysis with ion beams in the energy range from one to several MeV per mass unit. It is possible to use either the back-scattered projectiles (RBS – Rutherford Back Scattering) or the recoiled atoms itself (ERDA – Elastic Recoil Detection Analysis) from the elastic scattering processes. These techniques allow the simultaneous and absolute determination of stoichiometry and depth profiles of the detected elements. The interaction of the ions with the electrons in the sample produces holes in the inner electronic shells of the sample atoms, which recombine and emit X-rays characteristic for the element in question. Particle Induced X-ray Emission (PIXE) has shown to be a fast technique for the analysis of elements with an atomic number above 11.

  11. Ion thruster performance model

    International Nuclear Information System (INIS)

    Brophy, J.R.

    1984-01-01

    A model of ion thruster performance is developed for high flux density cusped magnetic field thruster designs. This model is formulated in terms of the average energy required to produce an ion in the discharge chamber plasma and the fraction of these ions that are extracted to form the beam. The direct loss of high energy (primary) electrons from the plasma to the anode is shown to have a major effect on thruster performance. The model provides simple algebraic equations enabling one to calculate the beam ion energy cost, the average discharge chamber plasma ion energy cost, the primary electron density, the primary-to-Maxwellian electron density ratio and the Maxwellian electron temperature. Experiments indicate that the model correctly predicts the variation in plasma ion energy cost for changes in propellant gas (Ar, Kr, and Xe), grid transparency to neutral atoms, beam extraction area, discharge voltage, and discharge chamber wall temperature

  12. Ion emission microscope microanalyzer

    International Nuclear Information System (INIS)

    Cherepin, V.T.; Olckovsky, V.L.

    1977-01-01

    In the ion microanalyzer (microprobe) the object is exposed to the bombardment of a highly focused ion beam, the secondary ions emitted from the object being analyzed by means of a mass filter. In order to be able to control the position of an analysis synchronous to the local analysis of an object an ion-optical converter (electron image with a fluorescent screen) is placed behind the aperture diaphragm in the direction of the secondary ion beam. The converter allows to make visible in front of the mass filter a non-split ion image characterizing the surface of the surface investigated. Then a certain section may be selected for performing chemical and isotope analyses. (DG) [de

  13. Outlook for ion exchange

    International Nuclear Information System (INIS)

    Kunin, R.

    1977-01-01

    This paper presents the history and theory of ion exchange technology and discusses the usefulness of ion exchange resins which found broad applications in chemical operations. It is demonstrated that the theory of ion exchange technology seems to be moving away from the physical chemist back to the polymer chemist where it started originally. This but confronted the polymer chemists with some knotty problems. It is pointed out that one has still to learn how to use ion exchange materials as efficiently as possible in terms of the waste load that is being pumped into the environment. It is interesting to note that, whereas ion exchange is used for abating pollution, it is also a polluter. One must learn how to use ion exchange as an antipollution device, and at the same time minimize its polluting properties

  14. HEAVY ION LINEAR ACCELERATOR

    Science.gov (United States)

    Van Atta, C.M.; Beringer, R.; Smith, L.

    1959-01-01

    A linear accelerator of heavy ions is described. The basic contributions of the invention consist of a method and apparatus for obtaining high energy particles of an element with an increased charge-to-mass ratio. The method comprises the steps of ionizing the atoms of an element, accelerating the resultant ions to an energy substantially equal to one Mev per nucleon, stripping orbital electrons from the accelerated ions by passing the ions through a curtain of elemental vapor disposed transversely of the path of the ions to provide a second charge-to-mass ratio, and finally accelerating the resultant stripped ions to a final energy of at least ten Mev per nucleon.

  15. Electron-ion collisions

    International Nuclear Information System (INIS)

    Crandall, D.H.

    1982-01-01

    This discussion concentrates on basic physics aspects of inelastic processes of excitation, ionization, and recombination that occur during electron-ion collisions. Except for cases of illustration along isoelectronic sequences, only multicharged (at least +2) ions will be specifically discussed with some emphasis of unique physics aspects associated with ionic charge. The material presented will be discussed from a primarily experimental viewpoint with most attention to electron-ion interacting beams experiments

  16. Ion implantation in semiconductors

    International Nuclear Information System (INIS)

    Gusev, V.; Gusevova, M.

    1980-01-01

    The historical development is described of the method of ion implantation, the physical research of the method, its technological solution and practical uses. The method is universally applicable, allows the implantation of arbitrary atoms to an arbitrary material, ensures high purity of the doping element. It is linked with sample processing at low temperatures. In implantation it is possible to independently change the dose and energy of the ions thereby affecting the spatial distribution of the ions. (M.S.)

  17. Ion implantation in semiconductors

    Energy Technology Data Exchange (ETDEWEB)

    Gusev, V; Gusevova, M

    1980-06-01

    The historical development of the method of ion implantation, the physical research of the method, its technological solution and practical uses is described. The method is universally applicable, allows the implantation of arbitrary atoms to an arbitrary material and ensures high purity of the doping element. It is linked with sample processing at low temperatures. In implantation it is possible to independently change the dose and energy of the ions thereby affecting the spatial distribution of the ions.

  18. Ion implantation in metals

    International Nuclear Information System (INIS)

    Vook, F.L.

    1977-02-01

    The application of ion beams to metals is rapidly emerging as a promising area of research and technology. This report briefly describes some of the recent advances in the modification and study of the basic properties of metals by ion implantation techniques. Most of the research discussed illustrates some of the new and exciting applications of ion beams to metals which are under active investigation at Sandia Laboratories, Albuquerque

  19. Heavy-ion targets

    International Nuclear Information System (INIS)

    Adair, H.L.; Kobisk, E.H.

    1985-01-01

    This chapter examines the characteristics of targets required in heavy-ion accelerator physics experiments. The effects of target parameters on heavy-ion experimental results are reviewed. The target fabrication and characterization techniques used to minimize experimental problems during heavy-ion bombardment are described. Topics considered include target thickness and uniformity, target lifetime, target purity, substrate materials, Doppler shift effects, metal preparations, and target preparation methods

  20. Cluster ion beam facilities

    International Nuclear Information System (INIS)

    Popok, V.N.; Prasalovich, S.V.; Odzhaev, V.B.; Campbell, E.E.B.

    2001-01-01

    A brief state-of-the-art review in the field of cluster-surface interactions is presented. Ionised cluster beams could become a powerful and versatile tool for the modification and processing of surfaces as an alternative to ion implantation and ion assisted deposition. The main effects of cluster-surface collisions and possible applications of cluster ion beams are discussed. The outlooks of the Cluster Implantation and Deposition Apparatus (CIDA) being developed in Guteborg University are shown

  1. Neutron ion temperature measurement

    International Nuclear Information System (INIS)

    Strachan, J.D.; Hendel, H.W.; Lovberg, J.; Nieschmidt, E.B.

    1986-11-01

    One important use of fusion product diagnostics is in the determination of the deuterium ion temperature from the magnitude of the 2.5 MeV d(d,n) 3 He neutron emission. The detectors, calibration methods, and limitations of this technique are reviewed here with emphasis on procedures used at PPPL. In most tokamaks, the ion temperature deduced from neutrons is in reasonable agreement with the ion temperature deduced by other techniques

  2. Ion transport in stellarators

    International Nuclear Information System (INIS)

    Ho, D.D.M.; Kulsrud, R.M.

    1985-09-01

    Stellarator ion transport in the low-collisionality regime with a radial electric field is calculated by a systematic expansion of the drift-Boltzmann equation. The shape of the helical well is taken into account in this calculation. It is found that the barely trapped ions with three to four times the thermal energy give the dominant contribution to the diffusion. Expressions for the ion particle and energy fluxes are derived

  3. Ion optics in an ion source system

    Energy Technology Data Exchange (ETDEWEB)

    Abdel-Salam, F W; Moustafa, O A; El-Khabeary, H [Accelerators Dept, Nuclear Research Center, Atomic Energy Authority, Cairo (Egypt)

    1997-12-31

    An analysis of ion beams from an ion source which consisted of a hemispherical anode, a plane earthed cathode, and a focusing electrode has been carried out. The focal properties of such electrode arrangement were studied using axially symmetric fields. Axial and radial electric fields were obtained as functions of the axial distance. It was found that the radial component of the gradient of potential pushes the ions towards the axis, which indicates the convergent action of the system. The effect of voltage variation between the boundary and the focusing electrode on the position of the plasma boundary are given using the experimental data of the ion source characteristics and its geometrical parameters. The advantages of plasma diffusing outside the source through a small aperture were used by applying a potential to the focusing electrode. It was possible to extract a large ion current from the expanded plasma. The system constituted a lens with a focal length of 29.4 mm. 7 figs.

  4. Ion trap device

    Science.gov (United States)

    Ibrahim, Yehia M.; Smith, Richard D.

    2016-01-26

    An ion trap device is disclosed. The device includes a series of electrodes that define an ion flow path. A radio frequency (RF) field is applied to the series of electrodes such that each electrode is phase shifted approximately 180 degrees from an adjacent electrode. A DC voltage is superimposed with the RF field to create a DC gradient to drive ions in the direction of the gradient. A second RF field or DC voltage is applied to selectively trap and release the ions from the device. Further, the device may be gridless and utilized at high pressure.

  5. Doppler ion program description

    International Nuclear Information System (INIS)

    Henline, P.

