Plutonium and americium separation from salts

International Nuclear Information System (INIS)

Hagan, P.G.; Miner, F.J.

1976-01-01

Salts or materials containing plutonium and americium are dissolved in hydrochloric acid, heated, and contacted with an alkali metal carbonate solution to precipitate plutonium and americium carbonates which are thereafter readily separable from the solution

Analysis of Americium in Transplutonium Process Solutions

International Nuclear Information System (INIS)

Ferguson, R.B.

2001-01-01

One of the more difficult analyses in the transplutonium field is the determination of americium at trace levels in a complex matrix such as a process dissolver solution. Because of these conditions a highly selective separation must precede the measurement of americium. The separation technique should be mechanically simple to permit remote operation with master-slave manipulators. For subsequent americium measurement by the mass spectroscopic isotopic-dilution technique, plutonium and curium interferences must also have been removed

Transmutation of Americium in Fast Neutron Facilities

OpenAIRE

Zhang, Youpeng

2011-01-01

In this thesis, the feasibility to use a medium sized sodium cooled fast reactor fully loaded with MOX fuel for efficient transmutation of americium is investigated by simulating the safety performance of a BN600-type fast reactor loaded with different fractions of americium in the fuel, using the safety parameters obtained with the SERPENT Monte Carlo code. The focus is on americium mainly due to its long-term contribution to the radiotoxicity of spent nuclear fuel and its deterioration on c...

Americium thermodynamic data for the EQ3/6 database

International Nuclear Information System (INIS)

Kerrisk, J.F.

1984-07-01

Existing thermodynamic data for aqueous and solid species of americium have been reviewed and collected in a form that can be used with the EQ3/6 database. Data that are important in solubility calculations for americium at a proposed Yucca Mountain nuclear waste repository were emphasized. Conflicting data exist for americium complexes with carbonates. Essentially no data are available for americium solids or complexes at temperatures greater than 25 0 C. 17 references, 4 figures

Status of Americium-241 recovery at Rocky Flats Plant

International Nuclear Information System (INIS)

Knighton, J.B.; Hagan, P.G.; Navratil, J.D.; Thompson, G.H.

1981-01-01

This paper is presented in two parts: Part I, Molten Salt Extraction of Americium from Molten Plutonium Metal, and Part II, Aqueous Recovery of Americium from Extraction Salts. The Rocky Flats recovery process used for waste salts includes (1) dilute hydrochloric acid dissolution of residues; (2) cation exchange to convert from the chloride to the nitrate system and to remove gross amounts of monovalent impurities; (3) anion exchange separation of plutonium; (4) oxalate precipitation of americium; and (5) calcination of the oxalate at 600 0 C to yield americium oxide. The aqueous process portion describes attempts to improve the recovery of americium. The first part deals with modifications to the cation exchange step; the second describes development of a solvent extractions process that will recovery americium from residues containing aluminium as well as other common impurities. Results of laboratory work are described. 3 figures, 6 tables. (DP)

Americium removal from nitric acid waste streams

International Nuclear Information System (INIS)

Muscatello, A.C.; Navratil, J.D.

1986-01-01

Separations research at the Rocky Flats Plant (RFP) has found ways to significantly improve americium removal from nitric acid (7M) waste streams generated by plutonium purification operations. Partial neutralization of the acid waste followed by solid supported liquid membranes (SLM) are useful in transferring and concentrating americium from nitrate solutions. Specifically, DHDECMP (dihexyl-N,N-diethylcarbamoylmethylphosphonate) supported on Accurel polypropylene hollow fibers assembled in modular form transfers >95% of the americium from high nitrate (6.9M), low acid (0.1M) feeds into 0.25M oxalic acid stripping solution. Maximum permeabilities were observed to be 0.001 cm/sec, consistent with typical values for other systems. The feed:strip volume ratio shows an inverse relationship to the fraction of metal ion transferred. Cation exchangers may be used to concentrate americium from the strip solution. Furthermore, O0D (iB)CMPO (or CMPO) (octylphenyl-N-N-diisobutylcarbamoylmethylphosphine oxide) has been tested in an extraction chromatography mode. Preliminary results show CMPO to be effective in removing americium if the feed is neutralized to 1.0M acidity and iron(III) is complexed with 0.20M oxalic acid. 3 figs

Aqueous Chloride Operations Overview: Plutonium and Americium Purification/Recovery

Energy Technology Data Exchange (ETDEWEB)

Kimball, David Bryan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Skidmore, Bradley Evan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-06-22

Acqueous Chloride mission is to recover plutonium and americium from pyrochemical residues (undesirable form for utilization and storage) and generate plutonium oxide and americium oxide. Plutonium oxide is recycled into Pu metal production flowsheet. It is suitable for storage. Americium oxide is a valuable product, sold through the DOE-OS isotope sales program.

Comparison of molten chloride and fluoride salts potentialities for An/Ln separation by electrodeposition

Energy Technology Data Exchange (ETDEWEB)

Laplace, A.; Peron, F.; Marrot, F.; Lacquement, J. [DRCP/SCPS/LPP - CEA/CEN Valrho - BP 17171 - 30207 Bagnols/Ceze (France)

2008-07-01

The objective of this paper is the comparison of molten fluoride and chloride salts potentialities for Am/Nd separation by electrodeposition on inert cathode, on a purely thermodynamic point of view. The molten LiF-CaF{sub 2} eutectic (77-23 mol.%, at 780 deg. C) was considered for this study. Cyclic voltammetry showed a one step Am(III)/Am reduction at a potential of {approx_equal}+0.5 V vs. Li{sup +}/Li. A potential difference of 290 mV between Am and Nd metallic deposition was estimated by square-wave voltammetry. This Am/Nd potential difference is more important than in molten chlorides (220 mV in the LiCl-KCl eutectic at 500 deg. C). Moreover in molten fluoride salt, the americium and neodymium (+II) oxidation state is not stable contrary to the molten chloride one where corrosion of deposited Am would be potential. However this larger potential difference in molten fluorides is quite balanced by the higher working temperature. (authors)

Biosorption of americium by alginate beads

International Nuclear Information System (INIS)

Borba, Tania Regina de; Marumo, Julio Takehiro; Goes, Marcos Maciel de; Ferreira, Rafael Vicente de Padua; Sakata, Solange Kazumi

2009-01-01

The use of biotechnology to remove heavy metals from wastes plays great potential in treatment of radioactive wastes and therefore the aim of this study was to evaluate the biosorption of americium by alginate beads. Biosorption has been defined as the property of certain biomolecules to bind and remove selected ions or other molecules from aqueous solutions. The calcium alginate beads as biosorbent were prepared and analyzed for americium uptaking. The experiments were performed in different solution activity concentrations, pH and exposure time. The results suggest that biosorption process is more efficient at pH 4 and for 75, 150, 300 Bq/mL and 120 minutes were necessary to remove almost 100% of the americium-241 from the solution. (author)

Recycling of americium

International Nuclear Information System (INIS)

Hagstroem, Ingela

1999-12-01

Separation of actinides from spent nuclear fuel is a part of the process of recycling fissile material. Extracting agents for partitioning the high level liquid waste (HLLW) from conventional PUREX reprocessing is studied. The CTH-process is based on three consecutive extraction cycles. In the first cycle protactinium, uranium, neptunium and plutonium are removed by extraction with di-2-ethylhexyl-phosphoric acid (HDEHP) from a 6 M nitric acid HLLW solution. Distribution ratios for actinides, fission products and corrosion products between HLLW and 1 M HDEHP in an aliphatic diluent have been investigated. To avoid addition of chemicals the acidity is reduced by a tributylphosphate (TBP) extraction cycle. The distribution ratios of elements present in HLLW have been measured between 50 % TBP in an aliphatic diluent and synthetic HLLW in range 0.1-6 M nitric acid. In the third extraction cycle americium and curium are extracted. To separate trivalent actinides from lanthanides a method based on selective stripping of the actinides from 1 M HDEHP is proposed. The aqueous phase containing ammonia, diethylenetriaminepentaacetic acid (DTPA) and lactic acid is recycled in a closed loop after reextraction of the actinides into a second organic phase also containing 1 M HDEHP. Distribution ratios for americium and neodymium have been measured at varying DTPA and lactic acid concentrations and at varying pH. Nitrogen-donor reagents have been shown to have a potential to separate trivalent actinides from lanthanides. 2,2':6,2''-terpyridine as extractant follows the CHON-principle and can in synergy with 2-bromodecanoic acid separate americium from europium. Distribution ratios for americium and europium, in the range of 0.02-0.12 M nitric acid, between nitric acid and 0.02 M terpyridine with 1 M 2-bromodecanoic acid in tert-butylbenzene (TBB) was investigated. Comparison with other nitrogen-donor reagents show that increasing lipophilicity of the molecule, by substitution of

Americium product solidification and disposal

International Nuclear Information System (INIS)

Mailen, J.C.; Campbell, D.O.; Bell, J.T.; Collins, E.D.

1987-01-01

The americium product from the TRUEX processing plant needs to be converted into a form suitable for ultimate disposal. An evaluation of the disposal based on safety, number of process steps, demonstrated operability of the processes, production of low-level alpha waste streams, and simplicity of maintenance with low radiation exposures to personnel during maintenance, has been made. The best process is to load the americium on a cation exchange resin followed by calcination or oxidation of the resin after loading

Uptake of americium-241 by algae and bacteria

Energy Technology Data Exchange (ETDEWEB)

Geisy, J P; Paine, D

1978-01-01

Algae and bacteria are important factors in the transport and mobilization of elements in the biosphere. These factors may be involved in trophic biomagnification, resulting in a potential human hazard or environmental degradation. Although americium, one of the most toxic elements known, is not required for plant growth, it may be concentrated by algae and bacteria. Therefore, the availability of americium-241 to algae and bacteria was studied to determine their role in the ultimate fate of this element released into the environment. Both algae and bacteria concentrated americium-241 to a high degree, making them important parts of the biomagnification process. The ability to concentrate americium-241 makes algae and bacteria potentially significant factors in cycling this element in the water column. (4 graphs, numerous references, 3 tables)

Americium migration in basalt and implications to repository risk analysis

International Nuclear Information System (INIS)

Rickert, P.G.

1980-01-01

Experiments were performed with americium as a minor component in groundwater. Batch adsorption, migration through column, and filtration experiments were performed. It was determined in batch experiments that americium is strongly adsorbed from solution. It was determined with filtration experiments that large percentages of the americium concentrations suspended by the contact solutions in batch experiments and suspended by the infiltrating groundwater in migration experiments were associated with particulate. Filtration was determined to be the primary mode of removal of americium from infiltrating groundwater in a column of granulated basalt (20 to 50 mesh) and an intact core of permeable basalt. Fractionally, 0.46 and 0.22 of the americium component in the infiltrating groundwater was transported through the column and core respectively. In view of these filtration and migration experiment results, the concept of K/sub d/ in the chromatographic sense is meaningless for predicting americium migration in bedrock by groundwater transport at near neutral pH

Recovery and purification of americium from molten salt extraction residues

International Nuclear Information System (INIS)

Navratil, J.D.; Martella, L.L.; Thompson, G.H.

1980-01-01

Americium recovery and purification development at Rocky Flats involves the testing of a combined anion exchange - bidentate organophosphorus liquid - liquid extraction or extraction chromatography process for separating americium from molten salt extraction residues. Laboratory-scale and preliminary pilot-plant results have shown that americium can be effectively recovered and purified from impurity elements such as aluminum, calcium, magnesium, plutonium, potassium, sodium, and zinc. The purified americium oxide product from the liquid - liquid extraction process contained greater than 95% AmO 2 with less than 1% of any individual impurity element

Transmutation of Americium in Fast Neutron Facilities

International Nuclear Information System (INIS)

Zhang, Youpeng

2011-01-01

In this thesis, the feasibility to use a medium sized sodium cooled fast reactor fully loaded with MOX fuel for efficient transmutation of americium is investigated by simulating the safety performance of a BN600-type fast reactor loaded with different fractions of americium in the fuel, using the safety parameters obtained with the SERPENT Monte Carlo code. The focus is on americium mainly due to its long-term contribution to the radiotoxicity of spent nuclear fuel and its deterioration on core's safety parameters. Applying the SAS4A/SASSYS transient analysis code, it is demonstrated that the power rating needs to be reduced by 6% for each percent additional americium introduction into the reference MOX fuel, maintaining 100 K margin to fuel melting, which is the most limiting failure mechanism. Safety analysis of a new Accelerator Driven System design with a smaller pin pitch-to-diameter ratio comparing to the reference EFIT-400 design, aiming at improving neutron source efficiency, was also performed by simulating performance for unprotected loss of flow, unprotected transient overpower, and protected loss-of-heat-sink transients, using neutronic parameters obtained from MCNP calculations. Thanks to the introduction of the austenitic 15/15Ti stainless steel with enhanced creep rupture resistance and acceptable irradiation swelling rate, the suggested ADS design loaded with nitride fuel and cooled by lead-bismuth eutectic could survive the full set of transients, preserving a margin of 130 K to cladding rupture during the most limiting transient. The thesis concludes that efficient transmutation of americium in a medium sized sodium cooled fast reactor loaded with MOX fuel is possible but leads to a severe power penalty. Instead, preserving transmutation rates of minor actinides up to 42 kg/TWh th , the suggested ADS design with enhanced proton source efficiency appears like a better option for americium transmutation

Procedure for the analysis of americium in complex matrices

International Nuclear Information System (INIS)

Knab, D.

1978-02-01

A radioanalytical procedure for the analysis of americium in complex matrices has been developed. Clean separations of americium can be obtained from up to 100 g of sample ash, regardless of the starting material. The ability to analyze large masses of material provides the increased sensitivity necessary to detect americium in many environmental samples. The procedure adequately decontaminates from rare earth elements and natural radioactive nuclides that interfere with the alpha spectrometric measurements

Preparation of americium metal of high purity and determination of the heat of formation of the hydrated trivalent americium ion

International Nuclear Information System (INIS)

Spirlet, J.C.

1975-10-01

In order to redetermine some physical and chemical properties of americium metal, several grams of Am-241 have been prepared by two independent methods: lanthanum reduction of the oxide and thermal dissociation of the intermetallic compound Pt 5 Am. After its separation from excess lanthanum or alloy constituent by evaporation, americium metal was further purified by sublimation at 1100 deg C and 10 -6 Torr. Irrespective of the method of preparation, the americium samples displayed the same d.h.c.p. crystal structure. As determined by vacuum hot extraction, the oxygen, nitrogen and hydrogen contents are equal to or smaller than 250, 50 and 20 ppm, respectively. The heats of solution of americium metal (d.c.h.p. structure) in aqueous hydrochloric acid solutions have been measured at 298.15+-0.05K. The standard enthalpy of formation of Am 3+ (aq) is obtained as -616.7+-1.2 kJ mol -1 [fr

Chemistry of americium

Energy Technology Data Exchange (ETDEWEB)

Schulz, W.W.

1976-01-01

Essential features of the descriptive chemistry of americium are reviewed. Chapter titles are: discovery, atomic and nuclear properties, collateral reading, production and uses, chemistry in aqueous solution, metal, alloys, and compounds, and, recovery, separation, purification. Author and subject indexes are included. (JCB)

Comparative behavior of americium and plutonium in wastewater

International Nuclear Information System (INIS)

Tsvetaeva, N.E.; Filin, V.M.; Ragimov, T.K.; Rudaya, L.Y.; Shapiro, K.Y.; Shcherbakov, B.Y.

1986-01-01

This paper studies the behavior of trace americium and plutoniumin wastewater fed into purification systems. Activities of the elements were determined on a semiconductive alpha-ray spectrometer. the distributio nonuniformity, or heterogeneity, of americium and plutonium per unit volume of wastewater was determined quantitatively before and after passage through filter papers. The two elements were found to be in a colloidal or pseudocolloidal state in the original wastewater sample at pH 6. On acidifying the wastewater from pH 4 to 1 M nitric acid the americium passed quantitatively into the water phase but the most plutonium remained in the colloidal or pseudocolloidal state. the plutonium also passed quantitatively into the water phase in wastewater at a 1 M nitric acid acidity but only after a prolonged (12-day) hold. A knowledge of the heterogeneity of plutonium and americium in wastewaters made it possible to quickly distinguish their state, i.e., colloidal, pseudocolloidal, or in true solution

Formation of americium and europium humate complexes

International Nuclear Information System (INIS)

Minai, Y.; Tominaga, T.; Meguro, Y.

1991-01-01

Binding constants of americium and europium with a humic acid were determined to study if complex formation of trivalent actinide-humates affects dissolved species of the actinides in hydrosphere. The purified humic acid was characterized by means of UV-vis, IR, and pH titration, indicating high carboxylate capacity and low aromaticity. Binding constants of americium and europium humates were determined at pH 4.6 and 6.0 by solvent extraction using 241 Am or 152 Eu as a tracer. The binding constants for americium-humate obtained preliminarily suggest that complexes with humic acid are not negligible in speciation of trivalent actinides in hydrosphere. The obtained binding constants were nearly identical with those determined previously by the same procedures, but with humic acids of different origin and compositions. (author)

PROCESS FOR SEPARATING AMERICIUM AND CURIUM FROM RARE EARTH ELEMENTS

Science.gov (United States)

Baybarz, R.D.; Lloyd, M.H.

1963-02-26

This invention relates to methods of separating americium and curium values from rare earth values. In accordance with the invention americium, curium, and rare earth values are sorbed on an anion exchange resin. A major portion of the rare earth values are selectively stripped from the resin with a concentrated aqueous solution of lithium chloride, and americium, curium, and a minor portion of rare earth values are then stripped from the resin with a dilute aqueous solution of lithium chloride. The americium and curium values are further purified by increasing the concentration of lithium chloride in the solution to at least 8 molar and selectively extracting rare earth values from the resulting solution with a monoalkylphosphoric acid. (AEC)

Plutonium and Americium Geochemistry at Hanford: A Site Wide Review

Energy Technology Data Exchange (ETDEWEB)

Cantrell, Kirk J.; Felmy, Andrew R.

2012-08-23

This report was produced to provide a systematic review of the state-of-knowledge of plutonium and americium geochemistry at the Hanford Site. The report integrates existing knowledge of the subsurface migration behavior of plutonium and americium at the Hanford Site with available information in the scientific literature regarding the geochemistry of plutonium and americium in systems that are environmentally relevant to the Hanford Site. As a part of the report, key research needs are identified and prioritized, with the ultimate goal of developing a science-based capability to quantitatively assess risk at sites contaminated with plutonium and americium at the Hanford Site and the impact of remediation technologies and closure strategies.

Investigation of factors affecting the quality of americium electroplating

International Nuclear Information System (INIS)

Trdin, M.; Benedik, L.; Samardžija, Z.; Pihlar, B.

2012-01-01

Four different electrolyte solutions were used in the electrodeposition of americium and their influences on the quality of the thin layer of deposited americium isotopes in combination with three different cathode disc materials were investigated. The relations between alpha spectral resolution and disc surface properties were established. - Highlights: ► Compared alpha spectra of americium radioisotopes obtained by electrodeposition. ► Various cathode materials and electrolyte solutions were used. ► Homogeneity and peak area resolution were investigated. ► Electron microscope images show surface structure of electrodeposited material.

Measurement of plutonium and americium in molten salt residues

International Nuclear Information System (INIS)

Haas, F.X.; Lawless, J.L.; Herren, W.E.; Hughes, M.E.

1979-01-01

The measurement of plutonium and americium in molten salt residues using a segmented gamma-ray scanning device is described. This system was calibrated using artificially fabricated as well as process generated samples. All samples were calorimetered and the americium to plutonium content of the samples determined by gamma-ray spectroscopy. For the nine samples calorimetered thus far, no significant biases are present in the comparison of the segmented gamma-ray assay and the calorimetric assay. Estimated errors are of the order of 10 percent and is dependent on the americium to plutonium ratio determination

Americium separations from high salt solutions

International Nuclear Information System (INIS)

Barr, Mary E.; Jarvinen, Gordon D.; Schulte, Louis D.; Stark, Peter C.; Chamberlin, Rebecca M.; Abney, Kent D.; Ricketts, Thomas E.; Valdez, Yvette E.; Bartsch, Richard A.

2000-01-01

Americium (III) exhibits an unexpectedly high affinity for anion-exchange material from the high-salt evaporator bottoms solutions--an effect which has not been duplicated using simple salt solutions. Similar behavior is observed for its lanthanide homologue, Nd(III), in complex evaporator bottoms surrogate solutions. There appears to be no single controlling factor--acid concentration, total nitrate concentration or solution ionic strength--which accounts for the approximately 2-fold increase in retention of the trivalent ions from complex solutions relative to simple solutions. Calculation of species activities (i.e., water, proton and nitrate) in such concentrated mixed salt solutions is difficult and of questionable accuracy, but it is likely that the answer to forcing formation of anionic nitrate complexes of americium lies in the relative activities of water and nitrate. From a practical viewpoint, the modest americium removal needs (ca. 50--75%) from nitric acid evaporator bottoms allow sufficient latitude for the use of non-optimized conditions such as running existing columns filled with older, well-used Reillex HPQ. Newer materials, such as HPQ-100 and the experimental bifunctional resins, which exhibit higher distribution coefficients, would allow for either increased Am removal or the use of smaller columns. It is also of interest that one of the experimental neutral-donor solid-support extractants, DHDECMP, exhibits a similarly high level of americium (total alpha) removal from EV bottoms and is much less sensitive to total acid content than commercially-available material

Transmutation of americium in critical reactors

International Nuclear Information System (INIS)

Wallenius, J.

2005-01-01

Already in 1974, a Los Alamos report suggested that the recycling of higher actinides would be detrimental for the safety of critical reactors. Later investigations confirmed this understanding, and stringent limits on the fraction of minor actinides allowed to be present in the fuel of fast neutron reactors were established. In recent years, and in particular in connection with the generation IV initiative, it has been advocated that recycling of americium in critical reactors is not only feasible, but also a recommendable approach. In the present contribution, it is shown, to the contrary, that introduction of americium into reactors with uranium based fuels deteriorates the safety margin of these reactors to a degree that will not allow consumption of the americium sources present in any economically competitive nuclear fuel cycle. Further, it is shown that uranium and thorium free cores with plutonium based fuels may be designed, that features excellent safety characteristics, as long as americium is not present in the feed. Hence, a closed fuel cycle is suggested, that consists of commercial power production in light water reactors, plutonium burning in uranium and thorium free fast neutron critical reactors, and higher actinide consumption in accelerator driven systems with inert matrix fuel. It is argued that such a fuel cycle (being a refinement of the Double Strata fuel cycle proposed by JAERI and further developed by M. Salvatores) provides a minimum cost penalty for implementing P and T under realistic boundary conditions. (author)

Sorption of americium and neptunium by deep-sea sediments

International Nuclear Information System (INIS)

Higgo, J.J.W.; Rees, L.V.C.; Cronan, D.S.

1983-01-01

The sorption and desorption of americium and neptunium by a wide range of deep-sea sediments from natural sea water at 4 0 C has been studied using a carefully controlled batch technique. All the sediments studied should form an excellent barrier to the migration of americium since distribution coefficients were uniformly greater than 10 5 and the sorption-desorption reaction may not be reversible. The sorption of neptunium was reversible and, except for one red clay, the distribution coefficients were greater than 10 3 for all the sediments investigated. Nevertheless the migration of neptunium should also be effectively retarded by most deep-sea sediments even under relatively oxidizing conditions. The neptunium in solution remained in the V oxidation state throughout the experiments. Under the experimental conditions used colloidal americium was trapped by the sediment and solubility did not seem to be the controlling factor in the desorption of americium. (Auth.)

Supported extractant membranes for americium and plutonium recovery

International Nuclear Information System (INIS)

Muscatello, A.C.; Navratil, J.D.; Killion, M.E.; Price, M.Y.

1987-01-01

Solid supported liquid membranes(SLM) are useful in transferring and concentrating americium and plutonium from nitrate solutions. Specifically, DHDECMP(dihexyl-N,N-diethylcarbamoylmethylphosphonate) supported on Accurel or Celgard polypropylene hollow fibers assembled in modular form transfers >95% of the americium and >70% of the plutonium from high nitrate (6.9 M), low acid (0.1 M) feeds into 0.25 M oxalic acid stripping solution. Membranes supporting TBP (tri-n-butylphosphate) also transfer these metal ions. Maximum permeabilities were observed to be 1 x 10 -3 cm sec -1 , similar to the values for other systems. The feed:strip volume ratio shows an inverse relationship to the fraction of metal ion transferred. Cation exchangers may be used to concentrate americium from the strip solution

Recovery of americium-241 from aged plutonium metal

International Nuclear Information System (INIS)

Gray, L.W.; Burney, G.A.; Reilly, T.A.; Wilson, T.W.; McKibben, J.M.

1980-12-01

About 5 kg of ingrown 241 Am was recovered from 850 kg of aged plutonium using a process developed specifically for Savannah River Plant application. The aged plutonium metal was first dissolved in sulfamic acid. Sodium nitrite was added to oxidize the plutonium to Pu(IV) and the residual sulfamate ion was oxidized to nitrogen gas and sulfate. The plutonium and americium were separated by one cycle of solvent extraction. The recovered products were subsequently purified by cation exchange chromatography, precipitated as oxalates, and calcined to the oxides. Plutonium processng was routine. Before cation exchange purification, the aqueous americium solution from solvent extraction was concentrated and stripped of nitric acid. More than 98% of the 241 Am was then recovered from the cation exchange column where it was effectively decontaminated from all major impurities except nickel and chromium. This partially purified product solution was concentrated further by evaporation and then denitrated by reaction with formic acid. Individual batches of americium oxalate were then precipitated, filtered, washed, and calcined. About 98.5% of the americium was recovered. The final product purity averaged 98% 241 AmO 2 ; residual impurities were primarily lead and nickel

Determination of the oxygen-metal-ratio of uranium-americium mixed oxides

International Nuclear Information System (INIS)

Bartscher, W.

1982-01-01

During the dissolution of uranium-americium mixed oxides in phosphoric acid under nitrogen tetravalent uranium is oxidized by tetravalent americium. The obtained hexavalent uranium is determined by constant potential coulometry. The coulombs measured are equivalent to the oxygen in excess of the minimum composition of UO 2 x AmO 1 . 5 . The total uranium content of the sample is determined in a subsequent coulometric titration. The oxygen-metal ratio of the sample can be calculated for a given uranium-americium ratio. An excess of uranium dioxide is necessary in order to suppress the oxidation of water by tetravalent americium. The standard deviation of the method is 0.0017 O/M units. (orig.) [de

1976 Hanford americium-exposure incident: external decontamination procedures

International Nuclear Information System (INIS)

Jech, J.J.; Berry, J.R.; Breitenstein, B.D.

1982-01-01

An accident resulted in the deposition on an injured workman's skin surfaces, in acid-burned areas and in lacerations, of something in excess of 6 mCi americium-241. The external decontamination procedures used, the change in americium content of the skin during the course of treatment, and some of the unusual problems encountered from the extrusion of foreign material and flaking of skin and scar tissue are described

Investigation of factors affecting the quality of americium electroplating.

Science.gov (United States)

Trdin, M; Benedik, L; Samardžija, Z; Pihlar, B

2012-09-01

Four different electrolyte solutions were used in the electrodeposition of americium and their influences on the quality of the thin layer of deposited americium isotopes in combination with three different cathode disc materials were investigated. The relations between alpha spectral resolution and disc surface properties were established. Copyright © 2012 Elsevier Ltd. All rights reserved.

Americium-241 - ED 4308

International Nuclear Information System (INIS)

Ammerich, M.; Frot, P.; Gambini, D.; Gauron, C.; Moureaux, P.; Herbelet, G.; Lahaye, T.; Le Guen, B.; Pihet, P.; Rannou, A.; Vidal, E.

2012-12-01

This sheet presents the characteristics of Americium-241, its origin, and its radio-physical and biological properties. It briefly describes its use in nuclear medicine. It indicates its dosimetric parameters for external exposure, cutaneous contamination, and internal exposure due to acute contamination or to chronic contamination. It indicates and comments the various exposure control techniques: ambient dose rate measurement, surface contamination measurement, atmosphere contamination. It addresses the means of protection: premise design, protection against external exposure and against internal exposure. It describes how areas are delimited and controlled within the premises: regulatory areas, controls to be performed. It addresses the personnel classification, training and medical survey. It addresses the issue of wastes and effluents. It briefly recalls the administrative procedures related to the authorization and declaration of possession and use of sealed and unsealed sources. It indicates regulatory aspects related to the road transport of Americium-241, describes what is to be done in case of incident or accident (for the different types of contamination or exposure)

Research program on development of advanced treatment technology for americium-containing aqueous waste in NUCEF

Energy Technology Data Exchange (ETDEWEB)

Mineo, Hideaki; Matsumura, Tatsuro; Tsubata, Yasuhiro [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1996-10-01

A research program was prepared on the development of an advanced treatment process for the americium-containing concentrated aqueous waste in NUCEF, than allows americium recovery for the reuse and the reduction of TRU waste generation. A preliminary analysis was conducted on the separation requirements based on the components estimated for the waste. An R and D strategy was proposed from the view to reduce TRU waste generated in the processing that the highest priority is given on the control of TRU leakage such as americium into the effluent stream after americium recovery and the minimization of salt used in the separation over the decontamination of impurities from americium. The extraction chromatographic method was selected as a candidate technology for americium separation under the principle to use reagents that are functional in acidic conditions such as bidentate extractants of DHEDECMP, CMPO or diamides, considering the larger flexibilities in process modification and possible multi-component separation with compact equipment and the past achievements on the recovery of kg quantities of americium. Major R and D items extracted are screening and evaluation of extractants for americium and plutonium, optimization of separation conditions, selection of denitration method, equipment developments and development of solidification methods of discarded americium after reuse and of various kinds of separation residues. In order to cope these items, four steps of R and D program were proposed, i.e., fundamental experiment in beaker-scale on screening and evaluation of extractants, flowsheet study in bench-scale using simulated and small amount of americium aqueous waste solution to evaluate candidate process, americium recovery test in iron-shielded cell to be installed in NUCEF. It is objected to make recovery of 100g orders of americium used for research on fundamental TRU fuel properties. (J.P.N.)

Decontaminaion of metals containing plutonium and americium

International Nuclear Information System (INIS)

Seitz, M.G.; Gerding, T.J.; Steindler, M.J.

1979-06-01

Melt-slagging (melt-refining) techniques were evaluated as a decontamination and consolidation step for metals contaminated with oxides of plutonium and americium. Experiments were performed in which mild steel, stainless steel, and nickel contaminated with oxides of plutonium and americium were melted in the presence of silicate slags of various compositions. The metal products were low in contamination, with the plutonium and americium strongly fractionated to the slags. Partition coefficients (plutonium in slag/plutonium in steel) of 7 x 10 6 were measured with boro-silicate slag and of 3 x 10 6 with calcium, magnesium silicate slag. Decontamination of metals containing as much as 14,000 ppM plutonium appears to be as efficient as for metals with plutonium levels of 400 ppM. Staged extraction, that is, a remelting of processed metal with clean slag, results in further decontamination of the metal. The second extraction is effective with either resistance-furnace melting or electric-arc melting. Slag adhering to the metal ingots and in defects within the ingots is in the important contributors to plutonium retained in processed metals. If these sources of plutonium are controlled, the melt-refining process can be used on a large scale to convert highly contaminated metals to homogeneous and compact forms with very low concentrations of plutonium and americium. A conceptual design of a melt-refining process to decontaminate plutonium- and americium-contaminated metals is described. The process includes single-stage refining of contaminated metals to produce a metal product which would have less than 10 nCi/g of TRU-element contamination. Two plant sizes were considered. The smaller conceptual plant processes 77 kg of metal per 8-h period and may be portable.The larger one processes 140 kg of metal per 8-h period, is stationary, and may be near te maximum size that is practical for a metal decontamination process

Distribution of uranium, americium and plutonium in the biomass of freshwater macrophytes

Energy Technology Data Exchange (ETDEWEB)

Zotina, T.A.; Kalacheva, G.S.; Bolsunovsky, A.YA. [Institute of Biophysics SB RAS, Akademgorodok, Krasnoyarsk (Russian Federation)

2010-07-01

Accumulation of uranium ({sup 238}U), americium ({sup 241}Am) and plutonium ({sup 242}Pu) and their distribution in cell compartments and biochemical components of the biomass of aquatic plants Elodea canadensis, Ceratophyllum demersum, Myrioplyllum spicatum and aquatic moss Fontinalis antipyretica have been investigated in laboratory batch experiments. Isotopes of uranium, americium and plutonium taken up from the water by Elodea canadensis apical shoots were mainly absorbed by cell walls, plasmalemma and organelles. A small portion of isotopes (about 6-13 %) could be dissolved in cytoplasm. The major portion (76-92 %) of americium was bound to cell wall cellulose-like polysaccharides of Elodea canadensis, Myriophyllum spicatum, Ceratophyllum demersum and Fontinalis antipyretica, 8-23 % of americium activity was registered in the fraction of proteins and carbohydrates, and just a small portion (< 1%) in lipid fraction. The distribution of plutonium in the biomass fraction of Elodea was similar to that of americium. Hence, americium and plutonium had the highest affinity to cellulose-like polysaccharides in Elodea biomass. Distribution of uranium in the biomass of Elodea differed essentially from that of transuranium elements: a considerable portion of uranium was recorded in the fraction of protein and carbohydrates (51 %). From our data we can assume that uranium has higher affinity to carbohydrates than proteins. (authors)

Distribution of uranium, americium and plutonium in the biomass of freshwater macrophytes

International Nuclear Information System (INIS)

Zotina, T.A.; Kalacheva, G.S.; Bolsunovsky, A.YA.

2010-01-01

Accumulation of uranium ( 238 U), americium ( 241 Am) and plutonium ( 242 Pu) and their distribution in cell compartments and biochemical components of the biomass of aquatic plants Elodea canadensis, Ceratophyllum demersum, Myrioplyllum spicatum and aquatic moss Fontinalis antipyretica have been investigated in laboratory batch experiments. Isotopes of uranium, americium and plutonium taken up from the water by Elodea canadensis apical shoots were mainly absorbed by cell walls, plasmalemma and organelles. A small portion of isotopes (about 6-13 %) could be dissolved in cytoplasm. The major portion (76-92 %) of americium was bound to cell wall cellulose-like polysaccharides of Elodea canadensis, Myriophyllum spicatum, Ceratophyllum demersum and Fontinalis antipyretica, 8-23 % of americium activity was registered in the fraction of proteins and carbohydrates, and just a small portion (< 1%) in lipid fraction. The distribution of plutonium in the biomass fraction of Elodea was similar to that of americium. Hence, americium and plutonium had the highest affinity to cellulose-like polysaccharides in Elodea biomass. Distribution of uranium in the biomass of Elodea differed essentially from that of transuranium elements: a considerable portion of uranium was recorded in the fraction of protein and carbohydrates (51 %). From our data we can assume that uranium has higher affinity to carbohydrates than proteins. (authors)

Analytical separation of americium and curium, using high performance liquid chromatography

International Nuclear Information System (INIS)

Billon, A.

1978-01-01

Americium and curium are separated on a column of cation exchange resin (Aminex) using hydroxyisobutyric acid (α HIBA) as eluent, at a temperature of 80 0 C. Americium and curium were detected in line using their α emission: the separation was performed in a shielded glove box whose setting-up is given. Finally, the time necessary for a separation is comprised between 30 min and 1 hr. The purity of separated fractions was assayed by mass-spectrometry. An application in the determination of isotopic composition of americium and curium in fuels is described

Preparation of americium source for smoke detector

International Nuclear Information System (INIS)

Ramaswami, A.; Singh, R.J.; Manohar, S.B.

1994-01-01

This report describes the method developed for the preparation of 241 Am source for smoke detector. Americium was electrodeposited from iso-propyl alcohol medium on silver backing. Thin layer of gold (few hundred micro gram thick) was plated on the americium source to make it safe for handling. The thickness of plated gold was such that the alpha radiations from the 241 Am source could escape out of the gold layer and cause ionisation in the surrounding air. The performance of the prepared sources were checked in a smoke detector and was found to be satisfactory and comparable to the imported sources. (author). 1 refs., 2 figs., 1 tab

Aqueous Chloride Operations Overview: Plutonium and Americium Purification/Recovery

Energy Technology Data Exchange (ETDEWEB)

Gardner, Kyle Shelton [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Kimball, David Bryan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Skidmore, Bradley Evan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-09-28

These are a set of slides intended for an information session as part of recruiting activities at Brigham Young University. It gives an overview of aqueous chloride operations, specifically on plutonium and americium purification/recovery. This presentation details the steps taken perform these processes, from plutonium size reduction, dissolution, solvent extraction, oxalate precipitation, to calcination. For americium recovery, it details the CLEAR (chloride extraction and actinide recovery) Line, oxalate precipitation and calcination.

Separation of Americium from plutonium, Annex 3; Prilog 3: Odvajanje amercijuma od plutonijuma

Energy Technology Data Exchange (ETDEWEB)

Cvjeticanin, D; Milic, N; Janicijevic, P; Ratkovic, S [Institute of Nuclear Sciences Boris Kidric, Laboratorija za visoku aktivnost, Vinca, Beograd (Serbia and Montenegro)

1963-12-15

Since there was the possibility of working with plutonium milligram quantities, it was possible to study plutonium with contents of americium, which was expected in the about two years old plutonium solutions. Method for separation of the micro quantities of americium and plutonium was needed as well as a multichannel alpha-pulse analyzer. Method for separation of americium from plutonium by thenol trifluoro-acetone (TTA) and anion exchange was adopted.

Extraction of americium from acid aqueous solutions by diethyl-2-hexyl-pyro-phosphoric acid

International Nuclear Information System (INIS)

Guillaume, Bernard

1971-02-01

After having outlined the interesting properties of americium and the difficulties of its recovery, the author reports the study of the mechanism of extraction of americium from acid aqueous solutions by using the diethyl-2hexyl-pyro-phosphoric acid. Several aspects are thus discussed: influence of concentration of H 2 DEHPP, influence of the acidity of the aqueous phase, saturation of extracting agent, influence of the diluting agent, complexing of americium, influence of other cations. In a second part, the author reports the application to the recovery of americium from effluents, and discusses the obtained results

Environmental impact of a teratogenic actinide: a case study of americium-241

Energy Technology Data Exchange (ETDEWEB)

Wang, J.; Yang, J.Y.

1985-10-16

Americium-241 is widely used as a radiation source, but it also has some potential risk if taken into the body. Although the radiotoxicity of americium-241 is small compared to other transuranic actinides, its effects on the reproductive system and on development of the placenta are more damaging than the effects of plutonium-239. A previous report based on a worst-case scenario involving a hypothetical fire accident in a contaminated facility indicated that there could have been a significant impact on nearby residents from a unit release of americium-241 via atmospheric dispersion. However, because the facility is located in a rural region where most drinking water supplies are drawn from private wells, it is believed that deposition of americium-241 from the atmosphere might also have impacts via the groundwater pathway by infiltration of rainwater. In this analysis, a three-dimensional analytical mathematical model is used to assess several aspects of americium-241 contamination of groundwater, including radioactive transformation, advection, dispersion, and soil sorption. Simulation results indicate that no significant radiological impacts would occur to the nearby residents via the groundwater pathway. 15 refs., 2 figs., 2 tabs.

Environmental impact of a teratogenic actinide: a case study of americium-241

International Nuclear Information System (INIS)

Wang, J.; Yang, J.Y.

1985-01-01

Americium-241 is widely used as a radiation source, but it also has some potential risk if taken into the body. Although the radiotoxicity of americium-241 is small compared to other transuranic actinides, its effects on the reproductive system and on development of the placenta are more damaging than the effects of plutonium-239. A previous report based on a worst-case scenario involving a hypothetical fire accident in a contaminated facility indicated that there could have been a significant impact on nearby residents from a unit release of americium-241 via atmospheric dispersion. However, because the facility is located in a rural region where most drinking water supplies are drawn from private wells, it is believed that deposition of americium-241 from the atmosphere might also have impacts via the groundwater pathway by infiltration of rainwater. In this analysis, a three-dimensional analytical mathematical model is used to assess several aspects of americium-241 contamination of groundwater, including radioactive transformation, advection, dispersion, and soil sorption. Simulation results indicate that no significant radiological impacts would occur to the nearby residents via the groundwater pathway. 15 refs., 2 figs., 2 tabs

Modelling of curium and americium behaviour during separation with displacing complexing chromatography

International Nuclear Information System (INIS)

Chuveleva, Eh.A.; Kharitonov, O.V.; Firsova, L.A.

1994-01-01

Certain heavy rare earths, curium and americium were separated by the method of displacement complexing chromatography using DTPA solutions and solutions containing DTPA and citric acid as eluents. Separation factors of rare earths and curium (americium) were calculated. Imitators for curium and americium separation were suggested: thulium for curium elution using 0.025 mol/l DTPA, holmium-for curium elution using 0.025 mol/l DTPA in the presence of 0.025 mol/l citric acid; terbium can serve as the imitator in both cases. 5 refs., 5 figs

Rare earth elements during diagenesis of abyssal sediments: analogies with a transuranic element americium

International Nuclear Information System (INIS)

Boust, D.

1987-03-01

One of the possibilities for the storage of high-level radioactive wastes consists in burying them into abyssal sediments, the sediments being supposed to barrier out radionuclides migration. The objective of the work was to estimate the efficiency of sediment barrier with respect to americium. As there is no americium in abyssal sediments, an indirect approach was used: the behaviour of the rare earth elements, the best natural analogs of americium. They were analysed in a 15 m long core, from the Cap Verde abyssal plateau. The terrigenous phase derived from the African continent was modified by short-term processes (1-1000 years); the intermediate rare earth elements were dissolved. Mineral coatings, enriched in rare earth appeared. After burial, the evolution continued at a much slower rate (10 5 - 10 6 years). The rare elements of the mineral coatings derived from the dissolution of the terrigenous phase and from an additional source, deeper in the sediment column. The fluxes of rare earth elements from sediment to water column were estimated. In suboxic sediments, the dissolved particulate equilibrium was related to redox conditions. The short-term reactivity of americium was studied in laboratory experiments. Simple americium migration models showed that the sediments barrier was totally efficient with respect to americium. In the conditions, neptunium 237 a daughter product of americium 241 could induce fluxes of 10 16 atoms per year per ton of stored waste (10 -8 Ci y-1), during millions years, towards the water column [fr

Biochemical fractionation and cellular distribution of americium and plutonium in the biomass of freshwater macrophytes

International Nuclear Information System (INIS)

Zotina, T.A.; Kalacheva, G.S.; Bolsunovsky, A.Ya.

2011-01-01

Accumulation of americium ( 241 Am) and plutonium ( 238,242 Pu) and their distribution in cell compartments and biochemical components of the biomass of freshwater aquatic plants Elodea canadensis, Ceratophyllum demersum and Myrioplyllum spicatum and aquatic moss Fontinalis antipyretica have been investigated in laboratory experiments. Americium and plutonium taken up from water by Elodea canadensis apical shoots were mainly absorbed by structural components of plant cells (90% for 241 Am; 89% for 238 Pu and 82-87% for 242 Pu). About 10-18% of isotope activity was recorded in the cytosol fraction. The major concentration (76-92%) of americium was bound to cell wall cellulose-like polysaccharides of Elodea canadensis, Myriophyllum spicatum, Ceratophyllum demersum and Fontinalis antipyretica, 8-24% of americium activity was registered in the fraction of proteins and carbohydrates, and just a minor concentration (<1%) in the lipid fraction. The distribution of plutonium in the biomass fractions of Elodea was similar to that of americium. Hence, americium and plutonium had the highest affinity to cellulose-like polysaccharides of cell walls of freshwater submerged macrophytes. (author)

Fluoride absorption: independence from plasma fluoride levels

International Nuclear Information System (INIS)

Whitford, G.M.; Williams, J.L.

1986-01-01

The concept that there are physiologic mechanisms to homeostatically regulate plasma fluoride concentrations has been supported by results in the literature suggesting an inverse relationship between plasma fluoride levels and the absorption of the ion from the gastrointestinal tract of the rat. The validity of the relationship was questioned because of possible problems in the experimental design. The present work used four different methods to evaluate the effect of plasma fluoride levels on the absorption of the ion in rats: (i) the percentage of the daily fluoride intake that was excreted in the urine; (ii) the concentration of fluoride in femur epiphyses; (iii) the net areas under the time-plasma fluoride concentration curves after intragastric fluoride doses; and (iv) the residual amounts or fluoride in the gastrointestinal tracts after the intragastric fluoride doses. None of these methods indicated that plasma fluoride levels influence the rate or the degree or fluoride absorption. It was concluded that, unless extremely high plasma fluoride levels are involved (pharmacologic or toxic doses), the absorption of the ion is independent of plasma levels. The results provide further evidence that plasma fluoride concentrations are not homeostatically regulated

Solution speciation of plutonium and Americium at an Australian legacy radioactive waste disposal site.

Science.gov (United States)

Ikeda-Ohno, Atsushi; Harrison, Jennifer J; Thiruvoth, Sangeeth; Wilsher, Kerry; Wong, Henri K Y; Johansen, Mathew P; Waite, T David; Payne, Timothy E

2014-09-02

During the 1960s, radioactive waste containing small amounts of plutonium (Pu) and americium (Am) was disposed in shallow trenches at the Little Forest Burial Ground (LFBG), located near the southern suburbs of Sydney, Australia. Because of periodic saturation and overflowing of the former disposal trenches, Pu and Am have been transferred from the buried wastes into the surrounding surface soils. The presence of readily detected amounts of Pu and Am in the trench waters provides a unique opportunity to study their aqueous speciation under environmentally relevant conditions. This study aims to comprehensively investigate the chemical speciation of Pu and Am in the trench water by combining fluoride coprecipitation, solvent extraction, particle size fractionation, and thermochemical modeling. The predominant oxidation states of dissolved Pu and Am species were found to be Pu(IV) and Am(III), and large proportions of both actinides (Pu, 97.7%; Am, 86.8%) were associated with mobile colloids in the submicron size range. On the basis of this information, possible management options are assessed.

Pyrochemical investigations into recovering plutonium from americium extraction salt residues

International Nuclear Information System (INIS)

Fife, K.W.; West, M.H.

1987-05-01

Progress into developing a pyrochemical technique for separating and recovering plutonium from spent americium extraction waste salts has concentrated on selective chemical reduction with lanthanum metal and calcium metal and on the solvent extraction of americium with calcium metal. Both techniques are effective for recovering plutonium from the waste salt, although neither appears suitable as a separation technique for recycling a plutonium stream back to mainline purification processes. 17 refs., 13 figs., 2 tabs

Supercritical Fluid Extraction of Plutonium and Americium from Soil

International Nuclear Information System (INIS)

Fox, R.V.; Mincher, B.J.

2002-01-01

Supercritical fluid extraction (SFE) of plutonium and americium from soil was successfully demonstrated using supercritical fluid carbon dioxide solvent augmented with organophosphorus and beta-diketone complexants. Spiked Idaho soils were chemically and radiologically characterized, then extracted with supercritical fluid carbon dioxide at 2,900 psi and 65 C containing varying concentrations of tributyl phosphate (TBP) and thenoyltrifluoroacetone (TTA). A single 45 minute SFE with 2.7 mol% TBP and 3.2 mol% TTA provided as much as 88% ± 6.0 extraction of americium and 69% ± 5.0 extraction of plutonium. Use of 5.3 mol% TBP with 6.8 mol% of the more acidic beta-diketone hexafluoroacetylacetone (HFA) provided 95% ± 3.0 extraction of americium and 83% ± 5.0 extraction of plutonium in a single 45 minute SFE at 3,750 psi and 95 C. Sequential chemical extraction techniques were used to chemically characterize soil partitioning of plutonium and americium in pre-SFE soil samples. Sequential chemical extraction techniques demonstrated that spiked plutonium resides primarily (76.6%) in the sesquioxide fraction with minor amounts being absorbed by the oxidizable fraction (10.6%) and residual fractions (12.8%). Post-SFE soils subjected to sequential chemical extraction characterization demonstrated that 97% of the oxidizable, 78% of the sesquioxide and 80% of the residual plutonium could be removed using SFE. These preliminary results show that SFE may be an effective solvent extraction technique for removal of actinide contaminants from soil

Gut uptake factors for plutonium, americium and curium

International Nuclear Information System (INIS)

Harrison, J.D.

1982-01-01

Data on estimates of the absorption of plutonium, americium and curium from the human gut based on measurements of uptake in other mammalian species are reviewed. It is proposed that for all adult members of the public ingesting low concentrations of plutonium in food and water, 0.05% would be an appropriate value of absorption except when the conditions of exposure are known and a lower value can be justified. For dietary intakes of americium and curium, the available data do not warrant a change from the ICRP value of 0.05%. For newborn children ingesting americium, curium and soluble forms of plutonium, a value of 1% absorption is proposed for the first 3 months of life during which the infant is maintained on a milk diet. It is proposed that a value of 0.5% should be used for the first year of life to take account of the gradual maturation of the gut. In considering the ingestion of insoluble oxides of plutonium by infants, it is proposed that absorption is taken as 0.1% for the first 3 months and 0.05% for the first year. (author)

Uptake of americium-241 by algae and bacteria

Energy Technology Data Exchange (ETDEWEB)

Giesy, Jr, J P; Paine, D [Savannah River Ecology Lab., Aiken, S.C. (USA)

1978-01-01

The uptake of americium by three algae, Scenedesmus obliguus, Selenastrum capricomutum and Chlorella pyrenosdosa and a bacterium Aeromonas hydrophila was studied. Live and fixed cells of each algal species and live bacterial cells were used. It is shown that algae and bacteria concentrate americium 241 to a high degree which makes them important links in the biomagnification phenomenon which may ultimately lead to a human hazard and be potentially important in recycling Am /sup 241/ in the water column and mobilization from sediments. Chemical fixation of algal cells caused increased uptake which indicated that uptake is by passive diffusion and probably due to chemical alteration of surface binding sites.

Synergistic extraction behaviour of americium from simulated acidic waste solutions

International Nuclear Information System (INIS)

Pathak, P.N.; Veeraraghavan, R.; Mohapatra, P.K.; Manchanda, V.K.

1998-01-01

The extraction behaviour of americium has been investigated with mixtures of 3-phenyl-4-benzoyl-5-isoxazolone (PBI) and oxodonors viz. tri-n-butyl phosphate (TBP), tri-n-octyl phosphine oxide (TOPO) and di-n-butyl octanamide (DBOA) using dodecane as the diluent from 1-6 M HNO 3 media. It is observed that D Am remains unaltered with PBI concentration (in the range 0.06-0.1 M) at 1.47 M TBP in the entire range of HNO 3 concentration. PBI and TBP in combination appears more promising compared to other synergistic systems. The possibility of using this mixture for americium removal from high level liquid waste solution has been explored. Extraction studies indicated that prior removal of uranium by 20% TBP in dodecane is helpful in the quantitative recovery of americium in three contacts. Effect of lanthanides on D Am is found to be marginal. (orig.)

Reduction Rates for Higher Americium Oxidation States in Nitric Acid

Energy Technology Data Exchange (ETDEWEB)

Grimes, Travis Shane [Idaho National Lab. (INL), Idaho Falls, ID (United States); Mincher, Bruce Jay [Idaho National Lab. (INL), Idaho Falls, ID (United States); Schmitt, Nicholas C [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-09-30

The stability of hexavalent americium was measured using multiple americium concentrations and nitric acid concentrations after contact with the strong oxidant sodium bismuthate. Contrary to our hypotheses Am(VI) was not reduced faster at higher americium concentrations, and the reduction was only zero-order at short time scales. Attempts to model the reduction kinetics using zero order kinetic models showed Am(VI) reduction in nitric acid is more complex than the autoreduction processes reported by others in perchloric acid. The classical zero-order reduction of Am(VI) was found here only for short times on the order of a few hours. We did show that the rate of Am(V) production was less than the rate of Am(VI) reduction, indicating that some Am(VI) undergoes two electron-reduction to Am(IV). We also monitored the Am(VI) reduction in contact with the organic diluent dodecane. A direct comparison of these results with those in the absence of the organic diluent showed the reduction rates for Am(VI) were not statistically different for both systems. Additional americium oxidations conducted in the presence of Ce(IV)/Ce(III) ions showed that Am(VI) is reduced without the typical growth of Am(V) observed in the systems sans Ce ion. This was an interesting result which suggests a potential new reduction/oxidation pathway for Am in the presence of Ce; however, these results were very preliminary, and will require additional experiments to understand the mechanism by which this occurs. Overall, these studies have shown that hexavalent americium is fundamentally stable enough in nitric acid to run a separations process. However, the complicated nature of the reduction pathways based on the system components is far from being rigorously understood.

Americium Separations from High-Salt Solutions Using Anion Exchange

International Nuclear Information System (INIS)

Barr, Mary E.; Jarvinen, Gordon D.; Stark, Peter C.; Chamberlin, Rebecca M.; Bartsch, Richard A.; Zhang, Z.Y.; Zhao, W.

2001-01-01

The aging of the US nuclear stockpile presents a number of challenges, including the increasing radioactivity of plutonium residues due to the ingrowth of 241 Am from the β-decay of 241 Pu. We investigated parameters that affect the sorption of Am onto anion-exchange resins from concentrated effluents derived from nitric acid processing of plutonium residues. These postevaporator wastes are nearly saturated solutions of acidic nitrate salts, and americium removal is complicated by physical factors, such as solution viscosity and particulates, as well as by the presence of large quantities of competing metals and acid. Single- and double-contact batch distribution coefficients for americium and neodymium from simple and complex surrogate solutions are presented. Varied parameters include the nitrate salt concentration and composition and the nitric acid concentration. We find that under these extremely concentrated conditions, Am(III) removal efficiencies can surpass 50% per contact. Distribution coefficients for both neodymium and americium are insensitive to solution acidity and appear to be driven primarily by low water activities of the solutions

Organic components and plutonium and americium state in soils and soil solutions

International Nuclear Information System (INIS)

Sokolik, G.A.; Ovsyannikova, S.V.; Kimlenko, I.M.

2002-01-01

The fraction composition of humus substances of different type soils and soil solutions have been studied. A distribution of Pu 239, 240 and Am 241 between humus substances fractions of different dispersity and mobility in soil-vegetation cover has been established. It was shown that humus of organic soils fixes plutonium and americium in soil medium in greater extent than humus of mineral soils. That leads to lower migration ability of radionuclides in organic soils. The lower ability of americium to form difficultly soluble organic and organic-mineral complexes and predomination of its anion complexes in soil solutions may be a reason of higher mobility and biological availability of americium in comparison to plutonium during soil-plant transfer (authors)

In-line measurement of plutonium and americium in mixed solutions

International Nuclear Information System (INIS)

Li, T.K.

1981-01-01

A solution assay instrument (SAI) has been developed at the Los Alamos National Laboratory and installed in the plutonium purification and americium recovery process area in the Los Alamos Plutonium Processing Facility. The instrument is designed for accurate, timely, and simultaneous nondestructive analysis of plutonium and americium in process solutions that have a wide range of concentrations and Am/Pu ratios. For a 25-mL sample, the assay precision is 5 g/L within a 2000-s count time

Fluoride varnish or fluoride mouth rinse?

DEFF Research Database (Denmark)

Keller, M K; Klausen, BJ; Twetman, S

2016-01-01

OBJECTIVE: In many Danish communities, school-based fluoride programs are offered to children with high caries risk in adjunct to tooth brushing. The purpose of this field trial was to compare the caries-preventive effectiveness of two different fluoride programs in 6-12 year olds. BASIC RESEARCH...... different schools were enrolled after informed consent and their class unit was randomly allocated to one of two fluoride programs. INTERVENTIONS: One group received a semi-annual fluoride varnish applications (FV) and the other group continued with an existing program with fluoride mouth rinses once per...... in caries development over two years among children participating in a school-based fluoride varnish or mouth rinse program....

Americium/Curium Disposition Life Cycle Planning Study

International Nuclear Information System (INIS)

Jackson, W.N.; Krupa, J.; Stutts, P.; Nester, S.; Raimesch, R.

1998-01-01

At the request of the Department of Energy Savannah River Office (DOE- SR), Westinghouse Savannah River Company (WSRC) evaluated concepts to complete disposition of Americium and Curium (Am/Cm) bearing materials currently located at the Savannah River Site (SRS)

Selective leaching studies of deep-sea sediments loaded with americium, neptunium and plutonium

International Nuclear Information System (INIS)

Cole, T.G.; Higgo, J.J.W.; Cronan, D.S.; Rees, L.V.C.

1984-07-01

A series of selective leaching experiments were undertaken to investigate the solid phase speciation and distribution of americium, neptunium and plutonium which had been experimentally loaded onto different marine sediment types. The chemical leaches employed showed rather poor selectivity but certain trends were evident. Adsorption was not by ion exchange. Americium showed a preferential affinity for carbonate and plutonium for organic matter. Neptunium appeared to have no preferential affinities. Americium was sorbed by acetic acid residues (CaCO 3 removed) and by unleached carbonate-rich sediments with equal efficiency. This indicates that it is able to diversify its solid phase affinity/distribution depending upon which solid phases are available. (author)

On the role of different biocomponents of bile and excretions in the elimination of plutonium and americium from the body

International Nuclear Information System (INIS)

Shvydko, N.S.

1986-01-01

A study was made of the role of biocomponents of bile, urine and feces in the elimination of plutonium and americium from the organism. Plutonium 239 and americium 241 were separated in bile due to higher tropism of plutonium to low molecular weight addends, and of americium, to a protein-containing fraction. The status of plutonium excreted in feces was the same as the physicochemical status of americium. Plutonium 239 and americium 241 eliminated in urine were in a completely ultrafiltered state

Mobility of plutonium and americium through a shallow aquifer in a semiarid region

International Nuclear Information System (INIS)

Penrose, W.R.; Polzer, W.L.; Essington, E.H.; Nelson, D.M.; Orlandini, K.A.

1990-01-01

Treated liquid wastes containing traces of plutonium and americium are released into Mortandad Canyon, within the site of Los Alamos National Laboratory, NM. The wastes infiltrate a small aquifer within the canyon. Although laboratory studies have predicted that the movement of actinides in subsurface environments will be limited to less than a few meters, both plutonium and americium are detectable in monitoring wells as far as 3,390 m downgradient from the discharge. Between the first and last monitoring wells (1.8 and 3.4 km from the discharge), plutonium concentrations decreased exponentially from 1,400 to 0.55 mBq/L. Americium concentrations ranged between 94 and 1,240 mBq/L, but did not appear to vary in a systematic way with distance. Investigation of the properties of the mobile actinides indicates that the plutonium and part of the americium are tightly or irreversibly associated with colloidal material between 25 and 450 nm in size. The colloidally bound actinides are removed only gradually from the groundwater. The fraction of the americium not associated with colloids exists in a low molecular weight form (diameter, ≤ 2 nm) and appears to be a stable, anionic complex of unknown composition. The mobile forms of these actinides defeat the forces that normally act to retard their movement through groundwater systems

Americium-241 and -243 as an ion-engine propellant

International Nuclear Information System (INIS)

Schachter, M.M.

