WorldWideScience

Sample records for aluminum oxide

  1. Burning characteristics of individual aluminum/aluminum oxide particles

    OpenAIRE

    Ruttenberg, Eric C.

    1996-01-01

    Approved for public release; distribution is unlimited An experimental investigation was conducted in which the burning characteristics of individual aluminum/aluminum oxide particles were measured using a windowed combustion bomb at atmospheric pressure and under gravity-fall conditions. A scanning electron microscope (SEM) was used to measure the size distribution of the initial aluminum particles and the aluminum oxide residue. Analysis of the residue indicated that the mass of aluminum...

  2. Oxidation kinetics of aluminum diboride

    Science.gov (United States)

    Whittaker, Michael L.; Sohn, H. Y.; Cutler, Raymond A.

    2013-11-01

    The oxidation characteristics of aluminum diboride (AlB2) and a physical mixture of its constituent elements (Al+2B) were studied in dry air and pure oxygen using thermal gravimetric analysis to obtain non-mechanistic kinetic parameters. Heating in air at a constant linear heating rate of 10 °C/min showed a marked difference between Al+2B and AlB2 in the onset of oxidation and final conversion fraction, with AlB2 beginning to oxidize at higher temperatures but reaching nearly complete conversion by 1500 °C. Kinetic parameters were obtained in both air and oxygen using a model-free isothermal method at temperatures between 500 and 1000 °C. Activation energies were found to decrease, in general, with increasing conversion for AlB2 and Al+2B in both air and oxygen. AlB2 exhibited O2-pressure-independent oxidation behavior at low conversions, while the activation energies of Al+2B were higher in O2 than in air. Differences in the composition and morphology between oxidized Al+2B and AlB2 suggested that Al2O3-B2O3 interactions slowed Al+2B oxidation by converting Al2O3 on aluminum particles into a Al4B2O9 shell, while the same Al4B2O9 developed a needle-like morphology in AlB2 that reduced oxygen diffusion distances and increased conversion. The model-free kinetic analysis was critical for interpreting the complex, multistep oxidation behavior for which a single mechanism could not be assigned. At low temperatures, moisture increased the oxidation rate of Al+2B and AlB2, but both appear to be resistant to oxidation in cool, dry environments.

  3. Oxidation dynamics of aluminum nanorods

    International Nuclear Information System (INIS)

    Aluminum nanorods (Al-NRs) are promising fuels for pyrotechnics due to the high contact areas with oxidizers, but their oxidation mechanisms are largely unknown. Here, reactive molecular dynamics simulations are performed to study thermally initiated burning of oxide-coated Al-NRs with different diameters (D = 26, 36, and 46 nm) in oxygen environment. We found that thinner Al-NRs burn faster due to the larger surface-to-volume ratio. The reaction initiates with the dissolution of the alumina shell into the molten Al core to generate heat. This is followed by the incorporation of environmental oxygen atoms into the resulting Al-rich shell, thereby accelerating the heat release. These results reveal an unexpectedly active role of the alumina shell as a “nanoreactor” for oxidation

  4. Oxidation kinetics of aluminum diboride

    International Nuclear Information System (INIS)

    The oxidation characteristics of aluminum diboride (AlB2) and a physical mixture of its constituent elements (Al+2B) were studied in dry air and pure oxygen using thermal gravimetric analysis to obtain non-mechanistic kinetic parameters. Heating in air at a constant linear heating rate of 10 °C/min showed a marked difference between Al+2B and AlB2 in the onset of oxidation and final conversion fraction, with AlB2 beginning to oxidize at higher temperatures but reaching nearly complete conversion by 1500 °C. Kinetic parameters were obtained in both air and oxygen using a model-free isothermal method at temperatures between 500 and 1000 °C. Activation energies were found to decrease, in general, with increasing conversion for AlB2 and Al+2B in both air and oxygen. AlB2 exhibited O2-pressure-independent oxidation behavior at low conversions, while the activation energies of Al+2B were higher in O2 than in air. Differences in the composition and morphology between oxidized Al+2B and AlB2 suggested that Al2O3–B2O3 interactions slowed Al+2B oxidation by converting Al2O3 on aluminum particles into a Al4B2O9 shell, while the same Al4B2O9 developed a needle-like morphology in AlB2 that reduced oxygen diffusion distances and increased conversion. The model-free kinetic analysis was critical for interpreting the complex, multistep oxidation behavior for which a single mechanism could not be assigned. At low temperatures, moisture increased the oxidation rate of Al+2B and AlB2, but both appear to be resistant to oxidation in cool, dry environments. - Graphical abstract: Isothermal kinetic data for AlB2 in air, showing a constantly decreasing activation energy with increasing conversion. Model-free analysis allowed for the calculation of global kinetic parameters despite many simultaneous mechanisms occurring concurrently. (a) Time–temperature plots, (b) conversion as a function of time, (c) Arrhenius plots used to calculate activation energies, and (d) activation energy

  5. Photoemission study of tris(8-hydroxyquinoline) aluminum/aluminum oxide/tris(8-hydroxyquinoline) aluminum interface

    International Nuclear Information System (INIS)

    The evolution of the interface electronic structure of a sandwich structure involving aluminum oxide and tris(8-hydroxyquinoline) aluminum (Alq), i.e. (Alq/AlOx/Alq), has been investigated with photoemission spectroscopy. Strong chemical reactions have been observed due to aluminum deposition onto the Alq substrate. The subsequent oxygen exposure releases some of the Alq molecules from the interaction with aluminum. Finally, the deposition of the top Alq layer leads to an asymmetry in the electronic energy level alignment with respect to the AlOx interlayer

  6. Formulation and method for preparing gels comprising hydrous aluminum oxide

    Science.gov (United States)

    Collins, Jack L.

    2014-06-17

    Formulations useful for preparing hydrous aluminum oxide gels contain a metal salt including aluminum, an organic base, and a complexing agent. Methods for preparing gels containing hydrous aluminum oxide include heating a formulation to a temperature sufficient to induce gel formation, where the formulation contains a metal salt including aluminum, an organic base, and a complexing agent.

  7. Specific features of aluminum nanoparticle water and wet air oxidation

    International Nuclear Information System (INIS)

    The oxidation processes of the electrically exploded aluminum nanopowders in water and in wet air are examined in the paper. The morphology of the intermediate reaction products of aluminum oxidation has been studied using the transmission electron microscopy. It was shown that the aluminum nanopowder water oxidation causes the formation of the hollow spheres with mesoporous boehmite nanosheets coating. The wedge-like bayerite particles are formed during aluminum nanopowder wet air oxidation

  8. 21 CFR 73.1015 - Chromium-cobalt-aluminum oxide.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Chromium-cobalt-aluminum oxide. 73.1015 Section 73... LISTING OF COLOR ADDITIVES EXEMPT FROM CERTIFICATION Drugs § 73.1015 Chromium-cobalt-aluminum oxide. (a) Identity. The color additive chromium-cobalt-aluminum oxide is a blue-green pigment obtained by calcining...

  9. Monolithic Approach to Oxide Dispersion Strengthened Aluminum Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Nassau Stern Company is investigating an approach for manufacturing oxide dispersion strengthened (ODS) aluminum in bulk rather than powder form. The approach...

  10. Air-Impregnated Nanoporous Anodic Aluminum Oxide Layers for Enhancing the Corrosion Resistance of Aluminum.

    Science.gov (United States)

    Jeong, Chanyoung; Lee, Junghoon; Sheppard, Keith; Choi, Chang-Hwan

    2015-10-13

    Nanoporous anodic aluminum oxide layers were fabricated on aluminum substrates with systematically varied pore diameters (20-80 nm) and oxide thicknesses (150-500 nm) by controlling the anodizing voltage and time and subsequent pore-widening process conditions. The porous nanostructures were then coated with a thin (only a couple of nanometers thick) Teflon film to make the surface hydrophobic and trap air in the pores. The corrosion resistance of the aluminum substrate was evaluated by a potentiodynamic polarization measurement in 3.5 wt % NaCl solution (saltwater). Results showed that the hydrophobic nanoporous anodic aluminum oxide layer significantly enhanced the corrosion resistance of the aluminum substrate compared to a hydrophilic oxide layer of the same nanostructures, to bare (nonanodized) aluminum with only a natural oxide layer on top, and to the latter coated with a thin Teflon film. The hydrophobic nanoporous anodic aluminum oxide layer with the largest pore diameter and the thickest oxide layer (i.e., the maximized air fraction) resulted in the best corrosion resistance with a corrosion inhibition efficiency of up to 99% for up to 7 days. The results demonstrate that the air impregnating the hydrophobic nanopores can effectively inhibit the penetration of corrosive media into the pores, leading to a significant improvement in corrosion resistance. PMID:26393523

  11. Fabrication of anodic aluminum oxide with incorporated chromate ions

    Science.gov (United States)

    Stępniowski, Wojciech J.; Norek, Małgorzata; Michalska-Domańska, Marta; Bombalska, Aneta; Nowak-Stępniowska, Agata; Kwaśny, Mirosław; Bojar, Zbigniew

    2012-10-01

    The anodization of aluminum in 0.3 M chromic acid is studied. The influence of operating conditions (like anodizing voltage and electrolyte's temperature) on the nanoporous anodic aluminum oxide geometry (including pore diameter, interpore distance, the oxide layer thickness and pores density) is thoroughly investigated. The results revealed typical correlations of the anodic alumina nanopore geometry with operating conditions, such as linear increase of pore diameter and interpore distance with anodizing voltage. The anodic aluminum oxide is characterized by a low pores arrangement, as determined by Fast Fourier transforms analyses of the FE-SEM images, which translates into a high concentration of oxygen vacancies. Moreover, an optimal experimental condition where chromate ions are being successfully incorporated into the anodic alumina walls, have been determined: the higher oxide growth rate the more chromate ions are being trapped. The trapped chromate ions and a high concentration of oxygen vacancies make the anodic aluminum oxide a promising luminescent material.

  12. Electrodeposition of Vanadium Oxide/Manganese Oxide Hybrid Thin Films on Nanostructured Aluminum Substrates

    OpenAIRE

    Rehnlund, David; Valvo, Mario; Edström, Kristina; Nyholm, Leif

    2014-01-01

    Electrodeposition of functional coatings on aluminum electrodes in aqueous solutions often is impeded by the corrosion of aluminum. In the present work it is demonstrated that electrodeposition of vanadium, oxide films on nanostructured aluminum substrates can be achieved in acidic electrolytes employing a novel strategy in which a thin interspacing layer of manganese oxide is first electrodeposited on aluminum microrod substrates. Such deposited films, which were studied using SEM, XPS, XRD,...

  13. Research on Interpore Distance of Anodic Aluminum Oxide Template

    OpenAIRE

    Liu, Xue-jie; Li, Liang-fang

    2013-01-01

    The relationship between the interpore of anodic aluminum oxide (AAO) template and the influencing factors of electrolyte, temperature and oxidation voltage etc. was researched and summarized in this paper. It was pointed out that the interpore was influenced mostly by electrolyte type and oxidation voltage, and least by the electrolyte concentration and oxidation temperature. The interpore of AAO template increases with the oxidation voltage increases. By adjusting the electrolyte and oxidat...

  14. Modeling the Shock Ignition of a Copper Oxide Aluminum Thermite

    Science.gov (United States)

    Lee, Kibaek; Stewart, D. Scott; Clemenson, Michael; Glumac, Nick; Murzyn, Christopher

    2015-06-01

    An experimental ``striker confinement'' shock compression test was developed in the Glumac-group at the University of Illinois to study ignition and reaction in composite reactive materials. These include thermitic and intermetallic reactive powders. The test places a sample of materials such as a thermite mixture of copper oxide and aluminum powders that are initially compressed to about 80 percent full density. Two RP-80 detonators simultaneously push steel bars into reactive material and the resulting compression causes shock compaction of the material and rapid heating. At that point one observes significant reaction and propagation of fronts. But the fronts are peculiar in that they are comprised of reactive events that can be traced to the reaction/diffusion of the initially separated reactants of copper oxide and aluminum that react at their mutual interfaces that nominally make copper liquid and aluminum oxide products. We discuss our model of the shock ignition of the copper oxide aluminum thermite in the context of the striker experiment and how a Gibbs formulation model, that includes multi-components for liquid and solid phases of aluminum, copper oxide, copper and aluminum oxide can predict the events observed at the particle scale in the experiments. Supported by HDTRA1-10-1-0020 (DTRA), N000014-12-1-0555 (ONR).

  15. Hangzhou Jinjiang Group Shanxi Fusheng Aluminum Phase I 800,000 t/a Aluminum Oxide Project Started Operation

    Institute of Scientific and Technical Information of China (English)

    2014-01-01

    <正>On October 19,the Shanxi Province Pinglu County Phase I 800,000t/a Aluminum Oxide Project of Shanxi Fusheng Aluminum Co.,Ltd,a subordinate of Hangzhou Jinjiang Group,started operation.This is the fourth Aluminum oxide project constructed and operated by Jinjiang Group.

  16. Preparation of Aluminum Nanomesh Thin Films from an Anodic Aluminum Oxide Template as Transparent Conductive Electrodes

    Science.gov (United States)

    Li, Yiwen; Chen, Yulong; Qiu, Mingxia; Yu, Hongyu; Zhang, Xinhai; Sun, Xiao Wei; Chen, Rui

    2016-02-01

    We have employed anodic aluminum oxide as a template to prepare ultrathin, transparent, and conducting Al films with a unique nanomesh structure for transparent conductive electrodes. The anodic aluminum oxide template is obtained through direct anodization of a sputtered Al layer on a glass substrate, and subsequent wet etching creates the nanomesh metallic film. The optical and conductive properties are greatly influenced by experimental conditions. By tuning the anodizing time, transparent electrodes with appropriate optical transmittance and sheet resistance have been obtained. The results demonstrate that our proposed strategy can serve as a potential method to fabricate low-cost TCEs to replace conventional indium tin oxide materials.

  17. Chemical Liquid Phase Deposition of Thin Aluminum Oxide Films

    OpenAIRE

    Sun, Jie; Sun, Yingchun

    2007-01-01

    Thin aluminum oxide films were deposited by a new and simple physicochemical method called chemical liquid phase deposition (CLD) on semiconductor materials. Aluminum sulfate with crystallized water and sodium bicarbonate were used as precursors for film growth, and the control of the system pH value played an important role in this experiment. The growth rate is 12 nm/h at room temperature. Post-growth annealing not only densifies and purifies the films, but results in film crystallization a...

  18. Effect of sealing on the morphology of anodized aluminum oxide

    International Nuclear Information System (INIS)

    Highlights: • We explored structural change of anodizing aluminum oxide induced by sealing. • All sealing methods decrease pore size as shown by X-ray/neutron scattering. • Cold sealing and hot water sealing do not alter the aluminum oxide framework. • Hot nickel acetate sealing both fills the pores and deposits on air oxide interface. • Samples with hot nickel acetate sealing outperform other sealing methods. - Abstract: Ultra-small angle X-ray scattering (USAXS), small-angle neutron scattering (SANS), X-ray reflectometry (XRR) and neutron reflectometry (NR) were used to probe structure evolution induced by sealing of anodized aluminum. While cold nickel acetate sealing and hot-water sealing decrease pore size, these methods do not alter the cylindrical porous framework of the anodic aluminum oxide layer. Hot nickel acetate both fills the pores and deposits on the air surface (air–oxide interface), leading to low porosity and small mean pore radius (39 Å). Electrochemical impedance spectroscopy and direct current polarization show that samples sealed by hot nickel acetate outperform samples sealed by other sealing methods

  19. Sorption of 90Sr by an aluminum oxide

    International Nuclear Information System (INIS)

    The sorption mechanism of an alkaline-earth bivalent cation on activated aluminum oxide is compared to the sorption mechanism of a monovalent ion. The selective retention of the alkaline-earth cation is made use of to remove trace amounts of Sr90 from radioactive waste waters. A kinetic study is reported, leading to the calculation of an industrial column. (author)

  20. OXYANION SORPTION TO HIGH SURFACE AREA IRON AND ALUMINUM OXIDES

    Science.gov (United States)

    Sorption of selected oxyanions (Mo, As, and P) to high surface area iron and aluminum oxides was investigated using in situ Raman and ATR-FTIR spectroscopy, batch sorption methods, electrophoretic mobility measurements, and surface complexation modeling. In situ ATR-FTIR and Raman spectra were coup...

  1. 21 CFR 73.3110a - Chromium-cobalt-aluminum oxide.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Chromium-cobalt-aluminum oxide. 73.3110a Section... LISTING OF COLOR ADDITIVES EXEMPT FROM CERTIFICATION Medical Devices § 73.3110a Chromium-cobalt-aluminum oxide. (a) Identity. The color additive chromium-cobalt-aluminum oxide (Pigment Blue 36) (CAS Reg....

  2. Reduction of Oxidative Melt Loss of Aluminum and Its Alloys

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Subodh K. Das; Shridas Ningileri

    2006-03-17

    This project led to an improved understanding of the mechanisms of dross formation. The microstructural evolution in industrial dross samples was determined. Results suggested that dross that forms in layers with structure and composition determined by the local magnesium concentration alone. This finding is supported by fundamental studies of molten metal surfaces. X-ray photoelectron spectroscopy data revealed that only magnesium segregates to the molten aluminum alloy surface and reacts to form a growing oxide layer. X-ray diffraction techniques that were using to investigate an oxidizing molten aluminum alloy surface confirmed for the first time that magnesium oxide is the initial crystalline phase that forms during metal oxidation. The analytical techniques developed in this project are now available to investigate other molten metal surfaces. Based on the improved understanding of dross initiation, formation and growth, technology was developed to minimize melt loss. The concept is based on covering the molten metal surface with a reusable physical barrier. Tests in a laboratory-scale reverberatory furnace confirmed the results of bench-scale tests. The main highlights of the work done include: A clear understanding of the kinetics of dross formation and the effect of different alloying elements on dross formation was obtained. It was determined that the dross evolves in similar ways regardless of the aluminum alloy being melted and the results showed that amorphous aluminum nitride forms first, followed by amorphous magnesium oxide and crystalline magnesium oxide in all alloys that contain magnesium. Evaluation of the molten aluminum alloy surface during melting and holding indicated that magnesium oxide is the first crystalline phase to form during oxidation of a clean aluminum alloy surface. Based on dross evaluation and melt tests it became clear that the major contributing factor to aluminum alloy dross was in the alloys with Mg content. Mg was

  3. Effect of processing on structural features of anodic aluminum oxides

    Science.gov (United States)

    Erdogan, Pembe; Birol, Yucel

    2012-09-01

    Morphological features of the anodic aluminum oxide (AAO) templates fabricated by electrochemical oxidation under different processing conditions were investigated. The selection of the polishing parameters does not appear to be critical as long as the aluminum substrate is polished adequately prior to the anodization process. AAO layers with a highly ordered pore distribution are obtained after anodizing in 0.6 M oxalic acid at 20 °C under 40 V for 5 minutes suggesting that the desired pore features are attained once an oxide layer develops on the surface. While the pore features are not affected much, the thickness of the AAO template increases with increasing anodization treatment time. Pore features are better and the AAO growth rate is higher at 20 °C than at 5 °C; higher under 45 V than under 40 V; higher with 0.6 M than with 0.3 M oxalic acid.

  4. Progress in Nano-Engineered Anodic Aluminum Oxide Membrane Development

    Directory of Open Access Journals (Sweden)

    Gerrard Eddy Jai Poinern

    2011-02-01

    Full Text Available The anodization of aluminum is an electro-chemical process that changes the surface chemistry of the metal, via oxidation, to produce an anodic oxide layer. During this process a self organized, highly ordered array of cylindrical shaped pores can be produced with controllable pore diameters, periodicity and density distribution. This enables anodic aluminum oxide (AAO membranes to be used as templates in a variety of nanotechnology applications without the need for expensive lithographical techniques. This review article is an overview of the current state of research on AAO membranes and the various applications of nanotechnology that use them in the manufacture of nano-materials and devices or incorporate them into specific applications such as biological/chemical sensors, nano-electronic devices, filter membranes and medical scaffolds for tissue engineering.

  5. H₂O Dissociation-Induced Aluminum Oxide Growth on Oxidized Al(111) Surfaces.

    Science.gov (United States)

    Liu, Qianqian; Tong, Xiao; Zhou, Guangwen

    2015-12-01

    The interaction of water vapor with amorphous aluminum oxide films on Al(111) is studied using X-ray photoelectron spectroscopy to elucidate the passivation mechanism of the oxidized Al(111) surfaces. Exposure of the aluminum oxide film to water vapor results in self-limiting Al2O3/Al(OH)3 bilayer film growth via counter-diffusion of both ions, Al outward and OH inward, where a thinner starting aluminum oxide film is more reactive toward H2O dissociation-induced oxide growth because of the thickness-dependent ionic transport in the aluminum oxide film. The aluminum oxide film exhibits reactivity toward H2O dissociation in both low-vapor pressure [p(H2O) = 1 × 10(-6) Torr] and intermediate-vapor pressure [p(H2O) = 5 Torr] regimes. Compared to the oxide film growth by exposure to a p(H2O) of 1 × 10(-6) Torr, the exposure to a p(H2O) of 5 Torr results in the formation of a more open structure of the inner Al(OH)3 layer and a more compact outer Al2O3 layer, demonstrating the vapor-pressure-dependent atomic structure in the passivating layer. PMID:26550986

  6. Thermocurrent dosimetry with high purity aluminum oxide

    Energy Technology Data Exchange (ETDEWEB)

    Fullerton, G.D.; Cameron, J.R.; Moran, P.R.

    1976-01-01

    The application of thermocurrent (TC) to ionizing radiation dosimetry was studied. It was shown that TC in alumina (Al/sub 2/O/sub 3/) has properties that are suited to personnel dosimetry and environmental monitoring. TC dosimeters were made from thin disks of alumina. Aluminum electrodes were evaporated on each side: on one face a high voltage electrode and on the opposite face a measuring electrode encircled by a guard ring. Exposure to ionizing radiation resulted in stored electrons and holes in metastable trapping sites. The signal was read-out by heating the dosimeter with a voltage source and picnometer connected in series between the opposite electrodes. The thermally remobilized charge caused a transient TC. The thermogram, TC versus time or temperature, is similar to a TL glow curve. Either the peak current or the integrated current is a measure of absorbed dose. Six grades of alumina were studied from a total of four commercial suppliers. All six materials displayed radiation induced TC signals. Sapphire of uv-grade quality from the Adolf Meller Co. (AM) had the best dosimetry properties of those investigated. Sources of interference were studied. Thermal fading, residual signal and radiation damage do not limit TC dosimetry. Ultraviolet light can induce a TC response but it is readily excluded with uv-opaque cladding. Improper surface preparation prior to electrode evaporation was shown to cause interference. A spurious TC signal resulted from polarization of surface contaminants. Spurious TC was reduced by improved cleaning prior to electrode application. Polished surfaces resulted in blocking electrodes and caused a sensitivity shift due to radiation induced thermally activated polarization. This was not observed with rough cut surfaces.

  7. Thermally stimulated luminescence studies in combustion synthesized polycrystalline aluminum oxide

    Indian Academy of Sciences (India)

    K R Nagabhushana; B N Lakshminarasappa; D Revannasiddaiah; Fouran Singh

    2008-08-01

    Synthesis of materials by combustion technique results in homogeneous and fine crystalline product. Further, the technique became more popular since it not only saved time and energy but also was easy to process. Aluminum oxide phosphor was synthesized by using urea as fuel in combustion reaction. Photoluminescence (PL) and thermally stimulated luminescence (TSL) characteristics of -irradiated aluminum oxide samples were studied. A broad PL emission with a peak at ∼ 465 nm and a pair of strong and sharp emissions with peaks at 679 and 695 nm were observed in -rayed samples. The PL intensity was observed to increase with increase in -ray dose. Two prominent and well resolved TSL glows with peaks at 210°C and 365°C were observed in all -irradiated Al2O3 samples. The TSL intensity was also found to increase with increase in -ray dose. The TSL glow curves indicated second order kinetics.

  8. Catalytic Behaviour of Mesoporous Cobalt-Aluminum Oxides for CO Oxidation

    Directory of Open Access Journals (Sweden)

    Ankur Bordoloi

    2014-01-01

    Full Text Available Ordered mesoporous materials are promising catalyst supports due to their uniform pore size distribution, high specific surface area and pore volume, tunable pore sizes, and long-range ordering of the pore packing. The evaporation-induced self-assembly (EISA process was applied to synthesize mesoporous mixed oxides, which consist of cobalt ions highly dispersed in an alumina matrix. The characterization of the mesoporous mixed cobalt-aluminum oxides with cobalt loadings in the range from 5 to 15 wt% and calcination temperatures of 673, 973, and 1073 K indicates that Co2+ is homogeneously distributed in the mesoporous alumina matrix. As a function of the Co loading, different phases are present comprising poorly crystalline alumina and mixed cobalt aluminum oxides of the spinel type. The mixed cobalt-aluminum oxides were applied as catalysts in CO oxidation and turned out to be highly active.

  9. Atomic layer deposited aluminum oxide barrier coatings for packaging materials

    Energy Technology Data Exchange (ETDEWEB)

    Hirvikorpi, Terhi, E-mail: terhi.hirvikorpi@vtt.f [Oy Keskuslaboratorio - Centrallaboratorium Ab (KCL), P.O. Box 70, FI-02151 Espoo (Finland); Vaehae-Nissi, Mika, E-mail: mika.vaha-nissi@vtt.f [Oy Keskuslaboratorio - Centrallaboratorium Ab (KCL), P.O. Box 70, FI-02151 Espoo (Finland); Mustonen, Tuomas, E-mail: tuomas.mustonen@vtt.f [Oy Keskuslaboratorio - Centrallaboratorium Ab (KCL), P.O. Box 70, FI-02151 Espoo (Finland); Iiskola, Eero, E-mail: eero.iiskola@kcl.f [Oy Keskuslaboratorio - Centrallaboratorium Ab (KCL), P.O. Box 70, FI-02151 Espoo (Finland); Karppinen, Maarit, E-mail: maarit.karppinen@tkk.f [Laboratory of Inorganic Chemistry, Department of Chemistry, Helsinki University of Technology, P.O. Box 6100, FI-02015 TKK (Finland)

    2010-03-01

    Thin aluminum oxide coatings have been deposited at a low temperature of 80 {sup o}C on various uncoated papers, polymer-coated papers and boards and plain polymer films using the atomic layer deposition (ALD) technique. The work demonstrates that such ALD-grown Al{sub 2}O{sub 3} coatings efficiently enhance the gas-diffusion barrier performance of the studied porous and non-porous materials towards oxygen, water vapor and aromas.

  10. Effect of aluminum metal surface on oxidation of iodide under gamma irradiation conditions

    International Nuclear Information System (INIS)

    The effects of aluminum surface on I- oxidation under gamma irradiation were investigated. Without irradiation, only O2 oxidized I- at pH < 2, and aluminum expedited the oxidation reaction. With irradiation, the radiolysis products from water and air oxidized I- into I3-. At pH < 2, O2 generated by water radiolysis additionally oxidized I-. However, at pH > 6, the H2O2 radiolysis product reduced I3- into I-. A smaller amount of I3- was observed in pH 1.9 and 3.3 solutions in contact with aluminum under irradiation because oxidants preferentially oxidize aluminum rather than I-. Moreover, for pH < 6.0, even less I3- was formed by aluminum exposed to air because air radiolysis products also preferentially oxidized aluminum. (author)

  11. A nine-atom rhodium–aluminum oxide cluster oxidizes five carbon monoxide molecules

    Science.gov (United States)

    Li, Xiao-Na; Zhang, Hua-Min; Yuan, Zhen; He, Sheng-Gui

    2016-01-01

    Noble metals can promote the direct participation of lattice oxygen of very stable oxide materials such as aluminum oxide, to oxidize reactant molecules, while the fundamental mechanism of noble metal catalysis is elusive. Here we report that a single atom of rhodium, a powerful noble metal catalyst, can promote the transfer of five oxygen atoms to oxidize carbon monoxide from a nine-atom rhodium–aluminum oxide cluster. This is a sharp improvement in the field of cluster science where the transfer of at most two oxygen atoms from a doped cluster is more commonly observed. Rhodium functions not only as the preferred trapping site to anchor and oxidize carbon monoxide by the oxygen atoms in direct connection with rhodium but also the primarily oxidative centre to accumulate the large amounts of electrons and the polarity of rhodium is ultimately transformed from positive to negative. PMID:27094921

  12. A nine-atom rhodium-aluminum oxide cluster oxidizes five carbon monoxide molecules.

    Science.gov (United States)

    Li, Xiao-Na; Zhang, Hua-Min; Yuan, Zhen; He, Sheng-Gui

    2016-01-01

    Noble metals can promote the direct participation of lattice oxygen of very stable oxide materials such as aluminum oxide, to oxidize reactant molecules, while the fundamental mechanism of noble metal catalysis is elusive. Here we report that a single atom of rhodium, a powerful noble metal catalyst, can promote the transfer of five oxygen atoms to oxidize carbon monoxide from a nine-atom rhodium-aluminum oxide cluster. This is a sharp improvement in the field of cluster science where the transfer of at most two oxygen atoms from a doped cluster is more commonly observed. Rhodium functions not only as the preferred trapping site to anchor and oxidize carbon monoxide by the oxygen atoms in direct connection with rhodium but also the primarily oxidative centre to accumulate the large amounts of electrons and the polarity of rhodium is ultimately transformed from positive to negative. PMID:27094921

  13. Prediction of new thermodynamically stable aluminum oxides

    CERN Document Server

    Liu, Yue; Wang, Shengnan; Zhu, Qiang; Dong, Xiao; Kresse, Georg

    2015-01-01

    Recently, it has been shown that under pressure, unexpected and counterintuitive chemical compounds become stable. Laser shock experiments (A. Rode, unpublished) on alumina (Al2O3) have shown non-equilibrium decomposition of alumina with the formation of free Al and a mysterious transparent phase. Inspired by these observations, with have explored the possibility of the formation of new chemical compounds in the system Al-O. Using the variable-composition structure prediction algorithm USPEX, in addition to the well-known Al2O3, we have found two extraordinary compounds Al4O7 and AlO2 to be thermodynamically stable in the pressure range 330-443 GPa and above 332 GPa, respectively. Both of these compounds at the same time contain oxide O2- and peroxide O22- ions, and both are insulating. Peroxo-groups are responsible for gap states, which significantly reduce the electronic band gap of both Al4O7 and AlO2.

  14. Anodic Oxidation in Aluminum Electrode by Using Hydrated Amorphous Aluminum Oxide Film as Solid Electrolyte under High Electric Field.

    Science.gov (United States)

    Yao, Manwen; Chen, Jianwen; Su, Zhen; Peng, Yong; Zou, Pei; Yao, Xi

    2016-05-01

    Dense and nonporous amorphous aluminum oxide (AmAO) film was deposited onto platinized silicon substrate by sol-gel and spin coating technology. The evaporated aluminum film was deposited onto the AmAO film as top electrode. The hydrated AmAO film was utilized as a solid electrolyte for anodic oxidation of the aluminum electrode (Al) film under high electric field. The hydrated AmAO film was a high efficiency electrolyte, where a 45 nm thick Al film was anodized completely on a 210 nm thick hydrated AmAO film. The current-voltage (I-V) characteristics and breakdown phenomena of a dry and hydrated 210 nm thick AmAO film with a 150 nm thick Al electrode pad were studied in this work. Breakdown voltage of the dry and hydrated 210 nm thick AmAO film were 85 ± 3 V (405 ± 14 MV m(-1)) and 160 ± 5 V (762 ± 24 MV m(-1)), respectively. The breakdown voltage of the hydrated AmAO film increased about twice, owing to the self-healing behavior (anodic oxidation reaction). As an intuitive phenomenon of the self-healing behavior, priority anodic oxidation phenomena was observed in a 210 nm thick hydrated AmAO film with a 65 nm thick Al electrode pad. The results suggested that self-healing behavior (anodic oxidation reaction) was occurring nearby the defect regions of the films during I-V test. It was an effective electrical self-healing method, which would be able to extend to many other simple and complex oxide dielectrics and various composite structures. PMID:27070754

  15. Radioluminescence of rare-earth doped aluminum oxide

    Energy Technology Data Exchange (ETDEWEB)

    Santiago, M.; Molina, P. [Universidad Nacional del Centro de la Provincia de Buenos Aires, Instituto de Fisica Arroyo Seco, Pinto 399, 7000 Tandil (Argentina); Barros, V. S.; Khoury, H. J.; Elihimas, D. R., E-mail: msantiag@exa.unicen.edu.ar [Universidade Federal de Pernambuco, Departamento de Energia Nuclear, Av. Prof. Luiz Freire 1000, Recife, PE 50740-540 (Brazil)

    2011-10-15

    Carbon-doped aluminum oxide (Al{sub 2}O{sub 3}:C) is one of the most used radioluminescence (Rl) materials for fiberoptic dosimetry due to its high efficiency and commercial availability. However, this compound presents the drawback of emitting in the spectral region, where the spurious radioluminescence of fibers is also important. In this work, the radioluminescence response of rare-earth doped Al{sub 2}O{sub 3} samples has been evaluated. The samples were prepared by mixing stoichiometric amounts of aluminum nitrate, urea and dopants with different amounts of terbium, samarium, cerium and thulium nitrates varying from 0 to 0.15 mo 1%. The influence of the different activators on the Rl spectra has been investigated in order to determine the feasibility of using these compounds for Rl fiberoptic dosimetry. (Author)

  16. CoPt patterned media in anodized aluminum oxide templates

    International Nuclear Information System (INIS)

    Patterned recording media consisting of a vertically aligned array of L10 phase CoPt nanowires embedded in a thin anodized aluminum oxide (AAO) template on silicon has been prepared. A sputter deposited thin film of aluminum on silicon was anodized and a CoPt magnetic alloy was electrodeposited into the pores of the AAO. The vertically aligned arrays of CoPt nanowires were about ∼100 nm tall with ∼20 nm average diameter. Since the CoPt nanowire array is laterally constrained by the surrounding AAO, the nanowire diameter is maintained without coarsening during the L10 phase conversion heat treatment at 700 deg. C. After annealing and conversion to the L10 phase, the ∼20 nm CoPt nanowires exhibit a large coercivity of ∼8 kOe measured in the in-plane and perpendicular directions

  17. Irradiation behavior of uranium oxide - Aluminum dispersion fuel

    International Nuclear Information System (INIS)

    An oxide version of the DART code has been generated in order to assess the irradiation behavior of UO2-Al dispersion fuel. The aluminum-fuel interaction models were developed based on U3O8-Al irradiation data. Deformation of the fuel element occurs due to fuel particle swelling driven by both solid and gaseous fission products and as a consequence of the interaction between the fuel particles and the aluminum matrix. The calculations show that, with the assumption that the correlations derived from U3O8 are valid for UO2, the LEU UO2-Al with a 42% fuel volume loading (4 g U/cm3 ) irradiated at fuel temperatures greater than 413 K should undergo breakaway swelling at core burnups greater than about 1.12 x 1027 fissions m-3 (∼63% 235U burnup). (author)

  18. Chemical Liquid Phase Deposition of Thin Aluminum Oxide Films

    Institute of Scientific and Technical Information of China (English)

    SUN,Jie(孙捷); SUN,Ying-Chun(孙迎春)

    2004-01-01

    Thin aluminum oxide films were deposited by a new and simple physicochemical method called chemical liquid phase deposition (CLD) on semiconductor materials. Aluminum sulfate with crystallized water and sodium bicarbonate were used as precursors for film growth, and the control of the system's pH value played an important role in this experiment. The growth rate is 12 nm/h with the deposition at [Al2(SO4)3]=0.0837 mol·L-1, [NaHCO3]=0.214 mol·L-1, 15 ℃. Post-growth annealing not only densifies and purifies the films, but results in film crystallization as well, Excellent quality of A12O3 films in this work is supported by electron dispersion spectroscopy,Fourier transform infrared spectrum, X-ray diffraction spectrum and scanning electron microscopy photograph.

  19. Comparative study of the growth of sputtered aluminum oxide films on organic and inorganic substrates

    OpenAIRE

    Sellner, Stefan; Gerlach, Alexander; Kowarik, Stefan; Schreiber, Frank; Dosch, Helmut; Meyer, Stephan; Pflaum, Jens; Ulbricht, Gerhard

    2007-01-01

    We present a comparative study of the growth of the technologically highly relevant gate dielectric and encapsulation material aluminum oxide in inorganic and also organic heterostructures. Atomic force microscopy studies indicate strong similarities in the surface morphology of aluminum oxide films grown on these chemically different substrates. In addition, from X-ray reflectivity measurements we extract the roughness exponent \\beta of aluminum oxide growth on both substrates. By renormalis...

  20. Standard specification for nuclear-grade aluminum oxide pellets

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2008-01-01

    1.1 This specification applies to pellets of aluminum oxide that may be ultimately used in a reactor core, for example, as filler or spacers within fuel, burnable poison, or control rods. In order to distinguish between the subject pellets and “burnable poison” pellets, it is established that the subject pellets are not intended to be used as neutron-absorbing material. 1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

  1. Chemical, mass spectrometric, and spectrochemical analysis of nuclear-grade aluminum oxide and aluminum oxide-boron carbide composite pellets

    Energy Technology Data Exchange (ETDEWEB)

    1981-01-01

    Aluminum oxide pellets are used in a reactor core as filler or spacers within fuel, burnable poison, or control rods. In order to be suitable for this purpose, the material must meet certain criteria for impurity content. The test methods in the standard are designed to show whether or not a given material meets these specifications. The following analytical procedures are described in detail: boron by titrimetry; separation of boron by mass spectrometry; isotopic composition by mass spectrometry; separation of halides by pyrohydrolysis; fluoride by ion-selective electrode; chloride, bromide, and iodide by amperometric microtitrimetry; trace elements by emission spectroscopy. (JMT)

  2. Nanosized Cobalt Oxides over Aluminum Monoliths for VOC Oxidation.

    Czech Academy of Sciences Publication Activity Database

    Jirátová, Květa; Kovanda, F.; Klempa, Jan; Balabánová, Jana

    Poznań: Poznan Science and Technology Park, 2016, P61. ISBN N. [Designing New Heterogeneous Catalysts: Faraday Discussion. London (GB), 04.04.2016-06.04.2016] R&D Projects: GA ČR GA14-13750S Institutional support: RVO:67985858 Keywords : cobalt oxides * Al monoliths * catalyst layer Subject RIV: CI - Industrial Chemistry, Chemical Engineering

  3. Formation of anodic aluminum oxide with serrated nanochannels.

    Science.gov (United States)

    Li, Dongdong; Zhao, Liang; Jiang, Chuanhai; Lu, Jia G

    2010-08-11

    We report a simple and robust method to self-assemble porous anodic aluminum oxide membranes with serrated nanochannels by anodizing in phosphoric acid solution. Due to high field conduction and anionic incorporation, an increase of anodizing voltage leads to an increase of the impurity levels and also the field strength across barrier layer. On the basis of both experiment and simulation results, the initiation and formation of serrated channels are attributed to the evolution of oxygen gas bubbles followed by plastic deformation in the oxide film. Alternating anodization in oxalic and phosphoric acids is applied to construct multilayered membranes with smooth and serrated channels, demonstrating a unique way to design and construct a three-dimensional hierarchical system with controllable morphology and composition. PMID:20617804

  4. Interfacial charging phenomena of aluminum (hydr)oxides

    Energy Technology Data Exchange (ETDEWEB)

    Hiemstra, T.; Yong, H.; Van Riemsdijk, W.H.

    1999-08-31

    The interfacial charging of Al(OH){sub 3} (gibbsite and bayerite) and Al{sub 2}O{sub 3} has been studied. For Al(OH){sub 3} it can be shown that the very strong variation in charging behavior for different preparations is related to the relative presence of differently reacting crystal planes. The edge faces of the hexagonal gibbsite crystals are proton reactive over the whole pH range, in contrast to the 001 plane, which is mainly uncharged below pH = 10. On this 001 face only doubly coordinated surface groups are found, in contrast to the edges which also have singly coordinated surface groups. The results are fully in agreement with the predictions of the Multi site complexation (MUSIC) model. The proton adsorption, electrolyte ion adsorption, and shift of the IEP of gibbsite and aluminum oxide have been modeled simultaneously. For gibbsite, the ion pair formation of Na is larger than that of Cl, as is evidenced by modeling the experimentally observed upward shift on the IEP and charge reversal at high electrolyte concentrations. All these experimental results can be satisfactorily modeled with the MUSIC model, including the experimental surface potential of aluminum oxide (ISFET).

  5. Corrosion evaluation of zirconium doped oxide coatings on aluminum formed by plasma electrolytic oxidation.

    Science.gov (United States)

    Bajat, Jelena; Mišković-Stanković, Vesna; Vasilić, Rastko; Stojadinović, Stevan

    2014-01-01

    The plasma electrolytic oxidation (PEO) of aluminum in sodium tungstate (Na(2)WO(4) · (2)H(2)O) and Na(2)WO(4) · (2)H(2)O doped with Zr was analyzed in order to obtain oxide coatings with improved corrosion resistance. The influence of current density in PEO process and anodization time was investigated, as well as the influence of Zr, with the aim to find out how they affect the chemical content, morphology, surface roughness, and corrosion stability of oxide coatings. It was shown that the presence of Zr increases the corrosion stability of oxide coatings for all investigated PEO times. Evolution of EIS spectra during the exposure to 3% NaCl, as a strong corrosive agent, indicated the highest corrosion stability for PEO coating formed on aluminum at 70 mA/cm(2) for 2 min in a zirconium containing electrolyte. PMID:25125114

  6. Comparative effects of macro-sized aluminum oxide and aluminum oxide nanoparticles on erythrocyte hemolysis: influence of cell source, temperature, and size

    International Nuclear Information System (INIS)

    Al2O3 is the most abundantly produced nanomaterial and has been used in diverse fields, including the medical, military, and industrial sectors. As there are concerns about the health effects of nanoparticles, it is important to understand how they interact with cells, and specifically with red blood cells. The hemolysis induced by three commercial nano-sized aluminum oxide particles (nanopowder 13 nm, nanopowder <50 nm, and nanowire 2–6 × 200–400 nm) was compared to aluminum oxide and has been studied on erythrocytes from humans, rats, and rabbits, in order to elucidate the mechanism of action and the influence of size and shape on hemolytic behavior. The concentrations inducing 50 % hemolysis (HC50) were calculated for each compound studied. The most hemolytic aluminum oxide particles were of nanopowder 13, followed by nanowire and nanopowder 50. The addition of albumin to PBS induced a protective effect on hemolysis in all the nano-forms of Al2O3, but not on Al2O3. The drop in HC50 correlated to a decrease in nanomaterial size, which was induced by a reduction of aggregation. Aluminum oxide nanoparticles are less hemolytic than other oxide nanoparticles and behave differently depending on the size and shape of the nanoparticles. The hemolytic behavior of aluminum oxide nanoparticles differs from that of aluminum oxide

  7. Comparative effects of macro-sized aluminum oxide and aluminum oxide nanoparticles on erythrocyte hemolysis: influence of cell source, temperature, and size

    Energy Technology Data Exchange (ETDEWEB)

    Vinardell, M. P., E-mail: mpvinardellmh@ub.edu; Sordé, A. [Universitat de Barcelona, Departament de Fisiologia, Facultat de Farmàcia (Spain); Díaz, J. [Universitat de Barcelona CCiT, Scientific and Technological Centers (Spain); Baccarin, T.; Mitjans, M. [Universitat de Barcelona, Departament de Fisiologia, Facultat de Farmàcia (Spain)

    2015-02-15

    Al{sub 2}O{sub 3} is the most abundantly produced nanomaterial and has been used in diverse fields, including the medical, military, and industrial sectors. As there are concerns about the health effects of nanoparticles, it is important to understand how they interact with cells, and specifically with red blood cells. The hemolysis induced by three commercial nano-sized aluminum oxide particles (nanopowder 13 nm, nanopowder <50 nm, and nanowire 2–6 × 200–400 nm) was compared to aluminum oxide and has been studied on erythrocytes from humans, rats, and rabbits, in order to elucidate the mechanism of action and the influence of size and shape on hemolytic behavior. The concentrations inducing 50 % hemolysis (HC{sub 50}) were calculated for each compound studied. The most hemolytic aluminum oxide particles were of nanopowder 13, followed by nanowire and nanopowder 50. The addition of albumin to PBS induced a protective effect on hemolysis in all the nano-forms of Al{sub 2}O{sub 3}, but not on Al{sub 2}O{sub 3}. The drop in HC{sub 50} correlated to a decrease in nanomaterial size, which was induced by a reduction of aggregation. Aluminum oxide nanoparticles are less hemolytic than other oxide nanoparticles and behave differently depending on the size and shape of the nanoparticles. The hemolytic behavior of aluminum oxide nanoparticles differs from that of aluminum oxide.

  8. Electrochemical fabrication of CdS/Co nanowire arrays in porous aluminum oxide templates

    CERN Document Server

    Yoon, C H

    2002-01-01

    A procedure for preparing semiconductor/metal nanowire arrays is described, based on a template method which entails electrochemical deposition into nanometer-wide parallel pores of anodic aluminum oxide films on aluminum. Aligned CdS/Co heterostructured nanowires have been prepared by ac electrodeposition in the anodic aluminum oxide templates. By varying the preparation conditions, a variety of CdS/Co nanowire arrays were fabricated, whose dimensional properties could be adjusted.

  9. The Electrical and Mechanical Properties of Porous Anodic 6061-T6 Aluminum Alloy Oxide Film

    OpenAIRE

    Tsung-Chieh Cheng; Chu-Chiang Chou

    2015-01-01

    The properties of the growth of the 6061-T6 aluminum alloy oxide were studied using sulfuric acid anodization. The parameters for the manufacturing process include electrolyte categories, electrolyte concentration, and operating voltages. The results showed that the aluminum oxides obtained by anodization process are mainly amorphous structure and the anodic current density is an important factor affecting the rate of response for oxygen and aluminum ions in barrier. In this experiment, polis...

  10. Development of Pinhole-Free Amorphous Aluminum Oxide Protective Layers for Biomedical Device Applications

    OpenAIRE

    Litvinov, Julia; Wang, Yi-Ju; George, Jinnie; Chinwangso, Pawilai; Brankovic, Stanko; Willson, Richard C.; Litvinov, Dmitri

    2013-01-01

    This paper describes synthesis of ultrathin pinhole-free insulating aluminum oxide layers for electronic device protection in corrosive liquid environments, such as phosphate buffered saline (PBS) or clinical fluids, to enable emerging biomedical applications such as biomolecular sensors. A pinhole-free 25-nm thick amorphous aluminum oxide layer has been achieved using ultra-high vacuum DC magnetron reactive sputtering of aluminum in oxygen/argon plasma followed by oxygen plasma post-processi...

  11. Aluminum Oxide Formation On Fecral Catalyst Support By Electro-Chemical Coating

    Directory of Open Access Journals (Sweden)

    Yang H.S.

    2015-06-01

    Full Text Available FeCrAl is comprised essentially of Fe, Cr, Al and generally considered as metallic substrates for catalyst support because of its advantage in the high-temperature corrosion resistance, high mechanical strength, and ductility. Oxidation film and its adhesion on FeCrAl surface with aluminum are important for catalyst life. Therefore various appropriate surface treatments such as thermal oxidation, Sol, PVD, CVD has studied. In this research, PEO (plasma electrolytic oxidation process was applied to form the aluminum oxide on FeCrAl surface, and the formed oxide particle according to process conditions such as electric energy and oxidation time were investigated. Microstructure and aluminum oxide particle on FeCrAl surface after PEO process was observed by FE-SEM and EDS with element mapping analysis. The study presents possibility of aluminum oxide formation by electro-chemical coating process without any pretreatment of FeCrAl.

  12. Astaxanthin ameliorates aluminum chloride-induced spatial memory impairment and neuronal oxidative stress in mice.

    Science.gov (United States)

    Al-Amin, Md Mamun; Reza, Hasan Mahmud; Saadi, Hasan Mahmud; Mahmud, Waich; Ibrahim, Abdirahman Adam; Alam, Musrura Mefta; Kabir, Nadia; Saifullah, A R M; Tropa, Sarjana Tarannum; Quddus, A H M Ruhul

    2016-04-15

    Aluminum chloride induces neurodegenerative disease in animal model. Evidence suggests that aluminum intake results in the activation of glial cells and generation of reactive oxygen species. By contrast, astaxanthin is an antioxidant having potential neuroprotective activity. In this study, we investigate the effect of astaxanthin on aluminum chloride-exposed behavioral brain function and neuronal oxidative stress (OS). Male Swiss albino mice (4 months old) were divided into 4 groups: (i) control (distilled water), (ii) aluminum chloride, (iii) astaxanthin+aluminum chloride, and (iv) astaxanthin. Two behavioral tests; radial arm maze and open field test were conducted, and OS markers were assayed from the brain and liver tissues following 42 days of treatment. Aluminum exposed group showed a significant reduction in spatial memory performance and anxiety-like behavior. Moreover, aluminum group exhibited a marked deterioration of oxidative markers; lipid peroxidation (MDA), nitric oxide (NO), glutathione (GSH) and advanced oxidation of protein products (AOPP) in the brain. To the contrary, co-administration of astaxanthin and aluminum has shown improved spatial memory, locomotor activity, and OS. These results indicate that astaxanthin improves aluminum-induced impaired memory performances presumably by the reduction of OS in the distinct brain regions. We suggest a future study to determine the underlying mechanism of astaxanthin in improving aluminum-exposed behavioral deficits. PMID:26927754

  13. A study of hydrogen permeation in aluminum alloy treated by various oxidation processes

    International Nuclear Information System (INIS)

    A set of oxide coatings was formed on the surface of an Al alloy (wt%: Fe, 0.24; Si, 1.16; Cu, 0.05-0.2; Zn, 0.1; Al, residual) by means of various oxidation processes. The hydrogen permeability through the aluminum alloy and its coating materials was determined by a vapor phase permeation technique at temperatures ranging from 400 to 500 C using high-purity H2 (99.9999%) gas with an upstream hydrogen pressure of 104-105 Pa. The experimental results show that the hydrogen permeability through aluminum oxide coating is 100-2000 times lower than that through the aluminum alloy substrate. This means that the aluminum oxide is a significant hydrogen permeation barrier. A high hydrogen permeation resistance was observed in an oxide layer prefilmed in 200 C water, while an anodized aluminum oxide film had a less obstructive effect, possibly caused by the porous structure of the anodic oxide. The hydrogen permeability through films of aluminum oxide was not a simple function of the aluminum-oxide phase configuration. (orig.)

  14. Enhanced photocatalytic activity of electrochemically synthesized aluminum oxide nanoparticles

    Science.gov (United States)

    Pathania, Deepak; Katwal, Rishu; Kaur, Harpreet

    2016-03-01

    In this study, aluminum oxide (Al2O3) nanoparticles (NPs) were synthesized via an electrochemical method. The effects of reaction parameters such as supporting electrolytes, solvent, current and electrolysis time on the shape and size of the resulting NPs were investigated. The Al2O3 NPs were characterized by Fourier transform infrared spectroscopy, X-ray diffraction, transmission electron microscopy, thermogravimetric analysis/differential thermal analysis, energy-dispersive X-ray analysis, and ultraviolet-visible spectroscopy. Moreover, the Al2O3 NPs were explored for photocatalytic degradation of malachite green (MG) dye under sunlight irradiation via two processes: adsorption followed by photocatalysis; coupled adsorption and photocatalysis. The coupled process exhibited a higher photodegradation efficiency (45%) compared to adsorption followed by photocatalysis (32%). The obtained kinetic data was well fitted using a pseudo-first-order model for MG degradation.

  15. Amorphous coatings deposited on aluminum alloy by plasma electrolytic oxidation

    Institute of Scientific and Technical Information of China (English)

    GUAN Yong-jun; XIA Yuan

    2005-01-01

    Amorphous [Al-Si-O] coatings were deposited on aluminum alloy by plasma electrolytic oxidation (PEO). The process parameters, composition, micrograph, and mechanical property of PEO amorphous coatings were investigated. It is found that the growth rate of PEO coatings reaches 4.44 μm/min if the current density is 0.9 mA/mm2. XRD results show that the PEO coatings are amorphous in the current density range of 0.3 - 0.9mA/mm2. EDS results show that the coatings are composed of O, Si and Al elements. SEM results show that the coatings are porous. Nano indentation results show that the hardness of the coatings is about 3 - 4 times of that of the substrate, while the elastic modulus is about the same with the substrate. Furthermore, a formation mechanism of amorphous PEO coatings was proposed.

  16. Fabrication of YBCO nanowires with anodic aluminum oxide (AAO) template

    Energy Technology Data Exchange (ETDEWEB)

    Dadras, Sedigheh, E-mail: dadras@alzahra.ac.ir; Aawani, Elaheh

    2015-10-15

    We have fabricated YBCO nanowires by using anodic aluminum oxide (AAO) template and sol–gel method, to investigate the fundamental properties of the one-dimensional nanostructure YBCO high-temperature superconductor and enhance its applications. The field-emission scanning electron microscopy and X-ray diffraction pattern results have shown forming of Y-123 nanowires in the template. As an outcome, the YBCO nanowires, prepared by dipping AAO template into YBCO sol method, have average diameter of about 38 nm and length of 1 μm; this is an optimum nanowire sample with larger diameter and length. The resistance–temperature measurement indicates that the onset critical temperature of these samples occurs at 91 K, and the resistance of the optimum sample at onset transition is 10 times lower than the other sample.

  17. Fabrication of Nanostructured PLGA Scaffolds Using Anodic Aluminum Oxide Templates

    CERN Document Server

    Hsueh, Cheng-Chih; Hsu, Shan-Hui; Hung, Huey-Shan

    2008-01-01

    PLGA (poly(lactic-co-glycolic acid)) is one of the most used biodegradable and biocompatible materials. Nanostructured PLGA even has great application potentials in tissue engineering. In this research, a fabrication technique for nanostructured PLGA membrane was investigated and developed. In this novel fabrication approach, an anodic aluminum oxide (AAO) film was use as the template ; the PLGA solution was then cast on it ; the vacuum air-extraction process was applied to transfer the nano porous pattern from the AAO membrane to the PLGA membrane and form nanostures on it. The cell culture experiments of the bovine endothelial cells demonstrated that the nanostructured PLGA membrane can double the cell growing rate. Compared to the conventional chemical-etching process, the physical fabrication method proposed in this research not only is simpler but also does not alter the characteristics of the PLGA. The nanostructure of the PLGA membrane can be well controlled by the AAO temperate.

  18. Development of Pinhole-Free Amorphous Aluminum Oxide Protective Layers for Biomedical Device Applications.

    Science.gov (United States)

    Litvinov, Julia; Wang, Yi-Ju; George, Jinnie; Chinwangso, Pawilai; Brankovic, Stanko; Willson, Richard C; Litvinov, Dmitri

    2013-06-15

    This paper describes synthesis of ultrathin pinhole-free insulating aluminum oxide layers for electronic device protection in corrosive liquid environments, such as phosphate buffered saline (PBS) or clinical fluids, to enable emerging biomedical applications such as biomolecular sensors. A pinhole-free 25-nm thick amorphous aluminum oxide layer has been achieved using ultra-high vacuum DC magnetron reactive sputtering of aluminum in oxygen/argon plasma followed by oxygen plasma post-processing. Deposition parameters were optimized to achieve the best corrosion protection of lithographically defined device structures. Electrochemical deposition of copper through the aluminum oxide layers was used to detect the presence (or absence) of pinholes. FTIR, XPS, and spectroscopic ellipsometry were used to characterize the material properties of the protective layers. Electrical resistance of the copper device structures protected by the aluminum oxide layers and exposed to a PBS solution was used as a metric to evaluate the long-term stability of these device structures. PMID:23682201

  19. In-flight oxidation of aluminum in the twin-wire electric arc process

    Science.gov (United States)

    Guillen, Donna Post; Williams, Brian G.

    2006-03-01

    This paper examines the in-flight oxidation of aluminum sprayed in air using the twin-wire electric arc (TWEA) thermal spray process. Aerodynamic shear at the droplet surface increases the amount of in-flight oxidation by promoting entrainment of the surface oxides within the molten droplet and continually exposing fresh fluid available for oxidation. Mathematical predictions herein confirm experimental measurements that reveal an elevated, nearly constant surface temperature (˜2273 K) of the droplets during flight. The calculated oxide volume fraction of a “typical” droplet with internal circulation compares favorably to the experimentally determined oxide content (3.3 12.7%) for a typical TWEA-sprayed aluminum coating sprayed onto a room temperature substrate. It is concluded that internal circulation within the molten aluminum droplet is a significant source of oxidation. This effect produces an oxide content nearly two orders of magnitude larger than that of a droplet without continual oxidation.

  20. Photochemistry of adsorbed nitrate on aluminum oxide particle surfaces.

    Science.gov (United States)

    Rubasinghege, Gayan; Grassian, Vicki H

    2009-07-01

    Nitrogen oxides, including nitrogen dioxide and nitric acid, react with mineral dust particles in the atmosphere to yield adsorbed nitrate. Although nitrate ion is a well-known chromophore in natural waters, little is known about the surface photochemistry of nitrate adsorbed on mineral particles. In this study, nitrate adsorbed on aluminum oxide, a model system for mineral dust aerosol, is irradiated with broadband light (lambda > 300 nm) as a function of relative humidity (RH) in the presence of molecular oxygen. Upon irradiation, the nitrate ion readily undergoes photolysis to yield nitrogen-containing gas-phase products including NO(2), NO, and N(2)O, with NO being the major product. The relative ratio and product yields of these gas-phase products change with RH, with N(2)O production being highest at the higher relative humidities. Furthermore, an efficient dark reaction readily converts the major NO product into NO(2) during post-irradiation. Photochemical processes on mineral dust aerosol surfaces have the potential to impact the chemical balance of the atmosphere, yet little is known about these processes. In this study, the impact that adsorbed nitrate photochemistry may have on the renoxification of the atmosphere is discussed. PMID:19534452

  1. Aluminum ions accelerated the oxidative stress of copper-mediated melanin formation

    Science.gov (United States)

    Di, Junwei; Bi, Shuping

    2003-11-01

    A comparison between the effects of aluminum and cupric ions on the dopachrome (DC) conversion and the cooperation effect of the both ions in the DOPA oxidation to melanin pathway has been studied by UV-Vis spectrophotometric method. Both aluminum and cupric ions catalyze the DC conversion reaction, which is an important step in the melanin synthesis pathway. However, cupric ions catalyze the conversion of DC to yield 5,6-dihydroxyindole-2-carboxylic acid (DHICA) but the product of DC conversion catalyzed by aluminum is 5,6-dihydroxyindole (DHI). DOPA oxidation catalyzed by aluminum and cupric ions is studied in the presence of hydrogen peroxide. The results from our experiments provide evidence that aluminum can markedly increase the oxidative stress of copper-mediated the melanin formation and influence the properties of the melanin by means of changing the ratio of DHICA/DHI in the acidic environment (pH 5.5).

  2. Effect of anneal pre-treatment of polycrystalline aluminum sheets on synthesis of highly-ordered anodic aluminum oxide membranes

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Anodic aluminum oxide (AAO) membranes with large ordered pore domains were successfully prepared by adopting the anneal pre-treatment of polycrystalline alu- minum sheets. A statistical method with Gaussian distribution was introduced to quantitatively study the size of the domain with ordered pores. The largest average area of ordered pore domains was 2.6 μm2±0.11 μm2. The corresponding AAO membrane was synthesized by aluminum sheets annealed at 893 K for 24 h.

  3. Surface enhanced Raman scattering of biospecies on anodized aluminum oxide films

    Science.gov (United States)

    Zhang, C.; Smirnov, A. I.; Hahn, D.; Grebel, H.

    2007-06-01

    Traditionally, aluminum and anodized aluminum oxide films (AAO) are not the platforms of choice for surface-enhanced raman scattering (SERS) experiments despite of the aluminum's large negative permittivity value. Here we examine the usefulness of aluminum and nanoporous alumina platforms for detecting soft biospecies ranging from bacterial spores to protein markers. We used these flat platforms to examine SERS of a model protein (cytochrome c from bovine heart tissue) and bacterial cells (spores of Bacillus subtilis ATCC13933 used as Anthrax simulant) and demonstrated clear Raman amplification.

  4. Discharge behaviors during plasma electrolytic oxidation on aluminum alloy

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Run [Key Laboratory for Beam Technology and Materials Modification of Ministry of Education, College of Nuclear Science and Technology, Beijing Normal University, Beijing 100875 (China); Beijing Radiation Center, Beijing 100875 (China); Zhenjiang Watercraft College, Zhenjiang 212000, Jiangsu (China); Wu, Jie [Key Laboratory for Beam Technology and Materials Modification of Ministry of Education, College of Nuclear Science and Technology, Beijing Normal University, Beijing 100875 (China); Beijing Radiation Center, Beijing 100875 (China); Xue, Wenbin, E-mail: xuewb@bnu.edu.cn [Key Laboratory for Beam Technology and Materials Modification of Ministry of Education, College of Nuclear Science and Technology, Beijing Normal University, Beijing 100875 (China); Beijing Radiation Center, Beijing 100875 (China); Qu, Yao; Yang, Chaolin; Wang, Bin; Wu, Xianying [Key Laboratory for Beam Technology and Materials Modification of Ministry of Education, College of Nuclear Science and Technology, Beijing Normal University, Beijing 100875 (China); Beijing Radiation Center, Beijing 100875 (China)

    2014-11-14

    A plasma electrolytic oxidation (PEO) process was performed on the 2024 aluminum alloy in silicate electrolyte to fabricate ceramic coatings under a constant voltage. Optical emission spectroscopy (OES) was employed to evaluate the characteristics of plasma discharge during PEO process. The plasma electron temperature and density were obtained by analyzing the spectral lines of OES, and the atomic ionization degree in discharge zone was calculated in terms of Saha thermal ionization equation. The illumination intensity of plasma discharge and the temperature in the interior of alloy were measured. Combining the surface morphology and cross-sectional microstructure with the optical emission spectra and illumination at different discharge stage, a discharge model in the growth of PEO ceramic coatings was proposed. It is found that there are two discharge modes of type A with small spark size and type B with large spark size, and the latter only appears in the intermediate stage of PEO process. The illumination intensity has a maximum value in the initial stage of oxidation with many sparks of discharge type A. The electron temperature in plasma discharge zone is about 3000 K–7000 K and atomic ionization degree of Al is about 2.0 × 10{sup −5}–7.2 × 10{sup −3}, which depend on discharge stage. The discharge type B plays a key role on the electron temperature and atomic ionization degree. The electron density keeps stable in the range of about 8.5 × 10{sup 21} m{sup −3}–2.6 × 10{sup 22} m{sup −3}. - Highlights: • The characteristics of PEO plasma discharge was evaluated by OES. • Electron temperature, concentration, atomic ionization degree were calculated. • Discharge model for the growth of PEO coatings was proposed. • Temperature in the interior of alloy during PEO process was measured.

  5. A method to study the history of a double oxide film defect in liquid aluminum alloys

    Science.gov (United States)

    Raiszadeh, R.; Griffiths, W. D.

    2006-12-01

    Entrained double oxide films have been held responsible for reductions in mechanical properties in aluminum casting alloys. However, their behavior in the liquid metal, once formed, has not been studied directly. It has been proposed that the atmosphere entrapped in the double oxide film defect will continue to react with the liquid metal surrounding it, perhaps leading to its elimination as a significant defect. A silicon-nitride rod with a hole in one end was plunged into liquid aluminum to hold a known volume of air in contact with the liquid metal at a constant temperature. The change in the air volume with time was recorded by real-time X-ray radiography to determine the reaction rates of the trapped atmosphere with the liquid aluminum, creating a model for the behavior of an entrained double oxide film defect. The results from this experiment showed that first oxygen, and then nitrogen, was consumed by the aluminum alloy, to form aluminum oxide and aluminum nitride, respectively. The effect of adding different elements to the liquid aluminum and the effect of different hydrogen contents were also studied.

  6. Passivation effects of atomic-layer-deposited aluminum oxide

    Directory of Open Access Journals (Sweden)

    Kotipalli R.

    2013-09-01

    Full Text Available Atomic-layer-deposited (ALD aluminum oxide (Al2O3 has recently demonstrated an excellent surface passivation for both n- and p-type c-Si solar cells thanks to the presence of high negative fixed charges (Qf ~ 1012−1013 cm-2 in combination with a low density of interface states (Dit. This paper investigates the passivation quality of thin (15 nm Al2O3 films deposited by two different techniques: plasma-enhanced atomic layer deposition (PE-ALD and Thermal atomic layer deposition (T-ALD. Other dielectric materials taken into account for comparison include: thermally-grown silicon dioxide (SiO2 (20 nm, SiO2 (20 nm deposited by plasma-enhanced chemical vapour deposition (PECVD and hydrogenated amorphous silicon nitride (a-SiNx:H (20 nm also deposited by PECVD. With the above-mentioned dielectric layers, Metal Insulator Semiconductor (MIS capacitors were fabricated for Qf and Dit extraction through Capacitance-Voltage-Conductance (C-V-G measurements. In addition, lifetime measurements were carried out to evaluate the effective surface recombination velocity (SRV. The influence of extracted C-V-G parameters (Qf,Dit on the injection dependent lifetime measurements τ(Δn, and the dominant passivation mechanism involved have been discussed. Furthermore we have also studied the influence of the SiO2 interfacial layer thickness between the Al2O3 and silicon surface on the field-effect passivation mechanism. It is shown that the field effect passivation in accumulation mode is more predominant when compared to surface defect passivation.

  7. Interaction of ester functional groups with aluminum oxide surfaces studied using infrared reflection absorption spectroscopy.

    Science.gov (United States)

    van den Brand, J; Blajiev, O; Beentjes, P C J; Terryn, H; de Wit, J H W

    2004-07-20

    The bonding of two types of ester group-containing molecules with a set of different oxide layers on aluminum has been investigated using infrared reflection absorption spectroscopy. The different oxide layers were made by giving typical surface treatments to the aluminum substrate. The purpose of the investigation was to find out what type of ester-oxide bond is formed and whether this is influenced by changes in the composition and chemistry of the oxide. The extent by which these bonded ester molecules resisted disbondment in water or substitution by molecules capable of chemisorption was also investigated. The ester groups were found to show hydrogen bonding with hydroxyls on the oxide surfaces through their carbonyl oxygens. For all oxides, the ester groups showed the same nu(C = O) carbonyl stretching vibration after adsorption, indicating very similar bonding occurs. However, the oxides showed differences in the amount of molecules bonded to the oxide surface, and a clear relation was observed with the hydroxyl concentration present on the oxide surface, which was determined from XPS measurements. The two compounds showed differences in the free to bonded nu(C = O) infrared peak shift, indicating differences in bonding strength with the oxide surface between the two types of molecules. The bonding of the ester groups with the oxide surfaces was found to be not stable in the presence of water and also not in the presence of a compound capable of chemisorption with the aluminum oxide surface. PMID:15248718

  8. Improvement of plasmonic enhancement of quantum dot emission via an intermediate silicon-aluminum oxide interface

    International Nuclear Information System (INIS)

    We studied the emission of quantum dots in the presence of plasmon-metal oxide substrates, which consist of arrays of metallic nanorods embedded in amorphous silicon coated with a nanometer-thin layer of aluminum oxide on the top. We showed that the combined effects of plasmons and the silicon-aluminum oxide interface can lead to significant enhancement of the quantum efficiency of quantum dots. Our results show that such an interface can significantly enhance plasmonic effects of the nanorods via quantum dot-induced exciton-plasmon coupling, leading to partial polarization of the quantum dots' emission

  9. Niobium-aluminum base alloys having improved, high temperature oxidation resistance

    Science.gov (United States)

    Hebsur, Mohan G. (Inventor); Stephens, Joseph R. (Inventor)

    1991-01-01

    A niobium-aluminum base alloy having improved oxidation resistance at high temperatures and consisting essentially of 48%-52% niobium, 36%-42% aluminum, 4%-10% chromium, 0%-2%, more preferably 1%-2%, silicon and/or tungsten with tungsten being preferred, and 0.1%-2.0% of a rare earth selected from the group consisting of yttrium, ytterbium and erbium. Parabolic oxidation rates, k.sub.p, at 1200.degree. C. range from about 0.006 to 0.032 (mg/cm.sup.2).sup.2 /hr. The new alloys also exhibit excellent cyclic oxidation resistance.

  10. Optical Anisotropy and Porosity of Anodic Aluminum Oxide Characterized by Spectroscopic Ellipsometry

    NARCIS (Netherlands)

    Kooij, E. Stefan; Wormeester, Herbert; Galca, Aurelian C.; Poelsema, Bene

    2003-01-01

    Anodic oxidation of aluminum results in a mesoporous oxide film. The thin-film geometry of our samples enables straightforward optical modeling of ellipsometry spectra of fully anodized films, using only three physically relevant parameters. The system of randomly distributed, but aligned cylindrica

  11. Murine pulmonary responses after sub-chronic exposure to aluminum oxide-based nanowhiskers

    OpenAIRE

    Adamcakova-Dodd Andrea; Stebounova Larissa V; O’Shaughnessy Patrick T; Kim Jong; Grassian Vicki H; Thorne Peter S

    2012-01-01

    Abstract Background Aluminum oxide-based nanowhiskers (AO nanowhiskers) have been used in manufacturing processes as catalyst supports, flame retardants, adsorbents, or in ceramic, metal and plastic composite materials. They are classified as high aspect ratio nanomaterials. Our aim was to assess in vivo toxicity of inhaled AO nanowhisker aerosols. Methods Primary dimensions of AO nanowhiskers specified by manufacturer were 2–4 nm x 2800 nm. The aluminum content found in this nanomaterial was...

  12. Electrophoretic deposition of PTFE particles on porous anodic aluminum oxide film and its tribological properties

    International Nuclear Information System (INIS)

    Polytetrafluoroethylene (PTFE) composite film was successfully fabricated by depositing PTFE particles into porous anodic aluminum oxide film using electrophoretic deposition (EPD) process. Firstly, porous anodic aluminum oxide film was synthesized by anodic oxidation process in sulphuric acid electrolyte. Then, PTFE particles in suspension were directionally deposited into the porous substrate. Finally, a heat treatment at 300 °C for 1 h was utilized to enhance PTFE particles adhesion to the substrate. The influence of anodic oxidation parameters on the morphology and micro-hardness of the porous anodic aluminum oxide film was studied and the PTFE particles deposited into the pores were authenticated using energy-dispersive spectrometer (EDS) and scanning electron microscopy (SEM). Tribological properties of the PTFE composite film were investigated under dry sliding. The experimental results showed that the composite film exhibit remarkable low friction. The composite film had friction coefficient of 0.20 which deposited in 15% PTFE emulsion at temperature of 15 °C and current density of 3 A/dm2 for 35 min. In addition, a control specimen of porous anodic aluminum oxide film and the PTFE composite film were carried out under the same test condition, friction coefficient of the PTFE composite film was reduced by 60% comparing with the control specimen at 380 MPa and 100 mm/s. The lubricating mechanism was that PTFE particles embedded in porous anodic aluminum oxide film smeared a transfer film on the sliding path and the micro-pores could support the supplement of solid lubricant during the sliding, which prolonged the lubrication life of the aluminum alloys.

  13. Electrophoretic deposition of PTFE particles on porous anodic aluminum oxide film and its tribological properties

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Dongya; Dong, Guangneng, E-mail: donggn@mail.xjtu.edu.cn; Chen, Yinjuan; Zeng, Qunfeng

    2014-01-30

    Polytetrafluoroethylene (PTFE) composite film was successfully fabricated by depositing PTFE particles into porous anodic aluminum oxide film using electrophoretic deposition (EPD) process. Firstly, porous anodic aluminum oxide film was synthesized by anodic oxidation process in sulphuric acid electrolyte. Then, PTFE particles in suspension were directionally deposited into the porous substrate. Finally, a heat treatment at 300 °C for 1 h was utilized to enhance PTFE particles adhesion to the substrate. The influence of anodic oxidation parameters on the morphology and micro-hardness of the porous anodic aluminum oxide film was studied and the PTFE particles deposited into the pores were authenticated using energy-dispersive spectrometer (EDS) and scanning electron microscopy (SEM). Tribological properties of the PTFE composite film were investigated under dry sliding. The experimental results showed that the composite film exhibit remarkable low friction. The composite film had friction coefficient of 0.20 which deposited in 15% PTFE emulsion at temperature of 15 °C and current density of 3 A/dm{sup 2} for 35 min. In addition, a control specimen of porous anodic aluminum oxide film and the PTFE composite film were carried out under the same test condition, friction coefficient of the PTFE composite film was reduced by 60% comparing with the control specimen at 380 MPa and 100 mm/s. The lubricating mechanism was that PTFE particles embedded in porous anodic aluminum oxide film smeared a transfer film on the sliding path and the micro-pores could support the supplement of solid lubricant during the sliding, which prolonged the lubrication life of the aluminum alloys.

  14. Electrophoretic deposition of PTFE particles on porous anodic aluminum oxide film and its tribological properties

    Science.gov (United States)

    Zhang, Dongya; Dong, Guangneng; Chen, Yinjuan; Zeng, Qunfeng

    2014-01-01

    Polytetrafluoroethylene (PTFE) composite film was successfully fabricated by depositing PTFE particles into porous anodic aluminum oxide film using electrophoretic deposition (EPD) process. Firstly, porous anodic aluminum oxide film was synthesized by anodic oxidation process in sulphuric acid electrolyte. Then, PTFE particles in suspension were directionally deposited into the porous substrate. Finally, a heat treatment at 300 °C for 1 h was utilized to enhance PTFE particles adhesion to the substrate. The influence of anodic oxidation parameters on the morphology and micro-hardness of the porous anodic aluminum oxide film was studied and the PTFE particles deposited into the pores were authenticated using energy-dispersive spectrometer (EDS) and scanning electron microscopy (SEM). Tribological properties of the PTFE composite film were investigated under dry sliding. The experimental results showed that the composite film exhibit remarkable low friction. The composite film had friction coefficient of 0.20 which deposited in 15% PTFE emulsion at temperature of 15 °C and current density of 3 A/dm2 for 35 min. In addition, a control specimen of porous anodic aluminum oxide film and the PTFE composite film were carried out under the same test condition, friction coefficient of the PTFE composite film was reduced by 60% comparing with the control specimen at 380 MPa and 100 mm/s. The lubricating mechanism was that PTFE particles embedded in porous anodic aluminum oxide film smeared a transfer film on the sliding path and the micro-pores could support the supplement of solid lubricant during the sliding, which prolonged the lubrication life of the aluminum alloys.