    1980-12-01

    The Doppler spectrometer is a conventional Czerny-Turner grating spectrometer with a 1024 channel multiple detector. Light is dispersed across the detector, and its output yields a spectrum covering approximately 200 A. The width of the spectral peak is directly proportional to the temperature of the emitting ions, and determination of the impurity ion temperature allows one to infer the plasma ion temperature. The Doppler ion software system developed at General Atomic uses a TRACOR Northern 1710-31 and an LSI-11/2. The exact configuration of Doublet III is different from TRACOR Northern systems at other facilities

  6. Lithium-ion batteries

    CERN Document Server

    Yoshio, Masaki; Kozawa, Akiya

    2010-01-01

    This book is a compilation of up-to-date information relative to Li-Ion technology. It provides the reader with a single source covering all important aspects of Li-Ion battery operations. It fills the gap between the old original Li-Ion technology and present state of the technology that has developed into a high state of practice. The book is designed to provide a single source for an up-to-date description of the technology associated with the Li-Ion battery industry. It will be useful to researchers interested in energy conversion for the direct conversion of chemical energy into electrica

  7. Correlation ion mobility spectroscopy

    Science.gov (United States)

    Pfeifer, Kent B [Los Lunas, NM; Rohde, Steven B [Corrales, NM

    2008-08-26

    Correlation ion mobility spectrometry (CIMS) uses gating modulation and correlation signal processing to improve IMS instrument performance. Closely spaced ion peaks can be resolved by adding discriminating codes to the gate and matched filtering for the received ion current signal, thereby improving sensitivity and resolution of an ion mobility spectrometer. CIMS can be used to improve the signal-to-noise ratio even for transient chemical samples. CIMS is especially advantageous for small geometry IMS drift tubes that can otherwise have poor resolution due to their small size.

  8. Heavy ion storage rings

    International Nuclear Information System (INIS)

    Schuch, R.

    1987-01-01

    A brief overview of synchrotron storage rings for heavy ions, which are presently under construction in different accelerator laboratories is given. Ions ranging from protons up to uranium ions at MeV/nucleon energies will be injected into these rings using multiturn injection from the accelerators available or being built in these laboratories. After injection, it is planned to cool the phase space distribution of the ions by merging them with cold electron beams or laser beams, or by using stochastic cooling. Some atomic physics experiments planned for these rings are presented. 35 refs

  9. Investigation of neptunium (5), plutonium (5) and americium (5) complexing with some anions of inorganic acids by the method of coprecipitation

    International Nuclear Information System (INIS)

    Moskvin, A.I.; Poznyakov, A.N.; AN SSSR, Moscow. Inst. Geokhimii i Analiticheskoj Khimii)

    1979-01-01

    By using the method of coprecipitation with ferric hydroxide a study has been made of Np(5), Pu(5) and Am(5) ions complexing with the anions of inorganic acids SO 4 2- , SO 3 2- , HCO 3 - and HPO 4 2- . Consideration has been also given to how the process of coprecipitation is affected by such factors as collector mass, microcomponent concentration and solution pH. A composition and stability constants of actinide complexes appearing in the systems under study have been found

  10. High current ion sources

    International Nuclear Information System (INIS)

    Brown, I.G.

    1989-06-01

    The concept of high current ion source is both relative and evolutionary. Within the domain of one particular kind of ion source technology a current of microamperers might be 'high', while in another area a current of 10 Amperes could 'low'. Even within the domain of a single ion source type, what is considered high current performance today is routinely eclipsed by better performance and higher current output within a short period of time. Within their fields of application, there is a large number of kinds of ion sources that can justifiably be called high current. Thus, as a very limited example only, PIGs, Freemen sources, ECR sources, duoplasmatrons, field emission sources, and a great many more all have their high current variants. High current ion beams of gaseous and metallic species can be generated in a number of different ways. Ion sources of the kind developed at various laboratories around the world for the production of intense neutral beams for controlled fusion experiments are used to form large area proton deuteron beams of may tens of Amperes, and this technology can be used for other applications also. There has been significant progress in recent years in the use of microwave ion sources for high current ion beam generation, and this method is likely to find wide application in various different field application. Finally, high current beams of metal ions can be produced using metal vapor vacuum arc ion source technology. After a brief consideration of high current ion source design concepts, these three particular methods are reviewed in this paper

  11. Ion mobilities and ion-atom interaction potentials

    International Nuclear Information System (INIS)

    Gatland, I.R.

    1982-01-01

    The techniques for measuring the mobilities of ions in gases, relating interaction potentials to mobilities, and determining potentials from experimental mobilities are reviewed. Applications are presented for positive alkali ions and negative halogen ions in inert gases. (Auth.)

  12. Ion-beam technologies

    Energy Technology Data Exchange (ETDEWEB)

    Fenske, G.R. [Argonne National Lab., IL (United States)

    1993-01-01

    This compilation of figures and diagrams reviews processes for depositing diamond/diamond-like carbon films. Processes addressed are chemical vapor deposition (HFCVD, PACVD, etc.), plasma vapor deposition (plasma sputtering, ion beam sputtering, evaporation, etc.), low-energy ion implantation, and hybrid processes (biased sputtering, IBAD, biased HFCVD, etc.). The tribological performance of coatings produced by different means is discussed.

  13. Ion beam studies

    International Nuclear Information System (INIS)

    Freeman, J.H.; Chivers, D.J.; Gard, G.A.; Temple, W.

    1977-04-01

    A description of techniques for the production of intense beams of heavy ions is given. A table of recommended operational procedures for most elements is included. The ionisation of boron is considered in some detail because of its particular importance as a dopant for ion implantation. (author)

  14. Where do ions solvate?

    Indian Academy of Sciences (India)

    We study a simple model of ionic solvation inside a water cluster. The cluster is modeled as a spherical dielectric continuum. It is found that unpolarizable ions always prefer the bulk solvation. On the other hand, for polarizable ions, there exists a critical value of polarization above which surface solvation becomes ...

  15. Ion implantation of metals

    International Nuclear Information System (INIS)

    Dearnaley, G.

    1976-01-01

    In this part of the paper descriptions are given of the effects of ion implantation on (a) friction and wear in metals; and (b) corrosion of metals. In the study of corrosion, ion implantation can be used either to introduce a constituent that is known to convey corrosion resistance, or more generally to examine the parameters which control corrosion. (U.K.)

  16. Heavy ion fusion

    International Nuclear Information System (INIS)

    Bangerter, R.O.

    1986-01-01

    This report on the International Symposium on Heavy Ion Fusion held May 27-29, 1986 summarizes the problems and achievements in the areas of targets, accelerators, focussing, reactor studies, and system studies. The symposium participants recognize that there are large uncertainties in Heavy Ion Fusion but many of them are also optimistic that HIF may ultimately be the best approach to fusion

  17. High brightness ion source

    International Nuclear Information System (INIS)

    Dreyfus, R.W.; Hodgson, R.T.

    1975-01-01

    A high brightness ion beam is obtainable by using lasers to excite atoms or molecules from the ground state to an ionized state in increments, rather than in one step. The spectroscopic resonances of the atom or molecule are used so that relatively long wavelength, low power lasers can be used to obtain such ion beam

  18. Heavy ion inertial fusion

    International Nuclear Information System (INIS)

    Fessenden, T.J.; Friedman, A.

    1991-01-01

    This report describes the research status in the following areas of research in the field of heavy ion inertial fusion: (1) RF accelerators, storage rings, and synchrotrons; (2) induction linacs; (3) recirculation induction accelerator approach; (4) a new accelerator concept, the ''Mirrortron''; (5) general issues of transport, including beam merging, production of short, fat quadrupoles with nearly linear focusing, calculations of beam behaviour in image fields; 3-D electrostatic codes on drift compression with misalignments and transport around bends; (6) injectors, ion sources and RFQs, a.o., on the development of a 27 MHz RFQ to be used for the low energy portion of a new injector for all ions up to Uranium, and the development of a 2 MV carbon ion injector to provide 16 C + beams of 0.5 A each for ILSE; (7) beam transport from accelerator to target, reporting, a.o., the feasibility to suppress third-order aberrations; while Particle-in-Cell simulations on the propagation of a non-neutral ion beam in a low density gas identified photo-ionization by thermal X-rays from the target as an important source of defocusing; (9) heavy ion target studies; (10) reviewing experience with laser drivers; (11) ion cluster stopping and muon catalyzed fusion; (12) heavy ion systems, including the option of a fusion-fission burner. 1 tab

  19. Ion mobility sensor system

    Science.gov (United States)

    Xu, Jun; Watson, David B.; Whitten, William B.

    2013-01-22

    An ion mobility sensor system including an ion mobility spectrometer and a differential mobility spectrometer coupled to the ion mobility spectrometer. The ion mobility spectrometer has a first chamber having first end and a second end extending along a first direction, and a first electrode system that generates a constant electric field parallel to the first direction. The differential mobility spectrometer includes a second chamber having a third end and a fourth end configured such that a fluid may flow in a second direction from the third end to the fourth end, and a second electrode system that generates an asymmetric electric field within an interior of the second chamber. Additionally, the ion mobility spectrometer and the differential mobility spectrometer form an interface region. Also, the first end and the third end are positioned facing one another so that the constant electric field enters the third end and overlaps the fluid flowing in the second direction.

  20. Cryogenic surface ion traps

    International Nuclear Information System (INIS)

    Niedermayr, M.

    2015-01-01

    Microfabricated surface traps are a promising architecture to realize a scalable quantum computer based on trapped ions. In principle, hundreds or thousands of surface traps can be located on a single substrate in order to provide large arrays of interacting ions. To this end, trap designs and fabrication methods are required that provide scalable, stable and reproducible ion traps. This work presents a novel surface-trap design developed for cryogenic applications. Intrinsic silicon is used as the substrate material of the traps. The well-developed microfabrication and structuring methods of silicon are utilized to create simple and reproducible traps. The traps were tested and characterized in a cryogenic setup. Ions could be trapped and their life time and motional heating were investigated. Long ion lifetimes of several hours were observed and the measured heating rates were reproducibly low at around 1 phonon per second at a trap frequency of 1 MHz. (author) [de

  1. Molecular ion photofragment spectroscopy

    International Nuclear Information System (INIS)

    Bustamente, S.W.

    1983-11-01

    A new molecular ion photofragment spectrometer is described which features a supersonic molecular beam ion source and a radio frequency octapole ion trap interaction region. This unique combination allows several techniques to be applied to the problem of detecting a photon absorption event of a molecular ion. In particular, it may be possible to obtain low resolution survey spectra of exotic molecular ions by using a direct vibrational predissociation process, or by using other more indirect detection methods. The use of the spectrometer is demonstrated by measuring the lifetime of the O 2 + ( 4 π/sub u/) metastable state which is found to consist of two main components: the 4 π/sub 5/2/ and 4 π/sub -1/2/ spin components having a long lifetime (approx. 129 ms) and the 4 π/sub 3/2/ and 4 π/sub 1/2/ spin components having a short lifetime (approx. 6 ms)

  2. Ion Implantation of Polymers

    DEFF Research Database (Denmark)

    Popok, Vladimir

    2012-01-01

    The current paper presents a state-of-the-art review in the field of ion implantation of polymers. Numerous published studies of polymers modified by ion beams are analysed. General aspects of ion stopping, latent track formation and changes of structure and composition of organic materials...... are discussed. Related to that, the effects of radiothermolysis, degassing and carbonisation are considered. Specificity of depth distributions of implanted into polymers impurities is analysed and the case of high-fluence implantation is emphasised. Within rather broad topic of ion bombardment, the focus...... is put on the low-energy implantation of metal ions causing the nucleation and growth of nanoparticles in the shallow polymer layers. Electrical, optical and magnetic properties of metal/polymer composites are under the discussion and the approaches towards practical applications are overviewed....