1994-01-01

Commercially available americium-241 and -243 can be obtained as the mixture of the two isotopes in 100-gram quantities--a product of reprocessing spent nuclear powerplant fuel elements along with plutonium. The half-lives of the isotopes are 450 years for the -241 and 8,000 years for the -243 (the plutonium half-life isotope so obtained is 24,000 years). Americium rolled out in thin foil sheets emits alpha-rays (helium-4 ions) and beta-rays--2 valence electrons for each helium ion. Electrons are also considered as ions. As a foil, the americium radiates only a minimal amount of gamma-rays via the Curie effect. With appropriately designed permanent magnet rings insulated with Wood's alloy, the + and - ions can be accelerated from their already 5.5 million electron-Volts to billion and even trillions of electron-Volts by electronic control grids powered by the magnetohydrodynamic effect of electrons and helium ions streaming at the post-rocket nozzle of the ion engine. Protocol for the estimated thrust of this ion rocket engine is more than ten kilograms continuously sustainable for several thousand years

The ingestion of plutonium and americium by range cattle

International Nuclear Information System (INIS)

Blincoe, C.; Bohman, V.R.; Smith, D.D.

1981-01-01

The intake of plutonium and americium in the diet of cattle grazing on plutonium contaminated desert range was determined. Daily feed intake of the grazing animals was also determined so that the amount of nuclides ingested daily could be ascertained. Soil ingested by range cattle constituted the principal and possibly only source of ingested plutonium and americium and resulted in a daily intake of 3600-6600 pCi 238 Pu, 85,000-400,000 pCi 239 Pu, and 11,000-31,000 pCi 241 Am daily. Determining transuranic intake by direct measurement and from the composition and contamination of the diet gave identical results. (author)

The availability of plutonium and americium in Irish Sea sediments for re-dissolution

International Nuclear Information System (INIS)

McDonald, P.; Vives i Batlle, J.; Bousher, A.; Whittall, A.; Chambers, N.

2001-01-01

The availability of plutonium and americium, for re-dissolution from offshore sediments into Irish Sea water, has been examined. Sediments collected from the mud-patch near the Cumbrian coast were characterized in terms of spatial location, particle size, partitioning of radionuclides with respect to physico-chemical bonds and availability of actinides for release into seawater. Sequential extraction investigations revealed that plutonium was predominantly associated with strongly bound sesquioxide and organic complex fractions. Americium was associated mainly with the organic complex fraction, but a significant fraction was in carbonate form. Sediment/water re-dissolution experiments with and without stirring were compared to simulate the effect of disturbing bed sediment. After 1 week, neither set of re-dissolution data provided significant trends between dissolved activity and time. Stirred systems appeared to release 2.5 times more plutonium and americium into seawater than unstirred systems. Measured 239,240Pu and 241Am distribution coefficients (K d values) were both typically approximately 10 5 l kg -1 . 241Am K d values are an order of magnitude lower than previously reported for the north-eastern Irish Sea, but similar to western Irish Sea values. Overall, the fractions of plutonium and americium available for re-dissolution from bed sediment are very low at <0.1%, with proportionally more plutonium being released than americium. These findings lend further support for the extrapolation of laboratory-derived information to environmental conditions

Fluoride release from fluoride varnishes under acidic conditions.

Science.gov (United States)

Lippert, F

2014-01-01

The aim was to investigate the in vitro fluoride release from fluoride varnishes under acidic conditions. Poly(methyl methacrylate) blocks (Perspex, n=3 per group) were painted with 80 ± 5 mg fluoride varnish (n=10) and placed into artificial saliva for 30 min. Then, blocks were placed into either 1% citric acid (pH 2.27) or 0.3% citric acid (pH 3.75) solutions (n=3 per solution and varnish) for 30 min with the solutions being replaced every 5 min. Saliva and acid solutions were analyzed for fluoride content. Data were analyzed using three-way ANOVA (varnish, solution, time). The three-way interaction was significant (p>0.0001). Fluoride release and release patterns varied considerably between varnishes. Fluoride release in saliva varied by a factor of more than 10 between varnishes. Some varnishes (CavityShield, Nupro, ProFluorid, Vanish) showed higher fluoride release in saliva than during the first 5 min of acid exposure, whereas other varnishes (Acclean, Enamel-Pro, MI Varnish, Vella) showed the opposite behavior. There was little difference between acidic solutions. Fluoride release from fluoride varnishes varies considerably and also depends on the dissolution medium. Bearing in mind the limitations of laboratory research, the consumption of acidic drinks after fluoride varnish application should be avoided to optimize the benefit/risk ratio.

Biokinetic study of plutonium and americium associated to the particulates of soil

International Nuclear Information System (INIS)

Espinosa, A.; Aragon, A.; Martinez, J.; Iranzo, C.E.

1996-01-01

The object of this study is to determine the biokinetic parameters of different Plutonium isotopes and Americium inhaled in the state in which they are found in the environment as a result of their deposition in the soil, from an aviation accident that generated different plutonium oxides. to achieve this objective, two lines of work planned. One was the determination of the mineralogical composition and associations that plutonium and americium present in that soil 22 years after the nuclear accident. Other studies were directed to determine the biokinetic of the plutonium isotopes and americium (contained in the dust) deposited tracheally and inhaled by laboratory animals (rats) and in vitro experiments by pulmonary leaching simulation. The in vivo tests have been developed in NRPB (U.K.) and the in vitro experiment, geochemical associations studies, assessment of internal doses to humans resulting from intake of plutonium and americium bearing dusts present in the contaminated area and establishment of ALIs for inhalation, were carried out in CIEMAT (Spain). In this work only determinations and experiments carried out by CIEMAT are includes as a part of the EU Project ''INHALATION AND INGESTION OF RADIONUCLIDES'' contract: FI3P-CT920064a. (Author) 10 refs

Determination of specific activity of americium and plutonium in selected environmental samples

International Nuclear Information System (INIS)

Trebunova, T.

1999-01-01

The aim of this work was development of method for determination of americium and plutonium in environmental samples. Developed method was evaluated on soil samples and after they was applied on selected samples of fishes (smoked mackerel, herring and fillet from Alaska hake). The method for separation of americium is based on liquid separation with Aliquate-336, precipitation with oxalic acid and using of chromatographic material TRU-Spec TM .The intervals of radiochemical yields were from 13.0% to 80.9% for plutonium-236 and from 10.5% to 100% for americium-241. Determined specific activities of plutonium-239,240 were from (2.3 ± 1.4) mBq/kg to (82 ± 29) mBq/kg, the specific activities of plutonium-238 were from (14.2 ± 3.7) mBq/kg to (708 ± 86) mBq/kg. The specific activities of americium-241 were from (1.4 ± 0.9) mBq/kg to (3360 ± 210) mBq/kg. The fishes from Baltic Sea as well as from North Sea show highest specific activities then fresh-water fishes from Slovakia. Therefore the monitoring of alpha radionuclides in foods imported from territories with nuclear testing is recommended

Fluoridated Water

Science.gov (United States)

... Genetics Services Directory Cancer Prevention Overview Research Fluoridated Water On This Page What is fluoride, and where is it found? What is water fluoridation? When did water fluoridation begin in the ...

1976 Hanford americium exposure incident: psychological aspects

International Nuclear Information System (INIS)

Brown, W.R.

1982-01-01

Accidents involving exposure to radiation or radioactive materials may involve an unusual degree of emotional trauma. Methods that may be employed in dealing with such trauma are discussed in relation to a specific accident in which a radiation worker was injured and seriously contaminated with americium-241

Influence of organic components on plutonium and americium speciation in soils and soil solutions

International Nuclear Information System (INIS)

Sokolik, G.A.; Ovsyannikova, S.V.; Kimlenko, I.M.

2003-01-01

Group composition of humic substances of organic and mineral soils sampled in the 30-km zone of the Chernobyl accident was analyzed for studying influence of organic components on migration properties of plutonium and americium in soils and soil solutions by the method of gel-chromatography and chemical fractionation. It was ascertained that humus of organic soils binds plutonium and americium stronger than humus of mineral soils. Elevated mobility of americium compared to plutonium one stems from lower ability of the latter to from hard to solve organic and organomineral complexes, as well as from its ability to form anionic complexes in soil solutions [ru

Carbamoyl methylphosphine oxide derivatives of adamantane as americium and europium extractants

International Nuclear Information System (INIS)

Babain, V.A.; Alyapyshev, M.Yu.; Novakov, I.A.; Orlinson, B.S.; Savel'ev, E.N.; Shokova, Eh.A.; Serebrayannikova, A.E.; Kovalev, V.V.

2007-01-01

Adamantane di-1,3-carbamoyl methylphosphine oxide (CMPO) derivatives, where CMPO-groups connect with 1,3-positions of rigid adamantane platform by methylene and ethylene bridges, are synthesized, and their efficiency as extractants of americium(III) and europium(III) from nitric acid solutions is demonstrated. Distribution function of Am 3+ and Eu + during extraction from 3M HNO 3 are measured in the investigation of extraction properties. It is noted that first synthesized adamantane CMPO derivatives are more effective for the extraction of americium(III) and europium(III) from 3MHNO 3 [ru

Radiation protection data sheets for the use of Americium 241 in unsealed sources

International Nuclear Information System (INIS)

Anon.

1993-01-01

This radiation protection data sheet is intended for supervisors and staff in the different medical, hospital, pharmaceutical, university and industrial laboratories and departments where Americium 241 is handled, and also for all those involved in risk prevention in this field. It provides essential data on radiation protection measures during the use of Americium 241 in unsealed sources: physical characteristics, risk assessment, administrative procedures, recommendations, regulations and bibliography

Adsorption-desorption characteristics of plutonium and americium with sediment particles in the estuarine environment: studies using plutonium-237 and americium-241

International Nuclear Information System (INIS)

Murray, C.N.; Fukai, R.

1975-01-01

The particle formation of plutonium and americium, their adsorption onto fresh water sediments and the desorption from the sediments in sea water were studied in the Laboratory under simulated river-estuary conditions, using γ-emitting plutonium-237 and americium-241. The results of the experiments show that the particle formation of plutonium depends on its valence states, on pH and on the salinity of the medium. For river water at pH4, some 25%, 20% and 30% of the added 237 Pu was in particulate form, larger than 0.45 μm, for Pu (III), Pu (IV) and Pu (VI), respectively, while 65%, 90% and 50% of the respective valence states was associated with particles at pH 8. In sea water the general pattern remains similar, although Pu (VI) is more soluble in sea water owing to higher ligand concentrations for carbonate and bicarbonate complexes. The pH-dependency of particle formation of Am (III) is more steep than that of plutonium and seems to be influenced by colloidal substances occurring in the experimental media. The adsorption-desorption characteristics of plutonium and americium with the sediment in river water as well as sea water reflect the characteristics of their particle formation, being dependent upon such properties as valence states, the pH and salinity of the medium. A sewage effluent added to the media has small but measurable effects on the adsorption-desorption processes of plutonium. (author)

Local Structure in Americium and Californium Hexa-cyanoferrates - Comparison with Their Lanthanide Analogues

International Nuclear Information System (INIS)

Dupouy, G.; Bonhoure, I.; Dumas, Th.; Moisy, Ph.; Petit, S.; Den Auwer, Ch.; Conradson, St.D.; Hennig, Ch.; Scheinost, A.C.; Le Naour, C.; Simoni, E.

2011-01-01

Metal hexa-cyanoferrates are well known molecular solids for a large variety of cations, although very little has been described for actinide adducts. Two new members of actinide(III) hexa-cyanoferrates were synthesized with the cations americium and californium. They were structurally characterized by infrared and X-ray absorption spectroscopy. Combined EXAFS data at the iron K edge and actinide L 3 edge provide evidence for a three-dimensional model for these two new compounds. Structural data in terms of bond lengths were compared to those reported for the parent lanthanide(III) compounds, neodymium and gadolinium hexa-cyanoferrates, respectively: the americium compound with (KNd(III)Fe(II)-Fe-III(CN) 6 .4H 2 O and the californium compound with (KGd(III)Fe(II)(CN) . 3.5H 2 O and (KGd(III)Fe(II)(CN) 6 .3H 2 O. This comparison between actinide and lanthanide homologues has been carried out on the basis of ionic radii considerations. The americium and neodymium environments appear to be very similar and are arranged in a tri-capped trigonal prism polyhedron of coordination number 9 (CN: 9), in which the americium atom is bonded to six nitrogen atoms and to three water molecules. For the californium adduct, a similar comparison and bond length and angle values derived from EXAFS studies suggest that the californium cation sits in a bi-capped trigonal prism (CN: 8) as in (KGd(III)Fe(II)(CN) 6 . 3H 2 O. This arrangement differs from that in the structure of (KGd(III)Fe(II)(CN) 6 .3.5H 2 O, in which the gadolinium atom is surrounded by 9 atoms. This is one of the rare pieces of information revealed by EXAFS spectroscopy for americium and californium in comparison to lanthanide atoms in molecular solid compounds. A discussion on the decrease in bond length and coordination number from americium to californium is also provided, on the basis of crystallographic results reported in the literature for actinide(III) and lanthanide(III) hydrate series. (authors)

Remobilization of americium in soil columns under experimental rhizo-spheric conditions

Energy Technology Data Exchange (ETDEWEB)

Perrier, T.; Martin-Garin, A.; Morello, M. [CEA Cadarache (DEI/SECRE/LRE), Laboratory of Radioecology and Ecotoxicology, Institute for Radioprotection and Nuclear Safety, 13 - Saint-Paul-lez-Durance (France)

2004-07-01

The biogeochemical behaviour of americium in subsurface soils plays a dominant role on the potential migration of this actinide, but is currently poorly known. The identification and understanding of these processes is of major concern for this highly (radio)toxic element and can allow the determination of its impact on the natural media. This research investigates the relevant processes controlling americium biogeochemical speciation in the rhizosphere of an agricultural soil. Lixiviation tests were performed on columns packed with a 2 mm-sieved calcareous soil contaminated with {sup 241}Am (500 Bq.g{sup -1}), under steady-state unsaturated or saturated hydric flow conditions. The columns were percolated with soil solution of varied compositions, containing citrate and/or glucose simulating root exudates in non-sterile conditions. The physico-chemical parameters of the outlet solution (pH, conductivity, major ions, organic acids) were monitored, as well as the microbial activity. Inorganic and organic speciation of {sup 241}Am is supported by geochemical modeling with JChess, using a thermodynamic database based on NEA database and the latest PSI recommendations. The percolation of a solution in equilibrium with the soil released small amount of americium (<5 mBq/cm{sup 3}), as predicted by the high {sup 241}Am K{sub d} values. 10{sup -4} M concentrations of citrate, glucose or both combined did not enhance remobilization either. Poor remobilization was also observed at high glucose concentrations (10{sup -2} M), despite an effective glucose microbial degradation, the production of ligands such as acetate, and important changes in the chemistry of the solution. On the contrary, high concentrations of citrate (10{sup -2} M) released 1000 times more americium, which is in accordance with previous studies. Even greater releases (10000 times) were observed when 10{sup -2} M glucose was added to 10{sup -2} M citrate. The remobilization of americium resulting from the

1976 Hanford americium exposure incident: overview and perspective

International Nuclear Information System (INIS)

Thompson, R.C.

1982-01-01

Salient features of the 1976 Hanford americium exposure incident are discussed. Comparisons are made with previous human and animal exposure data, and conclusions drawn relative to the injured workman, to health physics practices, and to the adequacy of current exposure limits

Plutonium-239 and americium-241 uptake by plants from soil. Final report

International Nuclear Information System (INIS)

Brown, K.W.

1979-03-01

Alfalfa was grown in soil contaminated with plutonium-239 dioxide (239PuO2) at a concentration of 29.7 nanocuries per gram (nCi/g). In addition to alfalfa, radishes, wheat, rye, and tomatoes were grown in soils contaminated with americium-241 nitrate (241Am(NO3)3) at a concentration of 189 nCi/g. The length of exposure varied from 52 days for the radishes to 237 days for the alfalfa. The magnitude of plutonium incorporation by the alfalfa as indicated by the concentration ratio, 0.0000025, was similar to previously reported data using other chemical forms of plutonium. The results did indicate, however, that differences in the biological availability of plutonium isotopes do exist. All of the species exposed to americium-241 assimilated and translocated this radioisotope to the stem, leaf, and fruiting structures. The magnitude of incorporation as signified by the concentration ratios varied from 0.00001 for the wheat grass to 0.0152 for the radishes. An increase in the uptake of americium also occurred as a function of time for four of the five plant species. Evidence indicates that the predominant factor in plutonium and americium uptake by plants may involve the chelation of these elements in soils by the action of compounds such as citric acid and/or other similar chelating agents released from plant roots

Urinary fluoride excretion after application of fluoride varnish and use of fluoride toothpaste in young children

DEFF Research Database (Denmark)

Lockner, Frida; Twetman, Svante; Stecksén-Blicks, Christina

2017-01-01

BACKGROUND: The efficacy and safety of combined use of topical fluoride products are essential issues that must be monitored. AIM: To assess urinary excretion of fluoride after application of two different dental varnishes containing 2.26% fluoride in 3- to 4-year-old children and to compare...... the levels with and without parallel use of fluoride toothpaste. DESIGN: Fifteen healthy children were enrolled to a randomized crossover trial that was performed in two parts: Part I with twice-daily tooth brushing with fluoride toothpaste and Part II with twice-daily brushing with a non-fluoride toothpaste....... After a 1-week run-in period, 0.1 mL of the two fluoride varnishes (Duraphat and Profluorid Varnish) was topically applied in a randomized order. Baseline and experimental urine was collected during 6-h periods. The fluoride content was determined with an ion-sensitive electrode. RESULTS...

Kinetics of americium(VI) mass transfer through solid supported liquid membrane with HDEHP

International Nuclear Information System (INIS)

Mikheeva, M.N.; Novicoov, P.; Myasoedov, B.F.; Tikhomirov, S.V.

1994-01-01

The main regularities of membrane extraction of americium under conditions of different redox potentials in aqueous phases have been studied. The physico-chemical model of the process including steps of americium oxidation in feed solution, extraction by membrane, partial reduction on membrane surface, trans-membrane diffusion and reextraction to strip solution has been developed. The calculation of reduction rate constant on membrane surface has been carried out. (author) 9 refs.; 4 figs.; 3 tabs

On the structure of thorium and americium adenosine triphosphate complexes

International Nuclear Information System (INIS)

Mostapha, Sarah; Berton, Laurence; Boubals, Nathalie; Zorz, Nicole; Charbonnel, Marie-Christine; Fontaine-Vive, Fabien; Den Auwer, Christophe; Solari, Pier Lorenzo

2014-01-01

The actinides are chemical poisons and radiological hazards. One challenge to better appraise their toxicity and develop countermeasures in case of exposure of living organisms is to better assess pathways of contamination. Because of the high chemical affinity of those actinide elements for phosphate groups and the ubiquity of such chemical functions in biochemistry, nucleotides and in particular adenosine triphosphate nucleotide (ATP) may be considered critical target building blocks for actinides. Combinations of spectroscopic techniques (Fourier transformed Infra Red [FTIR], Electro-spray Ionization Mass Spectrometry [ESI-MS], and Extended X-ray Absorption Fine Structure [EXAFS]) with quantum chemical calculations have been implemented in order to assess the actinides coordination arrangement with ATP. We describe and compare herein the interaction of ATP with thorium and americium; thorium(IV) as a representative of actinide(IV) like plutonium(IV) and americium(III) as a representative of all heavier actinides. In the case of thorium, an insoluble complex is readily formed. In the case of americium, a behavior identical to that described previously for lutetium has been observed with insoluble and soluble complexes. The comparative study of ATP complexation with Th(IV) and Am(III) shows their ability to form insoluble complexes for which a structural model has been proposed by analogy with previously described Lu(III) complexes. (authors)

On the structure of thorium and americium adenosine triphosphate complexes.

Science.gov (United States)

Mostapha, Sarah; Fontaine-Vive, Fabien; Berthon, Laurence; Boubals, Nathalie; Zorz, Nicole; Solari, Pier Lorenzo; Charbonnel, Marie Christine; Den Auwer, Christophe

2014-11-01

The actinides are chemical poisons and radiological hazards. One challenge to better appraise their toxicity and develop countermeasures in case of exposure of living organisms is to better assess pathways of contamination. Because of the high chemical affinity of those actinide elements for phosphate groups and the ubiquity of such chemical functions in biochemistry, nucleotides and in particular adenosine triphosphate nucleotide (ATP) may be considered critical target building blocks for actinides. Combinations of spectroscopic techniques (Fourier transformed Infra Red [FTIR], Electrospray Ionization Mass Spectrometry [ESI-MS], and Extended X-ray Absorption Fine Structure [EXAFS]) with quantum chemical calculations have been implemented in order to assess the actinides coordination arrangement with ATP. We describe and compare herein the interaction of ATP with thorium and americium; thorium(IV) as a representative of actinide(IV) like plutonium(IV) and americium(III) as a representative of all heavier actinides. In the case of thorium, an insoluble complex is readily formed. In the case of americium, a behavior identical to that described previously for lutetium has been observed with insoluble and soluble complexes. The comparative study of ATP complexation with Th(IV) and Am(III) shows their ability to form insoluble complexes for which a structural model has been proposed by analogy with previously described Lu(III) complexes.

Airborne plutonium-239 and americium-241 concentrations measured from the 125-meter Hanford Meteorological Tower

International Nuclear Information System (INIS)

Sehmel, G.A.

1978-01-01

Airborne plutonium-239 and americium-241 concentrations and fluxes were measured at six heights from 1.9 to 122 m on the Hanford meteorological tower. The data show that plutonium-239 was transported on nonrespirable and small particles at all heights. Airborne americium-241 concentrations on small particles were maximum at the 91 m height

Environmental impacts of the release of a transuranic actinide, americium-241, from a contaminated facility

Energy Technology Data Exchange (ETDEWEB)

Want, J.; Merry-Libby, P.

1985-10-29

Americium-241 is widely used as a radiation source, but it also has some potential risk if taken into the body because of its high dose conversion factor. Although the radiotoxicity of americium-241 is small compared to other transuranic actinides, its effects on the reproductive system and on development of the placenta are more damaging than the effects of plutonium-239. In Ohio, a gemologist's laboratory was contaminated with americium-241. Prior to decontamination of the laboratory, potential radiological impacts to the surrounding environment were assessed. A hypothetical fire accident resulting in a unit release (1 curie) was assumed. Potential radiological impacts were simulated using an atmospheric dispersion and dosimetry model with local meteorological data, population census data, and detailed information regarding the neighborhood. The results indicate that there could have been a significant impact on nearby residents from americium-241 via atmospheric dispersion if a major catastrophic release had occurred prior to contamination and decommissioning of the laboratory. 14 refs., 3 figs., 2 tabs.

Airborne plutonium and americium concentrations measured from the top of Rattlesnake Mountain

International Nuclear Information System (INIS)

Sehmel, G.A.

1979-01-01

Airborne plutonium-239+240 and americium-241 blowing from offsite was measured in an initial experiment at the top of Rattlesnake Mountain. Average airborne concentration measured was similar to fallout concentrations. Airborne plutonium concentrations were independent of wind speed for seven wind speed increments between 0.5 and 31 m/sec. In contrast the airborne americium concentration was a minimum at a wind speed of approximately 7 m/sec. Similarly, the airborne solids concentration in μg/m 3 was a minimum at an intermediate wind speed increment of 7 to 11 m/sec

Americium-241 radioisotope thermoelectric generator development for space applications

International Nuclear Information System (INIS)

Ambrosi, Richard; Williams, Hugo; Samara-Ratna, Piyal

2013-01-01

Space nuclear power systems are under development in the UK in collaboration with European partners as part of a European Space Agency (ESA) programme. Radioisotope thermoelectric generators (RTG) are an important element of this new capability in Europe. RTG systems being developed in Europe are targeting the 10 W electric to 50 W electric power generation range adopting a modular scalable approach to the design. Radiogenic decay heat from radioisotopes can be converted to electrical power by using appropriate semiconductor based thermoelectric materials. The plan for Europe is to develop radioisotope space nuclear power systems based on both thermoelectric and Stirling power conversion systems. Although primarily focused on delivering up to 50 W of electrical power, the European radioisotope thermoelectric system development programme is targeting americium-241 as a fuel source and is maximizing the use of commercially available thermoelectric manufacturing processes in order to accelerate the development of power conversion systems. The use of americium provides an economic solution at high isotopic purity and is product of a separation process from stored plutonium produced during the reprocessing of civil nuclear fuel. A laboratory prototype that uses electrical heating as a substitute for the radioisotope was developed to validate the designs. This prototype has now been tested. This paper outlines the requirements for a European americium-241 fuelled RTG, describes the most recent updates in system design and provides further insight into recent laboratory prototype test campaigns. (author)

Americium-241 radioisotope thermoelectric generator development for space applications

Energy Technology Data Exchange (ETDEWEB)

Ambrosi, Richard; Williams, Hugo; Samara-Ratna, Piyal, E-mail: rma8@le.ac.uk [University of Leicester, (United Kingdom); and others

2013-07-01

Space nuclear power systems are under development in the UK in collaboration with European partners as part of a European Space Agency (ESA) programme. Radioisotope thermoelectric generators (RTG) are an important element of this new capability in Europe. RTG systems being developed in Europe are targeting the 10 W electric to 50 W electric power generation range adopting a modular scalable approach to the design. Radiogenic decay heat from radioisotopes can be converted to electrical power by using appropriate semiconductor based thermoelectric materials. The plan for Europe is to develop radioisotope space nuclear power systems based on both thermoelectric and Stirling power conversion systems. Although primarily focused on delivering up to 50 W of electrical power, the European radioisotope thermoelectric system development programme is targeting americium-241 as a fuel source and is maximizing the use of commercially available thermoelectric manufacturing processes in order to accelerate the development of power conversion systems. The use of americium provides an economic solution at high isotopic purity and is product of a separation process from stored plutonium produced during the reprocessing of civil nuclear fuel. A laboratory prototype that uses electrical heating as a substitute for the radioisotope was developed to validate the designs. This prototype has now been tested. This paper outlines the requirements for a European americium-241 fuelled RTG, describes the most recent updates in system design and provides further insight into recent laboratory prototype test campaigns. (author)

Uptake and effects of americium-241 on a brackish-water amphipod

Energy Technology Data Exchange (ETDEWEB)

Hoppenheit, M.; Murray, C.N.; Woodhead, D.S.

1980-01-01

The present paper reports the results of experimental work undertaken using the brackish-water amphipod Gammarus duebeni duebeni and the transuranium nuclide americium-241. Data on the accumulation of this actinide showed that the larger fraction of the total body burden is associated with the exoskeleton. It was found that the body burden remained constant in the range pH 8.0-6.5 even though the water concentration changed markedly. It would thus appear that the concept of a concentration factor should be re-examined and it is proposed that a factor should be defined in terms of environmental and chemical parameters which represent the bioavailable fraction of the actinide. The effect of americium on survival and moulting was studied at two activity concentrations; the dose rates and absorbed doses under the experimental conditions employed have been estimated. The differences in survival rates between the control and irradiated groups were statistically analyzed and the significant difference at the higher concentration is believed to be due to a synergism between physiological stress and radiotoxicity of americium rather than the chemical toxicity of the element.

Uptake and effects of americium-241 on a brackish-water amphipod

International Nuclear Information System (INIS)

Hoppenheit, M.; Murray, C.N.; Woodhead, D.S.

1980-01-01

The present paper reports the results of experimental work undertaken using the brackish-water amphipod Gammarus duebeni duebeni and the transuranium nuclide americium-241. Data on the accumulation of this actinide showed that the larger fraction of the total body burden is associated with the exoskeleton. It was found that the body burden remained constant in the range pH 8.0-6.5 even though the water concentration changed markedly. It would thus appear that the concept of a concentration factor should be re-examined and it is proposed that a factor should be defined in terms of environmental and chemical parameters which represent the bioavailable fraction of the actinide. The effect of americium on survival and moulting was studied at two activity concentrations; the dose rates and absorbed doses under the experimental conditions employed have been estimated. The differences in survival rates between the control and irradiated groups were statistically analyzed and the significant difference at the higher concentration is believed to be due to a synergism between physiological stress and radiotoxicity of americium rather than the chemical toxicity of the element. (orig.) [de

An experimental investigation of accumulation and transmutation behavior of americium in the MOX fuel irradiated in a fast reactor

International Nuclear Information System (INIS)

Osaka, Masahiko; Koyama, Shin-ichi; Maeda, Shigetaka; Mitsugashira, Toshiaki

2005-01-01

Americium isotopes generated in the MOX fuel irradiated in the experimental fast reactor JOYO were analyzed by applying a sophisticated radiochemical technique. Americium was isolated from the irradiated MOX fuel by a combined method of anion-exchange chromatography and oxidation of Am. The isotopic ratios of americium and its content were determined by thermal ionization mass spectroscopy and α-spectrometry, respectively. The americium isotopic ratio was similar for all the specimens, but was significantly different from that of PWR-MOX. On the basis of present analytical results, the accumulation and transmutation behavior of americium nuclides in a fast reactor is discussed from the viewpoints of neutron spectrum dependence and the isomeric ratio of the 241 Am capture reaction. The estimated isomeric ratio is about 87%, which is close to the latest evaluated value. A rapid estimation method of Am content by using the 240 Pu to 239 Pu ratio was adopted and proved to be valid for the spent fuel irradiated in the fast reactor

Experimental studies to validate model calculations and maximum solubility limits for Plutonium and Americium; Experimentelle Arbeiten zur Absicherung von Modellrechnungen und Maximalkonzentrationen fuer Plutonium und Americium

Energy Technology Data Exchange (ETDEWEB)

NONE

2017-02-16

This report focuses on studies of KIT-INE to derive a significantly improved description of the chemical behaviour of Americium and Plutonium in saline NaCl, MgCl{sub 2} and CaCl{sub 2} brine systems. The studies are based on new experimental data and aim at deriving reliable Am and Pu solubility limits for the investigated systems as well as deriving comprehensive thermodynamic model descriptions. Both aspects are of high relevance in the context of potential source term estimations for Americium and Plutonium in aqueous brine systems and related scenarios. Americium and Plutonium are long-lived alpha emitting radionuclides which due to their high radiotoxicity need to be accounted for in a reliable and traceable way. The hydrolysis of trivalent actinides and the effect of highly alkaline pH conditions on the solubility of trivalent actinides in calcium chloride rich brine solutions were investigated and a thermodynamic model derived. The solubility of Plutonium in saline brine systems was studied under reducing and non-reducing conditions and is described within a new thermodynamic model. The influence of dissolved carbonate on Americium and Plutonium solubility in MgCl{sub 2} solutions was investigated and quantitative information on Am and Pu solubility limits in these systems derived. Thermodynamic constants and model parameter derived in this work are implemented in the Thermodynamic Reference Database THEREDA owned by BfS. According to the quality assurance approach in THEREDA, is was necessary to publish parts of this work in peer-reviewed scientific journals. The publications are focused on solubility experiments, spectroscopy of aquatic and solid species and thermodynamic data. (Neck et al., Pure Appl. Chem., Vol. 81, (2009), pp. 1555-1568., Altmaier et al., Radiochimica Acta, 97, (2009), pp. 187-192., Altmaier et al., Actinide Research Quarterly, No 2., (2011), pp. 29-32.).

Molecular localisation of americium, technetium and cesium in edible marine animals. Their metabolic behavior and their consequences; Localisation moleculaire de l'americium, du technetium et du cesium chez des animaux marins comestibles leur comportement metabolique et ses consequences

Energy Technology Data Exchange (ETDEWEB)

Pieri, J; Goudard, F; Milcent, M C [Laboratoire de Biochimie et Radiochimie, Faculte des Sciences et des Techniques, Nantes Cedex (France)

1992-07-01

We show the molecular behavior of americium, technetium and cesium on the chromatographic pattern of each cytosol in the digestive gland of eel and lobster. The contamination by cadmium seems to compete with americium in the fractions of MW 10,000. Cesium shows an ionic behavior. (author)

Final Radiological Assessment of External Exposure for CLEAR-Line Americium Recovery Operations

Energy Technology Data Exchange (ETDEWEB)

Davis, Adam C. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Belooussova, Olga N. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hetrick, Lucas Duane [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2014-11-12

Los Alamos National Laboratory is currently planning to implement an americium recovery program. The americium, ordinarily isotopically pure 241Am, would be extracted from existing Pu materials, converted to an oxide and shipped to support fabrication of americium oxide-beryllium neutron sources. These operations would occur in the currently proposed Chloride Extraction and Actinide Recovery (CLEAR) line of glove boxes. This glove box line would be collocated with the currently-operational Experimental Chloride Extraction Line (EXCEL). The focus of this document is to provide an in-depth assessment of the currently planned radiation protection measures and to determine whether or not further design work is required to satisfy design-goal and ALARA requirements. Further, this document presents a history of americium recovery operations in the Department of Energy and high-level descriptions of the CLEAR line operations to provide a basis of comparison. Under the working assumptions adopted by this study, it was found that the evaluated design appears to mitigate doses to a level that satisfies the ALARA-in-design requirements of 10 CFR 835 as implemented by the Los Alamos National Laboratory procedure P121. The analyses indicate that extremity doses would also meet design requirements. Dose-rate calculations were performed using the radiation transport code MCNP5 and doses were estimated using a time-motion study developed in consort with the subject matter expert. A copy of this report and all supporting documentation are located on the Radiological Engineering server at Y:\\Rad Engineering\\2013 PROJECTS\\TA-55 Clear Line.

Molecular localisation of americium, technetium and cesium in edible marine animals. Their metabolic behavior and their consequences

International Nuclear Information System (INIS)

Pieri, J.; Goudard, F.; Milcent, M.C.

1992-01-01

We show the molecular behavior of americium, technetium and cesium on the chromatographic pattern of each cytosol in the digestive gland of eel and lobster. The contamination by cadmium seems to compete with americium in the fractions of MW 10,000. Cesium shows an ionic behavior. (author)

Americium/curium bushing melter drain tests

International Nuclear Information System (INIS)

Smith, M.E.; Hardy, B.J.; Smith, M.E.

1997-01-01

Americium and curium were produced in the past at the Savannah River Site (SRS) for research, medical, and radiological applications. They have been stored in a nitric acid solution in an SRS reprocessing facility for a number of years. Vitrification of the americium/curium (Am/Cm) solution will allow the material to be safely stored or transported to the DOE Oak Ridge Reservation. Oak Ridge is responsible for marketing radionuclides for research and medical applications. The bushing melter technology being used in the Am/Cm vitrification research work is also under consideration for the stabilization of other actinides such as neptunium and plutonium. A series of melter drain tests were conducted at the Savannah River Technology Center to determine the relationship between the drain tube assembly operating variables and the resulting pour initiation times, glass flowrates, drain tube temperatures, and stop pour times. Performance criteria such as ability to start and stop pours in a controlled manner were also evaluated. The tests were also intended to provide support of oil modeling of drain tube performance predictions and thermal modeling of the drain tube and drain tube heater assembly. These drain tests were instrumental in the design of subsequent melter drain tube and drain tube heaters for the Am/Cm bushing melter, and therefore in the success of the Am/Cm vitrification and plutonium immobilization programs

Fluoride

Science.gov (United States)

Opalescence® ... Fluoride is used to prevent tooth decay. It is taken up by teeth and helps to strengthen ... and block the cavity-forming action of bacteria. Fluoride usually is prescribed for children and adults whose ...

Electric resistivity of 241-americium and 244-curium metals. Creation of defects and isochronous annealing of 241-americium metal after self-irradiation

International Nuclear Information System (INIS)

Schenkel, R.

1977-03-01

The temperature dependence of the electrical resistivity of thin films of bulk 241 Am metal were measured between 300 and 4.5 K. The room temperature resistivity was found to be 68.90μΩcm. At room temperature the electrical resistivity of americium increases with pressure (3% up to 13 kbar). The application of 13 kbar pressure did not change the low temperature power law in the electrical resistivity. The resistivity vs temperature curve can be explained by assuming s-d scattering of conduction electrons. The localized 5f electrons are considered to be about 5eV below the Fermi level. Americium therefore should be the first lanthanide-like element in the actinide series. The defect production due to self-irradiation damage was studied by measuring the increase of the resistivity at 4.2 K over a period of 738 h. A saturation resistivity of 16.036 μΩcm was found corresponding to a defect concentration of about 0.22 a/o. After isochronal annealing two recovery stages were observed at about 65 and 145 K. The two stages shift with increasing initial defect concentration to lower temperatures. Estimates of the activation energies and the reaction order were made and possible defect reactions suggested. The magnetic contribution to the electrical resistivity of curium, which shows an antiferromagnetic transition at 52.5 k, was obtained by subtracting the resistivity of americium (to be considered as phonon part). Comparison with theoretical models were made. At low temperatures the measurements are strongly affected by self-irradiation damage [drho/dt(t=0)=9.8μΩcm/h

The rapid determination of americium curium, and uranium in urine by ultrafiltration

International Nuclear Information System (INIS)

Stradling, G.N.; Popplewell, D.S.; Ham, G.J.; Griffin, R.

1975-01-01

The rapid ultrafiltration method developed for the assay of plutonium has been extended to the determination of americium, curium and uranium in urine. The limits of detection for americium and curium, and uranium are 0.09 and 0.12 dm -1 l -1 respectively, and the analysis time excluding counting less than 2 hours. The method can therefor be effectively used as a rapid screening procedure. When the reference level for plutonium is exceeded, the α activity may require to be characterised. The single ultrafiltration technique must be modified for turbid urine samples. The method is inappropriate, except for uranium, when the urine contains DTPA. (author)

Speciation and bioavailability of plutonium and americium in the Irish Sea and other marine ecosystems

International Nuclear Information System (INIS)

Vives i Batlle, J.

1993-12-01

Since the late 1960s, the Irish Sea has become a repository for a variety of radio-elements originating mainly in discharges from the British Nuclear Fuels (BNF) plc. Sellafield reprocessing complex located on the Cumbrian coast. In particular, transuranium nuclides such as plutonium, americium and curium (the main constituents of the α-emitting discharges) have become incorporated into every marine compartment by a variety of mechanisms, many of which are not well understood. Although extensive studies have been carried out in the near-field (eastern Irish Sea, especially in the vicinity of the discharge point and collateral muddy sediments), comparatively little had been done to assess the long-term behaviour and bioavailability of plutonium and americium in the far-field, e.g., the western Irish Sea, prior to the present study. In this dissertation, the results of an extensive research programme, undertaken in order to improve and refine our understanding of the behaviour of plutonium and americium in the marine environment, are presented. Specifically, the thesis details the results of (and conclusions deduced from) a series of experiments in which the physical and chemical speciation, colloidal association, mobility and bioavailability of plutonium and americium were examined in diverse environments including the Irish Sea and the Mediterranean. (author)

Structural characterisations and mechanistic investigations of the selective dissolution of americium by the ferricyanide ions in alkaline media. Application for the partitioning americium curium

International Nuclear Information System (INIS)

Fouchard, Sebastien

2000-01-01

Americium exhibits a high solubility form in basic media under oxidant conditions, unlike the other Transplutonium elements (TPE). This property can be used in the frame of High Level Liquid Waste (HLLW) treatment in order to extract preferentially the americium element, the main responsible of the long term radiotoxicity of the nuclear waste. This soluble compound can be obtained by addition of a concentrated basic solution of Fe(CN) 6 3- ions on Am(OH) 3 precipitates. This technique enables a rapid extraction of Am by the synthesis of this soluble form in alkaline solutions. Under these conditions, the other TPE remain in the solid state as trivalent hydroxide solids, strongly insoluble. In the case of dissolutions involving large amounts of Am(OH) 3 , the formation of the soluble complex is concomitant with the appearance of a reddish precipitate in the basic solution. Dissolution experiments which were carried out on this solid in NaOH/Fe(CN) 6 3- have demonstrated the dependency of the solubility equilibria with the media. Spectroscopic studies (UV Visible, XAS) on the precipitate have enabled the determination of the chemical structure and the oxidation state of the americium in the solid: Na 2 Am(V)O 2 (OH) 3 ,nH 2 O. Electrochemical studies on the americium solution have confirmed that the oxidation of Am(OH) 3 by the Fe(CN) 6 3- ions in basic media could only lead to the pentavalent form. A stoichiometric study carries out between a AmO 2 + ion and one Fe(CN) 6 3- ion and the spectroscopic characterisation of this reaction have demonstrated that the Fe(CN) 6 3- ion didn't remain as an un-complexed form in solution after the alkaline mixing. These results tend to prove that this dissolution of Am(OH) 3 is much more complex than a simple oxidation by the Fe(CN) 6 3- ions. The existence of molecular interactions between AmO 2 + and Fe(CN) 6 3- has been postulated and a mechanistic scheme has been proposed in order to explain the appearance of the soluble

Other Fluoride Products

Science.gov (United States)

... Private Wells Infant Formula Fluorosis Public Health Service Recommendation Water Operators & Engineers Water Fluoridation Additives Shortages of Fluoridation Additives Drinking Water Pipe Systems CDC-Sponsored Water Fluoridation Training Links to Other ...

The weak acid resin process: a dustless conversion route for the synthesis of americium bearing-blanket precursors

International Nuclear Information System (INIS)

Picart, S.; Gauthe, A.; Parant, P.; Remy, E.; Jobelin, I.; Pomared, J.M.; Grangaud, P.; Dauby, J.; Delahaye, T.; Caisso, M.; Bataille, M.; Bayle, J.P.; Frost, C.; Delage, C.; Martin, C.L.; Ayral, E.

2016-01-01

Mixed uranium-americium oxides are one of the materials envisaged for Americium Bearing Blankets dedicated to transmutation in fast neutron reactors. Conversion and fabrication processes are currently developed to make those materials in the form of dense and homogeneous oxide ceramic pellets or dense granulates incorporating uranium and americium. Their development points out the need of a simplified and optimized process which could lower hazards linked to dust generation of highly contaminating and irradiating compounds and facilitate material transfer in remote handling operations. This reason motivated the development of innovative 'dustless' route such as the Weak Acid Resin route (WAR) which provides the oxide precursors in the form of sub-millimeter-sized microspheres with optimal flowability and limits dust generation during conversion and fabrication steps. This study is thus devoted to the synthesis of mixed uranium-americium oxide microspheres by the WAR process and to the characterization of such precursors. This work also deals with their application to the fabrication of dense or porous pellets and with their potential use as dense spherules to make Sphere-Pac fuel. (authors)

The weak acid resin process: a dustless conversion route for the synthesis of americium bearing-blanket precursors

Energy Technology Data Exchange (ETDEWEB)

Picart, S.; Gauthe, A.; Parant, P.; Remy, E.; Jobelin, I.; Pomared, J.M.; Grangaud, P.; Dauby, J.; Delahaye, T. [CEA, Centre de Marcoule, DEN/MAR/DRCP, F-30207 Bagnols-sur-Ceze (France); Caisso, M.; Bataille, M.; Bayle, J.P. [CEA, Centre de Marcoule, DEN/MAR/DTEC, F-30207 Bagnols-sur-Ceze (France); Frost, C. [CEA, Centre de Marcoule, DEN/MAR/DRCP, F-30207 Bagnols-sur-Ceze (France); Institut Europeen des Membranes, CNRS-ENSCM-UM, CC47, University of Montpellier, F-34095 Montpellier (France); Delage, C. [CEA, Centre de Cadarache, DEN/CAD/DEC, Saint-Paul-lez-Durance (France); Martin, C.L. [Univ. Grenoble Alpes, CNRS, SIMAP, F-38000 Grenoble (France); Ayral, E. [Institut Europeen des Membranes, CNRS-ENSCM-UM, CC47, University of Montpellier, F-34095 Montpellier (France)

2016-07-01

Mixed uranium-americium oxides are one of the materials envisaged for Americium Bearing Blankets dedicated to transmutation in fast neutron reactors. Conversion and fabrication processes are currently developed to make those materials in the form of dense and homogeneous oxide ceramic pellets or dense granulates incorporating uranium and americium. Their development points out the need of a simplified and optimized process which could lower hazards linked to dust generation of highly contaminating and irradiating compounds and facilitate material transfer in remote handling operations. This reason motivated the development of innovative 'dustless' route such as the Weak Acid Resin route (WAR) which provides the oxide precursors in the form of sub-millimeter-sized microspheres with optimal flowability and limits dust generation during conversion and fabrication steps. This study is thus devoted to the synthesis of mixed uranium-americium oxide microspheres by the WAR process and to the characterization of such precursors. This work also deals with their application to the fabrication of dense or porous pellets and with their potential use as dense spherules to make Sphere-Pac fuel. (authors)

Industrial fluoride pollution: chronic fluoride poisoning in Cornwall Island cattle

Energy Technology Data Exchange (ETDEWEB)

Krook, L.; Maylin, G.A.

1979-04-01

An aluminum plant on the south bank of the St. Lawrence River, southwest of Cornwall Island, Ontario, Canada, has emitted 0.816 metric tons of fluoride daily since 1973. Considerably higher amounts were emitted from 1959 to 1973. The plant was designated as the major source of fluoride emissions impacting on Cornwall Island. Cattle located on this island showed signs of chronic fluoride poisoning. This poisoning was manifested clinically by stunted growth and dental fluorosis to a degree of severe interference with drinking and mastication. This Cornwall Island herds study indicates that the established tolerance level of fluoride for performance of dairy and beef cattle is not valid since the tolerance level was set based on experiments with healthy calves which were exposed to dietary fluoride from 3 to 4 months of age and not on cattle which were chronically exposed to fluoride from conception to death. 56 references.

Urinary fluoride excretion in preschool children after intake of fluoridated milk and use of fluoride-containing toothpaste

DEFF Research Database (Denmark)

Norman, M; Twetman, S; Hultgren Talvilahti, A

2017-01-01

Objective: To assess the urinary fluoride excretion in preschool children after drinking fluoridated milk with 0.185 mg F and 0.375 mg F and to study the impact of use of fluoride toothpaste. Basic research design: Double-blind cross-over study. Participants: Nine healthy children, 2.5-4.5 years...

Oral fluoride retention after professional topical application in children with caries activity: comparison between 1.23% fluoride foam and fluoride gel

Directory of Open Access Journals (Sweden)

Cecília Claudia Costa Ribeiro

2008-01-01

Full Text Available Objective: This study evaluated fluoride retention in the saliva of children with caries activity after topical fluoride application in the form of gel and foam. Methods: A cross-sectional, blind and randomized study, conducted with ten caries-active children aged between 8 and 10 years, in two stage, with a washout interval of two weeks between them. The treatments consisted of: a application of 2mL acidulated phosphate fluoride of the gel type in a mold and b application of 2mL acidulated phosphate fluoride of the foam type in a mold. After the washout, the treatments were inverted. Non-stimulated saliva was collected from the children at the times of 5, 15, 30 and 60 minutes after topical fluoride application. For statistical analysis the Student’s-t test was used, with a level of significance of 5%. Results: Saliva analysis was performed using a fluoride-specific electrode (ISE25F/ Radiometer, Copenhagen, Denmark at the Aquatic Science Center of the Federal University of Marana, which revealed differences after 5 minutes (p=0.0055 and 15 minutes (p=0.0208. The topical application of fluoride in the gel form revealed a higher concentration of fluoride in the saliva. Conclusion: There were differences in the retention of fluoride in the saliva of children with caries activity after the topical application of fluoride gel and the topical application of fluoride foam after 5 and 15 minutes of their application. The topical application of fluoride foam is recommended, on the basis of the lower probability of toxicity during its use.

Eukaryotic resistance to fluoride toxicity mediated by a widespread family of fluoride export proteins.

Science.gov (United States)

Li, Sanshu; Smith, Kathryn D; Davis, Jared H; Gordon, Patricia B; Breaker, Ronald R; Strobel, Scott A

2013-11-19

Fluorine is an abundant element and is toxic to organisms from bacteria to humans, but the mechanisms by which eukaryotes resist fluoride toxicity are unknown. The Escherichia coli gene crcB was recently shown to be regulated by a fluoride-responsive riboswitch, implicating it in fluoride response. There are >8,000 crcB homologs across all domains of life, indicating that it has an important role in biology. Here we demonstrate that eukaryotic homologs [renamed FEX (fluoride exporter)] function in fluoride export. FEX KOs in three eukaryotic model organisms, Neurospora crassa, Saccharomyces cerevisiae, and Candida albicans, are highly sensitized to fluoride (>200-fold) but not to other halides. Some of these KO strains are unable to grow in fluoride concentrations found in tap water. Using the radioactive isotope of fluoride, (18)F, we developed an assay to measure the intracellular fluoride concentration and show that the FEX deletion strains accumulate fluoride in excess of the external concentration, providing direct evidence of FEX function in fluoride efflux. In addition, they are more sensitive to lower pH in the presence of fluoride. These results demonstrate that eukaryotic FEX genes encode a previously unrecognized class of fluoride exporter necessary for survival in standard environmental conditions.

Higher Americium Oxidation State Research Roadmap

Energy Technology Data Exchange (ETDEWEB)

Mincher, Bruce J. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Law, Jack D. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Goff, George S. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Moyer, Bruce A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Burns, Jon D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Lumetta, Gregg J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Sinkov, Sergey I. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Shehee, Thomas C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hobbs, David T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2015-12-18

The partitioning of hexavalent Am from dissolved nuclear fuel requires the ability to efficiently oxidize Am(III) to Am(VI) and to maintain that oxidation state for a length of time sufficient to perform the separation. Several oxidants have been, or are being developed. Chemical oxidants include Ag-catalyzed ozone, Ag-catalyzed peroxydisulfate, Cu(III) periodate, and sodium bismuthate. Hexavalent americium has also now successfully been prepared by electrolysis, using functionalized electrodes. So-called auto-reduction rates of Am(VI) are sufficiently slow to allow for separations. However, for separations based on solvent extraction or ion exchange using organic resins, the high valence state must be maintained under the reducing conditions of the organic phase contact, and a holding oxidant is probably necessary. Until now, only Cu(III) periodate and sodium bismuthate oxidation have been successfully combined with solvent extraction separations. Bismuthate oxidation provided the higher DAm, since it acts as its own holding oxidant, and a successful hot test using centrifugal contactors was performed. For the other oxidants, Ag-catalyzed peroxydisulfate will not oxidize americium in nitric acid concentrations above 0.3 M, and it is not being further investigated. Peroxydisulfate in the absence of Ag catalysis is being used to prepare Am(V) in ion exchange work, discussed below. Preliminary work with Ag-catalyzed ozone has been unsuccessful for extractions of Am(VI) from 6.5 M HNO3, and only one attempt at extraction, also from 6.5 M HNO3, using the electrolytic oxidation has been attempted. However, this high acid concentration was based on the highest Am extraction efficiency using the bismuthate oxidant; which is only sparingly soluble, and thus the oxidation yield is based on bismuthate solubility. Lower acid concentrations may be sufficient with alternative oxidants and work with Ag-ozone, Cu(III) and electrolysis is on-going. Two non

No Calcium-Fluoride-Like Deposits Detected in Plaque Shortly after a Sodium Fluoride Mouthrinse

OpenAIRE

Vogel, G.L.; Tenuta, L.M.A.; Schumacher, G.E.; Chow, L.C.

2010-01-01

Plaque ‘calcium-fluoride-like’ (CaF2-like) and fluoride deposits held by biological/bacterial calcium fluoride (Ca-F) bonds appear to be the source of cariostatic concentrations of fluoride in plaque fluid. The aim of this study was to quantify the amounts of plaque fluoride held in these reservoirs after a sodium fluoride rinse. 30 and 60 min after a 228 μg/g fluoride rinse, plaque samples were collected from 11 volunteers. Each sample was homogenized, split into 2 aliquots (aliquots 1 and 2...

Urinary fluoride output in children following the use of a dual-fluoride varnish formulation

Directory of Open Access Journals (Sweden)

Kelly Polido Kaneshiro Olympio

2009-06-01

Full Text Available OBJECTIVE: This study evaluated the bioavailability of fluoride after topical application of a dual-fluoride varnish commercially available in Brazil, when compared to DuraphatTM. MATERIAL AND METHODS: The urinary fluoride output was evaluated in seven 5-year-old children after application of the fluoride varnishes, in two different phases. In the first phase (I, children received topical application of the fluoride varnish Duofluorid XII (2.92% fluorine, calcium fluoride + 2.71% fluorine, sodium fluoride, FGM TM. After 1-month interval (phase II, the same amount (0.2 mL of the fluoride varnish Duraphat (2.26% fluorine, sodium fluoride, ColgateTM was applied. Before each application all the volunteers brushed their teeth with placebo dentifrice for 7 days. Urinary collections were carried out 24 h prior up to 48 h after the applications. Fluoride intake from the diet was also estimated. Fluoride concentration in diet samples and urine was analyzed with the fluoride ion-specific electrode and a miniature calomel reference electrode coupled to a potentiometer. Data were tested by ANOVA and Tukey's post hoc test (p<0.05. RESULTS: There were significant differences in the urinary fluoride output between phases I and II. The use of Duofluorid XII did not significantly increase the urinary fluoride output, when compared to baseline levels. The application of Duraphat caused a transitory increase in the urinary fluoride output, returning to baseline levels 48 h after its use. CONCLUSIONS: The tested varnish formulation, which has been shown to be effective in in vitro studies, also can be considered safe.

Solubility of Plutonium (IV) Oxalate During Americium/Curium Pretreatment

International Nuclear Information System (INIS)

Rudisill, T.S.

1999-01-01

Approximately 15,000 L of solution containing isotopes of americium and curium (Am/Cm) will undergo stabilization by vitrification at the Savannah River Site (SRS). Prior to vitrification, an in-tank pretreatment will be used to remove metal impurities from the solution using an oxalate precipitation process. Material balance calculations for this process, based on solubility data in pure nitric acid, predict approximately 80 percent of the plutonium in the solution will be lost to waste. Due to the uncertainty associated with the plutonium losses during processing, solubility experiments were performed to measure the recovery of plutonium during pretreatment and a subsequent precipitation process to prepare a slurry feed for a batch melter. A good estimate of the plutonium content of the glass is required for planning the shipment of the vitrified Am/Cm product to Oak Ridge National Laboratory (ORNL).The plutonium solubility in the oxalate precipitation supernate during pretreatment was 10 mg/mL at 35 degrees C. In two subsequent washes with a 0.25M oxalic acid/0.5M nitric acid solution, the solubility dropped to less than 5 mg/mL. During the precipitation and washing steps, lanthanide fission products in the solution were mostly insoluble. Uranium, and alkali, alkaline earth, and transition metal impurities were soluble as expected. An elemental material balance for plutonium showed that greater than 94 percent of the plutonium was recovered in the dissolved precipitate. The recovery of the lanthanide elements was generally 94 percent or higher except for the more soluble lanthanum. The recovery of soluble metal impurities from the precipitate slurry ranged from 15 to 22 percent. Theoretically, 16 percent of the soluble oxalates should have been present in the dissolved slurry based on the dilution effects and volumes of supernate and wash solutions removed. A trace level material balance showed greater than 97 percent recovery of americium-241 (from the beta dec

Fluoride Rinses, Gels and Foams

DEFF Research Database (Denmark)

Twetman, Svante; Keller, Mette K

2016-01-01

AIM: The aim of this conference paper was to systematically review the quality of evidence and summarize the findings of clinical trials published after 2002 using fluoride mouth rinses, fluoride gels or foams for the prevention of dental caries. METHODS: Relevant papers were selected after...... (6 on fluoride mouth rinse, 10 on fluoride gel and 3 on fluoride foam); 6 had a low risk of bias while 2 had a moderate risk. All fluoride measures appeared to be beneficial in preventing crown caries and reversing root caries, but the quality of evidence was graded as low for fluoride mouth rinse......, moderate for fluoride gel and very low for acidulated fluoride foam. No conclusions could be drawn on the cost-effectiveness. CONCLUSIONS: This review, covering the recent decade, has further substantiated the evidence for a caries-preventive effect of fluoride mouth rinse, fluoride gel and foam...

The cariostatic mechanisms of fluoride

Directory of Open Access Journals (Sweden)

Kata Rošin-Grget

2013-11-01

Full Text Available This article discusses the possible cariostatic mechanisms of the action of fluoride. In the past, fluoride inhibition of caries was ascribed to reduced solubility of enamel due to incorporation of fluoride (F– into the enamel minerals. The present evidence from clinical and laboratory studies suggests that the caries-preventive mode of action of fluoride is mainly topical. There is convincing evidence that fluoride has a major effect on demineralisation and remineralisation of dental hard tissue. The source of this fluoride could either be fluorapatite (formed due to the incorporation of fluoride into enamel or calcium fluoride (CaF2-like precipitates, which are formed on the enamel and in the plaque after application of topical fluoride. Calcium fluoride deposits are protected from rapid dissolution by a phosphate –protein coating of salivary origin. At lower pH, the coating is lost and an increased dissolution rate of calcium fluoride occurs. The CaF2, therefore, act as an efficient source of free fluoride ions during the cariogenic challenge. The current evidence indicates that fluoride has a direct and indirect effect on bacterial cells, although the in vivo implications of this are still not clear. Conclusion. A better understanding of the mechanisms of the action of fluoride is very important for caries prevention and control. The effectiveness of fluoride as a cariostatic agent depends on the availability of free fluoride in plaque during cariogenic challenge, i.e. during acid production. Thus, a constant supply of low levels of fluoride in biofilm/saliva/dental interference is considered the most beneficial in preventing dental caries.

The cariostatic mechanisms of fluoride.

Science.gov (United States)

Rošin-Grget, Kata; Peroš, Kristina; Sutej, Ivana; Bašić, Krešimir

2013-11-01

This article discusses the possible cariostatic mechanisms of the action of fluoride. In the past, fluoride inhibition of caries was ascribed to reduced solubility of enamel due to incorporation of fluoride (F-) into the enamel minerals. The present evidence from clinical and laboratory studies suggests that the caries-preventive mode of action of fluoride is mainly topical. There is convincing evidence that fluoride has a major effect on demineralisation and remineralisation of dental hard tissue. The source of this fluoride could either be fluorapatite (formed due to the incorporation of fluoride into enamel) or calcium fluoride (CaF2)-like precipitates, which are formed on the enamel and in the plaque after application of topical fluoride. Calcium fluoride deposits are protected from rapid dissolution by a phosphate -protein coating of salivary origin. At lower pH, the coating is lost and an increased dissolution rate of calcium fluoride occurs. The CaF2, therefore, act as an efficient source of free fluoride ions during the cariogenic challenge. The current evidence indicates that fluoride has a direct and indirect effect on bacterial cells, although the in vivo implications of this are still not clear. A better understanding of the mechanisms of the action of fluoride is very important for caries prevention and control. The effectiveness of fluoride as a cariostatic agent depends on the availability of free fluoride in plaque during cariogenic challenge, i.e. during acid production. Thus, a constant supply of low levels of fluoride in biofilm/saliva/dental interference is considered the most beneficial in preventing dental caries. Copyright © 2013 by Academy of Sciences and Arts of Bosnia and Herzegovina.