  15. Structural features of anodic oxide films formed on aluminum substrate coated with self-assembled microspheres

    Energy Technology Data Exchange (ETDEWEB)

    Asoh, Hidetaka [Department of Applied Chemistry, Faculty of Engineering, Kogakuin University, 2665-1 Nakano, Hachioji, Tokyo 192-0015 (Japan)], E-mail: asoh@cc.kogakuin.ac.jp; Uchibori, Kota; Ono, Sachiko [Department of Applied Chemistry, Faculty of Engineering, Kogakuin University, 2665-1 Nakano, Hachioji, Tokyo 192-0015 (Japan)

    2009-07-15

    The structural features of anodic oxide films formed on an aluminum substrate coated with self-assembled microspheres were investigated by scanning electron microscopy and atomic force microscopy. In the first anodization in neutral solution, the growth of a barrier-type film was partially suppressed in the contact area between the spheres and the underlying aluminum substrate, resulting in the formation of ordered dimple arrays in an anodic oxide film. After the subsequent second anodization in acid solution at a voltage lower than that of the first anodization, nanopores were generated only within each dimple. The nanoporous region could be removed selectively by post-chemical etching using the difference in structural dimensions between the porous region and the surrounding barrier region. The mechanism of anodic oxide growth on the aluminum substrate coated with microspheres through multistep anodization is discussed.

  16. Atmospheric pressure plasma enhanced chemical vapor deposition of zinc oxide and aluminum zinc oxide

    International Nuclear Information System (INIS)

    Zinc oxide (ZnO) and aluminum-doped zinc oxide (AZO) thin films were deposited via atmospheric pressure plasma enhanced chemical vapor deposition. A second-generation precursor, bis(1,1,1,5,5,5-hexafluoro-2,4-pentanedionato)(N,N′-diethylethylenediamine) zinc, exhibited significant vapor pressure and good stability at one atmosphere where a vaporization temperature of 110 °C gave flux ∼ 7 μmol/min. Auger electron spectroscopy confirmed that addition of H2O to the carrier gas stream mitigated F contamination giving nearly 1:1 metal:oxide stoichiometries for both ZnO and AZO with little precursor-derived C contamination. ZnO and AZO thin film resistivities ranged from 14 to 28 Ω·cm for the former and 1.1 to 2.7 Ω·cm for the latter. - Highlights: • A second generation precursor was utilized for atmospheric pressure film growth. • Addition of water vapor to the carrier gas stream led to a marked reduction of ZnF2. • Carbonaceous contamination from the precursor was minimal

  17. Atmospheric pressure plasma enhanced chemical vapor deposition of zinc oxide and aluminum zinc oxide

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, Kyle W. [Center for Nanoscale Science and Engineering, North Dakota State University, Fargo, ND (United States); Department of Mechanical Engineering, North Dakota State University, Fargo, ND (United States); Guruvenket, Srinivasan; Sailer, Robert A. [Center for Nanoscale Science and Engineering, North Dakota State University, Fargo, ND (United States); Ahrenkiel, S. Phillip [Department of Nanoscience and Nanoengineering, South Dakota School of Mines and Technology, Rapid City, SD (United States); Schulz, Douglas L., E-mail: SBRconsulting@hotmail.com [Center for Nanoscale Science and Engineering, North Dakota State University, Fargo, ND (United States); Department of Mechanical Engineering, North Dakota State University, Fargo, ND (United States)

    2013-12-02

    Zinc oxide (ZnO) and aluminum-doped zinc oxide (AZO) thin films were deposited via atmospheric pressure plasma enhanced chemical vapor deposition. A second-generation precursor, bis(1,1,1,5,5,5-hexafluoro-2,4-pentanedionato)(N,N′-diethylethylenediamine) zinc, exhibited significant vapor pressure and good stability at one atmosphere where a vaporization temperature of 110 °C gave flux ∼ 7 μmol/min. Auger electron spectroscopy confirmed that addition of H{sub 2}O to the carrier gas stream mitigated F contamination giving nearly 1:1 metal:oxide stoichiometries for both ZnO and AZO with little precursor-derived C contamination. ZnO and AZO thin film resistivities ranged from 14 to 28 Ω·cm for the former and 1.1 to 2.7 Ω·cm for the latter. - Highlights: • A second generation precursor was utilized for atmospheric pressure film growth. • Addition of water vapor to the carrier gas stream led to a marked reduction of ZnF{sub 2}. • Carbonaceous contamination from the precursor was minimal.

  18. Laser sintering of magnesia with nanoparticles of iron oxide and aluminum oxide

    International Nuclear Information System (INIS)

    Highlights: • Laser sintered MgO pellets with nanoparticles of Al2O3 and Fe2O3. • Characterized these pellets by XRD, SEM and XPS. • Spinel formations were observed in both cases. • Changes in morphology and structure were analyzed. - Abstract: Nanoparticles of iron oxide (Fe2O3, 20–40 nm) and aluminum oxide (Al2O3, 50 nm) were mixed in different concentrations (3, 5 and 7 wt%) in a magnesium oxide (MgO) matrix. The mixture pellet was irradiated with 532 nm output from a Q-switched Nd:YAG laser using different laser fluence and translation speed for sintering. The refractory samples obtained were analyzed using X-ray diffraction technique, scanning electron microscopy and X-ray photoelectron spectroscopy. The results showed that the samples irradiated at translation speed of 110 μm/s and energy fluence of 1.7 J/cm2 with a concentration of 5 and 7 wt% of Fe2O3 presented the MgFe2O4 spinel-type phase. With the addition of Al2O3 nanoparticles, at a translation speed of 110 μm/s and energy fluence of 1.7 J/cm2, there were the formations of MgAl2O4 spinel phase. The changes in morphologies and microstructure due to laser irradiation were analyzed

  19. Characterization and Tribological Properties of Hard Anodized and Micro Arc Oxidized 5754 Quality Aluminum Alloy

    Directory of Open Access Journals (Sweden)

    M. Ovundur

    2015-03-01

    Full Text Available This study was initiated to compare the tribological performances of a 5754 quality aluminum alloy after hard anodic oxidation and micro arc oxidation processes. The structural analyses of the coatings were performed using XRD and SEM techniques. The hardness of the coatings was determined using a Vickers micro-indentation tester. Tribological performances of the hard anodized and micro arc oxidized samples were compared on a reciprocating wear tester under dry sliding conditions. The dry sliding wear tests showed that the wear resistance of the oxide coating generated by micro arc oxidation is remarkably higher than that of the hard anodized alloy.

  20. Porous Spherical Cellulose Composites Coated by Aluminum (Ⅲ) Oxide and Silicone: Preparation,Characterization and Adsorption Behavior

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Porous spherical cellulose composite (PSCA) coated by aluminum (Ⅲ) oxide was prepared andmodified by organosilicone. SEM images of the surface morphology of the bead cellulose shows that it hasspherical shape and abundant porous structure on its surface. The mapping images of aluminum and silicon ofthe composite (PSCAS) present aluminum( Ⅲ ) oxide and silicone are uniformly dispersed on the surface. Theadsorption behavior of PSCAS toward metal ions was determined.

  1. Cerium oxide as conversion coating for the corrosion protection of aluminum

    Directory of Open Access Journals (Sweden)

    JELENA GULICOVSKI

    2013-11-01

    Full Text Available CeO2 coatings were formed on the aluminum after Al surface preparation, by dripping the ceria sol, previously prepared by forced hydrolysis of Ce(NO34. The anticorrosive properties of ceria coatings were investigated by the electrochemical impedance spectroscopy (EIS during the exposure to 0.03 % NaCl. The morphology of the coatings was examined by the scanning electron microscopy (SEM. EIS data indicated considerably larger corrosion resistance of CeO2-coated aluminum than for bare Al. The corrosion processes on Al below CeO2 coating are subjected to more pronounced diffusion limitations in comparison to the processes below passive aluminum oxide film, as the consequence of the formation of highly compact protective coating. The results show that the deposition of ceria coatings is an effective way to improve corrosion resistance for aluminum.

  2. Mueller Matrix of Specular Reflection Using an Aluminum Grating Surface with Oxide Nanofilm.

    Science.gov (United States)

    Qiu, Jun; Ran, Dongfang; Liu, Linhua; Hsu, Pei-Feng

    2016-06-01

    The accurate nondestructive and real-time determination of the critical dimensions of oxide nanofilms on periodic nanostructures has potential applications in nanofabrication techniques. Mueller ellipsometry is fast, accurate, nondestructive, and can be used in the ambient air. This study used the elements of a Mueller matrix of specular reflection, which is based on a Mueller ellipsometry method, to evaluate the thickness of an oxide nanofilm on an aluminum grating surface. By using non-traditional rigorous coupled-wave analysis (RCWA), we decomposed the Mueller matrix to obtain the relationship between the evaluated polarization properties of reflected light and the dimensions of oxide nanofilms on aluminum grating surfaces. We also quantitatively analyzed the Mueller matrix elements' variation due to the thicknesses of top, sidewall, and bottom oxides. We consider these oxide films are naturally formed and of nonuniform thickness on grating structures. The results show that the elements of Mueller matrix shift with the increasing of the uniform thickness of oxide at a fixed wavelength. Moreover, as oxide nanofilms on grating structures are nonuniform, the impact of the thickness of side wall oxide on the Mueller matrix elements is more obvious than that of top and bottom oxides at the relative larger incidence wavelength range. The finding of this work may facilitate the nondestructive and real-time measurement of the thickness of oxide nanofilms on metal gratings where the metal is easily oxidized. PMID:27129364

  3. Nanopatterning of Crystalline Silicon Using Anodized Aluminum Oxide Templates for Photovoltaics

    Science.gov (United States)

    Chao, Tsu-An

    A novel thin film anodized aluminum oxide templating process was developed and applied to make nanopatterns on crystalline silicon to enhance the optical properties of silicon. The thin film anodized aluminum oxide was created to improve the conventional thick aluminum templating method with the aim for potential large scale fabrication. A unique two-step anodizing method was introduced to create high quality nanopatterns and it was demonstrated that this process is superior over the original one-step approach. Optical characterization of the nanopatterned silicon showed up to 10% reduction in reflection in the short wavelength range. Scanning electron microscopy was also used to analyze the nanopatterned surface structure and it was found that interpore spacing and pore density can be tuned by changing the anodizing potential.

  4. Enhancement of oxidation resistance of NBD 200 silicon nitride ceramics by aluminum implantation

    Science.gov (United States)

    Mukundhan, Priya

    Silicon nitride (Si3N4) ceramics are leading candidates for high temperature structural applications. They have already demonstrated functional capabilities well beyond the limits of conventional metals and alloys in advanced diesel and turbine engines. However, the practical exploitation of these benefits is limited by their oxidation and associated degradation processes in chemically aggressive environments. Additives and impurities in Si3N4 segregate to the surface of Si3N 4 and accelerate its high temperature oxidation process. This study aims to investigate the oxidation behavior of Norton NBD 200 silicon nitride (hot isostatically pressed with ˜1 wt.% MgO) and its modification by aluminum surface alloying. NBD 200 samples tribochemically polished to a mirror finish (10 nm) were implanted with 5, 10, 20 and 30 at.% aluminum at multienergies and multi-doses to achieve a uniform implant depth distribution to 200 nm. Unimplanted and aluminum-implanted samples were oxidized at 800°--1100°C in 1 atm O2 for 0.5--10 hours. Oxidation kinetics was determined using profilometry in conjunction with etch patterning. The morphological, structural and chemical characteristics of the oxide were characterized by various analytical techniques such as scanning electron microscope and energy dispersive x-ray analysis, secondary ion mass spectrometry and x-ray photoelectron spectroscopy. Oxidation of NBD 200 follows parabolic kinetics in the temperature range investigated and the process is diffusion-controlled. The oxide layers are enriched with sodium and magnesium from the bulk of the Si3N 4. The much higher oxidation rate for NBD 200 silicon nitride than for other silicon nitride ceramics with a similar amount of MgO is attributed to the presence of sodium. The rate-controlling mechanism is the outward diffusion of Mg2+ from the grain boundaries to the oxide scale. Aluminum implantation alleviates the detrimental effects of Na+ and Mg2+; not only is the rate of oxidation

  5. Plasma-enhanced Chemical Vapor Deposition of Aluminum Oxide Using Ultrashort Precursor Injection Pulses

    NARCIS (Netherlands)

    Dingemans, G.; M. C. M. van de Sanden,; Kessels, W. M. M.

    2012-01-01

    An alternative plasma-enhanced chemical vapor deposition (PECVD) method is developed and applied for the deposition of high-quality aluminum oxide (AlOx) films. The PECVD method combines a continuous plasma with ultrashort precursor injection pulses. We demonstrate that the modulation of the precurs

  6. Propagation of nonequilibrium phonons in aluminum-oxide ceramics fabricated by cold isostatic pressing

    International Nuclear Information System (INIS)

    Propagation of slightly nonequilibrium phonons in aluminum-oxide ceramics fabricated by cold isostatic pressing has been studied. Assuming that phonon propagation in ceramic grains is ballistic, we have analyzed characteristics of the phonon scattering and drawn some conclusions about the nature of grain boundaries

  7. Fabrication, structural characterization and sensing properties of polydiacetylene nanofibers templated from anodized aluminum oxide

    Science.gov (United States)

    Polydiacetylene (PDA), a unique conjugated polymer, has shown its potential in the application of chem/bio-sensors and optoelectronics. In this work, we first infiltrated PDA monomer (10, 12-pentacosadiynoic acid, PCDA) melted into the anodized aluminum oxide template, and then illuminated the infil...

  8. Standard specification for nuclear-grade aluminum oxide-boron carbide composite pellets

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2005-01-01

    1.1 This specification applies to pellets composed of mixtures of aluminum oxide and boron carbide that may be ultimately used in a reactor core, for example, in neutron absorber rods. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

  9. In-situ measurement of the electrical conductivity of aluminum oxide in HFIR

    Energy Technology Data Exchange (ETDEWEB)

    Zinkle, S.J.; White, D.P.; Snead, L.L. [Oak Ridge National Lab., TN (United States)] [and others

    1996-10-01

    A collaborative DOE/Monbusho irradiation experiment has been completed which measured the in-situ electrical resistivity of 12 different grades of aluminum oxide during HFIR neutron irradiation at 450{degrees}C. No evidence for bulk RIED was observed following irradiation to a maximum dose of 3 dpa with an applied dc electric field of 200 V/mm.

  10. Oxidation of silicon implanted with high-dose aluminum

    International Nuclear Information System (INIS)

    Si (100) wafers were implanted with Al at 500 C to high doses at multi-energies and were oxidized in 1 atm flowing oxygen at 1,000--1,200 C. The morphology, structure, and oxidation behavior of the implanted and oxidized Si were studied using optical microscopy, atomic force microscopy, and cross-sectional transmission electron microscopy in conjunction with selected area electron diffraction and energy dispersive x-ray analysis. Large Al precipitates were formed and embedded near the surface region of the implanted Si. The oxidation rate of the Al-implanted Si wafers was lower than that of virgin Si. The unique morphology of the implanted Si results from rapid Al diffusion and segregation promoted by hot implantation. The reduction of the oxidation rate of Si by Al implantation is attributed to the preferential oxidation of Al and formation of a continuous diffusion barrier of Al2O3

  11. Dissolution of Oxide Films on Aluminum in Near Neutral Solutions

    Energy Technology Data Exchange (ETDEWEB)

    Isaacs, Hugh S.; Xu, Feng; Jeffcoate, Carrol S.

    1999-10-17

    Simple linear potentiodynamic cycling measurements have been made on abraded pure Al in borate, chromate, phosphate, sulfate and nitrate solutions. In borate and chromate solutions the currents continued to decrease with each subsequent cycle. In phosphate dissolution of the oxide takes place producing repetitive repeat curves. The current variations in borate and chromate were simulated using a high field conduction oxide growth model. Including oxide dissolution in the model simulated the phosphate behavior. Results in sulfate and nitrate solutions were more complex. The behavior in the sulfate solution was attributed to effects of sulfate the oxide/solution interface.

  12. Laser sintering of magnesia with nanoparticles of iron oxide and aluminum oxide

    Energy Technology Data Exchange (ETDEWEB)

    García, L.V.; Mendivil, M.I.; Roy, T.K. Das; Castillo, G.A. [Facultad de Ingenieria Mecanica y Electrica, Universidad Autonoma de Nuevo Leon, Av. Pedro de Alba s/n, Cd. Universitaria, San Nicolas de los Garza, Nuevo Leon 66451 (Mexico); Shaji, S., E-mail: sshajis@yahoo.com [Facultad de Ingenieria Mecanica y Electrica, Universidad Autonoma de Nuevo Leon, Av. Pedro de Alba s/n, Cd. Universitaria, San Nicolas de los Garza, Nuevo Leon 66451 (Mexico); CIIDIT, Universidad Autonoma de Nuevo Leon, Apodaca, Nuevo Leon (Mexico)

    2015-05-01

    Highlights: • Laser sintered MgO pellets with nanoparticles of Al{sub 2}O{sub 3} and Fe{sub 2}O{sub 3}. • Characterized these pellets by XRD, SEM and XPS. • Spinel formations were observed in both cases. • Changes in morphology and structure were analyzed. - Abstract: Nanoparticles of iron oxide (Fe{sub 2}O{sub 3}, 20–40 nm) and aluminum oxide (Al{sub 2}O{sub 3}, 50 nm) were mixed in different concentrations (3, 5 and 7 wt%) in a magnesium oxide (MgO) matrix. The mixture pellet was irradiated with 532 nm output from a Q-switched Nd:YAG laser using different laser fluence and translation speed for sintering. The refractory samples obtained were analyzed using X-ray diffraction technique, scanning electron microscopy and X-ray photoelectron spectroscopy. The results showed that the samples irradiated at translation speed of 110 μm/s and energy fluence of 1.7 J/cm{sup 2} with a concentration of 5 and 7 wt% of Fe{sub 2}O{sub 3} presented the MgFe{sub 2}O{sub 4} spinel-type phase. With the addition of Al{sub 2}O{sub 3} nanoparticles, at a translation speed of 110 μm/s and energy fluence of 1.7 J/cm{sup 2}, there were the formations of MgAl{sub 2}O{sub 4} spinel phase. The changes in morphologies and microstructure due to laser irradiation were analyzed.

  13. Modelling the growth process of porous aluminum oxide film during anodization

    Science.gov (United States)

    Aryslanova, E. M.; Alfimov, A. V.; Chivilikhin, S. A.

    2015-11-01

    Currently it has become important for the development of metamaterials and nanotechnology to obtain regular self-assembled structures. One such structure is porous anodic alumina film that consists of hexagonally packed cylindrical pores. In this work we consider the anodization process, our model takes into account the influence of layers of aluminum and electrolyte on the rate of growth of aluminum oxide, as well as the effect of surface diffusion. In present work we consider those effects. And as a result of our model we obtain the minimum distance between centers of alumina pores in the beginning of anodizing process.

  14. Combined flame and electrodeposition synthesis of energetic coaxial tungsten-oxide/aluminum nanowire arrays.

    Science.gov (United States)

    Dong, Zhizhong; Al-Sharab, Jafar F; Kear, Bernard H; Tse, Stephen D

    2013-09-11

    A nanostructured thermite composite comprising an array of tungsten-oxide (WO2.9) nanowires (diameters of 20-50 nm and lengths of >10 μm) coated with single-crystal aluminum (thickness of ~16 nm) has been fabricated. The method involves combined flame synthesis of tungsten-oxide nanowires and ionic-liquid electrodeposition of aluminum. The geometry not only presents an avenue to tailor heat-release characteristics due to anisotropic arrangement of fuel and oxidizer but also eliminates or minimizes the presence of an interfacial Al2O3 passivation layer. Upon ignition, the energetic nanocomposite exhibits strong exothermicity, thereby being useful for fundamental study of aluminothermic reactions as well as enhancing combustion characteristics. PMID:23899165

  15. Luminescence properties of oxide films formed by anodization of aluminum in 12-tungstophosphoric acid

    International Nuclear Information System (INIS)

    In this paper, we have investigated luminescence properties of oxide films formed by anodization of aluminum in 12-tungstophosphoric acid. For the first time we have measured weak luminescence during anodization of aluminum in this electrolyte (so-called galvanoluminescence GL) and showed that there are wide GL bands in the visible region of the spectrum and observed two dominant spectral peaks. The first one is at about 425 nm, and the second one shifts with anodization voltage. As the anodization voltage approaches the breakdown voltage, a large number of sparks appear superimposed on the anodic GL. Several intensive band peaks were observed under breakdown caused by electron transitions in W, P, Al, O, H atoms. Furthermore, photoluminescence (PL) of anodic oxide films and anodic-spark formed oxide coatings were performed. In both cases wide PL bands in the range from 320 nm to 600 nm were observed.

  16. Investigation of sub-nm ALD aluminum oxide films by plasma assisted etch-through

    International Nuclear Information System (INIS)

    A new technique, called 'plasma defect etching' (PDE), is proposed for studying the continuity of ultra-thin layers. The PDE technique utilizes the extremely high selectivity in the deep reactive ion etching (DRIE) process, thus achieving visualization of the defects in the layer, because etching of substrate happens only through voids and microholes of the layer. The etch profile generally reproduces the non-continuous structure of the layer. This PDE technique was applied for the investigation of thin, sub-nm aluminum oxide films grown on silicon wafers by atomic layer deposition (ALD) technique. Silicon substrate was etched by SF6 at cryogenic temperatures in an inductively coupled plasma (ICP) reactor, exploiting the extremely high ratio of silicon/aluminum oxide etch rates in fluorine plasmas. The surface morphology was characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The PDE method shows that in the case of water as an oxidation precursor, separate islands of aluminum oxide form during the five first ALD cycles. On the other hand, the use of ozone precursor helps to oxidize silicon surface and facilitates growth of a uniform layer

  17. Aluminum cladding oxidation of prefilmed in-pile fueled experiments

    Science.gov (United States)

    Marcum, W. R.; Wachs, D. M.; Robinson, A. B.; Lillo, M. A.

    2016-04-01

    A series of fueled irradiation experiments were recently completed within the Advanced Test Reactor Full size plate In center flux trap Position (AFIP) and Gas Test Loop (GTL) campaigns. The conduct of the AFIP experiments supports ongoing efforts within the global threat reduction initiative (GTRI) to qualify a new ultra-high loading density low enriched uranium-molybdenum fuel. This study details the characterization of oxide growth on the fueled AFIP experiments and cross-correlates the empirically measured oxide thickness values to existing oxide growth correlations and convective heat transfer correlations that have traditionally been utilized for such an application. This study adds new and valuable empirical data to the scientific community with respect to oxide growth measurements of highly irradiated experiments, of which there is presently very limited data. Additionally, the predicted oxide thickness values are reconstructed to produce an oxide thickness distribution across the length of each fueled experiment (a new application and presentation of information that has not previously been obtainable in open literature); the predicted distributions are compared against experimental data and in general agree well with the exception of select outliers.

  18. The thickness of native oxides on aluminum alloys and single crystals

    International Nuclear Information System (INIS)

    Highlights: • We have determined the native oxide film thickness on several Al samples. • The results obtained from XRR and XPS show excellent agreement. • The results obtained from EIS show consistently thinner oxide films. • The oxides on the alloys are thicker than the oxides on the single crystals. - Abstract: We present results from measurements of the native oxide film thickness on four different industrial aluminum alloys and three different aluminum single crystals. The thicknesses were determined using X-ray reflectivity, X-ray photoelectron spectroscopy, and electrochemical impedance spectroscopy. In addition, atomic force microscopy was used for micro-structural studies of the oxide surfaces. The reflectivity measurements were performed in ultra-high vacuum, vacuum, ambient, nitrogen and liquid water conditions. The results obtained using X-ray reflectivity and X-ray photoelectron spectroscopy demonstrate good agreement. However, the oxide thicknesses determined from the electrochemical impedance spectroscopy show a larger discrepancy from the above two methods. In the present contribution the reasons for this discrepancy are discussed. We also address the effect of the substrate type and the presence of water on the resultant oxide thickness

  19. The thickness of native oxides on aluminum alloys and single crystals

    Energy Technology Data Exchange (ETDEWEB)

    Evertsson, J., E-mail: jonas.evertsson@sljus.lu.se [Division of Synchrotron Radiation Research, Lund University, Box 118, 221 00 Lund (Sweden); Bertram, F. [Division of Synchrotron Radiation Research, Lund University, Box 118, 221 00 Lund (Sweden); Zhang, F. [KTH Royal Institute of Technology, Department of Chemistry, Division of Surface and Corrosion Science, Drottning Kristinas Vg 51, 100 44 Stockholm (Sweden); Rullik, L.; Merte, L.R.; Shipilin, M. [Division of Synchrotron Radiation Research, Lund University, Box 118, 221 00 Lund (Sweden); Soldemo, M.; Ahmadi, S. [KTH Royal Institute of Technology, ICT, Material Physics, 16440 Kista (Sweden); Vinogradov, N.; Carlà, F. [ESRF, B.P. 220, 38043 Grenoble (France); Weissenrieder, J.; Göthelid, M. [KTH Royal Institute of Technology, ICT, Material Physics, 16440 Kista (Sweden); Pan, J. [KTH Royal Institute of Technology, Department of Chemistry, Division of Surface and Corrosion Science, Drottning Kristinas Vg 51, 100 44 Stockholm (Sweden); Mikkelsen, A. [Division of Synchrotron Radiation Research, Lund University, Box 118, 221 00 Lund (Sweden); Nilsson, J.-O. [Sapa Technology, Kanalgatan 1, 612 31 Finspång (Sweden); Lundgren, E. [Division of Synchrotron Radiation Research, Lund University, Box 118, 221 00 Lund (Sweden)

    2015-09-15

    Highlights: • We have determined the native oxide film thickness on several Al samples. • The results obtained from XRR and XPS show excellent agreement. • The results obtained from EIS show consistently thinner oxide films. • The oxides on the alloys are thicker than the oxides on the single crystals. - Abstract: We present results from measurements of the native oxide film thickness on four different industrial aluminum alloys and three different aluminum single crystals. The thicknesses were determined using X-ray reflectivity, X-ray photoelectron spectroscopy, and electrochemical impedance spectroscopy. In addition, atomic force microscopy was used for micro-structural studies of the oxide surfaces. The reflectivity measurements were performed in ultra-high vacuum, vacuum, ambient, nitrogen and liquid water conditions. The results obtained using X-ray reflectivity and X-ray photoelectron spectroscopy demonstrate good agreement. However, the oxide thicknesses determined from the electrochemical impedance spectroscopy show a larger discrepancy from the above two methods. In the present contribution the reasons for this discrepancy are discussed. We also address the effect of the substrate type and the presence of water on the resultant oxide thickness.

  20. Electrical properties of aluminum-doped zinc oxide (AZO) nanoparticles synthesized by chemical vapor synthesis

    International Nuclear Information System (INIS)

    Aluminum-doped zinc oxide nanoparticles have been prepared by chemical vapor synthesis, which facilitates the incorporation of a higher percentage of dopant atoms, far above the thermodynamic solubility limit of aluminum. The electrical properties of aluminum-doped and undoped zinc oxide nanoparticles were investigated by impedance spectroscopy. The impedance is measured under hydrogen and synthetic air between 323 and 673 K. The measurements under hydrogen as well as under synthetic air show transport properties depending on temperature and doping level. Under hydrogen atmosphere, a decreasing conductivity with increasing dopant content is observed, which can be explained by enhanced scattering processes due to an increasing disorder in the nanocrystalline material. The temperature coefficient for the doped samples switches from positive temperature coefficient behavior to negative temperature coefficient behavior with increasing dopant concentration. In the presence of synthetic air, the conductivity firstly increases with increasing dopant content by six orders of magnitude. The origin of the increasing conductivity is the generation of free charge carriers upon dopant incorporation. It reaches its maximum at a concentration of 7.7% of aluminum, and drops for higher doping levels. In all cases, the conductivity under hydrogen is higher than under synthetic air and can be changed reversibly by changing the atmosphere.

  1. Large pore volume mesoporous aluminum oxide synthesized via nano-assembly

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    A new nano-assembly approach has been proposed for the preparation of macropore volume mesoporous aluminum oxide supports. Secondary nano-assembly and a frame structure mechanism for large pore volume mesoporous supports have been proposed. In a primary nano-assembly supersoluble micelle,aluminum hydroxide nanoparticles were precipitated in situ in surfactants with a volume balance (VB) less than 1,followed by secondary nano-assembly in linear and cylindrical shapes. The secondary nano-assembly of cylindrical aluminum hydroxides was calcined to form nano cylindrical aluminum oxides. For the formation of macropore volume mesoporous supports,we utilized a frame structure mechanism of mesoporous support,in which the exterior surface of the carrier may not be continuous. This macropore volume support has been used for the hydrotreatment of a residual oil catalyst,which possesses the following physical characteristics:pore volume 1.8―2.7 mL·g-1,specific surface area 180―429 m2·g-1,average pore diameter 17―57 nm,average pore diameter more than 10 nm (81%―94%),porosity 87%―93%,and crush strength 7.7―25 N·mm-1.

  2. Modeling of oxidation of aluminum nanoparticles by using Cabrera Mott Model

    Science.gov (United States)

    Ramazanova, Zamart; Zyskin, Maxim; Martirosyan, Karen

    2012-10-01

    Our research focuses on modeling new Nanoenergetic Gas-Generator (NGG) formulations that rapidly release a large amount of gaseous products and generates shock and pressure waves. Nanoenergetic thermite reagents include mixtures of Al and metal oxides such as bismuth trioxide and iodine pentoxide. The research problem is considered a spherically symmetric case and used the Cabrera Mott oxidation model to describe the kinetics of oxide growth on spherical Al nanoparticles for evaluating reaction time which a process of the reaction with oxidizer happens on the outer part of oxide layer of aluminum ions are getting in contact with an oxidizing agent and react. We assumed that a ball of Al of radius 20 to 50 nm is covered by a thin oxide layer 2-4 nm and is surrounded by abundant amount of oxygen stored by oxidizers. The ball is rapidly heated up to ignition temperature to initiate self-sustaining oxidation reaction. As a result highly exothermic reaction is generated. In the oxide layer of excess concentrations of electrons and ions are dependent on the electric field potential with the corresponding of the Gibbs factors and that it conducts to the solution of a nonlinear Poisson equation for the electric field potential in a moving boundary domain. Motion of the boundary is determined by the gradient of a solution on the boundary. We investigated oxidation model numerically, using the COMSOL software utilizing finite element analysis. The computing results demonstrate that oxidation rate increases with the decreasing particle radius.

  3. Standard test methods for chemical, mass spectrometric, and spectrochemical analysis of nuclear-grade aluminum oxide and aluminum oxide-boron carbide composite pellets

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    1994-01-01

    1.1 These test methods cover procedures for the chemical, mass spectrometric, and spectrochemical analysis of nuclear-grade aluminum oxide and aluminum oxide-boron carbide composite pellets to determine compliance with specifications. 1.2 The analytical procedures appear in the following order: Sections Boron by Titrimetry 7 to 13 Separation of Boron for Mass Spectrometry 14 to 19 Isotopic Composition by Mass Spectrometry 20 to 23 Separation of Halides by Pyrohydrolysis 24 to 27 Fluoride by Ion-Selective Electrode 28 to 30 Chloride, Bromide, and Iodide by Amperometric Microtitrimetry 31 to 33 Trace Elements by Emission Spectroscopy 34 to 46 1.3 The values stated in SI units are to be regarded as the standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (F...

  4. Interactions between nitric oxide and plant hormones in aluminum tolerance

    OpenAIRE

    He, Huyi; He, Longfei; Gu, Minghua

    2012-01-01

    Nitric oxide (NO) is involved, together with plant hormones, in the adaptation to Al stress in plants. However, the mechanism by which NO and plant hormones interplay to improve Al tolerance are still unclear. We have recently shown that patterns of plant hormones alteration differ between rye and wheat under Al stress. NO may enhance Al tolerance by regulating hormonal equilibrium in plants, as a regulator of plant hormones signaling. In this paper, some unsolved issues are discussed based o...

  5. Optical Properties of Au Nanoparticles Coated on Surface of Glass or Anodic Aluminum Oxide Template

    Institute of Scientific and Technical Information of China (English)

    FENG Jinyang; WU Can; MA Xiao; ZHANG Hongquan; ZHAO Xiujian

    2012-01-01

    Au nanoparticles coated on the surface of glass (Sample A) or on anodic aluminum oxide template surface (Sample B) were prepared using titanium dioxide sol-gel doped with chloroauric acid and with a reduction process.FE-SEM,UV-Vis spectrum and Fluorescence spectrum tests show that Au nanoparticles have been distributed randomly on the surface of glass,while deposition occurs on the surface of regular hollows for anodic aluminum oxide template.A sharp absorption peak appears at the wavelength of 536 nm for sample B,while there is a red shift,with a broader peak for sample A.A distinct fluorescence emission at the wavelength of 633 nm is detected for sample A,but no noticeable fluorescence emission has been found for Sample B.The results indicate that the microstructure and optical properties of Au nanoparticles can be modulated by different substrate.

  6. Fabrication of polymeric nano-batteries array using anodic aluminum oxide templates.

    Science.gov (United States)

    Zhao, Qiang; Cui, Xiaoli; Chen, Ling; Liu, Ling; Sun, Zhenkun; Jiang, Zhiyu

    2009-02-01

    Rechargeable nano-batteries were fabricated in the array pores of anodic aluminum oxide (AAO) template, combining template method and electrochemical method. The battery consisted of electropolymerized PPy electrode, porous TiO2 separator, and chemically polymerized PAn electrode was fabricated in the array pores of two-step anodizing aluminum oxide (AAO) membrane, based on three-step assembling method. It performs typical electrochemical battery behavior with good charge-discharge ability, and presents a capacity of 25 nAs. AFM results show the hexagonal array of nano-batteries' top side. The nano-battery may be a promising device for the development of Micro-Electro-Mechanical Systems (MEMS), and Nano-Electro-Mechanical Systems (NEMS). PMID:19441424

  7. Aluminum oxide sputtering: a new approach to understanding the sputtering process for binary targets

    International Nuclear Information System (INIS)

    The relative abundances of the products Al, Al2O, and AlO sputtered in 15- and 40-kV Ar+ and 15-kV H+ bombardments of aluminum oxide targets (anodized film, polycrystalline disk, sapphire) are functions of the target material and of the nature, flux, and fluence of the ion beam. This finding suggests that, in collisional sputtering, the material's sensitive parameters are the surface binding energies of the sputtered species. These energies are functions of the surface composition present at the moment of a particular sputtering event and should be identified with the partial molar enthalpy of vaporization of a particular species. The aluminum oxide species--Al, Al2O, AlO, Al2O2, AlO2, Al(O2)2, and AlO3--are characterized by matrix isolation spectroscopy aided by O18 isotopic substitution experiments. 12 figures, 4 tables

  8. Stabilization of aluminum doped zinc oxide nanoparticle suspensions and their application in organic solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Wolf, N., E-mail: nadine.wolf@zae-bayern.de [Bavarian Center for Applied Energy Research (ZAE Bayern), Division: Energy Efficiency, Am Galgenberg 87, 97074 Wuerzburg (Germany); Stubhan, T. [Institute of Materials for Electronics and Energy Technology (I-MEET), Friedrich-Alexander-University of Erlangen-Nuremberg, Martensstraße 7, 91058 Erlangen (Germany); Manara, J.; Dyakonov, V. [Bavarian Center for Applied Energy Research (ZAE Bayern), Division: Energy Efficiency, Am Galgenberg 87, 97074 Wuerzburg (Germany); Brabec, C.J. [Institute of Materials for Electronics and Energy Technology (I-MEET), Friedrich-Alexander-University of Erlangen-Nuremberg, Martensstraße 7, 91058 Erlangen (Germany); Bavarian Center for Applied Energy Research (ZAE Bayern), Division: Renewable Energies, Haberstraße 2a, 91058 Erlangen (Germany)

    2014-08-01

    Aluminum doped zinc oxide (AZO) nanoparticles were redispersed in isopropyl alcohol and stabilized with different stabilizers and mixtures of stabilizers that allow for electronically functional particles. The size of the redispersed nanoparticles was small enough to use these suspensions to build interfacial layers in inverted polymer-fullerene solar cells. The performance of these devices was found to depend on the stabilizer used in the nanoparticle suspension. The best performance was obtained with an AZO interfacial layer built with a 3,6,9-trioxadecanoic acid and polyvinylpyrrolidone stabilized nanoparticle suspension. - Highlights: • Preparation of stable aluminum doped zinc oxide nanoparticle suspensions • Different stabilizers were used to stabilize these nanoparticle suspensions. • The material was used as interfacial layers in inverted polymer solar cells. • The performance of these devices depends on the stabilizer used in the suspension.

  9. Effect of conditions of thermal treatment on the porous structure of an aluminum oxide-containing nanofibrous aerogel

    Science.gov (United States)

    Markova, E. B.; Krasil'nikova, O. K.; Grankina, T. Yu.; Serov, Yu. M.

    2016-08-01

    The effect the conditions of thermal treatment have on a specific surface and the number of primary adsorption centers is studied. The relationship between changing adsorption characteristics and changes in the structure of nanofibrous aluminum oxide is considered.

  10. Radial Combustion Propagation in Iron(III) Oxide/Aluminum Thermite Mixtures

    OpenAIRE

    Durães, Luísa; Campos, José; Portugal, António

    2006-01-01

    The self-sustained thermite reaction between iron oxide (Fe2O3) and aluminum is a classical source of energy. In this work the radial combustion propagation on thin circular samples of stoichiometric and over aluminized Fe2O3/Al thermite mixtures is studied. The radial geometry allows an easy detection of sample heterogeneities and the observation of the combustion behavior in their vicinity. The influence of factors like reactant mixtures stoichiometry, samples green density and system geome...

  11. Commensurate vortex pinning in Nb films patterned onto anodized aluminum oxide

    International Nuclear Information System (INIS)

    Anodic aluminum oxide templates containing extended arrays of holes with ∼30-nm diameter and approximately 128-nm spacing were sputter-coated with Nb. We find pronounced matching effects in the transport and magnetization measurements beyond 4 kOe. In addition, we observe Little-Parks oscillations of the superconducting critical temperature. We compare the flux pinning in the patterned samples to unpatterned reference samples and find a significant enhancement of the critical current

  12. Computer simulation of the photoluminescence of nanostructured aluminum oxide excited with pulsed synchrotron radiation

    OpenAIRE

    Kortov, V. S.; Spiridonova, T. V.; Zvonarev, S. V.

    2013-01-01

    An algorithm and a program are developed to calculate the photoluminescence (PL) parameters for bulk single-crystal and nanoscale dielectrics excited with pulsed synchrotron radiation. The luminescence spectra of F and F+centers and the PL decay kinetics in single-crystal and nanoscale aluminum-oxide samples containing oxygen anion vacancies are calculated for various nanoparticle sizes. It is shown that a noticeable broadening of the bands and a decrease in the afterglow time is observed for...

  13. Characterization of Lipid Bilayer Formation in Aligned Nanoporous Aluminum Oxide Nanotube Arrays

    OpenAIRE

    Karp, Ethan S.; Newstadt, Justin P.; Chu, Shidong; Lorigan, Gary A.

    2007-01-01

    Aligning lipid bilayers in nanoporous anodized aluminum oxide (AAO) is a new method to help study membrane proteins by electron paramagnetic resonance (EPR) and solid-state nuclear magnetic resonance (NMR) spectroscopic methods. The ability to maintain hydration, sample stability, and compartmentalization over long periods of time, and to easily change solvent composition are major advantages of this new method. To date, 1,2-dimyristoyl-sn-glycero-3-phosphatidylcholine (DMPC) has been the onl...

  14. Growth behavior of anodic oxide formed by aluminum anodizing in glutaric and its derivative acid electrolytes

    Science.gov (United States)

    Nakajima, Daiki; Kikuchi, Tatsuya; Natsui, Shungo; Suzuki, Ryosuke O.

    2014-12-01

    The growth behavior of anodic oxide films formed via anodizing in glutaric and its derivative acid solutions was investigated based on the acid dissociation constants of electrolytes. High-purity aluminum foils were anodized in glutaric, ketoglutaric, and acetonedicarboxylic acid solutions under various electrochemical conditions. A thin barrier anodic oxide film grew uniformly on the aluminum substrate by glutaric acid anodizing, and further anodizing caused the film to breakdown due to a high electric field. In contrast, an anodic porous alumina film with a submicrometer-scale cell diameter was successfully formed by ketoglutaric acid anodizing at 293 K. However, the increase and decrease in the temperature of the ketoglutaric acid resulted in non-uniform oxide growth and localized pitting corrosion of the aluminum substrate. An anodic porous alumina film could also be fabricated by acetonedicarboxylic acid anodizing due to the relatively low dissociation constants associated with the acid. Acid dissociation constants are an important factor for the fabrication of anodic porous alumina films.

  15. Preparation and analysis of anodic aluminum oxide films with continuously tunable interpore distances

    Science.gov (United States)

    Qin, Xiufang; Zhang, Jinqiong; Meng, Xiaojuan; Deng, Chenhua; Zhang, Lifang; Ding, Guqiao; Zeng, Hao; Xu, Xiaohong

    2015-02-01

    Nanoporous anodic aluminum oxides are often used as templates for preparation of nanostructures such as nanodot, nanowire and nanotube arrays. The interpore distance of anodic aluminum oxide is the most important parameter in controlling the periodicity of these nanostructures. Herein we demonstrate a simple and yet powerful method to fabricate ordered anodic aluminum oxides with continuously tunable interpore distances. By using mixed solution of citric and oxalic acids with different molar ratio, the range of anodizing voltages within which self-ordered films can be formed were extended to between 40 and 300 V, resulting in the interpore distances change from 100 to 750 nm. Our work realized very broad range of interpore distances in a continuously tunable fashion and the experiment processes are easily controllable and reproducible. The dependence of the interpore distances on acid ratios in mixed solutions was discussed through analysis of anodizing current and it was found that the effective dissociation constant of the mixed acids is of great importance. The interpore distances achieved are comparable to wavelengths ranging from UV to near IR, and may have potential applications in optical meta-materials for photovoltaics and optical sensing.

  16. Anodic Aluminum Oxide Templates for Nano wires Array Fabrication

    International Nuclear Information System (INIS)

    This paper reports on the process developed to fabricate anodic aluminium oxide (AAO) templates suitable for the fabrication of nano wire arrays. Anodization process has been used to fabricate the AAO templates with pore diameters ranging from 15 nm to 30 nm. Electrodeposition of parallel arrays of high aspect ratio nickel nano wires were demonstrated using these fabricated AAO templates. The nano wires produced were characterized using X-ray diffraction (XRD) and scanning electron microscopy (SEM). It was found that the orientations of the electrodeposited nickel nano wires were governed by the deposition current and electrolyte conditions. (author)

  17. Elaboration of aluminum oxide-based graphite containing castables

    Science.gov (United States)

    Zhou, Ningsheng

    The aim of this work was set to develop effective and practicable new methods to incorporate natural flake graphite (FG) into the Al2O 3 based castables for iron and steel making applications. Three approaches, viz. micro-pelletized graphite (PG), crushed briquette of Al2O3-graphite (BAG) and TiO2 coated graphite (CFG), have been developed to insert flake graphite into Al2O 3 rich Al2O3-SiC based and Al2O 3-MgO based castables. These approaches were put into effect as countermeasures against the problems caused by FG in order: (1) to agglomerate the FG powders so as to decrease the specific surface area; (2) to diminish the density difference by using crushed carbon bonded compact of oxide-FG mixture; (3) to modify the surface of the flake graphite by forming hydrophilic coating; (4) to control the dispersion state of the graphite in the castable to maintain enough bonding strength; and (5) to use appropriate antioxidants to inhibit the oxidation of FG. The whole work was divided into two stages. In stage one, Al2O 3-SiC-C castables were dealt with to compare 4 modes of inserting graphite, i.e., by PG, BAG, CFG and FG. Overall properties were measured, all in correlation with graphite amount and incorporating mode. In stage two, efforts were made to reduce water demand in the Al2O3-MgO castables system. For this purpose, the matrix portion of the castable mixes was extracted and a coaxial double cylinder viscometer was adopted to investigate rheological characteristics of the matrix slurries vs. 4 kinds of deflocculants, through which the best deflocculant and its appropriate amount were found. Efforts were then made to add up to 30% MgO into the castables, using a limited amount of powders (<0.3 mm), the rest being increased in size gradually up to the top size of 4.76 mm. Into the optimized Al2O3-MgO castables graphite was incorporated by PG and BAG, and 4 kinds of antioxidants, Si, SiC, B4C and ZrB2, were added respectively or in combination. Overall properties

  18. Peculiarities of luminescence of nanostructured aluminum oxide with chromium impurity

    International Nuclear Information System (INIS)

    Comparative study of Cr3+ ions photo-, X-ray- and cathodoluminescence in R-lines region in monocrystal and nanostructural aluminium oxide samples with different phase composition is conducted. Peculiarities of chromium impurity inclusion into Al2O3 nanocrystal lattices at high-temperature thermal treatment of Al2O3 and Cr2O3 nanopowders mixture are revealed. It is shown that aluminium oxides nanostructuring can result in formation of complicated aggregate complexes which include anion vacancies and impurity cations. It is marked that the most likely cause of quenching of R-lines luminescence and their broadening at Al2O3 crystal symmetry decrease in α → θ → δ → γ series is anion sublattice disordering while action of crystal field is responsible for levels displacement. It is established that thermal treatment at 1200 deg C doesn't result in complete transformation of nanostructural Al2O3 into α-form as it takes place in macro state

  19. Effect of aluminum oxide on the compressive strength of pellets

    Institute of Scientific and Technical Information of China (English)

    Jian-liang Zhang; Zhen-yang Wang; Xiang-dong Xing; Zheng-jian Liu

    2014-01-01

    Analytical-reagent-grade Al2O3 was added to magnetite ore during the process of pelletizing, and the methods of mercury intru-sion, scanning electron microscopy, and image processing were used to investigate the effect of Al2O3 on the compressive strength of the pellets. The results showed that, as the Al2O3 content increased, the compressive strength of the pellets increased slightly and then decreased gradually. When a small amount of Al2O3 was added to the pellets, the Al2O3 combined with fayalite (2FeO·SiO2) and the aluminosilicate (2FeO·2Al2O3·5SiO2) was generated, which releases some iron oxide and reduces the inhibition of fayalite to the solid phase of consolidation. When Al2O3 increased sequentially, high melting point of Al2O3 particles hinder the oxidation of Fe3O4 and the recrystallization of Fe2O3, making the internal porosity of the pellets increase, which leads to the decrease in compressive strength of the pellets.

  20. Systematic review of potential health risks posed by pharmaceutical, occupational and consumer exposures to metallic and nanoscale aluminum, aluminum oxides, aluminum hydroxide and its soluble salts

    Science.gov (United States)

    Willhite, Calvin C.; Karyakina, Nataliya A.; Yokel, Robert A.; Yenugadhati, Nagarajkumar; Wisniewski, Thomas M.; Arnold, Ian M. F.; Momoli, Franco; Krewski, Daniel

    2016-01-01

    Aluminum (Al) is a ubiquitous substance encountered both naturally (as the third most abundant element) and intentionally (used in water, foods, pharmaceuticals, and vaccines); it is also present in ambient and occupational airborne particulates. Existing data underscore the importance of Al physical and chemical forms in relation to its uptake, accumulation, and systemic bioavailability. The present review represents a systematic examination of the peer-reviewed literature on the adverse health effects of Al materials published since a previous critical evaluation compiled by Krewski et al. (2007). Challenges encountered in carrying out the present review reflected the experimental use of different physical and chemical Al forms, different routes of administration, and different target organs in relation to the magnitude, frequency, and duration of exposure. Wide variations in diet can result in Al intakes that are often higher than the World Health Organization provisional tolerable weekly intake (PTWI), which is based on studies with Al citrate. Comparing daily dietary Al exposures on the basis of “total Al” assumes that gastrointestinal bioavailability for all dietary Al forms is equivalent to that for Al citrate, an approach that requires validation. Current occupational exposure limits (OELs) for identical Al substances vary as much as 15-fold. The toxicity of different Al forms depends in large measure on their physical behavior and relative solubility in water. The toxicity of soluble Al forms depends upon the delivered dose of Al+3 to target tissues. Trivalent Al reacts with water to produce bidentate superoxide coordination spheres [Al(O2)(H2O4)+2 and Al(H2O)6+3] that after complexation with O2•−, generate Al superoxides [Al(O2•)](H2O5)]+2. Semireduced AlO2• radicals deplete mitochondrial Fe and promote generation of H2O2, O2•− and OH•. Thus, it is the Al+3-induced formation of oxygen radicals that accounts for the oxidative damage that

  1. Sorption of phenanthrene by dissolved organic matter and its complex with aluminum oxide nanoparticles

    International Nuclear Information System (INIS)

    Intent of this study was to explore the potential application of polymerin, the polymeric, dissolved organic matter fraction from olive oil wastewaters, in technologies aimed at remediating hydrophobic organic compounds (HOCs) point-source pollution. Phenanthrene binding with polymerin was investigated. Moreover, the effect of addition of micro and nanoscale aluminum oxides (Al2O3) was studied, as well as sorption of polymerin on the oxides. Phenanthrene binding capacity by polymerin was notably higher than the sorption capacities for both types of Al2O3 particles. Polymerin sorption on nanoparticles was nearly 100 times higher than microparticles. In a three-phase system, using microparticles, higher phenanthrene sorption was found by adding into water polymerin, oxides and phenanthrene simultaneously. In contrast, using nanoparticles, a considerable enhancement of phenanthrene sorption was shown by adding phenanthrene to a pre-formed and dried polymerin-oxide complex. These findings support the application of polymerin, especially associated with Al2O3 nanoparticles, in remediation of water contaminated with HOCs. This work highlights the significant role of nanoparticles. - Size of aluminum oxides significantly affects sorption of polymerin and phenanthrene

  2. Reaction behavior between the oxide film of LY12 aluminum alloy and the flux

    Institute of Scientific and Technical Information of China (English)

    薛松柏; 董健; 吕晓春; 顾文华

    2004-01-01

    In this paper, the brazing mechanism of LY12 aluminum alloy at middle range temperature was presented. The CsF-AlF3 non-corrosive flux was utilized to remove the complex oxide film on the surface of LY12 aluminum alloy. The results revealed that the oxide film was removed by the improved CsF-AlF3 flux accompanied with the occurrence of reaction as well as dissolution and the compounds CsF played an important role to remove the oxide film. Actually, the high activity of flux, say, the ability to remove the oxide film, was due to the presence of the compounds, such as NH4F,NH4AlF4 and composite molten salt. The production of HF was the key issue to accelerate the reaction and enhance to eliminate the oxide film by dissolution. It was found that the rare earth element La at small percentage was not enriched at the interface. Moreover, the rare earth fluoride enhanced the dissolution behavior.

  3. Application of diffusion barriers to the refractory fibers of tungsten, columbium, carbon and aluminum oxide

    Science.gov (United States)

    Douglas, F. C.; Paradis, E. L.; Veltri, R. D.

    1973-01-01

    A radio frequency powered ion-plating system was used to plate protective layers of refractory oxides and carbide onto high strength fiber substrates. Subsequent overplating of these combinations with nickel and titanium was made to determine the effectiveness of such barrier layers in preventing diffusion of the overcoat metal into the fibers with consequent loss of fiber strength. Four substrates, five coatings, and two metal matrix materials were employed for a total of forty material combinations. The substrates were tungsten, niobium, NASA-Hough carbon, and Tyco sapphire. The diffusion-barrier coatings were aluminum oxide, yttrium oxide, titanium carbide, tungsten carbide with 14% cobalt addition, and zirconium carbide. The metal matrix materials were IN 600 nickel and Ti 6/4 titanium. Adhesion of the coatings to all substrates was good except for the NASA-Hough carbon, where flaking off of the oxide coatings in particular was observed.

  4. High performance In2O3 thin film transistors using chemically derived aluminum oxide dielectric

    KAUST Repository

    Nayak, Pradipta K.

    2013-07-18

    We report high performance solution-deposited indium oxide thin film transistors with field-effect mobility of 127 cm2/Vs and an Ion/Ioff ratio of 106. This excellent performance is achieved by controlling the hydroxyl group content in chemically derived aluminum oxide (AlOx) thin-film dielectrics. The AlOx films annealed in the temperature range of 250–350 °C showed higher amount of Al-OH groups compared to the films annealed at 500 °C, and correspondingly higher mobility. It is proposed that the presence of Al-OH groups at the AlOx surface facilitates unintentional Al-doping and efficient oxidation of the indium oxide channel layer, leading to improved device performance.

  5. The influence of titanium and iron oxides on the coloring and friability of the blue fired aluminum oxide as an abrasive material

    OpenAIRE

    E. R. Passos; J. A. Rodrigues

    2016-01-01

    Abstract The quality of abrasive grains is crucial to increase the lifespan of roughing, polishing and cutting tools. The purpose of the work herein was to evaluate the variables of the blue fired aluminum oxide heat treatment process. This heat treatment process improves the physical properties of the brown fused aluminum oxide and results in a blue coloring, which uniquely identifies it within the abrasives industry. The work herein includes information beginning with the electro-fusion pro...

  6. Synthesis and structure analysis of aluminum doped zinc oxide powders

    Institute of Scientific and Technical Information of China (English)

    NIE DengPan; XUE Tao; ZHANG Yu; LI XiangJun

    2008-01-01

    Hexagonal Al-doped zinc oxide (ZnO) powders with a nominal composition of Zn1-xAlxO (0≤x≤0.028) were synthesized by the co-precipitation method. The contents of the Al element in the samples were measured by the inductively coupled plasma-optical emission spectroscopy (ICP-OES) technique. The structures of the Zn1-xAlxO (0≤x≤0.028) compounds calcined at 1000 and 1200℃ have been deter-mined using the Rietveld full-profile analysis method. Rietveld refinements of the diffraction data indi-cated that the addition of Al initially has a considerably positive effect on the decreasing of the lattice parameters a and c of Zn1-xAlxO, but the effect becomes very slight and even negative with the further increase of the Al content. The solid solubility limit of Al in ZnO (mole fraction y) is 2.21%, resulting in Zn0.978Al0.22O. It seems that when the Al content is excessive, Al prefers to form a ZnAl2O4 compound with ZnO, but not to incorporate into the ZnO lattice to occupy the Zn2+ cites. Two phases, [ZnO] (or Al-doped ZnO) and [ZnAl2O4], are obviously segregated in Zn1-xAlxO while the value of x is larger than 0.024. The UV-Vis absorption spectra show that the Al-doped ZnO exhibits a red-shift in the absorption edge without reduced transmission compared with pure ZnO, which also confirms that Al ions enter the ZnO lattice and form a Zn1-xAlxO solid solution.

  7. Synthesis and structure analysis of aluminum doped zinc oxide powders

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Hexagonal Al-doped zinc oxide (ZnO) powders with a nominal composition of Zn1-xAlxO (0≤x≤0.028) were synthesized by the co-precipitation method. The contents of the Al element in the samples were measured by the inductively coupled plasma-optical emission spectroscopy (ICP-OES) technique. The structures of the Zn1-xAlxO (0≤x≤0.028) compounds calcined at 1000 and 1200℃ have been deter- mined using the Rietveld full-profile analysis method. Rietveld refinements of the diffraction data indi- cated that the addition of Al initially has a considerably positive effect on the decreasing of the lattice parameters a and c of Zn1-xAlxO, but the effect becomes very slight and even negative with the further increase of the Al content. The solid solubility limit of Al in ZnO (mole fraction y) is 2.2l%, resulting in Zn0.978Al0.22O. It seems that when the Al content is excessive, Al prefers to form a ZnAl2O4 compound with ZnO, but not to incorporate into the ZnO lattice to occupy the Zn2+ cites. Two phases, [ZnO] (or Al-doped ZnO) and [ZnAl2O4], are obviously segregated in Zn1-xAlxO while the value of x is larger than 0.024. The UV-Vis absorption spectra show that the Al-doped ZnO exhibits a red-shift in the absorption edge without reduced transmission compared with pure ZnO, which also confirms that Al ions enter the ZnO lattice and form a Zn1-xAlxO solid solution.

  8. A Prediction Study of Aluminum Alloy Oxidation of the Fuel Cladding in Jordan Research and Training Reactor

    International Nuclear Information System (INIS)

    U3Si2-Al dispersion fuel with Al cladding will be used for Jordan Research and Training Reactor (JRTR). Aluminum alloy cladding experiences the oxidation layer growth on the surface during the reactor operation. The formation of oxides on the cladding affects fuel performance by increasing fuel temperature. According to the current JRTR fuel management scheme and operation strategy for 5 MW power, a fresh fuel is discharged after 900 effective full power days (EFPD) with 18 cycles of 50 days loading. For the proper prediction of the aluminum oxide thickness of fuel cladding during the long residence time, a reliable model is needed. In this work, several oxide thickness prediction models are compared with the measured data from in-pile test by RERTR program. Moreover, specific parametric studies and a preliminary prediction of the aluminum alloy oxidation using the latest model are performed for JRTR fuel

  9. Method of making highly porous, stable aluminum oxides doped with silicon

    Energy Technology Data Exchange (ETDEWEB)

    Khosravi-Mardkhe, Maryam; Woodfield, Brian F.; Bartholomew, Calvin H.; Huang, Baiyu

    2016-03-22

    The present invention relates to a method for making high surface area and large pore volume thermally stable silica-doped alumina (aluminum oxide) catalyst support and ceramic materials. The ability of the silica-alumina to withstand high temperatures in presence or absence of water and prevent sintering allows it to maintain good activity over a long period of time in catalytic reactions. The method of preparing such materials includes adding organic silicon reagents to an organic aluminum salt such as an alkoxide in a controlled quantity as a doping agent in a solid state, solvent deficient reaction followed by calcination. Alternatively, the organic silicon compound may be added after calcination of the alumina, followed by another calcination step. This method is inexpensive and simple. The alumina catalyst support material prepared by the subject method maintains high pore volumes, pore diameters and surface areas at very high temperatures and in the presence of steam.

  10. Sound Absorption Characteristics of Aluminum Foams Treated by Plasma Electrolytic Oxidation

    Directory of Open Access Journals (Sweden)

    Wei Jin

    2015-11-01

    Full Text Available Open-celled aluminum foams with different pore sizes were fabricated. A plasma electrolytic oxidation (PEO treatment was applied on the aluminum foams to create a layer of ceramic coating. The sound absorption coefficients of the foams were measured by an impedance tube and they were calculated by a transfer function method. The experimental results show that the sound absorption coefficient of the foam increases gradually with the decrease of pore size. Additionally, when the porosity of the foam increases, the sound absorption coefficient also increases. The PEO coating surface is rough and porous, which is beneficial for improvement in sound absorption. After PEO treatment, the maximum sound absorption of the foam is improved to some extent.

  11. Optimization of anodized aluminum oxide pore morphology for GaAs nanowire growth

    Directory of Open Access Journals (Sweden)

    Regine A. Loberternos

    2010-06-01

    Full Text Available Anodic Aluminum oxide films were produced by anodization of sputtered Aluminum thin films on Silicon substrates. The effects of anodization voltage and aqueous oxalic acid solution on the pore diameter and interpore distance were studied. Parameters were sequentially varied to optimize the pore uniformity. Pore morphology was most uniform at 40V anodization voltage and 0.3M solution concentration. Average pore diameter and interpore distance for these parameters are 26.14nm ± 13% and 74.62 ± 8%, respectively. Pore diameter uniformity was further improved by etching with phosphoric acid solution. The AAO films were also successfully used to pattern gold nanoparticle catalysts for the synthesis of semiconductor nanowires.

  12. Electromechanical Breakdown of Barrier-Type Anodized Aluminum Oxide Thin Films Under High Electric Field Conditions

    Science.gov (United States)

    Chen, Jianwen; Yao, Manwen; Yao, Xi

    2016-02-01

    Barrier-type anodized aluminum oxide (AAO) thin films were formed on a polished aluminum substrate via electrochemical anodization in 0.1 mol/L aqueous solution of ammonium pentaborate. Electromechanical breakdown occurred under high electric field conditions as a result of the accumulation of mechanical stress in the film-substrate system by subjecting it to rapid thermal treatment. Before the breakdown event, the electricity of the films was transported in a highly nonlinear way. Immediately after the breakdown event, dramatic cracking of the films occurred, and the cracks expanded quickly to form a mesh-like dendrite network. The breakdown strength was significantly reduced because of the electromechanical coupling effect, and was only 34% of the self-healing breakdown strength of the AAO film.

  13. Study on wear behavior of plasma electrolytic oxidation coatings on aluminum alloy

    Institute of Scientific and Technical Information of China (English)

    CUI Shihai; HAN Jianmin; LI Weijing; KANG Suk-Bong; LEE Jung-Moo

    2006-01-01

    Thick and hard ceramic coatings were fabricated on A356 aluminum alloy by using plasma electrolytic oxidation(PEO) technique.The microstructure and phase composition of the PEO coatings were examined by using SEM and XRD method.It is found that the PEO coatings are mainly composed of crystalline α-Al2O3 and mullite.The dry sliding wear test of PEO coatings were carried out on a ring-on-ring wear machine.Results shows that there is hardly no wear loss of polished PEO coatings while the wear rate of uncoated aluminum alloy is 4.3×10-5 mm3·(N·m)-1 at a speed of 0.52 m·s-1 and a load of 40 N.

  14. Ablation characteristics of aluminum oxide and nitride ceramics during femtosecond laser micromachining

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sung Hoon [School of Information and Mechatronics, Gwangju Institute of Science and Technology (GIST), 1 Oryong-dong Buk-gu, Gwangju 500-712 (Korea, Republic of); Sohn, Ik-Bu [Advanced Photonics Research Institute, Gwangju Institute of Science and Technology (GIST), 1 Oryong-dong Buk-gu, Gwangju 500-712 (Korea, Republic of); Jeong, Sungho, E-mail: shjeong@gist.ac.kr [School of Information and Mechatronics, Gwangju Institute of Science and Technology (GIST), 1 Oryong-dong Buk-gu, Gwangju 500-712 (Korea, Republic of)

    2009-09-30

    Femtosecond laser ablation of aluminum oxide (Al{sub 2}O{sub 3}) and aluminum nitride (AlN) ceramics was performed under normal atmospheric conditions ({lambda} = 785 nm, {tau}{sub p} = 185 fs, repetition rate = 1 kHz), and threshold laser fluencies for single- and multi-pulse ablation were determined. The ablation characteristics of the two ceramics showed similar trends except for surface morphologies, which revealed virtually no melting in Al{sub 2}O{sub 3} but clear evidence of melting for AlN. Based on subsequent X-ray photoelectron spectroscopy (XPS) analyses, the chemistry of these ceramics appeared to remain the same before and after femtosecond laser ablation.

  15. Colloidal infrared reflective and transparent conductive aluminum-doped zinc oxide nanocrystals

    Energy Technology Data Exchange (ETDEWEB)

    Buonsanti, Raffaella; Milliron, Delia J

    2015-02-24

    The present invention provides a method of preparing aluminum-doped zinc oxide (AZO) nanocrystals. In an exemplary embodiment, the method includes (1) injecting a precursor mixture of a zinc precursor, an aluminum precursor, an amine, and a fatty acid in a solution of a vicinal diol in a non-coordinating solvent, thereby resulting in a reaction mixture, (2) precipitating the nanocrystals from the reaction mixture, thereby resulting in a final precipitate, and (3) dissolving the final precipitate in an apolar solvent. The present invention also provides a dispersion. In an exemplary embodiment, the dispersion includes (1) nanocrystals that are well separated from each other, where the nanocrystals are coated with surfactants and (2) an apolar solvent where the nanocrystals are suspended in the apolar solvent. The present invention also provides a film. In an exemplary embodiment, the film includes (1) a substrate and (2) nanocrystals that are evenly distributed on the substrate.

  16. Determining the Effect of Aluminum Oxide Nanoparticles on the Aggregation of Amyloid-Beta in Transgenic Caenorhabditis elegans

    Science.gov (United States)

    Patel, Suhag; Matticks, John; Howell, Carina

    2014-03-01

    The cause of Alzheimer's disease has been linked partially to genetic factors but the predicted environmental components have yet to be determined. In Alzheimer's, accumulation of amyloid-beta protein in the brain forms plaques resulting in neurodegeneration and loss of mental functions. It has been postulated that aluminum influences the aggregation of amyloid-beta. To test this hypothesis, transgenic Caenorhabditis elegans, CL2120, was used as a model organism to observe neurodegeneration in nematodes exposed to aluminum oxide nanoparticles. Behavioral testing, fluorescent staining, and fluorescence microscopy were used to test the effects of aggregation of amyloid-beta in the nervous systems of effected nematodes exposed to aluminum oxide nanoparticles. Energy-dispersive x-ray spectroscopy was used to quantify the total concentration of aluminum oxide that the worms were exposed to during the experiment. Exposure of transgenic and wild type worms to a concentration of 4 mg mL-1 aluminum oxide showed a decrease in the sinusoidal motion, as well as an infirmity of transgenic worms when compared to control worms. These results support the hypothesis that aluminum may play a role in neurodegeneration in C. elegans, and may influence and increase the progression of Alzheimer's disease. This work was supported by National Science Foundation grants DUE-1058829, DMR-0923047 DUE-0806660 and Lock Haven FPDC grants.

  17. Kinetics and thermodynamics of aluminum oxide nanopowder as adsorbent for Fe (III from aqueous solution

    Directory of Open Access Journals (Sweden)

    Mohamed A. Mahmoud

    2015-06-01

    Full Text Available Batch adsorption of Fe (III from aqueous solution by aluminum oxide nanopowder was studied in batch system. The removal efficiency (99.9% was obtained at pH 4 and 50 min contact time. The results indicate that the process follows Langmuir isotherm and pseudo-second-order kinetics model. As well as the thermodynamic data indicated that the exothermic nature process. The values of enthalpy (ΔH°, mean free energy (E and activation energy (Ea indicate that the adsorption process is physical sorption.

  18. Investigation of the radiation defect in aluminum oxide by the spectrum of diffuse reflection

    International Nuclear Information System (INIS)

    Full text : The results of investigation of radiation defects in the γ irradiated disperse aluminum oxide by the spectrum of diffuse reflection were given in this work. It was shown that, γ irradiation Al2O3 guides absorption in and around tied assistance generation of electron (F+) and hole (V) centers. Multicomponent structure was observed in V centers under hv=2,5-3,2 with maximum under γ=375,390 and 410 nm, appropriated hole centers of V, V= and VOH types. The study of kinetic regularity of capital of the V centers depending on absorbed dose. General concentration of the hole centers was calculated

  19. Defects and characteristics of the structure and properties of aluminum oxides

    Science.gov (United States)

    Kopylov, V. B.; Aleksandrov, K. A.; Sergeev, E. V.

    2008-07-01

    Based on IR spectroscopy data, it was established that nonstoichiometry defects in the structure of aluminum oxides were components of the Wannier-Mott exciton states and included the Al-O, Al-Al, O2, O{2/+}, O{2/-}, O{2/2-}, O3, and O2 n isolated oscillators in the ground and electronically excited states. It was shown that their presence manifested itself by thermoemission of molecular oxygen singlet forms, excess heat capacity, and anomalous diamagnetism at elevated temperatures.

  20. Rayleigh instability in polymer thin films coated in the nanopores of anodic aluminum oxide templates.

    Science.gov (United States)

    Tsai, Chia-Chan; Chen, Jiun-Tai

    2014-01-14

    We study the Rayleigh instability of polystyrene (PS) thin films coated in the nanopores of anodic aluminum oxide (AAO) templates. After thermal annealing, the surface of the PS thin films undulates and the nanostructures transform from nanotubes to Rayleigh-instability-induced nanostructures (short nanorods with encapsulated air bubbles). With longer annealing times, the nanostructures further transform to nanorods with longer lengths. PS samples with two different molecular weights (24 and 100 kg/mol) are used, and their instability transformation processes are compared. The morphology diagrams of the nanostructures at different stages are also constructed to elucidate the mechanism of the morphology transformation. PMID:24380368

  1. A Single-Tube Nucleic Acid Extraction, Amplification, and Detection Method Using Aluminum Oxide

    OpenAIRE

    Dames, Shale; Bromley, L. Kathryn; Herrmann, Mark; Elgort, Marc; Erali, Maria; Smith, Roger; Voelkerding, Karl V.

    2006-01-01

    A disposable 0.2-ml polymerase chain reaction (PCR) tube modified with an aluminum oxide membrane (AOM) has been developed for the extraction, amplification, and detection of nucleic acids. To assess the dynamic range of AOM tubes for real-time PCR, quantified herpes simplex virus (HSV) DNA was used to compare AOM tubes to standard PCR tubes. AOM PCR tubes used for amplification and detection of quantified HSV-1 displayed a crossing threshold (CT) shift 0.1 cycles greater than PCR tube contro...

  2. Photoluminescence emission of nanoporous anodic aluminum oxide films prepared in phosphoric acid

    Science.gov (United States)

    Nourmohammadi, Abolghasem; Asadabadi, Saeid Jalali; Yousefi, Mohammad Hasan; Ghasemzadeh, Majid

    2012-12-01

    The photoluminescence emission of nanoporous anodic aluminum oxide films formed in phosphoric acid is studied in order to explore their defect-based subband electronic structure. Different excitation wavelengths are used to identify most of the details of the subband states. The films are produced under different anodizing conditions to optimize their emission in the visible range. Scanning electron microscopy investigations confirm pore formation in the produced layers. Gaussian analysis of the emission data indicates that subband states change with anodizing parameters, and various point defects can be formed both in the bulk and on the surface of these nanoporous layers during anodizing.

  3. Field emission properties of low-density carbon nanotubes prepared on anodic aluminum-oxide template

    International Nuclear Information System (INIS)

    Anodic aluminum-oxide (AAO) templates were fabricated by two-step anodizing an Al film. After the Co catalyst had been electrochemically deposited onto the bottom of the AAO template, carbon nanotubes (CNTs) were grown by using catalytic pyrolysis of C2H2 and H2 at 650 .deg. C. Overgrowth of CNTs with low density on the AAO templates was observed. The field-emission measurements on the samples showed a turn-on field of 2.17 V/μm and a field enhancement factor of 5700. The emission pattern on a phosphor screen was quite homogeneous over the area at a relatively low electric field.

  4. Preparation and Characterization of Fe Nanowire Arrays Embedded in Porous Anodic Aluminum Oxide Templates

    Institute of Scientific and Technical Information of China (English)

    迟广俊; 姚素薇

    2004-01-01

    Fe nanowire arrays are prepared by electrodeposition in porous anodic aluminum oxide template from a composite electrolyte solution. These nanowires have an uniform diameter of approximate 25 nm and a length in excess of 2.5μm.The micrographs and crystal structures of Fe nanowlres are studied by transmission electron microscopy (TEM), selected-area electron diffraction (SAED), and X-ray diffraction(XRD). It is found that each nanowire is essentially a single crystal and has a different orientation in each array. Hysteresis loops of Fe nanowire array show that its easy magnetization direction is perpendicular to the sample plane.

  5. Hydrogenation of Levulinic Acid over Nickel Catalysts Supported on Aluminum Oxide to Prepare γ-Valerolactone

    OpenAIRE

    Jie Fu; Dong Sheng; Xiuyang Lu

    2015-01-01

    Four types of nickel catalysts supported on aluminum oxide (Ni/Al2O3) with different nickel loadings were synthesized using the co-precipitation method and were used for the hydrogenation of levulinic acid (LA) to prepare γ-valerolactone (GVL). The synthesized Ni/Al2O3 catalysts exhibited excellent catalytic activity in dioxane, and the activity of the catalysts was excellent even after being used four times in dioxane. The catalytic activity in dioxane as a solvent was found to be superior t...

  6. The uniformity of Al distribution in aluminum-doped zinc oxide films grown by atomic layer deposition

    Energy Technology Data Exchange (ETDEWEB)

    Luka, G., E-mail: gluka@ifpan.edu.pl [Institute of Physics, Polish Academy of Sciences, Warsaw (Poland); Wachnicki, L.; Witkowski, B.S.; Krajewski, T.A.; Jakiela, R.; Guziewicz, E. [Institute of Physics, Polish Academy of Sciences, Warsaw (Poland); Godlewski, M. [Institute of Physics, Polish Academy of Sciences, Warsaw (Poland); Department of Mathematics and Natural Sciences, College of Science, Cardinal Stefan Wyszynski University, Warsaw (Poland)

    2011-02-25

    We investigated the aluminum distribution in aluminum-doped zinc oxide films grown by atomic layer deposition. Surface morphology, structure, composition and electrical properties of obtained films were studied. For the aluminum content less than 2 at.%, a periodicity of Al distribution along the layer depth was observed. This periodicity diminished significantly after annealing the samples in nitrogen atmosphere at 300 deg. C. For the Al content higher than 2 at.%, its distribution in ZnO:Al films was uniform within the depth measurement accuracy of {approx}5-10 nm.

  7. Effect of environment on iodine oxidation state and reactivity with aluminum.

    Science.gov (United States)

    Smith, Dylan K; McCollum, Jena; Pantoya, Michelle L

    2016-04-20

    Iodine oxide is a highly reactive solid oxidizer and with its abundant generation of iodine gas during reaction, this oxidizer also shows great potential as a biocidal agent. A problem with using I2O5 in an energetic mixture is its highly variable reactive behavior. This study isolates the variable reactivity associated with I2O5 as a function of its chemical reaction in various environments. Specifically, aluminum fuel and iodine oxide powder are combined using a carrier fluid to aid intermixing. The carrier fluid is shown to significantly affect the oxidation state of iodine oxide, thereby affecting the reactivity of the mixture. Four carrier fluids were investigated ranging in polarity and water miscibility in increasing order from hexane water as well as untreated, dry-mixed reactants. Oxidation state and reactivity were examined with experimental techniques including X-ray photoelectric spectroscopy (XPS) and differential scanning calorimetry (DSC). Results are compared with thermal equilibrium simulations. Flame speeds increased with polarity of the fluid used to intermix the powder and ranged from 180 to 1202 m s(-1). The I2O5 processed in the polar fluids formed hydrated states of iodine oxide: HIO3 and HI3O8; and, the nonpolar and dry-mixed samples formed: I2O4 and I4O9. During combustion, the hydrated iodine oxides rapidly dehydrated from HIO3 to HI3O8 and from HI3O8 to I2O5. Both steps release 25% of their mass as vapor during combustion. Increased gas generation enhances convective energy transport and accounts for the increase in reactivity seen in the mixtures processed in polar fluids. These results explain the chemical mechanisms underlying the variable reactivity of I2O5 that are a function of the oxide's highly reactive nature with its surrounding environment. These results will significantly impact the selection of carrier fluid in the synthesis approach for iodine containing reactive mixtures. PMID:27052472

  8. Study on phosphating treatment of aluminum alloy: role of yttrium oxide

    Institute of Scientific and Technical Information of China (English)

    ZHANG Shenglin

    2009-01-01

    Zinc phosphate coatings formed on 6061-Al alloy, after dipping in phosphating solutions containing different amounts of Y2O3(yttrium oxide), were studied by scanning electron microscopy (SEM), X-ray diffraction (XRD) and electrochemical measurements. Significant variations in the morphology and corrosion resistance afforded by zinc phosphate coating were especially observed as Y2O3 in phosphating solution varied from 0 to 40 mg/L. The addition of Y2O3 changed the initial potential of the interface between aluminum alloy substrate and phosphating solution and increased the number of nucleation sites. The phosphate coating thereby was less porous structure and covered the surface of aluminum alloy completely within short phosphating time. Phosphate coating was mainly composed of Zn3(PO4)2-4H2O (hopeite) and AIPO4(aluminum phosphate). Y2O3, as an additive of phosphatization, accelerated precipitation and refined the gain size of phosphate coating. The corrosion resistance of zinc phosphate coating in 3% NaCl solution was improved as shown by po-larization measurement. In the present research, the optimal amount of Y2O3 was 10-20 mg/L, and the optimal phosphating time was 600 s.