  3. A novel ion imager for secondary ion mass spectrometry

    International Nuclear Information System (INIS)

    Matsumoto, Kazuya; Miyata, Kenji; Nakamura, Tsutomu

    1993-01-01

    This paper describes a new area detector for secondary ion mass spectrometry (SIMS) ion microscope, and its performance. The operational principle is based on detecting the change in potential of a floating photodiode caused by the ion-induced secondary-electron emission and the incoming ion itself. The experiments demonstrated that 10 1 -10 5 aluminum ions per pixel can be detected with good linear response. Moreover, relative ion sensitivities from hydrogen to lead were constant within a factor of 2. The performance of this area detector provides the potential for detection of kiloelectronvolt ion images with current ion microscopy

  4. Ion thermometers - nuclear reactor applications

    International Nuclear Information System (INIS)

    Rosenkranz, J.; Jakes, D.

    The principle is briefly described of ion thermometers and the effects are reported of radiation on the ion crystal properties. The results show that ion thermometers are applicable for in-core measurements. (J.P.)

  5. Plasma source ion implantation

    International Nuclear Information System (INIS)

    Conrad, J.R.; Forest, C.

    1986-01-01

    The authors' technique allows the ion implantation to be performed directly within the ion source at higher currents without ion beam extraction and transport. The potential benefits include greatly increased production rates (factors of 10-1000) and the ability to implant non-planar targets without rastering or shadowing. The technique eliminates the ion extractor grid set, beam raster equipment, drift space and target manipulator equipment. The target to be implanted is placed directly within the plasma source and is biased to a large negative potential so that plasma ions gain energy as they accelerate through the potential drop across the sheath that forms at the plasma boundary. Because the sheath surrounds the target on all sides, all surfaces of the target are implanted without the necessity to raster the beam or to rotate the target. The authors have succeeded in implanting nitrogen ions in a silicon target to the depths and concentrations required for surface treatment of materials like stainless steel and titanium alloys. They have performed ESCA measurements of the penetration depth profile of a silicon target that was biased to 30 kV in a nitrogen discharge plasma. Nitrogen ions were implanted to a depth of 700A at a peak concentration of 30% atomic. The measured profile is quite similar to a previously obtained profile in titanium targets with conventional techniques

  6. Laser-cooled atomic ions as probes of molecular ions

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Kenneth R.; Viteri, C. Ricardo; Clark, Craig R.; Goeders, James E.; Khanyile, Ncamiso B.; Vittorini, Grahame D. [Schools of Chemistry and Biochemistry, Computational Science and Engineering and Physics, Georgia Institute of Technology, Atlanta, GA 30332 (United States)

    2015-01-22

    Trapped laser-cooled atomic ions are a new tool for understanding cold molecular ions. The atomic ions not only sympathetically cool the molecular ions to millikelvin temperatures, but the bright atomic ion fluorescence can also serve as a detector of both molecular reactions and molecular spectra. We are working towards the detection of single molecular ion spectra by sympathetic heating spectroscopy. Sympathetic heating spectroscopy uses the coupled motion of two trapped ions to measure the spectra of one ion by observing changes in the fluorescence of the other ion. Sympathetic heating spectroscopy is a generalization of quantum logic spectroscopy, but does not require ions in the motional ground state or coherent control of the ion internal states. We have recently demonstrated this technique using two isotopes of Ca{sup +} [Phys. Rev. A, 81, 043428 (2010)]. Limits of the method and potential applications for molecular spectroscopy are discussed.

  7. Ion-Ion Plasmas Produced by Electron Beams

    Science.gov (United States)

    Fernsler, R. F.; Leonhardt, D.; Walton, S. G.; Meger, R. A.

    2001-10-01

    The ability of plasmas to etch deep, small-scale features in materials is limited by localized charging of the features. The features charge because of the difference in electron and ion anisotropy, and thus one solution now being explored is to use ion-ion plasmas in place of electron-ion plasmas. Ion-ion plasmas are effectively electron-free and consist mainly of positive and negative ions. Since the two ion species behave similarly, localized charging is largely eliminated. However, the only way to produce ion-ion plasmas at low gas pressure is to convert electrons into negative ions through two-body attachment to neutrals. While the electron attachment rate is large at low electron temperatures (Te < 1 eV) in many of the halogen gases used for processing, these temperatures occur in most reactors only during the afterglow when the heating fields are turned off and the plasma is decaying. By contrast, Te is low nearly all the time in plasmas produced by electron beams, and therefore electron beams can potentially produce ion-ion plasmas continuously. The theory of ion-ion plasmas formed by pulsed electron beams is examined in this talk and compared with experimental results presented elsewhere [1]. Some general limitations of ion-ion plasmas, including relatively low flux levels, are discussed as well. [1] See the presentation by D. Leonhardt et al. at this conference.

  8. Heavy-ion dosimetry

    International Nuclear Information System (INIS)

    Schimmerling, W.

    1980-03-01

    This lecture deals with some of the more important physical characteristics of relativistic heavy ions and their measurement, with beam delivery and beam monitoring, and with conventional radiation dosimetry as used in the operation of the BEVALAC biomedical facility for high energy heavy ions (Lyman and Howard, 1977; BEVALAC, 1977). Even so, many fundamental aspects of the interaction of relativistic heavy ions with matter, including important atomic physics and radiation chemical considerations, are not discussed beyond the reminder that such additional understanding is required before an adequte perspective of the problem can be attained

  9. Ion implantation technology

    CERN Document Server

    Downey, DF; Jones, KS; Ryding, G

    1993-01-01

    Ion implantation technology has made a major contribution to the dramatic advances in integrated circuit technology since the early 1970's. The ever-present need for accurate models in ion implanted species will become absolutely vital in the future due to shrinking feature sizes. Successful wide application of ion implantation, as well as exploitation of newly identified opportunities, will require the development of comprehensive implant models. The 141 papers (including 24 invited papers) in this volume address the most recent developments in this field. New structures and possible approach

  10. IN MEMORIAM ION VATAMANU

    Directory of Open Access Journals (Sweden)

    S.P. Palii

    2012-12-01

    Full Text Available A dreamer in his creative solitude, an objective and lucid analyst of history and contemporaneity, an energetic and decisive leader with an uncanny ability for crisis management – all these describe Ion Vatamanu. His wife Elena and daughters Mihaela, Mariana, Leontina treasure a personal universe in which the magical spark of Ion Vatamanu’s love and joy of life meld the everyday in and out of poetry. Ion Vatamanu’s instantaneous connection to the audiences and deeply felt words still touch the hearts of his many colleagues and friends. Downloads: 2

  11. Ion implantation for microelectronics

    International Nuclear Information System (INIS)

    Dearnaley, G.

    1977-01-01

    Ion implantation has proved to be a versatile and efficient means of producing microelectronic devices. This review summarizes the relevant physics and technology and assesses the advantages of the method. Examples are then given of widely different device structures which have been made by ion implantation. While most of the industrial application has been in silicon, good progress continues to be made in the more difficult field of compound semiconductors. Equipment designed for the industrial ion implantation of microelectronic devices is discussed briefly. (Auth.)

  12. Multivalent ion conducting solids

    Energy Technology Data Exchange (ETDEWEB)

    Imanaka, N. [Osaka Univ., Suita, Osaka (Japan). Dept. of Applied Chemistry

    2008-07-01

    Solid electrolytes possess important characteristics for industrial applications. Only a single ionic species can macroscopically migrate in these solids. This paper described a the new NASICON (M-Zr-Nb-P-O) type system, exhibiting an exceptionally high level of trivalent M3+ ion conductivity on polycrystalline solids. The partial substitution of the smaller higher valent Nb5+ ion for Zr4+ stabilized the NASICON phase and realized the M3+ ion conduction in the NASICON structure. It was concluded that the conductivities of the series are comparable to those of the practically applied solid electrolytes of oxide anion conductors of YSZ and CSZ. 3 refs., 2 figs.

  13. Heavy ion physics

    International Nuclear Information System (INIS)

    Kalpakchieva, R.; Cherepanov, E.A.

    1993-01-01

    The international school-seminar on heavy ion physics had been organized in Dubna in may of 1993. The scientific program of reports covers the following main topics: synthesis and properties of heavy nuclei; synthesis and investigation of properties of exotic nuclei; experiments with radioactive nuclear beams; interaction between complex nuclei at low and intermediate energies. It also includes reports on laser spectroscopy and exotic nuclear beams, on some application of heavy ion beams for the problems of solid state physics, on construction of multidetector facilities and on developing of heavy ion accelerator complexes. Short communication

  14. Compact microwave ion source

    International Nuclear Information System (INIS)

    Leung, K.N.; Walther, S.; Owren, H.W.

    1985-05-01

    A small microwave ion source has been fabricated from a quartz tube with one end enclosed by a two grid accelerator. The source is also enclosed by a cavity operated at a frequency of 2.45 GHz. Microwave power as high as 500 W can be coupled to the source plasma. The source has been operated with and without multicusp fields for different gases. In the case of hydrogen, ion current density of 200 mA/cm -2 with atomic ion species concentration as high as 80% has been extracted from the source

  15. Jet laser ion source

    International Nuclear Information System (INIS)

    Dem'yanov, A.V.; Sidorov, S.V.