Analysis of americium, plutonium and technetium solubility in groundwater

International Nuclear Information System (INIS)

Takeda, Seiji

1999-08-01

Safety assessments for geologic disposal of radioactive waste generally use solubilities of radioactive elements as the parameter restricting the dissolution of the elements from a waste matrix. This study evaluated americium, plutonium and technetium solubilities under a variety of geochemical conditions using the geochemical model EQ3/6. Thermodynamic data of elements used in the analysis were provided in the JAERI-data base. Chemical properties of both natural groundwater and interstitial water in buffer materials (bentonite and concrete) were investigated to determine the variations in Eh, pH and ligand concentrations (CO 3 2- , F - , PO 4 3- , SO 4 2- , NO 3 - and NH 4 + ). These properties can play an important role in the complexation of radioactive elements. Effect of the groundwater chemical properties on the solubility and formation of chemical species for americium, plutonium and technetium was predicted based on the solubility analyses under a variety of geochemical conditions. The solubility and speciation of the radioactive elements were estimated, taking into account the possible range of chemical compositions determined from the groundwater investigation. (author)

Contemporary state of plutonium and americium in the soils of Palesse state radiation-ecological reserve

International Nuclear Information System (INIS)

Papenia, M.V.; Sokolik, G.A.; Ovsiannikova, S.V.; Voinikava, E.V.; Svirschevsky, S.F.; Brown, J.; Skipperud, L.

2010-01-01

Full text: At present, the most important alpha-emitting radionuclides of Chernobyl origin are Pu 238, Pu 239, Pu 240 and Am 241. They are classified as the most dangerous group of radionuclides in view of the long half-lives and high radiotoxicity. The main part of alpha-emitted radionuclides is located within the Palesse State Radiation-Ecological Reserve. One of the most important factors determining the radioecological situation in the contaminated ecosystems is the physicochemical forms of radionuclides in a soil medium. Radionuclide species determine the radionuclide entrance into the soil solutions, their redistribution in soil profiles and the 'soil - plant' and the 'soil - surface, ground or underground water' systems as well as spreading beyond the contaminated area. The present work is devoted to investigation of state and migration ability of plutonium and americium in soils of the Palesse state radiation-ecological reserve after more than 20 years from the Chernobyl accident. The objects of investigation were mineral and organic soils sampled in 2008 with the step of 5 cm to the depth of 25-30 cm. The forms of plutonium and americium distinguishing by association with the different components of soil and by potential for migration in the soil medium were studied using the method of sequential selective extraction according to the modified Tessier scheme. Activities of Pu 238, Pu 239, Pu 240 and Am 241 in the samples were determined by the method of radiochemical analysis with alpha-spectrometer radionuclide identification. The dominant part of plutonium and americium in the soils is in immobile forms. Nowadays, radionuclide portions in water soluble and reversibly bound forms do not exceed 9.4 % of radionuclide content in the soil. In mineral soil samples, the radionuclide portions in these fractions exceed the corresponding portions in organic ones. In both mineral and organic soils, the portions of mobile americium are higher than plutonium. The

Fluoride and Oral Health.

Science.gov (United States)

O'Mullane, D M; Baez, R J; Jones, S; Lennon, M A; Petersen, P E; Rugg-Gunn, A J; Whelton, H; Whitford, G M

2016-06-01

The discovery during the first half of the 20th century of the link between natural fluoride, adjusted fluoride levels in drinking water and reduced dental caries prevalence proved to be a stimulus for worldwide on-going research into the role of fluoride in improving oral health. Epidemiological studies of fluoridation programmes have confirmed their safety and their effectiveness in controlling dental caries. Major advances in our knowledge of how fluoride impacts the caries process have led to the development, assessment of effectiveness and promotion of other fluoride vehicles including salt, milk, tablets, toothpaste, gels and varnishes. In 1993, the World Health Organization convened an Expert Committee to provide authoritative information on the role of fluorides in the promotion of oral health throughout the world (WHO TRS 846, 1994). This present publication is a revision of the original 1994 document, again using the expertise of researchers from the extensive fields of knowledge required to successfully implement complex interventions such as the use of fluorides to improve dental and oral health. Financial support for research into the development of these new fluoride strategies has come from many sources including government health departments as well as international and national grant agencies. In addition, the unique role which industry has played in the development, formulation, assessment of effectiveness and promotion of the various fluoride vehicles and strategies is noteworthy. This updated version of 'Fluoride and Oral Health' has adopted an evidence-based approach to its commentary on the different fluoride vehicles and strategies and also to its recommendations. In this regard, full account is taken of the many recent systematic reviews published in peer reviewed literature.

Contribution to the study of higher valency states of americium

International Nuclear Information System (INIS)

Langlet, Jean.

1976-01-01

Study of the chemistry of the higher valencies of americium in aqueous solutions and especially the autoreduction phenomenon. First a purification method of americium solutions is studied by precipitation, solvent extraction and ion exchange chromatography. Studies of higher valency states chemical properties are disturbed by the autoreduction phenomenon changing Am VI and Am V in Am III more stable. Stabilization of higher valency states, characterized by a steady concentration of Am VI in solution, can be done by complexation of Am VI and Am V ions or by a protecting effect of foreign ions. The original medium used has a complexing effect by SO 4 2- ions and a protecting effect by the system S 2 O 8 2- -Ag + consuming H 2 O 2 main reducing agent produced by water radiolysis. These effects are shown by the study of Am VI in acid and basic solutions. A mechanism of the stabilization effect is given [fr

Lifetime followup of the 1976 americium accident victim: [Final report

International Nuclear Information System (INIS)

Breitenstein, B.D. Jr.; Palmer, H.E.

1988-05-01

This report describes the 11 year medical course of Harold R. McCluskey, a Hanford nuclear chemical operator, who, at age 64, was involved in an accident in an americium recovery facility in August 1976. As a result of the accident, he was heavily contaminated with americium (Am-241), sustained a substantial internal deposition of this isotope, and was burned with concentrated nitric acid and injured by flying debris about the face and neck. The immediate and long-term medical care is summarized, including decontamination procedures, chelation therapy, and routine and special clinical laboratories studies. The estimates of the operator's Am-241 deposition, post accident and during the remainder of his life and the special techniques and equipment used to make the estimates, are reported. Post-accident, the total amount of Am-241 excreted in his urine and feces was 41 MBq (1.1 mCi). He died of complications of chronic coronary artery disease on August 17, 1987. 20 refs., 2 figs

Plant uptake of americium, curium, and the chemical analog neodymium

International Nuclear Information System (INIS)

Weimer, W.C.; Laul, J.C.; Kutt, J.C.; Bondietti, E.A.

1977-01-01

The plant uptake from several bulk soils has been determined for neodymium, a chemical analog to the transuranium elements americium and curium, and several other native rare earth elements as well. These investigations have demonstrated that neodymium, which has very similar chemical properties to amercium and curium and should have a similar environmental behavior, does behave indistinguishably under both laboratory and field conditions. The uptake of the weathered or mobile forms of these elements from soils is expected to be governed primarily by their identical oxidation states and nearly identical ionic radii. This hypothesis is strongly supported by the chondritic (primordial) normalized rare earth element patterns in several plants. In these samples, the entire series of rare earth elements behaves as a smooth function of the REE ionic radii, as is also seen in the contiguous soils. This behavior suggests that the plant uptake of other ions with similar chemical properties (i.e., americium and curium) would also be governed by ionic size and charge

Fluoride level in saliva after bonding orthodontic brackets with a fluoride containing adhesive

NARCIS (Netherlands)

Ogaard, B; Arends, J; Helseth, H; Dijkman, G; vanderKuijl, M

The fluoride level in saliva is considered an important parameter in caries prevention. Elevation of the salivary fluoride level by a fluoride-releasing orthodontic bonding adhesive would most likely be beneficial in the prevention of enamel caries. In this study, the fluoride level in saliva was

Ingestion Pathway Transfer Factors for Plutonium and Americium

International Nuclear Information System (INIS)

Blanchard, A.

1999-01-01

Overall transfer factors for major ingestion pathways are derived for plutonium and americium. These transfer factors relate the radionuclide concentration in a given foodstuff to deposition on the soil. Equations describing basic relationships consistent with Regulatory Guide 1.109 are followed. Updated values and coefficients from IAEA Technical Reports Series No. 364 are used when a available. Preference is given to using factors specific to the Savannah River Site

Thermodynamic systematics of oxides of americium, curium, and neighboring elements

International Nuclear Information System (INIS)

Morss, L.R.

1984-01-01

Recently-obtained calorimetric data on the sesquioxides and dioxides of americium and curium are summarized. These data are combined with other properties of the actinide elements to elucidate the stability relationships among these oxides and to predict the behavior of neighboring actinide oxides. 45 references, 4 figures, 5 tables

Fluoride release, recharge and flexural properties of polymethylmethacrylate containing fluoridated glass fillers.

Science.gov (United States)

Al-Bakri, I A; Swain, M V; Naoum, S J; Al-Omari, W M; Martin, E; Ellakwa, A

2014-06-01

The purpose of this study was to investigate the effect of fluoridated glass fillers on fluoride release, recharge and the flexural properties of modified polymethylmethacrylate (PMMA). Specimens of PMMA denture base material with various loading of fluoridated glass fillers (0%, 1%, 2.5%, 5% and 10% by weight) were prepared. Flexural properties were evaluated on rectangular specimens (n = 10) aged in deionized water after 24 hours, 1 and 3 months. Disc specimens (n = 10) were aged for 43 days in deionized water and lactic acid (pH 4.0) and fluoride release was measured at numerous intervals. After ageing, specimens were recharged and fluoride re-release was recorded at 1, 3 and 7 days after recharge. Samples containing 2.5%, 5% and 10% glass fillers showed significantly (p glass fillers specimens. All experimental specimens exhibited fluoride release in both media. The flexural strength of specimens decreased in proportion to the percentage filler inclusion with the modulus of elasticity values remaining within ISO Standard 1567. The modified PMMA with fluoridated glass fillers has the ability to release and re-release fluoride ion. Flexural strength decreased as glass filler uploading increased. © 2014 Australian Dental Association.

Fluoride glass fiber optics

CERN Document Server

Aggarwal, Ishwar D

1991-01-01

Fluoride Glass Fiber Optics reviews the fundamental aspects of fluoride glasses. This book is divided into nine chapters. Chapter 1 discusses the wide range of fluoride glasses with an emphasis on fluorozirconate-based compositions. The structure of simple fluoride systems, such as BaF2 binary glass is elaborated in Chapter 2. The third chapter covers the intrinsic transparency of fluoride glasses from the UV to the IR, with particular emphasis on the multiphonon edge and electronic edge. The next three chapters are devoted to ultra-low loss optical fibers, reviewing methods for purifying and

A simple and colorimetric fluoride receptor and its fluoride-responsive organogel

Energy Technology Data Exchange (ETDEWEB)

Yu Xudong, E-mail: 081022009@fudan.edu.cn [College of Science, Hebei University of Science and Technology, Yuhua Road 70, Shijiazhuang 050080 (China); Li Yajuan [College of Science, Hebei University of Science and Technology, Yuhua Road 70, Shijiazhuang 050080 (China); Yin Yaobing; Yu Decai [College of Science, Hebei University of Engineering, 199 South street of Guangming, Handan 056038 (China)

2012-08-01

In this paper, a new p-nitrophenylhydrozine-based anion receptor 1 containing cholesterol group had been designed and synthesized. It could selectively recognize fluoride among different anions tested with color changes from pale yellow to red for visual detection. Simultaneously, it could gel in cyclohexane, and the gel was also fluoride-responsive. When treated with TBAF (tetra-n-butylammonium fluoride), the gel could undergo gel-sol transition accompanied by color, morphology and surface changes. The binding mechanism had been investigated by UV-vis and {sup 1}HNMR (proton nuclear magnetic resonance spectra) titrations. From SEM (scanning electron microscope), SAXS (small-angle X-ray scattering), IR (Infrared Spectroscopy) and CA (contact angle) experiments, it was indicated that the addition of F{sup -} could destroy the molecule assembly of host 1 in the gel state, thus resulting in the gel-to-sol transition due to the binding site competition effect. To the best of our knowledge, this was the simplest fluoride-responsive organogel with high selectivity. Highlights: Black-Right-Pointing-Pointer A novel kind receptor for selective recognition of fluoride had been designed. Black-Right-Pointing-Pointer Its organogel was also fluoride-responsive. Black-Right-Pointing-Pointer This is the simplest fluoride-responsive organogel with high selectivity.

Fluoride metabolism in plants

Energy Technology Data Exchange (ETDEWEB)

Peters, R; Shorthouse, M

1964-04-04

Grass seedlings exposed to inorganic fluoride solutions do not take up appreciable amounts of fluoride until concentrations of more than 1.0 mM (19 p.p.m.) are used. No formation of organic fluoride has been found, even with exposure to 15.75 mM fluoride, indicating that there is no formation of fluoroacetate or similar compounds. 8 references, 2 tables.

Bottled Water and Fluoride

Science.gov (United States)

... Private Wells Infant Formula Fluorosis Public Health Service Recommendation Water Operators & Engineers Water Fluoridation Additives Shortages of Fluoridation Additives Drinking Water Pipe Systems CDC-Sponsored Water Fluoridation Training Links to Other ...

Extraction separation of americium and curium. A review

International Nuclear Information System (INIS)

Petrzilova, H.

1976-11-01

A survey is given of extraction systems suitable for transplutonium element separation and preparation as well as for the practical application of their nuclear properties. Methods are discussed in detail of separating the actinide and the lanthanide fractions from fission and corrosion products and of separating americium from curium. The description is completed with flowsheets showing the separation of transplutonium elements from irradiated targets and waste solutions after spent fuel reprocessing. (L.K.)

Transmutation of americium and curium incorporated in zirconia-based host materials

International Nuclear Information System (INIS)

Raison, P.E.

2001-01-01

Presented are studies involving the incorporation of americium and curium in zirconia-based materials. First explored was the pseudo ternary system AmO 2 -ZrO 2 -Y 2 O 3 . It was determined that selected Y-CSZ materials can incorporate significant quantities of americium oxide and remain cubic single-phase. The cell parameters of these fluorite-type products were established to be linear with the AmO 2 content. The Cm 2 O 3 -ZrO 2 system was also investigated. It was found that at 25 mol% of CmO 1.5 , the Cm(III) stabilized zirconia in its cubic form (a = 5.21 ±0.01 Angstrom). At higher and lower concentrations, diphasic materials were encountered. At 50 mol% of CmO 1.5 , a pyrochlore oxide - Cm 2 Zr 2 O 7 - is formed (a = 10.63 ±0.02 Angstrom). (author)

Fluoride release and recharge abilities of contemporary fluoride-containing restorative materials and dental adhesives.

Science.gov (United States)

Dionysopoulos, Dimitrios; Koliniotou-Koumpia, Eugenia; Helvatzoglou-Antoniades, Maria; Kotsanos, Nikolaos

2013-01-01

The aim of this study was to evaluate the fluoride release of five fluoride-releasing restorative materials and three dental adhesives, before and after NaF solution treatment. Five restorative materials (Fuji IX GP, GC Corp.; Ketac N100, 3M ESPE; Dyract Extra, Dentsply; Beautifil II, Shofu Inc.; Wave, SDI) and three dental adhesives (Stae, SDI; Fluorobond II - Shofu Inc.; Prime & Bond NT, Dentsply) were investigated before and after NaF solution treatment. A fluoride ion-selective electrode was to measure fluoride concentrations. During the 86-day period before NaF solution treatment, Fuji IX GP released the highest amount of fluoride among the restorative materials while Prime & Bond NT was the highest among the dental adhesives. After NaF solution treatment, Fuji IX GP again ranked the highest in fluoride release among the restorative materials while Fluorobond II ranked the highest among dental adhesives. It was concluded that the compositions and setting mechanisms of fluoride-containing dental materials influenced their fluoride release and recharge abilities.

No calcium-fluoride-like deposits detected in plaque shortly after a sodium fluoride mouthrinse.

Science.gov (United States)

Vogel, G L; Tenuta, L M A; Schumacher, G E; Chow, L C

2010-01-01

Plaque 'calcium-fluoride-like' (CaF(2)-like) and fluoride deposits held by biological/bacterial calcium fluoride (Ca-F) bonds appear to be the source of cariostatic concentrations of fluoride in plaque fluid. The aim of this study was to quantify the amounts of plaque fluoride held in these reservoirs after a sodium fluoride rinse. 30 and 60 min after a 228 microg/g fluoride rinse, plaque samples were collected from 11 volunteers. Each sample was homogenized, split into 2 aliquots (aliquots 1 and 2), centrifuged, and the recovered plaque fluid combined and analyzed using microelectrodes. The plaque mass from aliquot 1 was retained. The plaque mass from aliquot 2 was extracted several times with a solution having the same fluoride, calcium and pH as the plaque fluid in order to extract the plaque CaF(2)-like deposits. The total fluoride in both aliquots was then determined. In a second experiment, the extraction completeness was examined by applying the above procedure to in vitro precipitates containing known amounts of CaF(2)-like deposits. Nearly identical fluoride concentrations were found in both plaque aliquots. The extraction of the CaF(2)-like precipitates formed in vitro removed more than 80% of these deposits. The results suggest that either CaF(2)-like deposits were not formed in plaque or, if these deposits had been formed, they were rapidly lost. The inability to form persistent amounts of CaF(2)-like deposits in plaque may account for the relatively rapid loss of plaque fluid fluoride after the use of conventional fluoride dentifrices or rinses. (c) 2010 S. Karger AG, Basel.

Fluoride concentration in urine after silver diamine fluoride application on tooth enamel

Science.gov (United States)

Sari, D. L.; Bahar, A.; Gunawan, H. A.; Adiatman, M.; Rahardjo, A.; Maharani, D. A.; Toptanci, I. R.; Yavuz, I.

2017-08-01

Silver Diammine Fluoride (SDF), which contains fluoride, is known to inhibit tooth enamel demineralization and increase fluoride concentrations in saliva and urine. The aim of this study is to analyze the fluoride concentration in urine after application of SDF on tooth enamel. Urine from four subjects was collected prior to, 30 minutes after, and two and three hours after the application of SDF, and an ion-selective electrode was used to measure the fluoride concentrations. There was no significant difference between time 1 and time 2, time 1 and time 3, time 1 and time 4, time 2 and 3 (p > 0.05), and there was a significant difference between time 2 and time 4 as well as time 3 and time 4 (p < 0.05). There was a decrease in the concentration of fluoride ions in urine from the baseline to 30 minutes after application, and an increase from baseline to two and three hours after the application of SDF.

Water Fluoridation Statistics - Percent of PWS population receiving fluoridated water

Data.gov (United States)

U.S. Department of Health & Human Services — 2000-2014. Water Fluoridation Statistics is a biennial report of the percentage and number of people receiving fluoridated water from 2000 through 2014, originally...

Water Fluoridation Statistics - Percent of PWS population receiving fluoridated water

Data.gov (United States)

U.S. Department of Health & Human Services — 2000-2014 Water Fluoridation Statistics is a biennial report of the percentage and number of people receiving fluoridated water from 2000 through 2014, originally...

Fluoride releasing and enamel demineralization around orthodontic brackets by fluoride-releasing composite containing nanoparticles.

Science.gov (United States)

Melo, Mary A S; Morais, Weslanny A; Passos, Vanara F; Lima, Juliana P M; Rodrigues, Lidiany K A

2014-05-01

Fluoride-containing materials have been suggested to control enamel demineralization around orthodontic brackets during the treatment with fixed appliances. The improvement of their properties has been made through innovations, such as the application of nanotechnology by incorporation of nanofillers. This in vitro study evaluated the capacity of fluoride releasing and enamel demineralization inhibition of fluoride-releasing nanofilled cement around orthodontic brackets using an artificial caries biofilm model. Forty bovine enamel discs were selected by evaluating surface microhardness and randomized into four groups (n = 10): non-fluoride-releasing microfilled composite, fluoride-releasing microfilled composite, resin-modified glass ionomer cement (RMGI), and fluoride-releasing nanofilled composite (FN). After brackets bonding in each disc, the specimens were subjected to a cariogenic challenge through a Streptococcus mutans biofilm model. After the experimental period, the biofilm formed around the brackets was collected for fluoride analysis and the mineral loss around the brackets was determined by integrated demineralization via cross-sectional microhardness measurement at 20 and 70 μm from the bracket margin. Additionally, samples of each group were subjected to energy-dispersive X-ray spectroscopy (EDX) analysis examined under a scanning electron microscopy (SEM). ANOVA followed by Tukey test were applied for fluoride concentration and mineral loss data, respectively. At both distances, only RMGI statistically differed from the other groups presenting the lowest demineralization, although there was a trend to a lower demineralization of enamel around brackets in FN group. Similar condition was found to fluoride concentration and EDX/SEM analysis. Under the cariogenic exposure condition of this study, the fluoride-releasing nanofilled material had similar performance to fluoride-releasing microfilled materials. The presence of nanofillers in the fluoride

Oral fluoride levels 1 h after use of a sodium fluoride rinse: effect of sodium lauryl sulfate.

Science.gov (United States)

Vogel, Gerald L; Schumacher, Gary E; Chow, Laurence C; Tenuta, Livia M A

2015-01-01

Increasing the concentration of free fluoride in oral fluids is an important goal in the use of topical fluoride agents. Although sodium lauryl sulfate (SLS) is a common dentifrice ingredient, the influence of this ion on plaque fluid and salivary fluid fluoride has not been examined. The purpose of this study was to investigate the effect of SLS on these parameters and to examine the effect of this ion on total (or whole) plaque fluoride, an important source of plaque fluid fluoride after a sufficient interval following fluoride administration, and on total salivary fluoride, a parameter often used as a surrogate measure of salivary fluid fluoride. Ten subjects accumulated plaque for 48 h before rinsing with a 12 mmol/l NaF (228 µg/g F) rinse containing or not containing 0.5% (w/w) SLS. SLS had no statistically significant effect on total plaque and total saliva fluoride but significantly increased salivary fluid and plaque fluid fluoride (by 147 and 205%, respectively). These results suggest that the nonfluoride components of topical agents can be manipulated to improve the fluoride release characteristics from oral fluoride reservoirs and that statistically significant change may be observed in plaque fluid and salivary fluid fluoride concentrations that may not be observed in total plaque and total saliva fluoride concentrations.

Transmutation of americium and curium incorporated in zirconia-based host materials

Energy Technology Data Exchange (ETDEWEB)

Raison, P.E. [CEA Cadarache, 13 - Saint-Paul-lez-Durance (France). Dept. d' Etudes des Combustibles; Haire, R.G. [Oak Ridge National Lab., TN (United States)

2001-07-01

Presented are studies involving the incorporation of americium and curium in zirconia-based materials. First explored was the pseudo ternary system AmO{sub 2}-ZrO{sub 2}-Y{sub 2}O{sub 3}. It was determined that selected Y-CSZ materials can incorporate significant quantities of americium oxide and remain cubic single-phase. The cell parameters of these fluorite-type products were established to be linear with the AmO{sub 2} content. The Cm{sub 2}O{sub 3}-ZrO{sub 2} system was also investigated. It was found that at 25 mol% of CmO{sub 1.5}, the Cm(III) stabilized zirconia in its cubic form (a = 5.21 {+-}0.01 Angstrom). At higher and lower concentrations, diphasic materials were encountered. At 50 mol% of CmO{sub 1.5}, a pyrochlore oxide - Cm{sub 2}Zr{sub 2}O{sub 7} - is formed (a = 10.63 {+-}0.02 Angstrom). (author)

The cariostatic mechanisms of fluoride

OpenAIRE

Kata Rošin-Grget; Kristina Peroš; Ivana Šutej; Krešimir Bašić

2013-01-01

This article discusses the possible cariostatic mechanisms of the action of fluoride. In the past, fluoride inhibition of caries was ascribed to reduced solubility of enamel due to incorporation of fluoride (F–) into the enamel minerals. The present evidence from clinical and laboratory studies suggests that the caries-preventive mode of action of fluoride is mainly topical. There is convincing evidence that fluoride has a major effect on demineralisation and remineralisation of dental hard t...

Experimental studies to validate model calculations and maximum solubility limits for Plutonium and Americium

International Nuclear Information System (INIS)

2017-01-01

This report focuses on studies of KIT-INE to derive a significantly improved description of the chemical behaviour of Americium and Plutonium in saline NaCl, MgCl 2 and CaCl 2 brine systems. The studies are based on new experimental data and aim at deriving reliable Am and Pu solubility limits for the investigated systems as well as deriving comprehensive thermodynamic model descriptions. Both aspects are of high relevance in the context of potential source term estimations for Americium and Plutonium in aqueous brine systems and related scenarios. Americium and Plutonium are long-lived alpha emitting radionuclides which due to their high radiotoxicity need to be accounted for in a reliable and traceable way. The hydrolysis of trivalent actinides and the effect of highly alkaline pH conditions on the solubility of trivalent actinides in calcium chloride rich brine solutions were investigated and a thermodynamic model derived. The solubility of Plutonium in saline brine systems was studied under reducing and non-reducing conditions and is described within a new thermodynamic model. The influence of dissolved carbonate on Americium and Plutonium solubility in MgCl 2 solutions was investigated and quantitative information on Am and Pu solubility limits in these systems derived. Thermodynamic constants and model parameter derived in this work are implemented in the Thermodynamic Reference Database THEREDA owned by BfS. According to the quality assurance approach in THEREDA, is was necessary to publish parts of this work in peer-reviewed scientific journals. The publications are focused on solubility experiments, spectroscopy of aquatic and solid species and thermodynamic data. (Neck et al., Pure Appl. Chem., Vol. 81, (2009), pp. 1555-1568., Altmaier et al., Radiochimica Acta, 97, (2009), pp. 187-192., Altmaier et al., Actinide Research Quarterly, No 2., (2011), pp. 29-32.).

Small molecule fluoride toxicity agonists.

Science.gov (United States)

Nelson, James W; Plummer, Mark S; Blount, Kenneth F; Ames, Tyler D; Breaker, Ronald R

2015-04-23

Fluoride is a ubiquitous anion that inhibits a wide variety of metabolic processes. Here, we report the identification of a series of compounds that enhance fluoride toxicity in Escherichia coli and Streptococcus mutans. These molecules were isolated by using a high-throughput screen (HTS) for compounds that increase intracellular fluoride levels as determined via a fluoride riboswitch reporter fusion construct. A series of derivatives were synthesized to examine structure-activity relationships, leading to the identification of compounds with improved activity. Thus, we demonstrate that small molecule fluoride toxicity agonists can be identified by HTS from existing chemical libraries by exploiting a natural fluoride riboswitch. In addition, our findings suggest that some molecules might be further optimized to function as binary antibacterial agents when combined with fluoride. Copyright © 2015 Elsevier Ltd. All rights reserved.

Fluoride varnishes and enamel caries

NARCIS (Netherlands)

Bruyn, Hugo de

1987-01-01

Topical fluoride applications have the aim of increasing the fluoride uptake in enamel and consequently reducing caries. In the early ‘60s fluoride varnishes were introduced because they had a long contact period with the enamel which resulted in a higher fluoride uptake than from other topical

Daily Fluoride Intake from Iranian Green Tea: Evaluation of Various Flavorings on Fluoride Release

Directory of Open Access Journals (Sweden)

Afshin Maleki

2016-01-01

Full Text Available With increased awareness of the health benefits of the compounds in green tea, especially polyphenols, its consumption is rising. The main purpose of this study is to determine the effect of different additives on the released fluoride into tea liquor and also daily fluoride intake. The concentrations of fluoride, nitrate, sulfate, and chloride were measured in 15 different flavored green teas (Refah-Lahijan. The fluoride and other anion concentrations were measured by ion chromatography method. The data were analyzed with Statistical Package for the Social Sciences version 16.0. The results showed that the minimum and maximum concentrations of fluoride in the green tea infusions were 0.162 mg/L (cinnamon-flavored green tea and 3.29 mg/L (bagged peach-flavored green tea, respectively. The mean concentration of fluoride in the green tea leaves was 52 mg/kg, and approximately 89% of the fluoride was released from the green tea leaves into the infusions after brewing. The fluoride concentrations varied significantly among the examined green teas ( P 0.05. Finally, drinking of the studied green teas cannot make a significant contribution to the daily dietary intake of F for consumers.

Alimentary fluoride intake in preschool children

Directory of Open Access Journals (Sweden)

Lencova Erika

2011-10-01

Full Text Available Abstract Background The knowledge of background alimentary fluoride intake in preschool children is of utmost importance for introducing optimal and safe caries preventive measures for both individuals and communities. The aim of this study was to assess the daily fluoride intake analyzing duplicate samples of food and beverages. An attempt was made to calculate the daily intake of fluoride from food and swallowed toothpaste. Methods Daily alimentary fluoride intake was measured in a group of 36 children with an average age of 4.75 years and an average weight of 20.69 kg at baseline, by means of a double plate method. This was repeated after six months. Parents recorded their child's diet over 24 hours and collected duplicated portions of food and beverages received by children during this period. Pooled samples of food and beverages were weighed and solid food samples were homogenized. Fluoride was quantitatively extracted from solid food samples by a microdiffusion method using hexadecyldisiloxane and perchloric acid. The content of fluoride extracted from solid food samples, as well as fluoride in beverages, was measured potentiometrically by means of a fluoride ion selective electrode. Results Average daily fluoride intake at baseline was 0.389 (SD 0.054 mg per day. Six months later it was 0.378 (SD 0.084 mg per day which represents 0.020 (SD 0.010 and 0.018 (SD 0.008 mg of fluoride respectively calculated per kg bw/day. When adding the values of unwanted fluoride intake from the toothpaste shown in the literature (0.17-1.21 mg per day the estimate of the total daily intake of fluoride amounted to 0.554-1.594 mg/day and recalculated to the child's body weight to 0.027-0.077 mg/kg bw/day. Conclusions In the children studied, observed daily fluoride intake reached the threshold for safe fluoride intake. When adding the potential fluoride intake from swallowed toothpaste, alimentary intake reached the optimum range for daily fluoride intake

Electrodeposition of americium on a liquid cadmium cathode from a molten salt bath

International Nuclear Information System (INIS)

Laplace, A.; Lacquement, J.; Maillard, C.; Donner, L.

2004-01-01

A high-activity experiment involving the electrode position of americium on a liquid cadmium cathode from a LiCl-KCl eutectic with about 3 g of AmO 2 was conducted in a shielded cell in the ATALANTE complex. After describing the electrolyzer and the experimental conditions, the authors discuss the preparation of the LiCl-KCl-AmCl 3 solution and briefly review its electrochemical properties. It was clearly confirmed that Am(III) reduction on an inert solid cathode occurs in two steps forming Am(II) before Am(0), whereas only one reduction step was observed on liquid cadmium. The main results of this study concern americium electrode position on the liquid cadmium cathode (recovery yields, current densities, problems encountered). The solvent properties of cadmium for actinide/lanthanide separation are discussed. (authors)

Comparative evaluation of fluoride release from PRG-composites and compomer on application of topical fluoride: An in-vitro study

Directory of Open Access Journals (Sweden)

Dhull K

2009-03-01

Full Text Available Aims and Objective: To determine the fluoride release from Giomer and Compomer, using different topical fluoride regimes, and to compare the amount of fluoride release from giomer with that of compomer. Materials and Method: Forty-eight specimens of each giomer and compomer were divided into four treatment groups, namely, control group, fluoridated dentifrice (500 ppm once daily group, fluoridated dentifrice (500 ppm twice daily group, fluoridated dentifrice (500 ppm once daily + fluoridated mouthwash (225 ppm group. Each specimen was suspended in demineralizing solution for six hours and remineralizing solution for 18 hours. Fluoride release was measured in both the demineralizing solution and remineralizing solution daily for seven days. Total daily fluoride release for each specimen was calculated by adding the amount released in the demineralizing solution to that released in remineralizing solution. Results and Conclusion: The fluoride release (ppm was found to be more in Giomer when compared to Compomer. The fluoride released from Giomer and Compomer was significantly greater in the acidic demineralizing solution than in the neutral remineralizing solution. It was found that increasing fluoride exposure significantly increased fluoride release from the giomer and compomer. It was found that the fluoride release from the subgroups of giomer and compomer was in the following order: fluoridated dentifrice twice daily > fluoridated dentifrice once daily + fluoridated mouthwash > fluoridated dentifrice once daily > control group. It was found that the giomer showed a greater fluoride uptake than the compomer.

Fluoride retention by kaolin clay

DEFF Research Database (Denmark)

Kau, P. M. H.; Smith, D. W.; Binning, Philip John

1997-01-01

To evaluate the potential effectiveness of kaolin clay liners in storage of fluoride contaminated waste, an experimental study of the sorption and desorption behaviour of fluoride in kaolin clay was conducted. The degree of fluoride sorption by kaolin was found to depend on solution p......H and available fluoride concentration with equilibrium being achieved within 24 h. A site activation process involving the uptake of fluoride was also observed at the initial stages of sorption. This behaviour was attributed to a layer expansion process of the clay during sorption. The maximum fluoride sorption...... capacity was found to be 18.3 meq/100 g at pH 6 and 8.6 meq/100 g at pH 7. A competitive Langmuir sorption isotherm where sorption is dependant on both pH and fluoride concentration is employed to characterise the experimental sorption and desorption data. The sorption and desorption isotherms revealed...

Plutonium and americium extraction studies with bifunctional organophosphorus extractants

International Nuclear Information System (INIS)

Navratil, J.D.

1985-01-01

Neutral bifunctional organophosphorus extractants, such as octylphenyl-N,N-diisobutylcarbamoylmethylphosphine oxide (CMPO) and dihexyl-N,N-diethylcarbamoylmethylphosphonate (CMP), are under study at the Rocky Flats Plant (RFP) to remove plutonium and americium from the 7M nitric acid waste. These compounds extract trivalent actinides from strong nitric acid, a property which distinguishes them from monofunctional organiphosphorus reagents. Furthermore, the reagents extract hydroytic plutonium (IV) polymer which is present in the acid waste stream. The compounds extract trivalent actinides with a 3:1 stoichiometry, whereas tetra- and hexavalent actinides extract with a stoichiometry of 2:1. Preliminary studies indicate that the extracted plutonium polymer complex contains one to two molecules of CMP per plutonium ion and the plutonium(IV) maintains a polymeric structure. Recent studies by Horwitz and co-workers conclude that the CMPO and CMP reagents behave as monodentate ligands. At RFP, three techniques are being tested for using CMP and CMPO to remove plutonium and americium from nitric acid waste streams. The different techniques are liquid-liquid extraction, extraction chromatography, and solid-supported liquid membranes. Recent tests of the last two techniques will be briefly described. In all the experiments, CMP was an 84% pure material from Bray Oil Co. and CMPO was 98% pure from M and T Chemicals

Determination of plutonium, americium and curium in the marine environment

International Nuclear Information System (INIS)

Grenaut, CLaude; Germain, Pierre; Miramand, Pierre.

1982-01-01

The method used in the Laboratory for plutonium, americium and curium determination in marine samples (water, sediments, animals, plants) is presented. It is a modification of a procedure based on adsorption on ion exchange resins developed by other authors. The preliminary preparation of the samples, the radiochemical procedures and electrodeposition are described so as to be used as a practical handbook [fr

PREPARATION AND CHARACTERIZATION OF STRONTIUM FLUORIDE POWDERS ACTIVATED BY NEODYMIUM FLUORIDE

Directory of Open Access Journals (Sweden)

S. V. Kuznetsov

2015-07-01

Full Text Available Subject of Study. The paper deals with preparation processes of ultradisperse, homogeneous powder Sr1-хNdхF2+х (х= 0.003-0.2, with use of ammonium fluoride as the fluorinating agent taken over 114-120 % from stoichiometry. Method. Nitrate of strontium, neodymium nitrate hexahydrate, with the content equal to 99. 99 % of the basic substance and ammonium fluoride were used as the source of substances. Activated powders of strontium fluoride were obtained by the method of deposition from aqueous solutions by washing the precipitate with a solution of ammonium fluoride, taken over 114 - 120% from stoichiometry. The washed precipitate was centrifuged for 5-7 min, dried in the air at 30-350 C. Heat treatment of the dried precipitate was carried out in two stages: the first stage at the temperature of 200- 2500 C for 0.5-1 hour, the second one at 550- 6000 C for 2-3 hours. X-ray analysis of the synthesized samples was carried out on a Bruker D8 Advance diffractometer, radiation Cu K. The size and shape measuring of the particles of activated strontium fluoride was carried out by means of electron microscope Carl Zeiss NVision 40. The content of neodymium in activated powders of strontium fluoride was determined by the method of spectral emission analysis on the device LEA - S500. Chemical analysis for determination of ammonium ion (NH4+ content in the obtained samples was performed by the method of Kjeldahl. Calculations of lattice parameters, size of coherent scattering regions and the values of micro-deformations were carried out by TOPAS program. Main Results. Preparation processes of ultradisperse, homogeneous powder Sr1-хNdхF2+х (х= 0.003-0.2, with use of ammonium fluoride as the fluorinating agent taken over 114-120 % from stoichiometry, provides obtaining the firm solution Sr1-x-yNdx(NH4yF2+x-y of the cubic fluorite structure. It has been found out that the morphology and size of the resulting product depend on the quantity of

Fluoride analysis

Energy Technology Data Exchange (ETDEWEB)

Brandt, C S

1963-01-01

The methods and procedures for the detection and estimation of fluoride are varied and numerous. The problems of sampling, contamination, and loss in sampling waters, plant and animal tissues and atmospheres are discussed, along with brief descriptors of methods most commonly used. Techniques for separating fluorides from matrixes are discussed, as well as gravimetric, calorimetric, and spectrophotometric analytical techniques.

Story of Fluoridation

Science.gov (United States)

... Home Health Info Health Topics Fluoride Share The Story of Fluoridation It started as an observation, that ... this time using photospectrographic analysis, a more sophisticated technology than that used by McKay. Churchill asked an ...

Private Well Water and Fluoride

Science.gov (United States)

... Private Wells Infant Formula Fluorosis Public Health Service Recommendation Water Operators & Engineers Water Fluoridation Additives Shortages of Fluoridation Additives Drinking Water Pipe Systems CDC-Sponsored Water Fluoridation Training Links to Other ...

1976 Hanford americium-exposure incident: decontamination and treatment facility

International Nuclear Information System (INIS)

Berry, J.R.; McMurray, B.J.; Jech, J.J.; Breitenstein, B.D.; Quigley, E.J.

1982-01-01

An injured worker, contaminated with over 6 mCi of americium-241, required special treatment and housing for 4 months. This paper is a description of the design and management of the facility in which most of the treatment and housing occurred. The problems associated with contamination control, waste handling, supplies, and radiological concerns during the two-stage transfer of the patient from a controlled situation to his normal living environment are discussed in detail

The transmutation of americium: the Ecrix experiments in Phenix; Transmutation de l'americium: les experiences ecrix dans Phenix

Energy Technology Data Exchange (ETDEWEB)

Garnier, J C; Schmidt, N [CEA Cadarache, Dept. d' Etudes des Combustibles (DEC/SESC), 13 - Saint-Paul-lez-Durance (France); Croixmarie, Y; Ottaviani, J P [CEA Cadarache, Dept. d' Etudes des Combustibles (DEC/SPUA), 13 - Saint-Paul-lez-Durance (France); Varaine, F; Saint Jean, C de [CEA Cadarache, Dept. d' Etudes des Reacteurs (DER/SPRC), 13 - Saint-Paul-lez-Durance (France)

1999-07-01

The first americium transmutation experiment in a specific target in PHENIX will occur with the ECRIX-B and ECRIX-H experiments. Beside material testing, the objective is also to represent a concept of transmutation whose specificity is to enhance the kinetics of transmutation by using a moderated spectrum. The moderator materials will be {sup 11}B{sub 4}C and CaH{sub 2} for ECRIX-B and ECRIXH respectively, the irradiation conditions have been predicted for both the neutronics and thermal. The targets (MgO-AmO{sub X} pellets) are manufactured in the ATALANTE laboratory and the design is performed according to the PHENIX operating conditions. (authors)

Fluoride in diet

Science.gov (United States)

Diet - fluoride ... bones and teeth. Too much fluoride in the diet is very rare. Rarely, infants who get too ... of essential vitamins is to eat a balanced diet that contains a variety of foods from the ...

Uptake and recovery of americium and uranium by Anacystis biomass

International Nuclear Information System (INIS)

Liu, H.H.; Jiunntzong Wu

1993-01-01

The optimum conditions for the uptake of americium and uranium from wastewater solutions by Anacystis nidulans cells, and the recovery of these radionuclides were studied. The optimum pH range for both actinides was in the acidic region between 3.0 and 5.0. In a pH 3.5 solution with an algal biomass of 70 μg/mL, up to 95% of the Am and U were taken up by the cells. However, the uptake levels were lowered considerably when ethylene dinitrilotetraacetic acid (EDTA) or iron or calcium ions were present in the solutions. Most of the radionuclides taken up by the cells could also be desorbed by washing with salt solutions. Of nine salt solutions tested, ammonium carbonate was the most effective. Our experiments using algal biomass to remove radionuclides from wastewater showed that about 92% of americium and 85% of uranium in wastewater could be taken up by algal biomass, from which about 46% of the Am and 82% of the U originally present in the wastewater could be recovered by elution with a salt solution. 17 refs., 7 figs., 2 tabs

Picomolar traces of americium(III) introduce drastic changes in the structural chemistry of terbium(III). A break in the ''gadolinium break''

Energy Technology Data Exchange (ETDEWEB)

Welch, Jan M. [TU Wien, Atominstitut, Vienna (Austria); Mueller, Danny; Knoll, Christian; Wilkovitsch, Martin; Weinberger, Peter [TU Wien, Institute of Applied Synthetic Chemistry, Vienna (Austria); Giester, Gerald [University of Vienna, Institute of Mineralogy and Crystallography, Vienna (Austria); Ofner, Johannes; Lendl, Bernhard [TU Wien, Institute of Chemical Technologies and Analytics, Vienna (Austria); Steinhauser, Georg [Leibniz Universitaet Hannover, Institute of Radioecology and Radiation Protection (Germany)

2017-10-16

The crystallization of terbium 5,5{sup '}-azobis[1H-tetrazol-1-ide] (ZT) in the presence of trace amounts (ca. 50 Bq, ca. 1.6 pmol) of americium results in 1) the accumulation of the americium tracer in the crystalline solid and 2) a material that adopts a different crystal structure to that formed in the absence of americium. Americium-doped [Tb(Am)(H{sub 2}O){sub 7}ZT]{sub 2} ZT.10 H{sub 2}O is isostructural to light lanthanide (Ce-Gd) 5,5{sup '}-azobis[1H-tetrazol-1-ide] compounds, rather than to the heavy lanthanide (Tb-Lu) 5,5{sup '}-azobis[1H-tetrazol-1-ide] (e.g., [Tb(H{sub 2}O){sub 8}]{sub 2}ZT{sub 3}.6 H{sub 2}O) derivatives. Traces of Am seem to force the Tb compound into a structure normally preferred by the lighter lanthanides, despite a 10{sup 8}-fold Tb excess. The americium-doped material was studied by single-crystal X-ray diffraction, vibrational spectroscopy, radiochemical neutron activation analysis, and scanning electron microscopy. In addition, the inclusion properties of terbium 5,5{sup '}-azobis[1H-tetrazol-1-ide] towards americium were quantified, and a model for the crystallization process is proposed. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

A simple approach to determine the diffusivity of americium in granite

International Nuclear Information System (INIS)

Song, L.; Feng, X.; Liang, J.; Zhang, Y.; Wang, J.

2009-01-01

The diffusivities of the key radionuclides in host rock are important for the performance assessment of repositories. One of the conventional methods for determining the diffusivities of radionuclides is to grind the rock tablet layer by layer and then to measure the radioactivity remaining on the rock tablet before each grinding cycle. Since grinding hard rock samples, especially those with radioactivity, is very difficult, we developed a new approach to determine the diffusivity of americium in granite. The new approach mainly includes two parts: one is to measure the radioactivities from both sides of a rock disk sample by autoradiography with phosphor imaging technique; the other is to study the relationship between the radioactivities and the apparent diffusivity of americium in granite by computer modelling. Because the high contamination risk of grinding radioactive rock samples has been avoided, the new approach is much simpler than the conventional method. It may be a better choice of measuring the diffusivities of radionuclides in rock, especially for those laboratories in which grinding radioactive rock samples is inconvenient. (orig.)

Standard test method for quantitative determination of americium 241 in plutonium by Gamma-Ray spectrometry

CERN Document Server

American Society for Testing and Materials. Philadelphia

1994-01-01

1.1 This test method covers the quantitative determination of americium 241 by gamma-ray spectrometry in plutonium nitrate solution samples that do not contain significant amounts of radioactive fission products or other high specific activity gamma-ray emitters. 1.2 This test method can be used to determine the americium 241 in samples of plutonium metal, oxide and other solid forms, when the solid is appropriately sampled and dissolved. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Influence of dissolved organic substances in groundwater on sorption behavior of americium and neptunium

International Nuclear Information System (INIS)

Boggs, S. Jr.; Seitz, M.G.

1984-01-01

Groundwaters typically contain dissolved organic carbon consisting largely of high molecular weight compounds of humic and fulvic acids. To evaluate whether these dissolved organic substances can enhance the tranport of radionuclides through the groundwater system, experiments were conducted to examine the sorption of americium and neptunium onto crushed basalt in the presence of dissolved humic- and fulvic-acid organic carbon introduced into synthetic groundwater. The partitioning experiments with synthetic groundwater show that increasing the concentration of either humic or fulvic acid in the water has a significant inhibiting effect on sorption of both americium and neptunium. At 22 0 C, adsorption of these radionuclides, as measured by distribution ratios (the ratio of nuclide sorbed onto the solid to nuclide in solution at the end of the experiment), decreased by 25% to 50% by addition of as little as 1 mg/L dissolved organic carbon and by one to two orders of magnitude by addition of 100 to 200 mg/L dissolved organic carbon. Distribution ratios measured in solutions reacted at 90 0 C similarly decreased with the addition of dissolved organic carbon but generally ranged from one to two orders of magnitude higher than those determined in the 22 0 C experiment. These results suggest that organic carbon dissolved in deep groundwaters may significantly enhance the mobility of radionuclides of americium and neptunium. 23 references, 5 figures, 11 tables

Recovery of americium-241 from aged plutonium metal

International Nuclear Information System (INIS)

Gray, L.W.; Burney, G.A.; Reilly, T.A.; Wilson, T.W.; McKibben, J.M.

1980-01-01

After separation and purification, both actinides were precipitated as oxalates and calcined. A large-scale process was developed using dissolution, separation, purification, precipitation, and calcination. Efforts were made to control corrosion, to avoid product contamination, to keep the volume of process and waste solutions manageable, and to denitrate solutions with formic acid. The Multipurpose Processing Facility (MPPF), designed for recovery of transplutonium isotopes, was used for the first time for the precipitation and calcination of americium. Also, for the first time,, large-scale formic acid denitration was performed in a canyon vessel at SRP

Physiology and toxicity of fluoride

Directory of Open Access Journals (Sweden)

Dhar Vineet

2009-01-01

Full Text Available Fluoride has been described as an essential element needed for normal development and growth of animals and extremely useful for human beings. Fluoride is abundant in the environment and the main source of fluoride to humans is drinking water. It has been proved to be beneficial in recommended doses, and at the same time its toxicity at higher levels has also been well established. Fluoride gets accumulated in hard tissues of the body and has been know to play an important role in mineralization of bone and teeth. At high levels it has been known to cause dental and skeletal fluorosis. There are suggested effects of very high levels of fluoride on various body organs and genetic material. The purpose of this paper is to review the various aspects of fluoride and its importance in human life.

Physiology and toxicity of fluoride.

Science.gov (United States)

Dhar, Vineet; Bhatnagar, Maheep

2009-01-01

Fluoride has been described as an essential element needed for normal development and growth of animals and extremely useful for human beings. Fluoride is abundant in the environment and the main source of fluoride to humans is drinking water. It has been proved to be beneficial in recommended doses, and at the same time its toxicity at higher levels has also been well established. Fluoride gets accumulated in hard tissues of the body and has been know to play an important role in mineralization of bone and teeth. At high levels it has been known to cause dental and skeletal fluorosis. There are suggested effects of very high levels of fluoride on various body organs and genetic material. The purpose of this paper is to review the various aspects of fluoride and its importance in human life.

Fluoride barriers in Nb/Pb Josephson junctions

Science.gov (United States)

Asano, H.; Tanabe, K.; Michikami, O.; Igarashi, M.; Beasley, M. R.

1985-03-01

Josephson tunnel junctions are fabricated using a new class of artificial barriers, metal fluorides (Al fluoride and Zr fluoride). These fluoride barriers are deposited on the surface of a Nb base electrode, which are previously cleaned using a CF4 cleaning process, and covered by a Pb counterelectrode. The junctions with both Al fluoride and Zr fluoride barriers exhibit good tunneling characteristics and have low specific capacitance. In the case of Zr fluoride, it is observed that reasonable resistances are obtained even at thickness greater than 100 A. This phenomenon might be explained by tunneling via localized states in Zr fluoride.

Fluoride exposure and indicators of thyroid functioning in the Canadian population: implications for community water fluoridation.

Science.gov (United States)

Barberio, Amanda M; Hosein, F Shaun; Quiñonez, Carlos; McLaren, Lindsay

2017-10-01

There are concerns that altered thyroid functioning could be the result of ingesting too much fluoride. Community water fluoridation (CWF) is an important source of fluoride exposure. Our objectives were to examine the association between fluoride exposure and (1) diagnosis of a thyroid condition and (2) indicators of thyroid functioning among a national population-based sample of Canadians. We analysed data from Cycles 2 and 3 of the Canadian Health Measures Survey (CHMS). Logistic regression was used to assess associations between fluoride from urine and tap water samples and the diagnosis of a thyroid condition. Multinomial logistic regression was used to examine the relationship between fluoride exposure and thyroid-stimulating hormone (TSH) level (low/normal/high). Other available variables permitted additional exploratory analyses among the subset of participants for whom we could discern some fluoride exposure from drinking water and/or dental products. There was no evidence of a relationship between fluoride exposure (from urine and tap water) and the diagnosis of a thyroid condition. There was no statistically significant association between fluoride exposure and abnormal (low or high) TSH levels relative to normal TSH levels. Rerunning the models with the sample constrained to the subset of participants for whom we could discern some source(s) of fluoride exposure from drinking water and/or dental products revealed no significant associations. These analyses suggest that, at the population level, fluoride exposure is not associated with impaired thyroid functioning in a time and place where multiple sources of fluoride exposure, including CWF, exist. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

Upper limits to americium concentration in large sized sodium-cooled fast reactors loaded with metallic fuel

International Nuclear Information System (INIS)

Zhang, Youpeng; Wallenius, Janne

2014-01-01

Highlights: • The americium transmutation capability of Integral Fast Reactor was investigated. • The impact from americium introduction was parameterized by applying SERPENT Monte Carlo calculations. • Higher americium content in metallic fuel leads to a power penalty, preserving consistent safety margins. - Abstract: Transient analysis of a large sized sodium-cooled reactor loaded with metallic fuel modified by different fractions of americium have been performed. Unprotected loss-of-offsite power, unprotected loss-of-flow and unprotected transient-over-power accidents were simulated with the SAS4A/SASSYS code based on the geometrical model of an IFR with power rating of 2500 MW th , using safety parameters obtained with the SERPENT Monte Carlo code. The Ti-modified austenitic D9 steel, having higher creep rupture strength, was considered as the cladding and structural material apart from the ferritic/martensitic HT9 steel. For the reference case of U–12Pu–1Am–10Zr fuel at EOEC, the margin to fuel melt during a design basis condition UTOP is about 50 K for a maximum linear rating of 30 kW/m. In order to maintain a margin of 50 K to fuel failure, the linear power rating has to be reduced by ∼3% and 6% for 2 wt.% and 3 wt.% Am introduction into the fuel respectively. Hence, an Am concentration of 2–3 wt.% in the fuel would lead to a power penalty of 3–6%, permitting a consumption rate of 3.0–5.1 kg Am/TW h th . This consumption rate is significantly higher than the one previously obtained for oxide fuelled SFRs

Water Fluoridation: A Critical Review of the Physiological Effects of Ingested Fluoride as a Public Health Intervention

Science.gov (United States)

2014-01-01

Fluorine is the world's 13th most abundant element and constitutes 0.08% of the Earth crust. It has the highest electronegativity of all elements. Fluoride is widely distributed in the environment, occurring in the air, soils, rocks, and water. Although fluoride is used industrially in a fluorine compound, the manufacture of ceramics, pesticides, aerosol propellants, refrigerants, glassware, and Teflon cookware, it is a generally unwanted byproduct of aluminium, fertilizer, and iron ore manufacture. The medicinal use of fluorides for the prevention of dental caries began in January 1945 when community water supplies in Grand Rapids, United States, were fluoridated to a level of 1 ppm as a dental caries prevention measure. However, water fluoridation remains a controversial public health measure. This paper reviews the human health effects of fluoride. The authors conclude that available evidence suggests that fluoride has a potential to cause major adverse human health problems, while having only a modest dental caries prevention effect. As part of efforts to reduce hazardous fluoride ingestion, the practice of artificial water fluoridation should be reconsidered globally, while industrial safety measures need to be tightened in order to reduce unethical discharge of fluoride compounds into the environment. Public health approaches for global dental caries reduction that do not involve systemic ingestion of fluoride are urgently needed. PMID:24719570

Review on fluoride-releasing restorative materials--fluoride release and uptake characteristics, antibacterial activity and influence on caries formation.

Science.gov (United States)

Wiegand, Annette; Buchalla, Wolfgang; Attin, Thomas

2007-03-01

The purpose of this article was to review the fluoride release and recharge capabilities, and antibacterial properties, of fluoride-releasing dental restoratives, and discuss the current status concerning the prevention or inhibition of caries development and progression. Information from original scientific full papers or reviews listed in PubMed (search term: fluoride release AND (restorative OR glass-ionomer OR compomer OR polyacid-modified composite resin OR composite OR amalgam)), published from 1980 to 2004, was included in the review. Papers dealing with endodontic or orthodontic topics were not taken into consideration. Clinical studies concerning secondary caries development were only included when performed in split-mouth design with an observation period of at least three years. Fluoride-containing dental materials show clear differences in the fluoride release and uptake characteristics. Short- and long-term fluoride releases from restoratives are related to their matrices, setting mechanisms and fluoride content and depend on several environmental conditions. Fluoride-releasing materials may act as a fluoride reservoir and may increase the fluoride level in saliva, plaque and dental hard tissues. However, clinical studies exhibited conflicting data as to whether or not these materials significantly prevent or inhibit secondary caries and affect the growth of caries-associated bacteria compared to non-fluoridated restoratives. Fluoride release and uptake characteristics depend on the matrices, fillers and fluoride content as well as on the setting mechanisms and environmental conditions of the restoratives. Fluoride-releasing materials, predominantly glass-ionomers and compomers, did show cariostatic properties and may affect bacterial metabolism under simulated cariogenic conditions in vitro. However, it is not proven by prospective clinical studies whether the incidence of secondary caries can be significantly reduced by the fluoride release of

Silver diamine fluoride: a caries "silver-fluoride bullet".

Science.gov (United States)

Rosenblatt, A; Stamford, T C M; Niederman, R

2009-02-01

The antimicrobial use of silver compounds pivots on the 100-year-old application of silver nitrate, silver foil, and silver sutures for the prevention and treatment of ocular, surgical, and dental infections. Ag(+) kills pathogenic organisms at concentrations of linings, water purification systems, hospital gowns, and caries prevention. To distill the current best evidence relative to caries, this systematic review asked: Will silver diamine fluoride (SDF) more effectively prevent caries than fluoride varnish? A five-database search, reference review, and hand search identified 99 human clinical trials in three languages published between 1966 and 2006. Dual review for controlled clinical trials with the patient as the unit of observation, and excluding cross-sectional, animal, in vitro studies, and opinions, identified 2 studies meeting the inclusion criteria. The trials indicated that SDF's lowest prevented fractions for caries arrest and caries prevention were 96.1% and 70.3%, respectively. In contrast, fluoride varnish's highest prevented fractions for caries arrest and caries prevention were 21.3% and 55.7%, respectively. Similarly, SDF's highest numbers needed to treat for caries arrest and caries prevention were 0.8 (95% CI=0.5-1.0) and 0.9 (95% CI=0.4-1.1), respectively. For fluoride varnish, the lowest numbers needed to treat for caries arrest and prevention were 3.7 (95% CI=3.4-3.9) and 1.1 (95% CI=0.7-1.4), respectively. Adverse events were monitored, with no significant differences between control and experimental groups. These promising results suggest that SDF is more effective than fluoride varnish, and may be a valuable caries-preventive intervention. As well, the availability of a safe, effective, efficient, and equitable caries-preventive agent appears to meet the criteria of both the WHO Millennium Goals and the US Institute of Medicine's criteria for 21st century medical care.

49 CFR 173.163 - Hydrogen fluoride.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Hydrogen fluoride. 173.163 Section 173.163... Hydrogen fluoride. (a) Hydrogen fluoride (hydrofluoric acid, anhydrous) must be packaged as follows: (1) In... filling ratio of 0.84. (b) A cylinder removed from hydrogen fluoride service must be condemned in...

FLUORIDE TOXICITY – A HARSH REALITY

OpenAIRE

Bandlapalli Pavani; Mandava Ragini; David Banji; Otilia J F Banji; N Gouri Pratusha

2011-01-01

There are many incidents of fluoride toxicity whether it is acute or chronic. Fluoride toxicity is an environmental hazard which arises from the upper layers of geological crust and is dissolved in water. Prolonged drinking of such water causes chronic fluoride toxicity. Use of fluoride containing compounds for various purposes such as dental products, metal, glass, refrigerator and chemical industries act as a source of fluoride poisoning and increase the risk of toxicity. This review reflec...

Fluoride in groundwater: toxicological exposure and remedies.