  9. Impurity-defect structure of anodic aluminum oxide produced by two-sided anodizing in tartaric acid

    Science.gov (United States)

    Chernyakova, K. V.; Vrublevsky, I. A.; Ivanovskaya, M. I.; Kotsikau, D. A.

    2012-03-01

    Porous aluminum oxide is prepared in a 0.4 M aqueous solution of tartaric acid by two-sided anodizing. Fourier Transform IR spectroscopy (FTIR) data reveal the presence, in the alumina, of unoxidized tartarate ions, as well as products of their partial (radical organic products and CO) and complete (CO2) oxidation. Carboxylate ions and elemental carbon contained in the anodic oxide impart a gray color to the films.

  10. Plasmon-induced optical switching of electrical conductivity in porous anodic aluminum oxide films encapsulated with silver nanoparticle arrays.

    Science.gov (United States)

    Huang, Chen-Han; Lin, Hsing-Ying; Lau, Ben-Chao; Liu, Chih-Yi; Chui, Hsiang-Chen; Tzeng, Yonhua

    2010-12-20

    We report on plasmon induced optical switching of electrical conductivity in two-dimensional (2D) arrays of silver (Ag) nanoparticles encapsulated inside nanochannels of porous anodic aluminum oxide (AAO) films. The reversible switching of photoconductivity greatly enhanced by an array of closely spaced Ag nanoparticles which are isolated from each other and from the ambient by thin aluminum oxide barrier layers are attributed to the improved electron transport due to the localized surface plasmon resonance and coupling among Ag nanoparticles. The photoconductivity is proportional to the power, and strongly dependent on the wavelength of light illumination. With Ag nanoparticles being isolated from the ambient environments by a thin layer of aluminum oxide barrier layer of controlled thickness in nanometers to tens of nanometers, deterioration of silver nanoparticles caused by environments is minimized. The electrochemically fabricated nanostructured Ag/AAO is inexpensive and promising for applications to integrated plasmonic circuits and sensors. PMID:21197062

  11. Effects of rare earth oxide additives on the thermal behaviors of aluminum nitride ceramics

    Institute of Scientific and Technical Information of China (English)

    YAO Yijun; WANG Ling; LI Chuncheng; JIANG Xiaolong; QIU Tai

    2009-01-01

    The effects of Y_2O_3 and Er_2O_3 on the sintering behaviors, thermal properties and microstructure of AIN ceramics were investigated. The ex-perimental results show that the sintering temperature can be decreased; the relative density and thermal behavior can be improved by adding rare earth oxide in AIN ceramics. For AIN ceramics with 3 wt.% Er_2O_3 additive, the relative density is 98.8%, and the thermal conductivity reaches 106 W·m~(-1)·K~(-1). The microstructure research found that no obvious aluminum erbium oxide was found in AIN ceramics doped with 3 wt.% Er_2O_3, which favored the improvement of the thermal conductivity of AIN ceramics.

  12. Radon test measurements with Ce-doped yttrium aluminum oxide perovskite scintillator

    Directory of Open Access Journals (Sweden)

    F. de Notaristefani

    2002-04-01

    Full Text Available Scintillation properties of a Ce-doped yttrium aluminium oxide perovskite monocrystal optically coupled to a Hamamatsu H5784 photomultiplier are analyzed with a standard bialkali photocathode for radon and radon daughters gamma-ray spectrometry. Tests in water up to 100°C and in acidic solutions of HCl (37%, H2SO4 (48% and HNO3 (65% were performed to simulate environments of geophysical interest, such as geothermal and volcanic areas. Comparative measurements with standard radon sources provided by the National Institute for Metrology of Ionizing Radiations (ENEA confirm the non-hygroscopic properties of the scintillator and small dependence of the light yield on temperature and HNO3.The Ce-doped yttrium aluminum oxide perovskite monocrystal shows high response stability for radon gamma-ray spectrometry in environments with large temperature gradients and high acid concentrations.

  13. The application of the barrier-type anodic oxidation method to thickness testing of aluminum films

    Science.gov (United States)

    Chen, Jianwen; Yao, Manwen; Xiao, Ruihua; Yang, Pengfei; Hu, Baofu; Yao, Xi

    2014-09-01

    The thickness of the active metal oxide film formed from a barrier-type anodizing process is directly proportional to its formation voltage. The thickness of the consumed portion of the metal film is also corresponding to the formation voltage. This principle can be applied to the thickness test of the metal films. If the metal film is growing on a dielectric substrate, when the metal film is exhausted in an anodizing process, because of the high electrical resistance of the formed oxide film, a sudden increase of the recorded voltage during the anodizing process would occur. Then, the thickness of the metal film can be determined from this voltage. As an example, aluminum films are tested and discussed in this work. This method is quite simple and is easy to perform with high precision.

  14. Hydrogen plasma treatment for improved conductivity in amorphous aluminum doped zinc tin oxide thin films

    Directory of Open Access Journals (Sweden)

    M. Morales-Masis

    2014-09-01

    Full Text Available Improving the conductivity of earth-abundant transparent conductive oxides (TCOs remains an important challenge that will facilitate the replacement of indium-based TCOs. Here, we show that a hydrogen (H2-plasma post-deposition treatment improves the conductivity of amorphous aluminum-doped zinc tin oxide while retaining its low optical absorption. We found that the H2-plasma treatment performed at a substrate temperature of 50 °C reduces the resistivity of the films by 57% and increases the absorptance by only 2%. Additionally, the low substrate temperature delays the known formation of tin particles with the plasma and it allows the application of the process to temperature-sensitive substrates.

  15. Anodic aluminum oxide with fine pore size control for selective and effective particulate matter filtering

    Science.gov (United States)

    Zhang, Su; Wang, Yang; Tan, Yingling; Zhu, Jianfeng; Liu, Kai; Zhu, Jia

    2016-07-01

    Air pollution is widely considered as one of the most pressing environmental health issues. Particularly, atmospheric particulate matters (PM), a complex mixture of solid or liquid matter suspended in the atmosphere, are a harmful form of air pollution due to its ability to penetrate deep into the lungs and blood streams, causing permanent damages such as DNA mutations and premature death. Therefore, porous materials which can effectively filter out particulate matters are highly desirable. Here, for the first time, we demonstrate that anodic aluminum oxide with fine pore size control fabricated through a scalable process can serve as effective and selective filtering materials for different types of particulate matters (such as PM2.5, PM10). Combining selective and dramatic filtering effect, fine pore size control and a scalable process, this type of anodic aluminum oxide templates can potentially serve as a novel selective filter for different kinds of particulate matters, and a promising and complementary solution to tackle this serious environmental issue.

  16. Barrier layer non-uniformity effects in anodized aluminum oxide nanopores on ITO substrates

    International Nuclear Information System (INIS)

    Nanoporous anodic aluminum oxide (AAO) has been used widely as a template for device fabrication. In many nanostructured electro-optical device designs, AAO grown on an ITO substrate is the desired configuration. However, a residual thin aluminum oxide barrier layer between ITO and the AAO pores remains and process non-uniformities during the template fabrication can cause serious problems in the quality of nanowires deposited later in these pores. It was observed that in many templates, even the pores closest to each other could have their barrier layer thicknesses differ by as much as 10-20 nm. In this paper, causes and remedies for this non-uniformity are investigated, including the effects of a thin Ti interlayer inserted between the ITO and AAO. Templates with different Ti layer thickness and annealing conditions were compared. Mechanisms for the formation of voids beneath the barrier layer were analyzed and studied experimentally. Reactive ion etch (RIE) was found to be the preferred method to mitigate process non-uniformities. Using the above methods, barrier-free AAO templates on ITO substrates were obtained; their thicknesses ranged from 200 to 1000 nm. The characteristics of CdS nanowires electrodeposited into the initial templates with non-uniform barrier layer thicknesses and into the processed, barrier-free templates were compared.

  17. Analysis of anti-condensation mechanism on superhydrophobic anodic aluminum oxide surface

    International Nuclear Information System (INIS)

    Wetting theory about superhydrophobic surfaces reveals that hydrophobicity of surfaces has great relationship with surface roughness and surface free energy. Adopt electrochemical plus fluorine silane modified method to prepare superhydrophobic surface on anodic aluminum oxide surface, which not only enhances surface roughness, but also reduces surface free energy, even the static contact angle can reach 159.2° and anti-condensation is authenticated. Based on the experimental findings, analyze the reason of anti-condensation on superhydrophobic surfaces: one is that the density of droplets formed on superhydrophobic surfaces is low and the number of droplets is little; the other is bigger static contact angle and smaller rolling angle on superhydrophobic surfaces make droplets easy to detach on smaller tilt angle. This research can solve some condensation problems of equipment using in HVAC systems, such as heat exchangers in air conditioning system, cold radiation boards, air supply outlets, and so on. Highlights: • Prepare superhydrophobic surface on anodic aluminum oxide surface. • Analyze the reason of anti-condensation on superhydrophobic surfaces. • The density of droplets formed on superhydrophobic surfaces is low. • Droplets on superhydrophobic surfaces are easy to detach. • This research can solve some problems of equipment using in HVAC systems

  18. Characterization of lipid bilayer formation in aligned nanoporous aluminum oxide nanotube arrays.

    Science.gov (United States)

    Karp, Ethan S; Newstadt, Justin P; Chu, Shidong; Lorigan, Gary A

    2007-07-01

    Aligning lipid bilayers in nanoporous anodized aluminum oxide (AAO) is a new method to help study membrane proteins by electron paramagnetic resonance (EPR) and solid-state nuclear magnetic resonance (NMR) spectroscopic methods. The ability to maintain hydration, sample stability, and compartmentalization over long periods of time, and to easily change solvent composition are major advantages of this new method. To date, 1,2-dimyristoyl-sn-glycero-3-phosphatidylcholine (DMPC) has been the only phospholipid used for membrane protein studies with AAO substrates. The different properties of lipids with varying chain lengths require modified sample preparation procedures to achieve well formed bilayers within the lining of the AAO substrates. For the first time, the current study presents a simple methodology to incorporate large quantities of 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphatidylcholine (POPC), DMPC, and 1,2-dipalmitoyl-3-sn-phosphatidylcholine (DPPC) phospholipids inside AAO substrate nanopores of varying sizes. (2)H and (31)P solid-state NMR were used to confirm the alignment of each lipid and compare the efficiency of alignment. This study is the first step in standardizing the use of AAO substrates as a tool in NMR and EPR and will be useful for future structural studies of membrane proteins. Additionally, the solid-state NMR data suggest possible applications of nanoporous aluminum oxide in future vesicle fusion studies. PMID:17482492

  19. New roots to formation of nanostructures on glass surface through anodic oxidation of sputtered aluminum

    Directory of Open Access Journals (Sweden)

    Satoru Inoue, Song-Zhu Chu, Kenji Wada, Di Li and Hajime Haneda

    2003-01-01

    Full Text Available New processes for the preparation of nanostructure on glass surfaces have been developed through anodic oxidation of sputtered aluminum. Aluminum thin film sputtered on a tin doped indium oxide (ITO thin film on a glass surface was converted into alumina by anodic oxidation. The anodic alumina gave nanometer size pore array standing vertically on the glass surface. Kinds of acids used in the anodic oxidation changed the pore size drastically. The employment of phosphoric acid solution gave several tens nanometer size pores. Oxalic acid cases produced a few tens nanometer size pores and sulfuric acid solution provided a few nanometer size pores. The number of pores in a unit area could be changed with varying the applied voltage in the anodization and the pore sizes could be increased by phosphoric acid etching. The specimen consisting of a glass substrate with the alumina nanostructures on the surface could transmit UV and visible light. An etched specimen was dipped in a TiO2 sol solution, resulting in the impregnation of TiO2 sol into the pores of alumina layer. The TiO2 sol was heated at ~400 °C for 2 h, converting into anatase phase TiO2. The specimens possessing TiO2 film on the pore wall were transparent to the light in UV–Visible region. The electro deposition technique was applied to the introduction of Ni metal into pores, giving Ni nanorod array on the glass surface. The removal of the barrier layer alumina at the bottom of the pores was necessary to attain smooth electro deposition of Ni. The photo catalytic function of the specimens possessing TiO2 nanotube array was investigated in the decomposition of acetaldehyde gas under the irradiation of UV light, showing that the rate of the decomposition was quite large.

  20. Photoluminescence blue shift of indium phosphide nanowire networks with aluminum oxide coating

    Energy Technology Data Exchange (ETDEWEB)

    Fryauf, David M.; Zhang, Junce; Norris, Kate J.; Diaz Leon, Juan J.; Oye, Michael M.; Kobayashi, Nobuhiko P. [Nanostructured Energy Conversion Technology and Research (NECTAR), Advanced Studies Laboratories, University of California, Santa Cruz, CA (United States); Baskin School of Engineering, University of California Santa Cruz, Santa Cruz, CA (United States); NASA Ames Research Center, Moffett Field, CA (United States); Wei, Min [Baskin School of Engineering, University of California Santa Cruz, Santa Cruz, CA (United States); School of Micro-Electronics and Solid-Electronics, University of Electronic Science and Technology of China, Chengdu (China)

    2014-07-15

    This paper describes our finding that optical properties of semiconductor nanowires were modified by depositing a thin layer of metal oxide. Indium phosphide nanowires were grown by metal organic chemical vapor deposition on silicon substrates with gold catalyst resulting in three-dimensional nanowire networks, and optical properties were obtained from the collective nanowire networks. The networks were coated with an aluminum oxide thin film deposited by plasma-enhanced atomic layer deposition. We studied the dependence of the peak wavelength of photoluminescence spectra on the thickness of the oxide coatings. A continuous blue shift in photoluminescence spectra was observed when the thickness of the oxide coating was increased. The observed blue shift is attributed to the Burstein-Moss effect due to increased carrier concentration in the nanowire cores caused by repulsion from intrinsic negative fixed charges located at the inner oxide surface. Samples were further characterized by scanning electron microscopy, Raman spectroscopy, transmission electron microscopy, and selective area diffractometry to better understand the physical mechanisms for the blue shift. (copyright 2014 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  1. Fabrication of high quality anodic aluminum oxide (AAO) on low purity aluminum—A comparative study with the AAO produced on high purity aluminum

    International Nuclear Information System (INIS)

    Highlights: • Nanoporous alumina was fabricated by anodization in sulfuric acid solution with glycol. • The AAO manufacturing on low- and high-purity Al was compared. • The pores size was ranging between 30 and 50 nm. • No difference in the quality of the AAO fabricated on both Al types was observed. • The current vs. anodization time curves were recorded. -- Abstract: In this work the quality, arrangement, composition, and regularity of nanoporous AAO formed on the low-purity (AA1050) and high-purity aluminum during two-step anodization in a mixture of sulfuric acid solution (0.3 M), water and glycol (3:2, v/v), at various voltages (15, 20, 25, 30, 35 V) and at temperature of −1 °C, are investigated. The electrochemical conditions have allowed to obtain pores with the size ranging from 30 to 50 nm, which are much larger than those usually obtained by anodization in a pure sulfuric acid solution (<20 nm). The mechanism of the AAO growth is discussed. It was found that with the increase of applied anodizing voltage a number of incorporated sulfate ions in the aluminum oxide matrix increases, which was connected with the appearance of an unusual area in the current vs. time curves. On the surface of anodizing low- and high-purity aluminum, the formation of hillocks was observed, which was associated with the sulfate ions incorporation. The sulfate ions are replacing the oxygen atom/atoms in the AAO amorphous crystal structure and, consequently, the AAO template swells, the oxide cracks and uplifts causing the formation of hillocks. The same mechanism occurs for both low- and high-purity aluminum. Nanoporous AAO characterized by a very high regularity, not registered previously for low purity aluminum, was obtained. Furthermore, no significant difference in the regularity ratio between the AAO obtained on low- and high-purity aluminum, was observed. The electrochemical conditions applied in this study can be, thus, used for the fabrication of high quality

  2. A Prediction Study on Oxidation of Aluminum Alloy Cladding of U3Si2-Al Fuel Plate

    International Nuclear Information System (INIS)

    U3Si2-Al dispersion fuel with aluminum alloy cladding will be used for the Jordan Research and Training Reactor (JRTR). Aluminum alloy cladding undergoes corrosion at slow rates under operational status. This causes thinning of the cladding walls and impairs heat transfer to the coolant. Predictions of the aluminum oxide thickness of the fuel cladding and the maximum temperature difference across the oxide film are needed for reliability evaluation based on the design criteria and limits which prohibit spallation of oxide film. In this work, several oxide thickness prediction models were compared with the measured data of in-pile test results from RERTR program. Moreover, specific parametric studies and a preliminary prediction of the aluminum alloy oxidation using the latest model were performed for JRTR fuel. According to the current JRTR fuel management scheme and operation strategy for 5 MW power, fresh fuel is discharged after 900 effective full power days (EFPD), which is too long a span to predict oxidation properly without an elaborate model. The latest model developed by Kim et al. is in good agreement with the recent in-pile test data as well as with the out-of-pile test data available in the literature, and is one of the best predictors for the oxidation of aluminum alloy cladding in various operating condition. Accordingly, this model was chosen for estimating the oxide film thickness. Through the preliminarily evaluation, water pH level is to be controlled lower than 6.2 for the conservativeness in the case of including the effect of anticipated operational occurrences and the spent fuel residence time in the storage rack after discharging. (author)

  3. Comparative Assessment of Antimicrobial Efficiency of Ionic Silver, Silver Monoxide, and Metallic Silver Incorporated onto an Aluminum Oxide Nanopowder Carrier

    OpenAIRE

    Agnieszka Maria Jastrzębska; Ewa Karwowska; Andrzej R. Olszyna; Antoni R. Kunicki

    2013-01-01

    The present paper provides comparative assessment of antimicrobial efficiency of ionic silver (Ag+), silver monoxide (Ag2O), and metallic silver (Ag) incorporated onto an aluminum oxide nanopowder carrier (Al2O3). The deposition of Ag+ ions, Ag2O nanoparticles, and Ag nanoparticles on an different phases of aluminum oxide nanopowder carrier was realized using consecutive stages of dry sol-gel method. The Al2O3-Ag+, Al2O3-Ag2O, and Al2O3-Ag nanopowders were widely characterized qualitatively a...

  4. Murine pulmonary responses after sub-chronic exposure to aluminum oxide-based nanowhiskers

    Directory of Open Access Journals (Sweden)

    Adamcakova-Dodd Andrea

    2012-06-01

    Full Text Available Abstract Background Aluminum oxide-based nanowhiskers (AO nanowhiskers have been used in manufacturing processes as catalyst supports, flame retardants, adsorbents, or in ceramic, metal and plastic composite materials. They are classified as high aspect ratio nanomaterials. Our aim was to assess in vivo toxicity of inhaled AO nanowhisker aerosols. Methods Primary dimensions of AO nanowhiskers specified by manufacturer were 2–4 nm x 2800 nm. The aluminum content found in this nanomaterial was 30% [mixed phase material containing Al(OH3 and AlOOH]. Male mice (C57Bl/6 J were exposed to AO nanowhiskers for 4 hrs/day, 5 days/wk for 2 or 4 wks in a dynamic whole body exposure chamber. The whiskers were aerosolized with an acoustical dry aerosol generator that included a grounded metal elutriator and a venturi aspirator to enhance deagglomeration. Average concentration of aerosol in the chamber was 3.3 ± 0.6 mg/m3 and the mobility diameter was 150 ± 1.6 nm. Both groups of mice (2 or 4 wks exposure were necropsied immediately after the last exposure. Aluminum content in the lung, heart, liver, and spleen was determined. Pulmonary toxicity assessment was performed by evaluation of bronchoalveolar lavage (BAL fluid (enumeration of total and differential cells, total protein, activity of lactate dehydrogenase [LDH] and cytokines, blood (total and differential cell counts, lung histopathology and pulmonary mechanics. Results Following exposure, mean Al content of lungs was 0.25, 8.10 and 15.37 μg/g lung (dry wt respectively for sham, 2 wk and 4 wk exposure groups. The number of total cells and macrophages in BAL fluid was 2-times higher in animals exposed for 2 wks and 6-times higher in mice exposed for 4 wks, compared to shams (p p  Conclusions Sub-chronic inhalation exposures to aluminum-oxide based nanowhiskers induced increased lung macrophages, but no inflammatory or toxic responses were observed.

  5. High stability mechanisms of quinary indium gallium zinc aluminum oxide multicomponent oxide films and thin film transistors

    International Nuclear Information System (INIS)

    Quinary indium gallium zinc aluminum oxide (IGZAO) multicomponent oxide films were deposited using indium gallium zinc oxide (IGZO) target and Al target by radio frequency magnetron cosputtering system. An extra carrier transport pathway could be provided by the 3 s orbitals of Al cations to improve the electrical properties of the IGZO films, and the oxygen instability could be stabilized by the strong Al-O bonds in the IGZAO films. The electron concentration change and the electron mobility change of the IGZAO films for aging time of 10 days under an air environment at 40 °C and 75% humidity were 20.1% and 2.4%, respectively. The experimental results verified the performance stability of the IGZAO films. Compared with the thin film transistors (TFTs) using conventional IGZO channel layer, in conducting the stability of TFTs with IGZAO channel layer, the transconductance gm change, threshold voltage VT change, and the subthreshold swing S value change under the same aging condition were improved to 7.9%, 10.5%, and 14.8%, respectively. Furthermore, the stable performances of the IGZAO TFTs were also verified by the positive gate bias stress. In this research, the quinary IGZAO multicomponent oxide films and that applied in TFTs were the first studied in the literature

  6. Oxidation Behavior of In-Flight Molten Aluminum Droplets in the Twin-Wire Electric Arc Thermal Spray Process

    Energy Technology Data Exchange (ETDEWEB)

    Donna Post Guillen; Brian G. Williams

    2005-05-01

    This paper examines the in-flight oxidation of molten aluminum sprayed in air using the twin-wire electric arc (TWEA) thermal spray process. The oxidation reaction of aluminum in air is highly exothermic and is represented by a heat generation term in the energy balance. Aerodynamic shear at the droplet surface enhances the amount of in-flight oxidation by: (1) promoting entrainment and mixing of the surface oxides within the droplet, and (2) causing a continuous heat generation effect that increases droplet temperature over that of a droplet without internal circulation. This continual source of heat input keeps the droplets in a liquid state during flight. A linear rate law based on the Mott-Cabrera theory was used to estimate the growth of the surface oxide layer formed during droplet flight. The calculated oxide volume fraction of an average droplet at impact agrees well with the experimentally determined oxide content for a typical TWEA-sprayed aluminum coating, which ranges from 3.3 to 12.7%. An explanation is provided for the elevated, nearly constant surface temperature (~ 2000 oC) of the droplets during flight to the substrate and shows that the majority of oxide content in the coating is produced during flight, rather than after deposition.

  7. Effect of interfacial oxide thickness on the photocatalytic activity of magnetron-sputtered TiO2coatings on aluminum substrate

    DEFF Research Database (Denmark)

    Daviðsdóttir, Svava; Petit, Jean-Pierre; Shabadi, Rajashekhara;

    2015-01-01

    measurements showed a maximum UV-light absorption by titanium dioxide occurring slightly prior to the energy of the maximum photocurrent. The photocurrent of titanium dioxide decreases with increasing thickness of the aluminum oxide interface layer. Aluminum oxide acts as an insulator; disfavoring the electron...

  8. Effect of interfacial oxide thickness on the photocatalytic activity of magnetron-sputtered TiO2 coatings on aluminum substrate

    DEFF Research Database (Denmark)

    Daviðsdóttir, Svava; Petit, Jean-Pierre; Shabadi, Rajashekhara;

    2015-01-01

    measurements showed a maximum UV-light absorption by titanium dioxide occurring slightly prior to the energy of the maximum photocurrent. The photocurrent of titanium dioxide decreases with increasing thickness of the aluminum oxide interface layer. Aluminum oxide acts as an insulator; disfavoring the electron...

  9. Geant4 simulation of zinc oxide nanowires in anodized aluminum oxide template as a low energy X-ray scintillator detector

    International Nuclear Information System (INIS)

    In this work, ZnO nanowires in anodized aluminum oxide nanoporous template are proposed as an architecture for development of new generation of scintillator based X-ray imagers. The optical response of crystalline ordered ZnO nanowire arrays in porous anodized aluminum oxide template under 20 keV X-ray illumination is simulated using the Geant4 Monte Carlo code. The results show that anodized aluminum oxide template has a special impact as a light guide to conduct the optical photons induced by X-ray toward the detector thickness and to decrease the light scattering in detector volume. This inexpensive and effective method can significantly improve the spatial resolution in scintillator based X-ray imagers, especially in medical applications.

  10. X-ray photoelectron spectroscopy study of the stability of Fomblin Z25 on the native oxide of aluminum

    Science.gov (United States)

    Herrera-Fierro, Pilar; Pepper, Stephen V.; Jones, William R.

    1992-01-01

    Thin films of Fomblin Z25, a perfluoropolyalkylether lubricant, were vapor deposited onto clean, oxidized aluminum, and onto sapphire surfaces, and their behavior at different temperatures was studied using X-ray photoelectron spectroscopy and temperature desorption spectroscopy (TDS). The interfacial fluid molecules decompose on the native oxide at room temperature, and continue to decompose at elevated temperatures, as previous studies had shown to occur on the clean metal. TDS indicated that different degradation mechanisms were operative for clean and oxidized aluminum. On sapphire substrates, no reaction was observed at room temperature. The native oxide of aluminum is neither passive nor protective towards Fomblin Z25. At higher temperatures (150 C), degradation of the polymer on sapphire produced a debris layer at the interface with a chemical composition similar to the one formed on aluminum oxide. Rubbing a Fomblin film on a single crystal sapphire also induced the decomposition of the lubricant in contact with the interface and the formation of a debris layer.

  11. Role of aluminum doping on phase transformations in nanoporous titania anodic oxides

    International Nuclear Information System (INIS)

    The role of aluminium doping on anatase to rutile phase transformation of nanoporous titanium oxide films were investigated. For this purpose pure and aluminum doped metal films were deposited on alumina substrates by cathodic arc physical deposition. The nanoporous anodic oxides were prepared by porous anodizing of pure and aluminum doped titanium metallic films in an ethylene glycol + NH4F based electrolyte. Nanoporous amorphous structures with 60–80 nm diameter and 2–4 μm length were formed on the surfaces of alumina substrates. The amorphous undoped and Al-doped TiO2 anodic oxides were heat-treated at different temperatures in the range of 280–720 °C for the investigation of their crystallization behavior. The combined effects of nanoporous structure and Al doping on crystallization behavior of titania were investigated using X-ray diffraction (XRD) and micro Raman analysis. The results indicated that both Al ions incorporated into the TiO2 structure and the nanoporous structure retarded the rutile formation. It was also revealed that presence or absence of metallic film underneath the nanopores has a major contribution to anatase-rutile transformation. - Highlights: • Al-doped TiO2 nanopores were grown on alumina substrates using anodization method. • The crystallization behavior of nanoporous Al-doped TiO2 were investigated. • Al doping into nanoporous TiO2 retarded the anatase-rutile transformation. • Nanostructuring has significant role in controlling rutile formation temperature. • The absence of the metallic film under the nanopores delayed the rutile formation

  12. Role of aluminum doping on phase transformations in nanoporous titania anodic oxides

    Energy Technology Data Exchange (ETDEWEB)

    Bayata, Fatma [Istanbul Bilgi University, Department of Mechanical Engineering, 34060, Eyup, Istanbul (Turkey); Ürgen, Mustafa, E-mail: urgen@itu.edu.tr [Istanbul Technical University, Department of Metallurgical and Materials Engineering, 34469, Maslak, Istanbul (Turkey)

    2015-10-15

    The role of aluminium doping on anatase to rutile phase transformation of nanoporous titanium oxide films were investigated. For this purpose pure and aluminum doped metal films were deposited on alumina substrates by cathodic arc physical deposition. The nanoporous anodic oxides were prepared by porous anodizing of pure and aluminum doped titanium metallic films in an ethylene glycol + NH{sub 4}F based electrolyte. Nanoporous amorphous structures with 60–80 nm diameter and 2–4 μm length were formed on the surfaces of alumina substrates. The amorphous undoped and Al-doped TiO{sub 2} anodic oxides were heat-treated at different temperatures in the range of 280–720 °C for the investigation of their crystallization behavior. The combined effects of nanoporous structure and Al doping on crystallization behavior of titania were investigated using X-ray diffraction (XRD) and micro Raman analysis. The results indicated that both Al ions incorporated into the TiO{sub 2} structure and the nanoporous structure retarded the rutile formation. It was also revealed that presence or absence of metallic film underneath the nanopores has a major contribution to anatase-rutile transformation. - Highlights: • Al-doped TiO{sub 2} nanopores were grown on alumina substrates using anodization method. • The crystallization behavior of nanoporous Al-doped TiO{sub 2} were investigated. • Al doping into nanoporous TiO{sub 2} retarded the anatase-rutile transformation. • Nanostructuring has significant role in controlling rutile formation temperature. • The absence of the metallic film under the nanopores delayed the rutile formation.

  13. Interactions of aluminum with biochars and oxidized biochars: implications for the biochar aging process.

    Science.gov (United States)

    Qian, Linbo; Chen, Baoliang

    2014-01-15

    Interactions of aluminum with primary and oxidized biochars were compared to understand the changes in the adsorption properties of aged biochars. The structural characteristics of rice straw-derived biochars, before and after oxidation by HNO3/H2SO4, were analyzed by element composition, FTIR, and XPS. The adsorption of Al to primary biochars was dominated by binding to inorganic components (such as silicon particles) and surface complexation of oxygen-containing functional groups via esterification reactions. Oxidization (aging) introduced carboxylic functional groups on biochar surfaces, which served as additional binding sites for Al(3+). At pH 2.5-3.5, the Al(3+) binding was significantly greater on oxidized biochars than primary biochars. After loading with Al, the -COOH groups anchored to biochar surfaces were transformed into COO(-) groups, and the negative surface charge diminished, which indicated that Al(3+) coordinated with COO(-). Biochar is suggested as a potential adsorbent for removing Al from acidic soils. PMID:24364719

  14. The role of stress in self-ordered porous anodic oxide formation and corrosion of aluminum

    Science.gov (United States)

    Capraz, Omer Ozgur

    The phenomenon of plastic flow induced by electrochemical reactions near room temperature is significant in porous anodic oxide (PAO) films, charging of lithium batteries and stress-corrosion cracking (SCC). As this phenomenon is poorly understood, fundamental insight into flow from our work may provide useful information for these problems. In-situ monitoring of the stress state allows direct correlation between stress and the current or potential, thus providing fundamental insight into technologically important deformation and failure mechanisms induced by electrochemical reactions. A phase-shifting curvature interferometry was designed to investigate the stress generation mechanisms on different systems. Resolution of our curvature interferometry was found to be ten times more powerful than that obtained by state-of-art multiple deflectometry technique and the curvature interferometry helps to resolve the conflicting reports in the literature. During this work, formation of surface patterns during both aqueous corrosion of aluminum and formation of PAO films were investigated. Interestingly, for both cases, stress induced plastic flow controls the formation of surface patterns. Pore formation mechanisms during anodizing of the porous aluminum oxide films was investigated . PAO films are formed by the electrochemical oxidation of metals such as aluminum and titanium in a solution where oxide is moderately soluble. They have been used extensively to design numerous devices for optical, catalytic, and biological and energy related applications, due to their vertically aligned-geometry, high-specific surface area and tunable geometry by adjusting process variables. These structures have developed empirically, in the absence of understanding the process mechanism. Previous experimental studies of anodizing-induced stress have extensively focused on the measurement of average stress, however the measurement of stress evolution during anodizing does not provide

  15. Highly Ordered Zinc Oxide Nanotubules Synthesized within the Anodic Aluminum Oxide Template

    Institute of Scientific and Technical Information of China (English)

    WANG Zhen; LI HuLin

    2001-01-01

    @@ Zinc oxide (ZnO) is a wide-band-gap semiconductor, which has a broad range of applications, e.g., in pigment, rubber additives, gas sensors, varistors and transducers1. It has recently been demonstrated that nanophase zinc oxide can be used in photocells of the Gatzel type2, which results in improved current generation efficiency. The properties of high aspect ratios and small sizes of zinc oxide nanotubules or nanowires are expected to improve the luminescence efficiency of the electro-optical devices and the sensitivity of the chemical sensors3.

  16. Highly Ordered Zinc Oxide Nanotubules Synthesized within the Anodic Aluminum Oxide Template

    Institute of Scientific and Technical Information of China (English)

    WANG; Zhen

    2001-01-01

    Zinc oxide (ZnO) is a wide-band-gap semiconductor, which has a broad range of applications, e.g., in pigment, rubber additives, gas sensors, varistors and transducers1. It has recently been demonstrated that nanophase zinc oxide can be used in photocells of the Gatzel type2, which results in improved current generation efficiency. The properties of high aspect ratios and small sizes of zinc oxide nanotubules or nanowires are expected to improve the luminescence efficiency of the electro-optical devices and the sensitivity of the chemical sensors3.  ……

  17. Adhesion-enhanced thick copper film deposition on aluminum oxide by an ion-beam-mixed Al seed layer

    International Nuclear Information System (INIS)

    We report a highly-adherent 30-μm Cu conductive-path coating on an aluminum-oxide layer anodized on an aluminum-alloy substrate for a metal-printed circuit-board application. A 50-nm Al layer was first coated with an e-beam evaporative deposition method on the anodized oxide, followed by ion bombardment to mix the interfacial region. Subsequently, a Cu coating was deposited onto the mixed seed layer to the designed thickness. Adhesions of the interface were tested by using tape adhesion test, and pull-off tests and showed commercially acceptable adhesions for such thick coating layers. The ion beam mixing (IBM) plays the role of fastening the thin seed coating layer to the substrate and enhancing the adhesion of the Cu conductive path on the anodized aluminum surface.

  18. Doping optimization and surface modification of aluminum doped zinc oxide films as transparent conductive coating

    International Nuclear Information System (INIS)

    Aluminum doped zinc oxide (ZnO:Al) films were grown using spray pyrolysis technique. Effect of doping on structural, electrical, optical and morphological properties was studied. Aluminum doping improved the prominence of [002] growth while maintaining the grain size ∼ 48 nm. Using an intermediate Al/Zn atomic ratio in precursor (1.5:100), we could achieve a low resistivity ρ ∼ 7 × 10−4 Ωcm. These films possessed an average visible transmittance ∼ 88%, an optical gap ∼ 3.7 eV and plasma wavelength at 1.87 μm. A simultaneous use of methanol and iso-propanol in the precursor lead to a moderate surface roughness ∼ 12 nm. The films were surface modified using wet chemical etching in diluted hydrochloric acid, for varied time intervals (5 s–15 s) and etchant concentrations (0.125%–1%). The etching experiments could be used to know the building of the film as also to modify the surface for desired optical and morphological properties. - Highlights: ► High conductivity ZnO:Al films prepared by spray pyrolysis. ► Physical properties very competitive as transparent conductor. ► Co-use of methanol and iso-propanol made smoother but compact films. ► Wet chemical etching helped to modify the surface and understand the growth.

  19. Chemical Bath Deposition of Aluminum Oxide Buffer on Curved Surfaces for Growing Aligned Carbon Nanotube Arrays.

    Science.gov (United States)

    Wang, Haitao; Na, Chongzheng

    2015-07-01

    Direct growth of vertically aligned carbon nanotube (CNT) arrays on substrates requires the deposition of an aluminum oxide buffer (AOB) layer to prevent the diffusion and coalescence of catalyst nanoparticles. Although AOB layers can be readily created on flat substrates using a variety of physical and chemical methods, the preparation of AOB layers on substrates with highly curved surfaces remains challenging. Here, we report a new solution-based method for preparing uniform layers of AOB on highly curved surfaces by the chemical bath deposition of basic aluminum sulfate and annealing. We show that the thickness of AOB layer can be increased by extending the immersion time of a substrate in the chemical bath, following the classical Johnson-Mehl-Avrami-Kolmogorov crystallization kinetics. The increase of AOB thickness in turn leads to the increase of CNT length and the reduction of CNT curviness. Using this method, we have successfully synthesized dense aligned CNT arrays of micrometers in length on substrates with highly curved surfaces including glass fibers, stainless steel mesh, and porous ceramic foam. PMID:26053766

  20. Aluminum work function: Effect of oxidation, mechanical scraping and ion bombardment

    Science.gov (United States)

    Vinet, P.; Lemogne, T.; Montes, H.

    1985-01-01

    Surface studies have been performed on aluminum polycrystalline surfaces which have been mechanically scraped. Such studies were initiated in order to understand surface effects occurring in tribological processes which involve rubbing surfaces and the effects of adsorption of oxygen. To characterize the surfaces, the following three different experimental approaches have been used: (1) X.P.S. (X-ray photoelectron spectroscopy), in order to check the cleanliness of the surfaces and follow the adsorption and oxidation kinetics; (2) Analysis of the work function changes by following the energy spectra of secondary electrons emitted under low energy electron bombardment; and (3) Analysis of photoemission intensities under U.V. excitation. The reference state being chosen to be the surface cleaned by ion bombardment and exposures to oxygen atmospheres have been shown to lower the work function of clean polycrystalline aluminum by 1.2 eV. The oxygen pressure is found to affect only the kinetics of these experiments. Mechanical scraping has been shown to induce a decrease ( 0.3 eV) in the work function, which could sharply modify the kinetics of adsorption on the surface.

  1. Formation of unidirectional nanoporous structures in thickly anodized aluminum oxide layer

    Institute of Scientific and Technical Information of China (English)

    Hyun-Chae NA; Taek-Jin SUNG; Seok-Heon YOON; Seung-Kyoun HYUN; Mok-Soon KIM; Young-Gi LEE; Sang-Hyun SHIN; Seok-Moon CHOI; Sung YI

    2009-01-01

    A series of anodic aluminum oxide(AAO) was grown on the commercially pure 1050 aluminum sheet by controlling electrolyte temperature (2-15 ℃) and anodizing time (0.5-6 h), using a fixed applied current density of 3 A/dm2 in diluted sulfuric acid electrolyte. A crack-free thick AAO with the thickness of 105-120 ìm and containing unidirectional nano sized pores (average pore diameter of 5-7 nm) is successfully achieved in the specimens anodized for 2 h, irrespective of electrolyte temperature. When anodizing time reaches 6 h, very thick AAO with the thickness of 230-284 ìm is grown, and average diameter of unidirectional pores is in the range of 6-24 nm. The higher values in both the AAO thickness and pore diameter are attained for the specimens anodized at higher temperatures of 10-15 ℃. A crack is observed to exist in the AAO after anodizing up to 4 h and more. A higher fraction (more than 9%) of the crack is shown in the specimens anodized at higher temperatures of 10-15 ℃ for 6 h and a considerable amount of giant cracks are contained.

  2. Effects of Complex Structured Anodic Oxide Dielectric Layer Grown in Pore Matrix for Aluminum Capacitor.

    Science.gov (United States)

    Shin, Jin-Ha; Yun, Sook Young; Lee, Chang Hyoung; Park, Hwa-Sun; Suh, Su-Jeong

    2015-11-01

    Anodization of aluminum is generally divided up into two types of anodic aluminum oxide structures depending on electrolyte type. In this study, an anodization process was carried out in two steps to obtain high dielectric strength and break down voltage. In the first step, evaporated high purity Al on Si wafer was anodized in oxalic acidic aqueous solution at various times at a constant temperature of 5 degrees C. In the second step, citric acidic aqueous solution was used to obtain a thickly grown sub-barrier layer. During the second anodization process, the anodizing potential of various ranges was applied at room temperature. An increased thickness of the sub-barrier layer in the porous matrix was obtained according to the increment of the applied anodizing potential. The microstructures and the growth of the sub-barrier layer were then observed with an increasing anodizing potential of 40 to 300 V by using a scanning electron microscope (SEM). An impedance analyzer was used to observe the change of electrical properties, including the capacitance, dissipation factor, impedance, and equivalent series resistance (ESR) depending on the thickness increase of the sub-barrier layer. In addition, the breakdown voltage was measured. The results revealed that dielectric strength was improved with the increase of sub-barrier layer thickness. PMID:26726615

  3. In-Line Sputtered Gallium and Aluminum Codoped Zinc Oxide Films for Organic Solar Cells

    Directory of Open Access Journals (Sweden)

    Shang-Chou Chang

    2014-01-01

    Full Text Available Gallium and aluminum codoped zinc oxide (GAZO films were deposited at different temperatures by in-line sputtering. Aluminum is thermally unstable compared to other elements in GAZO films. The grains of GAZO films increase with deposition temperature. Coalescence between grains was observed for GAZO films deposited at 250°C. The deposition temperature exhibits positive influence on crystallinity, and electrical and optical properties of GAZO films. The carrier concentration and mobility of GAZO films increase, while the electrical resistivity of GAZO films decreases with deposition temperature. The average optical transmittance of GAZO films rises with deposition temperature. In-line sputtering demonstrates a potential method with simplicity, mass production, and large-area deposition to produce GAZO films with good electrical and optical quality. The electrical resistivity of 4.3 × 10−4 Ω cm and the average optical transmittance in the visible range from 400 to 800 nm of 92% can be obtained for GAZO films deposited at 250°C. The hybrid organic solar cells (OSC were fabricated on GAZO-coated glass substrates. Blended poly(3-hexylthiophene (P3HT and [6,6]-phenyl C61 butyric acid methyl ester (PCBM were the photoactive materials in OSC. The power conversion efficiency of OSC is 0.65% for the OSC with the 250°C deposited GAZO electrode.

  4. Effects of reducing solvent on copper, nickel, and aluminum joining using silver nanoparticles derived from a silver oxide paste

    International Nuclear Information System (INIS)

    The effects of reducing solvent on copper, nickel, and aluminum joining using silver nanoparticles derived from a silver oxide paste was investigated by thermal analysis, transmission electron microscopy (TEM) observation, and tensile shear testing. A complete weight loss of diethylene glycol (DEG) in a paste occurred during the redox reaction, whereas a polyethylene glycol 400 (PEG) paste retained the PEG solvent until about 300°C due to its longer carbon chains. Residual PEG in the paste reduced the natural oxide film on copper and nickel substrates during bonding, facilitating a direct sinter of silver nanoparticles to these substrates. On the other hand, silver nanoparticles were sintered to the natural oxide film on an aluminum substrate by the DEG paste. The suitability of the reducing solvent for oxide film reduction of the metal substrate during bonding was explained by an Ellingham diagram. (author)

  5. Copper-aluminum oxide catalysts for total oxidation of toluene synthesized by thermal decomposition of co-precipitated precursors

    International Nuclear Information System (INIS)

    Highlights: • Cu–Al oxides obtained by coprecipitation are active catalysts in toluene combustion. • Advantage of the catalyst is low copper content and alkali-free precipitating agent. • The stable oxide form built of CuO and CuAl2O4 is attained at 900 °C. • The optimum atomic Cu:Al ratio, ensuring maximum toluene conversion, is about 0.6. • The most active sample contains small CuO crystallites dispersed on the surface. - Abstract: Copper–aluminum containing precursors with various Cu/Al molar ratios (from 0.32–1.28) were prepared by co-precipitation in the presence of ammonium carbonate. The thermal stability of the obtained materials was investigated by thermal analysis, which revealed three crucial decomposition steps, finally resulting in the formation of mixed Cu–Al oxides. The changes in structure and texture of the samples at each decomposition step were examined by X-ray diffraction (XRD), diffuse reflectance UV–vis spectroscopy (UV–vis-DRS) and low temperature sorption of nitrogen. It was found that the entire removal of structural carbonates requires a calcination temperature as high as 900 °C. The samples after thermal treatment at this temperature varied in the phase composition of the bulk (determined by XRD) as well as of the surface (determined by X-ray photoelectron spectroscopy). All samples contained the CuAl2O4 phase. Furthermore, an increase in Cu content led to the appearance of an increasing amount of CuO. Copper oxide in the form of relatively small crystallites turned out to be the catalytically active phase in the total oxidation of toluene

  6. Copper-aluminum oxide catalysts for total oxidation of toluene synthesized by thermal decomposition of co-precipitated precursors

    Energy Technology Data Exchange (ETDEWEB)

    Białas, Anna [Faculty of Chemistry, Jagiellonian University, Ingardena 3, 30-060 Kraków (Poland); Kuśtrowski, Piotr, E-mail: kustrows@chemia.uj.edu.pl [Faculty of Chemistry, Jagiellonian University, Ingardena 3, 30-060 Kraków (Poland); Dudek, Barbara; Piwowarska, Zofia; Wach, Anna [Faculty of Chemistry, Jagiellonian University, Ingardena 3, 30-060 Kraków (Poland); Michalik, Marek [Institute of Geological Sciences, Jagiellonian University, Oleandry 2a, 30-063 Kraków (Poland); Kozak, Marek [Division of Petroleum Processing, Oil and Gas Institute, Łukasiewicza 1, 31-429 Kraków (Poland)

    2014-08-20

    Highlights: • Cu–Al oxides obtained by coprecipitation are active catalysts in toluene combustion. • Advantage of the catalyst is low copper content and alkali-free precipitating agent. • The stable oxide form built of CuO and CuAl{sub 2}O{sub 4} is attained at 900 °C. • The optimum atomic Cu:Al ratio, ensuring maximum toluene conversion, is about 0.6. • The most active sample contains small CuO crystallites dispersed on the surface. - Abstract: Copper–aluminum containing precursors with various Cu/Al molar ratios (from 0.32–1.28) were prepared by co-precipitation in the presence of ammonium carbonate. The thermal stability of the obtained materials was investigated by thermal analysis, which revealed three crucial decomposition steps, finally resulting in the formation of mixed Cu–Al oxides. The changes in structure and texture of the samples at each decomposition step were examined by X-ray diffraction (XRD), diffuse reflectance UV–vis spectroscopy (UV–vis-DRS) and low temperature sorption of nitrogen. It was found that the entire removal of structural carbonates requires a calcination temperature as high as 900 °C. The samples after thermal treatment at this temperature varied in the phase composition of the bulk (determined by XRD) as well as of the surface (determined by X-ray photoelectron spectroscopy). All samples contained the CuAl{sub 2}O{sub 4} phase. Furthermore, an increase in Cu content led to the appearance of an increasing amount of CuO. Copper oxide in the form of relatively small crystallites turned out to be the catalytically active phase in the total oxidation of toluene.

  7. Synthesis and properties of iridescent Zn-containing anodic aluminum oxide films

    International Nuclear Information System (INIS)

    A simple method of fabricating Zn-containing anodic aluminum oxide films for multifunctional anticounterfeit technology is reported. The resulting membranes were characterized with UV–vis illumination studies, natural light illumination color experiments, and electron microscopy analysis. Deposition of Zn in the nanopore region can enhance the color saturation of the thin alumina film with different colors dramatically. Both the anodization time and etching time have great influence on the structural color. The mechanisms for the emergence of this phenomenon are discussed and theoretical analysis further demonstrates the experimental results. - Highlights: • Iridescent PAA@Zn nanocomposite films were successfully fabricated. • A simple organics-assisted method is applied to making a series of fancy and multicolor patterns. • The color varies with the angle of incidence of the light used to view the film as is expected with Bragg–Snell formula. • Such colored films could be used in multifunctional anti-counterfeiting applications

  8. Photoluminescence and Raman studies in swift heavy ion irradiated polycrystalline aluminum oxide

    Indian Academy of Sciences (India)

    K R Nagabhushana; B N Lakshminarasappa; Fouran Singh

    2009-10-01

    Polycrystalline aluminum oxide is synthesized by combustion technique and XRD studies of the sample revealed the -phase. The synthesized sample is irradiated with 120 MeV swift Au9+ ions for the fluence in the range from 1 × 1011 to 1 × 1013 ions cm-2. A broad photoluminescence (PL) emission with peak at ∼447 nm and two sharp emissions with peak at ∼ 679 and ∼ 695 nm are observed in pristine when sample was excited with 326 nm. However, in the irradiated samples the PL intensity at ∼ 447, 679 and 695 nm decreases with increase in ion fluence. The -Al2O3 gives rise to seven Raman modes with Raman intensity with peaks at ∼ 253, 396, 417, 546, 630, 842, 867 cm-1 observed in pristine. The intensity of these modes decreases with increase in ion fluence. However, the Raman modes observed at lower fluences are found to disappear at higher fluence.

  9. Controllable synthesis of Ag nanorods using a porous anodic aluminum oxide template

    International Nuclear Information System (INIS)

    This paper describes a new approach to the synthesis of Ag nanorods. A solvothermal method was used to make Ag nanoparticles inside anodic aluminum oxide (AAO) templates. The nanoparticles were then annealed at 300 deg. C to produce Ag nanorods. The size of AAO templates, which is focused on in this study, would determine the diameter of Ag nanorods. The product was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). In this study, a nanorod growth mechanism is deduced, and understanding of the growth of nanorods inside AAO templates is furthered. This work demonstrates that it is possible to make crystalline nanorods that the size can be varied.

  10. Effect of intermetallic phases on the anodic oxidation and corrosion of 5A06 aluminum alloy

    Science.gov (United States)

    Li, Song-mei; Li, Ying-dong; Zhang, You; Liu, Jian-hua; Yu, Mei

    2015-02-01

    Intermetallic phases were found to influence the anodic oxidation and corrosion behavior of 5A06 aluminum alloy. Scattered intermetallic particles were examined by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) after pretreatment. The anodic film was investigated by transmission electron microscopy (TEM), and its corrosion resistance was analyzed by electrochemical impedance spectroscopy (EIS) and Tafel polarization in NaCl solution. The results show that the size of Al-Fe-Mg-Mn particles gradually decreases with the iron content. During anodizing, these intermetallic particles are gradually dissolved, leading to the complex porosity in the anodic film beneath the particles. After anodizing, the residual particles are mainly silicon-containing phases, which are embedded in the anodic film. Electrochemical measurements indicate that the porous anodic film layer is easily penetrated, and the barrier plays a dominant role in the overall protection. Meanwhile, self-healing behavior is observed during the long immersion time.

  11. Tribological Influence of Kinematic Oil Viscosity Impregnated in Nano pores of Anodic Aluminum Oxide Film

    International Nuclear Information System (INIS)

    The friction behavior of a 60-μm-thick anodic aluminum oxide (AEU) film having cylindrical nano pores of 45-nm diameter was investigated as a function of impregnated oil viscosity ranging from 3.4 to 392.6 CT. Reciprocating ball-on-flat sliding friction tests using a 1-mm-diameter steel ball as the counterpart were carried out with normal load ranging from 0.1 to 1 N in an ambient environment. The friction coefficient significantly decreased with an increase in the oil viscosity. The boundary lubrication film remained effectively under all test conditions when high-viscosity oil was impregnated, whereas it was easily destroyed when low-viscosity oil was impregnated. Thin plastic deformed layer patches were formed on the worn surface with high-viscosity oil without evidence of thromboembolic reaction and transfer of counterpart material

  12. Synthesis of silicon nanotubes with cobalt silicide ends using anodized aluminum oxide template

    International Nuclear Information System (INIS)

    Silicon nanotubes (SiNTs) are compatible with Si-based semiconductor technology. In particular, the small diameters and controllable structure of such nanotubes are remaining challenges. Here we describe a method to fabricate SiNTs intrinsically connected with cobalt silicide ends based on highly ordered anodic aluminum oxide (AAO) templates. Size and growth direction of the SiNTs can be well controlled via the templates. The growth of SiNTs is catalyzed by the Co nanoparticles reduced on the pore walls of the AAO after annealing, with a controllable thickness at a given growth temperature and time. Simultaneously, cobalt silicide forms on the bottom side of the SiNTs.

  13. Nanoporous anodized aluminum oxide-coated polycarbonate surface: Tailoring of transmittance and reflection properties

    International Nuclear Information System (INIS)

    Nanostructured coatings increase the transmittance and decrease the reflection of polycarbonate (PC). In this work, nanoporous anodized aluminum oxide (AAO) coating was formed electrochemically on a PC surface. The reflection properties of the AAO-coated PC were modified by varying the thickness of the AAO layer, the anodization parameters, and the pore size of AAO. Transmittance and reflection were measured by ellipsometry. The optical transmittance of the AAO film on PC was 86-94% in the wavelength range 420-780 nm, which was about four percentage units higher than the transmittance of uncoated PC. The minimum reflection of 0.2% was observed for PC with an AAO coating of 177 nm. The reflection was about five percentage units less than the corresponding value for uncoated polycarbonate. Nanoporous surfaces and profiles of AAO were characterized by Scanning Electron Microscope

  14. Screen Cage Ion Plating (SCIP) and scratch testing of polycrystalline aluminum oxide

    Science.gov (United States)

    Spalvins, Talivaldis; Sliney, Harold E.; Deadmore, Daniel L.

    1992-01-01

    A screen cage ion plating (SCIP) technique was developed to apply silver films on electrically nonconducting aluminum oxide. It is shown that SCIP has remarkable throwing power; surfaces to be coated need not be in direct line of sight with the evaporation source. Scratch tests, employing a diamond stylus with a 200 micro m radius tip, were performed on uncoated and on silver coated alumina. Subsequent surface analysis show that a significant amount of silver remains on the scratched surfaces, even in areas where high stylus load produced severe crack patterns in the ceramic. Friction coefficients were lowered during the scratch tests on the coated alumina indicating that this modification of the ion planting process should be useful for applying lubricating films of soft metals to electrical insulating materials. The very good throwing power of SCIP also strongly suggests general applicability of this process in other areas of technology, e.g., electronics, in addition to tribology.

  15. Studies of aluminum oxide thin films deposited by laser ablation technique

    Science.gov (United States)

    Płóciennik, P.; Guichaoua, D.; Korcala, A.; Zawadzka, A.

    2016-06-01

    This paper presents the structural and optical investigations of the aluminum oxide nanocrystalline thin films. Investigated films were fabricated by laser ablation technique in high vacuum onto quartz substrates. The films were deposited at two different temperatures of the substrates equal to room temperature and 900 K. X-ray Diffraction spectra proved nanocrystalline character and the corundum phase of the film regardless on the substrate temperature during the deposition process. Values of the refractive indices, extinction and absorption coefficients were calculated by using Transmission and Reflection Spectroscopy in the UV-VIS-NIR range of the wavelength. Coupling Prism Method was used for films thickness estimations. Experimental measurements and theoretical calculations of the Third Harmonic Generation were also reported. Obtained results show that the lattice strain may affect obtained values of the third order nonlinear optical susceptibility.

  16. Nanoporous anodized aluminum oxide-coated polycarbonate surface: Tailoring of transmittance and reflection properties

    Energy Technology Data Exchange (ETDEWEB)

    Saarikoski, Inka; Suvanto, Mika [Department of Chemistry, University of Joensuu, P.O. Box 111, FI-80101 Joensuu (Finland); Pakkanen, Tapani A. [Department of Chemistry, University of Joensuu, P.O. Box 111, FI-80101 Joensuu (Finland)], E-mail: Tapani.Pakkanen@joensuu.fi

    2008-10-01

    Nanostructured coatings increase the transmittance and decrease the reflection of polycarbonate (PC). In this work, nanoporous anodized aluminum oxide (AAO) coating was formed electrochemically on a PC surface. The reflection properties of the AAO-coated PC were modified by varying the thickness of the AAO layer, the anodization parameters, and the pore size of AAO. Transmittance and reflection were measured by ellipsometry. The optical transmittance of the AAO film on PC was 86-94% in the wavelength range 420-780 nm, which was about four percentage units higher than the transmittance of uncoated PC. The minimum reflection of 0.2% was observed for PC with an AAO coating of 177 nm. The reflection was about five percentage units less than the corresponding value for uncoated polycarbonate. Nanoporous surfaces and profiles of AAO were characterized by Scanning Electron Microscope.

  17. Graphene-Assisted Chemical Etching of Silicon Using Anodic Aluminum Oxides as Patterning Templates.

    Science.gov (United States)

    Kim, Jungkil; Lee, Dae Hun; Kim, Ju Hwan; Choi, Suk-Ho

    2015-11-01

    We first report graphene-assisted chemical etching (GaCE) of silicon by using patterned graphene as an etching catalyst. Chemical-vapor-deposition-grown graphene transferred on a silicon substrate is patterned to a mesh with nanohole arrays by oxygen plasma etching using an anodic- aluminum-oxide etching mask. The prepared graphene mesh/silicon is immersed in a mixture solution of hydrofluoric acid and hydro peroxide with various molecular fractions at optimized temperatures. The silicon underneath graphene mesh is then selectively etched to form aligned nanopillar arrays. The morphology of the nanostructured silicon can be controlled to be smooth or porous depending on the etching conditions. The experimental results are systematically discussed based on possible mechanisms for GaCE of Si. PMID:26473800

  18. Microstructures and Composition of Ceramic Coatings on Aluminum Produced by Micro-Arc Oxidation

    Institute of Scientific and Technical Information of China (English)

    SHEN De-jiu; WANG Yu-lin; GU Wei-chao; XING Guang-zhong

    2004-01-01

    Microstructures and phase composition of the ceramic coatings formed on pure aluminum by heteropolar pulsed current ceramic synthesizing system for different periods were investigated by X-ray diffraction (XRD) and scanning electronic microscopy (SEM). Results show that the amount of the discharge channels in the ceramic coating sminish while the aperture largen in the micro-arc oxidation process, and the surface of the ceramic coatingmelted and solidified in the process.XRD studies of ceramic coatings deposited for different time show that these coatings consist mainly of α-Al2 O3, γ-Al2 O3 , θ-Al2 O3 and a little amorphous phase, and phase composition of compact and porous ceramic coatings don' t have much difference but have a little change of the content of α-Al2 O3 and amorphous phase.

  19. Synthesis of ordered Sinanowire arrays in porous anodic aluminum oxide templates

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Highly ordered polycrystalline Si nanowire arrays were synthesized in porous anodic aluminum oxide (AAO) templates by the chemical vapor deposition (CVD)method. The morphological structure, the crystal character of Si nanowire arrays and the individual nanowire were analyzed by the transmission electron microscopy (TEM),scanning electron microscopy (SEM), atom force microscopy (AFM) and the X-ray diffraction spectrum (XRD), respectively. It is shown that most fabricated silicon nanowires (SiNWs) tend to be assembled parallelly in bundles and constructed with highly orientated arrays. This method provides a simple and low cost fabricating craftwork and the diameters and lengths of SiNWs can be controlled, the large area Si nanowire arrays can be achieved easily under such a way.The curling and twisting SiNWs are fewer than those by other synthesis methods.

  20. Quench of molten aluminum oxide associated with in-vessel debris retention by RPV internal water

    International Nuclear Information System (INIS)

    In-vessel debris coolability experiments were performed in ALPHA program at JAERI. Molten aluminum oxide (Al2O3) was poured into a pool of water in a lower head experimental vessel. Post-test observation and measurement using an ultrasonic technique indicated the formation of the interfacial gap between the solidified Al2O3 and the vessel wall. Thermal responses of the vessel wall implied that the interfacial gap acted initially as a thermal resistance and water subsequently penetrated into the interfacial gap. The maximum heat flux at the inner surface of the vessel facing to the solidified Al2O3 was roughly evaluated to be ranged from 320 kW/m2 to 600 kW/m2. A post-test analysis was conducted with CAMP code. The influence of the interfacial gap on thermal behavior of Al2O3 and the vessel wall was examined. (authors)

  1. Hydrogenation of Levulinic Acid over Nickel Catalysts Supported on Aluminum Oxide to Prepare γ-Valerolactone

    Directory of Open Access Journals (Sweden)

    Jie Fu

    2015-12-01

    Full Text Available Four types of nickel catalysts supported on aluminum oxide (Ni/Al2O3 with different nickel loadings were synthesized using the co-precipitation method and were used for the hydrogenation of levulinic acid (LA to prepare γ-valerolactone (GVL. The synthesized Ni/Al2O3 catalysts exhibited excellent catalytic activity in dioxane, and the activity of the catalysts was excellent even after being used four times in dioxane. The catalytic activity in dioxane as a solvent was found to be superior to the activity in water. Nitrogen physisorption, X-ray diffraction, and transmission electron microscopy were employed to characterize the fresh and used catalysts. The effects of the nickel loading, temperature, hydrogen pressure, and substrate/catalyst ratio on the catalytic activity were investigated.

  2. Characterization of Anodic Aluminum Oxide Membrane with Variation of Crystallizing Temperature for pH Sensor.

    Science.gov (United States)

    Yeo, Jin-Ho; Lee, Sung-Gap; Jo, Ye-Won; Jung, Hye-Rin

    2015-11-01

    We fabricated electrolyte-dielectric-metal (EDM) device incorporating a high-k Al2O3 sensing membrane from a porous anodic aluminum oxide (AAO) using a two step anodizing process for pH sensors. In order to change the properties of the AAO template, the crystallizing temperature was varied from 400 degrees C to 700 degrees C over 2 hours. The structural properties were observed by field emission scanning electron microscopy (FE-SEM). The pH sensitivity increased with an increase in the crystallizing temperature from 400 degrees C to 600 degrees C. However at 700 degrees C, deformation occurred. The porous AAO sensor with a crystallizing temperature of 600 degrees C displayed the good sensitivity and long-term stability and the values were 55.7 mV/pH and 0.16 mV/h, respectively. PMID:26726567

  3. An anode with aluminum doped on zinc oxide thin films for organic light emitting devices

    International Nuclear Information System (INIS)

    Doped zinc oxides are attractive alternative materials as transparent conducting electrode because they are nontoxic and inexpensive compared with indium tin oxide (ITO). Transparent conducting aluminum-doped zinc oxide (AZO) thin films have been deposited on glass substrates by DC reactive magnetron sputtering method. Films were deposited at a substrate temperature of 150-bar oC in 0.03 Pa of oxygen pressure. The electrical and optical properties of the film with the Al-doping amount of 2 wt% in the target were investigated. For the 300-nm thick AZO film deposited using a ZnO target with an Al content of 2 wt%, the lowest electrical resistivity was 4x10-4Ωcm and the average transmission in the visible range 400-700 nm was more than 90%. The AZO film was used as an anode contact to fabricate organic light-emitting diodes. The device performance was measured and the current efficiency of 2.9 cd/A was measured at a current density of 100 mA/cm2

  4. Microstructural Effects on the Reactivity of Nano-Aluminum/Iodine (V) Oxide Films

    Science.gov (United States)

    Little, Brian; Langhals, Jarred; Emery, Sam; Martinez, Lucas; Welle, Eric; Lindsay, Michael

    2015-06-01

    Recent efforts investigating the self-ignition mechanism of nanoaluminum blended with iodine (V) oxide in the form of powders with and without additives suggests that ignition begins below the decomposition point of either reactant and takes place at the alumina shell surrounding the aluminum nanoparticle. As observed in previous studies of powder composites, microstructural features such as particle morphology are expected to strongly influence properties that govern the combustion behavior of this energetic material (EM). In this study, highly reactive composites containing amorphous and/or crystalline iodine oxide and nano-sized Al was blended with an additive and deposited as films. Physiochemical techniques such as thermal gravimetric analysis, scanning calorimetry, X-ray diffraction, electron microscopy, high-speed imaging, time of arrival data via photodiodes and planar doppler velocimetry were employed to characterize these EMs with emphasis on correlating the reaction rate (burn rate) with inherent microstructural features (porosity, thickness, TMD, etc). This work was a continuation of efforts to probe the self-ignition mechanism of Al-iodine (V) oxide composites.

  5. Oxidation Phase Diagram of Small Aluminum Clusters Based on First-Principles Calculations

    Science.gov (United States)

    Wang, Ligen; Kuklja, Maija

    2009-06-01

    It is important to understand the properties of individual nanometals before we can exploit their efficiency as energetic materials or as enhancement additives to other energetic formulations. In this paper, we construct the (p, T) phase diagram for the O/Al13 system based on first-principles atomistic thermodynamics. The temperature and pressure is taken into account via the oxygen chemical potential. The optimized Al13 cluster has an icosahedral shape. We find that O adsorption on the Al13 surface is site-specific; in particular, O adsorption at the bridge sites is most stable, whereas adsorption at the hollow sites is slightly unfavorable. For various oxygen adsorption layers, we determine the adsorption configurations/patterns by performing Monte Carlo calculations. We assume that the metal cluster becomes completely oxidized and calculate formation enthalpies of various oxidized metal clusters. The obtained phase diagram shows that an intact Al13 cluster is stable at the low O chemical potential range and the fully oxidized metal cluster is stable at the high O chemical potential range. However, the O adsorption phases are never thermodynamically stable. This study provides important insights into basic behavior of small aluminum clusters in the presence of oxygen, and may affect reliable predictions of behavior of Al-high explosive composites.

  6. Sediment toxicity and bioaccumulation of nano and micron-sized aluminum oxide.

    Science.gov (United States)

    Stanley, Jacob K; Coleman, Jessica G; Weiss, Charles A; Steevens, Jeffery A

    2010-02-01

    Nano-aluminum oxide (Al(2)O(3)) is used commercially in coatings and abrasives. Nano-Al(2)O(3) can also be generated through the oxidation of nano-aluminum in military propellants and energetics. The purpose of the present study was to assess toxicity and bioaccumulation of nano-Al(2)O(3) to a variety of sediment organisms (Tubifex tubifex, Hyalella azteca, Lumbriculus variegatus, and Corbicula fluminea). The bioaccumulation and toxicity of nano-Al(2)O(3) was compared with that of micron-sized Al(2)O(3) to investigate potential size-related effects. Results of the present study show species-specific differences in relative bioaccumulation of nano and micron-sized Al(2)O(3). Significant toxic effects (survival and growth) were observed in H. azteca testing, but only at high concentrations unlikely to be found in the environment. Nano-Al(2)O(3) was found to be more toxic than micron-sized Al(2)O(3) to H. azteca survival in a 14-d study in which organisms were in direct contact with a thin layer of 625 or 2,500 mg of Al(2)O(3) dispersed on the surface of either sediment or sand. A significant growth effect was also observed for nano but not micron-sized Al(2)O(3) at the highest treatment level tested (100 g/kg Al(2)O(3)) in a 10-d H. azteca bioassay in which Al(2)O(3) was homogenized with sediment. However, differences in measured sediment Al concentrations (micron-sized = 55.1 [+/-0.6] g/kg Al; nano-sized = 66.2 [+/-0.6] g/kg Al) in the nano and micron-sized Al(2)O(3) preclude direct comparison of the toxicity of these two treatments based on particle size. PMID:20821462

  7. Oxide and proton conductivity in aluminum-doped tricalcium oxy-silicate

    Energy Technology Data Exchange (ETDEWEB)

    Porras-Vazquez, J.M.; De la Torre, A.G.; Losilla, E.R.; Aranda, M.A.G. [Dept. Quimica Inorganica, Cristalografia y Mineralogia, Universidad de Malaga, Campus Teatinos, 29071-Malaga (Spain)

    2007-06-15

    Aluminum doping in tricalcium silicate, Ca{sub 3}(SiO{sub 4})O, has been studied by high-resolution laboratory X-ray powder diffraction and the Rietveld method. Two nominal series have been designed and studied. Oxygen-fixed Ca{sub 3-x/2}Al{sub x/2}(Si{sub 1-x/2}Al{sub x/2}O{sub 4})O series has been prepared as single-phase up to x = 0.03. However, oxygen-variable Ca{sub 3}(Si{sub 1-x}Al{sub x}O{sub 4})O{sub 1-x/2}{open_square}{sub x/2} series has not been stabilized for any composition. The samples show oxide anion conductivity with a small p-type electronic contribution under oxidizing conditions. Typical total conductivities for these solids are 10{sup -} {sup 5}-10{sup -} {sup 4}S cm{sup -} {sup 1} at 1100 K. The oxide ion transference numbers are very high, {proportional_to} 0.98, under reducing conditions, i.e. dry 5%H{sub 2}-N{sub 2}/air gradient. The oxide ion transference numbers are slightly lower, {proportional_to} 0.91 under oxidizing conditions, i.e. dry O{sub 2}/air gradient. These compounds display a very important proton contribution to the overall conductivities under humidified atmospheres. The proton transference number ranges between 0.72 and 0.55 at 873 and 1023 K, respectively. (author)

  8. Functionalizing Aluminum Oxide by Ag Dendrite Deposition at the Anode during Simultaneous Electrochemical Oxidation of Al.

    Science.gov (United States)

    Rafailović, Lidija D; Gammer, Christoph; Rentenberger, Christian; Trišović, Tomislav; Kleber, Christoph; Karnthaler, Hans Peter

    2015-11-01

    A novel synthesis strategy is presented for depositing metallic Ag at the anode during simultaneous electrochemical oxidation of Al. This unexpected result is achieved based on galvanic coupling. Metallic dendritic nanostructures well-anchored in a high surface area supporting matrix are envisioned to open up a new avenue of applications. PMID:26398487

  9. Effect of Aluminum concentration on structural and optical properties of DC reactive magnetron sputtered Zinc Aluminum Oxide thin films for transparent electrode applications

    International Nuclear Information System (INIS)

    Zinc Aluminum Oxide(ZAO) thin films were deposited on glass substrates by DC reactive magnetron sputtering in an Ar+O2 gas mixture using commercial available Zn metal (99.99% purity) and Al (99.99% purity) targets of 2 inch diameter and 4 mm thickness. The films were characterized and the effect of aluminum (Al) concentration (2 at %-6 at %) on the structural and optical properties was studied. The average crystallite size obtained from Scherer formula is in the range of 32-44nm. Microstructural analysis using Scanning Electron Microscope (SEM) supplemented with EDS is carried out to find the grain size as well as to find the composition elemental data of prepared thin films. Optical study is performed to calculate the extinction coefficient (k), absorption coefficient (a), optical band gap (Eg) using transmission spectra obtained using UV-VIS-NIR spectrophotometer. There was widening of optical band gap with increasing aluminum concentration. ZAO film with low resistivity 3.2 × 10−4 cm and high transmittance of 80% is obtained for 3at% doped Al which is crucial for optoelectronic applications.

  10. Analysis of multilayered, nitrogen-doped aluminum oxide and hafnium oxide dielectric films for wide-temperature capacitor applications

    International Nuclear Information System (INIS)

    Capacitors with stable dielectric properties across a wide temperature range are a vital component in many power conditioning applications. High breakdown strength and low loss are also important for many applications. In this study, the dielectric properties of multilayer nitrogen-doped aluminum oxide and hafnium oxide films were characterized, comparing their properties to single layer films. The films were found to be stable from − 50 to 200 °C and from 20 Hz to 1 MHz. An order of magnitude decrease in leakage current was observed for the bilayer films. Breakdown strength for the multilayer films increased up to 75%. This concurs with the hypothesis that the addition of dielectric interfaces provides area to trap and dissipate runaway charge moving through the dielectric, thus lowering leakage current and increasing the breakdown strength. - Highlights: • Multilayer dielectric had stable dielectric properties for a wide temperature range. • Leakage current decreased an order of magnitude with layered dielectrics. • Breakdown strength increase of up to 75% was observed with layered dielectrics

  11. Effect of Holding Time Before Solidification on Double-Oxide Film Defects and Mechanical Properties of Aluminum Alloys

    Science.gov (United States)

    El-Sayed, Mahmoud Ahmed; Salem, Hanadi A. G.; Kandeil, Abdelrazek Youssef; Griffiths, W. D.

    2011-12-01

    Double-oxide films (bifilms) have been held responsible for the variability in mechanical properties of aluminum castings. It has been suggested that the air entrapped inside a bifilm can react with the surrounding melt, leading to its consumption, which might improve the mechanical properties of the castings. In this work the effect of holding the melt before solidification on the distribution of mechanical properties, and by implication on entrained double oxide films, was investigated for several different aluminum alloys. The Weibull moduli of plate castings were determined under tensile conditions, and their fracture surfaces were examined for evidence of oxide films. The results suggested the occurrence of two competing mechanisms during the holding treatment: (1) the consumption of air inside the bifilms by reaction with the surrounding molten metal that may lead to improvements in mechanical properties and (2) the accompanying diffusion of hydrogen into the bifilms, which would be expected to have a deleterious effect on properties.

  12. Behavior of aluminum oxide, intermetallics and voids in Cu-Al wire bonds

    International Nuclear Information System (INIS)

    Nanoscale interfacial evolution in Cu-Al wire bonds during isothermal annealing from 175 deg. C to 250 deg. C was investigated by high resolution transmission electron microscopy (HRTEM). The native aluminum oxide film (∼5 nm thick) of the Al pad migrates towards the Cu ball during annealing. The formation of intermetallic compounds (IMC) is controlled by Cu diffusion, where the kinetics obey a parabolic growth law until complete consumption of the Al pad. The activation energies to initiate crystallization of CuAl2 and Cu9Al4 are 60.66 kJ mol-1 and 75.61 kJ mol-1, respectively. During IMC development, Cu9Al4 emerges as a second layer and grows together with the initial CuAl2. When Al is completely consumed, CuAl2 transforms to Cu9Al4, which is the terminal product. Unlike the excessive void growth in Au-Al bonds, only a few voids nucleate in Cu-Al bonds after long-term annealing at high temperatures (e.g., 250 oC for 25 h), and their diameters are usually in the range of tens of nanometers. This is due to the lower oxidation rate and volumetric shrinkage of Cu-Al IMC compared with Au-Al IMC.