    1994-01-01

    External laser injector of multicharged ions (MCI) is developed in which wide-aperture aberration-free wire gauze spherical shape electrodes are applied for effective MCI extraction from laser plasma and beam focusing. Axial plasma compression by solenoid magnetic field is used to reduce ion losses due to transverse movement of the scattering laser plasma. Transverse magnetic field created by another solenoid facilitates the effective laser plasma braking and consequently, leads to the narrowing of energy spectrum of plasma ions and its shift towards lower energies. 2 refs.; 3 figs

  16. Carbon Ion Therapy

    DEFF Research Database (Denmark)

    Bassler, Niels; Hansen, David Christoffer; Herrmann, Rochus

    On the importance of choice of target size for selective boosting of hypoxic tumor subvolumina in carbon ion therapy Purpose: Functional imaging methods in radiotherapy are maturing and can to some extent uncover radio resistant structures found within a tumour entity. Selective boost of identified...... effect. All cell lines investigated here did not reach an OER of 1, even for the smaller structures, which may indicate that the achievable dose average LET of carbon ions is too low, and heavier ions than carbon may be considered for functional LET-painting....

  17. Atomic negative ions

    International Nuclear Information System (INIS)

    Brage, T.

    1991-01-01

    We review some of the recent progress in the studies of alkaline-earth, negative ions. Computations of autodetachment rates, electron affinities and transition wavelengths are discussed and some new and improved results are given

  18. Ion exchange phenomena

    Energy Technology Data Exchange (ETDEWEB)

    Bourg, I.C.; Sposito, G.

    2011-05-01

    Ion exchange phenomena involve the population of readily exchangeable ions, the subset of adsorbed solutes that balance the intrinsic surface charge and can be readily replaced by major background electrolyte ions (Sposito, 2008). These phenomena have occupied a central place in soil chemistry research since Way (1850) first showed that potassium uptake by soils resulted in the release of an equal quantity of moles of charge of calcium and magnesium. Ion exchange phenomena are now routinely modeled in studies of soil formation (White et al., 2005), soil reclamation (Kopittke et al., 2006), soil fertilitization (Agbenin and Yakubu, 2006), colloidal dispersion/flocculation (Charlet and Tournassat, 2005), the mechanics of argillaceous media (Gajo and Loret, 2007), aquitard pore water chemistry (Tournassat et al., 2008), and groundwater (Timms and Hendry, 2007; McNab et al., 2009) and contaminant hydrology (Chatterjee et al., 2008; van Oploo et al., 2008; Serrano et al., 2009).

  19. Ion implantation control system

    International Nuclear Information System (INIS)

    Gault, R. B.; Keutzer, L. L.

    1985-01-01

    A control system is disclosed for an ion implantation system of the type in which the wafers to be implanted are mounted around the periphery of a disk which rotates and also moves in a radial direction relative to an ion beam to expose successive sections of each wafer to the radiation. The control system senses beam current which passes through one or more apertures in the disk and is collected by a Faraday cup. This current is integrated to obtain a measure of charge which is compared with a calculated value based upon the desired ion dosage and other parameters. The resultant controls the number of incremental steps the rotating disk moves radially to expose the adjacent sections of each wafer. This process is continued usually with two or more traverses until the entire surface of each wafer has been implanted with the proper ion dosage

  20. Sensing with Ion Channels

    CERN Document Server

    Martinac, Boris

    2008-01-01

    All living cells are able to detect and translate environmental stimuli into biologically meaningful signals. Sensations of touch, hearing, sight, taste, smell or pain are essential to the survival of all living organisms. The importance of sensory input for the existence of life thus justifies the effort made to understand its molecular origins. Sensing with Ion Channels focuses on ion channels as key molecules enabling biological systems to sense and process the physical and chemical stimuli that act upon cells in their living environment. Its aim is to serve as a reference to ion channel specialists and as a source of new information to non specialists who want to learn about the structural and functional diversity of ion channels and their role in sensory physiology.

  1. Ion implantation apparatus

    International Nuclear Information System (INIS)

    Forneris, J.L.; Hicks, W.W.; Keller, J.H.; McKenna, C.M.; Siermarco, J.A.; Mueller, W.F.

    1981-01-01

    The invention relates to ion bombardment or implantation apparatus. It comprises an apparatus for bombarding a target with a beam of ions, including an arrangement for measuring the ion beam current and controlling the surface potential of the target. This comprises a Faraday cage formed, at least in part, by the target and by walls adjacent to, and electrically insulated from, the target and surrounding the beam. There is at least one electron source for supplying electrons to the interior of the Faraday cage and means within the cage for blocking direct rectilinear radiation from the source to the target. The target current is measured and combined with the wall currents to provide a measurement of the ion beam current. The quantity of electrons supplied to the interior of the cage can be varied to control the target current and thereby the target surface potential. (U.K.)

  2. Electrostatic ion acoustic waves

    International Nuclear Information System (INIS)

    Hasegawa, A.

    1983-01-01

    In this paper, certain aspects of plasma physics are illustrated through a study of electrostatic ion acoustic waves. The paper consists of three Sections. Section II deals with linear properties of the ion acoustic wave including derivation of the dispersions relation with the effect of Landau damping and of an ambient magnetic field. The section also introduces the excitation processes of the ion acoustic wave due to an electron drift or to a stimulated Brillouin scattering. The nonlinear properties are introduced in Section III and IV. In Section III, incoherent nonlinear effects such as quasilinear and mode-coupling saturations of the instability are discussed. The coherent nonlinear effects such as the generation of ion acoustic solitons, shocks and weak double layers are presented in Section IV. (Auth.)

  3. Trapping radioactive ions

    CERN Document Server

    Kluge, Heinz-Jürgen

    2004-01-01

    Trapping devices for atomic and nuclear physics experiments with radioactive ions are becoming more and more important at accelerator facilities. While about ten years ago only one online Penning trap experiment existed, namely ISOLTRAP at ISOLDE/CERN, meanwhile almost every radioactive beam facility has installed or plans an ion trap setup. This article gives an overview on ion traps in the operation, construction or planing phase which will be used for fundamental studies with short-lived radioactive nuclides such as mass spectrometry, laser spectroscopy and nuclear decay spectroscopy. In addition, this article summarizes the use of gas cells and radiofrequency quadrupole (Paul) traps at different facilities as a versatile tool for ion beam manipulation like retardation, cooling, bunching, and cleaning.

  4. Ion plasma electron gun

    International Nuclear Information System (INIS)

    Wakalopulos, G.

    1976-01-01

    In the disclosed electron gun positive ions generated by a hollow cathode plasma discharge in a first chamber are accelerated through control and shield grids into a second chamber containing a high voltage cold cathode. These positive ions bombard a surface of the cathode causing the cathode to emit secondary electrons which form an electron beam having a distribution adjacent to the cathode emissive surface substantially the same as the distribution of the ion beam impinging upon the cathode. After passing through the grids and the plasma discharge chamber, the electron beam exits from the electron gun via a foil window. Control of the generated electron beam is achieved by applying a relatively low control voltage between the control grid and the electron gun housing (which resides at ground potential) to control the density of the positive ions bombarding the cathode

  5. Ion sensing method

    Science.gov (United States)

    Smith, Richard Harding; Martin, Glenn Brian

    2004-05-18

    The present invention allows the determination of trace levels of ionic substances in a sample solution (ions, metal ions, and other electrically charged molecules) by coupling a separation method, such as liquid chromatography, with ion selective electrodes (ISE) prepared so as to allow detection at activities below 10.sup.-6 M. The separation method distributes constituent molecules into fractions due to unique chemical and physical properties, such as charge, hydrophobicity, specific binding interactions, or movement in an electrical field. The separated fractions are detected by means of the ISE(s). These ISEs can be used singly or in an array. Accordingly, modifications in the ISEs are used to permit detection of low activities, specifically, below 10.sup.-6 M, by using low activities of the primary analyte (the molecular species which is specifically detected) in the inner filling solution of the ISE. Arrays constructed in various ways allow flow-through sensing for multiple ions.

  6. EPR of uranium ions

    International Nuclear Information System (INIS)

    Ursu, I.; Lupei, V.

    1984-02-01

    A review of the electron paramagnetic resonance data on the uranium ions is given. After a general account of the electronic structure of the uranium free atoms and ions, the influence of the external fields (magnetic field, crystal fields) is discussed. The main information obtained from EPR studies on the uranium ions in crystals are emphasized: identification of the valence and of the ground electronic state, determination of the structure of the centers, crystal field effects, role of the intermediate coupling and of the J-mixing, role of the covalency, determination of the nuclear spin, maqnetic dipole moment and electric quadrupole moment of the odd isotopes of uranium. These data emphasize the fact that the actinide group has its own identity and this is accutely manifested at the beginning of the 5fsup(n) series encompassed by the uranium ions. (authors)

  7. Trapping radioactive ions

    International Nuclear Information System (INIS)

    Kluge, H.-J.; Blaum, K.

    2004-01-01

    Trapping devices for atomic and nuclear physics experiments with radioactive ions are becoming more and more important at accelerator facilities. While about ten years ago only one online Penning trap experiment existed, namely ISOLTRAP at ISOLDE/CERN, meanwhile almost every radioactive beam facility has installed or plans an ion trap setup. This article gives an overview on ion traps in the operation, construction or planing phase which will be used for fundamental studies with short-lived radioactive nuclides such as mass spectrometry, laser spectroscopy and nuclear decay spectroscopy. In addition, this article summarizes the use of gas cells and radiofrequency quadrupole (Paul) traps at different facilities as a versatile tool for ion beam manipulation like retardation, cooling, bunching, and cleaning

  8. Ion exchange equilibrium constants

    CERN Document Server

    Marcus, Y

    2013-01-01

    Ion Exchange Equilibrium Constants focuses on the test-compilation of equilibrium constants for ion exchange reactions. The book first underscores the scope of the compilation, equilibrium constants, symbols used, and arrangement of the table. The manuscript then presents the table of equilibrium constants, including polystyrene sulfonate cation exchanger, polyacrylate cation exchanger, polymethacrylate cation exchanger, polysterene phosphate cation exchanger, and zirconium phosphate cation exchanger. The text highlights zirconium oxide anion exchanger, zeolite type 13Y cation exchanger, and

  9. Heavy ion accelerators

    International Nuclear Information System (INIS)

    Schmelzer, C.