Science.gov (United States)

Jha, S K; Singh, R K; Damodaran, T; Mishra, V K; Sharma, D K; Rai, Deepak

2013-01-01

Fluoride is a chemical element that is found most frequently in groundwater and has become one of the most important toxicological environmental hazards globally. The occurrence of fluoride in groundwater is due to weathering and leaching of fluoride-bearing minerals from rocks and sediments. Fluoride when ingested in small quantities (dental health by reducing dental caries, whereas higher concentrations (>1.5 mg/L) may cause fluorosis. It is estimated that about 200 million people, from among 25 nations the world over, may suffer from fluorosis and the causes have been ascribed to fluoride contamination in groundwater including India. High fluoride occurrence in groundwaters is expected from sodium bicarbonate-type water, which is calcium deficient. The alkalinity of water also helps in mobilizing fluoride from fluorite (CaF2). Fluoride exposure in humans is related to (1) fluoride concentration in drinking water, (2) duration of consumption, and (3) climate of the area. In hotter climates where water consumption is greater, exposure doses of fluoride need to be modified based on mean fluoride intake. Various cost-effective and simple procedures for water defluoridation techniques are already known, but the benefits of such techniques have not reached the rural affected population due to limitations. Therefore, there is a need to develop workable strategies to provide fluoride-safe drinking water to rural communities. The study investigated the geochemistry and occurrence of fluoride and its contamination in groundwater, human exposure, various adverse health effects, and possible remedial measures from fluoride toxicity effects.

The transmutation of americium: the Ecrix experiments in Phenix; Transmutation de l'americium: les experiences ecrix dans Phenix

Energy Technology Data Exchange (ETDEWEB)

Garnier, J.C.; Schmidt, N. [CEA Cadarache, Dept. d' Etudes des Combustibles (DEC/SESC), 13 - Saint-Paul-lez-Durance (France); Croixmarie, Y.; Ottaviani, J.P. [CEA Cadarache, Dept. d' Etudes des Combustibles (DEC/SPUA), 13 - Saint-Paul-lez-Durance (France); Varaine, F.; Saint Jean, C. de [CEA Cadarache, Dept. d' Etudes des Reacteurs (DER/SPRC), 13 - Saint-Paul-lez-Durance (France)

1999-07-01

The first americium transmutation experiment in a specific target in PHENIX will occur with the ECRIX-B and ECRIX-H experiments. Beside material testing, the objective is also to represent a concept of transmutation whose specificity is to enhance the kinetics of transmutation by using a moderated spectrum. The moderator materials will be {sup 11}B{sub 4}C and CaH{sub 2} for ECRIX-B and ECRIXH respectively, the irradiation conditions have been predicted for both the neutronics and thermal. The targets (MgO-AmO{sub X} pellets) are manufactured in the ATALANTE laboratory and the design is performed according to the PHENIX operating conditions. (authors)

Co-precipitation of plutonium(IV) and americium(III) from nitric acid-oxalic acid solutions with bismuth oxalate

International Nuclear Information System (INIS)

Pius, I.C.; Noronha, D.M.; Chaudhury, Satyajeet

2017-01-01

Co-precipitation of plutonium and americium from nitric acid-oxalic acid solutions with bismuth oxalate has been investigated for the removal of these long lived α-active nuclides from waste solutions. Effect of concentration of bismuth and oxalic acid on the co-precipitation of Pu(IV) from 3 M HNO_3 has been investigated. Similar experiments were also carried out from 3.75 M HNO_3 on co-precipitation of Am(III) to optimize the conditions of precipitation. Strong co-precipitation of Pu(IV) and Am(III) with bismuth oxalate indicate feasibility of treatment of plutonium and americium bearing waste solutions. (author)

Purification process of uranium hexafluoride containing traces of plutonium fluoride and/or neptunium fluoride

International Nuclear Information System (INIS)

Aubert, J.; Bethuel, L.; Carles, M.

1983-01-01

In this process impure uranium hexafluoride is contacted with a metallic fluoride chosen in the group containing lead fluoride PbF 2 , uranium fluorides UFsub(4+x) (0 3 at a temperature such as plutonium and/or neptunium are reduced and pure uranium hexafluoride is recovered. Application is made to uranium hexafluoride purification in spent fuel reprocessing [fr

Radiochemical separation and alpha-spectrometric determination of Americium in different matrixes

International Nuclear Information System (INIS)

Radenkovic, M.; Joksic, J.; Paligoric, D.

2009-01-01

A method of separation and alpha-spectrometric determination of americium, developed in VINCA Institute of Nuclear Sciences is described in the paper. The procedure is convenient to be used for 241 Am determination in environmental matrixes as well as samples of human origin if a very small concentrations are expected, using 243 Am as a tracer for radiochemical yield recovery. (author) [sr

Physiology and toxicity of fluoride

OpenAIRE

Dhar Vineet; Bhatnagar Maheep

2009-01-01

Fluoride has been described as an essential element needed for normal development and growth of animals and extremely useful for human beings. Fluoride is abundant in the environment and the main source of fluoride to humans is drinking water. It has been proved to be beneficial in recommended doses, and at the same time its toxicity at higher levels has also been well established. Fluoride gets accumulated in hard tissues of the body and has been know to play an important role in mineralizat...

The Effect of Calcium Pre-Rinse on Salivary Fluoride After 900 ppm Fluoride Mouthwash: A Randomized Clinical Trial

Directory of Open Access Journals (Sweden)

Nahid Ramazani

2013-01-01

Full Text Available Objective: Calcium fluoride deposit during fluoride application. Uptake and retention of fluoride by saliva depends generally on the concentration of calcium. In this study, the ef-fect of calcium pre-rinse on salivary fluoride concentration after a 900 ppm fluoride mouthwash was investigated.Materials and Methods: This cross-over double-blind randomized clinical trial was con-ducted in a girls' dormitory in Zahedan University of Medical Sciences, southeast Iran. In this study, 42 female dental students were chosen using simple randomization. During the first phase, 21 subjects (group A used fluoride rinse (F regimen and the remaining (group B used calcium pre-rinse followed immediately by fluoride rinse (Ca + F regi-men. In the second phase, participants rinsed using the mouthwashes not previously used. Prior to each phase prophylaxis was performed and no fluoridated product was used dur-ing a two-week interval between the phases. Salivary samples were taken immediately be-fore (baseline, 1 and 12 hours after rinsing. The salivary fluoride concentration was de-termined using fluoride sensitive electrode. Repeated measures ANOVA was used for sta-tistical analysis and the significance level was set at P<0.05.Results: There was significant difference between fluoride concentrations at different time points (P< 0.001. Significant differences were observed when the different time points of two regimens were examined. In contrast to this, the baseline before using F regimen and the baseline before using Ca + F regimen did not show any significance (P= 0.070.Conclusion: Pre-rinsing with calcium before fluoride is recommended because of signifi-cant increases in salivary fluoride concentration.

Fluoride resistance in Streptococcus mutans

NARCIS (Netherlands)

Liao, Ying

2017-01-01

Fluoride has been used as the most effective anti-caries agent for over five decades. It functions not only on the dental hard tissues, but also as an antimicrobial agent. It is known that oral bacteria are able to develop resistance to fluoride, which may affect the effectiveness of fluoride in

Molecular mechanisms of fluoride toxicity.

Science.gov (United States)

Barbier, Olivier; Arreola-Mendoza, Laura; Del Razo, Luz María

2010-11-05

Halfway through the twentieth century, fluoride piqued the interest of toxicologists due to its deleterious effects at high concentrations in human populations suffering from fluorosis and in in vivo experimental models. Until the 1990s, the toxicity of fluoride was largely ignored due to its "good reputation" for preventing caries via topical application and in dental toothpastes. However, in the last decade, interest in its undesirable effects has resurfaced due to the awareness that this element interacts with cellular systems even at low doses. In recent years, several investigations demonstrated that fluoride can induce oxidative stress and modulate intracellular redox homeostasis, lipid peroxidation and protein carbonyl content, as well as alter gene expression and cause apoptosis. Genes modulated by fluoride include those related to the stress response, metabolic enzymes, the cell cycle, cell-cell communications and signal transduction. The primary purpose of this review is to examine recent findings from our group and others that focus on the molecular mechanisms of the action of inorganic fluoride in several cellular processes with respect to potential physiological and toxicological implications. This review presents an overview of the current research on the molecular aspects of fluoride exposure with emphasis on biological targets and their possible mechanisms of involvement in fluoride cytotoxicity. The goal of this review is to enhance understanding of the mechanisms by which fluoride affects cells, with an emphasis on tissue-specific events in humans. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

Adsorption-Desorption Characteristics of Plutonium and Americium with Sediment Particles in the Estuarine Environment

International Nuclear Information System (INIS)

Murray, C.N.; Fukai, R.

1976-01-01

The particle formation of plutonium and americium, their adsorption onto fresh water sediments and the desorption from the sediments in sea water were studied in the Laboratory under simulated river-estuary conditions, using γ-emitting plutonium-237 and americium-241. The results of the experiments show that the particle formation of plutonium depends on its valence states, on pH and on the salinity of the medium. For river water at pH4, some 25%, 20% and 30% of the added 237 Pu was in particulate form, larger than 0.45pm, for Pu (III), Pu (IV) and Pu (VI), respectively, while 65%, 90% and 50% of the respective valence states was associated with particles at pH 8. In sea water the general pattern remains similar, although Pu (VI) is more soluble in sea water owing to higher ligand concentrations for carbonate and bicarbonate complexes. The pH-dependency of particle formation of Am (III) is more steep than that of plutonium and seems to be influenced by colloidal substances occurring in the experimental media. The adsorption-desorption characteristics of plutonium and americium with the sediment in river water as well as sea water reflect the characteristics of their particle formation, being dependent upon such properties as valence states, the pH and salinity of the medium. A sewage effluent added to the media has small but measurable effects on the adsorption-desorption processes of plutonium. (author)

Fluoride-releasing restorative materials and secondary caries.

Science.gov (United States)

Hicks, John; Garcia-Godoy, Franklin; Donly, Kevin; Flaitz, Catherine

2003-03-01

Secondary caries is responsible for 60 percent of all replacement restorations in the typical dental practice. Risk factors for secondary caries are similar to those for primary caries development. Unfortunately, it is not possible to accurately predict which patients are at risk for restoration failure. During the past several decades, fluoride-releasing dental materials have become a part of the dentist's armamentarium. Considerable fluoride is released during the setting reaction and for periods up to eight years following restoration placement. This released fluoride is readily taken up by the cavosurface tooth structure, as well as the enamel and root surfaces adjacent to the restoration. Resistance against caries along the cavosurface and the adjacent smooth surface has been shown in both in vitro and in vivo studies. Fluoride-releasing dental materials provide for improved resistance against primary and secondary caries in coronal and root surfaces. Plaque and salivary fluoride levels are elevated to a level that facilitates remineralization. In addition, the fluoride released to dental plaque adversely affects the growth of lactobacilli and mutans streptococci by interference with bacterial enzyme systems. Fluoride recharging of these dental materials is readily achieved with fluoridated toothpastes, fluoride mouthrinses, and other sources of topical fluoride. This allows fluoride-releasing dental materials to act as intraoral fluoride reservoirs. The improvement in the properties of dental materials with the ability to release fluoride has improved dramatically in the past decade, and it is anticipated that in the near future the vast majority of restorative procedures will employ fluoride-releasing dental materials as bonding agents, cavity liners, luting agents, adhesives for orthodontic brackets, and definitive restoratives.

Americium-241: the most useful isotope of the actinide elements

International Nuclear Information System (INIS)

Navratil, J.D.

1984-01-01

Used extensively in nuclear gauges and in many other areas, this man-made element (Atomic Number 95) was first isolated in weighable amounts during World War II. Americium is now a very useful by-product of the nuclear industry and is produced in kilogram amounts by appropriate recovery, separation and purification processes. A review will be presented of its discovery, nuclear and chemical properties, and uses, with emphasis on its production process and separations chemistry

Study of the extraction and the purification of americium and trivalent actinides contained in effluents with supported liquid membranes

International Nuclear Information System (INIS)

Guillou, P.

1990-12-01

The supported liquid membrane technique is studied and developed for americium recovery from uranium or plutonium matrices and decontamination of liquid radioactive wastes. First tests on uranium-nickel solutions with a flat membrane showed the easiness of the operation and the efficiency of the process. Acid-resistant (10 N), interchangeable elements with hollow fibers, are developed and also a computerized automatic device. The different tests on americium solutions demonstrate the feasibility and the reliability of the system. Influence of various parameters on transfer kinetics is investigated

Physics of plutonium and americium recycling in PWR using advanced fuel concepts

International Nuclear Information System (INIS)

Hourcade, E.

2004-01-01

PWR waste inventory management is considered in many countries including Frances as one of the main current issues. Pu and Am are the 2 main contents both in term of volume and long term radio-toxicity. Waiting for the Generation IV systems implementation (2035-2050), one of the mid-term solutions for their transmutation involves the use of advanced fuels in Pressurized Water Reactors (PWR). These have to require as little modification as possible of the core internals, the cooling system and fuel cycle facilities (fabrication and reprocessing). The first part of this paper deals with some neutronic characteristics of Pu and/or Am recycling. In a second part, 2 technical solutions MOX-HMR and APA-DUPLEX-84 are presented and the third part is devoted to the study of a few global strategies. The main neutronic parameters to be considered for Pu and Am recycling in PWR are void coefficient, Doppler coefficient, fraction of delayed neutrons and power distribution (especially for heterogeneous configurations). The modification of the moderation ratio, the opportunity to use inert matrices (targets), the optimisation of Uranium, Plutonium and Americium contents are the key parameters to play with. One of the solutions (APA-DUPLEX-84) presented here is a heterogeneous assembly with regular moderation ratio composed with both target fuel rods (Pu and Am embedded in an inert matrix) and standard UO 2 fuel rods. An EPR (European Pressurised Reactor) type reactor, loaded only with assemblies containing 84 peripheral targets, can reach an Americium consumption rate of (4.4; 23 kg/TWh) depending on the assembly concept. For Pu and Am inventories stabilisation, the theoretical fraction of reactors loaded with Pu + Am or Pu assemblies is about 60%. For Americium inventory stabilisation, the fraction decreases down to 16%, but Pu is produced at a rate of 18.5 Kg/TWh (-25% compared to one through UOX cycle)

Fluoride uptake into the developing enamel and dentine of sheep incisors following daily ingestion of fluoridated milk or water

International Nuclear Information System (INIS)

Cuttress, T.W.; Suckling, G.W.; Gao, J.; Coote, G.E.

1996-01-01

The caries preventive action of fluoride is common knowledge, although some of the mechanisms involved remain equivocal. At present, raised local levels of fluoride at, or in, the surface of tooth enamel is the most commonly accepted explanation of the anti-cariogenic action of fluoride. However, fluoride incorporated as fluorapatite into the tooth during its formation remains a possible alternative or complementary anti-cariogenic mechanism. If so, regular ingestion of fluoride during tooth formation is beneficial. Although use of fluoridated water is the preferred method in public health programmes, access to suitable potable water is required, and often this in not feasible. Fresh, preserved, or dried cow's milk products are widely used as nutritional and dietary items in most populations, particularly for young children. Milk is a practical, controllable means for regular delivery of fluoride. Processing of milk is commonly centralised and uses standardised conditions, allowing easy supplementation of fluoride for distribution to communities. The purpose of this study was to resolve the question of availability of fluoride ingested in milk compared with fluoride ingested in water by measuring fluoride deposition in the developing permanent incisors of young sheep. Incisors were analysed using a proton microprobe. (author). 18 refs., 1 tabs., 3 figs

Influence of the method of fluoride administration on toxicity and fluoride concentrations in Japanese quail

Science.gov (United States)

Fleming, W.J.; Schuler, C.A.

1988-01-01

Young Japanese quail (Coturnix japonica) were administered NaF for 16 d either in their diet or by esophageal intubation. Based on the total fluoride ion (Emg F-) intake over the l6-d experimental period, fluoride administered by intubation was at least six times more toxic than that fed in the diet. Dietary concentrations of 1,000 ppm F- (Emg F- for 16 d = approx. 144) produced no mortality, whereas intubated doses produced 73% or greater mortality in all groups administered 54 mg F- /kg/d or more (Emg F- for 16 d _ approx. 23 mg). GraphIc companson of the regression of log F- ppm in femurs/mg F- intake showed that fluoride levels in the femurs of quail administered fluoride by intubation were higher than in those administered fluoride in the diet.

Transfer of environmental plutonium and americium across the human gut

International Nuclear Information System (INIS)

Hunt, G.J.; Leonard, D.R.P.; Lovett, M.B.

1989-01-01

Following the ingestion of winkles obtained from a coastal area near Sellafield nuclear reprocessing plant, a group of volunteers provided urine for the next 7 days to be analysed for plutonium and americium. From this, estimates of the intake and gut transfer factors for these isotopes were determined. Preliminary estimates of gut transfer factors from a previous study by the same authors were then re-interpreted and combined with the results from the present study. (UK)

Application of Titanium Compounds to Reduce Fluoride Ion in Water Resources with High Fluoride Ion Contents

Directory of Open Access Journals (Sweden)

Fariborz Riahi

2005-06-01

Full Text Available The present work describes studies on the sorption of fluoride ions from water by titanium compounds used in water treatment to reduce fluoride content in water resources. There are different methods of reducing fluoride ion in water, each associated with specific problems such as secondary contamination, environmental contamination, high costs, or the need for primary and secondary treatment. In this study, application of titanium sulfate and Metatitanic acid produced from titanium ore concentrate (ileminite is investigated in the removal of fluoride ion and the possibility of complete purification of fluorine containing wastewater is examined to determine the optimal conditions. Metatitanic acid has a great sorption property for fluoride ion. Also titanium sulfate is a suitable and more effective material for this purpose. Efficiency of this material in reducing fluoride ion content is 99.9% and it is possible to refresh sorbet material for reuse without problems arising from Ti+4 ion contamination.

Total and Compound Formation Cross Sections for Americium Nuclei: Recommendations for Coupled-Channels Calculations

Energy Technology Data Exchange (ETDEWEB)

Escher, J. E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-04-11

Calculations for total cross sections and compound-nucleus (CN) formation cross sections for americium isotopes are described, for use in the 2017 NA-22 evaluation effort. The code ECIS 2006 was used in conjunction with Frank Dietrich's wrapper `runtemplate'.

Toxic effects of fluoride on organisms.

Science.gov (United States)

Zuo, Huan; Chen, Liang; Kong, Ming; Qiu, Lipeng; Lü, Peng; Wu, Peng; Yang, Yanhua; Chen, Keping

2018-04-01

Accumulation of excess fluoride in the environment poses serious health risks to plants, animals, and humans. This endangers human health, affects organism growth and development, and negatively impacts the food chain, thereby affecting ecological balance. In recent years, numerous studies focused on the molecular mechanisms associated with fluoride toxicity. These studies have demonstrated that fluoride can induce oxidative stress, regulate intracellular redox homeostasis, and lead to mitochondrial damage, endoplasmic reticulum stress and alter gene expression. This paper reviews the present research on the potential adverse effects of overdose fluoride on various organisms and aims to improve our understanding of fluoride toxicity. Copyright © 2018 Elsevier Inc. All rights reserved.

Magnetic interactions through fluoride

DEFF Research Database (Denmark)

Pedersen, Kasper Steen; Sigrist, Marc; Weihe, Høgni

2014-01-01

support the parameter values and resolve |E| ≈ 0.04 cm(-1). The exchange coupling constant (J) is 1 order of magnitude smaller than that found in comparable systems with linear oxide bridging but comparable to typical magnitudes through cyanide, thus underlining the potential of fluoride complexes......The nature of the magnetic interaction through fluoride in a simple, dinuclear manganese(III) complex (1), bridged by a single fluoride ion in a perfectly linear fashion, is established by experiment and density functional theory. The magnitude of the antiferromagnetic exchange interaction...

Mycoremediation. The study of transfer factor for plutonium and americium uptake from the ground

International Nuclear Information System (INIS)

Dusan Galanda; Lubomir Matel; Jana Strisovska; Silvia Dulanska

2014-01-01

In our scientific research we have monitored mycoremediation's properties of oyster mushrooms in cultivation on the soil what is contaminated by solutions with radioactive isotopes of 239 Pu and 241 Am with known activity. We monitored specific activities of absorbed radionuclides in fruiting bodies and chemical forms of radionuclides which were compared to calculated specific activities of two background samples of oyster mushrooms intended for consumer purpose. We determined distributive coefficients between the ground and the fruiting body of oyster mushrooms. The average value which was obtained for the transfer factor for plutonium was 0.72 and for americium 3.97. To evaluate a quantity of absorbed radionuclides we used a method of liquid extraction. The emitting alpha radiation of alpha radionuclides was detected by spectrometry. For defining individual fractions of plutonium and americium that are contained in mushroom bodies was used the sequential leaching method. (author)

High-purity germanium detection system for the in vivo measurement of americium and plutonium

International Nuclear Information System (INIS)

Tyree, W.H.; Falk, R.B.; Wood, C.B.; Liskey, R.W.

1976-01-01

A high-purity germanium (HPGe) array, photon-counting system has been developed for the Rocky Flats Plant Body-Counter Medical Facility. The newly improved system provides exceptional resolutions of low-energy X-ray and gamma-ray spectra associated with the in vivo deposition of plutonium and americium. Described are the operational parameters of the system and some qualitative results illustrating detector performance for the photon emissions produced from the decay of plutonium and americium between energy ranges from 10 to 100 kiloelectron volts. Since large amounts of data are easily generated with the system, data storage, analysis, and computer software developments continue to be an essential ingredient for processing spectral data obtained from the detectors. Absence of quantitative data is intentional. The primary concern of the study was to evaluate the effects of the various physical and electronic operational parameters before adding those related entirely to a human subject

[The effect of fluoride-containing tooth paste on dental plaque and on fluoride level in the mouth].

Science.gov (United States)

Oomori, H

1989-01-01

Various kinds of fluoride have been used for a long time and there are many reports concerning fluorides and their effects. Recently, the caries-inhibiting action of fluoride-containing tooth paste has been given much attention. In this study, I tried to clarify the residual time and amount of fluoride derived from the fluoride-containing tooth paste in the mouth, as well as to assess possible variation in bacterial composition in the dental plaque bacteriologically and biochemically. In the study on the fluoride clearance from the mouth, both 1.0 g and 0.5 g of paste showed the same reduction rates; and about an 80% reduction was recognized between the value at 3 minutes and that at 30 minutes, and about a 40% reduction from the 30-minute to the 60-minute interval. Next, a study on the variation in plaque bacteria was carried out. The total number of the CFU on each plate was not different between samples obtained before and after the use of the tooth paste; moreover, no difference was noted between aerobic and anaerobic culture. However, when plaque before and after brushing with fluoride-containing tooth paste were cultured in 10% sucrose solution, the differences of acid production such as lactic acid, acetic acid, and formic acid were demonstrated. Namely, these acid productions were inhibited after the use of fluoride, especially lactic acid was strongly inhibited. On the other hand, when Str. mutans from the plaque obtained after the use of fluoride-containing tooth paste was cultured in fluoride-free BHI broth, the inhibition of acid from carbohydrates was not shown clearly.(ABSTRACT TRUNCATED AT 250 WORDS)

Physiologic Conditions Affect Toxicity of Ingested Industrial Fluoride

Directory of Open Access Journals (Sweden)

Richard Sauerheber

2013-01-01

Full Text Available The effects of calcium ion and broad pH ranges on free fluoride ion aqueous concentrations were measured directly and computed theoretically. Solubility calculations indicate that blood fluoride concentrations that occur in lethal poisonings would decrease calcium below prevailing levels. Acute lethal poisoning and also many of the chronic effects of fluoride involve alterations in the chemical activity of calcium by the fluoride ion. Natural calcium fluoride with low solubility and toxicity from ingestion is distinct from fully soluble toxic industrial fluorides. The toxicity of fluoride is determined by environmental conditions and the positive cations present. At a pH typical of gastric juice, fluoride is largely protonated as hydrofluoric acid HF. Industrial fluoride ingested from treated water enters saliva at levels too low to affect dental caries. Blood levels during lifelong consumption can harm heart, bone, brain, and even developing teeth enamel. The widespread policy known as water fluoridation is discussed in light of these findings.

Physiologic conditions affect toxicity of ingested industrial fluoride.

Science.gov (United States)

Sauerheber, Richard

2013-01-01

The effects of calcium ion and broad pH ranges on free fluoride ion aqueous concentrations were measured directly and computed theoretically. Solubility calculations indicate that blood fluoride concentrations that occur in lethal poisonings would decrease calcium below prevailing levels. Acute lethal poisoning and also many of the chronic effects of fluoride involve alterations in the chemical activity of calcium by the fluoride ion. Natural calcium fluoride with low solubility and toxicity from ingestion is distinct from fully soluble toxic industrial fluorides. The toxicity of fluoride is determined by environmental conditions and the positive cations present. At a pH typical of gastric juice, fluoride is largely protonated as hydrofluoric acid HF. Industrial fluoride ingested from treated water enters saliva at levels too low to affect dental caries. Blood levels during lifelong consumption can harm heart, bone, brain, and even developing teeth enamel. The widespread policy known as water fluoridation is discussed in light of these findings.

Potential fluoride toxicity from oral medicaments: A review.

Science.gov (United States)

Ullah, Rizwan; Zafar, Muhammad Sohail; Shahani, Nazish

2017-08-01

The beneficial effects of fluoride on human oral health are well studied. There are numerous studies demonstrating that a small amount of fluoride delivered to the oral cavity decreases the prevalence of dental decay and results in stronger teeth and bones. However, ingestion of fluoride more than the recommended limit leads to toxicity and adverse effects. In order to update our understanding of fluoride and its potential toxicity, we have described the mechanisms of fluoride metabolism, toxic effects, and management of fluoride toxicity. The main aim of this review is to highlight the potential adverse effects of fluoride overdose and poorly understood toxicity. In addition, the related clinical significance of fluoride overdose and toxicity has been discussed.

Effects of hydrogen fluoride on plants

Energy Technology Data Exchange (ETDEWEB)

Yamazoe, F

1970-07-15

Symptoms of fluorosis in plants are chlorotic markings around the tip or edges of young leaves. Examples of damage to plants and livestock by fluorides are listed, including the retarded growth of silkworms fed on mulberry leaves polluted by more than 30 ppm fluorides. Plants can be classified into six groups according to their resistance to hydrogen fluoride. Threshold values of the fluoride concentration range from 5-10 ppb for the plants. Gladiolus is normally employed as a plant indicator for hydrogen fluoride and silkworms as indicator insects. The relationship between plant damage by fluorides and exposure time, density, soil, fertilizer, meteorology and location are examined. Several preventive measures are listed, including the spraying of water or lime on plant leaves. It is concluded that the establishment of an environmental standard is difficult because of the extremely high sensitivity of the plants to the gas. 8 references.

Effect of 241-americium on bone marrow stroma

International Nuclear Information System (INIS)

Heuvel, R. van den

1990-01-01

The regulation of haemopoiesis occurs via complex interactions between the stroma and the haemopoietic cells. An attempt to further clarifying the mechanisms and the exact role of the stroma in the regulation was made in a study. Results revealed that the murine bone marrow stromal cells are highly radiosensitive after injection with 241-americium and can thus be considered as a target population after internal contamination. In addition, observations are made which may be important for risk estimation for the developing animal and during pregnancy. Contamination in utero and by lactation shows persistent damage up to 1 year after contamination at an average annual dose of 5 cGy. (author)

The extraction of lanthanides and americium by benzyldiakylamines and benzyltrialkylammonium nitrates from the nitrate solutions; structure and aggregation of their salts

International Nuclear Information System (INIS)

Jedinakova, V.; Zilkova, J.; Dvorak, Z.; Vojtiskova, M.

1982-01-01

Benzyldialkylamine and benzyltrialkylammonium nitrates were used for the extraction of lanthanides and americium from aqueous nitrate solutions. The dependence of the extraction performance for Ln(III) and Am(III) on the concentration of nitric acid, the kind and concentration of salting-out agents in the aqueous phase, and the kind of solvent were investigated. The extraction of Am(III) is compared with the extraction of lanthanides. The difference in distribution coefficients for lanthanides and americium can be utilized for the separation of lanthanides and americium. Using vapor phase osmometry and cryoscopy the association of these compounds was measured at 5.5deg, 25deg and 37deg C, allowing rough estimates of ΔH and ΔS for the formation of the aggregates, monomers in the case of benzyldiethylamine, benzyldibutylamine, benzyldihexylamine and benzyldioctylamine, tetramers for the benzyldibutylamine nitrate and tetramers for benzyldimethyldodecylammonium nitrate. (author)

Pretreatment of americium/curium solutions for vitrification

International Nuclear Information System (INIS)

Rudisill, T.S.

1996-01-01

Vitrification will be used to stabilize an americium/curium (Am/Cm) solution presently stored in F-Canyon for eventual transport to the heavy isotope programs at Oak Ridge National Laboratory. Prior to vitrification, an in-tank oxalate precipitation and a series of oxalic/nitric acid washes will be used to separate these elements and lanthanide fission products from the bulk of the uranium and metal impurities present in the solution. Pretreatment development experiments were performed to understand the behavior of the lanthanides and the metal impurities during the oxalate precipitation and properties of the precipitate slurry. The results of these experiments will be used to refine the target glass composition allowing optimization of the primary processing parameters and design of the solution transfer equipment

Sirt1 overexpression suppresses fluoride-induced p53 acetylation to alleviate fluoride toxicity in ameloblasts responsible for enamel formation.

Science.gov (United States)

Suzuki, Maiko; Ikeda, Atsushi; Bartlett, John D

2018-03-01

Low-dose fluoride is an effective caries prophylactic, but high-dose fluoride is an environmental health hazard that causes skeletal and dental fluorosis. Treatments to prevent fluorosis and the molecular pathways responsive to fluoride exposure remain to be elucidated. Previously we showed that fluoride activates SIRT1 as an adaptive response to protect cells. Here, we demonstrate that fluoride induced p53 acetylation (Ac-p53) [Lys379], which is a SIRT1 deacetylation target, in ameloblast-derived LS8 cells in vitro and in enamel organ in vivo. Here we assessed SIRT1 function on fluoride-induced Ac-p53 formation using CRISPR/Cas9-mediated Sirt1 knockout (LS8 Sirt/KO ) cells or CRISPR/dCas9/SAM-mediated Sirt1 overexpressing (LS8 Sirt1/over ) cells. NaF (5 mM) induced Ac-p53 formation and increased cell cycle arrest via Cdkn1a/p21 expression in Wild-type (WT) cells. However, fluoride-induced Ac-p53 was suppressed by the SIRT1 activator resveratrol (50 µM). Without fluoride, Ac-p53 persisted in LS8 Sirt/KO cells, whereas it decreased in LS8 Sirt1/over . Fluoride-induced Ac-p53 formation was also suppressed in LS8 Sirt1/over cells. Compared to WT cells, fluoride-induced Cdkn1a/p21 expression was elevated in LS8 Sirt/KO and these cells were more susceptible to fluoride-induced growth inhibition. In contrast, LS8 Sirt1/over cells were significantly more resistant. In addition, fluoride-induced cytochrome-c release and caspase-3 activation were suppressed in LS8 Sirt1/over cells. Fluoride induced expression of the DNA double strand break marker γH2AX in WT cells and this was augmented in LS8 Sirt1/KO cells, but was attenuated in LS8 Sirt1/over cells. Our results suggest that SIRT1 deacetylates Ac-p53 to mitigate fluoride-induced cell growth inhibition, mitochondrial damage, DNA damage and apoptosis. This is the first report implicating Ac-p53 in fluoride toxicity.

Eukaryotic resistance to fluoride toxicity mediated by a widespread family of fluoride export proteins

OpenAIRE

Li, Sanshu; Smith, Kathryn D.; Davis, Jared H.; Gordon, Patricia B.; Breaker, Ronald R.; Strobel, Scott A.

2013-01-01

Although fluoride is plentiful in the environment and is commonly used at high concentrations in oral hygiene products, little has been known about how biological systems overcome the toxic effects of this anion. We demonstrate that a protein called FEX in many fungi is essential for cell survival in the presence of high fluoride concentrations. The protein is required for the rapid expulsion of cytoplasmic fluoride, indicating that many eukaryotic species that carry FEX genes likely avoid fl...

Gramicidin D enhances the antibacterial activity of fluoride

OpenAIRE

Nelson, James W.; Zhou, Zhiyuan; Breaker, Ronald R.

2014-01-01

Fluoride is a toxic anion found in many natural environments. One of the major bacterial defenses against fluoride is the cell envelope, which limits passage of the membrane-impermeant fluoride anion. Accordingly, compounds that enhance the permeability of bacterial membranes to fluoride should also enhance fluoride toxicity. In this study, we demonstrate that the pore-forming antibiotic gramicidin D increases fluoride uptake in B. subtilis and that the antibacterial activity of this compound...

Accumulation of fluoride by plants and vegetables

International Nuclear Information System (INIS)

Njenga, L.W.; Kariuki, D.N.

1994-01-01

Fluoride in plant and vegetable samples has been determined using ion selective electrode. The analysis was carried out after ashing the sample on an open flame, adding perchloric acid and allowing the hydrogen fluoride to diffuse into sodium hydroxide layer.The results obtained show that kale and pumpkins can accumulate more than ten times their normal values of fluoride while plants were found to accumulate upto 100μg/g fluoride when exposed to highlevels of fluoride in water or soil. (author)

Spatial distribution mapping of drinking water fluoride levels in Karnataka, India: fluoride-related health effects.

Science.gov (United States)

Chowdhury, Chitta R; Shahnawaz, Khijmatgar; Kumari, Divya; Chowdhury, Avidyuti; Bedi, Raman; Lynch, Edward; Harding, Stewart; Grootveld, Martin

2016-11-01

(1) To estimate the concentrations of fluoride in drinking water throughout different zones and districts of the state of Karnataka. (2) To investigate the variation of fluoride concentration in drinking water from different sources, and its relationships to daily temperature and rainfall status in the regional districts. (3) To develop an updated fluoride concentration intensity map of the state of Karnataka, and to evaluate these data in the context of fluoride-related health effects such as fluorosis and their prevalence. Aqueous standard solutions of 10, 100 and 1,000 ppm fluoride (F - ) were prepared with analytical grade Na + /F - and a buffer; TISAB II was incorporated in both calibration standard and analysis solutions in order to remove the potentially interfering effects of trace metal ions. This analysis was performed using an ion-selective electrode (ISE), and mean determination readings for n = 5 samples collected at each Karnataka water source were recorded. The F - concentration in drinking water in Karnataka state was found to vary substantially, with the highest mean values recorded being in the north-eastern zone (1.61 ppm), and the lowest in the south-western one (only 0.41 ppm). Analysis of variance (ANOVA) demonstrated that there were very highly significant 'between-zone' and 'between-districts-within-zones' sources of variation (p water source F - levels within this state. The southern part of Karnataka has low levels of F - in its drinking water, and may require fluoridation treatment in order to mitigate for dental caries and further ailments related to fluoride deficiency. However, districts within the north-eastern region have contrastingly high levels of fluoride, an observation which has been linked to dental and skeletal fluorosis. This highlights a major requirement for interventional actions in order to ensure maintenance of the recommended range of fluoride concentrations (0.8-1.5 ppm) in Karnataka's drinking water

Consideration of the effect of lymph-node deposition upon the measurement of plutonium and americium in the lungs

International Nuclear Information System (INIS)

Falk, R.B.; Lagerquist, C.R.

1975-01-01

Measurement of an inhaled radionuclide by external photon counting includes quantities which may be contained in lymph nodes, as well as quantities in the lungs. An overestimate of the lung burden can result, if a portion of the radionuclide were present in the lymph nodes. This problem is analyzed with respect to the measurement of inhaled plutonium containing plutonium-241 and americium-241, when americium-241 has been used as a tracer for the plutonium. Equations are derived which yield the amounts of americium and of plutonium in the lungs and in the lymph nodes as a function of time after exposure and for various translocation and retention parameters. Count histories (count profiles) of actual exposure cases are compared with calculated count profiles in order to gain insight into possible values of the translocation and retention parameters. Comparison is also made with calculated count profiles using values of translocation and retention parameters recommended by the International Commission on Radiological Protection (ICRP) for use with the Task Group Lung Model. The magnitude of the possible overestimate (error factor) was calculated for combinations o []parameters which yielded matches to the observed count histories. (auth)

Gramicidin D enhances the antibacterial activity of fluoride.

Science.gov (United States)

Nelson, James W; Zhou, Zhiyuan; Breaker, Ronald R

2014-07-01

Fluoride is a toxic anion found in many natural environments. One of the major bacterial defenses against fluoride is the cell envelope, which limits passage of the membrane-impermeant fluoride anion. Accordingly, compounds that enhance the permeability of bacterial membranes to fluoride should also enhance fluoride toxicity. In this study, we demonstrate that the pore-forming antibiotic gramicidin D increases fluoride uptake in Bacillus subtilis and that the antibacterial activity of this compound is potentiated by fluoride. Polymyxin B, another membrane-targeting antibiotic with a different mechanism of action, shows no such improvement. These results, along with previous findings, indicate that certain compounds that destabilize bacterial cell envelopes can enhance the toxicity of fluoride. Copyright © 2014 Elsevier Ltd. All rights reserved.

Potential fluoride toxicity from oral medicaments: A review

Directory of Open Access Journals (Sweden)

Rizwan Ullah

2017-08-01

Full Text Available The beneficial effects of fluoride on human oral health are well studied. There are numerous studies demonstrating that a small amount of fluoride delivered to the oral cavity decreases the prevalence of dental decay and results in stronger teeth and bones. However, ingestion of fluoride more than the recommended limit leads to toxicity and adverse effects. In order to update our understanding of fluoride and its potential toxicity, we have described the mechanisms of fluoride metabolism, toxic effects, and management of fluoride toxicity. The main aim of this review is to highlight the potential adverse effects of fluoride overdose and poorly understood toxicity. In addition, the related clinical significance of fluoride overdose and toxicity has been discussed.

Growth of fluoride treated Kalanchoe pinnata plants

Energy Technology Data Exchange (ETDEWEB)

Johnson, H N; Applegate, H G

1962-01-01

Kalanchoe pinnata plants can absorb fluoride through roots. The absorption is related to the amount of fluoride applied to the soil. There appeared to be a relationship between the amount of fluoride adsorbed and the subsequent growth of the plants. Plants which adsorbed the largest amounts of fluoride had the greatest increase in growth.

Well Waters Fluoride in Enugu, Nigeria

Directory of Open Access Journals (Sweden)

ISI Ogbu

2012-03-01

Full Text Available Abnormal fluoride levels in drinking water have been associated with adverse health effects. To determine the fluoride content of well waters in Enugu, southeastern Nigeria, water samples from 50 artisan wells chosen by multistage sampling procedure from the 5 zones of Enugu municipality were analyzed in duplicates for their fluoride content. The zonal mean values were 0.60, 0.70, 0.62, 0.62, and 0.63 mg/L for Abakpa Nike, Achara Layout, Obiagu/ Ogui, Trans Ekulu and Uwani, respectively (p<0.05. The mean value for the whole city was 0.63 mg/L. Although, the mean level of fluoride recorded in this study is currently within safe limits (1.5 mg/L, WHO 2011, it is important to monitor continuously the fluoride content of well waters in the municipality in view of the increasing industrial activities going on in the city and heavy reliance on well water for domestic purposes and the widespread use of consumer products containing fluoride.

On the influence of the americium isotopic vector on the cooling time of minor actinides bearing blankets in fast reactors

Directory of Open Access Journals (Sweden)

Kooyman Timothée

2018-01-01

Full Text Available In the heterogeneous minor actinides transmutation approach, the nuclei to be transmuted are loaded in dedicated targets often located at the core periphery, so that long-lived heavy nuclides are turned into shorter-lived fission products by fission. To compensate for low flux level at the core periphery, the minor actinides content in the targets is set relatively high (around 20 at.%, which has a negative impact on the reprocessing of the targets due to their important decay heat level. After a complete analysis of the main contributors to the heat load of the irradiated targets, it is shown here that the choice of the reprocessing order of the various feeds of americium from the fuel cycle depends on the actual limit for fuel reprocessing. If reprocessing of hot targets is possible, it is more interesting to reprocess first the americium feed with a high 243Am content in order to limit the total cooling time of the targets, while if reprocessing of targets is limited by their decay heat, it is more interesting to wait for an increase in the 241Am content before loading the americium in the core. An optimization of the reprocessing order appears to lead to a decrease of the total cooling time by 15 years compared to a situation where all the americium feeds are mixed together when two feeds from SFR are considered with a high reprocessing limit.

The effects of fluoride, strontium, theobromine and their combinations on caries lesion rehardening and fluoridation.

Science.gov (United States)

Lippert, Frank

2017-08-01

The aim was to investigate the effects of fluoride, strontium, theobromine and their combinations on caries lesion rehardening and fluoridation (EFU) under pH cycling conditions. Human enamel specimens were demineralized at 37°C for 24h using a pH 5.0 solution containing 50mM lactic acid and 0.2% Carbopol 907 which was 50% saturated with respect to hydroxyapatite. Lesions were assigned to nine treatment groups (n=16) based on Knoop surface microhardness indentation length. aqueous solutions were: placebo, 11.9mM sodium fluoride (F), 23.8mM sodium fluoride (2×F), 1.1mM strontium chloride hexahydrate (Sr), 1.1mM F theobromine, Sr+theobromine, F+Sr, F+theobromine, F+Sr+theobromine. Lesions were pH cycled for 5d (daily protocol: 3×1min-treatment; 2×60min-demineralization; 4×60min & overnight-artificial saliva). Knoop indentation length was measured again and%surface microhardness recovery (%SMHr) calculated. EFU was determined using the acid-etch technique. Data were analysed using ANOVA. Model showed fluoride dose-response for both variables (2×F>F>placebo). For%SMHr, F+Sr+/-theobromine resulted in more rehardening than F, however less than 2×F. F+theobromine was similar to F. For EFU, F+Sr was inferior to F, F+theobromine and F+Sr+theobromine which were similar and inferior to 2×F. In absence of fluoride, Sr, theobromine or Sr+theobromine were virtually indistinguishable from placebo and inferior to F. It can be concluded that a) strontium aids rehardening but not EFU and only in presence of fluoride; b) theobromine does not appear to offer any anti-caries benefits in this model; c) there are no synergistic effects between strontium and theobromine in the presence or absence of fluoride. Copyright © 2017 Elsevier Ltd. All rights reserved.

Sorption of plutonium and americium on repository, backfill and geological materials relevant to the JNFL low-level radioactive waste repository at Rokkasho-Mura

International Nuclear Information System (INIS)

Baston, G.M.N.; Berry, J.A.; Brownsword, M.; Heath, T.G.; Tweed, C.J.; Williams, S.J.

1995-01-01

An integrated program of batch sorption experiments and mathematical modeling has been carried out to study the sorption of plutonium and americium on a series of repository, backfill and geological materials relevant to the JNFL low-level radioactive waste repository at Rokkasho-Mura. The sorption of plutonium and americium on samples of concrete, mortar, sand/bentonite, tuff, sandstone and cover soil has been investigated. In addition, specimens of bitumen, cation and anion exchange resins, and polyester were chemically degraded. The resulting degradation product solutions, alongside solutions of humic and isosaccharinic acids were used to study the effects on plutonium sorption onto concrete, sand/bentonite and sandstone. The sorption behavior of plutonium and americium has been modeled using the geochemical speciation program HARPHRQ in conjunction with the HATCHES database

National low-level waste management program radionuclide report series, Volume 14: Americium-241

International Nuclear Information System (INIS)

Winberg, M.R.; Garcia, R.S.

1995-09-01

This report, Volume 14 of the National Low-Level Waste Management Program Radionuclide Report Series, discusses the radiological and chemical characteristics of americium-241 ( 241 Am). This report also includes discussions about waste types and forms in which 241 Am can be found and 241 Am behavior in the environment and in the human body

Determination of americium and plutonium in autopsy tissue: methods and problems

International Nuclear Information System (INIS)

Boyd, H.A.; Eutsler, B.C.; McInroy, J.F.

1979-01-01

The current methods used by the tissue analysis program at LASL for the determination of americium and plutonium in autopsy tissue are described. Problems affecting radiochemical yield are discussed. Included are problems associated with sample preparation, separation of plutonium from large amounts of bone ash, and reagent contamination. The average 242 Pu tracer yield for 1800 Pu determinations is 78 +- 12%. The average 242 Am tracer yield is 85 +- 7% for 40 determinations

Determination by gamma-ray spectrometry of the plutonium and americium content of the Pu/Am separation scraps. Application to molten salts; Determination par spectrometrie gamma de la teneur en plutonium et en americium de produits issus de separation Pu/Am. Application aux bains de sels

Energy Technology Data Exchange (ETDEWEB)

Godot, A. [CEA Valduc, Dept. de Traitement des Materiaux Nucleaires, 21 - Is-sur-Tille (France); Perot, B. [CEA Cadarache, Dept. de Technologie Nucleaire, Service de Modelisation des Transferts et Mesures Nucleaires, 13 - Saint-Paul-lez-Durance (France)

2005-07-01

Within the framework of plutonium recycling operations in CEA Valduc (France), americium is extracted from molten plutonium metal into a molten salt during an electrolysis process. The scraps (spent salt, cathode, and crucible) contain extracted americium and a part of plutonium. Nuclear material management requires a very accurate determination of the plutonium content. Gamma-ray spectroscopy is performed on Molten Salt Extraction (MSE) scraps located inside the glove box, in order to assess the plutonium and americium contents. The measurement accuracy is influenced by the device geometry, nuclear instrumentation, screens located between the sample and the detector, counting statistics and matrix attenuation, self-absorption within the spent salt being very important. The purpose of this study is to validate the 'infinite energy extrapolation' method employed to correct for self-attenuation, and to detect any potential bias. We present a numerical study performed with the MCNP computer code to identify the most influential parameters and some suggestions to improve the measurement accuracy. A final uncertainty of approximately 40% is achieved on the plutonium mass. (authors)

A new method for the determination of plutonium and americium using high pressure microwave digestion and alpha-spectrometry or ICP-SMS

International Nuclear Information System (INIS)

Luisier, F.; Corcho Alvarado, J.A.; Froidevaux, P.; Steinmann, P.; Krachler, M.

2009-01-01

Plutonium and americium are radionuclides particularly difficult to measure in environmental samples because they are a-emitters and therefore necessitate a careful separation before any measurement, either using radiometric methods or ICP-SMS. Recent developments in extraction chromatography resins such as Eichrom R TRU and TEVA have resolved many of the analytical problems but drawbacks such as low recovery and spectral interferences still occasionally occur. Here, we report on the use of the new Eichrom R DGA resin in association with TEVA resin and high pressure microwave acid leaching for the sequential determination of plutonium and americium in environmental samples. The method results in average recoveries of 83 ± 15% for plutonium and 73 ± 22% for americium (n = 60), and a less than 10% deviation from reference values of four IAEA reference materials and three samples from intercomparisons exercises. The method is also suitable for measuring 239 Pu in water samples at the μBq/l level, if ICP-SMS is used for the measurement. (author)

A review of slow-release fluoride devices.

Science.gov (United States)

Toumba, K J; Al-Ibrahim, N S; Curzon, M E J

2009-09-01

Fluoride has been used to combat dental caries using a number of different clinical approaches. An exciting relatively new development is fluoride slow-releasing devices that consistently elevate intra-oral fluoride levels of plaque and saliva for prolonged periods of up to two years. The literature on the use of slow-releasing fluoride devices in dentistry were reviewed. A Medline search on key words was carried out. All papers in English were individually reviewed. Slow-releasing fluoride devices have been shown to be effective in elevating salivary fluoride levels in both animals and human studies and to enhance the remineralisation of dental enamel. They have been demonstrated to be safe to use and without the risk of fluoride toxicity. A double blind randomised clinical trial demonstrated 76% fewer new carious surface increment in high caries-risk children after two years. These devices have a number of potential uses in dentistry and in particular have great potential for caries prevention of non-compliant high caries-risk groups.

Effects of fluoridated milk on root dentin remineralization.

Directory of Open Access Journals (Sweden)

Wolfgang H Arnold

Full Text Available The prevalence of root caries is increasing with greater life expectancy and number of retained teeth. Therefore, new preventive strategies should be developed to reduce the prevalence of root caries. The aim of this study was to investigate the effects of fluoridated milk on the remineralization of root dentin and to compare these effects to those of sodium fluoride (NaF application without milk.Thirty extracted human molars were divided into 6 groups, and the root cementum was removed from each tooth. The dentin surface was demineralized and then incubated with one of the following six solutions: Sodium chloride NaCl, artificial saliva, milk, milk+2.5 ppm fluoride, milk+10 ppm fluoride and artificial saliva+10 ppm fluoride. Serial sections were cut through the lesions and investigated with polarized light microscopy and quantitative morphometry, scanning electron microscopy (SEM and energy-dispersive X-ray spectroscopy (EDS. The data were statistically evaluated using a one-way ANOVA for multiple comparisons.The depth of the lesion decreased with increasing fluoride concentration and was the smallest after incubation with artificial saliva+10 ppm fluoride. SEM analysis revealed a clearly demarcated superficial remineralized zone after incubation with milk+2.5 ppm fluoride, milk+10 ppm fluoride and artificial saliva+10 ppm fluoride. Ca content in this zone increased with increasing fluoride content and was highest after artificial saliva+10 ppm fluoride incubation. In the artificial saliva+10 ppm fluoride group, an additional crystalline layer was present on top of the lesion that contained elevated levels of F and Ca.Incubation of root dentin with fluoridated milk showed a clear effect on root dentin remineralization, and incubation with NaF dissolved in artificial saliva demonstrated a stronger effect.

Fluoride Increase in Saliva and Dental Biofilm due to a Meal Prepared with Fluoridated Water or Salt: A Crossover Clinical Study.

Science.gov (United States)

Lima, Carolina V; Tenuta, Livia M A; Cury, Jaime A

2018-06-07

Knowledge about fluoride delivery to oral fluids from foods cooked with fluoridated water and salt is scarce, and no study has evaluated fluoride concentrations in saliva or biofilm during meal consumption. In this randomized double-blind crossover study, 12 volunteers ingested meals (rice, beans, meat, and legumes) prepared with nonfluoridated water and salt (control group), fluoridated water (0.70 mg F/L; water group), and fluoridated salt (183.7 mg F/kg; salt group). Whole saliva was collected before meal ingestion, during mastication, and up to 2 h after meal ingestion. Dental biofilm was collected before and immediately after meal ingestion. Fluoride concentrations in saliva and dental biofilm were determined by an ion-specific electrode. The mean (±standard deviation; n = 4) fluoride concentrations in meals prepared for the control, water, and salt groups were 0.039 ± 0.01, 0.43 ± 0.04, and 1.71 ± 0.32 μg F/g, respectively. The three groups had significantly different fluoride concentrations in saliva collected during mastication (p water > control). The fluoride concentration in saliva returned to baseline 30 min after meal ingestion in the water group but remained high for up to 2 h in the salt group (p = 0.002). The fluoride concentration in biofilm fluid differed only between the salt and control groups (p = 0.008). The mastication of foods cooked with fluoridated water and salt increases fluoride concentrations in oral fluids and may contribute to the local effect of these community-based fluoride interventions on caries control. © 2018 S. Karger AG, Basel.

Estimation of atmospheric fluoride by limed filter papers

International Nuclear Information System (INIS)

Smith, D.R.

1988-09-01

The limed filter paper method of static sampling of atmospheric fluoride is reviewed in this report. Use of the technique, in conjunction with precise measurement of the absorbed fluoride and calibration with dynamic air sampling techniques, to estimate atmospheric fluoride levels, is considered to give only qualitative data (± 50%). The limed filter paper method is site specific due to variations in meteorological conditions. Its main value is to indicate seasonal and annual trends in fluoride exposure of vegetation. Subject to these considerations, the lower and upper limits of atmospheric fluoride exposure and the applicability to atmospheric fluoride estimation under routine or emergency fluoride release conditions are discussed, with special emphasis on the limiting factors

Scandium fluorides

International Nuclear Information System (INIS)

Melnikov, P.; Nalin, M.; Messaddeq, Y.

1997-01-01

A new modification of scandium fluoride has been synthesised. The compound is deficient in fluorine, with the composition ScF 2.76 . It belongs to the tetragonal system, lattice parameters being a=3.792 and c=6.740 A and may be obtained at low temperatures by the decomposition of the precursor NH 4 ScF 4 . The reaction is topotactic, tetragonal parameters of the precursor are a=4.021 and c=6.744 A. Structural relationships with various fluorides and ammonium aminofluorides are discussed. This synthesis route with IR-assisted decomposition should be considered as a soft-chemistry approach. (orig.)

Implications of plutonium and americium recycling on MOX fuel fabrication

International Nuclear Information System (INIS)

Renard, A.; Pilate, S.; Maldague, Th.; La Fuente, A.; Evrard, G.

1995-01-01

The impact of the multiple recycling of plutonium in power reactors on the radiation dose rates is analyzed for the most critical stage in a MOX fuel fabrication plant. The limitation of the number of Pu recycling in light water reactors would rather stem from reactor core physics features. The case of recovering americium with plutonium is also considered and the necessary additions of shielding are evaluated. A comparison between the recycling of Pu in fast reactors and in light water reactors is presented. (author)

Chemical behaviour of trivalent and pentavalent americium in saline NaCl-solutions. Studies of transferability of laboratory data to natural conditions. Interim report. Reported period: 1.2.1993-31.12.1993; Chemisches Verhalten von drei- und fuenfwertigem Americium in Salinen NaCl-Loesungen. Untersuchung der Uebertragbarkeit von Labordaten auf natuerliche Verhaeltnisse. Zwischenbericht. Berichtszeitraum 1.2.1993-31.12.1993

Energy Technology Data Exchange (ETDEWEB)

Runde, W; Kim, J I

1994-09-15

In order to clarify the chemical behaviour of Americium in saline aqueous systems relevant for final storage this study deals with the chemical reactions of trivalent and pentavalent Americium in NaCl-solutions under the influence of radiolysis from its own alpha radiation. The focus of the study was on investigating the geologically relevant reactions, such as hydrolysis or carbonate- and chloride complexing in solid-liquid equilibriums. Comprehensive measurements on solubility and spectroscopic studies in NaCl-solutions were carried out in a CO{sub 2}-free atmosphere and 10{sup -2} atm CO{sub 2} partial pressure. Identification and characterisation of the AM (III) and AM(V) solid phases were supplemented by structural research with the chemically analogue EU (III) and Np(V) compounds. The alpha-radiation induced radiolysis in saline NaCl solutions and the redox behaviour of Americium which was influenced thereby were spectroscopically quantified. (orig.) [Deutsch] Zur Klaerung des chemischen Verhaltens von Americium in endlagerrelevanten salinen aquatischen Systemen befasst sich die vorliegende Arbeit mit den chemischen Reaktionen des drei- und fuenfwertigen Americiums in NaCl-Loesungen unter dem Einfluss der Radiolyse durch die eigene {alpha}-Strahlung. Der Schwerpunkt dieser Arbeit lag auf der Untersuchung der geologisch relevanten Reaktionen, wie Hydrolyse sowie Carbonat- und Chloridkomplexierung in fest-fluessig Gleichgewichtssystemen. Hierzu wurden umfassende Loeslichkeitsmessungen und spektroskopische Untersuchungen in NaCl-Loesungen, sowohl unter CO{sub 2}-freier Atmosphaere als auch unter 10{sup -2} atm CO{sub 2}-Partialdruck, durchgefuehrt. Die Identifizierung und Charakterisierung der Am(III)- und Am(V)-Festphasen wurde ergaenzt durch strukturelle Untersuchungen mit den chemisch analogen Eu(III)- und Np(V)-Verbindungen. Die von der {alpha}-Strahlung induzierte Radiolyse in salinen NaCl-Loesungen und das dadurch beeinflusste Redoxverhalten von Americium

Atmospheric fluoride levels in some Ontario peach orchards

Energy Technology Data Exchange (ETDEWEB)

Drowley, W B; Rayner, A C; Jephcott, C M

1963-10-01

As a result of suture injury to peaches, a survey was taken to determine monthly atmospheric fluoride levels in the soft fruit-growing area of the Niagara Peninsula of Ontario. Although the injury was confined to a few orchards, it was found necessary to locate stations for fluoride sampling over a wide area. The limed-paper candle method was used for fluoride collection. Unwashed and washed peach leaves were analyzed for fluoride content. Fluoride was separated from all samples by the Willard-Winter distillation procedure and estimated colorimetrically. It was found that a general background level of atmospheric fluoride existed in the whole surveyed area and that the levels were highest in and near the area of peach injury. The fluoride content of peach leaves was also highest in this area. The coincidence of high fluoride levels and suture injury to peaches suggests that atmospheric fluoride was the causal agent. When lime sprays were applied to peach trees in the damaged area, a reduction in the incidence of suture injury was observed.

Americium/Curium Vitrification Pilot Tests - Part II

International Nuclear Information System (INIS)

Marra, J.E.; Baich, M.A.; Fellinger, A.P.; Hardy, B.J.; Herman, D.T.; Jones, T.M.; Miller, C.B.; Miller, D.H.; Snyder, T. K.; Stone, M.E.

1998-05-01

Isotopes of americium (Am) and curium (Cm) were produced in the past at the Savannah River Site (SRS) for research, medical, and radiological applications. These highly radioactive and valuable isotopes have been stored in an SRS reprocessing facility for a number of years. Vitrification of this solution will allow the material to be more safely stored until it is transported to the DOE Oak Ridge Reservation for use in research and medical applications. A previous paper described operation results from the Am-Cm Melter 2A pilot system, a full-scale non-radioactive pilot facility. This paper presents the results from continued testing in the Pilot Facility and also describes efforts taken to look at alternative vitrification process operations and flowsheets designed to address the problems observed during melter 2A pilot testing

Behavior of americium in aqueous carbonate systems

Energy Technology Data Exchange (ETDEWEB)

Silva, R.J.

1983-11-01

The solubilities of crystalline Am(OH)/sub 3/ and AmOHCO/sub 3/ were measured at 25/sup 0/C in aqueous solutions of 0.1 M NaClO/sub 4/ by determination of the solution concentrations of Am. Prior to use in the measurements, the solid materials were characterized by their x-ray powder diffraction patterns. The solubility product quotients were calculated from the experimental data. The hydrolysis quotients of Am/sup 3 +/ were also estimated from the hydroxide solubility data. Using the thermodynamic data derived from these experiments and the recently reported formation constants for the Am/sup 3 +/ carbonate complexes, the solid phases and concentrations of solution species of americium in several aqueous carbonate systems were calculated using the computer code MINEQL. 20 references, 1 figure, 1 table.

Adverse effects of fluoride towards thyroid hormone metabolism

Directory of Open Access Journals (Sweden)

Enggar Abdullah Idris MZ

2008-03-01

Full Text Available An easily ionized fluoride compound like Sodium Fluoride (NaF has been used thus far as a dental caries prevention substance. However, fluoride ions also have a negative effect because it is very toxic. Several types of research on the effect of fluoride on guinea pigs and human beings indicate the presence synthesis obstruction of T3 and T4 that causes declined production, known as hypothyroidism. Hypothyroidism condition may obstruct tissue growth process and metabolism so as to impact various body organ systems. Preventive efforts against hypothyroidism caused by fluoride include avoiding diffusible fluoride compound intake, like NaF, in a long run systemic use, whereas efforts to overcome fluoride intoxication include consuming food that is rich in calcium, vitamin D, and antioxidant.