  13. Tailoring defect structure and optical absorption of porous anodic aluminum oxide membranes

    International Nuclear Information System (INIS)

    Defects influence the optical and electronic properties of nanostructured materials that may be relevant for applications. In self-organized anodic aluminum oxide (AAO) templates we have investigated the effect of annealing, doping and nanoscale metal deposition. Optical absorption spectroscopy has been used as a sensitive probe for the defect density in AAO templates. The electronic spectra are found to be dominated by bands which originate from oxygen-deficient color centers (F+, F and F2). In annealing studies, the integrated absorption of the bands changes non-monotonically with annealing temperature and annealing time. This demonstrates that the concentration of defects can be optimized to tailor the optical properties of the AAO. Metallic Au wires are deposited in the template to establish a plasmonic template or array. The investigations provide an interesting insight into the interplay of reactivity and diffusivity on nanoscales. - Highlights: ► Preparation of metal wire arrays in oxide templates with tailored plasmonic properties. ► Oxygen defects are characterized using optical absorption and fluorescence. ► Optical absorption spectra are assigned to energy levels of oxygen vacancies (color centers). ► Annealing and electrodeposition of Au wires minimize defects maintaining the morphology.

  14. Aluminum-induced oxidative stress and neurotoxicity in grass carp (Cyprinidae--Ctenopharingodon idella).

    Science.gov (United States)

    Fernández-Dávila, María Lourdes; Razo-Estrada, Amparo Celene; García-Medina, Sandra; Gómez-Oliván, Leobardo Manuel; Piñón-López, Manuel Jesús; Ibarra, Rocio Guzmán; Galar-Martínez, Marcela

    2012-02-01

    Aluminum is used in a large number of anthropogenic processes, leading to aquatic ecosystems pollution. Diverse studies show that in mammals this metal may produce oxidative stress, is neurotoxic, and is involved in the development of neurodegenerative disorders, such as Alzhaimer's and Parkinson's diseases. Nevertheless, there are only few studies with respect to Al-induced neurotoxicity on aquatic fauna, particularly on fishes of economical interest, such as the grass carp (Ctenopharingodon idella). This study evaluates Al-induced toxicity on the grass carp C. idella. Specimens were exposed to the maximum concentration allowed in order to protect aquatic life (0.1 mg L⁻¹), for 12, 24, 48, 72 and 96 h. After the exposure time, lipid peroxidation degree, superoxide dismutase and catalase activity, as well as dopamine, adrenaline and noradrenaline levels were evaluated. Al concentration in organisms and water was also measured, in order to determine the bioconcentration factor. Results show that Al bioconcentrates in grass carp inducing oxidative stress (increment of 300 and 455 percent on lipid peroxidation degree and SOD activity, and decrement of 49 percent on CAT activity) and neurotoxicity (increment of 55 and 155 percent on dopamine and adrenaline levels and decrement of 93 percent on noradrenaline level). PMID:21993346

  15. Impact of water corrosion on nanoscale conductance on aluminum doped zinc oxide

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jong-Hun; Lee, Hyunsoo; Choi, Sunghyun [Graduate School of EEWS (WCU) and Nanocentury KI, KAIST, Daejeon, 305-701 (Korea, Republic of); Center for Nanomaterials and Chemical Reactions, Institute for Basic Science, Daejeon, 305-701 (Korea, Republic of); Bae, Kyoung Hwan [The Thin Film Coating Team, KCC Corporation, Marbook Dong 83, Ki-Heung Gu, Yong-In City, 459-708 (Korea, Republic of); Park, Jeong Young, E-mail: jeongypark@kaist.ac.kr [Graduate School of EEWS (WCU) and Nanocentury KI, KAIST, Daejeon, 305-701 (Korea, Republic of)

    2013-11-29

    One major cause of failure in solar cell modules is associated with the degradation of conductive layers by the ingress of water. In this study, the corrosive interactions between water and transparent conducting oxides, including aluminum-doped ZnO (AZO) and indium tin oxide (ITO), were studied. The AZO layer exhibited ∼ 90% increase in sheet resistance from 17.5 to 33 ohm/square after an accelerated moisture test where the samples were stored at 80 °C and 100% humidity, while the conductivity of the ITO layer remained essentially unchanged. In order to elucidate the water-induced degradation mechanism of AZO, the structure and composition were characterized with conductive atomic force microscopy, energy dispersive spectrometry (EDS), and X-ray photoelectron spectroscopy (XPS) before and after the moisture test. It was found that the grain boundary of AZO exhibits a higher local conductance compared to that in the middle of the grain. A decrease in local conductance at the grain boundary after the moisture test was observed, which is attributed to depletion of the Zn, based on XPS and EDS analyses. - Highlights: • The moisture treatment lowers the local conductance of Al-doped ZnO (AZO). • Conductive atomic force microscopy shows the nanoelectronic properties of AZO. • Locally conductive areas are distributed along the grain boundaries. • The ratio of Zn to O along the grain boundaries was higher than that inside the grain.

  16. Evaluation of cerium oxide coated Cu cermets as inert anodes for aluminum electrowinning

    Energy Technology Data Exchange (ETDEWEB)

    1992-08-01

    Cu/NiFe{sub 2}O{sub 4} cermets were evaluated, with and without an in-situ deposited CEROX (TM; cerium oxide) coating, in 100 h laboratory A1 electrowinning tests. Bath ratio and current density were varied between tests and corrosion was determined by contamination of the aluminum and cryolite by cermet components (Cu, Fe, and Ni). Higher bath ratios of 1.5 to 1.6 led to less corrosion and thicker CEROX coatings. Lower current densities led to slightly less corrosion but much less oxidation of the Cu cermet substrate. At identical test conditions, the corrosion of the CEROX coated cermets was 1/7 that of an uncoated cermet. Corrosion was increased in CEROX coated cermets tested under unsaturated alumina conditions. The electrical conductivity of the CEROX coating was measured to be {approximately}0.2 ohm{sup {minus}1}cm{sup {minus}1}, resulting in a slight voltage penalty, depending on the thickness of the coating.

  17. Application of a palladium hexacyanoferrate film-modified aluminum electrode to electrocatalytic oxidation of hydrazine.

    Science.gov (United States)

    Razmi, Habib; Azadbakht, Azadeh; Sadr, Moayad Hossaini

    2005-11-01

    A palladium hexacyanoferrate (PdHCF) film as an electrocatalytic material was obtained at an aluminum (Al) electrode by a simple electroless dipping method. The modified Al electrode demonstrated a well-behaved redox couple due to the redox reaction of the PdHCF film. The PdHCF film showed an excellent electrocatalytic activity toward the oxidation of hydrazine. The electrocatalytic oxidation of hydrazine was studied by cyclic voltammetry and rotating disk electrode voltammetry techniques. A calibration graph obtained for the hydrazine consisted of two segments (localized at concentration ranges 0.39-10 and 20-75 mM). The rate constant k and transfer coefficient alpha for the catalytic reaction and the diffusion coefficient of hydrazine in the solution D, were found to be 3.11 x 10(3) M(-1) s(-1), 0.52 and 8.03 x 10(-6) cm2 s(-1) respectively. The modified electrode was used to amperometric determination of hydrazine in photographic developer. The interference of ascorbic acid and thiosulfate were investigated and greatly reduced using a thin film of Nafion on the modified electrode. The modified electrode indicated reproducible behavior and a high level of stability during electrochemical experiments, making it particularly suitable for analytical purposes. PMID:16317900

  18. Behavior of aluminum oxide, intermetallics and voids in Cu-Al wire bonds

    Energy Technology Data Exchange (ETDEWEB)

    Xu, H., E-mail: HXu14@bama.ua.edu [Department of Metallurgical and Materials Engineering, The University of Alabama, Tuscaloosa, AL 35487 (United States); Liu, C.; Silberschmidt, V.V. [Wolfson School of Mechanical and Manufacturing Engineering, Loughborough University, Loughborough LE11 3TU (United Kingdom); Pramana, S.S. [School of Materials Science and Engineering, Nanyang Technological University, Nanyang Avenue, Singapore 639798 (Singapore); White, T.J. [School of Materials Science and Engineering, Nanyang Technological University, Nanyang Avenue, Singapore 639798 (Singapore); Centre for Advanced Microscopy, Australian National University, Canberra, ACT 2601 (Australia); Chen, Z. [School of Materials Science and Engineering, Nanyang Technological University, Nanyang Avenue, Singapore 639798 (Singapore); Acoff, V.L. [Department of Metallurgical and Materials Engineering, The University of Alabama, Tuscaloosa, AL 35487 (United States)

    2011-08-15

    Nanoscale interfacial evolution in Cu-Al wire bonds during isothermal annealing from 175 deg. C to 250 deg. C was investigated by high resolution transmission electron microscopy (HRTEM). The native aluminum oxide film ({approx}5 nm thick) of the Al pad migrates towards the Cu ball during annealing. The formation of intermetallic compounds (IMC) is controlled by Cu diffusion, where the kinetics obey a parabolic growth law until complete consumption of the Al pad. The activation energies to initiate crystallization of CuAl{sub 2} and Cu{sub 9}Al{sub 4} are 60.66 kJ mol{sup -1} and 75.61 kJ mol{sup -1}, respectively. During IMC development, Cu{sub 9}Al{sub 4} emerges as a second layer and grows together with the initial CuAl{sub 2}. When Al is completely consumed, CuAl{sub 2} transforms to Cu{sub 9}Al{sub 4}, which is the terminal product. Unlike the excessive void growth in Au-Al bonds, only a few voids nucleate in Cu-Al bonds after long-term annealing at high temperatures (e.g., 250 {sup o}C for 25 h), and their diameters are usually in the range of tens of nanometers. This is due to the lower oxidation rate and volumetric shrinkage of Cu-Al IMC compared with Au-Al IMC.

  19. Silicon effects on formation of EPO oxide coatings on aluminum alloys

    Energy Technology Data Exchange (ETDEWEB)

    Wang, L. [Department of Mechanical, Automotive and Materials Engineering, University of Windsor, Windsor, ON, N9B 3P4 (Canada); Nie, X. [Department of Mechanical, Automotive and Materials Engineering, University of Windsor, Windsor, ON, N9B 3P4 (Canada)]. E-mail: xnie@uwindsor.ca

    2006-01-03

    Electrolytic plasma processes (EPP) can be used for cleaning, metal-coating, carburizing, nitriding, and oxidizing. Electrolytic plasma oxidizing (EPO) is an advanced technique to deposit thick and hard ceramic coatings on a number of aluminum alloys. However, the EPO treatment on Al-Si alloys with a high Si content has rarely been reported. In this research, an investigation was conducted to clarify the effects of silicon contents on the EPO coating formation, morphology, and composition. Cast hypereutectic 390 alloys ({approx} 17% Si) and hypoeutectic 319 alloys ({approx} 7% Si) were chosen as substrates. The coating morphology, composition, and microstructure of the EPO coatings on those substrates were investigated using scanning electron microscopy (SEM) with energy dispersive X-ray (EDX) analysis and X-ray diffraction (XRD). A stylus roughness tester was used for surface roughness measurement. It was found that the EPO process had four stages where each stage was corresponding to various coating surface morphology, composition, and phase structures, characterised by different coating growth mechanisms.

  20. Interactive effect of cerium and aluminum on the ignition point and the oxidation resistance of magnesium alloy

    International Nuclear Information System (INIS)

    This paper focused on the interactive effect of cerium (Ce) addition and aluminum (Al) content in magnesium alloy on ignition point and oxidation resistance. Ce content played an important role in improving the oxidation resistance of Mg alloy. Ignition point ascended with increasing Ce content. 0.25 wt% Ce content in Mg alloys could greatly improve tightness of the oxide film of Mg alloys. However, when Ce content in the alloy exceeded its solid solubility, ignition point descended. Furthermore, Al content in the alloy also influenced the ignition point. The higher the Al content was, the lower the ignition point

  1. Metallic nanoparticle shape and size effects on aluminum oxide-induced enhancement of exciton-plasmon coupling and quantum dot emission

    Science.gov (United States)

    Wing, Waylin J.; Sadeghi, Seyed M.; Gutha, Rithvik R.; Campbell, Quinn; Mao, Chuanbin

    2015-09-01

    We investigate the shape and size effects of gold metallic nanoparticles on the enhancement of exciton-plasmon coupling and emission of semiconductor quantum dots induced via the simultaneous impact of metal-oxide and plasmonic effects. This enhancement occurs when metallic nanoparticle arrays are separated from the quantum dots by a layered thin film consisting of a high index dielectric material (silicon) and aluminum oxide. Our results show that adding the aluminum oxide layer can increase the degree of polarization of quantum dot emission induced by metallic nanorods by nearly two times, when these nanorods have large aspect ratios. We show when the aspect ratio of these nanorods is reduced to half, the aluminum oxide loses its impact, leading to no improvement in the degree of polarization. These results suggest that a silicon/aluminum oxide layer can significantly enhance exciton-plasmon coupling when quantum dots are in the vicinity of metallic nanoantennas with high aspect ratios.

  2. Metallic nanoparticle shape and size effects on aluminum oxide-induced enhancement of exciton-plasmon coupling and quantum dot emission

    International Nuclear Information System (INIS)

    We investigate the shape and size effects of gold metallic nanoparticles on the enhancement of exciton-plasmon coupling and emission of semiconductor quantum dots induced via the simultaneous impact of metal-oxide and plasmonic effects. This enhancement occurs when metallic nanoparticle arrays are separated from the quantum dots by a layered thin film consisting of a high index dielectric material (silicon) and aluminum oxide. Our results show that adding the aluminum oxide layer can increase the degree of polarization of quantum dot emission induced by metallic nanorods by nearly two times, when these nanorods have large aspect ratios. We show when the aspect ratio of these nanorods is reduced to half, the aluminum oxide loses its impact, leading to no improvement in the degree of polarization. These results suggest that a silicon/aluminum oxide layer can significantly enhance exciton-plasmon coupling when quantum dots are in the vicinity of metallic nanoantennas with high aspect ratios

  3. Metallic nanoparticle shape and size effects on aluminum oxide-induced enhancement of exciton-plasmon coupling and quantum dot emission

    Energy Technology Data Exchange (ETDEWEB)

    Wing, Waylin J.; Sadeghi, Seyed M., E-mail: seyed.sadeghi@uah.edu; Gutha, Rithvik R.; Campbell, Quinn [Department of Physics, University of Alabama in Huntsville, Huntsville, Alabama 35899 (United States); Mao, Chuanbin [Department of Chemistry and Biochemistry, Stephenson Life Sciences Research Center, University of Oklahoma, Norman, Oklahoma 73019 (United States)

    2015-09-28

    We investigate the shape and size effects of gold metallic nanoparticles on the enhancement of exciton-plasmon coupling and emission of semiconductor quantum dots induced via the simultaneous impact of metal-oxide and plasmonic effects. This enhancement occurs when metallic nanoparticle arrays are separated from the quantum dots by a layered thin film consisting of a high index dielectric material (silicon) and aluminum oxide. Our results show that adding the aluminum oxide layer can increase the degree of polarization of quantum dot emission induced by metallic nanorods by nearly two times, when these nanorods have large aspect ratios. We show when the aspect ratio of these nanorods is reduced to half, the aluminum oxide loses its impact, leading to no improvement in the degree of polarization. These results suggest that a silicon/aluminum oxide layer can significantly enhance exciton-plasmon coupling when quantum dots are in the vicinity of metallic nanoantennas with high aspect ratios.

  4. Effect of Polar Environments on the Aluminum Oxide Shell Surrounding Aluminum Particles: Simulations of Surface Hydroxyl Bonding and Charge.

    Science.gov (United States)

    Padhye, Richa; Aquino, Adelia J A; Tunega, Daniel; Pantoya, Michelle L

    2016-06-01

    Density functional theory (DFT) calculations were performed to understand molecular variations on an alumina surface due to exposure to a polar environment. The analysis has strong implications for the reactivity of aluminum (Al) particles passivated by an alumina shell. Recent studies have shown a link between the carrier fluid used for Al powder intermixing and the reactivity of Al with fluorine containing reactive mixtures. Specifically, flame speeds show a threefold increase when polar liquids are used to intermix aluminum and fluoropolymer powder mixtures. It was hypothesized that the alumina lattice structure could be transformed due to hydrogen bonding forces exerted by the environment that induce modified bond distances and charges and influence reactivity. In this study, the alumina surface was analyzed using DFT calculations and model clusters as isolated systems embedded in polar environments (acetone and water). The conductor-like screening model (COSMO) was used to mimic environmental effects on the alumina surface. Five defect models for specific active -OH sites were investigated in terms of structures and vibrational -OH stretching frequencies. The observed changes of the surface OH sites invoked by the polar environment were compared to the bare surface. The calculations revealed a strong connection between the impact of carrier fluid polarity on the hydrogen bonding forces between the surface OH sites and surrounding species. Changes were observed in the OH characteristic properties such as OH distances (increase), atomic charges (increase), and OH stretching frequencies (decrease); these consequently improve OH surface reactivity. The difference between medium (acetone) and strong (water) polar environments was minimal in the COSMO approximation. PMID:27175545

  5. Multimillion atom simulations of dynamics of oxidation of an aluminum nanoparticle and nanoindentation on ceramics.

    Science.gov (United States)

    Vashishta, Priya; Kalia, Rajiv K; Nakano, Aiichiro

    2006-03-01

    We have developed a first-principles-based hierarchical simulation framework, which seamlessly integrates (1) a quantum mechanical description based on the density functional theory (DFT), (2) multilevel molecular dynamics (MD) simulations based on a reactive force field (ReaxFF) that describes chemical reactions and polarization, a nonreactive force field that employs dynamic atomic charges, and an effective force field (EFF), and (3) an atomistically informed continuum model to reach macroscopic length scales. For scalable hierarchical simulations, we have developed parallel linear-scaling algorithms for (1) DFT calculation based on a divide-and-conquer algorithm on adaptive multigrids, (2) chemically reactive MD based on a fast ReaxFF (F-ReaxFF) algorithm, and (3) EFF-MD based on a space-time multiresolution MD (MRMD) algorithm. On 1920 Intel Itanium2 processors, we have demonstrated 1.4 million atom (0.12 trillion grid points) DFT, 0.56 billion atom F-ReaxFF, and 18.9 billion atom MRMD calculations, with parallel efficiency as high as 0.953. Through the use of these algorithms, multimillion atom MD simulations have been performed to study the oxidation of an aluminum nanoparticle. Structural and dynamic correlations in the oxide region are calculated as well as the evolution of charges, surface oxide thickness, diffusivities of atoms, and local stresses. In the microcanonical ensemble, the oxidizing reaction becomes explosive in both molecular and atomic oxygen environments, due to the enormous energy release associated with Al-O bonding. In the canonical ensemble, an amorphous oxide layer of a thickness of approximately 40 angstroms is formed after 466 ps, in good agreement with experiments. Simulations have been performed to study nanoindentation on crystalline, amorphous, and nanocrystalline silicon nitride and silicon carbide. Simulation on nanocrystalline silicon carbide reveals unusual deformation mechanisms in brittle nanophase materials, due to

  6. Evaluation of the microstructural and photocatalytic properties of aluminum-doped zinc oxide coatings deposited by plasma spraying

    International Nuclear Information System (INIS)

    Aluminum-doped zinc oxide (AZO) material produced from a nanopowder agglomerate was deposited as a plasma-sprayed coating, and the resulting microstructural and photocatalytic properties of these coatings were investigated. The microstructure of the AZO coatings was analyzed by X-ray diffraction and scanning electron microscopy. Additionally, the photocatalytic degradation of methylene blue caused by the AZO coatings was estimated via ultraviolet–visible spectroscopy. The results of this study demonstrate that the AZO coatings deposited by plasma spraying can influence the photocatalytic degradation of methylene blue. - Highlights: • We doped aluminum (Al) in a zinc oxide (ZnO) coating using plasma spraying. • More significant recrystallization was observed after plasma spraying. • The surface of the Al-doped ZnO coating exhibited a microplatelet microstructure. • The Al-doped ZnO coating displayed high photocatalytic activities

  7. Evaluation of the microstructural and photocatalytic properties of aluminum-doped zinc oxide coatings deposited by plasma spraying

    Energy Technology Data Exchange (ETDEWEB)

    Su, C.Y., E-mail: cysu@ntut.edu.tw [Graduate Institute of Manufacturing Technology, National Taipei University of Technology, Taipei 106, Taiwan (China); Lu, C.T., E-mail: gayyag2000@hotmail.com [Graduate Institute of Manufacturing Technology, National Taipei University of Technology, Taipei 106, Taiwan (China); Hsiao, W.T., E-mail: Jesse_Hsiao@itri.org.tw [Materials and Chemical Research Laboratories, Industrial Technology Research Institute, Chutung 310, Taiwan (China); Liu, W.H., E-mail: xhan@itri.org.tw [Materials and Chemical Research Laboratories, Industrial Technology Research Institute, Chutung 310, Taiwan (China); Nano Technology Laboratory, Department of Materials Engineering, National Chung Hsing University, Taichung 402, Taiwan (China); Shieu, F.S., E-mail: fsshieu@dragon.nchu.edu.tw [Nano Technology Laboratory, Department of Materials Engineering, National Chung Hsing University, Taichung 402, Taiwan (China)

    2013-10-01

    Aluminum-doped zinc oxide (AZO) material produced from a nanopowder agglomerate was deposited as a plasma-sprayed coating, and the resulting microstructural and photocatalytic properties of these coatings were investigated. The microstructure of the AZO coatings was analyzed by X-ray diffraction and scanning electron microscopy. Additionally, the photocatalytic degradation of methylene blue caused by the AZO coatings was estimated via ultraviolet–visible spectroscopy. The results of this study demonstrate that the AZO coatings deposited by plasma spraying can influence the photocatalytic degradation of methylene blue. - Highlights: • We doped aluminum (Al) in a zinc oxide (ZnO) coating using plasma spraying. • More significant recrystallization was observed after plasma spraying. • The surface of the Al-doped ZnO coating exhibited a microplatelet microstructure. • The Al-doped ZnO coating displayed high photocatalytic activities.

  8. Pomegranate Alleviates Oxidative Damage and Neurotransmitter Alterations in Rats Brain Exposed to Aluminum Chloride and/or Gamma Radiation

    International Nuclear Information System (INIS)

    Aluminum and gamma radiation, both are potent neurotoxins and have been implicated in many human neuro degenerative diseases. The present study was designed to investigate the role of pomegranate in alleviating oxidative damage and alteration of neurotransmitters in the brain of rats exposed to aluminum chloride (AlCl3), and/or gamma radiation (IR). The results revealed that rats whole body exposed to γ- rays, (1 Gy/week up to 4 Gy), and/or administered aluminum chloride (35 mg/kg body weight), via gavages for 4 weeks, resulted in brain tissue damage, featuring by significant increase of the level of thiobarbituric acid reactive substances (TBARS), and advanced oxidation protein products (AOPP), associated with significant decrease of superoxide dismutase (SOD) and catalase (CAT) activities, as well as glutathione (GSH) content indicating occurrence of oxidative stress. A significant decrease of serotonin (5-HT) level associated with a significant increase of 5-hydroxyindole acetic acid (5-HIAA), in addition to a significant decrease in dopamine (DA), norepinephrine (NE) and epinephrine (EPI) contents recorded at the 1st, 7th and 14th day post-irradiation, indicating alterations in the metabolism of brain monoamines. On the other hand, the results exhibited that, supplementation of rats with pomegranate, via gavages, at a dose of 3 ml /kg body weight/ day, for 4 weeks along with AlCl3 with or without radiation has significantly ameliorated the changes occurred in the mentioned parameters and the values returned close to the normal ones. It could be concluded that pomegranate, by its antioxidant constituents might antagonize brain oxidative damage and minimize the severity of aluminum (Al), and/or radiation-induced neurotransmitters disorders

  9. Distribution of electric field near the surface of the aluminum oxide particle in the dust-electron thermal plasma

    International Nuclear Information System (INIS)

    We obtained the equation, which describes the distribution of electrical field in an equilibrium dust-electron plasma taking into account parameters of the electron gas inside the dust particles. The inclusion of these parameters performed on the basis of the model of ''solid- state plasma'', considering the condensed particle system as the ion core and the free electron gas. These calculations are performed for aluminum oxide particles

  10. Porous silicon carbide and aluminum oxide with unidirectional open porosity as model target materials for radioisotope beam production

    CERN Document Server

    Czapski, M; Tardivat, C; Stora, T; Bouville, F; Leloup, J; Luis, R Fernandes; Augusto, R Santos

    2013-01-01

    New silicon carbide (SiC) and aluminum oxide (Al2O3) of a tailor-made microstructure were produced using the ice-templating technique, which permits controlled pore formation conditions within the material. These prototypes will serve to verify aging of the new advanced target materials under irradiation with proton beams. Before this, the evaluation of their mechanical integrity was made based on the energy deposition spectra produced by FLORA codes. (C) 2013 Elsevier B.V. All rights reserved.

  11. Large-area sub-micron structured surfaces using micro injection moulding templates of nanoporous anodized Aluminum Oxide

    OpenAIRE

    Zhang, Nan; Harrison, S.; Meagher, P.; et al.

    2012-01-01

    This study demonstrates a mass production method using nanoporous Anodized Aluminum Oxide (AAO) templates as mould insert tools that are used to structure large area polymer surfaces by a micro injection moulding process. SEM and water contact angle measurements served to evaluate the effect of nanostructures on surface properties. Human umbilical vein endothelial cells were cultured on nano-structured and ultra-smooth surfaces of polymer parts. Experimental results indicated that...

  12. Synthesis of carbon nanotube arrays using ethanol in porous anodic aluminum oxide template

    Institute of Scientific and Technical Information of China (English)

    YU Guojun; WANG Sen; GONG Jinlong; ZHU Dezhang; HE Suixia; LI Yulan; ZHU Zhiyuan

    2005-01-01

    Carbon nanotube (CNT) arrays confined by porous anodic aluminum oxide (AAO) template were synthesized using ethanol as reactant carbon source at low pressure. Images by scanning electron microscope (SEM) and low magnification transmission electron microscopy (TEM) show that these CNTs have highly uniform outer diameter and length, absolutely controlled by the diameter and depth of nano-channel arrays of the AAO. High resolution transmission electron microscopy (HRTEM) imaging indicates that the graphitization of the CNT walls is better than the results reported on this kind of template-based CNT arrays, although it is not so good as that of multiwalled carbon nanotubes (MWCNTs) synthesized by catalysis. CNTs synthesized using acetylene as reactant gas show much less graphitization than those prepared using ethanol by comparing the results of HRTEM and Raman spectroscopy. The etching effects of decomposed OH radicals on the amorphous carbon and the roughness of AAO nano-channel arrays on the CNTs growth were employed to explain the graphitization and growth of the CNTs.

  13. Nanosecond laser ablation processes in aluminum-doped zinc-oxide for photovoltaic devices

    Energy Technology Data Exchange (ETDEWEB)

    Canteli, D., E-mail: david.canteli@ciemat.es [Division de Energias Renovables, Energia Solar Fotovoltaica, CIEMAT, Avda. Complutense, 22, 28040 Madrid (Spain); Fernandez, S. [Division de Energias Renovables, Energia Solar Fotovoltaica, CIEMAT, Avda. Complutense, 22, 28040 Madrid (Spain); Molpeceres, C. [Centro Laser, Universidad Politecnica de Madrid, Ctra. de Valencia Km 7.3, 28031 Madrid (Spain); Torres, I.; Gandia, J.J. [Division de Energias Renovables, Energia Solar Fotovoltaica, CIEMAT, Avda. Complutense, 22, 28040 Madrid (Spain)

    2012-09-15

    Highlights: Black-Right-Pointing-Pointer A study of the ablation of AZO thin films deposited at different temperature conditions with nanosecond UV laser light for photovoltaic devices has been performed. Black-Right-Pointing-Pointer The ablation threshold of AZO thin films was measured and related with the absorption coefficient of the films at the laser wavelength, showing a direct correspondence. Black-Right-Pointing-Pointer A change in the material structure in the areas closest to the edges of laser grooves made in samples deposited at temperatures below 100 Degree-Sign C was observed and studied. - Abstract: Aiming to a future use in thin film solar modules, the processing of aluminum doped zinc oxide thin films with good optoelectronic properties with a nanosecond-pulsed ultraviolet laser has been studied. The ablation threshold fluence of the films has been determined and associated with the material properties. The ablation process has been optimized and grooves with good properties for photovoltaic devices have been obtained. The morphology of the ablated surfaces has been observed by confocal microscopy and its structure has been characterized by Raman spectroscopy. The influence of ablation parameters like focus distance, pulse energy and repetition frequency in the groove morphology has been studied with special attention to the thermal effects on the material structure.

  14. Remarkable enhancement of upconversion luminescence on 2-D anodic aluminum oxide photonic crystals.

    Science.gov (United States)

    Wang, He; Yin, Ze; Xu, Wen; Zhou, Donglei; Cui, Shaobo; Chen, Xu; Cui, Haining; Song, Hongwei

    2016-05-21

    Lanthanide-doped upconversion nanoparticles (UCNPs) are attracting extensive attention due to their unique physical properties and great application potential. However, the lower luminescence quantum yield/strength is still an obstacle for real application. Local field modulation is a promising method to highly enhance the upconversion luminescence (UCL) of the UCNPs. In this work, a novel kind of two-dimensional photonic crystal (2D-PC), anodic aluminum oxides (AAOs), was explored to improve the UCL of NaYF4:Yb(3+),Er(3+) nanoplates (NPs). An optimum enhancement factor (EF) of 65-fold was obtained for the overall intensity of Er(3+) under 980 nm excitation, and 130-fold for the red emission. Systematic studies indicate that UCL enhancement mainly originates from the enlargement of the excitation field by scattering and reflection of AAO PCs. It should also be highlighted that the modulation of 2D-PC on the UCL of NaYF4:Yb(3+),Er(3+) NPs demonstrates weak size-dependent and thickness-dependent behavior, which is well consistent with the stimulated electromagnetic field distribution by the finite difference time domain (FDTD) method. PMID:27139324

  15. Effects of anodic aluminum oxide membrane on performance of nanostructured solar cells

    Science.gov (United States)

    Dang, Hongmei; Singh, Vijay

    2015-05-01

    Three nanowire solar cell device configurations have been fabricated to demonstrate the effects of the host anodized aluminum oxide (AAO) membrane on device performance. The three configurations show similar transmittance spectra, indicating that AAO membrane has negligible optical absorption. Power conversion efficiency (PCE) of the device is studied as a function of the carrier transport and collection in cell structures with and without AAO membrane. Free standing nanowire solar cells exhibit PCE of 9.9%. Through inclusion of AAO in solar cell structure, interface defects and traps caused by humidity and oxygen are reduced, and direct contact of CdTe tentacles with SnO2 and formation of micro shunt shorts are prevented; hence PCE is improved to 11.1%-11.3%. Partially embedded nanowire solar cells further reduce influence of non-ideal and non-uniform nanowire growth and generate a large amount of carriers in axial direction and also a small quantity of carriers in lateral direction, thus becoming a promising solar cell structure. Thus, including AAO membrane in solar cell structure provides favorable electro-optical properties as well as mechanical advantages.

  16. Vibration Durability Testing of Nickel Cobalt Aluminum Oxide (NCA Lithium-Ion 18650 Battery Cells

    Directory of Open Access Journals (Sweden)

    James Michael Hooper

    2016-04-01

    Full Text Available This paper outlines a study undertaken to determine if the electrical performance of Nickel Cobalt Aluminum Oxide (NCA 3.1 Ah 18650 battery cells can be degraded by road induced vibration typical of an electric vehicle (EV application. This study investigates if a particular cell orientation within the battery assembly can result in different levels of cell degradation. The 18650 cells were evaluated in accordance with Society of Automotive Engineers (SAE J2380 standard. This vibration test is synthesized to represent 100,000 miles of North American customer operation at the 90th percentile. This study identified that both the electrical performance and the mechanical properties of the NCA lithium-ion cells were relatively unaffected when exposed to vibration energy that is commensurate with a typical vehicle life. Minor changes observed in the cell’s electrical characteristics were deemed not to be statistically significant and more likely attributable to laboratory conditions during cell testing and storage. The same conclusion was found, irrespective of cell orientation during the test.

  17. Neutron spectrum measurements in the aluminum oxide filtered beam facility at the Brookhaven Medical Research Reactor

    International Nuclear Information System (INIS)

    Neutron spectrum measurements were performed on the aluminum oxide filter installed in the Brookhaven Medical Research Reactor (BMRR). For these measurements, activation foils were irradiated at the exit port of the beam facility. A technique based on dominant resonances in selected activation reactions was used to measure the epithermal neutron spectrum. The fast and intermediate-energy ranges of the neutron spectrum were measured by threshold reactions and 10B-shielded 235U fission reactions. Neutron spectral data were derived from the activation data by two approaches: (1) a short analysis which yields neutron flux values at the energies of the dominant or primary resonances in the epithermal activation reactions and integral flux data for neutrons above corresponding threshold or pseudo-threshold energies, and (2) the longer analysis which utilized all the activation data in a full-spectrum, unfolding process using the FERRET spectrum adjustment code. This paper gives a brief description of the measurement techniques, analysis methods, and the results obtained

  18. Fabrication of diameter-modulated and ultrathin porous nanowires in anodic aluminum oxide templates

    Energy Technology Data Exchange (ETDEWEB)

    Sulka, Grzegorz D., E-mail: Sulka@chemia.uj.edu.pl [Max Planck Institute of Microstructure Physics, Weinberg 2, 06120 Halle (Germany); Department of Physical Chemistry and Electrochemistry, Jagiellonian University, Ingardena 3, 30060 Krakow (Poland); Brzozka, Agnieszka [AGH University of Science and Technology, Faculty of Non-Ferrous Metals, Al. Mickiewicza 30, Krakow 30-059 (Poland); Liu, Lifeng [Max Planck Institute of Microstructure Physics, Weinberg 2, 06120 Halle (Germany)

    2011-05-30

    Graphical abstract: Display Omitted Highlights: > AAO templates with modulated pore diameter were fabricated by pulse anodization. > HA pulse duration tunes the shape of pores and the structure of AAO channels. > Au, Ag, Ni and Ag-Au diameter-modulated nanowires were synthetized. > Porous ultrathin Au nanowires were obtained by dealloying Ag-Au nanowires. - Abstract: Anodic aluminum oxide (AAO) membranes with modulated pore diameter were synthesized by pulse anodization in 0.3 M sulfuric acid at 1 deg. C. For AAO growth, a typical combination of alternating mild anodizing (MA) and hard anodizing (HA) pulses with applied potential pulses of 25 V and 35 V was applied. The control of the duration of HA pulses will provide an interesting way to tune the shape of pores and the structure of AAO channels. It was found that a non-uniform length of HA segments in cross section of AAO is usually observed when the HA pulse duration is shorter than 1.2 s. The pulse anodization performed with longer HA pulses leads to the formation of AAO templates with periodically modulated pore diameter and nearly uniform length of segments. Various diameter-modulated metallic nanowires (Au, Ag, Ni and Ag-Au) were fabricated by electrodeposition in the pores of anodic alumina membranes. A typical average nanowire diameter was about 30 nm and 48 nm for MA and HA nanowire segments, respectively. After a successful dealloying silver from Ag-Au nanowires, porous ultrathin Au nanowires were obtained.

  19. Optical constants of anodic aluminum oxide films formed in oxalic acid solution

    International Nuclear Information System (INIS)

    The anodic aluminum oxide (AAO) films with highly ordered nanopore arrays were prepared in oxalic acid solution under different anodizing voltage and time, its surface and cross section appearances were characterized by using field emission scanning electron microscopy, the transmission spectra with the interference fringes were measured at normal incidence over the wavelength range 200 to 2500 nm. Then the modified Swanepoel method was used for the determination of the optical constants and thickness of the free standing AAO films. The results indicate that the refractive index increases with the increase of anodizing voltage and the decrease of anodizing time, which is mainly due to the content of Al2O3 with octahedron increases in the AAO films. The dispersion of the refractive index is discussed in terms of the single-oscillator Wemple-DiDomenico model, and the energy dependence of the absorption coefficient can be described using the direct transition model proposed by Tauc. Likewise, the optical energy gap Eg is derived from Tauc's extrapolation, and Eg increases from 4.178 to 4.256 eV with the anodizing voltage, but is weakly dependent on anodizing time. All the results are self-consistent in the paper

  20. Ru nanostructure fabrication using an anodic aluminum oxide nanotemplate and highly conformal Ru atomic layer deposition

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Woo-Hee; Park, Sang-Joon; Son, Jong-Yeog; Kim, Hyungjun [Department of Material Science and Engineering, POSTECH Pohang University of Science and Technology, San 31, Hyoja-Dong, Nam-Gu, Pohang 790-784 (Korea, Republic of)

    2008-01-30

    We fabricated metallic nanostructures directly on Si substrates through a hybrid nanoprocess combining atomic layer deposition (ALD) and a self-assembled anodic aluminum oxide (AAO) nanotemplate. ALD Ru films with Ru(DMPD)(EtCp) as a precursor and O{sub 2} as a reactant exhibited high purity and low resistivity with negligible nucleation delay and low roughness. These good growth characteristics resulted in the excellent conformality for nanometer-scale vias and trenches. Additionally, AAO nanotemplates were fabricated directly on Si and Ti/Si substrates through a multiple anodization process. AAO nanotemplates with various hole sizes (30-100 nm) and aspect ratios (2:1-20:1) were fabricated by controlling the anodizing process parameters. The barrier layers between AAO nanotemplates and Si substrates were completely removed by reactive ion etching (RIE) using BCl{sub 3} plasma. By combining the ALD Ru and the AAO nanotemplate, Ru nanostructures with controllable sizes and shapes were prepared on Si and Ti/Si substrates. The Ru nanowire array devices as a platform for sensor devices exhibited befitting properties of good ohmic contact and high surface/volume ratio.

  1. Significance of novel bioinorganic anodic aluminum oxide nanoscaffolds for promoting cellular response

    Science.gov (United States)

    Poinern, Gérrard Eddy Jai; Shackleton, Robert; Mamun, Shariful Islam; Fawcett, Derek

    2011-01-01

    Tissue engineering is a multidisciplinary field that can directly benefit from the many advancements in nanotechnology and nanoscience. This article reviews a novel biocompatible anodic aluminum oxide (AAO, alumina) membrane in terms of tissue engineering. Cells respond and interact with their natural environment, the extracellular matrix, and the landscape of the substrate. The interaction with the topographical features of the landscape occurs both in the micrometer and nanoscales. If all these parameters are favorable to the cell, the cell will respond in terms of adhesion, proliferation, and migration. The role of the substrate/scaffold is crucial in soliciting a favorable response from the cell. The size and type of surface feature can directly influence the response and behavior of the cell. In the case of using an AAO membrane, the surface features and porosity of the membrane can be dictated at the nanoscale during the manufacturing stage. This is achieved by using general laboratory equipment to perform a relatively straightforward electrochemical process. During this technique, changing the operational parameters of the process directly controls the nanoscale features produced. For example, the pore size, pore density, and, hence, density can be effectively controlled during the synthesis of the AAO membrane. In addition, being able to control the pore size and porosity of a biomaterial such as AAO significantly broadens its application in tissue engineering. PMID:24198483

  2. Optical constants of anodic aluminum oxide films formed in oxalic acid solution

    Energy Technology Data Exchange (ETDEWEB)

    Wang Jian [College of Physics and Electronic Engineering, Northwest Normal University, Lanzhou 730070 (China); Wang Chengwei [College of Physics and Electronic Engineering, Northwest Normal University, Lanzhou 730070 (China); State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China)], E-mail: cwwang@nwnu.edu.cn; Li Yan [College of Physics and Electronic Engineering, Northwest Normal University, Lanzhou 730070 (China); Liu Weimin [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China)

    2008-09-01

    The anodic aluminum oxide (AAO) films with highly ordered nanopore arrays were prepared in oxalic acid solution under different anodizing voltage and time, its surface and cross section appearances were characterized by using field emission scanning electron microscopy, the transmission spectra with the interference fringes were measured at normal incidence over the wavelength range 200 to 2500 nm. Then the modified Swanepoel method was used for the determination of the optical constants and thickness of the free standing AAO films. The results indicate that the refractive index increases with the increase of anodizing voltage and the decrease of anodizing time, which is mainly due to the content of Al{sub 2}O{sub 3} with octahedron increases in the AAO films. The dispersion of the refractive index is discussed in terms of the single-oscillator Wemple-DiDomenico model, and the energy dependence of the absorption coefficient can be described using the direct transition model proposed by Tauc. Likewise, the optical energy gap E{sub g} is derived from Tauc's extrapolation, and E{sub g} increases from 4.178 to 4.256 eV with the anodizing voltage, but is weakly dependent on anodizing time. All the results are self-consistent in the paper.

  3. Ru nanostructure fabrication using an anodic aluminum oxide nanotemplate and highly conformal Ru atomic layer deposition.

    Science.gov (United States)

    Kim, Woo-Hee; Park, Sang-Joon; Son, Jong-Yeog; Kim, Hyungjun

    2008-01-30

    We fabricated metallic nanostructures directly on Si substrates through a hybrid nanoprocess combining atomic layer deposition (ALD) and a self-assembled anodic aluminum oxide (AAO) nanotemplate. ALD Ru films with Ru(DMPD)(EtCp) as a precursor and O(2) as a reactant exhibited high purity and low resistivity with negligible nucleation delay and low roughness. These good growth characteristics resulted in the excellent conformality for nanometer-scale vias and trenches. Additionally, AAO nanotemplates were fabricated directly on Si and Ti/Si substrates through a multiple anodization process. AAO nanotemplates with various hole sizes (30-100 nm) and aspect ratios (2:1-20:1) were fabricated by controlling the anodizing process parameters. The barrier layers between AAO nanotemplates and Si substrates were completely removed by reactive ion etching (RIE) using BCl(3) plasma. By combining the ALD Ru and the AAO nanotemplate, Ru nanostructures with controllable sizes and shapes were prepared on Si and Ti/Si substrates. The Ru nanowire array devices as a platform for sensor devices exhibited befitting properties of good ohmic contact and high surface/volume ratio. PMID:21817499

  4. Fabrication of diameter-modulated and ultrathin porous nanowires in anodic aluminum oxide templates

    International Nuclear Information System (INIS)

    Graphical abstract: Display Omitted Highlights: → AAO templates with modulated pore diameter were fabricated by pulse anodization. → HA pulse duration tunes the shape of pores and the structure of AAO channels. → Au, Ag, Ni and Ag-Au diameter-modulated nanowires were synthetized. → Porous ultrathin Au nanowires were obtained by dealloying Ag-Au nanowires. - Abstract: Anodic aluminum oxide (AAO) membranes with modulated pore diameter were synthesized by pulse anodization in 0.3 M sulfuric acid at 1 deg. C. For AAO growth, a typical combination of alternating mild anodizing (MA) and hard anodizing (HA) pulses with applied potential pulses of 25 V and 35 V was applied. The control of the duration of HA pulses will provide an interesting way to tune the shape of pores and the structure of AAO channels. It was found that a non-uniform length of HA segments in cross section of AAO is usually observed when the HA pulse duration is shorter than 1.2 s. The pulse anodization performed with longer HA pulses leads to the formation of AAO templates with periodically modulated pore diameter and nearly uniform length of segments. Various diameter-modulated metallic nanowires (Au, Ag, Ni and Ag-Au) were fabricated by electrodeposition in the pores of anodic alumina membranes. A typical average nanowire diameter was about 30 nm and 48 nm for MA and HA nanowire segments, respectively. After a successful dealloying silver from Ag-Au nanowires, porous ultrathin Au nanowires were obtained.

  5. Growth control of carbon nanotubes using by anodic aluminum oxide nano templates.

    Science.gov (United States)

    Park, Yong Seob; Choi, Won Seek; Yi, Junsin; Lee, Jaehyeong

    2014-05-01

    Anodic Aluminum Oxide (AAO) template prepared in acid electrolyte possess regular and highly anisotropic porous structure with pore diameter range from five to several hundred nanometers, and with a density of pores ranging from 10(9) to 10(11) cm(-2). AAO can be used as microfilters and templates for the growth of CNTs and metal or semiconductor nanowires. Varying anodizing conditions such as temperature, electrolyte, applied voltage, anodizing and widening time, one can control the diameter, the length, and the density of pores. In this work, we deposited Al thin film by radio frequency magnetron sputtering method to fabricate AAO nano template and synthesized multi-well carbon nanotubes on a glass substrate by microwave plasma-enhanced chemical vapor deposition (MPECVD). AAO nano-porous templates with various pore sizes and depths were introduced to control the dimension and density of CNT arrays. The AAO nano template was synthesize on glass by two-step anodization technique. The average diameter and interpore distance of AAO nano template are about 65 nm and 82 nm. The pore density and AAO nano template thickness are about 2.1 x 10(10) pores/cm2 and 1 microm, respectively. Aligned CNTs on the AAO nano template were synthesized by MPECVD at 650 degrees C with the Ni catalyst layer. The length and diameter of CNTs were grown 2 microm and 50 nm, respectively. PMID:24734654

  6. Monolayer-directed Assembly and Magnetic Properties of FePt Nanoparticles on Patterned Aluminum Oxide

    Directory of Open Access Journals (Sweden)

    Guus Rijnders

    2010-03-01

    Full Text Available FePt nanoparticles (NPs were assembled on aluminum oxide substrates, and their ferromagnetic properties were studied before and after thermal annealing. For the first time, phosph(onates were used as an adsorbate to form self-assembled monolayers (SAMs on alumina to direct the assembly of NPs onto the surface. The Al2O3 substrates were functionalized with aminobutylphosphonic acid (ABP or phosphonoundecanoic acid (PNDA SAMs or with poly(ethyleneimine (PEI as a reference. FePt NPs assembled on all of these monolayers, but much less on unmodified Al2O3, which shows that ligand exchange at the NPs is the most likely mechanism of attachment. Proper modification of the Al2O3 surface and controlling the immersion time of the modified Al2O3 substrates into the FePt NP solution resulted in FePt NPs assembly with controlled NP density. Alumina substrates were patterned by microcontact printing using aminobutylphosphonic acid as the ink, allowing local NP assembly. Thermal annealing under reducing conditions (96%N2/4%H2 led to a phase change of the FePt NPs from the disordered FCC phase to the ordered FCT phase. This resulted in ferromagnetic behavior at room temperature. Such a process can potentially be applied in the fabrication of spintronic devices.

  7. Nanosecond laser ablation processes in aluminum-doped zinc-oxide for photovoltaic devices

    International Nuclear Information System (INIS)

    Highlights: ► A study of the ablation of AZO thin films deposited at different temperature conditions with nanosecond UV laser light for photovoltaic devices has been performed. ► The ablation threshold of AZO thin films was measured and related with the absorption coefficient of the films at the laser wavelength, showing a direct correspondence. ► A change in the material structure in the areas closest to the edges of laser grooves made in samples deposited at temperatures below 100 °C was observed and studied. - Abstract: Aiming to a future use in thin film solar modules, the processing of aluminum doped zinc oxide thin films with good optoelectronic properties with a nanosecond-pulsed ultraviolet laser has been studied. The ablation threshold fluence of the films has been determined and associated with the material properties. The ablation process has been optimized and grooves with good properties for photovoltaic devices have been obtained. The morphology of the ablated surfaces has been observed by confocal microscopy and its structure has been characterized by Raman spectroscopy. The influence of ablation parameters like focus distance, pulse energy and repetition frequency in the groove morphology has been studied with special attention to the thermal effects on the material structure.

  8. Removal of trivalent chromium from aqueous solution using aluminum oxide hydroxide.

    Science.gov (United States)

    Bedemo, Agaje; Chandravanshi, Bhagwan Singh; Zewge, Feleke

    2016-01-01

    Water is second most essential for human being. Contamination of water makes it unsuitable for human consumption. Chromium ion is released to water bodies from various industries having high toxicity which affects the biota life in these waters. In this study aluminum oxide hydroxide was tested for its efficiency to remove trivalent chromium from aqueous solutions through batch mode experiments. Chromium concentrations in aqueous solutions and tannery waste water before and after adsorption experiments were determined using flame atomic absorption spectrometry. The effects of pH, contact time, initial concentration and adsorbent dosage on the adsorption of Cr(III) were studied. The study revealed that more than 99 % removal of Cr(III) was achieved over wide range of initial pH (3-10). The optimum conditions for the removal of Cr(III) were found to be at pH 4-6 with 40 g/L adsorbent dose at 60 min of contact time. The adsorption capacity was assessed using Langmuir and Freundlich isotherms. The equilibrium data at varying adsorbent dose obeyed the two isotherms. The adsorbent was found to be efficient for the removal of Cr(III) from tannery waste effluent. PMID:27547663

  9. Sex-Dependent Depression-Like Behavior Induced by Respiratory Administration of Aluminum Oxide Nanoparticles.

    Science.gov (United States)

    Zhang, Xin; Xu, Yan; Zhou, Lian; Zhang, Chengcheng; Meng, Qingtao; Wu, Shenshen; Wang, Shizhi; Ding, Zhen; Chen, Xiaodong; Li, Xiaobo; Chen, Rui

    2015-12-01

    Ultrafine aluminum oxide, which are abundant in ambient and involved occupational environments, are associated with neurobehavioral alterations. However, few studies have focused on the effect of sex differences following exposure to environmental Al₂O₃ ultrafine particles. In the present study, male and female mice were exposed to Al₂O₃ nanoparticles (NPs) through a respiratory route. Only the female mice showed depression-like behavior. Although no obvious pathological changes were observed in mice brain tissues, the neurotransmitter and voltage-gated ion channel related gene expression, as well as the small molecule metabolites in the cerebral cortex, were differentially modulated between male and female mice. Both mental disorder-involved gene expression levels and metabolomics analysis results strongly suggested that glutamate pathways were implicated in sex differentiation induced by Al₂O₃ NPs. Results demonstrated the potential mechanism of environmental ultrafine particle-induced depression-like behavior and the importance of sex dimorphism in the toxic research of environmental chemicals. PMID:26690197

  10. Sex-Dependent Depression-Like Behavior Induced by Respiratory Administration of Aluminum Oxide Nanoparticles

    Directory of Open Access Journals (Sweden)

    Xin Zhang

    2015-12-01

    Full Text Available Ultrafine aluminum oxide, which are abundant in ambient and involved occupational environments, are associated with neurobehavioral alterations. However, few studies have focused on the effect of sex differences following exposure to environmental Al2O3 ultrafine particles. In the present study, male and female mice were exposed to Al2O3 nanoparticles (NPs through a respiratory route. Only the female mice showed depression-like behavior. Although no obvious pathological changes were observed in mice brain tissues, the neurotransmitter and voltage-gated ion channel related gene expression, as well as the small molecule metabolites in the cerebral cortex, were differentially modulated between male and female mice. Both mental disorder-involved gene expression levels and metabolomics analysis results strongly suggested that glutamate pathways were implicated in sex differentiation induced by Al2O3 NPs. Results demonstrated the potential mechanism of environmental ultrafine particle-induced depression-like behavior and the importance of sex dimorphism in the toxic research of environmental chemicals.

  11. Aluminum oxide passivated radial junction sub-micrometre pillar array textured silicon solar cells

    International Nuclear Information System (INIS)

    We report radial, p–n junction, sub-micrometre, pillar array textured solar cells, fabricated on an n-type Czochralski silicon wafer. Relatively simple processing schemes such as metal-assisted chemical etching and spin on dopant techniques were employed for the fabrication of the proposed solar cells. Atomic layer deposition (ALD) grown aluminum oxide (Al2O3) was employed as a surface passivation layer on the B-doped emitter surface. In spite of the fact that the sub-micrometre pillar array textured surface has a relatively high surface-to-volume ratio, we observed an open circuit voltage (VOC) and a short circuit current density (JSC) as high as 572 mV and 29.9 mA cm−2, respectively, which leads to a power conversion efficiency in excess of 11.30%, for the optimized structure of the solar cell described herein. Broadband omnidirectional antireflection effects along with the light trapping property of the sub-micrometre, pillar array textured surface and the excellent passivation quality of the ALD-grown Al2O3 on the B-doped emitter surface were responsible for the enhanced electrical performance of the proposed solar cells. (paper)

  12. Substrate surface polariton splitting due to thin zinc oxide and aluminum nitride films presence

    International Nuclear Information System (INIS)

    Surface polariton (SP) is the non-radiative interface electromagnetic mode, propagating along the interface between two media, if one of them is absorbing (metal, semiconductor or dielectric with the strong absorption bands) and exponentially decaying out of the interface. The introduction of a transition layer at this interface results in the shift and broadening of SP. This effect can be used to obtain film parameters (thickness and optical constants) in the region of SP existence. Zinc oxide (ZnO) films (100–300 nm thick) have been prepared on the LiF and CaF2 substrates and aluminum nitride films (40 and 400 nm thick) have been prepared on sapphire substrates. The SP spectra have been measured by attenuated total reflection (ATR) technique. IFS66v (BRUKER) infrared Fourier-transform spectrometer was used for ATR and near normal incidence external reflection spectral measurements. Angular dependencies of the absorption bands positions in the ATR spectra give the dispersion of SP. The measured SP dispersion is compared with one calculated using the film parameters obtained by dispersion analysis of the external reflectivity spectra. The splitting of the dispersion curves of substrate SP was found. It is due to the resonance interaction of substrate SP with the film optical phonons. This splitting is proportional to the square root of the film thickness. For ZnO films on CaF2 “long range” SPs were observed. These effects allow estimate film complex dielectric function in the region under consideration.

  13. Prediction model for oxide thickness on aluminum alloy cladding during irradiation

    International Nuclear Information System (INIS)

    An empirical model predicting the oxide film thickness on aluminum alloy cladding during irradiation has been developed as a function of irradiation time, temperature, heat flux, pH, and coolant flow rate. The existing models in the literature are neither consistent among themselves nor fit the measured data very well. They also lack versatility for various reactor situations such as a pH other than 5, high coolant flow rates, and fuel life longer than ∼1200 hrs. Particularly, they were not intended for use in irradiation situations. The newly developed model is applicable to these in-reactor situations as well as ex-reactor tests, and has a more accurate prediction capability. The new model demonstrated with consistent predictions to the measured data of UMUS and SIMONE fuel tests performed in the HFR, Petten, tests results from the ORR, and IRIS tests from the OSIRIS and to the data from the out-of-pile tests available in the literature as well. (author)

  14. Aluminum Oxide-Coated Sand for Improved Treatment of Urban Stormwater.

    Science.gov (United States)

    Johannsen, Lisbeth L; Cederkvist, Karin; Holm, Peter E; Ingvertsen, Simon T

    2016-03-01

    Infiltration facilities for urban stormwater runoff, such as biofilters, rain gardens, and curb extensions, typically contain an engineered soil mixture for effective drainage and retention of pollutants. The treatment efficiency of such soils is generally considered high for many pollutants. However, recent studies have revealed that in situ mobilization of soil organic matter may cause leaching of a range of pollutants and therefore diminish the long-term performance of engineered soils. The purpose of this study was to develop and test sand coated with aluminum (Al) oxides for improving the retention of organic matter and a range of common pollutants in engineered soils. Two alternative Al-coating methods were successfully developed in the laboratory. The Al coating of the sand increased the specific surface area from 0.3 to 1.1 m g to 0.87 to 2.2 m g depending on sand fraction. One method was upscaled to produce 100 kg coated sand. The stability of the coatings was studied in batch experiments. Dry shaking showed a high resistance of the coating against mechanical stress. Increasing the ionic strength by the addition of NaCl seemed to improve the stability of the coatings. Varying pH showed that acidic conditions could compromise the Al coating stability. Overall, one coating method showed slightly better results in terms of higher surface area and stability. The Al coating significantly improved the retention capacity of the sand toward dissolved organic carbon. The results document that it is possible to coat sand effectively with Al oxides and consequently to improve the retention capacity and lifetime of engineered soils for urban stormwater management. PMID:27065420

  15. The effect of plasma electrolytic oxidation on the mean stress sensitivity of the fatigue life of the 6082 aluminum alloy

    Science.gov (United States)

    Winter, L.; Morgenstern, R.; Hockauf, K.; Lampke, T.

    2016-03-01

    In this work the mean stress influence on the high cycle fatigue behavior of the plasma electrolytic oxidized (PEO) 6082 aluminum alloy (AlSi1MgMn) is investigated. The present study is focused on the fatigue life time and the susceptibility of fatigue-induced cracking of the oxide coating and their dependence on the applied mean stress. Systematic work is done comparing conditions with and without PEO treatment, which have been tested using three different load ratios. For the uncoated substrate the cycles to failure show a significant dependence on the mean stress, which is typical for aluminum alloys. With increased load ratio and therefore increased mean stress, the fatigue strength decreases. The investigation confirms the well-known effect of PEO treatment on the fatigue life: The fatigue strength is significantly reduced by the PEO process, compared to the uncoated substrate. However, also the mean stress sensitivity of the fatigue performance is reduced. The fatigue limit is not influenced by an increasing mean stress for the PEO treated conditions. This effect is firstly shown in these findings and no explanation for this effect can be found in literature. Supposedly the internal compressive stresses and the micro-cracks in the oxide film have a direct influence on the crack initiation and growth from the oxide film through the interface and in the substrate. Contrary to these findings, the susceptibility of fatigue-induced cracking of the oxide coating is influenced by the load ratio. At tension-tension loading a large number of cracks, which grow partially just in the aluminum substrate, are present. With decreasing load ratio to alternating tension-compression stresses, the crack number and length increases and shattering of the oxide film is more pronounced due to the additional effective compressive part of the load cycle.

  16. Microstructure and corrosion behavior of micro-arc oxidation coating on 6061 aluminum alloy pre-treated by high-temperature oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Shen, Dejiu, E-mail: sdj217@ysu.edu.cn [State Key Laboratory of Metastable Materials Science and Technology, College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); Li, Guolong, E-mail: lglysu@163.com [State Key Laboratory of Metastable Materials Science and Technology, College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); Guo, Changhong [College of Mechanical Engineering, Yanshan University, Qinhuangdao 066004 (China); Zou, Jie [China Aviation Industry Chengdu Engine (Group) Co. Ltd., Chengdu 610503 (China); Cai, Jingrui; He, Donglei; Ma, Haojie; Liu, Fangfei [State Key Laboratory of Metastable Materials Science and Technology, College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China)

    2013-12-15

    In this paper, we investigate the microstructure and corrosion behavior of the micro-arc oxidation (MAO) coating on 6061 aluminum alloy that pre-treated by high-temperature oxidation (HTO). Microstructure, chemical and corrosion behaviors of the fabricated MAO ceramic coatings were studied by using scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS) and electrochemical corrosion tests. The results reveal that the pre-fabricated HTO film remarkably affects the formation of the MAO coating, leads to an enriched content of Mg, and decreases the compactness of the coating. The corrosion resistance of the 6061 aluminum alloy has been significantly improved by treatments of HTO, normal MAO (NMAO) and HTO pre-treated MAO (HTO-MAO), and the NMAO coating exhibits the best corrosion performance. The content of Mg in HTO pre-fabricated film is remarkedly higher than that in the substrate, which greatly influences the formation of the MAO coating.

  17. Microstructure and corrosion behavior of micro-arc oxidation coating on 6061 aluminum alloy pre-treated by high-temperature oxidation

    International Nuclear Information System (INIS)

    In this paper, we investigate the microstructure and corrosion behavior of the micro-arc oxidation (MAO) coating on 6061 aluminum alloy that pre-treated by high-temperature oxidation (HTO). Microstructure, chemical and corrosion behaviors of the fabricated MAO ceramic coatings were studied by using scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS) and electrochemical corrosion tests. The results reveal that the pre-fabricated HTO film remarkably affects the formation of the MAO coating, leads to an enriched content of Mg, and decreases the compactness of the coating. The corrosion resistance of the 6061 aluminum alloy has been significantly improved by treatments of HTO, normal MAO (NMAO) and HTO pre-treated MAO (HTO-MAO), and the NMAO coating exhibits the best corrosion performance. The content of Mg in HTO pre-fabricated film is remarkedly higher than that in the substrate, which greatly influences the formation of the MAO coating.

  18. Mechanochemical reactions and strengthening in epoxy-cast aluminum iron-oxide mixtures

    Science.gov (United States)

    Ferranti, Louis, Jr.

    2007-12-01

    -viscoplastic deformation and brittle fracture behaviors. Significant elastic and plastic deformation during both loading and unloading stages is observed, with approximately 50% elastic recovery of total axial strain occurring rapidly (tens of microseconds) after impact. Coupling high-speed camera images and velocity interferometry measurements shows that the elastic recovery coincides with peak axial strain and the elastic and plastic wave interaction. The incorporation of nano-scale aluminum particles enhances the dynamic stress-strain response and significantly improves the composites' resilience to impact as compared to pure epoxy, and with the use of micron-scale aluminum particles. Post-mortem analysis of recovered Taylor impacted specimens indicates evidence of early stages of strain-induced reactions occurring at select stress, strain, and strain rates. The observed reaction products correlate with results of thermal analysis, which include DTA and in situ high temperature x-ray diffraction (HTXRD). Central to this study was the interaction of metal-oxide powder mixtures with the epoxy matrix and how their chemical and mechanical properties balance to form a structural energetic material system. The study focuses on describing the underlying principles governing the deformation and fracture behavior, processing characteristics of epoxy-cast Al+Fe2O3 powder mixtures, mechanochemical sensitivity, and reaction response. In order to accomplish this, the effects of size, morphology, and distribution of particles were evaluated based on mechanical and chemical response to high pressures and combined stress-strain states using time-resolved measurements.

  19. Influence of the surface pre-treatment of aluminum on the processes of formation of cerium oxides protective films

    Science.gov (United States)

    Andreeva, R.; Stoyanova, E.; Tsanev, A.; Stoychev, D.

    2016-03-01

    It is known that there is special interest in the contemporary investigations on conversion treatment of aluminum aimed at promoting its corrosion stability, which is focused on electrolytes on the basis of salts of metals belonging to the group of rare-earth elements. Their application is especially attractive, as it enables a successful substitution of the presently applied highly efficient, but at the same time toxic Cr6+-containing electrolytes. The present paper presents a study on the influence of the preliminary alkaline activation and acidic de-oxidation of the aluminum surface on the processes of immersion formation of protective cerium oxides films on Al 1050. The results obtained show that their deposition from simple electrolytes (containing only salts of Ce3+ ions) on the Al surface, treated only in alkaline solution, occurs at a higher rate, which leads to preparing thicker oxide films having a better protective ability. In the cases when the formation of oxide films is realized in a complex electrolyte (containing salts of Ce3+ and Cu2+ ions), better results are obtained with respect to the morphology and protective action of cerium oxides film on samples that have been consecutively activated in alkaline solution and deoxidized in acidic solution. Electrochemical investigations were carried out in a model corrosion medium (0.1 M NaCl); it was shown that the cerium protective films, deposited by immersion, have a cathodic character with regard to the aluminum support and inhibit the occurrence of the depolarizing corrosion process -- the reaction of oxygen reduction.

  20. Growth of porous type anodic oxide films at micro-areas on aluminum exposed by laser irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Kikuchi, Tatsuya [Graduate School of Engineering, Hokkaido University, N13-W8, Kita-Ku, Sapporo 060-8628 (Japan)], E-mail: kiku@eng.hokudai.ac.jp; Sakairi, Masatoshi [Graduate School of Engineering, Hokkaido University, N13-W8, Kita-Ku, Sapporo 060-8628 (Japan); Takahashi, Hideaki [Asahikawa National College of Technology, Syunkohdai, 2-2, 1-6, Asahikawa 071-8142 (Japan)

    2009-11-30

    Aluminum covered with pore-sealed anodic oxide films was irradiated with a pulsed Nd-YAG laser to remove the oxide film at micro-areas. The specimen was re-anodized for long periods to examine the growth of porous anodic oxide films at the area where substrate had been exposed by measuring current variations and morphological changes in the oxide during the re-anodizing. The chemical dissolution resistance of the pore-sealed anodic oxide films in an oxalic acid solution was also examined by measuring time-variations in rest potentials during immersion. The resistance to chemical dissolution of the oxide film became higher with increasing pore-sealing time and showed higher values at lower solution temperatures. During potentiostatic re-anodizing at five 35-{mu}m wide and 4-mm long lines for 72 h after the film was removed the measured current was found to increase linearly with time. Semicircular columnar-shaped porous type anodic oxide was found to form during the re-anodizing at the laser-irradiated area, and was found to grow radially, thus resulting in an increase in the diameter. After long re-anodizing, the central and top parts of the oxide protruded along the longitudinal direction of the laser-irradiated area. The volume expansion during re-anodizing resulted in the formation of cracks, parallel to the lines, in the oxide film formed during the first anodizing.

  1. Growth of porous type anodic oxide films at micro-areas on aluminum exposed by laser irradiation

    International Nuclear Information System (INIS)

    Aluminum covered with pore-sealed anodic oxide films was irradiated with a pulsed Nd-YAG laser to remove the oxide film at micro-areas. The specimen was re-anodized for long periods to examine the growth of porous anodic oxide films at the area where substrate had been exposed by measuring current variations and morphological changes in the oxide during the re-anodizing. The chemical dissolution resistance of the pore-sealed anodic oxide films in an oxalic acid solution was also examined by measuring time-variations in rest potentials during immersion. The resistance to chemical dissolution of the oxide film became higher with increasing pore-sealing time and showed higher values at lower solution temperatures. During potentiostatic re-anodizing at five 35-μm wide and 4-mm long lines for 72 h after the film was removed the measured current was found to increase linearly with time. Semicircular columnar-shaped porous type anodic oxide was found to form during the re-anodizing at the laser-irradiated area, and was found to grow radially, thus resulting in an increase in the diameter. After long re-anodizing, the central and top parts of the oxide protruded along the longitudinal direction of the laser-irradiated area. The volume expansion during re-anodizing resulted in the formation of cracks, parallel to the lines, in the oxide film formed during the first anodizing.

  2. Effects of aluminum additions to gas atomized reaction synthesis produced oxide dispersion strengthened alloys

    Science.gov (United States)

    Spicher, Alexander Lee

    The production of an aluminum containing ferritic oxide dispersion strengthened (ODS) alloy was investigated. The production method used in this study was gas atomization reaction synthesis (GARS). GARS was chosen over the previously commercial method of mechanical alloying (MA) process due to complications from this process. The alloy compositions was determined from three main components; corrosion resistance, dispersoid formation, and additional elements. A combination of Cr and Al were necessary in order to create a protective oxide in the steam atmosphere that the boiler tubing in the next generation of coal-fired power plants would be exposed to. Hf and Y were chosen as dispersoid forming elements due to their increased thermal stability and potential to avoid decreased strength caused by additions of Al to traditional ODS materials. W was used as an additive due to benefits as a strengthener as well as its benefits for creep rupture time. The final composition chosen for the alloy was Fe-16Cr-12Al-0.9W-0.25Hf-0.2Y at%. The aforementioned alloy, GA-1-198, was created through gas atomization with atomization gas of Ar-300ppm O2. The actual composition created was found to be Fe-15Cr-12.3Al-0.9W-0.24Hf-0.19Y at%. An additional alloy that was nominally the same without the inclusion of aluminum was created as a comparison for the effects on mechanical and corrosion properties. The actual composition of the comparison alloy, GA-1-204, was Fe-16Cr-0Al-0.9W-0.25Hf-0.24Y at%. An investigation on the processing parameters for these alloys was conducted on the GA-1-198 alloy. In order to predict the necessary amount of time for heat treatment, a diffusion study was used to find the diffusion rate of oxygen in cast alloys with similar composition. The diffusion rate was found to be similar to that of other GARS compositions that have been created without the inclusion of aluminum. The effect of heat treatment time was investigated with temperatures of 950°C, 1000

  3. Rapid susceptibility testing and microcolony analysis of Candida spp. cultured and imaged on porous aluminum oxide.

    Directory of Open Access Journals (Sweden)

    Colin J Ingham

    Full Text Available BACKGROUND: Acquired resistance to antifungal agents now supports the introduction of susceptibility testing for species-drug combinations for which this was previously thought unnecessary. For pathogenic yeasts, conventional phenotypic testing needs at least 24 h. Culture on a porous aluminum oxide (PAO support combined with microscopy offers a route to more rapid results. METHODS: Microcolonies of Candida species grown on PAO were stained with the fluorogenic dyes Fun-1 and Calcofluor White and then imaged by fluorescence microscopy. Images were captured by a charge-coupled device camera and processed by publicly available software. By this method, the growth of yeasts could be detected and quantified within 2 h. Microcolony imaging was then used to assess the susceptibility of the yeasts to amphotericin B, anidulafungin and caspofungin (3.5 h culture, and voriconazole and itraconazole (7 h culture. SIGNIFICANCE: Overall, the results showed good agreement with EUCAST (86.5% agreement; n = 170 and E-test (85.9% agreement; n = 170. The closest agreement to standard tests was found when testing susceptibility to amphotericin B and echinocandins (88.2 to 91.2% and the least good for the triazoles (79.4 to 82.4%. Furthermore, large datasets on population variation could be rapidly obtained. An analysis of microcolonies revealed subtle effects of antimycotics on resistant strains and below the MIC of sensitive strains, particularly an increase in population heterogeneity and cell density-dependent effects of triazoles. Additionally, the method could be adapted to strain identification via germ tube extension. We suggest PAO culture is a rapid and versatile method that may be usefully adapted to clinical mycology and has research applications.

  4. Analysis of mid-tropospheric space shuttle exhausted aluminum oxide particles

    Science.gov (United States)

    Cofer, Wesley R.; Lala, G. Garland; Wightman, James P.

    Aluminum oxide (Al 2O 3) particles from the exhaust of the space shuttle were collected from the shuttle column cloud immediately after the launch of STS-61A on 30 October 1985. The participates were collected on Teflon filters during a tight descending aircraft spiral maneuver over the altitude interval of 7.6-4.6 km. Scanning electron microscope (SEM) examination of the particles revealed that they were virtually all spherical and ranged in diameter from about 0.1 μm to 10 μm. Particles of < 0.1 μm in diameter were not readily visible in the SEM photomicrographs; however, such particles would not be captured efficiently on the Teflon filters used. Results from energy dispersive analysis by X-ray (EDAX) and electron spectroscopy for chemical analysis (ESCA) confirmed that the particles were predominantly composed of Al and O 2. A particle size distribution was determined from the Al 2O 3 samples. The distribution was bimodal, with one observed peak centered near 2.0 μm. The data indicated the existence of another mode centered at a diameter of < 0.3 μm, but could not be accurately located because our technique cut off at diameters of < 0.1 μm. A mass median diameter of slightly < 2 μm was determined. The collection was evaluated for ice nucleation activity, using the filter technique with a static vapor-diffusion chamber. Only a small fraction (about 1:10 6) of active ice nuclei were determined among the Al 2O 3 particulates.

  5. Fracture mechanical investigations about crack resistance behaviour in non-transforming ceramics in particular aluminum oxide

    International Nuclear Information System (INIS)

    The aim of this work is the clearification of R-curve behaviour of non-transforming ceramics, in particular aluminum oxide exhibiting incrystalline fracture. Investigations of crack growth in controlled bending experiments were performed using 3-Pt- and 4-Pt-bending samples of differing sizes under inert conditions. The fracture experiments were realized using several loading techniques, for example constant and varying displacement rates, load rupture (P = 0) and relaxation tests (v = 0). In addition unloading and reloading experiments were performed to investigate hysteresis curves and residual displacements in accordance with R-curve behaviour. During the crack-growth experiments, the crack extension was measured in situ using a high resolution immersion microscope. With this technique, the fracture processes near the crack tip (crack activity zone) was observed as well. The crack resistance as a function of crack extension (R-curve) was determined using differing calculation methods. All of the methods used resulted in approximately identical R-curves, within the statistical error band. The crack resistance at initiation R0 was 20 N/m. The crack resistance increased during approximately 3 mm of growth to a maximum of 90 N/m. A decrease in the crack resistance was determined for large a/W (crack length normalized with sample height) values, independant of the calculation methods. The R-curve behaviour was interpreted as due to a functional resistance behind the observed crack tip, which arises from a volume dilatation in the crack activity zone while the crack proceeds. (orig.)

  6. Synthesis of aluminum oxide dispersed α-Fe with nano sized grains by simple milling

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, Seung J., E-mail: sjhwang@daejin.ac.kr

    2015-07-25

    Highlights: • Nano-sized α-Fe with Al{sub 2}O{sub 3} dispersoid was produced by milling with elemental powders. • Milled powders were consolidated by Hot pressing and Hot Isostatic Pressing (HIP). • HIPed materials showed a homogeneous distribution of Al{sub 2}O{sub 3} in α-Fe nanocrystalline. • Yield strength of the HIPed materials was as high as 824 MPa. • Most of strengthening contributions are attributed to the Al{sub 2}O{sub 3} dispersoids. - Abstract: Aluminum oxide (with 4 volume% of Al{sub 2}O{sub 3}) dispersed α-Fe (BCC) with nano-sized grain was synthesized by reactive-cryogenic milling with a mixture of the elemental Fe, Al and Fe{sub 3}O{sub 4} (Magnetite) powders as a reactant. Prior to the Hot Isostatic Press (HIP) for further densification of the materials, the milled powders were hot pressed (HPed) at the elevated temperature. The microstructure of the consolidated materials was characterized by standard metallographic techniques such as TEM (Transmission Electron Microscopy), STEM–EDS (Energy Dispersive Spectroscopy), and XRD (X-ray Diffractometer). Mechanical properties of the materials were determined by compressive yield test and micro Vickers hardness test at room temperature. The grain size estimation was attempted for the materials by XRD, using the Scherrer formula and TEM pictures. The microstructure of the materials was comprised with a mixture of a homogeneous distribution of Fe and Al{sub 2}O{sub 3} nano grains. The 0.2% off-set yield strength and micro Vickers hardness of the materials were as high as 824 ± 39 MPa and 3.70 ± 0.1 GPa, respectively.