    1974-01-01

    This review of the present state of work on heavy-ion accelerators pays particular attention to the requirements for nuclear research. It is divided into the following sections: single-particle versus collective acceleration, heavy-ion accelerators, beam quality, and a status report on the UNILAC facility. Among the topics considered are the recycling cyclotron, linacs with superconducting resonators, and acceleration to the GeV/nucleon range. (8 figures, 2 tables) (U.S.)

  10. Ion Mass Determination

    DEFF Research Database (Denmark)

    2010-01-01

    An apparatus (100) is described for determining the mass of ions, the apparatus configured to hold a plasma (101 ) having a plasma potential. The apparatus (100) comprises an electrode (102) having a surface extending in a surface plane and an insulator (104) interfacing with the electrode (102......, and a processing unit (108) configured to interpret the detected impact locations in terms of the mass of the impacting ions....

  11. Ion beam diagnosis

    International Nuclear Information System (INIS)

    Strehl, P.

    1994-04-01

    This report is an introduction to ion beam diagnosis. After a short description of the most important ion beam parameters measurements of the beam current by means of Faraday cups, calorimetry, and beam current transformers and measurements of the beam profile by means of viewing screens, profile grids and scanning devices, and residual gas ionization monitors are described. Finally measurements in the transverse and longitudinal phase space are considered. (HSI)

  12. Ion implantation - an introduction

    International Nuclear Information System (INIS)

    Townsend, P.D.

    1986-01-01

    Ion implantation is a widely used technique with a literature that covers semiconductor production, surface treatments of steels, corrosion resistance, catalysis and integrated optics. This brief introduction outlines advantages of the technique, some aspects of the underlying physics and examples of current applications. Ion implantation is already an essential part of semiconductor technology while in many other areas it is still in an early stage of development. The future scope of the subject is discussed. (author)

  13. 2010 ion run: completed!

    CERN Multimedia

    CERN Bulletin

    2010-01-01

    After a very fast switchover from protons to lead ions, the LHC has achieved performances that allowed the machine to exceed both peak and integrated luminosity by a factor of three. Thanks to this, experiments have been able to produce high-profile results on ion physics almost immediately, confirming that the LHC was able to keep its promises for ions as well as for protons.   First direct observation of jet quenching. A seminar on 2 December was the opportunity for the ALICE, ATLAS and CMS collaborations to present their first results on ion physics in front of a packed auditorium. These results are important and are already having a major impact on the understanding of the physics processes that involve the basic constituents of matter at high energies. In the ion-ion collisions, the temperature is so high that partons (quarks and gluons), which are usually constrained inside the nucleons, are deconfined to form a highly dense and hot soup known as quark-gluon plasma (QGP). The existence of ...

  14. Collective focusing ion accelerator

    International Nuclear Information System (INIS)

    Goldin, F.J.

    1986-01-01

    The principal subject of this dissertation is the trapping confinement of pure electron plasmas in bumpy toroidal magnetic fields, with particular attention given to the trapping procedure and the behavior of the plasma during the final equilibrium. The most important aspects of the equilibrium studied were the qualitative nature of the plasma configuration and motion and its density, distribution and stability. The motivation for this study was that an unneutralized cloud of electrons contained in a toroidal system, sufficiently dense and stable, may serve to electrostatically focus ions (against centrifugal and self space charge forces) in a cyclic ion accelerator. Such an accelerator, known as a Collective Focusing Ion Accelerator (CFIA) could be far smaller than conventional designs (which use external magnetic fields directly to focus the ions) due to the smaller gyro-radium of an electron in a magnetic field of given strength. The electron cloud generally drifted poloidally at a finite radius from the toroidal minor axis. As this would preclude focusing ions with such clouds, damping this motion was investigated. Finite resistance in the normally perfectly conductive vessel wall did this. In further preparation for a working CFIA, additional experiments studied the effect of ions on the stability of the electron cloud

  15. Ion mixing and numerical simulation of different ions produced in the ECR ion source

    International Nuclear Information System (INIS)

    Shirkov, G.D.

    1996-01-01

    This paper is to continue theoretical investigations and numerical simulations in the physics of ECR ion sources within the CERN program on heavy ion acceleration. The gas (ion) mixing effect in ECR sources is considered here. It is shown that the addition of light ions to the ECR plasma has three different mechanisms to improve highly charged ion production: the increase of confinement time and charge state of highly ions as the result of ion cooling; the concentration of highly charged ions in the central region of the source with high energy and density of electrons; the increase of electron production rate and density of plasma. The numerical simulations of lead ion production in the mixture with different light ions and different heavy and intermediate ions in the mixture with oxygen, are carried out to predict the principal ECR source possibilities for LHC applications. 18 refs., 23 refs

  16. Biomaterials modification by ion beam

    International Nuclear Information System (INIS)

    Zhang Tonghe; Yi Zhongzhen; Zhang Xu; Wu Yuguang

    2001-01-01

    Ion beam technology is one of best ways for the modification of biomaterials. The results of ion beam modification of biomaterials are given. The method and results of improved biocompatibility are indicated by ion beam technology. The future development of ion beam modification of biomaterials is discussed

  17. Solvent phase characterisation of lanthanide(3) and americium(3) complexes with malonamide (tema) and ter-pyridine ligands by EXAFS: comparison with single crystals

    International Nuclear Information System (INIS)

    Den Auwer, C.; Presson, M.T.; Grigoriev, M.; Madic, C.; Nierlich, M.; Thuery, P.; David, F.; Hubert, S.; Drew, M.G.B.; Hudson, M.J.; Iveson, P.B.; Russell, M.L.

    2002-01-01

    In order to develop molecules that will be good candidates for the extractive separation of the various elements contained within nuclear fuels, 4f and 5f molecular chemistry has been the subject of numerous studies. Thus, to better understand the ligand to cation interaction and to fine tune the theoretical models, precise knowledge about the cation co-ordination sphere must be obtained. More precisely, both structural and electronic data must be acquired in order to define the role of the cation frontier orbitals within the complex. To do so, various structural probes must be used, from vibrational and nuclear techniques to X-ray spectroscopies. In the field of actinide solvent extraction, the species of interest are in the solvent phase and both solid state diffraction methods and solvent phase X-ray absorption spectroscopy have become of primary importance lately. A number of Ln(III) and Am(III) complexes of the type M(NO 3 ) 3 L 1,2 (where M is either Ln 3+ or Am 3+ and L is either the 2,2',6',2 - ter-pyridine (Tpy) or the N,N,N',N' tetraethyl-malonamide (TEMA) ligand) have been crystallographically characterised in the solid state. In order to obtain structural information in the solvent phase, EXAFS L III edge measurements have been performed on the cation (DCI ring at the LURE facility). The overall contraction (-0.05 Angstrom) of the cation co-ordination sphere from Nd 3+ to Lu 3+ reflects the decrease in the lanthanide ionic radii. With the TEMA ligand, this steric constraint generates the elongation of one nitrate bond, leading to one formally monodendate nitrate for the late Ln ions. Comparison is made with the Tpy ligand. In the case of Am 3+ cation, comparison with isostructural Nd 3+ shows that similar co-ordination spheres are obtained, either with the TEMA or the Tpy ligands. (authors)

  18. Ion-selective electrode reviews

    CERN Document Server

    Thomas, J D R

    1983-01-01

    Ion-Selective Electrode Reviews, Volume 5 is a collection of articles that covers ion-speciation. The book aims to present the advancements of the range and capabilities of selective ion-sensors. The topics covered in the selection are neutral carrier based ion-selective electrodes; reference electrodes and liquid junction effects in ion-selective electrode potentiometry; ion transfer across water/organic phase boundaries and analytical; and carbon substrate ion-selective electrodes. The text will be of great use to chemists and chemical engineers.

  19. Ion optics of RHIC EBIS

    Energy Technology Data Exchange (ETDEWEB)

    Pikin, A.; Alessi, J.; Beebe, E.; Kponou, A.; Okamura, M.; Raparia, D.; Ritter, J.; Tan, Y.; Kuznetsov, G.

    2011-09-10

    RHIC EBIS has been commissioned to operate as a versatile ion source on RHIC injection facility supplying ion species from He to Au for Booster. Except for light gaseous elements RHIC EBIS employs ion injection from several external primary ion sources. With electrostatic optics fast switching from one ion species to another can be done on a pulse to pulse mode. The design of an ion optical structure and the results of simulations for different ion species are presented. In the choice of optical elements special attention was paid to spherical aberrations for high-current space charge dominated ion beams. The combination of a gridded lens and a magnet lens in LEBT provides flexibility of optical control for a wide range of ion species to satisfy acceptance parameters of RFQ. The results of ion transmission measurements are presented.

  20. Ion beam inertial fusion

    International Nuclear Information System (INIS)

    Bangerter, R.O.

    1995-01-01

    About twenty years ago, A. W. Maschke of Brookhaven National Laboratory and R. L. Martin of Argonne National Laboratory recognized that the accelerators that have been developed for high energy and nuclear physics are, in many ways, ideally suited to the requirements of inertial fusion power production. These accelerators are reliable, they have a long operating life, and they can be efficient. Maschke and Martin noted that they can focus ion beams to small focal spots over distances of many meters and that they can readily operate at the high pulse repetition rates needed for commercial power production. Fusion, however, does impose some important new constraints that are not important for high energy or nuclear physics applications. The most challenging new constraint from a scientific standpoint is the requirement that the accelerator deliver more than 10 14 W of beam power to a small quantity (less than 100 mg) of matter. The most challenging constraint from an engineering standpoint is accelerator cost. Maschke showed theoretically that accelerators could produce adequate work. Heavy-ion fusion is widely recognized to be a promising approach to inertial fusion power production. It provides an excellent opportunity to apply methods and technology developed for basic science to an important societal need. The pulsed-power community has developed a complementary, parallel approach to ion beam fusion known as light-ion fusion. The talk will discuss both heavy-ion and light-ion fusion. It will explain target physics requirements and show how they lead to constraints on the usual accelerator parameters such as kinetic energy, current, and emittance. The talk will discuss experiments that are presently underway, specifically experiments on high-current ion sources and injectors, pulsed-power machines recirculating induction accelerators, and transverse beam combining. The talk will give a brief description of a proposed new accelerator called Elise

  1. Ion-selective electrode reviews

    CERN Document Server

    Thomas, J D R

    1985-01-01

    Ion-Selective Electrode Reviews, Volume 7 is a collection of papers that covers the applications of electrochemical sensors, along with the versatility of ion-selective electrodes. The coverage of the text includes solid contact in membrane ion-selective electrodes; immobilized enzyme probes for determining inhibitors; potentiometric titrations based on ion-pair formation; and application of ion-selective electrodes in soil science, kinetics, and kinetic analysis. The text will be of great use to chemists and chemical engineers.