Worldwide bioassay data resources for plutonium/americium internal dosimetry studies

International Nuclear Information System (INIS)

Miller, G.; Bertelli, L.; Little, T.; Guilmette, R.; Riddell, T.; Filipy, R.

2005-01-01

Full text: Biokinetic models are the scientific underpinning of internal dosimetry. These models describe how materials of interest taken into the body by various routes (for example inhalation) are transported through the body, allowing the modelling of bioassay measurements and the estimation of radiation dose. The International Commission on Radiation Protection (ICRP) publishes biokinetic models for use in internal dosimetry. These models represent the consensus judgement of a committee of experts, based on human and animal data. Nonetheless, it is important to validate biokinetic models using directly applicable data, in a scientifically transparent manner, especially for internal dosimetry research purposes (as opposed to radiation protection), as in epidemiology studies. Two major goals would be to determine individual variations of model parameters for the purpose of assessing this source of uncertainty in internal dose calculations, and to determine values of workplace specific parameters (such as particle solubility in lung fluids) for different representative workplaces. Furthermore, data on the observed frequency of intakes under various conditions can be used in the interpretation of bioassay data. All of the above may be couched in the terminology of Bayesian statistical analysis and amount to the determination of the Bayesian prior probability distributions needed in a Bayesian interpretation of bioassay data. The authors have direct knowledge of several significant databases of plutonium/americium bioassay data (including autopsy data). The purpose of this paper is to acquaint the worldwide community with these resources and to invite others who may know of other such databases to participate with us in a publication that would document the content, form, and the procedures for seeking access to these databases. These databases represent a tremendous scientific resource in this field. Examples of databases known to the authors include: the

XRD monitoring of α self-irradiation in uranium-americium mixed oxides.

Science.gov (United States)

Horlait, Denis; Lebreton, Florent; Roussel, Pascal; Delahaye, Thibaud

2013-12-16

The structural evolution under (241)Am self-irradiation of U(1-x)Am(x)O(2±δ) transmutation fuels (with x ≤ 0.5) was studied by X-ray diffraction (XRD). Samples first underwent a preliminary heat treatment performed under a reducing atmosphere (Ar/H2(4%)) aiming to recover the previously accumulated structural defects. Over all measurements (carried out over up to a full year and for integrated doses up to 1.5 × 10(18) α-decay events·g(-1)), only fluorite U(1-x)Am(x)O(2±δ) solid solutions were observed. Within a few days after the end of the heat treatment, each of the five studied samples was slowly oxidized as a consequence of their move to air atmosphere, which is evidenced by XRD by an initial sharp decrease of the unit cell parameter. For the compounds with x ≤ 0.15, this oxidation occurred without any phase transitions, but for U0.6Am0.4O(2±δ) and U0.5Am0.5O(2±δ), this process is accompanied by a transition from a first fluorite solid solution to a second oxidized one, as the latter is thermodynamically stable in ambient conditions. In the meantime and after the oxidation process, (241)Am α self-irradiation caused a structural swelling up to ∼0.8 vol %, independently of the sample composition. The kinetic constants of swelling were also determined by regression of experimental data and are, as expected, dependent on x and thus on the dose rate. The normalization of these kinetic constants by sample α-activity, however, leads to very close swelling rates among the samples. Finally, evolutions of microstrain and crystallite size were also monitored, but for the considered dose rates and cumulated doses, α self-irradiation was found, within the limits of the diffractometer used, to have almost no impact on these characteristics. Microstrain was found to be influenced instead by the americium content in the materials (i.e., by the impurities associated with americium starting material and the increase of cationic charge heterogeneity with

Fluoride and Water (For Parents)

Science.gov (United States)

... risk of tooth decay" on the label. The Controversy Over Fluoride Opponents of water fluoridation have questioned ... Us Contact Us Partners Editorial Policy Permissions Guidelines Privacy Policy & Terms of Use Notice of Nondiscrimination Visit ...

Physiologic Conditions Affect Toxicity of Ingested Industrial Fluoride

OpenAIRE

Richard Sauerheber

2013-01-01

The effects of calcium ion and broad pH ranges on free fluoride ion aqueous concentrations were measured directly and computed theoretically. Solubility calculations indicate that blood fluoride concentrations that occur in lethal poisonings would decrease calcium below prevailing levels. Acute lethal poisoning and also many of the chronic effects of fluoride involve alterations in the chemical activity of calcium by the fluoride ion. Natural calcium fluoride with low solubility and toxicity ...

Fluoride Removal from Water by Reverse Osmosis Membrane

Directory of Open Access Journals (Sweden)

Sara Namavar

2013-09-01

Full Text Available As fluoride concentration in drinking water is one of the effective parameters in human health, finding the way to remove excess amount of fluoride from drinking water is very important in water supply projects. Today, with developing in technology and finding new methods, the use of membrane technology for producing fresh water get improved. In this study the efficiency of reverse osmosis method to remove fluoride from water was investigated. Initial concentration of fluoride, sulfate and electrical conductivity in feed water and the effect of associated cation with fluoride ion were studied. All tests adapted from “Standard Methods for Examination of Water and Wastewater”. Determination of fluoride concentration was done according the standard SPANDS method by using a spectrophotometer DR/5000. Obtain results show that with increasing in concentration of fluoride and sulfate and electrical conductivity in feed water the efficiency of RO membrane to remove fluoride reduced. In addition, this efficiency for CaF2 was higher than NaF.

Development of analytical methods for the separation of plutonium, americium, curium and neptunium from environmental samples

Energy Technology Data Exchange (ETDEWEB)

Salminen, S.

2009-07-01

In this work, separation methods have been developed for the analysis of anthropogenic transuranium elements plutonium, americium, curium and neptunium from environmental samples contaminated by global nuclear weapons testing and the Chernobyl accident. The analytical methods utilized in this study are based on extraction chromatography. Highly varying atmospheric plutonium isotope concentrations and activity ratios were found at both Kurchatov (Kazakhstan), near the former Semipalatinsk test site, and Sodankylae (Finland). The origin of plutonium is almost impossible to identify at Kurchatov, since hundreds of nuclear tests were performed at the Semipalatinsk test site. In Sodankylae, plutonium in the surface air originated from nuclear weapons testing, conducted mostly by USSR and USA before the sampling year 1963. The variation in americium, curium and neptunium concentrations was great as well in peat samples collected in southern and central Finland in 1986 immediately after the Chernobyl accident. The main source of transuranium contamination in peats was from global nuclear test fallout, although there are wide regional differences in the fraction of Chernobyl-originated activity (of the total activity) for americium, curium and neptunium. The separation methods developed in this study yielded good chemical recovery for the elements investigated and adequately pure fractions for radiometric activity determination. The extraction chromatographic methods were faster compared to older methods based on ion exchange chromatography. In addition, extraction chromatography is a more environmentally friendly separation method than ion exchange, because less acidic waste solutions are produced during the analytical procedures. (orig.)

FLUORIDE: A REVIEW OF USE AND EFFECTS ON HEALTH.

Science.gov (United States)

Kanduti, Domen; Sterbenk, Petra; Artnik, Barbara

2016-04-01

Appropriate oral health care is fundamental for any individual's health. Dental caries is still one of the major public health problems. The most effective way of caries prevention is the use of fluoride. The aim of our research was to review the literature about fluoride toxicity and to inform physicians, dentists and public health specialists whether fluoride use is expedient and safe. Data we used in our review were systematically searched and collected from web pages and documents published from different international institutions. Fluoride occurs naturally in our environment but we consume it in small amounts. Exposure can occur through dietary intake, respiration and fluoride supplements. The most important factor for fluoride presence in alimentation is fluoridated water. Methods, which led to greater fluoride exposure and lowered caries prevalence, are considered to be one of the greatest accomplishments in the 20th century`s public dental health. During pregnancy, the placenta acts as a barrier. The fluoride, therefore, crosses the placenta in low concentrations. Fluoride can be transmitted through the plasma into the mother's milk; however, the concentration is low. The most important action of fluoride is topical, when it is present in the saliva in the appropriate concentration. The most important effect of fluoride on caries incidence is through its role in the process of remineralization and demineralization of tooth enamel. Acute toxicity can occur after ingesting one or more doses of fluoride over a short time period which then leads to poisoning. Today, poisoning is mainly due to unsupervised ingestion of products for dental and oral hygiene and over-fluoridated water. Even though fluoride can be toxic in extremely high concentrations, it`s topical use is safe. The European Academy of Paediatric Dentistry (EAPD) recommends a preventive topical use of fluoride supplements because of their cariostatic effect.

Strontium-90 fluoride data sheet

Energy Technology Data Exchange (ETDEWEB)

Fullam, H.T.

1981-06-01

This report is a compilation of available data and appropriate literature references on the properties of strontium-90 fluoride and nonradioactive strontium fluoride. The objective of the document is to compile in a single source pertinent data to assist potential users in the development, licensing, and use of /sup 90/SrF/sub 2/-fueled radioisotope heat sources for terrestrial power conversion and thermal applications. The report is an update of the Strontium-90 Fluoride Data Sheet (BNWL-2284) originally issued in April 1977.

Potential fluoride toxicity from oral medicaments: A review

OpenAIRE

Rizwan Ullah; Muhammad Sohail Zafar; Nazish Shahani

2017-01-01

The beneficial effects of fluoride on human oral health are well studied. There are numerous studies demonstrating that a small amount of fluoride delivered to the oral cavity decreases the prevalence of dental decay and results in stronger teeth and bones. However, ingestion of fluoride more than the recommended limit leads to toxicity and adverse effects. In order to update our understanding of fluoride and its potential toxicity, we have described the mechanisms of fluoride metabolism, tox...

Low-levels of fluoride in plaque and saliva and their effects on the demineralisation and remineralisation of enamel; role of fluoride toothpastes.

Science.gov (United States)

Lynch, R J M; Navada, R; Walia, R

2004-01-01

To summarise support for current consensus on the likely means by which fluoride toothpastes reduce caries and review some relevant studies of the effect of low levels of fluoride on the demineralisation and remineralisation of enamel. The major anti-caries effect of fluoride toothpastes is thought to result from small but protracted elevations in levels of fluoride in plaque and saliva. Fluoride incorporated into enamel systemically does not reduce enamel solubility sufficiently to exert an anti-caries effect. Fluoride has the potential to exert an anti-caries benefit largely through three mechanisms; inhibition of demineralisation, promotion of remineralisation and interference with bacterial growth and metabolism. However, the low levels of fluoride thought to influence caries are insufficient to have a significant effect via the latter mechanism. Thus reductions in caries resulting from the use of fluoride toothpastes can be linked to modification of the demineralisation/remineralisation balance by direct effects on dental mineral exerted topically by low levels of fluoride. Numerous in vitro studies have shown that low levels of fluoride, typical of those found after many hours in resting plaque and saliva, and resulting from the regular use of fluoride toothpastes, can have a profound effect on enamel demineralisation and remineralisation.

Fluoride release and cariostatic potential of orthodontic adhesives with and without daily fluoride rinsing.

NARCIS (Netherlands)

Chin, M.Y.; Sandham, A.; Rumachik, E.N.; Ruben, J.L.; Huysmans, M.C.D.N.J.M.

2009-01-01

INTRODUCTION: In this study, we aimed to evaluate the fluoride-release profiles and caries lesion development in an enamel model with brackets cemented with 4 orthodontic adhesives with and without daily fluoride exposure. METHODS: Four orthodontic adhesives (Ketac Cem mu, 3M ESPE, Seefeld, Germany;

Fluoride release and cariostatic potential of orthodontic adhesives with and without daily fluoride rinsing

NARCIS (Netherlands)

Chin, Yeen; Sandham, John; Rumachik, Elena N.; Ruben, Jan L.; Huysmans, Marie-Charlotte D. N. J. M.

2009-01-01

Introduction: In this study, we aimed to evaluate the fluoride-release profiles and caries lesion development in an enamel model with brackets cemented with 4 orthodontic adhesives with and without daily fluoride exposure. Methods: Four orthodontic adhesives (Ketac Cem mu, 3M ESPE, Seefeld, Germany;

Acute toxicity of ingested fluoride.

Science.gov (United States)

Whitford, Gary Milton

2011-01-01

This chapter discusses the characteristics and treatment of acute fluoride toxicity as well as the most common sources of overexposure, the doses that cause acute toxicity, and factors that can influence the clinical outcome. Cases of serious systemic toxicity and fatalities due to acute exposures are now rare, but overexposures causing toxic signs and symptoms are not. The clinical course of systemic toxicity from ingested fluoride begins with gastric signs and symptoms, and can develop with alarming rapidity. Treatment involves minimizing absorption by administering a solution containing calcium, monitoring and managing plasma calcium and potassium concentrations, acid-base status, and supporting vital functions. Approximately 30,000 calls to US poison control centers concerning acute exposures in children are made each year, most of which involve temporary gastrointestinal effects, but others require medical treatment. The most common sources of acute overexposures today are dental products - particularly dentifrices because of their relatively high fluoride concentrations, pleasant flavors, and their presence in non-secure locations in most homes. For example, ingestion of only 1.8 ounces of a standard fluoridated dentifrice (900-1,100 mg/kg) by a 10-kg child delivers enough fluoride to reach the 'probably toxic dose' (5 mg/kg body weight). Factors that may influence the clinical course of an overexposure include the chemical compound (e.g. NaF, MFP, etc.), the age and acid-base status of the individual, and the elapsed time between exposure and the initiation of treatment. While fluoride has well-established beneficial dental effects and cases of serious toxicity are now rare, the potential for toxicity requires that fluoride-containing materials be handled and stored with the respect they deserve. Copyright © 2011 S. Karger AG, Basel.

Calibration procedures for in vivo sodium iodide spectrometry of plutonium and americium in the human lung

International Nuclear Information System (INIS)

Umbarger, C.J.; Jett, J.H.

1976-01-01

This paper describes the calibration techniques and associated error analysis for the in vivo measurement by NaI spectrometry of heavy elements in the lung, specifically plutonium and americium. A very brief description of the instrumentation system is included

Inhibition of cellular oxidation by fluoride

Energy Technology Data Exchange (ETDEWEB)

Borei, H

1945-01-01

An attempt has been made to investigate the inhibition by fluoride of the oxidative processes which occur in the cell by way of the cytochrome oxidase-cytochrome system. Some chemical and physical properties of the fluoride ion are discussed, together with certain quantitative methods for the determination of fluoride. An exhaustive review of the literature concerning the effect of fluoride on enzymic processes has been compiled. The experiments have shown that the point of the attack by fluoride is to be found among the cytochromes. The inhibitory mechanism appears to be such that the haemoprotein is prevented from taking part in the preceding and succeeding links in the reaction chain. The blocking action leaves the prosthetic group of the haemoprotein completely unchanged. The experimental results indicate the formation of a fluorophosphoprotein complex, analogous to that found in the case of enolase. Magnesium may possibly play a part in this process.

Acute toxicity of uranium hexafluoride, uranyl fluoride and hydrogen fluoride

International Nuclear Information System (INIS)

Just, R.A.

1988-01-01

Uranium hexafluoride (UF 6 ) released into the atmosphere will react rapidly with moisture in the air to form the hydrolysis products uranyl fluoride (UO 2 F 2 ) and hydrogen fluoride (HF). Uranium compounds such as UF 6 and UO 2 F 2 exhibit both chemical toxicity and radiological effects, while HF exhibits only chemical toxicity. This paper describes the development of a methodology for assessing the human health consequences of a known acute exposure to a mixture of UF 6 , UO 2 F 2 , and HF. 4 refs., 2 figs., 5 tabs

Evaluation of toxic action of fluorides on agricultural plants

Directory of Open Access Journals (Sweden)

V. N. Grishko

2007-03-01

Full Text Available The toxicity of potassium fluoride, sodium fluoride and ammonium fluoride for pea, maize, oat and onion was studied. It was found that the level of the toxic influence had grown with increase of fluoride concentration in the media of growth (from 5 to 100 mg of F–/l. By increase of the toxic influence the agricultural crops are disposed in the following row: oat < onion < maize < pea. Ammonium fluoride demonstrates lesser toxicity, than potassium and sodium fluorides. Under low concentrations of fluoride compounds (5 and 10 mg of F–/l stimulation of roots growth is noted only for the oat.

Determination of Fluoride in Different Toothpaste Formulations

International Nuclear Information System (INIS)

Kamau, N.G.; Njoroge, M.; Njau, M.

1998-01-01

Fluoride ion selective electrode was used to determine fluoride ion concentrations in seven brands of toothpaste. These were the only available formulations found in Kenya. The brands were classified into three groups-fluoridated, non fluoridated or not indicated. However, there was no independent indication of their quantitative composition. The analysed brands had fluoride content between 0.0033% and 0.096%. These values compared favourably with those obtained elsewhere. The calculated lowest limit of detection (LLD) was 0.01 ppmF- . The mean calibration curve gave a slope of of -50.0mV. which was not significantly different from the theoretical value of 5.88mV at 23 degrees celsius at 95% confidence level

Anhydrous hydrogen fluoride electrolyte battery. [Patent application

Science.gov (United States)

Not Available

1972-06-26

It is an object of the invention to provide a primary cell or battery using ammonium fluoride--anhydrous hydrogen fluoride electrolyte having improved current and power production capabilities at low temperatures. It is operable at temperatures substantially above the boiling point of hydrogen fluoride. (GRA)

Fluoride ions vs removal technologies: A study

Directory of Open Access Journals (Sweden)

Jagvir Singh

2016-11-01

Full Text Available Literature reported that drinking water is a precious and scarce resource and it has to be protected and kept free from any kind of contamination. Further, it has to be used carefully without wasting. Literature also reported that fluoride bearing rocks are abundant in India, as a result, fluoride leaches out and contaminates the adjacent water and soil resources. A high concentration of fluoride ions in ground water increases up to more than 30 mg/L. This high concentration of fluoride ions causes many harmful and dangerous effects on our datum. Fluoride ions in larger quantities i.e. 20–80 mg/day taken over a period of 10–20 years result in crippling and skeletal fluorosis, severely damaging the bone. In the present scenario, there is a continuously increasing worldwide concern for the development of fluoride treatment technologies. Possibilities of reducing the high fluorine content in groundwater are by defluorination process/dilution with the surface water which is a very simple technique but the addition of Ca2+ ions to a solution in contact with fluorite when experimented in distilled water caused an appreciable decrease in fluoride concentration. In this review article, we emphasized the relationship between high concentrations of fluoride ions and their compounds and their health impact.

Comparison of Americium-Beryllium neutron spectrum obtained using activation foil detectors and NE-213 spectrometer

International Nuclear Information System (INIS)

Sunny, Sunil; Subbaiah, K.V.; Selvakumaran, T.S.

1999-01-01

Neutron spectrum of Americium - Beryllium (α,n) source is measured with two different spectrometers vis-a-vis activation foils (foil detectors) and NE-213 organic scintillator. Activity induced in the foils is measured with 4π-β-γ sodium iodide detector by integrating counts under photo peak and the saturation activity is found by correcting to elapsed time before counting. The data on calculated activity is fed into the unfolding code, SAND-II to obtain neutron spectrum. In the case of organic scintillator, the pulse height spectrum is obtained using MCA and this is processed with unfolding code DUST in order to get neutron spectrum. The Americium - Beryllium (α,n) neutron spectrum thus obtained by two different methods is compared. It is inferred that the NE-213 scintillator spectrum is in excellent agreement with the values beyond 1MeV. Neutron spectrum obtained by activation foils depends on initial guess spectrum and is found to be in reasonable agreement with NE-213 spectrum. (author)

Risk Assessment of Fluoride Intake from Tea in the Republic of Ireland and its Implications for Public Health and Water Fluoridation

Science.gov (United States)

Waugh, Declan T.; Potter, William; Limeback, Hardy; Godfrey, Michael

2016-01-01

The Republic of Ireland (RoI) is the only European Country with a mandatory national legislation requiring artificial fluoridation of drinking water and has the highest per capita consumption of black tea in the world. Tea is a hyperaccumulator of fluoride and chronic fluoride intake is associated with multiple negative health outcomes. In this study, fifty four brands of the commercially available black tea bag products were purchased and the fluoride level in tea infusions tested by an ion-selective electrode method. The fluoride content in all brands tested ranged from 1.6 to 6.1 mg/L, with a mean value of 3.3 mg/L. According to our risk assessment it is evident that the general population in the RoI is at a high risk of chronic fluoride exposure and associated adverse health effects based on established reference values. We conclude that the culture of habitual tea drinking in the RoI indicates that the total cumulative dietary fluoride intake in the general population could readily exceed the levels known to cause chronic fluoride intoxication. Evidence suggests that excessive fluoride intake may be contributing to a wide range of adverse health effects. Therefore from a public health perspective, it would seem prudent and sensible that risk reduction measures be implemented to reduce the total body burden of fluoride in the population. PMID:26927146

Structural study of chlorine tri-fluoride and bromine penta-fluoride in liquid and solid phase

International Nuclear Information System (INIS)

Rousson, R.

1973-01-01

This research thesis reports the structural study of chlorine tri-fluoride and bromine penta-fluoride between 20 C and about -265 C. After some generalities on these compounds and a presentation of the experimental technique, the author reports and discusses results obtained with these both compounds: Raman spectrum for the liquid and for the solid phase, infrared spectrum for the solid phase, calorimetric measurements. In the case of chlorine tri-fluoride, the author studies the evolution of the liquid spectrum with temperature, shows the existence of an intermediate solid phase, and compares results obtained by Raman spectroscopy and nuclear magnetic resonance. He also applies to bromine penta-fluoride an analysis of normal coordinates of a XF 5 molecule: relationship between force constants and vibration frequencies, application of Wilson method, resolution of the molecular equation, determination of normal vibration modes [fr

Quantitative determination of americium and curium in solutions using potassium tungstophosphate

International Nuclear Information System (INIS)

Chistyakov, V.M.; Baranov, A.A.; Erin, E.A.; Timoaeev, G.A.

1990-01-01

Two methods of americium (4) and curium (4) titration-replacement and redox ones - have been considered. According to the replacement method thorium nitrate solution was used as a titrant and the final point of titration was determined spectophotometrically. Using the method developed, on the basis of experimental data, the composition of thorium (4) complex with potassium tungstophosphate was determined. In case of the redox titration sodium nitrite was used, and the final titration point was indicated either spectrophotometrically or potentiometrically

Analysis of large soil samples for actinides

Science.gov (United States)

Maxwell, III; Sherrod, L [Aiken, SC

2009-03-24

A method of analyzing relatively large soil samples for actinides by employing a separation process that includes cerium fluoride precipitation for removing the soil matrix and precipitates plutonium, americium, and curium with cerium and hydrofluoric acid followed by separating these actinides using chromatography cartridges.

Fluoride ions vs removal technologies: A study

OpenAIRE

Singh, Jagvir; Singh, Prashant; Singh, Anuradha

2016-01-01

Literature reported that drinking water is a precious and scarce resource and it has to be protected and kept free from any kind of contamination. Further, it has to be used carefully without wasting. Literature also reported that fluoride bearing rocks are abundant in India, as a result, fluoride leaches out and contaminates the adjacent water and soil resources. A high concentration of fluoride ions in ground water increases up to more than 30 mg/L. This high concentration of fluoride ions ...

Water fluoridation in 40 Brazilian cities: 7 year analysis

Directory of Open Access Journals (Sweden)

Suzely Adas Saliba MOIMAZ

2013-01-01

Full Text Available Objectives Fluoride levels in the public water supplies of 40 Brazilian cities were analyzed and classified on the basis of risk/benefit balance. Material and Methods Samples were collected monthly over a seven-year period from three sites for each water supply source. The samples were analyzed in duplicate in the laboratory of the Center for Research in Public Health - UNESP using an ion analyzer coupled to a fluoride-specific electrode. Results A total of 19,533 samples were analyzed, of which 18,847 were artificially fluoridated and 686 were not artificially fluoridated. In samples from cities performing water fluoridation, 51.57% (n=9,720 had fluoride levels in the range of 0.55 to 0.84 mg F/L; 30.53% (n=5,754 were below 0.55 mg F/L and 17.90% (n=3,373 were above 0.84 mg F/L (maximum concentration=6.96 mg F/L. Most of the cities performing fluoridation that had a majority of samples with fluoride levels above the recommended parameter had deep wells and more than one source of water supply. There was some variability in the fluoride levels of samples from the same site and between collection sites in the same city. Conclusions The majority of samples from cities performing fluoridation had fluoride levels within the range that provides the best combination of risks and benefits, minimizing the risk of dental fluorosis while preventing dental caries. The conduction of studies about water distribution systems is suggested in cities with high natural fluoride concentrations in order to optimize the use of natural fluoride for fluoridation costs and avoid the risk of dental fluorosis.

Vitrification of F-area americium/curium: feasibility study and preliminary process recommendation

International Nuclear Information System (INIS)

Ramsey, W.G.; Miller, D.; Minichan, R.; Coleman, L.; Schumacher, R.; Hardy, B.; Jones, R.

1994-01-01

Work was performed to identify a process to vitrify the contents of F- canyon Tank 17.1. Tank 17.1 contains the majority of americium (Am) and curium (Cm) contained in the DOE Complex. Oak Ridge National Laboratory (ORNL) has made a formal request for this material as fuel for production of Cf252 and other transplutonium actinides. The Am and Cm (and associated lanthanide fission products) are currently in nitric acid solution. Transportation of the intensely radioactive Am/Cm in liquid form is not considered possible. As a result, the material will either be solidified and shipped to ORNL or discarded to the Tank Farm. Nuclear Materials Processing Technology (NMPT), therefore, requested Defense Waste Processing Technology (DWPT) to determine if the Tank 17.1 material could be vitrified, and if it was vitrified could the americium and curium be successfully recovered. Research was performed to determine if the Tank 17.1 contents could indeed be mixed with glass formers and vitrified. Additional studies identified critical process parameters such as heat loading, melter requirements, off-gas evolution, etc. Discussions with NMPT personnel were initiated to determine existing facilities where this work could be accomplished safely. A process has been identified which will convert the Am/Cm material into approximately 300kg of glass

The transmutation of americium: the Ecrix experiments in Phenix

International Nuclear Information System (INIS)

Garnier, J.C.; Schmidt, N.; Croixmarie, Y.; Ottaviani, J.P.; Varaine, F.; Saint Jean, C. de

1999-01-01

The first americium transmutation experiment in a specific target in PHENIX will occur with the ECRIX-B and ECRIX-H experiments. Beside material testing, the objective is also to represent a concept of transmutation whose specificity is to enhance the kinetics of transmutation by using a moderated spectrum. The moderator materials will be 11 B 4 C and CaH 2 for ECRIX-B and ECRIXH respectively, the irradiation conditions have been predicted for both the neutronics and thermal. The targets (MgO-AmO X pellets) are manufactured in the ATALANTE laboratory and the design is performed according to the PHENIX operating conditions. (authors)

Robotic sample preparation for radiochemical plutonium and americium analyses

International Nuclear Information System (INIS)

Stalnaker, N.; Beugelsdijk, T.; Thurston, A.; Quintana, J.

1985-01-01

A Zymate robotic system has been assembled and programmed to prepare samples for plutonium and americium analyses by radioactivity counting. The system performs two procedures: a simple dilution procedure and a TTA (xylene) extraction of plutonium. To perform the procedures, the robotic system executes 11 unit operations such as weighing, pipetting, mixing, etc. Approximately 150 programs, which require 64 kilobytes of memory, control the system. The system is now being tested with high-purity plutonium metal and plutonium oxide samples. Our studies indicate that the system can give results that agree within 5% at the 95% confidence level with determinations performed manually. 1 ref., 1 fig., 1 tab

THE USE OF FLUORIDE AND ITS EFFECT ON HEALTH

Directory of Open Access Journals (Sweden)

Domen Kanduti

2016-07-01

Full Text Available Appropriate oral health care is fundamental for any individual’s health. Dental caries is still one of the major public health problems. The most effective way of caries prevention is the use of fluoride. Fluoride occurs naturally in our environment and is always present in our lives. However, the concentration differs from area to area. Exposure can occur through diet, respiration and fluoride supplements. During pregnancy, the placenta acts as a barrier. The fluoride, therefore, crosses the placenta in low concentrations. Drinking water in Slovenia is not fluoridated; the amount of naturally present fluoride is very low. Fluoride can be toxic in extremely high concentrations. The most important effect of fluoride on caries incidence is through its role in the process of remineralisation and demineralisation of tooth enamel. The European Academy of Paediatric Dentistry (EAPD recommends a preventive topical use of fluoride supplements because of their cariostatic effect. 

Histopathological changes of renal tissue following sodium fluoride administration in two consecutive generations of mice. Correlation with the urinary elimination of fluoride.

Science.gov (United States)

Dimcevici Poesina, Nicoleta; Bălălău, Cristian; Nimigean, Vanda Roxana; Nimigean, Victor; Ion, Ion; Baconi, Daniela; Bârcă, Maria; Băran Poesina, Violeta

2014-01-01

The present study was designed to investigate the toxic effects (evaluated as histopathological changes) of sodium fluoride on the kidney in two consecutive generations of NMRI mice. An attempt to correlate the toxicity with the urinary elimination of fluoride has been made, as urinary fluoride excretion has been widely used as an indicator of fluoride intake and exposure. Six mixed (males and females) animal groups have been constituted by dividing the populations of mice derived from pregnant females (named "mothers" 0.5 mg sodium fluoride) treated with 0.5 mg sodium fluoride by daily gavage and pregnant females (named "mothers" 0.25 mg sodium fluoride) treated with 0.25 mg sodium fluoride by daily gavage; three types of sodium fluoride treatments were administrated: homeopathic, allopathic-homeopathic and allopathic. When the animals reached the adulthood, by randomization, they were selected in pairs for giving birth to the second generation of mice. No treatments were administrated to the second generation of mice; thus, the urinary elimination of fluoride in the second generation is attributed to exposure at sodium fluoride before birth. The administration of sodium fluoride to the first generation (F1) is realized until the mice reached the adulthood. For the first generation, the urine was collected at three times, every three weeks: at the age of four weeks, seven weeks and 11 weeks; single sampling urine, at the age of four weeks, has been conducted for the second generation. The urine samples have been analyzed using the ion selective electrode method for fluoride. For the histopathological examination, the animals were killed by cervical dislocation; the kidneys were collected in a 10% formalin solution. The preparation of samples for optical microscopy was realized with Hematoxylin-Eosin staining. The results indicate that the elimination of fluoride was similar (at the second evaluation, at 7-week-old of the first generation) for the both generations

In situ characterization of uranium and americium oxide solid solution formation for CRMP process: first combination of in situ XRD and XANES measurements.

Science.gov (United States)

Caisso, Marie; Picart, Sébastien; Belin, Renaud C; Lebreton, Florent; Martin, Philippe M; Dardenne, Kathy; Rothe, Jörg; Neuville, Daniel R; Delahaye, Thibaud; Ayral, André

2015-04-14

Transmutation of americium in heterogeneous mode through the use of U1-xAmxO2±δ ceramic pellets, also known as Americium Bearing Blankets (AmBB), has become a major research axis. Nevertheless, in order to consider future large-scale deployment, the processes involved in AmBB fabrication have to minimize fine particle dissemination, due to the presence of americium, which considerably increases the risk of contamination. New synthesis routes avoiding the use of pulverulent precursors are thus currently under development, such as the Calcined Resin Microsphere Pelletization (CRMP) process. It is based on the use of weak-acid resin (WAR) microspheres as precursors, loaded with actinide cations. After two specific calcinations under controlled atmospheres, resin microspheres are converted into oxide microspheres composed of a monophasic U1-xAmxO2±δ phase. Understanding the different mechanisms during thermal conversion, that lead to the release of organic matter and the formation of a solid solution, appear essential. By combining in situ techniques such as XRD and XAS, it has become possible to identify the key temperatures for oxide formation, and the corresponding oxidation states taken by uranium and americium during mineralization. This paper thus presents the first results on the mineralization of (U,Am) loaded resin microspheres into a solid solution, through in situ XAS analysis correlated with HT-XRD.

Method for identifying particulate fluoride compounds

Energy Technology Data Exchange (ETDEWEB)

Tufts, B J

1960-01-01

A method is described for identifying particulates containing fluorides and other complex fluorine compounds such as fluorosilicate in samples collected on membrane filters. The filter is treated with lead chloride to precipitate lead chlorofluoride at each fluoride-containing spot. This microspot is identified by examination in a light microscope. Sulfate and phosphate, which also precipitate if present, can be distinguished and do not interfere. Calibrations are given for the fluorides and the more insoluble salts, relating the original particle size to the reaction site size. Thus, the mass of the particles can be calculated. Results of some field tests in an area of fluoride pollution are given, and compared with standard testing procedures.

Plutonium, americium, and uranium in blow-sand mounds of safety-shot sites at the Nevada Test Site and the Tonopah Test Range

International Nuclear Information System (INIS)

Essington, E.H.; Gilbert, R.O.; Wireman, D.L.; Brady, D.N.; Fowler, E.B.

1977-01-01

Blow-sand mounds or miniature sand dunes and mounds created by burrowing activities of animals were investigated by the Nevada Applied Ecology Group (NAEG) to determine the influence of mounds on plutonium, americium, and uranium distributions and inventories in areas of the Nevada Test Site and Tonopah Test Range. Those radioactive elements were added to the environment as a result of safety experiments of nuclear devices. Two studies were conducted. The first was to estimate the vertical distribution of americium in the blow-sand mounds and in the desert pavement surrounding the mounds. The second was to estimate the amount or concentration of the radioactive materials accumulated in the mound relative to the desert pavement. Five mound types were identified in which plutonium, americium, and uranium concentrations were measured: grass, shrub, complex, animal, and diffuse. The mount top (that portion above the surrounding land surface datum), the mound bottom (that portion below the mound to a depth of 5 cm below the surrounding land surface datum), and soil from the immediate area surrounding the mound were compared separately to determine if the radioactive elements had concentrated in the mounds. Results of the studies indicate that the mounds exhibit higher concentrations of plutonium, americium, and uranium than the immediate surrounding soil. The type of mound does not appear to have influenced the amount of the radioactive material found in the mound except for the animal mounds where the burrowing activities appear to have obliterated distribution patterns

Community water fluoridation on the Internet and social media.

Science.gov (United States)

Mertz, Aaron; Allukian, Myron

2014-01-01

In the United States, 95 percent of teens and 85 percent of adults use the Internet. Two social media outlets, Facebook and Twitter, reach more than 150 billion users. This study describes anti-fluoridation activity and dominance on the Internet and social media, both of which are community water fluoridation (CWF) information sources. Monthly website traffic to major fluoridation websites was determined from June 2011 to May 2012. Facebook, Twitter, and YouTube fluoridation activity was categorized as "proCWF" or "anti-CWF." Twitter's anti-CWF tweets were further subcategorized by the argument used against CWF. Anti-CWF website traffic was found to exceed proCWF activity five- to sixty-fold. Searching "fluoride" and "fluoridation" on Facebook resulted in 88 to 100 percent anti-CWF groups and pages; "fluoridation" on Twitter and YouTube resulted in 64 percent anti-CWF tweets and 99 percent anti-CWF videos, respectively. "Cancer, " "useless, " and "poisonous" were the three major arguments used against fluoridation. Anti-fluoridation information significantly dominates the Internet and social media. Thousands of people are being misinformed daily about the safety, health, and economic benefits of fluoridation.

Americium-curium vitrification process development

International Nuclear Information System (INIS)

Fellinger, A.P.; Baich, M.A.; Hardy, B.J

1999-01-01

The successful demonstration of sequentially drying, calcining and vitrifying an oxalate slurry in the Drain Tube Test Stand (DTTS) vessel provided the process basis for testing on a larger scale in a cylindrical induction heated melter. A single processing issue, that of batch volume expansion, was encountered during the initial stage of testing. The increase in batch volume centered on a sintered frit cap and high temperature bubble formation. The formation of a sintered frit cap expansion was eliminated with the use of cullet. Volume expansions due to high temperature bubble formation (oxygen liberation from cerium reduction) were mitigated in the DTTS melter vessel through a vessel temperature profile that effectively separated the softening point of the glass cullet and the evolving oxygen from cerium reduction. An increased processing temperature of 1,470 C and a two hour hold time to find any remaining bubbles successfully reduced bubbles in the poured glass to an acceptable level. The success of the preliminary process demonstrations provided a workable process basis that was directly applicable to the newly installed Cylindrical Induction Melter (CIM) system, making the batch flowsheet the preferred option for vitrification of the americium-curium surrogate feed stream

Biomonitoring Equivalents for interpretation of urinary fluoride.

Science.gov (United States)

Aylward, L L; Hays, S M; Vezina, A; Deveau, M; St-Amand, A; Nong, A

2015-06-01

Exposure to fluoride is widespread due to its natural occurrence in the environment and addition to drinking water and dental products for the prevention of dental caries. The potential health risks of excess fluoride exposure include aesthetically unacceptable dental fluorosis (tooth mottling) and increased skeletal fragility. Numerous organizations have conducted risk assessments and set guidance values to represent maximum recommended exposure levels as well as recommended adequate intake levels based on potential public health benefits of fluoride exposure. Biomonitoring Equivalents (BEs) are estimates of the average biomarker concentrations corresponding to such exposure guidance values. The literature on daily urinary fluoride excretion rates as a function of daily fluoride exposure was reviewed and BE values corresponding to the available US and Canadian exposure guidance values were derived for fluoride in urine. The derived BE values range from 1.1 to 2.1mg/L (1.2-2.5μg/g creatinine). Concentrations of fluoride in single urinary spot samples from individuals, even under exposure conditions consistent with the exposure guidance values, may vary from the predicted average concentrations by several-fold due to within- and across-individual variation in urinary flow and creatinine excretion rates and due to the rapid elimination kinetics of fluoride. Thus, the BE values are most appropriately applied to screen population central tendency estimates for biomarker concentrations rather than interpretation of individual spot sample concentrations. Copyright © 2015. Published by Elsevier Inc.

FLUORIDE SORPTION USING MORRINGA INDICA-BASED ACTIVATED CARBON

Directory of Open Access Journals (Sweden)

G. Karthikeyan, S. Siva Ilango

2007-01-01

Full Text Available Batch adsorption experiments using activated carbon prepared from Morringa Indica bark were conducted to remove fluoride from aqueous solution. A minimum contact time of 25 min was required for optimum fluoride removal. The influence of adsorbent, dose, pH, co-ions (cations and anions on fluoride removal by the activated carbon has been experimentally verified. The adsorption of fluoride was studied at 30 C, 40 C and 50 C. The kinetics of adsorption and adsorption isotherms at different temperatures were studied. The fluoride adsorption obeyed both Langmuir and Freundlich isotherms and followed a pseudo first order kinetic model. The thermodynamic studies revealed that the fluoride adsorption by Morringa Indica is an endothermic process indicating an increase in sorption rate at higher temperatures. The negative values of G indicate the spontaneity of adsorption. SEM and XRD studies confirmed the surface morphological characteristics of the adsorbent and the deposition of fluoride on the surface of the material.

Effect of titanium tetrafluoride, amine fluoride and fluoride varnish on enamel erosion in vitro

NARCIS (Netherlands)

Vieira, A; Ruben, JL; Huysmans, MCDNJM

2005-01-01

This study aimed at evaluating the effect of 1 and 4% titanium tetrafluoride (TiF4) gels, amine fluoride (AmF) 1 and 0.25% and a fluoride varnish (FP) on the prevention of dental erosion. Two experimental groups served as controls, one with no pretreatment and another one pre-treated with a

Experimental and in situ investigations on americium, curium and plutonium behaviour in marine benthic species: transfer from water or sediments

International Nuclear Information System (INIS)

Miramand, P.

1984-06-01

The tranfer of transuranic elements -americium, curium and plutonium- from the sediments containing them to some marine benthic species (endofauna and epifauna) was studied with a twofold approach - laboratory and in-situ investigation. The experimental investigations, divided into three parts, made it possible to specify concentration factors (F.C.), transfer factors (F.T.) and to understand the process involved for 5 benthic species. The result were refined by an in-situ study that brought new data on the marine distribution of the transuranic elements released by the La Hague plant. Finally, the localization of americium and plutonium in the tissues and cells of these species was determined by autoradiography [fr

Accumulation of americium-241 in the biomass of aquatic plants of the Yenisei river: experimental study

International Nuclear Information System (INIS)

Zotina, T.A.; Bolsunovsky, A.Y.A.; Bondareva, L.G.

2004-01-01

Due to the operation of the Mining-and-Chemical Combine (Krasnoyarsk-26), which has been manufacturing weapons-grade plutonium for several decades, the Yenisei River is contaminated with transuranic elements (including 241 Am). 241 Am was found in the riverside soil, sediment and in the biomass of aquatic plants (Bolsunovsky et al., 1999, 2002). Aquatic plants are an important link in the migration of radionuclides in an aquatic ecosystem. In laboratory experiments, we investigated accumulation of 241 Am by the submerged macrophyte from the Yenisei River: the pond weed (Elodea canadensis) and the aquatic moss (Fontinalis antipyretica), and release of 241 Am from the biomass. The content of 241 Am was measured on a Canberra (USA) gamma-spectrometer. The experiments showed that specific accumulation and concentration factors of 241 Am in the plants were in inverse proportion to their biomass. We obtained new data on release of 241 Am from the biomass of macrophyte. Americium-241 was more firmly fixed in the biomass of the aquatic moss. In 12 months, the biomass of the aquatic moss released about 30% of the initial americium activity into the water. To compare, the biomass of the pond weed released into the water medium up to 64% of the initial 241 Am activity in 1.5 4 months. The release rate was dependent on the decomposition rate of the plant biomass. The experiments showed that submerged macrophyte of the Yenisei River can accumulate considerable activities of 241 Am and retain americium for long periods of time in biomass. (author)

Fluoride-induced disruption of reproductive hormones in men

International Nuclear Information System (INIS)

Ortiz-Perez, Deogracias; Rodriguez-Martinez, Manuel; Martinez, Flavio; Borja-Aburto, V.H.; Castelo, Julio; Grimaldo, J.I.; Cruz, Esperanza de la; Carrizales, Leticia; Diaz-Barriga, Fernando

2003-01-01

Fluoride-induced reproductive effects have been reported in experimental models and in humans. However, these effects were found in heavily exposed scenarios. Therefore, in this work our objective was to study reproductive parameters in a population exposed to fluoride at doses of 3-27 mg/day (high-fluoride-exposed group--HFEG). Urinary fluoride levels, semen parameters, and reproductive hormones in serum (LH, FSH, estradiol, prolactin, inhibin-B, free and total testosterone) were measured. Results were compared with a group of individuals exposed to fluoride at lower doses: 2-13 mg/day (low-fluoride-exposed group-LFEG). A significant increase in FSH (P<0.05) and a reduction of inhibin-B, free testosterone, and prolactin in serum (P<0.05) were noticed in the HFEG. When HFEG was compared to LFEG, a decreased sensitivity was found in the FSH response to inhibin-B (P<0.05). A significant negative partial correlation was observed between urinary fluoride and serum levels of inhibin-B (r=-0.333, P=0.028) in LFEG. Furthermore, a significant partial correlation was observed between a chronic exposure index for fluoride and the serum concentrations of inhibin-B (r=-0.163, P=0.037) in HFEG. No abnormalities were found in the semen parameters studied in the present work, neither in the HFEG, nor in the LFEG. The results obtained indicate that a fluoride exposure of 3-27 mg/day induces a subclinical reproductive effect that can be explained by a fluoride-induced toxic effect in both Sertoli cells and gonadotrophs

4-phenylbutyrate Mitigates Fluoride-Induced Cytotoxicity in ALC Cells

Directory of Open Access Journals (Sweden)

Maiko Suzuki

2017-05-01

Full Text Available Chronic fluoride over-exposure during pre-eruptive enamel development can cause dental fluorosis. Severe dental fluorosis is characterized by porous, soft enamel that is vulnerable to erosion and decay. The prevalence of dental fluorosis among the population in the USA, India and China is increasing. Other than avoiding excessive intake, treatments to prevent dental fluorosis remain unknown. We previously reported that high-dose fluoride induces endoplasmic reticulum (ER stress and oxidative stress in ameloblasts. Cell stress induces gene repression, mitochondrial damage and apoptosis. An aromatic fatty acid, 4-phenylbutyrate (4PBA is a chemical chaperone that interacts with misfolded proteins to prevent ER stress. We hypothesized that 4PBA ameliorates fluoride-induced ER stress in ameloblasts. To determine whether 4PBA protects ameloblasts from fluoride toxicity, we analyzed gene expression of Tgf-β1, Bcl2/Bax ratio and cytochrome-c release in vitro. In vivo, we measured fluorosis levels, enamel hardness and fluoride concentration. Fluoride treated Ameloblast-lineage cells (ALC had decreased Tgf-β1 expression and this was reversed by 4PBA treatment. The anti-apoptotic Blc2/Bax ratio was significantly increased in ALC cells treated with fluoride/4PBA compared to fluoride treatment alone. Fluoride treatment induced cytochrome-c release from mitochondria into the cytosol and this was inhibited by 4PBA treatment. These results suggest that 4PBA mitigates fluoride-induced gene suppression, apoptosis and mitochondrial damage in vitro. In vivo, C57BL/6J mice were provided fluoridated water for six weeks with either fluoride free control-chow or 4PBA-containing chow (7 g/kg 4PBA. With few exceptions, enamel microhardness, fluorosis levels, and fluoride concentrations of bone and urine did not differ significantly between fluoride treated animals fed with control-chow or 4PBA-chow. Although 4PBA mitigated high-dose fluoride toxicity in vitro, a diet

4-phenylbutyrate Mitigates Fluoride-Induced Cytotoxicity in ALC Cells.

Science.gov (United States)

Suzuki, Maiko; Everett, Eric T; Whitford, Gary M; Bartlett, John D

2017-01-01

Chronic fluoride over-exposure during pre-eruptive enamel development can cause dental fluorosis. Severe dental fluorosis is characterized by porous, soft enamel that is vulnerable to erosion and decay. The prevalence of dental fluorosis among the population in the USA, India and China is increasing. Other than avoiding excessive intake, treatments to prevent dental fluorosis remain unknown. We previously reported that high-dose fluoride induces endoplasmic reticulum (ER) stress and oxidative stress in ameloblasts. Cell stress induces gene repression, mitochondrial damage and apoptosis. An aromatic fatty acid, 4-phenylbutyrate (4PBA) is a chemical chaperone that interacts with misfolded proteins to prevent ER stress. We hypothesized that 4PBA ameliorates fluoride-induced ER stress in ameloblasts. To determine whether 4PBA protects ameloblasts from fluoride toxicity, we analyzed gene expression of Tgf -β 1, Bcl2 / Bax ratio and cytochrome-c release in vitro . In vivo , we measured fluorosis levels, enamel hardness and fluoride concentration. Fluoride treated Ameloblast-lineage cells (ALC) had decreased Tgf -β 1 expression and this was reversed by 4PBA treatment. The anti-apoptotic Blc2 / Bax ratio was significantly increased in ALC cells treated with fluoride/4PBA compared to fluoride treatment alone. Fluoride treatment induced cytochrome-c release from mitochondria into the cytosol and this was inhibited by 4PBA treatment. These results suggest that 4PBA mitigates fluoride-induced gene suppression, apoptosis and mitochondrial damage in vitro . In vivo , C57BL/6J mice were provided fluoridated water for six weeks with either fluoride free control-chow or 4PBA-containing chow (7 g/kg 4PBA). With few exceptions, enamel microhardness, fluorosis levels, and fluoride concentrations of bone and urine did not differ significantly between fluoride treated animals fed with control-chow or 4PBA-chow. Although 4PBA mitigated high-dose fluoride toxicity in vitro , a diet rich

Plutonium and americium in arctic waters, the North Sea and Scottish and Irish coastal zones

DEFF Research Database (Denmark)

Hallstadius, L.; Aarkrog, Asker; Dahlgaard, Henning

1986-01-01

Plutonium and americium have been measured in surface waters of the Greenland and Barents Seas and in the northern North Sea from 1980 through 1984. Measurements in water and biota, Fucus, Mytilus and Patella, were carried out in North-English and Scottish waters in 1982 and Fucus samples were co...

The behaviour under irradiation of molybdenum matrix for inert matrix fuel containing americium oxide (CerMet concept)

Energy Technology Data Exchange (ETDEWEB)

D' Agata, E., E-mail: elio.dagata@ec.europa.eu [European Commission, Joint Research Centre, Institute for Energy and Transport, P.O. Box 2, 1755 ZG Petten (Netherlands); Knol, S.; Fedorov, A.V. [Nuclear Research and Consultancy Group, P.O. Box 25, 1755 ZG Petten (Netherlands); Fernandez, A.; Somers, J. [European Commission, Joint Research Centre, Institute for Transuranium Elements, P.O. Box 2340, 76125 Karlsruhe (Germany); Klaassen, F. [Nuclear Research and Consultancy Group, P.O. Box 25, 1755 ZG Petten (Netherlands)

2015-10-15

Americium is a strong contributor to the long term radiotoxicity of high activity nuclear waste. Transmutation by irradiation in nuclear reactors or Accelerator Driven System (ADS, subcritical reactors dedicated to transmutation) of long-lived nuclides like {sup 241}Am is therefore an option for the reduction of radiotoxicity of waste packages to be stored in a repository. In order to safely burn americium in a fast reactor or ADS, it must be incorporated in a matrix that could be metallic (CerMet target) or ceramic (CerCer target). One of the most promising matrix to incorporate Am is molybdenum. In order to address the issues (swelling, stability under irradiation, gas retention and release) of using Mo as matrix to transmute Am, two irradiation experiments have been conducted recently at the High Flux Reactor (HFR) in Petten (The Netherland) namely HELIOS and BODEX. The BODEX experiment is a separate effect test, where the molybdenum behaviour is studied without the presence of fission products using {sup 10}B to “produce” helium, the HELIOS experiment included a more representative fuel target with the presence of Am and fission product. This paper covers the results of Post Irradiation Examination (PIE) of the two irradiation experiments mentioned above where molybdenum behaviour has been deeply investigated as possible matrix to transmute americium (CerMet fuel target). The behaviour of molybdenum looks satisfying at operating temperature but at high temperature (above 1000 °C) more investigation should be performed.

Chronic fluoride toxicity: dental fluorosis.

Science.gov (United States)

Denbesten, Pamela; Li, Wu

2011-01-01

Dental fluorosis occurs as a result of excess fluoride ingestion during tooth formation. Enamel fluorosis and primary dentin fluorosis can only occur when teeth are forming, and therefore fluoride exposure (as it relates to dental fluorosis) occurs during childhood. In the permanent dentition, this would begin with the lower incisors, which complete mineralization at approximately 2-3 years of age, and end after mineralization of the third molars. The white opaque appearance of fluorosed enamel is caused by a hypomineralized enamel subsurface. With more severe dental fluorosis, pitting and a loss of the enamel surface occurs, leading to secondary staining (appearing as a brown color). Many of the changes caused by fluoride are related to cell/matrix interactions as the teeth are forming. At the early maturation stage, the relative quantity of amelogenin protein is increased in fluorosed enamel in a dose-related manner. This appears to result from a delay in the removal of amelogenins as the enamel matures. In vitro, when fluoride is incorporated into the mineral, more protein binds to the forming mineral, and protein removal by proteinases is delayed. This suggests that altered protein/mineral interactions are in part responsible for retention of amelogenins and the resultant hypomineralization that occurs in fluorosed enamel. Fluoride also appears to enhance mineral precipitation in forming teeth, resulting in hypermineralized bands of enamel, which are then followed by hypomineralized bands. Enhanced mineral precipitation with local increases in matrix acidity may affect maturation stage ameloblast modulation, potentially explaining the dose-related decrease in cycles of ameloblast modulation from ruffle-ended to smooth-ended cells that occur with fluoride exposure in rodents. Specific cellular effects of fluoride have been implicated, but more research is needed to determine which of these changes are relevant to the formation of fluorosed teeth. As further

Health effects of fluoride pollution caused by coal burning

Energy Technology Data Exchange (ETDEWEB)

Ando, M.; Tadano, M.; Yamamoto, S.; Tamura, K.; Chen, X. [Regional Environment Division, National Institute for Environmental Studies, Tsukuba, 305-0083 Ibaraki (Japan); Asanuma, S. [Japan Institute of Rural Medicine, Usuda, Nagano (Japan); Watanabe, T. [Saku Central Hospital, Usuda, Nagano (Japan); Kondo, T. [Matsumoto Dental College, Shiojiri, Nagano (Japan); Sakurai, S. [Otsuma Women' s University, Tama, Tokyo (Japan); Ji, R.; Liang, C.; Cao, S. [Institute of Environmental Health and Engineering, Beijing (China); Hong, Z. [Shanxi Maternity and Children' s Hospital, Taiyuan (China)

2001-04-23

Recently a huge amount of fluoride in coal has been released into indoor environments by the combustion of coal and fluoride pollution seems to be increasing in some rural areas in China. Combustion of coal and coal bricks is the primary source of gaseous and aerosol fluoride and these forms of fluoride can easily enter exposed food products and the human respiratory tract. Major human fluoride exposure was caused by consumption of fluoride contaminated food, such as corn, chilies and potatoes. For each diagnostic syndrome of dental fluorosis, a log-normal distribution was observed on the logarithm of urinary fluoride concentration in students in China. Urinary fluoride content was found to be a primary health indicator of the prevalence of dental fluorosis in the community. In the fluorosis areas, osteosclerosis in skeletal fluorosis patients was observed with a high prevalence. A biochemical marker of bone resorption, urinary deoxypyridinoline content was much higher in residents in China than in residents in Japan. It was suggested that bone resorption was stimulated to a greater extent in residents in China and fluoride may stimulate both bone resorption and bone formation. Renal function especially glomerular filtration rate was very sensitive to fluoride exposure. Inorganic phosphate concentrations in urine were significantly lower in the residents in fluorosis areas in China than in non-fluorosis area in China and Japan. Since airborne fluoride from the combustion of coal pollutes extensively both the living environment and food, it is necessary to reduce fluoride pollution caused by coal burning.

Thermodynamic data-base for metal fluorides

Energy Technology Data Exchange (ETDEWEB)

Yoo, Jae Hyung; Lee, Byung Gik; Kang, Young Ho and others

2001-05-01

This study is aimed at collecting useful data of thermodynamic properties of various metal fluorides. Many thermodynamic data for metal fluorides are needed for the effective development, but no report of data-base was published. Accordingly, the objective of this report is to rearrange systematically the existing thermodynamic data based on metal fluorides and is to use it as basic data for the development of pyrochemical process. The physicochemical properties of various metal fluorides and metals were collected from literature and such existing data base as HSC code, TAPP code, FACT code, JANAF table, NEA data-base, CRC handbook. As major contents of the thermodynamic data-base, the physicochemical properties such as formation energy, viscosity, density, vapor pressure, etc. were collected. Especially, some phase diagrams of eutectic molten fluorides are plotted and thermodynamic data of liquid metals are also compiled. In the future, the technical report is to be used as basic data for the development of the pyrochemical process which is being carried out as a long-term nuclear R and D project.

Thermodynamic data-base for metal fluorides

International Nuclear Information System (INIS)

Yoo, Jae Hyung; Lee, Byung Gik; Kang, Young Ho and others

2001-05-01

This study is aimed at collecting useful data of thermodynamic properties of various metal fluorides. Many thermodynamic data for metal fluorides are needed for the effective development, but no report of data-base was published. Accordingly, the objective of this report is to rearrange systematically the existing thermodynamic data based on metal fluorides and is to use it as basic data for the development of pyrochemical process. The physicochemical properties of various metal fluorides and metals were collected from literature and such existing data base as HSC code, TAPP code, FACT code, JANAF table, NEA data-base, CRC handbook. As major contents of the thermodynamic data-base, the physicochemical properties such as formation energy, viscosity, density, vapor pressure, etc. were collected. Especially, some phase diagrams of eutectic molten fluorides are plotted and thermodynamic data of liquid metals are also compiled. In the future, the technical report is to be used as basic data for the development of the pyrochemical process which is being carried out as a long-term nuclear R and D project

Metal fluoride complexes of Na,K-ATPase: characterization of fluoride-stabilized phosphoenzyme analogues and their interaction with cardiotonic steroids.

Science.gov (United States)

Cornelius, Flemming; Mahmmoud, Yasser A; Toyoshima, Chikashi

2011-08-26

The Na,K-ATPase belongs to the P-type ATPase family of primary active cation pumps. Metal fluorides like magnesium-, beryllium-, and aluminum fluoride act as phosphate analogues and inhibit P-type ATPases by interacting with the phosphorylation site, stabilizing conformations that are analogous to specific phosphoenzyme intermediates. Cardiotonic steroids like ouabain used in the treatment of congestive heart failure and arrhythmias specifically inhibit the Na,K-ATPase, and the detailed structure of the highly conserved binding site has recently been described by the crystal structure of the shark Na,K-ATPase in a state analogous to E2·2K(+)·P(i) with ouabain bound with apparently low affinity (1). In the present work inhibition, and subsequent reactivation by high Na(+), after treatment of shark Na,K-ATPase with various metal fluorides are characterized. Half-maximal inhibition of Na,K-ATPase activity by metal fluorides is in the micromolar range. The binding of cardiotonic steroids to the metal fluoride-stabilized enzyme forms was investigated using the fluorescent ouabain derivative 9-anthroyl ouabain and compared with binding to phosphorylated enzyme. The fastest binding was to the Be-fluoride stabilized enzyme suggesting a preformed ouabain binding cavity, in accord with results for Ca-ATPase where Be-fluoride stabilizes the E2-P ground state with an open luminal ion access pathway, which in Na,K-ATPase could be a passage for ouabain. The Be-fluoride stabilized enzyme conformation closely resembles the E2-P ground state according to proteinase K cleavage. Ouabain, but not its aglycone ouabagenin, prevented reactivation of this metal fluoride form by high Na(+) demonstrating the pivotal role of the sugar moiety in closing the extracellular cation pathway.

Molten fluoride fuel salt chemistry

International Nuclear Information System (INIS)

Toth, L.M.; Del Cul, G.D.; Dai, S.; Metcalf, D.H.