  7. Atomic layer deposited lithium aluminum oxide: (In)dependency of film properties from pulsing sequence

    Energy Technology Data Exchange (ETDEWEB)

    Miikkulainen, Ville, E-mail: ville.miikkulainen@helsinki.fi; Nilsen, Ola; Fjellvåg, Helmer [Centre for Materials Science and Nanotechnology (SMN), Department of Chemistry, University of Oslo, P.O. Box 1126 Blindern, NO-0318 Oslo (Norway); Li, Han; King, Sean W. [Intel Corporation, 5200 NE Elam Young Parkway, Hillsboro, Oregon 97124 (United States); Laitinen, Mikko; Sajavaara, Timo [Department of Physics, University of Jyväskylä, P.O. Box 35, FI-40014 Jyväskylä (Finland)

    2015-01-01

    Atomic layer deposition (ALD) holds markedly high potential of becoming the enabling method for achieving the three-dimensional all-solid-state thin-film lithium ion battery (LiB). One of the most crucial components in such a battery is the electrolyte that needs to hold both low electronic conductivity and at least fair lithium ion conductivity being at the same time pinhole free. To obtain these desired properties in an electrolyte film, one necessarily has to have a good control over the elemental composition of the deposited material. The present study reports on the properties of ALD lithium aluminum oxide (Li{sub x}Al{sub y}O{sub z}) thin films. In addition to LiB electrolyte applications, Li{sub x}Al{sub y}O{sub z} is also a candidate low dielectric constant (low-k) etch stop and diffusion barrier material in nanoelectronics applications. The Li{sub x}Al{sub y}O{sub z} films were deposited employing trimethylaluminum-O{sub 3} and lithium tert-butoxide-H{sub 2}O for Al{sub 2}O{sub 3} and Li{sub 2}O/LiOH, respectively. The composition was aimed to be controlled by varying the pulsing ratio of those two binary oxide ALD cycles. The films were characterized by several methods for composition, crystallinity and phase, electrical properties, hardness, porosity, and chemical environment. Regardless of the applied pulsing ratio of Al{sub 2}O{sub 3} and Li{sub 2}O/LiOH, all the studied ALD Li{sub x}Al{sub y}O{sub z} films of 200 and 400 nm in thickness were polycrystalline in the orthorhombic β-LiAlO{sub 2} phase and also very similar to each other with respect to composition and other studied properties. The results are discussed in the context of both fundamental ALD chemistry and applicability of the films as thin-film LiB electrolytes and low-k etch stop and diffusion barriers.

  8. Reversible post-breakdown conduction in aluminum oxide-polymer capacitors

    OpenAIRE

    CHEN, Qian; Gomes, HL; Rocha, PRF; De Leeuw,; Meskers, SCJ Stefan

    2013-01-01

    Aluminum/Al2O3/polymer/metal capacitors submitted to a low-power constant current stress undergo dielectric breakdown. The post-breakdown conduction is metastable, and over time the capacitors recover their original insulating properties. The decay of the conduction with time follows a power law (1/t) α . The magnitude of the exponent α can be raised by application of an electric field and lowered to practically zero by optical excitation of the polyspirofluorene polymer. The metastable condu...

  9. Syntheses, structures, and ionic conductivities of perovskite-structured lithium–strontium–aluminum/gallium–tantalum-oxides

    International Nuclear Information System (INIS)

    The ionic conductivities of new perovskite-structured lithium–strontium–aluminum/gallium–tantalum oxides were investigated. Solid solutions of the new perovskite oxides, (LixSr1−x)(Al(1−x)/2Ta(1+x)/2)O3 and (LixSr1−x)(Ga(1−x)/2Ta(1+x)/2)O3, were synthesized using a ball-milled-assisted solid-state method. The partial substitution of the smaller Ga+3 for Ta+5 resulted in new compositions, the structures of which were determined by neutron diffraction measurements using a cubic perovskite structural model with the Pm−3m space group. Vacancies were introduced into the Sr(Li) sites by the formation of solid solutions with compositions (LixSr1−x−y☐y)(Ga[(1−x)/2]−yTa[(1+x)/2]+y)O3, where the composition range of 0≤y≤0.20 was examined for x=0.2 and 0.25. The highest conductivity, 1.85×10−3 S cm−1 at 250 °C, was obtained for (Li0.25Sr0.625☐0.125)(Ga0.25Ta0.75)O3 (x=0.25, y=0.125). Enhanced ionic conductivities were achieved by the introduction of vacancies at the A-sites. - Graphical abstract: Novel lithium-conducting oxides with the cubic perovskite structure (LixSr1−x−y☐y)(Ga[(1−x)/2]−yTa[(1+x)/2]+y)O3 provide a specific solid-solution region with various x and y values, exhibiting the highest ionic conductivity (1.85 S cm−1 at 250 °C) for (Li0.25Sr0.625☐0.125)(Ga0.25Ta0.75)O3 (x=0.25, y=0.125 in (LixSr1−x−y☐y)(Ga[(1−x)/2]−yTa[(1+x)/2]+y)O3). The vacancies (☐) introduced into the A-sites contribute to the enhancement of lithium diffusion in the perovskite structure because of the enlargement of the bottleneck size and suppression of the interaction between lithium and oxygen. - Highlights: • The perovskite-structured novel Li–Sr–Al/Ga–Ta oxides were investigated. • The Ga cation offers a larger bottleneck by increasing the B−O bond length. • The greater conductivity was observed upon Ga-containing perovskite. • The ionic conductivity was improved by the introduction of vacancies into A-site

  10. Syntheses, structures, and ionic conductivities of perovskite-structured lithium–strontium–aluminum/gallium–tantalum-oxides

    Energy Technology Data Exchange (ETDEWEB)

    Phraewphiphat, Thanya, E-mail: thanya@echem.titech.ac.jp [Department of Electronic Chemistry, Interdisciplinary Graduate School of Science and Engineering, Tokyo Institute of Technology, 4259 Nagatsuta, Midori, Yokohama 226-8502 (Japan); Iqbal, Muhammad, E-mail: iqbal@echem.titech.ac.jp [Department of Electronic Chemistry, Interdisciplinary Graduate School of Science and Engineering, Tokyo Institute of Technology, 4259 Nagatsuta, Midori, Yokohama 226-8502 (Japan); Suzuki, Kota, E-mail: ksuzuki@echem.titech.ac.jp [Department of Electronic Chemistry, Interdisciplinary Graduate School of Science and Engineering, Tokyo Institute of Technology, 4259 Nagatsuta, Midori, Yokohama 226-8502 (Japan); Matsuda, Yasuaki, E-mail: matsuda@chem.mie-u.ac.jp [Department of Chemistry, Mie University, 1577 Kurimamachiyacho, Tsu, Mie 514-8507 (Japan); Yonemura, Masao, E-mail: masao.yonemura@kek.jp [High Energy Accelerator Research Organization, Tokai-mura, Naka-gun, Ibaraki 319-1106 (Japan); Hirayama, Masaaki, E-mail: hirayama@echem.titech.ac.jp [Department of Electronic Chemistry, Interdisciplinary Graduate School of Science and Engineering, Tokyo Institute of Technology, 4259 Nagatsuta, Midori, Yokohama 226-8502 (Japan); Kanno, Ryoji, E-mail: kanno@echem.titech.ac.jp [Department of Electronic Chemistry, Interdisciplinary Graduate School of Science and Engineering, Tokyo Institute of Technology, 4259 Nagatsuta, Midori, Yokohama 226-8502 (Japan)

    2015-05-15

    The ionic conductivities of new perovskite-structured lithium–strontium–aluminum/gallium–tantalum oxides were investigated. Solid solutions of the new perovskite oxides, (Li{sub x}Sr{sub 1−x})(Al{sub (1−x)/2}Ta{sub (1+x)/2})O{sub 3} and (Li{sub x}Sr{sub 1−x})(Ga{sub (1−x)/2}Ta{sub (1+x)/2})O{sub 3}, were synthesized using a ball-milled-assisted solid-state method. The partial substitution of the smaller Ga{sup +3} for Ta{sup +5} resulted in new compositions, the structures of which were determined by neutron diffraction measurements using a cubic perovskite structural model with the Pm−3m space group. Vacancies were introduced into the Sr(Li) sites by the formation of solid solutions with compositions (Li{sub x}Sr{sub 1−x−y}☐{sub y})(Ga{sub [(1−x)/2]−y}Ta{sub [(1+x)/2]+y})O{sub 3}, where the composition range of 0≤y≤0.20 was examined for x=0.2 and 0.25. The highest conductivity, 1.85×10{sup −3} S cm{sup −1} at 250 °C, was obtained for (Li{sub 0.25}Sr{sub 0.625}☐{sub 0.125})(Ga{sub 0.25}Ta{sub 0.75})O{sub 3} (x=0.25, y=0.125). Enhanced ionic conductivities were achieved by the introduction of vacancies at the A-sites. - Graphical abstract: Novel lithium-conducting oxides with the cubic perovskite structure (Li{sub x}Sr{sub 1−x−y}☐{sub y})(Ga{sub [(1−x)/2]−y}Ta{sub [(1+x)/2]+y})O{sub 3} provide a specific solid-solution region with various x and y values, exhibiting the highest ionic conductivity (1.85 S cm{sup −1} at 250 °C) for (Li{sub 0.25}Sr{sub 0.625}☐{sub 0.125})(Ga{sub 0.25}Ta{sub 0.75})O{sub 3} (x=0.25, y=0.125 in (Li{sub x}Sr{sub 1−x−y}☐{sub y})(Ga{sub [(1−x)/2]−y}Ta{sub [(1+x)/2]+y})O{sub 3}). The vacancies (☐) introduced into the A-sites contribute to the enhancement of lithium diffusion in the perovskite structure because of the enlargement of the bottleneck size and suppression of the interaction between lithium and oxygen. - Highlights: • The perovskite-structured novel Li

  11. A colorimetric sensor based on anodized aluminum oxide (AAO) substrate for the detection of nitroaromatics.

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Y.; Wang, H. H.; Indacochea, J. E.; Wang, M. L. (Materials Science Division); (Northeastern Univ.); (Univ. of Illinois at Chicago)

    2011-12-15

    Simple and low cost colorimetric sensors for explosives detection were explored and developed. Anodized aluminum oxide (AAO) with large surface area through its porous structure and light background color was utilized as the substrate for colorimetric sensors. Fabricated thin AAO films with thickness less than {approx} 500 nm allowed us to observe interference colors which were used as the background color for colorimetric detection. AAO thin films with various thickness and pore-to-pore distance were prepared through anodizing aluminum foils at different voltages and times in dilute sulfuric acid. Various interference colors were observed on these samples due to their difference in structures. Accordingly, suitable anodization conditions that produce AAO samples with desired light background colors for optical applications were obtained. Thin film interference model was applied to analyze the UV-vis reflectance spectra and to estimate the thickness of the AAO membranes. We found that the thickness of produced AAO films increased linearly with anodization time in sulfuric acid. In addition, the growth rate was higher for AAO anodized using higher voltages. The thin film interference formulism was further validated with a well established layer by layer deposition technique. Coating poly(styrene sulfonate) sodium salt (PSS) and poly(allylamine hydrochloride) (PAH) layer by layer on AAO thin film consistently shifted its surface color toward red due to the increase in thickness. The red shift of UV-vis reflectance was correlated quantitatively to the number of layers been assembled. This sensitive red shift due to molecular attachment (increase in thickness) on AAO substrate was applied toward nitroaromatics detection. Aminopropyltrimethoxysilane (APTS) which can be attached onto AAO nanowells covalently through silanization and attract TNT molecules was coated and applied for TNT detection. UV-vis spectra of AAO with APTS shifted to the longer wavelength side due to

  12. Sol-gel deposition and plasma treatment of intrinsic, aluminum-doped, and gallium-doped zinc oxide thin films as transparent conductive electrodes

    Science.gov (United States)

    Zhu, Zhaozhao; Mankowski, Trent; Balakrishnan, Kaushik; Shikoh, Ali Sehpar; Touati, Farid; Benammar, Mohieddine A.; Mansuripur, Masud; Falco, Charles M.

    2015-09-01

    Zinc oxide and aluminum/gallium-doped zinc oxide thin films were deposited via sol-gel spin-coating technique. Employing plasma treatment as alternative to post thermal annealing, we found that the morphologies of these thin films have changed and the sheet resistances have been significantly enhanced. These plasma-treated thin films also show very good optical properties, with transmittance above 90% averaged over the visible wavelength range. Our best aluminum/gallium-doped zinc oxide thin films exhibit sheet resistances (Rs) of ~ 200 Ω/sq and ~ 150 Ω/sq, respectively.

  13. Comparison of the kinetic laws of the dissolution of bauxite and aluminum and iron(III) oxides and hydroxides in hydrochloric acid

    Science.gov (United States)

    Gololobova, E. G.; Gorichev, I. G.; Lainer, Yu. A.; Kozlov, K. V.

    2013-07-01

    The influence of the temperature and concentration of a hydrochloric acid solution on the dissolution kinetics of aluminum and iron(III) oxides and hydroxides and a natural sample of aluminum-containing raw materials, bauxite, is studied. The rate W of the transition of iron(III) ions from bauxite is higher than the rate of aluminum ion transition. The dependence of the fraction of a dissolved solid phase on time τ of dissolution of the oxides and hydroxides is determined, α = 1 — exp(- Asinh( Wτ)). The solubility of iron(III) chloride increases and that of aluminum chloride decreases as the HCl concentration increases. An empirical equation is proposed for the description of the dependence of the process rate on a series of parameters,.

  14. Effecting Factors on Thickness of Oxide Aluminum Membrane%多孔阳极氧化铝膜厚度影响因素

    Institute of Scientific and Technical Information of China (English)

    王晓燕; 翟秀静; 张延安; 符岩; 郑双

    2011-01-01

    以H2SO4为电解液对高纯铝箔进行阳极氧化,用涡流测厚仪分析制备工艺参数对多孔氧化铝膜厚度的影响.结果表明,在一定电解液浓度及电解电压下,氧化铝膜厚度随电解液浓度及电解电压的增加而增大,但过高的电解液浓度及电解电压均会造成氧化铝膜的快速击穿.氧化铝膜厚度随电解时间的增加而增大,但初期的增长速度较快,后期随电解时间的增加变化缓慢.在一定温度范围内氧化铝膜的厚度随温度的升高而增加.%High-pure aluminum foil is oxidized in anodic with H2SO4 as electrolyte. The effect of the technological parameters on thickness of oxide aluminum membrane is investigated by using eddy current sensor thickness. The results show that the thickness of oxide aluminum membrane is increased with the increase of electrolyte concentration and voltage, but the exorbitant electrolyte concentration and electrolysis voltage are prone to rapid breakdown of aluminum foil. The thickness of oxide aluminum membrane is increased with the increase of the electrolysis time, however the growth speed of oxide aluminum membrane thickness is firstly fast and then becomes slow. Within a certain range of temperature, the thickness of oxide aluminum membrane is increased with the increase of the electrolysis temperature.

  15. Structural, Optical, and Dielectric Properties of Aluminum Oxide Nanofibers Synthesized by a Lower-Temperature Sol-Gel Approach

    Science.gov (United States)

    Riaz, Saira; Sajid-ur-Rehman; Abutalib, Mymona; Naseem, Shahzad

    2016-07-01

    Alumina (Al2O3) is the most versatile and important ceramic material, having applications in various fields including electronic devices. It is stable at high temperatures and is chemically inert. The sol-gel method, a relatively lower-temperature technique, has been used to synthesize aluminum oxide nanofibers. The molarity of the sol concentration was varied as 0.7 M, 0.8 M, 0.9 M, 1.0 M, and 1.1 M. The structural, optical, and dielectric properties of the as-synthesized nanofibers were characterized. x-ray diffraction (XRD) analysis results confirmed formation of α-Al2O3 phase of aluminum oxide, notably without any heat treatment or use of water as solvent. The crystallite size and unit cell volume of the nanofibers increased as the sol concentration was increased to 0.9 M, but further increase in sol concentration resulted in reduction of crystallite size and increase in dislocations. Scanning electron microscopy (SEM) results revealed uniform distribution of nanofibers (˜25 nm to 30 nm) under all conditions. Nanofibers prepared using sol concentration of 0.9 M showed high transmission (˜89%) in the visible and infrared regions. The energy bandgap varied from 3.69 eV to 4.1 eV with the variation in molar concentration. Lower bandgap correlated with defect-induced states in the bandgap. The high refractive index is indicative of high density of aluminum oxide nanofibers. High grain-boundary resistance (1.455 MΩ) and high dielectric constant (˜15.76) along with low tangent loss were observed at molar concentration of 0.9 M.

  16. Hybrid aluminum and indium conducting filaments for nonpolar resistive switching of Al/AlOx/indium tin oxide flexible device

    Science.gov (United States)

    Yuan, Fang; Wang, Jer-Chyi; Zhang, Zhigang; Ye, Yu-Ren; Pan, Liyang; Xu, Jun; Lai, Chao-Sung

    2014-02-01

    The nonpolar resistive switching characteristics of an Al/AlOx/indium tin oxide (ITO) device on a plastic flexible substrate are investigated. By analyzing the electron diffraction spectroscopy results and thermal coefficient of resistivity, it is discovered that the formation of aluminum and indium conducting filaments in AlOx film strongly depends on the polarity of the applied voltage. The metal ions arising from the Al and ITO electrodes respectively govern the resistive switching in corresponding operation polarity. After 104 times of mechanical bending, the device can perform satisfactorily in terms of resistance distribution, read sequence of high and low resistive states, and thermal retention properties.

  17. Multi-electrolyte-step anodic aluminum oxide method for the fabrication of self-organized nanochannel arrays

    Science.gov (United States)

    2012-01-01

    Nanochannel arrays were fabricated by the self-organized multi-electrolyte-step anodic aluminum oxide [AAO] method in this study. The anodization conditions used in the multi-electrolyte-step AAO method included a phosphoric acid solution as the electrolyte and an applied high voltage. There was a change in the phosphoric acid by the oxalic acid solution as the electrolyte and the applied low voltage. This method was used to produce self-organized nanochannel arrays with good regularity and circularity, meaning less power loss and processing time than with the multi-step AAO method. PMID:22333268

  18. Gas-Phase Partial Oxidation of Lignin to Carboxylic Acids over Vanadium Pyrophosphate and Aluminum-Vanadium-Molybdenum.

    Science.gov (United States)

    Lotfi, Samira; Boffito, Daria C; Patience, Gregory S

    2015-10-26

    Lignin is a complex polymer that is a potential feedstock for aromatic compounds and carboxylic acids by cleaving the β-O-4 and 5-5' linkages. In this work, a syringe pump atomizes an alkaline solution of lignin into a catalytic fluidized bed operating above 600 K. The vanadium heterogeneous catalysts convert all the lignin into carboxylic acids (up to 25 % selectivity), coke, carbon oxides, and hydrogen. Aluminum-vanadium-molybdenum mostly produced lactic acid (together with formic acid, acrylic acid, and maleic anhydride), whereas the vanadium pyrophosphate catalyst produced more maleic anhydride. PMID:26361086

  19. Fabrication and applications of nanocomposite structures using anodized aluminum oxide membranes

    Science.gov (United States)

    Gapin, Andrew Isaac

    As the field of nanotechnology continues to advance and device feature sizes scale down to ever smaller dimensions, it is becoming increasingly important to develop quick and efficient methods for large-scale production at the nanoscale. Creating such a template would have widespread uses in areas such as magnetic data storage, chemical sensors, and mask technology. One promising approach to realizing this goal may lie in utilizing the self-ordering behavior found in porous anodized aluminum oxide (AAO). This material offers many advantages such as the ability to customize the pore diameter and spacing and easy device integration based on its compatibility with silicon substrates. The pores of the AAO templates can be filled with many different materials via electrochemical deposition or other methods to produce numerous potential devices. In this work, current research results detailing the fabrication of AAO templates and their use in creating ˜100 nm tall CoPt, Ni, and composite Ni/CoPt nanowires is demonstrated. The synthesis of such nanostructures may ultimately be advantageous for new types of patterned magnetic recording media. The Ni nanowires exhibit relatively soft magnetic coercivity of 242 Oe, while the CoPt nanowires show a very high coercivity of at least 10.97 kOe, measured in the perpendicular direction along the nanowires axis. The composite soft magnet/hard magnet Ni/CoPt nanowires exhibit intermediate perpendicular coercivities depending on the relative amounts of Ni and CoPt. The Ni 80nm/CoPt20nm nanowires showed a coercivity of 1.96 kOe, the Ni50nm/CoPt50nm nanowires had a coercivity of 3.59 kOe, and the Ni20nm/CoPt80nm nanowires had a coercivity of 5.10 kOe. This marked decrease in the coercivity is significant because it could facilitate easier magnetic data writing. Analysis of the magnetic properties of the various nanowire structures and their dependence on the processing parameters is presented. A method for utilizing the AAO structure

  20. Highly flexible transparent thin film heaters based on silver nanowires and aluminum zinc oxides

    Energy Technology Data Exchange (ETDEWEB)

    Cheong, Hahn-Gil; Kim, Jin-Hoon; Song, Jun-Hyuk; Jeong, Unyong; Park, Jin-Woo, E-mail: jwpark09@yonsei.ac.kr

    2015-08-31

    In this work, we developed highly flexible transparent film heaters (f-TFHs) composed of Ag nanowire networks (AgNWs) and aluminum zinc oxide (AZO). Uniform AgNWs were roll-to-roll coated on polyethylene terephthalate (PET) substrates using the Mayer rod method, and AZO was sputter-deposited atop the AgNWs at room temperature. The sheet resistance (R{sub s}) and transparency (T{sub opt}) of the AZO-coated AgNWs changed only slightly compared with the uncoated AgNWs. AZO is thermally less conductive than the heat pipes, but increases the thermal efficiency of the heaters blocking the heat convection through the air. Based on Joule heating, a higher average film temperature (T{sub ave}) is attained at a fixed electric potential drop between electrodes (ϕ) as the R{sub s} of the film decreases. Our experimental results revealed that T{sub ave} of the hybrid f-TFH is higher than AgNWs when the ratio of the area coverage of AgNWs to AZO is over a certain value. When a ϕ as low as 3 V/cm was applied to 5 cm × 5 cm f-TFHs, the maximum temperature of the hybrid film was over 100 °C, which is greater than that of AgNWs by more than 30 °C. Furthermore, uniform heating throughout the surfaces is achieved in the hybrid films while heating begins in small areas where densities of the nanowires (NWs) are the highest in the bare network. The non-uniform heating decreases the lifetime of f-TFHs by forming hot spots. Cyclic bending test results indicated that the hybrid films were as flexible as the AgNWs, and the R{sub s} of the hybrid films changes only slightly until 5000 cycles. Combined with the high-throughput coating technology presented here, the hybrid films will provide a robust and scalable strategy for large-area f-TFHs with highly enhanced performance. - Highlights: • We developed highly efficient flexible thin film heaters based on Ag nanowires and AZO composites. • In the composite, AZO plays an important role as an insulation blanket to block heat loss to

  1. Preparation of aluminum doped zinc oxide films and the study of their microstructure, electrical and optical properties

    International Nuclear Information System (INIS)

    Aluminum doped zinc oxide (AZO) polycrystalline thin films were prepared by sol-gel dip-coating process on optical glass substrates. Zinc acetate solutions of 0.5 M in isopropanol stabilized by diethanolamine and doped with a concentrated solution of aluminum nitrate in ethanol were used. The content of aluminum in the sol was varied from 1 to 3 at.%. Crystalline ZnO thin films were obtained following an annealing process at temperatures between 300 deg. C and 500 deg. C for 1 h. The coatings have been characterized by X-ray diffraction, UV-Visible spectrophotometry, scanning electron microscopy, and electrical resistance measurement. The ZnO:Al thin films are transparent (∼ 90%) in near ultraviolet and visible regions. With the annealing temperature increasing from 300 deg. C to 500 deg. C, the film was oriented more preferentially along the (0 0 2) direction, the grain size of the film increased, the transmittance also became higher and the electrical resistivity decreased. The X-ray diffraction analysis revealed single-phase ZnO hexagonal wurtzite structure. The best conductors were obtained for the AZO films containing 1 at.% of Al, annealed at 500 deg. C, 780 nm film thickness

  2. Pulmonary fibrosis in aluminum oxide workers. Investigation of nine workers, with pathologic examination and microanalysis in three of them

    International Nuclear Information System (INIS)

    Epidemiologic surveys have indicated an excess of nonmalignant respiratory disease in workers exposed to aluminum oxide (Al2O3) during abrasives production. However, clinical, roentgenographic, histologic, and microanalytic description of these workers are lacking. This is a report of nine Al2O3-exposed workers with abnormal chest roentgenograms (profusion greater than or equal to 1/0, ILO/UC) from a plant engaged in the production of Al2O3 abrasives from alundum ore. Mean duration of exposure was 25 yr, and time since first exposure was 28 yr. in a subgroup of three, the severity of symptoms, reduction in the forced vital capacity (67% predicted) and diffusing capacity (51% predicted), and progressive roentgenographic changes (profusion greater than or equal to 2/2) prompted open lung biopsy. Lung tissue was analyzed by scanning electron microscopy and electron microprobe analysis. In each of the three biopsies, interstitial fibrosis with honeycombing was seen on routine section. In one biopsy, silica and asbestos fiber counts were at the low end of the range seen with silicosis and asbestosis; however, the absence of asbestos bodies and silicotic nodules suggested that the fibrosis was due to another cause. Metals occurred in amounts several orders of magnitude above background, and the majority was aluminum as Al2O3 and aluminum alloys. The findings in these nine workers suggests a common exposure as the possible cause. The nonspecific pathologic findings, absence of asbestos bodies and silicotic nodules, and the striking number of aluminum-containing particles suggest that Al2O3 is that common exposure. The possibility of mixed dust fibrosis should also be considered

  3. Cerium oxide coated anodes for aluminum electrowinning: Topical report, October 1, 1986-June 30, 1987

    Energy Technology Data Exchange (ETDEWEB)

    Walker, J. K.

    1987-12-01

    Because of the cost of building and maintaining a carbon anode plant and the energy penalties associated with the use of carbon anodes in the production of aluminum, the use of inert anodes has long been proposed. Various cermet anodes have been investigated. In this paper, tests on a material, cerium oxyfluoride (CEROX), deposited in situ as an anode, are reported. (JDH)

  4. Enhancement of barrier properties of aluminum oxide layer by optimization of plasma-enhanced atomic layer deposition process

    International Nuclear Information System (INIS)

    Aluminum oxide (AlxOy) layers were deposited on polyethylene naphthalate substrates by low frequency plasma-enhanced atomic layer deposition process for barrier property enhancement. Trimethylaluminum and oxygen plasma were used as precursor and reactant materials, respectively. In order to enhance the barrier properties several process parameters were examined such as plasma power, working pressure and electrode–substrate distance. Increase of plasma power enhanced the reactivity of activated atomic and molecular oxygen to reduce the carbon contents in AlxOy layer, which appeared to enhance the barrier properties. But too high power caused generation of byproducts which were reincorporated in AlxOy layer to reduce the barrier properties. Plasma generated at lower working pressure was provided with an additional energy for reactions and had more diffusion of the plasma. The O/Al ratio of the layer approached the stoichiometric value by increasing the electrode–substrate distance. At the following conditions: 300 W of plasma power, 26.7 Pa of working pressure and 50 mm of electrode–substrate distance, water vapor transmission rates of the AlxOy layer reached 8.85 × 10−4 g/m2 day. - Highlights: • Aluminum oxide layer was well formed by plasma enhanced atomic layer deposition. • Process parameters were optimized to enhance the barrier properties. • Barrier coating of plastic substrate can be applied to flexible display devices

  5. Aluminum-doped zinc oxide nanoparticles attenuate the TSLP levels via suppressing caspase-1 in activated mast cells.

    Science.gov (United States)

    Kim, Min-Ho; Seo, Jun-Ho; Kim, Hyung-Min; Jeong, Hyun-Ja

    2016-04-01

    Zinc oxide nanoparticles (ZO-NPs) are used as antimicrobials, anti-inflammatories, and to treat cancer. However, although ZO-NPs have excellent efficiency and specificity, their cytotoxicity is higher than that of micron-sized zinc oxide. Doping ZO-NPs with aluminum can improve therapeutic efficacy, but the biological effects and mechanisms involved have not been elucidated. Here, we reported the efficacy of aluminum-doped ZO-NP (AZO) on thymic stromal lymphopoietin (TSLP) production and caspase-1 activation in human mast cell line, HMC-1 cells. AZO significantly reduced TSLP levels as well as interleukin (IL)-6, IL-8, and tumor necrosis factor (TNF)-α without inducing cytotoxicity. Furthermore, AZO more effectively reduced TSLP, IL-6, IL-8, and TNF-α levels than ZO-NP. The levels of inflammatory cytokine mRNA were also reduced by AZO treatment. AZO blocked production of IL-1β and activations of caspase-1 and nuclear factor-κB by inhibiting IκB kinase β and receptor interacting protein 2. In addition, AZO attenuated phosphorylation of mitogen-activated protein kinases, such as extracellular signal-regulated kinase, c-Jun N-terminal kinases, and p38. These findings provide evidence that AZO improves anti-inflammatory properties and offer a safe and effective potential treatment option. PMID:26825457

  6. Comprehensive study and design of scaled metal/high-k/Ge gate stacks with ultrathin aluminum oxide interlayers

    Energy Technology Data Exchange (ETDEWEB)

    Asahara, Ryohei; Hideshima, Iori; Oka, Hiroshi; Minoura, Yuya; Hosoi, Takuji, E-mail: hosoi@mls.eng.osaka-u.ac.jp; Shimura, Takayoshi; Watanabe, Heiji [Graduate School of Engineering, Osaka University, 2-1 Yamadaoka, Suita, Osaka 565-0871 (Japan); Ogawa, Shingo [Graduate School of Engineering, Osaka University, 2-1 Yamadaoka, Suita, Osaka 565-0871 (Japan); Toray Research Center Inc., 3-3-7 Sonoyama, Otsu, Shiga 520-8567 (Japan); Yoshigoe, Akitaka; Teraoka, Yuden [Japan Atomic Energy Agency, 1-1-1 Kouto, Sayo-cho, Sayo-gun, Hyogo 679-5148 (Japan)

    2015-06-08

    Advanced metal/high-k/Ge gate stacks with a sub-nm equivalent oxide thickness (EOT) and improved interface properties were demonstrated by controlling interface reactions using ultrathin aluminum oxide (AlO{sub x}) interlayers. A step-by-step in situ procedure by deposition of AlO{sub x} and hafnium oxide (HfO{sub x}) layers on Ge and subsequent plasma oxidation was conducted to fabricate Pt/HfO{sub 2}/AlO{sub x}/GeO{sub x}/Ge stacked structures. Comprehensive study by means of physical and electrical characterizations revealed distinct impacts of AlO{sub x} interlayers, plasma oxidation, and metal electrodes serving as capping layers on EOT scaling, improved interface quality, and thermal stability of the stacks. Aggressive EOT scaling down to 0.56 nm and very low interface state density of 2.4 × 10{sup 11 }cm{sup −2}eV{sup −1} with a sub-nm EOT and sufficient thermal stability were achieved by systematic process optimization.

  7. Electrically conductive anodized aluminum coatings

    Science.gov (United States)

    Alwitt, Robert S. (Inventor); Liu, Yanming (Inventor)

    2001-01-01

    A process for producing anodized aluminum with enhanced electrical conductivity, comprising anodic oxidation of aluminum alloy substrate, electrolytic deposition of a small amount of metal into the pores of the anodized aluminum, and electrolytic anodic deposition of an electrically conductive oxide, including manganese dioxide, into the pores containing the metal deposit; and the product produced by the process.

  8. Fabrication and applications of nanocomposite structures using anodized aluminum oxide membranes

    OpenAIRE

    Gapin, Andrew Isaac

    2007-01-01

    As the field of nanotechnology continues to advance and device feature sizes scale down to ever smaller dimensions, it is becoming increasingly important to develop quick and efficient methods for large-scale production at the nanoscale. Creating such a template would have widespread uses in areas such as magnetic data storage, chemical sensors, and mask technology. One promising approach to realizing this goal may lie in utilizing the self-ordering behavior found in porous anodized aluminum ...

  9. Structure and formation mechanism of rolled-in oxide areas on aluminum lithographic printing sheets

    International Nuclear Information System (INIS)

    The subsurface area introduced during rolling on the 1100 aluminum alloy series alters its surface properties, which makes it more susceptible to corrosion. A combination of different transmission electron microscopy techniques is employed to observe the orientation of small grain structures and the distribution elements in the subsurface layer. This approach provided valuable insight into the formation mechanism of the layer and the phenomena taking place during rolling.

  10. Effects of temperature and voltage mode on nanoporous anodic aluminum oxide films by one-step anodization

    International Nuclear Information System (INIS)

    Many conventional anodic aluminum oxide (AAO) templates were performed using two-step direct current anodization (DCA) at low temperature (0–5 °C) to avoid dissolution effects. This process is relatively complex. Pulse anodization (PA) by switching between high and low voltages has been used to improve wear resistance and corrosion resistance in barrier type anodic oxidation of aluminum or hard anodization for current nanotechnology. However, there are only few investigations of AAO by hybrid pulse anodization (HPA) with normal-positive and small-negative voltages, especially for the one-step anodization, to shorten the running time. In this article, the effects of temperature and voltage modes (DCA vs. HPA) on one-step anodization have been investigated. The porous AAO films were fabricated using one-step anodization in 0.5 M oxalic acid in different voltage modes including the HPA and DCA and the environment temperature were varied at 5–15 °C. The morphology, pore size and oxide thickness of AAO films were characterized by high resolution field emission scanning electron microscope. The pore size distribution and circularity of AAO films can be quantitatively analyzed by image processing of SEM. The pore distribution uniformity and circularity of AAO by HPA is much better than DCA due to its effective cooling at relatively high temperatures. On the other hand, increasing environment temperature can increase the growth rate and enlarge the pore size of AAO films. The results of one-step anodization by hybrid pulse could promote the AAO quality and provide a simple and convenient fabrication compared to DCA.

  11. Highly Transparent and Flexible Triboelectric Nanogenerators with Subwavelength-Architectured Polydimethylsiloxane by a Nanoporous Anodic Aluminum Oxide Template.

    Science.gov (United States)

    Dudem, Bhaskar; Ko, Yeong Hwan; Leem, Jung Woo; Lee, Soo Hyun; Yu, Jae Su

    2015-09-23

    Highly transparent and flexible triboelectric nanogenerators (TENGs) were fabricated using the subwavelength-architectured (SWA) polydimethylsiloxane (PDMS) with a nanoporous anodic aluminum oxide (AAO) template as a replica mold. The SWA PDMS could be utilized as a multifunctional film for a triboelectric layer, an antireflection coating, and a self-cleaning surface. The nanopore arrays of AAO were formed by a simple, fast, and cost-effective electrochemical oxidation process of aluminum, which is relatively impressive for fabrication of the TENG device. For electrical contacts, the SWA PDMS was laminated on the indium tin oxide (ITO)-coated polyethylene terephthalate (PET) as a bottom electrode, and the bare ITO-coated PET (i.e., ITO/PET) was used for the top electrode. Compared to the ITO/PET, the SWA PDMS on the ITO/PET improved the transmittance from 80.5 to 83% in the visible wavelength region and also had high transmittances of >85% at wavelengths of 430-455 nm. The SWA PDMS also exhibited the hydrophobic surface with a water contact angle (θCA) of ∼115°, which can be useful for self-cleaning applications. The average transmittance (Tavg) of the entire TENG device was observed to be ∼70% over a broad wavelength range. At an external pushing frequency of 0.5 Hz, for the TENG device with the ITO top electrode, open-circuit voltage (VOC) and short-circuit current (ISC) values of ∼3.8 V and ∼0.8 μA were obtained instantaneously, respectively, which were higher than those (i.e., VOC ≈ 2.2 V, and ISC ≈ 0.4 μA) of the TENG device with a gold top electrode. The effect of external pushing force and frequency on the output device performance of the TENGs was investigated, including the device robustness. A theoretical optical analysis of SWA PDMS was also performed. PMID:26301328

  12. Adsorption of carbon monoxide on small aluminum oxide clusters: Role of the local atomic environment and charge state on the oxidation of the CO molecule

    International Nuclear Information System (INIS)

    We present extensive density functional theory (DFT) calculations dedicated to analyze the adsorption behavior of CO molecules on small AlxOy± clusters. Following the experimental results of Johnson et al. [J. Phys. Chem. A 112, 4732 (2008)], we consider structures having the bulk composition Al2O3, as well as smaller Al2O2 and Al2O units. Our electron affinity and total energy calculations are consistent with aluminum oxide clusters having two-dimensional rhombus-like structures. In addition, interconversion energy barriers between two- and one-dimensional atomic arrays are of the order of 1 eV, thus clearly defining the preferred isomers. Single CO adsorption on our charged AlxOy± clusters exhibits, in general, spontaneous oxygen transfer events leading to the production of CO2 in line with the experimental data. However, CO can also bind to both Al and O atoms of the clusters forming aluminum oxide complexes with a CO2 subunit. The vibrational spectra of AlxOy + CO2 provides well defined finger prints that may allow the identification of specific isomers. The AlxOy+ clusters are more reactive than the anionic species and the final Al2O+ + CO reaction can result in the production of atomic Al and carbon dioxide as observed from experiments. We underline the crucial role played by the local atomic environment, charge density distribution, and spin-multiplicity on the oxidation behavior of CO molecules. Finally, we analyze the importance of coadsorption and finite temperature effects by performing DFT Born-Oppenheimer molecular dynamics. Our calculations show that CO oxidation on AlxOy+ clusters can be also promoted by the binding of additional CO species at 300 K, revealing the existence of fragmentation processes in line with the ones experimentally inferred

  13. Aluminum powder metallurgy processing

    Energy Technology Data Exchange (ETDEWEB)

    Flumerfelt, J.F.

    1999-02-12

    The objective of this dissertation is to explore the hypothesis that there is a strong linkage between gas atomization processing conditions, as-atomized aluminum powder characteristics, and the consolidation methodology required to make components from aluminum powder. The hypothesis was tested with pure aluminum powders produced by commercial air atomization, commercial inert gas atomization, and gas atomization reaction synthesis (GARS). A comparison of the GARS aluminum powders with the commercial aluminum powders showed the former to exhibit superior powder characteristics. The powders were compared in terms of size and shape, bulk chemistry, surface oxide chemistry and structure, and oxide film thickness. Minimum explosive concentration measurements assessed the dependence of explosibility hazard on surface area, oxide film thickness, and gas atomization processing conditions. The GARS aluminum powders were exposed to different relative humidity levels, demonstrating the effect of atmospheric conditions on post-atomization processing conditions. The GARS aluminum powders were exposed to different relative humidity levels, demonstrating the effect of atmospheric conditions on post-atomization oxidation of aluminum powder. An Al-Ti-Y GARS alloy exposed in ambient air at different temperatures revealed the effect of reactive alloy elements on post-atomization powder oxidation. The pure aluminum powders were consolidated by two different routes, a conventional consolidation process for fabricating aerospace components with aluminum powder and a proposed alternative. The consolidation procedures were compared by evaluating the consolidated microstructures and the corresponding mechanical properties. A low temperature solid state sintering experiment demonstrated that tap densified GARS aluminum powders can form sintering necks between contacting powder particles, unlike the total resistance to sintering of commercial air atomization aluminum powder.

  14. Fabrication of a Ni nano-imprint stamp for an anti-reflective layer using an anodic aluminum oxide template.

    Science.gov (United States)

    Park, Eun-Mi; Lim, Seung-Kyu; Ra, Senug-Hyun; Suh, Su-Jung

    2013-11-01

    Aluminum anodizing can alter pore diameter, density distribution, periodicity and layer thickness in a controlled way. Because of this property, porous type anodic aluminum oxide (AAO) was used as a template for nano-structure fabrication. The alumina layer generated at a constant voltage increased the pore size from 120 nm to 205 nm according to an increasing process time from 60 min to 150 min. The resulting fabricated AAO templates had pore diameters at or less than 200 nm. Ni was sputtered as a conductive layer onto this AAO template and electroplated using DC and pulse power. Comparing these Ni stamps, those generated from electroplating using on/reverse/off pulsing had an ordered pillar array and maintained the AAO template morphology. This stamp was used for nano-imprinting on UV curable resin coated glass wafer. Surface observations via electron microscopy showed that the nano-imprinted patterned had the same shape as the AAO template. A soft mold was subsequently fabricated and nano-imprinted to form a moth-eye structure on the glass wafer. An analysis of the substrate transmittance using UV-VIS/NIR spectroscopy showed that the transmittance of the substrate with the moth-eye structure was 5% greater that the non-patterned substrate. PMID:24245297

  15. Effects of Surface Nitrification on Thermal Conductivity of Modified Aluminum Oxide Nanofibers-Reinforced Epoxy Matrix Nanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Byungjoo; Bae, Kyongmin; An, Kayhyeok [Jeonju Institute of Machinery and Carbon Composites, Jeonju (Korea, Republic of); Park, Soojin [Inha University, Incheon (Korea, Republic of)

    2012-10-15

    Aluminum oxide (Al{sub 2}O{sub 3}) nanofibers were treated thermally under an ammonia (NH{sub 3}) gas stream balanced by nitrogen to form a thin aluminum nitride (AlN) layer on the nanofibers, resulting in the enhancement of thermal conductivity of Al{sub 2}O{sub 3}/epoxy nanocomposites. The micro-structural and morphological properties of the NH{sub 3}-assisted thermally-treated Al{sub 2}O{sub 3} nanofibers were characterized by X-ray diffraction (XRD) and atomic force microscopy (AEM), respectively. The surface characteristics and pore structures were observed by X-ray photoelectron spectroscopy (XPS), Zeta-potential and N{sub 2}/77 K isothermal adsorptions. From the results, the formation of AlN on Al{sub 2}O{sub 3} nanofibers was confirmed by XRD and XPS. The thermal conductivity (TC) of the modified Al{sub 2}O{sub 3} nanofibers/epoxy composites increased with increasing treated temperatures. On the other hand, the severely treated Al{sub 2}O{sub 3}/epoxy composites showed a decrease in TC, resulting from a decrease in the probability of heat-transfer networks between the filler and matrix in this system due to the aggregation of nanofiber fillers.

  16. Analysis of Intermetallic Phases Formed on Surface Vapor Oxidized H13 Hot Work Steels in Molten Aluminum

    Institute of Scientific and Technical Information of China (English)

    WANGRong; WUXiao-chun; MINYong-an

    2004-01-01

    In this paper, the author dipped surface vapor oxidized H13 steel specimens into 700℃ molten aluminum liquid for a certain period of time. Analyze the intermetallic phases formed on the H 13 samples surface with optical microscope and X-ray diffraction method. The observation of immersion test sample's cross-section shows that Fe304 film will protect die substrate from molten aluminum erosion. The identification of the intermetallic phases reveals that they consist of 2 parts, which is named as the composite layer and the compact layer. Further investigations are made in order to know the phase constituents of the 2 layers, they are Al8Fe2Si (outer composite layer), (AlCuMg) and Al5Fe2 (compact layer), respectively. The experimental results show that on the same specimen, a convex surface with bigger radius of curvature is more likely to be molten and the melting loss speed is also faster than a flat and smooth surface. The thickness of compact layer on a smooth surface is much bigger than that of the convex surface. Therefore, the author supposes the compact layer is favorable in stabilizing the die surface material from further melting loss, as their formation on the die surface, the melting loss speed will decrease.

  17. Analysis of Intermetallic Phases Formed on Surface Vapor Oxidized H13 Hot Work Steels in Molten Aluminum

    Institute of Scientific and Technical Information of China (English)

    WANG Rong; WU Xiao-chun; MIN Yong-an

    2004-01-01

    In this paper, the author dipped surface vapor oxidized H13 steel specimens into 700℃ molten aluminum liquid for a certain period of time. Analyze the intermetallic phases formed on the H13 samples surface with optical microscope and X-ray diffraction method. The observation of immersion test sample's cross-section shows that Fe3O4 film will protect die substrate from molten aluminum erosion. The identification of the intermetallic phases reveals that they consist of 2parts, which is named as the composite layer and the compact layer. Further investigations are made in order to know the phase constituents of the 2 layers, they are Al8Fe2Si (outer composite layer), (AlCuMg) and Al5Fe2 (compact layer),respectively. The experimental results show that on the same specimen, a convex surface with bigger radius of curvature is more likely to be molten and the melting loss speed is also faster than a flat and smooth surface. The thickness of compact layer on a smooth surface is much bigger than that of the convex surface. Therefore, the author supposes the compact layer is favorable in stabilizing the die surface material from further melting loss, as their formation on the die surface, the melting loss speed will decrease.

  18. Effects of Surface Nitrification on Thermal Conductivity of Modified Aluminum Oxide Nanofibers-Reinforced Epoxy Matrix Nanocomposites

    International Nuclear Information System (INIS)

    Aluminum oxide (Al2O3) nanofibers were treated thermally under an ammonia (NH3) gas stream balanced by nitrogen to form a thin aluminum nitride (AlN) layer on the nanofibers, resulting in the enhancement of thermal conductivity of Al2O3/epoxy nanocomposites. The micro-structural and morphological properties of the NH3-assisted thermally-treated Al2O3 nanofibers were characterized by X-ray diffraction (XRD) and atomic force microscopy (AEM), respectively. The surface characteristics and pore structures were observed by X-ray photoelectron spectroscopy (XPS), Zeta-potential and N2/77 K isothermal adsorptions. From the results, the formation of AlN on Al2O3 nanofibers was confirmed by XRD and XPS. The thermal conductivity (TC) of the modified Al2O3 nanofibers/epoxy composites increased with increasing treated temperatures. On the other hand, the severely treated Al2O3/epoxy composites showed a decrease in TC, resulting from a decrease in the probability of heat-transfer networks between the filler and matrix in this system due to the aggregation of nanofiber fillers

  19. Oxidative removal of acetaminophen using zero valent aluminum-acid system:Efficacy, influencing factors, and reaction mechanism

    Institute of Scientific and Technical Information of China (English)

    Honghua Zhang; Beipei Cao; Wanpeng Liu; Kunde Lin; Jun Feng

    2012-01-01

    Commercial available zero valent aluminum under air-equilibrated acidic conditions (ZVA1/H+/air system) demonstrated an excellent capacity to remove aqueous organic compounds.Acetaminophen (ACTM),the active ingredient of the over-the-counter drug Tylenol(R),is widely present in the aquatic environment and therefore the treatment of ACTM-contaminated water calls for further research.Herein we investigated the oxidative removal of ACTM by ZVAl/H+/air system and the reaction mechanism.In acidic solutions (pH < 3.5),ZVAl displayed an excellent capacity to remove ACTM.More than 99% of ACTM was eliminated within 16 hr in pH 1.5 reaction solutions initially containing 2.0 g/L aluminum and 2.0 mg/L ACTM at 25 ± 1℃.Higher temperature and lower pH facilitated ACTM removal.The addition of different iron species Fe0,Fe2+ and Fe3+ into ZVAl/H+/air system dramatically accelerated the reaction likely due to the enhancing transformation of H2O2 to HO·via Fenton's reaction.Furthermore,the primary intermediate h.ydroquinone and the anions formate,acetate and nitrate,were identified and a possible reaction scheme was proposed.This work suggested that ZVA1/H+/air system may be potentially employed to treat ACTM-contaminated water.

  20. The influence of atmospheric species on the degradation of aluminum doped zinc oxide and Cu(In,Ga)Se2 solar cells

    NARCIS (Netherlands)

    Theelen, M.J.; Foster, C.; Dasgupta, S.; Vroon, Z.A.E.P.; Barreau, N.; Zeman, M.

    2014-01-01

    Aluminum doped zinc oxide (ZnO:Al) layers were exposed to the atmospheric gases carbondioxide (CO2), oxygen (O2), nitrogen (N2) and air as well as liquid H2O purged with these gases, in order to investigate the chemical degradation behavior of these layers. The samples were analyzed by electrical, c

  1. Physical and chemical degradation behavior of sputtered aluminum doped zinc oxide layers for Cu(In,Ga)Se2 solar cells

    NARCIS (Netherlands)

    Theelen, M.; Boumans, T.; Stegeman, F.; Colberts, F.; Illiberi, A.; Berkum, J. van; Barreau, N.; Vroon, Z.; Zeman, M.

    2014-01-01

    Sputtered aluminum doped zinc oxide (ZnO:Al) layers on borosilicate glass were exposed to damp heat (85 C/85% relative humidity) for 2876 h to accelerate the physical and chemical degradation behavior. The ZnO:Al samples were characterized by electrical, compositional and optical measurements before

  2. Fabrication of silver nanoparticles decorated anodic aluminum oxide as the SERS substrate for the detection of pesticide thiram

    Science.gov (United States)

    Tan, En-zhong

    2015-07-01

    An efficient surface-enhanced Raman scattering (SERS) substrate is developed based on silver nanoparticles decorated anodic aluminum oxide (Ag/AAO). The AAO templates were fabricated using a two-step anodization approach, and silver nanoparticles (AgNPs) were obtained by thermal decomposition of Ag nitrate in AAO. The structure of Ag/AAO hybrid substrate is characterized by scanning electron microscopy (SEM). The results show that the as-prepared SERS substrates consist of high-density AgNPs with sizes of tens of nanometers. The AgNPs are adsorbed on the surface of AAO template in the form of network structure which is called "hot spot". The SERS enhancement ability of the nanostructure is verified using thiram as probing molecules. The limit of detection is as low as 1×10-9 mol/L. The results indicate that the as-prepared substrate possesses excellent SERS sensitivity, high stability and uniformity enhancement.

  3. The fabrication of Ag nanoflake arrays via self-assembly on the surface of an anodic aluminum oxide template

    International Nuclear Information System (INIS)

    Vertical-aligned Ag nanoflake arrays are fabricated on the surface of an anodic aluminum oxide (AAO) template under a hydrothermal condition for the first time. The porous surface of AAO templates and the precursor solution may play key roles in the process of fabricating Ag nanoflakes. The rim of pores can provide many active sites for nucleation and growth, and then nanoflake arrays gradually form through self-assembly of Ag on the surface of AAO membranes. The product is characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM), and a growth mechanism of nanoflake is deduced. This work demonstrates that it is possible to make ordered nanoarrays without dissolving templates using the hydrothermal method, and this interesting Ag nanoflake arrays may provide a wider range of nanoscale applications.

  4. Corrosion resistance of flaky aluminum pigment coated with cerium oxides/hydroxides in chloride and acidic electrolytes

    Science.gov (United States)

    Niroumandrad, S.; Rostami, M.; Ramezanzadeh, B.

    2015-12-01

    The objective of this study was to enhance the corrosion resistance of lamellar aluminum pigment through surface treatment by cerium oxides/hydroxides. The surface composition of the pigments was studied by energy-dispersive spectroscopy (EDS) and X-ray photoelectron spectroscopy (XPS). The corrosion resistance of the pigment was evaluated by conventional hydrogen evolution measurements in acidic solution and electrochemical impedance spectroscopy (EIS) in 3.5% NaCl solution. Results showed that the Ce-rich coating composed of Ce2O3 and CeO2 was precipitated on the pigment surface after immersion in the cerium solution. The corrosion resistance of pigment was significantly enhanced after modification with cerium layer.

  5. Porous silicon carbide and aluminum oxide with unidirectional open porosity as model target materials for radioisotope beam production

    International Nuclear Information System (INIS)

    Highlights: • SiC and Al2O3 of uniaxial porosity were produced with ice-templating method. • The method allows controlled pore formation within the material. • Calculation of mechanical integrity under irradiation with protons was performed. • Generated thermal stresses should not exceed material’s strength. -- Abstract: New silicon carbide (SiC) and aluminum oxide (Al2O3) of a tailor-made microstructure were produced using the ice-templating technique, which permits controlled pore formation conditions within the material. These prototypes will serve to verify aging of the new advanced target materials under irradiation with proton beams. Before this, the evaluation of their mechanical integrity was made based on the energy deposition spectra produced by FLUKA codes

  6. Improved light extraction of LYSO scintillator by the photonic structure from a layer of anodized aluminum oxide

    International Nuclear Information System (INIS)

    As a promising scintillator in the field of medical imaging systems, LYSO with its high refractive index suffers from a low light extraction efficiency due to the total internal reflection. Here, we demonstrate that a photonic structure formed by an anodized aluminum oxide layer can enhance the light extraction efficiency by the outcoupling the light trapped in the crystal. An enhancement of light output by 25% can be achieved by an AAO layer covered on the surface of LYSO. The imperfect periodicity of AAO can lead to a consistent enhancement for the entire range of emission wavelength and directionality. Such enhanced light output is practical and attractive for use in the scintillation detection systems. It is important to note that the fabrication method of AAO is simple and low-cost for the large area applications, which is obviously advantageous over the expensive traditional methods such as electron beam lithography

  7. Silver nanoparticles deposited on anodic aluminum oxide template using magnetron sputtering for surface-enhanced Raman scattering substrate

    Energy Technology Data Exchange (ETDEWEB)

    Wong-ek, Krongkamol [Nanoscience and Technology Program, Chulalongkorn University, Bangkok 10330 (Thailand); Eiamchai, Pitak; Horprathum, Mati; Patthanasettakul, Viyapol [National Electronics and Computer Technology Center, 112 Thailand Science Park, Phahonyothin Rd., Klong Luang, Pathumthani 12120 (Thailand); Limnonthakul, Puenisara [Department of Physics, Faculty of Science, King Mongkut' s University of Technology Thonburi, Bangkok 10140 (Thailand); Chindaudom, Pongpan [National Electronics and Computer Technology Center, 112 Thailand Science Park, Phahonyothin Rd., Klong Luang, Pathumthani 12120 (Thailand); Nuntawong, Noppadon, E-mail: noppadon.nuntawong@nectec.or.t [National Electronics and Computer Technology Center, 112 Thailand Science Park, Phahonyothin Rd., Klong Luang, Pathumthani 12120 (Thailand)

    2010-09-30

    Low-cost and highly sensitive surface-enhanced Raman scattering (SERS) substrates have been fabricated by a simple anodizing process and a magnetron sputtering deposition. The substrates, which consist of silver nanoparticles embedded on anodic aluminum oxide (AAO) templates, are investigated by a scanning electron microscope and a confocal Raman spectroscopy. The SERS activities are demonstrated by Raman scattering from adsorbed solutions of methylene blue and pyridine on the SERS substrate surface. The most optimized SERS substrate contains the silver nanoparticles, with a size distribution of 10-30 nm, deposited on the AAO template. From a calculation, the SERS enhancement factor is as high as 8.5 x 10{sup 7}, which suggests strong potentials for direct applications in the chemical detection and analyses.

  8. Simulation study of a highly efficient, high resolution X-ry sensor based on self-organizing aluminum oxide

    CERN Document Server

    Muehlbauer, Joerg; Reims, Nils; Krueger, Peter; Schreiber, Juergen; Mukhurov, Nikolai I; Uhlmann, Norman

    2012-01-01

    State of the art X-ray imaging sensors comprise a trade-off between the achievable efficiency and the spatial resolution. To overcome such limitations, the use of structured and scintillator filled aluminum oxide (AlOx) matrices has been investigated. We used Monte-Carlo (MC) X-ray simulations to determine the X-ray imaging quality of these AlOx matrices. Important factors which influence the behavior of the matrices are: filling factor (surface ratio between channels and 'closed' AlOx), channel diameter, aspect ratio, filling material etc. Therefore we modeled the porous AlOx matrix in several different ways with the MC X-ray simulation tool ROSI [1] and evaluated its properties to investigate the achievable performance at different X-ray spectra, with different filling materials (i.e. scintillators) and varying channel height and pixel readout. In this paper we focus on the quantum efficiency, the spatial resolution and image homogeneity.

  9. The effect of oxygen flow rate on refractive index of aluminum oxide film deposited by electron beam evaporation technique

    Directory of Open Access Journals (Sweden)

    R Shakouri

    2016-02-01

    Full Text Available The effects of oxygen flow rate on refractive index of aluminum oxide film have been investigated. The Al2O3 films are deposited by electron beam on glass substrate at different oxygen flow rates. The substrate was heated to reach  and the temperature was constant during the thin film growth. The transmittance spectrum of samples was recorded in the wavelength 400-800 nm.  Then, using the maxima and minima of transmittance the refractive index and the extinction coefficient of samples were determined. It has been found that if we reduce the oxygen flow, while the evaporation rate is kept constant, the refractive index of Al2O3 films increases. On the other hand, reduced oxygen pressure causes the Al2O3 films to have some absorption.

  10. Compression Molded Ultra High Molecular Weight Polyethylene-Hydroxyapatite-Aluminum Oxide-Carbon Nanotube Hybrid Composites for Hard Tissue Replacement

    Institute of Scientific and Technical Information of China (English)

    Ankur Gupta; Garima Tripathi; Debrupa Lahiri; Kantesh Balani

    2013-01-01

    Ultra high molecular weight polyethylene (UHMWPE) is widely used for articulating surfaces in total hip and knee replacements.In the present work,UHMWPE based polymer composites were synthesized by synergistic reinforcing of bioactive hydroxyapatite (HA),bioinert aluminum oxide (Al2O3),and carbon nanotubes (CNTs) using compression molding.Phase and microstructural analysis suggests retention of UHMWPE and reinforcing phases in the compression molded composites.Microstructural analysis elicited variation in densification due to the size effect of the reinforcing particles.The hybrid composites exhibited hardness,elastic modulus and toughness comparable to that of UHMWPE.The interfacial effect of reinforcement phases has evinced the effectiveness of Al2O3 over HA and CNT reinforcements,depicting synergistic enhancement in hardness and elastic modulus.Weak interfacial bonding of polymer matrix with HA and CNT requires utilization of coupling agents to achieve enhanced mechanical properties without deteriorating cytocompatible properties.

  11. Improved light extraction of LYSO scintillator by the photonic structure from a layer of anodized aluminum oxide

    Science.gov (United States)

    Zhu, Zhichao; Liu, Bo; Cheng, Chuanwei; Zhang, Haifeng; Wu, Shuang; Gu, Mu; Chen, Hong; Chen, Liang; Liu, Jinliang; Ouyang, Xiaoping

    2015-06-01

    As a promising scintillator in the field of medical imaging systems, LYSO with its high refractive index suffers from a low light extraction efficiency due to the total internal reflection. Here, we demonstrate that a photonic structure formed by an anodized aluminum oxide layer can enhance the light extraction efficiency by the outcoupling the light trapped in the crystal. An enhancement of light output by 25% can be achieved by an AAO layer covered on the surface of LYSO. The imperfect periodicity of AAO can lead to a consistent enhancement for the entire range of emission wavelength and directionality. Such enhanced light output is practical and attractive for use in the scintillation detection systems. It is important to note that the fabrication method of AAO is simple and low-cost for the large area applications, which is obviously advantageous over the expensive traditional methods such as electron beam lithography.

  12. Electrodeposited Ni,Fe,Co and Cu single and multilayer nanowire arrays on anodic aluminum oxide template

    Institute of Scientific and Technical Information of China (English)

    Bobomurod HAMRAKULOV; In-Soo KIM; M.G.LEE; B.H.PARK

    2009-01-01

    The Ni, Fe, Co and Cu single and multilayer nanowire arrays to make perpendicular magnetic recording media were fabricated with nanoporous anodic aluminum oxide (AAO) templates from Watt solution and additives by the DC electrodeposition. The results show that the diameters of Ni, Fe, Co and Cu single and multilayer nanowires in AAO templates are 40-80 nm and the lengths are about 30 μm with the aspect ratio of 350-750. The magnetic properties of the prepared nanowires are different under different electrodepositing conditions. The remanences (Br) of Ni/Cu/Fe multilayer nanowires are lower than those of others multilayer nanowires, and coercivity (Hc) of Ni/Cu/Fe multilayer nanowires are lower than those of others multilayer nanowires. These are compatible with the required conditions of high density magnetic media devices that should have the low coercivity to easily success magnetization and high remanence to keep magnetization after removal of magnetic field.

  13. Effects of acetic acid on microstructure and electrochemical properties of nano cerium oxide films coated on AA7020-T6 aluminum alloy

    Institute of Scientific and Technical Information of China (English)

    H. Hasannejad; T. Shahrabi; M. Aliofkhazraei

    2009-01-01

    Nano cerium oxide films were applied on AA7020-T6 aluminum alloy and the effects of acetic acid concentration on the microstructure and electrochemical properties of the coated samples were investigated by using scanning electron microscopy (SEM), X-ray diffraction (XRD), crack-flee films with well-developed grains were obtained and grain sizes of the films decreased. Elimination of cracks and decreasing grain size of the nano cerium oxide films caused corrosion resistance to increase.

  14. Enhanced adsorptive removal of p-nitrophenol from water by aluminum metal–organic framework/reduced graphene oxide composite

    Science.gov (United States)

    Wu, Zhibin; Yuan, Xingzhong; Zhong, Hua; Wang, Hou; Zeng, Guangming; Chen, Xiaohong; Wang, Hui; Zhang, Lei; Shao, Jianguang

    2016-05-01

    In this study, the composite of aluminum metal–organic framework MIL-68(Al) and reduced graphene oxide (MA/RG) was synthesized via a one–step solvothermal method, and their performances for p–nitrophenol (PNP) adsorption from aqueous solution were systematically investigated. The introduction of reduced graphene oxide (RG) into MIL-68(Al) (MA) significantly changes the morphologies of the MA and increases the surface area. The MA/RG-15% prepared at RG-to-MA mass ratio of 15% shows a PNP uptake rate 64% and 123% higher than MIL-68(Al) and reduced graphene oxide (RG), respectively. The hydrogen bond and π – π dispersion were considered to be the major driving force for the spontaneous and endothermic adsorption process for PNP removal. The adsorption kinetics, which was controlled by film–diffusion and intra–particle diffusion, was greatly influenced by solution pH, ionic strength, temperature and initial PNP concentration. The adsorption kinetics and isotherms can be well delineated using pseudo–second–order and Langmuir equations, respectively. The presence of phenol or isomeric nitrophenols in the solution had minimal influence on PNP adsorption by reusable MA/RG composite.

  15. Enhanced adsorptive removal of p-nitrophenol from water by aluminum metal–organic framework/reduced graphene oxide composite

    Science.gov (United States)

    Wu, Zhibin; Yuan, Xingzhong; Zhong, Hua; Wang, Hou; Zeng, Guangming; Chen, Xiaohong; Wang, Hui; zhang, Lei; Shao, Jianguang

    2016-01-01

    In this study, the composite of aluminum metal–organic framework MIL-68(Al) and reduced graphene oxide (MA/RG) was synthesized via a one–step solvothermal method, and their performances for p–nitrophenol (PNP) adsorption from aqueous solution were systematically investigated. The introduction of reduced graphene oxide (RG) into MIL-68(Al) (MA) significantly changes the morphologies of the MA and increases the surface area. The MA/RG-15% prepared at RG-to-MA mass ratio of 15% shows a PNP uptake rate 64% and 123% higher than MIL-68(Al) and reduced graphene oxide (RG), respectively. The hydrogen bond and π – π dispersion were considered to be the major driving force for the spontaneous and endothermic adsorption process for PNP removal. The adsorption kinetics, which was controlled by film–diffusion and intra–particle diffusion, was greatly influenced by solution pH, ionic strength, temperature and initial PNP concentration. The adsorption kinetics and isotherms can be well delineated using pseudo–second–order and Langmuir equations, respectively. The presence of phenol or isomeric nitrophenols in the solution had minimal influence on PNP adsorption by reusable MA/RG composite. PMID:27181188

  16. Enhanced adsorptive removal of p-nitrophenol from water by aluminum metal-organic framework/reduced graphene oxide composite.

    Science.gov (United States)

    Wu, Zhibin; Yuan, Xingzhong; Zhong, Hua; Wang, Hou; Zeng, Guangming; Chen, Xiaohong; Wang, Hui; Zhang, Lei; Shao, Jianguang

    2016-01-01

    In this study, the composite of aluminum metal-organic framework MIL-68(Al) and reduced graphene oxide (MA/RG) was synthesized via a one-step solvothermal method, and their performances for p-nitrophenol (PNP) adsorption from aqueous solution were systematically investigated. The introduction of reduced graphene oxide (RG) into MIL-68(Al) (MA) significantly changes the morphologies of the MA and increases the surface area. The MA/RG-15% prepared at RG-to-MA mass ratio of 15% shows a PNP uptake rate 64% and 123% higher than MIL-68(Al) and reduced graphene oxide (RG), respectively. The hydrogen bond and π - π dispersion were considered to be the major driving force for the spontaneous and endothermic adsorption process for PNP removal. The adsorption kinetics, which was controlled by film-diffusion and intra-particle diffusion, was greatly influenced by solution pH, ionic strength, temperature and initial PNP concentration. The adsorption kinetics and isotherms can be well delineated using pseudo-second-order and Langmuir equations, respectively. The presence of phenol or isomeric nitrophenols in the solution had minimal influence on PNP adsorption by reusable MA/RG composite. PMID:27181188

  17. Comparative Assessment of Antimicrobial Efficiency of Ionic Silver, Silver Monoxide, and Metallic Silver Incorporated onto an Aluminum Oxide Nanopowder Carrier

    International Nuclear Information System (INIS)

    The present paper provides comparative assessment of antimicrobial efficiency of ionic silver (Ag+), silver monoxide (Ag2O), and metallic silver (Ag) incorporated onto an aluminum oxide nanopowder carrier (Al2O3). The deposition of Ag+ ions, Ag2O nanoparticles, and Ag nanoparticles on an different phases of aluminum oxide nanopowder carrier was realized using consecutive stages of dry sol-gel method. The Al2O3-Ag+, Al2O3-Ag2O, and Al2O3-Ag nanopowders were widely characterized qualitatively and quantitatively by SEM, physical nitrogen sorption and XRD analyses. Results indicate that the Al2O3 nanopowders added with Ag+, Ag2O, and Ag, apart from phase composition, were not differing considerably from one another in terms of their morphology and physical properties. However, nanopowders of Al2O3-Ag were more agglomerated than Al2O3-Ag2O and Al2O3-Ag+ nanopowders. The antibacterial activity of the nanopowders was examined by the spread plate method using bacterial strains such as Escherichia coli, Sarcina lutea, and Bacillus subtilis. The best antibacterial properties against Sarcina lutea strain were achieved in the amorphous-Al2O3-Ag+ and Al2O3-Ag2O nanopowders, whereas the worst antimicrobial activity against Bacillus subtilis and Escherichia coli was shown by the Al2O3-Ag+ and Al2O3-Ag nanopowders. The observed increase of the antibacterial activity as the silver content was not however significant for Al2O3-Ag nanopowders. The results obtained in the present experiments show that the Al2O3-Ag+, Al2O3-Ag2O, and Al2O3-Ag nanopowders, possessing good bactericidal properties, can be produced by using consecutive stages of dry sol-gel method, and Al2O3 nanopowder added with Ag2O is considered as the best raw material in the production of antiseptic materials.

  18. Electrochemical potentials of layered oxide and olivine phosphate with aluminum substitution: A first principles study

    Indian Academy of Sciences (India)

    Arun Kumar Varanasi; Phani Kanth Sanagavarapu; Arghya Bhowmik; Mridula Dixit Bharadwaj; Balasubramanian Narayana; Umesh V Waghmare; Dipti Deodhare; Alind Sharma

    2013-12-01

    First-principles prediction of enhancement in the electrochemical potential of LiCoO2 with aluminum substitution has been realized through earlier experiments. For safer and less expensive Li-ion batteries, it is desirable to have a similar enhancement for alternative cathode materials, LiFePO4 and LiCoPO4. Here, we present first-principles density functional theory based analysis of the effects of aluminum substitution on electrochemical potential of LiCoO2, LiFePO4 and LiCoPO4. While Al substitution for transition metal results in increase in electrochemical potential of LiCoO2, it leads to reduction in LiFePO4 and LiCoPO4. Through comparative topological analysis of charge density of these materials, we identify a ratio of Bader charges that correlates with electrochemical potential and determine the chemical origin of these contrasting effects: while electronic charge from lithium is transferred largely to oxygen in LiCoO2, it gets shared by the oxygen and Co/Fe in olivine phosphates due to strong covalency between O and Co/Fe. Our work shows that covalency of transition metal–oxygen bond plays a key role in determining battery potential.

  19. EFFECT OF ANION, PH, AND TEMPERATURE ON THE DISSOLUTION BEHAVIOR OF ALUMINUM OXIDE FILMS

    International Nuclear Information System (INIS)

    The growth and dissolution behavior of oxide film on abraded pure Al has been investigated using cyclic polarization and has been found to be highly dependent on solution chemistry and temperature. The nature of the anions, borate, chromate, phosphate, and sulfate, at pH 3 to 11, and temperatures 0 to 60 C were examined. In near neutral solutions the dissolution behavior was greatly affected by each anion. In borate and chromate solutions at near neutral pH and room temperature, the currents continued to decrease with each subsequent cycle due to oxide thickening. In contrast, a significant rate of oxide dissolution occurred to produce reproducible repetitive curves during subsequent cycles in a phosphate and sulfate. Sulfate also produced a distinctly different mode during high field oxide growth. In increasing acidic (pH and lt; 4) or basic (pH and gt;9) solutions the oxide dissolution rate increased rapidly. The oxide dissolution rate was always enhanced with increasing temperature. At high pH (and gt;9) or elevated temperature (60 C), a current maximum was observed in chromate, due to a diffusion controlled monochromate ion enhanced dissolution reaction at the oxide/solution interface

  20. EFFECT OF ANION, PH, AND TEMPERATURE ON THE DISSOLUTION BEHAVIOR OF ALUMINUM OXIDE FILMS.

    Energy Technology Data Exchange (ETDEWEB)

    LEE,H.; ISAACS,H.S.

    2001-09-02

    The growth and dissolution behavior of oxide film on abraded pure Al has been investigated using cyclic polarization and has been found to be highly dependent on solution chemistry and temperature. The nature of the anions, borate, chromate, phosphate, and sulfate, at pH 3 to 11, and temperatures 0 to 60 C were examined. In near neutral solutions the dissolution behavior was greatly affected by each anion. In borate and chromate solutions at near neutral pH and room temperature, the currents continued to decrease with each subsequent cycle due to oxide thickening. In contrast, a significant rate of oxide dissolution occurred to produce reproducible repetitive curves during subsequent cycles in a phosphate and sulfate. Sulfate also produced a distinctly different mode during high field oxide growth. In increasing acidic (pH < 4) or basic (pH >9) solutions the oxide dissolution rate increased rapidly. The oxide dissolution rate was always enhanced with increasing temperature. At high pH (>9) or elevated temperature (60 C), a current maximum was observed in chromate, due to a diffusion controlled monochromate ion enhanced dissolution reaction at the oxide/solution interface.

  1. Thermal oxidation of single crystal aluminum antimonide and materials having the same

    Science.gov (United States)

    Sherohman, John William; Yee, Jick Hong; Coombs, III, Arthur William; Wu, Kuang Jen J.

    2012-12-25

    In one embodiment, a method for forming a non-conductive crystalline oxide layer on an AlSb crystal includes heat treating an AlSb crystal in a partial vacuum atmosphere at a temperature conducive for air adsorbed molecules to desorb, surface molecule groups to decompose, and elemental Sb to evaporate from a surface of the AlSb crystal and exposing the AlSb crystal to an atmosphere comprising oxygen to form a crystalline oxide layer on the surface of the AlSb crystal. In another embodiment, a method for forming a non-conductive crystalline oxide layer on an AlSb crystal includes heat treating an AlSb crystal in a non-oxidizing atmosphere at a temperature conducive for decomposition of an amorphous oxidized surface layer and evaporation of elemental Sb from the AlSb crystal surface and forming stable oxides of Al and Sb from residual surface oxygen to form a crystalline oxide layer on the surface of the AlSb crystal.

  2. Oxidation of hydrogen-passivated silicon surfaces by scanning near-field optical lithography using uncoated and aluminum-coated fiber probes

    DEFF Research Database (Denmark)

    Madsen, Steen; Bozhevolnyi, Sergey I.; Birkelund, Karen;

    1997-01-01

    Optically induced oxidation of hydrogen-passivated silicon surfaces using a scanning near-field optical microscope was achieved with both uncoated and aluminum-coated fiber probes. Line scans on amorphous silicon using uncoated fiber probes display a three-peak profile after etching in potassium...... hydroxide. Numerical simulations of the electromagnetic field around the probe-sample interaction region are used to explain the experimental observations. With an aluminum-coated fiber probe, lines of 35 nm in width were transferred into the amorphous silicon layer. (C) 1997 American Institute of Physics....

  3. A corrosion resistant cerium oxide based coating on aluminum alloy 2024 prepared by brush plating

    International Nuclear Information System (INIS)

    Cerium oxide based coatings were prepared on AA2024 Al alloy by brush plating. The characteristic of this technology is that hydrogen peroxide, which usually causes the plating solution to be unstable, is not necessary in the plating electrolyte. The coating showed laminated structures and good adhesive strength with the substrate. X-ray diffraction and X-ray photoelectron spectroscopy analysis showed that the coatings were composed of Ce(III) and Ce(IV) oxides. The brush plated coatings on Al alloys improved corrosion resistance. The influence of plating parameters on structure and corrosion resistance of the cerium oxide based coating was studied.

  4. A corrosion resistant cerium oxide based coating on aluminum alloy 2024 prepared by brush plating

    Energy Technology Data Exchange (ETDEWEB)

    Tang Junlei; Han Zhongzhi [School of Materials Science and Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); Zuo Yu, E-mail: zuoy@mail.buct.edu.cn [School of Materials Science and Engineering, Beijing University of Chemical Technology, Beijing 100029 (China); Tang Yuming [School of Materials Science and Engineering, Beijing University of Chemical Technology, Beijing 100029 (China)

    2011-01-15

    Cerium oxide based coatings were prepared on AA2024 Al alloy by brush plating. The characteristic of this technology is that hydrogen peroxide, which usually causes the plating solution to be unstable, is not necessary in the plating electrolyte. The coating showed laminated structures and good adhesive strength with the substrate. X-ray diffraction and X-ray photoelectron spectroscopy analysis showed that the coatings were composed of Ce(III) and Ce(IV) oxides. The brush plated coatings on Al alloys improved corrosion resistance. The influence of plating parameters on structure and corrosion resistance of the cerium oxide based coating was studied.

  5. Stability and corrosion resistance of superhydrophobic surface on oxidized aluminum in NaCl aqueous solution

    Science.gov (United States)

    Lv, Damei; Ou, Junfei; Xue, Mingshan; Wang, Fajun

    2015-04-01

    Superhydrophobic surface (SHS) was fabricated on aluminum via surface roughening by NaClO and surface passivation by hexadecyltrimethoxysilane. The long-term durability for storing the sample in air and the chemical stability for contacting the sample with NaCl solution were investigated. The short-term corrosion resistance for immersing the sample in NaCl solution for 1 h was investigated by potentiodynamic polarization, and the long-term corrosion resistance for immersing the sample in NaCl solution for 7 days was investigated by variation analyses on surface wettability, surface morphology, and surface chemistry. All experimental results suggested that the so-obtained SHS possessed good stability and good corrosion resistance under the testing conditions.

  6. Partial oxidation of dimethyl ether using the structured catalyst Rh/Al2O3/Al prepared through the anodic oxidation of aluminum.