  2. Clues From Pluto's Ions

    Science.gov (United States)

    Kohler, Susanna

    2016-05-01

    Nearly a year ago, in July 2015, the New Horizons spacecraft passed by the Pluto system. The wealth of data amassed from that flyby is still being analyzed including data from the Solar Wind Around Pluto (SWAP) instrument. Recent examination of this data has revealedinteresting new information about Plutos atmosphere and how the solar wind interacts with it.A Heavy Ion TailThe solar wind is a constant stream of charged particles released by the Sun at speeds of around 400 km/s (thats 1 million mph!). This wind travels out to the far reaches of the solar system, interacting with the bodies it encounters along the way.By modeling the SWAP detections, the authors determine the directions of the IMF that could produce the heavy ions detected. Red pixels represent IMF directions permitted. No possible IMF could reproduce the detections if the ions are nitrogen (bottom panels), and only retrograde IMF directions can produce the detections if the ions are methane. [Adapted from Zirnstein et al. 2016]New Horizons data has revealed that Plutos atmosphere leaks neutral nitrogen, methane, and carbon monoxide molecules that sometimes escape its weak gravitational pull. These molecules become ionized and are subsequently picked up by the passing solar wind, forming a tail of heavy ions behind Pluto. The details of the geometry and composition of this tail, however, had not yet been determined.Escaping MethaneIn a recent study led by Eric Zirnstein (Southwest Research Institute), the latest analysis of data from the SWAP instrument on board New Horizons is reported. The team used SWAPs ion detections from just after New Horizons closest approach to Pluto to better understand how the heavy ions around Pluto behave, and how the solar wind interacts with Plutos atmosphere.In the process of analyzing the SWAP data, Zirnstein and collaborators first establish what the majority of the heavy ions picked up by the solar wind are. Models of the SWAP detections indicate they are unlikely

  3. Study of ion exchange equilibrium and determination of heat of ion exchange by ion chromatography

    International Nuclear Information System (INIS)

    Liu Kailu; Yang Wenying

    1996-01-01

    Ion chromatography using pellicularia ion exchange resins and dilute solution can be devoted to the study of ion exchange thermodynamics and kinetics. Ion exchange equilibrium equation was obtained, and examined by the experiments. Based on ion exchange equilibrium, the influence of eluent concentration and resin capacity on adjusted retention volumes was examined. The effect of temperature on adjusted retention volumes was investigated and heats of ion exchange of seven anions were determined by ion chromatography. The interaction between anions and skeleton structure of resins were observed

  4. Ion nitriding of aluminium

    International Nuclear Information System (INIS)

    Fitz, T.

    2002-09-01

    The present study is devoted to the investigation of the mechanism of aluminium nitriding by a technique that employs implantation of low-energy nitrogen ions and diffusional transport of atoms. The nitriding of aluminium is investigated, because this is a method for surface modification of aluminium and has a potential for application in a broad spectrum of fields such as automobile, marine, aviation, space technologies, etc. However, at present nitriding of aluminium does not find any large scale industrial application, due to problems in the formation of stoichiometric aluminium nitride layers with a sufficient thickness and good quality. For the purposes of this study, ion nitriding is chosen, as an ion beam method with the advantage of good and independent control over the process parameters, which thus can be related uniquely to the physical properties of the resulting layers. Moreover, ion nitriding has a close similarity to plasma nitriding and plasma immersion ion implantation, which are methods with a potential for industrial application. (orig.)

  5. The ion circus

    Energy Technology Data Exchange (ETDEWEB)

    Minaya Ramirez, Enrique [GSI Helmholtzzentrum, Darmstadt (Germany); Lunney, David [CSNSM- IN2P3/CNRS, Universite de Paris-Sud, Orsay (France)

    2010-07-01

    The ability to prepare radioactive beams for experiments in nuclear structure has seen important developments in recent years. The use of ion traps and buffer-gas cooling now enables the accumulation and purification of even short-lived nuclides. This is a key point for future installations since higher intensity also brings increased isobaric contamination which can be disastrous for background. Until now, the development of beam cooler/bunchers has relied on linear (radiofrequency quadrupole) Paul traps. In this contribution we describe the progress in developing a novel circular Paul trap. The ion circus, so named for its ability to trap ions at different positions along the ring circumference and to eject them in either perpendicular or tangential direction, has also been designed to cool and mass separate the ions over a longer flight path. The resolving power is increased as the ions orbit in the ring and are cooled with buffer gas at a much lower pressure. The first prototype is now under test in Orsay. We report results of the first tests and the future program.

  6. Inverted magnetron ion source

    International Nuclear Information System (INIS)

    Singh, B.; Boyarsky, D.

    1985-01-01

    The present invention provides, in a preferred embodiment, a cylindrical stainless steel cathode with end pieces thereon to form a cathode chamber within. In addition, in a preferred embodiment, there is a stainless steel rod which passes axially through the cathode chamber and which is electrically insulated therefrom at the end pieces. The stainless steel cathode has first and second apertures formed therein with the first to be connected to a source of ionizable gas and the second to act as the opening through which there passes a stream of ions to an ion beam target. A magnetic flux source is coupled to the cathode chamber to pass magnetic flux therethrough and a voltage source is connected between the anode and the cathode to provide an electrostatic field therebetween whereby when ionizable gas is fed into the cathode chamber, it is ionized and a stream of ions emanates from the second aperture. In a preferred embodiment there is further provided an electrostatic ion focusing means to focus the ion stream emanating from the second aperture

  7. Majority ion heating near the ion-ion hybrid layer in tokamaks

    International Nuclear Information System (INIS)

    Phillips, C.K.; Hosea, J.C.; Ignat, D.; Majeski, R.; Rogers, J.H.; Schilling, G.; Wilson, J.R.

    1995-08-01

    Efficient direct majority ion heating in a deuterium-tritium (D-T) reactor-grade plasma via absorption of fast magnetosonic waves in the ion cyclotron range of frequencies (ICRF) is discussed. Majority ion heating results from resonance overlap between the cyclotron layers and the D-T ion-ion hybrid layer in hot, dense plasmas for fast waves launched with high parallel wavenumbers. Analytic and numerical models are used to explore the regime in ITER plasmas

  8. Ion channels versus ion pumps: the principal difference, in principle.

    Science.gov (United States)

    Gadsby, David C

    2009-05-01

    The incessant traffic of ions across cell membranes is controlled by two kinds of border guards: ion channels and ion pumps. Open channels let selected ions diffuse rapidly down electrical and concentration gradients, whereas ion pumps labour tirelessly to maintain the gradients by consuming energy to slowly move ions thermodynamically uphill. Because of the diametrically opposed tasks and the divergent speeds of channels and pumps, they have traditionally been viewed as completely different entities, as alike as chalk and cheese. But new structural and mechanistic information about both of these classes of molecular machines challenges this comfortable separation and forces its re-evaluation.

  9. Heavy-ion radiography

    International Nuclear Information System (INIS)

    Fabrikant, J.I.; Tobias, C.A.; Holley, W.R.; Benton, E.V.

    1981-01-01

    Heavy-particle radiography has clinical potential as a newly developed noninvasive low-dose imaging procedure that provides increased resolution of minute density differences in soft tissues of the body. The method utilizes accelerated high-energy ions, primarily carbon and neon, at the Bevalac accelerator at the Lawrence Berkeley Laboratory. The research program for medicine utilizes heavy-ion radiography for low-dose mammography, for treatment planning for cancer patients, and for imaging and accurate densitometry of skeletal structures, brain and spinal neoplasms, and the heart. The potential of heavy-ion imaging, and particularly reconstruction tomography, is now proving to be an adjunct to existing diagnostic imaging procedures in medicine, both for applications to the diagnosis, management and treatment of clinical cancer in man, and for the early detection of small soft-tissue tumors at low radiation dose

  10. Heavy ion inertial fusion

    International Nuclear Information System (INIS)

    Keefe, D.; Sessler, A.M.

    1980-01-01

    Inertial fusion has not yet been as well explored as magnetic fusion but can offer certain advantages as an alternative source of electric energy for the future. Present experiments use high-power beams from lasers and light-ion diodes to compress the deuterium-tritium (D-T) pellets but these will probably be unsuitable for a power plant. A more promising method is to use intense heavy-ion beams from accelerator systems similar to those used for nuclear and high-energy physics; the present paper addresses itself to this alternative. As will be demonstrated the very high beam power needed poses new design questions, from the ion-source through the accelerating system, the beam transport system, to the final focus. These problems will require extensive study, both theoretically and experimentally, over the next several years before an optimum design for an inertial fusion driver can be arrived at. (Auth.)

  11. Acceleration of radioactive ions

    International Nuclear Information System (INIS)

    Laxdal, R.E.

    2003-01-01

    There is an intense interest world-wide in the use of radioactive ion beams (RIBs) for experiment. In many existing or proposed facilities ions are produced or collected at source potential, ionized and re-accelerated. Within the past year three new ISOL based facilities have added dedicated post-accelerators to deliver accelerated RIBs to experiment. The paper gives an overview of RIB accelerators present and future, and explores the inherent features in the various acceleration methods with an emphasis on heavy ion linacs. The ISAC-I and ISAC-II post-accelerators are discussed as examples. Commissioning results and initial operating experience with ISAC-I will be presented

  12. Ion accelerators for space

    International Nuclear Information System (INIS)

    Slobodrian, R.J.; Potvin, L.