1995-01-01

The chemistry of molten fluorides is traced from their development as fuels in the Molten Salt Reactor Experiment with important factors in their selection being discussed. Key chemical characteristics such as solubility, redox behavior, and chemical activity are explained as they relate to the behavior of molten fluoride fuel systems. Development requirements for fitting the current state of the chemistry to modern nuclear fuel system are described. It is concluded that while much is known about molten fluoride behavior which can be used effectively to reduce the amount of development required for future systems, some significant molten salt chemical questions must still be addressed. copyright American Institute of Physics 1995

Milk fluoridation for the prevention of dental caries

Directory of Open Access Journals (Sweden)

Jolán Bánóczy

2013-11-01

Full Text Available The aim of this review is to give an overview of 55 years experience of milk fluoridation and draw conclusions about the applicability of the method. Fluoridated milk was first investigated in the early 1950s, almost simultaneously in Switzerland, the USA and Japan. Stimulated by the favourable results obtained from these early studies, the establishment of The Borrow Dental Milk Foundation (subsequently The Borrow Foundation in England gave an excellent opportunity for further research, both clinical and non-clinical, and a productive collaboration with the World Health Organization which began in the early 1980s. Numerous peer-reviewed publications in international journals showed clearly the bioavailability of fluoride in various types of milk. Clinical trials were initiated in the 1980s – some of these can be classed as randomised controlled trials, while most of the clinical studies were community preventive programmes. Conclusion. These evaluations showed clearly that the optimal daily intake of fluoride in milk is effective in preventing dental caries. The amount of fluoride added to milk depends on background fluoride exposure and age of the children: commonly in the range 0.5 to 1.0 mg per day. An advantage of the method is that a precise amount of fluoride can be delivered under controlled conditions. The cost of milk fluoridation programmes is low, about € 2 to 3 per child per year. Fluoridation of milk can be recommended as a caries preventive measure where the fluoride concentration in drinking water is suboptimal, caries experience in children is significant, and there is an existing school milk programme.

Milk fluoridation for the prevention of dental caries.

Science.gov (United States)

Bánóczy, Jolán; Rugg-Gunn, Andrew; Woodward, Margaret

2013-11-01

The aim of this review is to give an overview of 55 years experience of milk fluoridation and draw conclusions about the applicability of the method. Fluoridated milk was first investigated in the early 1950s, almost simultaneously in Switzerland, the USA and Japan. Stimulated by the favourable results obtained from these early studies, the establishment of The Borrow Dental Milk Foundation (subsequently The Borrow Foundation) in England gave an excellent opportunity for further research, both clinical and non-clinical, and a productive collaboration with the World Health Organization which began in the early 1980s. Numerous peer-reviewed publications in international journals showed clearly the bioavailability of fluoride in various types of milk. Clinical trials were initiated in the 1980s - some of these can be classed as randomised controlled trials, while most of the clinical studies were community preventive programmes. These evaluations showed clearly that the optimal daily intake of fluoride in milk is effective in preventing dental caries. The amount of fluoride added to milk depends on background fluoride exposure and age of the children: commonly in the range 0.5 to 1.0 mg per day. An advantage of the method is that a precise amount of fluoride can be delivered under controlled conditions. The cost of milk fluoridation programmes is low, about € 2 to 3 per child per year. Fluoridation of milk can be recommended as a caries preventive measure where the fluoride concentration in drinking water is suboptimal, caries experience in children is significant, and there is an existing school milk programme. Copyright © 2013 by Academy of Sciences and Arts of Bosnia and Herzegovina.

Poisoning by coal smoke containing arsenic and fluoride

Energy Technology Data Exchange (ETDEWEB)

An, D.; He, Y.G.; Hu, Q.X. [Guizhou Sanitary and Epidemiological Station, Guiyang (China)

1997-02-01

An investigation was made into a disease involving skin pigmentation, keratosis of the hands and feet, dental discoloration, and generalized bone and joint pain, stiffness and rigidity, in the village of Bazhi, Zhijin County, Ghizhou Province, People`s Republic of China. Measurements were made of the arsenic and fluoride levels of coal, water, air, food, urine and hair in Bazhi and a control village, Xinzhai, in which coal with a low arsenic content was used. Up to 188 people, including children, in Bazhi and 752 in Xinzhai, were examined for the presence of chronic arsenium, skeletal fluorosis, dental fluorosis and electrocardiogram abnormalities. The coal in Bazhi was found to contain high levels of arsenic and fluoride resulting, after burning in homes without an adequate chimney systems, in pollution of air and food with arsenic and fluoride. The coal in Xinzhai did not cause arsenic pollution but did produce a higher level of fluoride pollution. It was concluded that the endemic disease in Bazhi was caused by pollution by coal smoke containing arsenic and fluoride. It is suggested that arsenic may act synergistically with fluoride so that a lower level of fluoride may produce fluoride toxicity with dental and skeletal fluorosis.

New Insight on the Response of Bacteria to Fluoride

Science.gov (United States)

Breaker, R.R.

2012-01-01

Fluoride has been used for decades to prevent caries and it is well established that this anion can inhibit the growth of bacteria. However, the precise effects that fluoride has on bacteria and the mechanisms that bacteria use to overcome fluoride toxicity have largely remained unexplored. Recently, my laboratory reported the discovery of biological systems that bacteria use to sense fluoride and reduce fluoride toxicity. These sensors and their associated genes are very widespread in biology, which has implications for a number of issues that are central to the use of fluoride for dental care. Below I provide a summary of our findings, comment on some of the key prospects for expanding our understanding of fluoride's effects on biology, and propose some future uses of this knowledge. PMID:22327376

New insight on the response of bacteria to fluoride.

Science.gov (United States)

Breaker, R R

2012-01-01

Fluoride has been used for decades to prevent caries and it is well established that this anion can inhibit the growth of bacteria. However, the precise effects that fluoride has on bacteria and the mechanisms that bacteria use to overcome fluoride toxicity have largely remained unexplored. Recently, my laboratory reported the discovery of biological systems that bacteria use to sense fluoride and reduce fluoride toxicity. These sensors and their associated genes are very widespread in biology, which has implications for a number of issues that are central to the use of fluoride for dental care. Below I provide a summary of our findings, comment on some of the key prospects for expanding our understanding of fluoride's effects on biology, and propose some future uses of this knowledge. Copyright © 2012 S. Karger AG, Basel.

Bone fluoride determination for clinical investigation of osteoporosis

International Nuclear Information System (INIS)

Krishnan, S.S.; McNeill, K.G.; Hitchman, A.J.W.; Mernagh, J.R.; Lin, S.C.; Harrison, J.E.

1984-01-01

Sodium fluoride is the therapeutic agent known to stimulate bone growth with net increase in bone mineral mass in patients afflicted with osteoporosis, a common crippling bone disease. In order to study the effect of sodium fluoride treatment, a method of analysis for fluoride in bone has been developed using Neutron Activation Analysis (NAA). The technique proved to be simple, fast, reliable and non-destructive. Thus the sample, often bone biopsy specimen, is available, after fluoride analysis, for further histological studies. NAA was used to analyze both fluoride and calcium in the bone and the results expressed as F/Ca ratio was meaningful since it normalizes the fluoride to bone mineral mass which is the important factor in this study. Four years of fluoride treatment of osteoporotics showed significant increase of bone mass (up to 30%) in several patients. These increases were associated with histological bone picture of fluorosis. In the case of patients with renal osteodystrophy, there was evidence that fluorosis contributes to the bone disease. 3 references, 2 figures, 2 tables

Solubility and fluoride release in ionomers and compomers.

Science.gov (United States)

Bertacchini, S M; Abate, P F; Blank, A; Baglieto, M F; Macchi, R L

1999-03-01

The degree of solubility and the fluoride release of glass-ionomer cements and "compomers" were determined as a function of time. Three conventional glass-ionomer cements, three hybrid ionomers, and two compomers were included in the study. Disk-shaped specimens were prepared and immersed in a lactic acid solution. Solubility was evaluated from determinations of loss of mass as a function of time. To evaluate fluoride release, similar specimens were immersed in 50 mL of deionized water to which 50 mL of buffer solution was added. A fluoride ion detector was used to read the concentration of fluoride ion in the overall solution at different times after immersion. Material and time factors had a significant influence on results. The compomers showed less corrosion and fluoride release than the ionomers. Some correlation was found between solubility and fluoride leakage values. Components of both the ionomers and compomers that were studied can dissolve in water. The materials leak fluoride ions in amounts that differ according to the characteristics of the individual products.

Sustainable approach for recycling waste lamb and chicken bones for fluoride removal from water followed by reusing fluoride-bearing waste in concrete.

Science.gov (United States)

Ismail, Zainab Z; AbdelKareem, Hala N

2015-11-01

Sustainable management of waste materials is an attractive approach for modern societies. In this study, recycling of raw waste lamb and chicken bones for defluoridation of water has been estimated. The effects of several experimental parameters including contact time, pH, bone dose, fluoride initial concentration, bone grains size, agitation rate, and the effect of co-existing anions in actual samples of wastewater were studied for fluoride removal from aqueous solutions. Results indicated excellent fluoride removal efficiency up to 99.4% and 99.8% using lamb and chicken bones, respectively at fluoride initial concentration of 10 mg F/L and 120 min contact time. Maximum fluoride uptake was obtained at neutral pH range 6-7. Fluoride removal kinetic was well described by the pseudo-second order kinetic model. Both, Langmuir and Freundlich isotherm models could fit the experimental data well with correlation coefficient values >0.99 suggesting favorable conditions of the process. Furthermore, for complete sustainable management of waste bones, the resulted fluoride-bearing sludge was reused in concrete mixes to partially replace sand. Tests of the mechanical properties of fluoride sludge-modified concrete mixes indicated a potential environmentally friendly approach to dispose fluoride sludge in concrete and simultaneously enhance concrete properties. Copyright © 2015 Elsevier Ltd. All rights reserved.

New Insight on the Response of Bacteria to Fluoride

OpenAIRE

Breaker, R.R.

2012-01-01

Fluoride has been used for decades to prevent caries and it is well established that this anion can inhibit the growth of bacteria. However, the precise effects that fluoride has on bacteria and the mechanisms that bacteria use to overcome fluoride toxicity have largely remained unexplored. Recently, my laboratory reported the discovery of biological systems that bacteria use to sense fluoride and reduce fluoride toxicity. These sensors and their associated genes are very widespread in biolog...

Explosion of cation exchange column in americium recovery service, Hanford plant, August 30, 1976

International Nuclear Information System (INIS)

1976-01-01

This document is a collection of thirty references related to the explosion of the cation exchange column in the Americium Recovery Service of the Hanford Atomic Products Operation, Richland, Washington, on August 30, 1976. Some of the documents are related to the design and safety studies, while others refer to the accident and resulting decontamination efforts, investigations, and legal consequences

Widespread genetic switches and toxicity resistance proteins for fluoride.

Science.gov (United States)

Baker, Jenny L; Sudarsan, Narasimhan; Weinberg, Zasha; Roth, Adam; Stockbridge, Randy B; Breaker, Ronald R

2012-01-13

Most riboswitches are metabolite-binding RNA structures located in bacterial messenger RNAs where they control gene expression. We have discovered a riboswitch class in many bacterial and archaeal species whose members are selectively triggered by fluoride but reject other small anions, including chloride. These fluoride riboswitches activate expression of genes that encode putative fluoride transporters, enzymes that are known to be inhibited by fluoride, and additional proteins of unknown function. Our findings indicate that most organisms are naturally exposed to toxic levels of fluoride and that many species use fluoride-sensing RNAs to control the expression of proteins that alleviate the deleterious effects of this anion.

Recovery of americium from slag and crucible wastes and its purification

International Nuclear Information System (INIS)

Michael, K.M.; Dabholkar, G.M.; Vijayan, K.; Ramamoorthy, N.; Narayanan, C.V.; Jambunathan, U.; Kapoor, S.C.

1990-01-01

A method of recovery and purification of americium-241 from slag waste streams is described. Extraction of Am from slag solution of 0.16 M HNO 3 was carried out by tri-n-butyl phosphate. After stripping with acetic acid, Am was precipitated at pH 1. This was followed by metathesis to remove Ca. Final separation of Pu from Am solution was achieved by anion exchange method using Dowex 1x4 anion exchange resin. Details of large scale recovery of Am from slag are also described. (author). 12 refs., 11 tabs., 1 fig

Effects of different amine fluoride concentrations on enamel remineralization.

Science.gov (United States)

Naumova, E A; Niemann, N; Aretz, L; Arnold, W H

2012-09-01

The aim of this study was to investigate the effects of decreasing fluoride concentrations on repeated demineralizing challenges on human enamel. In 24 teeth, 3mm×3mm windows were prepared on the buccal and lingual sides and treated in a cycling demineralization-remineralization model. Remineralization was achieved with 100, 10 and 0.1 ppm fluoride from anime fluoride. Coronal sections were cut through the artificial lesions, and three sections per tooth were investigated using polarized light microscopy and scanning electron microscopy with quantitative element analysis. The morphology of the lesions was studied, and the extensions of the superficial layer and the body of the lesion were measured. Using element analysis, the Ca, P and F content were determined. The body of the lesion appeared remineralized after application of 100 ppm fluoride, while remineralization of the lesion was less successful after application of 10 and 0.1 ppm fluoride. The thickness of the superficial layer increased with decreasing fluoride concentrations, and also the extension of the body of the lesion increased. Ca and P content increased with increasing fluoride concentrations. The effectiveness of fluoride in enamel remineralization increased with increasing fluoride concentration. A consistently higher level of fluoride in saliva should be a goal in caries prevention. Copyright © 2012 Elsevier Ltd. All rights reserved.

Risk perception, psychological heuristics and the water fluoridation controversy.

Science.gov (United States)

Perrella, Andrea M L; Kiss, Simon J

2015-04-29

Increasingly, support for water fluoridation has come under attack. We seek an explanation, focusing on the case of Waterloo, Ontario, where a 2010 referendum overturned its water fluoridation program. In particular, we test whether individuals perceive the risks of water fluoridation based not on 'hard' scientific evidence but on heuristics and cultural norms. A sample of 376 residents in Waterloo were surveyed in June 2012 using random digit dialing. We use factor analysis, OLS regression, as well as t-tests to evaluate a survey experiment to test the credibility hypothesis. Perceptions of fluoride as a risk are lower among those who perceive fluoride's benefits (B = .473, p < 0.001) and those whose cultural view is 'egalitarian' (B = .156, p < 0.05). The experiment shows a lower level of perception of fluoride's benefits among respondents who are told that water fluoridation is opposed by a national advocacy group (Group A) compared to those who are told that the government and the World Health Organization support fluoridation (Group B) (t = 1.6547, p < 0.05), as well as compared to the control group (t = 1.8913, p < 0.05). There is no difference between Group B and the control, possibly because people's already general support for fluoridation is less prone to change when told that other public organizations also support fluoridation. Public health officials should take into account cultural norms and perceptions when individuals in a community appear to rise up against water fluoridation, with implications for other public health controversies.

Antibacterial Effect of Silver Diamine Fluoride on Cariogenic Organisms.

Science.gov (United States)

Lou, Yali; Darvell, Brain W; Botelho, Michael G

2018-05-01

To screen the possible antimicrobial activity of a range of clinically used, silver-based compounds on cariogenic organisms: silver diamine fluoride (SDF), silver fluoride, and silver nitrate. Preliminary screening disk-diffusion susceptibility tests were conducted on Mueller-Hinton agar plates inoculated with Streptococcus mutans, Lactobacillus acidophilus, and Actinomyces naeslundii, organisms known to be cariogenic. In order to identify which component of the silver compounds was responsible for any antibacterial (AB) effect, and to provide controls, the following were also investigated at high and low concentrations: sodium fluoride, ammonium fluoride, ammonium chloride, sodium fluoride, sodium chloride, and sodium nitrate, as well as deionized water as control. A volume of 10 pL of a test solution was dispensed onto a paper disk resting on the inoculated agar surface, and the plate incubated anaerobically at 37°C for 48 hours. The zones of inhibition were then measured. Silver diamine fluoride, silver fluoride, silver nitrate, and ammonium fluoride had significant AB effect (p effect at low concentration; the remaining other compounds had no effect. Silver ions appear to be the principal AB agent at both high and low concentration; fluoride ions only have an AB effect at high concentration, while ammonium, nitrate, chloride and sodium ions have none. The anticaries effect of topical silver solutions appears restricted to that of the silver ions. Silver compounds, such as SDF, silver fluoride, and silver nitrate have AB effect against cariogenic organisms and these may have clinical impact in arresting or preventing dental decay. Sodium fluoride did not have AB effect under the conditions tested.

Possibility of obtaining enriched americium-242g by the elution of recoil atoms from zeolite

Energy Technology Data Exchange (ETDEWEB)

Shafiev, A I; Vityutnev, V M; Ivanov, V M; Yakovlev, G N

1974-12-31

On the example of production the possibility of obtaining enriched actinide isotopes by the elution of recotl atoms with the use of a zeolite- americium-241 target was shown. The enrichment factor and the recoil atoms of / sup 242g/Am yield depend on preliminary target treatment and solution composition used for elution. (auth)

High Fluoride Dentifrices for Elderly and Vulnerable Adults

DEFF Research Database (Denmark)

Ekstrand, Kim Rud

2016-01-01

The primary aim of this work is to present the available evidence that toothpastes containing >1,500 ppm fluoride (2,500-2,800 and 5,000 ppm F) provide an additional caries preventive effect on root caries lesions in elderly patients compared to traditional dentifrices (1,000-1,450 ppm F......). The secondary aim of this paper is to discuss why high fluoride dentifrices in general should perform better than traditional F-containing toothpaste. When examining the few studies that have considered the preventive benefits of high fluoride products on root caries the relative risk appears to be around 0.......5, and the risk can thus be halved by exchanging traditional F-containing toothpaste for toothpaste containing 5,000 ppm F. There is reasonable evidence that high fluoride dentifrices significantly increase the fluoride concentration in saliva during the day and the fluoride concentration in plaque compared...

Approaches to the accurate characterization of high purity metal fluorides and fluoride glasses

Science.gov (United States)

Beary, E. S.; Paulsen, P. J.; Rains, T. C.; Ewing, K. J.; Jaganathan, J.; Aggarwal, I.

1990-11-01

The analytical challenges posed by the measurement of trace contaminants in high purity metal fluorides require that innovative chemical preparation procedures be used to enhance existing instrumental techniques. The instrumental techniques used to analyze these difficult matrices must be sensitive enough to detect extremely low levels of trace impurities, and the background interferences derived from the matrix (metal fluoride or glass) must be minimized. A survey of analytical techniques that have the necessary characteristics to analyze these materials will be given. In addition, means of controlling the chemical blank will be presented. Mass and atomic spectrometric techniques will be discussed, specifically graphite furnace atomic absorption spectrometry (GFAAS) and inductively coupled plasma-mass spectrometry (ICP-MS). Analytical procedures using GFAAS and ICP-MS have been developed to determine sub ppb (part per billion) levels of contaminants in high purity fluoride materials.

Fuel cycle covariance of plutonium and americium separations to repository capacity using information theoretic measures

International Nuclear Information System (INIS)

Scopatz, Anthony; Schneider, Erich; Li, Jun; Yim, Man-Sung

2011-01-01

A light water reactor, fast reactor symbiotic fuel cycle scenario was modeled and parameterized based on thirty independent inputs. Simultaneously and stochastically choosing different values for each of these inputs and performing the associated fuel cycle mass-balance calculation, the fuel cycle itself underwent Monte Carlo simulation. A novel information theoretic metric is postulated as a measure of system-wide covariance. This metric is the coefficient of variation of the set of uncertainty coefficients generated from 2D slices of a 3D contingency table. It is then applied to the fuel cycle, taking fast reactor used fuel plutonium and americium separations as independent variables and the capacity of a fully-loaded tuff repository as the response. This set of parameters is known from prior studies to have a strong covariance. When measured with all 435 other input parameters possible, the fast reactor plutonium and americium separations pair was found to be ranked the second most covariant. This verifies that the coefficient of variation metric captures the desired sensitivity of sensitivity effects in the nuclear fuel cycle. (author)

Influence of biofilms on migration of uranium, americium and europium in the environment; Einfluss von Biofilmen auf das Migrationsverhalten von Uran, Americium und Europium in der Umwelt

Energy Technology Data Exchange (ETDEWEB)

Baumann, Nils; Zirnstein, Isabel; Arnold, Thuro

2015-07-01

The report on the influence of biofilms on migration of uranium, americium and europium in the environment deals with the contamination problems of uranium mines such as SDAG WISMUT in Saxonia and Thuringia. In mine waters microorganisms form a complex microbiological biocoenosis in spite of low pH values and high heavy metal concentrations including high uranium concentrations. The analyses used microbiological methods like confocal laser scanning microscopy and molecular-biological techniques. The interactions of microorganism with fluorescent radioactive heavy metal ions were performed with TRLFS (time resolved laser-induced fluorescence spectroscopy).

Accumulation of americium-241 in the biomass of aquatic plants of the Yenisei river: experimental study

Energy Technology Data Exchange (ETDEWEB)

Zotina, T.A.; Bolsunovsky, A.Y.A.; Bondareva, L.G. [Institute of Biophysics SB RAS, Akademgorodok, Krasnoyarsk (Russian Federation)

2004-07-01

Due to the operation of the Mining-and-Chemical Combine (Krasnoyarsk-26), which has been manufacturing weapons-grade plutonium for several decades, the Yenisei River is contaminated with transuranic elements (including {sup 241}Am). {sup 241}Am was found in the riverside soil, sediment and in the biomass of aquatic plants (Bolsunovsky et al., 1999, 2002). Aquatic plants are an important link in the migration of radionuclides in an aquatic ecosystem. In laboratory experiments, we investigated accumulation of {sup 241}Am by the submerged macrophyte from the Yenisei River: the pond weed (Elodea canadensis) and the aquatic moss (Fontinalis antipyretica), and release of {sup 241}Am from the biomass. The content of {sup 241}Am was measured on a Canberra (USA) gamma-spectrometer. The experiments showed that specific accumulation and concentration factors of {sup 241}Am in the plants were in inverse proportion to their biomass. We obtained new data on release of {sup 241}Am from the biomass of macrophyte. Americium-241 was more firmly fixed in the biomass of the aquatic moss. In 12 months, the biomass of the aquatic moss released about 30% of the initial americium activity into the water. To compare, the biomass of the pond weed released into the water medium up to 64% of the initial {sup 241}Am activity in 1.5 4 months. The release rate was dependent on the decomposition rate of the plant biomass. The experiments showed that submerged macrophyte of the Yenisei River can accumulate considerable activities of {sup 241}Am and retain americium for long periods of time in biomass. (author)

Adsorption and exhaustion device for gaseoue uranium fluorides

International Nuclear Information System (INIS)

Kida, Yasuo; Nakamura, Yuichi.

1984-01-01

Purpose: To prevent gaseous uranium fluorides from passing through the adsorption layer upon exhausting the gaseous uranium, fluorides from a uranium fluoride processing facility through adsorption traps, by controlling the flow rate of the gaseous uranium fluorides passing through the layer constant. Constitution: An adsorption trap is connected by way of pipeways to a uranium fluoride processing facility, and a flow rate detector for detecting the flow rate of gaseous uranium fluorides and a pressure gauge for detecting the pressure at the inlet of the adsorption trap are disposed to the pipeways. The setting value for the pressure control is calculated from the detection value of the flow rate detector by the pressure control gage. Then, an operation amount for the pressure control valve is calculated based on the deviatoin between the setting value for the pressure control and the inlet pressure at the adsorption trap. This enables to control the flow rate of the gaseous uranium fluorides passing through the adsorption layer always constant thereby enabling to prevent excess increase in the flow rate which results in damages in the adsorption layer. (Moriyama, K.)

The effective use of fluorides in public health

DEFF Research Database (Denmark)

Jones, Sheila; Burt, Brian A; Petersen, Poul Erik

2005-01-01

, systematic reviews summarizing these extensive databases have indicated that water fluoridation and fluoride toothpastes both substantially reduce the prevalence and incidence of dental caries. We present four case studies that illustrate the use of fluoride in modern public health practice, focusing on......Dental caries remain a public health problem for many developing countries and for underprivileged populations in developed countries. This paper outlines the historical development of public health approaches to the use of fluoride and comments on their effectiveness. Early research...

Absorption, distribution and excretion of inhaled hydrogen fluoride in the rat

Energy Technology Data Exchange (ETDEWEB)

Morris, J.B.

1979-01-01

Rats were subjected to whole body HF exposure for 6 hrs or to nose-only HF exposure for 1 hr. Total and/or ionic fluoride concentrations in selected tissues were determined at various times following exposure. In rats sacrificed 6 hrs after whole body exposure, dose-dependent increases in lung, plasma, and kidney total and ionic fluoride concentration occurred. Rats excreted more fluoride in the urine after whole body exposure than could be explained by the amount of HF inhaled. Considerable evidence suggests that airborne HF deposits on fur and is then ingested due to preening activity. Urinary fluoride excretion was increased by nose-only exposure. The urinary fluoride excretion accounted for approximately twice the fluoride estimated to be inhaled during exposure. Tissue fluoride concentrations were elevated immediately after nose-only exposure. Fluoride concentrations in lung and kidney returned to control levels within 12 hrs. Plasma fluoride concentration was slightly elevated 24 hrs after the start of the 1 hr exposure but was at control levels at 96 hrs. Immediately following nose-only exposure, lung ionic fluoride concentrations were less than plasma ionic fluoride concentrations suggesting that the fluoride in the lung had reached that site via plasma transport rather than by inhalation. A dose-dependent increase in plasma ionic fluoride concentration occurred after upper respiratory tract HF exposure providing strong evidence that fluoride is absorbed systemically from that site. The plasma ionic fluoride concentration after upper respiratory tract exposure was of sufficient magnitude to account for the plasma fluoride concentrations observed in intact nose-only exposed rats. (ERB)

Fluoride release and recharge behavior of a nano-filled resin-modified glass ionomer compared with that of other fluoride releasing materials.

Science.gov (United States)

Mitra, Sumita B; Oxman, Joe D; Falsafi, Afshin; Ton, Tiffany T

2011-12-01

To compare the long-term fluoride release kinetics of a novel nano-filled two-paste resin-modified glass-ionomer (RMGI), Ketac Nano (KN) with that of two powder-liquid resin-modified glass-ionomers, Fuji II LC (FLC) and Vitremer (VT) and one conventional glass-ionomer, Fuji IX (FIX). Fluoride release was measured in vitro using ion-selective electrodes. Kinetic analysis was done using regression analysis and compared with existing models for GIs and compomers. In a separate experiment the samples of KN and two conventional glass-ionomers, FIX and Ketac Molar (KM) were subjected to a treatment with external fluoride source (Oral-B Neutra-Foam) after 3 months of fluoride release and the recharge behavior studied for an additional 7-day period. The cumulative amount of fluoride released from KN, VT and FLC and the release profiles were statistically similar but greater than that for FIX at P coating of KN with its primer and of DY with its adhesive did not significantly alter the fluoride release behavior of the respective materials. The overall rate for KN was significantly higher than for the compomer DY. DY showed a linear rate of release vs. t and no burst effect as expected for compomers. The nanoionomer KN showed fluoride recharge behavior similar to the conventional glass ionomers FIX and KM. Thus, it was concluded that the new RMGI KN exhibits fluoride ion release behavior similar to typical conventional and RMGIs and that the primer does not impede the release of fluoride.

Fluoridation Basics

Science.gov (United States)

... return on investment for community water fluoridation (including productivity losses) ranged from $4 in small communities of ... National Center for Chronic Disease Prevention and Health Promotion Email Recommend Tweet YouTube Instagram Listen Watch RSS ...

Citric complexes, neodymium citrate and americium citrate

International Nuclear Information System (INIS)

Bouhlassa, Saidati.

1981-06-01

The behaviour of neodymium and americium has been studied in citric aqueous medium by two methods: solvent extraction of elements at tracer scale as chelates and by potentiometry. So range of pH and concentrations of elements and citric acid never reached before have been explored: 10 -7 -1 M, 10 -10 -3 , Csub(H3 Cit) -1 M, 1 2 O; AmCit, xH 2 O; NdCit 2 Co(NH 3 ) 6 , 8H 2 O; AmCit 2 Co(NH 3 ) 6 , xH 2 O and Nd 3 (OH) 4 (Cit) 4 NH 4 (Co(NH 3 ) 6 ) 2 , 18H 2 O. Their spectroscopic and crystallographic characteristics have been listed and studied. The nephelauxetic effect has been estimated from citric complexes as well as from citrates of these elements. The structure of the complexes in solution has been discussed on the basis of analysis of hypersensitive transition in different complexes [fr

Fluoride removal performance of phosphoric acid treated lime ...

African Journals Online (AJOL)

Fluoride in drinking water above permissible levels is responsible for dental and skeletal fluorosis. In this study, removal of fluoride ions from water using phosphoric acid treated lime was investigated in continuous and point-of-use system operations. In the continuous column operations, fluoride removal performance was ...

An experimental study of americium-241 biokinetics in the Lobster Homarus Gammarus. Analysis of the accumulation/storage and detoxification processes at the subcellular level; Etude experimentale des biocinetiques de l`americium-241 chez le homard homarus gammarus. Analyse des mecanismes d`accumulation et de detoxication au niveau subcellulaire

Energy Technology Data Exchange (ETDEWEB)

Paquet, F

1993-01-01

An experimental study of americium-241 kinetics has been conducted in the lobster Homarus gammmarus. The investigations were conducted at all the levels from the whole body to the subcellular and molecular levels. The animals were contaminated by a single or chronic ingestion of {sup 241} Am labelled mussels. Assessments of accumulation, elimination and distribution of the radionuclide were established on organisms kept in the laboratory; they made it possible to demonstrate the importance of the digestive gland in the radionuclide transfer pathways. The preliminary results led to structural then ultrastructural investigations of the digestive gland in association with radioautographic studies and cellular extractions methods. Four cellular types were demonstrated, only two of them being implied in the radionuclide retention, the former being responsible for americium intake and the latter for its long-term retention. By means of biochemical techniques, subcellular accumulation was studied and the organelles implied in the nuclide retention were specified. Finally, a method of cellular nuclei dissociation was developed; it made it possible to analyse the molecular nature of americium ligands and to demonstrate the function of the protein nuclear matrix in the nuclide retention.

Fluoride uptake from restorative dental materials by human enamel

International Nuclear Information System (INIS)

Forsten, L.; Rytoemaa, I.; Anttila, A.; Keinonen, J.

1976-01-01

The purpose of the study was to determine the uptake in vitro of fluoride from restorative materials by tooth enamel and whether prior etching of the enamel causes a change of uptake. The outermost layer of the labial surface of extracted canines was removed by grinding and the enamel was covered with five different fluoride-containing materials ; a silicate, a composite resin, an amalgam, a silicophosphate, and a polycarboxylate luting cement. The material was either removed immediately or after storing the tooth in distilled water. The fluoride content was determined using a sensitive physical method based on the 19 F (p, αγ) 16 O reaction. In addition, the fluoride content of enamel after etching for different periods of time and of etched enamel which had been in contact with silicate cement was determined. The mean fluoride content of uncovered interior enamel was 226 parts 10 6 . All materials, except the composite, increased clearly the fluoride content of the underlying enamel. Etching of interior enamel also increased the fluoride values. No difference could be shown in fluoride uptake from silicate and composite resin between etched and unetched enamel. (author)

Fluoride ion recognition by chelating and cationic boranes.

Science.gov (United States)

Hudnall, Todd W; Chiu, Ching-Wen; Gabbaï, François P

2009-02-17

Because of the ubiquity of fluoride ions and their potential toxicity at high doses, researchers would like to design receptors that selectively detect this anion. Fluoride is found in drinking water, toothpaste, and osteoporosis drugs. In addition, fluoride ions also can be detected as an indicator of uranium enrichment (via hydrolysis of UF(6)) or of the chemical warfare agent sarin, which releases the ion upon hydrolysis. However, because of its high hydration enthalpy, the fluoride anion is one of the most challenging targets for anion recognition. Among the various recognition strategies that are available, researchers have focused a great deal of attention on Lewis acidic boron compounds. These molecules typically interact with fluoride anions to form the corresponding fluoroborate species. In the case of simple triarylboranes, the fluoroborates are formed in organic solvents but not in water. To overcome this limitation, this Account examines various methods we have pursued to increase the fluoride-binding properties of boron-based receptors. We first considered the use of bifunctional boranes, which chelate the fluoride anion, such as 1,8-diborylnaphthalenes or heteronuclear 1-boryl-8-mercurio-naphthalenes. In these molecules, the neighboring Lewis acidic atoms can cooperatively interact with the anionic guest. Although the fluoride binding constants of the bifunctional compounds exceed those of neutral monofunctional boranes by several orders of magnitude, the incompatibility of these systems with aqueous media limits their utility. More recently, we have examined simple triarylboranes whose ligands are decorated by cationic ammonium or phosphonium groups. These cationic groups increase the electrophilic character of these boranes, and unlike their neutral analogs, they are able to complex fluoride in aqueous media. We have also considered cationic boranes, which form chelate complexes with fluoride anions. Our work demonstrates that Coulombic and chelate

Separation of americium and plutonium from nuclear wastes by the TRUEX process

International Nuclear Information System (INIS)

Leonard, R.A.; Vandegrift, G.F.; Manry, C.W.

1986-01-01

Americium and plutonium can be removed from a transuranic (TRU) waste stream to <10 nCi/g by the TRUEX process. The resulting waste is nontransuranic, greatly reducing disposal costs. An overview is given of the TRUEX process and of centrifugal contactors used to implement this process. Then, a plan for the deployment of TRUEX at the Hanford Site is discussed. Finally, details are given on the proposed use of TRUEX to treat the liquid wastes from the Plutonium Finishing Plant at the Hanford Site

Fluoride reactions with dental enamel following different forms of fluoride supply

International Nuclear Information System (INIS)

Hellstroem, I.; Ericsson, Y.

1976-01-01

The reactions with dental enamel of NaF as tablets dissolved in different beverages or supplied with NaCl, simulating domestic salt fluoridation, were studied in tests with enamel surfaces and enamel powder. It was confirmed that powdered enamel can react quite differently from enamel surfaces under certain conditions. Enamel surfaces took up much more fluoride (F) from orange juice than from water or milk, and neither the low pH nor the citrate content of the juice increased the formation of unstable CaF 2 in the enamel, as judged from a KOH leaching test. The F uptake by enamel surfaces from 0.25 mM NaF in 175 mM NaCl, corresponding to a dish prepared with salt containing 500 parts/10 6 F, was about 80 percent greater than from the same NaF concentration in water. This NaCl concentration did not increase the formation of CaF 2 in the enamel, as judged from the KOH test, while 350 mM NaCl caused a moderate increase. The investigations support the administration of NaF tablets with orange juice and the plans for domestic salt fluoridation. (author)

Fluoride use in Controlling Dental Caries and Fluorosis

Directory of Open Access Journals (Sweden)

Gaurav Solanki

2012-07-01

Full Text Available Policy were introduced to control fluoride exposure and to reduce the prevalence of fluorosis. The study aimed of describing the prevalence, severity and risk factors for fluorosis, and to describe the trend of fluorosis among Indian children. The study also aimed of exploring the effect of the change in fluoride exposure on dental fluorosis and caries. Establishing an appropriate use of fluoride toothpaste could be successful in reducing fluorosis without a significant increase in caries experience. The use of fluorides for oral health has always involved a balance between the protective benefit against dental caries and the risk of developing fluorosis. The link between fluoride and dental health was established to determining the causes of dental fluorosis or enamel mottling. Fluorosis in Indian children was highly prevalent in the early 1990s.

Fluoride remediation using floating macrophytes

Directory of Open Access Journals (Sweden)

Naba Kumar Mondal

2014-04-01

Full Text Available Six aquatic macrophytes, such as Pistia stratiotes, Ceratophyllum demersum, Nymphoides indica, Lemna major, Azolla pinnata,and Eichhornia crassipes were considered for remove fluoride from aqueous solution. Five different concentrations (10, 30, 50, and 100 ppm of fluoride solution were taken in 1 L plastic container. Fixed weight (20 g of macrophytes along with 500 ml fluoride solution was taken in each plastic container for 72 hours observation. Results demonstrated all the macrophytes show highest fluoride removal during 24 h to 48 h, but after 72 h their efficiency reduced drastically. The species N. indica showed better removal efficiency than other experimental macrophytes. In general, pigment measurement data indicated higher concentration at 72 h. However, Pistia sp. showed higher concentration of pigmentation at intermediate time interval (48 h. Higher level of dry weight to fresh weight ratio was recorded for L. major and A. pinnata at all concentrations, excepting at 10 ppm. In addition, all macrophytes showed lower RGR at higher concentration. Isotherm study indicated that macrophyte C. demersum is a good fitted with Freundlich and Langmuir isotherm whereas L. major with Langmuir isotherm during 24 hours.

Density and surface tension of melts of zirconium and hafnium fluorides with lithium fluoride

International Nuclear Information System (INIS)

Katyshev, S.F.; Artemov, V.V.; Desyatnik, V.N.

1988-01-01

A study was conducted to determine the temperature dependence of the density and surface tension of melts of LiF-ZrF 4 and LiF-HfF 4 . Density and surface tension were determined by the method of maximum pressure in an argon bubble. On the basis of experimental data over the entire concentration range the molar volumes and their relative deviations from the additive molar volumes were calculated for 1100 0 K. The positive deviations of the molar volumes from additivity in the LiF-HfF 4 system (22.45%) were greater than in the LiF-ZrF 4 system (15.75%). This indicated that the reaction with lithium fluoride is intensified with the switch to the hafnium fluoride. Results also demonstrated that the fluorides are surface-active components in the molten mixtures

Coprecipitation of iron and silver with barium fluoride

International Nuclear Information System (INIS)

Kopilova, N.V.; Khamidov, B.O.; Kashina, Z.A.; Ikrami, D.D.

1986-01-01

Distribution of trace contaminants of iron and silver at coprecipitation of barium fluoride is studied in present work. It is defined that iron almost completely coprecipitated with barium fluoride in wide range of ph 5.5-12. Silver coprecipitated with barium fluoride in ph range 4-7. The value of coprecipitation varies from 94% to 100%.

Production of a square geometry Americium standard source for use with photodiodes

Energy Technology Data Exchange (ETDEWEB)

Costa, Priscila; Geraldo, Bianca; Raele, Marcus P.; Marumo, Júlio T.; Vicente, Roberto; Zahn, Guilherme S.; Genezini, Frederico A., E-mail: priscila3.costa@usp.br, E-mail: fredzini@ipen.br [Instituto de Pesquisas Energéticas e Nucleares (IPEN/CNEN-SP), São Paulo, SP (Brazil)

2017-07-01

In the development of a thermal neutron detector using a square photodiode and a thin boron film, a radioactive calibration source with the same geometry was needed. An americium-243 standard source was produced by electrodeposition aiming at the calibration of a PIN-type silicon photodiode with a detection area of 10 x 10 mm{sup 2}. To produce the samples two tests were performed. In the first test, a square stainless steel plate (10 x 10 mm{sup 2}) was fixed on the surface of the conventional plate, which was removed after deposition. To reduce the loss of activity of the source, in the second test nail polish was applied on the silver plate leaving only an area of 10 x 10 mm{sup 2} without varnish coating. Once the electrodeposition process was completed, the activity concentration measurement was performed by alpha particle spectrometry. The first method presented a lower activity when compared to the total activity of Am-243 added initially. For the second method, the total activity was concentrate in the exposed square region (without nail polish). The results showed that it is possible to obtain a square geometry source; furthermore, the surrounding nail polish was not contaminated by {sup 243}Am. The comparison of these two approaches indicated that the second method was more efficient as it was possible to concentrate all the americium activity in the delimited square area. (author)

Data on fluoride concentration level in villages of Asara (Alborz, Iran) and daily fluoride intake based on drinking water consumption.

Science.gov (United States)

Akhavan, Giti; Dobaradaran, Sina; Borazjani, Jaleh Mohajeri

2016-12-01

In the present data article, fluoride concentration levels of drinking water (with spring or groundwater sources) in 10 villages of Asara area located in Alborz province were determined by the standard SPADNS method using a spectrophotometer (DR/2000 Spectrophotometer, USA). Daily fluoride intakes were also calculated based on daily drinking water consumption. The fluoride content were compared with EPA and WHO guidelines for drinking water.

ADSORPTIVE REMOVAL OF FLUORIDE FROM WATER USING ...

African Journals Online (AJOL)

Preferred Customer

Currently available treatment methods for removal of excess fluoride from water are broadly divided into three ... the application of nanoparticles as sorbents for fluoride removal. Sundaram [26] studied the ... Characterization of adsorbent.

Process development for treatment of fluoride containing wastes

Energy Technology Data Exchange (ETDEWEB)

Singh, Mahesh; Kanvinde, V Y [Chemical Engineering Division, Bhabha Atomic Research Centre, Mumbai (India)

1994-06-01

Many chemical and metallurgical industries generate liquid wastes containing high values of fluorides in association of nitrates and other metals. Due to harmful effects of fluorides these type of wastes can not be disposed off in the environment without proper treatment. Bench-scale laboratory experiments were conducted to develop a process scheme to fix the fluorides as non-leachable solid waste and fluoride free treated liquid waste for their disposal. To optimize the important parameters, simulated synthetic and actual wastes were used. For this study, three waste streams were collected from Nuclear Fuel Complex, Hyderabad. (author). 6 tabs., 1 fig.

Toxicity of fluoride to microorganisms in biological wastewater treatment systems.

Science.gov (United States)

Ochoa-Herrera, Valeria; Banihani, Qais; León, Glendy; Khatri, Chandra; Field, James A; Sierra-Alvarez, Reyes

2009-07-01

Fluoride is a common contaminant in a variety of industrial wastewaters. Available information on the potential toxicity of fluoride to microorganisms implicated in biological wastewater treatment is very limited. The objective of this study was to evaluate the inhibitory effect of fluoride towards the main microbial populations responsible for the removal of organic constituents and nutrients in wastewater treatment processes. The results of short-term batch bioassays indicated that the toxicity of sodium fluoride varied widely depending on the microbial population. Anaerobic microorganisms involved in various metabolic steps of anaerobic digestion processes were found to be very sensitive to the presence of fluoride. The concentrations of fluoride causing 50% metabolic inhibition (IC(50)) of propionate- and butyrate-degrading microorganisms as well as mesophilic and thermophilic acetate-utilizing methanogens ranged from 18 to 43 mg/L. Fluoride was also inhibitory to nitrification, albeit at relatively high levels (IC(50)=149 mg/L). Nitrifying bacteria appeared to adapt rapidly to fluoride, and a near complete recovery of their metabolic activity was observed after only 4d of exposure to high fluoride levels (up to 500 mg/L). All other microbial populations evaluated in this study, i.e., glucose fermenters, aerobic glucose-degrading heterotrophs, denitrifying bacteria, and H(2)-utilizing methanogens, tolerated fluoride at very high concentrations (>500 mg/L).

Laboratory investigations into the potential anticaries efficacy of fluoride varnishes.

Science.gov (United States)

Lippert, Frank; Hara, Anderson Takeo; Martinez-Mier, Esperanza Angeles; Zero, Domenick T

2014-01-01

The purpose of this study was to investigate the potential anticaries efficacy of fluoride varnishes (FVs) by studying their ability to reharden and deliver fluoride to carious lesions and to release fluoride into saliva. Enamel carious lesions were created and allocated to 24 groups (11 FVs with two FV incubation times and two control groups) based on Knoop microhardness test values. FVs were applied to lesions, which were incubated in artificial saliva for two or six hours, with saliva being renewed hourly. FV was removed and lesions were remineralized in artificial saliva for 22 hours. Microhardness was measured and enamel fluoride uptake (EFU) was determined. Saliva samples (six-hour groups) were analyzed to determine fluoride release characteristics. Data were analyzed using analysis of variance. FVs differed considerably in their ability to reharden and deliver fluoride to carious lesions and in their fluoride release characteristics. Little consistency was found between investigated study variables for virtually all tested FVs. For example, a particular FV showed the highest EFU and fluoride release values but the lowest rehardening value. A longer FV contact time led to increased EFU for five of the 11 FVs. Some FVs delivered more fluoride to lesions in two hours than others did in six hours. Fluoride varnishes differ greatly in their in vitro anticaries efficacy.

Protective effect of fluoride varnish and fluoride gel on enamel erosion: roughness, SEM-EDS, and µ-EDXRF studies.

Science.gov (United States)

Soares, Luís Eduardo Silva; De Carvalho Filho, Antonio Carlos Belfort

2015-03-01

The effects of fluoride treatment on bovine enamel subjected to acid erosion were studied by roughness (Ra) measurements, scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and microenergy-dispersive X-ray fluorescence spectrometry (μ-EDXRF). Enamel samples (63) were divided into nine groups (n = 7): artificial saliva (AS), Pepsi Twist(®) (PT), orange juice (OJ), Duraphat(®)  + Pepsi Twist(®) (DPH/PT), Duraphat(®)  + orange juice (DPH/OJ), Duofluorid(®)  + Pepsi Twist(®) (DUO/PT), Duofluorid(®)  + orange juice (DUO/OJ), fluoride gel + Pepsi Twist(®) (FG/PT), and fluoride gel + orange juice (FG/OJ). Fluoride was applied and the samples were submitted to six cycles (demineralization: Pepsi Twist(®) or orange juice, 10 min; remineralization: saliva, 1 h). The enamel surface in depth was exposed and 63 line-scan maps were performed. The elemental analysis by EDS revealed that only fluoride treated groups had any detectable fluorine after erosion cycles (DPH/PT: 3.50 wt%; DPH/OJ: 3.37 wt%; DUO/PT: 2.69 wt%; DUO/OJ: 3.54 wt%; FG/PT: 2.17 wt%; FG/OJ: 2.77 wt%). PT treatment resulted in significantly higher Ra values than the artificial saliva (P < 0.001). Scanning electron microscopy (SEM) analysis of fluoride protected enamel showed areas with some globular structures or a residual layer of varnish. The enamel thickness was significantly lower in PT (0.63 ± 0.087 mm) than in DPH/PT (0.87 ± 0.16 mm) and DUO/PT (0.92 ± 0.14 mm) groups (P < 0.01). Fluoride treatments protected enamel without Ra increase and loss of enamel tissue. © 2015 Wiley Periodicals, Inc.

Water fluoridation for the prevention of dental caries.

Science.gov (United States)

Iheozor-Ejiofor, Zipporah; Worthington, Helen V; Walsh, Tanya; O'Malley, Lucy; Clarkson, Jan E; Macey, Richard; Alam, Rahul; Tugwell, Peter; Welch, Vivian; Glenny, Anne-Marie

2015-06-18

Dental caries is a major public health problem in most industrialised countries, affecting 60% to 90% of school children. Community water fluoridation was initiated in the USA in 1945 and is currently practised in about 25 countries around the world; health authorities consider it to be a key strategy for preventing dental caries. Given the continued interest in this topic from health professionals, policy makers and the public, it is important to update and maintain a systematic review that reflects contemporary evidence. To evaluate the effects of water fluoridation (artificial or natural) on the prevention of dental caries.To evaluate the effects of water fluoridation (artificial or natural) on dental fluorosis. We searched the following electronic databases: The Cochrane Oral Health Group's Trials Register (to 19 February 2015); The Cochrane Central Register of Controlled Trials (CENTRAL; Issue 1, 2015); MEDLINE via OVID (1946 to 19 February 2015); EMBASE via OVID (1980 to 19 February 2015); Proquest (to 19 February 2015); Web of Science Conference Proceedings (1990 to 19 February 2015); ZETOC Conference Proceedings (1993 to 19 February 2015). We searched the US National Institutes of Health Trials Registry (ClinicalTrials.gov) and the World Health Organization's WHO International Clinical Trials Registry Platform for ongoing trials. There were no restrictions on language of publication or publication status in the searches of the electronic databases. For caries data, we included only prospective studies with a concurrent control that compared at least two populations - one receiving fluoridated water and the other non-fluoridated water - with outcome(s) evaluated at at least two points in time. For the assessment of fluorosis, we included any type of study design, with concurrent control, that compared populations exposed to different water fluoride concentrations. We included populations of all ages that received fluoridated water (naturally or artificially

Water Fluoridation Reporting System (Public Water Systems)

Data.gov (United States)

U.S. Department of Health & Human Services — The Water Fluoridation Reporting System (WFRS) has been developed to provide tools to assist states in managing fluoridation programs. WFRS is designed to track all...

FLUORIDE CONTENT OF COMMERCIALLY AVAILABLE SOY MILK PRODUCTS IN THAILAND.

Science.gov (United States)

Rirattanapong, Opas; Rirattanapong, Praphasri

2016-01-01

Abstract. In Thailand, the consumption of soy milk products is common but there is limited data about their fluoride content. The purpose of this study was to es- timate the fluoride content of soy milk products available in Thailand. Fluoride content was determined for 76 brands of soy milk using a F-ion-specific electrode. The fluoride concentrations ranged from 0.01 to 3.78 μg/ml. The fluoride content was not related to sugar content, soy bean content or the sterilization process. Among 3 brands of soy milk containing tea powder extract, the fluoride content was high (1.25 to 3.78 μg/ml). Most brands of soy milk tested in our study had fluoride content below the optimal daily intake but brands containing tea powder extract if consumed by children may increase their risk for fluorosis.

Comparative evaluation of fluoride release and recharge of pre-reacted glass ionomer composite and nano-ionomeric glass ionomer with daily fluoride exposure: An in vitro study

Directory of Open Access Journals (Sweden)

Jayanthi Mungara

2013-01-01

Full Text Available Aim: This in vitro study was designed to investigate the effects of daily fluoride exposures on fluoride release and recharge by prereacted glass ionomer (PRG composite and nano-ionomeric glass ionomer. Materials and Methods: Seventy-two specimens (36 of each material were prepared and by placing the restorative materials into Teflon mold. Each specimen was subjected to one of three daily treatments (n = 12: (1 No fluoride treatment (control; (2 application of a fluoride dentifrice (1,000 ppm once daily; and (3 the same regimen as (2, plus immersion in a 0.05% sodium fluoride (NaF mouth rinse (225 ppm immediately following the dentifrice application. Specimens were suspended in a storage vial containing 10 ml demineralizing solution for 6 h and transferred to a new test tube containing 10 ml remineralizing solution for 18 h. Fluoride treatments of the specimens were completed every day prior to their immersion in the demineralizing solution. Media solutions were buffered with equal volumes of total ionic strength adjustment buffer (TISAB II; fluoride levels were measured using a digital ion analyzer and fluoride electrode throughout the 21 day duration of the experiment. Results: Nano-ionomeric glass ionomer showed a better amount of fluoride release than PRG composite irrespective of the fluoride treatment supplementation (P < 0.01. Additional fluoride supplementation improved fluoride release and recharge ability for both the materials when compared to their respective control groups. The fluoride recharge for both materials did not show any sustained pattern of release. Conclusion: Nano-ionomeric glass ionomer demonstrated a greater ability to release and recharge compared with that of PRG composite.

Fluoride removal from water by nano filtration

International Nuclear Information System (INIS)

Bejaoui, Imen; Mnif, Amine; Hamrouni, Bechir

2009-01-01

As any oligo element, fluoride is necessary and beneficial for human health to low concentrations, but an excess amount of fluoride ions in drinking water has been known to cause undesirable effects, especially tooth and bones fluoro sis. The maximum acceptable concentration of fluoride in drinking water was fixed by the World Health Organization according to the climate in the range of 1 mg.L -1 to 1,2 mg.L -1 . Many methods have been used to remove fluoride from water such as precipitation, adsorption, electrocoagulation and membrane processes. Technologies using membrane processes are being used in many applications, particularly for brackish water desalination. Nano filtration seems to be the best process for a good selective defluorination of fluorinated waters. The main objective of this work was to investigate the retention of fluoride anions by nano filtration. The first part of this study deals with the characterisation of the NF HL2514TF membrane. The influence of various experimental parameters such as initial fluoride content, feed pressure, permeate flux, ionic strength, type of cation associated to fluoride and pH were studied in the second part. Results show that the retention order for the salts tested was TR(Na 2 SO 4 ) > TR(CaCl 2 ) > TR(NaCl), showing a retention sequence inversely proportional to the salt diffusion coefficients in water. It was also shown that charge effects could not be neglected, and a titration experiments confirmed that the NF membrane carry a surplus of negatively charged groups. Fluoride retention exceeds 60 pour cent, and increases with increasing concentration, where the rejection mechanism is related to the dielectric effects. Speigler-Kedem model was applied to experimental results in the aim to determine phenomenological parametersσand P s respectively, the reflexion coefficient of the membrane and the solute permeability of ions. The convective and diffusive parts of the mass transfer were quantified with

Studies on the comparative effect of sodium fluoride on collagen ...

African Journals Online (AJOL)

Fluoride is an essential element for the normal development and growth of human beings. The main source of fluoride for humans is the intake of groundwater. At high levels, fluoride causes dental and skeletal fluorosis. In this study, control and sodium fluoride (NaF) treated groups of rats had significant (p < 0.05) higher ...

Contribution to the prediction of americium, plutonium and neptunium behaviour in the geosphere: chemical data

International Nuclear Information System (INIS)

Robouch, P.

1989-01-01

An exhaustive bibliographic review on hydrolysis of americium gives the stability constants, at zero ionic strength. No evidence of Am(OH) 4 - formation was found by solubility studies up to pH 2 (CO 3 ) 3 characterised by its X-ray diffraction pattern is studied at a high ionic strength. All the published results on Am in carbonate media are reinterpreted using these stability constants (Am-OH-CO 3 complexes are not needed). No evidence of Am(CO 3 ) 4 5- formation was found by spectrophotometry up to 3M. Literature results are used to determine the formal redox potentials at pH = 9.4 and to calculate the formation constants, at zero ionic strength. The formation of complexes between americium and humic materials (purified fulvic and humic acids) has been studied by a spectrophotometric technique. The results are interpreted by the formation of a 1:1 complexe. Solubility of the solid PuO 2 (CO 3 ) is measured in bicarbonate media at high ionic strength, to obtain the solubility product and formation constants of the PuO 2 (CO 3 ) i 2-2i complexes [fr

Measurements of α-emitting plutonium and americium in the intertidal sands of west Cumbria, UK

International Nuclear Information System (INIS)

Eakins, J.D.; Morgan, A.; Baston, G.M.N.; Pratley, F.W.; Strange, L.P.; Burton, P.J.

1990-01-01

Samples of surface sand and sand cores were collected from intertidal regions of west Cumbria between Silloth and Walney Island (including the Duddon Estuary) between 1982 and 1984 and analysed for 238 Pu, 239+240 Pu and 241 Am. Generally, more than 95% of the α-emitting transuranic nuclides were associated with the sand and less than 5% with entrained silt. The greatest concentrations of both plutonium and americium were found at Braystones. Concentrations declined with distance from the Sellafield Works. The largest actinide deposits occurred at Drigg (320 and 720 kBq m -2 of 239+240 Pu and 241 Am respectively). The integrated deposits in intertidal sand between Silloth and Walney Island were about 4.2 and 7.0 TBq respectively, which represent about 1% of the total α-emitting activity discharged to sea from Sellafield Works up to 1982. The corresponding value for the Duddon Estuary is about 0.3%. Only on beaches close to Sellafield did levels of man-made α-emitters exceed those of natural α-emitting nuclides. The radiological consequences of the intertidal inventory of plutonium and americium are shown to be very small and much less than from the seafood pathway. (author)

Spectrophotometric determination of fluoride with alizarin complexone

Energy Technology Data Exchange (ETDEWEB)

Marczenko, Z; Lenarczyk, L [Politechnika Warszawska (Poland)

1976-01-01

The modification of direct spectrophotometric method of fluoride determination by alizarin complexone has been developed. It was shown that the lanthanum alizarin complexone chelate is more convenient than that of cerium (3). The influence of acetone, dioxane and dimethyl sulphoxide in water solution on the increase of sensitivity of the method and the rate of colour reaction has been determined. The optimal pH ranges for the reaction with lanthanum and cerium (3) have been estimated. Some amines having a large molecule are useful for extraction of blue fluoride complex with isobutanol. Dioctylamine was applied in a new extraction spectrophotometric procedure of fluoride determination. Conditions in reagent have been established. Both variants of the method have been applied to the fluoride determination in several chemicals. The obtained results show a good precision and accuracy.

Removal of fluoride from water using aluminium containing compounds

Institute of Scientific and Technical Information of China (English)

M. Karthikeyan; K. P. Elango

2009-01-01

Batch adsorption studies were undertaken to assess the suitability of aluminium titanate (AT) and bismuth aluminate (BA) to remove fluoride ions from water.The effect of pH,dose of adsorbent,contact time,initial concentration,co-ions and temperature on fluoride removal efficiency were studied.The amounts of fluoride ions adsorbed,at 30℃ from 4 mg/L of fluoride ion solution,by AT and BA are 0.85 and 1.55 mg/g,respectively.The experimental data fitted well to the Freundlich and Langmuir isotherms.Thermodynamic parameters such as △H~0,△S~0 and △G~0 indicated that the removal of fluoride ions by AT is exothermic and non-spontaneous while that by BA is endothermic and spontaneous.Furrier transform infrared (FT-IR) analysis and X-ray diffraction (XRD) patterns of the adsorbent before and after adsorption indicated that fluoride ions are chemisorbed by these adsorbents.

Synthesis and characterization of ruthenium fluorides and oxide fluorides with high oxidation states

International Nuclear Information System (INIS)

Meublat, L.

1989-10-01

The synthesis of ruthenium fluorides and oxide fluorides with high oxidation states was attempted from dioxide RuO 2 and tetroxide RuO 4 . Three fluorinating agents were used: fluorine, chlorine trifluoride and krypton difluoride. The reactions were achieved in anhydrous hydrogen fluoride at room temperature. Thus, the reaction of RuO 4 with CIF 3 enabled us to prepare chloryl hexafluororuthenate (V), CIO 2 + RuF 6 - , a new compound well identified by vibrational spectroscopy (infra-red and Raman), the structure of which was determined. The reaction of KrF 2 with RuO 4 gave the oxide tetrafluoride RuOF 4 , the previously published syntheses and properties of which were not in agreement with each other. This compound was definitely characterized here by chemical analysis, infra-red spectroscopy and X-ray powder diffraction. The product of thermal decomposition (70 0 C) of RuOF 4 is presumably RuF 4 since only oxygen is liberated during this decomposition. At last, the reaction of KrF 2 with RuO 2 probably leads to the formation of the new oxide fluoride RuO 2 F 4 . Indeed, no oxygen is given off during this reaction, the chemical analysis of the red-orange coloured solid residue is almost in agreement with the one proposed and its infra-red absorption spectrum indicates the presence of ruthenium-oxygen and ruthenium-terminal and bridging fluorine bonds [fr

Synthesis and characterization of ruthenium fluorides and oxide fluorides with high oxidation states

International Nuclear Information System (INIS)

Meublat, L.