    Science.gov (United States)

    Yu, B Y; Lee, K H; Kim, K; Byun, D J; Ha, H P; Byun, J Y

    2011-07-01

    The partial oxidation of dimethyl ether (DME) was investigated using the structured catalyst Rh/Al2O3/Al. The porous Al2O3 layer was synthesized on the aluminum plate through anodic oxidation in an oxalic-acid solution. It was observed that about 20 nm nanopores were well developed in the Al2O3 layer. The thickness of Al2O3 layer can be adjusted by controlling the anodizing time and current density. After pore-widening and hot-water treatment, the Al2O3/Al plate was calcined at 500 degrees C for 3 h. The obtained delta-Al2O3 had a specific surface area of 160 m2/g, making it fit to be used as a catalyst support. A microchannel reactor was designed and fabricated to evaluate the catalytic activity of Rh/Al2O3/Al in the partial oxidation of DME. The structured catalyst showed an 86% maximum hydrogen yield at 450 degrees C. On the other hand, the maximum syngas yield by a pack-bed-type catalyst could be attained by using a more than fivefold Rh amount compared to that used in the structured Rh/Al2O3/Al catalyst. PMID:22121705

  7. Aluminum oxide thin films deposited on silicon substrates from Al(NO{sub 3}){sub 3} and an organic solvent by spray pyrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Aguilar-Frutis, M.; Alejos, T. [Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada del IPN, Legaria 694 Col. Irrigacion, Del. Miguel Hidalgo C.P. 11500, Mexico DF (Mexico); Guzman-Mendoza, J. [Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada del IPN, Legaria 694 Col. Irrigacion, Del. Miguel Hidalgo C.P. 11500, Mexico DF (Mexico); Instituto de Investigaciones en Materiales, Universidad Nacional Autonoma de Mexico, Del. Coyoacan C.P. 04510, Mexico DF (Mexico); Garcia-Hipolito, M. [Instituto de Investigaciones en Materiales, Universidad Nacional Autonoma de Mexico, Del. Coyoacan C.P. 04510, Mexico DF (Mexico); Falcony, C. [Centro de Investigacion y de Estudios Avanzados del IPN, Apdo. Postal 14-740, 07000, Mexico DF (Mexico)

    2003-09-01

    Aluminum oxide thin films were deposited on silicon substrates at temperatures in the range from 500 to 650 C, from Al(NO{sub 3}){sub 3} dissolved in N,N-Dimethylformamide and using the spray pyrolysis technique. The films of aluminum oxide resulted stoichiometric, amorphous and optically transparent in the visible spectrum, with a refractive index close to 1.66 when a 0.2 molar solution of Al(NO{sub 3}){sub 3} was used. The films as deposited had a surface roughness as low as 3.8 nm and were almost free of Al-OH bonds, depending on the experimental deposition conditions. The best films were incorporated in a Metal-Oxide-Semiconductor structure and were able to stand electric fields up to 2 MV/cm without destructive breakdown and a dielectric constant of 7.95. (copyright 2003 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  8. Influence of copper in spheres of iron and aluminum oxide; Influencia do cobre nas propriedades texturais e estruturais de esferas de oxido de ferro e aluminio

    Energy Technology Data Exchange (ETDEWEB)

    Sousa, A.F. de; Gomes, E.C.C.; Valentini, A.; Longhinotti, E., E-mail: adfrsou@hotmail.co [Universidade Federal do Ceara (UFC), Fortaleza, CE (Brazil). Dept. de Quimica Analitica e Fisico-Quimica; Sales, F.A.M. [Universidade Federal do Ceara (UFC), Fortaleza, CE (Brazil). Dept. de Fisica

    2010-07-01

    The various applications of mesoporous materials in adsorption and catalysis have driven research for new synthetic routes to improve the structural and morphological characteristics of the compounds currently available. Spherical mesoporous materials of aluminum oxide and / or iron were synthesized in proportions of 10.30 and 50%, and then impregnated with copper oxide by wet impregnation method. Supporters of spherical iron oxide and aluminum before and after impregnation with copper were characterized by XRD, SEM, chemical analysis, BET and TPR. The analysis results of XRD showed the formation of crystalline phases AB{sub 2}O{sub 4} type, the results of TPR showed a shift of the band of iron reduction with the incorporation of copper and the samples indicated a decrease in porosity, possibly due to the closure of pores with the addition of copper. (author)

  9. Characterization and wear- and corrosion-resistance of microarc oxidation ceramic coatings on aluminum alloy

    Energy Technology Data Exchange (ETDEWEB)

    Wei Tongbo [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Yan Fengyuan [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China)]. E-mail: fyyan@ns.lzb.ac.cn; Tian Jun [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China)

    2005-03-08

    Thick and hard ceramic coatings were prepared on Al-Cu-Mg alloy (2024 Al alloy) making use of microarc oxidation in an alkali-silicate electrolytic solution. The microstructure, phase composition, corrosion resistance friction and wear behaviors of the microarc oxidation coatings and the impact toughness of the impacted Al alloy blocks were investigated. Moreover, the corroded surfaces and the impacted surfaces and cross-sections of the microarc oxidation coatings were observed with a scanning electron microscope. The results show that the microarc oxidation coatings can be divided into a porous loose outer region consisting predominantly of {gamma}-Al{sub 2}O{sub 3} and Al-Si-O phase and a dense internal region consisting predominantly of {alpha}-Al{sub 2}O{sub 3}. They have excellent corrosion resistance, though the thicker coating shows somewhat poorer corrosion-resistance than the thinner one. The differences in the corrosion-resistance of the microarc oxidation coatings with different thicknesses are related to their different microstructures. The impact toughness of the Al alloy substrate is decreased after modification with the microarc oxidation coatings of extremely high hardness. This implies that the microarc oxidation coatings on the Al alloy substrate may not be suitable to impacting working condition. After abrasion away of the loose outer layer, the polished compact inner coatings possess excellent wear- and corrosion-resistance and strong adhesion to the substrate, and they show further significantly improved wear-resistance under the lubrication of a commercial 4838 lubricating oil. Namely, the friction coefficient and wear rate of the polished 100 {mu}m coating under the oil-lubricated-condition are reduced to be 1/10 and 1/1000 of that under dry sliding. The microarc oxidation coatings mainly composed of hard {alpha}-Al{sub 2}O{sub 3} could find promising application in preventing the corrosion and wear of Al alloy-based components.

  10. Evolution of micro-arc oxidation behaviors of the hot-dipping aluminum coatings on Q235 steel substrate

    International Nuclear Information System (INIS)

    Micro-arc oxidation (MAO) is not applicable to prepare ceramic coatings on the surface of steel directly. In this work, hybrid method of MAO and hot-dipping aluminum (HDA) were employed to fabricate composite ceramic coatings on the surface of Q235 steel. The evolution of MAO coatings, such as growth rate, thickness of the total coatings, ingrown and outgrown coatings, cross section and surface morphologies and phase composition of the ceramic coatings were studied. The results indicate that both the current density and the processing time can affect the total thickness, the growth rate and the ratio of ingrown and outgrown thickness of the ceramic coatings. The total thickness, outgrown thickness and growth rate have maximum values with the processing time prolonged. The time when the maximum value appears decreases and the ingrown dominant turns to outgrown dominant little by little with the current density increasing. The composite coatings obtained by this hybrid method consists of three layers from inside to outside, i.e. Fe-Al alloy layer next to the substrate, aluminum layer between the Fe-Al layer and the ceramic coatings which is as the top exterior layer. Metallurgical bonding was observed between every of the two layers. There are many micro-pores and micro-cracks, which act as discharge channels and result of quick and non-uniform cooling of melted sections in the MAO coatings. The phase composition of the ceramic coatings is mainly composed of amorphous phase and crystal Al2O3 oxides. The crystal Al2O3 phase includes κ-Al2O3, θ-Al2O3 and β-Al2O3. Compared with the others, the β-Al2O3 content is the least. The MAO process can be divided into three periods, namely the common anodic oxidation stage, the stable MAO stage and the ceramic coatings destroyed stage. The exterior loose part of the ceramic coatings was destroyed badly in the last period which should be avoided during the MAO process.

  11. Synergistic Effect of Superhydrophobicity and Oxidized Layers on Corrosion Resistance of Aluminum Alloy Surface Textured by Nanosecond Laser Treatment.

    Science.gov (United States)

    Boinovich, Ludmila B; Emelyanenko, Alexandre M; Modestov, Alexander D; Domantovsky, Alexandr G; Emelyanenko, Kirill A

    2015-09-01

    We report a new efficient method for fabricating a superhydrophobic oxidized surface of aluminum alloys with enhanced resistance to pitting corrosion in sodium chloride solutions. The developed coatings are considered very prospective materials for the automotive industry, shipbuilding, aviation, construction, and medicine. The method is based on nanosecond laser treatment of the surface followed by chemisorption of a hydrophobic agent to achieve the superhydrophobic state of the alloy surface. We have shown that the surface texturing used to fabricate multimodal roughness of the surface may be simultaneously used for modifying the physicochemical properties of the thick surface layer of the substrate itself. Electrochemical and wetting experiments demonstrated that the superhydrophobic state of the metal surface inhibits corrosion processes in chloride solutions for a few days. However, during long-term contact of a superhydrophobic coating with a solution, the wetted area of the coating is subjected to corrosion processes due to the formation of defects. In contrast, the combination of an oxide layer with good barrier properties and the superhydrophobic state of the coating provides remarkable corrosion resistance. The mechanisms for enhancing corrosion protective properties are discussed. PMID:26271017

  12. Analysis on porous aluminum anodic oxide film formed in Re-OA-H3PO4 solution

    International Nuclear Information System (INIS)

    An anodic porous film on aluminum was prepared in a mixed electrolyte of phosphoric acid and organic acid and cerium salt. The growth, morphology and chemical composition of the film were investigated. The results indicate that the growth of porous layers in this solution undergo three stages during anodizing, as in other conventional solution, while the whole growth rate is nonlinear. This electrolyte is sensitive to anodizing temperature, which affects current density in great degree. SEM indicates the surface morphology of film is strongly dependent on temperature and current density and its cross-section has two distinct oxide layers. Al, O and P are found in the film with different distribution in the two layers with EPMA. However, Ce has been detected on the outer surface with EDAX. XPS analysis on the electron binding energy of the component elements show the chemical composition of oxide film surface are Al2O3, Ce(OH) and some phosphates. The formation mechanics of Ce compound is also deduced

  13. Graphene Oxide/Polyacrylamide/Aluminum Ion Cross-Linked Carboxymethyl Hemicellulose Nanocomposite Hydrogels with Very Tough and Elastic Properties.

    Science.gov (United States)

    Kong, Weiqing; Huang, Danyang; Xu, Guibin; Ren, Junli; Liu, Chuanfu; Zhao, Lihong; Sun, Runcang

    2016-06-01

    Development of high-strength hydrogels has recently attracted ever-increasing attention. In this work, a new design strategy has been proposed to prepare graphene oxide (GO)/polyacrylamide (PAM)/aluminum ion (Al(3+) )-cross-linked carboxymethyl hemicellulose (Al-CMH) nanocomposite hydrogels with very tough and elastic properties. GO/PAM/Al-CMH hydrogels were synthesized by introducing graphene oxide (GO) into PAM/CMH hydrogel, followed by ionic cross-linking of Al(3+) . The nanocomposite hydrogels were characterized by means of FTIR, X-ray diffraction (XRD), and scanning electron microscopy/energy-dispersive X-ray analysis (SEM-EDX) along with their swelling and mechanical properties. The maximum compressive strength and the Young's modulus of GO3.5 /PAM/Al-CMH0.45 hydrogel achieved values of up to 1.12 and 13.27 MPa, increased by approximately 6488 and 18330 % relative to the PAM hydrogel (0.017 and 0.072 MPa). The as-prepared GO/PAM/Al-CMH nanocomposite hydrogels possess high strength and great elasticity giving them potential in bioengineering and drug-delivery system applications. PMID:27062081

  14. Evaluation of cerium oxide coated Cu cermets as inert anodes for aluminum electrowinning. Final report, August 1990--March 1992

    Energy Technology Data Exchange (ETDEWEB)

    1992-08-01

    Cu/NiFe{sub 2}O{sub 4} cermets were evaluated, with and without an in-situ deposited CEROX (TM; cerium oxide) coating, in 100 h laboratory A1 electrowinning tests. Bath ratio and current density were varied between tests and corrosion was determined by contamination of the aluminum and cryolite by cermet components (Cu, Fe, and Ni). Higher bath ratios of 1.5 to 1.6 led to less corrosion and thicker CEROX coatings. Lower current densities led to slightly less corrosion but much less oxidation of the Cu cermet substrate. At identical test conditions, the corrosion of the CEROX coated cermets was 1/7 that of an uncoated cermet. Corrosion was increased in CEROX coated cermets tested under unsaturated alumina conditions. The electrical conductivity of the CEROX coating was measured to be {approximately}0.2 ohm{sup {minus}1}cm{sup {minus}1}, resulting in a slight voltage penalty, depending on the thickness of the coating.

  15. Selection of crucible oxides in molten titanium and titanium aluminum alloys by thermo-chemistry calculations

    OpenAIRE

    Kostov A.; Friedrich B

    2005-01-01

    Titanium and its alloys interstitially dissolve a large amount of impurities such as oxygen and nitrogen, which degrade the mechanical and physical properties of alloys. On the other hand crucible oxides based on CaO, ZrO2 Y2O3, etc., and their spinels (combination of two or more oxides) can be used for melting titanium and its alloys. However, the thermodynamic behavior of calcium, zirconium, yttrium on the one side, and oxygen on the other side, in molten Ti and Ti-Al alloys have not been m...

  16. Effect of aluminum addition on electrical properties, dielectric characteristics, and its stability of (Pr, Co, Cr, Y)-added zinc oxide-based varistors

    Indian Academy of Sciences (India)

    Choon-W Nahm

    2010-06-01

    The electrical properties, dielectric characteristics, and its stability against d.c. accelerated aging stress of (Pr, Co, Cr, Y)-added zinc oxide-based varistors were investigated for different aluminum concentrations under a sintering temperature of 1280°C. As the aluminum concentration increased, the average grain size () increased in the range of 4.3–5.5 m and the sintered density increased in the range of 5.63–5.67 g/cm3. As the aluminum concentration increased, the breakdown field decreased in the range of 6327–710 V/cm and the maximum nonlinear coefficient (46.9) was obtained for 0.005 mol% in aluminum concentration, further additions impaired the nonlinear properties. As the aluminum concentration increased, the apparent dielectric constant increased in the range of 500.5–1327.4 and dissipation factor increased in the range of 0.00493–0.0724. The varistor added with 0.001 mol% Al exhibited the highest stability for – characteristics in which % 1\\ mA is +1.4% and % is –5.7%, under stress state of 0.95 1\\ mA/150° C/24 h.

  17. The Effect of Microarc Oxidation (MAO Modes on Corrosion Behavior of High-Silicon Aluminum Alloy

    Directory of Open Access Journals (Sweden)

    S.К. Kiselyeva

    2014-07-01

    Full Text Available The investigation studies the properties of hardened surface layers, developed with the microarc oxidation method (MAO on ingots of a Al-Si alloy. It has been proved that properties of the developed surfaces (microhardness, thickness, porosity and corrosion properties depend on the concentration of electrolyte components.

  18. Fractionation of fulvic acid by iron and aluminum oxides: influence on copper toxicity to Ceriodaphnia dubia

    Science.gov (United States)

    Smith, Kathleen S.; James F. Ranville; Emily K. Lesher; Daniel J. Diedrich; Diane M. McKnight; Ruth M. Sofield

    2014-01-01

    This study examines the effect on aquatic copper toxicity of the chemical fractionation of fulvic acid (FA) that results from its association with iron and aluminum oxyhydroxide precipitates. Fractionated and unfractionated FAs obtained from streamwater and suspended sediment were utilized in acute Cu toxicity tests on ,i>Ceriodaphnia dubia. Toxicity test results with equal FA concentrations (6 mg FA/L) show that the fractionated dissolved FA was 3 times less effective at reducing Cu toxicity (EC50 13 ± 0.6 μg Cu/L) than were the unfractionated dissolved FAs (EC50 39 ± 0.4 and 41 ± 1.2 μg Cu/L). The fractionation is a consequence of preferential sorption of molecules having strong metal-binding (more aromatic) moieties to precipitating Fe- and Al-rich oxyhydroxides, causing the remaining dissolved FA to be depleted in these functional groups. As a result, there is more bioavailable dissolved Cu in the water and hence greater potential for Cu toxicity to aquatic organisms. In predicting Cu toxicity, biotic ligand models (BLMs) take into account dissolved organic carbon (DOC) concentration; however, unless DOC characteristics are accounted for, model predictions can underestimate acute Cu toxicity for water containing fractionated dissolved FA. This may have implications for water-quality criteria in systems containing Fe- and Al-rich sediment, and in mined and mineralized areas in particular. Optical measurements, such as specific ultraviolet absorbance at 254 nm (SUVA254), show promise for use as spectral indicators of DOC chemical fractionation and inferred increased Cu toxicity.

  19. The effect of Bi{sup 3+} and Li{sup +} co-doping on the luminescence characteristics of Eu{sup 3+}-doped aluminum oxide films

    Energy Technology Data Exchange (ETDEWEB)

    Padilla-Rosales, I., E-mail: ipadilla@cinvestav.mx [Centro de Investigación y de Estudios Avanzados del IPN, Nanociencias y Nanotecnología, Av. IPN 2508, Col. San Pedro Zacatenco, CP 07360 México D.F. (Mexico); Martinez-Martinez, R. [Instituto de Física y Matemáticas, Universidad Tecnológica de la Mixteca, Carretera a Acatlima Km. 2.5, CP 69000 Huajuapan de León, Oax, México (Mexico); Cabañas, G. [Centro de Investigación y de Estudios Avanzados del IPN, Nanociencias y Nanotecnología, Av. IPN 2508, Col. San Pedro Zacatenco, CP 07360 México D.F. (Mexico); Falcony, C. [Centro de Investigación y de Estudios Avanzados del IPN, Departamento de Física, Av. IPN 2508, Col. San Pedro Zacatenco, CP 07360 México D.F. (Mexico)

    2015-09-15

    The incorporation of Bi{sup 3+} and Li{sup +} as co-dopants in Eu{sup 3+}-doped aluminum oxide films deposited by the ultrasonic spray pyrolysis technique and its effect on the luminescence characteristics of this material are described. Both Bi{sup 3+} and Li{sup +} do not introduce new luminescence features but affect the luminescence intensity of the Eu{sup 3+} related emission spectra as well as the excitation spectra. The introduction of Bi{sup 3+} generates localized states in the aluminum oxide host that result in a quenching of the luminescence intensity, while Li{sup +} and Bi{sup 3+} co-doping increase the luminescence intensity of these films. - Highlights: • Li and Bi co-doping increase the luminescence. • Bi creates localized states in the Al{sub 2}O{sub 3} host. • Li was incorporated as a co-activator.

  20. Fabrication of a Zinc Aluminum Oxide Nanowire Array Photoelectrode for a Solar Cell Using a High Vacuum Die Casting Technique

    OpenAIRE

    Chin-Guo Kuo; Jung-Hsuan Chen; Yueh-Han Liu

    2014-01-01

    Zinc aluminum alloy nanowire was fabricated by the vacuum die casting. Zinc aluminum alloy was melted, injected into nanomold under a hydraulic pressure, and solidified as nanowire shape. Nanomold was prepared by etching aluminum sheet with a purity of 99.7 wt.% in oxalic acid solution. A nanochannel within nanomold had a pore diameter of 80 nm and a thickness of 40 μm. Microstructure and characteristic analysis of the alumina nanomold and zinc-aluminum nanowire were performed by scanning ele...

  1. DEGRADATION OF SM2ZR2O7 THERMAL BARRIER COATING CAUSED BY CALCIUM-MAGNESIUM-ALUMINUM-SILICON OXIDE (CMAS) DEPOSITION

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Honglong; Sheng, Zhizhi; Tarwater, Emily; Zhang, Xingxing; Dasgupta, Sudip; Fergus, Jeffrey

    2015-03-16

    Rare earth zirconates are promising materials for use as thermal barrier coatings in gas turbine engines. Among the lanthanide zirconate materials, Sm2Zr2O7 with the pyrochlore structure has lower thermal conductivity and better corrosion resistance against calcium-magnesium-aluminum-silicon oxide (CMAS). In this work, after reaction with CMAS, the pyrochlore structure transforms to the cubic fluorite structure and Ca2Sm8(SiO4)6O2 forms in elongated grain.

  2. On the kinetics of the aluminum-water reaction during exposure in high-heat flux test loops: 1, A computer program for oxidation calculations

    International Nuclear Information System (INIS)

    The ''Griess Correlation,'' in which the thickness of the corrosion product on aluminum alloy surfaces is expressed as a function of time and temperature for high-flux-reactor conditions, was rewritten in the form of a simple, general rate equation. Based on this equation, a computer program that calculates oxide-layer thickness for any given time-temperature transient was written. 4 refs

  3. Ultra-violet Sensing Characteristic and Field Emission Properties of Vertically Aligned Aluminum Doped Zinc Oxide Nanorod Arrays

    International Nuclear Information System (INIS)

    Ultra-violet (UV) sensing behavior and field emission characteristic have been investigated on vertically aligned aluminum (Al) doped zinc oxide (ZnO) nanorod arrays prepared using sol-gel immersion method. Uniform and high coverage density of ZnO nanorod arrays have been successfully deposited on seeded-catalyst coated substrates. The synthesized nanorods have diameter sizes between 50 nm to 150 nm. The XRD spectra show Al doped ZnO nanorod array has high crystallinity properties with the dominancy of crystal growth along (002) plane or c-axis. UV photoresponse measurement indicates that Al doped ZnO nanorod array sensitively detects UV light as shown by conductance increment after UV illumination exposure. The nanorod array shows good field emission properties with low turn on field and threshold field at 2.1 V/μm and 5.6 V/μm, respectively. The result suggested that Al doped ZnO nanorod arrays prepared by low-cost sol-gel immersion method show promising result towards fabrication of multi applications especially in UV photoconductive sensor and field emission displays.

  4. Integrative functional transcriptomic analyses implicate specific molecular pathways in pulmonary toxicity from exposure to aluminum oxide nanoparticles.

    Science.gov (United States)

    Li, Xiaobo; Zhang, Chengcheng; Bian, Qian; Gao, Na; Zhang, Xin; Meng, Qingtao; Wu, Shenshen; Wang, Shizhi; Xia, Yankai; Chen, Rui

    2016-09-01

    Gene expression profiling has developed rapidly in recent years and it can predict and define mechanisms underlying chemical toxicity. Here, RNA microarray and computational technology were used to show that aluminum oxide nanoparticles (Al2O3 NPs) were capable of triggering up-regulation of genes related to the cell cycle and cell death in a human A549 lung adenocarcinoma cell line. Gene expression levels were validated in Al2O3 NPs exposed A549 cells and mice lung tissues, most of which showed consistent trends in regulation. Gene-transcription factor network analysis coupled with cell- and animal-based assays demonstrated that the genes encoding PTPN6, RTN4, BAX and IER play a role in the biological responses induced by the nanoparticle exposure, which caused cell death and cell cycle arrest in the G2/S phase. Further, down-regulated PTPN6 expression demonstrated a core role in the network, thus expression level of PTPN6 was rescued by plasmid transfection, which showed ameliorative effects of A549 cells against cell death and cell cycle arrest. These results demonstrate the feasibility of using gene expression profiling to predict cellular responses induced by nanomaterials, which could be used to develop a comprehensive knowledge of nanotoxicity. PMID:26830206

  5. Fabrication of Pd Micro-Membrane Supported on Nano-Porous Anodized Aluminum Oxide for Hydrogen Separation.

    Science.gov (United States)

    Kim, Taegyu

    2015-08-01

    In the present study, nano-porous anodized aluminum oxide (AAO) was used as a support of the Pd membrane. The AAO fabrication process consists of an electrochemical polishing, first/second anodizing, barrier layer dissolving and pores widening. The Pd membrane was deposited on the AAO support using an electroless plating with ethylenediaminetetraacetic acid (EDTA) as a plating agent. The AAO had the regular pore structure with the maximum pore diameter of ~100 nm so it had a large opening area but a small free standing area. The 2 µm-thick Pd layer was obtained by the electroless plating for 3 hours. The Pd layer thickness increased with increasing the plating time. However, the thickness was limited to ~5 µm in maximum. The H2 permeation flux was 0.454 mol/m2-s when the pressure difference of 66.36 kPa0.5 was applied at the Pd membrane under 400 °C. PMID:26369167

  6. Effect of annealing on the magnetic properties of Ni nanowires prepared by using an anodized aluminum oxide template

    International Nuclear Information System (INIS)

    We report the growth mechanism and the magnetic properties of Ni nanowires on an anodized aluminum oxide (AAO) template. The porous AAO was fabricated using a two-step anodization process. The Ni nanowires were grown by using DC pulsed and AC electrodeposition methods, and the Ni nanowires were more uniformly grown by using the AC electrodeposition method than by using the DC pulsed electrodeposition method. We also studied the magnetic properties of the Ni nanowires and the post-annealed Ni nanowires (at 600 .deg. C in air). The annealed Ni nanowires showed smaller ferromagnetic saturation than the unannealed Ni nanowires. This result indicates that NiO existed in the Ni nanowires after the post-annealing process. In addition, the magnetic properties of the Ni nanowires at 5 K showed that the easy magnetization axis in the annealed Ni nanowires had rotated from the parallel to the nanowire surface to the perpendicular to that surface. Since the shape anisotropy of continuous Ni thin films favors the direction of the easy magnetization axis being parallel to direction of their surfaces, these results show that at low temperatures, the magnetic properties of Ni nanowires behave as those of continuous Ni thin films.

  7. Impedance spectroscopy of highly ordered nano-porous electrodes based on Au-AAO (anodic aluminum oxide) structure.

    Science.gov (United States)

    Ahn, Jaehwan; Cho, Sungbo; Min, Junhong

    2013-11-01

    Electrochemical measurements using the microelectrodes are increasingly utilized for the label-free detection of the small amount of biological materials such as DNA, protein, and cells. However, the interfacial electrode impedance increases and may hinder the detection of weak signals as the size of electrode decreases. To enhance the measurement sensitivity while reducing the electrode size, in this study, microelectrodes employing a nanoporous structure were fabricated and characterized by using electrical impedance spectroscopy. We made the highly ordered honeycomb nanoporous structure of Anodic Aluminum Oxide (AAO) by electrochemical anodizing and formed Au layer on the surface of AAO (Au/AAO) by electroless Au plating method. The electrical characteristics of the fabricated Au/AAO electrodes were evaluated by using de Levie's model derived for the pore electrodes. As a result, the interfacial electrode impedance of the fabricated Au/AAO electrodes was 2-3 order lower than the value of the planar electrodes at frequencies below 1 kHz. It implies this nanoporous electrode could be directly applied to label free detection of biomaterials. PMID:24245278

  8. Electrophoretic deposition of multi-walled carbon nanotubes on porous anodic aluminum oxide using ionic liquid as a dispersing agent

    Science.gov (United States)

    Hekmat, F.; Sohrabi, B.; Rahmanifar, M. S.; Jalali, A.

    2015-06-01

    Multi-wall carbon nanotubes (MW-CNTs) have been arranged in nanochannels of anodic aluminum oxide template (AAO) by electrophoretic deposition (EPD) to make a vertically-aligned carbon nanotube (VA-CNT) based electrode. Well ordered AAO templates were prepared by a two-step anodizing process by applying a constant voltage of 45 V in oxalic acid solution. The stabilized CNTs in a water-soluble room temperature ionic liquid (1-methyl-3-octadecylimidazolium bromide), were deposited in the pores of AAO templates which were conductive by deposition of Ni nanoparticles in the bottom of pores. In order to obtain ideal results, different EPD parameters, such as concentration of MWCNTs and ionic liquid on stability of MWCNT suspensions, deposition time and voltage which are applied in EPD process and also optimal conditions for anodizing of template were investigated. The capacitive performance of prepared electrodes was analyzed by measuring the specific capacitance from cyclic voltammograms and the charge-discharge curves. A maximum value of 50 Fg-1 at the scan rate of 20 mV s-1was achieved for the specific capacitance.

  9. Facile fabrication of Ag dendrite-integrated anodic aluminum oxide membrane as effective three-dimensional SERS substrate

    Science.gov (United States)

    Zhang, Cong-yun; Lu, Ya; Zhao, Bin; Hao, Yao-wu; Liu, Ya-qing

    2016-07-01

    A novel surface enhanced Raman scattering (SERS)-active substrate has been successfully developed, where Ag-dendrites are assembled on the surface and embedded in the channels of anodic aluminum oxide (AAO) membrane, via electrodeposition in AgNO3/PVP aqueous system. Reaction conditions were systematically investigated to attain the best Raman enhancement. The growth mechanism of Ag dendritic nanostructures has been proposed. The Ag dendrite-integrated AAO membrane with unique hierarchical structures exhibits high SERS activity for detecting rhodamine 6G with a detection limit as low as 1 × 10-11 M. Furthermore, the three-dimensional (3D) substrates display a good reproducibility with the average intensity variations at the major Raman peak less than 12%. Most importantly, the 3D SERS substrates without any surface modification show an outstanding SERS response for the molecules with weak affinity for noble metal surfaces. The potential application for the detection of polycyclic aromatic hydrocarbons (PAHs) was evaluated with fluoranthene as Raman target molecule and a sensitive SERS detection with a limit down to 10-8 M was reached. The 3D SERS-active substrate shows promising potential for rapid detection of trace organic pollutants even weak affinity molecules in the environment.

  10. Preparation and characterization of solid-state sintered aluminum-doped zinc oxide with different alumina contents

    Indian Academy of Sciences (India)

    Yu-Hsien Chou; J L H Chau; W L Wang; C S Chen; S H Wang; C C Yang

    2011-06-01

    Aluminum-doped zinc oxide (AZO) ceramics with 0−2.5 wt.% alumina (Al2O3) content were prepared using a solid-state reaction technique. It was found that AZO grains became finer in size and more irregular in shape than undoped ZnO as the Al2O3 content increased. Addition of Al2O3 dopant caused the formation of phase transformation stacking faults in ZnO grains. The second phase, ZnAl2O4 spinel, was observed at the grain boundaries and triple junctions, and inside the grains. In this study, a 3-inch circular Al2O3 (2 wt.%)-doped ZnO ceramic target sintered at 1500°C for 6 h has a relative density of 99.8% with a resistivity of 1.8 × 10-3 -cm. The AZO film exhibits optical transparency of 90.3% in the visible region and shows an electrical resistivity of 2.5 × 10-3 -cm.

  11. Nanoporous anodic aluminum oxide as a promising material for the electrostatically-controlled thin film interference filter

    International Nuclear Information System (INIS)

    This study presents the approach to implement the electrostatically-controlled thin film optical filter by using a nanoporous anodic aluminum oxide (np-AAO) layer as the key suspended micro structure. The bi-stable optical filter operates in the visible spectral range. In this work, the presented bi-stable optical filter has averaged reflectivity of 60%, and the central wavelengths are 580 and 690 nm respectively for on and off states. The presented np-AAO layer offers the following merits for the thin film optical filter: (1) material properties of np-AAO film, such as refractive index, elastic modulus and dielectric constant, can be easily changed by a low temperature pore-widening process, (2) in-use stiction of the suspended np-AAO structure can be reduced by the small contact area of nanoporous textures, (3) driving (pull-in) voltage can be reduced due to a large dielectric constant (εAAO is 7.05) and small stiffness of np-AAO film and (4) dielectric charging can be reduced by the np-AAO material; thus the offset voltage is small. The study reports the design, fabrication and experimental results of the bi-stable optical filter to demonstrate the advantages of the presented device. The np-AAO material also has the potential for applications of other electrostatic drive micro devices. (paper)

  12. Effect of carbon nanotube and aluminum oxide addition on plasma-sprayed hydroxyapatite coating's mechanical properties and biocompatibility

    International Nuclear Information System (INIS)

    This study reports on the synthesis of novel bioceramic composite coating of hydroxyapatite (HA) reinforced with carbon nanotubes (CNTs) and aluminum oxide (Al2O3) using plasma spray technique. Fracture toughness of HA-20 wt.% Al2O3 improved by 158% as compared to HA coating whereas HA-18.4 wt.% Al2O3-1.6 wt.% CNT showed an improvement of 300%. Carbon nanotubes provided reinforcement via rebar mechanism. Human fiber osteoblast cell-growth studies showed that biocompatibility of the coating remained unaltered, as Al2O3 retained its bio-inertness and CNT, its bioactivity, within the composite coatings. Composite coating showed lower attachment, but higher proliferation rate, for the osteoblast cells, which has been attributed to the surface roughness. An optimized relation between coating composition, its biocompatibility and mechanical properties was established to predict the most suited coating material for orthopedic implants. HA-Al2O3-CNT composite coating displayed most improved mechanical properties while retaining its biocompatibility.

  13. Novel approach for synthesis of boehmite nanostructures and their conversion to aluminum oxide nanostructures for remove Congo red.

    Science.gov (United States)

    Liu, Xueming; Niu, Chunge; Zhen, Xinping; Wang, Jide; Su, Xintai

    2015-08-15

    A phase transfer method was developed to prepare boehmite (γ-AlOOH) nanostructures with various morphologies including nanofragments, nanorods, nanoflakes and multiply stacked nanostructures. The effect of the reaction temperature on the morphology of the as-prepared γ-AlOOH was investigated systematically. After calcination, the corresponding aluminum oxide (γ-Al2O3) nanostructures were obtained from the as-prepared γ-AlOOH products and preserving the same morphology. The obtained samples were characterized by several techniques, such as X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM) and N2 adsorption-desorption technique. The possible formation mechanism of the boehmites has also been proposed. Adsorption experiments indicated that γ-Al2O3 nanorods exhibited better adsorption capacity for Congo red (CR) in contrast to other as-prepared γ-Al2O3 nanostructures and commercial alumina (Al2O3), and the adsorption obeyed well to Langmuir isotherm model. Besides, the adsorption kinetics followed pseudo-second-order rate equation. PMID:25935282

  14. Oxidation study on as-bonded intermetallic of copper wire–aluminum bond pad metallization for electronic microchip

    International Nuclear Information System (INIS)

    In this work, influence of Copper free air ball (FAB) oxidation towards Intermetallic Compound (IMC) at Copper wire–Aluminum bond pad metallization (Cu/Al) is studied. Samples are synthesized with different Copper FAB oxidation condition by turning Forming Gas supply ON and OFF. Studies are performed using Optical Microscope (OM), Scanning Electron Microscope (SEM), Transmission Electron Microscope (TEM) and line-scan Energy Dispersive X-ray (EDX). SEM result shows there is a cross-sectional position offset from center in sample synthesized with Forming Gas OFF. This is due to difficulty of determining the position of cross-section in manual grinding/polishing process and high occurrence rate of golf-clubbed shape of oxidized Copper ball bond. TEM inspection reveals that the Copper ball bond on sample synthesized with Forming Gas OFF is having intermediate oxidation. Besides, the presence of IMC at the bonding interface of Cu/Al for both samples is seen. TEM study shows voids form at the bonding interface of Forming Gas ON sample belongs to unbonded area; while that in Forming Gas OFF sample is due to volume shrinkage of IMC growth. Line-scan EDX shows the phases present in the interfaces of as-bonded samples are Al4Cu9 (∼3 nm) for sample with Forming Gas ON and mixed CuAl and CuAl2 (∼15 nm) for sample with Forming Gas OFF. Thicker IMC in sample with Forming Gas OFF is due to cross-section is positioned at high stress area that is close to edge of ball bond. Mechanical ball shear test shows that shear strength of sample with Forming Gas OFF is about 19% lower than that of sample with Forming Gas ON. Interface temperature is estimated at 437 °C for as-bonded sample with Forming Gas ON by using empirical parabolic law of volume diffusion. -- Highlights: ► 3 nm Al4Cu9 are found in sample prepared with Forming Gas ON. ► 15 nm mixed CuAl + CuAl2 are found in sample prepared with Forming Gas OFF. ► Voids are present at the bonding interfaces of both samples

  15. Oxidation study on as-bonded intermetallic of copper wire-aluminum bond pad metallization for electronic microchip

    Energy Technology Data Exchange (ETDEWEB)

    Joseph Sahaya Anand, T., E-mail: anand@utem.edu.my [Faculty of Manufacturing Engineering, University Technical Malaysia Melaka, Hang Tuah Jaya, 76100 Durian Tunggal, Melaka (Malaysia); Yau, Chua Kok [Faculty of Manufacturing Engineering, University Technical Malaysia Melaka, Hang Tuah Jaya, 76100 Durian Tunggal, Melaka (Malaysia); University of Technical Malaysia Supported by Infineon Technology - Malaysia - Sdn. Bhd., Melaka (Malaysia); Huat, Lim Boon [Department of Innovation, Infineon Technology - Malaysia - Sdn. Bhd., FTZ Batu Berendam, 75350 Melaka (Malaysia)

    2012-10-15

    In this work, influence of Copper free air ball (FAB) oxidation towards Intermetallic Compound (IMC) at Copper wire-Aluminum bond pad metallization (Cu/Al) is studied. Samples are synthesized with different Copper FAB oxidation condition by turning Forming Gas supply ON and OFF. Studies are performed using Optical Microscope (OM), Scanning Electron Microscope (SEM), Transmission Electron Microscope (TEM) and line-scan Energy Dispersive X-ray (EDX). SEM result shows there is a cross-sectional position offset from center in sample synthesized with Forming Gas OFF. This is due to difficulty of determining the position of cross-section in manual grinding/polishing process and high occurrence rate of golf-clubbed shape of oxidized Copper ball bond. TEM inspection reveals that the Copper ball bond on sample synthesized with Forming Gas OFF is having intermediate oxidation. Besides, the presence of IMC at the bonding interface of Cu/Al for both samples is seen. TEM study shows voids form at the bonding interface of Forming Gas ON sample belongs to unbonded area; while that in Forming Gas OFF sample is due to volume shrinkage of IMC growth. Line-scan EDX shows the phases present in the interfaces of as-bonded samples are Al{sub 4}Cu{sub 9} ({approx}3 nm) for sample with Forming Gas ON and mixed CuAl and CuAl{sub 2} ({approx}15 nm) for sample with Forming Gas OFF. Thicker IMC in sample with Forming Gas OFF is due to cross-section is positioned at high stress area that is close to edge of ball bond. Mechanical ball shear test shows that shear strength of sample with Forming Gas OFF is about 19% lower than that of sample with Forming Gas ON. Interface temperature is estimated at 437 Degree-Sign C for as-bonded sample with Forming Gas ON by using empirical parabolic law of volume diffusion. -- Highlights: Black-Right-Pointing-Pointer 3 nm Al{sub 4}Cu{sub 9} are found in sample prepared with Forming Gas ON. Black-Right-Pointing-Pointer 15 nm mixed CuAl + CuAl{sub 2} are found

  16. Influence of sodium silicate concentration on structural and tribological properties of microarc oxidation coatings on 2017A aluminum alloy substrate

    Energy Technology Data Exchange (ETDEWEB)

    Polat, Aytekin, E-mail: apolat@nigde.edu.t [Department of Mechanical Engineering, Nigde University, Nigde 51100 (Turkey); Makaraci, Murat [Department of Mechanical Engineering, Kocaeli University, Kocaeli (Turkey); Usta, Metin [Department of Materials Science and Engineering, Gebze Institute of Technology, Kocaeli (Turkey)

    2010-08-20

    In this paper, thick and hard oxide coatings resistant to wear were produced on 2017A-T6 Al alloy by the microarc oxidation (MAO) technique in an alkali electrolyte consisting of different sodium silicate concentrations (0-8 g/l). The coatings were characterized by means of optical microscopy, scanning electron microscopy (SEM), X-ray diffraction (XRD) and surface profilometry. Microhardness, scratch adhesion and pin-on-disk sliding wear tests were also performed to evaluate the tribological properties of the coatings. The influence of sodium silicate concentration on the structural and tribological properties of the MAO coatings was discussed. Results reveal that increasing sodium silicate concentration from 0 to 8 g/l in the electrolyte caused an increase in the electrolyte conductivity (from 7.71 to 18.1 mS/cm) and a decrease in positive final voltage (from 627 to 590 V) in the MAO process. In response to the increase in sodium silicate concentration, the thickness, surface roughness (R{sub a}) and critical load (L{sub c}) corresponding to adhesive failure of the coatings were increased simultaneously from 74 to 144 {mu}m, and 4.4 to 6.58 {mu}m, and 127.76 to 198.54 N, respectively. At the same time, the phase structure and composition of the coatings also varied by the participation of silicate ions in the reactions and their incorporation into the coating structure. Moreover, it was observed that the coating formed in the low sodium silicate concentration (4 g/l) had higher surface hardness (2020 HV) and improved wear resistance than the one (1800 HV) formed in the high sodium silicate concentration (8 g/l). The coatings produced in three different electrolytic solutions provided an excellent wear resistance and a load carrying capacity compared to the uncoated aluminum alloy.

  17. STRUCTURAL PROPERTIES ALUMINUM OXIDE FILMS AS A FUNCTION OF DEPOSITION ANGLE

    International Nuclear Information System (INIS)

    Full text: Aluminium Oxide films were deposited on glass substrates (18? 18 ? 1 mm,cut from microscope slide) by using resistive evaporation method, from tungsten boats, at room temperature, of two different depositions 20 and 50 degree deposition angles. The evaporated material was pieces of Aluminium Oxide. An ETS 160 (Vacuum Evaporation System) coating plant with a base pressure of 3 ? 10?5 mbar, was used. Prior to deposition, all glass substrates were ultrasonically cleaned in heated acetone first and then in ethanol. The substrate holder was a disk of 36.5 cm in diameter with adjustable height up to 50 cm and also adjustable holders for placing any kind of substrates. Thickness of layers was determined by quartz crystal microbalance technique. The other deposition conditions such as deposition rate, vacuum pressure, and substrate temperature were the same in all tests.The surface physical morphology and roughness were obtained by means of AFM(Dual Scope TM DS 95-200/50) analysis. Scanning electron microscopy methodused for determining nanostructure of layers. The transmittance of films was measured using UV-VIS spectrophotometer (Hitachi U ? 3310) instrument. The spectra of layers were in range of 300?1100 nm wavelength (UV-VIS). The transmission (?T) of electrons through thin films of C, Al2O3, Al, Ni, Ag, and Au, together with their distribution in angle and energy, can measured in a spherical retarding-potential analyzer.Aluminium Oxide thin films of 65 nm thickness at two different deposition angles of 20 and 50 degrees were deposited on glass substrates at room temperature, by using resistive evaporation method under UHV conditions. The structural details were determined by AFM and SEM methods. The optical spectra were measured by spectrophotometer in the spectral range of 300 ?1100 nm wave length (UV-VIS).The relation between nanostructures and optical properties to deposition angle were discussed.

  18. Oxidation and corrosion behavior of titanium aluminum nitride coatings by arc ion plating

    Institute of Scientific and Technical Information of China (English)

    LI Ming-sheng; FENG Chang-jie; ZHANG Zhi-feng; WANG Fu-hui

    2006-01-01

    Composite metastable TiN and Ti1-xAlxN coatings with different Al content were deposited on 1Cr11Ni2W2MoV stainless steel for aero-engine compressor blades by arc ion plating. The results show that all coatings have a B1NaCl structure and the preferred orientation changes from (111) to (220) with increasing Al content; the lattice parameter of Ti1-xAlxN decreases with the increase of Al content. The oxidation-resistance of (Ti,Al)N coatings is significantly improved owing to the formation of Al-riched oxide on the surface of the coatings. The nitride coatings can significantly improve the corrosion-resistance of 1Cr11Ni2W2MoV stainless steel under the synergistic of water vapor and NaCl, and the corrosion-resistance becomes better when the Al content increases, because not only the quick formation of thin alumina layer prevents the further corrosion but also the formation of alumina seals the pinholes or defects in the coatings, which prevents the occurrence of localized nodules-like corrosion.

  19. The study of the volume expansion of aluminum during porous oxide formation at galvanostatic regime

    International Nuclear Information System (INIS)

    The volume expansion factor of porous alumina, formed by through anodizing of an Al foil of thickness 11.5 μm in the range of current densities of 4-35 mA cm-2 in oxalic and sulfuric acid at 18-24 deg. C has been studied. The microstructure of anodizing samples has been observed using scanning electron microscopy. The thickness of obtained porous alumina films was measured by a mechanical profilometer with a computer signal-processing. The volume expansion factor of porous alumina varied from 1.35 to 1.65. Linear dependences were obtained for the volume expansion factor of porous alumina versus the anodizing voltage and the ionic current-density logarithm versus the inverse volume expansion factor. Unlike oxide formation in sulfuric acid, these dependences have two subsequential rectilinear regions in oxalic acid. This peculiarity of the dependences in oxalic acid was explained by formation of a region of the immobile negative space charge in the barrier Al oxide layer and its influence on the ionic transport

  20. Evolution of the thickness of the aluminum oxide film due to the pH of the cooling water and surface temperature of the fuel elements clad of a nuclear reactor

    International Nuclear Information System (INIS)

    This paper describes the mechanism of growth of a film of aluminum oxide on an alloy of the same material, which serves as a protective surface being the constituent material of the RP-10 nuclear reactor fuel elements clads. The most influential parameters on the growth of this film are: the pH of the cooling water and the clad surface temperature of the fuel element. For this study, a mathematical model relating the evolution of the aluminum oxide layer thickness over the time, according to the same oxide film using a power law is used. It is concluded that the time of irradiation, the heat flux at the surface of the aluminum material, the speed of the coolant, the thermal conductivity of the oxide, the initial thickness of the oxide layer and the solubility of the protective oxide are parameters affecting in the rate and film formation. (author).

  1. High temperature oxidation behavior of gamma-nickel+gamma'-nickel aluminum alloys and coatings modified with platinum and reactive elements

    Science.gov (United States)

    Mu, Nan

    Materials for high-pressure turbine blades must be able to operate in the high-temperature gases (above 1000°C) emerging from the combustion chamber. Accordingly, the development of nickel-based superalloys has been constantly motivated by the need to have improved engine efficiency, reliability and service lifetime under the harsh conditions imposed by the turbine environment. However, the melting point of nickel (1455°C) provides a natural ceiling for the temperature capability of nickel-based superalloys. Thus, surface-engineered turbine components with modified diffusion coatings and overlay coatings are used. Theses coatings are capable of forming a compact and adherent oxide scale, which greatly impedes the further transport of reactants between the high-temperature gases and the underlying metal and thus reducing attack by the atmosphere. Typically, these coatings contain beta-NiAl as a principal constituent phase in order to have sufficient aluminum content to form an Al2O3 scale at elevated temperatures. The drawbacks to the currently-used beta-based coatings, such as phase instabilities, associated stresses induced by such phase instabilities, and extensive coating/substrate interdiffusion, are major motivations in this study to seek next-generation coatings. The high-temperature oxidation resistance of novel Pt+Hf-modified gamma-Ni+gamma'-Ni 3Al-based alloys and coatings were investigated in this study. Both early-stage and 4-days isothermal oxidation behavior of single-phase gamma-Ni and gamma'-Ni3Al alloys were assessed by examining the weight changes, oxide-scale structures, and elemental concentration profiles through the scales and subsurface alloy regions. It was found that Pt promotes Al 2O3 formation by suppressing the NiO growth on both gamma-Ni and gamma'-Ni3Al single-phase alloys. This effect increases with increasing Pt content. Moreover, Pt exhibits this effect even at lower temperatures (˜970°C) in the very early stage of oxidation. It

  2. Fabrication of aluminum foam from aluminum scrap Hamza

    Directory of Open Access Journals (Sweden)

    O. A. Osman1 ,

    2015-02-01

    Full Text Available In this study the optimum parameters affecting the preparation of aluminum foam from recycled aluminum were studied, these parameters are: temperature, CaCO3 to aluminum scrap wt. ratio as foaming agent, Al2O3 to aluminum scrap wt. ratio as thickening agent, and stirring time. The results show that, the optimum parameters are the temperature ranged from 800 to 850oC, CaCO3 to aluminum scrap wt. ratio was 5%, Al2O3 to aluminum scrap wt. ratio was 3% and stirring time was 45 second with stirring speed 1200 rpm. The produced foam apparent densities ranged from 0.40-0.60 g/cm3. The microstructure of aluminum foam was examined by using SEM, EDX and XRD, the results show that, the aluminum pores were uniformly distributed along the all matrices and the cell walls covered by thin oxide film.

  3. Kinetic of sintering of polyethilene glycol and lanthanum dopped aluminum oxide obtained by the sol-gel method

    Directory of Open Access Journals (Sweden)

    Novaković Tatjana B.

    2011-01-01

    Full Text Available Sintering and crystallization of low-density polyethylene glycol (PEG and lanthanum, La(III-doped Al2O3 aerogels prepared from aluminum isopropoxide were investigated. The sintering behavior of non-doped and doped aerogels was examined by following the change of specific surface area with isothermal heat-treatment. The specific surface area and crystalline phases of non-doped and PEG+La(III-doped aerogels were determined, and the effects of dopants on the sintering and crystallization of Al2O3 aerogels are discussed. Isothermal sintering experiments showed that the sintering mechanism of non-doped and PEG+La(III-doped Al2O3 aerogels is surface diffusion. The specific surface areas of alumina samples decrease rapidly during the initial period of sintering, and more slowly with prolonged sintering time. The change of the porous structure is correlated with the phase transformation of γ-Al2O3 during calcinations of Al2O3 aerogels. The surface area of non-doped Al2O3 aerogels came to about 20 m2g-1 with heat-treatment at 1100°C because of crystallization of α-Al2O3 after densification. In the case of heattreatment at 1200°C, the largest surface area was observed for PEG+La(III doped Al2O3 aerogels and the XRD pattern showed only low ordered θ-Al2O3. These indicate that the addition of PEG+La(III to boehmite sol prevents Al2O3 aerogels from sintering and crystallizing to the α-Al2O3 phase. Even after 20 h at 1000°C, PEG+La (III-doped alumina samples maintain a rather good specific surface area (108 m2 g-1 in comparison to the non-doped, containing mainly θ-Al2O3 and minor amounts of δ-Al2O3. Aluminum-oxides with these structural and textural properties are widely used as a coatings and catalyst supports in the field of various catalysis.

  4. Characterizing Pyroxene Reaction Space in Calcium-Aluminum Rich Inclusions: Oxidation During CAI Rim Formation

    Science.gov (United States)

    Dyl, K. A.; Young, E. D.

    2009-12-01

    We define the reaction space that controls changes in pyroxene composition in CAIs and Wark-Lovering (WL) rims in an oxidizing solar nebula. Ti-rich pyroxenes in CAIs record a sub-solar oxygen fugacity (Ti3+/Ti4+~1.5). WL rim pyroxenes in the CAI Leoville 144A have a distinctly lower oxidation state.This difference supports WL rim condensation in an environment of increasing O2(g) and Mg(g) (Simon et al. 2005). We used the following phase components to identify four linearly independent reactions (Thompson 1982): diopside, CaTs (Al2Mg-1Si-1), T3 (Ti3+AlMg-1Si-1), T4 (Ti4+Al2Mg-1Si-2), En (MgCa-1), perovskite, O(g), Mg(g), SiO(g), and Ca(g). Compositional variation in this system is dominated by two reactions. The first is oxidation of Ti3+ via reaction with O and Mg in the gas phase: 1.5 O(g) + Mg(g) → ¼ Di + [Ti4+Mg3/4Ti3+-1Ca-1/4Si-1/2] (1). Pyroxene is produced and En is introduced. The second reaction (2) is perovskite formation. It is observed in the WL rim of Leoville 144A, and experiments confirm that an elevated Ti component converts pyroxene to perovskite(Gupta et al. 1973). MgCa-1 is the third linearly independent reaction (3). They combine to give: ½ Di + x Ca(g)→ x Mg(g)+ Pv + [Mg1/2-xSiTi4+-1Ca-1/2+x](2,3). Unlike (1), pyroxene is consumed in this reaction. The parameter x defines the extent of Mg-Ca exchange. When x > 0.5, WL rim formation occurs in an environment where Mg is volatile and Ca condenses. The reaction space defined by reactions (1) and (2,3) describes the transition from CAI interior to WL rims. WL rim pyroxene Ti contents, [CaTs], and Ca < 1 pfu are all explained in this space. The fourth linearly independent reaction is SiO(g):1/8 Di + ¼ Mg(g)→ ¾ SiO(g) + [Mg3/8Ca1/8Ti4+Ti3+-1Si-1/2](4). Silica reduction forms Ti4+, releasing SiO(g). (4) does not describe the oxidation of Ti3+ in WL rim pyroxene, but (1) - (4) results in En formation directly from the gas phase. This may explain WL rim analyses that have Si contents in excess

  5. Crystal orientation dependent thermoelectric properties of highly oriented aluminum-doped zinc oxide thin films

    KAUST Repository

    Abutaha, Anas I.

    2013-02-06

    We demonstrate that the thermoelectric properties of highly oriented Al-doped zinc oxide (AZO) thin films can be improved by controlling their crystal orientation. The crystal orientation of the AZO films was changed by changing the temperature of the laser deposition process on LaAlO3 (100) substrates. The change in surface termination of the LaAlO3 substrate with temperature induces a change in AZO film orientation. The anisotropic nature of electrical conductivity and Seebeck coefficient of the AZO films showed a favored thermoelectric performance in c-axis oriented films. These films gave the highest power factor of 0.26 W m−1 K−1 at 740 K.

  6. Adsorption of titanium, chromium, and copper atoms on thin aluminum and magnesium oxide film surfaces

    Science.gov (United States)

    Tvauri, I. V.; Turiev, A. M.; Tsidaeva, N. I.; Gazzaeva, M. E.; Vladimirov, G. G.; Magkoev, T. T.

    2012-04-01

    Methods of Auger electron spectroscopy (AES), spectroscopy of characteristic electron energy losses (SCEEL), slow electron diffraction (SED), and contact potential difference (CPD) in ultrahigh vacuum are used to investigate the adsorption-emission properties and stability of two-component film systems formed by putting of Ti, Cr, and Cu atoms on MgO-Mo(011) and Al2O3-Mo(011) surfaces. All atoms have the properties of electronegative adsorbates. Continuous adatom monolayers are formed on the Al2O3-Mo(011) system surface, and three-dimensional islands are formed on the MgO-Mo(011) surface. The properties of monoatomic films on the oxide layer surface are close to those observed for bulk materials. No radical changes of the system properties are detected with increasing dielectric layer thickness. The thermal stability of the newly formed structures decreases in the order Ti, Cr, Cu, Al2O3(MgO), and Mo(011).

  7. Water electrolysis-induced optical degradation of aluminum-doped zinc oxide films

    International Nuclear Information System (INIS)

    A type of optical degradation of aluminium-doped zinc oxide (AZO) films due to water electrolysis-induced reduction reaction was reported. An experiment was designed in which AZO films were immersed in a 0.01 M NaOH aqueous solution as cathode to electrolyze water. Significant decreases in the optical transmission of the treated samples were observed. Studies by X-ray diffraction and scanning electron microscope showed that the degradation of AZO films was due to compositional and structural changes with the treatment of water electrolysis, which resulted from the reduction reaction of atomic hydrogen generated in the electrolysis of water. This optical degradation reflects the stability degradation of AZO films under water electrolysis environment

  8. Pull-test adhesion measurements of diamondlike carbon films on silicon carbide, silicon nitride, aluminum oxide, and zirconium oxide

    International Nuclear Information System (INIS)

    Hydrogenated amorphous carbon or diamondlike carbon (DLC) films were formed by 400 eV methane (CH4) ion bombardment of various smooth and rough ceramics, as well as ceramics coated with a layer of Si or Ti. Adhesion was measured by a bonded-pin method. Excellent adhesion was measured for smooth SiC and Si3N4, but adhesion of DLC to smooth Al2O3 and ZrO2 was negligible. The use of a Si bonding interlayer produced good adhesion to all the substrates, but a Ti layer was ineffective due to poor bonding between the DLC film and Ti. Bulk thermodynamic calculations are not directly applicable to bonding at the interface because the interface is two dimensional and the compositions of interfacial phases are generally not known. If the standard enthalpy ΔH degree for the reaction between CH4 and the substrate material is calculated under the assumption that a carbide phase is produced, a relationship is seen between the reaction enthalpy and the relative adhesion. Large positive enthalpies are associated with poor adhesion; negative or small positive enthalpies are associated with good adhesion. This relation between enthalpy and adhesion was also observed for DLC deposited on Si. The lack of adhesion to the Ti was attributed to inadvertent formation of a surface oxide layer that rendered the enthalpy for the reaction with CH4 positive

  9. Effects of Surface Oxide on the Nitridation Behavior of Aluminum Particles

    Science.gov (United States)

    Kim, Sung-Hoon; Noh, Jae-Hong; Ahn, Jae-Pyoung; Lee, Jae-Chul; Kwon, Hoon; Lee, Jaegab; Yang, Heang Ryeal; Lee, Kon-Bae

    2015-01-01

    A detailed transmission electron microscopy study coupled with electron energy loss spectroscopy was conducted on AlN formed by the direct nitridation of Al particles under nitrogen atmosphere. The nitridation mechanism comprised two steps: the formation of AlN shell on Al particles and the growth of AlN with a lath type in Al droplets. Here, we found that the surface oxide layer of the Al particles acted as a channel layer, which supplied nitrogen in the atomic state to liquid Al, after being transformed into a thin AlON layer during the initial nitridation. In the Al particles, the inward growth of AlN with a shell structure occurred at the sub layer of the AlON layer. On the other hand, the extracted liquid Al droplets formed after the cracking of the AlN shell rested on the Al particles surrounded by the AlON layer. The nitridation of the droplets began at the interface between the Al particle and droplet and not at the free surface and grew outward from the droplet. Herein, based on the observation of the AlON layer formation, we propose a new mechanism for the nitridation of Al particles.

  10. Interstitial Oxide Ion Distribution and Transport Mechanism in Aluminum-Doped Neodymium Silicate Apatite Electrolytes.

    Science.gov (United States)

    An, Tao; Baikie, Tom; Orera, Alodia; Piltz, Ross O; Meven, Martin; Slater, Peter R; Wei, Jun; Sanjuán, María L; White, T J

    2016-04-01

    Rare earth silicate apatites are one-dimensional channel structures that show potential as electrolytes for solid oxide fuel cells (SOFC) due to their high ionic conductivity at intermediate temperatures (500-700 °C). This advantageous property can be attributed to the presence of both interstitial oxygen and cation vacancies, that create diffusion paths which computational studies suggest are less tortuous and have lower activation energies for migration than in stoichiometric compounds. In this work, neutron diffraction of Nd(28+x)/3AlxSi6-xO26 (0 ≤ x ≤ 1.5) single crystals identified the locations of oxygen interstitials, and allowed the deduction of a dual-path conduction mechanism that is a natural extension of the single-path sinusoidal channel trajectory arrived at through computation. This discovery provides the most thorough understanding of the O(2-) transport mechanism along the channels to date, clarifies the mode of interchannel motion, and presents a complete picture of O(2-) percolation through apatite. Previously reported crystallographic and conductivity measurements are re-examined in the light of these new findings. PMID:27015162

  11. Transparent resistive switching memory using aluminum oxide on a flexible substrate

    Science.gov (United States)

    Yeom, Seung-Won; Shin, Sang-Chul; Kim, Tan-Young; Ha, Hyeon Jun; Lee, Yun-Hi; Shim, Jae Won; Ju, Byeong-Kwon

    2016-02-01

    Resistive switching memory (ReRAM) has attracted much attention in recent times owing to its fast switching, simple structure, and non-volatility. Flexible and transparent electronic devices have also attracted considerable attention. We therefore fabricated an Al2O3-based ReRAM with transparent indium-zinc-oxide (IZO) electrodes on a flexible substrate. The device transmittance was found to be higher than 80% in the visible region (400-800 nm). Bended states (radius = 10 mm) of the device also did not affect the memory performance because of the flexibility of the two transparent IZO electrodes and the thin Al2O3 layer. The conduction mechanism of the resistive switching of our device was explained by ohmic conduction and a Poole-Frenkel emission model. The conduction mechanism was proved by oxygen vacancies in the Al2O3 layer, as analyzed by x-ray photoelectron spectroscopy analysis. These results encourage the application of ReRAM in flexible and transparent electronic devices.

  12. Electrode patterning and annealing processes of aluminum-doped zinc oxide thin films using a UV laser system

    Science.gov (United States)

    Hsiao, Wen-Tse; Tseng, Shih-Feng; Huang, Kuo-Cheng; Chiang, Donyau

    2013-01-01

    This study presents the hybrid processing (patterning and annealing) of aluminum-doped zinc oxide (AZO) films in a one-step process using a diode-pumped-solid-state (DPSS) ultraviolet (UV) laser system. The focused laser beam had a diameter of 30 μm and the positive defocused laser beam had a diameter of 1 mm. Both beams were adjusted using a UV laser-processing system. AZO films were deposited on Corning Eagle 2000® optical glass sheets with a thickness of 0.7 mm using a sputtering method. The deposited films were approximately 200 nm. The optoelectronic properties of machined (patterning and annealing) AZO films depend on the laser pulse frequency and galvanometer scanning speed. The surface morphology, roughness, optical transmittance, and resistivity of the films after the laser patterning and annealing processes were measured using a three-dimensional confocal laser scanning microscope, a field emission scanning electron microscope (FE-SEM), a spectrophotometer, and a four-point probe instrument, respectively. Experimental results indicate that the ablation depth increased as the pulse repetition frequency increased. The ablation depth also decreased as the galvanometric scanning speed increased. The transmittance spectra of the film changes slightly after laser annealing, and the average transmittance in the visible region is approximately 83%. All resistivity values of laser-patterned and annealed AZO films decreased significantly. The structural properties grain size was calculated firm the X-ray diffraction (XRD) spectra using the Scherrer equation that increased from 7.4 nm to 12 nm as the annealing scanning speed decreased from 800 mm/s to 400 mm/s. The root mean square (RMS) values of annealed AZO films treated with a laser scanning speed of 500 mm/s with a pulse repetition frequency of 40 kHz, 55 kHz, and 70 kHz were 1.1 nm, 1.2 nm, and 1.8 nm, respectively.

  13. Investigations on opto-electronical properties of DC reactive magnetron sputtered zinc aluminum oxide thin films annealed at different temperatures

    International Nuclear Information System (INIS)

    Highlights: ► ZAO films were prepared by DC reactive magnetron sputtering method by two individual high purity metallic targets of Zn and Al. ► Sputtering deposition conditions were optimized to exhibit a good surface roughness for light scattering and low resistivities. ► A low resistivity of 2.18 × 10−4 Ω cm and mobility of 46 cm2 V−1 s−1 obtained for ZAO film annealed at 400 °C. - Abstract: In the present study transparent conducting zinc aluminum oxide (ZAO) thin films were prepared by DC reactive magnetron sputtering technique. The films were deposited on glass substrates at 200 °C and annealed from 200 °C to 500 °C. XRD patterns of ZAO films shows (0 0 2) diffraction peak of hexagonal wurtzite, meaning that the films have c-axis orientation perpendicular to the substrate. Crystallite size was calculated from X-ray diffraction (XRD) spectra using the Scherrer formula. The surface morphology of the films was observed by field emission scanning electron microscopy (FESEM) and atomic force microscopy (AFM). The electrical conductivity increases with increase of annealing temperature. The activation energies of conduction were obtained from an Arrhenius equation. The best characteristics of ZAO films have been obtained for the films annealed at 400 °C with an average transmittance of 88% and a minimum resistivity of 2.2 × 10−4 Ω cm. The optical band gap, optical constants, and electron concentrations of ZAO films are obtained from UV–vis–IR spectrophotometer data.

  14. Investigations on opto-electronical properties of DC reactive magnetron sputtered zinc aluminum oxide thin films annealed at different temperatures

    Energy Technology Data Exchange (ETDEWEB)

    Kumar, B. Rajesh, E-mail: rajphyind@gmail.com [Department of Physics, Sri Venkateswara University, Tirupati 517502, A.P. (India); Department of Physics, S.K. University, Anantapur 515003, A.P. (India); Rao, T. Subba [Department of Physics, S.K. University, Anantapur 515003, A.P. (India)

    2013-01-15

    Highlights: Black-Right-Pointing-Pointer ZAO films were prepared by DC reactive magnetron sputtering method by two individual high purity metallic targets of Zn and Al. Black-Right-Pointing-Pointer Sputtering deposition conditions were optimized to exhibit a good surface roughness for light scattering and low resistivities. Black-Right-Pointing-Pointer A low resistivity of 2.18 Multiplication-Sign 10{sup -4} {Omega} cm and mobility of 46 cm{sup 2} V{sup -1} s{sup -1} obtained for ZAO film annealed at 400 Degree-Sign C. - Abstract: In the present study transparent conducting zinc aluminum oxide (ZAO) thin films were prepared by DC reactive magnetron sputtering technique. The films were deposited on glass substrates at 200 Degree-Sign C and annealed from 200 Degree-Sign C to 500 Degree-Sign C. XRD patterns of ZAO films shows (0 0 2) diffraction peak of hexagonal wurtzite, meaning that the films have c-axis orientation perpendicular to the substrate. Crystallite size was calculated from X-ray diffraction (XRD) spectra using the Scherrer formula. The surface morphology of the films was observed by field emission scanning electron microscopy (FESEM) and atomic force microscopy (AFM). The electrical conductivity increases with increase of annealing temperature. The activation energies of conduction were obtained from an Arrhenius equation. The best characteristics of ZAO films have been obtained for the films annealed at 400 Degree-Sign C with an average transmittance of 88% and a minimum resistivity of 2.2 Multiplication-Sign 10{sup -4} {Omega} cm. The optical band gap, optical constants, and electron concentrations of ZAO films are obtained from UV-vis-IR spectrophotometer data.

  15. Oxidative Metabolism of Rye (Secale cereale L.) after Short Term Exposure to Aluminum: Uncovering the Glutathione–Ascorbate Redox Network

    Science.gov (United States)

    de Sousa, Alexandra; AbdElgawad, Hamada; Han, Asard; Teixeira, Jorge; Matos, Manuela; Fidalgo, Fernanda

    2016-01-01

    One of the major limitations to plant growth and yield in acidic soils is the prevalence of soluble aluminum ions (Al3+) in the soil solution, which can irreversible damage the root apex cells. Nonetheless, many Al-tolerant species overcome Al toxicity and are well-adapted to acidic soils, being able to complete their life cycle under such stressful conditions. At this point, the complex physiological and biochemical processes inherent to Al tolerance remain unclear, especially in what concerns the behavior of antioxidant enzymes and stress indicators at early plant development. Since rye (Secale cereale L.), is considered the most Al-tolerant cereal, in this study we resort to seedlings of two genotypes with different Al sensitivities in order to evaluate their oxidative metabolism after short term Al exposure. Al-induced toxicity and antioxidant responses were dependent on rye genotype, organ and exposure period. Al affected biomass production and membrane integrity in roots and leaves of the sensitive (RioDeva) genotype. Catalase was the primary enzyme involved in H2O2 detoxification in the tolerant (Beira) genotype, while in RioDeva this task was mainly performed by GPX and POX. Evaluation of the enzymatic and non-enzymatic components of the ascorbate–glutathione cycle, as well the oxalate content, revealed that Beira genotype coped with Al stress by converting DHA into oxalate and tartarate, which posteriorly may bind to Al forming non-toxic chelates. In contrast, RioDeva genotype used a much more ineffective strategy which passed through ascorbate regeneration. So, remarkable differences between MDHAR and DHAR activities appear to be the key for a higher Al tolerance. PMID:27252711

  16. Modification of oxide inclusions present in aluminum-killed low carbon steel by addition of calcium

    Directory of Open Access Journals (Sweden)

    José Carlos S. Pires

    2004-09-01

    Full Text Available A crescente demanda por aços de alta qualidade com elevada limpeza interna tem levado a uma contínua melhoria nas práticas de produção do aço, em especial na etapa de refino secundário. O interesse especial é no controle das inclusões não-metálicas, devido ao seu efeito prejudicial nas etapas subseqüentes (lingotamento e conformação plástica e devido às sua grande influência nas propriedades do produto final. Através do controle do tamanho, da quantidade e da composição química das inclusões, é possível obter um produto final de alta qualidade. O controle da formação das inclusões não-metálicas e a identificação de suas fases constituintes são de suma importância para a obtenção de aços limpos. Nesse trabalho, amostras de aço de baixo teor de carbono, desoxidado ao silício, coletadas em uma indústria siderúrgica, são analisadas e é demonstrado que, pela comparação do teor total de cálcio e de oxigênio no aço, é possível prever os tipos de inclusões presentes no aço.The increasing demand in recent years for high-quality steel products has led to the continuous improvement of steelmaking practices. There is a special interest in the control of non-metallic inclusions due to their harmful effect on the subsequent stages and their great influence on the properties of the final product. Through the control of the amount, size and chemical composition of the inclusions it is possible to obtain a final product of good quality. The control of the formation of non-metallic inclusions and the identification of their constituent phases are of extreme importance for the obtaining of clean steels. In this work, samples collected in a steelmaking process are analyzed and it is demonstrated that by comparing the total calcium and oxygen contents in the steel, it is possible to have an overview of the types of oxide inclusions present.

  17. 铝合金微弧氧化技术研究概况%Research situation of micro-arc oxidation of aluminum alloys

    Institute of Scientific and Technical Information of China (English)

    石小超; 陈朝章; 徐晋勇; 高成; 王贵

    2012-01-01

    综述了铝合金微弧氧化技术的原理及陶瓷膜的特点.着重分析总结电流密度、电压与频率、占空比等电参量因素对陶瓷膜性能的影响,介绍铝合金微弧氧化中常用的电解液组成,简要描述微弧氧化陶瓷膜的硬度、耐磨、断裂、耐腐蚀等性能.%Treatment principle of aluminum alloy and the formation characteristics of the ceramic membrane by micro - arc oxidation (MAO) technique are reviewed. The effects of electrical parameters, such as current density, voltage and frequency, duty cycle on the performance of micro - arc oxidation ceramic coating are emphasized. Electrolyte composition of micro - arc oxidation on aluminum alloys is introduced. The hardness, wear resistance, fracture resistance, corrosion resistance and other properties of the micro-arc oxidation ceramic coating are briefly described.

  18. Fabrication of CoPd alloy nanowire arrays on an anodic aluminum oxide/Ti/Si substrate and their enhanced magnetic properties

    International Nuclear Information System (INIS)

    An anodic aluminum oxide/Ti/Si substrate was successfully synthesized by the anodization of an aluminum film on a Ti/Si substrate and then used as a template to grow 10 nm diameter CoPd alloy nanowires. X-ray diffraction and energy-dispersed X-ray patterns indicated that Co0.97Pd0.03 nanowire arrays with a preferential orientation of (0 0 2) were formed during electrodeposition. High coercivity (about 1700 Oe) and squareness (about 0.85) were obtained in the samples when the magnetic field was applied parallel to the axis of the nanowires; these values are much larger than those of pure Co nanowire arrays with the same diameters

  19. Magnetron sputtering of silver nanowires using anodic aluminum oxide template: a new active substrate of surface enhanced Raman scattering and an investigation of its enhanced mechanism.

    Science.gov (United States)

    Zhang, Lisheng; Zhang, Pengxiang; Fang, Yan

    2007-05-22

    A high quality anodic aluminum oxide (AAO) template with ordered apertures about 50-80 nm was fabricated by anodizing aluminum in electrolytes through a two-step method, and silver nanowires with diameters from 40 nm to 70 nm were prepared on this AAO template by magnetron sputtering. On the glass covered with silver nanowires, high quality surface enhanced Raman scattering (SERS) spectra of sudan II (C18H16N2O) with enhancement factors of 10(5) were obtained. And comparison of SERS spectra on silver nanowires with the SERS spectra of silver colloids indicates that main enhanced mode is lightning rod effect of nanorods on the Sudan II/silver nanowires system. PMID:17481411

  20. Metal Ion Imbalance-Related Oxidative Stress Is Involved in the Mechanisms of Liver Injury in a Rat Model of Chronic Aluminum Exposure.

    Science.gov (United States)

    Yang, Yang; Wang, Hong; Guo, Yuanxin; Lei, Wenjuan; Wang, Jianfeng; Hu, Xinyue; Yang, Junqing; He, Qin

    2016-09-01

    The objective of the study is to investigate the effects of chronic aluminum overload on rat liver function and its induction of pathological changes in metal ion levels and oxidative stress in hepatic tissues. Wistar rats were intragastrically administered aluminum gluconate (200 mg Al(3+)/Kg) once a day, 5 days a week, for 20 weeks. HE staining was used to visualize pathological changes in rat liver tissue. A biochemical method was adopted to detect ALT, AST, ALP, and GGT levels, as well as liver SOD activity and blood plasma MDA content. A plasma atomic emission spectrophotometer was used to detect Al, Mn, Fe, Zn, and Cu ion contents in liver tissue. Our results showed obvious vacuolar degeneration, granular degeneration, and spotty necrosis in chronic Al-overload rat hepatocytes. The levels of ALT, AST, ALP, and GGT were significantly increased. Liver SOD activity was significantly decreased, and MDA content was significantly increased. In Al-overload rat liver, Al, Mn, Fe, and Cu contents were significantly increased, and in Al-overload rat serum, Mn, Fe, Zn, and Cu contents were significantly decreased. However, the Al level in Al-overload rat serum was not significantly different from that in control rat serum. These results suggest that chronic aluminum overload causes obvious damage to rat liver and causes imbalances in Al, Mn, Fe, Zn, and Cu levels in rat liver and serum. Metal ion imbalance-related oxidative stress may be involved in the mechanism of chronic liver injury caused by aluminum overload. PMID:26811106

  1. Oxide film microstructure: the link between surface preparation processes and strength/durability of adhesively bonded aluminum. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Hsia, K. Jimmy; Pearlstein, Arne J.; Scheeline, Alexander; Shang, Jian Ku

    2000-11-30

    Strength and durability of adhesive bonding of aluminum alloys structures are intrinsically determined by the surface microstructures and interfacial failure micromechanisms. The current project presents a multidisciplinary approach to addressing critical issues controlling the strength and durability of adhesive bonds of aluminum alloys. Three main thrust areas have been pursued: surface treatment technology development to achieve desirable surface microstructures; relationship between surface structure and properties of adhesive bonds; and failure mechanisms of adhesively bonded components.