    1991-01-01

    The main purpose of the accelerators is to allow ion implantation in space stations and their neighborhoods. There are several applications of interest immediately useful in such environment: as ion engines and thrusters, as implanters for material science and for hardening of surfaces (relevant to improve resistance to micrometeorite bombardment of exposed external components), production of man made alloys, etc. The microgravity environment of space stations allows the production of substances (crystalline and amorphous) under conditions unknown on earth, leading to special materials. Ion implantation in situ of those materials would thus lead uninterruptedly to new substances. Accelerators for space require special design. On the one hand it is possible to forego vacuum systems simplifying the design and operation but, on the other hand, it is necessary to pay special attention to heat dissipation. Hence it is necessary to construct a simulator in vacuum to properly test prototypes under conditions prevailing in space

  13. Heavy ion inertial fusion

    International Nuclear Information System (INIS)

    Keefe, D.; Sessler, A.M.

    1980-07-01

    Inertial fusion has not yet been as well explored as magnetic fusion but can offer certain advantages as an alternative source of electric energy for the future. Present experiments use high-power beams from lasers and light-ion diodes to compress the deuterium-tritium (D-T) pellets but these will probably be unsuitable for a power plant. A more promising method is to use intense heavy-ion beams from accelerator systems similar to those used for nuclear and high-energy physics; the present paper addresses itself to this alternative. As will be demonstrated the very high beam power needed poses new design questions, from the ion source through the accelerating system, the beam transport system, to the final focus. These problems will require extensive study, both theoretically and experimentally, over the next several years before an optimum design for an inertial fusion driver can be arrived at

  14. Ion cyclotron resonance heating

    International Nuclear Information System (INIS)

    Tajima, T.

    1982-01-01

    Ion cyclotron resonance heating of plasmas in tokamak and EBT configurations has been studied using 1-2/2 and 2-1/2 dimensional fully self-consistent electromagnetic particle codes. We have tested two major antenna configurations; we have also compared heating efficiencies for one and two ion species plasmas. We model a tokamak plasma with a uniform poloidal field and 1/R toroidal field on a particular q surface. Ion cyclotron waves are excited on the low field side by antennas parallel either to the poloidal direction or to the toroidal direction with different phase velocities. In 2D, minority ion heating (vsub(perpendicular)) and electron heating (vsub(parallel),vsub(perpendicular)) are observed. The exponential electron heating seems due to the decay instability. The minority heating is consistent with mode conversion of fast Alfven waves and heating by electrostatic ion cyclotron modes. Minority heating is stronger with a poloidal antenna. The strong electron heating is accompanied by toroidal current generation. In 1D, no thermal instability was observed and only strong minority heating resulted. For an EBT plasma we model it by a multiple mirror. We have tested heating efficiency with various minority concentrations, temperatures, mirror ratios, and phase velocities. In this geometry we have beach or inverse beach heating associated with the mode conversion layer perpendicular to the toroidal field. No appreciable electron heating is observed. Heating of ions is linear in time. For both tokamak and EBT slight majority heating above the collisional rate is observed due to the second harmonic heating. (author)

  15. Ion-selective electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Mikhelson, Konstantin N. [St. Petersburg State Univ. (Russian Federation). Ion-Selective Electrode Laboratory

    2013-06-01

    Ion-selective electrodes (ISEs) have a wide range of applications in clinical, environmental, food and pharmaceutical analysis as well as further uses in chemistry and life sciences. Based on his profound experience as a researcher in ISEs and a course instructor, the author summarizes current knowledge for advanced teaching and training purposes with a particular focus on ionophore-based ISEs. Coverage includes the basics of measuring with ISEs, essential membrane potential theory and a comprehensive overview of the various classes of ion-selective electrodes. The principles of constructing ISEs are outlined, and the transfer of methods into routine analysis is considered.

  16. Ion beam texturing

    Science.gov (United States)

    Hudson, W. R.

    1977-01-01

    A microscopic surface texture was created by sputter-etching a surface while simultaneously sputter-depositing a lower sputter yield material onto the surface. A xenon ion-beam source was used to perform the texturing process on samples as large as 3-cm diameter. Textured surfaces have been characterized with SEM photomicrographs for a large number of materials including Cu, Al, Si, Ti, Ni, Fe, stainless steel, Au, and Ag. A number of texturing parameters are studied including the variation of texture with ion-beam powder, surface temperature, and the rate of texture growth with sputter etching time.

  17. Magnetic ions in crystals

    CERN Document Server

    Stevens, K W

    2014-01-01

    There have been many demonstrations, particularly for magnetic impurity ions in crystals, that spin-Hamiltonians are able to account for a wide range of experimental results in terms of much smaller numbers of parameters. Yet they were originally derived from crystal field theory, which contains a logical flaw; electrons on the magnetic ions are distinguished from those on the ligands. Thus there is a challenge: to replace crystal field theory with one of equal or greater predictive power that is based on a surer footing. The theory developed in this book begins with a generic Hamiltonian, on

  18. [Relativistic heavy ion research

    International Nuclear Information System (INIS)

    1990-01-01

    At Brookhaven National Laboratory, participation in the E802 Experiment, which is the first major heavy-ion experiment at the BNL-AGS, was the main focus of the group during the past four years. The emphases of the E802 experiment were on (a) accurate particle identification and measurements of spectra over a wide kinematical domain (5 degree LAB < 55 degree, p < 20 GeV/c); and (b) measurements of small-angle two-particle correlations, with event characterization tools: multiplicity array, forward and large-angle calorimeters. This experiment and other heavy ion collision experiments are discussed in this report

  19. Secondary ion emission

    International Nuclear Information System (INIS)

    Krohn, V.E.

    1976-01-01

    The Saha-Langmuir equation that describes the equilibrium emission process, surface ionization, has also been used to describe ion yields observed in the non-equilibrium emission process, sputtering. In describing sputtering, it is probably best to include the potential due to an image charge in the expression for negative as well as positive ion yield and to treat the work function and the temperature as parameters having limited physical significance. Arguments are presented to suggest that sputtered material is not emitted from a plasma. (Auth.)

  20. Heavy ion collisions

    International Nuclear Information System (INIS)

    Jacak, B.V.

    1994-01-01

    Heavy ion collisions at very high energies provide an opportunity to recreate in the laboratory the conditions which existed very early in the universe, just after the big bang. We prepare matter at very high energy density and search for evidence that the quarks and gluons are deconfined. I describe the kinds of observables that are experimentally accessible to characterize the system and to search for evidence of new physics. A wealth of information is now available from CERN and BNL heavy ion experiments. I discuss recent results on two particle correlations, strangeness production, and dilepton and direct photon distributions

  1. Ion-selective electrodes

    CERN Document Server

    Mikhelson, Konstantin N

    2013-01-01

    Ion-selective electrodes (ISEs) have a wide range of applications in clinical, environmental, food and pharmaceutical analysis as well as further uses in chemistry and life sciences. Based on his profound experience as a researcher in ISEs and a course instructor, the author summarizes current knowledge for advanced teaching and training purposes with a particular focus on ionophore-based ISEs. Coverage includes the basics of measuring with ISEs, essential membrane potential theory and a comprehensive overview of the various classes of ion-selective electrodes. The principles of constructing I

  2. Double chamber ion source

    International Nuclear Information System (INIS)

    Uman, M.F.; Winnard, J.R.; Winters, H.F.

    1978-01-01

    The ion source is comprised of two discharge chambers one of which is provided with a filament and an aperture leading into the other chamber which in turn has an extraction orifice. A low voltage arc discharge is operated in an inert gas atmosphere in the filament chamber while an arc of higher voltage is operated in the second ionization chamber which contains a vapor which will give the desired dopant ion species. The entire source is immersed in an axial magnetic field parallel to a line connecting the filament, the aperture between the two chambers and the extraction orifice. (author)

  3. Asymmetric ion trap

    Science.gov (United States)

    Barlow, Stephan E.; Alexander, Michael L.; Follansbee, James C.

    1997-01-01

    An ion trap having two end cap electrodes disposed asymmetrically about a center of a ring electrode. The inner surface of the end cap electrodes are conformed to an asymmetric pair of equipotential lines of the harmonic formed by the application of voltages to the electrodes. The asymmetry of the end cap electrodes allows ejection of charged species through the closer of the two electrodes which in turn allows for simultaneously detecting anions and cations expelled from the ion trap through the use of two detectors charged with opposite polarity.

  4. [Relativistic heavy ion research

    International Nuclear Information System (INIS)

    1991-01-01

    The present document describes our second-year application for a continuation grant on relativistic heavy-ion research at Nevis Laboratories, Columbia University, over the two-year period starting from November 15, 1990. The progress during the current budget year is presented. This year, construction of RHIC officially began. As a result, the entire Nevis nuclear physics group has made a coherent effort to create new proposal for an Open Axially Symmetric Ion Spectrometer (OASIS) proposal. Future perspectives and our plans for this proposal are described

  5. Small Column Ion Exchange

    International Nuclear Information System (INIS)

    Huff, Thomas

    2010-01-01

    Small Column Ion Exchange (SCIX) leverages a suite of technologies developed by DOE across the complex to achieve lifecycle savings. Technologies are applicable to multiple sites. Early testing supported multiple sites. Balance of SRS SCIX testing supports SRS deployment. A forma Systems Engineering Evaluation (SEE) was performed and selected Small Column Ion Exchange columns containing Crystalline Silicotitanate (CST) in a 2-column lead/lag configuration. SEE considered use of Spherical Resorcinol-Formaldehyde (sRF). Advantages of approach at SRS include: (1) no new buildings, (2) low volume of Cs waste in solid form compared to aqueous strip effluent; and availability of downstream processing facilities for immediate processing of spent resin.

  6. Electron capture in ion atom and ion-ion collisions

    International Nuclear Information System (INIS)

    Barat, M.