1989-01-01

The synthesis of ruthenium fluorides and oxide fluorides with high oxidation states was attempted from dioxide RuO 2 and tetroxide RuO 4 . Three fluorinating agents were used: fluorine, chlorine trifluoride and krypton difluoride. The reactions were achieved in anhydrous hydrogen fluoride at room temperature. Thus, the reaction of RuO 4 with CIF 3 enabled us to prepare chloryl hexafluororuthenate (V), ClO 2 + RuF 6 - , a new compound well idendified by vibrational spectroscopy (infra-red and Raman), the structure of which was determined. The reaction of KrF 2 with RuO 4 gave the oxide tetrafluoride RuOF 4 , the previously published syntheses and properties of which were not in agreement with each other. This compound was definitely characterized here by chemical analysis, infra-red spectroscopy and X-ray powder diffraction. The product of thermal decomposition (70 0 C) of RuOF 4 is presumably RuF 4 since only oxygen is liberated during this decomposition. At last, the reaction of KrF 2 with RuO 2 probably leads to the formation of the new oxide fluoride RuO 2 F 4 . Indeed, no oxygen is given off during this reaction, the chemical analysis of the red-orange coloured solid residue is almost in agreement with the one proposed and its infra-red absorption spectrum indicates the presence of ruthenium-oxygen and ruthenium-terminal and bridging fluorine bonds [fr

Purification of Drinking Water from Fluorides by Reverse Osmosis

Directory of Open Access Journals (Sweden)

Aleksander A.

2018-03-01

Full Text Available Introduction: An important task in the sphere of sanitary and epidemiological welfare of the population of the Russian Federation is provision of drinking water. Tap water must not contain pathogenic bacteria and dangerous chemicals. Purification systems regulate the concentration of fluoride ions in drinking water. The aim of this paper is to study the possibility of purifying tap water from fluoride ions by reverse osmosis. Materials and Methods: We used the Alfa Laval PilotUnit 2.5 "RO/NF with a set of spiral-type membrane elements RO99-2517/48 to remove fluoride ions. We measured the concentration of fluoride ions by the potentiometric method using the Hanna HI 2211 (pH/mV/T. Fluoride-selective electrode ELIS 131 F was used as an indicator electrode and the standard chloride-silver electrode EVL-1M3 was used as a reference electrode. Both the calibration and buffer solutions were prepared from chemically pure reagents and A. R. purity for analysis reagents according to GOST 4386-89. Results: A single passage of water through the reverse osmosis membrane reduced the concentration of fluoride ions from 2.29 ± 0.02 to 0.240 ± 0.015 mg/l. Double passage of water reduced the concentration by a factor of two. As the concentration of fluoride ions increased in the retentate, the concentration in the filtrate slightly increased too. Purification of water reduced the concentration of fluoride ions from 20 mg/l, to 0.5 mg/l. Discussion and Conclusions: Thus, using the Alfa Laval PilotUnit 2.5" RO/NF with a set of spiral-type membrane elements RO99-2517/48 filters tap water of ions of fluoride to the maximum allowable concentration. This study opens the perspective of using reverse osmosis to purify tap water with high concentration of fluoride ions.

Elimination of americium-241 after a case of accidental inhalation

International Nuclear Information System (INIS)

Edvardsson, K.A.; Lindgren, L.

1976-01-01

In handling a 241 Am source one person received an internal contamination of about 140 nCi of americium oxide, which was deposited in the lung region. Elimination of the activity was followed for more than 3 months by external gamma counting and excreta analyses. During the first week after the inhalation about 80% of the total intake was eliminated with an effective half-life of less than 2 days. The remaining activity, deposited in the lung region, was eliminated with an effective half-life of about 17 days. About 15% of the activity eliminated from the lung region from the 10th to the 50th day was eliminated in the faeces. (author)

Formation of actinide hexafluorides at ambient temperatures with krypton difluoride

International Nuclear Information System (INIS)

Asprey, L.B.; Eller, P.G.; Kinkead, S.A.

1986-01-01

A second low-temperature agent, krypton difluoride, for generating volatile plutonium hexafluoride is reported (dioxygen difluoride is the only other reported agent). Plutonium hexafluoride is formed at ambient or lower temperature by the treatment of various solid substrates with krypton difluoride. Volatilization of uranium and neptunium from solid substrates using gaseous krypton difluoride is also reported for the first time. The formation of actinide hexafluorides has been confirmed for the reaction of krypton difluoride in anhydrous HF with UO 2 and with uranium and neptunium fluorides at ambient temperatures. Treatment of americium dioxide with krypton difluoride did not yield americium hexafluoride under the conditions studied. 15 references, 2 figures

Emissions of fluorides from welding processes.

Science.gov (United States)

Szewczyńska, Małgorzata; Pągowska, Emilia; Pyrzyńska, Krystyna

2015-11-01

The levels of fluoride airborne particulates emitted from welding processes were investigated. They were sampled with the patented IOM Sampler, developed by J. H. Vincent and D. Mark at the Institute of Occupational Medicine (IOM), personal inhalable sampler for simultaneous collection of the inhalable and respirable size fractions. Ion chromatography with conductometric detection was used for quantitative analysis. The efficiency of fluoride extraction from the cellulose filter of the IOM sampler was examined using the standard sample of urban air particle matter SRM-1648a. The best results for extraction were obtained when water and the anionic surfactant N-Cetyl-N-N-N-trimethylammonium bromide (CTAB) were used in an ultrasonic bath. The limits of detection and quantification for the whole procedure were 8μg/L and 24μg/L, respectively. The linear range of calibration was 0.01-10mg/L, which corresponds to 0.0001-0.1mg of fluorides per m(3) in collection of a 20L air sample. The concentration of fluorides in the respirable fraction of collected air samples was in the range of 0.20-1.82mg/m(3), while the inhalable fraction contained 0.23-1.96mg/m(3) of fluorides during an eight-hour working day in the welding room. Copyright © 2015. Published by Elsevier B.V.

Clinical Usefulness of 18F-fluoride Bone PET

International Nuclear Information System (INIS)

Kang, Ji Yeon; Lee, Won Woo; Lee, Byung Chul; Kim, Sang Eun; So, Young

2010-01-01

18 F-fluoride bone positron emission tomography (PET) has been reported as a useful bone imaging modality. However, no clinical bone PET study had been performed previously in Korea. The authors investigated the usefulness of 18 F-fluoride bone PET in Korean patients with malignant or benign bone disease. Eighteen consecutive patients (eight women, ten men; mean age, 55±12 years) who had undergone 18 F-fluoride bone PET for the evaluation of bone metastasis (n=13) or benign bone lesions (n=5) were included. The interpretation of bone lesions on 18 F-fluoride bone PET was determined by consensus of two nuclear medicine physicians, and final results were confirmed using combination of all imaging studies and/or clinical follow-up. The analysis was performed on the basis of lesion group. Thirteen patients with malignant disease had 15 lesion groups, among which seven were confirmed as metastatic bone lesions and eight were confirmed as non-metastatic lesions. 18 F-fluoride bone PET correctly identified six of seven metastatic lesions (sensitivity, 86%), and seven of eight non-metastatic lesions (specificity, 88%). On the other hand, five patients with benign conditions had five bone lesion groups; four were confirmed as benign bone diseases and the other one was confirmed as not a bone lesion. 18 F-fluoride bone PET showed correct results in all the five lesion groups. 18 F-fluoride bone PET showed promising potential for bone imaging in Korean patients with malignant diseases as well as with various benign bone conditions. Therefore, further studies are required on the diagnostic performance and cost-effectiveness of 18 F-fluoride bone PET.

Protection From Dental Erosion: All Fluorides are Not Equal.

Science.gov (United States)

Faller, Robert V; Noble, Warden H

2018-03-01

All fluoride sources help strengthen teeth against bacterial acids that cause caries. However, excessive exposure to dietary acids, which can result in dental erosion, presents a more aggressive level of challenge compared to caries. Despite the fact that almost all toothpastes contain fluoride, both the incidence and prevalence of dental erosion appear to be on the rise. This article: (1) describes key differences between caries and dental erosion and the ability of different fluoride sources to help prevent erosion; (2) discusses the importance of the evaluation of patients for dental erosion at the earliest stages using the Basic Erosive Wear Examination scoring system to help assess and educate patients; and (3) provides evidence-based information for making specific recommendations to patients with dental erosion. The objective of this article is to assess the comparative ability of fluoride agents to protect against dental erosion. Though all fluorides are able to help strengthen teeth against cariogenic acids, not all available sources of fluoride provide the same level of erosion protection. Daily use of a stabilized stannous fluoride dentifrice has been shown to provide the most effective means of protecting teeth against the increasing risk of dental erosion and erosive tooth wear.

Chemical mechanism of the fluoride-inhibition of fermentation

Energy Technology Data Exchange (ETDEWEB)

Warburg, O; Christian, W

1941-08-01

Among the fluoride-sensitive fermentation elements, enolase is the most sensitive. An investigation was made, quantitatively, of fluoride inhibition for chemically pure magnesium-enolase using an optical enolase test. Data show that the effective compound for fluoride inhibition is a complex magnesium-fluoro-phosphate and that the magnesium-fluoro-phosphate inhibits fermentation by combining proportionally to its concentration with the ferment-protein in a dissociating manner.

Magnesium fluoride recovery method

International Nuclear Information System (INIS)

Gay, R.L.; McKenzie, D.E.

1989-01-01

A method of obtaining magnesium fluoride substantially free from radioactive uranium from a slag formed in the production of metallic uranium by the reduction of depleted uranium tetrafluoride with metallic magnesium in a retort wherein the slag contains the free metals magnesium and uranium and also oxides and fluorides of the metals. The slag having a radioactivity level of at least about 7,000 rhoCi/gm. The method comprises the steps of: grinding the slag to a median particle size of about 200 microns; contacting the ground slag in a reaction zone with an acid having a strength of from about 0.5 to 1.5 N for a time of from about 4 to about 20 hours in the presence of a catalytic amount of iron; removing the liquid product; treating the particulate solid product; repeating the last two steps at least one more time to produce a solid residue consisting essentially of magnesium fluoride substantially free of uranium and having a residual radioactivity level of less than about 1000 rhoCi/gm

Performance of novel hydroxyapatite nanowires in treatment of fluoride contaminated water

Energy Technology Data Exchange (ETDEWEB)

He, Junyong; Zhang, Kaisheng [Nano-Materials and Environmental Detection Laboratory, Institute of Intelligent Machines, Chinese Academy of Sciences, Hefei 230031 (China); Department of Chemistry, University of Science and Technology of China, Hefei, Anhui 230026 (China); Wu, Shibiao [Nano-Materials and Environmental Detection Laboratory, Institute of Intelligent Machines, Chinese Academy of Sciences, Hefei 230031 (China); Cai, Xingguo; Chen, Kai; Li, Yulian [Nano-Materials and Environmental Detection Laboratory, Institute of Intelligent Machines, Chinese Academy of Sciences, Hefei 230031 (China); Department of Chemistry, University of Science and Technology of China, Hefei, Anhui 230026 (China); Sun, Bai; Jia, Yong; Meng, Fanli; Jin, Zhen [Nano-Materials and Environmental Detection Laboratory, Institute of Intelligent Machines, Chinese Academy of Sciences, Hefei 230031 (China); Kong, Lingtao, E-mail: ltkong@iim.ac.cn [Nano-Materials and Environmental Detection Laboratory, Institute of Intelligent Machines, Chinese Academy of Sciences, Hefei 230031 (China); Liu, Jinhuai [Nano-Materials and Environmental Detection Laboratory, Institute of Intelligent Machines, Chinese Academy of Sciences, Hefei 230031 (China)

2016-02-13

Highlights: • Novel ultralong hydroxyapatite (HAP) nanowires were developed for effective defluoridation. • High fluoride adsorption capacity, 40.65 mg/g at neutral pH. • The HAP nanowire membrane efficiently removed fluoride by dynamic adsorption. • The membrane could remove more than 98% fluoride, and filtered water amount reached 350 L/m{sup 2}. - Abstract: Novel ultralong hydroxyapatite (HAP) nanowires were successfully prepared for fluoride removal for the first time. The fluoride adsorption on the HAP nanowires was studied on a batch mode. The results revealed that the adsorption data could be well described by the Freundlich model, and the adsorption kinetic followed the pseudo-second-order model. The maximum of adsorption capacity was 40.65 mg/g at pH 7.0 when the fluoride concentration is 200 mg/L. The thermodynamic parameters suggested that the adsorption of fluoride was a spontaneous endothermic process. The FT-IR, XPS and Zeta potential analysis revealed that both anion exchange and electrostatic interactions were involved in the adsorption of fluoride. Furthermore, the HAP nanowires were made into HAP membrane through a simple process of suction filtration. Membrane filtration experiments revealed that the fluoride removal capabilities depended on the membrane thickness, flow rate and initial concentration of fluoride. The as-prepared membrane could remove fluoride efficiently through continues filtration. The filtered water amount could reach 350, 192, and 64 L/m{sup 2} when the fluoride concentrations were 4, 5 and 8 ppm, respectively, using the HAP membrane with only 150 μm thickness. The as-synthesized ultralong HAP nanowires were thus demonstrated to be very effective and biocompatible adsorbents for fluoride removal from contaminated water.

Preparation and study of chlorine mono-fluoride and of chlorine oxi-fluorides; Preparation et etude du monofluorure et des oxyfluorures de chlore

Energy Technology Data Exchange (ETDEWEB)

Macheteau, Yves

1969-07-01

The objective of this engineering school report was to be a contribution to the study of a family of fluorine compounds: chlorine mono-fluoride (ClF), chlorine fluoride oxide (ClOF), chloryl fluoride (ClO{sub 2}F), perchloryl fluoride (ClO{sub 3}F) and perchloryl oxi-fluoride (ClO{sub 4}F). Such a study required very pure products to be obtained in order to be able to characterize them by different methods (infrared, micro-sublimation, and chromatography). The thermolysis of ClO{sub 2}F and ClO{sub 4}F has been particularly studied, and magnetic resonance has been used to establish a relationship between fluorine chemical displacement and the electro-negativity of the F-X bond where X represents the atom group to which fluorine is bonded.

SPHERE: Irradiation of sphere-pac fuel of UPuO2−x containing 3% Americium

International Nuclear Information System (INIS)

D’Agata, E.; Hania, P.R.; McGinley, J.; Somers, J.; Sciolla, C.; Baas, P.J.; Kamer, S.; Okel, R.A.F.; Bobeldijk, I.; Delage, F.; Bejaoui, S.

2014-01-01

Highlights: • SPHERE is designed to check the behaviour of MADF sphere-pac concept. • MADF sphere-pac are compared with MADF pellet. • Swelling, helium release and restructuring behaviour will be the main output of the experiment. • An experiment to check sphere-pac MABB fuel behaviour is now under design. - Abstract: Americium is a strong contributor to the long term radiotoxicity of high activity nuclear waste. Transmutation by irradiation in nuclear reactors of long-lived nuclides like 241 Am is therefore an option for the reduction of radiotoxicity of waste packages to be stored in a repository. The SPHERE irradiation experiment is the latest of a series of European experiments on americium transmutation (e.g. EFTTRA-T4, EFTTRA-T4bis, HELIOS, MARIOS) performed in the HFR (High Flux Reactor). The SPHERE experiment is carried out in the framework of the 4-year project FAIRFUELS of the EURATOM 7th Framework Programme (FP7). During the past years of experimental works in the field of transmutation and tests of innovative nuclear fuels, the release or trapping of helium as well as helium induced fuel swelling have been shown to be the key issues for the design of Am-bearing targets. The main objective of the SPHERE experiment is to study the in-pile behaviour of fuel containing 3% of americium and to compare the behaviour of sphere-pac fuel to pellet fuel, in particular the role of microstructure and temperature on fission gas release (mainly He) and on fuel swelling. The SPHERE experiment is being irradiated since September 2013 in the HFR in Petten (The Netherlands) and is expected to be terminated in spring 2015. The experiment has been designed to last up to 18 reactor cycles (corresponding to 18 months) but may reach its target earlier. This paper discusses the rationale and objective of the SPHERE experiment and provides a general description of its design

Sulfochlorphenol S as reagent for direct photometric determination of fluorides

International Nuclear Information System (INIS)

Dzhashi, D.O.; Dedkova, V.P.; Savvin, S.B.

1978-01-01

The system of zirconium-sulfochlorphenol S-fluoride was studied by the spectrophotometry method. The effect of pH, temperature and time on the formation of zirconium complexes with sulfochlorphenol S was investigated. A comparison of the above method of determining fluorides with other methods (using alizarinecomplexonate, quinalizarincomplexonate, cerium chelates, lanthanum, arsenazo 3) is presented. The sensitivity of determining fluorides with arsenazo 3 is lower than that with sulfochlorphenol S. The molar absorption coefficient is 3x10 4 , the reaction of determining fluorides with the aid of sulfochlorphenol S is highly selective. The method was used to determine fluorides in the supply water, zirconium solutions and electrolyzer cell. The range of concentration determination for fluorides is 0-3 μg/25 ml

Effect of fluoride pretreatment on the solubility of synthetic carbonated apatite.

Science.gov (United States)

Barry, A B; Zhuang, H; Baig, A A; Higuchi, W I

2003-03-01

The purpose of this research was to address the following question: How is the solubility of fluoride-pretreated carbonated apatite (CAP) in aqueous acidic media related to the equilibrium solution fluoride and/or the CAP adsorbed fluoride levels? A CAP sample prepared by a precipitation method at 70 degrees C containing approximately 6% carbonate was fluoride-treated (F adsorption from neutral aqueous solutions) to yield a approximately 1000 ppm F CAP and a approximately 3300 ppm F CAP. Metastable equilibrium solubility distributions were determined in acetate buffers at pH 5.0. Solution fluoride, calcium, phosphate, and pH were determined from the equilibrated solutions. The equilibrium solution fluoride levels were extremely low, e.g., as low as approximately 0.10 ppb to approximately 0.30 ppb at 50% dissolved for the two CAP preparations. The approximately 3300 ppm F CAP yielded a lower solubility than the approximately 1000 ppm F CAP (shift in the mean pKHAP value of 1.5-2 units). This can be attributed to the lower solution F(-) for the sample containing approximately 1000 ppm fluoride compared with the approximately 3300 ppm fluoride-containing CAP. These important findings suggest that a fluoride treatment simply may provide an adsorption fluoride depot for subsequent release, providing a solution fluoride effect upon the CAP solubility and not necessarily any intrinsic alteration of the mineral solubility.

Fluoride loaded polymeric nanoparticles for dental delivery.

Science.gov (United States)

Nguyen, Sanko; Escudero, Carlos; Sediqi, Nadia; Smistad, Gro; Hiorth, Marianne

2017-06-15

The overall aim of the present paper was to develop fluoride loaded nanoparticles based on the biopolymers chitosan, pectin, and alginate, for use in dental delivery. First, the preparation of nanoparticles in the presence of sodium fluoride (NaF) as the active ingredient by ionic gelation was investigated followed by an evaluation of their drug entrapment and release properties. Chitosan formed stable, spherical, and monodisperse nanoparticles in the presence of NaF and tripolyphoshate as the crosslinker, whereas alginate and pectin were not able to form any definite nanostructures in similar conditions. The fluoride loading capacity was found to be 33-113ppm, and the entrapment efficiency 3.6-6.2% for chitosan nanoparticles prepared in 0.2-0.4% (w/w) NaF, respectively. A steady increase in the fluoride release was observed for chitosan nanoparticles prepared in 0.2% NaF both in pH5 and 7 until it reached a maximum at time point 4h and maintained at this level for at least 24h. Similar profiles were observed for formulations prepared in 0.4% NaF; however the fluoride was released at a higher level at pH5. The low concentration, but continuous delivery of fluoride from the chitosan nanoparticles, with possible expedited release in acidic environment, makes these formulations highly promising as dental delivery systems in the protection against caries development. Copyright © 2017 Elsevier B.V. All rights reserved.

Fluoride Concentration of Drinking-Water of Qom, Iran

Directory of Open Access Journals (Sweden)

Ahmad Reza Yari

2016-03-01

Full Text Available Background and Purpose: Fluoride is a natural element essential for human nutrition due to its benefits for dental enamel. It is well-documented that standard amounts of fluoride in drinkingwater can decrease the rate of dental caries. This study was conducted with the aim of measuring fluoride concentration of drinking-water supplies and urban distribution system in Qom, Iran. Materials and Methods: Results were subsequently compared against national and international standards. All sources of drinking-water of rural and urban areas were examined. To measure fluoride, the standard SPADNS method and a DR/4000s spectrophotometer were used. Results: Results showed that the mean of fluoride concentration in rural areas, mainly supplied with groundwater sources, was 0.41 mg/L, that of the urban distribution system 0.82 mg/L, that of Ali-Abad station 0.11 mg/L, and that of the private water desalination system 0.24 mg/L. Due to the hot climate of Qom, fluoride concentration means of all sources were lower than the permissible standards set by Iranian Standards and the WHO guidelines (except those of some of the groundwater sources and urban distribution systems. Conclusion: It seems that in most of the drinking-water sources the average fluoride concentration is not enough to prevent dental caries or strengthen dental enamel. It is concluded that Qom’s drinkingwater would require at least 0.4 mg/L to reach the minimum desirable standard.

Removal of fluoride from aqueous nitric acid

International Nuclear Information System (INIS)

Pruett, D.J.; Howerton, W.B.; Mailen, J.C.

1981-06-01

Several methods for removing fluoride from aqueous nitric acid were investigated and compared with the frequently used aluminum nitrate-calcium nitrate (Ca 2+ -Al 3+ ) chemical trap-distillation system. Zirconium oxynitrate solutions were found to be superior in preventing volatilization of fluoride during distillation of the nitric acid, producing decontamination factors (DFs) on the order of 2 x 10 3 (vs approx. 500 for the Ca 2+ -Al 3+ system). Several other metal nitrate systems were tested, but they were less effective. Alumina and zirconia columns proved highly effective in removing HF from HF-HNO 3 vapors distilled through the columns; fluoride DFs on the order of 10 6 and 10 4 , respectively, were obtained. A silica gel column was very effective in adsorbing HF from HF-HNO 3 solutions, producing a fluoride DF of approx. 10 4

Monitoring of fluoride in water samples using a smartphone

International Nuclear Information System (INIS)

Levin, Saurabh; Krishnan, Sunderrajan; Rajkumar, Samuel; Halery, Nischal; Balkunde, Pradeep

2016-01-01

In several parts of India, groundwater is the only reliable, year round source for drinking water. Prevention of fluorosis, a chronic disease resulting from excess intake of fluoride, requires the screening of all groundwater sources for fluoride in endemic areas. In this paper, the authors present a field deployable colorimetric analyzer based on an inexpensive smartphone embedded with digital camera for taking photograph of the colored solution as well as an easy-fit, and compact sample chamber (Akvo Caddisfly). Phones marketed by different smartphone makers were used. Commercially available zirconium xylenol orange reagent was used for determining fluoride concentration. A software program was developed to use with the phone for recording and analyzing the RGB color of the picture. Linear range for fluoride estimation was 0–2 mg l"−"1. Around 200 samples, which consisted of laboratory prepared as well as field samples collected from different locations in Karnataka, India, were tested with Akvo Caddisfly. The results showed a significant positive correlation between Ion Selective Electrode (ISE) method and Akvo Caddisfly (Phones A, B and C), with correlation coefficient ranging between 0.9952 and 1.000. In addition, there was no significant difference in the mean fluoride content values between ISE and Phone B and C except for Phone A. Thus the smartphone method is economical and suited for groundwater fluoride analysis in the field. - Highlights: • Fluoride is an inorganic pollutant in ground water, affecting human health. • A colorimetric method for measurement of fluoride in drinking water with smartphone • Measurement is by mixing water with zirconyl xylenol orange complex reagent. • Results are comparable with laboratory-based ion selective fluoride electrode method.

Monitoring of fluoride in water samples using a smartphone

Energy Technology Data Exchange (ETDEWEB)

Levin, Saurabh [Akvo Foundation (Netherlands); Krishnan, Sunderrajan [INREM Foundation (India); Rajkumar, Samuel; Halery, Nischal; Balkunde, Pradeep [Akvo Foundation (Netherlands)

2016-05-01

In several parts of India, groundwater is the only reliable, year round source for drinking water. Prevention of fluorosis, a chronic disease resulting from excess intake of fluoride, requires the screening of all groundwater sources for fluoride in endemic areas. In this paper, the authors present a field deployable colorimetric analyzer based on an inexpensive smartphone embedded with digital camera for taking photograph of the colored solution as well as an easy-fit, and compact sample chamber (Akvo Caddisfly). Phones marketed by different smartphone makers were used. Commercially available zirconium xylenol orange reagent was used for determining fluoride concentration. A software program was developed to use with the phone for recording and analyzing the RGB color of the picture. Linear range for fluoride estimation was 0–2 mg l{sup −1}. Around 200 samples, which consisted of laboratory prepared as well as field samples collected from different locations in Karnataka, India, were tested with Akvo Caddisfly. The results showed a significant positive correlation between Ion Selective Electrode (ISE) method and Akvo Caddisfly (Phones A, B and C), with correlation coefficient ranging between 0.9952 and 1.000. In addition, there was no significant difference in the mean fluoride content values between ISE and Phone B and C except for Phone A. Thus the smartphone method is economical and suited for groundwater fluoride analysis in the field. - Highlights: • Fluoride is an inorganic pollutant in ground water, affecting human health. • A colorimetric method for measurement of fluoride in drinking water with smartphone • Measurement is by mixing water with zirconyl xylenol orange complex reagent. • Results are comparable with laboratory-based ion selective fluoride electrode method.

Streptozotocin Aggravated Osteopathology and Insulin Induced Osteogenesis Through Co-treatment with Fluoride.

Science.gov (United States)

Yang, Chen; Zhang, Mengmeng; Li, Yagang; Wang, Yan; Mao, Weixian; Gao, Yuan; Xu, Hui

2015-12-01

The role of insulin in the mechanism underlying the excessive fluoride that causes skeletal lesion was studied. The in vitro bone marrow stem cells (BMSC) collected from Kunming mice were exposed to varying concentrations of fluoride with or without insulin. The cell viability and early differentiation of BMSC co-treated with fluoride and insulin were measured by using cell counting kit-8 and Gomori modified calcium-cobalt method, respectively. We further investigated the in vivo effects of varying dose of fluoride on rats co-treated with streptozotocin (STZ). Wistar rats were divided into six groups which included normal control, 10 mg fluoride/kg day group, 20 mg fluoride/kg day group, STZ control, STZ+10 mg fluoride/kg day group, and STZ+20 mg fluoride/kg day group. The rats were administered with sodium fluoride (NaF) by gavage with water at doses 10 and 20 mg fluoride/kg day for 2 months. In a period of one month, half of rats in every group were treated with streptozotocin (STZ) once through intraperitoneal injection at 52 mg/kg body weight. The serum glucose, HbA1c, and insulin were determined. Bone mineral content and insulin release were assessed. The results showed insulin combined with fluoride stimulated BMSC cell viability in vitro. The bone mineral content reduced in rats treated with higher dose of fluoride and decreased immensely in rat co-treated with fluoride and STZ. Similarly, a combination treatment of a high dose of fluoride and STZ decreased insulin sensitivity and activity. To sum up, these data indicated fluoride influenced insulin release, activity, and sensitivity. Furthermore, the insulin state in vivo interfered in the osteogenesis in turn and implied there was a close relation between insulin and bone pathogenesis in the mechanism of fluoride toxicity.

Fluorides in groundwater and its impact on health.

Science.gov (United States)

Shailaja, K; Johnson, Mary Esther Cynthia

2007-04-01

Fluoride is a naturally occurring toxic mineral present in drinking water and causes yellowing of teeth, tooth problems etc. Fluorspar, Cryolite and Fluorapatite are the naturally occurring minerals, from which fluoride finds its path to groundwater through infiltration. In the present study two groundwater samples, Station I and Station II at Hyderabad megacity, the capital of Andhra Pradesh were investigated for one year from January 2001 to December 2001. The average fluoride values were 1.37 mg/l at Station I and 0.91 mg/l at Station II. The permissible limit given by BIS (1983) 0.6-1.2 mg/l and WHO (1984) 1.5 mg/l for fluoride in drinking water. The groundwaters at Station I exceeded the limit while at Station II it was within the limits. The study indicated that fluoride content of 0.5 mg/l is sufficient to cause yellowing of teeth and dental problems.

Distribution coefficients for plutonium and americium on particulates in aquatic environments

International Nuclear Information System (INIS)

Sanchez, A.L.; Schell, W.R.; Sibley, T.H.

1982-01-01

The distribution coefficients of two transuranic elements, plutonium and americium, were measured experimentally in laboratory systems of selected freshwater, estuarine, and marine environments. Gamma-ray emitting isotopes of these radionuclides, 237 Pu and 241 Am, were significantly greater than the sorption Ksub(d) values, suggesting some irreversibility in the sorption of these radionuclides onto sediments. The effects of pH and of sediment concentration on the distribution coefficients were also investigated. There were significant changes in the Ksub(d) values as these parameters were varied. Experiments using sterilized and nonsterilized samples for some of the sediment/water systems indicate possible bacterial effects on Ksub(d) values. (author)

A health risk assessment for fluoride in Central Europe.

Science.gov (United States)

Fordyce, F M; Vrana, K; Zhovinsky, E; Povoroznuk, V; Toth, G; Hope, B C; Iljinsky, U; Baker, J

2007-04-01

Like many elements, fluorine (which generally occurs in nature as fluoride) is beneficial to human health in trace amounts, but can be toxic in excess. The links between low intakes of fluoride and dental protection are well known; however, fluoride is a powerful calcium-seeking element and can interfere with the calcified structure of bones and teeth in the human body at higher concentrations causing dental or skeletal fluorosis. One of the main exposure routes is via drinking water and the World Health Organisation currently sets water quality guidelines for the element. In Central Europe, groundwater resources that exceed the guideline value of 1.5 mg l-1 are widespread and effects on health of high fluoride in water have been reported. The aim of the current project was to develop a geographic information system (GIS) to aid the identification of areas where high-fluoride waters and fluorosis may be a problem; hence, where water treatment technologies should be targeted. The development of the GIS was based upon the collation and digitisation of existing information relevant to fluoride risk in Ukraine, Moldova, Hungary and Slovakia assembled for the first time in a readily accessible form. In addition, geochemistry and health studies to examine in more detail the relationships between high-fluoride drinking waters and health effects in the population were carried out in Moldova and Ukraine demonstrating dental fluorosis prevalence rates of 60-90% in adolescents consuming water containing 2-7 mg l-1 fluoride.

Occurrence of fluoride in ground waters of Saudi Arabia

Science.gov (United States)

Alabdulaaly, Abdulrahman I.; Al-Zarah, Abdullah I.; Khan, Mujahid A.

2013-09-01

The presence of elevated levels of fluoride in groundwater is considered a global problem. Fluoride in water derives mainly from dissolution of natural minerals in the rocks and soils with which water interacts. The most common fluorine-bearing minerals are fluorite, apatite and micas. Anthropogenic sources of fluoride include agricultural fertilizers and combustion of coal. In the present research, a survey of wells ( n = 1,060) was undertaken in all the 13 regions of the Kingdom of Saudi Arabia to assess the contained fluoride (F) levels. The results indicated variation in fluoride levels from 0.10 to 5.4 mg/L as F throughout the kingdom. The average fluoride levels in milligrams per liter as F were as follows in descending order: 1.80 (Hadwood Shamalyah), 1.37 (Hail), 1.33 (Eastern Province), 1.16 (Al Jouf), 1.11 (Qassim), 1.01 (Riyadh), 0.90 (Madina Al Munnawara), 0.81 (Tabouk), 0.74 (Makkah Al- Mukaramma), 0.73 (Jizan), 0.66 (Asir), 0.64 (Najran), and 0.60 (Al Baha). The results indicated that fluoride levels exceeded the USEPA maximum contaminant limits for drinking water (4 mg/L) in several wells ( n = 7) in different regions of the kingdom and that 13.96 % of the wells exceeded the World Health Organization recommended levels (1.5 mg/L). The results were also compared with the secondary USEPA contaminant standards of 2.0 mg/L for fluorides.

Biochemical studies on the effect of fluoride on higher plants. II. The effect of fluoride on sucrose-synthesizing enzymes from higher plants

Energy Technology Data Exchange (ETDEWEB)

Yang, S F; Miller, G W

1963-01-01

A study was initiated to characterize the properties of partially purified phosphoglucomutase, uridine diphosphate glucose pyrophosphorylase and uridine diphosphate glucose-fructose transglucosyalse, from various plant sources, with respect to activation by metal ions and inhibition by fluoride. Of the three enzymes studied, only phosphoglucomutase was very sensitive to fluoride. It is likely that the inhibition of sucrose synthesis in fluoride-fumigated plants might be due to the inhibition of phosphoglucomutase, which plays an important role in carbohydrate metabolism. However, at present, there is insufficient evidence to show the inhibition of phosphoglucomutase in vivo by fumigation with hydrogen fluoride.

Fluoride removal from aqueous solution by pumice: case study on ...

African Journals Online (AJOL)

EJIRO

conditions, the fluoride removal efficiency from Kuhbonan water by 2.8 mg/L fluoride was 74.64%. Eventually ... industrial wastewater containing fluoride is a key ..... solution using silica ceramic: Adsorption kinetics and equilibrium studies.

Controlling the fluoride dosage in a patient with compromised salivary function.

Science.gov (United States)

Eichmiller, Frederick C; Eidelman, Naomi; Carey, Clifton M

2005-01-01

High-concentration topical fluorides are used commonly to with compromised salivary function due to irradiation and chemotherapy. The authors describe a 50-year-old man with previously treated cancer who was using tray-applied topical fluoride gel. He complained of gastric symptoms, difficulty in swallowing, leg muscle soreness and knee joint soreness. A computed tomographic scan revealed thickening of the esophageal walls. An upper endoscopy revealed abnormal motility. The motility test indicated high-amplitude peristalsis and hypertensive lower esophageal sphincter, and urine testing indicated high levels of systemic fluoride. The patient's fluoride regimen was altered, and within a short period his urinary fluoride levels returned to normal and his symptoms resolved. Clinicians prescribing home-applied high-concentration fluorides need to be cognizant of the symptoms of fluoride toxicity, carefully monitor the patient's compliance with the treatment regimen, and adjust the dosage or mode of application to control the total ingested dose of fluoride.

Chronic Fluoride Toxicity: Dental Fluorosis

OpenAIRE

DenBesten, Pamela; Li, Wu

2011-01-01

Dental fluorosis occurs as a result of excess fluoride ingestion during tooth formation. Enamel fluorosis and primary dentin fluorosis can only occur when teeth are forming, and therefore fluoride exposure (as it relates to dental fluorosis) occurs during childhood. In the permanent dentition, this would begin with the lower incisors, which complete mineralization at approximately 2–3 years of age, and end after mineralization of the third molars. The white opaque appearance of fluorosed enam...

Fluoride content and labelling of toothpastes marketed in India.

Science.gov (United States)

Thakkar, V P; Rao, A; Rajesh, G; Shenoy, R; Pai, M

2015-09-01

To enumerate the fluoride content and labelling practices of toothpastes marketed in India and to determine if the content is in accordance with the information provided on the packaging. In vitro analysis of total and free available fluoride in 5 adult and 5 children's fluoride toothpastes in India using fluoride ion electrode. Information on the tube and carton was checked to assess the labelling. The mean Total Fluoride concentrations (TF) in the toothpastes labelled 1,000 ppm, 500ppm and 458 ppm were 1,000, 500 and 449mg/L (sd values 3, 5 and 4mg/L) respectively. The toothpastes' Total Soluble Fluoride (TSF) concentration was generally slightly less than the TF concentration. Overall mean percentage of TSF concentration was 94% sd 9%. The mean percentage of TSF concentration in SMFP (sodium monofluorophosphate)/CaCO3 (calcium carbonate) containing toothpastes was 86% sd 16% while that in NaF (sodium fluoride)/Si (silica) based toothpastes was 98% sd 1% and 95% sd 1% in the remaining toothpastes with unknown abrasive. NaF/Si based toothpastes had more TSF concentration than the others (plabelled following the guidelines of the regulatory body of India, 3 of the 10 failed to mention the abrasive present.

Photosynthesis of ammonium uranous fluoride

International Nuclear Information System (INIS)

El-Fekey, S.A.; Zaki, M.R.; Farah, M.Y.

1975-01-01

This study pertains to utilisation of solar energy for ethanol photosynthesis of ammonium uranous fluoride, that satisfies nuclear specifications needed for calcio- or magnesiothermy. Insolation in autumn using 4-10% ethanol in 5-20 g uranium/litre at initial pH 3.25 gave practically 99.8% yield in two hours, independant of 1.0 to 2.0 stoichiometric NH 4 F. With ultraviolet light, the yield varied between 30 and 60%, even after four hours irradiation. Stirring and heating to 60 0 C raised the tap density of the dried double fluorides from 1.48 at 30 0 C, to 1.85 g/cm 3 at 60 0 C. The texture increased also in fineness to 100% 50μ aggregates. The powders satisfy nuclear purity specifications. Thermograms indicated preferential decomposition of double fluoride at 375 0 C in controlled atmosphere to obtain nuclear pure anhydrous uranium tetrafluoride

Effect of exercise on fluoride metabolism in adult humans: a pilot study.

Science.gov (United States)

V Zohoori, Fatemeh; Innerd, Alison; Azevedo, Liane B; Whitford, Gary M; Maguire, Anne

2015-11-19

An understanding of all aspects of fluoride metabolism is critical to identify its biological effects and avoid fluoride toxicity in humans. Fluoride metabolism and subsequently its body retention may be affected by physiological responses to acute exercise. This pilot study investigated the effect of exercise on plasma fluoride concentration, urinary fluoride excretion and fluoride renal clearance following no exercise and three exercise intensity conditions in nine healthy adults after taking a 1-mg Fluoride tablet. After no, light, moderate and vigorous exercise, respectively, the mean (SD) baseline-adjusted i) plasma fluoride concentration was 9.6(6.3), 11.4(6.3), 15.6(7.7) and 14.9(10.0) ng/ml; ii) rate of urinary fluoride excretion over 0-8 h was 46(15), 44(22), 34(17) and 36(17) μg/h; and iii) rate of fluoride renal clearance was 26.5(9.0), 27.2(30.4), 13.1(20.4) and 18.3(34.9) ml/min. The observed trend of a rise in plasma fluoride concentration and decline in rate of fluoride renal clearance with increasing exercise intensity needs to be investigated in a larger trial. This study, which provides the first data on the effect of exercise with different intensities on fluoride metabolism in humans, informs sample size planning for any subsequent definitive trial, by providing a robust estimate of the variability of the effect.

An In-Vitro Study on the Release of Fluoride from Two Restorative Materials and Their Rechargeability after Exposure to Daily 1000 ppm Fluoride

Directory of Open Access Journals (Sweden)

A. Kowsari

2005-09-01

Full Text Available Statement of Problem: Since the fluoride releases from materials with the property of releasing fluoride are decreasing gradually, it seems that probably the material rechargeability is more important than their long-term fluoride release.Purpose: the objective of this study was to asses the fluoride release and rechargeability of 2 types of fluoride releasing restorative materials, a resin modified glass ionomer(Vitremer and a compomer (Compoglass F, after exposure to daily NaF solutionscontaining 1000 ppm F, for 1 minute.Materials and Methods: Twelve discs ( 8 mm ×2 mm of each of the materials were fabricated, and divided into 2 groups (test and control. All discs were stored in 4 mL artificial saliva at 37°C. In group 1 (N=6, the specimens were immersed in artificialsaliva which was changed daily for 25 days. In group 2 (N=6, in addition to receiving the same treatment as group 1, the specimens were immersed in NaF solution (1000ppm F, ph=6.9 for 1 minute before daily saliva change. A potentiometer was used to determine the amount of fluoride released on days 1, 2, 3, 5, 10, 15, 20 and 25, after the daily saliva change, in all study groups. Data were analyzed by the t-student test after confirmation of the equality of variances by Leven’s test.Results: Both materials continued releasing fluoride throughout the whole study period. For each material, the release was highest on day one. During the first 3 days,glass ionomer released significantly higher amounts of fluoride as compared to compomer (p0.05. After exposure to NaF solution, none of the materials showed statistically significant rechargeability (p>0.05 and the amount of fluoride-releasecontinued to drop during the study period in similar patterns for both the test and the control groups.Conclusion: It may be concluded that rechargeability of glass ionomer and compomer,using daily neutral fluoride mouth rinses and toothpastes does not occur in reliable amounts.

A Comparison of Fluoride Uptake by Sound Enamel Following Application of Sodium Fluoride Mouthrinses and APF Gels Produced in Iran with Standardized Foreign Samples

Directory of Open Access Journals (Sweden)

A Kowsari

2002-02-01

Full Text Available The goal of this investigation is to compare the extent of fluoride uptake by sound enamel following application of two commercial mouthrinses containing sodium fluoride (0.2% and a topical gel containing APF (1.23% produced in Iran with those of foreign standardized ones. Sixty extracted premolars were used. Each tooth was divided into two lingual and buccal halves, one half as control, the other one as experimental. Enamel biopsy technique (two- step acid etching was used to determine the concentration of fluoride and calcium in each sample. For data comparison and fluoride uptake estimation, the depths of layers with the use of linear regression analysis were standardized to 25 and 50um. The analysis showed that in Iranian mouthrinse no. 1, there is linear correlation between fluoride concentration and enamel depth, in both control and experimental group at the first and second layers, while, in other groups, this correlation was observed just at the first layer (superficial enamel layer. The greatest fluoride uptake was seen at Iranian mouthrinse no.2 and the least was seen at foreign mouthrinse no. 3. From among two APF gels, the greatest uptake was observed at gel no. 1 (Iranian. The results showed that all three Iranian products increase fluoride content of enamel, moreover the level of fluoride uptake, while applying Iranian products, in comparison with foreign ones, shows considerable increase.

Fluoride removal from diluted solutions by Donnan dialysis using full factorial design

Energy Technology Data Exchange (ETDEWEB)

Boubakri, Ali; Helali, Nawel; Tlili, Mohamed; Amor, Mohamed Ben [Center of Researches and Water Technologies, Soliman (Turkey)

2014-03-15

Excessive fluoride concentration in potable water can lead to fluorosis of teeth and bones. In the present study, Donnan dialysis (DD) is applied for the removal of fluoride ions from diluted sodium fluoride solutions. A four factor two level (2{sup 4}) full factorial design was used to investigate the influence of different physico-chemical parameters on fluoride removal efficiency (Y{sub F}) and fluoride flux (J{sub F}) through anion exchange membrane. The statistical design determines factors which have the important effects on Donnan dialysis performance and studies all interactions among the considered parameters. The four significant factors were initial fluoride concentration, feed flow rate, temperature and agitation speed. The experimental results and statistical analysis show that the temperature and agitation speed have positive effects on fluoride removal efficiency and the initial fluoride concentration has a negative effect. In the case of fluoride flux, feed flow rate and initial concentration are the main effect and all factors have a positive effect. The interaction between studied parameters was not negligible on two responses. A maximum fluoride removal of 75.52% was obtained under optimum conditions and the highest value of fluoride flux obtained was 2.4 mg/cm{sup 2}·h. Empirical regression models were also obtained and used to predict the flux and the fluoride removal profiles with satisfactory results.

Performance of novel hydroxyapatite nanowires in treatment of fluoride contaminated water.

Science.gov (United States)

He, Junyong; Zhang, Kaisheng; Wu, Shibiao; Cai, Xingguo; Chen, Kai; Li, Yulian; Sun, Bai; Jia, Yong; Meng, Fanli; Jin, Zhen; Kong, Lingtao; Liu, Jinhuai

2016-02-13

Novel ultralong hydroxyapatite (HAP) nanowires were successfully prepared for fluoride removal for the first time. The fluoride adsorption on the HAP nanowires was studied on a batch mode. The results revealed that the adsorption data could be well described by the Freundlich model, and the adsorption kinetic followed the pseudo-second-order model. The maximum of adsorption capacity was 40.65 mg/g at pH 7.0 when the fluoride concentration is 200mg/L. The thermodynamic parameters suggested that the adsorption of fluoride was a spontaneous endothermic process. The FT-IR, XPS and Zeta potential analysis revealed that both anion exchange and electrostatic interactions were involved in the adsorption of fluoride. Furthermore, the HAP nanowires were made into HAP membrane through a simple process of suction filtration. Membrane filtration experiments revealed that the fluoride removal capabilities depended on the membrane thickness, flow rate and initial concentration of fluoride. The as-prepared membrane could remove fluoride efficiently through continues filtration. The filtered water amount could reach 350, 192, and 64 L/m(2) when the fluoride concentrations were 4, 5 and 8 ppm, respectively, using the HAP membrane with only 150 μm thickness. The as-synthesized ultralong HAP nanowires were thus demonstrated to be very effective and biocompatible adsorbents for fluoride removal from contaminated water. Copyright © 2015 Elsevier B.V. All rights reserved.

An experimental study of americium-241 biokinetics in the Lobster Homarus Gammarus. Analysis of the accumulation/storage and detoxification processes at the subcellular level

International Nuclear Information System (INIS)

Paquet, F.

1993-01-01

An experimental study of americium-241 kinetics has been conducted in the lobster Homarus gammmarus. The investigations were conducted at all the levels from the whole body to the subcellular and molecular levels. The animals were contaminated by a single or chronic ingestion of 241 Am labelled mussels. Assessments of accumulation, elimination and distribution of the radionuclide were established on organisms kept in the laboratory; they made it possible to demonstrate the importance of the digestive gland in the radionuclide transfer pathways. The preliminary results led to structural then ultrastructural investigations of the digestive gland in association with radioautographic studies and cellular extractions methods. Four cellular types were demonstrated, only two of them being implied in the radionuclide retention, the former being responsible for americium intake and the latter for its long-term retention. By means of biochemical techniques, subcellular accumulation was studied and the organelles implied in the nuclide retention were specified. Finally, a method of cellular nuclei dissociation was developed; it made it possible to analyse the molecular nature of americium ligands and to demonstrate the function of the protein nuclear matrix in the nuclide retention

Solvents effects on electrochemical characteristics of graphite fluoride-lithium batteries

Energy Technology Data Exchange (ETDEWEB)

Nobuatsu, W.; Hidekazu, T.; Rika, H.; Tsuyoshi, N.

1982-11-01

A study was made of the electrochemical characteristics of graphite fluoride-lithium batteries in various non-aqueous solvents. Two types of graphite fluorides (C/sub 2/F) /SUB n/ and (CF) /SUB n/ were used as cathode materials. The discharge characteristics of graphite fluorides were better in dimethylsulfoxide, ..gamma..-butyrolactone, propylene carbonate and sulfolane in that order. The relation between electrod potential of graphite fluoride and solvation energy of lithium ion with each solvent indicates that solvated lithium ion is intercalated into graphite fluoride layers by the electrode reaction. Both the difference in the overpotentials and in the rates of OCV recovery among these solvents further supports the proposed reaction mechanism.

Mie scattering in heavy-metal fluoride glasses

International Nuclear Information System (INIS)

Edgar, A.

1996-01-01

Heavy-metal fluoride glasses comprise mixtures of heavy-cation fluorides such as those of zirconium, barium, and lanthanum together with some stabilising fluorides such as AlF 3 . For particular relative proportions, the mixtures form a glass rather than a polycrystalline material when quenched from the melt. The particularly useful features of these glasses are the wide spectral region (∼200nm-8000nm) over which they are transparent, the low minimum attenuation at the centre of the spectral window, and the ease with which optically-active rare-earth ions can be incorporated, leading to potential applications in passive and active fibre optics. The minimal attenuation, which is potentially lower than for silica fibre, is generally limited by wavelength-independent scattering by particle and gas bubble inclusions. We have observed a new wavelength-dependent scattering effect in fluoride glass of the well-known composition ZLABN20. In this paper, we report on work in progress on the optical extinction and scattering spectrum of the fluoride glasses, and discuss the spectra in terms of Mie's scattering theory. The chemical nature of the scattering centres in these nominally 'pure' glasses is at present a puzzle, and relative merits of various possible models will be compared

Fluoride levels in commercially available rice in Ethiopia | Tegegne ...

African Journals Online (AJOL)

Alkaline fusion was used for sample preparation of six varieties for both the raw rice and rice cooked with tap water and fluoridated water. Fluoride levels ranged from 0.1-5.5 mg/kg in raw rice sample. Rice which was cooked with different fluoride levels of water showed increment depending on the method of cooking.

Effect of fluoride addition on the properties of dental alginate impression materials.

Science.gov (United States)

Lee, Yong-Keun; Lim, Bum-Soon; Kim, Cheol-We

2004-03-01

Fluoride-containing dental alginate impression materials can exert a considerable reduction in enamel solubility. The objective was to evaluate the effects of fluoride addition in the alginate impression materials on the properties and subsequent release of fluoride. Four experimental alginate impression materials were studied. Materials were mixed with distilled water (control) or 100-ppm fluoride solution. One or two percent NaF, or 1% SnF2 was added to the materials, which were mixed with distilled water. Fluoride release, flexibility, recovery from deformation, setting time, compressive strength and elastic modulus were determined in accordance with the ISO 1563 and ANSI/ADA Spec. 18. Fluoride release increased after addition of fluoride, and the released amount was 0.762-14.761 ppm. Addition of NaF or SnF2 resulted in higher fluoride release than the control group (p alginate impression material may result in effective release of fluoride without deteriorating the properties of material itself.

Sirtuin1 and autophagy protect cells from fluoride-induced cell stress

Science.gov (United States)

Suzuki, Maiko; Bartlett, John D.

2014-01-01

Sirtuin1 (SIRT1) is an (NAD+)-dependent deacetylase functioning in the regulation of metabolism, cell survival and organismal lifespan. Active SIRT1 regulates autophagy during cell stress, including calorie restriction, endoplasmic reticulum stress and oxidative stress. Previously, we reported that fluoride induces endoplasmic reticulum (ER) stress in ameloblasts responsible for enamel formation, suggesting that ER-stress plays a role in dental fluorosis. However, the molecular mechanism of how cells respond to fluoride-induced cell stress is unclear. Here, we demonstrate that fluoride activates SIRT1 and initiates autophagy to protect cells from fluoride exposure. Fluoride treatment of ameloblast-derived cells (LS8) significantly increased Sirt1 expression and induced SIRT1 phosphorylation resulting in the augmentation of SIRT1 deacetylase activity. To demonstrate that fluoride exposure initiates autophagy, we characterized the expression of autophagy related genes (Atg); Atg5, Atg7 and Atg8/LC3 and showed that both their transcript and protein levels were significantly increased following fluoride treatment. To confirm that SIRT1 plays a protective role in fluoride toxicity, we used resveratrol (RES) to augmented SIRT1 activity in fluoride treated LS8 cells. RES increased autophagy, inhibited apoptosis, and decreased fluoride cytotoxicity. Rats treated with fluoride (0, 50 and 100 ppm) in drinking water for 6 weeks had significantly elevated expression levels of Sirt1, Atg5, Atg7 and Atg8/LC3 in their maturation stage enamel organs. Increased protein levels of p-SIRT1, ATG5 and ATG8/LC3 were present in fluoride-treated rat maturation stage ameloblasts. Therefore, the SIRT1/autophagy pathway may play a critical role as a protective response to help prevent dental fluorosis. PMID:24296261

Sirtuin1 and autophagy protect cells from fluoride-induced cell stress.

Science.gov (United States)

Suzuki, Maiko; Bartlett, John D

2014-02-01

Sirtuin1 (SIRT1) is a nicotinamide adenine dinucleotide (NAD(+))-dependent deacetylase functioning in the regulation of metabolism, cell survival and organismal lifespan. Active SIRT1 regulates autophagy during cell stress, including calorie restriction, endoplasmic reticulum (ER) stress and oxidative stress. Previously, we reported that fluoride induces ER-stress in ameloblasts responsible for enamel formation, suggesting that ER-stress plays a role in dental fluorosis. However, the molecular mechanism of how cells respond to fluoride-induced cell stress is unclear. Here, we demonstrate that fluoride activates SIRT1 and initiates autophagy to protect cells from fluoride exposure. Fluoride treatment of ameloblast-derived cells (LS8) significantly increased Sirt1 expression and induced SIRT1 phosphorylation resulting in the augmentation of SIRT1 deacetylase activity. To demonstrate that fluoride exposure initiates autophagy, we characterized the expression of autophagy related genes (Atg); Atg5, Atg7 and Atg8/LC3 and showed that both their transcript and protein levels were significantly increased following fluoride treatment. To confirm that SIRT1 plays a protective role in fluoride toxicity, we used resveratrol (RES) to augment SIRT1 activity in fluoride treated LS8 cells. RES increased autophagy, inhibited apoptosis, and decreased fluoride cytotoxicity. Rats treated with fluoride (0, 50, 100 and 125ppm) in drinking water for 6weeks had significantly elevated expression levels of Sirt1, Atg5, Atg7 and Atg8/LC3 in their maturation stage enamel organs. Increased protein levels of p-SIRT1, ATG5 and ATG8/LC3 were present in fluoride-treated rat maturation stage ameloblasts. Therefore, the SIRT1/autophagy pathway may play a critical role as a protective response to help prevent dental fluorosis. Copyright © 2013 Elsevier B.V. All rights reserved.

Correlation among fluoride and metals in irrigation water and soils of ...

African Journals Online (AJOL)

Correlation among fluoride and metals in irrigation water and soils of Ethiopian Rift Valley. ... The fluoride concentrations in water samples were found in the range of 0.14-8.0 mg/L which is below the WHO limit of fluoride concentration for irrigation (less than 10 mg/L). ... KEY WORDS: Fluoride, Metals, Water, Soil, Ethiopia.

Diffusion of fluoride in bovine enamel

International Nuclear Information System (INIS)

Flim, G.J.; Arends, J.; Kolar, Z.

1976-01-01

The uptake of 18 F and the penetration of both F and 18 F in bovine enamel was investigated. Sodium fluoride solutions buffered at pH 7 were employed. The uptake of 18 F was measured by a method described by R. Duckworth and M. Braden, Archs. Oral. Biol., 12(1967), pp. 217-230. The penetration concentration profiles of fluoride (F, 18 F) in the enamel were measured by a sectioning technique. The 18 F uptake in enamel was proportional to approximately tsup(3/4); t being the uptake time. The 18 F concentration as a function of the position in the enamel can be described by: c*(x,t) = c 0 *(t)exp[-α*(t)x]. After correction for the initial fluoride concentration in enamel, for unlabelled fluoride the same dependency is obtained. A model based on simultaneous diffusion and chemical reaction in the pores and diffusion into the hydroxyapatite crystallites will be presented. The results show that diffusion coefficients of the pores are approximately equal to 10 -10 cm 2 s -1 and in the apatite crystallites approximately equal to 10 -17 cm 2 s -1 . The limitations and the approximations of the model are discussed

Chemico-therapeutic approach to prevention of dental caries. [using stannous fluoride gel

Science.gov (United States)

Shannon, I. L.

1975-01-01

The program of chemical preventive dentistry is based primarily upon the development of a procedure for stabilizing stannous fluoride in solution by forcing it into glycerin. New topical fluoride treatment concentrates, fluoride containing gels and prophylaxis pastes, as well as a completely stable stannous fluoride dentifrice are made possible by the development of a rather complicated heat application method to force stannous fluoride into solution in glycerin. That the stannous fluoride is clinically effective in such a preparation is demonstrated briefly on orthodontic patients.

Press forging and optical properties of lithium fluoride

Science.gov (United States)

Ready, J. F.; Vora, H.

1980-07-01

Lithium fluoride is an important candidate material for windows on high power, short-pulse ultraviolet and visible lasers. Lithium fluoride crystals were press forged in one step over the temperature range 300 to 600 C to obtain fine grained polycrystalline material with improved mechanical properties. The deformation that can be given to a lithium fluoride crystal during forging is limited by the formation of internal cloudiness (veiling) with the deformation limit increasing with increasing forging temperature from about 40 percent at 400 C to 65 percent at 600 C. To suppress veiling, lithium fluoride crystals were forged in two steps over the temperature range 300 to 600 C, to total deformations of 69 to 76 percent, with intermediate annealing at 700 C. This technique yields a material which has lower scattering with more homogeneous microstructure than that obtained in one step forging. The results of characterization of various optical and mechanical properties of single crystal and forged lithium fluoride, including scattering, optical homogeneity, residual absorption, damage thresholds, environmental stability, and thresholds for microyield are described.

Press forging and optical properties of lithium fluoride

International Nuclear Information System (INIS)

Ready, J.F.; Vora, H.

1979-01-01

Lithium fluoride is an important candidate material for windows on high-power, short-pulse ultraviolet and visible lasers. Lithium fluoride crystals have been press forged in one step over the temperature range 300 to 600 0 c to obtain fine-grained polycrystalline material with improved mechanical properties. The deformation that can be given to a lithium fluoride crystal during forging is limited by the formation of internal cloudiness (veiling) with the deformation limit increasing with increasing forging temperature from about 40% at 400 0 C to 65% at 600 0 C. To suppress veiling, lithium fluoride crystals were forged in two steps over the temperature range 300 to 600 0 C, to total deformations of 69-76%, with intermediate annealing at 700 0 C. This technique yields a material which has lower scattering with more homogeneous microstructure than that obtained in one-step forging. The results of characterization of various optical and mechanical properties of single-crystal and forged lithium fluoride, including scattering, optical homogeneity, residual absorption, damage thresholds, environmental stability, and thresholds for microyield are described

Effects of fluorides on plants

Energy Technology Data Exchange (ETDEWEB)

Yamazoe, F

1975-11-01

Fluorine compounds known to be air pollutants, such as hydrogen fluoride and silicon tetrachloride, are highly poisonous to plants even at ppm - ppb levels. As solid microparticles, acidic sodium fluoride and cryolite cause problems by adhering to plant leaves and absorbing into plant bodies. Plants are classified by their susceptibility to hydrogen fluoride: gladiolus, apricot, buckwheat, turnip and Vaccinium vitis-idaea are most susceptible showing slight injury at less than 5 ppb for 7-9 days; maize, pepper, and dahlia are fairly susceptible, followed by azalea, rose, lilac, and alfalfa, then by oak and tomato. Gladiolus is used as an indicator plant. The exposure factor for one species was known. The symptoms of plants exposed to gaseous fluorine compounds are described in detail at various concentrations. The causal mechanism of the injuries due to fluorine compounds is described in detail, with the method of determining the fluorine content of plant parts. 7 references.

SBIR-Long fluoride fiber

Science.gov (United States)

Jaeger, Raymond E.; Vacha, Lubos J.

1987-08-01

This report summarizes results obtained under a program aimed at developing new techniques for fabricating long lengths of heavy metal fluoride glass (HMFG) optical fiber. A new method for overcladding conventional HMFG preforms with a low melting oxide glass was developed, and improvements in the rotational casting method were made to increase preform length. The resulting composite glass canes consist of a fluoride glass overcoat layer to enhance strength and chemical durability. To show feasibility, prototype optical fiber preforms up to 1.6 cm in diameter with lengths of 22 cm were fabricated. These were drawn into optical fibers with lengths up to 900 meters.

Measurements of. alpha. -emitting plutonium and americium in the intertidal sands of west Cumbria, UK

Energy Technology Data Exchange (ETDEWEB)

Eakins, J.D.; Morgan, A.; Baston, G.M.N.; Pratley, F.W.; Strange, L.P.; Burton, P.J. (UKAEA Harwell Lab. (UK). Environmental and Medical Science Div.)