  2. Mechanical behavior of shock-wave consolidated nano and micron-sized aluminum/silicon carbide and aluminum/aluminum oxide two-phase systems characterized by light and electron metallography

    Science.gov (United States)

    Alba-Baena, Noe Gaudencio

    This dissertation reports the results of the exploratory study of two-phase systems consisting of 150 microm diameter aluminum powder mechanically mixed with 30 nm and 30 microm diameter SiC and Al2O3 powders (in volume fractions of 2, 4, and 21 percent). Powders were mechanically mixed and green compacted to ˜80% theorical density in a series of cylindrical fixtures (steel tubes). The compacted arrangements were explosively consolidated using ammonium nitrate-fuel oil (ANFO) to form stacks of two-phase systems. As result, successfully consolidated cylindrical monoliths of 50 mm (height) x 32 mm (in diameter) were obtained. By taking advantage of the use of SWC (shock wave consolidation) and WEDM (wire-electric discharge machining), the heterogeneous systems were machined in a highly efficiency rate. The sample cuts used for characterization and mechanical properties testing, require the use of less that 10cc of each monolith, in consequence there was preserved an average of 60% of the obtained system monoliths. Consolidated test cylinders of the pure Al and two-phase composites were characterized by optical metallography and TEM. The light micrographs for the five explosively consolidated regimes: aluminum powder, nano and micron-sized Al/Al2O3 systems, and the nano and micron-sized Al/SiC systems exhibit similar ductility in the aluminum grains. Low volume fraction systems exhibit small agglomerations at the grain boundaries for the Al/Al2O3 system and the Al/SiC system reveal a well distributed phase at the grain boundaries. Large and partially bonded agglomerations were observable in the nano-sized high volume fraction (21%) systems, while the micron-sized Al/ceramic systems exhibit homogeneous distribution along the aluminum phase grains. TEM images showed the shock-induced dislocation cell structure, which has partially recrystallized to form a nano grain structure in the consolidated aluminum powder. Furthermore, the SiC nano-agglomerates appeared to have

  3. Aluminum microstructures on anodic alumina for aluminum wiring boards.

    Science.gov (United States)

    Jha, Himendra; Kikuchi, Tatsuya; Sakairi, Masatoshi; Takahashi, Hideaki

    2010-03-01

    The paper demonstrates simple methods for the fabrication of aluminum microstructures on the anodic oxide film of aluminum. The aluminum sheets were first engraved (patterned) either by laser beam or by embossing to form deep grooves on the surface. One side of the sheet was then anodized, blocking the other side by using polymer mask to form the anodic alumina. Because of the lower thickness at the bottom part of the grooves, the part was completely anodized before the complete oxidation of the other parts. Such selectively complete anodizing resulted in the patterns of metallic aluminum on anodic alumina. Using the technique, we fabricated microstructures such as line patterns and a simple wiring circuit-board-like structure on the anodic alumina. The aluminum microstructures fabricated by the techniques were embedded in anodic alumina/aluminum sheet, and this technique is promising for applications in electronic packaging and devices. PMID:20356280

  4. Microstructure trends in metal (aluminum, copper, indium, lead, tin)-metal oxide thin films prepared by reactive ion beam sputter deposition

    International Nuclear Information System (INIS)

    Transmission electron microscopy has bee used to study the microstructural trends of thin film composites prepared by sputtering of a metal (aluminum, copper, indium, lead or tin) target with argon ions in the presence of a reactive gas (oxygen). Results of these studies reveal that there is a general progression in the metal component microstructure which correlates with an increasing metal oxide component in the films and can be classified as belonging to an agglomerated-columnar-granular-amorphous sequence. These structural trends and the concomitant effect on film properties, such as resistivity, adhesion and mechanical stability, are a direct consequence of the metal-metal oxide interaction and the inhibiting effect which the native metal oxides have on metal atom diffusion during film formation. (Auth.)

  5. Evolution of insoluble eutectic Si particles in anodic oxidation films during adipic-sulfuric acid anodizing processes of ZL114A aluminum alloys

    Science.gov (United States)

    Hua, Lei; Liu, Jian-hua; Li, Song-mei; Yu, Mei; Wang, Lei; Cui, Yong-xin

    2015-03-01

    The effects of insoluble eutectic Si particles on the growth of anodic oxide films on ZL114A aluminum alloy substrates were investigated by optical microscopy (OM) and scanning electron microscopy (SEM). The anodic oxidation was performed at 25°C and a constant voltage of 15 V in a solution containing 50 g/L sulfuric acid and 10 g/L adipic acid. The thickness of the formed anodic oxidation film was approximately 7.13 μm. The interpore distance and the diameters of the major pores in the porous layer of the film were within the approximate ranges of 10-20 nm and 5-10 nm, respectively. Insoluble eutectic Si particles strongly influenced the morphology of the anodic oxidation films. The anodic oxidation films exhibited minimal defects and a uniform thickness on the ZL114A substrates; in contrast, when the front of the oxide oxidation films encountered eutectic Si particles, defects such as pits and non-uniform thickness were observed, and pits were observed in the films.

  6. Aluminum Hydroxide

    Science.gov (United States)

    Aluminum hydroxide is used for the relief of heartburn, sour stomach, and peptic ulcer pain and to ... Aluminum hydroxide comes as a capsule, a tablet, and an oral liquid and suspension. The dose and ...

  7. Low temperature solid oxide fuel cells with proton-conducting Y:BaZrO3 electrolyte on porous anodic aluminum oxide substrate

    International Nuclear Information System (INIS)

    This paper presents the architecture of a nano thin-film yttrium-doped barium zirconate (BYZ) solid-oxide fuel cell that uses nanoporous anodic aluminum oxide (AAO) as a supporting and gas-permeable substrate. The anode was fabricated by sputtering 300 nm platinum thin film that partially covered the AAO surface pores, followed by an additional conformal platinum coating to tune the pore size by atomic layer deposition. Two different nano-porous anode structures with a pore size of 10 nm or 50 nm were deposited. Proton-conducting BYZ ceramic electrolyte with increasing thicknesses of 300, 600, and 900 nm was deposited on top of the platinum anode by pulsed laser deposition, followed by a 200 nm layer of porous Pt sputtered on BYZ electrolyte as a cathode. The open circuit voltage (OCV) of the fuel cells was characterized at 250 °C with 1:1 volumetric stoichiometry of a methanol/water vapor mixture as the fuel. The OCVs were 0.17 V with a 900 nm-thick BYZ electrolyte on 50 nm pores and 0.3 V with a 600 nm-thick BYZ electrolyte on 10 nm pores, respectively, but it increased to 0.8 V for a 900 nm-thick BYZ electrolyte on 10 nm pores, indicating that increasing the film thickness and decreasing a surface pore size help to reduce the number of electrolyte pinholes and the gas leakage through the electrolyte. A maximum power density of 5.6 mW/cm2 at 250 °C was obtained from the fuel cell with 900 nm of BYZ electrolyte using methanol vapor as a fuel. - Highlights: • A low temperature ceramic fuel cell on nano-porous substrate was demonstrated. • A thin-film yttrium doped barium zirconate (BYZ) was deposited as an electrolyte. • An open circuit voltage (OCV) was measured to verify the BYZ film quality. • An OCV increased by increasing BYZ film thickness and decreasing pore size of anode. • The current–voltage performance was measured using vaporized methanol fuel at 250 °C

  8. DUPLEX Al2O3/DLC COATING ON 15SiCp/2024 ALUMINUM MATRIX COMPOSITE USING COMBINED MICROARC OXIDATION AND FILTERED CATHODIC VACUUM ARC DEPOSITION

    OpenAIRE

    WENBIN XUE; HUA TIAN; JIANCHENG DU; MING HUA; XU ZHANG; YONGLIANG LI

    2012-01-01

    Microarc oxidation (MAO) treatment produces a thick Al2O3 coating on the 15SiCp/2024 aluminum matrix composite. After pretreatment of Ti ion implantation, a thin diamond-like carbon film (DLC) was deposited on the top of polished Al2O3 coating by a pulsed filtered cathodic vacuum arc (FCVA) deposition system with a metal vapor vacuum arc (MEVVA) source. The morphology and tribological properties of the duplex Al2O3/DLC multiplayer coating were investigated by Raman spectroscopy, scanning elec...

  9. Study on Light Extraction from GaN-based Green Light-Emitting Diodes Using Anodic Aluminum Oxide Pattern and Nanoimprint Lithography

    OpenAIRE

    Shengxiang Jiang; Yulong Feng; Zhizhong Chen; Lisheng Zhang; Xianzhe Jiang; Qianqian Jiao; Junze Li; Yifan Chen; Dongsan Li; Lijian Liu; Tongjun Yu; Bo Shen; Guoyi Zhang

    2016-01-01

    An anodic aluminum oxide (AAO) patterned sapphire substrate, with the lattice constant of 520 ± 40 nm, pore dimension of 375 ± 50 nm, and height of 450 ± 25 nm was firstly used as a nanoimprint lithography (NIL) stamp and imprinted onto the surface of the green light-emitting diode (LED). A significant light extraction efficiency (LEE) was improved by 116% in comparison to that of the planar LED. A uniform broad protrusion in the central area and some sharp lobes were also obtained in the ang...

  10. Research on manufacturing aluminum - rare earth alloy with a high content of rare earth (> 20% RE) from total rare earth oxides by thermit reduction

    International Nuclear Information System (INIS)

    In this report, several theoretical principles of thermit reduction method used for metal oxides to obtain metals, ferroalloys and ligatua with technical purity are presented. Manufacture of aluminum-rare earth alloys by thermit reduction is also described in the report. Data that are generalized based on thermo-kinetic calculation of the thermit reduction and selection of technological flow-sheet based on thermal effect will partly clarify research results in investigating typical features of the process and identify measures to reduce metal loss in discharged slags. (author)

  11. Influence of Gas Composition and Exposure Cycle on the Formation of Surface and Subsurface Oxides in Iron-Aluminum-Based Alloys at High Temperatures

    Science.gov (United States)

    Bott, June H.; Yin, Hogbin; Sridhar, Seetharaman; Auinger, Michael

    2016-04-01

    The slab reheating process of binary iron-aluminum alloys and an industrial TRIP steel grade has been investigated in both dry and wet atmospheres. The presence of water vapor has a significant effect on the overall scale growth and internal corrosion depth. Heating rate greatly influences the porosity of the surface oxide layer with the surface getting more porous at faster heating rates. Nitride formation could be suppressed in the presence of water vapor, leading to a reduction of internal corrosion depth and a better formability of the final material. Experimental results were compared to thermodynamic predictions and critically discussed.

  12. Dispersion fraction enhances cellular growth of carbon nanotube and aluminum oxide reinforced ultrahigh molecular weight polyethylene biocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Patel, Anup Kumar; Balani, Kantesh, E-mail: kbalani@iitk.ac.in

    2015-01-01

    Ultrahigh molecular weight polyethylene (UHMWPE) is widely used as bone-replacement material for articulating surfaces due to its excellent wear resistance and low coefficient of friction. But, the wear debris, generated during abrasion between mating surfaces, leads to aseptic loosening of implants. Thus, various reinforcing agents are generally utilized, which may alter the surface and biological properties of UHMWPE. In the current work, the cellular response of compression molded UHMWPE upon reinforcement of bioactive multiwalled carbon nanotubes (MWCNTs) and bioinert aluminum oxide (Al{sub 2}O{sub 3}) is investigated. The phase retention and stability were observed using X-ray diffraction, Raman spectroscopy and Fourier transform infrared (FTIR) spectroscopy. The reinforcement of MWCNTs and Al{sub 2}O{sub 3} has shown to alter the wettability (from contact angle of ∼ 88° ± 2° to ∼ 118° ± 4°) and surface energy (from ∼ 23.20 to ∼ 17.75 mN/m) of composites with respect to UHMWPE, without eliciting any adverse effect on cytocompatibility for the L929 mouse fibroblast cell line. Interestingly, the cellular growth of the L929 mouse fibroblast cell line is observed to be dominated by the dispersion fraction of surface free energy (SFE). After 48 h of incubation period, a decrease in metabolic activity of MWCNT–Al{sub 2}O{sub 3} reinforced composites is attributed to apatite formation that reduces the dispersion fraction of surface energy. The mineralized apatite during incubation was confirmed and quantified by energy dispersive spectroscopy and X-ray diffraction respectively. Thus, the dispersion fraction of surface free energy can be engineered to play an important role in achieving enhanced metabolic activity of the MWCNT–Al{sub 2}O{sub 3} reinforced UHMWPE biopolymer composites. - Highlights: • The cellular response of UHMWPE upon MWCNT and Al{sub 2}O{sub 3} reinforcement is highlighted. • Wettability decreases with Al{sub 2}O{sub 3} and

  13. Dispersion fraction enhances cellular growth of carbon nanotube and aluminum oxide reinforced ultrahigh molecular weight polyethylene biocomposites

    International Nuclear Information System (INIS)

    Ultrahigh molecular weight polyethylene (UHMWPE) is widely used as bone-replacement material for articulating surfaces due to its excellent wear resistance and low coefficient of friction. But, the wear debris, generated during abrasion between mating surfaces, leads to aseptic loosening of implants. Thus, various reinforcing agents are generally utilized, which may alter the surface and biological properties of UHMWPE. In the current work, the cellular response of compression molded UHMWPE upon reinforcement of bioactive multiwalled carbon nanotubes (MWCNTs) and bioinert aluminum oxide (Al2O3) is investigated. The phase retention and stability were observed using X-ray diffraction, Raman spectroscopy and Fourier transform infrared (FTIR) spectroscopy. The reinforcement of MWCNTs and Al2O3 has shown to alter the wettability (from contact angle of ∼ 88° ± 2° to ∼ 118° ± 4°) and surface energy (from ∼ 23.20 to ∼ 17.75 mN/m) of composites with respect to UHMWPE, without eliciting any adverse effect on cytocompatibility for the L929 mouse fibroblast cell line. Interestingly, the cellular growth of the L929 mouse fibroblast cell line is observed to be dominated by the dispersion fraction of surface free energy (SFE). After 48 h of incubation period, a decrease in metabolic activity of MWCNT–Al2O3 reinforced composites is attributed to apatite formation that reduces the dispersion fraction of surface energy. The mineralized apatite during incubation was confirmed and quantified by energy dispersive spectroscopy and X-ray diffraction respectively. Thus, the dispersion fraction of surface free energy can be engineered to play an important role in achieving enhanced metabolic activity of the MWCNT–Al2O3 reinforced UHMWPE biopolymer composites. - Highlights: • The cellular response of UHMWPE upon MWCNT and Al2O3 reinforcement is highlighted. • Wettability decreases with Al2O3 and MWCNT reinforcement without any adverse effect on cytocompatibility.

  14. Investigation of the weldability of iron-aluminum-chromium overlay coatings for corrosion protection in oxidizing/sulfidizing environments

    Science.gov (United States)

    Regina, Jonathan R.

    The current study investigated the effect of chromium additions on the hydrogen cracking susceptibility of Fe-Al weld overlay claddings containing chromium additions. It was found that the weldability of FeAlCr claddings was a function of both the aluminum and chromium concentrations of the weld coatings. Weld overlay compositions that were not susceptible to hydrogen cracking were identified and the underlying mechanism behind the hydrogen cracking phenomenon was investigated further. It was concluded that the cracking behavior of the FeAlCr welds depended strongly on the microstructure of the weld fusion zone. Although it was found that the cracking susceptibility was influenced by the presence of Fe-Al intermetallic phases (namely Fe3 Al and FeAl), the cracking behavior of FeAlCr weld overlay claddings also depended on the size and distribution of carbide and oxide particles present within the weld structure. These particles acted as hydrogen trapping sites, which are areas where free hydrogen segregates and can no longer contribute to the hydrogen embrittlement of the metal. It was determined that in practical applications of these FeAlCr weld overlay coatings, carbon should be present within these welds to reduce the amount of hydrogen available for hydrogen cracking. Based on the weldability results of the FeAlCr weld claddings, coating compositions that were able to be deposited crack-free were used for long-term corrosion testing in a simulated low NOx environment. These alloys were compared to a Ni-based superalloy (622), which is commonly utilized as boiler tube coatings in power plant furnaces for corrosion protection. It was found that the FeAlCr alloys demonstrated superior corrosion resistance when compared to the Ni-based superalloy. Due to the excellent long-term corrosion behavior of FeAlCr weld overlays that were immune to hydrogen cracking, it was concluded that select FeAlCr weld overlay compositions would make excellent corrosion resistant

  15. High-temperature CO2 capture cycles of hydrated limestone prepared with aluminum (hydr)oxides derived from kaolin

    International Nuclear Information System (INIS)

    Highlights: • Hydrated limestone exhibited a higher reactivity and stability. • Microstructure of hydrated limestone was significantly improved. • Hydrated limestone still suffered less loss-incapacity. • Hydrated limestone sorbents with kaolin-based binders were prepared and characterized. • Sorbents prepared from hydrated limestone and Al(OH)3 binder are a promising sorbent. - Abstract: A simple and convenient process was used to improve the utilization of natural limestone and kaolin for calcium looping technology and environmental applications. The calcined natural limestone modified with the distilled water (denoted as Limestone-W), was systematically studied and compared with the other CaO sorbents (calcium acetate, calcium D-gluconate and calcined natural limestone). These CaO-based sorbents were tested for their CO2 capture behavior through 20 carbonation/calcination cycles in a thermo-gravimetric analyzer (TGA). Their morphology, pore structure and phase composition before and after carbonation/calcination cycles were determined by scanning electron microscopy, nitrogen adsorption, and X-ray diffraction. The first-cycle and multicycle sorption results revealed that the Limestone-W sorbent exhibited a relatively faster reaction rate and higher cyclic CO2 capture. The characterization data indicated that the Limestone-W was composed of a special calcium oxide structure with lower crystalline and higher porosity nanoparticles, which appeared to be the main reasons for its higher CO2 capture capability. However, the Limestone-W still suffered loss of reactivity, even though it was less pronounced than the other CaO sorbent. To avoid this unfavorable effect, a thermally stable inert material (aluminum hydroxide derived from kaolin) was incorporated into the Limestone-W structure. This new sorbent revealed higher stability because the formation of a stable framework of Ca12Al14O33 particles hindered densification and sintering of the CaO phase. It was

  16. Analysis of chemical dissolution of the barrier layer of porous oxide on aluminum thin films using a re-anodizing technique

    International Nuclear Information System (INIS)

    Chemical dissolution of the barrier layer of porous oxide formed on thin aluminum films (99.9% purity) in the 4% oxalic acid after immersion in 2 mol dm-3 sulphuric acid at 50 deg. C has been studied. The barrier layer thickness before and after dissolution was calculated using a re-anodizing technique. It has been shown that above 57 V the change in the growth mechanism of porous alumina films takes place. As a result, the change in the amount of regions in the barrier oxide with different dissolution rates is observed. The barrier oxide contains two layers at 50 V: the outer layer with the highest dissolution rate and the inner layer with a low dissolution rate. Above 60 V the barrier oxide contains three layers: the outer layer with a high dissolution rate, the middle layer with the highest dissolution rate and the inner layer with a low dissolution rate. We suggest that the formation of the outer layer of barrier oxide with a high dissolution rate is linked with the injection of protons or H3O+ ions from the electrolyte into the oxide film at the anodizing voltages above 57 V

  17. NaCl盐膜对铝青铜高温氧化行为的影响%Effect of NaCl Film on Oxidation Behavior of Aluminum Bronze at High Temperature

    Institute of Scientific and Technical Information of China (English)

    李占鑫

    2009-01-01

    采用金相检验、X射线衍射、扫描电镜/能谱及热重分析法研究了涂有NaCl盐膜的铝青铜在700~900℃的氧化行为.结果表明,在NaCl盐膜的作用下,铝青铜中的铝较铜先腐蚀,所形成的氧化膜结构疏松,易开裂和剥落,从而加速铝的氧化过程.此外,还讨论了NaCl加速铝青铜氧化的机制.%The oxidation behavior of aluminum bronze coated with a NaCl film was studied by means of metallosco-py,XRD,SEM/EDS and thermogravimetry. The results show that because of the effect of NaCl film the aluminum will be eroded earlier than the copper in aluminum bronze and the oxide film produced will be loose and easy to crack and spall, with the oxidation of aluminum bronze accelerated. In addition, the mechanism for NaCl film to ac-celerate the oxidation of aluminum bronze was discussed, too.

  18. Preparation of thin hexagonal highly-ordered anodic aluminum oxide (AAO) template onto silicon substrate and growth ZnO nanorod arrays by electrodeposition

    Science.gov (United States)

    Chahrour, Khaled M.; Ahmed, Naser M.; Hashim, M. R.; Elfadill, Nezar G.; Qaeed, M. A.; Bououdina, M.

    2014-12-01

    In this study, anodic aluminum oxide (AAO) templates of Aluminum thin films onto Ti-coated silicon substrates were prepared for growth of nanostructure materials. Hexagonally highly ordered thin AAO templates were fabricated under controllable conditions by using a two-step anodization. The obtained thin AAO templates were approximately 70 nm in pore diameter and 250 nm in length with 110 nm interpore distances within an area of 3 cm2. The difference between first and second anodization was investigated in details by in situ monitoring of current-time curve. A bottom barrier layer of the AAO templates was removed during dropping the voltage in the last period of the anodization process followed by a wet etching using phosphoric acid (5 wt%) for several minutes at ambient temperature. As an application, Zn nanorod arrays embedded in anodic alumina (AAO) template were fabricated by electrodeposition. Oxygen was used to oxidize the electrodeposited Zn nanorods in the AAO template at 700 °C. The morphology, structure and photoluminescence properties of ZnO/AAO assembly were analyzed using Field-emission scanning electron microscope (FESEM), Energy dispersive X-ray spectroscopy (EDX), Atomic force microscope (AFM), X-ray diffraction (XRD) and photoluminescence (PL).

  19. Nanoporous anodic aluminum oxide with a long-range order and tunable cell sizes by phosphoric acid anodization on pre-patterned substrates

    Science.gov (United States)

    Surawathanawises, Krissada; Cheng, Xuanhong

    2014-01-01

    Nanoporous anodic aluminum oxide (AAO) has been explored for various applications due to its regular cell arrangement and relatively easy fabrication processes. However, conventional two-step anodization based on self-organization only allows the fabrication of a few discrete cell sizes and formation of small domains of hexagonally packed pores. Recent efforts to pre-pattern aluminum followed with anodization significantly improve the regularity and available pore geometries in AAO, while systematic study of the anodization condition, especially the impact of acid composition on pore formation guided by nanoindentation is still lacking. In this work, we pre-patterned aluminium thin films using ordered monolayers of silica beads and formed porous AAO in a single-step anodization in phosphoric acid. Controllable cell sizes ranging from 280 nm to 760 nm were obtained, matching the diameters of the silica nanobead molds used. This range of cell size is significantly greater than what has been reported for AAO formed in phosphoric acid in the literature. In addition, the relationships between the acid concentration, cell size, pore size, anodization voltage and film growth rate were studied quantitatively. The results are consistent with the theory of oxide formation through an electrochemical reaction. Not only does this study provide useful operational conditions of nanoindentation induced anodization in phosphoric acid, it also generates significant information for fundamental understanding of AAO formation. PMID:24535886

  20. The effect of oxygen source on atomic layer deposited Al2O3 as blocking oxide in metal/aluminum oxide/nitride/oxide/silicon memory capacitors

    International Nuclear Information System (INIS)

    This work explores the electrical properties of Al2O3 films formed by atomic layer deposition (ALD) using different oxygen sources (water and ozone) and trimethylaluminium (TMA). The as-deposited Al2O3 layers were used as blocking oxides in metal (Pt)–alumina–nitride–oxide–silicon memory capacitors. The capacitance–voltage characteristics of the devices with Al2O3 deposited with the ozone–TMA and water–TMA processes showed almost identical capacitance equivalent thicknesses in accordance with transmission electron microscopy imaging which revealed similar dielectric layer thicknesses between the two gate stacks. At high negative gate voltages the water-TMA devices exhibited higher leakage currents than the ozone-TMA devices. This effect had a direct impact on the attainable memory window, due to the limited erase performance of the capacitors and the extended erase-saturation effect. These findings indicate that the ALD chemistry and in particular the oxygen source is a crucial factor which determines the electrical behavior of the as-deposited Al2O3 films, and therefore the performance of the memory stacks. These differences are attributed to the different trap distributions either in space or energy within the Al2O3 layers. - Highlights: ► Al2O3 films were formed by atomic layer deposition using H2O and O3 as oxygen sources. ► Al2O3 layers were used as blocking oxides in charge trapping memory capacitors. ► At high negative voltages, H2O-based samples exhibit higher leakage current density. ► The H2O-based samples have a limited ability to remove trapped electrons. ► Oxygen source differentiates the electrical behavior of as-deposited Al2O3 layers

  1. Evidências da formação de monocamada de óxido de alumínio sobre sílica, através de reações de enxerto Evidence of aluminum oxide monolayer formation on a silica gel surface using grafting reactions

    Directory of Open Access Journals (Sweden)

    Julia M. D. Cónsul

    2005-06-01

    Full Text Available Aluminum oxide was dispersed on a commercial silica gel surface, using successive grafting reactions. The reaction products were characterized by N2 adsorption-desorption isotherms, scanning electron microscopy and infrared spectroscopy. The progressive incorporation of aluminum, up to 5.5% (w/w, does not produce agglomeration of alumina, since changes in the original pore size distribution of the silica matrix were not observed. The aluminum oxide covers homogeneously the silica surface.

  2. Influence of pulsed mechanical activation of hematite-graphite-aluminum powder mixtures on the reduction of iron oxides

    Science.gov (United States)

    Bodrova, L. E.; Vatolin, N. A.; Pastukhov, E. A.; Petrova, S. A.; Popova, E. A.; Zakharov, R. G.

    2011-11-01

    To decrease the temperature of direct iron reduction by carbon and aluminum, short-term pulsed mechanical activation (PMA) of an Fe2O3 + Cgr + Al powder mixture is perfumed during sound-frequency shock loading by a flat activating plunger. The PMA efficiency for powders in comparable with mechanical activation in high-energy ball mills in a decrease in the activation time and retaining the chemical purity of a powder composition.

  3. Modeling and Predicting the Effect of Surface Oxidation on the Normal Spectral Emissivity of Aluminum 5052 at 800 K to 910 K

    Science.gov (United States)

    Shi, Deheng; Zou, Fenghui; Zhu, Zunlue; Sun, Jinfeng

    2016-01-01

    In this study, we tried to develop a model to predict the effect of surface oxidization on the normal spectral emissivity of aluminum 5052 at a temperature range of 800 to 910 K and wavelength of 1.5 \\upmu m. In experiments, specimens were heated in air for 6 h at certain temperatures. Two platinum-rhodium thermocouples were symmetrically welded onto the front surface of the specimens near the measuring area for accurate monitoring of the temperature at the specimen surface. The temperatures measured by the two thermocouples had an uncertainty of 1 K. The normal spectral emissivity values were measured over the 6-h heating period at temperatures from 800 K to 910 K in increments of 10 K. Strong oscillations in the normal spectral emissivity were observed at each temperature. These oscillations were determined to form by the interference between the radiation stemming from the oxide layer and radiation from the substrate. The present measurements were compared with previous experimental results, and the variation in the normal spectral emissivity at given temperatures was evaluated. The uncertainty of the normal spectral emissivity caused only by the surface oxidization was found to be approximately 12.1 % to 21.8 %, and the corresponding uncertainty in the temperature caused only by the surface oxidization was approximately 9.1 K to 15.2 K. The model can reproduce the normal spectral emissivity well, including the strong oscillations that occur during the initial heating period.

  4. The disruption of L-carnitine metabolism by aluminum toxicity and oxidative stress promotes dyslipidemia in human astrocytic and hepatic cells.

    Science.gov (United States)

    Lemire, Joseph; Mailloux, Ryan; Darwich, Rami; Auger, Christopher; Appanna, Vasu D

    2011-06-24

    L-Carnitine is a critical metabolite indispensable for the metabolism of lipids as it facilitates fatty acid transport into the mitochondrion where β-oxidation occurs. Human astrocytes (CCF-STTG1 cells) and hepatocytes (HepG2 cells) exposed to aluminum (Al) and hydrogen peroxide (H₂O₂), were characterized with lower levels of L-carnitine, diminished β-oxidation, and increased lipid accumulation compared to the controls. γ-Butyrobetainealdehyde dehydrogenase (BADH) and butyrobetaine dioxygenase (BBDOX), two key enzymes mediating the biogenesis of L-carnitine, were sharply reduced during Al and H₂O₂ challenge. Exposure of the Al and H₂O₂-treated cells to α-ketoglutarate (KG), led to the recovery of L-carnitine production with the concomitant reduction in ROS levels. It appears that the channeling of KG to combat oxidative stress results in decreased L-carnitine synthesis, an event that contributes to the dyslipidemia observed during Al and H₂O₂ insults in these mammalian cells. Hence, KG may help alleviate pathological conditions induced by oxidative stress. PMID:21439360

  5. Decontamination of discharged aluminum brass condenser tubes of a BWR. Evolving the chemical formulation for copper oxide dissolution

    International Nuclear Information System (INIS)

    Chemical formulations for copper oxide dissolution have been evaluated primarily for the minimum ionic load resulting in the spent formulation along with other desirable qualities. Peroxydisulfuric acid prepared freshly through ion exchange route has shown almost stoichiometric dissolution of the copper oxide as per the acidic oxidative action with efficient kinetics. Stability of the prepared formulation for its application and its effective oxidizing behaviour and aqueous cupric ion stabilizing by its redox product has been established experimentally. (author)

  6. Duplex Al2O3/DLC Coating on 15SiCp/2024 Aluminum Matrix Composite Using Combined Microarc Oxidation and Filtered Cathodic Vacuum Arc Deposition

    Science.gov (United States)

    Xue, Wenbin; Tian, Hua; Du, Jiancheng; Hua, Ming; Zhang, Xu; Li, Yongliang

    2012-08-01

    Microarc oxidation (MAO) treatment produces a thick Al2O3 coating on the 15SiCp/2024 aluminum matrix composite. After pretreatment of Ti ion implantation, a thin diamond-like carbon film (DLC) was deposited on the top of polished Al2O3 coating by a pulsed filtered cathodic vacuum arc (FCVA) deposition system with a metal vapor vacuum arc (MEVVA) source. The morphology and tribological properties of the duplex Al2O3/DLC multiplayer coating were investigated by Raman spectroscopy, scanning electron microscopy (SEM) and SRV ball-on-disk friction tester. It is found that the duplex Al2O3/DLC coating had good adhesion and a low friction coefficient of less than 0.07. As compared to a single Al2O3 or DLC coating, the duplex Al2O3/DLC coating on aluminum matrix composite exhibited a better wear resistance against ZrO2 ball under dry sliding, because the Al2O3 coating as an intermediate layer improved load support for the top DLC coating on 15SiCp/2024 composite substrate, meanwhile the top DLC coating displayed low friction coefficient.

  7. Thermal Effect on the Structural, Electrical, and Optical Properties of In-Line Sputtered Aluminum Doped Zinc Oxide Films Explored with Thermal Desorption Spectroscopy

    Directory of Open Access Journals (Sweden)

    Shang-Chou Chang

    2014-01-01

    Full Text Available This work investigates the thermal effect on the structural, electrical, and optical properties of aluminum doped zinc oxide (AZO films. The AZO films deposited at different temperatures were measured using a thermal desorption system to obtain their corresponding thermal desorption spectroscopy (TDS. In addition to obtaining information of thermal desorption, the measurement of TDS also has the effect of vacuum annealing on the AZO films. The results of measuring TDS imply part of the doped aluminum atoms do not stay at substituted zinc sites in AZO films. The (002 preferential direction of the AZO films in X-ray diffraction spectra shifts to a lower angle after measurement of TDS. The grain size grows and surface becomes denser for all AZO films after measurement of TDS. The carrier concentration, mobility, and average optical transmittance increase while the electrical resistivity decreases for AZO films after measurement of TDS. These results indicate that the AZO films deposited at 200°C are appropriate selections if the AZO films are applied in device fabrication of heat-produced process.

  8. Influence of technology of nanopowder production on the microstructure of the sintered by spark-plasma material on the example of aluminum oxide

    Science.gov (United States)

    Zholnin, A. G.; Melekhov, A. P.; Hafizov, R. S.; Vakulenko, S. A.; Rubinkovskiy, N. A.; Samokhin, A. V.; Alekseev, N. V.; Grigoryev, E. G.

    2016-04-01

    A comparative study of the results of spark-plasma sintering (SPS) of two-types of aluminum oxide nanopowders, obtained by the method of conductor explosion and plasma synthesis. When the parameters of both powders are similar (spherical form of the particles, size, phase composition) as well as SPS modes the properties of the resulting compacts are significantly different both in mechanical properties and microstructure. The reason of differences in the properties of the obtained compacts is in technological impurities in powders, obtained by different methods. Artificial addition of impurities, contained in the nanopowder, obtained by electro explosion of conductor, into the powder, made by synthesis in plasma and not containing these impurities, allowed to reveal their effect on the formation of the microstructure and properties of the sintered by SPS method sample.

  9. Effects of pH, surface finish and thermal treatment on the corrosion of AlFeNi aluminum alloy. Characterization of oxide layers

    Science.gov (United States)

    Nabhan, D.; Kapusta, B.; Billaud, P.; Colas, K.; Hamon, D.; Dacheux, N.

    2015-02-01

    The aluminum alloy AlFeNi used as fuel cladding for the Jules Horowitz Reactor (JHR) may undergo corrosion in the reactor environment. In order to qualify the corrosion behavior of the fuel elements of the JHR in accidental conditions, several specimens of AlFeNi have been corroded at 250 °C for different durations (9-34 days) in distilled water at various pH (4.9, 5.2 and 5.6) chosen to simulate that currently considered for the JHR. On all specimens, the only crystalline corrosion product formed is boehmite (AlOOH). The corrosion film is composed of three oxide layers which show through thickness chemical composition variations. The iron-nickel precipitates pre-existing in the metal matrix are present in the inner and intermediate oxide layers though oxidized. For long corrosion times, some of the iron and nickel particles are released in the water and some precipitation is observed at the surface of the oxide layer. The effect of surface finish (as received or polished) and thermal treatment (annealed and not annealed) on the oxide growth rate has also been investigated. For durations over 25 days, pH = 5.6 appears to be more favorable than pH = 5.2 and 4.9 in terms of oxide thickness and weight gain limitation. This effect of pH is however reduced on unpolished specimens. The effect of surface finish on the corrosion behavior as measured by optical microscopy appears to be strong, especially for pH = 4.9 where polished samples exhibited an accelerated evolution of the oxide thickness and of the mass gain. This could be due to the combined effect of a strong acid solution (pH = 4.9) and of the local microstructural changes formed at the interface through polishing. The effect of thermal treatment on the behavior of unpolished AlFeNi specimens during corrosion tests in the conditions investigated was found to be small. In this study, microstructural and chemical analyses were performed on the corroded specimens in order to get a better understanding of the

  10. Effects of pH, surface finish and thermal treatment on the corrosion of AlFeNi aluminum alloy. Characterization of oxide layers

    Energy Technology Data Exchange (ETDEWEB)

    Nabhan, D., E-mail: diana.nabhan@cea.fr [Département des matériaux pour le nucléaire, CEA Saclay, 91191 Gif sur Yvette (France); Kapusta, B.; Billaud, P.; Colas, K.; Hamon, D. [Département des matériaux pour le nucléaire, CEA Saclay, 91191 Gif sur Yvette (France); Dacheux, N. [ICSM, UMR 5257 CNRS/CEA/UM2/ENSCM, Site de Marcoule, Bât 426, BP 17171, 30207 Bagnols/Cèze (France)

    2015-02-15

    The aluminum alloy AlFeNi used as fuel cladding for the Jules Horowitz Reactor (JHR) may undergo corrosion in the reactor environment. In order to qualify the corrosion behavior of the fuel elements of the JHR in accidental conditions, several specimens of AlFeNi have been corroded at 250 °C for different durations (9–34 days) in distilled water at various pH (4.9, 5.2 and 5.6) chosen to simulate that currently considered for the JHR. On all specimens, the only crystalline corrosion product formed is boehmite (AlOOH). The corrosion film is composed of three oxide layers which show through thickness chemical composition variations. The iron–nickel precipitates pre-existing in the metal matrix are present in the inner and intermediate oxide layers though oxidized. For long corrosion times, some of the iron and nickel particles are released in the water and some precipitation is observed at the surface of the oxide layer. The effect of surface finish (as received or polished) and thermal treatment (annealed and not annealed) on the oxide growth rate has also been investigated. For durations over 25 days, pH = 5.6 appears to be more favorable than pH = 5.2 and 4.9 in terms of oxide thickness and weight gain limitation. This effect of pH is however reduced on unpolished specimens. The effect of surface finish on the corrosion behavior as measured by optical microscopy appears to be strong, especially for pH = 4.9 where polished samples exhibited an accelerated evolution of the oxide thickness and of the mass gain. This could be due to the combined effect of a strong acid solution (pH = 4.9) and of the local microstructural changes formed at the interface through polishing. The effect of thermal treatment on the behavior of unpolished AlFeNi specimens during corrosion tests in the conditions investigated was found to be small. In this study, microstructural and chemical analyses were performed on the corroded specimens in order to get a better understanding of the

  11. Electrical and optical properties of radio frequency magnetron-sputtered lightly aluminum-doped zinc oxide thin films deposited in hydrogen–argon gas

    International Nuclear Information System (INIS)

    We studied the electrical and optical properties of lightly aluminum-doped zinc oxide (L-AZO) films, which were deposited on soda-lime glass substrates by radio frequency (RF) magnetron sputtering using a 0.2 wt.% aluminum-doped zinc oxide target and a 0.3 wt.% hydrogen-mixed argon (Ar/0.3% H2) gas. The L-AZO films were characterized in terms of structural, optical, and electrical properties by X-ray diffraction, ultraviolet–visible spectrophotometry, photoluminescence and Hall measurements at room temperature. The Al contents of the L-AZO film were analyzed with secondary ion mass spectroscopy. As the Ar/0.3%H2 gas flow was increased up to 200 sccm, the transmittance and conductivity of the film simultaneously improved as a function of the increasing flow rate without additional thermal or gas treatment. The 40 nm-thick L-AZO film, which was deposited by an Ar/0.3% H2 gas flow of 200 sccm at a substrate temperature of 100 °C, had a carrier concentration of 1.0 × 1020/cm3, resistivity of 5.5 × 10−3 Ω-cm, and an average transmittance of 93% in the wavelength range from 300 nm to 2000 nm. - Highlights: • Electrical and optical properties of lightly Al-doped ZnO (L-AZO) thin films. • Films studied under various deposition conditions. • Carrier concentration (CC) and transmittance for thickness > 100 nm is studied. • For thin L-AZO films, CC and transmittance depend on O vacancies and interstitial H atoms

  12. Microstructural and mechanical properties of nanometric magnesium oxide particulate-reinforced aluminum matrix composites produced by powder metallurgy method

    International Nuclear Information System (INIS)

    In this research, aluminum alloy (A356.1) matrix composites reinforced with 1.5, 2.5 and 5 Vol.% nanoscale MgO particles were fabricated via powder metallurgy method. Pure atomized aluminum powder with an average particle size of 1μm and MgO particulate with an average particle size between 60 to 80 nm were used. The specimens were pressed by Cold Isostatic Press machine (CIP), and were subsequently sintered at various sintering temperatures, viz. 575, 600 and 625 .deg. C. Optimum amount of reinforcement and sintering temperature were determined by evaluating the density, microstructure and mechanical properties of composites. The composites were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). Hardness and compression tests were carried out in order to identify mechanical properties. Reinforcing the Al matrix alloy with MgO particles improved the hardness and compressive strength of the alloy to a maximum value of 44 BHN and 288 MPa, respectively. The most improved compressive strength was obtained with the specimen including 2.5% of MgO sintered at 625 .deg. C. According to the experiments, a sintering temperature of 625 .deg. C showed better results than other temperatures. A good distribution of the dispersed MgO particulates in the matrix alloy was achieved

  13. Preparation technology and anti-corrosion performances of black ceramic coatings formed by micro-arc oxidation on aluminum alloys

    Institute of Scientific and Technical Information of China (English)

    CHEN Ling; HAN Jing; YU Shengxue

    2006-01-01

    In order to prepare ornamental and anti-corrosive coating on aluminum alloys, preparation technology of black micro-arc ceramic coatings on Al alloys in silicate based electrolyte was studied.The influence of content of Na2WO4 and combination additive in solution on the performance of black ceramic coatings was studied; the anticorrosion performances of black ceramic coatings were evaluated through whole-immersion test and electrochemical method in 3.5% NaCl solution at different pH value; SEM and XRD were used to analyze the surface morphology and phase constitutes of the black ceramic coatings.Experimental results indicated that, without combination additives, with the increasing of Na2WO4 content in the electrolyte, ceramic coating became darker and thicker, but the color was not black; after adding combination additive, the coating turned to be black; the black ceramic coating was multi-hole form in surface.There was a small quantity of tungsten existing in the black ceramic coating beside α-Al2O3 phase and β-Al2O3 phase.And aluminum alloy with black ceramic coating exhibited excellent anti-corrosion property in acid, basic and neutral 3.5% NaCl solution.

  14. 微波消解-火焰原子吸收光谱法测定氧化铝中的氧化钠%Determination of Sodium Oxide in Aluminum Oxide by Microwave Digestion-flame Atomic Absorption Spectrometry

    Institute of Scientific and Technical Information of China (English)

    薛心禄

    2012-01-01

    氧化铝中氧化钠含量的测定,一般采用高温熔结,用水浸出钠盐后,用原予吸收火焰光度法测定,该方法的测定周期比较长,而且高温熔结时对铂金皿的损耗比较大。文章提出了试样用磷酸和硫酸混合溶液,在高压微波消解器中进行处理,将样品在较短的时间内消解,并在试液中加入一定量的氯化铯,消除钠的电离干扰,采用原子吸收光谱法直接测定,测试结果与标准样品推荐值比较,结果令人满意。%The sodium oxide content in aluminum oxide is usually determined by atomic absorption spectrophotometry with high temperature melting and leaching, which is time consuming and damage platinum bowl. The paper proposed forward to determine with sample of mixed phosphoric acid and sulfuric acid solution to process in the high pressure microwave digestion device. The samples were digested in a relatively short time, and added a certain amount of cesium chloride in the test solution. Used for eliminate ionization interference of sodium to directly determine sodium oxide in aluminum oxide by Atomic Absorption Spectrophotometer. Under the comparison of test results and recommended values of standard samples, it was satisfactory.

  15. Effects of electrical discharge surface modification of superalloy Haynes 230 with aluminum and molybdenum on oxidation behavior

    International Nuclear Information System (INIS)

    The effects of the electrical discharge alloying (EDA) process on improving the high temperature oxidation resistance of the Ni-based superalloy Haynes 230 have been investigated. The 85 at.% Al and 15 at.% Mo composite electrode provided the surface alloying materials. An Al-rich layer is produced on the surface of the EDA specimen alloyed with positive electrode polarity, whereas, many discontinuous piled layers are attached to the surface of the EDA superalloy when negative electrode polarity is selected. The oxidation resistance of the specimen alloyed with positive electrode polarity is better than that of the unalloyed superalloy, and the effective temperature of oxidation resistance of the alloyed layer can be achieved to 1100 oC. Conversely, the oxidation resistance of the other EDA specimen alloyed with negative electrode polarity is even worse than that of the unalloyed superalloy

  16. Ultra-trace determination of arsenic species in environmental waters, food and biological samples using a modified aluminum oxide nanoparticle sorbent and AAS detection after multivariate optimization

    International Nuclear Information System (INIS)

    We describe a simple and efficient method for solid phase extraction and speciation of trace quantities of arsenic. It is based on the use of functionalized aluminum oxide nanoparticles and does not require any oxidation or reduction steps. The experimental parameters affecting extraction and quantitation were optimized using fractional factorial design methods. Adsorbed arsenic was eluted from the sorbent with 1 M hydrochloric acid and determined by graphite furnace atomic absorption spectrometry. Preconcentration factors up to 750 were achieved depending on the sample volume. Studies on potential interferences by various anions and cations showed the method to be highly selective. Under optimum conditions, the calibration plots are linear in the 5.0 to 280 ng L−1 and 8.0 to 260 ng L−1 concentration ranges for As(III) and total arsenic, respectively. The detection limits (calculated for S/N ratios of 3) are 1.81 and 1.97 ng L−1 for As(III) and total arsenic, respectively. The method was successfully applied to the determination and speciation of arsenic in (spiked) environmental, food and biological samples and gave good recoveries. The method was validated using a certified geological reference material. (author)

  17. Corrosion barriers for silver-based telescope mirrors: comparative study of plasma-enhanced atomic layer deposition and reactive evaporation of aluminum oxide

    Science.gov (United States)

    Fryauf, David M.; Phillips, Andrew C.; Kobayashi, Nobuhiko P.

    2015-10-01

    Astronomical telescopes continue to demand high-endurance high-reflectivity silver (Ag) mirrors that can withstand years of exposure in Earth-based observatory environments. We present promising results of improved Ag mirror robustness using plasma-enhanced atomic layer deposition (PEALD) of aluminum oxide (AlOx) as a top barrier layer. Transparent AlOx is suitable for many optical applications; therefore, it has been the initial material of choice for this study. Two coating recipes developed with electron beam ion-assisted deposition (e-beam IAD) of materials including yttrium fluoride, titanium nitride, oxides of yttrium, tantalum, and silicon are used to provide variations in basic Ag mirror structures to compare the endurance of reactive e-beam IAD barriers with PEALD barriers. Samples undergo high temperature/high humidity environmental testing in a controlled environment of 80% humidity at 80°C for 10 days. Environmental testing shows visible results suggesting that the PEALD AlOx barrier offers robust protection against chemical corrosion and moisture permeation. Ag mirror structures were further characterized by reflectivity/absorption before and after deposition of AlOx barriers.

  18. Influence of anodization parameters on the volume expansion of anodic aluminum oxide formed in mixed solution of phosphoric and oxalic acids

    Science.gov (United States)

    Kao, Tzung-Ta; Chang, Yao-Chung

    2014-01-01

    The growth of anodic alumina oxide was conducted in the mixed solution of phosphoric and oxalic acids. The influence of anodizing voltage, electrolyte temperature, and concentration of phosphoric and oxalic acids on the volume expansion of anodic aluminum oxide has been investigated. Either anodizing parameter is chosen to its full extent of range that allows the anodization process to be conducted without electric breakdown and to explore the highest possible volume expansion factor. The volume expansion factors were found to vary between 1.25 and 1.9 depending on the anodizing parameters. The variation is explained in connection with electric field, ion transport number, temperature effect, concentration, and activity of acids. The formation of anodic porous alumina at anodizing voltage 160 V in 1.1 M phosphoric acid mixed with 0.14 M oxalic acid at 2 °C showed the peak volume expansion factor of 1.9 and the corresponding moderate growth rate of 168 nm/min.

  19. Influence of growth temperature on electrical, optical, and plasmonic properties of aluminum:zinc oxide films grown by radio frequency magnetron sputtering

    Science.gov (United States)

    Dondapati, Hareesh; Santiago, Kevin; Pradhan, A. K.

    2013-10-01

    We have investigated the responsible mechanism for the observation of metallic conductivity at room temperature and metal-semiconductor transition (MST) at lower temperatures for aluminum-doped zinc oxide (AZO) films. AZO films were grown on glass substrates by radio-frequency magnetron sputtering with varying substrate temperatures (Ts). The films were found to be crystalline with the electrical resistivity close to 1.1 × 10-3 Ω cm and transmittance more than 85% in the visible region. The saturated optical band gap of 3.76 eV was observed for the sample grown at Ts of 400 °C, however, a slight decrease in the bandgap was noticed above 400 °C, which can be explained by Burstein-Moss effect. Temperature dependent resistivity measurements of these highly conducting and transparent films showed a MST at ˜110 K. The observed metal-like and metal-semiconductor transitions are explained by taking into account the Mott phase transition and localization effects due to defects. All AZO films demonstrate crossover in permittivity from positive to negative and low loss in the near-infrared region, illustrating its applications for plasmonic metamaterials, including waveguides for near infrared telecommunication region. Based on the results presented in this study, the low electrical resistivity and high optical transmittance of AZO films suggested a possibility for the application in the flexible electronic devices, such as transparent conducting oxide film on LEDs, solar cells, and touch panels.

  20. Preparation of well-aligned carbon nanotubes/silicon nanowires core-sheath composite structure arrays in porous anodic aluminum oxide templates

    Institute of Scientific and Technical Information of China (English)

    李梦轲; 陆梅; 王成伟; 力虎林

    2002-01-01

    The well-aligned carbon nanotubes (CNTs) arrays with opened ends were prepared in ordered pores of anodic aluminum oxide (AAO) template by the chemical vapor deposition (CVD) method. After then, silicon nanowires (SiNWs) were deposited in the hollow cavities of CNTs. By using this method, CNTs/SiNWs core-sheath composite structure arrays were synthesized successfully. Growing structures and physical properties of the CNTs/SiNWs composite structure arrays were analyzed and researched by the scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction spectrum (XRD), respectively. The field emission (FE) behavior of the CNTs/SiNWs composite structure arrays was studied based on Fowler- Nordheim tunneling mechanism and current-voltage (I -V) curve. And the photoluminescence (PL) was also characterized. Significantly, the CNTs/SiNWs core-sheath composite structure nanowire fabricated by AAO template method is characteristic of a metal/semiconductor (M/S) behavior and can be utilized to synthesize nanoscale PN junction or Schottky diode device. This process also could be useful for the fabrication of SiNWs and other nanoscale core-sheath composite structure nanowires with chemically inert interfaces for nanoscale electronic and device applications where surface oxidation is undesirable. The diameters and lengths of nanoscale composite structure arrays can be dominated easily, and the experimental result shows that the curling and twisting structures are fewer than those prepared by other synthesized methods.

  1. Effect of sandblasting with different size of aluminum oxide particles on tensile bond strength of resilient liner to denture base

    Directory of Open Access Journals (Sweden)

    Ali K Ozdemir

    2011-01-01

    ="false" Priority="21" SemiHidden="false" UnhideWhenUsed="false" QFormat="true" Name="Intense Emphasis" />

    Objectives: The purpose of this study was to investigate the bonding properties of sandblasted with different size of aluminum oxide particles denture base to silicone based soft denture liner.

    Co-Mn-Al Mixed Oxides on Anodized Aluminum Supports and Their Use as Catalysts in the Total Oxidation of Ethanol

    Czech Academy of Sciences Publication Activity Database

    Kovanda, F.; Jirátová, Květa; Ludvíková, Jana; Raabová, H.

    2013-01-01

    Roč. 464, AUG 15 (2013), s. 181-190. ISSN 0926-860X R&D Projects: GA ČR GAP106/10/1762 Institutional support: RVO:67985858 Keywords : layered double hydroxides * hydrothermal reaction * mixed oxides * supported catalysts * ethanol total oxidation Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 3.674, year: 2013

  2. Solubility and hydrolysis of aluminum oxides and hydroxides at elevated temperatures from apparent molar heat capacity and volume measurements near 25 degree C

    International Nuclear Information System (INIS)

    Most metal oxides are so insoluble under neutral or basic conditions that direct solubility measurements over wide ranges of pH and temperature are very difficult. Extrapolations of room temperature data to elevated temperatures and pressures require standard partial molar heat capacity and volume functions for the aqueous metal species and all of its hydroxy complexes. Aluminum is one of the few metals whose solubility in alkaline solutions is high enough to permit the heat capacity function of one of the anionic hydroxy complexes, Al(OH)4-(aq), to be measured directly by calorimetry. This paper summarizes recent measurements leading to the apparent molar heat capacities and volumes of AlCl3(aq), Al(NO3)3(aq) and NaAl(OH)4(aq) which have led to standard partial molar heat capacity and volume functions for Al+3(aq) and Al(OH)4-(aq), from 10 to 55 degree C. The results at 25 degree C differ from the Criss-Cobble Entropy Correspondence predictions by more than 130 J K-1 mol-1. Because Al3+(aq) and Al(OH)4-(aq) are the end members of the hydrolysis sequence for aluminum, the thermodynamic functions for the intermediate species can be estimated by interpolation. We have used the Helgeson-Kirkham-Flowers model to extrapolate the experimental heat capacity and volume functions of both end member ions upward in temperature to 300 degree C. Values for the intermediate species, AI(OH)m3-m, were estimated by linear interpolation of the non-Born terms in the model. The Gibbs energies of formation calculated from this approach lead to solubility products for boehmite which agree with experimental results up to 250 degree C over the entire pH range

  3. Improving the direct electron transfer in monolithic bioelectrodes prepared by immobilization of FDH enzyme on carbon-coated anodic aluminum oxide films

    Directory of Open Access Journals (Sweden)

    Alberto eCastro-Muñiz

    2016-02-01

    Full Text Available The present work reports the preparation of binderless carbon-coated porous films and the study of their performance as monolithic bioanodes. The films were prepared by coating anodic aluminum oxide (AAO films with a thin layer of nitrogen-doped carbon by chemical vapor deposition. The films have cylindrical straight pores with controllable diameter and length. These monolithic films were used directly as bioelectrodes by loading the films with D-fructose dehydrogenase (FDH, an oxidoreductase enzyme that catalyzes the oxidation of D-fructose to 5-keto-D-fructose. The immobilization of the enzymes was carried out by physical adsorption in liquid phase and with an electrostatic attraction method. The latter method takes advantage of the fact that FDH is negatively charged during the catalytic oxidation of fructose. Thus the immobilization was performed under the application of a positive voltage to the CAAO film in a FDH-fructose solution in McIlvaine buffer (pH 5 at 25 ºC. As a result, the FDH modified electrodes with the latter method show much better electrochemical response than that with the conventional physical adsorption method. Due to the singular porous structure of the monolithic films, which consists of an array of straight and parallel nanochannels, it is possible to rule out the effect of the diffusion of the D-fructose into the pores. Thus the improvement in the performance upon using the electrostatic attraction method can be ascribed not only to a higher uptake, but also to a more appropriate molecule orientation of the enzyme units on the surface of the electrodes.

  4. Improving the direct electron transfer in monolithic bioelectrodes prepared by immobilization of FDH enzyme on carbon-coated anodic aluminum oxide films

    Science.gov (United States)

    Castro-Muñiz, Alberto; Hoshikawa, Yasuto; Komiyama, Hiroshi; Nakayama, Wataru; Itoh, Tetsuji; Kyotani, Takashi

    2016-02-01

    The present work reports the preparation of binderless carbon-coated porous films and the study of their performance as monolithic bioanodes. The films were prepared by coating anodic aluminum oxide (AAO) films with a thin layer of nitrogen-doped carbon by chemical vapor deposition. The films have cylindrical straight pores with controllable diameter and length. These monolithic films were used directly as bioelectrodes by loading the films with D-fructose dehydrogenase (FDH), an oxidoreductase enzyme that catalyzes the oxidation of D-fructose to 5-keto-D-fructose. The immobilization of the enzymes was carried out by physical adsorption in liquid phase and with an electrostatic attraction method. The latter method takes advantage of the fact that FDH is negatively charged during the catalytic oxidation of fructose. Thus the immobilization was performed under the application of a positive voltage to the CAAO film in a FDH-fructose solution in McIlvaine buffer (pH 5) at 25 ºC. As a result, the FDH modified electrodes with the latter method show much better electrochemical response than that with the conventional physical adsorption method. Due to the singular porous structure of the monolithic films, which consists of an array of straight and parallel nanochannels, it is possible to rule out the effect of the diffusion of the D-fructose into the pores. Thus the improvement in the performance upon using the electrostatic attraction method can be ascribed not only to a higher uptake, but also to a more appropriate molecule orientation of the enzyme units on the surface of the electrodes.

  5. TEM analysis and wear resistance of the ceramic coatings on Q235 steel prepared by hybrid method of hot-dipping aluminum and plasma electrolytic oxidation

    International Nuclear Information System (INIS)

    Highlights: ► Transmission electron microscopy (TEM) was firstly used to analyze the phase composition of the ceramic coatings. ► The phase composition of the ceramic coatings is mainly amorphous phase and crystal Al2O3 oxides. ► The cross-section micro-hardness of the treated samples was investigated, the hardness of the ceramic coatings is about HV1300. ► The wear resistance of the PEO samples is about 3 times higher than that of the heat treated 45 steel. - Abstract: The hybrid method of PEO and hot-dipping aluminum (HDA) was employed to deposit composite ceramic coatings on the surface of Q235 steel. The composition of the composite coatings was investigated with X-ray diffraction (XRD) and transmission electron microscopy (TEM), respectively. The cross-section microstructure and micro-hardness of the treated specimens were investigated and analyzed with scanning electron microscopy (SEM) and microscopic hardness meter (MHM), respectively. The wear resistance of the ceramic coatings was investigated by a self-made rubbing wear testing machine. The results indicate that metallurgical bonding can be observed between the ceramic coatings and the steel substrate. There are many micro-pores and micro-cracks, which act as the discharge channels and result of quick and non-uniform cooling of melted sections in the plasma electrolytic oxidation ceramic coatings. The phase composition of the ceramic coatings is mainly composed of amorphous phase and crystal Al2O3 oxides. The crystal Al2O3 phase includes κ-Al2O3, θ-Al2O3 and β-Al2O3. The grain size of the κ-Al2O3 crystal is quite non-uniform. The hardness of the ceramic coatings is about HV1300 and 10 times higher than that of the Q235 substrate, which was favorable to the better wear resistance of the ceramic coatings.

  6. Oxide-cladding aluminum nitride photonic crystal slab: Design and investigation of material dispersion and fabrication induced disorder

    International Nuclear Information System (INIS)

    Photonic crystal slabs with a lower-index material surrounding the core layer are an attractive choice to circumvent the drawbacks in the fabrication of membranes suspended in air. In this work we propose a photonic crystal (PhC) slab structure composed of a triangular pattern of air holes in a multilayer thin film of aluminum nitride embedded in silicon dioxide layers designed for operating around 450 nm wavelengths. We show the design of an ideal structure and analyze the effects of material dispersion based on a first-order correction perturbation theory approach using dielectric functions obtained by experimental measurements of the thin film materials. Numerical methods were used to investigate the effects of fabrication induced disorder of typical nanofabrication processes on the bandgap size and spectral response of the proposed device. Deviation in holes radii and positions were introduced in the proposed PhC slab model with a Gaussian distribution profile. Impacts of slope in holes sidewalls that might result from the dry etching of AlN were also evaluated. The results show that for operation at the midgap frequency, slope in holes sidewalls is more critical than displacements in holes sizes and positions

  7. Oxide-cladding aluminum nitride photonic crystal slab: Design and investigation of material dispersion and fabrication induced disorder

    Energy Technology Data Exchange (ETDEWEB)

    Melo, E. G., E-mail: emerdemelo@usp.br; Alvarado, M. A.; Carreño, M. N. P.; Alayo, M. I. [Electronic Systems Engineering Department, University of São Paulo, CEP 05508-010 São Paulo, SP (Brazil); Carvalho, D. O. [UNESP - São Paulo State University, CEP 13874-149 São João da Boa Vista, SP (Brazil); Ferlauto, A. S. [Department of Physics, Federal University of Minas Gerais, CEP 31270-901 Belo Horizonte, MG (Brazil)

    2016-01-14

    Photonic crystal slabs with a lower-index material surrounding the core layer are an attractive choice to circumvent the drawbacks in the fabrication of membranes suspended in air. In this work we propose a photonic crystal (PhC) slab structure composed of a triangular pattern of air holes in a multilayer thin film of aluminum nitride embedded in silicon dioxide layers designed for operating around 450 nm wavelengths. We show the design of an ideal structure and analyze the effects of material dispersion based on a first-order correction perturbation theory approach using dielectric functions obtained by experimental measurements of the thin film materials. Numerical methods were used to investigate the effects of fabrication induced disorder of typical nanofabrication processes on the bandgap size and spectral response of the proposed device. Deviation in holes radii and positions were introduced in the proposed PhC slab model with a Gaussian distribution profile. Impacts of slope in holes sidewalls that might result from the dry etching of AlN were also evaluated. The results show that for operation at the midgap frequency, slope in holes sidewalls is more critical than displacements in holes sizes and positions.

  8. Synthesis and characterization of aluminum and Al/REE pillared clays and supported palladium catalysts for benzene oxidation

    Institute of Scientific and Technical Information of China (English)

    ZUO Shufeng; ZHOU Renxian; QI Chenze

    2011-01-01

    Volatile organic compounds (VOCs) are considered as a major pollutant in indoor and outdoor air. More stringent environmental regulations have been implemented in order to reduce the VOC emissions. One of the techniques available for destructive removal of VOCs is catalytic oxidation. In the present work, Al/Rare Earths (REE: Y, Ce, La, Pr and Nd) pillared clays (PILCs) were used to support 0.2 wt.% of palladium for the complete oxidation of low concentration of benzene. The supports and catalysts were characterized by XRD, N2 adsorption/desorption, FTIR spectroscopy, HRTEM and H2-TPR techniques. The results indicated that after Al and Al/REE pillaring, the basal spacing, SBET, Amic and Vmic of Al and AlREE-PILC had a considerable increase compared with those of Na-mmt. Activity tests of deep oxidation of benzene showed that the catalytic activity of Pd catalysts supported on Al and AlREE-PILC were much higher than that on initial clays,which was due to the fact that optimized structure of PILCs, such as large basal spacing, high SBET and porosity, improved Pd dispersion and increased the active sites of Pd. Especially for Pd/AlCe-PILC, the temperature of complete oxidation was about 280 C, exhibiting the highest catalytic activity.

  9. NEW SYNTHETIC METHOD AND CHARACTERIZATION OF CERAMIC FILMS PREPARED BY ANODIC OXIDATION OF ALUMINUM UNDER SPARKING DISCHARGE

    OpenAIRE

    Yamada, M.; Mita, I.

    1986-01-01

    A new synthetic method of ceramic films by anodic oxidation of aluminium was developed. Most of the crystals in the films are composed of eta or alpha-alumina. These ceramic films can incorporate a lot of metals by electrolytic methods.

  10. Luminescence of the B{sup 2}{Sigma}{sup +}-X{sup 2}{Sigma}{sup +} band system of AlO during plasma electrolytic oxidation of aluminum

    Energy Technology Data Exchange (ETDEWEB)

    Stojadinovic, S., E-mail: sstevan@ff.bg.ac.rs [Faculty of Physics, University of Belgrade, Studentski trg 12-16, 11000 Belgrade (Serbia); Peric, M. [Faculty of Physical Chemistry, University of Belgrade, Studentski trg 12-16, 11000 Belgrade (Serbia); Petkovic, M. [Faculty of Physics, University of Belgrade, Studentski trg 12-16, 11000 Belgrade (Serbia); Vasilic, R. [Faculty of Environmental Governance and Corporate Responsibility, Educons University, Vojvode Putnika bb, Sremska Kamenica (Serbia); Kasalica, B.; Belca, I. [Faculty of Physics, University of Belgrade, Studentski trg 12-16, 11000 Belgrade (Serbia); Radic-Peric, J. [Faculty of Physical Chemistry, University of Belgrade, Studentski trg 12-16, 11000 Belgrade (Serbia)

    2011-11-30

    Highlights: > Plasma electrolytic oxidation (PEO) of aluminum in citric acid. > Luminescence of the B{sup 2}{Sigma}{sup +}-X{sup 2}{Sigma}{sup +} band system of AlO during PEO. > The measured intensity distributions are employed to estimate the mean plasma temperature. > The composition of plasma containing aluminum and oxygen is calculated. - Abstract: Two broad luminescence peaks with clearly pronounced structure, extending from roughly 18,200 to 18,800 cm{sup -1} and from 19,000 to 19,700 cm{sup -1} with the maxima at approximately 18,500 and 19,500 cm{sup -1}, respectively, are obtained during plasma electrolytic oxidation of aluminum. They are assigned to the v'-v'' = -1 and -2 band sequences of the B{sup 2}{Sigma}{sup +}-X{sup 2}{Sigma}{sup +} emission transition of AlO. The measured intensity distributions are employed to estimate the population of vibrational levels of the upper electronic state, and consequently the mean plasma temperature. The composition of plasma containing aluminum and oxygen under assumption of thermodynamic equilibrium is calculated in the temperature up to 11,000 K in order to explain the appearance of the observed spectral features.

  11. 铝合金阳极氧化无镍封孔工艺研究%The study of Aluminum alloy anodic oxidation and nickel hole sealing process

    Institute of Scientific and Technical Information of China (English)

    刘岩; 刘桂宏; 朱鸿昌; 张万龙; 高敏亮; 王亮; 王梅丰

    2015-01-01

    铝阳极氧化膜在不同封孔溶液中封闭后,其使用寿命和耐蚀性会各不相同。采用了磷铬酸失重法、电化学极化曲线法、交流阻抗法研究了铝合金阳极氧化膜在氟锆酸钾、HX-588封闭剂、钼酸钠、亚硝酸钠和纯水的高温水溶液封闭后的耐蚀性,比较其间的差异,并找出其变化规律,反映出五种溶液的封闭效果。数据表明:封闭效果优劣排序依次为HX-588封闭剂、氟锆酸钾、钼酸钠、亚硝酸钠、纯水。说明氟锆酸钾可以作为一种绿色无镍封孔剂进行工业生产。%The service life and corrosion resistance of sealed Aluminum anodic oxide film in different hole sealing solution will be different. The corrosion resistance of the sealed Aluminum oxide film in Zirconium fluoride acid potassium,HX-588 sealing agent,sodium molybdate,sodium nitrite and pure water of high temperature solution were studied by phosphorus-chromium acid weight-loss method and electrochemical polarization-curve method,electrochemical impedance spectros-copy,compare their differences and find out its change rule,reflects the sealing effect of 5 kinds of solution. The statistic shows that the sequence of sealing effect from excellent is HX-588 sealants,zirconium fluoride acid potassium,sodium mo-lybdate,sodium nitrite,pure water. That zirconium fluoride potassium can serve as a kind of green and nickel hole sealing a-gent for industrial production.

  12. Preparation of mesoporous alumina films by anodization: Effect of pretreatments on the aluminum surface and MTBE catalytic oxidation

    International Nuclear Information System (INIS)

    Mesoporous materials are both scientifically and technologically important because of the presence of voids of controllable dimensions at atomic, molecular, and nanometric scales. Over the last decade, there has been both an increasing interest and research effort in the synthesis and characterization of these types of materials. The purposes of this work are to study the physical and chemical changes in the properties of mesoporous alumina films produced by anodization in sulphuric acid by different pretreatments on the aluminium surface such as mechanical polishing [MP] and electropolishing [EP]; and to compare their properties such as morphology, structure and catalytic activity with those present in commercial alumina. The morphologic and physical characterizations of the alumina film samples were carried out by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The chemical evaluations were performed by the oxidation of methyl-tert-butyl-ether (MTBE) at 400 deg. C under O2/He oxidizing conditions (Praxair, 2.0% O2/He balance). According to the results, the samples that presented higher activities than those in Al2O3/Al [MP] and commercial alumina in the MTBE oxidation (69%), were those prepared by Al2O3/Al [EP]. The average mesoporous diameter was 17 nm, and the morphological shape was equiaxial; thus, that pore distribution was the smallest of all with a homogeneous distribution.

  13. Properties of alumina coating formed by microarc oxidation technique on 6061 aluminum alloy; Eigenschaften von mittels Microarc-Oxidations-Verfahren erzeugten Aluminiumbeschichtungen auf der Aluminiumlegierung 6061

    Energy Technology Data Exchange (ETDEWEB)

    Polat, Aytekin; Usta, Metin [Gebze Institute of Technology, Kocaeli (Turkey). Dept. of Materials Science and Engineering; Makaraci, Murat [Kocaeli Univ. (Turkey). Dept. of Mechanical Engineering; Tas, Zakir [Bozok Univ., Yozgat (Turkey); Ata, Ali

    2008-12-15

    In this study, thick and hard alumina coatings were produced on 6061-T6 Al alloy substrates for different oxidation times and current densities by using of microarc oxidation (MAO) technique in an alkali-silicate electrolytic solution. The influence of oxidation time and current density on the kinetics, phase composition, hardness, surface roughness and structure of the coating were investigated. It is found that the kinetics of coating mainly depends on applied current density and oxidation time. The XRD results revealed that the coatings are composed of mainly {alpha}-Al{sub 2}O{sub 3}, {gamma}-Al{sub 2}O{sub 3} and mullite phase. The relative ratio of harder and denser {alpha}-Al{sub 2}O{sub 3} phase increases with increasing current density and oxidation time. For the same coating time, the position of maximum hardness of coatings moves away from the substrate-coating interface to the coating surface with increasing current density. The surface roughness of coating is a function of coating thickness and increases with increasing deposition time and current density. The surface micro hardness of Al 6061-T6 alloy substrate was increased up to 2200 HV hardness after the coating. (orig.)

  14. Influence of composition and processing parameters on the properties of solution-processed aluminum phosphate oxide (AlPO) thin films

    Science.gov (United States)

    Norelli, Kevin M.; Plassmeyer, Paul N.; Woods, Keenan N.; Glassy, Benjamin A.; Knutson, Christopher C.; Beekman, Matt; Page, Catherine J.

    2016-05-01

    The effects of precursor solution concentration, composition, and spin-processing parameters on the thickness and electrical properties of ultra-smooth aluminum oxide phosphate (Al2O3-3x(PO4)2x or "AlPO") thin films prepared using aqueous solutions are reported. Compositions were verified by electron probe micro-analysis and range from Al2O1.5(PO4) to AlPO4 (x = P:Al from 0.5 to 1.0). Film thicknesses were determined using X-ray reflectivity measurements and were found to depend systematically on solution concentration, P:Al ratio, and spin-speed. Metal-insulator-semiconductor devices were fabricated to determine electrical properties as a function of composition. As the P:Al ratio increased from 0.5 to 1.0, the dielectric constant decreased from 6.0 to 4.6, leakage currents increased from 0.45 to 65 nA cm-2 at 1 MV cm-1 and dielectric breakdown (defined as leakage currents >10 μA cm-2) decreased from 9.74 to 2.84 MV cm-1. These results establish composition, concentration, and spin-speed for the production of AlPO films with targeted thicknesses and electrical properties.

  15. Optimization of aluminum-doped zinc oxide films deposited at low temperature by radio-frequency sputtering on flexible substrates for solar cell applications

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez, S. [Departamento de Energias Renovables, Energia Solar Fotovoltaica, Centro de Investigaciones Energeticas, Medioambientales y Tecnologicas (CIEMAT), Avda. Complutense 22, 28040 Madrid (Spain); Naranjo, F.B. [Grupo de Ingenieria Fotonica (GRIFO), Departamento de Electronica, Escuela Politecnica Superior, Universidad de Alcala, Campus Universitario, 28871 Alcala de Henares, Madrid (Spain)

    2010-02-15

    Aluminum-doped zinc oxide films were deposited at 100 C on polyethylene terephthalate by radio-frequency magnetron sputtering. The sputtering parameters such as RF power and Argon working pressure were varied from 25 to 125 W and from 1.1 to 0.2 Pa, respectively. The structural properties of as-deposited films were analysed by X-ray diffraction, showing that all the deposited films were polycrystalline, with hexagonal structure and a strong preferred c-axis orientation (0 0 2). Full width at half maximum and grain sizes were around 0.27 and ranged from 24 to 32 nm, respectively. The strain state of the samples was also estimated from X-ray diffraction measurements, obtaining compressive stresses from 0.29 to 0.05 GPa. Resistivity as low as 1.1 x 10{sup -3} {omega} cm was achieved for the film deposited at 75 W and 0.2 Pa, sample that showed a low strain state of -0.06 GPa. High optical transmittance ({proportional_to}80%) was exhibited when films were deposited at RF powers below 100 W. Band gap energies ranged from 3.36 to 3.39 eV and a refractive index of 1.80{+-}0.05, constant in the visible region, was also obtained. (author)

  16. Effects of target angle on the properties of aluminum doped zinc oxide films prepared by DC magnetron sputtering for thin film solar cell applications.

    Science.gov (United States)

    Park, Hyeongsik; Iftiquar, S M; Thuy, Trinh Than; Jang, Juyeon; Ahn, Shihyun; Kim, Sunbo; Lee, Jaehyeong; Jung, Junhee; Shin, Chonghoon; Kim, Minbum; Yi, Junsin

    2014-10-01

    An aluminum doped zinc oxide (AZO) films for front contacts of thin film solar cells, in this work, were prepared by DC magnetron sputtering with different target angles. Effects of target angles on the structural and electro-optical properties of AZO films were investigated. Also, to clarify the light trapping of textured AZO film, amorphous silicon thin film solar cells were fabricated on the textured AZO/glass substrate and the performance of solar cells were studied. The surface became more irregular with increasing the target angle due to larger grains. The self-surface textured morphology, which is a favorable property as front layer of solar cell, exhibited at target angle of 72.5 degrees. We obtained the films with various opto-electronic properties by controlling target angle from 32.5 degrees to 72.5 degrees. The spectral haze increased substantially with the target angle, whereas the electrical resistivity was increased. The conversion efficiency of amorphous silicon solar cells with textured AZO film as a front electrode was improved by the increase of short-circuit current density and fill factor, compared to cell with relatively flat AZO films. PMID:25942853

  17. Pre-treatments applied to oxidized aluminum surfaces to modify the interfacial bonding with bis-1,2-(triethoxysilyl)ethane (BTSE)

    International Nuclear Information System (INIS)

    The methods of X-ray photoelectron spectroscopy (XPS), secondary-ion mass spectrometry (SIMS), and scanning electron microscopy (SEM) have been used to investigate aspects of the bonding of bis-1,2-(triethoxysilyl)ethane (BTSE) onto anodized samples of 7075-T6 aluminum alloy that have been subjected to the various pre-treatments considered in Part I. The oxide layer thins when this sample is subjected to a Forest Products Laboratory (FPL) treatment; topographical changes are detected by SEM after only 5 min, and the 'scallop structures' increase in size for longer times of the FPL treatment. These 7075-Al surfaces adsorb more BTSE than the high-purity Al samples considered in Part I, although the interfacial bonding indicated by the [AlOSi]+/[Al2O]+ SIMS ratios measured for the former samples are constant for different times of FPL treatment, unlike the situation for high-purity Al. Heating anodized 7075-Al samples, either before or after FPL treatment, has no significant effect on the subsequent BTSE adsorption, but a H2 plasma treatment can enhance the interfacial Al-O-Si bonding with a decrease in the total BTSE polymerization

  18. An investigation into the mechanical and tribological properties of plasma electrolytic oxidation and hard-anodized coatings on 6082 aluminum alloy

    International Nuclear Information System (INIS)

    Highlights: → Mechanical properties of PEO and anodised coatings were studied using ultra-micro hardness tester. → Elastic modulus and hardness of the PEO coating were found much higher than those of the anodised coating. → Improved sliding wear of PEO coating is due to presence of hard α and γ-Al2O3 phases. - Abstract: A ceramic coating on AA6082 aluminum alloy prepared by plasma electrolytic oxidation (PEO) has been studied and compared against a sulphuric acid hard-anodized coating on the same alloy. Surface morphology and microstructures of the coatings have been examined by scanning electron microscopy. X-ray diffraction is used to determine the phase composition of the coatings. The adhesion strength of the coatings has been evaluated using a scratch test method. The coating's mechanical properties such elastic modulus and hardness data have been generated using a dynamic ultra-microhardness tester. Sliding wear tests with different loading rates are performed on the coatings in order to assess their wear resistance. Test results show that the PEO treated samples exhibit significantly better mechanical properties compared to hard anodized samples. The elastic modulus and hardness of the PEO coating are 2-3 times greater than of the hard anodized coating and subsequently, an improved wear resistance of the PEO coating has been achieved. The mechanical properties of the coatings and their relations to their tribological performance are discussed.