    1986-01-01

    Electron capture (EC) by positive ions in collision with various targets has remained one of the most important subjects of research since the early 30's. From a theoretical point of view, EC is obviously a coupled 3-body problem: at least two cores and an active electron that jumps between them. Practical interest in EC arose in a variety of fields. Recently a renewed interest arose from the physics of thermonuclear fusion, where capture by highly charged ionic impurities were found to be an important process in tokamak devices. For that reasons, a number of reviews were devoted to this subject during the past years, including lectures given in various NATO advanced science institutes. The aim of this lecture is not at all to add a new review to this list, but (i) to summarize the very basis of the present theoretical approaches at low and moderate collision energy, (ii) to pinpoint some crucial difficulties in the theoretical treatment, (iii) to select specific examples which, to the taste of the author, reflect some present practical interest, or some significant advances. 48 references, 38 figures, 1 table

  7. Ion-selective electrode reviews

    CERN Document Server

    Thomas, J D R

    1982-01-01

    Ion-Selective Electrode Reviews, Volume 3, provides a review of articles on ion-selective electrodes (ISEs). The volume begins with an article on methods based on titration procedures for surfactant analysis, which have been developed for discrete batch operation and for continuous AutoAnalyser use. Separate chapters deal with detection limits of ion-selective electrodes; the possibility of using inorganic ion-exchange materials as ion-sensors; and the effect of solvent on potentials of cells with ion-selective electrodes. Also included is a chapter on advances in calibration procedures, the d

  8. Cooling of molecular ion beams

    International Nuclear Information System (INIS)

    Wolf, A.; Krohn, S.; Kreckel, H.; Lammich, L.; Lange, M.; Strasser, D.; Grieser, M.; Schwalm, D.; Zajfman, D.

    2004-01-01

    An overview of the use of stored ion beams and phase space cooling (electron cooling) is given for the field of molecular physics. Emphasis is given to interactions between molecular ions and electrons studied in the electron cooler: dissociative recombination and, for internally excited molecular ions, electron-induced ro-vibrational cooling. Diagnostic methods for the transverse ion beam properties and for the internal excitation of the molecular ions are discussed, and results for phase space cooling and internal (vibrational) cooling are presented for hydrogen molecular ions

  9. Analytical applications of ion exchangers

    CERN Document Server

    Inczédy, J

    1966-01-01

    Analytical Applications of Ion Exchangers presents the laboratory use of ion-exchange resins. This book discusses the development in the analytical application of ion exchangers. Organized into 10 chapters, this book begins with an overview of the history and significance of ion exchangers for technical purposes. This text then describes the properties of ion exchangers, which are large molecular water-insoluble polyelectrolytes having a cross-linked structure that contains ionic groups. Other chapters consider the theories concerning the operation of ion-exchange resins and investigate th

  10. Development of focused ion beam systems with various ion species

    International Nuclear Information System (INIS)

    Ji Qing; Leung, K.-N.; King, Tsu-Jae; Jiang Ximan; Appleton, Bill R.

    2005-01-01

    Conventional focused ion beam systems employ a liquid-metal ion source (LMIS) to generate high-brightness beams, such as Ga + beams. Recently there has been an increased need for focused ion beams in areas like biological studies, advanced magnetic-film manufacturing and secondary-ion mass spectroscopy (SIMS). In this article, status of development on focused ion beam systems with ion species such as O 2 + , P + , and B + will be reviewed. Compact columns for forming focused ion beams from low energy (∼3keV), to intermediate energy (∼35keV) are discussed. By using focused ion beams, a SOI MOSFET is fabricated entirely without any masks or resist

  11. Energy landscapes for mobile ions in ion conducting solids

    Indian Academy of Sciences (India)

    molecular dynamics (MD) simulations yields quantitative predictions of the ion transport characteristics. As ... Solid electrolytes; bond valence analysis; ion transport in glasses. 1. .... clusters are considered to contribute only to a.c. conduc-.

  12. An RF ion source based primary ion gun for secondary ion mass spectroscopy

    International Nuclear Information System (INIS)

    Menon, Ranjini; Nabhiraj, P.Y.; Bhandari, R.K.

    2011-01-01

    In this article we present the design, development and characterization of an RF plasma based ion gun as a primary ion gun for SIMS application. RF ion sources, in particular Inductively Coupled Plasma (ICP) ion sources are superior compared to LMIS and duoplasmtron ion sources since they are filamentless, can produce ions of gaseous elements. At the same time, ICP ion sources offer high angular current density which is an important factor in producing high current in small spot size on the target. These high current microprobes improve the signal to noise ratio by three orders as compared to low current ion sources such as LMIS. In addition, the high current microprobes have higher surface and depth profiling speeds. In this article we describe a simple ion source in its very basic form, two lens optical column and characteristics of microprobe

  13. Polyatomic ions from a high current ion implanter driven by a liquid metal ion source

    Science.gov (United States)

    Pilz, W.; Laufer, P.; Tajmar, M.; Böttger, R.; Bischoff, L.

    2017-12-01

    High current liquid metal ion sources are well known and found their first application as field emission electric propulsion thrusters in space technology. The aim of this work is the adaption of such kind of sources in broad ion beam technology. Surface patterning based on self-organized nano-structures on, e.g., semiconductor materials formed by heavy mono- or polyatomic ion irradiation from liquid metal (alloy) ion sources (LMAISs) is a very promising technique. LMAISs are nearly the only type of sources delivering polyatomic ions from about half of the periodic table elements. To overcome the lack of only very small treated areas by applying a focused ion beam equipped with such sources, the technology taken from space propulsion systems was transferred into a large single-end ion implanter. The main component is an ion beam injector based on high current LMAISs combined with suited ion optics allocating ion currents in the μA range in a nearly parallel beam of a few mm in diameter. Different types of LMAIS (needle, porous emitter, and capillary) are presented and characterized. The ion beam injector design is specified as well as the implementation of this module into a 200 kV high current ion implanter operating at the HZDR Ion Beam Center. Finally, the obtained results of large area surface modification of Ge using polyatomic Bi2+ ions at room temperature from a GaBi capillary LMAIS will be presented and discussed.

  14. Heavy ion transfer reactions

    International Nuclear Information System (INIS)

    Weisser, D.C.

    1977-06-01

    To complement discussions on the role of γ rays in heavy ion induced reactions, the author discusses the role played by particle detection. Transfer reactions are part of this subject and are among those in which one infers the properties of the residual nucleus in a reaction by observing the emerging light nucleus. Inelastic scattering ought not be excluded from this subject, although no particles are transferred, because of the role it plays in multistep reactions and in fixing O.M. parameters describing the entrance channel of the reaction. Heavy ion transfer reaction studies have been under study for some years and yet this research is still in its infancy. The experimental techniques are difficult and the demands on theory rigorous. One of the main products of heavy ion research has been the thrust to re-examine the assumptions of reaction theory and now include many effects neglected for light ion analysis. This research has spurred the addition of multistep processes to simple direct processes and coupled channel calculations. (J.R.)

  15. Heavy ion accelerator GANIL

    International Nuclear Information System (INIS)

    1975-04-01

    This article presents GANIL, a large national heavy ion accelerator. The broad problems of nuclear physics, atomic physics, astrophysics and physics of condensed media which can be approached and studied with this machine are discussed first, after which the final construction project is described. The project comprises a circular injector, a separated sector cyclotron up beam stripper, and a second separated cyclotron downstream [fr

  16. Requirements for Ion Sources

    International Nuclear Information System (INIS)

    Scrivens, R

    2013-01-01

    Ion sources produce beams for a large variety of different physical experiments, industrial processes and medical applications. In order to characterize the beam delivered by them, a list of requirements is necessary. In this chapter the list of principal requirements is specified and definitions for them are given. (author)

  17. Heavy ion fusion

    International Nuclear Information System (INIS)

    Hofmann, Ingo

    1993-01-01

    With controlled thermonuclear fusion holding out the possibility of a prolific and clean new source of energy, the goal remains elusive after many years of continual effort. While the conventional Tokamak route with magnetic confinement continues to hit the headlines, other alternatives are now becoming competitive. One possible solution is to confine the thermonuclear fuel pellet by high power beams. Current research and perspectives for future work in such inertial confinement was the subject of the 'Prospects for Heavy Ion Fusion' European Research Conference held in Aghia Pelaghia, Crete, last year. Its main focus was on the potential of heavy ion accelerators as well as recent advances in target physics with high power lasers and light ion beams. Carlo Rubbia declared that high energy accelerators, with their high efficiency, are the most promising approach to economical fusion energy production. However the need for cost saving in the driver accelerator requires new ideas in target design tailored to the particularities of heavy ion beams, which need to be pushed to the limits of high current and phase space density at the same time

  18. Industrial ion source technology

    Science.gov (United States)

    Kaufman, H. R.; Robinson, R. S.

    1978-01-01

    An analytical model was developed to describe the development of a coned surface texture with ion bombardment and simultaneous deposition of an impurity. A mathematical model of sputter deposition rate from a beveled target was developed in conjuction with the texturing models to provide an important input to that model. The establishment of a general procedure that will allow the treatment of manay different sputtering configurations is outlined. Calculation of cross sections for energetic binary collisions was extened to Ar, Kr.. and Xe with total cross sections for viscosity and diffusion calculated for the interaction energy range from leV to 1000eV. Physical sputtering and reactive ion etching experiments provided experimental data on the operating limits of a broad beam ion source using CF4 as a working gas to produce reactive species in a sputtering beam. Magnetic clustering effects are observed when Al is seeded with Fe and sputtered with Ar(?) ions. Silicon was textured at a micron scale by using a substrate temperature of 600 C.

  19. Ion implantation into diamond

    International Nuclear Information System (INIS)

    Sato, Susumu

    1994-01-01

    The graphitization and the change to amorphous state of diamond surface layer by ion implantation and its characteristics are reported. In the diamond surface, into which more than 10 16 ions/cm 2 was implanted, the diamond crystals are broken, and the structure changes to other carbon structure such as amorphous state or graphite. Accompanying this change of structure, the electric conductivity of the implanted layer shows two discontinuous values due to high resistance and low resistance. This control of structure can be done by the temperature of the base during the ion implantation into diamond. Also it is referred to that by the base temperature during implantation, the mutual change of the structure between amorphous state and graphite can be controlled. The change of the electric resistance and the optical characteristics by the ion implantation into diamond surface, the structural analysis by Raman spectroscopy, and the control of the structure of the implanted layer by the base temperature during implantation are reported. (K.I.)

  20. Application of ion exchangers

    International Nuclear Information System (INIS)

    Markhol, M.

    1985-01-01

    Existing methods of multi-element separation for radiochemical analysis are considered. The majority of existing methods is noted to be based on application of organic and inorganic ion exchangers. Distillation, coprecipitation, extraction as well as combination of the above methods are also used. Concrete flowsheets of multi-element separation are presented