1990-01-01

Samples of surface sand and sand cores were collected from intertidal regions of west Cumbria between Silloth and Walney Island (including the Duddon Estuary) between 1982 and 1984 and analysed for {sup 238}Pu, {sup 239+240}Pu and {sup 241}Am. Generally, more than 95% of the {alpha}-emitting transuranic nuclides were associated with the sand and less than 5% with entrained silt. The greatest concentrations of both plutonium and americium were found at Braystones. Concentrations declined with distance from the Sellafield Works. The largest actinide deposits occurred at Drigg (320 and 720 kBq m{sup -2} of {sup 239+240}Pu and {sup 241}Am respectively). The integrated deposits in intertidal sand between Silloth and Walney Island were about 4.2 and 7.0 TBq respectively, which represent about 1% of the total {alpha}-emitting activity discharged to sea from Sellafield Works up to 1982. The corresponding value for the Duddon Estuary is about 0.3%. Only on beaches close to Sellafield did levels of man-made {alpha}-emitters exceed those of natural {alpha}-emitting nuclides. The radiological consequences of the intertidal inventory of plutonium and americium are shown to be very small and much less than from the seafood pathway. (author).

IMPACT OF FLUORIDE ON DENTAL HEALTH QUALITY.

Science.gov (United States)

Medjedovic, Eida; Medjedovic, Senad; Deljo, Dervis; Sukalo, Aziz

2015-12-01

Fluoride is natural element that strengthens teeth and prevents their decay. Experts believe that the best way to prevent cavities is the use of fluoride from multiple sources. Studies even show that in some cases, fluoride can stop already started damage of the teeth. In children younger than 6 years fluoride is incorporated into the enamel of permanent teeth, making the teeth more resistant to the action of bacterial and acids in food. The aim of this study is to determine the effects of improving the health status of teeth after six months treatment with the use of topical fluoridation 0.5% NaF, and the level and quality of the impact of treatment with chemical 0.5% NaF on the dental health of children at age from 8 to 15 years, in relation to gender and chronological age. This study included school children aged 8 to 15 years who visited health and dental services dependent in Mostar. It is obvious that after the implementation of treatment with 5% NaF by the method of topical fluoridation, health status of subjects from the experimental group significantly improved, so that at the final review 89.71% or 61 subjects of the experimental group had healthy (cured teeth), tooth with dental caries only 5.88% or 4 respondents tooth with dental caries and filling 4.41% or 3 respondents, extracted baby tooth 14.71% or 10 respondents, while for 13.24% of respondents was identified state with still unerupted teeth. Our findings are indirectly confirmed that the six-month treatment of fluoridation with 5% NaF, contributed to statistically significant improvement in overall oral health of the experimental group compared to the control group which was not treated by any dental treatment. It can be concluded that there is a statistically significant difference in the evaluated parameters of oral health of children in the control group compared to the studied parameters of oral health the experimental group of children at the final dental examination.

Determination of zirconium by fluoride ion selective electrode

International Nuclear Information System (INIS)

Mahanty, B.N.; Sonar, V.R.; Gaikwad, R.; Raul, S.; Das, D.K.; Prakash, A.; Afzal, Md.; Panakkal, J.P.

2010-01-01

Full text: Zirconium is used in a wide range of applications including nuclear clad, catalytic converters, surgical appliances, metallurgical furnaces, superconductors, ceramics, lamp filaments, anti corrosive alloys and photographical purposes. Irradiation testing of U-Zr and U-Pu-Zr fuel pins has also demonstrated their feasibility as fuel in liquid metal reactors. Different methods that are employed for the determination of zirconium are spectrophotometry, potentiometry, neutron activation analysis and mass spectrometry. Ion-selective electrode (ISE), selective to zirconium ion has been studied for the direct potentiometric measurements of zirconium ions in various samples. In the present work, an indirect method has been employed for the determination of zirconium in zirconium nitrate sample using fluoride ion selective electrode. This method is based on the addition of known excess amount of fluoride ion to react with the zirconium ion to produce zirconium tetra fluoride at about pH 2-3, followed by determination of residual fluoride ion selective electrode. The residual fluoride ion concentrations were determined from the electrode potential data using calibration plot. Subsequently, zirconium ion concentrations were determined from the concentration of consumed fluoride ions. A precision of about 2% (RSD) with the mean recovery of more than 94% has been achieved for the determination of zirconium at the concentration of 4.40 X 10 -3 moles lit -1

Influence of biofilms on migration of uranium, americium and europium in the environment

International Nuclear Information System (INIS)

Baumann, Nils; Zirnstein, Isabel; Arnold, Thuro

2015-01-01

The report on the influence of biofilms on migration of uranium, americium and europium in the environment deals with the contamination problems of uranium mines such as SDAG WISMUT in Saxonia and Thuringia. In mine waters microorganisms form a complex microbiological biocoenosis in spite of low pH values and high heavy metal concentrations including high uranium concentrations. The analyses used microbiological methods like confocal laser scanning microscopy and molecular-biological techniques. The interactions of microorganism with fluorescent radioactive heavy metal ions were performed with TRLFS (time resolved laser-induced fluorescence spectroscopy).

Fluoride caused thyroid endocrine disruption in male zebrafish (Danio rerio).

Science.gov (United States)

Jianjie, Chen; Wenjuan, Xue; Jinling, Cao; Jie, Song; Ruhui, Jia; Meiyan, Li

2016-02-01

Excessive fluoride in natural water ecosystem has the potential to detrimentally affect thyroid endocrine system, but little is known of such effects or underlying mechanisms in fish. In the present study, we evaluated the effects of fluoride on growth performance, thyroid histopathology, thyroid hormone levels, and gene expressions in the HPT axis in male zebrafish (Danio rerio) exposed to different determined concentrations of 0.1, 0.9, 2.0 and 4.1 M of fluoride to investigate the effects of fluoride on thyroid endocrine system and the potential toxic mechanisms caused by fluoride. The results indicated that the growth of the male zebrafish used in the experiments was significantly inhibited, the thyroid microtrastructure was changed, and the levels of T3 and T4 were disturbed in fluoride-exposed male fish. In addition, the expressional profiles of genes in HPT axis displayed alteration. The expressions of all studied genes were significantly increased in all fluoride-exposed male fish after exposure for 45 days. The transcriptional levels of corticotrophin-releasing hormone (CRH), thyroid-stimulating hormone (TSH), thyroglobulin (TG), sodium iodide symporter (NIS), iodothyronine I (DIO1), and thyroid hormone receptor alpha (TRα) were also elevated in all fluoride-exposed male fish after 90 days of exposure, while the inconsistent expressions were found in the mRNA of iodothyronineⅡ (DIO2), UDP glucuronosyltransferase 1 family a, b (UGT1ab), transthyretin (TTR), and thyroid hormone receptor beta (TRβ). These results demonstrated that fluoride could notably inhibit the growth of zebrafish, and significantly affect thyroid endocrine system by changing the microtrastructure of thyroid, altering thyroid hormone levels and endocrine-related gene expressions in male zebrafish. All above indicated that fluoride could pose a great threat to thyroid endocrine system, thus detrimentally affected the normal function of thyroid of male zebrafish. Copyright © 2015

Contribution of chloride channel permease to fluoride resistance in Streptococcus mutans.

Science.gov (United States)

Murata, Takatoshi; Hanada, Nobuhiro

2016-06-01

Genes encoding fluoride transporters have been identified in bacterial and archaeal species. The genome sequence of the cariogenic Streptococcus mutans bacteria suggests the presence of a putative fluoride transporter, which is referred to as a chloride channel permease. Two homologues of this gene (GenBank locus tags SMU_1290c and SMU_1289c) reside in tandem in the genome of S. mutans The aim of this study was to determine whether the chloride channel permeases contribute to fluoride resistance. We constructed SMU_1290c- and SMU_1289c-knockout S. mutans UA159 strains. We also constructed a double-knockout strain lacking both genes. SMU_1290c or SMU_1289c was transformed into a fluoride transporter- disrupted Escherichia coli strain. All bacterial strains were cultured under appropriate conditions with or without sodium fluoride, and fluoride resistance was evaluated. All three gene-knockout S. mutans strains showed lower resistance to sodium fluoride than did the wild-type strain. No significant changes in resistance to other sodium halides were recognized between the wild-type and double-knockout strains. Both SMU_1290c and SMU_1289c transformation rescued fluoride transporter-disrupted E. coli cell from fluoride toxicity. We conclude that the chloride channel permeases contribute to fluoride resistance in S. mutans. © FEMS 2016. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Influence of fluoride on aluminum toxicity to Atlantic salmon (Salmo salar)

Science.gov (United States)

Hamilton, Steven J.; Haines, Terry A.

1995-01-01

Atlantic salmon (Salmo salar) alevins were exposed to various aluminum (0–4700 μg/L) and four fluoride (0–500 μg/L) concentrations at two pH values (5.5 and 6.5) for 4- and 30-d periods. In the 4-d tests, aluminum with fluoride was less toxic at pH 6.5 than at pH 5.5, whereas without fluoride, pH had no effect. In the 30-d test, mortality in all treatments was 17–21% at pH 5.5, but only 3–7% at pH 6.5. Fish length and weight after 30 d were reduced in all fluoride–aluminum treatments at pH 5.5, but only in the 200-μg/L aluminum without fluoride treatment at pH 6.5. At pH 5.5 and 6.5 without aluminum, histomorphological examinations revealed no abnormalities in gill tissue. However, in aluminum exposure with no fluoride, gill filaments and secondary lamellae were swollen and thickened. Addition of fluoride at pH 6.5 alleviated some gill damage. At pH 5.5 and 200 μg/L aluminum, addition of 100 μg/L fluoride reduced swelling of gill lamellae, but 200 μg/L fluoride did not reduce swelling. Low fluoride concentrations (fluoride concentrations (> 100 μg/L) may not reduce aluminum-induced effects.

Histopathological Effects of Varied Fluoride Concentration on Cerebrum in Albino Rats

Directory of Open Access Journals (Sweden)

Sajad Hamid

2012-02-01

Full Text Available Fluorides have been a cause of concern for scientists and environmentalists for the long because of their harmful effects on the human and animal life but the problem was highlighted during the twentieth century because of great increase in the human population and industrialization. Since fluorides accumulate in calcified and hard tissues of the body such as bone and teeth and can be detected easily in these tissues, so most of the previous studies focused on the effects of fluorides on these tissues. However, during the past decade researchers all over the world have felt that there is a need to study the effects of fluorides on various other tissues of the body including CNS as fluoride intake for prolonged period is known to cause abnormal behavioural pattern, grave implications for Alzheimer’s Disease, Dementia, Attention deficit disorder and reduced I.Q in children as the fluorides are known to cross blood brain barrier. Hence the present study has thrown light on the involvement of brain in chronic fluoride toxicity. The target organ of studied was cerebrum. In the Study, albino rats were exposed to 30 or 100 ppm fluoride (asNaF in drinking water for 3 months. Rats exposed to 30 ppm fluoride did not show any notable alterations in brain histology, whereas rats exposed to 100 ppm fluoride showed significant neurodegenerative changes in lhe motor cortex.Changes included decrease in size and number of neurons in all the regions, signs of chromatolysis and gliosis in the motor cortex. These histological changes suggest a toxic effect of high-fluoride intake & on chronic use. [J Interdiscipl Histopathol 2012; 1(1.000: 30-34

Association of Hypertension, Body Mass Index, and Waist Circumference with Fluoride Intake; Water Drinking in Residents of Fluoride Endemic Areas, Iran.

Science.gov (United States)

Yousefi, Mahmood; Yaseri, Mehdi; Nabizadeh, Ramin; Hooshmand, Elham; Jalilzadeh, Mohsen; Mahvi, Amir Hossein; Mohammadi, Ali Akbar

2018-03-14

Hypertension is becoming a global epidemic for both rural and urban populations; it is a major public health challenge in Iran. Fluoride can be a risk factor for hypertension. Cross-sectional analysis was conducted in two study areas to assess the relation of fluoride with blood pressure prevalence, BMI, waist circumference, and waist-to-hip ratio (WHR) among different age groups in both sexes. The mean value of fluoride concentration in the drinking water from the four study villages varied from 0.68 to 10.30 mg/L. The overall prevalence of HTN and prehypertension in all subjects was 40.7%. The prevalence of isolated systolic hypertension, isolated diastolic hypertension, systolic-diastolic hypertension, and prehypertension in the total sample population was 1.15, 0.28, 9.53, and 29.76%, respectively. The odd ratio of hypertension in residents who drank water with high fluoride levels was higher than that in residents who drank water with lower level of fluoride (OR 2.3, 1.03-5.14). Logistic regression results showed that age (P water (P = 0.041) had a significant relationship with increased blood pressure. There were no statistically significant correlations between fluoride and BMI, hip circumference, and waist to hip ratio (WHR). The findings of this study are important for health care personnel and policymakers.

Urinary fluoride as a monitoring tool for assessing successful intervention in the provision of safe drinking water supply in five fluoride-affected villages in Dhar district, Madhya Pradesh, India.

Science.gov (United States)

Srikanth, R; Gautam, Anil; Jaiswal, Suresh Chandra; Singh, Pavitra

2013-03-01

Endemic fluorosis was detected in 31 villages in the Dhar district of Madhya Pradesh, Central India. Out of the 109 drinking water sources that were analyzed, about 67 % were found to contain high concentration of fluoride above the permissible level of 1.0 mg/l. Dental fluorosis among the primary school children in the age between 8 and 15 served as primary indicator for fluoride intoxication among the children. Urinary fluoride levels among the adults were found to be correlated with drinking water fluoride in 10 villages affected by fluoride. Intervention in the form of alternate safe water supply in five villages showed significant reduction in the urinary fluoride concentration when compared to the control village. Urinary fluoride serves as an excellent marker for assessing the effectiveness of intervention program in the fluoride-affected villages.

Combinatorial effects of arginine and fluoride on oral bacteria.

Science.gov (United States)

Zheng, X; Cheng, X; Wang, L; Qiu, W; Wang, S; Zhou, Y; Li, M; Li, Y; Cheng, L; Li, J; Zhou, X; Xu, X

2015-02-01

Dental caries is closely associated with the microbial disequilibrium between acidogenic/aciduric pathogens and alkali-generating commensal residents within the dental plaque. Fluoride is a widely used anticaries agent, which promotes tooth hard-tissue remineralization and suppresses bacterial activities. Recent clinical trials have shown that oral hygiene products containing both fluoride and arginine possess a greater anticaries effect compared with those containing fluoride alone, indicating synergy between fluoride and arginine in caries management. Here, we hypothesize that arginine may augment the ecological benefit of fluoride by enriching alkali-generating bacteria in the plaque biofilm and thus synergizes with fluoride in controlling dental caries. Specifically, we assessed the combinatory effects of NaF/arginine on planktonic and biofilm cultures of Streptococcus mutans, Streptococcus sanguinis, and Porphyromonas gingivalis with checkerboard microdilution assays. The optimal NaF/arginine combinations were selected, and their combinatory effects on microbial composition were further examined in single-, dual-, and 3-species biofilm using bacterial species-specific fluorescence in situ hybridization and quantitative polymerase chain reaction. We found that arginine synergized with fluoride in suppressing acidogenic S. mutans in both planktonic and biofilm cultures. In addition, the NaF/arginine combination synergistically reduced S. mutans but enriched S. sanguinis within the multispecies biofilms. More importantly, the optimal combination of NaF/arginine maintained a "streptococcal pressure" against the potential growth of oral anaerobe P. gingivalis within the alkalized biofilm. Taken together, we conclude that the combinatory application of fluoride and arginine has a potential synergistic effect in maintaining a healthy oral microbial equilibrium and thus represents a promising ecological approach to caries management. © International & American

Haematological evaluation of sodium fluoride toxicity in oryctolagus cunniculus

Directory of Open Access Journals (Sweden)

Maryam Abbas

Full Text Available Blood is promptly affected by environmental pollutants and toxicants that can cause many metabolic disorders. The high level of fluoride acts as a potential pollutant, insecticide and rodenticide with very high toxicity, associated with the hematological damage. This study aimed to determine the toxicity of Sodium Fluoride on hematological parameters in Oryctolagus cunniculus. Twenty rabbits were acclimatized and divided in to control group and three experimental groups.Experimental group-I, II and III were treated with 10, 30 and 50 mg/kg body weight doses of Sodium Fluoride orally. Various blood parameters such as TEC, Hb, HCT, MCV, MCH, MCHC, TLC and PLT count were investigated. Result findings showed that values of blood indices in experimental groups were significantly lower than the control group. Oneway ANOVA was applied for statistical analysis. The outcomes of the current studies indicated the reduction in RBC counts (anemia, leukocyte count (leukocytopenia, monocytosis, eosinopenia, neutrophilia and thrombocytosis on fluoride intoxication. Hematological disruptions like microcytic hypochromic anemia and decreased leukocyte count may be linked to the inflammatory effects of Sodium Fluoride on lymphatic organs. Keywords: Fluoride intoxication, Hypochromic anemia, Hematological, Parameters, Leukocyte alterations, Fluorosis

Probability of foliar injury for Acer sp. based on foliar fluoride concentrations.

Science.gov (United States)

McDonough, Andrew M; Dixon, Murray J; Terry, Debbie T; Todd, Aaron K; Luciani, Michael A; Williamson, Michele L; Roszak, Danuta S; Farias, Kim A

2016-12-01

Fluoride is considered one of the most phytotoxic elements to plants, and indicative fluoride injury has been associated over a wide range of foliar fluoride concentrations. The aim of this study was to determine the probability of indicative foliar fluoride injury based on Acer sp. foliar fluoride concentrations using a logistic regression model. Foliage from Acer nedundo, Acer saccharinum, Acer saccharum and Acer platanoides was collected along a distance gradient from three separate brick manufacturing facilities in southern Ontario as part of a long-term monitoring programme between 1995 and 2014. Hydrogen fluoride is the major emission source associated with the manufacturing facilities resulting with highly elevated foliar fluoride close to the facilities and decreasing with distance. Consistent with other studies, indicative fluoride injury was observed over a wide range of foliar concentrations (9.9-480.0 μg F -  g -1 ). The logistic regression model was statistically significant for the Acer sp. group, A. negundo and A. saccharinum; consequently, A. negundo being the most sensitive species among the group. In addition, A. saccharum and A. platanoides were not statistically significant within the model. We are unaware of published foliar fluoride values for Acer sp. within Canada, and this research provides policy maker and scientist with probabilities of indicative foliar injury for common urban Acer sp. trees that can help guide decisions about emissions controls. Further research should focus on mechanisms driving indicative fluoride injury over wide ranging foliar fluoride concentrations and help determine foliar fluoride thresholds for damage.

Combinatorial Effects of Arginine and Fluoride on Oral Bacteria

OpenAIRE

Zheng, X.; Cheng, X.; Wang, L.; Qiu, W.; Wang, S.; Zhou, Y.; Li, M.; Li, Y.; Cheng, L.; Li, J.; Zhou, X.; Xu, X.

2015-01-01

Dental caries is closely associated with the microbial disequilibrium between acidogenic/aciduric pathogens and alkali-generating commensal residents within the dental plaque. Fluoride is a widely used anticaries agent, which promotes tooth hard-tissue remineralization and suppresses bacterial activities. Recent clinical trials have shown that oral hygiene products containing both fluoride and arginine possess a greater anticaries effect compared with those containing fluoride alone, indicati...

Transportability Class of Americium in K Basin Sludge under Ambient and Hydrothermal Processing Conditions

Energy Technology Data Exchange (ETDEWEB)

Delegard, Calvin H.; Schmitt, Bruce E.; Schmidt, Andrew J.

2006-08-01

This report establishes the technical bases for using a ''slow uptake'' instead of a ''moderate uptake'' transportability class for americium-241 (241Am) for the K Basin Sludge Treatment Project (STP) dose consequence analysis. Slow uptake classes are used for most uranium and plutonium oxides. A moderate uptake class has been used in prior STP analyses for 241Am based on the properties of separated 241Am and its associated oxide. However, when 241Am exists as an ingrown progeny (and as a small mass fraction) within plutonium mixtures, it is appropriate to assign transportability factors of the predominant plutonium mixtures (typically slow) to the Am241. It is argued that the transportability factor for 241Am in sludge likewise should be slow because it exists as a small mass fraction as the ingrown progeny within the uranium oxide in sludge. In this report, the transportability class assignment for 241Am is underpinned with radiochemical characterization data on K Basin sludge and with studies conducted with other irradiated fuel exposed to elevated temperatures and conditions similar to the STP. Key findings and conclusions from evaluation of the characterization data and published literature are summarized here. Plutonium and 241Am make up very small fractions of the uranium within the K Basin sludge matrix. Plutonium is present at about 1 atom per 500 atoms of uranium and 241Am at about 1 atom per 19000 of uranium. Plutonium and americium are found to remain with uranium in the solid phase in all of the {approx}60 samples taken and analyzed from various sources of K Basin sludge. The uranium-specific concentrations of plutonium and americium also remain approximately constant over a uranium concentration range (in the dry sludge solids) from 0.2 to 94 wt%, a factor of {approx}460. This invariability demonstrates that 241Am does not partition from the uranium or plutonium fraction for any characterized sludge matrix. Most

Profile of Fluoride Release from a Nanohybrid Composite Resin

Directory of Open Access Journals (Sweden)

Raquel Assed Bezerra Silva

2015-02-01

Full Text Available The aim of this study was to evaluate in vitro the amount and profile of fluoride release from a fluoride-containing nanohybrid composite resin (Tetric® N-Ceram by direct potentiometry. Thirty specimens (5 mm diameter x 3 mm high; n=10/material were made of Tetric® N-Ceram, Vitremer® resin-modified glass ionomer cement (RMGIC (positive control or Filtek® Z350 nanofill composite resin (negative control. The specimens were stored individually in plastic tubes containing 1 mL of artificial saliva at 37°C, which was daily renewed during 15 days. At each renewal of saliva, the amount of fluoride ions released in the solution was measured using a fluoride ion-selective electrode with ion analyzer, and the values obtained in mV were converted to ppm (µg/mL. Data were analyzed statistically by ANOVA and Tukey’s post-hoc test at a significance level of 5%. The results showed that the resins Tetric® N-Ceram and Filtek® Z350 did not release significant amounts of fluoride during the whole period of evaluation (p>0.05. Only Vitremer® released significant amounts of fluoride ions during the 15 days of the experiment, with greater release in first 2 days (p0.05. In conclusion, the nanohybrid composite resin Tetric® N-Ceram did not present in vitro fluoride-releasing capacity throughout the 15 days of study.

Fluoride influences nickel-titanium orthodontic wires′ surface texture and friction resistance

Directory of Open Access Journals (Sweden)

Mona Aly Abbassy

2016-01-01

Full Text Available Objectives: The aim of this study was to investigate the effects exerted by the acidulated fluoride gel on stainless steel and nickel-titanium (Ni-Ti orthodontic wires. Materials and Methods: Sixty stainless steel and Ni-Ti orthodontic archwires were distributed into forty archwires used for in vitro study and twenty for in situ study. Fluoride was applied for 1 h in the in vitro experiment while it was applied for 5 min in the in situ experiment. The friction resistance of all wires with ceramic brackets before/after topical fluoride application was measured using a universal testing machine at 1 min intervals of moving wire. Moreover, surface properties of the tested wires before/after fluoride application and before/after friction test were examined by a scanning electron microscope (SEM. Dunnett′s t-test was used to compare frictional resistance of as-received stainless steel wires and Ni-Ti wires to the wires treated by fluoride in vitro and in situ (P < 0.05. Two-way ANOVA was used to compare the effect of fluoride application and type of wire on friction resistance in vitro and in situ (P < 0.05. Results: Ni-Ti wires recorded significantly high friction resistance after fluoride application when compared to stainless steel wires in vitro, P < 0.05. Fluoride application did not significantly affect the friction resistance of the tested wires in situ, P < 0.05. SEM observation revealed deterioration of the surface texture of the Ni-Ti wires after fluoride application in vitro and in situ. Conclusions: The in vitro fluoride application caused an increase in friction resistance of Ni-Ti wires when compared to stainless steel wires. In vitro and in situ fluoride application caused deterioration in surface properties of Ni-Ti wires.

Effect of fluoride mouthwash on tensile strength of stainless steel orthodontic archwires

Science.gov (United States)

Fatimah, D. I.; Anggani, H. S.; Ismah, N.

2017-08-01

Patients with orthodontic treatment are commonly recommended to use a fluoride mouthwash for maintaining their oral hygiene and preventing dental caries. However, fluoride may affect the characteristics of stainless steel orthodontic archwires used during treatment. The effect of fluoride mouthwash on the tensile strength of stainless steel orthodontic archwires is still unknown. The purpose of this study is to know the effect of fluoride mouthwash on the tensile strength of stainless steel orthodontic archwires. Examine the tensile strength of 0.016 inch stainless steel orthodontic archwires after immersion in 0.05%, 100 ml fluoride mouthwash for 30, 60, and 90 min. There is no statistically significant difference in the tensile strength of stainless steel orthodontic archwires after immersed in fluoride mouthwash. The p-values on immersion fluoride mouthwash for 30, 60, and 90 min consecutively are 0.790; 0.742; and 0.085 (p > 0.05). The use of fluoride mouthwash did not have an effect on the tensile strength of stainless Steel orthodontic archwires.

Fluoride Consumption and Its Impact on Oral Health

Directory of Open Access Journals (Sweden)

Luis Fernando Jacinto-Alemán

2011-01-01

Full Text Available Objective. The purpose of this study was to evaluate caries and dental fluorosis among Mexican preschoolers and school-aged children in a non-endemic zone for fluorosis and to measure its biological indicators. Methods. DMFT, DMFS, dmft, dmfs, and CDI indexes were applied. Fluoride urinary excretion and fluoride concentrations in home water, table salt, bottled water, bottled drinks, and toothpaste were determined. Results. Schoolchildren presented fluorosis (CDI = 0.96 and dental caries (DMFT = 2.64 and DMFS = 3.97. Preschoolers presented dmft = 4.85 and dmfs = 8.80. DMFT and DMFS were lower in children with mild to moderate dental fluorosis (DF. Variable fluoride concentrations were found in the analyzed products (home water = 0.18–0.44 ppm F, table salt = 0–485 ppm F, bottled water = 0.18–0.47 ppm F, juices = 0.08–1.42 ppm F, nectars = 0.07–1.30 ppm F, bottled drinks = 0.10–1.70 ppm F, toothpaste = 0–2,053 ppm F. Mean daily fluoride excretion was 422 ± 176 µg/24 h for schoolchildren and 367 ± 150 µg/24 h for preschoolers. Conclusions. Data from our study show that, despite values of excretion within an optimal fluoride intake range, the prevalence of caries was significant in both groups, and 60% of the 11- to 12-year-old children presented with dental fluorosis. In addition, variable fluoride concentrations in products frequently consumed by children were found.

Fluoride removal from aqueous solution by pumice: case study on ...

African Journals Online (AJOL)

The fluoride removal from synthetic water by pumice was studied at batch experiments in this study. The effect of pH, contact time, fluoride concentration and adsorbent dose on the fluoride sequestration was investigated. The optimum conditions were studied on Kuhbonan water as a case study. The results showed that ...

The Impact of Selected Fluoridated Toothpastes on Dental Erosion in Profilometric Measurement.

Science.gov (United States)

Fita, Katarzyna; Kaczmarek, Urszula

2016-01-01

Some fluoridated toothpastes, available commercially, are described to have a protective effect against dental erosion. To evaluate the influence of the selected marketed toothpastes on the human enamel exposed to acid beverages. Enamel specimens from extracted human teeth were prepared (n = 40). Specimens were randomly divided into 10 experimental groups, 4 specimens each, which were subjected to acid challenge for 10 min using orange juice (pH 3.79) or Pepsi Cola (pH 2.58) and then immersed for 2 min into a slurry of five marketed toothpastes with distilled water (1 : 3 w/w). The tested toothpastes contained 1450 or 5000 ppm fluoride, CPP-ACP with 900 ppm fluoride, 1450 ppm fluoride with potassium nitrate 5%, all of them as sodium fluoride, and 700 ppm fluoride as amine and sodium fluoride with 3500 ppm SnCl2. Enamel roughness (Ra parameter) by contact profilometer at baseline and after exposure onto soft drinks and slurry was measured. Exposure to both beverages caused a similar increase of enamel surface roughness. After the specimens immersion into slurries of toothpastes with 1450 or 5000 ppm fluoride, 1450 ppm fluoride with potassium nitrate 5% and CPP-ACP with 900 ppm fluoride the significant decrease of Ra values were found, reaching the baseline values. However, toothpaste with 700 ppm fluoride and 3500 ppm SnCl2 did not cause any fall in Ra value, probably due to other mechanism of action. Within the limitation of the study we can conclude that the sodium fluoride toothpastes are able to restore the surface profile of enamel exposed shortly to acidic soft drinks.

Fluoride in dental biofilm and saliva

DEFF Research Database (Denmark)

Larsen, Line Staun

Dette ph.d.-projekt bidrager med ny viden om fordelingen af fluorid i dental biofilm og saliva. For at udforske koncentrationen af fluorid i naturlig (in vivo) biofilmvæske, biofilmsediment og i saliva, blev der udført to meget forskellige kliniske studier. Resultaterne fra tværsnitsstudiet (Studie...... I), hos en stor gruppe mennesker (n=42) der konsulterede en tandklinik for behandling, bekræfter tidligere viden, at der findes en naturlig biologisk variation i fluoridkoncentrationerne i biofilm fra forskellige intra-orale regioner samt mellem biofilmvæske, biofilmsediment og saliva...... fluoridkoncentrationer i underkæbefronten, intermediære koncentrationer i alle tre overkæberegioner og de laveste koncentrationer i underkæbemolarregionerne. Begge studier viser at biofilmsedimentet indeholder størstedelen af fluorid i biofilm. Set i et bredere perspektiv viser fundene at der er et omvendt forhold...

Level of Fluoride in Soil, Grain and Water in Jalgaon District, Maharashtra, India.

Science.gov (United States)

Naik, Rahul Gaybarao; Dodamani, Arun Suresh; Vishwakarma, Prashanth; Jadhav, Harish Chaitram; Khairnar, Mahesh Ravindra; Deshmukh, Manjiri Abhay; Wadgave, Umesh

2017-02-01

Fluoride has an influence on both oral as well as systemic health. The major source of fluoride to body is through drinking water as well as through diet. Staple diet mainly depends on local environmental factors, food grains grown locally, its availability etc. Determination of fluoride level in these food grains is important. So, estimation of the amount of fluoride in grains and its relation to the sources of fluoride used for their cultivation viz., soil and water is important. To estimate the relation of fluoride concentration in grains (Jowar) with respect to that of soil and water used for their cultivation. Fifteen samples each of soil, water and grains were collected using standardized method from the same farm fields of randomly selected villages of Jalgaon district. Fluoride ion concentration was determined in laboratory using SPADNS technique. Mean difference in fluoride levels in between the groups were analyzed using ANOVA and Post-Hoc Tukey test. Linear regression method was applied to analyse the association of the fluoride content of grain with water and soil. There was a significant difference in between mean fluoride levels of soil and water (pwater and grain was found to be non significant (p=0.591). Also fluoride levels in all the three groups showed significant association with each other. Fluoride level of soil, grains and water should be adjusted to an optimum level. Soil has positive correlation with respect to uptake of fluoride by Jowar grains. So, Jowar grains with optimum fluoride content should be made available in the commercial markets so that oral and general health can be benefitted.

Effect of atmospheric fluoride on plant metabolism

Energy Technology Data Exchange (ETDEWEB)

Suketa, Y; Yamamoto, T

1971-05-01

Studies on the relationship between the exposure factor and foliar deposition of fluoride, or foliar burn, are introduced. Photosynthesis is adversely affected by atmospheric fluoride. The photosynthesis of a strawberry deteriorated by 50% when the strawberry was exposed to 48 ppb hydrofluoric acid for one hour. The effect of fluoride on the respiratory organs of plants is also reported. Soy beans exposed to 0.03 ppm HF had metabolic abnormalities. The total sugar quantity of leaves decreased from 242-253 mg/100 g to 111-141 mg/100 g and the non-reduced sugar/reduced sugar ratio decreased from 4.6-8.7 to 0.8-1.6. 30 references, 3 figures, 14 tables.

Modelling of fluoride removal via batch monopolar electrocoagulation process using aluminium electrodes

Science.gov (United States)

Amri, N.; Hashim, M. I.; Ismail, N.; Rohman, F. S.; Bashah, N. A. A.

2017-09-01

Electrocoagulation (EC) is a promising technology that extensively used to remove fluoride ions efficiently from industrial wastewater. However, it has received very little consideration and understanding on mechanism and factors that affecting the fluoride removal process. In order to determine the efficiency of fluoride removal in EC process, the effect of operating parameters such as voltage and electrolysis time were investigated in this study. A batch experiment with monopolar aluminium electrodes was conducted to identify the model of fluoride removal using empirical model equation. The EC process was investigated using several parameters which include voltage (3 - 12 V) and electrolysis time (0 - 60 minutes) at a constant initial fluoride concentration of 25 mg/L. The result shows that the fluoride removal efficiency increased steadily with increasing voltage and electrolysis time. The best fluoride removal efficiency was obtained with 94.8 % removal at 25 mg/L initial fluoride concentration, voltage of 12 V and 60 minutes electrolysis time. The results indicated that the rate constant, k and number of order, n decreased as the voltage increased. The rate of fluoride removal model was developed based on the empirical model equation using the correlation of k and n. Overall, the result showed that EC process can be considered as a potential alternative technology for fluoride removal in wastewater.

Prevention of dental caries through the effective use of fluoride

DEFF Research Database (Denmark)

Petersen, Poul Erik

2016-01-01

Background: The World Health Organization (WHO) emphasizes that dental caries is a severe public health problem across the world. The current global and regional patterns of dental caries reflect distinct risk profiles of countries which relate to the structure of the society, living conditions......, lifestyles, and the existence of preventive oral health programmes. Research conducted in high income countries documents that systematic use of fluoride reduces the burden of dental caries; such research is scarce in low and middle income countries. Objectives: This article reviews the evidence on effective...... use of fluoride, highlights the public health approach to fluoridation, and clarifies how automatic fluoridation contributes to breaking social inequities in dental caries. Data collection: Scientific publications on fluoride administration stored in PubMed/Medline and caries data from the WHO...

Effect of various rinsing protocols after use of amine fluoride/stannous fluoride toothpaste on the bacterial composition of dental plaque

NARCIS (Netherlands)

van Loveren, C.; Gerardu, V.A.M.; Sissons, C.H.; van Bekkum, M.; ten Cate, J.M.

2009-01-01

This clinical study evaluated the effect of different oral hygiene protocols on the bacterial composition of dental plaque. After a 2-week period of using fluoride-free toothpaste, 30 participants followed three 1-week experimental protocols, each followed by 2-week fluoride-free washout periods in

Effect of Enamel Caries Lesion Baseline Severity on Fluoride Dose-Response

Directory of Open Access Journals (Sweden)

Frank Lippert

2017-01-01

Full Text Available This study aimed to investigate the effect of enamel caries lesion baseline severity on fluoride dose-response under pH cycling conditions. Early caries lesions were created in human enamel specimens at four different severities (8, 16, 24, and 36 h. Lesions were allocated to treatment groups (0, 83, and 367 ppm fluoride as sodium fluoride based on Vickers surface microhardness (VHN and pH cycled for 5 d. The cycling model comprised 3 × 1 min fluoride treatments sandwiched between 2 × 60 min demineralization challenges with specimens stored in artificial saliva in between. VHN was measured again and changes versus lesion baseline were calculated (ΔVHN. Data were analyzed using two-way ANOVA (p<0.05. Increased demineralization times led to increased surface softening. The lesion severity×fluoride concentration interaction was significant (p<0.001. Fluoride dose-response was observed in all groups. Lesions initially demineralized for 16 and 8 h showed similar overall rehardening (ΔVHN and more than 24 and 36 h lesions, which were similar. The 8 h lesions showed the greatest fluoride response differential (367 versus 0 ppm F which diminished with increasing lesion baseline severity. The extent of rehardening as a result of the 0 ppm F treatment increased with increasing lesion baseline severity, whereas it decreased for the fluoride treatments. In conclusion, lesion baseline severity impacts the extent of the fluoride dose-response.

FLUORIDE LEVELS IN COMMERCIALLY AVAILABLE RICE IN ...

African Journals Online (AJOL)

Preferred Customer

2013-05-05

May 5, 2013 ... Rice is one of the commonly consumed cereals for more than half of the ... also used as flour, for making rice wine, as ingredient for beer and liquor, ... Fluoride is a necessary element to human health, and a moderate amount of fluoride intake ... For Ethiopian red rice (ERR) Fogera was selected to collect.

Removal of Fluoride from Drinking Water Using Modified Immobilized Activated Alumina

Directory of Open Access Journals (Sweden)

Aneeza Rafique

2013-01-01

Full Text Available The study describes the removal of fluoride from drinking water using modified immobilized activated alumina (MIAA prepared by sol-gel method. The modification was done by adding a specific amount of alum during the sol formation step. The fluoride removal efficiency of MIAA was 1.35 times higher as compared to normal immobilized activated alumina. A batch adsorption study was performed as a function of adsorbent dose, contact time, stirring rate, and initial fluoride concentration. More than 90% removal of fluoride was achieved within 60 minutes of contact time. The adsorption potential of MIAA was compared with activated charcoal which showed that the removal efficiency was about 10% more than the activated charcoal. Both the Langmuir and Freundlich adsorption isotherms fitted well for the fluoride adsorption on MIAA with the regression coefficient R2 of 0.99 and 0.98, respectively. MIAA can both be regenerated thermally and chemically. Adsorption experiments using MIAA were employed on real drinking water samples from a fluoride affected area. The study showed that modified immobilized activated alumina is an effective adsorbent for fluoride removal.

EURADOS intercomparison on measurements and Monte Carlo modelling for the assessment of Americium in a USTUR leg phantom

International Nuclear Information System (INIS)

Lopez, M. A.; Broggio, D.; Capello, K.; Cardenas-Mendez, E.; El-Faramawy, N.; Franck, D.; James, A. C.; Kramer, G. H.; Lacerenza, G.; Lynch, T. P.; Navarro, J. F.; Navarro, T.; Perez, B.; Ruehm, W.; Tolmachev, S. Y.; Weitzenegger, E.

2011-01-01

A collaboration of the EURADOS working group on 'Internal Dosimetry' and the United States Transuranium and Uranium Registries (USTUR) has taken place to carry out an intercomparison on measurements and Monte Carlo modelling determining americium deposited in the bone of a USTUR leg phantom. Preliminary results and conclusions of this intercomparison exercise are presented here. (authors)

Risk assessment of fluoride exposure in drinking water of Tunisia.

Science.gov (United States)

Guissouma, Wiem; Hakami, Othman; Al-Rajab, Abdul Jabbar; Tarhouni, Jamila

2017-06-01

The presence of fluoride in drinking water is known to reduce dental cavities among consumers, but an excessive intake of this anion might leads to dental and skeletal fluorosis. This study reports a complete survey of the fluoridated tap water taken from 100 water consumption points in Tunisia. The fluoride concentrations in tap water were between 0 and 2.4 mg L -1 . Risk assessment of Fluoride exposure was assessed depending on the age of consumers using a four-step method: hazard identification, toxicity reference values selection (TRVs), daily exposure assessment, and risk characterization. Our findings suggest that approximately 75% of the Tunisian population is at risk for dental decay, 25% have a potential dental fluorosis risk, and 20% might have a skeletal fluorosis risk according to the limits of fluoride in drinking water recommended by WHO. More investigations are recommended to assess the exposure risk of fluoride in other sources of drinking water such as bottled water. Copyright © 2017 Elsevier Ltd. All rights reserved.

On the assessment of hydroxyapatite fluoridation by means of Raman scattering

International Nuclear Information System (INIS)

Campillo, M.; Valiente, M.; Lacharmoise, P. D.; Reparaz, J. S.; Goni, A. R.

2010-01-01

Hydroxyapatite is the main mineral component of bones and teeth. Fluorapatite, a bioceramic that can be obtained from hydroxyapatite by chemical substitution of the hydroxide ions with fluoride, exhibits lower mineral solubility and larger mechanical strength. Despite the widespread use of fluoride against caries, a reliable technique for unambiguous assessment of fluoridation in in vitro tests is still lacking. Here we present a method to probe fluorapatite formation in fluoridated hydroxyapatite by combining Raman scattering with thermal annealing. In synthetic minerals, we found that effectively fluoride substituted hydroxyapatite transforms into fluorapatite only after heat treatment, due to the high activation energy for this first order phase transition.

On the assessment of hydroxyapatite fluoridation by means of Raman scattering

Science.gov (United States)

Campillo, M.; Lacharmoise, P. D.; Reparaz, J. S.; Goñi, A. R.; Valiente, M.

2010-06-01

Hydroxyapatite is the main mineral component of bones and teeth. Fluorapatite, a bioceramic that can be obtained from hydroxyapatite by chemical substitution of the hydroxide ions with fluoride, exhibits lower mineral solubility and larger mechanical strength. Despite the widespread use of fluoride against caries, a reliable technique for unambiguous assessment of fluoridation in in vitro tests is still lacking. Here we present a method to probe fluorapatite formation in fluoridated hydroxyapatite by combining Raman scattering with thermal annealing. In synthetic minerals, we found that effectively fluoride substituted hydroxyapatite transforms into fluorapatite only after heat treatment, due to the high activation energy for this first order phase transition.

Biosorption of fluoride ion from water using the seeds of the ...

African Journals Online (AJOL)

Biosorption of fluoride ion from water using the seeds of the cabbage tree ( Moringa ... The maximum fluoride sorption capacity was found to be 1.32 mg.g-1 of dry weight ... Key words: Biosorption, chemisorption, desorption, fluoride, isotherm, ...

Health impact of supplying safe drinking water containing fluoride below permissible level on flourosis patients in a fluoride-endemic rural area of West Bengal.

Science.gov (United States)

Majumdar, Kunal Kanti

2011-01-01

The problem of high fluoride concentration in groundwater resources has become one of the most important toxicological and geo-environmental issues in India. Excessive fluoride in drinking water causes dental and skeletal fluorosis, which is encountered in endemic proportions in several parts of the world. World Health Organization (WHO) guideline value and the permissible limit of fluoride as per Bureau of Indian Standard (BIS) is 1.5 mg/L. About 20 states of India, including 43 blocks of seven districts of West Bengal, were identified as endemic for fluorosis and about 66 million people in these regions are at risk of fluoride contamination. Studies showed that withdrawal of sources identified for fluoride often leads reduction of fluoride in the body fluids (re-testing urine and serum after a week or 10 days) and results in the disappearance of non-skeletal fluorosis within a short duration of 10-15 days. To determine the prevalence of signs and symptoms of suspected dental, skeletal, and non-skeletal fluorosis, along with food habits, addictions, and use of fluoride containing toothpaste among participants taking water with fluoride concentration above the permissible limit, and to assess the changes in clinical manifestations of the above participants after they started consuming safe drinking water. A longitudinal intervention study was conducted in three villages in Rampurhat Block I of Birbhum district of West Bengal to assess the occurrence of various dental, skeletal, and non-skeletal manifestations of fluorosis, along with food habits, addictions, and use of fluoride containing toothpaste among the study population and the impact of taking safe water from the supplied domestic and community filters on these clinical manifestations. The impact was studied by follow-up examination of the participants for 5 months to determine the changes in clinical manifestations of the above participants after they started consuming safe drinking water from supplied

Advanced inorganic fluorides. Proceedings of the Second International Siberian workshop INTERSIBFLUORINE-2006

International Nuclear Information System (INIS)

Volkov, V.V.; Mit'kin, V.N.; Bujnovskij, A.S.; Sofronov, V.L.

2006-01-01

Proceedings of the Second International Siberian workshop ISIF-2006 on modern inorganic fluorides contain full author's texts of 82 plenary reports and posters on the main trends in chemistry and technology of inorganic fluorides and their various applications. The following new trends are reflected in the ISIF-2006 Proceedings versus the ISIF-2003 ones: production and use of of nano-sized systems and materials based on fluoride phases and fluorinating systems; chemistry of fluorofullerenes, fluorides of graphite and carbon materials; development of research and technical principles of economically viable process of depleted uranium hexafluoride conversion; vitrifying systems based on metal fluorides possessing valuable functional optical properties; mechanochemical processes and phenomena in chemistry of inorganic fluorides [ru

Standardization of a method to study the distribution of Americium in purex process

International Nuclear Information System (INIS)

Dapolikar, T.T.; Pant, D.K.; Kapur, H.N.; Kumar, Rajendra; Dubey, K.

2017-01-01

In the present work the distribution of Americium in PUREX process is investigated in various process streams. For this purpose a method has been standardized for the determination of Am in process samples. The method involves extraction of Am with associated actinides using 30% TRPO-NPH at 0.3M HNO 3 followed by selective stripping of Am from the organic phase into aqueous phase at 6M HNO 3 . The assay of aqueous phase for Am content is carried out by alpha radiometry. The investigation has revealed that 100% Am follows the HLLW route. (author)

Application of extraction chromatography to the recovery of neptunium, plutonium and americium from an industrial waste

International Nuclear Information System (INIS)

Madic, C.; Kertesz, C.; Sontag, R.; Koehly, G.

1980-01-01

A pilot scale investigation was made to evaluate the possible application of the extraction chromatographic method (LLC) to the partitioning of alpha emitters from liquid wastes containing traces of transuranium elements. A secondary purpose was to obtain pure Am0 2 , which is used to produce alpha, gamma, and neutron sources. The process developed for alpha partitioning consists essentially of the extraction of macro amounts of uranium with 30% TBP in dodecane in mixer-settlers, then coextraction of Np-237, Pu-239, and Am-241 by LLC on a macro column filled with di-n-hexyl-octoxy-methyl-phosphine oxide (POX.11) adsorbed on an inert support. In each run about 200 liters of initial waste are decontaminated of alpha emitters. The loading step is followed by selective elution of americium, neptunium, and plutonium. The americium eluate is then subjected to the following operations: (1) separation of Am from Fe and Cd by LLC on a TBP column and (2) separation of Am from lanthanide traces by LLC on an HD(DiBM)P column after oxidation of Am(III) to Am(VI). The Am in the eluate is subsequently reduced to Am(III) and precipitated as oxalate with oxalic acid. The oxalate is then filtered and calcined to yield pure AmO 2

Effect of fluoride in drinking water on children′s intelligence in high and low fluoride areas of Delhi

Directory of Open Access Journals (Sweden)

Hansa Kundu

2015-01-01

Full Text Available Introduction: Fluoride is one of the indispensable elements for the living being. However, the intake of F above the threshold level can affect the central nervous system even before causing dental or skeletal fluorosis. Aim: The aim was to assess the effect of fluoride in drinking water on the intelligence quotient (IQ of 8-12 years old school going children residing in high and low Fluoride (F areas of Delhi. Materials and Methods: A total of 200 school children were selected, 100 from low F area and 100 from high F area. The IQ of the children was assessed using Ravens Standardized Progressive Matrices Test. Information for each child′s sociodemographic data, mother′s diet during pregnancy, duration of residency in the village, source of drinking water, and duration of drinking water from the source was entered on a specially designed proforma from mothers of children. Height and weight were also recorded for each child to assess the nutritional status. Independent t-test and Chi-square test was used to compare mean IQ scores in high and low fluoridated areas. Pearson′s correlation and multivariate linear regression were used to appraise the issue of all the study variables on IQ. Results: Comparison of mean IQ of children in both high (76.20 ± 19.10 and low F (85.80 ± 18.85 areas showed a significant difference (P = 0.013. Multiple regression analysis between child IQ and all other independent variables revealed that mother′s diet during pregnancy (P = 0.001 along with F in drinking water (P = 0.017 were the independent variables with the greatest explanatory power for child IQ variance (r2 = 0.417 without interaction with other variables. Conclusion: Fluoride in the drinking water was significantly related with the IQ of children. Along with fluoride, mother′s diet during pregnancy was also found to be significantly related with IQ of children. Researches in the same field are further advocated with large sample size and over a

Fluoride Removal From Drinking Water by Electrocoagulation Using Iron and Aluminum Electrodes

Directory of Open Access Journals (Sweden)

Takdastan

2014-07-01

Full Text Available Background Existence of fluoride in drinking water above the permissible level causes human skeletal fluorosis. Objectives Electrocoagulation by iron and aluminum electrodes was proposed for removing fluoride from drinking water. Materials and Methods Effects of different operating conditions such as treatment time, initial pH, applied voltage, type and number of electrodes, the spaces between aluminum and iron electrodes, and energy consumption during electrocoagulation were investigated in the batch reactor. Variable concentrations of fluoride solution were prepared by mixing proper amounts of sodium fluoride with deionized water. Results Experimental results showed that aluminum electrode is more effective in fluoride removal than iron, as in 40 minutes and initial pH of 7.5 at 20 V, the fluoride removal process reached to 97.86%. The final recommendable limit of fluoride (1.5 mg/L was obtained in 10 minutes at 20 V with the aluminum electrode. Conclusions In electrocoagulation with iron and aluminum electrodes, increase of voltage, number of electrodes and reaction time as well as decrease of the spaces between electrodes, enhanced the fluoride removal efficiency from drinking water. In addition the effect of pH and initial concentration of fluoride varied with types of electrodes.

Americium adsorption on the surface of macrophytic algae

Energy Technology Data Exchange (ETDEWEB)

Carvalho, F.P.; Fowler, S.W.

1985-01-01

Data are presented on the rates at which americium (Am) deposits upon blade surfaces of three benthic algal species (Ulva rigida, Fucus vesiculosus and Gigartina stellata) following short-term exposures (1-6 h). Am is taken up in direct proportion to the ambient radionuclide concentration in sea water. Uptake by the green alga was 3 to 5 times greater than that for the brown and red species. Experimental evidence indicated that Am accumulation is a passive process and that adsorption takes place mainly on the thin outer organic coating of the seaweed. The Am transport coefficients are quite similar to that previously found for the naturally occurring ..cap alpha..-emitter /sup 210/Po, but are an order of magnitude lower than a plutonium transport coefficient reported in the literature. Release of labelled extracellular products associated with the algal surface coating is considered to be responsible for the rapid loss of Am observed previously in macroalgae and may in fact serve as a mechanism for transferring Am to filter feeding zooplankton. (author).

Americium adsorption on the surface of macrophytic algae

International Nuclear Information System (INIS)

Carvalho, F.P.; Fowler, S.W.

1985-01-01

Data are presented on the rates at which americium (Am) deposits upon blade surfaces of three benthic algal species (Ulva rigida, Fucus vesiculosus and Gigartina stellata) following short-term exposures (1-6 h). Am is taken up in direct proportion to the ambient radionuclide concentration in sea water. Uptake by the green alga was 3 to 5 times greater than that for the brown and red species. Experimental evidence indicated that Am accumulation is a passive process and that adsorption takes place mainly on the thin outer organic coating of the seaweed. The Am transport coefficients are quite similar to that previously found for the naturally occurring α-emitter 210 Po, but are an order of magnitude lower than a plutonium transport coefficient reported in the literature. Release of labelled extracellular products associated with the algal surface coating is considered to be responsible for the rapid loss of Am observed previously in macroalgae and may in fact serve as a mechanism for transferring Am to filter feeding zooplankton. (author)

Inspection report of unauthorized possession and use of unsealed americium-241 and subsequent confiscation, J.C. Haynes Company, Newark, Ohio

International Nuclear Information System (INIS)

1985-11-01

This US Nuclear Regulatory Commission report documents the circumstances surrounding the March 26, 1985, confiscation and subsequent decontamination activities related to the use of unauthorized quantities of americium-241 at the John C. Haynes Company (licensee) of Newark, Ohio. It focuses on the period from early February to July 26, 1985. The incident started when NRC Region III recieved information that John C. Haynes possessed unauthorized quantities of americium-241 and was conducting unauthorized activities (diamond irradiation). By July 26, 1985, the decontamination activities at the licensee's laboratory were concluded. The licensee's actions with diamond irradiation resulted in contamination in restricted and unrestricted areas of the facility. The confiscation and decontamination activities required the combined efforts of NRC, Federal Bureau of Investigation, US Department of Energy, Oak Ridge Associated Universities, the State of Ohio, and the US Environmental Protection Agency. The report describes the factual information and significant findings associated with the confiscation and decontamination activities

FLUORIDE: A REVIEW OF USE AND EFFECTS ON HEALTH

OpenAIRE

Kanduti, Domen; Sterbenk, Petra; Artnik, Barbara

2016-01-01

Introduction: Appropriate oral health care is fundamental for any individual?s health. Dental caries is still one of the major public health problems. The most effective way of caries prevention is the use of fluoride. Aim: The aim of our research was to review the literature about fluoride toxicity and to inform physicians, dentists and public health specialists whether fluoride use is expedient and safe. Methods: Data we used in our review were systematically searched and collected from web...

Modification of radiation effect by sodium fluoride in Tradescantia

International Nuclear Information System (INIS)

Cebulska-Wasilewska, A.; Guminska, M.; Huczkowski, J.; Kuternozinska, W.

1988-01-01

Frequency of somatic mutations in the Tradescantia stamen hairs served as a measure of biological effect of gamma irradiation with single and split doses and of modifications caused by sodium fluoride. It was found that treatment of plants with fluoride before irradiation affects considerably radiation-induced mutations. The changed peak mutation frequency in plants treated with fluoride suggests that it vitally influences the repair processes of DNA and possibly modifies the mutation spectrum. 14 refs., 3 figs. (author)

Effect of high fluoride concentration in drinking water on children’s intelligence

Directory of Open Access Journals (Sweden)

Seraj B

2006-07-01

Full Text Available Background and Aim: Human and animal studies linking fluoride with diminished intelligence have been published. Although adverse effects of high intake of fluoride on intelligence and mental acuity continue to be reported, they are still controversial. The aim of this research was to investigate the relationship between fluoride in drinking water and children's intelligence. Materials and Methods: In this cross sectional study, 41 children were selected from the high fluoride area with 2.5mg/l (ppm fluoride in the drinking water and 85 children were selected from low fluoride area with 0.4mg/l (ppm fluoride in the drinking water. The intelligence quotient (IQ of each child was measured by the Raven's test. The history of illnesses affecting the nervous system, head trauma, birth weight (2.5kg or  2.5kg, residental history, age and sex of children were investigated by questionnaires completed by the children's parents. Data were analyzed by Chi-Square test with p<0.05 as the limit of significance. Results: In the high fluoride area the mean IQ of children (87.911 was significantly lower than in the low fluoride area (98.912.9 (P=0.025. Conclusion: Based on the findings of this study, exposure of children to high levels of fluoride may carry the risk of impaired development of intelligence.

The effect of water purification systems on fluoride content of drinking water

Directory of Open Access Journals (Sweden)

Prabhakar A

2008-03-01

Full Text Available Objective: The purpose of the present study was to determine the effect of different water purification systems on the fluoride content of drinking water and to compare the efficacy of these water purification systems in reducing the fluoride content. Materials and Methods: Five different water purification systems were tested in this study. They were reverse osmosis, distillation, activated carbon, Reviva ® , and candle filter. The water samples in the study were of two types, viz, borewell water and tap water, these being commonly used by the people of Davangere City, Karnataka. The samples were collected before and after purification, and fluoride analysis was done using fluoride ion-specific electrode. Results: The results showed that the systems based on reverse osmosis, viz, reverse osmosis system and Reviva ® showed maximum reduction in fluoride levels, the former proving to be more effective than the latter; followed by distillation and the activated carbon system, with the least reduction being brought about by candle filter. The amount of fluoride removed by the purification system varied between the system and from one source of water to the other. Interpretation and Conclusion: Considering the beneficial effects of fluoride on caries prevention; when drinking water is subjected to water purification systems that reduce fluoride significantly below the optimal level, fluoride supplementation may be necessary. The efficacy of systems based on reverse osmosis in reducing the fluoride content of water indicates their potential for use as defluoridation devices.

Nutritional and water effect on fluoride uptake and respiration of bean seedlings. [Phaseolus vulgaris

Energy Technology Data Exchange (ETDEWEB)

Applegate, H G; Adams, D F

1960-01-01

Bean plants (Phaseolus vulgaris) were grown in an atmosphere containing 2.0 +/- 0.21 g F /mT (1.6 ppb). The effect of N, P, K, Fe, and Ca deficiencies and the effect of osmotic pressures of 0, 1.5, 3.0, 4.5, 6.0 and 7.5 pounds on fluoride uptake and fluoride-mediated respiration were studied. The data showed that P deficient plants took up more fluoride than plants deficient in any of the other elements studied. Fluoride-mediated respiration was phosphorous dependent, however. Plants low in Fe or K showed increased uptake of fluoride. Nitrogen had no effect on fluoride uptake under the conditions of this experiment. Plants low in Fe showed inhibition of oxygen uptake. This inhibition was accentuated by fluoride. The interactions of N, K and Ca with fluoride on respiration were complex. Neither fluoride uptake nor fluoride-mediated respiration appeared to be linked directly to the water economy of the plants. 14 references, 6 tables.

The Effects of Remineralization via Fluoride Versus Low-Level Laser IR810 and Fluoride Agents on the Mineralization and Microhardness of Bovine Dental Enamel

Directory of Open Access Journals (Sweden)

Edith Lara-Carrillo

2018-01-01

Full Text Available The objective of this study was to assess the mineralization and microhardness of bovine dental enamel surfaces treated with fluoride, tri-calcium phosphate, and infrared (IR 810 laser irradiation. The study used 210 bovine incisors, which were divided into six groups (n = 35 in each: Group A: Untreated (control, Group B: Fluoride (Durapath-Colgate, Group C: Fluoride+Tri-calcium phosphate (Clin-Pro White-3 M, Group D: Laser IR 810 (Quantum, Group E: Fluoride+laser, and Group F: Fluoride+tri-calcium phosphate+laser. Mineralization was measured via UV-Vis spectroscopy for phosphorus and via atomic absorption spectroscopy for calcium upon demineralization and remineralization with proven agents. Microhardness (SMH was measured after enamel remineralization. Mineral loss data showed differences between the groups before and after the mineralizing agents were placed (p < 0.05. Fluoride presented the highest remineralization tendency for both calcium and phosphate, with a Vickers microhardness of 329.8 HV0.1/11 (p < 0.05. It was observed that, if remineralization solution contained fewer minerals, the microhardness surface values were higher (r = −0.268 and −0.208; p < 0.05. This study shows that fluoride has a remineralizing effect compared with calcium triphosphate and laser IR810. This in vitro study imitated the application of different remineralizing agents and showed which one was the most efficient for treating non-cavitated injuries. This can prevent the progression of lesions in patients with white spot lesions.

HOUSEHOLD PURIFICATION OF FLUORIDE CONTAMINATED MAGADI (TRONA)

DEFF Research Database (Denmark)