  19. Reduction of interpore distance of anodized aluminum oxide nano pattern by mixed H3PO4:H2SO4 electrolyte.

    Science.gov (United States)

    Song, Kwang Min; Park, Joonmo; Ryu, Sang-Wan

    2007-11-01

    A self-formed and ordered anodized aluminum oxide (AAO) nano pattern has generated considerable interest in both scientific research and commercial application. However, the interpore distance obtainable by AAO is limited by 40-500 nm depending on electrolyte and anodizing voltage. It's believed that below-30 nm AAO pattern is a key technology in the fabrication semiconductor nano structures with enhanced quantum confinement effect, so we worked on the reduction of interpore distance of AAO with a novel electrolyte. AAO nano patterns were fabricated with mixed H2SO4 and H3PO4 as an electrolyte for various voltages and temperatures. The interpore distance and pore diameter of AAO were decreased with reduced anodizing voltage. As a result, an AAO nano pattern with the interpore distance of 27 nm and the pore diameter of 7 nm was obtained. This is the smallest pattern, as long as we know, reported till now with AAO technique. The fabricated AAO pattern could be utilized for uniform and high density quantum dots with increased quantum effect. PMID:18047152

  1. Characteristics of low-resistivity aluminum-doped zinc oxide films deposited at room temperature by off-axis radio-frequency sputtering on flexible plastic substrates

    Science.gov (United States)

    Wang, Li-Min; Wang, Chih-Yi; Jheng, Ciao-Ren; Wu, Syu-Jhan; Sai, Chen-Kai; Lee, Ya-Ju; Chiang, Ching-Yu; Shew, Bor-Yuan

    2016-08-01

    The crystalline structure, morphology, composition, electrical transport, and optical properties of aluminum-doped zinc oxide (AZO) films are studied for applications in transparent electronics and optoelectronic devices. AZO thin films of c-axis-oriented growth and with different thickness were deposited on PET flexible plastic substrates at room temperature by rf magnetron sputtering. A larger grain size with a decreased strain ɛ value is observed in a thicker film, while changes in composition for films with different thicknesses are insignificant. Moreover, the resistivity of film decreases with increasing thickness, and the low-temperature electrical transport properties can be described by the scenario of quantum corrections to conductivity. With the room-temperature growth conditions, the resistivity of 4.5 × 10-4 Ω cm, carrier concentration of 6.4 × 1020 cm-3, and transmittance of 80 % for the 1100-nm-thick film are obtained. In addition, the optical bandgap energy decreases with increasing film thickness, which can be attributed to the bandgap renormalization and crystallite size effects.

  2. Preparation of well-aligned carbon nanotubes/silicon nanowires core-sheath composite structure arrays in porous anodic aluminum oxide templates

    Institute of Scientific and Technical Information of China (English)

    李梦轲; 力虎林; 陆梅; 王成伟

    2002-01-01

    The well-aligned carbon nanotubes (CNTs) arrays with opened ends were prepared in ordered pores of anodic aluminum oxide (AAO) template by the chemical vapor deposition (CVD) method. After then, silicon nanowires (SiNWs) were deposited in the hollow cavities of CNTs. By using this method, CNTs/SiNWs core-sheath composite structure arrays were synthesized successfully. Growing structures and physical properties of the CNTs/SiNWs composite structure arrays were analyzed and researched by the scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction spectrum (XRD), respectively. The field emission (FE) behavior of the CNTs/SiNWs composite structure arrays was studied based on Fowler-Nordheim tunneling mechanism and current-voltage (/-V) curve. And the photoluminescence (PL) was also characterized. Significantly, the CNTs/SiNWs core-sheath composite structure nanowire fabricated by AAO template method is characteristic of a metal/semiconductor (M/S) behavior and can be

  3. Effect of the Milling Time of the Precursors on the Physical Properties of Sprayed Aluminum-Doped Zinc Oxide (ZnO:Al Thin Films

    Directory of Open Access Journals (Sweden)

    María De La Luz Olvera

    2012-08-01

    Full Text Available Aluminum doped zinc oxide (ZnO:Al thin films were deposited on soda-lime glass substrates by the chemical spray technique. The atomization of the solution was carried out by ultrasonic excitation. Six different starting solutions from both unmilled and milled Zn and Al precursors, dissolved in a mix of methanol and acetic acid, were prepared. The milling process was carried out using a planetary ball mill at a speed of 300 rpm, and different milling times, namely, 15, 25, 35, 45, and 60 min. Molar concentration, [Al]/[Zn] atomic ratio, deposition temperature and time, were kept at constant values; 0.2 M, 3 at.%, 475 °C, and 10 min, respectively. Results show that, under the same deposition conditions, electrical resistivities of ZnO:Al thin films deposited from milled precursors are lower than those obtained for films deposited from unmilled precursors. X-ray diffraction analysis revealed that all films display a polycrystalline structure, fitting well with the hexagonal wurtzite structure. Changes in surface morphology were observed by scanning electron microscopy (SEM as well, since films deposited from unmilled precursors show triangular shaped grains, in contrast to films deposited from 15 and 35 min milled precursors that display thin slices with hexagonal shapes. The use of milled precursors to prepare starting solutions for depositing ZnO:Al thin films by ultrasonic pyrolysis influences their physical properties.

  4. Aluminum-doped zinc oxide sol–gel thin films: Influence of the sol's water content on the resistivity

    Energy Technology Data Exchange (ETDEWEB)

    Nehmann, Julia B., E-mail: nehmann@isfh.de [Institute for Solar Energy Research Hamelin (ISFH), Am Ohrberg 1, 31860 Emmerthal (Germany); Ehrmann, Nicole; Reineke-Koch, Rolf [Institute for Solar Energy Research Hamelin (ISFH), Am Ohrberg 1, 31860 Emmerthal (Germany); Bahnemann, Detlef W. [Institute for Technical Chemistry, Gottfried Wilhelm Leibniz University Hannover, Callinstrasse 3A, 30167 Hannover (Germany)

    2014-04-01

    Thin films of indium tin oxide (ITO) have gained substantial interest due to their optical and electrical properties. Since ITO is an expensive material and indium is a rare element, considerable attempts have been made to replace it by, e.g., aluminum-doped zinc oxide (ZnO:Al). The production of ZnO:Al is less cost-intensive, especially if the sol–gel technique is applied, while its properties are comparable to those of ITO. In this study, we demonstrate that the electrical properties of ZnO:Al thin films can be improved considerably by the addition of small amounts of ultrapure water to the dip coating solution during the preparation. The lowest resistivity obtained with a film prepared from a sol containing 0.2 M water is 2.8·10{sup −3Ω}cm. Optical modeling thus indicates an improvement of the free carrier mobility of films prepared from sols in the presence of additional water. The films prepared have an average thickness of 340 nm and a solar transmittance above 85% after annealing in a forming gas atmosphere. Clearly, the addition of water to the sol has a positive impact on the resistivity of the final ZnO:Al thin film. We suggest the observed increase of the free carrier mobility to be due to an improved electron transfer at the grain boundaries between the spherical nanoparticles. - Highlights: • We prepared ZnO:Al thin films with additional water in the sol by dip coating. • We found a positive impact of the water in the sol on the resistivity of the film. • The free carrier concentration and mobility increased with additional 0.2 M water. • The refractive indices demonstrate a denser structure related to the water content.

  5. Aluminum-doped zinc oxide sol–gel thin films: Influence of the sol's water content on the resistivity

    International Nuclear Information System (INIS)

    Thin films of indium tin oxide (ITO) have gained substantial interest due to their optical and electrical properties. Since ITO is an expensive material and indium is a rare element, considerable attempts have been made to replace it by, e.g., aluminum-doped zinc oxide (ZnO:Al). The production of ZnO:Al is less cost-intensive, especially if the sol–gel technique is applied, while its properties are comparable to those of ITO. In this study, we demonstrate that the electrical properties of ZnO:Al thin films can be improved considerably by the addition of small amounts of ultrapure water to the dip coating solution during the preparation. The lowest resistivity obtained with a film prepared from a sol containing 0.2 M water is 2.8·10−3Ωcm. Optical modeling thus indicates an improvement of the free carrier mobility of films prepared from sols in the presence of additional water. The films prepared have an average thickness of 340 nm and a solar transmittance above 85% after annealing in a forming gas atmosphere. Clearly, the addition of water to the sol has a positive impact on the resistivity of the final ZnO:Al thin film. We suggest the observed increase of the free carrier mobility to be due to an improved electron transfer at the grain boundaries between the spherical nanoparticles. - Highlights: • We prepared ZnO:Al thin films with additional water in the sol by dip coating. • We found a positive impact of the water in the sol on the resistivity of the film. • The free carrier concentration and mobility increased with additional 0.2 M water. • The refractive indices demonstrate a denser structure related to the water content

  6. Gas phase structures and charge localization in small aluminum oxide anions: Infrared photodissociation spectroscopy and electronic structure calculations

    Science.gov (United States)

    Song, Xiaowei; Fagiani, Matias R.; Gewinner, Sandy; Schöllkopf, Wieland; Asmis, Knut R.; Bischoff, Florian A.; Berger, Fabian; Sauer, Joachim

    2016-06-01

    We use cryogenic ion trap vibrational spectroscopy in combination with quantum chemical calculations to study the structure of mono- and dialuminum oxide anions. The infrared photodissociation spectra of D2-tagged AlO1-4- and Al2O3-6- are measured in the region from 400 to 1200 cm-1. Structures are assigned based on a comparison to simulated harmonic and anharmonic IR spectra derived from electronic structure calculations. The monoaluminum anions contain an even number of electrons and exhibit an electronic closed-shell ground state. The Al2O3-6- anions are oxygen-centered radicals. As a result of a delicate balance between localization and delocalization of the unpaired electron, only the BHLYP functional is able to qualitatively describe the observed IR spectra of all species with the exception of AlO3-. Terminal Al-O stretching modes are found between 1140 and 960 cm-1. Superoxo and peroxo stretching modes are found at higher (1120-1010 cm-1) and lower energies (850-570 cm-1), respectively. Four modes in-between 910 and 530 cm-1 represent the IR fingerprint of the common structural motif of dialuminum oxide anions, an asymmetric four-member Al-(O)2-Al ring.

  7. TEM analysis and wear resistance of the ceramic coatings on Q235 steel prepared by hybrid method of hot-dipping aluminum and plasma electrolytic oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Lu Lihong [State Key Laboratory of Metastable Materials Science and Technology, College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); Science and Research Department, Chinese People' s Armed Police Academy, Langfang 065000 (China); Zhang Jingwu [State Key Laboratory of Metastable Materials Science and Technology, College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); Shen Dejiu, E-mail: sdj217@ysu.edu.cn [State Key Laboratory of Metastable Materials Science and Technology, College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); Wu Lailei; Jiang Guirong [State Key Laboratory of Metastable Materials Science and Technology, College of Materials Science and Engineering, Yanshan University, Qinhuangdao 066004 (China); Li Liang [State Key Laboratory of Automotive Safety and Energy, Tsinghua University, Beijing 100084 (China)

    2012-01-25

    Highlights: Black-Right-Pointing-Pointer Transmission electron microscopy (TEM) was firstly used to analyze the phase composition of the ceramic coatings. Black-Right-Pointing-Pointer The phase composition of the ceramic coatings is mainly amorphous phase and crystal Al{sub 2}O{sub 3} oxides. Black-Right-Pointing-Pointer The cross-section micro-hardness of the treated samples was investigated, the hardness of the ceramic coatings is about HV1300. Black-Right-Pointing-Pointer The wear resistance of the PEO samples is about 3 times higher than that of the heat treated 45 steel. - Abstract: The hybrid method of PEO and hot-dipping aluminum (HDA) was employed to deposit composite ceramic coatings on the surface of Q235 steel. The composition of the composite coatings was investigated with X-ray diffraction (XRD) and transmission electron microscopy (TEM), respectively. The cross-section microstructure and micro-hardness of the treated specimens were investigated and analyzed with scanning electron microscopy (SEM) and microscopic hardness meter (MHM), respectively. The wear resistance of the ceramic coatings was investigated by a self-made rubbing wear testing machine. The results indicate that metallurgical bonding can be observed between the ceramic coatings and the steel substrate. There are many micro-pores and micro-cracks, which act as the discharge channels and result of quick and non-uniform cooling of melted sections in the plasma electrolytic oxidation ceramic coatings. The phase composition of the ceramic coatings is mainly composed of amorphous phase and crystal Al{sub 2}O{sub 3} oxides. The crystal Al{sub 2}O{sub 3} phase includes {kappa}-Al{sub 2}O{sub 3}, {theta}-Al{sub 2}O{sub 3} and {beta}-Al{sub 2}O{sub 3}. The grain size of the {kappa}-Al{sub 2}O{sub 3} crystal is quite non-uniform. The hardness of the ceramic coatings is about HV1300 and 10 times higher than that of the Q235 substrate, which was favorable to the better wear resistance of the ceramic

  8. Influence of wet etching time cycles on morphology features of thin porous Anodic Aluminum oxide (AAO) template for nanostructure's synthesis

    Science.gov (United States)

    Chahrour, Khaled M.; Ahmed, Naser M.; Hashim, M. R.; Elfadill, Nezar G.; Al-Diabat, Ahmad M.; Bououdina, M.

    2015-12-01

    This study examines the influence of chemical wet etching time cycles on the morphological features of thin porous AAO template. Pore widening via wet-etching treatment at room temperature was found to modify the pore quality of AAO template and reduces the barrier layer on the bottom of AAO pore array in order to facilitate uniform electrodeposition of nanostructures onto AAO template. High quality AAO pore arrays with different mean pore diameters (64, 70, and 87 nm) were prepared under controllable pore-widening time cycles of 10, 30 and 45 min at room temperature, respectively. The AAO templates and the produced Cu nanorods were characterized using FESEM, EDX, XRD and AFM. The results indicate that the morphology of the aligned arrays of Cu nanorods is strongly affected by the duration of etching and the removal of AAO template. This study showed that the optimum etching duration required to maintain the aligned nanorods without any fracture is approximately 5 min. In addition, the regular hemispherical concave Al surface ensuring the self-ordering of AAO pore can be established when striping is employed for 45 min. Thus, it can be inferred that the duration of wet etching treatment (striping) of Al oxide film performed after the first-step anodization plays a vital role in the final arrangement of nanopores.

  9. Adhesive strength and structure of micro-arc oxidation ceramic coatings grown in-situ on LY12 aluminum alloy

    Institute of Scientific and Technical Information of China (English)

    WU Zhen-dong; JIANG Zhao-hua; YAO Zhong-ping

    2006-01-01

    The ceramic coatings containing zirconium dioxide were grown in-situ on LY12 aluminium alloy by micro-arc oxidation in mixed zirconate and phosphate solution. The phase composition and morphology of the coatings were studied by XRD and SEM.The adhesive strength of ceramic coatings was assessed by thermal shock test and tensile test. The results show that the coating is composed of m-ZrO2, t-ZrO2, and a little γ-Al2O3. Along the section of the coating, t-ZrO2 is more onboth sides than that in the middle, while m-ZrO2 is more in the middle than that on both sides. Meantime the coating is also composed of a dense layer and a loose layer. The coating has excellent thermal shock resistance under 550 ℃ and 600 ℃. And tensile tests show the adhesive strength of the dense layer of the coating with the substrate is more than 17.5 MPa.

  10. Aluminum doped nickel oxide thin film with improved electrochromic performance from layered double hydroxides precursor in situ pyrolytic route

    Science.gov (United States)

    Shi, Jingjing; Lai, Lincong; Zhang, Ping; Li, Hailong; Qin, Yumei; Gao, Yuanchunxue; Luo, Lei; Lu, Jun

    2016-09-01

    Electrochromic materials with unique performance arouse great interest on account of potential application values in smart window, low-power display, automobile anti-glare rearview mirror, and e-papers. In this paper, high-performing Al-doped NiO porous electrochromic film grown on ITO substrate has been prepared via a layered double hydroxides(LDHs) precursor in situ pyrolytic route. The Al3+ ions distributed homogenously within the NiO matrix can significantly influence the crystallinity of Ni-Al LDH and NiO:Al3+ films. The electrochromic performance of the films were evaluated by means of UV-vis absorption spectroscopy, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and chronoamperometry(CA) measurements. In addition, the ratio of Ni3+/Ni2+ also varies with Al content which can lead to different electrochemical performances. Among the as-prepared films, NiO film prepared from Ni-Al (19:1) LDH show the best electrochromic performance with a high transparency of 96%, large optical modulation range (58.4%), fast switching speed (bleaching/coloration times are 1.8/4.2 s, respectively) and excellent durability (30% decrease after 2000 cycles). The improved performance was owed to the synergy of large NiO film specific surface area and porous morphology, as well as Al doping stifled the formation of Ni3+ making bleached state more pure. This LDHs precursor pyrolytic method is simple, low-cost and environmental benign and is feasible for the preparation of NiO:Al and other Al-doped oxide thin film.

  11. Anodizing of aluminum with improved corrosion properties

    International Nuclear Information System (INIS)

    Anodizing of aluminum was studied in sulphuric/oxalic/boric acid electroiyte system. The corrosion resistance of the anodic oxide coating of aluminum was determined by potentiodynamic polarization test and scanning electron microscope (SEM) was used to investigate the surface morphology before and after corrosion test. It was found that the oxide coating obtained by this method showed better corrosion resistance with no significant difference in surface morphology. (author)

  12. Physical and chemical degradation behavior of sputtered aluminum doped zinc oxide layers for Cu(In,Ga)Se2 solar cells

    International Nuclear Information System (INIS)

    Sputtered aluminum doped zinc oxide (ZnO:Al) layers on borosilicate glass were exposed to damp heat (85 °C/85% relative humidity) for 2876 h to accelerate the physical and chemical degradation behavior. The ZnO:Al samples were characterized by electrical, compositional and optical measurements before and after degradation. Hall measurements show that the carrier concentration stayed constant, while the Hall mobility decreased and the overall resistivity thus increased. This can be explained by the increase of potential barriers at the grain boundaries due to the occurrence of space charge regions caused by additional electron trapping sites. X-Ray Diffraction and optical measurements show that the crystal structure and transmission in the range 300–1100 nm do no change, hereby confirming that the bulk structure stays constant. Furthermore, on the surface, white spots appeared, containing elements that migrated from the glass, like silicon and calcium, which reacted with elements from the environment, including oxygen, carbon and chlorine. Depth profiling showed that the increase of the potential barrier is caused by the diffusion of H2O/OH− through the grain boundaries leading to the formation of Zn(OH)2 or similar species or adsorption of species. They also indicate the presence of chloride and sulfide in the top layer and the possible presence of Zn5(OH)8Cl2·H2O and Zn4SO4(OH)6·nH2O - Highlights: • Damp heat treatment of polycrystalline ZnO:Al leads to increased resistivity. • Degradation in electrical properties is due to decreased mobility. • Damp heat exposure does not influence optical properties between 300 and 1100 nm. • Water as well as carbon, chlorine and sulfur diffuse into the ZnO:Al bulk. • Possible reaction products are zinc hydroxide and zinc hydrocarbonate

  13. Aluminum doping tunes band gap energy level as well as oxidative stress-mediated cytotoxicity of ZnO nanoparticles in MCF-7 cells

    Science.gov (United States)

    Akhtar, Mohd Javed; Alhadlaq, Hisham A.; Alshamsan, Aws; Majeed Khan, M. A.; Ahamed, Maqusood

    2015-09-01

    We investigated whether Aluminum (Al) doping tunes band gap energy level as well as selective cytotoxicity of ZnO nanoparticles in human breast cancer cells (MCF-7). Pure and Al-doped ZnO nanoparticles were prepared by a simple sol-gel method. Characterization study confirmed the formation of single phase of AlxZn1-xO nanocrystals with the size range of 33-55 nm. Al-doping increased the band gap energy of ZnO nanoparticles (from 3.51 eV for pure to 3.87 eV for Al-doped ZnO). Al-doping also enhanced the cytotoxicity and oxidative stress response of ZnO nanoparticles in MCF-7 cells. The IC50 for undoped ZnO nanoparticles was 44 μg/ml while for the Al-doped ZnO counterparts was 31 μg/ml. Up-regulation of apoptotic genes (e.g. p53, bax/bcl2 ratio, caspase-3 & caspase-9) along with loss of mitochondrial membrane potential suggested that Al-doped ZnO nanoparticles induced apoptosis in MCF-7 cells through mitochondrial pathway. Importantly, Al-doping did not change the benign nature of ZnO nanoparticles towards normal cells suggesting that Al-doping improves the selective cytotoxicity of ZnO nanoparticles toward MCF-7 cells without affecting the normal cells. Our results indicated a novel approach through which the inherent selective cytotoxicity of ZnO nanoparticles against cancer cells can be further improved.

  14. The formation of tungsten doped Al2O3/ZnO coatings on aluminum by plasma electrolytic oxidation and their application in photocatalysis

    Science.gov (United States)

    Stojadinović, Stevan; Vasilić, Rastko; Radić, Nenad; Tadić, Nenad; Stefanov, Plamen; Grbić, Boško

    2016-07-01

    Tungsten doped Al2O3/ZnO coatings are formed by plasma electrolytic oxidation of aluminum substrate in supporting electrolyte (0.1 M boric acid + 0.05 M borax + 2 g/L ZnO) with addition of different concentrations of Na2WO4·2H2O. The morphology, crystal structure, chemical composition, and light absorption characteristics of formed surface coatings are investigated. The X-ray diffraction and X-ray photoelectron spectroscopy results indicate that formed surface coatings consist of alpha and gamma phase of Al2O3, ZnO, metallic tungsten and WO3. Obtained results showed that incorporated tungsten does not have any influence on the absorption spectra of Al2O3/ZnO coatings, which showed invariable band edge at about 385 nm. The photocatalytic activity of undoped and tungsten doped Al2O3/ZnO coatings is estimated by the photodegradation of methyl orange. The photocatalytic activity of tungsten doped Al2O3/ZnO coatings is higher thanof undoped Al2O3/ZnO coatings; the best photocatalytic activity is ascribed to coatings formed in supporting electrolyte with addition of 0.3 g/L Na2WO4·2H2O. Tungsten in Al2O3/ZnO coatings acts as a charge trap, thus reducing the recombination rate of photogenerated electron-hole pairs. The results of PL measurements are in agreement with photocatalytic activity. Declining PL intensity corresponds to increasing photocatalytic activity of the coatings, indicating slower recombination of electron-hole pairs.

  15. Aluminum oxide from trimethylaluminum and water by atomic layer deposition: The temperature dependence of residual stress, elastic modulus, hardness and adhesion

    International Nuclear Information System (INIS)

    Use of atomic layer deposition (ALD) in microelectromechanical systems (MEMS) has increased as ALD enables conformal growth on 3-dimensional structures at relatively low temperatures. For MEMS device design and fabrication, the understanding of stress and mechanical properties such as elastic modulus, hardness and adhesion of thin film is crucial. In this work a comprehensive characterization of the stress, elastic modulus, hardness and adhesion of ALD aluminum oxide (Al2O3) films grown at 110–300 °C from trimethylaluminum and water is presented. Film stress was analyzed by wafer curvature measurements, elastic modulus by nanoindentation and surface-acoustic wave measurements, hardness by nanoindentation and adhesion by microscratch test and scanning nanowear. The films were also analyzed by ellipsometry, optical reflectometry, X-ray reflectivity and time-of-flight elastic recoil detection for refractive index, thickness, density and impurities. The ALD Al2O3 films were under tensile stress in the scale of hundreds of MPa. The magnitude of the stress decreased strongly with increasing ALD temperature. The stress was stable during storage in air. Elastic modulus and hardness of ALD Al2O3 saturated to a fairly constant value for growth at 150 to 300 °C, while ALD at 110 °C gave softer films with lower modulus. ALD Al2O3 films adhered strongly on cleaned silicon with SiOx termination. - Highlights: • The residual stress of Al2O3 was tensile and stable during the storage in air. • Elastic modulus of Al2O3 saturated to at 170 GPa for films grown at 150 to 300 °C. • At 110 °C Al2O3 films were softer with high residual hydrogen and lower density. • The Al2O3 adhered strongly on the SiOx-terminated silicon

  16. Aluminum-based metal-air batteries

    Science.gov (United States)

    Friesen, Cody A.; Martinez, Jose Antonio Bautista

    2016-01-12

    Provided in one embodiment is an electrochemical cell, comprising: (i) a plurality of electrodes, comprising a fuel electrode that comprises aluminum and an air electrode that absorbs gaseous oxygen, the electrodes being operable in a discharge mode wherein the aluminum is oxidized at the fuel electrode and oxygen is reduced at the air electrode, and (ii) an ionically conductive medium, comprising an organic solvent; wherein during non-use of the cell, the organic solvent promotes formation of a protective interface between the aluminum of the fuel electrode and the ionically conductive medium, and wherein at an onset of the discharge mode, at least some of the protective interface is removed from the aluminum to thereafter permit oxidation of the aluminum during the discharge mode.

  17. Metal-ceramic adhesion: Synthesis of aluminum and chromium mixed metal oxides and extended Hueckel modeling of metal-metal oxide interfaces

    Energy Technology Data Exchange (ETDEWEB)

    Boorse, R.S.

    1993-01-01

    Methods of chemical synthesis and theoretical calculation was used to form new materials that have improved adhesion of a thin metal film to a ceramic. Two goals of this investigation were to develop new synthesis of metal-ceramic couples with improved adhesion between the two components and a fundamental understanding of the chemical factors that affect adhesion. Extended Hueckel calculations were performed on a series of Pt- and NiPt-NiO metal-ceramic couples to examine bonding. The calculations showed an 5 fold increase in adhesion energy in NiPt-NiO over Pt-NiO. Bonding across the interface is found to decrease with increased electron donation as interfacially antibonding orbitals are filled. The synthesis of (Al[sub 1[minus]x]Cr[sub x])[sub 2]O[sub 3] mixed metal oxide powders and coatings by sol-gel methodology utilizing three chromium precursors is reported. Thus, Al[Cr(CO)[sub 3]C[sub 5]H[sub 5

  18. Aluminum oxide as a dual-functional modifier of Ni-based anodes of solid oxide fuel cells for operation on simulated biogas

    Science.gov (United States)

    Wang, Feng; Wang, Wei; Ran, Ran; Tade, Moses O.; Shao, Zongping

    2014-12-01

    Al2O3 and SnO2 additives are introduced into the Ni-YSZ cermet anode of solid oxide fuel cells (SOFCs) for operation on simulated biogas. The effects of incorporating Al2O3/SnO2 on the electrical conductivity, morphology, coking resistance and catalytic activity for biogas reforming of the cermet anode are systematically studied. The electrochemical performance of the internal reforming SOFC is enhanced by introducing an appropriate amount of Al2O3 into the anode, but it becomes worse with excess alumina addition. For SnO2, a negative effect on the electrochemical performance is demonstrated, although the coking resistance of the anode is improved. For fuel cells operating on biogas, stable operation under a polarization current for 130 h at 750 °C is achieved for a cell with an Al2O3-modified anode, while cells with unmodified or SnO2-modified Ni-YSZ anodes show much poorer stability under the same conditions. The improved performance of the cell with the Al2O3-modified anode mainly results from the suppressed coking and sintering of the anode and from the formation of NiAl2O4 in the unreduced anode. In sum, modifying the anode with Al2O3 may be a useful and facile way to improve the coking resistance and electrochemical performance of the nickel-based cermet anodes for SOFCs.

  19. Method of forming aluminum oxynitride material and bodies formed by such methods

    Science.gov (United States)

    Bakas, Michael P [Ammon, ID; Lillo, Thomas M [Idaho Falls, ID; Chu, Henry S [Idaho Falls, ID

    2010-11-16

    Methods of forming aluminum oxynitride (AlON) materials include sintering green bodies comprising aluminum orthophosphate or another sacrificial material therein. Such green bodies may comprise aluminum, oxygen, and nitrogen in addition to the aluminum orthophosphate. For example, the green bodies may include a mixture of aluminum oxide, aluminum nitride, and aluminum orthophosphate or another sacrificial material. Additional methods of forming aluminum oxynitride (AlON) materials include sintering a green body including a sacrificial material therein, using the sacrificial material to form pores in the green body during sintering, and infiltrating the pores formed in the green body with a liquid infiltrant during sintering. Bodies are formed using such methods.

  20. Reactive self-heating model of aluminum spherical nanoparticles

    OpenAIRE

    Martirosyan, Karen S; Zyskin, Maxim

    2012-01-01

    Aluminum-oxygen reaction is important in many highly energetic, high pressure generating systems. Recent experiments with nanostructured thermites suggest that oxidation of aluminum nanoparticles occurs in a few microseconds. Such rapid reaction cannot be explained by a conventional diffusion-based mechanism. We present a rapid oxidation model of a spherical aluminum nanoparticle, using Cabrera-Mott moving boundary mechanism, and taking self-heating into account. In our model, electric potent...

  1. The Technological Improvements of Aluminum Alloy Coloring by Electrolysis

    Institute of Scientific and Technical Information of China (English)

    LI Nai-jun

    2004-01-01

    The technological process of coloring golden-tawny on aluminum alloy by electrolysis was improved in this paper. The optimum composition of electrolyte was found, the conditions of deposition and anodic oxidation by electrolysis were studied. The oxidative membrane on aluminum alloy was satisfying, the colored aluminum alloy by electrolysis is uniformity,bright and beautiful, and the coloring by electrolysis is convenient and no pollution.

  2. Effect of Na2WO4 on Growth Process and Corrosion Resistance of Micro-arc Oxidation Coatings on 2A12 Aluminum Alloys in CH3COONa Electrolyte

    Science.gov (United States)

    Lin, Zhaoqing; Yu, Huijun; He, Siyu; Wang, Diangang; Chen, Chuanzhong

    2016-01-01

    Ceramic coatings were deposited on 2A12 aluminum alloys using micro-arc oxidation (MAO) technology in CH3COONa-Na2WO4 electrolyte. The MAO process was studied by recording the current-time curve. The influences of Na2WO4 concentrations on the coatings in CH3COONa electrolyte were investigated. The results show that the Na2WO4 concentrations affect the MAO process and performances of the coatings directly. Na2WO4 in excess is harmful for the formation of Al2O3 in this electrolyte. The corrosion resistance was enhanced with the decrease of Na2WO4 concentration.

  3. 多孔阳极氧化铝模板组装Fe纳米线及其表征%Preparation and Characterization of Fe Nanowire Arrays Embedded in Porous Anodic Aluminum Oxide Templates

    Institute of Scientific and Technical Information of China (English)

    迟广俊; 姚素薇

    2004-01-01

    Fe nanowire arrays are prepared by electrodeposition in porous anodic aluminum oxide template from a composite electrolyte solution. These nanowires have an uniform diameter of approximate 25 nm and a length in excess of 2.5μm. The micrographs and crystal structures of Fe nanowires are studied by transmission electron microscopy (TEM), selected-area electron diffraction (SAED), and X-ray diffraction(XRD). It is found that each nanowire is essentially a single crystal and has a different orientation in each array. Hysteresis loops of Fe nanowire array show that its easy magnetization direction is perpendicular to the sample plane.

  4. Size- and shape-controlled synthesis and catalytic performance of iron–aluminum mixed oxide nanoparticles for NO{sub X} and SO{sub 2} removal with hydrogen peroxide

    Energy Technology Data Exchange (ETDEWEB)

    Ding, Jie [School of Chemical Engineering, Nanjing University of Science and Technology, Nanjing, Jiangsu 210094 (China); Nanjing AIREP Environmental Protection Technology Co., Ltd., Nanjing, Jiangsu 210091 (China); Zhong, Qin, E-mail: zq304@mail.njust.edu.cn [School of Chemical Engineering, Nanjing University of Science and Technology, Nanjing, Jiangsu 210094 (China); Nanjing AIREP Environmental Protection Technology Co., Ltd., Nanjing, Jiangsu 210091 (China); Zhang, Shule; Cai, Wei [School of Chemical Engineering, Nanjing University of Science and Technology, Nanjing, Jiangsu 210094 (China); Nanjing AIREP Environmental Protection Technology Co., Ltd., Nanjing, Jiangsu 210091 (China)

    2015-02-11

    Graphical abstract: - Highlights: • The size- and shape-controllable synthesis of NIAO(x/y) is introduced. • The catalytic decomposition of H{sub 2}O{sub 2} on NIAO(x/y) is utilized for NO{sub X} and SO{sub 2} removal. • NIAO(7/3) shows highest NO{sub X} (80%) and SO{sub 2} (100%) removal. • The aluminum dramatically improves the structure and surface properties of catalysts. • The catalytic mechanism and well stability is investigated. - Abstract: A novel, simple, reproducible and low-cost strategy is introduced for the size- and shape-controlled synthesis of iron–aluminum mixed oxide nanoparticles (NIAO(x/y)). The as-synthesized NIAO(x/y) catalyze decomposition of H{sub 2}O{sub 2} yielding highly reactive hydroxyl radicals (·OH) for NO{sub X} and SO{sub 2} removal. 100% SO{sub 2} removal is achieved. NIAO(x/y) with Fe/Al molar ratio of 7/3 (NIAO(7/3)) shows the highest NO{sub X} removal of nearly 80% at >170 °C, whereas much lower NO{sub X} removal (<63%) is obtained for NIAO(3/7). The melting of aluminum oxides in NIAO(7/3) promotes the formation of lamellar products, thus improving the specific surface areas and mesoporous distribution, benefiting the production of ·OH radicals. Furthermore, the NIAO(7/3) leads to the minor increase of points of zero charges (PZC), apparent enhancement of FeOH content and high oxidizing ability of Fe(III), further improving the production of ·OH radicals. However, the NIAO(3/7) results in the formation of aluminum surface-enriched spherical particles, thus decreasing the surface atomic ratio of iron oxides, decreasing ·OH radical production. More importantly, the generation of FeOAl causes the decline of active sites. Finally, the catalytic decomposition of H{sub 2}O{sub 2} on NIAO(x/y) is proposed. And the well catalytic stability of NIAO(7/3) is obtained for evaluation of 30 h.

  5. Structural and magnetic characterization of as-prepared and annealed FeCoCu nanowire arrays in ordered anodic aluminum oxide templates

    Energy Technology Data Exchange (ETDEWEB)

    Rodríguez-González, B., E-mail: jbenito@uvigo.es [CACTI, University of Vigo, E-36310 Vigo (Spain); International Iberian Nanotechnology Laboratory, INL. Av. Mestre J. Veiga, 4715-330 Braga (Portugal); Bran, C.; Warnatz, T.; Vazquez, M. [Institute of Materials Science of Madrid, CSIC, 28049 Madrid (Spain); Rivas, J. [International Iberian Nanotechnology Laboratory, INL. Av. Mestre J. Veiga, 4715-330 Braga (Portugal)

    2014-04-07

    Herein, we report on the preparation, structure, and magnetic characterization of FeCoCu nanowire arrays grown by DC electrodeposition inside self-assembled ordered nanopores of anodic aluminum oxide templates. A systematic study of their structure has been performed both in as-prepared samples and after annealing in the temperature range up to 800 °C, although particular attention has been paid to annealing at 700 °C after which maximum magnetic hardening is achieved. The obtained nanowires have a diameter of 40 nm and their Fe{sub 0.28}Co{sub 0.67}Cu{sub 0.05} composition was confirmed by energy dispersive X-ray spectroscopy (EDS). Focused ion-beam lamellas of two samples (as-prepared and annealed at 700 °C) were prepared for their imaging in the high-resolution transmission electron microscopy (HRTEM) perpendicularly to the electron beam, where the obtained EDS compositional mappings show a homogeneous distribution of the elements. X-ray diffraction analysis, and selected area electron diffraction (SAED) patterns confirm that nanowires exhibit a bcc cubic structure (space group Im-3m). In addition, bright-dark field images show that the nanowires have a polycrystalline structure that remains essentially the same after annealing, but some modifications were observed: (i) an overall increase and sharpening of recrystallized grains, and (ii) an apparent shrinkage of the nanowires diameter. Obtained SAED patterns also show strong textured components with determined <111> and <112> crystalline directions parallel to the wires growth direction. The presence of both directions was also confirmed in the HRTEM images doing Fourier transform analyses. Magnetic measurements show strong magnetic anisotropy with magnetization easy axis parallel to the nanowires in as-prepared and annealed samples. The magnetic properties are tuned by suitable thermal treatments so that, maximum enhanced coercivity (∼2.7 kOe) and normalized remanence (∼0.91 Ms) values are

  6. Platinum-Enhanced Electron Transfer and Surface Passivation through Ultrathin Film Aluminum Oxide (Al₂O₃) on Si(111)-CH₃ Photoelectrodes.

    Science.gov (United States)

    Kim, Hark Jin; Kearney, Kara L; Le, Luc H; Pekarek, Ryan T; Rose, Michael J

    2015-04-29

    We report the preparation, stability, and utility of Si(111)-CH3 photoelectrodes protected with thin films of aluminum oxide (Al2O3) prepared by atomic layer deposition (ALD). The photoelectrodes have been characterized by X-ray photoelectron spectroscopy (XPS), photoelectrochemistry (Fc in MeCN, Fc-OH in H2O), electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV) simulation. XPS analysis of the growing Al2O3 layer affords both the thickness, and information regarding two-dimensional versus three-dimensional mode of growth. Impedance measurements on Si(111)|CH3|Al2O3 devices reveal that the nascent films (5-30 Å) exhibit significant capacitance, which is attenuated upon surpassing the bulk threshold (∼30 Å). The Al2O3 layer provides enhanced photoelectrochemical (PEC) stability evidenced by an increase in the anodic window of operation in MeCN (up to +0.5 V vs Ag) and enhanced stability in aqueous electrolyte (up to +0.2 V vs Ag). XPS analysis before and after PEC confirms the Al2O3 layer is persistent and prevents surface corrosion (SiOx). Sweep-rate dependent CVs in MeCN at varying thicknesses exhibit a trend of increasingly broad features, characteristic of slow electron transport kinetics. Simulations were modeled as slow electron transfer through a partially resistive and electroactive Al2O3 layer. Lastly, we find that the Al2O3 ultrathin film serves as a support for the ALD deposition of Pt nanoparticles (d ≈ 8 nm) that enhance electron transfer through the Al2O3 layer. Surface recombination velocity (SRV) measurements on the assembled Si(111)|CH3|Al2O3-15 device affords an S value of 4170 cm s(-1) (τ = 4.2 μs) comparable to the bare Si(111)-CH3 surface (3950 cm s(-1); τ = 4.4 μs). Overall, the results indicate that high electronic quality and low surface defect densities can be retained throughout a multistep assembly of an integrated and passivated semiconductor|thin-film|metal device. PMID:25880534

  7. X-ray photoelectron spectroscopy study of catalyzed aluminum carbide formation at aluminum-carbon interfaces

    Science.gov (United States)

    Rabenberg, L.; Maruyama, Benji

    1990-01-01

    Aluminum carbide may form at aluminum-graphite interfaces during the high-temperature processing of graphite fiber-reinforced aluminum metal matrix composites. The chemical interactions leading to the formation of the aluminum carbide in the solid state involve the breaking of the carbon-carbon bonds within the graphite, the transport of the carbon atoms across the interface, and the reaction with the aluminum to form Al4C3. The aluminum carbide formation process has been followed using X-ray photoelectron spectroscopy of model, thin-film, reaction couples. The overall reaction is shown to be catalyzed by the presence of water vapor. Water at the interface increases reaction kinetics by apparently weakening the bonds between the surface carbon atoms and their substrate. This result is in general agreement with what is known to occur during the oxidation of graphite in air.

  8. Gating of Permanent Molds for ALuminum Casting

    Energy Technology Data Exchange (ETDEWEB)

    David Schwam; John F. Wallace; Tom Engle; Qingming Chang

    2004-03-30

    This report summarizes a two-year project, DE-FC07-01ID13983 that concerns the gating of aluminum castings in permanent molds. The main goal of the project is to improve the quality of aluminum castings produced in permanent molds. The approach taken was determine how the vertical type gating systems used for permanent mold castings can be designed to fill the mold cavity with a minimum of damage to the quality of the resulting casting. It is evident that somewhat different systems are preferred for different shapes and sizes of aluminum castings. The main problems caused by improper gating are entrained aluminum oxide films and entrapped gas. The project highlights the characteristic features of gating systems used in permanent mold aluminum foundries and recommends gating procedures designed to avoid common defects. The study also provides direct evidence on the filling pattern and heat flow behavior in permanent mold castings.

  9. Characterization of ultrafine aluminum nanoparticles

    International Nuclear Information System (INIS)

    Aluminum nanopowders with particle sizes ranging from ∼25 nm to 80 nm were characterized by a variety of methods. We present and compare the results from common powder characterization techniques including transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM), BET gas adsorption surface area analysis, thermogravimetric analysis (TGA), photon correlation spectroscopy (PCS), and low angle laser light scattering (LALLS). Aluminum nanoparticles consist of an aluminum core with an aluminum oxide coating. HRTEM measurements of both the particle diameter and oxide layer thickness tend to be larger than those obtained from BET and TGA. LALLS measurements show a large degree of particle agglomeration in solution; therefore, primary particle sizes could not be determined. Furthermore, results from small-angle scattering techniques (SAS), including small-angle neutron (SANS) and x-ray (SAXS) scattering are presented and show excellent agreement with the BET, TGA, and HRTEM. The suite of analytical techniques presented in this paper can be used as a powerful tool in the characterization of many types of nanosized powders.

  10. Absorptive coating for aluminum solar panels

    Science.gov (United States)

    Desmet, D.; Jason, A.; Parr, A.

    1979-01-01

    Method for coating forming coating of copper oxide from copper component of sheet aluminum/copper alloy provides strong durable solar heat collector panels. Copper oxide coating has solar absorption characteristics similar to black chrome and is much simpler and less costly to produce.

  11. Al/sub 2/S/sub 3/ preparation and use in electrolysis process for aluminum production

    Science.gov (United States)

    Hsu, C.C.; Loutfy, R.O.; Yao, N.P.

    A continuous process for producing aluminum sulfide and for electrolyzing the aluminum sulfide to form metallic aluminum in which the aluminum sulfide is produced from aluminum oxide and COS or CS/sub 2/ in the presence of a chloride melt which also serves as the electrolysis bath. Circulation between the reactor and electrolysis cell is carried out to maintain the desired concentration of aluminum sulfide in the bath.

  12. Superhydrophobic coating deposited directly on aluminum

    Energy Technology Data Exchange (ETDEWEB)

    Escobar, Ana M., E-mail: annaescobarromero@ub.edu; Llorca-Isern, Nuria

    2014-06-01

    This study develops an alternative method for enhancing superhydrophobicity on aluminum surfaces with an amphiphilic reagent such as the dodecanoic acid. The goal is to induce superhydrophobicity directly through a simple process on pure (99.9 wt%) commercial aluminum. The initial surface activation leading to the formation of the superhydrophobic coating is studied using confocal microscopy. Superhydrophobic behavior is analyzed by contact angle measurements, scanning electron microscopy (SEM) and atomic force microscopy (AFM). The highest contact angle (approaching 153°) was obtained after forming hierarchical structures with a particular roughness obtained by grinding and polishing microgrooves on the aluminum surface together with the simultaneous action of HCl and dodecanoic acid. The results also showed that after immersion in the ethanol-acidic-fatty acid solutions, they reacted chemically through the action of the fatty acid, on the aluminum surface. The mechanism is analyzed by TOF-SIMS and XPS in order to determine the molecules involved in the reaction. The TOF-SIMS analysis revealed that the metal and its oxides seem to be necessary, and that free-aluminum is anchored to the fatty acid molecules and to the alumina molecules present in the medium. Consequently, both metallic aluminum and aluminum oxides are necessary in order to form the compound responsible for superhydrophobicity.

  13. Improving pitting corrosion resistance of aluminum by anodizing process

    International Nuclear Information System (INIS)

    Summary: Anodizing of aluminum was studied in sulphuric/citric/boric acid electrolyte system to improve pitting corrosion resistance. Maximum oxide film thickness was obtained using 5% sulphuric acid, 3% citric acid and 0.5% boric acid electrolyte composition. The corrosion resistance of aluminum sample was determined to find the effectiveness of oxide coating by potentiodynamic polarization test. The surface morphology of aluminum samples was investigated using scanning electron microscope (SEM) before and after corrosion test. It was found that the coated aluminum sample obtained by anodizing in sulphuric/citric/boric acid electrolyte system exhibited better pitting corrosion resistance with no significant difference in surface morphology. (author)

  14. Surface-catalyzed chlorine and nitrogen activation: mechanisms for the heterogeneous formation of ClNO, NO, NO2, HONO, and N2O from HNO3 and HCl on aluminum oxide particle surfaces.

    Science.gov (United States)

    Rubasinghege, Gayan; Grassian, Vicki H

    2012-05-31

    It is well-known that chlorine active species (e.g., Cl(2), ClONO(2), ClONO) can form from heterogeneous reactions between nitrogen oxides and hydrogen chloride on aerosol particle surfaces in the stratosphere. However, less is known about these reactions in the troposphere. In this study, a potential new heterogeneous pathway involving reaction of gaseous HCl and HNO(3) on aluminum oxide particle surfaces, a proxy for mineral dust in the troposphere, is proposed. We combine transmission Fourier transform infrared spectroscopy with X-ray photoelectron spectroscopy to investigate changes in the composition of both gas-phase and surface-bound species during the reaction under different environmental conditions of relative humidity and simulated solar radiation. Exposure of surface nitrate-coated aluminum oxide particles, from prereaction with nitric acid, to gaseous HCl yields several gas-phase products, including ClNO, NO(2), and HNO(3), under dry (RH 20%), NO and N(2)O are the only gas products observed. The experimental data suggest that, in the presence of adsorbed water, ClNO is hydrolyzed on the particle surface to yield NO and NO(2), potentially via a HONO intermediate. NO(2) undergoes further hydrolysis via a surface-mediated process, resulting in N(2)O as an additional nitrogen-containing product. In the presence of broad-band irradiation (λ > 300 nm) gas-phase products can undergo photochemistry, e.g., ClNO photodissociates to NO and chlorine atoms. The gas-phase product distribution also depends on particle mineralogy (Al(2)O(3) vs CaCO(3)) and the presence of other coadsorbed gases (e.g., NH(3)). These newly identified reaction pathways discussed here involve continuous production of active ozone-depleting chlorine and nitrogen species from stable sinks such as gas-phase HCl and HNO(3) as a result of heterogeneous surface reactions. Given that aluminosilicates represent a major fraction of mineral dust aerosol, aluminum oxide can be used as a model

  15. Spark Plasma Sintering of MgO-Strengthened Aluminum

    Science.gov (United States)

    Ben-Haroush, M.; Dikovsky, G.; Kalabukhov, S.; Aizenshtein, M.; Hayun, S.

    2016-02-01

    The effects of MgO as a sintering additive, sintering duration, and post-heat treatment on mechanical properties and microstructure of spark plasma-sintered aluminum powders were investigated. The sinterability of aluminum with or without MgO was found to be sensitive to the aluminum average particle size, meaning the amount of native oxide within the raw aluminum powders. The fracture mode changes gradually from a brittle mode (after short SPS), through a mixed brittle-ductile fracture mode (after long SPS), ending with the pure ductile form (short SPS followed by heat treatment). Maxima flexural strength and elongation were found in samples with particles size of about 44 μm and the addition of 2 wt.% MgO after short SPS process followed by an additional heat treatment. The addition of MgO may contribute to perforation of the aluminum native oxide and enhance aluminum diffusion during the heat treatment.

  16. The Aluminum Smelting Process

    OpenAIRE

    Kvande, Halvor

    2014-01-01

    This introduction to the industrial primary aluminum production process presents a short description of the electrolytic reduction technology, the history of aluminum, and the importance of this metal and its production process to modern society. Aluminum's special qualities have enabled advances in technologies coupled with energy and cost savings. Aircraft capabilities have been greatly enhanced, and increases in size and capacity are made possible by advances in aluminum technology. The me...

  17. A liquid aluminum corrosion resistance surface on steel substrate

    International Nuclear Information System (INIS)

    The process of hot dipping pure aluminum on a steel substrate followed by oxidation was studied to form a surface layer of aluminum oxide resistant to the corrosion of aluminum melt. The thickness of the pure aluminum layer on the steel substrate is reduced with the increase in temperature and time in initial aluminizing, and the thickness of the aluminum layer does not increase with time at given temperature when identical temperature and complete wetting occur between liquid aluminum and the substrate surface. The thickness of the Fe-Al intermetallic layer on the steel base is increased with increasing bath temperature and time. Based on the experimental data and the mathematics model developed by the study, a maximum exists in the thickness of the Fe-Al intermetallic at certain dipping temperature. X-ray diffraction (XRD) and energy dispersive X-ray (EDX) analysis reveals that the top portion of the steel substrate is composed of a thin layer of α-Al2O3, followed by a thinner layer of FeAl3, and then a much thicker one of Fe2Al5 on the steel base side. In addition, there is a carbon enrichment zone in diffusion front. The aluminum oxide surface formed on the steel substrate is in perfect condition after corrosion test in liquid aluminum at 750 deg. C for 240 h, showing extremely good resistance to aluminum melt corrosion

  18. Investigation of trap properties in high-k/metal gate p-type metal-oxide-semiconductor field-effect-transistors with aluminum ion implantation using random telegraph noise analysis

    Energy Technology Data Exchange (ETDEWEB)

    Kao, Tsung-Hsien; Chang, Shoou-Jinn, E-mail: changsj@mail.ncku.edu.tw; Fang, Yean-Kuen; Huang, Po-Chin [Institute of Microelectronics and Department of Electrical Engineering, Advanced Optoelectronic Technology Center, Center for Micro/Nano Science and Technology, National Cheng Kung University, No. 1, University Road, Tainan 701, Taiwan (China); Lai, Chien-Ming; Hsu, Chia-Wei; Chen, Yi-Wen; Cheng, Osbert [Central R and D Division, United Microelectronics Corporation, Ltd., Tainan Science-Based Industrial Park, Tainan 74145, Taiwan (China); Wu, Chung-Yi; Wu, San-Lein [Department of Electronic Engineering, Cheng Shiu University, 840 Chengcing Road, Niaosong, Kaohsiung 833, Taiwan (China)

    2014-08-11

    In this study, the impact of aluminum ion implantation (Al I/I) on random telegraph noise (RTN) in high-k/metal gate (HK/MG) p-type metal-oxide-semiconductor field-effect-transistors (pMOSFETs) was investigated. The trap parameters of HK/MG pMOSFETs with Al I/I, such as trap energy level, capture time and emission time, activation energies for capture and emission, and trap location in the gate dielectric, were determined. The configuration coordinate diagram was also established. It was observed that the implanted Al could fill defects and form a thin Al{sub 2}O{sub 3} layer and thus increase the tunneling barrier height for holes. It was also observed that the trap position in the Al I/I samples was lower due to the Al I/I-induced dipole at the HfO{sub 2}/SiO{sub 2} interface.

  19. Investigation of trap properties in high-k/metal gate p-type metal-oxide-semiconductor field-effect-transistors with aluminum ion implantation using random telegraph noise analysis

    International Nuclear Information System (INIS)

    In this study, the impact of aluminum ion implantation (Al I/I) on random telegraph noise (RTN) in high-k/metal gate (HK/MG) p-type metal-oxide-semiconductor field-effect-transistors (pMOSFETs) was investigated. The trap parameters of HK/MG pMOSFETs with Al I/I, such as trap energy level, capture time and emission time, activation energies for capture and emission, and trap location in the gate dielectric, were determined. The configuration coordinate diagram was also established. It was observed that the implanted Al could fill defects and form a thin Al2O3 layer and thus increase the tunneling barrier height for holes. It was also observed that the trap position in the Al I/I samples was lower due to the Al I/I-induced dipole at the HfO2/SiO2 interface

  20. Electrometallurgical treatment of aluminum-based fuels

    International Nuclear Information System (INIS)

    We have successfully demonstrated aluminum electrorefining from a U-Al-Si alloy that simulates spent aluminum-based reactor fuel. The aluminum product contains less than 200 ppm uranium. All the results obtained have been in agreement with predictions based on equilibrium thermodynamics. We have also demonstrated the need for adequate stirring to achieve a low-uranium product. Most of the other process steps have been demonstrated in other programs. These include uranium electrorefining, transuranic fission product scrubbing, fission product oxidation, and product consolidation by melting. Future work will focus on the extraction of active metal and rare earth fission products by a molten flux salt and scale-up of the aluminum electrorefining

  1. Ultrafine nanoporous palladium-aluminum film fabricated by citric acid-assisted hot-water-treatment of aluminum-palladium alloy film

    OpenAIRE

    Takashi Harumoto; Yohei Tamura; Takashi Ishiguro

    2015-01-01

    Hot-water-treatment has been adapted to fabricate ultrafine nanoporous palladium-aluminum film from aluminum-palladium alloy film. Using citric acid as a chelating agent, a precipitation of boehmite (aluminum oxide hydroxide, AlOOH) on the nanoporous palladium-aluminum film was suppressed. According to cross-sectional scanning transmission electron microscopy observations, the ligament/pore sizes of the prepared nanoporous film were considerably small (on the order of 10 nm). Since this fabri...

  2. Electrochemical study of aluminum corrosion in boiling high purity water

    Science.gov (United States)

    Draley, J. E.; Legault, R. A.

    1969-01-01

    Electrochemical study of aluminum corrosion in boiling high-purity water includes an equation relating current and electrochemical potential derived on the basis of a physical model of the corrosion process. The work involved an examination of the cathodic polarization behavior of 1100 aluminum during aqueous oxidation.

  3. Graphene-aluminum nanocomposites

    International Nuclear Information System (INIS)

    Highlights: → We investigated the mechanical properties of aluminum and aluminum nanocomposites. → Graphene composite had lower strength and hardness compared to nanotube reinforcement. → Processing causes aluminum carbide formation at graphene defects. → The carbides in between grains is a source of weakness and lowers tensile strength. - Abstract: Composites of graphene platelets and powdered aluminum were made using ball milling, hot isostatic pressing and extrusion. The mechanical properties and microstructure were studied using hardness and tensile tests, as well as electron microscopy, X-ray diffraction and differential scanning calorimetry. Compared to the pure aluminum and multi-walled carbon nanotube composites, the graphene-aluminum composite showed decreased strength and hardness. This is explained in the context of enhanced aluminum carbide formation with the graphene filler.

  4. Graphene-aluminum nanocomposites

    Energy Technology Data Exchange (ETDEWEB)

    Bartolucci, Stephen F., E-mail: stephen.bartolucci@us.army.mil [U.S. Army Benet Laboratories, Armaments Research Development and Engineering Center, Watervliet, NY 12189-4000 (United States); Paras, Joseph [U.S. Army Benet Laboratories, Armaments Research Development and Engineering Center, Watervliet, NY 12189-4000 (United States); Rafiee, Mohammad A. [Department of Mechanical Engineering and Materials Science, Rice University, Houston, TX 77005 (United States); Rafiee, Javad [Department of Mechanical, Aerospace and Nuclear Engineering, Rensselaer Polytechnic Institute, Troy, New York 12180 (United States); Lee, Sabrina; Kapoor, Deepak [U.S. Army Benet Laboratories, Armaments Research Development and Engineering Center, Watervliet, NY 12189-4000 (United States); Koratkar, Nikhil, E-mail: koratn@rpi.edu [Department of Mechanical, Aerospace and Nuclear Engineering, Rensselaer Polytechnic Institute, Troy, New York 12180 (United States)

    2011-10-15

    Highlights: {yields} We investigated the mechanical properties of aluminum and aluminum nanocomposites. {yields} Graphene composite had lower strength and hardness compared to nanotube reinforcement. {yields} Processing causes aluminum carbide formation at graphene defects. {yields} The carbides in between grains is a source of weakness and lowers tensile strength. - Abstract: Composites of graphene platelets and powdered aluminum were made using ball milling, hot isostatic pressing and extrusion. The mechanical properties and microstructure were studied using hardness and tensile tests, as well as electron microscopy, X-ray diffraction and differential scanning calorimetry. Compared to the pure aluminum and multi-walled carbon nanotube composites, the graphene-aluminum composite showed decreased strength and hardness. This is explained in the context of enhanced aluminum carbide formation with the graphene filler.

  5. Research on Properties of Ceramic Coating on 2Al2 Aluminum Alloy bv Plasma Microarc Oxidation%2Al2铝合金微弧氧化膜性能研究

    Institute of Scientific and Technical Information of China (English)

    郭虹; 宫廷; 黄树涛; 周丽

    2011-01-01

    Microarc oxidation (MAO) coating on 2A12 aluminum alloy was prepared in Na2SiO3 and Na2WO4 electrolytes, and the surface morphology, cross-sectional microstructure, wear resistance and micro-hardness and ceramic coatings have been studied in detail. The results show that the microarc oxidation surface treatment can form a dense ceramic coating on 2A12 aluminum alloy, which has good adhesion with aluminum alloy substrate. The concentration of Na2WO4solution has significant influence on the color, surface morphology, density and micro-hardness of ceramic coating, but not much influence on the thickness of the ceramic coating. Additionally, the addition of Na2WO4 into the base Na2SiO3 electrolyte resulted in the increase of the micro-hardness of the ceramic coating, furthermore, the micro-hardness of the ceramic coating increased with the increasing distance from the interface.%采用Na2 WO4和Na2SO3电解液对2Al2铝合金进行微弧氧化,研究了微弧氧化陶瓷膜表面形貌、截面组织、显微硬度及耐磨性等性能.结果表明,微弧氧化表面处理可以在2Al2铝合金表面形成致密并与基体结合良好的陶瓷膜,Na2WO4溶液浓度对陶瓷膜颜色、表面形貌、致密度和显微硬度都有影响,但对于陶瓷膜成膜厚度没有显著影响.同时,在Na2SiO3电解液中添加Na2WO4将会导致陶瓷膜显微硬度的增加,而且随着与界面距离的增大,陶瓷膜显微硬度逐渐增加.

  6. 阳极氧化法制备多孔氧化铝膜的形成过程研究%Investigation on the growth sequence of porous anodic aluminum oxide films by two-step anodization

    Institute of Scientific and Technical Information of China (English)

    刘海凤; 路丙强; 梁冬林; 魏水强; 苟凯佩; 王凡; 文衍宣

    2012-01-01

    采用阳极氧化技术,研究了电压对多孔氧化铝膜生长过程的影响.使用扫描电镜( SEM)对在草酸-水-乙醇体系中形成的多孔氧化铝膜形貌进行观测.结果表明,在第二步氧化过程中,在40V氧化电压下,多孔氧化铝膜的有序度和孔径随反应时间延长而降低;在80 V下,经过长时间反应,AAO膜表面腐蚀严重,难以获得平整的多孔结构.预氧化过程所形成的薄氧化层有效保护了多孔氧化铝表面,同时对多孔结构具有短距离诱导作用.改变氧化电压、电解质浓度和反应时间,有序孔排列的结构参数也有所改变.高电场下,孔道的相互作用促进了其生长分化,形成了两种不同的孔道结构.%The detailed growth processes of porous anodic aluminum oxide films influenced by the applied voltage were studied via anodization method. The appearance of the porous anodic aluminum oxide films formed in oxalic acid-water-ethanol solution was studied by SEM. At the second anodization step, the ordering degree and pore size of oxide films decreased at 40 V, while the rough surface of AAO by severe corrosion was obtained at 80 V. Whereas, the surface oxide layer generated by pre-anodization provided effective protection at the early stage of high-voltage anodization, and guided the formation of ordered pores array in short range. The structural parameters of ordered pores array were dependent on the applied voltage, electrolyte concentration and reaction time. At high applied voltage, the cause of interaction forces between neighboring pores enhances the differentiation of pore growth, and hence two different pores growth behaviors in the internal and surface of AAO membrane are observed.

  7. Anodic oxidation of 6063 aluminum alloy with intermittent high current density%6063铝合金的大电流密度间歇式阳极氧化

    Institute of Scientific and Technical Information of China (English)

    黄元盛; 陈焕明

    2014-01-01

    The 6063 aluminum alloy was treated by anodic oxidation with high current density and intermittent current .The effects of anodic oxidation process on microstructure, thickness and properties of the oxide layer were investigated.The results show that with the anodic oxidation solution used in the experiment, the proper process parameters for anodic oxidation are determined with current density of 42-53 A/dm2 , on-off time ratio of 1∶1, and each conduction time of 0.5 s.The oxide layer prepared by the proper process parameters has micropores in the surface layer while the inner layer has no micropores , and the interface between film and substrate has high density .The maximum thickness and microhardness of the oxide layer can reach above 75 μm and 735 HV0.5 respectively, and the oxide layer shows excellent corrosion resistance in NaCl solution .%采用大电流密度间歇式电流阳极氧化工艺对6063铝合金进行氧化处理,研究了阳极氧化工艺对氧化层组织、厚度和性能的影响。结果表明,在试验用阳极氧化溶液下,确定了合理的阳极氧化工艺参数为:电流密度42~53 A/dm2,通断电时间比为1∶1,每次通电0.5 s。采用此工艺制得的氧化层表层有微孔,而内层未见有微孔,膜/基界面致密度高,氧化层的最大厚度达75μm以上,最大硬度达735 HV0.5,氧化层耐NaCl溶液腐蚀能力极好。

  8. Guangdong Aluminum to Raise RMB 3 billion for New Production Base in Guizhou

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    <正>On July 7, a loan signing ceremony was held between the Guangdong Aluminum Group, China Construction Bank, Hua Xia Bank and Guangzhou Bank Consortium. It is reported that these banks will provide Guangdong Aluminum Group with RMB 30 billion for an alu-minum oxide and supporting bauxite mining project in Guizhou.

  9. 75 FR 44184 - Aluminum tris(O-ethylphosphonate), Butylate, Chlorethoxyfos, Clethodim, et al.; Proposed...

    Science.gov (United States)

    2010-07-28

    ... AGENCY 40 CFR Part 180 Aluminum tris(O-ethylphosphonate), Butylate, Chlorethoxyfos, Clethodim, et al..., etofenprox, fenbutatin-oxide, fosthiazate, propetamphos, and tebufenozide; the fungicides aluminum tris(O... for aluminum tris(O-ethylphosphonate) on pineapple fodder and forage because they are not...

  10. Paint-Bonding Improvement for 2219 Aluminum Alloy

    Science.gov (United States)

    Daech, Alfred F.; Cibula, Audrey Y.

    1987-01-01

    Bonding of adhesives and primers to 2219 aluminum alloy improved by delaying rinse step in surface-treatment process. Delaying rinse allows formation of rougher surface for stronger bonding and greater oxide buildup.

  11. 无压浸渗法制备氧化态SiC颗粒增强铝基复合材料%Fabrication of Oxidized SiC Particles Reinforced Aluminum Matrix Composite by Pressureless Infiltration Technique

    Institute of Scientific and Technical Information of China (English)

    张强; 姜龙涛; 武高辉

    2012-01-01

    The oxidation behavior of SiC particles in the temperature range from l000℃ to 1200℃ was investi-gated. The dependence of weight gain and oxidation time was parabolic and the oxidation behavior was controlled by diffusion process, with a oxidation activation energy of 219 kJ/mol. Using oxidized SiC particles as reinforce-ment and aluminum alloy containing Si and Mg as matrix, a SiCp/Al composite was fabricated by pressureless infil-tration technique. The microstructure and interfacial morphology were analyzed and the pressureless infiltration mechanisms were discussed. The particles were distributed uniformly in the composite, without particles agglom-eration. Interfacial reactions were found in the composite and the product was identified as MgAl2O4, formed by the reactions between surface oxide layer of SiC particles and Mg, Al in the matrix. The interfacial reactions enhanced the wettability and promoted the spontaneous infiltration process.%研究了SiC颗粒在1000~1200℃的氧化行为,其氧化增重率与保温时间符合抛物线规律,氧化增重受扩散过程控制,氧化激活能为219 kJ/mol.采用预氧化处理的SiC颗粒为增强体,含Si、Mg的铝合金为基体,通过无压浸渗方法制备了SiCp/Al复合材料,分析了复合材料的微观组织与界面形貌,探讨了无压浸渗机理.复合材料中颗粒分布均匀,无偏聚现象.材料制备过程中存在界面反应,SiC颗粒表面的氧化层与铝合金中的Mg、Al反应形成了一定数量的MgAl2O4.界面反应的存在提高了润湿性,促进了无压自发浸渗.

  12. Synthesis and characterization of nanoporous anodic oxide film on aluminum in H3PO4 + KMnO4 electrolyte mixture at different anodization conditions

    Science.gov (United States)

    Verma, Naveen; Jindal, Jitender; Singh, Krishan Chander; Mari, Bernabe

    2016-04-01

    The micro structural properties of nanoporous anodic oxide film formed in H3PO4 were highly influenced by addition of a low concentration of KMnO4 (0.0005 M) in 1 M H3PO4 solution. The KMnO4 as additive enhanced the growth rate of oxide film formation as well as thickness of pore walls. Furthermore the growth rate was found increased with increase in applied current density. The increase in temperature and lack of stirring during anodization causes the thinness of pore wall which leads to increase in pore volume. With the decrease in concentration of H3PO4 in anodizing electrolyte from 1M to 0.3 M, keeping all other conditions constant, the decrease in porosity was observed. This might be due to the dissolution of aluminium oxide film in highly concentrated acidic solution.

  13. Electrically Conductive Anodized Aluminum Surfaces

    Science.gov (United States)

    Nguyen, Trung Hung

    2006-01-01

    Anodized aluminum components can be treated to make them sufficiently electrically conductive to suppress discharges of static electricity. The treatment was conceived as a means of preventing static electric discharges on exterior satin-anodized aluminum (SAA) surfaces of spacecraft without adversely affecting the thermal-control/optical properties of the SAA and without need to apply electrically conductive paints, which eventually peel off in the harsh environment of outer space. The treatment can also be used to impart electrical conductivity to anodized housings of computers, medical electronic instruments, telephoneexchange equipment, and other terrestrial electronic equipment vulnerable to electrostatic discharge. The electrical resistivity of a typical anodized aluminum surface layer lies between 10(exp 11) and 10(exp 13) Omega-cm. To suppress electrostatic discharge, it is necessary to reduce the electrical resistivity significantly - preferably to anodized surface becomes covered and the pores in the surface filled with a transparent, electrically conductive metal oxide nanocomposite. Filling the pores with the nanocomposite reduces the transverse electrical resistivity and, in the original intended outer-space application, the exterior covering portion of the nanocomposite would afford the requisite electrical contact with the outer-space plasma. The electrical resistivity of the nanocomposite can be tailored to a value between 10(exp 7) and 10(exp 12) Omega-cm. Unlike electrically conductive paint, the nanocomposite becomes an integral part of the anodized aluminum substrate, without need for adhesive bonding material and without risk of subsequent peeling. The electrodeposition process is compatible with commercial anodizing production lines. At present, the electronics industry uses expensive, exotic, electrostaticdischarge- suppressing finishes: examples include silver impregnated anodized, black electroless nickel, black chrome, and black copper. In

  14. An EXAFS Study of Platinum-Oxygen Bonds in the Metal-Support Interface of a Highly Dispersed Platinum/Aluminum Oxide Catalyst

    OpenAIRE

    Koningsberger, D.C.; Sayers, D.E.

    1985-01-01

    EXAFS measurements have been performed on the Pt LIII-edge of a highly dispersed (H/M~1.14) Pt/@c-Al{2}O{3} catalyst, reduced at 673 K after calcination at the same temperature. After reduction an oxidic platinum oxygen bond (2.05@9) is present with a very low average oxygen coordination number. This bond arises from a few not reduced platinum-oxide crystallites. Platinum oxygen bonds with a coordination distance of 2.65 @9 could be detected significantly due to the high quality of the EXAFS ...

  15. Uniform superhydrophobic surfaces using micro/nano complex structures formed spontaneously by a simple and cost-effective nonlithographic process based on anodic aluminum oxide technology

    International Nuclear Information System (INIS)

    This paper presents a uniform micro/nano double-roughened superhydrophobic surface with a high static contact angle (CA) and low contact angle hysteresis (CAH). The proposed micro/nano complex structured surfaces were self-fabricated simply and efficiently using a very simple and low-cost nonlithographic sequential process, which consists of aluminum (Al) sputtering, anodization of the Al layer and pore widening, without specific equipment and additional subsequent processes. The wetting properties of the fabricated surfaces were characterized by measuring the static CAs and the CAHs after plasma polymerized fluorocarbon coating with a low surface energy. The measured static CA and CAH were 154 ± 2.3° and 5.7 ± 0.8°, respectively, showing that the fabricated double-roughened surfaces exhibit superhydrophobic behaviors clearly. In addition, the proposed double-scaled surfaces at a wafer-level exhibited uniform superhydrophobic behaviors across the wafer with an apparent CA and CAH of 153.9 ± 0.8° and 4.9 ± 1.3°, respectively.

  16. Is the Aluminum Hypothesis Dead?

    OpenAIRE

    Lidsky, Theodore I.

    2014-01-01

    The Aluminum Hypothesis, the idea that aluminum exposure is involved in the etiology of Alzheimer disease, dates back to a 1965 demonstration that aluminum causes neurofibrillary tangles in the brains of rabbits. Initially the focus of intensive research, the Aluminum Hypothesis has gradually been abandoned by most researchers. Yet, despite this current indifference, the Aluminum Hypothesis continues to attract the attention of a small group of scientists and aluminum continues to be viewed w...

  17. High strength oxide dispersion strengthened silver aluminum alloys optimized for Bi2Sr2CaCu2O8+x round wire

    International Nuclear Information System (INIS)

    High strength dispersion strengthened (DS) Ag/Al alloys with various Al content are studied as candidates for sheathing Bi2Sr2CaCu2O8+x (Bi2212) wire. The Ag/Al alloys are fabricated by powder metallurgy and internally oxidized in pure oxygen. The time and temperature of the internal oxidation heat treatment is varied to maximize the strength after undergoing the Bi2212 partial melt process (PMP). Vickers micro-hardness number (HVN), room temperature tensile behavior, optical and scanning electron microscopy, ion channeling contrast imaging using a focused ion beam and electrical resistivity measurements are used to characterize the alloys. An Ag/0.2wt%Mg (Ag/Mg) alloy is used for comparison. Results show that internal oxidation at 650–700  ° C for 4 h produces the highest HVN for the DS Ag/Al alloy; when oxidized at 675 ° C for 4 h the HVN, yield strength and tensile strength of the DS Ag/Al are 50% higher than the corresponding values of Ag/Mg. Microstructural observations show that Al2O3 precipitates play the main role in strengthening the DS Ag/Al alloy. The alloy retains its fine grain structure and strength after PMP heat treatment. (paper)

  18. Regeneración ósea guiada utilizando membrana de óxido de aluminio en combinación con implantes oseointegrados Guided bone regeneration using aluminum oxide membrane in combination with osseointegrated implants

    Directory of Open Access Journals (Sweden)

    M. Isa Majluf

    2007-08-01

    Full Text Available La reabsorción ósea de los maxilares ha sido una de las mayores complicaciones al momento de rehabilitar a pacientes con implantes oseointegrados. El siguiente estudio evaluó la efectividad de la membrana de óxido de aluminio (alúmina, en la regeneración ósea de rebordes colapsados y alvéolos en los que se colocaron implantes. De un total de cinco pacientes seleccionados, se estudiaron siete sitios de los cuales tres correspondieron a un solo paciente. En cada sitio (alvéolo o reborde colapsado se colocó un implante de titanio del sistema HIS y una membrana no biodegradable de óxido de aluminio (Allumina®, la cual fue retirada a las 14 semanas. Todos los pacientes fueron sometidos al mismo procedimiento quirúrgico. La ganancia promedio en mm obtenidos en orden decreciente fue la siguiente: ANM: 1.7mm, ANME: 1.6mm, AND: 1.1mm, AV: 1.0mm, AP: 0.5mm. Los resultados radiográficos ratificaron los resultados clínicos en cuanto a neoformación ósea, observándose además una favorable densidad ósea periimplantaria. El análisis estadístico (basado en los resultados clínicos t-student fue significativo para todos los parámetros evaluados con excepción de AP.Alveolar bone loss has been a very important cause of complications in osseointegrated implant rehabilitation of edentulous patients. This paper evaluates the effectiveness of aluminum oxide membrane (Allumina in the collapsed alveolar ridge where implants were used. Seven sites were studied in 5 patients. In each of these sites a HIS implant plus a non-biodegradable oxide aluminum membrane (Allumina®, was placed for 14 weeks. All patients were treated with the same surgical protocol. The average gain (in mm obtained in decreasing order was as follows: ANM: 1.7 mm, ANME: 1.6 mm, AND: 1.1mm, AV: 1.0mm, AP: 0.5mm. The clinical results were radiographically verified and these showed bone neoformation, in addition to favorable peri-implant bone density. The t-Student statistical

  19. Anodizing Aluminum with Frills.

    Science.gov (United States)

    Doeltz, Anne E.; And Others

    1983-01-01

    "Anodizing Aluminum" (previously reported in this journal) describes a vivid/relevant laboratory experience for general chemistry students explaining the anodizing of aluminum in sulfuric acid and constrasting it to electroplating. Additions to this procedure and the experiment in which they are used are discussed. Reactions involved are also…

  20. Ultrafine nanoporous palladium-aluminum film fabricated by citric acid-assisted hot-water-treatment of aluminum-palladium alloy film

    International Nuclear Information System (INIS)

    Hot-water-treatment has been adapted to fabricate ultrafine nanoporous palladium-aluminum film from aluminum-palladium alloy film. Using citric acid as a chelating agent, a precipitation of boehmite (aluminum oxide hydroxide, AlOOH) on the nanoporous palladium-aluminum film was suppressed. According to cross-sectional scanning transmission electron microscopy observations, the ligament/pore sizes of the prepared nanoporous film were considerably small (on the order of 10 nm). Since this fabrication method only requires aluminum alloy film and hot-water with chelating agent, the ultrafine nanoporous film can be prepared simply and environmentally friendly